From 9bf8a1a79d549a0cf3b26c88d1ac8cdf07deafee Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Mon, 23 Jun 2008 20:33:06 +0200 Subject: [PATCH 001/750] pci: debug extra pci resources range Signed-off-by: Ingo Molnar --- drivers/pci/probe.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c index 3706ce7972d..27cdbb06c4d 100644 --- a/drivers/pci/probe.c +++ b/drivers/pci/probe.c @@ -275,6 +275,7 @@ static void pci_read_bases(struct pci_dev *dev, unsigned int howmany, int rom) } res->start = l64 & PCI_BASE_ADDRESS_MEM_MASK; res->end = res->start + sz64; + printk(KERN_INFO "PCI: %s reg %x 64bit mmio: [%llx, %llx]\n", pci_name(dev), reg, res->start, res->end); #else if (sz64 > 0x100000000ULL) { printk(KERN_ERR "PCI: Unable to handle 64-bit " @@ -290,6 +291,8 @@ static void pci_read_bases(struct pci_dev *dev, unsigned int howmany, int rom) res->end = sz; } #endif + } else { + printk(KERN_INFO "PCI: %s reg %x %s: [%llx, %llx]\n", pci_name(dev), reg, (res->flags & IORESOURCE_IO)? "io port":"32bit mmio", res->start, res->end); } } if (rom) { @@ -357,6 +360,7 @@ void __devinit pci_read_bridge_bases(struct pci_bus *child) res->start = base; if (!res->end) res->end = limit + 0xfff; + printk(KERN_INFO "PCI: bridge %s io port: [%llx, %llx]\n", pci_name(dev), res->start, res->end); } res = child->resource[1]; @@ -368,6 +372,7 @@ void __devinit pci_read_bridge_bases(struct pci_bus *child) res->flags = (mem_base_lo & PCI_MEMORY_RANGE_TYPE_MASK) | IORESOURCE_MEM; res->start = base; res->end = limit + 0xfffff; + printk(KERN_INFO "PCI: bridge %s 32bit mmio: [%llx, %llx]\n", pci_name(dev), res->start, res->end); } res = child->resource[2]; @@ -402,6 +407,7 @@ void __devinit pci_read_bridge_bases(struct pci_bus *child) res->flags = (mem_base_lo & PCI_MEMORY_RANGE_TYPE_MASK) | IORESOURCE_MEM | IORESOURCE_PREFETCH; res->start = base; res->end = limit + 0xfffff; + printk(KERN_INFO "PCI: bridge %s %sbit mmio pref: [%llx, %llx]\n", pci_name(dev), (res->flags & PCI_PREF_RANGE_TYPE_64)?"64":"32",res->start, res->end); } } -- GitLab From 76fbc263ff7e42ce8b21b8aee176e3c74b45f81a Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Mon, 23 Jun 2008 20:33:06 +0200 Subject: [PATCH 002/750] pci: debug extra pci bus resources Signed-off-by: Ingo Molnar --- drivers/pci/setup-bus.c | 35 +++++++++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+) diff --git a/drivers/pci/setup-bus.c b/drivers/pci/setup-bus.c index 8ddb918f5f5..c74a2bce083 100644 --- a/drivers/pci/setup-bus.c +++ b/drivers/pci/setup-bus.c @@ -537,6 +537,36 @@ void __ref pci_bus_assign_resources(struct pci_bus *bus) } EXPORT_SYMBOL(pci_bus_assign_resources); +static void pci_bus_dump_res(struct pci_bus *bus) +{ + int i; + + for (i = 0; i < PCI_BUS_NUM_RESOURCES; i++) { + struct resource *res = bus->resource[i]; + if (!res) + continue; + + printk(KERN_INFO "bus: %02x index %x %s: [%llx, %llx]\n", bus->number, i, (res->flags & IORESOURCE_IO)? "io port":"mmio", res->start, res->end); + } +} + +static void pci_bus_dump_resources(struct pci_bus *bus) +{ + struct pci_bus *b; + struct pci_dev *dev; + + + pci_bus_dump_res(bus); + + list_for_each_entry(dev, &bus->devices, bus_list) { + b = dev->subordinate; + if (!b) + continue; + + pci_bus_dump_resources(b); + } +} + void __init pci_assign_unassigned_resources(void) { @@ -552,4 +582,9 @@ pci_assign_unassigned_resources(void) pci_bus_assign_resources(bus); pci_enable_bridges(bus); } + + /* dump the resource on buses */ + list_for_each_entry(bus, &pci_root_buses, node) { + pci_bus_dump_resources(bus); + } } -- GitLab From 2bc7509f62da572925ef33365d4fc16f8b4abdd4 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Tue, 15 Jul 2008 17:17:48 +0100 Subject: [PATCH 003/750] [ARM] S3C24XX: s3c243xx_clock_register() data can be __initdata Any data being passed to s3c243xx_clock_register() can be marked as __initdata as it is an array of pointers to 'struct clk' that are to be registered on initialisation. The s3c243xx_clock_register function uses this array to register clocks and does not require it to stay around after exit. Signed-off-by: Ben Dooks --- arch/arm/mach-s3c2410/mach-bast.c | 2 +- arch/arm/mach-s3c2410/mach-vr1000.c | 2 +- arch/arm/mach-s3c2440/mach-anubis.c | 2 +- arch/arm/mach-s3c2440/mach-osiris.c | 2 +- 4 files changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/arm/mach-s3c2410/mach-bast.c b/arch/arm/mach-s3c2410/mach-bast.c index 965f2712970..5c289c3a437 100644 --- a/arch/arm/mach-s3c2410/mach-bast.c +++ b/arch/arm/mach-s3c2410/mach-bast.c @@ -562,7 +562,7 @@ static struct platform_device *bast_devices[] __initdata = { &bast_sio, }; -static struct clk *bast_clocks[] = { +static struct clk *bast_clocks[] __initdata = { &s3c24xx_dclk0, &s3c24xx_dclk1, &s3c24xx_clkout0, diff --git a/arch/arm/mach-s3c2410/mach-vr1000.c b/arch/arm/mach-s3c2410/mach-vr1000.c index 9a0965ac5e1..7be0bb629bf 100644 --- a/arch/arm/mach-s3c2410/mach-vr1000.c +++ b/arch/arm/mach-s3c2410/mach-vr1000.c @@ -344,7 +344,7 @@ static struct platform_device *vr1000_devices[] __initdata = { &vr1000_led3, }; -static struct clk *vr1000_clocks[] = { +static struct clk *vr1000_clocks[] __initdata = { &s3c24xx_dclk0, &s3c24xx_dclk1, &s3c24xx_clkout0, diff --git a/arch/arm/mach-s3c2440/mach-anubis.c b/arch/arm/mach-s3c2440/mach-anubis.c index 09af8b23500..0c33a932d65 100644 --- a/arch/arm/mach-s3c2440/mach-anubis.c +++ b/arch/arm/mach-s3c2440/mach-anubis.c @@ -414,7 +414,7 @@ static struct platform_device *anubis_devices[] __initdata = { &anubis_device_sm501, }; -static struct clk *anubis_clocks[] = { +static struct clk *anubis_clocks[] __initdata = { &s3c24xx_dclk0, &s3c24xx_dclk1, &s3c24xx_clkout0, diff --git a/arch/arm/mach-s3c2440/mach-osiris.c b/arch/arm/mach-s3c2440/mach-osiris.c index af996b0e91e..3869ca2c345 100644 --- a/arch/arm/mach-s3c2440/mach-osiris.c +++ b/arch/arm/mach-s3c2440/mach-osiris.c @@ -341,7 +341,7 @@ static struct platform_device *osiris_devices[] __initdata = { &osiris_pcmcia, }; -static struct clk *osiris_clocks[] = { +static struct clk *osiris_clocks[] __initdata = { &s3c24xx_dclk0, &s3c24xx_dclk1, &s3c24xx_clkout0, -- GitLab From 19c1d6a34abf73d0baf8e325d018c920fa78dddc Mon Sep 17 00:00:00 2001 From: "Arnaud Patard (Rtp" Date: Tue, 8 Jul 2008 01:03:46 +0200 Subject: [PATCH 004/750] [ARM] S3C24XX: Fix SERIAL_SAMSUNG entry The SERIAL_SAMSUNG needs SERIAL_CORE but doesn't select it, leading to a build failure. Adding a 'select SERIAL_CORE' cure the trouble. Signed-off-by: Arnaud Patard Signed-off-by: Ben Dooks --- drivers/serial/Kconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index 5a9754455ee..047c20d35a9 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -451,6 +451,7 @@ config SERIAL_CLPS711X_CONSOLE config SERIAL_SAMSUNG tristate "Samsung SoC serial support" depends on ARM && PLAT_S3C24XX + select SERIAL_CORE help Support for the on-chip UARTs on the Samsung S3C24XX series CPUs, providing /dev/ttySAC0, 1 and 2 (note, some machines may not -- GitLab From a83fe32fa668c0a17b3f99a1480b006f7d649924 Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Fri, 18 Jul 2008 13:22:36 -0700 Subject: [PATCH 005/750] x86, pci: detect end_bus_number according to acpi/e820 reserved, v2 Jack Howarth reported that 2.6.26-rc9-git9 doesn't boot on MacBookPro2. the reason is a faulty BIOS update that reportes faulty resources. Nevertheless it's possible for Linux to be more resolent about this situation (and similar situations) and work around this bug, by cross-checking the mmconf range against the e820 table and ACPI resources. Change the mconf bus range from [0,0xff] to to [0, 0x3f] to match range [0xf0000000, 0xf4000000) in e820 tables. [ v2, yhlu.kernel@gmail.com: x86, pci: detect end_bus_number according to acpi/e820 reserved - fix ] Reported-by: Jack Howarth Signed-off-by: Yinghai Lu Cc: jbarnes@virtuousgeek.org Cc: Jack Howarth Signed-off-by: Ingo Molnar --- arch/x86/pci/mmconfig-shared.c | 65 +++++++++++++++++++++++++--------- 1 file changed, 48 insertions(+), 17 deletions(-) diff --git a/arch/x86/pci/mmconfig-shared.c b/arch/x86/pci/mmconfig-shared.c index 23faaa890ff..429c7014feb 100644 --- a/arch/x86/pci/mmconfig-shared.c +++ b/arch/x86/pci/mmconfig-shared.c @@ -293,7 +293,7 @@ static acpi_status __init find_mboard_resource(acpi_handle handle, u32 lvl, return AE_OK; } -static int __init is_acpi_reserved(unsigned long start, unsigned long end) +static int __init is_acpi_reserved(u64 start, u64 end, unsigned not_used) { struct resource mcfg_res; @@ -310,6 +310,41 @@ static int __init is_acpi_reserved(unsigned long start, unsigned long end) return mcfg_res.flags; } +typedef int (*check_reserved_t)(u64 start, u64 end, unsigned type); + +static int __init is_mmconf_reserved(check_reserved_t is_reserved, + u64 addr, u64 size, int i, + typeof(pci_mmcfg_config[0]) *cfg, int with_e820) +{ + u64 old_size = size; + int valid = 0; + + while (!is_reserved(addr, addr + size - 1, E820_RESERVED)) { + size >>= 1; + if (size < (16UL<<20)) + break; + } + + if (size >= (16UL<<20) || size == old_size) { + printk(KERN_NOTICE + "PCI: MCFG area at %Lx reserved in %s\n", + addr, with_e820?"E820":"ACPI motherboard resources"); + valid = 1; + + if (old_size != size) { + /* update end_bus_number */ + cfg->end_bus_number = cfg->start_bus_number + ((size>>20) - 1); + printk(KERN_NOTICE "PCI: updated MCFG configuration %d: base %lx " + "segment %hu buses %u - %u\n", + i, (unsigned long)cfg->address, cfg->pci_segment, + (unsigned int)cfg->start_bus_number, + (unsigned int)cfg->end_bus_number); + } + } + + return valid; +} + static void __init pci_mmcfg_reject_broken(int early) { typeof(pci_mmcfg_config[0]) *cfg; @@ -324,21 +359,22 @@ static void __init pci_mmcfg_reject_broken(int early) for (i = 0; i < pci_mmcfg_config_num; i++) { int valid = 0; - u32 size = (cfg->end_bus_number + 1) << 20; + u64 addr, size; + cfg = &pci_mmcfg_config[i]; + addr = cfg->start_bus_number; + addr <<= 20; + addr += cfg->address; + size = cfg->end_bus_number + 1 - cfg->start_bus_number; + size <<= 20; printk(KERN_NOTICE "PCI: MCFG configuration %d: base %lx " "segment %hu buses %u - %u\n", i, (unsigned long)cfg->address, cfg->pci_segment, (unsigned int)cfg->start_bus_number, (unsigned int)cfg->end_bus_number); - if (!early && - is_acpi_reserved(cfg->address, cfg->address + size - 1)) { - printk(KERN_NOTICE "PCI: MCFG area at %Lx reserved " - "in ACPI motherboard resources\n", - cfg->address); - valid = 1; - } + if (!early) + valid = is_mmconf_reserved(is_acpi_reserved, addr, size, i, cfg, 0); if (valid) continue; @@ -347,16 +383,11 @@ static void __init pci_mmcfg_reject_broken(int early) printk(KERN_ERR "PCI: BIOS Bug: MCFG area at %Lx is not" " reserved in ACPI motherboard resources\n", cfg->address); + /* Don't try to do this check unless configuration type 1 is available. how about type 2 ?*/ - if (raw_pci_ops && e820_all_mapped(cfg->address, - cfg->address + size - 1, - E820_RESERVED)) { - printk(KERN_NOTICE - "PCI: MCFG area at %Lx reserved in E820\n", - cfg->address); - valid = 1; - } + if (raw_pci_ops) + valid = is_mmconf_reserved(e820_all_mapped, addr, size, i, cfg, 1); if (!valid) goto reject; -- GitLab From 026e2c05ef58ef413e2d52696f125d5ea1aa8bce Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Tue, 22 Jul 2008 11:58:14 +0200 Subject: [PATCH 006/750] x86, cyrix: debug Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/cyrix.c | 20 ++++++++++---------- include/asm-x86/processor-cyrix.h | 8 ++++++++ 2 files changed, 18 insertions(+), 10 deletions(-) diff --git a/arch/x86/kernel/cpu/cyrix.c b/arch/x86/kernel/cpu/cyrix.c index 3fd7a67bb06..db5868cd244 100644 --- a/arch/x86/kernel/cpu/cyrix.c +++ b/arch/x86/kernel/cpu/cyrix.c @@ -116,7 +116,7 @@ static void __cpuinit set_cx86_reorder(void) setCx86(CX86_CCR3, (ccr3 & 0x0f) | 0x10); /* enable MAPEN */ /* Load/Store Serialize to mem access disable (=reorder it) */ - setCx86(CX86_PCR0, getCx86(CX86_PCR0) & ~0x80); + setCx86_old(CX86_PCR0, getCx86_old(CX86_PCR0) & ~0x80); /* set load/store serialize from 1GB to 4GB */ ccr3 |= 0xe0; setCx86(CX86_CCR3, ccr3); @@ -127,11 +127,11 @@ static void __cpuinit set_cx86_memwb(void) printk(KERN_INFO "Enable Memory-Write-back mode on Cyrix/NSC processor.\n"); /* CCR2 bit 2: unlock NW bit */ - setCx86(CX86_CCR2, getCx86(CX86_CCR2) & ~0x04); + setCx86_old(CX86_CCR2, getCx86_old(CX86_CCR2) & ~0x04); /* set 'Not Write-through' */ write_cr0(read_cr0() | X86_CR0_NW); /* CCR2 bit 2: lock NW bit and set WT1 */ - setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x14); + setCx86_old(CX86_CCR2, getCx86_old(CX86_CCR2) | 0x14); } static void __cpuinit set_cx86_inc(void) @@ -144,10 +144,10 @@ static void __cpuinit set_cx86_inc(void) setCx86(CX86_CCR3, (ccr3 & 0x0f) | 0x10); /* enable MAPEN */ /* PCR1 -- Performance Control */ /* Incrementor on, whatever that is */ - setCx86(CX86_PCR1, getCx86(CX86_PCR1) | 0x02); + setCx86_old(CX86_PCR1, getCx86_old(CX86_PCR1) | 0x02); /* PCR0 -- Performance Control */ /* Incrementor Margin 10 */ - setCx86(CX86_PCR0, getCx86(CX86_PCR0) | 0x04); + setCx86_old(CX86_PCR0, getCx86_old(CX86_PCR0) | 0x04); setCx86(CX86_CCR3, ccr3); /* disable MAPEN */ } @@ -162,14 +162,14 @@ static void __cpuinit geode_configure(void) local_irq_save(flags); /* Suspend on halt power saving and enable #SUSP pin */ - setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x88); + setCx86_old(CX86_CCR2, getCx86_old(CX86_CCR2) | 0x88); ccr3 = getCx86(CX86_CCR3); setCx86(CX86_CCR3, (ccr3 & 0x0f) | 0x10); /* enable MAPEN */ /* FPU fast, DTE cache, Mem bypass */ - setCx86(CX86_CCR4, getCx86(CX86_CCR4) | 0x38); + setCx86_old(CX86_CCR4, getCx86_old(CX86_CCR4) | 0x38); setCx86(CX86_CCR3, ccr3); /* disable MAPEN */ set_cx86_memwb(); @@ -286,7 +286,7 @@ static void __cpuinit init_cyrix(struct cpuinfo_x86 *c) /* GXm supports extended cpuid levels 'ala' AMD */ if (c->cpuid_level == 2) { /* Enable cxMMX extensions (GX1 Datasheet 54) */ - setCx86(CX86_CCR7, getCx86(CX86_CCR7) | 1); + setCx86_old(CX86_CCR7, getCx86_old(CX86_CCR7) | 1); /* * GXm : 0x30 ... 0x5f GXm datasheet 51 @@ -309,7 +309,7 @@ static void __cpuinit init_cyrix(struct cpuinfo_x86 *c) if (dir1 > 7) { dir0_msn++; /* M II */ /* Enable MMX extensions (App note 108) */ - setCx86(CX86_CCR7, getCx86(CX86_CCR7)|1); + setCx86_old(CX86_CCR7, getCx86_old(CX86_CCR7)|1); } else { c->coma_bug = 1; /* 6x86MX, it has the bug. */ } @@ -424,7 +424,7 @@ static void __cpuinit cyrix_identify(struct cpuinfo_x86 *c) local_irq_save(flags); ccr3 = getCx86(CX86_CCR3); setCx86(CX86_CCR3, (ccr3 & 0x0f) | 0x10); /* enable MAPEN */ - setCx86(CX86_CCR4, getCx86(CX86_CCR4) | 0x80); /* enable cpuid */ + setCx86_old(CX86_CCR4, getCx86_old(CX86_CCR4) | 0x80); /* enable cpuid */ setCx86(CX86_CCR3, ccr3); /* disable MAPEN */ local_irq_restore(flags); } diff --git a/include/asm-x86/processor-cyrix.h b/include/asm-x86/processor-cyrix.h index 97568ada1f9..1198f2a0e42 100644 --- a/include/asm-x86/processor-cyrix.h +++ b/include/asm-x86/processor-cyrix.h @@ -28,3 +28,11 @@ static inline void setCx86(u8 reg, u8 data) outb(reg, 0x22); outb(data, 0x23); } + +#define getCx86_old(reg) ({ outb((reg), 0x22); inb(0x23); }) + +#define setCx86_old(reg, data) do { \ + outb((reg), 0x22); \ + outb((data), 0x23); \ +} while (0) + -- GitLab From bf068ee266f9dbaa6dacb8433a366bb399e7ae5b Mon Sep 17 00:00:00 2001 From: "Aneesh Kumar K.V" Date: Tue, 19 Aug 2008 22:16:43 -0400 Subject: [PATCH 007/750] ext4: Handle unwritten extent properly with delayed allocation When using fallocate the buffer_heads are marked unwritten and unmapped. We need to map them in the writepages after a get_block. Otherwise we split the uninit extents, but never write the content to disk. Signed-off-by: Aneesh Kumar K.V Signed-off-by: Mingming Cao Signed-off-by: "Theodore Ts'o" --- fs/ext4/inode.c | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-) diff --git a/fs/ext4/inode.c b/fs/ext4/inode.c index 59fbbe899ac..a1c7d762321 100644 --- a/fs/ext4/inode.c +++ b/fs/ext4/inode.c @@ -1741,6 +1741,13 @@ static void mpage_put_bnr_to_bhs(struct mpage_da_data *mpd, sector_t logical, if (buffer_delay(bh)) { bh->b_blocknr = pblock; clear_buffer_delay(bh); + bh->b_bdev = inode->i_sb->s_bdev; + } else if (buffer_unwritten(bh)) { + bh->b_blocknr = pblock; + clear_buffer_unwritten(bh); + set_buffer_mapped(bh); + set_buffer_new(bh); + bh->b_bdev = inode->i_sb->s_bdev; } else if (buffer_mapped(bh)) BUG_ON(bh->b_blocknr != pblock); @@ -1814,7 +1821,7 @@ static void mpage_da_map_blocks(struct mpage_da_data *mpd) * If blocks are delayed marked, we need to * put actual blocknr and drop delayed bit */ - if (buffer_delay(lbh)) + if (buffer_delay(lbh) || buffer_unwritten(lbh)) mpage_put_bnr_to_bhs(mpd, next, &new); /* go for the remaining blocks */ @@ -1823,7 +1830,8 @@ static void mpage_da_map_blocks(struct mpage_da_data *mpd) } } -#define BH_FLAGS ((1 << BH_Uptodate) | (1 << BH_Mapped) | (1 << BH_Delay)) +#define BH_FLAGS ((1 << BH_Uptodate) | (1 << BH_Mapped) | \ + (1 << BH_Delay) | (1 << BH_Unwritten)) /* * mpage_add_bh_to_extent - try to add one more block to extent of blocks -- GitLab From b4df2030858bde986cb6ff2e4b45945f84649e32 Mon Sep 17 00:00:00 2001 From: Theodore Ts'o Date: Wed, 13 Aug 2008 21:44:34 -0400 Subject: [PATCH 008/750] ext4: Fix potential truncate BUG due to i_prealloc_list being non-empty We need to call ext4_discard_reservation() earlier in ext4_truncate(), to avoid a BUG() in ext4_mb_return_to_preallocation(), which is called (ultimately) by ext4_free_blocks(). So we must ditch the blocks on i_prealloc_list before we start freeing the data blocks. Signed-off-by: "Theodore Ts'o" --- fs/ext4/inode.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/fs/ext4/inode.c b/fs/ext4/inode.c index a1c7d762321..2d54c822c4c 100644 --- a/fs/ext4/inode.c +++ b/fs/ext4/inode.c @@ -3494,6 +3494,9 @@ void ext4_truncate(struct inode *inode) * modify the block allocation tree. */ down_write(&ei->i_data_sem); + + ext4_discard_reservation(inode); + /* * The orphan list entry will now protect us from any crash which * occurs before the truncate completes, so it is now safe to propagate @@ -3563,8 +3566,6 @@ do_indirects: ; } - ext4_discard_reservation(inode); - up_write(&ei->i_data_sem); inode->i_mtime = inode->i_ctime = ext4_current_time(inode); ext4_mark_inode_dirty(handle, inode); -- GitLab From cd21322616c3af265d39bf15321d436e667a5dd1 Mon Sep 17 00:00:00 2001 From: Mingming Cao Date: Tue, 19 Aug 2008 22:16:59 -0400 Subject: [PATCH 009/750] ext4: Fix delalloc release block reservation for truncate Ext4 will release the reserved blocks for delayed allocations when inode is truncated/unlinked. If there is no reserved block at all, we shouldn't need to do so. But current code still tries to release the reserved blocks regardless whether the counters's value is 0. Continue to do that causes the later calculation to go wrong and a kernel BUG_ON() caught that. This doesn't happen for extent-based files, as the calculation for 0 reserved blocks was right for extent based file. This patch fixed the kernel BUG() due to above reason. It adds checks for 0 to avoid unnecessary release and fix calculation for non-extent files. Signed-off-by: Mingming Cao Signed-off-by: "Theodore Ts'o" --- fs/ext4/inode.c | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+) diff --git a/fs/ext4/inode.c b/fs/ext4/inode.c index 2d54c822c4c..5e17d5f22a7 100644 --- a/fs/ext4/inode.c +++ b/fs/ext4/inode.c @@ -1005,6 +1005,9 @@ static int ext4_indirect_calc_metadata_amount(struct inode *inode, int blocks) */ static int ext4_calc_metadata_amount(struct inode *inode, int blocks) { + if (!blocks) + return 0; + if (EXT4_I(inode)->i_flags & EXT4_EXTENTS_FL) return ext4_ext_calc_metadata_amount(inode, blocks); @@ -1559,7 +1562,25 @@ static void ext4_da_release_space(struct inode *inode, int to_free) struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb); int total, mdb, mdb_free, release; + if (!to_free) + return; /* Nothing to release, exit */ + spin_lock(&EXT4_I(inode)->i_block_reservation_lock); + + if (!EXT4_I(inode)->i_reserved_data_blocks) { + /* + * if there is no reserved blocks, but we try to free some + * then the counter is messed up somewhere. + * but since this function is called from invalidate + * page, it's harmless to return without any action + */ + printk(KERN_INFO "ext4 delalloc try to release %d reserved " + "blocks for inode %lu, but there is no reserved " + "data blocks\n", to_free, inode->i_ino); + spin_unlock(&EXT4_I(inode)->i_block_reservation_lock); + return; + } + /* recalculate the number of metablocks still need to be reserved */ total = EXT4_I(inode)->i_reserved_data_blocks - to_free; mdb = ext4_calc_metadata_amount(inode, total); -- GitLab From d015641734cde55d2fce48a6db3983c8a029fe05 Mon Sep 17 00:00:00 2001 From: Theodore Ts'o Date: Tue, 19 Aug 2008 21:57:43 -0400 Subject: [PATCH 010/750] ext4: Fix ext4_dx_readdir hash collision handling This fixes a bug where readdir() would return a directory entry twice if there was a hash collision in an hash tree indexed directory. Signed-off-by: Eugene Dashevsky Signed-off-by: Mike Snitzer Signed-off-by: "Theodore Ts'o" --- fs/ext4/dir.c | 20 +++++++++++++++----- 1 file changed, 15 insertions(+), 5 deletions(-) diff --git a/fs/ext4/dir.c b/fs/ext4/dir.c index d3d23d73c08..ec8e33b4521 100644 --- a/fs/ext4/dir.c +++ b/fs/ext4/dir.c @@ -411,7 +411,7 @@ static int call_filldir(struct file * filp, void * dirent, get_dtype(sb, fname->file_type)); if (error) { filp->f_pos = curr_pos; - info->extra_fname = fname->next; + info->extra_fname = fname; return error; } fname = fname->next; @@ -450,11 +450,21 @@ static int ext4_dx_readdir(struct file * filp, * If there are any leftover names on the hash collision * chain, return them first. */ - if (info->extra_fname && - call_filldir(filp, dirent, filldir, info->extra_fname)) - goto finished; + if (info->extra_fname) { + if (call_filldir(filp, dirent, filldir, info->extra_fname)) + goto finished; - if (!info->curr_node) + info->extra_fname = NULL; + info->curr_node = rb_next(info->curr_node); + if (!info->curr_node) { + if (info->next_hash == ~0) { + filp->f_pos = EXT4_HTREE_EOF; + goto finished; + } + info->curr_hash = info->next_hash; + info->curr_minor_hash = 0; + } + } else if (!info->curr_node) info->curr_node = rb_first(&info->root); while (1) { -- GitLab From 88aa3cff4e9a38b953de9fbc54c96e619a2bb9f9 Mon Sep 17 00:00:00 2001 From: Theodore Ts'o Date: Sat, 16 Aug 2008 07:57:35 -0400 Subject: [PATCH 011/750] ext4: Use ext4_discard_reservations instead of mballoc-specific call In ext4_ext_truncate(), we should use the more generic ext4_discard_reservations() call so we do the right thing when the filesystem is mounted with the nomballoc option. Signed-off-by: "Theodore Ts'o" Reviewed-by: Mingming Cao --- fs/ext4/extents.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/ext4/extents.c b/fs/ext4/extents.c index 612c3d2c382..7212947a8ca 100644 --- a/fs/ext4/extents.c +++ b/fs/ext4/extents.c @@ -2819,7 +2819,7 @@ void ext4_ext_truncate(struct inode *inode) down_write(&EXT4_I(inode)->i_data_sem); ext4_ext_invalidate_cache(inode); - ext4_mb_discard_inode_preallocations(inode); + ext4_discard_reservation(inode); /* * TODO: optimization is possible here. -- GitLab From 37609fd5ae62db75026d9f53096a1fbc35e040d9 Mon Sep 17 00:00:00 2001 From: Josef Bacik Date: Tue, 19 Aug 2008 22:13:41 -0400 Subject: [PATCH 012/750] ext4: don't try to resize if there are no reserved gdt blocks left When trying to resize an ext4 fs and you run out of reserved gdt blocks, you get an error that doesn't actually tell you what went wrong, it just says that the gdb it picked is not correct, which is the case since you don't have any reserved gdt blocks left. This patch adds a check to make sure you have reserved gdt blocks to use, and if not prints out a more relevant error. Signed-off-by: Josef Bacik Cc: Cc: Andreas Dilger Signed-off-by: Andrew Morton Signed-off-by: "Theodore Ts'o" --- fs/ext4/resize.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/fs/ext4/resize.c b/fs/ext4/resize.c index 0a926516426..b3d35604ea1 100644 --- a/fs/ext4/resize.c +++ b/fs/ext4/resize.c @@ -773,7 +773,8 @@ int ext4_group_add(struct super_block *sb, struct ext4_new_group_data *input) if (reserved_gdb || gdb_off == 0) { if (!EXT4_HAS_COMPAT_FEATURE(sb, - EXT4_FEATURE_COMPAT_RESIZE_INODE)){ + EXT4_FEATURE_COMPAT_RESIZE_INODE) + || !le16_to_cpu(es->s_reserved_gdt_blocks)) { ext4_warning(sb, __func__, "No reserved GDT blocks, can't resize"); return -EPERM; -- GitLab From c001077f4003fa75793bb62979baa6241dd8eb19 Mon Sep 17 00:00:00 2001 From: Eric Sandeen Date: Tue, 19 Aug 2008 22:19:50 -0400 Subject: [PATCH 013/750] ext4: Fix bug where we return ENOSPC even though we have plenty of inodes The find_group_flex() function starts with best_flex as the parent_fbg_group, which happens to have 0 inodes free. Some of the flex groups searched have free blocks and free inodes, but the flex_freeb_ratio is < 10, so they're skipped. Then when a group is compared to the current "best" flex group, it does not have more free blocks than "best", so it is skipped as well. This continues until no flex group with free inodes is found which has a proper ratio or which has more free blocks than the "best" group, and we're left with a "best" group that has 0 inodes free, and we return -ENOSPC. We fix this by changing the logic so that if the current "best" flex group has no inodes free, and the current one does have room, it is promoted to the next "best." Signed-off-by: Eric Sandeen Signed-off-by: "Theodore Ts'o" --- fs/ext4/ialloc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/ext4/ialloc.c b/fs/ext4/ialloc.c index 655e760212b..f344834bbf5 100644 --- a/fs/ext4/ialloc.c +++ b/fs/ext4/ialloc.c @@ -351,7 +351,7 @@ find_close_to_parent: goto found_flexbg; } - if (best_flex < 0 || + if (flex_group[best_flex].free_inodes == 0 || (flex_group[i].free_blocks > flex_group[best_flex].free_blocks && flex_group[i].free_inodes)) -- GitLab From a02908f19c819aeec5e3dcf238adaa6deddd70b0 Mon Sep 17 00:00:00 2001 From: Mingming Cao Date: Tue, 19 Aug 2008 22:16:07 -0400 Subject: [PATCH 014/750] ext4: journal credits calulation cleanup and fix for non-extent writepage When considering how many journal credits are needed for modifying a chunk of data, we need to account for the super block, inode block, quota blocks and xattr block, indirect/index blocks, also, group bitmap and group descriptor blocks for new allocation (including data and indirect/index blocks). There are many places in ext4 do the calculation on their own and often missed one or two meta blocks, and often they assume single block allocation, and did not considering the multile chunk of allocation case. This patch is trying to cleanup current journal credit code, provides some common helper funtion to calculate the journal credits, to be used for writepage, writepages, DIO, fallocate, migration, defrag, and for both nonextent and extent files. This patch modified the writepage/write_begin credit caculation for nonextent files, to use the new helper function. It also fixed the problem that writepage on nonextent files did not consider the case blocksize Reviewed-by: Aneesh Kumar K.V Signed-off-by: "Theodore Ts'o" --- fs/ext4/ext4.h | 3 + fs/ext4/ext4_jbd2.h | 8 +++ fs/ext4/inode.c | 131 ++++++++++++++++++++++++++++++++------------ 3 files changed, 108 insertions(+), 34 deletions(-) diff --git a/fs/ext4/ext4.h b/fs/ext4/ext4.h index 6c7924d9e35..38e661b0ea8 100644 --- a/fs/ext4/ext4.h +++ b/fs/ext4/ext4.h @@ -1072,6 +1072,7 @@ extern void ext4_set_inode_flags(struct inode *); extern void ext4_get_inode_flags(struct ext4_inode_info *); extern void ext4_set_aops(struct inode *inode); extern int ext4_writepage_trans_blocks(struct inode *); +extern int ext4_meta_trans_blocks(struct inode *, int nrblocks, int idxblocks); extern int ext4_block_truncate_page(handle_t *handle, struct address_space *mapping, loff_t from); extern int ext4_page_mkwrite(struct vm_area_struct *vma, struct page *page); @@ -1227,6 +1228,8 @@ extern const struct inode_operations ext4_fast_symlink_inode_operations; /* extents.c */ extern int ext4_ext_tree_init(handle_t *handle, struct inode *); extern int ext4_ext_writepage_trans_blocks(struct inode *, int); +extern int ext4_ext_index_trans_blocks(struct inode *inode, int nrblocks, + int chunk); extern int ext4_ext_get_blocks(handle_t *handle, struct inode *inode, ext4_lblk_t iblock, unsigned long max_blocks, struct buffer_head *bh_result, diff --git a/fs/ext4/ext4_jbd2.h b/fs/ext4/ext4_jbd2.h index eb8bc3afe6e..b455c685a98 100644 --- a/fs/ext4/ext4_jbd2.h +++ b/fs/ext4/ext4_jbd2.h @@ -51,6 +51,14 @@ EXT4_XATTR_TRANS_BLOCKS - 2 + \ 2*EXT4_QUOTA_TRANS_BLOCKS(sb)) +/* + * Define the number of metadata blocks we need to account to modify data. + * + * This include super block, inode block, quota blocks and xattr blocks + */ +#define EXT4_META_TRANS_BLOCKS(sb) (EXT4_XATTR_TRANS_BLOCKS + \ + 2*EXT4_QUOTA_TRANS_BLOCKS(sb)) + /* Delete operations potentially hit one directory's namespace plus an * entire inode, plus arbitrary amounts of bitmap/indirection data. Be * generous. We can grow the delete transaction later if necessary. */ diff --git a/fs/ext4/inode.c b/fs/ext4/inode.c index 5e17d5f22a7..a2712906514 100644 --- a/fs/ext4/inode.c +++ b/fs/ext4/inode.c @@ -4354,56 +4354,119 @@ int ext4_getattr(struct vfsmount *mnt, struct dentry *dentry, return 0; } +static int ext4_indirect_trans_blocks(struct inode *inode, int nrblocks, + int chunk) +{ + int indirects; + + /* if nrblocks are contiguous */ + if (chunk) { + /* + * With N contiguous data blocks, it need at most + * N/EXT4_ADDR_PER_BLOCK(inode->i_sb) indirect blocks + * 2 dindirect blocks + * 1 tindirect block + */ + indirects = nrblocks / EXT4_ADDR_PER_BLOCK(inode->i_sb); + return indirects + 3; + } + /* + * if nrblocks are not contiguous, worse case, each block touch + * a indirect block, and each indirect block touch a double indirect + * block, plus a triple indirect block + */ + indirects = nrblocks * 2 + 1; + return indirects; +} + +static int ext4_index_trans_blocks(struct inode *inode, int nrblocks, int chunk) +{ + if (!(EXT4_I(inode)->i_flags & EXT4_EXTENTS_FL)) + return ext4_indirect_trans_blocks(inode, nrblocks, 0); + return ext4_ext_index_trans_blocks(inode, nrblocks, 0); +} /* - * How many blocks doth make a writepage()? + * Account for index blocks, block groups bitmaps and block group + * descriptor blocks if modify datablocks and index blocks + * worse case, the indexs blocks spread over different block groups * - * With N blocks per page, it may be: - * N data blocks - * 2 indirect block - * 2 dindirect - * 1 tindirect - * N+5 bitmap blocks (from the above) - * N+5 group descriptor summary blocks - * 1 inode block - * 1 superblock. - * 2 * EXT4_SINGLEDATA_TRANS_BLOCKS for the quote files + * If datablocks are discontiguous, they are possible to spread over + * different block groups too. If they are contiugous, with flexbg, + * they could still across block group boundary. * - * 3 * (N + 5) + 2 + 2 * EXT4_SINGLEDATA_TRANS_BLOCKS + * Also account for superblock, inode, quota and xattr blocks + */ +int ext4_meta_trans_blocks(struct inode *inode, int nrblocks, int chunk) +{ + int groups, gdpblocks; + int idxblocks; + int ret = 0; + + /* + * How many index blocks need to touch to modify nrblocks? + * The "Chunk" flag indicating whether the nrblocks is + * physically contiguous on disk + * + * For Direct IO and fallocate, they calls get_block to allocate + * one single extent at a time, so they could set the "Chunk" flag + */ + idxblocks = ext4_index_trans_blocks(inode, nrblocks, chunk); + + ret = idxblocks; + + /* + * Now let's see how many group bitmaps and group descriptors need + * to account + */ + groups = idxblocks; + if (chunk) + groups += 1; + else + groups += nrblocks; + + gdpblocks = groups; + if (groups > EXT4_SB(inode->i_sb)->s_groups_count) + groups = EXT4_SB(inode->i_sb)->s_groups_count; + if (groups > EXT4_SB(inode->i_sb)->s_gdb_count) + gdpblocks = EXT4_SB(inode->i_sb)->s_gdb_count; + + /* bitmaps and block group descriptor blocks */ + ret += groups + gdpblocks; + + /* Blocks for super block, inode, quota and xattr blocks */ + ret += EXT4_META_TRANS_BLOCKS(inode->i_sb); + + return ret; +} + +/* + * Calulate the total number of credits to reserve to fit + * the modification of a single pages into a single transaction * - * With ordered or writeback data it's the same, less the N data blocks. + * This could be called via ext4_write_begin() or later + * ext4_da_writepages() in delalyed allocation case. * - * If the inode's direct blocks can hold an integral number of pages then a - * page cannot straddle two indirect blocks, and we can only touch one indirect - * and dindirect block, and the "5" above becomes "3". + * In both case it's possible that we could allocating multiple + * chunks of blocks. We need to consider the worse case, when + * one new block per extent. * - * This still overestimates under most circumstances. If we were to pass the - * start and end offsets in here as well we could do block_to_path() on each - * block and work out the exact number of indirects which are touched. Pah. + * For Direct IO and fallocate, the journal credits reservation + * is based on one single extent allocation, so they could use + * EXT4_DATA_TRANS_BLOCKS to get the needed credit to log a single + * chunk of allocation needs. */ - int ext4_writepage_trans_blocks(struct inode *inode) { int bpp = ext4_journal_blocks_per_page(inode); - int indirects = (EXT4_NDIR_BLOCKS % bpp) ? 5 : 3; int ret; - if (EXT4_I(inode)->i_flags & EXT4_EXTENTS_FL) - return ext4_ext_writepage_trans_blocks(inode, bpp); + ret = ext4_meta_trans_blocks(inode, bpp, 0); + /* Account for data blocks for journalled mode */ if (ext4_should_journal_data(inode)) - ret = 3 * (bpp + indirects) + 2; - else - ret = 2 * (bpp + indirects) + 2; - -#ifdef CONFIG_QUOTA - /* We know that structure was already allocated during DQUOT_INIT so - * we will be updating only the data blocks + inodes */ - ret += 2*EXT4_QUOTA_TRANS_BLOCKS(inode->i_sb); -#endif - + ret += bpp; return ret; } - /* * The caller must have previously called ext4_reserve_inode_write(). * Give this, we know that the caller already has write access to iloc->bh. -- GitLab From ee12b630687d510f6f4b6d4acdc4e267fd4adeda Mon Sep 17 00:00:00 2001 From: Mingming Cao Date: Tue, 19 Aug 2008 22:16:05 -0400 Subject: [PATCH 015/750] ext4: journal credits reservation fixes for extent file writepage This patch modified the writepage/write_begin credit calculation for extent files, to use the credits caculation helper function. The current calculation of how many index/leaf blocks should be accounted is too conservetive, it always considered the worse case, where the tree level is 5, and in the case of multiple chunk allocations, it always assumed no blocks were dirtied in common across the allocations. This path uses the accurate depth of the inode with some extras to calculate the index blocks, and also less conservative in the case of multiple allocation accounting. Signed-off-by: Mingming Cao Reviewed-by: Aneesh Kumar K.V Signed-off-by: "Theodore Ts'o" --- fs/ext4/ext4_extents.h | 4 +- fs/ext4/extents.c | 104 +++++++++++++++++------------------------ fs/ext4/migrate.c | 3 +- 3 files changed, 49 insertions(+), 62 deletions(-) diff --git a/fs/ext4/ext4_extents.h b/fs/ext4/ext4_extents.h index 6c166c0a54b..d33dc56d698 100644 --- a/fs/ext4/ext4_extents.h +++ b/fs/ext4/ext4_extents.h @@ -216,7 +216,9 @@ extern int ext4_ext_calc_metadata_amount(struct inode *inode, int blocks); extern ext4_fsblk_t idx_pblock(struct ext4_extent_idx *); extern void ext4_ext_store_pblock(struct ext4_extent *, ext4_fsblk_t); extern int ext4_extent_tree_init(handle_t *, struct inode *); -extern int ext4_ext_calc_credits_for_insert(struct inode *, struct ext4_ext_path *); +extern int ext4_ext_calc_credits_for_single_extent(struct inode *inode, + int num, + struct ext4_ext_path *path); extern int ext4_ext_try_to_merge(struct inode *inode, struct ext4_ext_path *path, struct ext4_extent *); diff --git a/fs/ext4/extents.c b/fs/ext4/extents.c index 7212947a8ca..5c5dd3a1d65 100644 --- a/fs/ext4/extents.c +++ b/fs/ext4/extents.c @@ -1747,54 +1747,61 @@ static int ext4_ext_rm_idx(handle_t *handle, struct inode *inode, } /* - * ext4_ext_calc_credits_for_insert: - * This routine returns max. credits that the extent tree can consume. - * It should be OK for low-performance paths like ->writepage() - * To allow many writing processes to fit into a single transaction, - * the caller should calculate credits under i_data_sem and - * pass the actual path. + * ext4_ext_calc_credits_for_single_extent: + * This routine returns max. credits that needed to insert an extent + * to the extent tree. + * When pass the actual path, the caller should calculate credits + * under i_data_sem. */ -int ext4_ext_calc_credits_for_insert(struct inode *inode, +int ext4_ext_calc_credits_for_single_extent(struct inode *inode, int num, struct ext4_ext_path *path) { - int depth, needed; - if (path) { + int depth = ext_depth(inode); + int ret; + /* probably there is space in leaf? */ - depth = ext_depth(inode); if (le16_to_cpu(path[depth].p_hdr->eh_entries) - < le16_to_cpu(path[depth].p_hdr->eh_max)) - return 1; - } + < le16_to_cpu(path[depth].p_hdr->eh_max)) { - /* - * given 32-bit logical block (4294967296 blocks), max. tree - * can be 4 levels in depth -- 4 * 340^4 == 53453440000. - * Let's also add one more level for imbalance. - */ - depth = 5; - - /* allocation of new data block(s) */ - needed = 2; + /* + * There are some space in the leaf tree, no + * need to account for leaf block credit + * + * bitmaps and block group descriptor blocks + * and other metadat blocks still need to be + * accounted. + */ + /* 1 one bitmap, 1 block group descriptor */ + ret = 2 + EXT4_META_TRANS_BLOCKS(inode->i_sb); + } + } - /* - * tree can be full, so it would need to grow in depth: - * we need one credit to modify old root, credits for - * new root will be added in split accounting - */ - needed += 1; + return ext4_meta_trans_blocks(inode, num, 1); +} - /* - * Index split can happen, we would need: - * allocate intermediate indexes (bitmap + group) - * + change two blocks at each level, but root (already included) - */ - needed += (depth * 2) + (depth * 2); +/* + * How many index/leaf blocks need to change/allocate to modify nrblocks? + * + * if nrblocks are fit in a single extent (chunk flag is 1), then + * in the worse case, each tree level index/leaf need to be changed + * if the tree split due to insert a new extent, then the old tree + * index/leaf need to be updated too + * + * If the nrblocks are discontiguous, they could cause + * the whole tree split more than once, but this is really rare. + */ +int ext4_ext_index_trans_blocks(struct inode *inode, int num, int chunk) +{ + int index; + int depth = ext_depth(inode); - /* any allocation modifies superblock */ - needed += 1; + if (chunk) + index = depth * 2; + else + index = depth * 3; - return needed; + return index; } static int ext4_remove_blocks(handle_t *handle, struct inode *inode, @@ -1921,9 +1928,7 @@ ext4_ext_rm_leaf(handle_t *handle, struct inode *inode, correct_index = 1; credits += (ext_depth(inode)) + 1; } -#ifdef CONFIG_QUOTA credits += 2 * EXT4_QUOTA_TRANS_BLOCKS(inode->i_sb); -#endif err = ext4_ext_journal_restart(handle, credits); if (err) @@ -2858,27 +2863,6 @@ out_stop: ext4_journal_stop(handle); } -/* - * ext4_ext_writepage_trans_blocks: - * calculate max number of blocks we could modify - * in order to allocate new block for an inode - */ -int ext4_ext_writepage_trans_blocks(struct inode *inode, int num) -{ - int needed; - - needed = ext4_ext_calc_credits_for_insert(inode, NULL); - - /* caller wants to allocate num blocks, but note it includes sb */ - needed = needed * num - (num - 1); - -#ifdef CONFIG_QUOTA - needed += 2 * EXT4_QUOTA_TRANS_BLOCKS(inode->i_sb); -#endif - - return needed; -} - static void ext4_falloc_update_inode(struct inode *inode, int mode, loff_t new_size, int update_ctime) { diff --git a/fs/ext4/migrate.c b/fs/ext4/migrate.c index b9e077ba07e..46fc0b5b12b 100644 --- a/fs/ext4/migrate.c +++ b/fs/ext4/migrate.c @@ -53,7 +53,8 @@ static int finish_range(handle_t *handle, struct inode *inode, * credit. But below we try to not accumalate too much * of them by restarting the journal. */ - needed = ext4_ext_calc_credits_for_insert(inode, path); + needed = ext4_ext_calc_credits_for_single_extent(inode, + lb->last_block - lb->first_block + 1, path); /* * Make sure the credit we accumalated is not really high -- GitLab From f3bd1f3fa8ca7ec70cfd87aa94dc5e1a260901f2 Mon Sep 17 00:00:00 2001 From: Mingming Cao Date: Tue, 19 Aug 2008 22:16:03 -0400 Subject: [PATCH 016/750] ext4: journal credits reservation fixes for DIO, fallocate DIO and fallocate credit calculation is different than writepage, as they do start a new journal right for each call to ext4_get_blocks_wrap(). This patch uses the helper function in DIO and fallocate case, passing a flag indicating that the modified data are contigous thus could account less indirect/index blocks. This patch also fixed the journal credit reservation for direct I/O (DIO). Previously the estimated credits for DIO only was calculated for non-extent files, which was not enough if the file is extent-based. Also fixed was fallocate double-counting credits for modifying the the superblock. Signed-off-by: Mingming Cao Reviewed-by: Aneesh Kumar K.V Signed-off-by: "Theodore Ts'o" --- fs/ext4/ext4.h | 1 + fs/ext4/extents.c | 11 +++++------ fs/ext4/inode.c | 45 ++++++++++++++++++++++++--------------------- 3 files changed, 30 insertions(+), 27 deletions(-) diff --git a/fs/ext4/ext4.h b/fs/ext4/ext4.h index 38e661b0ea8..295003241d3 100644 --- a/fs/ext4/ext4.h +++ b/fs/ext4/ext4.h @@ -1073,6 +1073,7 @@ extern void ext4_get_inode_flags(struct ext4_inode_info *); extern void ext4_set_aops(struct inode *inode); extern int ext4_writepage_trans_blocks(struct inode *); extern int ext4_meta_trans_blocks(struct inode *, int nrblocks, int idxblocks); +extern int ext4_chunk_trans_blocks(struct inode *, int nrblocks); extern int ext4_block_truncate_page(handle_t *handle, struct address_space *mapping, loff_t from); extern int ext4_page_mkwrite(struct vm_area_struct *vma, struct page *page); diff --git a/fs/ext4/extents.c b/fs/ext4/extents.c index 5c5dd3a1d65..5596b70efa2 100644 --- a/fs/ext4/extents.c +++ b/fs/ext4/extents.c @@ -1758,7 +1758,7 @@ int ext4_ext_calc_credits_for_single_extent(struct inode *inode, int num, { if (path) { int depth = ext_depth(inode); - int ret; + int ret = 0; /* probably there is space in leaf? */ if (le16_to_cpu(path[depth].p_hdr->eh_entries) @@ -1777,7 +1777,7 @@ int ext4_ext_calc_credits_for_single_extent(struct inode *inode, int num, } } - return ext4_meta_trans_blocks(inode, num, 1); + return ext4_chunk_trans_blocks(inode, num); } /* @@ -2810,7 +2810,7 @@ void ext4_ext_truncate(struct inode *inode) /* * probably first extent we're gonna free will be last in block */ - err = ext4_writepage_trans_blocks(inode) + 3; + err = ext4_writepage_trans_blocks(inode); handle = ext4_journal_start(inode, err); if (IS_ERR(handle)) return; @@ -2923,10 +2923,9 @@ long ext4_fallocate(struct inode *inode, int mode, loff_t offset, loff_t len) max_blocks = (EXT4_BLOCK_ALIGN(len + offset, blkbits) >> blkbits) - block; /* - * credits to insert 1 extent into extent tree + buffers to be able to - * modify 1 super block, 1 block bitmap and 1 group descriptor. + * credits to insert 1 extent into extent tree */ - credits = EXT4_DATA_TRANS_BLOCKS(inode->i_sb) + 3; + credits = ext4_chunk_trans_blocks(inode, max_blocks); mutex_lock(&inode->i_mutex); retry: while (ret >= 0 && ret < max_blocks) { diff --git a/fs/ext4/inode.c b/fs/ext4/inode.c index a2712906514..ffc95ba4885 100644 --- a/fs/ext4/inode.c +++ b/fs/ext4/inode.c @@ -1044,18 +1044,6 @@ static void ext4_da_update_reserve_space(struct inode *inode, int used) spin_unlock(&EXT4_I(inode)->i_block_reservation_lock); } -/* Maximum number of blocks we map for direct IO at once. */ -#define DIO_MAX_BLOCKS 4096 -/* - * Number of credits we need for writing DIO_MAX_BLOCKS: - * We need sb + group descriptor + bitmap + inode -> 4 - * For B blocks with A block pointers per block we need: - * 1 (triple ind.) + (B/A/A + 2) (doubly ind.) + (B/A + 2) (indirect). - * If we plug in 4096 for B and 256 for A (for 1KB block size), we get 25. - */ -#define DIO_CREDITS 25 - - /* * The ext4_get_blocks_wrap() function try to look up the requested blocks, * and returns if the blocks are already mapped. @@ -1167,19 +1155,23 @@ int ext4_get_blocks_wrap(handle_t *handle, struct inode *inode, sector_t block, return retval; } +/* Maximum number of blocks we map for direct IO at once. */ +#define DIO_MAX_BLOCKS 4096 + static int ext4_get_block(struct inode *inode, sector_t iblock, struct buffer_head *bh_result, int create) { handle_t *handle = ext4_journal_current_handle(); int ret = 0, started = 0; unsigned max_blocks = bh_result->b_size >> inode->i_blkbits; + int dio_credits; if (create && !handle) { /* Direct IO write... */ if (max_blocks > DIO_MAX_BLOCKS) max_blocks = DIO_MAX_BLOCKS; - handle = ext4_journal_start(inode, DIO_CREDITS + - 2 * EXT4_QUOTA_TRANS_BLOCKS(inode->i_sb)); + dio_credits = ext4_chunk_trans_blocks(inode, max_blocks); + handle = ext4_journal_start(inode, dio_credits); if (IS_ERR(handle)) { ret = PTR_ERR(handle); goto out; @@ -2243,7 +2235,7 @@ static int ext4_da_writepage(struct page *page, * for DIO, writepages, and truncate */ #define EXT4_MAX_WRITEBACK_PAGES DIO_MAX_BLOCKS -#define EXT4_MAX_WRITEBACK_CREDITS DIO_CREDITS +#define EXT4_MAX_WRITEBACK_CREDITS 25 static int ext4_da_writepages(struct address_space *mapping, struct writeback_control *wbc) @@ -4441,7 +4433,8 @@ int ext4_meta_trans_blocks(struct inode *inode, int nrblocks, int chunk) /* * Calulate the total number of credits to reserve to fit - * the modification of a single pages into a single transaction + * the modification of a single pages into a single transaction, + * which may include multiple chunks of block allocations. * * This could be called via ext4_write_begin() or later * ext4_da_writepages() in delalyed allocation case. @@ -4449,11 +4442,6 @@ int ext4_meta_trans_blocks(struct inode *inode, int nrblocks, int chunk) * In both case it's possible that we could allocating multiple * chunks of blocks. We need to consider the worse case, when * one new block per extent. - * - * For Direct IO and fallocate, the journal credits reservation - * is based on one single extent allocation, so they could use - * EXT4_DATA_TRANS_BLOCKS to get the needed credit to log a single - * chunk of allocation needs. */ int ext4_writepage_trans_blocks(struct inode *inode) { @@ -4467,6 +4455,21 @@ int ext4_writepage_trans_blocks(struct inode *inode) ret += bpp; return ret; } + +/* + * Calculate the journal credits for a chunk of data modification. + * + * This is called from DIO, fallocate or whoever calling + * ext4_get_blocks_wrap() to map/allocate a chunk of contigous disk blocks. + * + * journal buffers for data blocks are not included here, as DIO + * and fallocate do no need to journal data buffers. + */ +int ext4_chunk_trans_blocks(struct inode *inode, int nrblocks) +{ + return ext4_meta_trans_blocks(inode, nrblocks, 1); +} + /* * The caller must have previously called ext4_reserve_inode_write(). * Give this, we know that the caller already has write access to iloc->bh. -- GitLab From a1d6cc563bfdf1bf2829d3e6ce4d8b774251796b Mon Sep 17 00:00:00 2001 From: "Aneesh Kumar K.V" Date: Tue, 19 Aug 2008 21:55:02 -0400 Subject: [PATCH 017/750] ext4: Rework the ext4_da_writepages() function With the below changes we reserve credit needed to insert only one extent resulting from a call to single get_block. This makes sure we don't take too much journal credits during writeout. We also don't limit the pages to write. That means we loop through the dirty pages building largest possible contiguous block request. Then we issue a single get_block request. We may get less block that we requested. If so we would end up not mapping some of the buffer_heads. That means those buffer_heads are still marked delay. Later in the writepage callback via __mpage_writepage we redirty those pages. We should also not limit/throttle wbc->nr_to_write in the filesystem writepages callback. That cause wrong behaviour in generic_sync_sb_inodes caused by wbc->nr_to_write being <= 0 Signed-off-by: Aneesh Kumar K.V Reviewed-by: Mingming Cao Signed-off-by: "Theodore Ts'o" --- fs/ext4/inode.c | 201 +++++++++++++++++++++++++++--------------------- 1 file changed, 113 insertions(+), 88 deletions(-) diff --git a/fs/ext4/inode.c b/fs/ext4/inode.c index ffc95ba4885..8dd22eade42 100644 --- a/fs/ext4/inode.c +++ b/fs/ext4/inode.c @@ -41,6 +41,8 @@ #include "acl.h" #include "ext4_extents.h" +#define MPAGE_DA_EXTENT_TAIL 0x01 + static inline int ext4_begin_ordered_truncate(struct inode *inode, loff_t new_size) { @@ -1626,11 +1628,13 @@ struct mpage_da_data { unsigned long first_page, next_page; /* extent of pages */ get_block_t *get_block; struct writeback_control *wbc; + int io_done; + long pages_written; }; /* * mpage_da_submit_io - walks through extent of pages and try to write - * them with __mpage_writepage() + * them with writepage() call back * * @mpd->inode: inode * @mpd->first_page: first page of the extent @@ -1645,18 +1649,11 @@ struct mpage_da_data { static int mpage_da_submit_io(struct mpage_da_data *mpd) { struct address_space *mapping = mpd->inode->i_mapping; - struct mpage_data mpd_pp = { - .bio = NULL, - .last_block_in_bio = 0, - .get_block = mpd->get_block, - .use_writepage = 1, - }; int ret = 0, err, nr_pages, i; unsigned long index, end; struct pagevec pvec; BUG_ON(mpd->next_page <= mpd->first_page); - pagevec_init(&pvec, 0); index = mpd->first_page; end = mpd->next_page - 1; @@ -1674,8 +1671,9 @@ static int mpage_da_submit_io(struct mpage_da_data *mpd) break; index++; - err = __mpage_writepage(page, mpd->wbc, &mpd_pp); - + err = mapping->a_ops->writepage(page, mpd->wbc); + if (!err) + mpd->pages_written++; /* * In error case, we have to continue because * remaining pages are still locked @@ -1686,9 +1684,6 @@ static int mpage_da_submit_io(struct mpage_da_data *mpd) } pagevec_release(&pvec); } - if (mpd_pp.bio) - mpage_bio_submit(WRITE, mpd_pp.bio); - return ret; } @@ -1711,7 +1706,7 @@ static void mpage_put_bnr_to_bhs(struct mpage_da_data *mpd, sector_t logical, int blocks = exbh->b_size >> inode->i_blkbits; sector_t pblock = exbh->b_blocknr, cur_logical; struct buffer_head *head, *bh; - unsigned long index, end; + pgoff_t index, end; struct pagevec pvec; int nr_pages, i; @@ -1796,13 +1791,11 @@ static inline void __unmap_underlying_blocks(struct inode *inode, * * The function skips space we know is already mapped to disk blocks. * - * The function ignores errors ->get_block() returns, thus real - * error handling is postponed to __mpage_writepage() */ static void mpage_da_map_blocks(struct mpage_da_data *mpd) { + int err = 0; struct buffer_head *lbh = &mpd->lbh; - int err = 0, remain = lbh->b_size; sector_t next = lbh->b_blocknr; struct buffer_head new; @@ -1812,35 +1805,32 @@ static void mpage_da_map_blocks(struct mpage_da_data *mpd) if (buffer_mapped(lbh) && !buffer_delay(lbh)) return; - while (remain) { - new.b_state = lbh->b_state; - new.b_blocknr = 0; - new.b_size = remain; - err = mpd->get_block(mpd->inode, next, &new, 1); - if (err) { - /* - * Rather than implement own error handling - * here, we just leave remaining blocks - * unallocated and try again with ->writepage() - */ - break; - } - BUG_ON(new.b_size == 0); + new.b_state = lbh->b_state; + new.b_blocknr = 0; + new.b_size = lbh->b_size; - if (buffer_new(&new)) - __unmap_underlying_blocks(mpd->inode, &new); + /* + * If we didn't accumulate anything + * to write simply return + */ + if (!new.b_size) + return; + err = mpd->get_block(mpd->inode, next, &new, 1); + if (err) + return; + BUG_ON(new.b_size == 0); - /* - * If blocks are delayed marked, we need to - * put actual blocknr and drop delayed bit - */ - if (buffer_delay(lbh) || buffer_unwritten(lbh)) - mpage_put_bnr_to_bhs(mpd, next, &new); + if (buffer_new(&new)) + __unmap_underlying_blocks(mpd->inode, &new); - /* go for the remaining blocks */ - next += new.b_size >> mpd->inode->i_blkbits; - remain -= new.b_size; - } + /* + * If blocks are delayed marked, we need to + * put actual blocknr and drop delayed bit + */ + if (buffer_delay(lbh) || buffer_unwritten(lbh)) + mpage_put_bnr_to_bhs(mpd, next, &new); + + return; } #define BH_FLAGS ((1 << BH_Uptodate) | (1 << BH_Mapped) | \ @@ -1886,13 +1876,9 @@ static void mpage_add_bh_to_extent(struct mpage_da_data *mpd, * need to flush current extent and start new one */ mpage_da_map_blocks(mpd); - - /* - * Now start a new extent - */ - lbh->b_size = bh->b_size; - lbh->b_state = bh->b_state & BH_FLAGS; - lbh->b_blocknr = logical; + mpage_da_submit_io(mpd); + mpd->io_done = 1; + return; } /* @@ -1912,17 +1898,35 @@ static int __mpage_da_writepage(struct page *page, struct buffer_head *bh, *head, fake; sector_t logical; + if (mpd->io_done) { + /* + * Rest of the page in the page_vec + * redirty then and skip then. We will + * try to to write them again after + * starting a new transaction + */ + redirty_page_for_writepage(wbc, page); + unlock_page(page); + return MPAGE_DA_EXTENT_TAIL; + } /* * Can we merge this page to current extent? */ if (mpd->next_page != page->index) { /* * Nope, we can't. So, we map non-allocated blocks - * and start IO on them using __mpage_writepage() + * and start IO on them using writepage() */ if (mpd->next_page != mpd->first_page) { mpage_da_map_blocks(mpd); mpage_da_submit_io(mpd); + /* + * skip rest of the page in the page_vec + */ + mpd->io_done = 1; + redirty_page_for_writepage(wbc, page); + unlock_page(page); + return MPAGE_DA_EXTENT_TAIL; } /* @@ -1953,6 +1957,8 @@ static int __mpage_da_writepage(struct page *page, set_buffer_dirty(bh); set_buffer_uptodate(bh); mpage_add_bh_to_extent(mpd, logical, bh); + if (mpd->io_done) + return MPAGE_DA_EXTENT_TAIL; } else { /* * Page with regular buffer heads, just add all dirty ones @@ -1961,8 +1967,12 @@ static int __mpage_da_writepage(struct page *page, bh = head; do { BUG_ON(buffer_locked(bh)); - if (buffer_dirty(bh)) + if (buffer_dirty(bh) && + (!buffer_mapped(bh) || buffer_delay(bh))) { mpage_add_bh_to_extent(mpd, logical, bh); + if (mpd->io_done) + return MPAGE_DA_EXTENT_TAIL; + } logical++; } while ((bh = bh->b_this_page) != head); } @@ -1981,22 +1991,13 @@ static int __mpage_da_writepage(struct page *page, * * This is a library function, which implements the writepages() * address_space_operation. - * - * In order to avoid duplication of logic that deals with partial pages, - * multiple bio per page, etc, we find non-allocated blocks, allocate - * them with minimal calls to ->get_block() and re-use __mpage_writepage() - * - * It's important that we call __mpage_writepage() only once for each - * involved page, otherwise we'd have to implement more complicated logic - * to deal with pages w/o PG_lock or w/ PG_writeback and so on. - * - * See comments to mpage_writepages() */ static int mpage_da_writepages(struct address_space *mapping, struct writeback_control *wbc, get_block_t get_block) { struct mpage_da_data mpd; + long to_write; int ret; if (!get_block) @@ -2010,17 +2011,22 @@ static int mpage_da_writepages(struct address_space *mapping, mpd.first_page = 0; mpd.next_page = 0; mpd.get_block = get_block; + mpd.io_done = 0; + mpd.pages_written = 0; + + to_write = wbc->nr_to_write; ret = write_cache_pages(mapping, wbc, __mpage_da_writepage, &mpd); /* * Handle last extent of pages */ - if (mpd.next_page != mpd.first_page) { + if (!mpd.io_done && mpd.next_page != mpd.first_page) { mpage_da_map_blocks(&mpd); mpage_da_submit_io(&mpd); } + wbc->nr_to_write = to_write - mpd.pages_written; return ret; } @@ -2238,7 +2244,7 @@ static int ext4_da_writepage(struct page *page, #define EXT4_MAX_WRITEBACK_CREDITS 25 static int ext4_da_writepages(struct address_space *mapping, - struct writeback_control *wbc) + struct writeback_control *wbc) { struct inode *inode = mapping->host; handle_t *handle = NULL; @@ -2246,42 +2252,53 @@ static int ext4_da_writepages(struct address_space *mapping, int ret = 0; long to_write; loff_t range_start = 0; + long pages_skipped = 0; /* * No pages to write? This is mainly a kludge to avoid starting * a transaction for special inodes like journal inode on last iput() * because that could violate lock ordering on umount */ - if (!mapping->nrpages) + if (!mapping->nrpages || !mapping_tagged(mapping, PAGECACHE_TAG_DIRTY)) return 0; - /* - * Estimate the worse case needed credits to write out - * EXT4_MAX_BUF_BLOCKS pages - */ - needed_blocks = EXT4_MAX_WRITEBACK_CREDITS; - - to_write = wbc->nr_to_write; - if (!wbc->range_cyclic) { + if (!wbc->range_cyclic) /* * If range_cyclic is not set force range_cont * and save the old writeback_index */ wbc->range_cont = 1; - range_start = wbc->range_start; - } - while (!ret && to_write) { + range_start = wbc->range_start; + pages_skipped = wbc->pages_skipped; + +restart_loop: + to_write = wbc->nr_to_write; + while (!ret && to_write > 0) { + + /* + * we insert one extent at a time. So we need + * credit needed for single extent allocation. + * journalled mode is currently not supported + * by delalloc + */ + BUG_ON(ext4_should_journal_data(inode)); + needed_blocks = EXT4_DATA_TRANS_BLOCKS(inode->i_sb); + /* start a new transaction*/ handle = ext4_journal_start(inode, needed_blocks); if (IS_ERR(handle)) { ret = PTR_ERR(handle); + printk(KERN_EMERG "%s: jbd2_start: " + "%ld pages, ino %lu; err %d\n", __func__, + wbc->nr_to_write, inode->i_ino, ret); + dump_stack(); goto out_writepages; } if (ext4_should_order_data(inode)) { /* * With ordered mode we need to add - * the inode to the journal handle + * the inode to the journal handl * when we do block allocation. */ ret = ext4_jbd2_file_inode(handle, inode); @@ -2289,20 +2306,20 @@ static int ext4_da_writepages(struct address_space *mapping, ext4_journal_stop(handle); goto out_writepages; } - } - /* - * set the max dirty pages could be write at a time - * to fit into the reserved transaction credits - */ - if (wbc->nr_to_write > EXT4_MAX_WRITEBACK_PAGES) - wbc->nr_to_write = EXT4_MAX_WRITEBACK_PAGES; to_write -= wbc->nr_to_write; ret = mpage_da_writepages(mapping, wbc, - ext4_da_get_block_write); + ext4_da_get_block_write); ext4_journal_stop(handle); - if (wbc->nr_to_write) { + if (ret == MPAGE_DA_EXTENT_TAIL) { + /* + * got one extent now try with + * rest of the pages + */ + to_write += wbc->nr_to_write; + ret = 0; + } else if (wbc->nr_to_write) { /* * There is no more writeout needed * or we requested for a noblocking writeout @@ -2314,10 +2331,18 @@ static int ext4_da_writepages(struct address_space *mapping, wbc->nr_to_write = to_write; } + if (wbc->range_cont && (pages_skipped != wbc->pages_skipped)) { + /* We skipped pages in this loop */ + wbc->range_start = range_start; + wbc->nr_to_write = to_write + + wbc->pages_skipped - pages_skipped; + wbc->pages_skipped = pages_skipped; + goto restart_loop; + } + out_writepages: wbc->nr_to_write = to_write; - if (range_start) - wbc->range_start = range_start; + wbc->range_start = range_start; return ret; } -- GitLab From 525f4ed8dcb72c71b306a78ecbf06f41d08fe441 Mon Sep 17 00:00:00 2001 From: Mingming Cao Date: Tue, 19 Aug 2008 22:15:58 -0400 Subject: [PATCH 018/750] ext4: journal credit fix for the delayed allocation's writepages() function Previous delalloc writepages implementation started a new transaction outside of a loop which called get_block() to do the block allocation. Since we didn't know exactly how many blocks would need to be allocated, the estimated journal credits required was very conservative and caused many issues. With the reworked delayed allocation, a new transaction is created for each get_block(), thus we don't need to guess how many credits for the multiple chunk of allocation. We start every transaction with enough credits for inserting a single exent. When estimate the credits for indirect blocks to allocate a chunk of blocks, we need to know the number of data blocks to allocate. We use the total number of reserved delalloc datablocks; if that is too big, for non-extent files, we need to limit the number of blocks to EXT4_MAX_TRANS_BLOCKS. Code cleanup from Aneesh. Signed-off-by: Mingming Cao Reviewed-off-by: Aneesh Kumar K.V Signed-off-by: "Theodore Ts'o" --- fs/ext4/extents.c | 8 ++--- fs/ext4/inode.c | 74 ++++++++++++++++++++++++++++++++++------------- 2 files changed, 58 insertions(+), 24 deletions(-) diff --git a/fs/ext4/extents.c b/fs/ext4/extents.c index 5596b70efa2..b24d3c53f20 100644 --- a/fs/ext4/extents.c +++ b/fs/ext4/extents.c @@ -1753,7 +1753,7 @@ static int ext4_ext_rm_idx(handle_t *handle, struct inode *inode, * When pass the actual path, the caller should calculate credits * under i_data_sem. */ -int ext4_ext_calc_credits_for_single_extent(struct inode *inode, int num, +int ext4_ext_calc_credits_for_single_extent(struct inode *inode, int nrblocks, struct ext4_ext_path *path) { if (path) { @@ -1772,12 +1772,12 @@ int ext4_ext_calc_credits_for_single_extent(struct inode *inode, int num, * and other metadat blocks still need to be * accounted. */ - /* 1 one bitmap, 1 block group descriptor */ + /* 1 bitmap, 1 block group descriptor */ ret = 2 + EXT4_META_TRANS_BLOCKS(inode->i_sb); } } - return ext4_chunk_trans_blocks(inode, num); + return ext4_chunk_trans_blocks(inode, nrblocks); } /* @@ -1791,7 +1791,7 @@ int ext4_ext_calc_credits_for_single_extent(struct inode *inode, int num, * If the nrblocks are discontiguous, they could cause * the whole tree split more than once, but this is really rare. */ -int ext4_ext_index_trans_blocks(struct inode *inode, int num, int chunk) +int ext4_ext_index_trans_blocks(struct inode *inode, int nrblocks, int chunk) { int index; int depth = ext_depth(inode); diff --git a/fs/ext4/inode.c b/fs/ext4/inode.c index 8dd22eade42..d1906d9a22d 100644 --- a/fs/ext4/inode.c +++ b/fs/ext4/inode.c @@ -1848,29 +1848,53 @@ static void mpage_da_map_blocks(struct mpage_da_data *mpd) static void mpage_add_bh_to_extent(struct mpage_da_data *mpd, sector_t logical, struct buffer_head *bh) { - struct buffer_head *lbh = &mpd->lbh; sector_t next; + size_t b_size = bh->b_size; + struct buffer_head *lbh = &mpd->lbh; + int nrblocks = lbh->b_size >> mpd->inode->i_blkbits; - next = lbh->b_blocknr + (lbh->b_size >> mpd->inode->i_blkbits); - + /* check if thereserved journal credits might overflow */ + if (!(EXT4_I(mpd->inode)->i_flags & EXT4_EXTENTS_FL)) { + if (nrblocks >= EXT4_MAX_TRANS_DATA) { + /* + * With non-extent format we are limited by the journal + * credit available. Total credit needed to insert + * nrblocks contiguous blocks is dependent on the + * nrblocks. So limit nrblocks. + */ + goto flush_it; + } else if ((nrblocks + (b_size >> mpd->inode->i_blkbits)) > + EXT4_MAX_TRANS_DATA) { + /* + * Adding the new buffer_head would make it cross the + * allowed limit for which we have journal credit + * reserved. So limit the new bh->b_size + */ + b_size = (EXT4_MAX_TRANS_DATA - nrblocks) << + mpd->inode->i_blkbits; + /* we will do mpage_da_submit_io in the next loop */ + } + } /* * First block in the extent */ if (lbh->b_size == 0) { lbh->b_blocknr = logical; - lbh->b_size = bh->b_size; + lbh->b_size = b_size; lbh->b_state = bh->b_state & BH_FLAGS; return; } + next = lbh->b_blocknr + nrblocks; /* * Can we merge the block to our big extent? */ if (logical == next && (bh->b_state & BH_FLAGS) == lbh->b_state) { - lbh->b_size += bh->b_size; + lbh->b_size += b_size; return; } +flush_it: /* * We couldn't merge the block to our extent, so we * need to flush current extent and start new one @@ -2231,17 +2255,29 @@ static int ext4_da_writepage(struct page *page, } /* - * For now just follow the DIO way to estimate the max credits - * needed to write out EXT4_MAX_WRITEBACK_PAGES. - * todo: need to calculate the max credits need for - * extent based files, currently the DIO credits is based on - * indirect-blocks mapping way. - * - * Probably should have a generic way to calculate credits - * for DIO, writepages, and truncate + * This is called via ext4_da_writepages() to + * calulate the total number of credits to reserve to fit + * a single extent allocation into a single transaction, + * ext4_da_writpeages() will loop calling this before + * the block allocation. */ -#define EXT4_MAX_WRITEBACK_PAGES DIO_MAX_BLOCKS -#define EXT4_MAX_WRITEBACK_CREDITS 25 + +static int ext4_da_writepages_trans_blocks(struct inode *inode) +{ + int max_blocks = EXT4_I(inode)->i_reserved_data_blocks; + + /* + * With non-extent format the journal credit needed to + * insert nrblocks contiguous block is dependent on + * number of contiguous block. So we will limit + * number of contiguous block to a sane value + */ + if (!(inode->i_flags & EXT4_EXTENTS_FL) && + (max_blocks > EXT4_MAX_TRANS_DATA)) + max_blocks = EXT4_MAX_TRANS_DATA; + + return ext4_chunk_trans_blocks(inode, max_blocks); +} static int ext4_da_writepages(struct address_space *mapping, struct writeback_control *wbc) @@ -2283,7 +2319,7 @@ restart_loop: * by delalloc */ BUG_ON(ext4_should_journal_data(inode)); - needed_blocks = EXT4_DATA_TRANS_BLOCKS(inode->i_sb); + needed_blocks = ext4_da_writepages_trans_blocks(inode); /* start a new transaction*/ handle = ext4_journal_start(inode, needed_blocks); @@ -4461,11 +4497,9 @@ int ext4_meta_trans_blocks(struct inode *inode, int nrblocks, int chunk) * the modification of a single pages into a single transaction, * which may include multiple chunks of block allocations. * - * This could be called via ext4_write_begin() or later - * ext4_da_writepages() in delalyed allocation case. + * This could be called via ext4_write_begin() * - * In both case it's possible that we could allocating multiple - * chunks of blocks. We need to consider the worse case, when + * We need to consider the worse case, when * one new block per extent. */ int ext4_writepage_trans_blocks(struct inode *inode) -- GitLab From 16eb72956496594d023a7d7cd14a86404ad195ad Mon Sep 17 00:00:00 2001 From: "Aneesh Kumar K.V" Date: Tue, 19 Aug 2008 21:16:54 -0400 Subject: [PATCH 019/750] ext4: make sure ext4_has_free_blocks returns 0 for ENOSPC Fix ext4_has_free_blocks() to return 0 when we don't have enough space. Signed-off-by: Aneesh Kumar K.V Signed-off-by: Mingming Cao Signed-off-by: "Theodore Ts'o" --- fs/ext4/balloc.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/fs/ext4/balloc.c b/fs/ext4/balloc.c index 1ae5004e93f..e9fa960ba6d 100644 --- a/fs/ext4/balloc.c +++ b/fs/ext4/balloc.c @@ -1626,6 +1626,9 @@ ext4_fsblk_t ext4_has_free_blocks(struct ext4_sb_info *sbi, free_blocks = percpu_counter_sum_and_set(&sbi->s_freeblocks_counter); #endif + if (free_blocks <= root_blocks) + /* we don't have free space */ + return 0; if (free_blocks - root_blocks < nblocks) return free_blocks - root_blocks; return nblocks; -- GitLab From 91246c009094142f95ecc7573b7caed2bcef52c7 Mon Sep 17 00:00:00 2001 From: "Aneesh Kumar K.V" Date: Tue, 19 Aug 2008 21:14:52 -0400 Subject: [PATCH 020/750] ext4: Initialize writeback_index to 0 when allocating a new inode The write_cache_pages() function uses the mapping->writeback_index as the starting index to write out when range_cyclic is set. Properly initialize writeback_index so that we start the writeout at index 0. This was found when debugging the small file fragmentation on ext4. Signed-off-by: Aneesh Kumar K.V Signed-off-by: "Theodore Ts'o" --- fs/ext4/super.c | 1 + 1 file changed, 1 insertion(+) diff --git a/fs/ext4/super.c b/fs/ext4/super.c index d5d77958b86..566344b926b 100644 --- a/fs/ext4/super.c +++ b/fs/ext4/super.c @@ -568,6 +568,7 @@ static struct inode *ext4_alloc_inode(struct super_block *sb) #endif ei->i_block_alloc_info = NULL; ei->vfs_inode.i_version = 1; + ei->vfs_inode.i_data.writeback_index = 0; memset(&ei->i_cached_extent, 0, sizeof(struct ext4_ext_cache)); INIT_LIST_HEAD(&ei->i_prealloc_list); spin_lock_init(&ei->i_prealloc_lock); -- GitLab From 5e745b041f2ccad63077118b40468521306f3962 Mon Sep 17 00:00:00 2001 From: "Aneesh Kumar K.V" Date: Mon, 18 Aug 2008 18:00:57 -0400 Subject: [PATCH 021/750] ext4: Fix small file fragmentation For small file block allocations, mballoc uses per cpu prealloc space. Use goal block when searching for the right prealloc space. Also make sure ext4_da_writepages tries to write all the pages for small files in single attempt Signed-off-by: Aneesh Kumar K.V Signed-off-by: "Theodore Ts'o" --- fs/ext4/inode.c | 21 +++++++++++++------ fs/ext4/mballoc.c | 53 ++++++++++++++++++++++++++++++++++++++++------- 2 files changed, 61 insertions(+), 13 deletions(-) diff --git a/fs/ext4/inode.c b/fs/ext4/inode.c index d1906d9a22d..7e91913e325 100644 --- a/fs/ext4/inode.c +++ b/fs/ext4/inode.c @@ -2282,13 +2282,12 @@ static int ext4_da_writepages_trans_blocks(struct inode *inode) static int ext4_da_writepages(struct address_space *mapping, struct writeback_control *wbc) { - struct inode *inode = mapping->host; handle_t *handle = NULL; - int needed_blocks; - int ret = 0; - long to_write; loff_t range_start = 0; - long pages_skipped = 0; + struct inode *inode = mapping->host; + int needed_blocks, ret = 0, nr_to_writebump = 0; + long to_write, pages_skipped = 0; + struct ext4_sb_info *sbi = EXT4_SB(mapping->host->i_sb); /* * No pages to write? This is mainly a kludge to avoid starting @@ -2297,6 +2296,16 @@ static int ext4_da_writepages(struct address_space *mapping, */ if (!mapping->nrpages || !mapping_tagged(mapping, PAGECACHE_TAG_DIRTY)) return 0; + /* + * Make sure nr_to_write is >= sbi->s_mb_stream_request + * This make sure small files blocks are allocated in + * single attempt. This ensure that small files + * get less fragmented. + */ + if (wbc->nr_to_write < sbi->s_mb_stream_request) { + nr_to_writebump = sbi->s_mb_stream_request - wbc->nr_to_write; + wbc->nr_to_write = sbi->s_mb_stream_request; + } if (!wbc->range_cyclic) /* @@ -2377,7 +2386,7 @@ restart_loop: } out_writepages: - wbc->nr_to_write = to_write; + wbc->nr_to_write = to_write - nr_to_writebump; wbc->range_start = range_start; return ret; } diff --git a/fs/ext4/mballoc.c b/fs/ext4/mballoc.c index 865e9ddb44d..e0e3a5eb1dd 100644 --- a/fs/ext4/mballoc.c +++ b/fs/ext4/mballoc.c @@ -3281,6 +3281,35 @@ static void ext4_mb_use_group_pa(struct ext4_allocation_context *ac, mb_debug("use %u/%u from group pa %p\n", pa->pa_lstart-len, len, pa); } +/* + * Return the prealloc space that have minimal distance + * from the goal block. @cpa is the prealloc + * space that is having currently known minimal distance + * from the goal block. + */ +static struct ext4_prealloc_space * +ext4_mb_check_group_pa(ext4_fsblk_t goal_block, + struct ext4_prealloc_space *pa, + struct ext4_prealloc_space *cpa) +{ + ext4_fsblk_t cur_distance, new_distance; + + if (cpa == NULL) { + atomic_inc(&pa->pa_count); + return pa; + } + cur_distance = abs(goal_block - cpa->pa_pstart); + new_distance = abs(goal_block - pa->pa_pstart); + + if (cur_distance < new_distance) + return cpa; + + /* drop the previous reference */ + atomic_dec(&cpa->pa_count); + atomic_inc(&pa->pa_count); + return pa; +} + /* * search goal blocks in preallocated space */ @@ -3290,7 +3319,8 @@ ext4_mb_use_preallocated(struct ext4_allocation_context *ac) int order, i; struct ext4_inode_info *ei = EXT4_I(ac->ac_inode); struct ext4_locality_group *lg; - struct ext4_prealloc_space *pa; + struct ext4_prealloc_space *pa, *cpa = NULL; + ext4_fsblk_t goal_block; /* only data can be preallocated */ if (!(ac->ac_flags & EXT4_MB_HINT_DATA)) @@ -3333,6 +3363,13 @@ ext4_mb_use_preallocated(struct ext4_allocation_context *ac) /* The max size of hash table is PREALLOC_TB_SIZE */ order = PREALLOC_TB_SIZE - 1; + goal_block = ac->ac_g_ex.fe_group * EXT4_BLOCKS_PER_GROUP(ac->ac_sb) + + ac->ac_g_ex.fe_start + + le32_to_cpu(EXT4_SB(ac->ac_sb)->s_es->s_first_data_block); + /* + * search for the prealloc space that is having + * minimal distance from the goal block. + */ for (i = order; i < PREALLOC_TB_SIZE; i++) { rcu_read_lock(); list_for_each_entry_rcu(pa, &lg->lg_prealloc_list[i], @@ -3340,17 +3377,19 @@ ext4_mb_use_preallocated(struct ext4_allocation_context *ac) spin_lock(&pa->pa_lock); if (pa->pa_deleted == 0 && pa->pa_free >= ac->ac_o_ex.fe_len) { - atomic_inc(&pa->pa_count); - ext4_mb_use_group_pa(ac, pa); - spin_unlock(&pa->pa_lock); - ac->ac_criteria = 20; - rcu_read_unlock(); - return 1; + + cpa = ext4_mb_check_group_pa(goal_block, + pa, cpa); } spin_unlock(&pa->pa_lock); } rcu_read_unlock(); } + if (cpa) { + ext4_mb_use_group_pa(ac, cpa); + ac->ac_criteria = 20; + return 1; + } return 0; } -- GitLab From 4537398d91e6e03811ba971d959b762137058c1a Mon Sep 17 00:00:00 2001 From: Theodore Ts'o Date: Sun, 27 Jul 2008 19:59:21 -0400 Subject: [PATCH 022/750] ext4: Update documentation to remind users to update mke2fs.conf Signed-off-by: "Theodore Ts'o" --- Documentation/filesystems/ext4.txt | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/Documentation/filesystems/ext4.txt b/Documentation/filesystems/ext4.txt index 80e193d82e2..0d5394920a3 100644 --- a/Documentation/filesystems/ext4.txt +++ b/Documentation/filesystems/ext4.txt @@ -26,6 +26,12 @@ Mailing list: linux-ext4@vger.kernel.org git://git.kernel.org/pub/scm/fs/ext2/e2fsprogs.git + - Note that it is highly important to install the mke2fs.conf file + that comes with the e2fsprogs 1.41.x sources in /etc/mke2fs.conf. If + you have edited the /etc/mke2fs.conf file installed on your system, + you will need to merge your changes with the version from e2fsprogs + 1.41.x. + - Create a new filesystem using the ext4dev filesystem type: # mke2fs -t ext4dev /dev/hda1 -- GitLab From 8cb22bcb1f3ef70d4d48092e9b057175ad9ec78d Mon Sep 17 00:00:00 2001 From: Mark Langsdorf Date: Fri, 18 Jul 2008 16:03:52 -0500 Subject: [PATCH 023/750] x86: L3 cache index disable for 2.6.26 New versions of AMD processors have support to disable parts of their L3 caches if too many MCEs are generated by the L3 cache. This patch provides a /sysfs interface under the cache hierarchy to display which caches indices are disabled (if any) and to monitoring applications to disable a cache index. This patch does not set an automatic policy to disable the L3 cache. Policy decisions would need to be made by a RAS handler. This patch merely makes it easier to see what indices are currently disabled. Signed-off-by: Mark Langsdorf Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/intel_cacheinfo.c | 87 +++++++++++++++++++++++++-- 1 file changed, 81 insertions(+), 6 deletions(-) diff --git a/arch/x86/kernel/cpu/intel_cacheinfo.c b/arch/x86/kernel/cpu/intel_cacheinfo.c index ff517f0b8cc..d6ea50e270e 100644 --- a/arch/x86/kernel/cpu/intel_cacheinfo.c +++ b/arch/x86/kernel/cpu/intel_cacheinfo.c @@ -16,6 +16,7 @@ #include #include +#include #define LVL_1_INST 1 #define LVL_1_DATA 2 @@ -130,6 +131,7 @@ struct _cpuid4_info { union _cpuid4_leaf_ebx ebx; union _cpuid4_leaf_ecx ecx; unsigned long size; + unsigned long can_disable; cpumask_t shared_cpu_map; /* future?: only cpus/node is needed */ }; @@ -251,6 +253,13 @@ static void __cpuinit amd_cpuid4(int leaf, union _cpuid4_leaf_eax *eax, (ebx->split.ways_of_associativity + 1) - 1; } +static void __cpuinit amd_check_l3_disable(int index, struct _cpuid4_info *this_leaf) +{ + if (index < 3) + return; + this_leaf->can_disable = 1; +} + static int __cpuinit cpuid4_cache_lookup(int index, struct _cpuid4_info *this_leaf) { union _cpuid4_leaf_eax eax; @@ -258,9 +267,12 @@ static int __cpuinit cpuid4_cache_lookup(int index, struct _cpuid4_info *this_le union _cpuid4_leaf_ecx ecx; unsigned edx; - if (boot_cpu_data.x86_vendor == X86_VENDOR_AMD) + if (boot_cpu_data.x86_vendor == X86_VENDOR_AMD) { amd_cpuid4(index, &eax, &ebx, &ecx); - else + if (boot_cpu_data.x86 >= 0x10) + amd_check_l3_disable(index, this_leaf); + + } else cpuid_count(4, index, &eax.full, &ebx.full, &ecx.full, &edx); if (eax.split.type == CACHE_TYPE_NULL) return -EIO; /* better error ? */ @@ -637,6 +649,61 @@ static ssize_t show_type(struct _cpuid4_info *this_leaf, char *buf) { } } +#define to_object(k) container_of(k, struct _index_kobject, kobj) +#define to_attr(a) container_of(a, struct _cache_attr, attr) + +static ssize_t show_cache_disable(struct _cpuid4_info *this_leaf, char *buf) +{ + struct pci_dev *dev; + if (this_leaf->can_disable) { + int i; + ssize_t ret = 0; + int node = cpu_to_node(first_cpu(this_leaf->shared_cpu_map)); + dev = k8_northbridges[node]; + + for (i = 0; i < 2; i++) { + unsigned int reg; + pci_read_config_dword(dev, 0x1BC + i * 4, ®); + ret += sprintf(buf, "%sEntry: %d\n", buf, i); + ret += sprintf(buf, "%sReads: %s\tNew Entries: %s\n", + buf, + reg & 0x80000000 ? "Disabled" : "Allowed", + reg & 0x40000000 ? "Disabled" : "Allowed"); + ret += sprintf(buf, "%sSubCache: %x\tIndex: %x\n", buf, + (reg & 0x30000) >> 16, reg & 0xfff); + + } + return ret; + } + return sprintf(buf, "Feature not enabled\n"); +} + +static ssize_t store_cache_disable(struct _cpuid4_info *this_leaf, const char *buf, size_t count) +{ + struct pci_dev *dev; + if (this_leaf->can_disable) { + /* write the MSR value */ + unsigned int ret; + unsigned int index, val; + int node = cpu_to_node(first_cpu(this_leaf->shared_cpu_map)); + dev = k8_northbridges[node]; + + if (strlen(buf) > 15) + return -EINVAL; + ret = sscanf(buf, "%x %x", &index, &val); + if (ret != 2) + return -EINVAL; + if (index > 1) + return -EINVAL; + val |= 0xc0000000; + pci_write_config_dword(dev, 0x1BC + index * 4, val & ~0x40000000); + wbinvd(); + pci_write_config_dword(dev, 0x1BC + index * 4, val); + return 1; + } + return 0; +} + struct _cache_attr { struct attribute attr; ssize_t (*show)(struct _cpuid4_info *, char *); @@ -657,6 +724,8 @@ define_one_ro(size); define_one_ro(shared_cpu_map); define_one_ro(shared_cpu_list); +static struct _cache_attr cache_disable = __ATTR(cache_disable, 0644, show_cache_disable, store_cache_disable); + static struct attribute * default_attrs[] = { &type.attr, &level.attr, @@ -667,12 +736,10 @@ static struct attribute * default_attrs[] = { &size.attr, &shared_cpu_map.attr, &shared_cpu_list.attr, + &cache_disable.attr, NULL }; -#define to_object(k) container_of(k, struct _index_kobject, kobj) -#define to_attr(a) container_of(a, struct _cache_attr, attr) - static ssize_t show(struct kobject * kobj, struct attribute * attr, char * buf) { struct _cache_attr *fattr = to_attr(attr); @@ -689,7 +756,15 @@ static ssize_t show(struct kobject * kobj, struct attribute * attr, char * buf) static ssize_t store(struct kobject * kobj, struct attribute * attr, const char * buf, size_t count) { - return 0; + struct _cache_attr *fattr = to_attr(attr); + struct _index_kobject *this_leaf = to_object(kobj); + ssize_t ret; + + ret = fattr->store ? + fattr->store(CPUID4_INFO_IDX(this_leaf->cpu, this_leaf->index), + buf, count) : + 0; + return ret; } static struct sysfs_ops sysfs_ops = { -- GitLab From 7a4983bb5f94f6521aa3236fe5c035cf9bef543f Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Mon, 21 Jul 2008 13:34:21 +0200 Subject: [PATCH 024/750] x86: L3 cache index disable for 2.6.26, cleanups No change in functionality. Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/intel_cacheinfo.c | 115 ++++++++++++++------------ 1 file changed, 61 insertions(+), 54 deletions(-) diff --git a/arch/x86/kernel/cpu/intel_cacheinfo.c b/arch/x86/kernel/cpu/intel_cacheinfo.c index d6ea50e270e..a61c9e399ba 100644 --- a/arch/x86/kernel/cpu/intel_cacheinfo.c +++ b/arch/x86/kernel/cpu/intel_cacheinfo.c @@ -253,14 +253,16 @@ static void __cpuinit amd_cpuid4(int leaf, union _cpuid4_leaf_eax *eax, (ebx->split.ways_of_associativity + 1) - 1; } -static void __cpuinit amd_check_l3_disable(int index, struct _cpuid4_info *this_leaf) +static void __cpuinit +amd_check_l3_disable(int index, struct _cpuid4_info *this_leaf) { if (index < 3) return; this_leaf->can_disable = 1; } -static int __cpuinit cpuid4_cache_lookup(int index, struct _cpuid4_info *this_leaf) +static int +__cpuinit cpuid4_cache_lookup(int index, struct _cpuid4_info *this_leaf) { union _cpuid4_leaf_eax eax; union _cpuid4_leaf_ebx ebx; @@ -271,19 +273,20 @@ static int __cpuinit cpuid4_cache_lookup(int index, struct _cpuid4_info *this_le amd_cpuid4(index, &eax, &ebx, &ecx); if (boot_cpu_data.x86 >= 0x10) amd_check_l3_disable(index, this_leaf); - - } else - cpuid_count(4, index, &eax.full, &ebx.full, &ecx.full, &edx); + } else { + cpuid_count(4, index, &eax.full, &ebx.full, &ecx.full, &edx); + } + if (eax.split.type == CACHE_TYPE_NULL) return -EIO; /* better error ? */ this_leaf->eax = eax; this_leaf->ebx = ebx; this_leaf->ecx = ecx; - this_leaf->size = (ecx.split.number_of_sets + 1) * - (ebx.split.coherency_line_size + 1) * - (ebx.split.physical_line_partition + 1) * - (ebx.split.ways_of_associativity + 1); + this_leaf->size = (ecx.split.number_of_sets + 1) * + (ebx.split.coherency_line_size + 1) * + (ebx.split.physical_line_partition + 1) * + (ebx.split.ways_of_associativity + 1); return 0; } @@ -649,59 +652,63 @@ static ssize_t show_type(struct _cpuid4_info *this_leaf, char *buf) { } } -#define to_object(k) container_of(k, struct _index_kobject, kobj) -#define to_attr(a) container_of(a, struct _cache_attr, attr) +#define to_object(k) container_of(k, struct _index_kobject, kobj) +#define to_attr(a) container_of(a, struct _cache_attr, attr) static ssize_t show_cache_disable(struct _cpuid4_info *this_leaf, char *buf) { - struct pci_dev *dev; - if (this_leaf->can_disable) { - int i; - ssize_t ret = 0; - int node = cpu_to_node(first_cpu(this_leaf->shared_cpu_map)); - dev = k8_northbridges[node]; - - for (i = 0; i < 2; i++) { - unsigned int reg; - pci_read_config_dword(dev, 0x1BC + i * 4, ®); - ret += sprintf(buf, "%sEntry: %d\n", buf, i); - ret += sprintf(buf, "%sReads: %s\tNew Entries: %s\n", - buf, - reg & 0x80000000 ? "Disabled" : "Allowed", - reg & 0x40000000 ? "Disabled" : "Allowed"); - ret += sprintf(buf, "%sSubCache: %x\tIndex: %x\n", buf, - (reg & 0x30000) >> 16, reg & 0xfff); + int node = cpu_to_node(first_cpu(this_leaf->shared_cpu_map)); + struct pci_dev *dev = k8_northbridges[node]; + ssize_t ret = 0; + int i; - } - return ret; + if (!this_leaf->can_disable) + return sprintf(buf, "Feature not enabled\n"); + + for (i = 0; i < 2; i++) { + unsigned int reg; + + pci_read_config_dword(dev, 0x1BC + i * 4, ®); + + ret += sprintf(buf, "%sEntry: %d\n", buf, i); + ret += sprintf(buf, "%sReads: %s\tNew Entries: %s\n", + buf, + reg & 0x80000000 ? "Disabled" : "Allowed", + reg & 0x40000000 ? "Disabled" : "Allowed"); + ret += sprintf(buf, "%sSubCache: %x\tIndex: %x\n", + buf, (reg & 0x30000) >> 16, reg & 0xfff); } - return sprintf(buf, "Feature not enabled\n"); + return ret; } -static ssize_t store_cache_disable(struct _cpuid4_info *this_leaf, const char *buf, size_t count) +static ssize_t +store_cache_disable(struct _cpuid4_info *this_leaf, const char *buf, + size_t count) { - struct pci_dev *dev; - if (this_leaf->can_disable) { - /* write the MSR value */ - unsigned int ret; - unsigned int index, val; - int node = cpu_to_node(first_cpu(this_leaf->shared_cpu_map)); - dev = k8_northbridges[node]; - - if (strlen(buf) > 15) - return -EINVAL; - ret = sscanf(buf, "%x %x", &index, &val); - if (ret != 2) - return -EINVAL; - if (index > 1) - return -EINVAL; - val |= 0xc0000000; - pci_write_config_dword(dev, 0x1BC + index * 4, val & ~0x40000000); - wbinvd(); - pci_write_config_dword(dev, 0x1BC + index * 4, val); - return 1; - } - return 0; + int node = cpu_to_node(first_cpu(this_leaf->shared_cpu_map)); + struct pci_dev *dev = k8_northbridges[node]; + unsigned int ret, index, val; + + if (!this_leaf->can_disable) + return 0; + + /* write the MSR value */ + + if (strlen(buf) > 15) + return -EINVAL; + + ret = sscanf(buf, "%x %x", &index, &val); + if (ret != 2) + return -EINVAL; + if (index > 1) + return -EINVAL; + + val |= 0xc0000000; + pci_write_config_dword(dev, 0x1BC + index * 4, val & ~0x40000000); + wbinvd(); + pci_write_config_dword(dev, 0x1BC + index * 4, val); + + return 1; } struct _cache_attr { -- GitLab From a24e8d36f5fc047dac9af6200322ed393f2e3175 Mon Sep 17 00:00:00 2001 From: Mark Langsdorf Date: Tue, 22 Jul 2008 13:06:02 -0500 Subject: [PATCH 025/750] x86: L3 cache index disable for 2.6.26 On Monday 21 July 2008, Ingo Molnar wrote: > > applied to tip/x86/cpu, thanks Mark. > > > > I've done some coding style fixes for the new functions you've > > introduced, see that commit below. > > -tip testing found the following build failure: > > arch/x86/kernel/built-in.o: In function `show_cache_disable': > intel_cacheinfo.c:(.text+0xbbf2): undefined reference to `k8_northbridges' > arch/x86/kernel/built-in.o: In function `store_cache_disable': > intel_cacheinfo.c:(.text+0xbd91): undefined reference to `k8_northbridges' > > please send a delta fix patch against the tip/x86/cpu branch: > > http://people.redhat.com/mingo/tip.git/README > > which has your patch plus the cleanup applied. delta fix patch follows. It removes the dependency on k8_northbridges. -Mark Langsdorf Operating System Research Center AMD Signed-off-by: Mark Langsdorf Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/intel_cacheinfo.c | 43 +++++++++++++++++++++++---- 1 file changed, 38 insertions(+), 5 deletions(-) diff --git a/arch/x86/kernel/cpu/intel_cacheinfo.c b/arch/x86/kernel/cpu/intel_cacheinfo.c index a61c9e399ba..a0c6c6ffed4 100644 --- a/arch/x86/kernel/cpu/intel_cacheinfo.c +++ b/arch/x86/kernel/cpu/intel_cacheinfo.c @@ -13,10 +13,10 @@ #include #include #include +#include #include #include -#include #define LVL_1_INST 1 #define LVL_1_DATA 2 @@ -135,6 +135,12 @@ struct _cpuid4_info { cpumask_t shared_cpu_map; /* future?: only cpus/node is needed */ }; +static struct pci_device_id k8_nb_id[] = { + { PCI_DEVICE(PCI_VENDOR_ID_AMD, 0x1103) }, + { PCI_DEVICE(PCI_VENDOR_ID_AMD, 0x1203) }, + {} +}; + unsigned short num_cache_leaves; /* AMD doesn't have CPUID4. Emulate it here to report the same @@ -655,16 +661,39 @@ static ssize_t show_type(struct _cpuid4_info *this_leaf, char *buf) { #define to_object(k) container_of(k, struct _index_kobject, kobj) #define to_attr(a) container_of(a, struct _cache_attr, attr) +static struct pci_dev *get_k8_northbridge(int node) +{ + struct pci_dev *dev = NULL; + int i; + + for (i = 0; i <= node; i++) { + do { + dev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, dev); + if (!dev) + break; + } while (!pci_match_id(&k8_nb_id[0], dev)); + if (!dev) + break; + } + return dev; +} + static ssize_t show_cache_disable(struct _cpuid4_info *this_leaf, char *buf) { int node = cpu_to_node(first_cpu(this_leaf->shared_cpu_map)); - struct pci_dev *dev = k8_northbridges[node]; + struct pci_dev *dev = NULL; ssize_t ret = 0; int i; if (!this_leaf->can_disable) return sprintf(buf, "Feature not enabled\n"); + dev = get_k8_northbridge(node); + if (!dev) { + printk(KERN_ERR "Attempting AMD northbridge operation on a system with no northbridge\n"); + return -EINVAL; + } + for (i = 0; i < 2; i++) { unsigned int reg; @@ -686,14 +715,12 @@ store_cache_disable(struct _cpuid4_info *this_leaf, const char *buf, size_t count) { int node = cpu_to_node(first_cpu(this_leaf->shared_cpu_map)); - struct pci_dev *dev = k8_northbridges[node]; + struct pci_dev *dev = NULL; unsigned int ret, index, val; if (!this_leaf->can_disable) return 0; - /* write the MSR value */ - if (strlen(buf) > 15) return -EINVAL; @@ -704,6 +731,12 @@ store_cache_disable(struct _cpuid4_info *this_leaf, const char *buf, return -EINVAL; val |= 0xc0000000; + dev = get_k8_northbridge(node); + if (!dev) { + printk(KERN_ERR "Attempting AMD northbridge operation on a system with no northbridge\n"); + return -EINVAL; + } + pci_write_config_dword(dev, 0x1BC + index * 4, val & ~0x40000000); wbinvd(); pci_write_config_dword(dev, 0x1BC + index * 4, val); -- GitLab From cdcf772ed163651cacac8098b4974aba7f9e1c73 Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Mon, 28 Jul 2008 16:20:08 +0200 Subject: [PATCH 026/750] x86 l3 cache index disable for 2 6 26 fix Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/intel_cacheinfo.c | 39 ++++++++++++++------------- 1 file changed, 20 insertions(+), 19 deletions(-) diff --git a/arch/x86/kernel/cpu/intel_cacheinfo.c b/arch/x86/kernel/cpu/intel_cacheinfo.c index a0c6c6ffed4..535d662716d 100644 --- a/arch/x86/kernel/cpu/intel_cacheinfo.c +++ b/arch/x86/kernel/cpu/intel_cacheinfo.c @@ -1,8 +1,8 @@ /* - * Routines to indentify caches on Intel CPU. + * Routines to indentify caches on Intel CPU. * - * Changes: - * Venkatesh Pallipadi : Adding cache identification through cpuid(4) + * Changes: + * Venkatesh Pallipadi : Adding cache identification through cpuid(4) * Ashok Raj : Work with CPU hotplug infrastructure. * Andi Kleen / Andreas Herrmann : CPUID4 emulation on AMD. */ @@ -136,9 +136,9 @@ struct _cpuid4_info { }; static struct pci_device_id k8_nb_id[] = { - { PCI_DEVICE(PCI_VENDOR_ID_AMD, 0x1103) }, - { PCI_DEVICE(PCI_VENDOR_ID_AMD, 0x1203) }, - {} + { PCI_DEVICE(PCI_VENDOR_ID_AMD, 0x1103) }, + { PCI_DEVICE(PCI_VENDOR_ID_AMD, 0x1203) }, + {} }; unsigned short num_cache_leaves; @@ -190,9 +190,10 @@ static unsigned short assocs[] __cpuinitdata = { static unsigned char levels[] __cpuinitdata = { 1, 1, 2, 3 }; static unsigned char types[] __cpuinitdata = { 1, 2, 3, 3 }; -static void __cpuinit amd_cpuid4(int leaf, union _cpuid4_leaf_eax *eax, - union _cpuid4_leaf_ebx *ebx, - union _cpuid4_leaf_ecx *ecx) +static void __cpuinit +amd_cpuid4(int leaf, union _cpuid4_leaf_eax *eax, + union _cpuid4_leaf_ebx *ebx, + union _cpuid4_leaf_ecx *ecx) { unsigned dummy; unsigned line_size, lines_per_tag, assoc, size_in_kb; @@ -264,7 +265,7 @@ amd_check_l3_disable(int index, struct _cpuid4_info *this_leaf) { if (index < 3) return; - this_leaf->can_disable = 1; + this_leaf->can_disable = 1; } static int @@ -474,7 +475,7 @@ unsigned int __cpuinit init_intel_cacheinfo(struct cpuinfo_x86 *c) /* pointer to _cpuid4_info array (for each cache leaf) */ static DEFINE_PER_CPU(struct _cpuid4_info *, cpuid4_info); -#define CPUID4_INFO_IDX(x, y) (&((per_cpu(cpuid4_info, x))[y])) +#define CPUID4_INFO_IDX(x, y) (&((per_cpu(cpuid4_info, x))[y])) #ifdef CONFIG_SMP static void __cpuinit cache_shared_cpu_map_setup(unsigned int cpu, int index) @@ -511,7 +512,7 @@ static void __cpuinit cache_remove_shared_cpu_map(unsigned int cpu, int index) this_leaf = CPUID4_INFO_IDX(cpu, index); for_each_cpu_mask(sibling, this_leaf->shared_cpu_map) { - sibling_leaf = CPUID4_INFO_IDX(sibling, index); + sibling_leaf = CPUID4_INFO_IDX(sibling, index); cpu_clear(cpu, sibling_leaf->shared_cpu_map); } } @@ -593,7 +594,7 @@ struct _index_kobject { /* pointer to array of kobjects for cpuX/cache/indexY */ static DEFINE_PER_CPU(struct _index_kobject *, index_kobject); -#define INDEX_KOBJECT_PTR(x, y) (&((per_cpu(index_kobject, x))[y])) +#define INDEX_KOBJECT_PTR(x, y) (&((per_cpu(index_kobject, x))[y])) #define show_one_plus(file_name, object, val) \ static ssize_t show_##file_name \ @@ -675,7 +676,7 @@ static struct pci_dev *get_k8_northbridge(int node) if (!dev) break; } - return dev; + return dev; } static ssize_t show_cache_disable(struct _cpuid4_info *this_leaf, char *buf) @@ -736,7 +737,7 @@ store_cache_disable(struct _cpuid4_info *this_leaf, const char *buf, printk(KERN_ERR "Attempting AMD northbridge operation on a system with no northbridge\n"); return -EINVAL; } - + pci_write_config_dword(dev, 0x1BC + index * 4, val & ~0x40000000); wbinvd(); pci_write_config_dword(dev, 0x1BC + index * 4, val); @@ -789,7 +790,7 @@ static ssize_t show(struct kobject * kobj, struct attribute * attr, char * buf) ret = fattr->show ? fattr->show(CPUID4_INFO_IDX(this_leaf->cpu, this_leaf->index), buf) : - 0; + 0; return ret; } @@ -800,9 +801,9 @@ static ssize_t store(struct kobject * kobj, struct attribute * attr, struct _index_kobject *this_leaf = to_object(kobj); ssize_t ret; - ret = fattr->store ? - fattr->store(CPUID4_INFO_IDX(this_leaf->cpu, this_leaf->index), - buf, count) : + ret = fattr->store ? + fattr->store(CPUID4_INFO_IDX(this_leaf->cpu, this_leaf->index), + buf, count) : 0; return ret; } -- GitLab From 239bd83104ec6bcba90221d8b0973d2565142ef8 Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Mon, 28 Jul 2008 16:45:49 +0200 Subject: [PATCH 027/750] x86: L3 cache index disable for 2.6.26, fix #2 fix !PCI build failure: arch/x86/kernel/cpu/intel_cacheinfo.c: In function 'get_k8_northbridge': arch/x86/kernel/cpu/intel_cacheinfo.c:675: error: implicit declaration of function 'pci_match_id' Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/intel_cacheinfo.c | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/arch/x86/kernel/cpu/intel_cacheinfo.c b/arch/x86/kernel/cpu/intel_cacheinfo.c index d763d24187c..1677b55371a 100644 --- a/arch/x86/kernel/cpu/intel_cacheinfo.c +++ b/arch/x86/kernel/cpu/intel_cacheinfo.c @@ -135,11 +135,13 @@ struct _cpuid4_info { cpumask_t shared_cpu_map; /* future?: only cpus/node is needed */ }; +#ifdef CONFIG_PCI static struct pci_device_id k8_nb_id[] = { { PCI_DEVICE(PCI_VENDOR_ID_AMD, 0x1103) }, { PCI_DEVICE(PCI_VENDOR_ID_AMD, 0x1203) }, {} }; +#endif unsigned short num_cache_leaves; @@ -663,6 +665,7 @@ static ssize_t show_type(struct _cpuid4_info *this_leaf, char *buf) { #define to_object(k) container_of(k, struct _index_kobject, kobj) #define to_attr(a) container_of(a, struct _cache_attr, attr) +#ifdef CONFIG_PCI static struct pci_dev *get_k8_northbridge(int node) { struct pci_dev *dev = NULL; @@ -679,6 +682,12 @@ static struct pci_dev *get_k8_northbridge(int node) } return dev; } +#else +static struct pci_dev *get_k8_northbridge(int node) +{ + return NULL; +} +#endif static ssize_t show_cache_disable(struct _cpuid4_info *this_leaf, char *buf) { -- GitLab From 558a171d778293176bf70bc34e18a92faef5bfa1 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Tue, 29 Jul 2008 01:14:59 -0400 Subject: [PATCH 028/750] Input: wm97xx - enable sub-drivers by default Currently the support for each WM97xx touchscreen model is compiled out by default, meaning that the default configuration when the driver is built is for it to support no hardware. This is suboptimal and leads to problems like distribution kernels shipping a non-functional driver. Change the default to support all controllers and update the help text to reflect this. Signed-off-by: Mark Brown Signed-off-by: Dmitry Torokhov --- drivers/input/touchscreen/Kconfig | 21 +++++++++------------ 1 file changed, 9 insertions(+), 12 deletions(-) diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig index 6e60a97a234..25287e80e23 100644 --- a/drivers/input/touchscreen/Kconfig +++ b/drivers/input/touchscreen/Kconfig @@ -249,29 +249,26 @@ config TOUCHSCREEN_WM97XX config TOUCHSCREEN_WM9705 bool "WM9705 Touchscreen interface support" depends on TOUCHSCREEN_WM97XX + default y help - Say Y here if you have a Wolfson Microelectronics WM9705 - touchscreen controller connected to your system. - - If unsure, say N. + Say Y here to enable support for the Wolfson Microelectronics + WM9705 touchscreen controller. config TOUCHSCREEN_WM9712 bool "WM9712 Touchscreen interface support" depends on TOUCHSCREEN_WM97XX + default y help - Say Y here if you have a Wolfson Microelectronics WM9712 - touchscreen controller connected to your system. - - If unsure, say N. + Say Y here to enable support for the Wolfson Microelectronics + WM9712 touchscreen controller. config TOUCHSCREEN_WM9713 bool "WM9713 Touchscreen interface support" depends on TOUCHSCREEN_WM97XX + default y help - Say Y here if you have a Wolfson Microelectronics WM9713 touchscreen - controller connected to your system. - - If unsure, say N. + Say Y here to enable support for the Wolfson Microelectronics + WM9713 touchscreen controller. config TOUCHSCREEN_WM97XX_MAINSTONE tristate "WM97xx Mainstone accelerated touch" -- GitLab From 74dd4393445ba37b79041d92de6ff7e7b68a4aec Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= Date: Wed, 30 Jul 2008 10:33:43 -0400 Subject: [PATCH 029/750] Input: gpio-keys - fix possible NULL pointer dereference MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit bdata->button is used in gpio_check_button but never initialized. Having a device with debounce_interval != 0 without this patch resulted on an oops on my machine. Signed-off-by: Uwe Kleine-König Signed-off-by: Dmitry Torokhov --- drivers/input/keyboard/gpio_keys.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/input/keyboard/gpio_keys.c b/drivers/input/keyboard/gpio_keys.c index be58730e636..1a92f4b04c1 100644 --- a/drivers/input/keyboard/gpio_keys.c +++ b/drivers/input/keyboard/gpio_keys.c @@ -118,6 +118,7 @@ static int __devinit gpio_keys_probe(struct platform_device *pdev) unsigned int type = button->type ?: EV_KEY; bdata->input = input; + bdata->button = button; setup_timer(&bdata->timer, gpio_check_button, (unsigned long)bdata); -- GitLab From 9b07044cd8bd15fb5991e9b27136979a43538636 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= Date: Wed, 30 Jul 2008 10:34:02 -0400 Subject: [PATCH 030/750] Input: gpio-keys - make gpio_keys_device_driver static MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This fixes the sparse warning symbol 'gpio_keys_device_driver' was not declared. Should it be static? Signed-off-by: Uwe Kleine-König Signed-off-by: Dmitry Torokhov --- drivers/input/keyboard/gpio_keys.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/input/keyboard/gpio_keys.c b/drivers/input/keyboard/gpio_keys.c index 1a92f4b04c1..3f48279f219 100644 --- a/drivers/input/keyboard/gpio_keys.c +++ b/drivers/input/keyboard/gpio_keys.c @@ -257,7 +257,7 @@ static int gpio_keys_resume(struct platform_device *pdev) #define gpio_keys_resume NULL #endif -struct platform_driver gpio_keys_device_driver = { +static struct platform_driver gpio_keys_device_driver = { .probe = gpio_keys_probe, .remove = __devexit_p(gpio_keys_remove), .suspend = gpio_keys_suspend, -- GitLab From d488d3ed009ab16eeda230cd1d42e394e868f32a Mon Sep 17 00:00:00 2001 From: Harley Laue Date: Wed, 30 Jul 2008 10:46:39 -0400 Subject: [PATCH 031/750] Input: xpad - add Pelican Eclipse D-Pad to the list of devices Signed-off-by: Harley Laue Signed-off-by: Dmitry Torokhov --- drivers/input/joystick/xpad.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/input/joystick/xpad.c b/drivers/input/joystick/xpad.c index 87d3e7eabff..6791be81eb2 100644 --- a/drivers/input/joystick/xpad.c +++ b/drivers/input/joystick/xpad.c @@ -127,6 +127,7 @@ static const struct xpad_device { { 0x0738, 0x4716, "Mad Catz Wired Xbox 360 Controller", MAP_DPAD_TO_AXES, XTYPE_XBOX360 }, { 0x0738, 0x6040, "Mad Catz Beat Pad Pro", MAP_DPAD_TO_BUTTONS, XTYPE_XBOX }, { 0x0c12, 0x8802, "Zeroplus Xbox Controller", MAP_DPAD_TO_AXES, XTYPE_XBOX }, + { 0x0c12, 0x880a, "Pelican Eclipse PL-2023", MAP_DPAD_TO_AXES, XTYPE_XBOX }, { 0x0c12, 0x8810, "Zeroplus Xbox Controller", MAP_DPAD_TO_AXES, XTYPE_XBOX }, { 0x0c12, 0x9902, "HAMA VibraX - *FAULTY HARDWARE*", MAP_DPAD_TO_AXES, XTYPE_XBOX }, { 0x0e4c, 0x1097, "Radica Gamester Controller", MAP_DPAD_TO_AXES, XTYPE_XBOX }, -- GitLab From 19052c0e85a3e9d3b7d190b29fcdbf0e6c105381 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Tue, 5 Aug 2008 15:54:13 +1000 Subject: [PATCH 032/750] Make writes to md/safe_mode_delay immediately effective. If we reduce the 'safe_mode_delay', it could still wait for the old delay to completely expire before doing anything about safe_mode. Thus the effect if the change is delayed. To make the effect more immediate, run the timeout function immediately if the delay was reduced. This may cause it to run slightly earlier that required, but that is the safer option. Signed-off-by: NeilBrown --- drivers/md/md.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/md/md.c b/drivers/md/md.c index c7aae66c6f9..48afe4f7ad4 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -2393,6 +2393,8 @@ static void analyze_sbs(mddev_t * mddev) } +static void md_safemode_timeout(unsigned long data); + static ssize_t safe_delay_show(mddev_t *mddev, char *page) { @@ -2432,9 +2434,12 @@ safe_delay_store(mddev_t *mddev, const char *cbuf, size_t len) if (msec == 0) mddev->safemode_delay = 0; else { + unsigned long old_delay = mddev->safemode_delay; mddev->safemode_delay = (msec*HZ)/1000; if (mddev->safemode_delay == 0) mddev->safemode_delay = 1; + if (mddev->safemode_delay < old_delay) + md_safemode_timeout((unsigned long)mddev); } return len; } -- GitLab From 2b25000bf5157c28d8591f03f0575248a8cbd900 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Tue, 5 Aug 2008 15:54:13 +1000 Subject: [PATCH 033/750] Restore force switch of md array to readonly at reboot time. A recent patch allowed do_md_stop to know whether it was being called via an ioctl or not, and thus where to allow for an extra open file descriptor when checking if it is in use. This broke then switch to readonly performed by the shutdown notifier, which needs to work even when the array is still (apparently) active (as md doesn't get told when the filesystem becomes readonly). So restore this feature by pretending that there can be lots of file descriptors open, but we still want do_md_stop to switch to readonly. Signed-off-by: NeilBrown --- drivers/md/md.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/drivers/md/md.c b/drivers/md/md.c index 48afe4f7ad4..8d11cd1a0d8 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -6237,7 +6237,11 @@ static int md_notify_reboot(struct notifier_block *this, for_each_mddev(mddev, tmp) if (mddev_trylock(mddev)) { - do_md_stop (mddev, 1, 0); + /* Force a switch to readonly even array + * appears to still be in use. Hence + * the '100'. + */ + do_md_stop (mddev, 1, 100); mddev_unlock(mddev); } /* -- GitLab From dba034eef2456d2a9f9a76806846c97acf6c3ad1 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Tue, 5 Aug 2008 15:54:13 +1000 Subject: [PATCH 034/750] Fail safely when trying to grow an array with a write-intent bitmap. We cannot currently change the size of a write-intent bitmap. So if we change the size of an array which has such a bitmap, it tries to set bits beyond the end of the bitmap. For now, simply reject any request to change the size of an array which has a bitmap. mdadm can remove the bitmap and add a new one after the array has changed size. Signed-off-by: NeilBrown --- drivers/md/md.c | 5 +++++ drivers/md/raid5.c | 3 +++ 2 files changed, 8 insertions(+) diff --git a/drivers/md/md.c b/drivers/md/md.c index 8d11cd1a0d8..6eb95451f16 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -4639,6 +4639,11 @@ static int update_size(mddev_t *mddev, sector_t num_sectors) */ if (mddev->sync_thread) return -EBUSY; + if (mddev->bitmap) + /* Sorry, cannot grow a bitmap yet, just remove it, + * grow, and re-add. + */ + return -EBUSY; rdev_for_each(rdev, tmp, mddev) { sector_t avail; avail = rdev->size * 2; diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c index 40e93967565..17e0953c3c0 100644 --- a/drivers/md/raid5.c +++ b/drivers/md/raid5.c @@ -4446,6 +4446,9 @@ static int raid5_check_reshape(mddev_t *mddev) return -EINVAL; /* Cannot shrink array or change level yet */ if (mddev->delta_disks == 0) return 0; /* nothing to do */ + if (mddev->bitmap) + /* Cannot grow a bitmap yet */ + return -EBUSY; /* Can only proceed if there are plenty of stripe_heads. * We need a minimum of one full stripe,, and for sensible progress -- GitLab From ac4090d24c6a26211bc4523d920376e054d4f3f8 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Tue, 5 Aug 2008 15:54:13 +1000 Subject: [PATCH 035/750] Don't let a blocked_rdev interfere with read request in raid5/6 When we have externally managed metadata, we need to mark a failed device as 'Blocked' and not allow any writes until that device have been marked as faulty in the metadata and the Blocked flag has been removed. However it is perfectly OK to allow read requests when there is a Blocked device, and with a readonly array, there may not be any metadata-handler watching for blocked devices. So in raid5/raid6 only allow a Blocked device to interfere with Write request or resync. Read requests go through untouched. raid1 and raid10 already differentiate between read and write properly. Signed-off-by: NeilBrown --- drivers/md/raid5.c | 29 +++++++++++++++++++++-------- 1 file changed, 21 insertions(+), 8 deletions(-) diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c index 17e0953c3c0..224de022e7c 100644 --- a/drivers/md/raid5.c +++ b/drivers/md/raid5.c @@ -2568,10 +2568,10 @@ static bool handle_stripe5(struct stripe_head *sh) if (dev->written) s.written++; rdev = rcu_dereference(conf->disks[i].rdev); - if (rdev && unlikely(test_bit(Blocked, &rdev->flags))) { + if (blocked_rdev == NULL && + rdev && unlikely(test_bit(Blocked, &rdev->flags))) { blocked_rdev = rdev; atomic_inc(&rdev->nr_pending); - break; } if (!rdev || !test_bit(In_sync, &rdev->flags)) { /* The ReadError flag will just be confusing now */ @@ -2588,8 +2588,14 @@ static bool handle_stripe5(struct stripe_head *sh) rcu_read_unlock(); if (unlikely(blocked_rdev)) { - set_bit(STRIPE_HANDLE, &sh->state); - goto unlock; + if (s.syncing || s.expanding || s.expanded || + s.to_write || s.written) { + set_bit(STRIPE_HANDLE, &sh->state); + goto unlock; + } + /* There is nothing for the blocked_rdev to block */ + rdev_dec_pending(blocked_rdev, conf->mddev); + blocked_rdev = NULL; } if (s.to_fill && !test_bit(STRIPE_BIOFILL_RUN, &sh->state)) { @@ -2832,10 +2838,10 @@ static bool handle_stripe6(struct stripe_head *sh, struct page *tmp_page) if (dev->written) s.written++; rdev = rcu_dereference(conf->disks[i].rdev); - if (rdev && unlikely(test_bit(Blocked, &rdev->flags))) { + if (blocked_rdev == NULL && + rdev && unlikely(test_bit(Blocked, &rdev->flags))) { blocked_rdev = rdev; atomic_inc(&rdev->nr_pending); - break; } if (!rdev || !test_bit(In_sync, &rdev->flags)) { /* The ReadError flag will just be confusing now */ @@ -2853,9 +2859,16 @@ static bool handle_stripe6(struct stripe_head *sh, struct page *tmp_page) rcu_read_unlock(); if (unlikely(blocked_rdev)) { - set_bit(STRIPE_HANDLE, &sh->state); - goto unlock; + if (s.syncing || s.expanding || s.expanded || + s.to_write || s.written) { + set_bit(STRIPE_HANDLE, &sh->state); + goto unlock; + } + /* There is nothing for the blocked_rdev to block */ + rdev_dec_pending(blocked_rdev, conf->mddev); + blocked_rdev = NULL; } + pr_debug("locked=%d uptodate=%d to_read=%d" " to_write=%d failed=%d failed_num=%d,%d\n", s.locked, s.uptodate, s.to_read, s.to_write, s.failed, -- GitLab From c89a8eee61540df04fc83f32f51ef0f46ec018b1 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Tue, 5 Aug 2008 15:54:13 +1000 Subject: [PATCH 036/750] Allow faulty devices to be removed from a readonly array. Removing faulty devices from an array is a two stage process. First the device is moved from being a part of the active array to being similar to a spare device. Then it can be removed by a request from user space. The first step is currently not performed for read-only arrays, so the second step can never succeed. So allow readonly arrays to remove failed devices (which aren't blocked). Signed-off-by: NeilBrown --- drivers/md/md.c | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-) diff --git a/drivers/md/md.c b/drivers/md/md.c index 6eb95451f16..25b893ec562 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -6003,7 +6003,7 @@ static int remove_and_add_spares(mddev_t *mddev) } } - if (mddev->degraded) { + if (mddev->degraded && ! mddev->ro) { rdev_for_each(rdev, rtmp, mddev) { if (rdev->raid_disk >= 0 && !test_bit(In_sync, &rdev->flags) && @@ -6077,6 +6077,8 @@ void md_check_recovery(mddev_t *mddev) flush_signals(current); } + if (mddev->ro && !test_bit(MD_RECOVERY_NEEDED, &mddev->recovery)) + return; if ( ! ( (mddev->flags && !mddev->external) || test_bit(MD_RECOVERY_NEEDED, &mddev->recovery) || @@ -6090,6 +6092,15 @@ void md_check_recovery(mddev_t *mddev) if (mddev_trylock(mddev)) { int spares = 0; + if (mddev->ro) { + /* Only thing we do on a ro array is remove + * failed devices. + */ + remove_and_add_spares(mddev); + clear_bit(MD_RECOVERY_NEEDED, &mddev->recovery); + goto unlock; + } + if (!mddev->external) { int did_change = 0; spin_lock_irq(&mddev->write_lock); -- GitLab From 0310fa216decc3ecfab41f327638fa48a81f3735 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Tue, 5 Aug 2008 15:54:14 +1000 Subject: [PATCH 037/750] Allow raid10 resync to happening in larger chunks. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The raid10 resync/recovery code currently limits the amount of in-flight resync IO to 2Meg. This was copied from raid1 where it seems quite adequate. However for raid10, some layouts require a bit of seeking to perform a resync, and allowing a larger buffer size means that the seeking can be significantly reduced. There is probably no real need to limit the amount of in-flight IO at all. Any shortage of memory will naturally reduce the amount of buffer space available down to a set minimum, and any concurrent normal IO will quickly cause resync IO to back off. The only problem would be that normal IO has to wait for all resync IO to finish, so a very large amount of resync IO could cause unpleasant latency when normal IO starts up. So: increase RESYNC_DEPTH to allow 32Meg of buffer (if memory is available) which seems to be a good amount. Also reduce the amount of memory reserved as there is no need to keep 2Meg just for resync if memory is tight. Thanks to Keld for the suggestion. Cc: Keld Jørn Simonsen Signed-off-by: NeilBrown --- drivers/md/raid10.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) diff --git a/drivers/md/raid10.c b/drivers/md/raid10.c index d41bebb6da0..e34cd0e6247 100644 --- a/drivers/md/raid10.c +++ b/drivers/md/raid10.c @@ -76,11 +76,13 @@ static void r10bio_pool_free(void *r10_bio, void *data) kfree(r10_bio); } +/* Maximum size of each resync request */ #define RESYNC_BLOCK_SIZE (64*1024) -//#define RESYNC_BLOCK_SIZE PAGE_SIZE -#define RESYNC_SECTORS (RESYNC_BLOCK_SIZE >> 9) #define RESYNC_PAGES ((RESYNC_BLOCK_SIZE + PAGE_SIZE-1) / PAGE_SIZE) -#define RESYNC_WINDOW (2048*1024) +/* amount of memory to reserve for resync requests */ +#define RESYNC_WINDOW (1024*1024) +/* maximum number of concurrent requests, memory permitting */ +#define RESYNC_DEPTH (32*1024*1024/RESYNC_BLOCK_SIZE) /* * When performing a resync, we need to read and compare, so @@ -690,7 +692,6 @@ static int flush_pending_writes(conf_t *conf) * there is no normal IO happeing. It must arrange to call * lower_barrier when the particular background IO completes. */ -#define RESYNC_DEPTH 32 static void raise_barrier(conf_t *conf, int force) { -- GitLab From 0f0625d895bc5b3c3d7352486a94e5a75f10fd35 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Tue, 5 Aug 2008 17:10:58 +0800 Subject: [PATCH 038/750] Blackfin arch: remove useless mtd defines in uClinux dont bother protecting the mtd defines as anything that incorrectly uses it will get an error during link time anyways ... this prevents large pointless rebuilds of most files whenever the uclinux mtd map changes state Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- include/asm-blackfin/bfin-global.h | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/include/asm-blackfin/bfin-global.h b/include/asm-blackfin/bfin-global.h index 320aa5e167e..9fbbee61f98 100644 --- a/include/asm-blackfin/bfin-global.h +++ b/include/asm-blackfin/bfin-global.h @@ -122,9 +122,8 @@ extern char _stext_l1[], _etext_l1[], _sdata_l1[], _edata_l1[], _sbss_l1[], _stext_l2[], _etext_l2[], _sdata_l2[], _edata_l2[], _sbss_l2[], _ebss_l2[], _l2_lma_start[]; -#ifdef CONFIG_MTD_UCLINUX +/* only used when CONFIG_MTD_UCLINUX */ extern unsigned long memory_mtd_start, memory_mtd_end, mtd_size; -#endif #endif -- GitLab From 5400c5aa2de41501be7529831c9df36c729bf371 Mon Sep 17 00:00:00 2001 From: Jie Zhang Date: Tue, 5 Aug 2008 17:33:38 +0800 Subject: [PATCH 039/750] Blackfin arch: Fix bug - This change eliminates impact on application debugging Signed-off-by: Jie Zhang Signed-off-by: Bryan Wu --- arch/blackfin/mach-common/entry.S | 20 +++++++++++++------- 1 file changed, 13 insertions(+), 7 deletions(-) diff --git a/arch/blackfin/mach-common/entry.S b/arch/blackfin/mach-common/entry.S index eceb484d90f..3db2f4df261 100644 --- a/arch/blackfin/mach-common/entry.S +++ b/arch/blackfin/mach-common/entry.S @@ -158,6 +158,7 @@ ENTRY(_ex_single_step) cc = r7 == r6; if cc jump _bfin_return_from_exception; +#ifdef CONFIG_KGDB /* Don't do single step in hardware exception handler */ p5.l = lo(IPEND); p5.h = hi(IPEND); @@ -165,7 +166,6 @@ ENTRY(_ex_single_step) cc = bittst(r6, 5); if cc jump _bfin_return_from_exception; -#ifdef CONFIG_KGDB /* skip single step if current interrupt priority is higher than * that of the first instruction, from which gdb starts single step */ r6 >>= 6; @@ -191,12 +191,22 @@ ENTRY(_ex_single_step) #endif /* If we were in user mode, do the single step normally. */ + p5.l = lo(IPEND); + p5.h = hi(IPEND); r6 = [p5]; r7 = 0xffe0 (z); r7 = r7 & r6; cc = r7 == 0; - if cc jump 1f; + if !cc jump 1f; + /* Single stepping only a single instruction, so clear the trace + * bit here. */ + r7 = syscfg; + bitclr (r7, 0); + syscfg = R7; + jump _ex_trap_c; + +1: /* * We were in an interrupt handler. By convention, all of them save * SYSCFG with their first instruction, so by checking whether our @@ -224,15 +234,11 @@ ENTRY(_ex_single_step) cc = R7 == R6; if !cc jump _bfin_return_from_exception; -1: - /* Single stepping only a single instruction, so clear the trace - * bit here. */ r7 = syscfg; bitclr (r7, 0); syscfg = R7; - jump _ex_trap_c; - + /* Fall through to _bfin_return_from_exception. */ ENDPROC(_ex_single_step) ENTRY(_bfin_return_from_exception) -- GitLab From 4a88d0ce494034fbb8dd0076d80e71b38abf5748 Mon Sep 17 00:00:00 2001 From: Michael Hennerich Date: Tue, 5 Aug 2008 17:38:41 +0800 Subject: [PATCH 040/750] Blackfin arch: Functional power management support Merge VR Regulator Hibernate wakeups into set_irq_wake for internal interrupts. Signed-off-by: Michael Hennerich Signed-off-by: Bryan Wu --- arch/blackfin/Kconfig | 36 ------------------ arch/blackfin/mach-common/ints-priority.c | 46 +++++++++++++++++++++-- arch/blackfin/mach-common/pm.c | 18 +-------- include/asm-blackfin/bfin-global.h | 1 + 4 files changed, 45 insertions(+), 56 deletions(-) diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig index 5a097c46bc4..cc2add7e39e 100644 --- a/arch/blackfin/Kconfig +++ b/arch/blackfin/Kconfig @@ -933,13 +933,6 @@ endchoice comment "Possible Suspend Mem / Hibernate Wake-Up Sources" depends on PM -config PM_BFIN_WAKE_RTC - bool "Allow Wake-Up from RESET and on-chip RTC" - depends on PM - default n - help - Enable RTC Wake-Up (Voltage Regulator Power-Up) - config PM_BFIN_WAKE_PH6 bool "Allow Wake-Up from on-chip PHY or PH6 GP" depends on PM && (BF52x || BF534 || BF536 || BF537) @@ -947,41 +940,12 @@ config PM_BFIN_WAKE_PH6 help Enable PHY and PH6 GP Wake-Up (Voltage Regulator Power-Up) -config PM_BFIN_WAKE_CAN - bool "Allow Wake-Up from on-chip CAN0/1" - depends on PM && (BF54x || BF534 || BF536 || BF537) - default n - help - Enable CAN0/1 Wake-Up (Voltage Regulator Power-Up) - config PM_BFIN_WAKE_GP bool "Allow Wake-Up from GPIOs" depends on PM && BF54x default n help Enable General-Purpose Wake-Up (Voltage Regulator Power-Up) - -config PM_BFIN_WAKE_USB - bool "Allow Wake-Up from on-chip USB" - depends on PM && (BF54x || BF52x) - default n - help - Enable USB Wake-Up (Voltage Regulator Power-Up) - -config PM_BFIN_WAKE_KEYPAD - bool "Allow Wake-Up from on-chip Keypad" - depends on PM && BF54x - default n - help - Enable Keypad Wake-Up (Voltage Regulator Power-Up) - -config PM_BFIN_WAKE_ROTARY - bool "Allow Wake-Up from on-chip Rotary" - depends on PM && BF54x - default n - help - Enable Rotary Wake-Up (Voltage Regulator Power-Up) - endmenu menu "CPU Frequency scaling" diff --git a/arch/blackfin/mach-common/ints-priority.c b/arch/blackfin/mach-common/ints-priority.c index 64d746114e4..e713b9db867 100644 --- a/arch/blackfin/mach-common/ints-priority.c +++ b/arch/blackfin/mach-common/ints-priority.c @@ -71,6 +71,7 @@ atomic_t num_spurious; #ifdef CONFIG_PM unsigned long bfin_sic_iwr[3]; /* Up to 3 SIC_IWRx registers */ +unsigned vr_wakeup; #endif struct ivgx { @@ -184,17 +185,56 @@ static void bfin_internal_unmask_irq(unsigned int irq) #ifdef CONFIG_PM int bfin_internal_set_wake(unsigned int irq, unsigned int state) { - unsigned bank, bit; + unsigned bank, bit, wakeup = 0; unsigned long flags; bank = SIC_SYSIRQ(irq) / 32; bit = SIC_SYSIRQ(irq) % 32; + switch (irq) { +#ifdef IRQ_RTC + case IRQ_RTC: + wakeup |= WAKE; + break; +#endif +#ifdef IRQ_CAN0_RX + case IRQ_CAN0_RX: + wakeup |= CANWE; + break; +#endif +#ifdef IRQ_CAN1_RX + case IRQ_CAN1_RX: + wakeup |= CANWE; + break; +#endif +#ifdef IRQ_USB_INT0 + case IRQ_USB_INT0: + wakeup |= USBWE; + break; +#endif +#ifdef IRQ_KEY + case IRQ_KEY: + wakeup |= KPADWE; + break; +#endif +#ifdef IRQ_CNT + case IRQ_CNT: + wakeup |= ROTWE; + break; +#endif + default: + break; + } + local_irq_save(flags); - if (state) + if (state) { bfin_sic_iwr[bank] |= (1 << bit); - else + vr_wakeup |= wakeup; + + } else { bfin_sic_iwr[bank] &= ~(1 << bit); + vr_wakeup &= ~wakeup; + } local_irq_restore(flags); diff --git a/arch/blackfin/mach-common/pm.c b/arch/blackfin/mach-common/pm.c index 4fe6a2366b1..143134b852e 100644 --- a/arch/blackfin/mach-common/pm.c +++ b/arch/blackfin/mach-common/pm.c @@ -229,28 +229,12 @@ int bfin_pm_suspend_mem_enter(void) wakeup = bfin_read_VR_CTL() & ~FREQ; wakeup |= SCKELOW; - /* FIXME: merge this somehow with set_irq_wake */ -#ifdef CONFIG_PM_BFIN_WAKE_RTC - wakeup |= WAKE; -#endif #ifdef CONFIG_PM_BFIN_WAKE_PH6 wakeup |= PHYWE; #endif -#ifdef CONFIG_PM_BFIN_WAKE_CAN - wakeup |= CANWE; -#endif #ifdef CONFIG_PM_BFIN_WAKE_GP wakeup |= GPWE; #endif -#ifdef CONFIG_PM_BFIN_WAKE_USB - wakeup |= USBWE; -#endif -#ifdef CONFIG_PM_BFIN_WAKE_KEYPAD - wakeup |= KPADWE; -#endif -#ifdef CONFIG_PM_BFIN_WAKE_ROTARY - wakeup |= ROTWE; -#endif local_irq_save(flags); @@ -268,7 +252,7 @@ int bfin_pm_suspend_mem_enter(void) icache_disable(); bf53x_suspend_l1_mem(memptr); - do_hibernate(wakeup); /* Goodbye */ + do_hibernate(wakeup | vr_wakeup); /* Goodbye */ bf53x_resume_l1_mem(memptr); diff --git a/include/asm-blackfin/bfin-global.h b/include/asm-blackfin/bfin-global.h index 9fbbee61f98..93ae5335e8a 100644 --- a/include/asm-blackfin/bfin-global.h +++ b/include/asm-blackfin/bfin-global.h @@ -113,6 +113,7 @@ extern const char bfin_board_name[]; extern unsigned long wall_jiffies; extern unsigned long bfin_sic_iwr[]; +extern unsigned vr_wakeup; extern u16 _bfin_swrst; /* shadow for Software Reset Register (SWRST) */ extern struct file_operations dpmc_fops; extern unsigned long _ramstart, _ramend, _rambase; -- GitLab From aa5829776347dbd9eeb461f650c1d085cf463a83 Mon Sep 17 00:00:00 2001 From: Robin Getz Date: Tue, 5 Aug 2008 17:47:29 +0800 Subject: [PATCH 041/750] Blackfin arch: be consistant with parition names, and ensure the bus is identified Signed-off-by: Robin Getz Signed-off-by: Bryan Wu --- arch/blackfin/mach-bf527/boards/cm_bf527.c | 14 +++++++------- arch/blackfin/mach-bf527/boards/ezkit.c | 14 +++++++------- arch/blackfin/mach-bf533/boards/H8606.c | 6 +++--- arch/blackfin/mach-bf533/boards/cm_bf533.c | 6 +++--- arch/blackfin/mach-bf533/boards/ezkit.c | 6 +++--- arch/blackfin/mach-bf533/boards/stamp.c | 12 ++++++------ arch/blackfin/mach-bf537/boards/cm_bf537.c | 6 +++--- .../blackfin/mach-bf537/boards/generic_board.c | 6 +++--- arch/blackfin/mach-bf537/boards/minotaur.c | 6 +++--- arch/blackfin/mach-bf537/boards/pnav10.c | 6 +++--- arch/blackfin/mach-bf537/boards/stamp.c | 18 +++++++++--------- arch/blackfin/mach-bf548/boards/cm_bf548.c | 8 ++++---- arch/blackfin/mach-bf548/boards/ezkit.c | 14 +++++++------- arch/blackfin/mach-bf561/boards/cm_bf561.c | 6 +++--- arch/blackfin/mach-bf561/boards/ezkit.c | 6 +++--- 15 files changed, 67 insertions(+), 67 deletions(-) diff --git a/arch/blackfin/mach-bf527/boards/cm_bf527.c b/arch/blackfin/mach-bf527/boards/cm_bf527.c index 0b26ae2de5e..749f4a806b5 100644 --- a/arch/blackfin/mach-bf527/boards/cm_bf527.c +++ b/arch/blackfin/mach-bf527/boards/cm_bf527.c @@ -160,15 +160,15 @@ static struct platform_device musb_device = { #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) static struct mtd_partition ezkit_partitions[] = { { - .name = "Bootloader", + .name = "bootloader(nor)", .size = 0x40000, .offset = 0, }, { - .name = "Kernel", + .name = "linux kernel(nor)", .size = 0x1C0000, .offset = MTDPART_OFS_APPEND, }, { - .name = "RootFS", + .name = "file system(nor)", .size = MTDPART_SIZ_FULL, .offset = MTDPART_OFS_APPEND, } @@ -200,12 +200,12 @@ static struct platform_device ezkit_flash_device = { #if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE) static struct mtd_partition partition_info[] = { { - .name = "Linux Kernel", + .name = "linux kernel(nand)", .offset = 0, .size = 4 * SIZE_1M, }, { - .name = "File System", + .name = "file system(nand)", .offset = MTDPART_OFS_APPEND, .size = MTDPART_SIZ_FULL, }, @@ -438,12 +438,12 @@ static struct platform_device net2272_bfin_device = { || defined(CONFIG_MTD_M25P80_MODULE) static struct mtd_partition bfin_spi_flash_partitions[] = { { - .name = "bootloader", + .name = "bootloader(spi)", .size = 0x00040000, .offset = 0, .mask_flags = MTD_CAP_ROM }, { - .name = "linux kernel", + .name = "linux kernel(spi)", .size = MTDPART_SIZ_FULL, .offset = MTDPART_OFS_APPEND, } diff --git a/arch/blackfin/mach-bf527/boards/ezkit.c b/arch/blackfin/mach-bf527/boards/ezkit.c index 689b69c98ee..cbd47bce689 100644 --- a/arch/blackfin/mach-bf527/boards/ezkit.c +++ b/arch/blackfin/mach-bf527/boards/ezkit.c @@ -177,15 +177,15 @@ static struct platform_device bf52x_t350mcqb_device = { #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) static struct mtd_partition ezkit_partitions[] = { { - .name = "Bootloader", + .name = "bootloader(nor)", .size = 0x40000, .offset = 0, }, { - .name = "Kernel", + .name = "linux kernel(nor)", .size = 0x1C0000, .offset = MTDPART_OFS_APPEND, }, { - .name = "RootFS", + .name = "file system(nor)", .size = MTDPART_SIZ_FULL, .offset = MTDPART_OFS_APPEND, } @@ -217,12 +217,12 @@ static struct platform_device ezkit_flash_device = { #if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE) static struct mtd_partition partition_info[] = { { - .name = "Linux Kernel", + .name = "linux kernel(nand)", .offset = 0, .size = 4 * SIZE_1M, }, { - .name = "File System", + .name = "file system(nand)", .offset = MTDPART_OFS_APPEND, .size = MTDPART_SIZ_FULL, }, @@ -460,12 +460,12 @@ static struct platform_device net2272_bfin_device = { || defined(CONFIG_MTD_M25P80_MODULE) static struct mtd_partition bfin_spi_flash_partitions[] = { { - .name = "bootloader", + .name = "bootloader(spi)", .size = 0x00040000, .offset = 0, .mask_flags = MTD_CAP_ROM }, { - .name = "linux kernel", + .name = "linux kernel(spi)", .size = MTDPART_SIZ_FULL, .offset = MTDPART_OFS_APPEND, } diff --git a/arch/blackfin/mach-bf533/boards/H8606.c b/arch/blackfin/mach-bf533/boards/H8606.c index 4103a97c1a7..cecbc624e3d 100644 --- a/arch/blackfin/mach-bf533/boards/H8606.c +++ b/arch/blackfin/mach-bf533/boards/H8606.c @@ -141,16 +141,16 @@ static struct platform_device net2272_bfin_device = { #if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) static struct mtd_partition bfin_spi_flash_partitions[] = { { - .name = "bootloader", + .name = "bootloader(spi)", .size = 0x00060000, .offset = 0, .mask_flags = MTD_CAP_ROM }, { - .name = "kernel", + .name = "linux kernel(spi)", .size = 0x100000, .offset = 0x60000 }, { - .name = "file system", + .name = "file system(spi)", .size = 0x6a0000, .offset = 0x00160000, } diff --git a/arch/blackfin/mach-bf533/boards/cm_bf533.c b/arch/blackfin/mach-bf533/boards/cm_bf533.c index ed2b0b8f5dc..dfccf826fa3 100644 --- a/arch/blackfin/mach-bf533/boards/cm_bf533.c +++ b/arch/blackfin/mach-bf533/boards/cm_bf533.c @@ -53,16 +53,16 @@ const char bfin_board_name[] = "Bluetechnix CM BF533"; #if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) static struct mtd_partition bfin_spi_flash_partitions[] = { { - .name = "bootloader", + .name = "bootloader(spi)", .size = 0x00020000, .offset = 0, .mask_flags = MTD_CAP_ROM }, { - .name = "kernel", + .name = "linux kernel(spi)", .size = 0xe0000, .offset = 0x20000 }, { - .name = "file system", + .name = "file system(spi)", .size = 0x700000, .offset = 0x00100000, } diff --git a/arch/blackfin/mach-bf533/boards/ezkit.c b/arch/blackfin/mach-bf533/boards/ezkit.c index 079389cbd85..6a34f1519c0 100644 --- a/arch/blackfin/mach-bf533/boards/ezkit.c +++ b/arch/blackfin/mach-bf533/boards/ezkit.c @@ -90,16 +90,16 @@ static struct platform_device smc91x_device = { #if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) static struct mtd_partition bfin_spi_flash_partitions[] = { { - .name = "bootloader", + .name = "bootloader(spi)", .size = 0x00020000, .offset = 0, .mask_flags = MTD_CAP_ROM }, { - .name = "kernel", + .name = "linux kernel(spi)", .size = 0xe0000, .offset = MTDPART_OFS_APPEND, }, { - .name = "file system", + .name = "file system(spi)", .size = MTDPART_SIZ_FULL, .offset = MTDPART_OFS_APPEND, } diff --git a/arch/blackfin/mach-bf533/boards/stamp.c b/arch/blackfin/mach-bf533/boards/stamp.c index 13ae49515f7..d10b2dc5902 100644 --- a/arch/blackfin/mach-bf533/boards/stamp.c +++ b/arch/blackfin/mach-bf533/boards/stamp.c @@ -114,15 +114,15 @@ static struct platform_device net2272_bfin_device = { #if defined(CONFIG_MTD_BFIN_ASYNC) || defined(CONFIG_MTD_BFIN_ASYNC_MODULE) static struct mtd_partition stamp_partitions[] = { { - .name = "Bootloader", + .name = "bootloader(nor)", .size = 0x40000, .offset = 0, }, { - .name = "Kernel", + .name = "linux kernel(nor)", .size = 0xE0000, .offset = MTDPART_OFS_APPEND, }, { - .name = "RootFS", + .name = "file system(nor)", .size = MTDPART_SIZ_FULL, .offset = MTDPART_OFS_APPEND, } @@ -164,16 +164,16 @@ static struct platform_device stamp_flash_device = { #if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) static struct mtd_partition bfin_spi_flash_partitions[] = { { - .name = "bootloader", + .name = "bootloader(spi)", .size = 0x00040000, .offset = 0, .mask_flags = MTD_CAP_ROM }, { - .name = "kernel", + .name = "linux kernel(spi)", .size = 0xe0000, .offset = MTDPART_OFS_APPEND, }, { - .name = "file system", + .name = "file system(spi)", .size = MTDPART_SIZ_FULL, .offset = MTDPART_OFS_APPEND, } diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537.c b/arch/blackfin/mach-bf537/boards/cm_bf537.c index 73f2142875e..cb73ed5cc1a 100644 --- a/arch/blackfin/mach-bf537/boards/cm_bf537.c +++ b/arch/blackfin/mach-bf537/boards/cm_bf537.c @@ -56,16 +56,16 @@ const char bfin_board_name[] = "Bluetechnix CM BF537"; #if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) static struct mtd_partition bfin_spi_flash_partitions[] = { { - .name = "bootloader", + .name = "bootloader(spi)", .size = 0x00020000, .offset = 0, .mask_flags = MTD_CAP_ROM }, { - .name = "kernel", + .name = "linux kernel(spi)", .size = 0xe0000, .offset = 0x20000 }, { - .name = "file system", + .name = "file system(spi)", .size = 0x700000, .offset = 0x00100000, } diff --git a/arch/blackfin/mach-bf537/boards/generic_board.c b/arch/blackfin/mach-bf537/boards/generic_board.c index 01b63e2ec18..f5bc9258f83 100644 --- a/arch/blackfin/mach-bf537/boards/generic_board.c +++ b/arch/blackfin/mach-bf537/boards/generic_board.c @@ -307,16 +307,16 @@ static struct platform_device net2272_bfin_device = { || defined(CONFIG_MTD_M25P80_MODULE) static struct mtd_partition bfin_spi_flash_partitions[] = { { - .name = "bootloader", + .name = "bootloader(spi)", .size = 0x00020000, .offset = 0, .mask_flags = MTD_CAP_ROM }, { - .name = "kernel", + .name = "linux kernel(spi)", .size = 0xe0000, .offset = 0x20000 }, { - .name = "file system", + .name = "file system(spi)", .size = 0x700000, .offset = 0x00100000, } diff --git a/arch/blackfin/mach-bf537/boards/minotaur.c b/arch/blackfin/mach-bf537/boards/minotaur.c index 18ddf7a5200..48c4cd2d1be 100644 --- a/arch/blackfin/mach-bf537/boards/minotaur.c +++ b/arch/blackfin/mach-bf537/boards/minotaur.c @@ -100,16 +100,16 @@ static struct platform_device net2272_bfin_device = { static struct mtd_partition bfin_spi_flash_partitions[] = { { - .name = "uboot", + .name = "bootloader(spi)", .size = PSIZE_UBOOT, .offset = 0x000000, .mask_flags = MTD_CAP_ROM }, { - .name = "initramfs", + .name = "initramfs(spi)", .size = PSIZE_INITRAMFS, .offset = PSIZE_UBOOT }, { - .name = "opt", + .name = "opt(spi)", .size = FLASH_SIZE - (PSIZE_UBOOT + PSIZE_INITRAMFS), .offset = PSIZE_UBOOT + PSIZE_INITRAMFS, } diff --git a/arch/blackfin/mach-bf537/boards/pnav10.c b/arch/blackfin/mach-bf537/boards/pnav10.c index 51c3bab14a6..f9174c11cbd 100644 --- a/arch/blackfin/mach-bf537/boards/pnav10.c +++ b/arch/blackfin/mach-bf537/boards/pnav10.c @@ -231,16 +231,16 @@ static struct platform_device net2272_bfin_device = { || defined(CONFIG_MTD_M25P80_MODULE) static struct mtd_partition bfin_spi_flash_partitions[] = { { - .name = "bootloader", + .name = "bootloader(spi)", .size = 0x00020000, .offset = 0, .mask_flags = MTD_CAP_ROM }, { - .name = "kernel", + .name = "linux kernel(spi)", .size = 0xe0000, .offset = 0x20000 }, { - .name = "file system", + .name = "file system(spi)", .size = 0x700000, .offset = 0x00100000, } diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c index 6dbc76fb080..e93964fdb43 100644 --- a/arch/blackfin/mach-bf537/boards/stamp.c +++ b/arch/blackfin/mach-bf537/boards/stamp.c @@ -364,11 +364,11 @@ const char *part_probes[] = { "cmdlinepart", "RedBoot", NULL }; static struct mtd_partition bfin_plat_nand_partitions[] = { { - .name = "linux kernel", + .name = "linux kernel(nand)", .size = 0x400000, .offset = 0, }, { - .name = "file system", + .name = "file system(nand)", .size = MTDPART_SIZ_FULL, .offset = MTDPART_OFS_APPEND, }, @@ -439,19 +439,19 @@ static void bfin_plat_nand_init(void) {} #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) static struct mtd_partition stamp_partitions[] = { { - .name = "Bootloader", + .name = "bootloader(nor)", .size = 0x40000, .offset = 0, }, { - .name = "Kernel", + .name = "linux kernel(nor)", .size = 0xE0000, .offset = MTDPART_OFS_APPEND, }, { - .name = "RootFS", + .name = "file system(nor)", .size = 0x400000 - 0x40000 - 0xE0000 - 0x10000, .offset = MTDPART_OFS_APPEND, }, { - .name = "MAC Address", + .name = "MAC Address(nor)", .size = MTDPART_SIZ_FULL, .offset = 0x3F0000, .mask_flags = MTD_WRITEABLE, @@ -485,16 +485,16 @@ static struct platform_device stamp_flash_device = { || defined(CONFIG_MTD_M25P80_MODULE) static struct mtd_partition bfin_spi_flash_partitions[] = { { - .name = "bootloader", + .name = "bootloader(spi)", .size = 0x00040000, .offset = 0, .mask_flags = MTD_CAP_ROM }, { - .name = "kernel", + .name = "linux kernel(spi)", .size = 0xe0000, .offset = MTDPART_OFS_APPEND, }, { - .name = "file system", + .name = "file system(spi)", .size = MTDPART_SIZ_FULL, .offset = MTDPART_OFS_APPEND, } diff --git a/arch/blackfin/mach-bf548/boards/cm_bf548.c b/arch/blackfin/mach-bf548/boards/cm_bf548.c index 4f4ae8787ed..58abbed0a22 100644 --- a/arch/blackfin/mach-bf548/boards/cm_bf548.c +++ b/arch/blackfin/mach-bf548/boards/cm_bf548.c @@ -319,12 +319,12 @@ static struct platform_device bfin_atapi_device = { #if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE) static struct mtd_partition partition_info[] = { { - .name = "Linux Kernel", + .name = "linux kernel(nand)", .offset = 0, .size = 4 * SIZE_1M, }, { - .name = "File System", + .name = "file system(nand)", .offset = 4 * SIZE_1M, .size = (256 - 4) * SIZE_1M, }, @@ -377,12 +377,12 @@ static struct platform_device bf54x_sdh_device = { /* SPI flash chip (m25p16) */ static struct mtd_partition bfin_spi_flash_partitions[] = { { - .name = "bootloader", + .name = "bootloader(spi)", .size = 0x00040000, .offset = 0, .mask_flags = MTD_CAP_ROM }, { - .name = "linux kernel", + .name = "linux kernel(spi)", .size = 0x1c0000, .offset = 0x40000 } diff --git a/arch/blackfin/mach-bf548/boards/ezkit.c b/arch/blackfin/mach-bf548/boards/ezkit.c index 166fa2201ee..0d6333ada1d 100644 --- a/arch/blackfin/mach-bf548/boards/ezkit.c +++ b/arch/blackfin/mach-bf548/boards/ezkit.c @@ -365,12 +365,12 @@ static struct platform_device bfin_atapi_device = { #if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE) static struct mtd_partition partition_info[] = { { - .name = "Linux Kernel", + .name = "linux kernel(nand)", .offset = 0, .size = 4 * SIZE_1M, }, { - .name = "File System", + .name = "file system(nand)", .offset = MTDPART_OFS_APPEND, .size = MTDPART_SIZ_FULL, }, @@ -419,15 +419,15 @@ static struct platform_device bf54x_sdh_device = { #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) static struct mtd_partition ezkit_partitions[] = { { - .name = "Bootloader", + .name = "bootloader(nor)", .size = 0x40000, .offset = 0, }, { - .name = "Kernel", + .name = "linux kernel(nor)", .size = 0x1C0000, .offset = MTDPART_OFS_APPEND, }, { - .name = "RootFS", + .name = "file system(nor)", .size = MTDPART_SIZ_FULL, .offset = MTDPART_OFS_APPEND, } @@ -461,12 +461,12 @@ static struct platform_device ezkit_flash_device = { /* SPI flash chip (m25p16) */ static struct mtd_partition bfin_spi_flash_partitions[] = { { - .name = "bootloader", + .name = "bootloader(spi)", .size = 0x00040000, .offset = 0, .mask_flags = MTD_CAP_ROM }, { - .name = "linux kernel", + .name = "linux kernel(spi)", .size = MTDPART_SIZ_FULL, .offset = MTDPART_OFS_APPEND, } diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c index 466ef5929a2..1309ec15b3c 100644 --- a/arch/blackfin/mach-bf561/boards/cm_bf561.c +++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c @@ -54,16 +54,16 @@ const char bfin_board_name[] = "Bluetechnix CM BF561"; #if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) static struct mtd_partition bfin_spi_flash_partitions[] = { { - .name = "bootloader", + .name = "bootloader(spi)", .size = 0x00020000, .offset = 0, .mask_flags = MTD_CAP_ROM }, { - .name = "kernel", + .name = "linux kernel(spi)", .size = 0xe0000, .offset = 0x20000 }, { - .name = "file system", + .name = "file system(spi)", .size = 0x700000, .offset = 0x00100000, } diff --git a/arch/blackfin/mach-bf561/boards/ezkit.c b/arch/blackfin/mach-bf561/boards/ezkit.c index bc6feded856..2affbdf2fb4 100644 --- a/arch/blackfin/mach-bf561/boards/ezkit.c +++ b/arch/blackfin/mach-bf561/boards/ezkit.c @@ -243,15 +243,15 @@ static struct platform_device bfin_sir_device = { #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) static struct mtd_partition ezkit_partitions[] = { { - .name = "Bootloader", + .name = "bootloader(nor)", .size = 0x40000, .offset = 0, }, { - .name = "Kernel", + .name = "linux kernel(nor)", .size = 0x1C0000, .offset = MTDPART_OFS_APPEND, }, { - .name = "RootFS", + .name = "file system(nor)", .size = MTDPART_SIZ_FULL, .offset = MTDPART_OFS_APPEND, } -- GitLab From 8ea8949733e35597efa45e71c0d3d65cafd7687a Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Tue, 5 Aug 2008 18:14:44 +0800 Subject: [PATCH 042/750] Blackfin arch: add board resources for parallel flash on cm-bf537 Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- arch/blackfin/mach-bf537/boards/cm_bf537.c | 54 ++++++++++++++++++++++ 1 file changed, 54 insertions(+) diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537.c b/arch/blackfin/mach-bf537/boards/cm_bf537.c index cb73ed5cc1a..fa6064f6d57 100644 --- a/arch/blackfin/mach-bf537/boards/cm_bf537.c +++ b/arch/blackfin/mach-bf537/boards/cm_bf537.c @@ -33,6 +33,7 @@ #include #include #include +#include #include #include #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) @@ -307,6 +308,55 @@ static struct platform_device net2272_bfin_device = { }; #endif +#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE) +static struct mtd_partition cm_partitions[] = { + { + .name = "bootloader(nor)", + .size = 0x40000, + .offset = 0, + }, { + .name = "linux kernel(nor)", + .size = 0xE0000, + .offset = MTDPART_OFS_APPEND, + }, { + .name = "file system(nor)", + .size = MTDPART_SIZ_FULL, + .offset = MTDPART_OFS_APPEND, + } +}; + +static struct physmap_flash_data cm_flash_data = { + .width = 2, + .parts = cm_partitions, + .nr_parts = ARRAY_SIZE(cm_partitions), +}; + +static unsigned cm_flash_gpios[] = { GPIO_PF4 }; + +static struct resource cm_flash_resource[] = { + { + .name = "cfi_probe", + .start = 0x20000000, + .end = 0x201fffff, + .flags = IORESOURCE_MEM, + }, { + .start = (unsigned long)cm_flash_gpios, + .end = ARRAY_SIZE(cm_flash_gpios), + .flags = IORESOURCE_IRQ, + } +}; + +static struct platform_device cm_flash_device = { + .name = "gpio-addr-flash", + .id = 0, + .dev = { + .platform_data = &cm_flash_data, + }, + .num_resources = ARRAY_SIZE(cm_flash_resource), + .resource = cm_flash_resource, +}; +#endif + #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) static struct resource bfin_uart_resources[] = { { @@ -510,6 +560,10 @@ static struct platform_device *cm_bf537_devices[] __initdata = { #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) &bfin_pata_device, #endif + +#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE) + &cm_flash_device, +#endif }; static int __init cm_bf537_init(void) -- GitLab From b9da3b9240f175a29274abb8a94d962b67bbabf6 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Wed, 13 Aug 2008 15:49:35 +0800 Subject: [PATCH 043/750] Blackfin arch: add support for board tcm-bf537 Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- arch/blackfin/configs/TCM-BF537_defconfig | 693 ++++++++++++++++++++ arch/blackfin/mach-bf537/boards/Kconfig | 6 + arch/blackfin/mach-bf537/boards/Makefile | 1 + arch/blackfin/mach-bf537/boards/tcm_bf537.c | 590 +++++++++++++++++ 4 files changed, 1290 insertions(+) create mode 100644 arch/blackfin/configs/TCM-BF537_defconfig create mode 100644 arch/blackfin/mach-bf537/boards/tcm_bf537.c diff --git a/arch/blackfin/configs/TCM-BF537_defconfig b/arch/blackfin/configs/TCM-BF537_defconfig new file mode 100644 index 00000000000..c482ee171f9 --- /dev/null +++ b/arch/blackfin/configs/TCM-BF537_defconfig @@ -0,0 +1,693 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.24.7 +# Thu Jul 31 00:53:15 2008 +# +# CONFIG_MMU is not set +# CONFIG_FPU is not set +CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set +CONFIG_BLACKFIN=y +CONFIG_ZONE_DMA=y +CONFIG_SEMAPHORE_SLEEPERS=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_GENERIC_GPIO=y +CONFIG_FORCE_MAX_ZONEORDER=14 +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +CONFIG_FAIR_GROUP_SCHED=y +CONFIG_FAIR_USER_SCHED=y +# CONFIG_FAIR_CGROUP_SCHED is not set +CONFIG_SYSFS_DEPRECATED=y +# CONFIG_RELAY is not set +# CONFIG_BLK_DEV_INITRD is not set +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +# CONFIG_UID16 is not set +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_EXTRA_PASS is not set +# CONFIG_HOTPLUG is not set +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_EVENTFD=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +CONFIG_TINY_SHMEM=y +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +# CONFIG_IOSCHED_AS is not set +# CONFIG_IOSCHED_DEADLINE is not set +CONFIG_IOSCHED_CFQ=y +# CONFIG_DEFAULT_AS is not set +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +CONFIG_DEFAULT_NOOP=y +CONFIG_DEFAULT_IOSCHED="noop" +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set + +# +# Blackfin Processor Options +# + +# +# Processor and Board Settings +# +# CONFIG_BF522 is not set +# CONFIG_BF523 is not set +# CONFIG_BF524 is not set +# CONFIG_BF525 is not set +# CONFIG_BF526 is not set +# CONFIG_BF527 is not set +# CONFIG_BF531 is not set +# CONFIG_BF532 is not set +# CONFIG_BF533 is not set +# CONFIG_BF534 is not set +# CONFIG_BF536 is not set +CONFIG_BF537=y +# CONFIG_BF542 is not set +# CONFIG_BF544 is not set +# CONFIG_BF547 is not set +# CONFIG_BF548 is not set +# CONFIG_BF549 is not set +# CONFIG_BF561 is not set +# CONFIG_BF_REV_0_0 is not set +# CONFIG_BF_REV_0_1 is not set +CONFIG_BF_REV_0_2=y +# CONFIG_BF_REV_0_3 is not set +# CONFIG_BF_REV_0_4 is not set +# CONFIG_BF_REV_0_5 is not set +# CONFIG_BF_REV_ANY is not set +# CONFIG_BF_REV_NONE is not set +CONFIG_BF53x=y +CONFIG_IRQ_PLL_WAKEUP=7 +CONFIG_IRQ_RTC=8 +CONFIG_IRQ_PPI=8 +CONFIG_IRQ_SPORT0_RX=9 +CONFIG_IRQ_SPORT0_TX=9 +CONFIG_IRQ_SPORT1_RX=9 +CONFIG_IRQ_SPORT1_TX=9 +CONFIG_IRQ_TWI=10 +CONFIG_IRQ_SPI=10 +CONFIG_IRQ_UART0_RX=10 +CONFIG_IRQ_UART0_TX=10 +CONFIG_IRQ_UART1_RX=10 +CONFIG_IRQ_UART1_TX=10 +CONFIG_IRQ_MAC_RX=11 +CONFIG_IRQ_MAC_TX=11 +CONFIG_IRQ_TMR0=12 +CONFIG_IRQ_TMR1=12 +CONFIG_IRQ_TMR2=12 +CONFIG_IRQ_TMR3=12 +CONFIG_IRQ_TMR4=12 +CONFIG_IRQ_TMR5=12 +CONFIG_IRQ_TMR6=12 +CONFIG_IRQ_TMR7=12 +CONFIG_IRQ_PORTG_INTB=12 +CONFIG_IRQ_MEM_DMA0=13 +CONFIG_IRQ_MEM_DMA1=13 +CONFIG_IRQ_WATCH=13 +# CONFIG_BFIN537_STAMP is not set +# CONFIG_BFIN537_BLUETECHNIX_CM is not set +CONFIG_BFIN537_BLUETECHNIX_TCM=y +# CONFIG_PNAV10 is not set +# CONFIG_CAMSIG_MINOTAUR is not set +# CONFIG_GENERIC_BF537_BOARD is not set + +# +# BF537 Specific Configuration +# + +# +# Interrupt Priority Assignment +# + +# +# Priority +# +CONFIG_IRQ_DMA_ERROR=7 +CONFIG_IRQ_ERROR=7 +CONFIG_IRQ_CAN_RX=11 +CONFIG_IRQ_CAN_TX=11 +CONFIG_IRQ_PROG_INTA=12 + +# +# Board customizations +# +# CONFIG_CMDLINE_BOOL is not set +CONFIG_BOOT_LOAD=0x1000 + +# +# Clock/PLL Setup +# +CONFIG_CLKIN_HZ=25000000 +# CONFIG_BFIN_KERNEL_CLOCK is not set +CONFIG_MAX_MEM_SIZE=32 +CONFIG_MAX_VCO_HZ=600000000 +CONFIG_MIN_VCO_HZ=50000000 +CONFIG_MAX_SCLK_HZ=133333333 +CONFIG_MIN_SCLK_HZ=27000000 + +# +# Kernel Timer/Scheduler +# +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_HZ_300 is not set +# CONFIG_HZ_1000 is not set +CONFIG_HZ=250 +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +# CONFIG_CYCLES_CLOCKSOURCE is not set +# CONFIG_TICK_ONESHOT is not set +# CONFIG_NO_HZ is not set +# CONFIG_HIGH_RES_TIMERS is not set +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y + +# +# Misc +# +CONFIG_BFIN_SCRATCH_REG_RETN=y +# CONFIG_BFIN_SCRATCH_REG_RETE is not set +# CONFIG_BFIN_SCRATCH_REG_CYCLES is not set + +# +# Blackfin Kernel Optimizations +# + +# +# Memory Optimizations +# +CONFIG_I_ENTRY_L1=y +CONFIG_EXCPT_IRQ_SYSC_L1=y +CONFIG_DO_IRQ_L1=y +CONFIG_CORE_TIMER_IRQ_L1=y +CONFIG_IDLE_L1=y +CONFIG_SCHEDULE_L1=y +CONFIG_ARITHMETIC_OPS_L1=y +CONFIG_ACCESS_OK_L1=y +CONFIG_MEMSET_L1=y +CONFIG_MEMCPY_L1=y +CONFIG_SYS_BFIN_SPINLOCK_L1=y +CONFIG_IP_CHECKSUM_L1=y +CONFIG_CACHELINE_ALIGNED_L1=y +CONFIG_SYSCALL_TAB_L1=y +CONFIG_CPLB_SWITCH_TAB_L1=y +CONFIG_RAMKERNEL=y +# CONFIG_ROMKERNEL is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_SPLIT_PTLOCK_CPUS=4 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_VIRT_TO_BUS=y +# CONFIG_BFIN_GPTIMERS is not set +CONFIG_BFIN_DMA_5XX=y +# CONFIG_DMA_UNCACHED_4M is not set +# CONFIG_DMA_UNCACHED_2M is not set +CONFIG_DMA_UNCACHED_1M=y +# CONFIG_DMA_UNCACHED_NONE is not set + +# +# Cache Support +# +CONFIG_BFIN_ICACHE=y +CONFIG_BFIN_DCACHE=y +# CONFIG_BFIN_DCACHE_BANKA is not set +# CONFIG_BFIN_ICACHE_LOCK is not set +CONFIG_BFIN_WB=y +# CONFIG_BFIN_WT is not set +# CONFIG_MPU is not set + +# +# Asynchonous Memory Configuration +# + +# +# EBIU_AMGCTL Global Control +# +CONFIG_C_AMCKEN=y +CONFIG_C_CDPRIO=y +# CONFIG_C_AMBEN is not set +# CONFIG_C_AMBEN_B0 is not set +# CONFIG_C_AMBEN_B0_B1 is not set +# CONFIG_C_AMBEN_B0_B1_B2 is not set +CONFIG_C_AMBEN_ALL=y + +# +# EBIU_AMBCTL Control +# +CONFIG_BANK_0=0x7BB0 +CONFIG_BANK_1=0x7BB0 +CONFIG_BANK_2=0x7BB0 +CONFIG_BANK_3=0xFFC2 + +# +# Bus options (PCI, PCMCIA, EISA, MCA, ISA) +# +# CONFIG_PCI is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set + +# +# Executable file formats +# +CONFIG_BINFMT_ELF_FDPIC=y +CONFIG_BINFMT_FLAT=y +CONFIG_BINFMT_ZFLAT=y +CONFIG_BINFMT_SHARED_FLAT=y +# CONFIG_BINFMT_MISC is not set + +# +# Power management options +# +# CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +# CONFIG_PM_WAKEUP_BY_GPIO is not set + +# +# CPU Frequency scaling +# +# CONFIG_CPU_FREQ is not set + +# +# Networking +# +# CONFIG_NET is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_SYS_HYPERVISOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +# CONFIG_MTD_CMDLINE_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +# CONFIG_MTD_CFI is not set +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +CONFIG_MTD_RAM=y +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_GPIO_ADDR is not set +CONFIG_MTD_UCLINUX=y +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_DATAFLASH is not set +# CONFIG_MTD_M25P80 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +# CONFIG_MTD_NAND is not set +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +# CONFIG_BLK_DEV_LOOP is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=4096 +CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 +# CONFIG_CDROM_PKTCDVD is not set +CONFIG_MISC_DEVICES=y +# CONFIG_EEPROM_93CX6 is not set +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set +# CONFIG_SCSI_DMA is not set +# CONFIG_SCSI_NETLINK is not set +# CONFIG_ATA is not set +# CONFIG_MD is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +# CONFIG_INPUT is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +# CONFIG_AD9960 is not set +# CONFIG_SPI_ADC_BF533 is not set +# CONFIG_BF5xx_PPIFCD is not set +# CONFIG_BFIN_SIMPLE_TIMER is not set +# CONFIG_BF5xx_PPI is not set +CONFIG_BFIN_SPORT=y +# CONFIG_BFIN_TIMER_LATENCY is not set +# CONFIG_SIMPLE_GPIO is not set +# CONFIG_VT is not set +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_BFIN=y +CONFIG_SERIAL_BFIN_CONSOLE=y +CONFIG_SERIAL_BFIN_DMA=y +# CONFIG_SERIAL_BFIN_PIO is not set +CONFIG_SERIAL_BFIN_UART0=y +# CONFIG_BFIN_UART0_CTSRTS is not set +CONFIG_SERIAL_BFIN_UART1=y +# CONFIG_BFIN_UART1_CTSRTS is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_BFIN_SPORT is not set +CONFIG_UNIX98_PTYS=y +# CONFIG_LEGACY_PTYS is not set + +# +# CAN, the car bus and industrial fieldbus +# +# CONFIG_CAN4LINUX is not set +# CONFIG_IPMI_HANDLER is not set +# CONFIG_HW_RANDOM is not set +# CONFIG_GEN_RTC is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +# CONFIG_I2C is not set + +# +# SPI support +# +CONFIG_SPI=y +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +CONFIG_SPI_BFIN=y +# CONFIG_SPI_BITBANG is not set + +# +# SPI Protocol Masters +# +# CONFIG_SPI_AT25 is not set +# CONFIG_SPI_SPIDEV is not set +# CONFIG_SPI_TLE62X0 is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_BFIN_WDT=y + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DAB is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Sound +# +# CONFIG_SOUND is not set +# CONFIG_USB_SUPPORT is not set +# CONFIG_MMC is not set +# CONFIG_NEW_LEDS is not set +# CONFIG_RTC_CLASS is not set + +# +# Userspace I/O +# +# CONFIG_UIO is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +CONFIG_EXT2_FS_XATTR=y +# CONFIG_EXT2_FS_POSIX_ACL is not set +# CONFIG_EXT2_FS_SECURITY is not set +# CONFIG_EXT3_FS is not set +# CONFIG_EXT4DEV_FS is not set +CONFIG_FS_MBCACHE=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_DNOTIFY is not set +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +# CONFIG_TMPFS is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_YAFFS_FS is not set +# CONFIG_JFFS2_FS is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y +# CONFIG_NLS is not set +# CONFIG_INSTRUMENTATION is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +CONFIG_DEBUG_FS=y +# CONFIG_HEADERS_CHECK is not set +# CONFIG_DEBUG_KERNEL is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_SAMPLES is not set +CONFIG_DEBUG_MMRS=y +CONFIG_DEBUG_HUNT_FOR_ZERO=y +CONFIG_DEBUG_BFIN_HWTRACE_ON=y +CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_OFF=y +# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_ONE is not set +# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_TWO is not set +CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION=0 +# CONFIG_DEBUG_BFIN_HWTRACE_EXPAND is not set +# CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE is not set +# CONFIG_EARLY_PRINTK is not set +CONFIG_CPLB_INFO=y +CONFIG_ACCESS_CHECK=y + +# +# Security options +# +# CONFIG_KEYS is not set +CONFIG_SECURITY=y +# CONFIG_SECURITY_NETWORK is not set +CONFIG_SECURITY_CAPABILITIES=y +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +# CONFIG_CRYPTO is not set + +# +# Library routines +# +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +# CONFIG_CRC_ITU_T is not set +# CONFIG_CRC32 is not set +# CONFIG_CRC7 is not set +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y diff --git a/arch/blackfin/mach-bf537/boards/Kconfig b/arch/blackfin/mach-bf537/boards/Kconfig index 7e789dbef03..42a57b0acb2 100644 --- a/arch/blackfin/mach-bf537/boards/Kconfig +++ b/arch/blackfin/mach-bf537/boards/Kconfig @@ -15,6 +15,12 @@ config BFIN537_BLUETECHNIX_CM help CM-BF537 support for EVAL- and DEV-Board. +config BFIN537_BLUETECHNIX_TCM + bool "Bluetechnix TCM-BF537" + depends on (BF537) + help + TCM-BF537 support for EVAL- and DEV-Board. + config PNAV10 bool "PNAV board" depends on (BF537) diff --git a/arch/blackfin/mach-bf537/boards/Makefile b/arch/blackfin/mach-bf537/boards/Makefile index c94f7a5b821..7168cc14afd 100644 --- a/arch/blackfin/mach-bf537/boards/Makefile +++ b/arch/blackfin/mach-bf537/boards/Makefile @@ -5,5 +5,6 @@ obj-$(CONFIG_GENERIC_BF537_BOARD) += generic_board.o obj-$(CONFIG_BFIN537_STAMP) += stamp.o obj-$(CONFIG_BFIN537_BLUETECHNIX_CM) += cm_bf537.o +obj-$(CONFIG_BFIN537_BLUETECHNIX_TCM) += tcm_bf537.o obj-$(CONFIG_PNAV10) += pnav10.o obj-$(CONFIG_CAMSIG_MINOTAUR) += minotaur.o diff --git a/arch/blackfin/mach-bf537/boards/tcm_bf537.c b/arch/blackfin/mach-bf537/boards/tcm_bf537.c new file mode 100644 index 00000000000..196e5775a6a --- /dev/null +++ b/arch/blackfin/mach-bf537/boards/tcm_bf537.c @@ -0,0 +1,590 @@ +/* + * File: arch/blackfin/mach-bf537/boards/tcm_bf537.c + * Based on: arch/blackfin/mach-bf533/boards/cm_bf537.c + * Author: Aidan Williams + * + * Created: 2005 + * Description: Board description file + * + * Modified: + * Copyright 2005 National ICT Australia (NICTA) + * Copyright 2004-2006 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) +#include +#endif +#include +#include +#include +#include +#include +#include + +/* + * Name the Board for the /proc/cpuinfo + */ +const char bfin_board_name[] = "Bluetechnix TCM BF537"; + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +/* all SPI peripherals info goes here */ + +#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) +static struct mtd_partition bfin_spi_flash_partitions[] = { + { + .name = "bootloader(spi)", + .size = 0x00020000, + .offset = 0, + .mask_flags = MTD_CAP_ROM + }, { + .name = "linux kernel(spi)", + .size = 0xe0000, + .offset = 0x20000 + }, { + .name = "file system(spi)", + .size = 0x700000, + .offset = 0x00100000, + } +}; + +static struct flash_platform_data bfin_spi_flash_data = { + .name = "m25p80", + .parts = bfin_spi_flash_partitions, + .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions), + .type = "m25p64", +}; + +/* SPI flash chip (m25p64) */ +static struct bfin5xx_spi_chip spi_flash_chip_info = { + .enable_dma = 0, /* use dma transfer with this chip*/ + .bits_per_word = 8, +}; +#endif + +#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE) +/* SPI ADC chip */ +static struct bfin5xx_spi_chip spi_adc_chip_info = { + .enable_dma = 1, /* use dma transfer with this chip*/ + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) +static struct bfin5xx_spi_chip ad1836_spi_chip_info = { + .enable_dma = 0, + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE) +static struct bfin5xx_spi_chip ad9960_spi_chip_info = { + .enable_dma = 0, + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE) +static struct bfin5xx_spi_chip spi_mmc_chip_info = { + .enable_dma = 1, + .bits_per_word = 8, +}; +#endif + +static struct spi_board_info bfin_spi_board_info[] __initdata = { +#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) + { + /* the modalias must be the same as spi device driver name */ + .modalias = "m25p80", /* Name of spi_driver for this device */ + .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, /* Framework bus number */ + .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/ + .platform_data = &bfin_spi_flash_data, + .controller_data = &spi_flash_chip_info, + .mode = SPI_MODE_3, + }, +#endif + +#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE) + { + .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */ + .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, /* Framework bus number */ + .chip_select = 1, /* Framework chip select. */ + .platform_data = NULL, /* No spi_driver specific config */ + .controller_data = &spi_adc_chip_info, + }, +#endif + +#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) + { + .modalias = "ad1836-spi", + .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT, + .controller_data = &ad1836_spi_chip_info, + }, +#endif + +#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE) + { + .modalias = "ad9960-spi", + .max_speed_hz = 10000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 1, + .controller_data = &ad9960_spi_chip_info, + }, +#endif + +#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE) + { + .modalias = "spi_mmc_dummy", + .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 7, + .platform_data = NULL, + .controller_data = &spi_mmc_chip_info, + .mode = SPI_MODE_3, + }, + { + .modalias = "spi_mmc", + .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = CONFIG_SPI_MMC_CS_CHAN, + .platform_data = NULL, + .controller_data = &spi_mmc_chip_info, + .mode = SPI_MODE_3, + }, +#endif +}; + +/* SPI (0) */ +static struct resource bfin_spi0_resource[] = { + [0] = { + .start = SPI0_REGBASE, + .end = SPI0_REGBASE + 0xFF, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = CH_SPI, + .end = CH_SPI, + .flags = IORESOURCE_IRQ, + } +}; + +/* SPI controller data */ +static struct bfin5xx_spi_master bfin_spi0_info = { + .num_chipselect = 8, + .enable_dma = 1, /* master has the ability to do dma transfer */ + .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0}, +}; + +static struct platform_device bfin_spi0_device = { + .name = "bfin-spi", + .id = 0, /* Bus number */ + .num_resources = ARRAY_SIZE(bfin_spi0_resource), + .resource = bfin_spi0_resource, + .dev = { + .platform_data = &bfin_spi0_info, /* Passed to driver */ + }, +}; +#endif /* spi master and devices */ + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) +static struct platform_device rtc_device = { + .name = "rtc-bfin", + .id = -1, +}; +#endif + +#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE) +static struct platform_device hitachi_fb_device = { + .name = "hitachi-tx09", +}; +#endif + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) +static struct resource smc91x_resources[] = { + { + .start = 0x20200300, + .end = 0x20200300 + 16, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_PF14, + .end = IRQ_PF14, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct platform_device smc91x_device = { + .name = "smc91x", + .id = 0, + .num_resources = ARRAY_SIZE(smc91x_resources), + .resource = smc91x_resources, +}; +#endif + +#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) +static struct resource isp1362_hcd_resources[] = { + { + .start = 0x20308000, + .end = 0x20308000, + .flags = IORESOURCE_MEM, + }, { + .start = 0x20308004, + .end = 0x20308004, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_PG15, + .end = IRQ_PG15, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct isp1362_platform_data isp1362_priv = { + .sel15Kres = 1, + .clknotstop = 0, + .oc_enable = 0, + .int_act_high = 0, + .int_edge_triggered = 0, + .remote_wakeup_connected = 0, + .no_power_switching = 1, + .power_switching_mode = 0, +}; + +static struct platform_device isp1362_hcd_device = { + .name = "isp1362-hcd", + .id = 0, + .dev = { + .platform_data = &isp1362_priv, + }, + .num_resources = ARRAY_SIZE(isp1362_hcd_resources), + .resource = isp1362_hcd_resources, +}; +#endif + +#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) +static struct resource net2272_bfin_resources[] = { + { + .start = 0x20200000, + .end = 0x20200000 + 0x100, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_PH14, + .end = IRQ_PH14, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct platform_device net2272_bfin_device = { + .name = "net2272", + .id = -1, + .num_resources = ARRAY_SIZE(net2272_bfin_resources), + .resource = net2272_bfin_resources, +}; +#endif + +#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE) +static struct mtd_partition cm_partitions[] = { + { + .name = "bootloader(nor)", + .size = 0x40000, + .offset = 0, + }, { + .name = "linux kernel(nor)", + .size = 0xE0000, + .offset = MTDPART_OFS_APPEND, + }, { + .name = "file system(nor)", + .size = MTDPART_SIZ_FULL, + .offset = MTDPART_OFS_APPEND, + } +}; + +static struct physmap_flash_data cm_flash_data = { + .width = 2, + .parts = cm_partitions, + .nr_parts = ARRAY_SIZE(cm_partitions), +}; + +static unsigned cm_flash_gpios[] = { GPIO_PF4, GPIO_PF5 }; + +static struct resource cm_flash_resource[] = { + { + .name = "cfi_probe", + .start = 0x20000000, + .end = 0x201fffff, + .flags = IORESOURCE_MEM, + }, { + .start = (unsigned long)cm_flash_gpios, + .end = ARRAY_SIZE(cm_flash_gpios), + .flags = IORESOURCE_IRQ, + } +}; + +static struct platform_device cm_flash_device = { + .name = "gpio-addr-flash", + .id = 0, + .dev = { + .platform_data = &cm_flash_data, + }, + .num_resources = ARRAY_SIZE(cm_flash_resource), + .resource = cm_flash_resource, +}; +#endif + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) +static struct resource bfin_uart_resources[] = { + { + .start = 0xFFC00400, + .end = 0xFFC004FF, + .flags = IORESOURCE_MEM, + }, { + .start = 0xFFC02000, + .end = 0xFFC020FF, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device bfin_uart_device = { + .name = "bfin-uart", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_uart_resources), + .resource = bfin_uart_resources, +}; +#endif + +#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) +static struct resource bfin_sir_resources[] = { +#ifdef CONFIG_BFIN_SIR0 + { + .start = 0xFFC00400, + .end = 0xFFC004FF, + .flags = IORESOURCE_MEM, + }, +#endif +#ifdef CONFIG_BFIN_SIR1 + { + .start = 0xFFC02000, + .end = 0xFFC020FF, + .flags = IORESOURCE_MEM, + }, +#endif +}; + +static struct platform_device bfin_sir_device = { + .name = "bfin_sir", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_sir_resources), + .resource = bfin_sir_resources, +}; +#endif + +#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) +static struct resource bfin_twi0_resource[] = { + [0] = { + .start = TWI0_REGBASE, + .end = TWI0_REGBASE, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_TWI, + .end = IRQ_TWI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device i2c_bfin_twi_device = { + .name = "i2c-bfin-twi", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_twi0_resource), + .resource = bfin_twi0_resource, +}; +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) +static struct platform_device bfin_sport0_uart_device = { + .name = "bfin-sport-uart", + .id = 0, +}; + +static struct platform_device bfin_sport1_uart_device = { + .name = "bfin-sport-uart", + .id = 1, +}; +#endif + +#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) +static struct platform_device bfin_mac_device = { + .name = "bfin_mac", +}; +#endif + +#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) +#define PATA_INT 64 + +static struct pata_platform_info bfin_pata_platform_data = { + .ioport_shift = 2, + .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED, +}; + +static struct resource bfin_pata_resources[] = { + { + .start = 0x2030C000, + .end = 0x2030C01F, + .flags = IORESOURCE_MEM, + }, + { + .start = 0x2030D018, + .end = 0x2030D01B, + .flags = IORESOURCE_MEM, + }, + { + .start = PATA_INT, + .end = PATA_INT, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bfin_pata_device = { + .name = "pata_platform", + .id = -1, + .num_resources = ARRAY_SIZE(bfin_pata_resources), + .resource = bfin_pata_resources, + .dev = { + .platform_data = &bfin_pata_platform_data, + } +}; +#endif + +static const unsigned int cclk_vlev_datasheet[] = +{ + VRPAIR(VLEV_085, 250000000), + VRPAIR(VLEV_090, 376000000), + VRPAIR(VLEV_095, 426000000), + VRPAIR(VLEV_100, 426000000), + VRPAIR(VLEV_105, 476000000), + VRPAIR(VLEV_110, 476000000), + VRPAIR(VLEV_115, 476000000), + VRPAIR(VLEV_120, 500000000), + VRPAIR(VLEV_125, 533000000), + VRPAIR(VLEV_130, 600000000), +}; + +static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = { + .tuple_tab = cclk_vlev_datasheet, + .tabsize = ARRAY_SIZE(cclk_vlev_datasheet), + .vr_settling_time = 25 /* us */, +}; + +static struct platform_device bfin_dpmc = { + .name = "bfin dpmc", + .dev = { + .platform_data = &bfin_dmpc_vreg_data, + }, +}; + +static struct platform_device *cm_bf537_devices[] __initdata = { + + &bfin_dpmc, + +#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE) + &hitachi_fb_device, +#endif + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) + &rtc_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) + &bfin_uart_device, +#endif + +#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) + &bfin_sir_device, +#endif + +#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) + &i2c_bfin_twi_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) + &bfin_sport0_uart_device, + &bfin_sport1_uart_device, +#endif + +#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) + &isp1362_hcd_device, +#endif + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) + &smc91x_device, +#endif + +#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) + &bfin_mac_device, +#endif + +#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) + &net2272_bfin_device, +#endif + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + &bfin_spi0_device, +#endif + +#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) + &bfin_pata_device, +#endif + +#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE) + &cm_flash_device, +#endif +}; + +static int __init cm_bf537_init(void) +{ + printk(KERN_INFO "%s(): registering device resources\n", __func__); + platform_add_devices(cm_bf537_devices, ARRAY_SIZE(cm_bf537_devices)); +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); +#endif + +#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) + irq_desc[PATA_INT].status |= IRQ_NOAUTOEN; +#endif + return 0; +} + +arch_initcall(cm_bf537_init); + +void bfin_get_ether_addr(char *addr) +{ + random_ether_addr(addr); + printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__); +} +EXPORT_SYMBOL(bfin_get_ether_addr); -- GitLab From 908089118dd5b20c6694e9543fccd9b2490b1c6b Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Tue, 5 Aug 2008 18:41:20 +0800 Subject: [PATCH 044/750] Blackfin arch: remove pata resources from generic board these are highly board specific, so putting into generic doesnt make much sense Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- arch/blackfin/mach-bf527/boards/cm_bf527.c | 46 ------------------- arch/blackfin/mach-bf527/boards/ezkit.c | 46 ------------------- arch/blackfin/mach-bf533/boards/H8606.c | 1 - arch/blackfin/mach-bf533/boards/cm_bf533.c | 46 ------------------- arch/blackfin/mach-bf533/boards/ezkit.c | 46 ------------------- arch/blackfin/mach-bf533/boards/stamp.c | 46 ------------------- .../mach-bf537/boards/generic_board.c | 45 ------------------ arch/blackfin/mach-bf561/boards/ezkit.c | 46 ------------------- 8 files changed, 322 deletions(-) diff --git a/arch/blackfin/mach-bf527/boards/cm_bf527.c b/arch/blackfin/mach-bf527/boards/cm_bf527.c index 749f4a806b5..d22bc777371 100644 --- a/arch/blackfin/mach-bf527/boards/cm_bf527.c +++ b/arch/blackfin/mach-bf527/boards/cm_bf527.c @@ -39,7 +39,6 @@ #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) #include #endif -#include #include #include #include @@ -799,43 +798,6 @@ static struct platform_device bfin_sport1_uart_device = { }; #endif -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) -#define PATA_INT 55 - -static struct pata_platform_info bfin_pata_platform_data = { - .ioport_shift = 1, - .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED, -}; - -static struct resource bfin_pata_resources[] = { - { - .start = 0x20314020, - .end = 0x2031403F, - .flags = IORESOURCE_MEM, - }, - { - .start = 0x2031401C, - .end = 0x2031401F, - .flags = IORESOURCE_MEM, - }, - { - .start = PATA_INT, - .end = PATA_INT, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device bfin_pata_device = { - .name = "pata_platform", - .id = -1, - .num_resources = ARRAY_SIZE(bfin_pata_resources), - .resource = bfin_pata_resources, - .dev = { - .platform_data = &bfin_pata_platform_data, - } -}; -#endif - #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) #include #include @@ -961,10 +923,6 @@ static struct platform_device *stamp_devices[] __initdata = { &bfin_sport1_uart_device, #endif -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) - &bfin_pata_device, -#endif - #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) &bfin_device_gpiokeys, #endif @@ -987,10 +945,6 @@ static int __init stamp_init(void) platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices)); spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); - -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) - irq_desc[PATA_INT].status |= IRQ_NOAUTOEN; -#endif return 0; } diff --git a/arch/blackfin/mach-bf527/boards/ezkit.c b/arch/blackfin/mach-bf527/boards/ezkit.c index cbd47bce689..762f754c06c 100644 --- a/arch/blackfin/mach-bf527/boards/ezkit.c +++ b/arch/blackfin/mach-bf527/boards/ezkit.c @@ -38,7 +38,6 @@ #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) #include #endif -#include #include #include #include @@ -825,43 +824,6 @@ static struct platform_device bfin_sport1_uart_device = { }; #endif -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) -#define PATA_INT 55 - -static struct pata_platform_info bfin_pata_platform_data = { - .ioport_shift = 1, - .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED, -}; - -static struct resource bfin_pata_resources[] = { - { - .start = 0x20314020, - .end = 0x2031403F, - .flags = IORESOURCE_MEM, - }, - { - .start = 0x2031401C, - .end = 0x2031401F, - .flags = IORESOURCE_MEM, - }, - { - .start = PATA_INT, - .end = PATA_INT, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device bfin_pata_device = { - .name = "pata_platform", - .id = -1, - .num_resources = ARRAY_SIZE(bfin_pata_resources), - .resource = bfin_pata_resources, - .dev = { - .platform_data = &bfin_pata_platform_data, - } -}; -#endif - #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) #include #include @@ -996,10 +958,6 @@ static struct platform_device *stamp_devices[] __initdata = { &bfin_sport1_uart_device, #endif -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) - &bfin_pata_device, -#endif - #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) &bfin_device_gpiokeys, #endif @@ -1022,10 +980,6 @@ static int __init stamp_init(void) platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices)); spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); - -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) - irq_desc[PATA_INT].status |= IRQ_NOAUTOEN; -#endif return 0; } diff --git a/arch/blackfin/mach-bf533/boards/H8606.c b/arch/blackfin/mach-bf533/boards/H8606.c index cecbc624e3d..c66a68f3023 100644 --- a/arch/blackfin/mach-bf533/boards/H8606.c +++ b/arch/blackfin/mach-bf533/boards/H8606.c @@ -38,7 +38,6 @@ #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) #include #endif -#include #include #include diff --git a/arch/blackfin/mach-bf533/boards/cm_bf533.c b/arch/blackfin/mach-bf533/boards/cm_bf533.c index dfccf826fa3..575843f6d9e 100644 --- a/arch/blackfin/mach-bf533/boards/cm_bf533.c +++ b/arch/blackfin/mach-bf533/boards/cm_bf533.c @@ -36,7 +36,6 @@ #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) #include #endif -#include #include #include #include @@ -307,43 +306,6 @@ static struct platform_device isp1362_hcd_device = { }; #endif -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) -#define PATA_INT 38 - -static struct pata_platform_info bfin_pata_platform_data = { - .ioport_shift = 2, - .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED, -}; - -static struct resource bfin_pata_resources[] = { - { - .start = 0x2030C000, - .end = 0x2030C01F, - .flags = IORESOURCE_MEM, - }, - { - .start = 0x2030D018, - .end = 0x2030D01B, - .flags = IORESOURCE_MEM, - }, - { - .start = PATA_INT, - .end = PATA_INT, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device bfin_pata_device = { - .name = "pata_platform", - .id = -1, - .num_resources = ARRAY_SIZE(bfin_pata_resources), - .resource = bfin_pata_resources, - .dev = { - .platform_data = &bfin_pata_platform_data, - } -}; -#endif - static const unsigned int cclk_vlev_datasheet[] = { VRPAIR(VLEV_085, 250000000), @@ -403,10 +365,6 @@ static struct platform_device *cm_bf533_devices[] __initdata = { #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) &bfin_spi0_device, #endif - -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) - &bfin_pata_device, -#endif }; static int __init cm_bf533_init(void) @@ -416,10 +374,6 @@ static int __init cm_bf533_init(void) #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); #endif - -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) - irq_desc[PATA_INT].status |= IRQ_NOAUTOEN; -#endif return 0; } diff --git a/arch/blackfin/mach-bf533/boards/ezkit.c b/arch/blackfin/mach-bf533/boards/ezkit.c index 6a34f1519c0..cc2e7eeb1d5 100644 --- a/arch/blackfin/mach-bf533/boards/ezkit.c +++ b/arch/blackfin/mach-bf533/boards/ezkit.c @@ -37,7 +37,6 @@ #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) #include #endif -#include #include #include #include @@ -255,43 +254,6 @@ static struct platform_device bfin_sir_device = { }; #endif -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) -#define PATA_INT 55 - -static struct pata_platform_info bfin_pata_platform_data = { - .ioport_shift = 1, - .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED, -}; - -static struct resource bfin_pata_resources[] = { - { - .start = 0x20314020, - .end = 0x2031403F, - .flags = IORESOURCE_MEM, - }, - { - .start = 0x2031401C, - .end = 0x2031401F, - .flags = IORESOURCE_MEM, - }, - { - .start = PATA_INT, - .end = PATA_INT, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device bfin_pata_device = { - .name = "pata_platform", - .id = -1, - .num_resources = ARRAY_SIZE(bfin_pata_resources), - .resource = bfin_pata_resources, - .dev = { - .platform_data = &bfin_pata_platform_data, - } -}; -#endif - #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) #include #include @@ -404,10 +366,6 @@ static struct platform_device *ezkit_devices[] __initdata = { &bfin_sir_device, #endif -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) - &bfin_pata_device, -#endif - #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) &bfin_device_gpiokeys, #endif @@ -424,10 +382,6 @@ static int __init ezkit_init(void) printk(KERN_INFO "%s(): registering device resources\n", __func__); platform_add_devices(ezkit_devices, ARRAY_SIZE(ezkit_devices)); spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); - -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) - irq_desc[PATA_INT].status |= IRQ_NOAUTOEN; -#endif return 0; } diff --git a/arch/blackfin/mach-bf533/boards/stamp.c b/arch/blackfin/mach-bf533/boards/stamp.c index d10b2dc5902..050ffca5353 100644 --- a/arch/blackfin/mach-bf533/boards/stamp.c +++ b/arch/blackfin/mach-bf533/boards/stamp.c @@ -38,7 +38,6 @@ #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) #include #endif -#include #include #include #include @@ -404,43 +403,6 @@ static struct platform_device bfin_sport1_uart_device = { }; #endif -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) -#define PATA_INT 55 - -static struct pata_platform_info bfin_pata_platform_data = { - .ioport_shift = 1, - .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED, -}; - -static struct resource bfin_pata_resources[] = { - { - .start = 0x20314020, - .end = 0x2031403F, - .flags = IORESOURCE_MEM, - }, - { - .start = 0x2031401C, - .end = 0x2031401F, - .flags = IORESOURCE_MEM, - }, - { - .start = PATA_INT, - .end = PATA_INT, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device bfin_pata_device = { - .name = "pata_platform", - .id = -1, - .num_resources = ARRAY_SIZE(bfin_pata_resources), - .resource = bfin_pata_resources, - .dev = { - .platform_data = &bfin_pata_platform_data, - } -}; -#endif - #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) #include #include @@ -583,10 +545,6 @@ static struct platform_device *stamp_devices[] __initdata = { &bfin_sport1_uart_device, #endif -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) - &bfin_pata_device, -#endif - #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) &bfin_device_gpiokeys, #endif @@ -625,10 +583,6 @@ static int __init stamp_init(void) #endif spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); - -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) - irq_desc[PATA_INT].status |= IRQ_NOAUTOEN; -#endif return 0; } diff --git a/arch/blackfin/mach-bf537/boards/generic_board.c b/arch/blackfin/mach-bf537/boards/generic_board.c index f5bc9258f83..78a13d5bfd5 100644 --- a/arch/blackfin/mach-bf537/boards/generic_board.c +++ b/arch/blackfin/mach-bf537/boards/generic_board.c @@ -38,7 +38,6 @@ #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) #include #endif -#include #include #include #include @@ -619,43 +618,6 @@ static struct platform_device bfin_sport1_uart_device = { }; #endif -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) -#define PATA_INT 55 - -static struct pata_platform_info bfin_pata_platform_data = { - .ioport_shift = 1, - .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED, -}; - -static struct resource bfin_pata_resources[] = { - { - .start = 0x20314020, - .end = 0x2031403F, - .flags = IORESOURCE_MEM, - }, - { - .start = 0x2031401C, - .end = 0x2031401F, - .flags = IORESOURCE_MEM, - }, - { - .start = PATA_INT, - .end = PATA_INT, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device bfin_pata_device = { - .name = "pata_platform", - .id = -1, - .num_resources = ARRAY_SIZE(bfin_pata_resources), - .resource = bfin_pata_resources, - .dev = { - .platform_data = &bfin_pata_platform_data, - } -}; -#endif - static struct platform_device *stamp_devices[] __initdata = { #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE) &bfin_pcmcia_cf_device, @@ -717,10 +679,6 @@ static struct platform_device *stamp_devices[] __initdata = { &bfin_sport0_uart_device, &bfin_sport1_uart_device, #endif - -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) - &bfin_pata_device, -#endif }; static int __init stamp_init(void) @@ -732,9 +690,6 @@ static int __init stamp_init(void) ARRAY_SIZE(bfin_spi_board_info)); #endif -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) - irq_desc[PATA_INT].status |= IRQ_NOAUTOEN; -#endif return 0; } diff --git a/arch/blackfin/mach-bf561/boards/ezkit.c b/arch/blackfin/mach-bf561/boards/ezkit.c index 2affbdf2fb4..50b4cdceccf 100644 --- a/arch/blackfin/mach-bf561/boards/ezkit.c +++ b/arch/blackfin/mach-bf561/boards/ezkit.c @@ -35,7 +35,6 @@ #include #include #include -#include #include #include #include @@ -350,43 +349,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = { #endif }; -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) -#define PATA_INT 55 - -static struct pata_platform_info bfin_pata_platform_data = { - .ioport_shift = 1, - .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED, -}; - -static struct resource bfin_pata_resources[] = { - { - .start = 0x20314020, - .end = 0x2031403F, - .flags = IORESOURCE_MEM, - }, - { - .start = 0x2031401C, - .end = 0x2031401F, - .flags = IORESOURCE_MEM, - }, - { - .start = PATA_INT, - .end = PATA_INT, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device bfin_pata_device = { - .name = "pata_platform", - .id = -1, - .num_resources = ARRAY_SIZE(bfin_pata_resources), - .resource = bfin_pata_resources, - .dev = { - .platform_data = &bfin_pata_platform_data, - } -}; -#endif - #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) #include #include @@ -499,10 +461,6 @@ static struct platform_device *ezkit_devices[] __initdata = { &bfin_sir_device, #endif -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) - &bfin_pata_device, -#endif - #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) &bfin_device_gpiokeys, #endif @@ -538,10 +496,6 @@ static int __init ezkit_init(void) #endif spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); - -#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) - irq_desc[PATA_INT].status |= IRQ_NOAUTOEN; -#endif return 0; } -- GitLab From fe5aeb93024791a5aa69741015db33093198ff47 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Tue, 5 Aug 2008 18:29:56 +0800 Subject: [PATCH 045/750] Blackfin arch: use symbolic IRQ_PF define rather than hardcoded Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- arch/blackfin/mach-bf537/boards/cm_bf537.c | 2 +- arch/blackfin/mach-bf537/boards/tcm_bf537.c | 2 +- arch/blackfin/mach-bf561/boards/cm_bf561.c | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537.c b/arch/blackfin/mach-bf537/boards/cm_bf537.c index fa6064f6d57..dde14720b0e 100644 --- a/arch/blackfin/mach-bf537/boards/cm_bf537.c +++ b/arch/blackfin/mach-bf537/boards/cm_bf537.c @@ -445,7 +445,7 @@ static struct platform_device bfin_mac_device = { #endif #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) -#define PATA_INT 64 +#define PATA_INT IRQ_PF14 static struct pata_platform_info bfin_pata_platform_data = { .ioport_shift = 2, diff --git a/arch/blackfin/mach-bf537/boards/tcm_bf537.c b/arch/blackfin/mach-bf537/boards/tcm_bf537.c index 196e5775a6a..d5ff705a512 100644 --- a/arch/blackfin/mach-bf537/boards/tcm_bf537.c +++ b/arch/blackfin/mach-bf537/boards/tcm_bf537.c @@ -445,7 +445,7 @@ static struct platform_device bfin_mac_device = { #endif #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) -#define PATA_INT 64 +#define PATA_INT IRQ_PF14 static struct pata_platform_info bfin_pata_platform_data = { .ioport_shift = 2, diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c index 1309ec15b3c..8f40990eea2 100644 --- a/arch/blackfin/mach-bf561/boards/cm_bf561.c +++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c @@ -306,7 +306,7 @@ static struct platform_device bfin_sir_device = { #endif #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) -#define PATA_INT 119 +#define PATA_INT IRQ_PF46 static struct pata_platform_info bfin_pata_platform_data = { .ioport_shift = 2, -- GitLab From d6a29891369827317659b7833170d2f5f0c7b97f Mon Sep 17 00:00:00 2001 From: Sonic Zhang Date: Tue, 5 Aug 2008 18:28:26 +0800 Subject: [PATCH 046/750] Blackfin arch: Fix bugs - Make kgdb code apparent to app debugging. - Skip single step if global interrupt disable bit is set. - Extend bernds' patch r4673 to skip single step in any interrupt entry that interrupts the code which is under single stepping. Bernds' patch only allow user space single stepping. Singed-off-by: Sonic Zhang Signed-off-by: Bryan Wu --- arch/blackfin/mach-common/entry.S | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) diff --git a/arch/blackfin/mach-common/entry.S b/arch/blackfin/mach-common/entry.S index 3db2f4df261..4bd971e81f1 100644 --- a/arch/blackfin/mach-common/entry.S +++ b/arch/blackfin/mach-common/entry.S @@ -163,6 +163,8 @@ ENTRY(_ex_single_step) p5.l = lo(IPEND); p5.h = hi(IPEND); r6 = [p5]; + cc = bittst(r6, 4); + if cc jump _bfin_return_from_exception; cc = bittst(r6, 5); if cc jump _bfin_return_from_exception; @@ -186,10 +188,9 @@ ENTRY(_ex_single_step) if cc jump .Ldo_single_step; r6 += -1; cc = r6 < r7; - if cc jump _bfin_return_from_exception; + if cc jump 1f; .Ldo_single_step: -#endif - +#else /* If we were in user mode, do the single step normally. */ p5.l = lo(IPEND); p5.h = hi(IPEND); @@ -198,6 +199,7 @@ ENTRY(_ex_single_step) r7 = r7 & r6; cc = r7 == 0; if !cc jump 1f; +#endif /* Single stepping only a single instruction, so clear the trace * bit here. */ -- GitLab From 778307d372555f979cf6cef112a6d7fbff056cd9 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Wed, 6 Aug 2008 17:05:20 +0800 Subject: [PATCH 047/750] Blackfin arch: remove support for Anomaly 05000125 as it doesnt exist on any supported processor/silicon Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- arch/blackfin/mach-bf527/head.S | 19 ----- arch/blackfin/mach-bf533/head.S | 18 ----- arch/blackfin/mach-bf537/head.S | 39 +--------- arch/blackfin/mach-bf561/head.S | 17 ---- arch/blackfin/mach-common/Makefile | 2 +- arch/blackfin/mach-common/cacheinit.S | 77 ------------------- .../mach-common/cdef_LPBlackfin.h | 8 -- 7 files changed, 2 insertions(+), 178 deletions(-) delete mode 100644 arch/blackfin/mach-common/cacheinit.S diff --git a/arch/blackfin/mach-bf527/head.S b/arch/blackfin/mach-bf527/head.S index fe05cc1ef17..a16a2657528 100644 --- a/arch/blackfin/mach-bf527/head.S +++ b/arch/blackfin/mach-bf527/head.S @@ -105,17 +105,8 @@ ENTRY(__start) R1 = [p0]; R0 = ~ENICPLB; R0 = R0 & R1; - - /* Anomaly 05000125 */ -#if ANOMALY_05000125 - CLI R2; - SSYNC; -#endif [p0] = R0; SSYNC; -#if ANOMALY_05000125 - STI R2; -#endif /* Turn off the dcache */ p0.l = LO(DMEM_CONTROL); @@ -123,18 +114,8 @@ ENTRY(__start) R1 = [p0]; R0 = ~ENDCPLB; R0 = R0 & R1; - - /* Anomaly 05000125 */ -#if ANOMALY_05000125 - CLI R2; - SSYNC; -#endif [p0] = R0; SSYNC; -#if ANOMALY_05000125 - STI R2; -#endif - #if defined(CONFIG_BF527) p0.h = hi(EMAC_SYSTAT); diff --git a/arch/blackfin/mach-bf533/head.S b/arch/blackfin/mach-bf533/head.S index c671e8549b1..fb49169c0e7 100644 --- a/arch/blackfin/mach-bf533/head.S +++ b/arch/blackfin/mach-bf533/head.S @@ -116,17 +116,8 @@ ENTRY(__start) R1 = [p0]; R0 = ~ENICPLB; R0 = R0 & R1; - - /* Anomaly 05000125 */ -#if ANOMALY_05000125 - CLI R2; - SSYNC; -#endif [p0] = R0; SSYNC; -#if ANOMALY_05000125 - STI R2; -#endif /* Turn off the dcache */ p0.l = LO(DMEM_CONTROL); @@ -134,17 +125,8 @@ ENTRY(__start) R1 = [p0]; R0 = ~ENDCPLB; R0 = R0 & R1; - - /* Anomaly 05000125 */ -#if ANOMALY_05000125 - CLI R2; - SSYNC; -#endif [p0] = R0; SSYNC; -#if ANOMALY_05000125 - STI R2; -#endif /* Initialise UART - when booting from u-boot, the UART is not disabled * so if we dont initalize here, our serial console gets hosed */ diff --git a/arch/blackfin/mach-bf537/head.S b/arch/blackfin/mach-bf537/head.S index 6b019eaee0b..5bc89bbb89d 100644 --- a/arch/blackfin/mach-bf537/head.S +++ b/arch/blackfin/mach-bf537/head.S @@ -105,17 +105,8 @@ ENTRY(__start) R1 = [p0]; R0 = ~ENICPLB; R0 = R0 & R1; - - /* Anomaly 05000125 */ -#if ANOMALY_05000125 - CLI R2; - SSYNC; -#endif [p0] = R0; SSYNC; -#if ANOMALY_05000125 - STI R2; -#endif /* Turn off the dcache */ p0.l = LO(DMEM_CONTROL); @@ -123,48 +114,20 @@ ENTRY(__start) R1 = [p0]; R0 = ~ENDCPLB; R0 = R0 & R1; - - /* Anomaly 05000125 */ -#if ANOMALY_05000125 - CLI R2; - SSYNC; -#endif [p0] = R0; SSYNC; -#if ANOMALY_05000125 - STI R2; -#endif /* Initialise General-Purpose I/O Modules on BF537 */ - /* Rev 0.0 Anomaly 05000212 - PORTx_FER, - * PORT_MUX Registers Do Not accept "writes" correctly: - */ p0.h = hi(BFIN_PORT_MUX); p0.l = lo(BFIN_PORT_MUX); -#if ANOMALY_05000212 - R0.L = W[P0]; /* Read */ - SSYNC; -#endif R0 = (PGDE_UART | PFTE_UART)(Z); -#if ANOMALY_05000212 - W[P0] = R0.L; /* Write */ - SSYNC; -#endif W[P0] = R0.L; /* Enable both UARTS */ SSYNC; + /* Enable peripheral function of PORTF for UART0 and UART1 */ p0.h = hi(PORTF_FER); p0.l = lo(PORTF_FER); -#if ANOMALY_05000212 - R0.L = W[P0]; /* Read */ - SSYNC; -#endif R0 = 0x000F(Z); -#if ANOMALY_05000212 - W[P0] = R0.L; /* Write */ - SSYNC; -#endif - /* Enable peripheral function of PORTF for UART0 and UART1 */ W[P0] = R0.L; SSYNC; diff --git a/arch/blackfin/mach-bf561/head.S b/arch/blackfin/mach-bf561/head.S index cf1a2dff01e..0a1443b6b46 100644 --- a/arch/blackfin/mach-bf561/head.S +++ b/arch/blackfin/mach-bf561/head.S @@ -105,16 +105,8 @@ ENTRY(__start) R1 = [p0]; R0 = ~ENICPLB; R0 = R0 & R1; - -#if ANOMALY_05000125 - CLI R2; - SSYNC; -#endif [p0] = R0; SSYNC; -#if ANOMALY_05000125 - STI R2; -#endif /* Turn off the dcache */ p0.l = LO(DMEM_CONTROL); @@ -122,17 +114,8 @@ ENTRY(__start) R1 = [p0]; R0 = ~ENDCPLB; R0 = R0 & R1; - - /* Anomaly 05000125 */ -#if ANOMALY_05000125 - CLI R2; - SSYNC; -#endif [p0] = R0; SSYNC; -#if ANOMALY_05000125 - STI R2; -#endif /* Initialise UART - when booting from u-boot, the UART is not disabled * so if we dont initalize here, our serial console gets hosed */ diff --git a/arch/blackfin/mach-common/Makefile b/arch/blackfin/mach-common/Makefile index 422bfee34ad..5e6b20e423d 100644 --- a/arch/blackfin/mach-common/Makefile +++ b/arch/blackfin/mach-common/Makefile @@ -3,7 +3,7 @@ # obj-y := \ - cache.o cacheinit.o entry.o \ + cache.o entry.o \ interrupt.o lock.o irqpanic.o arch_checks.o ints-priority.o obj-$(CONFIG_PM) += pm.o dpmc_modes.o diff --git a/arch/blackfin/mach-common/cacheinit.S b/arch/blackfin/mach-common/cacheinit.S deleted file mode 100644 index 22fada0c1cb..00000000000 --- a/arch/blackfin/mach-common/cacheinit.S +++ /dev/null @@ -1,77 +0,0 @@ -/* - * File: arch/blackfin/mach-common/cacheinit.S - * Based on: - * Author: LG Soft India - * - * Created: ? - * Description: cache initialization - * - * Modified: - * Copyright 2004-2006 Analog Devices Inc. - * - * Bugs: Enter bugs at http://blackfin.uclinux.org/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, see the file COPYING, or write - * to the Free Software Foundation, Inc., - * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA - */ - -/* This function sets up the data and instruction cache. The - * tables like icplb table, dcplb table and Page Descriptor table - * are defined in cplbtab.h. You can configure those tables for - * your suitable requirements - */ - -#include -#include - -.text - -#if ANOMALY_05000125 -#if defined(CONFIG_BFIN_ICACHE) -ENTRY(_bfin_write_IMEM_CONTROL) - - /* Enable Instruction Cache */ - P0.l = LO(IMEM_CONTROL); - P0.h = HI(IMEM_CONTROL); - - /* Anomaly 05000125 */ - CLI R1; - SSYNC; /* SSYNC required before writing to IMEM_CONTROL. */ - .align 8; - [P0] = R0; - SSYNC; - STI R1; - RTS; - -ENDPROC(_bfin_write_IMEM_CONTROL) -#endif - -#if defined(CONFIG_BFIN_DCACHE) -ENTRY(_bfin_write_DMEM_CONTROL) - P0.l = LO(DMEM_CONTROL); - P0.h = HI(DMEM_CONTROL); - - CLI R1; - SSYNC; /* SSYNC required before writing to DMEM_CONTROL. */ - .align 8; - [P0] = R0; - SSYNC; - STI R1; - RTS; - -ENDPROC(_bfin_write_DMEM_CONTROL) -#endif - -#endif diff --git a/include/asm-blackfin/mach-common/cdef_LPBlackfin.h b/include/asm-blackfin/mach-common/cdef_LPBlackfin.h index ede210eca4e..d39c396f850 100644 --- a/include/asm-blackfin/mach-common/cdef_LPBlackfin.h +++ b/include/asm-blackfin/mach-common/cdef_LPBlackfin.h @@ -39,11 +39,7 @@ #define bfin_read_SRAM_BASE_ADDRESS() bfin_read32(SRAM_BASE_ADDRESS) #define bfin_write_SRAM_BASE_ADDRESS(val) bfin_write32(SRAM_BASE_ADDRESS,val) #define bfin_read_DMEM_CONTROL() bfin_read32(DMEM_CONTROL) -#if ANOMALY_05000125 -extern void bfin_write_DMEM_CONTROL(unsigned int val); -#else #define bfin_write_DMEM_CONTROL(val) bfin_write32(DMEM_CONTROL,val) -#endif #define bfin_read_DCPLB_STATUS() bfin_read32(DCPLB_STATUS) #define bfin_write_DCPLB_STATUS(val) bfin_write32(DCPLB_STATUS,val) #define bfin_read_DCPLB_FAULT_ADDR() bfin_read32(DCPLB_FAULT_ADDR) @@ -129,11 +125,7 @@ extern void bfin_write_DMEM_CONTROL(unsigned int val); #define DTEST_DATA3 0xFFE0040C */ #define bfin_read_IMEM_CONTROL() bfin_read32(IMEM_CONTROL) -#if ANOMALY_05000125 -extern void bfin_write_IMEM_CONTROL(unsigned int val); -#else #define bfin_write_IMEM_CONTROL(val) bfin_write32(IMEM_CONTROL,val) -#endif #define bfin_read_ICPLB_STATUS() bfin_read32(ICPLB_STATUS) #define bfin_write_ICPLB_STATUS(val) bfin_write32(ICPLB_STATUS,val) #define bfin_read_ICPLB_FAULT_ADDR() bfin_read32(ICPLB_FAULT_ADDR) -- GitLab From 09e1f70e31ed6ca23dd42feb10aa104fc1b04c40 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Wed, 6 Aug 2008 17:15:27 +0800 Subject: [PATCH 048/750] Blackfin arch: unify the duplicated _real_start functions Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- arch/blackfin/mach-bf527/head.S | 70 --------------------------- arch/blackfin/mach-bf533/head.S | 70 --------------------------- arch/blackfin/mach-bf537/head.S | 70 --------------------------- arch/blackfin/mach-bf548/head.S | 73 ---------------------------- arch/blackfin/mach-bf561/head.S | 70 --------------------------- arch/blackfin/mach-common/Makefile | 2 +- arch/blackfin/mach-common/head.S | 76 ++++++++++++++++++++++++++++++ 7 files changed, 77 insertions(+), 354 deletions(-) create mode 100644 arch/blackfin/mach-common/head.S diff --git a/arch/blackfin/mach-bf527/head.S b/arch/blackfin/mach-bf527/head.S index a16a2657528..180d3c85a4c 100644 --- a/arch/blackfin/mach-bf527/head.S +++ b/arch/blackfin/mach-bf527/head.S @@ -226,76 +226,6 @@ ENTRY(__start) jump .LWAIT_HERE; ENDPROC(__start) -ENTRY(_real_start) - [ -- sp ] = reti; - p0.l = lo(WDOG_CTL); - p0.h = hi(WDOG_CTL); - r0 = 0xAD6(z); - w[p0] = r0; /* watchdog off for now */ - ssync; - - /* Code update for BSS size == 0 - * Zero out the bss region. - */ - - p1.l = ___bss_start; - p1.h = ___bss_start; - p2.l = ___bss_stop; - p2.h = ___bss_stop; - r0 = 0; - p2 -= p1; - lsetup (.L_clear_bss, .L_clear_bss) lc0 = p2; -.L_clear_bss: - B[p1++] = r0; - - /* In case there is a NULL pointer reference - * Zero out region before stext - */ - - p1.l = 0x0; - p1.h = 0x0; - r0.l = __stext; - r0.h = __stext; - r0 = r0 >> 1; - p2 = r0; - r0 = 0; - lsetup (.L_clear_zero, .L_clear_zero) lc0 = p2; -.L_clear_zero: - W[p1++] = r0; - - /* pass the uboot arguments to the global value command line */ - R0 = R7; - call _cmdline_init; - - p1.l = __rambase; - p1.h = __rambase; - r0.l = __sdata; - r0.h = __sdata; - [p1] = r0; - - p1.l = __ramstart; - p1.h = __ramstart; - p3.l = ___bss_stop; - p3.h = ___bss_stop; - - r1 = p3; - [p1] = r1; - - /* - * load the current thread pointer and stack - */ - r1.l = _init_thread_union; - r1.h = _init_thread_union; - - r2.l = 0x2000; - r2.h = 0x0000; - r1 = r1 + r2; - sp = r1; - usp = sp; - fp = sp; - jump.l _start_kernel; -ENDPROC(_real_start) - __FINIT .section .l1.text diff --git a/arch/blackfin/mach-bf533/head.S b/arch/blackfin/mach-bf533/head.S index fb49169c0e7..0ffbe7a205b 100644 --- a/arch/blackfin/mach-bf533/head.S +++ b/arch/blackfin/mach-bf533/head.S @@ -228,76 +228,6 @@ ENTRY(__start) jump .LWAIT_HERE; ENDPROC(__start) -ENTRY(_real_start) - [ -- sp ] = reti; - p0.l = lo(WDOG_CTL); - p0.h = hi(WDOG_CTL); - r0 = 0xAD6(z); - w[p0] = r0; /* watchdog off for now */ - ssync; - - /* Code update for BSS size == 0 - * Zero out the bss region. - */ - - p1.l = ___bss_start; - p1.h = ___bss_start; - p2.l = ___bss_stop; - p2.h = ___bss_stop; - r0 = 0; - p2 -= p1; - lsetup (.L_clear_bss, .L_clear_bss) lc0 = p2; -.L_clear_bss: - B[p1++] = r0; - - /* In case there is a NULL pointer reference - * Zero out region before stext - */ - - p1.l = 0x0; - p1.h = 0x0; - r0.l = __stext; - r0.h = __stext; - r0 = r0 >> 1; - p2 = r0; - r0 = 0; - lsetup (.L_clear_zero, .L_clear_zero) lc0 = p2; -.L_clear_zero: - W[p1++] = r0; - - /* pass the uboot arguments to the global value command line */ - R0 = R7; - call _cmdline_init; - - p1.l = __rambase; - p1.h = __rambase; - r0.l = __sdata; - r0.h = __sdata; - [p1] = r0; - - p1.l = __ramstart; - p1.h = __ramstart; - p3.l = ___bss_stop; - p3.h = ___bss_stop; - - r1 = p3; - [p1] = r1; - - /* - * load the current thread pointer and stack - */ - r1.l = _init_thread_union; - r1.h = _init_thread_union; - - r2.l = 0x2000; - r2.h = 0x0000; - r1 = r1 + r2; - sp = r1; - usp = sp; - fp = sp; - jump.l _start_kernel; -ENDPROC(_real_start) - __FINIT .section .l1.text diff --git a/arch/blackfin/mach-bf537/head.S b/arch/blackfin/mach-bf537/head.S index 5bc89bbb89d..c11f0fd8225 100644 --- a/arch/blackfin/mach-bf537/head.S +++ b/arch/blackfin/mach-bf537/head.S @@ -240,76 +240,6 @@ ENTRY(__start) jump .LWAIT_HERE; ENDPROC(__start) -ENTRY(_real_start) - [ -- sp ] = reti; - p0.l = lo(WDOG_CTL); - p0.h = hi(WDOG_CTL); - r0 = 0xAD6(z); - w[p0] = r0; /* watchdog off for now */ - ssync; - - /* Code update for BSS size == 0 - * Zero out the bss region. - */ - - p1.l = ___bss_start; - p1.h = ___bss_start; - p2.l = ___bss_stop; - p2.h = ___bss_stop; - r0 = 0; - p2 -= p1; - lsetup (.L_clear_bss, .L_clear_bss) lc0 = p2; -.L_clear_bss: - B[p1++] = r0; - - /* In case there is a NULL pointer reference - * Zero out region before stext - */ - - p1.l = 0x0; - p1.h = 0x0; - r0.l = __stext; - r0.h = __stext; - r0 = r0 >> 1; - p2 = r0; - r0 = 0; - lsetup (.L_clear_zero, .L_clear_zero) lc0 = p2; -.L_clear_zero: - W[p1++] = r0; - - /* pass the uboot arguments to the global value command line */ - R0 = R7; - call _cmdline_init; - - p1.l = __rambase; - p1.h = __rambase; - r0.l = __sdata; - r0.h = __sdata; - [p1] = r0; - - p1.l = __ramstart; - p1.h = __ramstart; - p3.l = ___bss_stop; - p3.h = ___bss_stop; - - r1 = p3; - [p1] = r1; - - /* - * load the current thread pointer and stack - */ - r1.l = _init_thread_union; - r1.h = _init_thread_union; - - r2.l = 0x2000; - r2.h = 0x0000; - r1 = r1 + r2; - sp = r1; - usp = sp; - fp = sp; - jump.l _start_kernel; -ENDPROC(_real_start) - __FINIT .section .l1.text diff --git a/arch/blackfin/mach-bf548/head.S b/arch/blackfin/mach-bf548/head.S index 06b9178cfcf..96fbdb790a9 100644 --- a/arch/blackfin/mach-bf548/head.S +++ b/arch/blackfin/mach-bf548/head.S @@ -212,79 +212,6 @@ ENTRY(__start) jump .LWAIT_HERE; ENDPROC(__start) -ENTRY(_real_start) - [ -- sp ] = reti; - p0.l = lo(WDOG_CTL); - p0.h = hi(WDOG_CTL); - r0 = 0xAD6(z); - w[p0] = r0; /* watchdog off for now */ - ssync; - - /* Code update for BSS size == 0 - * Zero out the bss region. - */ - - p1.l = ___bss_start; - p1.h = ___bss_start; - p2.l = ___bss_stop; - p2.h = ___bss_stop; - r0 = 0; - p2 -= p1; - lsetup (.L_clear_bss, .L_clear_bss ) lc0 = p2; -.L_clear_bss: - B[p1++] = r0; - - /* In case there is a NULL pointer reference - * Zero out region before stext - */ - - p1.l = 0x0; - p1.h = 0x0; - r0.l = __stext; - r0.h = __stext; - r0 = r0 >> 1; - p2 = r0; - r0 = 0; - lsetup (.L_clear_zero, .L_clear_zero ) lc0 = p2; -.L_clear_zero: - W[p1++] = r0; - - /* pass the uboot arguments to the global value command line */ - R0 = R7; - call _cmdline_init; - - p1.l = __rambase; - p1.h = __rambase; - r0.l = __sdata; - r0.h = __sdata; - [p1] = r0; - - p1.l = __ramstart; - p1.h = __ramstart; - p3.l = ___bss_stop; - p3.h = ___bss_stop; - - r1 = p3; - [p1] = r1; - - - /* - * load the current thread pointer and stack - */ - r1.l = _init_thread_union; - r1.h = _init_thread_union; - - r2.l = 0x2000; - r2.h = 0x0000; - r1 = r1 + r2; - sp = r1; - usp = sp; - fp = sp; - call _start_kernel; -.L_exit: - jump.s .L_exit; -ENDPROC(_real_start) - __FINIT .section .l1.text diff --git a/arch/blackfin/mach-bf561/head.S b/arch/blackfin/mach-bf561/head.S index 0a1443b6b46..553b2d149d7 100644 --- a/arch/blackfin/mach-bf561/head.S +++ b/arch/blackfin/mach-bf561/head.S @@ -217,76 +217,6 @@ ENTRY(__start) jump .LWAIT_HERE; ENDPROC(__start) -ENTRY(_real_start) - [ -- sp ] = reti; - p0.l = lo(WDOGA_CTL); - p0.h = hi(WDOGA_CTL); - r0 = 0xAD6(z); - w[p0] = r0; /* watchdog off for now */ - ssync; - - /* Code update for BSS size == 0 - * Zero out the bss region. - */ - - p1.l = ___bss_start; - p1.h = ___bss_start; - p2.l = ___bss_stop; - p2.h = ___bss_stop; - r0 = 0; - p2 -= p1; - lsetup (.L_clear_bss, .L_clear_bss) lc0 = p2; -.L_clear_bss: - B[p1++] = r0; - - /* In case there is a NULL pointer reference - * Zero out region before stext - */ - - p1.l = 0x0; - p1.h = 0x0; - r0.l = __stext; - r0.h = __stext; - r0 = r0 >> 1; - p2 = r0; - r0 = 0; - lsetup (.L_clear_zero, .L_clear_zero) lc0 = p2; -.L_clear_zero: - W[p1++] = r0; - - /* pass the uboot arguments to the global value command line */ - R0 = R7; - call _cmdline_init; - - p1.l = __rambase; - p1.h = __rambase; - r0.l = __sdata; - r0.h = __sdata; - [p1] = r0; - - p1.l = __ramstart; - p1.h = __ramstart; - p3.l = ___bss_stop; - p3.h = ___bss_stop; - - r1 = p3; - [p1] = r1; - - /* - * load the current thread pointer and stack - */ - r1.l = _init_thread_union; - r1.h = _init_thread_union; - - r2.l = 0x2000; - r2.h = 0x0000; - r1 = r1 + r2; - sp = r1; - usp = sp; - fp = sp; - jump.l _start_kernel; -ENDPROC(_real_start) - __FINIT .section .l1.text diff --git a/arch/blackfin/mach-common/Makefile b/arch/blackfin/mach-common/Makefile index 5e6b20e423d..862cd73c950 100644 --- a/arch/blackfin/mach-common/Makefile +++ b/arch/blackfin/mach-common/Makefile @@ -3,7 +3,7 @@ # obj-y := \ - cache.o entry.o \ + cache.o entry.o head.o \ interrupt.o lock.o irqpanic.o arch_checks.o ints-priority.o obj-$(CONFIG_PM) += pm.o dpmc_modes.o diff --git a/arch/blackfin/mach-common/head.S b/arch/blackfin/mach-common/head.S new file mode 100644 index 00000000000..8514da58755 --- /dev/null +++ b/arch/blackfin/mach-common/head.S @@ -0,0 +1,76 @@ +/* + * Common Blackfin startup code + * + * Copyright 2004-2008 Analog Devices Inc. + * + * Enter bugs at http://blackfin.uclinux.org/ + * + * Licensed under the GPL-2 or later. + */ + +#include +#include +#include +#include + +/* A little BF561 glue ... */ +#ifndef WDOG_CTL +# define WDOG_CTL WDOGA_CTL +#endif + +__INIT + +ENTRY(_real_start) + /* Enable nested interrupts */ + [--sp] = reti; + + /* watchdog off for now */ + p0.l = lo(WDOG_CTL); + p0.h = hi(WDOG_CTL); + r0 = 0xAD6(z); + w[p0] = r0; + ssync; + + /* Zero out the bss region + * Note: this will fail if bss is 0 bytes ... + */ + r0 = 0 (z); + r1.l = ___bss_start; + r1.h = ___bss_start; + r2.l = ___bss_stop; + r2.h = ___bss_stop; + r2 = r2 - r1; + r2 >>= 2; + p1 = r1; + p2 = r2; + lsetup (.L_clear_bss, .L_clear_bss) lc0 = p2; +.L_clear_bss: + [p1++] = r0; + + /* In case there is a NULL pointer reference, + * zero out region before stext + */ + p1 = r0; + r2.l = __stext; + r2.h = __stext; + r2 >>= 2; + p2 = r2; + lsetup (.L_clear_zero, .L_clear_zero) lc0 = p2; +.L_clear_zero: + [p1++] = r0; + + /* Pass the u-boot arguments to the global value command line */ + R0 = R7; + call _cmdline_init; + + /* Load the current thread pointer and stack */ + sp.l = _init_thread_union; + sp.h = _init_thread_union; + p1 = THREAD_SIZE (z); + sp = sp + p1; + usp = sp; + fp = sp; + jump.l _start_kernel; +ENDPROC(_real_start) + +__FINIT -- GitLab From 1375204611f417541e55ee09e248acdbbb94356d Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Wed, 6 Aug 2008 17:10:57 +0800 Subject: [PATCH 049/750] Blackfin arch: make sure the BSS and kernel load address are 4 byte aligned Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- arch/blackfin/kernel/vmlinux.lds.S | 1 + arch/blackfin/mach-common/arch_checks.c | 9 +++++++++ 2 files changed, 10 insertions(+) diff --git a/arch/blackfin/kernel/vmlinux.lds.S b/arch/blackfin/kernel/vmlinux.lds.S index 0896e38d610..d062597e621 100644 --- a/arch/blackfin/kernel/vmlinux.lds.S +++ b/arch/blackfin/kernel/vmlinux.lds.S @@ -83,6 +83,7 @@ SECTIONS #if !L1_DATA_B_LENGTH *(.l1.bss.B) #endif + . = ALIGN(4); ___bss_stop = .; } diff --git a/arch/blackfin/mach-common/arch_checks.c b/arch/blackfin/mach-common/arch_checks.c index f9160d83b91..5986758b275 100644 --- a/arch/blackfin/mach-common/arch_checks.c +++ b/arch/blackfin/mach-common/arch_checks.c @@ -27,6 +27,7 @@ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ +#include #include #include @@ -53,3 +54,11 @@ # endif #endif /* CONFIG_BFIN_KERNEL_CLOCK */ + +#if CONFIG_BOOT_LOAD < FIXED_CODE_END +# error "The kernel load address must be after the fixed code section" +#endif + +#if (CONFIG_BOOT_LOAD & 0x3) +# error "The kernel load address must be 4 byte aligned" +#endif -- GitLab From 7e64acabfdb530b1b7d3db2592d75d102827baf3 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Wed, 6 Aug 2008 17:17:10 +0800 Subject: [PATCH 050/750] Blackfin arch: move async memory programming into common setup_arch() as the banks dont really need to be setup fully as early as head.S Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- arch/blackfin/kernel/setup.c | 10 ++++++++ arch/blackfin/mach-bf527/head.S | 22 ----------------- arch/blackfin/mach-bf533/head.S | 22 ----------------- arch/blackfin/mach-bf537/head.S | 22 ----------------- arch/blackfin/mach-bf548/head.S | 42 --------------------------------- arch/blackfin/mach-bf561/head.S | 22 ----------------- 6 files changed, 10 insertions(+), 130 deletions(-) diff --git a/arch/blackfin/kernel/setup.c b/arch/blackfin/kernel/setup.c index 23e637eb78d..15967e7578c 100644 --- a/arch/blackfin/kernel/setup.c +++ b/arch/blackfin/kernel/setup.c @@ -738,6 +738,16 @@ void __init setup_arch(char **cmdline_p) memory_setup(); + /* Initialize Async memory banks */ + bfin_write_EBIU_AMBCTL0(AMBCTL0VAL); + bfin_write_EBIU_AMBCTL1(AMBCTL1VAL); + bfin_write_EBIU_AMGCTL(AMGCTLVAL); +#ifdef CONFIG_EBIU_MBSCTLVAL + bfin_write_EBIU_MBSCTL(CONFIG_EBIU_MBSCTLVAL); + bfin_write_EBIU_MODE(CONFIG_EBIU_MODEVAL); + bfin_write_EBIU_FCTL(CONFIG_EBIU_FCTLVAL); +#endif + cclk = get_cclk(); sclk = get_sclk(); diff --git a/arch/blackfin/mach-bf527/head.S b/arch/blackfin/mach-bf527/head.S index 180d3c85a4c..9173dcecd15 100644 --- a/arch/blackfin/mach-bf527/head.S +++ b/arch/blackfin/mach-bf527/head.S @@ -170,28 +170,6 @@ ENTRY(__start) call _start_dma_code; #endif - /* Code for initializing Async memory banks */ - - p2.h = hi(EBIU_AMBCTL1); - p2.l = lo(EBIU_AMBCTL1); - r0.h = hi(AMBCTL1VAL); - r0.l = lo(AMBCTL1VAL); - [p2] = r0; - ssync; - - p2.h = hi(EBIU_AMBCTL0); - p2.l = lo(EBIU_AMBCTL0); - r0.h = hi(AMBCTL0VAL); - r0.l = lo(AMBCTL0VAL); - [p2] = r0; - ssync; - - p2.h = hi(EBIU_AMGCTL); - p2.l = lo(EBIU_AMGCTL); - r0 = AMGCTLVAL; - w[p2] = r0; - ssync; - /* This section keeps the processor in supervisor mode * during kernel boot. Switches to user mode at end of boot. * See page 3-9 of Hardware Reference manual for documentation. diff --git a/arch/blackfin/mach-bf533/head.S b/arch/blackfin/mach-bf533/head.S index 0ffbe7a205b..7f0a7a0c6fd 100644 --- a/arch/blackfin/mach-bf533/head.S +++ b/arch/blackfin/mach-bf533/head.S @@ -172,28 +172,6 @@ ENTRY(__start) call _start_dma_code; #endif - /* Code for initializing Async memory banks */ - - p2.h = hi(EBIU_AMBCTL1); - p2.l = lo(EBIU_AMBCTL1); - r0.h = hi(AMBCTL1VAL); - r0.l = lo(AMBCTL1VAL); - [p2] = r0; - ssync; - - p2.h = hi(EBIU_AMBCTL0); - p2.l = lo(EBIU_AMBCTL0); - r0.h = hi(AMBCTL0VAL); - r0.l = lo(AMBCTL0VAL); - [p2] = r0; - ssync; - - p2.h = hi(EBIU_AMGCTL); - p2.l = lo(EBIU_AMGCTL); - r0 = AMGCTLVAL; - w[p2] = r0; - ssync; - /* This section keeps the processor in supervisor mode * during kernel boot. Switches to user mode at end of boot. * See page 3-9 of Hardware Reference manual for documentation. diff --git a/arch/blackfin/mach-bf537/head.S b/arch/blackfin/mach-bf537/head.S index c11f0fd8225..c062acb0483 100644 --- a/arch/blackfin/mach-bf537/head.S +++ b/arch/blackfin/mach-bf537/head.S @@ -184,28 +184,6 @@ ENTRY(__start) call _start_dma_code; #endif - /* Code for initializing Async memory banks */ - - p2.h = hi(EBIU_AMBCTL1); - p2.l = lo(EBIU_AMBCTL1); - r0.h = hi(AMBCTL1VAL); - r0.l = lo(AMBCTL1VAL); - [p2] = r0; - ssync; - - p2.h = hi(EBIU_AMBCTL0); - p2.l = lo(EBIU_AMBCTL0); - r0.h = hi(AMBCTL0VAL); - r0.l = lo(AMBCTL0VAL); - [p2] = r0; - ssync; - - p2.h = hi(EBIU_AMGCTL); - p2.l = lo(EBIU_AMGCTL); - r0 = AMGCTLVAL; - w[p2] = r0; - ssync; - /* This section keeps the processor in supervisor mode * during kernel boot. Switches to user mode at end of boot. * See page 3-9 of Hardware Reference manual for documentation. diff --git a/arch/blackfin/mach-bf548/head.S b/arch/blackfin/mach-bf548/head.S index 96fbdb790a9..832a8d7212a 100644 --- a/arch/blackfin/mach-bf548/head.S +++ b/arch/blackfin/mach-bf548/head.S @@ -133,48 +133,6 @@ ENTRY(__start) #ifdef CONFIG_BFIN_KERNEL_CLOCK call _start_dma_code; #endif - /* Code for initializing Async memory banks */ - - p2.h = hi(EBIU_AMBCTL1); - p2.l = lo(EBIU_AMBCTL1); - r0.h = hi(AMBCTL1VAL); - r0.l = lo(AMBCTL1VAL); - [p2] = r0; - ssync; - - p2.h = hi(EBIU_AMBCTL0); - p2.l = lo(EBIU_AMBCTL0); - r0.h = hi(AMBCTL0VAL); - r0.l = lo(AMBCTL0VAL); - [p2] = r0; - ssync; - - p2.h = hi(EBIU_AMGCTL); - p2.l = lo(EBIU_AMGCTL); - r0 = AMGCTLVAL; - w[p2] = r0; - ssync; - - p2.h = hi(EBIU_MBSCTL); - p2.l = lo(EBIU_MBSCTL); - r0.h = hi(CONFIG_EBIU_MBSCTLVAL); - r0.l = lo(CONFIG_EBIU_MBSCTLVAL); - [p2] = r0; - ssync; - - p2.h = hi(EBIU_MODE); - p2.l = lo(EBIU_MODE); - r0.h = hi(CONFIG_EBIU_MODEVAL); - r0.l = lo(CONFIG_EBIU_MODEVAL); - [p2] = r0; - ssync; - - p2.h = hi(EBIU_FCTL); - p2.l = lo(EBIU_FCTL); - r0.h = hi(CONFIG_EBIU_FCTLVAL); - r0.l = lo(CONFIG_EBIU_FCTLVAL); - [p2] = r0; - ssync; /* This section keeps the processor in supervisor mode * during kernel boot. Switches to user mode at end of boot. diff --git a/arch/blackfin/mach-bf561/head.S b/arch/blackfin/mach-bf561/head.S index 553b2d149d7..c541b312c25 100644 --- a/arch/blackfin/mach-bf561/head.S +++ b/arch/blackfin/mach-bf561/head.S @@ -161,28 +161,6 @@ ENTRY(__start) call _start_dma_code; #endif - /* Code for initializing Async memory banks */ - - p2.h = hi(EBIU_AMBCTL1); - p2.l = lo(EBIU_AMBCTL1); - r0.h = hi(AMBCTL1VAL); - r0.l = lo(AMBCTL1VAL); - [p2] = r0; - ssync; - - p2.h = hi(EBIU_AMBCTL0); - p2.l = lo(EBIU_AMBCTL0); - r0.h = hi(AMBCTL0VAL); - r0.l = lo(AMBCTL0VAL); - [p2] = r0; - ssync; - - p2.h = hi(EBIU_AMGCTL); - p2.l = lo(EBIU_AMGCTL); - r0 = AMGCTLVAL; - w[p2] = r0; - ssync; - /* This section keeps the processor in supervisor mode * during kernel boot. Switches to user mode at end of boot. * See page 3-9 of Hardware Reference manual for documentation. -- GitLab From 67618fd8748a5d83f6bdcd578c8e748c3f47c4d4 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Wed, 6 Aug 2008 17:18:31 +0800 Subject: [PATCH 051/750] Blackfin arch: add asm/thread_info.h for THREAD_SIZE define Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- arch/blackfin/mach-common/head.S | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/blackfin/mach-common/head.S b/arch/blackfin/mach-common/head.S index 8514da58755..6a989a031ed 100644 --- a/arch/blackfin/mach-common/head.S +++ b/arch/blackfin/mach-common/head.S @@ -11,6 +11,7 @@ #include #include #include +#include #include /* A little BF561 glue ... */ -- GitLab From 17e89bcfa12f71b840361da07fe6c2f9c48d0605 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Wed, 6 Aug 2008 17:23:50 +0800 Subject: [PATCH 052/750] Blackfin arch: unify the duplicated portions of __start and split mach-specific pieces into _mach_early_start where they will be easier to trim over time Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- arch/blackfin/mach-bf527/head.S | 132 +----------------------------- arch/blackfin/mach-bf533/head.S | 131 +---------------------------- arch/blackfin/mach-bf537/head.S | 132 +----------------------------- arch/blackfin/mach-bf548/head.S | 133 +----------------------------- arch/blackfin/mach-bf561/head.S | 136 ++----------------------------- arch/blackfin/mach-common/head.S | 131 ++++++++++++++++++++++++++++- 6 files changed, 146 insertions(+), 649 deletions(-) diff --git a/arch/blackfin/mach-bf527/head.S b/arch/blackfin/mach-bf527/head.S index 9173dcecd15..af20183d0d9 100644 --- a/arch/blackfin/mach-bf527/head.S +++ b/arch/blackfin/mach-bf527/head.S @@ -30,93 +30,16 @@ #include #include #include -#include - #ifdef CONFIG_BFIN_KERNEL_CLOCK #include #include #endif -.extern ___bss_stop -.extern ___bss_start .extern _bf53x_relocate_l1_mem -#define INITIAL_STACK 0xFFB01000 - __INIT -ENTRY(__start) - /* R0: argument of command line string, passed from uboot, save it */ - R7 = R0; - /* Enable Cycle Counter and Nesting Of Interrupts */ -#ifdef CONFIG_BFIN_SCRATCH_REG_CYCLES - R0 = SYSCFG_SNEN; -#else - R0 = SYSCFG_SNEN | SYSCFG_CCEN; -#endif - SYSCFG = R0; - R0 = 0; - - /* Clear Out All the data and pointer Registers */ - R1 = R0; - R2 = R0; - R3 = R0; - R4 = R0; - R5 = R0; - R6 = R0; - - P0 = R0; - P1 = R0; - P2 = R0; - P3 = R0; - P4 = R0; - P5 = R0; - - LC0 = r0; - LC1 = r0; - L0 = r0; - L1 = r0; - L2 = r0; - L3 = r0; - - /* Clear Out All the DAG Registers */ - B0 = r0; - B1 = r0; - B2 = r0; - B3 = r0; - - I0 = r0; - I1 = r0; - I2 = r0; - I3 = r0; - - M0 = r0; - M1 = r0; - M2 = r0; - M3 = r0; - - trace_buffer_init(p0,r0); - P0 = R1; - R0 = R1; - - /* Turn off the icache */ - p0.l = LO(IMEM_CONTROL); - p0.h = HI(IMEM_CONTROL); - R1 = [p0]; - R0 = ~ENICPLB; - R0 = R0 & R1; - [p0] = R0; - SSYNC; - - /* Turn off the dcache */ - p0.l = LO(DMEM_CONTROL); - p0.h = HI(DMEM_CONTROL); - R1 = [p0]; - R0 = ~ENDCPLB; - R0 = R0 & R1; - [p0] = R0; - SSYNC; - +ENTRY(_mach_early_start) #if defined(CONFIG_BF527) p0.h = hi(EMAC_SYSTAT); p0.l = lo(EMAC_SYSTAT); @@ -152,57 +75,8 @@ ENTRY(__start) w[p0] = r0.L; /* To enable UART clock */ ssync; - /* Initialize stack pointer */ - sp.l = lo(INITIAL_STACK); - sp.h = hi(INITIAL_STACK); - fp = sp; - usp = sp; - -#ifdef CONFIG_EARLY_PRINTK - SP += -12; - call _init_early_exception_vectors; - SP += 12; -#endif - - /* Put The Code for PLL Programming and SDRAM Programming in L1 ISRAM */ - call _bf53x_relocate_l1_mem; -#ifdef CONFIG_BFIN_KERNEL_CLOCK - call _start_dma_code; -#endif - - /* This section keeps the processor in supervisor mode - * during kernel boot. Switches to user mode at end of boot. - * See page 3-9 of Hardware Reference manual for documentation. - */ - - /* EVT15 = _real_start */ - - p0.l = lo(EVT15); - p0.h = hi(EVT15); - p1.l = _real_start; - p1.h = _real_start; - [p0] = p1; - csync; - - p0.l = lo(IMASK); - p0.h = hi(IMASK); - p1.l = IMASK_IVG15; - p1.h = 0x0; - [p0] = p1; - csync; - - raise 15; - p0.l = .LWAIT_HERE; - p0.h = .LWAIT_HERE; - reti = p0; -#if ANOMALY_05000281 - nop; nop; nop; -#endif - rti; - -.LWAIT_HERE: - jump .LWAIT_HERE; -ENDPROC(__start) + rts; +ENDPROC(_mach_early_start) __FINIT diff --git a/arch/blackfin/mach-bf533/head.S b/arch/blackfin/mach-bf533/head.S index 7f0a7a0c6fd..6603967367e 100644 --- a/arch/blackfin/mach-bf533/head.S +++ b/arch/blackfin/mach-bf533/head.S @@ -30,74 +30,16 @@ #include #include #include -#include #ifdef CONFIG_BFIN_KERNEL_CLOCK #include #include #endif -.extern ___bss_stop -.extern ___bss_start .extern _bf53x_relocate_l1_mem -#define INITIAL_STACK 0xFFB01000 - __INIT -ENTRY(__start) - /* R0: argument of command line string, passed from uboot, save it */ - R7 = R0; - /* Enable Cycle Counter and Nesting Of Interrupts */ -#ifdef CONFIG_BFIN_SCRATCH_REG_CYCLES - R0 = SYSCFG_SNEN; -#else - R0 = SYSCFG_SNEN | SYSCFG_CCEN; -#endif - SYSCFG = R0; - R0 = 0; - - /* Clear Out All the data and pointer Registers */ - R1 = R0; - R2 = R0; - R3 = R0; - R4 = R0; - R5 = R0; - R6 = R0; - - P0 = R0; - P1 = R0; - P2 = R0; - P3 = R0; - P4 = R0; - P5 = R0; - - LC0 = r0; - LC1 = r0; - L0 = r0; - L1 = r0; - L2 = r0; - L3 = r0; - - /* Clear Out All the DAG Registers */ - B0 = r0; - B1 = r0; - B2 = r0; - B3 = r0; - - I0 = r0; - I1 = r0; - I2 = r0; - I3 = r0; - - M0 = r0; - M1 = r0; - M2 = r0; - M3 = r0; - - trace_buffer_init(p0,r0); - P0 = R1; - R0 = R1; - +ENTRY(_mach_early_start) p0.h = hi(FIO_MASKA_C); p0.l = lo(FIO_MASKA_C); r0 = 0xFFFF(Z); @@ -110,24 +52,6 @@ ENTRY(__start) w[p0] = r0.L; /* Disable all interrupts */ ssync; - /* Turn off the icache */ - p0.l = LO(IMEM_CONTROL); - p0.h = HI(IMEM_CONTROL); - R1 = [p0]; - R0 = ~ENICPLB; - R0 = R0 & R1; - [p0] = R0; - SSYNC; - - /* Turn off the dcache */ - p0.l = LO(DMEM_CONTROL); - p0.h = HI(DMEM_CONTROL); - R1 = [p0]; - R0 = ~ENDCPLB; - R0 = R0 & R1; - [p0] = R0; - SSYNC; - /* Initialise UART - when booting from u-boot, the UART is not disabled * so if we dont initalize here, our serial console gets hosed */ p0.h = hi(BFIN_UART_LCR); @@ -154,57 +78,8 @@ ENTRY(__start) w[p0] = r0.L; /* To enable UART clock */ ssync; - /* Initialize stack pointer */ - sp.l = lo(INITIAL_STACK); - sp.h = hi(INITIAL_STACK); - fp = sp; - usp = sp; - -#ifdef CONFIG_EARLY_PRINTK - SP += -12; - call _init_early_exception_vectors; - SP += 12; -#endif - - /* Put The Code for PLL Programming and SDRAM Programming in L1 ISRAM */ - call _bf53x_relocate_l1_mem; -#ifdef CONFIG_BFIN_KERNEL_CLOCK - call _start_dma_code; -#endif - - /* This section keeps the processor in supervisor mode - * during kernel boot. Switches to user mode at end of boot. - * See page 3-9 of Hardware Reference manual for documentation. - */ - - /* EVT15 = _real_start */ - - p0.l = lo(EVT15); - p0.h = hi(EVT15); - p1.l = _real_start; - p1.h = _real_start; - [p0] = p1; - csync; - - p0.l = lo(IMASK); - p0.h = hi(IMASK); - p1.l = IMASK_IVG15; - p1.h = 0x0; - [p0] = p1; - csync; - - raise 15; - p0.l = .LWAIT_HERE; - p0.h = .LWAIT_HERE; - reti = p0; -#if ANOMALY_05000281 - nop; nop; nop; -#endif - rti; - -.LWAIT_HERE: - jump .LWAIT_HERE; -ENDPROC(__start) + rts; +ENDPROC(_mach_early_start) __FINIT diff --git a/arch/blackfin/mach-bf537/head.S b/arch/blackfin/mach-bf537/head.S index c062acb0483..6a02e472587 100644 --- a/arch/blackfin/mach-bf537/head.S +++ b/arch/blackfin/mach-bf537/head.S @@ -30,93 +30,16 @@ #include #include #include -#include - #ifdef CONFIG_BFIN_KERNEL_CLOCK #include #include #endif -.extern ___bss_stop -.extern ___bss_start .extern _bf53x_relocate_l1_mem -#define INITIAL_STACK 0xFFB01000 - __INIT -ENTRY(__start) - /* R0: argument of command line string, passed from uboot, save it */ - R7 = R0; - /* Enable Cycle Counter and Nesting Of Interrupts */ -#ifdef CONFIG_BFIN_SCRATCH_REG_CYCLES - R0 = SYSCFG_SNEN; -#else - R0 = SYSCFG_SNEN | SYSCFG_CCEN; -#endif - SYSCFG = R0; - R0 = 0; - - /* Clear Out All the data and pointer Registers */ - R1 = R0; - R2 = R0; - R3 = R0; - R4 = R0; - R5 = R0; - R6 = R0; - - P0 = R0; - P1 = R0; - P2 = R0; - P3 = R0; - P4 = R0; - P5 = R0; - - LC0 = r0; - LC1 = r0; - L0 = r0; - L1 = r0; - L2 = r0; - L3 = r0; - - /* Clear Out All the DAG Registers */ - B0 = r0; - B1 = r0; - B2 = r0; - B3 = r0; - - I0 = r0; - I1 = r0; - I2 = r0; - I3 = r0; - - M0 = r0; - M1 = r0; - M2 = r0; - M3 = r0; - - trace_buffer_init(p0,r0); - P0 = R1; - R0 = R1; - - /* Turn off the icache */ - p0.l = LO(IMEM_CONTROL); - p0.h = HI(IMEM_CONTROL); - R1 = [p0]; - R0 = ~ENICPLB; - R0 = R0 & R1; - [p0] = R0; - SSYNC; - - /* Turn off the dcache */ - p0.l = LO(DMEM_CONTROL); - p0.h = HI(DMEM_CONTROL); - R1 = [p0]; - R0 = ~ENDCPLB; - R0 = R0 & R1; - [p0] = R0; - SSYNC; - +ENTRY(_mach_early_start) /* Initialise General-Purpose I/O Modules on BF537 */ p0.h = hi(BFIN_PORT_MUX); p0.l = lo(BFIN_PORT_MUX); @@ -166,57 +89,8 @@ ENTRY(__start) w[p0] = r0.L; /* To enable UART clock */ ssync; - /* Initialize stack pointer */ - sp.l = lo(INITIAL_STACK); - sp.h = hi(INITIAL_STACK); - fp = sp; - usp = sp; - -#ifdef CONFIG_EARLY_PRINTK - SP += -12; - call _init_early_exception_vectors; - SP += 12; -#endif - - /* Put The Code for PLL Programming and SDRAM Programming in L1 ISRAM */ - call _bf53x_relocate_l1_mem; -#ifdef CONFIG_BFIN_KERNEL_CLOCK - call _start_dma_code; -#endif - - /* This section keeps the processor in supervisor mode - * during kernel boot. Switches to user mode at end of boot. - * See page 3-9 of Hardware Reference manual for documentation. - */ - - /* EVT15 = _real_start */ - - p0.l = lo(EVT15); - p0.h = hi(EVT15); - p1.l = _real_start; - p1.h = _real_start; - [p0] = p1; - csync; - - p0.l = lo(IMASK); - p0.h = hi(IMASK); - p1.l = IMASK_IVG15; - p1.h = 0x0; - [p0] = p1; - csync; - - raise 15; - p0.l = .LWAIT_HERE; - p0.h = .LWAIT_HERE; - reti = p0; -#if ANOMALY_05000281 - nop; nop; nop; -#endif - rti; - -.LWAIT_HERE: - jump .LWAIT_HERE; -ENDPROC(__start) + rts; +ENDPROC(_mach_early_start) __FINIT diff --git a/arch/blackfin/mach-bf548/head.S b/arch/blackfin/mach-bf548/head.S index 832a8d7212a..cf94e1e222b 100644 --- a/arch/blackfin/mach-bf548/head.S +++ b/arch/blackfin/mach-bf548/head.S @@ -30,145 +30,18 @@ #include #include #include -#include #ifdef CONFIG_BFIN_KERNEL_CLOCK #include #include #endif -.extern ___bss_stop -.extern ___bss_start .extern _bf53x_relocate_l1_mem -#define INITIAL_STACK 0xFFB01000 - __INIT -ENTRY(__start) - /* R0: argument of command line string, passed from uboot, save it */ - R7 = R0; - /* Enable Cycle Counter and Nesting Of Interrupts */ -#ifdef CONFIG_BFIN_SCRATCH_REG_CYCLES - R0 = SYSCFG_SNEN; -#else - R0 = SYSCFG_SNEN | SYSCFG_CCEN; -#endif - SYSCFG = R0; - R0 = 0; - - /* Clear Out All the data and pointer Registers*/ - R1 = R0; - R2 = R0; - R3 = R0; - R4 = R0; - R5 = R0; - R6 = R0; - - P0 = R0; - P1 = R0; - P2 = R0; - P3 = R0; - P4 = R0; - P5 = R0; - - LC0 = r0; - LC1 = r0; - L0 = r0; - L1 = r0; - L2 = r0; - L3 = r0; - - /* Clear Out All the DAG Registers*/ - B0 = r0; - B1 = r0; - B2 = r0; - B3 = r0; - - I0 = r0; - I1 = r0; - I2 = r0; - I3 = r0; - - M0 = r0; - M1 = r0; - M2 = r0; - M3 = r0; - - trace_buffer_init(p0,r0); - P0 = R1; - R0 = R1; - - /* Turn off the icache */ - p0.l = LO(IMEM_CONTROL); - p0.h = HI(IMEM_CONTROL); - R1 = [p0]; - R0 = ~ENICPLB; - R0 = R0 & R1; - [p0] = R0; - SSYNC; - - /* Turn off the dcache */ - p0.l = LO(DMEM_CONTROL); - p0.h = HI(DMEM_CONTROL); - R1 = [p0]; - R0 = ~ENDCPLB; - R0 = R0 & R1; - [p0] = R0; - SSYNC; - - /* Initialize stack pointer */ - SP.L = LO(INITIAL_STACK); - SP.H = HI(INITIAL_STACK); - FP = SP; - USP = SP; - -#ifdef CONFIG_EARLY_PRINTK - SP += -12; - call _init_early_exception_vectors; - SP += 12; -#endif - - /* Put The Code for PLL Programming and SDRAM Programming in L1 ISRAM */ - call _bf53x_relocate_l1_mem; -#ifdef CONFIG_BFIN_KERNEL_CLOCK - call _start_dma_code; -#endif - - /* This section keeps the processor in supervisor mode - * during kernel boot. Switches to user mode at end of boot. - * See page 3-9 of Hardware Reference manual for documentation. - */ - - /* EVT15 = _real_start */ - - p0.l = lo(EVT15); - p0.h = hi(EVT15); - p1.l = _real_start; - p1.h = _real_start; - [p0] = p1; - csync; - - p0.l = lo(IMASK); - p0.h = hi(IMASK); - p1.l = IMASK_IVG15; - p1.h = 0x0; - [p0] = p1; - csync; - - raise 15; - p0.l = .LWAIT_HERE; - p0.h = .LWAIT_HERE; - reti = p0; -#if ANOMALY_05000281 - nop; - nop; - nop; -#endif - rti; - -.LWAIT_HERE: - jump .LWAIT_HERE; -ENDPROC(__start) +ENTRY(_mach_early_start) + rts; +ENDPROC(_mach_early_start) __FINIT diff --git a/arch/blackfin/mach-bf561/head.S b/arch/blackfin/mach-bf561/head.S index c541b312c25..fe6f979947c 100644 --- a/arch/blackfin/mach-bf561/head.S +++ b/arch/blackfin/mach-bf561/head.S @@ -30,93 +30,16 @@ #include #include #include -#include - -#if CONFIG_BFIN_KERNEL_CLOCK +#ifdef CONFIG_BFIN_KERNEL_CLOCK #include #include #endif -.extern ___bss_stop -.extern ___bss_start .extern _bf53x_relocate_l1_mem -#define INITIAL_STACK 0xFFB01000 - __INIT -ENTRY(__start) - /* R0: argument of command line string, passed from uboot, save it */ - R7 = R0; - /* Enable Cycle Counter and Nesting Of Interrupts */ -#ifdef CONFIG_BFIN_SCRATCH_REG_CYCLES - R0 = SYSCFG_SNEN; -#else - R0 = SYSCFG_SNEN | SYSCFG_CCEN; -#endif - SYSCFG = R0; - R0 = 0; - - /* Clear Out All the data and pointer Registers */ - R1 = R0; - R2 = R0; - R3 = R0; - R4 = R0; - R5 = R0; - R6 = R0; - - P0 = R0; - P1 = R0; - P2 = R0; - P3 = R0; - P4 = R0; - P5 = R0; - - LC0 = r0; - LC1 = r0; - L0 = r0; - L1 = r0; - L2 = r0; - L3 = r0; - - /* Clear Out All the DAG Registers */ - B0 = r0; - B1 = r0; - B2 = r0; - B3 = r0; - - I0 = r0; - I1 = r0; - I2 = r0; - I3 = r0; - - M0 = r0; - M1 = r0; - M2 = r0; - M3 = r0; - - trace_buffer_init(p0,r0); - P0 = R1; - R0 = R1; - - /* Turn off the icache */ - p0.l = LO(IMEM_CONTROL); - p0.h = HI(IMEM_CONTROL); - R1 = [p0]; - R0 = ~ENICPLB; - R0 = R0 & R1; - [p0] = R0; - SSYNC; - - /* Turn off the dcache */ - p0.l = LO(DMEM_CONTROL); - p0.h = HI(DMEM_CONTROL); - R1 = [p0]; - R0 = ~ENDCPLB; - R0 = R0 & R1; - [p0] = R0; - SSYNC; - +ENTRY(_mach_early_start) /* Initialise UART - when booting from u-boot, the UART is not disabled * so if we dont initalize here, our serial console gets hosed */ p0.h = hi(BFIN_UART_LCR); @@ -143,62 +66,13 @@ ENTRY(__start) w[p0] = r0.L; /* To enable UART clock */ ssync; - /* Initialize stack pointer */ - sp.l = lo(INITIAL_STACK); - sp.h = hi(INITIAL_STACK); - fp = sp; - usp = sp; - -#ifdef CONFIG_EARLY_PRINTK - SP += -12; - call _init_early_exception_vectors; - SP += 12; -#endif - - /* Put The Code for PLL Programming and SDRAM Programming in L1 ISRAM */ - call _bf53x_relocate_l1_mem; -#if CONFIG_BFIN_KERNEL_CLOCK - call _start_dma_code; -#endif - - /* This section keeps the processor in supervisor mode - * during kernel boot. Switches to user mode at end of boot. - * See page 3-9 of Hardware Reference manual for documentation. - */ - - /* EVT15 = _real_start */ - - p0.l = lo(EVT15); - p0.h = hi(EVT15); - p1.l = _real_start; - p1.h = _real_start; - [p0] = p1; - csync; - - p0.l = lo(IMASK); - p0.h = hi(IMASK); - p1.l = IMASK_IVG15; - p1.h = 0x0; - [p0] = p1; - csync; - - raise 15; - p0.l = .LWAIT_HERE; - p0.h = .LWAIT_HERE; - reti = p0; -#if ANOMALY_05000281 - nop; nop; nop; -#endif - rti; - -.LWAIT_HERE: - jump .LWAIT_HERE; -ENDPROC(__start) + rts; +ENDPROC(_mach_early_start) __FINIT .section .l1.text -#if CONFIG_BFIN_KERNEL_CLOCK +#ifdef CONFIG_BFIN_KERNEL_CLOCK ENTRY(_start_dma_code) p0.h = hi(SICA_IWR0); p0.l = lo(SICA_IWR0); diff --git a/arch/blackfin/mach-common/head.S b/arch/blackfin/mach-common/head.S index 6a989a031ed..2c69ad49894 100644 --- a/arch/blackfin/mach-common/head.S +++ b/arch/blackfin/mach-common/head.S @@ -14,13 +14,140 @@ #include #include +__INIT + +#define INITIAL_STACK (L1_SCRATCH_START + L1_SCRATCH_LENGTH - 12) + +ENTRY(__start) + /* R0: argument of command line string, passed from uboot, save it */ + R7 = R0; + /* Enable Cycle Counter and Nesting Of Interrupts */ +#ifdef CONFIG_BFIN_SCRATCH_REG_CYCLES + R0 = SYSCFG_SNEN; +#else + R0 = SYSCFG_SNEN | SYSCFG_CCEN; +#endif + SYSCFG = R0; + R0 = 0; + + /* Clear Out All the data and pointer Registers */ + R1 = R0; + R2 = R0; + R3 = R0; + R4 = R0; + R5 = R0; + R6 = R0; + + P0 = R0; + P1 = R0; + P2 = R0; + P3 = R0; + P4 = R0; + P5 = R0; + + LC0 = r0; + LC1 = r0; + L0 = r0; + L1 = r0; + L2 = r0; + L3 = r0; + + /* Clear Out All the DAG Registers */ + B0 = r0; + B1 = r0; + B2 = r0; + B3 = r0; + + I0 = r0; + I1 = r0; + I2 = r0; + I3 = r0; + + M0 = r0; + M1 = r0; + M2 = r0; + M3 = r0; + + trace_buffer_init(p0,r0); + P0 = R1; + R0 = R1; + + /* Turn off the icache */ + p0.l = LO(IMEM_CONTROL); + p0.h = HI(IMEM_CONTROL); + R1 = [p0]; + R0 = ~ENICPLB; + R0 = R0 & R1; + [p0] = R0; + SSYNC; + + /* Turn off the dcache */ + p0.l = LO(DMEM_CONTROL); + p0.h = HI(DMEM_CONTROL); + R1 = [p0]; + R0 = ~ENDCPLB; + R0 = R0 & R1; + [p0] = R0; + SSYNC; + + /* Let each Blackfin family do its own thing */ + call _mach_early_start; + + /* Initialize stack pointer */ + sp.l = lo(INITIAL_STACK); + sp.h = hi(INITIAL_STACK); + fp = sp; + usp = sp; + +#ifdef CONFIG_EARLY_PRINTK + call _init_early_exception_vectors; +#endif + + /* Put The Code for PLL Programming and SDRAM Programming in L1 ISRAM */ + call _bf53x_relocate_l1_mem; +#ifdef CONFIG_BFIN_KERNEL_CLOCK + call _start_dma_code; +#endif + + /* This section keeps the processor in supervisor mode + * during kernel boot. Switches to user mode at end of boot. + * See page 3-9 of Hardware Reference manual for documentation. + */ + + /* EVT15 = _real_start */ + + p0.l = lo(EVT15); + p0.h = hi(EVT15); + p1.l = _real_start; + p1.h = _real_start; + [p0] = p1; + csync; + + p0.l = lo(IMASK); + p0.h = hi(IMASK); + p1.l = IMASK_IVG15; + p1.h = 0x0; + [p0] = p1; + csync; + + raise 15; + p0.l = .LWAIT_HERE; + p0.h = .LWAIT_HERE; + reti = p0; +#if ANOMALY_05000281 + nop; nop; nop; +#endif + rti; + +.LWAIT_HERE: + jump .LWAIT_HERE; +ENDPROC(__start) + /* A little BF561 glue ... */ #ifndef WDOG_CTL # define WDOG_CTL WDOGA_CTL #endif -__INIT - ENTRY(_real_start) /* Enable nested interrupts */ [--sp] = reti; -- GitLab From 07aa7be5708afb3d9afa68f6f853c98e51bc64b3 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Wed, 13 Aug 2008 16:16:11 +0800 Subject: [PATCH 053/750] Blackfin arch: convert L2 defines to be the same as the L1 defines Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- arch/blackfin/kernel/cplb-nompu/cplbinit.c | 6 +----- arch/blackfin/kernel/setup.c | 14 +++++++------- arch/blackfin/kernel/traps.c | 2 +- arch/blackfin/kernel/vmlinux.lds.S | 10 ++++------ arch/blackfin/mm/blackfin_sram.c | 12 ++++++------ include/asm-blackfin/mach-bf527/mem_map.h | 5 +++++ include/asm-blackfin/mach-bf533/mem_map.h | 5 +++++ include/asm-blackfin/mach-bf537/mem_map.h | 5 +++++ 8 files changed, 34 insertions(+), 25 deletions(-) diff --git a/arch/blackfin/kernel/cplb-nompu/cplbinit.c b/arch/blackfin/kernel/cplb-nompu/cplbinit.c index 224e7cc30bc..728f708d398 100644 --- a/arch/blackfin/kernel/cplb-nompu/cplbinit.c +++ b/arch/blackfin/kernel/cplb-nompu/cplbinit.c @@ -164,17 +164,13 @@ static struct cplb_desc cplb_data[] = { .name = "Asynchronous Memory Banks", }, { -#ifdef L2_START .start = L2_START, .end = L2_START + L2_LENGTH, .psize = SIZE_1M, .attr = SWITCH_T | I_CPLB | D_CPLB, .i_conf = L2_MEMORY, .d_conf = L2_MEMORY, - .valid = 1, -#else - .valid = 0, -#endif + .valid = (L2_LENGTH > 0), .name = "L2 Memory", }, { diff --git a/arch/blackfin/kernel/setup.c b/arch/blackfin/kernel/setup.c index 15967e7578c..936c06d820d 100644 --- a/arch/blackfin/kernel/setup.c +++ b/arch/blackfin/kernel/setup.c @@ -131,14 +131,14 @@ void __init bf53x_relocate_l1_mem(void) dma_memcpy(_sdata_b_l1, _l1_lma_start + l1_code_length + l1_data_a_length, l1_data_b_length); -#ifdef L2_LENGTH - l2_length = _ebss_l2 - _stext_l2; - if (l2_length > L2_LENGTH) - panic("L2 SRAM Overflow\n"); + if (L2_LENGTH != 0) { + l2_length = _ebss_l2 - _stext_l2; + if (l2_length > L2_LENGTH) + panic("L2 SRAM Overflow\n"); - /* Copy _stext_l2 to _edata_l2 to L2 SRAM */ - dma_memcpy(_stext_l2, _l2_lma_start, l2_length); -#endif + /* Copy _stext_l2 to _edata_l2 to L2 SRAM */ + dma_memcpy(_stext_l2, _l2_lma_start, l2_length); + } } /* add_memory_region to memmap */ diff --git a/arch/blackfin/kernel/traps.c b/arch/blackfin/kernel/traps.c index ad922ab9154..62a47d67d87 100644 --- a/arch/blackfin/kernel/traps.c +++ b/arch/blackfin/kernel/traps.c @@ -567,7 +567,7 @@ bool get_instruction(unsigned short *val, unsigned short *address) * we don't read something in the async space that can hang forever */ if ((addr >= FIXED_CODE_START && (addr + 2) <= physical_mem_end) || -#ifdef L2_START +#if L2_LENGTH != 0 (addr >= L2_START && (addr + 2) <= (L2_START + L2_LENGTH)) || #endif (addr >= BOOT_ROM_START && (addr + 2) <= (BOOT_ROM_START + BOOT_ROM_LENGTH)) || diff --git a/arch/blackfin/kernel/vmlinux.lds.S b/arch/blackfin/kernel/vmlinux.lds.S index d062597e621..7d12c6692a6 100644 --- a/arch/blackfin/kernel/vmlinux.lds.S +++ b/arch/blackfin/kernel/vmlinux.lds.S @@ -102,7 +102,7 @@ SECTIONS #if !L1_DATA_B_LENGTH *(.l1.data.B) #endif -#ifndef L2_LENGTH +#if !L2_LENGTH . = ALIGN(32); *(.data_l2.cacheline_aligned) *(.l2.data) @@ -212,20 +212,19 @@ SECTIONS __ebss_b_l1 = .; } -#ifdef L2_LENGTH __l2_lma_start = .; .text_data_l2 L2_START : AT(LOADADDR(.data_b_l1) + SIZEOF(.data_b_l1)) { . = ALIGN(4); __stext_l2 = .; - *(.l1.text) + *(.l2.text) . = ALIGN(4); __etext_l2 = .; . = ALIGN(4); __sdata_l2 = .; - *(.l1.data) + *(.l2.data) __edata_l2 = .; . = ALIGN(32); @@ -233,11 +232,10 @@ SECTIONS . = ALIGN(4); __sbss_l2 = .; - *(.l1.bss) + *(.l2.bss) . = ALIGN(4); __ebss_l2 = .; } -#endif /* Force trailing alignment of our init section so that when we * free our init memory, we don't leave behind a partial page. diff --git a/arch/blackfin/mm/blackfin_sram.c b/arch/blackfin/mm/blackfin_sram.c index 5af3c31c936..9d2be43ac3d 100644 --- a/arch/blackfin/mm/blackfin_sram.c +++ b/arch/blackfin/mm/blackfin_sram.c @@ -66,7 +66,7 @@ static struct sram_piece free_l1_data_B_sram_head, used_l1_data_B_sram_head; static struct sram_piece free_l1_inst_sram_head, used_l1_inst_sram_head; #endif -#ifdef L2_LENGTH +#if L2_LENGTH != 0 static struct sram_piece free_l2_sram_head, used_l2_sram_head; #endif @@ -175,7 +175,7 @@ static void __init l1_inst_sram_init(void) static void __init l2_sram_init(void) { -#ifdef L2_LENGTH +#if L2_LENGTH != 0 free_l2_sram_head.next = kmem_cache_alloc(sram_piece_cache, GFP_KERNEL); if (!free_l2_sram_head.next) { @@ -367,7 +367,7 @@ int sram_free(const void *addr) && addr < (void *)(L1_DATA_B_START + L1_DATA_B_LENGTH)) return l1_data_B_sram_free(addr); #endif -#ifdef L2_LENGTH +#if L2_LENGTH != 0 else if (addr >= (void *)L2_START && addr < (void *)(L2_START + L2_LENGTH)) return l2_sram_free(addr); @@ -604,7 +604,7 @@ int l1sram_free(const void *addr) void *l2_sram_alloc(size_t size) { -#ifdef L2_LENGTH +#if L2_LENGTH != 0 unsigned flags; void *addr; @@ -640,7 +640,7 @@ EXPORT_SYMBOL(l2_sram_zalloc); int l2_sram_free(const void *addr) { -#ifdef L2_LENGTH +#if L2_LENGTH != 0 unsigned flags; int ret; @@ -779,7 +779,7 @@ static int sram_proc_read(char *buf, char **start, off_t offset, int count, &free_l1_inst_sram_head, &used_l1_inst_sram_head)) goto not_done; #endif -#ifdef L2_LENGTH +#if L2_LENGTH != 0 if (_sram_proc_read(buf, &len, count, "L2", &free_l2_sram_head, &used_l2_sram_head)) goto not_done; diff --git a/include/asm-blackfin/mach-bf527/mem_map.h b/include/asm-blackfin/mach-bf527/mem_map.h index 193082deaa4..ef46dc991cd 100644 --- a/include/asm-blackfin/mach-bf527/mem_map.h +++ b/include/asm-blackfin/mach-bf527/mem_map.h @@ -89,6 +89,11 @@ #define BFIN_DSUPBANKS 0 #endif /*CONFIG_BFIN_DCACHE */ +/* Level 2 Memory - none */ + +#define L2_START 0 +#define L2_LENGTH 0 + /* Scratch Pad Memory */ #define L1_SCRATCH_START 0xFFB00000 diff --git a/include/asm-blackfin/mach-bf533/mem_map.h b/include/asm-blackfin/mach-bf533/mem_map.h index bd30b6f3be0..581fc6eea78 100644 --- a/include/asm-blackfin/mach-bf533/mem_map.h +++ b/include/asm-blackfin/mach-bf533/mem_map.h @@ -158,6 +158,11 @@ #endif +/* Level 2 Memory - none */ + +#define L2_START 0 +#define L2_LENGTH 0 + /* Scratch Pad Memory */ #define L1_SCRATCH_START 0xFFB00000 diff --git a/include/asm-blackfin/mach-bf537/mem_map.h b/include/asm-blackfin/mach-bf537/mem_map.h index 5c6726d6f3b..5078b669431 100644 --- a/include/asm-blackfin/mach-bf537/mem_map.h +++ b/include/asm-blackfin/mach-bf537/mem_map.h @@ -166,6 +166,11 @@ #endif +/* Level 2 Memory - none */ + +#define L2_START 0 +#define L2_LENGTH 0 + /* Scratch Pad Memory */ #define L1_SCRATCH_START 0xFFB00000 -- GitLab From 15b07536892284449ac5cd9488a8da1054b4295b Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Wed, 13 Aug 2008 16:19:36 +0800 Subject: [PATCH 054/750] Blackfin arch: delete unused cache functions Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- arch/blackfin/mach-common/cache.S | 115 ------------------------------ 1 file changed, 115 deletions(-) diff --git a/arch/blackfin/mach-common/cache.S b/arch/blackfin/mach-common/cache.S index 0521b158820..85f8c79b3c3 100644 --- a/arch/blackfin/mach-common/cache.S +++ b/arch/blackfin/mach-common/cache.S @@ -34,81 +34,6 @@ #include .text -.align 2 -ENTRY(_cache_invalidate) - - /* - * Icache or DcacheA or DcacheB Invalidation - * or any combination thereof - * R0 has bits - * CPLB_ENABLE_ICACHE_P,CPLB_ENABLE_DCACHE_P,CPLB_ENABLE_DCACHE2_P - * set as required - */ - [--SP] = R7; - - R7 = R0; - CC = BITTST(R7,CPLB_ENABLE_ICACHE_P); - IF !CC JUMP .Lno_icache; - [--SP] = RETS; - CALL _icache_invalidate; - RETS = [SP++]; -.Lno_icache: - CC = BITTST(R7,CPLB_ENABLE_DCACHE_P); - IF !CC JUMP .Lno_dcache_a; - R0 = 0; /* specifies bank A */ - [--SP] = RETS; - CALL _dcache_invalidate; - RETS = [SP++]; -.Lno_dcache_a: - CC = BITTST(R7,CPLB_ENABLE_DCACHE2_P); - IF !CC JUMP .Lno_dcache_b; - R0 = 0; - BITSET(R0, 23); /* specifies bank B */ - [--SP] = RETS; - CALL _dcache_invalidate; - RETS = [SP++]; -.Lno_dcache_b: - R7 = [SP++]; - RTS; -ENDPROC(_cache_invalidate) - -/* Invalidate the Entire Instruction cache by - * disabling IMC bit - */ -ENTRY(_icache_invalidate) -ENTRY(_invalidate_entire_icache) - [--SP] = ( R7:5); - - P0.L = LO(IMEM_CONTROL); - P0.H = HI(IMEM_CONTROL); - R7 = [P0]; - - /* Clear the IMC bit , All valid bits in the instruction - * cache are set to the invalid state - */ - BITCLR(R7,IMC_P); - CLI R6; - SSYNC; /* SSYNC required before invalidating cache. */ - .align 8; - [P0] = R7; - SSYNC; - STI R6; - - /* Configures the instruction cache agian */ - R6 = (IMC | ENICPLB); - R7 = R7 | R6; - - CLI R6; - SSYNC; /* SSYNC required before writing to IMEM_CONTROL. */ - .align 8; - [P0] = R7; - SSYNC; - STI R6; - - ( R7:5) = [SP++]; - RTS; -ENDPROC(_invalidate_entire_icache) -ENDPROC(_icache_invalidate) /* * blackfin_cache_flush_range(start, end) @@ -190,46 +115,6 @@ ENTRY(_blackfin_dcache_invalidate_range) RTS; ENDPROC(_blackfin_dcache_invalidate_range) -/* Invalidate the Entire Data cache by - * clearing DMC[1:0] bits - */ -ENTRY(_invalidate_entire_dcache) -ENTRY(_dcache_invalidate) - [--SP] = ( R7:6); - - P0.L = LO(DMEM_CONTROL); - P0.H = HI(DMEM_CONTROL); - R7 = [P0]; - - /* Clear the DMC[1:0] bits, All valid bits in the data - * cache are set to the invalid state - */ - BITCLR(R7,DMC0_P); - BITCLR(R7,DMC1_P); - CLI R6; - SSYNC; /* SSYNC required before writing to DMEM_CONTROL. */ - .align 8; - [P0] = R7; - SSYNC; - STI R6; - - /* Configures the data cache again */ - - R6 = DMEM_CNTR; - R7 = R7 | R6; - - CLI R6; - SSYNC; /* SSYNC required before writing to DMEM_CONTROL. */ - .align 8; - [P0] = R7; - SSYNC; - STI R6; - - ( R7:6) = [SP++]; - RTS; -ENDPROC(_dcache_invalidate) -ENDPROC(_invalidate_entire_dcache) - ENTRY(_blackfin_dcache_flush_range) R2 = -L1_CACHE_BYTES; R2 = R0 & R2; -- GitLab From 56f5f59052bb662a77d5ffd6cbe5861a2ef2407c Mon Sep 17 00:00:00 2001 From: Michael Hennerich Date: Wed, 6 Aug 2008 17:55:32 +0800 Subject: [PATCH 055/750] Blackfin arch: Fix Bug - System with EMAC driver enabled - Core not idling - Disable all bits in SIC_IWR unless we are going into a real (DPMC) power saving mode. Any Interrupt can wake the core form it's idle state. - Remove deep sleep mode as it is not going to be used anywhere: We support sleep, sleep deeper and hibernate. Signed-off-by: Michael Hennerich Signed-off-by: Bryan Wu --- arch/blackfin/mach-bf527/head.S | 7 --- arch/blackfin/mach-bf533/head.S | 7 --- arch/blackfin/mach-bf537/head.S | 7 --- arch/blackfin/mach-bf548/head.S | 7 --- arch/blackfin/mach-common/dpmc_modes.S | 56 ----------------------- arch/blackfin/mach-common/ints-priority.c | 8 ++-- arch/blackfin/mach-common/pm.c | 8 ++-- include/asm-blackfin/dpmc.h | 1 - 8 files changed, 8 insertions(+), 93 deletions(-) diff --git a/arch/blackfin/mach-bf527/head.S b/arch/blackfin/mach-bf527/head.S index af20183d0d9..2cc46f8fa9a 100644 --- a/arch/blackfin/mach-bf527/head.S +++ b/arch/blackfin/mach-bf527/head.S @@ -183,13 +183,6 @@ ENTRY(_start_dma_code) [P2] = R1; SSYNC; - p0.h = hi(SIC_IWR0); - p0.l = lo(SIC_IWR0); - r0.l = lo(IWR_ENABLE_ALL); - r0.h = hi(IWR_ENABLE_ALL); - [p0] = r0; - SSYNC; - RTS; ENDPROC(_start_dma_code) #endif /* CONFIG_BFIN_KERNEL_CLOCK */ diff --git a/arch/blackfin/mach-bf533/head.S b/arch/blackfin/mach-bf533/head.S index 6603967367e..184296bee3c 100644 --- a/arch/blackfin/mach-bf533/head.S +++ b/arch/blackfin/mach-bf533/head.S @@ -177,13 +177,6 @@ ENTRY(_start_dma_code) [P2] = R1; SSYNC; - p0.h = hi(SIC_IWR); - p0.l = lo(SIC_IWR); - r0.l = lo(IWR_ENABLE_ALL); - r0.h = hi(IWR_ENABLE_ALL); - [p0] = r0; - SSYNC; - RTS; ENDPROC(_start_dma_code) #endif /* CONFIG_BFIN_KERNEL_CLOCK */ diff --git a/arch/blackfin/mach-bf537/head.S b/arch/blackfin/mach-bf537/head.S index 6a02e472587..c02c8ce2d96 100644 --- a/arch/blackfin/mach-bf537/head.S +++ b/arch/blackfin/mach-bf537/head.S @@ -197,13 +197,6 @@ ENTRY(_start_dma_code) [P2] = R1; SSYNC; - p0.h = hi(SIC_IWR); - p0.l = lo(SIC_IWR); - r0.l = lo(IWR_ENABLE_ALL); - r0.h = hi(IWR_ENABLE_ALL); - [p0] = r0; - SSYNC; - RTS; ENDPROC(_start_dma_code) #endif /* CONFIG_BFIN_KERNEL_CLOCK */ diff --git a/arch/blackfin/mach-bf548/head.S b/arch/blackfin/mach-bf548/head.S index cf94e1e222b..0b18196df86 100644 --- a/arch/blackfin/mach-bf548/head.S +++ b/arch/blackfin/mach-bf548/head.S @@ -201,13 +201,6 @@ ENTRY(_start_dma_code) SSYNC; #endif - p0.h = hi(SIC_IWR0); - p0.l = lo(SIC_IWR0); - r0.l = lo(IWR_ENABLE_ALL); - r0.h = hi(IWR_ENABLE_ALL); - [p0] = r0; - SSYNC; - RTS; ENDPROC(_start_dma_code) #endif /* CONFIG_BFIN_KERNEL_CLOCK */ diff --git a/arch/blackfin/mach-common/dpmc_modes.S b/arch/blackfin/mach-common/dpmc_modes.S index 5e3f1d8a4fb..838b0b2ce9a 100644 --- a/arch/blackfin/mach-common/dpmc_modes.S +++ b/arch/blackfin/mach-common/dpmc_modes.S @@ -78,62 +78,6 @@ ENTRY(_hibernate_mode) jump .Lforever; ENDPROC(_hibernate_mode) -ENTRY(_deep_sleep) - [--SP] = ( R7:0, P5:0 ); - [--SP] = RETS; - - CLI R4; - - R0 = IWR_ENABLE(0); - R1 = IWR_DISABLE_ALL; - R2 = IWR_DISABLE_ALL; - - call _set_sic_iwr; - - call _set_dram_srfs; - - /* Clear all the interrupts,bits sticky */ - R0 = 0xFFFF (Z); - call _set_rtc_istat - - P0.H = hi(PLL_CTL); - P0.L = lo(PLL_CTL); - R0 = W[P0](z); - BITSET (R0, 5); - W[P0] = R0.L; - - call _test_pll_locked; - - SSYNC; - IDLE; - - call _unset_dram_srfs; - - call _test_pll_locked; - - R0 = IWR_ENABLE(0); - R1 = IWR_DISABLE_ALL; - R2 = IWR_DISABLE_ALL; - - call _set_sic_iwr; - - P0.H = hi(PLL_CTL); - P0.L = lo(PLL_CTL); - R0 = w[p0](z); - BITCLR (R0, 3); - BITCLR (R0, 5); - BITCLR (R0, 8); - w[p0] = R0; - IDLE; - call _test_pll_locked; - - STI R4; - - RETS = [SP++]; - ( R7:0, P5:0 ) = [SP++]; - RTS; -ENDPROC(_deep_sleep) - ENTRY(_sleep_deeper) [--SP] = ( R7:0, P5:0 ); [--SP] = RETS; diff --git a/arch/blackfin/mach-common/ints-priority.c b/arch/blackfin/mach-common/ints-priority.c index e713b9db867..4271ef3f201 100644 --- a/arch/blackfin/mach-common/ints-priority.c +++ b/arch/blackfin/mach-common/ints-priority.c @@ -1068,13 +1068,13 @@ int __init init_arch_irq(void) IMASK_IVG10 | IMASK_IVG9 | IMASK_IVG8 | IMASK_IVG7 | IMASK_IVGHW; #if defined(CONFIG_BF54x) || defined(CONFIG_BF52x) || defined(CONFIG_BF561) - bfin_write_SIC_IWR0(IWR_ENABLE_ALL); - bfin_write_SIC_IWR1(IWR_ENABLE_ALL); + bfin_write_SIC_IWR0(IWR_DISABLE_ALL); + bfin_write_SIC_IWR1(IWR_DISABLE_ALL); # ifdef CONFIG_BF54x - bfin_write_SIC_IWR2(IWR_ENABLE_ALL); + bfin_write_SIC_IWR2(IWR_DISABLE_ALL); # endif #else - bfin_write_SIC_IWR(IWR_ENABLE_ALL); + bfin_write_SIC_IWR(IWR_DISABLE_ALL); #endif return 0; diff --git a/arch/blackfin/mach-common/pm.c b/arch/blackfin/mach-common/pm.c index 143134b852e..a17ace3e0e4 100644 --- a/arch/blackfin/mach-common/pm.c +++ b/arch/blackfin/mach-common/pm.c @@ -83,13 +83,13 @@ void bfin_pm_suspend_standby_enter(void) bfin_pm_standby_restore(); #if defined(CONFIG_BF54x) || defined(CONFIG_BF52x) || defined(CONFIG_BF561) - bfin_write_SIC_IWR0(IWR_ENABLE_ALL); - bfin_write_SIC_IWR1(IWR_ENABLE_ALL); + bfin_write_SIC_IWR0(IWR_DISABLE_ALL); + bfin_write_SIC_IWR1(IWR_DISABLE_ALL); # ifdef CONFIG_BF54x - bfin_write_SIC_IWR2(IWR_ENABLE_ALL); + bfin_write_SIC_IWR2(IWR_DISABLE_ALL); # endif #else - bfin_write_SIC_IWR(IWR_ENABLE_ALL); + bfin_write_SIC_IWR(IWR_DISABLE_ALL); #endif local_irq_restore(flags); diff --git a/include/asm-blackfin/dpmc.h b/include/asm-blackfin/dpmc.h index de28e6e018b..96e8208f929 100644 --- a/include/asm-blackfin/dpmc.h +++ b/include/asm-blackfin/dpmc.h @@ -11,7 +11,6 @@ #ifndef __ASSEMBLY__ void sleep_mode(u32 sic_iwr0, u32 sic_iwr1, u32 sic_iwr2); -void deep_sleep(u32 sic_iwr0, u32 sic_iwr1, u32 sic_iwr2); void hibernate_mode(u32 sic_iwr0, u32 sic_iwr1, u32 sic_iwr2); void sleep_deeper(u32 sic_iwr0, u32 sic_iwr1, u32 sic_iwr2); void do_hibernate(int wakeup); -- GitLab From d3d0ac23a308f92fc5e5e2846ca40e7bffa5cec3 Mon Sep 17 00:00:00 2001 From: Robin Getz Date: Wed, 6 Aug 2008 17:49:27 +0800 Subject: [PATCH 056/750] Blackfin arch: Fix bug - when expanding the trace buffer, it does not print out the decoded instruction. as pointed out by Michael McTernan in the forums, when expanding the trace buffer, it does not print out the decoded instruction. Signed-off-by: Robin Getz Signed-off-by: Bryan Wu --- arch/blackfin/kernel/traps.c | 88 ++++++++++++++++++++++-------------- 1 file changed, 53 insertions(+), 35 deletions(-) diff --git a/arch/blackfin/kernel/traps.c b/arch/blackfin/kernel/traps.c index 62a47d67d87..9a9d5083acf 100644 --- a/arch/blackfin/kernel/traps.c +++ b/arch/blackfin/kernel/traps.c @@ -601,12 +601,55 @@ bool get_instruction(unsigned short *val, unsigned short *address) return false; } +/* + * decode the instruction if we are printing out the trace, as it + * makes things easier to follow, without running it through objdump + * These are the normal instructions which cause change of flow, which + * would be at the source of the trace buffer + */ +void decode_instruction(unsigned short *address) +{ + unsigned short opcode; + + if (get_instruction(&opcode, address)) { + if (opcode == 0x0010) + printk("RTS"); + else if (opcode == 0x0011) + printk("RTI"); + else if (opcode == 0x0012) + printk("RTX"); + else if (opcode >= 0x0050 && opcode <= 0x0057) + printk("JUMP (P%i)", opcode & 7); + else if (opcode >= 0x0060 && opcode <= 0x0067) + printk("CALL (P%i)", opcode & 7); + else if (opcode >= 0x0070 && opcode <= 0x0077) + printk("CALL (PC+P%i)", opcode & 7); + else if (opcode >= 0x0080 && opcode <= 0x0087) + printk("JUMP (PC+P%i)", opcode & 7); + else if ((opcode >= 0x1000 && opcode <= 0x13FF) || (opcode >= 0x1800 && opcode <= 0x1BFF)) + printk("IF !CC JUMP"); + else if ((opcode >= 0x1400 && opcode <= 0x17ff) || (opcode >= 0x1c00 && opcode <= 0x1fff)) + printk("IF CC JUMP"); + else if (opcode >= 0x2000 && opcode <= 0x2fff) + printk("JUMP.S"); + else if (opcode >= 0xe080 && opcode <= 0xe0ff) + printk("LSETUP"); + else if (opcode >= 0xe200 && opcode <= 0xe2ff) + printk("JUMP.L"); + else if (opcode >= 0xe300 && opcode <= 0xe3ff) + printk("CALL pcrel"); + else + printk("0x%04x", opcode); + } + +} + void dump_bfin_trace_buffer(void) { #ifdef CONFIG_DEBUG_BFIN_HWTRACE_ON int tflags, i = 0; char buf[150]; - unsigned short val = 0, *addr; + unsigned short *addr; #ifdef CONFIG_DEBUG_BFIN_HWTRACE_EXPAND int j, index; #endif @@ -615,6 +658,10 @@ void dump_bfin_trace_buffer(void) printk(KERN_NOTICE "Hardware Trace:\n"); +#ifdef CONFIG_DEBUG_BFIN_HWTRACE_EXPAND + printk(KERN_NOTICE "WARNING: Expanded trace turned on - can not trace exceptions\n"); +#endif + if (likely(bfin_read_TBUFSTAT() & TBUFCNT)) { for (; bfin_read_TBUFSTAT() & TBUFCNT; i++) { decode_address(buf, (unsigned long)bfin_read_TBUF()); @@ -622,45 +669,14 @@ void dump_bfin_trace_buffer(void) addr = (unsigned short *)bfin_read_TBUF(); decode_address(buf, (unsigned long)addr); printk(KERN_NOTICE " Source : %s ", buf); - if (get_instruction(&val, addr)) { - if (val == 0x0010) - printk("RTS"); - else if (val == 0x0011) - printk("RTI"); - else if (val == 0x0012) - printk("RTX"); - else if (val >= 0x0050 && val <= 0x0057) - printk("JUMP (P%i)", val & 7); - else if (val >= 0x0060 && val <= 0x0067) - printk("CALL (P%i)", val & 7); - else if (val >= 0x0070 && val <= 0x0077) - printk("CALL (PC+P%i)", val & 7); - else if (val >= 0x0080 && val <= 0x0087) - printk("JUMP (PC+P%i)", val & 7); - else if ((val >= 0x1000 && val <= 0x13FF) || - (val >= 0x1800 && val <= 0x1BFF)) - printk("IF !CC JUMP"); - else if ((val >= 0x1400 && val <= 0x17ff) || - (val >= 0x1c00 && val <= 0x1fff)) - printk("IF CC JUMP"); - else if (val >= 0x2000 && val <= 0x2fff) - printk("JUMP.S"); - else if (val >= 0xe080 && val <= 0xe0ff) - printk("LSETUP"); - else if (val >= 0xe200 && val <= 0xe2ff) - printk("JUMP.L"); - else if (val >= 0xe300 && val <= 0xe3ff) - printk("CALL pcrel"); - else - printk("0x%04x", val); - } + decode_instruction(addr); printk("\n"); } } #ifdef CONFIG_DEBUG_BFIN_HWTRACE_EXPAND if (trace_buff_offset) - index = trace_buff_offset/4 - 1; + index = trace_buff_offset / 4; else index = EXPAND_LEN; @@ -672,7 +688,9 @@ void dump_bfin_trace_buffer(void) if (index < 0 ) index = EXPAND_LEN; decode_address(buf, software_trace_buff[index]); - printk(KERN_NOTICE " Source : %s\n", buf); + printk(KERN_NOTICE " Source : %s ", buf); + decode_instruction((unsigned short *)software_trace_buff[index]); + printk("\n"); index -= 1; if (index < 0) index = EXPAND_LEN; -- GitLab From d211f052fa58a053639bc51501cb64421157d362 Mon Sep 17 00:00:00 2001 From: Hugh Dickins Date: Wed, 6 Aug 2008 18:21:18 +0100 Subject: [PATCH 057/750] [SCSI] sd: fix USB devices incorrectly reporting DIF support Some USB devices set the protect bit in the INQUIRY data which currently causes the DIF code in sd to assume (incorrectly) that they support READ_CAPACITY(16). Fix this (only for the time being) by making sure we only believe the protect bit in the inquiry data if the device claims conformance to SCSI-3 or above. Acked-by: Martin K. Petersen Signed-off-by: James Bottomley --- include/scsi/scsi_device.h | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/include/scsi/scsi_device.h b/include/scsi/scsi_device.h index 291d56a1916..80b2e93c293 100644 --- a/include/scsi/scsi_device.h +++ b/include/scsi/scsi_device.h @@ -6,6 +6,7 @@ #include #include #include +#include #include struct request_queue; @@ -426,7 +427,7 @@ static inline int scsi_device_enclosure(struct scsi_device *sdev) static inline int scsi_device_protection(struct scsi_device *sdev) { - return sdev->inquiry[5] & (1<<0); + return sdev->scsi_level > SCSI_2 && sdev->inquiry[5] & (1<<0); } #define MODULE_ALIAS_SCSI_DEVICE(type) \ -- GitLab From 8e4ae1017a555662d698ea4616dcfe71b17d3732 Mon Sep 17 00:00:00 2001 From: Carlos Corbacho Date: Wed, 6 Aug 2008 14:28:43 -0400 Subject: [PATCH 058/750] Input: i8042 - Add Dritek quirk for Acer TravelMate 4280 Reported-by: Mattias Jernberg Signed-off-by: Carlos Corbacho Signed-off-by: Dmitry Torokhov --- drivers/input/serio/i8042-x86ia64io.h | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/input/serio/i8042-x86ia64io.h b/drivers/input/serio/i8042-x86ia64io.h index fe732a574ec..3282b741e24 100644 --- a/drivers/input/serio/i8042-x86ia64io.h +++ b/drivers/input/serio/i8042-x86ia64io.h @@ -394,6 +394,13 @@ static struct dmi_system_id __initdata i8042_dmi_dritek_table[] = { DMI_MATCH(DMI_PRODUCT_NAME, "TravelMate 2490"), }, }, + { + .ident = "Acer TravelMate 4280", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Acer"), + DMI_MATCH(DMI_PRODUCT_NAME, "TravelMate 4280"), + }, + }, { } }; -- GitLab From 56ac36d722d0d27c03599d1245ac0ab59e474e5c Mon Sep 17 00:00:00 2001 From: Dan Williams Date: Thu, 7 Aug 2008 10:02:47 -0700 Subject: [PATCH 059/750] md: cancel check/repair requests when recovery is needed If a 'repair' is requested when an array is in a position to 'recover' raid1 will perform the repair while md believes a recovery is happening. Address this at both ends, i.e. cancel check/repair requests upon detecting a recover condition and do not call ->spare_active after completing a check/repair. Signed-off-by: Dan Williams --- drivers/md/md.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/md/md.c b/drivers/md/md.c index 25b893ec562..8cfadc5bd2b 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -6138,7 +6138,8 @@ void md_check_recovery(mddev_t *mddev) /* resync has finished, collect result */ md_unregister_thread(mddev->sync_thread); mddev->sync_thread = NULL; - if (!test_bit(MD_RECOVERY_INTR, &mddev->recovery)) { + if (!test_bit(MD_RECOVERY_INTR, &mddev->recovery) && + !test_bit(MD_RECOVERY_REQUESTED, &mddev->recovery)) { /* success...*/ /* activate any spares */ if (mddev->pers->spare_active(mddev)) @@ -6190,6 +6191,7 @@ void md_check_recovery(mddev_t *mddev) } else if ((spares = remove_and_add_spares(mddev))) { clear_bit(MD_RECOVERY_SYNC, &mddev->recovery); clear_bit(MD_RECOVERY_CHECK, &mddev->recovery); + clear_bit(MD_RECOVERY_REQUESTED, &mddev->recovery); set_bit(MD_RECOVERY_RECOVER, &mddev->recovery); } else if (mddev->recovery_cp < MaxSector) { set_bit(MD_RECOVERY_SYNC, &mddev->recovery); -- GitLab From 5402a7349d26875f69c184badf87b88541b1cf6c Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Tue, 5 Aug 2008 11:42:42 -0400 Subject: [PATCH 060/750] Input: evdev - split EVIOCGBIT handlig into a separate function Signed-off-by: Linus Torvalds Signed-off-by: Dmitry Torokhov --- drivers/input/evdev.c | 44 +++++++++++++++++++++++-------------------- 1 file changed, 24 insertions(+), 20 deletions(-) diff --git a/drivers/input/evdev.c b/drivers/input/evdev.c index 2d65411f676..ef8c2ed792c 100644 --- a/drivers/input/evdev.c +++ b/drivers/input/evdev.c @@ -647,6 +647,28 @@ static int str_to_user(const char *str, unsigned int maxlen, void __user *p) return copy_to_user(p, str, len) ? -EFAULT : len; } +static int handle_eviocgbit(struct input_dev *dev, unsigned int cmd, void __user *p, int compat_mode) +{ + unsigned long *bits; + int len; + + switch (_IOC_NR(cmd) & EV_MAX) { + + case 0: bits = dev->evbit; len = EV_MAX; break; + case EV_KEY: bits = dev->keybit; len = KEY_MAX; break; + case EV_REL: bits = dev->relbit; len = REL_MAX; break; + case EV_ABS: bits = dev->absbit; len = ABS_MAX; break; + case EV_MSC: bits = dev->mscbit; len = MSC_MAX; break; + case EV_LED: bits = dev->ledbit; len = LED_MAX; break; + case EV_SND: bits = dev->sndbit; len = SND_MAX; break; + case EV_FF: bits = dev->ffbit; len = FF_MAX; break; + case EV_SW: bits = dev->swbit; len = SW_MAX; break; + default: return -EINVAL; + } + return bits_to_user(bits, len, _IOC_SIZE(cmd), p, compat_mode); +} + + static long evdev_do_ioctl(struct file *file, unsigned int cmd, void __user *p, int compat_mode) { @@ -733,26 +755,8 @@ static long evdev_do_ioctl(struct file *file, unsigned int cmd, if (_IOC_DIR(cmd) == _IOC_READ) { - if ((_IOC_NR(cmd) & ~EV_MAX) == _IOC_NR(EVIOCGBIT(0, 0))) { - - unsigned long *bits; - int len; - - switch (_IOC_NR(cmd) & EV_MAX) { - - case 0: bits = dev->evbit; len = EV_MAX; break; - case EV_KEY: bits = dev->keybit; len = KEY_MAX; break; - case EV_REL: bits = dev->relbit; len = REL_MAX; break; - case EV_ABS: bits = dev->absbit; len = ABS_MAX; break; - case EV_MSC: bits = dev->mscbit; len = MSC_MAX; break; - case EV_LED: bits = dev->ledbit; len = LED_MAX; break; - case EV_SND: bits = dev->sndbit; len = SND_MAX; break; - case EV_FF: bits = dev->ffbit; len = FF_MAX; break; - case EV_SW: bits = dev->swbit; len = SW_MAX; break; - default: return -EINVAL; - } - return bits_to_user(bits, len, _IOC_SIZE(cmd), p, compat_mode); - } + if ((_IOC_NR(cmd) & ~EV_MAX) == _IOC_NR(EVIOCGBIT(0, 0))) + return handle_eviocgbit(dev, cmd, p, compat_mode); if (_IOC_NR(cmd) == _IOC_NR(EVIOCGKEY(0))) return bits_to_user(dev->key, KEY_MAX, _IOC_SIZE(cmd), -- GitLab From f2afa7711f8585ffc088ba538b9a510e0d5dca12 Mon Sep 17 00:00:00 2001 From: Dmitry Torokhov Date: Fri, 8 Aug 2008 11:46:53 -0400 Subject: [PATCH 061/750] Input: paper over a bug in Synaptics X driver Signed-off-by: Dmitry Torokhov --- drivers/input/evdev.c | 21 ++++++++++++++++++++- 1 file changed, 20 insertions(+), 1 deletion(-) diff --git a/drivers/input/evdev.c b/drivers/input/evdev.c index ef8c2ed792c..a92d8156755 100644 --- a/drivers/input/evdev.c +++ b/drivers/input/evdev.c @@ -647,8 +647,10 @@ static int str_to_user(const char *str, unsigned int maxlen, void __user *p) return copy_to_user(p, str, len) ? -EFAULT : len; } +#define OLD_KEY_MAX 0x1ff static int handle_eviocgbit(struct input_dev *dev, unsigned int cmd, void __user *p, int compat_mode) { + static unsigned long keymax_warn_time; unsigned long *bits; int len; @@ -665,9 +667,26 @@ static int handle_eviocgbit(struct input_dev *dev, unsigned int cmd, void __user case EV_SW: bits = dev->swbit; len = SW_MAX; break; default: return -EINVAL; } + + /* + * Work around bugs in userspace programs that like to do + * EVIOCGBIT(EV_KEY, KEY_MAX) and not realize that 'len' + * should be in bytes, not in bits. + */ + if ((_IOC_NR(cmd) & EV_MAX) == EV_KEY && _IOC_SIZE(cmd) == OLD_KEY_MAX) { + len = OLD_KEY_MAX; + if (printk_timed_ratelimit(&keymax_warn_time, 10 * 1000)) + printk(KERN_WARNING + "evdev.c(EVIOCGBIT): Suspicious buffer size %d, " + "limiting output to %d bytes. See " + "http://userweb.kernel.org/~dtor/eviocgbit-bug.html\n", + OLD_KEY_MAX, + BITS_TO_LONGS(OLD_KEY_MAX) * sizeof(long)); + } + return bits_to_user(bits, len, _IOC_SIZE(cmd), p, compat_mode); } - +#undef OLD_KEY_MAX static long evdev_do_ioctl(struct file *file, unsigned int cmd, void __user *p, int compat_mode) -- GitLab From f89bd95c5c946776f116ffeb997653d4193d6a35 Mon Sep 17 00:00:00 2001 From: Henrik Rydberg Date: Fri, 8 Aug 2008 14:59:30 -0400 Subject: [PATCH 062/750] Input: bcm5974 - add driver for Macbook Air and Pro Penryn touchpads This driver adds support for the multitouch trackpad on the new Apple Macbook Air and Macbook Pro Penryn laptops. It replaces the appletouch driver on those computers, and integrates well with the synaptics driver of the Xorg system. [dtor@mail.ru: various cleanups] Signed-off-by: Henrik Rydberg Signed-off-by: Dmitry Torokhov --- drivers/hid/usbhid/hid-quirks.c | 12 +- drivers/input/mouse/Kconfig | 23 ++ drivers/input/mouse/Makefile | 1 + drivers/input/mouse/bcm5974.c | 669 ++++++++++++++++++++++++++++++++ 4 files changed, 699 insertions(+), 6 deletions(-) create mode 100644 drivers/input/mouse/bcm5974.c diff --git a/drivers/hid/usbhid/hid-quirks.c b/drivers/hid/usbhid/hid-quirks.c index 61e78a4369b..b15f8824963 100644 --- a/drivers/hid/usbhid/hid-quirks.c +++ b/drivers/hid/usbhid/hid-quirks.c @@ -654,12 +654,12 @@ static const struct hid_blacklist { { USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_ALU_WIRELESS_ANSI, HID_QUIRK_APPLE_NUMLOCK_EMULATION | HID_QUIRK_APPLE_HAS_FN }, { USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_ALU_WIRELESS_ISO, HID_QUIRK_APPLE_NUMLOCK_EMULATION | HID_QUIRK_APPLE_HAS_FN | HID_QUIRK_APPLE_ISO_KEYBOARD }, { USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_ALU_WIRELESS_JIS, HID_QUIRK_APPLE_NUMLOCK_EMULATION | HID_QUIRK_APPLE_HAS_FN }, - { USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING_ANSI, HID_QUIRK_APPLE_HAS_FN }, - { USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING_ISO, HID_QUIRK_APPLE_HAS_FN | HID_QUIRK_APPLE_ISO_KEYBOARD }, - { USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING_JIS, HID_QUIRK_APPLE_HAS_FN }, - { USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING2_ANSI, HID_QUIRK_APPLE_HAS_FN }, - { USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING2_ISO, HID_QUIRK_APPLE_HAS_FN | HID_QUIRK_APPLE_ISO_KEYBOARD }, - { USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING2_JIS, HID_QUIRK_APPLE_HAS_FN }, + { USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING_ANSI, HID_QUIRK_APPLE_HAS_FN | HID_QUIRK_IGNORE_MOUSE }, + { USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING_ISO, HID_QUIRK_APPLE_HAS_FN | HID_QUIRK_APPLE_ISO_KEYBOARD | HID_QUIRK_IGNORE_MOUSE}, + { USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING_JIS, HID_QUIRK_APPLE_HAS_FN | HID_QUIRK_IGNORE_MOUSE}, + { USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING2_ANSI, HID_QUIRK_APPLE_HAS_FN | HID_QUIRK_IGNORE_MOUSE}, + { USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING2_ISO, HID_QUIRK_APPLE_HAS_FN | HID_QUIRK_APPLE_ISO_KEYBOARD | HID_QUIRK_IGNORE_MOUSE }, + { USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING2_JIS, HID_QUIRK_APPLE_HAS_FN | HID_QUIRK_IGNORE_MOUSE }, { USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_FOUNTAIN_TP_ONLY, HID_QUIRK_APPLE_NUMLOCK_EMULATION | HID_QUIRK_APPLE_HAS_FN | HID_QUIRK_IGNORE_MOUSE }, { USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_GEYSER1_TP_ONLY, HID_QUIRK_APPLE_NUMLOCK_EMULATION | HID_QUIRK_APPLE_HAS_FN | HID_QUIRK_IGNORE_MOUSE }, diff --git a/drivers/input/mouse/Kconfig b/drivers/input/mouse/Kconfig index 7bbea097cda..f996546fc44 100644 --- a/drivers/input/mouse/Kconfig +++ b/drivers/input/mouse/Kconfig @@ -130,6 +130,29 @@ config MOUSE_APPLETOUCH To compile this driver as a module, choose M here: the module will be called appletouch. +config MOUSE_BCM5974 + tristate "Apple USB BCM5974 Multitouch trackpad support" + depends on USB_ARCH_HAS_HCD + select USB + help + Say Y here if you have an Apple USB BCM5974 Multitouch + trackpad. + + The BCM5974 is the multitouch trackpad found in the Macbook + Air (JAN2008) and Macbook Pro Penryn (FEB2008) laptops. + + It is also found in the IPhone (2007) and Ipod Touch (2008). + + This driver provides multitouch functionality together with + the synaptics X11 driver. + + The interface is currently identical to the appletouch interface, + for further information, see + . + + To compile this driver as a module, choose M here: the + module will be called bcm5974. + config MOUSE_INPORT tristate "InPort/MS/ATIXL busmouse" depends on ISA diff --git a/drivers/input/mouse/Makefile b/drivers/input/mouse/Makefile index 9e6e3633082..d4d20251609 100644 --- a/drivers/input/mouse/Makefile +++ b/drivers/input/mouse/Makefile @@ -6,6 +6,7 @@ obj-$(CONFIG_MOUSE_AMIGA) += amimouse.o obj-$(CONFIG_MOUSE_APPLETOUCH) += appletouch.o +obj-$(CONFIG_MOUSE_BCM5974) += bcm5974.o obj-$(CONFIG_MOUSE_ATARI) += atarimouse.o obj-$(CONFIG_MOUSE_RISCPC) += rpcmouse.o obj-$(CONFIG_MOUSE_INPORT) += inport.o diff --git a/drivers/input/mouse/bcm5974.c b/drivers/input/mouse/bcm5974.c new file mode 100644 index 00000000000..6f852786c52 --- /dev/null +++ b/drivers/input/mouse/bcm5974.c @@ -0,0 +1,669 @@ +/* + * Apple USB BCM5974 (Macbook Air and Penryn Macbook Pro) multitouch driver + * + * Copyright (C) 2008 Henrik Rydberg (rydberg@euromail.se) + * + * The USB initialization and package decoding was made by + * Scott Shawcroft as part of the touchd user-space driver project: + * Copyright (C) 2008 Scott Shawcroft (scott.shawcroft@gmail.com) + * + * The BCM5974 driver is based on the appletouch driver: + * Copyright (C) 2001-2004 Greg Kroah-Hartman (greg@kroah.com) + * Copyright (C) 2005 Johannes Berg (johannes@sipsolutions.net) + * Copyright (C) 2005 Stelian Pop (stelian@popies.net) + * Copyright (C) 2005 Frank Arnold (frank@scirocco-5v-turbo.de) + * Copyright (C) 2005 Peter Osterlund (petero2@telia.com) + * Copyright (C) 2005 Michael Hanselmann (linux-kernel@hansmi.ch) + * Copyright (C) 2006 Nicolas Boichat (nicolas@boichat.ch) + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#define USB_VENDOR_ID_APPLE 0x05ac + +/* MacbookAir, aka wellspring */ +#define USB_DEVICE_ID_APPLE_WELLSPRING_ANSI 0x0223 +#define USB_DEVICE_ID_APPLE_WELLSPRING_ISO 0x0224 +#define USB_DEVICE_ID_APPLE_WELLSPRING_JIS 0x0225 +/* MacbookProPenryn, aka wellspring2 */ +#define USB_DEVICE_ID_APPLE_WELLSPRING2_ANSI 0x0230 +#define USB_DEVICE_ID_APPLE_WELLSPRING2_ISO 0x0231 +#define USB_DEVICE_ID_APPLE_WELLSPRING2_JIS 0x0232 + +#define BCM5974_DEVICE(prod) { \ + .match_flags = (USB_DEVICE_ID_MATCH_DEVICE | \ + USB_DEVICE_ID_MATCH_INT_CLASS | \ + USB_DEVICE_ID_MATCH_INT_PROTOCOL), \ + .idVendor = USB_VENDOR_ID_APPLE, \ + .idProduct = (prod), \ + .bInterfaceClass = USB_INTERFACE_CLASS_HID, \ + .bInterfaceProtocol = USB_INTERFACE_PROTOCOL_MOUSE \ +} + +/* table of devices that work with this driver */ +static const struct usb_device_id bcm5974_table [] = { + /* MacbookAir1.1 */ + BCM5974_DEVICE(USB_DEVICE_ID_APPLE_WELLSPRING_ANSI), + BCM5974_DEVICE(USB_DEVICE_ID_APPLE_WELLSPRING_ISO), + BCM5974_DEVICE(USB_DEVICE_ID_APPLE_WELLSPRING_JIS), + /* MacbookProPenryn */ + BCM5974_DEVICE(USB_DEVICE_ID_APPLE_WELLSPRING2_ANSI), + BCM5974_DEVICE(USB_DEVICE_ID_APPLE_WELLSPRING2_ISO), + BCM5974_DEVICE(USB_DEVICE_ID_APPLE_WELLSPRING2_JIS), + /* Terminating entry */ + {} +}; +MODULE_DEVICE_TABLE(usb, bcm5974_table); + +MODULE_AUTHOR("Henrik Rydberg"); +MODULE_DESCRIPTION("Apple USB BCM5974 multitouch driver"); +MODULE_LICENSE("GPL"); + +#define dprintk(level, format, a...)\ + { if (debug >= level) printk(KERN_DEBUG format, ##a); } + +static int debug = 1; +module_param(debug, int, 0644); +MODULE_PARM_DESC(debug, "Activate debugging output"); + +/* button data structure */ +struct bt_data { + u8 unknown1; /* constant */ + u8 button; /* left button */ + u8 rel_x; /* relative x coordinate */ + u8 rel_y; /* relative y coordinate */ +}; + +/* trackpad header structure */ +struct tp_header { + u8 unknown1[16]; /* constants, timers, etc */ + u8 fingers; /* number of fingers on trackpad */ + u8 unknown2[9]; /* constants, timers, etc */ +}; + +/* trackpad finger structure */ +struct tp_finger { + __le16 origin; /* left/right origin? */ + __le16 abs_x; /* absolute x coodinate */ + __le16 abs_y; /* absolute y coodinate */ + __le16 rel_x; /* relative x coodinate */ + __le16 rel_y; /* relative y coodinate */ + __le16 size_major; /* finger size, major axis? */ + __le16 size_minor; /* finger size, minor axis? */ + __le16 orientation; /* 16384 when point, else 15 bit angle */ + __le16 force_major; /* trackpad force, major axis? */ + __le16 force_minor; /* trackpad force, minor axis? */ + __le16 unused[3]; /* zeros */ + __le16 multi; /* one finger: varies, more fingers: constant */ +}; + +/* trackpad data structure, empirically at least ten fingers */ +struct tp_data { + struct tp_header header; + struct tp_finger finger[16]; +}; + +/* device-specific parameters */ +struct bcm5974_param { + int dim; /* logical dimension */ + int fuzz; /* logical noise value */ + int devmin; /* device minimum reading */ + int devmax; /* device maximum reading */ +}; + +/* device-specific configuration */ +struct bcm5974_config { + int ansi, iso, jis; /* the product id of this device */ + int bt_ep; /* the endpoint of the button interface */ + int bt_datalen; /* data length of the button interface */ + int tp_ep; /* the endpoint of the trackpad interface */ + int tp_datalen; /* data length of the trackpad interface */ + struct bcm5974_param p; /* finger pressure limits */ + struct bcm5974_param w; /* finger width limits */ + struct bcm5974_param x; /* horizontal limits */ + struct bcm5974_param y; /* vertical limits */ +}; + +/* logical device structure */ +struct bcm5974 { + char phys[64]; + struct usb_device *udev; /* usb device */ + struct input_dev *input; /* input dev */ + struct bcm5974_config cfg; /* device configuration */ + struct mutex pm_mutex; /* serialize access to open/suspend */ + int opened; /* 1: opened, 0: closed */ + struct urb *bt_urb; /* button usb request block */ + struct bt_data *bt_data; /* button transferred data */ + struct urb *tp_urb; /* trackpad usb request block */ + struct tp_data *tp_data; /* trackpad transferred data */ +}; + +/* logical dimensions */ +#define DIM_PRESSURE 256 /* maximum finger pressure */ +#define DIM_WIDTH 16 /* maximum finger width */ +#define DIM_X 1280 /* maximum trackpad x value */ +#define DIM_Y 800 /* maximum trackpad y value */ + +/* logical signal quality */ +#define SN_PRESSURE 45 /* pressure signal-to-noise ratio */ +#define SN_WIDTH 100 /* width signal-to-noise ratio */ +#define SN_COORD 250 /* coordinate signal-to-noise ratio */ + +/* device constants */ +static const struct bcm5974_config bcm5974_config_table[] = { + { + USB_DEVICE_ID_APPLE_WELLSPRING_ANSI, + USB_DEVICE_ID_APPLE_WELLSPRING_ISO, + USB_DEVICE_ID_APPLE_WELLSPRING_JIS, + 0x84, sizeof(struct bt_data), + 0x81, sizeof(struct tp_data), + { DIM_PRESSURE, DIM_PRESSURE / SN_PRESSURE, 0, 256 }, + { DIM_WIDTH, DIM_WIDTH / SN_WIDTH, 0, 2048 }, + { DIM_X, DIM_X / SN_COORD, -4824, 5342 }, + { DIM_Y, DIM_Y / SN_COORD, -172, 5820 } + }, + { + USB_DEVICE_ID_APPLE_WELLSPRING2_ANSI, + USB_DEVICE_ID_APPLE_WELLSPRING2_ISO, + USB_DEVICE_ID_APPLE_WELLSPRING2_JIS, + 0x84, sizeof(struct bt_data), + 0x81, sizeof(struct tp_data), + { DIM_PRESSURE, DIM_PRESSURE / SN_PRESSURE, 0, 256 }, + { DIM_WIDTH, DIM_WIDTH / SN_WIDTH, 0, 2048 }, + { DIM_X, DIM_X / SN_COORD, -4824, 4824 }, + { DIM_Y, DIM_Y / SN_COORD, -172, 4290 } + }, + {} +}; + +/* return the device-specific configuration by device */ +static const struct bcm5974_config *bcm5974_get_config(struct usb_device *udev) +{ + u16 id = le16_to_cpu(udev->descriptor.idProduct); + const struct bcm5974_config *cfg; + + for (cfg = bcm5974_config_table; cfg->ansi; ++cfg) + if (cfg->ansi == id || cfg->iso == id || cfg->jis == id) + return cfg; + + return bcm5974_config_table; +} + +/* convert 16-bit little endian to signed integer */ +static inline int raw2int(__le16 x) +{ + return (signed short)le16_to_cpu(x); +} + +/* scale device data to logical dimensions (asserts devmin < devmax) */ +static inline int int2scale(const struct bcm5974_param *p, int x) +{ + return x * p->dim / (p->devmax - p->devmin); +} + +/* all logical value ranges are [0,dim). */ +static inline int int2bound(const struct bcm5974_param *p, int x) +{ + int s = int2scale(p, x); + + return clamp_val(s, 0, p->dim - 1); +} + +/* setup which logical events to report */ +static void setup_events_to_report(struct input_dev *input_dev, + const struct bcm5974_config *cfg) +{ + __set_bit(EV_ABS, input_dev->evbit); + + input_set_abs_params(input_dev, ABS_PRESSURE, + 0, cfg->p.dim, cfg->p.fuzz, 0); + input_set_abs_params(input_dev, ABS_TOOL_WIDTH, + 0, cfg->w.dim, cfg->w.fuzz, 0); + input_set_abs_params(input_dev, ABS_X, + 0, cfg->x.dim, cfg->x.fuzz, 0); + input_set_abs_params(input_dev, ABS_Y, + 0, cfg->y.dim, cfg->y.fuzz, 0); + + __set_bit(EV_KEY, input_dev->evbit); + __set_bit(BTN_TOOL_FINGER, input_dev->keybit); + __set_bit(BTN_TOOL_DOUBLETAP, input_dev->keybit); + __set_bit(BTN_TOOL_TRIPLETAP, input_dev->keybit); + __set_bit(BTN_LEFT, input_dev->keybit); +} + +/* report button data as logical button state */ +static int report_bt_state(struct bcm5974 *dev, int size) +{ + if (size != sizeof(struct bt_data)) + return -EIO; + + input_report_key(dev->input, BTN_LEFT, dev->bt_data->button); + input_sync(dev->input); + + return 0; +} + +/* report trackpad data as logical trackpad state */ +static int report_tp_state(struct bcm5974 *dev, int size) +{ + const struct bcm5974_config *c = &dev->cfg; + const struct tp_finger *f = dev->tp_data->finger; + struct input_dev *input = dev->input; + const int fingers = (size - 26) / 28; + int p = 0, w, x, y, n = 0; + + if (size < 26 || (size - 26) % 28 != 0) + return -EIO; + + if (fingers) { + p = raw2int(f->force_major); + w = raw2int(f->size_major); + x = raw2int(f->abs_x); + y = raw2int(f->abs_y); + n = p > 0 ? fingers : 0; + + dprintk(9, + "bcm5974: p: %+05d w: %+05d x: %+05d y: %+05d n: %d\n", + p, w, x, y, n); + + input_report_abs(input, ABS_TOOL_WIDTH, int2bound(&c->w, w)); + input_report_abs(input, ABS_X, int2bound(&c->x, x - c->x.devmin)); + input_report_abs(input, ABS_Y, int2bound(&c->y, c->y.devmax - y)); + } + + input_report_abs(input, ABS_PRESSURE, int2bound(&c->p, p)); + + input_report_key(input, BTN_TOOL_FINGER, n == 1); + input_report_key(input, BTN_TOOL_DOUBLETAP, n == 2); + input_report_key(input, BTN_TOOL_TRIPLETAP, n > 2); + + input_sync(input); + + return 0; +} + +/* Wellspring initialization constants */ +#define BCM5974_WELLSPRING_MODE_READ_REQUEST_ID 1 +#define BCM5974_WELLSPRING_MODE_WRITE_REQUEST_ID 9 +#define BCM5974_WELLSPRING_MODE_REQUEST_VALUE 0x300 +#define BCM5974_WELLSPRING_MODE_REQUEST_INDEX 0 +#define BCM5974_WELLSPRING_MODE_VENDOR_VALUE 0x01 + +static int bcm5974_wellspring_mode(struct bcm5974 *dev) +{ + char *data = kmalloc(8, GFP_KERNEL); + int retval = 0, size; + + if (!data) { + err("bcm5974: out of memory"); + retval = -ENOMEM; + goto out; + } + + /* read configuration */ + size = usb_control_msg(dev->udev, usb_rcvctrlpipe(dev->udev, 0), + BCM5974_WELLSPRING_MODE_READ_REQUEST_ID, + USB_DIR_IN | USB_TYPE_CLASS | USB_RECIP_INTERFACE, + BCM5974_WELLSPRING_MODE_REQUEST_VALUE, + BCM5974_WELLSPRING_MODE_REQUEST_INDEX, data, 8, 5000); + + if (size != 8) { + err("bcm5974: could not read from device"); + retval = -EIO; + goto out; + } + + /* apply the mode switch */ + data[0] = BCM5974_WELLSPRING_MODE_VENDOR_VALUE; + + /* write configuration */ + size = usb_control_msg(dev->udev, usb_sndctrlpipe(dev->udev, 0), + BCM5974_WELLSPRING_MODE_WRITE_REQUEST_ID, + USB_DIR_OUT | USB_TYPE_CLASS | USB_RECIP_INTERFACE, + BCM5974_WELLSPRING_MODE_REQUEST_VALUE, + BCM5974_WELLSPRING_MODE_REQUEST_INDEX, data, 8, 5000); + + if (size != 8) { + err("bcm5974: could not write to device"); + retval = -EIO; + goto out; + } + + dprintk(2, "bcm5974: switched to wellspring mode.\n"); + + out: + kfree(data); + return retval; +} + +static void bcm5974_irq_button(struct urb *urb) +{ + struct bcm5974 *dev = urb->context; + int error; + + switch (urb->status) { + case 0: + break; + case -EOVERFLOW: + case -ECONNRESET: + case -ENOENT: + case -ESHUTDOWN: + dbg("bcm5974: button urb shutting down: %d", urb->status); + return; + default: + dbg("bcm5974: button urb status: %d", urb->status); + goto exit; + } + + if (report_bt_state(dev, dev->bt_urb->actual_length)) + dprintk(1, "bcm5974: bad button package, length: %d\n", + dev->bt_urb->actual_length); + +exit: + error = usb_submit_urb(dev->bt_urb, GFP_ATOMIC); + if (error) + err("bcm5974: button urb failed: %d", error); +} + +static void bcm5974_irq_trackpad(struct urb *urb) +{ + struct bcm5974 *dev = urb->context; + int error; + + switch (urb->status) { + case 0: + break; + case -EOVERFLOW: + case -ECONNRESET: + case -ENOENT: + case -ESHUTDOWN: + dbg("bcm5974: trackpad urb shutting down: %d", urb->status); + return; + default: + dbg("bcm5974: trackpad urb status: %d", urb->status); + goto exit; + } + + /* control response ignored */ + if (dev->tp_urb->actual_length == 2) + goto exit; + + if (report_tp_state(dev, dev->tp_urb->actual_length)) + dprintk(1, "bcm5974: bad trackpad package, length: %d\n", + dev->tp_urb->actual_length); + +exit: + error = usb_submit_urb(dev->tp_urb, GFP_ATOMIC); + if (error) + err("bcm5974: trackpad urb failed: %d", error); +} + +/* + * The Wellspring trackpad, like many recent Apple trackpads, share + * the usb device with the keyboard. Since keyboards are usually + * handled by the HID system, the device ends up being handled by two + * modules. Setting up the device therefore becomes slightly + * complicated. To enable multitouch features, a mode switch is + * required, which is usually applied via the control interface of the + * device. It can be argued where this switch should take place. In + * some drivers, like appletouch, the switch is made during + * probe. However, the hid module may also alter the state of the + * device, resulting in trackpad malfunction under certain + * circumstances. To get around this problem, there is at least one + * example that utilizes the USB_QUIRK_RESET_RESUME quirk in order to + * recieve a reset_resume request rather than the normal resume. + * Since the implementation of reset_resume is equal to mode switch + * plus start_traffic, it seems easier to always do the switch when + * starting traffic on the device. + */ +static int bcm5974_start_traffic(struct bcm5974 *dev) +{ + if (bcm5974_wellspring_mode(dev)) { + dprintk(1, "bcm5974: mode switch failed\n"); + goto error; + } + + if (usb_submit_urb(dev->bt_urb, GFP_KERNEL)) + goto error; + + if (usb_submit_urb(dev->tp_urb, GFP_KERNEL)) + goto err_kill_bt; + + return 0; + +err_kill_bt: + usb_kill_urb(dev->bt_urb); +error: + return -EIO; +} + +static void bcm5974_pause_traffic(struct bcm5974 *dev) +{ + usb_kill_urb(dev->tp_urb); + usb_kill_urb(dev->bt_urb); +} + +/* + * The code below implements open/close and manual suspend/resume. + * All functions may be called in random order. + * + * Opening a suspended device fails with EACCES - permission denied. + * + * Failing a resume leaves the device resumed but closed. + */ +static int bcm5974_open(struct input_dev *input) +{ + struct bcm5974 *dev = input_get_drvdata(input); + int error; + + mutex_lock(&dev->pm_mutex); + + error = bcm5974_start_traffic(dev); + if (!error) + dev->opened = 1; + + mutex_unlock(&dev->pm_mutex); + + return error; +} + +static void bcm5974_close(struct input_dev *input) +{ + struct bcm5974 *dev = input_get_drvdata(input); + + mutex_lock(&dev->pm_mutex); + + bcm5974_pause_traffic(dev); + dev->opened = 0; + + mutex_unlock(&dev->pm_mutex); +} + +static int bcm5974_suspend(struct usb_interface *iface, pm_message_t message) +{ + struct bcm5974 *dev = usb_get_intfdata(iface); + + mutex_lock(&dev->pm_mutex); + + if (dev->opened) + bcm5974_pause_traffic(dev); + + mutex_unlock(&dev->pm_mutex); + + return 0; +} + +static int bcm5974_resume(struct usb_interface *iface) +{ + struct bcm5974 *dev = usb_get_intfdata(iface); + int error = 0; + + mutex_lock(&dev->pm_mutex); + + if (dev->opened) + error = bcm5974_start_traffic(dev); + + mutex_unlock(&dev->pm_mutex); + + return error; +} + +static int bcm5974_probe(struct usb_interface *iface, + const struct usb_device_id *id) +{ + struct usb_device *udev = interface_to_usbdev(iface); + const struct bcm5974_config *cfg; + struct bcm5974 *dev; + struct input_dev *input_dev; + int error = -ENOMEM; + + /* find the product index */ + cfg = bcm5974_get_config(udev); + + /* allocate memory for our device state and initialize it */ + dev = kzalloc(sizeof(struct bcm5974), GFP_KERNEL); + input_dev = input_allocate_device(); + if (!dev || !input_dev) { + err("bcm5974: out of memory"); + goto err_free_devs; + } + + dev->udev = udev; + dev->input = input_dev; + dev->cfg = *cfg; + mutex_init(&dev->pm_mutex); + + /* setup urbs */ + dev->bt_urb = usb_alloc_urb(0, GFP_KERNEL); + if (!dev->bt_urb) + goto err_free_devs; + + dev->tp_urb = usb_alloc_urb(0, GFP_KERNEL); + if (!dev->tp_urb) + goto err_free_bt_urb; + + dev->bt_data = usb_buffer_alloc(dev->udev, + dev->cfg.bt_datalen, GFP_KERNEL, + &dev->bt_urb->transfer_dma); + if (!dev->bt_data) + goto err_free_urb; + + dev->tp_data = usb_buffer_alloc(dev->udev, + dev->cfg.tp_datalen, GFP_KERNEL, + &dev->tp_urb->transfer_dma); + if (!dev->tp_data) + goto err_free_bt_buffer; + + usb_fill_int_urb(dev->bt_urb, udev, + usb_rcvintpipe(udev, cfg->bt_ep), + dev->bt_data, dev->cfg.bt_datalen, + bcm5974_irq_button, dev, 1); + + usb_fill_int_urb(dev->tp_urb, udev, + usb_rcvintpipe(udev, cfg->tp_ep), + dev->tp_data, dev->cfg.tp_datalen, + bcm5974_irq_trackpad, dev, 1); + + /* create bcm5974 device */ + usb_make_path(udev, dev->phys, sizeof(dev->phys)); + strlcat(dev->phys, "/input0", sizeof(dev->phys)); + + input_dev->name = "bcm5974"; + input_dev->phys = dev->phys; + usb_to_input_id(dev->udev, &input_dev->id); + input_dev->dev.parent = &iface->dev; + + input_set_drvdata(input_dev, dev); + + input_dev->open = bcm5974_open; + input_dev->close = bcm5974_close; + + setup_events_to_report(input_dev, cfg); + + error = input_register_device(dev->input); + if (error) + goto err_free_buffer; + + /* save our data pointer in this interface device */ + usb_set_intfdata(iface, dev); + + return 0; + +err_free_buffer: + usb_buffer_free(dev->udev, dev->cfg.tp_datalen, + dev->tp_data, dev->tp_urb->transfer_dma); +err_free_bt_buffer: + usb_buffer_free(dev->udev, dev->cfg.bt_datalen, + dev->bt_data, dev->bt_urb->transfer_dma); +err_free_urb: + usb_free_urb(dev->tp_urb); +err_free_bt_urb: + usb_free_urb(dev->bt_urb); +err_free_devs: + usb_set_intfdata(iface, NULL); + input_free_device(input_dev); + kfree(dev); + return error; +} + +static void bcm5974_disconnect(struct usb_interface *iface) +{ + struct bcm5974 *dev = usb_get_intfdata(iface); + + usb_set_intfdata(iface, NULL); + + input_unregister_device(dev->input); + usb_buffer_free(dev->udev, dev->cfg.tp_datalen, + dev->tp_data, dev->tp_urb->transfer_dma); + usb_buffer_free(dev->udev, dev->cfg.bt_datalen, + dev->bt_data, dev->bt_urb->transfer_dma); + usb_free_urb(dev->tp_urb); + usb_free_urb(dev->bt_urb); + kfree(dev); +} + +static struct usb_driver bcm5974_driver = { + .name = "bcm5974", + .probe = bcm5974_probe, + .disconnect = bcm5974_disconnect, + .suspend = bcm5974_suspend, + .resume = bcm5974_resume, + .reset_resume = bcm5974_resume, + .id_table = bcm5974_table, +}; + +static int __init bcm5974_init(void) +{ + return usb_register(&bcm5974_driver); +} + +static void __exit bcm5974_exit(void) +{ + usb_deregister(&bcm5974_driver); +} + +module_init(bcm5974_init); +module_exit(bcm5974_exit); + -- GitLab From 88da765f4d5f59f67a7a51c8f5d608a836b32133 Mon Sep 17 00:00:00 2001 From: Dmitry Torokhov Date: Fri, 8 Aug 2008 14:59:32 -0400 Subject: [PATCH 063/750] Input: bcm5974 - implement autosuspend support Signed-off-by: Dmitry Torokhov --- drivers/input/mouse/bcm5974.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/drivers/input/mouse/bcm5974.c b/drivers/input/mouse/bcm5974.c index 6f852786c52..2ec921bf3c6 100644 --- a/drivers/input/mouse/bcm5974.c +++ b/drivers/input/mouse/bcm5974.c @@ -150,6 +150,7 @@ struct bcm5974_config { struct bcm5974 { char phys[64]; struct usb_device *udev; /* usb device */ + struct usb_interface *intf; /* our interface */ struct input_dev *input; /* input dev */ struct bcm5974_config cfg; /* device configuration */ struct mutex pm_mutex; /* serialize access to open/suspend */ @@ -478,6 +479,10 @@ static int bcm5974_open(struct input_dev *input) struct bcm5974 *dev = input_get_drvdata(input); int error; + error = usb_autopm_get_interface(dev->intf); + if (error) + return error; + mutex_lock(&dev->pm_mutex); error = bcm5974_start_traffic(dev); @@ -486,6 +491,9 @@ static int bcm5974_open(struct input_dev *input) mutex_unlock(&dev->pm_mutex); + if (error) + usb_autopm_put_interface(dev->intf); + return error; } @@ -499,6 +507,8 @@ static void bcm5974_close(struct input_dev *input) dev->opened = 0; mutex_unlock(&dev->pm_mutex); + + usb_autopm_put_interface(dev->intf); } static int bcm5974_suspend(struct usb_interface *iface, pm_message_t message) @@ -551,6 +561,7 @@ static int bcm5974_probe(struct usb_interface *iface, } dev->udev = udev; + dev->intf = iface; dev->input = input_dev; dev->cfg = *cfg; mutex_init(&dev->pm_mutex); @@ -652,6 +663,7 @@ static struct usb_driver bcm5974_driver = { .resume = bcm5974_resume, .reset_resume = bcm5974_resume, .id_table = bcm5974_table, + .supports_autosuspend = 1, }; static int __init bcm5974_init(void) -- GitLab From 8123b421e8ed944671d7241323ed3198cccb4041 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Fri, 8 Aug 2008 23:23:39 -0700 Subject: [PATCH 064/750] pkt_sched: Fix ingress deletion and filter attachment. Based upon bug reports by Stephen Hemminger. We still had some cases using ->qdisc instead of ->qdisc_sleeping. Also, qdisc_lookup() should return ingress qdiscs. Signed-off-by: David S. Miller --- net/sched/sch_api.c | 36 +++++++++++++++++++++++------------- 1 file changed, 23 insertions(+), 13 deletions(-) diff --git a/net/sched/sch_api.c b/net/sched/sch_api.c index ba1d121f312..bbf149dd781 100644 --- a/net/sched/sch_api.c +++ b/net/sched/sch_api.c @@ -183,6 +183,21 @@ EXPORT_SYMBOL(unregister_qdisc); (root qdisc, all its children, children of children etc.) */ +struct Qdisc *qdisc_match_from_root(struct Qdisc *root, u32 handle) +{ + struct Qdisc *q; + + if (!(root->flags & TCQ_F_BUILTIN) && + root->handle == handle) + return root; + + list_for_each_entry(q, &root->list, list) { + if (q->handle == handle) + return q; + } + return NULL; +} + struct Qdisc *qdisc_lookup(struct net_device *dev, u32 handle) { unsigned int i; @@ -191,16 +206,11 @@ struct Qdisc *qdisc_lookup(struct net_device *dev, u32 handle) struct netdev_queue *txq = netdev_get_tx_queue(dev, i); struct Qdisc *q, *txq_root = txq->qdisc_sleeping; - if (!(txq_root->flags & TCQ_F_BUILTIN) && - txq_root->handle == handle) - return txq_root; - - list_for_each_entry(q, &txq_root->list, list) { - if (q->handle == handle) - return q; - } + q = qdisc_match_from_root(txq_root, handle); + if (q) + return q; } - return NULL; + return qdisc_match_from_root(dev->rx_queue.qdisc_sleeping, handle); } static struct Qdisc *qdisc_leaf(struct Qdisc *p, u32 classid) @@ -908,7 +918,7 @@ static int tc_get_qdisc(struct sk_buff *skb, struct nlmsghdr *n, void *arg) return -ENOENT; q = qdisc_leaf(p, clid); } else { /* ingress */ - q = dev->rx_queue.qdisc; + q = dev->rx_queue.qdisc_sleeping; } } else { struct netdev_queue *dev_queue; @@ -978,7 +988,7 @@ replay: return -ENOENT; q = qdisc_leaf(p, clid); } else { /*ingress */ - q = dev->rx_queue.qdisc; + q = dev->rx_queue.qdisc_sleeping; } } else { struct netdev_queue *dev_queue; @@ -1529,11 +1539,11 @@ static int tc_dump_tclass(struct sk_buff *skb, struct netlink_callback *cb) t = 0; dev_queue = netdev_get_tx_queue(dev, 0); - if (tc_dump_tclass_root(dev_queue->qdisc, skb, tcm, cb, &t, s_t) < 0) + if (tc_dump_tclass_root(dev_queue->qdisc_sleeping, skb, tcm, cb, &t, s_t) < 0) goto done; dev_queue = &dev->rx_queue; - if (tc_dump_tclass_root(dev_queue->qdisc, skb, tcm, cb, &t, s_t) < 0) + if (tc_dump_tclass_root(dev_queue->qdisc_sleeping, skb, tcm, cb, &t, s_t) < 0) goto done; done: -- GitLab From d97106ea52aa57e63ff40d04479016836bbb5a4e Mon Sep 17 00:00:00 2001 From: Herbert Xu Date: Sat, 9 Aug 2008 00:35:05 -0700 Subject: [PATCH 065/750] udp: Drop socket lock for encapsulated packets The socket lock is there to protect the normal UDP receive path. Encapsulation UDP sockets don't need that protection. In fact the locking is deadly for them as they may contain another UDP packet within, possibly with the same addresses. Also the nested bit was copied from TCP. TCP needs it because of accept(2) spawning sockets. This simply doesn't apply to UDP so I've removed it. Signed-off-by: Herbert Xu Signed-off-by: David S. Miller --- net/ipv4/udp.c | 6 ++++-- net/ipv6/udp.c | 6 +++--- 2 files changed, 7 insertions(+), 5 deletions(-) diff --git a/net/ipv4/udp.c b/net/ipv4/udp.c index 383d17359d0..8e42fbbd576 100644 --- a/net/ipv4/udp.c +++ b/net/ipv4/udp.c @@ -989,7 +989,9 @@ int udp_queue_rcv_skb(struct sock * sk, struct sk_buff *skb) up->encap_rcv != NULL) { int ret; + bh_unlock_sock(sk); ret = (*up->encap_rcv)(sk, skb); + bh_lock_sock(sk); if (ret <= 0) { UDP_INC_STATS_BH(sock_net(sk), UDP_MIB_INDATAGRAMS, @@ -1092,7 +1094,7 @@ static int __udp4_lib_mcast_deliver(struct net *net, struct sk_buff *skb, if (skb1) { int ret = 0; - bh_lock_sock_nested(sk); + bh_lock_sock(sk); if (!sock_owned_by_user(sk)) ret = udp_queue_rcv_skb(sk, skb1); else @@ -1194,7 +1196,7 @@ int __udp4_lib_rcv(struct sk_buff *skb, struct hlist_head udptable[], if (sk != NULL) { int ret = 0; - bh_lock_sock_nested(sk); + bh_lock_sock(sk); if (!sock_owned_by_user(sk)) ret = udp_queue_rcv_skb(sk, skb); else diff --git a/net/ipv6/udp.c b/net/ipv6/udp.c index d1477b350f7..a6aecf76a71 100644 --- a/net/ipv6/udp.c +++ b/net/ipv6/udp.c @@ -379,7 +379,7 @@ static int __udp6_lib_mcast_deliver(struct net *net, struct sk_buff *skb, uh->source, saddr, dif))) { struct sk_buff *buff = skb_clone(skb, GFP_ATOMIC); if (buff) { - bh_lock_sock_nested(sk2); + bh_lock_sock(sk2); if (!sock_owned_by_user(sk2)) udpv6_queue_rcv_skb(sk2, buff); else @@ -387,7 +387,7 @@ static int __udp6_lib_mcast_deliver(struct net *net, struct sk_buff *skb, bh_unlock_sock(sk2); } } - bh_lock_sock_nested(sk); + bh_lock_sock(sk); if (!sock_owned_by_user(sk)) udpv6_queue_rcv_skb(sk, skb); else @@ -508,7 +508,7 @@ int __udp6_lib_rcv(struct sk_buff *skb, struct hlist_head udptable[], /* deliver */ - bh_lock_sock_nested(sk); + bh_lock_sock(sk); if (!sock_owned_by_user(sk)) udpv6_queue_rcv_skb(sk, skb); else -- GitLab From 6f088f1d215be5250582b974f83f0e3aa6ad3a28 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Sat, 9 Aug 2008 13:44:58 +0200 Subject: [PATCH 066/750] [ARM] Move include/asm-arm/plat-orion to arch/arm/plat-orion/include/plat This patch performs the equivalent include directory shuffle for plat-orion, and fixes up all users. Signed-off-by: Lennert Buytenhek --- arch/arm/mach-kirkwood/common.c | 8 ++++---- arch/arm/mach-kirkwood/irq.c | 2 +- arch/arm/mach-kirkwood/pcie.c | 2 +- arch/arm/mach-kirkwood/rd88f6281-setup.c | 2 +- arch/arm/mach-loki/common.c | 4 ++-- arch/arm/mach-loki/irq.c | 2 +- arch/arm/mach-mv78xx0/common.c | 8 ++++---- arch/arm/mach-mv78xx0/irq.c | 2 +- arch/arm/mach-mv78xx0/pcie.c | 2 +- arch/arm/mach-orion5x/common.c | 6 +++--- arch/arm/mach-orion5x/db88f5281-setup.c | 2 +- arch/arm/mach-orion5x/irq.c | 2 +- arch/arm/mach-orion5x/kurobox_pro-setup.c | 2 +- arch/arm/mach-orion5x/pci.c | 2 +- arch/arm/mm/cache-feroceon-l2.c | 2 +- .../arm/plat-orion/include/plat}/cache-feroceon-l2.h | 2 +- .../arm/plat-orion/include/plat}/ehci-orion.h | 6 +++--- .../plat-orion => arch/arm/plat-orion/include/plat}/irq.h | 6 +++--- .../arm/plat-orion/include/plat}/mv_xor.h | 6 ++++-- .../arm/plat-orion/include/plat}/orion_nand.h | 6 +++--- .../arm/plat-orion/include/plat}/pcie.h | 6 +++--- .../arm/plat-orion/include/plat}/time.h | 6 +++--- arch/arm/plat-orion/irq.c | 2 +- arch/arm/plat-orion/pcie.c | 2 +- drivers/dma/mv_xor.c | 2 +- drivers/mtd/nand/orion_nand.c | 2 +- drivers/usb/host/ehci-orion.c | 2 +- 27 files changed, 49 insertions(+), 47 deletions(-) rename {include/asm-arm/plat-orion => arch/arm/plat-orion/include/plat}/cache-feroceon-l2.h (84%) rename {include/asm-arm/plat-orion => arch/arm/plat-orion/include/plat}/ehci-orion.h (71%) rename {include/asm-arm/plat-orion => arch/arm/plat-orion/include/plat}/irq.h (76%) rename {include/asm-arm/plat-orion => arch/arm/plat-orion/include/plat}/mv_xor.h (82%) rename {include/asm-arm/plat-orion => arch/arm/plat-orion/include/plat}/orion_nand.h (79%) rename {include/asm-arm/plat-orion => arch/arm/plat-orion/include/plat}/pcie.h (91%) rename {include/asm-arm/plat-orion => arch/arm/plat-orion/include/plat}/time.h (75%) diff --git a/arch/arm/mach-kirkwood/common.c b/arch/arm/mach-kirkwood/common.c index 0e509b8ad56..02edd0dccc4 100644 --- a/arch/arm/mach-kirkwood/common.c +++ b/arch/arm/mach-kirkwood/common.c @@ -20,10 +20,10 @@ #include #include #include -#include -#include -#include -#include +#include +#include +#include +#include #include "common.h" /***************************************************************************** diff --git a/arch/arm/mach-kirkwood/irq.c b/arch/arm/mach-kirkwood/irq.c index 302bb2cf666..5790643ffe0 100644 --- a/arch/arm/mach-kirkwood/irq.c +++ b/arch/arm/mach-kirkwood/irq.c @@ -12,7 +12,7 @@ #include #include #include -#include +#include #include "common.h" void __init kirkwood_init_irq(void) diff --git a/arch/arm/mach-kirkwood/pcie.c b/arch/arm/mach-kirkwood/pcie.c index 8282d0ff84b..2195fa31f6b 100644 --- a/arch/arm/mach-kirkwood/pcie.c +++ b/arch/arm/mach-kirkwood/pcie.c @@ -12,7 +12,7 @@ #include #include #include -#include +#include #include "common.h" diff --git a/arch/arm/mach-kirkwood/rd88f6281-setup.c b/arch/arm/mach-kirkwood/rd88f6281-setup.c index d8a43018c7d..d96487a0f18 100644 --- a/arch/arm/mach-kirkwood/rd88f6281-setup.c +++ b/arch/arm/mach-kirkwood/rd88f6281-setup.c @@ -23,7 +23,7 @@ #include #include #include -#include +#include #include "common.h" static struct mtd_partition rd88f6281_nand_parts[] = { diff --git a/arch/arm/mach-loki/common.c b/arch/arm/mach-loki/common.c index e20cdbca1eb..c0d2d9d12e7 100644 --- a/arch/arm/mach-loki/common.c +++ b/arch/arm/mach-loki/common.c @@ -19,8 +19,8 @@ #include #include #include -#include -#include +#include +#include #include "common.h" /***************************************************************************** diff --git a/arch/arm/mach-loki/irq.c b/arch/arm/mach-loki/irq.c index d839af91fe0..5a487930cb2 100644 --- a/arch/arm/mach-loki/irq.c +++ b/arch/arm/mach-loki/irq.c @@ -12,7 +12,7 @@ #include #include #include -#include +#include #include "common.h" void __init loki_init_irq(void) diff --git a/arch/arm/mach-mv78xx0/common.c b/arch/arm/mach-mv78xx0/common.c index e633f9cb239..953a26c469c 100644 --- a/arch/arm/mach-mv78xx0/common.c +++ b/arch/arm/mach-mv78xx0/common.c @@ -18,10 +18,10 @@ #include #include #include -#include -#include -#include -#include +#include +#include +#include +#include #include "common.h" diff --git a/arch/arm/mach-mv78xx0/irq.c b/arch/arm/mach-mv78xx0/irq.c index 3198abf54c9..28248d37b99 100644 --- a/arch/arm/mach-mv78xx0/irq.c +++ b/arch/arm/mach-mv78xx0/irq.c @@ -12,7 +12,7 @@ #include #include #include -#include +#include #include "common.h" void __init mv78xx0_init_irq(void) diff --git a/arch/arm/mach-mv78xx0/pcie.c b/arch/arm/mach-mv78xx0/pcie.c index b78e1443159..430ea84d587 100644 --- a/arch/arm/mach-mv78xx0/pcie.c +++ b/arch/arm/mach-mv78xx0/pcie.c @@ -12,7 +12,7 @@ #include #include #include -#include +#include #include "common.h" struct pcie_port { diff --git a/arch/arm/mach-orion5x/common.c b/arch/arm/mach-orion5x/common.c index 168eeacaa4c..b44f26d7613 100644 --- a/arch/arm/mach-orion5x/common.c +++ b/arch/arm/mach-orion5x/common.c @@ -26,9 +26,9 @@ #include #include #include -#include -#include -#include +#include +#include +#include #include "common.h" /***************************************************************************** diff --git a/arch/arm/mach-orion5x/db88f5281-setup.c b/arch/arm/mach-orion5x/db88f5281-setup.c index 48ce6d0e002..ff13e9060b1 100644 --- a/arch/arm/mach-orion5x/db88f5281-setup.c +++ b/arch/arm/mach-orion5x/db88f5281-setup.c @@ -25,7 +25,7 @@ #include #include #include -#include +#include #include "common.h" #include "mpp.h" diff --git a/arch/arm/mach-orion5x/irq.c b/arch/arm/mach-orion5x/irq.c index cc2a017fd2a..2545ff9e583 100644 --- a/arch/arm/mach-orion5x/irq.c +++ b/arch/arm/mach-orion5x/irq.c @@ -16,7 +16,7 @@ #include #include #include -#include +#include #include "common.h" /***************************************************************************** diff --git a/arch/arm/mach-orion5x/kurobox_pro-setup.c b/arch/arm/mach-orion5x/kurobox_pro-setup.c index 0caaaac74bc..45dfc9f99d8 100644 --- a/arch/arm/mach-orion5x/kurobox_pro-setup.c +++ b/arch/arm/mach-orion5x/kurobox_pro-setup.c @@ -25,7 +25,7 @@ #include #include #include -#include +#include #include "common.h" #include "mpp.h" diff --git a/arch/arm/mach-orion5x/pci.c b/arch/arm/mach-orion5x/pci.c index 256a4f68093..fbceecc4b7e 100644 --- a/arch/arm/mach-orion5x/pci.c +++ b/arch/arm/mach-orion5x/pci.c @@ -14,7 +14,7 @@ #include #include #include -#include +#include #include "common.h" /***************************************************************************** diff --git a/arch/arm/mm/cache-feroceon-l2.c b/arch/arm/mm/cache-feroceon-l2.c index 20eec4ba173..7b5a25d8157 100644 --- a/arch/arm/mm/cache-feroceon-l2.c +++ b/arch/arm/mm/cache-feroceon-l2.c @@ -14,7 +14,7 @@ #include #include -#include +#include /* diff --git a/include/asm-arm/plat-orion/cache-feroceon-l2.h b/arch/arm/plat-orion/include/plat/cache-feroceon-l2.h similarity index 84% rename from include/asm-arm/plat-orion/cache-feroceon-l2.h rename to arch/arm/plat-orion/include/plat/cache-feroceon-l2.h index ba4e016d3ec..06f982d5569 100644 --- a/include/asm-arm/plat-orion/cache-feroceon-l2.h +++ b/arch/arm/plat-orion/include/plat/cache-feroceon-l2.h @@ -1,5 +1,5 @@ /* - * include/asm-arm/plat-orion/cache-feroceon-l2.h + * arch/arm/plat-orion/include/plat/cache-feroceon-l2.h * * Copyright (C) 2008 Marvell Semiconductor * diff --git a/include/asm-arm/plat-orion/ehci-orion.h b/arch/arm/plat-orion/include/plat/ehci-orion.h similarity index 71% rename from include/asm-arm/plat-orion/ehci-orion.h rename to arch/arm/plat-orion/include/plat/ehci-orion.h index 785705651e2..64343051095 100644 --- a/include/asm-arm/plat-orion/ehci-orion.h +++ b/arch/arm/plat-orion/include/plat/ehci-orion.h @@ -1,13 +1,13 @@ /* - * include/asm-arm/plat-orion/ehci-orion.h + * arch/arm/plat-orion/include/plat/ehci-orion.h * * This file is licensed under the terms of the GNU General Public * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ -#ifndef __ASM_PLAT_ORION_EHCI_ORION_H -#define __ASM_PLAT_ORION_EHCI_ORION_H +#ifndef __PLAT_EHCI_ORION_H +#define __PLAT_EHCI_ORION_H #include diff --git a/include/asm-arm/plat-orion/irq.h b/arch/arm/plat-orion/include/plat/irq.h similarity index 76% rename from include/asm-arm/plat-orion/irq.h rename to arch/arm/plat-orion/include/plat/irq.h index 94aeed919d5..f05eeab9496 100644 --- a/include/asm-arm/plat-orion/irq.h +++ b/arch/arm/plat-orion/include/plat/irq.h @@ -1,5 +1,5 @@ /* - * include/asm-arm/plat-orion/irq.h + * arch/arm/plat-orion/include/plat/irq.h * * Marvell Orion SoC IRQ handling. * @@ -8,8 +8,8 @@ * warranty of any kind, whether express or implied. */ -#ifndef __ASM_PLAT_ORION_IRQ_H -#define __ASM_PLAT_ORION_IRQ_H +#ifndef __PLAT_IRQ_H +#define __PLAT_IRQ_H void orion_irq_init(unsigned int irq_start, void __iomem *maskaddr); diff --git a/include/asm-arm/plat-orion/mv_xor.h b/arch/arm/plat-orion/include/plat/mv_xor.h similarity index 82% rename from include/asm-arm/plat-orion/mv_xor.h rename to arch/arm/plat-orion/include/plat/mv_xor.h index c349e8ff5cc..bd5f3bdb4ae 100644 --- a/include/asm-arm/plat-orion/mv_xor.h +++ b/arch/arm/plat-orion/include/plat/mv_xor.h @@ -1,9 +1,11 @@ /* + * arch/arm/plat-orion/include/plat/mv_xor.h + * * Marvell XOR platform device data definition file. */ -#ifndef __ASM_PLAT_ORION_MV_XOR_H -#define __ASM_PLAT_ORION_MV_XOR_H +#ifndef __PLAT_MV_XOR_H +#define __PLAT_MV_XOR_H #include #include diff --git a/include/asm-arm/plat-orion/orion_nand.h b/arch/arm/plat-orion/include/plat/orion_nand.h similarity index 79% rename from include/asm-arm/plat-orion/orion_nand.h rename to arch/arm/plat-orion/include/plat/orion_nand.h index ad4ce94c199..d6a4cfa3778 100644 --- a/include/asm-arm/plat-orion/orion_nand.h +++ b/arch/arm/plat-orion/include/plat/orion_nand.h @@ -1,13 +1,13 @@ /* - * include/asm-arm/plat-orion/orion_nand.h + * arch/arm/plat-orion/include/plat/orion_nand.h * * This file is licensed under the terms of the GNU General Public * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ -#ifndef __ASM_PLAT_ORION_ORION_NAND_H -#define __ASM_PLAT_ORION_ORION_NAND_H +#ifndef __PLAT_ORION_NAND_H +#define __PLAT_ORION_NAND_H /* * Device bus NAND private data diff --git a/include/asm-arm/plat-orion/pcie.h b/arch/arm/plat-orion/include/plat/pcie.h similarity index 91% rename from include/asm-arm/plat-orion/pcie.h rename to arch/arm/plat-orion/include/plat/pcie.h index e61b7bd97af..3ebfef72b4e 100644 --- a/include/asm-arm/plat-orion/pcie.h +++ b/arch/arm/plat-orion/include/plat/pcie.h @@ -1,5 +1,5 @@ /* - * include/asm-arm/plat-orion/pcie.h + * arch/arm/plat-orion/include/plat/pcie.h * * Marvell Orion SoC PCIe handling. * @@ -8,8 +8,8 @@ * warranty of any kind, whether express or implied. */ -#ifndef __ASM_PLAT_ORION_PCIE_H -#define __ASM_PLAT_ORION_PCIE_H +#ifndef __PLAT_PCIE_H +#define __PLAT_PCIE_H u32 orion_pcie_dev_id(void __iomem *base); u32 orion_pcie_rev(void __iomem *base); diff --git a/include/asm-arm/plat-orion/time.h b/arch/arm/plat-orion/include/plat/time.h similarity index 75% rename from include/asm-arm/plat-orion/time.h rename to arch/arm/plat-orion/include/plat/time.h index 0e85cc8f44d..c06ca35f361 100644 --- a/include/asm-arm/plat-orion/time.h +++ b/arch/arm/plat-orion/include/plat/time.h @@ -1,5 +1,5 @@ /* - * include/asm-arm/plat-orion/time.h + * arch/arm/plat-orion/include/plat/time.h * * Marvell Orion SoC time handling. * @@ -8,8 +8,8 @@ * warranty of any kind, whether express or implied. */ -#ifndef __ASM_PLAT_ORION_TIME_H -#define __ASM_PLAT_ORION_TIME_H +#ifndef __PLAT_TIME_H +#define __PLAT_TIME_H void orion_time_init(unsigned int irq, unsigned int tclk); diff --git a/arch/arm/plat-orion/irq.c b/arch/arm/plat-orion/irq.c index fe66a183516..3f9d34fc738 100644 --- a/arch/arm/plat-orion/irq.c +++ b/arch/arm/plat-orion/irq.c @@ -12,7 +12,7 @@ #include #include #include -#include +#include static void orion_irq_mask(u32 irq) { diff --git a/arch/arm/plat-orion/pcie.c b/arch/arm/plat-orion/pcie.c index ca32c60e14d..883902fead8 100644 --- a/arch/arm/plat-orion/pcie.c +++ b/arch/arm/plat-orion/pcie.c @@ -12,7 +12,7 @@ #include #include #include -#include +#include /* * PCIe unit register offsets. diff --git a/drivers/dma/mv_xor.c b/drivers/dma/mv_xor.c index a4e4494663b..0328da020a1 100644 --- a/drivers/dma/mv_xor.c +++ b/drivers/dma/mv_xor.c @@ -25,7 +25,7 @@ #include #include #include -#include +#include #include "mv_xor.h" static void mv_xor_issue_pending(struct dma_chan *chan); diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c index 64002488c6e..917cf8d3ae9 100644 --- a/drivers/mtd/nand/orion_nand.c +++ b/drivers/mtd/nand/orion_nand.c @@ -19,7 +19,7 @@ #include #include #include -#include +#include #ifdef CONFIG_MTD_CMDLINE_PARTS static const char *part_probes[] = { "cmdlinepart", NULL }; diff --git a/drivers/usb/host/ehci-orion.c b/drivers/usb/host/ehci-orion.c index 5fbdc14e63b..5416cf96900 100644 --- a/drivers/usb/host/ehci-orion.c +++ b/drivers/usb/host/ehci-orion.c @@ -12,7 +12,7 @@ #include #include #include -#include +#include #define rdl(off) __raw_readl(hcd->regs + (off)) #define wrl(off, val) __raw_writel((val), hcd->regs + (off)) -- GitLab From 631c9a8a79b9b94eef56afa3bff107ce27c4c2bb Mon Sep 17 00:00:00 2001 From: Krzysztof Helt Date: Fri, 8 Aug 2008 21:34:10 +0100 Subject: [PATCH 067/750] [ARM] S3C24XX: Compilation fix if s3c2410 is not selected This patch fixes compilation error if no s3c2410 processor is selected but the s3c244x is selected. The function s3c2410_baseclk_add() is now available for all Samsung cpus. Signed-off-by: Krzysztof Helt [ben-linux@fluff.org: Whitespace and description fixups] Signed-off-by: Ben Dooks --- include/asm-arm/plat-s3c24xx/s3c2410.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/include/asm-arm/plat-s3c24xx/s3c2410.h b/include/asm-arm/plat-s3c24xx/s3c2410.h index 36de0b83587..3cd1ec677b3 100644 --- a/include/asm-arm/plat-s3c24xx/s3c2410.h +++ b/include/asm-arm/plat-s3c24xx/s3c2410.h @@ -21,11 +21,11 @@ extern void s3c2410_init_uarts(struct s3c2410_uartcfg *cfg, int no); extern void s3c2410_init_clocks(int xtal); -extern int s3c2410_baseclk_add(void); - #else #define s3c2410_init_clocks NULL #define s3c2410_init_uarts NULL #define s3c2410_map_io NULL #define s3c2410_init NULL #endif + +extern int s3c2410_baseclk_add(void); -- GitLab From 29210475945f13c61a7994b54ccf37692a075aeb Mon Sep 17 00:00:00 2001 From: Huang Weiyi Date: Fri, 8 Aug 2008 21:22:34 +0100 Subject: [PATCH 068/750] [ARM] JIVE: Remove duplicated mtd includes Removed duplicated include file and in arch/arm/mach-s3c2412/mach-jive.c. Signed-off-by: Huang Weiyi Signed-off-by: Ben Dooks --- arch/arm/mach-s3c2412/mach-jive.c | 3 --- 1 file changed, 3 deletions(-) diff --git a/arch/arm/mach-s3c2412/mach-jive.c b/arch/arm/mach-s3c2412/mach-jive.c index 30f613a79bf..4c061d29463 100644 --- a/arch/arm/mach-s3c2412/mach-jive.c +++ b/arch/arm/mach-s3c2412/mach-jive.c @@ -26,9 +26,6 @@ #include -#include -#include - #include #include #include -- GitLab From e38d523fd0932a5d4ef2865360d8828efcf05392 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Fri, 8 Aug 2008 21:22:35 +0100 Subject: [PATCH 069/750] [ARM] CATS: Do not try and map bad PCI IRQ numbers The cats_map_irq() function in the Simtec CATS support code is mapping IRQ 255 (invalid IRQ) into what is a supposedly valid interrupt numner which can cause problems with other devices then seeing an interrupt they cannot claim. If the IRQ number if >= 255, then return -1 as this is not something we can map. Signed-off-by: Ben Dooks --- arch/arm/mach-footbridge/cats-pci.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm/mach-footbridge/cats-pci.c b/arch/arm/mach-footbridge/cats-pci.c index 35eb232a649..ae3e1c8c758 100644 --- a/arch/arm/mach-footbridge/cats-pci.c +++ b/arch/arm/mach-footbridge/cats-pci.c @@ -18,6 +18,9 @@ static int irqmap_cats[] __initdata = { IRQ_PCI, IRQ_IN0, IRQ_IN1, IRQ_IN3 }; static int __init cats_map_irq(struct pci_dev *dev, u8 slot, u8 pin) { + if (dev->irq >= 255) + return -1; /* not a valid interrupt. */ + if (dev->irq >= 128) return dev->irq & 0x1f; -- GitLab From ed414fb7b840b2ca8bf033efcd9fe9ea8d6fe800 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Fri, 8 Aug 2008 21:22:36 +0100 Subject: [PATCH 070/750] [ARM] S3C24XX: Fix section mismatch for s3c_lookup_cpu s3c_lookup_cpu is only used at init time, so make it __init. Signed-off-by: Ben Dooks --- arch/arm/plat-s3c24xx/cpu.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/arch/arm/plat-s3c24xx/cpu.c b/arch/arm/plat-s3c24xx/cpu.c index 6d60f0476bb..89ce60eabd5 100644 --- a/arch/arm/plat-s3c24xx/cpu.c +++ b/arch/arm/plat-s3c24xx/cpu.c @@ -169,9 +169,7 @@ static struct map_desc s3c_iodesc[] __initdata = { IODESC_ENT(UART) }; - -static struct cpu_table * -s3c_lookup_cpu(unsigned long idcode) +static struct cpu_table * __init s3c_lookup_cpu(unsigned long idcode) { struct cpu_table *tab; int count; -- GitLab From cbc212e877b37fff84fd4b7ad2c44e4cd1888c85 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Fri, 8 Aug 2008 21:22:37 +0100 Subject: [PATCH 071/750] [ARM] S3C24XX: Documentation: update platform docs Update documentation in arch/arm/plat-s3c24xx Signed-off-by: Ben Dooks --- Documentation/arm/Samsung-S3C24XX/Overview.txt | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) diff --git a/Documentation/arm/Samsung-S3C24XX/Overview.txt b/Documentation/arm/Samsung-S3C24XX/Overview.txt index 014a8ec4877..c667078e0cf 100644 --- a/Documentation/arm/Samsung-S3C24XX/Overview.txt +++ b/Documentation/arm/Samsung-S3C24XX/Overview.txt @@ -12,6 +12,7 @@ Introduction Support for the S3C2400 series is in progress. + Configuration ------------- @@ -38,6 +39,22 @@ Layout Register, kernel and platform data definitions are held in the arch/arm/mach-s3c2410 directory./include/mach +arch/arm/plat-s3c24xx: + + Files in here are either common to all the s3c24xx family, + or are common to only some of them with names to indicate this + status. The files that are not common to all are generally named + with the initial cpu they support in the series to ensure a short + name without any possibility of confusion with newer devices. + + As an example, initially s3c244x would cover s3c2440 and s3c2442, but + with the s3c2443 which does not share many of the same drivers in + this directory, the name becomes invalid. We stick to s3c2440- + to indicate a driver that is s3c2440 and s3c2442 compatible. + + This does mean that to find the status of any given SoC, a number + of directories may need to be searched. + Machines -------- -- GitLab From bc4c7265a0876e84cedbbc76f517a702b6e133b4 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Fri, 8 Aug 2008 21:22:38 +0100 Subject: [PATCH 072/750] [ARM] S3C24XX: Documentation: Update suported CPU list Update supported and in-progress cpu list. Signed-off-by: Ben Dooks --- Documentation/arm/Samsung-S3C24XX/Overview.txt | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/Documentation/arm/Samsung-S3C24XX/Overview.txt b/Documentation/arm/Samsung-S3C24XX/Overview.txt index c667078e0cf..7b62fb8ab4c 100644 --- a/Documentation/arm/Samsung-S3C24XX/Overview.txt +++ b/Documentation/arm/Samsung-S3C24XX/Overview.txt @@ -8,9 +8,9 @@ Introduction The Samsung S3C24XX range of ARM9 System-on-Chip CPUs are supported by the 's3c2410' architecture of ARM Linux. Currently the S3C2410, - S3C2412, S3C2413, S3C2440 and S3C2442 devices are supported. + S3C2412, S3C2413, S3C2440, S3C2442 and S3C2443 devices are supported. - Support for the S3C2400 series is in progress. + Support for the S3C2400 and S3C24A0 series are in progress. Configuration -- GitLab From a0f774b59ee9e80d7423feba312c6132ca068e96 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Fri, 8 Aug 2008 21:22:39 +0100 Subject: [PATCH 073/750] [ARM] S3C24XX: Documentation: update SD/MMC status Update SD/MMC status now that the driver is merged. Signed-off-by: Ben Dooks --- Documentation/arm/Samsung-S3C24XX/Overview.txt | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/Documentation/arm/Samsung-S3C24XX/Overview.txt b/Documentation/arm/Samsung-S3C24XX/Overview.txt index 7b62fb8ab4c..c5429f54103 100644 --- a/Documentation/arm/Samsung-S3C24XX/Overview.txt +++ b/Documentation/arm/Samsung-S3C24XX/Overview.txt @@ -176,6 +176,17 @@ NAND For more information see Documentation/arm/Samsung-S3C24XX/NAND.txt +SD/MMC +------ + + The SD/MMC hardware pre S3C2443 is supported in the current + kernel, the driver is drivers/mmc/host/s3cmci.c and supports + 1 and 4 bit SD or MMC cards. + + The SDIO behaviour of this driver has not been fully tested. There is no + current support for hardware SDIO interrupts. + + Serial ------ -- GitLab From f47c32f3ae604669c3af0b7a07917270a235bd84 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Fri, 8 Aug 2008 21:22:40 +0100 Subject: [PATCH 074/750] [ARM] S3C24XX: Documentation: Update GPIO status Update the status of the S3C24XX GPIO now we have moved to supporting GPIOLIB Signed-off-by: Ben Dooks --- Documentation/arm/Samsung-S3C24XX/GPIO.txt | 15 +++++++++++++++ Documentation/arm/Samsung-S3C24XX/Overview.txt | 3 +++ 2 files changed, 18 insertions(+) diff --git a/Documentation/arm/Samsung-S3C24XX/GPIO.txt b/Documentation/arm/Samsung-S3C24XX/GPIO.txt index b5d20c0b2ab..ea7ccfc4b27 100644 --- a/Documentation/arm/Samsung-S3C24XX/GPIO.txt +++ b/Documentation/arm/Samsung-S3C24XX/GPIO.txt @@ -13,6 +13,21 @@ Introduction data-sheet/users manual to find out the complete list. +GPIOLIB +------- + + With the event of the GPIOLIB in drivers/gpio, support for some + of the GPIO functions such as reading and writing a pin will + be removed in favour of this common access method. + + Once all the extant drivers have been converted, the functions + listed below will be removed (they may be marked as __deprecated + in the near future). + + - s3c2410_gpio_getpin + - s3c2410_gpio_setpin + + Headers ------- diff --git a/Documentation/arm/Samsung-S3C24XX/Overview.txt b/Documentation/arm/Samsung-S3C24XX/Overview.txt index c5429f54103..cff6227b448 100644 --- a/Documentation/arm/Samsung-S3C24XX/Overview.txt +++ b/Documentation/arm/Samsung-S3C24XX/Overview.txt @@ -206,6 +206,9 @@ GPIO The core contains support for manipulating the GPIO, see the documentation in GPIO.txt in the same directory as this file. + Newer kernels carry GPIOLIB, and support is being moved towards + this with some of the older support in line to be removed. + Clock Management ---------------- -- GitLab From ce72e36ed1a57ba086270039c7d6fac9bf1c5fbc Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Sat, 9 Aug 2008 15:17:27 +0200 Subject: [PATCH 075/750] [ARM] Orion: support D0 5281 silicon On D0 5281 SoCs, we need to disable the wait-for-interrupt instruction due to an erratum. Signed-off-by: Lennert Buytenhek Signed-off-by: Nicolas Pitre Acked-by: Martin Michlmayr --- arch/arm/mach-orion5x/common.c | 11 +++++++++++ arch/arm/mach-orion5x/include/mach/orion5x.h | 1 + 2 files changed, 12 insertions(+) diff --git a/arch/arm/mach-orion5x/common.c b/arch/arm/mach-orion5x/common.c index b44f26d7613..8f2146bd8a9 100644 --- a/arch/arm/mach-orion5x/common.c +++ b/arch/arm/mach-orion5x/common.c @@ -382,6 +382,8 @@ static void __init orion5x_id(u32 *dev, u32 *rev, char **dev_name) *dev_name = "MV88F5281-D2"; } else if (*rev == MV88F5281_REV_D1) { *dev_name = "MV88F5281-D1"; + } else if (*rev == MV88F5281_REV_D0) { + *dev_name = "MV88F5281-D0"; } else { *dev_name = "MV88F5281-Rev-Unsupported"; } @@ -416,6 +418,15 @@ void __init orion5x_init(void) * Setup Orion address map */ orion5x_setup_cpu_mbus_bridge(); + + /* + * Don't issue "Wait for Interrupt" instruction if we are + * running on D0 5281 silicon. + */ + if (dev == MV88F5281_DEV_ID && rev == MV88F5281_REV_D0) { + printk(KERN_INFO "Orion: Applying 5281 D0 WFI workaround.\n"); + disable_hlt(); + } } /* diff --git a/arch/arm/mach-orion5x/include/mach/orion5x.h b/arch/arm/mach-orion5x/include/mach/orion5x.h index f52a7d65bec..77978dbd5a9 100644 --- a/arch/arm/mach-orion5x/include/mach/orion5x.h +++ b/arch/arm/mach-orion5x/include/mach/orion5x.h @@ -73,6 +73,7 @@ #define MV88F5182_REV_A2 2 /* Orion-2 (88F5281) */ #define MV88F5281_DEV_ID 0x5281 +#define MV88F5281_REV_D0 4 #define MV88F5281_REV_D1 5 #define MV88F5281_REV_D2 6 -- GitLab From 4a4e30afefbfd069ef09de3514cce4886e83ff10 Mon Sep 17 00:00:00 2001 From: Martin Michlmayr Date: Mon, 21 Jul 2008 19:58:48 +0300 Subject: [PATCH 076/750] [ARM] Orion: export red SATA lights on TS-409, fix SATA presence/activity Export the four red SATA LEDs on the QNAP TS-409 that are connected through gpio. Since the boot loader apparently sets the SATA LEDs 2-4 to red and the SATA LED can only be red or green (but not both), exporting the red SATA LEDs (which automatically turns them off upon boot) makes the green SATA presence/activity indication visible. Signed-off-by: Martin Michlmayr Acked-by: Sylver Bruneau Signed-off-by: Lennert Buytenhek --- arch/arm/mach-orion5x/ts409-setup.c | 42 +++++++++++++++++++++++++++++ 1 file changed, 42 insertions(+) diff --git a/arch/arm/mach-orion5x/ts409-setup.c b/arch/arm/mach-orion5x/ts409-setup.c index 6053e76ac96..3133b73282e 100644 --- a/arch/arm/mach-orion5x/ts409-setup.c +++ b/arch/arm/mach-orion5x/ts409-setup.c @@ -3,6 +3,9 @@ * * Maintainer: Sylver Bruneau * + * Copyright (C) 2008 Sylver Bruneau + * Copyright (C) 2008 Martin Michlmayr + * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * as published by the Free Software Foundation; either version @@ -16,6 +19,7 @@ #include #include #include +#include #include #include #include @@ -162,6 +166,43 @@ static struct i2c_board_info __initdata qnap_ts409_i2c_rtc = { I2C_BOARD_INFO("s35390a", 0x30), }; +/***************************************************************************** + * LEDs attached to GPIO + ****************************************************************************/ + +static struct gpio_led ts409_led_pins[] = { + { + .name = "ts409:red:sata1", + .gpio = 4, + .active_low = 1, + }, { + .name = "ts409:red:sata2", + .gpio = 5, + .active_low = 1, + }, { + .name = "ts409:red:sata3", + .gpio = 6, + .active_low = 1, + }, { + .name = "ts409:red:sata4", + .gpio = 7, + .active_low = 1, + }, +}; + +static struct gpio_led_platform_data ts409_led_data = { + .leds = ts409_led_pins, + .num_leds = ARRAY_SIZE(ts409_led_pins), +}; + +static struct platform_device ts409_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &ts409_led_data, + }, +}; + /**************************************************************************** * GPIO Attached Keys * Power button is attached to the PIC microcontroller @@ -255,6 +296,7 @@ static void __init qnap_ts409_init(void) if (qnap_ts409_i2c_rtc.irq == 0) pr_warning("qnap_ts409_init: failed to get RTC IRQ\n"); i2c_register_board_info(0, &qnap_ts409_i2c_rtc, 1); + platform_device_register(&ts409_leds); /* register tsx09 specific power-off method */ pm_power_off = qnap_tsx09_power_off; -- GitLab From 28ca8c802f71283d610656a207f3325c09e4585e Mon Sep 17 00:00:00 2001 From: Martin Michlmayr Date: Tue, 22 Jul 2008 01:49:22 +0300 Subject: [PATCH 077/750] [ARM] Orion: use better key codes for the TS-209/TS-409 buttons Use key codes for the buttons on the TS-209/TS-409 that make more sense than the current values. Signed-off-by: Martin Michlmayr Acked-by: Byron Bradley Signed-off-by: Lennert Buytenhek --- arch/arm/mach-orion5x/ts209-setup.c | 4 ++-- arch/arm/mach-orion5x/ts409-setup.c | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm/mach-orion5x/ts209-setup.c b/arch/arm/mach-orion5x/ts209-setup.c index 809132de31d..1bb7de8a262 100644 --- a/arch/arm/mach-orion5x/ts209-setup.c +++ b/arch/arm/mach-orion5x/ts209-setup.c @@ -207,12 +207,12 @@ static struct i2c_board_info __initdata qnap_ts209_i2c_rtc = { static struct gpio_keys_button qnap_ts209_buttons[] = { { - .code = KEY_RESTART, + .code = KEY_COPY, .gpio = QNAP_TS209_GPIO_KEY_MEDIA, .desc = "USB Copy Button", .active_low = 1, }, { - .code = KEY_POWER, + .code = KEY_RESTART, .gpio = QNAP_TS209_GPIO_KEY_RESET, .desc = "Reset Button", .active_low = 1, diff --git a/arch/arm/mach-orion5x/ts409-setup.c b/arch/arm/mach-orion5x/ts409-setup.c index 3133b73282e..57d460c0199 100644 --- a/arch/arm/mach-orion5x/ts409-setup.c +++ b/arch/arm/mach-orion5x/ts409-setup.c @@ -212,7 +212,7 @@ static struct platform_device ts409_leds = { static struct gpio_keys_button qnap_ts409_buttons[] = { { - .code = KEY_RESTART, + .code = KEY_COPY, .gpio = QNAP_TS409_GPIO_KEY_MEDIA, .desc = "USB Copy Button", .active_low = 1, -- GitLab From 5cebbd09fc06f4159f10f9f86bbd1517ac0279a2 Mon Sep 17 00:00:00 2001 From: Martin Michlmayr Date: Thu, 31 Jul 2008 07:38:08 +0300 Subject: [PATCH 078/750] [ARM] Orion: Export the reset button of the QNAP TS-409 The reset button on the QNAP TS-409 is available through gpio. Signed-off-by: Martin Michlmayr Signed-off-by: Lennert Buytenhek --- arch/arm/mach-orion5x/ts409-setup.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/mach-orion5x/ts409-setup.c b/arch/arm/mach-orion5x/ts409-setup.c index 57d460c0199..b27d2b76208 100644 --- a/arch/arm/mach-orion5x/ts409-setup.c +++ b/arch/arm/mach-orion5x/ts409-setup.c @@ -208,10 +208,16 @@ static struct platform_device ts409_leds = { * Power button is attached to the PIC microcontroller ****************************************************************************/ +#define QNAP_TS409_GPIO_KEY_RESET 14 #define QNAP_TS409_GPIO_KEY_MEDIA 15 static struct gpio_keys_button qnap_ts409_buttons[] = { { + .code = KEY_RESTART, + .gpio = QNAP_TS409_GPIO_KEY_RESET, + .desc = "Reset Button", + .active_low = 1, + }, { .code = KEY_COPY, .gpio = QNAP_TS409_GPIO_KEY_MEDIA, .desc = "USB Copy Button", -- GitLab From 94434ba09add528dbd48b9765a31c86372f94dd0 Mon Sep 17 00:00:00 2001 From: Martin Michlmayr Date: Sun, 13 Jul 2008 16:53:31 +0300 Subject: [PATCH 079/750] [ARM] Orion: enable KEYBOARD_GPIO in the defconfg Enable KEYBOARD_GPIO in the Orion defconfig because a number of Orion devices, such as the HP mv2120, define gpio-keys buttons. Signed-off-by: Martin Michlmayr Signed-off-by: Lennert Buytenhek --- arch/arm/configs/orion5x_defconfig | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) diff --git a/arch/arm/configs/orion5x_defconfig b/arch/arm/configs/orion5x_defconfig index 9578b5d9f9c..f2f7a542869 100644 --- a/arch/arm/configs/orion5x_defconfig +++ b/arch/arm/configs/orion5x_defconfig @@ -757,7 +757,14 @@ CONFIG_INPUT_EVDEV=y # # Input Device Drivers # -# CONFIG_INPUT_KEYBOARD is not set +CONFIG_INPUT_KEYBOARD=y +# CONFIG_KEYBOARD_ATKBD is not set +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_LKKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set +# CONFIG_KEYBOARD_NEWTON is not set +# CONFIG_KEYBOARD_STOWAWAY is not set +CONFIG_KEYBOARD_GPIO=y # CONFIG_INPUT_MOUSE is not set # CONFIG_INPUT_JOYSTICK is not set # CONFIG_INPUT_TABLET is not set -- GitLab From 627ca2fe93e7ef5e746c27f08a4f86cbc04dd915 Mon Sep 17 00:00:00 2001 From: Martin Michlmayr Date: Sun, 13 Jul 2008 15:59:00 +0300 Subject: [PATCH 080/750] [ARM] Orion: enable RTC_DRV_PCF8563 in the defconfig for HP mv2120 Enable RTC_DRV_PCF8563 in the Orion defconfig since this driver is needed by the HP mv2120. Signed-off-by: Martin Michlmayr Signed-off-by: Lennert Buytenhek --- arch/arm/configs/orion5x_defconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/configs/orion5x_defconfig b/arch/arm/configs/orion5x_defconfig index f2f7a542869..d99543911b1 100644 --- a/arch/arm/configs/orion5x_defconfig +++ b/arch/arm/configs/orion5x_defconfig @@ -1118,7 +1118,7 @@ CONFIG_RTC_DRV_DS1307=y CONFIG_RTC_DRV_RS5C372=y # CONFIG_RTC_DRV_ISL1208 is not set # CONFIG_RTC_DRV_X1205 is not set -# CONFIG_RTC_DRV_PCF8563 is not set +CONFIG_RTC_DRV_PCF8563=y # CONFIG_RTC_DRV_PCF8583 is not set CONFIG_RTC_DRV_M41T80=y # CONFIG_RTC_DRV_M41T80_WDT is not set -- GitLab From 3af6b0440f7b318af3f6a4c4ce251753377dba3a Mon Sep 17 00:00:00 2001 From: Martin Michlmayr Date: Thu, 31 Jul 2008 07:38:24 +0300 Subject: [PATCH 081/750] [ARM] Orion: enable CONFIG_RTC_DRV_S35390A in the defconfg for QNAP devices The QNAP TS-109/TS-209 and TS-409 devices need RTC_DRV_S35390A. Signed-off-by: Martin Michlmayr Signed-off-by: Lennert Buytenhek --- arch/arm/configs/orion5x_defconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/configs/orion5x_defconfig b/arch/arm/configs/orion5x_defconfig index d99543911b1..1464ffe7171 100644 --- a/arch/arm/configs/orion5x_defconfig +++ b/arch/arm/configs/orion5x_defconfig @@ -1122,7 +1122,7 @@ CONFIG_RTC_DRV_PCF8563=y # CONFIG_RTC_DRV_PCF8583 is not set CONFIG_RTC_DRV_M41T80=y # CONFIG_RTC_DRV_M41T80_WDT is not set -# CONFIG_RTC_DRV_S35390A is not set +CONFIG_RTC_DRV_S35390A=y # # SPI RTC drivers -- GitLab From 1d5a1a6e92abb1ecb011a673e637146c4e232f1e Mon Sep 17 00:00:00 2001 From: Saeed Bishara Date: Mon, 16 Jun 2008 23:25:12 -1100 Subject: [PATCH 082/750] [ARM] Orion: Instantiate mv_xor driver for 5182 Signed-off-by: Saeed Bishara Signed-off-by: Lennert Buytenhek --- arch/arm/mach-orion5x/common.c | 98 ++++++++++++++++++++ arch/arm/mach-orion5x/common.h | 1 + arch/arm/mach-orion5x/include/mach/orion5x.h | 4 + arch/arm/mach-orion5x/kurobox_pro-setup.c | 1 + arch/arm/mach-orion5x/mss2-setup.c | 1 + arch/arm/mach-orion5x/mv2120-setup.c | 1 + arch/arm/mach-orion5x/rd88f5182-setup.c | 1 + arch/arm/mach-orion5x/ts209-setup.c | 1 + arch/arm/mach-orion5x/ts78xx-setup.c | 1 + 9 files changed, 109 insertions(+) diff --git a/arch/arm/mach-orion5x/common.c b/arch/arm/mach-orion5x/common.c index 8f2146bd8a9..7b11e552bc5 100644 --- a/arch/arm/mach-orion5x/common.c +++ b/arch/arm/mach-orion5x/common.c @@ -27,6 +27,7 @@ #include #include #include +#include #include #include #include "common.h" @@ -354,6 +355,103 @@ void __init orion5x_uart1_init(void) } +/***************************************************************************** + * XOR engine + ****************************************************************************/ +static struct resource orion5x_xor_shared_resources[] = { + { + .name = "xor low", + .start = ORION5X_XOR_PHYS_BASE, + .end = ORION5X_XOR_PHYS_BASE + 0xff, + .flags = IORESOURCE_MEM, + }, { + .name = "xor high", + .start = ORION5X_XOR_PHYS_BASE + 0x200, + .end = ORION5X_XOR_PHYS_BASE + 0x2ff, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device orion5x_xor_shared = { + .name = MV_XOR_SHARED_NAME, + .id = 0, + .num_resources = ARRAY_SIZE(orion5x_xor_shared_resources), + .resource = orion5x_xor_shared_resources, +}; + +static u64 orion5x_xor_dmamask = DMA_32BIT_MASK; + +static struct resource orion5x_xor0_resources[] = { + [0] = { + .start = IRQ_ORION5X_XOR0, + .end = IRQ_ORION5X_XOR0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct mv_xor_platform_data orion5x_xor0_data = { + .shared = &orion5x_xor_shared, + .hw_id = 0, + .pool_size = PAGE_SIZE, +}; + +static struct platform_device orion5x_xor0_channel = { + .name = MV_XOR_NAME, + .id = 0, + .num_resources = ARRAY_SIZE(orion5x_xor0_resources), + .resource = orion5x_xor0_resources, + .dev = { + .dma_mask = &orion5x_xor_dmamask, + .coherent_dma_mask = DMA_64BIT_MASK, + .platform_data = (void *)&orion5x_xor0_data, + }, +}; + +static struct resource orion5x_xor1_resources[] = { + [0] = { + .start = IRQ_ORION5X_XOR1, + .end = IRQ_ORION5X_XOR1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct mv_xor_platform_data orion5x_xor1_data = { + .shared = &orion5x_xor_shared, + .hw_id = 1, + .pool_size = PAGE_SIZE, +}; + +static struct platform_device orion5x_xor1_channel = { + .name = MV_XOR_NAME, + .id = 1, + .num_resources = ARRAY_SIZE(orion5x_xor1_resources), + .resource = orion5x_xor1_resources, + .dev = { + .dma_mask = &orion5x_xor_dmamask, + .coherent_dma_mask = DMA_64BIT_MASK, + .platform_data = (void *)&orion5x_xor1_data, + }, +}; + +void __init orion5x_xor_init(void) +{ + platform_device_register(&orion5x_xor_shared); + + /* + * two engines can't do memset simultaneously, this limitation + * satisfied by removing memset support from one of the engines. + */ + dma_cap_set(DMA_MEMCPY, orion5x_xor0_data.cap_mask); + dma_cap_set(DMA_XOR, orion5x_xor0_data.cap_mask); + platform_device_register(&orion5x_xor0_channel); + + dma_cap_set(DMA_MEMCPY, orion5x_xor1_data.cap_mask); + dma_cap_set(DMA_MEMSET, orion5x_xor1_data.cap_mask); + dma_cap_set(DMA_XOR, orion5x_xor1_data.cap_mask); + platform_device_register(&orion5x_xor1_channel); +} + + /***************************************************************************** * Time handling ****************************************************************************/ diff --git a/arch/arm/mach-orion5x/common.h b/arch/arm/mach-orion5x/common.h index f72cf0e7754..e75bd7004b9 100644 --- a/arch/arm/mach-orion5x/common.h +++ b/arch/arm/mach-orion5x/common.h @@ -32,6 +32,7 @@ void orion5x_i2c_init(void); void orion5x_sata_init(struct mv_sata_platform_data *sata_data); void orion5x_uart0_init(void); void orion5x_uart1_init(void); +void orion5x_xor_init(void); /* * PCIe/PCI functions. diff --git a/arch/arm/mach-orion5x/include/mach/orion5x.h b/arch/arm/mach-orion5x/include/mach/orion5x.h index 77978dbd5a9..61eb74a8886 100644 --- a/arch/arm/mach-orion5x/include/mach/orion5x.h +++ b/arch/arm/mach-orion5x/include/mach/orion5x.h @@ -106,6 +106,10 @@ #define ORION5X_USB0_VIRT_BASE (ORION5X_REGS_VIRT_BASE | 0x50000) #define ORION5X_USB0_REG(x) (ORION5X_USB0_VIRT_BASE | (x)) +#define ORION5X_XOR_PHYS_BASE (ORION5X_REGS_PHYS_BASE | 0x60900) +#define ORION5X_XOR_VIRT_BASE (ORION5X_REGS_VIRT_BASE | 0x60900) +#define ORION5X_XOR_REG(x) (ORION5X_XOR_VIRT_BASE | (x)) + #define ORION5X_ETH_PHYS_BASE (ORION5X_REGS_PHYS_BASE | 0x70000) #define ORION5X_ETH_VIRT_BASE (ORION5X_REGS_VIRT_BASE | 0x70000) #define ORION5X_ETH_REG(x) (ORION5X_ETH_VIRT_BASE | (x)) diff --git a/arch/arm/mach-orion5x/kurobox_pro-setup.c b/arch/arm/mach-orion5x/kurobox_pro-setup.c index 45dfc9f99d8..cb72f1bb9cb 100644 --- a/arch/arm/mach-orion5x/kurobox_pro-setup.c +++ b/arch/arm/mach-orion5x/kurobox_pro-setup.c @@ -356,6 +356,7 @@ static void __init kurobox_pro_init(void) orion5x_sata_init(&kurobox_pro_sata_data); orion5x_uart0_init(); orion5x_uart1_init(); + orion5x_xor_init(); orion5x_setup_dev_boot_win(KUROBOX_PRO_NOR_BOOT_BASE, KUROBOX_PRO_NOR_BOOT_SIZE); diff --git a/arch/arm/mach-orion5x/mss2-setup.c b/arch/arm/mach-orion5x/mss2-setup.c index 4403cc963d6..53ff1893b88 100644 --- a/arch/arm/mach-orion5x/mss2-setup.c +++ b/arch/arm/mach-orion5x/mss2-setup.c @@ -239,6 +239,7 @@ static void __init mss2_init(void) orion5x_i2c_init(); orion5x_sata_init(&mss2_sata_data); orion5x_uart0_init(); + orion5x_xor_init(); orion5x_setup_dev_boot_win(MSS2_NOR_BOOT_BASE, MSS2_NOR_BOOT_SIZE); platform_device_register(&mss2_nor_flash); diff --git a/arch/arm/mach-orion5x/mv2120-setup.c b/arch/arm/mach-orion5x/mv2120-setup.c index 67b2c0df615..978d4d59939 100644 --- a/arch/arm/mach-orion5x/mv2120-setup.c +++ b/arch/arm/mach-orion5x/mv2120-setup.c @@ -203,6 +203,7 @@ static void __init mv2120_init(void) orion5x_i2c_init(); orion5x_sata_init(&mv2120_sata_data); orion5x_uart0_init(); + orion5x_xor_init(); orion5x_setup_dev_boot_win(MV2120_NOR_BOOT_BASE, MV2120_NOR_BOOT_SIZE); platform_device_register(&mv2120_nor_flash); diff --git a/arch/arm/mach-orion5x/rd88f5182-setup.c b/arch/arm/mach-orion5x/rd88f5182-setup.c index 8771cb76f0d..4c3bcd76ac8 100644 --- a/arch/arm/mach-orion5x/rd88f5182-setup.c +++ b/arch/arm/mach-orion5x/rd88f5182-setup.c @@ -292,6 +292,7 @@ static void __init rd88f5182_init(void) orion5x_i2c_init(); orion5x_sata_init(&rd88f5182_sata_data); orion5x_uart0_init(); + orion5x_xor_init(); orion5x_setup_dev_boot_win(RD88F5182_NOR_BOOT_BASE, RD88F5182_NOR_BOOT_SIZE); diff --git a/arch/arm/mach-orion5x/ts209-setup.c b/arch/arm/mach-orion5x/ts209-setup.c index 1bb7de8a262..dd657163cd8 100644 --- a/arch/arm/mach-orion5x/ts209-setup.c +++ b/arch/arm/mach-orion5x/ts209-setup.c @@ -296,6 +296,7 @@ static void __init qnap_ts209_init(void) orion5x_i2c_init(); orion5x_sata_init(&qnap_ts209_sata_data); orion5x_uart0_init(); + orion5x_xor_init(); orion5x_setup_dev_boot_win(QNAP_TS209_NOR_BOOT_BASE, QNAP_TS209_NOR_BOOT_SIZE); diff --git a/arch/arm/mach-orion5x/ts78xx-setup.c b/arch/arm/mach-orion5x/ts78xx-setup.c index 014916a28fd..ae0a5dccd2a 100644 --- a/arch/arm/mach-orion5x/ts78xx-setup.c +++ b/arch/arm/mach-orion5x/ts78xx-setup.c @@ -256,6 +256,7 @@ static void __init ts78xx_init(void) orion5x_sata_init(&ts78xx_sata_data); orion5x_uart0_init(); orion5x_uart1_init(); + orion5x_xor_init(); orion5x_setup_dev_boot_win(TS78XX_NOR_BOOT_BASE, TS78XX_NOR_BOOT_SIZE); -- GitLab From 09c0ed2e6eb87613b2670c15ba771ac671db19d9 Mon Sep 17 00:00:00 2001 From: Saeed Bishara Date: Mon, 23 Jun 2008 04:26:07 -1100 Subject: [PATCH 083/750] [ARM] Kirkwood: Instantiate mv_xor driver Signed-off-by: Saeed Bishara Signed-off-by: Lennert Buytenhek --- arch/arm/mach-kirkwood/common.c | 207 ++++++++++++++++++ arch/arm/mach-kirkwood/common.h | 2 + .../arm/mach-kirkwood/include/mach/kirkwood.h | 9 + arch/arm/mach-kirkwood/rd88f6192-nas-setup.c | 2 + 4 files changed, 220 insertions(+) diff --git a/arch/arm/mach-kirkwood/common.c b/arch/arm/mach-kirkwood/common.c index 02edd0dccc4..693dc32b606 100644 --- a/arch/arm/mach-kirkwood/common.c +++ b/arch/arm/mach-kirkwood/common.c @@ -22,6 +22,7 @@ #include #include #include +#include #include #include #include "common.h" @@ -283,6 +284,212 @@ void __init kirkwood_uart1_init(void) } +/***************************************************************************** + * XOR + ****************************************************************************/ +static struct mv_xor_platform_shared_data kirkwood_xor_shared_data = { + .dram = &kirkwood_mbus_dram_info, +}; + +static u64 kirkwood_xor_dmamask = DMA_32BIT_MASK; + + +/***************************************************************************** + * XOR0 + ****************************************************************************/ +static struct resource kirkwood_xor0_shared_resources[] = { + { + .name = "xor 0 low", + .start = XOR0_PHYS_BASE, + .end = XOR0_PHYS_BASE + 0xff, + .flags = IORESOURCE_MEM, + }, { + .name = "xor 0 high", + .start = XOR0_HIGH_PHYS_BASE, + .end = XOR0_HIGH_PHYS_BASE + 0xff, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device kirkwood_xor0_shared = { + .name = MV_XOR_SHARED_NAME, + .id = 0, + .dev = { + .platform_data = &kirkwood_xor_shared_data, + }, + .num_resources = ARRAY_SIZE(kirkwood_xor0_shared_resources), + .resource = kirkwood_xor0_shared_resources, +}; + +static struct resource kirkwood_xor00_resources[] = { + [0] = { + .start = IRQ_KIRKWOOD_XOR_00, + .end = IRQ_KIRKWOOD_XOR_00, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct mv_xor_platform_data kirkwood_xor00_data = { + .shared = &kirkwood_xor0_shared, + .hw_id = 0, + .pool_size = PAGE_SIZE, +}; + +static struct platform_device kirkwood_xor00_channel = { + .name = MV_XOR_NAME, + .id = 0, + .num_resources = ARRAY_SIZE(kirkwood_xor00_resources), + .resource = kirkwood_xor00_resources, + .dev = { + .dma_mask = &kirkwood_xor_dmamask, + .coherent_dma_mask = DMA_64BIT_MASK, + .platform_data = (void *)&kirkwood_xor00_data, + }, +}; + +static struct resource kirkwood_xor01_resources[] = { + [0] = { + .start = IRQ_KIRKWOOD_XOR_01, + .end = IRQ_KIRKWOOD_XOR_01, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct mv_xor_platform_data kirkwood_xor01_data = { + .shared = &kirkwood_xor0_shared, + .hw_id = 1, + .pool_size = PAGE_SIZE, +}; + +static struct platform_device kirkwood_xor01_channel = { + .name = MV_XOR_NAME, + .id = 1, + .num_resources = ARRAY_SIZE(kirkwood_xor01_resources), + .resource = kirkwood_xor01_resources, + .dev = { + .dma_mask = &kirkwood_xor_dmamask, + .coherent_dma_mask = DMA_64BIT_MASK, + .platform_data = (void *)&kirkwood_xor01_data, + }, +}; + +void __init kirkwood_xor0_init(void) +{ + platform_device_register(&kirkwood_xor0_shared); + + /* + * two engines can't do memset simultaneously, this limitation + * satisfied by removing memset support from one of the engines. + */ + dma_cap_set(DMA_MEMCPY, kirkwood_xor00_data.cap_mask); + dma_cap_set(DMA_XOR, kirkwood_xor00_data.cap_mask); + platform_device_register(&kirkwood_xor00_channel); + + dma_cap_set(DMA_MEMCPY, kirkwood_xor01_data.cap_mask); + dma_cap_set(DMA_MEMSET, kirkwood_xor01_data.cap_mask); + dma_cap_set(DMA_XOR, kirkwood_xor01_data.cap_mask); + platform_device_register(&kirkwood_xor01_channel); +} + + +/***************************************************************************** + * XOR1 + ****************************************************************************/ +static struct resource kirkwood_xor1_shared_resources[] = { + { + .name = "xor 1 low", + .start = XOR1_PHYS_BASE, + .end = XOR1_PHYS_BASE + 0xff, + .flags = IORESOURCE_MEM, + }, { + .name = "xor 1 high", + .start = XOR1_HIGH_PHYS_BASE, + .end = XOR1_HIGH_PHYS_BASE + 0xff, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device kirkwood_xor1_shared = { + .name = MV_XOR_SHARED_NAME, + .id = 1, + .dev = { + .platform_data = &kirkwood_xor_shared_data, + }, + .num_resources = ARRAY_SIZE(kirkwood_xor1_shared_resources), + .resource = kirkwood_xor1_shared_resources, +}; + +static struct resource kirkwood_xor10_resources[] = { + [0] = { + .start = IRQ_KIRKWOOD_XOR_10, + .end = IRQ_KIRKWOOD_XOR_10, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct mv_xor_platform_data kirkwood_xor10_data = { + .shared = &kirkwood_xor1_shared, + .hw_id = 0, + .pool_size = PAGE_SIZE, +}; + +static struct platform_device kirkwood_xor10_channel = { + .name = MV_XOR_NAME, + .id = 2, + .num_resources = ARRAY_SIZE(kirkwood_xor10_resources), + .resource = kirkwood_xor10_resources, + .dev = { + .dma_mask = &kirkwood_xor_dmamask, + .coherent_dma_mask = DMA_64BIT_MASK, + .platform_data = (void *)&kirkwood_xor10_data, + }, +}; + +static struct resource kirkwood_xor11_resources[] = { + [0] = { + .start = IRQ_KIRKWOOD_XOR_11, + .end = IRQ_KIRKWOOD_XOR_11, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct mv_xor_platform_data kirkwood_xor11_data = { + .shared = &kirkwood_xor1_shared, + .hw_id = 1, + .pool_size = PAGE_SIZE, +}; + +static struct platform_device kirkwood_xor11_channel = { + .name = MV_XOR_NAME, + .id = 3, + .num_resources = ARRAY_SIZE(kirkwood_xor11_resources), + .resource = kirkwood_xor11_resources, + .dev = { + .dma_mask = &kirkwood_xor_dmamask, + .coherent_dma_mask = DMA_64BIT_MASK, + .platform_data = (void *)&kirkwood_xor11_data, + }, +}; + +void __init kirkwood_xor1_init(void) +{ + platform_device_register(&kirkwood_xor1_shared); + + /* + * two engines can't do memset simultaneously, this limitation + * satisfied by removing memset support from one of the engines. + */ + dma_cap_set(DMA_MEMCPY, kirkwood_xor10_data.cap_mask); + dma_cap_set(DMA_XOR, kirkwood_xor10_data.cap_mask); + platform_device_register(&kirkwood_xor10_channel); + + dma_cap_set(DMA_MEMCPY, kirkwood_xor11_data.cap_mask); + dma_cap_set(DMA_MEMSET, kirkwood_xor11_data.cap_mask); + dma_cap_set(DMA_XOR, kirkwood_xor11_data.cap_mask); + platform_device_register(&kirkwood_xor11_channel); +} + + /***************************************************************************** * Time handling ****************************************************************************/ diff --git a/arch/arm/mach-kirkwood/common.h b/arch/arm/mach-kirkwood/common.h index 5dee2f6b40a..6f94cda81de 100644 --- a/arch/arm/mach-kirkwood/common.h +++ b/arch/arm/mach-kirkwood/common.h @@ -35,6 +35,8 @@ void kirkwood_rtc_init(void); void kirkwood_sata_init(struct mv_sata_platform_data *sata_data); void kirkwood_uart0_init(void); void kirkwood_uart1_init(void); +void kirkwood_xor0_init(void); +void kirkwood_xor1_init(void); extern struct sys_timer kirkwood_timer; diff --git a/arch/arm/mach-kirkwood/include/mach/kirkwood.h b/arch/arm/mach-kirkwood/include/mach/kirkwood.h index d1336b41f0f..5c69992295e 100644 --- a/arch/arm/mach-kirkwood/include/mach/kirkwood.h +++ b/arch/arm/mach-kirkwood/include/mach/kirkwood.h @@ -88,6 +88,15 @@ #define USB_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x50000) +#define XOR0_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x60800) +#define XOR0_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x60800) +#define XOR1_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x60900) +#define XOR1_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x60900) +#define XOR0_HIGH_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x60A00) +#define XOR0_HIGH_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x60A00) +#define XOR1_HIGH_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x60B00) +#define XOR1_HIGH_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x60B00) + #define GE00_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x70000) #define GE01_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x74000) diff --git a/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c b/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c index 182230a5d19..062c3216b8a 100644 --- a/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c +++ b/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c @@ -46,6 +46,8 @@ static void __init rd88f6192_init(void) kirkwood_rtc_init(); kirkwood_sata_init(&rd88f6192_sata_data); kirkwood_uart0_init(); + kirkwood_xor0_init(); + kirkwood_xor1_init(); } static int __init rd88f6192_pci_init(void) -- GitLab From 60296c71f6c5063e3c1f1d2619ca0b60940162e7 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Tue, 5 Aug 2008 01:56:13 +0200 Subject: [PATCH 084/750] [ARM] prevent crashing when too much RAM installed This patch will truncate and/or ignore memory banks if their kernel direct mappings would (partially) overlap with the vmalloc area or the mappings between the vmalloc area and the address space top, to prevent crashing during early boot if there happens to be more RAM installed than we are expecting. Since the start of the vmalloc area is not at a fixed address (but the vmalloc end address is, via the per-platform VMALLOC_END define), a default area of 128M is reserved for vmalloc mappings, which can be shrunk or enlarged by passing an appropriate vmalloc= command line option as it is done on x86. On a board with a 3:1 user:kernel split, VMALLOC_END at 0xfe000000, two 512M RAM banks and vmalloc=128M (the default), this patch gives: Truncating RAM at 20000000-3fffffff to -35ffffff (vmalloc region overlap). Memory: 512MB 352MB = 864MB total On a board with a 3:1 user:kernel split, VMALLOC_END at 0xfe800000, two 256M RAM banks and vmalloc=768M, this patch gives: Truncating RAM at 00000000-0fffffff to -0e7fffff (vmalloc region overlap). Ignoring RAM at 10000000-1fffffff (vmalloc region overlap). Signed-off-by: Lennert Buytenhek Tested-by: Riku Voipio --- arch/arm/include/asm/memory.h | 8 ++++++ arch/arm/kernel/setup.c | 13 +++++++++ arch/arm/mm/mmu.c | 50 +++++++++++++++++++++++++++++++++++ 3 files changed, 71 insertions(+) diff --git a/arch/arm/include/asm/memory.h b/arch/arm/include/asm/memory.h index 1e070a2b561..7bcd69a9a88 100644 --- a/arch/arm/include/asm/memory.h +++ b/arch/arm/include/asm/memory.h @@ -149,6 +149,14 @@ #define arch_adjust_zones(node,size,holes) do { } while (0) #endif +/* + * Amount of memory reserved for the vmalloc() area, and minimum + * address for vmalloc mappings. + */ +extern unsigned long vmalloc_reserve; + +#define VMALLOC_MIN (void *)(VMALLOC_END - vmalloc_reserve) + /* * PFNs are used to describe any physical page; this means * PFN 0 == physical address 0. diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c index 38f0e7940a1..2ca7038b67a 100644 --- a/arch/arm/kernel/setup.c +++ b/arch/arm/kernel/setup.c @@ -81,6 +81,8 @@ EXPORT_SYMBOL(system_serial_high); unsigned int elf_hwcap; EXPORT_SYMBOL(elf_hwcap); +unsigned long __initdata vmalloc_reserve = 128 << 20; + #ifdef MULTI_CPU struct processor processor; @@ -500,6 +502,17 @@ static void __init early_mem(char **p) } __early_param("mem=", early_mem); +/* + * vmalloc=size forces the vmalloc area to be exactly 'size' + * bytes. This can be used to increase (or decrease) the vmalloc + * area - the default is 128m. + */ +static void __init early_vmalloc(char **arg) +{ + vmalloc_reserve = memparse(*arg, arg); +} +__early_param("vmalloc=", early_vmalloc); + /* * Initial parsing of the command line. */ diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c index 2d6d682c206..25d9a11eb61 100644 --- a/arch/arm/mm/mmu.c +++ b/arch/arm/mm/mmu.c @@ -568,6 +568,55 @@ void __init iotable_init(struct map_desc *io_desc, int nr) create_mapping(io_desc + i); } +static int __init check_membank_valid(struct membank *mb) +{ + /* + * Check whether this memory region has non-zero size. + */ + if (mb->size == 0) + return 0; + + /* + * Check whether this memory region would entirely overlap + * the vmalloc area. + */ + if (phys_to_virt(mb->start) >= VMALLOC_MIN) { + printk(KERN_NOTICE "Ignoring RAM at %.8lx-%.8lx " + "(vmalloc region overlap).\n", + mb->start, mb->start + mb->size - 1); + return 0; + } + + /* + * Check whether this memory region would partially overlap + * the vmalloc area. + */ + if (phys_to_virt(mb->start + mb->size) < phys_to_virt(mb->start) || + phys_to_virt(mb->start + mb->size) > VMALLOC_MIN) { + unsigned long newsize = VMALLOC_MIN - phys_to_virt(mb->start); + + printk(KERN_NOTICE "Truncating RAM at %.8lx-%.8lx " + "to -%.8lx (vmalloc region overlap).\n", + mb->start, mb->start + mb->size - 1, + mb->start + newsize - 1); + mb->size = newsize; + } + + return 1; +} + +static void __init sanity_check_meminfo(struct meminfo *mi) +{ + int i; + int j; + + for (i = 0, j = 0; i < mi->nr_banks; i++) { + if (check_membank_valid(&mi->bank[i])) + mi->bank[j++] = mi->bank[i]; + } + mi->nr_banks = j; +} + static inline void prepare_page_table(struct meminfo *mi) { unsigned long addr; @@ -753,6 +802,7 @@ void __init paging_init(struct meminfo *mi, struct machine_desc *mdesc) void *zero_page; build_mem_type_table(); + sanity_check_meminfo(mi); prepare_page_table(mi); bootmem_init(mi); devicemaps_init(mdesc); -- GitLab From 18365d181fe7fee8b52cd12482200d3a4c48d05e Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Sat, 9 Aug 2008 15:38:18 +0200 Subject: [PATCH 085/750] [ARM] Kirkwood: instantiate the orion_spi driver in the platform code Signed-off-by: Lennert Buytenhek --- arch/arm/mach-kirkwood/common.c | 32 ++++++++++++++++++++ arch/arm/mach-kirkwood/common.h | 1 + arch/arm/mach-kirkwood/rd88f6192-nas-setup.c | 21 +++++++++++++ 3 files changed, 54 insertions(+) diff --git a/arch/arm/mach-kirkwood/common.c b/arch/arm/mach-kirkwood/common.c index 693dc32b606..189f16f3619 100644 --- a/arch/arm/mach-kirkwood/common.c +++ b/arch/arm/mach-kirkwood/common.c @@ -15,6 +15,7 @@ #include #include #include +#include #include #include #include @@ -196,6 +197,37 @@ void __init kirkwood_sata_init(struct mv_sata_platform_data *sata_data) } +/***************************************************************************** + * SPI + ****************************************************************************/ +static struct orion_spi_info kirkwood_spi_plat_data = { + .tclk = KIRKWOOD_TCLK, +}; + +static struct resource kirkwood_spi_resources[] = { + { + .start = SPI_PHYS_BASE, + .end = SPI_PHYS_BASE + SZ_512 - 1, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device kirkwood_spi = { + .name = "orion_spi", + .id = 0, + .resource = kirkwood_spi_resources, + .dev = { + .platform_data = &kirkwood_spi_plat_data, + }, + .num_resources = ARRAY_SIZE(kirkwood_spi_resources), +}; + +void __init kirkwood_spi_init() +{ + platform_device_register(&kirkwood_spi); +} + + /***************************************************************************** * UART0 ****************************************************************************/ diff --git a/arch/arm/mach-kirkwood/common.h b/arch/arm/mach-kirkwood/common.h index 6f94cda81de..69cd113af03 100644 --- a/arch/arm/mach-kirkwood/common.h +++ b/arch/arm/mach-kirkwood/common.h @@ -33,6 +33,7 @@ void kirkwood_ge00_init(struct mv643xx_eth_platform_data *eth_data); void kirkwood_pcie_init(void); void kirkwood_rtc_init(void); void kirkwood_sata_init(struct mv_sata_platform_data *sata_data); +void kirkwood_spi_init(void); void kirkwood_uart0_init(void); void kirkwood_uart1_init(void); void kirkwood_xor0_init(void); diff --git a/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c b/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c index 062c3216b8a..a3012d44597 100644 --- a/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c +++ b/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c @@ -18,6 +18,9 @@ #include #include #include +#include +#include +#include #include #include #include @@ -34,6 +37,21 @@ static struct mv_sata_platform_data rd88f6192_sata_data = { .n_ports = 2, }; +static const struct flash_platform_data rd88F6192_spi_slave_data = { + .type = "m25p128", +}; + +static struct spi_board_info __initdata rd88F6192_spi_slave_info[] = { + { + .modalias = "m25p80", + .platform_data = &rd88F6192_spi_slave_data, + .irq = -1, + .max_speed_hz = 20000000, + .bus_num = 0, + .chip_select = 0, + }, +}; + static void __init rd88f6192_init(void) { /* @@ -45,6 +63,9 @@ static void __init rd88f6192_init(void) kirkwood_ge00_init(&rd88f6192_ge00_data); kirkwood_rtc_init(); kirkwood_sata_init(&rd88f6192_sata_data); + spi_register_board_info(rd88F6192_spi_slave_info, + ARRAY_SIZE(rd88F6192_spi_slave_info)); + kirkwood_spi_init(); kirkwood_uart0_init(); kirkwood_xor0_init(); kirkwood_xor1_init(); -- GitLab From b6b7922fbda63040946cac8251d5618ee7880e8a Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Sat, 9 Aug 2008 16:25:26 -0700 Subject: [PATCH 086/750] sparc64: Don't MAGIC_SYSRQ ifdef smp_fetch_global_regs and support code. Based upon a report and initial patch by Friedrich Oslage. The intention is to provide this facility for __trigger_all_cpu_backtrace even if MAGIC_SYSRQ is not set. The only part that should have MAGIC_SYSRQ ifdef protection is the sparc_globalreg_op sysrq regitration and immediate code. Signed-off-by: David S. Miller --- arch/sparc64/kernel/smp.c | 4 ---- arch/sparc64/mm/ultra.S | 2 -- 2 files changed, 6 deletions(-) diff --git a/arch/sparc64/kernel/smp.c b/arch/sparc64/kernel/smp.c index 27b81775a4d..743ccad61c6 100644 --- a/arch/sparc64/kernel/smp.c +++ b/arch/sparc64/kernel/smp.c @@ -858,9 +858,7 @@ void smp_tsb_sync(struct mm_struct *mm) extern unsigned long xcall_flush_tlb_mm; extern unsigned long xcall_flush_tlb_pending; extern unsigned long xcall_flush_tlb_kernel_range; -#ifdef CONFIG_MAGIC_SYSRQ extern unsigned long xcall_fetch_glob_regs; -#endif extern unsigned long xcall_receive_signal; extern unsigned long xcall_new_mmu_context_version; #ifdef CONFIG_KGDB @@ -1005,12 +1003,10 @@ void kgdb_roundup_cpus(unsigned long flags) } #endif -#ifdef CONFIG_MAGIC_SYSRQ void smp_fetch_global_regs(void) { smp_cross_call(&xcall_fetch_glob_regs, 0, 0, 0); } -#endif /* We know that the window frames of the user have been flushed * to the stack before we get here because all callers of us diff --git a/arch/sparc64/mm/ultra.S b/arch/sparc64/mm/ultra.S index ff1dc44d363..86773e89dc1 100644 --- a/arch/sparc64/mm/ultra.S +++ b/arch/sparc64/mm/ultra.S @@ -480,7 +480,6 @@ xcall_sync_tick: b rtrap_xcall ldx [%sp + PTREGS_OFF + PT_V9_TSTATE], %l1 -#ifdef CONFIG_MAGIC_SYSRQ .globl xcall_fetch_glob_regs xcall_fetch_glob_regs: sethi %hi(global_reg_snapshot), %g1 @@ -511,7 +510,6 @@ xcall_fetch_glob_regs: membar #StoreStore stx %g3, [%g1 + GR_SNAP_THREAD] retry -#endif /* CONFIG_MAGIC_SYSRQ */ #ifdef DCACHE_ALIASING_POSSIBLE .align 32 -- GitLab From 98ed7d4b1a4eebc1ac25929b6968673bef4d54c3 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 10 Aug 2008 12:10:49 +0100 Subject: [PATCH 087/750] [ARM] dma-mapping: improve type-safeness of DMA translations OMAP at least gets the return type(s) for the DMA translation functions wrong, which can lead to subtle errors. Avoid this by moving the DMA translation functions to asm/dma-mapping.h, and converting them to inline functions. Fix the OMAP DMA translation macros to use the correct argument and result types. Also, remove the unnecessary casts in dmabounce.c. Signed-off-by: Russell King --- arch/arm/common/dmabounce.c | 18 ++++----- arch/arm/include/asm/dma-mapping.h | 51 ++++++++++++++++++++---- arch/arm/include/asm/memory.h | 14 ------- arch/arm/plat-omap/include/mach/memory.h | 15 +++---- 4 files changed, 61 insertions(+), 37 deletions(-) diff --git a/arch/arm/common/dmabounce.c b/arch/arm/common/dmabounce.c index 69130f36590..1ea6482cdf6 100644 --- a/arch/arm/common/dmabounce.c +++ b/arch/arm/common/dmabounce.c @@ -246,9 +246,9 @@ map_single(struct device *dev, void *ptr, size_t size, } dev_dbg(dev, - "%s: unsafe buffer %p (phy=%p) mapped to %p (phy=%p)\n", - __func__, buf->ptr, (void *) virt_to_dma(dev, buf->ptr), - buf->safe, (void *) buf->safe_dma_addr); + "%s: unsafe buffer %p (dma=%#x) mapped to %p (dma=%#x)\n", + __func__, buf->ptr, virt_to_dma(dev, buf->ptr), + buf->safe, buf->safe_dma_addr); if ((dir == DMA_TO_DEVICE) || (dir == DMA_BIDIRECTIONAL)) { @@ -292,9 +292,9 @@ unmap_single(struct device *dev, dma_addr_t dma_addr, size_t size, BUG_ON(buf->size != size); dev_dbg(dev, - "%s: unsafe buffer %p (phy=%p) mapped to %p (phy=%p)\n", - __func__, buf->ptr, (void *) virt_to_dma(dev, buf->ptr), - buf->safe, (void *) buf->safe_dma_addr); + "%s: unsafe buffer %p (dma=%#x) mapped to %p (dma=%#x)\n", + __func__, buf->ptr, virt_to_dma(dev, buf->ptr), + buf->safe, buf->safe_dma_addr); DO_STATS ( device_info->bounce_count++ ); @@ -355,9 +355,9 @@ sync_single(struct device *dev, dma_addr_t dma_addr, size_t size, */ dev_dbg(dev, - "%s: unsafe buffer %p (phy=%p) mapped to %p (phy=%p)\n", - __func__, buf->ptr, (void *) virt_to_dma(dev, buf->ptr), - buf->safe, (void *) buf->safe_dma_addr); + "%s: unsafe buffer %p (dma=%#x) mapped to %p (dma=%#x)\n", + __func__, buf->ptr, virt_to_dma(dev, buf->ptr), + buf->safe, buf->safe_dma_addr); DO_STATS ( device_info->bounce_count++ ); diff --git a/arch/arm/include/asm/dma-mapping.h b/arch/arm/include/asm/dma-mapping.h index 45329fca1b6..6f45959fe2c 100644 --- a/arch/arm/include/asm/dma-mapping.h +++ b/arch/arm/include/asm/dma-mapping.h @@ -3,11 +3,48 @@ #ifdef __KERNEL__ -#include /* need struct page */ - +#include #include #include +#include + +/* + * page_to_dma/dma_to_virt/virt_to_dma are architecture private functions + * used internally by the DMA-mapping API to provide DMA addresses. They + * must not be used by drivers. + */ +#ifndef __arch_page_to_dma +static inline dma_addr_t page_to_dma(struct device *dev, struct page *page) +{ + return (dma_addr_t)__virt_to_bus((unsigned long)page_address(page)); +} + +static inline void *dma_to_virt(struct device *dev, dma_addr_t addr) +{ + return (void *)__bus_to_virt(addr); +} + +static inline dma_addr_t virt_to_dma(struct device *dev, void *addr) +{ + return (dma_addr_t)__virt_to_bus((unsigned long)(addr)); +} +#else +static inline dma_addr_t page_to_dma(struct device *dev, struct page *page) +{ + return __arch_page_to_dma(dev, page); +} + +static inline void *dma_to_virt(struct device *dev, dma_addr_t addr) +{ + return __arch_dma_to_virt(dev, addr); +} + +static inline dma_addr_t virt_to_dma(struct device *dev, void *addr) +{ + return __arch_virt_to_dma(dev, addr); +} +#endif /* * DMA-consistent mapping functions. These allocate/free a region of @@ -169,7 +206,7 @@ dma_map_single(struct device *dev, void *cpu_addr, size_t size, if (!arch_is_coherent()) dma_cache_maint(cpu_addr, size, dir); - return virt_to_dma(dev, (unsigned long)cpu_addr); + return virt_to_dma(dev, cpu_addr); } #else extern dma_addr_t dma_map_single(struct device *,void *, size_t, enum dma_data_direction); @@ -195,7 +232,7 @@ dma_map_page(struct device *dev, struct page *page, unsigned long offset, size_t size, enum dma_data_direction dir) { - return dma_map_single(dev, page_address(page) + offset, size, (int)dir); + return dma_map_single(dev, page_address(page) + offset, size, dir); } /** @@ -241,7 +278,7 @@ static inline void dma_unmap_page(struct device *dev, dma_addr_t handle, size_t size, enum dma_data_direction dir) { - dma_unmap_single(dev, handle, size, (int)dir); + dma_unmap_single(dev, handle, size, dir); } /** @@ -336,7 +373,7 @@ dma_sync_single_for_cpu(struct device *dev, dma_addr_t handle, size_t size, enum dma_data_direction dir) { if (!arch_is_coherent()) - dma_cache_maint((void *)dma_to_virt(dev, handle), size, dir); + dma_cache_maint(dma_to_virt(dev, handle), size, dir); } static inline void @@ -344,7 +381,7 @@ dma_sync_single_for_device(struct device *dev, dma_addr_t handle, size_t size, enum dma_data_direction dir) { if (!arch_is_coherent()) - dma_cache_maint((void *)dma_to_virt(dev, handle), size, dir); + dma_cache_maint(dma_to_virt(dev, handle), size, dir); } #else extern void dma_sync_single_for_cpu(struct device*, dma_addr_t, size_t, enum dma_data_direction); diff --git a/arch/arm/include/asm/memory.h b/arch/arm/include/asm/memory.h index 7bcd69a9a88..bf7c737c922 100644 --- a/arch/arm/include/asm/memory.h +++ b/arch/arm/include/asm/memory.h @@ -313,20 +313,6 @@ static inline __deprecated void *bus_to_virt(unsigned long x) */ #define page_to_phys(page) (page_to_pfn(page) << PAGE_SHIFT) -/* - * Optional device DMA address remapping. Do _not_ use directly! - * We should really eliminate virt_to_bus() here - it's deprecated. - */ -#ifndef __arch_page_to_dma -#define page_to_dma(dev, page) ((dma_addr_t)__virt_to_bus((unsigned long)page_address(page))) -#define dma_to_virt(dev, addr) ((void *)__bus_to_virt(addr)) -#define virt_to_dma(dev, addr) ((dma_addr_t)__virt_to_bus((unsigned long)(addr))) -#else -#define page_to_dma(dev, page) (__arch_page_to_dma(dev, page)) -#define dma_to_virt(dev, addr) (__arch_dma_to_virt(dev, addr)) -#define virt_to_dma(dev, addr) (__arch_virt_to_dma(dev, addr)) -#endif - /* * Optional coherency support. Currently used only by selected * Intel XSC3-based systems. diff --git a/arch/arm/plat-omap/include/mach/memory.h b/arch/arm/plat-omap/include/mach/memory.h index 037486c5f4a..a325caf80d0 100644 --- a/arch/arm/plat-omap/include/mach/memory.h +++ b/arch/arm/plat-omap/include/mach/memory.h @@ -76,13 +76,14 @@ (dma_addr_t)virt_to_lbus(page_address(page)) : \ (dma_addr_t)__virt_to_bus(page_address(page));}) -#define __arch_dma_to_virt(dev, addr) ({is_lbus_device(dev) ? \ - lbus_to_virt(addr) : \ - __bus_to_virt(addr);}) - -#define __arch_virt_to_dma(dev, addr) ({is_lbus_device(dev) ? \ - virt_to_lbus(addr) : \ - __virt_to_bus(addr);}) +#define __arch_dma_to_virt(dev, addr) ({ (void *) (is_lbus_device(dev) ? \ + lbus_to_virt(addr) : \ + __bus_to_virt(addr)); }) + +#define __arch_virt_to_dma(dev, addr) ({ unsigned long __addr = (unsigned long)(addr); \ + (dma_addr_t) (is_lbus_device(dev) ? \ + virt_to_lbus(__addr) : \ + __virt_to_bus(__addr)); }) #endif /* CONFIG_ARCH_OMAP15XX */ -- GitLab From 9dd428680573d7867ee5e40fa3f059a98301d416 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 10 Aug 2008 12:18:26 +0100 Subject: [PATCH 088/750] [ARM] dma-mapping: provide sync_range APIs Convert the existing dma_sync_single_for_* APIs to the new range based APIs, and make the dma_sync_single_for_* API a superset of it. Signed-off-by: Russell King --- arch/arm/common/dmabounce.c | 38 +++++++++++++++-------------- arch/arm/include/asm/dma-mapping.h | 39 +++++++++++++++++++++--------- 2 files changed, 48 insertions(+), 29 deletions(-) diff --git a/arch/arm/common/dmabounce.c b/arch/arm/common/dmabounce.c index 1ea6482cdf6..aecc6c3f908 100644 --- a/arch/arm/common/dmabounce.c +++ b/arch/arm/common/dmabounce.c @@ -321,9 +321,8 @@ unmap_single(struct device *dev, dma_addr_t dma_addr, size_t size, } } -static inline void -sync_single(struct device *dev, dma_addr_t dma_addr, size_t size, - enum dma_data_direction dir) +static int sync_single(struct device *dev, dma_addr_t dma_addr, size_t size, + enum dma_data_direction dir) { struct dmabounce_device_info *device_info = dev->archdata.dmabounce; struct safe_buffer *buf = NULL; @@ -383,8 +382,9 @@ sync_single(struct device *dev, dma_addr_t dma_addr, size_t size, * No need to sync the safe buffer - it was allocated * via the coherent allocators. */ + return 0; } else { - dma_cache_maint(dma_to_virt(dev, dma_addr), size, dir); + return 1; } } @@ -474,25 +474,29 @@ dma_unmap_sg(struct device *dev, struct scatterlist *sg, int nents, } } -void -dma_sync_single_for_cpu(struct device *dev, dma_addr_t dma_addr, size_t size, - enum dma_data_direction dir) +void dma_sync_single_range_for_cpu(struct device *dev, dma_addr_t dma_addr, + unsigned long offset, size_t size, + enum dma_data_direction dir) { - dev_dbg(dev, "%s(ptr=%p,size=%d,dir=%x)\n", - __func__, (void *) dma_addr, size, dir); + dev_dbg(dev, "%s(dma=%#x,off=%#lx,size=%zx,dir=%x)\n", + __func__, dma_addr, offset, size, dir); - sync_single(dev, dma_addr, size, dir); + if (sync_single(dev, dma_addr, offset + size, dir)) + dma_cache_maint(dma_to_virt(dev, dma_addr) + offset, size, dir); } +EXPORT_SYMBOL(dma_sync_single_range_for_cpu); -void -dma_sync_single_for_device(struct device *dev, dma_addr_t dma_addr, size_t size, - enum dma_data_direction dir) +void dma_sync_single_range_for_device(struct device *dev, dma_addr_t dma_addr, + unsigned long offset, size_t size, + enum dma_data_direction dir) { - dev_dbg(dev, "%s(ptr=%p,size=%d,dir=%x)\n", - __func__, (void *) dma_addr, size, dir); + dev_dbg(dev, "%s(dma=%#x,off=%#lx,size=%zx,dir=%x)\n", + __func__, dma_addr, offset, size, dir); - sync_single(dev, dma_addr, size, dir); + if (sync_single(dev, dma_addr, offset + size, dir)) + dma_cache_maint(dma_to_virt(dev, dma_addr) + offset, size, dir); } +EXPORT_SYMBOL(dma_sync_single_range_for_device); void dma_sync_sg_for_cpu(struct device *dev, struct scatterlist *sg, int nents, @@ -644,8 +648,6 @@ EXPORT_SYMBOL(dma_map_single); EXPORT_SYMBOL(dma_unmap_single); EXPORT_SYMBOL(dma_map_sg); EXPORT_SYMBOL(dma_unmap_sg); -EXPORT_SYMBOL(dma_sync_single_for_cpu); -EXPORT_SYMBOL(dma_sync_single_for_device); EXPORT_SYMBOL(dma_sync_sg_for_cpu); EXPORT_SYMBOL(dma_sync_sg_for_device); EXPORT_SYMBOL(dmabounce_register_dev); diff --git a/arch/arm/include/asm/dma-mapping.h b/arch/arm/include/asm/dma-mapping.h index 6f45959fe2c..7b95d205839 100644 --- a/arch/arm/include/asm/dma-mapping.h +++ b/arch/arm/include/asm/dma-mapping.h @@ -351,11 +351,12 @@ extern void dma_unmap_sg(struct device *, struct scatterlist *, int, enum dma_da /** - * dma_sync_single_for_cpu + * dma_sync_single_range_for_cpu * @dev: valid struct device pointer, or NULL for ISA and EISA-like devices * @handle: DMA address of buffer - * @size: size of buffer to map - * @dir: DMA transfer direction + * @offset: offset of region to start sync + * @size: size of region to sync + * @dir: DMA transfer direction (same as passed to dma_map_single) * * Make physical memory consistent for a single streaming mode DMA * translation after a transfer. @@ -369,25 +370,41 @@ extern void dma_unmap_sg(struct device *, struct scatterlist *, int, enum dma_da */ #ifndef CONFIG_DMABOUNCE static inline void -dma_sync_single_for_cpu(struct device *dev, dma_addr_t handle, size_t size, - enum dma_data_direction dir) +dma_sync_single_range_for_cpu(struct device *dev, dma_addr_t handle, + unsigned long offset, size_t size, + enum dma_data_direction dir) { if (!arch_is_coherent()) - dma_cache_maint(dma_to_virt(dev, handle), size, dir); + dma_cache_maint(dma_to_virt(dev, handle) + offset, size, dir); } static inline void -dma_sync_single_for_device(struct device *dev, dma_addr_t handle, size_t size, - enum dma_data_direction dir) +dma_sync_single_range_for_device(struct device *dev, dma_addr_t handle, + unsigned long offset, size_t size, + enum dma_data_direction dir) { if (!arch_is_coherent()) - dma_cache_maint(dma_to_virt(dev, handle), size, dir); + dma_cache_maint(dma_to_virt(dev, handle) + offset, size, dir); } #else -extern void dma_sync_single_for_cpu(struct device*, dma_addr_t, size_t, enum dma_data_direction); -extern void dma_sync_single_for_device(struct device*, dma_addr_t, size_t, enum dma_data_direction); +extern void dma_sync_single_range_for_cpu(struct device *, dma_addr_t, unsigned long, size_t, enum dma_data_direction); +extern void dma_sync_single_range_for_device(struct device *, dma_addr_t, unsigned long, size_t, enum dma_data_direction); #endif +static inline void +dma_sync_single_for_cpu(struct device *dev, dma_addr_t handle, size_t size, + enum dma_data_direction dir) +{ + dma_sync_single_range_for_cpu(dev, handle, 0, size, dir); +} + +static inline void +dma_sync_single_for_device(struct device *dev, dma_addr_t handle, size_t size, + enum dma_data_direction dir) +{ + dma_sync_single_range_for_device(dev, handle, 0, size, dir); +} + /** * dma_sync_sg_for_cpu -- GitLab From cbbdece3048d0844b1cc6f4f8d18085e190721d7 Mon Sep 17 00:00:00 2001 From: Andrew Morton Date: Sun, 10 Aug 2008 23:06:25 -0400 Subject: [PATCH 089/750] Input: xilinx_ps2 - fix warning drivers/input/serio/xilinx_ps2.c:272: warning: cast from pointer to integer of different size Signed-off-by: Andrew Morton Signed-off-by: Dmitry Torokhov --- drivers/input/serio/xilinx_ps2.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/input/serio/xilinx_ps2.c b/drivers/input/serio/xilinx_ps2.c index 0ed044d5e68..765007899d9 100644 --- a/drivers/input/serio/xilinx_ps2.c +++ b/drivers/input/serio/xilinx_ps2.c @@ -269,8 +269,8 @@ static int xps2_setup(struct device *dev, struct resource *regs_res, * we have the PS2 in a good state */ out_be32(drvdata->base_address + XPS2_SRST_OFFSET, XPS2_SRST_RESET); - dev_info(dev, "Xilinx PS2 at 0x%08X mapped to 0x%08X, irq=%d\n", - drvdata->phys_addr, (u32)drvdata->base_address, drvdata->irq); + dev_info(dev, "Xilinx PS2 at 0x%08X mapped to 0x%p, irq=%d\n", + drvdata->phys_addr, drvdata->base_address, drvdata->irq); serio = &drvdata->serio; serio->id.type = SERIO_8042; -- GitLab From bc0fde2fad007a81ecffceb25a893a6c3f1ed767 Mon Sep 17 00:00:00 2001 From: Sven Wegener Date: Sun, 10 Aug 2008 09:14:05 +0000 Subject: [PATCH 090/750] ipvs: Fix possible deadlock in sync code Commit 998e7a76804b7a273a0460c2cdd5a51fa9856717 ("ipvs: Use kthread_run() instead of doing a double-fork via kernel_thread()") introduced a possible deadlock in the sync code. We need to use the _bh versions for the lock, as the lock is also accessed from a bottom half. Signed-off-by: Sven Wegener Acked-by: Simon Horman --- net/ipv4/ipvs/ip_vs_sync.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/net/ipv4/ipvs/ip_vs_sync.c b/net/ipv4/ipvs/ip_vs_sync.c index 45e9bd96c28..a652da2c320 100644 --- a/net/ipv4/ipvs/ip_vs_sync.c +++ b/net/ipv4/ipvs/ip_vs_sync.c @@ -904,9 +904,9 @@ int stop_sync_thread(int state) * progress of stopping the master sync daemon. */ - spin_lock(&ip_vs_sync_lock); + spin_lock_bh(&ip_vs_sync_lock); ip_vs_sync_state &= ~IP_VS_STATE_MASTER; - spin_unlock(&ip_vs_sync_lock); + spin_unlock_bh(&ip_vs_sync_lock); kthread_stop(sync_master_thread); sync_master_thread = NULL; } else if (state == IP_VS_STATE_BACKUP) { -- GitLab From 8ab19ea36c5c5340ff598e4d15fc084eb65671dc Mon Sep 17 00:00:00 2001 From: Sven Wegener Date: Sun, 10 Aug 2008 09:17:59 +0000 Subject: [PATCH 091/750] ipvs: Fix possible deadlock in estimator code There is a slight chance for a deadlock in the estimator code. We can't call del_timer_sync() while holding our lock, as the timer might be active and spinning for the lock on another cpu. Work around this issue by using try_to_del_timer_sync() and releasing the lock. We could actually delete the timer outside of our lock, as the add and kill functions are only every called from userspace via [gs]etsockopt() and are serialized by a mutex, but better make this explicit. Signed-off-by: Sven Wegener Cc: stable Acked-by: Simon Horman --- net/ipv4/ipvs/ip_vs_est.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) diff --git a/net/ipv4/ipvs/ip_vs_est.c b/net/ipv4/ipvs/ip_vs_est.c index bc04eedd6db..1d6e58e502f 100644 --- a/net/ipv4/ipvs/ip_vs_est.c +++ b/net/ipv4/ipvs/ip_vs_est.c @@ -170,8 +170,11 @@ void ip_vs_kill_estimator(struct ip_vs_stats *stats) kfree(est); killed++; } - if (killed && est_list == NULL) - del_timer_sync(&est_timer); + while (killed && !est_list && try_to_del_timer_sync(&est_timer) < 0) { + write_unlock_bh(&est_lock); + cpu_relax(); + write_lock_bh(&est_lock); + } write_unlock_bh(&est_lock); } -- GitLab From afdd614071aef652f5a3e2a06965de049dd8339b Mon Sep 17 00:00:00 2001 From: Sven Wegener Date: Sun, 10 Aug 2008 09:18:01 +0000 Subject: [PATCH 092/750] ipvs: Use ARRAY_SIZE() Signed-off-by: Sven Wegener Acked-by: Simon Horman --- include/net/ip_vs.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/net/ip_vs.h b/include/net/ip_vs.h index cbb59ebed4a..e980416bff8 100644 --- a/include/net/ip_vs.h +++ b/include/net/ip_vs.h @@ -440,7 +440,7 @@ struct ip_vs_app */ extern const char *ip_vs_proto_name(unsigned proto); extern void ip_vs_init_hash_table(struct list_head *table, int rows); -#define IP_VS_INIT_HASH_TABLE(t) ip_vs_init_hash_table(t, sizeof(t)/sizeof(t[0])) +#define IP_VS_INIT_HASH_TABLE(t) ip_vs_init_hash_table((t), ARRAY_SIZE((t))) #define IP_VS_APP_TYPE_FTP 1 -- GitLab From 66a0be47200fff30f8c482ea584052c6affb08cb Mon Sep 17 00:00:00 2001 From: Sven Wegener Date: Sun, 10 Aug 2008 09:18:02 +0000 Subject: [PATCH 093/750] ipvs: Use list_empty() instead of open-coding the same functionality Signed-off-by: Sven Wegener Acked-by: Simon Horman --- net/ipv4/ipvs/ip_vs_sched.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/net/ipv4/ipvs/ip_vs_sched.c b/net/ipv4/ipvs/ip_vs_sched.c index b6476730985..a46ad9e3501 100644 --- a/net/ipv4/ipvs/ip_vs_sched.c +++ b/net/ipv4/ipvs/ip_vs_sched.c @@ -184,7 +184,7 @@ int register_ip_vs_scheduler(struct ip_vs_scheduler *scheduler) write_lock_bh(&__ip_vs_sched_lock); - if (scheduler->n_list.next != &scheduler->n_list) { + if (!list_empty(&scheduler->n_list)) { write_unlock_bh(&__ip_vs_sched_lock); ip_vs_use_count_dec(); IP_VS_ERR("register_ip_vs_scheduler(): [%s] scheduler " @@ -229,7 +229,7 @@ int unregister_ip_vs_scheduler(struct ip_vs_scheduler *scheduler) } write_lock_bh(&__ip_vs_sched_lock); - if (scheduler->n_list.next == &scheduler->n_list) { + if (list_empty(&scheduler->n_list)) { write_unlock_bh(&__ip_vs_sched_lock); IP_VS_ERR("unregister_ip_vs_scheduler(): [%s] scheduler " "is not in the list. failed\n", scheduler->name); -- GitLab From d149ccc9cf85cdf089c1b2189ade111305712b0c Mon Sep 17 00:00:00 2001 From: Sven Wegener Date: Sun, 10 Aug 2008 09:18:02 +0000 Subject: [PATCH 094/750] ipvs: Initialize schedulers' struct list_head at compile time No need to do it at runtime and this saves a couple of bytes in the text section. Signed-off-by: Sven Wegener Acked-by: Simon Horman --- net/ipv4/ipvs/ip_vs_dh.c | 2 +- net/ipv4/ipvs/ip_vs_lblc.c | 2 +- net/ipv4/ipvs/ip_vs_lblcr.c | 2 +- net/ipv4/ipvs/ip_vs_lc.c | 2 +- net/ipv4/ipvs/ip_vs_nq.c | 2 +- net/ipv4/ipvs/ip_vs_rr.c | 2 +- net/ipv4/ipvs/ip_vs_sed.c | 2 +- net/ipv4/ipvs/ip_vs_sh.c | 2 +- net/ipv4/ipvs/ip_vs_wlc.c | 2 +- net/ipv4/ipvs/ip_vs_wrr.c | 2 +- 10 files changed, 10 insertions(+), 10 deletions(-) diff --git a/net/ipv4/ipvs/ip_vs_dh.c b/net/ipv4/ipvs/ip_vs_dh.c index 8afc1503ed2..fa66824d264 100644 --- a/net/ipv4/ipvs/ip_vs_dh.c +++ b/net/ipv4/ipvs/ip_vs_dh.c @@ -233,6 +233,7 @@ static struct ip_vs_scheduler ip_vs_dh_scheduler = .name = "dh", .refcnt = ATOMIC_INIT(0), .module = THIS_MODULE, + .n_list = LIST_HEAD_INIT(ip_vs_dh_scheduler.n_list), .init_service = ip_vs_dh_init_svc, .done_service = ip_vs_dh_done_svc, .update_service = ip_vs_dh_update_svc, @@ -242,7 +243,6 @@ static struct ip_vs_scheduler ip_vs_dh_scheduler = static int __init ip_vs_dh_init(void) { - INIT_LIST_HEAD(&ip_vs_dh_scheduler.n_list); return register_ip_vs_scheduler(&ip_vs_dh_scheduler); } diff --git a/net/ipv4/ipvs/ip_vs_lblc.c b/net/ipv4/ipvs/ip_vs_lblc.c index 0efa3db4b18..7a6a319f544 100644 --- a/net/ipv4/ipvs/ip_vs_lblc.c +++ b/net/ipv4/ipvs/ip_vs_lblc.c @@ -539,6 +539,7 @@ static struct ip_vs_scheduler ip_vs_lblc_scheduler = .name = "lblc", .refcnt = ATOMIC_INIT(0), .module = THIS_MODULE, + .n_list = LIST_HEAD_INIT(ip_vs_lblc_scheduler.n_list), .init_service = ip_vs_lblc_init_svc, .done_service = ip_vs_lblc_done_svc, .update_service = ip_vs_lblc_update_svc, @@ -550,7 +551,6 @@ static int __init ip_vs_lblc_init(void) { int ret; - INIT_LIST_HEAD(&ip_vs_lblc_scheduler.n_list); sysctl_header = register_sysctl_paths(net_vs_ctl_path, vs_vars_table); ret = register_ip_vs_scheduler(&ip_vs_lblc_scheduler); if (ret) diff --git a/net/ipv4/ipvs/ip_vs_lblcr.c b/net/ipv4/ipvs/ip_vs_lblcr.c index 8e3bbeb4513..c234e73968a 100644 --- a/net/ipv4/ipvs/ip_vs_lblcr.c +++ b/net/ipv4/ipvs/ip_vs_lblcr.c @@ -728,6 +728,7 @@ static struct ip_vs_scheduler ip_vs_lblcr_scheduler = .name = "lblcr", .refcnt = ATOMIC_INIT(0), .module = THIS_MODULE, + .n_list = LIST_HEAD_INIT(ip_vs_lblcr_scheduler.n_list), .init_service = ip_vs_lblcr_init_svc, .done_service = ip_vs_lblcr_done_svc, .update_service = ip_vs_lblcr_update_svc, @@ -739,7 +740,6 @@ static int __init ip_vs_lblcr_init(void) { int ret; - INIT_LIST_HEAD(&ip_vs_lblcr_scheduler.n_list); sysctl_header = register_sysctl_paths(net_vs_ctl_path, vs_vars_table); ret = register_ip_vs_scheduler(&ip_vs_lblcr_scheduler); if (ret) diff --git a/net/ipv4/ipvs/ip_vs_lc.c b/net/ipv4/ipvs/ip_vs_lc.c index ac9f08e065d..ebcdbf75ac6 100644 --- a/net/ipv4/ipvs/ip_vs_lc.c +++ b/net/ipv4/ipvs/ip_vs_lc.c @@ -98,6 +98,7 @@ static struct ip_vs_scheduler ip_vs_lc_scheduler = { .name = "lc", .refcnt = ATOMIC_INIT(0), .module = THIS_MODULE, + .n_list = LIST_HEAD_INIT(ip_vs_lc_scheduler.n_list), .init_service = ip_vs_lc_init_svc, .done_service = ip_vs_lc_done_svc, .update_service = ip_vs_lc_update_svc, @@ -107,7 +108,6 @@ static struct ip_vs_scheduler ip_vs_lc_scheduler = { static int __init ip_vs_lc_init(void) { - INIT_LIST_HEAD(&ip_vs_lc_scheduler.n_list); return register_ip_vs_scheduler(&ip_vs_lc_scheduler) ; } diff --git a/net/ipv4/ipvs/ip_vs_nq.c b/net/ipv4/ipvs/ip_vs_nq.c index a46bf258d42..92f3a677003 100644 --- a/net/ipv4/ipvs/ip_vs_nq.c +++ b/net/ipv4/ipvs/ip_vs_nq.c @@ -136,6 +136,7 @@ static struct ip_vs_scheduler ip_vs_nq_scheduler = .name = "nq", .refcnt = ATOMIC_INIT(0), .module = THIS_MODULE, + .n_list = LIST_HEAD_INIT(ip_vs_nq_scheduler.n_list), .init_service = ip_vs_nq_init_svc, .done_service = ip_vs_nq_done_svc, .update_service = ip_vs_nq_update_svc, @@ -145,7 +146,6 @@ static struct ip_vs_scheduler ip_vs_nq_scheduler = static int __init ip_vs_nq_init(void) { - INIT_LIST_HEAD(&ip_vs_nq_scheduler.n_list); return register_ip_vs_scheduler(&ip_vs_nq_scheduler); } diff --git a/net/ipv4/ipvs/ip_vs_rr.c b/net/ipv4/ipvs/ip_vs_rr.c index c8db12d39e6..358110d17e5 100644 --- a/net/ipv4/ipvs/ip_vs_rr.c +++ b/net/ipv4/ipvs/ip_vs_rr.c @@ -94,6 +94,7 @@ static struct ip_vs_scheduler ip_vs_rr_scheduler = { .name = "rr", /* name */ .refcnt = ATOMIC_INIT(0), .module = THIS_MODULE, + .n_list = LIST_HEAD_INIT(ip_vs_rr_scheduler.n_list), .init_service = ip_vs_rr_init_svc, .done_service = ip_vs_rr_done_svc, .update_service = ip_vs_rr_update_svc, @@ -102,7 +103,6 @@ static struct ip_vs_scheduler ip_vs_rr_scheduler = { static int __init ip_vs_rr_init(void) { - INIT_LIST_HEAD(&ip_vs_rr_scheduler.n_list); return register_ip_vs_scheduler(&ip_vs_rr_scheduler); } diff --git a/net/ipv4/ipvs/ip_vs_sed.c b/net/ipv4/ipvs/ip_vs_sed.c index 2a7d3135818..77663d84cbd 100644 --- a/net/ipv4/ipvs/ip_vs_sed.c +++ b/net/ipv4/ipvs/ip_vs_sed.c @@ -138,6 +138,7 @@ static struct ip_vs_scheduler ip_vs_sed_scheduler = .name = "sed", .refcnt = ATOMIC_INIT(0), .module = THIS_MODULE, + .n_list = LIST_HEAD_INIT(ip_vs_sed_scheduler.n_list), .init_service = ip_vs_sed_init_svc, .done_service = ip_vs_sed_done_svc, .update_service = ip_vs_sed_update_svc, @@ -147,7 +148,6 @@ static struct ip_vs_scheduler ip_vs_sed_scheduler = static int __init ip_vs_sed_init(void) { - INIT_LIST_HEAD(&ip_vs_sed_scheduler.n_list); return register_ip_vs_scheduler(&ip_vs_sed_scheduler); } diff --git a/net/ipv4/ipvs/ip_vs_sh.c b/net/ipv4/ipvs/ip_vs_sh.c index b8fdfac6500..7b979e22805 100644 --- a/net/ipv4/ipvs/ip_vs_sh.c +++ b/net/ipv4/ipvs/ip_vs_sh.c @@ -230,6 +230,7 @@ static struct ip_vs_scheduler ip_vs_sh_scheduler = .name = "sh", .refcnt = ATOMIC_INIT(0), .module = THIS_MODULE, + .n_list = LIST_HEAD_INIT(ip_vs_sh_scheduler.n_list), .init_service = ip_vs_sh_init_svc, .done_service = ip_vs_sh_done_svc, .update_service = ip_vs_sh_update_svc, @@ -239,7 +240,6 @@ static struct ip_vs_scheduler ip_vs_sh_scheduler = static int __init ip_vs_sh_init(void) { - INIT_LIST_HEAD(&ip_vs_sh_scheduler.n_list); return register_ip_vs_scheduler(&ip_vs_sh_scheduler); } diff --git a/net/ipv4/ipvs/ip_vs_wlc.c b/net/ipv4/ipvs/ip_vs_wlc.c index 772c3cb4eca..9b0ef86bb1f 100644 --- a/net/ipv4/ipvs/ip_vs_wlc.c +++ b/net/ipv4/ipvs/ip_vs_wlc.c @@ -126,6 +126,7 @@ static struct ip_vs_scheduler ip_vs_wlc_scheduler = .name = "wlc", .refcnt = ATOMIC_INIT(0), .module = THIS_MODULE, + .n_list = LIST_HEAD_INIT(ip_vs_wlc_scheduler.n_list), .init_service = ip_vs_wlc_init_svc, .done_service = ip_vs_wlc_done_svc, .update_service = ip_vs_wlc_update_svc, @@ -135,7 +136,6 @@ static struct ip_vs_scheduler ip_vs_wlc_scheduler = static int __init ip_vs_wlc_init(void) { - INIT_LIST_HEAD(&ip_vs_wlc_scheduler.n_list); return register_ip_vs_scheduler(&ip_vs_wlc_scheduler); } diff --git a/net/ipv4/ipvs/ip_vs_wrr.c b/net/ipv4/ipvs/ip_vs_wrr.c index 1d6932d7dc9..0d86a79b87b 100644 --- a/net/ipv4/ipvs/ip_vs_wrr.c +++ b/net/ipv4/ipvs/ip_vs_wrr.c @@ -212,6 +212,7 @@ static struct ip_vs_scheduler ip_vs_wrr_scheduler = { .name = "wrr", .refcnt = ATOMIC_INIT(0), .module = THIS_MODULE, + .n_list = LIST_HEAD_INIT(ip_vs_wrr_scheduler.n_list), .init_service = ip_vs_wrr_init_svc, .done_service = ip_vs_wrr_done_svc, .update_service = ip_vs_wrr_update_svc, @@ -220,7 +221,6 @@ static struct ip_vs_scheduler ip_vs_wrr_scheduler = { static int __init ip_vs_wrr_init(void) { - INIT_LIST_HEAD(&ip_vs_wrr_scheduler.n_list); return register_ip_vs_scheduler(&ip_vs_wrr_scheduler) ; } -- GitLab From 048cf48b897bcae9e6fa8b46b6976dab5e710e3c Mon Sep 17 00:00:00 2001 From: Sven Wegener Date: Sun, 10 Aug 2008 18:24:35 +0000 Subject: [PATCH 095/750] ipvs: Annotate init functions with __init Being able to discard these functions saves a couple of bytes at runtime. The cleanup functions can't be annotated with __exit as they are also called from init functions. Signed-off-by: Sven Wegener Acked-by: Simon Horman --- net/ipv4/ipvs/ip_vs_app.c | 2 +- net/ipv4/ipvs/ip_vs_conn.c | 2 +- net/ipv4/ipvs/ip_vs_ctl.c | 2 +- net/ipv4/ipvs/ip_vs_proto.c | 4 ++-- 4 files changed, 5 insertions(+), 5 deletions(-) diff --git a/net/ipv4/ipvs/ip_vs_app.c b/net/ipv4/ipvs/ip_vs_app.c index 1f1897a1a70..201b8ea3020 100644 --- a/net/ipv4/ipvs/ip_vs_app.c +++ b/net/ipv4/ipvs/ip_vs_app.c @@ -608,7 +608,7 @@ int ip_vs_skb_replace(struct sk_buff *skb, gfp_t pri, } -int ip_vs_app_init(void) +int __init ip_vs_app_init(void) { /* we will replace it with proc_net_ipvs_create() soon */ proc_net_fops_create(&init_net, "ip_vs_app", 0, &ip_vs_app_fops); diff --git a/net/ipv4/ipvs/ip_vs_conn.c b/net/ipv4/ipvs/ip_vs_conn.c index f8bdae47a77..44a6872dc24 100644 --- a/net/ipv4/ipvs/ip_vs_conn.c +++ b/net/ipv4/ipvs/ip_vs_conn.c @@ -965,7 +965,7 @@ static void ip_vs_conn_flush(void) } -int ip_vs_conn_init(void) +int __init ip_vs_conn_init(void) { int idx; diff --git a/net/ipv4/ipvs/ip_vs_ctl.c b/net/ipv4/ipvs/ip_vs_ctl.c index 9a5ace0b4dd..df13333813a 100644 --- a/net/ipv4/ipvs/ip_vs_ctl.c +++ b/net/ipv4/ipvs/ip_vs_ctl.c @@ -2306,7 +2306,7 @@ static struct nf_sockopt_ops ip_vs_sockopts = { }; -int ip_vs_control_init(void) +int __init ip_vs_control_init(void) { int ret; int idx; diff --git a/net/ipv4/ipvs/ip_vs_proto.c b/net/ipv4/ipvs/ip_vs_proto.c index 876714f23d6..6099a88fc20 100644 --- a/net/ipv4/ipvs/ip_vs_proto.c +++ b/net/ipv4/ipvs/ip_vs_proto.c @@ -43,7 +43,7 @@ static struct ip_vs_protocol *ip_vs_proto_table[IP_VS_PROTO_TAB_SIZE]; /* * register an ipvs protocol */ -static int __used register_ip_vs_protocol(struct ip_vs_protocol *pp) +static int __used __init register_ip_vs_protocol(struct ip_vs_protocol *pp) { unsigned hash = IP_VS_PROTO_HASH(pp->protocol); @@ -190,7 +190,7 @@ ip_vs_tcpudp_debug_packet(struct ip_vs_protocol *pp, } -int ip_vs_protocol_init(void) +int __init ip_vs_protocol_init(void) { char protocols[64]; #define REGISTER_PROTOCOL(p) \ -- GitLab From 5587da55fbf332ab8d1b37637536f94bc373867f Mon Sep 17 00:00:00 2001 From: Sven Wegener Date: Sun, 10 Aug 2008 18:24:40 +0000 Subject: [PATCH 096/750] ipvs: Mark net_vs_ctl_path const Signed-off-by: Sven Wegener Acked-by: Simon Horman --- include/net/ip_vs.h | 2 +- net/ipv4/ipvs/ip_vs_ctl.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/include/net/ip_vs.h b/include/net/ip_vs.h index e980416bff8..c8ee9b89b02 100644 --- a/include/net/ip_vs.h +++ b/include/net/ip_vs.h @@ -620,7 +620,7 @@ extern int sysctl_ip_vs_expire_quiescent_template; extern int sysctl_ip_vs_sync_threshold[2]; extern int sysctl_ip_vs_nat_icmp_send; extern struct ip_vs_stats ip_vs_stats; -extern struct ctl_path net_vs_ctl_path[]; +extern const struct ctl_path net_vs_ctl_path[]; extern struct ip_vs_service * ip_vs_service_get(__u32 fwmark, __u16 protocol, __be32 vaddr, __be16 vport); diff --git a/net/ipv4/ipvs/ip_vs_ctl.c b/net/ipv4/ipvs/ip_vs_ctl.c index df13333813a..999d884e886 100644 --- a/net/ipv4/ipvs/ip_vs_ctl.c +++ b/net/ipv4/ipvs/ip_vs_ctl.c @@ -1589,7 +1589,7 @@ static struct ctl_table vs_vars[] = { { .ctl_name = 0 } }; -struct ctl_path net_vs_ctl_path[] = { +const struct ctl_path net_vs_ctl_path[] = { { .procname = "net", .ctl_name = CTL_NET, }, { .procname = "ipv4", .ctl_name = NET_IPV4, }, { .procname = "vs", }, -- GitLab From e77eb36472cdc425a3a81356c7b368e59a36da31 Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Tue, 5 Aug 2008 13:16:56 +0900 Subject: [PATCH 097/750] sh: mach-x3proto: Fix up smc91x platform data. smc91x on x3proto needs 16-bit access and nowait, which we can now do through the platform data. Signed-off-by: Paul Mundt --- arch/sh/boards/mach-x3proto/setup.c | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-) diff --git a/arch/sh/boards/mach-x3proto/setup.c b/arch/sh/boards/mach-x3proto/setup.c index abc5b6d418f..a70d23b2178 100644 --- a/arch/sh/boards/mach-x3proto/setup.c +++ b/arch/sh/boards/mach-x3proto/setup.c @@ -3,7 +3,7 @@ * * Renesas SH-X3 Prototype Board Support. * - * Copyright (C) 2007 Paul Mundt + * Copyright (C) 2007 - 2008 Paul Mundt * * This file is subject to the terms and conditions of the GNU General Public * License. See the file "COPYING" in the main directory of this archive @@ -13,6 +13,7 @@ #include #include #include +#include #include static struct resource heartbeat_resources[] = { @@ -30,6 +31,10 @@ static struct platform_device heartbeat_device = { .resource = heartbeat_resources, }; +static struct smc91x_platdata smc91x_info = { + .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT, +}; + static struct resource smc91x_resources[] = { [0] = { .start = 0x18000300, @@ -47,6 +52,9 @@ static struct platform_device smc91x_device = { .id = -1, .resource = smc91x_resources, .num_resources = ARRAY_SIZE(smc91x_resources), + .dev = { + .platform_data = &smc91x_info, + }, }; static struct resource r8a66597_usb_host_resources[] = { -- GitLab From 7265706c8fd57722f622f336ec110cb35f83e739 Mon Sep 17 00:00:00 2001 From: Adrian Bunk Date: Tue, 5 Aug 2008 18:37:11 +0300 Subject: [PATCH 098/750] fix SH7705_CACHE_32KB compilation This patches compile errors like the following caused by commit 51f3547d619956e9b428bfff17004d8f4d259a02 (sh: Allow SH-3 and SH-5 to use common headers): <-- snip --> ... CC arch/sh/mm/init.o /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/mm/init.c: In function 'mem_init': /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/mm/init.c:232: error: implicit declaration of function 'p3_cache_init' make[2]: *** [arch/sh/mm/init.o] Error 1 make[1]: *** [arch/sh/mm] Error 2 ... CC kernel/fork.o /home/bunk/linux/kernel-2.6/git/linux-2.6/kernel/fork.c: In function 'dup_mmap': /home/bunk/linux/kernel-2.6/git/linux-2.6/kernel/fork.c:323: error: implicit declaration of function 'flush_dcache_mmap_lock' /home/bunk/linux/kernel-2.6/git/linux-2.6/kernel/fork.c:325: error: implicit declaration of function 'flush_dcache_mmap_unlock' make[2]: *** [kernel/fork.o] Error 1 <-- snip --> Reported-by: Adrian Bunk Signed-off-by: Adrian Bunk Signed-off-by: Paul Mundt --- arch/sh/include/cpu-sh3/cpu/cacheflush.h | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/sh/include/cpu-sh3/cpu/cacheflush.h b/arch/sh/include/cpu-sh3/cpu/cacheflush.h index abc90988080..1ac27aae670 100644 --- a/arch/sh/include/cpu-sh3/cpu/cacheflush.h +++ b/arch/sh/include/cpu-sh3/cpu/cacheflush.h @@ -29,6 +29,16 @@ void flush_cache_page(struct vm_area_struct *vma, unsigned long addr, unsigned l void flush_dcache_page(struct page *pg); void flush_icache_range(unsigned long start, unsigned long end); void flush_icache_page(struct vm_area_struct *vma, struct page *page); + +#define flush_dcache_mmap_lock(mapping) do { } while (0) +#define flush_dcache_mmap_unlock(mapping) do { } while (0) + +/* SH3 has unified cache so no special action needed here */ +#define flush_cache_sigtramp(vaddr) do { } while (0) +#define flush_icache_user_range(vma,pg,adr,len) do { } while (0) + +#define p3_cache_init() do { } while (0) + #else #include #endif -- GitLab From d09d328c119a9ac20615fc8b1431aa417955ad4d Mon Sep 17 00:00:00 2001 From: Yoshinori Sato Date: Wed, 6 Aug 2008 14:47:54 +0900 Subject: [PATCH 099/750] sh: Don't export __{s,u}divsi3_i4i from SH-2 libgcc. rsk7203_defconfig fails to build with the following error: <-- snip --> ... LD .tmp_vmlinux1 arch/sh/kernel/built-in.o:(__ksymtab+0xb8): undefined reference to `__udivsi3_i4i' arch/sh/kernel/built-in.o:(__ksymtab+0xc8): undefined reference to `__sdivsi3_i4i' make[1]: *** [.tmp_vmlinux1] Error 1 <-- snip --> That worked with 2.6.26, and these are far less undefined references than in the cases where libgcc was missing. [ These symbols are not defined on SH-2 versions of libgcc, so we have to special case the export there. - Paul ] Reported-by: Adrian Bunk Signed-off-by: Yoshinori Sato Signed-off-by: Paul Mundt --- arch/sh/kernel/sh_ksyms_32.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/arch/sh/kernel/sh_ksyms_32.c b/arch/sh/kernel/sh_ksyms_32.c index 8f916536719..6e1b1c27165 100644 --- a/arch/sh/kernel/sh_ksyms_32.c +++ b/arch/sh/kernel/sh_ksyms_32.c @@ -107,10 +107,12 @@ DECLARE_EXPORT(__movmemSI12_i4); * GCC >= 4.2 emits these for division, as do GCC 4.1.x versions of the ST * compiler which include backported patches. */ -DECLARE_EXPORT(__sdivsi3_i4i); DECLARE_EXPORT(__udiv_qrnnd_16); +#if !defined(CONFIG_CPU_SH2) +DECLARE_EXPORT(__sdivsi3_i4i); DECLARE_EXPORT(__udivsi3_i4i); #endif +#endif #else /* GCC 3.x */ DECLARE_EXPORT(__movstr_i4_even); DECLARE_EXPORT(__movstr_i4_odd); -- GitLab From 68b7c24cf9c699ed93c4a70f958b5bb3943723bc Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Wed, 6 Aug 2008 15:10:49 +0900 Subject: [PATCH 100/750] sh: Disable 64kB hugetlbpage size when using 64kB PAGE_SIZE. Presently we oops in mm/hugetlb.c:1325, which is the order == 0 test in hugetlb_add_hstate() called at initialization time. So, disable 64kB huge pages when we're using a 64kB PAGE_SIZE. On most parts this will force the default to be 1MB huge pages. Signed-off-by: Paul Mundt --- arch/sh/mm/Kconfig | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/sh/mm/Kconfig b/arch/sh/mm/Kconfig index 9c131cac91a..8a03926ea84 100644 --- a/arch/sh/mm/Kconfig +++ b/arch/sh/mm/Kconfig @@ -181,10 +181,12 @@ config ENTRY_OFFSET choice prompt "HugeTLB page size" depends on HUGETLB_PAGE && (CPU_SH4 || CPU_SH5) && MMU + default HUGETLB_PAGE_SIZE_1MB if PAGE_SIZE_64KB default HUGETLB_PAGE_SIZE_64K config HUGETLB_PAGE_SIZE_64K bool "64kB" + depends on !PAGE_SIZE_64KB config HUGETLB_PAGE_SIZE_256K bool "256kB" -- GitLab From 0a766a6b7dd9f3d15c32d724555d954dc6bb020d Mon Sep 17 00:00:00 2001 From: Nobuhiro Iwamatsu Date: Fri, 8 Aug 2008 14:29:58 +0900 Subject: [PATCH 101/750] sh: Add support sh_eth to sh7763rdp board SH7763 has sh_eth device. This patch add sh_eth platform device to this board. Signed-off-by: Nobuhiro Iwamatsu Signed-off-by: Paul Mundt --- arch/sh/boards/mach-sh7763rdp/setup.c | 34 +++++++++++++++++++++++++-- 1 file changed, 32 insertions(+), 2 deletions(-) diff --git a/arch/sh/boards/mach-sh7763rdp/setup.c b/arch/sh/boards/mach-sh7763rdp/setup.c index 925f16af712..49940d192d6 100644 --- a/arch/sh/boards/mach-sh7763rdp/setup.c +++ b/arch/sh/boards/mach-sh7763rdp/setup.c @@ -15,8 +15,9 @@ #include #include #include -#include +#include #include +#include /* NOR Flash */ static struct mtd_partition sh7763rdp_nor_flash_partitions[] = { @@ -60,8 +61,36 @@ static struct platform_device sh7763rdp_nor_flash_device = { }, }; +/* SH-Ether */ +static struct resource sh_eth_resources[] = { + { + .start = 0xFEE00800, /* use eth1 */ + .end = 0xFEE00F7C - 1, + .flags = IORESOURCE_MEM, + }, { + .start = 58, /* irq number */ + .end = 58, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct sh_eth_plat_data sh7763_eth_pdata = { + .phy = 1, + .edmac_endian = EDMAC_LITTLE_ENDIAN, +}; + +static struct platform_device sh7763rdp_eth_device = { + .name = "sh-eth", + .resource = sh_eth_resources, + .num_resources = ARRAY_SIZE(sh_eth_resources), + .dev = { + .platform_data = &sh7763_eth_pdata, + }, +}; + static struct platform_device *sh7763rdp_devices[] __initdata = { &sh7763rdp_nor_flash_device, + &sh7763rdp_eth_device, }; static int __init sh7763rdp_devices_setup(void) @@ -69,7 +98,8 @@ static int __init sh7763rdp_devices_setup(void) return platform_add_devices(sh7763rdp_devices, ARRAY_SIZE(sh7763rdp_devices)); } -__initcall(sh7763rdp_devices_setup); + +device_initcall(sh7763rdp_devices_setup); static void __init sh7763rdp_setup(char **cmdline_p) { -- GitLab From 674063c5a5461e39c0eb0b33570d467708ec0ecd Mon Sep 17 00:00:00 2001 From: Nobuhiro Iwamatsu Date: Fri, 8 Aug 2008 14:30:06 +0900 Subject: [PATCH 102/750] sh: Add support sh7760fb to sh7763rdp board Add sh7760fb platform device to sh7763rdp's setup. Signed-off-by: Paul Mundt --- arch/sh/boards/mach-sh7763rdp/setup.c | 52 ++++++++++++++++++++++++++- 1 file changed, 51 insertions(+), 1 deletion(-) diff --git a/arch/sh/boards/mach-sh7763rdp/setup.c b/arch/sh/boards/mach-sh7763rdp/setup.c index 49940d192d6..23850da05e3 100644 --- a/arch/sh/boards/mach-sh7763rdp/setup.c +++ b/arch/sh/boards/mach-sh7763rdp/setup.c @@ -15,9 +15,11 @@ #include #include #include +#include #include #include #include +#include /* NOR Flash */ static struct mtd_partition sh7763rdp_nor_flash_partitions[] = { @@ -88,9 +90,58 @@ static struct platform_device sh7763rdp_eth_device = { }, }; +/* SH7763 LCDC */ +static struct resource sh7763rdp_fb_resources[] = { + { + .start = 0xFFE80000, + .end = 0xFFE80442 - 1, + .flags = IORESOURCE_MEM, + }, +}; + +static struct fb_videomode sh7763fb_videomode = { + .refresh = 60, + .name = "VGA Monitor", + .xres = 640, + .yres = 480, + .pixclock = 10000, + .left_margin = 80, + .right_margin = 24, + .upper_margin = 30, + .lower_margin = 1, + .hsync_len = 96, + .vsync_len = 1, + .sync = 0, + .vmode = FB_VMODE_NONINTERLACED, + .flag = FBINFO_FLAG_DEFAULT, +}; + +static struct sh7760fb_platdata sh7763fb_def_pdata = { + .def_mode = &sh7763fb_videomode, + .ldmtr = (LDMTR_TFT_COLOR_16|LDMTR_MCNT), + .lddfr = LDDFR_16BPP_RGB565, + .ldpmmr = 0x0000, + .ldpspr = 0xFFFF, + .ldaclnr = 0x0001, + .ldickr = 0x1102, + .rotate = 0, + .novsync = 0, + .blank = NULL, +}; + +static struct platform_device sh7763rdp_fb_device = { + .name = "sh7760-lcdc", + .resource = sh7763rdp_fb_resources, + .num_resources = ARRAY_SIZE(sh7763rdp_fb_resources), + .dev = { + .platform_data = &sh7763fb_def_pdata, + }, +}; + static struct platform_device *sh7763rdp_devices[] __initdata = { &sh7763rdp_nor_flash_device, &sh7763rdp_eth_device, + &sh7763rdp_fb_device, }; static int __init sh7763rdp_devices_setup(void) @@ -98,7 +149,6 @@ static int __init sh7763rdp_devices_setup(void) return platform_add_devices(sh7763rdp_devices, ARRAY_SIZE(sh7763rdp_devices)); } - device_initcall(sh7763rdp_devices_setup); static void __init sh7763rdp_setup(char **cmdline_p) -- GitLab From a66b44b103755ecad84b4817c4e3253234d2b03d Mon Sep 17 00:00:00 2001 From: Nobuhiro Iwamatsu Date: Fri, 8 Aug 2008 14:30:13 +0900 Subject: [PATCH 103/750] sh: Update sh7763rdp defconfig Signed-off-by: Nobuhiro Iwamatsu Signed-off-by: Paul Mundt --- arch/sh/configs/sh7763rdp_defconfig | 113 ++++++++++++++++++++++++---- 1 file changed, 97 insertions(+), 16 deletions(-) diff --git a/arch/sh/configs/sh7763rdp_defconfig b/arch/sh/configs/sh7763rdp_defconfig index 83f3fe5db3e..baf830c4a7e 100644 --- a/arch/sh/configs/sh7763rdp_defconfig +++ b/arch/sh/configs/sh7763rdp_defconfig @@ -1,15 +1,17 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.26-rc4 -# Fri Jun 6 12:20:17 2008 +# Linux kernel version: 2.6.27-rc2 +# Fri Aug 8 13:44:20 2008 # CONFIG_SUPERH=y CONFIG_SUPERH32=y +CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig" CONFIG_RWSEM_GENERIC_SPINLOCK=y CONFIG_GENERIC_BUG=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_TIME=y @@ -19,7 +21,6 @@ CONFIG_LOCKDEP_SUPPORT=y # CONFIG_ARCH_HAS_ILOG2_U32 is not set # CONFIG_ARCH_HAS_ILOG2_U64 is not set CONFIG_ARCH_NO_VIRT_TO_BUS=y -CONFIG_ARCH_SUPPORTS_AOUT=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" # @@ -83,10 +84,16 @@ CONFIG_PROFILING=y # CONFIG_MARKERS is not set CONFIG_OPROFILE=y CONFIG_HAVE_OPROFILE=y +# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set +# CONFIG_HAVE_IOREMAP_PROT is not set # CONFIG_HAVE_KPROBES is not set # CONFIG_HAVE_KRETPROBES is not set +# CONFIG_HAVE_ARCH_TRACEHOOK is not set # CONFIG_HAVE_DMA_ATTRS is not set +# CONFIG_USE_GENERIC_SMP_HELPERS is not set +CONFIG_HAVE_CLK=y CONFIG_PROC_PAGE_MONITOR=y +CONFIG_HAVE_GENERIC_DMA_COHERENT=y CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set @@ -96,12 +103,13 @@ CONFIG_MODULES=y # CONFIG_MODULE_UNLOAD is not set # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set -# CONFIG_KMOD is not set +CONFIG_KMOD=y CONFIG_BLOCK=y # CONFIG_LBD is not set # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_LSF is not set # CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set # # IO Schedulers @@ -177,6 +185,7 @@ CONFIG_PAGE_SIZE_4KB=y # CONFIG_PAGE_SIZE_8KB is not set # CONFIG_PAGE_SIZE_16KB is not set # CONFIG_PAGE_SIZE_64KB is not set +CONFIG_ENTRY_OFFSET=0x00001000 CONFIG_SELECT_MEMORY_MODEL=y # CONFIG_FLATMEM_MANUAL is not set # CONFIG_DISCONTIGMEM_MANUAL is not set @@ -258,6 +267,7 @@ CONFIG_HZ=250 # CONFIG_SCHED_HRTICK is not set # CONFIG_KEXEC is not set # CONFIG_CRASH_DUMP is not set +CONFIG_SECCOMP=y CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set @@ -282,10 +292,6 @@ CONFIG_CMDLINE="console=ttySC2,115200 root=/dev/sda1 rootdelay=10" # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set - -# -# Networking -# CONFIG_NET=y # @@ -361,6 +367,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # CONFIG_CFG80211 is not set CONFIG_WIRELESS_EXT=y +CONFIG_WIRELESS_EXT_SYSFS=y # CONFIG_MAC80211 is not set # CONFIG_IEEE80211 is not set # CONFIG_RFKILL is not set @@ -377,6 +384,8 @@ CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_EXTRA_FIRMWARE="" # CONFIG_SYS_HYPERVISOR is not set # CONFIG_CONNECTOR is not set CONFIG_MTD=y @@ -471,6 +480,7 @@ CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_RAM is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set +# CONFIG_BLK_DEV_HD is not set # CONFIG_MISC_DEVICES is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -515,10 +525,10 @@ CONFIG_SCSI_WAIT_SCAN=m CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_DH is not set # CONFIG_ATA is not set # CONFIG_MD is not set CONFIG_NETDEVICES=y -# CONFIG_NETDEVICES_MULTIQUEUE is not set # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -546,7 +556,9 @@ CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_AX88796 is not set # CONFIG_STNIC is not set +CONFIG_SH_ETH=y # CONFIG_SMC91X is not set +# CONFIG_SMC911X is not set # CONFIG_IBM_NEW_EMAC_ZMII is not set # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set @@ -613,7 +625,11 @@ CONFIG_INPUT=y # # Character devices # -# CONFIG_VT is not set +CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set CONFIG_DEVKMEM=y # CONFIG_SERIAL_NONSTANDARD is not set @@ -644,6 +660,7 @@ CONFIG_HW_RANDOM=y # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set # CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set # @@ -655,6 +672,7 @@ CONFIG_SSB_POSSIBLE=y # # Multifunction device drivers # +# CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set @@ -679,7 +697,34 @@ CONFIG_SSB_POSSIBLE=y # # CONFIG_VGASTATE is not set # CONFIG_VIDEO_OUTPUT_CONTROL is not set -# CONFIG_FB is not set +CONFIG_FB=y +# CONFIG_FIRMWARE_EDID is not set +# CONFIG_FB_DDC is not set +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set +# CONFIG_FB_SYS_FILLRECT is not set +# CONFIG_FB_SYS_COPYAREA is not set +# CONFIG_FB_SYS_IMAGEBLIT is not set +CONFIG_FB_FOREIGN_ENDIAN=y +CONFIG_FB_BOTH_ENDIAN=y +# CONFIG_FB_BIG_ENDIAN is not set +# CONFIG_FB_LITTLE_ENDIAN is not set +# CONFIG_FB_SYS_FOPS is not set +# CONFIG_FB_SVGALIB is not set +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_BACKLIGHT is not set +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set + +# +# Frame buffer hardware drivers +# +# CONFIG_FB_S1D13XXX is not set +# CONFIG_FB_SH_MOBILE_LCDC is not set +CONFIG_FB_SH7760=y +# CONFIG_FB_VIRTUAL is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # @@ -688,8 +733,22 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_DISPLAY_SUPPORT is not set # -# Sound -# +# Console display driver support +# +CONFIG_DUMMY_CONSOLE=y +CONFIG_FRAMEBUFFER_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set +# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set +# CONFIG_FONTS is not set +CONFIG_FONT_8x8=y +CONFIG_FONT_8x16=y +CONFIG_LOGO=y +CONFIG_LOGO_LINUX_MONO=y +CONFIG_LOGO_LINUX_VGA16=y +CONFIG_LOGO_LINUX_CLUT224=y +CONFIG_LOGO_SUPERH_MONO=y +CONFIG_LOGO_SUPERH_VGA16=y +CONFIG_LOGO_SUPERH_CLUT224=y # CONFIG_SOUND is not set # CONFIG_HID_SUPPORT is not set CONFIG_USB_SUPPORT=y @@ -788,11 +847,27 @@ CONFIG_USB_MON=y # CONFIG_USB_IOWARRIOR is not set # CONFIG_USB_ISIGHTFW is not set # CONFIG_USB_GADGET is not set -# CONFIG_MMC is not set +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +# CONFIG_MMC_UNSAFE_RESUME is not set + +# +# MMC/SD Card Drivers +# +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_BOUNCE=y +# CONFIG_SDIO_UART is not set +# CONFIG_MMC_TEST is not set + +# +# MMC/SD Host Controller Drivers +# +# CONFIG_MMC_SDHCI is not set # CONFIG_MEMSTICK is not set # CONFIG_NEW_LEDS is not set # CONFIG_ACCESSIBILITY is not set # CONFIG_RTC_CLASS is not set +# CONFIG_DMADEVICES is not set # CONFIG_UIO is not set # @@ -865,6 +940,7 @@ CONFIG_TMPFS_POSIX_ACL=y # CONFIG_CRAMFS is not set # CONFIG_VXFS_FS is not set # CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_ROMFS_FS is not set @@ -874,12 +950,11 @@ CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y # CONFIG_NFS_V3 is not set # CONFIG_NFS_V4 is not set -# CONFIG_NFSD is not set CONFIG_ROOT_NFS=y +# CONFIG_NFSD is not set CONFIG_LOCKD=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y -# CONFIG_SUNRPC_BIND34 is not set # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set @@ -949,6 +1024,7 @@ CONFIG_FRAME_WARN=1024 # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set # CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_DEBUG_MEMORY_INIT is not set # CONFIG_SAMPLES is not set # CONFIG_SH_STANDARD_BIOS is not set # CONFIG_EARLY_SCIF_CONSOLE is not set @@ -1003,6 +1079,10 @@ CONFIG_CRYPTO=y # CONFIG_CRYPTO_MD4 is not set # CONFIG_CRYPTO_MD5 is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set # CONFIG_CRYPTO_SHA1 is not set # CONFIG_CRYPTO_SHA256 is not set # CONFIG_CRYPTO_SHA512 is not set @@ -1042,6 +1122,7 @@ CONFIG_BITREVERSE=y # CONFIG_GENERIC_FIND_FIRST_BIT is not set # CONFIG_CRC_CCITT is not set # CONFIG_CRC16 is not set +CONFIG_CRC_T10DIF=y # CONFIG_CRC_ITU_T is not set CONFIG_CRC32=y # CONFIG_CRC7 is not set -- GitLab From 2fc91882c24908f5f785ed094cfe74214c44af8d Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Mon, 11 Aug 2008 14:52:46 +0900 Subject: [PATCH 104/750] sh: remove MSTPCR defines from Migo-R header file Remove MSTPCR register definitions from Migo-R header file. The clock frame work should be used instead of direct register access. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt --- arch/sh/include/asm/migor.h | 3 --- 1 file changed, 3 deletions(-) diff --git a/arch/sh/include/asm/migor.h b/arch/sh/include/asm/migor.h index 10016e0f4a4..c12b632c540 100644 --- a/arch/sh/include/asm/migor.h +++ b/arch/sh/include/asm/migor.h @@ -42,9 +42,6 @@ #define PORT_MSELCRB 0xa4050182 -#define MSTPCR1 0xa4150034 -#define MSTPCR2 0xa4150038 - #define PORT_PSELA 0xa405014e #define PORT_PSELB 0xa4050150 #define PORT_PSELC 0xa4050152 -- GitLab From b6ce9ad05f782e6a00aed8432d9513dc394115ce Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Mon, 11 Aug 2008 14:53:49 +0900 Subject: [PATCH 105/750] input: migor_ts compile and detection fix The i2c layer got changed while the migor_ts driver was in the input tree waiting to get merged upstream. Fix current compile issue by using struct i2c_client member "name" instead of "driver_name". Also, add id_table to make sure the device gets properly detected. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt --- drivers/input/touchscreen/migor_ts.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-) diff --git a/drivers/input/touchscreen/migor_ts.c b/drivers/input/touchscreen/migor_ts.c index c1cd99d5898..504ca11749a 100644 --- a/drivers/input/touchscreen/migor_ts.c +++ b/drivers/input/touchscreen/migor_ts.c @@ -173,7 +173,7 @@ static int migor_ts_probe(struct i2c_client *client, input_set_abs_params(input, ABS_X, 95, 955, 0, 0); input_set_abs_params(input, ABS_Y, 85, 935, 0, 0); - input->name = client->driver_name; + input->name = client->name; input->id.bustype = BUS_I2C; input->dev.parent = &client->dev; @@ -192,7 +192,7 @@ static int migor_ts_probe(struct i2c_client *client, goto err1; error = request_irq(priv->irq, migor_ts_isr, IRQF_TRIGGER_LOW, - client->driver_name, priv); + client->name, priv); if (error) { dev_err(&client->dev, "Unable to request touchscreen IRQ.\n"); goto err2; @@ -224,12 +224,19 @@ static int migor_ts_remove(struct i2c_client *client) return 0; } +static const struct i2c_device_id migor_ts_id[] = { + { "migor_ts", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, migor_ts); + static struct i2c_driver migor_ts_driver = { .driver = { .name = "migor_ts", }, .probe = migor_ts_probe, .remove = migor_ts_remove, + .id_table = migor_ts_id, }; static int __init migor_ts_init(void) -- GitLab From 2a5323cd69ff485c1b68960f2b4802cf252558f1 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Mon, 11 Aug 2008 14:59:03 +0900 Subject: [PATCH 106/750] sh: export sh7723 VEU as VEU2H Export sh7723 VEU hardware blocks as VEU2H. The sh7723 VEU2H differs a bit from the sh7722 VEU so use different names for our UIO devices. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt --- arch/sh/kernel/cpu/sh4a/setup-sh7723.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7723.c b/arch/sh/kernel/cpu/sh4a/setup-sh7723.c index cd6baffdc89..a7412cede53 100644 --- a/arch/sh/kernel/cpu/sh4a/setup-sh7723.c +++ b/arch/sh/kernel/cpu/sh4a/setup-sh7723.c @@ -45,7 +45,7 @@ static struct platform_device vpu_device = { }; static struct uio_info veu0_platform_data = { - .name = "VEU", + .name = "VEU2H", .version = "0", .irq = 54, }; @@ -73,7 +73,7 @@ static struct platform_device veu0_device = { }; static struct uio_info veu1_platform_data = { - .name = "VEU", + .name = "VEU2H", .version = "0", .irq = 27, }; -- GitLab From 0c13bf1e7c98668ce69eaedd215ec32f9e1361ae Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Mon, 11 Aug 2008 15:13:24 +0900 Subject: [PATCH 107/750] sh: select memchunk size using kernel cmdline Allow user to pass parameters on kernel command line to override default size for physically contiguous memory buffers. The default VPU buffer size is too small for VGA harware encoding, but instead of just bumping up the number we allow the user to override the default size using the command line. Supports SuperH Mobile hardware blocks such as VEU, VPU and CEU. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt --- arch/sh/mm/consistent.c | 27 +++++++++++++++++++++++++++ 1 file changed, 27 insertions(+) diff --git a/arch/sh/mm/consistent.c b/arch/sh/mm/consistent.c index b2ce014401b..895bb3f335c 100644 --- a/arch/sh/mm/consistent.c +++ b/arch/sh/mm/consistent.c @@ -95,6 +95,29 @@ void dma_cache_sync(struct device *dev, void *vaddr, size_t size, } EXPORT_SYMBOL(dma_cache_sync); +static int __init memchunk_setup(char *str) +{ + return 1; /* accept anything that begins with "memchunk." */ +} +__setup("memchunk.", memchunk_setup); + +static void memchunk_cmdline_override(char *name, unsigned long *sizep) +{ + char *p = boot_command_line; + int k = strlen(name); + + while ((p = strstr(p, "memchunk."))) { + p += 9; /* strlen("memchunk.") */ + if (!strncmp(name, p, k) && p[k] == '=') { + p += k + 1; + *sizep = memparse(p, NULL); + pr_info("%s: forcing memory chunk size to 0x%08lx\n", + name, *sizep); + break; + } + } +} + int platform_resource_setup_memory(struct platform_device *pdev, char *name, unsigned long memsize) { @@ -109,6 +132,10 @@ int platform_resource_setup_memory(struct platform_device *pdev, return -EINVAL; } + memchunk_cmdline_override(name, &memsize); + if (!memsize) + return 0; + buf = dma_alloc_coherent(NULL, memsize, &dma_handle, GFP_KERNEL); if (!buf) { pr_warning("%s: unable to allocate memory\n", name); -- GitLab From ce9c008c8bea25a974d9027b7c6602d535639899 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Mon, 11 Aug 2008 15:26:00 +0900 Subject: [PATCH 108/750] video: export sh_mobile_lcdc panel size Export the LCD panel size for sh_mobile_lcdc boards. This allows us to perform dpi and screen aspect ratio calculations in user space. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt --- arch/sh/boards/board-ap325rxa.c | 4 ++++ arch/sh/boards/mach-migor/setup.c | 8 ++++++++ arch/sh/include/asm/sh_mobile_lcdc.h | 6 ++++++ drivers/video/sh_mobile_lcdcfb.c | 2 ++ 4 files changed, 20 insertions(+) diff --git a/arch/sh/boards/board-ap325rxa.c b/arch/sh/boards/board-ap325rxa.c index 025d4fe55a5..fd1612590bf 100644 --- a/arch/sh/boards/board-ap325rxa.c +++ b/arch/sh/boards/board-ap325rxa.c @@ -140,6 +140,10 @@ static struct sh_mobile_lcdc_info lcdc_info = { .vsync_len = 1, .sync = 0, /* hsync and vsync are active low */ }, + .lcd_size_cfg = { /* 7.0 inch */ + .width = 152, + .height = 91, + }, .board_cfg = { .display_on = ap320_wvga_power_on, }, diff --git a/arch/sh/boards/mach-migor/setup.c b/arch/sh/boards/mach-migor/setup.c index e499ee384d5..714dce91cc9 100644 --- a/arch/sh/boards/mach-migor/setup.c +++ b/arch/sh/boards/mach-migor/setup.c @@ -224,6 +224,10 @@ static struct sh_mobile_lcdc_info sh_mobile_lcdc_info = { .vsync_len = 2, .sync = 0, }, + .lcd_size_cfg = { /* 7.0 inch */ + .width = 152, + .height = 91, + }, } #endif #ifdef CONFIG_SH_MIGOR_QVGA @@ -245,6 +249,10 @@ static struct sh_mobile_lcdc_info sh_mobile_lcdc_info = { .vsync_len = 2, .sync = FB_SYNC_HOR_HIGH_ACT, }, + .lcd_size_cfg = { /* 2.4 inch */ + .width = 49, + .height = 37, + }, .board_cfg = { .setup_sys = migor_lcd_qvga_setup, }, diff --git a/arch/sh/include/asm/sh_mobile_lcdc.h b/arch/sh/include/asm/sh_mobile_lcdc.h index 27677727df4..130102f663f 100644 --- a/arch/sh/include/asm/sh_mobile_lcdc.h +++ b/arch/sh/include/asm/sh_mobile_lcdc.h @@ -47,12 +47,18 @@ struct sh_mobile_lcdc_board_cfg { void (*display_off)(void *board_data); }; +struct sh_mobile_lcdc_lcd_size_cfg { /* width and height of panel in mm */ + unsigned long width; + unsigned long height; +}; + struct sh_mobile_lcdc_chan_cfg { int chan; int bpp; int interface_type; /* selects RGBn or SYSn I/F, see above */ int clock_divider; struct fb_videomode lcd_cfg; + struct sh_mobile_lcdc_lcd_size_cfg lcd_size_cfg; struct sh_mobile_lcdc_board_cfg board_cfg; struct sh_mobile_lcdc_sys_bus_cfg sys_bus_cfg; /* only for SYSn I/F */ }; diff --git a/drivers/video/sh_mobile_lcdcfb.c b/drivers/video/sh_mobile_lcdcfb.c index f6ef6cca73c..4c32c06579a 100644 --- a/drivers/video/sh_mobile_lcdcfb.c +++ b/drivers/video/sh_mobile_lcdcfb.c @@ -595,6 +595,8 @@ static int __init sh_mobile_lcdc_probe(struct platform_device *pdev) info->fbops = &sh_mobile_lcdc_ops; info->var.xres = info->var.xres_virtual = cfg->lcd_cfg.xres; info->var.yres = info->var.yres_virtual = cfg->lcd_cfg.yres; + info->var.width = cfg->lcd_size_cfg.width; + info->var.height = cfg->lcd_size_cfg.height; info->var.activate = FB_ACTIVATE_NOW; error = sh_mobile_lcdc_set_bpp(&info->var, cfg->bpp); if (error) -- GitLab From 74c27c43ebd020fcb65364613503f6c08dc6f535 Mon Sep 17 00:00:00 2001 From: Takashi YOSHII Date: Mon, 11 Aug 2008 20:10:54 +0900 Subject: [PATCH 109/750] binfmt_flat: Stub in a FLAT_PLAT_INIT(). This provides a FLAT_PLAT_INIT() arch hook for platforms that need to set up specific register state prior to calling in to the process, as per ELF_PLAT_INIT(). Signed-off-by: Takashi YOSHII Signed-off-by: Paul Mundt --- fs/binfmt_flat.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/fs/binfmt_flat.c b/fs/binfmt_flat.c index 56372ecf169..dfc0197905c 100644 --- a/fs/binfmt_flat.c +++ b/fs/binfmt_flat.c @@ -914,7 +914,9 @@ static int load_flat_binary(struct linux_binprm * bprm, struct pt_regs * regs) /* Stash our initial stack pointer into the mm structure */ current->mm->start_stack = (unsigned long )sp; - +#ifdef FLAT_PLAT_INIT + FLAT_PLAT_INIT(regs); +#endif DBG_FLT("start_thread(regs=0x%x, entry=0x%x, start_stack=0x%x)\n", (int)regs, (int)start_addr, (int)current->mm->start_stack); -- GitLab From 9b9d6b2a4f6df5544a10de44760755fe757259e5 Mon Sep 17 00:00:00 2001 From: Takashi YOSHII Date: Mon, 11 Aug 2008 20:12:52 +0900 Subject: [PATCH 110/750] sh: Provide a FLAT_PLAT_INIT() definition. SH needs this in order to make sure that r4 has a sane value at process entry time, which the libc expects has already been taken care of. Fixes random crashes in flat binaries. Signed-off-by: Takashi YOSHII Signed-off-by: Paul Mundt --- arch/sh/include/asm/flat.h | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/sh/include/asm/flat.h b/arch/sh/include/asm/flat.h index 0cc800299e0..d3b2b4f109e 100644 --- a/arch/sh/include/asm/flat.h +++ b/arch/sh/include/asm/flat.h @@ -21,4 +21,11 @@ #define flat_get_relocate_addr(rel) (rel) #define flat_set_persistent(relval, p) ({ (void)p; 0; }) +#define FLAT_PLAT_INIT(_r) \ + do { _r->regs[0]=0; _r->regs[1]=0; _r->regs[2]=0; _r->regs[3]=0; \ + _r->regs[4]=0; _r->regs[5]=0; _r->regs[6]=0; _r->regs[7]=0; \ + _r->regs[8]=0; _r->regs[9]=0; _r->regs[10]=0; _r->regs[11]=0; \ + _r->regs[12]=0; _r->regs[13]=0; _r->regs[14]=0; \ + _r->sr = SR_FD; } while (0) + #endif /* __ASM_SH_FLAT_H */ -- GitLab From 3a14a313f9b406c37ab7e3f855b060eb8587b8c7 Mon Sep 17 00:00:00 2001 From: Sven Wegener Date: Sun, 10 Aug 2008 18:24:41 +0000 Subject: [PATCH 111/750] ipvs: Embed estimator object into stats object There's no reason for dynamically allocating an estimator object for every stats object. Directly embed an estimator object into every stats object and switch to using the kernel-provided list implementation. This makes the code much simpler and faster, as we do not need to traverse the list of all estimators to find the one belonging to a stats object. There's no need to use an rwlock, as we only have one reader. Also reorder the members of the estimator structure slightly to avoid padding overhead. This can't be done with the stats object as the members are currently copied to our user space object via memcpy() and changing it would break ABI. Signed-off-by: Sven Wegener Acked-by: Simon Horman --- include/net/ip_vs.h | 28 ++++++++- net/ipv4/ipvs/ip_vs_ctl.c | 2 +- net/ipv4/ipvs/ip_vs_est.c | 117 +++++++++++++------------------------- 3 files changed, 65 insertions(+), 82 deletions(-) diff --git a/include/net/ip_vs.h b/include/net/ip_vs.h index c8ee9b89b02..7312c3dd309 100644 --- a/include/net/ip_vs.h +++ b/include/net/ip_vs.h @@ -140,8 +140,24 @@ struct ip_vs_seq { /* - * IPVS statistics object + * IPVS statistics objects */ +struct ip_vs_estimator { + struct list_head list; + + u64 last_inbytes; + u64 last_outbytes; + u32 last_conns; + u32 last_inpkts; + u32 last_outpkts; + + u32 cps; + u32 inpps; + u32 outpps; + u32 inbps; + u32 outbps; +}; + struct ip_vs_stats { __u32 conns; /* connections scheduled */ @@ -156,7 +172,15 @@ struct ip_vs_stats __u32 inbps; /* current in byte rate */ __u32 outbps; /* current out byte rate */ + /* + * Don't add anything before the lock, because we use memcpy() to copy + * the members before the lock to struct ip_vs_stats_user in + * ip_vs_ctl.c. + */ + spinlock_t lock; /* spin lock */ + + struct ip_vs_estimator est; /* estimator */ }; struct dst_entry; @@ -659,7 +683,7 @@ extern void ip_vs_sync_conn(struct ip_vs_conn *cp); /* * IPVS rate estimator prototypes (from ip_vs_est.c) */ -extern int ip_vs_new_estimator(struct ip_vs_stats *stats); +extern void ip_vs_new_estimator(struct ip_vs_stats *stats); extern void ip_vs_kill_estimator(struct ip_vs_stats *stats); extern void ip_vs_zero_estimator(struct ip_vs_stats *stats); diff --git a/net/ipv4/ipvs/ip_vs_ctl.c b/net/ipv4/ipvs/ip_vs_ctl.c index 999d884e886..d651bce0549 100644 --- a/net/ipv4/ipvs/ip_vs_ctl.c +++ b/net/ipv4/ipvs/ip_vs_ctl.c @@ -684,8 +684,8 @@ ip_vs_zero_stats(struct ip_vs_stats *stats) { spin_lock_bh(&stats->lock); memset(stats, 0, (char *)&stats->lock - (char *)stats); - spin_unlock_bh(&stats->lock); ip_vs_zero_estimator(stats); + spin_unlock_bh(&stats->lock); } /* diff --git a/net/ipv4/ipvs/ip_vs_est.c b/net/ipv4/ipvs/ip_vs_est.c index 1d6e58e502f..5a20f93bd7f 100644 --- a/net/ipv4/ipvs/ip_vs_est.c +++ b/net/ipv4/ipvs/ip_vs_est.c @@ -17,6 +17,7 @@ #include #include #include +#include #include @@ -44,28 +45,11 @@ */ -struct ip_vs_estimator -{ - struct ip_vs_estimator *next; - struct ip_vs_stats *stats; - - u32 last_conns; - u32 last_inpkts; - u32 last_outpkts; - u64 last_inbytes; - u64 last_outbytes; - - u32 cps; - u32 inpps; - u32 outpps; - u32 inbps; - u32 outbps; -}; +static void estimation_timer(unsigned long arg); - -static struct ip_vs_estimator *est_list = NULL; -static DEFINE_RWLOCK(est_lock); -static struct timer_list est_timer; +static LIST_HEAD(est_list); +static DEFINE_SPINLOCK(est_lock); +static DEFINE_TIMER(est_timer, estimation_timer, 0, 0); static void estimation_timer(unsigned long arg) { @@ -76,9 +60,9 @@ static void estimation_timer(unsigned long arg) u64 n_inbytes, n_outbytes; u32 rate; - read_lock(&est_lock); - for (e = est_list; e; e = e->next) { - s = e->stats; + spin_lock(&est_lock); + list_for_each_entry(e, &est_list, list) { + s = container_of(e, struct ip_vs_stats, est); spin_lock(&s->lock); n_conns = s->conns; @@ -114,19 +98,16 @@ static void estimation_timer(unsigned long arg) s->outbps = (e->outbps+0xF)>>5; spin_unlock(&s->lock); } - read_unlock(&est_lock); + spin_unlock(&est_lock); mod_timer(&est_timer, jiffies + 2*HZ); } -int ip_vs_new_estimator(struct ip_vs_stats *stats) +void ip_vs_new_estimator(struct ip_vs_stats *stats) { - struct ip_vs_estimator *est; + struct ip_vs_estimator *est = &stats->est; - est = kzalloc(sizeof(*est), GFP_KERNEL); - if (est == NULL) - return -ENOMEM; + INIT_LIST_HEAD(&est->list); - est->stats = stats; est->last_conns = stats->conns; est->cps = stats->cps<<10; @@ -142,62 +123,40 @@ int ip_vs_new_estimator(struct ip_vs_stats *stats) est->last_outbytes = stats->outbytes; est->outbps = stats->outbps<<5; - write_lock_bh(&est_lock); - est->next = est_list; - if (est->next == NULL) { - setup_timer(&est_timer, estimation_timer, 0); - est_timer.expires = jiffies + 2*HZ; - add_timer(&est_timer); - } - est_list = est; - write_unlock_bh(&est_lock); - return 0; + spin_lock_bh(&est_lock); + if (list_empty(&est_list)) + mod_timer(&est_timer, jiffies + 2 * HZ); + list_add(&est->list, &est_list); + spin_unlock_bh(&est_lock); } void ip_vs_kill_estimator(struct ip_vs_stats *stats) { - struct ip_vs_estimator *est, **pest; - int killed = 0; - - write_lock_bh(&est_lock); - pest = &est_list; - while ((est=*pest) != NULL) { - if (est->stats != stats) { - pest = &est->next; - continue; - } - *pest = est->next; - kfree(est); - killed++; - } - while (killed && !est_list && try_to_del_timer_sync(&est_timer) < 0) { - write_unlock_bh(&est_lock); + struct ip_vs_estimator *est = &stats->est; + + spin_lock_bh(&est_lock); + list_del(&est->list); + while (list_empty(&est_list) && try_to_del_timer_sync(&est_timer) < 0) { + spin_unlock_bh(&est_lock); cpu_relax(); - write_lock_bh(&est_lock); + spin_lock_bh(&est_lock); } - write_unlock_bh(&est_lock); + spin_unlock_bh(&est_lock); } void ip_vs_zero_estimator(struct ip_vs_stats *stats) { - struct ip_vs_estimator *e; - - write_lock_bh(&est_lock); - for (e = est_list; e; e = e->next) { - if (e->stats != stats) - continue; - - /* set counters zero */ - e->last_conns = 0; - e->last_inpkts = 0; - e->last_outpkts = 0; - e->last_inbytes = 0; - e->last_outbytes = 0; - e->cps = 0; - e->inpps = 0; - e->outpps = 0; - e->inbps = 0; - e->outbps = 0; - } - write_unlock_bh(&est_lock); + struct ip_vs_estimator *est = &stats->est; + + /* set counters zero, caller must hold the stats->lock lock */ + est->last_inbytes = 0; + est->last_outbytes = 0; + est->last_conns = 0; + est->last_inpkts = 0; + est->last_outpkts = 0; + est->cps = 0; + est->inpps = 0; + est->outpps = 0; + est->inbps = 0; + est->outbps = 0; } -- GitLab From 519e49e888458649dde453d36c08b7f3432525dc Mon Sep 17 00:00:00 2001 From: Sven Wegener Date: Sun, 10 Aug 2008 18:24:41 +0000 Subject: [PATCH 112/750] ipvs: No need to zero out ip_vs_stats during initialization It's a global variable and automatically initialized to zero. And now we can also initialize the lock at compile time. Signed-off-by: Sven Wegener Acked-by: Simon Horman --- net/ipv4/ipvs/ip_vs_ctl.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/net/ipv4/ipvs/ip_vs_ctl.c b/net/ipv4/ipvs/ip_vs_ctl.c index d651bce0549..cfb1d20993d 100644 --- a/net/ipv4/ipvs/ip_vs_ctl.c +++ b/net/ipv4/ipvs/ip_vs_ctl.c @@ -1784,7 +1784,9 @@ static const struct file_operations ip_vs_info_fops = { #endif -struct ip_vs_stats ip_vs_stats; +struct ip_vs_stats ip_vs_stats = { + .lock = __SPIN_LOCK_UNLOCKED(ip_vs_stats.lock), +}; #ifdef CONFIG_PROC_FS static int ip_vs_stats_show(struct seq_file *seq, void *v) @@ -2333,8 +2335,6 @@ int __init ip_vs_control_init(void) INIT_LIST_HEAD(&ip_vs_rtable[idx]); } - memset(&ip_vs_stats, 0, sizeof(ip_vs_stats)); - spin_lock_init(&ip_vs_stats.lock); ip_vs_new_estimator(&ip_vs_stats); /* Hook the defense timer */ -- GitLab From e93615d0866a974afc7148172f8382e2af48c985 Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Mon, 11 Aug 2008 17:19:14 +1000 Subject: [PATCH 113/750] ipvs: Explictly clear ip_vs_stats members In order to align the coding styles of ip_vs_zero_stats() and its child-function ip_vs_zero_estimator(), clear ip_vs_stats members explicitlty rather than doing a limited memset(). This was chosen over modifying ip_vs_zero_estimator() to use memset() as it is more robust against changes in members in the relevant structures. memset() would be prefered if all members of the structure were to be cleared. Cc: Sven Wegener Signed-off-by: Simon Horman Signed-off-by: Sven Wegener --- net/ipv4/ipvs/ip_vs_ctl.c | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-) diff --git a/net/ipv4/ipvs/ip_vs_ctl.c b/net/ipv4/ipvs/ip_vs_ctl.c index cfb1d20993d..6379705a8dc 100644 --- a/net/ipv4/ipvs/ip_vs_ctl.c +++ b/net/ipv4/ipvs/ip_vs_ctl.c @@ -683,8 +683,21 @@ static void ip_vs_zero_stats(struct ip_vs_stats *stats) { spin_lock_bh(&stats->lock); - memset(stats, 0, (char *)&stats->lock - (char *)stats); + + stats->conns = 0; + stats->inpkts = 0; + stats->outpkts = 0; + stats->inbytes = 0; + stats->outbytes = 0; + + stats->cps = 0; + stats->inpps = 0; + stats->outpps = 0; + stats->inbps = 0; + stats->outbps = 0; + ip_vs_zero_estimator(stats); + spin_unlock_bh(&stats->lock); } -- GitLab From c6ed413ddcfb66e9d3e1318060271391c7659dd3 Mon Sep 17 00:00:00 2001 From: Stephen Rothwell Date: Mon, 11 Aug 2008 14:30:53 -0700 Subject: [PATCH 114/750] sparc/drivers: use linux/of_device.h instead of asm/of_device.h Signed-off-by: Stephen Rothwell Signed-off-by: David S. Miller --- drivers/input/serio/i8042-sparcio.h | 3 ++- drivers/sbus/sbus.c | 2 +- drivers/serial/sunhv.c | 2 +- drivers/serial/sunsab.c | 2 +- drivers/serial/sunsu.c | 2 +- drivers/serial/sunzilog.c | 2 +- 6 files changed, 7 insertions(+), 6 deletions(-) diff --git a/drivers/input/serio/i8042-sparcio.h b/drivers/input/serio/i8042-sparcio.h index 66bafe308b0..692a79ec2a2 100644 --- a/drivers/input/serio/i8042-sparcio.h +++ b/drivers/input/serio/i8042-sparcio.h @@ -1,10 +1,11 @@ #ifndef _I8042_SPARCIO_H #define _I8042_SPARCIO_H +#include + #include #include #include -#include static int i8042_kbd_irq = -1; static int i8042_aux_irq = -1; diff --git a/drivers/sbus/sbus.c b/drivers/sbus/sbus.c index 73a86d09bba..9c129248466 100644 --- a/drivers/sbus/sbus.c +++ b/drivers/sbus/sbus.c @@ -7,13 +7,13 @@ #include #include #include +#include #include #include #include #include #include -#include #include #include diff --git a/drivers/serial/sunhv.c b/drivers/serial/sunhv.c index aeeec5588af..e41766d0803 100644 --- a/drivers/serial/sunhv.c +++ b/drivers/serial/sunhv.c @@ -17,11 +17,11 @@ #include #include #include +#include #include #include #include -#include #include #if defined(CONFIG_MAGIC_SYSRQ) diff --git a/drivers/serial/sunsab.c b/drivers/serial/sunsab.c index 15ee497e1c7..29b4458abf7 100644 --- a/drivers/serial/sunsab.c +++ b/drivers/serial/sunsab.c @@ -32,11 +32,11 @@ #include #include #include +#include #include #include #include -#include #if defined(CONFIG_SERIAL_SUNSAB_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ diff --git a/drivers/serial/sunsu.c b/drivers/serial/sunsu.c index e24e6823508..a378464f929 100644 --- a/drivers/serial/sunsu.c +++ b/drivers/serial/sunsu.c @@ -35,11 +35,11 @@ #include #include #include +#include #include #include #include -#include #if defined(CONFIG_SERIAL_SUNSU_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ diff --git a/drivers/serial/sunzilog.c b/drivers/serial/sunzilog.c index 0f3d69b86d6..3cb4c8aee13 100644 --- a/drivers/serial/sunzilog.c +++ b/drivers/serial/sunzilog.c @@ -32,11 +32,11 @@ #include #endif #include +#include #include #include #include -#include #if defined(CONFIG_SERIAL_SUNZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ -- GitLab From 37cc6780170f6f4fc3f9746d6a9bb2da1d999d7b Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Mon, 11 Aug 2008 14:33:40 -0700 Subject: [PATCH 115/750] ipvs: add lvs-devel as a list contact Signed-off-by: Simon Horman Signed-off-by: David S. Miller --- MAINTAINERS | 1 + 1 file changed, 1 insertion(+) diff --git a/MAINTAINERS b/MAINTAINERS index c67a402a685..45b26e78bbc 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -3071,6 +3071,7 @@ M: horms@verge.net.au P: Julian Anastasov M: ja@ssi.bg L: netdev@vger.kernel.org +L: lvs-devel@vger.kernel.org S: Maintained NFS CLIENT -- GitLab From 9dd1e9eb5cd6f79d4efda57db4e26dfa31ff9ae5 Mon Sep 17 00:00:00 2001 From: Andi Kleen Date: Mon, 11 Aug 2008 23:11:05 +0200 Subject: [PATCH 116/750] x86/PCI: allow scanning of 255 PCI busses Fix an old off by one error in the legacy PCI bus check. 0xff is a valid bus. Signed-off-by: Andi Kleen Signed-off-by: Jesse Barnes --- arch/x86/pci/legacy.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/pci/legacy.c b/arch/x86/pci/legacy.c index ec9ce35e44d..b722dd481b3 100644 --- a/arch/x86/pci/legacy.c +++ b/arch/x86/pci/legacy.c @@ -14,7 +14,7 @@ static void __devinit pcibios_fixup_peer_bridges(void) int n, devfn; long node; - if (pcibios_last_bus <= 0 || pcibios_last_bus >= 0xff) + if (pcibios_last_bus <= 0 || pcibios_last_bus > 0xff) return; DBG("PCI: Peer bridge fixup\n"); -- GitLab From 2c731afb0d4ba16018b400c75665fbdb8feb2175 Mon Sep 17 00:00:00 2001 From: Steve French Date: Mon, 11 Aug 2008 22:28:53 +0000 Subject: [PATCH 117/750] [CIFS] if get root inode fails during mount, cleanup tree connection CC: Stable Kernel Signed-off-by: Steve French --- fs/cifs/cifsfs.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/fs/cifs/cifsfs.c b/fs/cifs/cifsfs.c index e8da4ee761b..f50fc8728c9 100644 --- a/fs/cifs/cifsfs.c +++ b/fs/cifs/cifsfs.c @@ -174,6 +174,8 @@ out_no_root: cERROR(1, ("cifs_read_super: get root inode failed")); if (inode) iput(inode); + + cifs_umount(sb, cifs_sb); out_mount_failed: if (cifs_sb) { -- GitLab From 54b4602d5fe50571362e101138d24edb9cf82d29 Mon Sep 17 00:00:00 2001 From: Steve French Date: Mon, 11 Aug 2008 22:31:40 +0000 Subject: [PATCH 118/750] [CIFS] remove trailing whitespace Signed-off-by: Steve French --- fs/cifs/cifsfs.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/cifs/cifsfs.c b/fs/cifs/cifsfs.c index f50fc8728c9..25ecbd5b040 100644 --- a/fs/cifs/cifsfs.c +++ b/fs/cifs/cifsfs.c @@ -174,7 +174,7 @@ out_no_root: cERROR(1, ("cifs_read_super: get root inode failed")); if (inode) iput(inode); - + cifs_umount(sb, cifs_sb); out_mount_failed: -- GitLab From 1cfa26661a85549063e369e2b40275eeaa7b923c Mon Sep 17 00:00:00 2001 From: Jarek Poplawski Date: Mon, 11 Aug 2008 18:11:06 -0700 Subject: [PATCH 119/750] pkt_sched: Add BH protection for qdisc_stab_lock. Since qdisc_stab_lock is used in qdisc_put_stab(), which is called in BH context from __qdisc_destroy() RCU callback, softirq safe locking is needed. Signed-off-by: Jarek Poplawski Signed-off-by: David S. Miller --- net/sched/sch_api.c | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) diff --git a/net/sched/sch_api.c b/net/sched/sch_api.c index bbf149dd781..c25465e5607 100644 --- a/net/sched/sch_api.c +++ b/net/sched/sch_api.c @@ -331,7 +331,7 @@ static struct qdisc_size_table *qdisc_get_stab(struct nlattr *opt) if (!s || tsize != s->tsize || (!tab && tsize > 0)) return ERR_PTR(-EINVAL); - spin_lock(&qdisc_stab_lock); + spin_lock_bh(&qdisc_stab_lock); list_for_each_entry(stab, &qdisc_stab_list, list) { if (memcmp(&stab->szopts, s, sizeof(*s))) @@ -339,11 +339,11 @@ static struct qdisc_size_table *qdisc_get_stab(struct nlattr *opt) if (tsize > 0 && memcmp(stab->data, tab, tsize * sizeof(u16))) continue; stab->refcnt++; - spin_unlock(&qdisc_stab_lock); + spin_unlock_bh(&qdisc_stab_lock); return stab; } - spin_unlock(&qdisc_stab_lock); + spin_unlock_bh(&qdisc_stab_lock); stab = kmalloc(sizeof(*stab) + tsize * sizeof(u16), GFP_KERNEL); if (!stab) @@ -354,9 +354,9 @@ static struct qdisc_size_table *qdisc_get_stab(struct nlattr *opt) if (tsize > 0) memcpy(stab->data, tab, tsize * sizeof(u16)); - spin_lock(&qdisc_stab_lock); + spin_lock_bh(&qdisc_stab_lock); list_add_tail(&stab->list, &qdisc_stab_list); - spin_unlock(&qdisc_stab_lock); + spin_unlock_bh(&qdisc_stab_lock); return stab; } @@ -366,14 +366,14 @@ void qdisc_put_stab(struct qdisc_size_table *tab) if (!tab) return; - spin_lock(&qdisc_stab_lock); + spin_lock_bh(&qdisc_stab_lock); if (--tab->refcnt == 0) { list_del(&tab->list); kfree(tab); } - spin_unlock(&qdisc_stab_lock); + spin_unlock_bh(&qdisc_stab_lock); } EXPORT_SYMBOL(qdisc_put_stab); -- GitLab From 987c402ac31988f7ecdb38b657bcfeea5831d479 Mon Sep 17 00:00:00 2001 From: Gerrit Renker Date: Mon, 11 Aug 2008 18:17:17 -0700 Subject: [PATCH 120/750] skbuff: Code readability NiT Inserting a space between the `-' improved the C readability (some languages allow hyphens within functions and variable names, which is confusing). Signed-off-by: Gerrit Renker Signed-off-by: David S. Miller --- include/linux/skbuff.h | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/include/linux/skbuff.h b/include/linux/skbuff.h index cfcc45b3bef..358661c9990 100644 --- a/include/linux/skbuff.h +++ b/include/linux/skbuff.h @@ -901,7 +901,7 @@ extern unsigned char *__pskb_pull_tail(struct sk_buff *skb, int delta); static inline unsigned char *__pskb_pull(struct sk_buff *skb, unsigned int len) { if (len > skb_headlen(skb) && - !__pskb_pull_tail(skb, len-skb_headlen(skb))) + !__pskb_pull_tail(skb, len - skb_headlen(skb))) return NULL; skb->len -= len; return skb->data += len; @@ -918,7 +918,7 @@ static inline int pskb_may_pull(struct sk_buff *skb, unsigned int len) return 1; if (unlikely(len > skb->len)) return 0; - return __pskb_pull_tail(skb, len-skb_headlen(skb)) != NULL; + return __pskb_pull_tail(skb, len - skb_headlen(skb)) != NULL; } /** @@ -1321,7 +1321,7 @@ static inline int skb_padto(struct sk_buff *skb, unsigned int len) unsigned int size = skb->len; if (likely(size >= len)) return 0; - return skb_pad(skb, len-size); + return skb_pad(skb, len - size); } static inline int skb_add_data(struct sk_buff *skb, -- GitLab From c7498081a6f5d96c9f3243b6b5e020352903bfd2 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Tue, 12 Aug 2008 02:03:49 -0700 Subject: [PATCH 121/750] sparc64: Fix recursion in stack overflow detection handling. The calls down into prom_printf() when we detect an overflowed stack can recurse again since the overflow stack will be "below" the current kernel stack limit. Prevent this by just returning straight if we are on the stack overflow safe stack already. Signed-off-by: David S. Miller --- arch/sparc64/lib/mcount.S | 17 ++++++++++++++--- 1 file changed, 14 insertions(+), 3 deletions(-) diff --git a/arch/sparc64/lib/mcount.S b/arch/sparc64/lib/mcount.S index 7735a7a6053..734caf0cec0 100644 --- a/arch/sparc64/lib/mcount.S +++ b/arch/sparc64/lib/mcount.S @@ -48,12 +48,23 @@ mcount: sub %g3, STACK_BIAS, %g3 cmp %sp, %g3 bg,pt %xcc, 1f - sethi %hi(panicstring), %g3 + nop + /* If we are already on ovstack, don't hop onto it + * again, we are already trying to output the stack overflow + * message. + */ sethi %hi(ovstack), %g7 ! cant move to panic stack fast enough or %g7, %lo(ovstack), %g7 - add %g7, OVSTACKSIZE, %g7 + add %g7, OVSTACKSIZE, %g3 + sub %g3, STACK_BIAS + 192, %g3 sub %g7, STACK_BIAS, %g7 - mov %g7, %sp + cmp %sp, %g7 + blu,pn %xcc, 2f + cmp %sp, %g3 + bleu,pn %xcc, 1f + nop +2: mov %g3, %sp + sethi %hi(panicstring), %g3 call prom_printf or %g3, %lo(panicstring), %o0 call prom_halt -- GitLab From 67a6e80ede815224db22518cd08350277bbeddb9 Mon Sep 17 00:00:00 2001 From: Ian Molton Date: Sat, 26 Jul 2008 00:51:12 +0100 Subject: [PATCH 122/750] [ARM] eseries: whitespace fixes and cleanup Signed-off-by: Ian Molton --- arch/arm/mach-pxa/eseries.c | 96 ++++++++++++++++++------------------- 1 file changed, 48 insertions(+), 48 deletions(-) diff --git a/arch/arm/mach-pxa/eseries.c b/arch/arm/mach-pxa/eseries.c index 03942450885..112f72926d2 100644 --- a/arch/arm/mach-pxa/eseries.c +++ b/arch/arm/mach-pxa/eseries.c @@ -21,7 +21,7 @@ /* Only e800 has 128MB RAM */ static void __init eseries_fixup(struct machine_desc *desc, - struct tag *tags, char **cmdline, struct meminfo *mi) + struct tag *tags, char **cmdline, struct meminfo *mi) { mi->nr_banks=1; mi->bank[0].start = 0xa0000000; @@ -36,79 +36,79 @@ static void __init eseries_fixup(struct machine_desc *desc, #ifdef CONFIG_MACH_E330 MACHINE_START(E330, "Toshiba e330") - /* Maintainer: Ian Molton (spyro@f2s.com) */ - .phys_io = 0x40000000, - .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, - .boot_params = 0xa0000100, - .map_io = pxa_map_io, - .init_irq = pxa25x_init_irq, - .fixup = eseries_fixup, - .timer = &pxa_timer, + /* Maintainer: Ian Molton (spyro@f2s.com) */ + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa25x_init_irq, + .fixup = eseries_fixup, + .timer = &pxa_timer, MACHINE_END #endif #ifdef CONFIG_MACH_E350 MACHINE_START(E350, "Toshiba e350") /* Maintainer: Ian Molton (spyro@f2s.com) */ - .phys_io = 0x40000000, - .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, - .boot_params = 0xa0000100, - .map_io = pxa_map_io, - .init_irq = pxa25x_init_irq, - .fixup = eseries_fixup, - .timer = &pxa_timer, + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa25x_init_irq, + .fixup = eseries_fixup, + .timer = &pxa_timer, MACHINE_END #endif #ifdef CONFIG_MACH_E740 MACHINE_START(E740, "Toshiba e740") - /* Maintainer: Ian Molton (spyro@f2s.com) */ - .phys_io = 0x40000000, - .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, - .boot_params = 0xa0000100, - .map_io = pxa_map_io, - .init_irq = pxa25x_init_irq, - .fixup = eseries_fixup, - .timer = &pxa_timer, + /* Maintainer: Ian Molton (spyro@f2s.com) */ + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa25x_init_irq, + .fixup = eseries_fixup, + .timer = &pxa_timer, MACHINE_END #endif #ifdef CONFIG_MACH_E750 MACHINE_START(E750, "Toshiba e750") - /* Maintainer: Ian Molton (spyro@f2s.com) */ - .phys_io = 0x40000000, - .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, - .boot_params = 0xa0000100, - .map_io = pxa_map_io, - .init_irq = pxa25x_init_irq, - .fixup = eseries_fixup, - .timer = &pxa_timer, + /* Maintainer: Ian Molton (spyro@f2s.com) */ + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa25x_init_irq, + .fixup = eseries_fixup, + .timer = &pxa_timer, MACHINE_END #endif #ifdef CONFIG_MACH_E400 MACHINE_START(E400, "Toshiba e400") - /* Maintainer: Ian Molton (spyro@f2s.com) */ - .phys_io = 0x40000000, - .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, - .boot_params = 0xa0000100, - .map_io = pxa_map_io, - .init_irq = pxa25x_init_irq, - .fixup = eseries_fixup, - .timer = &pxa_timer, + /* Maintainer: Ian Molton (spyro@f2s.com) */ + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa25x_init_irq, + .fixup = eseries_fixup, + .timer = &pxa_timer, MACHINE_END #endif #ifdef CONFIG_MACH_E800 MACHINE_START(E800, "Toshiba e800") - /* Maintainer: Ian Molton (spyro@f2s.com) */ - .phys_io = 0x40000000, - .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, - .boot_params = 0xa0000100, - .map_io = pxa_map_io, - .init_irq = pxa25x_init_irq, - .fixup = eseries_fixup, - .timer = &pxa_timer, + /* Maintainer: Ian Molton (spyro@f2s.com) */ + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .init_irq = pxa25x_init_irq, + .fixup = eseries_fixup, + .timer = &pxa_timer, MACHINE_END #endif -- GitLab From 5fedd0afd661cf2d387a6eb1b0df78ddbc0c9086 Mon Sep 17 00:00:00 2001 From: Ian Molton Date: Fri, 25 Jul 2008 12:02:31 +0100 Subject: [PATCH 123/750] [ARM] clocklib: Allow dynamic alias creation This patch allows dynamic creation of clock aliases in order to make it possible to have platform independent clock names for use in device drivers. Signed-off-by: Ian Molton --- arch/arm/mach-pxa/clock.c | 25 +++++++++++++++++++++++++ arch/arm/mach-pxa/clock.h | 5 +++++ 2 files changed, 30 insertions(+) diff --git a/arch/arm/mach-pxa/clock.c b/arch/arm/mach-pxa/clock.c index c01eea88f78..ca8e2053815 100644 --- a/arch/arm/mach-pxa/clock.c +++ b/arch/arm/mach-pxa/clock.c @@ -125,3 +125,28 @@ void clks_register(struct clk *clks, size_t num) list_add(&clks[i].node, &clocks); mutex_unlock(&clocks_mutex); } + +int clk_add_alias(char *alias, struct device *alias_dev, char *id, + struct device *dev) +{ + struct clk *r = clk_lookup(dev, id); + struct clk *new; + + if (!r) + return -ENODEV; + + new = kzalloc(sizeof(struct clk), GFP_KERNEL); + + if (!new) + return -ENOMEM; + + new->name = alias; + new->dev = alias_dev; + new->other = r; + + mutex_lock(&clocks_mutex); + list_add(&new->node, &clocks); + mutex_unlock(&clocks_mutex); + + return 0; +} diff --git a/arch/arm/mach-pxa/clock.h b/arch/arm/mach-pxa/clock.h index 1ec8f9178aa..73be795fe3b 100644 --- a/arch/arm/mach-pxa/clock.h +++ b/arch/arm/mach-pxa/clock.h @@ -1,3 +1,5 @@ +#include + struct clk; struct clkops { @@ -86,3 +88,6 @@ extern void clk_pxa3xx_cken_disable(struct clk *); #endif void clks_register(struct clk *clks, size_t num); +int clk_add_alias(char *alias, struct device *alias_dev, char *id, + struct device *dev); + -- GitLab From c1ed406c212973bd59712a0ab722639a75381898 Mon Sep 17 00:00:00 2001 From: Ian Molton Date: Sat, 26 Jul 2008 00:52:36 +0100 Subject: [PATCH 124/750] [ARM] clocklib: Update users of aliases to new API This patch removes the hardcoded alias array from pxa25x.c and reimplements its functionality using the new clock alias call. Signed-off-by: Ian Molton --- arch/arm/mach-pxa/lubbock.c | 2 ++ arch/arm/mach-pxa/pxa25x.c | 10 +--------- 2 files changed, 3 insertions(+), 9 deletions(-) diff --git a/arch/arm/mach-pxa/lubbock.c b/arch/arm/mach-pxa/lubbock.c index bb9e09208b9..4ffdff2d9ff 100644 --- a/arch/arm/mach-pxa/lubbock.c +++ b/arch/arm/mach-pxa/lubbock.c @@ -52,6 +52,7 @@ #include #include "generic.h" +#include "clock.h" #include "devices.h" static unsigned long lubbock_pin_config[] __initdata = { @@ -485,6 +486,7 @@ static void __init lubbock_init(void) pxa2xx_mfp_config(ARRAY_AND_SIZE(lubbock_pin_config)); + clk_add_alias("SA1111_CLK", NULL, "GPIO11_CLK", NULL); pxa_set_udc_info(&udc_info); set_pxa_fb_info(&sharp_lm8v31); pxa_set_mci_info(&lubbock_mci_platform_data); diff --git a/arch/arm/mach-pxa/pxa25x.c b/arch/arm/mach-pxa/pxa25x.c index 9e5d8a8c642..305452b56e9 100644 --- a/arch/arm/mach-pxa/pxa25x.c +++ b/arch/arm/mach-pxa/pxa25x.c @@ -166,8 +166,7 @@ static struct clk pxa25x_hwuart_clk = ; /* - * PXA 2xx clock declarations. Order is important (see aliases below) - * Please be careful not to disrupt the ordering. + * PXA 2xx clock declarations. */ static struct clk pxa25x_clks[] = { INIT_CK("LCDCLK", LCD, &clk_pxa25x_lcd_ops, &pxa_device_fb.dev), @@ -194,11 +193,6 @@ static struct clk pxa25x_clks[] = { INIT_CKEN("FICPCLK", FICP, 47923000, 0, NULL), }; -static struct clk pxa2xx_clk_aliases[] = { - INIT_CKOTHER("GPIO7_CLK", &pxa25x_clks[4], NULL), - INIT_CKOTHER("SA1111_CLK", &pxa25x_clks[5], NULL), -}; - #ifdef CONFIG_PM #define SAVE(x) sleep_save[SLEEP_SAVE_##x] = x @@ -375,8 +369,6 @@ static int __init pxa25x_init(void) if (cpu_is_pxa255()) ret = platform_device_register(&pxa_device_hwuart); - clks_register(pxa2xx_clk_aliases, ARRAY_SIZE(pxa2xx_clk_aliases)); - return ret; } -- GitLab From dec5abe9219aebf6d65e9af95de1c031d7039bdb Mon Sep 17 00:00:00 2001 From: Ian Molton Date: Sat, 9 Aug 2008 21:26:59 +0100 Subject: [PATCH 125/750] [ARM] Fix eseries IRQ limit The max IRQ is too small for all e-series machines which have at least one GPIO expander chip in them. Signed-off-by: Ian Molton --- arch/arm/mach-pxa/include/mach/irqs.h | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/mach-pxa/include/mach/irqs.h b/arch/arm/mach-pxa/include/mach/irqs.h index 32772bc6925..108b5db9b2a 100644 --- a/arch/arm/mach-pxa/include/mach/irqs.h +++ b/arch/arm/mach-pxa/include/mach/irqs.h @@ -183,6 +183,7 @@ defined(CONFIG_MACH_TOSA) || \ defined(CONFIG_MACH_MAINSTONE) || \ defined(CONFIG_MACH_PCM027) || \ + defined(CONFIG_ARCH_PXA_ESERIES) || \ defined(CONFIG_MACH_MAGICIAN) #define NR_IRQS (IRQ_BOARD_END) #elif defined(CONFIG_MACH_ZYLONITE) -- GitLab From 2836548826b4187ba770b14d36bc40d52a76b49c Mon Sep 17 00:00:00 2001 From: Ian Molton Date: Sat, 9 Aug 2008 21:48:45 +0100 Subject: [PATCH 126/750] [ARM] e740 config use MFP This patch updates e740 to use the new MFP GPIO setup code. Signed-off-by: Ian Molton --- arch/arm/mach-pxa/eseries.c | 50 ++++++++++++++++++++++++++++++++++++- 1 file changed, 49 insertions(+), 1 deletion(-) diff --git a/arch/arm/mach-pxa/eseries.c b/arch/arm/mach-pxa/eseries.c index 112f72926d2..d2700999251 100644 --- a/arch/arm/mach-pxa/eseries.c +++ b/arch/arm/mach-pxa/eseries.c @@ -10,15 +10,57 @@ * */ +#include #include #include #include -#include #include +#include +#include + #include "generic.h" +static unsigned long e740_pin_config[] __initdata = { + /* Chip selects */ + GPIO15_nCS_1, /* CS1 - Flash */ + GPIO79_nCS_3, /* CS3 - IMAGEON */ + GPIO80_nCS_4, /* CS4 - TMIO */ + + /* Clocks */ + GPIO12_32KHz, + + /* BTUART */ + GPIO42_BTUART_RXD, + GPIO43_BTUART_TXD, + GPIO44_BTUART_CTS, + GPIO45_GPIO, /* Used by TMIO for #SUSPEND */ + + /* PC Card */ + GPIO8_GPIO, /* CD0 */ + GPIO44_GPIO, /* CD1 */ + GPIO11_GPIO, /* IRQ0 */ + GPIO6_GPIO, /* IRQ1 */ + GPIO27_GPIO, /* RST0 */ + GPIO24_GPIO, /* RST1 */ + GPIO20_GPIO, /* PWR0 */ + GPIO23_GPIO, /* PWR1 */ + GPIO48_nPOE, + GPIO49_nPWE, + GPIO50_nPIOR, + GPIO51_nPIOW, + GPIO52_nPCE_1, + GPIO53_nPCE_2, + GPIO54_nPSKTSEL, + GPIO55_nPREG, + GPIO56_nPWAIT, + GPIO57_nIOIS16, + + /* wakeup */ + GPIO0_GPIO | WAKEUP_ON_EDGE_RISE, +}; + /* Only e800 has 128MB RAM */ static void __init eseries_fixup(struct machine_desc *desc, struct tag *tags, char **cmdline, struct meminfo *mi) @@ -32,6 +74,11 @@ static void __init eseries_fixup(struct machine_desc *desc, mi->bank[0].size = (64*1024*1024); } +static void __init e740_init(void) +{ + pxa2xx_mfp_config(ARRAY_AND_SIZE(e740_pin_config)); +} + /* e-series machine definitions */ #ifdef CONFIG_MACH_E330 @@ -69,6 +116,7 @@ MACHINE_START(E740, "Toshiba e740") .map_io = pxa_map_io, .init_irq = pxa25x_init_irq, .fixup = eseries_fixup, + .init_machine = e740_init, .timer = &pxa_timer, MACHINE_END #endif -- GitLab From 908cbc10135755ea055feaa6a8ec209edfe489be Mon Sep 17 00:00:00 2001 From: Ian Molton Date: Sat, 9 Aug 2008 21:50:28 +0100 Subject: [PATCH 127/750] [ARM] e400 config use MFP This patch updates e400 to use the new MFP GPIO setup code. Signed-off-by: Ian Molton --- arch/arm/mach-pxa/eseries.c | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/arch/arm/mach-pxa/eseries.c b/arch/arm/mach-pxa/eseries.c index d2700999251..001a252bd51 100644 --- a/arch/arm/mach-pxa/eseries.c +++ b/arch/arm/mach-pxa/eseries.c @@ -61,6 +61,24 @@ static unsigned long e740_pin_config[] __initdata = { GPIO0_GPIO | WAKEUP_ON_EDGE_RISE, }; +static unsigned long e400_pin_config[] __initdata = { + /* Chip selects */ + GPIO15_nCS_1, /* CS1 - Flash */ + GPIO80_nCS_4, /* CS4 - TMIO */ + + /* Clocks */ + GPIO12_32KHz, + + /* BTUART */ + GPIO42_BTUART_RXD, + GPIO43_BTUART_TXD, + GPIO44_BTUART_CTS, + GPIO45_GPIO, /* Used by TMIO for #SUSPEND */ + + /* wakeup */ + GPIO0_GPIO | WAKEUP_ON_EDGE_RISE, +}; + /* Only e800 has 128MB RAM */ static void __init eseries_fixup(struct machine_desc *desc, struct tag *tags, char **cmdline, struct meminfo *mi) @@ -79,6 +97,11 @@ static void __init e740_init(void) pxa2xx_mfp_config(ARRAY_AND_SIZE(e740_pin_config)); } +static void __init e400_init(void) +{ + pxa2xx_mfp_config(ARRAY_AND_SIZE(e400_pin_config)); +} + /* e-series machine definitions */ #ifdef CONFIG_MACH_E330 @@ -143,6 +166,7 @@ MACHINE_START(E400, "Toshiba e400") .map_io = pxa_map_io, .init_irq = pxa25x_init_irq, .fixup = eseries_fixup, + .init_machine = e400_init, .timer = &pxa_timer, MACHINE_END #endif -- GitLab From f64c0accea433a83261afb81193412146cc0e569 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Fri, 8 Aug 2008 23:14:58 +0100 Subject: [PATCH 128/750] [ARM] 5183/2: Provide Poodle LoCoMo GPIO names Fix Poodle ASoC compilation by providing Poodle LoCoMo GPIO names. Cc: Richard Purdie Cc: Mark Brown Signed-off-by: Dmitry Baryshkov Signed-off-by: Russell King --- arch/arm/mach-pxa/include/mach/poodle.h | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/mach-pxa/include/mach/poodle.h b/arch/arm/mach-pxa/include/mach/poodle.h index 8956afe8195..67debc47e8c 100644 --- a/arch/arm/mach-pxa/include/mach/poodle.h +++ b/arch/arm/mach-pxa/include/mach/poodle.h @@ -70,6 +70,12 @@ #define POODLE_SCOOP_IO_DIR ( POODLE_SCOOP_VPEN | POODLE_SCOOP_HS_OUT ) #define POODLE_SCOOP_IO_OUT ( 0 ) +#define POODLE_LOCOMO_GPIO_AMP_ON LOCOMO_GPIO(8) +#define POODLE_LOCOMO_GPIO_MUTE_L LOCOMO_GPIO(10) +#define POODLE_LOCOMO_GPIO_MUTE_R LOCOMO_GPIO(11) +#define POODLE_LOCOMO_GPIO_232VCC_ON LOCOMO_GPIO(12) +#define POODLE_LOCOMO_GPIO_JK_B LOCOMO_GPIO(13) + extern struct platform_device poodle_locomo_device; #endif /* __ASM_ARCH_POODLE_H */ -- GitLab From b03a5b7559563dafdbe52f8b5d8e453a914db941 Mon Sep 17 00:00:00 2001 From: Russell King Date: Mon, 11 Aug 2008 12:27:16 +0100 Subject: [PATCH 129/750] [ARM] traps: don't call undef hook functions with spinlock held Calling the undefined instruction handler functions with a spinlock held is a recipe for must_sleep() warnings. Avoid it. Signed-off-by: Russell King --- arch/arm/kernel/traps.c | 31 ++++++++++++++++++------------- 1 file changed, 18 insertions(+), 13 deletions(-) diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c index 7277aef8309..872f1f8fbb5 100644 --- a/arch/arm/kernel/traps.c +++ b/arch/arm/kernel/traps.c @@ -288,14 +288,28 @@ void unregister_undef_hook(struct undef_hook *hook) spin_unlock_irqrestore(&undef_lock, flags); } +static int call_undef_hook(struct pt_regs *regs, unsigned int instr) +{ + struct undef_hook *hook; + unsigned long flags; + int (*fn)(struct pt_regs *regs, unsigned int instr) = NULL; + + spin_lock_irqsave(&undef_lock, flags); + list_for_each_entry(hook, &undef_hook, node) + if ((instr & hook->instr_mask) == hook->instr_val && + (regs->ARM_cpsr & hook->cpsr_mask) == hook->cpsr_val) + fn = hook->fn; + spin_unlock_irqrestore(&undef_lock, flags); + + return fn ? fn(regs, instr) : 1; +} + asmlinkage void __exception do_undefinstr(struct pt_regs *regs) { unsigned int correction = thumb_mode(regs) ? 2 : 4; unsigned int instr; - struct undef_hook *hook; siginfo_t info; void __user *pc; - unsigned long flags; /* * According to the ARM ARM, PC is 2 or 4 bytes ahead, @@ -325,17 +339,8 @@ asmlinkage void __exception do_undefinstr(struct pt_regs *regs) } #endif - spin_lock_irqsave(&undef_lock, flags); - list_for_each_entry(hook, &undef_hook, node) { - if ((instr & hook->instr_mask) == hook->instr_val && - (regs->ARM_cpsr & hook->cpsr_mask) == hook->cpsr_val) { - if (hook->fn(regs, instr) == 0) { - spin_unlock_irqrestore(&undef_lock, flags); - return; - } - } - } - spin_unlock_irqrestore(&undef_lock, flags); + if (call_undef_hook(regs, instr) == 0) + return; #ifdef CONFIG_DEBUG_USER if (user_debug & UDBG_UNDEFINED) { -- GitLab From 751a8ae95d7ab951104bd1bb643e4b8c8ee5fc4d Mon Sep 17 00:00:00 2001 From: Stefan Schmidt Date: Tue, 12 Aug 2008 11:15:02 +0100 Subject: [PATCH 130/750] [ARM] 5193/1: Wire up missing syscalls Setup some missing syscall pointed out by the checksyscalls.sh script. Fix two small whitespace issues while being there. Signed-off-by: Stefan Schmidt Signed-off-by: Russell King --- arch/arm/include/asm/unistd.h | 6 ++++++ arch/arm/kernel/calls.S | 10 ++++++++-- 2 files changed, 14 insertions(+), 2 deletions(-) diff --git a/arch/arm/include/asm/unistd.h b/arch/arm/include/asm/unistd.h index f95fbb2fcb5..010618487cf 100644 --- a/arch/arm/include/asm/unistd.h +++ b/arch/arm/include/asm/unistd.h @@ -381,6 +381,12 @@ #define __NR_fallocate (__NR_SYSCALL_BASE+352) #define __NR_timerfd_settime (__NR_SYSCALL_BASE+353) #define __NR_timerfd_gettime (__NR_SYSCALL_BASE+354) +#define __NR_signalfd4 (__NR_SYSCALL_BASE+355) +#define __NR_eventfd2 (__NR_SYSCALL_BASE+356) +#define __NR_epoll_create1 (__NR_SYSCALL_BASE+357) +#define __NR_dup3 (__NR_SYSCALL_BASE+358) +#define __NR_pipe2 (__NR_SYSCALL_BASE+359) +#define __NR_inotify_init1 (__NR_SYSCALL_BASE+360) /* * The following SWIs are ARM private. diff --git a/arch/arm/kernel/calls.S b/arch/arm/kernel/calls.S index 30a67a5a40a..09a061cb783 100644 --- a/arch/arm/kernel/calls.S +++ b/arch/arm/kernel/calls.S @@ -262,10 +262,10 @@ /* 250 */ CALL(sys_epoll_create) CALL(ABI(sys_epoll_ctl, sys_oabi_epoll_ctl)) CALL(ABI(sys_epoll_wait, sys_oabi_epoll_wait)) - CALL(sys_remap_file_pages) + CALL(sys_remap_file_pages) CALL(sys_ni_syscall) /* sys_set_thread_area */ /* 255 */ CALL(sys_ni_syscall) /* sys_get_thread_area */ - CALL(sys_set_tid_address) + CALL(sys_set_tid_address) CALL(sys_timer_create) CALL(sys_timer_settime) CALL(sys_timer_gettime) @@ -364,6 +364,12 @@ CALL(sys_fallocate) CALL(sys_timerfd_settime) CALL(sys_timerfd_gettime) +/* 355 */ CALL(sys_signalfd4) + CALL(sys_eventfd2) + CALL(sys_epoll_create1) + CALL(sys_dup3) + CALL(sys_pipe2) +/* 360 */ CALL(sys_inotify_init1) #ifndef syscalls_counted .equ syscalls_padding, ((NR_syscalls + 3) & ~3) - NR_syscalls #define syscalls_counted -- GitLab From 61db7fb1c78c32b6abdc5c7965981de332aeaa5b Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Tue, 12 Aug 2008 00:04:15 +0100 Subject: [PATCH 131/750] [ARM] 5192/1: ARM TLB: add v7wbi_{possible,always}_flags to {possible,always}_tlb_flags Commit 2ccdd1e77da52ad494e9af46bf272d816830cb28 doesn't add v7wbi_possible_flags and v7wbi_always_flags to possible_tlb_flags and always_tlb_flags. This causes the L2 cache flush in clean_pmd_entry() (intended for Feroceon only) to execute on ARMv7, and the CPU hangs. This patch is required for OMAP3 boards to boot. Signed-off-by: Paul Walmsley Acked-by: Lennert Buytenhek Signed-off-by: Russell King --- arch/arm/include/asm/tlbflush.h | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) diff --git a/arch/arm/include/asm/tlbflush.h b/arch/arm/include/asm/tlbflush.h index 0d0d40f1b59..b543a054a17 100644 --- a/arch/arm/include/asm/tlbflush.h +++ b/arch/arm/include/asm/tlbflush.h @@ -54,6 +54,7 @@ * v4wbi - ARMv4 with write buffer with I TLB flush entry instruction * fr - Feroceon (v4wbi with non-outer-cacheable page table walks) * v6wbi - ARMv6 with write buffer with I TLB flush entry instruction + * v7wbi - identical to v6wbi */ #undef _TLB #undef MULTI_TLB @@ -266,14 +267,16 @@ extern struct cpu_tlb_fns cpu_tlb; v4wbi_possible_flags | \ fr_possible_flags | \ v4wb_possible_flags | \ - v6wbi_possible_flags) + v6wbi_possible_flags | \ + v7wbi_possible_flags) #define always_tlb_flags (v3_always_flags & \ v4_always_flags & \ v4wbi_always_flags & \ fr_always_flags & \ v4wb_always_flags & \ - v6wbi_always_flags) + v6wbi_always_flags & \ + v7wbi_always_flags) #define tlb_flag(f) ((always_tlb_flags & (f)) || (__tlb_flag & possible_tlb_flags & (f))) -- GitLab From 8a5544c887a8682e39c94061c58180e9c44b050b Mon Sep 17 00:00:00 2001 From: Russell King Date: Tue, 12 Aug 2008 14:02:23 +0100 Subject: [PATCH 132/750] [ARM] add proc-macros.S include to proc-arm940 and proc-arm946 ... otherwise these fail to build. Signed-off-by: Russell King --- arch/arm/mm/proc-arm940.S | 1 + arch/arm/mm/proc-arm946.S | 1 + 2 files changed, 2 insertions(+) diff --git a/arch/arm/mm/proc-arm940.S b/arch/arm/mm/proc-arm940.S index 1a3d63df8e9..551244d5ca1 100644 --- a/arch/arm/mm/proc-arm940.S +++ b/arch/arm/mm/proc-arm940.S @@ -15,6 +15,7 @@ #include #include #include +#include "proc-macros.S" /* ARM940T has a 4KB DCache comprising 256 lines of 4 words */ #define CACHE_DLINESIZE 16 diff --git a/arch/arm/mm/proc-arm946.S b/arch/arm/mm/proc-arm946.S index 82d579ac9b9..6168c6160de 100644 --- a/arch/arm/mm/proc-arm946.S +++ b/arch/arm/mm/proc-arm946.S @@ -17,6 +17,7 @@ #include #include #include +#include "proc-macros.S" /* * ARM946E-S is synthesizable to have 0KB to 1MB sized D-Cache, -- GitLab From da1562af624cbf17935c7fded51466bb1a1b63a8 Mon Sep 17 00:00:00 2001 From: Nicolas Pitre Date: Tue, 12 Aug 2008 17:13:19 +0100 Subject: [PATCH 133/750] [ARM] 5194/1: update .gitignore Signed-off-by: Nicolas Pitre Signed-off-by: Russell King --- arch/arm/boot/compressed/.gitignore | 3 ++- arch/arm/kernel/.gitignore | 1 + 2 files changed, 3 insertions(+), 1 deletion(-) create mode 100644 arch/arm/kernel/.gitignore diff --git a/arch/arm/boot/compressed/.gitignore b/arch/arm/boot/compressed/.gitignore index b15f927a592..ab204db594d 100644 --- a/arch/arm/boot/compressed/.gitignore +++ b/arch/arm/boot/compressed/.gitignore @@ -1,2 +1,3 @@ -piggy.gz font.c +piggy.gz +vmlinux.lds diff --git a/arch/arm/kernel/.gitignore b/arch/arm/kernel/.gitignore new file mode 100644 index 00000000000..c5f676c3c22 --- /dev/null +++ b/arch/arm/kernel/.gitignore @@ -0,0 +1 @@ +vmlinux.lds -- GitLab From e34456825de0d3ac4c4e8fe0bdc6b599404ea06f Mon Sep 17 00:00:00 2001 From: Stephen Rothwell Date: Tue, 12 Aug 2008 17:45:23 -0700 Subject: [PATCH 134/750] sparc: remove include of linux/of_device.h from asm/of_device.h Now that all the direct includes of asm/of_device.h are gone, this is safe to do. Signed-off-by: Stephen Rothwell Signed-off-by: David S. Miller --- arch/sparc/include/asm/of_device.h | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/arch/sparc/include/asm/of_device.h b/arch/sparc/include/asm/of_device.h index e5f5aedc229..bba777a416d 100644 --- a/arch/sparc/include/asm/of_device.h +++ b/arch/sparc/include/asm/of_device.h @@ -30,8 +30,7 @@ struct of_device extern void __iomem *of_ioremap(struct resource *res, unsigned long offset, unsigned long size, char *name); extern void of_iounmap(struct resource *res, void __iomem *base, unsigned long size); -/* These are just here during the transition */ -#include +/* This is just here during the transition */ #include #endif /* __KERNEL__ */ -- GitLab From 4f70f7a91bffdcc39f088748dc678953eb9a3fbd Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Tue, 12 Aug 2008 18:33:56 -0700 Subject: [PATCH 135/750] sparc64: Implement IRQ stacks. Signed-off-by: David S. Miller --- arch/sparc/include/asm/irq_64.h | 4 +++ arch/sparc64/kernel/irq.c | 52 ++++++++++++++++++++++++++++ arch/sparc64/kernel/kstack.h | 58 ++++++++++++++++++++++++++++++++ arch/sparc64/kernel/process.c | 27 ++++----------- arch/sparc64/kernel/stacktrace.c | 10 +++--- arch/sparc64/kernel/traps.c | 7 ++-- arch/sparc64/lib/mcount.S | 22 ++++++++++++ arch/sparc64/mm/init.c | 11 ++++++ 8 files changed, 161 insertions(+), 30 deletions(-) create mode 100644 arch/sparc64/kernel/kstack.h diff --git a/arch/sparc/include/asm/irq_64.h b/arch/sparc/include/asm/irq_64.h index 3473e25231d..e3dd9303643 100644 --- a/arch/sparc/include/asm/irq_64.h +++ b/arch/sparc/include/asm/irq_64.h @@ -93,4 +93,8 @@ static inline unsigned long get_softint(void) void __trigger_all_cpu_backtrace(void); #define trigger_all_cpu_backtrace() __trigger_all_cpu_backtrace() +extern void *hardirq_stack[NR_CPUS]; +extern void *softirq_stack[NR_CPUS]; +#define __ARCH_HAS_DO_SOFTIRQ + #endif diff --git a/arch/sparc64/kernel/irq.c b/arch/sparc64/kernel/irq.c index ba43d85e8dd..9b6689d9d57 100644 --- a/arch/sparc64/kernel/irq.c +++ b/arch/sparc64/kernel/irq.c @@ -682,10 +682,32 @@ void ack_bad_irq(unsigned int virt_irq) ino, virt_irq); } +void *hardirq_stack[NR_CPUS]; +void *softirq_stack[NR_CPUS]; + +static __attribute__((always_inline)) void *set_hardirq_stack(void) +{ + void *orig_sp, *sp = hardirq_stack[smp_processor_id()]; + + __asm__ __volatile__("mov %%sp, %0" : "=r" (orig_sp)); + if (orig_sp < sp || + orig_sp > (sp + THREAD_SIZE)) { + sp += THREAD_SIZE - 192 - STACK_BIAS; + __asm__ __volatile__("mov %0, %%sp" : : "r" (sp)); + } + + return orig_sp; +} +static __attribute__((always_inline)) void restore_hardirq_stack(void *orig_sp) +{ + __asm__ __volatile__("mov %0, %%sp" : : "r" (orig_sp)); +} + void handler_irq(int irq, struct pt_regs *regs) { unsigned long pstate, bucket_pa; struct pt_regs *old_regs; + void *orig_sp; clear_softint(1 << irq); @@ -703,6 +725,8 @@ void handler_irq(int irq, struct pt_regs *regs) "i" (PSTATE_IE) : "memory"); + orig_sp = set_hardirq_stack(); + while (bucket_pa) { struct irq_desc *desc; unsigned long next_pa; @@ -719,10 +743,38 @@ void handler_irq(int irq, struct pt_regs *regs) bucket_pa = next_pa; } + restore_hardirq_stack(orig_sp); + irq_exit(); set_irq_regs(old_regs); } +void do_softirq(void) +{ + unsigned long flags; + + if (in_interrupt()) + return; + + local_irq_save(flags); + + if (local_softirq_pending()) { + void *orig_sp, *sp = softirq_stack[smp_processor_id()]; + + sp += THREAD_SIZE - 192 - STACK_BIAS; + + __asm__ __volatile__("mov %%sp, %0\n\t" + "mov %1, %%sp" + : "=&r" (orig_sp) + : "r" (sp)); + __do_softirq(); + __asm__ __volatile__("mov %0, %%sp" + : : "r" (orig_sp)); + } + + local_irq_restore(flags); +} + #ifdef CONFIG_HOTPLUG_CPU void fixup_irqs(void) { diff --git a/arch/sparc64/kernel/kstack.h b/arch/sparc64/kernel/kstack.h new file mode 100644 index 00000000000..43909d5680e --- /dev/null +++ b/arch/sparc64/kernel/kstack.h @@ -0,0 +1,58 @@ +#ifndef _KSTACK_H +#define _KSTACK_H + +#include +#include +#include +#include + +/* SP must be STACK_BIAS adjusted already. */ +static inline bool kstack_valid(struct thread_info *tp, unsigned long sp) +{ + unsigned long base = (unsigned long) tp; + + if (sp >= (base + sizeof(struct thread_info)) && + sp <= (base + THREAD_SIZE - sizeof(struct sparc_stackf))) + return true; + + base = (unsigned long) hardirq_stack[tp->cpu]; + if (sp >= base && + sp <= (base + THREAD_SIZE - sizeof(struct sparc_stackf))) + return true; + base = (unsigned long) softirq_stack[tp->cpu]; + if (sp >= base && + sp <= (base + THREAD_SIZE - sizeof(struct sparc_stackf))) + return true; + + return false; +} + +/* Does "regs" point to a valid pt_regs trap frame? */ +static inline bool kstack_is_trap_frame(struct thread_info *tp, struct pt_regs *regs) +{ + unsigned long base = (unsigned long) tp; + unsigned long addr = (unsigned long) regs; + + if (addr >= base && + addr <= (base + THREAD_SIZE - sizeof(*regs))) + goto check_magic; + + base = (unsigned long) hardirq_stack[tp->cpu]; + if (addr >= base && + addr <= (base + THREAD_SIZE - sizeof(*regs))) + goto check_magic; + base = (unsigned long) softirq_stack[tp->cpu]; + if (addr >= base && + addr <= (base + THREAD_SIZE - sizeof(*regs))) + goto check_magic; + + return false; + +check_magic: + if ((regs->magic & ~0x1ff) == PT_REGS_MAGIC) + return true; + return false; + +} + +#endif /* _KSTACK_H */ diff --git a/arch/sparc64/kernel/process.c b/arch/sparc64/kernel/process.c index 7f5debdc5fe..15f4178592e 100644 --- a/arch/sparc64/kernel/process.c +++ b/arch/sparc64/kernel/process.c @@ -52,6 +52,8 @@ #include #include +#include "kstack.h" + static void sparc64_yield(int cpu) { if (tlb_type != hypervisor) @@ -235,19 +237,6 @@ void show_regs(struct pt_regs *regs) struct global_reg_snapshot global_reg_snapshot[NR_CPUS]; static DEFINE_SPINLOCK(global_reg_snapshot_lock); -static bool kstack_valid(struct thread_info *tp, struct reg_window *rw) -{ - unsigned long thread_base, fp; - - thread_base = (unsigned long) tp; - fp = (unsigned long) rw; - - if (fp < (thread_base + sizeof(struct thread_info)) || - fp >= (thread_base + THREAD_SIZE)) - return false; - return true; -} - static void __global_reg_self(struct thread_info *tp, struct pt_regs *regs, int this_cpu) { @@ -264,11 +253,11 @@ static void __global_reg_self(struct thread_info *tp, struct pt_regs *regs, rw = (struct reg_window *) (regs->u_regs[UREG_FP] + STACK_BIAS); - if (kstack_valid(tp, rw)) { + if (kstack_valid(tp, (unsigned long) rw)) { global_reg_snapshot[this_cpu].i7 = rw->ins[7]; rw = (struct reg_window *) (rw->ins[6] + STACK_BIAS); - if (kstack_valid(tp, rw)) + if (kstack_valid(tp, (unsigned long) rw)) global_reg_snapshot[this_cpu].rpc = rw->ins[7]; } } else { @@ -828,7 +817,7 @@ out: unsigned long get_wchan(struct task_struct *task) { unsigned long pc, fp, bias = 0; - unsigned long thread_info_base; + struct thread_info *tp; struct reg_window *rw; unsigned long ret = 0; int count = 0; @@ -837,14 +826,12 @@ unsigned long get_wchan(struct task_struct *task) task->state == TASK_RUNNING) goto out; - thread_info_base = (unsigned long) task_stack_page(task); + tp = task_thread_info(task); bias = STACK_BIAS; fp = task_thread_info(task)->ksp + bias; do { - /* Bogus frame pointer? */ - if (fp < (thread_info_base + sizeof(struct thread_info)) || - fp >= (thread_info_base + THREAD_SIZE)) + if (!kstack_valid(tp, fp)) break; rw = (struct reg_window *) fp; pc = rw->ins[7]; diff --git a/arch/sparc64/kernel/stacktrace.c b/arch/sparc64/kernel/stacktrace.c index e9d7f0660f2..237e7f8a40a 100644 --- a/arch/sparc64/kernel/stacktrace.c +++ b/arch/sparc64/kernel/stacktrace.c @@ -5,6 +5,8 @@ #include #include +#include "kstack.h" + void save_stack_trace(struct stack_trace *trace) { unsigned long ksp, fp, thread_base; @@ -24,17 +26,13 @@ void save_stack_trace(struct stack_trace *trace) struct pt_regs *regs; unsigned long pc; - /* Bogus frame pointer? */ - if (fp < (thread_base + sizeof(struct thread_info)) || - fp > (thread_base + THREAD_SIZE - sizeof(struct sparc_stackf))) + if (!kstack_valid(tp, fp)) break; sf = (struct sparc_stackf *) fp; regs = (struct pt_regs *) (sf + 1); - if (((unsigned long)regs <= - (thread_base + THREAD_SIZE - sizeof(*regs))) && - (regs->magic & ~0x1ff) == PT_REGS_MAGIC) { + if (kstack_is_trap_frame(tp, regs)) { if (!(regs->tstate & TSTATE_PRIV)) break; pc = regs->tpc; diff --git a/arch/sparc64/kernel/traps.c b/arch/sparc64/kernel/traps.c index 404e8561e2d..3d924121c79 100644 --- a/arch/sparc64/kernel/traps.c +++ b/arch/sparc64/kernel/traps.c @@ -39,6 +39,7 @@ #include #include "entry.h" +#include "kstack.h" /* When an irrecoverable trap occurs at tl > 0, the trap entry * code logs the trap state registers at every level in the trap @@ -2115,14 +2116,12 @@ void show_stack(struct task_struct *tsk, unsigned long *_ksp) struct pt_regs *regs; unsigned long pc; - /* Bogus frame pointer? */ - if (fp < (thread_base + sizeof(struct thread_info)) || - fp >= (thread_base + THREAD_SIZE)) + if (!kstack_valid(tp, fp)) break; sf = (struct sparc_stackf *) fp; regs = (struct pt_regs *) (sf + 1); - if ((regs->magic & ~0x1ff) == PT_REGS_MAGIC) { + if (kstack_is_trap_frame(tp, regs)) { if (!(regs->tstate & TSTATE_PRIV)) break; pc = regs->tpc; diff --git a/arch/sparc64/lib/mcount.S b/arch/sparc64/lib/mcount.S index 734caf0cec0..fad90ddb3a2 100644 --- a/arch/sparc64/lib/mcount.S +++ b/arch/sparc64/lib/mcount.S @@ -49,6 +49,28 @@ mcount: cmp %sp, %g3 bg,pt %xcc, 1f nop + lduh [%g6 + TI_CPU], %g1 + sethi %hi(hardirq_stack), %g3 + or %g3, %lo(hardirq_stack), %g3 + sllx %g1, 3, %g1 + ldx [%g3 + %g1], %g7 + sub %g7, STACK_BIAS, %g7 + cmp %sp, %g7 + bleu,pt %xcc, 2f + sethi %hi(THREAD_SIZE), %g3 + add %g7, %g3, %g7 + cmp %sp, %g7 + blu,pn %xcc, 1f +2: sethi %hi(softirq_stack), %g3 + or %g3, %lo(softirq_stack), %g3 + ldx [%g3 + %g1], %g7 + cmp %sp, %g7 + bleu,pt %xcc, 2f + sethi %hi(THREAD_SIZE), %g3 + add %g7, %g3, %g7 + cmp %sp, %g7 + blu,pn %xcc, 1f + nop /* If we are already on ovstack, don't hop onto it * again, we are already trying to output the stack overflow * message. diff --git a/arch/sparc64/mm/init.c b/arch/sparc64/mm/init.c index 4e821b3ecb0..217de3ea29e 100644 --- a/arch/sparc64/mm/init.c +++ b/arch/sparc64/mm/init.c @@ -49,6 +49,7 @@ #include #include #include +#include #define MAX_PHYS_ADDRESS (1UL << 42UL) #define KPTE_BITMAP_CHUNK_SZ (256UL * 1024UL * 1024UL) @@ -1771,6 +1772,16 @@ void __init paging_init(void) if (tlb_type == hypervisor) sun4v_mdesc_init(); + /* Once the OF device tree and MDESC have been setup, we know + * the list of possible cpus. Therefore we can allocate the + * IRQ stacks. + */ + for_each_possible_cpu(i) { + /* XXX Use node local allocations... XXX */ + softirq_stack[i] = __va(lmb_alloc(THREAD_SIZE, THREAD_SIZE)); + hardirq_stack[i] = __va(lmb_alloc(THREAD_SIZE, THREAD_SIZE)); + } + /* Setup bootmem... */ last_valid_pfn = end_pfn = bootmem_init(phys_base); -- GitLab From d9dd421fd6ed17af55d27c8d93a9f561be0ff50f Mon Sep 17 00:00:00 2001 From: Jeremy Kerr Date: Wed, 13 Aug 2008 11:29:31 +1000 Subject: [PATCH 136/750] powerpc/spufs: fix npc setting for NOSCHED contexts Currently, spu_run ignores the npc argument for contexts created with SPU_CREATE_NOSCHED. While this is correct for isolated contexts, there's no need to enforce the npc restriction on non-isolated NOSCHED contexts. This means that NOSCHED contexts can only ever run with an entry point of 0x0. This change to spu_run_init allows setting of the npc (and, while we're at it, the privcntl) for non-isolated NOSCHED contexts. This allows us to run NOSCHED contexts from any entry point. Signed-off-by: Jeremy Kerr --- arch/powerpc/platforms/cell/spufs/run.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-) diff --git a/arch/powerpc/platforms/cell/spufs/run.c b/arch/powerpc/platforms/cell/spufs/run.c index f7edba6cb79..c9bb7cfd3dc 100644 --- a/arch/powerpc/platforms/cell/spufs/run.c +++ b/arch/powerpc/platforms/cell/spufs/run.c @@ -206,11 +206,6 @@ static int spu_run_init(struct spu_context *ctx, u32 *npc) (SPU_RUNCNTL_RUNNABLE | SPU_RUNCNTL_ISOLATE); if (runcntl == 0) runcntl = SPU_RUNCNTL_RUNNABLE; - } - - if (ctx->flags & SPU_CREATE_NOSCHED) { - spuctx_switch_state(ctx, SPU_UTIL_USER); - ctx->ops->runcntl_write(ctx, runcntl); } else { unsigned long privcntl; @@ -219,9 +214,15 @@ static int spu_run_init(struct spu_context *ctx, u32 *npc) else privcntl = SPU_PRIVCNTL_MODE_NORMAL; - ctx->ops->npc_write(ctx, *npc); ctx->ops->privcntl_write(ctx, privcntl); - ctx->ops->runcntl_write(ctx, runcntl); + ctx->ops->npc_write(ctx, *npc); + } + + ctx->ops->runcntl_write(ctx, runcntl); + + if (ctx->flags & SPU_CREATE_NOSCHED) { + spuctx_switch_state(ctx, SPU_UTIL_USER); + } else { if (ctx->state == SPU_STATE_SAVED) { ret = spu_activate(ctx, 0); -- GitLab From 79071eb0b2f142b9cc6531d04fa2915943938b5e Mon Sep 17 00:00:00 2001 From: David Chinner Date: Wed, 13 Aug 2008 15:41:12 +1000 Subject: [PATCH 137/750] [XFS] Use the generic bitops rather than implementing them ourselves. This keeps xfs_lowbit64 as it was since there aren't good generic helpers there ... Patch inspired by Andi Kleen. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31472a Signed-off-by: David Chinner Signed-off-by: Eric Sandeen Signed-off-by: Donald Douwsma Signed-off-by: Lachlan McIlroy --- fs/xfs/xfs_bit.c | 103 ------------------------------------------- fs/xfs/xfs_bit.h | 34 ++++++++++++-- fs/xfs/xfs_rtalloc.c | 19 +++----- 3 files changed, 37 insertions(+), 119 deletions(-) diff --git a/fs/xfs/xfs_bit.c b/fs/xfs/xfs_bit.c index fab0b6d5a41..48228848f5a 100644 --- a/fs/xfs/xfs_bit.c +++ b/fs/xfs/xfs_bit.c @@ -25,109 +25,6 @@ * XFS bit manipulation routines, used in non-realtime code. */ -#ifndef HAVE_ARCH_HIGHBIT -/* - * Index of high bit number in byte, -1 for none set, 0..7 otherwise. - */ -static const char xfs_highbit[256] = { - -1, 0, 1, 1, 2, 2, 2, 2, /* 00 .. 07 */ - 3, 3, 3, 3, 3, 3, 3, 3, /* 08 .. 0f */ - 4, 4, 4, 4, 4, 4, 4, 4, /* 10 .. 17 */ - 4, 4, 4, 4, 4, 4, 4, 4, /* 18 .. 1f */ - 5, 5, 5, 5, 5, 5, 5, 5, /* 20 .. 27 */ - 5, 5, 5, 5, 5, 5, 5, 5, /* 28 .. 2f */ - 5, 5, 5, 5, 5, 5, 5, 5, /* 30 .. 37 */ - 5, 5, 5, 5, 5, 5, 5, 5, /* 38 .. 3f */ - 6, 6, 6, 6, 6, 6, 6, 6, /* 40 .. 47 */ - 6, 6, 6, 6, 6, 6, 6, 6, /* 48 .. 4f */ - 6, 6, 6, 6, 6, 6, 6, 6, /* 50 .. 57 */ - 6, 6, 6, 6, 6, 6, 6, 6, /* 58 .. 5f */ - 6, 6, 6, 6, 6, 6, 6, 6, /* 60 .. 67 */ - 6, 6, 6, 6, 6, 6, 6, 6, /* 68 .. 6f */ - 6, 6, 6, 6, 6, 6, 6, 6, /* 70 .. 77 */ - 6, 6, 6, 6, 6, 6, 6, 6, /* 78 .. 7f */ - 7, 7, 7, 7, 7, 7, 7, 7, /* 80 .. 87 */ - 7, 7, 7, 7, 7, 7, 7, 7, /* 88 .. 8f */ - 7, 7, 7, 7, 7, 7, 7, 7, /* 90 .. 97 */ - 7, 7, 7, 7, 7, 7, 7, 7, /* 98 .. 9f */ - 7, 7, 7, 7, 7, 7, 7, 7, /* a0 .. a7 */ - 7, 7, 7, 7, 7, 7, 7, 7, /* a8 .. af */ - 7, 7, 7, 7, 7, 7, 7, 7, /* b0 .. b7 */ - 7, 7, 7, 7, 7, 7, 7, 7, /* b8 .. bf */ - 7, 7, 7, 7, 7, 7, 7, 7, /* c0 .. c7 */ - 7, 7, 7, 7, 7, 7, 7, 7, /* c8 .. cf */ - 7, 7, 7, 7, 7, 7, 7, 7, /* d0 .. d7 */ - 7, 7, 7, 7, 7, 7, 7, 7, /* d8 .. df */ - 7, 7, 7, 7, 7, 7, 7, 7, /* e0 .. e7 */ - 7, 7, 7, 7, 7, 7, 7, 7, /* e8 .. ef */ - 7, 7, 7, 7, 7, 7, 7, 7, /* f0 .. f7 */ - 7, 7, 7, 7, 7, 7, 7, 7, /* f8 .. ff */ -}; -#endif - -/* - * xfs_highbit32: get high bit set out of 32-bit argument, -1 if none set. - */ -inline int -xfs_highbit32( - __uint32_t v) -{ -#ifdef HAVE_ARCH_HIGHBIT - return highbit32(v); -#else - int i; - - if (v & 0xffff0000) - if (v & 0xff000000) - i = 24; - else - i = 16; - else if (v & 0x0000ffff) - if (v & 0x0000ff00) - i = 8; - else - i = 0; - else - return -1; - return i + xfs_highbit[(v >> i) & 0xff]; -#endif -} - -/* - * xfs_lowbit64: get low bit set out of 64-bit argument, -1 if none set. - */ -int -xfs_lowbit64( - __uint64_t v) -{ - __uint32_t w = (__uint32_t)v; - int n = 0; - - if (w) { /* lower bits */ - n = ffs(w); - } else { /* upper bits */ - w = (__uint32_t)(v >> 32); - if (w && (n = ffs(w))) - n += 32; - } - return n - 1; -} - -/* - * xfs_highbit64: get high bit set out of 64-bit argument, -1 if none set. - */ -int -xfs_highbit64( - __uint64_t v) -{ - __uint32_t h = (__uint32_t)(v >> 32); - - if (h) - return xfs_highbit32(h) + 32; - return xfs_highbit32((__uint32_t)v); -} - - /* * Return whether bitmap is empty. * Size is number of words in the bitmap, which is padded to word boundary diff --git a/fs/xfs/xfs_bit.h b/fs/xfs/xfs_bit.h index 082641a9782..8e0e463dae2 100644 --- a/fs/xfs/xfs_bit.h +++ b/fs/xfs/xfs_bit.h @@ -47,13 +47,39 @@ static inline __uint64_t xfs_mask64lo(int n) } /* Get high bit set out of 32-bit argument, -1 if none set */ -extern int xfs_highbit32(__uint32_t v); +static inline int xfs_highbit32(__uint32_t v) +{ + return fls(v) - 1; +} + +/* Get high bit set out of 64-bit argument, -1 if none set */ +static inline int xfs_highbit64(__uint64_t v) +{ + return fls64(v) - 1; +} + +/* Get low bit set out of 32-bit argument, -1 if none set */ +static inline int xfs_lowbit32(__uint32_t v) +{ + unsigned long t = v; + return (v) ? find_first_bit(&t, 32) : -1; +} /* Get low bit set out of 64-bit argument, -1 if none set */ -extern int xfs_lowbit64(__uint64_t v); +static inline int xfs_lowbit64(__uint64_t v) +{ + __uint32_t w = (__uint32_t)v; + int n = 0; -/* Get high bit set out of 64-bit argument, -1 if none set */ -extern int xfs_highbit64(__uint64_t); + if (w) { /* lower bits */ + n = ffs(w); + } else { /* upper bits */ + w = (__uint32_t)(v >> 32); + if (w && (n = ffs(w))) + n += 32; + } + return n - 1; +} /* Return whether bitmap is empty (1 == empty) */ extern int xfs_bitmap_empty(uint *map, uint size); diff --git a/fs/xfs/xfs_rtalloc.c b/fs/xfs/xfs_rtalloc.c index bf87a591350..e2f68de1615 100644 --- a/fs/xfs/xfs_rtalloc.c +++ b/fs/xfs/xfs_rtalloc.c @@ -73,18 +73,6 @@ STATIC int xfs_rtmodify_summary(xfs_mount_t *, xfs_trans_t *, int, * Internal functions. */ -/* - * xfs_lowbit32: get low bit set out of 32-bit argument, -1 if none set. - */ -STATIC int -xfs_lowbit32( - __uint32_t v) -{ - if (v) - return ffs(v) - 1; - return -1; -} - /* * Allocate space to the bitmap or summary file, and zero it, for growfs. */ @@ -450,6 +438,7 @@ xfs_rtallocate_extent_near( } bbno = XFS_BITTOBLOCK(mp, bno); i = 0; + ASSERT(minlen != 0); log2len = xfs_highbit32(minlen); /* * Loop over all bitmap blocks (bbno + i is current block). @@ -618,6 +607,8 @@ xfs_rtallocate_extent_size( xfs_suminfo_t sum; /* summary information for extents */ ASSERT(minlen % prod == 0 && maxlen % prod == 0); + ASSERT(maxlen != 0); + /* * Loop over all the levels starting with maxlen. * At each level, look at all the bitmap blocks, to see if there @@ -675,6 +666,9 @@ xfs_rtallocate_extent_size( *rtblock = NULLRTBLOCK; return 0; } + ASSERT(minlen != 0); + ASSERT(maxlen != 0); + /* * Loop over sizes, from maxlen down to minlen. * This time, when we do the allocations, allow smaller ones @@ -1961,6 +1955,7 @@ xfs_growfs_rt( nsbp->sb_blocksize * nsbp->sb_rextsize); nsbp->sb_rextents = nsbp->sb_rblocks; do_div(nsbp->sb_rextents, nsbp->sb_rextsize); + ASSERT(nsbp->sb_rextents != 0); nsbp->sb_rextslog = xfs_highbit32(nsbp->sb_rextents); nrsumlevels = nmp->m_rsumlevels = nsbp->sb_rextslog + 1; nrsumsize = -- GitLab From 3790689fa3c771bba6bafb7dee3e8389dd0b55bc Mon Sep 17 00:00:00 2001 From: Lachlan McIlroy Date: Wed, 13 Aug 2008 15:42:10 +1000 Subject: [PATCH 138/750] [XFS] Do not access buffers after dropping reference count We should not access a buffer after dropping it's reference count otherwise we could race with another thread that releases the final reference count and frees the buffer causing us to access potentially unmapped memory. The bug this change fixes only occured on DEBUG XFS since the offending code was in an ASSERT. SGI-PV: 984429 SGI-Modid: xfs-linux-melb:xfs-kern:31715a Signed-off-by: Lachlan McIlroy Signed-off-by: David Chinner --- fs/xfs/linux-2.6/xfs_buf.c | 6 +----- 1 file changed, 1 insertion(+), 5 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_buf.c b/fs/xfs/linux-2.6/xfs_buf.c index 9cc8f021309..9f45c74f1a8 100644 --- a/fs/xfs/linux-2.6/xfs_buf.c +++ b/fs/xfs/linux-2.6/xfs_buf.c @@ -838,6 +838,7 @@ xfs_buf_rele( return; } + ASSERT(atomic_read(&bp->b_hold) > 0); if (atomic_dec_and_lock(&bp->b_hold, &hash->bh_lock)) { if (bp->b_relse) { atomic_inc(&bp->b_hold); @@ -851,11 +852,6 @@ xfs_buf_rele( spin_unlock(&hash->bh_lock); xfs_buf_free(bp); } - } else { - /* - * Catch reference count leaks - */ - ASSERT(atomic_read(&bp->b_hold) >= 0); } } -- GitLab From 016516462575d28fab3354f762cad16c86c09116 Mon Sep 17 00:00:00 2001 From: David Chinner Date: Wed, 13 Aug 2008 15:45:15 +1000 Subject: [PATCH 139/750] [XFS] Avoid directly referencing the VFS inode. In several places we directly convert from the XFS inode to the linux (VFS) inode by a simple deference of ip->i_vnode. We should not do this - a helper function should be used to extract the VFS inode from the XFS inode. Introduce the function VFS_I() to extract the VFS inode from the XFS inode. The name was chosen to match XFS_I() which is used to extract the XFS inode from the VFS inode. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31720a Signed-off-by: David Chinner Signed-off-by: Niv Sardi Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_export.c | 6 +++--- fs/xfs/linux-2.6/xfs_fs_subr.c | 6 +++--- fs/xfs/linux-2.6/xfs_iops.c | 14 +++++++------- fs/xfs/linux-2.6/xfs_iops.h | 6 ------ fs/xfs/linux-2.6/xfs_lrw.c | 2 +- fs/xfs/linux-2.6/xfs_super.c | 4 ++-- fs/xfs/xfs_iget.c | 7 ++++--- fs/xfs/xfs_inode.h | 22 +++++++++++++++++++--- fs/xfs/xfs_utils.c | 4 ++-- 9 files changed, 41 insertions(+), 30 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_export.c b/fs/xfs/linux-2.6/xfs_export.c index 987fe84f7b1..d3880b7c147 100644 --- a/fs/xfs/linux-2.6/xfs_export.c +++ b/fs/xfs/linux-2.6/xfs_export.c @@ -139,7 +139,7 @@ xfs_nfs_get_inode( } xfs_iunlock(ip, XFS_ILOCK_SHARED); - return ip->i_vnode; + return VFS_I(ip); } STATIC struct dentry * @@ -219,9 +219,9 @@ xfs_fs_get_parent( if (unlikely(error)) return ERR_PTR(-error); - parent = d_alloc_anon(cip->i_vnode); + parent = d_alloc_anon(VFS_I(cip)); if (unlikely(!parent)) { - iput(cip->i_vnode); + iput(VFS_I(cip)); return ERR_PTR(-ENOMEM); } return parent; diff --git a/fs/xfs/linux-2.6/xfs_fs_subr.c b/fs/xfs/linux-2.6/xfs_fs_subr.c index 1eefe61f0e1..36caa6d957d 100644 --- a/fs/xfs/linux-2.6/xfs_fs_subr.c +++ b/fs/xfs/linux-2.6/xfs_fs_subr.c @@ -31,7 +31,7 @@ xfs_tosspages( xfs_off_t last, int fiopt) { - struct address_space *mapping = ip->i_vnode->i_mapping; + struct address_space *mapping = VFS_I(ip)->i_mapping; if (mapping->nrpages) truncate_inode_pages(mapping, first); @@ -44,7 +44,7 @@ xfs_flushinval_pages( xfs_off_t last, int fiopt) { - struct address_space *mapping = ip->i_vnode->i_mapping; + struct address_space *mapping = VFS_I(ip)->i_mapping; int ret = 0; if (mapping->nrpages) { @@ -64,7 +64,7 @@ xfs_flush_pages( uint64_t flags, int fiopt) { - struct address_space *mapping = ip->i_vnode->i_mapping; + struct address_space *mapping = VFS_I(ip)->i_mapping; int ret = 0; int ret2; diff --git a/fs/xfs/linux-2.6/xfs_iops.c b/fs/xfs/linux-2.6/xfs_iops.c index e88f5102808..fec5ff5a2f1 100644 --- a/fs/xfs/linux-2.6/xfs_iops.c +++ b/fs/xfs/linux-2.6/xfs_iops.c @@ -62,7 +62,7 @@ void xfs_synchronize_atime( xfs_inode_t *ip) { - struct inode *inode = ip->i_vnode; + struct inode *inode = VFS_I(ip); if (inode) { ip->i_d.di_atime.t_sec = (__int32_t)inode->i_atime.tv_sec; @@ -79,7 +79,7 @@ void xfs_mark_inode_dirty_sync( xfs_inode_t *ip) { - struct inode *inode = ip->i_vnode; + struct inode *inode = VFS_I(ip); if (inode) mark_inode_dirty_sync(inode); @@ -299,7 +299,7 @@ xfs_vn_mknod( if (unlikely(error)) goto out_free_acl; - inode = ip->i_vnode; + inode = VFS_I(ip); error = xfs_init_security(inode, dir); if (unlikely(error)) @@ -366,7 +366,7 @@ xfs_vn_lookup( return NULL; } - return d_splice_alias(cip->i_vnode, dentry); + return d_splice_alias(VFS_I(cip), dentry); } STATIC struct dentry * @@ -399,12 +399,12 @@ xfs_vn_ci_lookup( /* if exact match, just splice and exit */ if (!ci_name.name) - return d_splice_alias(ip->i_vnode, dentry); + return d_splice_alias(VFS_I(ip), dentry); /* else case-insensitive match... */ dname.name = ci_name.name; dname.len = ci_name.len; - dentry = d_add_ci(ip->i_vnode, dentry, &dname); + dentry = d_add_ci(VFS_I(ip), dentry, &dname); kmem_free(ci_name.name); return dentry; } @@ -478,7 +478,7 @@ xfs_vn_symlink( if (unlikely(error)) goto out; - inode = cip->i_vnode; + inode = VFS_I(cip); error = xfs_init_security(inode, dir); if (unlikely(error)) diff --git a/fs/xfs/linux-2.6/xfs_iops.h b/fs/xfs/linux-2.6/xfs_iops.h index d97ba934a2a..fdda404bc34 100644 --- a/fs/xfs/linux-2.6/xfs_iops.h +++ b/fs/xfs/linux-2.6/xfs_iops.h @@ -33,10 +33,4 @@ struct xfs_inode; extern void xfs_ichgtime(struct xfs_inode *, int); extern void xfs_ichgtime_fast(struct xfs_inode *, struct inode *, int); -#define xfs_vtoi(vp) \ - ((struct xfs_inode *)vn_to_inode(vp)->i_private) - -#define XFS_I(inode) \ - ((struct xfs_inode *)(inode)->i_private) - #endif /* __XFS_IOPS_H__ */ diff --git a/fs/xfs/linux-2.6/xfs_lrw.c b/fs/xfs/linux-2.6/xfs_lrw.c index 82333b3e118..e03e2c3789b 100644 --- a/fs/xfs/linux-2.6/xfs_lrw.c +++ b/fs/xfs/linux-2.6/xfs_lrw.c @@ -137,7 +137,7 @@ xfs_iozero( struct address_space *mapping; int status; - mapping = ip->i_vnode->i_mapping; + mapping = VFS_I(ip)->i_mapping; do { unsigned offset, bytes; void *fsdata; diff --git a/fs/xfs/linux-2.6/xfs_super.c b/fs/xfs/linux-2.6/xfs_super.c index 30ae96397e3..b49722940d6 100644 --- a/fs/xfs/linux-2.6/xfs_super.c +++ b/fs/xfs/linux-2.6/xfs_super.c @@ -1106,7 +1106,7 @@ void xfs_flush_inode( xfs_inode_t *ip) { - struct inode *inode = ip->i_vnode; + struct inode *inode = VFS_I(ip); igrab(inode); xfs_syncd_queue_work(ip->i_mount, inode, xfs_flush_inode_work); @@ -1825,7 +1825,7 @@ xfs_fs_fill_super( sb->s_time_gran = 1; set_posix_acl_flag(sb); - root = igrab(mp->m_rootip->i_vnode); + root = igrab(VFS_I(mp->m_rootip)); if (!root) { error = ENOENT; goto fail_unmount; diff --git a/fs/xfs/xfs_iget.c b/fs/xfs/xfs_iget.c index b07604b94d9..d44342640ca 100644 --- a/fs/xfs/xfs_iget.c +++ b/fs/xfs/xfs_iget.c @@ -411,10 +411,11 @@ xfs_iput(xfs_inode_t *ip, * Special iput for brand-new inodes that are still locked */ void -xfs_iput_new(xfs_inode_t *ip, - uint lock_flags) +xfs_iput_new( + xfs_inode_t *ip, + uint lock_flags) { - struct inode *inode = ip->i_vnode; + struct inode *inode = VFS_I(ip); xfs_itrace_entry(ip); diff --git a/fs/xfs/xfs_inode.h b/fs/xfs/xfs_inode.h index 17a04b6321e..4a5e48c8ded 100644 --- a/fs/xfs/xfs_inode.h +++ b/fs/xfs/xfs_inode.h @@ -263,6 +263,25 @@ typedef struct xfs_inode { #define XFS_ISIZE(ip) (((ip)->i_d.di_mode & S_IFMT) == S_IFREG) ? \ (ip)->i_size : (ip)->i_d.di_size; +/* Convert from vfs inode to xfs inode */ +static inline struct xfs_inode *XFS_I(struct inode *inode) +{ + return (struct xfs_inode *)inode->i_private; +} + +static inline struct xfs_inode *xfs_vtoi(bhv_vnode_t *vp) +{ + return XFS_I((struct inode *)vp); +} + +/* convert from xfs inode to vfs inode */ +static inline struct inode *VFS_I(struct xfs_inode *ip) +{ + return (struct inode *)ip->i_vnode; +} +#define XFS_ITOV(ip) VFS_I(ip) +#define XFS_ITOV_NULL(ip) VFS_I(ip) + /* * i_flags helper functions */ @@ -439,9 +458,6 @@ xfs_iflags_test_and_clear(xfs_inode_t *ip, unsigned short flags) #define XFS_ITRUNC_DEFINITE 0x1 #define XFS_ITRUNC_MAYBE 0x2 -#define XFS_ITOV(ip) ((ip)->i_vnode) -#define XFS_ITOV_NULL(ip) ((ip)->i_vnode) - /* * For multiple groups support: if S_ISGID bit is set in the parent * directory, group of new file is set to that of the parent, and diff --git a/fs/xfs/xfs_utils.c b/fs/xfs/xfs_utils.c index 98e5f110ba5..35d4d414bcc 100644 --- a/fs/xfs/xfs_utils.c +++ b/fs/xfs/xfs_utils.c @@ -237,7 +237,7 @@ xfs_droplink( ASSERT (ip->i_d.di_nlink > 0); ip->i_d.di_nlink--; - drop_nlink(ip->i_vnode); + drop_nlink(VFS_I(ip)); xfs_trans_log_inode(tp, ip, XFS_ILOG_CORE); error = 0; @@ -301,7 +301,7 @@ xfs_bumplink( ASSERT(ip->i_d.di_nlink > 0); ip->i_d.di_nlink++; - inc_nlink(ip->i_vnode); + inc_nlink(VFS_I(ip)); if ((ip->i_d.di_version == XFS_DINODE_VERSION_1) && (ip->i_d.di_nlink > XFS_MAXLINK_1)) { /* -- GitLab From 705db4a24e0576f30d736de3c49623b4686ce473 Mon Sep 17 00:00:00 2001 From: David Chinner Date: Wed, 13 Aug 2008 15:47:43 +1000 Subject: [PATCH 140/750] [XFS] kill shouty XFS_ITOV_NULL macro Replace XFS_ITOV_NULL() with the new VFS_I() inline. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31722a Signed-off-by: David Chinner Signed-off-by: Niv Sardi Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_vnode.c | 2 +- fs/xfs/quota/xfs_qm_syscalls.c | 2 +- fs/xfs/xfs_inode.c | 4 ++-- fs/xfs/xfs_inode.h | 1 - fs/xfs/xfs_vfsops.c | 2 +- fs/xfs/xfs_vnodeops.c | 2 +- 6 files changed, 6 insertions(+), 7 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_vnode.c b/fs/xfs/linux-2.6/xfs_vnode.c index 25488b6d988..1e39d04c86c 100644 --- a/fs/xfs/linux-2.6/xfs_vnode.c +++ b/fs/xfs/linux-2.6/xfs_vnode.c @@ -108,7 +108,7 @@ vn_hold( */ static inline int xfs_icount(struct xfs_inode *ip) { - bhv_vnode_t *vp = XFS_ITOV_NULL(ip); + bhv_vnode_t *vp = VFS_I(ip); if (vp) return vn_count(vp); diff --git a/fs/xfs/quota/xfs_qm_syscalls.c b/fs/xfs/quota/xfs_qm_syscalls.c index adfb8723f65..132a0abb2f0 100644 --- a/fs/xfs/quota/xfs_qm_syscalls.c +++ b/fs/xfs/quota/xfs_qm_syscalls.c @@ -1059,7 +1059,7 @@ again: ip = ip->i_mnext; continue; } - vp = XFS_ITOV_NULL(ip); + vp = VFS_I(ip); if (!vp) { ASSERT(ip->i_udquot == NULL); ASSERT(ip->i_gdquot == NULL); diff --git a/fs/xfs/xfs_inode.c b/fs/xfs/xfs_inode.c index bedc6616317..46cecba0992 100644 --- a/fs/xfs/xfs_inode.c +++ b/fs/xfs/xfs_inode.c @@ -1077,7 +1077,7 @@ xfs_ialloc( } ASSERT(ip != NULL); - vp = XFS_ITOV(ip); + vp = VFS_I(ip); ip->i_d.di_mode = (__uint16_t)mode; ip->i_d.di_onlink = 0; ip->i_d.di_nlink = nlink; @@ -3480,7 +3480,7 @@ xfs_iflush_all( continue; } - vp = XFS_ITOV_NULL(ip); + vp = VFS_I(ip); if (!vp) { XFS_MOUNT_IUNLOCK(mp); xfs_finish_reclaim(ip, 0, XFS_IFLUSH_ASYNC); diff --git a/fs/xfs/xfs_inode.h b/fs/xfs/xfs_inode.h index 4a5e48c8ded..f04e026f6e0 100644 --- a/fs/xfs/xfs_inode.h +++ b/fs/xfs/xfs_inode.h @@ -280,7 +280,6 @@ static inline struct inode *VFS_I(struct xfs_inode *ip) return (struct inode *)ip->i_vnode; } #define XFS_ITOV(ip) VFS_I(ip) -#define XFS_ITOV_NULL(ip) VFS_I(ip) /* * i_flags helper functions diff --git a/fs/xfs/xfs_vfsops.c b/fs/xfs/xfs_vfsops.c index 4a9a43315a8..5f461ce4441 100644 --- a/fs/xfs/xfs_vfsops.c +++ b/fs/xfs/xfs_vfsops.c @@ -404,7 +404,7 @@ xfs_sync_inodes( continue; } - vp = XFS_ITOV_NULL(ip); + vp = VFS_I(ip); /* * If the vnode is gone then this is being torn down, diff --git a/fs/xfs/xfs_vnodeops.c b/fs/xfs/xfs_vnodeops.c index 76a1166af82..a2e470ae259 100644 --- a/fs/xfs/xfs_vnodeops.c +++ b/fs/xfs/xfs_vnodeops.c @@ -2933,7 +2933,7 @@ xfs_finish_reclaim( int sync_mode) { xfs_perag_t *pag = xfs_get_perag(ip->i_mount, ip->i_ino); - bhv_vnode_t *vp = XFS_ITOV_NULL(ip); + bhv_vnode_t *vp = VFS_I(ip); if (vp && VN_BAD(vp)) goto reclaim; -- GitLab From e4f7529108d01bf66af8ebecd6be2b98d8db30ce Mon Sep 17 00:00:00 2001 From: David Chinner Date: Wed, 13 Aug 2008 16:00:45 +1000 Subject: [PATCH 141/750] [XFS] Kill shouty XFS_ITOV() macro Replace XFS_ITOV() with the new VFS_I() inline. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31724a Signed-off-by: David Chinner Signed-off-by: Niv Sardi Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_ioctl.c | 4 ++-- fs/xfs/linux-2.6/xfs_iops.c | 2 +- fs/xfs/linux-2.6/xfs_linux.h | 2 +- fs/xfs/linux-2.6/xfs_super.c | 2 +- fs/xfs/quota/xfs_dquot.c | 2 +- fs/xfs/xfs_bmap.c | 2 +- fs/xfs/xfs_dfrag.c | 4 ++-- fs/xfs/xfs_inode.c | 2 +- fs/xfs/xfs_inode.h | 1 - fs/xfs/xfs_itable.c | 2 +- fs/xfs/xfs_utils.h | 4 ++-- fs/xfs/xfs_vfsops.c | 8 ++++---- fs/xfs/xfs_vnodeops.c | 12 ++++++------ 13 files changed, 23 insertions(+), 24 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_ioctl.c b/fs/xfs/linux-2.6/xfs_ioctl.c index acb978d9d08..48799ba7e3e 100644 --- a/fs/xfs/linux-2.6/xfs_ioctl.c +++ b/fs/xfs/linux-2.6/xfs_ioctl.c @@ -245,7 +245,7 @@ xfs_vget_fsop_handlereq( xfs_iunlock(ip, XFS_ILOCK_SHARED); - *inode = XFS_ITOV(ip); + *inode = VFS_I(ip); return 0; } @@ -927,7 +927,7 @@ STATIC void xfs_diflags_to_linux( struct xfs_inode *ip) { - struct inode *inode = XFS_ITOV(ip); + struct inode *inode = VFS_I(ip); unsigned int xflags = xfs_ip2xflags(ip); if (xflags & XFS_XFLAG_IMMUTABLE) diff --git a/fs/xfs/linux-2.6/xfs_iops.c b/fs/xfs/linux-2.6/xfs_iops.c index fec5ff5a2f1..cc0f21af48f 100644 --- a/fs/xfs/linux-2.6/xfs_iops.c +++ b/fs/xfs/linux-2.6/xfs_iops.c @@ -101,7 +101,7 @@ xfs_ichgtime( xfs_inode_t *ip, int flags) { - struct inode *inode = vn_to_inode(XFS_ITOV(ip)); + struct inode *inode = VFS_I(ip); timespec_t tv; nanotime(&tv); diff --git a/fs/xfs/linux-2.6/xfs_linux.h b/fs/xfs/linux-2.6/xfs_linux.h index 4d45d9351a6..a9cd6e41052 100644 --- a/fs/xfs/linux-2.6/xfs_linux.h +++ b/fs/xfs/linux-2.6/xfs_linux.h @@ -180,7 +180,7 @@ #define xfs_sort(a,n,s,fn) sort(a,n,s,fn,NULL) #define xfs_stack_trace() dump_stack() #define xfs_itruncate_data(ip, off) \ - (-vmtruncate(vn_to_inode(XFS_ITOV(ip)), (off))) + (-vmtruncate(vn_to_inode(VFS_I(ip)), (off))) /* Move the kernel do_div definition off to one side */ diff --git a/fs/xfs/linux-2.6/xfs_super.c b/fs/xfs/linux-2.6/xfs_super.c index b49722940d6..c9ec44a02e2 100644 --- a/fs/xfs/linux-2.6/xfs_super.c +++ b/fs/xfs/linux-2.6/xfs_super.c @@ -1131,7 +1131,7 @@ void xfs_flush_device( xfs_inode_t *ip) { - struct inode *inode = vn_to_inode(XFS_ITOV(ip)); + struct inode *inode = VFS_I(ip); igrab(inode); xfs_syncd_queue_work(ip->i_mount, inode, xfs_flush_device_work); diff --git a/fs/xfs/quota/xfs_dquot.c b/fs/xfs/quota/xfs_dquot.c index fc9f3fb39b7..68adc5fd9b9 100644 --- a/fs/xfs/quota/xfs_dquot.c +++ b/fs/xfs/quota/xfs_dquot.c @@ -431,7 +431,7 @@ xfs_qm_dqalloc( * when it unlocks the inode. Since we want to keep the quota * inode around, we bump the vnode ref count now. */ - VN_HOLD(XFS_ITOV(quotip)); + VN_HOLD(VFS_I(quotip)); xfs_trans_ijoin(tp, quotip, XFS_ILOCK_EXCL); nmaps = 1; diff --git a/fs/xfs/xfs_bmap.c b/fs/xfs/xfs_bmap.c index 3c4beb3a432..2f46b67f932 100644 --- a/fs/xfs/xfs_bmap.c +++ b/fs/xfs/xfs_bmap.c @@ -4000,7 +4000,7 @@ xfs_bmap_add_attrfork( ip->i_d.di_aformat = XFS_DINODE_FMT_EXTENTS; } ASSERT(ip->i_d.di_anextents == 0); - VN_HOLD(XFS_ITOV(ip)); + VN_HOLD(VFS_I(ip)); xfs_trans_ijoin(tp, ip, XFS_ILOCK_EXCL); xfs_trans_log_inode(tp, ip, XFS_ILOG_CORE); switch (ip->i_d.di_format) { diff --git a/fs/xfs/xfs_dfrag.c b/fs/xfs/xfs_dfrag.c index 2211e885ef2..9e751011e23 100644 --- a/fs/xfs/xfs_dfrag.c +++ b/fs/xfs/xfs_dfrag.c @@ -150,8 +150,8 @@ xfs_swap_extents( } sbp = &sxp->sx_stat; - vp = XFS_ITOV(ip); - tvp = XFS_ITOV(tip); + vp = VFS_I(ip); + tvp = VFS_I(tip); /* Lock in i_ino order */ if (ip->i_ino < tip->i_ino) { diff --git a/fs/xfs/xfs_inode.c b/fs/xfs/xfs_inode.c index 46cecba0992..cfbafc937ee 100644 --- a/fs/xfs/xfs_inode.c +++ b/fs/xfs/xfs_inode.c @@ -1408,7 +1408,7 @@ xfs_itruncate_start( (flags == XFS_ITRUNC_MAYBE)); mp = ip->i_mount; - vp = XFS_ITOV(ip); + vp = VFS_I(ip); /* wait for the completion of any pending DIOs */ if (new_size < ip->i_size) diff --git a/fs/xfs/xfs_inode.h b/fs/xfs/xfs_inode.h index f04e026f6e0..4e1e55e9077 100644 --- a/fs/xfs/xfs_inode.h +++ b/fs/xfs/xfs_inode.h @@ -279,7 +279,6 @@ static inline struct inode *VFS_I(struct xfs_inode *ip) { return (struct inode *)ip->i_vnode; } -#define XFS_ITOV(ip) VFS_I(ip) /* * i_flags helper functions diff --git a/fs/xfs/xfs_itable.c b/fs/xfs/xfs_itable.c index 9a3ef9dcaeb..4feda541e71 100644 --- a/fs/xfs/xfs_itable.c +++ b/fs/xfs/xfs_itable.c @@ -72,7 +72,7 @@ xfs_bulkstat_one_iget( ASSERT(ip != NULL); ASSERT(ip->i_blkno != (xfs_daddr_t)0); - vp = XFS_ITOV(ip); + vp = VFS_I(ip); dic = &ip->i_d; /* xfs_iget returns the following without needing diff --git a/fs/xfs/xfs_utils.h b/fs/xfs/xfs_utils.h index f316cb85d8e..7b533dfea60 100644 --- a/fs/xfs/xfs_utils.h +++ b/fs/xfs/xfs_utils.h @@ -18,8 +18,8 @@ #ifndef __XFS_UTILS_H__ #define __XFS_UTILS_H__ -#define IRELE(ip) VN_RELE(XFS_ITOV(ip)) -#define IHOLD(ip) VN_HOLD(XFS_ITOV(ip)) +#define IRELE(ip) VN_RELE(VFS_I(ip)) +#define IHOLD(ip) VN_HOLD(VFS_I(ip)) extern int xfs_truncate_file(xfs_mount_t *, xfs_inode_t *); extern int xfs_dir_ialloc(xfs_trans_t **, xfs_inode_t *, mode_t, xfs_nlink_t, diff --git a/fs/xfs/xfs_vfsops.c b/fs/xfs/xfs_vfsops.c index 5f461ce4441..38450f1fa2a 100644 --- a/fs/xfs/xfs_vfsops.c +++ b/fs/xfs/xfs_vfsops.c @@ -128,7 +128,7 @@ xfs_unmount_flush( xfs_inode_t *rip = mp->m_rootip; xfs_inode_t *rbmip; xfs_inode_t *rsumip = NULL; - bhv_vnode_t *rvp = XFS_ITOV(rip); + bhv_vnode_t *rvp = VFS_I(rip); int error; xfs_ilock(rip, XFS_ILOCK_EXCL | XFS_ILOCK_PARENT); @@ -146,7 +146,7 @@ xfs_unmount_flush( if (error == EFSCORRUPTED) goto fscorrupt_out; - ASSERT(vn_count(XFS_ITOV(rbmip)) == 1); + ASSERT(vn_count(VFS_I(rbmip)) == 1); rsumip = mp->m_rsumip; xfs_ilock(rsumip, XFS_ILOCK_EXCL); @@ -157,7 +157,7 @@ xfs_unmount_flush( if (error == EFSCORRUPTED) goto fscorrupt_out; - ASSERT(vn_count(XFS_ITOV(rsumip)) == 1); + ASSERT(vn_count(VFS_I(rsumip)) == 1); } /* @@ -479,7 +479,7 @@ xfs_sync_inodes( IPOINTER_INSERT(ip, mp); xfs_ilock(ip, lock_flags); - ASSERT(vp == XFS_ITOV(ip)); + ASSERT(vp == VFS_I(ip)); ASSERT(ip->i_mount == mp); vnode_refed = B_TRUE; diff --git a/fs/xfs/xfs_vnodeops.c b/fs/xfs/xfs_vnodeops.c index a2e470ae259..35a053fd161 100644 --- a/fs/xfs/xfs_vnodeops.c +++ b/fs/xfs/xfs_vnodeops.c @@ -83,7 +83,7 @@ xfs_setattr( cred_t *credp) { xfs_mount_t *mp = ip->i_mount; - struct inode *inode = XFS_ITOV(ip); + struct inode *inode = VFS_I(ip); int mask = iattr->ia_valid; xfs_trans_t *tp; int code; @@ -714,7 +714,7 @@ xfs_fsync( return XFS_ERROR(EIO); /* capture size updates in I/O completion before writing the inode. */ - error = filemap_fdatawait(vn_to_inode(XFS_ITOV(ip))->i_mapping); + error = filemap_fdatawait(vn_to_inode(VFS_I(ip))->i_mapping); if (error) return XFS_ERROR(error); @@ -1160,7 +1160,7 @@ int xfs_release( xfs_inode_t *ip) { - bhv_vnode_t *vp = XFS_ITOV(ip); + bhv_vnode_t *vp = VFS_I(ip); xfs_mount_t *mp = ip->i_mount; int error; @@ -1227,7 +1227,7 @@ int xfs_inactive( xfs_inode_t *ip) { - bhv_vnode_t *vp = XFS_ITOV(ip); + bhv_vnode_t *vp = VFS_I(ip); xfs_bmap_free_t free_list; xfs_fsblock_t first_block; int committed; @@ -2873,7 +2873,7 @@ int xfs_reclaim( xfs_inode_t *ip) { - bhv_vnode_t *vp = XFS_ITOV(ip); + bhv_vnode_t *vp = VFS_I(ip); xfs_itrace_entry(ip); @@ -3341,7 +3341,7 @@ xfs_free_file_space( xfs_trans_t *tp; int need_iolock = 1; - vp = XFS_ITOV(ip); + vp = VFS_I(ip); mp = ip->i_mount; xfs_itrace_entry(ip); -- GitLab From e6064d30c3407db7f8c19d5538ec847b29e47e30 Mon Sep 17 00:00:00 2001 From: David Chinner Date: Wed, 13 Aug 2008 16:01:45 +1000 Subject: [PATCH 142/750] [XFS] XFS: Kill xfs_vtoi() xfs_vtoi() is redundant and only unsed in small sections of code. Replace them with widely used XFS_I() inline and kill xfs_vtoi(). SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31725a Signed-off-by: David Chinner Signed-off-by: Niv Sardi Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_aops.c | 3 +-- fs/xfs/linux-2.6/xfs_vnode.h | 4 ++-- fs/xfs/xfs_acl.c | 16 ++++++++-------- fs/xfs/xfs_inode.h | 5 ----- 4 files changed, 11 insertions(+), 17 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_aops.c b/fs/xfs/linux-2.6/xfs_aops.c index fa47e43b8b4..f42f80a3b1f 100644 --- a/fs/xfs/linux-2.6/xfs_aops.c +++ b/fs/xfs/linux-2.6/xfs_aops.c @@ -73,7 +73,6 @@ xfs_page_trace( unsigned long pgoff) { xfs_inode_t *ip; - bhv_vnode_t *vp = vn_from_inode(inode); loff_t isize = i_size_read(inode); loff_t offset = page_offset(page); int delalloc = -1, unmapped = -1, unwritten = -1; @@ -81,7 +80,7 @@ xfs_page_trace( if (page_has_buffers(page)) xfs_count_page_state(page, &delalloc, &unmapped, &unwritten); - ip = xfs_vtoi(vp); + ip = XFS_I(inode); if (!ip->i_rwtrace) return; diff --git a/fs/xfs/linux-2.6/xfs_vnode.h b/fs/xfs/linux-2.6/xfs_vnode.h index 41ca2cec5d3..c3afecf8c5b 100644 --- a/fs/xfs/linux-2.6/xfs_vnode.h +++ b/fs/xfs/linux-2.6/xfs_vnode.h @@ -89,9 +89,9 @@ extern bhv_vnode_t *vn_hold(bhv_vnode_t *); #if defined(XFS_INODE_TRACE) #define VN_HOLD(vp) \ ((void)vn_hold(vp), \ - xfs_itrace_hold(xfs_vtoi(vp), __FILE__, __LINE__, (inst_t *)__return_address)) + xfs_itrace_hold(XFS_I(vp), __FILE__, __LINE__, (inst_t *)__return_address)) #define VN_RELE(vp) \ - (xfs_itrace_rele(xfs_vtoi(vp), __FILE__, __LINE__, (inst_t *)__return_address), \ + (xfs_itrace_rele(XFS_I(vp), __FILE__, __LINE__, (inst_t *)__return_address), \ iput(vn_to_inode(vp))) #else #define VN_HOLD(vp) ((void)vn_hold(vp)) diff --git a/fs/xfs/xfs_acl.c b/fs/xfs/xfs_acl.c index 3e4648ad9cf..fdeca54540a 100644 --- a/fs/xfs/xfs_acl.c +++ b/fs/xfs/xfs_acl.c @@ -239,7 +239,7 @@ xfs_acl_vget( goto out; } if (kind == _ACL_TYPE_ACCESS) - xfs_acl_sync_mode(xfs_vtoi(vp)->i_d.di_mode, xfs_acl); + xfs_acl_sync_mode(XFS_I(vp)->i_d.di_mode, xfs_acl); error = -posix_acl_xfs_to_xattr(xfs_acl, ext_acl, size); } out: @@ -259,7 +259,7 @@ xfs_acl_vremove( VN_HOLD(vp); error = xfs_acl_allow_set(vp, kind); if (!error) { - error = xfs_attr_remove(xfs_vtoi(vp), + error = xfs_attr_remove(XFS_I(vp), kind == _ACL_TYPE_DEFAULT? SGI_ACL_DEFAULT: SGI_ACL_FILE, ATTR_ROOT); @@ -372,7 +372,7 @@ xfs_acl_allow_set( return ENOTDIR; if (vp->i_sb->s_flags & MS_RDONLY) return EROFS; - if (xfs_vtoi(vp)->i_d.di_uid != current->fsuid && !capable(CAP_FOWNER)) + if (XFS_I(vp)->i_d.di_uid != current->fsuid && !capable(CAP_FOWNER)) return EPERM; return 0; } @@ -576,7 +576,7 @@ xfs_acl_get_attr( ASSERT((flags & ATTR_KERNOVAL) ? (aclp == NULL) : 1); flags |= ATTR_ROOT; - *error = xfs_attr_get(xfs_vtoi(vp), + *error = xfs_attr_get(XFS_I(vp), kind == _ACL_TYPE_ACCESS ? SGI_ACL_FILE : SGI_ACL_DEFAULT, (char *)aclp, &len, flags); @@ -615,7 +615,7 @@ xfs_acl_set_attr( INT_SET(newace->ae_perm, ARCH_CONVERT, ace->ae_perm); } INT_SET(newacl->acl_cnt, ARCH_CONVERT, aclp->acl_cnt); - *error = xfs_attr_set(xfs_vtoi(vp), + *error = xfs_attr_set(XFS_I(vp), kind == _ACL_TYPE_ACCESS ? SGI_ACL_FILE: SGI_ACL_DEFAULT, (char *)newacl, len, ATTR_ROOT); @@ -639,7 +639,7 @@ xfs_acl_vtoacl( if (error) access_acl->acl_cnt = XFS_ACL_NOT_PRESENT; else /* We have a good ACL and the file mode, synchronize. */ - xfs_acl_sync_mode(xfs_vtoi(vp)->i_d.di_mode, access_acl); + xfs_acl_sync_mode(XFS_I(vp)->i_d.di_mode, access_acl); } if (default_acl) { @@ -734,7 +734,7 @@ xfs_acl_setmode( * mode. The m:: bits take precedence over the g:: bits. */ iattr.ia_valid = ATTR_MODE; - iattr.ia_mode = xfs_vtoi(vp)->i_d.di_mode; + iattr.ia_mode = XFS_I(vp)->i_d.di_mode; iattr.ia_mode &= ~(S_IRWXU|S_IRWXG|S_IRWXO); ap = acl->acl_entry; for (i = 0; i < acl->acl_cnt; ++i) { @@ -764,7 +764,7 @@ xfs_acl_setmode( if (gap && nomask) iattr.ia_mode |= gap->ae_perm << 3; - return xfs_setattr(xfs_vtoi(vp), &iattr, 0, sys_cred); + return xfs_setattr(XFS_I(vp), &iattr, 0, sys_cred); } /* diff --git a/fs/xfs/xfs_inode.h b/fs/xfs/xfs_inode.h index 4e1e55e9077..4088951230a 100644 --- a/fs/xfs/xfs_inode.h +++ b/fs/xfs/xfs_inode.h @@ -269,11 +269,6 @@ static inline struct xfs_inode *XFS_I(struct inode *inode) return (struct xfs_inode *)inode->i_private; } -static inline struct xfs_inode *xfs_vtoi(bhv_vnode_t *vp) -{ - return XFS_I((struct inode *)vp); -} - /* convert from xfs inode to vfs inode */ static inline struct inode *VFS_I(struct xfs_inode *ip) { -- GitLab From 6785073ba138a2f0dc575c332c1812b713670b6a Mon Sep 17 00:00:00 2001 From: David Chinner Date: Wed, 13 Aug 2008 16:02:51 +1000 Subject: [PATCH 143/750] [XFS] Use KM_NOFS for incore inode extent tree allocation V2 If we allow incore extent tree allocations to recurse into the filesystem under memory pressure, new delayed allocations through xfs_iomap_write_delay() can deadlock on themselves if memory reclaim tries to write back dirty pages from that inode. It will deadlock in xfs_iomap_write_allocate() trying to take the ilock we already hold. This can also show up as complex ABBA deadlocks when multiple threads are triggering memory reclaim when trying to allocate extents. The main cause of this is the fact that delayed allocation is not done in a transaction, so KM_NOFS is not automatically added to the allocations to prevent this recursion. Mark all allocations done for the incore inode extent tree as KM_NOFS to ensure they never recurse back into the filesystem. Version 2: o KM_NOFS implies KM_SLEEP, so just use KM_NOFS SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31726a Signed-off-by: David Chinner Signed-off-by: Niv Sardi Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/xfs_inode.c | 16 +++++++--------- 1 file changed, 7 insertions(+), 9 deletions(-) diff --git a/fs/xfs/xfs_inode.c b/fs/xfs/xfs_inode.c index cfbafc937ee..8da67d5717c 100644 --- a/fs/xfs/xfs_inode.c +++ b/fs/xfs/xfs_inode.c @@ -3707,7 +3707,7 @@ xfs_iext_add_indirect_multi( * (all extents past */ if (nex2) { byte_diff = nex2 * sizeof(xfs_bmbt_rec_t); - nex2_ep = (xfs_bmbt_rec_t *) kmem_alloc(byte_diff, KM_SLEEP); + nex2_ep = (xfs_bmbt_rec_t *) kmem_alloc(byte_diff, KM_NOFS); memmove(nex2_ep, &erp->er_extbuf[idx], byte_diff); erp->er_extcount -= nex2; xfs_iext_irec_update_extoffs(ifp, erp_idx + 1, -nex2); @@ -4007,8 +4007,7 @@ xfs_iext_realloc_direct( ifp->if_u1.if_extents = kmem_realloc(ifp->if_u1.if_extents, rnew_size, - ifp->if_real_bytes, - KM_SLEEP); + ifp->if_real_bytes, KM_NOFS); } if (rnew_size > ifp->if_real_bytes) { memset(&ifp->if_u1.if_extents[ifp->if_bytes / @@ -4067,7 +4066,7 @@ xfs_iext_inline_to_direct( xfs_ifork_t *ifp, /* inode fork pointer */ int new_size) /* number of extents in file */ { - ifp->if_u1.if_extents = kmem_alloc(new_size, KM_SLEEP); + ifp->if_u1.if_extents = kmem_alloc(new_size, KM_NOFS); memset(ifp->if_u1.if_extents, 0, new_size); if (ifp->if_bytes) { memcpy(ifp->if_u1.if_extents, ifp->if_u2.if_inline_ext, @@ -4099,7 +4098,7 @@ xfs_iext_realloc_indirect( } else { ifp->if_u1.if_ext_irec = (xfs_ext_irec_t *) kmem_realloc(ifp->if_u1.if_ext_irec, - new_size, size, KM_SLEEP); + new_size, size, KM_NOFS); } } @@ -4341,11 +4340,10 @@ xfs_iext_irec_init( nextents = ifp->if_bytes / (uint)sizeof(xfs_bmbt_rec_t); ASSERT(nextents <= XFS_LINEAR_EXTS); - erp = (xfs_ext_irec_t *) - kmem_alloc(sizeof(xfs_ext_irec_t), KM_SLEEP); + erp = kmem_alloc(sizeof(xfs_ext_irec_t), KM_NOFS); if (nextents == 0) { - ifp->if_u1.if_extents = kmem_alloc(XFS_IEXT_BUFSZ, KM_SLEEP); + ifp->if_u1.if_extents = kmem_alloc(XFS_IEXT_BUFSZ, KM_NOFS); } else if (!ifp->if_real_bytes) { xfs_iext_inline_to_direct(ifp, XFS_IEXT_BUFSZ); } else if (ifp->if_real_bytes < XFS_IEXT_BUFSZ) { @@ -4393,7 +4391,7 @@ xfs_iext_irec_new( /* Initialize new extent record */ erp = ifp->if_u1.if_ext_irec; - erp[erp_idx].er_extbuf = kmem_alloc(XFS_IEXT_BUFSZ, KM_SLEEP); + erp[erp_idx].er_extbuf = kmem_alloc(XFS_IEXT_BUFSZ, KM_NOFS); ifp->if_real_bytes = nlists * XFS_IEXT_BUFSZ; memset(erp[erp_idx].er_extbuf, 0, XFS_IEXT_BUFSZ); erp[erp_idx].er_extcount = 0; -- GitLab From 5e9da7b7a1edfc75a839b0269935393fa347f38b Mon Sep 17 00:00:00 2001 From: Niv Sardi Date: Wed, 13 Aug 2008 16:03:35 +1000 Subject: [PATCH 144/750] [XFS] Move attr log alloc size calculator to another function. We will need that to be able to calculate the size of log we need for a specific attr (for Create+EA). The local flag is needed so that we can fail if we run into ENOSPC when trying to alloc blocks. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31727a Signed-off-by: Niv Sardi Signed-off-by: Christoph Hellwig Signed-off-by: Tim Shimmin Signed-off-by: Lachlan McIlroy --- fs/xfs/xfs_attr.c | 80 ++++++++++++++++++++++++++++------------------- fs/xfs/xfs_attr.h | 1 + 2 files changed, 49 insertions(+), 32 deletions(-) diff --git a/fs/xfs/xfs_attr.c b/fs/xfs/xfs_attr.c index 78de80e3caa..ffa634d1c18 100644 --- a/fs/xfs/xfs_attr.c +++ b/fs/xfs/xfs_attr.c @@ -194,6 +194,46 @@ xfs_attr_get( return(error); } +/* + * Calculate how many blocks we need for the new attribute, + */ +int +xfs_attr_calc_size( + struct xfs_inode *ip, + int namelen, + int valuelen, + int *local) +{ + struct xfs_mount *mp = ip->i_mount; + int size; + int nblks; + + /* + * Determine space new attribute will use, and if it would be + * "local" or "remote" (note: local != inline). + */ + size = xfs_attr_leaf_newentsize(namelen, valuelen, + mp->m_sb.sb_blocksize, local); + + nblks = XFS_DAENTER_SPACE_RES(mp, XFS_ATTR_FORK); + if (*local) { + if (size > (mp->m_sb.sb_blocksize >> 1)) { + /* Double split possible */ + nblks *= 2; + } + } else { + /* + * Out of line attribute, cannot double split, but + * make room for the attribute value itself. + */ + uint dblocks = XFS_B_TO_FSB(mp, valuelen); + nblks += dblocks; + nblks += XFS_NEXTENTADD_SPACE_RES(mp, dblocks, XFS_ATTR_FORK); + } + + return nblks; +} + STATIC int xfs_attr_set_int(xfs_inode_t *dp, struct xfs_name *name, char *value, int valuelen, int flags) @@ -202,10 +242,9 @@ xfs_attr_set_int(xfs_inode_t *dp, struct xfs_name *name, xfs_fsblock_t firstblock; xfs_bmap_free_t flist; int error, err2, committed; - int local, size; - uint nblks; xfs_mount_t *mp = dp->i_mount; int rsvd = (flags & ATTR_ROOT) != 0; + int local; /* * Attach the dquots to the inode. @@ -241,30 +280,8 @@ xfs_attr_set_int(xfs_inode_t *dp, struct xfs_name *name, args.whichfork = XFS_ATTR_FORK; args.op_flags = XFS_DA_OP_ADDNAME | XFS_DA_OP_OKNOENT; - /* - * Determine space new attribute will use, and if it would be - * "local" or "remote" (note: local != inline). - */ - size = xfs_attr_leaf_newentsize(name->len, valuelen, - mp->m_sb.sb_blocksize, &local); - - nblks = XFS_DAENTER_SPACE_RES(mp, XFS_ATTR_FORK); - if (local) { - if (size > (mp->m_sb.sb_blocksize >> 1)) { - /* Double split possible */ - nblks <<= 1; - } - } else { - uint dblocks = XFS_B_TO_FSB(mp, valuelen); - /* Out of line attribute, cannot double split, but make - * room for the attribute value itself. - */ - nblks += dblocks; - nblks += XFS_NEXTENTADD_SPACE_RES(mp, dblocks, XFS_ATTR_FORK); - } - /* Size is now blocks for attribute data */ - args.total = nblks; + args.total = xfs_attr_calc_size(dp, name->len, valuelen, &local); /* * Start our first transaction of the day. @@ -286,18 +303,17 @@ xfs_attr_set_int(xfs_inode_t *dp, struct xfs_name *name, if (rsvd) args.trans->t_flags |= XFS_TRANS_RESERVE; - if ((error = xfs_trans_reserve(args.trans, (uint) nblks, - XFS_ATTRSET_LOG_RES(mp, nblks), - 0, XFS_TRANS_PERM_LOG_RES, - XFS_ATTRSET_LOG_COUNT))) { + if ((error = xfs_trans_reserve(args.trans, args.total, + XFS_ATTRSET_LOG_RES(mp, args.total), 0, + XFS_TRANS_PERM_LOG_RES, XFS_ATTRSET_LOG_COUNT))) { xfs_trans_cancel(args.trans, 0); return(error); } xfs_ilock(dp, XFS_ILOCK_EXCL); - error = XFS_TRANS_RESERVE_QUOTA_NBLKS(mp, args.trans, dp, nblks, 0, - rsvd ? XFS_QMOPT_RES_REGBLKS | XFS_QMOPT_FORCE_RES : - XFS_QMOPT_RES_REGBLKS); + error = XFS_TRANS_RESERVE_QUOTA_NBLKS(mp, args.trans, dp, args.total, 0, + rsvd ? XFS_QMOPT_RES_REGBLKS | XFS_QMOPT_FORCE_RES : + XFS_QMOPT_RES_REGBLKS); if (error) { xfs_iunlock(dp, XFS_ILOCK_EXCL); xfs_trans_cancel(args.trans, XFS_TRANS_RELEASE_LOG_RES); diff --git a/fs/xfs/xfs_attr.h b/fs/xfs/xfs_attr.h index 8b2d31c19e4..fb3b2a68b9b 100644 --- a/fs/xfs/xfs_attr.h +++ b/fs/xfs/xfs_attr.h @@ -129,6 +129,7 @@ typedef struct xfs_attr_list_context { /* * Overall external interface routines. */ +int xfs_attr_calc_size(struct xfs_inode *, int, int, int *); int xfs_attr_inactive(struct xfs_inode *dp); int xfs_attr_fetch(struct xfs_inode *, struct xfs_name *, char *, int *, int); int xfs_attr_rmtval_get(struct xfs_da_args *args); -- GitLab From a738159df2b97398f960978272944cbdd8f726ef Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:04:05 +1000 Subject: [PATCH 145/750] [XFS] don't leak m_fsname/m_rtname/m_logname Add a helper to free the m_fsname/m_rtname/m_logname allocations and use it properly for all mount failure cases. Also switch the allocations for these to kstrdup while we're at it. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31728a Signed-off-by: Christoph Hellwig Signed-off-by: Niv Sardi Signed-off-by: David Chinner Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_super.c | 51 +++++++++++++++++++++++++++++------- fs/xfs/xfs_mount.c | 7 ----- 2 files changed, 41 insertions(+), 17 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_super.c b/fs/xfs/linux-2.6/xfs_super.c index c9ec44a02e2..27758409fc8 100644 --- a/fs/xfs/linux-2.6/xfs_super.c +++ b/fs/xfs/linux-2.6/xfs_super.c @@ -1200,6 +1200,15 @@ xfssyncd( return 0; } +STATIC void +xfs_free_fsname( + struct xfs_mount *mp) +{ + kfree(mp->m_fsname); + kfree(mp->m_rtname); + kfree(mp->m_logname); +} + STATIC void xfs_fs_put_super( struct super_block *sb) @@ -1261,6 +1270,7 @@ xfs_fs_put_super( xfs_close_devices(mp); xfs_qmops_put(mp); xfs_dmops_put(mp); + xfs_free_fsname(mp); kfree(mp); } @@ -1517,6 +1527,8 @@ xfs_start_flags( struct xfs_mount_args *ap, struct xfs_mount *mp) { + int error; + /* Values are in BBs */ if ((ap->flags & XFSMNT_NOALIGN) != XFSMNT_NOALIGN) { /* @@ -1549,17 +1561,27 @@ xfs_start_flags( ap->logbufsize); return XFS_ERROR(EINVAL); } + + error = ENOMEM; + mp->m_logbsize = ap->logbufsize; mp->m_fsname_len = strlen(ap->fsname) + 1; - mp->m_fsname = kmem_alloc(mp->m_fsname_len, KM_SLEEP); - strcpy(mp->m_fsname, ap->fsname); + + mp->m_fsname = kstrdup(ap->fsname, GFP_KERNEL); + if (!mp->m_fsname) + goto out; + if (ap->rtname[0]) { - mp->m_rtname = kmem_alloc(strlen(ap->rtname) + 1, KM_SLEEP); - strcpy(mp->m_rtname, ap->rtname); + mp->m_rtname = kstrdup(ap->rtname, GFP_KERNEL); + if (!mp->m_rtname) + goto out_free_fsname; + } + if (ap->logname[0]) { - mp->m_logname = kmem_alloc(strlen(ap->logname) + 1, KM_SLEEP); - strcpy(mp->m_logname, ap->logname); + mp->m_logname = kstrdup(ap->logname, GFP_KERNEL); + if (!mp->m_logname) + goto out_free_rtname; } if (ap->flags & XFSMNT_WSYNC) @@ -1632,6 +1654,14 @@ xfs_start_flags( if (ap->flags & XFSMNT_DMAPI) mp->m_flags |= XFS_MOUNT_DMAPI; return 0; + + + out_free_rtname: + kfree(mp->m_rtname); + out_free_fsname: + kfree(mp->m_fsname); + out: + return error; } /* @@ -1792,10 +1822,10 @@ xfs_fs_fill_super( */ error = xfs_start_flags(args, mp); if (error) - goto out_destroy_counters; + goto out_free_fsname; error = xfs_readsb(mp, flags); if (error) - goto out_destroy_counters; + goto out_free_fsname; error = xfs_finish_flags(args, mp); if (error) goto out_free_sb; @@ -1857,7 +1887,8 @@ xfs_fs_fill_super( xfs_filestream_unmount(mp); out_free_sb: xfs_freesb(mp); - out_destroy_counters: + out_free_fsname: + xfs_free_fsname(mp); xfs_icsb_destroy_counters(mp); xfs_close_devices(mp); out_put_qmops: @@ -1893,7 +1924,7 @@ xfs_fs_fill_super( IRELE(mp->m_rootip); xfs_unmountfs(mp); - goto out_destroy_counters; + goto out_free_fsname; } STATIC int diff --git a/fs/xfs/xfs_mount.c b/fs/xfs/xfs_mount.c index 6c5d1325e7f..31699b19bb3 100644 --- a/fs/xfs/xfs_mount.c +++ b/fs/xfs/xfs_mount.c @@ -146,13 +146,6 @@ xfs_mount_free( mutex_destroy(&mp->m_growlock); if (mp->m_quotainfo) XFS_QM_DONE(mp); - - if (mp->m_fsname != NULL) - kmem_free(mp->m_fsname); - if (mp->m_rtname != NULL) - kmem_free(mp->m_rtname); - if (mp->m_logname != NULL) - kmem_free(mp->m_logname); } /* -- GitLab From 322ff6b8cd54feb1c4c0426630f3642ab1dd2176 Mon Sep 17 00:00:00 2001 From: Niv Sardi Date: Wed, 13 Aug 2008 16:05:49 +1000 Subject: [PATCH 146/750] [XFS] Move xfs_attr_rolltrans to xfs_trans_roll Move it from the attr code to the transaction code and make the attr code call the new function. We rolltrans is really usefull whenever we want to use rolling transaction, should be generic, it isn't dependent on any part of the attr code anyway. We use this excuse to change all the: if ((error = xfs_attr_rolltrans())) calls into: error = xfs_trans_roll(); if (error) SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31729a Signed-off-by: Niv Sardi Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/xfs_attr.c | 30 +++++++++++------ fs/xfs/xfs_attr_leaf.c | 75 +++++------------------------------------- fs/xfs/xfs_attr_leaf.h | 2 -- fs/xfs/xfs_trans.c | 63 +++++++++++++++++++++++++++++++++++ fs/xfs/xfs_trans.h | 1 + 5 files changed, 92 insertions(+), 79 deletions(-) diff --git a/fs/xfs/xfs_attr.c b/fs/xfs/xfs_attr.c index ffa634d1c18..f7cdc28aff4 100644 --- a/fs/xfs/xfs_attr.c +++ b/fs/xfs/xfs_attr.c @@ -400,7 +400,9 @@ xfs_attr_set_int(xfs_inode_t *dp, struct xfs_name *name, * Commit the leaf transformation. We'll need another (linked) * transaction to add the new attribute to the leaf. */ - if ((error = xfs_attr_rolltrans(&args.trans, dp))) + + error = xfs_trans_roll(&args.trans, dp); + if (error) goto out; } @@ -980,7 +982,8 @@ xfs_attr_leaf_addname(xfs_da_args_t *args) * Commit the current trans (including the inode) and start * a new one. */ - if ((error = xfs_attr_rolltrans(&args->trans, dp))) + error = xfs_trans_roll(&args->trans, dp); + if (error) return (error); /* @@ -994,7 +997,8 @@ xfs_attr_leaf_addname(xfs_da_args_t *args) * Commit the transaction that added the attr name so that * later routines can manage their own transactions. */ - if ((error = xfs_attr_rolltrans(&args->trans, dp))) + error = xfs_trans_roll(&args->trans, dp); + if (error) return (error); /* @@ -1083,7 +1087,7 @@ xfs_attr_leaf_addname(xfs_da_args_t *args) /* * Commit the remove and start the next trans in series. */ - error = xfs_attr_rolltrans(&args->trans, dp); + error = xfs_trans_roll(&args->trans, dp); } else if (args->rmtblkno > 0) { /* @@ -1314,7 +1318,8 @@ restart: * Commit the node conversion and start the next * trans in the chain. */ - if ((error = xfs_attr_rolltrans(&args->trans, dp))) + error = xfs_trans_roll(&args->trans, dp); + if (error) goto out; goto restart; @@ -1365,7 +1370,8 @@ restart: * Commit the leaf addition or btree split and start the next * trans in the chain. */ - if ((error = xfs_attr_rolltrans(&args->trans, dp))) + error = xfs_trans_roll(&args->trans, dp); + if (error) goto out; /* @@ -1465,7 +1471,8 @@ restart: /* * Commit and start the next trans in the chain. */ - if ((error = xfs_attr_rolltrans(&args->trans, dp))) + error = xfs_trans_roll(&args->trans, dp); + if (error) goto out; } else if (args->rmtblkno > 0) { @@ -1597,7 +1604,8 @@ xfs_attr_node_removename(xfs_da_args_t *args) /* * Commit the Btree join operation and start a new trans. */ - if ((error = xfs_attr_rolltrans(&args->trans, dp))) + error = xfs_trans_roll(&args->trans, dp); + if (error) goto out; } @@ -2098,7 +2106,8 @@ xfs_attr_rmtval_set(xfs_da_args_t *args) /* * Start the next trans in the chain. */ - if ((error = xfs_attr_rolltrans(&args->trans, dp))) + error = xfs_trans_roll(&args->trans, dp); + if (error) return (error); } @@ -2248,7 +2257,8 @@ xfs_attr_rmtval_remove(xfs_da_args_t *args) /* * Close out trans and start the next one in the chain. */ - if ((error = xfs_attr_rolltrans(&args->trans, args->dp))) + error = xfs_trans_roll(&args->trans, args->dp); + if (error) return (error); } return(0); diff --git a/fs/xfs/xfs_attr_leaf.c b/fs/xfs/xfs_attr_leaf.c index 23ef5d7c87e..79da6b2ea99 100644 --- a/fs/xfs/xfs_attr_leaf.c +++ b/fs/xfs/xfs_attr_leaf.c @@ -2498,9 +2498,7 @@ xfs_attr_leaf_clearflag(xfs_da_args_t *args) /* * Commit the flag value change and start the next trans in series. */ - error = xfs_attr_rolltrans(&args->trans, args->dp); - - return(error); + return xfs_trans_roll(&args->trans, args->dp); } /* @@ -2547,9 +2545,7 @@ xfs_attr_leaf_setflag(xfs_da_args_t *args) /* * Commit the flag value change and start the next trans in series. */ - error = xfs_attr_rolltrans(&args->trans, args->dp); - - return(error); + return xfs_trans_roll(&args->trans, args->dp); } /* @@ -2665,7 +2661,7 @@ xfs_attr_leaf_flipflags(xfs_da_args_t *args) /* * Commit the flag value change and start the next trans in series. */ - error = xfs_attr_rolltrans(&args->trans, args->dp); + error = xfs_trans_roll(&args->trans, args->dp); return(error); } @@ -2723,7 +2719,7 @@ xfs_attr_root_inactive(xfs_trans_t **trans, xfs_inode_t *dp) /* * Commit the invalidate and start the next transaction. */ - error = xfs_attr_rolltrans(trans, dp); + error = xfs_trans_roll(trans, dp); return (error); } @@ -2825,7 +2821,8 @@ xfs_attr_node_inactive(xfs_trans_t **trans, xfs_inode_t *dp, xfs_dabuf_t *bp, /* * Atomically commit the whole invalidate stuff. */ - if ((error = xfs_attr_rolltrans(trans, dp))) + error = xfs_trans_roll(trans, dp); + if (error) return (error); } @@ -2964,7 +2961,8 @@ xfs_attr_leaf_freextent(xfs_trans_t **trans, xfs_inode_t *dp, /* * Roll to next transaction. */ - if ((error = xfs_attr_rolltrans(trans, dp))) + error = xfs_trans_roll(trans, dp); + if (error) return (error); } @@ -2974,60 +2972,3 @@ xfs_attr_leaf_freextent(xfs_trans_t **trans, xfs_inode_t *dp, return(0); } - - -/* - * Roll from one trans in the sequence of PERMANENT transactions to the next. - */ -int -xfs_attr_rolltrans(xfs_trans_t **transp, xfs_inode_t *dp) -{ - xfs_trans_t *trans; - unsigned int logres, count; - int error; - - /* - * Ensure that the inode is always logged. - */ - trans = *transp; - xfs_trans_log_inode(trans, dp, XFS_ILOG_CORE); - - /* - * Copy the critical parameters from one trans to the next. - */ - logres = trans->t_log_res; - count = trans->t_log_count; - *transp = xfs_trans_dup(trans); - - /* - * Commit the current transaction. - * If this commit failed, then it'd just unlock those items that - * are not marked ihold. That also means that a filesystem shutdown - * is in progress. The caller takes the responsibility to cancel - * the duplicate transaction that gets returned. - */ - if ((error = xfs_trans_commit(trans, 0))) - return (error); - - trans = *transp; - - /* - * Reserve space in the log for th next transaction. - * This also pushes items in the "AIL", the list of logged items, - * out to disk if they are taking up space at the tail of the log - * that we want to use. This requires that either nothing be locked - * across this call, or that anything that is locked be logged in - * the prior and the next transactions. - */ - error = xfs_trans_reserve(trans, 0, logres, 0, - XFS_TRANS_PERM_LOG_RES, count); - /* - * Ensure that the inode is in the new transaction and locked. - */ - if (!error) { - xfs_trans_ijoin(trans, dp, XFS_ILOCK_EXCL); - xfs_trans_ihold(trans, dp); - } - return (error); - -} diff --git a/fs/xfs/xfs_attr_leaf.h b/fs/xfs/xfs_attr_leaf.h index 5ecf437b782..83e9af417ca 100644 --- a/fs/xfs/xfs_attr_leaf.h +++ b/fs/xfs/xfs_attr_leaf.h @@ -274,6 +274,4 @@ int xfs_attr_leaf_order(struct xfs_dabuf *leaf1_bp, struct xfs_dabuf *leaf2_bp); int xfs_attr_leaf_newentsize(int namelen, int valuelen, int blocksize, int *local); -int xfs_attr_rolltrans(struct xfs_trans **transp, struct xfs_inode *dp); - #endif /* __XFS_ATTR_LEAF_H__ */ diff --git a/fs/xfs/xfs_trans.c b/fs/xfs/xfs_trans.c index e4ebddd3c50..d98758a0967 100644 --- a/fs/xfs/xfs_trans.c +++ b/fs/xfs/xfs_trans.c @@ -43,6 +43,7 @@ #include "xfs_quota.h" #include "xfs_trans_priv.h" #include "xfs_trans_space.h" +#include "xfs_inode_item.h" STATIC void xfs_trans_apply_sb_deltas(xfs_trans_t *); @@ -1216,6 +1217,68 @@ xfs_trans_free( kmem_zone_free(xfs_trans_zone, tp); } +/* + * Roll from one trans in the sequence of PERMANENT transactions to + * the next: permanent transactions are only flushed out when + * committed with XFS_TRANS_RELEASE_LOG_RES, but we still want as soon + * as possible to let chunks of it go to the log. So we commit the + * chunk we've been working on and get a new transaction to continue. + */ +int +xfs_trans_roll( + struct xfs_trans **tpp, + struct xfs_inode *dp) +{ + struct xfs_trans *trans; + unsigned int logres, count; + int error; + + /* + * Ensure that the inode is always logged. + */ + trans = *tpp; + xfs_trans_log_inode(trans, dp, XFS_ILOG_CORE); + + /* + * Copy the critical parameters from one trans to the next. + */ + logres = trans->t_log_res; + count = trans->t_log_count; + *tpp = xfs_trans_dup(trans); + + /* + * Commit the current transaction. + * If this commit failed, then it'd just unlock those items that + * are not marked ihold. That also means that a filesystem shutdown + * is in progress. The caller takes the responsibility to cancel + * the duplicate transaction that gets returned. + */ + error = xfs_trans_commit(trans, 0); + if (error) + return (error); + + trans = *tpp; + + /* + * Reserve space in the log for th next transaction. + * This also pushes items in the "AIL", the list of logged items, + * out to disk if they are taking up space at the tail of the log + * that we want to use. This requires that either nothing be locked + * across this call, or that anything that is locked be logged in + * the prior and the next transactions. + */ + error = xfs_trans_reserve(trans, 0, logres, 0, + XFS_TRANS_PERM_LOG_RES, count); + /* + * Ensure that the inode is in the new transaction and locked. + */ + if (error) + return error; + + xfs_trans_ijoin(trans, dp, XFS_ILOCK_EXCL); + xfs_trans_ihold(trans, dp); + return 0; +} /* * THIS SHOULD BE REWRITTEN TO USE xfs_trans_next_item(). diff --git a/fs/xfs/xfs_trans.h b/fs/xfs/xfs_trans.h index 0804207c739..9161e998f1a 100644 --- a/fs/xfs/xfs_trans.h +++ b/fs/xfs/xfs_trans.h @@ -986,6 +986,7 @@ int _xfs_trans_commit(xfs_trans_t *, int *); #define xfs_trans_commit(tp, flags) _xfs_trans_commit(tp, flags, NULL) void xfs_trans_cancel(xfs_trans_t *, int); +int xfs_trans_roll(struct xfs_trans **, struct xfs_inode *); int xfs_trans_ail_init(struct xfs_mount *); void xfs_trans_ail_destroy(struct xfs_mount *); void xfs_trans_push_ail(struct xfs_mount *, xfs_lsn_t); -- GitLab From cdeb380aa2ca3b8f8ba3736f2469f5818eadb9aa Mon Sep 17 00:00:00 2001 From: Eric Sandeen Date: Wed, 13 Aug 2008 16:07:53 +1000 Subject: [PATCH 147/750] [XFS] remove INT_GET and friends Thanks to hch's endian work, INT_GET etc are no longer used, and may as well be removed. INT_SET is still used in the acl code, though. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31756a Signed-off-by: Eric Sandeen Signed-off-by: Niv Sardi Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/xfs_arch.h | 68 ----------------------------------------------- 1 file changed, 68 deletions(-) diff --git a/fs/xfs/xfs_arch.h b/fs/xfs/xfs_arch.h index f9472a2076d..0b3b5efe848 100644 --- a/fs/xfs/xfs_arch.h +++ b/fs/xfs/xfs_arch.h @@ -92,16 +92,6 @@ ((__u8*)(pointer))[1] = (((value) ) & 0xff); \ } -/* define generic INT_ macros */ - -#define INT_GET(reference,arch) \ - (((arch) == ARCH_NOCONVERT) \ - ? \ - (reference) \ - : \ - INT_SWAP((reference),(reference)) \ - ) - /* does not return a value */ #define INT_SET(reference,arch,valueref) \ (__builtin_constant_p(valueref) ? \ @@ -112,64 +102,6 @@ ) \ ) -/* does not return a value */ -#define INT_MOD_EXPR(reference,arch,code) \ - (((arch) == ARCH_NOCONVERT) \ - ? \ - (void)((reference) code) \ - : \ - (void)( \ - (reference) = INT_GET((reference),arch) , \ - ((reference) code), \ - INT_SET(reference, arch, reference) \ - ) \ - ) - -/* does not return a value */ -#define INT_MOD(reference,arch,delta) \ - (void)( \ - INT_MOD_EXPR(reference,arch,+=(delta)) \ - ) - -/* - * INT_COPY - copy a value between two locations with the - * _same architecture_ but _potentially different sizes_ - * - * if the types of the two parameters are equal or they are - * in native architecture, a simple copy is done - * - * otherwise, architecture conversions are done - * - */ - -/* does not return a value */ -#define INT_COPY(dst,src,arch) \ - ( \ - ((sizeof(dst) == sizeof(src)) || ((arch) == ARCH_NOCONVERT)) \ - ? \ - (void)((dst) = (src)) \ - : \ - INT_SET(dst, arch, INT_GET(src, arch)) \ - ) - -/* - * INT_XLATE - copy a value in either direction between two locations - * with different architectures - * - * dir < 0 - copy from memory to buffer (native to arch) - * dir > 0 - copy from buffer to memory (arch to native) - */ - -/* does not return a value */ -#define INT_XLATE(buf,mem,dir,arch) {\ - ASSERT(dir); \ - if (dir>0) { \ - (mem)=INT_GET(buf, arch); \ - } else { \ - INT_SET(buf, arch, mem); \ - } \ -} - /* * In directories inode numbers are stored as unaligned arrays of unsigned * 8bit integers on disk. -- GitLab From db7a2c71d287686eef1d4df1565fa32f89a9fe68 Mon Sep 17 00:00:00 2001 From: Eric Sandeen Date: Wed, 13 Aug 2008 16:09:25 +1000 Subject: [PATCH 148/750] [XFS] convert xfs to use ERR_CAST Looks like somehow xfs got missed in the conversion that took place in e231c2ee64eb1c5cd3c63c31da9dac7d888dcf7f, "Convert ERR_PTR(PTR_ERR(p)) instances to ERR_CAST(p) " SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31757a Signed-off-by: Eric Sandeen Acked-by: David Howells Signed-off-by: Niv Sardi Signed-off-by: Christoph Hellwig Signed-off-by: David Howells Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_export.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_export.c b/fs/xfs/linux-2.6/xfs_export.c index d3880b7c147..24fd598af84 100644 --- a/fs/xfs/linux-2.6/xfs_export.c +++ b/fs/xfs/linux-2.6/xfs_export.c @@ -167,7 +167,7 @@ xfs_fs_fh_to_dentry(struct super_block *sb, struct fid *fid, if (!inode) return NULL; if (IS_ERR(inode)) - return ERR_PTR(PTR_ERR(inode)); + return ERR_CAST(inode); result = d_alloc_anon(inode); if (!result) { iput(inode); @@ -198,7 +198,7 @@ xfs_fs_fh_to_parent(struct super_block *sb, struct fid *fid, if (!inode) return NULL; if (IS_ERR(inode)) - return ERR_PTR(PTR_ERR(inode)); + return ERR_CAST(inode); result = d_alloc_anon(inode); if (!result) { iput(inode); -- GitLab From 39dab9d7daf5f664a3569378107a2cb284c8a594 Mon Sep 17 00:00:00 2001 From: Eric Sandeen Date: Wed, 13 Aug 2008 16:10:52 +1000 Subject: [PATCH 149/750] [XFS] remove shouting-indirection macros from xfs_trans.h SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31758a Signed-off-by: Eric Sandeen Signed-off-by: Niv Sardi Signed-off-by: Lachlan McIlroy --- fs/xfs/xfs_bmap.c | 6 ++-- fs/xfs/xfs_trans.c | 12 ++++---- fs/xfs/xfs_trans.h | 11 ------- fs/xfs/xfs_trans_buf.c | 12 ++++---- fs/xfs/xfs_trans_item.c | 66 ++++++++++++++++++++--------------------- 5 files changed, 48 insertions(+), 59 deletions(-) diff --git a/fs/xfs/xfs_bmap.c b/fs/xfs/xfs_bmap.c index 2f46b67f932..bac82af39a5 100644 --- a/fs/xfs/xfs_bmap.c +++ b/fs/xfs/xfs_bmap.c @@ -6096,7 +6096,7 @@ xfs_bmap_get_bp( tp = cur->bc_tp; licp = &tp->t_items; while (!bp && licp != NULL) { - if (XFS_LIC_ARE_ALL_FREE(licp)) { + if (xfs_lic_are_all_free(licp)) { licp = licp->lic_next; continue; } @@ -6106,11 +6106,11 @@ xfs_bmap_get_bp( xfs_buf_log_item_t *bip; xfs_buf_t *lbp; - if (XFS_LIC_ISFREE(licp, i)) { + if (xfs_lic_isfree(licp, i)) { continue; } - lidp = XFS_LIC_SLOT(licp, i); + lidp = xfs_lic_slot(licp, i); lip = lidp->lid_item; if (lip->li_type != XFS_LI_BUF) continue; diff --git a/fs/xfs/xfs_trans.c b/fs/xfs/xfs_trans.c index d98758a0967..4e1c22a23be 100644 --- a/fs/xfs/xfs_trans.c +++ b/fs/xfs/xfs_trans.c @@ -254,7 +254,7 @@ _xfs_trans_alloc( tp->t_mountp = mp; tp->t_items_free = XFS_LIC_NUM_SLOTS; tp->t_busy_free = XFS_LBC_NUM_SLOTS; - XFS_LIC_INIT(&(tp->t_items)); + xfs_lic_init(&(tp->t_items)); XFS_LBC_INIT(&(tp->t_busy)); return tp; } @@ -283,7 +283,7 @@ xfs_trans_dup( ntp->t_mountp = tp->t_mountp; ntp->t_items_free = XFS_LIC_NUM_SLOTS; ntp->t_busy_free = XFS_LBC_NUM_SLOTS; - XFS_LIC_INIT(&(ntp->t_items)); + xfs_lic_init(&(ntp->t_items)); XFS_LBC_INIT(&(ntp->t_busy)); ASSERT(tp->t_flags & XFS_TRANS_PERM_LOG_RES); @@ -1170,7 +1170,7 @@ xfs_trans_cancel( while (licp != NULL) { lidp = licp->lic_descs; for (i = 0; i < licp->lic_unused; i++, lidp++) { - if (XFS_LIC_ISFREE(licp, i)) { + if (xfs_lic_isfree(licp, i)) { continue; } @@ -1316,7 +1316,7 @@ xfs_trans_committed( * Special case the chunk embedded in the transaction. */ licp = &(tp->t_items); - if (!(XFS_LIC_ARE_ALL_FREE(licp))) { + if (!(xfs_lic_are_all_free(licp))) { xfs_trans_chunk_committed(licp, tp->t_lsn, abortflag); } @@ -1325,7 +1325,7 @@ xfs_trans_committed( */ licp = licp->lic_next; while (licp != NULL) { - ASSERT(!XFS_LIC_ARE_ALL_FREE(licp)); + ASSERT(!xfs_lic_are_all_free(licp)); xfs_trans_chunk_committed(licp, tp->t_lsn, abortflag); next_licp = licp->lic_next; kmem_free(licp); @@ -1388,7 +1388,7 @@ xfs_trans_chunk_committed( lidp = licp->lic_descs; for (i = 0; i < licp->lic_unused; i++, lidp++) { - if (XFS_LIC_ISFREE(licp, i)) { + if (xfs_lic_isfree(licp, i)) { continue; } diff --git a/fs/xfs/xfs_trans.h b/fs/xfs/xfs_trans.h index 9161e998f1a..74c80bd2b0e 100644 --- a/fs/xfs/xfs_trans.h +++ b/fs/xfs/xfs_trans.h @@ -210,62 +210,52 @@ typedef struct xfs_log_item_chunk { * lic_unused to the right value (0 matches all free). The * lic_descs.lid_index values are set up as each desc is allocated. */ -#define XFS_LIC_INIT(cp) xfs_lic_init(cp) static inline void xfs_lic_init(xfs_log_item_chunk_t *cp) { cp->lic_free = XFS_LIC_FREEMASK; } -#define XFS_LIC_INIT_SLOT(cp,slot) xfs_lic_init_slot(cp, slot) static inline void xfs_lic_init_slot(xfs_log_item_chunk_t *cp, int slot) { cp->lic_descs[slot].lid_index = (unsigned char)(slot); } -#define XFS_LIC_VACANCY(cp) xfs_lic_vacancy(cp) static inline int xfs_lic_vacancy(xfs_log_item_chunk_t *cp) { return cp->lic_free & XFS_LIC_FREEMASK; } -#define XFS_LIC_ALL_FREE(cp) xfs_lic_all_free(cp) static inline void xfs_lic_all_free(xfs_log_item_chunk_t *cp) { cp->lic_free = XFS_LIC_FREEMASK; } -#define XFS_LIC_ARE_ALL_FREE(cp) xfs_lic_are_all_free(cp) static inline int xfs_lic_are_all_free(xfs_log_item_chunk_t *cp) { return ((cp->lic_free & XFS_LIC_FREEMASK) == XFS_LIC_FREEMASK); } -#define XFS_LIC_ISFREE(cp,slot) xfs_lic_isfree(cp,slot) static inline int xfs_lic_isfree(xfs_log_item_chunk_t *cp, int slot) { return (cp->lic_free & (1 << slot)); } -#define XFS_LIC_CLAIM(cp,slot) xfs_lic_claim(cp,slot) static inline void xfs_lic_claim(xfs_log_item_chunk_t *cp, int slot) { cp->lic_free &= ~(1 << slot); } -#define XFS_LIC_RELSE(cp,slot) xfs_lic_relse(cp,slot) static inline void xfs_lic_relse(xfs_log_item_chunk_t *cp, int slot) { cp->lic_free |= 1 << slot; } -#define XFS_LIC_SLOT(cp,slot) xfs_lic_slot(cp,slot) static inline xfs_log_item_desc_t * xfs_lic_slot(xfs_log_item_chunk_t *cp, int slot) { return &(cp->lic_descs[slot]); } -#define XFS_LIC_DESC_TO_SLOT(dp) xfs_lic_desc_to_slot(dp) static inline int xfs_lic_desc_to_slot(xfs_log_item_desc_t *dp) { return (uint)dp->lid_index; @@ -278,7 +268,6 @@ static inline int xfs_lic_desc_to_slot(xfs_log_item_desc_t *dp) * All of this yields the address of the chunk, which is * cast to a chunk pointer. */ -#define XFS_LIC_DESC_TO_CHUNK(dp) xfs_lic_desc_to_chunk(dp) static inline xfs_log_item_chunk_t * xfs_lic_desc_to_chunk(xfs_log_item_desc_t *dp) { diff --git a/fs/xfs/xfs_trans_buf.c b/fs/xfs/xfs_trans_buf.c index cb0c5839154..4e855b5ced6 100644 --- a/fs/xfs/xfs_trans_buf.c +++ b/fs/xfs/xfs_trans_buf.c @@ -1021,16 +1021,16 @@ xfs_trans_buf_item_match( bp = NULL; len = BBTOB(len); licp = &tp->t_items; - if (!XFS_LIC_ARE_ALL_FREE(licp)) { + if (!xfs_lic_are_all_free(licp)) { for (i = 0; i < licp->lic_unused; i++) { /* * Skip unoccupied slots. */ - if (XFS_LIC_ISFREE(licp, i)) { + if (xfs_lic_isfree(licp, i)) { continue; } - lidp = XFS_LIC_SLOT(licp, i); + lidp = xfs_lic_slot(licp, i); blip = (xfs_buf_log_item_t *)lidp->lid_item; if (blip->bli_item.li_type != XFS_LI_BUF) { continue; @@ -1074,7 +1074,7 @@ xfs_trans_buf_item_match_all( bp = NULL; len = BBTOB(len); for (licp = &tp->t_items; licp != NULL; licp = licp->lic_next) { - if (XFS_LIC_ARE_ALL_FREE(licp)) { + if (xfs_lic_are_all_free(licp)) { ASSERT(licp == &tp->t_items); ASSERT(licp->lic_next == NULL); return NULL; @@ -1083,11 +1083,11 @@ xfs_trans_buf_item_match_all( /* * Skip unoccupied slots. */ - if (XFS_LIC_ISFREE(licp, i)) { + if (xfs_lic_isfree(licp, i)) { continue; } - lidp = XFS_LIC_SLOT(licp, i); + lidp = xfs_lic_slot(licp, i); blip = (xfs_buf_log_item_t *)lidp->lid_item; if (blip->bli_item.li_type != XFS_LI_BUF) { continue; diff --git a/fs/xfs/xfs_trans_item.c b/fs/xfs/xfs_trans_item.c index db5c8359552..3c666e8317f 100644 --- a/fs/xfs/xfs_trans_item.c +++ b/fs/xfs/xfs_trans_item.c @@ -53,11 +53,11 @@ xfs_trans_add_item(xfs_trans_t *tp, xfs_log_item_t *lip) * Initialize the chunk, and then * claim the first slot in the newly allocated chunk. */ - XFS_LIC_INIT(licp); - XFS_LIC_CLAIM(licp, 0); + xfs_lic_init(licp); + xfs_lic_claim(licp, 0); licp->lic_unused = 1; - XFS_LIC_INIT_SLOT(licp, 0); - lidp = XFS_LIC_SLOT(licp, 0); + xfs_lic_init_slot(licp, 0); + lidp = xfs_lic_slot(licp, 0); /* * Link in the new chunk and update the free count. @@ -88,14 +88,14 @@ xfs_trans_add_item(xfs_trans_t *tp, xfs_log_item_t *lip) */ licp = &tp->t_items; while (licp != NULL) { - if (XFS_LIC_VACANCY(licp)) { + if (xfs_lic_vacancy(licp)) { if (licp->lic_unused <= XFS_LIC_MAX_SLOT) { i = licp->lic_unused; - ASSERT(XFS_LIC_ISFREE(licp, i)); + ASSERT(xfs_lic_isfree(licp, i)); break; } for (i = 0; i <= XFS_LIC_MAX_SLOT; i++) { - if (XFS_LIC_ISFREE(licp, i)) + if (xfs_lic_isfree(licp, i)) break; } ASSERT(i <= XFS_LIC_MAX_SLOT); @@ -108,12 +108,12 @@ xfs_trans_add_item(xfs_trans_t *tp, xfs_log_item_t *lip) * If we find a free descriptor, claim it, * initialize it, and return it. */ - XFS_LIC_CLAIM(licp, i); + xfs_lic_claim(licp, i); if (licp->lic_unused <= i) { licp->lic_unused = i + 1; - XFS_LIC_INIT_SLOT(licp, i); + xfs_lic_init_slot(licp, i); } - lidp = XFS_LIC_SLOT(licp, i); + lidp = xfs_lic_slot(licp, i); tp->t_items_free--; lidp->lid_item = lip; lidp->lid_flags = 0; @@ -136,9 +136,9 @@ xfs_trans_free_item(xfs_trans_t *tp, xfs_log_item_desc_t *lidp) xfs_log_item_chunk_t *licp; xfs_log_item_chunk_t **licpp; - slot = XFS_LIC_DESC_TO_SLOT(lidp); - licp = XFS_LIC_DESC_TO_CHUNK(lidp); - XFS_LIC_RELSE(licp, slot); + slot = xfs_lic_desc_to_slot(lidp); + licp = xfs_lic_desc_to_chunk(lidp); + xfs_lic_relse(licp, slot); lidp->lid_item->li_desc = NULL; tp->t_items_free++; @@ -154,7 +154,7 @@ xfs_trans_free_item(xfs_trans_t *tp, xfs_log_item_desc_t *lidp) * Also decrement the transaction structure's count of free items * by the number in a chunk since we are freeing an empty chunk. */ - if (XFS_LIC_ARE_ALL_FREE(licp) && (licp != &(tp->t_items))) { + if (xfs_lic_are_all_free(licp) && (licp != &(tp->t_items))) { licpp = &(tp->t_items.lic_next); while (*licpp != licp) { ASSERT(*licpp != NULL); @@ -207,20 +207,20 @@ xfs_trans_first_item(xfs_trans_t *tp) /* * If it's not in the first chunk, skip to the second. */ - if (XFS_LIC_ARE_ALL_FREE(licp)) { + if (xfs_lic_are_all_free(licp)) { licp = licp->lic_next; } /* * Return the first non-free descriptor in the chunk. */ - ASSERT(!XFS_LIC_ARE_ALL_FREE(licp)); + ASSERT(!xfs_lic_are_all_free(licp)); for (i = 0; i < licp->lic_unused; i++) { - if (XFS_LIC_ISFREE(licp, i)) { + if (xfs_lic_isfree(licp, i)) { continue; } - return XFS_LIC_SLOT(licp, i); + return xfs_lic_slot(licp, i); } cmn_err(CE_WARN, "xfs_trans_first_item() -- no first item"); return NULL; @@ -242,18 +242,18 @@ xfs_trans_next_item(xfs_trans_t *tp, xfs_log_item_desc_t *lidp) xfs_log_item_chunk_t *licp; int i; - licp = XFS_LIC_DESC_TO_CHUNK(lidp); + licp = xfs_lic_desc_to_chunk(lidp); /* * First search the rest of the chunk. The for loop keeps us * from referencing things beyond the end of the chunk. */ - for (i = (int)XFS_LIC_DESC_TO_SLOT(lidp) + 1; i < licp->lic_unused; i++) { - if (XFS_LIC_ISFREE(licp, i)) { + for (i = (int)xfs_lic_desc_to_slot(lidp) + 1; i < licp->lic_unused; i++) { + if (xfs_lic_isfree(licp, i)) { continue; } - return XFS_LIC_SLOT(licp, i); + return xfs_lic_slot(licp, i); } /* @@ -266,13 +266,13 @@ xfs_trans_next_item(xfs_trans_t *tp, xfs_log_item_desc_t *lidp) } licp = licp->lic_next; - ASSERT(!XFS_LIC_ARE_ALL_FREE(licp)); + ASSERT(!xfs_lic_are_all_free(licp)); for (i = 0; i < licp->lic_unused; i++) { - if (XFS_LIC_ISFREE(licp, i)) { + if (xfs_lic_isfree(licp, i)) { continue; } - return XFS_LIC_SLOT(licp, i); + return xfs_lic_slot(licp, i); } ASSERT(0); /* NOTREACHED */ @@ -300,9 +300,9 @@ xfs_trans_free_items( /* * Special case the embedded chunk so we don't free it below. */ - if (!XFS_LIC_ARE_ALL_FREE(licp)) { + if (!xfs_lic_are_all_free(licp)) { (void) xfs_trans_unlock_chunk(licp, 1, abort, NULLCOMMITLSN); - XFS_LIC_ALL_FREE(licp); + xfs_lic_all_free(licp); licp->lic_unused = 0; } licp = licp->lic_next; @@ -311,7 +311,7 @@ xfs_trans_free_items( * Unlock each item in each chunk and free the chunks. */ while (licp != NULL) { - ASSERT(!XFS_LIC_ARE_ALL_FREE(licp)); + ASSERT(!xfs_lic_are_all_free(licp)); (void) xfs_trans_unlock_chunk(licp, 1, abort, NULLCOMMITLSN); next_licp = licp->lic_next; kmem_free(licp); @@ -347,7 +347,7 @@ xfs_trans_unlock_items(xfs_trans_t *tp, xfs_lsn_t commit_lsn) /* * Special case the embedded chunk so we don't free. */ - if (!XFS_LIC_ARE_ALL_FREE(licp)) { + if (!xfs_lic_are_all_free(licp)) { freed = xfs_trans_unlock_chunk(licp, 0, 0, commit_lsn); } licpp = &(tp->t_items.lic_next); @@ -358,10 +358,10 @@ xfs_trans_unlock_items(xfs_trans_t *tp, xfs_lsn_t commit_lsn) * and free empty chunks. */ while (licp != NULL) { - ASSERT(!XFS_LIC_ARE_ALL_FREE(licp)); + ASSERT(!xfs_lic_are_all_free(licp)); freed += xfs_trans_unlock_chunk(licp, 0, 0, commit_lsn); next_licp = licp->lic_next; - if (XFS_LIC_ARE_ALL_FREE(licp)) { + if (xfs_lic_are_all_free(licp)) { *licpp = next_licp; kmem_free(licp); freed -= XFS_LIC_NUM_SLOTS; @@ -402,7 +402,7 @@ xfs_trans_unlock_chunk( freed = 0; lidp = licp->lic_descs; for (i = 0; i < licp->lic_unused; i++, lidp++) { - if (XFS_LIC_ISFREE(licp, i)) { + if (xfs_lic_isfree(licp, i)) { continue; } lip = lidp->lid_item; @@ -421,7 +421,7 @@ xfs_trans_unlock_chunk( */ if (!(freeing_chunk) && (!(lidp->lid_flags & XFS_LID_DIRTY) || abort)) { - XFS_LIC_RELSE(licp, i); + xfs_lic_relse(licp, i); freed++; } } -- GitLab From a19d033cd2cc66120f01b370ec081d67b59b7924 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:11:26 +1000 Subject: [PATCH 150/750] [XFS] Remove vn_from_inode() bhv_vnode_t is just a typedef for struct inode, so there's no need for a helper to convert between the two. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31760a Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_super.c | 2 +- fs/xfs/linux-2.6/xfs_vnode.h | 7 +------ 2 files changed, 2 insertions(+), 7 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_super.c b/fs/xfs/linux-2.6/xfs_super.c index 27758409fc8..184ef14856a 100644 --- a/fs/xfs/linux-2.6/xfs_super.c +++ b/fs/xfs/linux-2.6/xfs_super.c @@ -994,7 +994,7 @@ STATIC void xfs_fs_destroy_inode( struct inode *inode) { - kmem_zone_free(xfs_vnode_zone, vn_from_inode(inode)); + kmem_zone_free(xfs_vnode_zone, inode); } STATIC void diff --git a/fs/xfs/linux-2.6/xfs_vnode.h b/fs/xfs/linux-2.6/xfs_vnode.h index c3afecf8c5b..536515cad90 100644 --- a/fs/xfs/linux-2.6/xfs_vnode.h +++ b/fs/xfs/linux-2.6/xfs_vnode.h @@ -27,10 +27,6 @@ typedef struct inode bhv_vnode_t; /* * Vnode to Linux inode mapping. */ -static inline bhv_vnode_t *vn_from_inode(struct inode *inode) -{ - return inode; -} static inline struct inode *vn_to_inode(bhv_vnode_t *vnode) { return vnode; @@ -100,8 +96,7 @@ extern bhv_vnode_t *vn_hold(bhv_vnode_t *); static inline bhv_vnode_t *vn_grab(bhv_vnode_t *vp) { - struct inode *inode = igrab(vn_to_inode(vp)); - return inode ? vn_from_inode(inode) : NULL; + return igrab(vn_to_inode(vp)); } /* -- GitLab From 863890cd90e8b213f7028036c6e2200d93223527 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:12:05 +1000 Subject: [PATCH 151/750] [XFS] kill vn_to_inode bhv_vnode_t is just a typedef for struct inode, so there's no need for a helper to convert between the two. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31761a Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_linux.h | 2 +- fs/xfs/linux-2.6/xfs_super.c | 14 ++++++-------- fs/xfs/linux-2.6/xfs_vnode.c | 2 +- fs/xfs/linux-2.6/xfs_vnode.h | 24 ++++++++---------------- fs/xfs/xfs_vnodeops.c | 4 ++-- 5 files changed, 18 insertions(+), 28 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_linux.h b/fs/xfs/linux-2.6/xfs_linux.h index a9cd6e41052..1b8dfdcac0a 100644 --- a/fs/xfs/linux-2.6/xfs_linux.h +++ b/fs/xfs/linux-2.6/xfs_linux.h @@ -180,7 +180,7 @@ #define xfs_sort(a,n,s,fn) sort(a,n,s,fn,NULL) #define xfs_stack_trace() dump_stack() #define xfs_itruncate_data(ip, off) \ - (-vmtruncate(vn_to_inode(VFS_I(ip)), (off))) + (-vmtruncate(VFS_I(ip), (off))) /* Move the kernel do_div definition off to one side */ diff --git a/fs/xfs/linux-2.6/xfs_super.c b/fs/xfs/linux-2.6/xfs_super.c index 184ef14856a..71ac3a6162e 100644 --- a/fs/xfs/linux-2.6/xfs_super.c +++ b/fs/xfs/linux-2.6/xfs_super.c @@ -613,10 +613,9 @@ xfs_set_inodeops( STATIC_INLINE void xfs_revalidate_inode( xfs_mount_t *mp, - bhv_vnode_t *vp, + struct inode *inode, xfs_inode_t *ip) { - struct inode *inode = vn_to_inode(vp); inode->i_mode = ip->i_d.di_mode; inode->i_nlink = ip->i_d.di_nlink; @@ -665,13 +664,12 @@ xfs_revalidate_inode( void xfs_initialize_vnode( struct xfs_mount *mp, - bhv_vnode_t *vp, + struct inode *inode, struct xfs_inode *ip) { - struct inode *inode = vn_to_inode(vp); if (!ip->i_vnode) { - ip->i_vnode = vp; + ip->i_vnode = inode; inode->i_private = ip; } @@ -683,7 +681,7 @@ xfs_initialize_vnode( * finish our work. */ if (ip->i_d.di_mode != 0 && (inode->i_state & I_NEW)) { - xfs_revalidate_inode(mp, vp, ip); + xfs_revalidate_inode(mp, inode, ip); xfs_set_inodeops(inode); xfs_iflags_clear(ip, XFS_INEW); @@ -987,7 +985,7 @@ xfs_fs_alloc_inode( vp = kmem_zone_alloc(xfs_vnode_zone, KM_SLEEP); if (unlikely(!vp)) return NULL; - return vn_to_inode(vp); + return vp; } STATIC void @@ -1001,7 +999,7 @@ STATIC void xfs_fs_inode_init_once( void *vnode) { - inode_init_once(vn_to_inode((bhv_vnode_t *)vnode)); + inode_init_once((struct inode *)vnode); } /* diff --git a/fs/xfs/linux-2.6/xfs_vnode.c b/fs/xfs/linux-2.6/xfs_vnode.c index 1e39d04c86c..4af972b0166 100644 --- a/fs/xfs/linux-2.6/xfs_vnode.c +++ b/fs/xfs/linux-2.6/xfs_vnode.c @@ -94,7 +94,7 @@ vn_hold( XFS_STATS_INC(vn_hold); - inode = igrab(vn_to_inode(vp)); + inode = igrab(vp); ASSERT(inode); return vp; diff --git a/fs/xfs/linux-2.6/xfs_vnode.h b/fs/xfs/linux-2.6/xfs_vnode.h index 536515cad90..cc53687ff82 100644 --- a/fs/xfs/linux-2.6/xfs_vnode.h +++ b/fs/xfs/linux-2.6/xfs_vnode.h @@ -24,14 +24,6 @@ struct attrlist_cursor_kern; typedef struct inode bhv_vnode_t; -/* - * Vnode to Linux inode mapping. - */ -static inline struct inode *vn_to_inode(bhv_vnode_t *vnode) -{ - return vnode; -} - /* * Return values for xfs_inactive. A return value of * VN_INACTIVE_NOCACHE implies that the file system behavior @@ -74,7 +66,7 @@ extern void vn_ioerror(struct xfs_inode *ip, int error, char *f, int l); static inline int vn_count(bhv_vnode_t *vp) { - return atomic_read(&vn_to_inode(vp)->i_count); + return atomic_read(&vp->i_count); } /* @@ -88,15 +80,15 @@ extern bhv_vnode_t *vn_hold(bhv_vnode_t *); xfs_itrace_hold(XFS_I(vp), __FILE__, __LINE__, (inst_t *)__return_address)) #define VN_RELE(vp) \ (xfs_itrace_rele(XFS_I(vp), __FILE__, __LINE__, (inst_t *)__return_address), \ - iput(vn_to_inode(vp))) + iput(vp)) #else #define VN_HOLD(vp) ((void)vn_hold(vp)) -#define VN_RELE(vp) (iput(vn_to_inode(vp))) +#define VN_RELE(vp) (iput(vp)) #endif static inline bhv_vnode_t *vn_grab(bhv_vnode_t *vp) { - return igrab(vn_to_inode(vp)); + return igrab(vp); } /* @@ -104,7 +96,7 @@ static inline bhv_vnode_t *vn_grab(bhv_vnode_t *vp) */ static inline int VN_BAD(bhv_vnode_t *vp) { - return is_bad_inode(vn_to_inode(vp)); + return is_bad_inode(vp); } /* @@ -129,9 +121,9 @@ static inline void vn_atime_to_time_t(bhv_vnode_t *vp, time_t *tt) /* * Some useful predicates. */ -#define VN_MAPPED(vp) mapping_mapped(vn_to_inode(vp)->i_mapping) -#define VN_CACHED(vp) (vn_to_inode(vp)->i_mapping->nrpages) -#define VN_DIRTY(vp) mapping_tagged(vn_to_inode(vp)->i_mapping, \ +#define VN_MAPPED(vp) mapping_mapped(vp->i_mapping) +#define VN_CACHED(vp) (vp->i_mapping->nrpages) +#define VN_DIRTY(vp) mapping_tagged(vp->i_mapping, \ PAGECACHE_TAG_DIRTY) diff --git a/fs/xfs/xfs_vnodeops.c b/fs/xfs/xfs_vnodeops.c index 35a053fd161..c5dc7ea8526 100644 --- a/fs/xfs/xfs_vnodeops.c +++ b/fs/xfs/xfs_vnodeops.c @@ -714,7 +714,7 @@ xfs_fsync( return XFS_ERROR(EIO); /* capture size updates in I/O completion before writing the inode. */ - error = filemap_fdatawait(vn_to_inode(VFS_I(ip))->i_mapping); + error = filemap_fdatawait(VFS_I(ip)->i_mapping); if (error) return XFS_ERROR(error); @@ -2917,7 +2917,7 @@ xfs_reclaim( XFS_MOUNT_ILOCK(mp); spin_lock(&ip->i_flags_lock); __xfs_iflags_set(ip, XFS_IRECLAIMABLE); - vn_to_inode(vp)->i_private = NULL; + vp->i_private = NULL; ip->i_vnode = NULL; spin_unlock(&ip->i_flags_lock); list_add_tail(&ip->i_reclaim, &mp->m_del_inodes); -- GitLab From 604323ca760beebf00a07153706dcbe7128324e0 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:12:37 +1000 Subject: [PATCH 152/750] [XFS] remove spurious VN_HOLD/VN_RELE calls from xfs_acl.c All the ACL routines are called from inode operations which are guaranteed to have a referenced inode by the VFS, so there's no need for the ACL code to grab another temporary one. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31763a Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/xfs_acl.c | 6 ------ 1 file changed, 6 deletions(-) diff --git a/fs/xfs/xfs_acl.c b/fs/xfs/xfs_acl.c index fdeca54540a..795c81e2525 100644 --- a/fs/xfs/xfs_acl.c +++ b/fs/xfs/xfs_acl.c @@ -217,7 +217,6 @@ xfs_acl_vget( posix_acl_xattr_header *ext_acl = acl; int flags = 0; - VN_HOLD(vp); if(size) { if (!(_ACL_ALLOC(xfs_acl))) { error = ENOMEM; @@ -243,7 +242,6 @@ xfs_acl_vget( error = -posix_acl_xfs_to_xattr(xfs_acl, ext_acl, size); } out: - VN_RELE(vp); if(xfs_acl) _ACL_FREE(xfs_acl); return -error; @@ -256,7 +254,6 @@ xfs_acl_vremove( { int error; - VN_HOLD(vp); error = xfs_acl_allow_set(vp, kind); if (!error) { error = xfs_attr_remove(XFS_I(vp), @@ -266,7 +263,6 @@ xfs_acl_vremove( if (error == ENOATTR) error = 0; /* 'scool */ } - VN_RELE(vp); return -error; } @@ -298,7 +294,6 @@ xfs_acl_vset( return 0; } - VN_HOLD(vp); error = xfs_acl_allow_set(vp, kind); /* Incoming ACL exists, set file mode based on its value */ @@ -321,7 +316,6 @@ xfs_acl_vset( } out: - VN_RELE(vp); _ACL_FREE(xfs_acl); return -error; } -- GitLab From 0b1f917730dc2276fadbd9813ac3666abd7b1cbd Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:13:09 +1000 Subject: [PATCH 153/750] [XFS] remove remaining VN_HOLD calls Use IHOLD(ip) instead of VN_HOLD(VFS_I(ip)). SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31765a Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/quota/xfs_dquot.c | 2 +- fs/xfs/xfs_bmap.c | 2 +- fs/xfs/xfs_dfrag.c | 10 +++------- 3 files changed, 5 insertions(+), 9 deletions(-) diff --git a/fs/xfs/quota/xfs_dquot.c b/fs/xfs/quota/xfs_dquot.c index 68adc5fd9b9..9de42d03174 100644 --- a/fs/xfs/quota/xfs_dquot.c +++ b/fs/xfs/quota/xfs_dquot.c @@ -431,7 +431,7 @@ xfs_qm_dqalloc( * when it unlocks the inode. Since we want to keep the quota * inode around, we bump the vnode ref count now. */ - VN_HOLD(VFS_I(quotip)); + IHOLD(quotip); xfs_trans_ijoin(tp, quotip, XFS_ILOCK_EXCL); nmaps = 1; diff --git a/fs/xfs/xfs_bmap.c b/fs/xfs/xfs_bmap.c index bac82af39a5..3d6a2ce8503 100644 --- a/fs/xfs/xfs_bmap.c +++ b/fs/xfs/xfs_bmap.c @@ -4000,7 +4000,7 @@ xfs_bmap_add_attrfork( ip->i_d.di_aformat = XFS_DINODE_FMT_EXTENTS; } ASSERT(ip->i_d.di_anextents == 0); - VN_HOLD(VFS_I(ip)); + IHOLD(ip); xfs_trans_ijoin(tp, ip, XFS_ILOCK_EXCL); xfs_trans_log_inode(tp, ip, XFS_ILOG_CORE); switch (ip->i_d.di_format) { diff --git a/fs/xfs/xfs_dfrag.c b/fs/xfs/xfs_dfrag.c index 9e751011e23..d92407842e3 100644 --- a/fs/xfs/xfs_dfrag.c +++ b/fs/xfs/xfs_dfrag.c @@ -350,15 +350,11 @@ xfs_swap_extents( break; } - /* - * Increment vnode ref counts since xfs_trans_commit & - * xfs_trans_cancel will both unlock the inodes and - * decrement the associated ref counts. - */ - VN_HOLD(vp); - VN_HOLD(tvp); + IHOLD(ip); xfs_trans_ijoin(tp, ip, lock_flags); + + IHOLD(tip); xfs_trans_ijoin(tp, tip, lock_flags); xfs_trans_log_inode(tp, ip, ilf_fields); -- GitLab From 907f49a8f552acc5d75635e86d567f05daf5c0d8 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:13:45 +1000 Subject: [PATCH 154/750] [XFS] implement IHOLD/IRELE directly Now that all direct calls to VN_HOLD/VN_RELE are gone we can implement IHOLD/IRELE directly. For the IHOLD case also replace igrab with a direct increment of i_count because we are guaranteed to already have a live and referenced inode by the VFS. Also remove the vn_hold statistic because it's been rather meaningless for some time with most references done by other callers. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31764a Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_vnode.c | 18 ------------------ fs/xfs/linux-2.6/xfs_vnode.h | 28 ++++++++++++---------------- fs/xfs/xfs_utils.h | 3 --- 3 files changed, 12 insertions(+), 37 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_vnode.c b/fs/xfs/linux-2.6/xfs_vnode.c index 4af972b0166..1c5a34f5c3c 100644 --- a/fs/xfs/linux-2.6/xfs_vnode.c +++ b/fs/xfs/linux-2.6/xfs_vnode.c @@ -82,24 +82,6 @@ vn_ioerror( xfs_do_force_shutdown(ip->i_mount, SHUTDOWN_DEVICE_REQ, f, l); } - -/* - * Add a reference to a referenced vnode. - */ -bhv_vnode_t * -vn_hold( - bhv_vnode_t *vp) -{ - struct inode *inode; - - XFS_STATS_INC(vn_hold); - - inode = igrab(vp); - ASSERT(inode); - - return vp; -} - #ifdef XFS_INODE_TRACE /* diff --git a/fs/xfs/linux-2.6/xfs_vnode.h b/fs/xfs/linux-2.6/xfs_vnode.h index cc53687ff82..0d7eac03bdf 100644 --- a/fs/xfs/linux-2.6/xfs_vnode.h +++ b/fs/xfs/linux-2.6/xfs_vnode.h @@ -69,22 +69,18 @@ static inline int vn_count(bhv_vnode_t *vp) return atomic_read(&vp->i_count); } -/* - * Vnode reference counting functions (and macros for compatibility). - */ -extern bhv_vnode_t *vn_hold(bhv_vnode_t *); - -#if defined(XFS_INODE_TRACE) -#define VN_HOLD(vp) \ - ((void)vn_hold(vp), \ - xfs_itrace_hold(XFS_I(vp), __FILE__, __LINE__, (inst_t *)__return_address)) -#define VN_RELE(vp) \ - (xfs_itrace_rele(XFS_I(vp), __FILE__, __LINE__, (inst_t *)__return_address), \ - iput(vp)) -#else -#define VN_HOLD(vp) ((void)vn_hold(vp)) -#define VN_RELE(vp) (iput(vp)) -#endif +#define IHOLD(ip) \ +do { \ + ASSERT(atomic_read(&VFS_I(ip)->i_count) > 0) ; \ + atomic_inc(&(VFS_I(ip)->i_count)); \ + xfs_itrace_hold((ip), __FILE__, __LINE__, (inst_t *)__return_address); \ +} while (0) + +#define IRELE(ip) \ +do { \ + xfs_itrace_rele((ip), __FILE__, __LINE__, (inst_t *)__return_address); \ + iput(VFS_I(ip)); \ +} while (0) static inline bhv_vnode_t *vn_grab(bhv_vnode_t *vp) { diff --git a/fs/xfs/xfs_utils.h b/fs/xfs/xfs_utils.h index 7b533dfea60..ef321225d26 100644 --- a/fs/xfs/xfs_utils.h +++ b/fs/xfs/xfs_utils.h @@ -18,9 +18,6 @@ #ifndef __XFS_UTILS_H__ #define __XFS_UTILS_H__ -#define IRELE(ip) VN_RELE(VFS_I(ip)) -#define IHOLD(ip) VN_HOLD(VFS_I(ip)) - extern int xfs_truncate_file(xfs_mount_t *, xfs_inode_t *); extern int xfs_dir_ialloc(xfs_trans_t **, xfs_inode_t *, mode_t, xfs_nlink_t, xfs_dev_t, cred_t *, prid_t, int, -- GitLab From 1550d0b0b08bc34c0c37a86bd884b1a70782104e Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:17:37 +1000 Subject: [PATCH 155/750] [XFS] kill INDUCE_IO_ERROR All the error injection is already enabled through ifdef DEBUG, so kill the never set second cpp symbol to activate it without the rest of the debugging infrastructure. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31771a Signed-off-by: Christoph Hellwig Signed-off-by: Niv Sardi Signed-off-by: Lachlan McIlroy --- fs/xfs/xfs_error.c | 5 +---- fs/xfs/xfs_error.h | 12 ++---------- fs/xfs/xfs_mount.c | 2 +- 3 files changed, 4 insertions(+), 15 deletions(-) diff --git a/fs/xfs/xfs_error.c b/fs/xfs/xfs_error.c index f66756cfb5e..f227ecd1a29 100644 --- a/fs/xfs/xfs_error.c +++ b/fs/xfs/xfs_error.c @@ -58,9 +58,6 @@ xfs_error_trap(int e) } return e; } -#endif - -#if (defined(DEBUG) || defined(INDUCE_IO_ERROR)) int xfs_etest[XFS_NUM_INJECT_ERROR]; int64_t xfs_etest_fsid[XFS_NUM_INJECT_ERROR]; @@ -154,7 +151,7 @@ xfs_errortag_clearall(xfs_mount_t *mp, int loud) return 0; } -#endif /* DEBUG || INDUCE_IO_ERROR */ +#endif /* DEBUG */ static void xfs_fs_vcmn_err(int level, xfs_mount_t *mp, char *fmt, va_list ap) diff --git a/fs/xfs/xfs_error.h b/fs/xfs/xfs_error.h index d8559d132ef..11543f10b0c 100644 --- a/fs/xfs/xfs_error.h +++ b/fs/xfs/xfs_error.h @@ -125,22 +125,14 @@ extern void xfs_corruption_error(char *tag, int level, struct xfs_mount *mp, #define XFS_RANDOM_DIOWRITE_IOERR (XFS_RANDOM_DEFAULT/10) #define XFS_RANDOM_BMAPIFORMAT XFS_RANDOM_DEFAULT -#if (defined(DEBUG) || defined(INDUCE_IO_ERROR)) +#ifdef DEBUG extern int xfs_error_test(int, int *, char *, int, char *, unsigned long); #define XFS_NUM_INJECT_ERROR 10 - -#ifdef __ANSI_CPP__ -#define XFS_TEST_ERROR(expr, mp, tag, rf) \ - ((expr) || \ - xfs_error_test((tag), (mp)->m_fixedfsid, #expr, __LINE__, __FILE__, \ - (rf))) -#else #define XFS_TEST_ERROR(expr, mp, tag, rf) \ ((expr) || \ xfs_error_test((tag), (mp)->m_fixedfsid, "expr", __LINE__, __FILE__, \ (rf))) -#endif /* __ANSI_CPP__ */ extern int xfs_errortag_add(int error_tag, xfs_mount_t *mp); extern int xfs_errortag_clearall(xfs_mount_t *mp, int loud); @@ -148,7 +140,7 @@ extern int xfs_errortag_clearall(xfs_mount_t *mp, int loud); #define XFS_TEST_ERROR(expr, mp, tag, rf) (expr) #define xfs_errortag_add(tag, mp) (ENOSYS) #define xfs_errortag_clearall(mp, loud) (ENOSYS) -#endif /* (DEBUG || INDUCE_IO_ERROR) */ +#endif /* DEBUG */ /* * XFS panic tags -- allow a call to xfs_cmn_err() be turned into diff --git a/fs/xfs/xfs_mount.c b/fs/xfs/xfs_mount.c index 31699b19bb3..6b4350700c0 100644 --- a/fs/xfs/xfs_mount.c +++ b/fs/xfs/xfs_mount.c @@ -1315,7 +1315,7 @@ xfs_unmountfs(xfs_mount_t *mp) if ((mp->m_flags & XFS_MOUNT_NOUUID) == 0) uuid_table_remove(&mp->m_sb.sb_uuid); -#if defined(DEBUG) || defined(INDUCE_IO_ERROR) +#if defined(DEBUG) xfs_errortag_clearall(mp, 0); #endif xfs_mount_free(mp); -- GitLab From e1cccd917be7364f81b5dc4e33ee3a6e0db21a99 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:18:07 +1000 Subject: [PATCH 156/750] [XFS] kill xfs_lock_dir_and_entry When multiple inodes are locked in XFS it happens in order of the inode number, with the everything but the first inode trylocked if any of the previous inodes is in the AIL. Except for the sorting of the inodes this logic is implemented in xfs_lock_inodes, but also partially duplicated in xfs_lock_dir_and_entry in a particularly stupid way adds a lock roundtrip if the inode ordering is not optimal. This patch adds a new helper xfs_lock_two_inodes that takes two inodes and locks them in the most optimal way according to the above locking protocol and uses it for all places that want to lock two inodes. The only caller of xfs_lock_inodes is xfs_rename which might lock up to four inodes. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31772a Signed-off-by: Christoph Hellwig Signed-off-by: Donald Douwsma Signed-off-by: Lachlan McIlroy --- fs/xfs/xfs_dfrag.c | 14 +--- fs/xfs/xfs_inode.h | 1 + fs/xfs/xfs_vnodeops.c | 162 +++++++++++------------------------------- 3 files changed, 44 insertions(+), 133 deletions(-) diff --git a/fs/xfs/xfs_dfrag.c b/fs/xfs/xfs_dfrag.c index d92407842e3..5ce91a00425 100644 --- a/fs/xfs/xfs_dfrag.c +++ b/fs/xfs/xfs_dfrag.c @@ -128,7 +128,6 @@ xfs_swap_extents( xfs_swapext_t *sxp) { xfs_mount_t *mp; - xfs_inode_t *ips[2]; xfs_trans_t *tp; xfs_bstat_t *sbp = &sxp->sx_stat; bhv_vnode_t *vp, *tvp; @@ -153,16 +152,7 @@ xfs_swap_extents( vp = VFS_I(ip); tvp = VFS_I(tip); - /* Lock in i_ino order */ - if (ip->i_ino < tip->i_ino) { - ips[0] = ip; - ips[1] = tip; - } else { - ips[0] = tip; - ips[1] = ip; - } - - xfs_lock_inodes(ips, 2, lock_flags); + xfs_lock_two_inodes(ip, tip, lock_flags); locked = 1; /* Verify that both files have the same format */ @@ -265,7 +255,7 @@ xfs_swap_extents( locked = 0; goto error0; } - xfs_lock_inodes(ips, 2, XFS_ILOCK_EXCL); + xfs_lock_two_inodes(ip, tip, XFS_ILOCK_EXCL); /* * Count the number of extended attribute blocks diff --git a/fs/xfs/xfs_inode.h b/fs/xfs/xfs_inode.h index 4088951230a..ec9f454b464 100644 --- a/fs/xfs/xfs_inode.h +++ b/fs/xfs/xfs_inode.h @@ -531,6 +531,7 @@ void xfs_iflush_all(struct xfs_mount *); void xfs_ichgtime(xfs_inode_t *, int); xfs_fsize_t xfs_file_last_byte(xfs_inode_t *); void xfs_lock_inodes(xfs_inode_t **, int, uint); +void xfs_lock_two_inodes(xfs_inode_t *, xfs_inode_t *, uint); void xfs_synchronize_atime(xfs_inode_t *); void xfs_mark_inode_dirty_sync(xfs_inode_t *); diff --git a/fs/xfs/xfs_vnodeops.c b/fs/xfs/xfs_vnodeops.c index c5dc7ea8526..077c86b6cb2 100644 --- a/fs/xfs/xfs_vnodeops.c +++ b/fs/xfs/xfs_vnodeops.c @@ -1707,111 +1707,6 @@ std_return: goto std_return; } -#ifdef DEBUG -/* - * Some counters to see if (and how often) we are hitting some deadlock - * prevention code paths. - */ - -int xfs_rm_locks; -int xfs_rm_lock_delays; -int xfs_rm_attempts; -#endif - -/* - * The following routine will lock the inodes associated with the - * directory and the named entry in the directory. The locks are - * acquired in increasing inode number. - * - * If the entry is "..", then only the directory is locked. The - * vnode ref count will still include that from the .. entry in - * this case. - * - * There is a deadlock we need to worry about. If the locked directory is - * in the AIL, it might be blocking up the log. The next inode we lock - * could be already locked by another thread waiting for log space (e.g - * a permanent log reservation with a long running transaction (see - * xfs_itruncate_finish)). To solve this, we must check if the directory - * is in the ail and use lock_nowait. If we can't lock, we need to - * drop the inode lock on the directory and try again. xfs_iunlock will - * potentially push the tail if we were holding up the log. - */ -STATIC int -xfs_lock_dir_and_entry( - xfs_inode_t *dp, - xfs_inode_t *ip) /* inode of entry 'name' */ -{ - int attempts; - xfs_ino_t e_inum; - xfs_inode_t *ips[2]; - xfs_log_item_t *lp; - -#ifdef DEBUG - xfs_rm_locks++; -#endif - attempts = 0; - -again: - xfs_ilock(dp, XFS_ILOCK_EXCL | XFS_ILOCK_PARENT); - - e_inum = ip->i_ino; - - xfs_itrace_ref(ip); - - /* - * We want to lock in increasing inum. Since we've already - * acquired the lock on the directory, we may need to release - * if if the inum of the entry turns out to be less. - */ - if (e_inum > dp->i_ino) { - /* - * We are already in the right order, so just - * lock on the inode of the entry. - * We need to use nowait if dp is in the AIL. - */ - - lp = (xfs_log_item_t *)dp->i_itemp; - if (lp && (lp->li_flags & XFS_LI_IN_AIL)) { - if (!xfs_ilock_nowait(ip, XFS_ILOCK_EXCL)) { - attempts++; -#ifdef DEBUG - xfs_rm_attempts++; -#endif - - /* - * Unlock dp and try again. - * xfs_iunlock will try to push the tail - * if the inode is in the AIL. - */ - - xfs_iunlock(dp, XFS_ILOCK_EXCL); - - if ((attempts % 5) == 0) { - delay(1); /* Don't just spin the CPU */ -#ifdef DEBUG - xfs_rm_lock_delays++; -#endif - } - goto again; - } - } else { - xfs_ilock(ip, XFS_ILOCK_EXCL); - } - } else if (e_inum < dp->i_ino) { - xfs_iunlock(dp, XFS_ILOCK_EXCL); - - ips[0] = ip; - ips[1] = dp; - xfs_lock_inodes(ips, 2, XFS_ILOCK_EXCL); - } - /* else e_inum == dp->i_ino */ - /* This can happen if we're asked to lock /x/.. - * the entry is "..", which is also the parent directory. - */ - - return 0; -} - #ifdef DEBUG int xfs_locked_n; int xfs_small_retries; @@ -1946,6 +1841,45 @@ again: #endif } +void +xfs_lock_two_inodes( + xfs_inode_t *ip0, + xfs_inode_t *ip1, + uint lock_mode) +{ + xfs_inode_t *temp; + int attempts = 0; + xfs_log_item_t *lp; + + ASSERT(ip0->i_ino != ip1->i_ino); + + if (ip0->i_ino > ip1->i_ino) { + temp = ip0; + ip0 = ip1; + ip1 = temp; + } + + again: + xfs_ilock(ip0, xfs_lock_inumorder(lock_mode, 0)); + + /* + * If the first lock we have locked is in the AIL, we must TRY to get + * the second lock. If we can't get it, we must release the first one + * and try again. + */ + lp = (xfs_log_item_t *)ip0->i_itemp; + if (lp && (lp->li_flags & XFS_LI_IN_AIL)) { + if (!xfs_ilock_nowait(ip1, xfs_lock_inumorder(lock_mode, 1))) { + xfs_iunlock(ip0, lock_mode); + if ((++attempts % 5) == 0) + delay(1); /* Don't just spin the CPU */ + goto again; + } + } else { + xfs_ilock(ip1, xfs_lock_inumorder(lock_mode, 1)); + } +} + int xfs_remove( xfs_inode_t *dp, @@ -2018,9 +1952,7 @@ xfs_remove( goto out_trans_cancel; } - error = xfs_lock_dir_and_entry(dp, ip); - if (error) - goto out_trans_cancel; + xfs_lock_two_inodes(dp, ip, XFS_ILOCK_EXCL); /* * At this point, we've gotten both the directory and the entry @@ -2047,9 +1979,6 @@ xfs_remove( } } - /* - * Entry must exist since we did a lookup in xfs_lock_dir_and_entry. - */ XFS_BMAP_INIT(&free_list, &first_block); error = xfs_dir_removename(tp, dp, name, ip->i_ino, &first_block, &free_list, resblks); @@ -2155,7 +2084,6 @@ xfs_link( { xfs_mount_t *mp = tdp->i_mount; xfs_trans_t *tp; - xfs_inode_t *ips[2]; int error; xfs_bmap_free_t free_list; xfs_fsblock_t first_block; @@ -2203,15 +2131,7 @@ xfs_link( goto error_return; } - if (sip->i_ino < tdp->i_ino) { - ips[0] = sip; - ips[1] = tdp; - } else { - ips[0] = tdp; - ips[1] = sip; - } - - xfs_lock_inodes(ips, 2, XFS_ILOCK_EXCL); + xfs_lock_two_inodes(sip, tdp, XFS_ILOCK_EXCL); /* * Increment vnode ref counts since xfs_trans_commit & -- GitLab From df80c933f9eb01a7af3812bbe437e38205386304 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:22:09 +1000 Subject: [PATCH 157/750] [XFS] remove some easy bhv_vnode_t instances In various places we can just move a VFS_I call into the argument list of called functions/macros instead of having a local bhv_vnode_t. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31776a Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_super.c | 7 +------ fs/xfs/xfs_dfrag.c | 9 +++------ fs/xfs/xfs_inode.c | 10 +++------- fs/xfs/xfs_itable.c | 4 +--- fs/xfs/xfs_vfsops.c | 3 +-- fs/xfs/xfs_vnodeops.c | 21 ++++++++------------- 6 files changed, 17 insertions(+), 37 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_super.c b/fs/xfs/linux-2.6/xfs_super.c index 71ac3a6162e..1ca593fb122 100644 --- a/fs/xfs/linux-2.6/xfs_super.c +++ b/fs/xfs/linux-2.6/xfs_super.c @@ -980,12 +980,7 @@ STATIC struct inode * xfs_fs_alloc_inode( struct super_block *sb) { - bhv_vnode_t *vp; - - vp = kmem_zone_alloc(xfs_vnode_zone, KM_SLEEP); - if (unlikely(!vp)) - return NULL; - return vp; + return kmem_zone_alloc(xfs_vnode_zone, KM_SLEEP); } STATIC void diff --git a/fs/xfs/xfs_dfrag.c b/fs/xfs/xfs_dfrag.c index 5ce91a00425..760f4c5b516 100644 --- a/fs/xfs/xfs_dfrag.c +++ b/fs/xfs/xfs_dfrag.c @@ -130,7 +130,6 @@ xfs_swap_extents( xfs_mount_t *mp; xfs_trans_t *tp; xfs_bstat_t *sbp = &sxp->sx_stat; - bhv_vnode_t *vp, *tvp; xfs_ifork_t *tempifp, *ifp, *tifp; int ilf_fields, tilf_fields; static uint lock_flags = XFS_ILOCK_EXCL | XFS_IOLOCK_EXCL; @@ -149,8 +148,6 @@ xfs_swap_extents( } sbp = &sxp->sx_stat; - vp = VFS_I(ip); - tvp = VFS_I(tip); xfs_lock_two_inodes(ip, tip, lock_flags); locked = 1; @@ -174,7 +171,7 @@ xfs_swap_extents( goto error0; } - if (VN_CACHED(tvp) != 0) { + if (VN_CACHED(VFS_I(tip)) != 0) { xfs_inval_cached_trace(tip, 0, -1, 0, -1); error = xfs_flushinval_pages(tip, 0, -1, FI_REMAPF_LOCKED); @@ -183,7 +180,7 @@ xfs_swap_extents( } /* Verify O_DIRECT for ftmp */ - if (VN_CACHED(tvp) != 0) { + if (VN_CACHED(VFS_I(tip)) != 0) { error = XFS_ERROR(EINVAL); goto error0; } @@ -227,7 +224,7 @@ xfs_swap_extents( * vop_read (or write in the case of autogrow) they block on the iolock * until we have switched the extents. */ - if (VN_MAPPED(vp)) { + if (VN_MAPPED(VFS_I(ip))) { error = XFS_ERROR(EBUSY); goto error0; } diff --git a/fs/xfs/xfs_inode.c b/fs/xfs/xfs_inode.c index 8da67d5717c..efac8857ccb 100644 --- a/fs/xfs/xfs_inode.c +++ b/fs/xfs/xfs_inode.c @@ -1399,7 +1399,6 @@ xfs_itruncate_start( xfs_fsize_t last_byte; xfs_off_t toss_start; xfs_mount_t *mp; - bhv_vnode_t *vp; int error = 0; ASSERT(xfs_isilocked(ip, XFS_IOLOCK_EXCL)); @@ -1408,7 +1407,6 @@ xfs_itruncate_start( (flags == XFS_ITRUNC_MAYBE)); mp = ip->i_mount; - vp = VFS_I(ip); /* wait for the completion of any pending DIOs */ if (new_size < ip->i_size) @@ -1457,7 +1455,7 @@ xfs_itruncate_start( #ifdef DEBUG if (new_size == 0) { - ASSERT(VN_CACHED(vp) == 0); + ASSERT(VN_CACHED(VFS_I(ip)) == 0); } #endif return error; @@ -3465,7 +3463,6 @@ xfs_iflush_all( xfs_mount_t *mp) { xfs_inode_t *ip; - bhv_vnode_t *vp; again: XFS_MOUNT_ILOCK(mp); @@ -3480,14 +3477,13 @@ xfs_iflush_all( continue; } - vp = VFS_I(ip); - if (!vp) { + if (!VFS_I(ip)) { XFS_MOUNT_IUNLOCK(mp); xfs_finish_reclaim(ip, 0, XFS_IFLUSH_ASYNC); goto again; } - ASSERT(vn_count(vp) == 0); + ASSERT(vn_count(VFS_I(ip)) == 0); ip = ip->i_mnext; } while (ip != mp->m_inodes); diff --git a/fs/xfs/xfs_itable.c b/fs/xfs/xfs_itable.c index 4feda541e71..cf6754a3c5b 100644 --- a/fs/xfs/xfs_itable.c +++ b/fs/xfs/xfs_itable.c @@ -59,7 +59,6 @@ xfs_bulkstat_one_iget( { xfs_icdinode_t *dic; /* dinode core info pointer */ xfs_inode_t *ip; /* incore inode pointer */ - bhv_vnode_t *vp; int error; error = xfs_iget(mp, NULL, ino, @@ -72,7 +71,6 @@ xfs_bulkstat_one_iget( ASSERT(ip != NULL); ASSERT(ip->i_blkno != (xfs_daddr_t)0); - vp = VFS_I(ip); dic = &ip->i_d; /* xfs_iget returns the following without needing @@ -85,7 +83,7 @@ xfs_bulkstat_one_iget( buf->bs_uid = dic->di_uid; buf->bs_gid = dic->di_gid; buf->bs_size = dic->di_size; - vn_atime_to_bstime(vp, &buf->bs_atime); + vn_atime_to_bstime(VFS_I(ip), &buf->bs_atime); buf->bs_mtime.tv_sec = dic->di_mtime.t_sec; buf->bs_mtime.tv_nsec = dic->di_mtime.t_nsec; buf->bs_ctime.tv_sec = dic->di_ctime.t_sec; diff --git a/fs/xfs/xfs_vfsops.c b/fs/xfs/xfs_vfsops.c index 38450f1fa2a..974d3c0b8b6 100644 --- a/fs/xfs/xfs_vfsops.c +++ b/fs/xfs/xfs_vfsops.c @@ -128,7 +128,6 @@ xfs_unmount_flush( xfs_inode_t *rip = mp->m_rootip; xfs_inode_t *rbmip; xfs_inode_t *rsumip = NULL; - bhv_vnode_t *rvp = VFS_I(rip); int error; xfs_ilock(rip, XFS_ILOCK_EXCL | XFS_ILOCK_PARENT); @@ -167,7 +166,7 @@ xfs_unmount_flush( if (error == EFSCORRUPTED) goto fscorrupt_out2; - if (vn_count(rvp) != 1 && !relocation) { + if (vn_count(VFS_I(rip)) != 1 && !relocation) { xfs_iunlock(rip, XFS_ILOCK_EXCL); return XFS_ERROR(EBUSY); } diff --git a/fs/xfs/xfs_vnodeops.c b/fs/xfs/xfs_vnodeops.c index 077c86b6cb2..21da312dd8b 100644 --- a/fs/xfs/xfs_vnodeops.c +++ b/fs/xfs/xfs_vnodeops.c @@ -1160,7 +1160,6 @@ int xfs_release( xfs_inode_t *ip) { - bhv_vnode_t *vp = VFS_I(ip); xfs_mount_t *mp = ip->i_mount; int error; @@ -1195,13 +1194,13 @@ xfs_release( * be exposed to that problem. */ truncated = xfs_iflags_test_and_clear(ip, XFS_ITRUNCATED); - if (truncated && VN_DIRTY(vp) && ip->i_delayed_blks > 0) + if (truncated && VN_DIRTY(VFS_I(ip)) && ip->i_delayed_blks > 0) xfs_flush_pages(ip, 0, -1, XFS_B_ASYNC, FI_NONE); } if (ip->i_d.di_nlink != 0) { if ((((ip->i_d.di_mode & S_IFMT) == S_IFREG) && - ((ip->i_size > 0) || (VN_CACHED(vp) > 0 || + ((ip->i_size > 0) || (VN_CACHED(VFS_I(ip)) > 0 || ip->i_delayed_blks > 0)) && (ip->i_df.if_flags & XFS_IFEXTENTS)) && (!(ip->i_d.di_flags & @@ -1227,7 +1226,6 @@ int xfs_inactive( xfs_inode_t *ip) { - bhv_vnode_t *vp = VFS_I(ip); xfs_bmap_free_t free_list; xfs_fsblock_t first_block; int committed; @@ -1242,7 +1240,7 @@ xfs_inactive( * If the inode is already free, then there can be nothing * to clean up here. */ - if (ip->i_d.di_mode == 0 || VN_BAD(vp)) { + if (ip->i_d.di_mode == 0 || VN_BAD(VFS_I(ip))) { ASSERT(ip->i_df.if_real_bytes == 0); ASSERT(ip->i_df.if_broot_bytes == 0); return VN_INACTIVE_CACHE; @@ -1272,7 +1270,7 @@ xfs_inactive( if (ip->i_d.di_nlink != 0) { if ((((ip->i_d.di_mode & S_IFMT) == S_IFREG) && - ((ip->i_size > 0) || (VN_CACHED(vp) > 0 || + ((ip->i_size > 0) || (VN_CACHED(VFS_I(ip)) > 0 || ip->i_delayed_blks > 0)) && (ip->i_df.if_flags & XFS_IFEXTENTS) && (!(ip->i_d.di_flags & @@ -2793,14 +2791,13 @@ int xfs_reclaim( xfs_inode_t *ip) { - bhv_vnode_t *vp = VFS_I(ip); xfs_itrace_entry(ip); - ASSERT(!VN_MAPPED(vp)); + ASSERT(!VN_MAPPED(VFS_I(ip))); /* bad inode, get out here ASAP */ - if (VN_BAD(vp)) { + if (VN_BAD(VFS_I(ip))) { xfs_ireclaim(ip); return 0; } @@ -2837,7 +2834,7 @@ xfs_reclaim( XFS_MOUNT_ILOCK(mp); spin_lock(&ip->i_flags_lock); __xfs_iflags_set(ip, XFS_IRECLAIMABLE); - vp->i_private = NULL; + VFS_I(ip)->i_private = NULL; ip->i_vnode = NULL; spin_unlock(&ip->i_flags_lock); list_add_tail(&ip->i_reclaim, &mp->m_del_inodes); @@ -3241,7 +3238,6 @@ xfs_free_file_space( xfs_off_t len, int attr_flags) { - bhv_vnode_t *vp; int committed; int done; xfs_off_t end_dmi_offset; @@ -3261,7 +3257,6 @@ xfs_free_file_space( xfs_trans_t *tp; int need_iolock = 1; - vp = VFS_I(ip); mp = ip->i_mount; xfs_itrace_entry(ip); @@ -3298,7 +3293,7 @@ xfs_free_file_space( rounding = max_t(uint, 1 << mp->m_sb.sb_blocklog, PAGE_CACHE_SIZE); ioffset = offset & ~(rounding - 1); - if (VN_CACHED(vp) != 0) { + if (VN_CACHED(VFS_I(ip)) != 0) { xfs_inval_cached_trace(ip, ioffset, -1, ioffset, -1); error = xfs_flushinval_pages(ip, ioffset, -1, FI_REMAPF_LOCKED); if (error) -- GitLab From 5ec7f8c7d14a3ea6bf920b3350f5c5d3527cb837 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:22:40 +1000 Subject: [PATCH 158/750] [XFS] kill bhv_vnode_t All remaining bhv_vnode_t instance are in code that's more or less Linux specific. (Well, for xfs_acl.c that could be argued, but that code is on the removal list, too). So just do an s/bhv_vnode_t/struct inode/ over the whole tree. We can clean up variable naming and some useless helpers later. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31781a Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_super.c | 2 +- fs/xfs/linux-2.6/xfs_super.h | 2 +- fs/xfs/linux-2.6/xfs_vnode.c | 2 +- fs/xfs/linux-2.6/xfs_vnode.h | 14 ++++++-------- fs/xfs/quota/xfs_qm_syscalls.c | 2 +- fs/xfs/xfs_acl.c | 30 +++++++++++++++--------------- fs/xfs/xfs_acl.h | 14 +++++++------- fs/xfs/xfs_inode.c | 2 +- fs/xfs/xfs_inode.h | 2 +- fs/xfs/xfs_vfsops.c | 2 +- fs/xfs/xfs_vnodeops.c | 2 +- 11 files changed, 36 insertions(+), 38 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_super.c b/fs/xfs/linux-2.6/xfs_super.c index 1ca593fb122..7605b071dc8 100644 --- a/fs/xfs/linux-2.6/xfs_super.c +++ b/fs/xfs/linux-2.6/xfs_super.c @@ -2038,7 +2038,7 @@ xfs_free_trace_bufs(void) STATIC int __init xfs_init_zones(void) { - xfs_vnode_zone = kmem_zone_init_flags(sizeof(bhv_vnode_t), "xfs_vnode", + xfs_vnode_zone = kmem_zone_init_flags(sizeof(struct inode), "xfs_vnode", KM_ZONE_HWALIGN | KM_ZONE_RECLAIM | KM_ZONE_SPREAD, xfs_fs_inode_init_once); diff --git a/fs/xfs/linux-2.6/xfs_super.h b/fs/xfs/linux-2.6/xfs_super.h index b7d13da01bd..57145fff385 100644 --- a/fs/xfs/linux-2.6/xfs_super.h +++ b/fs/xfs/linux-2.6/xfs_super.h @@ -101,7 +101,7 @@ struct block_device; extern __uint64_t xfs_max_file_offset(unsigned int); -extern void xfs_initialize_vnode(struct xfs_mount *mp, bhv_vnode_t *vp, +extern void xfs_initialize_vnode(struct xfs_mount *mp, struct inode *vp, struct xfs_inode *ip); extern void xfs_flush_inode(struct xfs_inode *); diff --git a/fs/xfs/linux-2.6/xfs_vnode.c b/fs/xfs/linux-2.6/xfs_vnode.c index 1c5a34f5c3c..5cad3274db0 100644 --- a/fs/xfs/linux-2.6/xfs_vnode.c +++ b/fs/xfs/linux-2.6/xfs_vnode.c @@ -90,7 +90,7 @@ vn_ioerror( */ static inline int xfs_icount(struct xfs_inode *ip) { - bhv_vnode_t *vp = VFS_I(ip); + struct inode *vp = VFS_I(ip); if (vp) return vn_count(vp); diff --git a/fs/xfs/linux-2.6/xfs_vnode.h b/fs/xfs/linux-2.6/xfs_vnode.h index 0d7eac03bdf..683ce16210f 100644 --- a/fs/xfs/linux-2.6/xfs_vnode.h +++ b/fs/xfs/linux-2.6/xfs_vnode.h @@ -22,8 +22,6 @@ struct file; struct xfs_iomap; struct attrlist_cursor_kern; -typedef struct inode bhv_vnode_t; - /* * Return values for xfs_inactive. A return value of * VN_INACTIVE_NOCACHE implies that the file system behavior @@ -64,7 +62,7 @@ extern void vn_iowait(struct xfs_inode *ip); extern void vn_iowake(struct xfs_inode *ip); extern void vn_ioerror(struct xfs_inode *ip, int error, char *f, int l); -static inline int vn_count(bhv_vnode_t *vp) +static inline int vn_count(struct inode *vp) { return atomic_read(&vp->i_count); } @@ -82,7 +80,7 @@ do { \ iput(VFS_I(ip)); \ } while (0) -static inline bhv_vnode_t *vn_grab(bhv_vnode_t *vp) +static inline struct inode *vn_grab(struct inode *vp) { return igrab(vp); } @@ -90,7 +88,7 @@ static inline bhv_vnode_t *vn_grab(bhv_vnode_t *vp) /* * Dealing with bad inodes */ -static inline int VN_BAD(bhv_vnode_t *vp) +static inline int VN_BAD(struct inode *vp) { return is_bad_inode(vp); } @@ -98,18 +96,18 @@ static inline int VN_BAD(bhv_vnode_t *vp) /* * Extracting atime values in various formats */ -static inline void vn_atime_to_bstime(bhv_vnode_t *vp, xfs_bstime_t *bs_atime) +static inline void vn_atime_to_bstime(struct inode *vp, xfs_bstime_t *bs_atime) { bs_atime->tv_sec = vp->i_atime.tv_sec; bs_atime->tv_nsec = vp->i_atime.tv_nsec; } -static inline void vn_atime_to_timespec(bhv_vnode_t *vp, struct timespec *ts) +static inline void vn_atime_to_timespec(struct inode *vp, struct timespec *ts) { *ts = vp->i_atime; } -static inline void vn_atime_to_time_t(bhv_vnode_t *vp, time_t *tt) +static inline void vn_atime_to_time_t(struct inode *vp, time_t *tt) { *tt = vp->i_atime.tv_sec; } diff --git a/fs/xfs/quota/xfs_qm_syscalls.c b/fs/xfs/quota/xfs_qm_syscalls.c index 132a0abb2f0..1a3b803dfa5 100644 --- a/fs/xfs/quota/xfs_qm_syscalls.c +++ b/fs/xfs/quota/xfs_qm_syscalls.c @@ -1034,7 +1034,7 @@ xfs_qm_dqrele_all_inodes( { xfs_inode_t *ip, *topino; uint ireclaims; - bhv_vnode_t *vp; + struct inode *vp; boolean_t vnode_refd; ASSERT(mp->m_quotainfo); diff --git a/fs/xfs/xfs_acl.c b/fs/xfs/xfs_acl.c index 795c81e2525..b2f639a1416 100644 --- a/fs/xfs/xfs_acl.c +++ b/fs/xfs/xfs_acl.c @@ -37,15 +37,15 @@ #include #include -STATIC int xfs_acl_setmode(bhv_vnode_t *, xfs_acl_t *, int *); +STATIC int xfs_acl_setmode(struct inode *, xfs_acl_t *, int *); STATIC void xfs_acl_filter_mode(mode_t, xfs_acl_t *); STATIC void xfs_acl_get_endian(xfs_acl_t *); STATIC int xfs_acl_access(uid_t, gid_t, xfs_acl_t *, mode_t, cred_t *); STATIC int xfs_acl_invalid(xfs_acl_t *); STATIC void xfs_acl_sync_mode(mode_t, xfs_acl_t *); -STATIC void xfs_acl_get_attr(bhv_vnode_t *, xfs_acl_t *, int, int, int *); -STATIC void xfs_acl_set_attr(bhv_vnode_t *, xfs_acl_t *, int, int *); -STATIC int xfs_acl_allow_set(bhv_vnode_t *, int); +STATIC void xfs_acl_get_attr(struct inode *, xfs_acl_t *, int, int, int *); +STATIC void xfs_acl_set_attr(struct inode *, xfs_acl_t *, int, int *); +STATIC int xfs_acl_allow_set(struct inode *, int); kmem_zone_t *xfs_acl_zone; @@ -55,7 +55,7 @@ kmem_zone_t *xfs_acl_zone; */ int xfs_acl_vhasacl_access( - bhv_vnode_t *vp) + struct inode *vp) { int error; @@ -68,7 +68,7 @@ xfs_acl_vhasacl_access( */ int xfs_acl_vhasacl_default( - bhv_vnode_t *vp) + struct inode *vp) { int error; @@ -207,7 +207,7 @@ posix_acl_xfs_to_xattr( int xfs_acl_vget( - bhv_vnode_t *vp, + struct inode *vp, void *acl, size_t size, int kind) @@ -249,7 +249,7 @@ out: int xfs_acl_vremove( - bhv_vnode_t *vp, + struct inode *vp, int kind) { int error; @@ -268,7 +268,7 @@ xfs_acl_vremove( int xfs_acl_vset( - bhv_vnode_t *vp, + struct inode *vp, void *acl, size_t size, int kind) @@ -357,7 +357,7 @@ xfs_acl_iaccess( STATIC int xfs_acl_allow_set( - bhv_vnode_t *vp, + struct inode *vp, int kind) { if (vp->i_flags & (S_IMMUTABLE|S_APPEND)) @@ -560,7 +560,7 @@ xfs_acl_get_endian( */ STATIC void xfs_acl_get_attr( - bhv_vnode_t *vp, + struct inode *vp, xfs_acl_t *aclp, int kind, int flags, @@ -584,7 +584,7 @@ xfs_acl_get_attr( */ STATIC void xfs_acl_set_attr( - bhv_vnode_t *vp, + struct inode *vp, xfs_acl_t *aclp, int kind, int *error) @@ -618,7 +618,7 @@ xfs_acl_set_attr( int xfs_acl_vtoacl( - bhv_vnode_t *vp, + struct inode *vp, xfs_acl_t *access_acl, xfs_acl_t *default_acl) { @@ -650,7 +650,7 @@ xfs_acl_vtoacl( */ int xfs_acl_inherit( - bhv_vnode_t *vp, + struct inode *vp, mode_t mode, xfs_acl_t *pdaclp) { @@ -709,7 +709,7 @@ out_error: */ STATIC int xfs_acl_setmode( - bhv_vnode_t *vp, + struct inode *vp, xfs_acl_t *acl, int *basicperms) { diff --git a/fs/xfs/xfs_acl.h b/fs/xfs/xfs_acl.h index 323ee94cf83..a4e293b93ef 100644 --- a/fs/xfs/xfs_acl.h +++ b/fs/xfs/xfs_acl.h @@ -59,14 +59,14 @@ extern struct kmem_zone *xfs_acl_zone; (zone) = kmem_zone_init(sizeof(xfs_acl_t), (name)) #define xfs_acl_zone_destroy(zone) kmem_zone_destroy(zone) -extern int xfs_acl_inherit(bhv_vnode_t *, mode_t mode, xfs_acl_t *); +extern int xfs_acl_inherit(struct inode *, mode_t mode, xfs_acl_t *); extern int xfs_acl_iaccess(struct xfs_inode *, mode_t, cred_t *); -extern int xfs_acl_vtoacl(bhv_vnode_t *, xfs_acl_t *, xfs_acl_t *); -extern int xfs_acl_vhasacl_access(bhv_vnode_t *); -extern int xfs_acl_vhasacl_default(bhv_vnode_t *); -extern int xfs_acl_vset(bhv_vnode_t *, void *, size_t, int); -extern int xfs_acl_vget(bhv_vnode_t *, void *, size_t, int); -extern int xfs_acl_vremove(bhv_vnode_t *, int); +extern int xfs_acl_vtoacl(struct inode *, xfs_acl_t *, xfs_acl_t *); +extern int xfs_acl_vhasacl_access(struct inode *); +extern int xfs_acl_vhasacl_default(struct inode *); +extern int xfs_acl_vset(struct inode *, void *, size_t, int); +extern int xfs_acl_vget(struct inode *, void *, size_t, int); +extern int xfs_acl_vremove(struct inode *, int); #define _ACL_PERM_INVALID(perm) ((perm) & ~(ACL_READ|ACL_WRITE|ACL_EXECUTE)) diff --git a/fs/xfs/xfs_inode.c b/fs/xfs/xfs_inode.c index efac8857ccb..19e7a7b8270 100644 --- a/fs/xfs/xfs_inode.c +++ b/fs/xfs/xfs_inode.c @@ -1046,7 +1046,7 @@ xfs_ialloc( { xfs_ino_t ino; xfs_inode_t *ip; - bhv_vnode_t *vp; + struct inode *vp; uint flags; int error; diff --git a/fs/xfs/xfs_inode.h b/fs/xfs/xfs_inode.h index ec9f454b464..57172440435 100644 --- a/fs/xfs/xfs_inode.h +++ b/fs/xfs/xfs_inode.h @@ -204,7 +204,7 @@ typedef struct xfs_inode { struct xfs_inode *i_mprev; /* ptr to prev inode */ struct xfs_mount *i_mount; /* fs mount struct ptr */ struct list_head i_reclaim; /* reclaim list */ - bhv_vnode_t *i_vnode; /* vnode backpointer */ + struct inode *i_vnode; /* vnode backpointer */ struct xfs_dquot *i_udquot; /* user dquot */ struct xfs_dquot *i_gdquot; /* group dquot */ diff --git a/fs/xfs/xfs_vfsops.c b/fs/xfs/xfs_vfsops.c index 974d3c0b8b6..439dd3939dd 100644 --- a/fs/xfs/xfs_vfsops.c +++ b/fs/xfs/xfs_vfsops.c @@ -283,7 +283,7 @@ xfs_sync_inodes( int *bypassed) { xfs_inode_t *ip = NULL; - bhv_vnode_t *vp = NULL; + struct inode *vp = NULL; int error; int last_error; uint64_t fflag; diff --git a/fs/xfs/xfs_vnodeops.c b/fs/xfs/xfs_vnodeops.c index 21da312dd8b..7b967c096d0 100644 --- a/fs/xfs/xfs_vnodeops.c +++ b/fs/xfs/xfs_vnodeops.c @@ -2850,7 +2850,7 @@ xfs_finish_reclaim( int sync_mode) { xfs_perag_t *pag = xfs_get_perag(ip->i_mount, ip->i_ino); - bhv_vnode_t *vp = VFS_I(ip); + struct inode *vp = VFS_I(ip); if (vp && VN_BAD(vp)) goto reclaim; -- GitLab From 41be8bed1f3168f34386f3a15d63682cfd586b8e Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:23:13 +1000 Subject: [PATCH 159/750] [XFS] sanitize xfs_initialize_vnode Sanitize setting up the Linux indode. Setting up the xfs_inode <-> inode link is opencoded in xfs_iget_core now because that's the only place it needs to be done, xfs_initialize_vnode is renamed to xfs_setup_inode and loses all superflous paramaters. The check for I_NEW is removed because it always is true and the di_mode check moves into xfs_iget_core because it's only needed there. xfs_set_inodeops and xfs_revalidate_inode are merged into xfs_setup_inode and the whole things is moved into xfs_iops.c where it belongs. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31782a Signed-off-by: Christoph Hellwig Signed-off-by: Niv Sardi Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_iops.c | 103 ++++++++++++++++++++++++++++++-- fs/xfs/linux-2.6/xfs_iops.h | 8 +-- fs/xfs/linux-2.6/xfs_super.c | 110 ----------------------------------- fs/xfs/linux-2.6/xfs_super.h | 3 - fs/xfs/xfs_iget.c | 9 ++- fs/xfs/xfs_inode.c | 4 +- 6 files changed, 111 insertions(+), 126 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_iops.c b/fs/xfs/linux-2.6/xfs_iops.c index cc0f21af48f..ace56bd3a5f 100644 --- a/fs/xfs/linux-2.6/xfs_iops.c +++ b/fs/xfs/linux-2.6/xfs_iops.c @@ -710,7 +710,7 @@ out_error: return error; } -const struct inode_operations xfs_inode_operations = { +static const struct inode_operations xfs_inode_operations = { .permission = xfs_vn_permission, .truncate = xfs_vn_truncate, .getattr = xfs_vn_getattr, @@ -722,7 +722,7 @@ const struct inode_operations xfs_inode_operations = { .fallocate = xfs_vn_fallocate, }; -const struct inode_operations xfs_dir_inode_operations = { +static const struct inode_operations xfs_dir_inode_operations = { .create = xfs_vn_create, .lookup = xfs_vn_lookup, .link = xfs_vn_link, @@ -747,7 +747,7 @@ const struct inode_operations xfs_dir_inode_operations = { .listxattr = xfs_vn_listxattr, }; -const struct inode_operations xfs_dir_ci_inode_operations = { +static const struct inode_operations xfs_dir_ci_inode_operations = { .create = xfs_vn_create, .lookup = xfs_vn_ci_lookup, .link = xfs_vn_link, @@ -772,7 +772,7 @@ const struct inode_operations xfs_dir_ci_inode_operations = { .listxattr = xfs_vn_listxattr, }; -const struct inode_operations xfs_symlink_inode_operations = { +static const struct inode_operations xfs_symlink_inode_operations = { .readlink = generic_readlink, .follow_link = xfs_vn_follow_link, .put_link = xfs_vn_put_link, @@ -784,3 +784,98 @@ const struct inode_operations xfs_symlink_inode_operations = { .removexattr = generic_removexattr, .listxattr = xfs_vn_listxattr, }; + +STATIC void +xfs_diflags_to_iflags( + struct inode *inode, + struct xfs_inode *ip) +{ + if (ip->i_d.di_flags & XFS_DIFLAG_IMMUTABLE) + inode->i_flags |= S_IMMUTABLE; + else + inode->i_flags &= ~S_IMMUTABLE; + if (ip->i_d.di_flags & XFS_DIFLAG_APPEND) + inode->i_flags |= S_APPEND; + else + inode->i_flags &= ~S_APPEND; + if (ip->i_d.di_flags & XFS_DIFLAG_SYNC) + inode->i_flags |= S_SYNC; + else + inode->i_flags &= ~S_SYNC; + if (ip->i_d.di_flags & XFS_DIFLAG_NOATIME) + inode->i_flags |= S_NOATIME; + else + inode->i_flags &= ~S_NOATIME; +} + +/* + * Initialize the Linux inode, set up the operation vectors and + * unlock the inode. + * + * When reading existing inodes from disk this is called directly + * from xfs_iget, when creating a new inode it is called from + * xfs_ialloc after setting up the inode. + */ +void +xfs_setup_inode( + struct xfs_inode *ip) +{ + struct inode *inode = ip->i_vnode; + + inode->i_mode = ip->i_d.di_mode; + inode->i_nlink = ip->i_d.di_nlink; + inode->i_uid = ip->i_d.di_uid; + inode->i_gid = ip->i_d.di_gid; + + switch (inode->i_mode & S_IFMT) { + case S_IFBLK: + case S_IFCHR: + inode->i_rdev = + MKDEV(sysv_major(ip->i_df.if_u2.if_rdev) & 0x1ff, + sysv_minor(ip->i_df.if_u2.if_rdev)); + break; + default: + inode->i_rdev = 0; + break; + } + + inode->i_generation = ip->i_d.di_gen; + i_size_write(inode, ip->i_d.di_size); + inode->i_atime.tv_sec = ip->i_d.di_atime.t_sec; + inode->i_atime.tv_nsec = ip->i_d.di_atime.t_nsec; + inode->i_mtime.tv_sec = ip->i_d.di_mtime.t_sec; + inode->i_mtime.tv_nsec = ip->i_d.di_mtime.t_nsec; + inode->i_ctime.tv_sec = ip->i_d.di_ctime.t_sec; + inode->i_ctime.tv_nsec = ip->i_d.di_ctime.t_nsec; + xfs_diflags_to_iflags(inode, ip); + xfs_iflags_clear(ip, XFS_IMODIFIED); + + switch (inode->i_mode & S_IFMT) { + case S_IFREG: + inode->i_op = &xfs_inode_operations; + inode->i_fop = &xfs_file_operations; + inode->i_mapping->a_ops = &xfs_address_space_operations; + break; + case S_IFDIR: + if (xfs_sb_version_hasasciici(&XFS_M(inode->i_sb)->m_sb)) + inode->i_op = &xfs_dir_ci_inode_operations; + else + inode->i_op = &xfs_dir_inode_operations; + inode->i_fop = &xfs_dir_file_operations; + break; + case S_IFLNK: + inode->i_op = &xfs_symlink_inode_operations; + if (!(ip->i_df.if_flags & XFS_IFINLINE)) + inode->i_mapping->a_ops = &xfs_address_space_operations; + break; + default: + inode->i_op = &xfs_inode_operations; + init_special_inode(inode, inode->i_mode, inode->i_rdev); + break; + } + + xfs_iflags_clear(ip, XFS_INEW); + barrier(); + + unlock_new_inode(inode); +} diff --git a/fs/xfs/linux-2.6/xfs_iops.h b/fs/xfs/linux-2.6/xfs_iops.h index fdda404bc34..2204f466dee 100644 --- a/fs/xfs/linux-2.6/xfs_iops.h +++ b/fs/xfs/linux-2.6/xfs_iops.h @@ -18,10 +18,7 @@ #ifndef __XFS_IOPS_H__ #define __XFS_IOPS_H__ -extern const struct inode_operations xfs_inode_operations; -extern const struct inode_operations xfs_dir_inode_operations; -extern const struct inode_operations xfs_dir_ci_inode_operations; -extern const struct inode_operations xfs_symlink_inode_operations; +struct xfs_inode; extern const struct file_operations xfs_file_operations; extern const struct file_operations xfs_dir_file_operations; @@ -29,8 +26,9 @@ extern const struct file_operations xfs_invis_file_operations; extern ssize_t xfs_vn_listxattr(struct dentry *, char *data, size_t size); -struct xfs_inode; extern void xfs_ichgtime(struct xfs_inode *, int); extern void xfs_ichgtime_fast(struct xfs_inode *, struct inode *, int); +extern void xfs_setup_inode(struct xfs_inode *); + #endif /* __XFS_IOPS_H__ */ diff --git a/fs/xfs/linux-2.6/xfs_super.c b/fs/xfs/linux-2.6/xfs_super.c index 7605b071dc8..0eaad84a680 100644 --- a/fs/xfs/linux-2.6/xfs_super.c +++ b/fs/xfs/linux-2.6/xfs_super.c @@ -581,116 +581,6 @@ xfs_max_file_offset( return (((__uint64_t)pagefactor) << bitshift) - 1; } -STATIC_INLINE void -xfs_set_inodeops( - struct inode *inode) -{ - switch (inode->i_mode & S_IFMT) { - case S_IFREG: - inode->i_op = &xfs_inode_operations; - inode->i_fop = &xfs_file_operations; - inode->i_mapping->a_ops = &xfs_address_space_operations; - break; - case S_IFDIR: - if (xfs_sb_version_hasasciici(&XFS_M(inode->i_sb)->m_sb)) - inode->i_op = &xfs_dir_ci_inode_operations; - else - inode->i_op = &xfs_dir_inode_operations; - inode->i_fop = &xfs_dir_file_operations; - break; - case S_IFLNK: - inode->i_op = &xfs_symlink_inode_operations; - if (!(XFS_I(inode)->i_df.if_flags & XFS_IFINLINE)) - inode->i_mapping->a_ops = &xfs_address_space_operations; - break; - default: - inode->i_op = &xfs_inode_operations; - init_special_inode(inode, inode->i_mode, inode->i_rdev); - break; - } -} - -STATIC_INLINE void -xfs_revalidate_inode( - xfs_mount_t *mp, - struct inode *inode, - xfs_inode_t *ip) -{ - - inode->i_mode = ip->i_d.di_mode; - inode->i_nlink = ip->i_d.di_nlink; - inode->i_uid = ip->i_d.di_uid; - inode->i_gid = ip->i_d.di_gid; - - switch (inode->i_mode & S_IFMT) { - case S_IFBLK: - case S_IFCHR: - inode->i_rdev = - MKDEV(sysv_major(ip->i_df.if_u2.if_rdev) & 0x1ff, - sysv_minor(ip->i_df.if_u2.if_rdev)); - break; - default: - inode->i_rdev = 0; - break; - } - - inode->i_generation = ip->i_d.di_gen; - i_size_write(inode, ip->i_d.di_size); - inode->i_atime.tv_sec = ip->i_d.di_atime.t_sec; - inode->i_atime.tv_nsec = ip->i_d.di_atime.t_nsec; - inode->i_mtime.tv_sec = ip->i_d.di_mtime.t_sec; - inode->i_mtime.tv_nsec = ip->i_d.di_mtime.t_nsec; - inode->i_ctime.tv_sec = ip->i_d.di_ctime.t_sec; - inode->i_ctime.tv_nsec = ip->i_d.di_ctime.t_nsec; - if (ip->i_d.di_flags & XFS_DIFLAG_IMMUTABLE) - inode->i_flags |= S_IMMUTABLE; - else - inode->i_flags &= ~S_IMMUTABLE; - if (ip->i_d.di_flags & XFS_DIFLAG_APPEND) - inode->i_flags |= S_APPEND; - else - inode->i_flags &= ~S_APPEND; - if (ip->i_d.di_flags & XFS_DIFLAG_SYNC) - inode->i_flags |= S_SYNC; - else - inode->i_flags &= ~S_SYNC; - if (ip->i_d.di_flags & XFS_DIFLAG_NOATIME) - inode->i_flags |= S_NOATIME; - else - inode->i_flags &= ~S_NOATIME; - xfs_iflags_clear(ip, XFS_IMODIFIED); -} - -void -xfs_initialize_vnode( - struct xfs_mount *mp, - struct inode *inode, - struct xfs_inode *ip) -{ - - if (!ip->i_vnode) { - ip->i_vnode = inode; - inode->i_private = ip; - } - - /* - * We need to set the ops vectors, and unlock the inode, but if - * we have been called during the new inode create process, it is - * too early to fill in the Linux inode. We will get called a - * second time once the inode is properly set up, and then we can - * finish our work. - */ - if (ip->i_d.di_mode != 0 && (inode->i_state & I_NEW)) { - xfs_revalidate_inode(mp, inode, ip); - xfs_set_inodeops(inode); - - xfs_iflags_clear(ip, XFS_INEW); - barrier(); - - unlock_new_inode(inode); - } -} - int xfs_blkdev_get( xfs_mount_t *mp, diff --git a/fs/xfs/linux-2.6/xfs_super.h b/fs/xfs/linux-2.6/xfs_super.h index 57145fff385..fe2ef4e6a0f 100644 --- a/fs/xfs/linux-2.6/xfs_super.h +++ b/fs/xfs/linux-2.6/xfs_super.h @@ -101,9 +101,6 @@ struct block_device; extern __uint64_t xfs_max_file_offset(unsigned int); -extern void xfs_initialize_vnode(struct xfs_mount *mp, struct inode *vp, - struct xfs_inode *ip); - extern void xfs_flush_inode(struct xfs_inode *); extern void xfs_flush_device(struct xfs_inode *); diff --git a/fs/xfs/xfs_iget.c b/fs/xfs/xfs_iget.c index d44342640ca..539c2dd8eae 100644 --- a/fs/xfs/xfs_iget.c +++ b/fs/xfs/xfs_iget.c @@ -287,11 +287,18 @@ finish_inode: xfs_iflags_set(ip, XFS_IMODIFIED); *ipp = ip; + /* + * Set up the Linux with the Linux inode. + */ + ip->i_vnode = inode; + inode->i_private = ip; + /* * If we have a real type for an on-disk inode, we can set ops(&unlock) * now. If it's a new inode being created, xfs_ialloc will handle it. */ - xfs_initialize_vnode(mp, inode, ip); + if (ip->i_d.di_mode != 0) + xfs_setup_inode(ip); return 0; } diff --git a/fs/xfs/xfs_inode.c b/fs/xfs/xfs_inode.c index 19e7a7b8270..5bb638b445e 100644 --- a/fs/xfs/xfs_inode.c +++ b/fs/xfs/xfs_inode.c @@ -1046,7 +1046,6 @@ xfs_ialloc( { xfs_ino_t ino; xfs_inode_t *ip; - struct inode *vp; uint flags; int error; @@ -1077,7 +1076,6 @@ xfs_ialloc( } ASSERT(ip != NULL); - vp = VFS_I(ip); ip->i_d.di_mode = (__uint16_t)mode; ip->i_d.di_onlink = 0; ip->i_d.di_nlink = nlink; @@ -1220,7 +1218,7 @@ xfs_ialloc( xfs_trans_log_inode(tp, ip, flags); /* now that we have an i_mode we can setup inode ops and unlock */ - xfs_initialize_vnode(tp->t_mountp, vp, ip); + xfs_setup_inode(ip); *ipp = ip; return 0; -- GitLab From cdcf43335cbb2380e533441e007e0c4ec42634d5 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:23:50 +1000 Subject: [PATCH 160/750] [XFS] small cleanups in xfs_btree.c Remove unneeded xfs_btree_get_block forward declaration. Move xfs_btree_firstrec next to xfs_btree_lastrec. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31787a Signed-off-by: Christoph Hellwig Signed-off-by: Tim Shimmin Signed-off-by: David Chinner Signed-off-by: Lachlan McIlroy --- fs/xfs/xfs_btree.c | 87 ++++++++++++++++------------------------------ 1 file changed, 30 insertions(+), 57 deletions(-) diff --git a/fs/xfs/xfs_btree.c b/fs/xfs/xfs_btree.c index aeb87ca69fc..2b0d454e92e 100644 --- a/fs/xfs/xfs_btree.c +++ b/fs/xfs/xfs_btree.c @@ -46,37 +46,10 @@ kmem_zone_t *xfs_btree_cur_zone; /* * Btree magic numbers. */ -const __uint32_t xfs_magics[XFS_BTNUM_MAX] = -{ +const __uint32_t xfs_magics[XFS_BTNUM_MAX] = { XFS_ABTB_MAGIC, XFS_ABTC_MAGIC, XFS_BMAP_MAGIC, XFS_IBT_MAGIC }; -/* - * Prototypes for internal routines. - */ - -/* - * Checking routine: return maxrecs for the block. - */ -STATIC int /* number of records fitting in block */ -xfs_btree_maxrecs( - xfs_btree_cur_t *cur, /* btree cursor */ - xfs_btree_block_t *block);/* generic btree block pointer */ - -/* - * Internal routines. - */ - -/* - * Retrieve the block pointer from the cursor at the given level. - * This may be a bmap btree root or from a buffer. - */ -STATIC xfs_btree_block_t * /* generic btree block pointer */ -xfs_btree_get_block( - xfs_btree_cur_t *cur, /* btree cursor */ - int level, /* level in btree */ - struct xfs_buf **bpp); /* buffer containing the block */ - /* * Checking routine: return maxrecs for the block. */ @@ -456,35 +429,6 @@ xfs_btree_dup_cursor( return 0; } -/* - * Change the cursor to point to the first record at the given level. - * Other levels are unaffected. - */ -int /* success=1, failure=0 */ -xfs_btree_firstrec( - xfs_btree_cur_t *cur, /* btree cursor */ - int level) /* level to change */ -{ - xfs_btree_block_t *block; /* generic btree block pointer */ - xfs_buf_t *bp; /* buffer containing block */ - - /* - * Get the block pointer for this level. - */ - block = xfs_btree_get_block(cur, level, &bp); - xfs_btree_check_block(cur, block, level, bp); - /* - * It's empty, there is no such record. - */ - if (!block->bb_h.bb_numrecs) - return 0; - /* - * Set the ptr value to 1, that's the first record/key. - */ - cur->bc_ptrs[level] = 1; - return 1; -} - /* * Retrieve the block pointer from the cursor at the given level. * This may be a bmap btree root or from a buffer. @@ -670,6 +614,35 @@ xfs_btree_islastblock( return be32_to_cpu(block->bb_u.s.bb_rightsib) == NULLAGBLOCK; } +/* + * Change the cursor to point to the first record at the given level. + * Other levels are unaffected. + */ +int /* success=1, failure=0 */ +xfs_btree_firstrec( + xfs_btree_cur_t *cur, /* btree cursor */ + int level) /* level to change */ +{ + xfs_btree_block_t *block; /* generic btree block pointer */ + xfs_buf_t *bp; /* buffer containing block */ + + /* + * Get the block pointer for this level. + */ + block = xfs_btree_get_block(cur, level, &bp); + xfs_btree_check_block(cur, block, level, bp); + /* + * It's empty, there is no such record. + */ + if (!block->bb_h.bb_numrecs) + return 0; + /* + * Set the ptr value to 1, that's the first record/key. + */ + cur->bc_ptrs[level] = 1; + return 1; +} + /* * Change the cursor to point to the last record in the current block * at the given level. Other levels are unaffected. -- GitLab From 169d6227a71da125913c69c381643a8ae89da62d Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:25:27 +1000 Subject: [PATCH 161/750] [XFS] Use the same btree_cur union member for alloc and inobt trees. The alloc and inobt btree use the same agbp/agno pair in the btree_cur union. Make them use the same bc_private.a union member so that code for these two short form btree implementations can be shared. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31788a Signed-off-by: Christoph Hellwig Signed-off-by: Tim Shimmin Signed-off-by: David Chinner Signed-off-by: Lachlan McIlroy --- fs/xfs/xfs_btree.c | 18 +++++++++--------- fs/xfs/xfs_btree.h | 8 ++------ fs/xfs/xfs_ialloc_btree.c | 30 +++++++++++++++--------------- 3 files changed, 26 insertions(+), 30 deletions(-) diff --git a/fs/xfs/xfs_btree.c b/fs/xfs/xfs_btree.c index 2b0d454e92e..cc593a84c34 100644 --- a/fs/xfs/xfs_btree.c +++ b/fs/xfs/xfs_btree.c @@ -570,6 +570,13 @@ xfs_btree_init_cursor( cur->bc_private.a.agbp = agbp; cur->bc_private.a.agno = agno; break; + case XFS_BTNUM_INO: + /* + * Inode allocation btree fields. + */ + cur->bc_private.a.agbp = agbp; + cur->bc_private.a.agno = agno; + break; case XFS_BTNUM_BMAP: /* * Bmap btree fields. @@ -582,13 +589,6 @@ xfs_btree_init_cursor( cur->bc_private.b.flags = 0; cur->bc_private.b.whichfork = whichfork; break; - case XFS_BTNUM_INO: - /* - * Inode allocation btree fields. - */ - cur->bc_private.i.agbp = agbp; - cur->bc_private.i.agno = agno; - break; default: ASSERT(0); } @@ -863,12 +863,12 @@ xfs_btree_readahead_core( case XFS_BTNUM_INO: i = XFS_BUF_TO_INOBT_BLOCK(cur->bc_bufs[lev]); if ((lr & XFS_BTCUR_LEFTRA) && be32_to_cpu(i->bb_leftsib) != NULLAGBLOCK) { - xfs_btree_reada_bufs(cur->bc_mp, cur->bc_private.i.agno, + xfs_btree_reada_bufs(cur->bc_mp, cur->bc_private.a.agno, be32_to_cpu(i->bb_leftsib), 1); rval++; } if ((lr & XFS_BTCUR_RIGHTRA) && be32_to_cpu(i->bb_rightsib) != NULLAGBLOCK) { - xfs_btree_reada_bufs(cur->bc_mp, cur->bc_private.i.agno, + xfs_btree_reada_bufs(cur->bc_mp, cur->bc_private.a.agno, be32_to_cpu(i->bb_rightsib), 1); rval++; } diff --git a/fs/xfs/xfs_btree.h b/fs/xfs/xfs_btree.h index 7440b78f9ce..1f528a2a375 100644 --- a/fs/xfs/xfs_btree.h +++ b/fs/xfs/xfs_btree.h @@ -158,8 +158,8 @@ typedef struct xfs_btree_cur __uint8_t bc_blocklog; /* log2(blocksize) of btree blocks */ xfs_btnum_t bc_btnum; /* identifies which btree type */ union { - struct { /* needed for BNO, CNT */ - struct xfs_buf *agbp; /* agf buffer pointer */ + struct { /* needed for BNO, CNT, INO */ + struct xfs_buf *agbp; /* agf/agi buffer pointer */ xfs_agnumber_t agno; /* ag number */ } a; struct { /* needed for BMAP */ @@ -172,10 +172,6 @@ typedef struct xfs_btree_cur char flags; /* flags */ #define XFS_BTCUR_BPRV_WASDEL 1 /* was delayed */ } b; - struct { /* needed for INO */ - struct xfs_buf *agbp; /* agi buffer pointer */ - xfs_agnumber_t agno; /* ag number */ - } i; } bc_private; /* per-btree type data */ } xfs_btree_cur_t; diff --git a/fs/xfs/xfs_ialloc_btree.c b/fs/xfs/xfs_ialloc_btree.c index e5310c90e50..83502f3edef 100644 --- a/fs/xfs/xfs_ialloc_btree.c +++ b/fs/xfs/xfs_ialloc_btree.c @@ -181,7 +181,7 @@ xfs_inobt_delrec( * then we can get rid of this level. */ if (numrecs == 1 && level > 0) { - agbp = cur->bc_private.i.agbp; + agbp = cur->bc_private.a.agbp; agi = XFS_BUF_TO_AGI(agbp); /* * pp is still set to the first pointer in the block. @@ -194,7 +194,7 @@ xfs_inobt_delrec( * Free the block. */ if ((error = xfs_free_extent(cur->bc_tp, - XFS_AGB_TO_FSB(mp, cur->bc_private.i.agno, bno), 1))) + XFS_AGB_TO_FSB(mp, cur->bc_private.a.agno, bno), 1))) return error; xfs_trans_binval(cur->bc_tp, bp); xfs_ialloc_log_agi(cur->bc_tp, agbp, @@ -379,7 +379,7 @@ xfs_inobt_delrec( rrecs = be16_to_cpu(right->bb_numrecs); rbp = bp; if ((error = xfs_btree_read_bufs(mp, cur->bc_tp, - cur->bc_private.i.agno, lbno, 0, &lbp, + cur->bc_private.a.agno, lbno, 0, &lbp, XFS_INO_BTREE_REF))) return error; left = XFS_BUF_TO_INOBT_BLOCK(lbp); @@ -401,7 +401,7 @@ xfs_inobt_delrec( lrecs = be16_to_cpu(left->bb_numrecs); lbp = bp; if ((error = xfs_btree_read_bufs(mp, cur->bc_tp, - cur->bc_private.i.agno, rbno, 0, &rbp, + cur->bc_private.a.agno, rbno, 0, &rbp, XFS_INO_BTREE_REF))) return error; right = XFS_BUF_TO_INOBT_BLOCK(rbp); @@ -484,7 +484,7 @@ xfs_inobt_delrec( xfs_buf_t *rrbp; if ((error = xfs_btree_read_bufs(mp, cur->bc_tp, - cur->bc_private.i.agno, be32_to_cpu(left->bb_rightsib), 0, + cur->bc_private.a.agno, be32_to_cpu(left->bb_rightsib), 0, &rrbp, XFS_INO_BTREE_REF))) return error; rrblock = XFS_BUF_TO_INOBT_BLOCK(rrbp); @@ -497,7 +497,7 @@ xfs_inobt_delrec( * Free the deleting block. */ if ((error = xfs_free_extent(cur->bc_tp, XFS_AGB_TO_FSB(mp, - cur->bc_private.i.agno, rbno), 1))) + cur->bc_private.a.agno, rbno), 1))) return error; xfs_trans_binval(cur->bc_tp, rbp); /* @@ -854,7 +854,7 @@ xfs_inobt_lookup( { xfs_agi_t *agi; /* a.g. inode header */ - agi = XFS_BUF_TO_AGI(cur->bc_private.i.agbp); + agi = XFS_BUF_TO_AGI(cur->bc_private.a.agbp); agno = be32_to_cpu(agi->agi_seqno); agbno = be32_to_cpu(agi->agi_root); } @@ -1089,7 +1089,7 @@ xfs_inobt_lshift( * Set up the left neighbor as "left". */ if ((error = xfs_btree_read_bufs(cur->bc_mp, cur->bc_tp, - cur->bc_private.i.agno, be32_to_cpu(right->bb_leftsib), + cur->bc_private.a.agno, be32_to_cpu(right->bb_leftsib), 0, &lbp, XFS_INO_BTREE_REF))) return error; left = XFS_BUF_TO_INOBT_BLOCK(lbp); @@ -1207,10 +1207,10 @@ xfs_inobt_newroot( /* * Get a block & a buffer. */ - agi = XFS_BUF_TO_AGI(cur->bc_private.i.agbp); + agi = XFS_BUF_TO_AGI(cur->bc_private.a.agbp); args.tp = cur->bc_tp; args.mp = cur->bc_mp; - args.fsbno = XFS_AGB_TO_FSB(args.mp, cur->bc_private.i.agno, + args.fsbno = XFS_AGB_TO_FSB(args.mp, cur->bc_private.a.agno, be32_to_cpu(agi->agi_root)); args.mod = args.minleft = args.alignment = args.total = args.wasdel = args.isfl = args.userdata = args.minalignslop = 0; @@ -1233,7 +1233,7 @@ xfs_inobt_newroot( */ agi->agi_root = cpu_to_be32(args.agbno); be32_add_cpu(&agi->agi_level, 1); - xfs_ialloc_log_agi(args.tp, cur->bc_private.i.agbp, + xfs_ialloc_log_agi(args.tp, cur->bc_private.a.agbp, XFS_AGI_ROOT | XFS_AGI_LEVEL); /* * At the previous root level there are now two blocks: the old @@ -1376,7 +1376,7 @@ xfs_inobt_rshift( * Set up the right neighbor as "right". */ if ((error = xfs_btree_read_bufs(cur->bc_mp, cur->bc_tp, - cur->bc_private.i.agno, be32_to_cpu(left->bb_rightsib), + cur->bc_private.a.agno, be32_to_cpu(left->bb_rightsib), 0, &rbp, XFS_INO_BTREE_REF))) return error; right = XFS_BUF_TO_INOBT_BLOCK(rbp); @@ -1492,7 +1492,7 @@ xfs_inobt_split( * Allocate the new block. * If we can't do it, we're toast. Give up. */ - args.fsbno = XFS_AGB_TO_FSB(args.mp, cur->bc_private.i.agno, lbno); + args.fsbno = XFS_AGB_TO_FSB(args.mp, cur->bc_private.a.agno, lbno); args.mod = args.minleft = args.alignment = args.total = args.wasdel = args.isfl = args.userdata = args.minalignslop = 0; args.minlen = args.maxlen = args.prod = 1; @@ -1725,7 +1725,7 @@ xfs_inobt_decrement( agbno = be32_to_cpu(*XFS_INOBT_PTR_ADDR(block, cur->bc_ptrs[lev], cur)); if ((error = xfs_btree_read_bufs(cur->bc_mp, cur->bc_tp, - cur->bc_private.i.agno, agbno, 0, &bp, + cur->bc_private.a.agno, agbno, 0, &bp, XFS_INO_BTREE_REF))) return error; lev--; @@ -1897,7 +1897,7 @@ xfs_inobt_increment( agbno = be32_to_cpu(*XFS_INOBT_PTR_ADDR(block, cur->bc_ptrs[lev], cur)); if ((error = xfs_btree_read_bufs(cur->bc_mp, cur->bc_tp, - cur->bc_private.i.agno, agbno, 0, &bp, + cur->bc_private.a.agno, agbno, 0, &bp, XFS_INO_BTREE_REF))) return error; lev--; -- GitLab From d63f154a36c4ec7c2826874371887cecae375ebb Mon Sep 17 00:00:00 2001 From: Lachlan McIlroy Date: Wed, 13 Aug 2008 16:28:40 +1000 Subject: [PATCH 162/750] [XFS] Fix compile failure in xfs_buf_trace() SGI-PV: 957103 SGI-Modid: xfs-linux-melb:xfs-kern:31804a Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_buf.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/xfs/linux-2.6/xfs_buf.c b/fs/xfs/linux-2.6/xfs_buf.c index 9f45c74f1a8..a01daa7b592 100644 --- a/fs/xfs/linux-2.6/xfs_buf.c +++ b/fs/xfs/linux-2.6/xfs_buf.c @@ -58,7 +58,7 @@ xfs_buf_trace( bp, id, (void *)(unsigned long)bp->b_flags, (void *)(unsigned long)bp->b_hold.counter, - (void *)(unsigned long)bp->b_sema.count.counter, + (void *)(unsigned long)bp->b_sema.count, (void *)current, data, ra, (void *)(unsigned long)((bp->b_file_offset>>32) & 0xffffffff), -- GitLab From 597bca6378e0273a5d16346c941cab1ec2e0116d Mon Sep 17 00:00:00 2001 From: Harvey Harrison Date: Wed, 13 Aug 2008 16:29:21 +1000 Subject: [PATCH 163/750] [XFS] use get_unaligned_* helpers SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31813a Signed-off-by: Harvey Harrison Signed-off-by: Lachlan McIlroy --- fs/xfs/xfs_inode.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/fs/xfs/xfs_inode.c b/fs/xfs/xfs_inode.c index 5bb638b445e..b8444ee4dc9 100644 --- a/fs/xfs/xfs_inode.c +++ b/fs/xfs/xfs_inode.c @@ -580,8 +580,8 @@ xfs_iformat_extents( xfs_validate_extents(ifp, nex, XFS_EXTFMT_INODE(ip)); for (i = 0; i < nex; i++, dp++) { xfs_bmbt_rec_host_t *ep = xfs_iext_get_ext(ifp, i); - ep->l0 = be64_to_cpu(get_unaligned(&dp->l0)); - ep->l1 = be64_to_cpu(get_unaligned(&dp->l1)); + ep->l0 = get_unaligned_be64(&dp->l0); + ep->l1 = get_unaligned_be64(&dp->l1); } XFS_BMAP_TRACE_EXLIST(ip, nex, whichfork); if (whichfork != XFS_DATA_FORK || -- GitLab From 12017faf387437c01ff63bbe46b629550b15bd70 Mon Sep 17 00:00:00 2001 From: David Chinner Date: Wed, 13 Aug 2008 16:34:31 +1000 Subject: [PATCH 164/750] [XFS] clean up stale references to semaphores A lot of code has been converted away from semaphores, but there are still comments that reference semaphore behaviour. The log code is the worst offender. Update the comments to reflect what the code really does now. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31814a Signed-off-by: David Chinner Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_vnode.c | 2 +- fs/xfs/xfs_log.c | 67 +++++++++++++++++------------------- fs/xfs/xfs_log_priv.h | 12 +++---- 3 files changed, 39 insertions(+), 42 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_vnode.c b/fs/xfs/linux-2.6/xfs_vnode.c index 5cad3274db0..b52528bbbff 100644 --- a/fs/xfs/linux-2.6/xfs_vnode.c +++ b/fs/xfs/linux-2.6/xfs_vnode.c @@ -33,7 +33,7 @@ /* - * Dedicated vnode inactive/reclaim sync semaphores. + * Dedicated vnode inactive/reclaim sync wait queues. * Prime number of hash buckets since address is used as the key. */ #define NVSYNC 37 diff --git a/fs/xfs/xfs_log.c b/fs/xfs/xfs_log.c index 91b00a5686c..0816c5d6d76 100644 --- a/fs/xfs/xfs_log.c +++ b/fs/xfs/xfs_log.c @@ -357,11 +357,11 @@ xfs_log_done(xfs_mount_t *mp, * Asynchronous forces are implemented by setting the WANT_SYNC * bit in the appropriate in-core log and then returning. * - * Synchronous forces are implemented with a semaphore. All callers - * to force a given lsn to disk will wait on a semaphore attached to the + * Synchronous forces are implemented with a signal variable. All callers + * to force a given lsn to disk will wait on a the sv attached to the * specific in-core log. When given in-core log finally completes its * write to disk, that thread will wake up all threads waiting on the - * semaphore. + * sv. */ int _xfs_log_force( @@ -707,7 +707,7 @@ xfs_log_unmount_write(xfs_mount_t *mp) if (!(iclog->ic_state == XLOG_STATE_ACTIVE || iclog->ic_state == XLOG_STATE_DIRTY)) { if (!XLOG_FORCED_SHUTDOWN(log)) { - sv_wait(&iclog->ic_forcesema, PMEM, + sv_wait(&iclog->ic_force_wait, PMEM, &log->l_icloglock, s); } else { spin_unlock(&log->l_icloglock); @@ -748,7 +748,7 @@ xfs_log_unmount_write(xfs_mount_t *mp) || iclog->ic_state == XLOG_STATE_DIRTY || iclog->ic_state == XLOG_STATE_IOERROR) ) { - sv_wait(&iclog->ic_forcesema, PMEM, + sv_wait(&iclog->ic_force_wait, PMEM, &log->l_icloglock, s); } else { spin_unlock(&log->l_icloglock); @@ -838,7 +838,7 @@ xfs_log_move_tail(xfs_mount_t *mp, break; tail_lsn = 0; free_bytes -= tic->t_unit_res; - sv_signal(&tic->t_sema); + sv_signal(&tic->t_wait); tic = tic->t_next; } while (tic != log->l_write_headq); } @@ -859,7 +859,7 @@ xfs_log_move_tail(xfs_mount_t *mp, break; tail_lsn = 0; free_bytes -= need_bytes; - sv_signal(&tic->t_sema); + sv_signal(&tic->t_wait); tic = tic->t_next; } while (tic != log->l_reserve_headq); } @@ -1285,8 +1285,8 @@ xlog_alloc_log(xfs_mount_t *mp, ASSERT(XFS_BUF_ISBUSY(iclog->ic_bp)); ASSERT(XFS_BUF_VALUSEMA(iclog->ic_bp) <= 0); - sv_init(&iclog->ic_forcesema, SV_DEFAULT, "iclog-force"); - sv_init(&iclog->ic_writesema, SV_DEFAULT, "iclog-write"); + sv_init(&iclog->ic_force_wait, SV_DEFAULT, "iclog-force"); + sv_init(&iclog->ic_write_wait, SV_DEFAULT, "iclog-write"); iclogp = &iclog->ic_next; } @@ -1565,8 +1565,8 @@ xlog_dealloc_log(xlog_t *log) iclog = log->l_iclog; for (i=0; il_iclog_bufs; i++) { - sv_destroy(&iclog->ic_forcesema); - sv_destroy(&iclog->ic_writesema); + sv_destroy(&iclog->ic_force_wait); + sv_destroy(&iclog->ic_write_wait); xfs_buf_free(iclog->ic_bp); #ifdef XFS_LOG_TRACE if (iclog->ic_trace != NULL) { @@ -1976,7 +1976,7 @@ xlog_write(xfs_mount_t * mp, /* Clean iclogs starting from the head. This ordering must be * maintained, so an iclog doesn't become ACTIVE beyond one that * is SYNCING. This is also required to maintain the notion that we use - * a counting semaphore to hold off would be writers to the log when every + * a ordered wait queue to hold off would be writers to the log when every * iclog is trying to sync to disk. * * State Change: DIRTY -> ACTIVE @@ -2240,7 +2240,7 @@ xlog_state_do_callback( xlog_state_clean_log(log); /* wake up threads waiting in xfs_log_force() */ - sv_broadcast(&iclog->ic_forcesema); + sv_broadcast(&iclog->ic_force_wait); iclog = iclog->ic_next; } while (first_iclog != iclog); @@ -2302,8 +2302,7 @@ xlog_state_do_callback( * the second completion goes through. * * Callbacks could take time, so they are done outside the scope of the - * global state machine log lock. Assume that the calls to cvsema won't - * take a long time. At least we know it won't sleep. + * global state machine log lock. */ STATIC void xlog_state_done_syncing( @@ -2339,7 +2338,7 @@ xlog_state_done_syncing( * iclog buffer, we wake them all, one will get to do the * I/O, the others get to wait for the result. */ - sv_broadcast(&iclog->ic_writesema); + sv_broadcast(&iclog->ic_write_wait); spin_unlock(&log->l_icloglock); xlog_state_do_callback(log, aborted, iclog); /* also cleans log */ } /* xlog_state_done_syncing */ @@ -2347,11 +2346,9 @@ xlog_state_done_syncing( /* * If the head of the in-core log ring is not (ACTIVE or DIRTY), then we must - * sleep. The flush semaphore is set to the number of in-core buffers and - * decremented around disk syncing. Therefore, if all buffers are syncing, - * this semaphore will cause new writes to sleep until a sync completes. - * Otherwise, this code just does p() followed by v(). This approximates - * a sleep/wakeup except we can't race. + * sleep. We wait on the flush queue on the head iclog as that should be + * the first iclog to complete flushing. Hence if all iclogs are syncing, + * we will wait here and all new writes will sleep until a sync completes. * * The in-core logs are used in a circular fashion. They are not used * out-of-order even when an iclog past the head is free. @@ -2508,7 +2505,7 @@ xlog_grant_log_space(xlog_t *log, goto error_return; XFS_STATS_INC(xs_sleep_logspace); - sv_wait(&tic->t_sema, PINOD|PLTWAIT, &log->l_grant_lock, s); + sv_wait(&tic->t_wait, PINOD|PLTWAIT, &log->l_grant_lock, s); /* * If we got an error, and the filesystem is shutting down, * we'll catch it down below. So just continue... @@ -2534,7 +2531,7 @@ redo: xlog_trace_loggrant(log, tic, "xlog_grant_log_space: sleep 2"); XFS_STATS_INC(xs_sleep_logspace); - sv_wait(&tic->t_sema, PINOD|PLTWAIT, &log->l_grant_lock, s); + sv_wait(&tic->t_wait, PINOD|PLTWAIT, &log->l_grant_lock, s); if (XLOG_FORCED_SHUTDOWN(log)) { spin_lock(&log->l_grant_lock); @@ -2633,7 +2630,7 @@ xlog_regrant_write_log_space(xlog_t *log, if (free_bytes < ntic->t_unit_res) break; free_bytes -= ntic->t_unit_res; - sv_signal(&ntic->t_sema); + sv_signal(&ntic->t_wait); ntic = ntic->t_next; } while (ntic != log->l_write_headq); @@ -2644,7 +2641,7 @@ xlog_regrant_write_log_space(xlog_t *log, xlog_trace_loggrant(log, tic, "xlog_regrant_write_log_space: sleep 1"); XFS_STATS_INC(xs_sleep_logspace); - sv_wait(&tic->t_sema, PINOD|PLTWAIT, + sv_wait(&tic->t_wait, PINOD|PLTWAIT, &log->l_grant_lock, s); /* If we're shutting down, this tic is already @@ -2673,7 +2670,7 @@ redo: if ((tic->t_flags & XLOG_TIC_IN_Q) == 0) xlog_ins_ticketq(&log->l_write_headq, tic); XFS_STATS_INC(xs_sleep_logspace); - sv_wait(&tic->t_sema, PINOD|PLTWAIT, &log->l_grant_lock, s); + sv_wait(&tic->t_wait, PINOD|PLTWAIT, &log->l_grant_lock, s); /* If we're shutting down, this tic is already off the queue */ if (XLOG_FORCED_SHUTDOWN(log)) { @@ -2916,7 +2913,7 @@ xlog_state_switch_iclogs(xlog_t *log, * 2. the current iclog is drity, and the previous iclog is in the * active or dirty state. * - * We may sleep (call psema) if: + * We may sleep if: * * 1. the current iclog is not in the active nor dirty state. * 2. the current iclog dirty, and the previous iclog is not in the @@ -3013,7 +3010,7 @@ maybe_sleep: return XFS_ERROR(EIO); } XFS_STATS_INC(xs_log_force_sleep); - sv_wait(&iclog->ic_forcesema, PINOD, &log->l_icloglock, s); + sv_wait(&iclog->ic_force_wait, PINOD, &log->l_icloglock, s); /* * No need to grab the log lock here since we're * only deciding whether or not to return EIO @@ -3096,7 +3093,7 @@ try_again: XLOG_STATE_SYNCING))) { ASSERT(!(iclog->ic_state & XLOG_STATE_IOERROR)); XFS_STATS_INC(xs_log_force_sleep); - sv_wait(&iclog->ic_prev->ic_writesema, PSWP, + sv_wait(&iclog->ic_prev->ic_write_wait, PSWP, &log->l_icloglock, s); *log_flushed = 1; already_slept = 1; @@ -3116,7 +3113,7 @@ try_again: !(iclog->ic_state & (XLOG_STATE_ACTIVE | XLOG_STATE_DIRTY))) { /* - * Don't wait on the forcesema if we know that we've + * Don't wait on completion if we know that we've * gotten a log write error. */ if (iclog->ic_state & XLOG_STATE_IOERROR) { @@ -3124,7 +3121,7 @@ try_again: return XFS_ERROR(EIO); } XFS_STATS_INC(xs_log_force_sleep); - sv_wait(&iclog->ic_forcesema, PSWP, &log->l_icloglock, s); + sv_wait(&iclog->ic_force_wait, PSWP, &log->l_icloglock, s); /* * No need to grab the log lock here since we're * only deciding whether or not to return EIO @@ -3180,7 +3177,7 @@ STATIC void xlog_ticket_put(xlog_t *log, xlog_ticket_t *ticket) { - sv_destroy(&ticket->t_sema); + sv_destroy(&ticket->t_wait); kmem_zone_free(xfs_log_ticket_zone, ticket); } /* xlog_ticket_put */ @@ -3270,7 +3267,7 @@ xlog_ticket_get(xlog_t *log, tic->t_trans_type = 0; if (xflags & XFS_LOG_PERM_RESERV) tic->t_flags |= XLOG_TIC_PERM_RESERV; - sv_init(&(tic->t_sema), SV_DEFAULT, "logtick"); + sv_init(&(tic->t_wait), SV_DEFAULT, "logtick"); xlog_tic_reset_res(tic); @@ -3557,14 +3554,14 @@ xfs_log_force_umount( */ if ((tic = log->l_reserve_headq)) { do { - sv_signal(&tic->t_sema); + sv_signal(&tic->t_wait); tic = tic->t_next; } while (tic != log->l_reserve_headq); } if ((tic = log->l_write_headq)) { do { - sv_signal(&tic->t_sema); + sv_signal(&tic->t_wait); tic = tic->t_next; } while (tic != log->l_write_headq); } diff --git a/fs/xfs/xfs_log_priv.h b/fs/xfs/xfs_log_priv.h index 6245913196b..7dcf11e0b2f 100644 --- a/fs/xfs/xfs_log_priv.h +++ b/fs/xfs/xfs_log_priv.h @@ -241,7 +241,7 @@ typedef struct xlog_res { } xlog_res_t; typedef struct xlog_ticket { - sv_t t_sema; /* sleep on this semaphore : 20 */ + sv_t t_wait; /* ticket wait queue : 20 */ struct xlog_ticket *t_next; /* :4|8 */ struct xlog_ticket *t_prev; /* :4|8 */ xlog_tid_t t_tid; /* transaction identifier : 4 */ @@ -314,7 +314,7 @@ typedef struct xlog_rec_ext_header { * xlog_rec_header_t into the reserved space. * - ic_data follows, so a write to disk can start at the beginning of * the iclog. - * - ic_forcesema is used to implement synchronous forcing of the iclog to disk. + * - ic_forcewait is used to implement synchronous forcing of the iclog to disk. * - ic_next is the pointer to the next iclog in the ring. * - ic_bp is a pointer to the buffer used to write this incore log to disk. * - ic_log is a pointer back to the global log structure. @@ -339,8 +339,8 @@ typedef struct xlog_rec_ext_header { * and move everything else out to subsequent cachelines. */ typedef struct xlog_iclog_fields { - sv_t ic_forcesema; - sv_t ic_writesema; + sv_t ic_force_wait; + sv_t ic_write_wait; struct xlog_in_core *ic_next; struct xlog_in_core *ic_prev; struct xfs_buf *ic_bp; @@ -377,8 +377,8 @@ typedef struct xlog_in_core { /* * Defines to save our code from this glop. */ -#define ic_forcesema hic_fields.ic_forcesema -#define ic_writesema hic_fields.ic_writesema +#define ic_force_wait hic_fields.ic_force_wait +#define ic_write_wait hic_fields.ic_write_wait #define ic_next hic_fields.ic_next #define ic_prev hic_fields.ic_prev #define ic_bp hic_fields.ic_bp -- GitLab From b4dd330b9e0c9c78ebff754e72563b148f05e9e0 Mon Sep 17 00:00:00 2001 From: David Chinner Date: Wed, 13 Aug 2008 16:36:11 +1000 Subject: [PATCH 165/750] [XFS] replace the XFS buf iodone semaphore with a completion The xfs_buf_t b_iodonesema is really just a semaphore that wants to be a completion. Change it to a completion and remove the last user of the sema_t from XFS. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31815a Signed-off-by: David Chinner Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_buf.c | 6 +++--- fs/xfs/linux-2.6/xfs_buf.h | 4 ++-- fs/xfs/xfs_buf_item.c | 2 +- fs/xfs/xfs_rw.c | 2 +- 4 files changed, 7 insertions(+), 7 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_buf.c b/fs/xfs/linux-2.6/xfs_buf.c index a01daa7b592..a0072d9315a 100644 --- a/fs/xfs/linux-2.6/xfs_buf.c +++ b/fs/xfs/linux-2.6/xfs_buf.c @@ -253,7 +253,7 @@ _xfs_buf_initialize( memset(bp, 0, sizeof(xfs_buf_t)); atomic_set(&bp->b_hold, 1); - init_MUTEX_LOCKED(&bp->b_iodonesema); + init_completion(&bp->b_iowait); INIT_LIST_HEAD(&bp->b_list); INIT_LIST_HEAD(&bp->b_hash_list); init_MUTEX_LOCKED(&bp->b_sema); /* held, no waiters */ @@ -1033,7 +1033,7 @@ xfs_buf_ioend( xfs_buf_iodone_work(&bp->b_iodone_work); } } else { - up(&bp->b_iodonesema); + complete(&bp->b_iowait); } } @@ -1271,7 +1271,7 @@ xfs_buf_iowait( XB_TRACE(bp, "iowait", 0); if (atomic_read(&bp->b_io_remaining)) blk_run_address_space(bp->b_target->bt_mapping); - down(&bp->b_iodonesema); + wait_for_completion(&bp->b_iowait); XB_TRACE(bp, "iowaited", (long)bp->b_error); return bp->b_error; } diff --git a/fs/xfs/linux-2.6/xfs_buf.h b/fs/xfs/linux-2.6/xfs_buf.h index 29d1d4adc07..fe010995665 100644 --- a/fs/xfs/linux-2.6/xfs_buf.h +++ b/fs/xfs/linux-2.6/xfs_buf.h @@ -157,7 +157,7 @@ typedef struct xfs_buf { xfs_buf_iodone_t b_iodone; /* I/O completion function */ xfs_buf_relse_t b_relse; /* releasing function */ xfs_buf_bdstrat_t b_strat; /* pre-write function */ - struct semaphore b_iodonesema; /* Semaphore for I/O waiters */ + struct completion b_iowait; /* queue for I/O waiters */ void *b_fspriv; void *b_fspriv2; void *b_fspriv3; @@ -352,7 +352,7 @@ extern void xfs_buf_trace(xfs_buf_t *, char *, void *, void *); #define XFS_BUF_CPSEMA(bp) (xfs_buf_cond_lock(bp) == 0) #define XFS_BUF_VSEMA(bp) xfs_buf_unlock(bp) #define XFS_BUF_PSEMA(bp,x) xfs_buf_lock(bp) -#define XFS_BUF_V_IODONESEMA(bp) up(&bp->b_iodonesema); +#define XFS_BUF_FINISH_IOWAIT(bp) complete(&bp->b_iowait); #define XFS_BUF_SET_TARGET(bp, target) ((bp)->b_target = (target)) #define XFS_BUF_TARGET(bp) ((bp)->b_target) diff --git a/fs/xfs/xfs_buf_item.c b/fs/xfs/xfs_buf_item.c index d86ca2c03a7..215c36dee32 100644 --- a/fs/xfs/xfs_buf_item.c +++ b/fs/xfs/xfs_buf_item.c @@ -1056,7 +1056,7 @@ xfs_buf_iodone_callbacks( anyway. */ XFS_BUF_SET_BRELSE_FUNC(bp,xfs_buf_error_relse); XFS_BUF_DONE(bp); - XFS_BUF_V_IODONESEMA(bp); + XFS_BUF_FINISH_IOWAIT(bp); } return; } diff --git a/fs/xfs/xfs_rw.c b/fs/xfs/xfs_rw.c index b0f31c09a76..3a82576dde9 100644 --- a/fs/xfs/xfs_rw.c +++ b/fs/xfs/xfs_rw.c @@ -314,7 +314,7 @@ xfs_bioerror_relse( * ASYNC buffers. */ XFS_BUF_ERROR(bp, EIO); - XFS_BUF_V_IODONESEMA(bp); + XFS_BUF_FINISH_IOWAIT(bp); } else { xfs_buf_relse(bp); } -- GitLab From 39d2f1ab2a36ac527a6c41cfe689f50c239eaca3 Mon Sep 17 00:00:00 2001 From: David Chinner Date: Wed, 13 Aug 2008 16:40:43 +1000 Subject: [PATCH 166/750] [XFS] extend completions to provide XFS object flush requirements XFS object flushing doesn't quite match existing completion semantics. It mixed exclusive access with completion. That is, we need to mark an object as being flushed before flushing it to disk, and then block any other attempt to flush it until the completion occurs. We do this but adding an extra count to the completion before we start using them. However, we still need to determine if there is a completion in progress, and allow no-blocking attempts fo completions to decrement the count. To do this we introduce: int try_wait_for_completion(struct completion *x) returns a failure status if done == 0, otherwise decrements done to zero and returns a "started" status. This is provided to allow counted completions to begin safely while holding object locks in inverted order. int completion_done(struct completion *x) returns 1 if there is no waiter, 0 if there is a waiter (i.e. a completion in progress). This replaces the use of semaphores for providing this exclusion and completion mechanism. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31816a Signed-off-by: David Chinner Signed-off-by: Lachlan McIlroy --- include/linux/completion.h | 45 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 45 insertions(+) diff --git a/include/linux/completion.h b/include/linux/completion.h index d2961b66d53..57faa60de9b 100644 --- a/include/linux/completion.h +++ b/include/linux/completion.h @@ -55,4 +55,49 @@ extern void complete_all(struct completion *); #define INIT_COMPLETION(x) ((x).done = 0) + +/** + * try_wait_for_completion - try to decrement a completion without blocking + * @x: completion structure + * + * Returns: 0 if a decrement cannot be done without blocking + * 1 if a decrement succeeded. + * + * If a completion is being used as a counting completion, + * attempt to decrement the counter without blocking. This + * enables us to avoid waiting if the resource the completion + * is protecting is not available. + */ +static inline bool try_wait_for_completion(struct completion *x) +{ + int ret = 1; + + spin_lock_irq(&x->wait.lock); + if (!x->done) + ret = 0; + else + x->done--; + spin_unlock_irq(&x->wait.lock); + return ret; +} + +/** + * completion_done - Test to see if a completion has any waiters + * @x: completion structure + * + * Returns: 0 if there are waiters (wait_for_completion() in progress) + * 1 if there are no waiters. + * + */ +static inline bool completion_done(struct completion *x) +{ + int ret = 1; + + spin_lock_irq(&x->wait.lock); + if (!x->done) + ret = 0; + spin_unlock_irq(&x->wait.lock); + return ret; +} + #endif -- GitLab From c63942d3eeffb98219e05d0976862ab9907d297d Mon Sep 17 00:00:00 2001 From: David Chinner Date: Wed, 13 Aug 2008 16:41:16 +1000 Subject: [PATCH 167/750] [XFS] replace inode flush semaphore with a completion Use the new completion flush code to implement the inode flush lock. Removes one of the final users of semaphores in the XFS code base. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31817a Signed-off-by: David Chinner Signed-off-by: Lachlan McIlroy --- fs/xfs/xfs_iget.c | 32 ++++++++------------------------ fs/xfs/xfs_inode.c | 11 +++++------ fs/xfs/xfs_inode.h | 25 +++++++++++++++++++++---- fs/xfs/xfs_inode_item.c | 11 +++++------ 4 files changed, 39 insertions(+), 40 deletions(-) diff --git a/fs/xfs/xfs_iget.c b/fs/xfs/xfs_iget.c index 539c2dd8eae..e229e9e001c 100644 --- a/fs/xfs/xfs_iget.c +++ b/fs/xfs/xfs_iget.c @@ -216,7 +216,14 @@ finish_inode: mrlock_init(&ip->i_iolock, MRLOCK_BARRIER, "xfsio", ip->i_ino); init_waitqueue_head(&ip->i_ipin_wait); atomic_set(&ip->i_pincount, 0); - initnsema(&ip->i_flock, 1, "xfsfino"); + + /* + * Because we want to use a counting completion, complete + * the flush completion once to allow a single access to + * the flush completion without blocking. + */ + init_completion(&ip->i_flush); + complete(&ip->i_flush); if (lock_flags) xfs_ilock(ip, lock_flags); @@ -783,26 +790,3 @@ xfs_isilocked( } #endif -/* - * The following three routines simply manage the i_flock - * semaphore embedded in the inode. This semaphore synchronizes - * processes attempting to flush the in-core inode back to disk. - */ -void -xfs_iflock(xfs_inode_t *ip) -{ - psema(&(ip->i_flock), PINOD|PLTWAIT); -} - -int -xfs_iflock_nowait(xfs_inode_t *ip) -{ - return (cpsema(&(ip->i_flock))); -} - -void -xfs_ifunlock(xfs_inode_t *ip) -{ - ASSERT(issemalocked(&(ip->i_flock))); - vsema(&(ip->i_flock)); -} diff --git a/fs/xfs/xfs_inode.c b/fs/xfs/xfs_inode.c index b8444ee4dc9..aea62222b3a 100644 --- a/fs/xfs/xfs_inode.c +++ b/fs/xfs/xfs_inode.c @@ -2626,7 +2626,6 @@ xfs_idestroy( xfs_idestroy_fork(ip, XFS_ATTR_FORK); mrfree(&ip->i_lock); mrfree(&ip->i_iolock); - freesema(&ip->i_flock); #ifdef XFS_INODE_TRACE ktrace_free(ip->i_trace); @@ -3044,10 +3043,10 @@ cluster_corrupt_out: /* * xfs_iflush() will write a modified inode's changes out to the * inode's on disk home. The caller must have the inode lock held - * in at least shared mode and the inode flush semaphore must be - * held as well. The inode lock will still be held upon return from + * in at least shared mode and the inode flush completion must be + * active as well. The inode lock will still be held upon return from * the call and the caller is free to unlock it. - * The inode flush lock will be unlocked when the inode reaches the disk. + * The inode flush will be completed when the inode reaches the disk. * The flags indicate how the inode's buffer should be written out. */ int @@ -3066,7 +3065,7 @@ xfs_iflush( XFS_STATS_INC(xs_iflush_count); ASSERT(xfs_isilocked(ip, XFS_ILOCK_EXCL|XFS_ILOCK_SHARED)); - ASSERT(issemalocked(&(ip->i_flock))); + ASSERT(!completion_done(&ip->i_flush)); ASSERT(ip->i_d.di_format != XFS_DINODE_FMT_BTREE || ip->i_d.di_nextents > ip->i_df.if_ext_max); @@ -3229,7 +3228,7 @@ xfs_iflush_int( #endif ASSERT(xfs_isilocked(ip, XFS_ILOCK_EXCL|XFS_ILOCK_SHARED)); - ASSERT(issemalocked(&(ip->i_flock))); + ASSERT(!completion_done(&ip->i_flush)); ASSERT(ip->i_d.di_format != XFS_DINODE_FMT_BTREE || ip->i_d.di_nextents > ip->i_df.if_ext_max); diff --git a/fs/xfs/xfs_inode.h b/fs/xfs/xfs_inode.h index 57172440435..f771df6bfa6 100644 --- a/fs/xfs/xfs_inode.h +++ b/fs/xfs/xfs_inode.h @@ -223,7 +223,7 @@ typedef struct xfs_inode { struct xfs_inode_log_item *i_itemp; /* logging information */ mrlock_t i_lock; /* inode lock */ mrlock_t i_iolock; /* inode IO lock */ - sema_t i_flock; /* inode flush lock */ + struct completion i_flush; /* inode flush completion q */ atomic_t i_pincount; /* inode pin count */ wait_queue_head_t i_ipin_wait; /* inode pinning wait queue */ spinlock_t i_flags_lock; /* inode i_flags lock */ @@ -482,11 +482,8 @@ int xfs_ilock_nowait(xfs_inode_t *, uint); void xfs_iunlock(xfs_inode_t *, uint); void xfs_ilock_demote(xfs_inode_t *, uint); int xfs_isilocked(xfs_inode_t *, uint); -void xfs_iflock(xfs_inode_t *); -int xfs_iflock_nowait(xfs_inode_t *); uint xfs_ilock_map_shared(xfs_inode_t *); void xfs_iunlock_map_shared(xfs_inode_t *, uint); -void xfs_ifunlock(xfs_inode_t *); void xfs_ireclaim(xfs_inode_t *); int xfs_finish_reclaim(xfs_inode_t *, int, int); int xfs_finish_reclaim_all(struct xfs_mount *, int); @@ -580,6 +577,26 @@ extern struct kmem_zone *xfs_ifork_zone; extern struct kmem_zone *xfs_inode_zone; extern struct kmem_zone *xfs_ili_zone; +/* + * Manage the i_flush queue embedded in the inode. This completion + * queue synchronizes processes attempting to flush the in-core + * inode back to disk. + */ +static inline void xfs_iflock(xfs_inode_t *ip) +{ + wait_for_completion(&ip->i_flush); +} + +static inline int xfs_iflock_nowait(xfs_inode_t *ip) +{ + return try_wait_for_completion(&ip->i_flush); +} + +static inline void xfs_ifunlock(xfs_inode_t *ip) +{ + complete(&ip->i_flush); +} + #endif /* __KERNEL__ */ #endif /* __XFS_INODE_H__ */ diff --git a/fs/xfs/xfs_inode_item.c b/fs/xfs/xfs_inode_item.c index 0eee08a32c2..97c7452e262 100644 --- a/fs/xfs/xfs_inode_item.c +++ b/fs/xfs/xfs_inode_item.c @@ -779,11 +779,10 @@ xfs_inode_item_pushbuf( ASSERT(iip->ili_push_owner == current_pid()); /* - * If flushlock isn't locked anymore, chances are that the - * inode flush completed and the inode was taken off the AIL. - * So, just get out. + * If a flush is not in progress anymore, chances are that the + * inode was taken off the AIL. So, just get out. */ - if (!issemalocked(&(ip->i_flock)) || + if (completion_done(&ip->i_flush) || ((iip->ili_item.li_flags & XFS_LI_IN_AIL) == 0)) { iip->ili_pushbuf_flag = 0; xfs_iunlock(ip, XFS_ILOCK_SHARED); @@ -805,7 +804,7 @@ xfs_inode_item_pushbuf( * If not, we can flush it async. */ dopush = ((iip->ili_item.li_flags & XFS_LI_IN_AIL) && - issemalocked(&(ip->i_flock))); + !completion_done(&ip->i_flush)); iip->ili_pushbuf_flag = 0; xfs_iunlock(ip, XFS_ILOCK_SHARED); xfs_buftrace("INODE ITEM PUSH", bp); @@ -858,7 +857,7 @@ xfs_inode_item_push( ip = iip->ili_inode; ASSERT(xfs_isilocked(ip, XFS_ILOCK_SHARED)); - ASSERT(issemalocked(&(ip->i_flock))); + ASSERT(!completion_done(&ip->i_flush)); /* * Since we were able to lock the inode's flush lock and * we found it on the AIL, the inode must be dirty. This -- GitLab From e1f49cf20cea18e3d1963939fe8612a75e319fbd Mon Sep 17 00:00:00 2001 From: David Chinner Date: Wed, 13 Aug 2008 16:41:43 +1000 Subject: [PATCH 168/750] [XFS] replace dquot flush semaphore with a completion Use the new completion flush code to implement the dquot flush lock. Removes one of the final users of semaphores in the XFS code base. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31822a Signed-off-by: David Chinner Signed-off-by: Lachlan McIlroy --- fs/xfs/quota/xfs_dquot.c | 34 ++++++++++++---------------------- fs/xfs/quota/xfs_dquot.h | 29 ++++++++++++++++++----------- fs/xfs/quota/xfs_dquot_item.c | 8 ++++---- fs/xfs/quota/xfs_qm.c | 8 ++++---- 4 files changed, 38 insertions(+), 41 deletions(-) diff --git a/fs/xfs/quota/xfs_dquot.c b/fs/xfs/quota/xfs_dquot.c index 9de42d03174..32290578c66 100644 --- a/fs/xfs/quota/xfs_dquot.c +++ b/fs/xfs/quota/xfs_dquot.c @@ -101,9 +101,16 @@ xfs_qm_dqinit( if (brandnewdquot) { dqp->dq_flnext = dqp->dq_flprev = dqp; mutex_init(&dqp->q_qlock); - initnsema(&dqp->q_flock, 1, "fdq"); sv_init(&dqp->q_pinwait, SV_DEFAULT, "pdq"); + /* + * Because we want to use a counting completion, complete + * the flush completion once to allow a single access to + * the flush completion without blocking. + */ + init_completion(&dqp->q_flush); + complete(&dqp->q_flush); + #ifdef XFS_DQUOT_TRACE dqp->q_trace = ktrace_alloc(DQUOT_TRACE_SIZE, KM_SLEEP); xfs_dqtrace_entry(dqp, "DQINIT"); @@ -150,7 +157,6 @@ xfs_qm_dqdestroy( ASSERT(! XFS_DQ_IS_ON_FREELIST(dqp)); mutex_destroy(&dqp->q_qlock); - freesema(&dqp->q_flock); sv_destroy(&dqp->q_pinwait); #ifdef XFS_DQUOT_TRACE @@ -1211,7 +1217,7 @@ xfs_qm_dqflush( int error; ASSERT(XFS_DQ_IS_LOCKED(dqp)); - ASSERT(XFS_DQ_IS_FLUSH_LOCKED(dqp)); + ASSERT(!completion_done(&dqp->q_flush)); xfs_dqtrace_entry(dqp, "DQFLUSH"); /* @@ -1348,34 +1354,18 @@ xfs_qm_dqflush_done( xfs_dqfunlock(dqp); } - -int -xfs_qm_dqflock_nowait( - xfs_dquot_t *dqp) -{ - int locked; - - locked = cpsema(&((dqp)->q_flock)); - - /* XXX ifdef these out */ - if (locked) - (dqp)->dq_flags |= XFS_DQ_FLOCKED; - return (locked); -} - - int xfs_qm_dqlock_nowait( xfs_dquot_t *dqp) { - return (mutex_trylock(&((dqp)->q_qlock))); + return mutex_trylock(&dqp->q_qlock); } void xfs_dqlock( xfs_dquot_t *dqp) { - mutex_lock(&(dqp->q_qlock)); + mutex_lock(&dqp->q_qlock); } void @@ -1468,7 +1458,7 @@ xfs_qm_dqpurge( * if we're turning off quotas. Basically, we need this flush * lock, and are willing to block on it. */ - if (! xfs_qm_dqflock_nowait(dqp)) { + if (!xfs_dqflock_nowait(dqp)) { /* * Block on the flush lock after nudging dquot buffer, * if it is incore. diff --git a/fs/xfs/quota/xfs_dquot.h b/fs/xfs/quota/xfs_dquot.h index f7393bba4e9..8958d0faf8d 100644 --- a/fs/xfs/quota/xfs_dquot.h +++ b/fs/xfs/quota/xfs_dquot.h @@ -82,7 +82,7 @@ typedef struct xfs_dquot { xfs_qcnt_t q_res_icount; /* total inos allocd+reserved */ xfs_qcnt_t q_res_rtbcount;/* total realtime blks used+reserved */ mutex_t q_qlock; /* quota lock */ - sema_t q_flock; /* flush lock */ + struct completion q_flush; /* flush completion queue */ uint q_pincount; /* pin count for this dquot */ sv_t q_pinwait; /* sync var for pinning */ #ifdef XFS_DQUOT_TRACE @@ -113,17 +113,25 @@ XFS_DQ_IS_LOCKED(xfs_dquot_t *dqp) /* - * The following three routines simply manage the q_flock - * semaphore embedded in the dquot. This semaphore synchronizes - * processes attempting to flush the in-core dquot back to disk. + * Manage the q_flush completion queue embedded in the dquot. This completion + * queue synchronizes processes attempting to flush the in-core dquot back to + * disk. */ -#define xfs_dqflock(dqp) { psema(&((dqp)->q_flock), PINOD | PRECALC);\ - (dqp)->dq_flags |= XFS_DQ_FLOCKED; } -#define xfs_dqfunlock(dqp) { ASSERT(issemalocked(&((dqp)->q_flock))); \ - vsema(&((dqp)->q_flock)); \ - (dqp)->dq_flags &= ~(XFS_DQ_FLOCKED); } +static inline void xfs_dqflock(xfs_dquot_t *dqp) +{ + wait_for_completion(&dqp->q_flush); +} + +static inline int xfs_dqflock_nowait(xfs_dquot_t *dqp) +{ + return try_wait_for_completion(&dqp->q_flush); +} + +static inline void xfs_dqfunlock(xfs_dquot_t *dqp) +{ + complete(&dqp->q_flush); +} -#define XFS_DQ_IS_FLUSH_LOCKED(dqp) (issemalocked(&((dqp)->q_flock))) #define XFS_DQ_IS_ON_FREELIST(dqp) ((dqp)->dq_flnext != (dqp)) #define XFS_DQ_IS_DIRTY(dqp) ((dqp)->dq_flags & XFS_DQ_DIRTY) #define XFS_QM_ISUDQ(dqp) ((dqp)->dq_flags & XFS_DQ_USER) @@ -167,7 +175,6 @@ extern int xfs_qm_dqflush(xfs_dquot_t *, uint); extern int xfs_qm_dqpurge(xfs_dquot_t *); extern void xfs_qm_dqunpin_wait(xfs_dquot_t *); extern int xfs_qm_dqlock_nowait(xfs_dquot_t *); -extern int xfs_qm_dqflock_nowait(xfs_dquot_t *); extern void xfs_qm_dqflock_pushbuf_wait(xfs_dquot_t *dqp); extern void xfs_qm_adjust_dqtimers(xfs_mount_t *, xfs_disk_dquot_t *); diff --git a/fs/xfs/quota/xfs_dquot_item.c b/fs/xfs/quota/xfs_dquot_item.c index 08d2fc89e6a..f028644caa5 100644 --- a/fs/xfs/quota/xfs_dquot_item.c +++ b/fs/xfs/quota/xfs_dquot_item.c @@ -151,7 +151,7 @@ xfs_qm_dquot_logitem_push( dqp = logitem->qli_dquot; ASSERT(XFS_DQ_IS_LOCKED(dqp)); - ASSERT(XFS_DQ_IS_FLUSH_LOCKED(dqp)); + ASSERT(!completion_done(&dqp->q_flush)); /* * Since we were able to lock the dquot's flush lock and @@ -245,7 +245,7 @@ xfs_qm_dquot_logitem_pushbuf( * inode flush completed and the inode was taken off the AIL. * So, just get out. */ - if (!issemalocked(&(dqp->q_flock)) || + if (completion_done(&dqp->q_flush) || ((qip->qli_item.li_flags & XFS_LI_IN_AIL) == 0)) { qip->qli_pushbuf_flag = 0; xfs_dqunlock(dqp); @@ -258,7 +258,7 @@ xfs_qm_dquot_logitem_pushbuf( if (bp != NULL) { if (XFS_BUF_ISDELAYWRITE(bp)) { dopush = ((qip->qli_item.li_flags & XFS_LI_IN_AIL) && - issemalocked(&(dqp->q_flock))); + !completion_done(&dqp->q_flush)); qip->qli_pushbuf_flag = 0; xfs_dqunlock(dqp); @@ -317,7 +317,7 @@ xfs_qm_dquot_logitem_trylock( return (XFS_ITEM_LOCKED); retval = XFS_ITEM_SUCCESS; - if (! xfs_qm_dqflock_nowait(dqp)) { + if (!xfs_dqflock_nowait(dqp)) { /* * The dquot is already being flushed. It may have been * flushed delayed write, however, and we don't want to diff --git a/fs/xfs/quota/xfs_qm.c b/fs/xfs/quota/xfs_qm.c index 021934a3d45..3825d748407 100644 --- a/fs/xfs/quota/xfs_qm.c +++ b/fs/xfs/quota/xfs_qm.c @@ -484,7 +484,7 @@ again: xfs_dqtrace_entry(dqp, "FLUSHALL: DQDIRTY"); /* XXX a sentinel would be better */ recl = XFS_QI_MPLRECLAIMS(mp); - if (! xfs_qm_dqflock_nowait(dqp)) { + if (!xfs_dqflock_nowait(dqp)) { /* * If we can't grab the flush lock then check * to see if the dquot has been flushed delayed @@ -1062,7 +1062,7 @@ xfs_qm_sync( /* XXX a sentinel would be better */ recl = XFS_QI_MPLRECLAIMS(mp); - if (! xfs_qm_dqflock_nowait(dqp)) { + if (!xfs_dqflock_nowait(dqp)) { if (nowait) { xfs_dqunlock(dqp); continue; @@ -2079,7 +2079,7 @@ xfs_qm_shake_freelist( * Try to grab the flush lock. If this dquot is in the process of * getting flushed to disk, we don't want to reclaim it. */ - if (! xfs_qm_dqflock_nowait(dqp)) { + if (!xfs_dqflock_nowait(dqp)) { xfs_dqunlock(dqp); dqp = dqp->dq_flnext; continue; @@ -2257,7 +2257,7 @@ xfs_qm_dqreclaim_one(void) * Try to grab the flush lock. If this dquot is in the process of * getting flushed to disk, we don't want to reclaim it. */ - if (! xfs_qm_dqflock_nowait(dqp)) { + if (!xfs_dqflock_nowait(dqp)) { xfs_dqunlock(dqp); continue; } -- GitLab From ab4a9b04a33c97dd17495f943447f5a15ecf2b51 Mon Sep 17 00:00:00 2001 From: David Chinner Date: Wed, 13 Aug 2008 16:42:10 +1000 Subject: [PATCH 169/750] [XFS] remove the sema_t from XFS. Now that all users of the sema_t are gone from XFS we can finally kill it. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31823a Signed-off-by: David Chinner Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/sema.h | 52 ------------------------------------ fs/xfs/linux-2.6/xfs_linux.h | 2 +- 2 files changed, 1 insertion(+), 53 deletions(-) delete mode 100644 fs/xfs/linux-2.6/sema.h diff --git a/fs/xfs/linux-2.6/sema.h b/fs/xfs/linux-2.6/sema.h deleted file mode 100644 index 3abe7e9ceb3..00000000000 --- a/fs/xfs/linux-2.6/sema.h +++ /dev/null @@ -1,52 +0,0 @@ -/* - * Copyright (c) 2000-2002,2005 Silicon Graphics, Inc. - * All Rights Reserved. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it would be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write the Free Software Foundation, - * Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA - */ -#ifndef __XFS_SUPPORT_SEMA_H__ -#define __XFS_SUPPORT_SEMA_H__ - -#include -#include -#include -#include - -/* - * sema_t structure just maps to struct semaphore in Linux kernel. - */ - -typedef struct semaphore sema_t; - -#define initnsema(sp, val, name) sema_init(sp, val) -#define psema(sp, b) down(sp) -#define vsema(sp) up(sp) -#define freesema(sema) do { } while (0) - -static inline int issemalocked(sema_t *sp) -{ - return down_trylock(sp) || (up(sp), 0); -} - -/* - * Map cpsema (try to get the sema) to down_trylock. We need to switch - * the return values since cpsema returns 1 (acquired) 0 (failed) and - * down_trylock returns the reverse 0 (acquired) 1 (failed). - */ -static inline int cpsema(sema_t *sp) -{ - return down_trylock(sp) ? 0 : 1; -} - -#endif /* __XFS_SUPPORT_SEMA_H__ */ diff --git a/fs/xfs/linux-2.6/xfs_linux.h b/fs/xfs/linux-2.6/xfs_linux.h index 1b8dfdcac0a..3b7c4ff48ba 100644 --- a/fs/xfs/linux-2.6/xfs_linux.h +++ b/fs/xfs/linux-2.6/xfs_linux.h @@ -45,13 +45,13 @@ #include #include #include -#include #include #include #include #include +#include #include #include #include -- GitLab From dff35fd41f252476cba7f761d7204dd9f47d739e Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:44:15 +1000 Subject: [PATCH 170/750] [XFS] update timestamp in xfs_ialloc manually In xfs_ialloc we just want to set all timestamps to the current time. We don't need to mark the inode dirty like xfs_ichgtime does, and we don't need nor want the opimizations in xfs_ichgtime that I will introduce in the next patch. So just opencode the timestamp update in xfs_ialloc, and remove the new unused XFS_ICHGTIME_ACC case in xfs_ichgtime. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31825a Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_iops.c | 17 ----------------- fs/xfs/xfs_inode.c | 9 ++++++++- fs/xfs/xfs_inode.h | 3 +-- fs/xfs/xfs_vnodeops.c | 1 - 4 files changed, 9 insertions(+), 21 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_iops.c b/fs/xfs/linux-2.6/xfs_iops.c index ace56bd3a5f..d6947f818f2 100644 --- a/fs/xfs/linux-2.6/xfs_iops.c +++ b/fs/xfs/linux-2.6/xfs_iops.c @@ -89,12 +89,6 @@ xfs_mark_inode_dirty_sync( * Change the requested timestamp in the given inode. * We don't lock across timestamp updates, and we don't log them but * we do record the fact that there is dirty information in core. - * - * NOTE -- callers MUST combine XFS_ICHGTIME_MOD or XFS_ICHGTIME_CHG - * with XFS_ICHGTIME_ACC to be sure that access time - * update will take. Calling first with XFS_ICHGTIME_ACC - * and then XFS_ICHGTIME_MOD may fail to modify the access - * timestamp if the filesystem is mounted noacctm. */ void xfs_ichgtime( @@ -110,11 +104,6 @@ xfs_ichgtime( ip->i_d.di_mtime.t_sec = (__int32_t)tv.tv_sec; ip->i_d.di_mtime.t_nsec = (__int32_t)tv.tv_nsec; } - if (flags & XFS_ICHGTIME_ACC) { - inode->i_atime = tv; - ip->i_d.di_atime.t_sec = (__int32_t)tv.tv_sec; - ip->i_d.di_atime.t_nsec = (__int32_t)tv.tv_nsec; - } if (flags & XFS_ICHGTIME_CHG) { inode->i_ctime = tv; ip->i_d.di_ctime.t_sec = (__int32_t)tv.tv_sec; @@ -149,12 +138,6 @@ xfs_ichgtime_fast( { timespec_t *tvp; - /* - * Atime updates for read() & friends are handled lazily now, and - * explicit updates must go through xfs_ichgtime() - */ - ASSERT((flags & XFS_ICHGTIME_ACC) == 0); - if (flags & XFS_ICHGTIME_MOD) { tvp = &inode->i_mtime; ip->i_d.di_mtime.t_sec = (__int32_t)tvp->tv_sec; diff --git a/fs/xfs/xfs_inode.c b/fs/xfs/xfs_inode.c index aea62222b3a..41371c56f36 100644 --- a/fs/xfs/xfs_inode.c +++ b/fs/xfs/xfs_inode.c @@ -1048,6 +1048,7 @@ xfs_ialloc( xfs_inode_t *ip; uint flags; int error; + timespec_t tv; /* * Call the space management code to pick @@ -1128,7 +1129,13 @@ xfs_ialloc( ip->i_size = 0; ip->i_d.di_nextents = 0; ASSERT(ip->i_d.di_nblocks == 0); - xfs_ichgtime(ip, XFS_ICHGTIME_CHG|XFS_ICHGTIME_ACC|XFS_ICHGTIME_MOD); + + nanotime(&tv); + ip->i_d.di_mtime.t_sec = (__int32_t)tv.tv_sec; + ip->i_d.di_mtime.t_nsec = (__int32_t)tv.tv_nsec; + ip->i_d.di_atime = ip->i_d.di_mtime; + ip->i_d.di_ctime = ip->i_d.di_mtime; + /* * di_gen will have been taken care of in xfs_iread. */ diff --git a/fs/xfs/xfs_inode.h b/fs/xfs/xfs_inode.h index f771df6bfa6..1420c49674d 100644 --- a/fs/xfs/xfs_inode.h +++ b/fs/xfs/xfs_inode.h @@ -87,8 +87,7 @@ typedef struct xfs_ifork { * Flags for xfs_ichgtime(). */ #define XFS_ICHGTIME_MOD 0x1 /* data fork modification timestamp */ -#define XFS_ICHGTIME_ACC 0x2 /* data fork access timestamp */ -#define XFS_ICHGTIME_CHG 0x4 /* inode field change timestamp */ +#define XFS_ICHGTIME_CHG 0x2 /* inode field change timestamp */ /* * Per-fork incore inode flags. diff --git a/fs/xfs/xfs_vnodeops.c b/fs/xfs/xfs_vnodeops.c index 7b967c096d0..588bb4aa215 100644 --- a/fs/xfs/xfs_vnodeops.c +++ b/fs/xfs/xfs_vnodeops.c @@ -513,7 +513,6 @@ xfs_setattr( ip->i_d.di_atime.t_sec = iattr->ia_atime.tv_sec; ip->i_d.di_atime.t_nsec = iattr->ia_atime.tv_nsec; ip->i_update_core = 1; - timeflags &= ~XFS_ICHGTIME_ACC; } if (mask & ATTR_MTIME) { inode->i_mtime = iattr->ia_mtime; -- GitLab From 8e5975c82f66bce36955f38e9abc259d5143a72a Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:45:13 +1000 Subject: [PATCH 171/750] [XFS] optimize xfs_ichgtime Port a little optmization from file_update_time to xfs_ichgtime, and only update the timestamp and mark the inode dirty if the timestamp actually changes in the timer tick resultion supported by the running kernel. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31827a Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_iops.c | 19 +++++++++++++------ 1 file changed, 13 insertions(+), 6 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_iops.c b/fs/xfs/linux-2.6/xfs_iops.c index d6947f818f2..0e7ca215595 100644 --- a/fs/xfs/linux-2.6/xfs_iops.c +++ b/fs/xfs/linux-2.6/xfs_iops.c @@ -97,17 +97,23 @@ xfs_ichgtime( { struct inode *inode = VFS_I(ip); timespec_t tv; + int sync_it = 0; - nanotime(&tv); - if (flags & XFS_ICHGTIME_MOD) { + tv = current_fs_time(inode->i_sb); + + if ((flags & XFS_ICHGTIME_MOD) && + !timespec_equal(&inode->i_mtime, &tv)) { inode->i_mtime = tv; ip->i_d.di_mtime.t_sec = (__int32_t)tv.tv_sec; ip->i_d.di_mtime.t_nsec = (__int32_t)tv.tv_nsec; + sync_it = 1; } - if (flags & XFS_ICHGTIME_CHG) { + if ((flags & XFS_ICHGTIME_CHG) && + !timespec_equal(&inode->i_ctime, &tv)) { inode->i_ctime = tv; ip->i_d.di_ctime.t_sec = (__int32_t)tv.tv_sec; ip->i_d.di_ctime.t_nsec = (__int32_t)tv.tv_nsec; + sync_it = 1; } /* @@ -119,10 +125,11 @@ xfs_ichgtime( * ensure that the compiler does not reorder the update * of i_update_core above the timestamp updates above. */ - SYNCHRONIZE(); - ip->i_update_core = 1; - if (!(inode->i_state & I_NEW)) + if (sync_it) { + SYNCHRONIZE(); + ip->i_update_core = 1; mark_inode_dirty_sync(inode); + } } /* -- GitLab From 3a76c1ea07ee4e9da7c8e476e43be7e1b2bf24fb Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:48:12 +1000 Subject: [PATCH 172/750] [XFS] stop using file_update_time xfs_ichtime updates the xfs_inode and Linux inode timestamps just fine, no need to call file_update_time and then copy the values over to the XFS inode. The only additional thing in file_update_time are checks not applicable to the write path. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31829a Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy Signed-off-by: David Chinner --- fs/xfs/linux-2.6/xfs_iops.c | 39 ------------------------------------- fs/xfs/linux-2.6/xfs_iops.h | 3 --- fs/xfs/linux-2.6/xfs_lrw.c | 4 +--- 3 files changed, 1 insertion(+), 45 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_iops.c b/fs/xfs/linux-2.6/xfs_iops.c index 0e7ca215595..91bcd979242 100644 --- a/fs/xfs/linux-2.6/xfs_iops.c +++ b/fs/xfs/linux-2.6/xfs_iops.c @@ -132,45 +132,6 @@ xfs_ichgtime( } } -/* - * Variant on the above which avoids querying the system clock - * in situations where we know the Linux inode timestamps have - * just been updated (and so we can update our inode cheaply). - */ -void -xfs_ichgtime_fast( - xfs_inode_t *ip, - struct inode *inode, - int flags) -{ - timespec_t *tvp; - - if (flags & XFS_ICHGTIME_MOD) { - tvp = &inode->i_mtime; - ip->i_d.di_mtime.t_sec = (__int32_t)tvp->tv_sec; - ip->i_d.di_mtime.t_nsec = (__int32_t)tvp->tv_nsec; - } - if (flags & XFS_ICHGTIME_CHG) { - tvp = &inode->i_ctime; - ip->i_d.di_ctime.t_sec = (__int32_t)tvp->tv_sec; - ip->i_d.di_ctime.t_nsec = (__int32_t)tvp->tv_nsec; - } - - /* - * We update the i_update_core field _after_ changing - * the timestamps in order to coordinate properly with - * xfs_iflush() so that we don't lose timestamp updates. - * This keeps us from having to hold the inode lock - * while doing this. We use the SYNCHRONIZE macro to - * ensure that the compiler does not reorder the update - * of i_update_core above the timestamp updates above. - */ - SYNCHRONIZE(); - ip->i_update_core = 1; - if (!(inode->i_state & I_NEW)) - mark_inode_dirty_sync(inode); -} - /* * Hook in SELinux. This is not quite correct yet, what we really need * here (as we do for default ACLs) is a mechanism by which creation of diff --git a/fs/xfs/linux-2.6/xfs_iops.h b/fs/xfs/linux-2.6/xfs_iops.h index 2204f466dee..8b1a1e31dc2 100644 --- a/fs/xfs/linux-2.6/xfs_iops.h +++ b/fs/xfs/linux-2.6/xfs_iops.h @@ -26,9 +26,6 @@ extern const struct file_operations xfs_invis_file_operations; extern ssize_t xfs_vn_listxattr(struct dentry *, char *data, size_t size); -extern void xfs_ichgtime(struct xfs_inode *, int); -extern void xfs_ichgtime_fast(struct xfs_inode *, struct inode *, int); - extern void xfs_setup_inode(struct xfs_inode *); #endif /* __XFS_IOPS_H__ */ diff --git a/fs/xfs/linux-2.6/xfs_lrw.c b/fs/xfs/linux-2.6/xfs_lrw.c index e03e2c3789b..1957e5357d0 100644 --- a/fs/xfs/linux-2.6/xfs_lrw.c +++ b/fs/xfs/linux-2.6/xfs_lrw.c @@ -674,9 +674,7 @@ start: */ if (likely(!(ioflags & IO_INVIS) && !mnt_want_write(file->f_path.mnt))) { - file_update_time(file); - xfs_ichgtime_fast(xip, inode, - XFS_ICHGTIME_MOD | XFS_ICHGTIME_CHG); + xfs_ichgtime(xip, XFS_ICHGTIME_MOD | XFS_ICHGTIME_CHG); mnt_drop_write(file->f_path.mnt); } -- GitLab From 77508ec8e6ed72c9ba8ca74248a7aabd664e3f57 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:49:04 +1000 Subject: [PATCH 173/750] [XFS] move root inode IRELE into xfs_unmountfs The root inode is allocated in xfs_mountfs so it should be release in xfs_unmountfs. For the unmount case that means we do it after the the xfs_sync(mp, SYNC_WAIT | SYNC_CLOSE) in the forced shutdown case and the dmapi unmount event. Note that both reference the rip variable which might be freed by that time in case inode flushing has kicked in, so strictly speaking this might count as a bug fix SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31830a Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_super.c | 4 ---- fs/xfs/xfs_mount.c | 2 ++ 2 files changed, 2 insertions(+), 4 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_super.c b/fs/xfs/linux-2.6/xfs_super.c index 0eaad84a680..9ccbb1ca277 100644 --- a/fs/xfs/linux-2.6/xfs_super.c +++ b/fs/xfs/linux-2.6/xfs_super.c @@ -1131,8 +1131,6 @@ xfs_fs_put_super( error = xfs_unmount_flush(mp, 0); WARN_ON(error); - IRELE(rip); - /* * If we're forcing a shutdown, typically because of a media error, * we want to make sure we invalidate dirty pages that belong to @@ -1804,8 +1802,6 @@ xfs_fs_fill_super( error = xfs_unmount_flush(mp, 0); WARN_ON(error); - IRELE(mp->m_rootip); - xfs_unmountfs(mp); goto out_free_fsname; } diff --git a/fs/xfs/xfs_mount.c b/fs/xfs/xfs_mount.c index 6b4350700c0..73f0ba1ec19 100644 --- a/fs/xfs/xfs_mount.c +++ b/fs/xfs/xfs_mount.c @@ -1250,6 +1250,8 @@ xfs_unmountfs(xfs_mount_t *mp) __uint64_t resblks; int error = 0; + IRELE(mp->m_rootip); + /* * We can potentially deadlock here if we have an inode cluster * that has been freed has it's buffer still pinned in memory because -- GitLab From 4249023a5d14f28d4e68ba15d24d25c0e5be71a6 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:49:32 +1000 Subject: [PATCH 174/750] [XFS] cleanup xfs_mountfs Remove all the useless flags and code keyed off it in xfs_mountfs. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31831a Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_super.c | 2 +- fs/xfs/quota/xfs_qm.c | 6 ++---- fs/xfs/quota/xfs_qm.h | 2 +- fs/xfs/quota/xfs_qm_bhv.c | 7 +++---- fs/xfs/xfs_log.c | 4 ++-- fs/xfs/xfs_log.h | 2 +- fs/xfs/xfs_log_priv.h | 2 +- fs/xfs/xfs_log_recover.c | 7 ++----- fs/xfs/xfs_mount.c | 30 ++++++++++-------------------- fs/xfs/xfs_mount.h | 15 ++++----------- 10 files changed, 27 insertions(+), 50 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_super.c b/fs/xfs/linux-2.6/xfs_super.c index 9ccbb1ca277..8fdb79046a6 100644 --- a/fs/xfs/linux-2.6/xfs_super.c +++ b/fs/xfs/linux-2.6/xfs_super.c @@ -1722,7 +1722,7 @@ xfs_fs_fill_super( if (error) goto out_free_sb; - error = xfs_mountfs(mp, flags); + error = xfs_mountfs(mp); if (error) goto out_filestream_unmount; diff --git a/fs/xfs/quota/xfs_qm.c b/fs/xfs/quota/xfs_qm.c index 3825d748407..df0ffef9775 100644 --- a/fs/xfs/quota/xfs_qm.c +++ b/fs/xfs/quota/xfs_qm.c @@ -310,8 +310,7 @@ xfs_qm_unmount_quotadestroy( */ void xfs_qm_mount_quotas( - xfs_mount_t *mp, - int mfsi_flags) + xfs_mount_t *mp) { int error = 0; uint sbf; @@ -346,8 +345,7 @@ xfs_qm_mount_quotas( /* * If any of the quotas are not consistent, do a quotacheck. */ - if (XFS_QM_NEED_QUOTACHECK(mp) && - !(mfsi_flags & XFS_MFSI_NO_QUOTACHECK)) { + if (XFS_QM_NEED_QUOTACHECK(mp)) { error = xfs_qm_quotacheck(mp); if (error) { /* Quotacheck failed and disabled quotas. */ diff --git a/fs/xfs/quota/xfs_qm.h b/fs/xfs/quota/xfs_qm.h index cd2300e374a..44f25349e47 100644 --- a/fs/xfs/quota/xfs_qm.h +++ b/fs/xfs/quota/xfs_qm.h @@ -165,7 +165,7 @@ typedef struct xfs_dquot_acct { #define XFS_QM_RELE(xqm) ((xqm)->qm_nrefs--) extern void xfs_qm_destroy_quotainfo(xfs_mount_t *); -extern void xfs_qm_mount_quotas(xfs_mount_t *, int); +extern void xfs_qm_mount_quotas(xfs_mount_t *); extern int xfs_qm_quotacheck(xfs_mount_t *); extern void xfs_qm_unmount_quotadestroy(xfs_mount_t *); extern int xfs_qm_unmount_quotas(xfs_mount_t *); diff --git a/fs/xfs/quota/xfs_qm_bhv.c b/fs/xfs/quota/xfs_qm_bhv.c index f4f6c4c861d..eea2e60b456 100644 --- a/fs/xfs/quota/xfs_qm_bhv.c +++ b/fs/xfs/quota/xfs_qm_bhv.c @@ -162,7 +162,7 @@ xfs_qm_newmount( * mounting, and get on with the boring life * without disk quotas. */ - xfs_qm_mount_quotas(mp, 0); + xfs_qm_mount_quotas(mp); } else { /* * Clear the quota flags, but remember them. This @@ -184,13 +184,12 @@ STATIC int xfs_qm_endmount( xfs_mount_t *mp, uint needquotamount, - uint quotaflags, - int mfsi_flags) + uint quotaflags) { if (needquotamount) { ASSERT(mp->m_qflags == 0); mp->m_qflags = quotaflags; - xfs_qm_mount_quotas(mp, mfsi_flags); + xfs_qm_mount_quotas(mp); } #if defined(DEBUG) && defined(XFS_LOUD_RECOVERY) diff --git a/fs/xfs/xfs_log.c b/fs/xfs/xfs_log.c index 0816c5d6d76..9c23864d4fd 100644 --- a/fs/xfs/xfs_log.c +++ b/fs/xfs/xfs_log.c @@ -588,12 +588,12 @@ error: * mp - ubiquitous xfs mount point structure */ int -xfs_log_mount_finish(xfs_mount_t *mp, int mfsi_flags) +xfs_log_mount_finish(xfs_mount_t *mp) { int error; if (!(mp->m_flags & XFS_MOUNT_NORECOVERY)) - error = xlog_recover_finish(mp->m_log, mfsi_flags); + error = xlog_recover_finish(mp->m_log); else { error = 0; ASSERT(mp->m_flags & XFS_MOUNT_RDONLY); diff --git a/fs/xfs/xfs_log.h b/fs/xfs/xfs_log.h index d1d678ecb63..d47b91f1082 100644 --- a/fs/xfs/xfs_log.h +++ b/fs/xfs/xfs_log.h @@ -149,7 +149,7 @@ int xfs_log_mount(struct xfs_mount *mp, struct xfs_buftarg *log_target, xfs_daddr_t start_block, int num_bblocks); -int xfs_log_mount_finish(struct xfs_mount *mp, int); +int xfs_log_mount_finish(struct xfs_mount *mp); void xfs_log_move_tail(struct xfs_mount *mp, xfs_lsn_t tail_lsn); int xfs_log_notify(struct xfs_mount *mp, diff --git a/fs/xfs/xfs_log_priv.h b/fs/xfs/xfs_log_priv.h index 7dcf11e0b2f..c8a5b22ee3e 100644 --- a/fs/xfs/xfs_log_priv.h +++ b/fs/xfs/xfs_log_priv.h @@ -468,7 +468,7 @@ extern int xlog_find_tail(xlog_t *log, xfs_daddr_t *head_blk, xfs_daddr_t *tail_blk); extern int xlog_recover(xlog_t *log); -extern int xlog_recover_finish(xlog_t *log, int mfsi_flags); +extern int xlog_recover_finish(xlog_t *log); extern void xlog_pack_data(xlog_t *log, xlog_in_core_t *iclog, int); extern void xlog_recover_process_iunlinks(xlog_t *log); diff --git a/fs/xfs/xfs_log_recover.c b/fs/xfs/xfs_log_recover.c index 9eb722ec744..82d46ce69d5 100644 --- a/fs/xfs/xfs_log_recover.c +++ b/fs/xfs/xfs_log_recover.c @@ -3940,8 +3940,7 @@ xlog_recover( */ int xlog_recover_finish( - xlog_t *log, - int mfsi_flags) + xlog_t *log) { /* * Now we're ready to do the transactions needed for the @@ -3969,9 +3968,7 @@ xlog_recover_finish( xfs_log_force(log->l_mp, (xfs_lsn_t)0, (XFS_LOG_FORCE | XFS_LOG_SYNC)); - if ( (mfsi_flags & XFS_MFSI_NOUNLINK) == 0 ) { - xlog_recover_process_iunlinks(log); - } + xlog_recover_process_iunlinks(log); xlog_recover_check_summary(log); diff --git a/fs/xfs/xfs_mount.c b/fs/xfs/xfs_mount.c index 73f0ba1ec19..06f0a73bc93 100644 --- a/fs/xfs/xfs_mount.c +++ b/fs/xfs/xfs_mount.c @@ -697,11 +697,11 @@ xfs_initialize_perag_data(xfs_mount_t *mp, xfs_agnumber_t agcount) * Update alignment values based on mount options and sb values */ STATIC int -xfs_update_alignment(xfs_mount_t *mp, int mfsi_flags, __uint64_t *update_flags) +xfs_update_alignment(xfs_mount_t *mp, __uint64_t *update_flags) { xfs_sb_t *sbp = &(mp->m_sb); - if (mp->m_dalign && !(mfsi_flags & XFS_MFSI_SECOND)) { + if (mp->m_dalign) { /* * If stripe unit and stripe width are not multiples * of the fs blocksize turn off alignment. @@ -857,7 +857,7 @@ xfs_set_inoalignment(xfs_mount_t *mp) * Check that the data (and log if separate) are an ok size. */ STATIC int -xfs_check_sizes(xfs_mount_t *mp, int mfsi_flags) +xfs_check_sizes(xfs_mount_t *mp) { xfs_buf_t *bp; xfs_daddr_t d; @@ -880,8 +880,7 @@ xfs_check_sizes(xfs_mount_t *mp, int mfsi_flags) return error; } - if (((mfsi_flags & XFS_MFSI_CLIENT) == 0) && - mp->m_logdev_targp != mp->m_ddev_targp) { + if (mp->m_logdev_targp != mp->m_ddev_targp) { d = (xfs_daddr_t)XFS_FSB_TO_BB(mp, mp->m_sb.sb_logblocks); if (XFS_BB_TO_FSB(mp, d) != mp->m_sb.sb_logblocks) { cmn_err(CE_WARN, "XFS: size check 3 failed"); @@ -916,8 +915,7 @@ xfs_check_sizes(xfs_mount_t *mp, int mfsi_flags) */ int xfs_mountfs( - xfs_mount_t *mp, - int mfsi_flags) + xfs_mount_t *mp) { xfs_sb_t *sbp = &(mp->m_sb); xfs_inode_t *rip; @@ -978,7 +976,7 @@ xfs_mountfs( * allocator alignment is within an ag, therefore ag has * to be aligned at stripe boundary. */ - error = xfs_update_alignment(mp, mfsi_flags, &update_flags); + error = xfs_update_alignment(mp, &update_flags); if (error) goto error1; @@ -997,8 +995,7 @@ xfs_mountfs( * since a single partition filesystem is identical to a single * partition volume/filesystem. */ - if ((mfsi_flags & XFS_MFSI_SECOND) == 0 && - (mp->m_flags & XFS_MOUNT_NOUUID) == 0) { + if ((mp->m_flags & XFS_MOUNT_NOUUID) == 0) { if (xfs_uuid_mount(mp)) { error = XFS_ERROR(EINVAL); goto error1; @@ -1026,7 +1023,7 @@ xfs_mountfs( /* * Check that the data (and log if separate) are an ok size. */ - error = xfs_check_sizes(mp, mfsi_flags); + error = xfs_check_sizes(mp); if (error) goto error1; @@ -1039,13 +1036,6 @@ xfs_mountfs( goto error1; } - /* - * For client case we are done now - */ - if (mfsi_flags & XFS_MFSI_CLIENT) { - return 0; - } - /* * Copies the low order bits of the timestamp and the randomly * set "sequence" number out of a UUID. @@ -1183,7 +1173,7 @@ xfs_mountfs( * delayed until after the root and real-time bitmap inodes * were consistently read in. */ - error = xfs_log_mount_finish(mp, mfsi_flags); + error = xfs_log_mount_finish(mp); if (error) { cmn_err(CE_WARN, "XFS: log mount finish failed"); goto error4; @@ -1192,7 +1182,7 @@ xfs_mountfs( /* * Complete the quota initialisation, post-log-replay component. */ - error = XFS_QM_MOUNT(mp, quotamount, quotaflags, mfsi_flags); + error = XFS_QM_MOUNT(mp, quotamount, quotaflags); if (error) goto error4; diff --git a/fs/xfs/xfs_mount.h b/fs/xfs/xfs_mount.h index 5269bd6e3df..02c16b9ce2a 100644 --- a/fs/xfs/xfs_mount.h +++ b/fs/xfs/xfs_mount.h @@ -114,7 +114,7 @@ struct xfs_dqtrxops; struct xfs_quotainfo; typedef int (*xfs_qminit_t)(struct xfs_mount *, uint *, uint *); -typedef int (*xfs_qmmount_t)(struct xfs_mount *, uint, uint, int); +typedef int (*xfs_qmmount_t)(struct xfs_mount *, uint, uint); typedef int (*xfs_qmunmount_t)(struct xfs_mount *); typedef void (*xfs_qmdone_t)(struct xfs_mount *); typedef void (*xfs_dqrele_t)(struct xfs_dquot *); @@ -158,8 +158,8 @@ typedef struct xfs_qmops { #define XFS_QM_INIT(mp, mnt, fl) \ (*(mp)->m_qm_ops->xfs_qminit)(mp, mnt, fl) -#define XFS_QM_MOUNT(mp, mnt, fl, mfsi_flags) \ - (*(mp)->m_qm_ops->xfs_qmmount)(mp, mnt, fl, mfsi_flags) +#define XFS_QM_MOUNT(mp, mnt, fl) \ + (*(mp)->m_qm_ops->xfs_qmmount)(mp, mnt, fl) #define XFS_QM_UNMOUNT(mp) \ (*(mp)->m_qm_ops->xfs_qmunmount)(mp) #define XFS_QM_DONE(mp) \ @@ -442,13 +442,6 @@ void xfs_do_force_shutdown(struct xfs_mount *mp, int flags, char *fname, /* * Flags for xfs_mountfs */ -#define XFS_MFSI_SECOND 0x01 /* Secondary mount -- skip stuff */ -#define XFS_MFSI_CLIENT 0x02 /* Is a client -- skip lots of stuff */ -/* XFS_MFSI_RRINODES */ -#define XFS_MFSI_NOUNLINK 0x08 /* Skip unlinked inode processing in */ - /* log recovery */ -#define XFS_MFSI_NO_QUOTACHECK 0x10 /* Skip quotacheck processing */ -/* XFS_MFSI_CONVERT_SUNIT */ #define XFS_MFSI_QUIET 0x40 /* Be silent if mount errors found */ #define XFS_DADDR_TO_AGNO(mp,d) xfs_daddr_to_agno(mp,d) @@ -517,7 +510,7 @@ typedef struct xfs_mod_sb { extern void xfs_mod_sb(xfs_trans_t *, __int64_t); extern int xfs_log_sbcount(xfs_mount_t *, uint); -extern int xfs_mountfs(xfs_mount_t *mp, int); +extern int xfs_mountfs(xfs_mount_t *mp); extern void xfs_mountfs_check_barriers(xfs_mount_t *mp); extern int xfs_unmountfs(xfs_mount_t *); -- GitLab From 41b5c2e77a0221cf07ac127afa122add67ac5418 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:49:57 +1000 Subject: [PATCH 175/750] [XFS] xfs_unmountfs should return void xfs_unmounts can't and shouldn't return errors so declare it as returning void. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31833a Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/xfs_mount.c | 12 +++++------- fs/xfs/xfs_mount.h | 2 +- 2 files changed, 6 insertions(+), 8 deletions(-) diff --git a/fs/xfs/xfs_mount.c b/fs/xfs/xfs_mount.c index 06f0a73bc93..7f5027266ea 100644 --- a/fs/xfs/xfs_mount.c +++ b/fs/xfs/xfs_mount.c @@ -1229,16 +1229,15 @@ xfs_mountfs( } /* - * xfs_unmountfs - * * This flushes out the inodes,dquots and the superblock, unmounts the * log and makes sure that incore structures are freed. */ -int -xfs_unmountfs(xfs_mount_t *mp) +void +xfs_unmountfs( + struct xfs_mount *mp) { - __uint64_t resblks; - int error = 0; + __uint64_t resblks; + int error; IRELE(mp->m_rootip); @@ -1311,7 +1310,6 @@ xfs_unmountfs(xfs_mount_t *mp) xfs_errortag_clearall(mp, 0); #endif xfs_mount_free(mp); - return 0; } STATIC void diff --git a/fs/xfs/xfs_mount.h b/fs/xfs/xfs_mount.h index 02c16b9ce2a..f3c1024b124 100644 --- a/fs/xfs/xfs_mount.h +++ b/fs/xfs/xfs_mount.h @@ -513,7 +513,7 @@ extern int xfs_log_sbcount(xfs_mount_t *, uint); extern int xfs_mountfs(xfs_mount_t *mp); extern void xfs_mountfs_check_barriers(xfs_mount_t *mp); -extern int xfs_unmountfs(xfs_mount_t *); +extern void xfs_unmountfs(xfs_mount_t *); extern int xfs_unmountfs_writesb(xfs_mount_t *); extern int xfs_unmount_flush(xfs_mount_t *, int); extern int xfs_mod_incore_sb(xfs_mount_t *, xfs_sb_field_t, int64_t, int); -- GitLab From 6203300e5e9121440b27d3ed0b9fe2a64cb62b53 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:50:21 +1000 Subject: [PATCH 176/750] [XFS] don't call xfs_freesb from xfs_unmountfs xfs_readsb is called before xfs_mount so xfs_freesb should be called after xfs_unmountfs, too. This means it now happens after a few things during the of xfs_unmount which all have nothing to do with the superblock. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31835a Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/linux-2.6/xfs_super.c | 3 ++- fs/xfs/xfs_mount.c | 2 -- 2 files changed, 2 insertions(+), 3 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_super.c b/fs/xfs/linux-2.6/xfs_super.c index 8fdb79046a6..73c65f19e54 100644 --- a/fs/xfs/linux-2.6/xfs_super.c +++ b/fs/xfs/linux-2.6/xfs_super.c @@ -1147,6 +1147,7 @@ xfs_fs_put_super( } xfs_unmountfs(mp); + xfs_freesb(mp); xfs_icsb_destroy_counters(mp); xfs_close_devices(mp); xfs_qmops_put(mp); @@ -1803,7 +1804,7 @@ xfs_fs_fill_super( WARN_ON(error); xfs_unmountfs(mp); - goto out_free_fsname; + goto out_free_sb; } STATIC int diff --git a/fs/xfs/xfs_mount.c b/fs/xfs/xfs_mount.c index 7f5027266ea..4d416159840 100644 --- a/fs/xfs/xfs_mount.c +++ b/fs/xfs/xfs_mount.c @@ -1296,8 +1296,6 @@ xfs_unmountfs( xfs_unmountfs_wait(mp); /* wait for async bufs */ xfs_log_unmount(mp); /* Done! No more fs ops. */ - xfs_freesb(mp); - /* * All inodes from this mount point should be freed. */ -- GitLab From ff4f038c6bbb27044a84adbcd27bc237d7237e66 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:50:47 +1000 Subject: [PATCH 177/750] [XFS] refactor xfs_mount_free xfs_mount_free mostly frees the perag data, which is something that is duplicated in the mount error path. Move the XFS_QM_DONE call to the caller and remove the useless mutex_destroy/spinlock_destroy calls so that we can re-use it for the mount error path. Also rename it to xfs_free_perag to reflect what it does. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31836a Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/xfs_mount.c | 21 +++++---------------- 1 file changed, 5 insertions(+), 16 deletions(-) diff --git a/fs/xfs/xfs_mount.c b/fs/xfs/xfs_mount.c index 4d416159840..081fb6a02ac 100644 --- a/fs/xfs/xfs_mount.c +++ b/fs/xfs/xfs_mount.c @@ -128,7 +128,7 @@ static const struct { * initialized. */ STATIC void -xfs_mount_free( +xfs_free_perag( xfs_mount_t *mp) { if (mp->m_perag) { @@ -139,13 +139,6 @@ xfs_mount_free( kmem_free(mp->m_perag[agno].pagb_list); kmem_free(mp->m_perag); } - - spinlock_destroy(&mp->m_ail_lock); - spinlock_destroy(&mp->m_sb_lock); - mutex_destroy(&mp->m_ilock); - mutex_destroy(&mp->m_growlock); - if (mp->m_quotainfo) - XFS_QM_DONE(mp); } /* @@ -922,7 +915,6 @@ xfs_mountfs( __uint64_t resblks; __int64_t update_flags = 0LL; uint quotamount, quotaflags; - int agno; int uuid_mounted = 0; int error = 0; @@ -1216,12 +1208,7 @@ xfs_mountfs( error3: xfs_log_unmount_dealloc(mp); error2: - for (agno = 0; agno < sbp->sb_agcount; agno++) - if (mp->m_perag[agno].pagb_list) - kmem_free(mp->m_perag[agno].pagb_list); - kmem_free(mp->m_perag); - mp->m_perag = NULL; - /* FALLTHROUGH */ + xfs_free_perag(mp); error1: if (uuid_mounted) uuid_table_remove(&mp->m_sb.sb_uuid); @@ -1307,7 +1294,9 @@ xfs_unmountfs( #if defined(DEBUG) xfs_errortag_clearall(mp, 0); #endif - xfs_mount_free(mp); + xfs_free_perag(mp); + if (mp->m_quotainfo) + XFS_QM_DONE(mp); } STATIC void -- GitLab From d62c251fe4a06144255291cffd68cbadf3bf002f Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 13 Aug 2008 16:51:29 +1000 Subject: [PATCH 178/750] [XFS] use KM_MAYFAIL in xfs_mountfs Use KM_MAYFAIL for the m_perag allocation, we can deal with the error easily and blocking forever during mount is not a good idea either. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31837a Signed-off-by: Christoph Hellwig Signed-off-by: Lachlan McIlroy --- fs/xfs/xfs_mount.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/fs/xfs/xfs_mount.c b/fs/xfs/xfs_mount.c index 081fb6a02ac..a4503f5e949 100644 --- a/fs/xfs/xfs_mount.c +++ b/fs/xfs/xfs_mount.c @@ -1052,8 +1052,10 @@ xfs_mountfs( * Allocate and initialize the per-ag data. */ init_rwsem(&mp->m_peraglock); - mp->m_perag = - kmem_zalloc(sbp->sb_agcount * sizeof(xfs_perag_t), KM_SLEEP); + mp->m_perag = kmem_zalloc(sbp->sb_agcount * sizeof(xfs_perag_t), + KM_MAYFAIL); + if (!mp->m_perag) + goto error1; mp->m_maxagi = xfs_initialize_perag(mp, sbp->sb_agcount); -- GitLab From 5695ef46ef02ba1c6658daa46e6879a2d4f52f5f Mon Sep 17 00:00:00 2001 From: Lachlan McIlroy Date: Wed, 13 Aug 2008 16:51:57 +1000 Subject: [PATCH 179/750] [XFS] Use KM_NOFS for debug trace buffers Use KM_NOFS to prevent recursion back into the filesystem which can cause deadlocks. In the case of xfs_iread() we hold the lock on the inode cluster buffer while allocating memory for the trace buffers. If we recurse back into XFS to flush data that may require a transaction to allocate extents which needs log space. This can deadlock with the xfsaild thread which can't push the tail of the log because it is trying to get the inode cluster buffer lock. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31838a Signed-off-by: Lachlan McIlroy Signed-off-by: David Chinner --- fs/xfs/linux-2.6/xfs_buf.c | 2 +- fs/xfs/quota/xfs_dquot.c | 2 +- fs/xfs/xfs_buf_item.c | 2 +- fs/xfs/xfs_filestream.c | 2 +- fs/xfs/xfs_inode.c | 12 ++++++------ fs/xfs/xfs_log.c | 2 +- 6 files changed, 11 insertions(+), 11 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_buf.c b/fs/xfs/linux-2.6/xfs_buf.c index a0072d9315a..986061ae1b9 100644 --- a/fs/xfs/linux-2.6/xfs_buf.c +++ b/fs/xfs/linux-2.6/xfs_buf.c @@ -1795,7 +1795,7 @@ int __init xfs_buf_init(void) { #ifdef XFS_BUF_TRACE - xfs_buf_trace_buf = ktrace_alloc(XFS_BUF_TRACE_SIZE, KM_SLEEP); + xfs_buf_trace_buf = ktrace_alloc(XFS_BUF_TRACE_SIZE, KM_NOFS); #endif xfs_buf_zone = kmem_zone_init_flags(sizeof(xfs_buf_t), "xfs_buf", diff --git a/fs/xfs/quota/xfs_dquot.c b/fs/xfs/quota/xfs_dquot.c index 32290578c66..f2705f2fd43 100644 --- a/fs/xfs/quota/xfs_dquot.c +++ b/fs/xfs/quota/xfs_dquot.c @@ -112,7 +112,7 @@ xfs_qm_dqinit( complete(&dqp->q_flush); #ifdef XFS_DQUOT_TRACE - dqp->q_trace = ktrace_alloc(DQUOT_TRACE_SIZE, KM_SLEEP); + dqp->q_trace = ktrace_alloc(DQUOT_TRACE_SIZE, KM_NOFS); xfs_dqtrace_entry(dqp, "DQINIT"); #endif } else { diff --git a/fs/xfs/xfs_buf_item.c b/fs/xfs/xfs_buf_item.c index 215c36dee32..608c30c3f76 100644 --- a/fs/xfs/xfs_buf_item.c +++ b/fs/xfs/xfs_buf_item.c @@ -737,7 +737,7 @@ xfs_buf_item_init( bip->bli_format.blf_len = (ushort)BTOBB(XFS_BUF_COUNT(bp)); bip->bli_format.blf_map_size = map_size; #ifdef XFS_BLI_TRACE - bip->bli_trace = ktrace_alloc(XFS_BLI_TRACE_SIZE, KM_SLEEP); + bip->bli_trace = ktrace_alloc(XFS_BLI_TRACE_SIZE, KM_NOFS); #endif #ifdef XFS_TRANS_DEBUG diff --git a/fs/xfs/xfs_filestream.c b/fs/xfs/xfs_filestream.c index c38fd14fca2..f3bb75da384 100644 --- a/fs/xfs/xfs_filestream.c +++ b/fs/xfs/xfs_filestream.c @@ -400,7 +400,7 @@ xfs_filestream_init(void) if (!item_zone) return -ENOMEM; #ifdef XFS_FILESTREAMS_TRACE - xfs_filestreams_trace_buf = ktrace_alloc(XFS_FSTRM_KTRACE_SIZE, KM_SLEEP); + xfs_filestreams_trace_buf = ktrace_alloc(XFS_FSTRM_KTRACE_SIZE, KM_NOFS); #endif return 0; } diff --git a/fs/xfs/xfs_inode.c b/fs/xfs/xfs_inode.c index 41371c56f36..358511b85ce 100644 --- a/fs/xfs/xfs_inode.c +++ b/fs/xfs/xfs_inode.c @@ -835,22 +835,22 @@ xfs_iread( * Do this before xfs_iformat in case it adds entries. */ #ifdef XFS_INODE_TRACE - ip->i_trace = ktrace_alloc(INODE_TRACE_SIZE, KM_SLEEP); + ip->i_trace = ktrace_alloc(INODE_TRACE_SIZE, KM_NOFS); #endif #ifdef XFS_BMAP_TRACE - ip->i_xtrace = ktrace_alloc(XFS_BMAP_KTRACE_SIZE, KM_SLEEP); + ip->i_xtrace = ktrace_alloc(XFS_BMAP_KTRACE_SIZE, KM_NOFS); #endif #ifdef XFS_BMBT_TRACE - ip->i_btrace = ktrace_alloc(XFS_BMBT_KTRACE_SIZE, KM_SLEEP); + ip->i_btrace = ktrace_alloc(XFS_BMBT_KTRACE_SIZE, KM_NOFS); #endif #ifdef XFS_RW_TRACE - ip->i_rwtrace = ktrace_alloc(XFS_RW_KTRACE_SIZE, KM_SLEEP); + ip->i_rwtrace = ktrace_alloc(XFS_RW_KTRACE_SIZE, KM_NOFS); #endif #ifdef XFS_ILOCK_TRACE - ip->i_lock_trace = ktrace_alloc(XFS_ILOCK_KTRACE_SIZE, KM_SLEEP); + ip->i_lock_trace = ktrace_alloc(XFS_ILOCK_KTRACE_SIZE, KM_NOFS); #endif #ifdef XFS_DIR2_TRACE - ip->i_dir_trace = ktrace_alloc(XFS_DIR2_KTRACE_SIZE, KM_SLEEP); + ip->i_dir_trace = ktrace_alloc(XFS_DIR2_KTRACE_SIZE, KM_NOFS); #endif /* diff --git a/fs/xfs/xfs_log.c b/fs/xfs/xfs_log.c index 9c23864d4fd..1f6f780dbd3 100644 --- a/fs/xfs/xfs_log.c +++ b/fs/xfs/xfs_log.c @@ -160,7 +160,7 @@ void xlog_trace_iclog(xlog_in_core_t *iclog, uint state) { if (!iclog->ic_trace) - iclog->ic_trace = ktrace_alloc(256, KM_SLEEP); + iclog->ic_trace = ktrace_alloc(256, KM_NOFS); ktrace_enter(iclog->ic_trace, (void *)((unsigned long)state), (void *)((unsigned long)current_pid()), -- GitLab From c94312de223644e2f18e7064ae8cafa14e5c6ef6 Mon Sep 17 00:00:00 2001 From: Ruben Porras Date: Wed, 13 Aug 2008 16:52:25 +1000 Subject: [PATCH 180/750] [XFS] Make xfs_bmap_*_count_leaves void. xfs_bmap_count_leaves and xfs_bmap_disk_count_leaves always return always 0, make them void. SGI-PV: 981498 SGI-Modid: xfs-linux-melb:xfs-kern:31844a Signed-off-by: Ruben Porras Signed-off-by: Donald Douwsma Signed-off-by: Lachlan McIlroy --- fs/xfs/xfs_bmap.c | 26 +++++++------------------- 1 file changed, 7 insertions(+), 19 deletions(-) diff --git a/fs/xfs/xfs_bmap.c b/fs/xfs/xfs_bmap.c index 3d6a2ce8503..a1aab9275d5 100644 --- a/fs/xfs/xfs_bmap.c +++ b/fs/xfs/xfs_bmap.c @@ -384,14 +384,14 @@ xfs_bmap_count_tree( int levelin, int *count); -STATIC int +STATIC void xfs_bmap_count_leaves( xfs_ifork_t *ifp, xfs_extnum_t idx, int numrecs, int *count); -STATIC int +STATIC void xfs_bmap_disk_count_leaves( xfs_extnum_t idx, xfs_bmbt_block_t *block, @@ -6367,13 +6367,9 @@ xfs_bmap_count_blocks( mp = ip->i_mount; ifp = XFS_IFORK_PTR(ip, whichfork); if ( XFS_IFORK_FORMAT(ip, whichfork) == XFS_DINODE_FMT_EXTENTS ) { - if (unlikely(xfs_bmap_count_leaves(ifp, 0, + xfs_bmap_count_leaves(ifp, 0, ifp->if_bytes / (uint)sizeof(xfs_bmbt_rec_t), - count) < 0)) { - XFS_ERROR_REPORT("xfs_bmap_count_blocks(1)", - XFS_ERRLEVEL_LOW, mp); - return XFS_ERROR(EFSCORRUPTED); - } + count); return 0; } @@ -6454,13 +6450,7 @@ xfs_bmap_count_tree( for (;;) { nextbno = be64_to_cpu(block->bb_rightsib); numrecs = be16_to_cpu(block->bb_numrecs); - if (unlikely(xfs_bmap_disk_count_leaves(0, - block, numrecs, count) < 0)) { - xfs_trans_brelse(tp, bp); - XFS_ERROR_REPORT("xfs_bmap_count_tree(2)", - XFS_ERRLEVEL_LOW, mp); - return XFS_ERROR(EFSCORRUPTED); - } + xfs_bmap_disk_count_leaves(0, block, numrecs, count); xfs_trans_brelse(tp, bp); if (nextbno == NULLFSBLOCK) break; @@ -6478,7 +6468,7 @@ xfs_bmap_count_tree( /* * Count leaf blocks given a range of extent records. */ -STATIC int +STATIC void xfs_bmap_count_leaves( xfs_ifork_t *ifp, xfs_extnum_t idx, @@ -6491,14 +6481,13 @@ xfs_bmap_count_leaves( xfs_bmbt_rec_host_t *frp = xfs_iext_get_ext(ifp, idx + b); *count += xfs_bmbt_get_blockcount(frp); } - return 0; } /* * Count leaf blocks given a range of extent records originally * in btree format. */ -STATIC int +STATIC void xfs_bmap_disk_count_leaves( xfs_extnum_t idx, xfs_bmbt_block_t *block, @@ -6512,5 +6501,4 @@ xfs_bmap_disk_count_leaves( frp = XFS_BTREE_REC_ADDR(xfs_bmbt, block, idx + b); *count += xfs_bmbt_disk_get_blockcount(frp); } - return 0; } -- GitLab From c6a7b0f8a49aa71792dd108efc535435f462bf79 Mon Sep 17 00:00:00 2001 From: Lachlan McIlroy Date: Wed, 13 Aug 2008 16:52:50 +1000 Subject: [PATCH 181/750] [XFS] Fix use after free in xfs_log_done(). The ticket allocation code got reworked in 2.6.26 and we now free tickets whereas before we used to cache them so the use-after-free went undetected. SGI-PV: 985525 SGI-Modid: xfs-linux-melb:xfs-kern:31877a Signed-off-by: Lachlan McIlroy Signed-off-by: David Chinner --- fs/xfs/xfs_log.c | 13 +++++-------- 1 file changed, 5 insertions(+), 8 deletions(-) diff --git a/fs/xfs/xfs_log.c b/fs/xfs/xfs_log.c index 1f6f780dbd3..ccba14eb9db 100644 --- a/fs/xfs/xfs_log.c +++ b/fs/xfs/xfs_log.c @@ -336,15 +336,12 @@ xfs_log_done(xfs_mount_t *mp, } else { xlog_trace_loggrant(log, ticket, "xfs_log_done: (permanent)"); xlog_regrant_reserve_log_space(log, ticket); - } - - /* If this ticket was a permanent reservation and we aren't - * trying to release it, reset the inited flags; so next time - * we write, a start record will be written out. - */ - if ((ticket->t_flags & XLOG_TIC_PERM_RESERV) && - (flags & XFS_LOG_REL_PERM_RESERV) == 0) + /* If this ticket was a permanent reservation and we aren't + * trying to release it, reset the inited flags; so next time + * we write, a start record will be written out. + */ ticket->t_flags |= XLOG_TIC_INITED; + } return lsn; } /* xfs_log_done */ -- GitLab From 2e244d08369b510923fe8290d40d51b0e88bfebe Mon Sep 17 00:00:00 2001 From: Sebastian Siewior Date: Thu, 17 Jul 2008 14:16:09 +0200 Subject: [PATCH 182/750] Documentation: fix typo in ubifs.txt Signed-off-by: Sebastian Siewior Signed-off-by: Artem Bityutskiy --- Documentation/filesystems/ubifs.txt | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Documentation/filesystems/ubifs.txt b/Documentation/filesystems/ubifs.txt index 540e9e7f59c..6a0d70a22f0 100644 --- a/Documentation/filesystems/ubifs.txt +++ b/Documentation/filesystems/ubifs.txt @@ -57,7 +57,7 @@ Similarly to JFFS2, UBIFS supports on-the-flight compression which makes it possible to fit quite a lot of data to the flash. Similarly to JFFS2, UBIFS is tolerant of unclean reboots and power-cuts. -It does not need stuff like ckfs.ext2. UBIFS automatically replays its +It does not need stuff like fsck.ext2. UBIFS automatically replays its journal and recovers from crashes, ensuring that the on-flash data structures are consistent. -- GitLab From ce769caa50a3fc835b4fc1a6e1463ada127a2e8a Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Fri, 18 Jul 2008 12:54:21 +0300 Subject: [PATCH 183/750] UBIFS: print volume name as well We encouredge people to mount using volume name, not device numbers. So print the name of the mounted UBI volume, not just IDs. Signed-off-by: Artem Bityutskiy --- fs/ubifs/super.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/fs/ubifs/super.c b/fs/ubifs/super.c index ca1e2d4e03c..43af934a755 100644 --- a/fs/ubifs/super.c +++ b/fs/ubifs/super.c @@ -1122,8 +1122,8 @@ static int mount_ubifs(struct ubifs_info *c) if (err) goto out_infos; - ubifs_msg("mounted UBI device %d, volume %d", c->vi.ubi_num, - c->vi.vol_id); + ubifs_msg("mounted UBI device %d, volume %d, name \"%s\"", + c->vi.ubi_num, c->vi.vol_id, c->vi.name); if (mounted_read_only) ubifs_msg("mounted read-only"); x = (long long)c->main_lebs * c->leb_size; -- GitLab From 182854b46f9feb6f1b03abe747bb2beeebf2adb0 Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Fri, 18 Jul 2008 18:54:29 +0300 Subject: [PATCH 184/750] UBIFS: fix budgeting calculations The 'ubifs_release_dirty_inode_budget()' was buggy and incorrectly freed the budget, which led to not freeing all dirty data budget. This patch fixes that. Also, this patch fixes ubifs_mkdir() which passed 1 in dirty_ino_d, which makes no sense. Well, it is harmless though. Also, add few more useful assertions. And improve few debugging messages. Signed-off-by: Artem Bityutskiy --- fs/ubifs/budget.c | 5 +++-- fs/ubifs/dir.c | 3 +-- 2 files changed, 4 insertions(+), 4 deletions(-) diff --git a/fs/ubifs/budget.c b/fs/ubifs/budget.c index d81fb9ed2b8..12a1717db87 100644 --- a/fs/ubifs/budget.c +++ b/fs/ubifs/budget.c @@ -686,9 +686,10 @@ void ubifs_convert_page_budget(struct ubifs_info *c) void ubifs_release_dirty_inode_budget(struct ubifs_info *c, struct ubifs_inode *ui) { - struct ubifs_budget_req req = {.dd_growth = c->inode_budget, - .dirtied_ino_d = ui->data_len}; + struct ubifs_budget_req req; + memset(&req, 0, sizeof(struct ubifs_budget_req)); + req.dd_growth = c->inode_budget + ui->data_len; ubifs_release_budget(c, &req); } diff --git a/fs/ubifs/dir.c b/fs/ubifs/dir.c index e90374be7d3..a79e850fee6 100644 --- a/fs/ubifs/dir.c +++ b/fs/ubifs/dir.c @@ -727,8 +727,7 @@ static int ubifs_mkdir(struct inode *dir, struct dentry *dentry, int mode) struct ubifs_inode *dir_ui = ubifs_inode(dir); struct ubifs_info *c = dir->i_sb->s_fs_info; int err, sz_change = CALC_DENT_SIZE(dentry->d_name.len); - struct ubifs_budget_req req = { .new_ino = 1, .new_dent = 1, - .dirtied_ino_d = 1 }; + struct ubifs_budget_req req = { .new_ino = 1, .new_dent = 1 }; /* * Budget request settings: new inode, new direntry and changing parent -- GitLab From 7d32c2bb143fa1ca3b0c420feb08a832d65395be Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Fri, 18 Jul 2008 18:54:29 +0300 Subject: [PATCH 185/750] UBIFS: improve debugging 1. Print inode mode in some of debugging messages 2. Add few more useful assertions Signed-off-by: Artem Bityutskiy --- fs/ubifs/file.c | 3 ++- fs/ubifs/super.c | 6 ++++-- 2 files changed, 6 insertions(+), 3 deletions(-) diff --git a/fs/ubifs/file.c b/fs/ubifs/file.c index 8565e586e53..01598f28020 100644 --- a/fs/ubifs/file.c +++ b/fs/ubifs/file.c @@ -941,7 +941,8 @@ int ubifs_setattr(struct dentry *dentry, struct iattr *attr) struct inode *inode = dentry->d_inode; struct ubifs_info *c = inode->i_sb->s_fs_info; - dbg_gen("ino %lu, ia_valid %#x", inode->i_ino, attr->ia_valid); + dbg_gen("ino %lu, mode %#x, ia_valid %#x", + inode->i_ino, inode->i_mode, attr->ia_valid); err = inode_change_ok(inode, attr); if (err) return err; diff --git a/fs/ubifs/super.c b/fs/ubifs/super.c index 43af934a755..06e3b22a0c1 100644 --- a/fs/ubifs/super.c +++ b/fs/ubifs/super.c @@ -299,7 +299,7 @@ static int ubifs_write_inode(struct inode *inode, int wait) return 0; } - dbg_gen("inode %lu", inode->i_ino); + dbg_gen("inode %lu, mode %#x", inode->i_ino, (int)inode->i_mode); err = ubifs_jnl_write_inode(c, inode, 0); if (err) ubifs_err("can't write inode %lu, error %d", inode->i_ino, err); @@ -323,9 +323,10 @@ static void ubifs_delete_inode(struct inode *inode) */ goto out; - dbg_gen("inode %lu", inode->i_ino); + dbg_gen("inode %lu, mode %#x", inode->i_ino, (int)inode->i_mode); ubifs_assert(!atomic_read(&inode->i_count)); ubifs_assert(inode->i_nlink == 0); + ubifs_assert(!ubifs_inode(inode)->dirty); truncate_inode_pages(&inode->i_data, 0); if (is_bad_inode(inode)) @@ -1469,6 +1470,7 @@ static void ubifs_put_super(struct super_block *sb) */ ubifs_assert(atomic_long_read(&c->dirty_pg_cnt) == 0); ubifs_assert(c->budg_idx_growth == 0); + ubifs_assert(c->budg_dd_growth == 0); ubifs_assert(c->budg_data_growth == 0); /* -- GitLab From 1e0f358e29cc91c8eb09e10cbf1f6bb58a62c795 Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Mon, 21 Jul 2008 10:59:53 +0300 Subject: [PATCH 186/750] UBIFS: free budget in delete_inode as well Although the inode is marked as clean when it is being deleted, it might stay and be used as orphan, and be marked as dirty. So we have to free the budget when we delete it. Signed-off-by: Artem Bityutskiy --- fs/ubifs/super.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) diff --git a/fs/ubifs/super.c b/fs/ubifs/super.c index 06e3b22a0c1..884beed1dcb 100644 --- a/fs/ubifs/super.c +++ b/fs/ubifs/super.c @@ -314,8 +314,9 @@ static void ubifs_delete_inode(struct inode *inode) { int err; struct ubifs_info *c = inode->i_sb->s_fs_info; + struct ubifs_inode *ui = ubifs_inode(inode); - if (ubifs_inode(inode)->xattr) + if (ui->xattr) /* * Extended attribute inode deletions are fully handled in * 'ubifs_removexattr()'. These inodes are special and have @@ -326,13 +327,12 @@ static void ubifs_delete_inode(struct inode *inode) dbg_gen("inode %lu, mode %#x", inode->i_ino, (int)inode->i_mode); ubifs_assert(!atomic_read(&inode->i_count)); ubifs_assert(inode->i_nlink == 0); - ubifs_assert(!ubifs_inode(inode)->dirty); truncate_inode_pages(&inode->i_data, 0); if (is_bad_inode(inode)) goto out; - ubifs_inode(inode)->ui_size = inode->i_size = 0; + ui->ui_size = inode->i_size = 0; err = ubifs_jnl_write_inode(c, inode, 1); if (err) /* @@ -341,6 +341,8 @@ static void ubifs_delete_inode(struct inode *inode) */ ubifs_err("can't write inode %lu, error %d", inode->i_ino, err); out: + if (ui->dirty) + ubifs_release_dirty_inode_budget(c, ui); clear_inode(inode); } -- GitLab From 16dfd804b44ef7156d1c201f100bd0d9dc6b7c4b Mon Sep 17 00:00:00 2001 From: Adrian Hunter Date: Fri, 18 Jul 2008 16:47:41 +0300 Subject: [PATCH 187/750] UBIFS: fix error return in failure mode UBIFS recovery testing debug facility simulates media failures. When simulating an IO error, the error code returned must be -EIO but it was not always if the user switched off the debug recovery testing option at the same time. Signed-off-by: Adrian Hunter --- fs/ubifs/debug.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/fs/ubifs/debug.c b/fs/ubifs/debug.c index 4e3aaeba4ec..0adfb29b850 100644 --- a/fs/ubifs/debug.c +++ b/fs/ubifs/debug.c @@ -2208,16 +2208,17 @@ int dbg_leb_read(struct ubi_volume_desc *desc, int lnum, char *buf, int offset, int dbg_leb_write(struct ubi_volume_desc *desc, int lnum, const void *buf, int offset, int len, int dtype) { - int err; + int err, failing; if (in_failure_mode(desc)) return -EIO; - if (do_fail(desc, lnum, 1)) + failing = do_fail(desc, lnum, 1); + if (failing) cut_data(buf, len); err = ubi_leb_write(desc, lnum, buf, offset, len, dtype); if (err) return err; - if (in_failure_mode(desc)) + if (failing) return -EIO; return 0; } -- GitLab From 2fb42b11f61cbcef7dfc225c1d26c4511436583d Mon Sep 17 00:00:00 2001 From: Adrian Hunter Date: Fri, 18 Jul 2008 17:56:37 +0300 Subject: [PATCH 188/750] UBIFS: ensure UBIFS switches to read-only on error UBI transparently handles write errors by automatically copying and remapping the affected eraseblock. If UBI is unable to do that, for example its pool of eraseblocks reserved for bad block handling is empty, then the error is propagated to UBIFS. UBIFS must protect the media from falling into an inconsistent state by immediately switching to read-only mode. In the case of log updates, this was not being done. Signed-off-by: Adrian Hunter --- fs/ubifs/log.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/fs/ubifs/log.c b/fs/ubifs/log.c index 36857b9ed59..e14829e5069 100644 --- a/fs/ubifs/log.c +++ b/fs/ubifs/log.c @@ -317,6 +317,8 @@ int ubifs_add_bud_to_log(struct ubifs_info *c, int jhead, int lnum, int offs) return 0; out_unlock: + if (err != -EAGAIN) + ubifs_ro_mode(c, err); mutex_unlock(&c->log_mutex); kfree(ref); kfree(bud); -- GitLab From ff46d7b3e0870a70331b069372c36fbc43018c2d Mon Sep 17 00:00:00 2001 From: Adrian Hunter Date: Mon, 21 Jul 2008 15:39:05 +0300 Subject: [PATCH 189/750] UBIFS: make ubifs_ro_mode() not inline We use ubifs_ro_mode() quite a lot, and not in fast-path, so there is no reason to blow the code up by having it inlined. Also, we usually want R/O mode change to be seen to other CPUs as soon as possible, so when we make this a function call, we will automatically have a memory barrier. Signed-off-by: Adrian Hunter Signed-off-by: Artem Bityutskiy --- fs/ubifs/io.c | 14 ++++++++++++++ fs/ubifs/misc.h | 14 -------------- fs/ubifs/ubifs.h | 1 + 3 files changed, 15 insertions(+), 14 deletions(-) diff --git a/fs/ubifs/io.c b/fs/ubifs/io.c index 3374f91b670..054363f2b20 100644 --- a/fs/ubifs/io.c +++ b/fs/ubifs/io.c @@ -53,6 +53,20 @@ #include #include "ubifs.h" +/** + * ubifs_ro_mode - switch UBIFS to read read-only mode. + * @c: UBIFS file-system description object + * @err: error code which is the reason of switching to R/O mode + */ +void ubifs_ro_mode(struct ubifs_info *c, int err) +{ + if (!c->ro_media) { + c->ro_media = 1; + ubifs_warn("switched to read-only mode, error %d", err); + dbg_dump_stack(); + } +} + /** * ubifs_check_node - check node. * @c: UBIFS file-system description object diff --git a/fs/ubifs/misc.h b/fs/ubifs/misc.h index 4beccfc256d..cd83ffc8101 100644 --- a/fs/ubifs/misc.h +++ b/fs/ubifs/misc.h @@ -79,20 +79,6 @@ static inline struct ubifs_inode *ubifs_inode(const struct inode *inode) return container_of(inode, struct ubifs_inode, vfs_inode); } -/** - * ubifs_ro_mode - switch UBIFS to read read-only mode. - * @c: UBIFS file-system description object - * @err: error code which is the reason of switching to R/O mode - */ -static inline void ubifs_ro_mode(struct ubifs_info *c, int err) -{ - if (!c->ro_media) { - c->ro_media = 1; - ubifs_warn("switched to read-only mode, error %d", err); - dbg_dump_stack(); - } -} - /** * ubifs_compr_present - check if compressor was compiled in. * @compr_type: compressor type to check diff --git a/fs/ubifs/ubifs.h b/fs/ubifs/ubifs.h index e4f89f27182..c488d43b635 100644 --- a/fs/ubifs/ubifs.h +++ b/fs/ubifs/ubifs.h @@ -1346,6 +1346,7 @@ extern struct backing_dev_info ubifs_backing_dev_info; extern struct ubifs_compressor *ubifs_compressors[UBIFS_COMPR_TYPES_CNT]; /* io.c */ +void ubifs_ro_mode(struct ubifs_info *c, int err); int ubifs_wbuf_write_nolock(struct ubifs_wbuf *wbuf, void *buf, int len); int ubifs_wbuf_seek_nolock(struct ubifs_wbuf *wbuf, int lnum, int offs, int dtype); -- GitLab From fbfa6c884aae2aff479eb8c996c564b1a34eae30 Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Tue, 22 Jul 2008 11:52:52 +0300 Subject: [PATCH 190/750] UBIFS: do not write orphans back Orphan inodes are deleted inodes which will disappear after FS re-mount. There is not need to write orphan inodes back, because they are not needed on the flash media. So optimize orphans a little by not writing them back. Just mark them as clean, free the budget, and report success to VFS. Signed-off-by: Artem Bityutskiy --- fs/ubifs/super.c | 18 +++++++++++++----- 1 file changed, 13 insertions(+), 5 deletions(-) diff --git a/fs/ubifs/super.c b/fs/ubifs/super.c index 884beed1dcb..13e90b0dd95 100644 --- a/fs/ubifs/super.c +++ b/fs/ubifs/super.c @@ -278,7 +278,7 @@ static void ubifs_destroy_inode(struct inode *inode) */ static int ubifs_write_inode(struct inode *inode, int wait) { - int err; + int err = 0; struct ubifs_info *c = inode->i_sb->s_fs_info; struct ubifs_inode *ui = ubifs_inode(inode); @@ -299,10 +299,18 @@ static int ubifs_write_inode(struct inode *inode, int wait) return 0; } - dbg_gen("inode %lu, mode %#x", inode->i_ino, (int)inode->i_mode); - err = ubifs_jnl_write_inode(c, inode, 0); - if (err) - ubifs_err("can't write inode %lu, error %d", inode->i_ino, err); + /* + * As an optimization, do not write orphan inodes to the media just + * because this is not needed. + */ + dbg_gen("inode %lu, mode %#x, nlink %u", + inode->i_ino, (int)inode->i_mode, inode->i_nlink); + if (inode->i_nlink) { + err = ubifs_jnl_write_inode(c, inode, 0); + if (err) + ubifs_err("can't write inode %lu, error %d", + inode->i_ino, err); + } ui->dirty = 0; mutex_unlock(&ui->ui_mutex); -- GitLab From 1f28681ad34a0c7e51dc5070c84b53f7bd34f44c Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Tue, 22 Jul 2008 12:06:13 +0300 Subject: [PATCH 191/750] UBIFS: remove unneeded function parameter Simplify 'ubifs_jnl_write_inode()' by removing the 'deletion' parameter which is not really needed because we may test inode->i_nlink and check whether this is a deletion or not. Signed-off-by: Artem Bityutskiy --- fs/ubifs/journal.c | 19 +++++++------------ fs/ubifs/super.c | 4 ++-- fs/ubifs/ubifs.h | 3 +-- 3 files changed, 10 insertions(+), 16 deletions(-) diff --git a/fs/ubifs/journal.c b/fs/ubifs/journal.c index 283155abe5f..666ad82ec51 100644 --- a/fs/ubifs/journal.c +++ b/fs/ubifs/journal.c @@ -750,30 +750,25 @@ out_free: * ubifs_jnl_write_inode - flush inode to the journal. * @c: UBIFS file-system description object * @inode: inode to flush - * @deletion: inode has been deleted * * This function writes inode @inode to the journal. If the inode is * synchronous, it also synchronizes the write-buffer. Returns zero in case of * success and a negative error code in case of failure. */ -int ubifs_jnl_write_inode(struct ubifs_info *c, const struct inode *inode, - int deletion) +int ubifs_jnl_write_inode(struct ubifs_info *c, const struct inode *inode) { - int err, len, lnum, offs, sync = 0; + int err, lnum, offs; struct ubifs_ino_node *ino; struct ubifs_inode *ui = ubifs_inode(inode); + int sync = 0, len = UBIFS_INO_NODE_SZ, last_reference = !inode->i_nlink; - dbg_jnl("ino %lu%s", inode->i_ino, - deletion ? " (last reference)" : ""); - if (deletion) - ubifs_assert(inode->i_nlink == 0); + dbg_jnl("ino %lu, nlink %u", inode->i_ino, inode->i_nlink); - len = UBIFS_INO_NODE_SZ; /* * If the inode is being deleted, do not write the attached data. No * need to synchronize the write-buffer either. */ - if (!deletion) { + if (!last_reference) { len += ui->data_len; sync = IS_SYNC(inode); } @@ -786,7 +781,7 @@ int ubifs_jnl_write_inode(struct ubifs_info *c, const struct inode *inode, if (err) goto out_free; - pack_inode(c, ino, inode, 1, deletion); + pack_inode(c, ino, inode, 1, last_reference); err = write_head(c, BASEHD, ino, len, &lnum, &offs, sync); if (err) goto out_release; @@ -795,7 +790,7 @@ int ubifs_jnl_write_inode(struct ubifs_info *c, const struct inode *inode, inode->i_ino); release_head(c, BASEHD); - if (deletion) { + if (last_reference) { err = ubifs_tnc_remove_ino(c, inode->i_ino); if (err) goto out_ro; diff --git a/fs/ubifs/super.c b/fs/ubifs/super.c index 13e90b0dd95..cf1fb6cffa0 100644 --- a/fs/ubifs/super.c +++ b/fs/ubifs/super.c @@ -306,7 +306,7 @@ static int ubifs_write_inode(struct inode *inode, int wait) dbg_gen("inode %lu, mode %#x, nlink %u", inode->i_ino, (int)inode->i_mode, inode->i_nlink); if (inode->i_nlink) { - err = ubifs_jnl_write_inode(c, inode, 0); + err = ubifs_jnl_write_inode(c, inode); if (err) ubifs_err("can't write inode %lu, error %d", inode->i_ino, err); @@ -341,7 +341,7 @@ static void ubifs_delete_inode(struct inode *inode) goto out; ui->ui_size = inode->i_size = 0; - err = ubifs_jnl_write_inode(c, inode, 1); + err = ubifs_jnl_write_inode(c, inode); if (err) /* * Worst case we have a lost orphan inode wasting space, so a diff --git a/fs/ubifs/ubifs.h b/fs/ubifs/ubifs.h index c488d43b635..6ddd1de2ea6 100644 --- a/fs/ubifs/ubifs.h +++ b/fs/ubifs/ubifs.h @@ -1400,8 +1400,7 @@ int ubifs_jnl_update(struct ubifs_info *c, const struct inode *dir, int deletion, int xent); int ubifs_jnl_write_data(struct ubifs_info *c, const struct inode *inode, const union ubifs_key *key, const void *buf, int len); -int ubifs_jnl_write_inode(struct ubifs_info *c, const struct inode *inode, - int last_reference); +int ubifs_jnl_write_inode(struct ubifs_info *c, const struct inode *inode); int ubifs_jnl_rename(struct ubifs_info *c, const struct inode *old_dir, const struct dentry *old_dentry, const struct inode *new_dir, -- GitLab From fd6c6b51e3677937090314b20b00f2194900d81b Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Tue, 22 Jul 2008 12:19:09 +0300 Subject: [PATCH 192/750] UBIFS: remove another unneeded function parameter The 'last_reference' parameter of 'pack_inode()' is not really needed because 'inode->i_nlink' may be tested instead. Zap it. Signed-off-by: Artem Bityutskiy --- fs/ubifs/journal.c | 30 ++++++++++++++---------------- 1 file changed, 14 insertions(+), 16 deletions(-) diff --git a/fs/ubifs/journal.c b/fs/ubifs/journal.c index 666ad82ec51..3bc3fc94709 100644 --- a/fs/ubifs/journal.c +++ b/fs/ubifs/journal.c @@ -447,13 +447,11 @@ static int get_dent_type(int mode) * @ino: buffer in which to pack inode node * @inode: inode to pack * @last: indicates the last node of the group - * @last_reference: non-zero if this is a deletion inode */ static void pack_inode(struct ubifs_info *c, struct ubifs_ino_node *ino, - const struct inode *inode, int last, - int last_reference) + const struct inode *inode, int last) { - int data_len = 0; + int data_len = 0, last_reference = !inode->i_nlink; struct ubifs_inode *ui = ubifs_inode(inode); ino->ch.node_type = UBIFS_INO_NODE; @@ -596,9 +594,9 @@ int ubifs_jnl_update(struct ubifs_info *c, const struct inode *dir, ubifs_prep_grp_node(c, dent, dlen, 0); ino = (void *)dent + aligned_dlen; - pack_inode(c, ino, inode, 0, last_reference); + pack_inode(c, ino, inode, 0); ino = (void *)ino + aligned_ilen; - pack_inode(c, ino, dir, 1, 0); + pack_inode(c, ino, dir, 1); if (last_reference) { err = ubifs_add_orphan(c, inode->i_ino); @@ -781,7 +779,7 @@ int ubifs_jnl_write_inode(struct ubifs_info *c, const struct inode *inode) if (err) goto out_free; - pack_inode(c, ino, inode, 1, last_reference); + pack_inode(c, ino, inode, 1); err = write_head(c, BASEHD, ino, len, &lnum, &offs, sync); if (err) goto out_release; @@ -912,16 +910,16 @@ int ubifs_jnl_rename(struct ubifs_info *c, const struct inode *old_dir, p = (void *)dent2 + aligned_dlen2; if (new_inode) { - pack_inode(c, p, new_inode, 0, last_reference); + pack_inode(c, p, new_inode, 0); p += ALIGN(ilen, 8); } if (!move) - pack_inode(c, p, old_dir, 1, 0); + pack_inode(c, p, old_dir, 1); else { - pack_inode(c, p, old_dir, 0, 0); + pack_inode(c, p, old_dir, 0); p += ALIGN(plen, 8); - pack_inode(c, p, new_dir, 1, 0); + pack_inode(c, p, new_dir, 1); } if (last_reference) { @@ -1126,7 +1124,7 @@ int ubifs_jnl_truncate(struct ubifs_info *c, const struct inode *inode, if (err) goto out_free; - pack_inode(c, ino, inode, 0, 0); + pack_inode(c, ino, inode, 0); ubifs_prep_grp_node(c, trun, UBIFS_TRUN_NODE_SZ, dlen ? 0 : 1); if (dlen) ubifs_prep_grp_node(c, dn, dlen, 1); @@ -1246,9 +1244,9 @@ int ubifs_jnl_delete_xattr(struct ubifs_info *c, const struct inode *host, ubifs_prep_grp_node(c, xent, xlen, 0); ino = (void *)xent + aligned_xlen; - pack_inode(c, ino, inode, 0, 1); + pack_inode(c, ino, inode, 0); ino = (void *)ino + UBIFS_INO_NODE_SZ; - pack_inode(c, ino, host, 1, 0); + pack_inode(c, ino, host, 1); err = write_head(c, BASEHD, xent, len, &lnum, &xent_offs, sync); if (!sync && !err) @@ -1339,8 +1337,8 @@ int ubifs_jnl_change_xattr(struct ubifs_info *c, const struct inode *inode, if (err) goto out_free; - pack_inode(c, ino, host, 0, 0); - pack_inode(c, (void *)ino + aligned_len1, inode, 1, 0); + pack_inode(c, ino, host, 0); + pack_inode(c, (void *)ino + aligned_len1, inode, 1); err = write_head(c, BASEHD, ino, aligned_len, &lnum, &offs, 0); if (!sync && !err) { -- GitLab From 014eb04b03202dc75c1c749df4246d98045f5e69 Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Mon, 21 Jul 2008 17:14:29 +0300 Subject: [PATCH 193/750] UBIFS: increment commit number earlier Increment the commit number at the beginnig of the commit, instead of doing this after the commit. This is needed for further optimizations. Signed-off-by: Artem Bityutskiy --- fs/ubifs/commit.c | 3 ++- fs/ubifs/log.c | 2 +- fs/ubifs/orphan.c | 4 ++-- fs/ubifs/ubifs.h | 3 ++- 4 files changed, 7 insertions(+), 5 deletions(-) diff --git a/fs/ubifs/commit.c b/fs/ubifs/commit.c index 3b516316c9b..0a6aa2cc78f 100644 --- a/fs/ubifs/commit.c +++ b/fs/ubifs/commit.c @@ -74,6 +74,7 @@ static int do_commit(struct ubifs_info *c) goto out_up; } + c->cmt_no += 1; err = ubifs_gc_start_commit(c); if (err) goto out_up; @@ -115,7 +116,7 @@ static int do_commit(struct ubifs_info *c) goto out; mutex_lock(&c->mst_mutex); - c->mst_node->cmt_no = cpu_to_le64(++c->cmt_no); + c->mst_node->cmt_no = cpu_to_le64(c->cmt_no); c->mst_node->log_lnum = cpu_to_le32(new_ltail_lnum); c->mst_node->root_lnum = cpu_to_le32(zroot.lnum); c->mst_node->root_offs = cpu_to_le32(zroot.offs); diff --git a/fs/ubifs/log.c b/fs/ubifs/log.c index e14829e5069..3e0aa736755 100644 --- a/fs/ubifs/log.c +++ b/fs/ubifs/log.c @@ -412,7 +412,7 @@ int ubifs_log_start_commit(struct ubifs_info *c, int *ltail_lnum) return -ENOMEM; cs->ch.node_type = UBIFS_CS_NODE; - cs->cmt_no = cpu_to_le64(c->cmt_no + 1); + cs->cmt_no = cpu_to_le64(c->cmt_no); ubifs_prepare_node(c, cs, UBIFS_CS_NODE_SZ, 0); /* diff --git a/fs/ubifs/orphan.c b/fs/ubifs/orphan.c index 3afeb9242c6..02d3462f4d3 100644 --- a/fs/ubifs/orphan.c +++ b/fs/ubifs/orphan.c @@ -310,10 +310,10 @@ static int write_orph_node(struct ubifs_info *c, int atomic) c->cmt_orphans -= cnt; spin_unlock(&c->orphan_lock); if (c->cmt_orphans) - orph->cmt_no = cpu_to_le64(c->cmt_no + 1); + orph->cmt_no = cpu_to_le64(c->cmt_no); else /* Mark the last node of the commit */ - orph->cmt_no = cpu_to_le64((c->cmt_no + 1) | (1ULL << 63)); + orph->cmt_no = cpu_to_le64((c->cmt_no) | (1ULL << 63)); ubifs_assert(c->ohead_offs + len <= c->leb_size); ubifs_assert(c->ohead_lnum >= c->orph_first); ubifs_assert(c->ohead_lnum <= c->orph_last); diff --git a/fs/ubifs/ubifs.h b/fs/ubifs/ubifs.h index 6ddd1de2ea6..21502b6040f 100644 --- a/fs/ubifs/ubifs.h +++ b/fs/ubifs/ubifs.h @@ -865,7 +865,8 @@ struct ubifs_mount_opts { * @highest_inum: highest used inode number * @vfs_gen: VFS inode generation counter * @max_sqnum: current global sequence number - * @cmt_no: commit number (last successfully completed commit) + * @cmt_no: commit number of the last successfully completed commit, protected + * by @commit_sem * @cnt_lock: protects @highest_inum, @vfs_gen, and @max_sqnum counters * @fmt_version: UBIFS on-flash format version * @uuid: UUID from super block -- GitLab From de94eb558b542873d3f6f9ede1b8575fb5662248 Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Tue, 22 Jul 2008 13:06:20 +0300 Subject: [PATCH 194/750] UBIFS: optimize deletions Every time anything is deleted, UBIFS writes the deletion inode node twice - once in 'ubifs_jnl_update()' and the second time in 'ubifs_jnl_write_inode()'. However, the second write is not needed if no commit happened after 'ubifs_jnl_update()'. This patch checks that condition and avoids writing the deletion inode for the second time. Signed-off-by: Artem Bityutskiy --- fs/ubifs/journal.c | 60 ++++++++++++++++++++++++++++++++++++++++++++++ fs/ubifs/super.c | 6 +++-- fs/ubifs/ubifs.h | 12 +++++++--- 3 files changed, 73 insertions(+), 5 deletions(-) diff --git a/fs/ubifs/journal.c b/fs/ubifs/journal.c index 3bc3fc94709..0bcee7d221e 100644 --- a/fs/ubifs/journal.c +++ b/fs/ubifs/journal.c @@ -604,6 +604,7 @@ int ubifs_jnl_update(struct ubifs_info *c, const struct inode *dir, release_head(c, BASEHD); goto out_finish; } + ui->del_cmtno = c->cmt_no; } err = write_head(c, BASEHD, dent, len, &lnum, &dent_offs, sync); @@ -820,6 +821,64 @@ out_free: return err; } +/** + * ubifs_jnl_write_inode - delete an inode. + * @c: UBIFS file-system description object + * @inode: inode to delete + * + * This function deletes inode @inode which includes removing it from orphans, + * deleting it from TNC and, in some cases, writing a deletion inode to the + * journal. + * + * When regular file inodes are unlinked or a directory inode is removed, the + * 'ubifs_jnl_update()' function write corresponding deletion inode and + * direntry to the media, and adds the inode to orphans. After this, when the + * last reference to this inode has been dropped, this function is called. In + * general, it has to write one more deletion inode to the media, because if + * a commit happened between 'ubifs_jnl_update()' and + * 'ubifs_jnl_delete_inode()', the deletion inode is not in the journal + * anymore, and in fact it might be not on the flash anymore, becouse it might + * have been garbage-collected already. And for optimization reasond UBIFS does + * not read the orphan area if it has been unmounted cleanly, so it would have + * no indication in the journal that there is a deleted inode which has to be + * removed from TNC. + * + * However, if there was no commit between 'ubifs_jnl_update()' and + * 'ubifs_jnl_delete_inode()', then there is no need to write the deletion + * inode to the media for the second time. And this is quite typical case. + * + * This function returns zero in case of success and a negative error code in + * case of failure. + */ +int ubifs_jnl_delete_inode(struct ubifs_info *c, const struct inode *inode) +{ + int err; + struct ubifs_inode *ui = ubifs_inode(inode); + + ubifs_assert(inode->i_nlink == 0); + + if (ui->del_cmtno != c->cmt_no) + /* A commit happened for sure */ + return ubifs_jnl_write_inode(c, inode); + + down_read(&c->commit_sem); + /* + * Check commit number again, because the first test has been done + * without @c->commit_sem, so a commit might have happened. + */ + if (ui->del_cmtno != c->cmt_no) { + up_read(&c->commit_sem); + return ubifs_jnl_write_inode(c, inode); + } + + ubifs_delete_orphan(c, inode->i_ino); + err = ubifs_tnc_remove_ino(c, inode->i_ino); + if (err) + ubifs_ro_mode(c, err); + up_read(&c->commit_sem); + return err; +} + /** * ubifs_jnl_rename - rename a directory entry. * @c: UBIFS file-system description object @@ -928,6 +987,7 @@ int ubifs_jnl_rename(struct ubifs_info *c, const struct inode *old_dir, release_head(c, BASEHD); goto out_finish; } + new_ui->del_cmtno = c->cmt_no; } err = write_head(c, BASEHD, dent, len, &lnum, &offs, sync); diff --git a/fs/ubifs/super.c b/fs/ubifs/super.c index cf1fb6cffa0..6cc4175f23c 100644 --- a/fs/ubifs/super.c +++ b/fs/ubifs/super.c @@ -341,13 +341,15 @@ static void ubifs_delete_inode(struct inode *inode) goto out; ui->ui_size = inode->i_size = 0; - err = ubifs_jnl_write_inode(c, inode); + err = ubifs_jnl_delete_inode(c, inode); if (err) /* * Worst case we have a lost orphan inode wasting space, so a * simple error message is ok here. */ - ubifs_err("can't write inode %lu, error %d", inode->i_ino, err); + ubifs_err("can't delete inode %lu, error %d", + inode->i_ino, err); + out: if (ui->dirty) ubifs_release_dirty_inode_budget(c, ui); diff --git a/fs/ubifs/ubifs.h b/fs/ubifs/ubifs.h index 21502b6040f..dfb4b93614f 100644 --- a/fs/ubifs/ubifs.h +++ b/fs/ubifs/ubifs.h @@ -322,6 +322,8 @@ struct ubifs_gced_idx_leb { * struct ubifs_inode - UBIFS in-memory inode description. * @vfs_inode: VFS inode description object * @creat_sqnum: sequence number at time of creation + * @del_cmtno: commit number corresponding to the time the inode was deleted, + * protected by @c->commit_sem; * @xattr_size: summarized size of all extended attributes in bytes * @xattr_cnt: count of extended attributes this inode has * @xattr_names: sum of lengths of all extended attribute names belonging to @@ -372,7 +374,10 @@ struct ubifs_gced_idx_leb { */ struct ubifs_inode { struct inode vfs_inode; - unsigned long long creat_sqnum; + union { + unsigned long long creat_sqnum; + unsigned long long del_cmtno; + }; unsigned int xattr_size; unsigned int xattr_cnt; unsigned int xattr_names; @@ -779,7 +784,7 @@ struct ubifs_compressor { /** * struct ubifs_budget_req - budget requirements of an operation. * - * @fast: non-zero if the budgeting should try to aquire budget quickly and + * @fast: non-zero if the budgeting should try to acquire budget quickly and * should not try to call write-back * @recalculate: non-zero if @idx_growth, @data_growth, and @dd_growth fields * have to be re-calculated @@ -860,7 +865,7 @@ struct ubifs_mount_opts { * struct ubifs_info - UBIFS file-system description data structure * (per-superblock). * @vfs_sb: VFS @struct super_block object - * @bdi: backing device info object to make VFS happy and disable readahead + * @bdi: backing device info object to make VFS happy and disable read-ahead * * @highest_inum: highest used inode number * @vfs_gen: VFS inode generation counter @@ -1402,6 +1407,7 @@ int ubifs_jnl_update(struct ubifs_info *c, const struct inode *dir, int ubifs_jnl_write_data(struct ubifs_info *c, const struct inode *inode, const union ubifs_key *key, const void *buf, int len); int ubifs_jnl_write_inode(struct ubifs_info *c, const struct inode *inode); +int ubifs_jnl_delete_inode(struct ubifs_info *c, const struct inode *inode); int ubifs_jnl_rename(struct ubifs_info *c, const struct inode *old_dir, const struct dentry *old_dentry, const struct inode *new_dir, -- GitLab From bc813355c704e5916a86dd4b96fd226bfa3fc6ca Mon Sep 17 00:00:00 2001 From: Adrian Hunter Date: Wed, 23 Jul 2008 15:23:11 +0300 Subject: [PATCH 195/750] UBIFS: do not union creat_sqnum and del_cmtno The values in these two fields need to be preserved independently and so a union cannot be used. Signed-off-by: Adrian Hunter --- fs/ubifs/ubifs.h | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) diff --git a/fs/ubifs/ubifs.h b/fs/ubifs/ubifs.h index dfb4b93614f..d342c690724 100644 --- a/fs/ubifs/ubifs.h +++ b/fs/ubifs/ubifs.h @@ -374,10 +374,8 @@ struct ubifs_gced_idx_leb { */ struct ubifs_inode { struct inode vfs_inode; - union { - unsigned long long creat_sqnum; - unsigned long long del_cmtno; - }; + unsigned long long creat_sqnum; + unsigned long long del_cmtno; unsigned int xattr_size; unsigned int xattr_cnt; unsigned int xattr_names; -- GitLab From 7d62ff2c396470bb62a3853f14d3962eac1da974 Mon Sep 17 00:00:00 2001 From: Adrian Hunter Date: Wed, 23 Jul 2008 15:48:39 +0300 Subject: [PATCH 196/750] UBIFS: fix typos in comments Signed-off-by: Adrian Hunter --- fs/ubifs/journal.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/fs/ubifs/journal.c b/fs/ubifs/journal.c index 0bcee7d221e..25de6fde383 100644 --- a/fs/ubifs/journal.c +++ b/fs/ubifs/journal.c @@ -822,7 +822,7 @@ out_free: } /** - * ubifs_jnl_write_inode - delete an inode. + * ubifs_jnl_delete_inode - delete an inode. * @c: UBIFS file-system description object * @inode: inode to delete * @@ -831,21 +831,21 @@ out_free: * journal. * * When regular file inodes are unlinked or a directory inode is removed, the - * 'ubifs_jnl_update()' function write corresponding deletion inode and + * 'ubifs_jnl_update()' function writes a corresponding deletion inode and * direntry to the media, and adds the inode to orphans. After this, when the * last reference to this inode has been dropped, this function is called. In * general, it has to write one more deletion inode to the media, because if * a commit happened between 'ubifs_jnl_update()' and * 'ubifs_jnl_delete_inode()', the deletion inode is not in the journal - * anymore, and in fact it might be not on the flash anymore, becouse it might - * have been garbage-collected already. And for optimization reasond UBIFS does + * anymore, and in fact it might not be on the flash anymore, because it might + * have been garbage-collected already. And for optimization reasons UBIFS does * not read the orphan area if it has been unmounted cleanly, so it would have * no indication in the journal that there is a deleted inode which has to be * removed from TNC. * * However, if there was no commit between 'ubifs_jnl_update()' and * 'ubifs_jnl_delete_inode()', then there is no need to write the deletion - * inode to the media for the second time. And this is quite typical case. + * inode to the media for the second time. And this is quite a typical case. * * This function returns zero in case of success and a negative error code in * case of failure. -- GitLab From f769108424a19c7758546d1d7d19f098b1a33759 Mon Sep 17 00:00:00 2001 From: Adrian Hunter Date: Wed, 23 Jul 2008 16:55:55 +0300 Subject: [PATCH 197/750] UBIFS: correct orphan deletion order The debug function that checks orphans, does so using the TNC mutex. That means it will not see a correct picture if the inode is removed from the orphan tree before it is removed from TNC. Signed-off-by: Adrian Hunter --- fs/ubifs/journal.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/fs/ubifs/journal.c b/fs/ubifs/journal.c index 25de6fde383..acdae00aaa5 100644 --- a/fs/ubifs/journal.c +++ b/fs/ubifs/journal.c @@ -871,10 +871,11 @@ int ubifs_jnl_delete_inode(struct ubifs_info *c, const struct inode *inode) return ubifs_jnl_write_inode(c, inode); } - ubifs_delete_orphan(c, inode->i_ino); err = ubifs_tnc_remove_ino(c, inode->i_ino); if (err) ubifs_ro_mode(c, err); + else + ubifs_delete_orphan(c, inode->i_ino); up_read(&c->commit_sem); return err; } -- GitLab From 547000da6412c45456ff2ff44a171d01027bd727 Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Thu, 24 Jul 2008 14:42:05 +0300 Subject: [PATCH 198/750] UBIFS: improve budgeting checks Budgeting is a crucial UBIFS subsystem - add more assertions to improve requests checking. This is not compiled in when UBIFS debugging is disabled. Signed-off-by: Artem Bityutskiy --- fs/ubifs/budget.c | 12 ++++++++++++ fs/ubifs/ubifs.h | 8 +++++++- 2 files changed, 19 insertions(+), 1 deletion(-) diff --git a/fs/ubifs/budget.c b/fs/ubifs/budget.c index 12a1717db87..f5afce5f37b 100644 --- a/fs/ubifs/budget.c +++ b/fs/ubifs/budget.c @@ -543,6 +543,12 @@ int ubifs_budget_space(struct ubifs_info *c, struct ubifs_budget_req *req) int err, idx_growth, data_growth, dd_growth; struct retries_info ri; + ubifs_assert(req->new_page <= 1); + ubifs_assert(req->dirtied_page <= 1); + ubifs_assert(req->new_dent <= 1); + ubifs_assert(req->mod_dent <= 1); + ubifs_assert(req->new_ino <= 1); + ubifs_assert(req->new_ino_d <= UBIFS_MAX_INO_DATA); ubifs_assert(req->dirtied_ino <= 4); ubifs_assert(req->dirtied_ino_d <= UBIFS_MAX_INO_DATA * 4); @@ -618,6 +624,12 @@ again: */ void ubifs_release_budget(struct ubifs_info *c, struct ubifs_budget_req *req) { + ubifs_assert(req->new_page <= 1); + ubifs_assert(req->dirtied_page <= 1); + ubifs_assert(req->new_dent <= 1); + ubifs_assert(req->mod_dent <= 1); + ubifs_assert(req->new_ino <= 1); + ubifs_assert(req->new_ino_d <= UBIFS_MAX_INO_DATA); ubifs_assert(req->dirtied_ino <= 4); ubifs_assert(req->dirtied_ino_d <= UBIFS_MAX_INO_DATA * 4); if (!req->recalculate) { diff --git a/fs/ubifs/ubifs.h b/fs/ubifs/ubifs.h index d342c690724..565dca2ec0b 100644 --- a/fs/ubifs/ubifs.h +++ b/fs/ubifs/ubifs.h @@ -812,17 +812,23 @@ struct ubifs_compressor { struct ubifs_budget_req { unsigned int fast:1; unsigned int recalculate:1; +#ifndef UBIFS_DEBUG unsigned int new_page:1; unsigned int dirtied_page:1; unsigned int new_dent:1; unsigned int mod_dent:1; unsigned int new_ino:1; unsigned int new_ino_d:13; -#ifndef UBIFS_DEBUG unsigned int dirtied_ino:4; unsigned int dirtied_ino_d:15; #else /* Not bit-fields to check for overflows */ + unsigned int new_page; + unsigned int dirtied_page; + unsigned int new_dent; + unsigned int mod_dent; + unsigned int new_ino; + unsigned int new_ino_d; unsigned int dirtied_ino; unsigned int dirtied_ino_d; #endif -- GitLab From dab4b4d2f915a65022343012a795f4ae4ae7e83c Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Thu, 24 Jul 2008 14:52:45 +0300 Subject: [PATCH 199/750] UBIFS: align inode data to eight UBIFS aligns node lengths to 8, so budgeting has to do the same. Well, direntry, inode, and page budgets are already aligned, but not inode data budget (e.g., data in special devices or symlinks). Do this for inode data as well. Also, add corresponding debugging checks. Signed-off-by: Artem Bityutskiy --- fs/ubifs/budget.c | 10 +++++++++- fs/ubifs/dir.c | 10 ++++++---- fs/ubifs/file.c | 4 ++-- fs/ubifs/ubifs.h | 4 ++++ fs/ubifs/xattr.c | 4 ++-- 5 files changed, 23 insertions(+), 9 deletions(-) diff --git a/fs/ubifs/budget.c b/fs/ubifs/budget.c index f5afce5f37b..a3978ba4215 100644 --- a/fs/ubifs/budget.c +++ b/fs/ubifs/budget.c @@ -551,6 +551,8 @@ int ubifs_budget_space(struct ubifs_info *c, struct ubifs_budget_req *req) ubifs_assert(req->new_ino_d <= UBIFS_MAX_INO_DATA); ubifs_assert(req->dirtied_ino <= 4); ubifs_assert(req->dirtied_ino_d <= UBIFS_MAX_INO_DATA * 4); + ubifs_assert(!(req->new_ino_d & 7)); + ubifs_assert(!(req->dirtied_ino_d & 7)); data_growth = calc_data_growth(c, req); dd_growth = calc_dd_growth(c, req); @@ -632,6 +634,8 @@ void ubifs_release_budget(struct ubifs_info *c, struct ubifs_budget_req *req) ubifs_assert(req->new_ino_d <= UBIFS_MAX_INO_DATA); ubifs_assert(req->dirtied_ino <= 4); ubifs_assert(req->dirtied_ino_d <= UBIFS_MAX_INO_DATA * 4); + ubifs_assert(!(req->new_ino_d & 7)); + ubifs_assert(!(req->dirtied_ino_d & 7)); if (!req->recalculate) { ubifs_assert(req->idx_growth >= 0); ubifs_assert(req->data_growth >= 0); @@ -659,7 +663,11 @@ void ubifs_release_budget(struct ubifs_info *c, struct ubifs_budget_req *req) ubifs_assert(c->budg_idx_growth >= 0); ubifs_assert(c->budg_data_growth >= 0); + ubifs_assert(c->budg_dd_growth >= 0); ubifs_assert(c->min_idx_lebs < c->main_lebs); + ubifs_assert(!(c->budg_idx_growth & 7)); + ubifs_assert(!(c->budg_data_growth & 7)); + ubifs_assert(!(c->budg_dd_growth & 7)); spin_unlock(&c->space_lock); } @@ -701,7 +709,7 @@ void ubifs_release_dirty_inode_budget(struct ubifs_info *c, struct ubifs_budget_req req; memset(&req, 0, sizeof(struct ubifs_budget_req)); - req.dd_growth = c->inode_budget + ui->data_len; + req.dd_growth = c->inode_budget + ALIGN(ui->data_len, 8); ubifs_release_budget(c, &req); } diff --git a/fs/ubifs/dir.c b/fs/ubifs/dir.c index a79e850fee6..eba3a8a7c33 100644 --- a/fs/ubifs/dir.c +++ b/fs/ubifs/dir.c @@ -525,7 +525,7 @@ static int ubifs_link(struct dentry *old_dentry, struct inode *dir, struct ubifs_inode *dir_ui = ubifs_inode(dir); int err, sz_change = CALC_DENT_SIZE(dentry->d_name.len); struct ubifs_budget_req req = { .new_dent = 1, .dirtied_ino = 2, - .dirtied_ino_d = ui->data_len }; + .dirtied_ino_d = ALIGN(ui->data_len, 8) }; /* * Budget request settings: new direntry, changing the target inode, @@ -788,7 +788,8 @@ static int ubifs_mknod(struct inode *dir, struct dentry *dentry, int sz_change = CALC_DENT_SIZE(dentry->d_name.len); int err, devlen = 0; struct ubifs_budget_req req = { .new_ino = 1, .new_dent = 1, - .new_ino_d = devlen, .dirtied_ino = 1 }; + .new_ino_d = ALIGN(devlen, 8), + .dirtied_ino = 1 }; /* * Budget request settings: new inode, new direntry and changing parent @@ -862,7 +863,8 @@ static int ubifs_symlink(struct inode *dir, struct dentry *dentry, int err, len = strlen(symname); int sz_change = CALC_DENT_SIZE(dentry->d_name.len); struct ubifs_budget_req req = { .new_ino = 1, .new_dent = 1, - .new_ino_d = len, .dirtied_ino = 1 }; + .new_ino_d = ALIGN(len, 8), + .dirtied_ino = 1 }; /* * Budget request settings: new inode, new direntry and changing parent @@ -1011,7 +1013,7 @@ static int ubifs_rename(struct inode *old_dir, struct dentry *old_dentry, struct ubifs_budget_req req = { .new_dent = 1, .mod_dent = 1, .dirtied_ino = 3 }; struct ubifs_budget_req ino_req = { .dirtied_ino = 1, - .dirtied_ino_d = old_inode_ui->data_len }; + .dirtied_ino_d = ALIGN(old_inode_ui->data_len, 8) }; struct timespec time; /* diff --git a/fs/ubifs/file.c b/fs/ubifs/file.c index 01598f28020..9fecab2f30b 100644 --- a/fs/ubifs/file.c +++ b/fs/ubifs/file.c @@ -890,7 +890,7 @@ static int do_setattr(struct ubifs_info *c, struct inode *inode, loff_t new_size = attr->ia_size; struct ubifs_inode *ui = ubifs_inode(inode); struct ubifs_budget_req req = { .dirtied_ino = 1, - .dirtied_ino_d = ui->data_len }; + .dirtied_ino_d = ALIGN(ui->data_len, 8) }; err = ubifs_budget_space(c, &req); if (err) @@ -1052,7 +1052,7 @@ static int update_mctime(struct ubifs_info *c, struct inode *inode) if (mctime_update_needed(inode, &now)) { int err, release; struct ubifs_budget_req req = { .dirtied_ino = 1, - .dirtied_ino_d = ui->data_len }; + .dirtied_ino_d = ALIGN(ui->data_len, 8) }; err = ubifs_budget_space(c, &req); if (err) diff --git a/fs/ubifs/ubifs.h b/fs/ubifs/ubifs.h index 565dca2ec0b..73ca8a00979 100644 --- a/fs/ubifs/ubifs.h +++ b/fs/ubifs/ubifs.h @@ -808,6 +808,10 @@ struct ubifs_compressor { * An inode may contain 4KiB of data at max., thus the widths of @new_ino_d * is 13 bits, and @dirtied_ino_d - 15, because up to 4 inodes may be made * dirty by the re-name operation. + * + * Note, UBIFS aligns node lengths to 8-bytes boundary, so the requester has to + * make sure the amount of inode data which contribute to @new_ino_d and + * @dirtied_ino_d fields are aligned. */ struct ubifs_budget_req { unsigned int fast:1; diff --git a/fs/ubifs/xattr.c b/fs/ubifs/xattr.c index 1388a078e1a..39e831d074c 100644 --- a/fs/ubifs/xattr.c +++ b/fs/ubifs/xattr.c @@ -103,8 +103,8 @@ static int create_xattr(struct ubifs_info *c, struct inode *host, struct inode *inode; struct ubifs_inode *ui, *host_ui = ubifs_inode(host); struct ubifs_budget_req req = { .new_ino = 1, .new_dent = 1, - .new_ino_d = size, .dirtied_ino = 1, - .dirtied_ino_d = host_ui->data_len}; + .new_ino_d = size, .dirtied_ino = 1, + .dirtied_ino_d = ALIGN(host_ui->data_len, 8)}; if (host_ui->xattr_cnt >= MAX_XATTRS_PER_INODE) return -ENOSPC; -- GitLab From 1de9415906bccab51fb74c6adf575948610f0909 Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Fri, 25 Jul 2008 12:58:38 +0300 Subject: [PATCH 200/750] UBIFS: print pid in dump function Useful when something fails and there are many processes racing. Signed-off-by: Artem Bityutskiy --- fs/ubifs/debug.c | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) diff --git a/fs/ubifs/debug.c b/fs/ubifs/debug.c index 0adfb29b850..b9cb7747375 100644 --- a/fs/ubifs/debug.c +++ b/fs/ubifs/debug.c @@ -568,8 +568,8 @@ void dbg_dump_budget_req(const struct ubifs_budget_req *req) void dbg_dump_lstats(const struct ubifs_lp_stats *lst) { spin_lock(&dbg_lock); - printk(KERN_DEBUG "Lprops statistics: empty_lebs %d, idx_lebs %d\n", - lst->empty_lebs, lst->idx_lebs); + printk(KERN_DEBUG "(pid %d) Lprops statistics: empty_lebs %d, " + "idx_lebs %d\n", current->pid, lst->empty_lebs, lst->idx_lebs); printk(KERN_DEBUG "\ttaken_empty_lebs %d, total_free %lld, " "total_dirty %lld\n", lst->taken_empty_lebs, lst->total_free, lst->total_dirty); @@ -587,8 +587,8 @@ void dbg_dump_budg(struct ubifs_info *c) struct ubifs_gced_idx_leb *idx_gc; spin_lock(&dbg_lock); - printk(KERN_DEBUG "Budgeting info: budg_data_growth %lld, " - "budg_dd_growth %lld, budg_idx_growth %lld\n", + printk(KERN_DEBUG "(pid %d) Budgeting info: budg_data_growth %lld, " + "budg_dd_growth %lld, budg_idx_growth %lld\n", current->pid, c->budg_data_growth, c->budg_dd_growth, c->budg_idx_growth); printk(KERN_DEBUG "\tdata budget sum %lld, total budget sum %lld, " "freeable_cnt %d\n", c->budg_data_growth + c->budg_dd_growth, @@ -634,7 +634,7 @@ void dbg_dump_lprops(struct ubifs_info *c) struct ubifs_lprops lp; struct ubifs_lp_stats lst; - printk(KERN_DEBUG "Dumping LEB properties\n"); + printk(KERN_DEBUG "(pid %d) Dumping LEB properties\n", current->pid); ubifs_get_lp_stats(c, &lst); dbg_dump_lstats(&lst); @@ -655,7 +655,7 @@ void dbg_dump_leb(const struct ubifs_info *c, int lnum) if (dbg_failure_mode) return; - printk(KERN_DEBUG "Dumping LEB %d\n", lnum); + printk(KERN_DEBUG "(pid %d) Dumping LEB %d\n", current->pid, lnum); sleb = ubifs_scan(c, lnum, 0, c->dbg_buf); if (IS_ERR(sleb)) { @@ -720,8 +720,8 @@ void dbg_dump_heap(struct ubifs_info *c, struct ubifs_lpt_heap *heap, int cat) { int i; - printk(KERN_DEBUG "Dumping heap cat %d (%d elements)\n", - cat, heap->cnt); + printk(KERN_DEBUG "(pid %d) Dumping heap cat %d (%d elements)\n", + current->pid, cat, heap->cnt); for (i = 0; i < heap->cnt; i++) { struct ubifs_lprops *lprops = heap->arr[i]; @@ -736,7 +736,7 @@ void dbg_dump_pnode(struct ubifs_info *c, struct ubifs_pnode *pnode, { int i; - printk(KERN_DEBUG "Dumping pnode:\n"); + printk(KERN_DEBUG "(pid %d) Dumping pnode:\n", current->pid); printk(KERN_DEBUG "\taddress %zx parent %zx cnext %zx\n", (size_t)pnode, (size_t)parent, (size_t)pnode->cnext); printk(KERN_DEBUG "\tflags %lu iip %d level %d num %d\n", @@ -755,7 +755,7 @@ void dbg_dump_tnc(struct ubifs_info *c) int level; printk(KERN_DEBUG "\n"); - printk(KERN_DEBUG "Dumping the TNC tree\n"); + printk(KERN_DEBUG "(pid %d) Dumping the TNC tree\n", current->pid); znode = ubifs_tnc_levelorder_next(c->zroot.znode, NULL); level = znode->level; printk(KERN_DEBUG "== Level %d ==\n", level); -- GitLab From b364b41aeb0289be402be83eebca92eb90bfcb8b Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Fri, 25 Jul 2008 14:38:51 +0300 Subject: [PATCH 201/750] UBIFS: reserve more space for index At the moment UBIFS reserves twice old index size space for the index. But this is not enough in some cases, because if the indexing node are very fragmented and there are many small gaps, while the dirty index has big znodes - in-the-gaps method would fail. Thus, reserve trise as more, in which case we are guaranteed that we can commit in any case. Signed-off-by: Artem Bityutskiy --- fs/ubifs/budget.c | 8 ++++---- fs/ubifs/find.c | 9 +++++++-- fs/ubifs/misc.h | 2 +- fs/ubifs/ubifs-media.h | 4 ++-- 4 files changed, 14 insertions(+), 9 deletions(-) diff --git a/fs/ubifs/budget.c b/fs/ubifs/budget.c index a3978ba4215..323d83a4d09 100644 --- a/fs/ubifs/budget.c +++ b/fs/ubifs/budget.c @@ -263,8 +263,8 @@ int ubifs_calc_min_idx_lebs(struct ubifs_info *c) idx_size = c->old_idx_sz + c->budg_idx_growth + c->budg_uncommitted_idx; - /* And make sure we have twice the index size of space reserved */ - idx_size <<= 1; + /* And make sure we have trice the index size of space reserved */ + idx_size = idx_size + (idx_size << 1); /* * We do not maintain 'old_idx_size' as 'old_idx_lebs'/'old_idx_bytes' @@ -388,11 +388,11 @@ static int can_use_rp(struct ubifs_info *c) * This function makes sure UBIFS has enough free eraseblocks for index growth * and data. * - * When budgeting index space, UBIFS reserves twice as more LEBs as the index + * When budgeting index space, UBIFS reserves trice as more LEBs as the index * would take if it was consolidated and written to the flash. This guarantees * that the "in-the-gaps" commit method always succeeds and UBIFS will always * be able to commit dirty index. So this function basically adds amount of - * budgeted index space to the size of the current index, multiplies this by 2, + * budgeted index space to the size of the current index, multiplies this by 3, * and makes sure this does not exceed the amount of free eraseblocks. * * Notes about @c->min_idx_lebs and @c->lst.idx_lebs variables: diff --git a/fs/ubifs/find.c b/fs/ubifs/find.c index 10394c54836..c70c7679c1b 100644 --- a/fs/ubifs/find.c +++ b/fs/ubifs/find.c @@ -290,9 +290,14 @@ int ubifs_find_dirty_leb(struct ubifs_info *c, struct ubifs_lprops *ret_lp, idx_lp = idx_heap->arr[0]; sum = idx_lp->free + idx_lp->dirty; /* - * Since we reserve twice as more space for the index than it + * Since we reserve trice as more space for the index than it * actually takes, it does not make sense to pick indexing LEBs - * with less than half LEB of dirty space. + * with less than, say, half LEB of dirty space. May be half is + * not the optimal boundary - this should be tested and + * checked. This boundary should determine how much we use + * in-the-gaps to consolidate the index comparing to how much + * we use garbage collector to consolidate it. The "half" + * criteria just feels to be fine. */ if (sum < min_space || sum < c->half_leb_size) idx_lp = NULL; diff --git a/fs/ubifs/misc.h b/fs/ubifs/misc.h index cd83ffc8101..87dabf9fe74 100644 --- a/fs/ubifs/misc.h +++ b/fs/ubifs/misc.h @@ -308,7 +308,7 @@ static inline long long ubifs_reported_space(const struct ubifs_info *c, { int divisor, factor; - divisor = UBIFS_MAX_DATA_NODE_SZ + (c->max_idx_node_sz << 1); + divisor = UBIFS_MAX_DATA_NODE_SZ + (c->max_idx_node_sz * 3); factor = UBIFS_MAX_DATA_NODE_SZ - UBIFS_DATA_NODE_SZ; do_div(free, divisor); diff --git a/fs/ubifs/ubifs-media.h b/fs/ubifs/ubifs-media.h index 0cc7da9bed4..bd2121f3426 100644 --- a/fs/ubifs/ubifs-media.h +++ b/fs/ubifs/ubifs-media.h @@ -228,10 +228,10 @@ enum { /* Minimum number of orphan area logical eraseblocks */ #define UBIFS_MIN_ORPH_LEBS 1 /* - * Minimum number of main area logical eraseblocks (buds, 2 for the index, 1 + * Minimum number of main area logical eraseblocks (buds, 3 for the index, 1 * for GC, 1 for deletions, and at least 1 for committed data). */ -#define UBIFS_MIN_MAIN_LEBS (UBIFS_MIN_BUD_LEBS + 5) +#define UBIFS_MIN_MAIN_LEBS (UBIFS_MIN_BUD_LEBS + 6) /* Minimum number of logical eraseblocks */ #define UBIFS_MIN_LEB_CNT (UBIFS_SB_LEBS + UBIFS_MST_LEBS + \ -- GitLab From 0010f18afc5f8ba25e1d20e3165894c32a65af02 Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Fri, 25 Jul 2008 16:39:44 +0300 Subject: [PATCH 202/750] UBIFS: minor tweaks in commit No functional changes, just lessen the amount of indentations. Signed-off-by: Artem Bityutskiy --- fs/ubifs/tnc_commit.c | 37 ++++++++++++++++++------------------- 1 file changed, 18 insertions(+), 19 deletions(-) diff --git a/fs/ubifs/tnc_commit.c b/fs/ubifs/tnc_commit.c index 8117e65ba2e..8ac76b1c2d5 100644 --- a/fs/ubifs/tnc_commit.c +++ b/fs/ubifs/tnc_commit.c @@ -372,26 +372,25 @@ static int layout_in_gaps(struct ubifs_info *c, int cnt) written = layout_leb_in_gaps(c, p); if (written < 0) { err = written; - if (err == -ENOSPC) { - if (!dbg_force_in_the_gaps_enabled) { - /* - * Do not print scary warnings if the - * debugging option which forces - * in-the-gaps is enabled. - */ - ubifs_err("out of space"); - spin_lock(&c->space_lock); - dbg_dump_budg(c); - spin_unlock(&c->space_lock); - dbg_dump_lprops(c); - } - /* Try to commit anyway */ - err = 0; - break; + if (err != -ENOSPC) { + kfree(c->gap_lebs); + c->gap_lebs = NULL; + return err; } - kfree(c->gap_lebs); - c->gap_lebs = NULL; - return err; + if (!dbg_force_in_the_gaps_enabled) { + /* + * Do not print scary warnings if the debugging + * option which forces in-the-gaps is enabled. + */ + ubifs_err("out of space"); + spin_lock(&c->space_lock); + dbg_dump_budg(c); + spin_unlock(&c->space_lock); + dbg_dump_lprops(c); + } + /* Try to commit anyway */ + err = 0; + break; } p++; cnt -= written; -- GitLab From 22bc7fa8c5da09805edc6a6199ce81373b2c207d Mon Sep 17 00:00:00 2001 From: Zoltan Sogor Date: Mon, 28 Jul 2008 16:28:49 +0200 Subject: [PATCH 203/750] UBIFS: support splice_write Signed-off-by: Zoltan Sogor Signed-off-by: Artem Bityutskiy --- fs/ubifs/file.c | 1 + 1 file changed, 1 insertion(+) diff --git a/fs/ubifs/file.c b/fs/ubifs/file.c index 9fecab2f30b..4071d1cae29 100644 --- a/fs/ubifs/file.c +++ b/fs/ubifs/file.c @@ -1271,6 +1271,7 @@ struct file_operations ubifs_file_operations = { .fsync = ubifs_fsync, .unlocked_ioctl = ubifs_ioctl, .splice_read = generic_file_splice_read, + .splice_write = generic_file_splice_write, #ifdef CONFIG_COMPAT .compat_ioctl = ubifs_compat_ioctl, #endif -- GitLab From 3a13252c6f3a029ac992a36910e945f361482797 Mon Sep 17 00:00:00 2001 From: Adrian Hunter Date: Wed, 30 Jul 2008 12:18:02 +0300 Subject: [PATCH 204/750] UBIFS: correct spelling of "thrice". Signed-off-by: Adrian Hunter --- fs/ubifs/budget.c | 4 ++-- fs/ubifs/find.c | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-) diff --git a/fs/ubifs/budget.c b/fs/ubifs/budget.c index 323d83a4d09..15409815747 100644 --- a/fs/ubifs/budget.c +++ b/fs/ubifs/budget.c @@ -263,7 +263,7 @@ int ubifs_calc_min_idx_lebs(struct ubifs_info *c) idx_size = c->old_idx_sz + c->budg_idx_growth + c->budg_uncommitted_idx; - /* And make sure we have trice the index size of space reserved */ + /* And make sure we have thrice the index size of space reserved */ idx_size = idx_size + (idx_size << 1); /* @@ -388,7 +388,7 @@ static int can_use_rp(struct ubifs_info *c) * This function makes sure UBIFS has enough free eraseblocks for index growth * and data. * - * When budgeting index space, UBIFS reserves trice as more LEBs as the index + * When budgeting index space, UBIFS reserves thrice as many LEBs as the index * would take if it was consolidated and written to the flash. This guarantees * that the "in-the-gaps" commit method always succeeds and UBIFS will always * be able to commit dirty index. So this function basically adds amount of diff --git a/fs/ubifs/find.c b/fs/ubifs/find.c index c70c7679c1b..adee7b5ddea 100644 --- a/fs/ubifs/find.c +++ b/fs/ubifs/find.c @@ -290,7 +290,7 @@ int ubifs_find_dirty_leb(struct ubifs_info *c, struct ubifs_lprops *ret_lp, idx_lp = idx_heap->arr[0]; sum = idx_lp->free + idx_lp->dirty; /* - * Since we reserve trice as more space for the index than it + * Since we reserve thrice as much space for the index than it * actually takes, it does not make sense to pick indexing LEBs * with less than, say, half LEB of dirty space. May be half is * not the optimal boundary - this should be tested and -- GitLab From 81ffa38e1558f54db190e2d11e7260ab09c4acf2 Mon Sep 17 00:00:00 2001 From: Adrian Hunter Date: Fri, 1 Aug 2008 15:35:08 +0300 Subject: [PATCH 205/750] UBIFS: always set i_generation to 0 UBIFS does not presently re-use inode numbers, so leaving i_generation zero is most appropriate for now. Signed-off-by: Adrian Hunter Signed-off-by: Artem Bityutskiy --- fs/ubifs/dir.c | 1 - fs/ubifs/super.c | 2 -- fs/ubifs/ubifs.h | 4 +--- 3 files changed, 1 insertion(+), 6 deletions(-) diff --git a/fs/ubifs/dir.c b/fs/ubifs/dir.c index eba3a8a7c33..0d1ab8967a4 100644 --- a/fs/ubifs/dir.c +++ b/fs/ubifs/dir.c @@ -165,7 +165,6 @@ struct inode *ubifs_new_inode(struct ubifs_info *c, const struct inode *dir, } inode->i_ino = ++c->highest_inum; - inode->i_generation = ++c->vfs_gen; /* * The creation sequence number remains with this inode for its * lifetime. All nodes for this inode have a greater sequence number, diff --git a/fs/ubifs/super.c b/fs/ubifs/super.c index 6cc4175f23c..2c268a47641 100644 --- a/fs/ubifs/super.c +++ b/fs/ubifs/super.c @@ -30,7 +30,6 @@ #include #include #include -#include #include #include #include @@ -1671,7 +1670,6 @@ static int ubifs_fill_super(struct super_block *sb, void *data, int silent) INIT_LIST_HEAD(&c->orph_new); c->highest_inum = UBIFS_FIRST_INO; - get_random_bytes(&c->vfs_gen, sizeof(int)); c->lhead_lnum = c->ltail_lnum = UBIFS_LOG_LNUM; ubi_get_volume_info(ubi, &c->vi); diff --git a/fs/ubifs/ubifs.h b/fs/ubifs/ubifs.h index 73ca8a00979..f2dd749d798 100644 --- a/fs/ubifs/ubifs.h +++ b/fs/ubifs/ubifs.h @@ -876,11 +876,10 @@ struct ubifs_mount_opts { * @bdi: backing device info object to make VFS happy and disable read-ahead * * @highest_inum: highest used inode number - * @vfs_gen: VFS inode generation counter * @max_sqnum: current global sequence number * @cmt_no: commit number of the last successfully completed commit, protected * by @commit_sem - * @cnt_lock: protects @highest_inum, @vfs_gen, and @max_sqnum counters + * @cnt_lock: protects @highest_inum and @max_sqnum counters * @fmt_version: UBIFS on-flash format version * @uuid: UUID from super block * @@ -1117,7 +1116,6 @@ struct ubifs_info { struct backing_dev_info bdi; ino_t highest_inum; - unsigned int vfs_gen; unsigned long long max_sqnum; unsigned long long cmt_no; spinlock_t cnt_lock; -- GitLab From 840dc6b891d521f18bf081bd5a32e4a1f8110abc Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Fri, 1 Aug 2008 18:13:37 +0300 Subject: [PATCH 206/750] UBIFS: improve arguments checking in debugging messages Use "if (0) printk()" construct in debugging print macros to make the debugging messages be checked even if debugging is off. This patch also removes some unneeded spaces and blank lines. Signed-off-by: Artem Bityutskiy --- fs/ubifs/debug.h | 143 +++++++++++++++++++++++------------------------ 1 file changed, 69 insertions(+), 74 deletions(-) diff --git a/fs/ubifs/debug.h b/fs/ubifs/debug.h index 3c4f1e93c9e..50315fc5718 100644 --- a/fs/ubifs/debug.h +++ b/fs/ubifs/debug.h @@ -27,7 +27,7 @@ #define UBIFS_DBG(op) op -#define ubifs_assert(expr) do { \ +#define ubifs_assert(expr) do { \ if (unlikely(!(expr))) { \ printk(KERN_CRIT "UBIFS assert failed in %s at %u (pid %d)\n", \ __func__, __LINE__, current->pid); \ @@ -73,50 +73,50 @@ const char *dbg_key_str1(const struct ubifs_info *c, const union ubifs_key *key); /* - * DBGKEY macros require dbg_lock to be held, which it is in the dbg message + * DBGKEY macros require @dbg_lock to be held, which it is in the dbg message * macros. */ #define DBGKEY(key) dbg_key_str0(c, (key)) #define DBGKEY1(key) dbg_key_str1(c, (key)) /* General messages */ -#define dbg_gen(fmt, ...) dbg_do_msg(UBIFS_MSG_GEN, fmt, ##__VA_ARGS__) +#define dbg_gen(fmt, ...) dbg_do_msg(UBIFS_MSG_GEN, fmt, ##__VA_ARGS__) /* Additional journal messages */ -#define dbg_jnl(fmt, ...) dbg_do_msg(UBIFS_MSG_JNL, fmt, ##__VA_ARGS__) +#define dbg_jnl(fmt, ...) dbg_do_msg(UBIFS_MSG_JNL, fmt, ##__VA_ARGS__) /* Additional TNC messages */ -#define dbg_tnc(fmt, ...) dbg_do_msg(UBIFS_MSG_TNC, fmt, ##__VA_ARGS__) +#define dbg_tnc(fmt, ...) dbg_do_msg(UBIFS_MSG_TNC, fmt, ##__VA_ARGS__) /* Additional lprops messages */ -#define dbg_lp(fmt, ...) dbg_do_msg(UBIFS_MSG_LP, fmt, ##__VA_ARGS__) +#define dbg_lp(fmt, ...) dbg_do_msg(UBIFS_MSG_LP, fmt, ##__VA_ARGS__) /* Additional LEB find messages */ -#define dbg_find(fmt, ...) dbg_do_msg(UBIFS_MSG_FIND, fmt, ##__VA_ARGS__) +#define dbg_find(fmt, ...) dbg_do_msg(UBIFS_MSG_FIND, fmt, ##__VA_ARGS__) /* Additional mount messages */ -#define dbg_mnt(fmt, ...) dbg_do_msg(UBIFS_MSG_MNT, fmt, ##__VA_ARGS__) +#define dbg_mnt(fmt, ...) dbg_do_msg(UBIFS_MSG_MNT, fmt, ##__VA_ARGS__) /* Additional I/O messages */ -#define dbg_io(fmt, ...) dbg_do_msg(UBIFS_MSG_IO, fmt, ##__VA_ARGS__) +#define dbg_io(fmt, ...) dbg_do_msg(UBIFS_MSG_IO, fmt, ##__VA_ARGS__) /* Additional commit messages */ -#define dbg_cmt(fmt, ...) dbg_do_msg(UBIFS_MSG_CMT, fmt, ##__VA_ARGS__) +#define dbg_cmt(fmt, ...) dbg_do_msg(UBIFS_MSG_CMT, fmt, ##__VA_ARGS__) /* Additional budgeting messages */ -#define dbg_budg(fmt, ...) dbg_do_msg(UBIFS_MSG_BUDG, fmt, ##__VA_ARGS__) +#define dbg_budg(fmt, ...) dbg_do_msg(UBIFS_MSG_BUDG, fmt, ##__VA_ARGS__) /* Additional log messages */ -#define dbg_log(fmt, ...) dbg_do_msg(UBIFS_MSG_LOG, fmt, ##__VA_ARGS__) +#define dbg_log(fmt, ...) dbg_do_msg(UBIFS_MSG_LOG, fmt, ##__VA_ARGS__) /* Additional gc messages */ -#define dbg_gc(fmt, ...) dbg_do_msg(UBIFS_MSG_GC, fmt, ##__VA_ARGS__) +#define dbg_gc(fmt, ...) dbg_do_msg(UBIFS_MSG_GC, fmt, ##__VA_ARGS__) /* Additional scan messages */ -#define dbg_scan(fmt, ...) dbg_do_msg(UBIFS_MSG_SCAN, fmt, ##__VA_ARGS__) +#define dbg_scan(fmt, ...) dbg_do_msg(UBIFS_MSG_SCAN, fmt, ##__VA_ARGS__) /* Additional recovery messages */ -#define dbg_rcvry(fmt, ...) dbg_do_msg(UBIFS_MSG_RCVRY, fmt, ##__VA_ARGS__) +#define dbg_rcvry(fmt, ...) dbg_do_msg(UBIFS_MSG_RCVRY, fmt, ##__VA_ARGS__) /* * Debugging message type flags (must match msg_type_names in debug.c). @@ -239,34 +239,23 @@ typedef int (*dbg_leaf_callback)(struct ubifs_info *c, struct ubifs_zbranch *zbr, void *priv); typedef int (*dbg_znode_callback)(struct ubifs_info *c, struct ubifs_znode *znode, void *priv); - int dbg_walk_index(struct ubifs_info *c, dbg_leaf_callback leaf_cb, dbg_znode_callback znode_cb, void *priv); /* Checking functions */ int dbg_check_lprops(struct ubifs_info *c); - int dbg_old_index_check_init(struct ubifs_info *c, struct ubifs_zbranch *zroot); int dbg_check_old_index(struct ubifs_info *c, struct ubifs_zbranch *zroot); - int dbg_check_cats(struct ubifs_info *c); - int dbg_check_ltab(struct ubifs_info *c); - int dbg_check_synced_i_size(struct inode *inode); - int dbg_check_dir_size(struct ubifs_info *c, const struct inode *dir); - int dbg_check_tnc(struct ubifs_info *c, int extra); - int dbg_check_idx_size(struct ubifs_info *c, long long idx_size); - int dbg_check_filesystem(struct ubifs_info *c); - void dbg_check_heap(struct ubifs_info *c, struct ubifs_lpt_heap *heap, int cat, int add_pos); - int dbg_check_lprops(struct ubifs_info *c); int dbg_check_lpt_nodes(struct ubifs_info *c, struct ubifs_cnode *cnode, int row, int col); @@ -329,71 +318,77 @@ static inline int dbg_change(struct ubi_volume_desc *desc, int lnum, #else /* !CONFIG_UBIFS_FS_DEBUG */ #define UBIFS_DBG(op) -#define ubifs_assert(expr) ({}) -#define ubifs_assert_cmt_locked(c) + +/* Use "if (0)" to make compiler check arguments even if debugging is off */ +#define ubifs_assert(expr) do { \ + if (0 && (expr)) \ + printk(KERN_CRIT "UBIFS assert failed in %s at %u (pid %d)\n", \ + __func__, __LINE__, current->pid); \ +} while (0) + +#define dbg_err(fmt, ...) do { \ + if (0) \ + ubifs_err(fmt, ##__VA_ARGS__); \ +} while (0) + +#define dbg_msg(fmt, ...) do { \ + if (0) \ + printk(KERN_DEBUG "UBIFS DBG (pid %d): %s: " fmt "\n", \ + current->pid, __func__, ##__VA_ARGS__); \ +} while (0) + #define dbg_dump_stack() -#define dbg_err(fmt, ...) ({}) -#define dbg_msg(fmt, ...) ({}) -#define dbg_key(c, key, fmt, ...) ({}) - -#define dbg_gen(fmt, ...) ({}) -#define dbg_jnl(fmt, ...) ({}) -#define dbg_tnc(fmt, ...) ({}) -#define dbg_lp(fmt, ...) ({}) -#define dbg_find(fmt, ...) ({}) -#define dbg_mnt(fmt, ...) ({}) -#define dbg_io(fmt, ...) ({}) -#define dbg_cmt(fmt, ...) ({}) -#define dbg_budg(fmt, ...) ({}) -#define dbg_log(fmt, ...) ({}) -#define dbg_gc(fmt, ...) ({}) -#define dbg_scan(fmt, ...) ({}) -#define dbg_rcvry(fmt, ...) ({}) - -#define dbg_ntype(type) "" -#define dbg_cstate(cmt_state) "" -#define dbg_get_key_dump(c, key) ({}) -#define dbg_dump_inode(c, inode) ({}) -#define dbg_dump_node(c, node) ({}) -#define dbg_dump_budget_req(req) ({}) -#define dbg_dump_lstats(lst) ({}) -#define dbg_dump_budg(c) ({}) -#define dbg_dump_lprop(c, lp) ({}) -#define dbg_dump_lprops(c) ({}) -#define dbg_dump_leb(c, lnum) ({}) -#define dbg_dump_znode(c, znode) ({}) -#define dbg_dump_heap(c, heap, cat) ({}) -#define dbg_dump_pnode(c, pnode, parent, iip) ({}) -#define dbg_dump_tnc(c) ({}) -#define dbg_dump_index(c) ({}) +#define ubifs_assert_cmt_locked(c) -#define dbg_walk_index(c, leaf_cb, znode_cb, priv) 0 +#define dbg_gen(fmt, ...) dbg_msg(fmt, ##__VA_ARGS__) +#define dbg_jnl(fmt, ...) dbg_msg(fmt, ##__VA_ARGS__) +#define dbg_tnc(fmt, ...) dbg_msg(fmt, ##__VA_ARGS__) +#define dbg_lp(fmt, ...) dbg_msg(fmt, ##__VA_ARGS__) +#define dbg_find(fmt, ...) dbg_msg(fmt, ##__VA_ARGS__) +#define dbg_mnt(fmt, ...) dbg_msg(fmt, ##__VA_ARGS__) +#define dbg_io(fmt, ...) dbg_msg(fmt, ##__VA_ARGS__) +#define dbg_cmt(fmt, ...) dbg_msg(fmt, ##__VA_ARGS__) +#define dbg_budg(fmt, ...) dbg_msg(fmt, ##__VA_ARGS__) +#define dbg_log(fmt, ...) dbg_msg(fmt, ##__VA_ARGS__) +#define dbg_gc(fmt, ...) dbg_msg(fmt, ##__VA_ARGS__) +#define dbg_scan(fmt, ...) dbg_msg(fmt, ##__VA_ARGS__) +#define dbg_rcvry(fmt, ...) dbg_msg(fmt, ##__VA_ARGS__) + +#define DBGKEY(key) ((char *)(key)) +#define DBGKEY1(key) ((char *)(key)) + +#define dbg_ntype(type) "" +#define dbg_cstate(cmt_state) "" +#define dbg_get_key_dump(c, key) ({}) +#define dbg_dump_inode(c, inode) ({}) +#define dbg_dump_node(c, node) ({}) +#define dbg_dump_budget_req(req) ({}) +#define dbg_dump_lstats(lst) ({}) +#define dbg_dump_budg(c) ({}) +#define dbg_dump_lprop(c, lp) ({}) +#define dbg_dump_lprops(c) ({}) +#define dbg_dump_leb(c, lnum) ({}) +#define dbg_dump_znode(c, znode) ({}) +#define dbg_dump_heap(c, heap, cat) ({}) +#define dbg_dump_pnode(c, pnode, parent, iip) ({}) +#define dbg_dump_tnc(c) ({}) +#define dbg_dump_index(c) ({}) +#define dbg_walk_index(c, leaf_cb, znode_cb, priv) 0 #define dbg_old_index_check_init(c, zroot) 0 #define dbg_check_old_index(c, zroot) 0 - #define dbg_check_cats(c) 0 - #define dbg_check_ltab(c) 0 - #define dbg_check_synced_i_size(inode) 0 - #define dbg_check_dir_size(c, dir) 0 - #define dbg_check_tnc(c, x) 0 - #define dbg_check_idx_size(c, idx_size) 0 - #define dbg_check_filesystem(c) 0 - #define dbg_check_heap(c, heap, cat, add_pos) ({}) - #define dbg_check_lprops(c) 0 #define dbg_check_lpt_nodes(c, cnode, row, col) 0 - #define dbg_force_in_the_gaps_enabled 0 #define dbg_force_in_the_gaps() 0 - #define dbg_failure_mode 0 #define dbg_failure_mode_registration(c) ({}) #define dbg_failure_mode_deregistration(c) ({}) -- GitLab From 5acd6ff8ac09eb71f3aef2ccccefab658be8aff4 Mon Sep 17 00:00:00 2001 From: Zoltan Sogor Date: Tue, 12 Aug 2008 13:54:54 +0300 Subject: [PATCH 207/750] UBIFS: fix budgeting request alignment in xattr code Data length has to be aligned in the budgeting request. Code in xattr.c did not do this. Signed-off-by: Zoltan Sogor Signed-off-by: Artem Bityutskiy --- fs/ubifs/xattr.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/fs/ubifs/xattr.c b/fs/ubifs/xattr.c index 39e831d074c..6f493dea561 100644 --- a/fs/ubifs/xattr.c +++ b/fs/ubifs/xattr.c @@ -103,8 +103,8 @@ static int create_xattr(struct ubifs_info *c, struct inode *host, struct inode *inode; struct ubifs_inode *ui, *host_ui = ubifs_inode(host); struct ubifs_budget_req req = { .new_ino = 1, .new_dent = 1, - .new_ino_d = size, .dirtied_ino = 1, - .dirtied_ino_d = ALIGN(host_ui->data_len, 8)}; + .new_ino_d = ALIGN(size, 8), .dirtied_ino = 1, + .dirtied_ino_d = ALIGN(host_ui->data_len, 8) }; if (host_ui->xattr_cnt >= MAX_XATTRS_PER_INODE) return -ENOSPC; @@ -200,7 +200,7 @@ static int change_xattr(struct ubifs_info *c, struct inode *host, struct ubifs_inode *host_ui = ubifs_inode(host); struct ubifs_inode *ui = ubifs_inode(inode); struct ubifs_budget_req req = { .dirtied_ino = 2, - .dirtied_ino_d = size + host_ui->data_len }; + .dirtied_ino_d = ALIGN(size, 8) + ALIGN(host_ui->data_len, 8) }; ubifs_assert(ui->data_len == inode->i_size); err = ubifs_budget_space(c, &req); @@ -497,8 +497,8 @@ static int remove_xattr(struct ubifs_info *c, struct inode *host, int err; struct ubifs_inode *host_ui = ubifs_inode(host); struct ubifs_inode *ui = ubifs_inode(inode); - struct ubifs_budget_req req = { .dirtied_ino = 1, .mod_dent = 1, - .dirtied_ino_d = host_ui->data_len }; + struct ubifs_budget_req req = { .dirtied_ino = 2, .mod_dent = 1, + .dirtied_ino_d = ALIGN(host_ui->data_len, 8) }; ubifs_assert(ui->data_len == inode->i_size); -- GitLab From 5e0115e500fe9dd2ca11e6f92db9123204f1327a Mon Sep 17 00:00:00 2001 From: Brian Haley Date: Wed, 13 Aug 2008 01:58:57 -0700 Subject: [PATCH 208/750] ipv6: Fix OOPS, ip -f inet6 route get fec0::1, linux-2.6.26, ip6_route_output, rt6_fill_node+0x175 Alexey Dobriyan wrote: > On Thu, Aug 07, 2008 at 07:00:56PM +0200, John Gumb wrote: >> Scenario: no ipv6 default route set. > >> # ip -f inet6 route get fec0::1 >> >> BUG: unable to handle kernel NULL pointer dereference at 00000000 >> IP: [] rt6_fill_node+0x175/0x3b0 >> EIP is at rt6_fill_node+0x175/0x3b0 > > 0xffffffff80424dd3 is in rt6_fill_node (net/ipv6/route.c:2191). > 2186 } else > 2187 #endif > 2188 NLA_PUT_U32(skb, RTA_IIF, iif); > 2189 } else if (dst) { > 2190 struct in6_addr saddr_buf; > 2191 ====> if (ipv6_dev_get_saddr(ip6_dst_idev(&rt->u.dst)->dev, > ^^^^^^^^^^^^^^^^^^^^^^^^ > NULL > > 2192 dst, 0, &saddr_buf) == 0) > 2193 NLA_PUT(skb, RTA_PREFSRC, 16, &saddr_buf); > 2194 } The commit that changed this can't be reverted easily, but the patch below works for me. Fix NULL de-reference in rt6_fill_node() when there's no IPv6 input device present in the dst entry. Signed-off-by: Brian Haley Signed-off-by: David S. Miller --- net/ipv6/route.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/net/ipv6/route.c b/net/ipv6/route.c index 5a3e87e4b18..41b165ffb36 100644 --- a/net/ipv6/route.c +++ b/net/ipv6/route.c @@ -2187,8 +2187,9 @@ static int rt6_fill_node(struct sk_buff *skb, struct rt6_info *rt, #endif NLA_PUT_U32(skb, RTA_IIF, iif); } else if (dst) { + struct inet6_dev *idev = ip6_dst_idev(&rt->u.dst); struct in6_addr saddr_buf; - if (ipv6_dev_get_saddr(ip6_dst_idev(&rt->u.dst)->dev, + if (ipv6_dev_get_saddr(idev ? idev->dev : NULL, dst, 0, &saddr_buf) == 0) NLA_PUT(skb, RTA_PREFSRC, 16, &saddr_buf); } -- GitLab From 83f36f3f35f4f83fa346bfff58a5deabc78370e5 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Wed, 13 Aug 2008 02:13:34 -0700 Subject: [PATCH 209/750] pkt_sched: Add queue stopped test back to qdisc_run(). Based upon a bug report by Andrew Gallatin on netdev with subject "CPU utilization increased in 2.6.27rc" In commit 37437bb2e1ae8af470dfcd5b4ff454110894ccaf ("pkt_sched: Schedule qdiscs instead of netdev_queue.") the test of the queue being stopped was erroneously removed from qdisc_run(). When the TX queue of the device fills up, this omission causes lots of extraneous useless work to be queued up to softirq context, where we'll just return immediately because the device is still stuffed up. Signed-off-by: David S. Miller --- include/net/pkt_sched.h | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/include/net/pkt_sched.h b/include/net/pkt_sched.h index 6affcfaa123..853fe83d9f3 100644 --- a/include/net/pkt_sched.h +++ b/include/net/pkt_sched.h @@ -89,7 +89,10 @@ extern void __qdisc_run(struct Qdisc *q); static inline void qdisc_run(struct Qdisc *q) { - if (!test_and_set_bit(__QDISC_STATE_RUNNING, &q->state)) + struct netdev_queue *txq = q->dev_queue; + + if (!netif_tx_queue_stopped(txq) && + !test_and_set_bit(__QDISC_STATE_RUNNING, &q->state)) __qdisc_run(q); } -- GitLab From 6ced0b3f1e1c089caf8798485423a093744b6a48 Mon Sep 17 00:00:00 2001 From: Andrew Morton Date: Wed, 13 Aug 2008 02:32:06 -0700 Subject: [PATCH 210/750] net/tipc/subscr.c: don't use ___constant_swab32 It's an internal implementation detail which we _should_ be free to change. So we did, and it promptly broke. The compiler shold be able to work out when to use the __constant version anyway. Signed-off-by: Andrew Morton Signed-off-by: David S. Miller --- net/tipc/subscr.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/tipc/subscr.c b/net/tipc/subscr.c index 0326d3060bc..0747d8a9232 100644 --- a/net/tipc/subscr.c +++ b/net/tipc/subscr.c @@ -85,7 +85,7 @@ static struct top_srv topsrv = { 0 }; static u32 htohl(u32 in, int swap) { - return swap ? (u32)___constant_swab32(in) : in; + return swap ? swab32(in) : in; } /** -- GitLab From 83ac794f15d2311d8e9e641c73618011f2f7f0a1 Mon Sep 17 00:00:00 2001 From: Rami Rosen Date: Wed, 13 Aug 2008 02:34:39 -0700 Subject: [PATCH 211/750] ipv6: ip6_route.h cleanup. This patch removes rt6_lock declaration from include/net/ip6_route.h as it is unused. Signed-off-by: Rami Rosen Signed-off-by: David S. Miller --- include/net/ip6_route.h | 1 - 1 file changed, 1 deletion(-) diff --git a/include/net/ip6_route.h b/include/net/ip6_route.h index 2f8b3c06a10..49d085649cc 100644 --- a/include/net/ip6_route.h +++ b/include/net/ip6_route.h @@ -118,7 +118,6 @@ extern int rt6_dump_route(struct rt6_info *rt, void *p_arg); extern void rt6_ifdown(struct net *net, struct net_device *dev); extern void rt6_mtu_change(struct net_device *dev, unsigned mtu); -extern rwlock_t rt6_lock; /* * Store a destination cache entry in a socket -- GitLab From 6bf90b2bf4084a64bbcf96a0b93dc64c77288028 Mon Sep 17 00:00:00 2001 From: Rami Rosen Date: Wed, 13 Aug 2008 02:35:39 -0700 Subject: [PATCH 212/750] ipv6: Kill unused ip6_prohibit_entry and ip6_blk_hole_entry declarations. This patch removes ip6_prohibit_entry and ip6_blk_hole_entry declarations from include/net/ip6_route.h as they are unused. Signed-off-by: Rami Rosen Signed-off-by: David S. Miller --- include/net/ip6_route.h | 5 ----- 1 file changed, 5 deletions(-) diff --git a/include/net/ip6_route.h b/include/net/ip6_route.h index 49d085649cc..bc391ba101e 100644 --- a/include/net/ip6_route.h +++ b/include/net/ip6_route.h @@ -38,11 +38,6 @@ struct route_info { #define RT6_LOOKUP_F_SRCPREF_COA 0x00000020 -#ifdef CONFIG_IPV6_MULTIPLE_TABLES -extern struct rt6_info *ip6_prohibit_entry; -extern struct rt6_info *ip6_blk_hole_entry; -#endif - extern void ip6_route_input(struct sk_buff *skb); extern struct dst_entry * ip6_route_output(struct net *net, -- GitLab From 317900cb010f4aca0e3cb14a02d0ddcc44ddafa7 Mon Sep 17 00:00:00 2001 From: Jamal Hadi Salim Date: Wed, 13 Aug 2008 02:39:56 -0700 Subject: [PATCH 213/750] wext: Send name on events In the minimal the wireless extensions oughta send at least the name in addition to the ifindex. Signed-off-by: Jamal Hadi Salim Signed-off-by: David S. Miller --- net/wireless/wext.c | 1 + 1 file changed, 1 insertion(+) diff --git a/net/wireless/wext.c b/net/wireless/wext.c index df5b3886c36..d98ffb75119 100644 --- a/net/wireless/wext.c +++ b/net/wireless/wext.c @@ -1277,6 +1277,7 @@ static int rtnetlink_fill_iwinfo(struct sk_buff *skb, struct net_device *dev, r->ifi_flags = dev_get_flags(dev); r->ifi_change = 0; /* Wireless changes don't affect those flags */ + NLA_PUT_STRING(skb, IFLA_IFNAME, dev->name); /* Add the wireless events in the netlink packet */ NLA_PUT(skb, IFLA_WIRELESS, event_len, event); -- GitLab From 34093d055e09d1bb549efc11c8d448373437bbe4 Mon Sep 17 00:00:00 2001 From: Julien Brunel Date: Wed, 13 Aug 2008 02:40:48 -0700 Subject: [PATCH 214/750] net/rxrpc: Use an IS_ERR test rather than a NULL test In case of error, the function rxrpc_get_transport returns an ERR pointer, but never returns a NULL pointer. So after a call to this function, a NULL test should be replaced by an IS_ERR test. A simplified version of the semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // @correct_null_test@ expression x,E; statement S1, S2; @@ x = rxrpc_get_transport(...) <... when != x = E if ( ( - x@p2 != NULL + ! IS_ERR ( x ) | - x@p2 == NULL + IS_ERR( x ) ) ) S1 else S2 ...> ? x = E; // Signed-off-by: Julien Brunel Signed-off-by: Julia Lawall Signed-off-by: David S. Miller --- net/rxrpc/ar-accept.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/rxrpc/ar-accept.c b/net/rxrpc/ar-accept.c index bdfb7741779..77228f28fa3 100644 --- a/net/rxrpc/ar-accept.c +++ b/net/rxrpc/ar-accept.c @@ -100,7 +100,7 @@ static int rxrpc_accept_incoming_call(struct rxrpc_local *local, trans = rxrpc_get_transport(local, peer, GFP_NOIO); rxrpc_put_peer(peer); - if (!trans) { + if (IS_ERR(trans)) { _debug("no trans"); ret = -EBUSY; goto error; -- GitLab From 55546ac45dfb4087437bedaed43400630c96680e Mon Sep 17 00:00:00 2001 From: Michael Hennerich Date: Wed, 13 Aug 2008 17:41:13 +0800 Subject: [PATCH 215/750] Blackfin arch: workaround SIC_IWR1 reset bug, by keeping MDMA0/1 always enabled in SIC_IWR1. This way we ensure that reboot succeeds. Signed-off-by: Michael Hennerich Signed-off-by: Bryan Wu --- arch/blackfin/mach-common/ints-priority.c | 9 +++++++++ arch/blackfin/mach-common/pm.c | 9 +++++++++ 2 files changed, 18 insertions(+) diff --git a/arch/blackfin/mach-common/ints-priority.c b/arch/blackfin/mach-common/ints-priority.c index 4271ef3f201..7f9df4ee734 100644 --- a/arch/blackfin/mach-common/ints-priority.c +++ b/arch/blackfin/mach-common/ints-priority.c @@ -1069,7 +1069,16 @@ int __init init_arch_irq(void) #if defined(CONFIG_BF54x) || defined(CONFIG_BF52x) || defined(CONFIG_BF561) bfin_write_SIC_IWR0(IWR_DISABLE_ALL); +#if defined(CONFIG_BF52x) + /* BF52x system reset does not properly reset SIC_IWR1 which + * will screw up the bootrom as it relies on MDMA0/1 waking it + * up from IDLE instructions. See this report for more info: + * http://blackfin.uclinux.org/gf/tracker/4323 + */ + bfin_write_SIC_IWR1(IWR_ENABLE(10) | IWR_ENABLE(11)); +#else bfin_write_SIC_IWR1(IWR_DISABLE_ALL); +#endif # ifdef CONFIG_BF54x bfin_write_SIC_IWR2(IWR_DISABLE_ALL); # endif diff --git a/arch/blackfin/mach-common/pm.c b/arch/blackfin/mach-common/pm.c index a17ace3e0e4..e28c6af1f41 100644 --- a/arch/blackfin/mach-common/pm.c +++ b/arch/blackfin/mach-common/pm.c @@ -84,7 +84,16 @@ void bfin_pm_suspend_standby_enter(void) #if defined(CONFIG_BF54x) || defined(CONFIG_BF52x) || defined(CONFIG_BF561) bfin_write_SIC_IWR0(IWR_DISABLE_ALL); +#if defined(CONFIG_BF52x) + /* BF52x system reset does not properly reset SIC_IWR1 which + * will screw up the bootrom as it relies on MDMA0/1 waking it + * up from IDLE instructions. See this report for more info: + * http://blackfin.uclinux.org/gf/tracker/4323 + */ + bfin_write_SIC_IWR1(IWR_ENABLE(10) | IWR_ENABLE(11)); +#else bfin_write_SIC_IWR1(IWR_DISABLE_ALL); +#endif # ifdef CONFIG_BF54x bfin_write_SIC_IWR2(IWR_DISABLE_ALL); # endif -- GitLab From f97017cdefefdb6a0e19266024b0c6f9fd411eeb Mon Sep 17 00:00:00 2001 From: Jamal Hadi Salim Date: Wed, 13 Aug 2008 02:41:22 -0700 Subject: [PATCH 216/750] net-sched: Fix actions flushing Flushing of actions has been broken since we changed the semantics of netlink parsed tb[X] to mean X is an attribute type. This makes the flushing work. Signed-off-by: Jamal Hadi Salim Signed-off-by: David S. Miller --- net/sched/act_api.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) diff --git a/net/sched/act_api.c b/net/sched/act_api.c index 26c7e1f9a35..88b57331d13 100644 --- a/net/sched/act_api.c +++ b/net/sched/act_api.c @@ -790,6 +790,8 @@ static int tca_action_flush(struct nlattr *nla, struct nlmsghdr *n, u32 pid) err = a->ops->walk(skb, &dcb, RTM_DELACTION, a); if (err < 0) goto nla_put_failure; + if (err == 0) + goto noflush_out; nla_nest_end(skb, nest); @@ -807,6 +809,7 @@ nla_put_failure: nlmsg_failure: module_put(a->ops->owner); err_out: +noflush_out: kfree_skb(skb); kfree(a); return err; @@ -824,8 +827,10 @@ tca_action_gd(struct nlattr *nla, struct nlmsghdr *n, u32 pid, int event) return ret; if (event == RTM_DELACTION && n->nlmsg_flags&NLM_F_ROOT) { - if (tb[0] != NULL && tb[1] == NULL) - return tca_action_flush(tb[0], n, pid); + if (tb[1] != NULL) + return tca_action_flush(tb[1], n, pid); + else + return -EINVAL; } for (i = 1; i <= TCA_ACT_MAX_PRIO && tb[i]; i++) { -- GitLab From 36723873b664fb6b5cfe06d291df948126e43f50 Mon Sep 17 00:00:00 2001 From: Jamal Hadi Salim Date: Wed, 13 Aug 2008 02:41:45 -0700 Subject: [PATCH 217/750] net-sched: fix Action flushing return code Flushing must consistently return ENOMEM on failure of any allocation Signed-off-by: Jamal Hadi Salim Signed-off-by: David S. Miller --- net/sched/act_api.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/net/sched/act_api.c b/net/sched/act_api.c index 88b57331d13..9974b3f04f0 100644 --- a/net/sched/act_api.c +++ b/net/sched/act_api.c @@ -751,7 +751,7 @@ static int tca_action_flush(struct nlattr *nla, struct nlmsghdr *n, u32 pid) struct nlattr *tb[TCA_ACT_MAX+1]; struct nlattr *kind; struct tc_action *a = create_a(0); - int err = -EINVAL; + int err = -ENOMEM; if (a == NULL) { printk("tca_action_flush: couldnt create tc_action\n"); @@ -762,7 +762,7 @@ static int tca_action_flush(struct nlattr *nla, struct nlmsghdr *n, u32 pid) if (!skb) { printk("tca_action_flush: failed skb alloc\n"); kfree(a); - return -ENOBUFS; + return err; } b = skb_tail_pointer(skb); -- GitLab From 0ed89b06e49c326bff81d81f24b9ba955eb912d5 Mon Sep 17 00:00:00 2001 From: Johannes Weiner Date: Wed, 13 Aug 2008 10:17:24 +0200 Subject: [PATCH 218/750] x86: propagate new nonpanic bootmem macros to CONFIG_HAVE_ARCH_BOOTMEM_NODE Commit 74768ed833344b "page allocator: use no-panic variant of alloc_bootmem() in alloc_large_system_hash()" introduced two new _nopanic macros which are undefined for CONFIG_HAVE_ARCH_BOOTMEM_NODE. Signed-off-by: Johannes Weiner Acked-by: "Jan Beulich" Signed-off-by: Ingo Molnar --- include/asm-x86/mmzone_32.h | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/include/asm-x86/mmzone_32.h b/include/asm-x86/mmzone_32.h index b2298a22756..5862e646065 100644 --- a/include/asm-x86/mmzone_32.h +++ b/include/asm-x86/mmzone_32.h @@ -97,10 +97,16 @@ static inline int pfn_valid(int pfn) reserve_bootmem_node(NODE_DATA(0), (addr), (size), (flags)) #define alloc_bootmem(x) \ __alloc_bootmem_node(NODE_DATA(0), (x), SMP_CACHE_BYTES, __pa(MAX_DMA_ADDRESS)) +#define alloc_bootmem_nopanic(x) \ + __alloc_bootmem_node_nopanic(NODE_DATA(0), (x), SMP_CACHE_BYTES, \ + __pa(MAX_DMA_ADDRESS)) #define alloc_bootmem_low(x) \ __alloc_bootmem_node(NODE_DATA(0), (x), SMP_CACHE_BYTES, 0) #define alloc_bootmem_pages(x) \ __alloc_bootmem_node(NODE_DATA(0), (x), PAGE_SIZE, __pa(MAX_DMA_ADDRESS)) +#define alloc_bootmem_pages_nopanic(x) \ + __alloc_bootmem_node_nopanic(NODE_DATA(0), (x), PAGE_SIZE, \ + __pa(MAX_DMA_ADDRESS)) #define alloc_bootmem_low_pages(x) \ __alloc_bootmem_node(NODE_DATA(0), (x), PAGE_SIZE, 0) #define alloc_bootmem_node(pgdat, x) \ -- GitLab From 7b27718bdb1b70166383dec91391df5534d449ee Mon Sep 17 00:00:00 2001 From: Joerg Roedel Date: Wed, 13 Aug 2008 10:07:05 +0200 Subject: [PATCH 219/750] x86: fix setup code crashes on my old 486 box yesterday I tried to reactivate my old 486 box and wanted to install a current Linux with latest kernel on it. But it turned out that the latest kernel does not boot because the machine crashes early in the setup code. After some debugging it turned out that the problem is the query_ist() function. If this interrupt with that function is called the machine simply locks up. It looks like a BIOS bug. Looking for a workaround for this problem I wrote the attached patch. It checks for the CPUID instruction and if it is not implemented it does not call the speedstep BIOS function. As far as I know speedstep should be available since some Pentium earliest. Alan Cox observed that it's available since the Pentium II, so cpuid levels 4 and 5 can be excluded altogether. H. Peter Anvin cleaned up the code some more: > Right in concept, but I dislike the implementation (duplication of the > CPU detect code we already have). Could you try this patch and see if > it works for you? which, with a small modification to fix a build error with it the resulting kernel boots on my machine. Signed-off-by: Joerg Roedel Signed-off-by: "H. Peter Anvin" Cc: Signed-off-by: Ingo Molnar --- arch/x86/boot/boot.h | 8 ++++++++ arch/x86/boot/cpucheck.c | 8 +------- arch/x86/boot/main.c | 4 ++++ 3 files changed, 13 insertions(+), 7 deletions(-) diff --git a/arch/x86/boot/boot.h b/arch/x86/boot/boot.h index a34b9982c7c..9d4b4b43d97 100644 --- a/arch/x86/boot/boot.h +++ b/arch/x86/boot/boot.h @@ -25,6 +25,8 @@ #include #include +#define NCAPINTS 8 + /* Useful macros */ #define BUILD_BUG_ON(condition) ((void)sizeof(char[1 - 2*!!(condition)])) @@ -242,6 +244,12 @@ int cmdline_find_option(const char *option, char *buffer, int bufsize); int cmdline_find_option_bool(const char *option); /* cpu.c, cpucheck.c */ +struct cpu_features { + int level; /* Family, or 64 for x86-64 */ + int model; + u32 flags[NCAPINTS]; +}; +extern struct cpu_features cpu; int check_cpu(int *cpu_level_ptr, int *req_level_ptr, u32 **err_flags_ptr); int validate_cpu(void); diff --git a/arch/x86/boot/cpucheck.c b/arch/x86/boot/cpucheck.c index 7804389ee00..c1ce0303d99 100644 --- a/arch/x86/boot/cpucheck.c +++ b/arch/x86/boot/cpucheck.c @@ -30,13 +30,7 @@ #include #include -struct cpu_features { - int level; /* Family, or 64 for x86-64 */ - int model; - u32 flags[NCAPINTS]; -}; - -static struct cpu_features cpu; +struct cpu_features cpu; static u32 cpu_vendor[3]; static u32 err_flags[NCAPINTS]; diff --git a/arch/x86/boot/main.c b/arch/x86/boot/main.c index 2296164b54d..01aa64b5575 100644 --- a/arch/x86/boot/main.c +++ b/arch/x86/boot/main.c @@ -73,6 +73,10 @@ static void keyboard_set_repeat(void) */ static void query_ist(void) { + /* Some 486 BIOSes apparently crash on this call */ + if (cpu.level < 6) + return; + asm("int $0x15" : "=a" (boot_params.ist_info.signature), "=b" (boot_params.ist_info.command), -- GitLab From f3c85bc1bc72b4cc8d58664a490a9d42bdb6565a Mon Sep 17 00:00:00 2001 From: Lee Nipper Date: Wed, 30 Jul 2008 16:26:57 +0800 Subject: [PATCH 220/750] crypto: talitos - Add handling for SEC 3.x treatment of link table Later SEC revision requires the link table (used for scatter/gather) to have an extra entry to account for the total length in descriptor [4], which contains cipher Input and ICV. This only applies to decrypt, not encrypt. Without this change, on 837x, a gather return/length error results when a decryption uses a link table to gather the fragments. This is observed by doing a ping with size of 1447 or larger with AES, or a ping with size 1455 or larger with 3des. So, add check for SEC compatible "fsl,3.0" for using extra link table entry. Signed-off-by: Lee Nipper Signed-off-by: Kim Phillips Signed-off-by: Herbert Xu --- drivers/crypto/talitos.c | 54 +++++++++++++++++++++++++++++----------- 1 file changed, 39 insertions(+), 15 deletions(-) diff --git a/drivers/crypto/talitos.c b/drivers/crypto/talitos.c index 681c15f4208..ee827a7f7c6 100644 --- a/drivers/crypto/talitos.c +++ b/drivers/crypto/talitos.c @@ -96,6 +96,9 @@ struct talitos_private { unsigned int exec_units; unsigned int desc_types; + /* SEC Compatibility info */ + unsigned long features; + /* next channel to be assigned next incoming descriptor */ atomic_t last_chan; @@ -133,6 +136,9 @@ struct talitos_private { struct hwrng rng; }; +/* .features flag */ +#define TALITOS_FTR_SRC_LINK_TBL_LEN_INCLUDES_EXTENT 0x00000001 + /* * map virtual single (contiguous) pointer to h/w descriptor pointer */ @@ -785,7 +791,7 @@ static void ipsec_esp_encrypt_done(struct device *dev, /* copy the generated ICV to dst */ if (edesc->dma_len) { icvdata = &edesc->link_tbl[edesc->src_nents + - edesc->dst_nents + 1]; + edesc->dst_nents + 2]; sg = sg_last(areq->dst, edesc->dst_nents); memcpy((char *)sg_virt(sg) + sg->length - ctx->authsize, icvdata, ctx->authsize); @@ -814,7 +820,7 @@ static void ipsec_esp_decrypt_done(struct device *dev, /* auth check */ if (edesc->dma_len) icvdata = &edesc->link_tbl[edesc->src_nents + - edesc->dst_nents + 1]; + edesc->dst_nents + 2]; else icvdata = &edesc->link_tbl[0]; @@ -921,10 +927,30 @@ static int ipsec_esp(struct ipsec_esp_edesc *edesc, struct aead_request *areq, sg_count = sg_to_link_tbl(areq->src, sg_count, cryptlen, &edesc->link_tbl[0]); if (sg_count > 1) { + struct talitos_ptr *link_tbl_ptr = + &edesc->link_tbl[sg_count-1]; + struct scatterlist *sg; + struct talitos_private *priv = dev_get_drvdata(dev); + desc->ptr[4].j_extent |= DESC_PTR_LNKTBL_JUMP; desc->ptr[4].ptr = cpu_to_be32(edesc->dma_link_tbl); dma_sync_single_for_device(ctx->dev, edesc->dma_link_tbl, edesc->dma_len, DMA_BIDIRECTIONAL); + /* If necessary for this SEC revision, + * add a link table entry for ICV. + */ + if ((priv->features & + TALITOS_FTR_SRC_LINK_TBL_LEN_INCLUDES_EXTENT) && + (edesc->desc.hdr & DESC_HDR_MODE0_ENCRYPT) == 0) { + link_tbl_ptr->j_extent = 0; + link_tbl_ptr++; + link_tbl_ptr->j_extent = DESC_PTR_LNKTBL_RETURN; + link_tbl_ptr->len = cpu_to_be16(authsize); + sg = sg_last(areq->src, edesc->src_nents ? : 1); + link_tbl_ptr->ptr = cpu_to_be32( + (char *)sg_dma_address(sg) + + sg->length - authsize); + } } else { /* Only one segment now, so no link tbl needed */ desc->ptr[4].ptr = cpu_to_be32(sg_dma_address(areq->src)); @@ -944,12 +970,11 @@ static int ipsec_esp(struct ipsec_esp_edesc *edesc, struct aead_request *areq, desc->ptr[5].ptr = cpu_to_be32(sg_dma_address(areq->dst)); } else { struct talitos_ptr *link_tbl_ptr = - &edesc->link_tbl[edesc->src_nents]; - struct scatterlist *sg; + &edesc->link_tbl[edesc->src_nents + 1]; desc->ptr[5].ptr = cpu_to_be32((struct talitos_ptr *) edesc->dma_link_tbl + - edesc->src_nents); + edesc->src_nents + 1); if (areq->src == areq->dst) { memcpy(link_tbl_ptr, &edesc->link_tbl[0], edesc->src_nents * sizeof(struct talitos_ptr)); @@ -957,14 +982,10 @@ static int ipsec_esp(struct ipsec_esp_edesc *edesc, struct aead_request *areq, sg_count = sg_to_link_tbl(areq->dst, sg_count, cryptlen, link_tbl_ptr); } + /* Add an entry to the link table for ICV data */ link_tbl_ptr += sg_count - 1; - - /* handle case where sg_last contains the ICV exclusively */ - sg = sg_last(areq->dst, edesc->dst_nents); - if (sg->length == ctx->authsize) - link_tbl_ptr--; - link_tbl_ptr->j_extent = 0; + sg_count++; link_tbl_ptr++; link_tbl_ptr->j_extent = DESC_PTR_LNKTBL_RETURN; link_tbl_ptr->len = cpu_to_be16(authsize); @@ -973,7 +994,7 @@ static int ipsec_esp(struct ipsec_esp_edesc *edesc, struct aead_request *areq, link_tbl_ptr->ptr = cpu_to_be32((struct talitos_ptr *) edesc->dma_link_tbl + edesc->src_nents + - edesc->dst_nents + 1); + edesc->dst_nents + 2); desc->ptr[5].j_extent |= DESC_PTR_LNKTBL_JUMP; dma_sync_single_for_device(ctx->dev, edesc->dma_link_tbl, @@ -1040,12 +1061,12 @@ static struct ipsec_esp_edesc *ipsec_esp_edesc_alloc(struct aead_request *areq, /* * allocate space for base edesc plus the link tables, - * allowing for a separate entry for the generated ICV (+ 1), + * allowing for two separate entries for ICV and generated ICV (+ 2), * and the ICV data itself */ alloc_len = sizeof(struct ipsec_esp_edesc); if (src_nents || dst_nents) { - dma_len = (src_nents + dst_nents + 1) * + dma_len = (src_nents + dst_nents + 2) * sizeof(struct talitos_ptr) + ctx->authsize; alloc_len += dma_len; } else { @@ -1104,7 +1125,7 @@ static int aead_authenc_decrypt(struct aead_request *req) /* stash incoming ICV for later cmp with ICV generated by the h/w */ if (edesc->dma_len) icvdata = &edesc->link_tbl[edesc->src_nents + - edesc->dst_nents + 1]; + edesc->dst_nents + 2]; else icvdata = &edesc->link_tbl[0]; @@ -1480,6 +1501,9 @@ static int talitos_probe(struct of_device *ofdev, goto err_out; } + if (of_device_is_compatible(np, "fsl,sec3.0")) + priv->features |= TALITOS_FTR_SRC_LINK_TBL_LEN_INCLUDES_EXTENT; + priv->head_lock = kmalloc(sizeof(spinlock_t) * priv->num_channels, GFP_KERNEL); priv->tail_lock = kmalloc(sizeof(spinlock_t) * priv->num_channels, -- GitLab From f176e632efad33aeb2d3c5ddfa86861c0d60553c Mon Sep 17 00:00:00 2001 From: Herbert Xu Date: Wed, 30 Jul 2008 16:23:51 +0800 Subject: [PATCH 221/750] crypto: tcrypt - Fix AEAD chunk testing My changeset 4b22f0ddb6564210c9ded7ba25b2a1007733e784 crypto: tcrpyt - Remove unnecessary kmap/kunmap calls introduced a typo that broke AEAD chunk testing. In particular, axbuf should really be xbuf. There is also an issue with testing the last segment when encrypting. The additional part produced by AEAD wasn't tested. Similarly, on decryption the additional part of the AEAD input is mistaken for corruption. Signed-off-by: Herbert Xu --- crypto/tcrypt.c | 28 +++++++++++++++++++--------- 1 file changed, 19 insertions(+), 9 deletions(-) diff --git a/crypto/tcrypt.c b/crypto/tcrypt.c index 59821a22d75..66368022e0b 100644 --- a/crypto/tcrypt.c +++ b/crypto/tcrypt.c @@ -481,21 +481,31 @@ next_one: for (k = 0, temp = 0; k < template[i].np; k++) { printk(KERN_INFO "page %u\n", k); - q = &axbuf[IDX[k]]; - hexdump(q, template[i].tap[k]); + q = &xbuf[IDX[k]]; + + n = template[i].tap[k]; + if (k == template[i].np - 1) + n += enc ? authsize : -authsize; + hexdump(q, n); printk(KERN_INFO "%s\n", - memcmp(q, template[i].result + temp, - template[i].tap[k] - - (k < template[i].np - 1 || enc ? - 0 : authsize)) ? + memcmp(q, template[i].result + temp, n) ? "fail" : "pass"); - for (n = 0; q[template[i].tap[k] + n]; n++) - ; + q += n; + if (k == template[i].np - 1 && !enc) { + if (memcmp(q, template[i].input + + temp + n, authsize)) + n = authsize; + else + n = 0; + } else { + for (n = 0; q[n]; n++) + ; + } if (n) { printk("Result buffer corruption %u " "bytes:\n", n); - hexdump(&q[template[i].tap[k]], n); + hexdump(q, n); } temp += template[i].tap[k]; -- GitLab From dbaaba1d0abf6871c7db6e3d15a46206bc386db1 Mon Sep 17 00:00:00 2001 From: Herbert Xu Date: Sun, 3 Aug 2008 21:19:43 +0800 Subject: [PATCH 222/750] crypto: hash - Fix digest size check for digest type The changeset ca786dc738f4f583b57b1bba7a335b5e8233f4b0 crypto: hash - Fixed digest size check missed one spot for the digest type. This patch corrects that error. Signed-off-by: Herbert Xu --- crypto/digest.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/crypto/digest.c b/crypto/digest.c index ac0919460d1..5d3f1303da9 100644 --- a/crypto/digest.c +++ b/crypto/digest.c @@ -225,7 +225,7 @@ int crypto_init_digest_ops_async(struct crypto_tfm *tfm) struct ahash_tfm *crt = &tfm->crt_ahash; struct digest_alg *dalg = &tfm->__crt_alg->cra_digest; - if (dalg->dia_digestsize > crypto_tfm_alg_blocksize(tfm)) + if (dalg->dia_digestsize > PAGE_SIZE / 8) return -EINVAL; crt->init = digest_async_init; -- GitLab From 318e5313923197e71a94f7b18835151649384b7f Mon Sep 17 00:00:00 2001 From: Herbert Xu Date: Tue, 5 Aug 2008 13:34:30 +0800 Subject: [PATCH 223/750] crypto: hash - Add missing top-level functions The top-level functions init/update/final were missing for ahash. Signed-off-by: Herbert Xu --- include/crypto/hash.h | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) diff --git a/include/crypto/hash.h b/include/crypto/hash.h index d12498ec8a4..ee48ef8fb2e 100644 --- a/include/crypto/hash.h +++ b/include/crypto/hash.h @@ -101,6 +101,24 @@ static inline int crypto_ahash_digest(struct ahash_request *req) return crt->digest(req); } +static inline int crypto_ahash_init(struct ahash_request *req) +{ + struct ahash_tfm *crt = crypto_ahash_crt(crypto_ahash_reqtfm(req)); + return crt->init(req); +} + +static inline int crypto_ahash_update(struct ahash_request *req) +{ + struct ahash_tfm *crt = crypto_ahash_crt(crypto_ahash_reqtfm(req)); + return crt->update(req); +} + +static inline int crypto_ahash_final(struct ahash_request *req) +{ + struct ahash_tfm *crt = crypto_ahash_crt(crypto_ahash_reqtfm(req)); + return crt->final(req); +} + static inline void ahash_request_set_tfm(struct ahash_request *req, struct crypto_ahash *tfm) { -- GitLab From d6672c501852d577097f6757c311d937aca0b04b Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Fri, 1 Aug 2008 11:23:50 +0200 Subject: [PATCH 224/750] lockdep: build fix fix: kernel/built-in.o: In function `lockdep_stats_show': lockdep_proc.c:(.text+0x3cb2f): undefined reference to `lockdep_count_forward_deps' kernel/built-in.o: In function `l_show': lockdep_proc.c:(.text+0x3d02b): undefined reference to `lockdep_count_forward_deps' lockdep_proc.c:(.text+0x3d047): undefined reference to `lockdep_count_backward_deps' Signed-off-by: Ingo Molnar --- kernel/lockdep_internals.h | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/kernel/lockdep_internals.h b/kernel/lockdep_internals.h index 55db193d366..56b196932c0 100644 --- a/kernel/lockdep_internals.h +++ b/kernel/lockdep_internals.h @@ -50,8 +50,21 @@ extern unsigned int nr_process_chains; extern unsigned int max_lockdep_depth; extern unsigned int max_recursion_depth; +#ifdef CONFIG_PROVE_LOCKING extern unsigned long lockdep_count_forward_deps(struct lock_class *); extern unsigned long lockdep_count_backward_deps(struct lock_class *); +#else +static inline unsigned long +lockdep_count_forward_deps(struct lock_class *class) +{ + return 0; +} +static inline unsigned long +lockdep_count_backward_deps(struct lock_class *class) +{ + return 0; +} +#endif #ifdef CONFIG_DEBUG_LOCKDEP /* -- GitLab From c9d08f0860d47ed6a3fe91d0f19335086179be7b Mon Sep 17 00:00:00 2001 From: Marcin Slusarz Date: Tue, 12 Aug 2008 23:23:03 +0200 Subject: [PATCH 225/750] x86: fix 2 section mismatch warnings - map_high() WARNING: vmlinux.o(.text+0x14cf8): Section mismatch in reference from the function map_high() to the function .init.text:init_extra_mapping_uc() The function map_high() references the function __init init_extra_mapping_uc(). This is often because map_high lacks a __init annotation or the annotation of init_extra_mapping_uc is wrong. WARNING: vmlinux.o(.text+0x14d05): Section mismatch in reference from the function map_high() to the function .init.text:init_extra_mapping_wb() The function map_high() references the function __init init_extra_mapping_wb(). This is often because map_high lacks a __init annotation or the annotation of init_extra_mapping_wb is wrong. map_high is called only from __init functions (map_*_high) and calls 2 __init_functions (init_extra_mapping_*) Signed-off-by: Marcin Slusarz Signed-off-by: Ingo Molnar --- arch/x86/kernel/genx2apic_uv_x.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/genx2apic_uv_x.c b/arch/x86/kernel/genx2apic_uv_x.c index 2cfcbded888..2d7e307c777 100644 --- a/arch/x86/kernel/genx2apic_uv_x.c +++ b/arch/x86/kernel/genx2apic_uv_x.c @@ -222,7 +222,7 @@ static __init void map_low_mmrs(void) enum map_type {map_wb, map_uc}; -static void map_high(char *id, unsigned long base, int shift, enum map_type map_type) +static __init void map_high(char *id, unsigned long base, int shift, enum map_type map_type) { unsigned long bytes, paddr; -- GitLab From c72f4573a5e05e35a31474977f500cbe21dcbb11 Mon Sep 17 00:00:00 2001 From: Andrew Morton Date: Tue, 12 Aug 2008 13:27:37 -0700 Subject: [PATCH 226/750] lockdep: spin_lock_nest_lock(), checkpatch fixes fix: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable #46: FILE: kernel/spinlock.c:326: +EXPORT_SYMBOL(_spin_lock_nest_lock); total: 0 errors, 1 warnings, 26 lines checked Signed-off-by: Andrew Morton Signed-off-by: Peter Zijlstra Signed-off-by: Ingo Molnar --- kernel/spinlock.c | 3 --- 1 file changed, 3 deletions(-) diff --git a/kernel/spinlock.c b/kernel/spinlock.c index 44baeea94ab..29ab20749dd 100644 --- a/kernel/spinlock.c +++ b/kernel/spinlock.c @@ -290,7 +290,6 @@ void __lockfunc _spin_lock_nested(spinlock_t *lock, int subclass) spin_acquire(&lock->dep_map, subclass, 0, _RET_IP_); LOCK_CONTENDED(lock, _raw_spin_trylock, _raw_spin_lock); } - EXPORT_SYMBOL(_spin_lock_nested); unsigned long __lockfunc _spin_lock_irqsave_nested(spinlock_t *lock, int subclass) @@ -312,7 +311,6 @@ unsigned long __lockfunc _spin_lock_irqsave_nested(spinlock_t *lock, int subclas #endif return flags; } - EXPORT_SYMBOL(_spin_lock_irqsave_nested); void __lockfunc _spin_lock_nest_lock(spinlock_t *lock, @@ -322,7 +320,6 @@ void __lockfunc _spin_lock_nest_lock(spinlock_t *lock, spin_acquire_nest(&lock->dep_map, 0, 0, nest_lock, _RET_IP_); LOCK_CONTENDED(lock, _raw_spin_trylock, _raw_spin_lock); } - EXPORT_SYMBOL(_spin_lock_nest_lock); #endif -- GitLab From e49140120c88eb99db1a9172d9ac224c0f2bbdd2 Mon Sep 17 00:00:00 2001 From: Suresh Siddha Date: Wed, 13 Aug 2008 22:02:26 +1000 Subject: [PATCH 227/750] crypto: padlock - fix VIA PadLock instruction usage with irq_ts_save/restore() Wolfgang Walter reported this oops on his via C3 using padlock for AES-encryption: ################################################################## BUG: unable to handle kernel NULL pointer dereference at 000001f0 IP: [] __switch_to+0x30/0x117 *pde = 00000000 Oops: 0002 [#1] PREEMPT Modules linked in: Pid: 2071, comm: sleep Not tainted (2.6.26 #11) EIP: 0060:[] EFLAGS: 00010002 CPU: 0 EIP is at __switch_to+0x30/0x117 EAX: 00000000 EBX: c0493300 ECX: dc48dd00 EDX: c0493300 ESI: dc48dd00 EDI: c0493530 EBP: c04cff8c ESP: c04cff7c DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068 Process sleep (pid: 2071, ti=c04ce000 task=dc48dd00 task.ti=d2fe6000) Stack: dc48df30 c0493300 00000000 00000000 d2fe7f44 c03b5b43 c04cffc8 00000046 c0131856 0000005a dc472d3c c0493300 c0493470 d983ae00 00002696 00000000 c0239f54 00000000 c04c4000 c04cffd8 c01025fe c04f3740 00049800 c04cffe0 Call Trace: [] ? schedule+0x285/0x2ff [] ? pm_qos_requirement+0x3c/0x53 [] ? acpi_processor_idle+0x0/0x434 [] ? cpu_idle+0x73/0x7f [] ? rest_init+0x61/0x63 ======================= Wolfgang also found out that adding kernel_fpu_begin() and kernel_fpu_end() around the padlock instructions fix the oops. Suresh wrote: These padlock instructions though don't use/touch SSE registers, but it behaves similar to other SSE instructions. For example, it might cause DNA faults when cr0.ts is set. While this is a spurious DNA trap, it might cause oops with the recent fpu code changes. This is the code sequence that is probably causing this problem: a) new app is getting exec'd and it is somewhere in between start_thread() and flush_old_exec() in the load_xyz_binary() b) At pont "a", task's fpu state (like TS_USEDFPU, used_math() etc) is cleared. c) Now we get an interrupt/softirq which starts using these encrypt/decrypt routines in the network stack. This generates a math fault (as cr0.ts is '1') which sets TS_USEDFPU and restores the math that is in the task's xstate. d) Return to exec code path, which does start_thread() which does free_thread_xstate() and sets xstate pointer to NULL while the TS_USEDFPU is still set. e) At the next context switch from the new exec'd task to another task, we have a scenarios where TS_USEDFPU is set but xstate pointer is null. This can cause an oops during unlazy_fpu() in __switch_to() Now: 1) This should happen with or with out pre-emption. Viro also encountered similar problem with out CONFIG_PREEMPT. 2) kernel_fpu_begin() and kernel_fpu_end() will fix this problem, because kernel_fpu_begin() will manually do a clts() and won't run in to the situation of setting TS_USEDFPU in step "c" above. 3) This was working before the fpu changes, because its a spurious math fault which doesn't corrupt any fpu/sse registers and the task's math state was always in an allocated state. With out the recent lazy fpu allocation changes, while we don't see oops, there is a possible race still present in older kernels(for example, while kernel is using kernel_fpu_begin() in some optimized clear/copy page and an interrupt/softirq happens which uses these padlock instructions generating DNA fault). This is the failing scenario that existed even before the lazy fpu allocation changes: 0. CPU's TS flag is set 1. kernel using FPU in some optimized copy routine and while doing kernel_fpu_begin() takes an interrupt just before doing clts() 2. Takes an interrupt and ipsec uses padlock instruction. And we take a DNA fault as TS flag is still set. 3. We handle the DNA fault and set TS_USEDFPU and clear cr0.ts 4. We complete the padlock routine 5. Go back to step-1, which resumes clts() in kernel_fpu_begin(), finishes the optimized copy routine and does kernel_fpu_end(). At this point, we have cr0.ts again set to '1' but the task's TS_USEFPU is stilll set and not cleared. 6. Now kernel resumes its user operation. And at the next context switch, kernel sees it has do a FP save as TS_USEDFPU is still set and then will do a unlazy_fpu() in __switch_to(). unlazy_fpu() will take a DNA fault, as cr0.ts is '1' and now, because we are in __switch_to(), math_state_restore() will get confused and will restore the next task's FP state and will save it in prev tasks's FP state. Remember, in __switch_to() we are already on the stack of the next task but take a DNA fault for the prev task. This causes the fpu leakage. Fix the padlock instruction usage by calling them inside the context of new routines irq_ts_save/restore(), which clear/restore cr0.ts manually in the interrupt context. This will not generate spurious DNA in the context of the interrupt which will fix the oops encountered and the possible FPU leakage issue. Reported-and-bisected-by: Wolfgang Walter Signed-off-by: Suresh Siddha Signed-off-by: Herbert Xu --- drivers/char/hw_random/via-rng.c | 8 ++++++++ drivers/crypto/padlock-aes.c | 28 +++++++++++++++++++++++++++- drivers/crypto/padlock-sha.c | 9 +++++++++ include/asm-x86/i387.h | 32 ++++++++++++++++++++++++++++++++ 4 files changed, 76 insertions(+), 1 deletion(-) diff --git a/drivers/char/hw_random/via-rng.c b/drivers/char/hw_random/via-rng.c index f7feae4ebb5..128202e18fc 100644 --- a/drivers/char/hw_random/via-rng.c +++ b/drivers/char/hw_random/via-rng.c @@ -31,6 +31,7 @@ #include #include #include +#include #define PFX KBUILD_MODNAME ": " @@ -67,16 +68,23 @@ enum { * Another possible performance boost may come from simply buffering * until we have 4 bytes, thus returning a u32 at a time, * instead of the current u8-at-a-time. + * + * Padlock instructions can generate a spurious DNA fault, so + * we have to call them in the context of irq_ts_save/restore() */ static inline u32 xstore(u32 *addr, u32 edx_in) { u32 eax_out; + int ts_state; + + ts_state = irq_ts_save(); asm(".byte 0x0F,0xA7,0xC0 /* xstore %%edi (addr=%0) */" :"=m"(*addr), "=a"(eax_out) :"D"(addr), "d"(edx_in)); + irq_ts_restore(ts_state); return eax_out; } diff --git a/drivers/crypto/padlock-aes.c b/drivers/crypto/padlock-aes.c index 54a2a166e56..bf2917d197a 100644 --- a/drivers/crypto/padlock-aes.c +++ b/drivers/crypto/padlock-aes.c @@ -16,6 +16,7 @@ #include #include #include +#include #include "padlock.h" /* Control word. */ @@ -141,6 +142,12 @@ static inline void padlock_reset_key(void) asm volatile ("pushfl; popfl"); } +/* + * While the padlock instructions don't use FP/SSE registers, they + * generate a spurious DNA fault when cr0.ts is '1'. These instructions + * should be used only inside the irq_ts_save/restore() context + */ + static inline void padlock_xcrypt(const u8 *input, u8 *output, void *key, void *control_word) { @@ -205,15 +212,23 @@ static inline u8 *padlock_xcrypt_cbc(const u8 *input, u8 *output, void *key, static void aes_encrypt(struct crypto_tfm *tfm, u8 *out, const u8 *in) { struct aes_ctx *ctx = aes_ctx(tfm); + int ts_state; padlock_reset_key(); + + ts_state = irq_ts_save(); aes_crypt(in, out, ctx->E, &ctx->cword.encrypt); + irq_ts_restore(ts_state); } static void aes_decrypt(struct crypto_tfm *tfm, u8 *out, const u8 *in) { struct aes_ctx *ctx = aes_ctx(tfm); + int ts_state; padlock_reset_key(); + + ts_state = irq_ts_save(); aes_crypt(in, out, ctx->D, &ctx->cword.decrypt); + irq_ts_restore(ts_state); } static struct crypto_alg aes_alg = { @@ -244,12 +259,14 @@ static int ecb_aes_encrypt(struct blkcipher_desc *desc, struct aes_ctx *ctx = blk_aes_ctx(desc->tfm); struct blkcipher_walk walk; int err; + int ts_state; padlock_reset_key(); blkcipher_walk_init(&walk, dst, src, nbytes); err = blkcipher_walk_virt(desc, &walk); + ts_state = irq_ts_save(); while ((nbytes = walk.nbytes)) { padlock_xcrypt_ecb(walk.src.virt.addr, walk.dst.virt.addr, ctx->E, &ctx->cword.encrypt, @@ -257,6 +274,7 @@ static int ecb_aes_encrypt(struct blkcipher_desc *desc, nbytes &= AES_BLOCK_SIZE - 1; err = blkcipher_walk_done(desc, &walk, nbytes); } + irq_ts_restore(ts_state); return err; } @@ -268,12 +286,14 @@ static int ecb_aes_decrypt(struct blkcipher_desc *desc, struct aes_ctx *ctx = blk_aes_ctx(desc->tfm); struct blkcipher_walk walk; int err; + int ts_state; padlock_reset_key(); blkcipher_walk_init(&walk, dst, src, nbytes); err = blkcipher_walk_virt(desc, &walk); + ts_state = irq_ts_save(); while ((nbytes = walk.nbytes)) { padlock_xcrypt_ecb(walk.src.virt.addr, walk.dst.virt.addr, ctx->D, &ctx->cword.decrypt, @@ -281,7 +301,7 @@ static int ecb_aes_decrypt(struct blkcipher_desc *desc, nbytes &= AES_BLOCK_SIZE - 1; err = blkcipher_walk_done(desc, &walk, nbytes); } - + irq_ts_restore(ts_state); return err; } @@ -314,12 +334,14 @@ static int cbc_aes_encrypt(struct blkcipher_desc *desc, struct aes_ctx *ctx = blk_aes_ctx(desc->tfm); struct blkcipher_walk walk; int err; + int ts_state; padlock_reset_key(); blkcipher_walk_init(&walk, dst, src, nbytes); err = blkcipher_walk_virt(desc, &walk); + ts_state = irq_ts_save(); while ((nbytes = walk.nbytes)) { u8 *iv = padlock_xcrypt_cbc(walk.src.virt.addr, walk.dst.virt.addr, ctx->E, @@ -329,6 +351,7 @@ static int cbc_aes_encrypt(struct blkcipher_desc *desc, nbytes &= AES_BLOCK_SIZE - 1; err = blkcipher_walk_done(desc, &walk, nbytes); } + irq_ts_restore(ts_state); return err; } @@ -340,12 +363,14 @@ static int cbc_aes_decrypt(struct blkcipher_desc *desc, struct aes_ctx *ctx = blk_aes_ctx(desc->tfm); struct blkcipher_walk walk; int err; + int ts_state; padlock_reset_key(); blkcipher_walk_init(&walk, dst, src, nbytes); err = blkcipher_walk_virt(desc, &walk); + ts_state = irq_ts_save(); while ((nbytes = walk.nbytes)) { padlock_xcrypt_cbc(walk.src.virt.addr, walk.dst.virt.addr, ctx->D, walk.iv, &ctx->cword.decrypt, @@ -354,6 +379,7 @@ static int cbc_aes_decrypt(struct blkcipher_desc *desc, err = blkcipher_walk_done(desc, &walk, nbytes); } + irq_ts_restore(ts_state); return err; } diff --git a/drivers/crypto/padlock-sha.c b/drivers/crypto/padlock-sha.c index 40d5680fa01..a7fbadebf62 100644 --- a/drivers/crypto/padlock-sha.c +++ b/drivers/crypto/padlock-sha.c @@ -22,6 +22,7 @@ #include #include #include +#include #include "padlock.h" #define SHA1_DEFAULT_FALLBACK "sha1-generic" @@ -102,6 +103,7 @@ static void padlock_do_sha1(const char *in, char *out, int count) * PadLock microcode needs it that big. */ char buf[128+16]; char *result = NEAREST_ALIGNED(buf); + int ts_state; ((uint32_t *)result)[0] = SHA1_H0; ((uint32_t *)result)[1] = SHA1_H1; @@ -109,9 +111,12 @@ static void padlock_do_sha1(const char *in, char *out, int count) ((uint32_t *)result)[3] = SHA1_H3; ((uint32_t *)result)[4] = SHA1_H4; + /* prevent taking the spurious DNA fault with padlock. */ + ts_state = irq_ts_save(); asm volatile (".byte 0xf3,0x0f,0xa6,0xc8" /* rep xsha1 */ : "+S"(in), "+D"(result) : "c"(count), "a"(0)); + irq_ts_restore(ts_state); padlock_output_block((uint32_t *)result, (uint32_t *)out, 5); } @@ -123,6 +128,7 @@ static void padlock_do_sha256(const char *in, char *out, int count) * PadLock microcode needs it that big. */ char buf[128+16]; char *result = NEAREST_ALIGNED(buf); + int ts_state; ((uint32_t *)result)[0] = SHA256_H0; ((uint32_t *)result)[1] = SHA256_H1; @@ -133,9 +139,12 @@ static void padlock_do_sha256(const char *in, char *out, int count) ((uint32_t *)result)[6] = SHA256_H6; ((uint32_t *)result)[7] = SHA256_H7; + /* prevent taking the spurious DNA fault with padlock. */ + ts_state = irq_ts_save(); asm volatile (".byte 0xf3,0x0f,0xa6,0xd0" /* rep xsha256 */ : "+S"(in), "+D"(result) : "c"(count), "a"(0)); + irq_ts_restore(ts_state); padlock_output_block((uint32_t *)result, (uint32_t *)out, 8); } diff --git a/include/asm-x86/i387.h b/include/asm-x86/i387.h index 96fa8449ff1..6d3b2106341 100644 --- a/include/asm-x86/i387.h +++ b/include/asm-x86/i387.h @@ -13,6 +13,7 @@ #include #include #include +#include #include #include #include @@ -236,6 +237,37 @@ static inline void kernel_fpu_end(void) preempt_enable(); } +/* + * Some instructions like VIA's padlock instructions generate a spurious + * DNA fault but don't modify SSE registers. And these instructions + * get used from interrupt context aswell. To prevent these kernel instructions + * in interrupt context interact wrongly with other user/kernel fpu usage, we + * should use them only in the context of irq_ts_save/restore() + */ +static inline int irq_ts_save(void) +{ + /* + * If we are in process context, we are ok to take a spurious DNA fault. + * Otherwise, doing clts() in process context require pre-emption to + * be disabled or some heavy lifting like kernel_fpu_begin() + */ + if (!in_interrupt()) + return 0; + + if (read_cr0() & X86_CR0_TS) { + clts(); + return 1; + } + + return 0; +} + +static inline void irq_ts_restore(int TS_state) +{ + if (TS_state) + stts(); +} + #ifdef CONFIG_X86_64 static inline void save_init_fpu(struct task_struct *tsk) -- GitLab From 6b3560229d3b6be7443fa9f9c6502e660bcfef5f Mon Sep 17 00:00:00 2001 From: Marcin Slusarz Date: Tue, 12 Aug 2008 23:23:05 +0200 Subject: [PATCH 228/750] x86: fix 2 section mismatch warnings - find_and_reserve_crashkernel WARNING: vmlinux.o(.text+0xcd1f): Section mismatch in reference from the function find_and_reserve_crashkernel() to the function .init.text:find_e820_area() The function find_and_reserve_crashkernel() references the function __init find_e820_area(). This is often because find_and_reserve_crashkernel lacks a __init annotation or the annotation of find_e820_area is wrong. WARNING: vmlinux.o(.text+0xcd38): Section mismatch in reference from the function find_and_reserve_crashkernel() to the function .init.text:reserve_bootmem_generic() The function find_and_reserve_crashkernel() references the function __init reserve_bootmem_generic(). This is often because find_and_reserve_crashkernel lacks a __init annotation or the annotation of reserve_bootmem_generic is wrong. find_and_reserve_crashkernel is called from __init function (reserve_crashkernel) and calls 2 __init functions (find_e820_area, reserve_bootmem_generic), so mark it __init Signed-off-by: Marcin Slusarz Signed-off-by: Ingo Molnar --- arch/x86/kernel/setup.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/setup.c b/arch/x86/kernel/setup.c index 68b48e3fbcb..a4656adab53 100644 --- a/arch/x86/kernel/setup.c +++ b/arch/x86/kernel/setup.c @@ -445,7 +445,7 @@ static void __init reserve_early_setup_data(void) * @size: Size of the crashkernel memory to reserve. * Returns the base address on success, and -1ULL on failure. */ -unsigned long long find_and_reserve_crashkernel(unsigned long long size) +unsigned long long __init find_and_reserve_crashkernel(unsigned long long size) { const unsigned long long alignment = 16<<20; /* 16M */ unsigned long long start = 0LL; -- GitLab From a726c6009e6eba4acfccf8b683854866eeabb184 Mon Sep 17 00:00:00 2001 From: John Keller Date: Tue, 29 Jul 2008 14:34:16 -0500 Subject: [PATCH 229/750] x86: allow MMCONFIG above 4GB on x86_64 SGI UV will have MMCFG base addresses that are greater than 4GB (32 bits). v2: Use CONFIG_RESOURCES_64BIT instead of CONFIG_X86_64. v3: Create a flag, that is set by platform specific code, to disable the > 4GB check. Signed-off-by: John Keller Cc: jpk@sgi.com Signed-off-by: Ingo Molnar --- arch/x86/kernel/acpi/boot.c | 16 +++++++++++++++- 1 file changed, 15 insertions(+), 1 deletion(-) diff --git a/arch/x86/kernel/acpi/boot.c b/arch/x86/kernel/acpi/boot.c index fa88a1d7129..bfd10fd211c 100644 --- a/arch/x86/kernel/acpi/boot.c +++ b/arch/x86/kernel/acpi/boot.c @@ -97,6 +97,8 @@ static u64 acpi_lapic_addr __initdata = APIC_DEFAULT_PHYS_BASE; #warning ACPI uses CMPXCHG, i486 and later hardware #endif +static int acpi_mcfg_64bit_base_addr __initdata = FALSE; + /* -------------------------------------------------------------------------- Boot-time Configuration -------------------------------------------------------------------------- */ @@ -158,6 +160,14 @@ char *__init __acpi_map_table(unsigned long phys, unsigned long size) struct acpi_mcfg_allocation *pci_mmcfg_config; int pci_mmcfg_config_num; +static int __init acpi_mcfg_oem_check(struct acpi_table_mcfg *mcfg) +{ + if (!strcmp(mcfg->header.oem_id, "SGI")) + acpi_mcfg_64bit_base_addr = TRUE; + + return 0; +} + int __init acpi_parse_mcfg(struct acpi_table_header *header) { struct acpi_table_mcfg *mcfg; @@ -190,8 +200,12 @@ int __init acpi_parse_mcfg(struct acpi_table_header *header) } memcpy(pci_mmcfg_config, &mcfg[1], config_size); + + acpi_mcfg_oem_check(mcfg); + for (i = 0; i < pci_mmcfg_config_num; ++i) { - if (pci_mmcfg_config[i].address > 0xFFFFFFFF) { + if ((pci_mmcfg_config[i].address > 0xFFFFFFFF) && + !acpi_mcfg_64bit_base_addr) { printk(KERN_ERR PREFIX "MMCONFIG not in low 4GB of memory\n"); kfree(pci_mmcfg_config); -- GitLab From 0a883a05c54b326bcf99c0902af28dae0386be0a Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Wed, 13 Aug 2008 14:13:26 +0300 Subject: [PATCH 230/750] UBIFS: few commentary fixes Signed-off-by: Artem Bityutskiy --- fs/ubifs/super.c | 8 ++++---- fs/ubifs/ubifs.h | 2 -- 2 files changed, 4 insertions(+), 6 deletions(-) diff --git a/fs/ubifs/super.c b/fs/ubifs/super.c index 2c268a47641..f71e6b8822c 100644 --- a/fs/ubifs/super.c +++ b/fs/ubifs/super.c @@ -148,7 +148,7 @@ struct inode *ubifs_iget(struct super_block *sb, unsigned long inum) if (err) goto out_invalid; - /* Disable readahead */ + /* Disable read-ahead */ inode->i_mapping->backing_dev_info = &c->bdi; switch (inode->i_mode & S_IFMT) { @@ -344,7 +344,7 @@ static void ubifs_delete_inode(struct inode *inode) if (err) /* * Worst case we have a lost orphan inode wasting space, so a - * simple error message is ok here. + * simple error message is OK here. */ ubifs_err("can't delete inode %lu, error %d", inode->i_ino, err); @@ -1683,10 +1683,10 @@ static int ubifs_fill_super(struct super_block *sb, void *data, int silent) } /* - * UBIFS provids 'backing_dev_info' in order to disable readahead. For + * UBIFS provides 'backing_dev_info' in order to disable read-ahead. For * UBIFS, I/O is not deferred, it is done immediately in readpage, * which means the user would have to wait not just for their own I/O - * but the readahead I/O as well i.e. completely pointless. + * but the read-ahead I/O as well i.e. completely pointless. * * Read-ahead will be disabled because @c->bdi.ra_pages is 0. */ diff --git a/fs/ubifs/ubifs.h b/fs/ubifs/ubifs.h index f2dd749d798..d7f706f7a30 100644 --- a/fs/ubifs/ubifs.h +++ b/fs/ubifs/ubifs.h @@ -20,8 +20,6 @@ * Adrian Hunter */ -/* Implementation version 0.7 */ - #ifndef __UBIFS_H__ #define __UBIFS_H__ -- GitLab From 720b499c806200d06f4f22c668d46db784117089 Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Wed, 13 Aug 2008 16:16:31 +0300 Subject: [PATCH 231/750] UBIFS: remove unneeded check Commit d70b67c8bc72ee23b55381bd6a884f4796692f77 fixed VFS and it never calls FS lookup function in deleted directories now. We may remove corresponding UBIFS check. Signed-off-by: Artem Bityutskiy --- fs/ubifs/dir.c | 10 +--------- 1 file changed, 1 insertion(+), 9 deletions(-) diff --git a/fs/ubifs/dir.c b/fs/ubifs/dir.c index 0d1ab8967a4..5c96f1fb701 100644 --- a/fs/ubifs/dir.c +++ b/fs/ubifs/dir.c @@ -219,15 +219,7 @@ static struct dentry *ubifs_lookup(struct inode *dir, struct dentry *dentry, err = ubifs_tnc_lookup_nm(c, &key, dent, &dentry->d_name); if (err) { - /* - * Do not hash the direntry if parent 'i_nlink' is zero, because - * this has side-effects - '->delete_inode()' call will not be - * called for the parent orphan inode, because 'd_count' of its - * direntry will stay 1 (it'll be negative direntry I guess) - * and prevent 'iput_final()' until the dentry is destroyed due - * to unmount or memory pressure. - */ - if (err == -ENOENT && dir->i_nlink != 0) { + if (err == -ENOENT) { dbg_gen("not found"); goto done; } -- GitLab From 875e40b97571e1f06d1184ad6cbb2acf9cb31a23 Mon Sep 17 00:00:00 2001 From: Arjan van de Ven Date: Wed, 30 Jul 2008 12:26:26 -0700 Subject: [PATCH 232/750] x86: use WARN() in arch/x86/mm/pageattr.c Use WARN() instead of a printk+WARN_ON() pair; this way the message becomes part of the warning section for better reporting/collection. Signed-off-by: Arjan van de Ven Acked-by: Ingo Molnar Signed-off-by: Andrew Morton Cc: akpm@linux-foundation.org Cc: arjan@linux.intel.com Signed-off-by: Ingo Molnar --- arch/x86/mm/pageattr-test.c | 3 +-- arch/x86/mm/pageattr.c | 3 +-- 2 files changed, 2 insertions(+), 4 deletions(-) diff --git a/arch/x86/mm/pageattr-test.c b/arch/x86/mm/pageattr-test.c index 0dcd42eb94e..d4aa503caaa 100644 --- a/arch/x86/mm/pageattr-test.c +++ b/arch/x86/mm/pageattr-test.c @@ -221,8 +221,7 @@ static int pageattr_test(void) failed += print_split(&sc); if (failed) { - printk(KERN_ERR "NOT PASSED. Please report.\n"); - WARN_ON(1); + WARN(1, KERN_ERR "NOT PASSED. Please report.\n"); return -EINVAL; } else { if (print) diff --git a/arch/x86/mm/pageattr.c b/arch/x86/mm/pageattr.c index 65c6e46bf05..ba24537d69d 100644 --- a/arch/x86/mm/pageattr.c +++ b/arch/x86/mm/pageattr.c @@ -592,10 +592,9 @@ repeat: if (!pte_val(old_pte)) { if (!primary) return 0; - printk(KERN_WARNING "CPA: called for zero pte. " + WARN(1, KERN_WARNING "CPA: called for zero pte. " "vaddr = %lx cpa->vaddr = %lx\n", address, cpa->vaddr); - WARN_ON(1); return -EINVAL; } -- GitLab From 2df8b1d656021e180ab93c8a4b2c9c2923d30b82 Mon Sep 17 00:00:00 2001 From: Arjan van de Ven Date: Wed, 30 Jul 2008 12:43:11 -0700 Subject: [PATCH 233/750] lockdep: use WARN() in kernel/lockdep.c Use WARN() instead of a printk+WARN_ON() pair; this way the message becomes part of the warning section for better reporting/collection. Signed-off-by: Arjan van de Ven Signed-off-by: Ingo Molnar Signed-off-by: Andrew Morton --- kernel/lockdep.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) diff --git a/kernel/lockdep.c b/kernel/lockdep.c index 1aa91fd6b06..77fa776a2da 100644 --- a/kernel/lockdep.c +++ b/kernel/lockdep.c @@ -1759,11 +1759,10 @@ static void check_chain_key(struct task_struct *curr) hlock = curr->held_locks + i; if (chain_key != hlock->prev_chain_key) { debug_locks_off(); - printk("hm#1, depth: %u [%u], %016Lx != %016Lx\n", + WARN(1, "hm#1, depth: %u [%u], %016Lx != %016Lx\n", curr->lockdep_depth, i, (unsigned long long)chain_key, (unsigned long long)hlock->prev_chain_key); - WARN_ON(1); return; } id = hlock->class_idx - 1; @@ -1778,11 +1777,10 @@ static void check_chain_key(struct task_struct *curr) } if (chain_key != curr->curr_chain_key) { debug_locks_off(); - printk("hm#2, depth: %u [%u], %016Lx != %016Lx\n", + WARN(1, "hm#2, depth: %u [%u], %016Lx != %016Lx\n", curr->lockdep_depth, i, (unsigned long long)chain_key, (unsigned long long)curr->curr_chain_key); - WARN_ON(1); } #endif } -- GitLab From cb980d9a3ec3d39e30e0a4c473df528c09e0dcf3 Mon Sep 17 00:00:00 2001 From: David Teigland Date: Tue, 29 Jul 2008 15:21:19 -0500 Subject: [PATCH 234/750] dlm: add missing kfrees A couple of unlikely error conditions were missing a kfree on the error exit path. Reported-by: Juha Leppanen Signed-off-by: David Teigland --- fs/dlm/user.c | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-) diff --git a/fs/dlm/user.c b/fs/dlm/user.c index 929e48ae759..34f14a14fb4 100644 --- a/fs/dlm/user.c +++ b/fs/dlm/user.c @@ -527,8 +527,10 @@ static ssize_t device_write(struct file *file, const char __user *buf, k32buf = (struct dlm_write_request32 *)kbuf; kbuf = kmalloc(count + 1 + (sizeof(struct dlm_write_request) - sizeof(struct dlm_write_request32)), GFP_KERNEL); - if (!kbuf) + if (!kbuf) { + kfree(k32buf); return -ENOMEM; + } if (proc) set_bit(DLM_PROC_FLAGS_COMPAT, &proc->flags); @@ -539,8 +541,10 @@ static ssize_t device_write(struct file *file, const char __user *buf, /* do we really need this? can a write happen after a close? */ if ((kbuf->cmd == DLM_USER_LOCK || kbuf->cmd == DLM_USER_UNLOCK) && - (proc && test_bit(DLM_PROC_FLAGS_CLOSING, &proc->flags))) - return -EINVAL; + (proc && test_bit(DLM_PROC_FLAGS_CLOSING, &proc->flags))) { + error = -EINVAL; + goto out_free; + } sigfillset(&allsigs); sigprocmask(SIG_BLOCK, &allsigs, &tmpsig); -- GitLab From 51409340d240dabe66adb49f645588c3a802d055 Mon Sep 17 00:00:00 2001 From: David Teigland Date: Thu, 31 Jul 2008 09:31:53 -0500 Subject: [PATCH 235/750] dlm: rename structs Add a dlm_ prefix to the struct names in config.c. This resolves a conflict with struct node in particular, when include/linux/node.h happens to be included. Reported-by: Andrew Morton Signed-off-by: David Teigland --- fs/dlm/config.c | 203 +++++++++++++++++++++++++----------------------- 1 file changed, 107 insertions(+), 96 deletions(-) diff --git a/fs/dlm/config.c b/fs/dlm/config.c index c4e7d721bd8..89d2fb7b991 100644 --- a/fs/dlm/config.c +++ b/fs/dlm/config.c @@ -2,7 +2,7 @@ ******************************************************************************* ** ** Copyright (C) Sistina Software, Inc. 1997-2003 All rights reserved. -** Copyright (C) 2004-2007 Red Hat, Inc. All rights reserved. +** Copyright (C) 2004-2008 Red Hat, Inc. All rights reserved. ** ** This copyrighted material is made available to anyone wishing to use, ** modify, copy, or redistribute it subject to the terms and conditions @@ -30,16 +30,16 @@ static struct config_group *space_list; static struct config_group *comm_list; -static struct comm *local_comm; +static struct dlm_comm *local_comm; -struct clusters; -struct cluster; -struct spaces; -struct space; -struct comms; -struct comm; -struct nodes; -struct node; +struct dlm_clusters; +struct dlm_cluster; +struct dlm_spaces; +struct dlm_space; +struct dlm_comms; +struct dlm_comm; +struct dlm_nodes; +struct dlm_node; static struct config_group *make_cluster(struct config_group *, const char *); static void drop_cluster(struct config_group *, struct config_item *); @@ -68,17 +68,22 @@ static ssize_t show_node(struct config_item *i, struct configfs_attribute *a, static ssize_t store_node(struct config_item *i, struct configfs_attribute *a, const char *buf, size_t len); -static ssize_t comm_nodeid_read(struct comm *cm, char *buf); -static ssize_t comm_nodeid_write(struct comm *cm, const char *buf, size_t len); -static ssize_t comm_local_read(struct comm *cm, char *buf); -static ssize_t comm_local_write(struct comm *cm, const char *buf, size_t len); -static ssize_t comm_addr_write(struct comm *cm, const char *buf, size_t len); -static ssize_t node_nodeid_read(struct node *nd, char *buf); -static ssize_t node_nodeid_write(struct node *nd, const char *buf, size_t len); -static ssize_t node_weight_read(struct node *nd, char *buf); -static ssize_t node_weight_write(struct node *nd, const char *buf, size_t len); - -struct cluster { +static ssize_t comm_nodeid_read(struct dlm_comm *cm, char *buf); +static ssize_t comm_nodeid_write(struct dlm_comm *cm, const char *buf, + size_t len); +static ssize_t comm_local_read(struct dlm_comm *cm, char *buf); +static ssize_t comm_local_write(struct dlm_comm *cm, const char *buf, + size_t len); +static ssize_t comm_addr_write(struct dlm_comm *cm, const char *buf, + size_t len); +static ssize_t node_nodeid_read(struct dlm_node *nd, char *buf); +static ssize_t node_nodeid_write(struct dlm_node *nd, const char *buf, + size_t len); +static ssize_t node_weight_read(struct dlm_node *nd, char *buf); +static ssize_t node_weight_write(struct dlm_node *nd, const char *buf, + size_t len); + +struct dlm_cluster { struct config_group group; unsigned int cl_tcp_port; unsigned int cl_buffer_size; @@ -109,11 +114,11 @@ enum { struct cluster_attribute { struct configfs_attribute attr; - ssize_t (*show)(struct cluster *, char *); - ssize_t (*store)(struct cluster *, const char *, size_t); + ssize_t (*show)(struct dlm_cluster *, char *); + ssize_t (*store)(struct dlm_cluster *, const char *, size_t); }; -static ssize_t cluster_set(struct cluster *cl, unsigned int *cl_field, +static ssize_t cluster_set(struct dlm_cluster *cl, unsigned int *cl_field, int *info_field, int check_zero, const char *buf, size_t len) { @@ -134,12 +139,12 @@ static ssize_t cluster_set(struct cluster *cl, unsigned int *cl_field, } #define CLUSTER_ATTR(name, check_zero) \ -static ssize_t name##_write(struct cluster *cl, const char *buf, size_t len) \ +static ssize_t name##_write(struct dlm_cluster *cl, const char *buf, size_t len) \ { \ return cluster_set(cl, &cl->cl_##name, &dlm_config.ci_##name, \ check_zero, buf, len); \ } \ -static ssize_t name##_read(struct cluster *cl, char *buf) \ +static ssize_t name##_read(struct dlm_cluster *cl, char *buf) \ { \ return snprintf(buf, PAGE_SIZE, "%u\n", cl->cl_##name); \ } \ @@ -181,8 +186,8 @@ enum { struct comm_attribute { struct configfs_attribute attr; - ssize_t (*show)(struct comm *, char *); - ssize_t (*store)(struct comm *, const char *, size_t); + ssize_t (*show)(struct dlm_comm *, char *); + ssize_t (*store)(struct dlm_comm *, const char *, size_t); }; static struct comm_attribute comm_attr_nodeid = { @@ -222,8 +227,8 @@ enum { struct node_attribute { struct configfs_attribute attr; - ssize_t (*show)(struct node *, char *); - ssize_t (*store)(struct node *, const char *, size_t); + ssize_t (*show)(struct dlm_node *, char *); + ssize_t (*store)(struct dlm_node *, const char *, size_t); }; static struct node_attribute node_attr_nodeid = { @@ -248,26 +253,26 @@ static struct configfs_attribute *node_attrs[] = { NULL, }; -struct clusters { +struct dlm_clusters { struct configfs_subsystem subsys; }; -struct spaces { +struct dlm_spaces { struct config_group ss_group; }; -struct space { +struct dlm_space { struct config_group group; struct list_head members; struct mutex members_lock; int members_count; }; -struct comms { +struct dlm_comms { struct config_group cs_group; }; -struct comm { +struct dlm_comm { struct config_item item; int nodeid; int local; @@ -275,11 +280,11 @@ struct comm { struct sockaddr_storage *addr[DLM_MAX_ADDR_COUNT]; }; -struct nodes { +struct dlm_nodes { struct config_group ns_group; }; -struct node { +struct dlm_node { struct config_item item; struct list_head list; /* space->members */ int nodeid; @@ -372,38 +377,40 @@ static struct config_item_type node_type = { .ct_owner = THIS_MODULE, }; -static struct cluster *to_cluster(struct config_item *i) +static struct dlm_cluster *to_cluster(struct config_item *i) { - return i ? container_of(to_config_group(i), struct cluster, group):NULL; + return i ? container_of(to_config_group(i), struct dlm_cluster, group) : + NULL; } -static struct space *to_space(struct config_item *i) +static struct dlm_space *to_space(struct config_item *i) { - return i ? container_of(to_config_group(i), struct space, group) : NULL; + return i ? container_of(to_config_group(i), struct dlm_space, group) : + NULL; } -static struct comm *to_comm(struct config_item *i) +static struct dlm_comm *to_comm(struct config_item *i) { - return i ? container_of(i, struct comm, item) : NULL; + return i ? container_of(i, struct dlm_comm, item) : NULL; } -static struct node *to_node(struct config_item *i) +static struct dlm_node *to_node(struct config_item *i) { - return i ? container_of(i, struct node, item) : NULL; + return i ? container_of(i, struct dlm_node, item) : NULL; } static struct config_group *make_cluster(struct config_group *g, const char *name) { - struct cluster *cl = NULL; - struct spaces *sps = NULL; - struct comms *cms = NULL; + struct dlm_cluster *cl = NULL; + struct dlm_spaces *sps = NULL; + struct dlm_comms *cms = NULL; void *gps = NULL; - cl = kzalloc(sizeof(struct cluster), GFP_KERNEL); + cl = kzalloc(sizeof(struct dlm_cluster), GFP_KERNEL); gps = kcalloc(3, sizeof(struct config_group *), GFP_KERNEL); - sps = kzalloc(sizeof(struct spaces), GFP_KERNEL); - cms = kzalloc(sizeof(struct comms), GFP_KERNEL); + sps = kzalloc(sizeof(struct dlm_spaces), GFP_KERNEL); + cms = kzalloc(sizeof(struct dlm_comms), GFP_KERNEL); if (!cl || !gps || !sps || !cms) goto fail; @@ -443,7 +450,7 @@ static struct config_group *make_cluster(struct config_group *g, static void drop_cluster(struct config_group *g, struct config_item *i) { - struct cluster *cl = to_cluster(i); + struct dlm_cluster *cl = to_cluster(i); struct config_item *tmp; int j; @@ -461,20 +468,20 @@ static void drop_cluster(struct config_group *g, struct config_item *i) static void release_cluster(struct config_item *i) { - struct cluster *cl = to_cluster(i); + struct dlm_cluster *cl = to_cluster(i); kfree(cl->group.default_groups); kfree(cl); } static struct config_group *make_space(struct config_group *g, const char *name) { - struct space *sp = NULL; - struct nodes *nds = NULL; + struct dlm_space *sp = NULL; + struct dlm_nodes *nds = NULL; void *gps = NULL; - sp = kzalloc(sizeof(struct space), GFP_KERNEL); + sp = kzalloc(sizeof(struct dlm_space), GFP_KERNEL); gps = kcalloc(2, sizeof(struct config_group *), GFP_KERNEL); - nds = kzalloc(sizeof(struct nodes), GFP_KERNEL); + nds = kzalloc(sizeof(struct dlm_nodes), GFP_KERNEL); if (!sp || !gps || !nds) goto fail; @@ -500,7 +507,7 @@ static struct config_group *make_space(struct config_group *g, const char *name) static void drop_space(struct config_group *g, struct config_item *i) { - struct space *sp = to_space(i); + struct dlm_space *sp = to_space(i); struct config_item *tmp; int j; @@ -517,16 +524,16 @@ static void drop_space(struct config_group *g, struct config_item *i) static void release_space(struct config_item *i) { - struct space *sp = to_space(i); + struct dlm_space *sp = to_space(i); kfree(sp->group.default_groups); kfree(sp); } static struct config_item *make_comm(struct config_group *g, const char *name) { - struct comm *cm; + struct dlm_comm *cm; - cm = kzalloc(sizeof(struct comm), GFP_KERNEL); + cm = kzalloc(sizeof(struct dlm_comm), GFP_KERNEL); if (!cm) return ERR_PTR(-ENOMEM); @@ -539,7 +546,7 @@ static struct config_item *make_comm(struct config_group *g, const char *name) static void drop_comm(struct config_group *g, struct config_item *i) { - struct comm *cm = to_comm(i); + struct dlm_comm *cm = to_comm(i); if (local_comm == cm) local_comm = NULL; dlm_lowcomms_close(cm->nodeid); @@ -550,16 +557,16 @@ static void drop_comm(struct config_group *g, struct config_item *i) static void release_comm(struct config_item *i) { - struct comm *cm = to_comm(i); + struct dlm_comm *cm = to_comm(i); kfree(cm); } static struct config_item *make_node(struct config_group *g, const char *name) { - struct space *sp = to_space(g->cg_item.ci_parent); - struct node *nd; + struct dlm_space *sp = to_space(g->cg_item.ci_parent); + struct dlm_node *nd; - nd = kzalloc(sizeof(struct node), GFP_KERNEL); + nd = kzalloc(sizeof(struct dlm_node), GFP_KERNEL); if (!nd) return ERR_PTR(-ENOMEM); @@ -578,8 +585,8 @@ static struct config_item *make_node(struct config_group *g, const char *name) static void drop_node(struct config_group *g, struct config_item *i) { - struct space *sp = to_space(g->cg_item.ci_parent); - struct node *nd = to_node(i); + struct dlm_space *sp = to_space(g->cg_item.ci_parent); + struct dlm_node *nd = to_node(i); mutex_lock(&sp->members_lock); list_del(&nd->list); @@ -591,11 +598,11 @@ static void drop_node(struct config_group *g, struct config_item *i) static void release_node(struct config_item *i) { - struct node *nd = to_node(i); + struct dlm_node *nd = to_node(i); kfree(nd); } -static struct clusters clusters_root = { +static struct dlm_clusters clusters_root = { .subsys = { .su_group = { .cg_item = { @@ -625,7 +632,7 @@ void dlm_config_exit(void) static ssize_t show_cluster(struct config_item *i, struct configfs_attribute *a, char *buf) { - struct cluster *cl = to_cluster(i); + struct dlm_cluster *cl = to_cluster(i); struct cluster_attribute *cla = container_of(a, struct cluster_attribute, attr); return cla->show ? cla->show(cl, buf) : 0; @@ -635,7 +642,7 @@ static ssize_t store_cluster(struct config_item *i, struct configfs_attribute *a, const char *buf, size_t len) { - struct cluster *cl = to_cluster(i); + struct dlm_cluster *cl = to_cluster(i); struct cluster_attribute *cla = container_of(a, struct cluster_attribute, attr); return cla->store ? cla->store(cl, buf, len) : -EINVAL; @@ -644,7 +651,7 @@ static ssize_t store_cluster(struct config_item *i, static ssize_t show_comm(struct config_item *i, struct configfs_attribute *a, char *buf) { - struct comm *cm = to_comm(i); + struct dlm_comm *cm = to_comm(i); struct comm_attribute *cma = container_of(a, struct comm_attribute, attr); return cma->show ? cma->show(cm, buf) : 0; @@ -653,29 +660,31 @@ static ssize_t show_comm(struct config_item *i, struct configfs_attribute *a, static ssize_t store_comm(struct config_item *i, struct configfs_attribute *a, const char *buf, size_t len) { - struct comm *cm = to_comm(i); + struct dlm_comm *cm = to_comm(i); struct comm_attribute *cma = container_of(a, struct comm_attribute, attr); return cma->store ? cma->store(cm, buf, len) : -EINVAL; } -static ssize_t comm_nodeid_read(struct comm *cm, char *buf) +static ssize_t comm_nodeid_read(struct dlm_comm *cm, char *buf) { return sprintf(buf, "%d\n", cm->nodeid); } -static ssize_t comm_nodeid_write(struct comm *cm, const char *buf, size_t len) +static ssize_t comm_nodeid_write(struct dlm_comm *cm, const char *buf, + size_t len) { cm->nodeid = simple_strtol(buf, NULL, 0); return len; } -static ssize_t comm_local_read(struct comm *cm, char *buf) +static ssize_t comm_local_read(struct dlm_comm *cm, char *buf) { return sprintf(buf, "%d\n", cm->local); } -static ssize_t comm_local_write(struct comm *cm, const char *buf, size_t len) +static ssize_t comm_local_write(struct dlm_comm *cm, const char *buf, + size_t len) { cm->local= simple_strtol(buf, NULL, 0); if (cm->local && !local_comm) @@ -683,7 +692,7 @@ static ssize_t comm_local_write(struct comm *cm, const char *buf, size_t len) return len; } -static ssize_t comm_addr_write(struct comm *cm, const char *buf, size_t len) +static ssize_t comm_addr_write(struct dlm_comm *cm, const char *buf, size_t len) { struct sockaddr_storage *addr; @@ -705,7 +714,7 @@ static ssize_t comm_addr_write(struct comm *cm, const char *buf, size_t len) static ssize_t show_node(struct config_item *i, struct configfs_attribute *a, char *buf) { - struct node *nd = to_node(i); + struct dlm_node *nd = to_node(i); struct node_attribute *nda = container_of(a, struct node_attribute, attr); return nda->show ? nda->show(nd, buf) : 0; @@ -714,29 +723,31 @@ static ssize_t show_node(struct config_item *i, struct configfs_attribute *a, static ssize_t store_node(struct config_item *i, struct configfs_attribute *a, const char *buf, size_t len) { - struct node *nd = to_node(i); + struct dlm_node *nd = to_node(i); struct node_attribute *nda = container_of(a, struct node_attribute, attr); return nda->store ? nda->store(nd, buf, len) : -EINVAL; } -static ssize_t node_nodeid_read(struct node *nd, char *buf) +static ssize_t node_nodeid_read(struct dlm_node *nd, char *buf) { return sprintf(buf, "%d\n", nd->nodeid); } -static ssize_t node_nodeid_write(struct node *nd, const char *buf, size_t len) +static ssize_t node_nodeid_write(struct dlm_node *nd, const char *buf, + size_t len) { nd->nodeid = simple_strtol(buf, NULL, 0); return len; } -static ssize_t node_weight_read(struct node *nd, char *buf) +static ssize_t node_weight_read(struct dlm_node *nd, char *buf) { return sprintf(buf, "%d\n", nd->weight); } -static ssize_t node_weight_write(struct node *nd, const char *buf, size_t len) +static ssize_t node_weight_write(struct dlm_node *nd, const char *buf, + size_t len) { nd->weight = simple_strtol(buf, NULL, 0); return len; @@ -746,7 +757,7 @@ static ssize_t node_weight_write(struct node *nd, const char *buf, size_t len) * Functions for the dlm to get the info that's been configured */ -static struct space *get_space(char *name) +static struct dlm_space *get_space(char *name) { struct config_item *i; @@ -760,15 +771,15 @@ static struct space *get_space(char *name) return to_space(i); } -static void put_space(struct space *sp) +static void put_space(struct dlm_space *sp) { config_item_put(&sp->group.cg_item); } -static struct comm *get_comm(int nodeid, struct sockaddr_storage *addr) +static struct dlm_comm *get_comm(int nodeid, struct sockaddr_storage *addr) { struct config_item *i; - struct comm *cm = NULL; + struct dlm_comm *cm = NULL; int found = 0; if (!comm_list) @@ -801,7 +812,7 @@ static struct comm *get_comm(int nodeid, struct sockaddr_storage *addr) return cm; } -static void put_comm(struct comm *cm) +static void put_comm(struct dlm_comm *cm) { config_item_put(&cm->item); } @@ -810,8 +821,8 @@ static void put_comm(struct comm *cm) int dlm_nodeid_list(char *lsname, int **ids_out, int *ids_count_out, int **new_out, int *new_count_out) { - struct space *sp; - struct node *nd; + struct dlm_space *sp; + struct dlm_node *nd; int i = 0, rv = 0, ids_count = 0, new_count = 0; int *ids, *new; @@ -874,8 +885,8 @@ int dlm_nodeid_list(char *lsname, int **ids_out, int *ids_count_out, int dlm_node_weight(char *lsname, int nodeid) { - struct space *sp; - struct node *nd; + struct dlm_space *sp; + struct dlm_node *nd; int w = -EEXIST; sp = get_space(lsname); @@ -897,7 +908,7 @@ int dlm_node_weight(char *lsname, int nodeid) int dlm_nodeid_to_addr(int nodeid, struct sockaddr_storage *addr) { - struct comm *cm = get_comm(nodeid, NULL); + struct dlm_comm *cm = get_comm(nodeid, NULL); if (!cm) return -EEXIST; if (!cm->addr_count) @@ -909,7 +920,7 @@ int dlm_nodeid_to_addr(int nodeid, struct sockaddr_storage *addr) int dlm_addr_to_nodeid(struct sockaddr_storage *addr, int *nodeid) { - struct comm *cm = get_comm(0, addr); + struct dlm_comm *cm = get_comm(0, addr); if (!cm) return -EEXIST; *nodeid = cm->nodeid; -- GitLab From c1e24df27fb1058739789126db6ad1b1ef719346 Mon Sep 17 00:00:00 2001 From: Jean-Christophe DUBOIS Date: Wed, 13 Aug 2008 13:35:37 -0700 Subject: [PATCH 236/750] xfrm: remove unnecessary variable in xfrm_output_resume() 2nd try Small fix removing an unnecessary intermediate variable. Signed-off-by: Jean-Christophe DUBOIS Signed-off-by: David S. Miller --- net/xfrm/xfrm_output.c | 5 +---- 1 file changed, 1 insertion(+), 4 deletions(-) diff --git a/net/xfrm/xfrm_output.c b/net/xfrm/xfrm_output.c index 3f964db908a..ac25b4c0e98 100644 --- a/net/xfrm/xfrm_output.c +++ b/net/xfrm/xfrm_output.c @@ -112,16 +112,13 @@ error_nolock: int xfrm_output_resume(struct sk_buff *skb, int err) { while (likely((err = xfrm_output_one(skb, err)) == 0)) { - struct xfrm_state *x; - nf_reset(skb); err = skb->dst->ops->local_out(skb); if (unlikely(err != 1)) goto out; - x = skb->dst->xfrm; - if (!x) + if (!skb->dst->xfrm) return dst_output(skb); err = nf_hook(skb->dst->ops->family, -- GitLab From 3e8a0a559c66ee9e7468195691a56fefc3589740 Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Wed, 13 Aug 2008 13:48:39 -0700 Subject: [PATCH 237/750] dccp: change L/R must have at least one byte in the dccpsf_val field Thanks to Eugene Teo for reporting this problem. Signed-off-by: Eugene Teo Signed-off-by: Arnaldo Carvalho de Melo Signed-off-by: Gerrit Renker Signed-off-by: David S. Miller --- net/dccp/proto.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/net/dccp/proto.c b/net/dccp/proto.c index b622d974485..1ca3b26eed0 100644 --- a/net/dccp/proto.c +++ b/net/dccp/proto.c @@ -474,6 +474,11 @@ static int dccp_setsockopt_change(struct sock *sk, int type, if (copy_from_user(&opt, optval, sizeof(opt))) return -EFAULT; + /* + * rfc4340: 6.1. Change Options + */ + if (opt.dccpsf_len < 1) + return -EINVAL; val = kmalloc(opt.dccpsf_len, GFP_KERNEL); if (!val) -- GitLab From 758db3f2118703a1e36374dae5d58bed963e7e0d Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Wed, 13 Aug 2008 14:26:22 -0700 Subject: [PATCH 238/750] [h8300] move include/asm-h8300 to arch/h8300/include/asm Done as a script (well, a single "git mv" actually) on request from Yoshinori Sato as a way to avoid a huge diff. Requested-by: Yoshinori Sato Cc: Sam Ravnborg Cc: Andrew Morton Signed-off-by: Linus Torvalds --- {include/asm-h8300 => arch/h8300/include/asm}/Kbuild | 0 {include/asm-h8300 => arch/h8300/include/asm}/a.out.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/atomic.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/auxvec.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/bitops.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/bootinfo.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/bug.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/bugs.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/byteorder.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/cache.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/cachectl.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/cacheflush.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/checksum.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/cputime.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/current.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/dbg.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/delay.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/device.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/div64.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/dma.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/elf.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/emergency-restart.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/errno.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/fb.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/fcntl.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/flat.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/fpu.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/futex.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/gpio.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/hardirq.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/hw_irq.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/io.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/ioctl.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/ioctls.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/ipcbuf.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/irq.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/irq_regs.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/kdebug.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/kmap_types.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/linkage.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/local.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/mc146818rtc.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/md.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/mman.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/mmu.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/mmu_context.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/module.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/msgbuf.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/mutex.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/page.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/page_offset.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/param.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/pci.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/percpu.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/pgalloc.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/pgtable.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/poll.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/posix_types.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/processor.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/ptrace.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/regs267x.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/regs306x.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/resource.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/scatterlist.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/sections.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/segment.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/sembuf.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/setup.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/sh_bios.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/shm.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/shmbuf.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/shmparam.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/sigcontext.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/siginfo.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/signal.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/smp.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/socket.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/sockios.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/spinlock.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/stat.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/statfs.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/string.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/system.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/target_time.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/termbits.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/termios.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/thread_info.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/timex.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/tlb.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/tlbflush.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/topology.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/traps.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/types.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/uaccess.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/ucontext.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/unaligned.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/unistd.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/user.h | 0 {include/asm-h8300 => arch/h8300/include/asm}/virtconvert.h | 0 99 files changed, 0 insertions(+), 0 deletions(-) rename {include/asm-h8300 => arch/h8300/include/asm}/Kbuild (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/a.out.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/atomic.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/auxvec.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/bitops.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/bootinfo.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/bug.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/bugs.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/byteorder.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/cache.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/cachectl.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/cacheflush.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/checksum.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/cputime.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/current.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/dbg.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/delay.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/device.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/div64.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/dma.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/elf.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/emergency-restart.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/errno.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/fb.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/fcntl.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/flat.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/fpu.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/futex.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/gpio.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/hardirq.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/hw_irq.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/io.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/ioctl.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/ioctls.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/ipcbuf.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/irq.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/irq_regs.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/kdebug.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/kmap_types.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/linkage.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/local.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/mc146818rtc.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/md.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/mman.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/mmu.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/mmu_context.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/module.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/msgbuf.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/mutex.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/page.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/page_offset.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/param.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/pci.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/percpu.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/pgalloc.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/pgtable.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/poll.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/posix_types.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/processor.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/ptrace.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/regs267x.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/regs306x.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/resource.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/scatterlist.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/sections.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/segment.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/sembuf.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/setup.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/sh_bios.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/shm.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/shmbuf.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/shmparam.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/sigcontext.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/siginfo.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/signal.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/smp.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/socket.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/sockios.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/spinlock.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/stat.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/statfs.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/string.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/system.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/target_time.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/termbits.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/termios.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/thread_info.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/timex.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/tlb.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/tlbflush.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/topology.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/traps.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/types.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/uaccess.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/ucontext.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/unaligned.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/unistd.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/user.h (100%) rename {include/asm-h8300 => arch/h8300/include/asm}/virtconvert.h (100%) diff --git a/include/asm-h8300/Kbuild b/arch/h8300/include/asm/Kbuild similarity index 100% rename from include/asm-h8300/Kbuild rename to arch/h8300/include/asm/Kbuild diff --git a/include/asm-h8300/a.out.h b/arch/h8300/include/asm/a.out.h similarity index 100% rename from include/asm-h8300/a.out.h rename to arch/h8300/include/asm/a.out.h diff --git a/include/asm-h8300/atomic.h b/arch/h8300/include/asm/atomic.h similarity index 100% rename from include/asm-h8300/atomic.h rename to arch/h8300/include/asm/atomic.h diff --git a/include/asm-h8300/auxvec.h b/arch/h8300/include/asm/auxvec.h similarity index 100% rename from include/asm-h8300/auxvec.h rename to arch/h8300/include/asm/auxvec.h diff --git a/include/asm-h8300/bitops.h b/arch/h8300/include/asm/bitops.h similarity index 100% rename from include/asm-h8300/bitops.h rename to arch/h8300/include/asm/bitops.h diff --git a/include/asm-h8300/bootinfo.h b/arch/h8300/include/asm/bootinfo.h similarity index 100% rename from include/asm-h8300/bootinfo.h rename to arch/h8300/include/asm/bootinfo.h diff --git a/include/asm-h8300/bug.h b/arch/h8300/include/asm/bug.h similarity index 100% rename from include/asm-h8300/bug.h rename to arch/h8300/include/asm/bug.h diff --git a/include/asm-h8300/bugs.h b/arch/h8300/include/asm/bugs.h similarity index 100% rename from include/asm-h8300/bugs.h rename to arch/h8300/include/asm/bugs.h diff --git a/include/asm-h8300/byteorder.h b/arch/h8300/include/asm/byteorder.h similarity index 100% rename from include/asm-h8300/byteorder.h rename to arch/h8300/include/asm/byteorder.h diff --git a/include/asm-h8300/cache.h b/arch/h8300/include/asm/cache.h similarity index 100% rename from include/asm-h8300/cache.h rename to arch/h8300/include/asm/cache.h diff --git a/include/asm-h8300/cachectl.h b/arch/h8300/include/asm/cachectl.h similarity index 100% rename from include/asm-h8300/cachectl.h rename to arch/h8300/include/asm/cachectl.h diff --git a/include/asm-h8300/cacheflush.h b/arch/h8300/include/asm/cacheflush.h similarity index 100% rename from include/asm-h8300/cacheflush.h rename to arch/h8300/include/asm/cacheflush.h diff --git a/include/asm-h8300/checksum.h b/arch/h8300/include/asm/checksum.h similarity index 100% rename from include/asm-h8300/checksum.h rename to arch/h8300/include/asm/checksum.h diff --git a/include/asm-h8300/cputime.h b/arch/h8300/include/asm/cputime.h similarity index 100% rename from include/asm-h8300/cputime.h rename to arch/h8300/include/asm/cputime.h diff --git a/include/asm-h8300/current.h b/arch/h8300/include/asm/current.h similarity index 100% rename from include/asm-h8300/current.h rename to arch/h8300/include/asm/current.h diff --git a/include/asm-h8300/dbg.h b/arch/h8300/include/asm/dbg.h similarity index 100% rename from include/asm-h8300/dbg.h rename to arch/h8300/include/asm/dbg.h diff --git a/include/asm-h8300/delay.h b/arch/h8300/include/asm/delay.h similarity index 100% rename from include/asm-h8300/delay.h rename to arch/h8300/include/asm/delay.h diff --git a/include/asm-h8300/device.h b/arch/h8300/include/asm/device.h similarity index 100% rename from include/asm-h8300/device.h rename to arch/h8300/include/asm/device.h diff --git a/include/asm-h8300/div64.h b/arch/h8300/include/asm/div64.h similarity index 100% rename from include/asm-h8300/div64.h rename to arch/h8300/include/asm/div64.h diff --git a/include/asm-h8300/dma.h b/arch/h8300/include/asm/dma.h similarity index 100% rename from include/asm-h8300/dma.h rename to arch/h8300/include/asm/dma.h diff --git a/include/asm-h8300/elf.h b/arch/h8300/include/asm/elf.h similarity index 100% rename from include/asm-h8300/elf.h rename to arch/h8300/include/asm/elf.h diff --git a/include/asm-h8300/emergency-restart.h b/arch/h8300/include/asm/emergency-restart.h similarity index 100% rename from include/asm-h8300/emergency-restart.h rename to arch/h8300/include/asm/emergency-restart.h diff --git a/include/asm-h8300/errno.h b/arch/h8300/include/asm/errno.h similarity index 100% rename from include/asm-h8300/errno.h rename to arch/h8300/include/asm/errno.h diff --git a/include/asm-h8300/fb.h b/arch/h8300/include/asm/fb.h similarity index 100% rename from include/asm-h8300/fb.h rename to arch/h8300/include/asm/fb.h diff --git a/include/asm-h8300/fcntl.h b/arch/h8300/include/asm/fcntl.h similarity index 100% rename from include/asm-h8300/fcntl.h rename to arch/h8300/include/asm/fcntl.h diff --git a/include/asm-h8300/flat.h b/arch/h8300/include/asm/flat.h similarity index 100% rename from include/asm-h8300/flat.h rename to arch/h8300/include/asm/flat.h diff --git a/include/asm-h8300/fpu.h b/arch/h8300/include/asm/fpu.h similarity index 100% rename from include/asm-h8300/fpu.h rename to arch/h8300/include/asm/fpu.h diff --git a/include/asm-h8300/futex.h b/arch/h8300/include/asm/futex.h similarity index 100% rename from include/asm-h8300/futex.h rename to arch/h8300/include/asm/futex.h diff --git a/include/asm-h8300/gpio.h b/arch/h8300/include/asm/gpio.h similarity index 100% rename from include/asm-h8300/gpio.h rename to arch/h8300/include/asm/gpio.h diff --git a/include/asm-h8300/hardirq.h b/arch/h8300/include/asm/hardirq.h similarity index 100% rename from include/asm-h8300/hardirq.h rename to arch/h8300/include/asm/hardirq.h diff --git a/include/asm-h8300/hw_irq.h b/arch/h8300/include/asm/hw_irq.h similarity index 100% rename from include/asm-h8300/hw_irq.h rename to arch/h8300/include/asm/hw_irq.h diff --git a/include/asm-h8300/io.h b/arch/h8300/include/asm/io.h similarity index 100% rename from include/asm-h8300/io.h rename to arch/h8300/include/asm/io.h diff --git a/include/asm-h8300/ioctl.h b/arch/h8300/include/asm/ioctl.h similarity index 100% rename from include/asm-h8300/ioctl.h rename to arch/h8300/include/asm/ioctl.h diff --git a/include/asm-h8300/ioctls.h b/arch/h8300/include/asm/ioctls.h similarity index 100% rename from include/asm-h8300/ioctls.h rename to arch/h8300/include/asm/ioctls.h diff --git a/include/asm-h8300/ipcbuf.h b/arch/h8300/include/asm/ipcbuf.h similarity index 100% rename from include/asm-h8300/ipcbuf.h rename to arch/h8300/include/asm/ipcbuf.h diff --git a/include/asm-h8300/irq.h b/arch/h8300/include/asm/irq.h similarity index 100% rename from include/asm-h8300/irq.h rename to arch/h8300/include/asm/irq.h diff --git a/include/asm-h8300/irq_regs.h b/arch/h8300/include/asm/irq_regs.h similarity index 100% rename from include/asm-h8300/irq_regs.h rename to arch/h8300/include/asm/irq_regs.h diff --git a/include/asm-h8300/kdebug.h b/arch/h8300/include/asm/kdebug.h similarity index 100% rename from include/asm-h8300/kdebug.h rename to arch/h8300/include/asm/kdebug.h diff --git a/include/asm-h8300/kmap_types.h b/arch/h8300/include/asm/kmap_types.h similarity index 100% rename from include/asm-h8300/kmap_types.h rename to arch/h8300/include/asm/kmap_types.h diff --git a/include/asm-h8300/linkage.h b/arch/h8300/include/asm/linkage.h similarity index 100% rename from include/asm-h8300/linkage.h rename to arch/h8300/include/asm/linkage.h diff --git a/include/asm-h8300/local.h b/arch/h8300/include/asm/local.h similarity index 100% rename from include/asm-h8300/local.h rename to arch/h8300/include/asm/local.h diff --git a/include/asm-h8300/mc146818rtc.h b/arch/h8300/include/asm/mc146818rtc.h similarity index 100% rename from include/asm-h8300/mc146818rtc.h rename to arch/h8300/include/asm/mc146818rtc.h diff --git a/include/asm-h8300/md.h b/arch/h8300/include/asm/md.h similarity index 100% rename from include/asm-h8300/md.h rename to arch/h8300/include/asm/md.h diff --git a/include/asm-h8300/mman.h b/arch/h8300/include/asm/mman.h similarity index 100% rename from include/asm-h8300/mman.h rename to arch/h8300/include/asm/mman.h diff --git a/include/asm-h8300/mmu.h b/arch/h8300/include/asm/mmu.h similarity index 100% rename from include/asm-h8300/mmu.h rename to arch/h8300/include/asm/mmu.h diff --git a/include/asm-h8300/mmu_context.h b/arch/h8300/include/asm/mmu_context.h similarity index 100% rename from include/asm-h8300/mmu_context.h rename to arch/h8300/include/asm/mmu_context.h diff --git a/include/asm-h8300/module.h b/arch/h8300/include/asm/module.h similarity index 100% rename from include/asm-h8300/module.h rename to arch/h8300/include/asm/module.h diff --git a/include/asm-h8300/msgbuf.h b/arch/h8300/include/asm/msgbuf.h similarity index 100% rename from include/asm-h8300/msgbuf.h rename to arch/h8300/include/asm/msgbuf.h diff --git a/include/asm-h8300/mutex.h b/arch/h8300/include/asm/mutex.h similarity index 100% rename from include/asm-h8300/mutex.h rename to arch/h8300/include/asm/mutex.h diff --git a/include/asm-h8300/page.h b/arch/h8300/include/asm/page.h similarity index 100% rename from include/asm-h8300/page.h rename to arch/h8300/include/asm/page.h diff --git a/include/asm-h8300/page_offset.h b/arch/h8300/include/asm/page_offset.h similarity index 100% rename from include/asm-h8300/page_offset.h rename to arch/h8300/include/asm/page_offset.h diff --git a/include/asm-h8300/param.h b/arch/h8300/include/asm/param.h similarity index 100% rename from include/asm-h8300/param.h rename to arch/h8300/include/asm/param.h diff --git a/include/asm-h8300/pci.h b/arch/h8300/include/asm/pci.h similarity index 100% rename from include/asm-h8300/pci.h rename to arch/h8300/include/asm/pci.h diff --git a/include/asm-h8300/percpu.h b/arch/h8300/include/asm/percpu.h similarity index 100% rename from include/asm-h8300/percpu.h rename to arch/h8300/include/asm/percpu.h diff --git a/include/asm-h8300/pgalloc.h b/arch/h8300/include/asm/pgalloc.h similarity index 100% rename from include/asm-h8300/pgalloc.h rename to arch/h8300/include/asm/pgalloc.h diff --git a/include/asm-h8300/pgtable.h b/arch/h8300/include/asm/pgtable.h similarity index 100% rename from include/asm-h8300/pgtable.h rename to arch/h8300/include/asm/pgtable.h diff --git a/include/asm-h8300/poll.h b/arch/h8300/include/asm/poll.h similarity index 100% rename from include/asm-h8300/poll.h rename to arch/h8300/include/asm/poll.h diff --git a/include/asm-h8300/posix_types.h b/arch/h8300/include/asm/posix_types.h similarity index 100% rename from include/asm-h8300/posix_types.h rename to arch/h8300/include/asm/posix_types.h diff --git a/include/asm-h8300/processor.h b/arch/h8300/include/asm/processor.h similarity index 100% rename from include/asm-h8300/processor.h rename to arch/h8300/include/asm/processor.h diff --git a/include/asm-h8300/ptrace.h b/arch/h8300/include/asm/ptrace.h similarity index 100% rename from include/asm-h8300/ptrace.h rename to arch/h8300/include/asm/ptrace.h diff --git a/include/asm-h8300/regs267x.h b/arch/h8300/include/asm/regs267x.h similarity index 100% rename from include/asm-h8300/regs267x.h rename to arch/h8300/include/asm/regs267x.h diff --git a/include/asm-h8300/regs306x.h b/arch/h8300/include/asm/regs306x.h similarity index 100% rename from include/asm-h8300/regs306x.h rename to arch/h8300/include/asm/regs306x.h diff --git a/include/asm-h8300/resource.h b/arch/h8300/include/asm/resource.h similarity index 100% rename from include/asm-h8300/resource.h rename to arch/h8300/include/asm/resource.h diff --git a/include/asm-h8300/scatterlist.h b/arch/h8300/include/asm/scatterlist.h similarity index 100% rename from include/asm-h8300/scatterlist.h rename to arch/h8300/include/asm/scatterlist.h diff --git a/include/asm-h8300/sections.h b/arch/h8300/include/asm/sections.h similarity index 100% rename from include/asm-h8300/sections.h rename to arch/h8300/include/asm/sections.h diff --git a/include/asm-h8300/segment.h b/arch/h8300/include/asm/segment.h similarity index 100% rename from include/asm-h8300/segment.h rename to arch/h8300/include/asm/segment.h diff --git a/include/asm-h8300/sembuf.h b/arch/h8300/include/asm/sembuf.h similarity index 100% rename from include/asm-h8300/sembuf.h rename to arch/h8300/include/asm/sembuf.h diff --git a/include/asm-h8300/setup.h b/arch/h8300/include/asm/setup.h similarity index 100% rename from include/asm-h8300/setup.h rename to arch/h8300/include/asm/setup.h diff --git a/include/asm-h8300/sh_bios.h b/arch/h8300/include/asm/sh_bios.h similarity index 100% rename from include/asm-h8300/sh_bios.h rename to arch/h8300/include/asm/sh_bios.h diff --git a/include/asm-h8300/shm.h b/arch/h8300/include/asm/shm.h similarity index 100% rename from include/asm-h8300/shm.h rename to arch/h8300/include/asm/shm.h diff --git a/include/asm-h8300/shmbuf.h b/arch/h8300/include/asm/shmbuf.h similarity index 100% rename from include/asm-h8300/shmbuf.h rename to arch/h8300/include/asm/shmbuf.h diff --git a/include/asm-h8300/shmparam.h b/arch/h8300/include/asm/shmparam.h similarity index 100% rename from include/asm-h8300/shmparam.h rename to arch/h8300/include/asm/shmparam.h diff --git a/include/asm-h8300/sigcontext.h b/arch/h8300/include/asm/sigcontext.h similarity index 100% rename from include/asm-h8300/sigcontext.h rename to arch/h8300/include/asm/sigcontext.h diff --git a/include/asm-h8300/siginfo.h b/arch/h8300/include/asm/siginfo.h similarity index 100% rename from include/asm-h8300/siginfo.h rename to arch/h8300/include/asm/siginfo.h diff --git a/include/asm-h8300/signal.h b/arch/h8300/include/asm/signal.h similarity index 100% rename from include/asm-h8300/signal.h rename to arch/h8300/include/asm/signal.h diff --git a/include/asm-h8300/smp.h b/arch/h8300/include/asm/smp.h similarity index 100% rename from include/asm-h8300/smp.h rename to arch/h8300/include/asm/smp.h diff --git a/include/asm-h8300/socket.h b/arch/h8300/include/asm/socket.h similarity index 100% rename from include/asm-h8300/socket.h rename to arch/h8300/include/asm/socket.h diff --git a/include/asm-h8300/sockios.h b/arch/h8300/include/asm/sockios.h similarity index 100% rename from include/asm-h8300/sockios.h rename to arch/h8300/include/asm/sockios.h diff --git a/include/asm-h8300/spinlock.h b/arch/h8300/include/asm/spinlock.h similarity index 100% rename from include/asm-h8300/spinlock.h rename to arch/h8300/include/asm/spinlock.h diff --git a/include/asm-h8300/stat.h b/arch/h8300/include/asm/stat.h similarity index 100% rename from include/asm-h8300/stat.h rename to arch/h8300/include/asm/stat.h diff --git a/include/asm-h8300/statfs.h b/arch/h8300/include/asm/statfs.h similarity index 100% rename from include/asm-h8300/statfs.h rename to arch/h8300/include/asm/statfs.h diff --git a/include/asm-h8300/string.h b/arch/h8300/include/asm/string.h similarity index 100% rename from include/asm-h8300/string.h rename to arch/h8300/include/asm/string.h diff --git a/include/asm-h8300/system.h b/arch/h8300/include/asm/system.h similarity index 100% rename from include/asm-h8300/system.h rename to arch/h8300/include/asm/system.h diff --git a/include/asm-h8300/target_time.h b/arch/h8300/include/asm/target_time.h similarity index 100% rename from include/asm-h8300/target_time.h rename to arch/h8300/include/asm/target_time.h diff --git a/include/asm-h8300/termbits.h b/arch/h8300/include/asm/termbits.h similarity index 100% rename from include/asm-h8300/termbits.h rename to arch/h8300/include/asm/termbits.h diff --git a/include/asm-h8300/termios.h b/arch/h8300/include/asm/termios.h similarity index 100% rename from include/asm-h8300/termios.h rename to arch/h8300/include/asm/termios.h diff --git a/include/asm-h8300/thread_info.h b/arch/h8300/include/asm/thread_info.h similarity index 100% rename from include/asm-h8300/thread_info.h rename to arch/h8300/include/asm/thread_info.h diff --git a/include/asm-h8300/timex.h b/arch/h8300/include/asm/timex.h similarity index 100% rename from include/asm-h8300/timex.h rename to arch/h8300/include/asm/timex.h diff --git a/include/asm-h8300/tlb.h b/arch/h8300/include/asm/tlb.h similarity index 100% rename from include/asm-h8300/tlb.h rename to arch/h8300/include/asm/tlb.h diff --git a/include/asm-h8300/tlbflush.h b/arch/h8300/include/asm/tlbflush.h similarity index 100% rename from include/asm-h8300/tlbflush.h rename to arch/h8300/include/asm/tlbflush.h diff --git a/include/asm-h8300/topology.h b/arch/h8300/include/asm/topology.h similarity index 100% rename from include/asm-h8300/topology.h rename to arch/h8300/include/asm/topology.h diff --git a/include/asm-h8300/traps.h b/arch/h8300/include/asm/traps.h similarity index 100% rename from include/asm-h8300/traps.h rename to arch/h8300/include/asm/traps.h diff --git a/include/asm-h8300/types.h b/arch/h8300/include/asm/types.h similarity index 100% rename from include/asm-h8300/types.h rename to arch/h8300/include/asm/types.h diff --git a/include/asm-h8300/uaccess.h b/arch/h8300/include/asm/uaccess.h similarity index 100% rename from include/asm-h8300/uaccess.h rename to arch/h8300/include/asm/uaccess.h diff --git a/include/asm-h8300/ucontext.h b/arch/h8300/include/asm/ucontext.h similarity index 100% rename from include/asm-h8300/ucontext.h rename to arch/h8300/include/asm/ucontext.h diff --git a/include/asm-h8300/unaligned.h b/arch/h8300/include/asm/unaligned.h similarity index 100% rename from include/asm-h8300/unaligned.h rename to arch/h8300/include/asm/unaligned.h diff --git a/include/asm-h8300/unistd.h b/arch/h8300/include/asm/unistd.h similarity index 100% rename from include/asm-h8300/unistd.h rename to arch/h8300/include/asm/unistd.h diff --git a/include/asm-h8300/user.h b/arch/h8300/include/asm/user.h similarity index 100% rename from include/asm-h8300/user.h rename to arch/h8300/include/asm/user.h diff --git a/include/asm-h8300/virtconvert.h b/arch/h8300/include/asm/virtconvert.h similarity index 100% rename from include/asm-h8300/virtconvert.h rename to arch/h8300/include/asm/virtconvert.h -- GitLab From c2dcfde8274883e1f6050784dcbd34b01e824b91 Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Wed, 13 Aug 2008 13:14:22 -0700 Subject: [PATCH 239/750] x86: cleanup for setup code crashes during IST probe Clean up the code for crashes during SpeedStep probing on older machines. Signed-off-by: H. Peter Anvin Signed-off-by: Ingo Molnar --- arch/x86/boot/boot.h | 4 ++-- arch/x86/boot/cpu.c | 3 --- arch/x86/boot/cpucheck.c | 2 -- arch/x86/boot/main.c | 3 ++- 4 files changed, 4 insertions(+), 8 deletions(-) diff --git a/arch/x86/boot/boot.h b/arch/x86/boot/boot.h index 9d4b4b43d97..616b804a229 100644 --- a/arch/x86/boot/boot.h +++ b/arch/x86/boot/boot.h @@ -24,8 +24,8 @@ #include #include #include - -#define NCAPINTS 8 +#include "bitops.h" +#include /* Useful macros */ #define BUILD_BUG_ON(condition) ((void)sizeof(char[1 - 2*!!(condition)])) diff --git a/arch/x86/boot/cpu.c b/arch/x86/boot/cpu.c index 92d6fd73dc7..75298fe2edc 100644 --- a/arch/x86/boot/cpu.c +++ b/arch/x86/boot/cpu.c @@ -16,9 +16,6 @@ */ #include "boot.h" -#include "bitops.h" -#include - #include "cpustr.h" static char *cpu_name(int level) diff --git a/arch/x86/boot/cpucheck.c b/arch/x86/boot/cpucheck.c index c1ce0303d99..4b9ae7c5674 100644 --- a/arch/x86/boot/cpucheck.c +++ b/arch/x86/boot/cpucheck.c @@ -22,10 +22,8 @@ #ifdef _SETUP # include "boot.h" -# include "bitops.h" #endif #include -#include #include #include #include diff --git a/arch/x86/boot/main.c b/arch/x86/boot/main.c index 01aa64b5575..197421db1af 100644 --- a/arch/x86/boot/main.c +++ b/arch/x86/boot/main.c @@ -73,7 +73,8 @@ static void keyboard_set_repeat(void) */ static void query_ist(void) { - /* Some 486 BIOSes apparently crash on this call */ + /* Some older BIOSes apparently crash on this call, so filter + it from machines too old to have SpeedStep at all. */ if (cpu.level < 6) return; -- GitLab From 64c00d81b5c2491bd140b3c8eb2e8c351513f971 Mon Sep 17 00:00:00 2001 From: Andrew Gallatin Date: Wed, 13 Aug 2008 15:16:00 -0700 Subject: [PATCH 240/750] pktgen: prevent pktgen from using bad tx queue With the new multi-queue transmit code, it is possible to accidentally make pktgen pick a non-existing tx queue simply by using a stale script to drive pktgen. Access to this non-existing tx queue will then trigger a bad memory access and kill the machine. For example, setting "queue_map_max 2" will cause my machine to die when accessing a garbage spinlock in the non-existing tx queue: BUG: spinlock bad magic on CPU#0, kpktgend_0/564 lock: ffff88001ddf6718, .magic: ffffffff, .owner: /-1, .owner_cpu: 0 Pid: 564, comm: kpktgend_0 Not tainted 2.6.27-rc3 #35 Call Trace: [] spin_bug+0xa4/0xac [] _raw_spin_lock+0x23/0x123 [] _spin_lock_bh+0x17/0x1b [] pktgen_thread_worker+0xa97/0x1002 [] ? finish_task_switch+0x38/0x97 [] ? autoremove_wake_function+0x0/0x36 [] ? autoremove_wake_function+0x0/0x36 [] ? pktgen_thread_worker+0x0/0x1002 [] kthread+0x44/0x6d [] child_rip+0xa/0x11 [] ? kthread+0x0/0x6d [] ? child_rip+0x0/0x11 The attached patch adds some sanity checking to prevent these sorts of configuration errors. Signed-off-by: Andrew Gallatin Signed-off-by: David S. Miller --- net/core/pktgen.c | 29 +++++++++++++++++++++++++++++ 1 file changed, 29 insertions(+) diff --git a/net/core/pktgen.c b/net/core/pktgen.c index 52623645390..a756847e381 100644 --- a/net/core/pktgen.c +++ b/net/core/pktgen.c @@ -1961,6 +1961,8 @@ static int pktgen_setup_dev(struct pktgen_dev *pkt_dev, const char *ifname) */ static void pktgen_setup_inject(struct pktgen_dev *pkt_dev) { + int ntxq; + if (!pkt_dev->odev) { printk(KERN_ERR "pktgen: ERROR: pkt_dev->odev == NULL in " "setup_inject.\n"); @@ -1969,6 +1971,33 @@ static void pktgen_setup_inject(struct pktgen_dev *pkt_dev) return; } + /* make sure that we don't pick a non-existing transmit queue */ + ntxq = pkt_dev->odev->real_num_tx_queues; + if (ntxq <= num_online_cpus() && (pkt_dev->flags & F_QUEUE_MAP_CPU)) { + printk(KERN_WARNING "pktgen: WARNING: QUEUE_MAP_CPU " + "disabled because CPU count (%d) exceeds number ", + num_online_cpus()); + printk(KERN_WARNING "pktgen: WARNING: of tx queues " + "(%d) on %s \n", ntxq, pkt_dev->odev->name); + pkt_dev->flags &= ~F_QUEUE_MAP_CPU; + } + if (ntxq <= pkt_dev->queue_map_min) { + printk(KERN_WARNING "pktgen: WARNING: Requested " + "queue_map_min (%d) exceeds number of tx\n", + pkt_dev->queue_map_min); + printk(KERN_WARNING "pktgen: WARNING: queues (%d) on " + "%s, resetting\n", ntxq, pkt_dev->odev->name); + pkt_dev->queue_map_min = ntxq - 1; + } + if (ntxq <= pkt_dev->queue_map_max) { + printk(KERN_WARNING "pktgen: WARNING: Requested " + "queue_map_max (%d) exceeds number of tx\n", + pkt_dev->queue_map_max); + printk(KERN_WARNING "pktgen: WARNING: queues (%d) on " + "%s, resetting\n", ntxq, pkt_dev->odev->name); + pkt_dev->queue_map_max = ntxq - 1; + } + /* Default to the interface's mac if not explicitly set. */ if (is_zero_ether_addr(pkt_dev->src_mac)) -- GitLab From 26b284de54a5ca3dfbe2fd9a51ac1923e80085a2 Mon Sep 17 00:00:00 2001 From: Jarek Poplawski Date: Wed, 13 Aug 2008 15:16:43 -0700 Subject: [PATCH 241/750] pkt_sched: Fix oops in htb_delete. Recent changes introduced a bug in htb_delete(): cl->parent->children counter update misses checking cl->parent for NULL, which is used for root classes, so deleting them causes an oops. Signed-off-by: Jarek Poplawski Signed-off-by: David S. Miller --- net/sched/sch_htb.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/net/sched/sch_htb.c b/net/sched/sch_htb.c index be35422711a..6febd245e62 100644 --- a/net/sched/sch_htb.c +++ b/net/sched/sch_htb.c @@ -1279,7 +1279,8 @@ static int htb_delete(struct Qdisc *sch, unsigned long arg) /* delete from hash and active; remainder in destroy_class */ qdisc_class_hash_remove(&q->clhash, &cl->common); - cl->parent->children--; + if (cl->parent) + cl->parent->children--; if (cl->prio_activity) htb_deactivate(q, cl); -- GitLab From b9a3b1102bc80b4044224494100f67de132d5448 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Wed, 13 Aug 2008 15:18:38 -0700 Subject: [PATCH 242/750] pkt_sched: Fix queue quiescence testing in dev_deactivate(). Based upon discussions with Jarek P. and Herbert Xu. First, we're testing the wrong qdisc. We just reset the device queue qdiscs to &noop_qdisc and checking it's state is completely pointless here. We want to wait until the previous qdisc that was sitting at the ->qdisc pointer is not busy any more. And that would be ->qdisc_sleeping. Because of how we propagate the samples qdisc pointer down into qdisc_run and friends via per-cpu ->output_queue and netif_schedule, we have to wait also for the __QDISC_STATE_SCHED bit to clear as well. Signed-off-by: David S. Miller --- net/sched/sch_generic.c | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-) diff --git a/net/sched/sch_generic.c b/net/sched/sch_generic.c index 7cf83b37459..468574682ca 100644 --- a/net/sched/sch_generic.c +++ b/net/sched/sch_generic.c @@ -647,7 +647,7 @@ static void dev_deactivate_queue(struct net_device *dev, } } -static bool some_qdisc_is_running(struct net_device *dev, int lock) +static bool some_qdisc_is_busy(struct net_device *dev, int lock) { unsigned int i; @@ -658,13 +658,14 @@ static bool some_qdisc_is_running(struct net_device *dev, int lock) int val; dev_queue = netdev_get_tx_queue(dev, i); - q = dev_queue->qdisc; + q = dev_queue->qdisc_sleeping; root_lock = qdisc_lock(q); if (lock) spin_lock_bh(root_lock); - val = test_bit(__QDISC_STATE_RUNNING, &q->state); + val = (test_bit(__QDISC_STATE_RUNNING, &q->state) || + test_bit(__QDISC_STATE_SCHED, &q->state)); if (lock) spin_unlock_bh(root_lock); @@ -689,14 +690,14 @@ void dev_deactivate(struct net_device *dev) /* Wait for outstanding qdisc_run calls. */ do { - while (some_qdisc_is_running(dev, 0)) + while (some_qdisc_is_busy(dev, 0)) yield(); /* * Double-check inside queue lock to ensure that all effects * of the queue run are visible when we return. */ - running = some_qdisc_is_running(dev, 1); + running = some_qdisc_is_busy(dev, 1); /* * The running flag should never be set at this point because -- GitLab From d4766692e72422f3b0f0e9ac6773d92baad07d51 Mon Sep 17 00:00:00 2001 From: Jarek Poplawski Date: Wed, 13 Aug 2008 15:20:24 -0700 Subject: [PATCH 243/750] pkt_sched: Protect gen estimators under est_lock. gen_kill_estimator() required rtnl_lock() protection, but since it is moved to an RCU callback __qdisc_destroy() let's use est_lock instead. Signed-off-by: Jarek Poplawski Signed-off-by: David S. Miller --- net/core/gen_estimator.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) diff --git a/net/core/gen_estimator.c b/net/core/gen_estimator.c index 57abe8266be..a89f32fa94f 100644 --- a/net/core/gen_estimator.c +++ b/net/core/gen_estimator.c @@ -99,7 +99,7 @@ struct gen_estimator_head static struct gen_estimator_head elist[EST_MAX_INTERVAL+1]; -/* Protects against NULL dereference */ +/* Protects against NULL dereference and RCU write-side */ static DEFINE_RWLOCK(est_lock); static void est_timer(unsigned long arg) @@ -185,6 +185,7 @@ int gen_new_estimator(struct gnet_stats_basic *bstats, est->last_packets = bstats->packets; est->avpps = rate_est->pps<<10; + write_lock_bh(&est_lock); if (!elist[idx].timer.function) { INIT_LIST_HEAD(&elist[idx].list); setup_timer(&elist[idx].timer, est_timer, idx); @@ -194,6 +195,7 @@ int gen_new_estimator(struct gnet_stats_basic *bstats, mod_timer(&elist[idx].timer, jiffies + ((HZ/4) << idx)); list_add_rcu(&est->list, &elist[idx].list); + write_unlock_bh(&est_lock); return 0; } @@ -212,7 +214,6 @@ static void __gen_kill_estimator(struct rcu_head *head) * Removes the rate estimator specified by &bstats and &rate_est * and deletes the timer. * - * NOTE: Called under rtnl_mutex */ void gen_kill_estimator(struct gnet_stats_basic *bstats, struct gnet_stats_rate_est *rate_est) @@ -226,17 +227,17 @@ void gen_kill_estimator(struct gnet_stats_basic *bstats, if (!elist[idx].timer.function) continue; + write_lock_bh(&est_lock); list_for_each_entry_safe(e, n, &elist[idx].list, list) { if (e->rate_est != rate_est || e->bstats != bstats) continue; - write_lock_bh(&est_lock); e->bstats = NULL; - write_unlock_bh(&est_lock); list_del_rcu(&e->list); call_rcu(&e->e_rcu, __gen_kill_estimator); } + write_unlock_bh(&est_lock); } } -- GitLab From 19680c4850c1e5c2b4371388637c7ce86b8570b6 Mon Sep 17 00:00:00 2001 From: Eilon Greenstein Date: Wed, 13 Aug 2008 15:47:33 -0700 Subject: [PATCH 244/750] bnx2x: FW (bootcode) interface fixes FW (bootcode) interface fixes - Making sure that the device will not cause kernel panic of the bootcode is corrupted or missing - Removing module debug parameter "nomcp" since no one should work without the bootcode (this is a left over from the chip bring up days) - Instead of waiting fix amount of time for bootcode response, sample it every 10ms (usually the answer is ready after less than 10ms) Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x_main.c | 74 +++++++++++++++++++++++----------------- 1 file changed, 42 insertions(+), 32 deletions(-) diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index 272a4bd2595..9eb8a3e6d62 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -76,23 +76,21 @@ MODULE_DESCRIPTION("Broadcom NetXtreme II BCM57710 Driver"); MODULE_LICENSE("GPL"); MODULE_VERSION(DRV_MODULE_VERSION); +static int disable_tpa; static int use_inta; static int poll; static int debug; -static int disable_tpa; -static int nomcp; static int load_count[3]; /* 0-common, 1-port0, 2-port1 */ static int use_multi; +module_param(disable_tpa, int, 0); module_param(use_inta, int, 0); module_param(poll, int, 0); module_param(debug, int, 0); -module_param(disable_tpa, int, 0); -module_param(nomcp, int, 0); +MODULE_PARM_DESC(disable_tpa, "disable the TPA (LRO) feature"); MODULE_PARM_DESC(use_inta, "use INT#A instead of MSI-X"); MODULE_PARM_DESC(poll, "use polling (for debug)"); MODULE_PARM_DESC(debug, "default debug msglevel"); -MODULE_PARM_DESC(nomcp, "ignore management CPU"); #ifdef BNX2X_MULTI module_param(use_multi, int, 0); @@ -1940,37 +1938,47 @@ static void bnx2x_link_report(struct bnx2x *bp) static u8 bnx2x_initial_phy_init(struct bnx2x *bp) { - u8 rc; + if (!BP_NOMCP(bp)) { + u8 rc; - /* Initialize link parameters structure variables */ - bp->link_params.mtu = bp->dev->mtu; + /* Initialize link parameters structure variables */ + bp->link_params.mtu = bp->dev->mtu; - bnx2x_phy_hw_lock(bp); - rc = bnx2x_phy_init(&bp->link_params, &bp->link_vars); - bnx2x_phy_hw_unlock(bp); + bnx2x_phy_hw_lock(bp); + rc = bnx2x_phy_init(&bp->link_params, &bp->link_vars); + bnx2x_phy_hw_unlock(bp); - if (bp->link_vars.link_up) - bnx2x_link_report(bp); + if (bp->link_vars.link_up) + bnx2x_link_report(bp); - bnx2x_calc_fc_adv(bp); + bnx2x_calc_fc_adv(bp); - return rc; + return rc; + } + BNX2X_ERR("Bootcode is missing -not initializing link\n"); + return -EINVAL; } static void bnx2x_link_set(struct bnx2x *bp) { - bnx2x_phy_hw_lock(bp); - bnx2x_phy_init(&bp->link_params, &bp->link_vars); - bnx2x_phy_hw_unlock(bp); + if (!BP_NOMCP(bp)) { + bnx2x_phy_hw_lock(bp); + bnx2x_phy_init(&bp->link_params, &bp->link_vars); + bnx2x_phy_hw_unlock(bp); - bnx2x_calc_fc_adv(bp); + bnx2x_calc_fc_adv(bp); + } else + BNX2X_ERR("Bootcode is missing -not setting link\n"); } static void bnx2x__link_reset(struct bnx2x *bp) { - bnx2x_phy_hw_lock(bp); - bnx2x_link_reset(&bp->link_params, &bp->link_vars); - bnx2x_phy_hw_unlock(bp); + if (!BP_NOMCP(bp)) { + bnx2x_phy_hw_lock(bp); + bnx2x_link_reset(&bp->link_params, &bp->link_vars); + bnx2x_phy_hw_unlock(bp); + } else + BNX2X_ERR("Bootcode is missing -not resetting link\n"); } static u8 bnx2x_link_test(struct bnx2x *bp) @@ -2374,7 +2382,7 @@ static int bnx2x_lock_alr(struct bnx2x *bp) msleep(5); } if (!(val & (1L << 31))) { - BNX2X_ERR("Cannot acquire nvram interface\n"); + BNX2X_ERR("Cannot acquire MCP access lock register\n"); rc = -EBUSY; } @@ -5638,18 +5646,23 @@ static u32 bnx2x_fw_command(struct bnx2x *bp, u32 command) int func = BP_FUNC(bp); u32 seq = ++bp->fw_seq; u32 rc = 0; + u32 cnt = 1; + u8 delay = CHIP_REV_IS_SLOW(bp) ? 100 : 10; SHMEM_WR(bp, func_mb[func].drv_mb_header, (command | seq)); DP(BNX2X_MSG_MCP, "wrote command (%x) to FW MB\n", (command | seq)); - /* let the FW do it's magic ... */ - msleep(100); /* TBD */ + do { + /* let the FW do it's magic ... */ + msleep(delay); + + rc = SHMEM_RD(bp, func_mb[func].fw_mb_header); - if (CHIP_REV_IS_SLOW(bp)) - msleep(900); + /* Give the FW up to 2 second (200*10ms) */ + } while ((seq != (rc & FW_MSG_SEQ_NUMBER_MASK)) && (cnt++ < 200)); - rc = SHMEM_RD(bp, func_mb[func].fw_mb_header); - DP(BNX2X_MSG_MCP, "read (%x) seq is (%x) from FW MB\n", rc, seq); + DP(BNX2X_MSG_MCP, "[after %d ms] read (%x) seq is (%x) from FW MB\n", + cnt*delay, rc, seq); /* is this a reply to our command? */ if (seq == (rc & FW_MSG_SEQ_NUMBER_MASK)) { @@ -7337,9 +7350,6 @@ static int __devinit bnx2x_init_bp(struct bnx2x *bp) int func = BP_FUNC(bp); int rc; - if (nomcp) - bp->flags |= NO_MCP_FLAG; - mutex_init(&bp->port.phy_mutex); INIT_WORK(&bp->sp_task, bnx2x_sp_task); -- GitLab From 1adcd8bee37f494e22aee856467e994ae086ae45 Mon Sep 17 00:00:00 2001 From: Eilon Greenstein Date: Wed, 13 Aug 2008 15:48:29 -0700 Subject: [PATCH 245/750] bnx2x: Not dropping packets with L3/L4 checksum error Not dropping packets with L3/L4 checksum error Those packets should be passed to the OS. The problem is clear in forwarding mode. Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x.h | 24 ++++++++++++++++-------- drivers/net/bnx2x_main.c | 7 +++---- 2 files changed, 19 insertions(+), 12 deletions(-) diff --git a/drivers/net/bnx2x.h b/drivers/net/bnx2x.h index 4bf4f7b205f..dc54602494f 100644 --- a/drivers/net/bnx2x.h +++ b/drivers/net/bnx2x.h @@ -386,20 +386,28 @@ struct bnx2x_fastpath { #define TPA_TYPE(cqe_fp_flags) ((cqe_fp_flags) & \ (TPA_TYPE_START | TPA_TYPE_END)) -#define BNX2X_RX_SUM_OK(cqe) \ - (!(cqe->fast_path_cqe.status_flags & \ - (ETH_FAST_PATH_RX_CQE_IP_XSUM_NO_VALIDATION_FLG | \ - ETH_FAST_PATH_RX_CQE_L4_XSUM_NO_VALIDATION_FLG))) +#define ETH_RX_ERROR_FALGS ETH_FAST_PATH_RX_CQE_PHY_DECODE_ERR_FLG + +#define BNX2X_IP_CSUM_ERR(cqe) \ + (!((cqe)->fast_path_cqe.status_flags & \ + ETH_FAST_PATH_RX_CQE_IP_XSUM_NO_VALIDATION_FLG) && \ + ((cqe)->fast_path_cqe.type_error_flags & \ + ETH_FAST_PATH_RX_CQE_IP_BAD_XSUM_FLG)) + +#define BNX2X_L4_CSUM_ERR(cqe) \ + (!((cqe)->fast_path_cqe.status_flags & \ + ETH_FAST_PATH_RX_CQE_L4_XSUM_NO_VALIDATION_FLG) && \ + ((cqe)->fast_path_cqe.type_error_flags & \ + ETH_FAST_PATH_RX_CQE_L4_BAD_XSUM_FLG)) + +#define BNX2X_RX_CSUM_OK(cqe) \ + (!(BNX2X_L4_CSUM_ERR(cqe) || BNX2X_IP_CSUM_ERR(cqe))) #define BNX2X_RX_SUM_FIX(cqe) \ ((le16_to_cpu(cqe->fast_path_cqe.pars_flags.flags) & \ PARSING_FLAGS_OVER_ETHERNET_PROTOCOL) == \ (1 << PARSING_FLAGS_OVER_ETHERNET_PROTOCOL_SHIFT)) -#define ETH_RX_ERROR_FALGS (ETH_FAST_PATH_RX_CQE_PHY_DECODE_ERR_FLG | \ - ETH_FAST_PATH_RX_CQE_IP_BAD_XSUM_FLG | \ - ETH_FAST_PATH_RX_CQE_L4_BAD_XSUM_FLG) - #define FP_USB_FUNC_OFF (2 + 2*HC_USTORM_SB_NUM_INDICES) #define FP_CSB_FUNC_OFF (2 + 2*HC_CSTORM_SB_NUM_INDICES) diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index 9eb8a3e6d62..b9d376d972c 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -1501,7 +1501,6 @@ static int bnx2x_rx_int(struct bnx2x_fastpath *fp, int budget) /* is this an error packet? */ if (unlikely(cqe_fp_flags & ETH_RX_ERROR_FALGS)) { - /* do we sometimes forward error packets anyway? */ DP(NETIF_MSG_RX_ERR, "ERROR flags %x rx packet %u\n", cqe_fp_flags, sw_comp_cons); @@ -1557,10 +1556,10 @@ reuse_rx: skb->protocol = eth_type_trans(skb, bp->dev); skb->ip_summed = CHECKSUM_NONE; - if (bp->rx_csum && BNX2X_RX_SUM_OK(cqe)) - skb->ip_summed = CHECKSUM_UNNECESSARY; + if (bp->rx_csum) + if (likely(BNX2X_RX_CSUM_OK(cqe))) + skb->ip_summed = CHECKSUM_UNNECESSARY; - /* TBD do we pass bad csum packets in promisc */ } #ifdef BCM_VLAN -- GitLab From 66e855f3f5197fec1162c5235fdb5f92b956d618 Mon Sep 17 00:00:00 2001 From: Yitchak Gertner Date: Wed, 13 Aug 2008 15:49:05 -0700 Subject: [PATCH 246/750] bnx2x: Statistics Statistics - Making sure that each drop is accounted for in the driver statistics - Clearing the FW statistics when driver is loaded to prevent inconsistency with HW statistics - Once error is detected (bnx2x_panic_dump), stop the statistics before other actions (currently it is stopped last and can corrupt the data) - Adding HW checksum error counter to the statistics - Removing unused variable stats_ticks - Using macros instead of magic numbers to indicate which statistics are shared per port and which are per function Signed-off-by: Yitchak Gertner Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x.h | 11 +- drivers/net/bnx2x_fw_defs.h | 6 + drivers/net/bnx2x_main.c | 228 ++++++++++++++++++++++-------------- drivers/net/bnx2x_reg.h | 3 + 4 files changed, 154 insertions(+), 94 deletions(-) diff --git a/drivers/net/bnx2x.h b/drivers/net/bnx2x.h index dc54602494f..9cbf0e82ef3 100644 --- a/drivers/net/bnx2x.h +++ b/drivers/net/bnx2x.h @@ -258,8 +258,7 @@ struct bnx2x_fastpath { unsigned long tx_pkt, rx_pkt, - rx_calls, - rx_alloc_failed; + rx_calls; /* TPA related */ struct sw_rx_bd tpa_pool[ETH_MAX_AGGREGATION_QUEUES_E1H]; u8 tpa_state[ETH_MAX_AGGREGATION_QUEUES_E1H]; @@ -655,6 +654,8 @@ struct bnx2x_eth_stats { u32 brb_drop_hi; u32 brb_drop_lo; + u32 brb_truncate_hi; + u32 brb_truncate_lo; u32 jabber_packets_received; @@ -671,6 +672,9 @@ struct bnx2x_eth_stats { u32 mac_discard; u32 driver_xoff; + u32 rx_err_discard_pkt; + u32 rx_skb_alloc_failed; + u32 hw_csum_err; }; #define STATS_OFFSET32(stat_name) \ @@ -844,7 +848,6 @@ struct bnx2x { u16 rx_ticks_int; u16 rx_ticks; - u32 stats_ticks; u32 lin_cnt; int state; @@ -984,7 +987,7 @@ static inline u32 reg_poll(struct bnx2x *bp, u32 reg, u32 expected, int ms, #define PCICFG_LINK_SPEED_SHIFT 16 -#define BNX2X_NUM_STATS 39 +#define BNX2X_NUM_STATS 42 #define BNX2X_NUM_TESTS 8 #define BNX2X_MAC_LOOPBACK 0 diff --git a/drivers/net/bnx2x_fw_defs.h b/drivers/net/bnx2x_fw_defs.h index e3da7f69d27..6e35761fc7d 100644 --- a/drivers/net/bnx2x_fw_defs.h +++ b/drivers/net/bnx2x_fw_defs.h @@ -79,6 +79,9 @@ #define TSTORM_MAC_FILTER_CONFIG_OFFSET(function) \ (IS_E1H_OFFSET? (0x3008 + (function * 0x38)) : (0x1508 + \ (function * 0x38))) +#define TSTORM_PER_COUNTER_ID_STATS_OFFSET(port, stats_counter_id) \ + (IS_E1H_OFFSET ? (0x2010 + (port * 0x5b0) + (stats_counter_id * \ + 0x50)) : (0x4000 + (port * 0x3f0) + (stats_counter_id * 0x38))) #define TSTORM_RX_PRODS_OFFSET(port, client_id) \ (IS_E1H_OFFSET? (0x3350 + (port * 0x3e8) + (client_id * 0x28)) : \ (0x9c0 + (port * 0x2f8) + (client_id * 0x28))) @@ -157,6 +160,9 @@ (IS_E1H_OFFSET? 0x2ac8 : 0xffffffff) #define XSTORM_HC_BTR_OFFSET(port) \ (IS_E1H_OFFSET? (0xa144 + (port * 0x30)) : (0x1454 + (port * 0x18))) +#define XSTORM_PER_COUNTER_ID_STATS_OFFSET(port, stats_counter_id) \ + (IS_E1H_OFFSET ? (0xc000 + (port * 0x3f0) + (stats_counter_id * \ + 0x38)) : (0x3378 + (port * 0x3f0) + (stats_counter_id * 0x38))) #define XSTORM_RATE_SHAPING_PER_VN_VARS_OFFSET(function) \ (IS_E1H_OFFSET? (0x2528 + (function * 0x70)) : (0x3c20 + \ (function * 0x70))) diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index b9d376d972c..ac46228cc9d 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -501,6 +501,9 @@ static void bnx2x_panic_dump(struct bnx2x *bp) int i; u16 j, start, end; + bp->stats_state = STATS_STATE_DISABLED; + DP(BNX2X_MSG_STATS, "stats_state - DISABLED\n"); + BNX2X_ERR("begin crash dump -----------------\n"); for_each_queue(bp, i) { @@ -511,17 +514,20 @@ static void bnx2x_panic_dump(struct bnx2x *bp) " tx_bd_prod(%x) tx_bd_cons(%x) *tx_cons_sb(%x)\n", i, fp->tx_pkt_prod, fp->tx_pkt_cons, fp->tx_bd_prod, fp->tx_bd_cons, le16_to_cpu(*fp->tx_cons_sb)); - BNX2X_ERR(" rx_comp_prod(%x) rx_comp_cons(%x)" - " *rx_cons_sb(%x) *rx_bd_cons_sb(%x)" - " rx_sge_prod(%x) last_max_sge(%x)\n", - fp->rx_comp_prod, fp->rx_comp_cons, - le16_to_cpu(*fp->rx_cons_sb), - le16_to_cpu(*fp->rx_bd_cons_sb), - fp->rx_sge_prod, fp->last_max_sge); - BNX2X_ERR(" fp_c_idx(%x) fp_u_idx(%x)" - " bd data(%x,%x) rx_alloc_failed(%lx)\n", - fp->fp_c_idx, fp->fp_u_idx, hw_prods->packets_prod, - hw_prods->bds_prod, fp->rx_alloc_failed); + BNX2X_ERR(" rx_bd_prod(%x) rx_bd_cons(%x)" + " *rx_bd_cons_sb(%x) rx_comp_prod(%x)" + " rx_comp_cons(%x) *rx_cons_sb(%x)\n", + fp->rx_bd_prod, fp->rx_bd_cons, + le16_to_cpu(*fp->rx_bd_cons_sb), fp->rx_comp_prod, + fp->rx_comp_cons, le16_to_cpu(*fp->rx_cons_sb)); + BNX2X_ERR(" rx_sge_prod(%x) last_max_sge(%x)" + " fp_c_idx(%x) *sb_c_idx(%x) fp_u_idx(%x)" + " *sb_u_idx(%x) bd data(%x,%x)\n", + fp->rx_sge_prod, fp->last_max_sge, fp->fp_c_idx, + fp->status_blk->c_status_block.status_block_index, + fp->fp_u_idx, + fp->status_blk->u_status_block.status_block_index, + hw_prods->packets_prod, hw_prods->bds_prod); start = TX_BD(le16_to_cpu(*fp->tx_cons_sb) - 10); end = TX_BD(le16_to_cpu(*fp->tx_cons_sb) + 245); @@ -580,9 +586,6 @@ static void bnx2x_panic_dump(struct bnx2x *bp) bnx2x_fw_dump(bp); bnx2x_mc_assert(bp); BNX2X_ERR("end crash dump -----------------\n"); - - bp->stats_state = STATS_STATE_DISABLED; - DP(BNX2X_MSG_STATS, "stats_state - DISABLED\n"); } static void bnx2x_int_enable(struct bnx2x *bp) @@ -1259,7 +1262,7 @@ static int bnx2x_fill_frag_skb(struct bnx2x *bp, struct bnx2x_fastpath *fp, where we are and drop the whole packet */ err = bnx2x_alloc_rx_sge(bp, fp, sge_idx); if (unlikely(err)) { - fp->rx_alloc_failed++; + bp->eth_stats.rx_skb_alloc_failed++; return err; } @@ -1295,14 +1298,13 @@ static void bnx2x_tpa_stop(struct bnx2x *bp, struct bnx2x_fastpath *fp, pci_unmap_single(bp->pdev, pci_unmap_addr(rx_buf, mapping), bp->rx_buf_use_size, PCI_DMA_FROMDEVICE); - /* if alloc failed drop the packet and keep the buffer in the bin */ if (likely(new_skb)) { + /* fix ip xsum and give it to the stack */ + /* (no need to map the new skb) */ prefetch(skb); prefetch(((char *)(skb)) + 128); - /* else fix ip xsum and give it to the stack */ - /* (no need to map the new skb) */ #ifdef BNX2X_STOP_ON_ERROR if (pad + len > bp->rx_buf_size) { BNX2X_ERR("skb_put is about to fail... " @@ -1351,9 +1353,10 @@ static void bnx2x_tpa_stop(struct bnx2x *bp, struct bnx2x_fastpath *fp, fp->tpa_pool[queue].skb = new_skb; } else { + /* else drop the packet and keep the buffer in the bin */ DP(NETIF_MSG_RX_STATUS, "Failed to allocate new skb - dropping packet!\n"); - fp->rx_alloc_failed++; + bp->eth_stats.rx_skb_alloc_failed++; } fp->tpa_state[queue] = BNX2X_TPA_STOP; @@ -1504,7 +1507,7 @@ static int bnx2x_rx_int(struct bnx2x_fastpath *fp, int budget) DP(NETIF_MSG_RX_ERR, "ERROR flags %x rx packet %u\n", cqe_fp_flags, sw_comp_cons); - /* TBD make sure MC counts this as a drop */ + bp->eth_stats.rx_err_discard_pkt++; goto reuse_rx; } @@ -1521,7 +1524,7 @@ static int bnx2x_rx_int(struct bnx2x_fastpath *fp, int budget) DP(NETIF_MSG_RX_ERR, "ERROR packet dropped " "because of alloc failure\n"); - fp->rx_alloc_failed++; + bp->eth_stats.rx_skb_alloc_failed++; goto reuse_rx; } @@ -1547,7 +1550,7 @@ static int bnx2x_rx_int(struct bnx2x_fastpath *fp, int budget) DP(NETIF_MSG_RX_ERR, "ERROR packet dropped because " "of alloc failure\n"); - fp->rx_alloc_failed++; + bp->eth_stats.rx_skb_alloc_failed++; reuse_rx: bnx2x_reuse_rx_skb(fp, skb, bd_cons, bd_prod); goto next_rx; @@ -1556,10 +1559,12 @@ reuse_rx: skb->protocol = eth_type_trans(skb, bp->dev); skb->ip_summed = CHECKSUM_NONE; - if (bp->rx_csum) + if (bp->rx_csum) { if (likely(BNX2X_RX_CSUM_OK(cqe))) skb->ip_summed = CHECKSUM_UNNECESSARY; - + else + bp->eth_stats.hw_csum_err++; + } } #ifdef BCM_VLAN @@ -3039,6 +3044,8 @@ static void bnx2x_stats_init(struct bnx2x *bp) memset(&(bp->port.old_nig_stats), 0, sizeof(struct nig_stats)); bp->port.old_nig_stats.brb_discard = REG_RD(bp, NIG_REG_STAT0_BRB_DISCARD + port*0x38); + bp->port.old_nig_stats.brb_truncate = + REG_RD(bp, NIG_REG_STAT0_BRB_TRUNCATE + port*0x38); REG_RD_DMAE(bp, NIG_REG_STAT0_EGRESS_MAC_PKT0 + port*0x50, &(bp->port.old_nig_stats.egress_mac_pkt0_lo), 2); REG_RD_DMAE(bp, NIG_REG_STAT0_EGRESS_MAC_PKT1 + port*0x50, @@ -3458,8 +3465,7 @@ static void bnx2x_bmac_stats_update(struct bnx2x *bp) UPDATE_STAT64(rx_stat_grovr, rx_stat_dot3statsframestoolong); UPDATE_STAT64(rx_stat_grfrg, rx_stat_etherstatsfragments); UPDATE_STAT64(rx_stat_grjbr, rx_stat_etherstatsjabbers); - UPDATE_STAT64(rx_stat_grxpf, rx_stat_bmac_xpf); - UPDATE_STAT64(rx_stat_grxcf, rx_stat_bmac_xcf); + UPDATE_STAT64(rx_stat_grxcf, rx_stat_maccontrolframesreceived); UPDATE_STAT64(rx_stat_grxpf, rx_stat_xoffstateentered); UPDATE_STAT64(rx_stat_grxpf, rx_stat_xoffpauseframesreceived); UPDATE_STAT64(tx_stat_gtxpf, tx_stat_outxoffsent); @@ -3543,6 +3549,8 @@ static int bnx2x_hw_stats_update(struct bnx2x *bp) ADD_EXTEND_64(pstats->brb_drop_hi, pstats->brb_drop_lo, new->brb_discard - old->brb_discard); + ADD_EXTEND_64(estats->brb_truncate_hi, estats->brb_truncate_lo, + new->brb_truncate - old->brb_truncate); UPDATE_STAT64_NIG(egress_mac_pkt0, etherstatspkts1024octetsto1522octets); @@ -3720,8 +3728,7 @@ static void bnx2x_net_stats_update(struct bnx2x *bp) nstats->rx_length_errors = estats->rx_stat_etherstatsundersizepkts_lo + estats->jabber_packets_received; - nstats->rx_over_errors = estats->brb_drop_lo + - estats->brb_truncate_discard; + nstats->rx_over_errors = estats->brb_drop_lo + estats->brb_truncate_lo; nstats->rx_crc_errors = estats->rx_stat_dot3statsfcserrors_lo; nstats->rx_frame_errors = estats->rx_stat_dot3statsalignmenterrors_lo; nstats->rx_fifo_errors = old_tclient->no_buff_discard; @@ -4201,6 +4208,7 @@ static void bnx2x_init_def_sb(struct bnx2x *bp, XSTORM_DEF_SB_HC_DISABLE_OFFSET(func, index), 1); bp->stats_pending = 0; + bp->set_mac_pending = 0; bnx2x_ack_sb(bp, sb_id, CSTORM_ID, 0, IGU_INT_ENABLE, 0); } @@ -4370,13 +4378,13 @@ static void bnx2x_init_rx_rings(struct bnx2x *bp) fp->rx_sge_prod = ring_prod; /* Allocate BDs and initialize BD ring */ - fp->rx_comp_cons = fp->rx_alloc_failed = 0; + fp->rx_comp_cons = 0; cqe_ring_prod = ring_prod = 0; for (i = 0; i < bp->rx_ring_size; i++) { if (bnx2x_alloc_rx_skb(bp, fp, ring_prod) < 0) { BNX2X_ERR("was only able to allocate " "%d rx skbs\n", i); - fp->rx_alloc_failed++; + bp->eth_stats.rx_skb_alloc_failed++; break; } ring_prod = NEXT_RX_IDX(ring_prod); @@ -4542,7 +4550,7 @@ static void bnx2x_set_client_config(struct bnx2x *bp) int i; tstorm_client.mtu = bp->dev->mtu + ETH_OVREHEAD; - tstorm_client.statistics_counter_id = 0; + tstorm_client.statistics_counter_id = BP_CL_ID(bp); tstorm_client.config_flags = TSTORM_ETH_CLIENT_CONFIG_STATSITICS_ENABLE; #ifdef BCM_VLAN @@ -4649,25 +4657,50 @@ static void bnx2x_init_internal(struct bnx2x *bp) bp->rx_mode = BNX2X_RX_MODE_NONE; /* no rx until link is up */ bnx2x_set_storm_rx_mode(bp); + /* reset xstorm per client statistics */ + for (i = 0; i < sizeof(struct xstorm_per_client_stats) / 4; i++) { + REG_WR(bp, BAR_XSTRORM_INTMEM + + XSTORM_PER_COUNTER_ID_STATS_OFFSET(port, BP_CL_ID(bp)) + + i*4, 0); + } + /* reset tstorm per client statistics */ + for (i = 0; i < sizeof(struct tstorm_per_client_stats) / 4; i++) { + REG_WR(bp, BAR_TSTRORM_INTMEM + + TSTORM_PER_COUNTER_ID_STATS_OFFSET(port, BP_CL_ID(bp)) + + i*4, 0); + } + + /* Init statistics related context */ stats_flags.collect_eth = 1; - REG_WR(bp, BAR_XSTRORM_INTMEM + XSTORM_STATS_FLAGS_OFFSET(port), + REG_WR(bp, BAR_XSTRORM_INTMEM + XSTORM_STATS_FLAGS_OFFSET(func), ((u32 *)&stats_flags)[0]); - REG_WR(bp, BAR_XSTRORM_INTMEM + XSTORM_STATS_FLAGS_OFFSET(port) + 4, + REG_WR(bp, BAR_XSTRORM_INTMEM + XSTORM_STATS_FLAGS_OFFSET(func) + 4, ((u32 *)&stats_flags)[1]); - REG_WR(bp, BAR_TSTRORM_INTMEM + TSTORM_STATS_FLAGS_OFFSET(port), + REG_WR(bp, BAR_TSTRORM_INTMEM + TSTORM_STATS_FLAGS_OFFSET(func), ((u32 *)&stats_flags)[0]); - REG_WR(bp, BAR_TSTRORM_INTMEM + TSTORM_STATS_FLAGS_OFFSET(port) + 4, + REG_WR(bp, BAR_TSTRORM_INTMEM + TSTORM_STATS_FLAGS_OFFSET(func) + 4, ((u32 *)&stats_flags)[1]); - REG_WR(bp, BAR_CSTRORM_INTMEM + CSTORM_STATS_FLAGS_OFFSET(port), + REG_WR(bp, BAR_CSTRORM_INTMEM + CSTORM_STATS_FLAGS_OFFSET(func), ((u32 *)&stats_flags)[0]); - REG_WR(bp, BAR_CSTRORM_INTMEM + CSTORM_STATS_FLAGS_OFFSET(port) + 4, + REG_WR(bp, BAR_CSTRORM_INTMEM + CSTORM_STATS_FLAGS_OFFSET(func) + 4, ((u32 *)&stats_flags)[1]); -/* DP(NETIF_MSG_IFUP, "stats_flags: 0x%08x 0x%08x\n", - ((u32 *)&stats_flags)[0], ((u32 *)&stats_flags)[1]); */ + REG_WR(bp, BAR_XSTRORM_INTMEM + + XSTORM_ETH_STATS_QUERY_ADDR_OFFSET(func), + U64_LO(bnx2x_sp_mapping(bp, fw_stats))); + REG_WR(bp, BAR_XSTRORM_INTMEM + + XSTORM_ETH_STATS_QUERY_ADDR_OFFSET(func) + 4, + U64_HI(bnx2x_sp_mapping(bp, fw_stats))); + + REG_WR(bp, BAR_TSTRORM_INTMEM + + TSTORM_ETH_STATS_QUERY_ADDR_OFFSET(func), + U64_LO(bnx2x_sp_mapping(bp, fw_stats))); + REG_WR(bp, BAR_TSTRORM_INTMEM + + TSTORM_ETH_STATS_QUERY_ADDR_OFFSET(func) + 4, + U64_HI(bnx2x_sp_mapping(bp, fw_stats))); if (CHIP_IS_E1H(bp)) { REG_WR8(bp, BAR_XSTRORM_INTMEM + XSTORM_FUNCTION_MODE_OFFSET, @@ -7386,8 +7419,6 @@ static int __devinit bnx2x_init_bp(struct bnx2x *bp) bp->tx_ticks = 50; bp->rx_ticks = 25; - bp->stats_ticks = 1000000 & 0xffff00; - bp->timer_interval = (CHIP_REV_IS_SLOW(bp) ? 5*HZ : HZ); bp->current_interval = (poll ? poll : bp->timer_interval); @@ -8137,7 +8168,6 @@ static int bnx2x_get_coalesce(struct net_device *dev, coal->rx_coalesce_usecs = bp->rx_ticks; coal->tx_coalesce_usecs = bp->tx_ticks; - coal->stats_block_coalesce_usecs = bp->stats_ticks; return 0; } @@ -8155,11 +8185,6 @@ static int bnx2x_set_coalesce(struct net_device *dev, if (bp->tx_ticks > 0x3000) bp->tx_ticks = 0x3000; - bp->stats_ticks = coal->stats_block_coalesce_usecs; - if (bp->stats_ticks > 0xffff00) - bp->stats_ticks = 0xffff00; - bp->stats_ticks &= 0xffff00; - if (netif_running(dev)) bnx2x_update_coalesce(bp); @@ -8836,76 +8861,99 @@ static const struct { long offset; int size; u32 flags; - char string[ETH_GSTRING_LEN]; +#define STATS_FLAGS_PORT 1 +#define STATS_FLAGS_FUNC 2 + u8 string[ETH_GSTRING_LEN]; } bnx2x_stats_arr[BNX2X_NUM_STATS] = { -/* 1 */ { STATS_OFFSET32(valid_bytes_received_hi), 8, 1, "rx_bytes" }, - { STATS_OFFSET32(error_bytes_received_hi), 8, 1, "rx_error_bytes" }, - { STATS_OFFSET32(total_bytes_transmitted_hi), 8, 1, "tx_bytes" }, - { STATS_OFFSET32(tx_stat_ifhcoutbadoctets_hi), 8, 0, "tx_error_bytes" }, +/* 1 */ { STATS_OFFSET32(valid_bytes_received_hi), + 8, STATS_FLAGS_FUNC, "rx_bytes" }, + { STATS_OFFSET32(error_bytes_received_hi), + 8, STATS_FLAGS_FUNC, "rx_error_bytes" }, + { STATS_OFFSET32(total_bytes_transmitted_hi), + 8, STATS_FLAGS_FUNC, "tx_bytes" }, + { STATS_OFFSET32(tx_stat_ifhcoutbadoctets_hi), + 8, STATS_FLAGS_PORT, "tx_error_bytes" }, { STATS_OFFSET32(total_unicast_packets_received_hi), - 8, 1, "rx_ucast_packets" }, + 8, STATS_FLAGS_FUNC, "rx_ucast_packets" }, { STATS_OFFSET32(total_multicast_packets_received_hi), - 8, 1, "rx_mcast_packets" }, + 8, STATS_FLAGS_FUNC, "rx_mcast_packets" }, { STATS_OFFSET32(total_broadcast_packets_received_hi), - 8, 1, "rx_bcast_packets" }, + 8, STATS_FLAGS_FUNC, "rx_bcast_packets" }, { STATS_OFFSET32(total_unicast_packets_transmitted_hi), - 8, 1, "tx_packets" }, + 8, STATS_FLAGS_FUNC, "tx_packets" }, { STATS_OFFSET32(tx_stat_dot3statsinternalmactransmiterrors_hi), - 8, 0, "tx_mac_errors" }, + 8, STATS_FLAGS_PORT, "tx_mac_errors" }, /* 10 */{ STATS_OFFSET32(rx_stat_dot3statscarriersenseerrors_hi), - 8, 0, "tx_carrier_errors" }, + 8, STATS_FLAGS_PORT, "tx_carrier_errors" }, { STATS_OFFSET32(rx_stat_dot3statsfcserrors_hi), - 8, 0, "rx_crc_errors" }, + 8, STATS_FLAGS_PORT, "rx_crc_errors" }, { STATS_OFFSET32(rx_stat_dot3statsalignmenterrors_hi), - 8, 0, "rx_align_errors" }, + 8, STATS_FLAGS_PORT, "rx_align_errors" }, { STATS_OFFSET32(tx_stat_dot3statssinglecollisionframes_hi), - 8, 0, "tx_single_collisions" }, + 8, STATS_FLAGS_PORT, "tx_single_collisions" }, { STATS_OFFSET32(tx_stat_dot3statsmultiplecollisionframes_hi), - 8, 0, "tx_multi_collisions" }, + 8, STATS_FLAGS_PORT, "tx_multi_collisions" }, { STATS_OFFSET32(tx_stat_dot3statsdeferredtransmissions_hi), - 8, 0, "tx_deferred" }, + 8, STATS_FLAGS_PORT, "tx_deferred" }, { STATS_OFFSET32(tx_stat_dot3statsexcessivecollisions_hi), - 8, 0, "tx_excess_collisions" }, + 8, STATS_FLAGS_PORT, "tx_excess_collisions" }, { STATS_OFFSET32(tx_stat_dot3statslatecollisions_hi), - 8, 0, "tx_late_collisions" }, + 8, STATS_FLAGS_PORT, "tx_late_collisions" }, { STATS_OFFSET32(tx_stat_etherstatscollisions_hi), - 8, 0, "tx_total_collisions" }, + 8, STATS_FLAGS_PORT, "tx_total_collisions" }, { STATS_OFFSET32(rx_stat_etherstatsfragments_hi), - 8, 0, "rx_fragments" }, -/* 20 */{ STATS_OFFSET32(rx_stat_etherstatsjabbers_hi), 8, 0, "rx_jabbers" }, + 8, STATS_FLAGS_PORT, "rx_fragments" }, +/* 20 */{ STATS_OFFSET32(rx_stat_etherstatsjabbers_hi), + 8, STATS_FLAGS_PORT, "rx_jabbers" }, { STATS_OFFSET32(rx_stat_etherstatsundersizepkts_hi), - 8, 0, "rx_undersize_packets" }, + 8, STATS_FLAGS_PORT, "rx_undersize_packets" }, { STATS_OFFSET32(jabber_packets_received), - 4, 1, "rx_oversize_packets" }, + 4, STATS_FLAGS_FUNC, "rx_oversize_packets" }, { STATS_OFFSET32(tx_stat_etherstatspkts64octets_hi), - 8, 0, "tx_64_byte_packets" }, + 8, STATS_FLAGS_PORT, "tx_64_byte_packets" }, { STATS_OFFSET32(tx_stat_etherstatspkts65octetsto127octets_hi), - 8, 0, "tx_65_to_127_byte_packets" }, + 8, STATS_FLAGS_PORT, "tx_65_to_127_byte_packets" }, { STATS_OFFSET32(tx_stat_etherstatspkts128octetsto255octets_hi), - 8, 0, "tx_128_to_255_byte_packets" }, + 8, STATS_FLAGS_PORT, "tx_128_to_255_byte_packets" }, { STATS_OFFSET32(tx_stat_etherstatspkts256octetsto511octets_hi), - 8, 0, "tx_256_to_511_byte_packets" }, + 8, STATS_FLAGS_PORT, "tx_256_to_511_byte_packets" }, { STATS_OFFSET32(tx_stat_etherstatspkts512octetsto1023octets_hi), - 8, 0, "tx_512_to_1023_byte_packets" }, + 8, STATS_FLAGS_PORT, "tx_512_to_1023_byte_packets" }, { STATS_OFFSET32(etherstatspkts1024octetsto1522octets_hi), - 8, 0, "tx_1024_to_1522_byte_packets" }, + 8, STATS_FLAGS_PORT, "tx_1024_to_1522_byte_packets" }, { STATS_OFFSET32(etherstatspktsover1522octets_hi), - 8, 0, "tx_1523_to_9022_byte_packets" }, + 8, STATS_FLAGS_PORT, "tx_1523_to_9022_byte_packets" }, /* 30 */{ STATS_OFFSET32(rx_stat_xonpauseframesreceived_hi), - 8, 0, "rx_xon_frames" }, + 8, STATS_FLAGS_PORT, "rx_xon_frames" }, { STATS_OFFSET32(rx_stat_xoffpauseframesreceived_hi), - 8, 0, "rx_xoff_frames" }, - { STATS_OFFSET32(tx_stat_outxonsent_hi), 8, 0, "tx_xon_frames" }, - { STATS_OFFSET32(tx_stat_outxoffsent_hi), 8, 0, "tx_xoff_frames" }, + 8, STATS_FLAGS_PORT, "rx_xoff_frames" }, + { STATS_OFFSET32(tx_stat_outxonsent_hi), + 8, STATS_FLAGS_PORT, "tx_xon_frames" }, + { STATS_OFFSET32(tx_stat_outxoffsent_hi), + 8, STATS_FLAGS_PORT, "tx_xoff_frames" }, { STATS_OFFSET32(rx_stat_maccontrolframesreceived_hi), - 8, 0, "rx_mac_ctrl_frames" }, - { STATS_OFFSET32(mac_filter_discard), 4, 1, "rx_filtered_packets" }, - { STATS_OFFSET32(no_buff_discard), 4, 1, "rx_discards" }, - { STATS_OFFSET32(xxoverflow_discard), 4, 1, "rx_fw_discards" }, - { STATS_OFFSET32(brb_drop_hi), 8, 1, "brb_discard" }, -/* 39 */{ STATS_OFFSET32(brb_truncate_discard), 8, 1, "brb_truncate" } + 8, STATS_FLAGS_PORT, "rx_mac_ctrl_frames" }, + { STATS_OFFSET32(mac_filter_discard), + 4, STATS_FLAGS_PORT, "rx_filtered_packets" }, + { STATS_OFFSET32(no_buff_discard), + 4, STATS_FLAGS_FUNC, "rx_discards" }, + { STATS_OFFSET32(xxoverflow_discard), + 4, STATS_FLAGS_PORT, "rx_fw_discards" }, + { STATS_OFFSET32(brb_drop_hi), + 8, STATS_FLAGS_PORT, "brb_discard" }, + { STATS_OFFSET32(brb_truncate_hi), + 8, STATS_FLAGS_PORT, "brb_truncate" }, +/* 40 */{ STATS_OFFSET32(rx_err_discard_pkt), + 4, STATS_FLAGS_FUNC, "rx_phy_ip_err_discards"}, + { STATS_OFFSET32(rx_skb_alloc_failed), + 4, STATS_FLAGS_FUNC, "rx_skb_alloc_discard" }, +/* 42 */{ STATS_OFFSET32(hw_csum_err), + 4, STATS_FLAGS_FUNC, "rx_csum_offload_errors" } }; +#define IS_NOT_E1HMF_STAT(bp, i) \ + (IS_E1HMF(bp) && (bnx2x_stats_arr[i].flags & STATS_FLAGS_PORT)) + static void bnx2x_get_strings(struct net_device *dev, u32 stringset, u8 *buf) { struct bnx2x *bp = netdev_priv(dev); @@ -8914,7 +8962,7 @@ static void bnx2x_get_strings(struct net_device *dev, u32 stringset, u8 *buf) switch (stringset) { case ETH_SS_STATS: for (i = 0, j = 0; i < BNX2X_NUM_STATS; i++) { - if (IS_E1HMF(bp) && (!bnx2x_stats_arr[i].flags)) + if (IS_NOT_E1HMF_STAT(bp, i)) continue; strcpy(buf + j*ETH_GSTRING_LEN, bnx2x_stats_arr[i].string); @@ -8934,7 +8982,7 @@ static int bnx2x_get_stats_count(struct net_device *dev) int i, num_stats = 0; for (i = 0; i < BNX2X_NUM_STATS; i++) { - if (IS_E1HMF(bp) && (!bnx2x_stats_arr[i].flags)) + if (IS_NOT_E1HMF_STAT(bp, i)) continue; num_stats++; } @@ -8949,7 +8997,7 @@ static void bnx2x_get_ethtool_stats(struct net_device *dev, int i, j; for (i = 0, j = 0; i < BNX2X_NUM_STATS; i++) { - if (IS_E1HMF(bp) && (!bnx2x_stats_arr[i].flags)) + if (IS_NOT_E1HMF_STAT(bp, i)) continue; if (bnx2x_stats_arr[i].size == 0) { diff --git a/drivers/net/bnx2x_reg.h b/drivers/net/bnx2x_reg.h index 15c9a994672..40c3a7735d2 100644 --- a/drivers/net/bnx2x_reg.h +++ b/drivers/net/bnx2x_reg.h @@ -1727,6 +1727,9 @@ /* [R 32] Rx statistics : In user packets discarded due to BRB backpressure for port0 */ #define NIG_REG_STAT0_BRB_DISCARD 0x105f0 +/* [R 32] Rx statistics : In user packets truncated due to BRB backpressure + for port0 */ +#define NIG_REG_STAT0_BRB_TRUNCATE 0x105f8 /* [WB_R 36] Tx statistics : Number of packets from emac0 or bmac0 that between 1024 and 1522 bytes for port0 */ #define NIG_REG_STAT0_EGRESS_MAC_PKT0 0x10750 -- GitLab From 471de716b782fb55ae0fdc040cf2722caffeeb94 Mon Sep 17 00:00:00 2001 From: Eilon Greenstein Date: Wed, 13 Aug 2008 15:49:35 -0700 Subject: [PATCH 247/750] bnx2x: FW Internal Memory structure FW Internal Memory structure The FW uses data structures on the chip internal memory to aggregate the connections when TPA is enabled. The driver was clearing the wrong offsets and therefore one function could cause another function to loose packets. Changing the initialization of the chip internal memory to clear only the relevant memory for each function which is being loaded Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x_init_values.h | 533 +++++++++++++++----------------- drivers/net/bnx2x_main.c | 100 +++--- 2 files changed, 299 insertions(+), 334 deletions(-) diff --git a/drivers/net/bnx2x_init_values.h b/drivers/net/bnx2x_init_values.h index 63019055e4b..9755bf6b08d 100644 --- a/drivers/net/bnx2x_init_values.h +++ b/drivers/net/bnx2x_init_values.h @@ -901,31 +901,28 @@ static const struct raw_op init_ops[] = { {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3760, 0x4}, {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x1e20, 0x42}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3738, 0x9}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3000, 0x400}, + {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x4b68, 0x2}, {OP_SW_E1H, USEM_REG_FAST_MEMORY + 0x3738 + 0x24, 0x10293}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x2c00, 0x2}, + {OP_SW_E1, USEM_REG_FAST_MEMORY + 0x4b68 + 0x8, 0x20278}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3180, 0x42}, - {OP_SW_E1, USEM_REG_FAST_MEMORY + 0x2c00 + 0x8, 0x20278}, + {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x4b10, 0x2}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5000, 0x400}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x4b68, 0x2}, + {OP_SW_E1, USEM_REG_FAST_MEMORY + 0x2830, 0x2027a}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x4000, 0x2}, - {OP_SW_E1, USEM_REG_FAST_MEMORY + 0x4b68 + 0x8, 0x2027a}, {OP_SW_E1H, USEM_REG_FAST_MEMORY + 0x4000 + 0x8, 0x20294}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x4b10, 0x2}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x6b68, 0x2}, - {OP_SW_E1, USEM_REG_FAST_MEMORY + 0x2830, 0x2027c}, {OP_SW_E1H, USEM_REG_FAST_MEMORY + 0x6b68 + 0x8, 0x20296}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x6b10, 0x2}, {OP_SW_E1H, USEM_REG_FAST_MEMORY + 0x74c0, 0x20298}, {OP_WR, USEM_REG_FAST_MEMORY + 0x10800, 0x1000000}, - {OP_SW_E1, USEM_REG_FAST_MEMORY + 0x10c00, 0x10027e}, + {OP_SW_E1, USEM_REG_FAST_MEMORY + 0x10c00, 0x10027c}, {OP_SW_E1H, USEM_REG_FAST_MEMORY + 0x10c00, 0x10029a}, {OP_WR, USEM_REG_FAST_MEMORY + 0x10800, 0x0}, - {OP_SW_E1, USEM_REG_FAST_MEMORY + 0x10c40, 0x10028e}, + {OP_SW_E1, USEM_REG_FAST_MEMORY + 0x10c40, 0x10028c}, {OP_SW_E1H, USEM_REG_FAST_MEMORY + 0x10c40, 0x1002aa}, {OP_ZP_E1, USEM_REG_INT_TABLE, 0xc20000}, {OP_ZP_E1H, USEM_REG_INT_TABLE, 0xc40000}, - {OP_WR_64_E1, USEM_REG_INT_TABLE + 0x368, 0x13029e}, + {OP_WR_64_E1, USEM_REG_INT_TABLE + 0x368, 0x13029c}, {OP_WR_64_E1H, USEM_REG_INT_TABLE + 0x368, 0x1302ba}, {OP_ZP_E1, USEM_REG_PRAM, 0x311c0000}, {OP_ZP_E1H, USEM_REG_PRAM, 0x31070000}, @@ -933,11 +930,11 @@ static const struct raw_op init_ops[] = { {OP_ZP_E1H, USEM_REG_PRAM + 0x8000, 0x330e0c42}, {OP_ZP_E1, USEM_REG_PRAM + 0x10000, 0x38561919}, {OP_ZP_E1H, USEM_REG_PRAM + 0x10000, 0x389b1906}, - {OP_WR_64_E1, USEM_REG_PRAM + 0x17fe0, 0x500402a0}, + {OP_WR_64_E1, USEM_REG_PRAM + 0x17fe0, 0x5004029e}, {OP_ZP_E1H, USEM_REG_PRAM + 0x18000, 0x132272d}, {OP_WR_64_E1H, USEM_REG_PRAM + 0x18250, 0x4fb602bc}, -#define USEM_COMMON_END 790 -#define USEM_PORT0_START 790 +#define USEM_COMMON_END 787 +#define USEM_PORT0_START 787 {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x1400, 0xa0}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x9000, 0xa0}, {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x1900, 0xa}, @@ -950,44 +947,27 @@ static const struct raw_op init_ops[] = { {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3288, 0x96}, {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x5440, 0x72}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5000, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3000, 0x20}, + {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x4b78, 0x52}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5100, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3100, 0x20}, + {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x4e08, 0xc}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5200, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3200, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5300, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3300, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5400, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3400, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5500, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3500, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5600, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3600, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5700, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3700, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5800, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3800, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5900, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3900, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5a00, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3a00, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5b00, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3b00, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5c00, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3c00, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5d00, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3d00, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5e00, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3e00, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5f00, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3f00, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x6b78, 0x52}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x2c10, 0x2}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x6e08, 0xc}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x4b78, 0x52}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x4e08, 0xc}, -#define USEM_PORT0_END 838 -#define USEM_PORT1_START 838 +#define USEM_PORT0_END 818 +#define USEM_PORT1_START 818 {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x1680, 0xa0}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x9280, 0xa0}, {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x1928, 0xa}, @@ -1000,76 +980,59 @@ static const struct raw_op init_ops[] = { {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x34e0, 0x96}, {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x5608, 0x72}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5080, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3080, 0x20}, + {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x4cc0, 0x52}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5180, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3180, 0x20}, + {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x4e38, 0xc}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5280, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3280, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5380, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3380, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5480, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3480, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5580, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3580, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5680, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3680, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5780, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3780, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5880, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3880, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5980, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3980, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5a80, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3a80, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5b80, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3b80, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5c80, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3c80, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5d80, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3d80, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5e80, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3e80, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5f80, 0x20}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3f80, 0x20}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x6cc0, 0x52}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x2c20, 0x2}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x6e38, 0xc}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x4cc0, 0x52}, - {OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x4e38, 0xc}, -#define USEM_PORT1_END 886 -#define USEM_FUNC0_START 886 +#define USEM_PORT1_END 849 +#define USEM_FUNC0_START 849 {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3000, 0x4}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x4010, 0x2}, -#define USEM_FUNC0_END 888 -#define USEM_FUNC1_START 888 +#define USEM_FUNC0_END 851 +#define USEM_FUNC1_START 851 {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3010, 0x4}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x4020, 0x2}, -#define USEM_FUNC1_END 890 -#define USEM_FUNC2_START 890 +#define USEM_FUNC1_END 853 +#define USEM_FUNC2_START 853 {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3020, 0x4}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x4030, 0x2}, -#define USEM_FUNC2_END 892 -#define USEM_FUNC3_START 892 +#define USEM_FUNC2_END 855 +#define USEM_FUNC3_START 855 {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3030, 0x4}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x4040, 0x2}, -#define USEM_FUNC3_END 894 -#define USEM_FUNC4_START 894 +#define USEM_FUNC3_END 857 +#define USEM_FUNC4_START 857 {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3040, 0x4}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x4050, 0x2}, -#define USEM_FUNC4_END 896 -#define USEM_FUNC5_START 896 +#define USEM_FUNC4_END 859 +#define USEM_FUNC5_START 859 {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3050, 0x4}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x4060, 0x2}, -#define USEM_FUNC5_END 898 -#define USEM_FUNC6_START 898 +#define USEM_FUNC5_END 861 +#define USEM_FUNC6_START 861 {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3060, 0x4}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x4070, 0x2}, -#define USEM_FUNC6_END 900 -#define USEM_FUNC7_START 900 +#define USEM_FUNC6_END 863 +#define USEM_FUNC7_START 863 {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3070, 0x4}, {OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x4080, 0x2}, -#define USEM_FUNC7_END 902 -#define CSEM_COMMON_START 902 +#define USEM_FUNC7_END 865 +#define CSEM_COMMON_START 865 {OP_RD, CSEM_REG_MSG_NUM_FIC0, 0x0}, {OP_RD, CSEM_REG_MSG_NUM_FIC1, 0x0}, {OP_RD, CSEM_REG_MSG_NUM_FOC0, 0x0}, @@ -1128,29 +1091,29 @@ static const struct raw_op init_ops[] = { {OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x11e8, 0x0}, {OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x25c0, 0x240}, {OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x3000, 0xc0}, - {OP_SW_E1, CSEM_REG_FAST_MEMORY + 0x2ec8, 0x802a2}, + {OP_SW_E1, CSEM_REG_FAST_MEMORY + 0x2ec8, 0x802a0}, {OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x4070, 0x80}, {OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x5280, 0x4}, {OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x6280, 0x240}, {OP_SW_E1H, CSEM_REG_FAST_MEMORY + 0x6b88, 0x2002be}, {OP_WR, CSEM_REG_FAST_MEMORY + 0x10800, 0x13fffff}, - {OP_SW_E1, CSEM_REG_FAST_MEMORY + 0x10c00, 0x1002aa}, + {OP_SW_E1, CSEM_REG_FAST_MEMORY + 0x10c00, 0x1002a8}, {OP_SW_E1H, CSEM_REG_FAST_MEMORY + 0x10c00, 0x1002de}, {OP_WR, CSEM_REG_FAST_MEMORY + 0x10800, 0x0}, - {OP_SW_E1, CSEM_REG_FAST_MEMORY + 0x10c40, 0x1002ba}, + {OP_SW_E1, CSEM_REG_FAST_MEMORY + 0x10c40, 0x1002b8}, {OP_SW_E1H, CSEM_REG_FAST_MEMORY + 0x10c40, 0x1002ee}, {OP_ZP_E1, CSEM_REG_INT_TABLE, 0x6e0000}, {OP_ZP_E1H, CSEM_REG_INT_TABLE, 0x6f0000}, - {OP_WR_64_E1, CSEM_REG_INT_TABLE + 0x380, 0x1002ca}, + {OP_WR_64_E1, CSEM_REG_INT_TABLE + 0x380, 0x1002c8}, {OP_WR_64_E1H, CSEM_REG_INT_TABLE + 0x380, 0x1002fe}, {OP_ZP_E1, CSEM_REG_PRAM, 0x32580000}, {OP_ZP_E1H, CSEM_REG_PRAM, 0x31fa0000}, {OP_ZP_E1, CSEM_REG_PRAM + 0x8000, 0x18270c96}, {OP_ZP_E1H, CSEM_REG_PRAM + 0x8000, 0x19040c7f}, - {OP_WR_64_E1, CSEM_REG_PRAM + 0xb210, 0x682402cc}, + {OP_WR_64_E1, CSEM_REG_PRAM + 0xb210, 0x682402ca}, {OP_WR_64_E1H, CSEM_REG_PRAM + 0xb430, 0x67e00300}, -#define CSEM_COMMON_END 981 -#define CSEM_PORT0_START 981 +#define CSEM_COMMON_END 944 +#define CSEM_PORT0_START 944 {OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x1400, 0xa0}, {OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x8000, 0xa0}, {OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x1900, 0x10}, @@ -1163,8 +1126,8 @@ static const struct raw_op init_ops[] = { {OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x6040, 0x30}, {OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x3040, 0x6}, {OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x2410, 0x30}, -#define CSEM_PORT0_END 993 -#define CSEM_PORT1_START 993 +#define CSEM_PORT0_END 956 +#define CSEM_PORT1_START 956 {OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x1680, 0xa0}, {OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x8280, 0xa0}, {OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x1940, 0x10}, @@ -1177,43 +1140,43 @@ static const struct raw_op init_ops[] = { {OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x6100, 0x30}, {OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x3058, 0x6}, {OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x24d0, 0x30}, -#define CSEM_PORT1_END 1005 -#define CSEM_FUNC0_START 1005 +#define CSEM_PORT1_END 968 +#define CSEM_FUNC0_START 968 {OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x1148, 0x0}, {OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x3300, 0x2}, -#define CSEM_FUNC0_END 1007 -#define CSEM_FUNC1_START 1007 +#define CSEM_FUNC0_END 970 +#define CSEM_FUNC1_START 970 {OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x114c, 0x0}, {OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x3308, 0x2}, -#define CSEM_FUNC1_END 1009 -#define CSEM_FUNC2_START 1009 +#define CSEM_FUNC1_END 972 +#define CSEM_FUNC2_START 972 {OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x1150, 0x0}, {OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x3310, 0x2}, -#define CSEM_FUNC2_END 1011 -#define CSEM_FUNC3_START 1011 +#define CSEM_FUNC2_END 974 +#define CSEM_FUNC3_START 974 {OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x1154, 0x0}, {OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x3318, 0x2}, -#define CSEM_FUNC3_END 1013 -#define CSEM_FUNC4_START 1013 +#define CSEM_FUNC3_END 976 +#define CSEM_FUNC4_START 976 {OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x1158, 0x0}, {OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x3320, 0x2}, -#define CSEM_FUNC4_END 1015 -#define CSEM_FUNC5_START 1015 +#define CSEM_FUNC4_END 978 +#define CSEM_FUNC5_START 978 {OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x115c, 0x0}, {OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x3328, 0x2}, -#define CSEM_FUNC5_END 1017 -#define CSEM_FUNC6_START 1017 +#define CSEM_FUNC5_END 980 +#define CSEM_FUNC6_START 980 {OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x1160, 0x0}, {OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x3330, 0x2}, -#define CSEM_FUNC6_END 1019 -#define CSEM_FUNC7_START 1019 +#define CSEM_FUNC6_END 982 +#define CSEM_FUNC7_START 982 {OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x1164, 0x0}, {OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x3338, 0x2}, -#define CSEM_FUNC7_END 1021 -#define XPB_COMMON_START 1021 +#define CSEM_FUNC7_END 984 +#define XPB_COMMON_START 984 {OP_WR, GRCBASE_XPB + PB_REG_CONTROL, 0x20}, -#define XPB_COMMON_END 1022 -#define DQ_COMMON_START 1022 +#define XPB_COMMON_END 985 +#define DQ_COMMON_START 985 {OP_WR, DORQ_REG_MODE_ACT, 0x2}, {OP_WR, DORQ_REG_NORM_CID_OFST, 0x3}, {OP_WR, DORQ_REG_OUTST_REQ, 0x4}, @@ -1232,8 +1195,8 @@ static const struct raw_op init_ops[] = { {OP_WR, DORQ_REG_DQ_FIFO_AFULL_TH, 0x76c}, {OP_WR, DORQ_REG_REGN, 0x7c1004}, {OP_WR, DORQ_REG_IF_EN, 0xf}, -#define DQ_COMMON_END 1040 -#define TIMERS_COMMON_START 1040 +#define DQ_COMMON_END 1003 +#define TIMERS_COMMON_START 1003 {OP_ZR, TM_REG_CLIN_PRIOR0_CLIENT, 0x2}, {OP_WR, TM_REG_LIN_SETCLR_FIFO_ALFULL_THR, 0x1c}, {OP_WR, TM_REG_CFC_AC_CRDCNT_VAL, 0x1}, @@ -1256,14 +1219,14 @@ static const struct raw_op init_ops[] = { {OP_WR, TM_REG_EN_CL0_INPUT, 0x1}, {OP_WR, TM_REG_EN_CL1_INPUT, 0x1}, {OP_WR, TM_REG_EN_CL2_INPUT, 0x1}, -#define TIMERS_COMMON_END 1062 -#define TIMERS_PORT0_START 1062 +#define TIMERS_COMMON_END 1025 +#define TIMERS_PORT0_START 1025 {OP_ZR, TM_REG_LIN0_PHY_ADDR, 0x2}, -#define TIMERS_PORT0_END 1063 -#define TIMERS_PORT1_START 1063 +#define TIMERS_PORT0_END 1026 +#define TIMERS_PORT1_START 1026 {OP_ZR, TM_REG_LIN1_PHY_ADDR, 0x2}, -#define TIMERS_PORT1_END 1064 -#define XSDM_COMMON_START 1064 +#define TIMERS_PORT1_END 1027 +#define XSDM_COMMON_START 1027 {OP_WR_E1, XSDM_REG_CFC_RSP_START_ADDR, 0x614}, {OP_WR_E1H, XSDM_REG_CFC_RSP_START_ADDR, 0x424}, {OP_WR_E1, XSDM_REG_CMP_COUNTER_START_ADDR, 0x600}, @@ -1311,8 +1274,8 @@ static const struct raw_op init_ops[] = { {OP_WR_ASIC, XSDM_REG_TIMER_TICK, 0x3e8}, {OP_WR_EMUL, XSDM_REG_TIMER_TICK, 0x1}, {OP_WR_FPGA, XSDM_REG_TIMER_TICK, 0xa}, -#define XSDM_COMMON_END 1111 -#define QM_COMMON_START 1111 +#define XSDM_COMMON_END 1074 +#define QM_COMMON_START 1074 {OP_WR, QM_REG_ACTCTRINITVAL_0, 0x6}, {OP_WR, QM_REG_ACTCTRINITVAL_1, 0x5}, {OP_WR, QM_REG_ACTCTRINITVAL_2, 0xa}, @@ -1613,8 +1576,8 @@ static const struct raw_op init_ops[] = { {OP_WR_E1H, QM_REG_PQ2PCIFUNC_6, 0x5}, {OP_WR_E1H, QM_REG_PQ2PCIFUNC_7, 0x7}, {OP_WR, QM_REG_CMINTEN, 0xff}, -#define QM_COMMON_END 1411 -#define PBF_COMMON_START 1411 +#define QM_COMMON_END 1374 +#define PBF_COMMON_START 1374 {OP_WR, PBF_REG_INIT, 0x1}, {OP_WR, PBF_REG_INIT_P4, 0x1}, {OP_WR, PBF_REG_MAC_LB_ENABLE, 0x1}, @@ -1622,20 +1585,20 @@ static const struct raw_op init_ops[] = { {OP_WR, PBF_REG_INIT_P4, 0x0}, {OP_WR, PBF_REG_INIT, 0x0}, {OP_WR, PBF_REG_DISABLE_NEW_TASK_PROC_P4, 0x0}, -#define PBF_COMMON_END 1418 -#define PBF_PORT0_START 1418 +#define PBF_COMMON_END 1381 +#define PBF_PORT0_START 1381 {OP_WR, PBF_REG_INIT_P0, 0x1}, {OP_WR, PBF_REG_MAC_IF0_ENABLE, 0x1}, {OP_WR, PBF_REG_INIT_P0, 0x0}, {OP_WR, PBF_REG_DISABLE_NEW_TASK_PROC_P0, 0x0}, -#define PBF_PORT0_END 1422 -#define PBF_PORT1_START 1422 +#define PBF_PORT0_END 1385 +#define PBF_PORT1_START 1385 {OP_WR, PBF_REG_INIT_P1, 0x1}, {OP_WR, PBF_REG_MAC_IF1_ENABLE, 0x1}, {OP_WR, PBF_REG_INIT_P1, 0x0}, {OP_WR, PBF_REG_DISABLE_NEW_TASK_PROC_P1, 0x0}, -#define PBF_PORT1_END 1426 -#define XCM_COMMON_START 1426 +#define PBF_PORT1_END 1389 +#define XCM_COMMON_START 1389 {OP_WR, XCM_REG_XX_OVFL_EVNT_ID, 0x32}, {OP_WR, XCM_REG_XQM_XCM_HDR_P, 0x3150020}, {OP_WR, XCM_REG_XQM_XCM_HDR_S, 0x3150020}, @@ -1670,7 +1633,7 @@ static const struct raw_op init_ops[] = { {OP_WR_E1, XCM_REG_XX_MSG_NUM, 0x1f}, {OP_WR_E1H, XCM_REG_XX_MSG_NUM, 0x20}, {OP_ZR, XCM_REG_XX_TABLE, 0x12}, - {OP_SW_E1, XCM_REG_XX_DESCR_TABLE, 0x1f02ce}, + {OP_SW_E1, XCM_REG_XX_DESCR_TABLE, 0x1f02cc}, {OP_SW_E1H, XCM_REG_XX_DESCR_TABLE, 0x1f0302}, {OP_WR, XCM_REG_N_SM_CTX_LD_0, 0xf}, {OP_WR, XCM_REG_N_SM_CTX_LD_1, 0x7}, @@ -1700,8 +1663,8 @@ static const struct raw_op init_ops[] = { {OP_WR, XCM_REG_CDU_SM_WR_IFEN, 0x1}, {OP_WR, XCM_REG_CDU_SM_RD_IFEN, 0x1}, {OP_WR, XCM_REG_XCM_CFC_IFEN, 0x1}, -#define XCM_COMMON_END 1490 -#define XCM_PORT0_START 1490 +#define XCM_COMMON_END 1453 +#define XCM_PORT0_START 1453 {OP_WR_E1, XCM_REG_GLB_DEL_ACK_TMR_VAL_0, 0xc8}, {OP_WR_E1, XCM_REG_GLB_DEL_ACK_MAX_CNT_0, 0x2}, {OP_WR_E1, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD00, 0x0}, @@ -1710,8 +1673,8 @@ static const struct raw_op init_ops[] = { {OP_WR_E1, XCM_REG_WU_DA_CNT_CMD10, 0x2}, {OP_WR_E1, XCM_REG_WU_DA_CNT_UPD_VAL00, 0xff}, {OP_WR_E1, XCM_REG_WU_DA_CNT_UPD_VAL10, 0xff}, -#define XCM_PORT0_END 1498 -#define XCM_PORT1_START 1498 +#define XCM_PORT0_END 1461 +#define XCM_PORT1_START 1461 {OP_WR_E1, XCM_REG_GLB_DEL_ACK_TMR_VAL_1, 0xc8}, {OP_WR_E1, XCM_REG_GLB_DEL_ACK_MAX_CNT_1, 0x2}, {OP_WR_E1, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD01, 0x0}, @@ -1720,8 +1683,8 @@ static const struct raw_op init_ops[] = { {OP_WR_E1, XCM_REG_WU_DA_CNT_CMD11, 0x2}, {OP_WR_E1, XCM_REG_WU_DA_CNT_UPD_VAL01, 0xff}, {OP_WR_E1, XCM_REG_WU_DA_CNT_UPD_VAL11, 0xff}, -#define XCM_PORT1_END 1506 -#define XCM_FUNC0_START 1506 +#define XCM_PORT1_END 1469 +#define XCM_FUNC0_START 1469 {OP_WR_E1H, XCM_REG_GLB_DEL_ACK_TMR_VAL_0, 0xc8}, {OP_WR_E1H, XCM_REG_GLB_DEL_ACK_MAX_CNT_0, 0x2}, {OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD00, 0x0}, @@ -1731,8 +1694,8 @@ static const struct raw_op init_ops[] = { {OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL00, 0xff}, {OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL10, 0xff}, {OP_WR_E1H, XCM_REG_PHYS_QNUM3_0, 0x0}, -#define XCM_FUNC0_END 1515 -#define XCM_FUNC1_START 1515 +#define XCM_FUNC0_END 1478 +#define XCM_FUNC1_START 1478 {OP_WR_E1H, XCM_REG_GLB_DEL_ACK_TMR_VAL_1, 0xc8}, {OP_WR_E1H, XCM_REG_GLB_DEL_ACK_MAX_CNT_1, 0x2}, {OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD01, 0x0}, @@ -1742,8 +1705,8 @@ static const struct raw_op init_ops[] = { {OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL01, 0xff}, {OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL11, 0xff}, {OP_WR_E1H, XCM_REG_PHYS_QNUM3_1, 0x0}, -#define XCM_FUNC1_END 1524 -#define XCM_FUNC2_START 1524 +#define XCM_FUNC1_END 1487 +#define XCM_FUNC2_START 1487 {OP_WR_E1H, XCM_REG_GLB_DEL_ACK_TMR_VAL_0, 0xc8}, {OP_WR_E1H, XCM_REG_GLB_DEL_ACK_MAX_CNT_0, 0x2}, {OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD00, 0x0}, @@ -1753,8 +1716,8 @@ static const struct raw_op init_ops[] = { {OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL00, 0xff}, {OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL10, 0xff}, {OP_WR_E1H, XCM_REG_PHYS_QNUM3_0, 0x0}, -#define XCM_FUNC2_END 1533 -#define XCM_FUNC3_START 1533 +#define XCM_FUNC2_END 1496 +#define XCM_FUNC3_START 1496 {OP_WR_E1H, XCM_REG_GLB_DEL_ACK_TMR_VAL_1, 0xc8}, {OP_WR_E1H, XCM_REG_GLB_DEL_ACK_MAX_CNT_1, 0x2}, {OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD01, 0x0}, @@ -1764,8 +1727,8 @@ static const struct raw_op init_ops[] = { {OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL01, 0xff}, {OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL11, 0xff}, {OP_WR_E1H, XCM_REG_PHYS_QNUM3_1, 0x0}, -#define XCM_FUNC3_END 1542 -#define XCM_FUNC4_START 1542 +#define XCM_FUNC3_END 1505 +#define XCM_FUNC4_START 1505 {OP_WR_E1H, XCM_REG_GLB_DEL_ACK_TMR_VAL_0, 0xc8}, {OP_WR_E1H, XCM_REG_GLB_DEL_ACK_MAX_CNT_0, 0x2}, {OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD00, 0x0}, @@ -1775,8 +1738,8 @@ static const struct raw_op init_ops[] = { {OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL00, 0xff}, {OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL10, 0xff}, {OP_WR_E1H, XCM_REG_PHYS_QNUM3_0, 0x0}, -#define XCM_FUNC4_END 1551 -#define XCM_FUNC5_START 1551 +#define XCM_FUNC4_END 1514 +#define XCM_FUNC5_START 1514 {OP_WR_E1H, XCM_REG_GLB_DEL_ACK_TMR_VAL_1, 0xc8}, {OP_WR_E1H, XCM_REG_GLB_DEL_ACK_MAX_CNT_1, 0x2}, {OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD01, 0x0}, @@ -1786,8 +1749,8 @@ static const struct raw_op init_ops[] = { {OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL01, 0xff}, {OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL11, 0xff}, {OP_WR_E1H, XCM_REG_PHYS_QNUM3_1, 0x0}, -#define XCM_FUNC5_END 1560 -#define XCM_FUNC6_START 1560 +#define XCM_FUNC5_END 1523 +#define XCM_FUNC6_START 1523 {OP_WR_E1H, XCM_REG_GLB_DEL_ACK_TMR_VAL_0, 0xc8}, {OP_WR_E1H, XCM_REG_GLB_DEL_ACK_MAX_CNT_0, 0x2}, {OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD00, 0x0}, @@ -1797,8 +1760,8 @@ static const struct raw_op init_ops[] = { {OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL00, 0xff}, {OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL10, 0xff}, {OP_WR_E1H, XCM_REG_PHYS_QNUM3_0, 0x0}, -#define XCM_FUNC6_END 1569 -#define XCM_FUNC7_START 1569 +#define XCM_FUNC6_END 1532 +#define XCM_FUNC7_START 1532 {OP_WR_E1H, XCM_REG_GLB_DEL_ACK_TMR_VAL_1, 0xc8}, {OP_WR_E1H, XCM_REG_GLB_DEL_ACK_MAX_CNT_1, 0x2}, {OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD01, 0x0}, @@ -1808,8 +1771,8 @@ static const struct raw_op init_ops[] = { {OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL01, 0xff}, {OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL11, 0xff}, {OP_WR_E1H, XCM_REG_PHYS_QNUM3_1, 0x0}, -#define XCM_FUNC7_END 1578 -#define XSEM_COMMON_START 1578 +#define XCM_FUNC7_END 1541 +#define XSEM_COMMON_START 1541 {OP_RD, XSEM_REG_MSG_NUM_FIC0, 0x0}, {OP_RD, XSEM_REG_MSG_NUM_FIC1, 0x0}, {OP_RD, XSEM_REG_MSG_NUM_FOC0, 0x0}, @@ -1876,9 +1839,9 @@ static const struct raw_op init_ops[] = { {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x9000, 0x2}, {OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x3368, 0x0}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x21a8, 0x86}, - {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x3370, 0x202ed}, + {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x3370, 0x202eb}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x2000, 0x20}, - {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x3b90, 0x402ef}, + {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x3b90, 0x402ed}, {OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0x23c8, 0x0}, {OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x1518, 0x1}, {OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x23d0, 0x20321}, @@ -1886,29 +1849,29 @@ static const struct raw_op init_ops[] = { {OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x2498, 0x40323}, {OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x1838, 0x0}, {OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0x2ac8, 0x0}, - {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x1820, 0x202f3}, + {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x1820, 0x202f1}, {OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0x2ab8, 0x0}, {OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x4ac0, 0x2}, {OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0x3010, 0x1}, {OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x4b00, 0x4}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x4040, 0x10}, - {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x1f50, 0x202f5}, + {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x1f50, 0x202f3}, {OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x4000, 0x100327}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x6ac0, 0x2}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x6b00, 0x4}, {OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x83b0, 0x20337}, {OP_WR, XSEM_REG_FAST_MEMORY + 0x10800, 0x0}, - {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x10c00, 0x1002f7}, + {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x10c00, 0x1002f5}, {OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x10c00, 0x100339}, {OP_WR, XSEM_REG_FAST_MEMORY + 0x10800, 0x1000000}, - {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x10c40, 0x80307}, + {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x10c40, 0x80305}, {OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x10c40, 0x80349}, {OP_WR, XSEM_REG_FAST_MEMORY + 0x10800, 0x2000000}, - {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x10c60, 0x8030f}, + {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x10c60, 0x8030d}, {OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x10c60, 0x80351}, {OP_ZP_E1, XSEM_REG_INT_TABLE, 0xa90000}, {OP_ZP_E1H, XSEM_REG_INT_TABLE, 0xac0000}, - {OP_WR_64_E1, XSEM_REG_INT_TABLE + 0x368, 0x130317}, + {OP_WR_64_E1, XSEM_REG_INT_TABLE + 0x368, 0x130315}, {OP_WR_64_E1H, XSEM_REG_INT_TABLE + 0x368, 0x130359}, {OP_ZP_E1, XSEM_REG_PRAM, 0x344e0000}, {OP_ZP_E1H, XSEM_REG_PRAM, 0x34620000}, @@ -1918,10 +1881,10 @@ static const struct raw_op init_ops[] = { {OP_ZP_E1H, XSEM_REG_PRAM + 0x10000, 0x3e971b22}, {OP_ZP_E1, XSEM_REG_PRAM + 0x18000, 0x1dd02ad2}, {OP_ZP_E1H, XSEM_REG_PRAM + 0x18000, 0x21542ac8}, - {OP_WR_64_E1, XSEM_REG_PRAM + 0x1c0d0, 0x47e60319}, + {OP_WR_64_E1, XSEM_REG_PRAM + 0x1c0d0, 0x47e60317}, {OP_WR_64_E1H, XSEM_REG_PRAM + 0x1c8d0, 0x46e6035b}, -#define XSEM_COMMON_END 1688 -#define XSEM_PORT0_START 1688 +#define XSEM_COMMON_END 1651 +#define XSEM_PORT0_START 1651 {OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x3ba0, 0x10}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0xc000, 0xfc}, {OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x3c20, 0x1c}, @@ -1934,7 +1897,7 @@ static const struct raw_op init_ops[] = { {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x26e8, 0x1c}, {OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x3b58, 0x0}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x27c8, 0x1c}, - {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x3d10, 0x10031b}, + {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x3d10, 0x100319}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0xa000, 0x28}, {OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x1500, 0x0}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0xa140, 0xc}, @@ -1950,12 +1913,12 @@ static const struct raw_op init_ops[] = { {OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x6ac8, 0x2035d}, {OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x50b8, 0x1}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x6b10, 0x42}, - {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x4ac8, 0x2032b}, + {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x4ac8, 0x20329}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x6d20, 0x4}, {OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x4b10, 0x42}, {OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x4d20, 0x4}, -#define XSEM_PORT0_END 1720 -#define XSEM_PORT1_START 1720 +#define XSEM_PORT0_END 1683 +#define XSEM_PORT1_START 1683 {OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x3be0, 0x10}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0xc3f0, 0xfc}, {OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x3c90, 0x1c}, @@ -1968,7 +1931,7 @@ static const struct raw_op init_ops[] = { {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x2758, 0x1c}, {OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x3b5c, 0x0}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x2838, 0x1c}, - {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x3d50, 0x10032d}, + {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x3d50, 0x10032b}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0xa0a0, 0x28}, {OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x1504, 0x0}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0xa170, 0xc}, @@ -1984,65 +1947,65 @@ static const struct raw_op init_ops[] = { {OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x6ad0, 0x2035f}, {OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x50bc, 0x1}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x6c18, 0x42}, - {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x4ad0, 0x2033d}, + {OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x4ad0, 0x2033b}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x6d30, 0x4}, {OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x4c18, 0x42}, {OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x4d30, 0x4}, -#define XSEM_PORT1_END 1752 -#define XSEM_FUNC0_START 1752 +#define XSEM_PORT1_END 1715 +#define XSEM_FUNC0_START 1715 {OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0xc7e0, 0x0}, {OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x28b8, 0x100361}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x5048, 0xe}, -#define XSEM_FUNC0_END 1755 -#define XSEM_FUNC1_START 1755 +#define XSEM_FUNC0_END 1718 +#define XSEM_FUNC1_START 1718 {OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0xc7e4, 0x0}, {OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x28f8, 0x100371}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x5080, 0xe}, -#define XSEM_FUNC1_END 1758 -#define XSEM_FUNC2_START 1758 +#define XSEM_FUNC1_END 1721 +#define XSEM_FUNC2_START 1721 {OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0xc7e8, 0x0}, {OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x2938, 0x100381}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x50b8, 0xe}, -#define XSEM_FUNC2_END 1761 -#define XSEM_FUNC3_START 1761 +#define XSEM_FUNC2_END 1724 +#define XSEM_FUNC3_START 1724 {OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0xc7ec, 0x0}, {OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x2978, 0x100391}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x50f0, 0xe}, -#define XSEM_FUNC3_END 1764 -#define XSEM_FUNC4_START 1764 +#define XSEM_FUNC3_END 1727 +#define XSEM_FUNC4_START 1727 {OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0xc7f0, 0x0}, {OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x29b8, 0x1003a1}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x5128, 0xe}, -#define XSEM_FUNC4_END 1767 -#define XSEM_FUNC5_START 1767 +#define XSEM_FUNC4_END 1730 +#define XSEM_FUNC5_START 1730 {OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0xc7f4, 0x0}, {OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x29f8, 0x1003b1}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x5160, 0xe}, -#define XSEM_FUNC5_END 1770 -#define XSEM_FUNC6_START 1770 +#define XSEM_FUNC5_END 1733 +#define XSEM_FUNC6_START 1733 {OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0xc7f8, 0x0}, {OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x2a38, 0x1003c1}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x5198, 0xe}, -#define XSEM_FUNC6_END 1773 -#define XSEM_FUNC7_START 1773 +#define XSEM_FUNC6_END 1736 +#define XSEM_FUNC7_START 1736 {OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0xc7fc, 0x0}, {OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x2a78, 0x1003d1}, {OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x51d0, 0xe}, -#define XSEM_FUNC7_END 1776 -#define CDU_COMMON_START 1776 +#define XSEM_FUNC7_END 1739 +#define CDU_COMMON_START 1739 {OP_WR, CDU_REG_CDU_CONTROL0, 0x1}, {OP_WR_E1H, CDU_REG_MF_MODE, 0x1}, {OP_WR, CDU_REG_CDU_CHK_MASK0, 0x3d000}, {OP_WR, CDU_REG_CDU_CHK_MASK1, 0x3d}, - {OP_WB_E1, CDU_REG_L1TT, 0x200033f}, + {OP_WB_E1, CDU_REG_L1TT, 0x200033d}, {OP_WB_E1H, CDU_REG_L1TT, 0x20003e1}, - {OP_WB_E1, CDU_REG_MATT, 0x20053f}, + {OP_WB_E1, CDU_REG_MATT, 0x20053d}, {OP_WB_E1H, CDU_REG_MATT, 0x2805e1}, {OP_ZR_E1, CDU_REG_MATT + 0x80, 0x2}, - {OP_WB_E1, CDU_REG_MATT + 0x88, 0x6055f}, + {OP_WB_E1, CDU_REG_MATT + 0x88, 0x6055d}, {OP_ZR, CDU_REG_MATT + 0xa0, 0x18}, -#define CDU_COMMON_END 1787 -#define DMAE_COMMON_START 1787 +#define CDU_COMMON_END 1750 +#define DMAE_COMMON_START 1750 {OP_ZR, DMAE_REG_CMD_MEM, 0xe0}, {OP_WR, DMAE_REG_CRC16C_INIT, 0x0}, {OP_WR, DMAE_REG_CRC16T10_INIT, 0x1}, @@ -2050,24 +2013,24 @@ static const struct raw_op init_ops[] = { {OP_WR_E1H, DMAE_REG_PXP_REQ_INIT_CRD, 0x2}, {OP_WR, DMAE_REG_PCI_IFEN, 0x1}, {OP_WR, DMAE_REG_GRC_IFEN, 0x1}, -#define DMAE_COMMON_END 1794 -#define PXP_COMMON_START 1794 - {OP_WB_E1, PXP_REG_HST_INBOUND_INT + 0x400, 0x50565}, +#define DMAE_COMMON_END 1757 +#define PXP_COMMON_START 1757 + {OP_WB_E1, PXP_REG_HST_INBOUND_INT + 0x400, 0x50563}, {OP_WB_E1H, PXP_REG_HST_INBOUND_INT + 0x400, 0x50609}, - {OP_WB_E1, PXP_REG_HST_INBOUND_INT + 0x420, 0x5056a}, + {OP_WB_E1, PXP_REG_HST_INBOUND_INT + 0x420, 0x50568}, {OP_WB_E1H, PXP_REG_HST_INBOUND_INT, 0x5060e}, - {OP_WB_E1, PXP_REG_HST_INBOUND_INT, 0x5056f}, -#define PXP_COMMON_END 1799 -#define CFC_COMMON_START 1799 + {OP_WB_E1, PXP_REG_HST_INBOUND_INT, 0x5056d}, +#define PXP_COMMON_END 1762 +#define CFC_COMMON_START 1762 {OP_ZR_E1H, CFC_REG_LINK_LIST, 0x100}, {OP_WR, CFC_REG_CONTROL0, 0x10}, {OP_WR, CFC_REG_DISABLE_ON_ERROR, 0x3fff}, {OP_WR, CFC_REG_LCREQ_WEIGHTS, 0x84924a}, -#define CFC_COMMON_END 1803 -#define HC_COMMON_START 1803 +#define CFC_COMMON_END 1766 +#define HC_COMMON_START 1766 {OP_ZR_E1, HC_REG_USTORM_ADDR_FOR_COALESCE, 0x4}, -#define HC_COMMON_END 1804 -#define HC_PORT0_START 1804 +#define HC_COMMON_END 1767 +#define HC_PORT0_START 1767 {OP_WR_E1, HC_REG_CONFIG_0, 0x1080}, {OP_ZR_E1, HC_REG_UC_RAM_ADDR_0, 0x2}, {OP_WR_E1, HC_REG_ATTN_NUM_P0, 0x10}, @@ -2086,8 +2049,8 @@ static const struct raw_op init_ops[] = { {OP_ZR_E1, HC_REG_STATISTIC_COUNTERS + 0x120, 0x4a}, {OP_ZR_E1, HC_REG_STATISTIC_COUNTERS + 0x370, 0x4a}, {OP_ZR_E1, HC_REG_STATISTIC_COUNTERS + 0x5c0, 0x4a}, -#define HC_PORT0_END 1822 -#define HC_PORT1_START 1822 +#define HC_PORT0_END 1785 +#define HC_PORT1_START 1785 {OP_WR_E1, HC_REG_CONFIG_1, 0x1080}, {OP_ZR_E1, HC_REG_UC_RAM_ADDR_1, 0x2}, {OP_WR_E1, HC_REG_ATTN_NUM_P1, 0x10}, @@ -2106,8 +2069,8 @@ static const struct raw_op init_ops[] = { {OP_ZR_E1, HC_REG_STATISTIC_COUNTERS + 0x248, 0x4a}, {OP_ZR_E1, HC_REG_STATISTIC_COUNTERS + 0x498, 0x4a}, {OP_ZR_E1, HC_REG_STATISTIC_COUNTERS + 0x6e8, 0x4a}, -#define HC_PORT1_END 1840 -#define HC_FUNC0_START 1840 +#define HC_PORT1_END 1803 +#define HC_FUNC0_START 1803 {OP_WR_E1H, HC_REG_CONFIG_0, 0x1080}, {OP_WR_E1H, HC_REG_FUNC_NUM_P0, 0x0}, {OP_WR_E1H, HC_REG_ATTN_NUM_P0, 0x10}, @@ -2123,8 +2086,8 @@ static const struct raw_op init_ops[] = { {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x120, 0x4a}, {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x370, 0x4a}, {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x5c0, 0x4a}, -#define HC_FUNC0_END 1855 -#define HC_FUNC1_START 1855 +#define HC_FUNC0_END 1818 +#define HC_FUNC1_START 1818 {OP_WR_E1H, HC_REG_CONFIG_1, 0x1080}, {OP_WR_E1H, HC_REG_FUNC_NUM_P1, 0x1}, {OP_WR_E1H, HC_REG_ATTN_NUM_P1, 0x10}, @@ -2140,8 +2103,8 @@ static const struct raw_op init_ops[] = { {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x248, 0x4a}, {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x498, 0x4a}, {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x6e8, 0x4a}, -#define HC_FUNC1_END 1870 -#define HC_FUNC2_START 1870 +#define HC_FUNC1_END 1833 +#define HC_FUNC2_START 1833 {OP_WR_E1H, HC_REG_CONFIG_0, 0x1080}, {OP_WR_E1H, HC_REG_FUNC_NUM_P0, 0x2}, {OP_WR_E1H, HC_REG_ATTN_NUM_P0, 0x10}, @@ -2157,8 +2120,8 @@ static const struct raw_op init_ops[] = { {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x120, 0x4a}, {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x370, 0x4a}, {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x5c0, 0x4a}, -#define HC_FUNC2_END 1885 -#define HC_FUNC3_START 1885 +#define HC_FUNC2_END 1848 +#define HC_FUNC3_START 1848 {OP_WR_E1H, HC_REG_CONFIG_1, 0x1080}, {OP_WR_E1H, HC_REG_FUNC_NUM_P1, 0x3}, {OP_WR_E1H, HC_REG_ATTN_NUM_P1, 0x10}, @@ -2174,8 +2137,8 @@ static const struct raw_op init_ops[] = { {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x248, 0x4a}, {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x498, 0x4a}, {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x6e8, 0x4a}, -#define HC_FUNC3_END 1900 -#define HC_FUNC4_START 1900 +#define HC_FUNC3_END 1863 +#define HC_FUNC4_START 1863 {OP_WR_E1H, HC_REG_CONFIG_0, 0x1080}, {OP_WR_E1H, HC_REG_FUNC_NUM_P0, 0x4}, {OP_WR_E1H, HC_REG_ATTN_NUM_P0, 0x10}, @@ -2191,8 +2154,8 @@ static const struct raw_op init_ops[] = { {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x120, 0x4a}, {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x370, 0x4a}, {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x5c0, 0x4a}, -#define HC_FUNC4_END 1915 -#define HC_FUNC5_START 1915 +#define HC_FUNC4_END 1878 +#define HC_FUNC5_START 1878 {OP_WR_E1H, HC_REG_CONFIG_1, 0x1080}, {OP_WR_E1H, HC_REG_FUNC_NUM_P1, 0x5}, {OP_WR_E1H, HC_REG_ATTN_NUM_P1, 0x10}, @@ -2208,8 +2171,8 @@ static const struct raw_op init_ops[] = { {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x248, 0x4a}, {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x498, 0x4a}, {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x6e8, 0x4a}, -#define HC_FUNC5_END 1930 -#define HC_FUNC6_START 1930 +#define HC_FUNC5_END 1893 +#define HC_FUNC6_START 1893 {OP_WR_E1H, HC_REG_CONFIG_0, 0x1080}, {OP_WR_E1H, HC_REG_FUNC_NUM_P0, 0x6}, {OP_WR_E1H, HC_REG_ATTN_NUM_P0, 0x10}, @@ -2225,8 +2188,8 @@ static const struct raw_op init_ops[] = { {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x120, 0x4a}, {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x370, 0x4a}, {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x5c0, 0x4a}, -#define HC_FUNC6_END 1945 -#define HC_FUNC7_START 1945 +#define HC_FUNC6_END 1908 +#define HC_FUNC7_START 1908 {OP_WR_E1H, HC_REG_CONFIG_1, 0x1080}, {OP_WR_E1H, HC_REG_FUNC_NUM_P1, 0x7}, {OP_WR_E1H, HC_REG_ATTN_NUM_P1, 0x10}, @@ -2242,8 +2205,8 @@ static const struct raw_op init_ops[] = { {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x248, 0x4a}, {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x498, 0x4a}, {OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x6e8, 0x4a}, -#define HC_FUNC7_END 1960 -#define PXP2_COMMON_START 1960 +#define HC_FUNC7_END 1923 +#define PXP2_COMMON_START 1923 {OP_WR_E1, PXP2_REG_PGL_CONTROL0, 0xe38340}, {OP_WR_E1H, PXP2_REG_RQ_DRAM_ALIGN, 0x1}, {OP_WR, PXP2_REG_PGL_CONTROL1, 0x3c10}, @@ -2361,8 +2324,8 @@ static const struct raw_op init_ops[] = { {OP_WR_E1H, PXP2_REG_RQ_ILT_MODE, 0x1}, {OP_WR, PXP2_REG_RQ_RBC_DONE, 0x1}, {OP_WR_E1H, PXP2_REG_PGL_CONTROL0, 0xe38340}, -#define PXP2_COMMON_END 2077 -#define MISC_AEU_COMMON_START 2077 +#define PXP2_COMMON_END 2040 +#define MISC_AEU_COMMON_START 2040 {OP_ZR, MISC_REG_AEU_GENERAL_ATTN_0, 0x16}, {OP_WR_E1H, MISC_REG_AEU_ENABLE1_NIG_0, 0x55540000}, {OP_WR_E1H, MISC_REG_AEU_ENABLE2_NIG_0, 0x55555555}, @@ -2382,8 +2345,8 @@ static const struct raw_op init_ops[] = { {OP_WR_E1H, MISC_REG_AEU_ENABLE4_PXP_1, 0x0}, {OP_WR_E1H, MISC_REG_AEU_CLR_LATCH_SIGNAL, 0xc00}, {OP_WR_E1H, MISC_REG_AEU_GENERAL_MASK, 0x3}, -#define MISC_AEU_COMMON_END 2096 -#define MISC_AEU_PORT0_START 2096 +#define MISC_AEU_COMMON_END 2059 +#define MISC_AEU_PORT0_START 2059 {OP_WR_E1, MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0, 0xbf5c0000}, {OP_WR_E1H, MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0, 0xff5c0000}, {OP_WR_E1, MISC_REG_AEU_ENABLE2_FUNC_0_OUT_0, 0xfff51fef}, @@ -2416,8 +2379,8 @@ static const struct raw_op init_ops[] = { {OP_WR_E1, MISC_REG_AEU_INVERTER_1_FUNC_0, 0x0}, {OP_ZR_E1, MISC_REG_AEU_INVERTER_2_FUNC_0, 0x3}, {OP_WR_E1, MISC_REG_AEU_MASK_ATTN_FUNC_0, 0x7}, -#define MISC_AEU_PORT0_END 2128 -#define MISC_AEU_PORT1_START 2128 +#define MISC_AEU_PORT0_END 2091 +#define MISC_AEU_PORT1_START 2091 {OP_WR_E1, MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0, 0xbf5c0000}, {OP_WR_E1H, MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0, 0xff5c0000}, {OP_WR_E1, MISC_REG_AEU_ENABLE2_FUNC_1_OUT_0, 0xfff51fef}, @@ -2450,7 +2413,7 @@ static const struct raw_op init_ops[] = { {OP_WR_E1, MISC_REG_AEU_INVERTER_1_FUNC_1, 0x0}, {OP_ZR_E1, MISC_REG_AEU_INVERTER_2_FUNC_1, 0x3}, {OP_WR_E1, MISC_REG_AEU_MASK_ATTN_FUNC_1, 0x7}, -#define MISC_AEU_PORT1_END 2160 +#define MISC_AEU_PORT1_END 2123 }; @@ -2560,103 +2523,92 @@ static const u32 init_data_e1[] = { 0x00049c00, 0x00051f80, 0x0005a300, 0x00062680, 0x0006aa00, 0x00072d80, 0x0007b100, 0x00083480, 0x0008b800, 0x00093b80, 0x0009bf00, 0x000a4280, 0x000ac600, 0x000b4980, 0x000bcd00, 0x000c5080, 0x000cd400, 0x000d5780, - 0x000ddb00, 0x00001900, 0x00000028, 0x00000000, 0x00100000, 0x00000000, - 0x00000000, 0xffffffff, 0x40000000, 0x40000000, 0x40000000, 0x40000000, + 0x000ddb00, 0x00001900, 0x00100000, 0x00000000, 0x00000000, 0xffffffff, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, - 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x00000000, 0x00007ff8, - 0x00000000, 0x00001500, 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, - 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, + 0x40000000, 0x40000000, 0x00000000, 0x00007ff8, 0x00000000, 0x00001500, + 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, + 0xffffffff, 0xffffffff, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, - 0x00000000, 0x00007ff8, 0x00000000, 0x00003500, 0x00001000, 0x00002080, - 0x00003100, 0x00004180, 0x00005200, 0x00006280, 0x00007300, 0x00008380, - 0x00009400, 0x0000a480, 0x0000b500, 0x0000c580, 0x0000d600, 0x0000e680, - 0x0000f700, 0x00010780, 0x00011800, 0x00012880, 0x00013900, 0x00014980, - 0x00015a00, 0x00016a80, 0x00017b00, 0x00018b80, 0x00019c00, 0x0001ac80, - 0x0001bd00, 0x0001cd80, 0x0001de00, 0x0001ee80, 0x0001ff00, 0x00000000, - 0x00010001, 0x00000604, 0xccccccc1, 0xffffffff, 0xffffffff, 0xcccc0201, - 0xcccccccc, 0x00000000, 0xffffffff, 0x40000000, 0x40000000, 0x40000000, + 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x00000000, 0x00007ff8, + 0x00000000, 0x00003500, 0x00001000, 0x00002080, 0x00003100, 0x00004180, + 0x00005200, 0x00006280, 0x00007300, 0x00008380, 0x00009400, 0x0000a480, + 0x0000b500, 0x0000c580, 0x0000d600, 0x0000e680, 0x0000f700, 0x00010780, + 0x00011800, 0x00012880, 0x00013900, 0x00014980, 0x00015a00, 0x00016a80, + 0x00017b00, 0x00018b80, 0x00019c00, 0x0001ac80, 0x0001bd00, 0x0001cd80, + 0x0001de00, 0x0001ee80, 0x0001ff00, 0x00000000, 0x00010001, 0x00000604, + 0xccccccc1, 0xffffffff, 0xffffffff, 0xcccc0201, 0xcccccccc, 0x00000000, + 0xffffffff, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, - 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x40000000, 0x00000000, - 0x00007ff8, 0x00000000, 0x00003500, 0x0000ffff, 0x00000000, 0x0000ffff, + 0x40000000, 0x40000000, 0x40000000, 0x00000000, 0x00007ff8, 0x00000000, + 0x00003500, 0x0000ffff, 0x00000000, 0x0000ffff, 0x00000000, 0x0000ffff, 0x00000000, 0x0000ffff, 0x00000000, 0x0000ffff, 0x00000000, 0x0000ffff, + 0x00000000, 0x0000ffff, 0x00000000, 0x0000ffff, 0x00000000, 0x00100000, 0x00000000, 0x0000ffff, 0x00000000, 0x0000ffff, 0x00000000, 0x0000ffff, - 0x00000000, 0x00100000, 0x00000000, 0x0000ffff, 0x00000000, 0x0000ffff, 0x00000000, 0x0000ffff, 0x00000000, 0x0000ffff, 0x00000000, 0x0000ffff, - 0x00000000, 0x0000ffff, 0x00000000, 0x0000ffff, 0x00000000, 0x0000ffff, - 0x00000000, 0x00100000, 0x00000000, 0xfffffff3, 0x320fffff, 0x0c30c30c, - 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0000cf3c, 0xcdcdcdcd, 0xfffffff1, - 0x30efffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0001cf3c, - 0xcdcdcdcd, 0xfffffff6, 0x305fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, - 0xf3cf3cf3, 0x0002cf3c, 0xcdcdcdcd, 0xfffff406, 0x1cbfffff, 0x0c30c305, - 0xc30c30c3, 0xcf300014, 0xf3cf3cf3, 0x0004cf3c, 0xcdcdcdcd, 0xfffffff2, - 0x304fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0008cf3c, - 0xcdcdcdcd, 0xfffffffa, 0x302fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, - 0xf3cf3cf3, 0x0010cf3c, 0xcdcdcdcd, 0xfffffff7, 0x31efffff, 0x0c30c30c, - 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0020cf3c, 0xcdcdcdcd, 0xfffffff5, - 0x302fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0040cf3c, - 0xcdcdcdcd, 0xfffffff3, 0x310fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, - 0xf3cf3cf3, 0x0000cf3c, 0xcdcdcdcd, 0xfffffff1, 0x310fffff, 0x0c30c30c, + 0x00000000, 0x0000ffff, 0x00000000, 0x0000ffff, 0x00000000, 0x00100000, + 0x00000000, 0xfffffff3, 0x320fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, + 0xf3cf3cf3, 0x0000cf3c, 0xcdcdcdcd, 0xfffffff1, 0x30efffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0001cf3c, 0xcdcdcdcd, 0xfffffff6, 0x305fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0002cf3c, 0xcdcdcdcd, 0xfffff406, 0x1cbfffff, 0x0c30c305, 0xc30c30c3, 0xcf300014, 0xf3cf3cf3, 0x0004cf3c, 0xcdcdcdcd, 0xfffffff2, 0x304fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0008cf3c, 0xcdcdcdcd, 0xfffffffa, 0x302fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0010cf3c, - 0xcdcdcdcd, 0xfffffff7, 0x30efffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, - 0xf3cf3cf3, 0x0020cf3c, 0xcdcdcdcd, 0xfffffff5, 0x304fffff, 0x0c30c30c, + 0xcdcdcdcd, 0xfffffff7, 0x31efffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, + 0xf3cf3cf3, 0x0020cf3c, 0xcdcdcdcd, 0xfffffff5, 0x302fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0040cf3c, 0xcdcdcdcd, 0xfffffff3, - 0x31efffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0000cf3c, + 0x310fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0000cf3c, 0xcdcdcdcd, 0xfffffff1, 0x310fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0001cf3c, 0xcdcdcdcd, 0xfffffff6, 0x305fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0002cf3c, 0xcdcdcdcd, 0xfffff406, 0x1cbfffff, 0x0c30c305, 0xc30c30c3, 0xcf300014, 0xf3cf3cf3, 0x0004cf3c, 0xcdcdcdcd, 0xfffffff2, 0x304fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0008cf3c, 0xcdcdcdcd, 0xfffffffa, 0x302fffff, 0x0c30c30c, - 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0010cf3c, 0xcdcdcdcd, 0xffffff97, - 0x056fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cc000, 0xf3cf3cf3, 0x0020cf3c, - 0xcdcdcdcd, 0xfffffff5, 0x310fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, - 0xf3cf3cf3, 0x0040cf3c, 0xcdcdcdcd, 0xfffffff3, 0x320fffff, 0x0c30c30c, + 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0010cf3c, 0xcdcdcdcd, 0xfffffff7, + 0x30efffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0020cf3c, + 0xcdcdcdcd, 0xfffffff5, 0x304fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, + 0xf3cf3cf3, 0x0040cf3c, 0xcdcdcdcd, 0xfffffff3, 0x31efffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0000cf3c, 0xcdcdcdcd, 0xfffffff1, 0x310fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0001cf3c, 0xcdcdcdcd, 0xfffffff6, 0x305fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0002cf3c, 0xcdcdcdcd, 0xfffff406, 0x1cbfffff, 0x0c30c305, 0xc30c30c3, 0xcf300014, 0xf3cf3cf3, 0x0004cf3c, 0xcdcdcdcd, 0xfffffff2, 0x304fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0008cf3c, - 0xcdcdcdcd, 0xffffff8a, 0x042fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cc000, - 0xf3cf3cf3, 0x0010cf3c, 0xcdcdcdcd, 0xffffff97, 0x05cfffff, 0x0c30c30c, + 0xcdcdcdcd, 0xfffffffa, 0x302fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, + 0xf3cf3cf3, 0x0010cf3c, 0xcdcdcdcd, 0xffffff97, 0x056fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cc000, 0xf3cf3cf3, 0x0020cf3c, 0xcdcdcdcd, 0xfffffff5, 0x310fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0040cf3c, - 0xcdcdcdcd, 0xfffffff3, 0x300fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, - 0xf3cf3cf3, 0x0000cf3c, 0xcdcdcdcd, 0xfffffff1, 0x300fffff, 0x0c30c30c, + 0xcdcdcdcd, 0xfffffff3, 0x320fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, + 0xf3cf3cf3, 0x0000cf3c, 0xcdcdcdcd, 0xfffffff1, 0x310fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0001cf3c, 0xcdcdcdcd, 0xfffffff6, 0x305fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0002cf3c, 0xcdcdcdcd, 0xfffff406, 0x1cbfffff, 0x0c30c305, 0xc30c30c3, 0xcf300014, 0xf3cf3cf3, 0x0004cf3c, 0xcdcdcdcd, 0xfffffff2, 0x304fffff, 0x0c30c30c, - 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0008cf3c, 0xcdcdcdcd, 0xfffffffa, - 0x302fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0010cf3c, - 0xcdcdcdcd, 0xffffff97, 0x040fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cc000, - 0xf3cf3cf3, 0x0020cf3c, 0xcdcdcdcd, 0xfffffff5, 0x300fffff, 0x0c30c30c, - 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0040cf3c, 0xcdcdcdcd, 0xffffffff, - 0x30cfffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf3cc, 0xf3cf3cf3, 0x0000cf3c, - 0xcdcdcdcd, 0xffffffff, 0x30cfffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf3cc, - 0xf3cf3cf3, 0x0001cf3c, 0xcdcdcdcd, 0xffffffff, 0x30cfffff, 0x0c30c30c, - 0xc30c30c3, 0xcf3cf3cc, 0xf3cf3cf3, 0x0002cf3c, 0xcdcdcdcd, 0xffffffff, - 0x30cfffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf3cc, 0xf3cf3cf3, 0x0004cf3c, - 0xcdcdcdcd, 0xffffffff, 0x30cfffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf3cc, - 0xf3cf3cf3, 0x0008cf3c, 0xcdcdcdcd, 0xffffffff, 0x30cfffff, 0x0c30c30c, - 0xc30c30c3, 0xcf3cf3cc, 0xf3cf3cf3, 0x0010cf3c, 0xcdcdcdcd, 0xffffffff, - 0x30cfffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf3cc, 0xf3cf3cf3, 0x0020cf3c, - 0xcdcdcdcd, 0xffffffff, 0x30cfffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf3cc, + 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0008cf3c, 0xcdcdcdcd, 0xffffff8a, + 0x042fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cc000, 0xf3cf3cf3, 0x0010cf3c, + 0xcdcdcdcd, 0xffffff97, 0x05cfffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cc000, + 0xf3cf3cf3, 0x0020cf3c, 0xcdcdcdcd, 0xfffffff5, 0x310fffff, 0x0c30c30c, + 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0040cf3c, 0xcdcdcdcd, 0xfffffff3, + 0x300fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0000cf3c, + 0xcdcdcdcd, 0xfffffff1, 0x300fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, + 0xf3cf3cf3, 0x0001cf3c, 0xcdcdcdcd, 0xfffffff6, 0x305fffff, 0x0c30c30c, + 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0002cf3c, 0xcdcdcdcd, 0xfffff406, + 0x1cbfffff, 0x0c30c305, 0xc30c30c3, 0xcf300014, 0xf3cf3cf3, 0x0004cf3c, + 0xcdcdcdcd, 0xfffffff2, 0x304fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, + 0xf3cf3cf3, 0x0008cf3c, 0xcdcdcdcd, 0xfffffffa, 0x302fffff, 0x0c30c30c, + 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0010cf3c, 0xcdcdcdcd, 0xffffff97, + 0x040fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cc000, 0xf3cf3cf3, 0x0020cf3c, + 0xcdcdcdcd, 0xfffffff5, 0x300fffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf300, 0xf3cf3cf3, 0x0040cf3c, 0xcdcdcdcd, 0xffffffff, 0x30cfffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf3cc, 0xf3cf3cf3, 0x0000cf3c, 0xcdcdcdcd, 0xffffffff, 0x30cfffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf3cc, 0xf3cf3cf3, 0x0001cf3c, @@ -2678,16 +2630,27 @@ static const u32 init_data_e1[] = { 0x30cfffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf3cc, 0xf3cf3cf3, 0x0010cf3c, 0xcdcdcdcd, 0xffffffff, 0x30cfffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf3cc, 0xf3cf3cf3, 0x0020cf3c, 0xcdcdcdcd, 0xffffffff, 0x30cfffff, 0x0c30c30c, - 0xc30c30c3, 0xcf3cf3cc, 0xf3cf3cf3, 0x0040cf3c, 0xcdcdcdcd, 0x00100000, - 0x00070100, 0x00028170, 0x000b8198, 0x00020250, 0x00010270, 0x000f0280, - 0x00010370, 0x00080000, 0x00080080, 0x00028100, 0x000b8128, 0x000201e0, - 0x00010200, 0x00070210, 0x00020280, 0x000f0000, 0x000800f0, 0x00028170, - 0x000b8198, 0x00020250, 0x00010270, 0x000b8280, 0x00080338, 0x00100000, - 0x00080100, 0x00028180, 0x000b81a8, 0x00020260, 0x00018280, 0x000e8298, - 0x00080380, 0x00028000, 0x000b8028, 0x000200e0, 0x00010100, 0x00008110, - 0x00000118, 0xcccccccc, 0xcccccccc, 0xcccccccc, 0xcccccccc, 0x00002000, - 0xcccccccc, 0xcccccccc, 0xcccccccc, 0xcccccccc, 0x00002000, 0xcccccccc, - 0xcccccccc, 0xcccccccc, 0xcccccccc, 0x00002000 + 0xc30c30c3, 0xcf3cf3cc, 0xf3cf3cf3, 0x0040cf3c, 0xcdcdcdcd, 0xffffffff, + 0x30cfffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf3cc, 0xf3cf3cf3, 0x0000cf3c, + 0xcdcdcdcd, 0xffffffff, 0x30cfffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf3cc, + 0xf3cf3cf3, 0x0001cf3c, 0xcdcdcdcd, 0xffffffff, 0x30cfffff, 0x0c30c30c, + 0xc30c30c3, 0xcf3cf3cc, 0xf3cf3cf3, 0x0002cf3c, 0xcdcdcdcd, 0xffffffff, + 0x30cfffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf3cc, 0xf3cf3cf3, 0x0004cf3c, + 0xcdcdcdcd, 0xffffffff, 0x30cfffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf3cc, + 0xf3cf3cf3, 0x0008cf3c, 0xcdcdcdcd, 0xffffffff, 0x30cfffff, 0x0c30c30c, + 0xc30c30c3, 0xcf3cf3cc, 0xf3cf3cf3, 0x0010cf3c, 0xcdcdcdcd, 0xffffffff, + 0x30cfffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf3cc, 0xf3cf3cf3, 0x0020cf3c, + 0xcdcdcdcd, 0xffffffff, 0x30cfffff, 0x0c30c30c, 0xc30c30c3, 0xcf3cf3cc, + 0xf3cf3cf3, 0x0040cf3c, 0xcdcdcdcd, 0x00100000, 0x00070100, 0x00028170, + 0x000b8198, 0x00020250, 0x00010270, 0x000f0280, 0x00010370, 0x00080000, + 0x00080080, 0x00028100, 0x000b8128, 0x000201e0, 0x00010200, 0x00070210, + 0x00020280, 0x000f0000, 0x000800f0, 0x00028170, 0x000b8198, 0x00020250, + 0x00010270, 0x000b8280, 0x00080338, 0x00100000, 0x00080100, 0x00028180, + 0x000b81a8, 0x00020260, 0x00018280, 0x000e8298, 0x00080380, 0x00028000, + 0x000b8028, 0x000200e0, 0x00010100, 0x00008110, 0x00000118, 0xcccccccc, + 0xcccccccc, 0xcccccccc, 0xcccccccc, 0x00002000, 0xcccccccc, 0xcccccccc, + 0xcccccccc, 0xcccccccc, 0x00002000, 0xcccccccc, 0xcccccccc, 0xcccccccc, + 0xcccccccc, 0x00002000 }; static const u32 init_data_e1h[] = { diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index ac46228cc9d..6115161334a 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -2975,37 +2975,6 @@ static inline long bnx2x_hilo(u32 *hiref) * Init service functions */ -static void bnx2x_storm_stats_init(struct bnx2x *bp) -{ - int func = BP_FUNC(bp); - - REG_WR(bp, BAR_XSTRORM_INTMEM + XSTORM_STATS_FLAGS_OFFSET(func), 1); - REG_WR(bp, BAR_XSTRORM_INTMEM + - XSTORM_STATS_FLAGS_OFFSET(func) + 4, 0); - - REG_WR(bp, BAR_TSTRORM_INTMEM + TSTORM_STATS_FLAGS_OFFSET(func), 1); - REG_WR(bp, BAR_TSTRORM_INTMEM + - TSTORM_STATS_FLAGS_OFFSET(func) + 4, 0); - - REG_WR(bp, BAR_CSTRORM_INTMEM + CSTORM_STATS_FLAGS_OFFSET(func), 0); - REG_WR(bp, BAR_CSTRORM_INTMEM + - CSTORM_STATS_FLAGS_OFFSET(func) + 4, 0); - - REG_WR(bp, BAR_XSTRORM_INTMEM + - XSTORM_ETH_STATS_QUERY_ADDR_OFFSET(func), - U64_LO(bnx2x_sp_mapping(bp, fw_stats))); - REG_WR(bp, BAR_XSTRORM_INTMEM + - XSTORM_ETH_STATS_QUERY_ADDR_OFFSET(func) + 4, - U64_HI(bnx2x_sp_mapping(bp, fw_stats))); - - REG_WR(bp, BAR_TSTRORM_INTMEM + - TSTORM_ETH_STATS_QUERY_ADDR_OFFSET(func), - U64_LO(bnx2x_sp_mapping(bp, fw_stats))); - REG_WR(bp, BAR_TSTRORM_INTMEM + - TSTORM_ETH_STATS_QUERY_ADDR_OFFSET(func) + 4, - U64_HI(bnx2x_sp_mapping(bp, fw_stats))); -} - static void bnx2x_storm_stats_post(struct bnx2x *bp) { if (!bp->stats_pending) { @@ -4632,13 +4601,35 @@ static void bnx2x_set_storm_rx_mode(struct bnx2x *bp) bnx2x_set_client_config(bp); } -static void bnx2x_init_internal(struct bnx2x *bp) +static void bnx2x_init_internal_common(struct bnx2x *bp) +{ + int i; + + /* Zero this manually as its initialization is + currently missing in the initTool */ + for (i = 0; i < (USTORM_AGG_DATA_SIZE >> 2); i++) + REG_WR(bp, BAR_USTRORM_INTMEM + + USTORM_AGG_DATA_OFFSET + i * 4, 0); +} + +static void bnx2x_init_internal_port(struct bnx2x *bp) +{ + int port = BP_PORT(bp); + + REG_WR(bp, BAR_USTRORM_INTMEM + USTORM_HC_BTR_OFFSET(port), BNX2X_BTR); + REG_WR(bp, BAR_CSTRORM_INTMEM + CSTORM_HC_BTR_OFFSET(port), BNX2X_BTR); + REG_WR(bp, BAR_TSTRORM_INTMEM + TSTORM_HC_BTR_OFFSET(port), BNX2X_BTR); + REG_WR(bp, BAR_XSTRORM_INTMEM + XSTORM_HC_BTR_OFFSET(port), BNX2X_BTR); +} + +static void bnx2x_init_internal_func(struct bnx2x *bp) { struct tstorm_eth_function_common_config tstorm_config = {0}; struct stats_indication_flags stats_flags = {0}; int port = BP_PORT(bp); int func = BP_FUNC(bp); int i; + u16 max_agg_size; if (is_multi(bp)) { tstorm_config.config_flags = MULTI_FLAGS; @@ -4651,9 +4642,6 @@ static void bnx2x_init_internal(struct bnx2x *bp) TSTORM_FUNCTION_COMMON_CONFIG_OFFSET(func), (*(u32 *)&tstorm_config)); -/* DP(NETIF_MSG_IFUP, "tstorm_config: 0x%08x\n", - (*(u32 *)&tstorm_config)); */ - bp->rx_mode = BNX2X_RX_MODE_NONE; /* no rx until link is up */ bnx2x_set_storm_rx_mode(bp); @@ -4716,15 +4704,12 @@ static void bnx2x_init_internal(struct bnx2x *bp) bp->e1hov); } - /* Zero this manualy as its initialization is - currently missing in the initTool */ - for (i = 0; i < USTORM_AGG_DATA_SIZE >> 2; i++) - REG_WR(bp, BAR_USTRORM_INTMEM + - USTORM_AGG_DATA_OFFSET + 4*i, 0); - + /* Init CQ ring mapping and aggregation size */ + max_agg_size = min((u32)(bp->rx_buf_use_size + + 8*BCM_PAGE_SIZE*PAGES_PER_SGE), + (u32)0xffff); for_each_queue(bp, i) { struct bnx2x_fastpath *fp = &bp->fp[i]; - u16 max_agg_size; REG_WR(bp, BAR_USTRORM_INTMEM + USTORM_CQE_PAGE_BASE_OFFSET(port, FP_CL_ID(fp)), @@ -4733,16 +4718,34 @@ static void bnx2x_init_internal(struct bnx2x *bp) USTORM_CQE_PAGE_BASE_OFFSET(port, FP_CL_ID(fp)) + 4, U64_HI(fp->rx_comp_mapping)); - max_agg_size = min((u32)(bp->rx_buf_use_size + - 8*BCM_PAGE_SIZE*PAGES_PER_SGE), - (u32)0xffff); REG_WR16(bp, BAR_USTRORM_INTMEM + USTORM_MAX_AGG_SIZE_OFFSET(port, FP_CL_ID(fp)), max_agg_size); } } -static void bnx2x_nic_init(struct bnx2x *bp) +static void bnx2x_init_internal(struct bnx2x *bp, u32 load_code) +{ + switch (load_code) { + case FW_MSG_CODE_DRV_LOAD_COMMON: + bnx2x_init_internal_common(bp); + /* no break */ + + case FW_MSG_CODE_DRV_LOAD_PORT: + bnx2x_init_internal_port(bp); + /* no break */ + + case FW_MSG_CODE_DRV_LOAD_FUNCTION: + bnx2x_init_internal_func(bp); + break; + + default: + BNX2X_ERR("Unknown load_code (0x%x) from MCP\n", load_code); + break; + } +} + +static void bnx2x_nic_init(struct bnx2x *bp, u32 load_code) { int i; @@ -4768,8 +4771,7 @@ static void bnx2x_nic_init(struct bnx2x *bp) bnx2x_init_tx_ring(bp); bnx2x_init_sp_ring(bp); bnx2x_init_context(bp); - bnx2x_init_internal(bp); - bnx2x_storm_stats_init(bp); + bnx2x_init_internal(bp, load_code); bnx2x_init_ind_table(bp); bnx2x_int_enable(bp); } @@ -6325,7 +6327,7 @@ static int bnx2x_nic_load(struct bnx2x *bp, int load_mode) atomic_set(&bp->intr_sem, 0); /* Setup NIC internals and enable interrupts */ - bnx2x_nic_init(bp); + bnx2x_nic_init(bp, load_code); /* Send LOAD_DONE command to MCP */ if (!BP_NOMCP(bp)) { -- GitLab From da5a662a2326931bef25f0e534c9c1702f862399 Mon Sep 17 00:00:00 2001 From: Vladislav Zolotarov Date: Wed, 13 Aug 2008 15:50:00 -0700 Subject: [PATCH 248/750] bnx2x: Load/Unload under traffic Load/Unload under traffic Few issues were found when loading and unloading under traffic: - When receiving Tx interrupt call netif_wake_queue if the queue is stopped but the state is open - Check that interrupts are enabled before doing anything else on the msix_fp_int function - In nic_load, enable the interrupts only when needed and ready for it - Function stop_leading returns status since it can fail - Add 1ms delay when unloading the driver to validate that there are no open transactions that already started by the FW - Splitting the "has work" function into Tx and Rx so the same function will be used on unload and interrupts - Do not request for WoL if only resetting the device (save the time that it takes the FW to set the link after reset) - Fixing the device reset after iSCSI boot and before driver load - all internal buffers must be cleared before the driver is loaded Signed-off-by: Vladislav Zolotarov Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x.h | 9 ++ drivers/net/bnx2x_main.c | 221 ++++++++++++++++++++++----------------- drivers/net/bnx2x_reg.h | 3 + 3 files changed, 135 insertions(+), 98 deletions(-) diff --git a/drivers/net/bnx2x.h b/drivers/net/bnx2x.h index 9cbf0e82ef3..b9aa6f48ae2 100644 --- a/drivers/net/bnx2x.h +++ b/drivers/net/bnx2x.h @@ -274,6 +274,15 @@ struct bnx2x_fastpath { #define bnx2x_fp(bp, nr, var) (bp->fp[nr].var) +#define BNX2X_HAS_TX_WORK(fp) \ + ((fp->tx_pkt_prod != le16_to_cpu(*fp->tx_cons_sb)) || \ + (fp->tx_pkt_prod != fp->tx_pkt_cons)) + +#define BNX2X_HAS_RX_WORK(fp) \ + (fp->rx_comp_cons != le16_to_cpu(*fp->rx_cons_sb)) + +#define BNX2X_HAS_WORK(fp) (BNX2X_HAS_RX_WORK(fp) || BNX2X_HAS_TX_WORK(fp)) + /* MC hsi */ #define MAX_FETCH_BD 13 /* HW max BDs per packet */ diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index 6115161334a..dfa8c7b00cb 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -717,21 +717,6 @@ static inline u16 bnx2x_update_fpsb_idx(struct bnx2x_fastpath *fp) return rc; } -static inline int bnx2x_has_work(struct bnx2x_fastpath *fp) -{ - u16 rx_cons_sb = le16_to_cpu(*fp->rx_cons_sb); - - if ((rx_cons_sb & MAX_RCQ_DESC_CNT) == MAX_RCQ_DESC_CNT) - rx_cons_sb++; - - if ((fp->rx_comp_cons != rx_cons_sb) || - (fp->tx_pkt_prod != le16_to_cpu(*fp->tx_cons_sb)) || - (fp->tx_pkt_prod != fp->tx_pkt_cons)) - return 1; - - return 0; -} - static u16 bnx2x_ack_int(struct bnx2x *bp) { u32 igu_addr = (IGU_ADDR_SIMD_MASK + IGU_FUNC_BASE * BP_FUNC(bp)) * 8; @@ -899,6 +884,7 @@ static void bnx2x_tx_int(struct bnx2x_fastpath *fp, int work) netif_tx_lock(bp->dev); if (netif_queue_stopped(bp->dev) && + (bp->state == BNX2X_STATE_OPEN) && (bnx2x_tx_avail(fp) >= MAX_SKB_FRAGS + 3)) netif_wake_queue(bp->dev); @@ -1617,6 +1603,12 @@ static irqreturn_t bnx2x_msix_fp_int(int irq, void *fp_cookie) struct net_device *dev = bp->dev; int index = FP_IDX(fp); + /* Return here if interrupt is disabled */ + if (unlikely(atomic_read(&bp->intr_sem) != 0)) { + DP(NETIF_MSG_INTR, "called but intr_sem not 0, returning\n"); + return IRQ_HANDLED; + } + DP(BNX2X_MSG_FP, "got an MSI-X interrupt on IDX:SB [%d:%d]\n", index, FP_SB_ID(fp)); bnx2x_ack_sb(bp, FP_SB_ID(fp), USTORM_ID, 0, IGU_INT_DISABLE, 0); @@ -6230,22 +6222,24 @@ static int bnx2x_nic_load(struct bnx2x *bp, int load_mode) if (!BP_NOMCP(bp)) { load_code = bnx2x_fw_command(bp, DRV_MSG_CODE_LOAD_REQ); if (!load_code) { - BNX2X_ERR("MCP response failure, unloading\n"); + BNX2X_ERR("MCP response failure, aborting\n"); return -EBUSY; } if (load_code == FW_MSG_CODE_DRV_LOAD_REFUSED) return -EBUSY; /* other port in diagnostic mode */ } else { + int port = BP_PORT(bp); + DP(NETIF_MSG_IFUP, "NO MCP load counts before us %d, %d, %d\n", load_count[0], load_count[1], load_count[2]); load_count[0]++; - load_count[1 + BP_PORT(bp)]++; + load_count[1 + port]++; DP(NETIF_MSG_IFUP, "NO MCP new load counts %d, %d, %d\n", load_count[0], load_count[1], load_count[2]); if (load_count[0] == 1) load_code = FW_MSG_CODE_DRV_LOAD_COMMON; - else if (load_count[1 + BP_PORT(bp)] == 1) + else if (load_count[1 + port] == 1) load_code = FW_MSG_CODE_DRV_LOAD_PORT; else load_code = FW_MSG_CODE_DRV_LOAD_FUNCTION; @@ -6294,9 +6288,6 @@ static int bnx2x_nic_load(struct bnx2x *bp, int load_mode) bnx2x_fp(bp, i, disable_tpa) = ((bp->flags & TPA_ENABLE_FLAG) == 0); - /* Disable interrupt handling until HW is initialized */ - atomic_set(&bp->intr_sem, 1); - if (bp->flags & USING_MSIX_FLAG) { rc = bnx2x_req_msix_irqs(bp); if (rc) { @@ -6323,9 +6314,6 @@ static int bnx2x_nic_load(struct bnx2x *bp, int load_mode) goto load_error; } - /* Enable interrupt handling */ - atomic_set(&bp->intr_sem, 0); - /* Setup NIC internals and enable interrupts */ bnx2x_nic_init(bp, load_code); @@ -6333,7 +6321,7 @@ static int bnx2x_nic_load(struct bnx2x *bp, int load_mode) if (!BP_NOMCP(bp)) { load_code = bnx2x_fw_command(bp, DRV_MSG_CODE_LOAD_DONE); if (!load_code) { - BNX2X_ERR("MCP response failure, unloading\n"); + BNX2X_ERR("MCP response failure, aborting\n"); rc = -EBUSY; goto load_int_disable; } @@ -6348,11 +6336,12 @@ static int bnx2x_nic_load(struct bnx2x *bp, int load_mode) for_each_queue(bp, i) napi_enable(&bnx2x_fp(bp, i, napi)); + /* Enable interrupt handling */ + atomic_set(&bp->intr_sem, 0); + rc = bnx2x_setup_leading(bp); if (rc) { -#ifdef BNX2X_STOP_ON_ERROR - bp->panic = 1; -#endif + BNX2X_ERR("Setup leading failed!\n"); goto load_stop_netif; } @@ -6386,7 +6375,6 @@ static int bnx2x_nic_load(struct bnx2x *bp, int load_mode) break; case LOAD_OPEN: - /* IRQ is only requested from bnx2x_open */ netif_start_queue(bp->dev); bnx2x_set_rx_mode(bp->dev); if (bp->flags & USING_MSIX_FLAG) @@ -6458,7 +6446,7 @@ static int bnx2x_stop_multi(struct bnx2x *bp, int index) return rc; } -static void bnx2x_stop_leading(struct bnx2x *bp) +static int bnx2x_stop_leading(struct bnx2x *bp) { u16 dsb_sp_prod_idx; /* if the other port is handling traffic, @@ -6476,7 +6464,7 @@ static void bnx2x_stop_leading(struct bnx2x *bp) rc = bnx2x_wait_ramrod(bp, BNX2X_FP_STATE_HALTED, 0, &(bp->fp[0].state), 1); if (rc) /* timeout */ - return; + return rc; dsb_sp_prod_idx = *bp->dsb_sp_prod; @@ -6495,13 +6483,18 @@ static void bnx2x_stop_leading(struct bnx2x *bp) *bp->dsb_sp_prod, dsb_sp_prod_idx); #ifdef BNX2X_STOP_ON_ERROR bnx2x_panic(); +#else + rc = -EBUSY; #endif break; } cnt--; + msleep(1); } bp->state = BNX2X_STATE_CLOSING_WAIT4_UNLOAD; bp->fp[0].state = BNX2X_FP_STATE_CLOSED; + + return rc; } static void bnx2x_reset_func(struct bnx2x *bp) @@ -6586,8 +6579,9 @@ static void bnx2x_reset_chip(struct bnx2x *bp, u32 reset_code) /* msut be called with rtnl_lock */ static int bnx2x_nic_unload(struct bnx2x *bp, int unload_mode) { + int port = BP_PORT(bp); u32 reset_code = 0; - int i, cnt; + int i, cnt, rc; bp->state = BNX2X_STATE_CLOSING_WAIT4_HALT; @@ -6604,22 +6598,17 @@ static int bnx2x_nic_unload(struct bnx2x *bp, int unload_mode) (DRV_PULSE_ALWAYS_ALIVE | bp->fw_drv_pulse_wr_seq)); bnx2x_stats_handle(bp, STATS_EVENT_STOP); - /* Wait until all fast path tasks complete */ + /* Wait until tx fast path tasks complete */ for_each_queue(bp, i) { struct bnx2x_fastpath *fp = &bp->fp[i]; -#ifdef BNX2X_STOP_ON_ERROR -#ifdef __powerpc64__ - DP(NETIF_MSG_RX_STATUS, "fp->tpa_queue_used = 0x%lx\n", -#else - DP(NETIF_MSG_IFDOWN, "fp->tpa_queue_used = 0x%llx\n", -#endif - fp->tpa_queue_used); -#endif cnt = 1000; smp_rmb(); - while (bnx2x_has_work(fp)) { - msleep(1); + while (BNX2X_HAS_TX_WORK(fp)) { + + if (!netif_running(bp->dev)) + bnx2x_tx_int(fp, 1000); + if (!cnt) { BNX2X_ERR("timeout waiting for queue[%d]\n", i); @@ -6631,14 +6620,13 @@ static int bnx2x_nic_unload(struct bnx2x *bp, int unload_mode) #endif } cnt--; + msleep(1); smp_rmb(); } } - /* Wait until all slow path tasks complete */ - cnt = 1000; - while ((bp->spq_left != MAX_SPQ_PENDING) && cnt--) - msleep(1); + /* Give HW time to discard old tx messages */ + msleep(1); for_each_queue(bp, i) napi_disable(&bnx2x_fp(bp, i, napi)); @@ -6648,52 +6636,51 @@ static int bnx2x_nic_unload(struct bnx2x *bp, int unload_mode) /* Release IRQs */ bnx2x_free_irq(bp); - if (bp->flags & NO_WOL_FLAG) + if (unload_mode == UNLOAD_NORMAL) + reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS; + + else if (bp->flags & NO_WOL_FLAG) { reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_MCP; + if (CHIP_IS_E1H(bp)) + REG_WR(bp, MISC_REG_E1HMF_MODE, 0); - else if (bp->wol) { - u32 emac_base = BP_PORT(bp) ? GRCBASE_EMAC1 : GRCBASE_EMAC0; + } else if (bp->wol) { + u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0; u8 *mac_addr = bp->dev->dev_addr; u32 val; - /* The mac address is written to entries 1-4 to preserve entry 0 which is used by the PMF */ + u8 entry = (BP_E1HVN(bp) + 1)*8; + val = (mac_addr[0] << 8) | mac_addr[1]; - EMAC_WR(EMAC_REG_EMAC_MAC_MATCH + (BP_E1HVN(bp) + 1)*8, val); + EMAC_WR(EMAC_REG_EMAC_MAC_MATCH + entry, val); val = (mac_addr[2] << 24) | (mac_addr[3] << 16) | (mac_addr[4] << 8) | mac_addr[5]; - EMAC_WR(EMAC_REG_EMAC_MAC_MATCH + (BP_E1HVN(bp) + 1)*8 + 4, - val); + EMAC_WR(EMAC_REG_EMAC_MAC_MATCH + entry + 4, val); reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_EN; } else reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS; + if (CHIP_IS_E1H(bp)) + REG_WR(bp, NIG_REG_LLH0_FUNC_EN + port*8, 0); + /* Close multi and leading connections Completions for ramrods are collected in a synchronous way */ for_each_nondefault_queue(bp, i) if (bnx2x_stop_multi(bp, i)) goto unload_error; - if (CHIP_IS_E1H(bp)) - REG_WR(bp, NIG_REG_LLH0_FUNC_EN + BP_PORT(bp)*8, 0); - - bnx2x_stop_leading(bp); -#ifdef BNX2X_STOP_ON_ERROR - /* If ramrod completion timed out - break here! */ - if (bp->panic) { + rc = bnx2x_stop_leading(bp); + if (rc) { BNX2X_ERR("Stop leading failed!\n"); +#ifdef BNX2X_STOP_ON_ERROR return -EBUSY; - } +#else + goto unload_error; #endif - - if ((bp->state != BNX2X_STATE_CLOSING_WAIT4_UNLOAD) || - (bp->fp[0].state != BNX2X_FP_STATE_CLOSED)) { - DP(NETIF_MSG_IFDOWN, "failed to close leading properly! " - "state 0x%x fp[0].state 0x%x\n", - bp->state, bp->fp[0].state); } unload_error: @@ -6703,12 +6690,12 @@ unload_error: DP(NETIF_MSG_IFDOWN, "NO MCP load counts %d, %d, %d\n", load_count[0], load_count[1], load_count[2]); load_count[0]--; - load_count[1 + BP_PORT(bp)]--; + load_count[1 + port]--; DP(NETIF_MSG_IFDOWN, "NO MCP new load counts %d, %d, %d\n", load_count[0], load_count[1], load_count[2]); if (load_count[0] == 0) reset_code = FW_MSG_CODE_DRV_UNLOAD_COMMON; - else if (load_count[1 + BP_PORT(bp)] == 0) + else if (load_count[1 + port] == 0) reset_code = FW_MSG_CODE_DRV_UNLOAD_PORT; else reset_code = FW_MSG_CODE_DRV_UNLOAD_FUNCTION; @@ -6780,50 +6767,86 @@ static void __devinit bnx2x_undi_unload(struct bnx2x *bp) /* Check if it is the UNDI driver * UNDI driver initializes CID offset for normal bell to 0x7 */ + bnx2x_hw_lock(bp, HW_LOCK_RESOURCE_UNDI); val = REG_RD(bp, DORQ_REG_NORM_CID_OFST); if (val == 0x7) { u32 reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS; - /* save our func and fw_seq */ + /* save our func */ int func = BP_FUNC(bp); - u16 fw_seq = bp->fw_seq; + u32 swap_en; + u32 swap_val; BNX2X_DEV_INFO("UNDI is active! reset device\n"); /* try unload UNDI on port 0 */ bp->func = 0; - bp->fw_seq = (SHMEM_RD(bp, - func_mb[bp->func].drv_mb_header) & - DRV_MSG_SEQ_NUMBER_MASK); - + bp->fw_seq = + (SHMEM_RD(bp, func_mb[bp->func].drv_mb_header) & + DRV_MSG_SEQ_NUMBER_MASK); reset_code = bnx2x_fw_command(bp, reset_code); - bnx2x_fw_command(bp, DRV_MSG_CODE_UNLOAD_DONE); /* if UNDI is loaded on the other port */ if (reset_code != FW_MSG_CODE_DRV_UNLOAD_COMMON) { + /* send "DONE" for previous unload */ + bnx2x_fw_command(bp, DRV_MSG_CODE_UNLOAD_DONE); + + /* unload UNDI on port 1 */ bp->func = 1; - bp->fw_seq = (SHMEM_RD(bp, - func_mb[bp->func].drv_mb_header) & - DRV_MSG_SEQ_NUMBER_MASK); - - bnx2x_fw_command(bp, - DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS); - bnx2x_fw_command(bp, - DRV_MSG_CODE_UNLOAD_DONE); - - /* restore our func and fw_seq */ - bp->func = func; - bp->fw_seq = fw_seq; + bp->fw_seq = + (SHMEM_RD(bp, func_mb[bp->func].drv_mb_header) & + DRV_MSG_SEQ_NUMBER_MASK); + reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS; + + bnx2x_fw_command(bp, reset_code); } + REG_WR(bp, (BP_PORT(bp) ? HC_REG_CONFIG_1 : + HC_REG_CONFIG_0), 0x1000); + + /* close input traffic and wait for it */ + /* Do not rcv packets to BRB */ + REG_WR(bp, + (BP_PORT(bp) ? NIG_REG_LLH1_BRB1_DRV_MASK : + NIG_REG_LLH0_BRB1_DRV_MASK), 0x0); + /* Do not direct rcv packets that are not for MCP to + * the BRB */ + REG_WR(bp, + (BP_PORT(bp) ? NIG_REG_LLH1_BRB1_NOT_MCP : + NIG_REG_LLH0_BRB1_NOT_MCP), 0x0); + /* clear AEU */ + REG_WR(bp, + (BP_PORT(bp) ? MISC_REG_AEU_MASK_ATTN_FUNC_1 : + MISC_REG_AEU_MASK_ATTN_FUNC_0), 0); + msleep(10); + + /* save NIG port swap info */ + swap_val = REG_RD(bp, NIG_REG_PORT_SWAP); + swap_en = REG_RD(bp, NIG_REG_STRAP_OVERRIDE); /* reset device */ REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_CLEAR, - 0xd3ffff7f); + 0xd3ffffff); REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, 0x1403); + /* take the NIG out of reset and restore swap values */ + REG_WR(bp, + GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_SET, + MISC_REGISTERS_RESET_REG_1_RST_NIG); + REG_WR(bp, NIG_REG_PORT_SWAP, swap_val); + REG_WR(bp, NIG_REG_STRAP_OVERRIDE, swap_en); + + /* send unload done to the MCP */ + bnx2x_fw_command(bp, DRV_MSG_CODE_UNLOAD_DONE); + + /* restore our func and fw_seq */ + bp->func = func; + bp->fw_seq = + (SHMEM_RD(bp, func_mb[bp->func].drv_mb_header) & + DRV_MSG_SEQ_NUMBER_MASK); } + bnx2x_hw_unlock(bp, HW_LOCK_RESOURCE_UNDI); } } @@ -7384,6 +7407,9 @@ static int __devinit bnx2x_init_bp(struct bnx2x *bp) int func = BP_FUNC(bp); int rc; + /* Disable interrupt handling until HW is initialized */ + atomic_set(&bp->intr_sem, 1); + mutex_init(&bp->port.phy_mutex); INIT_WORK(&bp->sp_task, bnx2x_sp_task); @@ -9163,17 +9189,16 @@ static int bnx2x_poll(struct napi_struct *napi, int budget) bnx2x_update_fpsb_idx(fp); - if ((fp->tx_pkt_prod != le16_to_cpu(*fp->tx_cons_sb)) || - (fp->tx_pkt_prod != fp->tx_pkt_cons)) + if (BNX2X_HAS_TX_WORK(fp)) bnx2x_tx_int(fp, budget); - if (le16_to_cpu(*fp->rx_cons_sb) != fp->rx_comp_cons) + if (BNX2X_HAS_RX_WORK(fp)) work_done = bnx2x_rx_int(fp, budget); - rmb(); /* bnx2x_has_work() reads the status block */ + rmb(); /* BNX2X_HAS_WORK() reads the status block */ /* must not complete if we consumed full budget */ - if ((work_done < budget) && !bnx2x_has_work(fp)) { + if ((work_done < budget) && !BNX2X_HAS_WORK(fp)) { #ifdef BNX2X_STOP_ON_ERROR poll_panic: @@ -9408,7 +9433,7 @@ static int bnx2x_start_xmit(struct sk_buff *skb, struct net_device *dev) DP(NETIF_MSG_TX_QUEUED, "SKB linearization failed - " "silently dropping this SKB\n"); dev_kfree_skb_any(skb); - return 0; + return NETDEV_TX_OK; } } @@ -10200,7 +10225,7 @@ static int bnx2x_suspend(struct pci_dev *pdev, pm_message_t state) netif_device_detach(dev); - bnx2x_nic_unload(bp, UNLOAD_NORMAL); + bnx2x_nic_unload(bp, UNLOAD_CLOSE); bnx2x_set_power_state(bp, pci_choose_state(pdev, state)); @@ -10233,7 +10258,7 @@ static int bnx2x_resume(struct pci_dev *pdev) bnx2x_set_power_state(bp, PCI_D0); netif_device_attach(dev); - rc = bnx2x_nic_load(bp, LOAD_NORMAL); + rc = bnx2x_nic_load(bp, LOAD_OPEN); rtnl_unlock(); diff --git a/drivers/net/bnx2x_reg.h b/drivers/net/bnx2x_reg.h index 40c3a7735d2..b5313c209ca 100644 --- a/drivers/net/bnx2x_reg.h +++ b/drivers/net/bnx2x_reg.h @@ -1677,6 +1677,7 @@ /* [RW 8] init credit counter for port0 in LLH */ #define NIG_REG_LLH0_XCM_INIT_CREDIT 0x10554 #define NIG_REG_LLH0_XCM_MASK 0x10130 +#define NIG_REG_LLH1_BRB1_DRV_MASK 0x10248 /* [RW 1] send to BRB1 if no match on any of RMP rules. */ #define NIG_REG_LLH1_BRB1_NOT_MCP 0x102dc /* [RW 2] Determine the classification participants. 0: no classification.1: @@ -4962,6 +4963,7 @@ #define MISC_REGISTERS_GPIO_PORT_SHIFT 4 #define MISC_REGISTERS_GPIO_SET_POS 8 #define MISC_REGISTERS_RESET_REG_1_CLEAR 0x588 +#define MISC_REGISTERS_RESET_REG_1_RST_NIG (0x1<<7) #define MISC_REGISTERS_RESET_REG_1_SET 0x584 #define MISC_REGISTERS_RESET_REG_2_CLEAR 0x598 #define MISC_REGISTERS_RESET_REG_2_RST_BMAC0 (0x1<<0) @@ -4997,6 +4999,7 @@ #define HW_LOCK_RESOURCE_8072_MDIO 0 #define HW_LOCK_RESOURCE_GPIO 1 #define HW_LOCK_RESOURCE_SPIO 2 +#define HW_LOCK_RESOURCE_UNDI 5 #define AEU_INPUTS_ATTN_BITS_BRB_PARITY_ERROR (1<<18) #define AEU_INPUTS_ATTN_BITS_CCM_HW_INTERRUPT (1<<31) #define AEU_INPUTS_ATTN_BITS_CDU_HW_INTERRUPT (1<<9) -- GitLab From 4a37fb660c5505e0ee7ae16d80a06e85affe3055 Mon Sep 17 00:00:00 2001 From: Yitchak Gertner Date: Wed, 13 Aug 2008 15:50:23 -0700 Subject: [PATCH 249/750] bnx2x: HW lock mechanism HW lock mechanism Enhancing the HW lock to work per function and not only per port - this is needed for the next patch that protects races over HW attention detection between the different functions. At this chance, changing the functions names to be more inline with the current naming convention Signed-off-by: Yitchak Gertner Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x_main.c | 102 ++++++++++++++++++++++----------------- drivers/net/bnx2x_reg.h | 17 +++++++ 2 files changed, 75 insertions(+), 44 deletions(-) diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index dfa8c7b00cb..3e86ff4f4d4 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -1693,11 +1693,12 @@ static void bnx2x_stats_handle(struct bnx2x *bp, enum bnx2x_stats_event event); * General service functions */ -static int bnx2x_hw_lock(struct bnx2x *bp, u32 resource) +static int bnx2x_acquire_hw_lock(struct bnx2x *bp, u32 resource) { u32 lock_status; u32 resource_bit = (1 << resource); - u8 port = BP_PORT(bp); + int func = BP_FUNC(bp); + u32 hw_lock_control_reg; int cnt; /* Validating that the resource is within range */ @@ -1708,8 +1709,15 @@ static int bnx2x_hw_lock(struct bnx2x *bp, u32 resource) return -EINVAL; } + if (func <= 5) { + hw_lock_control_reg = (MISC_REG_DRIVER_CONTROL_1 + func*8); + } else { + hw_lock_control_reg = + (MISC_REG_DRIVER_CONTROL_7 + (func - 6)*8); + } + /* Validating that the resource is not already taken */ - lock_status = REG_RD(bp, MISC_REG_DRIVER_CONTROL_1 + port*8); + lock_status = REG_RD(bp, hw_lock_control_reg); if (lock_status & resource_bit) { DP(NETIF_MSG_HW, "lock_status 0x%x resource_bit 0x%x\n", lock_status, resource_bit); @@ -1719,9 +1727,8 @@ static int bnx2x_hw_lock(struct bnx2x *bp, u32 resource) /* Try for 1 second every 5ms */ for (cnt = 0; cnt < 200; cnt++) { /* Try to acquire the lock */ - REG_WR(bp, MISC_REG_DRIVER_CONTROL_1 + port*8 + 4, - resource_bit); - lock_status = REG_RD(bp, MISC_REG_DRIVER_CONTROL_1 + port*8); + REG_WR(bp, hw_lock_control_reg + 4, resource_bit); + lock_status = REG_RD(bp, hw_lock_control_reg); if (lock_status & resource_bit) return 0; @@ -1731,11 +1738,12 @@ static int bnx2x_hw_lock(struct bnx2x *bp, u32 resource) return -EAGAIN; } -static int bnx2x_hw_unlock(struct bnx2x *bp, u32 resource) +static int bnx2x_release_hw_lock(struct bnx2x *bp, u32 resource) { u32 lock_status; u32 resource_bit = (1 << resource); - u8 port = BP_PORT(bp); + int func = BP_FUNC(bp); + u32 hw_lock_control_reg; /* Validating that the resource is within range */ if (resource > HW_LOCK_MAX_RESOURCE_VALUE) { @@ -1745,20 +1753,27 @@ static int bnx2x_hw_unlock(struct bnx2x *bp, u32 resource) return -EINVAL; } + if (func <= 5) { + hw_lock_control_reg = (MISC_REG_DRIVER_CONTROL_1 + func*8); + } else { + hw_lock_control_reg = + (MISC_REG_DRIVER_CONTROL_7 + (func - 6)*8); + } + /* Validating that the resource is currently taken */ - lock_status = REG_RD(bp, MISC_REG_DRIVER_CONTROL_1 + port*8); + lock_status = REG_RD(bp, hw_lock_control_reg); if (!(lock_status & resource_bit)) { DP(NETIF_MSG_HW, "lock_status 0x%x resource_bit 0x%x\n", lock_status, resource_bit); return -EFAULT; } - REG_WR(bp, MISC_REG_DRIVER_CONTROL_1 + port*8, resource_bit); + REG_WR(bp, hw_lock_control_reg, resource_bit); return 0; } /* HW Lock for shared dual port PHYs */ -static void bnx2x_phy_hw_lock(struct bnx2x *bp) +static void bnx2x_acquire_phy_lock(struct bnx2x *bp) { u32 ext_phy_type = XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config); @@ -1766,16 +1781,16 @@ static void bnx2x_phy_hw_lock(struct bnx2x *bp) if ((ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072) || (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073)) - bnx2x_hw_lock(bp, HW_LOCK_RESOURCE_8072_MDIO); + bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_8072_MDIO); } -static void bnx2x_phy_hw_unlock(struct bnx2x *bp) +static void bnx2x_release_phy_lock(struct bnx2x *bp) { u32 ext_phy_type = XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config); if ((ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072) || (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073)) - bnx2x_hw_unlock(bp, HW_LOCK_RESOURCE_8072_MDIO); + bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_8072_MDIO); mutex_unlock(&bp->port.phy_mutex); } @@ -1795,7 +1810,7 @@ int bnx2x_set_gpio(struct bnx2x *bp, int gpio_num, u32 mode) return -EINVAL; } - bnx2x_hw_lock(bp, HW_LOCK_RESOURCE_GPIO); + bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_GPIO); /* read GPIO and mask except the float bits */ gpio_reg = (REG_RD(bp, MISC_REG_GPIO) & MISC_REGISTERS_GPIO_FLOAT); @@ -1828,7 +1843,7 @@ int bnx2x_set_gpio(struct bnx2x *bp, int gpio_num, u32 mode) } REG_WR(bp, MISC_REG_GPIO, gpio_reg); - bnx2x_hw_unlock(bp, HW_LOCK_RESOURCE_GPIO); + bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_GPIO); return 0; } @@ -1844,7 +1859,7 @@ static int bnx2x_set_spio(struct bnx2x *bp, int spio_num, u32 mode) return -EINVAL; } - bnx2x_hw_lock(bp, HW_LOCK_RESOURCE_SPIO); + bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_SPIO); /* read SPIO and mask except the float bits */ spio_reg = (REG_RD(bp, MISC_REG_SPIO) & MISC_REGISTERS_SPIO_FLOAT); @@ -1874,7 +1889,7 @@ static int bnx2x_set_spio(struct bnx2x *bp, int spio_num, u32 mode) } REG_WR(bp, MISC_REG_SPIO, spio_reg); - bnx2x_hw_unlock(bp, HW_LOCK_RESOURCE_SPIO); + bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_SPIO); return 0; } @@ -1940,9 +1955,9 @@ static u8 bnx2x_initial_phy_init(struct bnx2x *bp) /* Initialize link parameters structure variables */ bp->link_params.mtu = bp->dev->mtu; - bnx2x_phy_hw_lock(bp); + bnx2x_acquire_phy_lock(bp); rc = bnx2x_phy_init(&bp->link_params, &bp->link_vars); - bnx2x_phy_hw_unlock(bp); + bnx2x_release_phy_lock(bp); if (bp->link_vars.link_up) bnx2x_link_report(bp); @@ -1958,9 +1973,9 @@ static u8 bnx2x_initial_phy_init(struct bnx2x *bp) static void bnx2x_link_set(struct bnx2x *bp) { if (!BP_NOMCP(bp)) { - bnx2x_phy_hw_lock(bp); + bnx2x_acquire_phy_lock(bp); bnx2x_phy_init(&bp->link_params, &bp->link_vars); - bnx2x_phy_hw_unlock(bp); + bnx2x_release_phy_lock(bp); bnx2x_calc_fc_adv(bp); } else @@ -1970,9 +1985,9 @@ static void bnx2x_link_set(struct bnx2x *bp) static void bnx2x__link_reset(struct bnx2x *bp) { if (!BP_NOMCP(bp)) { - bnx2x_phy_hw_lock(bp); + bnx2x_acquire_phy_lock(bp); bnx2x_link_reset(&bp->link_params, &bp->link_vars); - bnx2x_phy_hw_unlock(bp); + bnx2x_release_phy_lock(bp); } else BNX2X_ERR("Bootcode is missing -not resetting link\n"); } @@ -1981,9 +1996,9 @@ static u8 bnx2x_link_test(struct bnx2x *bp) { u8 rc; - bnx2x_phy_hw_lock(bp); + bnx2x_acquire_phy_lock(bp); rc = bnx2x_test_link(&bp->link_params, &bp->link_vars); - bnx2x_phy_hw_unlock(bp); + bnx2x_release_phy_lock(bp); return rc; } @@ -2207,9 +2222,9 @@ static void bnx2x_link_attn(struct bnx2x *bp) /* Make sure that we are synced with the current statistics */ bnx2x_stats_handle(bp, STATS_EVENT_STOP); - bnx2x_phy_hw_lock(bp); + bnx2x_acquire_phy_lock(bp); bnx2x_link_update(&bp->link_params, &bp->link_vars); - bnx2x_phy_hw_unlock(bp); + bnx2x_release_phy_lock(bp); if (bp->link_vars.link_up) { @@ -2361,7 +2376,7 @@ static int bnx2x_sp_post(struct bnx2x *bp, int command, int cid, } /* acquire split MCP access lock register */ -static int bnx2x_lock_alr(struct bnx2x *bp) +static int bnx2x_acquire_alr(struct bnx2x *bp) { u32 i, j, val; int rc = 0; @@ -2385,8 +2400,8 @@ static int bnx2x_lock_alr(struct bnx2x *bp) return rc; } -/* Release split MCP access lock register */ -static void bnx2x_unlock_alr(struct bnx2x *bp) +/* release split MCP access lock register */ +static void bnx2x_release_alr(struct bnx2x *bp) { u32 val = 0; @@ -2399,7 +2414,6 @@ static inline u16 bnx2x_update_dsb_idx(struct bnx2x *bp) u16 rc = 0; barrier(); /* status block is written to by the chip */ - if (bp->def_att_idx != def_sb->atten_status_block.attn_bits_index) { bp->def_att_idx = def_sb->atten_status_block.attn_bits_index; rc |= 1; @@ -2706,7 +2720,7 @@ static void bnx2x_attn_int_deasserted(struct bnx2x *bp, u32 deasserted) /* need to take HW lock because MCP or other port might also try to handle this event */ - bnx2x_lock_alr(bp); + bnx2x_acquire_alr(bp); attn.sig[0] = REG_RD(bp, MISC_REG_AEU_AFTER_INVERT_1_FUNC_0 + port*4); attn.sig[1] = REG_RD(bp, MISC_REG_AEU_AFTER_INVERT_2_FUNC_0 + port*4); @@ -2742,7 +2756,7 @@ static void bnx2x_attn_int_deasserted(struct bnx2x *bp, u32 deasserted) } } - bnx2x_unlock_alr(bp); + bnx2x_release_alr(bp); reg_addr = (IGU_ADDR_ATTN_BITS_CLR + IGU_FUNC_BASE * BP_FUNC(bp)) * 8; @@ -6767,7 +6781,7 @@ static void __devinit bnx2x_undi_unload(struct bnx2x *bp) /* Check if it is the UNDI driver * UNDI driver initializes CID offset for normal bell to 0x7 */ - bnx2x_hw_lock(bp, HW_LOCK_RESOURCE_UNDI); + bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_UNDI); val = REG_RD(bp, DORQ_REG_NORM_CID_OFST); if (val == 0x7) { u32 reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS; @@ -6846,7 +6860,7 @@ static void __devinit bnx2x_undi_unload(struct bnx2x *bp) (SHMEM_RD(bp, func_mb[bp->func].drv_mb_header) & DRV_MSG_SEQ_NUMBER_MASK); } - bnx2x_hw_unlock(bp, HW_LOCK_RESOURCE_UNDI); + bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_UNDI); } } @@ -7703,11 +7717,11 @@ static void bnx2x_get_drvinfo(struct net_device *dev, phy_fw_ver[0] = '\0'; if (bp->port.pmf) { - bnx2x_phy_hw_lock(bp); + bnx2x_acquire_phy_lock(bp); bnx2x_get_ext_phy_fw_version(&bp->link_params, (bp->state != BNX2X_STATE_CLOSED), phy_fw_ver, PHY_FW_VER_LEN); - bnx2x_phy_hw_unlock(bp); + bnx2x_release_phy_lock(bp); } snprintf(info->fw_version, 32, "%d.%d.%d:%d BC:%x%s%s", @@ -8165,7 +8179,7 @@ static int bnx2x_set_eeprom(struct net_device *dev, if (eeprom->magic == 0x00504859) if (bp->port.pmf) { - bnx2x_phy_hw_lock(bp); + bnx2x_acquire_phy_lock(bp); rc = bnx2x_flash_download(bp, BP_PORT(bp), bp->link_params.ext_phy_config, (bp->state != BNX2X_STATE_CLOSED), @@ -8177,7 +8191,7 @@ static int bnx2x_set_eeprom(struct net_device *dev, rc |= bnx2x_phy_init(&bp->link_params, &bp->link_vars); } - bnx2x_phy_hw_unlock(bp); + bnx2x_release_phy_lock(bp); } else /* Only the PMF can access the PHY */ return -EINVAL; @@ -8601,15 +8615,15 @@ static int bnx2x_run_loopback(struct bnx2x *bp, int loopback_mode, u8 link_up) if (loopback_mode == BNX2X_MAC_LOOPBACK) { bp->link_params.loopback_mode = LOOPBACK_BMAC; - bnx2x_phy_hw_lock(bp); + bnx2x_acquire_phy_lock(bp); bnx2x_phy_init(&bp->link_params, &bp->link_vars); - bnx2x_phy_hw_unlock(bp); + bnx2x_release_phy_lock(bp); } else if (loopback_mode == BNX2X_PHY_LOOPBACK) { bp->link_params.loopback_mode = LOOPBACK_XGXS_10; - bnx2x_phy_hw_lock(bp); + bnx2x_acquire_phy_lock(bp); bnx2x_phy_init(&bp->link_params, &bp->link_vars); - bnx2x_phy_hw_unlock(bp); + bnx2x_release_phy_lock(bp); /* wait until link state is restored */ bnx2x_wait_for_link(bp, link_up); diff --git a/drivers/net/bnx2x_reg.h b/drivers/net/bnx2x_reg.h index b5313c209ca..3f65dffb6d7 100644 --- a/drivers/net/bnx2x_reg.h +++ b/drivers/net/bnx2x_reg.h @@ -1372,6 +1372,23 @@ be asserted). */ #define MISC_REG_DRIVER_CONTROL_16 0xa5f0 #define MISC_REG_DRIVER_CONTROL_16_SIZE 2 +/* [RW 32] The following driver registers(1...16) represent 16 drivers and + 32 clients. Each client can be controlled by one driver only. One in each + bit represent that this driver control the appropriate client (Ex: bit 5 + is set means this driver control client number 5). addr1 = set; addr0 = + clear; read from both addresses will give the same result = status. write + to address 1 will set a request to control all the clients that their + appropriate bit (in the write command) is set. if the client is free (the + appropriate bit in all the other drivers is clear) one will be written to + that driver register; if the client isn't free the bit will remain zero. + if the appropriate bit is set (the driver request to gain control on a + client it already controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW + interrupt will be asserted). write to address 0 will set a request to + free all the clients that their appropriate bit (in the write command) is + set. if the appropriate bit is clear (the driver request to free a client + it doesn't controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW interrupt will + be asserted). */ +#define MISC_REG_DRIVER_CONTROL_7 0xa3c8 /* [RW 1] e1hmf for WOL. If clr WOL signal o the PXP will be send on bit 0 only. */ #define MISC_REG_E1HMF_MODE 0xa5f8 -- GitLab From 3fcaf2e566b9cf8ccd16bcda3440717236de163d Mon Sep 17 00:00:00 2001 From: Eilon Greenstein Date: Wed, 13 Aug 2008 15:50:45 -0700 Subject: [PATCH 250/750] bnx2x: HW attention lock HW attention lock Making sure that only one function will handle the HW attention. This makes the device parameter aeu_mask redundant so it is removed Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x.h | 1 - drivers/net/bnx2x_main.c | 42 +++++++++++++++++++++++----------------- drivers/net/bnx2x_reg.h | 1 + 3 files changed, 25 insertions(+), 19 deletions(-) diff --git a/drivers/net/bnx2x.h b/drivers/net/bnx2x.h index b9aa6f48ae2..3b09ae62335 100644 --- a/drivers/net/bnx2x.h +++ b/drivers/net/bnx2x.h @@ -774,7 +774,6 @@ struct bnx2x { u16 def_att_idx; u32 attn_state; struct attn_route attn_group[MAX_DYNAMIC_ATTN_GRPS]; - u32 aeu_mask; u32 nig_mask; /* slow path ring */ diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index 3e86ff4f4d4..c8b61788abb 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -2450,20 +2450,25 @@ static void bnx2x_attn_int_asserted(struct bnx2x *bp, u32 asserted) MISC_REG_AEU_MASK_ATTN_FUNC_0; u32 nig_int_mask_addr = port ? NIG_REG_MASK_INTERRUPT_PORT1 : NIG_REG_MASK_INTERRUPT_PORT0; + u32 aeu_mask; - if (~bp->aeu_mask & (asserted & 0xff)) - BNX2X_ERR("IGU ERROR\n"); if (bp->attn_state & asserted) BNX2X_ERR("IGU ERROR\n"); + bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_PORT0_ATT_MASK + port); + aeu_mask = REG_RD(bp, aeu_addr); + DP(NETIF_MSG_HW, "aeu_mask %x newly asserted %x\n", - bp->aeu_mask, asserted); - bp->aeu_mask &= ~(asserted & 0xff); - DP(NETIF_MSG_HW, "after masking: aeu_mask %x\n", bp->aeu_mask); + aeu_mask, asserted); + aeu_mask &= ~(asserted & 0xff); + DP(NETIF_MSG_HW, "new mask %x\n", aeu_mask); - REG_WR(bp, aeu_addr, bp->aeu_mask); + REG_WR(bp, aeu_addr, aeu_mask); + bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_PORT0_ATT_MASK + port); + DP(NETIF_MSG_HW, "attn_state %x\n", bp->attn_state); bp->attn_state |= asserted; + DP(NETIF_MSG_HW, "new state %x\n", bp->attn_state); if (asserted & ATTN_HARD_WIRED_MASK) { if (asserted & ATTN_NIG_FOR_FUNC) { @@ -2717,6 +2722,7 @@ static void bnx2x_attn_int_deasserted(struct bnx2x *bp, u32 deasserted) int index; u32 reg_addr; u32 val; + u32 aeu_mask; /* need to take HW lock because MCP or other port might also try to handle this event */ @@ -2761,23 +2767,26 @@ static void bnx2x_attn_int_deasserted(struct bnx2x *bp, u32 deasserted) reg_addr = (IGU_ADDR_ATTN_BITS_CLR + IGU_FUNC_BASE * BP_FUNC(bp)) * 8; val = ~deasserted; -/* DP(NETIF_MSG_INTR, "write 0x%08x to IGU addr 0x%x\n", - val, BAR_IGU_INTMEM + reg_addr); */ + DP(NETIF_MSG_HW, "about to mask 0x%08x at HC addr 0x%x\n", + val, reg_addr); REG_WR(bp, BAR_IGU_INTMEM + reg_addr, val); - if (bp->aeu_mask & (deasserted & 0xff)) - BNX2X_ERR("IGU BUG!\n"); if (~bp->attn_state & deasserted) - BNX2X_ERR("IGU BUG!\n"); + BNX2X_ERR("IGU ERROR\n"); reg_addr = port ? MISC_REG_AEU_MASK_ATTN_FUNC_1 : MISC_REG_AEU_MASK_ATTN_FUNC_0; - DP(NETIF_MSG_HW, "aeu_mask %x\n", bp->aeu_mask); - bp->aeu_mask |= (deasserted & 0xff); + bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_PORT0_ATT_MASK + port); + aeu_mask = REG_RD(bp, reg_addr); + + DP(NETIF_MSG_HW, "aeu_mask %x newly deasserted %x\n", + aeu_mask, deasserted); + aeu_mask |= (deasserted & 0xff); + DP(NETIF_MSG_HW, "new mask %x\n", aeu_mask); - DP(NETIF_MSG_HW, "new mask %x\n", bp->aeu_mask); - REG_WR(bp, reg_addr, bp->aeu_mask); + REG_WR(bp, reg_addr, aeu_mask); + bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_PORT0_ATT_MASK + port); DP(NETIF_MSG_HW, "attn_state %x\n", bp->attn_state); bp->attn_state &= ~deasserted; @@ -4083,9 +4092,6 @@ static void bnx2x_init_def_sb(struct bnx2x *bp, reg_offset + 0xc + 0x10*index); } - bp->aeu_mask = REG_RD(bp, (port ? MISC_REG_AEU_MASK_ATTN_FUNC_1 : - MISC_REG_AEU_MASK_ATTN_FUNC_0)); - reg_offset = (port ? HC_REG_ATTN_MSG1_ADDR_L : HC_REG_ATTN_MSG0_ADDR_L); diff --git a/drivers/net/bnx2x_reg.h b/drivers/net/bnx2x_reg.h index 3f65dffb6d7..f72ffd29e37 100644 --- a/drivers/net/bnx2x_reg.h +++ b/drivers/net/bnx2x_reg.h @@ -5015,6 +5015,7 @@ #define HW_LOCK_MAX_RESOURCE_VALUE 31 #define HW_LOCK_RESOURCE_8072_MDIO 0 #define HW_LOCK_RESOURCE_GPIO 1 +#define HW_LOCK_RESOURCE_PORT0_ATT_MASK 3 #define HW_LOCK_RESOURCE_SPIO 2 #define HW_LOCK_RESOURCE_UNDI 5 #define AEU_INPUTS_ATTN_BITS_BRB_PARITY_ERROR (1<<18) -- GitLab From 326262307bad2391a6393bb1968ed9a9a16fc617 Mon Sep 17 00:00:00 2001 From: Eilon Greenstein Date: Wed, 13 Aug 2008 15:51:07 -0700 Subject: [PATCH 251/750] bnx2x: Memory allocation Memory allocation - The CQE ring was allocated to the max size even for a chip that does not support it. Fixed to allocate according to the chip type to save memory - The rx_page_ring was not freed on driver unload Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x_main.c | 15 +++++++++------ 1 file changed, 9 insertions(+), 6 deletions(-) diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index c8b61788abb..b8cdce21c5d 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -4252,7 +4252,9 @@ static inline void bnx2x_free_tpa_pool(struct bnx2x *bp, static void bnx2x_init_rx_rings(struct bnx2x *bp) { int func = BP_FUNC(bp); - u16 ring_prod, cqe_ring_prod = 0; + int max_agg_queues = CHIP_IS_E1(bp) ? ETH_MAX_AGGREGATION_QUEUES_E1 : + ETH_MAX_AGGREGATION_QUEUES_E1H; + u16 ring_prod, cqe_ring_prod; int i, j; bp->rx_buf_use_size = bp->dev->mtu; @@ -4266,9 +4268,9 @@ static void bnx2x_init_rx_rings(struct bnx2x *bp) bp->dev->mtu + ETH_OVREHEAD); for_each_queue(bp, j) { - for (i = 0; i < ETH_MAX_AGGREGATION_QUEUES_E1H; i++) { - struct bnx2x_fastpath *fp = &bp->fp[j]; + struct bnx2x_fastpath *fp = &bp->fp[j]; + for (i = 0; i < max_agg_queues; i++) { fp->tpa_pool[i].skb = netdev_alloc_skb(bp->dev, bp->rx_buf_size); if (!fp->tpa_pool[i].skb) { @@ -4348,8 +4350,7 @@ static void bnx2x_init_rx_rings(struct bnx2x *bp) BNX2X_ERR("disabling TPA for queue[%d]\n", j); /* Cleanup already allocated elements */ bnx2x_free_rx_sge_range(bp, fp, ring_prod); - bnx2x_free_tpa_pool(bp, fp, - ETH_MAX_AGGREGATION_QUEUES_E1H); + bnx2x_free_tpa_pool(bp, fp, max_agg_queues); fp->disable_tpa = 1; ring_prod = 0; break; @@ -5772,6 +5773,7 @@ static void bnx2x_free_mem(struct bnx2x *bp) NUM_RCQ_BD); /* SGE ring */ + BNX2X_FREE(bnx2x_fp(bp, i, rx_page_ring)); BNX2X_PCI_FREE(bnx2x_fp(bp, i, rx_sge_ring), bnx2x_fp(bp, i, rx_sge_mapping), BCM_PAGE_SIZE * NUM_RX_SGE_PAGES); @@ -5949,7 +5951,8 @@ static void bnx2x_free_rx_skbs(struct bnx2x *bp) dev_kfree_skb(skb); } if (!fp->disable_tpa) - bnx2x_free_tpa_pool(bp, fp, + bnx2x_free_tpa_pool(bp, fp, CHIP_IS_E1(bp) ? + ETH_MAX_AGGREGATION_QUEUES_E1 : ETH_MAX_AGGREGATION_QUEUES_E1H); } } -- GitLab From 9dabc4242f7e51d98a71af7ee11a36e637897f9e Mon Sep 17 00:00:00 2001 From: Yitchak Gertner Date: Wed, 13 Aug 2008 15:51:28 -0700 Subject: [PATCH 252/750] bnx2x: Self-test false positive Self-test false positive - The memory test should use a mask according to the chip type - In the register test, check the port only once and not inside the for loop (not causing a failure - just ugly) Signed-off-by: Yitchak Gertner Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x_main.c | 24 +++++++++++++----------- 1 file changed, 13 insertions(+), 11 deletions(-) diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index b8cdce21c5d..a4177e964c5 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -8420,6 +8420,7 @@ static int bnx2x_test_registers(struct bnx2x *bp) { int idx, i, rc = -ENODEV; u32 wr_val = 0; + int port = BP_PORT(bp); static const struct { u32 offset0; u32 offset1; @@ -8485,7 +8486,6 @@ static int bnx2x_test_registers(struct bnx2x *bp) for (i = 0; reg_tbl[i].offset0 != 0xffffffff; i++) { u32 offset, mask, save_val, val; - int port = BP_PORT(bp); offset = reg_tbl[i].offset0 + port*reg_tbl[i].offset1; mask = reg_tbl[i].mask; @@ -8531,16 +8531,17 @@ static int bnx2x_test_memory(struct bnx2x *bp) static const struct { char *name; u32 offset; - u32 mask; + u32 e1_mask; + u32 e1h_mask; } prty_tbl[] = { - { "CCM_REG_CCM_PRTY_STS", CCM_REG_CCM_PRTY_STS, 0 }, - { "CFC_REG_CFC_PRTY_STS", CFC_REG_CFC_PRTY_STS, 0 }, - { "DMAE_REG_DMAE_PRTY_STS", DMAE_REG_DMAE_PRTY_STS, 0 }, - { "TCM_REG_TCM_PRTY_STS", TCM_REG_TCM_PRTY_STS, 0 }, - { "UCM_REG_UCM_PRTY_STS", UCM_REG_UCM_PRTY_STS, 0 }, - { "XCM_REG_XCM_PRTY_STS", XCM_REG_XCM_PRTY_STS, 0x1 }, - - { NULL, 0xffffffff, 0 } + { "CCM_PRTY_STS", CCM_REG_CCM_PRTY_STS, 0x3ffc0, 0 }, + { "CFC_PRTY_STS", CFC_REG_CFC_PRTY_STS, 0x2, 0x2 }, + { "DMAE_PRTY_STS", DMAE_REG_DMAE_PRTY_STS, 0, 0 }, + { "TCM_PRTY_STS", TCM_REG_TCM_PRTY_STS, 0x3ffc0, 0 }, + { "UCM_PRTY_STS", UCM_REG_UCM_PRTY_STS, 0x3ffc0, 0 }, + { "XCM_PRTY_STS", XCM_REG_XCM_PRTY_STS, 0x3ffc1, 0 }, + + { NULL, 0xffffffff, 0, 0 } }; if (!netif_running(bp->dev)) @@ -8554,7 +8555,8 @@ static int bnx2x_test_memory(struct bnx2x *bp) /* Check the parity status */ for (i = 0; prty_tbl[i].offset != 0xffffffff; i++) { val = REG_RD(bp, prty_tbl[i].offset); - if (val & ~(prty_tbl[i].mask)) { + if ((CHIP_IS_E1(bp) && (val & ~(prty_tbl[i].e1_mask))) || + (CHIP_IS_E1H(bp) && (val & ~(prty_tbl[i].e1h_mask)))) { DP(NETIF_MSG_HW, "%s is 0x%x\n", prty_tbl[i].name, val); goto test_mem_exit; -- GitLab From 5c862848172846a7aa88d0a564eb8998ecac2f0d Mon Sep 17 00:00:00 2001 From: Eilon Greenstein Date: Wed, 13 Aug 2008 15:51:48 -0700 Subject: [PATCH 253/750] bnx2x: PBA Table Page Alignment Workaround PBA Table Page Alignment Workaround The PBA table starts on the middle of the page and that's causing very low performance with virtualization. The solution is not to update via the BAR directly but via chip access to the same memory Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x_main.c | 92 +++++++++------------- drivers/net/bnx2x_reg.h | 162 ++++++++++++++++++++++----------------- 2 files changed, 130 insertions(+), 124 deletions(-) diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index a4177e964c5..b2886db5704 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -685,7 +685,8 @@ static void bnx2x_int_disable_sync(struct bnx2x *bp) static inline void bnx2x_ack_sb(struct bnx2x *bp, u8 sb_id, u8 storm, u16 index, u8 op, u8 update) { - u32 igu_addr = (IGU_ADDR_INT_ACK + IGU_FUNC_BASE * BP_FUNC(bp)) * 8; + u32 hc_addr = (HC_REG_COMMAND_REG + BP_PORT(bp)*32 + + COMMAND_REG_INT_ACK); struct igu_ack_register igu_ack; igu_ack.status_block_index = index; @@ -695,9 +696,9 @@ static inline void bnx2x_ack_sb(struct bnx2x *bp, u8 sb_id, (update << IGU_ACK_REGISTER_UPDATE_INDEX_SHIFT) | (op << IGU_ACK_REGISTER_INTERRUPT_MODE_SHIFT)); - DP(BNX2X_MSG_OFF, "write 0x%08x to IGU addr 0x%x\n", - (*(u32 *)&igu_ack), BAR_IGU_INTMEM + igu_addr); - REG_WR(bp, BAR_IGU_INTMEM + igu_addr, (*(u32 *)&igu_ack)); + DP(BNX2X_MSG_OFF, "write 0x%08x to HC addr 0x%x\n", + (*(u32 *)&igu_ack), hc_addr); + REG_WR(bp, hc_addr, (*(u32 *)&igu_ack)); } static inline u16 bnx2x_update_fpsb_idx(struct bnx2x_fastpath *fp) @@ -719,19 +720,13 @@ static inline u16 bnx2x_update_fpsb_idx(struct bnx2x_fastpath *fp) static u16 bnx2x_ack_int(struct bnx2x *bp) { - u32 igu_addr = (IGU_ADDR_SIMD_MASK + IGU_FUNC_BASE * BP_FUNC(bp)) * 8; - u32 result = REG_RD(bp, BAR_IGU_INTMEM + igu_addr); + u32 hc_addr = (HC_REG_COMMAND_REG + BP_PORT(bp)*32 + + COMMAND_REG_SIMD_MASK); + u32 result = REG_RD(bp, hc_addr); - DP(BNX2X_MSG_OFF, "read 0x%08x from IGU addr 0x%x\n", - result, BAR_IGU_INTMEM + igu_addr); + DP(BNX2X_MSG_OFF, "read 0x%08x from HC addr 0x%x\n", + result, hc_addr); -#ifdef IGU_DEBUG -#warning IGU_DEBUG active - if (result == 0) { - BNX2X_ERR("read %x from IGU\n", result); - REG_WR(bp, TM_REG_TIMER_SOFT_RST, 0); - } -#endif return result; } @@ -2444,8 +2439,8 @@ static inline u16 bnx2x_update_dsb_idx(struct bnx2x *bp) static void bnx2x_attn_int_asserted(struct bnx2x *bp, u32 asserted) { int port = BP_PORT(bp); - int func = BP_FUNC(bp); - u32 igu_addr = (IGU_ADDR_ATTN_BITS_SET + IGU_FUNC_BASE * func) * 8; + u32 hc_addr = (HC_REG_COMMAND_REG + port*32 + + COMMAND_REG_ATTN_BITS_SET); u32 aeu_addr = port ? MISC_REG_AEU_MASK_ATTN_FUNC_1 : MISC_REG_AEU_MASK_ATTN_FUNC_0; u32 nig_int_mask_addr = port ? NIG_REG_MASK_INTERRUPT_PORT1 : @@ -2523,9 +2518,9 @@ static void bnx2x_attn_int_asserted(struct bnx2x *bp, u32 asserted) } /* if hardwired */ - DP(NETIF_MSG_HW, "about to mask 0x%08x at IGU addr 0x%x\n", - asserted, BAR_IGU_INTMEM + igu_addr); - REG_WR(bp, BAR_IGU_INTMEM + igu_addr, asserted); + DP(NETIF_MSG_HW, "about to mask 0x%08x at HC addr 0x%x\n", + asserted, hc_addr); + REG_WR(bp, hc_addr, asserted); /* now set back the mask */ if (asserted & ATTN_NIG_FOR_FUNC) @@ -2764,12 +2759,12 @@ static void bnx2x_attn_int_deasserted(struct bnx2x *bp, u32 deasserted) bnx2x_release_alr(bp); - reg_addr = (IGU_ADDR_ATTN_BITS_CLR + IGU_FUNC_BASE * BP_FUNC(bp)) * 8; + reg_addr = (HC_REG_COMMAND_REG + port*32 + COMMAND_REG_ATTN_BITS_CLR); val = ~deasserted; DP(NETIF_MSG_HW, "about to mask 0x%08x at HC addr 0x%x\n", val, reg_addr); - REG_WR(bp, BAR_IGU_INTMEM + reg_addr, val); + REG_WR(bp, reg_addr, val); if (~bp->attn_state & deasserted) BNX2X_ERR("IGU ERROR\n"); @@ -3998,8 +3993,8 @@ static void bnx2x_zero_sb(struct bnx2x *bp, int sb_id) sizeof(struct cstorm_def_status_block)/4); } -static void bnx2x_init_sb(struct bnx2x *bp, int sb_id, - struct host_status_block *sb, dma_addr_t mapping) +static void bnx2x_init_sb(struct bnx2x *bp, struct host_status_block *sb, + dma_addr_t mapping, int sb_id) { int port = BP_PORT(bp); int func = BP_FUNC(bp); @@ -4075,7 +4070,6 @@ static void bnx2x_init_def_sb(struct bnx2x *bp, atten_status_block); def_sb->atten_status_block.status_block_id = sb_id; - bp->def_att_idx = 0; bp->attn_state = 0; reg_offset = (port ? MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0 : @@ -4109,17 +4103,13 @@ static void bnx2x_init_def_sb(struct bnx2x *bp, u_def_status_block); def_sb->u_def_status_block.status_block_id = sb_id; - bp->def_u_idx = 0; - REG_WR(bp, BAR_USTRORM_INTMEM + USTORM_DEF_SB_HOST_SB_ADDR_OFFSET(func), U64_LO(section)); REG_WR(bp, BAR_USTRORM_INTMEM + ((USTORM_DEF_SB_HOST_SB_ADDR_OFFSET(func)) + 4), U64_HI(section)); - REG_WR8(bp, BAR_USTRORM_INTMEM + DEF_USB_FUNC_OFF + + REG_WR8(bp, BAR_USTRORM_INTMEM + DEF_USB_FUNC_OFF + USTORM_DEF_SB_HOST_STATUS_BLOCK_OFFSET(func), func); - REG_WR(bp, BAR_USTRORM_INTMEM + USTORM_HC_BTR_OFFSET(func), - BNX2X_BTR); for (index = 0; index < HC_USTORM_DEF_SB_NUM_INDICES; index++) REG_WR16(bp, BAR_USTRORM_INTMEM + @@ -4130,17 +4120,13 @@ static void bnx2x_init_def_sb(struct bnx2x *bp, c_def_status_block); def_sb->c_def_status_block.status_block_id = sb_id; - bp->def_c_idx = 0; - REG_WR(bp, BAR_CSTRORM_INTMEM + CSTORM_DEF_SB_HOST_SB_ADDR_OFFSET(func), U64_LO(section)); REG_WR(bp, BAR_CSTRORM_INTMEM + ((CSTORM_DEF_SB_HOST_SB_ADDR_OFFSET(func)) + 4), U64_HI(section)); - REG_WR8(bp, BAR_CSTRORM_INTMEM + DEF_CSB_FUNC_OFF + + REG_WR8(bp, BAR_CSTRORM_INTMEM + DEF_CSB_FUNC_OFF + CSTORM_DEF_SB_HOST_STATUS_BLOCK_OFFSET(func), func); - REG_WR(bp, BAR_CSTRORM_INTMEM + CSTORM_HC_BTR_OFFSET(func), - BNX2X_BTR); for (index = 0; index < HC_CSTORM_DEF_SB_NUM_INDICES; index++) REG_WR16(bp, BAR_CSTRORM_INTMEM + @@ -4151,17 +4137,13 @@ static void bnx2x_init_def_sb(struct bnx2x *bp, t_def_status_block); def_sb->t_def_status_block.status_block_id = sb_id; - bp->def_t_idx = 0; - REG_WR(bp, BAR_TSTRORM_INTMEM + TSTORM_DEF_SB_HOST_SB_ADDR_OFFSET(func), U64_LO(section)); REG_WR(bp, BAR_TSTRORM_INTMEM + ((TSTORM_DEF_SB_HOST_SB_ADDR_OFFSET(func)) + 4), U64_HI(section)); - REG_WR8(bp, BAR_TSTRORM_INTMEM + DEF_TSB_FUNC_OFF + + REG_WR8(bp, BAR_TSTRORM_INTMEM + DEF_TSB_FUNC_OFF + TSTORM_DEF_SB_HOST_STATUS_BLOCK_OFFSET(func), func); - REG_WR(bp, BAR_TSTRORM_INTMEM + TSTORM_HC_BTR_OFFSET(func), - BNX2X_BTR); for (index = 0; index < HC_TSTORM_DEF_SB_NUM_INDICES; index++) REG_WR16(bp, BAR_TSTRORM_INTMEM + @@ -4172,17 +4154,13 @@ static void bnx2x_init_def_sb(struct bnx2x *bp, x_def_status_block); def_sb->x_def_status_block.status_block_id = sb_id; - bp->def_x_idx = 0; - REG_WR(bp, BAR_XSTRORM_INTMEM + XSTORM_DEF_SB_HOST_SB_ADDR_OFFSET(func), U64_LO(section)); REG_WR(bp, BAR_XSTRORM_INTMEM + ((XSTORM_DEF_SB_HOST_SB_ADDR_OFFSET(func)) + 4), U64_HI(section)); - REG_WR8(bp, BAR_XSTRORM_INTMEM + DEF_XSB_FUNC_OFF + + REG_WR8(bp, BAR_XSTRORM_INTMEM + DEF_XSB_FUNC_OFF + XSTORM_DEF_SB_HOST_STATUS_BLOCK_OFFSET(func), func); - REG_WR(bp, BAR_XSTRORM_INTMEM + XSTORM_HC_BTR_OFFSET(func), - BNX2X_BTR); for (index = 0; index < HC_XSTORM_DEF_SB_NUM_INDICES; index++) REG_WR16(bp, BAR_XSTRORM_INTMEM + @@ -4205,21 +4183,25 @@ static void bnx2x_update_coalesce(struct bnx2x *bp) /* HC_INDEX_U_ETH_RX_CQ_CONS */ REG_WR8(bp, BAR_USTRORM_INTMEM + USTORM_SB_HC_TIMEOUT_OFFSET(port, sb_id, - HC_INDEX_U_ETH_RX_CQ_CONS), + U_SB_ETH_RX_CQ_INDEX), bp->rx_ticks/12); REG_WR16(bp, BAR_USTRORM_INTMEM + USTORM_SB_HC_DISABLE_OFFSET(port, sb_id, - HC_INDEX_U_ETH_RX_CQ_CONS), + U_SB_ETH_RX_CQ_INDEX), + bp->rx_ticks ? 0 : 1); + REG_WR16(bp, BAR_USTRORM_INTMEM + + USTORM_SB_HC_DISABLE_OFFSET(port, sb_id, + U_SB_ETH_RX_BD_INDEX), bp->rx_ticks ? 0 : 1); /* HC_INDEX_C_ETH_TX_CQ_CONS */ REG_WR8(bp, BAR_CSTRORM_INTMEM + CSTORM_SB_HC_TIMEOUT_OFFSET(port, sb_id, - HC_INDEX_C_ETH_TX_CQ_CONS), + C_SB_ETH_TX_CQ_INDEX), bp->tx_ticks/12); REG_WR16(bp, BAR_CSTRORM_INTMEM + CSTORM_SB_HC_DISABLE_OFFSET(port, sb_id, - HC_INDEX_C_ETH_TX_CQ_CONS), + C_SB_ETH_TX_CQ_INDEX), bp->tx_ticks ? 0 : 1); } } @@ -4494,7 +4476,7 @@ static void bnx2x_init_context(struct bnx2x *bp) } context->cstorm_st_context.sb_index_number = - HC_INDEX_C_ETH_TX_CQ_CONS; + C_SB_ETH_TX_CQ_INDEX; context->cstorm_st_context.status_block_id = sb_id; context->xstorm_ag_context.cdu_reserved = @@ -4773,12 +4755,14 @@ static void bnx2x_nic_init(struct bnx2x *bp, u32 load_code) DP(NETIF_MSG_IFUP, "bnx2x_init_sb(%p,%p) index %d cl_id %d sb %d\n", bp, fp->status_blk, i, FP_CL_ID(fp), FP_SB_ID(fp)); - bnx2x_init_sb(bp, FP_SB_ID(fp), fp->status_blk, - fp->status_blk_mapping); + bnx2x_init_sb(bp, fp->status_blk, fp->status_blk_mapping, + FP_SB_ID(fp)); + bnx2x_update_fpsb_idx(fp); } - bnx2x_init_def_sb(bp, bp->def_status_blk, - bp->def_status_blk_mapping, DEF_SB_ID); + bnx2x_init_def_sb(bp, bp->def_status_blk, bp->def_status_blk_mapping, + DEF_SB_ID); + bnx2x_update_dsb_idx(bp); bnx2x_update_coalesce(bp); bnx2x_init_rx_rings(bp); bnx2x_init_tx_ring(bp); diff --git a/drivers/net/bnx2x_reg.h b/drivers/net/bnx2x_reg.h index f72ffd29e37..a85ff207368 100644 --- a/drivers/net/bnx2x_reg.h +++ b/drivers/net/bnx2x_reg.h @@ -740,6 +740,7 @@ #define HC_REG_ATTN_MSG1_ADDR_L 0x108020 #define HC_REG_ATTN_NUM_P0 0x108038 #define HC_REG_ATTN_NUM_P1 0x10803c +#define HC_REG_COMMAND_REG 0x108180 #define HC_REG_CONFIG_0 0x108000 #define HC_REG_CONFIG_1 0x108004 #define HC_REG_FUNC_NUM_P0 0x1080ac @@ -5168,59 +5169,73 @@ #define GRCBASE_MISC_AEU GRCBASE_MISC -/*the offset of the configuration space in the pci core register*/ +/* offset of configuration space in the pci core register */ #define PCICFG_OFFSET 0x2000 #define PCICFG_VENDOR_ID_OFFSET 0x00 #define PCICFG_DEVICE_ID_OFFSET 0x02 #define PCICFG_COMMAND_OFFSET 0x04 +#define PCICFG_COMMAND_IO_SPACE (1<<0) +#define PCICFG_COMMAND_MEM_SPACE (1<<1) +#define PCICFG_COMMAND_BUS_MASTER (1<<2) +#define PCICFG_COMMAND_SPECIAL_CYCLES (1<<3) +#define PCICFG_COMMAND_MWI_CYCLES (1<<4) +#define PCICFG_COMMAND_VGA_SNOOP (1<<5) +#define PCICFG_COMMAND_PERR_ENA (1<<6) +#define PCICFG_COMMAND_STEPPING (1<<7) +#define PCICFG_COMMAND_SERR_ENA (1<<8) +#define PCICFG_COMMAND_FAST_B2B (1<<9) +#define PCICFG_COMMAND_INT_DISABLE (1<<10) +#define PCICFG_COMMAND_RESERVED (0x1f<<11) #define PCICFG_STATUS_OFFSET 0x06 -#define PCICFG_REVESION_ID 0x08 +#define PCICFG_REVESION_ID 0x08 #define PCICFG_CACHE_LINE_SIZE 0x0c #define PCICFG_LATENCY_TIMER 0x0d -#define PCICFG_BAR_1_LOW 0x10 -#define PCICFG_BAR_1_HIGH 0x14 -#define PCICFG_BAR_2_LOW 0x18 -#define PCICFG_BAR_2_HIGH 0x1c -#define PCICFG_SUBSYSTEM_VENDOR_ID_OFFSET 0x2c +#define PCICFG_BAR_1_LOW 0x10 +#define PCICFG_BAR_1_HIGH 0x14 +#define PCICFG_BAR_2_LOW 0x18 +#define PCICFG_BAR_2_HIGH 0x1c +#define PCICFG_SUBSYSTEM_VENDOR_ID_OFFSET 0x2c #define PCICFG_SUBSYSTEM_ID_OFFSET 0x2e -#define PCICFG_INT_LINE 0x3c -#define PCICFG_INT_PIN 0x3d -#define PCICFG_PM_CSR_OFFSET 0x4c -#define PCICFG_GRC_ADDRESS 0x78 -#define PCICFG_GRC_DATA 0x80 +#define PCICFG_INT_LINE 0x3c +#define PCICFG_INT_PIN 0x3d +#define PCICFG_PM_CAPABILITY 0x48 +#define PCICFG_PM_CAPABILITY_VERSION (0x3<<16) +#define PCICFG_PM_CAPABILITY_CLOCK (1<<19) +#define PCICFG_PM_CAPABILITY_RESERVED (1<<20) +#define PCICFG_PM_CAPABILITY_DSI (1<<21) +#define PCICFG_PM_CAPABILITY_AUX_CURRENT (0x7<<22) +#define PCICFG_PM_CAPABILITY_D1_SUPPORT (1<<25) +#define PCICFG_PM_CAPABILITY_D2_SUPPORT (1<<26) +#define PCICFG_PM_CAPABILITY_PME_IN_D0 (1<<27) +#define PCICFG_PM_CAPABILITY_PME_IN_D1 (1<<28) +#define PCICFG_PM_CAPABILITY_PME_IN_D2 (1<<29) +#define PCICFG_PM_CAPABILITY_PME_IN_D3_HOT (1<<30) +#define PCICFG_PM_CAPABILITY_PME_IN_D3_COLD (1<<31) +#define PCICFG_PM_CSR_OFFSET 0x4c +#define PCICFG_PM_CSR_STATE (0x3<<0) +#define PCICFG_PM_CSR_PME_ENABLE (1<<8) +#define PCICFG_PM_CSR_PME_STATUS (1<<15) +#define PCICFG_GRC_ADDRESS 0x78 +#define PCICFG_GRC_DATA 0x80 #define PCICFG_DEVICE_CONTROL 0xb4 #define PCICFG_LINK_CONTROL 0xbc -#define PCICFG_COMMAND_IO_SPACE (1<<0) -#define PCICFG_COMMAND_MEM_SPACE (1<<1) -#define PCICFG_COMMAND_BUS_MASTER (1<<2) -#define PCICFG_COMMAND_SPECIAL_CYCLES (1<<3) -#define PCICFG_COMMAND_MWI_CYCLES (1<<4) -#define PCICFG_COMMAND_VGA_SNOOP (1<<5) -#define PCICFG_COMMAND_PERR_ENA (1<<6) -#define PCICFG_COMMAND_STEPPING (1<<7) -#define PCICFG_COMMAND_SERR_ENA (1<<8) -#define PCICFG_COMMAND_FAST_B2B (1<<9) -#define PCICFG_COMMAND_INT_DISABLE (1<<10) -#define PCICFG_COMMAND_RESERVED (0x1f<<11) - -#define PCICFG_PM_CSR_STATE (0x3<<0) -#define PCICFG_PM_CSR_PME_STATUS (1<<15) #define BAR_USTRORM_INTMEM 0x400000 #define BAR_CSTRORM_INTMEM 0x410000 #define BAR_XSTRORM_INTMEM 0x420000 #define BAR_TSTRORM_INTMEM 0x430000 +/* for accessing the IGU in case of status block ACK */ #define BAR_IGU_INTMEM 0x440000 #define BAR_DOORBELL_OFFSET 0x800000 #define BAR_ME_REGISTER 0x450000 - -#define GRC_CONFIG_2_SIZE_REG 0x408 /* config_2 offset */ -#define PCI_CONFIG_2_BAR1_SIZE (0xfL<<0) +/* config_2 offset */ +#define GRC_CONFIG_2_SIZE_REG 0x408 +#define PCI_CONFIG_2_BAR1_SIZE (0xfL<<0) #define PCI_CONFIG_2_BAR1_SIZE_DISABLED (0L<<0) #define PCI_CONFIG_2_BAR1_SIZE_64K (1L<<0) #define PCI_CONFIG_2_BAR1_SIZE_128K (2L<<0) @@ -5237,11 +5252,11 @@ #define PCI_CONFIG_2_BAR1_SIZE_256M (13L<<0) #define PCI_CONFIG_2_BAR1_SIZE_512M (14L<<0) #define PCI_CONFIG_2_BAR1_SIZE_1G (15L<<0) -#define PCI_CONFIG_2_BAR1_64ENA (1L<<4) -#define PCI_CONFIG_2_EXP_ROM_RETRY (1L<<5) -#define PCI_CONFIG_2_CFG_CYCLE_RETRY (1L<<6) -#define PCI_CONFIG_2_FIRST_CFG_DONE (1L<<7) -#define PCI_CONFIG_2_EXP_ROM_SIZE (0xffL<<8) +#define PCI_CONFIG_2_BAR1_64ENA (1L<<4) +#define PCI_CONFIG_2_EXP_ROM_RETRY (1L<<5) +#define PCI_CONFIG_2_CFG_CYCLE_RETRY (1L<<6) +#define PCI_CONFIG_2_FIRST_CFG_DONE (1L<<7) +#define PCI_CONFIG_2_EXP_ROM_SIZE (0xffL<<8) #define PCI_CONFIG_2_EXP_ROM_SIZE_DISABLED (0L<<8) #define PCI_CONFIG_2_EXP_ROM_SIZE_2K (1L<<8) #define PCI_CONFIG_2_EXP_ROM_SIZE_4K (2L<<8) @@ -5258,46 +5273,44 @@ #define PCI_CONFIG_2_EXP_ROM_SIZE_8M (13L<<8) #define PCI_CONFIG_2_EXP_ROM_SIZE_16M (14L<<8) #define PCI_CONFIG_2_EXP_ROM_SIZE_32M (15L<<8) -#define PCI_CONFIG_2_BAR_PREFETCH (1L<<16) -#define PCI_CONFIG_2_RESERVED0 (0x7fffL<<17) +#define PCI_CONFIG_2_BAR_PREFETCH (1L<<16) +#define PCI_CONFIG_2_RESERVED0 (0x7fffL<<17) /* config_3 offset */ -#define GRC_CONFIG_3_SIZE_REG (0x40c) -#define PCI_CONFIG_3_STICKY_BYTE (0xffL<<0) -#define PCI_CONFIG_3_FORCE_PME (1L<<24) -#define PCI_CONFIG_3_PME_STATUS (1L<<25) -#define PCI_CONFIG_3_PME_ENABLE (1L<<26) -#define PCI_CONFIG_3_PM_STATE (0x3L<<27) -#define PCI_CONFIG_3_VAUX_PRESET (1L<<30) -#define PCI_CONFIG_3_PCI_POWER (1L<<31) - -/* config_2 offset */ -#define GRC_CONFIG_2_SIZE_REG 0x408 +#define GRC_CONFIG_3_SIZE_REG 0x40c +#define PCI_CONFIG_3_STICKY_BYTE (0xffL<<0) +#define PCI_CONFIG_3_FORCE_PME (1L<<24) +#define PCI_CONFIG_3_PME_STATUS (1L<<25) +#define PCI_CONFIG_3_PME_ENABLE (1L<<26) +#define PCI_CONFIG_3_PM_STATE (0x3L<<27) +#define PCI_CONFIG_3_VAUX_PRESET (1L<<30) +#define PCI_CONFIG_3_PCI_POWER (1L<<31) #define GRC_BAR2_CONFIG 0x4e0 -#define PCI_CONFIG_2_BAR2_SIZE (0xfL<<0) -#define PCI_CONFIG_2_BAR2_SIZE_DISABLED (0L<<0) -#define PCI_CONFIG_2_BAR2_SIZE_64K (1L<<0) -#define PCI_CONFIG_2_BAR2_SIZE_128K (2L<<0) -#define PCI_CONFIG_2_BAR2_SIZE_256K (3L<<0) -#define PCI_CONFIG_2_BAR2_SIZE_512K (4L<<0) -#define PCI_CONFIG_2_BAR2_SIZE_1M (5L<<0) -#define PCI_CONFIG_2_BAR2_SIZE_2M (6L<<0) -#define PCI_CONFIG_2_BAR2_SIZE_4M (7L<<0) -#define PCI_CONFIG_2_BAR2_SIZE_8M (8L<<0) -#define PCI_CONFIG_2_BAR2_SIZE_16M (9L<<0) -#define PCI_CONFIG_2_BAR2_SIZE_32M (10L<<0) -#define PCI_CONFIG_2_BAR2_SIZE_64M (11L<<0) -#define PCI_CONFIG_2_BAR2_SIZE_128M (12L<<0) -#define PCI_CONFIG_2_BAR2_SIZE_256M (13L<<0) -#define PCI_CONFIG_2_BAR2_SIZE_512M (14L<<0) -#define PCI_CONFIG_2_BAR2_SIZE_1G (15L<<0) -#define PCI_CONFIG_2_BAR2_64ENA (1L<<4) +#define PCI_CONFIG_2_BAR2_SIZE (0xfL<<0) +#define PCI_CONFIG_2_BAR2_SIZE_DISABLED (0L<<0) +#define PCI_CONFIG_2_BAR2_SIZE_64K (1L<<0) +#define PCI_CONFIG_2_BAR2_SIZE_128K (2L<<0) +#define PCI_CONFIG_2_BAR2_SIZE_256K (3L<<0) +#define PCI_CONFIG_2_BAR2_SIZE_512K (4L<<0) +#define PCI_CONFIG_2_BAR2_SIZE_1M (5L<<0) +#define PCI_CONFIG_2_BAR2_SIZE_2M (6L<<0) +#define PCI_CONFIG_2_BAR2_SIZE_4M (7L<<0) +#define PCI_CONFIG_2_BAR2_SIZE_8M (8L<<0) +#define PCI_CONFIG_2_BAR2_SIZE_16M (9L<<0) +#define PCI_CONFIG_2_BAR2_SIZE_32M (10L<<0) +#define PCI_CONFIG_2_BAR2_SIZE_64M (11L<<0) +#define PCI_CONFIG_2_BAR2_SIZE_128M (12L<<0) +#define PCI_CONFIG_2_BAR2_SIZE_256M (13L<<0) +#define PCI_CONFIG_2_BAR2_SIZE_512M (14L<<0) +#define PCI_CONFIG_2_BAR2_SIZE_1G (15L<<0) +#define PCI_CONFIG_2_BAR2_64ENA (1L<<4) + +#define PCI_PM_DATA_A 0x410 +#define PCI_PM_DATA_B 0x414 +#define PCI_ID_VAL1 0x434 +#define PCI_ID_VAL2 0x438 -#define PCI_PM_DATA_A (0x410) -#define PCI_PM_DATA_B (0x414) -#define PCI_ID_VAL1 (0x434) -#define PCI_ID_VAL2 (0x438) #define MDIO_REG_BANK_CL73_IEEEB0 0x0 #define MDIO_CL73_IEEEB0_CL73_AN_CONTROL 0x0 @@ -5624,4 +5637,13 @@ Theotherbitsarereservedandshouldbezero*/ #define IGU_INT_NOP 2 #define IGU_INT_NOP2 3 +#define COMMAND_REG_INT_ACK 0x0 +#define COMMAND_REG_PROD_UPD 0x4 +#define COMMAND_REG_ATTN_BITS_UPD 0x8 +#define COMMAND_REG_ATTN_BITS_SET 0xc +#define COMMAND_REG_ATTN_BITS_CLR 0x10 +#define COMMAND_REG_COALESCE_NOW 0x14 +#define COMMAND_REG_SIMD_MASK 0x18 +#define COMMAND_REG_SIMD_NOMASK 0x1c + -- GitLab From 12469401bc5aebb1c1482db1253c986cf8221281 Mon Sep 17 00:00:00 2001 From: Yitchak Gertner Date: Wed, 13 Aug 2008 15:52:08 -0700 Subject: [PATCH 254/750] bnx2x: Delay in while loops Delay in while loops The delay in the loop should be after the change. This has very little effect (can save one delay) but it is the right thing to do Signed-off-by: Yitchak Gertner Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x_main.c | 25 +++++++++++-------------- 1 file changed, 11 insertions(+), 14 deletions(-) diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index b2886db5704..ea6fcf3514b 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -235,17 +235,16 @@ void bnx2x_write_dmae(struct bnx2x *bp, dma_addr_t dma_addr, u32 dst_addr, while (*wb_comp != DMAE_COMP_VAL) { DP(BNX2X_MSG_OFF, "wb_comp 0x%08x\n", *wb_comp); - /* adjust delay for emulation/FPGA */ - if (CHIP_REV_IS_SLOW(bp)) - msleep(100); - else - udelay(5); - if (!cnt) { BNX2X_ERR("dmae timeout!\n"); break; } cnt--; + /* adjust delay for emulation/FPGA */ + if (CHIP_REV_IS_SLOW(bp)) + msleep(100); + else + udelay(5); } mutex_unlock(&bp->dmae_mutex); @@ -308,17 +307,16 @@ void bnx2x_read_dmae(struct bnx2x *bp, u32 src_addr, u32 len32) while (*wb_comp != DMAE_COMP_VAL) { - /* adjust delay for emulation/FPGA */ - if (CHIP_REV_IS_SLOW(bp)) - msleep(100); - else - udelay(5); - if (!cnt) { BNX2X_ERR("dmae timeout!\n"); break; } cnt--; + /* adjust delay for emulation/FPGA */ + if (CHIP_REV_IS_SLOW(bp)) + msleep(100); + else + udelay(5); } DP(BNX2X_MSG_OFF, "data [0x%08x 0x%08x 0x%08x 0x%08x]\n", bp->slowpath->wb_data[0], bp->slowpath->wb_data[1], @@ -3094,12 +3092,12 @@ static int bnx2x_stats_comp(struct bnx2x *bp) might_sleep(); while (*stats_comp != DMAE_COMP_VAL) { - msleep(1); if (!cnt) { BNX2X_ERR("timeout waiting for stats finished\n"); break; } cnt--; + msleep(1); } return 1; } @@ -6483,7 +6481,6 @@ static int bnx2x_stop_leading(struct bnx2x *bp) so there is not much to do if this times out */ while (dsb_sp_prod_idx == *bp->dsb_sp_prod) { - msleep(1); if (!cnt) { DP(NETIF_MSG_IFDOWN, "timeout waiting for port del " "dsb_sp_prod 0x%x != dsb_sp_prod_idx 0x%x\n", -- GitLab From 3101c2bc9043c1499158837648a29dd79ee2f5e7 Mon Sep 17 00:00:00 2001 From: Yitchak Gertner Date: Wed, 13 Aug 2008 15:52:28 -0700 Subject: [PATCH 255/750] bnx2x: Clearing MAC addresses filters Clearing MAC addresses filters When the driver unloads, it should clear the MAC addresses filters in the HW - this prevents packets from entering the chip when the driver is re-loaded before initializing the right filters Signed-off-by: Yitchak Gertner Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x_main.c | 68 +++++++++++++++++++++++++++++++--------- 1 file changed, 54 insertions(+), 14 deletions(-) diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index ea6fcf3514b..db6a3b9a367 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -6048,7 +6048,7 @@ static int bnx2x_req_irq(struct bnx2x *bp) * Init service functions */ -static void bnx2x_set_mac_addr_e1(struct bnx2x *bp) +static void bnx2x_set_mac_addr_e1(struct bnx2x *bp, int set) { struct mac_configuration_cmd *config = bnx2x_sp(bp, mac_config); int port = BP_PORT(bp); @@ -6070,11 +6070,15 @@ static void bnx2x_set_mac_addr_e1(struct bnx2x *bp) config->config_table[0].cam_entry.lsb_mac_addr = swab16(*(u16 *)&bp->dev->dev_addr[4]); config->config_table[0].cam_entry.flags = cpu_to_le16(port); - config->config_table[0].target_table_entry.flags = 0; + if (set) + config->config_table[0].target_table_entry.flags = 0; + else + CAM_INVALIDATE(config->config_table[0]); config->config_table[0].target_table_entry.client_id = 0; config->config_table[0].target_table_entry.vlan_id = 0; - DP(NETIF_MSG_IFUP, "setting MAC (%04x:%04x:%04x)\n", + DP(NETIF_MSG_IFUP, "%s MAC (%04x:%04x:%04x)\n", + (set ? "setting" : "clearing"), config->config_table[0].cam_entry.msb_mac_addr, config->config_table[0].cam_entry.middle_mac_addr, config->config_table[0].cam_entry.lsb_mac_addr); @@ -6084,8 +6088,11 @@ static void bnx2x_set_mac_addr_e1(struct bnx2x *bp) config->config_table[1].cam_entry.middle_mac_addr = 0xffff; config->config_table[1].cam_entry.lsb_mac_addr = 0xffff; config->config_table[1].cam_entry.flags = cpu_to_le16(port); - config->config_table[1].target_table_entry.flags = + if (set) + config->config_table[1].target_table_entry.flags = TSTORM_CAM_TARGET_TABLE_ENTRY_BROADCAST; + else + CAM_INVALIDATE(config->config_table[1]); config->config_table[1].target_table_entry.client_id = 0; config->config_table[1].target_table_entry.vlan_id = 0; @@ -6094,12 +6101,12 @@ static void bnx2x_set_mac_addr_e1(struct bnx2x *bp) U64_LO(bnx2x_sp_mapping(bp, mac_config)), 0); } -static void bnx2x_set_mac_addr_e1h(struct bnx2x *bp) +static void bnx2x_set_mac_addr_e1h(struct bnx2x *bp, int set) { struct mac_configuration_cmd_e1h *config = (struct mac_configuration_cmd_e1h *)bnx2x_sp(bp, mac_config); - if (bp->state != BNX2X_STATE_OPEN) { + if (set && (bp->state != BNX2X_STATE_OPEN)) { DP(NETIF_MSG_IFUP, "state is %x, returning\n", bp->state); return; } @@ -6123,9 +6130,14 @@ static void bnx2x_set_mac_addr_e1h(struct bnx2x *bp) config->config_table[0].client_id = BP_L_ID(bp); config->config_table[0].vlan_id = 0; config->config_table[0].e1hov_id = cpu_to_le16(bp->e1hov); - config->config_table[0].flags = BP_PORT(bp); + if (set) + config->config_table[0].flags = BP_PORT(bp); + else + config->config_table[0].flags = + MAC_CONFIGURATION_ENTRY_E1H_ACTION_TYPE; - DP(NETIF_MSG_IFUP, "setting MAC (%04x:%04x:%04x) E1HOV %d CLID %d\n", + DP(NETIF_MSG_IFUP, "%s MAC (%04x:%04x:%04x) E1HOV %d CLID %d\n", + (set ? "setting" : "clearing"), config->config_table[0].msb_mac_addr, config->config_table[0].middle_mac_addr, config->config_table[0].lsb_mac_addr, bp->e1hov, BP_L_ID(bp)); @@ -6150,13 +6162,13 @@ static int bnx2x_wait_ramrod(struct bnx2x *bp, int state, int idx, bnx2x_rx_int(bp->fp, 10); /* if index is different from 0 * the reply for some commands will - * be on the none default queue + * be on the non default queue */ if (idx) bnx2x_rx_int(&bp->fp[idx], 10); } - mb(); /* state is changed by bnx2x_sp_event() */ + mb(); /* state is changed by bnx2x_sp_event() */ if (*state_p == state) return 0; @@ -6364,9 +6376,9 @@ static int bnx2x_nic_load(struct bnx2x *bp, int load_mode) } if (CHIP_IS_E1(bp)) - bnx2x_set_mac_addr_e1(bp); + bnx2x_set_mac_addr_e1(bp, 1); else - bnx2x_set_mac_addr_e1h(bp); + bnx2x_set_mac_addr_e1h(bp, 1); if (bp->port.pmf) bnx2x_initial_phy_init(bp); @@ -6668,6 +6680,34 @@ static int bnx2x_nic_unload(struct bnx2x *bp, int unload_mode) } else reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS; + if (CHIP_IS_E1(bp)) { + struct mac_configuration_cmd *config = + bnx2x_sp(bp, mcast_config); + + bnx2x_set_mac_addr_e1(bp, 0); + + for (i = 0; i < config->hdr.length_6b; i++) + CAM_INVALIDATE(config->config_table[i]); + + config->hdr.length_6b = i; + if (CHIP_REV_IS_SLOW(bp)) + config->hdr.offset = BNX2X_MAX_EMUL_MULTI*(1 + port); + else + config->hdr.offset = BNX2X_MAX_MULTICAST*(1 + port); + config->hdr.client_id = BP_CL_ID(bp); + config->hdr.reserved1 = 0; + + bnx2x_sp_post(bp, RAMROD_CMD_ID_ETH_SET_MAC, 0, + U64_HI(bnx2x_sp_mapping(bp, mcast_config)), + U64_LO(bnx2x_sp_mapping(bp, mcast_config)), 0); + + } else { /* E1H */ + bnx2x_set_mac_addr_e1h(bp, 0); + + for (i = 0; i < MC_HASH_SIZE; i++) + REG_WR(bp, MC_HASH_OFFSET(bp, i), 0); + } + if (CHIP_IS_E1H(bp)) REG_WR(bp, NIG_REG_LLH0_FUNC_EN + port*8, 0); @@ -9811,9 +9851,9 @@ static int bnx2x_change_mac_addr(struct net_device *dev, void *p) memcpy(dev->dev_addr, addr->sa_data, dev->addr_len); if (netif_running(dev)) { if (CHIP_IS_E1(bp)) - bnx2x_set_mac_addr_e1(bp); + bnx2x_set_mac_addr_e1(bp, 1); else - bnx2x_set_mac_addr_e1h(bp); + bnx2x_set_mac_addr_e1h(bp, 1); } return 0; -- GitLab From 72ce58c328d7131d96280135f8be858603522911 Mon Sep 17 00:00:00 2001 From: Eilon Greenstein Date: Wed, 13 Aug 2008 15:52:46 -0700 Subject: [PATCH 256/750] bnx2x: WoL capability WoL capability All designs reported WoL capability regardless of HW limitations - check if this device is actually capable of WoL Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x_main.c | 13 +++++++++++-- 1 file changed, 11 insertions(+), 2 deletions(-) diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index db6a3b9a367..03218705f51 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -6897,6 +6897,7 @@ static void __devinit bnx2x_undi_unload(struct bnx2x *bp) static void __devinit bnx2x_get_common_hwinfo(struct bnx2x *bp) { u32 val, val2, val3, val4, id; + u16 pmc; /* Get the chip revision id and number. */ /* chip num:16-31, rev:12-15, metal:4-11, bond_id:0-3 */ @@ -6954,8 +6955,16 @@ static void __devinit bnx2x_get_common_hwinfo(struct bnx2x *bp) BNX2X_ERR("This driver needs bc_ver %X but found %X," " please upgrade BC\n", BNX2X_BC_VER, val); } - BNX2X_DEV_INFO("%sWoL Capable\n", - (bp->flags & NO_WOL_FLAG)? "Not " : ""); + + if (BP_E1HVN(bp) == 0) { + pci_read_config_word(bp->pdev, bp->pm_cap + PCI_PM_PMC, &pmc); + bp->flags |= (pmc & PCI_PM_CAP_PME_D3cold) ? 0 : NO_WOL_FLAG; + } else { + /* no WOL capability for E1HVN != 0 */ + bp->flags |= NO_WOL_FLAG; + } + BNX2X_DEV_INFO("%sWoL capable\n", + (bp->flags & NO_WOL_FLAG) ? "Not " : ""); val = SHMEM_RD(bp, dev_info.shared_hw_config.part_num); val2 = SHMEM_RD(bp, dev_info.shared_hw_config.part_num[4]); -- GitLab From 353029896a5ed6cf42f4ce45729851b23c94d874 Mon Sep 17 00:00:00 2001 From: Yitchak Gertner Date: Wed, 13 Aug 2008 15:53:12 -0700 Subject: [PATCH 257/750] bnx2x: Wrong structure size Wrong structure size The wrong structure was used in the sizeof to clear (luckily both structures have the same size in this version...) Signed-off-by: Yitchak Gertner Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x_main.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index 03218705f51..6fe19726ae4 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -3985,10 +3985,10 @@ static void bnx2x_zero_sb(struct bnx2x *bp, int sb_id) bnx2x_init_fill(bp, BAR_USTRORM_INTMEM + USTORM_SB_HOST_STATUS_BLOCK_OFFSET(port, sb_id), 0, - sizeof(struct ustorm_def_status_block)/4); + sizeof(struct ustorm_status_block)/4); bnx2x_init_fill(bp, BAR_CSTRORM_INTMEM + CSTORM_SB_HOST_STATUS_BLOCK_OFFSET(port, sb_id), 0, - sizeof(struct cstorm_def_status_block)/4); + sizeof(struct cstorm_status_block)/4); } static void bnx2x_init_sb(struct bnx2x *bp, struct host_status_block *sb, -- GitLab From df0f23439a69eb5ca30668612f1c4e20041b5341 Mon Sep 17 00:00:00 2001 From: Vladislav Zolotarov Date: Wed, 13 Aug 2008 15:53:38 -0700 Subject: [PATCH 258/750] bnx2x: No LRO without Rx checksum No LRO without Rx checksum Disabling LRO when Rx checksum is disabled Signed-off-by: Vladislav Zolotarov Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x_main.c | 67 +++++++++++++++++++++++----------------- 1 file changed, 39 insertions(+), 28 deletions(-) diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index 6fe19726ae4..d29f22763fe 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -8272,33 +8272,6 @@ static int bnx2x_set_coalesce(struct net_device *dev, return 0; } -static int bnx2x_set_flags(struct net_device *dev, u32 data) -{ - struct bnx2x *bp = netdev_priv(dev); - int changed = 0; - int rc = 0; - - if (data & ETH_FLAG_LRO) { - if (!(dev->features & NETIF_F_LRO)) { - dev->features |= NETIF_F_LRO; - bp->flags |= TPA_ENABLE_FLAG; - changed = 1; - } - - } else if (dev->features & NETIF_F_LRO) { - dev->features &= ~NETIF_F_LRO; - bp->flags &= ~TPA_ENABLE_FLAG; - changed = 1; - } - - if (changed && netif_running(dev)) { - bnx2x_nic_unload(bp, UNLOAD_NORMAL); - rc = bnx2x_nic_load(bp, LOAD_NORMAL); - } - - return rc; -} - static void bnx2x_get_ringparam(struct net_device *dev, struct ethtool_ringparam *ering) { @@ -8400,6 +8373,34 @@ static int bnx2x_set_pauseparam(struct net_device *dev, return 0; } +static int bnx2x_set_flags(struct net_device *dev, u32 data) +{ + struct bnx2x *bp = netdev_priv(dev); + int changed = 0; + int rc = 0; + + /* TPA requires Rx CSUM offloading */ + if ((data & ETH_FLAG_LRO) && bp->rx_csum) { + if (!(dev->features & NETIF_F_LRO)) { + dev->features |= NETIF_F_LRO; + bp->flags |= TPA_ENABLE_FLAG; + changed = 1; + } + + } else if (dev->features & NETIF_F_LRO) { + dev->features &= ~NETIF_F_LRO; + bp->flags &= ~TPA_ENABLE_FLAG; + changed = 1; + } + + if (changed && netif_running(dev)) { + bnx2x_nic_unload(bp, UNLOAD_NORMAL); + rc = bnx2x_nic_load(bp, LOAD_NORMAL); + } + + return rc; +} + static u32 bnx2x_get_rx_csum(struct net_device *dev) { struct bnx2x *bp = netdev_priv(dev); @@ -8410,9 +8411,19 @@ static u32 bnx2x_get_rx_csum(struct net_device *dev) static int bnx2x_set_rx_csum(struct net_device *dev, u32 data) { struct bnx2x *bp = netdev_priv(dev); + int rc = 0; bp->rx_csum = data; - return 0; + + /* Disable TPA, when Rx CSUM is disabled. Otherwise all + TPA'ed packets will be discarded due to wrong TCP CSUM */ + if (!data) { + u32 flags = ethtool_op_get_flags(dev); + + rc = bnx2x_set_flags(dev, (flags & ~ETH_FLAG_LRO)); + } + + return rc; } static int bnx2x_set_tso(struct net_device *dev, u32 data) -- GitLab From 57963ed94c27e94a7533434da5943195ea072a35 Mon Sep 17 00:00:00 2001 From: Yaniv Rosner Date: Wed, 13 Aug 2008 15:55:28 -0700 Subject: [PATCH 259/750] bnx2x: Link order with external PHY Link order with external PHY When external PHY exists (second chip with the PHY to translate to another physical medium) the link with the eternal PHY and the network should be established before setting the link between the 5771x and the PHY. This is the right order and it is important when using autoneg - the link to the network should use the autoneg and the link between the two chips should be forced to the network result. Signed-off-by: Yaniv Rosner Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x_link.c | 380 ++++++++++++++++++++++----------------- drivers/net/bnx2x_reg.h | 2 + 2 files changed, 216 insertions(+), 166 deletions(-) diff --git a/drivers/net/bnx2x_link.c b/drivers/net/bnx2x_link.c index ff2743db10d..3b63c8ce952 100644 --- a/drivers/net/bnx2x_link.c +++ b/drivers/net/bnx2x_link.c @@ -1690,7 +1690,11 @@ static u8 bnx2x_link_settings_status(struct link_params *params, vars->link_status |= LINK_STATUS_SERDES_LINK; - if (params->req_line_speed == SPEED_AUTO_NEG) { + if ((params->req_line_speed == SPEED_AUTO_NEG) && + ((XGXS_EXT_PHY_TYPE(params->ext_phy_config) == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) || + (XGXS_EXT_PHY_TYPE(params->ext_phy_config) == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705))) { vars->autoneg = AUTO_NEG_ENABLED; if (gp_status & MDIO_AN_CL73_OR_37_COMPLETE) { @@ -1716,7 +1720,7 @@ static u8 bnx2x_link_settings_status(struct link_params *params, DP(NETIF_MSG_LINK, "phy link down\n"); vars->phy_link_up = 0; - vars->line_speed = 0; + vars->duplex = DUPLEX_FULL; vars->flow_ctrl = FLOW_CTRL_NONE; vars->autoneg = AUTO_NEG_DISABLED; @@ -2302,6 +2306,65 @@ static void bnx2x_ext_phy_set_pause(struct link_params *params, MDIO_AN_REG_ADV_PAUSE, val); } + +static void bnx2x_init_internal_phy(struct link_params *params, + struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + if (!(vars->phy_flags & PHY_SGMII_FLAG)) { + u16 bank, rx_eq; + + rx_eq = ((params->serdes_config & + PORT_HW_CFG_SERDES_RX_DRV_EQUALIZER_MASK) >> + PORT_HW_CFG_SERDES_RX_DRV_EQUALIZER_SHIFT); + + DP(NETIF_MSG_LINK, "setting rx eq to 0x%x\n", rx_eq); + for (bank = MDIO_REG_BANK_RX0; bank <= MDIO_REG_BANK_RX_ALL; + bank += (MDIO_REG_BANK_RX1-MDIO_REG_BANK_RX0)) { + CL45_WR_OVER_CL22(bp, port, + params->phy_addr, + bank , + MDIO_RX0_RX_EQ_BOOST, + ((rx_eq & + MDIO_RX0_RX_EQ_BOOST_EQUALIZER_CTRL_MASK) | + MDIO_RX0_RX_EQ_BOOST_OFFSET_CTRL)); + } + + /* forced speed requested? */ + if (vars->line_speed != SPEED_AUTO_NEG) { + DP(NETIF_MSG_LINK, "not SGMII, no AN\n"); + + /* disable autoneg */ + bnx2x_set_autoneg(params, vars); + + /* program speed and duplex */ + bnx2x_program_serdes(params); + + } else { /* AN_mode */ + DP(NETIF_MSG_LINK, "not SGMII, AN\n"); + + /* AN enabled */ + bnx2x_set_brcm_cl37_advertisment(params); + + /* program duplex & pause advertisement (for aneg) */ + bnx2x_set_ieee_aneg_advertisment(params, + &vars->ieee_fc); + + /* enable autoneg */ + bnx2x_set_autoneg(params, vars); + + /* enable and restart AN */ + bnx2x_restart_autoneg(params); + } + + } else { /* SGMII mode */ + DP(NETIF_MSG_LINK, "SGMII\n"); + + bnx2x_initialize_sgmii_process(params); + } +} + static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) { struct bnx2x *bp = params->bp; @@ -2343,7 +2406,6 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) switch (ext_phy_type) { case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT: - DP(NETIF_MSG_LINK, "XGXS Direct\n"); break; case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705: @@ -2701,10 +2763,7 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) } } else { /* SerDes */ -/* ext_phy_addr = ((bp->ext_phy_config & - PORT_HW_CFG_SERDES_EXT_PHY_ADDR_MASK) >> - PORT_HW_CFG_SERDES_EXT_PHY_ADDR_SHIFT); -*/ + ext_phy_type = SERDES_EXT_PHY_TYPE(params->ext_phy_config); switch (ext_phy_type) { case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT: @@ -2810,6 +2869,13 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, */ ext_phy_link_up = ((rx_sd & pcs_status & 0x1) || (val2 & (1<<1))); + if (ext_phy_link_up) { + if (val2 & (1<<1)) + vars->line_speed = SPEED_1000; + else + vars->line_speed = SPEED_10000; + } + /* clear LASI indication*/ bnx2x_cl45_read(bp, params->port, ext_phy_type, ext_phy_addr, @@ -3006,6 +3072,7 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, MDIO_AN_DEVAD, MDIO_AN_REG_MASTER_STATUS, &val2); + vars->line_speed = SPEED_10000; DP(NETIF_MSG_LINK, "SFX7101 AN status 0x%x->Master=%x\n", val2, @@ -3181,7 +3248,8 @@ static u8 bnx2x_format_ver(u32 num, u8 *str, u16 len) } -static void bnx2x_turn_on_sf(struct bnx2x *bp, u8 port, u8 ext_phy_addr) +static void bnx2x_turn_on_ef(struct bnx2x *bp, u8 port, u8 ext_phy_addr, + u32 ext_phy_type) { u32 cnt = 0; u16 ctrl = 0; @@ -3205,7 +3273,7 @@ static void bnx2x_turn_on_sf(struct bnx2x *bp, u8 port, u8 ext_phy_addr) for (cnt = 0; cnt < 1000; cnt++) { msleep(1); bnx2x_cl45_read(bp, port, - PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101, + ext_phy_type, ext_phy_addr, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, @@ -3253,7 +3321,8 @@ u8 bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded, /* Take ext phy out of reset */ if (!driver_loaded) - bnx2x_turn_on_sf(bp, params->port, ext_phy_addr); + bnx2x_turn_on_ef(bp, params->port, ext_phy_addr, + ext_phy_type); /* wait for 1ms */ msleep(1); @@ -3281,6 +3350,11 @@ u8 bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded, case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072: case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: { + /* Take ext phy out of reset */ + if (!driver_loaded) + bnx2x_turn_on_ef(bp, params->port, ext_phy_addr, + ext_phy_type); + bnx2x_cl45_read(bp, params->port, ext_phy_type, ext_phy_addr, MDIO_PMA_DEVAD, @@ -3622,7 +3696,8 @@ static u8 bnx2x_link_initialize(struct link_params *params, struct bnx2x *bp = params->bp; u8 port = params->port; u8 rc = 0; - + u8 non_ext_phy; + u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); /* Activate the external PHY */ bnx2x_ext_phy_reset(params, vars); @@ -3644,10 +3719,6 @@ static u8 bnx2x_link_initialize(struct link_params *params, bnx2x_set_swap_lanes(params); } - /* Set Parallel Detect */ - if (params->req_line_speed == SPEED_AUTO_NEG) - bnx2x_set_parallel_detection(params, vars->phy_flags); - if (vars->phy_flags & PHY_XGXS_FLAG) { if (params->req_line_speed && ((params->req_line_speed == SPEED_100) || @@ -3657,68 +3728,33 @@ static u8 bnx2x_link_initialize(struct link_params *params, vars->phy_flags &= ~PHY_SGMII_FLAG; } } + /* In case of external phy existance, the line speed would be the + line speed linked up by the external phy. In case it is direct only, + then the line_speed during initialization will be equal to the + req_line_speed*/ + vars->line_speed = params->req_line_speed; - if (!(vars->phy_flags & PHY_SGMII_FLAG)) { - u16 bank, rx_eq; - - rx_eq = ((params->serdes_config & - PORT_HW_CFG_SERDES_RX_DRV_EQUALIZER_MASK) >> - PORT_HW_CFG_SERDES_RX_DRV_EQUALIZER_SHIFT); - - DP(NETIF_MSG_LINK, "setting rx eq to 0x%x\n", rx_eq); - for (bank = MDIO_REG_BANK_RX0; bank <= MDIO_REG_BANK_RX_ALL; - bank += (MDIO_REG_BANK_RX1-MDIO_REG_BANK_RX0)) { - CL45_WR_OVER_CL22(bp, port, - params->phy_addr, - bank , - MDIO_RX0_RX_EQ_BOOST, - ((rx_eq & - MDIO_RX0_RX_EQ_BOOST_EQUALIZER_CTRL_MASK) | - MDIO_RX0_RX_EQ_BOOST_OFFSET_CTRL)); - } - - /* forced speed requested? */ - if (params->req_line_speed != SPEED_AUTO_NEG) { - DP(NETIF_MSG_LINK, "not SGMII, no AN\n"); - - /* disable autoneg */ - bnx2x_set_autoneg(params, vars); - - /* program speed and duplex */ - bnx2x_program_serdes(params); - vars->ieee_fc = - MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE; - - } else { /* AN_mode */ - DP(NETIF_MSG_LINK, "not SGMII, AN\n"); - - /* AN enabled */ - bnx2x_set_brcm_cl37_advertisment(params); - - /* program duplex & pause advertisement (for aneg) */ - bnx2x_set_ieee_aneg_advertisment(params, - &vars->ieee_fc); - - /* enable autoneg */ - bnx2x_set_autoneg(params, vars); - - /* enable and restart AN */ - bnx2x_restart_autoneg(params); - } + bnx2x_set_ieee_aneg_advertisment(params, &vars->ieee_fc); - } else { /* SGMII mode */ - DP(NETIF_MSG_LINK, "SGMII\n"); - - bnx2x_initialize_sgmii_process(params); + /* init ext phy and enable link state int */ + non_ext_phy = ((ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) || + (params->loopback_mode == LOOPBACK_XGXS_10) || + (params->loopback_mode == LOOPBACK_EXT_PHY)); + + if (non_ext_phy || + (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705)) { + if (params->req_line_speed == SPEED_AUTO_NEG) + bnx2x_set_parallel_detection(params, vars->phy_flags); + bnx2x_init_internal_phy(params, vars); } - /* init ext phy and enable link state int */ - rc |= bnx2x_ext_phy_init(params, vars); + if (!non_ext_phy) + rc |= bnx2x_ext_phy_init(params, vars); bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4, - (NIG_STATUS_XGXS0_LINK10G | - NIG_STATUS_XGXS0_LINK_STATUS | - NIG_STATUS_SERDES0_LINK_STATUS)); + (NIG_STATUS_XGXS0_LINK10G | + NIG_STATUS_XGXS0_LINK_STATUS | + NIG_STATUS_SERDES0_LINK_STATUS)); return rc; @@ -3734,6 +3770,13 @@ u8 bnx2x_phy_init(struct link_params *params, struct link_vars *vars) DP(NETIF_MSG_LINK, "req_speed = %d, req_flowctrl=%d\n", params->req_line_speed, params->req_flow_ctrl); vars->link_status = 0; + vars->phy_link_up = 0; + vars->link_up = 0; + vars->line_speed = 0; + vars->duplex = DUPLEX_FULL; + vars->flow_ctrl = FLOW_CTRL_NONE; + vars->mac_type = MAC_TYPE_NONE; + if (params->switch_cfg == SWITCH_CFG_1G) vars->phy_flags = PHY_SERDES_FLAG; else @@ -3894,6 +3937,7 @@ u8 bnx2x_phy_init(struct link_params *params, struct link_vars *vars) } bnx2x_link_initialize(params, vars); + msleep(30); bnx2x_link_int_enable(params); } return 0; @@ -3949,33 +3993,13 @@ u8 bnx2x_link_reset(struct link_params *params, struct link_vars *vars) MISC_REGISTERS_GPIO_OUTPUT_LOW); DP(NETIF_MSG_LINK, "reset external PHY\n"); - } else { - - u8 ext_phy_addr = ((ext_phy_config & - PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >> - PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT); - - /* SW reset */ - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_CTRL, - 1<<15); - - /* Set Low Power Mode */ - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_CTRL, - 1<<11); - - - if (ext_phy_type == - PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) { - DP(NETIF_MSG_LINK, "Setting 8073 port %d into" + } else if (ext_phy_type == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) { + DP(NETIF_MSG_LINK, "Setting 8073 port %d into " "low power mode\n", port); bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, MISC_REGISTERS_GPIO_OUTPUT_LOW); - } } } /* reset the SerDes/XGXS */ @@ -3995,6 +4019,73 @@ u8 bnx2x_link_reset(struct link_params *params, struct link_vars *vars) return 0; } +static u8 bnx2x_update_link_down(struct link_params *params, + struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + DP(NETIF_MSG_LINK, "Port %x: Link is down\n", port); + bnx2x_set_led(bp, port, LED_MODE_OFF, + 0, params->hw_led_mode, + params->chip_id); + + /* indicate no mac active */ + vars->mac_type = MAC_TYPE_NONE; + + /* update shared memory */ + vars->link_status = 0; + vars->line_speed = 0; + bnx2x_update_mng(params, vars->link_status); + + /* activate nig drain */ + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1); + + /* reset BigMac */ + bnx2x_bmac_rx_disable(bp, params->port); + REG_WR(bp, GRCBASE_MISC + + MISC_REGISTERS_RESET_REG_2_CLEAR, + (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); + return 0; +} + +static u8 bnx2x_update_link_up(struct link_params *params, + struct link_vars *vars, + u8 link_10g, u32 gp_status) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + u8 rc = 0; + vars->link_status |= LINK_STATUS_LINK_UP; + if (link_10g) { + bnx2x_bmac_enable(params, vars, 0); + bnx2x_set_led(bp, port, LED_MODE_OPER, + SPEED_10000, params->hw_led_mode, + params->chip_id); + + } else { + bnx2x_emac_enable(params, vars, 0); + rc = bnx2x_emac_program(params, vars->line_speed, + vars->duplex); + + /* AN complete? */ + if (gp_status & MDIO_AN_CL73_OR_37_COMPLETE) { + if (!(vars->phy_flags & + PHY_SGMII_FLAG)) + bnx2x_set_sgmii_tx_driver(params); + } + } + + /* PBF - link up */ + rc |= bnx2x_pbf_update(params, vars->flow_ctrl, + vars->line_speed); + + /* disable drain */ + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 0); + + /* update shared memory */ + bnx2x_update_mng(params, vars->link_status); + return rc; +} /* This function should called upon link interrupt */ /* In case vars->link_up, driver needs to 1. Update the pbf @@ -4012,10 +4103,10 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) { struct bnx2x *bp = params->bp; u8 port = params->port; - u16 i; u16 gp_status; - u16 link_10g; - u8 rc = 0; + u8 link_10g; + u8 ext_phy_link_up, rc = 0; + u32 ext_phy_type; DP(NETIF_MSG_LINK, "port %x, XGXS?%x, int_status 0x%x\n", port, @@ -4031,15 +4122,16 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68), REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK_STATUS + port*0x68)); + ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); - /* avoid fast toggling */ - for (i = 0; i < 10; i++) { - msleep(10); - CL45_RD_OVER_CL22(bp, port, params->phy_addr, - MDIO_REG_BANK_GP_STATUS, - MDIO_GP_STATUS_TOP_AN_STATUS1, - &gp_status); - } + /* Check external link change only for non-direct */ + ext_phy_link_up = bnx2x_ext_phy_is_link_up(params, vars); + + /* Read gp_status */ + CL45_RD_OVER_CL22(bp, port, params->phy_addr, + MDIO_REG_BANK_GP_STATUS, + MDIO_GP_STATUS_TOP_AN_STATUS1, + &gp_status); rc = bnx2x_link_settings_status(params, vars, gp_status); if (rc != 0) @@ -4055,69 +4147,25 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) bnx2x_link_int_ack(params, vars, link_10g); - /* link is up only if both local phy and external phy are up */ - vars->link_up = (vars->phy_link_up && - bnx2x_ext_phy_is_link_up(params, vars)); - - if (!vars->phy_link_up && - REG_RD(bp, NIG_REG_EMAC0_STATUS_MISC_MI_INT + port*0x18)) { - bnx2x_ext_phy_is_link_up(params, vars); /* Clear interrupt */ - } - - if (vars->link_up) { - vars->link_status |= LINK_STATUS_LINK_UP; - if (link_10g) { - bnx2x_bmac_enable(params, vars, 0); - bnx2x_set_led(bp, port, LED_MODE_OPER, - SPEED_10000, params->hw_led_mode, - params->chip_id); - - } else { - bnx2x_emac_enable(params, vars, 0); - rc = bnx2x_emac_program(params, vars->line_speed, - vars->duplex); - - /* AN complete? */ - if (gp_status & MDIO_AN_CL73_OR_37_COMPLETE) { - if (!(vars->phy_flags & - PHY_SGMII_FLAG)) - bnx2x_set_sgmii_tx_driver(params); - } - } - - /* PBF - link up */ - rc |= bnx2x_pbf_update(params, vars->flow_ctrl, - vars->line_speed); + /* In case external phy link is up, and internal link is down + ( not initialized yet probably after link initialization, it needs + to be initialized. + Note that after link down-up as result of cable plug, + the xgxs link would probably become up again without the need to + initialize it*/ - /* disable drain */ - REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 0); + if ((ext_phy_type != PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT) && + (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705) && + (ext_phy_link_up && !vars->phy_link_up)) + bnx2x_init_internal_phy(params, vars); - /* update shared memory */ - bnx2x_update_mng(params, vars->link_status); - - } else { /* link down */ - DP(NETIF_MSG_LINK, "Port %x: Link is down\n", params->port); - bnx2x_set_led(bp, port, LED_MODE_OFF, - 0, params->hw_led_mode, - params->chip_id); - - /* indicate no mac active */ - vars->mac_type = MAC_TYPE_NONE; - - /* update shared memory */ - vars->link_status = 0; - bnx2x_update_mng(params, vars->link_status); - - /* activate nig drain */ - REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1); - - /* reset BigMac */ - bnx2x_bmac_rx_disable(bp, params->port); - REG_WR(bp, GRCBASE_MISC + - MISC_REGISTERS_RESET_REG_2_CLEAR, - (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); + /* link is up only if both local phy and external phy are up */ + vars->link_up = (ext_phy_link_up && vars->phy_link_up); - } + if (vars->link_up) + rc = bnx2x_update_link_up(params, vars, link_10g, gp_status); + else + rc = bnx2x_update_link_down(params, vars); return rc; } @@ -4508,7 +4556,7 @@ u8 bnx2x_flash_download(struct bnx2x *bp, u8 port, u32 ext_phy_config, case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101: /* Take ext phy out of reset */ if (!driver_loaded) - bnx2x_turn_on_sf(bp, port, ext_phy_addr); + bnx2x_turn_on_ef(bp, port, ext_phy_addr, ext_phy_type); rc = bnx2x_sfx7101_flash_download(bp, port, ext_phy_addr, data, size); if (!driver_loaded) diff --git a/drivers/net/bnx2x_reg.h b/drivers/net/bnx2x_reg.h index a85ff207368..58fbeb1cf78 100644 --- a/drivers/net/bnx2x_reg.h +++ b/drivers/net/bnx2x_reg.h @@ -5559,6 +5559,8 @@ Theotherbitsarereservedandshouldbezero*/ #define MDIO_PMA_REG_GEN_CTRL 0xca10 #define MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP 0x0188 #define MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET 0x018a +#define MDIO_PMA_REG_M8051_MSGIN_REG 0xca12 +#define MDIO_PMA_REG_M8051_MSGOUT_REG 0xca13 #define MDIO_PMA_REG_ROM_VER1 0xca19 #define MDIO_PMA_REG_ROM_VER2 0xca1a #define MDIO_PMA_REG_EDC_FFE_MAIN 0xca1b -- GitLab From 8c99e7b0436473593a68e740d1032909bc5335a1 Mon Sep 17 00:00:00 2001 From: Yaniv Rosner Date: Wed, 13 Aug 2008 15:56:17 -0700 Subject: [PATCH 260/750] bnx2x: Pause settings Pause settings - 1G pause was not working due to missing write to the emac block (TX_MODE_FLOW_EN) - The flow control should use the negotiated result (after autoneg) so we should save both the requested autoneg and the result - The HW credits with flow control at 1G speed were not optimized and caused low throughput - It is recommended to turn off flow control if the MTU is bigger than 5000B due to internal buffers size Signed-off-by: Yaniv Rosner Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x_link.c | 202 ++++++++++++++++++++++----------------- drivers/net/bnx2x_link.h | 4 +- drivers/net/bnx2x_main.c | 9 +- drivers/net/bnx2x_reg.h | 4 +- 4 files changed, 128 insertions(+), 91 deletions(-) diff --git a/drivers/net/bnx2x_link.c b/drivers/net/bnx2x_link.c index 3b63c8ce952..36fa356c74f 100644 --- a/drivers/net/bnx2x_link.c +++ b/drivers/net/bnx2x_link.c @@ -38,7 +38,6 @@ #define ETH_MAX_JUMBO_PACKET_SIZE 9600 #define MDIO_ACCESS_TIMEOUT 1000 #define BMAC_CONTROL_RX_ENABLE 2 -#define MAX_MTU_SIZE 5000 /***********************************************************/ /* Shortcut definitions */ @@ -298,11 +297,13 @@ static u8 bnx2x_emac_enable(struct link_params *params, EMAC_RX_MODE_FLOW_EN); bnx2x_bits_dis(bp, emac_base + EMAC_REG_EMAC_TX_MODE, - EMAC_TX_MODE_EXT_PAUSE_EN); + (EMAC_TX_MODE_EXT_PAUSE_EN | + EMAC_TX_MODE_FLOW_EN)); if (vars->flow_ctrl & FLOW_CTRL_TX) bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_TX_MODE, - EMAC_TX_MODE_EXT_PAUSE_EN); + (EMAC_TX_MODE_EXT_PAUSE_EN | + EMAC_TX_MODE_FLOW_EN)); } /* KEEP_VLAN_TAG, promiscuous */ @@ -591,9 +592,9 @@ void bnx2x_link_status_update(struct link_params *params, vars->flow_ctrl &= ~FLOW_CTRL_RX; if (vars->phy_flags & PHY_XGXS_FLAG) { - if (params->req_line_speed && - ((params->req_line_speed == SPEED_10) || - (params->req_line_speed == SPEED_100))) { + if (vars->line_speed && + ((vars->line_speed == SPEED_10) || + (vars->line_speed == SPEED_100))) { vars->phy_flags |= PHY_SGMII_FLAG; } else { vars->phy_flags &= ~PHY_SGMII_FLAG; @@ -670,7 +671,6 @@ static u8 bnx2x_pbf_update(struct link_params *params, u32 flow_ctrl, u8 port = params->port; u32 init_crd, crd; u32 count = 1000; - u32 pause = 0; /* disable port */ REG_WR(bp, PBF_REG_DISABLE_NEW_TASK_PROC_P0 + port*4, 0x1); @@ -693,33 +693,25 @@ static u8 bnx2x_pbf_update(struct link_params *params, u32 flow_ctrl, return -EINVAL; } - if (flow_ctrl & FLOW_CTRL_RX) - pause = 1; - REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, pause); - if (pause) { + if (flow_ctrl & FLOW_CTRL_RX || + line_speed == SPEED_10 || + line_speed == SPEED_100 || + line_speed == SPEED_1000 || + line_speed == SPEED_2500) { + REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 1); /* update threshold */ REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, 0); /* update init credit */ - init_crd = 778; /* (800-18-4) */ + init_crd = 778; /* (800-18-4) */ } else { u32 thresh = (ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD)/16; - + REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 0); /* update threshold */ REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, thresh); /* update init credit */ switch (line_speed) { - case SPEED_10: - case SPEED_100: - case SPEED_1000: - init_crd = thresh + 55 - 22; - break; - - case SPEED_2500: - init_crd = thresh + 138 - 22; - break; - case SPEED_10000: init_crd = thresh + 553 - 22; break; @@ -1114,7 +1106,7 @@ static void bnx2x_set_autoneg(struct link_params *params, MDIO_COMBO_IEEE0_MII_CONTROL, ®_val); /* CL37 Autoneg Enabled */ - if (params->req_line_speed == SPEED_AUTO_NEG) + if (vars->line_speed == SPEED_AUTO_NEG) reg_val |= MDIO_COMBO_IEEO_MII_CONTROL_AN_EN; else /* CL37 Autoneg Disabled */ reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN | @@ -1132,7 +1124,7 @@ static void bnx2x_set_autoneg(struct link_params *params, MDIO_REG_BANK_SERDES_DIGITAL, MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, ®_val); reg_val &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_SIGNAL_DETECT_EN; - if (params->req_line_speed == SPEED_AUTO_NEG) + if (vars->line_speed == SPEED_AUTO_NEG) reg_val |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET; else reg_val &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET; @@ -1148,7 +1140,7 @@ static void bnx2x_set_autoneg(struct link_params *params, MDIO_REG_BANK_BAM_NEXT_PAGE, MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL, ®_val); - if (params->req_line_speed == SPEED_AUTO_NEG) { + if (vars->line_speed == SPEED_AUTO_NEG) { /* Enable BAM aneg Mode and TetonII aneg Mode */ reg_val |= (MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE | MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN); @@ -1164,7 +1156,7 @@ static void bnx2x_set_autoneg(struct link_params *params, reg_val); /* Enable Clause 73 Aneg */ - if ((params->req_line_speed == SPEED_AUTO_NEG) && + if ((vars->line_speed == SPEED_AUTO_NEG) && (SUPPORT_CL73)) { /* Enable BAM Station Manager */ @@ -1226,7 +1218,8 @@ static void bnx2x_set_autoneg(struct link_params *params, } /* program SerDes, forced speed */ -static void bnx2x_program_serdes(struct link_params *params) +static void bnx2x_program_serdes(struct link_params *params, + struct link_vars *vars) { struct bnx2x *bp = params->bp; u16 reg_val; @@ -1248,28 +1241,35 @@ static void bnx2x_program_serdes(struct link_params *params) /* program speed - needed only if the speed is greater than 1G (2.5G or 10G) */ - if (!((params->req_line_speed == SPEED_1000) || - (params->req_line_speed == SPEED_100) || - (params->req_line_speed == SPEED_10))) { - CL45_RD_OVER_CL22(bp, params->port, + CL45_RD_OVER_CL22(bp, params->port, params->phy_addr, MDIO_REG_BANK_SERDES_DIGITAL, MDIO_SERDES_DIGITAL_MISC1, ®_val); - /* clearing the speed value before setting the right speed */ - reg_val &= ~MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK; + /* clearing the speed value before setting the right speed */ + DP(NETIF_MSG_LINK, "MDIO_REG_BANK_SERDES_DIGITAL = 0x%x\n", reg_val); + + reg_val &= ~(MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK | + MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL); + + if (!((vars->line_speed == SPEED_1000) || + (vars->line_speed == SPEED_100) || + (vars->line_speed == SPEED_10))) { + reg_val |= (MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_156_25M | MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL); - if (params->req_line_speed == SPEED_10000) + if (vars->line_speed == SPEED_10000) reg_val |= MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_CX4; - if (params->req_line_speed == SPEED_13000) + if (vars->line_speed == SPEED_13000) reg_val |= MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_13G; - CL45_WR_OVER_CL22(bp, params->port, + } + + CL45_WR_OVER_CL22(bp, params->port, params->phy_addr, MDIO_REG_BANK_SERDES_DIGITAL, MDIO_SERDES_DIGITAL_MISC1, reg_val); - } + } static void bnx2x_set_brcm_cl37_advertisment(struct link_params *params) @@ -1295,48 +1295,49 @@ static void bnx2x_set_brcm_cl37_advertisment(struct link_params *params) MDIO_OVER_1G_UP3, 0); } -static void bnx2x_set_ieee_aneg_advertisment(struct link_params *params, - u32 *ieee_fc) +static void bnx2x_calc_ieee_aneg_adv(struct link_params *params, u32 *ieee_fc) { - struct bnx2x *bp = params->bp; - /* for AN, we are always publishing full duplex */ - u16 an_adv = MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX; - + *ieee_fc = MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX; /* resolve pause mode and advertisement * Please refer to Table 28B-3 of the 802.3ab-1999 spec */ switch (params->req_flow_ctrl) { case FLOW_CTRL_AUTO: - if (params->mtu <= MAX_MTU_SIZE) { - an_adv |= + if (params->req_fc_auto_adv == FLOW_CTRL_BOTH) { + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; } else { - an_adv |= + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC; } break; case FLOW_CTRL_TX: - an_adv |= + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC; break; case FLOW_CTRL_RX: case FLOW_CTRL_BOTH: - an_adv |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; break; case FLOW_CTRL_NONE: default: - an_adv |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE; + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE; break; } +} - *ieee_fc = an_adv; +static void bnx2x_set_ieee_aneg_advertisment(struct link_params *params, + u32 ieee_fc) +{ + struct bnx2x *bp = params->bp; + /* for AN, we are always publishing full duplex */ CL45_WR_OVER_CL22(bp, params->port, params->phy_addr, MDIO_REG_BANK_COMBO_IEEE0, - MDIO_COMBO_IEEE0_AUTO_NEG_ADV, an_adv); + MDIO_COMBO_IEEE0_AUTO_NEG_ADV, (u16)ieee_fc); } static void bnx2x_restart_autoneg(struct link_params *params) @@ -1382,7 +1383,8 @@ static void bnx2x_restart_autoneg(struct link_params *params) } } -static void bnx2x_initialize_sgmii_process(struct link_params *params) +static void bnx2x_initialize_sgmii_process(struct link_params *params, + struct link_vars *vars) { struct bnx2x *bp = params->bp; u16 control1; @@ -1406,7 +1408,7 @@ static void bnx2x_initialize_sgmii_process(struct link_params *params) control1); /* if forced speed */ - if (!(params->req_line_speed == SPEED_AUTO_NEG)) { + if (!(vars->line_speed == SPEED_AUTO_NEG)) { /* set speed, disable autoneg */ u16 mii_control; @@ -1419,7 +1421,7 @@ static void bnx2x_initialize_sgmii_process(struct link_params *params) MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK| MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX); - switch (params->req_line_speed) { + switch (vars->line_speed) { case SPEED_100: mii_control |= MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_100; @@ -1433,8 +1435,8 @@ static void bnx2x_initialize_sgmii_process(struct link_params *params) break; default: /* invalid speed for SGMII */ - DP(NETIF_MSG_LINK, "Invalid req_line_speed 0x%x\n", - params->req_line_speed); + DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n", + vars->line_speed); break; } @@ -1460,20 +1462,20 @@ static void bnx2x_initialize_sgmii_process(struct link_params *params) */ static void bnx2x_pause_resolve(struct link_vars *vars, u32 pause_result) -{ - switch (pause_result) { /* ASYM P ASYM P */ - case 0xb: /* 1 0 1 1 */ +{ /* LD LP */ + switch (pause_result) { /* ASYM P ASYM P */ + case 0xb: /* 1 0 1 1 */ vars->flow_ctrl = FLOW_CTRL_TX; break; - case 0xe: /* 1 1 1 0 */ + case 0xe: /* 1 1 1 0 */ vars->flow_ctrl = FLOW_CTRL_RX; break; - case 0x5: /* 0 1 0 1 */ - case 0x7: /* 0 1 1 1 */ - case 0xd: /* 1 1 0 1 */ - case 0xf: /* 1 1 1 1 */ + case 0x5: /* 0 1 0 1 */ + case 0x7: /* 0 1 1 1 */ + case 0xd: /* 1 1 0 1 */ + case 0xf: /* 1 1 1 1 */ vars->flow_ctrl = FLOW_CTRL_BOTH; break; @@ -1487,8 +1489,8 @@ static u8 bnx2x_ext_phy_resove_fc(struct link_params *params, { struct bnx2x *bp = params->bp; u8 ext_phy_addr; - u16 ld_pause; /* local */ - u16 lp_pause; /* link partner */ + u16 ld_pause; /* local */ + u16 lp_pause; /* link partner */ u16 an_complete; /* AN complete */ u16 pause_result; u8 ret = 0; @@ -1531,6 +1533,28 @@ static u8 bnx2x_ext_phy_resove_fc(struct link_params *params, DP(NETIF_MSG_LINK, "Ext PHY pause result 0x%x \n", pause_result); bnx2x_pause_resolve(vars, pause_result); + if (vars->flow_ctrl == FLOW_CTRL_NONE && + ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) { + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_FC_LD, &ld_pause); + + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_FC_LP, &lp_pause); + pause_result = (ld_pause & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) >> 5; + pause_result |= (lp_pause & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) >> 7; + + bnx2x_pause_resolve(vars, pause_result); + DP(NETIF_MSG_LINK, "Ext PHY CL37 pause result 0x%x \n", + pause_result); + } } return ret; } @@ -1573,13 +1597,10 @@ static void bnx2x_flow_ctrl_resolve(struct link_params *params, (bnx2x_ext_phy_resove_fc(params, vars))) { return; } else { - vars->flow_ctrl = params->req_flow_ctrl; - if (vars->flow_ctrl == FLOW_CTRL_AUTO) { - if (params->mtu <= MAX_MTU_SIZE) - vars->flow_ctrl = FLOW_CTRL_BOTH; - else - vars->flow_ctrl = FLOW_CTRL_TX; - } + if (params->req_flow_ctrl == FLOW_CTRL_AUTO) + vars->flow_ctrl = params->req_fc_auto_adv; + else + vars->flow_ctrl = params->req_flow_ctrl; } DP(NETIF_MSG_LINK, "flow_ctrl 0x%x\n", vars->flow_ctrl); } @@ -1709,12 +1730,12 @@ static u8 bnx2x_link_settings_status(struct link_params *params, } if (vars->flow_ctrl & FLOW_CTRL_TX) - vars->link_status |= - LINK_STATUS_TX_FLOW_CONTROL_ENABLED; + vars->link_status |= + LINK_STATUS_TX_FLOW_CONTROL_ENABLED; if (vars->flow_ctrl & FLOW_CTRL_RX) - vars->link_status |= - LINK_STATUS_RX_FLOW_CONTROL_ENABLED; + vars->link_status |= + LINK_STATUS_RX_FLOW_CONTROL_ENABLED; } else { /* link_down */ DP(NETIF_MSG_LINK, "phy link down\n"); @@ -2286,13 +2307,16 @@ static void bnx2x_ext_phy_set_pause(struct link_params *params, MDIO_AN_REG_ADV_PAUSE, &val); val &= ~MDIO_AN_REG_ADV_PAUSE_BOTH; + /* Please refer to Table 28B-3 of 802.3ab-1999 spec. */ - if (vars->ieee_fc & + if ((vars->ieee_fc & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) == MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) { val |= MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC; } - if (vars->ieee_fc & + if ((vars->ieee_fc & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) == MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) { val |= MDIO_AN_REG_ADV_PAUSE_PAUSE; @@ -2339,7 +2363,7 @@ static void bnx2x_init_internal_phy(struct link_params *params, bnx2x_set_autoneg(params, vars); /* program speed and duplex */ - bnx2x_program_serdes(params); + bnx2x_program_serdes(params, vars); } else { /* AN_mode */ DP(NETIF_MSG_LINK, "not SGMII, AN\n"); @@ -2349,7 +2373,7 @@ static void bnx2x_init_internal_phy(struct link_params *params, /* program duplex & pause advertisement (for aneg) */ bnx2x_set_ieee_aneg_advertisment(params, - &vars->ieee_fc); + vars->ieee_fc); /* enable autoneg */ bnx2x_set_autoneg(params, vars); @@ -2361,7 +2385,7 @@ static void bnx2x_init_internal_phy(struct link_params *params, } else { /* SGMII mode */ DP(NETIF_MSG_LINK, "SGMII\n"); - bnx2x_initialize_sgmii_process(params); + bnx2x_initialize_sgmii_process(params, vars); } } @@ -2481,7 +2505,7 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) ext_phy_type, ext_phy_addr, MDIO_AN_DEVAD, - MDIO_AN_REG_CL37_FD, + MDIO_AN_REG_CL37_FC_LP, 0x0020); /* Enable CL37 AN */ bnx2x_cl45_write(bp, params->port, @@ -2657,13 +2681,13 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) ext_phy_type, ext_phy_addr, MDIO_AN_DEVAD, - MDIO_AN_REG_CL37_CL73, 0x040c); + MDIO_AN_REG_CL37_FC_LD, 0x040c); /* Add support for CL37 (passive mode) II */ bnx2x_cl45_write(bp, params->port, ext_phy_type, ext_phy_addr, MDIO_AN_DEVAD, - MDIO_AN_REG_CL37_FD, 0x20); + MDIO_AN_REG_CL37_FC_LD, 0x20); /* Add support for CL37 (passive mode) III */ bnx2x_cl45_write(bp, params->port, ext_phy_type, @@ -2785,7 +2809,7 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, - struct link_vars *vars) + struct link_vars *vars) { struct bnx2x *bp = params->bp; u32 ext_phy_type; @@ -2826,6 +2850,8 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, MDIO_PMA_REG_RX_SD, &rx_sd); DP(NETIF_MSG_LINK, "8705 rx_sd 0x%x\n", rx_sd); ext_phy_link_up = (rx_sd & 0x1); + if (ext_phy_link_up) + vars->line_speed = SPEED_10000; break; case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706: @@ -3734,7 +3760,7 @@ static u8 bnx2x_link_initialize(struct link_params *params, req_line_speed*/ vars->line_speed = params->req_line_speed; - bnx2x_set_ieee_aneg_advertisment(params, &vars->ieee_fc); + bnx2x_calc_ieee_aneg_adv(params, &vars->ieee_fc); /* init ext phy and enable link state int */ non_ext_phy = ((ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) || diff --git a/drivers/net/bnx2x_link.h b/drivers/net/bnx2x_link.h index 714d37ac95d..b222552b868 100644 --- a/drivers/net/bnx2x_link.h +++ b/drivers/net/bnx2x_link.h @@ -58,11 +58,13 @@ struct link_params { u16 req_duplex; u16 req_flow_ctrl; + u16 req_fc_auto_adv; /* Should be set to TX / BOTH when + req_flow_ctrl is set to AUTO */ u16 req_line_speed; /* Also determine AutoNeg */ /* Device parameters */ u8 mac_addr[6]; - u16 mtu; + /* shmem parameters */ diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index d29f22763fe..a37549b5bc1 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -1946,7 +1946,14 @@ static u8 bnx2x_initial_phy_init(struct bnx2x *bp) u8 rc; /* Initialize link parameters structure variables */ - bp->link_params.mtu = bp->dev->mtu; + /* It is recommended to turn off RX FC for jumbo frames + for better performance */ + if (IS_E1HMF(bp)) + bp->link_params.req_fc_auto_adv = FLOW_CTRL_BOTH; + else if (bp->dev->mtu > 5000) + bp->link_params.req_fc_auto_adv = FLOW_CTRL_TX; + else + bp->link_params.req_fc_auto_adv = FLOW_CTRL_BOTH; bnx2x_acquire_phy_lock(bp); rc = bnx2x_phy_init(&bp->link_params, &bp->link_vars); diff --git a/drivers/net/bnx2x_reg.h b/drivers/net/bnx2x_reg.h index 58fbeb1cf78..5029d1e466f 100644 --- a/drivers/net/bnx2x_reg.h +++ b/drivers/net/bnx2x_reg.h @@ -4966,6 +4966,7 @@ #define EMAC_RX_MODE_PROMISCUOUS (1L<<8) #define EMAC_RX_MTU_SIZE_JUMBO_ENA (1L<<31) #define EMAC_TX_MODE_EXT_PAUSE_EN (1L<<3) +#define EMAC_TX_MODE_FLOW_EN (1L<<4) #define MISC_REGISTERS_GPIO_0 0 #define MISC_REGISTERS_GPIO_1 1 #define MISC_REGISTERS_GPIO_2 2 @@ -5615,7 +5616,8 @@ Theotherbitsarereservedandshouldbezero*/ #define MDIO_AN_REG_LINK_STATUS 0x8304 #define MDIO_AN_REG_CL37_CL73 0x8370 #define MDIO_AN_REG_CL37_AN 0xffe0 -#define MDIO_AN_REG_CL37_FD 0xffe4 +#define MDIO_AN_REG_CL37_FC_LD 0xffe4 +#define MDIO_AN_REG_CL37_FC_LP 0xffe5 #define IGU_FUNC_BASE 0x0400 -- GitLab From 17de50b7f71d176375e9d4d67ffce42482e5515f Mon Sep 17 00:00:00 2001 From: Eilon Greenstein Date: Wed, 13 Aug 2008 15:56:59 -0700 Subject: [PATCH 261/750] bnx2x: Change GPIO for any port Change GPIO for any port The set GPIO function should receive the port index to allow changing the GPIO of another port. This is needed for the common init phase (one the first driver is loaded for the chip) Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x.h | 2 +- drivers/net/bnx2x_link.c | 78 ++++++++++++++++++++++------------------ drivers/net/bnx2x_main.c | 14 ++++---- 3 files changed, 51 insertions(+), 43 deletions(-) diff --git a/drivers/net/bnx2x.h b/drivers/net/bnx2x.h index 3b09ae62335..e15ecfbfc85 100644 --- a/drivers/net/bnx2x.h +++ b/drivers/net/bnx2x.h @@ -924,7 +924,7 @@ struct bnx2x { void bnx2x_read_dmae(struct bnx2x *bp, u32 src_addr, u32 len32); void bnx2x_write_dmae(struct bnx2x *bp, dma_addr_t dma_addr, u32 dst_addr, u32 len32); -int bnx2x_set_gpio(struct bnx2x *bp, int gpio_num, u32 mode); +int bnx2x_set_gpio(struct bnx2x *bp, int gpio_num, u32 mode, u8 port); static inline u32 reg_poll(struct bnx2x *bp, u32 reg, u32 expected, int ms, int wait) diff --git a/drivers/net/bnx2x_link.c b/drivers/net/bnx2x_link.c index 36fa356c74f..c9cffa6d47b 100644 --- a/drivers/net/bnx2x_link.c +++ b/drivers/net/bnx2x_link.c @@ -1842,15 +1842,15 @@ static u8 bnx2x_emac_program(struct link_params *params, } /*****************************************************************************/ -/* External Phy section */ +/* External Phy section */ /*****************************************************************************/ -static void bnx2x_hw_reset(struct bnx2x *bp) +static void bnx2x_hw_reset(struct bnx2x *bp, u8 port) { bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_LOW); + MISC_REGISTERS_GPIO_OUTPUT_LOW, port); msleep(1); bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_HIGH); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, port); } static void bnx2x_ext_phy_reset(struct link_params *params, @@ -1879,10 +1879,11 @@ static void bnx2x_ext_phy_reset(struct link_params *params, /* Restore normal power mode*/ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_HIGH); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + params->port); /* HW reset */ - bnx2x_hw_reset(bp); + bnx2x_hw_reset(bp, params->port); bnx2x_cl45_write(bp, params->port, ext_phy_type, @@ -1894,7 +1895,8 @@ static void bnx2x_ext_phy_reset(struct link_params *params, /* Unset Low Power Mode and SW reset */ /* Restore normal power mode*/ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_HIGH); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + params->port); DP(NETIF_MSG_LINK, "XGXS 8072\n"); bnx2x_cl45_write(bp, params->port, @@ -1912,19 +1914,14 @@ static void bnx2x_ext_phy_reset(struct link_params *params, /* Restore normal power mode*/ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_HIGH); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + params->port); bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_HIGH); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + params->port); DP(NETIF_MSG_LINK, "XGXS 8073\n"); - bnx2x_cl45_write(bp, - params->port, - ext_phy_type, - ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_CTRL, - 1<<15); } break; @@ -1933,10 +1930,11 @@ static void bnx2x_ext_phy_reset(struct link_params *params, /* Restore normal power mode*/ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_HIGH); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + params->port); /* HW reset */ - bnx2x_hw_reset(bp); + bnx2x_hw_reset(bp, params->port); break; @@ -1959,7 +1957,7 @@ static void bnx2x_ext_phy_reset(struct link_params *params, case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_BCM5482: DP(NETIF_MSG_LINK, "SerDes 5482\n"); - bnx2x_hw_reset(bp); + bnx2x_hw_reset(bp, params->port); break; default: @@ -3286,12 +3284,14 @@ static void bnx2x_turn_on_ef(struct bnx2x *bp, u8 port, u8 ext_phy_addr, /* take ext phy out of reset */ bnx2x_set_gpio(bp, - MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_HIGH); + MISC_REGISTERS_GPIO_2, + MISC_REGISTERS_GPIO_HIGH, + port); bnx2x_set_gpio(bp, - MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_HIGH); + MISC_REGISTERS_GPIO_1, + MISC_REGISTERS_GPIO_HIGH, + port); /* wait for 5ms */ msleep(5); @@ -3311,13 +3311,17 @@ static void bnx2x_turn_on_ef(struct bnx2x *bp, u8 port, u8 ext_phy_addr, } } -static void bnx2x_turn_off_sf(struct bnx2x *bp) +static void bnx2x_turn_off_sf(struct bnx2x *bp, u8 port) { /* put sf to reset */ - bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, MISC_REGISTERS_GPIO_LOW); bnx2x_set_gpio(bp, - MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_LOW); + MISC_REGISTERS_GPIO_1, + MISC_REGISTERS_GPIO_LOW, + port); + bnx2x_set_gpio(bp, + MISC_REGISTERS_GPIO_2, + MISC_REGISTERS_GPIO_LOW, + port); } u8 bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded, @@ -3371,7 +3375,7 @@ u8 bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded, version[4] = '\0'; if (!driver_loaded) - bnx2x_turn_off_sf(bp); + bnx2x_turn_off_sf(bp, params->port); break; case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072: case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: @@ -4013,10 +4017,12 @@ u8 bnx2x_link_reset(struct link_params *params, struct link_vars *vars) /* HW reset */ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_LOW); + MISC_REGISTERS_GPIO_OUTPUT_LOW, + port); bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_LOW); + MISC_REGISTERS_GPIO_OUTPUT_LOW, + port); DP(NETIF_MSG_LINK, "reset external PHY\n"); } else if (ext_phy_type == @@ -4025,7 +4031,8 @@ u8 bnx2x_link_reset(struct link_params *params, struct link_vars *vars) "low power mode\n", port); bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_LOW); + MISC_REGISTERS_GPIO_OUTPUT_LOW, + port); } } /* reset the SerDes/XGXS */ @@ -4271,7 +4278,7 @@ static u8 bnx2x_sfx7101_flash_download(struct bnx2x *bp, u8 port, and issuing a reset.*/ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0, - MISC_REGISTERS_GPIO_HIGH); + MISC_REGISTERS_GPIO_HIGH, port); bnx2x_sfx7101_sp_sw_reset(bp, port, ext_phy_addr); @@ -4503,7 +4510,8 @@ static u8 bnx2x_sfx7101_flash_download(struct bnx2x *bp, u8 port, } /* DSP Remove Download Mode */ - bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0, MISC_REGISTERS_GPIO_LOW); + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0, + MISC_REGISTERS_GPIO_LOW, port); bnx2x_sfx7101_sp_sw_reset(bp, port, ext_phy_addr); @@ -4511,7 +4519,7 @@ static u8 bnx2x_sfx7101_flash_download(struct bnx2x *bp, u8 port, for (cnt = 0; cnt < 100; cnt++) msleep(5); - bnx2x_hw_reset(bp); + bnx2x_hw_reset(bp, port); for (cnt = 0; cnt < 100; cnt++) msleep(5); @@ -4586,7 +4594,7 @@ u8 bnx2x_flash_download(struct bnx2x *bp, u8 port, u32 ext_phy_config, rc = bnx2x_sfx7101_flash_download(bp, port, ext_phy_addr, data, size); if (!driver_loaded) - bnx2x_turn_off_sf(bp); + bnx2x_turn_off_sf(bp, port); break; case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT: case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE: diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index a37549b5bc1..85ea799a053 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -1788,11 +1788,11 @@ static void bnx2x_release_phy_lock(struct bnx2x *bp) mutex_unlock(&bp->port.phy_mutex); } -int bnx2x_set_gpio(struct bnx2x *bp, int gpio_num, u32 mode) +int bnx2x_set_gpio(struct bnx2x *bp, int gpio_num, u32 mode, u8 port) { /* The GPIO should be swapped if swap register is set and active */ int gpio_port = (REG_RD(bp, NIG_REG_PORT_SWAP) && - REG_RD(bp, NIG_REG_STRAP_OVERRIDE)) ^ BP_PORT(bp); + REG_RD(bp, NIG_REG_STRAP_OVERRIDE)) ^ port; int gpio_shift = gpio_num + (gpio_port ? MISC_REGISTERS_GPIO_PORT_SHIFT : 0); u32 gpio_mask = (1 << gpio_shift); @@ -1824,7 +1824,7 @@ int bnx2x_set_gpio(struct bnx2x *bp, int gpio_num, u32 mode) gpio_reg |= (gpio_mask << MISC_REGISTERS_GPIO_SET_POS); break; - case MISC_REGISTERS_GPIO_INPUT_HI_Z : + case MISC_REGISTERS_GPIO_INPUT_HI_Z: DP(NETIF_MSG_LINK, "Set GPIO %d (shift %d) -> input\n", gpio_num, gpio_shift); /* set FLOAT */ @@ -2553,12 +2553,12 @@ static inline void bnx2x_attn_int_deasserted0(struct bnx2x *bp, u32 attn) case SHARED_HW_CFG_BOARD_TYPE_BCM957710A1022G: /* Fan failure attention */ - /* The PHY reset is controled by GPIO 1 */ + /* The PHY reset is controlled by GPIO 1 */ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_LOW); - /* Low power mode is controled by GPIO 2 */ + MISC_REGISTERS_GPIO_OUTPUT_LOW, port); + /* Low power mode is controlled by GPIO 2 */ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_LOW); + MISC_REGISTERS_GPIO_OUTPUT_LOW, port); /* mark the failure */ bp->link_params.ext_phy_config &= ~PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK; -- GitLab From 6bbca910e621d82b3ca93a99af9b59eb1ff3cbcd Mon Sep 17 00:00:00 2001 From: Yaniv Rosner Date: Wed, 13 Aug 2008 15:57:28 -0700 Subject: [PATCH 262/750] bnx2x: 8073 PHY changes 8073 PHY changes The initial support we had for this PHY needs some serious changing. The major change is that this PHY should be initialized only when the first function is loaded and not for each function. The official SPI-ROM of this PHY was released and it requires some changes in the initialization code as well Signed-off-by: Yaniv Rosner Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x_link.c | 576 ++++++++++++++++++++++++++++----------- drivers/net/bnx2x_link.h | 3 + drivers/net/bnx2x_main.c | 7 + 3 files changed, 428 insertions(+), 158 deletions(-) diff --git a/drivers/net/bnx2x_link.c b/drivers/net/bnx2x_link.c index c9cffa6d47b..693efce7cda 100644 --- a/drivers/net/bnx2x_link.c +++ b/drivers/net/bnx2x_link.c @@ -2121,42 +2121,45 @@ static u8 bnx2x_bcm8073_xaui_wa(struct link_params *params) } -static void bnx2x_bcm8073_external_rom_boot(struct link_params *params) +static void bnx2x_bcm8073_external_rom_boot(struct bnx2x *bp, u8 port, + u8 ext_phy_addr) { - struct bnx2x *bp = params->bp; - u8 port = params->port; - u8 ext_phy_addr = ((params->ext_phy_config & - PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >> - PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT); - u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); - u16 fw_ver1, fw_ver2, val; - /* Need to wait 100ms after reset */ - msleep(100); - /* Boot port from external ROM */ + u16 fw_ver1, fw_ver2; + /* Boot port from external ROM */ /* EDC grst */ - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, MDIO_PMA_DEVAD, MDIO_PMA_REG_GEN_CTRL, 0x0001); /* ucode reboot and rst */ - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, MDIO_PMA_DEVAD, MDIO_PMA_REG_GEN_CTRL, 0x008c); - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, MDIO_PMA_DEVAD, MDIO_PMA_REG_MISC_CTRL1, 0x0001); /* Reset internal microprocessor */ - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, MDIO_PMA_DEVAD, MDIO_PMA_REG_GEN_CTRL, MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET); /* Release srst bit */ - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, MDIO_PMA_DEVAD, MDIO_PMA_REG_GEN_CTRL, MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP); @@ -2165,35 +2168,52 @@ static void bnx2x_bcm8073_external_rom_boot(struct link_params *params) msleep(100); /* Clear ser_boot_ctl bit */ - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, MDIO_PMA_DEVAD, MDIO_PMA_REG_MISC_CTRL1, 0x0000); - bnx2x_cl45_read(bp, port, ext_phy_type, ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_ROM_VER1, &fw_ver1); - bnx2x_cl45_read(bp, port, ext_phy_type, ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_ROM_VER2, &fw_ver2); + bnx2x_cl45_read(bp, port, PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER1, &fw_ver1); + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER2, &fw_ver2); DP(NETIF_MSG_LINK, "8073 FW version 0x%x:0x%x\n", fw_ver1, fw_ver2); - /* Only set bit 10 = 1 (Tx power down) */ - bnx2x_cl45_read(bp, port, ext_phy_type, ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_TX_POWER_DOWN, &val); +} +static void bnx2x_bcm807x_force_10G(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + u8 ext_phy_addr = ((params->ext_phy_config & + PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >> + PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT); + u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + + /* Force KR or KX */ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, MDIO_PMA_DEVAD, - MDIO_PMA_REG_TX_POWER_DOWN, (val | 1<<10)); - - msleep(600); - /* Release bit 10 (Release Tx power down) */ + MDIO_PMA_REG_CTRL, + 0x2040); bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, MDIO_PMA_DEVAD, - MDIO_PMA_REG_TX_POWER_DOWN, (val & (~(1<<10)))); - + MDIO_PMA_REG_10G_CTRL2, + 0x000b); + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_BCM_CTRL, + 0x0000); + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CTRL, + 0x0000); } - static void bnx2x_bcm8073_set_xaui_low_power_mode(struct link_params *params) { struct bnx2x *bp = params->bp; @@ -2259,32 +2279,51 @@ static void bnx2x_bcm8073_set_xaui_low_power_mode(struct link_params *params) bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, MDIO_XS_DEVAD, MDIO_XS_PLL_SEQUENCER, val); } -static void bnx2x_bcm807x_force_10G(struct link_params *params) + +static void bnx2x_8073_set_pause_cl37(struct link_params *params, + struct link_vars *vars) { + struct bnx2x *bp = params->bp; - u8 port = params->port; + u16 cl37_val; u8 ext_phy_addr = ((params->ext_phy_config & PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >> PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT); u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); - /* Force KR or KX */ - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_CTRL, - 0x2040); - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_10G_CTRL2, - 0x000b); - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_BCM_CTRL, - 0x0000); - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_FC_LD, &cl37_val); + + cl37_val &= ~MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; + /* Please refer to Table 28B-3 of 802.3ab-1999 spec. */ + + if ((vars->ieee_fc & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC) == + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC) { + cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC; + } + if ((vars->ieee_fc & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) == + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) { + cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC; + } + if ((vars->ieee_fc & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) == + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) { + cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; + } + DP(NETIF_MSG_LINK, + "Ext phy AN advertize cl37 0x%x\n", cl37_val); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, MDIO_AN_DEVAD, - MDIO_AN_REG_CTRL, - 0x0000); + MDIO_AN_REG_CL37_FC_LD, cl37_val); + msleep(500); } static void bnx2x_ext_phy_set_pause(struct link_params *params, @@ -2542,54 +2581,43 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) rx_alarm_ctrl_val = 0x400; lasi_ctrl_val = 0x0004; } else { - /* In 8073, port1 is directed through emac0 and - * port0 is directed through emac1 - */ rx_alarm_ctrl_val = (1<<2); - /*lasi_ctrl_val = 0x0005;*/ lasi_ctrl_val = 0x0004; } - /* Wait for soft reset to get cleared upto 1 sec */ - for (cnt = 0; cnt < 1000; cnt++) { - bnx2x_cl45_read(bp, params->port, - ext_phy_type, - ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_CTRL, - &ctrl); - if (!(ctrl & (1<<15))) - break; - msleep(1); - } - DP(NETIF_MSG_LINK, - "807x control reg 0x%x (after %d ms)\n", - ctrl, cnt); + /* enable LASI */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_RX_ALARM_CTRL, + rx_alarm_ctrl_val); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_LASI_CTRL, + lasi_ctrl_val); + + bnx2x_8073_set_pause_cl37(params, vars); if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072){ bnx2x_bcm8072_external_rom_boot(params); } else { - bnx2x_bcm8073_external_rom_boot(params); + /* In case of 8073 with long xaui lines, don't set the 8073 xaui low power*/ bnx2x_bcm8073_set_xaui_low_power_mode(params); } - /* enable LASI */ - bnx2x_cl45_write(bp, params->port, - ext_phy_type, - ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_RX_ALARM_CTRL, - rx_alarm_ctrl_val); - - bnx2x_cl45_write(bp, params->port, - ext_phy_type, - ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_LASI_CTRL, - lasi_ctrl_val); + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + 0xca13, + &tmp1); bnx2x_cl45_read(bp, params->port, ext_phy_type, @@ -2603,12 +2631,21 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) /* If this is forced speed, set to KR or KX * (all other are not supported) */ - if (!(params->req_line_speed == SPEED_AUTO_NEG)) { - if (params->req_line_speed == SPEED_10000) { - bnx2x_bcm807x_force_10G(params); - DP(NETIF_MSG_LINK, - "Forced speed 10G on 807X\n"); - break; + if (params->loopback_mode == LOOPBACK_EXT) { + bnx2x_bcm807x_force_10G(params); + DP(NETIF_MSG_LINK, + "Forced speed 10G on 807X\n"); + break; + } else { + bnx2x_cl45_write(bp, params->port, + ext_phy_type, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_BCM_CTRL, + 0x0002); + } + if (params->req_line_speed != SPEED_AUTO_NEG) { + if (params->req_line_speed == SPEED_10000) { + val = (1<<7); } else if (params->req_line_speed == SPEED_2500) { val = (1<<5); @@ -2623,11 +2660,14 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) val |= (1<<7); + /* Note that 2.5G works only when + used with 1G advertisment */ if (params->speed_cap_mask & - PORT_HW_CFG_SPEED_CAPABILITY_D0_1G) + (PORT_HW_CFG_SPEED_CAPABILITY_D0_1G | + PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G)) val |= (1<<5); - DP(NETIF_MSG_LINK, "807x autoneg val = 0x%x\n", val); - /*val = ((1<<5)|(1<<7));*/ + DP(NETIF_MSG_LINK, + "807x autoneg val = 0x%x\n", val); } bnx2x_cl45_write(bp, params->port, @@ -2638,20 +2678,19 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) { - /* Disable 2.5Ghz */ + bnx2x_cl45_read(bp, params->port, ext_phy_type, ext_phy_addr, MDIO_AN_DEVAD, 0x8329, &tmp1); -/* SUPPORT_SPEED_CAPABILITY - (Due to the nature of the link order, its not - possible to enable 2.5G within the autoneg - capabilities) - if (params->speed_cap_mask & - PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G) -*/ - if (params->req_line_speed == SPEED_2500) { + + if (((params->speed_cap_mask & + PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G) && + (params->req_line_speed == + SPEED_AUTO_NEG)) || + (params->req_line_speed == + SPEED_2500)) { u16 phy_ver; /* Allow 2.5G for A1 and above */ bnx2x_cl45_read(bp, params->port, @@ -2659,49 +2698,53 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) ext_phy_addr, MDIO_PMA_DEVAD, 0xc801, &phy_ver); - + DP(NETIF_MSG_LINK, "Add 2.5G\n"); if (phy_ver > 0) tmp1 |= 1; else tmp1 &= 0xfffe; - } - else + } else { + DP(NETIF_MSG_LINK, "Disable 2.5G\n"); tmp1 &= 0xfffe; + } - bnx2x_cl45_write(bp, params->port, - ext_phy_type, - ext_phy_addr, - MDIO_AN_DEVAD, + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, 0x8329, tmp1); } - /* Add support for CL37 (passive mode) I */ - bnx2x_cl45_write(bp, params->port, + + /* Add support for CL37 (passive mode) II */ + + bnx2x_cl45_read(bp, params->port, ext_phy_type, ext_phy_addr, MDIO_AN_DEVAD, - MDIO_AN_REG_CL37_FC_LD, 0x040c); - /* Add support for CL37 (passive mode) II */ + MDIO_AN_REG_CL37_FC_LD, + &tmp1); + bnx2x_cl45_write(bp, params->port, ext_phy_type, ext_phy_addr, MDIO_AN_DEVAD, - MDIO_AN_REG_CL37_FC_LD, 0x20); + MDIO_AN_REG_CL37_FC_LD, (tmp1 | + ((params->req_duplex == DUPLEX_FULL) ? + 0x20 : 0x40))); + /* Add support for CL37 (passive mode) III */ bnx2x_cl45_write(bp, params->port, ext_phy_type, ext_phy_addr, MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1000); - /* Restart autoneg */ - msleep(500); if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) { - - /* The SNR will improve about 2db by changing the + /* The SNR will improve about 2db by changing BW and FEE main tap. Rest commands are executed after link is up*/ - /* Change FFE main cursor to 5 in EDC register */ + /*Change FFE main cursor to 5 in EDC register*/ if (bnx2x_8073_is_snr_needed(params)) bnx2x_cl45_write(bp, params->port, ext_phy_type, @@ -2710,25 +2753,28 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) MDIO_PMA_REG_EDC_FFE_MAIN, 0xFB0C); - /* Enable FEC (Forware Error Correction) - Request in the AN */ - bnx2x_cl45_read(bp, params->port, - ext_phy_type, - ext_phy_addr, - MDIO_AN_DEVAD, - MDIO_AN_REG_ADV2, &tmp1); + /* Enable FEC (Forware Error Correction) + Request in the AN */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_ADV2, &tmp1); - tmp1 |= (1<<15); + tmp1 |= (1<<15); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_ADV2, tmp1); - bnx2x_cl45_write(bp, params->port, - ext_phy_type, - ext_phy_addr, - MDIO_AN_DEVAD, - MDIO_AN_REG_ADV2, tmp1); } bnx2x_ext_phy_set_pause(params, vars); + /* Restart autoneg */ + msleep(500); bnx2x_cl45_write(bp, params->port, ext_phy_type, ext_phy_addr, @@ -2910,6 +2956,8 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072: case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: { + u16 link_status = 0; + u16 an1000_status = 0; if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072) { bnx2x_cl45_read(bp, params->port, @@ -2936,14 +2984,9 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_STATUS, &val1); - bnx2x_cl45_read(bp, params->port, - ext_phy_type, - ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_LASI_STATUS, &val2); DP(NETIF_MSG_LINK, - "8703 LASI status 0x%x->0x%x\n", - val1, val2); + "8703 LASI status 0x%x\n", + val1); } /* clear the interrupt LASI status register */ @@ -2959,20 +3002,23 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, MDIO_PCS_REG_STATUS, &val1); DP(NETIF_MSG_LINK, "807x PCS status 0x%x->0x%x\n", val2, val1); - /* Check the LASI */ + /* Clear MSG-OUT */ bnx2x_cl45_read(bp, params->port, ext_phy_type, ext_phy_addr, MDIO_PMA_DEVAD, - MDIO_PMA_REG_RX_ALARM, &val2); + 0xca13, + &val1); + + /* Check the LASI */ bnx2x_cl45_read(bp, params->port, ext_phy_type, ext_phy_addr, MDIO_PMA_DEVAD, - MDIO_PMA_REG_RX_ALARM, - &val1); - DP(NETIF_MSG_LINK, "KR 0x9003 0x%x->0x%x\n", - val2, val1); + MDIO_PMA_REG_RX_ALARM, &val2); + + DP(NETIF_MSG_LINK, "KR 0x9003 0x%x\n", val2); + /* Check the link status */ bnx2x_cl45_read(bp, params->port, ext_phy_type, @@ -2995,29 +3041,29 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, DP(NETIF_MSG_LINK, "PMA_REG_STATUS=0x%x\n", val1); if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) { - u16 an1000_status = 0; + if (ext_phy_link_up && - ( - (params->req_line_speed != SPEED_10000) - )) { + ((params->req_line_speed != + SPEED_10000))) { if (bnx2x_bcm8073_xaui_wa(params) != 0) { ext_phy_link_up = 0; break; } - bnx2x_cl45_read(bp, params->port, + } + bnx2x_cl45_read(bp, params->port, ext_phy_type, ext_phy_addr, - MDIO_XS_DEVAD, + MDIO_AN_DEVAD, 0x8304, &an1000_status); - bnx2x_cl45_read(bp, params->port, + bnx2x_cl45_read(bp, params->port, ext_phy_type, ext_phy_addr, - MDIO_XS_DEVAD, + MDIO_AN_DEVAD, 0x8304, &an1000_status); - } + /* Check the link status on 1.1.2 */ bnx2x_cl45_read(bp, params->port, ext_phy_type, @@ -3033,8 +3079,8 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, "an_link_status=0x%x\n", val2, val1, an1000_status); - ext_phy_link_up = (((val1 & 4) == 4) || - (an1000_status & (1<<1))); + ext_phy_link_up = (((val1 & 4) == 4) || + (an1000_status & (1<<1))); if (ext_phy_link_up && bnx2x_8073_is_snr_needed(params)) { /* The SNR will improve about 2dbby @@ -3058,8 +3104,74 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, MDIO_PMA_REG_CDR_BANDWIDTH, 0x0333); + + } + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + 0xc820, + &link_status); + + /* Bits 0..2 --> speed detected, + bits 13..15--> link is down */ + if ((link_status & (1<<2)) && + (!(link_status & (1<<15)))) { + ext_phy_link_up = 1; + vars->line_speed = SPEED_10000; + DP(NETIF_MSG_LINK, + "port %x: External link" + " up in 10G\n", params->port); + } else if ((link_status & (1<<1)) && + (!(link_status & (1<<14)))) { + ext_phy_link_up = 1; + vars->line_speed = SPEED_2500; + DP(NETIF_MSG_LINK, + "port %x: External link" + " up in 2.5G\n", params->port); + } else if ((link_status & (1<<0)) && + (!(link_status & (1<<13)))) { + ext_phy_link_up = 1; + vars->line_speed = SPEED_1000; + DP(NETIF_MSG_LINK, + "port %x: External link" + " up in 1G\n", params->port); + } else { + ext_phy_link_up = 0; + DP(NETIF_MSG_LINK, + "port %x: External link" + " is down\n", params->port); + } + } else { + /* See if 1G link is up for the 8072 */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + 0x8304, + &an1000_status); + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + 0x8304, + &an1000_status); + if (an1000_status & (1<<1)) { + ext_phy_link_up = 1; + vars->line_speed = SPEED_1000; + DP(NETIF_MSG_LINK, + "port %x: External link" + " up in 1G\n", params->port); + } else if (ext_phy_link_up) { + ext_phy_link_up = 1; + vars->line_speed = SPEED_10000; + DP(NETIF_MSG_LINK, + "port %x: External link" + " up in 10G\n", params->port); } } + + break; } case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101: @@ -4203,6 +4315,154 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) return rc; } +static u8 bnx2x_8073_common_init_phy(struct bnx2x *bp, u32 shmem_base) +{ + u8 ext_phy_addr[PORT_MAX]; + u16 val; + s8 port; + + /* PART1 - Reset both phys */ + for (port = PORT_MAX - 1; port >= PORT_0; port--) { + /* Extract the ext phy address for the port */ + u32 ext_phy_config = REG_RD(bp, shmem_base + + offsetof(struct shmem_region, + dev_info.port_hw_config[port].external_phy_config)); + + /* disable attentions */ + bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4, + (NIG_MASK_XGXS0_LINK_STATUS | + NIG_MASK_XGXS0_LINK10G | + NIG_MASK_SERDES0_LINK_STATUS | + NIG_MASK_MI_INT)); + + ext_phy_addr[port] = + ((ext_phy_config & + PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >> + PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT); + + /* Need to take the phy out of low power mode in order + to write to access its registers */ + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, + MISC_REGISTERS_GPIO_OUTPUT_HIGH, port); + + /* Reset the phy */ + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, + 1<<15); + } + + /* Add delay of 150ms after reset */ + msleep(150); + + /* PART2 - Download firmware to both phys */ + for (port = PORT_MAX - 1; port >= PORT_0; port--) { + u16 fw_ver1; + + bnx2x_bcm8073_external_rom_boot(bp, port, + ext_phy_addr[port]); + + bnx2x_cl45_read(bp, port, PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER1, &fw_ver1); + if (fw_ver1 == 0) { + DP(NETIF_MSG_LINK, + "bnx2x_8073_common_init_phy port %x " + "fw Download failed\n", port); + return -EINVAL; + } + + /* Only set bit 10 = 1 (Tx power down) */ + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_TX_POWER_DOWN, &val); + + /* Phase1 of TX_POWER_DOWN reset */ + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_TX_POWER_DOWN, + (val | 1<<10)); + } + + /* Toggle Transmitter: Power down and then up with 600ms + delay between */ + msleep(600); + + /* PART3 - complete TX_POWER_DOWN process, and set GPIO2 back to low */ + for (port = PORT_MAX - 1; port >= PORT_0; port--) { + /* Phase2 of POWER_DOWN_RESET*/ + /* Release bit 10 (Release Tx power down) */ + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_TX_POWER_DOWN, &val); + + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_TX_POWER_DOWN, (val & (~(1<<10)))); + msleep(15); + + /* Read modify write the SPI-ROM version select register */ + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_EDC_FFE_MAIN, &val); + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_EDC_FFE_MAIN, (val | (1<<12))); + + /* set GPIO2 back to LOW */ + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, + MISC_REGISTERS_GPIO_OUTPUT_LOW, port); + } + return 0; + +} + +u8 bnx2x_common_init_phy(struct bnx2x *bp, u32 shmem_base) +{ + u8 rc = 0; + u32 ext_phy_type; + + DP(NETIF_MSG_LINK, "bnx2x_common_init_phy\n"); + + /* Read the ext_phy_type for arbitrary port(0) */ + ext_phy_type = XGXS_EXT_PHY_TYPE( + REG_RD(bp, shmem_base + + offsetof(struct shmem_region, + dev_info.port_hw_config[0].external_phy_config))); + + switch (ext_phy_type) { + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: + { + rc = bnx2x_8073_common_init_phy(bp, shmem_base); + break; + } + default: + DP(NETIF_MSG_LINK, + "bnx2x_common_init_phy: ext_phy 0x%x not required\n", + ext_phy_type); + break; + } + + return rc; +} + + + static void bnx2x_sfx7101_sp_sw_reset(struct bnx2x *bp, u8 port, u8 phy_addr) { u16 val, cnt; diff --git a/drivers/net/bnx2x_link.h b/drivers/net/bnx2x_link.h index b222552b868..80c945ca3a5 100644 --- a/drivers/net/bnx2x_link.h +++ b/drivers/net/bnx2x_link.h @@ -55,6 +55,7 @@ struct link_params { #define LOOPBACK_BMAC 2 #define LOOPBACK_XGXS_10 3 #define LOOPBACK_EXT_PHY 4 +#define LOOPBACK_EXT 5 u16 req_duplex; u16 req_flow_ctrl; @@ -166,5 +167,7 @@ u8 bnx2x_flash_download(struct bnx2x *bp, u8 port, u32 ext_phy_config, otherwise link is down*/ u8 bnx2x_test_link(struct link_params *input, struct link_vars *vars); +/* One-time initialization for external phy after power up */ +u8 bnx2x_common_init_phy(struct bnx2x *bp, u32 shmem_base); #endif /* BNX2X_LINK_H */ diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index 85ea799a053..594b08aac93 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -5377,6 +5377,13 @@ static int bnx2x_init_common(struct bnx2x *bp) ((u32 *)&tmp)[1]); } + if (!BP_NOMCP(bp)) { + bnx2x_acquire_phy_lock(bp); + bnx2x_common_init_phy(bp, bp->common.shmem_base); + bnx2x_release_phy_lock(bp); + } else + BNX2X_ERR("Bootcode is missing - can not initialize link\n"); + return 0; } -- GitLab From 345b5d52b93113d3ce82f97c2a783319fbf0fdfd Mon Sep 17 00:00:00 2001 From: Eilon Greenstein Date: Wed, 13 Aug 2008 15:58:12 -0700 Subject: [PATCH 263/750] bnx2x: 1G LED does not turn off 1G LED does not turn off The 1G LED was not switched to off when the link was lost Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x.h | 1 + drivers/net/bnx2x_link.c | 9 +++++++++ 2 files changed, 10 insertions(+) diff --git a/drivers/net/bnx2x.h b/drivers/net/bnx2x.h index e15ecfbfc85..98d6f85fdeb 100644 --- a/drivers/net/bnx2x.h +++ b/drivers/net/bnx2x.h @@ -120,6 +120,7 @@ #define SHMEM_RD(bp, field) REG_RD(bp, SHMEM_ADDR(bp, field)) #define SHMEM_WR(bp, field, val) REG_WR(bp, SHMEM_ADDR(bp, field), val) +#define EMAC_RD(bp, reg) REG_RD(bp, emac_base + reg) #define NIG_WR(reg, val) REG_WR(bp, reg, val) #define EMAC_WR(reg, val) REG_WR(bp, emac_base + reg, val) #define BMAC_WR(reg, val) REG_WR(bp, GRCBASE_NIG + bmac_addr + reg, val) diff --git a/drivers/net/bnx2x_link.c b/drivers/net/bnx2x_link.c index 693efce7cda..876a968c594 100644 --- a/drivers/net/bnx2x_link.c +++ b/drivers/net/bnx2x_link.c @@ -3769,6 +3769,8 @@ u8 bnx2x_set_led(struct bnx2x *bp, u8 port, u8 mode, u32 speed, u16 hw_led_mode, u32 chip_id) { u8 rc = 0; + u32 tmp; + u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0; DP(NETIF_MSG_LINK, "bnx2x_set_led: port %x, mode %d\n", port, mode); DP(NETIF_MSG_LINK, "speed 0x%x, hw_led_mode 0x%x\n", speed, hw_led_mode); @@ -3777,6 +3779,9 @@ u8 bnx2x_set_led(struct bnx2x *bp, u8 port, u8 mode, u32 speed, REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 0); REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, SHARED_HW_CFG_LED_MAC1); + + tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED); + EMAC_WR(EMAC_REG_EMAC_LED, (tmp | EMAC_LED_OVERRIDE)); break; case LED_MODE_OPER: @@ -3788,6 +3793,10 @@ u8 bnx2x_set_led(struct bnx2x *bp, u8 port, u8 mode, u32 speed, LED_BLINK_RATE_VAL); REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_RATE_ENA_P0 + port*4, 1); + tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED); + EMAC_WR(EMAC_REG_EMAC_LED, + (tmp & (~EMAC_LED_OVERRIDE))); + if (!CHIP_IS_E1H(bp) && ((speed == SPEED_2500) || (speed == SPEED_1000) || -- GitLab From f0e53a847a4435f3226f5e385503f792f5f99ce2 Mon Sep 17 00:00:00 2001 From: Eilon Greenstein Date: Wed, 13 Aug 2008 15:58:30 -0700 Subject: [PATCH 264/750] bnx2x: Driver info Driver info The internal FW which is downloaded by the driver should not be displayed - it is only causing confusion and it is redundant since it can be concluded from the driver version. Display only FW which is burned on the board nvram Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x_main.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index 594b08aac93..721db2957e2 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -7763,7 +7763,7 @@ static void bnx2x_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info) { struct bnx2x *bp = netdev_priv(dev); - char phy_fw_ver[PHY_FW_VER_LEN]; + u8 phy_fw_ver[PHY_FW_VER_LEN]; strcpy(info->driver, DRV_MODULE_NAME); strcpy(info->version, DRV_MODULE_VERSION); @@ -7777,11 +7777,11 @@ static void bnx2x_get_drvinfo(struct net_device *dev, bnx2x_release_phy_lock(bp); } - snprintf(info->fw_version, 32, "%d.%d.%d:%d BC:%x%s%s", - BCM_5710_FW_MAJOR_VERSION, BCM_5710_FW_MINOR_VERSION, - BCM_5710_FW_REVISION_VERSION, - BCM_5710_FW_COMPILE_FLAGS, bp->common.bc_ver, - ((phy_fw_ver[0] != '\0')? " PHY:":""), phy_fw_ver); + snprintf(info->fw_version, 32, "BC:%d.%d.%d%s%s", + (bp->common.bc_ver & 0xff0000) >> 16, + (bp->common.bc_ver & 0xff00) >> 8, + (bp->common.bc_ver & 0xff), + ((phy_fw_ver[0] != '\0') ? " PHY:" : ""), phy_fw_ver); strcpy(info->bus_info, pci_name(bp->pdev)); info->n_stats = BNX2X_NUM_STATS; info->testinfo_len = BNX2X_NUM_TESTS; -- GitLab From 3196a88a8593748bad24824ef5eb8e5aa99698c9 Mon Sep 17 00:00:00 2001 From: Eilon Greenstein Date: Wed, 13 Aug 2008 15:58:49 -0700 Subject: [PATCH 265/750] bnx2x: Minor code improvements Minor code improvements Small changes to make the code a little bit more efficient and mostly more readable: - Using unified macros for EMAC_RD/WR which looks like normal REG_RD/WR - Removing the NIG_WR since it did nothing and was only confusing - On bnx2x_panic_dump, print only the used parts of the rings - define parameters only on the branch they are needed and not at the beginning of the function - using NETIF_MSG_INTR and not private BNX2X_MSG_SP for debug prints Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x.h | 23 ++++++------- drivers/net/bnx2x_link.c | 57 ++++++++++++++++---------------- drivers/net/bnx2x_main.c | 70 +++++++++++++++++++--------------------- 3 files changed, 72 insertions(+), 78 deletions(-) diff --git a/drivers/net/bnx2x.h b/drivers/net/bnx2x.h index 98d6f85fdeb..80f5179d636 100644 --- a/drivers/net/bnx2x.h +++ b/drivers/net/bnx2x.h @@ -121,16 +121,7 @@ #define SHMEM_WR(bp, field, val) REG_WR(bp, SHMEM_ADDR(bp, field), val) #define EMAC_RD(bp, reg) REG_RD(bp, emac_base + reg) -#define NIG_WR(reg, val) REG_WR(bp, reg, val) -#define EMAC_WR(reg, val) REG_WR(bp, emac_base + reg, val) -#define BMAC_WR(reg, val) REG_WR(bp, GRCBASE_NIG + bmac_addr + reg, val) - - -#define for_each_queue(bp, var) for (var = 0; var < bp->num_queues; var++) - -#define for_each_nondefault_queue(bp, var) \ - for (var = 1; var < bp->num_queues; var++) -#define is_multi(bp) (bp->num_queues > 1) +#define EMAC_WR(bp, reg, val) REG_WR(bp, emac_base + reg, val) /* fast path */ @@ -815,9 +806,6 @@ struct bnx2x { #define BP_FUNC(bp) (bp->func) #define BP_E1HVN(bp) (bp->func >> 1) #define BP_L_ID(bp) (BP_E1HVN(bp) << 2) -/* assorted E1HVN */ -#define IS_E1HMF(bp) (bp->e1hmf != 0) -#define BP_MAX_QUEUES(bp) (IS_E1HMF(bp) ? 4 : 16) int pm_cap; int pcie_cap; @@ -842,6 +830,7 @@ struct bnx2x { u32 mf_config; u16 e1hov; u8 e1hmf; +#define IS_E1HMF(bp) (bp->e1hmf != 0) u8 wol; @@ -872,6 +861,7 @@ struct bnx2x { #define BNX2X_STATE_ERROR 0xf000 int num_queues; +#define BP_MAX_QUEUES(bp) (IS_E1HMF(bp) ? 4 : 16) u32 rx_mode; #define BNX2X_RX_MODE_NONE 0 @@ -922,6 +912,13 @@ struct bnx2x { }; +#define for_each_queue(bp, var) for (var = 0; var < bp->num_queues; var++) + +#define for_each_nondefault_queue(bp, var) \ + for (var = 1; var < bp->num_queues; var++) +#define is_multi(bp) (bp->num_queues > 1) + + void bnx2x_read_dmae(struct bnx2x *bp, u32 src_addr, u32 len32); void bnx2x_write_dmae(struct bnx2x *bp, dma_addr_t dma_addr, u32 dst_addr, u32 len32); diff --git a/drivers/net/bnx2x_link.c b/drivers/net/bnx2x_link.c index 876a968c594..d7398a34f93 100644 --- a/drivers/net/bnx2x_link.c +++ b/drivers/net/bnx2x_link.c @@ -31,7 +31,7 @@ /********************************************************/ #define SUPPORT_CL73 0 /* Currently no */ -#define ETH_HLEN 14 +#define ETH_HLEN 14 #define ETH_OVREHEAD (ETH_HLEN + 8)/* 8 for CRC + VLAN*/ #define ETH_MIN_PACKET_SIZE 60 #define ETH_MAX_PACKET_SIZE 1500 @@ -40,7 +40,7 @@ #define BMAC_CONTROL_RX_ENABLE 2 /***********************************************************/ -/* Shortcut definitions */ +/* Shortcut definitions */ /***********************************************************/ #define NIG_STATUS_XGXS0_LINK10G \ @@ -79,12 +79,12 @@ #define AUTONEG_CL37 SHARED_HW_CFG_AN_ENABLE_CL37 #define AUTONEG_CL73 SHARED_HW_CFG_AN_ENABLE_CL73 -#define AUTONEG_BAM SHARED_HW_CFG_AN_ENABLE_BAM -#define AUTONEG_PARALLEL \ +#define AUTONEG_BAM SHARED_HW_CFG_AN_ENABLE_BAM +#define AUTONEG_PARALLEL \ SHARED_HW_CFG_AN_ENABLE_PARALLEL_DETECTION -#define AUTONEG_SGMII_FIBER_AUTODET \ +#define AUTONEG_SGMII_FIBER_AUTODET \ SHARED_HW_CFG_AN_EN_SGMII_FIBER_AUTO_DETECT -#define AUTONEG_REMOTE_PHY SHARED_HW_CFG_AN_ENABLE_REMOTE_PHY +#define AUTONEG_REMOTE_PHY SHARED_HW_CFG_AN_ENABLE_REMOTE_PHY #define GP_STATUS_PAUSE_RSOLUTION_TXSIDE \ MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_TXSIDE @@ -201,11 +201,10 @@ static void bnx2x_emac_init(struct link_params *params, /* init emac - use read-modify-write */ /* self clear reset */ val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE); - EMAC_WR(EMAC_REG_EMAC_MODE, (val | EMAC_MODE_RESET)); + EMAC_WR(bp, EMAC_REG_EMAC_MODE, (val | EMAC_MODE_RESET)); timeout = 200; - do - { + do { val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE); DP(NETIF_MSG_LINK, "EMAC reset reg is %u\n", val); if (!timeout) { @@ -213,18 +212,18 @@ static void bnx2x_emac_init(struct link_params *params, return; } timeout--; - }while (val & EMAC_MODE_RESET); + } while (val & EMAC_MODE_RESET); /* Set mac address */ val = ((params->mac_addr[0] << 8) | params->mac_addr[1]); - EMAC_WR(EMAC_REG_EMAC_MAC_MATCH, val); + EMAC_WR(bp, EMAC_REG_EMAC_MAC_MATCH, val); val = ((params->mac_addr[2] << 24) | (params->mac_addr[3] << 16) | (params->mac_addr[4] << 8) | params->mac_addr[5]); - EMAC_WR(EMAC_REG_EMAC_MAC_MATCH + 4, val); + EMAC_WR(bp, EMAC_REG_EMAC_MAC_MATCH + 4, val); } static u8 bnx2x_emac_enable(struct link_params *params, @@ -285,7 +284,7 @@ static u8 bnx2x_emac_enable(struct link_params *params, if (CHIP_REV_IS_SLOW(bp)) { /* config GMII mode */ val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE); - EMAC_WR(EMAC_REG_EMAC_MODE, + EMAC_WR(bp, EMAC_REG_EMAC_MODE, (val | EMAC_MODE_PORT_GMII)); } else { /* ASIC */ /* pause enable/disable */ @@ -309,7 +308,7 @@ static u8 bnx2x_emac_enable(struct link_params *params, /* KEEP_VLAN_TAG, promiscuous */ val = REG_RD(bp, emac_base + EMAC_REG_EMAC_RX_MODE); val |= EMAC_RX_MODE_KEEP_VLAN_TAG | EMAC_RX_MODE_PROMISCUOUS; - EMAC_WR(EMAC_REG_EMAC_RX_MODE, val); + EMAC_WR(bp, EMAC_REG_EMAC_RX_MODE, val); /* Set Loopback */ val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE); @@ -317,10 +316,10 @@ static u8 bnx2x_emac_enable(struct link_params *params, val |= 0x810; else val &= ~0x810; - EMAC_WR(EMAC_REG_EMAC_MODE, val); + EMAC_WR(bp, EMAC_REG_EMAC_MODE, val); /* enable emac for jumbo packets */ - EMAC_WR(EMAC_REG_EMAC_RX_MTU_SIZE, + EMAC_WR(bp, EMAC_REG_EMAC_RX_MTU_SIZE, (EMAC_RX_MTU_SIZE_JUMBO_ENA | (ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD))); @@ -646,7 +645,7 @@ static void bnx2x_bmac_rx_disable(struct bnx2x *bp, u8 port) u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM : NIG_REG_INGRESS_BMAC0_MEM; u32 wb_data[2]; - u32 nig_bmac_enable = REG_RD(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4); + u32 nig_bmac_enable = REG_RD(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4); /* Only if the bmac is out of reset */ if (REG_RD(bp, MISC_REG_RESET_REG_2) & @@ -1036,7 +1035,7 @@ static void bnx2x_set_swap_lanes(struct link_params *params) } static void bnx2x_set_parallel_detection(struct link_params *params, - u8 phy_flags) + u8 phy_flags) { struct bnx2x *bp = params->bp; u16 control2; @@ -1489,8 +1488,8 @@ static u8 bnx2x_ext_phy_resove_fc(struct link_params *params, { struct bnx2x *bp = params->bp; u8 ext_phy_addr; - u16 ld_pause; /* local */ - u16 lp_pause; /* link partner */ + u16 ld_pause; /* local */ + u16 lp_pause; /* link partner */ u16 an_complete; /* AN complete */ u16 pause_result; u8 ret = 0; @@ -1565,8 +1564,8 @@ static void bnx2x_flow_ctrl_resolve(struct link_params *params, u32 gp_status) { struct bnx2x *bp = params->bp; - u16 ld_pause; /* local driver */ - u16 lp_pause; /* link partner */ + u16 ld_pause; /* local driver */ + u16 lp_pause; /* link partner */ u16 pause_result; vars->flow_ctrl = FLOW_CTRL_NONE; @@ -1611,6 +1610,7 @@ static u8 bnx2x_link_settings_status(struct link_params *params, u32 gp_status) { struct bnx2x *bp = params->bp; + u8 rc = 0; vars->link_status = 0; @@ -3303,7 +3303,7 @@ static void bnx2x_link_int_enable(struct link_params *params) * link management */ static void bnx2x_link_int_ack(struct link_params *params, - struct link_vars *vars, u16 is_10g) + struct link_vars *vars, u8 is_10g) { struct bnx2x *bp = params->bp; u8 port = params->port; @@ -3781,7 +3781,7 @@ u8 bnx2x_set_led(struct bnx2x *bp, u8 port, u8 mode, u32 speed, SHARED_HW_CFG_LED_MAC1); tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED); - EMAC_WR(EMAC_REG_EMAC_LED, (tmp | EMAC_LED_OVERRIDE)); + EMAC_WR(bp, EMAC_REG_EMAC_LED, (tmp | EMAC_LED_OVERRIDE)); break; case LED_MODE_OPER: @@ -3794,7 +3794,7 @@ u8 bnx2x_set_led(struct bnx2x *bp, u8 port, u8 mode, u32 speed, REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_RATE_ENA_P0 + port*4, 1); tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED); - EMAC_WR(EMAC_REG_EMAC_LED, + EMAC_WR(bp, EMAC_REG_EMAC_LED, (tmp & (~EMAC_LED_OVERRIDE))); if (!CHIP_IS_E1H(bp) && @@ -3917,7 +3917,7 @@ u8 bnx2x_phy_init(struct link_params *params, struct link_vars *vars) struct bnx2x *bp = params->bp; u32 val; - DP(NETIF_MSG_LINK, "Phy Initialization started\n"); + DP(NETIF_MSG_LINK, "Phy Initialization started \n"); DP(NETIF_MSG_LINK, "req_speed = %d, req_flowctrl=%d\n", params->req_line_speed, params->req_flow_ctrl); vars->link_status = 0; @@ -3933,6 +3933,7 @@ u8 bnx2x_phy_init(struct link_params *params, struct link_vars *vars) else vars->phy_flags = PHY_XGXS_FLAG; + /* disable attentions */ bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + params->port*4, (NIG_MASK_XGXS0_LINK_STATUS | @@ -4542,7 +4543,7 @@ static u8 bnx2x_sfx7101_flash_download(struct bnx2x *bp, u8 port, size = MAX_APP_SIZE+HEADER_SIZE; } DP(NETIF_MSG_LINK, "File version is %c%c\n", data[0x14e], data[0x14f]); - DP(NETIF_MSG_LINK, " %c%c\n", data[0x150], data[0x151]); + DP(NETIF_MSG_LINK, " %c%c\n", data[0x150], data[0x151]); /* Put the DSP in download mode by setting FLASH_CFG[2] to 1 and issuing a reset.*/ @@ -4824,7 +4825,7 @@ static u8 bnx2x_sfx7101_flash_download(struct bnx2x *bp, u8 port, MDIO_PMA_REG_7101_VER2, &image_revision2); - if (data[0x14e] != (image_revision2&0xFF) || + if (data[0x14e] != (image_revision2&0xFF) || data[0x14f] != ((image_revision2&0xFF00)>>8) || data[0x150] != (image_revision1&0xFF) || data[0x151] != ((image_revision1&0xFF00)>>8)) { diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index 721db2957e2..d3c4c1ed07e 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -555,8 +555,8 @@ static void bnx2x_panic_dump(struct bnx2x *bp) j, rx_bd[1], rx_bd[0], sw_bd->skb); } - start = 0; - end = RX_SGE_CNT*NUM_RX_SGE_PAGES; + start = RX_SGE(fp->rx_sge_prod); + end = RX_SGE(fp->last_max_sge); for (j = start; j < end; j++) { u32 *rx_sge = (u32 *)&fp->rx_sge_ring[j]; struct sw_rx_page *sw_page = &fp->rx_page_ring[j]; @@ -885,6 +885,7 @@ static void bnx2x_tx_int(struct bnx2x_fastpath *fp, int work) } } + static void bnx2x_sp_event(struct bnx2x_fastpath *fp, union eth_rx_cqe *rr_cqe) { @@ -940,6 +941,7 @@ static void bnx2x_sp_event(struct bnx2x_fastpath *fp, bnx2x_fp(bp, cid, state) = BNX2X_FP_STATE_CLOSED; break; + case (RAMROD_CMD_ID_ETH_SET_MAC | BNX2X_STATE_OPEN): case (RAMROD_CMD_ID_ETH_SET_MAC | BNX2X_STATE_DIAG): DP(NETIF_MSG_IFUP, "got set mac ramrod\n"); @@ -1370,7 +1372,6 @@ static int bnx2x_rx_int(struct bnx2x_fastpath *fp, int budget) u16 bd_cons, bd_prod, bd_prod_fw, comp_ring_cons; u16 hw_comp_cons, sw_comp_cons, sw_comp_prod; int rx_pkt = 0; - u16 queue; #ifdef BNX2X_STOP_ON_ERROR if (unlikely(bp->panic)) @@ -1436,7 +1437,7 @@ static int bnx2x_rx_int(struct bnx2x_fastpath *fp, int budget) if ((!fp->disable_tpa) && (TPA_TYPE(cqe_fp_flags) != (TPA_TYPE_START | TPA_TYPE_END))) { - queue = cqe->fast_path_cqe.queue_index; + u16 queue = cqe->fast_path_cqe.queue_index; if (TPA_TYPE(cqe_fp_flags) == TPA_TYPE_START) { DP(NETIF_MSG_RX_STATUS, @@ -1635,17 +1636,17 @@ static irqreturn_t bnx2x_interrupt(int irq, void *dev_instance) } DP(NETIF_MSG_INTR, "got an interrupt status %u\n", status); -#ifdef BNX2X_STOP_ON_ERROR - if (unlikely(bp->panic)) - return IRQ_HANDLED; -#endif - /* Return here if interrupt is disabled */ if (unlikely(atomic_read(&bp->intr_sem) != 0)) { DP(NETIF_MSG_INTR, "called but intr_sem not 0, returning\n"); return IRQ_HANDLED; } +#ifdef BNX2X_STOP_ON_ERROR + if (unlikely(bp->panic)) + return IRQ_HANDLED; +#endif + mask = 0x2 << bp->fp[0].sb_id; if (status & mask) { struct bnx2x_fastpath *fp = &bp->fp[0]; @@ -2827,7 +2828,7 @@ static void bnx2x_sp_task(struct work_struct *work) /* Return here if interrupt is disabled */ if (unlikely(atomic_read(&bp->intr_sem) != 0)) { - DP(BNX2X_MSG_SP, "called but intr_sem not 0, returning\n"); + DP(NETIF_MSG_INTR, "called but intr_sem not 0, returning\n"); return; } @@ -2835,7 +2836,7 @@ static void bnx2x_sp_task(struct work_struct *work) /* if (status == 0) */ /* BNX2X_ERR("spurious slowpath interrupt!\n"); */ - DP(BNX2X_MSG_SP, "got a slowpath interrupt (updated %x)\n", status); + DP(NETIF_MSG_INTR, "got a slowpath interrupt (updated %x)\n", status); /* HW attentions */ if (status & 0x1) @@ -2865,7 +2866,7 @@ static irqreturn_t bnx2x_msix_sp_int(int irq, void *dev_instance) /* Return here if interrupt is disabled */ if (unlikely(atomic_read(&bp->intr_sem) != 0)) { - DP(BNX2X_MSG_SP, "called but intr_sem not 0, returning\n"); + DP(NETIF_MSG_INTR, "called but intr_sem not 0, returning\n"); return IRQ_HANDLED; } @@ -4563,7 +4564,7 @@ static void bnx2x_set_storm_rx_mode(struct bnx2x *bp) int func = BP_FUNC(bp); int i; - DP(NETIF_MSG_RX_STATUS, "rx mode is %d\n", mode); + DP(NETIF_MSG_IFUP, "rx mode %d mask 0x%x\n", mode, mask); switch (mode) { case BNX2X_RX_MODE_NONE: /* no Rx */ @@ -4922,7 +4923,7 @@ static int bnx2x_int_mem_test(struct bnx2x *bp) REG_WR(bp, TSDM_REG_ENABLE_IN1, 0x0); REG_WR(bp, TCM_REG_PRS_IFEN, 0x0); REG_WR(bp, CFC_REG_DEBUG0, 0x1); - NIG_WR(NIG_REG_PRS_REQ_IN_EN, 0x0); + REG_WR(bp, NIG_REG_PRS_REQ_IN_EN, 0x0); /* Write 0 to parser credits for CFC search request */ REG_WR(bp, PRS_REG_CFC_SEARCH_INITIAL_CREDIT, 0x0); @@ -4977,7 +4978,7 @@ static int bnx2x_int_mem_test(struct bnx2x *bp) REG_WR(bp, TSDM_REG_ENABLE_IN1, 0x0); REG_WR(bp, TCM_REG_PRS_IFEN, 0x0); REG_WR(bp, CFC_REG_DEBUG0, 0x1); - NIG_WR(NIG_REG_PRS_REQ_IN_EN, 0x0); + REG_WR(bp, NIG_REG_PRS_REQ_IN_EN, 0x0); /* Write 0 to parser credits for CFC search request */ REG_WR(bp, PRS_REG_CFC_SEARCH_INITIAL_CREDIT, 0x0); @@ -5044,7 +5045,7 @@ static int bnx2x_int_mem_test(struct bnx2x *bp) REG_WR(bp, TSDM_REG_ENABLE_IN1, 0x7fffffff); REG_WR(bp, TCM_REG_PRS_IFEN, 0x1); REG_WR(bp, CFC_REG_DEBUG0, 0x0); - NIG_WR(NIG_REG_PRS_REQ_IN_EN, 0x1); + REG_WR(bp, NIG_REG_PRS_REQ_IN_EN, 0x1); DP(NETIF_MSG_HW, "done\n"); @@ -5133,11 +5134,6 @@ static int bnx2x_init_common(struct bnx2x *bp) REG_WR(bp, PXP2_REG_RD_CDURD_SWAP_MODE, 1); #endif -#ifndef BCM_ISCSI - /* set NIC mode */ - REG_WR(bp, PRS_REG_NIC_MODE, 1); -#endif - REG_WR(bp, PXP2_REG_RQ_CDU_P_SIZE, 2); #ifdef BCM_ISCSI REG_WR(bp, PXP2_REG_RQ_TM_P_SIZE, 5); @@ -5207,6 +5203,8 @@ static int bnx2x_init_common(struct bnx2x *bp) } bnx2x_init_block(bp, PRS_COMMON_START, PRS_COMMON_END); + /* set NIC mode */ + REG_WR(bp, PRS_REG_NIC_MODE, 1); if (CHIP_IS_E1H(bp)) REG_WR(bp, PRS_REG_E1HOV_MODE, IS_E1HMF(bp)); @@ -6034,8 +6032,8 @@ static int bnx2x_req_msix_irqs(struct bnx2x *bp) bnx2x_msix_fp_int, 0, bp->dev->name, &bp->fp[i]); if (rc) { - BNX2X_ERR("request fp #%d irq failed rc %d\n", - i + offset, rc); + BNX2X_ERR("request fp #%d irq failed rc -%d\n", + i + offset, -rc); bnx2x_free_msix_irqs(bp); return -EBUSY; } @@ -6237,7 +6235,6 @@ static int bnx2x_nic_load(struct bnx2x *bp, int load_mode) { u32 load_code; int i, rc; - #ifdef BNX2X_STOP_ON_ERROR if (unlikely(bp->panic)) return -EPERM; @@ -6444,8 +6441,7 @@ load_int_disable: /* Free SKBs, SGEs, TPA pool and driver internals */ bnx2x_free_skbs(bp); for_each_queue(bp, i) - bnx2x_free_rx_sge_range(bp, bp->fp + i, - RX_SGE_CNT*NUM_RX_SGE_PAGES); + bnx2x_free_rx_sge_range(bp, bp->fp + i, NUM_RX_SGE); load_error: bnx2x_free_mem(bp); @@ -6683,11 +6679,11 @@ static int bnx2x_nic_unload(struct bnx2x *bp, int unload_mode) u8 entry = (BP_E1HVN(bp) + 1)*8; val = (mac_addr[0] << 8) | mac_addr[1]; - EMAC_WR(EMAC_REG_EMAC_MAC_MATCH + entry, val); + EMAC_WR(bp, EMAC_REG_EMAC_MAC_MATCH + entry, val); val = (mac_addr[2] << 24) | (mac_addr[3] << 16) | (mac_addr[4] << 8) | mac_addr[5]; - EMAC_WR(EMAC_REG_EMAC_MAC_MATCH + entry + 4, val); + EMAC_WR(bp, EMAC_REG_EMAC_MAC_MATCH + entry + 4, val); reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_EN; @@ -6773,8 +6769,7 @@ unload_error: /* Free SKBs, SGEs, TPA pool and driver internals */ bnx2x_free_skbs(bp); for_each_queue(bp, i) - bnx2x_free_rx_sge_range(bp, bp->fp + i, - RX_SGE_CNT*NUM_RX_SGE_PAGES); + bnx2x_free_rx_sge_range(bp, bp->fp + i, NUM_RX_SGE); bnx2x_free_mem(bp); bp->state = BNX2X_STATE_CLOSED; @@ -7411,9 +7406,8 @@ static int __devinit bnx2x_get_hwinfo(struct bnx2x *bp) bp->mf_config = SHMEM_RD(bp, mf_cfg.func_mf_config[func].config); - val = - (SHMEM_RD(bp, mf_cfg.func_mf_config[func].e1hov_tag) & - FUNC_MF_CFG_E1HOV_TAG_MASK); + val = (SHMEM_RD(bp, mf_cfg.func_mf_config[func].e1hov_tag) & + FUNC_MF_CFG_E1HOV_TAG_MASK); if (val != FUNC_MF_CFG_E1HOV_TAG_DEFAULT) { bp->e1hov = val; @@ -8368,7 +8362,7 @@ static int bnx2x_set_pauseparam(struct net_device *dev, if (epause->autoneg) { if (!(bp->port.supported & SUPPORTED_Autoneg)) { - DP(NETIF_MSG_LINK, "Autoneg not supported\n"); + DP(NETIF_MSG_LINK, "autoneg not supported\n"); return -EINVAL; } @@ -9536,7 +9530,8 @@ static int bnx2x_start_xmit(struct sk_buff *skb, struct net_device *dev) tx_bd->bd_flags.as_bitfield = ETH_TX_BD_FLAGS_START_BD; tx_bd->general_data = (UNICAST_ADDRESS << ETH_TX_BD_ETH_ADDR_TYPE_SHIFT); - tx_bd->general_data |= 1; /* header nbd */ + /* header nbd */ + tx_bd->general_data |= (1 << ETH_TX_BD_HDR_NBDS_SHIFT); /* remember the first BD of the packet */ tx_buf->first_bd = fp->tx_bd_prod; @@ -9898,6 +9893,7 @@ static int bnx2x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) { struct mii_ioctl_data *data = if_mii(ifr); struct bnx2x *bp = netdev_priv(dev); + int port = BP_PORT(bp); int err; switch (cmd) { @@ -9913,7 +9909,7 @@ static int bnx2x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) return -EAGAIN; mutex_lock(&bp->port.phy_mutex); - err = bnx2x_cl45_read(bp, BP_PORT(bp), 0, bp->port.phy_addr, + err = bnx2x_cl45_read(bp, port, 0, bp->port.phy_addr, DEFAULT_PHY_DEV_ADDR, (data->reg_num & 0x1f), &mii_regval); data->val_out = mii_regval; @@ -9929,7 +9925,7 @@ static int bnx2x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) return -EAGAIN; mutex_lock(&bp->port.phy_mutex); - err = bnx2x_cl45_write(bp, BP_PORT(bp), 0, bp->port.phy_addr, + err = bnx2x_cl45_write(bp, port, 0, bp->port.phy_addr, DEFAULT_PHY_DEV_ADDR, (data->reg_num & 0x1f), data->val_in); mutex_unlock(&bp->port.phy_mutex); -- GitLab From 3347162995d23bc13f6f99c02ae89814babcaec2 Mon Sep 17 00:00:00 2001 From: Eilon Greenstein Date: Wed, 13 Aug 2008 15:59:08 -0700 Subject: [PATCH 266/750] bnx2x: Spelling mistakes Spelling mistakes Spelling has to L's in it... Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x.h | 10 +++++----- drivers/net/bnx2x_hsi.h | 16 ++++++++-------- drivers/net/bnx2x_init.h | 6 +++--- drivers/net/bnx2x_link.h | 4 ++-- drivers/net/bnx2x_main.c | 24 ++++++++++++------------ drivers/net/bnx2x_reg.h | 18 +++++++++--------- 6 files changed, 39 insertions(+), 39 deletions(-) diff --git a/drivers/net/bnx2x.h b/drivers/net/bnx2x.h index 80f5179d636..33437e5bcec 100644 --- a/drivers/net/bnx2x.h +++ b/drivers/net/bnx2x.h @@ -155,7 +155,7 @@ struct sw_rx_page { #define NUM_RX_SGE_PAGES 2 #define RX_SGE_CNT (BCM_PAGE_SIZE / sizeof(struct eth_rx_sge)) #define MAX_RX_SGE_CNT (RX_SGE_CNT - 2) -/* RX_SGE_CNT is promissed to be a power of 2 */ +/* RX_SGE_CNT is promised to be a power of 2 */ #define RX_SGE_MASK (RX_SGE_CNT - 1) #define NUM_RX_SGE (RX_SGE_CNT * NUM_RX_SGE_PAGES) #define MAX_RX_SGE (NUM_RX_SGE - 1) @@ -317,7 +317,7 @@ struct bnx2x_fastpath { #define RCQ_BD(x) ((x) & MAX_RCQ_BD) -/* This is needed for determening of last_max */ +/* This is needed for determining of last_max */ #define SUB_S16(a, b) (s16)((s16)(a) - (s16)(b)) #define __SGE_MASK_SET_BIT(el, bit) \ @@ -784,7 +784,7 @@ struct bnx2x { u8 stats_pending; u8 set_mac_pending; - /* End of fileds used in the performance code paths */ + /* End of fields used in the performance code paths */ int panic; int msglevel; @@ -1024,10 +1024,10 @@ static inline u32 reg_poll(struct bnx2x *bp, u32 reg, u32 expected, int ms, /* resolution of the rate shaping timer - 100 usec */ #define RS_PERIODIC_TIMEOUT_USEC 100 /* resolution of fairness algorithm in usecs - - coefficient for clauclating the actuall t fair */ + coefficient for calculating the actual t fair */ #define T_FAIR_COEF 10000000 /* number of bytes in single QM arbitration cycle - - coeffiecnt for calculating the fairness timer */ + coefficient for calculating the fairness timer */ #define QM_ARB_BYTES 40000 #define FAIR_MEM 2 diff --git a/drivers/net/bnx2x_hsi.h b/drivers/net/bnx2x_hsi.h index d3e8198d7db..efd764427fa 100644 --- a/drivers/net/bnx2x_hsi.h +++ b/drivers/net/bnx2x_hsi.h @@ -1268,7 +1268,7 @@ struct doorbell { /* - * IGU driver acknowlegement register + * IGU driver acknowledgement register */ struct igu_ack_register { #if defined(__BIG_ENDIAN) @@ -1882,7 +1882,7 @@ struct timers_block_context { }; /* - * structure for easy accessability to assembler + * structure for easy accessibility to assembler */ struct eth_tx_bd_flags { u8 as_bitfield; @@ -2044,7 +2044,7 @@ struct eth_context { /* - * ethernet doorbell + * Ethernet doorbell */ struct eth_tx_doorbell { #if defined(__BIG_ENDIAN) @@ -2256,7 +2256,7 @@ struct ramrod_data { }; /* - * union for ramrod data for ethernet protocol (CQE) (force size of 16 bits) + * union for ramrod data for Ethernet protocol (CQE) (force size of 16 bits) */ union eth_ramrod_data { struct ramrod_data general; @@ -2330,7 +2330,7 @@ struct spe_hdr { }; /* - * ethernet slow path element + * Ethernet slow path element */ union eth_specific_data { u8 protocol_data[8]; @@ -2343,7 +2343,7 @@ union eth_specific_data { }; /* - * ethernet slow path element + * Ethernet slow path element */ struct eth_spe { struct spe_hdr hdr; @@ -2615,7 +2615,7 @@ struct tstorm_eth_rx_producers { /* - * common flag to indicate existance of TPA. + * common flag to indicate existence of TPA. */ struct tstorm_eth_tpa_exist { #if defined(__BIG_ENDIAN) @@ -2765,7 +2765,7 @@ struct tstorm_common_stats { }; /* - * Eth statistics query sturcture for the eth_stats_quesry ramrod + * Eth statistics query structure for the eth_stats_query ramrod */ struct eth_stats_query { struct xstorm_common_stats xstorm_common; diff --git a/drivers/net/bnx2x_init.h b/drivers/net/bnx2x_init.h index 4c7750789b6..f62891bf757 100644 --- a/drivers/net/bnx2x_init.h +++ b/drivers/net/bnx2x_init.h @@ -208,7 +208,7 @@ static void bnx2x_init_wr_64(struct bnx2x *bp, u32 addr, const u32 *data, /********************************************************* There are different blobs for each PRAM section. In addition, each blob write operation is divided into a few operations - in order to decrease the amount of phys. contigious buffer needed. + in order to decrease the amount of phys. contiguous buffer needed. Thus, when we select a blob the address may be with some offset from the beginning of PRAM section. The same holds for the INT_TABLE sections. @@ -336,7 +336,7 @@ static void bnx2x_init_block(struct bnx2x *bp, u32 op_start, u32 op_end) len = op->str_wr.data_len; data = data_base + op->str_wr.data_off; - /* carefull! it must be in order */ + /* careful! it must be in order */ if (unlikely(op_type > OP_WB)) { /* If E1 only */ @@ -740,7 +740,7 @@ static u8 calc_crc8(u32 data, u8 crc) return crc_res; } -/* regiesers addresses are not in order +/* registers addresses are not in order so these arrays help simplify the code */ static const int cm_start[E1H_FUNC_MAX][9] = { {MISC_FUNC0_START, TCM_FUNC0_START, UCM_FUNC0_START, CCM_FUNC0_START, diff --git a/drivers/net/bnx2x_link.h b/drivers/net/bnx2x_link.h index 80c945ca3a5..86d54a17b41 100644 --- a/drivers/net/bnx2x_link.h +++ b/drivers/net/bnx2x_link.h @@ -143,7 +143,7 @@ u8 bnx2x_cl45_write(struct bnx2x *bp, u8 port, u32 ext_phy_type, u8 phy_addr, u8 devad, u16 reg, u16 val); /* Reads the link_status from the shmem, - and update the link vars accordinaly */ + and update the link vars accordingly */ void bnx2x_link_status_update(struct link_params *input, struct link_vars *output); /* returns string representing the fw_version of the external phy */ @@ -152,7 +152,7 @@ u8 bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded, /* Set/Unset the led Basically, the CLC takes care of the led for the link, but in case one needs - to set/unset the led unnatually, set the "mode" to LED_MODE_OPER to + to set/unset the led unnaturally, set the "mode" to LED_MODE_OPER to blink the led, and LED_MODE_OFF to set the led off.*/ u8 bnx2x_set_led(struct bnx2x *bp, u8 port, u8 mode, u32 speed, u16 hw_led_mode, u32 chip_id); diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index d3c4c1ed07e..1bbcdb22d96 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -1151,8 +1151,8 @@ static inline void bnx2x_init_sge_ring_bit_mask(struct bnx2x_fastpath *fp) memset(fp->sge_mask, 0xff, (NUM_RX_SGE >> RX_SGE_MASK_ELEM_SHIFT)*sizeof(u64)); - /* Clear the two last indeces in the page to 1: - these are the indeces that correspond to the "next" element, + /* Clear the two last indices in the page to 1: + these are the indices that correspond to the "next" element, hence will never be indicated and should be removed from the calculations. */ bnx2x_clear_sge_mask_next_elems(fp); @@ -2011,7 +2011,7 @@ static u8 bnx2x_link_test(struct bnx2x *bp) sum of vn_min_rates or 0 - if all the min_rates are 0. - In the later case fainess algorithm should be deactivated. + In the later case fairness algorithm should be deactivated. If not all min_rates are zero then those that are zeroes will be set to 1. */ @@ -2134,7 +2134,7 @@ static void bnx2x_init_vn_minmax(struct bnx2x *bp, int func, FUNC_MF_CFG_MIN_BW_SHIFT) * 100; /* If FAIRNESS is enabled (not all min rates are zeroes) and if current min rate is zero - set it to 1. - This is a requirment of the algorithm. */ + This is a requirement of the algorithm. */ if ((vn_min_rate == 0) && wsum) vn_min_rate = DEF_MIN_RATE; vn_max_rate = ((vn_cfg & FUNC_MF_CFG_MAX_BW_MASK) >> @@ -6562,7 +6562,7 @@ static void bnx2x_reset_port(struct bnx2x *bp) val = REG_RD(bp, BRB1_REG_PORT_NUM_OCC_BLOCKS_0 + port*4); if (val) DP(NETIF_MSG_IFDOWN, - "BRB1 is not empty %d blooks are occupied\n", val); + "BRB1 is not empty %d blocks are occupied\n", val); /* TODO: Close Doorbell port? */ } @@ -6602,7 +6602,7 @@ static void bnx2x_reset_chip(struct bnx2x *bp, u32 reset_code) } } -/* msut be called with rtnl_lock */ +/* must be called with rtnl_lock */ static int bnx2x_nic_unload(struct bnx2x *bp, int unload_mode) { int port = BP_PORT(bp); @@ -7455,7 +7455,7 @@ static int __devinit bnx2x_get_hwinfo(struct bnx2x *bp) if (BP_NOMCP(bp)) { /* only supposed to happen on emulation/FPGA */ - BNX2X_ERR("warning rendom MAC workaround active\n"); + BNX2X_ERR("warning random MAC workaround active\n"); random_ether_addr(bp->dev->dev_addr); memcpy(bp->dev->perm_addr, bp->dev->dev_addr, ETH_ALEN); } @@ -8907,7 +8907,7 @@ static void bnx2x_self_test(struct net_device *dev, if (!netif_running(dev)) return; - /* offline tests are not suppoerted in MF mode */ + /* offline tests are not supported in MF mode */ if (IS_E1HMF(bp)) etest->flags &= ~ETH_TEST_FL_OFFLINE; @@ -9216,7 +9216,7 @@ static int bnx2x_set_power_state(struct bnx2x *bp, pci_power_t state) PCI_PM_CTRL_PME_STATUS)); if (pmcsr & PCI_PM_CTRL_STATE_MASK) - /* delay required during transition out of D3hot */ + /* delay required during transition out of D3hot */ msleep(20); break; @@ -9289,7 +9289,7 @@ poll_panic: /* we split the first BD into headers and data BDs - * to ease the pain of our fellow micocode engineers + * to ease the pain of our fellow microcode engineers * we use one mapping for both BDs * So far this has only been observed to happen * in Other Operating Systems(TM) @@ -9396,7 +9396,7 @@ static int bnx2x_pkt_req_lin(struct bnx2x *bp, struct sk_buff *skb, /* Check if LSO packet needs to be copied: 3 = 1 (for headers BD) + 2 (for PBD and last BD) */ int wnd_size = MAX_FETCH_BD - 3; - /* Number of widnows to check */ + /* Number of windows to check */ int num_wnds = skb_shinfo(skb)->nr_frags - wnd_size; int wnd_idx = 0; int frag_idx = 0; @@ -9498,7 +9498,7 @@ static int bnx2x_start_xmit(struct sk_buff *skb, struct net_device *dev) skb->ip_summed, skb->protocol, ipv6_hdr(skb)->nexthdr, ip_hdr(skb)->protocol, skb_shinfo(skb)->gso_type, xmit_type); - /* First, check if we need to linearaize the skb + /* First, check if we need to linearize the skb (due to FW restrictions) */ if (bnx2x_pkt_req_lin(bp, skb, xmit_type)) { /* Statistics of linearization */ diff --git a/drivers/net/bnx2x_reg.h b/drivers/net/bnx2x_reg.h index 5029d1e466f..a67b0c358ae 100644 --- a/drivers/net/bnx2x_reg.h +++ b/drivers/net/bnx2x_reg.h @@ -6,7 +6,7 @@ * it under the terms of the GNU General Public License as published by * the Free Software Foundation. * - * The registers description starts with the regsister Access type followed + * The registers description starts with the register Access type followed * by size in bits. For example [RW 32]. The access types are: * R - Read only * RC - Clear on read @@ -49,7 +49,7 @@ /* [RW 10] Write client 0: Assert pause threshold. */ #define BRB1_REG_PAUSE_LOW_THRESHOLD_0 0x60068 #define BRB1_REG_PAUSE_LOW_THRESHOLD_1 0x6006c -/* [R 24] The number of full blocks occpied by port. */ +/* [R 24] The number of full blocks occupied by port. */ #define BRB1_REG_PORT_NUM_OCC_BLOCKS_0 0x60094 /* [RW 1] Reset the design by software. */ #define BRB1_REG_SOFT_RESET 0x600dc @@ -1412,13 +1412,13 @@ #define MISC_REG_GPIO 0xa490 /* [R 28] this field hold the last information that caused reserved attention. bits [19:0] - address; [22:20] function; [23] reserved; - [27:24] the master thatcaused the attention - according to the following + [27:24] the master that caused the attention - according to the following encodeing:1 = pxp; 2 = mcp; 3 = usdm; 4 = tsdm; 5 = xsdm; 6 = csdm; 7 = dbu; 8 = dmae */ #define MISC_REG_GRC_RSV_ATTN 0xa3c0 /* [R 28] this field hold the last information that caused timeout attention. bits [19:0] - address; [22:20] function; [23] reserved; - [27:24] the master thatcaused the attention - according to the following + [27:24] the master that caused the attention - according to the following encodeing:1 = pxp; 2 = mcp; 3 = usdm; 4 = tsdm; 5 = xsdm; 6 = csdm; 7 = dbu; 8 = dmae */ #define MISC_REG_GRC_TIMEOUT_ATTN 0xa3c4 @@ -2320,7 +2320,7 @@ /* [RW 3] page size in L2P table for QM module; -4k; -8k; -16k; -32k; -64k; -128k */ #define PXP2_REG_RQ_QM_P_SIZE 0x120050 -/* [RW 1] 1' indicates that the RBC has finished configurating the PSWRQ */ +/* [RW 1] 1' indicates that the RBC has finished configuring the PSWRQ */ #define PXP2_REG_RQ_RBC_DONE 0x1201b0 /* [RW 3] Max burst size filed for read requests port 0; 000 - 128B; 001:256B; 010: 512B; 11:1K:100:2K; 01:4K */ @@ -2428,7 +2428,7 @@ /* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the buffer reaches this number has_payload will be asserted */ #define PXP2_REG_WR_DMAE_MPS 0x1205ec -/* [RW 10] if Number of entries in dmae fifo will be higer than this +/* [RW 10] if Number of entries in dmae fifo will be higher than this threshold then has_payload indication will be asserted; the default value should be equal to > write MBS size! */ #define PXP2_REG_WR_DMAE_TH 0x120368 @@ -2449,7 +2449,7 @@ /* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the buffer reaches this number has_payload will be asserted */ #define PXP2_REG_WR_TSDM_MPS 0x1205d4 -/* [RW 10] if Number of entries in usdmdp fifo will be higer than this +/* [RW 10] if Number of entries in usdmdp fifo will be higher than this threshold then has_payload indication will be asserted; the default value should be equal to > write MBS size! */ #define PXP2_REG_WR_USDMDP_TH 0x120348 @@ -3316,12 +3316,12 @@ #define XSEM_XSEM_INT_MASK_0_REG_ADDRESS_ERROR_SIZE 0 #define CFC_DEBUG1_REG_WRITE_AC (0x1<<4) #define CFC_DEBUG1_REG_WRITE_AC_SIZE 4 -/* [R 1] debug only: This bit indicates wheter indicates that external +/* [R 1] debug only: This bit indicates whether indicates that external buffer was wrapped (oldest data was thrown); Relevant only when ~dbg_registers_debug_target=2 (PCI) & ~dbg_registers_full_mode=1 (wrap); */ #define DBG_REG_WRAP_ON_EXT_BUFFER 0xc124 #define DBG_REG_WRAP_ON_EXT_BUFFER_SIZE 1 -/* [R 1] debug only: This bit indicates wheter the internal buffer was +/* [R 1] debug only: This bit indicates whether the internal buffer was wrapped (oldest data was thrown) Relevant only when ~dbg_registers_debug_target=0 (internal buffer) */ #define DBG_REG_WRAP_ON_INT_BUFFER 0xc128 -- GitLab From 6378c0253175e400525ac0efac9dd29f4e573cbf Mon Sep 17 00:00:00 2001 From: Eilon Greenstein Date: Wed, 13 Aug 2008 15:59:25 -0700 Subject: [PATCH 267/750] bnx2x: Checkpatch compliance Checkpatch compliance The latest version of checkpatch found the following style errors in the code Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x.h | 6 +- drivers/net/bnx2x_fw_defs.h | 154 ++++++++++++++++++------------------ drivers/net/bnx2x_init.h | 20 ++--- drivers/net/bnx2x_link.c | 8 +- drivers/net/bnx2x_main.c | 16 ++-- 5 files changed, 102 insertions(+), 102 deletions(-) diff --git a/drivers/net/bnx2x.h b/drivers/net/bnx2x.h index 33437e5bcec..b468f904c7f 100644 --- a/drivers/net/bnx2x.h +++ b/drivers/net/bnx2x.h @@ -40,20 +40,20 @@ #define DP(__mask, __fmt, __args...) do { \ if (bp->msglevel & (__mask)) \ printk(DP_LEVEL "[%s:%d(%s)]" __fmt, __func__, __LINE__, \ - bp->dev?(bp->dev->name):"?", ##__args); \ + bp->dev ? (bp->dev->name) : "?", ##__args); \ } while (0) /* errors debug print */ #define BNX2X_DBG_ERR(__fmt, __args...) do { \ if (bp->msglevel & NETIF_MSG_PROBE) \ printk(KERN_ERR "[%s:%d(%s)]" __fmt, __func__, __LINE__, \ - bp->dev?(bp->dev->name):"?", ##__args); \ + bp->dev ? (bp->dev->name) : "?", ##__args); \ } while (0) /* for errors (never masked) */ #define BNX2X_ERR(__fmt, __args...) do { \ printk(KERN_ERR "[%s:%d(%s)]" __fmt, __func__, __LINE__, \ - bp->dev?(bp->dev->name):"?", ##__args); \ + bp->dev ? (bp->dev->name) : "?", ##__args); \ } while (0) /* before we have a dev->name use dev_info() */ diff --git a/drivers/net/bnx2x_fw_defs.h b/drivers/net/bnx2x_fw_defs.h index 6e35761fc7d..192fa981b93 100644 --- a/drivers/net/bnx2x_fw_defs.h +++ b/drivers/net/bnx2x_fw_defs.h @@ -9,171 +9,171 @@ #define CSTORM_ASSERT_LIST_INDEX_OFFSET \ - (IS_E1H_OFFSET? 0x7000 : 0x1000) + (IS_E1H_OFFSET ? 0x7000 : 0x1000) #define CSTORM_ASSERT_LIST_OFFSET(idx) \ - (IS_E1H_OFFSET? (0x7020 + (idx * 0x10)) : (0x1020 + (idx * 0x10))) + (IS_E1H_OFFSET ? (0x7020 + (idx * 0x10)) : (0x1020 + (idx * 0x10))) #define CSTORM_DEF_SB_HC_DISABLE_OFFSET(function, index) \ - (IS_E1H_OFFSET? (0x8522 + ((function>>1) * 0x40) + ((function&1) \ - * 0x100) + (index * 0x4)) : (0x1922 + (function * 0x40) + (index \ - * 0x4))) + (IS_E1H_OFFSET ? (0x8522 + ((function>>1) * 0x40) + \ + ((function&1) * 0x100) + (index * 0x4)) : (0x1922 + (function * \ + 0x40) + (index * 0x4))) #define CSTORM_DEF_SB_HOST_SB_ADDR_OFFSET(function) \ - (IS_E1H_OFFSET? (0x8500 + ((function>>1) * 0x40) + ((function&1) \ - * 0x100)) : (0x1900 + (function * 0x40))) + (IS_E1H_OFFSET ? (0x8500 + ((function>>1) * 0x40) + \ + ((function&1) * 0x100)) : (0x1900 + (function * 0x40))) #define CSTORM_DEF_SB_HOST_STATUS_BLOCK_OFFSET(function) \ - (IS_E1H_OFFSET? (0x8508 + ((function>>1) * 0x40) + ((function&1) \ - * 0x100)) : (0x1908 + (function * 0x40))) + (IS_E1H_OFFSET ? (0x8508 + ((function>>1) * 0x40) + \ + ((function&1) * 0x100)) : (0x1908 + (function * 0x40))) #define CSTORM_FUNCTION_MODE_OFFSET \ - (IS_E1H_OFFSET? 0x11e8 : 0xffffffff) + (IS_E1H_OFFSET ? 0x11e8 : 0xffffffff) #define CSTORM_HC_BTR_OFFSET(port) \ - (IS_E1H_OFFSET? (0x8704 + (port * 0xf0)) : (0x1984 + (port * 0xc0))) + (IS_E1H_OFFSET ? (0x8704 + (port * 0xf0)) : (0x1984 + (port * 0xc0))) #define CSTORM_SB_HC_DISABLE_OFFSET(port, cpu_id, index) \ - (IS_E1H_OFFSET? (0x801a + (port * 0x280) + (cpu_id * 0x28) + \ + (IS_E1H_OFFSET ? (0x801a + (port * 0x280) + (cpu_id * 0x28) + \ (index * 0x4)) : (0x141a + (port * 0x280) + (cpu_id * 0x28) + \ (index * 0x4))) #define CSTORM_SB_HC_TIMEOUT_OFFSET(port, cpu_id, index) \ - (IS_E1H_OFFSET? (0x8018 + (port * 0x280) + (cpu_id * 0x28) + \ + (IS_E1H_OFFSET ? (0x8018 + (port * 0x280) + (cpu_id * 0x28) + \ (index * 0x4)) : (0x1418 + (port * 0x280) + (cpu_id * 0x28) + \ (index * 0x4))) #define CSTORM_SB_HOST_SB_ADDR_OFFSET(port, cpu_id) \ - (IS_E1H_OFFSET? (0x8000 + (port * 0x280) + (cpu_id * 0x28)) : \ + (IS_E1H_OFFSET ? (0x8000 + (port * 0x280) + (cpu_id * 0x28)) : \ (0x1400 + (port * 0x280) + (cpu_id * 0x28))) #define CSTORM_SB_HOST_STATUS_BLOCK_OFFSET(port, cpu_id) \ - (IS_E1H_OFFSET? (0x8008 + (port * 0x280) + (cpu_id * 0x28)) : \ + (IS_E1H_OFFSET ? (0x8008 + (port * 0x280) + (cpu_id * 0x28)) : \ (0x1408 + (port * 0x280) + (cpu_id * 0x28))) #define CSTORM_STATS_FLAGS_OFFSET(function) \ - (IS_E1H_OFFSET? (0x1108 + (function * 0x8)) : (0x5108 + \ + (IS_E1H_OFFSET ? (0x1108 + (function * 0x8)) : (0x5108 + \ (function * 0x8))) #define TSTORM_APPROXIMATE_MATCH_MULTICAST_FILTERING_OFFSET(function) \ - (IS_E1H_OFFSET? (0x31c0 + (function * 0x20)) : 0xffffffff) + (IS_E1H_OFFSET ? (0x31c0 + (function * 0x20)) : 0xffffffff) #define TSTORM_ASSERT_LIST_INDEX_OFFSET \ - (IS_E1H_OFFSET? 0xa000 : 0x1000) + (IS_E1H_OFFSET ? 0xa000 : 0x1000) #define TSTORM_ASSERT_LIST_OFFSET(idx) \ - (IS_E1H_OFFSET? (0xa020 + (idx * 0x10)) : (0x1020 + (idx * 0x10))) + (IS_E1H_OFFSET ? (0xa020 + (idx * 0x10)) : (0x1020 + (idx * 0x10))) #define TSTORM_CLIENT_CONFIG_OFFSET(port, client_id) \ - (IS_E1H_OFFSET? (0x3358 + (port * 0x3e8) + (client_id * 0x28)) : \ - (0x9c8 + (port * 0x2f8) + (client_id * 0x28))) + (IS_E1H_OFFSET ? (0x3358 + (port * 0x3e8) + (client_id * 0x28)) \ + : (0x9c8 + (port * 0x2f8) + (client_id * 0x28))) #define TSTORM_DEF_SB_HC_DISABLE_OFFSET(function, index) \ - (IS_E1H_OFFSET? (0xb01a + ((function>>1) * 0x28) + ((function&1) \ - * 0xa0) + (index * 0x4)) : (0x141a + (function * 0x28) + (index * \ - 0x4))) + (IS_E1H_OFFSET ? (0xb01a + ((function>>1) * 0x28) + \ + ((function&1) * 0xa0) + (index * 0x4)) : (0x141a + (function * \ + 0x28) + (index * 0x4))) #define TSTORM_DEF_SB_HOST_SB_ADDR_OFFSET(function) \ - (IS_E1H_OFFSET? (0xb000 + ((function>>1) * 0x28) + ((function&1) \ - * 0xa0)) : (0x1400 + (function * 0x28))) + (IS_E1H_OFFSET ? (0xb000 + ((function>>1) * 0x28) + \ + ((function&1) * 0xa0)) : (0x1400 + (function * 0x28))) #define TSTORM_DEF_SB_HOST_STATUS_BLOCK_OFFSET(function) \ - (IS_E1H_OFFSET? (0xb008 + ((function>>1) * 0x28) + ((function&1) \ - * 0xa0)) : (0x1408 + (function * 0x28))) + (IS_E1H_OFFSET ? (0xb008 + ((function>>1) * 0x28) + \ + ((function&1) * 0xa0)) : (0x1408 + (function * 0x28))) #define TSTORM_ETH_STATS_QUERY_ADDR_OFFSET(function) \ - (IS_E1H_OFFSET? (0x2b80 + (function * 0x8)) : (0x4b68 + \ + (IS_E1H_OFFSET ? (0x2b80 + (function * 0x8)) : (0x4b68 + \ (function * 0x8))) #define TSTORM_FUNCTION_COMMON_CONFIG_OFFSET(function) \ - (IS_E1H_OFFSET? (0x3000 + (function * 0x38)) : (0x1500 + \ + (IS_E1H_OFFSET ? (0x3000 + (function * 0x38)) : (0x1500 + \ (function * 0x38))) #define TSTORM_FUNCTION_MODE_OFFSET \ - (IS_E1H_OFFSET? 0x1ad0 : 0xffffffff) + (IS_E1H_OFFSET ? 0x1ad0 : 0xffffffff) #define TSTORM_HC_BTR_OFFSET(port) \ - (IS_E1H_OFFSET? (0xb144 + (port * 0x30)) : (0x1454 + (port * 0x18))) + (IS_E1H_OFFSET ? (0xb144 + (port * 0x30)) : (0x1454 + (port * 0x18))) #define TSTORM_INDIRECTION_TABLE_OFFSET(function) \ - (IS_E1H_OFFSET? (0x12c8 + (function * 0x80)) : (0x22c8 + \ + (IS_E1H_OFFSET ? (0x12c8 + (function * 0x80)) : (0x22c8 + \ (function * 0x80))) #define TSTORM_INDIRECTION_TABLE_SIZE 0x80 #define TSTORM_MAC_FILTER_CONFIG_OFFSET(function) \ - (IS_E1H_OFFSET? (0x3008 + (function * 0x38)) : (0x1508 + \ + (IS_E1H_OFFSET ? (0x3008 + (function * 0x38)) : (0x1508 + \ (function * 0x38))) #define TSTORM_PER_COUNTER_ID_STATS_OFFSET(port, stats_counter_id) \ (IS_E1H_OFFSET ? (0x2010 + (port * 0x5b0) + (stats_counter_id * \ 0x50)) : (0x4000 + (port * 0x3f0) + (stats_counter_id * 0x38))) #define TSTORM_RX_PRODS_OFFSET(port, client_id) \ - (IS_E1H_OFFSET? (0x3350 + (port * 0x3e8) + (client_id * 0x28)) : \ - (0x9c0 + (port * 0x2f8) + (client_id * 0x28))) + (IS_E1H_OFFSET ? (0x3350 + (port * 0x3e8) + (client_id * 0x28)) \ + : (0x9c0 + (port * 0x2f8) + (client_id * 0x28))) #define TSTORM_STATS_FLAGS_OFFSET(function) \ - (IS_E1H_OFFSET? (0x2c00 + (function * 0x8)) : (0x4b88 + \ + (IS_E1H_OFFSET ? (0x2c00 + (function * 0x8)) : (0x4b88 + \ (function * 0x8))) -#define TSTORM_TPA_EXIST_OFFSET (IS_E1H_OFFSET? 0x3b30 : 0x1c20) -#define USTORM_AGG_DATA_OFFSET (IS_E1H_OFFSET? 0xa040 : 0x2c10) -#define USTORM_AGG_DATA_SIZE (IS_E1H_OFFSET? 0x2440 : 0x1200) +#define TSTORM_TPA_EXIST_OFFSET (IS_E1H_OFFSET ? 0x3b30 : 0x1c20) +#define USTORM_AGG_DATA_OFFSET (IS_E1H_OFFSET ? 0xa040 : 0x2c10) +#define USTORM_AGG_DATA_SIZE (IS_E1H_OFFSET ? 0x2440 : 0x1200) #define USTORM_ASSERT_LIST_INDEX_OFFSET \ - (IS_E1H_OFFSET? 0x8000 : 0x1000) + (IS_E1H_OFFSET ? 0x8000 : 0x1000) #define USTORM_ASSERT_LIST_OFFSET(idx) \ - (IS_E1H_OFFSET? (0x8020 + (idx * 0x10)) : (0x1020 + (idx * 0x10))) + (IS_E1H_OFFSET ? (0x8020 + (idx * 0x10)) : (0x1020 + (idx * 0x10))) #define USTORM_CQE_PAGE_BASE_OFFSET(port, clientId) \ - (IS_E1H_OFFSET? (0x3298 + (port * 0x258) + (clientId * 0x18)) : \ + (IS_E1H_OFFSET ? (0x3298 + (port * 0x258) + (clientId * 0x18)) : \ (0x5450 + (port * 0x1c8) + (clientId * 0x18))) #define USTORM_DEF_SB_HC_DISABLE_OFFSET(function, index) \ - (IS_E1H_OFFSET? (0x951a + ((function>>1) * 0x28) + ((function&1) \ - * 0xa0) + (index * 0x4)) : (0x191a + (function * 0x28) + (index * \ - 0x4))) + (IS_E1H_OFFSET ? (0x951a + ((function>>1) * 0x28) + \ + ((function&1) * 0xa0) + (index * 0x4)) : (0x191a + (function * \ + 0x28) + (index * 0x4))) #define USTORM_DEF_SB_HOST_SB_ADDR_OFFSET(function) \ - (IS_E1H_OFFSET? (0x9500 + ((function>>1) * 0x28) + ((function&1) \ - * 0xa0)) : (0x1900 + (function * 0x28))) + (IS_E1H_OFFSET ? (0x9500 + ((function>>1) * 0x28) + \ + ((function&1) * 0xa0)) : (0x1900 + (function * 0x28))) #define USTORM_DEF_SB_HOST_STATUS_BLOCK_OFFSET(function) \ - (IS_E1H_OFFSET? (0x9508 + ((function>>1) * 0x28) + ((function&1) \ - * 0xa0)) : (0x1908 + (function * 0x28))) + (IS_E1H_OFFSET ? (0x9508 + ((function>>1) * 0x28) + \ + ((function&1) * 0xa0)) : (0x1908 + (function * 0x28))) #define USTORM_FUNCTION_MODE_OFFSET \ - (IS_E1H_OFFSET? 0x2448 : 0xffffffff) + (IS_E1H_OFFSET ? 0x2448 : 0xffffffff) #define USTORM_HC_BTR_OFFSET(port) \ - (IS_E1H_OFFSET? (0x9644 + (port * 0xd0)) : (0x1954 + (port * 0xb8))) + (IS_E1H_OFFSET ? (0x9644 + (port * 0xd0)) : (0x1954 + (port * 0xb8))) #define USTORM_MAX_AGG_SIZE_OFFSET(port, clientId) \ - (IS_E1H_OFFSET? (0x3290 + (port * 0x258) + (clientId * 0x18)) : \ + (IS_E1H_OFFSET ? (0x3290 + (port * 0x258) + (clientId * 0x18)) : \ (0x5448 + (port * 0x1c8) + (clientId * 0x18))) #define USTORM_MEM_WORKAROUND_ADDRESS_OFFSET(function) \ - (IS_E1H_OFFSET? (0x2408 + (function * 0x8)) : (0x5408 + \ + (IS_E1H_OFFSET ? (0x2408 + (function * 0x8)) : (0x5408 + \ (function * 0x8))) #define USTORM_SB_HC_DISABLE_OFFSET(port, cpu_id, index) \ - (IS_E1H_OFFSET? (0x901a + (port * 0x280) + (cpu_id * 0x28) + \ + (IS_E1H_OFFSET ? (0x901a + (port * 0x280) + (cpu_id * 0x28) + \ (index * 0x4)) : (0x141a + (port * 0x280) + (cpu_id * 0x28) + \ (index * 0x4))) #define USTORM_SB_HC_TIMEOUT_OFFSET(port, cpu_id, index) \ - (IS_E1H_OFFSET? (0x9018 + (port * 0x280) + (cpu_id * 0x28) + \ + (IS_E1H_OFFSET ? (0x9018 + (port * 0x280) + (cpu_id * 0x28) + \ (index * 0x4)) : (0x1418 + (port * 0x280) + (cpu_id * 0x28) + \ (index * 0x4))) #define USTORM_SB_HOST_SB_ADDR_OFFSET(port, cpu_id) \ - (IS_E1H_OFFSET? (0x9000 + (port * 0x280) + (cpu_id * 0x28)) : \ + (IS_E1H_OFFSET ? (0x9000 + (port * 0x280) + (cpu_id * 0x28)) : \ (0x1400 + (port * 0x280) + (cpu_id * 0x28))) #define USTORM_SB_HOST_STATUS_BLOCK_OFFSET(port, cpu_id) \ - (IS_E1H_OFFSET? (0x9008 + (port * 0x280) + (cpu_id * 0x28)) : \ + (IS_E1H_OFFSET ? (0x9008 + (port * 0x280) + (cpu_id * 0x28)) : \ (0x1408 + (port * 0x280) + (cpu_id * 0x28))) #define XSTORM_ASSERT_LIST_INDEX_OFFSET \ - (IS_E1H_OFFSET? 0x9000 : 0x1000) + (IS_E1H_OFFSET ? 0x9000 : 0x1000) #define XSTORM_ASSERT_LIST_OFFSET(idx) \ - (IS_E1H_OFFSET? (0x9020 + (idx * 0x10)) : (0x1020 + (idx * 0x10))) + (IS_E1H_OFFSET ? (0x9020 + (idx * 0x10)) : (0x1020 + (idx * 0x10))) #define XSTORM_CMNG_PER_PORT_VARS_OFFSET(port) \ - (IS_E1H_OFFSET? (0x24a8 + (port * 0x40)) : (0x3ba0 + (port * 0x40))) + (IS_E1H_OFFSET ? (0x24a8 + (port * 0x40)) : (0x3ba0 + (port * 0x40))) #define XSTORM_DEF_SB_HC_DISABLE_OFFSET(function, index) \ - (IS_E1H_OFFSET? (0xa01a + ((function>>1) * 0x28) + ((function&1) \ - * 0xa0) + (index * 0x4)) : (0x141a + (function * 0x28) + (index * \ - 0x4))) + (IS_E1H_OFFSET ? (0xa01a + ((function>>1) * 0x28) + \ + ((function&1) * 0xa0) + (index * 0x4)) : (0x141a + (function * \ + 0x28) + (index * 0x4))) #define XSTORM_DEF_SB_HOST_SB_ADDR_OFFSET(function) \ - (IS_E1H_OFFSET? (0xa000 + ((function>>1) * 0x28) + ((function&1) \ - * 0xa0)) : (0x1400 + (function * 0x28))) + (IS_E1H_OFFSET ? (0xa000 + ((function>>1) * 0x28) + \ + ((function&1) * 0xa0)) : (0x1400 + (function * 0x28))) #define XSTORM_DEF_SB_HOST_STATUS_BLOCK_OFFSET(function) \ - (IS_E1H_OFFSET? (0xa008 + ((function>>1) * 0x28) + ((function&1) \ - * 0xa0)) : (0x1408 + (function * 0x28))) + (IS_E1H_OFFSET ? (0xa008 + ((function>>1) * 0x28) + \ + ((function&1) * 0xa0)) : (0x1408 + (function * 0x28))) #define XSTORM_E1HOV_OFFSET(function) \ - (IS_E1H_OFFSET? (0x2ab8 + (function * 0x2)) : 0xffffffff) + (IS_E1H_OFFSET ? (0x2ab8 + (function * 0x2)) : 0xffffffff) #define XSTORM_ETH_STATS_QUERY_ADDR_OFFSET(function) \ - (IS_E1H_OFFSET? (0x2418 + (function * 0x8)) : (0x3b70 + \ + (IS_E1H_OFFSET ? (0x2418 + (function * 0x8)) : (0x3b70 + \ (function * 0x8))) #define XSTORM_FAIRNESS_PER_VN_VARS_OFFSET(function) \ - (IS_E1H_OFFSET? (0x2568 + (function * 0x70)) : (0x3c60 + \ + (IS_E1H_OFFSET ? (0x2568 + (function * 0x70)) : (0x3c60 + \ (function * 0x70))) #define XSTORM_FUNCTION_MODE_OFFSET \ - (IS_E1H_OFFSET? 0x2ac8 : 0xffffffff) + (IS_E1H_OFFSET ? 0x2ac8 : 0xffffffff) #define XSTORM_HC_BTR_OFFSET(port) \ - (IS_E1H_OFFSET? (0xa144 + (port * 0x30)) : (0x1454 + (port * 0x18))) + (IS_E1H_OFFSET ? (0xa144 + (port * 0x30)) : (0x1454 + (port * 0x18))) #define XSTORM_PER_COUNTER_ID_STATS_OFFSET(port, stats_counter_id) \ (IS_E1H_OFFSET ? (0xc000 + (port * 0x3f0) + (stats_counter_id * \ 0x38)) : (0x3378 + (port * 0x3f0) + (stats_counter_id * 0x38))) #define XSTORM_RATE_SHAPING_PER_VN_VARS_OFFSET(function) \ - (IS_E1H_OFFSET? (0x2528 + (function * 0x70)) : (0x3c20 + \ + (IS_E1H_OFFSET ? (0x2528 + (function * 0x70)) : (0x3c20 + \ (function * 0x70))) #define XSTORM_SPQ_PAGE_BASE_OFFSET(function) \ - (IS_E1H_OFFSET? (0x2000 + (function * 0x10)) : (0x3328 + \ + (IS_E1H_OFFSET ? (0x2000 + (function * 0x10)) : (0x3328 + \ (function * 0x10))) #define XSTORM_SPQ_PROD_OFFSET(function) \ - (IS_E1H_OFFSET? (0x2008 + (function * 0x10)) : (0x3330 + \ + (IS_E1H_OFFSET ? (0x2008 + (function * 0x10)) : (0x3330 + \ (function * 0x10))) #define XSTORM_STATS_FLAGS_OFFSET(function) \ - (IS_E1H_OFFSET? (0x23d8 + (function * 0x8)) : (0x3b60 + \ + (IS_E1H_OFFSET ? (0x23d8 + (function * 0x8)) : (0x3b60 + \ (function * 0x8))) #define COMMON_ASM_INVALID_ASSERT_OPCODE 0x0 diff --git a/drivers/net/bnx2x_init.h b/drivers/net/bnx2x_init.h index f62891bf757..130927cfc75 100644 --- a/drivers/net/bnx2x_init.h +++ b/drivers/net/bnx2x_init.h @@ -72,26 +72,26 @@ struct raw_op { - u32 op :8; - u32 offset :24; + u32 op:8; + u32 offset:24; u32 raw_data; }; struct op_read { - u32 op :8; - u32 offset :24; + u32 op:8; + u32 offset:24; u32 pad; }; struct op_write { - u32 op :8; - u32 offset :24; + u32 op:8; + u32 offset:24; u32 val; }; struct op_string_write { - u32 op :8; - u32 offset :24; + u32 op:8; + u32 offset:24; #ifdef __LITTLE_ENDIAN u16 data_off; u16 data_len; @@ -102,8 +102,8 @@ struct op_string_write { }; struct op_zero { - u32 op :8; - u32 offset :24; + u32 op:8; + u32 offset:24; u32 len; }; diff --git a/drivers/net/bnx2x_link.c b/drivers/net/bnx2x_link.c index d7398a34f93..8b92c6ad075 100644 --- a/drivers/net/bnx2x_link.c +++ b/drivers/net/bnx2x_link.c @@ -755,10 +755,10 @@ static u32 bnx2x_get_emac_base(u32 ext_phy_type, u8 port) emac_base = GRCBASE_EMAC0; break; case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: - emac_base = (port) ? GRCBASE_EMAC0: GRCBASE_EMAC1; + emac_base = (port) ? GRCBASE_EMAC0 : GRCBASE_EMAC1; break; default: - emac_base = (port) ? GRCBASE_EMAC1: GRCBASE_EMAC0; + emac_base = (port) ? GRCBASE_EMAC1 : GRCBASE_EMAC0; break; } return emac_base; @@ -3549,7 +3549,7 @@ static void bnx2x_set_xgxs_loopback(struct link_params *params, struct bnx2x *bp = params->bp; if (is_10g) { - u32 md_devad; + u32 md_devad; DP(NETIF_MSG_LINK, "XGXS 10G loopback enable\n"); @@ -4505,7 +4505,7 @@ static void bnx2x_sfx7101_sp_sw_reset(struct bnx2x *bp, u8 port, u8 phy_addr) } #define RESERVED_SIZE 256 /* max application is 160K bytes - data at end of RAM */ -#define MAX_APP_SIZE 160*1024 - RESERVED_SIZE +#define MAX_APP_SIZE (160*1024 - RESERVED_SIZE) /* Header is 14 bytes */ #define HEADER_SIZE 14 diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index 1bbcdb22d96..f285f0bbaa1 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -1858,14 +1858,14 @@ static int bnx2x_set_spio(struct bnx2x *bp, int spio_num, u32 mode) spio_reg = (REG_RD(bp, MISC_REG_SPIO) & MISC_REGISTERS_SPIO_FLOAT); switch (mode) { - case MISC_REGISTERS_SPIO_OUTPUT_LOW : + case MISC_REGISTERS_SPIO_OUTPUT_LOW: DP(NETIF_MSG_LINK, "Set SPIO %d -> output low\n", spio_num); /* clear FLOAT and set CLR */ spio_reg &= ~(spio_mask << MISC_REGISTERS_SPIO_FLOAT_POS); spio_reg |= (spio_mask << MISC_REGISTERS_SPIO_CLR_POS); break; - case MISC_REGISTERS_SPIO_OUTPUT_HIGH : + case MISC_REGISTERS_SPIO_OUTPUT_HIGH: DP(NETIF_MSG_LINK, "Set SPIO %d -> output high\n", spio_num); /* clear FLOAT and set SET */ spio_reg &= ~(spio_mask << MISC_REGISTERS_SPIO_FLOAT_POS); @@ -2759,7 +2759,7 @@ static void bnx2x_attn_int_deasserted(struct bnx2x *bp, u32 deasserted) HW_PRTY_ASSERT_SET_1) || (attn.sig[2] & group_mask.sig[2] & HW_PRTY_ASSERT_SET_2)) - BNX2X_ERR("FATAL HW block parity attention\n"); + BNX2X_ERR("FATAL HW block parity attention\n"); } } @@ -2904,11 +2904,11 @@ static irqreturn_t bnx2x_msix_sp_int(int irq, void *dev_instance) /* underflow */ \ d_hi = m_hi - s_hi; \ if (d_hi > 0) { \ - /* we can 'loan' 1 */ \ + /* we can 'loan' 1 */ \ d_hi--; \ d_lo = m_lo + (UINT_MAX - s_lo) + 1; \ } else { \ - /* m_hi <= s_hi */ \ + /* m_hi <= s_hi */ \ d_hi = 0; \ d_lo = 0; \ } \ @@ -2918,7 +2918,7 @@ static irqreturn_t bnx2x_msix_sp_int(int irq, void *dev_instance) d_hi = 0; \ d_lo = 0; \ } else { \ - /* m_hi >= s_hi */ \ + /* m_hi >= s_hi */ \ d_hi = m_hi - s_hi; \ d_lo = m_lo - s_lo; \ } \ @@ -3782,7 +3782,7 @@ static void bnx2x_stats_update(struct bnx2x *bp) bp->fp->rx_comp_cons), le16_to_cpu(*bp->fp->rx_cons_sb), nstats->rx_packets); printk(KERN_DEBUG " %s (Xoff events %u) brb drops %u\n", - netif_queue_stopped(bp->dev)? "Xoff" : "Xon", + netif_queue_stopped(bp->dev) ? "Xoff" : "Xon", estats->driver_xoff, estats->brb_drop_lo); printk(KERN_DEBUG "tstats: checksum_discard %u " "packets_too_big_discard %u no_buff_discard %u " @@ -9610,7 +9610,7 @@ static int bnx2x_start_xmit(struct sk_buff *skb, struct net_device *dev) tx_bd->addr_hi = cpu_to_le32(U64_HI(mapping)); tx_bd->addr_lo = cpu_to_le32(U64_LO(mapping)); - nbd = skb_shinfo(skb)->nr_frags + ((pbd == NULL)? 1 : 2); + nbd = skb_shinfo(skb)->nr_frags + ((pbd == NULL) ? 1 : 2); tx_bd->nbd = cpu_to_le16(nbd); tx_bd->nbytes = cpu_to_le16(skb_headlen(skb)); -- GitLab From 1bb5bd2c713cdf19794996fafd7b48da4c4b0113 Mon Sep 17 00:00:00 2001 From: Eilon Greenstein Date: Wed, 13 Aug 2008 15:59:45 -0700 Subject: [PATCH 268/750] bnx2x: Version update Version update Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/bnx2x_main.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index f285f0bbaa1..3e7dc171cdf 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -60,8 +60,8 @@ #include "bnx2x.h" #include "bnx2x_init.h" -#define DRV_MODULE_VERSION "1.45.6" -#define DRV_MODULE_RELDATE "2008/06/23" +#define DRV_MODULE_VERSION "1.45.17" +#define DRV_MODULE_RELDATE "2008/08/13" #define BNX2X_BC_VER 0x040200 /* Time in jiffies before concluding the transmitter is hung */ -- GitLab From 877acedc0d3ea07f7b36573ed2f1f479c2c1eefd Mon Sep 17 00:00:00 2001 From: Daniel Lezcano Date: Wed, 13 Aug 2008 16:15:57 -0700 Subject: [PATCH 269/750] netns: Fix crash by making igmp per namespace This patch makes the multicast socket to be per namespace. When a network namespace is created, other than the init_net and a multicast packet is received, the kernel goes to a hang or a kernel panic. How to reproduce ? * create a child network namespace * create a pair virtual device veth * ip link add type veth * move one side to the pair network device to the child namespace * ip link set netns dev veth1 * ping -I veth0 224.0.0.1 The bug appears because the function ip_mc_init_dev does not initialize the different multicast fields as it exits because it is not the init_net. BUG: soft lockup - CPU#0 stuck for 61s! [avahi-daemon:2695] Modules linked in: irq event stamp: 50350 hardirqs last enabled at (50349): [] _spin_unlock_irqrestore+0x34/0x39 hardirqs last disabled at (50350): [] schedule+0x9f/0x5ff softirqs last enabled at (45712): [] ip_setsockopt+0x8e7/0x909 softirqs last disabled at (45710): [] _spin_lock_bh+0x8/0x27 Pid: 2695, comm: avahi-daemon Not tainted (2.6.27-rc2-00029-g0872073 #3) EIP: 0060:[] EFLAGS: 00000297 CPU: 0 EIP is at __read_lock_failed+0x8/0x10 EAX: c4f38810 EBX: c4f38810 ECX: 00000000 EDX: c04cc22e ESI: fb0000e0 EDI: 00000011 EBP: 0f02000a ESP: c4e3faa0 DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 CR0: 8005003b CR2: 44618a40 CR3: 04e37000 CR4: 000006d0 DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000 DR6: ffff0ff0 DR7: 00000400 [] ? _raw_read_lock+0x23/0x25 [] ? ip_check_mc+0x1c/0x83 [] ? ip_route_input+0x229/0xe92 [] ? trace_hardirqs_on_thunk+0xc/0x10 [] ? do_IRQ+0x69/0x7d [] ? restore_nocheck_notrace+0x0/0xe [] ? ip_rcv+0x227/0x505 [] ? netif_receive_skb+0xfe/0x2b3 [] ? netif_receive_skb+0x26c/0x2b3 [] ? process_backlog+0x73/0xbd [] ? net_rx_action+0xc1/0x1ae [] ? __do_softirq+0x7b/0xef [] ? do_softirq+0x37/0x4d [] ? dev_queue_xmit+0x3d4/0x40b [] ? local_bh_enable+0x96/0xab [] ? dev_queue_xmit+0x3d4/0x40b [] ? _local_bh_enable+0x79/0x88 [] ? neigh_resolve_output+0x20f/0x239 [] ? ip_finish_output+0x1df/0x209 [] ? ip_dev_loopback_xmit+0x62/0x66 [] ? ip_local_out+0x15/0x17 [] ? ip_push_pending_frames+0x25c/0x2bb [] ? udp_push_pending_frames+0x2bb/0x30e [] ? udp_sendmsg+0x413/0x51d [] ? udp_sendmsg+0x433/0x51d [] ? inet_sendmsg+0x35/0x3f [] ? sock_sendmsg+0xb8/0xd1 [] ? autoremove_wake_function+0x0/0x2b [] ? copy_from_user+0x32/0x5e [] ? copy_from_user+0x32/0x5e [] ? sys_sendmsg+0x18d/0x1f0 [] ? pipe_write+0x3cb/0x3d7 [] ? do_sync_write+0xbe/0x105 [] ? autoremove_wake_function+0x0/0x2b [] ? sys_socketcall+0x176/0x1b0 [] ? syscall_trace_enter+0x6c/0x7b [] ? syscall_call+0x7/0xb Signed-off-by: Daniel Lezcano Signed-off-by: David S. Miller --- net/ipv4/igmp.c | 71 ++++++++++++++----------------------------------- 1 file changed, 20 insertions(+), 51 deletions(-) diff --git a/net/ipv4/igmp.c b/net/ipv4/igmp.c index 6203ece5360..f70fac61259 100644 --- a/net/ipv4/igmp.c +++ b/net/ipv4/igmp.c @@ -289,6 +289,7 @@ static struct sk_buff *igmpv3_newpack(struct net_device *dev, int size) struct rtable *rt; struct iphdr *pip; struct igmpv3_report *pig; + struct net *net = dev_net(dev); skb = alloc_skb(size + LL_ALLOCATED_SPACE(dev), GFP_ATOMIC); if (skb == NULL) @@ -299,7 +300,7 @@ static struct sk_buff *igmpv3_newpack(struct net_device *dev, int size) .nl_u = { .ip4_u = { .daddr = IGMPV3_ALL_MCR } }, .proto = IPPROTO_IGMP }; - if (ip_route_output_key(&init_net, &rt, &fl)) { + if (ip_route_output_key(net, &rt, &fl)) { kfree_skb(skb); return NULL; } @@ -629,6 +630,7 @@ static int igmp_send_report(struct in_device *in_dev, struct ip_mc_list *pmc, struct igmphdr *ih; struct rtable *rt; struct net_device *dev = in_dev->dev; + struct net *net = dev_net(dev); __be32 group = pmc ? pmc->multiaddr : 0; __be32 dst; @@ -643,7 +645,7 @@ static int igmp_send_report(struct in_device *in_dev, struct ip_mc_list *pmc, struct flowi fl = { .oif = dev->ifindex, .nl_u = { .ip4_u = { .daddr = dst } }, .proto = IPPROTO_IGMP }; - if (ip_route_output_key(&init_net, &rt, &fl)) + if (ip_route_output_key(net, &rt, &fl)) return -1; } if (rt->rt_src == 0) { @@ -1196,9 +1198,6 @@ void ip_mc_inc_group(struct in_device *in_dev, __be32 addr) ASSERT_RTNL(); - if (!net_eq(dev_net(in_dev->dev), &init_net)) - return; - for (im=in_dev->mc_list; im; im=im->next) { if (im->multiaddr == addr) { im->users++; @@ -1278,9 +1277,6 @@ void ip_mc_dec_group(struct in_device *in_dev, __be32 addr) ASSERT_RTNL(); - if (!net_eq(dev_net(in_dev->dev), &init_net)) - return; - for (ip=&in_dev->mc_list; (i=*ip)!=NULL; ip=&i->next) { if (i->multiaddr==addr) { if (--i->users == 0) { @@ -1308,9 +1304,6 @@ void ip_mc_down(struct in_device *in_dev) ASSERT_RTNL(); - if (!net_eq(dev_net(in_dev->dev), &init_net)) - return; - for (i=in_dev->mc_list; i; i=i->next) igmp_group_dropped(i); @@ -1331,9 +1324,6 @@ void ip_mc_init_dev(struct in_device *in_dev) { ASSERT_RTNL(); - if (!net_eq(dev_net(in_dev->dev), &init_net)) - return; - in_dev->mc_tomb = NULL; #ifdef CONFIG_IP_MULTICAST in_dev->mr_gq_running = 0; @@ -1357,9 +1347,6 @@ void ip_mc_up(struct in_device *in_dev) ASSERT_RTNL(); - if (!net_eq(dev_net(in_dev->dev), &init_net)) - return; - ip_mc_inc_group(in_dev, IGMP_ALL_HOSTS); for (i=in_dev->mc_list; i; i=i->next) @@ -1376,9 +1363,6 @@ void ip_mc_destroy_dev(struct in_device *in_dev) ASSERT_RTNL(); - if (!net_eq(dev_net(in_dev->dev), &init_net)) - return; - /* Deactivate timers */ ip_mc_down(in_dev); @@ -1395,7 +1379,7 @@ void ip_mc_destroy_dev(struct in_device *in_dev) write_unlock_bh(&in_dev->mc_list_lock); } -static struct in_device * ip_mc_find_dev(struct ip_mreqn *imr) +static struct in_device *ip_mc_find_dev(struct net *net, struct ip_mreqn *imr) { struct flowi fl = { .nl_u = { .ip4_u = { .daddr = imr->imr_multiaddr.s_addr } } }; @@ -1404,19 +1388,19 @@ static struct in_device * ip_mc_find_dev(struct ip_mreqn *imr) struct in_device *idev = NULL; if (imr->imr_ifindex) { - idev = inetdev_by_index(&init_net, imr->imr_ifindex); + idev = inetdev_by_index(net, imr->imr_ifindex); if (idev) __in_dev_put(idev); return idev; } if (imr->imr_address.s_addr) { - dev = ip_dev_find(&init_net, imr->imr_address.s_addr); + dev = ip_dev_find(net, imr->imr_address.s_addr); if (!dev) return NULL; dev_put(dev); } - if (!dev && !ip_route_output_key(&init_net, &rt, &fl)) { + if (!dev && !ip_route_output_key(net, &rt, &fl)) { dev = rt->u.dst.dev; ip_rt_put(rt); } @@ -1754,18 +1738,16 @@ int ip_mc_join_group(struct sock *sk , struct ip_mreqn *imr) struct ip_mc_socklist *iml=NULL, *i; struct in_device *in_dev; struct inet_sock *inet = inet_sk(sk); + struct net *net = sock_net(sk); int ifindex; int count = 0; if (!ipv4_is_multicast(addr)) return -EINVAL; - if (!net_eq(sock_net(sk), &init_net)) - return -EPROTONOSUPPORT; - rtnl_lock(); - in_dev = ip_mc_find_dev(imr); + in_dev = ip_mc_find_dev(net, imr); if (!in_dev) { iml = NULL; @@ -1827,15 +1809,13 @@ int ip_mc_leave_group(struct sock *sk, struct ip_mreqn *imr) struct inet_sock *inet = inet_sk(sk); struct ip_mc_socklist *iml, **imlp; struct in_device *in_dev; + struct net *net = sock_net(sk); __be32 group = imr->imr_multiaddr.s_addr; u32 ifindex; int ret = -EADDRNOTAVAIL; - if (!net_eq(sock_net(sk), &init_net)) - return -EPROTONOSUPPORT; - rtnl_lock(); - in_dev = ip_mc_find_dev(imr); + in_dev = ip_mc_find_dev(net, imr); ifindex = imr->imr_ifindex; for (imlp = &inet->mc_list; (iml = *imlp) != NULL; imlp = &iml->next) { if (iml->multi.imr_multiaddr.s_addr != group) @@ -1873,21 +1853,19 @@ int ip_mc_source(int add, int omode, struct sock *sk, struct struct in_device *in_dev = NULL; struct inet_sock *inet = inet_sk(sk); struct ip_sf_socklist *psl; + struct net *net = sock_net(sk); int leavegroup = 0; int i, j, rv; if (!ipv4_is_multicast(addr)) return -EINVAL; - if (!net_eq(sock_net(sk), &init_net)) - return -EPROTONOSUPPORT; - rtnl_lock(); imr.imr_multiaddr.s_addr = mreqs->imr_multiaddr; imr.imr_address.s_addr = mreqs->imr_interface; imr.imr_ifindex = ifindex; - in_dev = ip_mc_find_dev(&imr); + in_dev = ip_mc_find_dev(net, &imr); if (!in_dev) { err = -ENODEV; @@ -2007,6 +1985,7 @@ int ip_mc_msfilter(struct sock *sk, struct ip_msfilter *msf, int ifindex) struct in_device *in_dev; struct inet_sock *inet = inet_sk(sk); struct ip_sf_socklist *newpsl, *psl; + struct net *net = sock_net(sk); int leavegroup = 0; if (!ipv4_is_multicast(addr)) @@ -2015,15 +1994,12 @@ int ip_mc_msfilter(struct sock *sk, struct ip_msfilter *msf, int ifindex) msf->imsf_fmode != MCAST_EXCLUDE) return -EINVAL; - if (!net_eq(sock_net(sk), &init_net)) - return -EPROTONOSUPPORT; - rtnl_lock(); imr.imr_multiaddr.s_addr = msf->imsf_multiaddr; imr.imr_address.s_addr = msf->imsf_interface; imr.imr_ifindex = ifindex; - in_dev = ip_mc_find_dev(&imr); + in_dev = ip_mc_find_dev(net, &imr); if (!in_dev) { err = -ENODEV; @@ -2094,19 +2070,17 @@ int ip_mc_msfget(struct sock *sk, struct ip_msfilter *msf, struct in_device *in_dev; struct inet_sock *inet = inet_sk(sk); struct ip_sf_socklist *psl; + struct net *net = sock_net(sk); if (!ipv4_is_multicast(addr)) return -EINVAL; - if (!net_eq(sock_net(sk), &init_net)) - return -EPROTONOSUPPORT; - rtnl_lock(); imr.imr_multiaddr.s_addr = msf->imsf_multiaddr; imr.imr_address.s_addr = msf->imsf_interface; imr.imr_ifindex = 0; - in_dev = ip_mc_find_dev(&imr); + in_dev = ip_mc_find_dev(net, &imr); if (!in_dev) { err = -ENODEV; @@ -2163,9 +2137,6 @@ int ip_mc_gsfget(struct sock *sk, struct group_filter *gsf, if (!ipv4_is_multicast(addr)) return -EINVAL; - if (!net_eq(sock_net(sk), &init_net)) - return -EPROTONOSUPPORT; - rtnl_lock(); err = -EADDRNOTAVAIL; @@ -2246,19 +2217,17 @@ void ip_mc_drop_socket(struct sock *sk) { struct inet_sock *inet = inet_sk(sk); struct ip_mc_socklist *iml; + struct net *net = sock_net(sk); if (inet->mc_list == NULL) return; - if (!net_eq(sock_net(sk), &init_net)) - return; - rtnl_lock(); while ((iml = inet->mc_list) != NULL) { struct in_device *in_dev; inet->mc_list = iml->next; - in_dev = inetdev_by_index(&init_net, iml->multi.imr_ifindex); + in_dev = inetdev_by_index(net, iml->multi.imr_ifindex); (void) ip_mc_leave_src(sk, iml, in_dev); if (in_dev != NULL) { ip_mc_dec_group(in_dev, iml->multi.imr_multiaddr.s_addr); -- GitLab From 9e2b2dc4133f65272a6d3c5dcb2ce63f8a87cae9 Mon Sep 17 00:00:00 2001 From: David Howells Date: Wed, 13 Aug 2008 16:20:04 +0100 Subject: [PATCH 270/750] CRED: Introduce credential access wrappers The patches that are intended to introduce copy-on-write credentials for 2.6.28 require abstraction of access to some fields of the task structure, particularly for the case of one task accessing another's credentials where RCU will have to be observed. Introduced here are trivial no-op versions of the desired accessors for current and other tasks so that other subsystems can start to be converted over more easily. Wrappers are introduced into a new header (linux/cred.h) for UID/GID, EUID/EGID, SUID/SGID, FSUID/FSGID, cap_effective and current's subscribed user_struct. These wrappers are macros because the ordering between header files mitigates against making them inline functions. linux/cred.h is #included from linux/sched.h. Further, XFS is modified such that it no longer defines and uses parameterised versions of current_fs[ug]id(), thus getting rid of the namespace collision otherwise incurred. Signed-off-by: David Howells Signed-off-by: James Morris --- fs/xfs/linux-2.6/xfs_linux.h | 2 -- fs/xfs/xfs_inode.c | 4 +-- fs/xfs/xfs_vnodeops.c | 8 +++--- include/linux/cred.h | 50 ++++++++++++++++++++++++++++++++++++ include/linux/sched.h | 1 + 5 files changed, 57 insertions(+), 8 deletions(-) create mode 100644 include/linux/cred.h diff --git a/fs/xfs/linux-2.6/xfs_linux.h b/fs/xfs/linux-2.6/xfs_linux.h index 3b7c4ff48ba..cc0f7b3a979 100644 --- a/fs/xfs/linux-2.6/xfs_linux.h +++ b/fs/xfs/linux-2.6/xfs_linux.h @@ -126,8 +126,6 @@ #define current_cpu() (raw_smp_processor_id()) #define current_pid() (current->pid) -#define current_fsuid(cred) (current->fsuid) -#define current_fsgid(cred) (current->fsgid) #define current_test_flags(f) (current->flags & (f)) #define current_set_flags_nested(sp, f) \ (*(sp) = current->flags, current->flags |= (f)) diff --git a/fs/xfs/xfs_inode.c b/fs/xfs/xfs_inode.c index 358511b85ce..00e80df9dd9 100644 --- a/fs/xfs/xfs_inode.c +++ b/fs/xfs/xfs_inode.c @@ -1081,8 +1081,8 @@ xfs_ialloc( ip->i_d.di_onlink = 0; ip->i_d.di_nlink = nlink; ASSERT(ip->i_d.di_nlink == nlink); - ip->i_d.di_uid = current_fsuid(cr); - ip->i_d.di_gid = current_fsgid(cr); + ip->i_d.di_uid = current_fsuid(); + ip->i_d.di_gid = current_fsgid(); ip->i_d.di_projid = prid; memset(&(ip->i_d.di_pad[0]), 0, sizeof(ip->i_d.di_pad)); diff --git a/fs/xfs/xfs_vnodeops.c b/fs/xfs/xfs_vnodeops.c index 588bb4aa215..aa238c8fbd7 100644 --- a/fs/xfs/xfs_vnodeops.c +++ b/fs/xfs/xfs_vnodeops.c @@ -182,7 +182,7 @@ xfs_setattr( xfs_ilock(ip, lock_flags); /* boolean: are we the file owner? */ - file_owner = (current_fsuid(credp) == ip->i_d.di_uid); + file_owner = (current_fsuid() == ip->i_d.di_uid); /* * Change various properties of a file. @@ -1533,7 +1533,7 @@ xfs_create( * Make sure that we have allocated dquot(s) on disk. */ error = XFS_QM_DQVOPALLOC(mp, dp, - current_fsuid(credp), current_fsgid(credp), prid, + current_fsuid(), current_fsgid(), prid, XFS_QMOPT_QUOTALL|XFS_QMOPT_INHERIT, &udqp, &gdqp); if (error) goto std_return; @@ -2269,7 +2269,7 @@ xfs_mkdir( * Make sure that we have allocated dquot(s) on disk. */ error = XFS_QM_DQVOPALLOC(mp, dp, - current_fsuid(credp), current_fsgid(credp), prid, + current_fsuid(), current_fsgid(), prid, XFS_QMOPT_QUOTALL | XFS_QMOPT_INHERIT, &udqp, &gdqp); if (error) goto std_return; @@ -2495,7 +2495,7 @@ xfs_symlink( * Make sure that we have allocated dquot(s) on disk. */ error = XFS_QM_DQVOPALLOC(mp, dp, - current_fsuid(credp), current_fsgid(credp), prid, + current_fsuid(), current_fsgid(), prid, XFS_QMOPT_QUOTALL | XFS_QMOPT_INHERIT, &udqp, &gdqp); if (error) goto std_return; diff --git a/include/linux/cred.h b/include/linux/cred.h new file mode 100644 index 00000000000..b69222cc1fd --- /dev/null +++ b/include/linux/cred.h @@ -0,0 +1,50 @@ +/* Credentials management + * + * Copyright (C) 2008 Red Hat, Inc. All Rights Reserved. + * Written by David Howells (dhowells@redhat.com) + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public Licence + * as published by the Free Software Foundation; either version + * 2 of the Licence, or (at your option) any later version. + */ + +#ifndef _LINUX_CRED_H +#define _LINUX_CRED_H + +#define get_current_user() (get_uid(current->user)) + +#define task_uid(task) ((task)->uid) +#define task_gid(task) ((task)->gid) +#define task_euid(task) ((task)->euid) +#define task_egid(task) ((task)->egid) + +#define current_uid() (current->uid) +#define current_gid() (current->gid) +#define current_euid() (current->euid) +#define current_egid() (current->egid) +#define current_suid() (current->suid) +#define current_sgid() (current->sgid) +#define current_fsuid() (current->fsuid) +#define current_fsgid() (current->fsgid) +#define current_cap() (current->cap_effective) + +#define current_uid_gid(_uid, _gid) \ +do { \ + *(_uid) = current->uid; \ + *(_gid) = current->gid; \ +} while(0) + +#define current_euid_egid(_uid, _gid) \ +do { \ + *(_uid) = current->euid; \ + *(_gid) = current->egid; \ +} while(0) + +#define current_fsuid_fsgid(_uid, _gid) \ +do { \ + *(_uid) = current->fsuid; \ + *(_gid) = current->fsgid; \ +} while(0) + +#endif /* _LINUX_CRED_H */ diff --git a/include/linux/sched.h b/include/linux/sched.h index 5850bfb968a..cfb0d87b99f 100644 --- a/include/linux/sched.h +++ b/include/linux/sched.h @@ -87,6 +87,7 @@ struct sched_param { #include #include #include +#include #include -- GitLab From 6f63e781eaf6a741fc65f773017154b20ed4ce3b Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Wed, 13 Aug 2008 17:17:52 -0700 Subject: [PATCH 271/750] sparc64: Handle stack trace attempts before irqstacks are setup. Things like lockdep can try to do stack backtraces before the irqstack blocks have been setup. So don't try to match their ranges so early on. Also, remove unused variable in save_stack_trace(). Signed-off-by: David S. Miller --- arch/sparc64/kernel/kstack.h | 38 +++++++++++++++++--------------- arch/sparc64/kernel/stacktrace.c | 3 +-- 2 files changed, 21 insertions(+), 20 deletions(-) diff --git a/arch/sparc64/kernel/kstack.h b/arch/sparc64/kernel/kstack.h index 43909d5680e..4248d969272 100644 --- a/arch/sparc64/kernel/kstack.h +++ b/arch/sparc64/kernel/kstack.h @@ -15,15 +15,16 @@ static inline bool kstack_valid(struct thread_info *tp, unsigned long sp) sp <= (base + THREAD_SIZE - sizeof(struct sparc_stackf))) return true; - base = (unsigned long) hardirq_stack[tp->cpu]; - if (sp >= base && - sp <= (base + THREAD_SIZE - sizeof(struct sparc_stackf))) - return true; - base = (unsigned long) softirq_stack[tp->cpu]; - if (sp >= base && - sp <= (base + THREAD_SIZE - sizeof(struct sparc_stackf))) - return true; - + if (hardirq_stack[tp->cpu]) { + base = (unsigned long) hardirq_stack[tp->cpu]; + if (sp >= base && + sp <= (base + THREAD_SIZE - sizeof(struct sparc_stackf))) + return true; + base = (unsigned long) softirq_stack[tp->cpu]; + if (sp >= base && + sp <= (base + THREAD_SIZE - sizeof(struct sparc_stackf))) + return true; + } return false; } @@ -37,15 +38,16 @@ static inline bool kstack_is_trap_frame(struct thread_info *tp, struct pt_regs * addr <= (base + THREAD_SIZE - sizeof(*regs))) goto check_magic; - base = (unsigned long) hardirq_stack[tp->cpu]; - if (addr >= base && - addr <= (base + THREAD_SIZE - sizeof(*regs))) - goto check_magic; - base = (unsigned long) softirq_stack[tp->cpu]; - if (addr >= base && - addr <= (base + THREAD_SIZE - sizeof(*regs))) - goto check_magic; - + if (hardirq_stack[tp->cpu]) { + base = (unsigned long) hardirq_stack[tp->cpu]; + if (addr >= base && + addr <= (base + THREAD_SIZE - sizeof(*regs))) + goto check_magic; + base = (unsigned long) softirq_stack[tp->cpu]; + if (addr >= base && + addr <= (base + THREAD_SIZE - sizeof(*regs))) + goto check_magic; + } return false; check_magic: diff --git a/arch/sparc64/kernel/stacktrace.c b/arch/sparc64/kernel/stacktrace.c index 237e7f8a40a..4e21d4a57d3 100644 --- a/arch/sparc64/kernel/stacktrace.c +++ b/arch/sparc64/kernel/stacktrace.c @@ -9,8 +9,8 @@ void save_stack_trace(struct stack_trace *trace) { - unsigned long ksp, fp, thread_base; struct thread_info *tp = task_thread_info(current); + unsigned long ksp, fp; stack_trace_flush(); @@ -20,7 +20,6 @@ void save_stack_trace(struct stack_trace *trace) ); fp = ksp + STACK_BIAS; - thread_base = (unsigned long) tp; do { struct sparc_stackf *sf; struct pt_regs *regs; -- GitLab From 88d987d6db2a14b191f4eb21cc623dae31e28e9d Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Wolfgang=20M=C3=BCes?= Date: Tue, 29 Jul 2008 11:54:43 +0200 Subject: [PATCH 272/750] usb: auerswald: remove driver (obsolete) This patch removes the auerswald USB driver from the linux kernel 2.6.26. This driver was included into the kernel mainly to connect to the ISDN framework. This was done in linux 2.4.x. For 2.6.x, due to the fragile and moving ISDN support, this connection was never realized, and the only use of this driver was for device configuration. In the age of DSL, the demand of ISDN support is getting very low. Meanwhile, with the advent of libusb, an userspace driver was done for the device configuration which works fine for linux and mac. (Thanks to the libusb developers!). The userspace driver is downloadable from the auerswald web site. So this driver is obsolete now and has to be removed. Many thanks to all developers which helped me to bring this driver up and working. Signed-off-by: Wolfgang Muees Signed-off-by: Greg Kroah-Hartman --- Documentation/devices.txt | 3 - Documentation/ioctl-number.txt | 1 - Documentation/usb/auerswald.txt | 30 - MAINTAINERS | 6 - drivers/usb/misc/Kconfig | 10 - drivers/usb/misc/Makefile | 1 - drivers/usb/misc/auerswald.c | 2152 ------------------------------- 7 files changed, 2203 deletions(-) delete mode 100644 Documentation/usb/auerswald.txt delete mode 100644 drivers/usb/misc/auerswald.c diff --git a/Documentation/devices.txt b/Documentation/devices.txt index e6244cde26e..05c80645e4e 100644 --- a/Documentation/devices.txt +++ b/Documentation/devices.txt @@ -2560,9 +2560,6 @@ Your cooperation is appreciated. 96 = /dev/usb/hiddev0 1st USB HID device ... 111 = /dev/usb/hiddev15 16th USB HID device - 112 = /dev/usb/auer0 1st auerswald ISDN device - ... - 127 = /dev/usb/auer15 16th auerswald ISDN device 128 = /dev/usb/brlvgr0 First Braille Voyager device ... 131 = /dev/usb/brlvgr3 Fourth Braille Voyager device diff --git a/Documentation/ioctl-number.txt b/Documentation/ioctl-number.txt index 3bb5f466a90..1c6b545635a 100644 --- a/Documentation/ioctl-number.txt +++ b/Documentation/ioctl-number.txt @@ -105,7 +105,6 @@ Code Seq# Include File Comments 'T' all linux/soundcard.h conflict! 'T' all asm-i386/ioctls.h conflict! 'U' 00-EF linux/drivers/usb/usb.h -'U' F0-FF drivers/usb/auerswald.c 'V' all linux/vt.h 'W' 00-1F linux/watchdog.h conflict! 'W' 00-1F linux/wanrouter.h conflict! diff --git a/Documentation/usb/auerswald.txt b/Documentation/usb/auerswald.txt deleted file mode 100644 index 7ee4d8f6911..00000000000 --- a/Documentation/usb/auerswald.txt +++ /dev/null @@ -1,30 +0,0 @@ - Auerswald USB kernel driver - =========================== - -What is it? What can I do with it? -================================== -The auerswald USB kernel driver connects your linux 2.4.x -system to the auerswald usb-enabled devices. - -There are two types of auerswald usb devices: -a) small PBX systems (ISDN) -b) COMfort system telephones (ISDN) - -The driver installation creates the devices -/dev/usb/auer0..15. These devices carry a vendor- -specific protocol. You may run all auerswald java -software on it. The java software needs a native -library "libAuerUsbJNINative.so" installed on -your system. This library is available from -auerswald and shipped as part of the java software. - -You may create the devices with: - mknod -m 666 /dev/usb/auer0 c 180 112 - ... - mknod -m 666 /dev/usb/auer15 c 180 127 - -Future plans -============ -- Connection to ISDN4LINUX (the hisax interface) - -The maintainer of this driver is wolfgang@iksw-muees.de diff --git a/MAINTAINERS b/MAINTAINERS index af6aa4e4b39..0c42dc25e0e 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -4195,12 +4195,6 @@ M: oliver@neukum.name L: linux-usb@vger.kernel.org S: Maintained -USB AUERSWALD DRIVER -P: Wolfgang Muees -M: wolfgang@iksw-muees.de -L: linux-usb@vger.kernel.org -S: Maintained - USB BLOCK DRIVER (UB ub) P: Pete Zaitcev M: zaitcev@redhat.com diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig index 001789c9a11..4ea50e0abcb 100644 --- a/drivers/usb/misc/Kconfig +++ b/drivers/usb/misc/Kconfig @@ -42,16 +42,6 @@ config USB_ADUTUX To compile this driver as a module, choose M here. The module will be called adutux. -config USB_AUERSWALD - tristate "USB Auerswald ISDN support" - depends on USB - help - Say Y here if you want to connect an Auerswald USB ISDN Device - to your computer's USB port. - - To compile this driver as a module, choose M here: the - module will be called auerswald. - config USB_RIO500 tristate "USB Diamond Rio500 support" depends on USB diff --git a/drivers/usb/misc/Makefile b/drivers/usb/misc/Makefile index aba091cb5ec..45b4e12afb0 100644 --- a/drivers/usb/misc/Makefile +++ b/drivers/usb/misc/Makefile @@ -5,7 +5,6 @@ obj-$(CONFIG_USB_ADUTUX) += adutux.o obj-$(CONFIG_USB_APPLEDISPLAY) += appledisplay.o -obj-$(CONFIG_USB_AUERSWALD) += auerswald.o obj-$(CONFIG_USB_BERRY_CHARGE) += berry_charge.o obj-$(CONFIG_USB_CYPRESS_CY7C63)+= cypress_cy7c63.o obj-$(CONFIG_USB_CYTHERM) += cytherm.o diff --git a/drivers/usb/misc/auerswald.c b/drivers/usb/misc/auerswald.c deleted file mode 100644 index d2f61d5510e..00000000000 --- a/drivers/usb/misc/auerswald.c +++ /dev/null @@ -1,2152 +0,0 @@ -/*****************************************************************************/ -/* - * auerswald.c -- Auerswald PBX/System Telephone usb driver. - * - * Copyright (C) 2001 Wolfgang Mües (wolfgang@iksw-muees.de) - * - * Very much code of this driver is borrowed from dabusb.c (Deti Fliegl) - * and from the USB Skeleton driver (Greg Kroah-Hartman). Thank you. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - */ - /*****************************************************************************/ - -/* Standard Linux module include files */ -#include -#include -#include -#include -#include -#include -#include -#include - -/*-------------------------------------------------------------------*/ -/* Debug support */ -#ifdef DEBUG -#define dump( adr, len) \ -do { \ - unsigned int u; \ - printk (KERN_DEBUG); \ - for (u = 0; u < len; u++) \ - printk (" %02X", adr[u] & 0xFF); \ - printk ("\n"); \ -} while (0) -#else -#define dump( adr, len) -#endif - -/*-------------------------------------------------------------------*/ -/* Version Information */ -#define DRIVER_VERSION "0.9.11" -#define DRIVER_AUTHOR "Wolfgang Mües " -#define DRIVER_DESC "Auerswald PBX/System Telephone usb driver" - -/*-------------------------------------------------------------------*/ -/* Private declarations for Auerswald USB driver */ - -/* Auerswald Vendor ID */ -#define ID_AUERSWALD 0x09BF - -#define AUER_MINOR_BASE 112 /* auerswald driver minor number */ - -/* we can have up to this number of device plugged in at once */ -#define AUER_MAX_DEVICES 16 - - -/* Number of read buffers for each device */ -#define AU_RBUFFERS 10 - -/* Number of chain elements for each control chain */ -#define AUCH_ELEMENTS 20 - -/* Number of retries in communication */ -#define AU_RETRIES 10 - -/*-------------------------------------------------------------------*/ -/* vendor specific protocol */ -/* Header Byte */ -#define AUH_INDIRMASK 0x80 /* mask for direct/indirect bit */ -#define AUH_DIRECT 0x00 /* data is for USB device */ -#define AUH_INDIRECT 0x80 /* USB device is relay */ - -#define AUH_SPLITMASK 0x40 /* mask for split bit */ -#define AUH_UNSPLIT 0x00 /* data block is full-size */ -#define AUH_SPLIT 0x40 /* data block is part of a larger one, - split-byte follows */ - -#define AUH_TYPEMASK 0x3F /* mask for type of data transfer */ -#define AUH_TYPESIZE 0x40 /* different types */ -#define AUH_DCHANNEL 0x00 /* D channel data */ -#define AUH_B1CHANNEL 0x01 /* B1 channel transparent */ -#define AUH_B2CHANNEL 0x02 /* B2 channel transparent */ -/* 0x03..0x0F reserved for driver internal use */ -#define AUH_COMMAND 0x10 /* Command channel */ -#define AUH_BPROT 0x11 /* Configuration block protocol */ -#define AUH_DPROTANA 0x12 /* D channel protocol analyzer */ -#define AUH_TAPI 0x13 /* telephone api data (ATD) */ -/* 0x14..0x3F reserved for other protocols */ -#define AUH_UNASSIGNED 0xFF /* if char device has no assigned service */ -#define AUH_FIRSTUSERCH 0x11 /* first channel which is available for driver users */ - -#define AUH_SIZE 1 /* Size of Header Byte */ - -/* Split Byte. Only present if split bit in header byte set.*/ -#define AUS_STARTMASK 0x80 /* mask for first block of splitted frame */ -#define AUS_FIRST 0x80 /* first block */ -#define AUS_FOLLOW 0x00 /* following block */ - -#define AUS_ENDMASK 0x40 /* mask for last block of splitted frame */ -#define AUS_END 0x40 /* last block */ -#define AUS_NOEND 0x00 /* not the last block */ - -#define AUS_LENMASK 0x3F /* mask for block length information */ - -/* Request types */ -#define AUT_RREQ (USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_OTHER) /* Read Request */ -#define AUT_WREQ (USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_OTHER) /* Write Request */ - -/* Vendor Requests */ -#define AUV_GETINFO 0x00 /* GetDeviceInfo */ -#define AUV_WBLOCK 0x01 /* Write Block */ -#define AUV_RBLOCK 0x02 /* Read Block */ -#define AUV_CHANNELCTL 0x03 /* Channel Control */ -#define AUV_DUMMY 0x04 /* Dummy Out for retry */ - -/* Device Info Types */ -#define AUDI_NUMBCH 0x0000 /* Number of supported B channels */ -#define AUDI_OUTFSIZE 0x0001 /* Size of OUT B channel fifos */ -#define AUDI_MBCTRANS 0x0002 /* max. Blocklength of control transfer */ - -/* Interrupt endpoint definitions */ -#define AU_IRQENDP 1 /* Endpoint number */ -#define AU_IRQCMDID 16 /* Command-block ID */ -#define AU_BLOCKRDY 0 /* Command: Block data ready on ctl endpoint */ -#define AU_IRQMINSIZE 5 /* Nr. of bytes decoded in this driver */ - -/* Device String Descriptors */ -#define AUSI_VENDOR 1 /* "Auerswald GmbH & Co. KG" */ -#define AUSI_DEVICE 2 /* Name of the Device */ -#define AUSI_SERIALNR 3 /* Serial Number */ -#define AUSI_MSN 4 /* "MSN ..." (first) Multiple Subscriber Number */ - -#define AUSI_DLEN 100 /* Max. Length of Device Description */ - -#define AUV_RETRY 0x101 /* First Firmware version which can do control retries */ - -/*-------------------------------------------------------------------*/ -/* External data structures / Interface */ -typedef struct -{ - char __user *buf; /* return buffer for string contents */ - unsigned int bsize; /* size of return buffer */ -} audevinfo_t,*paudevinfo_t; - -/* IO controls */ -#define IOCTL_AU_SLEN _IOR( 'U', 0xF0, int) /* return the max. string descriptor length */ -#define IOCTL_AU_DEVINFO _IOWR('U', 0xF1, audevinfo_t) /* get name of a specific device */ -#define IOCTL_AU_SERVREQ _IOW( 'U', 0xF2, int) /* request a service channel */ -#define IOCTL_AU_BUFLEN _IOR( 'U', 0xF3, int) /* return the max. buffer length for the device */ -#define IOCTL_AU_RXAVAIL _IOR( 'U', 0xF4, int) /* return != 0 if Receive Data available */ -#define IOCTL_AU_CONNECT _IOR( 'U', 0xF5, int) /* return != 0 if connected to a service channel */ -#define IOCTL_AU_TXREADY _IOR( 'U', 0xF6, int) /* return != 0 if Transmitt channel ready to send */ -/* 'U' 0xF7..0xFF reseved */ - -/*-------------------------------------------------------------------*/ -/* Internal data structures */ - -/* ..................................................................*/ -/* urb chain element */ -struct auerchain; /* forward for circular reference */ -typedef struct -{ - struct auerchain *chain; /* pointer to the chain to which this element belongs */ - struct urb * urbp; /* pointer to attached urb */ - void *context; /* saved URB context */ - usb_complete_t complete; /* saved URB completion function */ - struct list_head list; /* to include element into a list */ -} auerchainelement_t,*pauerchainelement_t; - -/* urb chain */ -typedef struct auerchain -{ - pauerchainelement_t active; /* element which is submitted to urb */ - spinlock_t lock; /* protection agains interrupts */ - struct list_head waiting_list; /* list of waiting elements */ - struct list_head free_list; /* list of available elements */ -} auerchain_t,*pauerchain_t; - -/* urb blocking completion helper struct */ -typedef struct -{ - wait_queue_head_t wqh; /* wait for completion */ - unsigned int done; /* completion flag */ -} auerchain_chs_t,*pauerchain_chs_t; - -/* ...................................................................*/ -/* buffer element */ -struct auerbufctl; /* forward */ -typedef struct -{ - char *bufp; /* reference to allocated data buffer */ - unsigned int len; /* number of characters in data buffer */ - unsigned int retries; /* for urb retries */ - struct usb_ctrlrequest *dr; /* for setup data in control messages */ - struct urb * urbp; /* USB urb */ - struct auerbufctl *list; /* pointer to list */ - struct list_head buff_list; /* reference to next buffer in list */ -} auerbuf_t,*pauerbuf_t; - -/* buffer list control block */ -typedef struct auerbufctl -{ - spinlock_t lock; /* protection in interrupt */ - struct list_head free_buff_list;/* free buffers */ - struct list_head rec_buff_list; /* buffers with receive data */ -} auerbufctl_t,*pauerbufctl_t; - -/* ...................................................................*/ -/* service context */ -struct auerscon; /* forward */ -typedef void (*auer_dispatch_t)(struct auerscon*, pauerbuf_t); -typedef void (*auer_disconn_t) (struct auerscon*); -typedef struct auerscon -{ - unsigned int id; /* protocol service id AUH_xxxx */ - auer_dispatch_t dispatch; /* dispatch read buffer */ - auer_disconn_t disconnect; /* disconnect from device, wake up all char readers */ -} auerscon_t,*pauerscon_t; - -/* ...................................................................*/ -/* USB device context */ -typedef struct -{ - struct mutex mutex; /* protection in user context */ - char name[20]; /* name of the /dev/usb entry */ - unsigned int dtindex; /* index in the device table */ - struct usb_device * usbdev; /* USB device handle */ - int open_count; /* count the number of open character channels */ - char dev_desc[AUSI_DLEN];/* for storing a textual description */ - unsigned int maxControlLength; /* max. Length of control paket (without header) */ - struct urb * inturbp; /* interrupt urb */ - char * intbufp; /* data buffer for interrupt urb */ - unsigned int irqsize; /* size of interrupt endpoint 1 */ - struct auerchain controlchain; /* for chaining of control messages */ - auerbufctl_t bufctl; /* Buffer control for control transfers */ - pauerscon_t services[AUH_TYPESIZE];/* context pointers for each service */ - unsigned int version; /* Version of the device */ - wait_queue_head_t bufferwait; /* wait for a control buffer */ -} auerswald_t,*pauerswald_t; - -/* ................................................................... */ -/* character device context */ -typedef struct -{ - struct mutex mutex; /* protection in user context */ - pauerswald_t auerdev; /* context pointer of assigned device */ - auerbufctl_t bufctl; /* controls the buffer chain */ - auerscon_t scontext; /* service context */ - wait_queue_head_t readwait; /* for synchronous reading */ - struct mutex readmutex; /* protection against multiple reads */ - pauerbuf_t readbuf; /* buffer held for partial reading */ - unsigned int readoffset; /* current offset in readbuf */ - unsigned int removed; /* is != 0 if device is removed */ -} auerchar_t,*pauerchar_t; - - -/*-------------------------------------------------------------------*/ -/* Forwards */ -static void auerswald_ctrlread_complete (struct urb * urb); -static void auerswald_removeservice (pauerswald_t cp, pauerscon_t scp); -static struct usb_driver auerswald_driver; - - -/*-------------------------------------------------------------------*/ -/* USB chain helper functions */ -/* -------------------------- */ - -/* completion function for chained urbs */ -static void auerchain_complete (struct urb * urb) -{ - unsigned long flags; - int result; - - /* get pointer to element and to chain */ - pauerchainelement_t acep = urb->context; - pauerchain_t acp = acep->chain; - - /* restore original entries in urb */ - urb->context = acep->context; - urb->complete = acep->complete; - - dbg ("auerchain_complete called"); - - /* call original completion function - NOTE: this function may lead to more urbs submitted into the chain. - (no chain lock at calling complete()!) - acp->active != NULL is protecting us against recursion.*/ - urb->complete (urb); - - /* detach element from chain data structure */ - spin_lock_irqsave (&acp->lock, flags); - if (acp->active != acep) /* paranoia debug check */ - dbg ("auerchain_complete: completion on non-active element called!"); - else - acp->active = NULL; - - /* add the used chain element to the list of free elements */ - list_add_tail (&acep->list, &acp->free_list); - acep = NULL; - - /* is there a new element waiting in the chain? */ - if (!acp->active && !list_empty (&acp->waiting_list)) { - /* yes: get the entry */ - struct list_head *tmp = acp->waiting_list.next; - list_del (tmp); - acep = list_entry (tmp, auerchainelement_t, list); - acp->active = acep; - } - spin_unlock_irqrestore (&acp->lock, flags); - - /* submit the new urb */ - if (acep) { - urb = acep->urbp; - dbg ("auerchain_complete: submitting next urb from chain"); - urb->status = 0; /* needed! */ - result = usb_submit_urb(urb, GFP_ATOMIC); - - /* check for submit errors */ - if (result) { - urb->status = result; - dbg("auerchain_complete: usb_submit_urb with error code %d", result); - /* and do error handling via *this* completion function (recursive) */ - auerchain_complete( urb); - } - } else { - /* simple return without submitting a new urb. - The empty chain is detected with acp->active == NULL. */ - }; -} - - -/* submit function for chained urbs - this function may be called from completion context or from user space! - early = 1 -> submit in front of chain -*/ -static int auerchain_submit_urb_list (pauerchain_t acp, struct urb * urb, int early) -{ - int result; - unsigned long flags; - pauerchainelement_t acep = NULL; - - dbg ("auerchain_submit_urb called"); - - /* try to get a chain element */ - spin_lock_irqsave (&acp->lock, flags); - if (!list_empty (&acp->free_list)) { - /* yes: get the entry */ - struct list_head *tmp = acp->free_list.next; - list_del (tmp); - acep = list_entry (tmp, auerchainelement_t, list); - } - spin_unlock_irqrestore (&acp->lock, flags); - - /* if no chain element available: return with error */ - if (!acep) { - return -ENOMEM; - } - - /* fill in the new chain element values */ - acep->chain = acp; - acep->context = urb->context; - acep->complete = urb->complete; - acep->urbp = urb; - INIT_LIST_HEAD (&acep->list); - - /* modify urb */ - urb->context = acep; - urb->complete = auerchain_complete; - urb->status = -EINPROGRESS; /* usb_submit_urb does this, too */ - - /* add element to chain - or start it immediately */ - spin_lock_irqsave (&acp->lock, flags); - if (acp->active) { - /* there is traffic in the chain, simple add element to chain */ - if (early) { - dbg ("adding new urb to head of chain"); - list_add (&acep->list, &acp->waiting_list); - } else { - dbg ("adding new urb to end of chain"); - list_add_tail (&acep->list, &acp->waiting_list); - } - acep = NULL; - } else { - /* the chain is empty. Prepare restart */ - acp->active = acep; - } - /* Spin has to be removed before usb_submit_urb! */ - spin_unlock_irqrestore (&acp->lock, flags); - - /* Submit urb if immediate restart */ - if (acep) { - dbg("submitting urb immediate"); - urb->status = 0; /* needed! */ - result = usb_submit_urb(urb, GFP_ATOMIC); - /* check for submit errors */ - if (result) { - urb->status = result; - dbg("auerchain_submit_urb: usb_submit_urb with error code %d", result); - /* and do error handling via completion function */ - auerchain_complete( urb); - } - } - - return 0; -} - -/* submit function for chained urbs - this function may be called from completion context or from user space! -*/ -static int auerchain_submit_urb (pauerchain_t acp, struct urb * urb) -{ - return auerchain_submit_urb_list (acp, urb, 0); -} - -/* cancel an urb which is submitted to the chain - the result is 0 if the urb is cancelled, or -EINPROGRESS if - the function is successfully started. -*/ -static int auerchain_unlink_urb (pauerchain_t acp, struct urb * urb) -{ - unsigned long flags; - struct urb * urbp; - pauerchainelement_t acep; - struct list_head *tmp; - - dbg ("auerchain_unlink_urb called"); - - /* search the chain of waiting elements */ - spin_lock_irqsave (&acp->lock, flags); - list_for_each (tmp, &acp->waiting_list) { - acep = list_entry (tmp, auerchainelement_t, list); - if (acep->urbp == urb) { - list_del (tmp); - urb->context = acep->context; - urb->complete = acep->complete; - list_add_tail (&acep->list, &acp->free_list); - spin_unlock_irqrestore (&acp->lock, flags); - dbg ("unlink waiting urb"); - urb->status = -ENOENT; - urb->complete (urb); - return 0; - } - } - /* not found. */ - spin_unlock_irqrestore (&acp->lock, flags); - - /* get the active urb */ - acep = acp->active; - if (acep) { - urbp = acep->urbp; - - /* check if we have to cancel the active urb */ - if (urbp == urb) { - /* note that there is a race condition between the check above - and the unlink() call because of no lock. This race is harmless, - because the usb module will detect the unlink() after completion. - We can't use the acp->lock here because the completion function - wants to grab it. - */ - dbg ("unlink active urb"); - return usb_unlink_urb (urbp); - } - } - - /* not found anyway - ... is some kind of success - */ - dbg ("urb to unlink not found in chain"); - return 0; -} - -/* cancel all urbs which are in the chain. - this function must not be called from interrupt or completion handler. -*/ -static void auerchain_unlink_all (pauerchain_t acp) -{ - unsigned long flags; - struct urb * urbp; - pauerchainelement_t acep; - - dbg ("auerchain_unlink_all called"); - - /* clear the chain of waiting elements */ - spin_lock_irqsave (&acp->lock, flags); - while (!list_empty (&acp->waiting_list)) { - /* get the next entry */ - struct list_head *tmp = acp->waiting_list.next; - list_del (tmp); - acep = list_entry (tmp, auerchainelement_t, list); - urbp = acep->urbp; - urbp->context = acep->context; - urbp->complete = acep->complete; - list_add_tail (&acep->list, &acp->free_list); - spin_unlock_irqrestore (&acp->lock, flags); - dbg ("unlink waiting urb"); - urbp->status = -ENOENT; - urbp->complete (urbp); - spin_lock_irqsave (&acp->lock, flags); - } - spin_unlock_irqrestore (&acp->lock, flags); - - /* clear the active urb */ - acep = acp->active; - if (acep) { - urbp = acep->urbp; - dbg ("unlink active urb"); - usb_kill_urb (urbp); - } -} - - -/* free the chain. - this function must not be called from interrupt or completion handler. -*/ -static void auerchain_free (pauerchain_t acp) -{ - unsigned long flags; - pauerchainelement_t acep; - - dbg ("auerchain_free called"); - - /* first, cancel all pending urbs */ - auerchain_unlink_all (acp); - - /* free the elements */ - spin_lock_irqsave (&acp->lock, flags); - while (!list_empty (&acp->free_list)) { - /* get the next entry */ - struct list_head *tmp = acp->free_list.next; - list_del (tmp); - spin_unlock_irqrestore (&acp->lock, flags); - acep = list_entry (tmp, auerchainelement_t, list); - kfree (acep); - spin_lock_irqsave (&acp->lock, flags); - } - spin_unlock_irqrestore (&acp->lock, flags); -} - - -/* Init the chain control structure */ -static void auerchain_init (pauerchain_t acp) -{ - /* init the chain data structure */ - acp->active = NULL; - spin_lock_init (&acp->lock); - INIT_LIST_HEAD (&acp->waiting_list); - INIT_LIST_HEAD (&acp->free_list); -} - -/* setup a chain. - It is assumed that there is no concurrency while setting up the chain - requirement: auerchain_init() -*/ -static int auerchain_setup (pauerchain_t acp, unsigned int numElements) -{ - pauerchainelement_t acep; - - dbg ("auerchain_setup called with %d elements", numElements); - - /* fill the list of free elements */ - for (;numElements; numElements--) { - acep = kzalloc(sizeof(auerchainelement_t), GFP_KERNEL); - if (!acep) - goto ac_fail; - INIT_LIST_HEAD (&acep->list); - list_add_tail (&acep->list, &acp->free_list); - } - return 0; - -ac_fail:/* free the elements */ - while (!list_empty (&acp->free_list)) { - /* get the next entry */ - struct list_head *tmp = acp->free_list.next; - list_del (tmp); - acep = list_entry (tmp, auerchainelement_t, list); - kfree (acep); - } - return -ENOMEM; -} - - -/* completion handler for synchronous chained URBs */ -static void auerchain_blocking_completion (struct urb *urb) -{ - pauerchain_chs_t pchs = urb->context; - pchs->done = 1; - wmb(); - wake_up (&pchs->wqh); -} - - -/* Starts chained urb and waits for completion or timeout */ -static int auerchain_start_wait_urb (pauerchain_t acp, struct urb *urb, int timeout, int* actual_length) -{ - auerchain_chs_t chs; - int status; - - dbg ("auerchain_start_wait_urb called"); - init_waitqueue_head (&chs.wqh); - chs.done = 0; - - urb->context = &chs; - status = auerchain_submit_urb (acp, urb); - if (status) - /* something went wrong */ - return status; - - timeout = wait_event_timeout(chs.wqh, chs.done, timeout); - - if (!timeout && !chs.done) { - if (urb->status != -EINPROGRESS) { /* No callback?!! */ - dbg ("auerchain_start_wait_urb: raced timeout"); - status = urb->status; - } else { - dbg ("auerchain_start_wait_urb: timeout"); - auerchain_unlink_urb (acp, urb); /* remove urb safely */ - status = -ETIMEDOUT; - } - } else - status = urb->status; - - if (status >= 0) - *actual_length = urb->actual_length; - - return status; -} - - -/* auerchain_control_msg - Builds a control urb, sends it off and waits for completion - acp: pointer to the auerchain - dev: pointer to the usb device to send the message to - pipe: endpoint "pipe" to send the message to - request: USB message request value - requesttype: USB message request type value - value: USB message value - index: USB message index value - data: pointer to the data to send - size: length in bytes of the data to send - timeout: time to wait for the message to complete before timing out (if 0 the wait is forever) - - This function sends a simple control message to a specified endpoint - and waits for the message to complete, or timeout. - - If successful, it returns the transferred length, otherwise a negative error number. - - Don't use this function from within an interrupt context, like a - bottom half handler. If you need an asynchronous message, or need to send - a message from within interrupt context, use auerchain_submit_urb() -*/ -static int auerchain_control_msg (pauerchain_t acp, struct usb_device *dev, unsigned int pipe, __u8 request, __u8 requesttype, - __u16 value, __u16 index, void *data, __u16 size, int timeout) -{ - int ret; - struct usb_ctrlrequest *dr; - struct urb *urb; - int uninitialized_var(length); - - dbg ("auerchain_control_msg"); - dr = kmalloc (sizeof (struct usb_ctrlrequest), GFP_KERNEL); - if (!dr) - return -ENOMEM; - urb = usb_alloc_urb (0, GFP_KERNEL); - if (!urb) { - kfree (dr); - return -ENOMEM; - } - - dr->bRequestType = requesttype; - dr->bRequest = request; - dr->wValue = cpu_to_le16 (value); - dr->wIndex = cpu_to_le16 (index); - dr->wLength = cpu_to_le16 (size); - - usb_fill_control_urb (urb, dev, pipe, (unsigned char*)dr, data, size, /* build urb */ - auerchain_blocking_completion, NULL); - ret = auerchain_start_wait_urb (acp, urb, timeout, &length); - - usb_free_urb (urb); - kfree (dr); - - if (ret < 0) - return ret; - else - return length; -} - - -/*-------------------------------------------------------------------*/ -/* Buffer List helper functions */ - -/* free a single auerbuf */ -static void auerbuf_free (pauerbuf_t bp) -{ - kfree(bp->bufp); - kfree(bp->dr); - usb_free_urb(bp->urbp); - kfree(bp); -} - -/* free the buffers from an auerbuf list */ -static void auerbuf_free_list (struct list_head *q) -{ - struct list_head *tmp; - struct list_head *p; - pauerbuf_t bp; - - dbg ("auerbuf_free_list"); - for (p = q->next; p != q;) { - bp = list_entry (p, auerbuf_t, buff_list); - tmp = p->next; - list_del (p); - p = tmp; - auerbuf_free (bp); - } -} - -/* init the members of a list control block */ -static void auerbuf_init (pauerbufctl_t bcp) -{ - dbg ("auerbuf_init"); - spin_lock_init (&bcp->lock); - INIT_LIST_HEAD (&bcp->free_buff_list); - INIT_LIST_HEAD (&bcp->rec_buff_list); -} - -/* free all buffers from an auerbuf chain */ -static void auerbuf_free_buffers (pauerbufctl_t bcp) -{ - unsigned long flags; - dbg ("auerbuf_free_buffers"); - - spin_lock_irqsave (&bcp->lock, flags); - - auerbuf_free_list (&bcp->free_buff_list); - auerbuf_free_list (&bcp->rec_buff_list); - - spin_unlock_irqrestore (&bcp->lock, flags); -} - -/* setup a list of buffers */ -/* requirement: auerbuf_init() */ -static int auerbuf_setup (pauerbufctl_t bcp, unsigned int numElements, unsigned int bufsize) -{ - pauerbuf_t bep = NULL; - - dbg ("auerbuf_setup called with %d elements of %d bytes", numElements, bufsize); - - /* fill the list of free elements */ - for (;numElements; numElements--) { - bep = kzalloc(sizeof(auerbuf_t), GFP_KERNEL); - if (!bep) - goto bl_fail; - bep->list = bcp; - INIT_LIST_HEAD (&bep->buff_list); - bep->bufp = kmalloc (bufsize, GFP_KERNEL); - if (!bep->bufp) - goto bl_fail; - bep->dr = kmalloc(sizeof (struct usb_ctrlrequest), GFP_KERNEL); - if (!bep->dr) - goto bl_fail; - bep->urbp = usb_alloc_urb (0, GFP_KERNEL); - if (!bep->urbp) - goto bl_fail; - list_add_tail (&bep->buff_list, &bcp->free_buff_list); - } - return 0; - -bl_fail:/* not enough memory. Free allocated elements */ - dbg ("auerbuf_setup: no more memory"); - auerbuf_free(bep); - auerbuf_free_buffers (bcp); - return -ENOMEM; -} - -/* insert a used buffer into the free list */ -static void auerbuf_releasebuf( pauerbuf_t bp) -{ - unsigned long flags; - pauerbufctl_t bcp = bp->list; - bp->retries = 0; - - dbg ("auerbuf_releasebuf called"); - spin_lock_irqsave (&bcp->lock, flags); - list_add_tail (&bp->buff_list, &bcp->free_buff_list); - spin_unlock_irqrestore (&bcp->lock, flags); -} - - -/*-------------------------------------------------------------------*/ -/* Completion handlers */ - -/* Values of urb->status or results of usb_submit_urb(): -0 Initial, OK --EINPROGRESS during submission until end --ENOENT if urb is unlinked --ETIME Device did not respond --ENOMEM Memory Overflow --ENODEV Specified USB-device or bus doesn't exist --ENXIO URB already queued --EINVAL a) Invalid transfer type specified (or not supported) - b) Invalid interrupt interval (0n256) --EAGAIN a) Specified ISO start frame too early - b) (using ISO-ASAP) Too much scheduled for the future wait some time and try again. --EFBIG Too much ISO frames requested (currently uhci900) --EPIPE Specified pipe-handle/Endpoint is already stalled --EMSGSIZE Endpoint message size is zero, do interface/alternate setting --EPROTO a) Bitstuff error - b) Unknown USB error --EILSEQ CRC mismatch --ENOSR Buffer error --EREMOTEIO Short packet detected --EXDEV ISO transfer only partially completed look at individual frame status for details --EINVAL ISO madness, if this happens: Log off and go home --EOVERFLOW babble -*/ - -/* check if a status code allows a retry */ -static int auerswald_status_retry (int status) -{ - switch (status) { - case 0: - case -ETIME: - case -EOVERFLOW: - case -EAGAIN: - case -EPIPE: - case -EPROTO: - case -EILSEQ: - case -ENOSR: - case -EREMOTEIO: - return 1; /* do a retry */ - } - return 0; /* no retry possible */ -} - -/* Completion of asynchronous write block */ -static void auerchar_ctrlwrite_complete (struct urb * urb) -{ - pauerbuf_t bp = urb->context; - pauerswald_t cp = ((pauerswald_t)((char *)(bp->list)-(unsigned long)(&((pauerswald_t)0)->bufctl))); - dbg ("auerchar_ctrlwrite_complete called"); - - /* reuse the buffer */ - auerbuf_releasebuf (bp); - /* Wake up all processes waiting for a buffer */ - wake_up (&cp->bufferwait); -} - -/* Completion handler for dummy retry packet */ -static void auerswald_ctrlread_wretcomplete (struct urb * urb) -{ - pauerbuf_t bp = urb->context; - pauerswald_t cp; - int ret; - int status = urb->status; - - dbg ("auerswald_ctrlread_wretcomplete called"); - dbg ("complete with status: %d", status); - cp = ((pauerswald_t)((char *)(bp->list)-(unsigned long)(&((pauerswald_t)0)->bufctl))); - - /* check if it is possible to advance */ - if (!auerswald_status_retry(status) || !cp->usbdev) { - /* reuse the buffer */ - err ("control dummy: transmission error %d, can not retry", status); - auerbuf_releasebuf (bp); - /* Wake up all processes waiting for a buffer */ - wake_up (&cp->bufferwait); - return; - } - - /* fill the control message */ - bp->dr->bRequestType = AUT_RREQ; - bp->dr->bRequest = AUV_RBLOCK; - bp->dr->wLength = bp->dr->wValue; /* temporary stored */ - bp->dr->wValue = cpu_to_le16 (1); /* Retry Flag */ - /* bp->dr->index = channel id; remains */ - usb_fill_control_urb (bp->urbp, cp->usbdev, usb_rcvctrlpipe (cp->usbdev, 0), - (unsigned char*)bp->dr, bp->bufp, le16_to_cpu (bp->dr->wLength), - auerswald_ctrlread_complete,bp); - - /* submit the control msg as next paket */ - ret = auerchain_submit_urb_list (&cp->controlchain, bp->urbp, 1); - if (ret) { - dbg ("auerswald_ctrlread_complete: nonzero result of auerchain_submit_urb_list %d", ret); - bp->urbp->status = ret; - auerswald_ctrlread_complete (bp->urbp); - } -} - -/* completion handler for receiving of control messages */ -static void auerswald_ctrlread_complete (struct urb * urb) -{ - unsigned int serviceid; - pauerswald_t cp; - pauerscon_t scp; - pauerbuf_t bp = urb->context; - int status = urb->status; - int ret; - - dbg ("auerswald_ctrlread_complete called"); - - cp = ((pauerswald_t)((char *)(bp->list)-(unsigned long)(&((pauerswald_t)0)->bufctl))); - - /* check if there is valid data in this urb */ - if (status) { - dbg ("complete with non-zero status: %d", status); - /* should we do a retry? */ - if (!auerswald_status_retry(status) - || !cp->usbdev - || (cp->version < AUV_RETRY) - || (bp->retries >= AU_RETRIES)) { - /* reuse the buffer */ - err ("control read: transmission error %d, can not retry", status); - auerbuf_releasebuf (bp); - /* Wake up all processes waiting for a buffer */ - wake_up (&cp->bufferwait); - return; - } - bp->retries++; - dbg ("Retry count = %d", bp->retries); - /* send a long dummy control-write-message to allow device firmware to react */ - bp->dr->bRequestType = AUT_WREQ; - bp->dr->bRequest = AUV_DUMMY; - bp->dr->wValue = bp->dr->wLength; /* temporary storage */ - // bp->dr->wIndex channel ID remains - bp->dr->wLength = cpu_to_le16 (32); /* >= 8 bytes */ - usb_fill_control_urb (bp->urbp, cp->usbdev, usb_sndctrlpipe (cp->usbdev, 0), - (unsigned char*)bp->dr, bp->bufp, 32, - auerswald_ctrlread_wretcomplete,bp); - - /* submit the control msg as next paket */ - ret = auerchain_submit_urb_list (&cp->controlchain, bp->urbp, 1); - if (ret) { - dbg ("auerswald_ctrlread_complete: nonzero result of auerchain_submit_urb_list %d", ret); - bp->urbp->status = ret; - auerswald_ctrlread_wretcomplete (bp->urbp); - } - return; - } - - /* get the actual bytecount (incl. headerbyte) */ - bp->len = urb->actual_length; - serviceid = bp->bufp[0] & AUH_TYPEMASK; - dbg ("Paket with serviceid %d and %d bytes received", serviceid, bp->len); - - /* dispatch the paket */ - scp = cp->services[serviceid]; - if (scp) { - /* look, Ma, a listener! */ - scp->dispatch (scp, bp); - } - - /* release the paket */ - auerbuf_releasebuf (bp); - /* Wake up all processes waiting for a buffer */ - wake_up (&cp->bufferwait); -} - -/*-------------------------------------------------------------------*/ -/* Handling of Interrupt Endpoint */ -/* This interrupt Endpoint is used to inform the host about waiting - messages from the USB device. -*/ -/* int completion handler. */ -static void auerswald_int_complete (struct urb * urb) -{ - unsigned long flags; - unsigned int channelid; - unsigned int bytecount; - int ret; - int status = urb->status; - pauerbuf_t bp = NULL; - pauerswald_t cp = urb->context; - - dbg ("%s called", __func__); - - switch (status) { - case 0: - /* success */ - break; - case -ECONNRESET: - case -ENOENT: - case -ESHUTDOWN: - /* this urb is terminated, clean up */ - dbg("%s - urb shutting down with status: %d", __func__, status); - return; - default: - dbg("%s - nonzero urb status received: %d", __func__, status); - goto exit; - } - - /* check if all needed data was received */ - if (urb->actual_length < AU_IRQMINSIZE) { - dbg ("invalid data length received: %d bytes", urb->actual_length); - goto exit; - } - - /* check the command code */ - if (cp->intbufp[0] != AU_IRQCMDID) { - dbg ("invalid command received: %d", cp->intbufp[0]); - goto exit; - } - - /* check the command type */ - if (cp->intbufp[1] != AU_BLOCKRDY) { - dbg ("invalid command type received: %d", cp->intbufp[1]); - goto exit; - } - - /* now extract the information */ - channelid = cp->intbufp[2]; - bytecount = (unsigned char)cp->intbufp[3]; - bytecount |= (unsigned char)cp->intbufp[4] << 8; - - /* check the channel id */ - if (channelid >= AUH_TYPESIZE) { - dbg ("invalid channel id received: %d", channelid); - goto exit; - } - - /* check the byte count */ - if (bytecount > (cp->maxControlLength+AUH_SIZE)) { - dbg ("invalid byte count received: %d", bytecount); - goto exit; - } - dbg ("Service Channel = %d", channelid); - dbg ("Byte Count = %d", bytecount); - - /* get a buffer for the next data paket */ - spin_lock_irqsave (&cp->bufctl.lock, flags); - if (!list_empty (&cp->bufctl.free_buff_list)) { - /* yes: get the entry */ - struct list_head *tmp = cp->bufctl.free_buff_list.next; - list_del (tmp); - bp = list_entry (tmp, auerbuf_t, buff_list); - } - spin_unlock_irqrestore (&cp->bufctl.lock, flags); - - /* if no buffer available: skip it */ - if (!bp) { - dbg ("auerswald_int_complete: no data buffer available"); - /* can we do something more? - This is a big problem: if this int packet is ignored, the - device will wait forever and not signal any more data. - The only real solution is: having enough buffers! - Or perhaps temporary disabling the int endpoint? - */ - goto exit; - } - - /* fill the control message */ - bp->dr->bRequestType = AUT_RREQ; - bp->dr->bRequest = AUV_RBLOCK; - bp->dr->wValue = cpu_to_le16 (0); - bp->dr->wIndex = cpu_to_le16 (channelid | AUH_DIRECT | AUH_UNSPLIT); - bp->dr->wLength = cpu_to_le16 (bytecount); - usb_fill_control_urb (bp->urbp, cp->usbdev, usb_rcvctrlpipe (cp->usbdev, 0), - (unsigned char*)bp->dr, bp->bufp, bytecount, - auerswald_ctrlread_complete,bp); - - /* submit the control msg */ - ret = auerchain_submit_urb (&cp->controlchain, bp->urbp); - if (ret) { - dbg ("auerswald_int_complete: nonzero result of auerchain_submit_urb %d", ret); - bp->urbp->status = ret; - auerswald_ctrlread_complete( bp->urbp); - /* here applies the same problem as above: device locking! */ - } -exit: - ret = usb_submit_urb (urb, GFP_ATOMIC); - if (ret) - err ("%s - usb_submit_urb failed with result %d", - __func__, ret); -} - -/* int memory deallocation - NOTE: no mutex please! -*/ -static void auerswald_int_free (pauerswald_t cp) -{ - if (cp->inturbp) { - usb_free_urb(cp->inturbp); - cp->inturbp = NULL; - } - kfree(cp->intbufp); - cp->intbufp = NULL; -} - -/* This function is called to activate the interrupt - endpoint. This function returns 0 if successful or an error code. - NOTE: no mutex please! -*/ -static int auerswald_int_open (pauerswald_t cp) -{ - int ret; - struct usb_host_endpoint *ep; - int irqsize; - dbg ("auerswald_int_open"); - - ep = cp->usbdev->ep_in[AU_IRQENDP]; - if (!ep) { - ret = -EFAULT; - goto intoend; - } - irqsize = le16_to_cpu(ep->desc.wMaxPacketSize); - cp->irqsize = irqsize; - - /* allocate the urb and data buffer */ - if (!cp->inturbp) { - cp->inturbp = usb_alloc_urb (0, GFP_KERNEL); - if (!cp->inturbp) { - ret = -ENOMEM; - goto intoend; - } - } - if (!cp->intbufp) { - cp->intbufp = kmalloc (irqsize, GFP_KERNEL); - if (!cp->intbufp) { - ret = -ENOMEM; - goto intoend; - } - } - /* setup urb */ - usb_fill_int_urb (cp->inturbp, cp->usbdev, - usb_rcvintpipe (cp->usbdev,AU_IRQENDP), cp->intbufp, - irqsize, auerswald_int_complete, cp, ep->desc.bInterval); - /* start the urb */ - cp->inturbp->status = 0; /* needed! */ - ret = usb_submit_urb (cp->inturbp, GFP_KERNEL); - -intoend: - if (ret < 0) { - /* activation of interrupt endpoint has failed. Now clean up. */ - dbg ("auerswald_int_open: activation of int endpoint failed"); - - /* deallocate memory */ - auerswald_int_free (cp); - } - return ret; -} - -/* This function is called to deactivate the interrupt - endpoint. This function returns 0 if successful or an error code. - NOTE: no mutex please! -*/ -static void auerswald_int_release (pauerswald_t cp) -{ - dbg ("auerswald_int_release"); - - /* stop the int endpoint */ - usb_kill_urb (cp->inturbp); - - /* deallocate memory */ - auerswald_int_free (cp); -} - -/* --------------------------------------------------------------------- */ -/* Helper functions */ - -/* wake up waiting readers */ -static void auerchar_disconnect (pauerscon_t scp) -{ - pauerchar_t ccp = ((pauerchar_t)((char *)(scp)-(unsigned long)(&((pauerchar_t)0)->scontext))); - dbg ("auerchar_disconnect called"); - ccp->removed = 1; - wake_up (&ccp->readwait); -} - - -/* dispatch a read paket to a waiting character device */ -static void auerchar_ctrlread_dispatch (pauerscon_t scp, pauerbuf_t bp) -{ - unsigned long flags; - pauerchar_t ccp; - pauerbuf_t newbp = NULL; - char * charp; - dbg ("auerchar_ctrlread_dispatch called"); - ccp = ((pauerchar_t)((char *)(scp)-(unsigned long)(&((pauerchar_t)0)->scontext))); - - /* get a read buffer from character device context */ - spin_lock_irqsave (&ccp->bufctl.lock, flags); - if (!list_empty (&ccp->bufctl.free_buff_list)) { - /* yes: get the entry */ - struct list_head *tmp = ccp->bufctl.free_buff_list.next; - list_del (tmp); - newbp = list_entry (tmp, auerbuf_t, buff_list); - } - spin_unlock_irqrestore (&ccp->bufctl.lock, flags); - - if (!newbp) { - dbg ("No read buffer available, discard paket!"); - return; /* no buffer, no dispatch */ - } - - /* copy information to new buffer element - (all buffers have the same length) */ - charp = newbp->bufp; - newbp->bufp = bp->bufp; - bp->bufp = charp; - newbp->len = bp->len; - - /* insert new buffer in read list */ - spin_lock_irqsave (&ccp->bufctl.lock, flags); - list_add_tail (&newbp->buff_list, &ccp->bufctl.rec_buff_list); - spin_unlock_irqrestore (&ccp->bufctl.lock, flags); - dbg ("read buffer appended to rec_list"); - - /* wake up pending synchronous reads */ - wake_up (&ccp->readwait); -} - - -/* Delete an auerswald driver context */ -static void auerswald_delete( pauerswald_t cp) -{ - dbg( "auerswald_delete"); - if (cp == NULL) - return; - - /* Wake up all processes waiting for a buffer */ - wake_up (&cp->bufferwait); - - /* Cleaning up */ - auerswald_int_release (cp); - auerchain_free (&cp->controlchain); - auerbuf_free_buffers (&cp->bufctl); - - /* release the memory */ - kfree( cp); -} - - -/* Delete an auerswald character context */ -static void auerchar_delete( pauerchar_t ccp) -{ - dbg ("auerchar_delete"); - if (ccp == NULL) - return; - - /* wake up pending synchronous reads */ - ccp->removed = 1; - wake_up (&ccp->readwait); - - /* remove the read buffer */ - if (ccp->readbuf) { - auerbuf_releasebuf (ccp->readbuf); - ccp->readbuf = NULL; - } - - /* remove the character buffers */ - auerbuf_free_buffers (&ccp->bufctl); - - /* release the memory */ - kfree( ccp); -} - - -/* add a new service to the device - scp->id must be set! - return: 0 if OK, else error code -*/ -static int auerswald_addservice (pauerswald_t cp, pauerscon_t scp) -{ - int ret; - - /* is the device available? */ - if (!cp->usbdev) { - dbg ("usbdev == NULL"); - return -EIO; /*no: can not add a service, sorry*/ - } - - /* is the service available? */ - if (cp->services[scp->id]) { - dbg ("service is busy"); - return -EBUSY; - } - - /* device is available, service is free */ - cp->services[scp->id] = scp; - - /* register service in device */ - ret = auerchain_control_msg( - &cp->controlchain, /* pointer to control chain */ - cp->usbdev, /* pointer to device */ - usb_sndctrlpipe (cp->usbdev, 0), /* pipe to control endpoint */ - AUV_CHANNELCTL, /* USB message request value */ - AUT_WREQ, /* USB message request type value */ - 0x01, /* open USB message value */ - scp->id, /* USB message index value */ - NULL, /* pointer to the data to send */ - 0, /* length in bytes of the data to send */ - HZ * 2); /* time to wait for the message to complete before timing out */ - if (ret < 0) { - dbg ("auerswald_addservice: auerchain_control_msg returned error code %d", ret); - /* undo above actions */ - cp->services[scp->id] = NULL; - return ret; - } - - dbg ("auerswald_addservice: channel open OK"); - return 0; -} - - -/* remove a service from the device - scp->id must be set! */ -static void auerswald_removeservice (pauerswald_t cp, pauerscon_t scp) -{ - dbg ("auerswald_removeservice called"); - - /* check if we have a service allocated */ - if (scp->id == AUH_UNASSIGNED) - return; - - /* If there is a device: close the channel */ - if (cp->usbdev) { - /* Close the service channel inside the device */ - int ret = auerchain_control_msg( - &cp->controlchain, /* pointer to control chain */ - cp->usbdev, /* pointer to device */ - usb_sndctrlpipe (cp->usbdev, 0), /* pipe to control endpoint */ - AUV_CHANNELCTL, /* USB message request value */ - AUT_WREQ, /* USB message request type value */ - 0x00, // close /* USB message value */ - scp->id, /* USB message index value */ - NULL, /* pointer to the data to send */ - 0, /* length in bytes of the data to send */ - HZ * 2); /* time to wait for the message to complete before timing out */ - if (ret < 0) { - dbg ("auerswald_removeservice: auerchain_control_msg returned error code %d", ret); - } - else { - dbg ("auerswald_removeservice: channel close OK"); - } - } - - /* remove the service from the device */ - cp->services[scp->id] = NULL; - scp->id = AUH_UNASSIGNED; -} - - -/* --------------------------------------------------------------------- */ -/* Char device functions */ - -/* Open a new character device */ -static int auerchar_open (struct inode *inode, struct file *file) -{ - int dtindex = iminor(inode); - pauerswald_t cp = NULL; - pauerchar_t ccp = NULL; - struct usb_interface *intf; - int ret; - - /* minor number in range? */ - if (dtindex < 0) { - return -ENODEV; - } - intf = usb_find_interface(&auerswald_driver, dtindex); - if (!intf) { - return -ENODEV; - } - - /* usb device available? */ - cp = usb_get_intfdata (intf); - if (cp == NULL) { - return -ENODEV; - } - if (mutex_lock_interruptible(&cp->mutex)) { - return -ERESTARTSYS; - } - - /* we have access to the device. Now lets allocate memory */ - ccp = kzalloc(sizeof(auerchar_t), GFP_KERNEL); - if (ccp == NULL) { - err ("out of memory"); - ret = -ENOMEM; - goto ofail; - } - - /* Initialize device descriptor */ - mutex_init(&ccp->mutex); - mutex_init(&ccp->readmutex); - auerbuf_init (&ccp->bufctl); - ccp->scontext.id = AUH_UNASSIGNED; - ccp->scontext.dispatch = auerchar_ctrlread_dispatch; - ccp->scontext.disconnect = auerchar_disconnect; - init_waitqueue_head (&ccp->readwait); - - ret = auerbuf_setup (&ccp->bufctl, AU_RBUFFERS, cp->maxControlLength+AUH_SIZE); - if (ret) { - goto ofail; - } - - cp->open_count++; - ccp->auerdev = cp; - dbg("open %s as /dev/%s", cp->dev_desc, cp->name); - mutex_unlock(&cp->mutex); - - /* file IO stuff */ - file->f_pos = 0; - file->private_data = ccp; - return nonseekable_open(inode, file); - - /* Error exit */ -ofail: mutex_unlock(&cp->mutex); - auerchar_delete (ccp); - return ret; -} - - -/* IOCTL functions */ -static long auerchar_ioctl(struct file *file, unsigned int cmd, - unsigned long arg) -{ - pauerchar_t ccp = (pauerchar_t) file->private_data; - int ret = 0; - audevinfo_t devinfo; - pauerswald_t cp = NULL; - unsigned int u; - unsigned int __user *user_arg = (unsigned int __user *)arg; - - dbg ("ioctl"); - - /* get the mutexes */ - if (mutex_lock_interruptible(&ccp->mutex)) { - return -ERESTARTSYS; - } - cp = ccp->auerdev; - if (!cp) { - mutex_unlock(&ccp->mutex); - return -ENODEV; - } - if (mutex_lock_interruptible(&cp->mutex)) { - mutex_unlock(&ccp->mutex); - return -ERESTARTSYS; - } - - /* Check for removal */ - if (!cp->usbdev) { - mutex_unlock(&cp->mutex); - mutex_unlock(&ccp->mutex); - return -ENODEV; - } - lock_kernel(); - switch (cmd) { - - /* return != 0 if Transmitt channel ready to send */ - case IOCTL_AU_TXREADY: - dbg ("IOCTL_AU_TXREADY"); - u = ccp->auerdev - && (ccp->scontext.id != AUH_UNASSIGNED) - && !list_empty (&cp->bufctl.free_buff_list); - ret = put_user (u, user_arg); - break; - - /* return != 0 if connected to a service channel */ - case IOCTL_AU_CONNECT: - dbg ("IOCTL_AU_CONNECT"); - u = (ccp->scontext.id != AUH_UNASSIGNED); - ret = put_user (u, user_arg); - break; - - /* return != 0 if Receive Data available */ - case IOCTL_AU_RXAVAIL: - dbg ("IOCTL_AU_RXAVAIL"); - if (ccp->scontext.id == AUH_UNASSIGNED) { - ret = -EIO; - break; - } - u = 0; /* no data */ - if (ccp->readbuf) { - int restlen = ccp->readbuf->len - ccp->readoffset; - if (restlen > 0) - u = 1; - } - if (!u) { - if (!list_empty (&ccp->bufctl.rec_buff_list)) { - u = 1; - } - } - ret = put_user (u, user_arg); - break; - - /* return the max. buffer length for the device */ - case IOCTL_AU_BUFLEN: - dbg ("IOCTL_AU_BUFLEN"); - u = cp->maxControlLength; - ret = put_user (u, user_arg); - break; - - /* requesting a service channel */ - case IOCTL_AU_SERVREQ: - dbg ("IOCTL_AU_SERVREQ"); - /* requesting a service means: release the previous one first */ - auerswald_removeservice (cp, &ccp->scontext); - /* get the channel number */ - ret = get_user (u, user_arg); - if (ret) { - break; - } - if ((u < AUH_FIRSTUSERCH) || (u >= AUH_TYPESIZE)) { - ret = -EIO; - break; - } - dbg ("auerchar service request parameters are ok"); - ccp->scontext.id = u; - - /* request the service now */ - ret = auerswald_addservice (cp, &ccp->scontext); - if (ret) { - /* no: revert service entry */ - ccp->scontext.id = AUH_UNASSIGNED; - } - break; - - /* get a string descriptor for the device */ - case IOCTL_AU_DEVINFO: - dbg ("IOCTL_AU_DEVINFO"); - if (copy_from_user (&devinfo, (void __user *) arg, sizeof (audevinfo_t))) { - ret = -EFAULT; - break; - } - u = strlen(cp->dev_desc)+1; - if (u > devinfo.bsize) { - u = devinfo.bsize; - } - ret = copy_to_user(devinfo.buf, cp->dev_desc, u) ? -EFAULT : 0; - break; - - /* get the max. string descriptor length */ - case IOCTL_AU_SLEN: - dbg ("IOCTL_AU_SLEN"); - u = AUSI_DLEN; - ret = put_user (u, user_arg); - break; - - default: - dbg ("IOCTL_AU_UNKNOWN"); - ret = -ENOTTY; - break; - } - unlock_kernel(); - /* release the mutexes */ - mutex_unlock(&cp->mutex); - mutex_unlock(&ccp->mutex); - return ret; -} - -/* Read data from the device */ -static ssize_t auerchar_read (struct file *file, char __user *buf, size_t count, loff_t * ppos) -{ - unsigned long flags; - pauerchar_t ccp = (pauerchar_t) file->private_data; - pauerbuf_t bp = NULL; - wait_queue_t wait; - - dbg ("auerchar_read"); - - /* Error checking */ - if (!ccp) - return -EIO; - if (*ppos) - return -ESPIPE; - if (count == 0) - return 0; - - /* get the mutex */ - if (mutex_lock_interruptible(&ccp->mutex)) - return -ERESTARTSYS; - - /* Can we expect to read something? */ - if (ccp->scontext.id == AUH_UNASSIGNED) { - mutex_unlock(&ccp->mutex); - return -EIO; - } - - /* only one reader per device allowed */ - if (mutex_lock_interruptible(&ccp->readmutex)) { - mutex_unlock(&ccp->mutex); - return -ERESTARTSYS; - } - - /* read data from readbuf, if available */ -doreadbuf: - bp = ccp->readbuf; - if (bp) { - /* read the maximum bytes */ - int restlen = bp->len - ccp->readoffset; - if (restlen < 0) - restlen = 0; - if (count > restlen) - count = restlen; - if (count) { - if (copy_to_user (buf, bp->bufp+ccp->readoffset, count)) { - dbg ("auerswald_read: copy_to_user failed"); - mutex_unlock(&ccp->readmutex); - mutex_unlock(&ccp->mutex); - return -EFAULT; - } - } - /* advance the read offset */ - ccp->readoffset += count; - restlen -= count; - // reuse the read buffer - if (restlen <= 0) { - auerbuf_releasebuf (bp); - ccp->readbuf = NULL; - } - /* return with number of bytes read */ - if (count) { - mutex_unlock(&ccp->readmutex); - mutex_unlock(&ccp->mutex); - return count; - } - } - - /* a read buffer is not available. Try to get the next data block. */ -doreadlist: - /* Preparing for sleep */ - init_waitqueue_entry (&wait, current); - set_current_state (TASK_INTERRUPTIBLE); - add_wait_queue (&ccp->readwait, &wait); - - bp = NULL; - spin_lock_irqsave (&ccp->bufctl.lock, flags); - if (!list_empty (&ccp->bufctl.rec_buff_list)) { - /* yes: get the entry */ - struct list_head *tmp = ccp->bufctl.rec_buff_list.next; - list_del (tmp); - bp = list_entry (tmp, auerbuf_t, buff_list); - } - spin_unlock_irqrestore (&ccp->bufctl.lock, flags); - - /* have we got data? */ - if (bp) { - ccp->readbuf = bp; - ccp->readoffset = AUH_SIZE; /* for headerbyte */ - set_current_state (TASK_RUNNING); - remove_wait_queue (&ccp->readwait, &wait); - goto doreadbuf; /* now we can read! */ - } - - /* no data available. Should we wait? */ - if (file->f_flags & O_NONBLOCK) { - dbg ("No read buffer available, returning -EAGAIN"); - set_current_state (TASK_RUNNING); - remove_wait_queue (&ccp->readwait, &wait); - mutex_unlock(&ccp->readmutex); - mutex_unlock(&ccp->mutex); - return -EAGAIN; /* nonblocking, no data available */ - } - - /* yes, we should wait! */ - mutex_unlock(&ccp->mutex); /* allow other operations while we wait */ - schedule(); - remove_wait_queue (&ccp->readwait, &wait); - if (signal_pending (current)) { - /* waked up by a signal */ - mutex_unlock(&ccp->readmutex); - return -ERESTARTSYS; - } - - /* Anything left to read? */ - if ((ccp->scontext.id == AUH_UNASSIGNED) || ccp->removed) { - mutex_unlock(&ccp->readmutex); - return -EIO; - } - - if (mutex_lock_interruptible(&ccp->mutex)) { - mutex_unlock(&ccp->readmutex); - return -ERESTARTSYS; - } - - /* try to read the incoming data again */ - goto doreadlist; -} - - -/* Write a data block into the right service channel of the device */ -static ssize_t auerchar_write (struct file *file, const char __user *buf, size_t len, loff_t *ppos) -{ - pauerchar_t ccp = (pauerchar_t) file->private_data; - pauerswald_t cp = NULL; - pauerbuf_t bp; - unsigned long flags; - int ret; - wait_queue_t wait; - - dbg ("auerchar_write %zd bytes", len); - - /* Error checking */ - if (!ccp) - return -EIO; - if (*ppos) - return -ESPIPE; - if (len == 0) - return 0; - -write_again: - /* get the mutex */ - if (mutex_lock_interruptible(&ccp->mutex)) - return -ERESTARTSYS; - - /* Can we expect to write something? */ - if (ccp->scontext.id == AUH_UNASSIGNED) { - mutex_unlock(&ccp->mutex); - return -EIO; - } - - cp = ccp->auerdev; - if (!cp) { - mutex_unlock(&ccp->mutex); - return -ERESTARTSYS; - } - if (mutex_lock_interruptible(&cp->mutex)) { - mutex_unlock(&ccp->mutex); - return -ERESTARTSYS; - } - if (!cp->usbdev) { - mutex_unlock(&cp->mutex); - mutex_unlock(&ccp->mutex); - return -EIO; - } - /* Prepare for sleep */ - init_waitqueue_entry (&wait, current); - set_current_state (TASK_INTERRUPTIBLE); - add_wait_queue (&cp->bufferwait, &wait); - - /* Try to get a buffer from the device pool. - We can't use a buffer from ccp->bufctl because the write - command will last beond a release() */ - bp = NULL; - spin_lock_irqsave (&cp->bufctl.lock, flags); - if (!list_empty (&cp->bufctl.free_buff_list)) { - /* yes: get the entry */ - struct list_head *tmp = cp->bufctl.free_buff_list.next; - list_del (tmp); - bp = list_entry (tmp, auerbuf_t, buff_list); - } - spin_unlock_irqrestore (&cp->bufctl.lock, flags); - - /* are there any buffers left? */ - if (!bp) { - mutex_unlock(&cp->mutex); - mutex_unlock(&ccp->mutex); - - /* NONBLOCK: don't wait */ - if (file->f_flags & O_NONBLOCK) { - set_current_state (TASK_RUNNING); - remove_wait_queue (&cp->bufferwait, &wait); - return -EAGAIN; - } - - /* BLOCKING: wait */ - schedule(); - remove_wait_queue (&cp->bufferwait, &wait); - if (signal_pending (current)) { - /* waked up by a signal */ - return -ERESTARTSYS; - } - goto write_again; - } else { - set_current_state (TASK_RUNNING); - remove_wait_queue (&cp->bufferwait, &wait); - } - - /* protect against too big write requests */ - if (len > cp->maxControlLength) - len = cp->maxControlLength; - - /* Fill the buffer */ - if (copy_from_user ( bp->bufp+AUH_SIZE, buf, len)) { - dbg ("copy_from_user failed"); - auerbuf_releasebuf (bp); - /* Wake up all processes waiting for a buffer */ - wake_up (&cp->bufferwait); - mutex_unlock(&cp->mutex); - mutex_unlock(&ccp->mutex); - return -EFAULT; - } - - /* set the header byte */ - *(bp->bufp) = ccp->scontext.id | AUH_DIRECT | AUH_UNSPLIT; - - /* Set the transfer Parameters */ - bp->len = len+AUH_SIZE; - bp->dr->bRequestType = AUT_WREQ; - bp->dr->bRequest = AUV_WBLOCK; - bp->dr->wValue = cpu_to_le16 (0); - bp->dr->wIndex = cpu_to_le16 (ccp->scontext.id | AUH_DIRECT | AUH_UNSPLIT); - bp->dr->wLength = cpu_to_le16 (len+AUH_SIZE); - usb_fill_control_urb (bp->urbp, cp->usbdev, usb_sndctrlpipe (cp->usbdev, 0), - (unsigned char*)bp->dr, bp->bufp, len+AUH_SIZE, - auerchar_ctrlwrite_complete, bp); - /* up we go */ - ret = auerchain_submit_urb (&cp->controlchain, bp->urbp); - mutex_unlock(&cp->mutex); - if (ret) { - dbg ("auerchar_write: nonzero result of auerchain_submit_urb %d", ret); - auerbuf_releasebuf (bp); - /* Wake up all processes waiting for a buffer */ - wake_up (&cp->bufferwait); - mutex_unlock(&ccp->mutex); - return -EIO; - } - else { - dbg ("auerchar_write: Write OK"); - mutex_unlock(&ccp->mutex); - return len; - } -} - - -/* Close a character device */ -static int auerchar_release (struct inode *inode, struct file *file) -{ - pauerchar_t ccp = (pauerchar_t) file->private_data; - pauerswald_t cp; - dbg("release"); - - mutex_lock(&ccp->mutex); - cp = ccp->auerdev; - if (cp) { - mutex_lock(&cp->mutex); - /* remove an open service */ - auerswald_removeservice (cp, &ccp->scontext); - /* detach from device */ - if ((--cp->open_count <= 0) && (cp->usbdev == NULL)) { - /* usb device waits for removal */ - mutex_unlock(&cp->mutex); - auerswald_delete (cp); - } else { - mutex_unlock(&cp->mutex); - } - cp = NULL; - ccp->auerdev = NULL; - } - mutex_unlock(&ccp->mutex); - auerchar_delete (ccp); - - return 0; -} - - -/*----------------------------------------------------------------------*/ -/* File operation structure */ -static const struct file_operations auerswald_fops = -{ - .owner = THIS_MODULE, - .llseek = no_llseek, - .read = auerchar_read, - .write = auerchar_write, - .unlocked_ioctl = auerchar_ioctl, - .open = auerchar_open, - .release = auerchar_release, -}; - -static struct usb_class_driver auerswald_class = { - .name = "auer%d", - .fops = &auerswald_fops, - .minor_base = AUER_MINOR_BASE, -}; - - -/* --------------------------------------------------------------------- */ -/* Special USB driver functions */ - -/* Probe if this driver wants to serve an USB device - - This entry point is called whenever a new device is attached to the bus. - Then the device driver has to create a new instance of its internal data - structures for the new device. - - The dev argument specifies the device context, which contains pointers - to all USB descriptors. The interface argument specifies the interface - number. If a USB driver wants to bind itself to a particular device and - interface it has to return a pointer. This pointer normally references - the device driver's context structure. - - Probing normally is done by checking the vendor and product identifications - or the class and subclass definitions. If they match the interface number - is compared with the ones supported by the driver. When probing is done - class based it might be necessary to parse some more USB descriptors because - the device properties can differ in a wide range. -*/ -static int auerswald_probe (struct usb_interface *intf, - const struct usb_device_id *id) -{ - struct usb_device *usbdev = interface_to_usbdev(intf); - pauerswald_t cp = NULL; - unsigned int u = 0; - __le16 *pbuf; - int ret; - - dbg ("probe: vendor id 0x%x, device id 0x%x", - le16_to_cpu(usbdev->descriptor.idVendor), - le16_to_cpu(usbdev->descriptor.idProduct)); - - /* we use only the first -and only- interface */ - if (intf->altsetting->desc.bInterfaceNumber != 0) - return -ENODEV; - - /* allocate memory for our device and initialize it */ - cp = kzalloc (sizeof(auerswald_t), GFP_KERNEL); - if (cp == NULL) { - err ("out of memory"); - goto pfail; - } - - /* Initialize device descriptor */ - mutex_init(&cp->mutex); - cp->usbdev = usbdev; - auerchain_init (&cp->controlchain); - auerbuf_init (&cp->bufctl); - init_waitqueue_head (&cp->bufferwait); - - ret = usb_register_dev(intf, &auerswald_class); - if (ret) { - err ("Not able to get a minor for this device."); - goto pfail; - } - - /* Give the device a name */ - sprintf (cp->name, "usb/auer%d", intf->minor); - - /* Store the index */ - cp->dtindex = intf->minor; - - /* Get the usb version of the device */ - cp->version = le16_to_cpu(cp->usbdev->descriptor.bcdDevice); - dbg ("Version is %X", cp->version); - - /* allow some time to settle the device */ - msleep(334); - - /* Try to get a suitable textual description of the device */ - /* Device name:*/ - ret = usb_string( cp->usbdev, AUSI_DEVICE, cp->dev_desc, AUSI_DLEN-1); - if (ret >= 0) { - u += ret; - /* Append Serial Number */ - memcpy(&cp->dev_desc[u], ",Ser# ", 6); - u += 6; - ret = usb_string( cp->usbdev, AUSI_SERIALNR, &cp->dev_desc[u], AUSI_DLEN-u-1); - if (ret >= 0) { - u += ret; - /* Append subscriber number */ - memcpy(&cp->dev_desc[u], ", ", 2); - u += 2; - ret = usb_string( cp->usbdev, AUSI_MSN, &cp->dev_desc[u], AUSI_DLEN-u-1); - if (ret >= 0) { - u += ret; - } - } - } - cp->dev_desc[u] = '\0'; - info("device is a %s", cp->dev_desc); - - /* get the maximum allowed control transfer length */ - pbuf = kmalloc(2, GFP_KERNEL); /* use an allocated buffer because of urb target */ - if (!pbuf) { - err( "out of memory"); - goto pfail; - } - ret = usb_control_msg(cp->usbdev, /* pointer to device */ - usb_rcvctrlpipe( cp->usbdev, 0 ), /* pipe to control endpoint */ - AUV_GETINFO, /* USB message request value */ - AUT_RREQ, /* USB message request type value */ - 0, /* USB message value */ - AUDI_MBCTRANS, /* USB message index value */ - pbuf, /* pointer to the receive buffer */ - 2, /* length of the buffer */ - 2000); /* time to wait for the message to complete before timing out */ - if (ret == 2) { - cp->maxControlLength = le16_to_cpup(pbuf); - kfree(pbuf); - dbg("setup: max. allowed control transfersize is %d bytes", cp->maxControlLength); - } else { - kfree(pbuf); - err("setup: getting max. allowed control transfer length failed with error %d", ret); - goto pfail; - } - - /* allocate a chain for the control messages */ - if (auerchain_setup (&cp->controlchain, AUCH_ELEMENTS)) { - err ("out of memory"); - goto pfail; - } - - /* allocate buffers for control messages */ - if (auerbuf_setup (&cp->bufctl, AU_RBUFFERS, cp->maxControlLength+AUH_SIZE)) { - err ("out of memory"); - goto pfail; - } - - /* start the interrupt endpoint */ - if (auerswald_int_open (cp)) { - err ("int endpoint failed"); - goto pfail; - } - - /* all OK */ - usb_set_intfdata (intf, cp); - return 0; - - /* Error exit: clean up the memory */ -pfail: auerswald_delete (cp); - return -EIO; -} - - -/* Disconnect driver from a served device - - This function is called whenever a device which was served by this driver - is disconnected. - - The argument dev specifies the device context and the driver_context - returns a pointer to the previously registered driver_context of the - probe function. After returning from the disconnect function the USB - framework completely deallocates all data structures associated with - this device. So especially the usb_device structure must not be used - any longer by the usb driver. -*/ -static void auerswald_disconnect (struct usb_interface *intf) -{ - pauerswald_t cp = usb_get_intfdata (intf); - unsigned int u; - - usb_set_intfdata (intf, NULL); - if (!cp) - return; - - /* give back our USB minor number */ - usb_deregister_dev(intf, &auerswald_class); - - mutex_lock(&cp->mutex); - info ("device /dev/%s now disconnecting", cp->name); - - /* Stop the interrupt endpoint */ - auerswald_int_release (cp); - - /* remove the control chain allocated in auerswald_probe - This has the benefit of - a) all pending (a)synchronous urbs are unlinked - b) all buffers dealing with urbs are reclaimed - */ - auerchain_free (&cp->controlchain); - - if (cp->open_count == 0) { - /* nobody is using this device. So we can clean up now */ - mutex_unlock(&cp->mutex); - /* mutex_unlock() is possible here because no other task - can open the device (see above). I don't want - to kfree() a locked mutex. */ - - auerswald_delete (cp); - } else { - /* device is used. Remove the pointer to the - usb device (it's not valid any more). The last - release() will do the clean up */ - cp->usbdev = NULL; - mutex_unlock(&cp->mutex); - /* Terminate waiting writers */ - wake_up (&cp->bufferwait); - /* Inform all waiting readers */ - for ( u = 0; u < AUH_TYPESIZE; u++) { - pauerscon_t scp = cp->services[u]; - if (scp) - scp->disconnect( scp); - } - } -} - -/* Descriptor for the devices which are served by this driver. - NOTE: this struct is parsed by the usbmanager install scripts. - Don't change without caution! -*/ -static struct usb_device_id auerswald_ids [] = { - { USB_DEVICE (ID_AUERSWALD, 0x00C0) }, /* COMpact 2104 USB */ - { USB_DEVICE (ID_AUERSWALD, 0x00DB) }, /* COMpact 4410/2206 USB */ - { USB_DEVICE (ID_AUERSWALD, 0x00DC) }, /* COMpact 4406 DSL */ - { USB_DEVICE (ID_AUERSWALD, 0x00DD) }, /* COMpact 2204 USB */ - { USB_DEVICE (ID_AUERSWALD, 0x00F1) }, /* Comfort 2000 System Telephone */ - { USB_DEVICE (ID_AUERSWALD, 0x00F2) }, /* Comfort 1200 System Telephone */ - { } /* Terminating entry */ -}; - -/* Standard module device table */ -MODULE_DEVICE_TABLE (usb, auerswald_ids); - -/* Standard usb driver struct */ -static struct usb_driver auerswald_driver = { - .name = "auerswald", - .probe = auerswald_probe, - .disconnect = auerswald_disconnect, - .id_table = auerswald_ids, -}; - - -/* --------------------------------------------------------------------- */ -/* Module loading/unloading */ - -/* Driver initialisation. Called after module loading. - NOTE: there is no concurrency at _init -*/ -static int __init auerswald_init (void) -{ - int result; - dbg ("init"); - - /* register driver at the USB subsystem */ - result = usb_register (&auerswald_driver); - if (result < 0) { - err ("driver could not be registered"); - return -1; - } - return 0; -} - -/* Driver deinit. Called before module removal. - NOTE: there is no concurrency at _cleanup -*/ -static void __exit auerswald_cleanup (void) -{ - dbg ("cleanup"); - usb_deregister (&auerswald_driver); -} - -/* --------------------------------------------------------------------- */ -/* Linux device driver module description */ - -MODULE_AUTHOR (DRIVER_AUTHOR); -MODULE_DESCRIPTION (DRIVER_DESC); -MODULE_LICENSE ("GPL"); - -module_init (auerswald_init); -module_exit (auerswald_cleanup); - -/* --------------------------------------------------------------------- */ - -- GitLab From c728df70ab0dd59b8ccdc3c611ea88925e6697db Mon Sep 17 00:00:00 2001 From: David Brownell Date: Sat, 26 Jul 2008 08:06:24 -0700 Subject: [PATCH 273/750] USB: fix USB boot crash, ecm_do_notify(), list_add corruption. prev->next should be next (ffff88003b8f82f8) This fixes a BUG() turned up by Ingo via randconfig testing, where CONFIG_LIST_DEBUG turned up list corruption. The corruption was caused by the dummy_hcd (single-machine test harness for gadget and HCD code) trashing the request queue when driven by the new CDC composite gadget an I/O pattern that was previously uncommon. Fix suggested by Alan Stern. Signed-off-by: David Brownell Tested-by: Ingo Molnar Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/dummy_hcd.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/usb/gadget/dummy_hcd.c b/drivers/usb/gadget/dummy_hcd.c index 21d1406af9e..7600a0c7875 100644 --- a/drivers/usb/gadget/dummy_hcd.c +++ b/drivers/usb/gadget/dummy_hcd.c @@ -542,13 +542,14 @@ dummy_queue (struct usb_ep *_ep, struct usb_request *_req, req->req.context = dum; req->req.complete = fifo_complete; + list_add_tail(&req->queue, &ep->queue); spin_unlock (&dum->lock); _req->actual = _req->length; _req->status = 0; _req->complete (_ep, _req); spin_lock (&dum->lock); - } - list_add_tail (&req->queue, &ep->queue); + } else + list_add_tail(&req->queue, &ep->queue); spin_unlock_irqrestore (&dum->lock, flags); /* real hardware would likely enable transfers here, in case -- GitLab From b5894a500127fce1db1309db5f9ca8b77a2ac266 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Andr=C3=A9=20Schenk?= Date: Mon, 28 Jul 2008 15:48:46 +0200 Subject: [PATCH 274/750] USB: ftdi_sio: Add USB Product Id for ELV HS485 USB product id registration for the ELV HS485 USB adapter (www.elv.de) to their home automation bus system. Applies to 2.6.26. Signed-off-by: Andre Schenk Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 1 + drivers/usb/serial/ftdi_sio.h | 1 + 2 files changed, 2 insertions(+) diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 83871725014..974e0eb5e75 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -563,6 +563,7 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_ELV_FHZ1300PC_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_EM1010PC_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELV_WS500_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_ELV_HS485_PID) }, { USB_DEVICE(FTDI_VID, LINX_SDMUSBQSS_PID) }, { USB_DEVICE(FTDI_VID, LINX_MASTERDEVEL2_PID) }, { USB_DEVICE(FTDI_VID, LINX_FUTURE_0_PID) }, diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h index a577ea44dcf..68927107cd9 100644 --- a/drivers/usb/serial/ftdi_sio.h +++ b/drivers/usb/serial/ftdi_sio.h @@ -524,6 +524,7 @@ #define FTDI_ELV_WS300PC_PID 0xE0F6 /* PC-Wetterstation (WS 300 PC) */ #define FTDI_ELV_FHZ1300PC_PID 0xE0E8 /* FHZ 1300 PC */ #define FTDI_ELV_WS500_PID 0xE0E9 /* PC-Wetterstation (WS 500) */ +#define FTDI_ELV_HS485_PID 0xE0EA /* USB to RS-485 adapter */ #define FTDI_ELV_EM1010PC_PID 0xE0EF /* Engery monitor EM 1010 PC */ /* -- GitLab From a00c3cadc2bf50b3c925acdb3d0e5789b1650498 Mon Sep 17 00:00:00 2001 From: Frederik Kriewitz Date: Wed, 30 Jul 2008 16:53:41 +0200 Subject: [PATCH 275/750] USB: ftdi_sio: add support for Luminance Stellaris Evaluation/Development Kits The Patch adds support for Luminance Stellaris Evaluation/Development Kits (FTDI 2232C based). The PIDs were missing. Successfully tested with a Stellaris LM3S8962 Evaluation kit. Signed-off-by: Frederik Kriewitz Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 4 ++++ drivers/usb/serial/ftdi_sio.h | 5 +++++ 2 files changed, 9 insertions(+) diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 974e0eb5e75..54407351d7e 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -647,6 +647,10 @@ static struct usb_device_id id_table_combined [] = { .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(FTDI_VID, FTDI_OOCDLINK_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, + { USB_DEVICE(FTDI_VID, LMI_LM3S_DEVEL_BOARD_PID), + .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, + { USB_DEVICE(FTDI_VID, LMI_LM3S_EVAL_BOARD_PID), + .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(RATOC_VENDOR_ID, RATOC_PRODUCT_ID_USB60F) }, { USB_DEVICE(FTDI_VID, FTDI_REU_TINY_PID) }, { }, /* Optional parameter entry */ diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h index 68927107cd9..7ca2ad0157f 100644 --- a/drivers/usb/serial/ftdi_sio.h +++ b/drivers/usb/serial/ftdi_sio.h @@ -816,6 +816,11 @@ #define OLIMEX_VID 0x15BA #define OLIMEX_ARM_USB_OCD_PID 0x0003 +/* Luminary Micro Stellaris Boards, VID = FTDI_VID */ +/* FTDI 2332C Dual channel device, side A=245 FIFO (JTAG), Side B=RS232 UART */ +#define LMI_LM3S_DEVEL_BOARD_PID 0xbcd8 +#define LMI_LM3S_EVAL_BOARD_PID 0xbcd9 + /* www.elsterelectricity.com Elster Unicom III Optical Probe */ #define FTDI_ELSTER_UNICOM_PID 0xE700 /* Product Id */ -- GitLab From f4f4d58734916e816d4b4a7cf61b3fc22ce02683 Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Mon, 28 Jul 2008 10:39:28 -0400 Subject: [PATCH 276/750] USB: add missing kerneldoc line for "needs_binding" This patch (as1117) adds a kerneldoc line for the "needs_binding" field in struct usb_interface. It was accidentally omitted when the field was added. Signed-off-by: Alan Stern Signed-off-by: Greg Kroah-Hartman --- include/linux/usb.h | 2 ++ 1 file changed, 2 insertions(+) diff --git a/include/linux/usb.h b/include/linux/usb.h index 5811c5da69f..0924cd9c30f 100644 --- a/include/linux/usb.h +++ b/include/linux/usb.h @@ -110,6 +110,8 @@ enum usb_interface_condition { * @sysfs_files_created: sysfs attributes exist * @needs_remote_wakeup: flag set when the driver requires remote-wakeup * capability during autosuspend. + * @needs_binding: flag set when the driver should be re-probed or unbound + * following a reset or suspend operation it doesn't support. * @dev: driver model's view of this device * @usb_dev: if an interface is bound to the USB major, this will point * to the sysfs representation for that device. -- GitLab From fa41019c7aa172fde075849834409d23eb49f582 Mon Sep 17 00:00:00 2001 From: Alexander Beregalov Date: Tue, 29 Jul 2008 05:54:31 +0400 Subject: [PATCH 277/750] usb/core/driver: fix warning usb/core/driver: fix warning: drivers/usb/core/driver.c:834: warning: 'do_unbind_rebind' defined but not used Signed-off-by: Alexander Beregalov Acked-by: Alan Stern Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/driver.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c index ddb54e14a5c..6618bc89eb6 100644 --- a/drivers/usb/core/driver.c +++ b/drivers/usb/core/driver.c @@ -774,6 +774,7 @@ void usb_deregister(struct usb_driver *driver) } EXPORT_SYMBOL_GPL(usb_deregister); +#ifdef CONFIG_PM /* Forced unbinding of a USB interface driver, either because * it doesn't support pre_reset/post_reset/reset_resume or @@ -872,8 +873,6 @@ static void do_unbind_rebind(struct usb_device *udev, int action) } } -#ifdef CONFIG_PM - /* Caller has locked udev's pm_mutex */ static int usb_suspend_device(struct usb_device *udev, pm_message_t msg) { -- GitLab From 38b375d9610e2467cb793a84d17c6f65e44cdb39 Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Mon, 21 Jul 2008 09:56:26 -0400 Subject: [PATCH 278/750] USB: OHCI: fix system hang caused by earlier patch This patch (as1114) fixes a problem that was revealed by an earlier patch (as1069b). Some broken controllers seem never to turn off their RHCS interrupt status bit, even when told to do so. As a result they generate an interrupt storm and hang the system. The patch avoids enabling RHSC interrupt requests when the RHCS status bit is already set. This should have no adverse affects on normal controllers, since they won't set the status bit until a root-hub status change actually occurs, in which case we wouldn't enable RHSC interrupt requests anyway -- we would wait until the status change had been processed and cleared. Signed-off-by: Alan Stern Tested by: Andrey Borzenkov Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ohci-hub.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/usb/host/ohci-hub.c b/drivers/usb/host/ohci-hub.c index b56739221d1..d54183f1d70 100644 --- a/drivers/usb/host/ohci-hub.c +++ b/drivers/usb/host/ohci-hub.c @@ -483,6 +483,13 @@ ohci_hub_status_data (struct usb_hcd *hcd, char *buf) length++; } + /* Some broken controllers never turn off RHCS in the interrupt + * status register. For their sake we won't re-enable RHSC + * interrupts if the flag is already set. + */ + if (ohci_readl(ohci, &ohci->regs->intrstatus) & OHCI_INTR_RHSC) + changed = 1; + /* look at each port */ for (i = 0; i < ohci->num_ports; i++) { u32 status = roothub_portstatus (ohci, i); -- GitLab From b9a097f26e55968cbc52e30a4a2e73d32d7604ce Mon Sep 17 00:00:00 2001 From: Dave Jones Date: Mon, 14 Jul 2008 13:28:34 -0400 Subject: [PATCH 279/750] USB: usb-storage: quirk around v1.11 firmware on Nikon D4 usb-storage: quirk around v1.11 firmware on Nikon D40 https://bugzilla.redhat.com/show_bug.cgi?id=454028 Just as in earlier firmware versions, we need to perform this quirk for the latest version too. Speculatively do the entry for the D80 too, as they seem to have the same firmware problems historically. Signed-off-by: Dave Jones Cc: Johannes Berg Cc: Alan Stern Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/unusual_devs.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h index 7ae69f55aa9..35ec1c69be1 100644 --- a/drivers/usb/storage/unusual_devs.h +++ b/drivers/usb/storage/unusual_devs.h @@ -356,14 +356,14 @@ UNUSUAL_DEV( 0x04b0, 0x040f, 0x0100, 0x0200, US_FL_FIX_CAPACITY), /* Reported by Emil Larsson */ -UNUSUAL_DEV( 0x04b0, 0x0411, 0x0100, 0x0110, +UNUSUAL_DEV( 0x04b0, 0x0411, 0x0100, 0x0111, "NIKON", "NIKON DSC D80", US_SC_DEVICE, US_PR_DEVICE, NULL, US_FL_FIX_CAPACITY), /* Reported by Ortwin Glueck */ -UNUSUAL_DEV( 0x04b0, 0x0413, 0x0110, 0x0110, +UNUSUAL_DEV( 0x04b0, 0x0413, 0x0110, 0x0111, "NIKON", "NIKON DSC D40", US_SC_DEVICE, US_PR_DEVICE, NULL, -- GitLab From e67d70f2f55d90c79dcb384ad5b798f0f9a68085 Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Thu, 17 Jul 2008 17:26:49 +0300 Subject: [PATCH 280/750] usb: gadget: protect gadget_chips.h from been included twice Without it, we might have trouble when trying to write some composite gadget drivers. Cc: David Brownell Cc: Greg KH Signed-off-by: Felipe Balbi Acked-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/gadget_chips.h | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/usb/gadget/gadget_chips.h b/drivers/usb/gadget/gadget_chips.h index 5246e8fef2b..17d9905101b 100644 --- a/drivers/usb/gadget/gadget_chips.h +++ b/drivers/usb/gadget/gadget_chips.h @@ -11,6 +11,10 @@ * Some are available on 2.4 kernels; several are available, but not * yet pushed in the 2.6 mainline tree. */ + +#ifndef __GADGET_CHIPS_H +#define __GADGET_CHIPS_H + #ifdef CONFIG_USB_GADGET_NET2280 #define gadget_is_net2280(g) !strcmp("net2280", (g)->name) #else @@ -237,3 +241,5 @@ static inline bool gadget_supports_altsettings(struct usb_gadget *gadget) /* Everything else is *presumably* fine ... */ return true; } + +#endif /* __GADGET_CHIPS_H */ -- GitLab From 0282b7f2a874e72c18fcd5a112ccf67f71ba7f5c Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Tue, 29 Jul 2008 12:01:04 -0400 Subject: [PATCH 281/750] usb-serial: don't release unregistered minors This patch (as1121) fixes a bug in the USB serial core. When a device is unregistered, the core will give back its minors -- even if the device hasn't been assigned any! The patch reserves the highest minor value (255) to mean that no minor was assigned. It also removes some dead code and does a small style fixup. Signed-off-by: Alan Stern Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/usb-serial.c | 7 +++---- include/linux/usb/serial.h | 3 ++- 2 files changed, 5 insertions(+), 5 deletions(-) diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c index 8c2d531eede..b157c48e8b7 100644 --- a/drivers/usb/serial/usb-serial.c +++ b/drivers/usb/serial/usb-serial.c @@ -122,9 +122,6 @@ static void return_serial(struct usb_serial *serial) dbg("%s", __func__); - if (serial == NULL) - return; - for (i = 0; i < serial->num_ports; ++i) serial_table[serial->minor + i] = NULL; } @@ -142,7 +139,8 @@ static void destroy_serial(struct kref *kref) serial->type->shutdown(serial); /* return the minor range that this device had */ - return_serial(serial); + if (serial->minor != SERIAL_TTY_NO_MINOR) + return_serial(serial); for (i = 0; i < serial->num_ports; ++i) serial->port[i]->port.count = 0; @@ -575,6 +573,7 @@ static struct usb_serial *create_serial(struct usb_device *dev, serial->interface = interface; kref_init(&serial->kref); mutex_init(&serial->disc_mutex); + serial->minor = SERIAL_TTY_NO_MINOR; return serial; } diff --git a/include/linux/usb/serial.h b/include/linux/usb/serial.h index 09a3e6a7518..655341d0f53 100644 --- a/include/linux/usb/serial.h +++ b/include/linux/usb/serial.h @@ -17,7 +17,8 @@ #include #define SERIAL_TTY_MAJOR 188 /* Nice legal number now */ -#define SERIAL_TTY_MINORS 255 /* loads of devices :) */ +#define SERIAL_TTY_MINORS 254 /* loads of devices :) */ +#define SERIAL_TTY_NO_MINOR 255 /* No minor was assigned */ /* The maximum number of ports one device can grab at once */ #define MAX_NUM_PORTS 8 -- GitLab From 1a21175a615ed346e8043f5e9d60a672266b84b4 Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Wed, 30 Jul 2008 11:31:50 -0400 Subject: [PATCH 282/750] USB: fix interface unregistration logic This patch (as1122) fixes a bug: When an interface is unregistered, its children (sysfs files and endpoint devices) are unregistered after it instead of before. Signed-off-by: Alan Stern Tested-by: Kay Sievers Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/message.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c index 586d6f1376c..286b4431a09 100644 --- a/drivers/usb/core/message.c +++ b/drivers/usb/core/message.c @@ -1091,8 +1091,8 @@ void usb_disable_device(struct usb_device *dev, int skip_ep0) continue; dev_dbg(&dev->dev, "unregistering interface %s\n", dev_name(&interface->dev)); - device_del(&interface->dev); usb_remove_sysfs_intf_files(interface); + device_del(&interface->dev); } /* Now that the interfaces are unbound, nobody should -- GitLab From 59f4ff2ecff4cef36378928cec891785b402e80c Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Tue, 29 Jul 2008 11:58:06 -0400 Subject: [PATCH 283/750] usb-storage: automatically recognize bad residues This patch (as1119) will help to reduce the clutter of usb-storage's unusual_devs file by automatically detecting some devices that need the IGNORE_RESIDUE flag. The idea is that devices should never return a non-zero residue for an INQUIRY or a READ CAPACITY command unless they failed to transfer all the requested data. So if one of these commands transfers a standard amount of data but there is a positive residue, we know that the residue is bogus and we can set the flag. This fixes the problems reported in Bugzilla #11125. Signed-off-by: Alan Stern Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/transport.c | 17 +++++++++++++++-- 1 file changed, 15 insertions(+), 2 deletions(-) diff --git a/drivers/usb/storage/transport.c b/drivers/usb/storage/transport.c index fcbbfdb7b2b..3523a0bfa0f 100644 --- a/drivers/usb/storage/transport.c +++ b/drivers/usb/storage/transport.c @@ -1032,8 +1032,21 @@ int usb_stor_Bulk_transport(struct scsi_cmnd *srb, struct us_data *us) /* try to compute the actual residue, based on how much data * was really transferred and what the device tells us */ - if (residue) { - if (!(us->fflags & US_FL_IGNORE_RESIDUE)) { + if (residue && !(us->fflags & US_FL_IGNORE_RESIDUE)) { + + /* Heuristically detect devices that generate bogus residues + * by seeing what happens with INQUIRY and READ CAPACITY + * commands. + */ + if (bcs->Status == US_BULK_STAT_OK && + scsi_get_resid(srb) == 0 && + ((srb->cmnd[0] == INQUIRY && + transfer_length == 36) || + (srb->cmnd[0] == READ_CAPACITY && + transfer_length == 8))) { + us->fflags |= US_FL_IGNORE_RESIDUE; + + } else { residue = min(residue, transfer_length); scsi_set_resid(srb, max(scsi_get_resid(srb), (int) residue)); -- GitLab From 3bea302d6aa61f2371a63e9ad81eaa373fd66441 Mon Sep 17 00:00:00 2001 From: Simon Arlott Date: Mon, 21 Jul 2008 20:44:50 +0100 Subject: [PATCH 284/750] USB: Move usb/mon/ up to misc options in Kconfig This makes "USB Monitor" appear under "Miscellaneous USB options" section instead of in the middle of device specific drivers in the "USB Imaging devices" section. Signed-off-by: Simon Arlott Signed-off-by: Greg Kroah-Hartman --- drivers/usb/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig index 755823cdf62..4f9b5ecfb72 100644 --- a/drivers/usb/Kconfig +++ b/drivers/usb/Kconfig @@ -95,6 +95,8 @@ config USB source "drivers/usb/core/Kconfig" +source "drivers/usb/mon/Kconfig" + source "drivers/usb/host/Kconfig" source "drivers/usb/class/Kconfig" @@ -103,8 +105,6 @@ source "drivers/usb/storage/Kconfig" source "drivers/usb/image/Kconfig" -source "drivers/usb/mon/Kconfig" - comment "USB port drivers" depends on USB -- GitLab From 368ee6469c327364ea10082a348f91c1f5ba47f7 Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Mon, 21 Jul 2008 10:08:28 -0400 Subject: [PATCH 285/750] usb-storage: unusual_devs entries for iRiver T10 and Datafab CF+SM reader This patch (as1115) adds unusual_devs entries with the IGNORE_RESIDE flag for the iRiver T10 and the Simple Tech/Datafab CF+SM card reader. Apparently these devices provide reasonable residue values for READ and WRITE operations, but not for others like INQUIRY or READ CAPACITY. This fixes the iRiver T10 problem reported in Bugzilla #11125. Signed-off-by: Alan Stern Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/unusual_devs.h | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h index 35ec1c69be1..11249bf5d74 100644 --- a/drivers/usb/storage/unusual_devs.h +++ b/drivers/usb/storage/unusual_devs.h @@ -1185,6 +1185,13 @@ UNUSUAL_DEV( 0x07c4, 0xa400, 0x0000, 0xffff, US_SC_DEVICE, US_PR_DEVICE, NULL, US_FL_FIX_INQUIRY ), +/* Reported by Rauch Wolke */ +UNUSUAL_DEV( 0x07c4, 0xa4a5, 0x0000, 0xffff, + "Simple Tech/Datafab", + "CF+SM Reader", + US_SC_DEVICE, US_PR_DEVICE, NULL, + US_FL_IGNORE_RESIDUE ), + /* Casio QV 2x00/3x00/4000/8000 digital still cameras are not conformant * to the USB storage specification in two ways: * - They tell us they are using transport protocol CBI. In reality they @@ -1767,6 +1774,13 @@ UNUSUAL_DEV( 0x2770, 0x915d, 0x0010, 0x0010, US_SC_DEVICE, US_PR_DEVICE, NULL, US_FL_FIX_CAPACITY ), +/* Reported by Andrey Rahmatullin */ +UNUSUAL_DEV( 0x4102, 0x1020, 0x0100, 0x0100, + "iRiver", + "MP3 T10", + US_SC_DEVICE, US_PR_DEVICE, NULL, + US_FL_IGNORE_RESIDUE ), + /* * David Härdeman * The key makes the SCSI stack print confusing (but harmless) messages -- GitLab From 8c809681ba0289afd0ed7bbb63679a0568dd441d Mon Sep 17 00:00:00 2001 From: Tollef Fog Heen Date: Tue, 22 Jul 2008 09:28:05 +0200 Subject: [PATCH 286/750] USB: pl2023: Remove USB id (4348:5523) handled by ch341 USB ID 4348:5523 is handled by the ch341 driver. Remove it from the pl2023 driver. Reverts 002e8f2c80c6be76bb312940bc278fc10b2b2487. Signed-off-by: Tollef Fog Heen Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/pl2303.c | 1 - drivers/usb/serial/pl2303.h | 4 ---- 2 files changed, 5 deletions(-) diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c index 2c9c446ad62..1ede1441cb1 100644 --- a/drivers/usb/serial/pl2303.c +++ b/drivers/usb/serial/pl2303.c @@ -90,7 +90,6 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(ALCOR_VENDOR_ID, ALCOR_PRODUCT_ID) }, { USB_DEVICE(WS002IN_VENDOR_ID, WS002IN_PRODUCT_ID) }, { USB_DEVICE(COREGA_VENDOR_ID, COREGA_PRODUCT_ID) }, - { USB_DEVICE(HL340_VENDOR_ID, HL340_PRODUCT_ID) }, { USB_DEVICE(YCCABLE_VENDOR_ID, YCCABLE_PRODUCT_ID) }, { } /* Terminating entry */ }; diff --git a/drivers/usb/serial/pl2303.h b/drivers/usb/serial/pl2303.h index 6ac3bbcf7a2..a3bd039c78e 100644 --- a/drivers/usb/serial/pl2303.h +++ b/drivers/usb/serial/pl2303.h @@ -107,10 +107,6 @@ #define COREGA_VENDOR_ID 0x07aa #define COREGA_PRODUCT_ID 0x002a -/* HL HL-340 (ID: 4348:5523) */ -#define HL340_VENDOR_ID 0x4348 -#define HL340_PRODUCT_ID 0x5523 - /* Y.C. Cable U.S.A., Inc - USB to RS-232 */ #define YCCABLE_VENDOR_ID 0x05ad #define YCCABLE_PRODUCT_ID 0x0fba -- GitLab From 4e0fee82619937acb13806ffc901d3920b947286 Mon Sep 17 00:00:00 2001 From: Kevin Lloyd Date: Thu, 10 Jul 2008 14:14:47 -0700 Subject: [PATCH 287/750] USB Serial Sierra: clean-up Very minor changes to clean up sierra code. Adds a prefix to debug messages so that Sierra messages are easily recognized. Removes extraneous code. This targets kernel 2.6.26-rc9 Signed-off-by: Kevin Lloyd Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/sierra.c | 56 ++++++++++++++++++------------------- 1 file changed, 27 insertions(+), 29 deletions(-) diff --git a/drivers/usb/serial/sierra.c b/drivers/usb/serial/sierra.c index 2f6f1523ec5..a3aaf08e56d 100644 --- a/drivers/usb/serial/sierra.c +++ b/drivers/usb/serial/sierra.c @@ -51,7 +51,7 @@ enum devicetype { static int sierra_set_power_state(struct usb_device *udev, __u16 swiState) { int result; - dev_dbg(&udev->dev, "%s", "SET POWER STATE\n"); + dev_dbg(&udev->dev, "%s", __func__); result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), SWIMS_USB_REQUEST_SetPower, /* __u8 request */ USB_TYPE_VENDOR, /* __u8 request type */ @@ -66,7 +66,7 @@ static int sierra_set_power_state(struct usb_device *udev, __u16 swiState) static int sierra_set_ms_mode(struct usb_device *udev, __u16 eSWocMode) { int result; - dev_dbg(&udev->dev, "%s", "DEVICE MODE SWITCH\n"); + dev_dbg(&udev->dev, "%s", __func__); result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), SWIMS_USB_REQUEST_SetMode, /* __u8 request */ USB_TYPE_VENDOR, /* __u8 request type */ @@ -81,7 +81,7 @@ static int sierra_set_ms_mode(struct usb_device *udev, __u16 eSWocMode) static int sierra_vsc_set_nmea(struct usb_device *udev, __u16 enable) { int result; - dev_dbg(&udev->dev, "%s", "NMEA Enable sent\n"); + dev_dbg(&udev->dev, "%s", __func__); result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), SWIMS_USB_REQUEST_SetNmea, /* __u8 request */ USB_TYPE_VENDOR, /* __u8 request type */ @@ -97,6 +97,7 @@ static int sierra_calc_num_ports(struct usb_serial *serial) { int result; int *num_ports = usb_get_serial_data(serial); + dev_dbg(&serial->dev->dev, "%s", __func__); result = *num_ports; @@ -110,22 +111,23 @@ static int sierra_calc_num_ports(struct usb_serial *serial) static int sierra_calc_interface(struct usb_serial *serial) { - int interface; - struct usb_interface *p_interface; - struct usb_host_interface *p_host_interface; + int interface; + struct usb_interface *p_interface; + struct usb_host_interface *p_host_interface; + dev_dbg(&serial->dev->dev, "%s", __func__); - /* Get the interface structure pointer from the serial struct */ - p_interface = serial->interface; + /* Get the interface structure pointer from the serial struct */ + p_interface = serial->interface; - /* Get a pointer to the host interface structure */ - p_host_interface = p_interface->cur_altsetting; + /* Get a pointer to the host interface structure */ + p_host_interface = p_interface->cur_altsetting; - /* read the interface descriptor for this active altsetting - * to find out the interface number we are on - */ - interface = p_host_interface->desc.bInterfaceNumber; + /* read the interface descriptor for this active altsetting + * to find out the interface number we are on + */ + interface = p_host_interface->desc.bInterfaceNumber; - return interface; + return interface; } static int sierra_probe(struct usb_serial *serial, @@ -135,6 +137,7 @@ static int sierra_probe(struct usb_serial *serial, struct usb_device *udev; int *num_ports; u8 ifnum; + dev_dbg(&serial->dev->dev, "%s", __func__); num_ports = kmalloc(sizeof(*num_ports), GFP_KERNEL); if (!num_ports) @@ -187,24 +190,26 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(0x1199, 0x0218) }, /* Sierra Wireless MC5720 */ { USB_DEVICE(0x0f30, 0x1b1d) }, /* Sierra Wireless MC5720 */ { USB_DEVICE(0x1199, 0x0020) }, /* Sierra Wireless MC5725 */ + { USB_DEVICE(0x1199, 0x0024) }, /* Sierra Wireless MC5727 */ { USB_DEVICE(0x1199, 0x0220) }, /* Sierra Wireless MC5725 */ { USB_DEVICE(0x1199, 0x0019) }, /* Sierra Wireless AirCard 595 */ { USB_DEVICE(0x1199, 0x0021) }, /* Sierra Wireless AirCard 597E */ { USB_DEVICE(0x1199, 0x0120) }, /* Sierra Wireless USB Dongle 595U */ - { USB_DEVICE_AND_INTERFACE_INFO(0x1199, 0x0023, 0xFF, 0xFF, 0xFF) }, /* Sierra Wireless C597 */ + /* Sierra Wireless C597 */ + { USB_DEVICE_AND_INTERFACE_INFO(0x1199, 0x0023, 0xFF, 0xFF, 0xFF) }, { USB_DEVICE(0x1199, 0x6802) }, /* Sierra Wireless MC8755 */ { USB_DEVICE(0x1199, 0x6804) }, /* Sierra Wireless MC8755 */ { USB_DEVICE(0x1199, 0x6803) }, /* Sierra Wireless MC8765 */ { USB_DEVICE(0x1199, 0x6812) }, /* Sierra Wireless MC8775 & AC 875U */ - { USB_DEVICE(0x1199, 0x6813) }, /* Sierra Wireless MC8775 (Thinkpad internal) */ + { USB_DEVICE(0x1199, 0x6813) }, /* Sierra Wireless MC8775 (Lenovo) */ { USB_DEVICE(0x1199, 0x6815) }, /* Sierra Wireless MC8775 */ { USB_DEVICE(0x03f0, 0x1e1d) }, /* HP hs2300 a.k.a MC8775 */ { USB_DEVICE(0x1199, 0x6820) }, /* Sierra Wireless AirCard 875 */ { USB_DEVICE(0x1199, 0x6821) }, /* Sierra Wireless AirCard 875U */ - { USB_DEVICE(0x1199, 0x6832) }, /* Sierra Wireless MC8780*/ - { USB_DEVICE(0x1199, 0x6833) }, /* Sierra Wireless MC8781*/ - { USB_DEVICE(0x1199, 0x683B), .driver_info = DEVICE_1_PORT }, /* Sierra Wireless MC8785 Composite*/ + { USB_DEVICE(0x1199, 0x6832) }, /* Sierra Wireless MC8780 */ + { USB_DEVICE(0x1199, 0x6833) }, /* Sierra Wireless MC8781 */ + { USB_DEVICE(0x1199, 0x683B), .driver_info = DEVICE_1_PORT }, /* Sierra Wireless MC8785 Composite */ { USB_DEVICE(0x1199, 0x6850) }, /* Sierra Wireless AirCard 880 */ { USB_DEVICE(0x1199, 0x6851) }, /* Sierra Wireless AirCard 881 */ { USB_DEVICE(0x1199, 0x6852) }, /* Sierra Wireless AirCard 880 E */ @@ -214,9 +219,6 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(0x1199, 0x6859), .driver_info = DEVICE_1_PORT }, /* Sierra Wireless AirCard 885 E */ { USB_DEVICE(0x1199, 0x685A), .driver_info = DEVICE_1_PORT }, /* Sierra Wireless AirCard 885 E */ - { USB_DEVICE(0x1199, 0x6468) }, /* Sierra Wireless MP3G - EVDO */ - { USB_DEVICE(0x1199, 0x6469) }, /* Sierra Wireless MP3G - UMTS/HSPA */ - { USB_DEVICE(0x1199, 0x0112), .driver_info = DEVICE_1_PORT }, /* Sierra Wireless AirCard 580 */ { USB_DEVICE(0x0F3D, 0x0112), .driver_info = DEVICE_1_PORT }, /* Airprime/Sierra PC 5220 */ @@ -713,7 +715,7 @@ static void sierra_shutdown(struct usb_serial *serial) static struct usb_serial_driver sierra_device = { .driver = { .owner = THIS_MODULE, - .name = "sierra1", + .name = "sierra", }, .description = "Sierra USB modem", .id_table = id_table, @@ -769,14 +771,10 @@ MODULE_DESCRIPTION(DRIVER_DESC); MODULE_VERSION(DRIVER_VERSION); MODULE_LICENSE("GPL"); -module_param(truinstall, bool, 0); -MODULE_PARM_DESC(truinstall, "TRU-Install support"); - -module_param(nmea, bool, 0); +module_param(nmea, bool, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(nmea, "NMEA streaming"); #ifdef CONFIG_USB_DEBUG module_param(debug, bool, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(debug, "Debug messages"); #endif - -- GitLab From e3173b22eb7b50a23af60e12bab7a29d4b24f284 Mon Sep 17 00:00:00 2001 From: Kevin Lloyd Date: Thu, 10 Jul 2008 14:14:51 -0700 Subject: [PATCH 288/750] USB Serial Sierra: Dynamic interface detection This patch changes the method by which the number of ports per interface is assigned so that it is more dynamic and calculated on the fly (as opposed to hard coding it). This will allow for faster and easier addition of products. Signed-off-by: Kevin Lloyd Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/sierra.c | 83 +++++++++++++++++++++++-------------- 1 file changed, 52 insertions(+), 31 deletions(-) diff --git a/drivers/usb/serial/sierra.c b/drivers/usb/serial/sierra.c index a3aaf08e56d..e2a7463346f 100644 --- a/drivers/usb/serial/sierra.c +++ b/drivers/usb/serial/sierra.c @@ -137,6 +137,8 @@ static int sierra_probe(struct usb_serial *serial, struct usb_device *udev; int *num_ports; u8 ifnum; + u8 numendpoints; + dev_dbg(&serial->dev->dev, "%s", __func__); num_ports = kmalloc(sizeof(*num_ports), GFP_KERNEL); @@ -144,23 +146,22 @@ static int sierra_probe(struct usb_serial *serial, return -ENOMEM; ifnum = serial->interface->cur_altsetting->desc.bInterfaceNumber; + numendpoints = serial->interface->cur_altsetting->desc.bNumEndpoints; udev = serial->dev; - /* Figure out the interface number from the serial structure */ - ifnum = sierra_calc_interface(serial); - - /* - * If this interface supports more than 1 alternate - * select the 2nd one - */ - if (serial->interface->num_altsetting == 2) { - dev_dbg(&udev->dev, - "Selecting alt setting for interface %d\n", - ifnum); + /* Figure out the interface number from the serial structure */ + ifnum = sierra_calc_interface(serial); - /* We know the alternate setting is 1 for the MC8785 */ - usb_set_interface(udev, ifnum, 1); - } + /* + * If this interface supports more than 1 alternate + * select the 2nd one + */ + if (serial->interface->num_altsetting == 2) { + dev_dbg(&udev->dev, "Selecting alt setting for interface %d\n", + ifnum); + /* We know the alternate setting is 1 for the MC8785 */ + usb_set_interface(udev, ifnum, 1); + } /* Check if in installer mode */ if (truinstall && id->driver_info == DEVICE_INSTALLER) { @@ -169,12 +170,14 @@ static int sierra_probe(struct usb_serial *serial, /* Don't bind to the device when in installer mode */ kfree(num_ports); return -EIO; - } else if (id->driver_info == DEVICE_1_PORT) - *num_ports = 1; - else if (ifnum == 0x99) + /* Dummy interface present on some SKUs should be ignored */ + } else if (ifnum == 0x99) *num_ports = 0; + else if (numendpoints <= 3) + *num_ports = 1; else - *num_ports = 3; + *num_ports = (numendpoints-1)/2; + /* * save off our num_ports info so that we can use it in the * calc_num_ports callback @@ -197,6 +200,9 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(0x1199, 0x0120) }, /* Sierra Wireless USB Dongle 595U */ /* Sierra Wireless C597 */ { USB_DEVICE_AND_INTERFACE_INFO(0x1199, 0x0023, 0xFF, 0xFF, 0xFF) }, + /* Sierra Wireless Device */ + { USB_DEVICE_AND_INTERFACE_INFO(0x1199, 0x0025, 0xFF, 0xFF, 0xFF) }, + { USB_DEVICE(0x1199, 0x0026) }, /* Sierra Wireless Device */ { USB_DEVICE(0x1199, 0x6802) }, /* Sierra Wireless MC8755 */ { USB_DEVICE(0x1199, 0x6804) }, /* Sierra Wireless MC8755 */ @@ -209,18 +215,27 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(0x1199, 0x6821) }, /* Sierra Wireless AirCard 875U */ { USB_DEVICE(0x1199, 0x6832) }, /* Sierra Wireless MC8780 */ { USB_DEVICE(0x1199, 0x6833) }, /* Sierra Wireless MC8781 */ - { USB_DEVICE(0x1199, 0x683B), .driver_info = DEVICE_1_PORT }, /* Sierra Wireless MC8785 Composite */ + { USB_DEVICE(0x1199, 0x683B) }, /* Sierra Wireless MC8785 Composite */ + { USB_DEVICE(0x1199, 0x683C) }, /* Sierra Wireless MC8790 */ + { USB_DEVICE(0x1199, 0x683D) }, /* Sierra Wireless MC8790 */ + { USB_DEVICE(0x1199, 0x683E) }, /* Sierra Wireless MC8790 */ { USB_DEVICE(0x1199, 0x6850) }, /* Sierra Wireless AirCard 880 */ { USB_DEVICE(0x1199, 0x6851) }, /* Sierra Wireless AirCard 881 */ { USB_DEVICE(0x1199, 0x6852) }, /* Sierra Wireless AirCard 880 E */ { USB_DEVICE(0x1199, 0x6853) }, /* Sierra Wireless AirCard 881 E */ { USB_DEVICE(0x1199, 0x6855) }, /* Sierra Wireless AirCard 880 U */ { USB_DEVICE(0x1199, 0x6856) }, /* Sierra Wireless AirCard 881 U */ - { USB_DEVICE(0x1199, 0x6859), .driver_info = DEVICE_1_PORT }, /* Sierra Wireless AirCard 885 E */ - { USB_DEVICE(0x1199, 0x685A), .driver_info = DEVICE_1_PORT }, /* Sierra Wireless AirCard 885 E */ - - { USB_DEVICE(0x1199, 0x0112), .driver_info = DEVICE_1_PORT }, /* Sierra Wireless AirCard 580 */ - { USB_DEVICE(0x0F3D, 0x0112), .driver_info = DEVICE_1_PORT }, /* Airprime/Sierra PC 5220 */ + { USB_DEVICE(0x1199, 0x6859) }, /* Sierra Wireless AirCard 885 E */ + { USB_DEVICE(0x1199, 0x685A) }, /* Sierra Wireless AirCard 885 E */ + /* Sierra Wireless C885 */ + { USB_DEVICE_AND_INTERFACE_INFO(0x1199, 0x6880, 0xFF, 0xFF, 0xFF)}, + /* Sierra Wireless Device */ + { USB_DEVICE_AND_INTERFACE_INFO(0x1199, 0x6890, 0xFF, 0xFF, 0xFF)}, + /* Sierra Wireless Device */ + { USB_DEVICE_AND_INTERFACE_INFO(0x1199, 0x6892, 0xFF, 0xFF, 0xFF)}, + + { USB_DEVICE(0x1199, 0x0112) }, /* Sierra Wireless AirCard 580 */ + { USB_DEVICE(0x0F3D, 0x0112) }, /* Airprime/Sierra PC 5220 */ { USB_DEVICE(0x1199, 0x0FFF), .driver_info = DEVICE_INSTALLER}, { } @@ -270,13 +285,19 @@ static int sierra_send_setup(struct tty_struct *tty, if (portdata->rts_state) val |= 0x02; - /* Determine which port is targeted */ - if (port->bulk_out_endpointAddress == 2) - interface = 0; - else if (port->bulk_out_endpointAddress == 4) - interface = 1; - else if (port->bulk_out_endpointAddress == 5) - interface = 2; + /* If composite device then properly report interface */ + if (serial->num_ports == 1) + interface = sierra_calc_interface(serial); + + /* Otherwise the need to do non-composite mapping */ + else { + if (port->bulk_out_endpointAddress == 2) + interface = 0; + else if (port->bulk_out_endpointAddress == 4) + interface = 1; + else if (port->bulk_out_endpointAddress == 5) + interface = 2; + } return usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), -- GitLab From 0585e4dfe5670d3ccb77bf86551a657699e9e52e Mon Sep 17 00:00:00 2001 From: Kevin Lloyd Date: Thu, 10 Jul 2008 14:14:54 -0700 Subject: [PATCH 289/750] USB Serial Sierra: TRU-Install feature update Moves responsbility of TRU-Install (i.e. ZeroCD) to the usb-storage driver. See patch 04/04 of this set. Signed-off-by: Kevin Lloyd Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/Kconfig | 7 ++++--- drivers/usb/serial/sierra.c | 35 +++-------------------------------- 2 files changed, 7 insertions(+), 35 deletions(-) diff --git a/drivers/usb/serial/Kconfig b/drivers/usb/serial/Kconfig index 8878c1767fc..70338f4ec91 100644 --- a/drivers/usb/serial/Kconfig +++ b/drivers/usb/serial/Kconfig @@ -499,9 +499,10 @@ config USB_SERIAL_SAFE_PADDED config USB_SERIAL_SIERRAWIRELESS tristate "USB Sierra Wireless Driver" help - Say M here if you want to use a Sierra Wireless device (if - using an PC 5220 or AC580 please use the Airprime driver - instead). + Say M here if you want to use Sierra Wireless devices. + + Many deviecs have a feature known as TRU-Install, for those devices + to work properly the USB Storage Sierra feature must be enabled. To compile this driver as a module, choose M here: the module will be called sierra. diff --git a/drivers/usb/serial/sierra.c b/drivers/usb/serial/sierra.c index e2a7463346f..6b7ed333386 100644 --- a/drivers/usb/serial/sierra.c +++ b/drivers/usb/serial/sierra.c @@ -14,7 +14,7 @@ Whom based his on the Keyspan driver by Hugh Blemings */ -#define DRIVER_VERSION "v.1.2.9c" +#define DRIVER_VERSION "v.1.2.13a" #define DRIVER_AUTHOR "Kevin Lloyd " #define DRIVER_DESC "USB Driver for Sierra Wireless USB modems" @@ -31,6 +31,7 @@ #define SWIMS_USB_REQUEST_SetPower 0x00 #define SWIMS_USB_REQUEST_SetNmea 0x07 #define SWIMS_USB_REQUEST_SetMode 0x0B +#define SWIMS_USB_REQUEST_GetSwocInfo 0x0A #define SWIMS_SET_MODE_Modem 0x0001 /* per port private data */ @@ -40,13 +41,6 @@ static int debug; static int nmea; -static int truinstall = 1; - -enum devicetype { - DEVICE_3_PORT = 0, - DEVICE_1_PORT = 1, - DEVICE_INSTALLER = 2, -}; static int sierra_set_power_state(struct usb_device *udev, __u16 swiState) { @@ -63,21 +57,6 @@ static int sierra_set_power_state(struct usb_device *udev, __u16 swiState) return result; } -static int sierra_set_ms_mode(struct usb_device *udev, __u16 eSWocMode) -{ - int result; - dev_dbg(&udev->dev, "%s", __func__); - result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), - SWIMS_USB_REQUEST_SetMode, /* __u8 request */ - USB_TYPE_VENDOR, /* __u8 request type */ - eSWocMode, /* __u16 value */ - 0x0000, /* __u16 index */ - NULL, /* void *data */ - 0, /* __u16 size */ - USB_CTRL_SET_TIMEOUT); /* int timeout */ - return result; -} - static int sierra_vsc_set_nmea(struct usb_device *udev, __u16 enable) { int result; @@ -163,15 +142,8 @@ static int sierra_probe(struct usb_serial *serial, usb_set_interface(udev, ifnum, 1); } - /* Check if in installer mode */ - if (truinstall && id->driver_info == DEVICE_INSTALLER) { - dev_dbg(&udev->dev, "%s", "FOUND TRU-INSTALL DEVICE(SW)\n"); - result = sierra_set_ms_mode(udev, SWIMS_SET_MODE_Modem); - /* Don't bind to the device when in installer mode */ - kfree(num_ports); - return -EIO; /* Dummy interface present on some SKUs should be ignored */ - } else if (ifnum == 0x99) + if (ifnum == 0x99) *num_ports = 0; else if (numendpoints <= 3) *num_ports = 1; @@ -237,7 +209,6 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(0x1199, 0x0112) }, /* Sierra Wireless AirCard 580 */ { USB_DEVICE(0x0F3D, 0x0112) }, /* Airprime/Sierra PC 5220 */ - { USB_DEVICE(0x1199, 0x0FFF), .driver_info = DEVICE_INSTALLER}, { } }; MODULE_DEVICE_TABLE(usb, id_table); -- GitLab From 32fe5e393455d87db4988af03915634304870fb4 Mon Sep 17 00:00:00 2001 From: Kevin Lloyd Date: Thu, 10 Jul 2008 14:14:57 -0700 Subject: [PATCH 290/750] USB Storage Sierra: TRU-Install feature update This patch upgrades the support for the Sierra Wireless TRU-Install feature (i.e. zeroCD) to allow for future support of Linux enabled TRU-Install devices. By default all devices that do not have a Linux enabled TRU-Install device (i.e. the device does not have a Linux package on the virtual CD partition) will be switched into "modem mode." Devices that do contain a Linux package in the TRU-Install virtual CD will be allowed to enumerate as a CD-Rom so that either (a) a user can install the packaged software or (b) a user-space application (e.g. udev) can switch it to modem mode. This patch does allow for manual override by adding a usb-storage module parameter 'swi_tru_install' which can force the modem into either mode regardless of what packages it contains. Signed-off-by: Kevin Lloyd Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/Kconfig | 12 ++ drivers/usb/storage/Makefile | 1 + drivers/usb/storage/sierra_ms.c | 207 +++++++++++++++++++++++++++++ drivers/usb/storage/sierra_ms.h | 4 + drivers/usb/storage/unusual_devs.h | 6 +- drivers/usb/storage/usb.c | 3 + 6 files changed, 231 insertions(+), 2 deletions(-) create mode 100644 drivers/usb/storage/sierra_ms.c create mode 100644 drivers/usb/storage/sierra_ms.h diff --git a/drivers/usb/storage/Kconfig b/drivers/usb/storage/Kconfig index 3d9249632ae..c76034672c1 100644 --- a/drivers/usb/storage/Kconfig +++ b/drivers/usb/storage/Kconfig @@ -146,6 +146,18 @@ config USB_STORAGE_KARMA on the resulting scsi device node returns the Karma to normal operation. +config USB_STORAGE_SIERRA + bool "Sierra Wireless TRU-Install Feature Support" + depends on USB_STORAGE + help + Say Y here to include additional code to support Sierra Wireless + products with the TRU-Install feature (e.g., AC597E, AC881U). + + This code switches the Sierra Wireless device from being in + Mass Storage mode to Modem mode. It also has the ability to + support host software upgrades should full Linux support be added + to TRU-Install. + config USB_STORAGE_CYPRESS_ATACB bool "SAT emulation on Cypress USB/ATA Bridge with ATACB" depends on USB_STORAGE diff --git a/drivers/usb/storage/Makefile b/drivers/usb/storage/Makefile index 4c596c766c5..bc3415b475c 100644 --- a/drivers/usb/storage/Makefile +++ b/drivers/usb/storage/Makefile @@ -21,6 +21,7 @@ usb-storage-obj-$(CONFIG_USB_STORAGE_JUMPSHOT) += jumpshot.o usb-storage-obj-$(CONFIG_USB_STORAGE_ALAUDA) += alauda.o usb-storage-obj-$(CONFIG_USB_STORAGE_ONETOUCH) += onetouch.o usb-storage-obj-$(CONFIG_USB_STORAGE_KARMA) += karma.o +usb-storage-obj-$(CONFIG_USB_STORAGE_SIERRA) += sierra_ms.o usb-storage-obj-$(CONFIG_USB_STORAGE_CYPRESS_ATACB) += cypress_atacb.o usb-storage-objs := scsiglue.o protocol.o transport.o usb.o \ diff --git a/drivers/usb/storage/sierra_ms.c b/drivers/usb/storage/sierra_ms.c new file mode 100644 index 00000000000..4359a2cb42d --- /dev/null +++ b/drivers/usb/storage/sierra_ms.c @@ -0,0 +1,207 @@ +#include +#include +#include +#include +#include + +#include "usb.h" +#include "transport.h" +#include "protocol.h" +#include "scsiglue.h" +#include "sierra_ms.h" +#include "debug.h" + +#define SWIMS_USB_REQUEST_SetSwocMode 0x0B +#define SWIMS_USB_REQUEST_GetSwocInfo 0x0A +#define SWIMS_USB_INDEX_SetMode 0x0000 +#define SWIMS_SET_MODE_Modem 0x0001 + +#define TRU_NORMAL 0x01 +#define TRU_FORCE_MS 0x02 +#define TRU_FORCE_MODEM 0x03 + +static unsigned int swi_tru_install = 1; +module_param(swi_tru_install, uint, S_IRUGO | S_IWUSR); +MODULE_PARM_DESC(swi_tru_install, "TRU-Install mode (1=Full Logic (def)," + " 2=Force CD-Rom, 3=Force Modem)"); + +struct swoc_info { + __u8 rev; + __u8 reserved[8]; + __u16 LinuxSKU; + __u16 LinuxVer; + __u8 reserved2[47]; +} __attribute__((__packed__)); + +static bool containsFullLinuxPackage(struct swoc_info *swocInfo) +{ + if ((swocInfo->LinuxSKU >= 0x2100 && swocInfo->LinuxSKU <= 0x2FFF) || + (swocInfo->LinuxSKU >= 0x7100 && swocInfo->LinuxSKU <= 0x7FFF)) + return true; + else + return false; +} + +static int sierra_set_ms_mode(struct usb_device *udev, __u16 eSWocMode) +{ + int result; + US_DEBUGP("SWIMS: %s", "DEVICE MODE SWITCH\n"); + result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), + SWIMS_USB_REQUEST_SetSwocMode, /* __u8 request */ + USB_TYPE_VENDOR | USB_DIR_OUT, /* __u8 request type */ + eSWocMode, /* __u16 value */ + 0x0000, /* __u16 index */ + NULL, /* void *data */ + 0, /* __u16 size */ + USB_CTRL_SET_TIMEOUT); /* int timeout */ + return result; +} + + +static int sierra_get_swoc_info(struct usb_device *udev, + struct swoc_info *swocInfo) +{ + int result; + + US_DEBUGP("SWIMS: Attempting to get TRU-Install info.\n"); + + result = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), + SWIMS_USB_REQUEST_GetSwocInfo, /* __u8 request */ + USB_TYPE_VENDOR | USB_DIR_IN, /* __u8 request type */ + 0, /* __u16 value */ + 0, /* __u16 index */ + (void *) swocInfo, /* void *data */ + sizeof(struct swoc_info), /* __u16 size */ + USB_CTRL_SET_TIMEOUT); /* int timeout */ + + swocInfo->LinuxSKU = le16_to_cpu(swocInfo->LinuxSKU); + swocInfo->LinuxVer = le16_to_cpu(swocInfo->LinuxVer); + return result; +} + +static void debug_swoc(struct swoc_info *swocInfo) +{ + US_DEBUGP("SWIMS: SWoC Rev: %02d \n", swocInfo->rev); + US_DEBUGP("SWIMS: Linux SKU: %04X \n", swocInfo->LinuxSKU); + US_DEBUGP("SWIMS: Linux Version: %04X \n", swocInfo->LinuxVer); +} + + +static ssize_t show_truinst(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct swoc_info *swocInfo; + struct usb_interface *intf = to_usb_interface(dev); + struct usb_device *udev = interface_to_usbdev(intf); + int result; + if (swi_tru_install == TRU_FORCE_MS) { + result = snprintf(buf, PAGE_SIZE, "Forced Mass Storage\n"); + } else { + swocInfo = kmalloc(sizeof(struct swoc_info), GFP_KERNEL); + if (!swocInfo) { + US_DEBUGP("SWIMS: Allocation failure\n"); + snprintf(buf, PAGE_SIZE, "Error\n"); + return -ENOMEM; + } + result = sierra_get_swoc_info(udev, swocInfo); + if (result < 0) { + US_DEBUGP("SWIMS: failed SWoC query\n"); + kfree(swocInfo); + snprintf(buf, PAGE_SIZE, "Error\n"); + return -EIO; + } + debug_swoc(swocInfo); + result = snprintf(buf, PAGE_SIZE, + "REV=%02d SKU=%04X VER=%04X\n", + swocInfo->rev, + swocInfo->LinuxSKU, + swocInfo->LinuxVer); + kfree(swocInfo); + } + return result; +} +static DEVICE_ATTR(truinst, S_IWUGO | S_IRUGO, show_truinst, NULL); + +int sierra_ms_init(struct us_data *us) +{ + int result, retries; + signed long delay_t; + struct swoc_info *swocInfo; + struct usb_device *udev; + struct Scsi_Host *sh; + struct scsi_device *sd; + + delay_t = 2; + retries = 3; + result = 0; + udev = us->pusb_dev; + + sh = us_to_host(us); + sd = scsi_get_host_dev(sh); + + US_DEBUGP("SWIMS: sierra_ms_init called\n"); + + /* Force Modem mode */ + if (swi_tru_install == TRU_FORCE_MODEM) { + US_DEBUGP("SWIMS: %s", "Forcing Modem Mode\n"); + result = sierra_set_ms_mode(udev, SWIMS_SET_MODE_Modem); + if (result < 0) + US_DEBUGP("SWIMS: Failed to switch to modem mode.\n"); + return -EIO; + } + /* Force Mass Storage mode (keep CD-Rom) */ + else if (swi_tru_install == TRU_FORCE_MS) { + US_DEBUGP("SWIMS: %s", "Forcing Mass Storage Mode\n"); + goto complete; + } + /* Normal TRU-Install Logic */ + else { + US_DEBUGP("SWIMS: %s", "Normal SWoC Logic\n"); + + swocInfo = kmalloc(sizeof(struct swoc_info), + GFP_KERNEL); + if (!swocInfo) { + US_DEBUGP("SWIMS: %s", "Allocation failure\n"); + return -ENOMEM; + } + + retries = 3; + do { + retries--; + result = sierra_get_swoc_info(udev, swocInfo); + if (result < 0) { + US_DEBUGP("SWIMS: %s", "Failed SWoC query\n"); + schedule_timeout_uninterruptible(2*HZ); + } + } while (retries && result < 0); + + if (result < 0) { + US_DEBUGP("SWIMS: %s", + "Completely failed SWoC query\n"); + kfree(swocInfo); + return -EIO; + } + + debug_swoc(swocInfo); + + /* If there is not Linux software on the TRU-Install device + * then switch to modem mode + */ + if (!containsFullLinuxPackage(swocInfo)) { + US_DEBUGP("SWIMS: %s", + "Switching to Modem Mode\n"); + result = sierra_set_ms_mode(udev, + SWIMS_SET_MODE_Modem); + if (result < 0) + US_DEBUGP("SWIMS: Failed to switch modem\n"); + kfree(swocInfo); + return -EIO; + } + kfree(swocInfo); + } +complete: + result = device_create_file(&us->pusb_intf->dev, &dev_attr_truinst); + + return USB_STOR_TRANSPORT_GOOD; +} + diff --git a/drivers/usb/storage/sierra_ms.h b/drivers/usb/storage/sierra_ms.h new file mode 100644 index 00000000000..bb48634ac1f --- /dev/null +++ b/drivers/usb/storage/sierra_ms.h @@ -0,0 +1,4 @@ +#ifndef _SIERRA_MS_H_ +#define _SIERRA_MS_H_ +extern int sierra_ms_init(struct us_data *us); +#endif diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h index 11249bf5d74..927572377f3 100644 --- a/drivers/usb/storage/unusual_devs.h +++ b/drivers/usb/storage/unusual_devs.h @@ -1569,6 +1569,7 @@ UNUSUAL_DEV( 0x10d6, 0x2200, 0x0100, 0x0100, US_SC_DEVICE, US_PR_DEVICE, NULL, 0), +#ifdef CONFIG_USB_STORAGE_SIERRA /* Reported by Kevin Lloyd * Entry is needed for the initializer function override, * which instructs the device to load as a modem @@ -1577,8 +1578,9 @@ UNUSUAL_DEV( 0x10d6, 0x2200, 0x0100, 0x0100, UNUSUAL_DEV( 0x1199, 0x0fff, 0x0000, 0x9999, "Sierra Wireless", "USB MMC Storage", - US_SC_DEVICE, US_PR_DEVICE, NULL, - US_FL_IGNORE_DEVICE), + US_SC_DEVICE, US_PR_DEVICE, sierra_ms_init, + 0), +#endif /* Reported by Jaco Kroon * The usb-storage module found on the Digitech GNX4 (and supposedly other diff --git a/drivers/usb/storage/usb.c b/drivers/usb/storage/usb.c index bfea851be98..73679aa506d 100644 --- a/drivers/usb/storage/usb.c +++ b/drivers/usb/storage/usb.c @@ -102,6 +102,9 @@ #ifdef CONFIG_USB_STORAGE_CYPRESS_ATACB #include "cypress_atacb.h" #endif +#ifdef CONFIG_USB_STORAGE_SIERRA +#include "sierra_ms.h" +#endif /* Some informational data */ MODULE_AUTHOR("Matthew Dharm "); -- GitLab From 51cdc1c103dcb7cf1ca280843308a2e32847f9ce Mon Sep 17 00:00:00 2001 From: Jost Diederichs Date: Sat, 12 Jul 2008 22:37:05 -0700 Subject: [PATCH 291/750] USB: usb-storage Motorola Phone Razr v3xx US_FL_FIX_CAPACITY patch add razr v3xx US_FL_FIX_CAPACITY flag to unusual_devs.h in usb-storage This is another Motorola phone that incorrectly reports the sector count (off by one). Problem Description: io errors when mounting phone's sd-card via the phones usb port Steps to reproduce: mount Motorola Razr v3xx phones sd-card on Linux Desktop via usb cable. Phones USB port must be in memory card mode. DEBUG output: Jul 9 19:32:41 micky kernel: Buffer I/O error on device sdd, logical block 3970048 Jul 9 19:32:41 micky kernel: sd 11:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK Jul 9 19:32:41 micky kernel: sd 11:0:0:0: [sdd] Sense Key : Medium Error [current] Jul 9 19:32:41 micky kernel: sd 11:0:0:0: [sdd] Add. Sense: No additional sense information Jul 9 19:32:41 micky kernel: end_request: I/O error, dev sdd, sector 3970048 From: Jost Diederichs Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/unusual_devs.h | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h index 927572377f3..564999c42d7 100644 --- a/drivers/usb/storage/unusual_devs.h +++ b/drivers/usb/storage/unusual_devs.h @@ -1751,6 +1751,15 @@ UNUSUAL_DEV( 0x22b8, 0x4810, 0x0001, 0x0002, US_SC_DEVICE, US_PR_DEVICE, NULL, US_FL_FIX_CAPACITY), +/* + * Patch by Jost Diederichs + */ +UNUSUAL_DEV(0x22b8, 0x6410, 0x0001, 0x9999, + "Motorola Inc.", + "Motorola Phone (RAZRV3xx)", + US_SC_DEVICE, US_PR_DEVICE, NULL, + US_FL_FIX_CAPACITY), + /* * Patch by Constantin Baranov * Report by Andreas Koenecke. -- GitLab From 230ffc75b7b842db5710d30d3a2fc61f9d6f50df Mon Sep 17 00:00:00 2001 From: Simon Arlott Date: Sat, 12 Jul 2008 22:19:48 +0100 Subject: [PATCH 292/750] USB: cxacru: Fix printk format flag in error message "#%x" should have been "%#x" Signed-off-by: Simon Arlott Signed-off-by: Greg Kroah-Hartman --- drivers/usb/atm/cxacru.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/atm/cxacru.c b/drivers/usb/atm/cxacru.c index 507a9bd0d77..9aea43a8c4a 100644 --- a/drivers/usb/atm/cxacru.c +++ b/drivers/usb/atm/cxacru.c @@ -602,7 +602,7 @@ static int cxacru_cm_get_array(struct cxacru_data *instance, enum cxacru_cm_requ offd = le32_to_cpu(buf[offb++]); if (offd >= size) { if (printk_ratelimit()) - usb_err(instance->usbatm, "wrong index #%x in response to cm #%x\n", + usb_err(instance->usbatm, "wrong index %#x in response to cm %#x\n", offd, cm); ret = -EIO; goto cleanup; -- GitLab From f0fa74634c0c686618b5318748bde233772a1a8d Mon Sep 17 00:00:00 2001 From: Oliver Neukum Date: Fri, 4 Jul 2008 10:10:53 +0200 Subject: [PATCH 293/750] USB: update to Documentation this mentions a new deadlock due to advanced power management. Signed-off-by: Oliver Neukum Signed-off-by: Greg Kroah-Hartman --- Documentation/usb/power-management.txt | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/Documentation/usb/power-management.txt b/Documentation/usb/power-management.txt index b2fc4d4a991..9d31140e3f5 100644 --- a/Documentation/usb/power-management.txt +++ b/Documentation/usb/power-management.txt @@ -436,7 +436,12 @@ post_reset; the USB core guarantees that this is true of internal suspend/resume events as well. If a driver wants to block all suspend/resume calls during some -critical section, it can simply acquire udev->pm_mutex. +critical section, it can simply acquire udev->pm_mutex. Note that +calls to resume may be triggered indirectly. Block IO due to memory +allocations can make the vm subsystem resume a device. Thus while +holding this lock you must not allocate memory with GFP_KERNEL or +GFP_NOFS. + Alternatively, if the critical section might call some of the usb_autopm_* routines, the driver can avoid deadlock by doing: -- GitLab From 1133cd8adf34709e1857d1491e9fae5597b51ad5 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Sun, 6 Jul 2008 23:35:01 +0400 Subject: [PATCH 294/750] USB: ohci: make distrust_firmware a quirk Signed-off-by: Dmitry Baryshkov Acked-by: David Brownell Cc: Alan Stern Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ohci-hcd.c | 6 +++++- drivers/usb/host/ohci-omap.c | 2 +- drivers/usb/host/ohci.h | 1 + 3 files changed, 7 insertions(+), 2 deletions(-) diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c index 26bc47941d0..96fe76e9a6c 100644 --- a/drivers/usb/host/ohci-hcd.c +++ b/drivers/usb/host/ohci-hcd.c @@ -483,6 +483,9 @@ static int ohci_init (struct ohci_hcd *ohci) int ret; struct usb_hcd *hcd = ohci_to_hcd(ohci); + if (distrust_firmware) + ohci->flags |= OHCI_QUIRK_HUB_POWER; + disable (ohci); ohci->regs = hcd->regs; @@ -689,7 +692,8 @@ retry: temp |= RH_A_NOCP; temp &= ~(RH_A_POTPGT | RH_A_NPS); ohci_writel (ohci, temp, &ohci->regs->roothub.a); - } else if ((ohci->flags & OHCI_QUIRK_AMD756) || distrust_firmware) { + } else if ((ohci->flags & OHCI_QUIRK_AMD756) || + (ohci->flags & OHCI_QUIRK_HUB_POWER)) { /* hub power always on; required for AMD-756 and some * Mac platforms. ganged overcurrent reporting, if any. */ diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c index 94dfca02f7e..5b2f17838ca 100644 --- a/drivers/usb/host/ohci-omap.c +++ b/drivers/usb/host/ohci-omap.c @@ -260,7 +260,7 @@ static int ohci_omap_init(struct usb_hcd *hcd) omap_cfg_reg(W4_USB_HIGHZ); } ohci_writel(ohci, rh, &ohci->regs->roothub.a); - distrust_firmware = 0; + ohci->flags &= ~OHCI_QUIRK_HUB_POWER; } else if (machine_is_nokia770()) { /* We require a self-powered hub, which should have * plenty of power. */ diff --git a/drivers/usb/host/ohci.h b/drivers/usb/host/ohci.h index dc544ddc784..73b4a44c272 100644 --- a/drivers/usb/host/ohci.h +++ b/drivers/usb/host/ohci.h @@ -399,6 +399,7 @@ struct ohci_hcd { #define OHCI_QUIRK_ZFMICRO 0x20 /* Compaq ZFMicro chipset*/ #define OHCI_QUIRK_NEC 0x40 /* lost interrupts */ #define OHCI_QUIRK_FRAME_NO 0x80 /* no big endian frame_no shift */ +#define OHCI_QUIRK_HUB_POWER 0x100 /* distrust firmware power/oc setup */ // there are also chip quirks/bugs in init logic struct work_struct nec_work; /* Worker for NEC quirk */ -- GitLab From e8b24450a635bbbd3a2b4c2649eef060c742ebc0 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Sun, 6 Jul 2008 14:26:30 +0400 Subject: [PATCH 295/750] USB: Hook start_hnp into ohci struct Signed-off-by: Dmitry Baryshkov Acked-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ohci-hub.c | 4 +--- drivers/usb/host/ohci-omap.c | 1 + drivers/usb/host/ohci.h | 1 + 3 files changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/usb/host/ohci-hub.c b/drivers/usb/host/ohci-hub.c index d54183f1d70..439beb784f3 100644 --- a/drivers/usb/host/ohci-hub.c +++ b/drivers/usb/host/ohci-hub.c @@ -579,8 +579,6 @@ static int ohci_start_port_reset (struct usb_hcd *hcd, unsigned port) return 0; } -static void start_hnp(struct ohci_hcd *ohci); - #else #define ohci_start_port_reset NULL @@ -767,7 +765,7 @@ static int ohci_hub_control ( #ifdef CONFIG_USB_OTG if (hcd->self.otg_port == (wIndex + 1) && hcd->self.b_hnp_enable) - start_hnp(ohci); + ohci->start_hnp(ohci); else #endif ohci_writel (ohci, RH_PS_PSS, diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c index 5b2f17838ca..3d532b70967 100644 --- a/drivers/usb/host/ohci-omap.c +++ b/drivers/usb/host/ohci-omap.c @@ -225,6 +225,7 @@ static int ohci_omap_init(struct usb_hcd *hcd) dev_err(hcd->self.controller, "can't find transceiver\n"); return -ENODEV; } + ohci->start_hnp = start_hnp; } #endif diff --git a/drivers/usb/host/ohci.h b/drivers/usb/host/ohci.h index 73b4a44c272..df5a8037dba 100644 --- a/drivers/usb/host/ohci.h +++ b/drivers/usb/host/ohci.h @@ -371,6 +371,7 @@ struct ohci_hcd { * other external transceivers should be software-transparent */ struct otg_transceiver *transceiver; + void (*start_hnp)(struct ohci_hcd *ohci); /* * memory management for queue data structures -- GitLab From 937ef73d5075997a8d1777abf217a48bef2ce029 Mon Sep 17 00:00:00 2001 From: David Brownell Date: Mon, 7 Jul 2008 12:16:08 -0700 Subject: [PATCH 296/750] USB: serial gadget: rx path data loss fixes Update RX path handling in new serial gadget code to cope better with RX blockage: queue every RX packet until its contents can safely be passed up to the ldisc. Most of the RX path work is now done in the RX tasklet, instead of just the final "push to ldisc" step. This addresses some cases of data loss: - A longstanding serial gadget bug: when tty_insert_flip_string() didn't copy the entire buffer, the rest of the characters were dropped! Now that packet stays queued until the rest of its data is pushed to the ldisc. - Another longstanding issue: in the unlikely case that an RX transfer returns data and also reports a fault, that data is no longer discarded. - In the recently added RX throttling logic: it needs to stop pushing data into the TTY layer, instead of just not submitting new USB read requests. When the TTY is throttled long enough, backpressure will eventually make the OUT endpoint NAK. Also: an #ifdef is removed (no longer necessary); and start switching to a better convention for debug messages (prefix them with tty name). Signed-off-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/u_serial.c | 236 +++++++++++++++++++++------------- 1 file changed, 146 insertions(+), 90 deletions(-) diff --git a/drivers/usb/gadget/u_serial.c b/drivers/usb/gadget/u_serial.c index abf9505d3a7..6641efa5563 100644 --- a/drivers/usb/gadget/u_serial.c +++ b/drivers/usb/gadget/u_serial.c @@ -52,6 +52,8 @@ * is managed in userspace ... OBEX, PTP, and MTP have been mentioned. */ +#define PREFIX "ttyGS" + /* * gserial is the lifecycle interface, used by USB functions * gs_port is the I/O nexus, used by the tty driver @@ -100,6 +102,8 @@ struct gs_port { wait_queue_head_t close_wait; /* wait for last close */ struct list_head read_pool; + struct list_head read_queue; + unsigned n_read; struct tasklet_struct push; struct list_head write_pool; @@ -367,11 +371,9 @@ __acquires(&port->port_lock) req->length = len; list_del(&req->list); -#ifdef VERBOSE_DEBUG - pr_debug("%s: %s, len=%d, 0x%02x 0x%02x 0x%02x ...\n", - __func__, in->name, len, *((u8 *)req->buf), + pr_vdebug(PREFIX "%d: tx len=%d, 0x%02x 0x%02x 0x%02x ...\n", + port->port_num, len, *((u8 *)req->buf), *((u8 *)req->buf+1), *((u8 *)req->buf+2)); -#endif /* Drop lock while we call out of driver; completions * could be issued while we do so. Disconnection may @@ -401,56 +403,6 @@ __acquires(&port->port_lock) return status; } -static void gs_rx_push(unsigned long _port) -{ - struct gs_port *port = (void *)_port; - struct tty_struct *tty = port->port_tty; - - /* With low_latency, tty_flip_buffer_push() doesn't put its - * real work through a workqueue, so the ldisc has a better - * chance to keep up with peak USB data rates. - */ - if (tty) { - tty_flip_buffer_push(tty); - wake_up_interruptible(&tty->read_wait); - } -} - -/* - * gs_recv_packet - * - * Called for each USB packet received. Reads the packet - * header and stuffs the data in the appropriate tty buffer. - * Returns 0 if successful, or a negative error number. - * - * Called during USB completion routine, on interrupt time. - * With port_lock. - */ -static int gs_recv_packet(struct gs_port *port, char *packet, unsigned size) -{ - unsigned len; - struct tty_struct *tty; - - /* I/O completions can continue for a while after close(), until the - * request queue empties. Just discard any data we receive, until - * something reopens this TTY ... as if there were no HW flow control. - */ - tty = port->port_tty; - if (tty == NULL) { - pr_vdebug("%s: ttyGS%d, after close\n", - __func__, port->port_num); - return -EIO; - } - - len = tty_insert_flip_string(tty, packet, size); - if (len > 0) - tasklet_schedule(&port->push); - if (len < size) - pr_debug("%s: ttyGS%d, drop %d bytes\n", - __func__, port->port_num, size - len); - return 0; -} - /* * Context: caller owns port_lock, and port_usb is set */ @@ -469,9 +421,9 @@ __acquires(&port->port_lock) int status; struct tty_struct *tty; - /* no more rx if closed or throttled */ + /* no more rx if closed */ tty = port->port_tty; - if (!tty || test_bit(TTY_THROTTLED, &tty->flags)) + if (!tty) break; req = list_entry(pool->next, struct usb_request, list); @@ -500,36 +452,134 @@ __acquires(&port->port_lock) return started; } -static void gs_read_complete(struct usb_ep *ep, struct usb_request *req) +/* + * RX tasklet takes data out of the RX queue and hands it up to the TTY + * layer until it refuses to take any more data (or is throttled back). + * Then it issues reads for any further data. + * + * If the RX queue becomes full enough that no usb_request is queued, + * the OUT endpoint may begin NAKing as soon as its FIFO fills up. + * So QUEUE_SIZE packets plus however many the FIFO holds (usually two) + * can be buffered before the TTY layer's buffers (currently 64 KB). + */ +static void gs_rx_push(unsigned long _port) { - int status; - struct gs_port *port = ep->driver_data; + struct gs_port *port = (void *)_port; + struct tty_struct *tty; + struct list_head *queue = &port->read_queue; + bool disconnect = false; + bool do_push = false; - spin_lock(&port->port_lock); - list_add(&req->list, &port->read_pool); + /* hand any queued data to the tty */ + spin_lock_irq(&port->port_lock); + tty = port->port_tty; + while (!list_empty(queue)) { + struct usb_request *req; - switch (req->status) { - case 0: - /* normal completion */ - status = gs_recv_packet(port, req->buf, req->actual); - if (status && status != -EIO) - pr_debug("%s: %s %s err %d\n", - __func__, "recv", ep->name, status); - gs_start_rx(port); - break; + req = list_first_entry(queue, struct usb_request, list); - case -ESHUTDOWN: - /* disconnect */ - pr_vdebug("%s: %s shutdown\n", __func__, ep->name); - break; + /* discard data if tty was closed */ + if (!tty) + goto recycle; - default: - /* presumably a transient fault */ - pr_warning("%s: unexpected %s status %d\n", - __func__, ep->name, req->status); - gs_start_rx(port); - break; + /* leave data queued if tty was rx throttled */ + if (test_bit(TTY_THROTTLED, &tty->flags)) + break; + + switch (req->status) { + case -ESHUTDOWN: + disconnect = true; + pr_vdebug(PREFIX "%d: shutdown\n", port->port_num); + break; + + default: + /* presumably a transient fault */ + pr_warning(PREFIX "%d: unexpected RX status %d\n", + port->port_num, req->status); + /* FALLTHROUGH */ + case 0: + /* normal completion */ + break; + } + + /* push data to (open) tty */ + if (req->actual) { + char *packet = req->buf; + unsigned size = req->actual; + unsigned n; + int count; + + /* we may have pushed part of this packet already... */ + n = port->n_read; + if (n) { + packet += n; + size -= n; + } + + count = tty_insert_flip_string(tty, packet, size); + if (count) + do_push = true; + if (count != size) { + /* stop pushing; TTY layer can't handle more */ + port->n_read += count; + pr_vdebug(PREFIX "%d: rx block %d/%d\n", + port->port_num, + count, req->actual); + break; + } + port->n_read = 0; + } +recycle: + list_move(&req->list, &port->read_pool); + } + + /* Push from tty to ldisc; this is immediate with low_latency, and + * may trigger callbacks to this driver ... so drop the spinlock. + */ + if (tty && do_push) { + spin_unlock_irq(&port->port_lock); + tty_flip_buffer_push(tty); + wake_up_interruptible(&tty->read_wait); + spin_lock_irq(&port->port_lock); + + /* tty may have been closed */ + tty = port->port_tty; } + + + /* We want our data queue to become empty ASAP, keeping data + * in the tty and ldisc (not here). If we couldn't push any + * this time around, there may be trouble unless there's an + * implicit tty_unthrottle() call on its way... + * + * REVISIT we should probably add a timer to keep the tasklet + * from starving ... but it's not clear that case ever happens. + */ + if (!list_empty(queue) && tty) { + if (!test_bit(TTY_THROTTLED, &tty->flags)) { + if (do_push) + tasklet_schedule(&port->push); + else + pr_warning(PREFIX "%d: RX not scheduled?\n", + port->port_num); + } + } + + /* If we're still connected, refill the USB RX queue. */ + if (!disconnect && port->port_usb) + gs_start_rx(port); + + spin_unlock_irq(&port->port_lock); +} + +static void gs_read_complete(struct usb_ep *ep, struct usb_request *req) +{ + struct gs_port *port = ep->driver_data; + + /* Queue all received data until the tty layer is ready for it. */ + spin_lock(&port->port_lock); + list_add_tail(&req->list, &port->read_queue); + tasklet_schedule(&port->push); spin_unlock(&port->port_lock); } @@ -625,6 +675,7 @@ static int gs_start_io(struct gs_port *port) } /* queue read requests */ + port->n_read = 0; started = gs_start_rx(port); /* unblock any pending writes into our circular buffer */ @@ -633,9 +684,10 @@ static int gs_start_io(struct gs_port *port) } else { gs_free_requests(ep, head); gs_free_requests(port->port_usb->in, &port->write_pool); + status = -EIO; } - return started ? 0 : status; + return status; } /*-------------------------------------------------------------------------*/ @@ -809,8 +861,6 @@ static void gs_close(struct tty_struct *tty, struct file *file) else gs_buf_clear(&port->port_write_buf); - tasklet_kill(&port->push); - tty->driver_data = NULL; port->port_tty = NULL; @@ -911,15 +961,17 @@ static void gs_unthrottle(struct tty_struct *tty) { struct gs_port *port = tty->driver_data; unsigned long flags; - unsigned started = 0; spin_lock_irqsave(&port->port_lock, flags); - if (port->port_usb) - started = gs_start_rx(port); + if (port->port_usb) { + /* Kickstart read queue processing. We don't do xon/xoff, + * rts/cts, or other handshaking with the host, but if the + * read queue backs up enough we'll be NAKing OUT packets. + */ + tasklet_schedule(&port->push); + pr_vdebug(PREFIX "%d: unthrottle\n", port->port_num); + } spin_unlock_irqrestore(&port->port_lock, flags); - - pr_vdebug("gs_unthrottle: ttyGS%d, %d packets\n", - port->port_num, started); } static const struct tty_operations gs_tty_ops = { @@ -953,6 +1005,7 @@ gs_port_alloc(unsigned port_num, struct usb_cdc_line_coding *coding) tasklet_init(&port->push, gs_rx_push, (unsigned long) port); INIT_LIST_HEAD(&port->read_pool); + INIT_LIST_HEAD(&port->read_queue); INIT_LIST_HEAD(&port->write_pool); port->port_num = port_num; @@ -997,7 +1050,7 @@ int __init gserial_setup(struct usb_gadget *g, unsigned count) gs_tty_driver->owner = THIS_MODULE; gs_tty_driver->driver_name = "g_serial"; - gs_tty_driver->name = "ttyGS"; + gs_tty_driver->name = PREFIX; /* uses dynamically assigned dev_t values */ gs_tty_driver->type = TTY_DRIVER_TYPE_SERIAL; @@ -1104,6 +1157,8 @@ void gserial_cleanup(void) ports[i].port = NULL; mutex_unlock(&ports[i].lock); + tasklet_kill(&port->push); + /* wait for old opens to finish */ wait_event(port->close_wait, gs_closed(port)); @@ -1241,6 +1296,7 @@ void gserial_disconnect(struct gserial *gser) if (port->open_count == 0 && !port->openclose) gs_buf_free(&port->port_write_buf); gs_free_requests(gser->out, &port->read_pool); + gs_free_requests(gser->out, &port->read_queue); gs_free_requests(gser->in, &port->write_pool); spin_unlock_irqrestore(&port->port_lock, flags); } -- GitLab From a36c27dfd1003e6d6842fe77faaf868e3e6e9062 Mon Sep 17 00:00:00 2001 From: Sebastian Siewior Date: Thu, 17 Jul 2008 20:09:28 +0200 Subject: [PATCH 297/750] usb: return error code instead of 0 in the enqueue function. if the enqueue function returns -ESHUTDOWN or -ENOMEM then we return 0 instead of an error. This leads to a timeout and then to a dequeue request of an not enqueued urb. Signed-off-by: Sebastian Siewior Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/isp1760-hcd.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/drivers/usb/host/isp1760-hcd.c b/drivers/usb/host/isp1760-hcd.c index c858f2adb92..db5f4f5c7a1 100644 --- a/drivers/usb/host/isp1760-hcd.c +++ b/drivers/usb/host/isp1760-hcd.c @@ -1615,8 +1615,7 @@ static int isp1760_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, return -EPIPE; } - isp1760_prepare_enqueue(priv, urb, &qtd_list, mem_flags, pe); - return 0; + return isp1760_prepare_enqueue(priv, urb, &qtd_list, mem_flags, pe); } static int isp1760_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, -- GitLab From 3f02a957d5eb0eeb01207a799086f2b347077f71 Mon Sep 17 00:00:00 2001 From: Enrico Scholz Date: Thu, 17 Jul 2008 20:09:30 +0200 Subject: [PATCH 298/750] usb: ISP1760: improve pre-fetch timing ISP1760 requires a delay of 90ns between programming the address and reading the data. Current driver solves this by a mdelay(1) which is very heavy weighted and slow. This patch applies the workaround from the ISP1760 FAQ by using two different banks for PTD and payload data and using a common wait for them. This wait is done by an additional ISP1760 access (whose timing constraints guarantee the 90ns delay). This improves speed when reading from an USB stick from: $ time dd if=/dev/sda of=/dev/zero bs=65536 count=1638 real 1m 15.43s user 0m 0.44s sys 0m 39.46s to $ time dd if=/dev/sda of=/dev/zero bs=65536 count=1638 real 0m 18.53s user 0m 0.16s sys 0m 12.97s [bigeasy@linutronix.de: fixed comment formating, moved define into header file, obey 80 char rule] Signed-off-by: Enrico Scholz Signed-off-by: Sebastian Siewior Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/isp1760-hcd.c | 44 ++++++++++++++++++++++++---------- drivers/usb/host/isp1760-hcd.h | 2 ++ 2 files changed, 33 insertions(+), 13 deletions(-) diff --git a/drivers/usb/host/isp1760-hcd.c b/drivers/usb/host/isp1760-hcd.c index db5f4f5c7a1..e209b3b709d 100644 --- a/drivers/usb/host/isp1760-hcd.c +++ b/drivers/usb/host/isp1760-hcd.c @@ -126,9 +126,8 @@ static void isp1760_writel(const unsigned int val, __u32 __iomem *regs) * doesn't quite work because some people have to enforce 32-bit access */ static void priv_read_copy(struct isp1760_hcd *priv, u32 *src, - __u32 __iomem *dst, u32 offset, u32 len) + __u32 __iomem *dst, u32 len) { - struct usb_hcd *hcd = priv_to_hcd(priv); u32 val; u8 *buff8; @@ -136,11 +135,6 @@ static void priv_read_copy(struct isp1760_hcd *priv, u32 *src, printk(KERN_ERR "ERROR: buffer: %p len: %d\n", src, len); return; } - isp1760_writel(offset, hcd->regs + HC_MEMORY_REG); - /* XXX - * 90nsec delay, the spec says something how this could be avoided. - */ - mdelay(1); while (len >= 4) { *src = __raw_readl(dst); @@ -987,8 +981,20 @@ static void do_atl_int(struct usb_hcd *usb_hcd) printk(KERN_ERR "qh is 0\n"); continue; } - priv_read_copy(priv, (u32 *)&ptd, usb_hcd->regs + atl_regs, - atl_regs, sizeof(ptd)); + isp1760_writel(atl_regs + ISP_BANK(0), usb_hcd->regs + + HC_MEMORY_REG); + isp1760_writel(payload + ISP_BANK(1), usb_hcd->regs + + HC_MEMORY_REG); + /* + * write bank1 address twice to ensure the 90ns delay (time + * between BANK0 write and the priv_read_copy() call is at + * least 3*t_WHWL + 2*t_w11 = 3*25ns + 2*17ns = 92ns) + */ + isp1760_writel(payload + ISP_BANK(1), usb_hcd->regs + + HC_MEMORY_REG); + + priv_read_copy(priv, (u32 *)&ptd, usb_hcd->regs + atl_regs + + ISP_BANK(0), sizeof(ptd)); dw1 = le32_to_cpu(ptd.dw1); dw2 = le32_to_cpu(ptd.dw2); @@ -1091,7 +1097,7 @@ static void do_atl_int(struct usb_hcd *usb_hcd) case IN_PID: priv_read_copy(priv, priv->atl_ints[queue_entry].data_buffer, - usb_hcd->regs + payload, payload, + usb_hcd->regs + payload + ISP_BANK(1), length); case OUT_PID: @@ -1206,8 +1212,20 @@ static void do_intl_int(struct usb_hcd *usb_hcd) continue; } - priv_read_copy(priv, (u32 *)&ptd, usb_hcd->regs + int_regs, - int_regs, sizeof(ptd)); + isp1760_writel(int_regs + ISP_BANK(0), usb_hcd->regs + + HC_MEMORY_REG); + isp1760_writel(payload + ISP_BANK(1), usb_hcd->regs + + HC_MEMORY_REG); + /* + * write bank1 address twice to ensure the 90ns delay (time + * between BANK0 write and the priv_read_copy() call is at + * least 3*t_WHWL + 2*t_w11 = 3*25ns + 2*17ns = 92ns) + */ + isp1760_writel(payload + ISP_BANK(1), usb_hcd->regs + + HC_MEMORY_REG); + + priv_read_copy(priv, (u32 *)&ptd, usb_hcd->regs + int_regs + + ISP_BANK(0), sizeof(ptd)); dw1 = le32_to_cpu(ptd.dw1); dw3 = le32_to_cpu(ptd.dw3); check_int_err_status(le32_to_cpu(ptd.dw4)); @@ -1242,7 +1260,7 @@ static void do_intl_int(struct usb_hcd *usb_hcd) case IN_PID: priv_read_copy(priv, priv->int_ints[queue_entry].data_buffer, - usb_hcd->regs + payload , payload, + usb_hcd->regs + payload + ISP_BANK(1), length); case OUT_PID: diff --git a/drivers/usb/host/isp1760-hcd.h b/drivers/usb/host/isp1760-hcd.h index 6473dd86993..3c61cd51cbb 100644 --- a/drivers/usb/host/isp1760-hcd.h +++ b/drivers/usb/host/isp1760-hcd.h @@ -54,6 +54,8 @@ void deinit_kmem_cache(void); #define BUFFER_MAP 0x7 #define HC_MEMORY_REG 0x33c +#define ISP_BANK(x) ((x) << 16) + #define HC_PORT1_CTRL 0x374 #define PORT1_POWER (3 << 3) #define PORT1_INIT1 (1 << 7) -- GitLab From 7839b5162d7d6c100f70a036be1e1f2b072857bc Mon Sep 17 00:00:00 2001 From: Sebastian Siewior Date: Thu, 17 Jul 2008 20:09:29 +0200 Subject: [PATCH 299/750] usb: isp1760: don't be noisy about short packets. According to Alan Stern, short packets are quite normal under certain circumstances. This printk was triggered by usb to serial converters on every packet and some usb sticks triggered a few of those while plugging the stick. This printks are now hidden unless USB debug mode is activated. Cc: Alan Stern Signed-off-by: Sebastian Siewior Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/isp1760-hcd.c | 6 +++--- drivers/usb/host/isp1760-hcd.h | 3 +++ 2 files changed, 6 insertions(+), 3 deletions(-) diff --git a/drivers/usb/host/isp1760-hcd.c b/drivers/usb/host/isp1760-hcd.c index e209b3b709d..d22a84f86a3 100644 --- a/drivers/usb/host/isp1760-hcd.c +++ b/drivers/usb/host/isp1760-hcd.c @@ -1128,11 +1128,11 @@ static void do_atl_int(struct usb_hcd *usb_hcd) } else if (usb_pipebulk(urb->pipe) && (length < qtd->length)) { /* short BULK received */ - printk(KERN_ERR "short bulk, %d instead %zu\n", length, - qtd->length); if (urb->transfer_flags & URB_SHORT_NOT_OK) { urb->status = -EREMOTEIO; - printk(KERN_ERR "not okey\n"); + isp1760_dbg(priv, "short bulk, %d instead %zu " + "with URB_SHORT_NOT_OK flag.\n", + length, qtd->length); } if (urb->status == -EINPROGRESS) diff --git a/drivers/usb/host/isp1760-hcd.h b/drivers/usb/host/isp1760-hcd.h index 3c61cd51cbb..4377277667d 100644 --- a/drivers/usb/host/isp1760-hcd.h +++ b/drivers/usb/host/isp1760-hcd.h @@ -121,6 +121,9 @@ struct inter_packet_info { typedef void (packet_enqueue)(struct usb_hcd *hcd, struct isp1760_qh *qh, struct isp1760_qtd *qtd); +#define isp1760_dbg(priv, fmt, args...) \ + dev_dbg(priv_to_hcd(priv)->self.controller, fmt, ##args) + #define isp1760_info(priv, fmt, args...) \ dev_info(priv_to_hcd(priv)->self.controller, fmt, ##args) -- GitLab From a5f6239949de78a9f33120d76f084928cb234a15 Mon Sep 17 00:00:00 2001 From: Lex Ross Date: Wed, 6 Aug 2008 16:25:08 +0400 Subject: [PATCH 300/750] USB: ftdi_sio: add support for PHI Fisco data cable (FT232BM based, VID/PID 0403:e40b) Support for PHI Fisco USB to Serial data cable (FTDI FT232BM based). PHI Fisco cable is supplied for connecting Philips Xenium 9@9++ mobile phones. PIDs were missing. Tested successfully with PHI Fisco Data Cable (VID/PID 0403:e40b) Signed-off-by: Lex V. Ross Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 1 + drivers/usb/serial/ftdi_sio.h | 1 + 2 files changed, 2 insertions(+) diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 54407351d7e..984f6eff4c4 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -638,6 +638,7 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(ELEKTOR_VID, ELEKTOR_FT323R_PID) }, { USB_DEVICE(TELLDUS_VID, TELLDUS_TELLSTICK_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MAXSTREAM_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_PHI_FISCO_PID) }, { USB_DEVICE(TML_VID, TML_USB_SERIAL_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ELSTER_UNICOM_PID) }, { USB_DEVICE(FTDI_VID, FTDI_PROPOX_JTAGCABLEII_PID) }, diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h index 7ca2ad0157f..382265bba96 100644 --- a/drivers/usb/serial/ftdi_sio.h +++ b/drivers/usb/serial/ftdi_sio.h @@ -526,6 +526,7 @@ #define FTDI_ELV_WS500_PID 0xE0E9 /* PC-Wetterstation (WS 500) */ #define FTDI_ELV_HS485_PID 0xE0EA /* USB to RS-485 adapter */ #define FTDI_ELV_EM1010PC_PID 0xE0EF /* Engery monitor EM 1010 PC */ +#define FTDI_PHI_FISCO_PID 0xE40B /* PHI Fisco USB to Serial cable */ /* * Definitions for ID TECH (www.idt-net.com) devices -- GitLab From bf3fc82895f4f501da9daef44d057749fe900c3e Mon Sep 17 00:00:00 2001 From: Leon Leong Date: Fri, 1 Aug 2008 11:40:12 +0800 Subject: [PATCH 301/750] USB: BandRich BandLuxe C150/C250 HSPA Data Card Driver This patch adds the Product ID for the BandLuxe C150/C250 3.5G data card series from BandRich Inc. After detection, the data card works fine. It was patched against kernel 2.6.27-rc1 with -mm patch Signed-off-by: Leon Leong Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 32 ++++++++++++++++++++++++++++++++ 1 file changed, 32 insertions(+) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index e4eca95f2b0..e7753ccaf70 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -186,6 +186,23 @@ static int option_send_setup(struct tty_struct *tty, struct usb_serial_port *po #define BANDRICH_VENDOR_ID 0x1A8D #define BANDRICH_PRODUCT_C100_1 0x1002 #define BANDRICH_PRODUCT_C100_2 0x1003 +#define BANDRICH_PRODUCT_1004 0x1004 +#define BANDRICH_PRODUCT_1005 0x1005 +#define BANDRICH_PRODUCT_1006 0x1006 +#define BANDRICH_PRODUCT_1007 0x1007 +#define BANDRICH_PRODUCT_1008 0x1008 +#define BANDRICH_PRODUCT_1009 0x1009 +#define BANDRICH_PRODUCT_100A 0x100a + +#define BANDRICH_PRODUCT_100B 0x100b +#define BANDRICH_PRODUCT_100C 0x100c +#define BANDRICH_PRODUCT_100D 0x100d +#define BANDRICH_PRODUCT_100E 0x100e + +#define BANDRICH_PRODUCT_100F 0x100f +#define BANDRICH_PRODUCT_1010 0x1010 +#define BANDRICH_PRODUCT_1011 0x1011 +#define BANDRICH_PRODUCT_1012 0x1012 #define AMOI_VENDOR_ID 0x1614 #define AMOI_PRODUCT_9508 0x0800 @@ -302,6 +319,21 @@ static struct usb_device_id option_ids[] = { { USB_DEVICE(ONDA_VENDOR_ID, ONDA_PRODUCT_ET502HS) }, { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_C100_1) }, { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_C100_2) }, + { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_1004) }, + { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_1005) }, + { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_1006) }, + { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_1007) }, + { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_1008) }, + { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_1009) }, + { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_100A) }, + { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_100B) }, + { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_100C) }, + { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_100D) }, + { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_100E) }, + { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_100F) }, + { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_1010) }, + { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_1011) }, + { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_1012) }, { USB_DEVICE(KYOCERA_VENDOR_ID, KYOCERA_PRODUCT_KPC650) }, { USB_DEVICE(KYOCERA_VENDOR_ID, KYOCERA_PRODUCT_KPC680) }, { USB_DEVICE(QUALCOMM_VENDOR_ID, 0x6000)}, /* ZTE AC8700 */ -- GitLab From 81eb8adfcec210a820ad9872ffb242482c976b8d Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Thu, 31 Jul 2008 19:06:13 +0200 Subject: [PATCH 302/750] USB: cdc-acm.c: Fix compile warnings The irq flags should be unsigned long. CC [M] drivers/usb/class/cdc-acm.o drivers/usb/class/cdc-acm.c: In function 'acm_waker': drivers/usb/class/cdc-acm.c:527: warning: comparison of distinct pointer types lacks a cast drivers/usb/class/cdc-acm.c:529: warning: comparison of distinct pointer types lacks a cast Signed-off-by: Takashi Iwai Signed-off-by: Greg Kroah-Hartman --- drivers/usb/class/cdc-acm.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index 0725b1871f2..a92395bf5f5 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -512,7 +512,7 @@ static void acm_softint(struct work_struct *work) static void acm_waker(struct work_struct *waker) { struct acm *acm = container_of(waker, struct acm, waker); - long flags; + unsigned long flags; int rv; rv = usb_autopm_get_interface(acm->control); -- GitLab From d28525f8866244a77b677c0470d4859cb2b6c2a8 Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Thu, 7 Aug 2008 13:02:40 -0400 Subject: [PATCH 303/750] usb-storage: unusual_devs entry for Nokia 5300 This patch (as1120) adds an unusual_devs entry for the Nokia 5300. Maybe once Nokia releases the Symbian code we'll be able to fix all the problems it has with the USB mass-storage protocol. Signed-off-by: Alan Stern Tested-by: Cedric Godin Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/unusual_devs.h | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h index 564999c42d7..ba412e68d47 100644 --- a/drivers/usb/storage/unusual_devs.h +++ b/drivers/usb/storage/unusual_devs.h @@ -225,6 +225,13 @@ UNUSUAL_DEV( 0x0421, 0x0495, 0x0370, 0x0370, US_SC_DEVICE, US_PR_DEVICE, NULL, US_FL_MAX_SECTORS_64 ), +/* Reported by Cedric Godin */ +UNUSUAL_DEV( 0x0421, 0x04b9, 0x0551, 0x0551, + "Nokia", + "5300", + US_SC_DEVICE, US_PR_DEVICE, NULL, + US_FL_FIX_CAPACITY ), + /* Reported by Olaf Hering from novell bug #105878 */ UNUSUAL_DEV( 0x0424, 0x0fdc, 0x0210, 0x0210, "SMSC", -- GitLab From 9ff78433f0aeb1f731a22a90206b685df4eaf52e Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Thu, 7 Aug 2008 13:04:51 -0400 Subject: [PATCH 304/750] USB: fix compiler warning fix This patch (as1123b) fixes a compiler warning: do_unbind_rebind() is defined but not used if CONFIG_PM=n. Problem originally found and initial patch submitted by Alexander Beregalov . Signed-off-by: Alan Stern Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/driver.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c index 6618bc89eb6..2be37fe466f 100644 --- a/drivers/usb/core/driver.c +++ b/drivers/usb/core/driver.c @@ -774,8 +774,6 @@ void usb_deregister(struct usb_driver *driver) } EXPORT_SYMBOL_GPL(usb_deregister); -#ifdef CONFIG_PM - /* Forced unbinding of a USB interface driver, either because * it doesn't support pre_reset/post_reset/reset_resume or * because it doesn't support suspend/resume. @@ -822,6 +820,8 @@ void usb_rebind_intf(struct usb_interface *intf) dev_warn(&intf->dev, "rebind failed: %d\n", rc); } +#ifdef CONFIG_PM + #define DO_UNBIND 0 #define DO_REBIND 1 -- GitLab From cbbcb9b0c7e4d1fd90cf54427382dae525773dc2 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Thu, 7 Aug 2008 16:29:24 +0400 Subject: [PATCH 305/750] USB: isp1301: fix compilation Signed-off-by: Dmitry Baryshkov Acked-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/i2c/chips/isp1301_omap.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/i2c/chips/isp1301_omap.c b/drivers/i2c/chips/isp1301_omap.c index 18355ae2155..4655b794ebe 100644 --- a/drivers/i2c/chips/isp1301_omap.c +++ b/drivers/i2c/chips/isp1301_omap.c @@ -1593,7 +1593,7 @@ fail1: if (machine_is_omap_h2()) { /* full speed signaling by default */ isp1301_set_bits(isp, ISP1301_MODE_CONTROL_1, - MC1_SPEED_REG); + MC1_SPEED); isp1301_set_bits(isp, ISP1301_MODE_CONTROL_2, MC2_SPD_SUSP_CTRL); -- GitLab From 54d0be9e3af1e20c3d0c3cc3eba50d33da24229c Mon Sep 17 00:00:00 2001 From: Yoshihiro Shimoda Date: Fri, 11 Jul 2008 18:53:45 +0900 Subject: [PATCH 306/750] USB: sh: r8a66597-hcd: fix disconnect regression fix the regression in commit 29fab0cd897519be9009ba8c898410ab83b378e9 that this driver executed reconnection processing when disconnected some devices. Signed-off-by: Yoshihiro Shimoda Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/r8a66597-hcd.c | 49 +++++++++++++++++---------------- 1 file changed, 26 insertions(+), 23 deletions(-) diff --git a/drivers/usb/host/r8a66597-hcd.c b/drivers/usb/host/r8a66597-hcd.c index d5f02dddb12..ea7126f99ca 100644 --- a/drivers/usb/host/r8a66597-hcd.c +++ b/drivers/usb/host/r8a66597-hcd.c @@ -964,11 +964,34 @@ static void pipe_irq_disable(struct r8a66597 *r8a66597, u16 pipenum) disable_irq_nrdy(r8a66597, pipenum); } +static void r8a66597_root_hub_start_polling(struct r8a66597 *r8a66597) +{ + mod_timer(&r8a66597->rh_timer, + jiffies + msecs_to_jiffies(R8A66597_RH_POLL_TIME)); +} + +static void start_root_hub_sampling(struct r8a66597 *r8a66597, int port, + int connect) +{ + struct r8a66597_root_hub *rh = &r8a66597->root_hub[port]; + + rh->old_syssts = r8a66597_read(r8a66597, get_syssts_reg(port)) & LNST; + rh->scount = R8A66597_MAX_SAMPLING; + if (connect) + rh->port |= 1 << USB_PORT_FEAT_CONNECTION; + else + rh->port &= ~(1 << USB_PORT_FEAT_CONNECTION); + rh->port |= 1 << USB_PORT_FEAT_C_CONNECTION; + + r8a66597_root_hub_start_polling(r8a66597); +} + /* this function must be called with interrupt disabled */ static void r8a66597_check_syssts(struct r8a66597 *r8a66597, int port, u16 syssts) { if (syssts == SE0) { + r8a66597_write(r8a66597, ~ATTCH, get_intsts_reg(port)); r8a66597_bset(r8a66597, ATTCHE, get_intenb_reg(port)); return; } @@ -1002,13 +1025,10 @@ static void r8a66597_usb_disconnect(struct r8a66597 *r8a66597, int port) { struct r8a66597_device *dev = r8a66597->root_hub[port].dev; - r8a66597->root_hub[port].port &= ~(1 << USB_PORT_FEAT_CONNECTION); - r8a66597->root_hub[port].port |= (1 << USB_PORT_FEAT_C_CONNECTION); - disable_r8a66597_pipe_all(r8a66597, dev); free_usb_address(r8a66597, dev); - r8a66597_bset(r8a66597, ATTCHE, get_intenb_reg(port)); + start_root_hub_sampling(r8a66597, port, 0); } /* this function must be called with interrupt disabled */ @@ -1551,23 +1571,6 @@ static void irq_pipe_nrdy(struct r8a66597 *r8a66597) } } -static void r8a66597_root_hub_start_polling(struct r8a66597 *r8a66597) -{ - mod_timer(&r8a66597->rh_timer, - jiffies + msecs_to_jiffies(R8A66597_RH_POLL_TIME)); -} - -static void start_root_hub_sampling(struct r8a66597 *r8a66597, int port) -{ - struct r8a66597_root_hub *rh = &r8a66597->root_hub[port]; - - rh->old_syssts = r8a66597_read(r8a66597, get_syssts_reg(port)) & LNST; - rh->scount = R8A66597_MAX_SAMPLING; - r8a66597->root_hub[port].port |= (1 << USB_PORT_FEAT_CONNECTION) - | (1 << USB_PORT_FEAT_C_CONNECTION); - r8a66597_root_hub_start_polling(r8a66597); -} - static irqreturn_t r8a66597_irq(struct usb_hcd *hcd) { struct r8a66597 *r8a66597 = hcd_to_r8a66597(hcd); @@ -1594,7 +1597,7 @@ static irqreturn_t r8a66597_irq(struct usb_hcd *hcd) r8a66597_bclr(r8a66597, ATTCHE, INTENB2); /* start usb bus sampling */ - start_root_hub_sampling(r8a66597, 1); + start_root_hub_sampling(r8a66597, 1, 1); } if (mask2 & DTCH) { r8a66597_write(r8a66597, ~DTCH, INTSTS2); @@ -1609,7 +1612,7 @@ static irqreturn_t r8a66597_irq(struct usb_hcd *hcd) r8a66597_bclr(r8a66597, ATTCHE, INTENB1); /* start usb bus sampling */ - start_root_hub_sampling(r8a66597, 0); + start_root_hub_sampling(r8a66597, 0, 1); } if (mask1 & DTCH) { r8a66597_write(r8a66597, ~DTCH, INTSTS1); -- GitLab From 630c7aa80152881980e45c11584f22476f71959b Mon Sep 17 00:00:00 2001 From: David Brownell Date: Wed, 6 Aug 2008 18:48:52 -0700 Subject: [PATCH 307/750] usb gadget: remove needless struct members This removes some unused members from the various USB functions. Signed-off-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/f_acm.c | 2 -- drivers/usb/gadget/f_ecm.c | 2 -- drivers/usb/gadget/f_rndis.c | 2 -- drivers/usb/gadget/f_serial.c | 2 -- drivers/usb/gadget/f_subset.c | 2 -- 5 files changed, 10 deletions(-) diff --git a/drivers/usb/gadget/f_acm.c b/drivers/usb/gadget/f_acm.c index d8faccf2789..f3bf5612af2 100644 --- a/drivers/usb/gadget/f_acm.c +++ b/drivers/usb/gadget/f_acm.c @@ -47,9 +47,7 @@ struct f_acm { u8 ctrl_id, data_id; u8 port_num; - struct usb_descriptor_header **fs_function; struct acm_ep_descs fs; - struct usb_descriptor_header **hs_function; struct acm_ep_descs hs; struct usb_ep *notify; diff --git a/drivers/usb/gadget/f_ecm.c b/drivers/usb/gadget/f_ecm.c index 0822e9d7693..a2b5c092bda 100644 --- a/drivers/usb/gadget/f_ecm.c +++ b/drivers/usb/gadget/f_ecm.c @@ -63,9 +63,7 @@ struct f_ecm { char ethaddr[14]; - struct usb_descriptor_header **fs_function; struct ecm_ep_descs fs; - struct usb_descriptor_header **hs_function; struct ecm_ep_descs hs; struct usb_ep *notify; diff --git a/drivers/usb/gadget/f_rndis.c b/drivers/usb/gadget/f_rndis.c index 61652f0f13f..659b3d9671c 100644 --- a/drivers/usb/gadget/f_rndis.c +++ b/drivers/usb/gadget/f_rndis.c @@ -85,9 +85,7 @@ struct f_rndis { u8 ethaddr[ETH_ALEN]; int config; - struct usb_descriptor_header **fs_function; struct rndis_ep_descs fs; - struct usb_descriptor_header **hs_function; struct rndis_ep_descs hs; struct usb_ep *notify; diff --git a/drivers/usb/gadget/f_serial.c b/drivers/usb/gadget/f_serial.c index 1b6bde9aaed..fe5674db344 100644 --- a/drivers/usb/gadget/f_serial.c +++ b/drivers/usb/gadget/f_serial.c @@ -36,9 +36,7 @@ struct f_gser { u8 data_id; u8 port_num; - struct usb_descriptor_header **fs_function; struct gser_descs fs; - struct usb_descriptor_header **hs_function; struct gser_descs hs; }; diff --git a/drivers/usb/gadget/f_subset.c b/drivers/usb/gadget/f_subset.c index afeab9a0523..acb8d233aa1 100644 --- a/drivers/usb/gadget/f_subset.c +++ b/drivers/usb/gadget/f_subset.c @@ -66,9 +66,7 @@ struct f_gether { char ethaddr[14]; - struct usb_descriptor_header **fs_function; struct geth_descs fs; - struct usb_descriptor_header **hs_function; struct geth_descs hs; }; -- GitLab From 1f1ba11b64947051fc32aa15fcccef6463b433f7 Mon Sep 17 00:00:00 2001 From: David Brownell Date: Wed, 6 Aug 2008 18:49:57 -0700 Subject: [PATCH 308/750] usb gadget: issue notifications from ACM function Update the CDC-ACM gadget code to support the peripheral-to-host notifications when the tty is opened or closed, or issues a BREAK. The serial framework code calls new generic hooks; right now only CDC-ACM uses those hooks. This resolves several REVISIT comments in the code. (Based on a patch from Felipe Balbi.) Note that this doesn't expose USB_CDC_CAP_BRK to the host, since this code still rejects USB_CDC_REQ_SEND_BREAK control requests for host-to-peripheral BREAK signaling (received via /dev/ttyGS*). Signed-off-by: David Brownell Cc: Felipe Balbi Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/f_acm.c | 194 ++++++++++++++++++++++++++++++++-- drivers/usb/gadget/u_serial.c | 56 +++++++--- drivers/usb/gadget/u_serial.h | 12 ++- 3 files changed, 235 insertions(+), 27 deletions(-) diff --git a/drivers/usb/gadget/f_acm.c b/drivers/usb/gadget/f_acm.c index f3bf5612af2..5ee1590b8e9 100644 --- a/drivers/usb/gadget/f_acm.c +++ b/drivers/usb/gadget/f_acm.c @@ -47,16 +47,37 @@ struct f_acm { u8 ctrl_id, data_id; u8 port_num; + u8 pending; + + /* lock is mostly for pending and notify_req ... they get accessed + * by callbacks both from tty (open/close/break) under its spinlock, + * and notify_req.complete() which can't use that lock. + */ + spinlock_t lock; + struct acm_ep_descs fs; struct acm_ep_descs hs; struct usb_ep *notify; struct usb_endpoint_descriptor *notify_desc; + struct usb_request *notify_req; struct usb_cdc_line_coding port_line_coding; /* 8-N-1 etc */ + + /* SetControlLineState request -- CDC 1.1 section 6.2.14 (INPUT) */ u16 port_handshake_bits; -#define RS232_RTS (1 << 1) /* unused with full duplex */ -#define RS232_DTR (1 << 0) /* host is ready for data r/w */ +#define ACM_CTRL_RTS (1 << 1) /* unused with full duplex */ +#define ACM_CTRL_DTR (1 << 0) /* host is ready for data r/w */ + + /* SerialState notification -- CDC 1.1 section 6.3.5 (OUTPUT) */ + u16 serial_state; +#define ACM_CTRL_OVERRUN (1 << 6) +#define ACM_CTRL_PARITY (1 << 5) +#define ACM_CTRL_FRAMING (1 << 4) +#define ACM_CTRL_RI (1 << 3) +#define ACM_CTRL_BRK (1 << 2) +#define ACM_CTRL_DSR (1 << 1) +#define ACM_CTRL_DCD (1 << 0) }; static inline struct f_acm *func_to_acm(struct usb_function *f) @@ -64,12 +85,17 @@ static inline struct f_acm *func_to_acm(struct usb_function *f) return container_of(f, struct f_acm, port.func); } +static inline struct f_acm *port_to_acm(struct gserial *p) +{ + return container_of(p, struct f_acm, port); +} + /*-------------------------------------------------------------------------*/ /* notification endpoint uses smallish and infrequent fixed-size messages */ #define GS_LOG2_NOTIFY_INTERVAL 5 /* 1 << 5 == 32 msec */ -#define GS_NOTIFY_MAXPACKET 8 +#define GS_NOTIFY_MAXPACKET 10 /* notification + 2 bytes */ /* interface and class descriptors: */ @@ -115,7 +141,7 @@ static struct usb_cdc_acm_descriptor acm_descriptor __initdata = { .bLength = sizeof(acm_descriptor), .bDescriptorType = USB_DT_CS_INTERFACE, .bDescriptorSubType = USB_CDC_ACM_TYPE, - .bmCapabilities = (1 << 1), + .bmCapabilities = USB_CDC_CAP_LINE, }; static struct usb_cdc_union_desc acm_union_desc __initdata = { @@ -275,6 +301,11 @@ static int acm_setup(struct usb_function *f, const struct usb_ctrlrequest *ctrl) /* composite driver infrastructure handles everything except * CDC class messages; interface activation uses set_alt(). + * + * Note CDC spec table 4 lists the ACM request profile. It requires + * encapsulated command support ... we don't handle any, and respond + * to them by stalling. Options include get/set/clear comm features + * (not that useful) and SEND_BREAK. */ switch ((ctrl->bRequestType << 8) | ctrl->bRequest) { @@ -310,7 +341,7 @@ static int acm_setup(struct usb_function *f, const struct usb_ctrlrequest *ctrl) value = 0; /* FIXME we should not allow data to flow until the - * host sets the RS232_DTR bit; and when it clears + * host sets the ACM_CTRL_DTR bit; and when it clears * that bit, we should return to that no-flow state. */ acm->port_handshake_bits = w_value; @@ -348,9 +379,6 @@ static int acm_set_alt(struct usb_function *f, unsigned intf, unsigned alt) /* we know alt == 0, so this is an activation or a reset */ if (intf == acm->ctrl_id) { - /* REVISIT this may need more work when we start to - * send notifications ... - */ if (acm->notify->driver_data) { VDBG(cdev, "reset acm control interface %d\n", intf); usb_ep_disable(acm->notify); @@ -395,6 +423,128 @@ static void acm_disable(struct usb_function *f) /*-------------------------------------------------------------------------*/ +/** + * acm_cdc_notify - issue CDC notification to host + * @acm: wraps host to be notified + * @type: notification type + * @value: Refer to cdc specs, wValue field. + * @data: data to be sent + * @length: size of data + * Context: irqs blocked, acm->lock held, acm_notify_req non-null + * + * Returns zero on sucess or a negative errno. + * + * See section 6.3.5 of the CDC 1.1 specification for information + * about the only notification we issue: SerialState change. + */ +static int acm_cdc_notify(struct f_acm *acm, u8 type, u16 value, + void *data, unsigned length) +{ + struct usb_ep *ep = acm->notify; + struct usb_request *req; + struct usb_cdc_notification *notify; + const unsigned len = sizeof(*notify) + length; + void *buf; + int status; + + req = acm->notify_req; + acm->notify_req = NULL; + acm->pending = false; + + req->length = len; + notify = req->buf; + buf = notify + 1; + + notify->bmRequestType = USB_DIR_IN | USB_TYPE_CLASS + | USB_RECIP_INTERFACE; + notify->bNotificationType = type; + notify->wValue = cpu_to_le16(value); + notify->wIndex = cpu_to_le16(acm->ctrl_id); + notify->wLength = cpu_to_le16(length); + memcpy(buf, data, length); + + status = usb_ep_queue(ep, req, GFP_ATOMIC); + if (status < 0) { + ERROR(acm->port.func.config->cdev, + "acm ttyGS%d can't notify serial state, %d\n", + acm->port_num, status); + acm->notify_req = req; + } + + return status; +} + +static int acm_notify_serial_state(struct f_acm *acm) +{ + struct usb_composite_dev *cdev = acm->port.func.config->cdev; + int status; + + spin_lock(&acm->lock); + if (acm->notify_req) { + DBG(cdev, "acm ttyGS%d serial state %04x\n", + acm->port_num, acm->serial_state); + status = acm_cdc_notify(acm, USB_CDC_NOTIFY_SERIAL_STATE, + 0, &acm->serial_state, sizeof(acm->serial_state)); + } else { + acm->pending = true; + status = 0; + } + spin_unlock(&acm->lock); + return status; +} + +static void acm_cdc_notify_complete(struct usb_ep *ep, struct usb_request *req) +{ + struct f_acm *acm = req->context; + u8 doit = false; + + /* on this call path we do NOT hold the port spinlock, + * which is why ACM needs its own spinlock + */ + spin_lock(&acm->lock); + if (req->status != -ESHUTDOWN) + doit = acm->pending; + acm->notify_req = req; + spin_unlock(&acm->lock); + + if (doit) + acm_notify_serial_state(acm); +} + +/* connect == the TTY link is open */ + +static void acm_connect(struct gserial *port) +{ + struct f_acm *acm = port_to_acm(port); + + acm->serial_state |= ACM_CTRL_DSR | ACM_CTRL_DCD; + acm_notify_serial_state(acm); +} + +static void acm_disconnect(struct gserial *port) +{ + struct f_acm *acm = port_to_acm(port); + + acm->serial_state &= ~(ACM_CTRL_DSR | ACM_CTRL_DCD); + acm_notify_serial_state(acm); +} + +static int acm_send_break(struct gserial *port, int duration) +{ + struct f_acm *acm = port_to_acm(port); + u16 state; + + state = acm->serial_state; + state &= ~ACM_CTRL_BRK; + if (duration) + state |= ACM_CTRL_BRK; + + acm->serial_state = state; + return acm_notify_serial_state(acm); +} + +/*-------------------------------------------------------------------------*/ + /* ACM function driver setup/binding */ static int __init acm_bind(struct usb_configuration *c, struct usb_function *f) @@ -443,8 +593,20 @@ acm_bind(struct usb_configuration *c, struct usb_function *f) acm->notify = ep; ep->driver_data = cdev; /* claim */ + /* allocate notification */ + acm->notify_req = gs_alloc_req(ep, + sizeof(struct usb_cdc_notification) + 2, + GFP_KERNEL); + if (!acm->notify_req) + goto fail; + + acm->notify_req->complete = acm_cdc_notify_complete; + acm->notify_req->context = acm; + /* copy descriptors, and track endpoint copies */ f->descriptors = usb_copy_descriptors(acm_fs_function); + if (!f->descriptors) + goto fail; acm->fs.in = usb_find_endpoint(acm_fs_function, f->descriptors, &acm_fs_in_desc); @@ -476,8 +638,6 @@ acm_bind(struct usb_configuration *c, struct usb_function *f) f->hs_descriptors, &acm_hs_notify_desc); } - /* FIXME provide a callback for triggering notifications */ - DBG(cdev, "acm ttyGS%d: %s speed IN/%s OUT/%s NOTIFY/%s\n", acm->port_num, gadget_is_dualspeed(c->cdev->gadget) ? "dual" : "full", @@ -486,6 +646,9 @@ acm_bind(struct usb_configuration *c, struct usb_function *f) return 0; fail: + if (acm->notify_req) + gs_free_req(acm->notify, acm->notify_req); + /* we might as well release our claims on endpoints */ if (acm->notify) acm->notify->driver_data = NULL; @@ -502,10 +665,13 @@ fail: static void acm_unbind(struct usb_configuration *c, struct usb_function *f) { + struct f_acm *acm = func_to_acm(f); + if (gadget_is_dualspeed(c->cdev->gadget)) usb_free_descriptors(f->hs_descriptors); usb_free_descriptors(f->descriptors); - kfree(func_to_acm(f)); + gs_free_req(acm->notify, acm->notify_req); + kfree(acm); } /* Some controllers can't support CDC ACM ... */ @@ -569,8 +735,14 @@ int __init acm_bind_config(struct usb_configuration *c, u8 port_num) if (!acm) return -ENOMEM; + spin_lock_init(&acm->lock); + acm->port_num = port_num; + acm->port.connect = acm_connect; + acm->port.disconnect = acm_disconnect; + acm->port.send_break = acm_send_break; + acm->port.func.name = "acm"; acm->port.func.strings = acm_strings; /* descriptors are per-instance copies */ diff --git a/drivers/usb/gadget/u_serial.c b/drivers/usb/gadget/u_serial.c index 6641efa5563..53d59287f2b 100644 --- a/drivers/usb/gadget/u_serial.c +++ b/drivers/usb/gadget/u_serial.c @@ -60,7 +60,8 @@ * tty_struct links to the tty/filesystem framework * * gserial <---> gs_port ... links will be null when the USB link is - * inactive; managed by gserial_{connect,disconnect}(). + * inactive; managed by gserial_{connect,disconnect}(). each gserial + * instance can wrap its own USB control protocol. * gserial->ioport == usb_ep->driver_data ... gs_port * gs_port->port_usb ... gserial * @@ -181,7 +182,7 @@ static void gs_buf_clear(struct gs_buf *gb) /* * gs_buf_data_avail * - * Return the number of bytes of data available in the circular + * Return the number of bytes of data written into the circular * buffer. */ static unsigned gs_buf_data_avail(struct gs_buf *gb) @@ -282,7 +283,7 @@ gs_buf_get(struct gs_buf *gb, char *buf, unsigned count) * Allocate a usb_request and its buffer. Returns a pointer to the * usb_request or NULL if there is an error. */ -static struct usb_request * +struct usb_request * gs_alloc_req(struct usb_ep *ep, unsigned len, gfp_t kmalloc_flags) { struct usb_request *req; @@ -306,7 +307,7 @@ gs_alloc_req(struct usb_ep *ep, unsigned len, gfp_t kmalloc_flags) * * Free a usb_request and its buffer. */ -static void gs_free_req(struct usb_ep *ep, struct usb_request *req) +void gs_free_req(struct usb_ep *ep, struct usb_request *req) { kfree(req->buf); usb_ep_free_request(ep, req); @@ -788,10 +789,13 @@ static int gs_open(struct tty_struct *tty, struct file *file) /* if connected, start the I/O stream */ if (port->port_usb) { + struct gserial *gser = port->port_usb; + pr_debug("gs_open: start ttyGS%d\n", port->port_num); gs_start_io(port); - /* REVISIT for ACM, issue "network connected" event */ + if (gser->connect) + gser->connect(gser); } pr_debug("gs_open: ttyGS%d (%p,%p)\n", port->port_num, tty, file); @@ -818,6 +822,7 @@ static int gs_writes_finished(struct gs_port *p) static void gs_close(struct tty_struct *tty, struct file *file) { struct gs_port *port = tty->driver_data; + struct gserial *gser; spin_lock_irq(&port->port_lock); @@ -837,26 +842,27 @@ static void gs_close(struct tty_struct *tty, struct file *file) port->openclose = true; port->open_count = 0; - if (port->port_usb) - /* REVISIT for ACM, issue "network disconnected" event */; + gser = port->port_usb; + if (gser && gser->disconnect) + gser->disconnect(gser); /* wait for circular write buffer to drain, disconnect, or at * most GS_CLOSE_TIMEOUT seconds; then discard the rest */ - if (gs_buf_data_avail(&port->port_write_buf) > 0 - && port->port_usb) { + if (gs_buf_data_avail(&port->port_write_buf) > 0 && gser) { spin_unlock_irq(&port->port_lock); wait_event_interruptible_timeout(port->drain_wait, gs_writes_finished(port), GS_CLOSE_TIMEOUT * HZ); spin_lock_irq(&port->port_lock); + gser = port->port_usb; } /* Iff we're disconnected, there can be no I/O in flight so it's * ok to free the circular buffer; else just scrub it. And don't * let the push tasklet fire again until we're re-opened. */ - if (port->port_usb == NULL) + if (gser == NULL) gs_buf_free(&port->port_write_buf); else gs_buf_clear(&port->port_write_buf); @@ -974,6 +980,24 @@ static void gs_unthrottle(struct tty_struct *tty) spin_unlock_irqrestore(&port->port_lock, flags); } +static int gs_break_ctl(struct tty_struct *tty, int duration) +{ + struct gs_port *port = tty->driver_data; + int status = 0; + struct gserial *gser; + + pr_vdebug("gs_break_ctl: ttyGS%d, send break (%d) \n", + port->port_num, duration); + + spin_lock_irq(&port->port_lock); + gser = port->port_usb; + if (gser && gser->send_break) + status = gser->send_break(gser, duration); + spin_unlock_irq(&port->port_lock); + + return status; +} + static const struct tty_operations gs_tty_ops = { .open = gs_open, .close = gs_close, @@ -983,6 +1007,7 @@ static const struct tty_operations gs_tty_ops = { .write_room = gs_write_room, .chars_in_buffer = gs_chars_in_buffer, .unthrottle = gs_unthrottle, + .break_ctl = gs_break_ctl, }; /*-------------------------------------------------------------------------*/ @@ -1230,14 +1255,17 @@ int gserial_connect(struct gserial *gser, u8 port_num) /* REVISIT if waiting on "carrier detect", signal. */ - /* REVISIT for ACM, issue "network connection" status notification: - * connected if open_count, else disconnected. + /* if it's already open, start I/O ... and notify the serial + * protocol about open/close status (connect/disconnect). */ - - /* if it's already open, start I/O */ if (port->open_count) { pr_debug("gserial_connect: start ttyGS%d\n", port->port_num); gs_start_io(port); + if (gser->connect) + gser->connect(gser); + } else { + if (gser->disconnect) + gser->disconnect(gser); } spin_unlock_irqrestore(&port->port_lock, flags); diff --git a/drivers/usb/gadget/u_serial.h b/drivers/usb/gadget/u_serial.h index 7b561138f90..af3910d01ae 100644 --- a/drivers/usb/gadget/u_serial.h +++ b/drivers/usb/gadget/u_serial.h @@ -23,8 +23,7 @@ * style I/O using the USB peripheral endpoints listed here, including * hookups to sysfs and /dev for each logical "tty" device. * - * REVISIT need TTY --> USB event flow too, so ACM can report open/close - * as carrier detect events. Model after ECM. There's more ACM state too. + * REVISIT at least ACM could support tiocmget() if needed. * * REVISIT someday, allow multiplexing several TTYs over these endpoints. */ @@ -41,8 +40,17 @@ struct gserial { /* REVISIT avoid this CDC-ACM support harder ... */ struct usb_cdc_line_coding port_line_coding; /* 9600-8-N-1 etc */ + + /* notification callbacks */ + void (*connect)(struct gserial *p); + void (*disconnect)(struct gserial *p); + int (*send_break)(struct gserial *p, int duration); }; +/* utilities to allocate/free request and buffer */ +struct usb_request *gs_alloc_req(struct usb_ep *ep, unsigned len, gfp_t flags); +void gs_free_req(struct usb_ep *, struct usb_request *req); + /* port setup/teardown is handled by gadget driver */ int gserial_setup(struct usb_gadget *g, unsigned n_ports); void gserial_cleanup(void); -- GitLab From 672c4e1843c54227ff1bdf1fdd96f9c45c56aa85 Mon Sep 17 00:00:00 2001 From: David Brownell Date: Wed, 6 Aug 2008 18:41:12 -0700 Subject: [PATCH 309/750] usb: cdc-acm: bugfix release() Bugfixes to the usb_driver_release_interface() usage; (a) make sure releasing *either* interface first will release the other, instead of insisting it be the control interface; (b) remove the recently-added self-deadlock. (The "fix disconnect bug in cdc-acm" patch was incomplete and incorrect.) Plus a small "sparse" fix: rename a local variable so it doesn't shadow a function parameter. Signed-off-by: David Brownell Acked-by: Oliver Neukum Signed-off-by: Greg Kroah-Hartman --- drivers/usb/class/cdc-acm.c | 15 +++++++++------ 1 file changed, 9 insertions(+), 6 deletions(-) diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index a92395bf5f5..910247d191e 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -1108,9 +1108,11 @@ skip_normal_probe: rcv->instance = acm; } for (i = 0; i < num_rx_buf; i++) { - struct acm_rb *buf = &(acm->rb[i]); + struct acm_rb *rb = &(acm->rb[i]); - if (!(buf->base = usb_buffer_alloc(acm->dev, readsize, GFP_KERNEL, &buf->dma))) { + rb->base = usb_buffer_alloc(acm->dev, readsize, + GFP_KERNEL, &rb->dma); + if (!rb->base) { dev_dbg(&intf->dev, "out of memory (read bufs usb_buffer_alloc)\n"); goto alloc_fail7; } @@ -1172,6 +1174,7 @@ skip_countries: acm_set_line(acm, &acm->line); usb_driver_claim_interface(&acm_driver, data_interface, acm); + usb_set_intfdata(data_interface, acm); usb_get_intf(control_interface); tty_register_device(acm_tty_driver, minor, &control_interface->dev); @@ -1221,11 +1224,11 @@ static void acm_disconnect(struct usb_interface *intf) struct acm *acm = usb_get_intfdata(intf); struct usb_device *usb_dev = interface_to_usbdev(intf); - mutex_lock(&open_mutex); - if (!acm || !acm->dev) { - mutex_unlock(&open_mutex); + /* sibling interface is already cleaning up */ + if (!acm) return; - } + + mutex_lock(&open_mutex); if (acm->country_codes){ device_remove_file(&acm->control->dev, &dev_attr_wCountryCodes); -- GitLab From 934da4635c2d05cef474e5243ef05df95b2ad264 Mon Sep 17 00:00:00 2001 From: David Brownell Date: Wed, 6 Aug 2008 18:44:12 -0700 Subject: [PATCH 310/750] usb: cdc-acm: stop dropping tx buffers The "increase cdc-acm write throughput" patch left in place two now-obsolete mechanisms, either of which can make the cdc-acm driver drop TX data (nasty!). This patch removes them: - The write_ready flag ... if an URB and buffer were found, they can (and should!) always be used. - TX path acm_wb_is_used() ... used when the buffer was just allocated, so that check is pointless. Also fix a won't-yet-matter leak of a write buffer on a disconnect path. Signed-off-by: David Brownell Cc: David Engraf Acked-by: Oliver Neukum Signed-off-by: Greg Kroah-Hartman --- drivers/usb/class/cdc-acm.c | 32 +++----------------------------- drivers/usb/class/cdc-acm.h | 2 -- 2 files changed, 3 insertions(+), 31 deletions(-) diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index 910247d191e..a9dd28f446d 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -144,11 +144,6 @@ static int acm_wb_is_avail(struct acm *acm) return n; } -static inline int acm_wb_is_used(struct acm *acm, int wbn) -{ - return acm->wb[wbn].use; -} - /* * Finish write. */ @@ -157,7 +152,6 @@ static void acm_write_done(struct acm *acm, struct acm_wb *wb) unsigned long flags; spin_lock_irqsave(&acm->write_lock, flags); - acm->write_ready = 1; wb->use = 0; acm->transmitting--; spin_unlock_irqrestore(&acm->write_lock, flags); @@ -190,40 +184,25 @@ static int acm_start_wb(struct acm *acm, struct acm_wb *wb) static int acm_write_start(struct acm *acm, int wbn) { unsigned long flags; - struct acm_wb *wb; + struct acm_wb *wb = &acm->wb[wbn]; int rc; spin_lock_irqsave(&acm->write_lock, flags); if (!acm->dev) { + wb->use = 0; spin_unlock_irqrestore(&acm->write_lock, flags); return -ENODEV; } - if (!acm->write_ready) { - spin_unlock_irqrestore(&acm->write_lock, flags); - return 0; /* A white lie */ - } - - wb = &acm->wb[wbn]; - if(acm_wb_is_avail(acm) <= 1) - acm->write_ready = 0; - dbg("%s susp_count: %d", __func__, acm->susp_count); if (acm->susp_count) { - acm->old_ready = acm->write_ready; acm->delayed_wb = wb; - acm->write_ready = 0; schedule_work(&acm->waker); spin_unlock_irqrestore(&acm->write_lock, flags); return 0; /* A white lie */ } usb_mark_last_busy(acm->dev); - if (!acm_wb_is_used(acm, wbn)) { - spin_unlock_irqrestore(&acm->write_lock, flags); - return 0; - } - rc = acm_start_wb(acm, wb); spin_unlock_irqrestore(&acm->write_lock, flags); @@ -512,7 +491,6 @@ static void acm_softint(struct work_struct *work) static void acm_waker(struct work_struct *waker) { struct acm *acm = container_of(waker, struct acm, waker); - unsigned long flags; int rv; rv = usb_autopm_get_interface(acm->control); @@ -524,9 +502,6 @@ static void acm_waker(struct work_struct *waker) acm_start_wb(acm, acm->delayed_wb); acm->delayed_wb = NULL; } - spin_lock_irqsave(&acm->write_lock, flags); - acm->write_ready = acm->old_ready; - spin_unlock_irqrestore(&acm->write_lock, flags); usb_autopm_put_interface(acm->control); } @@ -697,7 +672,7 @@ static int acm_tty_write_room(struct tty_struct *tty) * Do not let the line discipline to know that we have a reserve, * or it might get too enthusiastic. */ - return (acm->write_ready && acm_wb_is_avail(acm)) ? acm->writesize : 0; + return acm_wb_is_avail(acm) ? acm->writesize : 0; } static int acm_tty_chars_in_buffer(struct tty_struct *tty) @@ -1076,7 +1051,6 @@ skip_normal_probe: spin_lock_init(&acm->write_lock); spin_lock_init(&acm->read_lock); mutex_init(&acm->mutex); - acm->write_ready = 1; acm->rx_endpoint = usb_rcvbulkpipe(usb_dev, epread->bEndpointAddress); buf = usb_buffer_alloc(usb_dev, ctrlsize, GFP_KERNEL, &acm->ctrl_dma); diff --git a/drivers/usb/class/cdc-acm.h b/drivers/usb/class/cdc-acm.h index 85c3aaaab7c..94266362ca6 100644 --- a/drivers/usb/class/cdc-acm.h +++ b/drivers/usb/class/cdc-acm.h @@ -106,8 +106,6 @@ struct acm { struct list_head spare_read_bufs; struct list_head filled_read_bufs; int write_used; /* number of non-empty write buffers */ - int write_ready; /* write urb is not running */ - int old_ready; int processing; int transmitting; spinlock_t write_lock; -- GitLab From e5fbab51b4219fbd1dab28666affe38a920b5f7e Mon Sep 17 00:00:00 2001 From: David Brownell Date: Wed, 6 Aug 2008 18:46:10 -0700 Subject: [PATCH 311/750] usb: cdc-acm: drain writes on close Add a mechanism to let the write queue drain naturally before closing the TTY, rather than always losing that data. There is a timeout, so it can't wait too long. Provide missing locking inside acm_wb_is_avail(); it matters more now. Note, this presumes an earlier patch was applied, removing a call to this routine where the lock was held. Slightly improved diagnostics on write URB completion, so we can tell when a write URB gets killed and, if so, how much data it wrote first ... and so that I/O path is normally silent (and can't much change timings). Signed-off-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/class/cdc-acm.c | 39 ++++++++++++++++++++++++++++++++----- drivers/usb/class/cdc-acm.h | 1 + 2 files changed, 35 insertions(+), 5 deletions(-) diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index a9dd28f446d..efc4373eded 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -51,6 +51,7 @@ */ #undef DEBUG +#undef VERBOSE_DEBUG #include #include @@ -70,6 +71,9 @@ #include "cdc-acm.h" + +#define ACM_CLOSE_TIMEOUT 15 /* seconds to let writes drain */ + /* * Version Information */ @@ -85,6 +89,12 @@ static DEFINE_MUTEX(open_mutex); #define ACM_READY(acm) (acm && acm->dev && acm->used) +#ifdef VERBOSE_DEBUG +#define verbose 1 +#else +#define verbose 0 +#endif + /* * Functions for ACM control messages. */ @@ -136,11 +146,14 @@ static int acm_wb_alloc(struct acm *acm) static int acm_wb_is_avail(struct acm *acm) { int i, n; + unsigned long flags; n = ACM_NW; + spin_lock_irqsave(&acm->write_lock, flags); for (i = 0; i < ACM_NW; i++) { n -= acm->wb[i].use; } + spin_unlock_irqrestore(&acm->write_lock, flags); return n; } @@ -467,22 +480,28 @@ urbs: /* data interface wrote those outgoing bytes */ static void acm_write_bulk(struct urb *urb) { - struct acm *acm; struct acm_wb *wb = urb->context; + struct acm *acm = wb->instance; - dbg("Entering acm_write_bulk with status %d", urb->status); + if (verbose || urb->status + || (urb->actual_length != urb->transfer_buffer_length)) + dev_dbg(&acm->data->dev, "tx %d/%d bytes -- > %d\n", + urb->actual_length, + urb->transfer_buffer_length, + urb->status); - acm = wb->instance; acm_write_done(acm, wb); if (ACM_READY(acm)) schedule_work(&acm->work); + else + wake_up_interruptible(&acm->drain_wait); } static void acm_softint(struct work_struct *work) { struct acm *acm = container_of(work, struct acm, work); - dbg("Entering acm_softint."); - + + dev_vdbg(&acm->data->dev, "tx work\n"); if (!ACM_READY(acm)) return; tty_wakeup(acm->tty); @@ -603,6 +622,8 @@ static void acm_tty_unregister(struct acm *acm) kfree(acm); } +static int acm_tty_chars_in_buffer(struct tty_struct *tty); + static void acm_tty_close(struct tty_struct *tty, struct file *filp) { struct acm *acm = tty->driver_data; @@ -617,6 +638,13 @@ static void acm_tty_close(struct tty_struct *tty, struct file *filp) if (acm->dev) { usb_autopm_get_interface(acm->control); acm_set_control(acm, acm->ctrlout = 0); + + /* try letting the last writes drain naturally */ + wait_event_interruptible_timeout(acm->drain_wait, + (ACM_NW == acm_wb_is_avail(acm)) + || !acm->dev, + ACM_CLOSE_TIMEOUT * HZ); + usb_kill_urb(acm->ctrlurb); for (i = 0; i < ACM_NW; i++) usb_kill_urb(acm->wb[i].urb); @@ -1047,6 +1075,7 @@ skip_normal_probe: acm->urb_task.data = (unsigned long) acm; INIT_WORK(&acm->work, acm_softint); INIT_WORK(&acm->waker, acm_waker); + init_waitqueue_head(&acm->drain_wait); spin_lock_init(&acm->throttle_lock); spin_lock_init(&acm->write_lock); spin_lock_init(&acm->read_lock); diff --git a/drivers/usb/class/cdc-acm.h b/drivers/usb/class/cdc-acm.h index 94266362ca6..1f95e7aa1b6 100644 --- a/drivers/usb/class/cdc-acm.h +++ b/drivers/usb/class/cdc-acm.h @@ -113,6 +113,7 @@ struct acm { struct usb_cdc_line_coding line; /* bits, stop, parity */ struct work_struct work; /* work queue entry for line discipline waking up */ struct work_struct waker; + wait_queue_head_t drain_wait; /* close processing */ struct tasklet_struct urb_task; /* rx processing */ spinlock_t throttle_lock; /* synchronize throtteling and read callback */ unsigned int ctrlin; /* input control lines (DCD, DSR, RI, break, overruns) */ -- GitLab From e12cc34527dcd945597c860c25aba92883a4a6a4 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Thu, 7 Aug 2008 16:29:25 +0400 Subject: [PATCH 312/750] USB: omap_udc: fix compilation with debug enabled Signed-off-by: Dmitry Baryshkov Acked-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/omap_udc.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/usb/gadget/omap_udc.c b/drivers/usb/gadget/omap_udc.c index 376e80c0753..574c53831a0 100644 --- a/drivers/usb/gadget/omap_udc.c +++ b/drivers/usb/gadget/omap_udc.c @@ -54,6 +54,7 @@ #include #include +#include #include "omap_udc.h" @@ -2310,10 +2311,10 @@ static int proc_otg_show(struct seq_file *s) u32 trans; char *ctrl_name; - tmp = OTG_REV_REG; + tmp = omap_readl(OTG_REV); if (cpu_is_omap24xx()) { ctrl_name = "control_devconf"; - trans = CONTROL_DEVCONF_REG; + trans = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0); } else { ctrl_name = "tranceiver_ctrl"; trans = omap_readw(USB_TRANSCEIVER_CTRL); -- GitLab From ab1666c1364a209e6141d7c14e47a42b5f00eca2 Mon Sep 17 00:00:00 2001 From: Libin Yang Date: Fri, 8 Aug 2008 15:03:31 +0800 Subject: [PATCH 313/750] USB: quirk PLL power down mode On some AMD 700 series southbridges, ISO OUT transfers (such as audio playback through speakers) on the USB OHCI controller may be corrupted when an A-Link express power saving feature is active. PLL power down mode in conjunction with link power management feature L1 being enabled is the bad combination ... this patch prevents them from being enabled when ISO transfers are pending. Signed-off-by: Crane Cai Signed-off-by: Libin Yang Signed-off-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ohci-hcd.c | 17 +++++ drivers/usb/host/ohci-pci.c | 132 ++++++++++++++++++++++++++++++++++++ drivers/usb/host/ohci-q.c | 6 ++ drivers/usb/host/ohci.h | 9 +++ 4 files changed, 164 insertions(+) diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c index 96fe76e9a6c..89901962cbf 100644 --- a/drivers/usb/host/ohci-hcd.c +++ b/drivers/usb/host/ohci-hcd.c @@ -86,6 +86,21 @@ static void ohci_stop (struct usb_hcd *hcd); static int ohci_restart (struct ohci_hcd *ohci); #endif +#ifdef CONFIG_PCI +static void quirk_amd_pll(int state); +static void amd_iso_dev_put(void); +#else +static inline void quirk_amd_pll(int state) +{ + return; +} +static inline void amd_iso_dev_put(void) +{ + return; +} +#endif + + #include "ohci-hub.c" #include "ohci-dbg.c" #include "ohci-mem.c" @@ -886,6 +901,8 @@ static void ohci_stop (struct usb_hcd *hcd) if (quirk_zfmicro(ohci)) del_timer(&ohci->unlink_watchdog); + if (quirk_amdiso(ohci)) + amd_iso_dev_put(); remove_debug_files (ohci); ohci_mem_cleanup (ohci); diff --git a/drivers/usb/host/ohci-pci.c b/drivers/usb/host/ohci-pci.c index 4696cc912e1..083e8df0a81 100644 --- a/drivers/usb/host/ohci-pci.c +++ b/drivers/usb/host/ohci-pci.c @@ -18,6 +18,28 @@ #error "This file is PCI bus glue. CONFIG_PCI must be defined." #endif +#include +#include + + +/* constants used to work around PM-related transfer + * glitches in some AMD 700 series southbridges + */ +#define AB_REG_BAR 0xf0 +#define AB_INDX(addr) ((addr) + 0x00) +#define AB_DATA(addr) ((addr) + 0x04) +#define AX_INDXC 0X30 +#define AX_DATAC 0x34 + +#define NB_PCIE_INDX_ADDR 0xe0 +#define NB_PCIE_INDX_DATA 0xe4 +#define PCIE_P_CNTL 0x10040 +#define BIF_NB 0x10002 + +static struct pci_dev *amd_smbus_dev; +static struct pci_dev *amd_hb_dev; +static int amd_ohci_iso_count; + /*-------------------------------------------------------------------------*/ static int broken_suspend(struct usb_hcd *hcd) @@ -143,6 +165,103 @@ static int ohci_quirk_nec(struct usb_hcd *hcd) return 0; } +static int ohci_quirk_amd700(struct usb_hcd *hcd) +{ + struct ohci_hcd *ohci = hcd_to_ohci(hcd); + u8 rev = 0; + + if (!amd_smbus_dev) + amd_smbus_dev = pci_get_device(PCI_VENDOR_ID_ATI, + PCI_DEVICE_ID_ATI_SBX00_SMBUS, NULL); + if (!amd_smbus_dev) + return 0; + + pci_read_config_byte(amd_smbus_dev, PCI_REVISION_ID, &rev); + if ((rev > 0x3b) || (rev < 0x30)) { + pci_dev_put(amd_smbus_dev); + amd_smbus_dev = NULL; + return 0; + } + + amd_ohci_iso_count++; + + if (!amd_hb_dev) + amd_hb_dev = pci_get_device(PCI_VENDOR_ID_AMD, 0x9600, NULL); + + ohci->flags |= OHCI_QUIRK_AMD_ISO; + ohci_dbg(ohci, "enabled AMD ISO transfers quirk\n"); + + return 0; +} + +/* + * The hardware normally enables the A-link power management feature, which + * lets the system lower the power consumption in idle states. + * + * Assume the system is configured to have USB 1.1 ISO transfers going + * to or from a USB device. Without this quirk, that stream may stutter + * or have breaks occasionally. For transfers going to speakers, this + * makes a very audible mess... + * + * That audio playback corruption is due to the audio stream getting + * interrupted occasionally when the link goes in lower power state + * This USB quirk prevents the link going into that lower power state + * during audio playback or other ISO operations. + */ +static void quirk_amd_pll(int on) +{ + u32 addr; + u32 val; + u32 bit = (on > 0) ? 1 : 0; + + pci_read_config_dword(amd_smbus_dev, AB_REG_BAR, &addr); + + /* BIT names/meanings are NDA-protected, sorry ... */ + + outl(AX_INDXC, AB_INDX(addr)); + outl(0x40, AB_DATA(addr)); + outl(AX_DATAC, AB_INDX(addr)); + val = inl(AB_DATA(addr)); + val &= ~((1 << 3) | (1 << 4) | (1 << 9)); + val |= (bit << 3) | ((!bit) << 4) | ((!bit) << 9); + outl(val, AB_DATA(addr)); + + if (amd_hb_dev) { + addr = PCIE_P_CNTL; + pci_write_config_dword(amd_hb_dev, NB_PCIE_INDX_ADDR, addr); + + pci_read_config_dword(amd_hb_dev, NB_PCIE_INDX_DATA, &val); + val &= ~(1 | (1 << 3) | (1 << 4) | (1 << 9) | (1 << 12)); + val |= bit | (bit << 3) | (bit << 12); + val |= ((!bit) << 4) | ((!bit) << 9); + pci_write_config_dword(amd_hb_dev, NB_PCIE_INDX_DATA, val); + + addr = BIF_NB; + pci_write_config_dword(amd_hb_dev, NB_PCIE_INDX_ADDR, addr); + + pci_read_config_dword(amd_hb_dev, NB_PCIE_INDX_DATA, &val); + val &= ~(1 << 8); + val |= bit << 8; + pci_write_config_dword(amd_hb_dev, NB_PCIE_INDX_DATA, val); + } +} + +static void amd_iso_dev_put(void) +{ + amd_ohci_iso_count--; + if (amd_ohci_iso_count == 0) { + if (amd_smbus_dev) { + pci_dev_put(amd_smbus_dev); + amd_smbus_dev = NULL; + } + if (amd_hb_dev) { + pci_dev_put(amd_hb_dev); + amd_hb_dev = NULL; + } + } + +} + /* List of quirks for OHCI */ static const struct pci_device_id ohci_pci_quirks[] = { { @@ -181,6 +300,19 @@ static const struct pci_device_id ohci_pci_quirks[] = { PCI_DEVICE(PCI_VENDOR_ID_ITE, 0x8152), .driver_data = (unsigned long) broken_suspend, }, + { + PCI_DEVICE(PCI_VENDOR_ID_ATI, 0x4397), + .driver_data = (unsigned long)ohci_quirk_amd700, + }, + { + PCI_DEVICE(PCI_VENDOR_ID_ATI, 0x4398), + .driver_data = (unsigned long)ohci_quirk_amd700, + }, + { + PCI_DEVICE(PCI_VENDOR_ID_ATI, 0x4399), + .driver_data = (unsigned long)ohci_quirk_amd700, + }, + /* FIXME for some of the early AMD 760 southbridges, OHCI * won't work at all. blacklist them. */ diff --git a/drivers/usb/host/ohci-q.c b/drivers/usb/host/ohci-q.c index 6a9b4c55795..c2d80f80448 100644 --- a/drivers/usb/host/ohci-q.c +++ b/drivers/usb/host/ohci-q.c @@ -49,6 +49,9 @@ __acquires(ohci->lock) switch (usb_pipetype (urb->pipe)) { case PIPE_ISOCHRONOUS: ohci_to_hcd(ohci)->self.bandwidth_isoc_reqs--; + if (ohci_to_hcd(ohci)->self.bandwidth_isoc_reqs == 0 + && quirk_amdiso(ohci)) + quirk_amd_pll(1); break; case PIPE_INTERRUPT: ohci_to_hcd(ohci)->self.bandwidth_int_reqs--; @@ -677,6 +680,9 @@ static void td_submit_urb ( data + urb->iso_frame_desc [cnt].offset, urb->iso_frame_desc [cnt].length, urb, cnt); } + if (ohci_to_hcd(ohci)->self.bandwidth_isoc_reqs == 0 + && quirk_amdiso(ohci)) + quirk_amd_pll(0); periodic = ohci_to_hcd(ohci)->self.bandwidth_isoc_reqs++ == 0 && ohci_to_hcd(ohci)->self.bandwidth_int_reqs == 0; break; diff --git a/drivers/usb/host/ohci.h b/drivers/usb/host/ohci.h index df5a8037dba..faf622eafce 100644 --- a/drivers/usb/host/ohci.h +++ b/drivers/usb/host/ohci.h @@ -401,6 +401,7 @@ struct ohci_hcd { #define OHCI_QUIRK_NEC 0x40 /* lost interrupts */ #define OHCI_QUIRK_FRAME_NO 0x80 /* no big endian frame_no shift */ #define OHCI_QUIRK_HUB_POWER 0x100 /* distrust firmware power/oc setup */ +#define OHCI_QUIRK_AMD_ISO 0x200 /* ISO transfers*/ // there are also chip quirks/bugs in init logic struct work_struct nec_work; /* Worker for NEC quirk */ @@ -428,6 +429,10 @@ static inline int quirk_zfmicro(struct ohci_hcd *ohci) { return ohci->flags & OHCI_QUIRK_ZFMICRO; } +static inline int quirk_amdiso(struct ohci_hcd *ohci) +{ + return ohci->flags & OHCI_QUIRK_AMD_ISO; +} #else static inline int quirk_nec(struct ohci_hcd *ohci) { @@ -437,6 +442,10 @@ static inline int quirk_zfmicro(struct ohci_hcd *ohci) { return 0; } +static inline int quirk_amdiso(struct ohci_hcd *ohci) +{ + return 0; +} #endif /* convert between an hcd pointer and the corresponding ohci_hcd */ -- GitLab From 6188a83f7264edebe9b8ee10ad7b2136d3531ea6 Mon Sep 17 00:00:00 2001 From: Oliver Martin Date: Sat, 9 Aug 2008 04:49:26 +0200 Subject: [PATCH 314/750] USB: Add vendor/product id of ZTE MF628 to option This adds the vendor and product id (19d2:0015) of the ZTE MF628 HSDPA modem to the option driver. It still needs a mode switch command issued beforehand, this is currently handled by a userspace tool. Signed-off-by: Oliver Martin Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index e7753ccaf70..df472c7480a 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -214,6 +214,10 @@ static int option_send_setup(struct tty_struct *tty, struct usb_serial_port *po #define TELIT_VENDOR_ID 0x1bc7 #define TELIT_PRODUCT_UC864E 0x1003 +/* ZTE PRODUCTS */ +#define ZTE_VENDOR_ID 0x19d2 +#define ZTE_PRODUCT_MF628 0x0015 + static struct usb_device_id option_ids[] = { { USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_COLT) }, { USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_RICOLA) }, @@ -340,6 +344,7 @@ static struct usb_device_id option_ids[] = { { USB_DEVICE(QUALCOMM_VENDOR_ID, 0x6613)}, /* Onda H600/ZTE MF330 */ { USB_DEVICE(MAXON_VENDOR_ID, 0x6280) }, /* BP3-USB & BP3-EXT HSDPA */ { USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_UC864E) }, + { USB_DEVICE(ZTE_VENDOR_ID, ZTE_PRODUCT_MF628) }, { } /* Terminating entry */ }; MODULE_DEVICE_TABLE(usb, option_ids); -- GitLab From f331e40ee8e4861e1d82310b1af7cf75de7370ac Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Tue, 12 Aug 2008 12:04:50 +0700 Subject: [PATCH 315/750] USB: serial: remove CONFIG_USB_DEBUG from sierra and option drivers These drivers should not be relying on CONFIG_USB_DEBUG. By doing this, it prevents users of kernels that do not enable this option from enabling debugging in these drivers, unlike all other usb-serial drivers. Cc: Matthias Urlichs Cc: Kevin Lloyd Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 7 ------- drivers/usb/serial/sierra.c | 2 -- 2 files changed, 9 deletions(-) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index df472c7480a..e143198aeb0 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -383,11 +383,7 @@ static struct usb_serial_driver option_1port_device = { .read_int_callback = option_instat_callback, }; -#ifdef CONFIG_USB_DEBUG static int debug; -#else -#define debug 0 -#endif /* per port private data */ @@ -991,8 +987,5 @@ MODULE_DESCRIPTION(DRIVER_DESC); MODULE_VERSION(DRIVER_VERSION); MODULE_LICENSE("GPL"); -#ifdef CONFIG_USB_DEBUG module_param(debug, bool, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(debug, "Debug messages"); -#endif - diff --git a/drivers/usb/serial/sierra.c b/drivers/usb/serial/sierra.c index 6b7ed333386..706033753ad 100644 --- a/drivers/usb/serial/sierra.c +++ b/drivers/usb/serial/sierra.c @@ -766,7 +766,5 @@ MODULE_LICENSE("GPL"); module_param(nmea, bool, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(nmea, "NMEA streaming"); -#ifdef CONFIG_USB_DEBUG module_param(debug, bool, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(debug, "Debug messages"); -#endif -- GitLab From 550a7375fe720924241f0eb76e4a5c1a3eb8c32f Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Thu, 24 Jul 2008 12:27:36 +0300 Subject: [PATCH 316/750] USB: Add MUSB and TUSB support This patch adds support for MUSB and TUSB controllers integrated into omap2430 and davinci. It also adds support for external tusb6010 controller. Cc: David Brownell Cc: Tony Lindgren Signed-off-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman --- MAINTAINERS | 6 + drivers/Makefile | 1 + drivers/usb/Kconfig | 2 + drivers/usb/gadget/Kconfig | 10 + drivers/usb/musb/Kconfig | 176 +++ drivers/usb/musb/Makefile | 86 ++ drivers/usb/musb/cppi_dma.c | 1540 +++++++++++++++++++ drivers/usb/musb/cppi_dma.h | 133 ++ drivers/usb/musb/davinci.c | 462 ++++++ drivers/usb/musb/davinci.h | 100 ++ drivers/usb/musb/musb_core.c | 2266 ++++++++++++++++++++++++++++ drivers/usb/musb/musb_core.h | 517 +++++++ drivers/usb/musb/musb_debug.h | 66 + drivers/usb/musb/musb_dma.h | 172 +++ drivers/usb/musb/musb_gadget.c | 2033 +++++++++++++++++++++++++ drivers/usb/musb/musb_gadget.h | 108 ++ drivers/usb/musb/musb_gadget_ep0.c | 981 ++++++++++++ drivers/usb/musb/musb_host.c | 2170 ++++++++++++++++++++++++++ drivers/usb/musb/musb_host.h | 110 ++ drivers/usb/musb/musb_io.h | 115 ++ drivers/usb/musb/musb_procfs.c | 830 ++++++++++ drivers/usb/musb/musb_regs.h | 300 ++++ drivers/usb/musb/musb_virthub.c | 425 ++++++ drivers/usb/musb/musbhsdma.c | 433 ++++++ drivers/usb/musb/omap2430.c | 324 ++++ drivers/usb/musb/omap2430.h | 56 + drivers/usb/musb/tusb6010.c | 1151 ++++++++++++++ drivers/usb/musb/tusb6010.h | 402 +++++ drivers/usb/musb/tusb6010_omap.c | 719 +++++++++ include/linux/usb/musb.h | 70 + 30 files changed, 15764 insertions(+) create mode 100644 drivers/usb/musb/Kconfig create mode 100644 drivers/usb/musb/Makefile create mode 100644 drivers/usb/musb/cppi_dma.c create mode 100644 drivers/usb/musb/cppi_dma.h create mode 100644 drivers/usb/musb/davinci.c create mode 100644 drivers/usb/musb/davinci.h create mode 100644 drivers/usb/musb/musb_core.c create mode 100644 drivers/usb/musb/musb_core.h create mode 100644 drivers/usb/musb/musb_debug.h create mode 100644 drivers/usb/musb/musb_dma.h create mode 100644 drivers/usb/musb/musb_gadget.c create mode 100644 drivers/usb/musb/musb_gadget.h create mode 100644 drivers/usb/musb/musb_gadget_ep0.c create mode 100644 drivers/usb/musb/musb_host.c create mode 100644 drivers/usb/musb/musb_host.h create mode 100644 drivers/usb/musb/musb_io.h create mode 100644 drivers/usb/musb/musb_procfs.c create mode 100644 drivers/usb/musb/musb_regs.h create mode 100644 drivers/usb/musb/musb_virthub.c create mode 100644 drivers/usb/musb/musbhsdma.c create mode 100644 drivers/usb/musb/omap2430.c create mode 100644 drivers/usb/musb/omap2430.h create mode 100644 drivers/usb/musb/tusb6010.c create mode 100644 drivers/usb/musb/tusb6010.h create mode 100644 drivers/usb/musb/tusb6010_omap.c create mode 100644 include/linux/usb/musb.h diff --git a/MAINTAINERS b/MAINTAINERS index 0c42dc25e0e..773d6bc3a9a 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2928,6 +2928,12 @@ M: jirislaby@gmail.com L: linux-kernel@vger.kernel.org S: Maintained +MUSB MULTIPOINT HIGH SPEED DUAL-ROLE CONTROLLER +P: Felipe Balbi +M: felipe.balbi@nokia.com +L: linux-usb@vger.kernel.org +S: Maintained + MYRICOM MYRI-10G 10GbE DRIVER (MYRI10GE) P: Andrew Gallatin M: gallatin@myri.com diff --git a/drivers/Makefile b/drivers/Makefile index a280ab3d083..2735bde7347 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -57,6 +57,7 @@ obj-$(CONFIG_ATA_OVER_ETH) += block/aoe/ obj-$(CONFIG_PARIDE) += block/paride/ obj-$(CONFIG_TC) += tc/ obj-$(CONFIG_USB) += usb/ +obj-$(CONFIG_USB_MUSB_HDRC) += usb/musb/ obj-$(CONFIG_PCI) += usb/ obj-$(CONFIG_USB_GADGET) += usb/gadget/ obj-$(CONFIG_SERIO) += input/serio/ diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig index 4f9b5ecfb72..bcefbddeba5 100644 --- a/drivers/usb/Kconfig +++ b/drivers/usb/Kconfig @@ -99,6 +99,8 @@ source "drivers/usb/mon/Kconfig" source "drivers/usb/host/Kconfig" +source "drivers/usb/musb/Kconfig" + source "drivers/usb/class/Kconfig" source "drivers/usb/storage/Kconfig" diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig index c6a8c6b1116..acc95b2ac6f 100644 --- a/drivers/usb/gadget/Kconfig +++ b/drivers/usb/gadget/Kconfig @@ -284,6 +284,16 @@ config USB_LH7A40X default USB_GADGET select USB_GADGET_SELECTED +# built in ../musb along with host support +config USB_GADGET_MUSB_HDRC + boolean "Inventra HDRC USB Peripheral (TI, ...)" + depends on USB_MUSB_HDRC && (USB_MUSB_PERIPHERAL || USB_MUSB_OTG) + select USB_GADGET_DUALSPEED + select USB_GADGET_SELECTED + help + This OTG-capable silicon IP is used in dual designs including + the TI DaVinci, OMAP 243x, OMAP 343x, and TUSB 6010. + config USB_GADGET_OMAP boolean "OMAP USB Device Controller" depends on ARCH_OMAP diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig new file mode 100644 index 00000000000..faca4333f27 --- /dev/null +++ b/drivers/usb/musb/Kconfig @@ -0,0 +1,176 @@ +# +# USB Dual Role (OTG-ready) Controller Drivers +# for silicon based on Mentor Graphics INVENTRA designs +# + +comment "Enable Host or Gadget support to see Inventra options" + depends on !USB && USB_GADGET=n + +# (M)HDRC = (Multipoint) Highspeed Dual-Role Controller +config USB_MUSB_HDRC + depends on (USB || USB_GADGET) && HAVE_CLK + select TWL4030_USB if MACH_OMAP_3430SDP + tristate 'Inventra Highspeed Dual Role Controller (TI, ...)' + help + Say Y here if your system has a dual role high speed USB + controller based on the Mentor Graphics silicon IP. Then + configure options to match your silicon and the board + it's being used with, including the USB peripheral role, + or the USB host role, or both. + + Texas Instruments parts using this IP include DaVinci 644x, + OMAP 243x, OMAP 343x, and TUSB 6010. + + If you do not know what this is, please say N. + + To compile this driver as a module, choose M here; the + module will be called "musb_hdrc". + +config USB_MUSB_SOC + boolean + depends on USB_MUSB_HDRC + default y if ARCH_DAVINCI + default y if ARCH_OMAP2430 + default y if ARCH_OMAP34XX + help + Use a static file to describe how the + controller is configured (endpoints, mechanisms, etc) on the + current iteration of a given system-on-chip. + +comment "DaVinci 644x USB support" + depends on USB_MUSB_HDRC && ARCH_DAVINCI + +comment "OMAP 243x high speed USB support" + depends on USB_MUSB_HDRC && ARCH_OMAP2430 + +comment "OMAP 343x high speed USB support" + depends on USB_MUSB_HDRC && ARCH_OMAP34XX + +config USB_TUSB6010 + boolean "TUSB 6010 support" + depends on USB_MUSB_HDRC && !USB_MUSB_SOC + default y + help + The TUSB 6010 chip, from Texas Instruments, connects a discrete + HDRC core using a 16-bit parallel bus (NOR flash style) or VLYNQ + (a high speed serial link). It can use system-specific external + DMA controllers. + +choice + prompt "Driver Mode" + depends on USB_MUSB_HDRC + help + Dual-Role devices can support both host and peripheral roles, + as well as a the special "OTG Device" role which can switch + between both roles as needed. + +# use USB_MUSB_HDRC_HCD not USB_MUSB_HOST to #ifdef host side support; +# OTG needs both roles, not just USB_MUSB_HOST. +config USB_MUSB_HOST + depends on USB + bool "USB Host" + help + Say Y here if your system supports the USB host role. + If it has a USB "A" (rectangular), "Mini-A" (uncommon), + or "Mini-AB" connector, it supports the host role. + (With a "Mini-AB" connector, you should enable USB OTG.) + +# use USB_GADGET_MUSB_HDRC not USB_MUSB_PERIPHERAL to #ifdef peripheral +# side support ... OTG needs both roles +config USB_MUSB_PERIPHERAL + depends on USB_GADGET + bool "USB Peripheral (gadget stack)" + select USB_GADGET_MUSB_HDRC + help + Say Y here if your system supports the USB peripheral role. + If it has a USB "B" (squarish), "Mini-B", or "Mini-AB" + connector, it supports the peripheral role. + (With a "Mini-AB" connector, you should enable USB OTG.) + +config USB_MUSB_OTG + depends on USB && USB_GADGET && PM && EXPERIMENTAL + bool "Both host and peripheral: USB OTG (On The Go) Device" + select USB_GADGET_MUSB_HDRC + select USB_OTG + help + The most notable feature of USB OTG is support for a + "Dual-Role" device, which can act as either a device + or a host. The initial role choice can be changed + later, when two dual-role devices talk to each other. + + At this writing, the OTG support in this driver is incomplete, + omitting the mandatory HNP or SRP protocols. However, some + of the cable based role switching works. (That is, grounding + the ID pin switches the controller to host mode, while leaving + it floating leaves it in peripheral mode.) + + Select this if your system has a Mini-AB connector, or + to simplify certain kinds of configuration. + + To implement your OTG Targeted Peripherals List (TPL), enable + USB_OTG_WHITELIST and update "drivers/usb/core/otg_whitelist.h" + to match your requirements. + +endchoice + +# enable peripheral support (including with OTG) +config USB_GADGET_MUSB_HDRC + bool + depends on USB_MUSB_HDRC && (USB_MUSB_PERIPHERAL || USB_MUSB_OTG) +# default y +# select USB_GADGET_DUALSPEED +# select USB_GADGET_SELECTED + +# enables host support (including with OTG) +config USB_MUSB_HDRC_HCD + bool + depends on USB_MUSB_HDRC && (USB_MUSB_HOST || USB_MUSB_OTG) + select USB_OTG if USB_GADGET_MUSB_HDRC + default y + + +config MUSB_PIO_ONLY + bool 'Disable DMA (always use PIO)' + depends on USB_MUSB_HDRC + default y if USB_TUSB6010 + help + All data is copied between memory and FIFO by the CPU. + DMA controllers are ignored. + + Do not select 'n' here unless DMA support for your SOC or board + is unavailable (or unstable). When DMA is enabled at compile time, + you can still disable it at run time using the "use_dma=n" module + parameter. + +config USB_INVENTRA_DMA + bool + depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY + default ARCH_OMAP2430 || ARCH_OMAP34XX + help + Enable DMA transfers using Mentor's engine. + +config USB_TI_CPPI_DMA + bool + depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY + default ARCH_DAVINCI + help + Enable DMA transfers when TI CPPI DMA is available. + +config USB_TUSB_OMAP_DMA + bool + depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY + depends on USB_TUSB6010 + depends on ARCH_OMAP + default y + help + Enable DMA transfers on TUSB 6010 when OMAP DMA is available. + +config USB_MUSB_LOGLEVEL + depends on USB_MUSB_HDRC + int 'Logging Level (0 - none / 3 - annoying / ... )' + default 0 + help + Set the logging level. 0 disables the debugging altogether, + although when USB_DEBUG is set the value is at least 1. + Starting at level 3, per-transfer (urb, usb_request, packet, + or dma transfer) tracing may kick in. diff --git a/drivers/usb/musb/Makefile b/drivers/usb/musb/Makefile new file mode 100644 index 00000000000..88eb67de08a --- /dev/null +++ b/drivers/usb/musb/Makefile @@ -0,0 +1,86 @@ +# +# for USB OTG silicon based on Mentor Graphics INVENTRA designs +# + +musb_hdrc-objs := musb_core.o + +obj-$(CONFIG_USB_MUSB_HDRC) += musb_hdrc.o + +ifeq ($(CONFIG_ARCH_DAVINCI),y) + musb_hdrc-objs += davinci.o +endif + +ifeq ($(CONFIG_USB_TUSB6010),y) + musb_hdrc-objs += tusb6010.o +endif + +ifeq ($(CONFIG_ARCH_OMAP2430),y) + musb_hdrc-objs += omap2430.o +endif + +ifeq ($(CONFIG_ARCH_OMAP3430),y) + musb_hdrc-objs += omap2430.o +endif + +ifeq ($(CONFIG_USB_GADGET_MUSB_HDRC),y) + musb_hdrc-objs += musb_gadget_ep0.o musb_gadget.o +endif + +ifeq ($(CONFIG_USB_MUSB_HDRC_HCD),y) + musb_hdrc-objs += musb_virthub.o musb_host.o +endif + +# the kconfig must guarantee that only one of the +# possible I/O schemes will be enabled at a time ... +# PIO only, or DMA (several potential schemes). +# though PIO is always there to back up DMA, and for ep0 + +ifneq ($(CONFIG_MUSB_PIO_ONLY),y) + + ifeq ($(CONFIG_USB_INVENTRA_DMA),y) + musb_hdrc-objs += musbhsdma.o + + else + ifeq ($(CONFIG_USB_TI_CPPI_DMA),y) + musb_hdrc-objs += cppi_dma.o + + else + ifeq ($(CONFIG_USB_TUSB_OMAP_DMA),y) + musb_hdrc-objs += tusb6010_omap.o + + endif + endif + endif +endif + + +################################################################################ + +# FIXME remove all these extra "-DMUSB_* things, stick to CONFIG_* + +ifeq ($(CONFIG_USB_INVENTRA_MUSB_HAS_AHB_ID),y) + EXTRA_CFLAGS += -DMUSB_AHB_ID +endif + +# Debugging + +MUSB_DEBUG:=$(CONFIG_USB_MUSB_LOGLEVEL) + +ifeq ("$(strip $(MUSB_DEBUG))","") + ifdef CONFIG_USB_DEBUG + MUSB_DEBUG:=1 + else + MUSB_DEBUG:=0 + endif +endif + +ifneq ($(MUSB_DEBUG),0) + EXTRA_CFLAGS += -DDEBUG + + ifeq ($(CONFIG_PROC_FS),y) + musb_hdrc-objs += musb_procfs.o + endif + +endif + +EXTRA_CFLAGS += -DMUSB_DEBUG=$(MUSB_DEBUG) diff --git a/drivers/usb/musb/cppi_dma.c b/drivers/usb/musb/cppi_dma.c new file mode 100644 index 00000000000..5ad6d0893cb --- /dev/null +++ b/drivers/usb/musb/cppi_dma.c @@ -0,0 +1,1540 @@ +/* + * Copyright (C) 2005-2006 by Texas Instruments + * + * This file implements a DMA interface using TI's CPPI DMA. + * For now it's DaVinci-only, but CPPI isn't specific to DaVinci or USB. + * The TUSB6020, using VLYNQ, has CPPI that looks much like DaVinci. + */ + +#include + +#include "musb_core.h" +#include "cppi_dma.h" + + +/* CPPI DMA status 7-mar-2006: + * + * - See musb_{host,gadget}.c for more info + * + * - Correct RX DMA generally forces the engine into irq-per-packet mode, + * which can easily saturate the CPU under non-mass-storage loads. + * + * NOTES 24-aug-2006 (2.6.18-rc4): + * + * - peripheral RXDMA wedged in a test with packets of length 512/512/1. + * evidently after the 1 byte packet was received and acked, the queue + * of BDs got garbaged so it wouldn't empty the fifo. (rxcsr 0x2003, + * and RX DMA0: 4 left, 80000000 8feff880, 8feff860 8feff860; 8f321401 + * 004001ff 00000001 .. 8feff860) Host was just getting NAKed on tx + * of its next (512 byte) packet. IRQ issues? + * + * REVISIT: the "transfer DMA" glue between CPPI and USB fifos will + * evidently also directly update the RX and TX CSRs ... so audit all + * host and peripheral side DMA code to avoid CSR access after DMA has + * been started. + */ + +/* REVISIT now we can avoid preallocating these descriptors; or + * more simply, switch to a global freelist not per-channel ones. + * Note: at full speed, 64 descriptors == 4K bulk data. + */ +#define NUM_TXCHAN_BD 64 +#define NUM_RXCHAN_BD 64 + +static inline void cpu_drain_writebuffer(void) +{ + wmb(); +#ifdef CONFIG_CPU_ARM926T + /* REVISIT this "should not be needed", + * but lack of it sure seemed to hurt ... + */ + asm("mcr p15, 0, r0, c7, c10, 4 @ drain write buffer\n"); +#endif +} + +static inline struct cppi_descriptor *cppi_bd_alloc(struct cppi_channel *c) +{ + struct cppi_descriptor *bd = c->freelist; + + if (bd) + c->freelist = bd->next; + return bd; +} + +static inline void +cppi_bd_free(struct cppi_channel *c, struct cppi_descriptor *bd) +{ + if (!bd) + return; + bd->next = c->freelist; + c->freelist = bd; +} + +/* + * Start DMA controller + * + * Initialize the DMA controller as necessary. + */ + +/* zero out entire rx state RAM entry for the channel */ +static void cppi_reset_rx(struct cppi_rx_stateram __iomem *rx) +{ + musb_writel(&rx->rx_skipbytes, 0, 0); + musb_writel(&rx->rx_head, 0, 0); + musb_writel(&rx->rx_sop, 0, 0); + musb_writel(&rx->rx_current, 0, 0); + musb_writel(&rx->rx_buf_current, 0, 0); + musb_writel(&rx->rx_len_len, 0, 0); + musb_writel(&rx->rx_cnt_cnt, 0, 0); +} + +/* zero out entire tx state RAM entry for the channel */ +static void cppi_reset_tx(struct cppi_tx_stateram __iomem *tx, u32 ptr) +{ + musb_writel(&tx->tx_head, 0, 0); + musb_writel(&tx->tx_buf, 0, 0); + musb_writel(&tx->tx_current, 0, 0); + musb_writel(&tx->tx_buf_current, 0, 0); + musb_writel(&tx->tx_info, 0, 0); + musb_writel(&tx->tx_rem_len, 0, 0); + /* musb_writel(&tx->tx_dummy, 0, 0); */ + musb_writel(&tx->tx_complete, 0, ptr); +} + +static void __init cppi_pool_init(struct cppi *cppi, struct cppi_channel *c) +{ + int j; + + /* initialize channel fields */ + c->head = NULL; + c->tail = NULL; + c->last_processed = NULL; + c->channel.status = MUSB_DMA_STATUS_UNKNOWN; + c->controller = cppi; + c->is_rndis = 0; + c->freelist = NULL; + + /* build the BD Free list for the channel */ + for (j = 0; j < NUM_TXCHAN_BD + 1; j++) { + struct cppi_descriptor *bd; + dma_addr_t dma; + + bd = dma_pool_alloc(cppi->pool, GFP_KERNEL, &dma); + bd->dma = dma; + cppi_bd_free(c, bd); + } +} + +static int cppi_channel_abort(struct dma_channel *); + +static void cppi_pool_free(struct cppi_channel *c) +{ + struct cppi *cppi = c->controller; + struct cppi_descriptor *bd; + + (void) cppi_channel_abort(&c->channel); + c->channel.status = MUSB_DMA_STATUS_UNKNOWN; + c->controller = NULL; + + /* free all its bds */ + bd = c->last_processed; + do { + if (bd) + dma_pool_free(cppi->pool, bd, bd->dma); + bd = cppi_bd_alloc(c); + } while (bd); + c->last_processed = NULL; +} + +static int __init cppi_controller_start(struct dma_controller *c) +{ + struct cppi *controller; + void __iomem *tibase; + int i; + + controller = container_of(c, struct cppi, controller); + + /* do whatever is necessary to start controller */ + for (i = 0; i < ARRAY_SIZE(controller->tx); i++) { + controller->tx[i].transmit = true; + controller->tx[i].index = i; + } + for (i = 0; i < ARRAY_SIZE(controller->rx); i++) { + controller->rx[i].transmit = false; + controller->rx[i].index = i; + } + + /* setup BD list on a per channel basis */ + for (i = 0; i < ARRAY_SIZE(controller->tx); i++) + cppi_pool_init(controller, controller->tx + i); + for (i = 0; i < ARRAY_SIZE(controller->rx); i++) + cppi_pool_init(controller, controller->rx + i); + + tibase = controller->tibase; + INIT_LIST_HEAD(&controller->tx_complete); + + /* initialise tx/rx channel head pointers to zero */ + for (i = 0; i < ARRAY_SIZE(controller->tx); i++) { + struct cppi_channel *tx_ch = controller->tx + i; + struct cppi_tx_stateram __iomem *tx; + + INIT_LIST_HEAD(&tx_ch->tx_complete); + + tx = tibase + DAVINCI_TXCPPI_STATERAM_OFFSET(i); + tx_ch->state_ram = tx; + cppi_reset_tx(tx, 0); + } + for (i = 0; i < ARRAY_SIZE(controller->rx); i++) { + struct cppi_channel *rx_ch = controller->rx + i; + struct cppi_rx_stateram __iomem *rx; + + INIT_LIST_HEAD(&rx_ch->tx_complete); + + rx = tibase + DAVINCI_RXCPPI_STATERAM_OFFSET(i); + rx_ch->state_ram = rx; + cppi_reset_rx(rx); + } + + /* enable individual cppi channels */ + musb_writel(tibase, DAVINCI_TXCPPI_INTENAB_REG, + DAVINCI_DMA_ALL_CHANNELS_ENABLE); + musb_writel(tibase, DAVINCI_RXCPPI_INTENAB_REG, + DAVINCI_DMA_ALL_CHANNELS_ENABLE); + + /* enable tx/rx CPPI control */ + musb_writel(tibase, DAVINCI_TXCPPI_CTRL_REG, DAVINCI_DMA_CTRL_ENABLE); + musb_writel(tibase, DAVINCI_RXCPPI_CTRL_REG, DAVINCI_DMA_CTRL_ENABLE); + + /* disable RNDIS mode, also host rx RNDIS autorequest */ + musb_writel(tibase, DAVINCI_RNDIS_REG, 0); + musb_writel(tibase, DAVINCI_AUTOREQ_REG, 0); + + return 0; +} + +/* + * Stop DMA controller + * + * De-Init the DMA controller as necessary. + */ + +static int cppi_controller_stop(struct dma_controller *c) +{ + struct cppi *controller; + void __iomem *tibase; + int i; + + controller = container_of(c, struct cppi, controller); + + tibase = controller->tibase; + /* DISABLE INDIVIDUAL CHANNEL Interrupts */ + musb_writel(tibase, DAVINCI_TXCPPI_INTCLR_REG, + DAVINCI_DMA_ALL_CHANNELS_ENABLE); + musb_writel(tibase, DAVINCI_RXCPPI_INTCLR_REG, + DAVINCI_DMA_ALL_CHANNELS_ENABLE); + + DBG(1, "Tearing down RX and TX Channels\n"); + for (i = 0; i < ARRAY_SIZE(controller->tx); i++) { + /* FIXME restructure of txdma to use bds like rxdma */ + controller->tx[i].last_processed = NULL; + cppi_pool_free(controller->tx + i); + } + for (i = 0; i < ARRAY_SIZE(controller->rx); i++) + cppi_pool_free(controller->rx + i); + + /* in Tx Case proper teardown is supported. We resort to disabling + * Tx/Rx CPPI after cleanup of Tx channels. Before TX teardown is + * complete TX CPPI cannot be disabled. + */ + /*disable tx/rx cppi */ + musb_writel(tibase, DAVINCI_TXCPPI_CTRL_REG, DAVINCI_DMA_CTRL_DISABLE); + musb_writel(tibase, DAVINCI_RXCPPI_CTRL_REG, DAVINCI_DMA_CTRL_DISABLE); + + return 0; +} + +/* While dma channel is allocated, we only want the core irqs active + * for fault reports, otherwise we'd get irqs that we don't care about. + * Except for TX irqs, where dma done != fifo empty and reusable ... + * + * NOTE: docs don't say either way, but irq masking **enables** irqs. + * + * REVISIT same issue applies to pure PIO usage too, and non-cppi dma... + */ +static inline void core_rxirq_disable(void __iomem *tibase, unsigned epnum) +{ + musb_writel(tibase, DAVINCI_USB_INT_MASK_CLR_REG, 1 << (epnum + 8)); +} + +static inline void core_rxirq_enable(void __iomem *tibase, unsigned epnum) +{ + musb_writel(tibase, DAVINCI_USB_INT_MASK_SET_REG, 1 << (epnum + 8)); +} + + +/* + * Allocate a CPPI Channel for DMA. With CPPI, channels are bound to + * each transfer direction of a non-control endpoint, so allocating + * (and deallocating) is mostly a way to notice bad housekeeping on + * the software side. We assume the irqs are always active. + */ +static struct dma_channel * +cppi_channel_allocate(struct dma_controller *c, + struct musb_hw_ep *ep, u8 transmit) +{ + struct cppi *controller; + u8 index; + struct cppi_channel *cppi_ch; + void __iomem *tibase; + + controller = container_of(c, struct cppi, controller); + tibase = controller->tibase; + + /* ep0 doesn't use DMA; remember cppi indices are 0..N-1 */ + index = ep->epnum - 1; + + /* return the corresponding CPPI Channel Handle, and + * probably disable the non-CPPI irq until we need it. + */ + if (transmit) { + if (index >= ARRAY_SIZE(controller->tx)) { + DBG(1, "no %cX%d CPPI channel\n", 'T', index); + return NULL; + } + cppi_ch = controller->tx + index; + } else { + if (index >= ARRAY_SIZE(controller->rx)) { + DBG(1, "no %cX%d CPPI channel\n", 'R', index); + return NULL; + } + cppi_ch = controller->rx + index; + core_rxirq_disable(tibase, ep->epnum); + } + + /* REVISIT make this an error later once the same driver code works + * with the other DMA engine too + */ + if (cppi_ch->hw_ep) + DBG(1, "re-allocating DMA%d %cX channel %p\n", + index, transmit ? 'T' : 'R', cppi_ch); + cppi_ch->hw_ep = ep; + cppi_ch->channel.status = MUSB_DMA_STATUS_FREE; + + DBG(4, "Allocate CPPI%d %cX\n", index, transmit ? 'T' : 'R'); + return &cppi_ch->channel; +} + +/* Release a CPPI Channel. */ +static void cppi_channel_release(struct dma_channel *channel) +{ + struct cppi_channel *c; + void __iomem *tibase; + + /* REVISIT: for paranoia, check state and abort if needed... */ + + c = container_of(channel, struct cppi_channel, channel); + tibase = c->controller->tibase; + if (!c->hw_ep) + DBG(1, "releasing idle DMA channel %p\n", c); + else if (!c->transmit) + core_rxirq_enable(tibase, c->index + 1); + + /* for now, leave its cppi IRQ enabled (we won't trigger it) */ + c->hw_ep = NULL; + channel->status = MUSB_DMA_STATUS_UNKNOWN; +} + +/* Context: controller irqlocked */ +static void +cppi_dump_rx(int level, struct cppi_channel *c, const char *tag) +{ + void __iomem *base = c->controller->mregs; + struct cppi_rx_stateram __iomem *rx = c->state_ram; + + musb_ep_select(base, c->index + 1); + + DBG(level, "RX DMA%d%s: %d left, csr %04x, " + "%08x H%08x S%08x C%08x, " + "B%08x L%08x %08x .. %08x" + "\n", + c->index, tag, + musb_readl(c->controller->tibase, + DAVINCI_RXCPPI_BUFCNT0_REG + 4 * c->index), + musb_readw(c->hw_ep->regs, MUSB_RXCSR), + + musb_readl(&rx->rx_skipbytes, 0), + musb_readl(&rx->rx_head, 0), + musb_readl(&rx->rx_sop, 0), + musb_readl(&rx->rx_current, 0), + + musb_readl(&rx->rx_buf_current, 0), + musb_readl(&rx->rx_len_len, 0), + musb_readl(&rx->rx_cnt_cnt, 0), + musb_readl(&rx->rx_complete, 0) + ); +} + +/* Context: controller irqlocked */ +static void +cppi_dump_tx(int level, struct cppi_channel *c, const char *tag) +{ + void __iomem *base = c->controller->mregs; + struct cppi_tx_stateram __iomem *tx = c->state_ram; + + musb_ep_select(base, c->index + 1); + + DBG(level, "TX DMA%d%s: csr %04x, " + "H%08x S%08x C%08x %08x, " + "F%08x L%08x .. %08x" + "\n", + c->index, tag, + musb_readw(c->hw_ep->regs, MUSB_TXCSR), + + musb_readl(&tx->tx_head, 0), + musb_readl(&tx->tx_buf, 0), + musb_readl(&tx->tx_current, 0), + musb_readl(&tx->tx_buf_current, 0), + + musb_readl(&tx->tx_info, 0), + musb_readl(&tx->tx_rem_len, 0), + /* dummy/unused word 6 */ + musb_readl(&tx->tx_complete, 0) + ); +} + +/* Context: controller irqlocked */ +static inline void +cppi_rndis_update(struct cppi_channel *c, int is_rx, + void __iomem *tibase, int is_rndis) +{ + /* we may need to change the rndis flag for this cppi channel */ + if (c->is_rndis != is_rndis) { + u32 value = musb_readl(tibase, DAVINCI_RNDIS_REG); + u32 temp = 1 << (c->index); + + if (is_rx) + temp <<= 16; + if (is_rndis) + value |= temp; + else + value &= ~temp; + musb_writel(tibase, DAVINCI_RNDIS_REG, value); + c->is_rndis = is_rndis; + } +} + +static void cppi_dump_rxbd(const char *tag, struct cppi_descriptor *bd) +{ + pr_debug("RXBD/%s %08x: " + "nxt %08x buf %08x off.blen %08x opt.plen %08x\n", + tag, bd->dma, + bd->hw_next, bd->hw_bufp, bd->hw_off_len, + bd->hw_options); +} + +static void cppi_dump_rxq(int level, const char *tag, struct cppi_channel *rx) +{ +#if MUSB_DEBUG > 0 + struct cppi_descriptor *bd; + + if (!_dbg_level(level)) + return; + cppi_dump_rx(level, rx, tag); + if (rx->last_processed) + cppi_dump_rxbd("last", rx->last_processed); + for (bd = rx->head; bd; bd = bd->next) + cppi_dump_rxbd("active", bd); +#endif +} + + +/* NOTE: DaVinci autoreq is ignored except for host side "RNDIS" mode RX; + * so we won't ever use it (see "CPPI RX Woes" below). + */ +static inline int cppi_autoreq_update(struct cppi_channel *rx, + void __iomem *tibase, int onepacket, unsigned n_bds) +{ + u32 val; + +#ifdef RNDIS_RX_IS_USABLE + u32 tmp; + /* assert(is_host_active(musb)) */ + + /* start from "AutoReq never" */ + tmp = musb_readl(tibase, DAVINCI_AUTOREQ_REG); + val = tmp & ~((0x3) << (rx->index * 2)); + + /* HCD arranged reqpkt for packet #1. we arrange int + * for all but the last one, maybe in two segments. + */ + if (!onepacket) { +#if 0 + /* use two segments, autoreq "all" then the last "never" */ + val |= ((0x3) << (rx->index * 2)); + n_bds--; +#else + /* one segment, autoreq "all-but-last" */ + val |= ((0x1) << (rx->index * 2)); +#endif + } + + if (val != tmp) { + int n = 100; + + /* make sure that autoreq is updated before continuing */ + musb_writel(tibase, DAVINCI_AUTOREQ_REG, val); + do { + tmp = musb_readl(tibase, DAVINCI_AUTOREQ_REG); + if (tmp == val) + break; + cpu_relax(); + } while (n-- > 0); + } +#endif + + /* REQPKT is turned off after each segment */ + if (n_bds && rx->channel.actual_len) { + void __iomem *regs = rx->hw_ep->regs; + + val = musb_readw(regs, MUSB_RXCSR); + if (!(val & MUSB_RXCSR_H_REQPKT)) { + val |= MUSB_RXCSR_H_REQPKT | MUSB_RXCSR_H_WZC_BITS; + musb_writew(regs, MUSB_RXCSR, val); + /* flush writebufer */ + val = musb_readw(regs, MUSB_RXCSR); + } + } + return n_bds; +} + + +/* Buffer enqueuing Logic: + * + * - RX builds new queues each time, to help handle routine "early + * termination" cases (faults, including errors and short reads) + * more correctly. + * + * - for now, TX reuses the same queue of BDs every time + * + * REVISIT long term, we want a normal dynamic model. + * ... the goal will be to append to the + * existing queue, processing completed "dma buffers" (segments) on the fly. + * + * Otherwise we force an IRQ latency between requests, which slows us a lot + * (especially in "transparent" dma). Unfortunately that model seems to be + * inherent in the DMA model from the Mentor code, except in the rare case + * of transfers big enough (~128+ KB) that we could append "middle" segments + * in the TX paths. (RX can't do this, see below.) + * + * That's true even in the CPPI- friendly iso case, where most urbs have + * several small segments provided in a group and where the "packet at a time" + * "transparent" DMA model is always correct, even on the RX side. + */ + +/* + * CPPI TX: + * ======== + * TX is a lot more reasonable than RX; it doesn't need to run in + * irq-per-packet mode very often. RNDIS mode seems to behave too + * (except how it handles the exactly-N-packets case). Building a + * txdma queue with multiple requests (urb or usb_request) looks + * like it would work ... but fault handling would need much testing. + * + * The main issue with TX mode RNDIS relates to transfer lengths that + * are an exact multiple of the packet length. It appears that there's + * a hiccup in that case (maybe the DMA completes before the ZLP gets + * written?) boiling down to not being able to rely on CPPI writing any + * terminating zero length packet before the next transfer is written. + * So that's punted to PIO; better yet, gadget drivers can avoid it. + * + * Plus, there's allegedly an undocumented constraint that rndis transfer + * length be a multiple of 64 bytes ... but the chip doesn't act that + * way, and we really don't _want_ that behavior anyway. + * + * On TX, "transparent" mode works ... although experiments have shown + * problems trying to use the SOP/EOP bits in different USB packets. + * + * REVISIT try to handle terminating zero length packets using CPPI + * instead of doing it by PIO after an IRQ. (Meanwhile, make Ethernet + * links avoid that issue by forcing them to avoid zlps.) + */ +static void +cppi_next_tx_segment(struct musb *musb, struct cppi_channel *tx) +{ + unsigned maxpacket = tx->maxpacket; + dma_addr_t addr = tx->buf_dma + tx->offset; + size_t length = tx->buf_len - tx->offset; + struct cppi_descriptor *bd; + unsigned n_bds; + unsigned i; + struct cppi_tx_stateram __iomem *tx_ram = tx->state_ram; + int rndis; + + /* TX can use the CPPI "rndis" mode, where we can probably fit this + * transfer in one BD and one IRQ. The only time we would NOT want + * to use it is when hardware constraints prevent it, or if we'd + * trigger the "send a ZLP?" confusion. + */ + rndis = (maxpacket & 0x3f) == 0 + && length < 0xffff + && (length % maxpacket) != 0; + + if (rndis) { + maxpacket = length; + n_bds = 1; + } else { + n_bds = length / maxpacket; + if (!length || (length % maxpacket)) + n_bds++; + n_bds = min(n_bds, (unsigned) NUM_TXCHAN_BD); + length = min(n_bds * maxpacket, length); + } + + DBG(4, "TX DMA%d, pktSz %d %s bds %d dma 0x%x len %u\n", + tx->index, + maxpacket, + rndis ? "rndis" : "transparent", + n_bds, + addr, length); + + cppi_rndis_update(tx, 0, musb->ctrl_base, rndis); + + /* assuming here that channel_program is called during + * transfer initiation ... current code maintains state + * for one outstanding request only (no queues, not even + * the implicit ones of an iso urb). + */ + + bd = tx->freelist; + tx->head = bd; + tx->last_processed = NULL; + + /* FIXME use BD pool like RX side does, and just queue + * the minimum number for this request. + */ + + /* Prepare queue of BDs first, then hand it to hardware. + * All BDs except maybe the last should be of full packet + * size; for RNDIS there _is_ only that last packet. + */ + for (i = 0; i < n_bds; ) { + if (++i < n_bds && bd->next) + bd->hw_next = bd->next->dma; + else + bd->hw_next = 0; + + bd->hw_bufp = tx->buf_dma + tx->offset; + + /* FIXME set EOP only on the last packet, + * SOP only on the first ... avoid IRQs + */ + if ((tx->offset + maxpacket) <= tx->buf_len) { + tx->offset += maxpacket; + bd->hw_off_len = maxpacket; + bd->hw_options = CPPI_SOP_SET | CPPI_EOP_SET + | CPPI_OWN_SET | maxpacket; + } else { + /* only this one may be a partial USB Packet */ + u32 partial_len; + + partial_len = tx->buf_len - tx->offset; + tx->offset = tx->buf_len; + bd->hw_off_len = partial_len; + + bd->hw_options = CPPI_SOP_SET | CPPI_EOP_SET + | CPPI_OWN_SET | partial_len; + if (partial_len == 0) + bd->hw_options |= CPPI_ZERO_SET; + } + + DBG(5, "TXBD %p: nxt %08x buf %08x len %04x opt %08x\n", + bd, bd->hw_next, bd->hw_bufp, + bd->hw_off_len, bd->hw_options); + + /* update the last BD enqueued to the list */ + tx->tail = bd; + bd = bd->next; + } + + /* BDs live in DMA-coherent memory, but writes might be pending */ + cpu_drain_writebuffer(); + + /* Write to the HeadPtr in state RAM to trigger */ + musb_writel(&tx_ram->tx_head, 0, (u32)tx->freelist->dma); + + cppi_dump_tx(5, tx, "/S"); +} + +/* + * CPPI RX Woes: + * ============= + * Consider a 1KB bulk RX buffer in two scenarios: (a) it's fed two 300 byte + * packets back-to-back, and (b) it's fed two 512 byte packets back-to-back. + * (Full speed transfers have similar scenarios.) + * + * The correct behavior for Linux is that (a) fills the buffer with 300 bytes, + * and the next packet goes into a buffer that's queued later; while (b) fills + * the buffer with 1024 bytes. How to do that with CPPI? + * + * - RX queues in "rndis" mode -- one single BD -- handle (a) correctly, but + * (b) loses **BADLY** because nothing (!) happens when that second packet + * fills the buffer, much less when a third one arrives. (Which makes this + * not a "true" RNDIS mode. In the RNDIS protocol short-packet termination + * is optional, and it's fine if peripherals -- not hosts! -- pad messages + * out to end-of-buffer. Standard PCI host controller DMA descriptors + * implement that mode by default ... which is no accident.) + * + * - RX queues in "transparent" mode -- two BDs with 512 bytes each -- have + * converse problems: (b) is handled right, but (a) loses badly. CPPI RX + * ignores SOP/EOP markings and processes both of those BDs; so both packets + * are loaded into the buffer (with a 212 byte gap between them), and the next + * buffer queued will NOT get its 300 bytes of data. (It seems like SOP/EOP + * are intended as outputs for RX queues, not inputs...) + * + * - A variant of "transparent" mode -- one BD at a time -- is the only way to + * reliably make both cases work, with software handling both cases correctly + * and at the significant penalty of needing an IRQ per packet. (The lack of + * I/O overlap can be slightly ameliorated by enabling double buffering.) + * + * So how to get rid of IRQ-per-packet? The transparent multi-BD case could + * be used in special cases like mass storage, which sets URB_SHORT_NOT_OK + * (or maybe its peripheral side counterpart) to flag (a) scenarios as errors + * with guaranteed driver level fault recovery and scrubbing out what's left + * of that garbaged datastream. + * + * But there seems to be no way to identify the cases where CPPI RNDIS mode + * is appropriate -- which do NOT include RNDIS host drivers, but do include + * the CDC Ethernet driver! -- and the documentation is incomplete/wrong. + * So we can't _ever_ use RX RNDIS mode ... except by using a heuristic + * that applies best on the peripheral side (and which could fail rudely). + * + * Leaving only "transparent" mode; we avoid multi-bd modes in almost all + * cases other than mass storage class. Otherwise we're correct but slow, + * since CPPI penalizes our need for a "true RNDIS" default mode. + */ + + +/* Heuristic, intended to kick in for ethernet/rndis peripheral ONLY + * + * IFF + * (a) peripheral mode ... since rndis peripherals could pad their + * writes to hosts, causing i/o failure; or we'd have to cope with + * a largely unknowable variety of host side protocol variants + * (b) and short reads are NOT errors ... since full reads would + * cause those same i/o failures + * (c) and read length is + * - less than 64KB (max per cppi descriptor) + * - not a multiple of 4096 (g_zero default, full reads typical) + * - N (>1) packets long, ditto (full reads not EXPECTED) + * THEN + * try rx rndis mode + * + * Cost of heuristic failing: RXDMA wedges at the end of transfers that + * fill out the whole buffer. Buggy host side usb network drivers could + * trigger that, but "in the field" such bugs seem to be all but unknown. + * + * So this module parameter lets the heuristic be disabled. When using + * gadgetfs, the heuristic will probably need to be disabled. + */ +static int cppi_rx_rndis = 1; + +module_param(cppi_rx_rndis, bool, 0); +MODULE_PARM_DESC(cppi_rx_rndis, "enable/disable RX RNDIS heuristic"); + + +/** + * cppi_next_rx_segment - dma read for the next chunk of a buffer + * @musb: the controller + * @rx: dma channel + * @onepacket: true unless caller treats short reads as errors, and + * performs fault recovery above usbcore. + * Context: controller irqlocked + * + * See above notes about why we can't use multi-BD RX queues except in + * rare cases (mass storage class), and can never use the hardware "rndis" + * mode (since it's not a "true" RNDIS mode) with complete safety.. + * + * It's ESSENTIAL that callers specify "onepacket" mode unless they kick in + * code to recover from corrupted datastreams after each short transfer. + */ +static void +cppi_next_rx_segment(struct musb *musb, struct cppi_channel *rx, int onepacket) +{ + unsigned maxpacket = rx->maxpacket; + dma_addr_t addr = rx->buf_dma + rx->offset; + size_t length = rx->buf_len - rx->offset; + struct cppi_descriptor *bd, *tail; + unsigned n_bds; + unsigned i; + void __iomem *tibase = musb->ctrl_base; + int is_rndis = 0; + struct cppi_rx_stateram __iomem *rx_ram = rx->state_ram; + + if (onepacket) { + /* almost every USB driver, host or peripheral side */ + n_bds = 1; + + /* maybe apply the heuristic above */ + if (cppi_rx_rndis + && is_peripheral_active(musb) + && length > maxpacket + && (length & ~0xffff) == 0 + && (length & 0x0fff) != 0 + && (length & (maxpacket - 1)) == 0) { + maxpacket = length; + is_rndis = 1; + } + } else { + /* virtually nothing except mass storage class */ + if (length > 0xffff) { + n_bds = 0xffff / maxpacket; + length = n_bds * maxpacket; + } else { + n_bds = length / maxpacket; + if (length % maxpacket) + n_bds++; + } + if (n_bds == 1) + onepacket = 1; + else + n_bds = min(n_bds, (unsigned) NUM_RXCHAN_BD); + } + + /* In host mode, autorequest logic can generate some IN tokens; it's + * tricky since we can't leave REQPKT set in RXCSR after the transfer + * finishes. So: multipacket transfers involve two or more segments. + * And always at least two IRQs ... RNDIS mode is not an option. + */ + if (is_host_active(musb)) + n_bds = cppi_autoreq_update(rx, tibase, onepacket, n_bds); + + cppi_rndis_update(rx, 1, musb->ctrl_base, is_rndis); + + length = min(n_bds * maxpacket, length); + + DBG(4, "RX DMA%d seg, maxp %d %s bds %d (cnt %d) " + "dma 0x%x len %u %u/%u\n", + rx->index, maxpacket, + onepacket + ? (is_rndis ? "rndis" : "onepacket") + : "multipacket", + n_bds, + musb_readl(tibase, + DAVINCI_RXCPPI_BUFCNT0_REG + (rx->index * 4)) + & 0xffff, + addr, length, rx->channel.actual_len, rx->buf_len); + + /* only queue one segment at a time, since the hardware prevents + * correct queue shutdown after unexpected short packets + */ + bd = cppi_bd_alloc(rx); + rx->head = bd; + + /* Build BDs for all packets in this segment */ + for (i = 0, tail = NULL; bd && i < n_bds; i++, tail = bd) { + u32 bd_len; + + if (i) { + bd = cppi_bd_alloc(rx); + if (!bd) + break; + tail->next = bd; + tail->hw_next = bd->dma; + } + bd->hw_next = 0; + + /* all but the last packet will be maxpacket size */ + if (maxpacket < length) + bd_len = maxpacket; + else + bd_len = length; + + bd->hw_bufp = addr; + addr += bd_len; + rx->offset += bd_len; + + bd->hw_off_len = (0 /*offset*/ << 16) + bd_len; + bd->buflen = bd_len; + + bd->hw_options = CPPI_OWN_SET | (i == 0 ? length : 0); + length -= bd_len; + } + + /* we always expect at least one reusable BD! */ + if (!tail) { + WARNING("rx dma%d -- no BDs? need %d\n", rx->index, n_bds); + return; + } else if (i < n_bds) + WARNING("rx dma%d -- only %d of %d BDs\n", rx->index, i, n_bds); + + tail->next = NULL; + tail->hw_next = 0; + + bd = rx->head; + rx->tail = tail; + + /* short reads and other faults should terminate this entire + * dma segment. we want one "dma packet" per dma segment, not + * one per USB packet, terminating the whole queue at once... + * NOTE that current hardware seems to ignore SOP and EOP. + */ + bd->hw_options |= CPPI_SOP_SET; + tail->hw_options |= CPPI_EOP_SET; + + if (debug >= 5) { + struct cppi_descriptor *d; + + for (d = rx->head; d; d = d->next) + cppi_dump_rxbd("S", d); + } + + /* in case the preceding transfer left some state... */ + tail = rx->last_processed; + if (tail) { + tail->next = bd; + tail->hw_next = bd->dma; + } + + core_rxirq_enable(tibase, rx->index + 1); + + /* BDs live in DMA-coherent memory, but writes might be pending */ + cpu_drain_writebuffer(); + + /* REVISIT specs say to write this AFTER the BUFCNT register + * below ... but that loses badly. + */ + musb_writel(&rx_ram->rx_head, 0, bd->dma); + + /* bufferCount must be at least 3, and zeroes on completion + * unless it underflows below zero, or stops at two, or keeps + * growing ... grr. + */ + i = musb_readl(tibase, + DAVINCI_RXCPPI_BUFCNT0_REG + (rx->index * 4)) + & 0xffff; + + if (!i) + musb_writel(tibase, + DAVINCI_RXCPPI_BUFCNT0_REG + (rx->index * 4), + n_bds + 2); + else if (n_bds > (i - 3)) + musb_writel(tibase, + DAVINCI_RXCPPI_BUFCNT0_REG + (rx->index * 4), + n_bds - (i - 3)); + + i = musb_readl(tibase, + DAVINCI_RXCPPI_BUFCNT0_REG + (rx->index * 4)) + & 0xffff; + if (i < (2 + n_bds)) { + DBG(2, "bufcnt%d underrun - %d (for %d)\n", + rx->index, i, n_bds); + musb_writel(tibase, + DAVINCI_RXCPPI_BUFCNT0_REG + (rx->index * 4), + n_bds + 2); + } + + cppi_dump_rx(4, rx, "/S"); +} + +/** + * cppi_channel_program - program channel for data transfer + * @ch: the channel + * @maxpacket: max packet size + * @mode: For RX, 1 unless the usb protocol driver promised to treat + * all short reads as errors and kick in high level fault recovery. + * For TX, ignored because of RNDIS mode races/glitches. + * @dma_addr: dma address of buffer + * @len: length of buffer + * Context: controller irqlocked + */ +static int cppi_channel_program(struct dma_channel *ch, + u16 maxpacket, u8 mode, + dma_addr_t dma_addr, u32 len) +{ + struct cppi_channel *cppi_ch; + struct cppi *controller; + struct musb *musb; + + cppi_ch = container_of(ch, struct cppi_channel, channel); + controller = cppi_ch->controller; + musb = controller->musb; + + switch (ch->status) { + case MUSB_DMA_STATUS_BUS_ABORT: + case MUSB_DMA_STATUS_CORE_ABORT: + /* fault irq handler should have handled cleanup */ + WARNING("%cX DMA%d not cleaned up after abort!\n", + cppi_ch->transmit ? 'T' : 'R', + cppi_ch->index); + /* WARN_ON(1); */ + break; + case MUSB_DMA_STATUS_BUSY: + WARNING("program active channel? %cX DMA%d\n", + cppi_ch->transmit ? 'T' : 'R', + cppi_ch->index); + /* WARN_ON(1); */ + break; + case MUSB_DMA_STATUS_UNKNOWN: + DBG(1, "%cX DMA%d not allocated!\n", + cppi_ch->transmit ? 'T' : 'R', + cppi_ch->index); + /* FALLTHROUGH */ + case MUSB_DMA_STATUS_FREE: + break; + } + + ch->status = MUSB_DMA_STATUS_BUSY; + + /* set transfer parameters, then queue up its first segment */ + cppi_ch->buf_dma = dma_addr; + cppi_ch->offset = 0; + cppi_ch->maxpacket = maxpacket; + cppi_ch->buf_len = len; + + /* TX channel? or RX? */ + if (cppi_ch->transmit) + cppi_next_tx_segment(musb, cppi_ch); + else + cppi_next_rx_segment(musb, cppi_ch, mode); + + return true; +} + +static bool cppi_rx_scan(struct cppi *cppi, unsigned ch) +{ + struct cppi_channel *rx = &cppi->rx[ch]; + struct cppi_rx_stateram __iomem *state = rx->state_ram; + struct cppi_descriptor *bd; + struct cppi_descriptor *last = rx->last_processed; + bool completed = false; + bool acked = false; + int i; + dma_addr_t safe2ack; + void __iomem *regs = rx->hw_ep->regs; + + cppi_dump_rx(6, rx, "/K"); + + bd = last ? last->next : rx->head; + if (!bd) + return false; + + /* run through all completed BDs */ + for (i = 0, safe2ack = musb_readl(&state->rx_complete, 0); + (safe2ack || completed) && bd && i < NUM_RXCHAN_BD; + i++, bd = bd->next) { + u16 len; + + /* catch latest BD writes from CPPI */ + rmb(); + if (!completed && (bd->hw_options & CPPI_OWN_SET)) + break; + + DBG(5, "C/RXBD %08x: nxt %08x buf %08x " + "off.len %08x opt.len %08x (%d)\n", + bd->dma, bd->hw_next, bd->hw_bufp, + bd->hw_off_len, bd->hw_options, + rx->channel.actual_len); + + /* actual packet received length */ + if ((bd->hw_options & CPPI_SOP_SET) && !completed) + len = bd->hw_off_len & CPPI_RECV_PKTLEN_MASK; + else + len = 0; + + if (bd->hw_options & CPPI_EOQ_MASK) + completed = true; + + if (!completed && len < bd->buflen) { + /* NOTE: when we get a short packet, RXCSR_H_REQPKT + * must have been cleared, and no more DMA packets may + * active be in the queue... TI docs didn't say, but + * CPPI ignores those BDs even though OWN is still set. + */ + completed = true; + DBG(3, "rx short %d/%d (%d)\n", + len, bd->buflen, + rx->channel.actual_len); + } + + /* If we got here, we expect to ack at least one BD; meanwhile + * CPPI may completing other BDs while we scan this list... + * + * RACE: we can notice OWN cleared before CPPI raises the + * matching irq by writing that BD as the completion pointer. + * In such cases, stop scanning and wait for the irq, avoiding + * lost acks and states where BD ownership is unclear. + */ + if (bd->dma == safe2ack) { + musb_writel(&state->rx_complete, 0, safe2ack); + safe2ack = musb_readl(&state->rx_complete, 0); + acked = true; + if (bd->dma == safe2ack) + safe2ack = 0; + } + + rx->channel.actual_len += len; + + cppi_bd_free(rx, last); + last = bd; + + /* stop scanning on end-of-segment */ + if (bd->hw_next == 0) + completed = true; + } + rx->last_processed = last; + + /* dma abort, lost ack, or ... */ + if (!acked && last) { + int csr; + + if (safe2ack == 0 || safe2ack == rx->last_processed->dma) + musb_writel(&state->rx_complete, 0, safe2ack); + if (safe2ack == 0) { + cppi_bd_free(rx, last); + rx->last_processed = NULL; + + /* if we land here on the host side, H_REQPKT will + * be clear and we need to restart the queue... + */ + WARN_ON(rx->head); + } + musb_ep_select(cppi->mregs, rx->index + 1); + csr = musb_readw(regs, MUSB_RXCSR); + if (csr & MUSB_RXCSR_DMAENAB) { + DBG(4, "list%d %p/%p, last %08x%s, csr %04x\n", + rx->index, + rx->head, rx->tail, + rx->last_processed + ? rx->last_processed->dma + : 0, + completed ? ", completed" : "", + csr); + cppi_dump_rxq(4, "/what?", rx); + } + } + if (!completed) { + int csr; + + rx->head = bd; + + /* REVISIT seems like "autoreq all but EOP" doesn't... + * setting it here "should" be racey, but seems to work + */ + csr = musb_readw(rx->hw_ep->regs, MUSB_RXCSR); + if (is_host_active(cppi->musb) + && bd + && !(csr & MUSB_RXCSR_H_REQPKT)) { + csr |= MUSB_RXCSR_H_REQPKT; + musb_writew(regs, MUSB_RXCSR, + MUSB_RXCSR_H_WZC_BITS | csr); + csr = musb_readw(rx->hw_ep->regs, MUSB_RXCSR); + } + } else { + rx->head = NULL; + rx->tail = NULL; + } + + cppi_dump_rx(6, rx, completed ? "/completed" : "/cleaned"); + return completed; +} + +void cppi_completion(struct musb *musb, u32 rx, u32 tx) +{ + void __iomem *tibase; + int i, index; + struct cppi *cppi; + struct musb_hw_ep *hw_ep = NULL; + + cppi = container_of(musb->dma_controller, struct cppi, controller); + + tibase = musb->ctrl_base; + + /* process TX channels */ + for (index = 0; tx; tx = tx >> 1, index++) { + struct cppi_channel *tx_ch; + struct cppi_tx_stateram __iomem *tx_ram; + bool completed = false; + struct cppi_descriptor *bd; + + if (!(tx & 1)) + continue; + + tx_ch = cppi->tx + index; + tx_ram = tx_ch->state_ram; + + /* FIXME need a cppi_tx_scan() routine, which + * can also be called from abort code + */ + + cppi_dump_tx(5, tx_ch, "/E"); + + bd = tx_ch->head; + + if (NULL == bd) { + DBG(1, "null BD\n"); + continue; + } + + /* run through all completed BDs */ + for (i = 0; !completed && bd && i < NUM_TXCHAN_BD; + i++, bd = bd->next) { + u16 len; + + /* catch latest BD writes from CPPI */ + rmb(); + if (bd->hw_options & CPPI_OWN_SET) + break; + + DBG(5, "C/TXBD %p n %x b %x off %x opt %x\n", + bd, bd->hw_next, bd->hw_bufp, + bd->hw_off_len, bd->hw_options); + + len = bd->hw_off_len & CPPI_BUFFER_LEN_MASK; + tx_ch->channel.actual_len += len; + + tx_ch->last_processed = bd; + + /* write completion register to acknowledge + * processing of completed BDs, and possibly + * release the IRQ; EOQ might not be set ... + * + * REVISIT use the same ack strategy as rx + * + * REVISIT have observed bit 18 set; huh?? + */ + /* if ((bd->hw_options & CPPI_EOQ_MASK)) */ + musb_writel(&tx_ram->tx_complete, 0, bd->dma); + + /* stop scanning on end-of-segment */ + if (bd->hw_next == 0) + completed = true; + } + + /* on end of segment, maybe go to next one */ + if (completed) { + /* cppi_dump_tx(4, tx_ch, "/complete"); */ + + /* transfer more, or report completion */ + if (tx_ch->offset >= tx_ch->buf_len) { + tx_ch->head = NULL; + tx_ch->tail = NULL; + tx_ch->channel.status = MUSB_DMA_STATUS_FREE; + + hw_ep = tx_ch->hw_ep; + + /* Peripheral role never repurposes the + * endpoint, so immediate completion is + * safe. Host role waits for the fifo + * to empty (TXPKTRDY irq) before going + * to the next queued bulk transfer. + */ + if (is_host_active(cppi->musb)) { +#if 0 + /* WORKAROUND because we may + * not always get TXKPTRDY ... + */ + int csr; + + csr = musb_readw(hw_ep->regs, + MUSB_TXCSR); + if (csr & MUSB_TXCSR_TXPKTRDY) +#endif + completed = false; + } + if (completed) + musb_dma_completion(musb, index + 1, 1); + + } else { + /* Bigger transfer than we could fit in + * that first batch of descriptors... + */ + cppi_next_tx_segment(musb, tx_ch); + } + } else + tx_ch->head = bd; + } + + /* Start processing the RX block */ + for (index = 0; rx; rx = rx >> 1, index++) { + + if (rx & 1) { + struct cppi_channel *rx_ch; + + rx_ch = cppi->rx + index; + + /* let incomplete dma segments finish */ + if (!cppi_rx_scan(cppi, index)) + continue; + + /* start another dma segment if needed */ + if (rx_ch->channel.actual_len != rx_ch->buf_len + && rx_ch->channel.actual_len + == rx_ch->offset) { + cppi_next_rx_segment(musb, rx_ch, 1); + continue; + } + + /* all segments completed! */ + rx_ch->channel.status = MUSB_DMA_STATUS_FREE; + + hw_ep = rx_ch->hw_ep; + + core_rxirq_disable(tibase, index + 1); + musb_dma_completion(musb, index + 1, 0); + } + } + + /* write to CPPI EOI register to re-enable interrupts */ + musb_writel(tibase, DAVINCI_CPPI_EOI_REG, 0); +} + +/* Instantiate a software object representing a DMA controller. */ +struct dma_controller *__init +dma_controller_create(struct musb *musb, void __iomem *mregs) +{ + struct cppi *controller; + + controller = kzalloc(sizeof *controller, GFP_KERNEL); + if (!controller) + return NULL; + + controller->mregs = mregs; + controller->tibase = mregs - DAVINCI_BASE_OFFSET; + + controller->musb = musb; + controller->controller.start = cppi_controller_start; + controller->controller.stop = cppi_controller_stop; + controller->controller.channel_alloc = cppi_channel_allocate; + controller->controller.channel_release = cppi_channel_release; + controller->controller.channel_program = cppi_channel_program; + controller->controller.channel_abort = cppi_channel_abort; + + /* NOTE: allocating from on-chip SRAM would give the least + * contention for memory access, if that ever matters here. + */ + + /* setup BufferPool */ + controller->pool = dma_pool_create("cppi", + controller->musb->controller, + sizeof(struct cppi_descriptor), + CPPI_DESCRIPTOR_ALIGN, 0); + if (!controller->pool) { + kfree(controller); + return NULL; + } + + return &controller->controller; +} + +/* + * Destroy a previously-instantiated DMA controller. + */ +void dma_controller_destroy(struct dma_controller *c) +{ + struct cppi *cppi; + + cppi = container_of(c, struct cppi, controller); + + /* assert: caller stopped the controller first */ + dma_pool_destroy(cppi->pool); + + kfree(cppi); +} + +/* + * Context: controller irqlocked, endpoint selected + */ +static int cppi_channel_abort(struct dma_channel *channel) +{ + struct cppi_channel *cppi_ch; + struct cppi *controller; + void __iomem *mbase; + void __iomem *tibase; + void __iomem *regs; + u32 value; + struct cppi_descriptor *queue; + + cppi_ch = container_of(channel, struct cppi_channel, channel); + + controller = cppi_ch->controller; + + switch (channel->status) { + case MUSB_DMA_STATUS_BUS_ABORT: + case MUSB_DMA_STATUS_CORE_ABORT: + /* from RX or TX fault irq handler */ + case MUSB_DMA_STATUS_BUSY: + /* the hardware needs shutting down */ + regs = cppi_ch->hw_ep->regs; + break; + case MUSB_DMA_STATUS_UNKNOWN: + case MUSB_DMA_STATUS_FREE: + return 0; + default: + return -EINVAL; + } + + if (!cppi_ch->transmit && cppi_ch->head) + cppi_dump_rxq(3, "/abort", cppi_ch); + + mbase = controller->mregs; + tibase = controller->tibase; + + queue = cppi_ch->head; + cppi_ch->head = NULL; + cppi_ch->tail = NULL; + + /* REVISIT should rely on caller having done this, + * and caller should rely on us not changing it. + * peripheral code is safe ... check host too. + */ + musb_ep_select(mbase, cppi_ch->index + 1); + + if (cppi_ch->transmit) { + struct cppi_tx_stateram __iomem *tx_ram; + int enabled; + + /* mask interrupts raised to signal teardown complete. */ + enabled = musb_readl(tibase, DAVINCI_TXCPPI_INTENAB_REG) + & (1 << cppi_ch->index); + if (enabled) + musb_writel(tibase, DAVINCI_TXCPPI_INTCLR_REG, + (1 << cppi_ch->index)); + + /* REVISIT put timeouts on these controller handshakes */ + + cppi_dump_tx(6, cppi_ch, " (teardown)"); + + /* teardown DMA engine then usb core */ + do { + value = musb_readl(tibase, DAVINCI_TXCPPI_TEAR_REG); + } while (!(value & CPPI_TEAR_READY)); + musb_writel(tibase, DAVINCI_TXCPPI_TEAR_REG, cppi_ch->index); + + tx_ram = cppi_ch->state_ram; + do { + value = musb_readl(&tx_ram->tx_complete, 0); + } while (0xFFFFFFFC != value); + musb_writel(&tx_ram->tx_complete, 0, 0xFFFFFFFC); + + /* FIXME clean up the transfer state ... here? + * the completion routine should get called with + * an appropriate status code. + */ + + value = musb_readw(regs, MUSB_TXCSR); + value &= ~MUSB_TXCSR_DMAENAB; + value |= MUSB_TXCSR_FLUSHFIFO; + musb_writew(regs, MUSB_TXCSR, value); + musb_writew(regs, MUSB_TXCSR, value); + + /* re-enable interrupt */ + if (enabled) + musb_writel(tibase, DAVINCI_TXCPPI_INTENAB_REG, + (1 << cppi_ch->index)); + + /* While we scrub the TX state RAM, ensure that we clean + * up any interrupt that's currently asserted: + * 1. Write to completion Ptr value 0x1(bit 0 set) + * (write back mode) + * 2. Write to completion Ptr value 0x0(bit 0 cleared) + * (compare mode) + * Value written is compared(for bits 31:2) and when + * equal, interrupt is deasserted. + */ + cppi_reset_tx(tx_ram, 1); + musb_writel(&tx_ram->tx_complete, 0, 0); + + cppi_dump_tx(5, cppi_ch, " (done teardown)"); + + /* REVISIT tx side _should_ clean up the same way + * as the RX side ... this does no cleanup at all! + */ + + } else /* RX */ { + u16 csr; + + /* NOTE: docs don't guarantee any of this works ... we + * expect that if the usb core stops telling the cppi core + * to pull more data from it, then it'll be safe to flush + * current RX DMA state iff any pending fifo transfer is done. + */ + + core_rxirq_disable(tibase, cppi_ch->index + 1); + + /* for host, ensure ReqPkt is never set again */ + if (is_host_active(cppi_ch->controller->musb)) { + value = musb_readl(tibase, DAVINCI_AUTOREQ_REG); + value &= ~((0x3) << (cppi_ch->index * 2)); + musb_writel(tibase, DAVINCI_AUTOREQ_REG, value); + } + + csr = musb_readw(regs, MUSB_RXCSR); + + /* for host, clear (just) ReqPkt at end of current packet(s) */ + if (is_host_active(cppi_ch->controller->musb)) { + csr |= MUSB_RXCSR_H_WZC_BITS; + csr &= ~MUSB_RXCSR_H_REQPKT; + } else + csr |= MUSB_RXCSR_P_WZC_BITS; + + /* clear dma enable */ + csr &= ~(MUSB_RXCSR_DMAENAB); + musb_writew(regs, MUSB_RXCSR, csr); + csr = musb_readw(regs, MUSB_RXCSR); + + /* Quiesce: wait for current dma to finish (if not cleanup). + * We can't use bit zero of stateram->rx_sop, since that + * refers to an entire "DMA packet" not just emptying the + * current fifo. Most segments need multiple usb packets. + */ + if (channel->status == MUSB_DMA_STATUS_BUSY) + udelay(50); + + /* scan the current list, reporting any data that was + * transferred and acking any IRQ + */ + cppi_rx_scan(controller, cppi_ch->index); + + /* clobber the existing state once it's idle + * + * NOTE: arguably, we should also wait for all the other + * RX channels to quiesce (how??) and then temporarily + * disable RXCPPI_CTRL_REG ... but it seems that we can + * rely on the controller restarting from state ram, with + * only RXCPPI_BUFCNT state being bogus. BUFCNT will + * correct itself after the next DMA transfer though. + * + * REVISIT does using rndis mode change that? + */ + cppi_reset_rx(cppi_ch->state_ram); + + /* next DMA request _should_ load cppi head ptr */ + + /* ... we don't "free" that list, only mutate it in place. */ + cppi_dump_rx(5, cppi_ch, " (done abort)"); + + /* clean up previously pending bds */ + cppi_bd_free(cppi_ch, cppi_ch->last_processed); + cppi_ch->last_processed = NULL; + + while (queue) { + struct cppi_descriptor *tmp = queue->next; + + cppi_bd_free(cppi_ch, queue); + queue = tmp; + } + } + + channel->status = MUSB_DMA_STATUS_FREE; + cppi_ch->buf_dma = 0; + cppi_ch->offset = 0; + cppi_ch->buf_len = 0; + cppi_ch->maxpacket = 0; + return 0; +} + +/* TBD Queries: + * + * Power Management ... probably turn off cppi during suspend, restart; + * check state ram? Clocking is presumably shared with usb core. + */ diff --git a/drivers/usb/musb/cppi_dma.h b/drivers/usb/musb/cppi_dma.h new file mode 100644 index 00000000000..fc5216b5d2c --- /dev/null +++ b/drivers/usb/musb/cppi_dma.h @@ -0,0 +1,133 @@ +/* Copyright (C) 2005-2006 by Texas Instruments */ + +#ifndef _CPPI_DMA_H_ +#define _CPPI_DMA_H_ + +#include +#include +#include +#include +#include + +#include "musb_dma.h" +#include "musb_core.h" + + +/* FIXME fully isolate CPPI from DaVinci ... the "CPPI generic" registers + * would seem to be shared with the TUSB6020 (over VLYNQ). + */ + +#include "davinci.h" + + +/* CPPI RX/TX state RAM */ + +struct cppi_tx_stateram { + u32 tx_head; /* "DMA packet" head descriptor */ + u32 tx_buf; + u32 tx_current; /* current descriptor */ + u32 tx_buf_current; + u32 tx_info; /* flags, remaining buflen */ + u32 tx_rem_len; + u32 tx_dummy; /* unused */ + u32 tx_complete; +}; + +struct cppi_rx_stateram { + u32 rx_skipbytes; + u32 rx_head; + u32 rx_sop; /* "DMA packet" head descriptor */ + u32 rx_current; /* current descriptor */ + u32 rx_buf_current; + u32 rx_len_len; + u32 rx_cnt_cnt; + u32 rx_complete; +}; + +/* hw_options bits in CPPI buffer descriptors */ +#define CPPI_SOP_SET ((u32)(1 << 31)) +#define CPPI_EOP_SET ((u32)(1 << 30)) +#define CPPI_OWN_SET ((u32)(1 << 29)) /* owned by cppi */ +#define CPPI_EOQ_MASK ((u32)(1 << 28)) +#define CPPI_ZERO_SET ((u32)(1 << 23)) /* rx saw zlp; tx issues one */ +#define CPPI_RXABT_MASK ((u32)(1 << 19)) /* need more rx buffers */ + +#define CPPI_RECV_PKTLEN_MASK 0xFFFF +#define CPPI_BUFFER_LEN_MASK 0xFFFF + +#define CPPI_TEAR_READY ((u32)(1 << 31)) + +/* CPPI data structure definitions */ + +#define CPPI_DESCRIPTOR_ALIGN 16 /* bytes; 5-dec docs say 4-byte align */ + +struct cppi_descriptor { + /* hardware overlay */ + u32 hw_next; /* next buffer descriptor Pointer */ + u32 hw_bufp; /* i/o buffer pointer */ + u32 hw_off_len; /* buffer_offset16, buffer_length16 */ + u32 hw_options; /* flags: SOP, EOP etc*/ + + struct cppi_descriptor *next; + dma_addr_t dma; /* address of this descriptor */ + u32 buflen; /* for RX: original buffer length */ +} __attribute__ ((aligned(CPPI_DESCRIPTOR_ALIGN))); + + +struct cppi; + +/* CPPI Channel Control structure */ +struct cppi_channel { + struct dma_channel channel; + + /* back pointer to the DMA controller structure */ + struct cppi *controller; + + /* which direction of which endpoint? */ + struct musb_hw_ep *hw_ep; + bool transmit; + u8 index; + + /* DMA modes: RNDIS or "transparent" */ + u8 is_rndis; + + /* book keeping for current transfer request */ + dma_addr_t buf_dma; + u32 buf_len; + u32 maxpacket; + u32 offset; /* dma requested */ + + void __iomem *state_ram; /* CPPI state */ + + struct cppi_descriptor *freelist; + + /* BD management fields */ + struct cppi_descriptor *head; + struct cppi_descriptor *tail; + struct cppi_descriptor *last_processed; + + /* use tx_complete in host role to track endpoints waiting for + * FIFONOTEMPTY to clear. + */ + struct list_head tx_complete; +}; + +/* CPPI DMA controller object */ +struct cppi { + struct dma_controller controller; + struct musb *musb; + void __iomem *mregs; /* Mentor regs */ + void __iomem *tibase; /* TI/CPPI regs */ + + struct cppi_channel tx[MUSB_C_NUM_EPT - 1]; + struct cppi_channel rx[MUSB_C_NUM_EPR - 1]; + + struct dma_pool *pool; + + struct list_head tx_complete; +}; + +/* irq handling hook */ +extern void cppi_completion(struct musb *, u32 rx, u32 tx); + +#endif /* end of ifndef _CPPI_DMA_H_ */ diff --git a/drivers/usb/musb/davinci.c b/drivers/usb/musb/davinci.c new file mode 100644 index 00000000000..75baf181a8c --- /dev/null +++ b/drivers/usb/musb/davinci.c @@ -0,0 +1,462 @@ +/* + * Copyright (C) 2005-2006 by Texas Instruments + * + * This file is part of the Inventra Controller Driver for Linux. + * + * The Inventra Controller Driver for Linux is free software; you + * can redistribute it and/or modify it under the terms of the GNU + * General Public License version 2 as published by the Free Software + * Foundation. + * + * The Inventra Controller Driver for Linux is distributed in + * the hope that it will be useful, but WITHOUT ANY WARRANTY; + * without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public + * License for more details. + * + * You should have received a copy of the GNU General Public License + * along with The Inventra Controller Driver for Linux ; if not, + * write to the Free Software Foundation, Inc., 59 Temple Place, + * Suite 330, Boston, MA 02111-1307 USA + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include "musb_core.h" + +#ifdef CONFIG_MACH_DAVINCI_EVM +#include +#endif + +#include "davinci.h" +#include "cppi_dma.h" + + +/* REVISIT (PM) we should be able to keep the PHY in low power mode most + * of the time (24 MHZ oscillator and PLL off, etc) by setting POWER.D0 + * and, when in host mode, autosuspending idle root ports... PHYPLLON + * (overriding SUSPENDM?) then likely needs to stay off. + */ + +static inline void phy_on(void) +{ + /* start the on-chip PHY and its PLL */ + __raw_writel(USBPHY_SESNDEN | USBPHY_VBDTCTEN | USBPHY_PHYPLLON, + (void __force __iomem *) IO_ADDRESS(USBPHY_CTL_PADDR)); + while ((__raw_readl((void __force __iomem *) + IO_ADDRESS(USBPHY_CTL_PADDR)) + & USBPHY_PHYCLKGD) == 0) + cpu_relax(); +} + +static inline void phy_off(void) +{ + /* powerdown the on-chip PHY and its oscillator */ + __raw_writel(USBPHY_OSCPDWN | USBPHY_PHYPDWN, (void __force __iomem *) + IO_ADDRESS(USBPHY_CTL_PADDR)); +} + +static int dma_off = 1; + +void musb_platform_enable(struct musb *musb) +{ + u32 tmp, old, val; + + /* workaround: setup irqs through both register sets */ + tmp = (musb->epmask & DAVINCI_USB_TX_ENDPTS_MASK) + << DAVINCI_USB_TXINT_SHIFT; + musb_writel(musb->ctrl_base, DAVINCI_USB_INT_MASK_SET_REG, tmp); + old = tmp; + tmp = (musb->epmask & (0xfffe & DAVINCI_USB_RX_ENDPTS_MASK)) + << DAVINCI_USB_RXINT_SHIFT; + musb_writel(musb->ctrl_base, DAVINCI_USB_INT_MASK_SET_REG, tmp); + tmp |= old; + + val = ~MUSB_INTR_SOF; + tmp |= ((val & 0x01ff) << DAVINCI_USB_USBINT_SHIFT); + musb_writel(musb->ctrl_base, DAVINCI_USB_INT_MASK_SET_REG, tmp); + + if (is_dma_capable() && !dma_off) + printk(KERN_WARNING "%s %s: dma not reactivated\n", + __FILE__, __func__); + else + dma_off = 0; + + /* force a DRVVBUS irq so we can start polling for ID change */ + if (is_otg_enabled(musb)) + musb_writel(musb->ctrl_base, DAVINCI_USB_INT_SET_REG, + DAVINCI_INTR_DRVVBUS << DAVINCI_USB_USBINT_SHIFT); +} + +/* + * Disable the HDRC and flush interrupts + */ +void musb_platform_disable(struct musb *musb) +{ + /* because we don't set CTRLR.UINT, "important" to: + * - not read/write INTRUSB/INTRUSBE + * - (except during initial setup, as workaround) + * - use INTSETR/INTCLRR instead + */ + musb_writel(musb->ctrl_base, DAVINCI_USB_INT_MASK_CLR_REG, + DAVINCI_USB_USBINT_MASK + | DAVINCI_USB_TXINT_MASK + | DAVINCI_USB_RXINT_MASK); + musb_writeb(musb->mregs, MUSB_DEVCTL, 0); + musb_writel(musb->ctrl_base, DAVINCI_USB_EOI_REG, 0); + + if (is_dma_capable() && !dma_off) + WARNING("dma still active\n"); +} + + +/* REVISIT it's not clear whether DaVinci can support full OTG. */ + +static int vbus_state = -1; + +#ifdef CONFIG_USB_MUSB_HDRC_HCD +#define portstate(stmt) stmt +#else +#define portstate(stmt) +#endif + + +/* VBUS SWITCHING IS BOARD-SPECIFIC */ + +#ifdef CONFIG_MACH_DAVINCI_EVM +#ifndef CONFIG_MACH_DAVINCI_EVM_OTG + +/* I2C operations are always synchronous, and require a task context. + * With unloaded systems, using the shared workqueue seems to suffice + * to satisfy the 100msec A_WAIT_VRISE timeout... + */ +static void evm_deferred_drvvbus(struct work_struct *ignored) +{ + davinci_i2c_expander_op(0x3a, USB_DRVVBUS, vbus_state); + vbus_state = !vbus_state; +} +static DECLARE_WORK(evm_vbus_work, evm_deferred_drvvbus); + +#endif /* modified board */ +#endif /* EVM */ + +static void davinci_source_power(struct musb *musb, int is_on, int immediate) +{ + if (is_on) + is_on = 1; + + if (vbus_state == is_on) + return; + vbus_state = !is_on; /* 0/1 vs "-1 == unknown/init" */ + +#ifdef CONFIG_MACH_DAVINCI_EVM + if (machine_is_davinci_evm()) { +#ifdef CONFIG_MACH_DAVINCI_EVM_OTG + /* modified EVM board switching VBUS with GPIO(6) not I2C + * NOTE: PINMUX0.RGB888 (bit23) must be clear + */ + if (is_on) + gpio_set(GPIO(6)); + else + gpio_clear(GPIO(6)); + immediate = 1; +#else + if (immediate) + davinci_i2c_expander_op(0x3a, USB_DRVVBUS, !is_on); + else + schedule_work(&evm_vbus_work); +#endif + } +#endif + if (immediate) + vbus_state = is_on; +} + +static void davinci_set_vbus(struct musb *musb, int is_on) +{ + WARN_ON(is_on && is_peripheral_active(musb)); + davinci_source_power(musb, is_on, 0); +} + + +#define POLL_SECONDS 2 + +static struct timer_list otg_workaround; + +static void otg_timer(unsigned long _musb) +{ + struct musb *musb = (void *)_musb; + void __iomem *mregs = musb->mregs; + u8 devctl; + unsigned long flags; + + /* We poll because DaVinci's won't expose several OTG-critical + * status change events (from the transceiver) otherwise. + */ + devctl = musb_readb(mregs, MUSB_DEVCTL); + DBG(7, "poll devctl %02x (%s)\n", devctl, otg_state_string(musb)); + + spin_lock_irqsave(&musb->lock, flags); + switch (musb->xceiv.state) { + case OTG_STATE_A_WAIT_VFALL: + /* Wait till VBUS falls below SessionEnd (~0.2V); the 1.3 RTL + * seems to mis-handle session "start" otherwise (or in our + * case "recover"), in routine "VBUS was valid by the time + * VBUSERR got reported during enumeration" cases. + */ + if (devctl & MUSB_DEVCTL_VBUS) { + mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ); + break; + } + musb->xceiv.state = OTG_STATE_A_WAIT_VRISE; + musb_writel(musb->ctrl_base, DAVINCI_USB_INT_SET_REG, + MUSB_INTR_VBUSERROR << DAVINCI_USB_USBINT_SHIFT); + break; + case OTG_STATE_B_IDLE: + if (!is_peripheral_enabled(musb)) + break; + + /* There's no ID-changed IRQ, so we have no good way to tell + * when to switch to the A-Default state machine (by setting + * the DEVCTL.SESSION flag). + * + * Workaround: whenever we're in B_IDLE, try setting the + * session flag every few seconds. If it works, ID was + * grounded and we're now in the A-Default state machine. + * + * NOTE setting the session flag is _supposed_ to trigger + * SRP, but clearly it doesn't. + */ + musb_writeb(mregs, MUSB_DEVCTL, + devctl | MUSB_DEVCTL_SESSION); + devctl = musb_readb(mregs, MUSB_DEVCTL); + if (devctl & MUSB_DEVCTL_BDEVICE) + mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ); + else + musb->xceiv.state = OTG_STATE_A_IDLE; + break; + default: + break; + } + spin_unlock_irqrestore(&musb->lock, flags); +} + +static irqreturn_t davinci_interrupt(int irq, void *__hci) +{ + unsigned long flags; + irqreturn_t retval = IRQ_NONE; + struct musb *musb = __hci; + void __iomem *tibase = musb->ctrl_base; + u32 tmp; + + spin_lock_irqsave(&musb->lock, flags); + + /* NOTE: DaVinci shadows the Mentor IRQs. Don't manage them through + * the Mentor registers (except for setup), use the TI ones and EOI. + * + * Docs describe irq "vector" registers asociated with the CPPI and + * USB EOI registers. These hold a bitmask corresponding to the + * current IRQ, not an irq handler address. Would using those bits + * resolve some of the races observed in this dispatch code?? + */ + + /* CPPI interrupts share the same IRQ line, but have their own + * mask, state, "vector", and EOI registers. + */ + if (is_cppi_enabled()) { + u32 cppi_tx = musb_readl(tibase, DAVINCI_TXCPPI_MASKED_REG); + u32 cppi_rx = musb_readl(tibase, DAVINCI_RXCPPI_MASKED_REG); + + if (cppi_tx || cppi_rx) { + DBG(4, "CPPI IRQ t%x r%x\n", cppi_tx, cppi_rx); + cppi_completion(musb, cppi_rx, cppi_tx); + retval = IRQ_HANDLED; + } + } + + /* ack and handle non-CPPI interrupts */ + tmp = musb_readl(tibase, DAVINCI_USB_INT_SRC_MASKED_REG); + musb_writel(tibase, DAVINCI_USB_INT_SRC_CLR_REG, tmp); + DBG(4, "IRQ %08x\n", tmp); + + musb->int_rx = (tmp & DAVINCI_USB_RXINT_MASK) + >> DAVINCI_USB_RXINT_SHIFT; + musb->int_tx = (tmp & DAVINCI_USB_TXINT_MASK) + >> DAVINCI_USB_TXINT_SHIFT; + musb->int_usb = (tmp & DAVINCI_USB_USBINT_MASK) + >> DAVINCI_USB_USBINT_SHIFT; + + /* DRVVBUS irqs are the only proxy we have (a very poor one!) for + * DaVinci's missing ID change IRQ. We need an ID change IRQ to + * switch appropriately between halves of the OTG state machine. + * Managing DEVCTL.SESSION per Mentor docs requires we know its + * value, but DEVCTL.BDEVICE is invalid without DEVCTL.SESSION set. + * Also, DRVVBUS pulses for SRP (but not at 5V) ... + */ + if (tmp & (DAVINCI_INTR_DRVVBUS << DAVINCI_USB_USBINT_SHIFT)) { + int drvvbus = musb_readl(tibase, DAVINCI_USB_STAT_REG); + void __iomem *mregs = musb->mregs; + u8 devctl = musb_readb(mregs, MUSB_DEVCTL); + int err = musb->int_usb & MUSB_INTR_VBUSERROR; + + err = is_host_enabled(musb) + && (musb->int_usb & MUSB_INTR_VBUSERROR); + if (err) { + /* The Mentor core doesn't debounce VBUS as needed + * to cope with device connect current spikes. This + * means it's not uncommon for bus-powered devices + * to get VBUS errors during enumeration. + * + * This is a workaround, but newer RTL from Mentor + * seems to allow a better one: "re"starting sessions + * without waiting (on EVM, a **long** time) for VBUS + * to stop registering in devctl. + */ + musb->int_usb &= ~MUSB_INTR_VBUSERROR; + musb->xceiv.state = OTG_STATE_A_WAIT_VFALL; + mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ); + WARNING("VBUS error workaround (delay coming)\n"); + } else if (is_host_enabled(musb) && drvvbus) { + musb->is_active = 1; + MUSB_HST_MODE(musb); + musb->xceiv.default_a = 1; + musb->xceiv.state = OTG_STATE_A_WAIT_VRISE; + portstate(musb->port1_status |= USB_PORT_STAT_POWER); + del_timer(&otg_workaround); + } else { + musb->is_active = 0; + MUSB_DEV_MODE(musb); + musb->xceiv.default_a = 0; + musb->xceiv.state = OTG_STATE_B_IDLE; + portstate(musb->port1_status &= ~USB_PORT_STAT_POWER); + } + + /* NOTE: this must complete poweron within 100 msec */ + davinci_source_power(musb, drvvbus, 0); + DBG(2, "VBUS %s (%s)%s, devctl %02x\n", + drvvbus ? "on" : "off", + otg_state_string(musb), + err ? " ERROR" : "", + devctl); + retval = IRQ_HANDLED; + } + + if (musb->int_tx || musb->int_rx || musb->int_usb) + retval |= musb_interrupt(musb); + + /* irq stays asserted until EOI is written */ + musb_writel(tibase, DAVINCI_USB_EOI_REG, 0); + + /* poll for ID change */ + if (is_otg_enabled(musb) + && musb->xceiv.state == OTG_STATE_B_IDLE) + mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ); + + spin_unlock_irqrestore(&musb->lock, flags); + + /* REVISIT we sometimes get unhandled IRQs + * (e.g. ep0). not clear why... + */ + if (retval != IRQ_HANDLED) + DBG(5, "unhandled? %08x\n", tmp); + return IRQ_HANDLED; +} + +int __init musb_platform_init(struct musb *musb) +{ + void __iomem *tibase = musb->ctrl_base; + u32 revision; + + musb->mregs += DAVINCI_BASE_OFFSET; +#if 0 + /* REVISIT there's something odd about clocking, this + * didn't appear do the job ... + */ + musb->clock = clk_get(pDevice, "usb"); + if (IS_ERR(musb->clock)) + return PTR_ERR(musb->clock); + + status = clk_enable(musb->clock); + if (status < 0) + return -ENODEV; +#endif + + /* returns zero if e.g. not clocked */ + revision = musb_readl(tibase, DAVINCI_USB_VERSION_REG); + if (revision == 0) + return -ENODEV; + + if (is_host_enabled(musb)) + setup_timer(&otg_workaround, otg_timer, (unsigned long) musb); + + musb->board_set_vbus = davinci_set_vbus; + davinci_source_power(musb, 0, 1); + + /* reset the controller */ + musb_writel(tibase, DAVINCI_USB_CTRL_REG, 0x1); + + /* start the on-chip PHY and its PLL */ + phy_on(); + + msleep(5); + + /* NOTE: irqs are in mixed mode, not bypass to pure-musb */ + pr_debug("DaVinci OTG revision %08x phy %03x control %02x\n", + revision, __raw_readl((void __force __iomem *) + IO_ADDRESS(USBPHY_CTL_PADDR)), + musb_readb(tibase, DAVINCI_USB_CTRL_REG)); + + musb->isr = davinci_interrupt; + return 0; +} + +int musb_platform_exit(struct musb *musb) +{ + if (is_host_enabled(musb)) + del_timer_sync(&otg_workaround); + + davinci_source_power(musb, 0 /*off*/, 1); + + /* delay, to avoid problems with module reload */ + if (is_host_enabled(musb) && musb->xceiv.default_a) { + int maxdelay = 30; + u8 devctl, warn = 0; + + /* if there's no peripheral connected, this can take a + * long time to fall, especially on EVM with huge C133. + */ + do { + devctl = musb_readb(musb->mregs, MUSB_DEVCTL); + if (!(devctl & MUSB_DEVCTL_VBUS)) + break; + if ((devctl & MUSB_DEVCTL_VBUS) != warn) { + warn = devctl & MUSB_DEVCTL_VBUS; + DBG(1, "VBUS %d\n", + warn >> MUSB_DEVCTL_VBUS_SHIFT); + } + msleep(1000); + maxdelay--; + } while (maxdelay > 0); + + /* in OTG mode, another host might be connected */ + if (devctl & MUSB_DEVCTL_VBUS) + DBG(1, "VBUS off timeout (devctl %02x)\n", devctl); + } + + phy_off(); + return 0; +} diff --git a/drivers/usb/musb/davinci.h b/drivers/usb/musb/davinci.h new file mode 100644 index 00000000000..7fb6238e270 --- /dev/null +++ b/drivers/usb/musb/davinci.h @@ -0,0 +1,100 @@ +/* + * Copyright (C) 2005-2006 by Texas Instruments + * + * The Inventra Controller Driver for Linux is free software; you + * can redistribute it and/or modify it under the terms of the GNU + * General Public License version 2 as published by the Free Software + * Foundation. + */ + +#ifndef __MUSB_HDRDF_H__ +#define __MUSB_HDRDF_H__ + +/* + * DaVinci-specific definitions + */ + +/* Integrated highspeed/otg PHY */ +#define USBPHY_CTL_PADDR (DAVINCI_SYSTEM_MODULE_BASE + 0x34) +#define USBPHY_PHYCLKGD (1 << 8) +#define USBPHY_SESNDEN (1 << 7) /* v(sess_end) comparator */ +#define USBPHY_VBDTCTEN (1 << 6) /* v(bus) comparator */ +#define USBPHY_PHYPLLON (1 << 4) /* override pll suspend */ +#define USBPHY_CLKO1SEL (1 << 3) +#define USBPHY_OSCPDWN (1 << 2) +#define USBPHY_PHYPDWN (1 << 0) + +/* For now include usb OTG module registers here */ +#define DAVINCI_USB_VERSION_REG 0x00 +#define DAVINCI_USB_CTRL_REG 0x04 +#define DAVINCI_USB_STAT_REG 0x08 +#define DAVINCI_RNDIS_REG 0x10 +#define DAVINCI_AUTOREQ_REG 0x14 +#define DAVINCI_USB_INT_SOURCE_REG 0x20 +#define DAVINCI_USB_INT_SET_REG 0x24 +#define DAVINCI_USB_INT_SRC_CLR_REG 0x28 +#define DAVINCI_USB_INT_MASK_REG 0x2c +#define DAVINCI_USB_INT_MASK_SET_REG 0x30 +#define DAVINCI_USB_INT_MASK_CLR_REG 0x34 +#define DAVINCI_USB_INT_SRC_MASKED_REG 0x38 +#define DAVINCI_USB_EOI_REG 0x3c +#define DAVINCI_USB_EOI_INTVEC 0x40 + +/* BEGIN CPPI-generic (?) */ + +/* CPPI related registers */ +#define DAVINCI_TXCPPI_CTRL_REG 0x80 +#define DAVINCI_TXCPPI_TEAR_REG 0x84 +#define DAVINCI_CPPI_EOI_REG 0x88 +#define DAVINCI_CPPI_INTVEC_REG 0x8c +#define DAVINCI_TXCPPI_MASKED_REG 0x90 +#define DAVINCI_TXCPPI_RAW_REG 0x94 +#define DAVINCI_TXCPPI_INTENAB_REG 0x98 +#define DAVINCI_TXCPPI_INTCLR_REG 0x9c + +#define DAVINCI_RXCPPI_CTRL_REG 0xC0 +#define DAVINCI_RXCPPI_MASKED_REG 0xD0 +#define DAVINCI_RXCPPI_RAW_REG 0xD4 +#define DAVINCI_RXCPPI_INTENAB_REG 0xD8 +#define DAVINCI_RXCPPI_INTCLR_REG 0xDC + +#define DAVINCI_RXCPPI_BUFCNT0_REG 0xE0 +#define DAVINCI_RXCPPI_BUFCNT1_REG 0xE4 +#define DAVINCI_RXCPPI_BUFCNT2_REG 0xE8 +#define DAVINCI_RXCPPI_BUFCNT3_REG 0xEC + +/* CPPI state RAM entries */ +#define DAVINCI_CPPI_STATERAM_BASE_OFFSET 0x100 + +#define DAVINCI_TXCPPI_STATERAM_OFFSET(chnum) \ + (DAVINCI_CPPI_STATERAM_BASE_OFFSET + ((chnum) * 0x40)) +#define DAVINCI_RXCPPI_STATERAM_OFFSET(chnum) \ + (DAVINCI_CPPI_STATERAM_BASE_OFFSET + 0x20 + ((chnum) * 0x40)) + +/* CPPI masks */ +#define DAVINCI_DMA_CTRL_ENABLE 1 +#define DAVINCI_DMA_CTRL_DISABLE 0 + +#define DAVINCI_DMA_ALL_CHANNELS_ENABLE 0xF +#define DAVINCI_DMA_ALL_CHANNELS_DISABLE 0xF + +/* END CPPI-generic (?) */ + +#define DAVINCI_USB_TX_ENDPTS_MASK 0x1f /* ep0 + 4 tx */ +#define DAVINCI_USB_RX_ENDPTS_MASK 0x1e /* 4 rx */ + +#define DAVINCI_USB_USBINT_SHIFT 16 +#define DAVINCI_USB_TXINT_SHIFT 0 +#define DAVINCI_USB_RXINT_SHIFT 8 + +#define DAVINCI_INTR_DRVVBUS 0x0100 + +#define DAVINCI_USB_USBINT_MASK 0x01ff0000 /* 8 Mentor, DRVVBUS */ +#define DAVINCI_USB_TXINT_MASK \ + (DAVINCI_USB_TX_ENDPTS_MASK << DAVINCI_USB_TXINT_SHIFT) +#define DAVINCI_USB_RXINT_MASK \ + (DAVINCI_USB_RX_ENDPTS_MASK << DAVINCI_USB_RXINT_SHIFT) + +#define DAVINCI_BASE_OFFSET 0x400 + +#endif /* __MUSB_HDRDF_H__ */ diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c new file mode 100644 index 00000000000..462586d06da --- /dev/null +++ b/drivers/usb/musb/musb_core.c @@ -0,0 +1,2266 @@ +/* + * MUSB OTG driver core code + * + * Copyright 2005 Mentor Graphics Corporation + * Copyright (C) 2005-2006 by Texas Instruments + * Copyright (C) 2006-2007 Nokia Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + */ + +/* + * Inventra (Multipoint) Dual-Role Controller Driver for Linux. + * + * This consists of a Host Controller Driver (HCD) and a peripheral + * controller driver implementing the "Gadget" API; OTG support is + * in the works. These are normal Linux-USB controller drivers which + * use IRQs and have no dedicated thread. + * + * This version of the driver has only been used with products from + * Texas Instruments. Those products integrate the Inventra logic + * with other DMA, IRQ, and bus modules, as well as other logic that + * needs to be reflected in this driver. + * + * + * NOTE: the original Mentor code here was pretty much a collection + * of mechanisms that don't seem to have been fully integrated/working + * for *any* Linux kernel version. This version aims at Linux 2.6.now, + * Key open issues include: + * + * - Lack of host-side transaction scheduling, for all transfer types. + * The hardware doesn't do it; instead, software must. + * + * This is not an issue for OTG devices that don't support external + * hubs, but for more "normal" USB hosts it's a user issue that the + * "multipoint" support doesn't scale in the expected ways. That + * includes DaVinci EVM in a common non-OTG mode. + * + * * Control and bulk use dedicated endpoints, and there's as + * yet no mechanism to either (a) reclaim the hardware when + * peripherals are NAKing, which gets complicated with bulk + * endpoints, or (b) use more than a single bulk endpoint in + * each direction. + * + * RESULT: one device may be perceived as blocking another one. + * + * * Interrupt and isochronous will dynamically allocate endpoint + * hardware, but (a) there's no record keeping for bandwidth; + * (b) in the common case that few endpoints are available, there + * is no mechanism to reuse endpoints to talk to multiple devices. + * + * RESULT: At one extreme, bandwidth can be overcommitted in + * some hardware configurations, no faults will be reported. + * At the other extreme, the bandwidth capabilities which do + * exist tend to be severely undercommitted. You can't yet hook + * up both a keyboard and a mouse to an external USB hub. + */ + +/* + * This gets many kinds of configuration information: + * - Kconfig for everything user-configurable + * - for SOC or family details + * - platform_device for addressing, irq, and platform_data + * - platform_data is mostly for board-specific informarion + * + * Most of the conditional compilation will (someday) vanish. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#ifdef CONFIG_ARM +#include +#include +#include +#endif + +#include "musb_core.h" + + +#ifdef CONFIG_ARCH_DAVINCI +#include "davinci.h" +#endif + + + +#if MUSB_DEBUG > 0 +unsigned debug = MUSB_DEBUG; +module_param(debug, uint, 0); +MODULE_PARM_DESC(debug, "initial debug message level"); + +#define MUSB_VERSION_SUFFIX "/dbg" +#endif + +#define DRIVER_AUTHOR "Mentor Graphics, Texas Instruments, Nokia" +#define DRIVER_DESC "Inventra Dual-Role USB Controller Driver" + +#define MUSB_VERSION_BASE "6.0" + +#ifndef MUSB_VERSION_SUFFIX +#define MUSB_VERSION_SUFFIX "" +#endif +#define MUSB_VERSION MUSB_VERSION_BASE MUSB_VERSION_SUFFIX + +#define DRIVER_INFO DRIVER_DESC ", v" MUSB_VERSION + +#define MUSB_DRIVER_NAME "musb_hdrc" +const char musb_driver_name[] = MUSB_DRIVER_NAME; + +MODULE_DESCRIPTION(DRIVER_INFO); +MODULE_AUTHOR(DRIVER_AUTHOR); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:" MUSB_DRIVER_NAME); + + +/*-------------------------------------------------------------------------*/ + +static inline struct musb *dev_to_musb(struct device *dev) +{ +#ifdef CONFIG_USB_MUSB_HDRC_HCD + /* usbcore insists dev->driver_data is a "struct hcd *" */ + return hcd_to_musb(dev_get_drvdata(dev)); +#else + return dev_get_drvdata(dev); +#endif +} + +/*-------------------------------------------------------------------------*/ + +#ifndef CONFIG_USB_TUSB6010 +/* + * Load an endpoint's FIFO + */ +void musb_write_fifo(struct musb_hw_ep *hw_ep, u16 len, const u8 *src) +{ + void __iomem *fifo = hw_ep->fifo; + + prefetch((u8 *)src); + + DBG(4, "%cX ep%d fifo %p count %d buf %p\n", + 'T', hw_ep->epnum, fifo, len, src); + + /* we can't assume unaligned reads work */ + if (likely((0x01 & (unsigned long) src) == 0)) { + u16 index = 0; + + /* best case is 32bit-aligned source address */ + if ((0x02 & (unsigned long) src) == 0) { + if (len >= 4) { + writesl(fifo, src + index, len >> 2); + index += len & ~0x03; + } + if (len & 0x02) { + musb_writew(fifo, 0, *(u16 *)&src[index]); + index += 2; + } + } else { + if (len >= 2) { + writesw(fifo, src + index, len >> 1); + index += len & ~0x01; + } + } + if (len & 0x01) + musb_writeb(fifo, 0, src[index]); + } else { + /* byte aligned */ + writesb(fifo, src, len); + } +} + +/* + * Unload an endpoint's FIFO + */ +void musb_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *dst) +{ + void __iomem *fifo = hw_ep->fifo; + + DBG(4, "%cX ep%d fifo %p count %d buf %p\n", + 'R', hw_ep->epnum, fifo, len, dst); + + /* we can't assume unaligned writes work */ + if (likely((0x01 & (unsigned long) dst) == 0)) { + u16 index = 0; + + /* best case is 32bit-aligned destination address */ + if ((0x02 & (unsigned long) dst) == 0) { + if (len >= 4) { + readsl(fifo, dst, len >> 2); + index = len & ~0x03; + } + if (len & 0x02) { + *(u16 *)&dst[index] = musb_readw(fifo, 0); + index += 2; + } + } else { + if (len >= 2) { + readsw(fifo, dst, len >> 1); + index = len & ~0x01; + } + } + if (len & 0x01) + dst[index] = musb_readb(fifo, 0); + } else { + /* byte aligned */ + readsb(fifo, dst, len); + } +} + +#endif /* normal PIO */ + + +/*-------------------------------------------------------------------------*/ + +/* for high speed test mode; see USB 2.0 spec 7.1.20 */ +static const u8 musb_test_packet[53] = { + /* implicit SYNC then DATA0 to start */ + + /* JKJKJKJK x9 */ + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + /* JJKKJJKK x8 */ + 0xaa, 0xaa, 0xaa, 0xaa, 0xaa, 0xaa, 0xaa, 0xaa, + /* JJJJKKKK x8 */ + 0xee, 0xee, 0xee, 0xee, 0xee, 0xee, 0xee, 0xee, + /* JJJJJJJKKKKKKK x8 */ + 0xfe, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, + /* JJJJJJJK x8 */ + 0x7f, 0xbf, 0xdf, 0xef, 0xf7, 0xfb, 0xfd, + /* JKKKKKKK x10, JK */ + 0xfc, 0x7e, 0xbf, 0xdf, 0xef, 0xf7, 0xfb, 0xfd, 0x7e + + /* implicit CRC16 then EOP to end */ +}; + +void musb_load_testpacket(struct musb *musb) +{ + void __iomem *regs = musb->endpoints[0].regs; + + musb_ep_select(musb->mregs, 0); + musb_write_fifo(musb->control_ep, + sizeof(musb_test_packet), musb_test_packet); + musb_writew(regs, MUSB_CSR0, MUSB_CSR0_TXPKTRDY); +} + +/*-------------------------------------------------------------------------*/ + +const char *otg_state_string(struct musb *musb) +{ + switch (musb->xceiv.state) { + case OTG_STATE_A_IDLE: return "a_idle"; + case OTG_STATE_A_WAIT_VRISE: return "a_wait_vrise"; + case OTG_STATE_A_WAIT_BCON: return "a_wait_bcon"; + case OTG_STATE_A_HOST: return "a_host"; + case OTG_STATE_A_SUSPEND: return "a_suspend"; + case OTG_STATE_A_PERIPHERAL: return "a_peripheral"; + case OTG_STATE_A_WAIT_VFALL: return "a_wait_vfall"; + case OTG_STATE_A_VBUS_ERR: return "a_vbus_err"; + case OTG_STATE_B_IDLE: return "b_idle"; + case OTG_STATE_B_SRP_INIT: return "b_srp_init"; + case OTG_STATE_B_PERIPHERAL: return "b_peripheral"; + case OTG_STATE_B_WAIT_ACON: return "b_wait_acon"; + case OTG_STATE_B_HOST: return "b_host"; + default: return "UNDEFINED"; + } +} + +#ifdef CONFIG_USB_MUSB_OTG + +/* + * See also USB_OTG_1-3.pdf 6.6.5 Timers + * REVISIT: Are the other timers done in the hardware? + */ +#define TB_ASE0_BRST 100 /* Min 3.125 ms */ + +/* + * Handles OTG hnp timeouts, such as b_ase0_brst + */ +void musb_otg_timer_func(unsigned long data) +{ + struct musb *musb = (struct musb *)data; + unsigned long flags; + + spin_lock_irqsave(&musb->lock, flags); + switch (musb->xceiv.state) { + case OTG_STATE_B_WAIT_ACON: + DBG(1, "HNP: b_wait_acon timeout; back to b_peripheral\n"); + musb_g_disconnect(musb); + musb->xceiv.state = OTG_STATE_B_PERIPHERAL; + musb->is_active = 0; + break; + case OTG_STATE_A_WAIT_BCON: + DBG(1, "HNP: a_wait_bcon timeout; back to a_host\n"); + musb_hnp_stop(musb); + break; + default: + DBG(1, "HNP: Unhandled mode %s\n", otg_state_string(musb)); + } + musb->ignore_disconnect = 0; + spin_unlock_irqrestore(&musb->lock, flags); +} + +static DEFINE_TIMER(musb_otg_timer, musb_otg_timer_func, 0, 0); + +/* + * Stops the B-device HNP state. Caller must take care of locking. + */ +void musb_hnp_stop(struct musb *musb) +{ + struct usb_hcd *hcd = musb_to_hcd(musb); + void __iomem *mbase = musb->mregs; + u8 reg; + + switch (musb->xceiv.state) { + case OTG_STATE_A_PERIPHERAL: + case OTG_STATE_A_WAIT_VFALL: + case OTG_STATE_A_WAIT_BCON: + DBG(1, "HNP: Switching back to A-host\n"); + musb_g_disconnect(musb); + musb->xceiv.state = OTG_STATE_A_IDLE; + MUSB_HST_MODE(musb); + musb->is_active = 0; + break; + case OTG_STATE_B_HOST: + DBG(1, "HNP: Disabling HR\n"); + hcd->self.is_b_host = 0; + musb->xceiv.state = OTG_STATE_B_PERIPHERAL; + MUSB_DEV_MODE(musb); + reg = musb_readb(mbase, MUSB_POWER); + reg |= MUSB_POWER_SUSPENDM; + musb_writeb(mbase, MUSB_POWER, reg); + /* REVISIT: Start SESSION_REQUEST here? */ + break; + default: + DBG(1, "HNP: Stopping in unknown state %s\n", + otg_state_string(musb)); + } + + /* + * When returning to A state after HNP, avoid hub_port_rebounce(), + * which cause occasional OPT A "Did not receive reset after connect" + * errors. + */ + musb->port1_status &= + ~(1 << USB_PORT_FEAT_C_CONNECTION); +} + +#endif + +/* + * Interrupt Service Routine to record USB "global" interrupts. + * Since these do not happen often and signify things of + * paramount importance, it seems OK to check them individually; + * the order of the tests is specified in the manual + * + * @param musb instance pointer + * @param int_usb register contents + * @param devctl + * @param power + */ + +#define STAGE0_MASK (MUSB_INTR_RESUME | MUSB_INTR_SESSREQ \ + | MUSB_INTR_VBUSERROR | MUSB_INTR_CONNECT \ + | MUSB_INTR_RESET) + +static irqreturn_t musb_stage0_irq(struct musb *musb, u8 int_usb, + u8 devctl, u8 power) +{ + irqreturn_t handled = IRQ_NONE; + void __iomem *mbase = musb->mregs; + + DBG(3, "<== Power=%02x, DevCtl=%02x, int_usb=0x%x\n", power, devctl, + int_usb); + + /* in host mode, the peripheral may issue remote wakeup. + * in peripheral mode, the host may resume the link. + * spurious RESUME irqs happen too, paired with SUSPEND. + */ + if (int_usb & MUSB_INTR_RESUME) { + handled = IRQ_HANDLED; + DBG(3, "RESUME (%s)\n", otg_state_string(musb)); + + if (devctl & MUSB_DEVCTL_HM) { +#ifdef CONFIG_USB_MUSB_HDRC_HCD + switch (musb->xceiv.state) { + case OTG_STATE_A_SUSPEND: + /* remote wakeup? later, GetPortStatus + * will stop RESUME signaling + */ + + if (power & MUSB_POWER_SUSPENDM) { + /* spurious */ + musb->int_usb &= ~MUSB_INTR_SUSPEND; + DBG(2, "Spurious SUSPENDM\n"); + break; + } + + power &= ~MUSB_POWER_SUSPENDM; + musb_writeb(mbase, MUSB_POWER, + power | MUSB_POWER_RESUME); + + musb->port1_status |= + (USB_PORT_STAT_C_SUSPEND << 16) + | MUSB_PORT_STAT_RESUME; + musb->rh_timer = jiffies + + msecs_to_jiffies(20); + + musb->xceiv.state = OTG_STATE_A_HOST; + musb->is_active = 1; + usb_hcd_resume_root_hub(musb_to_hcd(musb)); + break; + case OTG_STATE_B_WAIT_ACON: + musb->xceiv.state = OTG_STATE_B_PERIPHERAL; + musb->is_active = 1; + MUSB_DEV_MODE(musb); + break; + default: + WARNING("bogus %s RESUME (%s)\n", + "host", + otg_state_string(musb)); + } +#endif + } else { + switch (musb->xceiv.state) { +#ifdef CONFIG_USB_MUSB_HDRC_HCD + case OTG_STATE_A_SUSPEND: + /* possibly DISCONNECT is upcoming */ + musb->xceiv.state = OTG_STATE_A_HOST; + usb_hcd_resume_root_hub(musb_to_hcd(musb)); + break; +#endif +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + case OTG_STATE_B_WAIT_ACON: + case OTG_STATE_B_PERIPHERAL: + /* disconnect while suspended? we may + * not get a disconnect irq... + */ + if ((devctl & MUSB_DEVCTL_VBUS) + != (3 << MUSB_DEVCTL_VBUS_SHIFT) + ) { + musb->int_usb |= MUSB_INTR_DISCONNECT; + musb->int_usb &= ~MUSB_INTR_SUSPEND; + break; + } + musb_g_resume(musb); + break; + case OTG_STATE_B_IDLE: + musb->int_usb &= ~MUSB_INTR_SUSPEND; + break; +#endif + default: + WARNING("bogus %s RESUME (%s)\n", + "peripheral", + otg_state_string(musb)); + } + } + } + +#ifdef CONFIG_USB_MUSB_HDRC_HCD + /* see manual for the order of the tests */ + if (int_usb & MUSB_INTR_SESSREQ) { + DBG(1, "SESSION_REQUEST (%s)\n", otg_state_string(musb)); + + /* IRQ arrives from ID pin sense or (later, if VBUS power + * is removed) SRP. responses are time critical: + * - turn on VBUS (with silicon-specific mechanism) + * - go through A_WAIT_VRISE + * - ... to A_WAIT_BCON. + * a_wait_vrise_tmout triggers VBUS_ERROR transitions + */ + musb_writeb(mbase, MUSB_DEVCTL, MUSB_DEVCTL_SESSION); + musb->ep0_stage = MUSB_EP0_START; + musb->xceiv.state = OTG_STATE_A_IDLE; + MUSB_HST_MODE(musb); + musb_set_vbus(musb, 1); + + handled = IRQ_HANDLED; + } + + if (int_usb & MUSB_INTR_VBUSERROR) { + int ignore = 0; + + /* During connection as an A-Device, we may see a short + * current spikes causing voltage drop, because of cable + * and peripheral capacitance combined with vbus draw. + * (So: less common with truly self-powered devices, where + * vbus doesn't act like a power supply.) + * + * Such spikes are short; usually less than ~500 usec, max + * of ~2 msec. That is, they're not sustained overcurrent + * errors, though they're reported using VBUSERROR irqs. + * + * Workarounds: (a) hardware: use self powered devices. + * (b) software: ignore non-repeated VBUS errors. + * + * REVISIT: do delays from lots of DEBUG_KERNEL checks + * make trouble here, keeping VBUS < 4.4V ? + */ + switch (musb->xceiv.state) { + case OTG_STATE_A_HOST: + /* recovery is dicey once we've gotten past the + * initial stages of enumeration, but if VBUS + * stayed ok at the other end of the link, and + * another reset is due (at least for high speed, + * to redo the chirp etc), it might work OK... + */ + case OTG_STATE_A_WAIT_BCON: + case OTG_STATE_A_WAIT_VRISE: + if (musb->vbuserr_retry) { + musb->vbuserr_retry--; + ignore = 1; + devctl |= MUSB_DEVCTL_SESSION; + musb_writeb(mbase, MUSB_DEVCTL, devctl); + } else { + musb->port1_status |= + (1 << USB_PORT_FEAT_OVER_CURRENT) + | (1 << USB_PORT_FEAT_C_OVER_CURRENT); + } + break; + default: + break; + } + + DBG(1, "VBUS_ERROR in %s (%02x, %s), retry #%d, port1 %08x\n", + otg_state_string(musb), + devctl, + ({ char *s; + switch (devctl & MUSB_DEVCTL_VBUS) { + case 0 << MUSB_DEVCTL_VBUS_SHIFT: + s = "vbuserr_retry, + musb->port1_status); + + /* go through A_WAIT_VFALL then start a new session */ + if (!ignore) + musb_set_vbus(musb, 0); + handled = IRQ_HANDLED; + } + + if (int_usb & MUSB_INTR_CONNECT) { + struct usb_hcd *hcd = musb_to_hcd(musb); + + handled = IRQ_HANDLED; + musb->is_active = 1; + set_bit(HCD_FLAG_SAW_IRQ, &hcd->flags); + + musb->ep0_stage = MUSB_EP0_START; + +#ifdef CONFIG_USB_MUSB_OTG + /* flush endpoints when transitioning from Device Mode */ + if (is_peripheral_active(musb)) { + /* REVISIT HNP; just force disconnect */ + } + musb_writew(mbase, MUSB_INTRTXE, musb->epmask); + musb_writew(mbase, MUSB_INTRRXE, musb->epmask & 0xfffe); + musb_writeb(mbase, MUSB_INTRUSBE, 0xf7); +#endif + musb->port1_status &= ~(USB_PORT_STAT_LOW_SPEED + |USB_PORT_STAT_HIGH_SPEED + |USB_PORT_STAT_ENABLE + ); + musb->port1_status |= USB_PORT_STAT_CONNECTION + |(USB_PORT_STAT_C_CONNECTION << 16); + + /* high vs full speed is just a guess until after reset */ + if (devctl & MUSB_DEVCTL_LSDEV) + musb->port1_status |= USB_PORT_STAT_LOW_SPEED; + + if (hcd->status_urb) + usb_hcd_poll_rh_status(hcd); + else + usb_hcd_resume_root_hub(hcd); + + MUSB_HST_MODE(musb); + + /* indicate new connection to OTG machine */ + switch (musb->xceiv.state) { + case OTG_STATE_B_PERIPHERAL: + if (int_usb & MUSB_INTR_SUSPEND) { + DBG(1, "HNP: SUSPEND+CONNECT, now b_host\n"); + musb->xceiv.state = OTG_STATE_B_HOST; + hcd->self.is_b_host = 1; + int_usb &= ~MUSB_INTR_SUSPEND; + } else + DBG(1, "CONNECT as b_peripheral???\n"); + break; + case OTG_STATE_B_WAIT_ACON: + DBG(1, "HNP: Waiting to switch to b_host state\n"); + musb->xceiv.state = OTG_STATE_B_HOST; + hcd->self.is_b_host = 1; + break; + default: + if ((devctl & MUSB_DEVCTL_VBUS) + == (3 << MUSB_DEVCTL_VBUS_SHIFT)) { + musb->xceiv.state = OTG_STATE_A_HOST; + hcd->self.is_b_host = 0; + } + break; + } + DBG(1, "CONNECT (%s) devctl %02x\n", + otg_state_string(musb), devctl); + } +#endif /* CONFIG_USB_MUSB_HDRC_HCD */ + + /* mentor saves a bit: bus reset and babble share the same irq. + * only host sees babble; only peripheral sees bus reset. + */ + if (int_usb & MUSB_INTR_RESET) { + if (is_host_capable() && (devctl & MUSB_DEVCTL_HM) != 0) { + /* + * Looks like non-HS BABBLE can be ignored, but + * HS BABBLE is an error condition. For HS the solution + * is to avoid babble in the first place and fix what + * caused BABBLE. When HS BABBLE happens we can only + * stop the session. + */ + if (devctl & (MUSB_DEVCTL_FSDEV | MUSB_DEVCTL_LSDEV)) + DBG(1, "BABBLE devctl: %02x\n", devctl); + else { + ERR("Stopping host session -- babble\n"); + musb_writeb(mbase, MUSB_DEVCTL, 0); + } + } else if (is_peripheral_capable()) { + DBG(1, "BUS RESET as %s\n", otg_state_string(musb)); + switch (musb->xceiv.state) { +#ifdef CONFIG_USB_OTG + case OTG_STATE_A_SUSPEND: + /* We need to ignore disconnect on suspend + * otherwise tusb 2.0 won't reconnect after a + * power cycle, which breaks otg compliance. + */ + musb->ignore_disconnect = 1; + musb_g_reset(musb); + /* FALLTHROUGH */ + case OTG_STATE_A_WAIT_BCON: /* OPT TD.4.7-900ms */ + DBG(1, "HNP: Setting timer as %s\n", + otg_state_string(musb)); + musb_otg_timer.data = (unsigned long)musb; + mod_timer(&musb_otg_timer, jiffies + + msecs_to_jiffies(100)); + break; + case OTG_STATE_A_PERIPHERAL: + musb_hnp_stop(musb); + break; + case OTG_STATE_B_WAIT_ACON: + DBG(1, "HNP: RESET (%s), to b_peripheral\n", + otg_state_string(musb)); + musb->xceiv.state = OTG_STATE_B_PERIPHERAL; + musb_g_reset(musb); + break; +#endif + case OTG_STATE_B_IDLE: + musb->xceiv.state = OTG_STATE_B_PERIPHERAL; + /* FALLTHROUGH */ + case OTG_STATE_B_PERIPHERAL: + musb_g_reset(musb); + break; + default: + DBG(1, "Unhandled BUS RESET as %s\n", + otg_state_string(musb)); + } + } + + handled = IRQ_HANDLED; + } + schedule_work(&musb->irq_work); + + return handled; +} + +/* + * Interrupt Service Routine to record USB "global" interrupts. + * Since these do not happen often and signify things of + * paramount importance, it seems OK to check them individually; + * the order of the tests is specified in the manual + * + * @param musb instance pointer + * @param int_usb register contents + * @param devctl + * @param power + */ +static irqreturn_t musb_stage2_irq(struct musb *musb, u8 int_usb, + u8 devctl, u8 power) +{ + irqreturn_t handled = IRQ_NONE; + +#if 0 +/* REVISIT ... this would be for multiplexing periodic endpoints, or + * supporting transfer phasing to prevent exceeding ISO bandwidth + * limits of a given frame or microframe. + * + * It's not needed for peripheral side, which dedicates endpoints; + * though it _might_ use SOF irqs for other purposes. + * + * And it's not currently needed for host side, which also dedicates + * endpoints, relies on TX/RX interval registers, and isn't claimed + * to support ISO transfers yet. + */ + if (int_usb & MUSB_INTR_SOF) { + void __iomem *mbase = musb->mregs; + struct musb_hw_ep *ep; + u8 epnum; + u16 frame; + + DBG(6, "START_OF_FRAME\n"); + handled = IRQ_HANDLED; + + /* start any periodic Tx transfers waiting for current frame */ + frame = musb_readw(mbase, MUSB_FRAME); + ep = musb->endpoints; + for (epnum = 1; (epnum < musb->nr_endpoints) + && (musb->epmask >= (1 << epnum)); + epnum++, ep++) { + /* + * FIXME handle framecounter wraps (12 bits) + * eliminate duplicated StartUrb logic + */ + if (ep->dwWaitFrame >= frame) { + ep->dwWaitFrame = 0; + pr_debug("SOF --> periodic TX%s on %d\n", + ep->tx_channel ? " DMA" : "", + epnum); + if (!ep->tx_channel) + musb_h_tx_start(musb, epnum); + else + cppi_hostdma_start(musb, epnum); + } + } /* end of for loop */ + } +#endif + + if ((int_usb & MUSB_INTR_DISCONNECT) && !musb->ignore_disconnect) { + DBG(1, "DISCONNECT (%s) as %s, devctl %02x\n", + otg_state_string(musb), + MUSB_MODE(musb), devctl); + handled = IRQ_HANDLED; + + switch (musb->xceiv.state) { +#ifdef CONFIG_USB_MUSB_HDRC_HCD + case OTG_STATE_A_HOST: + case OTG_STATE_A_SUSPEND: + musb_root_disconnect(musb); + if (musb->a_wait_bcon != 0) + musb_platform_try_idle(musb, jiffies + + msecs_to_jiffies(musb->a_wait_bcon)); + break; +#endif /* HOST */ +#ifdef CONFIG_USB_MUSB_OTG + case OTG_STATE_B_HOST: + musb_hnp_stop(musb); + break; + case OTG_STATE_A_PERIPHERAL: + musb_hnp_stop(musb); + musb_root_disconnect(musb); + /* FALLTHROUGH */ + case OTG_STATE_B_WAIT_ACON: + /* FALLTHROUGH */ +#endif /* OTG */ +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + case OTG_STATE_B_PERIPHERAL: + case OTG_STATE_B_IDLE: + musb_g_disconnect(musb); + break; +#endif /* GADGET */ + default: + WARNING("unhandled DISCONNECT transition (%s)\n", + otg_state_string(musb)); + break; + } + + schedule_work(&musb->irq_work); + } + + if (int_usb & MUSB_INTR_SUSPEND) { + DBG(1, "SUSPEND (%s) devctl %02x power %02x\n", + otg_state_string(musb), devctl, power); + handled = IRQ_HANDLED; + + switch (musb->xceiv.state) { +#ifdef CONFIG_USB_MUSB_OTG + case OTG_STATE_A_PERIPHERAL: + /* + * We cannot stop HNP here, devctl BDEVICE might be + * still set. + */ + break; +#endif + case OTG_STATE_B_PERIPHERAL: + musb_g_suspend(musb); + musb->is_active = is_otg_enabled(musb) + && musb->xceiv.gadget->b_hnp_enable; + if (musb->is_active) { +#ifdef CONFIG_USB_MUSB_OTG + musb->xceiv.state = OTG_STATE_B_WAIT_ACON; + DBG(1, "HNP: Setting timer for b_ase0_brst\n"); + musb_otg_timer.data = (unsigned long)musb; + mod_timer(&musb_otg_timer, jiffies + + msecs_to_jiffies(TB_ASE0_BRST)); +#endif + } + break; + case OTG_STATE_A_WAIT_BCON: + if (musb->a_wait_bcon != 0) + musb_platform_try_idle(musb, jiffies + + msecs_to_jiffies(musb->a_wait_bcon)); + break; + case OTG_STATE_A_HOST: + musb->xceiv.state = OTG_STATE_A_SUSPEND; + musb->is_active = is_otg_enabled(musb) + && musb->xceiv.host->b_hnp_enable; + break; + case OTG_STATE_B_HOST: + /* Transition to B_PERIPHERAL, see 6.8.2.6 p 44 */ + DBG(1, "REVISIT: SUSPEND as B_HOST\n"); + break; + default: + /* "should not happen" */ + musb->is_active = 0; + break; + } + schedule_work(&musb->irq_work); + } + + + return handled; +} + +/*-------------------------------------------------------------------------*/ + +/* +* Program the HDRC to start (enable interrupts, dma, etc.). +*/ +void musb_start(struct musb *musb) +{ + void __iomem *regs = musb->mregs; + u8 devctl = musb_readb(regs, MUSB_DEVCTL); + + DBG(2, "<== devctl %02x\n", devctl); + + /* Set INT enable registers, enable interrupts */ + musb_writew(regs, MUSB_INTRTXE, musb->epmask); + musb_writew(regs, MUSB_INTRRXE, musb->epmask & 0xfffe); + musb_writeb(regs, MUSB_INTRUSBE, 0xf7); + + musb_writeb(regs, MUSB_TESTMODE, 0); + + /* put into basic highspeed mode and start session */ + musb_writeb(regs, MUSB_POWER, MUSB_POWER_ISOUPDATE + | MUSB_POWER_SOFTCONN + | MUSB_POWER_HSENAB + /* ENSUSPEND wedges tusb */ + /* | MUSB_POWER_ENSUSPEND */ + ); + + musb->is_active = 0; + devctl = musb_readb(regs, MUSB_DEVCTL); + devctl &= ~MUSB_DEVCTL_SESSION; + + if (is_otg_enabled(musb)) { + /* session started after: + * (a) ID-grounded irq, host mode; + * (b) vbus present/connect IRQ, peripheral mode; + * (c) peripheral initiates, using SRP + */ + if ((devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS) + musb->is_active = 1; + else + devctl |= MUSB_DEVCTL_SESSION; + + } else if (is_host_enabled(musb)) { + /* assume ID pin is hard-wired to ground */ + devctl |= MUSB_DEVCTL_SESSION; + + } else /* peripheral is enabled */ { + if ((devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS) + musb->is_active = 1; + } + musb_platform_enable(musb); + musb_writeb(regs, MUSB_DEVCTL, devctl); +} + + +static void musb_generic_disable(struct musb *musb) +{ + void __iomem *mbase = musb->mregs; + u16 temp; + + /* disable interrupts */ + musb_writeb(mbase, MUSB_INTRUSBE, 0); + musb_writew(mbase, MUSB_INTRTXE, 0); + musb_writew(mbase, MUSB_INTRRXE, 0); + + /* off */ + musb_writeb(mbase, MUSB_DEVCTL, 0); + + /* flush pending interrupts */ + temp = musb_readb(mbase, MUSB_INTRUSB); + temp = musb_readw(mbase, MUSB_INTRTX); + temp = musb_readw(mbase, MUSB_INTRRX); + +} + +/* + * Make the HDRC stop (disable interrupts, etc.); + * reversible by musb_start + * called on gadget driver unregister + * with controller locked, irqs blocked + * acts as a NOP unless some role activated the hardware + */ +void musb_stop(struct musb *musb) +{ + /* stop IRQs, timers, ... */ + musb_platform_disable(musb); + musb_generic_disable(musb); + DBG(3, "HDRC disabled\n"); + + /* FIXME + * - mark host and/or peripheral drivers unusable/inactive + * - disable DMA (and enable it in HdrcStart) + * - make sure we can musb_start() after musb_stop(); with + * OTG mode, gadget driver module rmmod/modprobe cycles that + * - ... + */ + musb_platform_try_idle(musb, 0); +} + +static void musb_shutdown(struct platform_device *pdev) +{ + struct musb *musb = dev_to_musb(&pdev->dev); + unsigned long flags; + + spin_lock_irqsave(&musb->lock, flags); + musb_platform_disable(musb); + musb_generic_disable(musb); + if (musb->clock) { + clk_put(musb->clock); + musb->clock = NULL; + } + spin_unlock_irqrestore(&musb->lock, flags); + + /* FIXME power down */ +} + + +/*-------------------------------------------------------------------------*/ + +/* + * The silicon either has hard-wired endpoint configurations, or else + * "dynamic fifo" sizing. The driver has support for both, though at this + * writing only the dynamic sizing is very well tested. We use normal + * idioms to so both modes are compile-tested, but dead code elimination + * leaves only the relevant one in the object file. + * + * We don't currently use dynamic fifo setup capability to do anything + * more than selecting one of a bunch of predefined configurations. + */ +#ifdef MUSB_C_DYNFIFO_DEF +#define can_dynfifo() 1 +#else +#define can_dynfifo() 0 +#endif + +#if defined(CONFIG_USB_TUSB6010) || \ + defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP34XX) +static ushort __initdata fifo_mode = 4; +#else +static ushort __initdata fifo_mode = 2; +#endif + +/* "modprobe ... fifo_mode=1" etc */ +module_param(fifo_mode, ushort, 0); +MODULE_PARM_DESC(fifo_mode, "initial endpoint configuration"); + + +#define DYN_FIFO_SIZE (1<<(MUSB_C_RAM_BITS+2)) + +enum fifo_style { FIFO_RXTX, FIFO_TX, FIFO_RX } __attribute__ ((packed)); +enum buf_mode { BUF_SINGLE, BUF_DOUBLE } __attribute__ ((packed)); + +struct fifo_cfg { + u8 hw_ep_num; + enum fifo_style style; + enum buf_mode mode; + u16 maxpacket; +}; + +/* + * tables defining fifo_mode values. define more if you like. + * for host side, make sure both halves of ep1 are set up. + */ + +/* mode 0 - fits in 2KB */ +static struct fifo_cfg __initdata mode_0_cfg[] = { +{ .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, }, +{ .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, }, +{ .hw_ep_num = 2, .style = FIFO_RXTX, .maxpacket = 512, }, +{ .hw_ep_num = 3, .style = FIFO_RXTX, .maxpacket = 256, }, +{ .hw_ep_num = 4, .style = FIFO_RXTX, .maxpacket = 256, }, +}; + +/* mode 1 - fits in 4KB */ +static struct fifo_cfg __initdata mode_1_cfg[] = { +{ .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, .mode = BUF_DOUBLE, }, +{ .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, .mode = BUF_DOUBLE, }, +{ .hw_ep_num = 2, .style = FIFO_RXTX, .maxpacket = 512, .mode = BUF_DOUBLE, }, +{ .hw_ep_num = 3, .style = FIFO_RXTX, .maxpacket = 256, }, +{ .hw_ep_num = 4, .style = FIFO_RXTX, .maxpacket = 256, }, +}; + +/* mode 2 - fits in 4KB */ +static struct fifo_cfg __initdata mode_2_cfg[] = { +{ .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, }, +{ .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, }, +{ .hw_ep_num = 2, .style = FIFO_TX, .maxpacket = 512, }, +{ .hw_ep_num = 2, .style = FIFO_RX, .maxpacket = 512, }, +{ .hw_ep_num = 3, .style = FIFO_RXTX, .maxpacket = 256, }, +{ .hw_ep_num = 4, .style = FIFO_RXTX, .maxpacket = 256, }, +}; + +/* mode 3 - fits in 4KB */ +static struct fifo_cfg __initdata mode_3_cfg[] = { +{ .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, .mode = BUF_DOUBLE, }, +{ .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, .mode = BUF_DOUBLE, }, +{ .hw_ep_num = 2, .style = FIFO_TX, .maxpacket = 512, }, +{ .hw_ep_num = 2, .style = FIFO_RX, .maxpacket = 512, }, +{ .hw_ep_num = 3, .style = FIFO_RXTX, .maxpacket = 256, }, +{ .hw_ep_num = 4, .style = FIFO_RXTX, .maxpacket = 256, }, +}; + +/* mode 4 - fits in 16KB */ +static struct fifo_cfg __initdata mode_4_cfg[] = { +{ .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, }, +{ .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, }, +{ .hw_ep_num = 2, .style = FIFO_TX, .maxpacket = 512, }, +{ .hw_ep_num = 2, .style = FIFO_RX, .maxpacket = 512, }, +{ .hw_ep_num = 3, .style = FIFO_TX, .maxpacket = 512, }, +{ .hw_ep_num = 3, .style = FIFO_RX, .maxpacket = 512, }, +{ .hw_ep_num = 4, .style = FIFO_TX, .maxpacket = 512, }, +{ .hw_ep_num = 4, .style = FIFO_RX, .maxpacket = 512, }, +{ .hw_ep_num = 5, .style = FIFO_TX, .maxpacket = 512, }, +{ .hw_ep_num = 5, .style = FIFO_RX, .maxpacket = 512, }, +{ .hw_ep_num = 6, .style = FIFO_TX, .maxpacket = 512, }, +{ .hw_ep_num = 6, .style = FIFO_RX, .maxpacket = 512, }, +{ .hw_ep_num = 7, .style = FIFO_TX, .maxpacket = 512, }, +{ .hw_ep_num = 7, .style = FIFO_RX, .maxpacket = 512, }, +{ .hw_ep_num = 8, .style = FIFO_TX, .maxpacket = 512, }, +{ .hw_ep_num = 8, .style = FIFO_RX, .maxpacket = 512, }, +{ .hw_ep_num = 9, .style = FIFO_TX, .maxpacket = 512, }, +{ .hw_ep_num = 9, .style = FIFO_RX, .maxpacket = 512, }, +{ .hw_ep_num = 10, .style = FIFO_TX, .maxpacket = 512, }, +{ .hw_ep_num = 10, .style = FIFO_RX, .maxpacket = 512, }, +{ .hw_ep_num = 11, .style = FIFO_TX, .maxpacket = 512, }, +{ .hw_ep_num = 11, .style = FIFO_RX, .maxpacket = 512, }, +{ .hw_ep_num = 12, .style = FIFO_TX, .maxpacket = 512, }, +{ .hw_ep_num = 12, .style = FIFO_RX, .maxpacket = 512, }, +{ .hw_ep_num = 13, .style = FIFO_TX, .maxpacket = 512, }, +{ .hw_ep_num = 13, .style = FIFO_RX, .maxpacket = 512, }, +{ .hw_ep_num = 14, .style = FIFO_RXTX, .maxpacket = 1024, }, +{ .hw_ep_num = 15, .style = FIFO_RXTX, .maxpacket = 1024, }, +}; + + +/* + * configure a fifo; for non-shared endpoints, this may be called + * once for a tx fifo and once for an rx fifo. + * + * returns negative errno or offset for next fifo. + */ +static int __init +fifo_setup(struct musb *musb, struct musb_hw_ep *hw_ep, + const struct fifo_cfg *cfg, u16 offset) +{ + void __iomem *mbase = musb->mregs; + int size = 0; + u16 maxpacket = cfg->maxpacket; + u16 c_off = offset >> 3; + u8 c_size; + + /* expect hw_ep has already been zero-initialized */ + + size = ffs(max(maxpacket, (u16) 8)) - 1; + maxpacket = 1 << size; + + c_size = size - 3; + if (cfg->mode == BUF_DOUBLE) { + if ((offset + (maxpacket << 1)) > DYN_FIFO_SIZE) + return -EMSGSIZE; + c_size |= MUSB_FIFOSZ_DPB; + } else { + if ((offset + maxpacket) > DYN_FIFO_SIZE) + return -EMSGSIZE; + } + + /* configure the FIFO */ + musb_writeb(mbase, MUSB_INDEX, hw_ep->epnum); + +#ifdef CONFIG_USB_MUSB_HDRC_HCD + /* EP0 reserved endpoint for control, bidirectional; + * EP1 reserved for bulk, two unidirection halves. + */ + if (hw_ep->epnum == 1) + musb->bulk_ep = hw_ep; + /* REVISIT error check: be sure ep0 can both rx and tx ... */ +#endif + switch (cfg->style) { + case FIFO_TX: + musb_writeb(mbase, MUSB_TXFIFOSZ, c_size); + musb_writew(mbase, MUSB_TXFIFOADD, c_off); + hw_ep->tx_double_buffered = !!(c_size & MUSB_FIFOSZ_DPB); + hw_ep->max_packet_sz_tx = maxpacket; + break; + case FIFO_RX: + musb_writeb(mbase, MUSB_RXFIFOSZ, c_size); + musb_writew(mbase, MUSB_RXFIFOADD, c_off); + hw_ep->rx_double_buffered = !!(c_size & MUSB_FIFOSZ_DPB); + hw_ep->max_packet_sz_rx = maxpacket; + break; + case FIFO_RXTX: + musb_writeb(mbase, MUSB_TXFIFOSZ, c_size); + musb_writew(mbase, MUSB_TXFIFOADD, c_off); + hw_ep->rx_double_buffered = !!(c_size & MUSB_FIFOSZ_DPB); + hw_ep->max_packet_sz_rx = maxpacket; + + musb_writeb(mbase, MUSB_RXFIFOSZ, c_size); + musb_writew(mbase, MUSB_RXFIFOADD, c_off); + hw_ep->tx_double_buffered = hw_ep->rx_double_buffered; + hw_ep->max_packet_sz_tx = maxpacket; + + hw_ep->is_shared_fifo = true; + break; + } + + /* NOTE rx and tx endpoint irqs aren't managed separately, + * which happens to be ok + */ + musb->epmask |= (1 << hw_ep->epnum); + + return offset + (maxpacket << ((c_size & MUSB_FIFOSZ_DPB) ? 1 : 0)); +} + +static struct fifo_cfg __initdata ep0_cfg = { + .style = FIFO_RXTX, .maxpacket = 64, +}; + +static int __init ep_config_from_table(struct musb *musb) +{ + const struct fifo_cfg *cfg; + unsigned i, n; + int offset; + struct musb_hw_ep *hw_ep = musb->endpoints; + + switch (fifo_mode) { + default: + fifo_mode = 0; + /* FALLTHROUGH */ + case 0: + cfg = mode_0_cfg; + n = ARRAY_SIZE(mode_0_cfg); + break; + case 1: + cfg = mode_1_cfg; + n = ARRAY_SIZE(mode_1_cfg); + break; + case 2: + cfg = mode_2_cfg; + n = ARRAY_SIZE(mode_2_cfg); + break; + case 3: + cfg = mode_3_cfg; + n = ARRAY_SIZE(mode_3_cfg); + break; + case 4: + cfg = mode_4_cfg; + n = ARRAY_SIZE(mode_4_cfg); + break; + } + + printk(KERN_DEBUG "%s: setup fifo_mode %d\n", + musb_driver_name, fifo_mode); + + + offset = fifo_setup(musb, hw_ep, &ep0_cfg, 0); + /* assert(offset > 0) */ + + /* NOTE: for RTL versions >= 1.400 EPINFO and RAMINFO would + * be better than static MUSB_C_NUM_EPS and DYN_FIFO_SIZE... + */ + + for (i = 0; i < n; i++) { + u8 epn = cfg->hw_ep_num; + + if (epn >= MUSB_C_NUM_EPS) { + pr_debug("%s: invalid ep %d\n", + musb_driver_name, epn); + continue; + } + offset = fifo_setup(musb, hw_ep + epn, cfg++, offset); + if (offset < 0) { + pr_debug("%s: mem overrun, ep %d\n", + musb_driver_name, epn); + return -EINVAL; + } + epn++; + musb->nr_endpoints = max(epn, musb->nr_endpoints); + } + + printk(KERN_DEBUG "%s: %d/%d max ep, %d/%d memory\n", + musb_driver_name, + n + 1, MUSB_C_NUM_EPS * 2 - 1, + offset, DYN_FIFO_SIZE); + +#ifdef CONFIG_USB_MUSB_HDRC_HCD + if (!musb->bulk_ep) { + pr_debug("%s: missing bulk\n", musb_driver_name); + return -EINVAL; + } +#endif + + return 0; +} + + +/* + * ep_config_from_hw - when MUSB_C_DYNFIFO_DEF is false + * @param musb the controller + */ +static int __init ep_config_from_hw(struct musb *musb) +{ + u8 epnum = 0, reg; + struct musb_hw_ep *hw_ep; + void *mbase = musb->mregs; + + DBG(2, "<== static silicon ep config\n"); + + /* FIXME pick up ep0 maxpacket size */ + + for (epnum = 1; epnum < MUSB_C_NUM_EPS; epnum++) { + musb_ep_select(mbase, epnum); + hw_ep = musb->endpoints + epnum; + + /* read from core using indexed model */ + reg = musb_readb(hw_ep->regs, 0x10 + MUSB_FIFOSIZE); + if (!reg) { + /* 0's returned when no more endpoints */ + break; + } + musb->nr_endpoints++; + musb->epmask |= (1 << epnum); + + hw_ep->max_packet_sz_tx = 1 << (reg & 0x0f); + + /* shared TX/RX FIFO? */ + if ((reg & 0xf0) == 0xf0) { + hw_ep->max_packet_sz_rx = hw_ep->max_packet_sz_tx; + hw_ep->is_shared_fifo = true; + continue; + } else { + hw_ep->max_packet_sz_rx = 1 << ((reg & 0xf0) >> 4); + hw_ep->is_shared_fifo = false; + } + + /* FIXME set up hw_ep->{rx,tx}_double_buffered */ + +#ifdef CONFIG_USB_MUSB_HDRC_HCD + /* pick an RX/TX endpoint for bulk */ + if (hw_ep->max_packet_sz_tx < 512 + || hw_ep->max_packet_sz_rx < 512) + continue; + + /* REVISIT: this algorithm is lazy, we should at least + * try to pick a double buffered endpoint. + */ + if (musb->bulk_ep) + continue; + musb->bulk_ep = hw_ep; +#endif + } + +#ifdef CONFIG_USB_MUSB_HDRC_HCD + if (!musb->bulk_ep) { + pr_debug("%s: missing bulk\n", musb_driver_name); + return -EINVAL; + } +#endif + + return 0; +} + +enum { MUSB_CONTROLLER_MHDRC, MUSB_CONTROLLER_HDRC, }; + +/* Initialize MUSB (M)HDRC part of the USB hardware subsystem; + * configure endpoints, or take their config from silicon + */ +static int __init musb_core_init(u16 musb_type, struct musb *musb) +{ +#ifdef MUSB_AHB_ID + u32 data; +#endif + u8 reg; + char *type; + u16 hwvers, rev_major, rev_minor; + char aInfo[78], aRevision[32], aDate[12]; + void __iomem *mbase = musb->mregs; + int status = 0; + int i; + + /* log core options (read using indexed model) */ + musb_ep_select(mbase, 0); + reg = musb_readb(mbase, 0x10 + MUSB_CONFIGDATA); + + strcpy(aInfo, (reg & MUSB_CONFIGDATA_UTMIDW) ? "UTMI-16" : "UTMI-8"); + if (reg & MUSB_CONFIGDATA_DYNFIFO) + strcat(aInfo, ", dyn FIFOs"); + if (reg & MUSB_CONFIGDATA_MPRXE) { + strcat(aInfo, ", bulk combine"); +#ifdef C_MP_RX + musb->bulk_combine = true; +#else + strcat(aInfo, " (X)"); /* no driver support */ +#endif + } + if (reg & MUSB_CONFIGDATA_MPTXE) { + strcat(aInfo, ", bulk split"); +#ifdef C_MP_TX + musb->bulk_split = true; +#else + strcat(aInfo, " (X)"); /* no driver support */ +#endif + } + if (reg & MUSB_CONFIGDATA_HBRXE) { + strcat(aInfo, ", HB-ISO Rx"); + strcat(aInfo, " (X)"); /* no driver support */ + } + if (reg & MUSB_CONFIGDATA_HBTXE) { + strcat(aInfo, ", HB-ISO Tx"); + strcat(aInfo, " (X)"); /* no driver support */ + } + if (reg & MUSB_CONFIGDATA_SOFTCONE) + strcat(aInfo, ", SoftConn"); + + printk(KERN_DEBUG "%s: ConfigData=0x%02x (%s)\n", + musb_driver_name, reg, aInfo); + +#ifdef MUSB_AHB_ID + data = musb_readl(mbase, 0x404); + sprintf(aDate, "%04d-%02x-%02x", (data & 0xffff), + (data >> 16) & 0xff, (data >> 24) & 0xff); + /* FIXME ID2 and ID3 are unused */ + data = musb_readl(mbase, 0x408); + printk(KERN_DEBUG "ID2=%lx\n", (long unsigned)data); + data = musb_readl(mbase, 0x40c); + printk(KERN_DEBUG "ID3=%lx\n", (long unsigned)data); + reg = musb_readb(mbase, 0x400); + musb_type = ('M' == reg) ? MUSB_CONTROLLER_MHDRC : MUSB_CONTROLLER_HDRC; +#else + aDate[0] = 0; +#endif + if (MUSB_CONTROLLER_MHDRC == musb_type) { + musb->is_multipoint = 1; + type = "M"; + } else { + musb->is_multipoint = 0; + type = ""; +#ifdef CONFIG_USB_MUSB_HDRC_HCD +#ifndef CONFIG_USB_OTG_BLACKLIST_HUB + printk(KERN_ERR + "%s: kernel must blacklist external hubs\n", + musb_driver_name); +#endif +#endif + } + + /* log release info */ + hwvers = musb_readw(mbase, MUSB_HWVERS); + rev_major = (hwvers >> 10) & 0x1f; + rev_minor = hwvers & 0x3ff; + snprintf(aRevision, 32, "%d.%d%s", rev_major, + rev_minor, (hwvers & 0x8000) ? "RC" : ""); + printk(KERN_DEBUG "%s: %sHDRC RTL version %s %s\n", + musb_driver_name, type, aRevision, aDate); + + /* configure ep0 */ + musb->endpoints[0].max_packet_sz_tx = MUSB_EP0_FIFOSIZE; + musb->endpoints[0].max_packet_sz_rx = MUSB_EP0_FIFOSIZE; + + /* discover endpoint configuration */ + musb->nr_endpoints = 1; + musb->epmask = 1; + + if (reg & MUSB_CONFIGDATA_DYNFIFO) { + if (can_dynfifo()) + status = ep_config_from_table(musb); + else { + ERR("reconfigure software for Dynamic FIFOs\n"); + status = -ENODEV; + } + } else { + if (!can_dynfifo()) + status = ep_config_from_hw(musb); + else { + ERR("reconfigure software for static FIFOs\n"); + return -ENODEV; + } + } + + if (status < 0) + return status; + + /* finish init, and print endpoint config */ + for (i = 0; i < musb->nr_endpoints; i++) { + struct musb_hw_ep *hw_ep = musb->endpoints + i; + + hw_ep->fifo = MUSB_FIFO_OFFSET(i) + mbase; +#ifdef CONFIG_USB_TUSB6010 + hw_ep->fifo_async = musb->async + 0x400 + MUSB_FIFO_OFFSET(i); + hw_ep->fifo_sync = musb->sync + 0x400 + MUSB_FIFO_OFFSET(i); + hw_ep->fifo_sync_va = + musb->sync_va + 0x400 + MUSB_FIFO_OFFSET(i); + + if (i == 0) + hw_ep->conf = mbase - 0x400 + TUSB_EP0_CONF; + else + hw_ep->conf = mbase + 0x400 + (((i - 1) & 0xf) << 2); +#endif + + hw_ep->regs = MUSB_EP_OFFSET(i, 0) + mbase; +#ifdef CONFIG_USB_MUSB_HDRC_HCD + hw_ep->target_regs = MUSB_BUSCTL_OFFSET(i, 0) + mbase; + hw_ep->rx_reinit = 1; + hw_ep->tx_reinit = 1; +#endif + + if (hw_ep->max_packet_sz_tx) { + printk(KERN_DEBUG + "%s: hw_ep %d%s, %smax %d\n", + musb_driver_name, i, + hw_ep->is_shared_fifo ? "shared" : "tx", + hw_ep->tx_double_buffered + ? "doublebuffer, " : "", + hw_ep->max_packet_sz_tx); + } + if (hw_ep->max_packet_sz_rx && !hw_ep->is_shared_fifo) { + printk(KERN_DEBUG + "%s: hw_ep %d%s, %smax %d\n", + musb_driver_name, i, + "rx", + hw_ep->rx_double_buffered + ? "doublebuffer, " : "", + hw_ep->max_packet_sz_rx); + } + if (!(hw_ep->max_packet_sz_tx || hw_ep->max_packet_sz_rx)) + DBG(1, "hw_ep %d not configured\n", i); + } + + return 0; +} + +/*-------------------------------------------------------------------------*/ + +#if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3430) + +static irqreturn_t generic_interrupt(int irq, void *__hci) +{ + unsigned long flags; + irqreturn_t retval = IRQ_NONE; + struct musb *musb = __hci; + + spin_lock_irqsave(&musb->lock, flags); + + musb->int_usb = musb_readb(musb->mregs, MUSB_INTRUSB); + musb->int_tx = musb_readw(musb->mregs, MUSB_INTRTX); + musb->int_rx = musb_readw(musb->mregs, MUSB_INTRRX); + + if (musb->int_usb || musb->int_tx || musb->int_rx) + retval = musb_interrupt(musb); + + spin_unlock_irqrestore(&musb->lock, flags); + + /* REVISIT we sometimes get spurious IRQs on g_ep0 + * not clear why... + */ + if (retval != IRQ_HANDLED) + DBG(5, "spurious?\n"); + + return IRQ_HANDLED; +} + +#else +#define generic_interrupt NULL +#endif + +/* + * handle all the irqs defined by the HDRC core. for now we expect: other + * irq sources (phy, dma, etc) will be handled first, musb->int_* values + * will be assigned, and the irq will already have been acked. + * + * called in irq context with spinlock held, irqs blocked + */ +irqreturn_t musb_interrupt(struct musb *musb) +{ + irqreturn_t retval = IRQ_NONE; + u8 devctl, power; + int ep_num; + u32 reg; + + devctl = musb_readb(musb->mregs, MUSB_DEVCTL); + power = musb_readb(musb->mregs, MUSB_POWER); + + DBG(4, "** IRQ %s usb%04x tx%04x rx%04x\n", + (devctl & MUSB_DEVCTL_HM) ? "host" : "peripheral", + musb->int_usb, musb->int_tx, musb->int_rx); + + /* the core can interrupt us for multiple reasons; docs have + * a generic interrupt flowchart to follow + */ + if (musb->int_usb & STAGE0_MASK) + retval |= musb_stage0_irq(musb, musb->int_usb, + devctl, power); + + /* "stage 1" is handling endpoint irqs */ + + /* handle endpoint 0 first */ + if (musb->int_tx & 1) { + if (devctl & MUSB_DEVCTL_HM) + retval |= musb_h_ep0_irq(musb); + else + retval |= musb_g_ep0_irq(musb); + } + + /* RX on endpoints 1-15 */ + reg = musb->int_rx >> 1; + ep_num = 1; + while (reg) { + if (reg & 1) { + /* musb_ep_select(musb->mregs, ep_num); */ + /* REVISIT just retval = ep->rx_irq(...) */ + retval = IRQ_HANDLED; + if (devctl & MUSB_DEVCTL_HM) { + if (is_host_capable()) + musb_host_rx(musb, ep_num); + } else { + if (is_peripheral_capable()) + musb_g_rx(musb, ep_num); + } + } + + reg >>= 1; + ep_num++; + } + + /* TX on endpoints 1-15 */ + reg = musb->int_tx >> 1; + ep_num = 1; + while (reg) { + if (reg & 1) { + /* musb_ep_select(musb->mregs, ep_num); */ + /* REVISIT just retval |= ep->tx_irq(...) */ + retval = IRQ_HANDLED; + if (devctl & MUSB_DEVCTL_HM) { + if (is_host_capable()) + musb_host_tx(musb, ep_num); + } else { + if (is_peripheral_capable()) + musb_g_tx(musb, ep_num); + } + } + reg >>= 1; + ep_num++; + } + + /* finish handling "global" interrupts after handling fifos */ + if (musb->int_usb) + retval |= musb_stage2_irq(musb, + musb->int_usb, devctl, power); + + return retval; +} + + +#ifndef CONFIG_MUSB_PIO_ONLY +static int __initdata use_dma = 1; + +/* "modprobe ... use_dma=0" etc */ +module_param(use_dma, bool, 0); +MODULE_PARM_DESC(use_dma, "enable/disable use of DMA"); + +void musb_dma_completion(struct musb *musb, u8 epnum, u8 transmit) +{ + u8 devctl = musb_readb(musb->mregs, MUSB_DEVCTL); + + /* called with controller lock already held */ + + if (!epnum) { +#ifndef CONFIG_USB_TUSB_OMAP_DMA + if (!is_cppi_enabled()) { + /* endpoint 0 */ + if (devctl & MUSB_DEVCTL_HM) + musb_h_ep0_irq(musb); + else + musb_g_ep0_irq(musb); + } +#endif + } else { + /* endpoints 1..15 */ + if (transmit) { + if (devctl & MUSB_DEVCTL_HM) { + if (is_host_capable()) + musb_host_tx(musb, epnum); + } else { + if (is_peripheral_capable()) + musb_g_tx(musb, epnum); + } + } else { + /* receive */ + if (devctl & MUSB_DEVCTL_HM) { + if (is_host_capable()) + musb_host_rx(musb, epnum); + } else { + if (is_peripheral_capable()) + musb_g_rx(musb, epnum); + } + } + } +} + +#else +#define use_dma 0 +#endif + +/*-------------------------------------------------------------------------*/ + +#ifdef CONFIG_SYSFS + +static ssize_t +musb_mode_show(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct musb *musb = dev_to_musb(dev); + unsigned long flags; + int ret = -EINVAL; + + spin_lock_irqsave(&musb->lock, flags); + ret = sprintf(buf, "%s\n", otg_state_string(musb)); + spin_unlock_irqrestore(&musb->lock, flags); + + return ret; +} + +static ssize_t +musb_mode_store(struct device *dev, struct device_attribute *attr, + const char *buf, size_t n) +{ + struct musb *musb = dev_to_musb(dev); + unsigned long flags; + + spin_lock_irqsave(&musb->lock, flags); + if (!strncmp(buf, "host", 4)) + musb_platform_set_mode(musb, MUSB_HOST); + if (!strncmp(buf, "peripheral", 10)) + musb_platform_set_mode(musb, MUSB_PERIPHERAL); + if (!strncmp(buf, "otg", 3)) + musb_platform_set_mode(musb, MUSB_OTG); + spin_unlock_irqrestore(&musb->lock, flags); + + return n; +} +static DEVICE_ATTR(mode, 0644, musb_mode_show, musb_mode_store); + +static ssize_t +musb_vbus_store(struct device *dev, struct device_attribute *attr, + const char *buf, size_t n) +{ + struct musb *musb = dev_to_musb(dev); + unsigned long flags; + unsigned long val; + + if (sscanf(buf, "%lu", &val) < 1) { + printk(KERN_ERR "Invalid VBUS timeout ms value\n"); + return -EINVAL; + } + + spin_lock_irqsave(&musb->lock, flags); + musb->a_wait_bcon = val; + if (musb->xceiv.state == OTG_STATE_A_WAIT_BCON) + musb->is_active = 0; + musb_platform_try_idle(musb, jiffies + msecs_to_jiffies(val)); + spin_unlock_irqrestore(&musb->lock, flags); + + return n; +} + +static ssize_t +musb_vbus_show(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct musb *musb = dev_to_musb(dev); + unsigned long flags; + unsigned long val; + int vbus; + + spin_lock_irqsave(&musb->lock, flags); + val = musb->a_wait_bcon; + vbus = musb_platform_get_vbus_status(musb); + spin_unlock_irqrestore(&musb->lock, flags); + + return sprintf(buf, "Vbus %s, timeout %lu\n", + vbus ? "on" : "off", val); +} +static DEVICE_ATTR(vbus, 0644, musb_vbus_show, musb_vbus_store); + +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + +/* Gadget drivers can't know that a host is connected so they might want + * to start SRP, but users can. This allows userspace to trigger SRP. + */ +static ssize_t +musb_srp_store(struct device *dev, struct device_attribute *attr, + const char *buf, size_t n) +{ + struct musb *musb = dev_to_musb(dev); + unsigned short srp; + + if (sscanf(buf, "%hu", &srp) != 1 + || (srp != 1)) { + printk(KERN_ERR "SRP: Value must be 1\n"); + return -EINVAL; + } + + if (srp == 1) + musb_g_wakeup(musb); + + return n; +} +static DEVICE_ATTR(srp, 0644, NULL, musb_srp_store); + +#endif /* CONFIG_USB_GADGET_MUSB_HDRC */ + +#endif /* sysfs */ + +/* Only used to provide driver mode change events */ +static void musb_irq_work(struct work_struct *data) +{ + struct musb *musb = container_of(data, struct musb, irq_work); + static int old_state; + + if (musb->xceiv.state != old_state) { + old_state = musb->xceiv.state; + sysfs_notify(&musb->controller->kobj, NULL, "mode"); + } +} + +/* -------------------------------------------------------------------------- + * Init support + */ + +static struct musb *__init +allocate_instance(struct device *dev, void __iomem *mbase) +{ + struct musb *musb; + struct musb_hw_ep *ep; + int epnum; +#ifdef CONFIG_USB_MUSB_HDRC_HCD + struct usb_hcd *hcd; + + hcd = usb_create_hcd(&musb_hc_driver, dev, dev->bus_id); + if (!hcd) + return NULL; + /* usbcore sets dev->driver_data to hcd, and sometimes uses that... */ + + musb = hcd_to_musb(hcd); + INIT_LIST_HEAD(&musb->control); + INIT_LIST_HEAD(&musb->in_bulk); + INIT_LIST_HEAD(&musb->out_bulk); + + hcd->uses_new_polling = 1; + + musb->vbuserr_retry = VBUSERR_RETRY_COUNT; +#else + musb = kzalloc(sizeof *musb, GFP_KERNEL); + if (!musb) + return NULL; + dev_set_drvdata(dev, musb); + +#endif + + musb->mregs = mbase; + musb->ctrl_base = mbase; + musb->nIrq = -ENODEV; + for (epnum = 0, ep = musb->endpoints; + epnum < MUSB_C_NUM_EPS; + epnum++, ep++) { + + ep->musb = musb; + ep->epnum = epnum; + } + + musb->controller = dev; + return musb; +} + +static void musb_free(struct musb *musb) +{ + /* this has multiple entry modes. it handles fault cleanup after + * probe(), where things may be partially set up, as well as rmmod + * cleanup after everything's been de-activated. + */ + +#ifdef CONFIG_SYSFS + device_remove_file(musb->controller, &dev_attr_mode); + device_remove_file(musb->controller, &dev_attr_vbus); +#ifdef CONFIG_USB_MUSB_OTG + device_remove_file(musb->controller, &dev_attr_srp); +#endif +#endif + +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + musb_gadget_cleanup(musb); +#endif + + if (musb->nIrq >= 0) { + disable_irq_wake(musb->nIrq); + free_irq(musb->nIrq, musb); + } + if (is_dma_capable() && musb->dma_controller) { + struct dma_controller *c = musb->dma_controller; + + (void) c->stop(c); + dma_controller_destroy(c); + } + + musb_writeb(musb->mregs, MUSB_DEVCTL, 0); + musb_platform_exit(musb); + musb_writeb(musb->mregs, MUSB_DEVCTL, 0); + + if (musb->clock) { + clk_disable(musb->clock); + clk_put(musb->clock); + } + +#ifdef CONFIG_USB_MUSB_OTG + put_device(musb->xceiv.dev); +#endif + +#ifdef CONFIG_USB_MUSB_HDRC_HCD + usb_put_hcd(musb_to_hcd(musb)); +#else + kfree(musb); +#endif +} + +/* + * Perform generic per-controller initialization. + * + * @pDevice: the controller (already clocked, etc) + * @nIrq: irq + * @mregs: virtual address of controller registers, + * not yet corrected for platform-specific offsets + */ +static int __init +musb_init_controller(struct device *dev, int nIrq, void __iomem *ctrl) +{ + int status; + struct musb *musb; + struct musb_hdrc_platform_data *plat = dev->platform_data; + + /* The driver might handle more features than the board; OK. + * Fail when the board needs a feature that's not enabled. + */ + if (!plat) { + dev_dbg(dev, "no platform_data?\n"); + return -ENODEV; + } + switch (plat->mode) { + case MUSB_HOST: +#ifdef CONFIG_USB_MUSB_HDRC_HCD + break; +#else + goto bad_config; +#endif + case MUSB_PERIPHERAL: +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + break; +#else + goto bad_config; +#endif + case MUSB_OTG: +#ifdef CONFIG_USB_MUSB_OTG + break; +#else +bad_config: +#endif + default: + dev_err(dev, "incompatible Kconfig role setting\n"); + return -EINVAL; + } + + /* allocate */ + musb = allocate_instance(dev, ctrl); + if (!musb) + return -ENOMEM; + + spin_lock_init(&musb->lock); + musb->board_mode = plat->mode; + musb->board_set_power = plat->set_power; + musb->set_clock = plat->set_clock; + musb->min_power = plat->min_power; + + /* Clock usage is chip-specific ... functional clock (DaVinci, + * OMAP2430), or PHY ref (some TUSB6010 boards). All this core + * code does is make sure a clock handle is available; platform + * code manages it during start/stop and suspend/resume. + */ + if (plat->clock) { + musb->clock = clk_get(dev, plat->clock); + if (IS_ERR(musb->clock)) { + status = PTR_ERR(musb->clock); + musb->clock = NULL; + goto fail; + } + } + + /* assume vbus is off */ + + /* platform adjusts musb->mregs and musb->isr if needed, + * and activates clocks + */ + musb->isr = generic_interrupt; + status = musb_platform_init(musb); + + if (status < 0) + goto fail; + if (!musb->isr) { + status = -ENODEV; + goto fail2; + } + +#ifndef CONFIG_MUSB_PIO_ONLY + if (use_dma && dev->dma_mask) { + struct dma_controller *c; + + c = dma_controller_create(musb, musb->mregs); + musb->dma_controller = c; + if (c) + (void) c->start(c); + } +#endif + /* ideally this would be abstracted in platform setup */ + if (!is_dma_capable() || !musb->dma_controller) + dev->dma_mask = NULL; + + /* be sure interrupts are disabled before connecting ISR */ + musb_platform_disable(musb); + musb_generic_disable(musb); + + /* setup musb parts of the core (especially endpoints) */ + status = musb_core_init(plat->multipoint + ? MUSB_CONTROLLER_MHDRC + : MUSB_CONTROLLER_HDRC, musb); + if (status < 0) + goto fail2; + + /* Init IRQ workqueue before request_irq */ + INIT_WORK(&musb->irq_work, musb_irq_work); + + /* attach to the IRQ */ + if (request_irq(nIrq, musb->isr, 0, dev->bus_id, musb)) { + dev_err(dev, "request_irq %d failed!\n", nIrq); + status = -ENODEV; + goto fail2; + } + musb->nIrq = nIrq; +/* FIXME this handles wakeup irqs wrong */ + if (enable_irq_wake(nIrq) == 0) + device_init_wakeup(dev, 1); + + pr_info("%s: USB %s mode controller at %p using %s, IRQ %d\n", + musb_driver_name, + ({char *s; + switch (musb->board_mode) { + case MUSB_HOST: s = "Host"; break; + case MUSB_PERIPHERAL: s = "Peripheral"; break; + default: s = "OTG"; break; + }; s; }), + ctrl, + (is_dma_capable() && musb->dma_controller) + ? "DMA" : "PIO", + musb->nIrq); + +#ifdef CONFIG_USB_MUSB_HDRC_HCD + /* host side needs more setup, except for no-host modes */ + if (musb->board_mode != MUSB_PERIPHERAL) { + struct usb_hcd *hcd = musb_to_hcd(musb); + + if (musb->board_mode == MUSB_OTG) + hcd->self.otg_port = 1; + musb->xceiv.host = &hcd->self; + hcd->power_budget = 2 * (plat->power ? : 250); + } +#endif /* CONFIG_USB_MUSB_HDRC_HCD */ + + /* For the host-only role, we can activate right away. + * (We expect the ID pin to be forcibly grounded!!) + * Otherwise, wait till the gadget driver hooks up. + */ + if (!is_otg_enabled(musb) && is_host_enabled(musb)) { + MUSB_HST_MODE(musb); + musb->xceiv.default_a = 1; + musb->xceiv.state = OTG_STATE_A_IDLE; + + status = usb_add_hcd(musb_to_hcd(musb), -1, 0); + + DBG(1, "%s mode, status %d, devctl %02x %c\n", + "HOST", status, + musb_readb(musb->mregs, MUSB_DEVCTL), + (musb_readb(musb->mregs, MUSB_DEVCTL) + & MUSB_DEVCTL_BDEVICE + ? 'B' : 'A')); + + } else /* peripheral is enabled */ { + MUSB_DEV_MODE(musb); + musb->xceiv.default_a = 0; + musb->xceiv.state = OTG_STATE_B_IDLE; + + status = musb_gadget_setup(musb); + + DBG(1, "%s mode, status %d, dev%02x\n", + is_otg_enabled(musb) ? "OTG" : "PERIPHERAL", + status, + musb_readb(musb->mregs, MUSB_DEVCTL)); + + } + + if (status == 0) + musb_debug_create("driver/musb_hdrc", musb); + else { +fail: + if (musb->clock) + clk_put(musb->clock); + device_init_wakeup(dev, 0); + musb_free(musb); + return status; + } + +#ifdef CONFIG_SYSFS + status = device_create_file(dev, &dev_attr_mode); + status = device_create_file(dev, &dev_attr_vbus); +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + status = device_create_file(dev, &dev_attr_srp); +#endif /* CONFIG_USB_GADGET_MUSB_HDRC */ + status = 0; +#endif + + return status; + +fail2: + musb_platform_exit(musb); + goto fail; +} + +/*-------------------------------------------------------------------------*/ + +/* all implementations (PCI bridge to FPGA, VLYNQ, etc) should just + * bridge to a platform device; this driver then suffices. + */ + +#ifndef CONFIG_MUSB_PIO_ONLY +static u64 *orig_dma_mask; +#endif + +static int __init musb_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + int irq = platform_get_irq(pdev, 0); + struct resource *iomem; + void __iomem *base; + + iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!iomem || irq == 0) + return -ENODEV; + + base = ioremap(iomem->start, iomem->end - iomem->start + 1); + if (!base) { + dev_err(dev, "ioremap failed\n"); + return -ENOMEM; + } + +#ifndef CONFIG_MUSB_PIO_ONLY + /* clobbered by use_dma=n */ + orig_dma_mask = dev->dma_mask; +#endif + return musb_init_controller(dev, irq, base); +} + +static int __devexit musb_remove(struct platform_device *pdev) +{ + struct musb *musb = dev_to_musb(&pdev->dev); + void __iomem *ctrl_base = musb->ctrl_base; + + /* this gets called on rmmod. + * - Host mode: host may still be active + * - Peripheral mode: peripheral is deactivated (or never-activated) + * - OTG mode: both roles are deactivated (or never-activated) + */ + musb_shutdown(pdev); + musb_debug_delete("driver/musb_hdrc", musb); +#ifdef CONFIG_USB_MUSB_HDRC_HCD + if (musb->board_mode == MUSB_HOST) + usb_remove_hcd(musb_to_hcd(musb)); +#endif + musb_free(musb); + iounmap(ctrl_base); + device_init_wakeup(&pdev->dev, 0); +#ifndef CONFIG_MUSB_PIO_ONLY + pdev->dev.dma_mask = orig_dma_mask; +#endif + return 0; +} + +#ifdef CONFIG_PM + +static int musb_suspend(struct platform_device *pdev, pm_message_t message) +{ + unsigned long flags; + struct musb *musb = dev_to_musb(&pdev->dev); + + if (!musb->clock) + return 0; + + spin_lock_irqsave(&musb->lock, flags); + + if (is_peripheral_active(musb)) { + /* FIXME force disconnect unless we know USB will wake + * the system up quickly enough to respond ... + */ + } else if (is_host_active(musb)) { + /* we know all the children are suspended; sometimes + * they will even be wakeup-enabled. + */ + } + + if (musb->set_clock) + musb->set_clock(musb->clock, 0); + else + clk_disable(musb->clock); + spin_unlock_irqrestore(&musb->lock, flags); + return 0; +} + +static int musb_resume(struct platform_device *pdev) +{ + unsigned long flags; + struct musb *musb = dev_to_musb(&pdev->dev); + + if (!musb->clock) + return 0; + + spin_lock_irqsave(&musb->lock, flags); + + if (musb->set_clock) + musb->set_clock(musb->clock, 1); + else + clk_enable(musb->clock); + + /* for static cmos like DaVinci, register values were preserved + * unless for some reason the whole soc powered down and we're + * not treating that as a whole-system restart (e.g. swsusp) + */ + spin_unlock_irqrestore(&musb->lock, flags); + return 0; +} + +#else +#define musb_suspend NULL +#define musb_resume NULL +#endif + +static struct platform_driver musb_driver = { + .driver = { + .name = (char *)musb_driver_name, + .bus = &platform_bus_type, + .owner = THIS_MODULE, + }, + .remove = __devexit_p(musb_remove), + .shutdown = musb_shutdown, + .suspend = musb_suspend, + .resume = musb_resume, +}; + +/*-------------------------------------------------------------------------*/ + +static int __init musb_init(void) +{ +#ifdef CONFIG_USB_MUSB_HDRC_HCD + if (usb_disabled()) + return 0; +#endif + + pr_info("%s: version " MUSB_VERSION ", " +#ifdef CONFIG_MUSB_PIO_ONLY + "pio" +#elif defined(CONFIG_USB_TI_CPPI_DMA) + "cppi-dma" +#elif defined(CONFIG_USB_INVENTRA_DMA) + "musb-dma" +#elif defined(CONFIG_USB_TUSB_OMAP_DMA) + "tusb-omap-dma" +#else + "?dma?" +#endif + ", " +#ifdef CONFIG_USB_MUSB_OTG + "otg (peripheral+host)" +#elif defined(CONFIG_USB_GADGET_MUSB_HDRC) + "peripheral" +#elif defined(CONFIG_USB_MUSB_HDRC_HCD) + "host" +#endif + ", debug=%d\n", + musb_driver_name, debug); + return platform_driver_probe(&musb_driver, musb_probe); +} + +/* make us init after usbcore and before usb + * gadget and host-side drivers start to register + */ +subsys_initcall(musb_init); + +static void __exit musb_cleanup(void) +{ + platform_driver_unregister(&musb_driver); +} +module_exit(musb_cleanup); diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h new file mode 100644 index 00000000000..90035c12ab5 --- /dev/null +++ b/drivers/usb/musb/musb_core.h @@ -0,0 +1,517 @@ +/* + * MUSB OTG driver defines + * + * Copyright 2005 Mentor Graphics Corporation + * Copyright (C) 2005-2006 by Texas Instruments + * Copyright (C) 2006-2007 Nokia Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + */ + +#ifndef __MUSB_CORE_H__ +#define __MUSB_CORE_H__ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +struct musb; +struct musb_hw_ep; +struct musb_ep; + + +#include "musb_debug.h" +#include "musb_dma.h" + +#ifdef CONFIG_USB_MUSB_SOC +/* + * Get core configuration from a header converted (by cfg_conv) + * from the Verilog config file generated by the core config utility + * + * For now we assume that header is provided along with other + * arch-specific files. Discrete chips will need a build tweak. + * So will using AHB IDs from silicon that provides them. + */ +#include +#endif + +#include "musb_io.h" +#include "musb_regs.h" + +#include "musb_gadget.h" +#include "../core/hcd.h" +#include "musb_host.h" + + + +#ifdef CONFIG_USB_MUSB_OTG + +#define is_peripheral_enabled(musb) ((musb)->board_mode != MUSB_HOST) +#define is_host_enabled(musb) ((musb)->board_mode != MUSB_PERIPHERAL) +#define is_otg_enabled(musb) ((musb)->board_mode == MUSB_OTG) + +/* NOTE: otg and peripheral-only state machines start at B_IDLE. + * OTG or host-only go to A_IDLE when ID is sensed. + */ +#define is_peripheral_active(m) (!(m)->is_host) +#define is_host_active(m) ((m)->is_host) + +#else +#define is_peripheral_enabled(musb) is_peripheral_capable() +#define is_host_enabled(musb) is_host_capable() +#define is_otg_enabled(musb) 0 + +#define is_peripheral_active(musb) is_peripheral_capable() +#define is_host_active(musb) is_host_capable() +#endif + +#if defined(CONFIG_USB_MUSB_OTG) || defined(CONFIG_USB_MUSB_PERIPHERAL) +/* for some reason, the "select USB_GADGET_MUSB_HDRC" doesn't always + * override that choice selection (often USB_GADGET_DUMMY_HCD). + */ +#ifndef CONFIG_USB_GADGET_MUSB_HDRC +#error bogus Kconfig output ... select CONFIG_USB_GADGET_MUSB_HDRC +#endif +#endif /* need MUSB gadget selection */ + + +#ifdef CONFIG_PROC_FS +#include +#define MUSB_CONFIG_PROC_FS +#endif + +/****************************** PERIPHERAL ROLE *****************************/ + +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + +#define is_peripheral_capable() (1) + +extern irqreturn_t musb_g_ep0_irq(struct musb *); +extern void musb_g_tx(struct musb *, u8); +extern void musb_g_rx(struct musb *, u8); +extern void musb_g_reset(struct musb *); +extern void musb_g_suspend(struct musb *); +extern void musb_g_resume(struct musb *); +extern void musb_g_wakeup(struct musb *); +extern void musb_g_disconnect(struct musb *); + +#else + +#define is_peripheral_capable() (0) + +static inline irqreturn_t musb_g_ep0_irq(struct musb *m) { return IRQ_NONE; } +static inline void musb_g_reset(struct musb *m) {} +static inline void musb_g_suspend(struct musb *m) {} +static inline void musb_g_resume(struct musb *m) {} +static inline void musb_g_wakeup(struct musb *m) {} +static inline void musb_g_disconnect(struct musb *m) {} + +#endif + +/****************************** HOST ROLE ***********************************/ + +#ifdef CONFIG_USB_MUSB_HDRC_HCD + +#define is_host_capable() (1) + +extern irqreturn_t musb_h_ep0_irq(struct musb *); +extern void musb_host_tx(struct musb *, u8); +extern void musb_host_rx(struct musb *, u8); + +#else + +#define is_host_capable() (0) + +static inline irqreturn_t musb_h_ep0_irq(struct musb *m) { return IRQ_NONE; } +static inline void musb_host_tx(struct musb *m, u8 e) {} +static inline void musb_host_rx(struct musb *m, u8 e) {} + +#endif + + +/****************************** CONSTANTS ********************************/ + +#ifndef MUSB_C_NUM_EPS +#define MUSB_C_NUM_EPS ((u8)16) +#endif + +#ifndef MUSB_MAX_END0_PACKET +#define MUSB_MAX_END0_PACKET ((u16)MUSB_EP0_FIFOSIZE) +#endif + +/* host side ep0 states */ +enum musb_h_ep0_state { + MUSB_EP0_IDLE, + MUSB_EP0_START, /* expect ack of setup */ + MUSB_EP0_IN, /* expect IN DATA */ + MUSB_EP0_OUT, /* expect ack of OUT DATA */ + MUSB_EP0_STATUS, /* expect ack of STATUS */ +} __attribute__ ((packed)); + +/* peripheral side ep0 states */ +enum musb_g_ep0_state { + MUSB_EP0_STAGE_SETUP, /* idle, waiting for setup */ + MUSB_EP0_STAGE_TX, /* IN data */ + MUSB_EP0_STAGE_RX, /* OUT data */ + MUSB_EP0_STAGE_STATUSIN, /* (after OUT data) */ + MUSB_EP0_STAGE_STATUSOUT, /* (after IN data) */ + MUSB_EP0_STAGE_ACKWAIT, /* after zlp, before statusin */ +} __attribute__ ((packed)); + +/* OTG protocol constants */ +#define OTG_TIME_A_WAIT_VRISE 100 /* msec (max) */ +#define OTG_TIME_A_WAIT_BCON 0 /* 0=infinite; min 1000 msec */ +#define OTG_TIME_A_IDLE_BDIS 200 /* msec (min) */ + +/*************************** REGISTER ACCESS ********************************/ + +/* Endpoint registers (other than dynfifo setup) can be accessed either + * directly with the "flat" model, or after setting up an index register. + */ + +#if defined(CONFIG_ARCH_DAVINCI) || defined(CONFIG_ARCH_OMAP2430) \ + || defined(CONFIG_ARCH_OMAP3430) +/* REVISIT indexed access seemed to + * misbehave (on DaVinci) for at least peripheral IN ... + */ +#define MUSB_FLAT_REG +#endif + +/* TUSB mapping: "flat" plus ep0 special cases */ +#if defined(CONFIG_USB_TUSB6010) +#define musb_ep_select(_mbase, _epnum) \ + musb_writeb((_mbase), MUSB_INDEX, (_epnum)) +#define MUSB_EP_OFFSET MUSB_TUSB_OFFSET + +/* "flat" mapping: each endpoint has its own i/o address */ +#elif defined(MUSB_FLAT_REG) +#define musb_ep_select(_mbase, _epnum) (((void)(_mbase)), ((void)(_epnum))) +#define MUSB_EP_OFFSET MUSB_FLAT_OFFSET + +/* "indexed" mapping: INDEX register controls register bank select */ +#else +#define musb_ep_select(_mbase, _epnum) \ + musb_writeb((_mbase), MUSB_INDEX, (_epnum)) +#define MUSB_EP_OFFSET MUSB_INDEXED_OFFSET +#endif + +/****************************** FUNCTIONS ********************************/ + +#define MUSB_HST_MODE(_musb)\ + { (_musb)->is_host = true; } +#define MUSB_DEV_MODE(_musb) \ + { (_musb)->is_host = false; } + +#define test_devctl_hst_mode(_x) \ + (musb_readb((_x)->mregs, MUSB_DEVCTL)&MUSB_DEVCTL_HM) + +#define MUSB_MODE(musb) ((musb)->is_host ? "Host" : "Peripheral") + +/******************************** TYPES *************************************/ + +/* + * struct musb_hw_ep - endpoint hardware (bidirectional) + * + * Ordered slightly for better cacheline locality. + */ +struct musb_hw_ep { + struct musb *musb; + void __iomem *fifo; + void __iomem *regs; + +#ifdef CONFIG_USB_TUSB6010 + void __iomem *conf; +#endif + + /* index in musb->endpoints[] */ + u8 epnum; + + /* hardware configuration, possibly dynamic */ + bool is_shared_fifo; + bool tx_double_buffered; + bool rx_double_buffered; + u16 max_packet_sz_tx; + u16 max_packet_sz_rx; + + struct dma_channel *tx_channel; + struct dma_channel *rx_channel; + +#ifdef CONFIG_USB_TUSB6010 + /* TUSB has "asynchronous" and "synchronous" dma modes */ + dma_addr_t fifo_async; + dma_addr_t fifo_sync; + void __iomem *fifo_sync_va; +#endif + +#ifdef CONFIG_USB_MUSB_HDRC_HCD + void __iomem *target_regs; + + /* currently scheduled peripheral endpoint */ + struct musb_qh *in_qh; + struct musb_qh *out_qh; + + u8 rx_reinit; + u8 tx_reinit; +#endif + +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + /* peripheral side */ + struct musb_ep ep_in; /* TX */ + struct musb_ep ep_out; /* RX */ +#endif +}; + +static inline struct usb_request *next_in_request(struct musb_hw_ep *hw_ep) +{ +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + return next_request(&hw_ep->ep_in); +#else + return NULL; +#endif +} + +static inline struct usb_request *next_out_request(struct musb_hw_ep *hw_ep) +{ +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + return next_request(&hw_ep->ep_out); +#else + return NULL; +#endif +} + +/* + * struct musb - Driver instance data. + */ +struct musb { + /* device lock */ + spinlock_t lock; + struct clk *clock; + irqreturn_t (*isr)(int, void *); + struct work_struct irq_work; + +/* this hub status bit is reserved by USB 2.0 and not seen by usbcore */ +#define MUSB_PORT_STAT_RESUME (1 << 31) + + u32 port1_status; + +#ifdef CONFIG_USB_MUSB_HDRC_HCD + unsigned long rh_timer; + + enum musb_h_ep0_state ep0_stage; + + /* bulk traffic normally dedicates endpoint hardware, and each + * direction has its own ring of host side endpoints. + * we try to progress the transfer at the head of each endpoint's + * queue until it completes or NAKs too much; then we try the next + * endpoint. + */ + struct musb_hw_ep *bulk_ep; + + struct list_head control; /* of musb_qh */ + struct list_head in_bulk; /* of musb_qh */ + struct list_head out_bulk; /* of musb_qh */ + struct musb_qh *periodic[32]; /* tree of interrupt+iso */ +#endif + + /* called with IRQs blocked; ON/nonzero implies starting a session, + * and waiting at least a_wait_vrise_tmout. + */ + void (*board_set_vbus)(struct musb *, int is_on); + + struct dma_controller *dma_controller; + + struct device *controller; + void __iomem *ctrl_base; + void __iomem *mregs; + +#ifdef CONFIG_USB_TUSB6010 + dma_addr_t async; + dma_addr_t sync; + void __iomem *sync_va; +#endif + + /* passed down from chip/board specific irq handlers */ + u8 int_usb; + u16 int_rx; + u16 int_tx; + + struct otg_transceiver xceiv; + + int nIrq; + + struct musb_hw_ep endpoints[MUSB_C_NUM_EPS]; +#define control_ep endpoints + +#define VBUSERR_RETRY_COUNT 3 + u16 vbuserr_retry; + u16 epmask; + u8 nr_endpoints; + + u8 board_mode; /* enum musb_mode */ + int (*board_set_power)(int state); + + int (*set_clock)(struct clk *clk, int is_active); + + u8 min_power; /* vbus for periph, in mA/2 */ + + bool is_host; + + int a_wait_bcon; /* VBUS timeout in msecs */ + unsigned long idle_timeout; /* Next timeout in jiffies */ + + /* active means connected and not suspended */ + unsigned is_active:1; + + unsigned is_multipoint:1; + unsigned ignore_disconnect:1; /* during bus resets */ + +#ifdef C_MP_TX + unsigned bulk_split:1; +#define can_bulk_split(musb,type) \ + (((type) == USB_ENDPOINT_XFER_BULK) && (musb)->bulk_split) +#else +#define can_bulk_split(musb, type) 0 +#endif + +#ifdef C_MP_RX + unsigned bulk_combine:1; +#define can_bulk_combine(musb,type) \ + (((type) == USB_ENDPOINT_XFER_BULK) && (musb)->bulk_combine) +#else +#define can_bulk_combine(musb, type) 0 +#endif + +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + /* is_suspended means USB B_PERIPHERAL suspend */ + unsigned is_suspended:1; + + /* may_wakeup means remote wakeup is enabled */ + unsigned may_wakeup:1; + + /* is_self_powered is reported in device status and the + * config descriptor. is_bus_powered means B_PERIPHERAL + * draws some VBUS current; both can be true. + */ + unsigned is_self_powered:1; + unsigned is_bus_powered:1; + + unsigned set_address:1; + unsigned test_mode:1; + unsigned softconnect:1; + + u8 address; + u8 test_mode_nr; + u16 ackpend; /* ep0 */ + enum musb_g_ep0_state ep0_state; + struct usb_gadget g; /* the gadget */ + struct usb_gadget_driver *gadget_driver; /* its driver */ +#endif + +#ifdef MUSB_CONFIG_PROC_FS + struct proc_dir_entry *proc_entry; +#endif +}; + +static inline void musb_set_vbus(struct musb *musb, int is_on) +{ + musb->board_set_vbus(musb, is_on); +} + +#ifdef CONFIG_USB_GADGET_MUSB_HDRC +static inline struct musb *gadget_to_musb(struct usb_gadget *g) +{ + return container_of(g, struct musb, g); +} +#endif + + +/***************************** Glue it together *****************************/ + +extern const char musb_driver_name[]; + +extern void musb_start(struct musb *musb); +extern void musb_stop(struct musb *musb); + +extern void musb_write_fifo(struct musb_hw_ep *ep, u16 len, const u8 *src); +extern void musb_read_fifo(struct musb_hw_ep *ep, u16 len, u8 *dst); + +extern void musb_load_testpacket(struct musb *); + +extern irqreturn_t musb_interrupt(struct musb *); + +extern void musb_platform_enable(struct musb *musb); +extern void musb_platform_disable(struct musb *musb); + +extern void musb_hnp_stop(struct musb *musb); + +extern void musb_platform_set_mode(struct musb *musb, u8 musb_mode); + +#if defined(CONFIG_USB_TUSB6010) || \ + defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP34XX) +extern void musb_platform_try_idle(struct musb *musb, unsigned long timeout); +#else +#define musb_platform_try_idle(x, y) do {} while (0) +#endif + +#ifdef CONFIG_USB_TUSB6010 +extern int musb_platform_get_vbus_status(struct musb *musb); +#else +#define musb_platform_get_vbus_status(x) 0 +#endif + +extern int __init musb_platform_init(struct musb *musb); +extern int musb_platform_exit(struct musb *musb); + +/*-------------------------- ProcFS definitions ---------------------*/ + +struct proc_dir_entry; + +#if (MUSB_DEBUG > 0) && defined(MUSB_CONFIG_PROC_FS) +extern struct proc_dir_entry *musb_debug_create(char *name, struct musb *data); +extern void musb_debug_delete(char *name, struct musb *data); + +#else +static inline struct proc_dir_entry * +musb_debug_create(char *name, struct musb *data) +{ + return NULL; +} +static inline void musb_debug_delete(char *name, struct musb *data) +{ +} +#endif + +#endif /* __MUSB_CORE_H__ */ diff --git a/drivers/usb/musb/musb_debug.h b/drivers/usb/musb/musb_debug.h new file mode 100644 index 00000000000..3bdb311e820 --- /dev/null +++ b/drivers/usb/musb/musb_debug.h @@ -0,0 +1,66 @@ +/* + * MUSB OTG driver debug defines + * + * Copyright 2005 Mentor Graphics Corporation + * Copyright (C) 2005-2006 by Texas Instruments + * Copyright (C) 2006-2007 Nokia Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + */ + +#ifndef __MUSB_LINUX_DEBUG_H__ +#define __MUSB_LINUX_DEBUG_H__ + +#define yprintk(facility, format, args...) \ + do { printk(facility "%s %d: " format , \ + __func__, __LINE__ , ## args); } while (0) +#define WARNING(fmt, args...) yprintk(KERN_WARNING, fmt, ## args) +#define INFO(fmt, args...) yprintk(KERN_INFO, fmt, ## args) +#define ERR(fmt, args...) yprintk(KERN_ERR, fmt, ## args) + +#define xprintk(level, facility, format, args...) do { \ + if (_dbg_level(level)) { \ + printk(facility "%s %d: " format , \ + __func__, __LINE__ , ## args); \ + } } while (0) + +#if MUSB_DEBUG > 0 +extern unsigned debug; +#else +#define debug 0 +#endif + +static inline int _dbg_level(unsigned l) +{ + return debug >= l; +} + +#define DBG(level, fmt, args...) xprintk(level, KERN_DEBUG, fmt, ## args) + +extern const char *otg_state_string(struct musb *); + +#endif /* __MUSB_LINUX_DEBUG_H__ */ diff --git a/drivers/usb/musb/musb_dma.h b/drivers/usb/musb/musb_dma.h new file mode 100644 index 00000000000..0a2c4e3602c --- /dev/null +++ b/drivers/usb/musb/musb_dma.h @@ -0,0 +1,172 @@ +/* + * MUSB OTG driver DMA controller abstraction + * + * Copyright 2005 Mentor Graphics Corporation + * Copyright (C) 2005-2006 by Texas Instruments + * Copyright (C) 2006-2007 Nokia Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + */ + +#ifndef __MUSB_DMA_H__ +#define __MUSB_DMA_H__ + +struct musb_hw_ep; + +/* + * DMA Controller Abstraction + * + * DMA Controllers are abstracted to allow use of a variety of different + * implementations of DMA, as allowed by the Inventra USB cores. On the + * host side, usbcore sets up the DMA mappings and flushes caches; on the + * peripheral side, the gadget controller driver does. Responsibilities + * of a DMA controller driver include: + * + * - Handling the details of moving multiple USB packets + * in cooperation with the Inventra USB core, including especially + * the correct RX side treatment of short packets and buffer-full + * states (both of which terminate transfers). + * + * - Knowing the correlation between dma channels and the + * Inventra core's local endpoint resources and data direction. + * + * - Maintaining a list of allocated/available channels. + * + * - Updating channel status on interrupts, + * whether shared with the Inventra core or separate. + */ + +#define DMA_ADDR_INVALID (~(dma_addr_t)0) + +#ifndef CONFIG_MUSB_PIO_ONLY +#define is_dma_capable() (1) +#else +#define is_dma_capable() (0) +#endif + +#ifdef CONFIG_USB_TI_CPPI_DMA +#define is_cppi_enabled() 1 +#else +#define is_cppi_enabled() 0 +#endif + +#ifdef CONFIG_USB_TUSB_OMAP_DMA +#define tusb_dma_omap() 1 +#else +#define tusb_dma_omap() 0 +#endif + +/* + * DMA channel status ... updated by the dma controller driver whenever that + * status changes, and protected by the overall controller spinlock. + */ +enum dma_channel_status { + /* unallocated */ + MUSB_DMA_STATUS_UNKNOWN, + /* allocated ... but not busy, no errors */ + MUSB_DMA_STATUS_FREE, + /* busy ... transactions are active */ + MUSB_DMA_STATUS_BUSY, + /* transaction(s) aborted due to ... dma or memory bus error */ + MUSB_DMA_STATUS_BUS_ABORT, + /* transaction(s) aborted due to ... core error or USB fault */ + MUSB_DMA_STATUS_CORE_ABORT +}; + +struct dma_controller; + +/** + * struct dma_channel - A DMA channel. + * @private_data: channel-private data + * @max_len: the maximum number of bytes the channel can move in one + * transaction (typically representing many USB maximum-sized packets) + * @actual_len: how many bytes have been transferred + * @status: current channel status (updated e.g. on interrupt) + * @desired_mode: true if mode 1 is desired; false if mode 0 is desired + * + * channels are associated with an endpoint for the duration of at least + * one usb transfer. + */ +struct dma_channel { + void *private_data; + /* FIXME not void* private_data, but a dma_controller * */ + size_t max_len; + size_t actual_len; + enum dma_channel_status status; + bool desired_mode; +}; + +/* + * dma_channel_status - return status of dma channel + * @c: the channel + * + * Returns the software's view of the channel status. If that status is BUSY + * then it's possible that the hardware has completed (or aborted) a transfer, + * so the driver needs to update that status. + */ +static inline enum dma_channel_status +dma_channel_status(struct dma_channel *c) +{ + return (is_dma_capable() && c) ? c->status : MUSB_DMA_STATUS_UNKNOWN; +} + +/** + * struct dma_controller - A DMA Controller. + * @start: call this to start a DMA controller; + * return 0 on success, else negative errno + * @stop: call this to stop a DMA controller + * return 0 on success, else negative errno + * @channel_alloc: call this to allocate a DMA channel + * @channel_release: call this to release a DMA channel + * @channel_abort: call this to abort a pending DMA transaction, + * returning it to FREE (but allocated) state + * + * Controllers manage dma channels. + */ +struct dma_controller { + int (*start)(struct dma_controller *); + int (*stop)(struct dma_controller *); + struct dma_channel *(*channel_alloc)(struct dma_controller *, + struct musb_hw_ep *, u8 is_tx); + void (*channel_release)(struct dma_channel *); + int (*channel_program)(struct dma_channel *channel, + u16 maxpacket, u8 mode, + dma_addr_t dma_addr, + u32 length); + int (*channel_abort)(struct dma_channel *); +}; + +/* called after channel_program(), may indicate a fault */ +extern void musb_dma_completion(struct musb *musb, u8 epnum, u8 transmit); + + +extern struct dma_controller *__init +dma_controller_create(struct musb *, void __iomem *); + +extern void dma_controller_destroy(struct dma_controller *); + +#endif /* __MUSB_DMA_H__ */ diff --git a/drivers/usb/musb/musb_gadget.c b/drivers/usb/musb/musb_gadget.c new file mode 100644 index 00000000000..b3773f13ee0 --- /dev/null +++ b/drivers/usb/musb/musb_gadget.c @@ -0,0 +1,2033 @@ +/* + * MUSB OTG driver peripheral support + * + * Copyright 2005 Mentor Graphics Corporation + * Copyright (C) 2005-2006 by Texas Instruments + * Copyright (C) 2006-2007 Nokia Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "musb_core.h" + + +/* MUSB PERIPHERAL status 3-mar-2006: + * + * - EP0 seems solid. It passes both USBCV and usbtest control cases. + * Minor glitches: + * + * + remote wakeup to Linux hosts work, but saw USBCV failures; + * in one test run (operator error?) + * + endpoint halt tests -- in both usbtest and usbcv -- seem + * to break when dma is enabled ... is something wrongly + * clearing SENDSTALL? + * + * - Mass storage behaved ok when last tested. Network traffic patterns + * (with lots of short transfers etc) need retesting; they turn up the + * worst cases of the DMA, since short packets are typical but are not + * required. + * + * - TX/IN + * + both pio and dma behave in with network and g_zero tests + * + no cppi throughput issues other than no-hw-queueing + * + failed with FLAT_REG (DaVinci) + * + seems to behave with double buffering, PIO -and- CPPI + * + with gadgetfs + AIO, requests got lost? + * + * - RX/OUT + * + both pio and dma behave in with network and g_zero tests + * + dma is slow in typical case (short_not_ok is clear) + * + double buffering ok with PIO + * + double buffering *FAILS* with CPPI, wrong data bytes sometimes + * + request lossage observed with gadgetfs + * + * - ISO not tested ... might work, but only weakly isochronous + * + * - Gadget driver disabling of softconnect during bind() is ignored; so + * drivers can't hold off host requests until userspace is ready. + * (Workaround: they can turn it off later.) + * + * - PORTABILITY (assumes PIO works): + * + DaVinci, basically works with cppi dma + * + OMAP 2430, ditto with mentor dma + * + TUSB 6010, platform-specific dma in the works + */ + +/* ----------------------------------------------------------------------- */ + +/* + * Immediately complete a request. + * + * @param request the request to complete + * @param status the status to complete the request with + * Context: controller locked, IRQs blocked. + */ +void musb_g_giveback( + struct musb_ep *ep, + struct usb_request *request, + int status) +__releases(ep->musb->lock) +__acquires(ep->musb->lock) +{ + struct musb_request *req; + struct musb *musb; + int busy = ep->busy; + + req = to_musb_request(request); + + list_del(&request->list); + if (req->request.status == -EINPROGRESS) + req->request.status = status; + musb = req->musb; + + ep->busy = 1; + spin_unlock(&musb->lock); + if (is_dma_capable()) { + if (req->mapped) { + dma_unmap_single(musb->controller, + req->request.dma, + req->request.length, + req->tx + ? DMA_TO_DEVICE + : DMA_FROM_DEVICE); + req->request.dma = DMA_ADDR_INVALID; + req->mapped = 0; + } else if (req->request.dma != DMA_ADDR_INVALID) + dma_sync_single_for_cpu(musb->controller, + req->request.dma, + req->request.length, + req->tx + ? DMA_TO_DEVICE + : DMA_FROM_DEVICE); + } + if (request->status == 0) + DBG(5, "%s done request %p, %d/%d\n", + ep->end_point.name, request, + req->request.actual, req->request.length); + else + DBG(2, "%s request %p, %d/%d fault %d\n", + ep->end_point.name, request, + req->request.actual, req->request.length, + request->status); + req->request.complete(&req->ep->end_point, &req->request); + spin_lock(&musb->lock); + ep->busy = busy; +} + +/* ----------------------------------------------------------------------- */ + +/* + * Abort requests queued to an endpoint using the status. Synchronous. + * caller locked controller and blocked irqs, and selected this ep. + */ +static void nuke(struct musb_ep *ep, const int status) +{ + struct musb_request *req = NULL; + void __iomem *epio = ep->musb->endpoints[ep->current_epnum].regs; + + ep->busy = 1; + + if (is_dma_capable() && ep->dma) { + struct dma_controller *c = ep->musb->dma_controller; + int value; + if (ep->is_in) { + musb_writew(epio, MUSB_TXCSR, + 0 | MUSB_TXCSR_FLUSHFIFO); + musb_writew(epio, MUSB_TXCSR, + 0 | MUSB_TXCSR_FLUSHFIFO); + } else { + musb_writew(epio, MUSB_RXCSR, + 0 | MUSB_RXCSR_FLUSHFIFO); + musb_writew(epio, MUSB_RXCSR, + 0 | MUSB_RXCSR_FLUSHFIFO); + } + + value = c->channel_abort(ep->dma); + DBG(value ? 1 : 6, "%s: abort DMA --> %d\n", ep->name, value); + c->channel_release(ep->dma); + ep->dma = NULL; + } + + while (!list_empty(&(ep->req_list))) { + req = container_of(ep->req_list.next, struct musb_request, + request.list); + musb_g_giveback(ep, &req->request, status); + } +} + +/* ----------------------------------------------------------------------- */ + +/* Data transfers - pure PIO, pure DMA, or mixed mode */ + +/* + * This assumes the separate CPPI engine is responding to DMA requests + * from the usb core ... sequenced a bit differently from mentor dma. + */ + +static inline int max_ep_writesize(struct musb *musb, struct musb_ep *ep) +{ + if (can_bulk_split(musb, ep->type)) + return ep->hw_ep->max_packet_sz_tx; + else + return ep->packet_sz; +} + + +#ifdef CONFIG_USB_INVENTRA_DMA + +/* Peripheral tx (IN) using Mentor DMA works as follows: + Only mode 0 is used for transfers <= wPktSize, + mode 1 is used for larger transfers, + + One of the following happens: + - Host sends IN token which causes an endpoint interrupt + -> TxAvail + -> if DMA is currently busy, exit. + -> if queue is non-empty, txstate(). + + - Request is queued by the gadget driver. + -> if queue was previously empty, txstate() + + txstate() + -> start + /\ -> setup DMA + | (data is transferred to the FIFO, then sent out when + | IN token(s) are recd from Host. + | -> DMA interrupt on completion + | calls TxAvail. + | -> stop DMA, ~DmaEenab, + | -> set TxPktRdy for last short pkt or zlp + | -> Complete Request + | -> Continue next request (call txstate) + |___________________________________| + + * Non-Mentor DMA engines can of course work differently, such as by + * upleveling from irq-per-packet to irq-per-buffer. + */ + +#endif + +/* + * An endpoint is transmitting data. This can be called either from + * the IRQ routine or from ep.queue() to kickstart a request on an + * endpoint. + * + * Context: controller locked, IRQs blocked, endpoint selected + */ +static void txstate(struct musb *musb, struct musb_request *req) +{ + u8 epnum = req->epnum; + struct musb_ep *musb_ep; + void __iomem *epio = musb->endpoints[epnum].regs; + struct usb_request *request; + u16 fifo_count = 0, csr; + int use_dma = 0; + + musb_ep = req->ep; + + /* we shouldn't get here while DMA is active ... but we do ... */ + if (dma_channel_status(musb_ep->dma) == MUSB_DMA_STATUS_BUSY) { + DBG(4, "dma pending...\n"); + return; + } + + /* read TXCSR before */ + csr = musb_readw(epio, MUSB_TXCSR); + + request = &req->request; + fifo_count = min(max_ep_writesize(musb, musb_ep), + (int)(request->length - request->actual)); + + if (csr & MUSB_TXCSR_TXPKTRDY) { + DBG(5, "%s old packet still ready , txcsr %03x\n", + musb_ep->end_point.name, csr); + return; + } + + if (csr & MUSB_TXCSR_P_SENDSTALL) { + DBG(5, "%s stalling, txcsr %03x\n", + musb_ep->end_point.name, csr); + return; + } + + DBG(4, "hw_ep%d, maxpacket %d, fifo count %d, txcsr %03x\n", + epnum, musb_ep->packet_sz, fifo_count, + csr); + +#ifndef CONFIG_MUSB_PIO_ONLY + if (is_dma_capable() && musb_ep->dma) { + struct dma_controller *c = musb->dma_controller; + + use_dma = (request->dma != DMA_ADDR_INVALID); + + /* MUSB_TXCSR_P_ISO is still set correctly */ + +#ifdef CONFIG_USB_INVENTRA_DMA + { + size_t request_size; + + /* setup DMA, then program endpoint CSR */ + request_size = min(request->length, + musb_ep->dma->max_len); + if (request_size <= musb_ep->packet_sz) + musb_ep->dma->desired_mode = 0; + else + musb_ep->dma->desired_mode = 1; + + use_dma = use_dma && c->channel_program( + musb_ep->dma, musb_ep->packet_sz, + musb_ep->dma->desired_mode, + request->dma, request_size); + if (use_dma) { + if (musb_ep->dma->desired_mode == 0) { + /* ASSERT: DMAENAB is clear */ + csr &= ~(MUSB_TXCSR_AUTOSET | + MUSB_TXCSR_DMAMODE); + csr |= (MUSB_TXCSR_DMAENAB | + MUSB_TXCSR_MODE); + /* against programming guide */ + } else + csr |= (MUSB_TXCSR_AUTOSET + | MUSB_TXCSR_DMAENAB + | MUSB_TXCSR_DMAMODE + | MUSB_TXCSR_MODE); + + csr &= ~MUSB_TXCSR_P_UNDERRUN; + musb_writew(epio, MUSB_TXCSR, csr); + } + } + +#elif defined(CONFIG_USB_TI_CPPI_DMA) + /* program endpoint CSR first, then setup DMA */ + csr &= ~(MUSB_TXCSR_AUTOSET + | MUSB_TXCSR_DMAMODE + | MUSB_TXCSR_P_UNDERRUN + | MUSB_TXCSR_TXPKTRDY); + csr |= MUSB_TXCSR_MODE | MUSB_TXCSR_DMAENAB; + musb_writew(epio, MUSB_TXCSR, + (MUSB_TXCSR_P_WZC_BITS & ~MUSB_TXCSR_P_UNDERRUN) + | csr); + + /* ensure writebuffer is empty */ + csr = musb_readw(epio, MUSB_TXCSR); + + /* NOTE host side sets DMAENAB later than this; both are + * OK since the transfer dma glue (between CPPI and Mentor + * fifos) just tells CPPI it could start. Data only moves + * to the USB TX fifo when both fifos are ready. + */ + + /* "mode" is irrelevant here; handle terminating ZLPs like + * PIO does, since the hardware RNDIS mode seems unreliable + * except for the last-packet-is-already-short case. + */ + use_dma = use_dma && c->channel_program( + musb_ep->dma, musb_ep->packet_sz, + 0, + request->dma, + request->length); + if (!use_dma) { + c->channel_release(musb_ep->dma); + musb_ep->dma = NULL; + /* ASSERT: DMAENAB clear */ + csr &= ~(MUSB_TXCSR_DMAMODE | MUSB_TXCSR_MODE); + /* invariant: prequest->buf is non-null */ + } +#elif defined(CONFIG_USB_TUSB_OMAP_DMA) + use_dma = use_dma && c->channel_program( + musb_ep->dma, musb_ep->packet_sz, + request->zero, + request->dma, + request->length); +#endif + } +#endif + + if (!use_dma) { + musb_write_fifo(musb_ep->hw_ep, fifo_count, + (u8 *) (request->buf + request->actual)); + request->actual += fifo_count; + csr |= MUSB_TXCSR_TXPKTRDY; + csr &= ~MUSB_TXCSR_P_UNDERRUN; + musb_writew(epio, MUSB_TXCSR, csr); + } + + /* host may already have the data when this message shows... */ + DBG(3, "%s TX/IN %s len %d/%d, txcsr %04x, fifo %d/%d\n", + musb_ep->end_point.name, use_dma ? "dma" : "pio", + request->actual, request->length, + musb_readw(epio, MUSB_TXCSR), + fifo_count, + musb_readw(epio, MUSB_TXMAXP)); +} + +/* + * FIFO state update (e.g. data ready). + * Called from IRQ, with controller locked. + */ +void musb_g_tx(struct musb *musb, u8 epnum) +{ + u16 csr; + struct usb_request *request; + u8 __iomem *mbase = musb->mregs; + struct musb_ep *musb_ep = &musb->endpoints[epnum].ep_in; + void __iomem *epio = musb->endpoints[epnum].regs; + struct dma_channel *dma; + + musb_ep_select(mbase, epnum); + request = next_request(musb_ep); + + csr = musb_readw(epio, MUSB_TXCSR); + DBG(4, "<== %s, txcsr %04x\n", musb_ep->end_point.name, csr); + + dma = is_dma_capable() ? musb_ep->dma : NULL; + do { + /* REVISIT for high bandwidth, MUSB_TXCSR_P_INCOMPTX + * probably rates reporting as a host error + */ + if (csr & MUSB_TXCSR_P_SENTSTALL) { + csr |= MUSB_TXCSR_P_WZC_BITS; + csr &= ~MUSB_TXCSR_P_SENTSTALL; + musb_writew(epio, MUSB_TXCSR, csr); + if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) { + dma->status = MUSB_DMA_STATUS_CORE_ABORT; + musb->dma_controller->channel_abort(dma); + } + + if (request) + musb_g_giveback(musb_ep, request, -EPIPE); + + break; + } + + if (csr & MUSB_TXCSR_P_UNDERRUN) { + /* we NAKed, no big deal ... little reason to care */ + csr |= MUSB_TXCSR_P_WZC_BITS; + csr &= ~(MUSB_TXCSR_P_UNDERRUN + | MUSB_TXCSR_TXPKTRDY); + musb_writew(epio, MUSB_TXCSR, csr); + DBG(20, "underrun on ep%d, req %p\n", epnum, request); + } + + if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) { + /* SHOULD NOT HAPPEN ... has with cppi though, after + * changing SENDSTALL (and other cases); harmless? + */ + DBG(5, "%s dma still busy?\n", musb_ep->end_point.name); + break; + } + + if (request) { + u8 is_dma = 0; + + if (dma && (csr & MUSB_TXCSR_DMAENAB)) { + is_dma = 1; + csr |= MUSB_TXCSR_P_WZC_BITS; + csr &= ~(MUSB_TXCSR_DMAENAB + | MUSB_TXCSR_P_UNDERRUN + | MUSB_TXCSR_TXPKTRDY); + musb_writew(epio, MUSB_TXCSR, csr); + /* ensure writebuffer is empty */ + csr = musb_readw(epio, MUSB_TXCSR); + request->actual += musb_ep->dma->actual_len; + DBG(4, "TXCSR%d %04x, dma off, " + "len %zu, req %p\n", + epnum, csr, + musb_ep->dma->actual_len, + request); + } + + if (is_dma || request->actual == request->length) { + + /* First, maybe a terminating short packet. + * Some DMA engines might handle this by + * themselves. + */ + if ((request->zero + && request->length + && (request->length + % musb_ep->packet_sz) + == 0) +#ifdef CONFIG_USB_INVENTRA_DMA + || (is_dma && + ((!dma->desired_mode) || + (request->actual & + (musb_ep->packet_sz - 1)))) +#endif + ) { + /* on dma completion, fifo may not + * be available yet ... + */ + if (csr & MUSB_TXCSR_TXPKTRDY) + break; + + DBG(4, "sending zero pkt\n"); + musb_writew(epio, MUSB_TXCSR, + MUSB_TXCSR_MODE + | MUSB_TXCSR_TXPKTRDY); + request->zero = 0; + } + + /* ... or if not, then complete it */ + musb_g_giveback(musb_ep, request, 0); + + /* kickstart next transfer if appropriate; + * the packet that just completed might not + * be transmitted for hours or days. + * REVISIT for double buffering... + * FIXME revisit for stalls too... + */ + musb_ep_select(mbase, epnum); + csr = musb_readw(epio, MUSB_TXCSR); + if (csr & MUSB_TXCSR_FIFONOTEMPTY) + break; + request = musb_ep->desc + ? next_request(musb_ep) + : NULL; + if (!request) { + DBG(4, "%s idle now\n", + musb_ep->end_point.name); + break; + } + } + + txstate(musb, to_musb_request(request)); + } + + } while (0); +} + +/* ------------------------------------------------------------ */ + +#ifdef CONFIG_USB_INVENTRA_DMA + +/* Peripheral rx (OUT) using Mentor DMA works as follows: + - Only mode 0 is used. + + - Request is queued by the gadget class driver. + -> if queue was previously empty, rxstate() + + - Host sends OUT token which causes an endpoint interrupt + /\ -> RxReady + | -> if request queued, call rxstate + | /\ -> setup DMA + | | -> DMA interrupt on completion + | | -> RxReady + | | -> stop DMA + | | -> ack the read + | | -> if data recd = max expected + | | by the request, or host + | | sent a short packet, + | | complete the request, + | | and start the next one. + | |_____________________________________| + | else just wait for the host + | to send the next OUT token. + |__________________________________________________| + + * Non-Mentor DMA engines can of course work differently. + */ + +#endif + +/* + * Context: controller locked, IRQs blocked, endpoint selected + */ +static void rxstate(struct musb *musb, struct musb_request *req) +{ + u16 csr = 0; + const u8 epnum = req->epnum; + struct usb_request *request = &req->request; + struct musb_ep *musb_ep = &musb->endpoints[epnum].ep_out; + void __iomem *epio = musb->endpoints[epnum].regs; + u16 fifo_count = 0; + u16 len = musb_ep->packet_sz; + + csr = musb_readw(epio, MUSB_RXCSR); + + if (is_cppi_enabled() && musb_ep->dma) { + struct dma_controller *c = musb->dma_controller; + struct dma_channel *channel = musb_ep->dma; + + /* NOTE: CPPI won't actually stop advancing the DMA + * queue after short packet transfers, so this is almost + * always going to run as IRQ-per-packet DMA so that + * faults will be handled correctly. + */ + if (c->channel_program(channel, + musb_ep->packet_sz, + !request->short_not_ok, + request->dma + request->actual, + request->length - request->actual)) { + + /* make sure that if an rxpkt arrived after the irq, + * the cppi engine will be ready to take it as soon + * as DMA is enabled + */ + csr &= ~(MUSB_RXCSR_AUTOCLEAR + | MUSB_RXCSR_DMAMODE); + csr |= MUSB_RXCSR_DMAENAB | MUSB_RXCSR_P_WZC_BITS; + musb_writew(epio, MUSB_RXCSR, csr); + return; + } + } + + if (csr & MUSB_RXCSR_RXPKTRDY) { + len = musb_readw(epio, MUSB_RXCOUNT); + if (request->actual < request->length) { +#ifdef CONFIG_USB_INVENTRA_DMA + if (is_dma_capable() && musb_ep->dma) { + struct dma_controller *c; + struct dma_channel *channel; + int use_dma = 0; + + c = musb->dma_controller; + channel = musb_ep->dma; + + /* We use DMA Req mode 0 in rx_csr, and DMA controller operates in + * mode 0 only. So we do not get endpoint interrupts due to DMA + * completion. We only get interrupts from DMA controller. + * + * We could operate in DMA mode 1 if we knew the size of the tranfer + * in advance. For mass storage class, request->length = what the host + * sends, so that'd work. But for pretty much everything else, + * request->length is routinely more than what the host sends. For + * most these gadgets, end of is signified either by a short packet, + * or filling the last byte of the buffer. (Sending extra data in + * that last pckate should trigger an overflow fault.) But in mode 1, + * we don't get DMA completion interrrupt for short packets. + * + * Theoretically, we could enable DMAReq irq (MUSB_RXCSR_DMAMODE = 1), + * to get endpoint interrupt on every DMA req, but that didn't seem + * to work reliably. + * + * REVISIT an updated g_file_storage can set req->short_not_ok, which + * then becomes usable as a runtime "use mode 1" hint... + */ + + csr |= MUSB_RXCSR_DMAENAB; +#ifdef USE_MODE1 + csr |= MUSB_RXCSR_AUTOCLEAR; + /* csr |= MUSB_RXCSR_DMAMODE; */ + + /* this special sequence (enabling and then + * disabling MUSB_RXCSR_DMAMODE) is required + * to get DMAReq to activate + */ + musb_writew(epio, MUSB_RXCSR, + csr | MUSB_RXCSR_DMAMODE); +#endif + musb_writew(epio, MUSB_RXCSR, csr); + + if (request->actual < request->length) { + int transfer_size = 0; +#ifdef USE_MODE1 + transfer_size = min(request->length, + channel->max_len); +#else + transfer_size = len; +#endif + if (transfer_size <= musb_ep->packet_sz) + musb_ep->dma->desired_mode = 0; + else + musb_ep->dma->desired_mode = 1; + + use_dma = c->channel_program( + channel, + musb_ep->packet_sz, + channel->desired_mode, + request->dma + + request->actual, + transfer_size); + } + + if (use_dma) + return; + } +#endif /* Mentor's DMA */ + + fifo_count = request->length - request->actual; + DBG(3, "%s OUT/RX pio fifo %d/%d, maxpacket %d\n", + musb_ep->end_point.name, + len, fifo_count, + musb_ep->packet_sz); + + fifo_count = min(len, fifo_count); + +#ifdef CONFIG_USB_TUSB_OMAP_DMA + if (tusb_dma_omap() && musb_ep->dma) { + struct dma_controller *c = musb->dma_controller; + struct dma_channel *channel = musb_ep->dma; + u32 dma_addr = request->dma + request->actual; + int ret; + + ret = c->channel_program(channel, + musb_ep->packet_sz, + channel->desired_mode, + dma_addr, + fifo_count); + if (ret) + return; + } +#endif + + musb_read_fifo(musb_ep->hw_ep, fifo_count, (u8 *) + (request->buf + request->actual)); + request->actual += fifo_count; + + /* REVISIT if we left anything in the fifo, flush + * it and report -EOVERFLOW + */ + + /* ack the read! */ + csr |= MUSB_RXCSR_P_WZC_BITS; + csr &= ~MUSB_RXCSR_RXPKTRDY; + musb_writew(epio, MUSB_RXCSR, csr); + } + } + + /* reach the end or short packet detected */ + if (request->actual == request->length || len < musb_ep->packet_sz) + musb_g_giveback(musb_ep, request, 0); +} + +/* + * Data ready for a request; called from IRQ + */ +void musb_g_rx(struct musb *musb, u8 epnum) +{ + u16 csr; + struct usb_request *request; + void __iomem *mbase = musb->mregs; + struct musb_ep *musb_ep = &musb->endpoints[epnum].ep_out; + void __iomem *epio = musb->endpoints[epnum].regs; + struct dma_channel *dma; + + musb_ep_select(mbase, epnum); + + request = next_request(musb_ep); + + csr = musb_readw(epio, MUSB_RXCSR); + dma = is_dma_capable() ? musb_ep->dma : NULL; + + DBG(4, "<== %s, rxcsr %04x%s %p\n", musb_ep->end_point.name, + csr, dma ? " (dma)" : "", request); + + if (csr & MUSB_RXCSR_P_SENTSTALL) { + if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) { + dma->status = MUSB_DMA_STATUS_CORE_ABORT; + (void) musb->dma_controller->channel_abort(dma); + request->actual += musb_ep->dma->actual_len; + } + + csr |= MUSB_RXCSR_P_WZC_BITS; + csr &= ~MUSB_RXCSR_P_SENTSTALL; + musb_writew(epio, MUSB_RXCSR, csr); + + if (request) + musb_g_giveback(musb_ep, request, -EPIPE); + goto done; + } + + if (csr & MUSB_RXCSR_P_OVERRUN) { + /* csr |= MUSB_RXCSR_P_WZC_BITS; */ + csr &= ~MUSB_RXCSR_P_OVERRUN; + musb_writew(epio, MUSB_RXCSR, csr); + + DBG(3, "%s iso overrun on %p\n", musb_ep->name, request); + if (request && request->status == -EINPROGRESS) + request->status = -EOVERFLOW; + } + if (csr & MUSB_RXCSR_INCOMPRX) { + /* REVISIT not necessarily an error */ + DBG(4, "%s, incomprx\n", musb_ep->end_point.name); + } + + if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) { + /* "should not happen"; likely RXPKTRDY pending for DMA */ + DBG((csr & MUSB_RXCSR_DMAENAB) ? 4 : 1, + "%s busy, csr %04x\n", + musb_ep->end_point.name, csr); + goto done; + } + + if (dma && (csr & MUSB_RXCSR_DMAENAB)) { + csr &= ~(MUSB_RXCSR_AUTOCLEAR + | MUSB_RXCSR_DMAENAB + | MUSB_RXCSR_DMAMODE); + musb_writew(epio, MUSB_RXCSR, + MUSB_RXCSR_P_WZC_BITS | csr); + + request->actual += musb_ep->dma->actual_len; + + DBG(4, "RXCSR%d %04x, dma off, %04x, len %zu, req %p\n", + epnum, csr, + musb_readw(epio, MUSB_RXCSR), + musb_ep->dma->actual_len, request); + +#if defined(CONFIG_USB_INVENTRA_DMA) || defined(CONFIG_USB_TUSB_OMAP_DMA) + /* Autoclear doesn't clear RxPktRdy for short packets */ + if ((dma->desired_mode == 0) + || (dma->actual_len + & (musb_ep->packet_sz - 1))) { + /* ack the read! */ + csr &= ~MUSB_RXCSR_RXPKTRDY; + musb_writew(epio, MUSB_RXCSR, csr); + } + + /* incomplete, and not short? wait for next IN packet */ + if ((request->actual < request->length) + && (musb_ep->dma->actual_len + == musb_ep->packet_sz)) + goto done; +#endif + musb_g_giveback(musb_ep, request, 0); + + request = next_request(musb_ep); + if (!request) + goto done; + + /* don't start more i/o till the stall clears */ + musb_ep_select(mbase, epnum); + csr = musb_readw(epio, MUSB_RXCSR); + if (csr & MUSB_RXCSR_P_SENDSTALL) + goto done; + } + + + /* analyze request if the ep is hot */ + if (request) + rxstate(musb, to_musb_request(request)); + else + DBG(3, "packet waiting for %s%s request\n", + musb_ep->desc ? "" : "inactive ", + musb_ep->end_point.name); + +done: + return; +} + +/* ------------------------------------------------------------ */ + +static int musb_gadget_enable(struct usb_ep *ep, + const struct usb_endpoint_descriptor *desc) +{ + unsigned long flags; + struct musb_ep *musb_ep; + struct musb_hw_ep *hw_ep; + void __iomem *regs; + struct musb *musb; + void __iomem *mbase; + u8 epnum; + u16 csr; + unsigned tmp; + int status = -EINVAL; + + if (!ep || !desc) + return -EINVAL; + + musb_ep = to_musb_ep(ep); + hw_ep = musb_ep->hw_ep; + regs = hw_ep->regs; + musb = musb_ep->musb; + mbase = musb->mregs; + epnum = musb_ep->current_epnum; + + spin_lock_irqsave(&musb->lock, flags); + + if (musb_ep->desc) { + status = -EBUSY; + goto fail; + } + musb_ep->type = desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK; + + /* check direction and (later) maxpacket size against endpoint */ + if ((desc->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK) != epnum) + goto fail; + + /* REVISIT this rules out high bandwidth periodic transfers */ + tmp = le16_to_cpu(desc->wMaxPacketSize); + if (tmp & ~0x07ff) + goto fail; + musb_ep->packet_sz = tmp; + + /* enable the interrupts for the endpoint, set the endpoint + * packet size (or fail), set the mode, clear the fifo + */ + musb_ep_select(mbase, epnum); + if (desc->bEndpointAddress & USB_DIR_IN) { + u16 int_txe = musb_readw(mbase, MUSB_INTRTXE); + + if (hw_ep->is_shared_fifo) + musb_ep->is_in = 1; + if (!musb_ep->is_in) + goto fail; + if (tmp > hw_ep->max_packet_sz_tx) + goto fail; + + int_txe |= (1 << epnum); + musb_writew(mbase, MUSB_INTRTXE, int_txe); + + /* REVISIT if can_bulk_split(), use by updating "tmp"; + * likewise high bandwidth periodic tx + */ + musb_writew(regs, MUSB_TXMAXP, tmp); + + csr = MUSB_TXCSR_MODE | MUSB_TXCSR_CLRDATATOG; + if (musb_readw(regs, MUSB_TXCSR) + & MUSB_TXCSR_FIFONOTEMPTY) + csr |= MUSB_TXCSR_FLUSHFIFO; + if (musb_ep->type == USB_ENDPOINT_XFER_ISOC) + csr |= MUSB_TXCSR_P_ISO; + + /* set twice in case of double buffering */ + musb_writew(regs, MUSB_TXCSR, csr); + /* REVISIT may be inappropriate w/o FIFONOTEMPTY ... */ + musb_writew(regs, MUSB_TXCSR, csr); + + } else { + u16 int_rxe = musb_readw(mbase, MUSB_INTRRXE); + + if (hw_ep->is_shared_fifo) + musb_ep->is_in = 0; + if (musb_ep->is_in) + goto fail; + if (tmp > hw_ep->max_packet_sz_rx) + goto fail; + + int_rxe |= (1 << epnum); + musb_writew(mbase, MUSB_INTRRXE, int_rxe); + + /* REVISIT if can_bulk_combine() use by updating "tmp" + * likewise high bandwidth periodic rx + */ + musb_writew(regs, MUSB_RXMAXP, tmp); + + /* force shared fifo to OUT-only mode */ + if (hw_ep->is_shared_fifo) { + csr = musb_readw(regs, MUSB_TXCSR); + csr &= ~(MUSB_TXCSR_MODE | MUSB_TXCSR_TXPKTRDY); + musb_writew(regs, MUSB_TXCSR, csr); + } + + csr = MUSB_RXCSR_FLUSHFIFO | MUSB_RXCSR_CLRDATATOG; + if (musb_ep->type == USB_ENDPOINT_XFER_ISOC) + csr |= MUSB_RXCSR_P_ISO; + else if (musb_ep->type == USB_ENDPOINT_XFER_INT) + csr |= MUSB_RXCSR_DISNYET; + + /* set twice in case of double buffering */ + musb_writew(regs, MUSB_RXCSR, csr); + musb_writew(regs, MUSB_RXCSR, csr); + } + + /* NOTE: all the I/O code _should_ work fine without DMA, in case + * for some reason you run out of channels here. + */ + if (is_dma_capable() && musb->dma_controller) { + struct dma_controller *c = musb->dma_controller; + + musb_ep->dma = c->channel_alloc(c, hw_ep, + (desc->bEndpointAddress & USB_DIR_IN)); + } else + musb_ep->dma = NULL; + + musb_ep->desc = desc; + musb_ep->busy = 0; + status = 0; + + pr_debug("%s periph: enabled %s for %s %s, %smaxpacket %d\n", + musb_driver_name, musb_ep->end_point.name, + ({ char *s; switch (musb_ep->type) { + case USB_ENDPOINT_XFER_BULK: s = "bulk"; break; + case USB_ENDPOINT_XFER_INT: s = "int"; break; + default: s = "iso"; break; + }; s; }), + musb_ep->is_in ? "IN" : "OUT", + musb_ep->dma ? "dma, " : "", + musb_ep->packet_sz); + + schedule_work(&musb->irq_work); + +fail: + spin_unlock_irqrestore(&musb->lock, flags); + return status; +} + +/* + * Disable an endpoint flushing all requests queued. + */ +static int musb_gadget_disable(struct usb_ep *ep) +{ + unsigned long flags; + struct musb *musb; + u8 epnum; + struct musb_ep *musb_ep; + void __iomem *epio; + int status = 0; + + musb_ep = to_musb_ep(ep); + musb = musb_ep->musb; + epnum = musb_ep->current_epnum; + epio = musb->endpoints[epnum].regs; + + spin_lock_irqsave(&musb->lock, flags); + musb_ep_select(musb->mregs, epnum); + + /* zero the endpoint sizes */ + if (musb_ep->is_in) { + u16 int_txe = musb_readw(musb->mregs, MUSB_INTRTXE); + int_txe &= ~(1 << epnum); + musb_writew(musb->mregs, MUSB_INTRTXE, int_txe); + musb_writew(epio, MUSB_TXMAXP, 0); + } else { + u16 int_rxe = musb_readw(musb->mregs, MUSB_INTRRXE); + int_rxe &= ~(1 << epnum); + musb_writew(musb->mregs, MUSB_INTRRXE, int_rxe); + musb_writew(epio, MUSB_RXMAXP, 0); + } + + musb_ep->desc = NULL; + + /* abort all pending DMA and requests */ + nuke(musb_ep, -ESHUTDOWN); + + schedule_work(&musb->irq_work); + + spin_unlock_irqrestore(&(musb->lock), flags); + + DBG(2, "%s\n", musb_ep->end_point.name); + + return status; +} + +/* + * Allocate a request for an endpoint. + * Reused by ep0 code. + */ +struct usb_request *musb_alloc_request(struct usb_ep *ep, gfp_t gfp_flags) +{ + struct musb_ep *musb_ep = to_musb_ep(ep); + struct musb_request *request = NULL; + + request = kzalloc(sizeof *request, gfp_flags); + if (request) { + INIT_LIST_HEAD(&request->request.list); + request->request.dma = DMA_ADDR_INVALID; + request->epnum = musb_ep->current_epnum; + request->ep = musb_ep; + } + + return &request->request; +} + +/* + * Free a request + * Reused by ep0 code. + */ +void musb_free_request(struct usb_ep *ep, struct usb_request *req) +{ + kfree(to_musb_request(req)); +} + +static LIST_HEAD(buffers); + +struct free_record { + struct list_head list; + struct device *dev; + unsigned bytes; + dma_addr_t dma; +}; + +/* + * Context: controller locked, IRQs blocked. + */ +static void musb_ep_restart(struct musb *musb, struct musb_request *req) +{ + DBG(3, "<== %s request %p len %u on hw_ep%d\n", + req->tx ? "TX/IN" : "RX/OUT", + &req->request, req->request.length, req->epnum); + + musb_ep_select(musb->mregs, req->epnum); + if (req->tx) + txstate(musb, req); + else + rxstate(musb, req); +} + +static int musb_gadget_queue(struct usb_ep *ep, struct usb_request *req, + gfp_t gfp_flags) +{ + struct musb_ep *musb_ep; + struct musb_request *request; + struct musb *musb; + int status = 0; + unsigned long lockflags; + + if (!ep || !req) + return -EINVAL; + if (!req->buf) + return -ENODATA; + + musb_ep = to_musb_ep(ep); + musb = musb_ep->musb; + + request = to_musb_request(req); + request->musb = musb; + + if (request->ep != musb_ep) + return -EINVAL; + + DBG(4, "<== to %s request=%p\n", ep->name, req); + + /* request is mine now... */ + request->request.actual = 0; + request->request.status = -EINPROGRESS; + request->epnum = musb_ep->current_epnum; + request->tx = musb_ep->is_in; + + if (is_dma_capable() && musb_ep->dma) { + if (request->request.dma == DMA_ADDR_INVALID) { + request->request.dma = dma_map_single( + musb->controller, + request->request.buf, + request->request.length, + request->tx + ? DMA_TO_DEVICE + : DMA_FROM_DEVICE); + request->mapped = 1; + } else { + dma_sync_single_for_device(musb->controller, + request->request.dma, + request->request.length, + request->tx + ? DMA_TO_DEVICE + : DMA_FROM_DEVICE); + request->mapped = 0; + } + } else if (!req->buf) { + return -ENODATA; + } else + request->mapped = 0; + + spin_lock_irqsave(&musb->lock, lockflags); + + /* don't queue if the ep is down */ + if (!musb_ep->desc) { + DBG(4, "req %p queued to %s while ep %s\n", + req, ep->name, "disabled"); + status = -ESHUTDOWN; + goto cleanup; + } + + /* add request to the list */ + list_add_tail(&(request->request.list), &(musb_ep->req_list)); + + /* it this is the head of the queue, start i/o ... */ + if (!musb_ep->busy && &request->request.list == musb_ep->req_list.next) + musb_ep_restart(musb, request); + +cleanup: + spin_unlock_irqrestore(&musb->lock, lockflags); + return status; +} + +static int musb_gadget_dequeue(struct usb_ep *ep, struct usb_request *request) +{ + struct musb_ep *musb_ep = to_musb_ep(ep); + struct usb_request *r; + unsigned long flags; + int status = 0; + struct musb *musb = musb_ep->musb; + + if (!ep || !request || to_musb_request(request)->ep != musb_ep) + return -EINVAL; + + spin_lock_irqsave(&musb->lock, flags); + + list_for_each_entry(r, &musb_ep->req_list, list) { + if (r == request) + break; + } + if (r != request) { + DBG(3, "request %p not queued to %s\n", request, ep->name); + status = -EINVAL; + goto done; + } + + /* if the hardware doesn't have the request, easy ... */ + if (musb_ep->req_list.next != &request->list || musb_ep->busy) + musb_g_giveback(musb_ep, request, -ECONNRESET); + + /* ... else abort the dma transfer ... */ + else if (is_dma_capable() && musb_ep->dma) { + struct dma_controller *c = musb->dma_controller; + + musb_ep_select(musb->mregs, musb_ep->current_epnum); + if (c->channel_abort) + status = c->channel_abort(musb_ep->dma); + else + status = -EBUSY; + if (status == 0) + musb_g_giveback(musb_ep, request, -ECONNRESET); + } else { + /* NOTE: by sticking to easily tested hardware/driver states, + * we leave counting of in-flight packets imprecise. + */ + musb_g_giveback(musb_ep, request, -ECONNRESET); + } + +done: + spin_unlock_irqrestore(&musb->lock, flags); + return status; +} + +/* + * Set or clear the halt bit of an endpoint. A halted enpoint won't tx/rx any + * data but will queue requests. + * + * exported to ep0 code + */ +int musb_gadget_set_halt(struct usb_ep *ep, int value) +{ + struct musb_ep *musb_ep = to_musb_ep(ep); + u8 epnum = musb_ep->current_epnum; + struct musb *musb = musb_ep->musb; + void __iomem *epio = musb->endpoints[epnum].regs; + void __iomem *mbase; + unsigned long flags; + u16 csr; + struct musb_request *request = NULL; + int status = 0; + + if (!ep) + return -EINVAL; + mbase = musb->mregs; + + spin_lock_irqsave(&musb->lock, flags); + + if ((USB_ENDPOINT_XFER_ISOC == musb_ep->type)) { + status = -EINVAL; + goto done; + } + + musb_ep_select(mbase, epnum); + + /* cannot portably stall with non-empty FIFO */ + request = to_musb_request(next_request(musb_ep)); + if (value && musb_ep->is_in) { + csr = musb_readw(epio, MUSB_TXCSR); + if (csr & MUSB_TXCSR_FIFONOTEMPTY) { + DBG(3, "%s fifo busy, cannot halt\n", ep->name); + spin_unlock_irqrestore(&musb->lock, flags); + return -EAGAIN; + } + + } + + /* set/clear the stall and toggle bits */ + DBG(2, "%s: %s stall\n", ep->name, value ? "set" : "clear"); + if (musb_ep->is_in) { + csr = musb_readw(epio, MUSB_TXCSR); + if (csr & MUSB_TXCSR_FIFONOTEMPTY) + csr |= MUSB_TXCSR_FLUSHFIFO; + csr |= MUSB_TXCSR_P_WZC_BITS + | MUSB_TXCSR_CLRDATATOG; + if (value) + csr |= MUSB_TXCSR_P_SENDSTALL; + else + csr &= ~(MUSB_TXCSR_P_SENDSTALL + | MUSB_TXCSR_P_SENTSTALL); + csr &= ~MUSB_TXCSR_TXPKTRDY; + musb_writew(epio, MUSB_TXCSR, csr); + } else { + csr = musb_readw(epio, MUSB_RXCSR); + csr |= MUSB_RXCSR_P_WZC_BITS + | MUSB_RXCSR_FLUSHFIFO + | MUSB_RXCSR_CLRDATATOG; + if (value) + csr |= MUSB_RXCSR_P_SENDSTALL; + else + csr &= ~(MUSB_RXCSR_P_SENDSTALL + | MUSB_RXCSR_P_SENTSTALL); + musb_writew(epio, MUSB_RXCSR, csr); + } + +done: + + /* maybe start the first request in the queue */ + if (!musb_ep->busy && !value && request) { + DBG(3, "restarting the request\n"); + musb_ep_restart(musb, request); + } + + spin_unlock_irqrestore(&musb->lock, flags); + return status; +} + +static int musb_gadget_fifo_status(struct usb_ep *ep) +{ + struct musb_ep *musb_ep = to_musb_ep(ep); + void __iomem *epio = musb_ep->hw_ep->regs; + int retval = -EINVAL; + + if (musb_ep->desc && !musb_ep->is_in) { + struct musb *musb = musb_ep->musb; + int epnum = musb_ep->current_epnum; + void __iomem *mbase = musb->mregs; + unsigned long flags; + + spin_lock_irqsave(&musb->lock, flags); + + musb_ep_select(mbase, epnum); + /* FIXME return zero unless RXPKTRDY is set */ + retval = musb_readw(epio, MUSB_RXCOUNT); + + spin_unlock_irqrestore(&musb->lock, flags); + } + return retval; +} + +static void musb_gadget_fifo_flush(struct usb_ep *ep) +{ + struct musb_ep *musb_ep = to_musb_ep(ep); + struct musb *musb = musb_ep->musb; + u8 epnum = musb_ep->current_epnum; + void __iomem *epio = musb->endpoints[epnum].regs; + void __iomem *mbase; + unsigned long flags; + u16 csr, int_txe; + + mbase = musb->mregs; + + spin_lock_irqsave(&musb->lock, flags); + musb_ep_select(mbase, (u8) epnum); + + /* disable interrupts */ + int_txe = musb_readw(mbase, MUSB_INTRTXE); + musb_writew(mbase, MUSB_INTRTXE, int_txe & ~(1 << epnum)); + + if (musb_ep->is_in) { + csr = musb_readw(epio, MUSB_TXCSR); + if (csr & MUSB_TXCSR_FIFONOTEMPTY) { + csr |= MUSB_TXCSR_FLUSHFIFO | MUSB_TXCSR_P_WZC_BITS; + musb_writew(epio, MUSB_TXCSR, csr); + /* REVISIT may be inappropriate w/o FIFONOTEMPTY ... */ + musb_writew(epio, MUSB_TXCSR, csr); + } + } else { + csr = musb_readw(epio, MUSB_RXCSR); + csr |= MUSB_RXCSR_FLUSHFIFO | MUSB_RXCSR_P_WZC_BITS; + musb_writew(epio, MUSB_RXCSR, csr); + musb_writew(epio, MUSB_RXCSR, csr); + } + + /* re-enable interrupt */ + musb_writew(mbase, MUSB_INTRTXE, int_txe); + spin_unlock_irqrestore(&musb->lock, flags); +} + +static const struct usb_ep_ops musb_ep_ops = { + .enable = musb_gadget_enable, + .disable = musb_gadget_disable, + .alloc_request = musb_alloc_request, + .free_request = musb_free_request, + .queue = musb_gadget_queue, + .dequeue = musb_gadget_dequeue, + .set_halt = musb_gadget_set_halt, + .fifo_status = musb_gadget_fifo_status, + .fifo_flush = musb_gadget_fifo_flush +}; + +/* ----------------------------------------------------------------------- */ + +static int musb_gadget_get_frame(struct usb_gadget *gadget) +{ + struct musb *musb = gadget_to_musb(gadget); + + return (int)musb_readw(musb->mregs, MUSB_FRAME); +} + +static int musb_gadget_wakeup(struct usb_gadget *gadget) +{ + struct musb *musb = gadget_to_musb(gadget); + void __iomem *mregs = musb->mregs; + unsigned long flags; + int status = -EINVAL; + u8 power, devctl; + int retries; + + spin_lock_irqsave(&musb->lock, flags); + + switch (musb->xceiv.state) { + case OTG_STATE_B_PERIPHERAL: + /* NOTE: OTG state machine doesn't include B_SUSPENDED; + * that's part of the standard usb 1.1 state machine, and + * doesn't affect OTG transitions. + */ + if (musb->may_wakeup && musb->is_suspended) + break; + goto done; + case OTG_STATE_B_IDLE: + /* Start SRP ... OTG not required. */ + devctl = musb_readb(mregs, MUSB_DEVCTL); + DBG(2, "Sending SRP: devctl: %02x\n", devctl); + devctl |= MUSB_DEVCTL_SESSION; + musb_writeb(mregs, MUSB_DEVCTL, devctl); + devctl = musb_readb(mregs, MUSB_DEVCTL); + retries = 100; + while (!(devctl & MUSB_DEVCTL_SESSION)) { + devctl = musb_readb(mregs, MUSB_DEVCTL); + if (retries-- < 1) + break; + } + retries = 10000; + while (devctl & MUSB_DEVCTL_SESSION) { + devctl = musb_readb(mregs, MUSB_DEVCTL); + if (retries-- < 1) + break; + } + + /* Block idling for at least 1s */ + musb_platform_try_idle(musb, + jiffies + msecs_to_jiffies(1 * HZ)); + + status = 0; + goto done; + default: + DBG(2, "Unhandled wake: %s\n", otg_state_string(musb)); + goto done; + } + + status = 0; + + power = musb_readb(mregs, MUSB_POWER); + power |= MUSB_POWER_RESUME; + musb_writeb(mregs, MUSB_POWER, power); + DBG(2, "issue wakeup\n"); + + /* FIXME do this next chunk in a timer callback, no udelay */ + mdelay(2); + + power = musb_readb(mregs, MUSB_POWER); + power &= ~MUSB_POWER_RESUME; + musb_writeb(mregs, MUSB_POWER, power); +done: + spin_unlock_irqrestore(&musb->lock, flags); + return status; +} + +static int +musb_gadget_set_self_powered(struct usb_gadget *gadget, int is_selfpowered) +{ + struct musb *musb = gadget_to_musb(gadget); + + musb->is_self_powered = !!is_selfpowered; + return 0; +} + +static void musb_pullup(struct musb *musb, int is_on) +{ + u8 power; + + power = musb_readb(musb->mregs, MUSB_POWER); + if (is_on) + power |= MUSB_POWER_SOFTCONN; + else + power &= ~MUSB_POWER_SOFTCONN; + + /* FIXME if on, HdrcStart; if off, HdrcStop */ + + DBG(3, "gadget %s D+ pullup %s\n", + musb->gadget_driver->function, is_on ? "on" : "off"); + musb_writeb(musb->mregs, MUSB_POWER, power); +} + +#if 0 +static int musb_gadget_vbus_session(struct usb_gadget *gadget, int is_active) +{ + DBG(2, "<= %s =>\n", __func__); + + /* + * FIXME iff driver's softconnect flag is set (as it is during probe, + * though that can clear it), just musb_pullup(). + */ + + return -EINVAL; +} +#endif + +static int musb_gadget_vbus_draw(struct usb_gadget *gadget, unsigned mA) +{ + struct musb *musb = gadget_to_musb(gadget); + + if (!musb->xceiv.set_power) + return -EOPNOTSUPP; + return otg_set_power(&musb->xceiv, mA); +} + +static int musb_gadget_pullup(struct usb_gadget *gadget, int is_on) +{ + struct musb *musb = gadget_to_musb(gadget); + unsigned long flags; + + is_on = !!is_on; + + /* NOTE: this assumes we are sensing vbus; we'd rather + * not pullup unless the B-session is active. + */ + spin_lock_irqsave(&musb->lock, flags); + if (is_on != musb->softconnect) { + musb->softconnect = is_on; + musb_pullup(musb, is_on); + } + spin_unlock_irqrestore(&musb->lock, flags); + return 0; +} + +static const struct usb_gadget_ops musb_gadget_operations = { + .get_frame = musb_gadget_get_frame, + .wakeup = musb_gadget_wakeup, + .set_selfpowered = musb_gadget_set_self_powered, + /* .vbus_session = musb_gadget_vbus_session, */ + .vbus_draw = musb_gadget_vbus_draw, + .pullup = musb_gadget_pullup, +}; + +/* ----------------------------------------------------------------------- */ + +/* Registration */ + +/* Only this registration code "knows" the rule (from USB standards) + * about there being only one external upstream port. It assumes + * all peripheral ports are external... + */ +static struct musb *the_gadget; + +static void musb_gadget_release(struct device *dev) +{ + /* kref_put(WHAT) */ + dev_dbg(dev, "%s\n", __func__); +} + + +static void __init +init_peripheral_ep(struct musb *musb, struct musb_ep *ep, u8 epnum, int is_in) +{ + struct musb_hw_ep *hw_ep = musb->endpoints + epnum; + + memset(ep, 0, sizeof *ep); + + ep->current_epnum = epnum; + ep->musb = musb; + ep->hw_ep = hw_ep; + ep->is_in = is_in; + + INIT_LIST_HEAD(&ep->req_list); + + sprintf(ep->name, "ep%d%s", epnum, + (!epnum || hw_ep->is_shared_fifo) ? "" : ( + is_in ? "in" : "out")); + ep->end_point.name = ep->name; + INIT_LIST_HEAD(&ep->end_point.ep_list); + if (!epnum) { + ep->end_point.maxpacket = 64; + ep->end_point.ops = &musb_g_ep0_ops; + musb->g.ep0 = &ep->end_point; + } else { + if (is_in) + ep->end_point.maxpacket = hw_ep->max_packet_sz_tx; + else + ep->end_point.maxpacket = hw_ep->max_packet_sz_rx; + ep->end_point.ops = &musb_ep_ops; + list_add_tail(&ep->end_point.ep_list, &musb->g.ep_list); + } +} + +/* + * Initialize the endpoints exposed to peripheral drivers, with backlinks + * to the rest of the driver state. + */ +static inline void __init musb_g_init_endpoints(struct musb *musb) +{ + u8 epnum; + struct musb_hw_ep *hw_ep; + unsigned count = 0; + + /* intialize endpoint list just once */ + INIT_LIST_HEAD(&(musb->g.ep_list)); + + for (epnum = 0, hw_ep = musb->endpoints; + epnum < musb->nr_endpoints; + epnum++, hw_ep++) { + if (hw_ep->is_shared_fifo /* || !epnum */) { + init_peripheral_ep(musb, &hw_ep->ep_in, epnum, 0); + count++; + } else { + if (hw_ep->max_packet_sz_tx) { + init_peripheral_ep(musb, &hw_ep->ep_in, + epnum, 1); + count++; + } + if (hw_ep->max_packet_sz_rx) { + init_peripheral_ep(musb, &hw_ep->ep_out, + epnum, 0); + count++; + } + } + } +} + +/* called once during driver setup to initialize and link into + * the driver model; memory is zeroed. + */ +int __init musb_gadget_setup(struct musb *musb) +{ + int status; + + /* REVISIT minor race: if (erroneously) setting up two + * musb peripherals at the same time, only the bus lock + * is probably held. + */ + if (the_gadget) + return -EBUSY; + the_gadget = musb; + + musb->g.ops = &musb_gadget_operations; + musb->g.is_dualspeed = 1; + musb->g.speed = USB_SPEED_UNKNOWN; + + /* this "gadget" abstracts/virtualizes the controller */ + strcpy(musb->g.dev.bus_id, "gadget"); + musb->g.dev.parent = musb->controller; + musb->g.dev.dma_mask = musb->controller->dma_mask; + musb->g.dev.release = musb_gadget_release; + musb->g.name = musb_driver_name; + + if (is_otg_enabled(musb)) + musb->g.is_otg = 1; + + musb_g_init_endpoints(musb); + + musb->is_active = 0; + musb_platform_try_idle(musb, 0); + + status = device_register(&musb->g.dev); + if (status != 0) + the_gadget = NULL; + return status; +} + +void musb_gadget_cleanup(struct musb *musb) +{ + if (musb != the_gadget) + return; + + device_unregister(&musb->g.dev); + the_gadget = NULL; +} + +/* + * Register the gadget driver. Used by gadget drivers when + * registering themselves with the controller. + * + * -EINVAL something went wrong (not driver) + * -EBUSY another gadget is already using the controller + * -ENOMEM no memeory to perform the operation + * + * @param driver the gadget driver + * @return <0 if error, 0 if everything is fine + */ +int usb_gadget_register_driver(struct usb_gadget_driver *driver) +{ + int retval; + unsigned long flags; + struct musb *musb = the_gadget; + + if (!driver + || driver->speed != USB_SPEED_HIGH + || !driver->bind + || !driver->setup) + return -EINVAL; + + /* driver must be initialized to support peripheral mode */ + if (!musb || !(musb->board_mode == MUSB_OTG + || musb->board_mode != MUSB_OTG)) { + DBG(1, "%s, no dev??\n", __func__); + return -ENODEV; + } + + DBG(3, "registering driver %s\n", driver->function); + spin_lock_irqsave(&musb->lock, flags); + + if (musb->gadget_driver) { + DBG(1, "%s is already bound to %s\n", + musb_driver_name, + musb->gadget_driver->driver.name); + retval = -EBUSY; + } else { + musb->gadget_driver = driver; + musb->g.dev.driver = &driver->driver; + driver->driver.bus = NULL; + musb->softconnect = 1; + retval = 0; + } + + spin_unlock_irqrestore(&musb->lock, flags); + + if (retval == 0) + retval = driver->bind(&musb->g); + if (retval != 0) { + DBG(3, "bind to driver %s failed --> %d\n", + driver->driver.name, retval); + musb->gadget_driver = NULL; + musb->g.dev.driver = NULL; + } + + /* start peripheral and/or OTG engines */ + if (retval == 0) { + spin_lock_irqsave(&musb->lock, flags); + + /* REVISIT always use otg_set_peripheral(), handling + * issues including the root hub one below ... + */ + musb->xceiv.gadget = &musb->g; + musb->xceiv.state = OTG_STATE_B_IDLE; + musb->is_active = 1; + + /* FIXME this ignores the softconnect flag. Drivers are + * allowed hold the peripheral inactive until for example + * userspace hooks up printer hardware or DSP codecs, so + * hosts only see fully functional devices. + */ + + if (!is_otg_enabled(musb)) + musb_start(musb); + + spin_unlock_irqrestore(&musb->lock, flags); + + if (is_otg_enabled(musb)) { + DBG(3, "OTG startup...\n"); + + /* REVISIT: funcall to other code, which also + * handles power budgeting ... this way also + * ensures HdrcStart is indirectly called. + */ + retval = usb_add_hcd(musb_to_hcd(musb), -1, 0); + if (retval < 0) { + DBG(1, "add_hcd failed, %d\n", retval); + spin_lock_irqsave(&musb->lock, flags); + musb->xceiv.gadget = NULL; + musb->xceiv.state = OTG_STATE_UNDEFINED; + musb->gadget_driver = NULL; + musb->g.dev.driver = NULL; + spin_unlock_irqrestore(&musb->lock, flags); + } + } + } + + return retval; +} +EXPORT_SYMBOL(usb_gadget_register_driver); + +static void stop_activity(struct musb *musb, struct usb_gadget_driver *driver) +{ + int i; + struct musb_hw_ep *hw_ep; + + /* don't disconnect if it's not connected */ + if (musb->g.speed == USB_SPEED_UNKNOWN) + driver = NULL; + else + musb->g.speed = USB_SPEED_UNKNOWN; + + /* deactivate the hardware */ + if (musb->softconnect) { + musb->softconnect = 0; + musb_pullup(musb, 0); + } + musb_stop(musb); + + /* killing any outstanding requests will quiesce the driver; + * then report disconnect + */ + if (driver) { + for (i = 0, hw_ep = musb->endpoints; + i < musb->nr_endpoints; + i++, hw_ep++) { + musb_ep_select(musb->mregs, i); + if (hw_ep->is_shared_fifo /* || !epnum */) { + nuke(&hw_ep->ep_in, -ESHUTDOWN); + } else { + if (hw_ep->max_packet_sz_tx) + nuke(&hw_ep->ep_in, -ESHUTDOWN); + if (hw_ep->max_packet_sz_rx) + nuke(&hw_ep->ep_out, -ESHUTDOWN); + } + } + + spin_unlock(&musb->lock); + driver->disconnect(&musb->g); + spin_lock(&musb->lock); + } +} + +/* + * Unregister the gadget driver. Used by gadget drivers when + * unregistering themselves from the controller. + * + * @param driver the gadget driver to unregister + */ +int usb_gadget_unregister_driver(struct usb_gadget_driver *driver) +{ + unsigned long flags; + int retval = 0; + struct musb *musb = the_gadget; + + if (!driver || !driver->unbind || !musb) + return -EINVAL; + + /* REVISIT always use otg_set_peripheral() here too; + * this needs to shut down the OTG engine. + */ + + spin_lock_irqsave(&musb->lock, flags); + +#ifdef CONFIG_USB_MUSB_OTG + musb_hnp_stop(musb); +#endif + + if (musb->gadget_driver == driver) { + + (void) musb_gadget_vbus_draw(&musb->g, 0); + + musb->xceiv.state = OTG_STATE_UNDEFINED; + stop_activity(musb, driver); + + DBG(3, "unregistering driver %s\n", driver->function); + spin_unlock_irqrestore(&musb->lock, flags); + driver->unbind(&musb->g); + spin_lock_irqsave(&musb->lock, flags); + + musb->gadget_driver = NULL; + musb->g.dev.driver = NULL; + + musb->is_active = 0; + musb_platform_try_idle(musb, 0); + } else + retval = -EINVAL; + spin_unlock_irqrestore(&musb->lock, flags); + + if (is_otg_enabled(musb) && retval == 0) { + usb_remove_hcd(musb_to_hcd(musb)); + /* FIXME we need to be able to register another + * gadget driver here and have everything work; + * that currently misbehaves. + */ + } + + return retval; +} +EXPORT_SYMBOL(usb_gadget_unregister_driver); + + +/* ----------------------------------------------------------------------- */ + +/* lifecycle operations called through plat_uds.c */ + +void musb_g_resume(struct musb *musb) +{ + musb->is_suspended = 0; + switch (musb->xceiv.state) { + case OTG_STATE_B_IDLE: + break; + case OTG_STATE_B_WAIT_ACON: + case OTG_STATE_B_PERIPHERAL: + musb->is_active = 1; + if (musb->gadget_driver && musb->gadget_driver->resume) { + spin_unlock(&musb->lock); + musb->gadget_driver->resume(&musb->g); + spin_lock(&musb->lock); + } + break; + default: + WARNING("unhandled RESUME transition (%s)\n", + otg_state_string(musb)); + } +} + +/* called when SOF packets stop for 3+ msec */ +void musb_g_suspend(struct musb *musb) +{ + u8 devctl; + + devctl = musb_readb(musb->mregs, MUSB_DEVCTL); + DBG(3, "devctl %02x\n", devctl); + + switch (musb->xceiv.state) { + case OTG_STATE_B_IDLE: + if ((devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS) + musb->xceiv.state = OTG_STATE_B_PERIPHERAL; + break; + case OTG_STATE_B_PERIPHERAL: + musb->is_suspended = 1; + if (musb->gadget_driver && musb->gadget_driver->suspend) { + spin_unlock(&musb->lock); + musb->gadget_driver->suspend(&musb->g); + spin_lock(&musb->lock); + } + break; + default: + /* REVISIT if B_HOST, clear DEVCTL.HOSTREQ; + * A_PERIPHERAL may need care too + */ + WARNING("unhandled SUSPEND transition (%s)\n", + otg_state_string(musb)); + } +} + +/* Called during SRP */ +void musb_g_wakeup(struct musb *musb) +{ + musb_gadget_wakeup(&musb->g); +} + +/* called when VBUS drops below session threshold, and in other cases */ +void musb_g_disconnect(struct musb *musb) +{ + void __iomem *mregs = musb->mregs; + u8 devctl = musb_readb(mregs, MUSB_DEVCTL); + + DBG(3, "devctl %02x\n", devctl); + + /* clear HR */ + musb_writeb(mregs, MUSB_DEVCTL, devctl & MUSB_DEVCTL_SESSION); + + /* don't draw vbus until new b-default session */ + (void) musb_gadget_vbus_draw(&musb->g, 0); + + musb->g.speed = USB_SPEED_UNKNOWN; + if (musb->gadget_driver && musb->gadget_driver->disconnect) { + spin_unlock(&musb->lock); + musb->gadget_driver->disconnect(&musb->g); + spin_lock(&musb->lock); + } + + switch (musb->xceiv.state) { + default: +#ifdef CONFIG_USB_MUSB_OTG + DBG(2, "Unhandled disconnect %s, setting a_idle\n", + otg_state_string(musb)); + musb->xceiv.state = OTG_STATE_A_IDLE; + break; + case OTG_STATE_A_PERIPHERAL: + musb->xceiv.state = OTG_STATE_A_WAIT_VFALL; + break; + case OTG_STATE_B_WAIT_ACON: + case OTG_STATE_B_HOST: +#endif + case OTG_STATE_B_PERIPHERAL: + case OTG_STATE_B_IDLE: + musb->xceiv.state = OTG_STATE_B_IDLE; + break; + case OTG_STATE_B_SRP_INIT: + break; + } + + musb->is_active = 0; +} + +void musb_g_reset(struct musb *musb) +__releases(musb->lock) +__acquires(musb->lock) +{ + void __iomem *mbase = musb->mregs; + u8 devctl = musb_readb(mbase, MUSB_DEVCTL); + u8 power; + + DBG(3, "<== %s addr=%x driver '%s'\n", + (devctl & MUSB_DEVCTL_BDEVICE) + ? "B-Device" : "A-Device", + musb_readb(mbase, MUSB_FADDR), + musb->gadget_driver + ? musb->gadget_driver->driver.name + : NULL + ); + + /* report disconnect, if we didn't already (flushing EP state) */ + if (musb->g.speed != USB_SPEED_UNKNOWN) + musb_g_disconnect(musb); + + /* clear HR */ + else if (devctl & MUSB_DEVCTL_HR) + musb_writeb(mbase, MUSB_DEVCTL, MUSB_DEVCTL_SESSION); + + + /* what speed did we negotiate? */ + power = musb_readb(mbase, MUSB_POWER); + musb->g.speed = (power & MUSB_POWER_HSMODE) + ? USB_SPEED_HIGH : USB_SPEED_FULL; + + /* start in USB_STATE_DEFAULT */ + musb->is_active = 1; + musb->is_suspended = 0; + MUSB_DEV_MODE(musb); + musb->address = 0; + musb->ep0_state = MUSB_EP0_STAGE_SETUP; + + musb->may_wakeup = 0; + musb->g.b_hnp_enable = 0; + musb->g.a_alt_hnp_support = 0; + musb->g.a_hnp_support = 0; + + /* Normal reset, as B-Device; + * or else after HNP, as A-Device + */ + if (devctl & MUSB_DEVCTL_BDEVICE) { + musb->xceiv.state = OTG_STATE_B_PERIPHERAL; + musb->g.is_a_peripheral = 0; + } else if (is_otg_enabled(musb)) { + musb->xceiv.state = OTG_STATE_A_PERIPHERAL; + musb->g.is_a_peripheral = 1; + } else + WARN_ON(1); + + /* start with default limits on VBUS power draw */ + (void) musb_gadget_vbus_draw(&musb->g, + is_otg_enabled(musb) ? 8 : 100); +} diff --git a/drivers/usb/musb/musb_gadget.h b/drivers/usb/musb/musb_gadget.h new file mode 100644 index 00000000000..59502da9f73 --- /dev/null +++ b/drivers/usb/musb/musb_gadget.h @@ -0,0 +1,108 @@ +/* + * MUSB OTG driver peripheral defines + * + * Copyright 2005 Mentor Graphics Corporation + * Copyright (C) 2005-2006 by Texas Instruments + * Copyright (C) 2006-2007 Nokia Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + */ + +#ifndef __MUSB_GADGET_H +#define __MUSB_GADGET_H + +struct musb_request { + struct usb_request request; + struct musb_ep *ep; + struct musb *musb; + u8 tx; /* endpoint direction */ + u8 epnum; + u8 mapped; +}; + +static inline struct musb_request *to_musb_request(struct usb_request *req) +{ + return req ? container_of(req, struct musb_request, request) : NULL; +} + +extern struct usb_request * +musb_alloc_request(struct usb_ep *ep, gfp_t gfp_flags); +extern void musb_free_request(struct usb_ep *ep, struct usb_request *req); + + +/* + * struct musb_ep - peripheral side view of endpoint rx or tx side + */ +struct musb_ep { + /* stuff towards the head is basically write-once. */ + struct usb_ep end_point; + char name[12]; + struct musb_hw_ep *hw_ep; + struct musb *musb; + u8 current_epnum; + + /* ... when enabled/disabled ... */ + u8 type; + u8 is_in; + u16 packet_sz; + const struct usb_endpoint_descriptor *desc; + struct dma_channel *dma; + + /* later things are modified based on usage */ + struct list_head req_list; + + /* true if lock must be dropped but req_list may not be advanced */ + u8 busy; +}; + +static inline struct musb_ep *to_musb_ep(struct usb_ep *ep) +{ + return ep ? container_of(ep, struct musb_ep, end_point) : NULL; +} + +static inline struct usb_request *next_request(struct musb_ep *ep) +{ + struct list_head *queue = &ep->req_list; + + if (list_empty(queue)) + return NULL; + return container_of(queue->next, struct usb_request, list); +} + +extern void musb_g_tx(struct musb *musb, u8 epnum); +extern void musb_g_rx(struct musb *musb, u8 epnum); + +extern const struct usb_ep_ops musb_g_ep0_ops; + +extern int musb_gadget_setup(struct musb *); +extern void musb_gadget_cleanup(struct musb *); + +extern void musb_g_giveback(struct musb_ep *, struct usb_request *, int); + +extern int musb_gadget_set_halt(struct usb_ep *ep, int value); + +#endif /* __MUSB_GADGET_H */ diff --git a/drivers/usb/musb/musb_gadget_ep0.c b/drivers/usb/musb/musb_gadget_ep0.c new file mode 100644 index 00000000000..48d7d3ccb24 --- /dev/null +++ b/drivers/usb/musb/musb_gadget_ep0.c @@ -0,0 +1,981 @@ +/* + * MUSB OTG peripheral driver ep0 handling + * + * Copyright 2005 Mentor Graphics Corporation + * Copyright (C) 2005-2006 by Texas Instruments + * Copyright (C) 2006-2007 Nokia Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + */ + +#include +#include +#include +#include +#include +#include +#include + +#include "musb_core.h" + +/* ep0 is always musb->endpoints[0].ep_in */ +#define next_ep0_request(musb) next_in_request(&(musb)->endpoints[0]) + +/* + * locking note: we use only the controller lock, for simpler correctness. + * It's always held with IRQs blocked. + * + * It protects the ep0 request queue as well as ep0_state, not just the + * controller and indexed registers. And that lock stays held unless it + * needs to be dropped to allow reentering this driver ... like upcalls to + * the gadget driver, or adjusting endpoint halt status. + */ + +static char *decode_ep0stage(u8 stage) +{ + switch (stage) { + case MUSB_EP0_STAGE_SETUP: return "idle"; + case MUSB_EP0_STAGE_TX: return "in"; + case MUSB_EP0_STAGE_RX: return "out"; + case MUSB_EP0_STAGE_ACKWAIT: return "wait"; + case MUSB_EP0_STAGE_STATUSIN: return "in/status"; + case MUSB_EP0_STAGE_STATUSOUT: return "out/status"; + default: return "?"; + } +} + +/* handle a standard GET_STATUS request + * Context: caller holds controller lock + */ +static int service_tx_status_request( + struct musb *musb, + const struct usb_ctrlrequest *ctrlrequest) +{ + void __iomem *mbase = musb->mregs; + int handled = 1; + u8 result[2], epnum = 0; + const u8 recip = ctrlrequest->bRequestType & USB_RECIP_MASK; + + result[1] = 0; + + switch (recip) { + case USB_RECIP_DEVICE: + result[0] = musb->is_self_powered << USB_DEVICE_SELF_POWERED; + result[0] |= musb->may_wakeup << USB_DEVICE_REMOTE_WAKEUP; +#ifdef CONFIG_USB_MUSB_OTG + if (musb->g.is_otg) { + result[0] |= musb->g.b_hnp_enable + << USB_DEVICE_B_HNP_ENABLE; + result[0] |= musb->g.a_alt_hnp_support + << USB_DEVICE_A_ALT_HNP_SUPPORT; + result[0] |= musb->g.a_hnp_support + << USB_DEVICE_A_HNP_SUPPORT; + } +#endif + break; + + case USB_RECIP_INTERFACE: + result[0] = 0; + break; + + case USB_RECIP_ENDPOINT: { + int is_in; + struct musb_ep *ep; + u16 tmp; + void __iomem *regs; + + epnum = (u8) ctrlrequest->wIndex; + if (!epnum) { + result[0] = 0; + break; + } + + is_in = epnum & USB_DIR_IN; + if (is_in) { + epnum &= 0x0f; + ep = &musb->endpoints[epnum].ep_in; + } else { + ep = &musb->endpoints[epnum].ep_out; + } + regs = musb->endpoints[epnum].regs; + + if (epnum >= MUSB_C_NUM_EPS || !ep->desc) { + handled = -EINVAL; + break; + } + + musb_ep_select(mbase, epnum); + if (is_in) + tmp = musb_readw(regs, MUSB_TXCSR) + & MUSB_TXCSR_P_SENDSTALL; + else + tmp = musb_readw(regs, MUSB_RXCSR) + & MUSB_RXCSR_P_SENDSTALL; + musb_ep_select(mbase, 0); + + result[0] = tmp ? 1 : 0; + } break; + + default: + /* class, vendor, etc ... delegate */ + handled = 0; + break; + } + + /* fill up the fifo; caller updates csr0 */ + if (handled > 0) { + u16 len = le16_to_cpu(ctrlrequest->wLength); + + if (len > 2) + len = 2; + musb_write_fifo(&musb->endpoints[0], len, result); + } + + return handled; +} + +/* + * handle a control-IN request, the end0 buffer contains the current request + * that is supposed to be a standard control request. Assumes the fifo to + * be at least 2 bytes long. + * + * @return 0 if the request was NOT HANDLED, + * < 0 when error + * > 0 when the request is processed + * + * Context: caller holds controller lock + */ +static int +service_in_request(struct musb *musb, const struct usb_ctrlrequest *ctrlrequest) +{ + int handled = 0; /* not handled */ + + if ((ctrlrequest->bRequestType & USB_TYPE_MASK) + == USB_TYPE_STANDARD) { + switch (ctrlrequest->bRequest) { + case USB_REQ_GET_STATUS: + handled = service_tx_status_request(musb, + ctrlrequest); + break; + + /* case USB_REQ_SYNC_FRAME: */ + + default: + break; + } + } + return handled; +} + +/* + * Context: caller holds controller lock + */ +static void musb_g_ep0_giveback(struct musb *musb, struct usb_request *req) +{ + musb_g_giveback(&musb->endpoints[0].ep_in, req, 0); + musb->ep0_state = MUSB_EP0_STAGE_SETUP; +} + +/* + * Tries to start B-device HNP negotiation if enabled via sysfs + */ +static inline void musb_try_b_hnp_enable(struct musb *musb) +{ + void __iomem *mbase = musb->mregs; + u8 devctl; + + DBG(1, "HNP: Setting HR\n"); + devctl = musb_readb(mbase, MUSB_DEVCTL); + musb_writeb(mbase, MUSB_DEVCTL, devctl | MUSB_DEVCTL_HR); +} + +/* + * Handle all control requests with no DATA stage, including standard + * requests such as: + * USB_REQ_SET_CONFIGURATION, USB_REQ_SET_INTERFACE, unrecognized + * always delegated to the gadget driver + * USB_REQ_SET_ADDRESS, USB_REQ_CLEAR_FEATURE, USB_REQ_SET_FEATURE + * always handled here, except for class/vendor/... features + * + * Context: caller holds controller lock + */ +static int +service_zero_data_request(struct musb *musb, + struct usb_ctrlrequest *ctrlrequest) +__releases(musb->lock) +__acquires(musb->lock) +{ + int handled = -EINVAL; + void __iomem *mbase = musb->mregs; + const u8 recip = ctrlrequest->bRequestType & USB_RECIP_MASK; + + /* the gadget driver handles everything except what we MUST handle */ + if ((ctrlrequest->bRequestType & USB_TYPE_MASK) + == USB_TYPE_STANDARD) { + switch (ctrlrequest->bRequest) { + case USB_REQ_SET_ADDRESS: + /* change it after the status stage */ + musb->set_address = true; + musb->address = (u8) (ctrlrequest->wValue & 0x7f); + handled = 1; + break; + + case USB_REQ_CLEAR_FEATURE: + switch (recip) { + case USB_RECIP_DEVICE: + if (ctrlrequest->wValue + != USB_DEVICE_REMOTE_WAKEUP) + break; + musb->may_wakeup = 0; + handled = 1; + break; + case USB_RECIP_INTERFACE: + break; + case USB_RECIP_ENDPOINT:{ + const u8 num = ctrlrequest->wIndex & 0x0f; + struct musb_ep *musb_ep; + + if (num == 0 + || num >= MUSB_C_NUM_EPS + || ctrlrequest->wValue + != USB_ENDPOINT_HALT) + break; + + if (ctrlrequest->wIndex & USB_DIR_IN) + musb_ep = &musb->endpoints[num].ep_in; + else + musb_ep = &musb->endpoints[num].ep_out; + if (!musb_ep->desc) + break; + + /* REVISIT do it directly, no locking games */ + spin_unlock(&musb->lock); + musb_gadget_set_halt(&musb_ep->end_point, 0); + spin_lock(&musb->lock); + + /* select ep0 again */ + musb_ep_select(mbase, 0); + handled = 1; + } break; + default: + /* class, vendor, etc ... delegate */ + handled = 0; + break; + } + break; + + case USB_REQ_SET_FEATURE: + switch (recip) { + case USB_RECIP_DEVICE: + handled = 1; + switch (ctrlrequest->wValue) { + case USB_DEVICE_REMOTE_WAKEUP: + musb->may_wakeup = 1; + break; + case USB_DEVICE_TEST_MODE: + if (musb->g.speed != USB_SPEED_HIGH) + goto stall; + if (ctrlrequest->wIndex & 0xff) + goto stall; + + switch (ctrlrequest->wIndex >> 8) { + case 1: + pr_debug("TEST_J\n"); + /* TEST_J */ + musb->test_mode_nr = + MUSB_TEST_J; + break; + case 2: + /* TEST_K */ + pr_debug("TEST_K\n"); + musb->test_mode_nr = + MUSB_TEST_K; + break; + case 3: + /* TEST_SE0_NAK */ + pr_debug("TEST_SE0_NAK\n"); + musb->test_mode_nr = + MUSB_TEST_SE0_NAK; + break; + case 4: + /* TEST_PACKET */ + pr_debug("TEST_PACKET\n"); + musb->test_mode_nr = + MUSB_TEST_PACKET; + break; + default: + goto stall; + } + + /* enter test mode after irq */ + if (handled > 0) + musb->test_mode = true; + break; +#ifdef CONFIG_USB_MUSB_OTG + case USB_DEVICE_B_HNP_ENABLE: + if (!musb->g.is_otg) + goto stall; + musb->g.b_hnp_enable = 1; + musb_try_b_hnp_enable(musb); + break; + case USB_DEVICE_A_HNP_SUPPORT: + if (!musb->g.is_otg) + goto stall; + musb->g.a_hnp_support = 1; + break; + case USB_DEVICE_A_ALT_HNP_SUPPORT: + if (!musb->g.is_otg) + goto stall; + musb->g.a_alt_hnp_support = 1; + break; +#endif +stall: + default: + handled = -EINVAL; + break; + } + break; + + case USB_RECIP_INTERFACE: + break; + + case USB_RECIP_ENDPOINT:{ + const u8 epnum = + ctrlrequest->wIndex & 0x0f; + struct musb_ep *musb_ep; + struct musb_hw_ep *ep; + void __iomem *regs; + int is_in; + u16 csr; + + if (epnum == 0 + || epnum >= MUSB_C_NUM_EPS + || ctrlrequest->wValue + != USB_ENDPOINT_HALT) + break; + + ep = musb->endpoints + epnum; + regs = ep->regs; + is_in = ctrlrequest->wIndex & USB_DIR_IN; + if (is_in) + musb_ep = &ep->ep_in; + else + musb_ep = &ep->ep_out; + if (!musb_ep->desc) + break; + + musb_ep_select(mbase, epnum); + if (is_in) { + csr = musb_readw(regs, + MUSB_TXCSR); + if (csr & MUSB_TXCSR_FIFONOTEMPTY) + csr |= MUSB_TXCSR_FLUSHFIFO; + csr |= MUSB_TXCSR_P_SENDSTALL + | MUSB_TXCSR_CLRDATATOG + | MUSB_TXCSR_P_WZC_BITS; + musb_writew(regs, MUSB_TXCSR, + csr); + } else { + csr = musb_readw(regs, + MUSB_RXCSR); + csr |= MUSB_RXCSR_P_SENDSTALL + | MUSB_RXCSR_FLUSHFIFO + | MUSB_RXCSR_CLRDATATOG + | MUSB_TXCSR_P_WZC_BITS; + musb_writew(regs, MUSB_RXCSR, + csr); + } + + /* select ep0 again */ + musb_ep_select(mbase, 0); + handled = 1; + } break; + + default: + /* class, vendor, etc ... delegate */ + handled = 0; + break; + } + break; + default: + /* delegate SET_CONFIGURATION, etc */ + handled = 0; + } + } else + handled = 0; + return handled; +} + +/* we have an ep0out data packet + * Context: caller holds controller lock + */ +static void ep0_rxstate(struct musb *musb) +{ + void __iomem *regs = musb->control_ep->regs; + struct usb_request *req; + u16 tmp; + + req = next_ep0_request(musb); + + /* read packet and ack; or stall because of gadget driver bug: + * should have provided the rx buffer before setup() returned. + */ + if (req) { + void *buf = req->buf + req->actual; + unsigned len = req->length - req->actual; + + /* read the buffer */ + tmp = musb_readb(regs, MUSB_COUNT0); + if (tmp > len) { + req->status = -EOVERFLOW; + tmp = len; + } + musb_read_fifo(&musb->endpoints[0], tmp, buf); + req->actual += tmp; + tmp = MUSB_CSR0_P_SVDRXPKTRDY; + if (tmp < 64 || req->actual == req->length) { + musb->ep0_state = MUSB_EP0_STAGE_STATUSIN; + tmp |= MUSB_CSR0_P_DATAEND; + } else + req = NULL; + } else + tmp = MUSB_CSR0_P_SVDRXPKTRDY | MUSB_CSR0_P_SENDSTALL; + + + /* Completion handler may choose to stall, e.g. because the + * message just received holds invalid data. + */ + if (req) { + musb->ackpend = tmp; + musb_g_ep0_giveback(musb, req); + if (!musb->ackpend) + return; + musb->ackpend = 0; + } + musb_writew(regs, MUSB_CSR0, tmp); +} + +/* + * transmitting to the host (IN), this code might be called from IRQ + * and from kernel thread. + * + * Context: caller holds controller lock + */ +static void ep0_txstate(struct musb *musb) +{ + void __iomem *regs = musb->control_ep->regs; + struct usb_request *request = next_ep0_request(musb); + u16 csr = MUSB_CSR0_TXPKTRDY; + u8 *fifo_src; + u8 fifo_count; + + if (!request) { + /* WARN_ON(1); */ + DBG(2, "odd; csr0 %04x\n", musb_readw(regs, MUSB_CSR0)); + return; + } + + /* load the data */ + fifo_src = (u8 *) request->buf + request->actual; + fifo_count = min((unsigned) MUSB_EP0_FIFOSIZE, + request->length - request->actual); + musb_write_fifo(&musb->endpoints[0], fifo_count, fifo_src); + request->actual += fifo_count; + + /* update the flags */ + if (fifo_count < MUSB_MAX_END0_PACKET + || request->actual == request->length) { + musb->ep0_state = MUSB_EP0_STAGE_STATUSOUT; + csr |= MUSB_CSR0_P_DATAEND; + } else + request = NULL; + + /* report completions as soon as the fifo's loaded; there's no + * win in waiting till this last packet gets acked. (other than + * very precise fault reporting, needed by USB TMC; possible with + * this hardware, but not usable from portable gadget drivers.) + */ + if (request) { + musb->ackpend = csr; + musb_g_ep0_giveback(musb, request); + if (!musb->ackpend) + return; + musb->ackpend = 0; + } + + /* send it out, triggering a "txpktrdy cleared" irq */ + musb_writew(regs, MUSB_CSR0, csr); +} + +/* + * Read a SETUP packet (struct usb_ctrlrequest) from the hardware. + * Fields are left in USB byte-order. + * + * Context: caller holds controller lock. + */ +static void +musb_read_setup(struct musb *musb, struct usb_ctrlrequest *req) +{ + struct usb_request *r; + void __iomem *regs = musb->control_ep->regs; + + musb_read_fifo(&musb->endpoints[0], sizeof *req, (u8 *)req); + + /* NOTE: earlier 2.6 versions changed setup packets to host + * order, but now USB packets always stay in USB byte order. + */ + DBG(3, "SETUP req%02x.%02x v%04x i%04x l%d\n", + req->bRequestType, + req->bRequest, + le16_to_cpu(req->wValue), + le16_to_cpu(req->wIndex), + le16_to_cpu(req->wLength)); + + /* clean up any leftover transfers */ + r = next_ep0_request(musb); + if (r) + musb_g_ep0_giveback(musb, r); + + /* For zero-data requests we want to delay the STATUS stage to + * avoid SETUPEND errors. If we read data (OUT), delay accepting + * packets until there's a buffer to store them in. + * + * If we write data, the controller acts happier if we enable + * the TX FIFO right away, and give the controller a moment + * to switch modes... + */ + musb->set_address = false; + musb->ackpend = MUSB_CSR0_P_SVDRXPKTRDY; + if (req->wLength == 0) { + if (req->bRequestType & USB_DIR_IN) + musb->ackpend |= MUSB_CSR0_TXPKTRDY; + musb->ep0_state = MUSB_EP0_STAGE_ACKWAIT; + } else if (req->bRequestType & USB_DIR_IN) { + musb->ep0_state = MUSB_EP0_STAGE_TX; + musb_writew(regs, MUSB_CSR0, MUSB_CSR0_P_SVDRXPKTRDY); + while ((musb_readw(regs, MUSB_CSR0) + & MUSB_CSR0_RXPKTRDY) != 0) + cpu_relax(); + musb->ackpend = 0; + } else + musb->ep0_state = MUSB_EP0_STAGE_RX; +} + +static int +forward_to_driver(struct musb *musb, const struct usb_ctrlrequest *ctrlrequest) +__releases(musb->lock) +__acquires(musb->lock) +{ + int retval; + if (!musb->gadget_driver) + return -EOPNOTSUPP; + spin_unlock(&musb->lock); + retval = musb->gadget_driver->setup(&musb->g, ctrlrequest); + spin_lock(&musb->lock); + return retval; +} + +/* + * Handle peripheral ep0 interrupt + * + * Context: irq handler; we won't re-enter the driver that way. + */ +irqreturn_t musb_g_ep0_irq(struct musb *musb) +{ + u16 csr; + u16 len; + void __iomem *mbase = musb->mregs; + void __iomem *regs = musb->endpoints[0].regs; + irqreturn_t retval = IRQ_NONE; + + musb_ep_select(mbase, 0); /* select ep0 */ + csr = musb_readw(regs, MUSB_CSR0); + len = musb_readb(regs, MUSB_COUNT0); + + DBG(4, "csr %04x, count %d, myaddr %d, ep0stage %s\n", + csr, len, + musb_readb(mbase, MUSB_FADDR), + decode_ep0stage(musb->ep0_state)); + + /* I sent a stall.. need to acknowledge it now.. */ + if (csr & MUSB_CSR0_P_SENTSTALL) { + musb_writew(regs, MUSB_CSR0, + csr & ~MUSB_CSR0_P_SENTSTALL); + retval = IRQ_HANDLED; + musb->ep0_state = MUSB_EP0_STAGE_SETUP; + csr = musb_readw(regs, MUSB_CSR0); + } + + /* request ended "early" */ + if (csr & MUSB_CSR0_P_SETUPEND) { + musb_writew(regs, MUSB_CSR0, MUSB_CSR0_P_SVDSETUPEND); + retval = IRQ_HANDLED; + musb->ep0_state = MUSB_EP0_STAGE_SETUP; + csr = musb_readw(regs, MUSB_CSR0); + /* NOTE: request may need completion */ + } + + /* docs from Mentor only describe tx, rx, and idle/setup states. + * we need to handle nuances around status stages, and also the + * case where status and setup stages come back-to-back ... + */ + switch (musb->ep0_state) { + + case MUSB_EP0_STAGE_TX: + /* irq on clearing txpktrdy */ + if ((csr & MUSB_CSR0_TXPKTRDY) == 0) { + ep0_txstate(musb); + retval = IRQ_HANDLED; + } + break; + + case MUSB_EP0_STAGE_RX: + /* irq on set rxpktrdy */ + if (csr & MUSB_CSR0_RXPKTRDY) { + ep0_rxstate(musb); + retval = IRQ_HANDLED; + } + break; + + case MUSB_EP0_STAGE_STATUSIN: + /* end of sequence #2 (OUT/RX state) or #3 (no data) */ + + /* update address (if needed) only @ the end of the + * status phase per usb spec, which also guarantees + * we get 10 msec to receive this irq... until this + * is done we won't see the next packet. + */ + if (musb->set_address) { + musb->set_address = false; + musb_writeb(mbase, MUSB_FADDR, musb->address); + } + + /* enter test mode if needed (exit by reset) */ + else if (musb->test_mode) { + DBG(1, "entering TESTMODE\n"); + + if (MUSB_TEST_PACKET == musb->test_mode_nr) + musb_load_testpacket(musb); + + musb_writeb(mbase, MUSB_TESTMODE, + musb->test_mode_nr); + } + /* FALLTHROUGH */ + + case MUSB_EP0_STAGE_STATUSOUT: + /* end of sequence #1: write to host (TX state) */ + { + struct usb_request *req; + + req = next_ep0_request(musb); + if (req) + musb_g_ep0_giveback(musb, req); + } + retval = IRQ_HANDLED; + musb->ep0_state = MUSB_EP0_STAGE_SETUP; + /* FALLTHROUGH */ + + case MUSB_EP0_STAGE_SETUP: + if (csr & MUSB_CSR0_RXPKTRDY) { + struct usb_ctrlrequest setup; + int handled = 0; + + if (len != 8) { + ERR("SETUP packet len %d != 8 ?\n", len); + break; + } + musb_read_setup(musb, &setup); + retval = IRQ_HANDLED; + + /* sometimes the RESET won't be reported */ + if (unlikely(musb->g.speed == USB_SPEED_UNKNOWN)) { + u8 power; + + printk(KERN_NOTICE "%s: peripheral reset " + "irq lost!\n", + musb_driver_name); + power = musb_readb(mbase, MUSB_POWER); + musb->g.speed = (power & MUSB_POWER_HSMODE) + ? USB_SPEED_HIGH : USB_SPEED_FULL; + + } + + switch (musb->ep0_state) { + + /* sequence #3 (no data stage), includes requests + * we can't forward (notably SET_ADDRESS and the + * device/endpoint feature set/clear operations) + * plus SET_CONFIGURATION and others we must + */ + case MUSB_EP0_STAGE_ACKWAIT: + handled = service_zero_data_request( + musb, &setup); + + /* status stage might be immediate */ + if (handled > 0) { + musb->ackpend |= MUSB_CSR0_P_DATAEND; + musb->ep0_state = + MUSB_EP0_STAGE_STATUSIN; + } + break; + + /* sequence #1 (IN to host), includes GET_STATUS + * requests that we can't forward, GET_DESCRIPTOR + * and others that we must + */ + case MUSB_EP0_STAGE_TX: + handled = service_in_request(musb, &setup); + if (handled > 0) { + musb->ackpend = MUSB_CSR0_TXPKTRDY + | MUSB_CSR0_P_DATAEND; + musb->ep0_state = + MUSB_EP0_STAGE_STATUSOUT; + } + break; + + /* sequence #2 (OUT from host), always forward */ + default: /* MUSB_EP0_STAGE_RX */ + break; + } + + DBG(3, "handled %d, csr %04x, ep0stage %s\n", + handled, csr, + decode_ep0stage(musb->ep0_state)); + + /* unless we need to delegate this to the gadget + * driver, we know how to wrap this up: csr0 has + * not yet been written. + */ + if (handled < 0) + goto stall; + else if (handled > 0) + goto finish; + + handled = forward_to_driver(musb, &setup); + if (handled < 0) { + musb_ep_select(mbase, 0); +stall: + DBG(3, "stall (%d)\n", handled); + musb->ackpend |= MUSB_CSR0_P_SENDSTALL; + musb->ep0_state = MUSB_EP0_STAGE_SETUP; +finish: + musb_writew(regs, MUSB_CSR0, + musb->ackpend); + musb->ackpend = 0; + } + } + break; + + case MUSB_EP0_STAGE_ACKWAIT: + /* This should not happen. But happens with tusb6010 with + * g_file_storage and high speed. Do nothing. + */ + retval = IRQ_HANDLED; + break; + + default: + /* "can't happen" */ + WARN_ON(1); + musb_writew(regs, MUSB_CSR0, MUSB_CSR0_P_SENDSTALL); + musb->ep0_state = MUSB_EP0_STAGE_SETUP; + break; + } + + return retval; +} + + +static int +musb_g_ep0_enable(struct usb_ep *ep, const struct usb_endpoint_descriptor *desc) +{ + /* always enabled */ + return -EINVAL; +} + +static int musb_g_ep0_disable(struct usb_ep *e) +{ + /* always enabled */ + return -EINVAL; +} + +static int +musb_g_ep0_queue(struct usb_ep *e, struct usb_request *r, gfp_t gfp_flags) +{ + struct musb_ep *ep; + struct musb_request *req; + struct musb *musb; + int status; + unsigned long lockflags; + void __iomem *regs; + + if (!e || !r) + return -EINVAL; + + ep = to_musb_ep(e); + musb = ep->musb; + regs = musb->control_ep->regs; + + req = to_musb_request(r); + req->musb = musb; + req->request.actual = 0; + req->request.status = -EINPROGRESS; + req->tx = ep->is_in; + + spin_lock_irqsave(&musb->lock, lockflags); + + if (!list_empty(&ep->req_list)) { + status = -EBUSY; + goto cleanup; + } + + switch (musb->ep0_state) { + case MUSB_EP0_STAGE_RX: /* control-OUT data */ + case MUSB_EP0_STAGE_TX: /* control-IN data */ + case MUSB_EP0_STAGE_ACKWAIT: /* zero-length data */ + status = 0; + break; + default: + DBG(1, "ep0 request queued in state %d\n", + musb->ep0_state); + status = -EINVAL; + goto cleanup; + } + + /* add request to the list */ + list_add_tail(&(req->request.list), &(ep->req_list)); + + DBG(3, "queue to %s (%s), length=%d\n", + ep->name, ep->is_in ? "IN/TX" : "OUT/RX", + req->request.length); + + musb_ep_select(musb->mregs, 0); + + /* sequence #1, IN ... start writing the data */ + if (musb->ep0_state == MUSB_EP0_STAGE_TX) + ep0_txstate(musb); + + /* sequence #3, no-data ... issue IN status */ + else if (musb->ep0_state == MUSB_EP0_STAGE_ACKWAIT) { + if (req->request.length) + status = -EINVAL; + else { + musb->ep0_state = MUSB_EP0_STAGE_STATUSIN; + musb_writew(regs, MUSB_CSR0, + musb->ackpend | MUSB_CSR0_P_DATAEND); + musb->ackpend = 0; + musb_g_ep0_giveback(ep->musb, r); + } + + /* else for sequence #2 (OUT), caller provides a buffer + * before the next packet arrives. deferred responses + * (after SETUP is acked) are racey. + */ + } else if (musb->ackpend) { + musb_writew(regs, MUSB_CSR0, musb->ackpend); + musb->ackpend = 0; + } + +cleanup: + spin_unlock_irqrestore(&musb->lock, lockflags); + return status; +} + +static int musb_g_ep0_dequeue(struct usb_ep *ep, struct usb_request *req) +{ + /* we just won't support this */ + return -EINVAL; +} + +static int musb_g_ep0_halt(struct usb_ep *e, int value) +{ + struct musb_ep *ep; + struct musb *musb; + void __iomem *base, *regs; + unsigned long flags; + int status; + u16 csr; + + if (!e || !value) + return -EINVAL; + + ep = to_musb_ep(e); + musb = ep->musb; + base = musb->mregs; + regs = musb->control_ep->regs; + status = 0; + + spin_lock_irqsave(&musb->lock, flags); + + if (!list_empty(&ep->req_list)) { + status = -EBUSY; + goto cleanup; + } + + musb_ep_select(base, 0); + csr = musb->ackpend; + + switch (musb->ep0_state) { + + /* Stalls are usually issued after parsing SETUP packet, either + * directly in irq context from setup() or else later. + */ + case MUSB_EP0_STAGE_TX: /* control-IN data */ + case MUSB_EP0_STAGE_ACKWAIT: /* STALL for zero-length data */ + case MUSB_EP0_STAGE_RX: /* control-OUT data */ + csr = musb_readw(regs, MUSB_CSR0); + /* FALLTHROUGH */ + + /* It's also OK to issue stalls during callbacks when a non-empty + * DATA stage buffer has been read (or even written). + */ + case MUSB_EP0_STAGE_STATUSIN: /* control-OUT status */ + case MUSB_EP0_STAGE_STATUSOUT: /* control-IN status */ + + csr |= MUSB_CSR0_P_SENDSTALL; + musb_writew(regs, MUSB_CSR0, csr); + musb->ep0_state = MUSB_EP0_STAGE_SETUP; + musb->ackpend = 0; + break; + default: + DBG(1, "ep0 can't halt in state %d\n", musb->ep0_state); + status = -EINVAL; + } + +cleanup: + spin_unlock_irqrestore(&musb->lock, flags); + return status; +} + +const struct usb_ep_ops musb_g_ep0_ops = { + .enable = musb_g_ep0_enable, + .disable = musb_g_ep0_disable, + .alloc_request = musb_alloc_request, + .free_request = musb_free_request, + .queue = musb_g_ep0_queue, + .dequeue = musb_g_ep0_dequeue, + .set_halt = musb_g_ep0_halt, +}; diff --git a/drivers/usb/musb/musb_host.c b/drivers/usb/musb/musb_host.c new file mode 100644 index 00000000000..8b4be012669 --- /dev/null +++ b/drivers/usb/musb/musb_host.c @@ -0,0 +1,2170 @@ +/* + * MUSB OTG driver host support + * + * Copyright 2005 Mentor Graphics Corporation + * Copyright (C) 2005-2006 by Texas Instruments + * Copyright (C) 2006-2007 Nokia Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include "musb_core.h" +#include "musb_host.h" + + +/* MUSB HOST status 22-mar-2006 + * + * - There's still lots of partial code duplication for fault paths, so + * they aren't handled as consistently as they need to be. + * + * - PIO mostly behaved when last tested. + * + including ep0, with all usbtest cases 9, 10 + * + usbtest 14 (ep0out) doesn't seem to run at all + * + double buffered OUT/TX endpoints saw stalls(!) with certain usbtest + * configurations, but otherwise double buffering passes basic tests. + * + for 2.6.N, for N > ~10, needs API changes for hcd framework. + * + * - DMA (CPPI) ... partially behaves, not currently recommended + * + about 1/15 the speed of typical EHCI implementations (PCI) + * + RX, all too often reqpkt seems to misbehave after tx + * + TX, no known issues (other than evident silicon issue) + * + * - DMA (Mentor/OMAP) ...has at least toggle update problems + * + * - Still no traffic scheduling code to make NAKing for bulk or control + * transfers unable to starve other requests; or to make efficient use + * of hardware with periodic transfers. (Note that network drivers + * commonly post bulk reads that stay pending for a long time; these + * would make very visible trouble.) + * + * - Not tested with HNP, but some SRP paths seem to behave. + * + * NOTE 24-August-2006: + * + * - Bulk traffic finally uses both sides of hardware ep1, freeing up an + * extra endpoint for periodic use enabling hub + keybd + mouse. That + * mostly works, except that with "usbnet" it's easy to trigger cases + * with "ping" where RX loses. (a) ping to davinci, even "ping -f", + * fine; but (b) ping _from_ davinci, even "ping -c 1", ICMP RX loses + * although ARP RX wins. (That test was done with a full speed link.) + */ + + +/* + * NOTE on endpoint usage: + * + * CONTROL transfers all go through ep0. BULK ones go through dedicated IN + * and OUT endpoints ... hardware is dedicated for those "async" queue(s). + * + * (Yes, bulk _could_ use more of the endpoints than that, and would even + * benefit from it ... one remote device may easily be NAKing while others + * need to perform transfers in that same direction. The same thing could + * be done in software though, assuming dma cooperates.) + * + * INTERUPPT and ISOCHRONOUS transfers are scheduled to the other endpoints. + * So far that scheduling is both dumb and optimistic: the endpoint will be + * "claimed" until its software queue is no longer refilled. No multiplexing + * of transfers between endpoints, or anything clever. + */ + + +static void musb_ep_program(struct musb *musb, u8 epnum, + struct urb *urb, unsigned int nOut, + u8 *buf, u32 len); + +/* + * Clear TX fifo. Needed to avoid BABBLE errors. + */ +static inline void musb_h_tx_flush_fifo(struct musb_hw_ep *ep) +{ + void __iomem *epio = ep->regs; + u16 csr; + int retries = 1000; + + csr = musb_readw(epio, MUSB_TXCSR); + while (csr & MUSB_TXCSR_FIFONOTEMPTY) { + DBG(5, "Host TX FIFONOTEMPTY csr: %02x\n", csr); + csr |= MUSB_TXCSR_FLUSHFIFO; + musb_writew(epio, MUSB_TXCSR, csr); + csr = musb_readw(epio, MUSB_TXCSR); + if (retries-- < 1) { + ERR("Could not flush host TX fifo: csr: %04x\n", csr); + return; + } + mdelay(1); + } +} + +/* + * Start transmit. Caller is responsible for locking shared resources. + * musb must be locked. + */ +static inline void musb_h_tx_start(struct musb_hw_ep *ep) +{ + u16 txcsr; + + /* NOTE: no locks here; caller should lock and select EP */ + if (ep->epnum) { + txcsr = musb_readw(ep->regs, MUSB_TXCSR); + txcsr |= MUSB_TXCSR_TXPKTRDY | MUSB_TXCSR_H_WZC_BITS; + musb_writew(ep->regs, MUSB_TXCSR, txcsr); + } else { + txcsr = MUSB_CSR0_H_SETUPPKT | MUSB_CSR0_TXPKTRDY; + musb_writew(ep->regs, MUSB_CSR0, txcsr); + } + +} + +static inline void cppi_host_txdma_start(struct musb_hw_ep *ep) +{ + u16 txcsr; + + /* NOTE: no locks here; caller should lock and select EP */ + txcsr = musb_readw(ep->regs, MUSB_TXCSR); + txcsr |= MUSB_TXCSR_DMAENAB | MUSB_TXCSR_H_WZC_BITS; + musb_writew(ep->regs, MUSB_TXCSR, txcsr); +} + +/* + * Start the URB at the front of an endpoint's queue + * end must be claimed from the caller. + * + * Context: controller locked, irqs blocked + */ +static void +musb_start_urb(struct musb *musb, int is_in, struct musb_qh *qh) +{ + u16 frame; + u32 len; + void *buf; + void __iomem *mbase = musb->mregs; + struct urb *urb = next_urb(qh); + struct musb_hw_ep *hw_ep = qh->hw_ep; + unsigned pipe = urb->pipe; + u8 address = usb_pipedevice(pipe); + int epnum = hw_ep->epnum; + + /* initialize software qh state */ + qh->offset = 0; + qh->segsize = 0; + + /* gather right source of data */ + switch (qh->type) { + case USB_ENDPOINT_XFER_CONTROL: + /* control transfers always start with SETUP */ + is_in = 0; + hw_ep->out_qh = qh; + musb->ep0_stage = MUSB_EP0_START; + buf = urb->setup_packet; + len = 8; + break; + case USB_ENDPOINT_XFER_ISOC: + qh->iso_idx = 0; + qh->frame = 0; + buf = urb->transfer_buffer + urb->iso_frame_desc[0].offset; + len = urb->iso_frame_desc[0].length; + break; + default: /* bulk, interrupt */ + buf = urb->transfer_buffer; + len = urb->transfer_buffer_length; + } + + DBG(4, "qh %p urb %p dev%d ep%d%s%s, hw_ep %d, %p/%d\n", + qh, urb, address, qh->epnum, + is_in ? "in" : "out", + ({char *s; switch (qh->type) { + case USB_ENDPOINT_XFER_CONTROL: s = ""; break; + case USB_ENDPOINT_XFER_BULK: s = "-bulk"; break; + case USB_ENDPOINT_XFER_ISOC: s = "-iso"; break; + default: s = "-intr"; break; + }; s; }), + epnum, buf, len); + + /* Configure endpoint */ + if (is_in || hw_ep->is_shared_fifo) + hw_ep->in_qh = qh; + else + hw_ep->out_qh = qh; + musb_ep_program(musb, epnum, urb, !is_in, buf, len); + + /* transmit may have more work: start it when it is time */ + if (is_in) + return; + + /* determine if the time is right for a periodic transfer */ + switch (qh->type) { + case USB_ENDPOINT_XFER_ISOC: + case USB_ENDPOINT_XFER_INT: + DBG(3, "check whether there's still time for periodic Tx\n"); + qh->iso_idx = 0; + frame = musb_readw(mbase, MUSB_FRAME); + /* FIXME this doesn't implement that scheduling policy ... + * or handle framecounter wrapping + */ + if ((urb->transfer_flags & URB_ISO_ASAP) + || (frame >= urb->start_frame)) { + /* REVISIT the SOF irq handler shouldn't duplicate + * this code; and we don't init urb->start_frame... + */ + qh->frame = 0; + goto start; + } else { + qh->frame = urb->start_frame; + /* enable SOF interrupt so we can count down */ + DBG(1, "SOF for %d\n", epnum); +#if 1 /* ifndef CONFIG_ARCH_DAVINCI */ + musb_writeb(mbase, MUSB_INTRUSBE, 0xff); +#endif + } + break; + default: +start: + DBG(4, "Start TX%d %s\n", epnum, + hw_ep->tx_channel ? "dma" : "pio"); + + if (!hw_ep->tx_channel) + musb_h_tx_start(hw_ep); + else if (is_cppi_enabled() || tusb_dma_omap()) + cppi_host_txdma_start(hw_ep); + } +} + +/* caller owns controller lock, irqs are blocked */ +static void +__musb_giveback(struct musb *musb, struct urb *urb, int status) +__releases(musb->lock) +__acquires(musb->lock) +{ + DBG(({ int level; switch (urb->status) { + case 0: + level = 4; + break; + /* common/boring faults */ + case -EREMOTEIO: + case -ESHUTDOWN: + case -ECONNRESET: + case -EPIPE: + level = 3; + break; + default: + level = 2; + break; + }; level; }), + "complete %p (%d), dev%d ep%d%s, %d/%d\n", + urb, urb->status, + usb_pipedevice(urb->pipe), + usb_pipeendpoint(urb->pipe), + usb_pipein(urb->pipe) ? "in" : "out", + urb->actual_length, urb->transfer_buffer_length + ); + + spin_unlock(&musb->lock); + usb_hcd_giveback_urb(musb_to_hcd(musb), urb, status); + spin_lock(&musb->lock); +} + +/* for bulk/interrupt endpoints only */ +static inline void +musb_save_toggle(struct musb_hw_ep *ep, int is_in, struct urb *urb) +{ + struct usb_device *udev = urb->dev; + u16 csr; + void __iomem *epio = ep->regs; + struct musb_qh *qh; + + /* FIXME: the current Mentor DMA code seems to have + * problems getting toggle correct. + */ + + if (is_in || ep->is_shared_fifo) + qh = ep->in_qh; + else + qh = ep->out_qh; + + if (!is_in) { + csr = musb_readw(epio, MUSB_TXCSR); + usb_settoggle(udev, qh->epnum, 1, + (csr & MUSB_TXCSR_H_DATATOGGLE) + ? 1 : 0); + } else { + csr = musb_readw(epio, MUSB_RXCSR); + usb_settoggle(udev, qh->epnum, 0, + (csr & MUSB_RXCSR_H_DATATOGGLE) + ? 1 : 0); + } +} + +/* caller owns controller lock, irqs are blocked */ +static struct musb_qh * +musb_giveback(struct musb_qh *qh, struct urb *urb, int status) +{ + int is_in; + struct musb_hw_ep *ep = qh->hw_ep; + struct musb *musb = ep->musb; + int ready = qh->is_ready; + + if (ep->is_shared_fifo) + is_in = 1; + else + is_in = usb_pipein(urb->pipe); + + /* save toggle eagerly, for paranoia */ + switch (qh->type) { + case USB_ENDPOINT_XFER_BULK: + case USB_ENDPOINT_XFER_INT: + musb_save_toggle(ep, is_in, urb); + break; + case USB_ENDPOINT_XFER_ISOC: + if (status == 0 && urb->error_count) + status = -EXDEV; + break; + } + + usb_hcd_unlink_urb_from_ep(musb_to_hcd(musb), urb); + + qh->is_ready = 0; + __musb_giveback(musb, urb, status); + qh->is_ready = ready; + + /* reclaim resources (and bandwidth) ASAP; deschedule it, and + * invalidate qh as soon as list_empty(&hep->urb_list) + */ + if (list_empty(&qh->hep->urb_list)) { + struct list_head *head; + + if (is_in) + ep->rx_reinit = 1; + else + ep->tx_reinit = 1; + + /* clobber old pointers to this qh */ + if (is_in || ep->is_shared_fifo) + ep->in_qh = NULL; + else + ep->out_qh = NULL; + qh->hep->hcpriv = NULL; + + switch (qh->type) { + + case USB_ENDPOINT_XFER_ISOC: + case USB_ENDPOINT_XFER_INT: + /* this is where periodic bandwidth should be + * de-allocated if it's tracked and allocated; + * and where we'd update the schedule tree... + */ + musb->periodic[ep->epnum] = NULL; + kfree(qh); + qh = NULL; + break; + + case USB_ENDPOINT_XFER_CONTROL: + case USB_ENDPOINT_XFER_BULK: + /* fifo policy for these lists, except that NAKing + * should rotate a qh to the end (for fairness). + */ + head = qh->ring.prev; + list_del(&qh->ring); + kfree(qh); + qh = first_qh(head); + break; + } + } + return qh; +} + +/* + * Advance this hardware endpoint's queue, completing the specified urb and + * advancing to either the next urb queued to that qh, or else invalidating + * that qh and advancing to the next qh scheduled after the current one. + * + * Context: caller owns controller lock, irqs are blocked + */ +static void +musb_advance_schedule(struct musb *musb, struct urb *urb, + struct musb_hw_ep *hw_ep, int is_in) +{ + struct musb_qh *qh; + + if (is_in || hw_ep->is_shared_fifo) + qh = hw_ep->in_qh; + else + qh = hw_ep->out_qh; + + if (urb->status == -EINPROGRESS) + qh = musb_giveback(qh, urb, 0); + else + qh = musb_giveback(qh, urb, urb->status); + + if (qh && qh->is_ready && !list_empty(&qh->hep->urb_list)) { + DBG(4, "... next ep%d %cX urb %p\n", + hw_ep->epnum, is_in ? 'R' : 'T', + next_urb(qh)); + musb_start_urb(musb, is_in, qh); + } +} + +static inline u16 musb_h_flush_rxfifo(struct musb_hw_ep *hw_ep, u16 csr) +{ + /* we don't want fifo to fill itself again; + * ignore dma (various models), + * leave toggle alone (may not have been saved yet) + */ + csr |= MUSB_RXCSR_FLUSHFIFO | MUSB_RXCSR_RXPKTRDY; + csr &= ~(MUSB_RXCSR_H_REQPKT + | MUSB_RXCSR_H_AUTOREQ + | MUSB_RXCSR_AUTOCLEAR); + + /* write 2x to allow double buffering */ + musb_writew(hw_ep->regs, MUSB_RXCSR, csr); + musb_writew(hw_ep->regs, MUSB_RXCSR, csr); + + /* flush writebuffer */ + return musb_readw(hw_ep->regs, MUSB_RXCSR); +} + +/* + * PIO RX for a packet (or part of it). + */ +static bool +musb_host_packet_rx(struct musb *musb, struct urb *urb, u8 epnum, u8 iso_err) +{ + u16 rx_count; + u8 *buf; + u16 csr; + bool done = false; + u32 length; + int do_flush = 0; + struct musb_hw_ep *hw_ep = musb->endpoints + epnum; + void __iomem *epio = hw_ep->regs; + struct musb_qh *qh = hw_ep->in_qh; + int pipe = urb->pipe; + void *buffer = urb->transfer_buffer; + + /* musb_ep_select(mbase, epnum); */ + rx_count = musb_readw(epio, MUSB_RXCOUNT); + DBG(3, "RX%d count %d, buffer %p len %d/%d\n", epnum, rx_count, + urb->transfer_buffer, qh->offset, + urb->transfer_buffer_length); + + /* unload FIFO */ + if (usb_pipeisoc(pipe)) { + int status = 0; + struct usb_iso_packet_descriptor *d; + + if (iso_err) { + status = -EILSEQ; + urb->error_count++; + } + + d = urb->iso_frame_desc + qh->iso_idx; + buf = buffer + d->offset; + length = d->length; + if (rx_count > length) { + if (status == 0) { + status = -EOVERFLOW; + urb->error_count++; + } + DBG(2, "** OVERFLOW %d into %d\n", rx_count, length); + do_flush = 1; + } else + length = rx_count; + urb->actual_length += length; + d->actual_length = length; + + d->status = status; + + /* see if we are done */ + done = (++qh->iso_idx >= urb->number_of_packets); + } else { + /* non-isoch */ + buf = buffer + qh->offset; + length = urb->transfer_buffer_length - qh->offset; + if (rx_count > length) { + if (urb->status == -EINPROGRESS) + urb->status = -EOVERFLOW; + DBG(2, "** OVERFLOW %d into %d\n", rx_count, length); + do_flush = 1; + } else + length = rx_count; + urb->actual_length += length; + qh->offset += length; + + /* see if we are done */ + done = (urb->actual_length == urb->transfer_buffer_length) + || (rx_count < qh->maxpacket) + || (urb->status != -EINPROGRESS); + if (done + && (urb->status == -EINPROGRESS) + && (urb->transfer_flags & URB_SHORT_NOT_OK) + && (urb->actual_length + < urb->transfer_buffer_length)) + urb->status = -EREMOTEIO; + } + + musb_read_fifo(hw_ep, length, buf); + + csr = musb_readw(epio, MUSB_RXCSR); + csr |= MUSB_RXCSR_H_WZC_BITS; + if (unlikely(do_flush)) + musb_h_flush_rxfifo(hw_ep, csr); + else { + /* REVISIT this assumes AUTOCLEAR is never set */ + csr &= ~(MUSB_RXCSR_RXPKTRDY | MUSB_RXCSR_H_REQPKT); + if (!done) + csr |= MUSB_RXCSR_H_REQPKT; + musb_writew(epio, MUSB_RXCSR, csr); + } + + return done; +} + +/* we don't always need to reinit a given side of an endpoint... + * when we do, use tx/rx reinit routine and then construct a new CSR + * to address data toggle, NYET, and DMA or PIO. + * + * it's possible that driver bugs (especially for DMA) or aborting a + * transfer might have left the endpoint busier than it should be. + * the busy/not-empty tests are basically paranoia. + */ +static void +musb_rx_reinit(struct musb *musb, struct musb_qh *qh, struct musb_hw_ep *ep) +{ + u16 csr; + + /* NOTE: we know the "rx" fifo reinit never triggers for ep0. + * That always uses tx_reinit since ep0 repurposes TX register + * offsets; the initial SETUP packet is also a kind of OUT. + */ + + /* if programmed for Tx, put it in RX mode */ + if (ep->is_shared_fifo) { + csr = musb_readw(ep->regs, MUSB_TXCSR); + if (csr & MUSB_TXCSR_MODE) { + musb_h_tx_flush_fifo(ep); + musb_writew(ep->regs, MUSB_TXCSR, + MUSB_TXCSR_FRCDATATOG); + } + /* clear mode (and everything else) to enable Rx */ + musb_writew(ep->regs, MUSB_TXCSR, 0); + + /* scrub all previous state, clearing toggle */ + } else { + csr = musb_readw(ep->regs, MUSB_RXCSR); + if (csr & MUSB_RXCSR_RXPKTRDY) + WARNING("rx%d, packet/%d ready?\n", ep->epnum, + musb_readw(ep->regs, MUSB_RXCOUNT)); + + musb_h_flush_rxfifo(ep, MUSB_RXCSR_CLRDATATOG); + } + + /* target addr and (for multipoint) hub addr/port */ + if (musb->is_multipoint) { + musb_writeb(ep->target_regs, MUSB_RXFUNCADDR, + qh->addr_reg); + musb_writeb(ep->target_regs, MUSB_RXHUBADDR, + qh->h_addr_reg); + musb_writeb(ep->target_regs, MUSB_RXHUBPORT, + qh->h_port_reg); + } else + musb_writeb(musb->mregs, MUSB_FADDR, qh->addr_reg); + + /* protocol/endpoint, interval/NAKlimit, i/o size */ + musb_writeb(ep->regs, MUSB_RXTYPE, qh->type_reg); + musb_writeb(ep->regs, MUSB_RXINTERVAL, qh->intv_reg); + /* NOTE: bulk combining rewrites high bits of maxpacket */ + musb_writew(ep->regs, MUSB_RXMAXP, qh->maxpacket); + + ep->rx_reinit = 0; +} + + +/* + * Program an HDRC endpoint as per the given URB + * Context: irqs blocked, controller lock held + */ +static void musb_ep_program(struct musb *musb, u8 epnum, + struct urb *urb, unsigned int is_out, + u8 *buf, u32 len) +{ + struct dma_controller *dma_controller; + struct dma_channel *dma_channel; + u8 dma_ok; + void __iomem *mbase = musb->mregs; + struct musb_hw_ep *hw_ep = musb->endpoints + epnum; + void __iomem *epio = hw_ep->regs; + struct musb_qh *qh; + u16 packet_sz; + + if (!is_out || hw_ep->is_shared_fifo) + qh = hw_ep->in_qh; + else + qh = hw_ep->out_qh; + + packet_sz = qh->maxpacket; + + DBG(3, "%s hw%d urb %p spd%d dev%d ep%d%s " + "h_addr%02x h_port%02x bytes %d\n", + is_out ? "-->" : "<--", + epnum, urb, urb->dev->speed, + qh->addr_reg, qh->epnum, is_out ? "out" : "in", + qh->h_addr_reg, qh->h_port_reg, + len); + + musb_ep_select(mbase, epnum); + + /* candidate for DMA? */ + dma_controller = musb->dma_controller; + if (is_dma_capable() && epnum && dma_controller) { + dma_channel = is_out ? hw_ep->tx_channel : hw_ep->rx_channel; + if (!dma_channel) { + dma_channel = dma_controller->channel_alloc( + dma_controller, hw_ep, is_out); + if (is_out) + hw_ep->tx_channel = dma_channel; + else + hw_ep->rx_channel = dma_channel; + } + } else + dma_channel = NULL; + + /* make sure we clear DMAEnab, autoSet bits from previous run */ + + /* OUT/transmit/EP0 or IN/receive? */ + if (is_out) { + u16 csr; + u16 int_txe; + u16 load_count; + + csr = musb_readw(epio, MUSB_TXCSR); + + /* disable interrupt in case we flush */ + int_txe = musb_readw(mbase, MUSB_INTRTXE); + musb_writew(mbase, MUSB_INTRTXE, int_txe & ~(1 << epnum)); + + /* general endpoint setup */ + if (epnum) { + /* ASSERT: TXCSR_DMAENAB was already cleared */ + + /* flush all old state, set default */ + musb_h_tx_flush_fifo(hw_ep); + csr &= ~(MUSB_TXCSR_H_NAKTIMEOUT + | MUSB_TXCSR_DMAMODE + | MUSB_TXCSR_FRCDATATOG + | MUSB_TXCSR_H_RXSTALL + | MUSB_TXCSR_H_ERROR + | MUSB_TXCSR_TXPKTRDY + ); + csr |= MUSB_TXCSR_MODE; + + if (usb_gettoggle(urb->dev, + qh->epnum, 1)) + csr |= MUSB_TXCSR_H_WR_DATATOGGLE + | MUSB_TXCSR_H_DATATOGGLE; + else + csr |= MUSB_TXCSR_CLRDATATOG; + + /* twice in case of double packet buffering */ + musb_writew(epio, MUSB_TXCSR, csr); + /* REVISIT may need to clear FLUSHFIFO ... */ + musb_writew(epio, MUSB_TXCSR, csr); + csr = musb_readw(epio, MUSB_TXCSR); + } else { + /* endpoint 0: just flush */ + musb_writew(epio, MUSB_CSR0, + csr | MUSB_CSR0_FLUSHFIFO); + musb_writew(epio, MUSB_CSR0, + csr | MUSB_CSR0_FLUSHFIFO); + } + + /* target addr and (for multipoint) hub addr/port */ + if (musb->is_multipoint) { + musb_writeb(mbase, + MUSB_BUSCTL_OFFSET(epnum, MUSB_TXFUNCADDR), + qh->addr_reg); + musb_writeb(mbase, + MUSB_BUSCTL_OFFSET(epnum, MUSB_TXHUBADDR), + qh->h_addr_reg); + musb_writeb(mbase, + MUSB_BUSCTL_OFFSET(epnum, MUSB_TXHUBPORT), + qh->h_port_reg); +/* FIXME if !epnum, do the same for RX ... */ + } else + musb_writeb(mbase, MUSB_FADDR, qh->addr_reg); + + /* protocol/endpoint/interval/NAKlimit */ + if (epnum) { + musb_writeb(epio, MUSB_TXTYPE, qh->type_reg); + if (can_bulk_split(musb, qh->type)) + musb_writew(epio, MUSB_TXMAXP, + packet_sz + | ((hw_ep->max_packet_sz_tx / + packet_sz) - 1) << 11); + else + musb_writew(epio, MUSB_TXMAXP, + packet_sz); + musb_writeb(epio, MUSB_TXINTERVAL, qh->intv_reg); + } else { + musb_writeb(epio, MUSB_NAKLIMIT0, qh->intv_reg); + if (musb->is_multipoint) + musb_writeb(epio, MUSB_TYPE0, + qh->type_reg); + } + + if (can_bulk_split(musb, qh->type)) + load_count = min((u32) hw_ep->max_packet_sz_tx, + len); + else + load_count = min((u32) packet_sz, len); + +#ifdef CONFIG_USB_INVENTRA_DMA + if (dma_channel) { + + /* clear previous state */ + csr = musb_readw(epio, MUSB_TXCSR); + csr &= ~(MUSB_TXCSR_AUTOSET + | MUSB_TXCSR_DMAMODE + | MUSB_TXCSR_DMAENAB); + csr |= MUSB_TXCSR_MODE; + musb_writew(epio, MUSB_TXCSR, + csr | MUSB_TXCSR_MODE); + + qh->segsize = min(len, dma_channel->max_len); + + if (qh->segsize <= packet_sz) + dma_channel->desired_mode = 0; + else + dma_channel->desired_mode = 1; + + + if (dma_channel->desired_mode == 0) { + csr &= ~(MUSB_TXCSR_AUTOSET + | MUSB_TXCSR_DMAMODE); + csr |= (MUSB_TXCSR_DMAENAB); + /* against programming guide */ + } else + csr |= (MUSB_TXCSR_AUTOSET + | MUSB_TXCSR_DMAENAB + | MUSB_TXCSR_DMAMODE); + + musb_writew(epio, MUSB_TXCSR, csr); + + dma_ok = dma_controller->channel_program( + dma_channel, packet_sz, + dma_channel->desired_mode, + urb->transfer_dma, + qh->segsize); + if (dma_ok) { + load_count = 0; + } else { + dma_controller->channel_release(dma_channel); + if (is_out) + hw_ep->tx_channel = NULL; + else + hw_ep->rx_channel = NULL; + dma_channel = NULL; + } + } +#endif + + /* candidate for DMA */ + if ((is_cppi_enabled() || tusb_dma_omap()) && dma_channel) { + + /* program endpoint CSRs first, then setup DMA. + * assume CPPI setup succeeds. + * defer enabling dma. + */ + csr = musb_readw(epio, MUSB_TXCSR); + csr &= ~(MUSB_TXCSR_AUTOSET + | MUSB_TXCSR_DMAMODE + | MUSB_TXCSR_DMAENAB); + csr |= MUSB_TXCSR_MODE; + musb_writew(epio, MUSB_TXCSR, + csr | MUSB_TXCSR_MODE); + + dma_channel->actual_len = 0L; + qh->segsize = len; + + /* TX uses "rndis" mode automatically, but needs help + * to identify the zero-length-final-packet case. + */ + dma_ok = dma_controller->channel_program( + dma_channel, packet_sz, + (urb->transfer_flags + & URB_ZERO_PACKET) + == URB_ZERO_PACKET, + urb->transfer_dma, + qh->segsize); + if (dma_ok) { + load_count = 0; + } else { + dma_controller->channel_release(dma_channel); + hw_ep->tx_channel = NULL; + dma_channel = NULL; + + /* REVISIT there's an error path here that + * needs handling: can't do dma, but + * there's no pio buffer address... + */ + } + } + + if (load_count) { + /* ASSERT: TXCSR_DMAENAB was already cleared */ + + /* PIO to load FIFO */ + qh->segsize = load_count; + musb_write_fifo(hw_ep, load_count, buf); + csr = musb_readw(epio, MUSB_TXCSR); + csr &= ~(MUSB_TXCSR_DMAENAB + | MUSB_TXCSR_DMAMODE + | MUSB_TXCSR_AUTOSET); + /* write CSR */ + csr |= MUSB_TXCSR_MODE; + + if (epnum) + musb_writew(epio, MUSB_TXCSR, csr); + } + + /* re-enable interrupt */ + musb_writew(mbase, MUSB_INTRTXE, int_txe); + + /* IN/receive */ + } else { + u16 csr; + + if (hw_ep->rx_reinit) { + musb_rx_reinit(musb, qh, hw_ep); + + /* init new state: toggle and NYET, maybe DMA later */ + if (usb_gettoggle(urb->dev, qh->epnum, 0)) + csr = MUSB_RXCSR_H_WR_DATATOGGLE + | MUSB_RXCSR_H_DATATOGGLE; + else + csr = 0; + if (qh->type == USB_ENDPOINT_XFER_INT) + csr |= MUSB_RXCSR_DISNYET; + + } else { + csr = musb_readw(hw_ep->regs, MUSB_RXCSR); + + if (csr & (MUSB_RXCSR_RXPKTRDY + | MUSB_RXCSR_DMAENAB + | MUSB_RXCSR_H_REQPKT)) + ERR("broken !rx_reinit, ep%d csr %04x\n", + hw_ep->epnum, csr); + + /* scrub any stale state, leaving toggle alone */ + csr &= MUSB_RXCSR_DISNYET; + } + + /* kick things off */ + + if ((is_cppi_enabled() || tusb_dma_omap()) && dma_channel) { + /* candidate for DMA */ + if (dma_channel) { + dma_channel->actual_len = 0L; + qh->segsize = len; + + /* AUTOREQ is in a DMA register */ + musb_writew(hw_ep->regs, MUSB_RXCSR, csr); + csr = musb_readw(hw_ep->regs, + MUSB_RXCSR); + + /* unless caller treats short rx transfers as + * errors, we dare not queue multiple transfers. + */ + dma_ok = dma_controller->channel_program( + dma_channel, packet_sz, + !(urb->transfer_flags + & URB_SHORT_NOT_OK), + urb->transfer_dma, + qh->segsize); + if (!dma_ok) { + dma_controller->channel_release( + dma_channel); + hw_ep->rx_channel = NULL; + dma_channel = NULL; + } else + csr |= MUSB_RXCSR_DMAENAB; + } + } + + csr |= MUSB_RXCSR_H_REQPKT; + DBG(7, "RXCSR%d := %04x\n", epnum, csr); + musb_writew(hw_ep->regs, MUSB_RXCSR, csr); + csr = musb_readw(hw_ep->regs, MUSB_RXCSR); + } +} + + +/* + * Service the default endpoint (ep0) as host. + * Return true until it's time to start the status stage. + */ +static bool musb_h_ep0_continue(struct musb *musb, u16 len, struct urb *urb) +{ + bool more = false; + u8 *fifo_dest = NULL; + u16 fifo_count = 0; + struct musb_hw_ep *hw_ep = musb->control_ep; + struct musb_qh *qh = hw_ep->in_qh; + struct usb_ctrlrequest *request; + + switch (musb->ep0_stage) { + case MUSB_EP0_IN: + fifo_dest = urb->transfer_buffer + urb->actual_length; + fifo_count = min(len, ((u16) (urb->transfer_buffer_length + - urb->actual_length))); + if (fifo_count < len) + urb->status = -EOVERFLOW; + + musb_read_fifo(hw_ep, fifo_count, fifo_dest); + + urb->actual_length += fifo_count; + if (len < qh->maxpacket) { + /* always terminate on short read; it's + * rarely reported as an error. + */ + } else if (urb->actual_length < + urb->transfer_buffer_length) + more = true; + break; + case MUSB_EP0_START: + request = (struct usb_ctrlrequest *) urb->setup_packet; + + if (!request->wLength) { + DBG(4, "start no-DATA\n"); + break; + } else if (request->bRequestType & USB_DIR_IN) { + DBG(4, "start IN-DATA\n"); + musb->ep0_stage = MUSB_EP0_IN; + more = true; + break; + } else { + DBG(4, "start OUT-DATA\n"); + musb->ep0_stage = MUSB_EP0_OUT; + more = true; + } + /* FALLTHROUGH */ + case MUSB_EP0_OUT: + fifo_count = min(qh->maxpacket, ((u16) + (urb->transfer_buffer_length + - urb->actual_length))); + + if (fifo_count) { + fifo_dest = (u8 *) (urb->transfer_buffer + + urb->actual_length); + DBG(3, "Sending %d bytes to %p\n", + fifo_count, fifo_dest); + musb_write_fifo(hw_ep, fifo_count, fifo_dest); + + urb->actual_length += fifo_count; + more = true; + } + break; + default: + ERR("bogus ep0 stage %d\n", musb->ep0_stage); + break; + } + + return more; +} + +/* + * Handle default endpoint interrupt as host. Only called in IRQ time + * from the LinuxIsr() interrupt service routine. + * + * called with controller irqlocked + */ +irqreturn_t musb_h_ep0_irq(struct musb *musb) +{ + struct urb *urb; + u16 csr, len; + int status = 0; + void __iomem *mbase = musb->mregs; + struct musb_hw_ep *hw_ep = musb->control_ep; + void __iomem *epio = hw_ep->regs; + struct musb_qh *qh = hw_ep->in_qh; + bool complete = false; + irqreturn_t retval = IRQ_NONE; + + /* ep0 only has one queue, "in" */ + urb = next_urb(qh); + + musb_ep_select(mbase, 0); + csr = musb_readw(epio, MUSB_CSR0); + len = (csr & MUSB_CSR0_RXPKTRDY) + ? musb_readb(epio, MUSB_COUNT0) + : 0; + + DBG(4, "<== csr0 %04x, qh %p, count %d, urb %p, stage %d\n", + csr, qh, len, urb, musb->ep0_stage); + + /* if we just did status stage, we are done */ + if (MUSB_EP0_STATUS == musb->ep0_stage) { + retval = IRQ_HANDLED; + complete = true; + } + + /* prepare status */ + if (csr & MUSB_CSR0_H_RXSTALL) { + DBG(6, "STALLING ENDPOINT\n"); + status = -EPIPE; + + } else if (csr & MUSB_CSR0_H_ERROR) { + DBG(2, "no response, csr0 %04x\n", csr); + status = -EPROTO; + + } else if (csr & MUSB_CSR0_H_NAKTIMEOUT) { + DBG(2, "control NAK timeout\n"); + + /* NOTE: this code path would be a good place to PAUSE a + * control transfer, if another one is queued, so that + * ep0 is more likely to stay busy. + * + * if (qh->ring.next != &musb->control), then + * we have a candidate... NAKing is *NOT* an error + */ + musb_writew(epio, MUSB_CSR0, 0); + retval = IRQ_HANDLED; + } + + if (status) { + DBG(6, "aborting\n"); + retval = IRQ_HANDLED; + if (urb) + urb->status = status; + complete = true; + + /* use the proper sequence to abort the transfer */ + if (csr & MUSB_CSR0_H_REQPKT) { + csr &= ~MUSB_CSR0_H_REQPKT; + musb_writew(epio, MUSB_CSR0, csr); + csr &= ~MUSB_CSR0_H_NAKTIMEOUT; + musb_writew(epio, MUSB_CSR0, csr); + } else { + csr |= MUSB_CSR0_FLUSHFIFO; + musb_writew(epio, MUSB_CSR0, csr); + musb_writew(epio, MUSB_CSR0, csr); + csr &= ~MUSB_CSR0_H_NAKTIMEOUT; + musb_writew(epio, MUSB_CSR0, csr); + } + + musb_writeb(epio, MUSB_NAKLIMIT0, 0); + + /* clear it */ + musb_writew(epio, MUSB_CSR0, 0); + } + + if (unlikely(!urb)) { + /* stop endpoint since we have no place for its data, this + * SHOULD NEVER HAPPEN! */ + ERR("no URB for end 0\n"); + + musb_writew(epio, MUSB_CSR0, MUSB_CSR0_FLUSHFIFO); + musb_writew(epio, MUSB_CSR0, MUSB_CSR0_FLUSHFIFO); + musb_writew(epio, MUSB_CSR0, 0); + + goto done; + } + + if (!complete) { + /* call common logic and prepare response */ + if (musb_h_ep0_continue(musb, len, urb)) { + /* more packets required */ + csr = (MUSB_EP0_IN == musb->ep0_stage) + ? MUSB_CSR0_H_REQPKT : MUSB_CSR0_TXPKTRDY; + } else { + /* data transfer complete; perform status phase */ + if (usb_pipeout(urb->pipe) + || !urb->transfer_buffer_length) + csr = MUSB_CSR0_H_STATUSPKT + | MUSB_CSR0_H_REQPKT; + else + csr = MUSB_CSR0_H_STATUSPKT + | MUSB_CSR0_TXPKTRDY; + + /* flag status stage */ + musb->ep0_stage = MUSB_EP0_STATUS; + + DBG(5, "ep0 STATUS, csr %04x\n", csr); + + } + musb_writew(epio, MUSB_CSR0, csr); + retval = IRQ_HANDLED; + } else + musb->ep0_stage = MUSB_EP0_IDLE; + + /* call completion handler if done */ + if (complete) + musb_advance_schedule(musb, urb, hw_ep, 1); +done: + return retval; +} + + +#ifdef CONFIG_USB_INVENTRA_DMA + +/* Host side TX (OUT) using Mentor DMA works as follows: + submit_urb -> + - if queue was empty, Program Endpoint + - ... which starts DMA to fifo in mode 1 or 0 + + DMA Isr (transfer complete) -> TxAvail() + - Stop DMA (~DmaEnab) (<--- Alert ... currently happens + only in musb_cleanup_urb) + - TxPktRdy has to be set in mode 0 or for + short packets in mode 1. +*/ + +#endif + +/* Service a Tx-Available or dma completion irq for the endpoint */ +void musb_host_tx(struct musb *musb, u8 epnum) +{ + int pipe; + bool done = false; + u16 tx_csr; + size_t wLength = 0; + u8 *buf = NULL; + struct urb *urb; + struct musb_hw_ep *hw_ep = musb->endpoints + epnum; + void __iomem *epio = hw_ep->regs; + struct musb_qh *qh = hw_ep->out_qh; + u32 status = 0; + void __iomem *mbase = musb->mregs; + struct dma_channel *dma; + + urb = next_urb(qh); + + musb_ep_select(mbase, epnum); + tx_csr = musb_readw(epio, MUSB_TXCSR); + + /* with CPPI, DMA sometimes triggers "extra" irqs */ + if (!urb) { + DBG(4, "extra TX%d ready, csr %04x\n", epnum, tx_csr); + goto finish; + } + + pipe = urb->pipe; + dma = is_dma_capable() ? hw_ep->tx_channel : NULL; + DBG(4, "OUT/TX%d end, csr %04x%s\n", epnum, tx_csr, + dma ? ", dma" : ""); + + /* check for errors */ + if (tx_csr & MUSB_TXCSR_H_RXSTALL) { + /* dma was disabled, fifo flushed */ + DBG(3, "TX end %d stall\n", epnum); + + /* stall; record URB status */ + status = -EPIPE; + + } else if (tx_csr & MUSB_TXCSR_H_ERROR) { + /* (NON-ISO) dma was disabled, fifo flushed */ + DBG(3, "TX 3strikes on ep=%d\n", epnum); + + status = -ETIMEDOUT; + + } else if (tx_csr & MUSB_TXCSR_H_NAKTIMEOUT) { + DBG(6, "TX end=%d device not responding\n", epnum); + + /* NOTE: this code path would be a good place to PAUSE a + * transfer, if there's some other (nonperiodic) tx urb + * that could use this fifo. (dma complicates it...) + * + * if (bulk && qh->ring.next != &musb->out_bulk), then + * we have a candidate... NAKing is *NOT* an error + */ + musb_ep_select(mbase, epnum); + musb_writew(epio, MUSB_TXCSR, + MUSB_TXCSR_H_WZC_BITS + | MUSB_TXCSR_TXPKTRDY); + goto finish; + } + + if (status) { + if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) { + dma->status = MUSB_DMA_STATUS_CORE_ABORT; + (void) musb->dma_controller->channel_abort(dma); + } + + /* do the proper sequence to abort the transfer in the + * usb core; the dma engine should already be stopped. + */ + musb_h_tx_flush_fifo(hw_ep); + tx_csr &= ~(MUSB_TXCSR_AUTOSET + | MUSB_TXCSR_DMAENAB + | MUSB_TXCSR_H_ERROR + | MUSB_TXCSR_H_RXSTALL + | MUSB_TXCSR_H_NAKTIMEOUT + ); + + musb_ep_select(mbase, epnum); + musb_writew(epio, MUSB_TXCSR, tx_csr); + /* REVISIT may need to clear FLUSHFIFO ... */ + musb_writew(epio, MUSB_TXCSR, tx_csr); + musb_writeb(epio, MUSB_TXINTERVAL, 0); + + done = true; + } + + /* second cppi case */ + if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) { + DBG(4, "extra TX%d ready, csr %04x\n", epnum, tx_csr); + goto finish; + + } + + /* REVISIT this looks wrong... */ + if (!status || dma || usb_pipeisoc(pipe)) { + if (dma) + wLength = dma->actual_len; + else + wLength = qh->segsize; + qh->offset += wLength; + + if (usb_pipeisoc(pipe)) { + struct usb_iso_packet_descriptor *d; + + d = urb->iso_frame_desc + qh->iso_idx; + d->actual_length = qh->segsize; + if (++qh->iso_idx >= urb->number_of_packets) { + done = true; + } else { + d++; + buf = urb->transfer_buffer + d->offset; + wLength = d->length; + } + } else if (dma) { + done = true; + } else { + /* see if we need to send more data, or ZLP */ + if (qh->segsize < qh->maxpacket) + done = true; + else if (qh->offset == urb->transfer_buffer_length + && !(urb->transfer_flags + & URB_ZERO_PACKET)) + done = true; + if (!done) { + buf = urb->transfer_buffer + + qh->offset; + wLength = urb->transfer_buffer_length + - qh->offset; + } + } + } + + /* urb->status != -EINPROGRESS means request has been faulted, + * so we must abort this transfer after cleanup + */ + if (urb->status != -EINPROGRESS) { + done = true; + if (status == 0) + status = urb->status; + } + + if (done) { + /* set status */ + urb->status = status; + urb->actual_length = qh->offset; + musb_advance_schedule(musb, urb, hw_ep, USB_DIR_OUT); + + } else if (!(tx_csr & MUSB_TXCSR_DMAENAB)) { + /* WARN_ON(!buf); */ + + /* REVISIT: some docs say that when hw_ep->tx_double_buffered, + * (and presumably, fifo is not half-full) we should write TWO + * packets before updating TXCSR ... other docs disagree ... + */ + /* PIO: start next packet in this URB */ + wLength = min(qh->maxpacket, (u16) wLength); + musb_write_fifo(hw_ep, wLength, buf); + qh->segsize = wLength; + + musb_ep_select(mbase, epnum); + musb_writew(epio, MUSB_TXCSR, + MUSB_TXCSR_H_WZC_BITS | MUSB_TXCSR_TXPKTRDY); + } else + DBG(1, "not complete, but dma enabled?\n"); + +finish: + return; +} + + +#ifdef CONFIG_USB_INVENTRA_DMA + +/* Host side RX (IN) using Mentor DMA works as follows: + submit_urb -> + - if queue was empty, ProgramEndpoint + - first IN token is sent out (by setting ReqPkt) + LinuxIsr -> RxReady() + /\ => first packet is received + | - Set in mode 0 (DmaEnab, ~ReqPkt) + | -> DMA Isr (transfer complete) -> RxReady() + | - Ack receive (~RxPktRdy), turn off DMA (~DmaEnab) + | - if urb not complete, send next IN token (ReqPkt) + | | else complete urb. + | | + --------------------------- + * + * Nuances of mode 1: + * For short packets, no ack (+RxPktRdy) is sent automatically + * (even if AutoClear is ON) + * For full packets, ack (~RxPktRdy) and next IN token (+ReqPkt) is sent + * automatically => major problem, as collecting the next packet becomes + * difficult. Hence mode 1 is not used. + * + * REVISIT + * All we care about at this driver level is that + * (a) all URBs terminate with REQPKT cleared and fifo(s) empty; + * (b) termination conditions are: short RX, or buffer full; + * (c) fault modes include + * - iff URB_SHORT_NOT_OK, short RX status is -EREMOTEIO. + * (and that endpoint's dma queue stops immediately) + * - overflow (full, PLUS more bytes in the terminal packet) + * + * So for example, usb-storage sets URB_SHORT_NOT_OK, and would + * thus be a great candidate for using mode 1 ... for all but the + * last packet of one URB's transfer. + */ + +#endif + +/* + * Service an RX interrupt for the given IN endpoint; docs cover bulk, iso, + * and high-bandwidth IN transfer cases. + */ +void musb_host_rx(struct musb *musb, u8 epnum) +{ + struct urb *urb; + struct musb_hw_ep *hw_ep = musb->endpoints + epnum; + void __iomem *epio = hw_ep->regs; + struct musb_qh *qh = hw_ep->in_qh; + size_t xfer_len; + void __iomem *mbase = musb->mregs; + int pipe; + u16 rx_csr, val; + bool iso_err = false; + bool done = false; + u32 status; + struct dma_channel *dma; + + musb_ep_select(mbase, epnum); + + urb = next_urb(qh); + dma = is_dma_capable() ? hw_ep->rx_channel : NULL; + status = 0; + xfer_len = 0; + + rx_csr = musb_readw(epio, MUSB_RXCSR); + val = rx_csr; + + if (unlikely(!urb)) { + /* REVISIT -- THIS SHOULD NEVER HAPPEN ... but, at least + * usbtest #11 (unlinks) triggers it regularly, sometimes + * with fifo full. (Only with DMA??) + */ + DBG(3, "BOGUS RX%d ready, csr %04x, count %d\n", epnum, val, + musb_readw(epio, MUSB_RXCOUNT)); + musb_h_flush_rxfifo(hw_ep, MUSB_RXCSR_CLRDATATOG); + return; + } + + pipe = urb->pipe; + + DBG(5, "<== hw %d rxcsr %04x, urb actual %d (+dma %zu)\n", + epnum, rx_csr, urb->actual_length, + dma ? dma->actual_len : 0); + + /* check for errors, concurrent stall & unlink is not really + * handled yet! */ + if (rx_csr & MUSB_RXCSR_H_RXSTALL) { + DBG(3, "RX end %d STALL\n", epnum); + + /* stall; record URB status */ + status = -EPIPE; + + } else if (rx_csr & MUSB_RXCSR_H_ERROR) { + DBG(3, "end %d RX proto error\n", epnum); + + status = -EPROTO; + musb_writeb(epio, MUSB_RXINTERVAL, 0); + + } else if (rx_csr & MUSB_RXCSR_DATAERROR) { + + if (USB_ENDPOINT_XFER_ISOC != qh->type) { + /* NOTE this code path would be a good place to PAUSE a + * transfer, if there's some other (nonperiodic) rx urb + * that could use this fifo. (dma complicates it...) + * + * if (bulk && qh->ring.next != &musb->in_bulk), then + * we have a candidate... NAKing is *NOT* an error + */ + DBG(6, "RX end %d NAK timeout\n", epnum); + musb_ep_select(mbase, epnum); + musb_writew(epio, MUSB_RXCSR, + MUSB_RXCSR_H_WZC_BITS + | MUSB_RXCSR_H_REQPKT); + + goto finish; + } else { + DBG(4, "RX end %d ISO data error\n", epnum); + /* packet error reported later */ + iso_err = true; + } + } + + /* faults abort the transfer */ + if (status) { + /* clean up dma and collect transfer count */ + if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) { + dma->status = MUSB_DMA_STATUS_CORE_ABORT; + (void) musb->dma_controller->channel_abort(dma); + xfer_len = dma->actual_len; + } + musb_h_flush_rxfifo(hw_ep, MUSB_RXCSR_CLRDATATOG); + musb_writeb(epio, MUSB_RXINTERVAL, 0); + done = true; + goto finish; + } + + if (unlikely(dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY)) { + /* SHOULD NEVER HAPPEN ... but at least DaVinci has done it */ + ERR("RX%d dma busy, csr %04x\n", epnum, rx_csr); + goto finish; + } + + /* thorough shutdown for now ... given more precise fault handling + * and better queueing support, we might keep a DMA pipeline going + * while processing this irq for earlier completions. + */ + + /* FIXME this is _way_ too much in-line logic for Mentor DMA */ + +#ifndef CONFIG_USB_INVENTRA_DMA + if (rx_csr & MUSB_RXCSR_H_REQPKT) { + /* REVISIT this happened for a while on some short reads... + * the cleanup still needs investigation... looks bad... + * and also duplicates dma cleanup code above ... plus, + * shouldn't this be the "half full" double buffer case? + */ + if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) { + dma->status = MUSB_DMA_STATUS_CORE_ABORT; + (void) musb->dma_controller->channel_abort(dma); + xfer_len = dma->actual_len; + done = true; + } + + DBG(2, "RXCSR%d %04x, reqpkt, len %zu%s\n", epnum, rx_csr, + xfer_len, dma ? ", dma" : ""); + rx_csr &= ~MUSB_RXCSR_H_REQPKT; + + musb_ep_select(mbase, epnum); + musb_writew(epio, MUSB_RXCSR, + MUSB_RXCSR_H_WZC_BITS | rx_csr); + } +#endif + if (dma && (rx_csr & MUSB_RXCSR_DMAENAB)) { + xfer_len = dma->actual_len; + + val &= ~(MUSB_RXCSR_DMAENAB + | MUSB_RXCSR_H_AUTOREQ + | MUSB_RXCSR_AUTOCLEAR + | MUSB_RXCSR_RXPKTRDY); + musb_writew(hw_ep->regs, MUSB_RXCSR, val); + +#ifdef CONFIG_USB_INVENTRA_DMA + /* done if urb buffer is full or short packet is recd */ + done = (urb->actual_length + xfer_len >= + urb->transfer_buffer_length + || dma->actual_len < qh->maxpacket); + + /* send IN token for next packet, without AUTOREQ */ + if (!done) { + val |= MUSB_RXCSR_H_REQPKT; + musb_writew(epio, MUSB_RXCSR, + MUSB_RXCSR_H_WZC_BITS | val); + } + + DBG(4, "ep %d dma %s, rxcsr %04x, rxcount %d\n", epnum, + done ? "off" : "reset", + musb_readw(epio, MUSB_RXCSR), + musb_readw(epio, MUSB_RXCOUNT)); +#else + done = true; +#endif + } else if (urb->status == -EINPROGRESS) { + /* if no errors, be sure a packet is ready for unloading */ + if (unlikely(!(rx_csr & MUSB_RXCSR_RXPKTRDY))) { + status = -EPROTO; + ERR("Rx interrupt with no errors or packet!\n"); + + /* FIXME this is another "SHOULD NEVER HAPPEN" */ + +/* SCRUB (RX) */ + /* do the proper sequence to abort the transfer */ + musb_ep_select(mbase, epnum); + val &= ~MUSB_RXCSR_H_REQPKT; + musb_writew(epio, MUSB_RXCSR, val); + goto finish; + } + + /* we are expecting IN packets */ +#ifdef CONFIG_USB_INVENTRA_DMA + if (dma) { + struct dma_controller *c; + u16 rx_count; + int ret; + + rx_count = musb_readw(epio, MUSB_RXCOUNT); + + DBG(2, "RX%d count %d, buffer 0x%x len %d/%d\n", + epnum, rx_count, + urb->transfer_dma + + urb->actual_length, + qh->offset, + urb->transfer_buffer_length); + + c = musb->dma_controller; + + dma->desired_mode = 0; +#ifdef USE_MODE1 + /* because of the issue below, mode 1 will + * only rarely behave with correct semantics. + */ + if ((urb->transfer_flags & + URB_SHORT_NOT_OK) + && (urb->transfer_buffer_length - + urb->actual_length) + > qh->maxpacket) + dma->desired_mode = 1; +#endif + +/* Disadvantage of using mode 1: + * It's basically usable only for mass storage class; essentially all + * other protocols also terminate transfers on short packets. + * + * Details: + * An extra IN token is sent at the end of the transfer (due to AUTOREQ) + * If you try to use mode 1 for (transfer_buffer_length - 512), and try + * to use the extra IN token to grab the last packet using mode 0, then + * the problem is that you cannot be sure when the device will send the + * last packet and RxPktRdy set. Sometimes the packet is recd too soon + * such that it gets lost when RxCSR is re-set at the end of the mode 1 + * transfer, while sometimes it is recd just a little late so that if you + * try to configure for mode 0 soon after the mode 1 transfer is + * completed, you will find rxcount 0. Okay, so you might think why not + * wait for an interrupt when the pkt is recd. Well, you won't get any! + */ + + val = musb_readw(epio, MUSB_RXCSR); + val &= ~MUSB_RXCSR_H_REQPKT; + + if (dma->desired_mode == 0) + val &= ~MUSB_RXCSR_H_AUTOREQ; + else + val |= MUSB_RXCSR_H_AUTOREQ; + val |= MUSB_RXCSR_AUTOCLEAR | MUSB_RXCSR_DMAENAB; + + musb_writew(epio, MUSB_RXCSR, + MUSB_RXCSR_H_WZC_BITS | val); + + /* REVISIT if when actual_length != 0, + * transfer_buffer_length needs to be + * adjusted first... + */ + ret = c->channel_program( + dma, qh->maxpacket, + dma->desired_mode, + urb->transfer_dma + + urb->actual_length, + (dma->desired_mode == 0) + ? rx_count + : urb->transfer_buffer_length); + + if (!ret) { + c->channel_release(dma); + hw_ep->rx_channel = NULL; + dma = NULL; + /* REVISIT reset CSR */ + } + } +#endif /* Mentor DMA */ + + if (!dma) { + done = musb_host_packet_rx(musb, urb, + epnum, iso_err); + DBG(6, "read %spacket\n", done ? "last " : ""); + } + } + + if (dma && usb_pipeisoc(pipe)) { + struct usb_iso_packet_descriptor *d; + int iso_stat = status; + + d = urb->iso_frame_desc + qh->iso_idx; + d->actual_length += xfer_len; + if (iso_err) { + iso_stat = -EILSEQ; + urb->error_count++; + } + d->status = iso_stat; + } + +finish: + urb->actual_length += xfer_len; + qh->offset += xfer_len; + if (done) { + if (urb->status == -EINPROGRESS) + urb->status = status; + musb_advance_schedule(musb, urb, hw_ep, USB_DIR_IN); + } +} + +/* schedule nodes correspond to peripheral endpoints, like an OHCI QH. + * the software schedule associates multiple such nodes with a given + * host side hardware endpoint + direction; scheduling may activate + * that hardware endpoint. + */ +static int musb_schedule( + struct musb *musb, + struct musb_qh *qh, + int is_in) +{ + int idle; + int best_diff; + int best_end, epnum; + struct musb_hw_ep *hw_ep = NULL; + struct list_head *head = NULL; + + /* use fixed hardware for control and bulk */ + switch (qh->type) { + case USB_ENDPOINT_XFER_CONTROL: + head = &musb->control; + hw_ep = musb->control_ep; + break; + case USB_ENDPOINT_XFER_BULK: + hw_ep = musb->bulk_ep; + if (is_in) + head = &musb->in_bulk; + else + head = &musb->out_bulk; + break; + } + if (head) { + idle = list_empty(head); + list_add_tail(&qh->ring, head); + goto success; + } + + /* else, periodic transfers get muxed to other endpoints */ + + /* FIXME this doesn't consider direction, so it can only + * work for one half of the endpoint hardware, and assumes + * the previous cases handled all non-shared endpoints... + */ + + /* we know this qh hasn't been scheduled, so all we need to do + * is choose which hardware endpoint to put it on ... + * + * REVISIT what we really want here is a regular schedule tree + * like e.g. OHCI uses, but for now musb->periodic is just an + * array of the _single_ logical endpoint associated with a + * given physical one (identity mapping logical->physical). + * + * that simplistic approach makes TT scheduling a lot simpler; + * there is none, and thus none of its complexity... + */ + best_diff = 4096; + best_end = -1; + + for (epnum = 1; epnum < musb->nr_endpoints; epnum++) { + int diff; + + if (musb->periodic[epnum]) + continue; + hw_ep = &musb->endpoints[epnum]; + if (hw_ep == musb->bulk_ep) + continue; + + if (is_in) + diff = hw_ep->max_packet_sz_rx - qh->maxpacket; + else + diff = hw_ep->max_packet_sz_tx - qh->maxpacket; + + if (diff > 0 && best_diff > diff) { + best_diff = diff; + best_end = epnum; + } + } + if (best_end < 0) + return -ENOSPC; + + idle = 1; + hw_ep = musb->endpoints + best_end; + musb->periodic[best_end] = qh; + DBG(4, "qh %p periodic slot %d\n", qh, best_end); +success: + qh->hw_ep = hw_ep; + qh->hep->hcpriv = qh; + if (idle) + musb_start_urb(musb, is_in, qh); + return 0; +} + +static int musb_urb_enqueue( + struct usb_hcd *hcd, + struct urb *urb, + gfp_t mem_flags) +{ + unsigned long flags; + struct musb *musb = hcd_to_musb(hcd); + struct usb_host_endpoint *hep = urb->ep; + struct musb_qh *qh = hep->hcpriv; + struct usb_endpoint_descriptor *epd = &hep->desc; + int ret; + unsigned type_reg; + unsigned interval; + + /* host role must be active */ + if (!is_host_active(musb) || !musb->is_active) + return -ENODEV; + + spin_lock_irqsave(&musb->lock, flags); + ret = usb_hcd_link_urb_to_ep(hcd, urb); + spin_unlock_irqrestore(&musb->lock, flags); + if (ret) + return ret; + + /* DMA mapping was already done, if needed, and this urb is on + * hep->urb_list ... so there's little to do unless hep wasn't + * yet scheduled onto a live qh. + * + * REVISIT best to keep hep->hcpriv valid until the endpoint gets + * disabled, testing for empty qh->ring and avoiding qh setup costs + * except for the first urb queued after a config change. + */ + if (qh) { + urb->hcpriv = qh; + return 0; + } + + /* Allocate and initialize qh, minimizing the work done each time + * hw_ep gets reprogrammed, or with irqs blocked. Then schedule it. + * + * REVISIT consider a dedicated qh kmem_cache, so it's harder + * for bugs in other kernel code to break this driver... + */ + qh = kzalloc(sizeof *qh, mem_flags); + if (!qh) { + usb_hcd_unlink_urb_from_ep(hcd, urb); + return -ENOMEM; + } + + qh->hep = hep; + qh->dev = urb->dev; + INIT_LIST_HEAD(&qh->ring); + qh->is_ready = 1; + + qh->maxpacket = le16_to_cpu(epd->wMaxPacketSize); + + /* no high bandwidth support yet */ + if (qh->maxpacket & ~0x7ff) { + ret = -EMSGSIZE; + goto done; + } + + qh->epnum = epd->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK; + qh->type = epd->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK; + + /* NOTE: urb->dev->devnum is wrong during SET_ADDRESS */ + qh->addr_reg = (u8) usb_pipedevice(urb->pipe); + + /* precompute rxtype/txtype/type0 register */ + type_reg = (qh->type << 4) | qh->epnum; + switch (urb->dev->speed) { + case USB_SPEED_LOW: + type_reg |= 0xc0; + break; + case USB_SPEED_FULL: + type_reg |= 0x80; + break; + default: + type_reg |= 0x40; + } + qh->type_reg = type_reg; + + /* precompute rxinterval/txinterval register */ + interval = min((u8)16, epd->bInterval); /* log encoding */ + switch (qh->type) { + case USB_ENDPOINT_XFER_INT: + /* fullspeed uses linear encoding */ + if (USB_SPEED_FULL == urb->dev->speed) { + interval = epd->bInterval; + if (!interval) + interval = 1; + } + /* FALLTHROUGH */ + case USB_ENDPOINT_XFER_ISOC: + /* iso always uses log encoding */ + break; + default: + /* REVISIT we actually want to use NAK limits, hinting to the + * transfer scheduling logic to try some other qh, e.g. try + * for 2 msec first: + * + * interval = (USB_SPEED_HIGH == urb->dev->speed) ? 16 : 2; + * + * The downside of disabling this is that transfer scheduling + * gets VERY unfair for nonperiodic transfers; a misbehaving + * peripheral could make that hurt. Or for reads, one that's + * perfectly normal: network and other drivers keep reads + * posted at all times, having one pending for a week should + * be perfectly safe. + * + * The upside of disabling it is avoidng transfer scheduling + * code to put this aside for while. + */ + interval = 0; + } + qh->intv_reg = interval; + + /* precompute addressing for external hub/tt ports */ + if (musb->is_multipoint) { + struct usb_device *parent = urb->dev->parent; + + if (parent != hcd->self.root_hub) { + qh->h_addr_reg = (u8) parent->devnum; + + /* set up tt info if needed */ + if (urb->dev->tt) { + qh->h_port_reg = (u8) urb->dev->ttport; + qh->h_addr_reg |= 0x80; + } + } + } + + /* invariant: hep->hcpriv is null OR the qh that's already scheduled. + * until we get real dma queues (with an entry for each urb/buffer), + * we only have work to do in the former case. + */ + spin_lock_irqsave(&musb->lock, flags); + if (hep->hcpriv) { + /* some concurrent activity submitted another urb to hep... + * odd, rare, error prone, but legal. + */ + kfree(qh); + ret = 0; + } else + ret = musb_schedule(musb, qh, + epd->bEndpointAddress & USB_ENDPOINT_DIR_MASK); + + if (ret == 0) { + urb->hcpriv = qh; + /* FIXME set urb->start_frame for iso/intr, it's tested in + * musb_start_urb(), but otherwise only konicawc cares ... + */ + } + spin_unlock_irqrestore(&musb->lock, flags); + +done: + if (ret != 0) { + usb_hcd_unlink_urb_from_ep(hcd, urb); + kfree(qh); + } + return ret; +} + + +/* + * abort a transfer that's at the head of a hardware queue. + * called with controller locked, irqs blocked + * that hardware queue advances to the next transfer, unless prevented + */ +static int musb_cleanup_urb(struct urb *urb, struct musb_qh *qh, int is_in) +{ + struct musb_hw_ep *ep = qh->hw_ep; + void __iomem *epio = ep->regs; + unsigned hw_end = ep->epnum; + void __iomem *regs = ep->musb->mregs; + u16 csr; + int status = 0; + + musb_ep_select(regs, hw_end); + + if (is_dma_capable()) { + struct dma_channel *dma; + + dma = is_in ? ep->rx_channel : ep->tx_channel; + if (dma) { + status = ep->musb->dma_controller->channel_abort(dma); + DBG(status ? 1 : 3, + "abort %cX%d DMA for urb %p --> %d\n", + is_in ? 'R' : 'T', ep->epnum, + urb, status); + urb->actual_length += dma->actual_len; + } + } + + /* turn off DMA requests, discard state, stop polling ... */ + if (is_in) { + /* giveback saves bulk toggle */ + csr = musb_h_flush_rxfifo(ep, 0); + + /* REVISIT we still get an irq; should likely clear the + * endpoint's irq status here to avoid bogus irqs. + * clearing that status is platform-specific... + */ + } else { + musb_h_tx_flush_fifo(ep); + csr = musb_readw(epio, MUSB_TXCSR); + csr &= ~(MUSB_TXCSR_AUTOSET + | MUSB_TXCSR_DMAENAB + | MUSB_TXCSR_H_RXSTALL + | MUSB_TXCSR_H_NAKTIMEOUT + | MUSB_TXCSR_H_ERROR + | MUSB_TXCSR_TXPKTRDY); + musb_writew(epio, MUSB_TXCSR, csr); + /* REVISIT may need to clear FLUSHFIFO ... */ + musb_writew(epio, MUSB_TXCSR, csr); + /* flush cpu writebuffer */ + csr = musb_readw(epio, MUSB_TXCSR); + } + if (status == 0) + musb_advance_schedule(ep->musb, urb, ep, is_in); + return status; +} + +static int musb_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status) +{ + struct musb *musb = hcd_to_musb(hcd); + struct musb_qh *qh; + struct list_head *sched; + unsigned long flags; + int ret; + + DBG(4, "urb=%p, dev%d ep%d%s\n", urb, + usb_pipedevice(urb->pipe), + usb_pipeendpoint(urb->pipe), + usb_pipein(urb->pipe) ? "in" : "out"); + + spin_lock_irqsave(&musb->lock, flags); + ret = usb_hcd_check_unlink_urb(hcd, urb, status); + if (ret) + goto done; + + qh = urb->hcpriv; + if (!qh) + goto done; + + /* Any URB not actively programmed into endpoint hardware can be + * immediately given back. Such an URB must be at the head of its + * endpoint queue, unless someday we get real DMA queues. And even + * then, it might not be known to the hardware... + * + * Otherwise abort current transfer, pending dma, etc.; urb->status + * has already been updated. This is a synchronous abort; it'd be + * OK to hold off until after some IRQ, though. + */ + if (!qh->is_ready || urb->urb_list.prev != &qh->hep->urb_list) + ret = -EINPROGRESS; + else { + switch (qh->type) { + case USB_ENDPOINT_XFER_CONTROL: + sched = &musb->control; + break; + case USB_ENDPOINT_XFER_BULK: + if (usb_pipein(urb->pipe)) + sched = &musb->in_bulk; + else + sched = &musb->out_bulk; + break; + default: + /* REVISIT when we get a schedule tree, periodic + * transfers won't always be at the head of a + * singleton queue... + */ + sched = NULL; + break; + } + } + + /* NOTE: qh is invalid unless !list_empty(&hep->urb_list) */ + if (ret < 0 || (sched && qh != first_qh(sched))) { + int ready = qh->is_ready; + + ret = 0; + qh->is_ready = 0; + __musb_giveback(musb, urb, 0); + qh->is_ready = ready; + } else + ret = musb_cleanup_urb(urb, qh, urb->pipe & USB_DIR_IN); +done: + spin_unlock_irqrestore(&musb->lock, flags); + return ret; +} + +/* disable an endpoint */ +static void +musb_h_disable(struct usb_hcd *hcd, struct usb_host_endpoint *hep) +{ + u8 epnum = hep->desc.bEndpointAddress; + unsigned long flags; + struct musb *musb = hcd_to_musb(hcd); + u8 is_in = epnum & USB_DIR_IN; + struct musb_qh *qh = hep->hcpriv; + struct urb *urb, *tmp; + struct list_head *sched; + + if (!qh) + return; + + spin_lock_irqsave(&musb->lock, flags); + + switch (qh->type) { + case USB_ENDPOINT_XFER_CONTROL: + sched = &musb->control; + break; + case USB_ENDPOINT_XFER_BULK: + if (is_in) + sched = &musb->in_bulk; + else + sched = &musb->out_bulk; + break; + default: + /* REVISIT when we get a schedule tree, periodic transfers + * won't always be at the head of a singleton queue... + */ + sched = NULL; + break; + } + + /* NOTE: qh is invalid unless !list_empty(&hep->urb_list) */ + + /* kick first urb off the hardware, if needed */ + qh->is_ready = 0; + if (!sched || qh == first_qh(sched)) { + urb = next_urb(qh); + + /* make software (then hardware) stop ASAP */ + if (!urb->unlinked) + urb->status = -ESHUTDOWN; + + /* cleanup */ + musb_cleanup_urb(urb, qh, urb->pipe & USB_DIR_IN); + } else + urb = NULL; + + /* then just nuke all the others */ + list_for_each_entry_safe_from(urb, tmp, &hep->urb_list, urb_list) + musb_giveback(qh, urb, -ESHUTDOWN); + + spin_unlock_irqrestore(&musb->lock, flags); +} + +static int musb_h_get_frame_number(struct usb_hcd *hcd) +{ + struct musb *musb = hcd_to_musb(hcd); + + return musb_readw(musb->mregs, MUSB_FRAME); +} + +static int musb_h_start(struct usb_hcd *hcd) +{ + struct musb *musb = hcd_to_musb(hcd); + + /* NOTE: musb_start() is called when the hub driver turns + * on port power, or when (OTG) peripheral starts. + */ + hcd->state = HC_STATE_RUNNING; + musb->port1_status = 0; + return 0; +} + +static void musb_h_stop(struct usb_hcd *hcd) +{ + musb_stop(hcd_to_musb(hcd)); + hcd->state = HC_STATE_HALT; +} + +static int musb_bus_suspend(struct usb_hcd *hcd) +{ + struct musb *musb = hcd_to_musb(hcd); + + if (musb->xceiv.state == OTG_STATE_A_SUSPEND) + return 0; + + if (is_host_active(musb) && musb->is_active) { + WARNING("trying to suspend as %s is_active=%i\n", + otg_state_string(musb), musb->is_active); + return -EBUSY; + } else + return 0; +} + +static int musb_bus_resume(struct usb_hcd *hcd) +{ + /* resuming child port does the work */ + return 0; +} + +const struct hc_driver musb_hc_driver = { + .description = "musb-hcd", + .product_desc = "MUSB HDRC host driver", + .hcd_priv_size = sizeof(struct musb), + .flags = HCD_USB2 | HCD_MEMORY, + + /* not using irq handler or reset hooks from usbcore, since + * those must be shared with peripheral code for OTG configs + */ + + .start = musb_h_start, + .stop = musb_h_stop, + + .get_frame_number = musb_h_get_frame_number, + + .urb_enqueue = musb_urb_enqueue, + .urb_dequeue = musb_urb_dequeue, + .endpoint_disable = musb_h_disable, + + .hub_status_data = musb_hub_status_data, + .hub_control = musb_hub_control, + .bus_suspend = musb_bus_suspend, + .bus_resume = musb_bus_resume, + /* .start_port_reset = NULL, */ + /* .hub_irq_enable = NULL, */ +}; diff --git a/drivers/usb/musb/musb_host.h b/drivers/usb/musb/musb_host.h new file mode 100644 index 00000000000..77bcdb9d5b3 --- /dev/null +++ b/drivers/usb/musb/musb_host.h @@ -0,0 +1,110 @@ +/* + * MUSB OTG driver host defines + * + * Copyright 2005 Mentor Graphics Corporation + * Copyright (C) 2005-2006 by Texas Instruments + * Copyright (C) 2006-2007 Nokia Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + */ + +#ifndef _MUSB_HOST_H +#define _MUSB_HOST_H + +static inline struct usb_hcd *musb_to_hcd(struct musb *musb) +{ + return container_of((void *) musb, struct usb_hcd, hcd_priv); +} + +static inline struct musb *hcd_to_musb(struct usb_hcd *hcd) +{ + return (struct musb *) (hcd->hcd_priv); +} + +/* stored in "usb_host_endpoint.hcpriv" for scheduled endpoints */ +struct musb_qh { + struct usb_host_endpoint *hep; /* usbcore info */ + struct usb_device *dev; + struct musb_hw_ep *hw_ep; /* current binding */ + + struct list_head ring; /* of musb_qh */ + /* struct musb_qh *next; */ /* for periodic tree */ + + unsigned offset; /* in urb->transfer_buffer */ + unsigned segsize; /* current xfer fragment */ + + u8 type_reg; /* {rx,tx} type register */ + u8 intv_reg; /* {rx,tx} interval register */ + u8 addr_reg; /* device address register */ + u8 h_addr_reg; /* hub address register */ + u8 h_port_reg; /* hub port register */ + + u8 is_ready; /* safe to modify hw_ep */ + u8 type; /* XFERTYPE_* */ + u8 epnum; + u16 maxpacket; + u16 frame; /* for periodic schedule */ + unsigned iso_idx; /* in urb->iso_frame_desc[] */ +}; + +/* map from control or bulk queue head to the first qh on that ring */ +static inline struct musb_qh *first_qh(struct list_head *q) +{ + if (list_empty(q)) + return NULL; + return list_entry(q->next, struct musb_qh, ring); +} + + +extern void musb_root_disconnect(struct musb *musb); + +struct usb_hcd; + +extern int musb_hub_status_data(struct usb_hcd *hcd, char *buf); +extern int musb_hub_control(struct usb_hcd *hcd, + u16 typeReq, u16 wValue, u16 wIndex, + char *buf, u16 wLength); + +extern const struct hc_driver musb_hc_driver; + +static inline struct urb *next_urb(struct musb_qh *qh) +{ +#ifdef CONFIG_USB_MUSB_HDRC_HCD + struct list_head *queue; + + if (!qh) + return NULL; + queue = &qh->hep->urb_list; + if (list_empty(queue)) + return NULL; + return list_entry(queue->next, struct urb, urb_list); +#else + return NULL; +#endif +} + +#endif /* _MUSB_HOST_H */ diff --git a/drivers/usb/musb/musb_io.h b/drivers/usb/musb/musb_io.h new file mode 100644 index 00000000000..6bbedae83af --- /dev/null +++ b/drivers/usb/musb/musb_io.h @@ -0,0 +1,115 @@ +/* + * MUSB OTG driver register I/O + * + * Copyright 2005 Mentor Graphics Corporation + * Copyright (C) 2005-2006 by Texas Instruments + * Copyright (C) 2006-2007 Nokia Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + */ + +#ifndef __MUSB_LINUX_PLATFORM_ARCH_H__ +#define __MUSB_LINUX_PLATFORM_ARCH_H__ + +#include + +#ifndef CONFIG_ARM +static inline void readsl(const void __iomem *addr, void *buf, int len) + { insl((unsigned long)addr, buf, len); } +static inline void readsw(const void __iomem *addr, void *buf, int len) + { insw((unsigned long)addr, buf, len); } +static inline void readsb(const void __iomem *addr, void *buf, int len) + { insb((unsigned long)addr, buf, len); } + +static inline void writesl(const void __iomem *addr, const void *buf, int len) + { outsl((unsigned long)addr, buf, len); } +static inline void writesw(const void __iomem *addr, const void *buf, int len) + { outsw((unsigned long)addr, buf, len); } +static inline void writesb(const void __iomem *addr, const void *buf, int len) + { outsb((unsigned long)addr, buf, len); } + +#endif + +/* NOTE: these offsets are all in bytes */ + +static inline u16 musb_readw(const void __iomem *addr, unsigned offset) + { return __raw_readw(addr + offset); } + +static inline u32 musb_readl(const void __iomem *addr, unsigned offset) + { return __raw_readl(addr + offset); } + + +static inline void musb_writew(void __iomem *addr, unsigned offset, u16 data) + { __raw_writew(data, addr + offset); } + +static inline void musb_writel(void __iomem *addr, unsigned offset, u32 data) + { __raw_writel(data, addr + offset); } + + +#ifdef CONFIG_USB_TUSB6010 + +/* + * TUSB6010 doesn't allow 8-bit access; 16-bit access is the minimum. + */ +static inline u8 musb_readb(const void __iomem *addr, unsigned offset) +{ + u16 tmp; + u8 val; + + tmp = __raw_readw(addr + (offset & ~1)); + if (offset & 1) + val = (tmp >> 8); + else + val = tmp & 0xff; + + return val; +} + +static inline void musb_writeb(void __iomem *addr, unsigned offset, u8 data) +{ + u16 tmp; + + tmp = __raw_readw(addr + (offset & ~1)); + if (offset & 1) + tmp = (data << 8) | (tmp & 0xff); + else + tmp = (tmp & 0xff00) | data; + + __raw_writew(tmp, addr + (offset & ~1)); +} + +#else + +static inline u8 musb_readb(const void __iomem *addr, unsigned offset) + { return __raw_readb(addr + offset); } + +static inline void musb_writeb(void __iomem *addr, unsigned offset, u8 data) + { __raw_writeb(data, addr + offset); } + +#endif /* CONFIG_USB_TUSB6010 */ + +#endif diff --git a/drivers/usb/musb/musb_procfs.c b/drivers/usb/musb/musb_procfs.c new file mode 100644 index 00000000000..55e6b78bdcc --- /dev/null +++ b/drivers/usb/musb/musb_procfs.c @@ -0,0 +1,830 @@ +/* + * MUSB OTG driver debug support + * + * Copyright 2005 Mentor Graphics Corporation + * Copyright (C) 2005-2006 by Texas Instruments + * Copyright (C) 2006-2007 Nokia Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + */ + +#include +#include +#include +#include /* FIXME remove procfs writes */ +#include + +#include "musb_core.h" + +#include "davinci.h" + +#ifdef CONFIG_USB_MUSB_HDRC_HCD + +static int dump_qh(struct musb_qh *qh, char *buf, unsigned max) +{ + int count; + int tmp; + struct usb_host_endpoint *hep = qh->hep; + struct urb *urb; + + count = snprintf(buf, max, " qh %p dev%d ep%d%s max%d\n", + qh, qh->dev->devnum, qh->epnum, + ({ char *s; switch (qh->type) { + case USB_ENDPOINT_XFER_BULK: + s = "-bulk"; break; + case USB_ENDPOINT_XFER_INT: + s = "-int"; break; + case USB_ENDPOINT_XFER_CONTROL: + s = ""; break; + default: + s = "iso"; break; + }; s; }), + qh->maxpacket); + if (count <= 0) + return 0; + buf += count; + max -= count; + + list_for_each_entry(urb, &hep->urb_list, urb_list) { + tmp = snprintf(buf, max, "\t%s urb %p %d/%d\n", + usb_pipein(urb->pipe) ? "in" : "out", + urb, urb->actual_length, + urb->transfer_buffer_length); + if (tmp <= 0) + break; + tmp = min(tmp, (int)max); + count += tmp; + buf += tmp; + max -= tmp; + } + return count; +} + +static int +dump_queue(struct list_head *q, char *buf, unsigned max) +{ + int count = 0; + struct musb_qh *qh; + + list_for_each_entry(qh, q, ring) { + int tmp; + + tmp = dump_qh(qh, buf, max); + if (tmp <= 0) + break; + tmp = min(tmp, (int)max); + count += tmp; + buf += tmp; + max -= tmp; + } + return count; +} + +#endif /* HCD */ + +#ifdef CONFIG_USB_GADGET_MUSB_HDRC +static int dump_ep(struct musb_ep *ep, char *buffer, unsigned max) +{ + char *buf = buffer; + int code = 0; + void __iomem *regs = ep->hw_ep->regs; + char *mode = "1buf"; + + if (ep->is_in) { + if (ep->hw_ep->tx_double_buffered) + mode = "2buf"; + } else { + if (ep->hw_ep->rx_double_buffered) + mode = "2buf"; + } + + do { + struct usb_request *req; + + code = snprintf(buf, max, + "\n%s (hw%d): %s%s, csr %04x maxp %04x\n", + ep->name, ep->current_epnum, + mode, ep->dma ? " dma" : "", + musb_readw(regs, + (ep->is_in || !ep->current_epnum) + ? MUSB_TXCSR + : MUSB_RXCSR), + musb_readw(regs, ep->is_in + ? MUSB_TXMAXP + : MUSB_RXMAXP) + ); + if (code <= 0) + break; + code = min(code, (int) max); + buf += code; + max -= code; + + if (is_cppi_enabled() && ep->current_epnum) { + unsigned cppi = ep->current_epnum - 1; + void __iomem *base = ep->musb->ctrl_base; + unsigned off1 = cppi << 2; + void __iomem *ram = base; + char tmp[16]; + + if (ep->is_in) { + ram += DAVINCI_TXCPPI_STATERAM_OFFSET(cppi); + tmp[0] = 0; + } else { + ram += DAVINCI_RXCPPI_STATERAM_OFFSET(cppi); + snprintf(tmp, sizeof tmp, "%d left, ", + musb_readl(base, + DAVINCI_RXCPPI_BUFCNT0_REG + off1)); + } + + code = snprintf(buf, max, "%cX DMA%d: %s" + "%08x %08x, %08x %08x; " + "%08x %08x %08x .. %08x\n", + ep->is_in ? 'T' : 'R', + ep->current_epnum - 1, tmp, + musb_readl(ram, 0 * 4), + musb_readl(ram, 1 * 4), + musb_readl(ram, 2 * 4), + musb_readl(ram, 3 * 4), + musb_readl(ram, 4 * 4), + musb_readl(ram, 5 * 4), + musb_readl(ram, 6 * 4), + musb_readl(ram, 7 * 4)); + if (code <= 0) + break; + code = min(code, (int) max); + buf += code; + max -= code; + } + + if (list_empty(&ep->req_list)) { + code = snprintf(buf, max, "\t(queue empty)\n"); + if (code <= 0) + break; + code = min(code, (int) max); + buf += code; + max -= code; + break; + } + list_for_each_entry(req, &ep->req_list, list) { + code = snprintf(buf, max, "\treq %p, %s%s%d/%d\n", + req, + req->zero ? "zero, " : "", + req->short_not_ok ? "!short, " : "", + req->actual, req->length); + if (code <= 0) + break; + code = min(code, (int) max); + buf += code; + max -= code; + } + } while (0); + return buf - buffer; +} +#endif + +static int +dump_end_info(struct musb *musb, u8 epnum, char *aBuffer, unsigned max) +{ + int code = 0; + char *buf = aBuffer; + struct musb_hw_ep *hw_ep = &musb->endpoints[epnum]; + + do { + musb_ep_select(musb->mregs, epnum); +#ifdef CONFIG_USB_MUSB_HDRC_HCD + if (is_host_active(musb)) { + int dump_rx, dump_tx; + void __iomem *regs = hw_ep->regs; + + /* TEMPORARY (!) until we have a real periodic + * schedule tree ... + */ + if (!epnum) { + /* control is shared, uses RX queue + * but (mostly) shadowed tx registers + */ + dump_tx = !list_empty(&musb->control); + dump_rx = 0; + } else if (hw_ep == musb->bulk_ep) { + dump_tx = !list_empty(&musb->out_bulk); + dump_rx = !list_empty(&musb->in_bulk); + } else if (musb->periodic[epnum]) { + struct usb_host_endpoint *hep; + + hep = musb->periodic[epnum]->hep; + dump_rx = hep->desc.bEndpointAddress + & USB_ENDPOINT_DIR_MASK; + dump_tx = !dump_rx; + } else + break; + /* END TEMPORARY */ + + + if (dump_rx) { + code = snprintf(buf, max, + "\nRX%d: %s rxcsr %04x interval %02x " + "max %04x type %02x; " + "dev %d hub %d port %d" + "\n", + epnum, + hw_ep->rx_double_buffered + ? "2buf" : "1buf", + musb_readw(regs, MUSB_RXCSR), + musb_readb(regs, MUSB_RXINTERVAL), + musb_readw(regs, MUSB_RXMAXP), + musb_readb(regs, MUSB_RXTYPE), + /* FIXME: assumes multipoint */ + musb_readb(musb->mregs, + MUSB_BUSCTL_OFFSET(epnum, + MUSB_RXFUNCADDR)), + musb_readb(musb->mregs, + MUSB_BUSCTL_OFFSET(epnum, + MUSB_RXHUBADDR)), + musb_readb(musb->mregs, + MUSB_BUSCTL_OFFSET(epnum, + MUSB_RXHUBPORT)) + ); + if (code <= 0) + break; + code = min(code, (int) max); + buf += code; + max -= code; + + if (is_cppi_enabled() + && epnum + && hw_ep->rx_channel) { + unsigned cppi = epnum - 1; + unsigned off1 = cppi << 2; + void __iomem *base; + void __iomem *ram; + char tmp[16]; + + base = musb->ctrl_base; + ram = DAVINCI_RXCPPI_STATERAM_OFFSET( + cppi) + base; + snprintf(tmp, sizeof tmp, "%d left, ", + musb_readl(base, + DAVINCI_RXCPPI_BUFCNT0_REG + + off1)); + + code = snprintf(buf, max, + " rx dma%d: %s" + "%08x %08x, %08x %08x; " + "%08x %08x %08x .. %08x\n", + cppi, tmp, + musb_readl(ram, 0 * 4), + musb_readl(ram, 1 * 4), + musb_readl(ram, 2 * 4), + musb_readl(ram, 3 * 4), + musb_readl(ram, 4 * 4), + musb_readl(ram, 5 * 4), + musb_readl(ram, 6 * 4), + musb_readl(ram, 7 * 4)); + if (code <= 0) + break; + code = min(code, (int) max); + buf += code; + max -= code; + } + + if (hw_ep == musb->bulk_ep + && !list_empty( + &musb->in_bulk)) { + code = dump_queue(&musb->in_bulk, + buf, max); + if (code <= 0) + break; + code = min(code, (int) max); + buf += code; + max -= code; + } else if (musb->periodic[epnum]) { + code = dump_qh(musb->periodic[epnum], + buf, max); + if (code <= 0) + break; + code = min(code, (int) max); + buf += code; + max -= code; + } + } + + if (dump_tx) { + code = snprintf(buf, max, + "\nTX%d: %s txcsr %04x interval %02x " + "max %04x type %02x; " + "dev %d hub %d port %d" + "\n", + epnum, + hw_ep->tx_double_buffered + ? "2buf" : "1buf", + musb_readw(regs, MUSB_TXCSR), + musb_readb(regs, MUSB_TXINTERVAL), + musb_readw(regs, MUSB_TXMAXP), + musb_readb(regs, MUSB_TXTYPE), + /* FIXME: assumes multipoint */ + musb_readb(musb->mregs, + MUSB_BUSCTL_OFFSET(epnum, + MUSB_TXFUNCADDR)), + musb_readb(musb->mregs, + MUSB_BUSCTL_OFFSET(epnum, + MUSB_TXHUBADDR)), + musb_readb(musb->mregs, + MUSB_BUSCTL_OFFSET(epnum, + MUSB_TXHUBPORT)) + ); + if (code <= 0) + break; + code = min(code, (int) max); + buf += code; + max -= code; + + if (is_cppi_enabled() + && epnum + && hw_ep->tx_channel) { + unsigned cppi = epnum - 1; + void __iomem *base; + void __iomem *ram; + + base = musb->ctrl_base; + ram = DAVINCI_RXCPPI_STATERAM_OFFSET( + cppi) + base; + code = snprintf(buf, max, + " tx dma%d: " + "%08x %08x, %08x %08x; " + "%08x %08x %08x .. %08x\n", + cppi, + musb_readl(ram, 0 * 4), + musb_readl(ram, 1 * 4), + musb_readl(ram, 2 * 4), + musb_readl(ram, 3 * 4), + musb_readl(ram, 4 * 4), + musb_readl(ram, 5 * 4), + musb_readl(ram, 6 * 4), + musb_readl(ram, 7 * 4)); + if (code <= 0) + break; + code = min(code, (int) max); + buf += code; + max -= code; + } + + if (hw_ep == musb->control_ep + && !list_empty( + &musb->control)) { + code = dump_queue(&musb->control, + buf, max); + if (code <= 0) + break; + code = min(code, (int) max); + buf += code; + max -= code; + } else if (hw_ep == musb->bulk_ep + && !list_empty( + &musb->out_bulk)) { + code = dump_queue(&musb->out_bulk, + buf, max); + if (code <= 0) + break; + code = min(code, (int) max); + buf += code; + max -= code; + } else if (musb->periodic[epnum]) { + code = dump_qh(musb->periodic[epnum], + buf, max); + if (code <= 0) + break; + code = min(code, (int) max); + buf += code; + max -= code; + } + } + } +#endif +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + if (is_peripheral_active(musb)) { + code = 0; + + if (hw_ep->ep_in.desc || !epnum) { + code = dump_ep(&hw_ep->ep_in, buf, max); + if (code <= 0) + break; + code = min(code, (int) max); + buf += code; + max -= code; + } + if (hw_ep->ep_out.desc) { + code = dump_ep(&hw_ep->ep_out, buf, max); + if (code <= 0) + break; + code = min(code, (int) max); + buf += code; + max -= code; + } + } +#endif + } while (0); + + return buf - aBuffer; +} + +/* Dump the current status and compile options. + * @param musb the device driver instance + * @param buffer where to dump the status; it must be big enough to hold the + * result otherwise "BAD THINGS HAPPENS(TM)". + */ +static int dump_header_stats(struct musb *musb, char *buffer) +{ + int code, count = 0; + const void __iomem *mbase = musb->mregs; + + *buffer = 0; + count = sprintf(buffer, "Status: %sHDRC, Mode=%s " + "(Power=%02x, DevCtl=%02x)\n", + (musb->is_multipoint ? "M" : ""), MUSB_MODE(musb), + musb_readb(mbase, MUSB_POWER), + musb_readb(mbase, MUSB_DEVCTL)); + if (count <= 0) + return 0; + buffer += count; + + code = sprintf(buffer, "OTG state: %s; %sactive\n", + otg_state_string(musb), + musb->is_active ? "" : "in"); + if (code <= 0) + goto done; + buffer += code; + count += code; + + code = sprintf(buffer, + "Options: " +#ifdef CONFIG_MUSB_PIO_ONLY + "pio" +#elif defined(CONFIG_USB_TI_CPPI_DMA) + "cppi-dma" +#elif defined(CONFIG_USB_INVENTRA_DMA) + "musb-dma" +#elif defined(CONFIG_USB_TUSB_OMAP_DMA) + "tusb-omap-dma" +#else + "?dma?" +#endif + ", " +#ifdef CONFIG_USB_MUSB_OTG + "otg (peripheral+host)" +#elif defined(CONFIG_USB_GADGET_MUSB_HDRC) + "peripheral" +#elif defined(CONFIG_USB_MUSB_HDRC_HCD) + "host" +#endif + ", debug=%d [eps=%d]\n", + debug, + musb->nr_endpoints); + if (code <= 0) + goto done; + count += code; + buffer += code; + +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + code = sprintf(buffer, "Peripheral address: %02x\n", + musb_readb(musb->ctrl_base, MUSB_FADDR)); + if (code <= 0) + goto done; + buffer += code; + count += code; +#endif + +#ifdef CONFIG_USB_MUSB_HDRC_HCD + code = sprintf(buffer, "Root port status: %08x\n", + musb->port1_status); + if (code <= 0) + goto done; + buffer += code; + count += code; +#endif + +#ifdef CONFIG_ARCH_DAVINCI + code = sprintf(buffer, + "DaVinci: ctrl=%02x stat=%1x phy=%03x\n" + "\trndis=%05x auto=%04x intsrc=%08x intmsk=%08x" + "\n", + musb_readl(musb->ctrl_base, DAVINCI_USB_CTRL_REG), + musb_readl(musb->ctrl_base, DAVINCI_USB_STAT_REG), + __raw_readl((void __force __iomem *) + IO_ADDRESS(USBPHY_CTL_PADDR)), + musb_readl(musb->ctrl_base, DAVINCI_RNDIS_REG), + musb_readl(musb->ctrl_base, DAVINCI_AUTOREQ_REG), + musb_readl(musb->ctrl_base, + DAVINCI_USB_INT_SOURCE_REG), + musb_readl(musb->ctrl_base, + DAVINCI_USB_INT_MASK_REG)); + if (code <= 0) + goto done; + count += code; + buffer += code; +#endif /* DAVINCI */ + +#ifdef CONFIG_USB_TUSB6010 + code = sprintf(buffer, + "TUSB6010: devconf %08x, phy enable %08x drive %08x" + "\n\totg %03x timer %08x" + "\n\tprcm conf %08x mgmt %08x; int src %08x mask %08x" + "\n", + musb_readl(musb->ctrl_base, TUSB_DEV_CONF), + musb_readl(musb->ctrl_base, TUSB_PHY_OTG_CTRL_ENABLE), + musb_readl(musb->ctrl_base, TUSB_PHY_OTG_CTRL), + musb_readl(musb->ctrl_base, TUSB_DEV_OTG_STAT), + musb_readl(musb->ctrl_base, TUSB_DEV_OTG_TIMER), + musb_readl(musb->ctrl_base, TUSB_PRCM_CONF), + musb_readl(musb->ctrl_base, TUSB_PRCM_MNGMT), + musb_readl(musb->ctrl_base, TUSB_INT_SRC), + musb_readl(musb->ctrl_base, TUSB_INT_MASK)); + if (code <= 0) + goto done; + count += code; + buffer += code; +#endif /* DAVINCI */ + + if (is_cppi_enabled() && musb->dma_controller) { + code = sprintf(buffer, + "CPPI: txcr=%d txsrc=%01x txena=%01x; " + "rxcr=%d rxsrc=%01x rxena=%01x " + "\n", + musb_readl(musb->ctrl_base, + DAVINCI_TXCPPI_CTRL_REG), + musb_readl(musb->ctrl_base, + DAVINCI_TXCPPI_RAW_REG), + musb_readl(musb->ctrl_base, + DAVINCI_TXCPPI_INTENAB_REG), + musb_readl(musb->ctrl_base, + DAVINCI_RXCPPI_CTRL_REG), + musb_readl(musb->ctrl_base, + DAVINCI_RXCPPI_RAW_REG), + musb_readl(musb->ctrl_base, + DAVINCI_RXCPPI_INTENAB_REG)); + if (code <= 0) + goto done; + count += code; + buffer += code; + } + +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + if (is_peripheral_enabled(musb)) { + code = sprintf(buffer, "Gadget driver: %s\n", + musb->gadget_driver + ? musb->gadget_driver->driver.name + : "(none)"); + if (code <= 0) + goto done; + count += code; + buffer += code; + } +#endif + +done: + return count; +} + +/* Write to ProcFS + * + * C soft-connect + * c soft-disconnect + * I enable HS + * i disable HS + * s stop session + * F force session (OTG-unfriendly) + * E rElinquish bus (OTG) + * H request host mode + * h cancel host request + * T start sending TEST_PACKET + * D set/query the debug level + */ +static int musb_proc_write(struct file *file, const char __user *buffer, + unsigned long count, void *data) +{ + char cmd; + u8 reg; + struct musb *musb = (struct musb *)data; + void __iomem *mbase = musb->mregs; + + /* MOD_INC_USE_COUNT; */ + + if (unlikely(copy_from_user(&cmd, buffer, 1))) + return -EFAULT; + + switch (cmd) { + case 'C': + if (mbase) { + reg = musb_readb(mbase, MUSB_POWER) + | MUSB_POWER_SOFTCONN; + musb_writeb(mbase, MUSB_POWER, reg); + } + break; + + case 'c': + if (mbase) { + reg = musb_readb(mbase, MUSB_POWER) + & ~MUSB_POWER_SOFTCONN; + musb_writeb(mbase, MUSB_POWER, reg); + } + break; + + case 'I': + if (mbase) { + reg = musb_readb(mbase, MUSB_POWER) + | MUSB_POWER_HSENAB; + musb_writeb(mbase, MUSB_POWER, reg); + } + break; + + case 'i': + if (mbase) { + reg = musb_readb(mbase, MUSB_POWER) + & ~MUSB_POWER_HSENAB; + musb_writeb(mbase, MUSB_POWER, reg); + } + break; + + case 'F': + reg = musb_readb(mbase, MUSB_DEVCTL); + reg |= MUSB_DEVCTL_SESSION; + musb_writeb(mbase, MUSB_DEVCTL, reg); + break; + + case 'H': + if (mbase) { + reg = musb_readb(mbase, MUSB_DEVCTL); + reg |= MUSB_DEVCTL_HR; + musb_writeb(mbase, MUSB_DEVCTL, reg); + /* MUSB_HST_MODE( ((struct musb*)data) ); */ + /* WARNING("Host Mode\n"); */ + } + break; + + case 'h': + if (mbase) { + reg = musb_readb(mbase, MUSB_DEVCTL); + reg &= ~MUSB_DEVCTL_HR; + musb_writeb(mbase, MUSB_DEVCTL, reg); + } + break; + + case 'T': + if (mbase) { + musb_load_testpacket(musb); + musb_writeb(mbase, MUSB_TESTMODE, + MUSB_TEST_PACKET); + } + break; + +#if (MUSB_DEBUG > 0) + /* set/read debug level */ + case 'D':{ + if (count > 1) { + char digits[8], *p = digits; + int i = 0, level = 0, sign = 1; + int len = min(count - 1, (unsigned long)8); + + if (copy_from_user(&digits, &buffer[1], len)) + return -EFAULT; + + /* optional sign */ + if (*p == '-') { + len -= 1; + sign = -sign; + p++; + } + + /* read it */ + while (i++ < len && *p > '0' && *p < '9') { + level = level * 10 + (*p - '0'); + p++; + } + + level *= sign; + DBG(1, "debug level %d\n", level); + debug = level; + } + } + break; + + + case '?': + INFO("?: you are seeing it\n"); + INFO("C/c: soft connect enable/disable\n"); + INFO("I/i: hispeed enable/disable\n"); + INFO("F: force session start\n"); + INFO("H: host mode\n"); + INFO("T: start sending TEST_PACKET\n"); + INFO("D: set/read dbug level\n"); + break; +#endif + + default: + ERR("Command %c not implemented\n", cmd); + break; + } + + musb_platform_try_idle(musb, 0); + + return count; +} + +static int musb_proc_read(char *page, char **start, + off_t off, int count, int *eof, void *data) +{ + char *buffer = page; + int code = 0; + unsigned long flags; + struct musb *musb = data; + unsigned epnum; + + count -= off; + count -= 1; /* for NUL at end */ + if (count <= 0) + return -EINVAL; + + spin_lock_irqsave(&musb->lock, flags); + + code = dump_header_stats(musb, buffer); + if (code > 0) { + buffer += code; + count -= code; + } + + /* generate the report for the end points */ + /* REVISIT ... not unless something's connected! */ + for (epnum = 0; count >= 0 && epnum < musb->nr_endpoints; + epnum++) { + code = dump_end_info(musb, epnum, buffer, count); + if (code > 0) { + buffer += code; + count -= code; + } + } + + musb_platform_try_idle(musb, 0); + + spin_unlock_irqrestore(&musb->lock, flags); + *eof = 1; + + return buffer - page; +} + +void __devexit musb_debug_delete(char *name, struct musb *musb) +{ + if (musb->proc_entry) + remove_proc_entry(name, NULL); +} + +struct proc_dir_entry *__init +musb_debug_create(char *name, struct musb *data) +{ + struct proc_dir_entry *pde; + + /* FIXME convert everything to seq_file; then later, debugfs */ + + if (!name) + return NULL; + + pde = create_proc_entry(name, S_IFREG | S_IRUGO | S_IWUSR, NULL); + data->proc_entry = pde; + if (pde) { + pde->data = data; + /* pde->owner = THIS_MODULE; */ + + pde->read_proc = musb_proc_read; + pde->write_proc = musb_proc_write; + + pde->size = 0; + + pr_debug("Registered /proc/%s\n", name); + } else { + pr_debug("Cannot create a valid proc file entry"); + } + + return pde; +} diff --git a/drivers/usb/musb/musb_regs.h b/drivers/usb/musb/musb_regs.h new file mode 100644 index 00000000000..9c228661aa5 --- /dev/null +++ b/drivers/usb/musb/musb_regs.h @@ -0,0 +1,300 @@ +/* + * MUSB OTG driver register defines + * + * Copyright 2005 Mentor Graphics Corporation + * Copyright (C) 2005-2006 by Texas Instruments + * Copyright (C) 2006-2007 Nokia Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + */ + +#ifndef __MUSB_REGS_H__ +#define __MUSB_REGS_H__ + +#define MUSB_EP0_FIFOSIZE 64 /* This is non-configurable */ + +/* + * Common USB registers + */ + +#define MUSB_FADDR 0x00 /* 8-bit */ +#define MUSB_POWER 0x01 /* 8-bit */ + +#define MUSB_INTRTX 0x02 /* 16-bit */ +#define MUSB_INTRRX 0x04 +#define MUSB_INTRTXE 0x06 +#define MUSB_INTRRXE 0x08 +#define MUSB_INTRUSB 0x0A /* 8 bit */ +#define MUSB_INTRUSBE 0x0B /* 8 bit */ +#define MUSB_FRAME 0x0C +#define MUSB_INDEX 0x0E /* 8 bit */ +#define MUSB_TESTMODE 0x0F /* 8 bit */ + +/* Get offset for a given FIFO from musb->mregs */ +#ifdef CONFIG_USB_TUSB6010 +#define MUSB_FIFO_OFFSET(epnum) (0x200 + ((epnum) * 0x20)) +#else +#define MUSB_FIFO_OFFSET(epnum) (0x20 + ((epnum) * 4)) +#endif + +/* + * Additional Control Registers + */ + +#define MUSB_DEVCTL 0x60 /* 8 bit */ + +/* These are always controlled through the INDEX register */ +#define MUSB_TXFIFOSZ 0x62 /* 8-bit (see masks) */ +#define MUSB_RXFIFOSZ 0x63 /* 8-bit (see masks) */ +#define MUSB_TXFIFOADD 0x64 /* 16-bit offset shifted right 3 */ +#define MUSB_RXFIFOADD 0x66 /* 16-bit offset shifted right 3 */ + +/* REVISIT: vctrl/vstatus: optional vendor utmi+phy register at 0x68 */ +#define MUSB_HWVERS 0x6C /* 8 bit */ + +#define MUSB_EPINFO 0x78 /* 8 bit */ +#define MUSB_RAMINFO 0x79 /* 8 bit */ +#define MUSB_LINKINFO 0x7a /* 8 bit */ +#define MUSB_VPLEN 0x7b /* 8 bit */ +#define MUSB_HS_EOF1 0x7c /* 8 bit */ +#define MUSB_FS_EOF1 0x7d /* 8 bit */ +#define MUSB_LS_EOF1 0x7e /* 8 bit */ + +/* Offsets to endpoint registers */ +#define MUSB_TXMAXP 0x00 +#define MUSB_TXCSR 0x02 +#define MUSB_CSR0 MUSB_TXCSR /* Re-used for EP0 */ +#define MUSB_RXMAXP 0x04 +#define MUSB_RXCSR 0x06 +#define MUSB_RXCOUNT 0x08 +#define MUSB_COUNT0 MUSB_RXCOUNT /* Re-used for EP0 */ +#define MUSB_TXTYPE 0x0A +#define MUSB_TYPE0 MUSB_TXTYPE /* Re-used for EP0 */ +#define MUSB_TXINTERVAL 0x0B +#define MUSB_NAKLIMIT0 MUSB_TXINTERVAL /* Re-used for EP0 */ +#define MUSB_RXTYPE 0x0C +#define MUSB_RXINTERVAL 0x0D +#define MUSB_FIFOSIZE 0x0F +#define MUSB_CONFIGDATA MUSB_FIFOSIZE /* Re-used for EP0 */ + +/* Offsets to endpoint registers in indexed model (using INDEX register) */ +#define MUSB_INDEXED_OFFSET(_epnum, _offset) \ + (0x10 + (_offset)) + +/* Offsets to endpoint registers in flat models */ +#define MUSB_FLAT_OFFSET(_epnum, _offset) \ + (0x100 + (0x10*(_epnum)) + (_offset)) + +#ifdef CONFIG_USB_TUSB6010 +/* TUSB6010 EP0 configuration register is special */ +#define MUSB_TUSB_OFFSET(_epnum, _offset) \ + (0x10 + _offset) +#include "tusb6010.h" /* Needed "only" for TUSB_EP0_CONF */ +#endif + +/* "bus control"/target registers, for host side multipoint (external hubs) */ +#define MUSB_TXFUNCADDR 0x00 +#define MUSB_TXHUBADDR 0x02 +#define MUSB_TXHUBPORT 0x03 + +#define MUSB_RXFUNCADDR 0x04 +#define MUSB_RXHUBADDR 0x06 +#define MUSB_RXHUBPORT 0x07 + +#define MUSB_BUSCTL_OFFSET(_epnum, _offset) \ + (0x80 + (8*(_epnum)) + (_offset)) + +/* + * MUSB Register bits + */ + +/* POWER */ +#define MUSB_POWER_ISOUPDATE 0x80 +#define MUSB_POWER_SOFTCONN 0x40 +#define MUSB_POWER_HSENAB 0x20 +#define MUSB_POWER_HSMODE 0x10 +#define MUSB_POWER_RESET 0x08 +#define MUSB_POWER_RESUME 0x04 +#define MUSB_POWER_SUSPENDM 0x02 +#define MUSB_POWER_ENSUSPEND 0x01 + +/* INTRUSB */ +#define MUSB_INTR_SUSPEND 0x01 +#define MUSB_INTR_RESUME 0x02 +#define MUSB_INTR_RESET 0x04 +#define MUSB_INTR_BABBLE 0x04 +#define MUSB_INTR_SOF 0x08 +#define MUSB_INTR_CONNECT 0x10 +#define MUSB_INTR_DISCONNECT 0x20 +#define MUSB_INTR_SESSREQ 0x40 +#define MUSB_INTR_VBUSERROR 0x80 /* For SESSION end */ + +/* DEVCTL */ +#define MUSB_DEVCTL_BDEVICE 0x80 +#define MUSB_DEVCTL_FSDEV 0x40 +#define MUSB_DEVCTL_LSDEV 0x20 +#define MUSB_DEVCTL_VBUS 0x18 +#define MUSB_DEVCTL_VBUS_SHIFT 3 +#define MUSB_DEVCTL_HM 0x04 +#define MUSB_DEVCTL_HR 0x02 +#define MUSB_DEVCTL_SESSION 0x01 + +/* TESTMODE */ +#define MUSB_TEST_FORCE_HOST 0x80 +#define MUSB_TEST_FIFO_ACCESS 0x40 +#define MUSB_TEST_FORCE_FS 0x20 +#define MUSB_TEST_FORCE_HS 0x10 +#define MUSB_TEST_PACKET 0x08 +#define MUSB_TEST_K 0x04 +#define MUSB_TEST_J 0x02 +#define MUSB_TEST_SE0_NAK 0x01 + +/* Allocate for double-packet buffering (effectively doubles assigned _SIZE) */ +#define MUSB_FIFOSZ_DPB 0x10 +/* Allocation size (8, 16, 32, ... 4096) */ +#define MUSB_FIFOSZ_SIZE 0x0f + +/* CSR0 */ +#define MUSB_CSR0_FLUSHFIFO 0x0100 +#define MUSB_CSR0_TXPKTRDY 0x0002 +#define MUSB_CSR0_RXPKTRDY 0x0001 + +/* CSR0 in Peripheral mode */ +#define MUSB_CSR0_P_SVDSETUPEND 0x0080 +#define MUSB_CSR0_P_SVDRXPKTRDY 0x0040 +#define MUSB_CSR0_P_SENDSTALL 0x0020 +#define MUSB_CSR0_P_SETUPEND 0x0010 +#define MUSB_CSR0_P_DATAEND 0x0008 +#define MUSB_CSR0_P_SENTSTALL 0x0004 + +/* CSR0 in Host mode */ +#define MUSB_CSR0_H_DIS_PING 0x0800 +#define MUSB_CSR0_H_WR_DATATOGGLE 0x0400 /* Set to allow setting: */ +#define MUSB_CSR0_H_DATATOGGLE 0x0200 /* Data toggle control */ +#define MUSB_CSR0_H_NAKTIMEOUT 0x0080 +#define MUSB_CSR0_H_STATUSPKT 0x0040 +#define MUSB_CSR0_H_REQPKT 0x0020 +#define MUSB_CSR0_H_ERROR 0x0010 +#define MUSB_CSR0_H_SETUPPKT 0x0008 +#define MUSB_CSR0_H_RXSTALL 0x0004 + +/* CSR0 bits to avoid zeroing (write zero clears, write 1 ignored) */ +#define MUSB_CSR0_P_WZC_BITS \ + (MUSB_CSR0_P_SENTSTALL) +#define MUSB_CSR0_H_WZC_BITS \ + (MUSB_CSR0_H_NAKTIMEOUT | MUSB_CSR0_H_RXSTALL \ + | MUSB_CSR0_RXPKTRDY) + +/* TxType/RxType */ +#define MUSB_TYPE_SPEED 0xc0 +#define MUSB_TYPE_SPEED_SHIFT 6 +#define MUSB_TYPE_PROTO 0x30 /* Implicitly zero for ep0 */ +#define MUSB_TYPE_PROTO_SHIFT 4 +#define MUSB_TYPE_REMOTE_END 0xf /* Implicitly zero for ep0 */ + +/* CONFIGDATA */ +#define MUSB_CONFIGDATA_MPRXE 0x80 /* Auto bulk pkt combining */ +#define MUSB_CONFIGDATA_MPTXE 0x40 /* Auto bulk pkt splitting */ +#define MUSB_CONFIGDATA_BIGENDIAN 0x20 +#define MUSB_CONFIGDATA_HBRXE 0x10 /* HB-ISO for RX */ +#define MUSB_CONFIGDATA_HBTXE 0x08 /* HB-ISO for TX */ +#define MUSB_CONFIGDATA_DYNFIFO 0x04 /* Dynamic FIFO sizing */ +#define MUSB_CONFIGDATA_SOFTCONE 0x02 /* SoftConnect */ +#define MUSB_CONFIGDATA_UTMIDW 0x01 /* Data width 0/1 => 8/16bits */ + +/* TXCSR in Peripheral and Host mode */ +#define MUSB_TXCSR_AUTOSET 0x8000 +#define MUSB_TXCSR_MODE 0x2000 +#define MUSB_TXCSR_DMAENAB 0x1000 +#define MUSB_TXCSR_FRCDATATOG 0x0800 +#define MUSB_TXCSR_DMAMODE 0x0400 +#define MUSB_TXCSR_CLRDATATOG 0x0040 +#define MUSB_TXCSR_FLUSHFIFO 0x0008 +#define MUSB_TXCSR_FIFONOTEMPTY 0x0002 +#define MUSB_TXCSR_TXPKTRDY 0x0001 + +/* TXCSR in Peripheral mode */ +#define MUSB_TXCSR_P_ISO 0x4000 +#define MUSB_TXCSR_P_INCOMPTX 0x0080 +#define MUSB_TXCSR_P_SENTSTALL 0x0020 +#define MUSB_TXCSR_P_SENDSTALL 0x0010 +#define MUSB_TXCSR_P_UNDERRUN 0x0004 + +/* TXCSR in Host mode */ +#define MUSB_TXCSR_H_WR_DATATOGGLE 0x0200 +#define MUSB_TXCSR_H_DATATOGGLE 0x0100 +#define MUSB_TXCSR_H_NAKTIMEOUT 0x0080 +#define MUSB_TXCSR_H_RXSTALL 0x0020 +#define MUSB_TXCSR_H_ERROR 0x0004 + +/* TXCSR bits to avoid zeroing (write zero clears, write 1 ignored) */ +#define MUSB_TXCSR_P_WZC_BITS \ + (MUSB_TXCSR_P_INCOMPTX | MUSB_TXCSR_P_SENTSTALL \ + | MUSB_TXCSR_P_UNDERRUN | MUSB_TXCSR_FIFONOTEMPTY) +#define MUSB_TXCSR_H_WZC_BITS \ + (MUSB_TXCSR_H_NAKTIMEOUT | MUSB_TXCSR_H_RXSTALL \ + | MUSB_TXCSR_H_ERROR | MUSB_TXCSR_FIFONOTEMPTY) + +/* RXCSR in Peripheral and Host mode */ +#define MUSB_RXCSR_AUTOCLEAR 0x8000 +#define MUSB_RXCSR_DMAENAB 0x2000 +#define MUSB_RXCSR_DISNYET 0x1000 +#define MUSB_RXCSR_PID_ERR 0x1000 +#define MUSB_RXCSR_DMAMODE 0x0800 +#define MUSB_RXCSR_INCOMPRX 0x0100 +#define MUSB_RXCSR_CLRDATATOG 0x0080 +#define MUSB_RXCSR_FLUSHFIFO 0x0010 +#define MUSB_RXCSR_DATAERROR 0x0008 +#define MUSB_RXCSR_FIFOFULL 0x0002 +#define MUSB_RXCSR_RXPKTRDY 0x0001 + +/* RXCSR in Peripheral mode */ +#define MUSB_RXCSR_P_ISO 0x4000 +#define MUSB_RXCSR_P_SENTSTALL 0x0040 +#define MUSB_RXCSR_P_SENDSTALL 0x0020 +#define MUSB_RXCSR_P_OVERRUN 0x0004 + +/* RXCSR in Host mode */ +#define MUSB_RXCSR_H_AUTOREQ 0x4000 +#define MUSB_RXCSR_H_WR_DATATOGGLE 0x0400 +#define MUSB_RXCSR_H_DATATOGGLE 0x0200 +#define MUSB_RXCSR_H_RXSTALL 0x0040 +#define MUSB_RXCSR_H_REQPKT 0x0020 +#define MUSB_RXCSR_H_ERROR 0x0004 + +/* RXCSR bits to avoid zeroing (write zero clears, write 1 ignored) */ +#define MUSB_RXCSR_P_WZC_BITS \ + (MUSB_RXCSR_P_SENTSTALL | MUSB_RXCSR_P_OVERRUN \ + | MUSB_RXCSR_RXPKTRDY) +#define MUSB_RXCSR_H_WZC_BITS \ + (MUSB_RXCSR_H_RXSTALL | MUSB_RXCSR_H_ERROR \ + | MUSB_RXCSR_DATAERROR | MUSB_RXCSR_RXPKTRDY) + +/* HUBADDR */ +#define MUSB_HUBADDR_MULTI_TT 0x80 + +#endif /* __MUSB_REGS_H__ */ diff --git a/drivers/usb/musb/musb_virthub.c b/drivers/usb/musb/musb_virthub.c new file mode 100644 index 00000000000..e0e9ce58417 --- /dev/null +++ b/drivers/usb/musb/musb_virthub.c @@ -0,0 +1,425 @@ +/* + * MUSB OTG driver virtual root hub support + * + * Copyright 2005 Mentor Graphics Corporation + * Copyright (C) 2005-2006 by Texas Instruments + * Copyright (C) 2006-2007 Nokia Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +#include "musb_core.h" + + +static void musb_port_suspend(struct musb *musb, bool do_suspend) +{ + u8 power; + void __iomem *mbase = musb->mregs; + + if (!is_host_active(musb)) + return; + + /* NOTE: this doesn't necessarily put PHY into low power mode, + * turning off its clock; that's a function of PHY integration and + * MUSB_POWER_ENSUSPEND. PHY may need a clock (sigh) to detect + * SE0 changing to connect (J) or wakeup (K) states. + */ + power = musb_readb(mbase, MUSB_POWER); + if (do_suspend) { + int retries = 10000; + + power &= ~MUSB_POWER_RESUME; + power |= MUSB_POWER_SUSPENDM; + musb_writeb(mbase, MUSB_POWER, power); + + /* Needed for OPT A tests */ + power = musb_readb(mbase, MUSB_POWER); + while (power & MUSB_POWER_SUSPENDM) { + power = musb_readb(mbase, MUSB_POWER); + if (retries-- < 1) + break; + } + + DBG(3, "Root port suspended, power %02x\n", power); + + musb->port1_status |= USB_PORT_STAT_SUSPEND; + switch (musb->xceiv.state) { + case OTG_STATE_A_HOST: + musb->xceiv.state = OTG_STATE_A_SUSPEND; + musb->is_active = is_otg_enabled(musb) + && musb->xceiv.host->b_hnp_enable; + musb_platform_try_idle(musb, 0); + break; +#ifdef CONFIG_USB_MUSB_OTG + case OTG_STATE_B_HOST: + musb->xceiv.state = OTG_STATE_B_WAIT_ACON; + musb->is_active = is_otg_enabled(musb) + && musb->xceiv.host->b_hnp_enable; + musb_platform_try_idle(musb, 0); + break; +#endif + default: + DBG(1, "bogus rh suspend? %s\n", + otg_state_string(musb)); + } + } else if (power & MUSB_POWER_SUSPENDM) { + power &= ~MUSB_POWER_SUSPENDM; + power |= MUSB_POWER_RESUME; + musb_writeb(mbase, MUSB_POWER, power); + + DBG(3, "Root port resuming, power %02x\n", power); + + /* later, GetPortStatus will stop RESUME signaling */ + musb->port1_status |= MUSB_PORT_STAT_RESUME; + musb->rh_timer = jiffies + msecs_to_jiffies(20); + } +} + +static void musb_port_reset(struct musb *musb, bool do_reset) +{ + u8 power; + void __iomem *mbase = musb->mregs; + +#ifdef CONFIG_USB_MUSB_OTG + if (musb->xceiv.state == OTG_STATE_B_IDLE) { + DBG(2, "HNP: Returning from HNP; no hub reset from b_idle\n"); + musb->port1_status &= ~USB_PORT_STAT_RESET; + return; + } +#endif + + if (!is_host_active(musb)) + return; + + /* NOTE: caller guarantees it will turn off the reset when + * the appropriate amount of time has passed + */ + power = musb_readb(mbase, MUSB_POWER); + if (do_reset) { + + /* + * If RESUME is set, we must make sure it stays minimum 20 ms. + * Then we must clear RESUME and wait a bit to let musb start + * generating SOFs. If we don't do this, OPT HS A 6.8 tests + * fail with "Error! Did not receive an SOF before suspend + * detected". + */ + if (power & MUSB_POWER_RESUME) { + while (time_before(jiffies, musb->rh_timer)) + msleep(1); + musb_writeb(mbase, MUSB_POWER, + power & ~MUSB_POWER_RESUME); + msleep(1); + } + + musb->ignore_disconnect = true; + power &= 0xf0; + musb_writeb(mbase, MUSB_POWER, + power | MUSB_POWER_RESET); + + musb->port1_status |= USB_PORT_STAT_RESET; + musb->port1_status &= ~USB_PORT_STAT_ENABLE; + musb->rh_timer = jiffies + msecs_to_jiffies(50); + } else { + DBG(4, "root port reset stopped\n"); + musb_writeb(mbase, MUSB_POWER, + power & ~MUSB_POWER_RESET); + + musb->ignore_disconnect = false; + + power = musb_readb(mbase, MUSB_POWER); + if (power & MUSB_POWER_HSMODE) { + DBG(4, "high-speed device connected\n"); + musb->port1_status |= USB_PORT_STAT_HIGH_SPEED; + } + + musb->port1_status &= ~USB_PORT_STAT_RESET; + musb->port1_status |= USB_PORT_STAT_ENABLE + | (USB_PORT_STAT_C_RESET << 16) + | (USB_PORT_STAT_C_ENABLE << 16); + usb_hcd_poll_rh_status(musb_to_hcd(musb)); + + musb->vbuserr_retry = VBUSERR_RETRY_COUNT; + } +} + +void musb_root_disconnect(struct musb *musb) +{ + musb->port1_status = (1 << USB_PORT_FEAT_POWER) + | (1 << USB_PORT_FEAT_C_CONNECTION); + + usb_hcd_poll_rh_status(musb_to_hcd(musb)); + musb->is_active = 0; + + switch (musb->xceiv.state) { + case OTG_STATE_A_HOST: + case OTG_STATE_A_SUSPEND: + musb->xceiv.state = OTG_STATE_A_WAIT_BCON; + musb->is_active = 0; + break; + case OTG_STATE_A_WAIT_VFALL: + musb->xceiv.state = OTG_STATE_B_IDLE; + break; + default: + DBG(1, "host disconnect (%s)\n", otg_state_string(musb)); + } +} + + +/*---------------------------------------------------------------------*/ + +/* Caller may or may not hold musb->lock */ +int musb_hub_status_data(struct usb_hcd *hcd, char *buf) +{ + struct musb *musb = hcd_to_musb(hcd); + int retval = 0; + + /* called in_irq() via usb_hcd_poll_rh_status() */ + if (musb->port1_status & 0xffff0000) { + *buf = 0x02; + retval = 1; + } + return retval; +} + +int musb_hub_control( + struct usb_hcd *hcd, + u16 typeReq, + u16 wValue, + u16 wIndex, + char *buf, + u16 wLength) +{ + struct musb *musb = hcd_to_musb(hcd); + u32 temp; + int retval = 0; + unsigned long flags; + + spin_lock_irqsave(&musb->lock, flags); + + if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags))) { + spin_unlock_irqrestore(&musb->lock, flags); + return -ESHUTDOWN; + } + + /* hub features: always zero, setting is a NOP + * port features: reported, sometimes updated when host is active + * no indicators + */ + switch (typeReq) { + case ClearHubFeature: + case SetHubFeature: + switch (wValue) { + case C_HUB_OVER_CURRENT: + case C_HUB_LOCAL_POWER: + break; + default: + goto error; + } + break; + case ClearPortFeature: + if ((wIndex & 0xff) != 1) + goto error; + + switch (wValue) { + case USB_PORT_FEAT_ENABLE: + break; + case USB_PORT_FEAT_SUSPEND: + musb_port_suspend(musb, false); + break; + case USB_PORT_FEAT_POWER: + if (!(is_otg_enabled(musb) && hcd->self.is_b_host)) + musb_set_vbus(musb, 0); + break; + case USB_PORT_FEAT_C_CONNECTION: + case USB_PORT_FEAT_C_ENABLE: + case USB_PORT_FEAT_C_OVER_CURRENT: + case USB_PORT_FEAT_C_RESET: + case USB_PORT_FEAT_C_SUSPEND: + break; + default: + goto error; + } + DBG(5, "clear feature %d\n", wValue); + musb->port1_status &= ~(1 << wValue); + break; + case GetHubDescriptor: + { + struct usb_hub_descriptor *desc = (void *)buf; + + desc->bDescLength = 9; + desc->bDescriptorType = 0x29; + desc->bNbrPorts = 1; + desc->wHubCharacteristics = __constant_cpu_to_le16( + 0x0001 /* per-port power switching */ + | 0x0010 /* no overcurrent reporting */ + ); + desc->bPwrOn2PwrGood = 5; /* msec/2 */ + desc->bHubContrCurrent = 0; + + /* workaround bogus struct definition */ + desc->DeviceRemovable[0] = 0x02; /* port 1 */ + desc->DeviceRemovable[1] = 0xff; + } + break; + case GetHubStatus: + temp = 0; + *(__le32 *) buf = cpu_to_le32(temp); + break; + case GetPortStatus: + if (wIndex != 1) + goto error; + + /* finish RESET signaling? */ + if ((musb->port1_status & USB_PORT_STAT_RESET) + && time_after_eq(jiffies, musb->rh_timer)) + musb_port_reset(musb, false); + + /* finish RESUME signaling? */ + if ((musb->port1_status & MUSB_PORT_STAT_RESUME) + && time_after_eq(jiffies, musb->rh_timer)) { + u8 power; + + power = musb_readb(musb->mregs, MUSB_POWER); + power &= ~MUSB_POWER_RESUME; + DBG(4, "root port resume stopped, power %02x\n", + power); + musb_writeb(musb->mregs, MUSB_POWER, power); + + /* ISSUE: DaVinci (RTL 1.300) disconnects after + * resume of high speed peripherals (but not full + * speed ones). + */ + + musb->is_active = 1; + musb->port1_status &= ~(USB_PORT_STAT_SUSPEND + | MUSB_PORT_STAT_RESUME); + musb->port1_status |= USB_PORT_STAT_C_SUSPEND << 16; + usb_hcd_poll_rh_status(musb_to_hcd(musb)); + /* NOTE: it might really be A_WAIT_BCON ... */ + musb->xceiv.state = OTG_STATE_A_HOST; + } + + put_unaligned(cpu_to_le32(musb->port1_status + & ~MUSB_PORT_STAT_RESUME), + (__le32 *) buf); + + /* port change status is more interesting */ + DBG(get_unaligned((u16 *)(buf+2)) ? 2 : 5, "port status %08x\n", + musb->port1_status); + break; + case SetPortFeature: + if ((wIndex & 0xff) != 1) + goto error; + + switch (wValue) { + case USB_PORT_FEAT_POWER: + /* NOTE: this controller has a strange state machine + * that involves "requesting sessions" according to + * magic side effects from incompletely-described + * rules about startup... + * + * This call is what really starts the host mode; be + * very careful about side effects if you reorder any + * initialization logic, e.g. for OTG, or change any + * logic relating to VBUS power-up. + */ + if (!(is_otg_enabled(musb) && hcd->self.is_b_host)) + musb_start(musb); + break; + case USB_PORT_FEAT_RESET: + musb_port_reset(musb, true); + break; + case USB_PORT_FEAT_SUSPEND: + musb_port_suspend(musb, true); + break; + case USB_PORT_FEAT_TEST: + if (unlikely(is_host_active(musb))) + goto error; + + wIndex >>= 8; + switch (wIndex) { + case 1: + pr_debug("TEST_J\n"); + temp = MUSB_TEST_J; + break; + case 2: + pr_debug("TEST_K\n"); + temp = MUSB_TEST_K; + break; + case 3: + pr_debug("TEST_SE0_NAK\n"); + temp = MUSB_TEST_SE0_NAK; + break; + case 4: + pr_debug("TEST_PACKET\n"); + temp = MUSB_TEST_PACKET; + musb_load_testpacket(musb); + break; + case 5: + pr_debug("TEST_FORCE_ENABLE\n"); + temp = MUSB_TEST_FORCE_HOST + | MUSB_TEST_FORCE_HS; + + musb_writeb(musb->mregs, MUSB_DEVCTL, + MUSB_DEVCTL_SESSION); + break; + case 6: + pr_debug("TEST_FIFO_ACCESS\n"); + temp = MUSB_TEST_FIFO_ACCESS; + break; + default: + goto error; + } + musb_writeb(musb->mregs, MUSB_TESTMODE, temp); + break; + default: + goto error; + } + DBG(5, "set feature %d\n", wValue); + musb->port1_status |= 1 << wValue; + break; + + default: +error: + /* "protocol stall" on error */ + retval = -EPIPE; + } + spin_unlock_irqrestore(&musb->lock, flags); + return retval; +} diff --git a/drivers/usb/musb/musbhsdma.c b/drivers/usb/musb/musbhsdma.c new file mode 100644 index 00000000000..9ba8fb7fcd2 --- /dev/null +++ b/drivers/usb/musb/musbhsdma.c @@ -0,0 +1,433 @@ +/* + * MUSB OTG driver - support for Mentor's DMA controller + * + * Copyright 2005 Mentor Graphics Corporation + * Copyright (C) 2005-2007 by Texas Instruments + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + */ +#include +#include +#include +#include "musb_core.h" + +#if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3430) +#include "omap2430.h" +#endif + +#define MUSB_HSDMA_BASE 0x200 +#define MUSB_HSDMA_INTR (MUSB_HSDMA_BASE + 0) +#define MUSB_HSDMA_CONTROL 0x4 +#define MUSB_HSDMA_ADDRESS 0x8 +#define MUSB_HSDMA_COUNT 0xc + +#define MUSB_HSDMA_CHANNEL_OFFSET(_bChannel, _offset) \ + (MUSB_HSDMA_BASE + (_bChannel << 4) + _offset) + +/* control register (16-bit): */ +#define MUSB_HSDMA_ENABLE_SHIFT 0 +#define MUSB_HSDMA_TRANSMIT_SHIFT 1 +#define MUSB_HSDMA_MODE1_SHIFT 2 +#define MUSB_HSDMA_IRQENABLE_SHIFT 3 +#define MUSB_HSDMA_ENDPOINT_SHIFT 4 +#define MUSB_HSDMA_BUSERROR_SHIFT 8 +#define MUSB_HSDMA_BURSTMODE_SHIFT 9 +#define MUSB_HSDMA_BURSTMODE (3 << MUSB_HSDMA_BURSTMODE_SHIFT) +#define MUSB_HSDMA_BURSTMODE_UNSPEC 0 +#define MUSB_HSDMA_BURSTMODE_INCR4 1 +#define MUSB_HSDMA_BURSTMODE_INCR8 2 +#define MUSB_HSDMA_BURSTMODE_INCR16 3 + +#define MUSB_HSDMA_CHANNELS 8 + +struct musb_dma_controller; + +struct musb_dma_channel { + struct dma_channel Channel; + struct musb_dma_controller *controller; + u32 dwStartAddress; + u32 len; + u16 wMaxPacketSize; + u8 bIndex; + u8 epnum; + u8 transmit; +}; + +struct musb_dma_controller { + struct dma_controller Controller; + struct musb_dma_channel aChannel[MUSB_HSDMA_CHANNELS]; + void *pDmaPrivate; + void __iomem *pCoreBase; + u8 bChannelCount; + u8 bmUsedChannels; + u8 irq; +}; + +static int dma_controller_start(struct dma_controller *c) +{ + /* nothing to do */ + return 0; +} + +static void dma_channel_release(struct dma_channel *pChannel); + +static int dma_controller_stop(struct dma_controller *c) +{ + struct musb_dma_controller *controller = + container_of(c, struct musb_dma_controller, Controller); + struct musb *musb = (struct musb *) controller->pDmaPrivate; + struct dma_channel *pChannel; + u8 bBit; + + if (controller->bmUsedChannels != 0) { + dev_err(musb->controller, + "Stopping DMA controller while channel active\n"); + + for (bBit = 0; bBit < MUSB_HSDMA_CHANNELS; bBit++) { + if (controller->bmUsedChannels & (1 << bBit)) { + pChannel = &controller->aChannel[bBit].Channel; + dma_channel_release(pChannel); + + if (!controller->bmUsedChannels) + break; + } + } + } + return 0; +} + +static struct dma_channel *dma_channel_allocate(struct dma_controller *c, + struct musb_hw_ep *hw_ep, u8 transmit) +{ + u8 bBit; + struct dma_channel *pChannel = NULL; + struct musb_dma_channel *pImplChannel = NULL; + struct musb_dma_controller *controller = + container_of(c, struct musb_dma_controller, Controller); + + for (bBit = 0; bBit < MUSB_HSDMA_CHANNELS; bBit++) { + if (!(controller->bmUsedChannels & (1 << bBit))) { + controller->bmUsedChannels |= (1 << bBit); + pImplChannel = &(controller->aChannel[bBit]); + pImplChannel->controller = controller; + pImplChannel->bIndex = bBit; + pImplChannel->epnum = hw_ep->epnum; + pImplChannel->transmit = transmit; + pChannel = &(pImplChannel->Channel); + pChannel->private_data = pImplChannel; + pChannel->status = MUSB_DMA_STATUS_FREE; + pChannel->max_len = 0x10000; + /* Tx => mode 1; Rx => mode 0 */ + pChannel->desired_mode = transmit; + pChannel->actual_len = 0; + break; + } + } + return pChannel; +} + +static void dma_channel_release(struct dma_channel *pChannel) +{ + struct musb_dma_channel *pImplChannel = + (struct musb_dma_channel *) pChannel->private_data; + + pChannel->actual_len = 0; + pImplChannel->dwStartAddress = 0; + pImplChannel->len = 0; + + pImplChannel->controller->bmUsedChannels &= + ~(1 << pImplChannel->bIndex); + + pChannel->status = MUSB_DMA_STATUS_UNKNOWN; +} + +static void configure_channel(struct dma_channel *pChannel, + u16 packet_sz, u8 mode, + dma_addr_t dma_addr, u32 len) +{ + struct musb_dma_channel *pImplChannel = + (struct musb_dma_channel *) pChannel->private_data; + struct musb_dma_controller *controller = pImplChannel->controller; + void __iomem *mbase = controller->pCoreBase; + u8 bChannel = pImplChannel->bIndex; + u16 csr = 0; + + DBG(4, "%p, pkt_sz %d, addr 0x%x, len %d, mode %d\n", + pChannel, packet_sz, dma_addr, len, mode); + + if (mode) { + csr |= 1 << MUSB_HSDMA_MODE1_SHIFT; + BUG_ON(len < packet_sz); + + if (packet_sz >= 64) { + csr |= MUSB_HSDMA_BURSTMODE_INCR16 + << MUSB_HSDMA_BURSTMODE_SHIFT; + } else if (packet_sz >= 32) { + csr |= MUSB_HSDMA_BURSTMODE_INCR8 + << MUSB_HSDMA_BURSTMODE_SHIFT; + } else if (packet_sz >= 16) { + csr |= MUSB_HSDMA_BURSTMODE_INCR4 + << MUSB_HSDMA_BURSTMODE_SHIFT; + } + } + + csr |= (pImplChannel->epnum << MUSB_HSDMA_ENDPOINT_SHIFT) + | (1 << MUSB_HSDMA_ENABLE_SHIFT) + | (1 << MUSB_HSDMA_IRQENABLE_SHIFT) + | (pImplChannel->transmit + ? (1 << MUSB_HSDMA_TRANSMIT_SHIFT) + : 0); + + /* address/count */ + musb_writel(mbase, + MUSB_HSDMA_CHANNEL_OFFSET(bChannel, MUSB_HSDMA_ADDRESS), + dma_addr); + musb_writel(mbase, + MUSB_HSDMA_CHANNEL_OFFSET(bChannel, MUSB_HSDMA_COUNT), + len); + + /* control (this should start things) */ + musb_writew(mbase, + MUSB_HSDMA_CHANNEL_OFFSET(bChannel, MUSB_HSDMA_CONTROL), + csr); +} + +static int dma_channel_program(struct dma_channel *pChannel, + u16 packet_sz, u8 mode, + dma_addr_t dma_addr, u32 len) +{ + struct musb_dma_channel *pImplChannel = + (struct musb_dma_channel *) pChannel->private_data; + + DBG(2, "ep%d-%s pkt_sz %d, dma_addr 0x%x length %d, mode %d\n", + pImplChannel->epnum, + pImplChannel->transmit ? "Tx" : "Rx", + packet_sz, dma_addr, len, mode); + + BUG_ON(pChannel->status == MUSB_DMA_STATUS_UNKNOWN || + pChannel->status == MUSB_DMA_STATUS_BUSY); + + pChannel->actual_len = 0; + pImplChannel->dwStartAddress = dma_addr; + pImplChannel->len = len; + pImplChannel->wMaxPacketSize = packet_sz; + pChannel->status = MUSB_DMA_STATUS_BUSY; + + if ((mode == 1) && (len >= packet_sz)) + configure_channel(pChannel, packet_sz, 1, dma_addr, len); + else + configure_channel(pChannel, packet_sz, 0, dma_addr, len); + + return true; +} + +static int dma_channel_abort(struct dma_channel *pChannel) +{ + struct musb_dma_channel *pImplChannel = + (struct musb_dma_channel *) pChannel->private_data; + u8 bChannel = pImplChannel->bIndex; + void __iomem *mbase = pImplChannel->controller->pCoreBase; + u16 csr; + + if (pChannel->status == MUSB_DMA_STATUS_BUSY) { + if (pImplChannel->transmit) { + + csr = musb_readw(mbase, + MUSB_EP_OFFSET(pImplChannel->epnum, + MUSB_TXCSR)); + csr &= ~(MUSB_TXCSR_AUTOSET | + MUSB_TXCSR_DMAENAB | + MUSB_TXCSR_DMAMODE); + musb_writew(mbase, + MUSB_EP_OFFSET(pImplChannel->epnum, + MUSB_TXCSR), + csr); + } else { + csr = musb_readw(mbase, + MUSB_EP_OFFSET(pImplChannel->epnum, + MUSB_RXCSR)); + csr &= ~(MUSB_RXCSR_AUTOCLEAR | + MUSB_RXCSR_DMAENAB | + MUSB_RXCSR_DMAMODE); + musb_writew(mbase, + MUSB_EP_OFFSET(pImplChannel->epnum, + MUSB_RXCSR), + csr); + } + + musb_writew(mbase, + MUSB_HSDMA_CHANNEL_OFFSET(bChannel, MUSB_HSDMA_CONTROL), + 0); + musb_writel(mbase, + MUSB_HSDMA_CHANNEL_OFFSET(bChannel, MUSB_HSDMA_ADDRESS), + 0); + musb_writel(mbase, + MUSB_HSDMA_CHANNEL_OFFSET(bChannel, MUSB_HSDMA_COUNT), + 0); + + pChannel->status = MUSB_DMA_STATUS_FREE; + } + return 0; +} + +static irqreturn_t dma_controller_irq(int irq, void *private_data) +{ + struct musb_dma_controller *controller = + (struct musb_dma_controller *)private_data; + struct musb_dma_channel *pImplChannel; + struct musb *musb = controller->pDmaPrivate; + void __iomem *mbase = controller->pCoreBase; + struct dma_channel *pChannel; + u8 bChannel; + u16 csr; + u32 dwAddress; + u8 int_hsdma; + irqreturn_t retval = IRQ_NONE; + unsigned long flags; + + spin_lock_irqsave(&musb->lock, flags); + + int_hsdma = musb_readb(mbase, MUSB_HSDMA_INTR); + if (!int_hsdma) + goto done; + + for (bChannel = 0; bChannel < MUSB_HSDMA_CHANNELS; bChannel++) { + if (int_hsdma & (1 << bChannel)) { + pImplChannel = (struct musb_dma_channel *) + &(controller->aChannel[bChannel]); + pChannel = &pImplChannel->Channel; + + csr = musb_readw(mbase, + MUSB_HSDMA_CHANNEL_OFFSET(bChannel, + MUSB_HSDMA_CONTROL)); + + if (csr & (1 << MUSB_HSDMA_BUSERROR_SHIFT)) + pImplChannel->Channel.status = + MUSB_DMA_STATUS_BUS_ABORT; + else { + u8 devctl; + + dwAddress = musb_readl(mbase, + MUSB_HSDMA_CHANNEL_OFFSET( + bChannel, + MUSB_HSDMA_ADDRESS)); + pChannel->actual_len = dwAddress + - pImplChannel->dwStartAddress; + + DBG(2, "ch %p, 0x%x -> 0x%x (%d / %d) %s\n", + pChannel, pImplChannel->dwStartAddress, + dwAddress, pChannel->actual_len, + pImplChannel->len, + (pChannel->actual_len + < pImplChannel->len) ? + "=> reconfig 0" : "=> complete"); + + devctl = musb_readb(mbase, MUSB_DEVCTL); + + pChannel->status = MUSB_DMA_STATUS_FREE; + + /* completed */ + if ((devctl & MUSB_DEVCTL_HM) + && (pImplChannel->transmit) + && ((pChannel->desired_mode == 0) + || (pChannel->actual_len & + (pImplChannel->wMaxPacketSize - 1))) + ) { + /* Send out the packet */ + musb_ep_select(mbase, + pImplChannel->epnum); + musb_writew(mbase, MUSB_EP_OFFSET( + pImplChannel->epnum, + MUSB_TXCSR), + MUSB_TXCSR_TXPKTRDY); + } else + musb_dma_completion( + musb, + pImplChannel->epnum, + pImplChannel->transmit); + } + } + } + retval = IRQ_HANDLED; +done: + spin_unlock_irqrestore(&musb->lock, flags); + return retval; +} + +void dma_controller_destroy(struct dma_controller *c) +{ + struct musb_dma_controller *controller; + + controller = container_of(c, struct musb_dma_controller, Controller); + if (!controller) + return; + + if (controller->irq) + free_irq(controller->irq, c); + + kfree(controller); +} + +struct dma_controller *__init +dma_controller_create(struct musb *musb, void __iomem *pCoreBase) +{ + struct musb_dma_controller *controller; + struct device *dev = musb->controller; + struct platform_device *pdev = to_platform_device(dev); + int irq = platform_get_irq(pdev, 1); + + if (irq == 0) { + dev_err(dev, "No DMA interrupt line!\n"); + return NULL; + } + + controller = kzalloc(sizeof(struct musb_dma_controller), GFP_KERNEL); + if (!controller) + return NULL; + + controller->bChannelCount = MUSB_HSDMA_CHANNELS; + controller->pDmaPrivate = musb; + controller->pCoreBase = pCoreBase; + + controller->Controller.start = dma_controller_start; + controller->Controller.stop = dma_controller_stop; + controller->Controller.channel_alloc = dma_channel_allocate; + controller->Controller.channel_release = dma_channel_release; + controller->Controller.channel_program = dma_channel_program; + controller->Controller.channel_abort = dma_channel_abort; + + if (request_irq(irq, dma_controller_irq, IRQF_DISABLED, + musb->controller->bus_id, &controller->Controller)) { + dev_err(dev, "request_irq %d failed!\n", irq); + dma_controller_destroy(&controller->Controller); + return NULL; + } + + controller->irq = irq; + + return &controller->Controller; +} diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c new file mode 100644 index 00000000000..298b22e6ad0 --- /dev/null +++ b/drivers/usb/musb/omap2430.c @@ -0,0 +1,324 @@ +/* + * Copyright (C) 2005-2007 by Texas Instruments + * Some code has been taken from tusb6010.c + * Copyrights for that are attributable to: + * Copyright (C) 2006 Nokia Corporation + * Jarkko Nikula + * Tony Lindgren + * + * This file is part of the Inventra Controller Driver for Linux. + * + * The Inventra Controller Driver for Linux is free software; you + * can redistribute it and/or modify it under the terms of the GNU + * General Public License version 2 as published by the Free Software + * Foundation. + * + * The Inventra Controller Driver for Linux is distributed in + * the hope that it will be useful, but WITHOUT ANY WARRANTY; + * without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public + * License for more details. + * + * You should have received a copy of the GNU General Public License + * along with The Inventra Controller Driver for Linux ; if not, + * write to the Free Software Foundation, Inc., 59 Temple Place, + * Suite 330, Boston, MA 02111-1307 USA + * + */ +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include "musb_core.h" +#include "omap2430.h" + +#ifdef CONFIG_ARCH_OMAP3430 +#define get_cpu_rev() 2 +#endif + +#define MUSB_TIMEOUT_A_WAIT_BCON 1100 + +static struct timer_list musb_idle_timer; + +static void musb_do_idle(unsigned long _musb) +{ + struct musb *musb = (void *)_musb; + unsigned long flags; + u8 power; + u8 devctl; + + devctl = musb_readb(musb->mregs, MUSB_DEVCTL); + + spin_lock_irqsave(&musb->lock, flags); + + switch (musb->xceiv.state) { + case OTG_STATE_A_WAIT_BCON: + devctl &= ~MUSB_DEVCTL_SESSION; + musb_writeb(musb->mregs, MUSB_DEVCTL, devctl); + + devctl = musb_readb(musb->mregs, MUSB_DEVCTL); + if (devctl & MUSB_DEVCTL_BDEVICE) { + musb->xceiv.state = OTG_STATE_B_IDLE; + MUSB_DEV_MODE(musb); + } else { + musb->xceiv.state = OTG_STATE_A_IDLE; + MUSB_HST_MODE(musb); + } + break; +#ifdef CONFIG_USB_MUSB_HDRC_HCD + case OTG_STATE_A_SUSPEND: + /* finish RESUME signaling? */ + if (musb->port1_status & MUSB_PORT_STAT_RESUME) { + power = musb_readb(musb->mregs, MUSB_POWER); + power &= ~MUSB_POWER_RESUME; + DBG(1, "root port resume stopped, power %02x\n", power); + musb_writeb(musb->mregs, MUSB_POWER, power); + musb->is_active = 1; + musb->port1_status &= ~(USB_PORT_STAT_SUSPEND + | MUSB_PORT_STAT_RESUME); + musb->port1_status |= USB_PORT_STAT_C_SUSPEND << 16; + usb_hcd_poll_rh_status(musb_to_hcd(musb)); + /* NOTE: it might really be A_WAIT_BCON ... */ + musb->xceiv.state = OTG_STATE_A_HOST; + } + break; +#endif +#ifdef CONFIG_USB_MUSB_HDRC_HCD + case OTG_STATE_A_HOST: + devctl = musb_readb(musb->mregs, MUSB_DEVCTL); + if (devctl & MUSB_DEVCTL_BDEVICE) + musb->xceiv.state = OTG_STATE_B_IDLE; + else + musb->xceiv.state = OTG_STATE_A_WAIT_BCON; +#endif + default: + break; + } + spin_unlock_irqrestore(&musb->lock, flags); +} + + +void musb_platform_try_idle(struct musb *musb, unsigned long timeout) +{ + unsigned long default_timeout = jiffies + msecs_to_jiffies(3); + static unsigned long last_timer; + + if (timeout == 0) + timeout = default_timeout; + + /* Never idle if active, or when VBUS timeout is not set as host */ + if (musb->is_active || ((musb->a_wait_bcon == 0) + && (musb->xceiv.state == OTG_STATE_A_WAIT_BCON))) { + DBG(4, "%s active, deleting timer\n", otg_state_string(musb)); + del_timer(&musb_idle_timer); + last_timer = jiffies; + return; + } + + if (time_after(last_timer, timeout)) { + if (!timer_pending(&musb_idle_timer)) + last_timer = timeout; + else { + DBG(4, "Longer idle timer already pending, ignoring\n"); + return; + } + } + last_timer = timeout; + + DBG(4, "%s inactive, for idle timer for %lu ms\n", + otg_state_string(musb), + (unsigned long)jiffies_to_msecs(timeout - jiffies)); + mod_timer(&musb_idle_timer, timeout); +} + +void musb_platform_enable(struct musb *musb) +{ +} +void musb_platform_disable(struct musb *musb) +{ +} +static void omap_vbus_power(struct musb *musb, int is_on, int sleeping) +{ +} + +static void omap_set_vbus(struct musb *musb, int is_on) +{ + u8 devctl; + /* HDRC controls CPEN, but beware current surges during device + * connect. They can trigger transient overcurrent conditions + * that must be ignored. + */ + + devctl = musb_readb(musb->mregs, MUSB_DEVCTL); + + if (is_on) { + musb->is_active = 1; + musb->xceiv.default_a = 1; + musb->xceiv.state = OTG_STATE_A_WAIT_VRISE; + devctl |= MUSB_DEVCTL_SESSION; + + MUSB_HST_MODE(musb); + } else { + musb->is_active = 0; + + /* NOTE: we're skipping A_WAIT_VFALL -> A_IDLE and + * jumping right to B_IDLE... + */ + + musb->xceiv.default_a = 0; + musb->xceiv.state = OTG_STATE_B_IDLE; + devctl &= ~MUSB_DEVCTL_SESSION; + + MUSB_DEV_MODE(musb); + } + musb_writeb(musb->mregs, MUSB_DEVCTL, devctl); + + DBG(1, "VBUS %s, devctl %02x " + /* otg %3x conf %08x prcm %08x */ "\n", + otg_state_string(musb), + musb_readb(musb->mregs, MUSB_DEVCTL)); +} +static int omap_set_power(struct otg_transceiver *x, unsigned mA) +{ + return 0; +} + +static int musb_platform_resume(struct musb *musb); + +void musb_platform_set_mode(struct musb *musb, u8 musb_mode) +{ + u8 devctl = musb_readb(musb->mregs, MUSB_DEVCTL); + + devctl |= MUSB_DEVCTL_SESSION; + musb_writeb(musb->mregs, MUSB_DEVCTL, devctl); + + switch (musb_mode) { + case MUSB_HOST: + otg_set_host(&musb->xceiv, musb->xceiv.host); + break; + case MUSB_PERIPHERAL: + otg_set_peripheral(&musb->xceiv, musb->xceiv.gadget); + break; + case MUSB_OTG: + break; + } +} + +int __init musb_platform_init(struct musb *musb) +{ + u32 l; + +#if defined(CONFIG_ARCH_OMAP2430) + omap_cfg_reg(AE5_2430_USB0HS_STP); +#endif + + musb_platform_resume(musb); + + l = omap_readl(OTG_SYSCONFIG); + l &= ~ENABLEWAKEUP; /* disable wakeup */ + l &= ~NOSTDBY; /* remove possible nostdby */ + l |= SMARTSTDBY; /* enable smart standby */ + l &= ~AUTOIDLE; /* disable auto idle */ + l &= ~NOIDLE; /* remove possible noidle */ + l |= SMARTIDLE; /* enable smart idle */ + l |= AUTOIDLE; /* enable auto idle */ + omap_writel(l, OTG_SYSCONFIG); + + l = omap_readl(OTG_INTERFSEL); + l |= ULPI_12PIN; + omap_writel(l, OTG_INTERFSEL); + + pr_debug("HS USB OTG: revision 0x%x, sysconfig 0x%02x, " + "sysstatus 0x%x, intrfsel 0x%x, simenable 0x%x\n", + omap_readl(OTG_REVISION), omap_readl(OTG_SYSCONFIG), + omap_readl(OTG_SYSSTATUS), omap_readl(OTG_INTERFSEL), + omap_readl(OTG_SIMENABLE)); + + omap_vbus_power(musb, musb->board_mode == MUSB_HOST, 1); + + if (is_host_enabled(musb)) + musb->board_set_vbus = omap_set_vbus; + if (is_peripheral_enabled(musb)) + musb->xceiv.set_power = omap_set_power; + musb->a_wait_bcon = MUSB_TIMEOUT_A_WAIT_BCON; + + setup_timer(&musb_idle_timer, musb_do_idle, (unsigned long) musb); + + return 0; +} + +int musb_platform_suspend(struct musb *musb) +{ + u32 l; + + if (!musb->clock) + return 0; + + /* in any role */ + l = omap_readl(OTG_FORCESTDBY); + l |= ENABLEFORCE; /* enable MSTANDBY */ + omap_writel(l, OTG_FORCESTDBY); + + l = omap_readl(OTG_SYSCONFIG); + l |= ENABLEWAKEUP; /* enable wakeup */ + omap_writel(l, OTG_SYSCONFIG); + + if (musb->xceiv.set_suspend) + musb->xceiv.set_suspend(&musb->xceiv, 1); + + if (musb->set_clock) + musb->set_clock(musb->clock, 0); + else + clk_disable(musb->clock); + + return 0; +} + +static int musb_platform_resume(struct musb *musb) +{ + u32 l; + + if (!musb->clock) + return 0; + + if (musb->xceiv.set_suspend) + musb->xceiv.set_suspend(&musb->xceiv, 0); + + if (musb->set_clock) + musb->set_clock(musb->clock, 1); + else + clk_enable(musb->clock); + + l = omap_readl(OTG_SYSCONFIG); + l &= ~ENABLEWAKEUP; /* disable wakeup */ + omap_writel(l, OTG_SYSCONFIG); + + l = omap_readl(OTG_FORCESTDBY); + l &= ~ENABLEFORCE; /* disable MSTANDBY */ + omap_writel(l, OTG_FORCESTDBY); + + return 0; +} + + +int musb_platform_exit(struct musb *musb) +{ + + omap_vbus_power(musb, 0 /*off*/, 1); + + musb_platform_suspend(musb); + + clk_put(musb->clock); + musb->clock = 0; + + return 0; +} diff --git a/drivers/usb/musb/omap2430.h b/drivers/usb/musb/omap2430.h new file mode 100644 index 00000000000..786a62071f7 --- /dev/null +++ b/drivers/usb/musb/omap2430.h @@ -0,0 +1,56 @@ +/* + * Copyright (C) 2005-2006 by Texas Instruments + * + * The Inventra Controller Driver for Linux is free software; you + * can redistribute it and/or modify it under the terms of the GNU + * General Public License version 2 as published by the Free Software + * Foundation. + */ + +#ifndef __MUSB_OMAP243X_H__ +#define __MUSB_OMAP243X_H__ + +#if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3430) +#include +#include + +/* + * OMAP2430-specific definitions + */ + +#define MENTOR_BASE_OFFSET 0 +#if defined(CONFIG_ARCH_OMAP2430) +#define OMAP_HSOTG_BASE (OMAP243X_HS_BASE) +#elif defined(CONFIG_ARCH_OMAP3430) +#define OMAP_HSOTG_BASE (OMAP34XX_HSUSB_OTG_BASE) +#endif +#define OMAP_HSOTG(offset) (OMAP_HSOTG_BASE + 0x400 + (offset)) +#define OTG_REVISION OMAP_HSOTG(0x0) +#define OTG_SYSCONFIG OMAP_HSOTG(0x4) +# define MIDLEMODE 12 /* bit position */ +# define FORCESTDBY (0 << MIDLEMODE) +# define NOSTDBY (1 << MIDLEMODE) +# define SMARTSTDBY (2 << MIDLEMODE) +# define SIDLEMODE 3 /* bit position */ +# define FORCEIDLE (0 << SIDLEMODE) +# define NOIDLE (1 << SIDLEMODE) +# define SMARTIDLE (2 << SIDLEMODE) +# define ENABLEWAKEUP (1 << 2) +# define SOFTRST (1 << 1) +# define AUTOIDLE (1 << 0) +#define OTG_SYSSTATUS OMAP_HSOTG(0x8) +# define RESETDONE (1 << 0) +#define OTG_INTERFSEL OMAP_HSOTG(0xc) +# define EXTCP (1 << 2) +# define PHYSEL 0 /* bit position */ +# define UTMI_8BIT (0 << PHYSEL) +# define ULPI_12PIN (1 << PHYSEL) +# define ULPI_8PIN (2 << PHYSEL) +#define OTG_SIMENABLE OMAP_HSOTG(0x10) +# define TM1 (1 << 0) +#define OTG_FORCESTDBY OMAP_HSOTG(0x14) +# define ENABLEFORCE (1 << 0) + +#endif /* CONFIG_ARCH_OMAP2430 */ + +#endif /* __MUSB_OMAP243X_H__ */ diff --git a/drivers/usb/musb/tusb6010.c b/drivers/usb/musb/tusb6010.c new file mode 100644 index 00000000000..b73b036f3d7 --- /dev/null +++ b/drivers/usb/musb/tusb6010.c @@ -0,0 +1,1151 @@ +/* + * TUSB6010 USB 2.0 OTG Dual Role controller + * + * Copyright (C) 2006 Nokia Corporation + * Jarkko Nikula + * Tony Lindgren + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Notes: + * - Driver assumes that interface to external host (main CPU) is + * configured for NOR FLASH interface instead of VLYNQ serial + * interface. + */ + +#include +#include +#include +#include +#include +#include +#include + +#include "musb_core.h" + +static void tusb_source_power(struct musb *musb, int is_on); + +#define TUSB_REV_MAJOR(reg_val) ((reg_val >> 4) & 0xf) +#define TUSB_REV_MINOR(reg_val) (reg_val & 0xf) + +/* + * Checks the revision. We need to use the DMA register as 3.0 does not + * have correct versions for TUSB_PRCM_REV or TUSB_INT_CTRL_REV. + */ +u8 tusb_get_revision(struct musb *musb) +{ + void __iomem *tbase = musb->ctrl_base; + u32 die_id; + u8 rev; + + rev = musb_readl(tbase, TUSB_DMA_CTRL_REV) & 0xff; + if (TUSB_REV_MAJOR(rev) == 3) { + die_id = TUSB_DIDR1_HI_CHIP_REV(musb_readl(tbase, + TUSB_DIDR1_HI)); + if (die_id >= TUSB_DIDR1_HI_REV_31) + rev |= 1; + } + + return rev; +} + +static int __init tusb_print_revision(struct musb *musb) +{ + void __iomem *tbase = musb->ctrl_base; + u8 rev; + + rev = tusb_get_revision(musb); + + pr_info("tusb: %s%i.%i %s%i.%i %s%i.%i %s%i.%i %s%i %s%i.%i\n", + "prcm", + TUSB_REV_MAJOR(musb_readl(tbase, TUSB_PRCM_REV)), + TUSB_REV_MINOR(musb_readl(tbase, TUSB_PRCM_REV)), + "int", + TUSB_REV_MAJOR(musb_readl(tbase, TUSB_INT_CTRL_REV)), + TUSB_REV_MINOR(musb_readl(tbase, TUSB_INT_CTRL_REV)), + "gpio", + TUSB_REV_MAJOR(musb_readl(tbase, TUSB_GPIO_REV)), + TUSB_REV_MINOR(musb_readl(tbase, TUSB_GPIO_REV)), + "dma", + TUSB_REV_MAJOR(musb_readl(tbase, TUSB_DMA_CTRL_REV)), + TUSB_REV_MINOR(musb_readl(tbase, TUSB_DMA_CTRL_REV)), + "dieid", + TUSB_DIDR1_HI_CHIP_REV(musb_readl(tbase, TUSB_DIDR1_HI)), + "rev", + TUSB_REV_MAJOR(rev), TUSB_REV_MINOR(rev)); + + return tusb_get_revision(musb); +} + +#define WBUS_QUIRK_MASK (TUSB_PHY_OTG_CTRL_TESTM2 | TUSB_PHY_OTG_CTRL_TESTM1 \ + | TUSB_PHY_OTG_CTRL_TESTM0) + +/* + * Workaround for spontaneous WBUS wake-up issue #2 for tusb3.0. + * Disables power detection in PHY for the duration of idle. + */ +static void tusb_wbus_quirk(struct musb *musb, int enabled) +{ + void __iomem *tbase = musb->ctrl_base; + static u32 phy_otg_ctrl, phy_otg_ena; + u32 tmp; + + if (enabled) { + phy_otg_ctrl = musb_readl(tbase, TUSB_PHY_OTG_CTRL); + phy_otg_ena = musb_readl(tbase, TUSB_PHY_OTG_CTRL_ENABLE); + tmp = TUSB_PHY_OTG_CTRL_WRPROTECT + | phy_otg_ena | WBUS_QUIRK_MASK; + musb_writel(tbase, TUSB_PHY_OTG_CTRL, tmp); + tmp = phy_otg_ena & ~WBUS_QUIRK_MASK; + tmp |= TUSB_PHY_OTG_CTRL_WRPROTECT | TUSB_PHY_OTG_CTRL_TESTM2; + musb_writel(tbase, TUSB_PHY_OTG_CTRL_ENABLE, tmp); + DBG(2, "Enabled tusb wbus quirk ctrl %08x ena %08x\n", + musb_readl(tbase, TUSB_PHY_OTG_CTRL), + musb_readl(tbase, TUSB_PHY_OTG_CTRL_ENABLE)); + } else if (musb_readl(tbase, TUSB_PHY_OTG_CTRL_ENABLE) + & TUSB_PHY_OTG_CTRL_TESTM2) { + tmp = TUSB_PHY_OTG_CTRL_WRPROTECT | phy_otg_ctrl; + musb_writel(tbase, TUSB_PHY_OTG_CTRL, tmp); + tmp = TUSB_PHY_OTG_CTRL_WRPROTECT | phy_otg_ena; + musb_writel(tbase, TUSB_PHY_OTG_CTRL_ENABLE, tmp); + DBG(2, "Disabled tusb wbus quirk ctrl %08x ena %08x\n", + musb_readl(tbase, TUSB_PHY_OTG_CTRL), + musb_readl(tbase, TUSB_PHY_OTG_CTRL_ENABLE)); + phy_otg_ctrl = 0; + phy_otg_ena = 0; + } +} + +/* + * TUSB 6010 may use a parallel bus that doesn't support byte ops; + * so both loading and unloading FIFOs need explicit byte counts. + */ + +static inline void +tusb_fifo_write_unaligned(void __iomem *fifo, const u8 *buf, u16 len) +{ + u32 val; + int i; + + if (len > 4) { + for (i = 0; i < (len >> 2); i++) { + memcpy(&val, buf, 4); + musb_writel(fifo, 0, val); + buf += 4; + } + len %= 4; + } + if (len > 0) { + /* Write the rest 1 - 3 bytes to FIFO */ + memcpy(&val, buf, len); + musb_writel(fifo, 0, val); + } +} + +static inline void tusb_fifo_read_unaligned(void __iomem *fifo, + void __iomem *buf, u16 len) +{ + u32 val; + int i; + + if (len > 4) { + for (i = 0; i < (len >> 2); i++) { + val = musb_readl(fifo, 0); + memcpy(buf, &val, 4); + buf += 4; + } + len %= 4; + } + if (len > 0) { + /* Read the rest 1 - 3 bytes from FIFO */ + val = musb_readl(fifo, 0); + memcpy(buf, &val, len); + } +} + +void musb_write_fifo(struct musb_hw_ep *hw_ep, u16 len, const u8 *buf) +{ + void __iomem *ep_conf = hw_ep->conf; + void __iomem *fifo = hw_ep->fifo; + u8 epnum = hw_ep->epnum; + + prefetch(buf); + + DBG(4, "%cX ep%d fifo %p count %d buf %p\n", + 'T', epnum, fifo, len, buf); + + if (epnum) + musb_writel(ep_conf, TUSB_EP_TX_OFFSET, + TUSB_EP_CONFIG_XFR_SIZE(len)); + else + musb_writel(ep_conf, 0, TUSB_EP0_CONFIG_DIR_TX | + TUSB_EP0_CONFIG_XFR_SIZE(len)); + + if (likely((0x01 & (unsigned long) buf) == 0)) { + + /* Best case is 32bit-aligned destination address */ + if ((0x02 & (unsigned long) buf) == 0) { + if (len >= 4) { + writesl(fifo, buf, len >> 2); + buf += (len & ~0x03); + len &= 0x03; + } + } else { + if (len >= 2) { + u32 val; + int i; + + /* Cannot use writesw, fifo is 32-bit */ + for (i = 0; i < (len >> 2); i++) { + val = (u32)(*(u16 *)buf); + buf += 2; + val |= (*(u16 *)buf) << 16; + buf += 2; + musb_writel(fifo, 0, val); + } + len &= 0x03; + } + } + } + + if (len > 0) + tusb_fifo_write_unaligned(fifo, buf, len); +} + +void musb_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *buf) +{ + void __iomem *ep_conf = hw_ep->conf; + void __iomem *fifo = hw_ep->fifo; + u8 epnum = hw_ep->epnum; + + DBG(4, "%cX ep%d fifo %p count %d buf %p\n", + 'R', epnum, fifo, len, buf); + + if (epnum) + musb_writel(ep_conf, TUSB_EP_RX_OFFSET, + TUSB_EP_CONFIG_XFR_SIZE(len)); + else + musb_writel(ep_conf, 0, TUSB_EP0_CONFIG_XFR_SIZE(len)); + + if (likely((0x01 & (unsigned long) buf) == 0)) { + + /* Best case is 32bit-aligned destination address */ + if ((0x02 & (unsigned long) buf) == 0) { + if (len >= 4) { + readsl(fifo, buf, len >> 2); + buf += (len & ~0x03); + len &= 0x03; + } + } else { + if (len >= 2) { + u32 val; + int i; + + /* Cannot use readsw, fifo is 32-bit */ + for (i = 0; i < (len >> 2); i++) { + val = musb_readl(fifo, 0); + *(u16 *)buf = (u16)(val & 0xffff); + buf += 2; + *(u16 *)buf = (u16)(val >> 16); + buf += 2; + } + len &= 0x03; + } + } + } + + if (len > 0) + tusb_fifo_read_unaligned(fifo, buf, len); +} + +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + +/* This is used by gadget drivers, and OTG transceiver logic, allowing + * at most mA current to be drawn from VBUS during a Default-B session + * (that is, while VBUS exceeds 4.4V). In Default-A (including pure host + * mode), or low power Default-B sessions, something else supplies power. + * Caller must take care of locking. + */ +static int tusb_draw_power(struct otg_transceiver *x, unsigned mA) +{ + struct musb *musb = container_of(x, struct musb, xceiv); + void __iomem *tbase = musb->ctrl_base; + u32 reg; + + /* + * Keep clock active when enabled. Note that this is not tied to + * drawing VBUS, as with OTG mA can be less than musb->min_power. + */ + if (musb->set_clock) { + if (mA) + musb->set_clock(musb->clock, 1); + else + musb->set_clock(musb->clock, 0); + } + + /* tps65030 seems to consume max 100mA, with maybe 60mA available + * (measured on one board) for things other than tps and tusb. + * + * Boards sharing the CPU clock with CLKIN will need to prevent + * certain idle sleep states while the USB link is active. + * + * REVISIT we could use VBUS to supply only _one_ of { 1.5V, 3.3V }. + * The actual current usage would be very board-specific. For now, + * it's simpler to just use an aggregate (also board-specific). + */ + if (x->default_a || mA < (musb->min_power << 1)) + mA = 0; + + reg = musb_readl(tbase, TUSB_PRCM_MNGMT); + if (mA) { + musb->is_bus_powered = 1; + reg |= TUSB_PRCM_MNGMT_15_SW_EN | TUSB_PRCM_MNGMT_33_SW_EN; + } else { + musb->is_bus_powered = 0; + reg &= ~(TUSB_PRCM_MNGMT_15_SW_EN | TUSB_PRCM_MNGMT_33_SW_EN); + } + musb_writel(tbase, TUSB_PRCM_MNGMT, reg); + + DBG(2, "draw max %d mA VBUS\n", mA); + return 0; +} + +#else +#define tusb_draw_power NULL +#endif + +/* workaround for issue 13: change clock during chip idle + * (to be fixed in rev3 silicon) ... symptoms include disconnect + * or looping suspend/resume cycles + */ +static void tusb_set_clock_source(struct musb *musb, unsigned mode) +{ + void __iomem *tbase = musb->ctrl_base; + u32 reg; + + reg = musb_readl(tbase, TUSB_PRCM_CONF); + reg &= ~TUSB_PRCM_CONF_SYS_CLKSEL(0x3); + + /* 0 = refclk (clkin, XI) + * 1 = PHY 60 MHz (internal PLL) + * 2 = not supported + * 3 = what? + */ + if (mode > 0) + reg |= TUSB_PRCM_CONF_SYS_CLKSEL(mode & 0x3); + + musb_writel(tbase, TUSB_PRCM_CONF, reg); + + /* FIXME tusb6010_platform_retime(mode == 0); */ +} + +/* + * Idle TUSB6010 until next wake-up event; NOR access always wakes. + * Other code ensures that we idle unless we're connected _and_ the + * USB link is not suspended ... and tells us the relevant wakeup + * events. SW_EN for voltage is handled separately. + */ +void tusb_allow_idle(struct musb *musb, u32 wakeup_enables) +{ + void __iomem *tbase = musb->ctrl_base; + u32 reg; + + if ((wakeup_enables & TUSB_PRCM_WBUS) + && (tusb_get_revision(musb) == TUSB_REV_30)) + tusb_wbus_quirk(musb, 1); + + tusb_set_clock_source(musb, 0); + + wakeup_enables |= TUSB_PRCM_WNORCS; + musb_writel(tbase, TUSB_PRCM_WAKEUP_MASK, ~wakeup_enables); + + /* REVISIT writeup of WID implies that if WID set and ID is grounded, + * TUSB_PHY_OTG_CTRL.TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP must be cleared. + * Presumably that's mostly to save power, hence WID is immaterial ... + */ + + reg = musb_readl(tbase, TUSB_PRCM_MNGMT); + /* issue 4: when driving vbus, use hipower (vbus_det) comparator */ + if (is_host_active(musb)) { + reg |= TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN; + reg &= ~TUSB_PRCM_MNGMT_OTG_SESS_END_EN; + } else { + reg |= TUSB_PRCM_MNGMT_OTG_SESS_END_EN; + reg &= ~TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN; + } + reg |= TUSB_PRCM_MNGMT_PM_IDLE | TUSB_PRCM_MNGMT_DEV_IDLE; + musb_writel(tbase, TUSB_PRCM_MNGMT, reg); + + DBG(6, "idle, wake on %02x\n", wakeup_enables); +} + +/* + * Updates cable VBUS status. Caller must take care of locking. + */ +int musb_platform_get_vbus_status(struct musb *musb) +{ + void __iomem *tbase = musb->ctrl_base; + u32 otg_stat, prcm_mngmt; + int ret = 0; + + otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT); + prcm_mngmt = musb_readl(tbase, TUSB_PRCM_MNGMT); + + /* Temporarily enable VBUS detection if it was disabled for + * suspend mode. Unless it's enabled otg_stat and devctl will + * not show correct VBUS state. + */ + if (!(prcm_mngmt & TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN)) { + u32 tmp = prcm_mngmt; + tmp |= TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN; + musb_writel(tbase, TUSB_PRCM_MNGMT, tmp); + otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT); + musb_writel(tbase, TUSB_PRCM_MNGMT, prcm_mngmt); + } + + if (otg_stat & TUSB_DEV_OTG_STAT_VBUS_VALID) + ret = 1; + + return ret; +} + +static struct timer_list musb_idle_timer; + +static void musb_do_idle(unsigned long _musb) +{ + struct musb *musb = (void *)_musb; + unsigned long flags; + + spin_lock_irqsave(&musb->lock, flags); + + switch (musb->xceiv.state) { + case OTG_STATE_A_WAIT_BCON: + if ((musb->a_wait_bcon != 0) + && (musb->idle_timeout == 0 + || time_after(jiffies, musb->idle_timeout))) { + DBG(4, "Nothing connected %s, turning off VBUS\n", + otg_state_string(musb)); + } + /* FALLTHROUGH */ + case OTG_STATE_A_IDLE: + tusb_source_power(musb, 0); + default: + break; + } + + if (!musb->is_active) { + u32 wakeups; + + /* wait until khubd handles port change status */ + if (is_host_active(musb) && (musb->port1_status >> 16)) + goto done; + +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + if (is_peripheral_enabled(musb) && !musb->gadget_driver) + wakeups = 0; + else { + wakeups = TUSB_PRCM_WHOSTDISCON + | TUSB_PRCM_WBUS + | TUSB_PRCM_WVBUS; + if (is_otg_enabled(musb)) + wakeups |= TUSB_PRCM_WID; + } +#else + wakeups = TUSB_PRCM_WHOSTDISCON | TUSB_PRCM_WBUS; +#endif + tusb_allow_idle(musb, wakeups); + } +done: + spin_unlock_irqrestore(&musb->lock, flags); +} + +/* + * Maybe put TUSB6010 into idle mode mode depending on USB link status, + * like "disconnected" or "suspended". We'll be woken out of it by + * connect, resume, or disconnect. + * + * Needs to be called as the last function everywhere where there is + * register access to TUSB6010 because of NOR flash wake-up. + * Caller should own controller spinlock. + * + * Delay because peripheral enables D+ pullup 3msec after SE0, and + * we don't want to treat that full speed J as a wakeup event. + * ... peripherals must draw only suspend current after 10 msec. + */ +void musb_platform_try_idle(struct musb *musb, unsigned long timeout) +{ + unsigned long default_timeout = jiffies + msecs_to_jiffies(3); + static unsigned long last_timer; + + if (timeout == 0) + timeout = default_timeout; + + /* Never idle if active, or when VBUS timeout is not set as host */ + if (musb->is_active || ((musb->a_wait_bcon == 0) + && (musb->xceiv.state == OTG_STATE_A_WAIT_BCON))) { + DBG(4, "%s active, deleting timer\n", otg_state_string(musb)); + del_timer(&musb_idle_timer); + last_timer = jiffies; + return; + } + + if (time_after(last_timer, timeout)) { + if (!timer_pending(&musb_idle_timer)) + last_timer = timeout; + else { + DBG(4, "Longer idle timer already pending, ignoring\n"); + return; + } + } + last_timer = timeout; + + DBG(4, "%s inactive, for idle timer for %lu ms\n", + otg_state_string(musb), + (unsigned long)jiffies_to_msecs(timeout - jiffies)); + mod_timer(&musb_idle_timer, timeout); +} + +/* ticks of 60 MHz clock */ +#define DEVCLOCK 60000000 +#define OTG_TIMER_MS(msecs) ((msecs) \ + ? (TUSB_DEV_OTG_TIMER_VAL((DEVCLOCK/1000)*(msecs)) \ + | TUSB_DEV_OTG_TIMER_ENABLE) \ + : 0) + +static void tusb_source_power(struct musb *musb, int is_on) +{ + void __iomem *tbase = musb->ctrl_base; + u32 conf, prcm, timer; + u8 devctl; + + /* HDRC controls CPEN, but beware current surges during device + * connect. They can trigger transient overcurrent conditions + * that must be ignored. + */ + + prcm = musb_readl(tbase, TUSB_PRCM_MNGMT); + conf = musb_readl(tbase, TUSB_DEV_CONF); + devctl = musb_readb(musb->mregs, MUSB_DEVCTL); + + if (is_on) { + if (musb->set_clock) + musb->set_clock(musb->clock, 1); + timer = OTG_TIMER_MS(OTG_TIME_A_WAIT_VRISE); + musb->xceiv.default_a = 1; + musb->xceiv.state = OTG_STATE_A_WAIT_VRISE; + devctl |= MUSB_DEVCTL_SESSION; + + conf |= TUSB_DEV_CONF_USB_HOST_MODE; + MUSB_HST_MODE(musb); + } else { + u32 otg_stat; + + timer = 0; + + /* If ID pin is grounded, we want to be a_idle */ + otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT); + if (!(otg_stat & TUSB_DEV_OTG_STAT_ID_STATUS)) { + switch (musb->xceiv.state) { + case OTG_STATE_A_WAIT_VRISE: + case OTG_STATE_A_WAIT_BCON: + musb->xceiv.state = OTG_STATE_A_WAIT_VFALL; + break; + case OTG_STATE_A_WAIT_VFALL: + musb->xceiv.state = OTG_STATE_A_IDLE; + break; + default: + musb->xceiv.state = OTG_STATE_A_IDLE; + } + musb->is_active = 0; + musb->xceiv.default_a = 1; + MUSB_HST_MODE(musb); + } else { + musb->is_active = 0; + musb->xceiv.default_a = 0; + musb->xceiv.state = OTG_STATE_B_IDLE; + MUSB_DEV_MODE(musb); + } + + devctl &= ~MUSB_DEVCTL_SESSION; + conf &= ~TUSB_DEV_CONF_USB_HOST_MODE; + if (musb->set_clock) + musb->set_clock(musb->clock, 0); + } + prcm &= ~(TUSB_PRCM_MNGMT_15_SW_EN | TUSB_PRCM_MNGMT_33_SW_EN); + + musb_writel(tbase, TUSB_PRCM_MNGMT, prcm); + musb_writel(tbase, TUSB_DEV_OTG_TIMER, timer); + musb_writel(tbase, TUSB_DEV_CONF, conf); + musb_writeb(musb->mregs, MUSB_DEVCTL, devctl); + + DBG(1, "VBUS %s, devctl %02x otg %3x conf %08x prcm %08x\n", + otg_state_string(musb), + musb_readb(musb->mregs, MUSB_DEVCTL), + musb_readl(tbase, TUSB_DEV_OTG_STAT), + conf, prcm); +} + +/* + * Sets the mode to OTG, peripheral or host by changing the ID detection. + * Caller must take care of locking. + * + * Note that if a mini-A cable is plugged in the ID line will stay down as + * the weak ID pull-up is not able to pull the ID up. + * + * REVISIT: It would be possible to add support for changing between host + * and peripheral modes in non-OTG configurations by reconfiguring hardware + * and then setting musb->board_mode. For now, only support OTG mode. + */ +void musb_platform_set_mode(struct musb *musb, u8 musb_mode) +{ + void __iomem *tbase = musb->ctrl_base; + u32 otg_stat, phy_otg_ctrl, phy_otg_ena, dev_conf; + + if (musb->board_mode != MUSB_OTG) { + ERR("Changing mode currently only supported in OTG mode\n"); + return; + } + + otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT); + phy_otg_ctrl = musb_readl(tbase, TUSB_PHY_OTG_CTRL); + phy_otg_ena = musb_readl(tbase, TUSB_PHY_OTG_CTRL_ENABLE); + dev_conf = musb_readl(tbase, TUSB_DEV_CONF); + + switch (musb_mode) { + +#ifdef CONFIG_USB_MUSB_HDRC_HCD + case MUSB_HOST: /* Disable PHY ID detect, ground ID */ + phy_otg_ctrl &= ~TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP; + phy_otg_ena |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP; + dev_conf |= TUSB_DEV_CONF_ID_SEL; + dev_conf &= ~TUSB_DEV_CONF_SOFT_ID; + break; +#endif + +#ifdef CONFIG_USB_GADGET_MUSB_HDRC + case MUSB_PERIPHERAL: /* Disable PHY ID detect, keep ID pull-up on */ + phy_otg_ctrl |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP; + phy_otg_ena |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP; + dev_conf |= (TUSB_DEV_CONF_ID_SEL | TUSB_DEV_CONF_SOFT_ID); + break; +#endif + +#ifdef CONFIG_USB_MUSB_OTG + case MUSB_OTG: /* Use PHY ID detection */ + phy_otg_ctrl |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP; + phy_otg_ena |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP; + dev_conf &= ~(TUSB_DEV_CONF_ID_SEL | TUSB_DEV_CONF_SOFT_ID); + break; +#endif + + default: + DBG(2, "Trying to set unknown mode %i\n", musb_mode); + } + + musb_writel(tbase, TUSB_PHY_OTG_CTRL, + TUSB_PHY_OTG_CTRL_WRPROTECT | phy_otg_ctrl); + musb_writel(tbase, TUSB_PHY_OTG_CTRL_ENABLE, + TUSB_PHY_OTG_CTRL_WRPROTECT | phy_otg_ena); + musb_writel(tbase, TUSB_DEV_CONF, dev_conf); + + otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT); + if ((musb_mode == MUSB_PERIPHERAL) && + !(otg_stat & TUSB_DEV_OTG_STAT_ID_STATUS)) + INFO("Cannot be peripheral with mini-A cable " + "otg_stat: %08x\n", otg_stat); +} + +static inline unsigned long +tusb_otg_ints(struct musb *musb, u32 int_src, void __iomem *tbase) +{ + u32 otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT); + unsigned long idle_timeout = 0; + + /* ID pin */ + if ((int_src & TUSB_INT_SRC_ID_STATUS_CHNG)) { + int default_a; + + if (is_otg_enabled(musb)) + default_a = !(otg_stat & TUSB_DEV_OTG_STAT_ID_STATUS); + else + default_a = is_host_enabled(musb); + DBG(2, "Default-%c\n", default_a ? 'A' : 'B'); + musb->xceiv.default_a = default_a; + tusb_source_power(musb, default_a); + + /* Don't allow idling immediately */ + if (default_a) + idle_timeout = jiffies + (HZ * 3); + } + + /* VBUS state change */ + if (int_src & TUSB_INT_SRC_VBUS_SENSE_CHNG) { + + /* B-dev state machine: no vbus ~= disconnect */ + if ((is_otg_enabled(musb) && !musb->xceiv.default_a) + || !is_host_enabled(musb)) { +#ifdef CONFIG_USB_MUSB_HDRC_HCD + /* ? musb_root_disconnect(musb); */ + musb->port1_status &= + ~(USB_PORT_STAT_CONNECTION + | USB_PORT_STAT_ENABLE + | USB_PORT_STAT_LOW_SPEED + | USB_PORT_STAT_HIGH_SPEED + | USB_PORT_STAT_TEST + ); +#endif + + if (otg_stat & TUSB_DEV_OTG_STAT_SESS_END) { + DBG(1, "Forcing disconnect (no interrupt)\n"); + if (musb->xceiv.state != OTG_STATE_B_IDLE) { + /* INTR_DISCONNECT can hide... */ + musb->xceiv.state = OTG_STATE_B_IDLE; + musb->int_usb |= MUSB_INTR_DISCONNECT; + } + musb->is_active = 0; + } + DBG(2, "vbus change, %s, otg %03x\n", + otg_state_string(musb), otg_stat); + idle_timeout = jiffies + (1 * HZ); + schedule_work(&musb->irq_work); + + } else /* A-dev state machine */ { + DBG(2, "vbus change, %s, otg %03x\n", + otg_state_string(musb), otg_stat); + + switch (musb->xceiv.state) { + case OTG_STATE_A_IDLE: + DBG(2, "Got SRP, turning on VBUS\n"); + musb_set_vbus(musb, 1); + + /* CONNECT can wake if a_wait_bcon is set */ + if (musb->a_wait_bcon != 0) + musb->is_active = 0; + else + musb->is_active = 1; + + /* + * OPT FS A TD.4.6 needs few seconds for + * A_WAIT_VRISE + */ + idle_timeout = jiffies + (2 * HZ); + + break; + case OTG_STATE_A_WAIT_VRISE: + /* ignore; A-session-valid < VBUS_VALID/2, + * we monitor this with the timer + */ + break; + case OTG_STATE_A_WAIT_VFALL: + /* REVISIT this irq triggers during short + * spikes caused by enumeration ... + */ + if (musb->vbuserr_retry) { + musb->vbuserr_retry--; + tusb_source_power(musb, 1); + } else { + musb->vbuserr_retry + = VBUSERR_RETRY_COUNT; + tusb_source_power(musb, 0); + } + break; + default: + break; + } + } + } + + /* OTG timer expiration */ + if (int_src & TUSB_INT_SRC_OTG_TIMEOUT) { + u8 devctl; + + DBG(4, "%s timer, %03x\n", otg_state_string(musb), otg_stat); + + switch (musb->xceiv.state) { + case OTG_STATE_A_WAIT_VRISE: + /* VBUS has probably been valid for a while now, + * but may well have bounced out of range a bit + */ + devctl = musb_readb(musb->mregs, MUSB_DEVCTL); + if (otg_stat & TUSB_DEV_OTG_STAT_VBUS_VALID) { + if ((devctl & MUSB_DEVCTL_VBUS) + != MUSB_DEVCTL_VBUS) { + DBG(2, "devctl %02x\n", devctl); + break; + } + musb->xceiv.state = OTG_STATE_A_WAIT_BCON; + musb->is_active = 0; + idle_timeout = jiffies + + msecs_to_jiffies(musb->a_wait_bcon); + } else { + /* REVISIT report overcurrent to hub? */ + ERR("vbus too slow, devctl %02x\n", devctl); + tusb_source_power(musb, 0); + } + break; + case OTG_STATE_A_WAIT_BCON: + if (musb->a_wait_bcon != 0) + idle_timeout = jiffies + + msecs_to_jiffies(musb->a_wait_bcon); + break; + case OTG_STATE_A_SUSPEND: + break; + case OTG_STATE_B_WAIT_ACON: + break; + default: + break; + } + } + schedule_work(&musb->irq_work); + + return idle_timeout; +} + +static irqreturn_t tusb_interrupt(int irq, void *__hci) +{ + struct musb *musb = __hci; + void __iomem *tbase = musb->ctrl_base; + unsigned long flags, idle_timeout = 0; + u32 int_mask, int_src; + + spin_lock_irqsave(&musb->lock, flags); + + /* Mask all interrupts to allow using both edge and level GPIO irq */ + int_mask = musb_readl(tbase, TUSB_INT_MASK); + musb_writel(tbase, TUSB_INT_MASK, ~TUSB_INT_MASK_RESERVED_BITS); + + int_src = musb_readl(tbase, TUSB_INT_SRC) & ~TUSB_INT_SRC_RESERVED_BITS; + DBG(3, "TUSB IRQ %08x\n", int_src); + + musb->int_usb = (u8) int_src; + + /* Acknowledge wake-up source interrupts */ + if (int_src & TUSB_INT_SRC_DEV_WAKEUP) { + u32 reg; + u32 i; + + if (tusb_get_revision(musb) == TUSB_REV_30) + tusb_wbus_quirk(musb, 0); + + /* there are issues re-locking the PLL on wakeup ... */ + + /* work around issue 8 */ + for (i = 0xf7f7f7; i > 0xf7f7f7 - 1000; i--) { + musb_writel(tbase, TUSB_SCRATCH_PAD, 0); + musb_writel(tbase, TUSB_SCRATCH_PAD, i); + reg = musb_readl(tbase, TUSB_SCRATCH_PAD); + if (reg == i) + break; + DBG(6, "TUSB NOR not ready\n"); + } + + /* work around issue 13 (2nd half) */ + tusb_set_clock_source(musb, 1); + + reg = musb_readl(tbase, TUSB_PRCM_WAKEUP_SOURCE); + musb_writel(tbase, TUSB_PRCM_WAKEUP_CLEAR, reg); + if (reg & ~TUSB_PRCM_WNORCS) { + musb->is_active = 1; + schedule_work(&musb->irq_work); + } + DBG(3, "wake %sactive %02x\n", + musb->is_active ? "" : "in", reg); + + /* REVISIT host side TUSB_PRCM_WHOSTDISCON, TUSB_PRCM_WBUS */ + } + + if (int_src & TUSB_INT_SRC_USB_IP_CONN) + del_timer(&musb_idle_timer); + + /* OTG state change reports (annoyingly) not issued by Mentor core */ + if (int_src & (TUSB_INT_SRC_VBUS_SENSE_CHNG + | TUSB_INT_SRC_OTG_TIMEOUT + | TUSB_INT_SRC_ID_STATUS_CHNG)) + idle_timeout = tusb_otg_ints(musb, int_src, tbase); + + /* TX dma callback must be handled here, RX dma callback is + * handled in tusb_omap_dma_cb. + */ + if ((int_src & TUSB_INT_SRC_TXRX_DMA_DONE)) { + u32 dma_src = musb_readl(tbase, TUSB_DMA_INT_SRC); + u32 real_dma_src = musb_readl(tbase, TUSB_DMA_INT_MASK); + + DBG(3, "DMA IRQ %08x\n", dma_src); + real_dma_src = ~real_dma_src & dma_src; + if (tusb_dma_omap() && real_dma_src) { + int tx_source = (real_dma_src & 0xffff); + int i; + + for (i = 1; i <= 15; i++) { + if (tx_source & (1 << i)) { + DBG(3, "completing ep%i %s\n", i, "tx"); + musb_dma_completion(musb, i, 1); + } + } + } + musb_writel(tbase, TUSB_DMA_INT_CLEAR, dma_src); + } + + /* EP interrupts. In OCP mode tusb6010 mirrors the MUSB interrupts */ + if (int_src & (TUSB_INT_SRC_USB_IP_TX | TUSB_INT_SRC_USB_IP_RX)) { + u32 musb_src = musb_readl(tbase, TUSB_USBIP_INT_SRC); + + musb_writel(tbase, TUSB_USBIP_INT_CLEAR, musb_src); + musb->int_rx = (((musb_src >> 16) & 0xffff) << 1); + musb->int_tx = (musb_src & 0xffff); + } else { + musb->int_rx = 0; + musb->int_tx = 0; + } + + if (int_src & (TUSB_INT_SRC_USB_IP_TX | TUSB_INT_SRC_USB_IP_RX | 0xff)) + musb_interrupt(musb); + + /* Acknowledge TUSB interrupts. Clear only non-reserved bits */ + musb_writel(tbase, TUSB_INT_SRC_CLEAR, + int_src & ~TUSB_INT_MASK_RESERVED_BITS); + + musb_platform_try_idle(musb, idle_timeout); + + musb_writel(tbase, TUSB_INT_MASK, int_mask); + spin_unlock_irqrestore(&musb->lock, flags); + + return IRQ_HANDLED; +} + +static int dma_off; + +/* + * Enables TUSB6010. Caller must take care of locking. + * REVISIT: + * - Check what is unnecessary in MGC_HdrcStart() + */ +void musb_platform_enable(struct musb *musb) +{ + void __iomem *tbase = musb->ctrl_base; + + /* Setup TUSB6010 main interrupt mask. Enable all interrupts except SOF. + * REVISIT: Enable and deal with TUSB_INT_SRC_USB_IP_SOF */ + musb_writel(tbase, TUSB_INT_MASK, TUSB_INT_SRC_USB_IP_SOF); + + /* Setup TUSB interrupt, disable DMA and GPIO interrupts */ + musb_writel(tbase, TUSB_USBIP_INT_MASK, 0); + musb_writel(tbase, TUSB_DMA_INT_MASK, 0x7fffffff); + musb_writel(tbase, TUSB_GPIO_INT_MASK, 0x1ff); + + /* Clear all subsystem interrups */ + musb_writel(tbase, TUSB_USBIP_INT_CLEAR, 0x7fffffff); + musb_writel(tbase, TUSB_DMA_INT_CLEAR, 0x7fffffff); + musb_writel(tbase, TUSB_GPIO_INT_CLEAR, 0x1ff); + + /* Acknowledge pending interrupt(s) */ + musb_writel(tbase, TUSB_INT_SRC_CLEAR, ~TUSB_INT_MASK_RESERVED_BITS); + + /* Only 0 clock cycles for minimum interrupt de-assertion time and + * interrupt polarity active low seems to work reliably here */ + musb_writel(tbase, TUSB_INT_CTRL_CONF, + TUSB_INT_CTRL_CONF_INT_RELCYC(0)); + + set_irq_type(musb->nIrq, IRQ_TYPE_LEVEL_LOW); + + /* maybe force into the Default-A OTG state machine */ + if (!(musb_readl(tbase, TUSB_DEV_OTG_STAT) + & TUSB_DEV_OTG_STAT_ID_STATUS)) + musb_writel(tbase, TUSB_INT_SRC_SET, + TUSB_INT_SRC_ID_STATUS_CHNG); + + if (is_dma_capable() && dma_off) + printk(KERN_WARNING "%s %s: dma not reactivated\n", + __FILE__, __func__); + else + dma_off = 1; +} + +/* + * Disables TUSB6010. Caller must take care of locking. + */ +void musb_platform_disable(struct musb *musb) +{ + void __iomem *tbase = musb->ctrl_base; + + /* FIXME stop DMA, IRQs, timers, ... */ + + /* disable all IRQs */ + musb_writel(tbase, TUSB_INT_MASK, ~TUSB_INT_MASK_RESERVED_BITS); + musb_writel(tbase, TUSB_USBIP_INT_MASK, 0x7fffffff); + musb_writel(tbase, TUSB_DMA_INT_MASK, 0x7fffffff); + musb_writel(tbase, TUSB_GPIO_INT_MASK, 0x1ff); + + del_timer(&musb_idle_timer); + + if (is_dma_capable() && !dma_off) { + printk(KERN_WARNING "%s %s: dma still active\n", + __FILE__, __func__); + dma_off = 1; + } +} + +/* + * Sets up TUSB6010 CPU interface specific signals and registers + * Note: Settings optimized for OMAP24xx + */ +static void __init tusb_setup_cpu_interface(struct musb *musb) +{ + void __iomem *tbase = musb->ctrl_base; + + /* + * Disable GPIO[5:0] pullups (used as output DMA requests) + * Don't disable GPIO[7:6] as they are needed for wake-up. + */ + musb_writel(tbase, TUSB_PULLUP_1_CTRL, 0x0000003F); + + /* Disable all pullups on NOR IF, DMAREQ0 and DMAREQ1 */ + musb_writel(tbase, TUSB_PULLUP_2_CTRL, 0x01FFFFFF); + + /* Turn GPIO[5:0] to DMAREQ[5:0] signals */ + musb_writel(tbase, TUSB_GPIO_CONF, TUSB_GPIO_CONF_DMAREQ(0x3f)); + + /* Burst size 16x16 bits, all six DMA requests enabled, DMA request + * de-assertion time 2 system clocks p 62 */ + musb_writel(tbase, TUSB_DMA_REQ_CONF, + TUSB_DMA_REQ_CONF_BURST_SIZE(2) | + TUSB_DMA_REQ_CONF_DMA_REQ_EN(0x3f) | + TUSB_DMA_REQ_CONF_DMA_REQ_ASSER(2)); + + /* Set 0 wait count for synchronous burst access */ + musb_writel(tbase, TUSB_WAIT_COUNT, 1); +} + +static int __init tusb_start(struct musb *musb) +{ + void __iomem *tbase = musb->ctrl_base; + int ret = 0; + unsigned long flags; + u32 reg; + + if (musb->board_set_power) + ret = musb->board_set_power(1); + if (ret != 0) { + printk(KERN_ERR "tusb: Cannot enable TUSB6010\n"); + return ret; + } + + spin_lock_irqsave(&musb->lock, flags); + + if (musb_readl(tbase, TUSB_PROD_TEST_RESET) != + TUSB_PROD_TEST_RESET_VAL) { + printk(KERN_ERR "tusb: Unable to detect TUSB6010\n"); + goto err; + } + + ret = tusb_print_revision(musb); + if (ret < 2) { + printk(KERN_ERR "tusb: Unsupported TUSB6010 revision %i\n", + ret); + goto err; + } + + /* The uint bit for "USB non-PDR interrupt enable" has to be 1 when + * NOR FLASH interface is used */ + musb_writel(tbase, TUSB_VLYNQ_CTRL, 8); + + /* Select PHY free running 60MHz as a system clock */ + tusb_set_clock_source(musb, 1); + + /* VBus valid timer 1us, disable DFT/Debug and VLYNQ clocks for + * power saving, enable VBus detect and session end comparators, + * enable IDpullup, enable VBus charging */ + musb_writel(tbase, TUSB_PRCM_MNGMT, + TUSB_PRCM_MNGMT_VBUS_VALID_TIMER(0xa) | + TUSB_PRCM_MNGMT_VBUS_VALID_FLT_EN | + TUSB_PRCM_MNGMT_OTG_SESS_END_EN | + TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN | + TUSB_PRCM_MNGMT_OTG_ID_PULLUP); + tusb_setup_cpu_interface(musb); + + /* simplify: always sense/pullup ID pins, as if in OTG mode */ + reg = musb_readl(tbase, TUSB_PHY_OTG_CTRL_ENABLE); + reg |= TUSB_PHY_OTG_CTRL_WRPROTECT | TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP; + musb_writel(tbase, TUSB_PHY_OTG_CTRL_ENABLE, reg); + + reg = musb_readl(tbase, TUSB_PHY_OTG_CTRL); + reg |= TUSB_PHY_OTG_CTRL_WRPROTECT | TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP; + musb_writel(tbase, TUSB_PHY_OTG_CTRL, reg); + + spin_unlock_irqrestore(&musb->lock, flags); + + return 0; + +err: + spin_unlock_irqrestore(&musb->lock, flags); + + if (musb->board_set_power) + musb->board_set_power(0); + + return -ENODEV; +} + +int __init musb_platform_init(struct musb *musb) +{ + struct platform_device *pdev; + struct resource *mem; + void __iomem *sync; + int ret; + + pdev = to_platform_device(musb->controller); + + /* dma address for async dma */ + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + musb->async = mem->start; + + /* dma address for sync dma */ + mem = platform_get_resource(pdev, IORESOURCE_MEM, 1); + if (!mem) { + pr_debug("no sync dma resource?\n"); + return -ENODEV; + } + musb->sync = mem->start; + + sync = ioremap(mem->start, mem->end - mem->start + 1); + if (!sync) { + pr_debug("ioremap for sync failed\n"); + return -ENOMEM; + } + musb->sync_va = sync; + + /* Offsets from base: VLYNQ at 0x000, MUSB regs at 0x400, + * FIFOs at 0x600, TUSB at 0x800 + */ + musb->mregs += TUSB_BASE_OFFSET; + + ret = tusb_start(musb); + if (ret) { + printk(KERN_ERR "Could not start tusb6010 (%d)\n", + ret); + return -ENODEV; + } + musb->isr = tusb_interrupt; + + if (is_host_enabled(musb)) + musb->board_set_vbus = tusb_source_power; + if (is_peripheral_enabled(musb)) + musb->xceiv.set_power = tusb_draw_power; + + setup_timer(&musb_idle_timer, musb_do_idle, (unsigned long) musb); + + return ret; +} + +int musb_platform_exit(struct musb *musb) +{ + del_timer_sync(&musb_idle_timer); + + if (musb->board_set_power) + musb->board_set_power(0); + + iounmap(musb->sync_va); + + return 0; +} diff --git a/drivers/usb/musb/tusb6010.h b/drivers/usb/musb/tusb6010.h new file mode 100644 index 00000000000..db6dad0750a --- /dev/null +++ b/drivers/usb/musb/tusb6010.h @@ -0,0 +1,402 @@ +/* + * Definitions for TUSB6010 USB 2.0 OTG Dual Role controller + * + * Copyright (C) 2006 Nokia Corporation + * Jarkko Nikula + * Tony Lindgren + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __TUSB6010_H__ +#define __TUSB6010_H__ + +extern u8 tusb_get_revision(struct musb *musb); + +#ifdef CONFIG_USB_TUSB6010 +#define musb_in_tusb() 1 +#else +#define musb_in_tusb() 0 +#endif + +#ifdef CONFIG_USB_TUSB_OMAP_DMA +#define tusb_dma_omap() 1 +#else +#define tusb_dma_omap() 0 +#endif + +/* VLYNQ control register. 32-bit at offset 0x000 */ +#define TUSB_VLYNQ_CTRL 0x004 + +/* Mentor Graphics OTG core registers. 8,- 16- and 32-bit at offset 0x400 */ +#define TUSB_BASE_OFFSET 0x400 + +/* FIFO registers 32-bit at offset 0x600 */ +#define TUSB_FIFO_BASE 0x600 + +/* Device System & Control registers. 32-bit at offset 0x800 */ +#define TUSB_SYS_REG_BASE 0x800 + +#define TUSB_DEV_CONF (TUSB_SYS_REG_BASE + 0x000) +#define TUSB_DEV_CONF_USB_HOST_MODE (1 << 16) +#define TUSB_DEV_CONF_PROD_TEST_MODE (1 << 15) +#define TUSB_DEV_CONF_SOFT_ID (1 << 1) +#define TUSB_DEV_CONF_ID_SEL (1 << 0) + +#define TUSB_PHY_OTG_CTRL_ENABLE (TUSB_SYS_REG_BASE + 0x004) +#define TUSB_PHY_OTG_CTRL (TUSB_SYS_REG_BASE + 0x008) +#define TUSB_PHY_OTG_CTRL_WRPROTECT (0xa5 << 24) +#define TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP (1 << 23) +#define TUSB_PHY_OTG_CTRL_OTG_VBUS_DET_EN (1 << 19) +#define TUSB_PHY_OTG_CTRL_OTG_SESS_END_EN (1 << 18) +#define TUSB_PHY_OTG_CTRL_TESTM2 (1 << 17) +#define TUSB_PHY_OTG_CTRL_TESTM1 (1 << 16) +#define TUSB_PHY_OTG_CTRL_TESTM0 (1 << 15) +#define TUSB_PHY_OTG_CTRL_TX_DATA2 (1 << 14) +#define TUSB_PHY_OTG_CTRL_TX_GZ2 (1 << 13) +#define TUSB_PHY_OTG_CTRL_TX_ENABLE2 (1 << 12) +#define TUSB_PHY_OTG_CTRL_DM_PULLDOWN (1 << 11) +#define TUSB_PHY_OTG_CTRL_DP_PULLDOWN (1 << 10) +#define TUSB_PHY_OTG_CTRL_OSC_EN (1 << 9) +#define TUSB_PHY_OTG_CTRL_PHYREF_CLKSEL(v) (((v) & 3) << 7) +#define TUSB_PHY_OTG_CTRL_PD (1 << 6) +#define TUSB_PHY_OTG_CTRL_PLL_ON (1 << 5) +#define TUSB_PHY_OTG_CTRL_EXT_RPU (1 << 4) +#define TUSB_PHY_OTG_CTRL_PWR_GOOD (1 << 3) +#define TUSB_PHY_OTG_CTRL_RESET (1 << 2) +#define TUSB_PHY_OTG_CTRL_SUSPENDM (1 << 1) +#define TUSB_PHY_OTG_CTRL_CLK_MODE (1 << 0) + +/*OTG status register */ +#define TUSB_DEV_OTG_STAT (TUSB_SYS_REG_BASE + 0x00c) +#define TUSB_DEV_OTG_STAT_PWR_CLK_GOOD (1 << 8) +#define TUSB_DEV_OTG_STAT_SESS_END (1 << 7) +#define TUSB_DEV_OTG_STAT_SESS_VALID (1 << 6) +#define TUSB_DEV_OTG_STAT_VBUS_VALID (1 << 5) +#define TUSB_DEV_OTG_STAT_VBUS_SENSE (1 << 4) +#define TUSB_DEV_OTG_STAT_ID_STATUS (1 << 3) +#define TUSB_DEV_OTG_STAT_HOST_DISCON (1 << 2) +#define TUSB_DEV_OTG_STAT_LINE_STATE (3 << 0) +#define TUSB_DEV_OTG_STAT_DP_ENABLE (1 << 1) +#define TUSB_DEV_OTG_STAT_DM_ENABLE (1 << 0) + +#define TUSB_DEV_OTG_TIMER (TUSB_SYS_REG_BASE + 0x010) +# define TUSB_DEV_OTG_TIMER_ENABLE (1 << 31) +# define TUSB_DEV_OTG_TIMER_VAL(v) ((v) & 0x07ffffff) +#define TUSB_PRCM_REV (TUSB_SYS_REG_BASE + 0x014) + +/* PRCM configuration register */ +#define TUSB_PRCM_CONF (TUSB_SYS_REG_BASE + 0x018) +#define TUSB_PRCM_CONF_SFW_CPEN (1 << 24) +#define TUSB_PRCM_CONF_SYS_CLKSEL(v) (((v) & 3) << 16) + +/* PRCM management register */ +#define TUSB_PRCM_MNGMT (TUSB_SYS_REG_BASE + 0x01c) +#define TUSB_PRCM_MNGMT_SRP_FIX_TIMER(v) (((v) & 0xf) << 25) +#define TUSB_PRCM_MNGMT_SRP_FIX_EN (1 << 24) +#define TUSB_PRCM_MNGMT_VBUS_VALID_TIMER(v) (((v) & 0xf) << 20) +#define TUSB_PRCM_MNGMT_VBUS_VALID_FLT_EN (1 << 19) +#define TUSB_PRCM_MNGMT_DFT_CLK_DIS (1 << 18) +#define TUSB_PRCM_MNGMT_VLYNQ_CLK_DIS (1 << 17) +#define TUSB_PRCM_MNGMT_OTG_SESS_END_EN (1 << 10) +#define TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN (1 << 9) +#define TUSB_PRCM_MNGMT_OTG_ID_PULLUP (1 << 8) +#define TUSB_PRCM_MNGMT_15_SW_EN (1 << 4) +#define TUSB_PRCM_MNGMT_33_SW_EN (1 << 3) +#define TUSB_PRCM_MNGMT_5V_CPEN (1 << 2) +#define TUSB_PRCM_MNGMT_PM_IDLE (1 << 1) +#define TUSB_PRCM_MNGMT_DEV_IDLE (1 << 0) + +/* Wake-up source clear and mask registers */ +#define TUSB_PRCM_WAKEUP_SOURCE (TUSB_SYS_REG_BASE + 0x020) +#define TUSB_PRCM_WAKEUP_CLEAR (TUSB_SYS_REG_BASE + 0x028) +#define TUSB_PRCM_WAKEUP_MASK (TUSB_SYS_REG_BASE + 0x02c) +#define TUSB_PRCM_WAKEUP_RESERVED_BITS (0xffffe << 13) +#define TUSB_PRCM_WGPIO_7 (1 << 12) +#define TUSB_PRCM_WGPIO_6 (1 << 11) +#define TUSB_PRCM_WGPIO_5 (1 << 10) +#define TUSB_PRCM_WGPIO_4 (1 << 9) +#define TUSB_PRCM_WGPIO_3 (1 << 8) +#define TUSB_PRCM_WGPIO_2 (1 << 7) +#define TUSB_PRCM_WGPIO_1 (1 << 6) +#define TUSB_PRCM_WGPIO_0 (1 << 5) +#define TUSB_PRCM_WHOSTDISCON (1 << 4) /* Host disconnect */ +#define TUSB_PRCM_WBUS (1 << 3) /* USB bus resume */ +#define TUSB_PRCM_WNORCS (1 << 2) /* NOR chip select */ +#define TUSB_PRCM_WVBUS (1 << 1) /* OTG PHY VBUS */ +#define TUSB_PRCM_WID (1 << 0) /* OTG PHY ID detect */ + +#define TUSB_PULLUP_1_CTRL (TUSB_SYS_REG_BASE + 0x030) +#define TUSB_PULLUP_2_CTRL (TUSB_SYS_REG_BASE + 0x034) +#define TUSB_INT_CTRL_REV (TUSB_SYS_REG_BASE + 0x038) +#define TUSB_INT_CTRL_CONF (TUSB_SYS_REG_BASE + 0x03c) +#define TUSB_USBIP_INT_SRC (TUSB_SYS_REG_BASE + 0x040) +#define TUSB_USBIP_INT_SET (TUSB_SYS_REG_BASE + 0x044) +#define TUSB_USBIP_INT_CLEAR (TUSB_SYS_REG_BASE + 0x048) +#define TUSB_USBIP_INT_MASK (TUSB_SYS_REG_BASE + 0x04c) +#define TUSB_DMA_INT_SRC (TUSB_SYS_REG_BASE + 0x050) +#define TUSB_DMA_INT_SET (TUSB_SYS_REG_BASE + 0x054) +#define TUSB_DMA_INT_CLEAR (TUSB_SYS_REG_BASE + 0x058) +#define TUSB_DMA_INT_MASK (TUSB_SYS_REG_BASE + 0x05c) +#define TUSB_GPIO_INT_SRC (TUSB_SYS_REG_BASE + 0x060) +#define TUSB_GPIO_INT_SET (TUSB_SYS_REG_BASE + 0x064) +#define TUSB_GPIO_INT_CLEAR (TUSB_SYS_REG_BASE + 0x068) +#define TUSB_GPIO_INT_MASK (TUSB_SYS_REG_BASE + 0x06c) + +/* NOR flash interrupt source registers */ +#define TUSB_INT_SRC (TUSB_SYS_REG_BASE + 0x070) +#define TUSB_INT_SRC_SET (TUSB_SYS_REG_BASE + 0x074) +#define TUSB_INT_SRC_CLEAR (TUSB_SYS_REG_BASE + 0x078) +#define TUSB_INT_MASK (TUSB_SYS_REG_BASE + 0x07c) +#define TUSB_INT_SRC_TXRX_DMA_DONE (1 << 24) +#define TUSB_INT_SRC_USB_IP_CORE (1 << 17) +#define TUSB_INT_SRC_OTG_TIMEOUT (1 << 16) +#define TUSB_INT_SRC_VBUS_SENSE_CHNG (1 << 15) +#define TUSB_INT_SRC_ID_STATUS_CHNG (1 << 14) +#define TUSB_INT_SRC_DEV_WAKEUP (1 << 13) +#define TUSB_INT_SRC_DEV_READY (1 << 12) +#define TUSB_INT_SRC_USB_IP_TX (1 << 9) +#define TUSB_INT_SRC_USB_IP_RX (1 << 8) +#define TUSB_INT_SRC_USB_IP_VBUS_ERR (1 << 7) +#define TUSB_INT_SRC_USB_IP_VBUS_REQ (1 << 6) +#define TUSB_INT_SRC_USB_IP_DISCON (1 << 5) +#define TUSB_INT_SRC_USB_IP_CONN (1 << 4) +#define TUSB_INT_SRC_USB_IP_SOF (1 << 3) +#define TUSB_INT_SRC_USB_IP_RST_BABBLE (1 << 2) +#define TUSB_INT_SRC_USB_IP_RESUME (1 << 1) +#define TUSB_INT_SRC_USB_IP_SUSPEND (1 << 0) + +/* NOR flash interrupt registers reserved bits. Must be written as 0 */ +#define TUSB_INT_MASK_RESERVED_17 (0x3fff << 17) +#define TUSB_INT_MASK_RESERVED_13 (1 << 13) +#define TUSB_INT_MASK_RESERVED_8 (0xf << 8) +#define TUSB_INT_SRC_RESERVED_26 (0x1f << 26) +#define TUSB_INT_SRC_RESERVED_18 (0x3f << 18) +#define TUSB_INT_SRC_RESERVED_10 (0x03 << 10) + +/* Reserved bits for NOR flash interrupt mask and clear register */ +#define TUSB_INT_MASK_RESERVED_BITS (TUSB_INT_MASK_RESERVED_17 | \ + TUSB_INT_MASK_RESERVED_13 | \ + TUSB_INT_MASK_RESERVED_8) + +/* Reserved bits for NOR flash interrupt status register */ +#define TUSB_INT_SRC_RESERVED_BITS (TUSB_INT_SRC_RESERVED_26 | \ + TUSB_INT_SRC_RESERVED_18 | \ + TUSB_INT_SRC_RESERVED_10) + +#define TUSB_GPIO_REV (TUSB_SYS_REG_BASE + 0x080) +#define TUSB_GPIO_CONF (TUSB_SYS_REG_BASE + 0x084) +#define TUSB_DMA_CTRL_REV (TUSB_SYS_REG_BASE + 0x100) +#define TUSB_DMA_REQ_CONF (TUSB_SYS_REG_BASE + 0x104) +#define TUSB_EP0_CONF (TUSB_SYS_REG_BASE + 0x108) +#define TUSB_DMA_EP_MAP (TUSB_SYS_REG_BASE + 0x148) + +/* Offsets from each ep base register */ +#define TUSB_EP_TX_OFFSET 0x10c /* EP_IN in docs */ +#define TUSB_EP_RX_OFFSET 0x14c /* EP_OUT in docs */ +#define TUSB_EP_MAX_PACKET_SIZE_OFFSET 0x188 + +#define TUSB_WAIT_COUNT (TUSB_SYS_REG_BASE + 0x1c8) +#define TUSB_SCRATCH_PAD (TUSB_SYS_REG_BASE + 0x1c4) +#define TUSB_PROD_TEST_RESET (TUSB_SYS_REG_BASE + 0x1d8) + +/* Device System & Control register bitfields */ +#define TUSB_INT_CTRL_CONF_INT_RELCYC(v) (((v) & 0x7) << 18) +#define TUSB_INT_CTRL_CONF_INT_POLARITY (1 << 17) +#define TUSB_INT_CTRL_CONF_INT_MODE (1 << 16) +#define TUSB_GPIO_CONF_DMAREQ(v) (((v) & 0x3f) << 24) +#define TUSB_DMA_REQ_CONF_BURST_SIZE(v) (((v) & 3) << 26) +#define TUSB_DMA_REQ_CONF_DMA_REQ_EN(v) (((v) & 0x3f) << 20) +#define TUSB_DMA_REQ_CONF_DMA_REQ_ASSER(v) (((v) & 0xf) << 16) +#define TUSB_EP0_CONFIG_SW_EN (1 << 8) +#define TUSB_EP0_CONFIG_DIR_TX (1 << 7) +#define TUSB_EP0_CONFIG_XFR_SIZE(v) ((v) & 0x7f) +#define TUSB_EP_CONFIG_SW_EN (1 << 31) +#define TUSB_EP_CONFIG_XFR_SIZE(v) ((v) & 0x7fffffff) +#define TUSB_PROD_TEST_RESET_VAL 0xa596 +#define TUSB_EP_FIFO(ep) (TUSB_FIFO_BASE + (ep) * 0x20) + +#define TUSB_DIDR1_LO (TUSB_SYS_REG_BASE + 0x1f8) +#define TUSB_DIDR1_HI (TUSB_SYS_REG_BASE + 0x1fc) +#define TUSB_DIDR1_HI_CHIP_REV(v) (((v) >> 17) & 0xf) +#define TUSB_DIDR1_HI_REV_20 0 +#define TUSB_DIDR1_HI_REV_30 1 +#define TUSB_DIDR1_HI_REV_31 2 + +#define TUSB_REV_10 0x10 +#define TUSB_REV_20 0x20 +#define TUSB_REV_30 0x30 +#define TUSB_REV_31 0x31 + +/*----------------------------------------------------------------------------*/ + +#ifdef CONFIG_USB_TUSB6010 + +/* configuration parameters specific to this silicon */ + +/* Number of Tx endpoints. Legal values are 1 - 16 (this value includes EP0) */ +#define MUSB_C_NUM_EPT 16 + +/* Number of Rx endpoints. Legal values are 1 - 16 (this value includes EP0) */ +#define MUSB_C_NUM_EPR 16 + +/* Endpoint 1 to 15 direction types. C_EP1_DEF is defined if either Tx endpoint + * 1 or Rx endpoint 1 are used. + */ +#define MUSB_C_EP1_DEF + +/* C_EP1_TX_DEF is defined if Tx endpoint 1 is used */ +#define MUSB_C_EP1_TX_DEF + +/* C_EP1_RX_DEF is defined if Rx endpoint 1 is used */ +#define MUSB_C_EP1_RX_DEF + +/* C_EP1_TOR_DEF is defined if Tx endpoint 1 and Rx endpoint 1 share a FIFO */ +/* #define C_EP1_TOR_DEF */ + +/* C_EP1_TAR_DEF is defined if both Tx endpoint 1 and Rx endpoint 1 are used + * and do not share a FIFO. + */ +#define MUSB_C_EP1_TAR_DEF + +/* Similarly for all other used endpoints */ +#define MUSB_C_EP2_DEF +#define MUSB_C_EP2_TX_DEF +#define MUSB_C_EP2_RX_DEF +#define MUSB_C_EP2_TAR_DEF +#define MUSB_C_EP3_DEF +#define MUSB_C_EP3_TX_DEF +#define MUSB_C_EP3_RX_DEF +#define MUSB_C_EP3_TAR_DEF +#define MUSB_C_EP4_DEF +#define MUSB_C_EP4_TX_DEF +#define MUSB_C_EP4_RX_DEF +#define MUSB_C_EP4_TAR_DEF + +/* Endpoint 1 to 15 FIFO address bits. Legal values are 3 to 13 - corresponding + * to FIFO sizes of 8 to 8192 bytes. If an Tx endpoint shares a FIFO with an Rx + * endpoint then the Rx FIFO size must be the same as the Tx FIFO size. All + * endpoints 1 to 15 must be defined, unused endpoints should be set to 2. + */ +#define MUSB_C_EP1T_BITS 5 +#define MUSB_C_EP1R_BITS 5 +#define MUSB_C_EP2T_BITS 5 +#define MUSB_C_EP2R_BITS 5 +#define MUSB_C_EP3T_BITS 3 +#define MUSB_C_EP3R_BITS 3 +#define MUSB_C_EP4T_BITS 3 +#define MUSB_C_EP4R_BITS 3 + +#define MUSB_C_EP5T_BITS 2 +#define MUSB_C_EP5R_BITS 2 +#define MUSB_C_EP6T_BITS 2 +#define MUSB_C_EP6R_BITS 2 +#define MUSB_C_EP7T_BITS 2 +#define MUSB_C_EP7R_BITS 2 +#define MUSB_C_EP8T_BITS 2 +#define MUSB_C_EP8R_BITS 2 +#define MUSB_C_EP9T_BITS 2 +#define MUSB_C_EP9R_BITS 2 +#define MUSB_C_EP10T_BITS 2 +#define MUSB_C_EP10R_BITS 2 +#define MUSB_C_EP11T_BITS 2 +#define MUSB_C_EP11R_BITS 2 +#define MUSB_C_EP12T_BITS 2 +#define MUSB_C_EP12R_BITS 2 +#define MUSB_C_EP13T_BITS 2 +#define MUSB_C_EP13R_BITS 2 +#define MUSB_C_EP14T_BITS 2 +#define MUSB_C_EP14R_BITS 2 +#define MUSB_C_EP15T_BITS 2 +#define MUSB_C_EP15R_BITS 2 + +/* Define the following constant if the USB2.0 Transceiver Macrocell data width + * is 16-bits. + */ +/* #define C_UTM_16 */ + +/* Define this constant if the CPU uses big-endian byte ordering. */ +/* #define C_BIGEND */ + +/* Define the following constant if any Tx endpoint is required to support + * multiple bulk packets. + */ +/* #define C_MP_TX */ + +/* Define the following constant if any Rx endpoint is required to support + * multiple bulk packets. + */ +/* #define C_MP_RX */ + +/* Define the following constant if any Tx endpoint is required to support high + * bandwidth ISO. + */ +/* #define C_HB_TX */ + +/* Define the following constant if any Rx endpoint is required to support high + * bandwidth ISO. + */ +/* #define C_HB_RX */ + +/* Define the following constant if software connect/disconnect control is + * required. + */ +#define MUSB_C_SOFT_CON + +/* Define the following constant if Vendor Control Registers are required. */ +/* #define C_VEND_REG */ + +/* Vendor control register widths. */ +#define MUSB_C_VCTL_BITS 4 +#define MUSB_C_VSTAT_BITS 8 + +/* Define the following constant to include a DMA controller. */ +/* #define C_DMA */ + +/* Define the following constant if 2 or more DMA channels are required. */ +/* #define C_DMA2 */ + +/* Define the following constant if 3 or more DMA channels are required. */ +/* #define C_DMA3 */ + +/* Define the following constant if 4 or more DMA channels are required. */ +/* #define C_DMA4 */ + +/* Define the following constant if 5 or more DMA channels are required. */ +/* #define C_DMA5 */ + +/* Define the following constant if 6 or more DMA channels are required. */ +/* #define C_DMA6 */ + +/* Define the following constant if 7 or more DMA channels are required. */ +/* #define C_DMA7 */ + +/* Define the following constant if 8 or more DMA channels are required. */ +/* #define C_DMA8 */ + +/* Enable Dynamic FIFO Sizing */ +#define MUSB_C_DYNFIFO_DEF + +/* Derived constants. The following constants are derived from the previous + * configuration constants + */ + +/* Total number of endpoints. Legal values are 2 - 16. This must be equal to + * the larger of C_NUM_EPT, C_NUM_EPR + */ +/* #define MUSB_C_NUM_EPS 5 */ + +/* C_EPMAX_BITS is equal to the largest endpoint FIFO word address bits */ +#define MUSB_C_EPMAX_BITS 11 + +/* C_RAM_BITS is the number of address bits required to address the RAM (32-bit + * addresses). It is defined as log2 of the sum of 2** of all the endpoint FIFO + * dword address bits (rounded up). + */ +#define MUSB_C_RAM_BITS 12 + +#endif /* CONFIG_USB_TUSB6010 */ + +#endif /* __TUSB6010_H__ */ diff --git a/drivers/usb/musb/tusb6010_omap.c b/drivers/usb/musb/tusb6010_omap.c new file mode 100644 index 00000000000..52f7f29cebd --- /dev/null +++ b/drivers/usb/musb/tusb6010_omap.c @@ -0,0 +1,719 @@ +/* + * TUSB6010 USB 2.0 OTG Dual Role controller OMAP DMA interface + * + * Copyright (C) 2006 Nokia Corporation + * Tony Lindgren + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "musb_core.h" + +#define to_chdat(c) ((struct tusb_omap_dma_ch *)(c)->private_data) + +#define MAX_DMAREQ 5 /* REVISIT: Really 6, but req5 not OK */ + +struct tusb_omap_dma_ch { + struct musb *musb; + void __iomem *tbase; + unsigned long phys_offset; + int epnum; + u8 tx; + struct musb_hw_ep *hw_ep; + + int ch; + s8 dmareq; + s8 sync_dev; + + struct tusb_omap_dma *tusb_dma; + + void __iomem *dma_addr; + + u32 len; + u16 packet_sz; + u16 transfer_packet_sz; + u32 transfer_len; + u32 completed_len; +}; + +struct tusb_omap_dma { + struct dma_controller controller; + struct musb *musb; + void __iomem *tbase; + + int ch; + s8 dmareq; + s8 sync_dev; + unsigned multichannel:1; +}; + +static int tusb_omap_dma_start(struct dma_controller *c) +{ + struct tusb_omap_dma *tusb_dma; + + tusb_dma = container_of(c, struct tusb_omap_dma, controller); + + /* DBG(3, "ep%i ch: %i\n", chdat->epnum, chdat->ch); */ + + return 0; +} + +static int tusb_omap_dma_stop(struct dma_controller *c) +{ + struct tusb_omap_dma *tusb_dma; + + tusb_dma = container_of(c, struct tusb_omap_dma, controller); + + /* DBG(3, "ep%i ch: %i\n", chdat->epnum, chdat->ch); */ + + return 0; +} + +/* + * Allocate dmareq0 to the current channel unless it's already taken + */ +static inline int tusb_omap_use_shared_dmareq(struct tusb_omap_dma_ch *chdat) +{ + u32 reg = musb_readl(chdat->tbase, TUSB_DMA_EP_MAP); + + if (reg != 0) { + DBG(3, "ep%i dmareq0 is busy for ep%i\n", + chdat->epnum, reg & 0xf); + return -EAGAIN; + } + + if (chdat->tx) + reg = (1 << 4) | chdat->epnum; + else + reg = chdat->epnum; + + musb_writel(chdat->tbase, TUSB_DMA_EP_MAP, reg); + + return 0; +} + +static inline void tusb_omap_free_shared_dmareq(struct tusb_omap_dma_ch *chdat) +{ + u32 reg = musb_readl(chdat->tbase, TUSB_DMA_EP_MAP); + + if ((reg & 0xf) != chdat->epnum) { + printk(KERN_ERR "ep%i trying to release dmareq0 for ep%i\n", + chdat->epnum, reg & 0xf); + return; + } + musb_writel(chdat->tbase, TUSB_DMA_EP_MAP, 0); +} + +/* + * See also musb_dma_completion in plat_uds.c and musb_g_[tx|rx]() in + * musb_gadget.c. + */ +static void tusb_omap_dma_cb(int lch, u16 ch_status, void *data) +{ + struct dma_channel *channel = (struct dma_channel *)data; + struct tusb_omap_dma_ch *chdat = to_chdat(channel); + struct tusb_omap_dma *tusb_dma = chdat->tusb_dma; + struct musb *musb = chdat->musb; + struct musb_hw_ep *hw_ep = chdat->hw_ep; + void __iomem *ep_conf = hw_ep->conf; + void __iomem *mbase = musb->mregs; + unsigned long remaining, flags, pio; + int ch; + + spin_lock_irqsave(&musb->lock, flags); + + if (tusb_dma->multichannel) + ch = chdat->ch; + else + ch = tusb_dma->ch; + + if (ch_status != OMAP_DMA_BLOCK_IRQ) + printk(KERN_ERR "TUSB DMA error status: %i\n", ch_status); + + DBG(3, "ep%i %s dma callback ch: %i status: %x\n", + chdat->epnum, chdat->tx ? "tx" : "rx", + ch, ch_status); + + if (chdat->tx) + remaining = musb_readl(ep_conf, TUSB_EP_TX_OFFSET); + else + remaining = musb_readl(ep_conf, TUSB_EP_RX_OFFSET); + + remaining = TUSB_EP_CONFIG_XFR_SIZE(remaining); + + /* HW issue #10: XFR_SIZE may get corrupt on DMA (both async & sync) */ + if (unlikely(remaining > chdat->transfer_len)) { + DBG(2, "Corrupt %s dma ch%i XFR_SIZE: 0x%08lx\n", + chdat->tx ? "tx" : "rx", chdat->ch, + remaining); + remaining = 0; + } + + channel->actual_len = chdat->transfer_len - remaining; + pio = chdat->len - channel->actual_len; + + DBG(3, "DMA remaining %lu/%u\n", remaining, chdat->transfer_len); + + /* Transfer remaining 1 - 31 bytes */ + if (pio > 0 && pio < 32) { + u8 *buf; + + DBG(3, "Using PIO for remaining %lu bytes\n", pio); + buf = phys_to_virt((u32)chdat->dma_addr) + chdat->transfer_len; + if (chdat->tx) { + dma_cache_maint(phys_to_virt((u32)chdat->dma_addr), + chdat->transfer_len, DMA_TO_DEVICE); + musb_write_fifo(hw_ep, pio, buf); + } else { + musb_read_fifo(hw_ep, pio, buf); + dma_cache_maint(phys_to_virt((u32)chdat->dma_addr), + chdat->transfer_len, DMA_FROM_DEVICE); + } + channel->actual_len += pio; + } + + if (!tusb_dma->multichannel) + tusb_omap_free_shared_dmareq(chdat); + + channel->status = MUSB_DMA_STATUS_FREE; + + /* Handle only RX callbacks here. TX callbacks must be handled based + * on the TUSB DMA status interrupt. + * REVISIT: Use both TUSB DMA status interrupt and OMAP DMA callback + * interrupt for RX and TX. + */ + if (!chdat->tx) + musb_dma_completion(musb, chdat->epnum, chdat->tx); + + /* We must terminate short tx transfers manually by setting TXPKTRDY. + * REVISIT: This same problem may occur with other MUSB dma as well. + * Easy to test with g_ether by pinging the MUSB board with ping -s54. + */ + if ((chdat->transfer_len < chdat->packet_sz) + || (chdat->transfer_len % chdat->packet_sz != 0)) { + u16 csr; + + if (chdat->tx) { + DBG(3, "terminating short tx packet\n"); + musb_ep_select(mbase, chdat->epnum); + csr = musb_readw(hw_ep->regs, MUSB_TXCSR); + csr |= MUSB_TXCSR_MODE | MUSB_TXCSR_TXPKTRDY + | MUSB_TXCSR_P_WZC_BITS; + musb_writew(hw_ep->regs, MUSB_TXCSR, csr); + } + } + + spin_unlock_irqrestore(&musb->lock, flags); +} + +static int tusb_omap_dma_program(struct dma_channel *channel, u16 packet_sz, + u8 rndis_mode, dma_addr_t dma_addr, u32 len) +{ + struct tusb_omap_dma_ch *chdat = to_chdat(channel); + struct tusb_omap_dma *tusb_dma = chdat->tusb_dma; + struct musb *musb = chdat->musb; + struct musb_hw_ep *hw_ep = chdat->hw_ep; + void __iomem *mbase = musb->mregs; + void __iomem *ep_conf = hw_ep->conf; + dma_addr_t fifo = hw_ep->fifo_sync; + struct omap_dma_channel_params dma_params; + u32 dma_remaining; + int src_burst, dst_burst; + u16 csr; + int ch; + s8 dmareq; + s8 sync_dev; + + if (unlikely(dma_addr & 0x1) || (len < 32) || (len > packet_sz)) + return false; + + /* + * HW issue #10: Async dma will eventually corrupt the XFR_SIZE + * register which will cause missed DMA interrupt. We could try to + * use a timer for the callback, but it is unsafe as the XFR_SIZE + * register is corrupt, and we won't know if the DMA worked. + */ + if (dma_addr & 0x2) + return false; + + /* + * Because of HW issue #10, it seems like mixing sync DMA and async + * PIO access can confuse the DMA. Make sure XFR_SIZE is reset before + * using the channel for DMA. + */ + if (chdat->tx) + dma_remaining = musb_readl(ep_conf, TUSB_EP_TX_OFFSET); + else + dma_remaining = musb_readl(ep_conf, TUSB_EP_RX_OFFSET); + + dma_remaining = TUSB_EP_CONFIG_XFR_SIZE(dma_remaining); + if (dma_remaining) { + DBG(2, "Busy %s dma ch%i, not using: %08x\n", + chdat->tx ? "tx" : "rx", chdat->ch, + dma_remaining); + return false; + } + + chdat->transfer_len = len & ~0x1f; + + if (len < packet_sz) + chdat->transfer_packet_sz = chdat->transfer_len; + else + chdat->transfer_packet_sz = packet_sz; + + if (tusb_dma->multichannel) { + ch = chdat->ch; + dmareq = chdat->dmareq; + sync_dev = chdat->sync_dev; + } else { + if (tusb_omap_use_shared_dmareq(chdat) != 0) { + DBG(3, "could not get dma for ep%i\n", chdat->epnum); + return false; + } + if (tusb_dma->ch < 0) { + /* REVISIT: This should get blocked earlier, happens + * with MSC ErrorRecoveryTest + */ + WARN_ON(1); + return false; + } + + ch = tusb_dma->ch; + dmareq = tusb_dma->dmareq; + sync_dev = tusb_dma->sync_dev; + omap_set_dma_callback(ch, tusb_omap_dma_cb, channel); + } + + chdat->packet_sz = packet_sz; + chdat->len = len; + channel->actual_len = 0; + chdat->dma_addr = (void __iomem *)dma_addr; + channel->status = MUSB_DMA_STATUS_BUSY; + + /* Since we're recycling dma areas, we need to clean or invalidate */ + if (chdat->tx) + dma_cache_maint(phys_to_virt(dma_addr), len, DMA_TO_DEVICE); + else + dma_cache_maint(phys_to_virt(dma_addr), len, DMA_FROM_DEVICE); + + /* Use 16-bit transfer if dma_addr is not 32-bit aligned */ + if ((dma_addr & 0x3) == 0) { + dma_params.data_type = OMAP_DMA_DATA_TYPE_S32; + dma_params.elem_count = 8; /* Elements in frame */ + } else { + dma_params.data_type = OMAP_DMA_DATA_TYPE_S16; + dma_params.elem_count = 16; /* Elements in frame */ + fifo = hw_ep->fifo_async; + } + + dma_params.frame_count = chdat->transfer_len / 32; /* Burst sz frame */ + + DBG(3, "ep%i %s dma ch%i dma: %08x len: %u(%u) packet_sz: %i(%i)\n", + chdat->epnum, chdat->tx ? "tx" : "rx", + ch, dma_addr, chdat->transfer_len, len, + chdat->transfer_packet_sz, packet_sz); + + /* + * Prepare omap DMA for transfer + */ + if (chdat->tx) { + dma_params.src_amode = OMAP_DMA_AMODE_POST_INC; + dma_params.src_start = (unsigned long)dma_addr; + dma_params.src_ei = 0; + dma_params.src_fi = 0; + + dma_params.dst_amode = OMAP_DMA_AMODE_DOUBLE_IDX; + dma_params.dst_start = (unsigned long)fifo; + dma_params.dst_ei = 1; + dma_params.dst_fi = -31; /* Loop 32 byte window */ + + dma_params.trigger = sync_dev; + dma_params.sync_mode = OMAP_DMA_SYNC_FRAME; + dma_params.src_or_dst_synch = 0; /* Dest sync */ + + src_burst = OMAP_DMA_DATA_BURST_16; /* 16x32 read */ + dst_burst = OMAP_DMA_DATA_BURST_8; /* 8x32 write */ + } else { + dma_params.src_amode = OMAP_DMA_AMODE_DOUBLE_IDX; + dma_params.src_start = (unsigned long)fifo; + dma_params.src_ei = 1; + dma_params.src_fi = -31; /* Loop 32 byte window */ + + dma_params.dst_amode = OMAP_DMA_AMODE_POST_INC; + dma_params.dst_start = (unsigned long)dma_addr; + dma_params.dst_ei = 0; + dma_params.dst_fi = 0; + + dma_params.trigger = sync_dev; + dma_params.sync_mode = OMAP_DMA_SYNC_FRAME; + dma_params.src_or_dst_synch = 1; /* Source sync */ + + src_burst = OMAP_DMA_DATA_BURST_8; /* 8x32 read */ + dst_burst = OMAP_DMA_DATA_BURST_16; /* 16x32 write */ + } + + DBG(3, "ep%i %s using %i-bit %s dma from 0x%08lx to 0x%08lx\n", + chdat->epnum, chdat->tx ? "tx" : "rx", + (dma_params.data_type == OMAP_DMA_DATA_TYPE_S32) ? 32 : 16, + ((dma_addr & 0x3) == 0) ? "sync" : "async", + dma_params.src_start, dma_params.dst_start); + + omap_set_dma_params(ch, &dma_params); + omap_set_dma_src_burst_mode(ch, src_burst); + omap_set_dma_dest_burst_mode(ch, dst_burst); + omap_set_dma_write_mode(ch, OMAP_DMA_WRITE_LAST_NON_POSTED); + + /* + * Prepare MUSB for DMA transfer + */ + if (chdat->tx) { + musb_ep_select(mbase, chdat->epnum); + csr = musb_readw(hw_ep->regs, MUSB_TXCSR); + csr |= (MUSB_TXCSR_AUTOSET | MUSB_TXCSR_DMAENAB + | MUSB_TXCSR_DMAMODE | MUSB_TXCSR_MODE); + csr &= ~MUSB_TXCSR_P_UNDERRUN; + musb_writew(hw_ep->regs, MUSB_TXCSR, csr); + } else { + musb_ep_select(mbase, chdat->epnum); + csr = musb_readw(hw_ep->regs, MUSB_RXCSR); + csr |= MUSB_RXCSR_DMAENAB; + csr &= ~(MUSB_RXCSR_AUTOCLEAR | MUSB_RXCSR_DMAMODE); + musb_writew(hw_ep->regs, MUSB_RXCSR, + csr | MUSB_RXCSR_P_WZC_BITS); + } + + /* + * Start DMA transfer + */ + omap_start_dma(ch); + + if (chdat->tx) { + /* Send transfer_packet_sz packets at a time */ + musb_writel(ep_conf, TUSB_EP_MAX_PACKET_SIZE_OFFSET, + chdat->transfer_packet_sz); + + musb_writel(ep_conf, TUSB_EP_TX_OFFSET, + TUSB_EP_CONFIG_XFR_SIZE(chdat->transfer_len)); + } else { + /* Receive transfer_packet_sz packets at a time */ + musb_writel(ep_conf, TUSB_EP_MAX_PACKET_SIZE_OFFSET, + chdat->transfer_packet_sz << 16); + + musb_writel(ep_conf, TUSB_EP_RX_OFFSET, + TUSB_EP_CONFIG_XFR_SIZE(chdat->transfer_len)); + } + + return true; +} + +static int tusb_omap_dma_abort(struct dma_channel *channel) +{ + struct tusb_omap_dma_ch *chdat = to_chdat(channel); + struct tusb_omap_dma *tusb_dma = chdat->tusb_dma; + + if (!tusb_dma->multichannel) { + if (tusb_dma->ch >= 0) { + omap_stop_dma(tusb_dma->ch); + omap_free_dma(tusb_dma->ch); + tusb_dma->ch = -1; + } + + tusb_dma->dmareq = -1; + tusb_dma->sync_dev = -1; + } + + channel->status = MUSB_DMA_STATUS_FREE; + + return 0; +} + +static inline int tusb_omap_dma_allocate_dmareq(struct tusb_omap_dma_ch *chdat) +{ + u32 reg = musb_readl(chdat->tbase, TUSB_DMA_EP_MAP); + int i, dmareq_nr = -1; + + const int sync_dev[6] = { + OMAP24XX_DMA_EXT_DMAREQ0, + OMAP24XX_DMA_EXT_DMAREQ1, + OMAP242X_DMA_EXT_DMAREQ2, + OMAP242X_DMA_EXT_DMAREQ3, + OMAP242X_DMA_EXT_DMAREQ4, + OMAP242X_DMA_EXT_DMAREQ5, + }; + + for (i = 0; i < MAX_DMAREQ; i++) { + int cur = (reg & (0xf << (i * 5))) >> (i * 5); + if (cur == 0) { + dmareq_nr = i; + break; + } + } + + if (dmareq_nr == -1) + return -EAGAIN; + + reg |= (chdat->epnum << (dmareq_nr * 5)); + if (chdat->tx) + reg |= ((1 << 4) << (dmareq_nr * 5)); + musb_writel(chdat->tbase, TUSB_DMA_EP_MAP, reg); + + chdat->dmareq = dmareq_nr; + chdat->sync_dev = sync_dev[chdat->dmareq]; + + return 0; +} + +static inline void tusb_omap_dma_free_dmareq(struct tusb_omap_dma_ch *chdat) +{ + u32 reg; + + if (!chdat || chdat->dmareq < 0) + return; + + reg = musb_readl(chdat->tbase, TUSB_DMA_EP_MAP); + reg &= ~(0x1f << (chdat->dmareq * 5)); + musb_writel(chdat->tbase, TUSB_DMA_EP_MAP, reg); + + chdat->dmareq = -1; + chdat->sync_dev = -1; +} + +static struct dma_channel *dma_channel_pool[MAX_DMAREQ]; + +static struct dma_channel * +tusb_omap_dma_allocate(struct dma_controller *c, + struct musb_hw_ep *hw_ep, + u8 tx) +{ + int ret, i; + const char *dev_name; + struct tusb_omap_dma *tusb_dma; + struct musb *musb; + void __iomem *tbase; + struct dma_channel *channel = NULL; + struct tusb_omap_dma_ch *chdat = NULL; + u32 reg; + + tusb_dma = container_of(c, struct tusb_omap_dma, controller); + musb = tusb_dma->musb; + tbase = musb->ctrl_base; + + reg = musb_readl(tbase, TUSB_DMA_INT_MASK); + if (tx) + reg &= ~(1 << hw_ep->epnum); + else + reg &= ~(1 << (hw_ep->epnum + 15)); + musb_writel(tbase, TUSB_DMA_INT_MASK, reg); + + /* REVISIT: Why does dmareq5 not work? */ + if (hw_ep->epnum == 0) { + DBG(3, "Not allowing DMA for ep0 %s\n", tx ? "tx" : "rx"); + return NULL; + } + + for (i = 0; i < MAX_DMAREQ; i++) { + struct dma_channel *ch = dma_channel_pool[i]; + if (ch->status == MUSB_DMA_STATUS_UNKNOWN) { + ch->status = MUSB_DMA_STATUS_FREE; + channel = ch; + chdat = ch->private_data; + break; + } + } + + if (!channel) + return NULL; + + if (tx) { + chdat->tx = 1; + dev_name = "TUSB transmit"; + } else { + chdat->tx = 0; + dev_name = "TUSB receive"; + } + + chdat->musb = tusb_dma->musb; + chdat->tbase = tusb_dma->tbase; + chdat->hw_ep = hw_ep; + chdat->epnum = hw_ep->epnum; + chdat->dmareq = -1; + chdat->completed_len = 0; + chdat->tusb_dma = tusb_dma; + + channel->max_len = 0x7fffffff; + channel->desired_mode = 0; + channel->actual_len = 0; + + if (tusb_dma->multichannel) { + ret = tusb_omap_dma_allocate_dmareq(chdat); + if (ret != 0) + goto free_dmareq; + + ret = omap_request_dma(chdat->sync_dev, dev_name, + tusb_omap_dma_cb, channel, &chdat->ch); + if (ret != 0) + goto free_dmareq; + } else if (tusb_dma->ch == -1) { + tusb_dma->dmareq = 0; + tusb_dma->sync_dev = OMAP24XX_DMA_EXT_DMAREQ0; + + /* Callback data gets set later in the shared dmareq case */ + ret = omap_request_dma(tusb_dma->sync_dev, "TUSB shared", + tusb_omap_dma_cb, NULL, &tusb_dma->ch); + if (ret != 0) + goto free_dmareq; + + chdat->dmareq = -1; + chdat->ch = -1; + } + + DBG(3, "ep%i %s dma: %s dma%i dmareq%i sync%i\n", + chdat->epnum, + chdat->tx ? "tx" : "rx", + chdat->ch >= 0 ? "dedicated" : "shared", + chdat->ch >= 0 ? chdat->ch : tusb_dma->ch, + chdat->dmareq >= 0 ? chdat->dmareq : tusb_dma->dmareq, + chdat->sync_dev >= 0 ? chdat->sync_dev : tusb_dma->sync_dev); + + return channel; + +free_dmareq: + tusb_omap_dma_free_dmareq(chdat); + + DBG(3, "ep%i: Could not get a DMA channel\n", chdat->epnum); + channel->status = MUSB_DMA_STATUS_UNKNOWN; + + return NULL; +} + +static void tusb_omap_dma_release(struct dma_channel *channel) +{ + struct tusb_omap_dma_ch *chdat = to_chdat(channel); + struct musb *musb = chdat->musb; + void __iomem *tbase = musb->ctrl_base; + u32 reg; + + DBG(3, "ep%i ch%i\n", chdat->epnum, chdat->ch); + + reg = musb_readl(tbase, TUSB_DMA_INT_MASK); + if (chdat->tx) + reg |= (1 << chdat->epnum); + else + reg |= (1 << (chdat->epnum + 15)); + musb_writel(tbase, TUSB_DMA_INT_MASK, reg); + + reg = musb_readl(tbase, TUSB_DMA_INT_CLEAR); + if (chdat->tx) + reg |= (1 << chdat->epnum); + else + reg |= (1 << (chdat->epnum + 15)); + musb_writel(tbase, TUSB_DMA_INT_CLEAR, reg); + + channel->status = MUSB_DMA_STATUS_UNKNOWN; + + if (chdat->ch >= 0) { + omap_stop_dma(chdat->ch); + omap_free_dma(chdat->ch); + chdat->ch = -1; + } + + if (chdat->dmareq >= 0) + tusb_omap_dma_free_dmareq(chdat); + + channel = NULL; +} + +void dma_controller_destroy(struct dma_controller *c) +{ + struct tusb_omap_dma *tusb_dma; + int i; + + tusb_dma = container_of(c, struct tusb_omap_dma, controller); + for (i = 0; i < MAX_DMAREQ; i++) { + struct dma_channel *ch = dma_channel_pool[i]; + if (ch) { + kfree(ch->private_data); + kfree(ch); + } + } + + if (!tusb_dma->multichannel && tusb_dma && tusb_dma->ch >= 0) + omap_free_dma(tusb_dma->ch); + + kfree(tusb_dma); +} + +struct dma_controller *__init +dma_controller_create(struct musb *musb, void __iomem *base) +{ + void __iomem *tbase = musb->ctrl_base; + struct tusb_omap_dma *tusb_dma; + int i; + + /* REVISIT: Get dmareq lines used from board-*.c */ + + musb_writel(musb->ctrl_base, TUSB_DMA_INT_MASK, 0x7fffffff); + musb_writel(musb->ctrl_base, TUSB_DMA_EP_MAP, 0); + + musb_writel(tbase, TUSB_DMA_REQ_CONF, + TUSB_DMA_REQ_CONF_BURST_SIZE(2) + | TUSB_DMA_REQ_CONF_DMA_REQ_EN(0x3f) + | TUSB_DMA_REQ_CONF_DMA_REQ_ASSER(2)); + + tusb_dma = kzalloc(sizeof(struct tusb_omap_dma), GFP_KERNEL); + if (!tusb_dma) + goto cleanup; + + tusb_dma->musb = musb; + tusb_dma->tbase = musb->ctrl_base; + + tusb_dma->ch = -1; + tusb_dma->dmareq = -1; + tusb_dma->sync_dev = -1; + + tusb_dma->controller.start = tusb_omap_dma_start; + tusb_dma->controller.stop = tusb_omap_dma_stop; + tusb_dma->controller.channel_alloc = tusb_omap_dma_allocate; + tusb_dma->controller.channel_release = tusb_omap_dma_release; + tusb_dma->controller.channel_program = tusb_omap_dma_program; + tusb_dma->controller.channel_abort = tusb_omap_dma_abort; + + if (tusb_get_revision(musb) >= TUSB_REV_30) + tusb_dma->multichannel = 1; + + for (i = 0; i < MAX_DMAREQ; i++) { + struct dma_channel *ch; + struct tusb_omap_dma_ch *chdat; + + ch = kzalloc(sizeof(struct dma_channel), GFP_KERNEL); + if (!ch) + goto cleanup; + + dma_channel_pool[i] = ch; + + chdat = kzalloc(sizeof(struct tusb_omap_dma_ch), GFP_KERNEL); + if (!chdat) + goto cleanup; + + ch->status = MUSB_DMA_STATUS_UNKNOWN; + ch->private_data = chdat; + } + + return &tusb_dma->controller; + +cleanup: + dma_controller_destroy(&tusb_dma->controller); + + return NULL; +} diff --git a/include/linux/usb/musb.h b/include/linux/usb/musb.h new file mode 100644 index 00000000000..d325a0d5bf4 --- /dev/null +++ b/include/linux/usb/musb.h @@ -0,0 +1,70 @@ +/* + * This is used to for host and peripheral modes of the driver for + * Inventra (Multidrop) Highspeed Dual-Role Controllers: (M)HDRC. + * + * Board initialization should put one of these into dev->platform_data, + * probably on some platform_device named "musb_hdrc". It encapsulates + * key configuration differences between boards. + */ + +/* The USB role is defined by the connector used on the board, so long as + * standards are being followed. (Developer boards sometimes won't.) + */ +enum musb_mode { + MUSB_UNDEFINED = 0, + MUSB_HOST, /* A or Mini-A connector */ + MUSB_PERIPHERAL, /* B or Mini-B connector */ + MUSB_OTG /* Mini-AB connector */ +}; + +struct clk; + +struct musb_hdrc_platform_data { + /* MUSB_HOST, MUSB_PERIPHERAL, or MUSB_OTG */ + u8 mode; + + /* for clk_get() */ + const char *clock; + + /* (HOST or OTG) switch VBUS on/off */ + int (*set_vbus)(struct device *dev, int is_on); + + /* (HOST or OTG) mA/2 power supplied on (default = 8mA) */ + u8 power; + + /* (PERIPHERAL) mA/2 max power consumed (default = 100mA) */ + u8 min_power; + + /* (HOST or OTG) msec/2 after VBUS on till power good */ + u8 potpgt; + + /* TBD: chip defaults should probably go someplace else, + * e.g. number of tx/rx endpoints, etc + */ + unsigned multipoint:1; + + /* Power the device on or off */ + int (*set_power)(int state); + + /* Turn device clock on or off */ + int (*set_clock)(struct clk *clock, int is_on); +}; + + +/* TUSB 6010 support */ + +#define TUSB6010_OSCCLK_60 16667 /* psec/clk @ 60.0 MHz */ +#define TUSB6010_REFCLK_24 41667 /* psec/clk @ 24.0 MHz XI */ +#define TUSB6010_REFCLK_19 52083 /* psec/clk @ 19.2 MHz CLKIN */ + +#ifdef CONFIG_ARCH_OMAP2 + +extern int __init tusb6010_setup_interface( + struct musb_hdrc_platform_data *data, + unsigned ps_refclk, unsigned waitpin, + unsigned async_cs, unsigned sync_cs, + unsigned irq, unsigned dmachan); + +extern int tusb6010_platform_retime(unsigned is_refclk); + +#endif /* OMAP2 */ -- GitLab From f362a47560070ec0aaf68ac6b45901eeed1c844f Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Mon, 4 Aug 2008 13:53:52 +0300 Subject: [PATCH 317/750] usb: musb: fix hanging when rmmod gadget driver If we try to modprobe a second gadget driver before rmmoding the first one, the reference for the first gadget driver would get NULLed avoiding usb to change gadget drivers later. Cc: David Brownell Cc: Tony Lindgren Signed-off-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman --- drivers/usb/musb/musb_gadget.c | 16 +++++++--------- 1 file changed, 7 insertions(+), 9 deletions(-) diff --git a/drivers/usb/musb/musb_gadget.c b/drivers/usb/musb/musb_gadget.c index b3773f13ee0..d6a802c224f 100644 --- a/drivers/usb/musb/musb_gadget.c +++ b/drivers/usb/musb/musb_gadget.c @@ -1710,17 +1710,15 @@ int usb_gadget_register_driver(struct usb_gadget_driver *driver) spin_unlock_irqrestore(&musb->lock, flags); - if (retval == 0) + if (retval == 0) { retval = driver->bind(&musb->g); - if (retval != 0) { - DBG(3, "bind to driver %s failed --> %d\n", - driver->driver.name, retval); - musb->gadget_driver = NULL; - musb->g.dev.driver = NULL; - } + if (retval != 0) { + DBG(3, "bind to driver %s failed --> %d\n", + driver->driver.name, retval); + musb->gadget_driver = NULL; + musb->g.dev.driver = NULL; + } - /* start peripheral and/or OTG engines */ - if (retval == 0) { spin_lock_irqsave(&musb->lock, flags); /* REVISIT always use otg_set_peripheral(), handling -- GitLab From ca6d1b1333bc2e61e37982de1f28d8604c232414 Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Fri, 8 Aug 2008 12:40:54 +0300 Subject: [PATCH 318/750] usb: musb: pass configuration specifics via pdata Use platform_data to pass musb configuration-specific details to musb driver. This patch will prevent that other platforms selecting HAVE_CLK and enabling musb won't break tree building. The other parts of it will come when linux-omap merge up more omap2/3 board-files. Signed-off-by: Felipe Balbi Acked-by: Paul Mundt Signed-off-by: Greg Kroah-Hartman --- arch/arm/mach-omap2/usb-tusb6010.c | 1 - drivers/usb/musb/musb_core.c | 37 +++---- drivers/usb/musb/musb_core.h | 14 +-- drivers/usb/musb/tusb6010.h | 169 ----------------------------- include/linux/usb/musb.h | 38 ++++++- 5 files changed, 51 insertions(+), 208 deletions(-) diff --git a/arch/arm/mach-omap2/usb-tusb6010.c b/arch/arm/mach-omap2/usb-tusb6010.c index 1607c941d95..10ef464d6be 100644 --- a/arch/arm/mach-omap2/usb-tusb6010.c +++ b/arch/arm/mach-omap2/usb-tusb6010.c @@ -317,7 +317,6 @@ tusb6010_setup_interface(struct musb_hdrc_platform_data *data, printk(error, 6, status); return -ENODEV; } - data->multipoint = 1; tusb_device.dev.platform_data = data; /* REVISIT let the driver know what DMA channels work */ diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c index 462586d06da..d68ec6daf33 100644 --- a/drivers/usb/musb/musb_core.c +++ b/drivers/usb/musb/musb_core.c @@ -990,12 +990,6 @@ static void musb_shutdown(struct platform_device *pdev) * We don't currently use dynamic fifo setup capability to do anything * more than selecting one of a bunch of predefined configurations. */ -#ifdef MUSB_C_DYNFIFO_DEF -#define can_dynfifo() 1 -#else -#define can_dynfifo() 0 -#endif - #if defined(CONFIG_USB_TUSB6010) || \ defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP34XX) static ushort __initdata fifo_mode = 4; @@ -1008,8 +1002,6 @@ module_param(fifo_mode, ushort, 0); MODULE_PARM_DESC(fifo_mode, "initial endpoint configuration"); -#define DYN_FIFO_SIZE (1<<(MUSB_C_RAM_BITS+2)) - enum fifo_style { FIFO_RXTX, FIFO_TX, FIFO_RX } __attribute__ ((packed)); enum buf_mode { BUF_SINGLE, BUF_DOUBLE } __attribute__ ((packed)); @@ -1119,11 +1111,12 @@ fifo_setup(struct musb *musb, struct musb_hw_ep *hw_ep, c_size = size - 3; if (cfg->mode == BUF_DOUBLE) { - if ((offset + (maxpacket << 1)) > DYN_FIFO_SIZE) + if ((offset + (maxpacket << 1)) > + (1 << (musb->config->ram_bits + 2))) return -EMSGSIZE; c_size |= MUSB_FIFOSZ_DPB; } else { - if ((offset + maxpacket) > DYN_FIFO_SIZE) + if ((offset + maxpacket) > (1 << (musb->config->ram_bits + 2))) return -EMSGSIZE; } @@ -1219,13 +1212,13 @@ static int __init ep_config_from_table(struct musb *musb) /* assert(offset > 0) */ /* NOTE: for RTL versions >= 1.400 EPINFO and RAMINFO would - * be better than static MUSB_C_NUM_EPS and DYN_FIFO_SIZE... + * be better than static musb->config->num_eps and DYN_FIFO_SIZE... */ for (i = 0; i < n; i++) { u8 epn = cfg->hw_ep_num; - if (epn >= MUSB_C_NUM_EPS) { + if (epn >= musb->config->num_eps) { pr_debug("%s: invalid ep %d\n", musb_driver_name, epn); continue; @@ -1242,8 +1235,8 @@ static int __init ep_config_from_table(struct musb *musb) printk(KERN_DEBUG "%s: %d/%d max ep, %d/%d memory\n", musb_driver_name, - n + 1, MUSB_C_NUM_EPS * 2 - 1, - offset, DYN_FIFO_SIZE); + n + 1, musb->config->num_eps * 2 - 1, + offset, (1 << (musb->config->ram_bits + 2))); #ifdef CONFIG_USB_MUSB_HDRC_HCD if (!musb->bulk_ep) { @@ -1270,7 +1263,7 @@ static int __init ep_config_from_hw(struct musb *musb) /* FIXME pick up ep0 maxpacket size */ - for (epnum = 1; epnum < MUSB_C_NUM_EPS; epnum++) { + for (epnum = 1; epnum < musb->config->num_eps; epnum++) { musb_ep_select(mbase, epnum); hw_ep = musb->endpoints + epnum; @@ -1424,14 +1417,14 @@ static int __init musb_core_init(u16 musb_type, struct musb *musb) musb->epmask = 1; if (reg & MUSB_CONFIGDATA_DYNFIFO) { - if (can_dynfifo()) + if (musb->config->dyn_fifo) status = ep_config_from_table(musb); else { ERR("reconfigure software for Dynamic FIFOs\n"); status = -ENODEV; } } else { - if (!can_dynfifo()) + if (!musb->config->dyn_fifo) status = ep_config_from_hw(musb); else { ERR("reconfigure software for static FIFOs\n"); @@ -1788,7 +1781,8 @@ static void musb_irq_work(struct work_struct *data) */ static struct musb *__init -allocate_instance(struct device *dev, void __iomem *mbase) +allocate_instance(struct device *dev, + struct musb_hdrc_config *config, void __iomem *mbase) { struct musb *musb; struct musb_hw_ep *ep; @@ -1820,8 +1814,9 @@ allocate_instance(struct device *dev, void __iomem *mbase) musb->mregs = mbase; musb->ctrl_base = mbase; musb->nIrq = -ENODEV; + musb->config = config; for (epnum = 0, ep = musb->endpoints; - epnum < MUSB_C_NUM_EPS; + epnum < musb->config->num_eps; epnum++, ep++) { ep->musb = musb; @@ -1929,7 +1924,7 @@ bad_config: } /* allocate */ - musb = allocate_instance(dev, ctrl); + musb = allocate_instance(dev, plat->config, ctrl); if (!musb) return -ENOMEM; @@ -1987,7 +1982,7 @@ bad_config: musb_generic_disable(musb); /* setup musb parts of the core (especially endpoints) */ - status = musb_core_init(plat->multipoint + status = musb_core_init(plat->config->multipoint ? MUSB_CONTROLLER_MHDRC : MUSB_CONTROLLER_HDRC, musb); if (status < 0) diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h index 90035c12ab5..eade46d8170 100644 --- a/drivers/usb/musb/musb_core.h +++ b/drivers/usb/musb/musb_core.h @@ -56,18 +56,6 @@ struct musb_ep; #include "musb_debug.h" #include "musb_dma.h" -#ifdef CONFIG_USB_MUSB_SOC -/* - * Get core configuration from a header converted (by cfg_conv) - * from the Verilog config file generated by the core config utility - * - * For now we assume that header is provided along with other - * arch-specific files. Discrete chips will need a build tweak. - * So will using AHB IDs from silicon that provides them. - */ -#include -#endif - #include "musb_io.h" #include "musb_regs.h" @@ -440,6 +428,8 @@ struct musb { struct usb_gadget_driver *gadget_driver; /* its driver */ #endif + struct musb_hdrc_config *config; + #ifdef MUSB_CONFIG_PROC_FS struct proc_dir_entry *proc_entry; #endif diff --git a/drivers/usb/musb/tusb6010.h b/drivers/usb/musb/tusb6010.h index db6dad0750a..ab8c96286ce 100644 --- a/drivers/usb/musb/tusb6010.h +++ b/drivers/usb/musb/tusb6010.h @@ -230,173 +230,4 @@ extern u8 tusb_get_revision(struct musb *musb); #define TUSB_REV_30 0x30 #define TUSB_REV_31 0x31 -/*----------------------------------------------------------------------------*/ - -#ifdef CONFIG_USB_TUSB6010 - -/* configuration parameters specific to this silicon */ - -/* Number of Tx endpoints. Legal values are 1 - 16 (this value includes EP0) */ -#define MUSB_C_NUM_EPT 16 - -/* Number of Rx endpoints. Legal values are 1 - 16 (this value includes EP0) */ -#define MUSB_C_NUM_EPR 16 - -/* Endpoint 1 to 15 direction types. C_EP1_DEF is defined if either Tx endpoint - * 1 or Rx endpoint 1 are used. - */ -#define MUSB_C_EP1_DEF - -/* C_EP1_TX_DEF is defined if Tx endpoint 1 is used */ -#define MUSB_C_EP1_TX_DEF - -/* C_EP1_RX_DEF is defined if Rx endpoint 1 is used */ -#define MUSB_C_EP1_RX_DEF - -/* C_EP1_TOR_DEF is defined if Tx endpoint 1 and Rx endpoint 1 share a FIFO */ -/* #define C_EP1_TOR_DEF */ - -/* C_EP1_TAR_DEF is defined if both Tx endpoint 1 and Rx endpoint 1 are used - * and do not share a FIFO. - */ -#define MUSB_C_EP1_TAR_DEF - -/* Similarly for all other used endpoints */ -#define MUSB_C_EP2_DEF -#define MUSB_C_EP2_TX_DEF -#define MUSB_C_EP2_RX_DEF -#define MUSB_C_EP2_TAR_DEF -#define MUSB_C_EP3_DEF -#define MUSB_C_EP3_TX_DEF -#define MUSB_C_EP3_RX_DEF -#define MUSB_C_EP3_TAR_DEF -#define MUSB_C_EP4_DEF -#define MUSB_C_EP4_TX_DEF -#define MUSB_C_EP4_RX_DEF -#define MUSB_C_EP4_TAR_DEF - -/* Endpoint 1 to 15 FIFO address bits. Legal values are 3 to 13 - corresponding - * to FIFO sizes of 8 to 8192 bytes. If an Tx endpoint shares a FIFO with an Rx - * endpoint then the Rx FIFO size must be the same as the Tx FIFO size. All - * endpoints 1 to 15 must be defined, unused endpoints should be set to 2. - */ -#define MUSB_C_EP1T_BITS 5 -#define MUSB_C_EP1R_BITS 5 -#define MUSB_C_EP2T_BITS 5 -#define MUSB_C_EP2R_BITS 5 -#define MUSB_C_EP3T_BITS 3 -#define MUSB_C_EP3R_BITS 3 -#define MUSB_C_EP4T_BITS 3 -#define MUSB_C_EP4R_BITS 3 - -#define MUSB_C_EP5T_BITS 2 -#define MUSB_C_EP5R_BITS 2 -#define MUSB_C_EP6T_BITS 2 -#define MUSB_C_EP6R_BITS 2 -#define MUSB_C_EP7T_BITS 2 -#define MUSB_C_EP7R_BITS 2 -#define MUSB_C_EP8T_BITS 2 -#define MUSB_C_EP8R_BITS 2 -#define MUSB_C_EP9T_BITS 2 -#define MUSB_C_EP9R_BITS 2 -#define MUSB_C_EP10T_BITS 2 -#define MUSB_C_EP10R_BITS 2 -#define MUSB_C_EP11T_BITS 2 -#define MUSB_C_EP11R_BITS 2 -#define MUSB_C_EP12T_BITS 2 -#define MUSB_C_EP12R_BITS 2 -#define MUSB_C_EP13T_BITS 2 -#define MUSB_C_EP13R_BITS 2 -#define MUSB_C_EP14T_BITS 2 -#define MUSB_C_EP14R_BITS 2 -#define MUSB_C_EP15T_BITS 2 -#define MUSB_C_EP15R_BITS 2 - -/* Define the following constant if the USB2.0 Transceiver Macrocell data width - * is 16-bits. - */ -/* #define C_UTM_16 */ - -/* Define this constant if the CPU uses big-endian byte ordering. */ -/* #define C_BIGEND */ - -/* Define the following constant if any Tx endpoint is required to support - * multiple bulk packets. - */ -/* #define C_MP_TX */ - -/* Define the following constant if any Rx endpoint is required to support - * multiple bulk packets. - */ -/* #define C_MP_RX */ - -/* Define the following constant if any Tx endpoint is required to support high - * bandwidth ISO. - */ -/* #define C_HB_TX */ - -/* Define the following constant if any Rx endpoint is required to support high - * bandwidth ISO. - */ -/* #define C_HB_RX */ - -/* Define the following constant if software connect/disconnect control is - * required. - */ -#define MUSB_C_SOFT_CON - -/* Define the following constant if Vendor Control Registers are required. */ -/* #define C_VEND_REG */ - -/* Vendor control register widths. */ -#define MUSB_C_VCTL_BITS 4 -#define MUSB_C_VSTAT_BITS 8 - -/* Define the following constant to include a DMA controller. */ -/* #define C_DMA */ - -/* Define the following constant if 2 or more DMA channels are required. */ -/* #define C_DMA2 */ - -/* Define the following constant if 3 or more DMA channels are required. */ -/* #define C_DMA3 */ - -/* Define the following constant if 4 or more DMA channels are required. */ -/* #define C_DMA4 */ - -/* Define the following constant if 5 or more DMA channels are required. */ -/* #define C_DMA5 */ - -/* Define the following constant if 6 or more DMA channels are required. */ -/* #define C_DMA6 */ - -/* Define the following constant if 7 or more DMA channels are required. */ -/* #define C_DMA7 */ - -/* Define the following constant if 8 or more DMA channels are required. */ -/* #define C_DMA8 */ - -/* Enable Dynamic FIFO Sizing */ -#define MUSB_C_DYNFIFO_DEF - -/* Derived constants. The following constants are derived from the previous - * configuration constants - */ - -/* Total number of endpoints. Legal values are 2 - 16. This must be equal to - * the larger of C_NUM_EPT, C_NUM_EPR - */ -/* #define MUSB_C_NUM_EPS 5 */ - -/* C_EPMAX_BITS is equal to the largest endpoint FIFO word address bits */ -#define MUSB_C_EPMAX_BITS 11 - -/* C_RAM_BITS is the number of address bits required to address the RAM (32-bit - * addresses). It is defined as log2 of the sum of 2** of all the endpoint FIFO - * dword address bits (rounded up). - */ -#define MUSB_C_RAM_BITS 12 - -#endif /* CONFIG_USB_TUSB6010 */ - #endif /* __TUSB6010_H__ */ diff --git a/include/linux/usb/musb.h b/include/linux/usb/musb.h index d325a0d5bf4..630962c04ca 100644 --- a/include/linux/usb/musb.h +++ b/include/linux/usb/musb.h @@ -19,6 +19,36 @@ enum musb_mode { struct clk; +struct musb_hdrc_eps_bits { + const char name[16]; + u8 bits; +}; + +struct musb_hdrc_config { + /* MUSB configuration-specific details */ + unsigned multipoint:1; /* multipoint device */ + unsigned dyn_fifo:1; /* supports dynamic fifo sizing */ + unsigned soft_con:1; /* soft connect required */ + unsigned utm_16:1; /* utm data witdh is 16 bits */ + unsigned big_endian:1; /* true if CPU uses big-endian */ + unsigned mult_bulk_tx:1; /* Tx ep required for multbulk pkts */ + unsigned mult_bulk_rx:1; /* Rx ep required for multbulk pkts */ + unsigned high_iso_tx:1; /* Tx ep required for HB iso */ + unsigned high_iso_rx:1; /* Rx ep required for HD iso */ + unsigned dma:1; /* supports DMA */ + unsigned vendor_req:1; /* vendor registers required */ + + u8 num_eps; /* number of endpoints _with_ ep0 */ + u8 dma_channels; /* number of dma channels */ + u8 dyn_fifo_size; /* dynamic size in bytes */ + u8 vendor_ctrl; /* vendor control reg width */ + u8 vendor_stat; /* vendor status reg witdh */ + u8 dma_req_chan; /* bitmask for required dma channels */ + u8 ram_bits; /* ram address size */ + + struct musb_hdrc_eps_bits *eps_bits; +}; + struct musb_hdrc_platform_data { /* MUSB_HOST, MUSB_PERIPHERAL, or MUSB_OTG */ u8 mode; @@ -38,16 +68,14 @@ struct musb_hdrc_platform_data { /* (HOST or OTG) msec/2 after VBUS on till power good */ u8 potpgt; - /* TBD: chip defaults should probably go someplace else, - * e.g. number of tx/rx endpoints, etc - */ - unsigned multipoint:1; - /* Power the device on or off */ int (*set_power)(int state); /* Turn device clock on or off */ int (*set_clock)(struct clk *clock, int is_on); + + /* MUSB configuration-specific details */ + struct musb_hdrc_config *config; }; -- GitLab From ad661334b8ae421154b121ee6ad3b56807adbf11 Mon Sep 17 00:00:00 2001 From: Steve French Date: Tue, 12 Aug 2008 14:14:40 +0000 Subject: [PATCH 319/750] [CIFS] mount of IPC$ breaks with iget patch In looking at network named pipe support on cifs, I noticed that Dave Howell's iget patch: iget: stop CIFS from using iget() and read_inode() broke mounts to IPC$ (the interprocess communication share), and don't handle the error case (when getting info on the root inode fails). Thanks to Gunter who noted a typo in a debug line in the original version of this patch. CC: David Howells CC: Gunter Kukkukk CC: Stable Kernel Signed-off-by: Steve French --- fs/cifs/inode.c | 1 + 1 file changed, 1 insertion(+) diff --git a/fs/cifs/inode.c b/fs/cifs/inode.c index 28a22092d45..848286861c3 100644 --- a/fs/cifs/inode.c +++ b/fs/cifs/inode.c @@ -649,6 +649,7 @@ struct inode *cifs_iget(struct super_block *sb, unsigned long ino) inode->i_fop = &simple_dir_operations; inode->i_uid = cifs_sb->mnt_uid; inode->i_gid = cifs_sb->mnt_gid; + } else if (rc) { _FreeXid(xid); iget_failed(inode); return ERR_PTR(rc); -- GitLab From 8d5636fbca202f61fdb808fc9e20c0142291d802 Mon Sep 17 00:00:00 2001 From: Jeremy Kerr Date: Thu, 14 Aug 2008 14:59:12 +1000 Subject: [PATCH 320/750] powerpc/spufs: reference context while dropping state mutex in scheduler Based on an original patch from Christoph Hellwig . Currently, there is a possible reference-after-free in the spusched code - contexts may be freed after we have released their state_mutex in spusched_tick and find_victim. This change takes a reference to the context before releasing the mutex, so that the context doesn't get destroyed. Signed-off-by: Jeremy Kerr --- arch/powerpc/platforms/cell/spufs/sched.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) diff --git a/arch/powerpc/platforms/cell/spufs/sched.c b/arch/powerpc/platforms/cell/spufs/sched.c index 2deeeba7ecc..4b6b0c3a8c9 100644 --- a/arch/powerpc/platforms/cell/spufs/sched.c +++ b/arch/powerpc/platforms/cell/spufs/sched.c @@ -641,8 +641,10 @@ static struct spu *find_victim(struct spu_context *ctx) if (tmp && tmp->prio > ctx->prio && !(tmp->flags & SPU_CREATE_NOSCHED) && - (!victim || tmp->prio > victim->prio)) + (!victim || tmp->prio > victim->prio)) { victim = spu->ctx; + get_spu_context(victim); + } } mutex_unlock(&cbe_spu_info[node].list_mutex); @@ -658,6 +660,7 @@ static struct spu *find_victim(struct spu_context *ctx) * look at another context or give up after X retries. */ if (!mutex_trylock(&victim->state_mutex)) { + put_spu_context(victim); victim = NULL; goto restart; } @@ -670,6 +673,7 @@ static struct spu *find_victim(struct spu_context *ctx) * restart the search. */ mutex_unlock(&victim->state_mutex); + put_spu_context(victim); victim = NULL; goto restart; } @@ -687,6 +691,7 @@ static struct spu *find_victim(struct spu_context *ctx) spu_add_to_rq(victim); mutex_unlock(&victim->state_mutex); + put_spu_context(victim); return spu; } @@ -985,9 +990,11 @@ static int spusched_thread(void *unused) struct spu_context *ctx = spu->ctx; if (ctx) { + get_spu_context(ctx); mutex_unlock(mtx); spusched_tick(ctx); mutex_lock(mtx); + put_spu_context(ctx); } } mutex_unlock(mtx); -- GitLab From 0e06b50dda5965e0f8a15b0be14b759ead54fd2a Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Thu, 14 Aug 2008 14:29:57 +0800 Subject: [PATCH 321/750] Blackfin arch: cleanup cache lock code - remove cheesy read_iloc() function - move invalidate_entire_icache function to lock.S - export proper prototypes for functions in lock.S - only build lock.S when BFIN_ICACHE_LOCK is enabled Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- arch/blackfin/kernel/setup.c | 2 +- arch/blackfin/mach-common/Makefile | 3 +- arch/blackfin/mach-common/lock.S | 45 ++++++++++++++++++++---------- include/asm-blackfin/bfin-global.h | 6 +++- 4 files changed, 39 insertions(+), 17 deletions(-) diff --git a/arch/blackfin/kernel/setup.c b/arch/blackfin/kernel/setup.c index 936c06d820d..2ae84fea89e 100644 --- a/arch/blackfin/kernel/setup.c +++ b/arch/blackfin/kernel/setup.c @@ -1059,7 +1059,7 @@ static int show_cpuinfo(struct seq_file *m, void *v) dsup_banks, BFIN_DSUBBANKS, BFIN_DWAYS, BFIN_DLINES); #ifdef CONFIG_BFIN_ICACHE_LOCK - switch (read_iloc()) { + switch ((bfin_read_IMEM_CONTROL() >> 3) & WAYALL_L) { case WAY0_L: seq_printf(m, "Way0 Locked-Down\n"); break; diff --git a/arch/blackfin/mach-common/Makefile b/arch/blackfin/mach-common/Makefile index 862cd73c950..e6ed57c56d4 100644 --- a/arch/blackfin/mach-common/Makefile +++ b/arch/blackfin/mach-common/Makefile @@ -4,8 +4,9 @@ obj-y := \ cache.o entry.o head.o \ - interrupt.o lock.o irqpanic.o arch_checks.o ints-priority.o + interrupt.o irqpanic.o arch_checks.o ints-priority.o +obj-$(CONFIG_BFIN_ICACHE_LOCK) += lock.o obj-$(CONFIG_PM) += pm.o dpmc_modes.o obj-$(CONFIG_CPU_FREQ) += cpufreq.o obj-$(CONFIG_CPU_VOLTAGE) += dpmc.o diff --git a/arch/blackfin/mach-common/lock.S b/arch/blackfin/mach-common/lock.S index 30b887e67dd..9daf01201e9 100644 --- a/arch/blackfin/mach-common/lock.S +++ b/arch/blackfin/mach-common/lock.S @@ -28,13 +28,10 @@ */ #include -#include #include .text -#ifdef CONFIG_BFIN_ICACHE_LOCK - /* When you come here, it is assumed that * R0 - Which way to be locked */ @@ -189,18 +186,38 @@ ENTRY(_cache_lock) RTS; ENDPROC(_cache_lock) -#endif /* BFIN_ICACHE_LOCK */ - -/* Return the ILOC bits of IMEM_CONTROL +/* Invalidate the Entire Instruction cache by + * disabling IMC bit */ +ENTRY(_invalidate_entire_icache) + [--SP] = ( R7:5); -ENTRY(_read_iloc) - P1.H = HI(IMEM_CONTROL); - P1.L = LO(IMEM_CONTROL); - R1 = 0xF; - R0 = [P1]; - R0 = R0 >> 3; - R0 = R0 & R1; + P0.L = LO(IMEM_CONTROL); + P0.H = HI(IMEM_CONTROL); + R7 = [P0]; + + /* Clear the IMC bit , All valid bits in the instruction + * cache are set to the invalid state + */ + BITCLR(R7,IMC_P); + CLI R6; + SSYNC; /* SSYNC required before invalidating cache. */ + .align 8; + [P0] = R7; + SSYNC; + STI R6; + + /* Configures the instruction cache agian */ + R6 = (IMC | ENICPLB); + R7 = R7 | R6; + + CLI R6; + SSYNC; /* SSYNC required before writing to IMEM_CONTROL. */ + .align 8; + [P0] = R7; + SSYNC; + STI R6; + ( R7:5) = [SP++]; RTS; -ENDPROC(_read_iloc) +ENDPROC(_invalidate_entire_icache) diff --git a/include/asm-blackfin/bfin-global.h b/include/asm-blackfin/bfin-global.h index 93ae5335e8a..78eb389d200 100644 --- a/include/asm-blackfin/bfin-global.h +++ b/include/asm-blackfin/bfin-global.h @@ -62,7 +62,6 @@ extern void _cplb_hdr(void); /* Blackfin cache functions */ extern void bfin_icache_init(void); extern void bfin_dcache_init(void); -extern int read_iloc(void); extern int bfin_console_init(void); extern asmlinkage void lower_to_irq14(void); extern asmlinkage void bfin_return_from_exception(void); @@ -126,6 +125,11 @@ extern char _stext_l1[], _etext_l1[], _sdata_l1[], _edata_l1[], _sbss_l1[], /* only used when CONFIG_MTD_UCLINUX */ extern unsigned long memory_mtd_start, memory_mtd_end, mtd_size; +#ifdef CONFIG_BFIN_ICACHE_LOCK +extern void cache_grab_lock(int way); +extern void cache_lock(int way); +#endif + #endif #endif /* _BLACKFIN_H_ */ -- GitLab From 7ab37da52db98ea9f272045c837058dfc1870ac3 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Thu, 14 Aug 2008 14:33:05 +0800 Subject: [PATCH 322/750] Blackfin arch: delete dead prototypes Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- include/asm-blackfin/bfin-global.h | 5 ----- 1 file changed, 5 deletions(-) diff --git a/include/asm-blackfin/bfin-global.h b/include/asm-blackfin/bfin-global.h index 78eb389d200..8918cea3116 100644 --- a/include/asm-blackfin/bfin-global.h +++ b/include/asm-blackfin/bfin-global.h @@ -58,11 +58,9 @@ extern void dump_bfin_trace_buffer(void); extern int init_arch_irq(void); extern void bfin_reset(void); -extern void _cplb_hdr(void); /* Blackfin cache functions */ extern void bfin_icache_init(void); extern void bfin_dcache_init(void); -extern int bfin_console_init(void); extern asmlinkage void lower_to_irq14(void); extern asmlinkage void bfin_return_from_exception(void); extern void init_exception_vectors(void); @@ -70,7 +68,6 @@ extern void init_dma(void); extern void program_IAR(void); extern void evt14_softirq(void); extern asmlinkage void asm_do_IRQ(unsigned int irq, struct pt_regs *regs); -extern void bfin_gpio_interrupt_setup(int irq, int irq_pfx, int type); extern int bfin_internal_set_wake(unsigned int irq, unsigned int state); extern asmlinkage void finish_atomic_sections (struct pt_regs *regs); @@ -109,12 +106,10 @@ extern void *sram_alloc_with_lsl(size_t, unsigned long); extern int sram_free_with_lsl(const void*); extern const char bfin_board_name[]; -extern unsigned long wall_jiffies; extern unsigned long bfin_sic_iwr[]; extern unsigned vr_wakeup; extern u16 _bfin_swrst; /* shadow for Software Reset Register (SWRST) */ -extern struct file_operations dpmc_fops; extern unsigned long _ramstart, _ramend, _rambase; extern unsigned long memory_start, memory_end, physical_mem_end; extern char _stext_l1[], _etext_l1[], _sdata_l1[], _edata_l1[], _sbss_l1[], -- GitLab From 9216bbc83826b77da9f2f396578c9d32b81e0d0b Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Thu, 14 Aug 2008 14:35:20 +0800 Subject: [PATCH 323/750] Blackfin arch: mark some functions as __init as they are only called from __init functions Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- arch/blackfin/kernel/cplb-mpu/cacheinit.c | 4 ++-- arch/blackfin/kernel/cplb-nompu/cacheinit.c | 4 ++-- arch/blackfin/mach-bf527/ints-priority.c | 2 +- arch/blackfin/mach-bf533/ints-priority.c | 2 +- arch/blackfin/mach-bf537/ints-priority.c | 2 +- arch/blackfin/mach-bf548/ints-priority.c | 2 +- arch/blackfin/mach-bf561/ints-priority.c | 2 +- 7 files changed, 9 insertions(+), 9 deletions(-) diff --git a/arch/blackfin/kernel/cplb-mpu/cacheinit.c b/arch/blackfin/kernel/cplb-mpu/cacheinit.c index 9eecfa40318..a8b712a24c5 100644 --- a/arch/blackfin/kernel/cplb-mpu/cacheinit.c +++ b/arch/blackfin/kernel/cplb-mpu/cacheinit.c @@ -25,7 +25,7 @@ #include #if defined(CONFIG_BFIN_ICACHE) -void bfin_icache_init(void) +void __init bfin_icache_init(void) { unsigned long ctrl; int i; @@ -43,7 +43,7 @@ void bfin_icache_init(void) #endif #if defined(CONFIG_BFIN_DCACHE) -void bfin_dcache_init(void) +void __init bfin_dcache_init(void) { unsigned long ctrl; int i; diff --git a/arch/blackfin/kernel/cplb-nompu/cacheinit.c b/arch/blackfin/kernel/cplb-nompu/cacheinit.c index 8a18399f607..bd0831592c2 100644 --- a/arch/blackfin/kernel/cplb-nompu/cacheinit.c +++ b/arch/blackfin/kernel/cplb-nompu/cacheinit.c @@ -25,7 +25,7 @@ #include #if defined(CONFIG_BFIN_ICACHE) -void bfin_icache_init(void) +void __init bfin_icache_init(void) { unsigned long *table = icplb_table; unsigned long ctrl; @@ -47,7 +47,7 @@ void bfin_icache_init(void) #endif #if defined(CONFIG_BFIN_DCACHE) -void bfin_dcache_init(void) +void __init bfin_dcache_init(void) { unsigned long *table = dcplb_table; unsigned long ctrl; diff --git a/arch/blackfin/mach-bf527/ints-priority.c b/arch/blackfin/mach-bf527/ints-priority.c index 1fa38979396..8a2367403d2 100644 --- a/arch/blackfin/mach-bf527/ints-priority.c +++ b/arch/blackfin/mach-bf527/ints-priority.c @@ -31,7 +31,7 @@ #include #include -void program_IAR(void) +void __init program_IAR(void) { /* Program the IAR0 Register with the configured priority */ bfin_write_SIC_IAR0(((CONFIG_IRQ_PLL_WAKEUP - 7) << IRQ_PLL_WAKEUP_POS) | diff --git a/arch/blackfin/mach-bf533/ints-priority.c b/arch/blackfin/mach-bf533/ints-priority.c index 7d79e0f9503..f51994b7a2b 100644 --- a/arch/blackfin/mach-bf533/ints-priority.c +++ b/arch/blackfin/mach-bf533/ints-priority.c @@ -31,7 +31,7 @@ #include #include -void program_IAR(void) +void __init program_IAR(void) { /* Program the IAR0 Register with the configured priority */ bfin_write_SIC_IAR0(((CONFIG_PLLWAKE_ERROR - 7) << PLLWAKE_ERROR_POS) | diff --git a/arch/blackfin/mach-bf537/ints-priority.c b/arch/blackfin/mach-bf537/ints-priority.c index a8b915f202e..b1300b3f181 100644 --- a/arch/blackfin/mach-bf537/ints-priority.c +++ b/arch/blackfin/mach-bf537/ints-priority.c @@ -31,7 +31,7 @@ #include #include -void program_IAR(void) +void __init program_IAR(void) { /* Program the IAR0 Register with the configured priority */ bfin_write_SIC_IAR0(((CONFIG_IRQ_PLL_WAKEUP - 7) << IRQ_PLL_WAKEUP_POS) | diff --git a/arch/blackfin/mach-bf548/ints-priority.c b/arch/blackfin/mach-bf548/ints-priority.c index 2665653cee3..9dd0fa3ac4d 100644 --- a/arch/blackfin/mach-bf548/ints-priority.c +++ b/arch/blackfin/mach-bf548/ints-priority.c @@ -31,7 +31,7 @@ #include #include -void program_IAR(void) +void __init program_IAR(void) { /* Program the IAR0 Register with the configured priority */ bfin_write_SIC_IAR0(((CONFIG_IRQ_PLL_WAKEUP - 7) << IRQ_PLL_WAKEUP_POS) | diff --git a/arch/blackfin/mach-bf561/ints-priority.c b/arch/blackfin/mach-bf561/ints-priority.c index 09b541b0f7c..9d2f2334472 100644 --- a/arch/blackfin/mach-bf561/ints-priority.c +++ b/arch/blackfin/mach-bf561/ints-priority.c @@ -31,7 +31,7 @@ #include #include -void program_IAR(void) +void __init program_IAR(void) { /* Program the IAR0 Register with the configured priority */ bfin_write_SICA_IAR0(((CONFIG_IRQ_PLL_WAKEUP - 7) << IRQ_PLL_WAKEUP_POS) | -- GitLab From 3c012eebf8869dd3118c21a73a2f8cc9e9c694ea Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Thu, 14 Aug 2008 14:36:15 +0800 Subject: [PATCH 324/750] Blackfin arch: move fixed code defines into fixed_code.h as very few things actually need to know these details Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- include/asm-blackfin/Kbuild | 2 +- include/asm-blackfin/bfin-global.h | 13 ------------- include/asm-blackfin/fixed_code.h | 24 ++++++++++++++++++++++++ 3 files changed, 25 insertions(+), 14 deletions(-) diff --git a/include/asm-blackfin/Kbuild b/include/asm-blackfin/Kbuild index 71f8fe78325..606ecfdcc96 100644 --- a/include/asm-blackfin/Kbuild +++ b/include/asm-blackfin/Kbuild @@ -1,3 +1,3 @@ include include/asm-generic/Kbuild.asm -header-y += fixed_code.h +unifdef-y += fixed_code.h diff --git a/include/asm-blackfin/bfin-global.h b/include/asm-blackfin/bfin-global.h index 8918cea3116..e61ffc0162b 100644 --- a/include/asm-blackfin/bfin-global.h +++ b/include/asm-blackfin/bfin-global.h @@ -70,19 +70,6 @@ extern void evt14_softirq(void); extern asmlinkage void asm_do_IRQ(unsigned int irq, struct pt_regs *regs); extern int bfin_internal_set_wake(unsigned int irq, unsigned int state); -extern asmlinkage void finish_atomic_sections (struct pt_regs *regs); -extern char fixed_code_start; -extern char fixed_code_end; -extern int atomic_xchg32(void); -extern int atomic_cas32(void); -extern int atomic_add32(void); -extern int atomic_sub32(void); -extern int atomic_ior32(void); -extern int atomic_and32(void); -extern int atomic_xor32(void); -extern void safe_user_instruction(void); -extern void sigreturn_stub(void); - extern void *l1_data_A_sram_alloc(size_t); extern void *l1_data_B_sram_alloc(size_t); extern void *l1_inst_sram_alloc(size_t); diff --git a/include/asm-blackfin/fixed_code.h b/include/asm-blackfin/fixed_code.h index 37db66c7030..32c4d495d84 100644 --- a/include/asm-blackfin/fixed_code.h +++ b/include/asm-blackfin/fixed_code.h @@ -1,6 +1,28 @@ /* This file defines the fixed addresses where userspace programs can find atomic code sequences. */ +#ifndef __BFIN_ASM_FIXED_CODE_H__ +#define __BFIN_ASM_FIXED_CODE_H__ + +#ifdef __KERNEL__ +#ifndef __ASSEMBLY__ +#include +#include +extern asmlinkage void finish_atomic_sections(struct pt_regs *regs); +extern char fixed_code_start; +extern char fixed_code_end; +extern int atomic_xchg32(void); +extern int atomic_cas32(void); +extern int atomic_add32(void); +extern int atomic_sub32(void); +extern int atomic_ior32(void); +extern int atomic_and32(void); +extern int atomic_xor32(void); +extern void safe_user_instruction(void); +extern void sigreturn_stub(void); +#endif +#endif + #define FIXED_CODE_START 0x400 #define SIGRETURN_STUB 0x400 @@ -20,3 +42,5 @@ #define SAFE_USER_INSTRUCTION 0x480 #define FIXED_CODE_END 0x490 + +#endif -- GitLab From ee32664da9531329b87aa5109e41e7cc73a04121 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Thu, 14 Aug 2008 14:37:32 +0800 Subject: [PATCH 325/750] Blackfin arch: shuffle related prototypes together -- no functional changes Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- include/asm-blackfin/bfin-global.h | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/include/asm-blackfin/bfin-global.h b/include/asm-blackfin/bfin-global.h index e61ffc0162b..7ba70de66f2 100644 --- a/include/asm-blackfin/bfin-global.h +++ b/include/asm-blackfin/bfin-global.h @@ -56,17 +56,17 @@ extern void dump_bfin_process(struct pt_regs *regs); extern void dump_bfin_mem(struct pt_regs *regs); extern void dump_bfin_trace_buffer(void); +/* init functions only */ extern int init_arch_irq(void); -extern void bfin_reset(void); -/* Blackfin cache functions */ extern void bfin_icache_init(void); extern void bfin_dcache_init(void); -extern asmlinkage void lower_to_irq14(void); -extern asmlinkage void bfin_return_from_exception(void); extern void init_exception_vectors(void); -extern void init_dma(void); extern void program_IAR(void); -extern void evt14_softirq(void); + +extern void bfin_reset(void); +extern asmlinkage void lower_to_irq14(void); +extern asmlinkage void bfin_return_from_exception(void); +extern asmlinkage void evt14_softirq(void); extern asmlinkage void asm_do_IRQ(unsigned int irq, struct pt_regs *regs); extern int bfin_internal_set_wake(unsigned int irq, unsigned int state); -- GitLab From cd8fb8df1458df7f3b99fd112e722b05f42c64d9 Mon Sep 17 00:00:00 2001 From: Robin Getz Date: Thu, 14 Aug 2008 14:44:33 +0800 Subject: [PATCH 326/750] Blackfin arch: Print out doublefault addresses, so debug can occur Signed-off-by: Robin Getz Signed-off-by: Bryan Wu --- arch/blackfin/kernel/setup.c | 7 ++++++- arch/blackfin/mach-common/head.S | 6 ++++++ 2 files changed, 12 insertions(+), 1 deletion(-) diff --git a/arch/blackfin/kernel/setup.c b/arch/blackfin/kernel/setup.c index 2ae84fea89e..eb300550e09 100644 --- a/arch/blackfin/kernel/setup.c +++ b/arch/blackfin/kernel/setup.c @@ -52,6 +52,7 @@ EXPORT_SYMBOL(mtd_size); #endif char __initdata command_line[COMMAND_LINE_SIZE]; +unsigned int __initdata *__retx; /* boot memmap, for parsing "memmap=" */ #define BFIN_MEMMAP_MAX 128 /* number of entries in bfin_memmap */ @@ -785,7 +786,11 @@ void __init setup_arch(char **cmdline_p) bfin_write_SWRST(DOUBLE_FAULT); if (_bfin_swrst & RESET_DOUBLE) - printk(KERN_INFO "Recovering from Double Fault event\n"); + /* + * don't decode the address, since you don't know if this + * kernel's symbol map is the same as the crashing kernel + */ + printk(KERN_INFO "Recovering from Double Fault event at %p\n", __retx); else if (_bfin_swrst & RESET_WDOG) printk(KERN_INFO "Recovering from Watchdog event\n"); else if (_bfin_swrst & RESET_SOFTWARE) diff --git a/arch/blackfin/mach-common/head.S b/arch/blackfin/mach-common/head.S index 2c69ad49894..fb7e2d42699 100644 --- a/arch/blackfin/mach-common/head.S +++ b/arch/blackfin/mach-common/head.S @@ -90,6 +90,12 @@ ENTRY(__start) [p0] = R0; SSYNC; + /* Save RETX, in case of doublefault */ + p0.l = ___retx; + p0.h = ___retx; + R0 = RETX; + [P0] = R0; + /* Let each Blackfin family do its own thing */ call _mach_early_start; -- GitLab From 251383c7c50cf17664a4d7d60d3a52d8827a0e11 Mon Sep 17 00:00:00 2001 From: Robin Getz Date: Thu, 14 Aug 2008 15:12:55 +0800 Subject: [PATCH 327/750] Blackfin arch: Allow ins functions to have a low latency version Signed-off-by: Robin Getz Signed-off-by: Bryan Wu --- arch/blackfin/Kconfig | 27 ++++++++++ arch/blackfin/lib/ins.S | 109 ++++++++++++++++++++++++++++++++++++++++ 2 files changed, 136 insertions(+) diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig index cc2add7e39e..ededf9319f3 100644 --- a/arch/blackfin/Kconfig +++ b/arch/blackfin/Kconfig @@ -622,6 +622,33 @@ config CPLB_SWITCH_TAB_L1 If enabled, the CPLB Switch Tables are linked into L1 data memory. (less latency) +comment "Speed Optimizations" +config BFIN_INS_LOWOVERHEAD + bool "ins[bwl] low overhead, higher interrupt latency" + default y + help + Reads on the Blackfin are speculative. In Blackfin terms, this means + they can be interrupted at any time (even after they have been issued + on to the external bus), and re-issued after the interrupt occurs. + For memory - this is not a big deal, since memory does not change if + it sees a read. + + If a FIFO is sitting on the end of the read, it will see two reads, + when the core only sees one since the FIFO receives both the read + which is cancelled (and not delivered to the core) and the one which + is re-issued (which is delivered to the core). + + To solve this, interrupts are turned off before reads occur to + I/O space. This option controls which the overhead/latency of + controlling interrupts during this time + "n" turns interrupts off every read + (higher overhead, but lower interrupt latency) + "y" turns interrupts off every loop + (low overhead, but longer interrupt latency) + + default behavior is to leave this set to on (type "Y"). If you are experiencing + interrupt latency issues, it is safe and OK to turn this off. + endmenu diff --git a/arch/blackfin/lib/ins.S b/arch/blackfin/lib/ins.S index eba2343b1b5..d60554dce87 100644 --- a/arch/blackfin/lib/ins.S +++ b/arch/blackfin/lib/ins.S @@ -33,7 +33,28 @@ .align 2 +/* + * Reads on the Blackfin are speculative. In Blackfin terms, this means they + * can be interrupted at any time (even after they have been issued on to the + * external bus), and re-issued after the interrupt occurs. + * + * If a FIFO is sitting on the end of the read, it will see two reads, + * when the core only sees one. The FIFO receives the read which is cancelled, + * and not delivered to the core. + * + * To solve this, interrupts are turned off before reads occur to I/O space. + * There are 3 versions of all these functions + * - turns interrupts off every read (higher overhead, but lower latency) + * - turns interrupts off every loop (low overhead, but longer latency) + * - DMA version, which do not suffer from this issue. DMA versions have + * different name (prefixed by dma_ ), and are located in + * ../kernel/bfin_dma_5xx.c + * Using the dma related functions are recommended for transfering large + * buffers in/out of FIFOs. + */ + ENTRY(_insl) +#ifdef CONFIG_BFIN_INS_LOWOVERHEAD P0 = R0; /* P0 = port */ cli R3; P1 = R1; /* P1 = address */ @@ -46,9 +67,26 @@ ENTRY(_insl) .Llong_loop_e: NOP; sti R3; RTS; +#else + P0 = R0; /* P0 = port */ + P1 = R1; /* P1 = address */ + P2 = R2; /* P2 = count */ + SSYNC; + LSETUP( .Llong_loop_s, .Llong_loop_e) LC0 = P2; +.Llong_loop_s: + CLI R3; + NOP; NOP; NOP; + R0 = [P0]; + [P1++] = R0; +.Llong_loop_e: + STI R3; + + RTS; +#endif ENDPROC(_insl) ENTRY(_insw) +#ifdef CONFIG_BFIN_INS_LOWOVERHEAD P0 = R0; /* P0 = port */ cli R3; P1 = R1; /* P1 = address */ @@ -61,9 +99,26 @@ ENTRY(_insw) .Lword_loop_e: NOP; sti R3; RTS; +#else + P0 = R0; /* P0 = port */ + P1 = R1; /* P1 = address */ + P2 = R2; /* P2 = count */ + SSYNC; + LSETUP( .Lword_loop_s, .Lword_loop_e) LC0 = P2; +.Lword_loop_s: + CLI R3; + NOP; NOP; NOP; + R0 = W[P0]; + W[P1++] = R0; +.Lword_loop_e: + STI R3; + RTS; + +#endif ENDPROC(_insw) ENTRY(_insw_8) +#ifdef CONFIG_BFIN_INS_LOWOVERHEAD P0 = R0; /* P0 = port */ cli R3; P1 = R1; /* P1 = address */ @@ -78,9 +133,29 @@ ENTRY(_insw_8) .Lword8_loop_e: NOP; sti R3; RTS; +#else + P0 = R0; /* P0 = port */ + P1 = R1; /* P1 = address */ + P2 = R2; /* P2 = count */ + SSYNC; + LSETUP( .Lword8_loop_s, .Lword8_loop_e) LC0 = P2; +.Lword8_loop_s: + CLI R3; + NOP; NOP; NOP; + R0 = W[P0]; + B[P1++] = R0; + R0 = R0 >> 8; + B[P1++] = R0; + NOP; +.Lword8_loop_e: + STI R3; + + RTS; +#endif ENDPROC(_insw_8) ENTRY(_insb) +#ifdef CONFIG_BFIN_INS_LOWOVERHEAD P0 = R0; /* P0 = port */ cli R3; P1 = R1; /* P1 = address */ @@ -93,9 +168,26 @@ ENTRY(_insb) .Lbyte_loop_e: NOP; sti R3; RTS; +#else + P0 = R0; /* P0 = port */ + P1 = R1; /* P1 = address */ + P2 = R2; /* P2 = count */ + SSYNC; + LSETUP( .Lbyte_loop_s, .Lbyte_loop_e) LC0 = P2; +.Lbyte_loop_s: + CLI R3; + NOP; NOP; NOP; + R0 = B[P0]; + B[P1++] = R0; +.Lbyte_loop_e: + STI R3; + + RTS; +#endif ENDPROC(_insb) ENTRY(_insl_16) +#ifdef CONFIG_BFIN_INS_LOWOVERHEAD P0 = R0; /* P0 = port */ cli R3; P1 = R1; /* P1 = address */ @@ -110,4 +202,21 @@ ENTRY(_insl_16) .Llong16_loop_e: NOP; sti R3; RTS; +#else + P0 = R0; /* P0 = port */ + P1 = R1; /* P1 = address */ + P2 = R2; /* P2 = count */ + SSYNC; + LSETUP( .Llong16_loop_s, .Llong16_loop_e) LC0 = P2; +.Llong16_loop_s: + CLI R3; + NOP; NOP; NOP; + R0 = [P0]; + W[P1++] = R0; + R0 = R0 >> 16; + W[P1++] = R0; +.Llong16_loop_e: + STI R3; + RTS; +#endif ENDPROC(_insl_16) -- GitLab From 130de7cebe20a74261a75bb0c6026a3199cdb980 Mon Sep 17 00:00:00 2001 From: Benjamin Matthews Date: Thu, 14 Aug 2008 14:55:54 +0800 Subject: [PATCH 328/750] Blackfin arch: add support for the BlackStamp board Signed-off-by: Benjamin Matthews Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- arch/blackfin/Kconfig | 6 +- arch/blackfin/configs/BlackStamp_defconfig | 1195 ++++++++++++++++++ arch/blackfin/mach-bf533/boards/Kconfig | 6 + arch/blackfin/mach-bf533/boards/Makefile | 1 + arch/blackfin/mach-bf533/boards/blackstamp.c | 401 ++++++ 5 files changed, 1606 insertions(+), 3 deletions(-) create mode 100644 arch/blackfin/configs/BlackStamp_defconfig create mode 100644 arch/blackfin/mach-bf533/boards/blackstamp.c diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig index ededf9319f3..f64d25973a3 100644 --- a/arch/blackfin/Kconfig +++ b/arch/blackfin/Kconfig @@ -249,7 +249,7 @@ config MEM_MT48LC8M32B2B5_7 config MEM_MT48LC32M16A2TG_75 bool - depends on (BFIN527_EZKIT || BFIN532_IP0X) + depends on (BFIN527_EZKIT || BFIN532_IP0X || BLACKSTAMP) default y source "arch/blackfin/mach-bf527/Kconfig" @@ -292,7 +292,7 @@ config CLKIN_HZ int "Frequency of the crystal on the board in Hz" default "11059200" if BFIN533_STAMP default "27000000" if BFIN533_EZKIT - default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS) + default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS || BLACKSTAMP) default "30000000" if BFIN561_EZKIT default "24576000" if PNAV10 default "10000000" if BFIN532_IP0X @@ -332,7 +332,7 @@ config VCO_MULT default "22" if BFIN533_BLUETECHNIX_CM default "20" if (BFIN537_BLUETECHNIX_CM || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM) default "20" if BFIN561_EZKIT - default "16" if H8606_HVSISTEMAS + default "16" if (H8606_HVSISTEMAS || BLACKSTAMP) help This controls the frequency of the on-chip PLL. This can be between 1 and 64. PLL Frequency = (Crystal Frequency) * (this setting) diff --git a/arch/blackfin/configs/BlackStamp_defconfig b/arch/blackfin/configs/BlackStamp_defconfig new file mode 100644 index 00000000000..2921f9952d5 --- /dev/null +++ b/arch/blackfin/configs/BlackStamp_defconfig @@ -0,0 +1,1195 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.26.2 +# +# CONFIG_MMU is not set +# CONFIG_FPU is not set +CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set +CONFIG_BLACKFIN=y +CONFIG_ZONE_DMA=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_GENERIC_GPIO=y +CONFIG_FORCE_MAX_ZONEORDER=14 +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_GROUP_SCHED is not set +CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y +# CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_UID16=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_SYSCTL_SYSCALL_CHECK=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_COMPAT_BRK=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_HAVE_KPROBES is not set +# CONFIG_HAVE_KRETPROBES is not set +# CONFIG_HAVE_DMA_ATTRS is not set +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +CONFIG_TINY_SHMEM=y +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +CONFIG_MODULE_FORCE_UNLOAD=y +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +# CONFIG_IOSCHED_DEADLINE is not set +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" +CONFIG_CLASSIC_RCU=y +# CONFIG_PREEMPT_NONE is not set +CONFIG_PREEMPT_VOLUNTARY=y +# CONFIG_PREEMPT is not set + +# +# Blackfin Processor Options +# + +# +# Processor and Board Settings +# +# CONFIG_BF522 is not set +# CONFIG_BF523 is not set +# CONFIG_BF524 is not set +# CONFIG_BF525 is not set +# CONFIG_BF526 is not set +# CONFIG_BF527 is not set +# CONFIG_BF531 is not set +CONFIG_BF532=y +# CONFIG_BF533 is not set +# CONFIG_BF534 is not set +# CONFIG_BF536 is not set +# CONFIG_BF537 is not set +# CONFIG_BF542 is not set +# CONFIG_BF544 is not set +# CONFIG_BF547 is not set +# CONFIG_BF548 is not set +# CONFIG_BF549 is not set +# CONFIG_BF561 is not set +# CONFIG_BF_REV_0_0 is not set +# CONFIG_BF_REV_0_1 is not set +# CONFIG_BF_REV_0_2 is not set +# CONFIG_BF_REV_0_3 is not set +# CONFIG_BF_REV_0_4 is not set +CONFIG_BF_REV_0_5=y +# CONFIG_BF_REV_ANY is not set +# CONFIG_BF_REV_NONE is not set +CONFIG_BF53x=y +CONFIG_MEM_MT48LC32M16A2TG_75=y +# CONFIG_BFIN533_EZKIT is not set +# CONFIG_BFIN533_STAMP is not set +# CONFIG_BFIN533_BLUETECHNIX_CM is not set +# CONFIG_H8606_HVSISTEMAS is not set +# CONFIG_BFIN532_IP0X is not set +CONFIG_BLACKSTAMP=y +# CONFIG_GENERIC_BF533_BOARD is not set + +# +# BF533/2/1 Specific Configuration +# + +# +# Interrupt Priority Assignment +# + +# +# Priority +# +CONFIG_UART_ERROR=7 +CONFIG_SPORT0_ERROR=7 +CONFIG_SPI_ERROR=7 +CONFIG_SPORT1_ERROR=7 +CONFIG_PPI_ERROR=7 +CONFIG_DMA_ERROR=7 +CONFIG_PLLWAKE_ERROR=7 +CONFIG_RTC_ERROR=8 +CONFIG_DMA0_PPI=8 +CONFIG_DMA1_SPORT0RX=9 +CONFIG_DMA2_SPORT0TX=9 +CONFIG_DMA3_SPORT1RX=9 +CONFIG_DMA4_SPORT1TX=9 +CONFIG_DMA5_SPI=10 +CONFIG_DMA6_UARTRX=10 +CONFIG_DMA7_UARTTX=10 +CONFIG_TIMER0=11 +CONFIG_TIMER1=11 +CONFIG_TIMER2=11 +CONFIG_PFA=12 +CONFIG_PFB=12 +CONFIG_MEMDMA0=13 +CONFIG_MEMDMA1=13 +CONFIG_WDTIMER=13 + +# +# Board customizations +# +# CONFIG_CMDLINE_BOOL is not set +CONFIG_BOOT_LOAD=0x1000 + +# +# Clock/PLL Setup +# +CONFIG_CLKIN_HZ=25000000 +# CONFIG_BFIN_KERNEL_CLOCK is not set +# CONFIG_PLL_BYPASS is not set +# CONFIG_CLKIN_HALF is not set +CONFIG_VCO_MULT=16 +CONFIG_CCLK_DIV_1=y +# CONFIG_CCLK_DIV_2 is not set +# CONFIG_CCLK_DIV_4 is not set +# CONFIG_CCLK_DIV_8 is not set +CONFIG_SCLK_DIV=3 +CONFIG_MAX_MEM_SIZE=64 +CONFIG_MAX_VCO_HZ=400000000 +CONFIG_MIN_VCO_HZ=50000000 +CONFIG_MAX_SCLK_HZ=133333333 +CONFIG_MIN_SCLK_HZ=27000000 + +# +# Kernel Timer/Scheduler +# +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_HZ_300 is not set +# CONFIG_HZ_1000 is not set +CONFIG_HZ=250 +# CONFIG_SCHED_HRTICK is not set +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +# CONFIG_CYCLES_CLOCKSOURCE is not set +CONFIG_TICK_ONESHOT=y +# CONFIG_NO_HZ is not set +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y + +# +# Memory Setup +# + +# +# Misc +# +CONFIG_BFIN_SCRATCH_REG_RETN=y +# CONFIG_BFIN_SCRATCH_REG_RETE is not set +# CONFIG_BFIN_SCRATCH_REG_CYCLES is not set + +# +# Blackfin Kernel Optimizations +# + +# +# Memory Optimizations +# +CONFIG_I_ENTRY_L1=y +CONFIG_EXCPT_IRQ_SYSC_L1=y +CONFIG_DO_IRQ_L1=y +CONFIG_CORE_TIMER_IRQ_L1=y +CONFIG_IDLE_L1=y +CONFIG_SCHEDULE_L1=y +CONFIG_ARITHMETIC_OPS_L1=y +CONFIG_ACCESS_OK_L1=y +CONFIG_MEMSET_L1=y +CONFIG_MEMCPY_L1=y +CONFIG_SYS_BFIN_SPINLOCK_L1=y +# CONFIG_IP_CHECKSUM_L1 is not set +CONFIG_CACHELINE_ALIGNED_L1=y +# CONFIG_SYSCALL_TAB_L1 is not set +# CONFIG_CPLB_SWITCH_TAB_L1 is not set +# CONFIG_RAMKERNEL is not set +CONFIG_ROMKERNEL=y +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_VIRT_TO_BUS=y +CONFIG_BFIN_GPTIMERS=y +CONFIG_BFIN_DMA_5XX=y +# CONFIG_DMA_UNCACHED_4M is not set +# CONFIG_DMA_UNCACHED_2M is not set +CONFIG_DMA_UNCACHED_1M=y +# CONFIG_DMA_UNCACHED_NONE is not set + +# +# Cache Support +# +CONFIG_BFIN_ICACHE=y +CONFIG_BFIN_DCACHE=y +# CONFIG_BFIN_DCACHE_BANKA is not set +# CONFIG_BFIN_ICACHE_LOCK is not set +# CONFIG_BFIN_WB is not set +CONFIG_BFIN_WT=y +# CONFIG_MPU is not set + +# +# Asynchonous Memory Configuration +# + +# +# EBIU_AMGCTL Global Control +# +CONFIG_C_AMCKEN=y +CONFIG_C_CDPRIO=y +# CONFIG_C_AMBEN is not set +# CONFIG_C_AMBEN_B0 is not set +# CONFIG_C_AMBEN_B0_B1 is not set +# CONFIG_C_AMBEN_B0_B1_B2 is not set +CONFIG_C_AMBEN_ALL=y + +# +# EBIU_AMBCTL Control +# +CONFIG_BANK_0=0x7BB0 +CONFIG_BANK_1=0x7BB0 +CONFIG_BANK_2=0x7BB0 +CONFIG_BANK_3=0xAAC2 + +# +# Bus options (PCI, PCMCIA, EISA, MCA, ISA) +# +# CONFIG_PCI is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_PCCARD is not set + +# +# Executable file formats +# +CONFIG_BINFMT_ELF_FDPIC=y +CONFIG_BINFMT_FLAT=y +CONFIG_BINFMT_ZFLAT=y +CONFIG_BINFMT_SHARED_FLAT=y +# CONFIG_BINFMT_MISC is not set + +# +# Power management options +# +CONFIG_PM=y +# CONFIG_PM_DEBUG is not set +CONFIG_PM_SLEEP=y +CONFIG_SUSPEND=y +CONFIG_SUSPEND_FREEZER=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_PM_BFIN_SLEEP_DEEPER=y +# CONFIG_PM_BFIN_SLEEP is not set +# CONFIG_PM_WAKEUP_BY_GPIO is not set + +# +# Possible Suspend Mem / Hibernate Wake-Up Sources +# + +# +# CPU Frequency scaling +# +# CONFIG_CPU_FREQ is not set + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +# CONFIG_XFRM_USER is not set +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +# CONFIG_IP_PNP_DHCP is not set +# CONFIG_IP_PNP_BOOTP is not set +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +CONFIG_SYN_COOKIES=y +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_NETLABEL is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=m +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=m +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_GEN_PROBE=m +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_CFI_INTELEXT is not set +CONFIG_MTD_CFI_AMDSTD=m +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=m +CONFIG_MTD_RAM=y +CONFIG_MTD_ROM=m +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +CONFIG_MTD_COMPLEX_MAPPINGS=y +# CONFIG_MTD_PHYSMAP is not set +# CONFIG_MTD_GPIO_ADDR is not set +# CONFIG_MTD_UCLINUX is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_DATAFLASH is not set +CONFIG_MTD_M25P80=y +# CONFIG_M25PXX_USE_FAST_READ is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +# CONFIG_MTD_NAND is not set +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +CONFIG_BLK_DEV_NBD=y +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=4096 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +CONFIG_MISC_DEVICES=y +# CONFIG_EEPROM_93CX6 is not set +# CONFIG_ENCLOSURE_SERVICES is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set +# CONFIG_SCSI_DMA is not set +# CONFIG_SCSI_NETLINK is not set +# CONFIG_ATA is not set +# CONFIG_MD is not set +CONFIG_NETDEVICES=y +# CONFIG_NETDEVICES_MULTIQUEUE is not set +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_PHYLIB is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +CONFIG_SMC91X=y +# CONFIG_SMSC911X is not set +# CONFIG_DM9000 is not set +# CONFIG_ENC28J60 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_B44 is not set +# CONFIG_NETDEV_1000 is not set +# CONFIG_NETDEV_10000 is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_JOYDEV is not set +CONFIG_INPUT_EVDEV=m +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +# CONFIG_AD9960 is not set +# CONFIG_SPI_ADC_BF533 is not set +# CONFIG_BF5xx_PPIFCD is not set +# CONFIG_BFIN_SIMPLE_TIMER is not set +CONFIG_BF5xx_PPI=y +CONFIG_BFIN_SPORT=y +# CONFIG_BFIN_TIMER_LATENCY is not set +# CONFIG_TWI_LCD is not set +CONFIG_SIMPLE_GPIO=m +# CONFIG_VT is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_BFIN=y +CONFIG_SERIAL_BFIN_CONSOLE=y +CONFIG_SERIAL_BFIN_DMA=y +# CONFIG_SERIAL_BFIN_PIO is not set +CONFIG_SERIAL_BFIN_UART0=y +# CONFIG_BFIN_UART0_CTSRTS is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_BFIN_SPORT is not set +CONFIG_UNIX98_PTYS=y +# CONFIG_LEGACY_PTYS is not set + +# +# CAN, the car bus and industrial fieldbus +# +# CONFIG_CAN4LINUX is not set +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=y +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_I2C=m +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=m +CONFIG_I2C_ALGOBIT=m + +# +# I2C Hardware Bus support +# +CONFIG_I2C_GPIO=m +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_SIMTEC is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_STUB is not set +# CONFIG_I2C_PCA_PLATFORM is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_SENSORS_AD5252 is not set +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +CONFIG_SPI=y +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +CONFIG_SPI_BFIN=y +# CONFIG_SPI_BITBANG is not set + +# +# SPI Protocol Masters +# +CONFIG_SPI_AT25=y +CONFIG_SPI_SPIDEV=m +# CONFIG_SPI_TLE62X0 is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +# CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_AD7418 is not set +# CONFIG_SENSORS_ADM1021 is not set +# CONFIG_SENSORS_ADM1025 is not set +# CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1029 is not set +# CONFIG_SENSORS_ADM1031 is not set +# CONFIG_SENSORS_ADM9240 is not set +# CONFIG_SENSORS_ADT7470 is not set +# CONFIG_SENSORS_ADT7473 is not set +# CONFIG_SENSORS_ATXP1 is not set +# CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_F75375S is not set +# CONFIG_SENSORS_GL518SM is not set +# CONFIG_SENSORS_GL520SM is not set +# CONFIG_SENSORS_IT87 is not set +# CONFIG_SENSORS_LM63 is not set +# CONFIG_SENSORS_LM70 is not set +# CONFIG_SENSORS_LM75 is not set +# CONFIG_SENSORS_LM77 is not set +# CONFIG_SENSORS_LM78 is not set +# CONFIG_SENSORS_LM80 is not set +# CONFIG_SENSORS_LM83 is not set +# CONFIG_SENSORS_LM85 is not set +# CONFIG_SENSORS_LM87 is not set +# CONFIG_SENSORS_LM90 is not set +# CONFIG_SENSORS_LM92 is not set +# CONFIG_SENSORS_LM93 is not set +# CONFIG_SENSORS_MAX1619 is not set +# CONFIG_SENSORS_MAX6650 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_PC87427 is not set +# CONFIG_SENSORS_DME1737 is not set +# CONFIG_SENSORS_SMSC47M1 is not set +# CONFIG_SENSORS_SMSC47M192 is not set +# CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_ADS7828 is not set +# CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_VT1211 is not set +# CONFIG_SENSORS_W83781D is not set +# CONFIG_SENSORS_W83791D is not set +# CONFIG_SENSORS_W83792D is not set +# CONFIG_SENSORS_W83793 is not set +# CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83L786NG is not set +# CONFIG_SENSORS_W83627HF is not set +# CONFIG_SENSORS_W83627EHF is not set +# CONFIG_HWMON_DEBUG_CHIP is not set +# CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_BFIN_WDT=y + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set +# CONFIG_HTC_PASIC3 is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# +# CONFIG_DAB is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Sound +# +# CONFIG_SOUND is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set +# CONFIG_USB_SUPPORT is not set +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +# CONFIG_MMC_UNSAFE_RESUME is not set + +# +# MMC/SD Card Drivers +# +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_BOUNCE=y +# CONFIG_SDIO_UART is not set +# CONFIG_MMC_TEST is not set + +# +# MMC/SD Host Controller Drivers +# +CONFIG_MMC_SPI=y +# CONFIG_SPI_MMC is not set +# CONFIG_MEMSTICK is not set +# CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set + +# +# SPI RTC drivers +# +# CONFIG_RTC_DRV_MAX6902 is not set +# CONFIG_RTC_DRV_R9701 is not set +# CONFIG_RTC_DRV_RS5C348 is not set + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +CONFIG_RTC_DRV_BFIN=y +# CONFIG_UIO is not set + +# +# File systems +# +# CONFIG_EXT2_FS is not set +# CONFIG_EXT3_FS is not set +# CONFIG_EXT4DEV_FS is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_DNOTIFY is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +# CONFIG_TMPFS is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_YAFFS_FS=m +CONFIG_YAFFS_YAFFS1=y +# CONFIG_YAFFS_9BYTE_TAGS is not set +# CONFIG_YAFFS_DOES_ECC is not set +CONFIG_YAFFS_YAFFS2=y +CONFIG_YAFFS_AUTO_YAFFS2=y +# CONFIG_YAFFS_DISABLE_LAZY_LOAD is not set +# CONFIG_YAFFS_DISABLE_WIDE_TNODES is not set +# CONFIG_YAFFS_ALWAYS_CHECK_CHUNK_ERASED is not set +CONFIG_YAFFS_SHORT_NAMES_IN_RAM=y +CONFIG_JFFS2_FS=y +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set +# CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_FS_XATTR is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +CONFIG_NFS_V4=y +# CONFIG_NFSD is not set +# CONFIG_ROOT_NFS is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +# CONFIG_SUNRPC_BIND34 is not set +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set +CONFIG_SMB_FS=y +# CONFIG_SMB_NLS_DEFAULT is not set +CONFIG_CIFS=y +# CONFIG_CIFS_STATS is not set +# CONFIG_CIFS_WEAK_PW_HASH is not set +# CONFIG_CIFS_XATTR is not set +# CONFIG_CIFS_DEBUG2 is not set +# CONFIG_CIFS_EXPERIMENTAL is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +CONFIG_NLS_ASCII=y +# CONFIG_NLS_ISO8859_1 is not set +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +CONFIG_NLS_UTF8=y +# CONFIG_DLM is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +CONFIG_DEBUG_FS=y +# CONFIG_HEADERS_CHECK is not set +# CONFIG_DEBUG_KERNEL is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_SAMPLES is not set +CONFIG_DEBUG_MMRS=y +CONFIG_DEBUG_HUNT_FOR_ZERO=y +CONFIG_DEBUG_BFIN_HWTRACE_ON=y +CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_OFF=y +# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_ONE is not set +# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_TWO is not set +CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION=0 +# CONFIG_DEBUG_BFIN_HWTRACE_EXPAND is not set +# CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE is not set +CONFIG_EARLY_PRINTK=y +CONFIG_CPLB_INFO=y +CONFIG_ACCESS_CHECK=y + +# +# Security options +# +# CONFIG_KEYS is not set +CONFIG_SECURITY=y +# CONFIG_SECURITY_NETWORK is not set +# CONFIG_SECURITY_CAPABILITIES is not set +CONFIG_SECURITY_DEFAULT_MMAP_MIN_ADDR=0 +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_MANAGER=y +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=y +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +# CONFIG_CRYPTO_ECB is not set +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_PCBC is not set +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_LZO is not set +CONFIG_CRYPTO_HW=y + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_GENERIC_FIND_FIRST_BIT is not set +CONFIG_CRC_CCITT=m +# CONFIG_CRC16 is not set +CONFIG_CRC_ITU_T=y +CONFIG_CRC32=y +CONFIG_CRC7=y +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y diff --git a/arch/blackfin/mach-bf533/boards/Kconfig b/arch/blackfin/mach-bf533/boards/Kconfig index 840059241fb..308c98dc5ab 100644 --- a/arch/blackfin/mach-bf533/boards/Kconfig +++ b/arch/blackfin/mach-bf533/boards/Kconfig @@ -14,6 +14,12 @@ config BFIN533_STAMP help BF533-STAMP board support. +config BLACKSTAMP + bool "BlackStamp" + help + Support for the BlackStamp board. Hardware info available at + http://blackfin.uclinux.org/gf/project/blackstamp/ + config BFIN533_BLUETECHNIX_CM bool "Bluetechnix CM-BF533" depends on (BF533) diff --git a/arch/blackfin/mach-bf533/boards/Makefile b/arch/blackfin/mach-bf533/boards/Makefile index b7a1a1d79bd..9afbe72b484 100644 --- a/arch/blackfin/mach-bf533/boards/Makefile +++ b/arch/blackfin/mach-bf533/boards/Makefile @@ -7,4 +7,5 @@ obj-$(CONFIG_BFIN533_STAMP) += stamp.o obj-$(CONFIG_BFIN532_IP0X) += ip0x.o obj-$(CONFIG_BFIN533_EZKIT) += ezkit.o obj-$(CONFIG_BFIN533_BLUETECHNIX_CM) += cm_bf533.o +obj-$(CONFIG_BLACKSTAMP) += blackstamp.o obj-$(CONFIG_H8606_HVSISTEMAS) += H8606.o diff --git a/arch/blackfin/mach-bf533/boards/blackstamp.c b/arch/blackfin/mach-bf533/boards/blackstamp.c new file mode 100644 index 00000000000..d064ded8771 --- /dev/null +++ b/arch/blackfin/mach-bf533/boards/blackstamp.c @@ -0,0 +1,401 @@ +/* + * File: arch/blackfin/mach-bf533/blackstamp.c + * Based on: arch/blackfin/mach-bf533/stamp.c + * Author: Benjamin Matthews + * Aidan Williams + * + * Created: 2008 + * Description: Board Info File for the BlackStamp + * + * Copyright 2005 National ICT Australia (NICTA) + * Copyright 2004-2008 Analog Devices Inc. + * + * Enter bugs at http://blackfin.uclinux.org/ + * + * More info about the BlackStamp at: + * http://blackfin.uclinux.org/gf/project/blackstamp/ + * + * Licensed under the GPL-2 or later. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* + * Name the Board for the /proc/cpuinfo + */ +const char bfin_board_name[] = "BlackStamp"; + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) +static struct platform_device rtc_device = { + .name = "rtc-bfin", + .id = -1, +}; +#endif + +/* + * Driver needs to know address, irq and flag pin. + */ +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) +static struct resource smc91x_resources[] = { + { + .name = "smc91x-regs", + .start = 0x20300300, + .end = 0x20300300 + 16, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_PF3, + .end = IRQ_PF3, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct platform_device smc91x_device = { + .name = "smc91x", + .id = 0, + .num_resources = ARRAY_SIZE(smc91x_resources), + .resource = smc91x_resources, +}; +#endif + +#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) +static struct mtd_partition bfin_spi_flash_partitions[] = { + { + .name = "bootloader(spi)", + .size = 0x00040000, + .offset = 0, + .mask_flags = MTD_CAP_ROM + }, { + .name = "linux kernel(spi)", + .size = 0x180000, + .offset = MTDPART_OFS_APPEND, + }, { + .name = "file system(spi)", + .size = MTDPART_SIZ_FULL, + .offset = MTDPART_OFS_APPEND, + } +}; + +static struct flash_platform_data bfin_spi_flash_data = { + .name = "m25p80", + .parts = bfin_spi_flash_partitions, + .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions), + .type = "m25p64", +}; + +/* SPI flash chip (m25p64) */ +static struct bfin5xx_spi_chip spi_flash_chip_info = { + .enable_dma = 0, /* use dma transfer with this chip*/ + .bits_per_word = 8, +}; +#endif + +#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE) +static struct bfin5xx_spi_chip spi_mmc_chip_info = { + .enable_dma = 1, + .bits_per_word = 8, +}; +#endif + +#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE) +static struct bfin5xx_spi_chip spidev_chip_info = { + .enable_dma = 0, + .bits_per_word = 8, +}; +#endif + +static struct spi_board_info bfin_spi_board_info[] __initdata = { +#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) + { + /* the modalias must be the same as spi device driver name */ + .modalias = "m25p80", /* Name of spi_driver for this device */ + .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, /* Framework bus number */ + .chip_select = 2, /* Framework chip select. */ + .platform_data = &bfin_spi_flash_data, + .controller_data = &spi_flash_chip_info, + .mode = SPI_MODE_3, + }, +#endif + +#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE) + { + .modalias = "spi_mmc_dummy", + .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 0, + .platform_data = NULL, + .controller_data = &spi_mmc_chip_info, + .mode = SPI_MODE_3, + }, + { + .modalias = "spi_mmc", + .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = CONFIG_SPI_MMC_CS_CHAN, + .platform_data = NULL, + .controller_data = &spi_mmc_chip_info, + .mode = SPI_MODE_3, + }, +#endif + +#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE) + { + .modalias = "spidev", + .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 7, + .controller_data = &spidev_chip_info, + }, +#endif +}; + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +/* SPI (0) */ +static struct resource bfin_spi0_resource[] = { + [0] = { + .start = SPI0_REGBASE, + .end = SPI0_REGBASE + 0xFF, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = CH_SPI, + .end = CH_SPI, + .flags = IORESOURCE_IRQ, + } +}; + +/* SPI controller data */ +static struct bfin5xx_spi_master bfin_spi0_info = { + .num_chipselect = 8, + .enable_dma = 1, /* master has the ability to do dma transfer */ + .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0}, +}; + +static struct platform_device bfin_spi0_device = { + .name = "bfin-spi", + .id = 0, /* Bus number */ + .num_resources = ARRAY_SIZE(bfin_spi0_resource), + .resource = bfin_spi0_resource, + .dev = { + .platform_data = &bfin_spi0_info, /* Passed to driver */ + }, +}; +#endif /* spi master and devices */ + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) +static struct resource bfin_uart_resources[] = { + { + .start = 0xFFC00400, + .end = 0xFFC004FF, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device bfin_uart_device = { + .name = "bfin-uart", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_uart_resources), + .resource = bfin_uart_resources, +}; +#endif + +#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) +static struct resource bfin_sir_resources[] = { +#ifdef CONFIG_BFIN_SIR0 + { + .start = 0xFFC00400, + .end = 0xFFC004FF, + .flags = IORESOURCE_MEM, + }, +#endif +}; + +static struct platform_device bfin_sir_device = { + .name = "bfin_sir", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_sir_resources), + .resource = bfin_sir_resources, +}; +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) +static struct platform_device bfin_sport0_uart_device = { + .name = "bfin-sport-uart", + .id = 0, +}; + +static struct platform_device bfin_sport1_uart_device = { + .name = "bfin-sport-uart", + .id = 1, +}; +#endif + +#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) +#include +#include + +static struct gpio_keys_button bfin_gpio_keys_table[] = { + {BTN_0, GPIO_PF4, 0, "gpio-keys: BTN0"}, + {BTN_1, GPIO_PF5, 0, "gpio-keys: BTN1"}, + {BTN_2, GPIO_PF6, 0, "gpio-keys: BTN2"}, +}; /* Mapped to the first three PF Test Points */ + +static struct gpio_keys_platform_data bfin_gpio_keys_data = { + .buttons = bfin_gpio_keys_table, + .nbuttons = ARRAY_SIZE(bfin_gpio_keys_table), +}; + +static struct platform_device bfin_device_gpiokeys = { + .name = "gpio-keys", + .dev = { + .platform_data = &bfin_gpio_keys_data, + }, +}; +#endif + +static struct resource bfin_gpios_resources = { + .start = 0, + .end = MAX_BLACKFIN_GPIOS - 1, + .flags = IORESOURCE_IRQ, +}; + +static struct platform_device bfin_gpios_device = { + .name = "simple-gpio", + .id = -1, + .num_resources = 1, + .resource = &bfin_gpios_resources, +}; + +#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE) +#include + +static struct i2c_gpio_platform_data i2c_gpio_data = { + .sda_pin = 8, + .scl_pin = 9, + .sda_is_open_drain = 0, + .scl_is_open_drain = 0, + .udelay = 40, +}; /* This hasn't actually been used these pins + * are (currently) free pins on the expansion connector */ + +static struct platform_device i2c_gpio_device = { + .name = "i2c-gpio", + .id = 0, + .dev = { + .platform_data = &i2c_gpio_data, + }, +}; +#endif + +#ifdef CONFIG_I2C_BOARDINFO +static struct i2c_board_info __initdata bfin_i2c_board_info[] = { +}; +#endif + +static const unsigned int cclk_vlev_datasheet[] = +{ + VRPAIR(VLEV_085, 250000000), + VRPAIR(VLEV_090, 376000000), + VRPAIR(VLEV_095, 426000000), + VRPAIR(VLEV_100, 426000000), + VRPAIR(VLEV_105, 476000000), + VRPAIR(VLEV_110, 476000000), + VRPAIR(VLEV_115, 476000000), + VRPAIR(VLEV_120, 600000000), + VRPAIR(VLEV_125, 600000000), + VRPAIR(VLEV_130, 600000000), +}; + +static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = { + .tuple_tab = cclk_vlev_datasheet, + .tabsize = ARRAY_SIZE(cclk_vlev_datasheet), + .vr_settling_time = 25 /* us */, +}; + +static struct platform_device bfin_dpmc = { + .name = "bfin dpmc", + .dev = { + .platform_data = &bfin_dmpc_vreg_data, + }, +}; + +static struct platform_device *stamp_devices[] __initdata = { + + &bfin_dpmc, + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) + &rtc_device, +#endif + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) + &smc91x_device, +#endif + + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + &bfin_spi0_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) + &bfin_uart_device, +#endif + +#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) + &bfin_sir_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) + &bfin_sport0_uart_device, + &bfin_sport1_uart_device, +#endif + +#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) + &bfin_device_gpiokeys, +#endif + +#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE) + &i2c_gpio_device, +#endif + + &bfin_gpios_device, +}; + +static int __init blackstamp_init(void) +{ + int ret; + + printk(KERN_INFO "%s(): registering device resources\n", __func__); + +#ifdef CONFIG_I2C_BOARDINFO + i2c_register_board_info(0, bfin_i2c_board_info, + ARRAY_SIZE(bfin_i2c_board_info)); +#endif + + ret = platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices)); + if (ret < 0) + return ret; + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) + /* setup BF533_STAMP CPLD to route AMS3 to Ethernet MAC */ + bfin_write_FIO_DIR(bfin_read_FIO_DIR() | PF0); + bfin_write_FIO_FLAG_S(PF0); + SSYNC(); +#endif + + spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); + return 0; +} + +arch_initcall(blackstamp_init); -- GitLab From c991dd92ab150c0b4ba531105aad5612bb0dafba Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Thu, 14 Aug 2008 14:57:26 +0800 Subject: [PATCH 329/750] Blackfin arch: use %pF when printing out the double fault address so we get symbol names Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- arch/blackfin/kernel/setup.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/blackfin/kernel/setup.c b/arch/blackfin/kernel/setup.c index eb300550e09..7a82d10b4eb 100644 --- a/arch/blackfin/kernel/setup.c +++ b/arch/blackfin/kernel/setup.c @@ -790,7 +790,7 @@ void __init setup_arch(char **cmdline_p) * don't decode the address, since you don't know if this * kernel's symbol map is the same as the crashing kernel */ - printk(KERN_INFO "Recovering from Double Fault event at %p\n", __retx); + printk(KERN_INFO "Recovering from Double Fault event at %pF\n", __retx); else if (_bfin_swrst & RESET_WDOG) printk(KERN_INFO "Recovering from Watchdog event\n"); else if (_bfin_swrst & RESET_SOFTWARE) -- GitLab From 95a86b5e51139a199d081b6b108e761966d914ef Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Thu, 14 Aug 2008 15:05:01 +0800 Subject: [PATCH 330/750] Blackfin arch: clear EMAC_SYSTAT during IRQ init rather than early head.S as we dont need it setup that early Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- arch/blackfin/mach-bf527/head.S | 9 --------- arch/blackfin/mach-bf537/head.S | 9 --------- arch/blackfin/mach-common/ints-priority.c | 5 +++++ 3 files changed, 5 insertions(+), 18 deletions(-) diff --git a/arch/blackfin/mach-bf527/head.S b/arch/blackfin/mach-bf527/head.S index 2cc46f8fa9a..fa4b18eddf6 100644 --- a/arch/blackfin/mach-bf527/head.S +++ b/arch/blackfin/mach-bf527/head.S @@ -40,15 +40,6 @@ __INIT ENTRY(_mach_early_start) -#if defined(CONFIG_BF527) - p0.h = hi(EMAC_SYSTAT); - p0.l = lo(EMAC_SYSTAT); - R0.h = 0xFFFF; /* Clear EMAC Interrupt Status bits */ - R0.l = 0xFFFF; - [P0] = R0; - SSYNC; -#endif - /* Initialise UART - when booting from u-boot, the UART is not disabled * so if we dont initalize here, our serial console gets hosed */ p0.h = hi(UART1_LCR); diff --git a/arch/blackfin/mach-bf537/head.S b/arch/blackfin/mach-bf537/head.S index c02c8ce2d96..ba81b779511 100644 --- a/arch/blackfin/mach-bf537/head.S +++ b/arch/blackfin/mach-bf537/head.S @@ -54,15 +54,6 @@ ENTRY(_mach_early_start) W[P0] = R0.L; SSYNC; -#if !defined(CONFIG_BF534) - p0.h = hi(EMAC_SYSTAT); - p0.l = lo(EMAC_SYSTAT); - R0.h = 0xFFFF; /* Clear EMAC Interrupt Status bits */ - R0.l = 0xFFFF; - [P0] = R0; - SSYNC; -#endif - /* Initialise UART - when booting from u-boot, the UART is not disabled * so if we dont initalize here, our serial console gets hosed */ p0.h = hi(BFIN_UART_LCR); diff --git a/arch/blackfin/mach-common/ints-priority.c b/arch/blackfin/mach-common/ints-priority.c index 7f9df4ee734..62f8883a5c2 100644 --- a/arch/blackfin/mach-common/ints-priority.c +++ b/arch/blackfin/mach-common/ints-priority.c @@ -983,6 +983,11 @@ int __init init_arch_irq(void) local_irq_disable(); +#if defined(CONFIG_BF527) || defined(CONFIG_BF536) || defined(CONFIG_BF537) + /* Clear EMAC Interrupt Status bits so we can demux it later */ + bfin_write_EMAC_SYSTAT(-1); +#endif + #ifdef CONFIG_BF54x # ifdef CONFIG_PINTx_REASSIGN pint[0]->assign = CONFIG_PINT0_ASSIGN; -- GitLab From 7e1e7aed0ca082b4e76567ee7ea13993b476e66a Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Thu, 14 Aug 2008 15:15:43 +0800 Subject: [PATCH 331/750] Blackfin arch: do not muck with the UART during boot -- let the serial driver worry about it Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- arch/blackfin/mach-bf527/head.S | 36 ----------------------- arch/blackfin/mach-bf533/head.S | 48 ------------------------------ arch/blackfin/mach-bf537/head.S | 50 -------------------------------- arch/blackfin/mach-bf548/head.S | 10 ------- arch/blackfin/mach-bf561/head.S | 36 ----------------------- arch/blackfin/mach-common/head.S | 3 -- 6 files changed, 183 deletions(-) diff --git a/arch/blackfin/mach-bf527/head.S b/arch/blackfin/mach-bf527/head.S index fa4b18eddf6..c3334cc5bcb 100644 --- a/arch/blackfin/mach-bf527/head.S +++ b/arch/blackfin/mach-bf527/head.S @@ -35,42 +35,6 @@ #include #endif -.extern _bf53x_relocate_l1_mem - -__INIT - -ENTRY(_mach_early_start) - /* Initialise UART - when booting from u-boot, the UART is not disabled - * so if we dont initalize here, our serial console gets hosed */ - p0.h = hi(UART1_LCR); - p0.l = lo(UART1_LCR); - r0 = 0x0(Z); - w[p0] = r0.L; /* To enable DLL writes */ - ssync; - - p0.h = hi(UART1_DLL); - p0.l = lo(UART1_DLL); - r0 = 0x0(Z); - w[p0] = r0.L; - ssync; - - p0.h = hi(UART1_DLH); - p0.l = lo(UART1_DLH); - r0 = 0x00(Z); - w[p0] = r0.L; - ssync; - - p0.h = hi(UART1_GCTL); - p0.l = lo(UART1_GCTL); - r0 = 0x0(Z); - w[p0] = r0.L; /* To enable UART clock */ - ssync; - - rts; -ENDPROC(_mach_early_start) - -__FINIT - .section .l1.text #ifdef CONFIG_BFIN_KERNEL_CLOCK ENTRY(_start_dma_code) diff --git a/arch/blackfin/mach-bf533/head.S b/arch/blackfin/mach-bf533/head.S index 184296bee3c..d59db86195b 100644 --- a/arch/blackfin/mach-bf533/head.S +++ b/arch/blackfin/mach-bf533/head.S @@ -35,54 +35,6 @@ #include #endif -.extern _bf53x_relocate_l1_mem - -__INIT - -ENTRY(_mach_early_start) - p0.h = hi(FIO_MASKA_C); - p0.l = lo(FIO_MASKA_C); - r0 = 0xFFFF(Z); - w[p0] = r0.L; /* Disable all interrupts */ - ssync; - - p0.h = hi(FIO_MASKB_C); - p0.l = lo(FIO_MASKB_C); - r0 = 0xFFFF(Z); - w[p0] = r0.L; /* Disable all interrupts */ - ssync; - - /* Initialise UART - when booting from u-boot, the UART is not disabled - * so if we dont initalize here, our serial console gets hosed */ - p0.h = hi(BFIN_UART_LCR); - p0.l = lo(BFIN_UART_LCR); - r0 = 0x0(Z); - w[p0] = r0.L; /* To enable DLL writes */ - ssync; - - p0.h = hi(BFIN_UART_DLL); - p0.l = lo(BFIN_UART_DLL); - r0 = 0x0(Z); - w[p0] = r0.L; - ssync; - - p0.h = hi(BFIN_UART_DLH); - p0.l = lo(BFIN_UART_DLH); - r0 = 0x00(Z); - w[p0] = r0.L; - ssync; - - p0.h = hi(BFIN_UART_GCTL); - p0.l = lo(BFIN_UART_GCTL); - r0 = 0x0(Z); - w[p0] = r0.L; /* To enable UART clock */ - ssync; - - rts; -ENDPROC(_mach_early_start) - -__FINIT - .section .l1.text #ifdef CONFIG_BFIN_KERNEL_CLOCK ENTRY(_start_dma_code) diff --git a/arch/blackfin/mach-bf537/head.S b/arch/blackfin/mach-bf537/head.S index ba81b779511..64e0287ab26 100644 --- a/arch/blackfin/mach-bf537/head.S +++ b/arch/blackfin/mach-bf537/head.S @@ -35,56 +35,6 @@ #include #endif -.extern _bf53x_relocate_l1_mem - -__INIT - -ENTRY(_mach_early_start) - /* Initialise General-Purpose I/O Modules on BF537 */ - p0.h = hi(BFIN_PORT_MUX); - p0.l = lo(BFIN_PORT_MUX); - R0 = (PGDE_UART | PFTE_UART)(Z); - W[P0] = R0.L; /* Enable both UARTS */ - SSYNC; - - /* Enable peripheral function of PORTF for UART0 and UART1 */ - p0.h = hi(PORTF_FER); - p0.l = lo(PORTF_FER); - R0 = 0x000F(Z); - W[P0] = R0.L; - SSYNC; - - /* Initialise UART - when booting from u-boot, the UART is not disabled - * so if we dont initalize here, our serial console gets hosed */ - p0.h = hi(BFIN_UART_LCR); - p0.l = lo(BFIN_UART_LCR); - r0 = 0x0(Z); - w[p0] = r0.L; /* To enable DLL writes */ - ssync; - - p0.h = hi(BFIN_UART_DLL); - p0.l = lo(BFIN_UART_DLL); - r0 = 0x0(Z); - w[p0] = r0.L; - ssync; - - p0.h = hi(BFIN_UART_DLH); - p0.l = lo(BFIN_UART_DLH); - r0 = 0x00(Z); - w[p0] = r0.L; - ssync; - - p0.h = hi(BFIN_UART_GCTL); - p0.l = lo(BFIN_UART_GCTL); - r0 = 0x0(Z); - w[p0] = r0.L; /* To enable UART clock */ - ssync; - - rts; -ENDPROC(_mach_early_start) - -__FINIT - .section .l1.text #ifdef CONFIG_BFIN_KERNEL_CLOCK ENTRY(_start_dma_code) diff --git a/arch/blackfin/mach-bf548/head.S b/arch/blackfin/mach-bf548/head.S index 0b18196df86..e3000f70a26 100644 --- a/arch/blackfin/mach-bf548/head.S +++ b/arch/blackfin/mach-bf548/head.S @@ -35,16 +35,6 @@ #include #endif -.extern _bf53x_relocate_l1_mem - -__INIT - -ENTRY(_mach_early_start) - rts; -ENDPROC(_mach_early_start) - -__FINIT - .section .l1.text #ifdef CONFIG_BFIN_KERNEL_CLOCK ENTRY(_start_dma_code) diff --git a/arch/blackfin/mach-bf561/head.S b/arch/blackfin/mach-bf561/head.S index fe6f979947c..c7a81e34703 100644 --- a/arch/blackfin/mach-bf561/head.S +++ b/arch/blackfin/mach-bf561/head.S @@ -35,42 +35,6 @@ #include #endif -.extern _bf53x_relocate_l1_mem - -__INIT - -ENTRY(_mach_early_start) - /* Initialise UART - when booting from u-boot, the UART is not disabled - * so if we dont initalize here, our serial console gets hosed */ - p0.h = hi(BFIN_UART_LCR); - p0.l = lo(BFIN_UART_LCR); - r0 = 0x0(Z); - w[p0] = r0.L; /* To enable DLL writes */ - ssync; - - p0.h = hi(BFIN_UART_DLL); - p0.l = lo(BFIN_UART_DLL); - r0 = 0x0(Z); - w[p0] = r0.L; - ssync; - - p0.h = hi(BFIN_UART_DLH); - p0.l = lo(BFIN_UART_DLH); - r0 = 0x00(Z); - w[p0] = r0.L; - ssync; - - p0.h = hi(BFIN_UART_GCTL); - p0.l = lo(BFIN_UART_GCTL); - r0 = 0x0(Z); - w[p0] = r0.L; /* To enable UART clock */ - ssync; - - rts; -ENDPROC(_mach_early_start) - -__FINIT - .section .l1.text #ifdef CONFIG_BFIN_KERNEL_CLOCK ENTRY(_start_dma_code) diff --git a/arch/blackfin/mach-common/head.S b/arch/blackfin/mach-common/head.S index fb7e2d42699..191b4e974c4 100644 --- a/arch/blackfin/mach-common/head.S +++ b/arch/blackfin/mach-common/head.S @@ -96,9 +96,6 @@ ENTRY(__start) R0 = RETX; [P0] = R0; - /* Let each Blackfin family do its own thing */ - call _mach_early_start; - /* Initialize stack pointer */ sp.l = lo(INITIAL_STACK); sp.h = hi(INITIAL_STACK); -- GitLab From b42a9f442c6f9f47a9d63f66fcc67ab8efe7b7fa Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Thu, 14 Aug 2008 15:19:25 +0800 Subject: [PATCH 332/750] Blackfin arch: fix missing digit in SCLK range checking Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu --- include/asm-blackfin/mach-bf533/mem_init.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/asm-blackfin/mach-bf533/mem_init.h b/include/asm-blackfin/mach-bf533/mem_init.h index 995c06b2b1e..ed2034bf10e 100644 --- a/include/asm-blackfin/mach-bf533/mem_init.h +++ b/include/asm-blackfin/mach-bf533/mem_init.h @@ -47,7 +47,7 @@ #define SDRAM_tRCD TRCD_2 #define SDRAM_tWR TWR_2 #endif -#if (CONFIG_SCLK_HZ > 8955223) && (CONFIG_SCLK_HZ <= 104477612) +#if (CONFIG_SCLK_HZ > 89552239) && (CONFIG_SCLK_HZ <= 104477612) #define SDRAM_tRP TRP_2 #define SDRAM_tRP_num 2 #define SDRAM_tRAS TRAS_5 -- GitLab From a4b7b6d7d3f4f71e741a878bcca6226d8d326a34 Mon Sep 17 00:00:00 2001 From: Bryan Wu Date: Thu, 14 Aug 2008 15:40:19 +0800 Subject: [PATCH 333/750] Blackfin arch: hook up some missing new system calls Signed-off-by: Bryan Wu --- arch/blackfin/mach-common/entry.S | 6 ++++++ include/asm-blackfin/unistd.h | 8 +++++++- 2 files changed, 13 insertions(+), 1 deletion(-) diff --git a/arch/blackfin/mach-common/entry.S b/arch/blackfin/mach-common/entry.S index 4bd971e81f1..117c01c2c6b 100644 --- a/arch/blackfin/mach-common/entry.S +++ b/arch/blackfin/mach-common/entry.S @@ -1422,6 +1422,12 @@ ENTRY(_sys_call_table) .long _sys_semtimedop .long _sys_timerfd_settime .long _sys_timerfd_gettime + .long _sys_signalfd4 /* 360 */ + .long _sys_eventfd2 + .long _sys_epoll_create1 + .long _sys_dup3 + .long _sys_pipe2 + .long _sys_inotify_init1 /* 365 */ .rept NR_syscalls-(.-_sys_call_table)/4 .long _sys_ni_syscall diff --git a/include/asm-blackfin/unistd.h b/include/asm-blackfin/unistd.h index 42955d0c439..1e57b636e0b 100644 --- a/include/asm-blackfin/unistd.h +++ b/include/asm-blackfin/unistd.h @@ -372,8 +372,14 @@ #define __NR_semtimedop 357 #define __NR_timerfd_settime 358 #define __NR_timerfd_gettime 359 +#define __NR_signalfd4 360 +#define __NR_eventfd2 361 +#define __NR_epoll_create1 362 +#define __NR_dup3 363 +#define __NR_pipe2 364 +#define __NR_inotify_init1 365 -#define __NR_syscall 360 +#define __NR_syscall 366 #define NR_syscalls __NR_syscall /* Old optional stuff no one actually uses */ -- GitLab From fde9403a982218fa8a437f815e7aa0e583e2d6ed Mon Sep 17 00:00:00 2001 From: Huang Weiyi Date: Mon, 11 Aug 2008 12:56:44 +0800 Subject: [PATCH 334/750] [netdrvr] remove unnecessary #include The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION. drivers/net/acenic.c drivers/net/bnx2x_link.c drivers/net/bnx2x_main.c drivers/net/cpmac.c drivers/net/gianfar_sysfs.c drivers/net/ipg.h drivers/net/ppp_mppe.c drivers/net/pppol2tp.c drivers/net/r6040.c drivers/net/sh_eth.c drivers/net/sky2.c drivers/net/tehuti.h drivers/net/typhoon.c This patch removes the said #include . Signed-off-by: Huang Weiyi Signed-off-by: Jeff Garzik --- drivers/net/acenic.c | 1 - drivers/net/bnx2x_link.c | 1 - drivers/net/bnx2x_main.c | 1 - drivers/net/cpmac.c | 1 - drivers/net/gianfar_sysfs.c | 1 - drivers/net/ipg.h | 2 -- drivers/net/ppp_mppe.c | 1 - drivers/net/pppol2tp.c | 1 - drivers/net/r6040.c | 1 - drivers/net/sh_eth.c | 1 - drivers/net/sky2.c | 1 - drivers/net/tehuti.h | 1 - drivers/net/typhoon.c | 1 - 13 files changed, 14 deletions(-) diff --git a/drivers/net/acenic.c b/drivers/net/acenic.c index e4483de84e7..66de80b64b9 100644 --- a/drivers/net/acenic.c +++ b/drivers/net/acenic.c @@ -52,7 +52,6 @@ #include #include -#include #include #include #include diff --git a/drivers/net/bnx2x_link.c b/drivers/net/bnx2x_link.c index 8b92c6ad075..4ce7fe9c525 100644 --- a/drivers/net/bnx2x_link.c +++ b/drivers/net/bnx2x_link.c @@ -21,7 +21,6 @@ #include #include #include -#include #include "bnx2x_reg.h" #include "bnx2x_fw_defs.h" diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c index 3e7dc171cdf..971576b4368 100644 --- a/drivers/net/bnx2x_main.c +++ b/drivers/net/bnx2x_main.c @@ -44,7 +44,6 @@ #include #include #include -#include #include #include #include diff --git a/drivers/net/cpmac.c b/drivers/net/cpmac.c index a7800e55909..ec6b0af3d46 100644 --- a/drivers/net/cpmac.c +++ b/drivers/net/cpmac.c @@ -26,7 +26,6 @@ #include #include #include -#include #include #include diff --git a/drivers/net/gianfar_sysfs.c b/drivers/net/gianfar_sysfs.c index 5116f68e01b..782c2017008 100644 --- a/drivers/net/gianfar_sysfs.c +++ b/drivers/net/gianfar_sysfs.c @@ -33,7 +33,6 @@ #include #include -#include #include "gianfar.h" diff --git a/drivers/net/ipg.h b/drivers/net/ipg.h index e0e718ab4c2..dd9318f1949 100644 --- a/drivers/net/ipg.h +++ b/drivers/net/ipg.h @@ -7,7 +7,6 @@ #ifndef __LINUX_IPG_H #define __LINUX_IPG_H -#include #include #include @@ -21,7 +20,6 @@ #include #include #include -#include #include /* diff --git a/drivers/net/ppp_mppe.c b/drivers/net/ppp_mppe.c index b35d7944950..88f03c9e940 100644 --- a/drivers/net/ppp_mppe.c +++ b/drivers/net/ppp_mppe.c @@ -46,7 +46,6 @@ #include #include #include -#include #include #include #include diff --git a/drivers/net/pppol2tp.c b/drivers/net/pppol2tp.c index f9298827a76..ff175e8f36b 100644 --- a/drivers/net/pppol2tp.c +++ b/drivers/net/pppol2tp.c @@ -61,7 +61,6 @@ */ #include -#include #include #include #include diff --git a/drivers/net/r6040.c b/drivers/net/r6040.c index 6531ff565c5..5d86281d936 100644 --- a/drivers/net/r6040.c +++ b/drivers/net/r6040.c @@ -24,7 +24,6 @@ #include #include -#include #include #include #include diff --git a/drivers/net/sh_eth.c b/drivers/net/sh_eth.c index 25e62cf58d3..1c370e6aa64 100644 --- a/drivers/net/sh_eth.c +++ b/drivers/net/sh_eth.c @@ -20,7 +20,6 @@ * the file called "COPYING". */ -#include #include #include #include diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index 7d29edcd40b..06dfc950f33 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -24,7 +24,6 @@ #include #include -#include #include #include #include diff --git a/drivers/net/tehuti.h b/drivers/net/tehuti.h index c66dfc9ec1e..7db48f1cd94 100644 --- a/drivers/net/tehuti.h +++ b/drivers/net/tehuti.h @@ -27,7 +27,6 @@ #include #include #include -#include #include #include #include diff --git a/drivers/net/typhoon.c b/drivers/net/typhoon.c index 8549f1159a3..734ce0977f0 100644 --- a/drivers/net/typhoon.c +++ b/drivers/net/typhoon.c @@ -128,7 +128,6 @@ static const int multicast_filter_limit = 32; #include #include #include -#include #include #include "typhoon.h" -- GitLab From 2a54adc3ad771c997bfa721f098d2d4a6ef6ea38 Mon Sep 17 00:00:00 2001 From: Scott Wood Date: Tue, 12 Aug 2008 15:10:46 -0500 Subject: [PATCH 335/750] gianfar: Call gfar_halt_nodisable() from gfar_halt(). gfar_halt() was factored out into halting and disabling by commit d87eb12785c14de1586e3bad86ca2c0991300339, as the suspend() method only wants to do the former. However, the call to gfar_halt_nodisable() from gfar_halt() apparently got lost during the patch respin process. This adds it back. Signed-off-by: Scott Wood Signed-off-by: Jeff Garzik --- drivers/net/gianfar.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) diff --git a/drivers/net/gianfar.c b/drivers/net/gianfar.c index ca6cf6ecb37..999d6916827 100644 --- a/drivers/net/gianfar.c +++ b/drivers/net/gianfar.c @@ -134,9 +134,7 @@ static int gfar_process_frame(struct net_device *dev, struct sk_buff *skb, int l static void gfar_vlan_rx_register(struct net_device *netdev, struct vlan_group *grp); void gfar_halt(struct net_device *dev); -#ifdef CONFIG_PM static void gfar_halt_nodisable(struct net_device *dev); -#endif void gfar_start(struct net_device *dev); static void gfar_clear_exact_match(struct net_device *dev); static void gfar_set_mac_for_addr(struct net_device *dev, int num, u8 *addr); @@ -631,7 +629,6 @@ static void init_registers(struct net_device *dev) } -#ifdef CONFIG_PM /* Halt the receive and transmit queues */ static void gfar_halt_nodisable(struct net_device *dev) { @@ -657,7 +654,6 @@ static void gfar_halt_nodisable(struct net_device *dev) cpu_relax(); } } -#endif /* Halt the receive and transmit queues */ void gfar_halt(struct net_device *dev) @@ -666,6 +662,8 @@ void gfar_halt(struct net_device *dev) struct gfar __iomem *regs = priv->regs; u32 tempval; + gfar_halt_nodisable(dev); + /* Disable Rx and Tx */ tempval = gfar_read(®s->maccfg1); tempval &= ~(MACCFG1_RX_EN | MACCFG1_TX_EN); -- GitLab From 7144decb0f482fcb2152c10c376f0574d563ca52 Mon Sep 17 00:00:00 2001 From: Mikael Pettersson Date: Wed, 13 Aug 2008 21:08:14 +0200 Subject: [PATCH 336/750] ixp4xx_eth: fix dma_mapping_error() compile errors The arm ixp4xx_eth driver doesn't compile in 2.6.27-rc1: CC [M] drivers/net/arm/ixp4xx_eth.o drivers/net/arm/ixp4xx_eth.c: In function 'eth_poll': drivers/net/arm/ixp4xx_eth.c:554: warning: passing argument 1 of 'dma_mapping_error' makes pointer from integer without a cast drivers/net/arm/ixp4xx_eth.c:554: error: too few arguments to function 'dma_mapping_error' drivers/net/arm/ixp4xx_eth.c: In function 'eth_xmit': drivers/net/arm/ixp4xx_eth.c:701: warning: passing argument 1 of 'dma_mapping_error' makes pointer from integer without a cast drivers/net/arm/ixp4xx_eth.c:701: error: too few arguments to function 'dma_mapping_error' drivers/net/arm/ixp4xx_eth.c: In function 'init_queues': drivers/net/arm/ixp4xx_eth.c:886: warning: passing argument 1 of 'dma_mapping_error' makes pointer from integer without a cast drivers/net/arm/ixp4xx_eth.c:886: error: too few arguments to function 'dma_mapping_error' make[3]: *** [drivers/net/arm/ixp4xx_eth.o] Error 1 make[2]: *** [drivers/net/arm] Error 2 make[1]: *** [drivers/net] Error 2 make: *** [drivers] Error 2 dma_mapping_error() changed in 2.6.27-rc1 to also take a device parameter, but nobody bothered updating ixp4xx_eth.c. Fixed by passing the appropriate device value in the dma_mapping_error() calls. Tested on an ixp425 box. Signed-off-by: Mikael Pettersson Acked-by: Krzysztof Halasa Signed-off-by: Jeff Garzik --- drivers/net/arm/ixp4xx_eth.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/net/arm/ixp4xx_eth.c b/drivers/net/arm/ixp4xx_eth.c index 9b777d9433c..7d5db2ece1b 100644 --- a/drivers/net/arm/ixp4xx_eth.c +++ b/drivers/net/arm/ixp4xx_eth.c @@ -551,7 +551,7 @@ static int eth_poll(struct napi_struct *napi, int budget) if ((skb = netdev_alloc_skb(dev, RX_BUFF_SIZE))) { phys = dma_map_single(&dev->dev, skb->data, RX_BUFF_SIZE, DMA_FROM_DEVICE); - if (dma_mapping_error(phys)) { + if (dma_mapping_error(&dev->dev, phys)) { dev_kfree_skb(skb); skb = NULL; } @@ -698,7 +698,7 @@ static int eth_xmit(struct sk_buff *skb, struct net_device *dev) #endif phys = dma_map_single(&dev->dev, mem, bytes, DMA_TO_DEVICE); - if (dma_mapping_error(phys)) { + if (dma_mapping_error(&dev->dev, phys)) { #ifdef __ARMEB__ dev_kfree_skb(skb); #else @@ -883,7 +883,7 @@ static int init_queues(struct port *port) desc->buf_len = MAX_MRU; desc->data = dma_map_single(&port->netdev->dev, data, RX_BUFF_SIZE, DMA_FROM_DEVICE); - if (dma_mapping_error(desc->data)) { + if (dma_mapping_error(&port->netdev->dev, desc->data)) { free_buffer(buff); return -EIO; } -- GitLab From 13b2738cbb4b59f695bd72bcaabd71317e7731d2 Mon Sep 17 00:00:00 2001 From: Brice Goglin Date: Wed, 13 Aug 2008 21:05:52 +0200 Subject: [PATCH 337/750] myri10ge: myri10ge_fw_name also overrides the rss firmware When myri10ge_fw_name is given, use it to override the rss firmware name as well. Signed-off-by: Brice Goglin Signed-off-by: Jeff Garzik --- drivers/net/myri10ge/myri10ge.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/drivers/net/myri10ge/myri10ge.c b/drivers/net/myri10ge/myri10ge.c index f1de38f8b74..5d76cd09e24 100644 --- a/drivers/net/myri10ge/myri10ge.c +++ b/drivers/net/myri10ge/myri10ge.c @@ -3548,7 +3548,11 @@ static void myri10ge_probe_slices(struct myri10ge_priv *mgp) /* try to load the slice aware rss firmware */ old_fw = mgp->fw_name; - if (old_fw == myri10ge_fw_aligned) + if (myri10ge_fw_name != NULL) { + dev_info(&mgp->pdev->dev, "overriding rss firmware to %s\n", + myri10ge_fw_name); + mgp->fw_name = myri10ge_fw_name; + } else if (old_fw == myri10ge_fw_aligned) mgp->fw_name = myri10ge_fw_rss_aligned; else mgp->fw_name = myri10ge_fw_rss_unaligned; -- GitLab From 2726fcf0dab1a9b1fd04dea3837b2b0bb639c1bd Mon Sep 17 00:00:00 2001 From: Vegard Nossum Date: Wed, 6 Aug 2008 14:12:11 +0200 Subject: [PATCH 338/750] au1000_eth: use 'unsigned long' for irqflags The patch was generated using the Coccinelle semantic patch framework. Cc: Julia Lawall Cc: Alexey Dobriyan Cc: Jeff Garzik Signed-off-by: Vegard Nossum Signed-off-by: Jeff Garzik --- drivers/net/au1000_eth.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/au1000_eth.c b/drivers/net/au1000_eth.c index cb8be490e5a..5ee1b0557a0 100644 --- a/drivers/net/au1000_eth.c +++ b/drivers/net/au1000_eth.c @@ -807,7 +807,7 @@ err_out: static int au1000_init(struct net_device *dev) { struct au1000_private *aup = (struct au1000_private *) dev->priv; - u32 flags; + unsigned long flags; int i; u32 control; -- GitLab From e484d5f5c8c64e2c4f110c59e9e964884107822a Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Sun, 10 Aug 2008 19:30:28 +0200 Subject: [PATCH 339/750] sky2: Fix suspend/hibernation/shutdown regression with WOL enabled (rev. 2) On my test box with the Asus M3A32-MVP main board there is a regression from 2.6.26 related to suspend, hibernation and shutdown. Namely, if Wake-on-LAN is enabled with 'ethtool -s eth0 wol g', the box hangs solid during all of these operations, while executing either sky2_suspend(), or sky2_shutdown(). This patch fixes it for me. Signed-off-by: Rafael J. Wysocki Signed-off-by: Jeff Garzik --- drivers/net/sky2.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index 06dfc950f33..e24b25ca1c6 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -665,11 +665,16 @@ static void sky2_phy_power_down(struct sky2_hw *hw, unsigned port) if (hw->chip_id != CHIP_ID_YUKON_EC) { if (hw->chip_id == CHIP_ID_YUKON_EC_U) { - ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); + /* select page 2 to access MAC control register */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2); + ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); /* enable Power Down */ ctrl |= PHY_M_PC_POW_D_ENA; gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); + + /* set page register back to 0 */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0); } /* set IEEE compatible Power Down Mode (dev. #4.99) */ -- GitLab From 0d63bea2c20651588e5e631799a961468a735eb9 Mon Sep 17 00:00:00 2001 From: Robert Fitzsimons Date: Sat, 9 Aug 2008 17:54:02 +0100 Subject: [PATCH 340/750] tlan: Fix two regressions introduced by 64bit conversion. Two regressions were introduced by the recent tlan: 64bit conversion commit (93e16847c9db0093065c98063cfc639cdfccf19a). The first in TLan_GetSKB caused a NULL pointer dereference. With the second causing the link to fail to come up. Signed-off-by: Robert Fitzsimons Signed-off-by: Jeff Garzik --- drivers/net/tlan.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/net/tlan.c b/drivers/net/tlan.c index 85246ed7cb9..ec871f64676 100644 --- a/drivers/net/tlan.c +++ b/drivers/net/tlan.c @@ -360,8 +360,8 @@ TLan_GetSKB( const struct tlan_list_tag *tag) { unsigned long addr; - addr = tag->buffer[8].address; - addr |= (tag->buffer[9].address << 16) << 16; + addr = tag->buffer[9].address; + addr |= (tag->buffer[8].address << 16) << 16; return (struct sk_buff *) addr; } @@ -1984,7 +1984,6 @@ static void TLan_ResetLists( struct net_device *dev ) TLanList *list; dma_addr_t list_phys; struct sk_buff *skb; - void *t = NULL; priv->txHead = 0; priv->txTail = 0; @@ -2022,7 +2021,8 @@ static void TLan_ResetLists( struct net_device *dev ) } skb_reserve( skb, NET_IP_ALIGN ); - list->buffer[0].address = pci_map_single(priv->pciDev, t, + list->buffer[0].address = pci_map_single(priv->pciDev, + skb->data, TLAN_MAX_FRAME_SIZE, PCI_DMA_FROMDEVICE); TLan_StoreSKB(list, skb); -- GitLab From 56e1f82968af79f70902008098a4687198142ce7 Mon Sep 17 00:00:00 2001 From: Bruce Allan Date: Fri, 8 Aug 2008 18:35:44 -0700 Subject: [PATCH 341/750] e1000e: Return 1 instead of a non-zero value for link up indication A number of users have mentioned they have tools that rely on a link-up indication having a return value of 1 rather than a non-zero value. Signed-off-by: Bruce Allan Signed-off-by: Jeff Kirsher Signed-off-by: Jeff Garzik --- drivers/net/e1000e/ethtool.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/e1000e/ethtool.c b/drivers/net/e1000e/ethtool.c index cf9679f2b7c..e21c9e0f373 100644 --- a/drivers/net/e1000e/ethtool.c +++ b/drivers/net/e1000e/ethtool.c @@ -177,7 +177,7 @@ static u32 e1000_get_link(struct net_device *netdev) u32 status; status = er32(STATUS); - return (status & E1000_STATUS_LU); + return (status & E1000_STATUS_LU) ? 1 : 0; } static int e1000_set_spd_dplx(struct e1000_adapter *adapter, u16 spddplx) -- GitLab From 2d06cad1a5ceb3b04dc9547e261ad4fcebf7433d Mon Sep 17 00:00:00 2001 From: Bruce Allan Date: Fri, 8 Aug 2008 18:35:51 -0700 Subject: [PATCH 342/750] e1000e: Set InterruptThrottleRate to default when invalid value used During module load, seting the InterruptThrottleRate parameter to an invalid value would result in the itr/itr_setting pair being set to unexpected values which would result in poor performance. Signed-off-by: Bruce Allan Signed-off-by: Jeff Kirsher Signed-off-by: Jeff Garzik --- drivers/net/e1000e/param.c | 23 +++++++++++++++++++---- 1 file changed, 19 insertions(+), 4 deletions(-) diff --git a/drivers/net/e1000e/param.c b/drivers/net/e1000e/param.c index 8effc3107f9..b0499f27e5f 100644 --- a/drivers/net/e1000e/param.c +++ b/drivers/net/e1000e/param.c @@ -327,11 +327,26 @@ void __devinit e1000e_check_options(struct e1000_adapter *adapter) e1000_validate_option(&adapter->itr, &opt, adapter); /* - * save the setting, because the dynamic bits - * change itr. clear the lower two bits - * because they are used as control + * Save the setting, because the dynamic bits + * change itr. */ - adapter->itr_setting = adapter->itr & ~3; + if (e1000_validate_option(&adapter->itr, &opt, + adapter) && + (adapter->itr == 3)) { + /* + * In case of invalid user value, + * default to conservative mode. + */ + adapter->itr_setting = adapter->itr; + adapter->itr = 20000; + } else { + /* + * Clear the lower two bits because + * they are used as control. + */ + adapter->itr_setting = + adapter->itr & ~3; + } break; } } else { -- GitLab From 808ff676c46d8e259c2cb38579f94f8e6ae38009 Mon Sep 17 00:00:00 2001 From: Bruce Allan Date: Fri, 8 Aug 2008 18:35:56 -0700 Subject: [PATCH 343/750] e1000e: Use skb_copy_to_linear_data_offset introduced in 2.6.22 The e1000e driver was based on a version of e1000 prior to acme's introduction of skb_copy_to_linear_data_offset, and was submitted after acme went through and coverted all the drivers to use it. Signed-off-by: Bruce Allan Signed-off-by: Jeff Kirsher Signed-off-by: Jeff Garzik --- drivers/net/e1000e/netdev.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c index 05b0b2f9c54..efa944509a3 100644 --- a/drivers/net/e1000e/netdev.c +++ b/drivers/net/e1000e/netdev.c @@ -510,9 +510,12 @@ static bool e1000_clean_rx_irq(struct e1000_adapter *adapter, netdev_alloc_skb(netdev, length + NET_IP_ALIGN); if (new_skb) { skb_reserve(new_skb, NET_IP_ALIGN); - memcpy(new_skb->data - NET_IP_ALIGN, - skb->data - NET_IP_ALIGN, - length + NET_IP_ALIGN); + skb_copy_to_linear_data_offset(new_skb, + -NET_IP_ALIGN, + (skb->data - + NET_IP_ALIGN), + (length + + NET_IP_ALIGN)); /* save the skb in buffer_info as good */ buffer_info->skb = skb; skb = new_skb; -- GitLab From 10f1b492135620a87970cad9f80439249dcce299 Mon Sep 17 00:00:00 2001 From: Bruce Allan Date: Fri, 8 Aug 2008 18:36:01 -0700 Subject: [PATCH 344/750] e1000e: Increase Tx timeout factor for 10Mbps Prevent Tx hangs from happening on 10Mb flood ping by increasing the timeout factor. Signed-off-by: Bruce Allan Signed-off-by: Jeff Kirsher Signed-off-by: Jeff Garzik --- drivers/net/e1000e/netdev.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c index efa944509a3..4573c7b9cbd 100644 --- a/drivers/net/e1000e/netdev.c +++ b/drivers/net/e1000e/netdev.c @@ -3058,7 +3058,7 @@ static void e1000_watchdog_task(struct work_struct *work) case SPEED_10: txb2b = 0; netdev->tx_queue_len = 10; - adapter->tx_timeout_factor = 14; + adapter->tx_timeout_factor = 16; break; case SPEED_100: txb2b = 0; -- GitLab From d53f706da808e6d93dc60b1910233a309009939f Mon Sep 17 00:00:00 2001 From: Bruce Allan Date: Fri, 8 Aug 2008 18:36:06 -0700 Subject: [PATCH 345/750] e1000e: increase minimum frame size allowed Setting an MTU value below 68 was disabling the network connection and would not reconnect until the driver was reloaded. Prevent changing the MTU to anything below 68. Signed-off-by: Bruce Allan Signed-off-by: Jeff Kirsher Signed-off-by: Jeff Garzik --- drivers/net/e1000e/netdev.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c index 4573c7b9cbd..b8b26cf78de 100644 --- a/drivers/net/e1000e/netdev.c +++ b/drivers/net/e1000e/netdev.c @@ -3724,7 +3724,7 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu) struct e1000_adapter *adapter = netdev_priv(netdev); int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN; - if ((max_frame < ETH_ZLEN + ETH_FCS_LEN) || + if ((new_mtu < ETH_ZLEN + ETH_FCS_LEN + VLAN_HLEN) || (max_frame > MAX_JUMBO_FRAME_SIZE)) { e_err("Invalid MTU setting\n"); return -EINVAL; -- GitLab From c918dcce92f76bb9903e4d049f4780bad384c207 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Thu, 14 Aug 2008 01:41:39 -0700 Subject: [PATCH 346/750] sparc64: Fix overshoot in nid_range(). If 'start' does not begin on a page boundary, we can overshoot past 'end'. Signed-off-by: David S. Miller --- arch/sparc64/mm/init.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/sparc64/mm/init.c b/arch/sparc64/mm/init.c index 217de3ea29e..64d8e7623e0 100644 --- a/arch/sparc64/mm/init.c +++ b/arch/sparc64/mm/init.c @@ -796,6 +796,9 @@ static unsigned long nid_range(unsigned long start, unsigned long end, start += PAGE_SIZE; } + if (start > end) + start = end; + return start; } #else -- GitLab From f8d59f7826aa73c5e7682fbed6db38020635d466 Mon Sep 17 00:00:00 2001 From: Bruce Allan Date: Fri, 8 Aug 2008 18:36:11 -0700 Subject: [PATCH 347/750] e1000e: test for unusable MSI support Some systems do not like 82571/2 use of 16-bit MSI messages and some other systems claim to support MSI, but neither really works. Setup a test MSI handler to detect whether or not MSI is working properly, and if not, fallback to legacy INTx interrupts. Signed-off-by: Bruce Allan Signed-off-by: Jeff Kirsher Signed-off-by: Jeff Garzik --- drivers/net/e1000e/defines.h | 2 +- drivers/net/e1000e/e1000.h | 1 + drivers/net/e1000e/netdev.c | 172 +++++++++++++++++++++++++++++++++-- 3 files changed, 164 insertions(+), 11 deletions(-) diff --git a/drivers/net/e1000e/defines.h b/drivers/net/e1000e/defines.h index f823b8ba578..14b0e6cd3b8 100644 --- a/drivers/net/e1000e/defines.h +++ b/drivers/net/e1000e/defines.h @@ -389,7 +389,7 @@ /* Interrupt Cause Set */ #define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */ -#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */ +#define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* Rx sequence error */ #define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* Rx desc min. threshold */ /* Transmit Descriptor Control */ diff --git a/drivers/net/e1000e/e1000.h b/drivers/net/e1000e/e1000.h index cf57050d99d..ac4e506b4f8 100644 --- a/drivers/net/e1000e/e1000.h +++ b/drivers/net/e1000e/e1000.h @@ -326,6 +326,7 @@ struct e1000_info { #define FLAG_RX_CSUM_ENABLED (1 << 28) #define FLAG_TSO_FORCE (1 << 29) #define FLAG_RX_RESTART_NOW (1 << 30) +#define FLAG_MSI_TEST_FAILED (1 << 31) #define E1000_RX_DESC_PS(R, i) \ (&(((union e1000_rx_desc_packet_split *)((R).desc))[i])) diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c index b8b26cf78de..d266510c8a9 100644 --- a/drivers/net/e1000e/netdev.c +++ b/drivers/net/e1000e/netdev.c @@ -1236,26 +1236,36 @@ static irqreturn_t e1000_intr(int irq, void *data) return IRQ_HANDLED; } +/** + * e1000_request_irq - initialize interrupts + * + * Attempts to configure interrupts using the best available + * capabilities of the hardware and kernel. + **/ static int e1000_request_irq(struct e1000_adapter *adapter) { struct net_device *netdev = adapter->netdev; - irq_handler_t handler = e1000_intr; int irq_flags = IRQF_SHARED; int err; - if (!pci_enable_msi(adapter->pdev)) { - adapter->flags |= FLAG_MSI_ENABLED; - handler = e1000_intr_msi; - irq_flags = 0; + if (!(adapter->flags & FLAG_MSI_TEST_FAILED)) { + err = pci_enable_msi(adapter->pdev); + if (!err) { + adapter->flags |= FLAG_MSI_ENABLED; + irq_flags = 0; + } } - err = request_irq(adapter->pdev->irq, handler, irq_flags, netdev->name, - netdev); + err = request_irq(adapter->pdev->irq, + ((adapter->flags & FLAG_MSI_ENABLED) ? + &e1000_intr_msi : &e1000_intr), + irq_flags, netdev->name, netdev); if (err) { - e_err("Unable to allocate %s interrupt (return: %d)\n", - adapter->flags & FLAG_MSI_ENABLED ? "MSI":"INTx", err); - if (adapter->flags & FLAG_MSI_ENABLED) + if (adapter->flags & FLAG_MSI_ENABLED) { pci_disable_msi(adapter->pdev); + adapter->flags &= ~FLAG_MSI_ENABLED; + } + e_err("Unable to allocate interrupt, Error: %d\n", err); } return err; @@ -2594,6 +2604,135 @@ err: return -ENOMEM; } +/** + * e1000_intr_msi_test - Interrupt Handler + * @irq: interrupt number + * @data: pointer to a network interface device structure + **/ +static irqreturn_t e1000_intr_msi_test(int irq, void *data) +{ + struct net_device *netdev = data; + struct e1000_adapter *adapter = netdev_priv(netdev); + struct e1000_hw *hw = &adapter->hw; + u32 icr = er32(ICR); + + e_dbg("%s: icr is %08X\n", netdev->name, icr); + if (icr & E1000_ICR_RXSEQ) { + adapter->flags &= ~FLAG_MSI_TEST_FAILED; + wmb(); + } + + return IRQ_HANDLED; +} + +/** + * e1000_test_msi_interrupt - Returns 0 for successful test + * @adapter: board private struct + * + * code flow taken from tg3.c + **/ +static int e1000_test_msi_interrupt(struct e1000_adapter *adapter) +{ + struct net_device *netdev = adapter->netdev; + struct e1000_hw *hw = &adapter->hw; + int err; + + /* poll_enable hasn't been called yet, so don't need disable */ + /* clear any pending events */ + er32(ICR); + + /* free the real vector and request a test handler */ + e1000_free_irq(adapter); + + /* Assume that the test fails, if it succeeds then the test + * MSI irq handler will unset this flag */ + adapter->flags |= FLAG_MSI_TEST_FAILED; + + err = pci_enable_msi(adapter->pdev); + if (err) + goto msi_test_failed; + + err = request_irq(adapter->pdev->irq, &e1000_intr_msi_test, 0, + netdev->name, netdev); + if (err) { + pci_disable_msi(adapter->pdev); + goto msi_test_failed; + } + + wmb(); + + e1000_irq_enable(adapter); + + /* fire an unusual interrupt on the test handler */ + ew32(ICS, E1000_ICS_RXSEQ); + e1e_flush(); + msleep(50); + + e1000_irq_disable(adapter); + + rmb(); + + if (adapter->flags & FLAG_MSI_TEST_FAILED) { + err = -EIO; + e_info("MSI interrupt test failed!\n"); + } + + free_irq(adapter->pdev->irq, netdev); + pci_disable_msi(adapter->pdev); + + if (err == -EIO) + goto msi_test_failed; + + /* okay so the test worked, restore settings */ + e_dbg("%s: MSI interrupt test succeeded!\n", netdev->name); +msi_test_failed: + /* restore the original vector, even if it failed */ + e1000_request_irq(adapter); + return err; +} + +/** + * e1000_test_msi - Returns 0 if MSI test succeeds or INTx mode is restored + * @adapter: board private struct + * + * code flow taken from tg3.c, called with e1000 interrupts disabled. + **/ +static int e1000_test_msi(struct e1000_adapter *adapter) +{ + int err; + u16 pci_cmd; + + if (!(adapter->flags & FLAG_MSI_ENABLED)) + return 0; + + /* disable SERR in case the MSI write causes a master abort */ + pci_read_config_word(adapter->pdev, PCI_COMMAND, &pci_cmd); + pci_write_config_word(adapter->pdev, PCI_COMMAND, + pci_cmd & ~PCI_COMMAND_SERR); + + err = e1000_test_msi_interrupt(adapter); + + /* restore previous setting of command word */ + pci_write_config_word(adapter->pdev, PCI_COMMAND, pci_cmd); + + /* success ! */ + if (!err) + return 0; + + /* EIO means MSI test failed */ + if (err != -EIO) + return err; + + /* back to INTx mode */ + e_warn("MSI interrupt test failed, using legacy interrupt.\n"); + + e1000_free_irq(adapter); + + err = e1000_request_irq(adapter); + + return err; +} + /** * e1000_open - Called when a network interface is made active * @netdev: network interface device structure @@ -2652,6 +2791,19 @@ static int e1000_open(struct net_device *netdev) if (err) goto err_req_irq; + /* + * Work around PCIe errata with MSI interrupts causing some chipsets to + * ignore e1000e MSI messages, which means we need to test our MSI + * interrupt now + */ + { + err = e1000_test_msi(adapter); + if (err) { + e_err("Interrupt allocation failed\n"); + goto err_req_irq; + } + } + /* From here on the code is the same as e1000e_up() */ clear_bit(__E1000_DOWN, &adapter->state); -- GitLab From 05c550babecfc129a8d9331edf43107192bae115 Mon Sep 17 00:00:00 2001 From: Bruce Allan Date: Fri, 8 Aug 2008 18:36:16 -0700 Subject: [PATCH 348/750] e1000e: remove unnecessary snippet missed in prior check_options update The removal of this bit of code was missed in an earlier patch submittal. Signed-off-by: Bruce Allan Signed-off-by: Jeff Kirsher Signed-off-by: Jeff Garzik --- drivers/net/e1000e/param.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/drivers/net/e1000e/param.c b/drivers/net/e1000e/param.c index b0499f27e5f..ed912e023a7 100644 --- a/drivers/net/e1000e/param.c +++ b/drivers/net/e1000e/param.c @@ -324,8 +324,6 @@ void __devinit e1000e_check_options(struct e1000_adapter *adapter) adapter->itr = 20000; break; default: - e1000_validate_option(&adapter->itr, &opt, - adapter); /* * Save the setting, because the dynamic bits * change itr. -- GitLab From 8d792cd990938c4d06b86141465ff8d52a946a0a Mon Sep 17 00:00:00 2001 From: Jesse Brandeburg Date: Fri, 8 Aug 2008 16:24:19 -0700 Subject: [PATCH 349/750] ixgbe: add cx4 device ID This is a simple device ID add for adapters that support CX4 (copper infiniband style cable) connectors for 10GbE. Signed-off-by: Jesse Brandeburg Signed-off-by: Jeff Kirsher Signed-off-by: Jeff Garzik --- drivers/net/ixgbe/ixgbe_82598.c | 1 + drivers/net/ixgbe/ixgbe_main.c | 4 +++- drivers/net/ixgbe/ixgbe_type.h | 1 + 3 files changed, 5 insertions(+), 1 deletion(-) diff --git a/drivers/net/ixgbe/ixgbe_82598.c b/drivers/net/ixgbe/ixgbe_82598.c index 2f38e847e2c..f96358b641a 100644 --- a/drivers/net/ixgbe/ixgbe_82598.c +++ b/drivers/net/ixgbe/ixgbe_82598.c @@ -190,6 +190,7 @@ static enum ixgbe_media_type ixgbe_get_media_type_82598(struct ixgbe_hw *hw) case IXGBE_DEV_ID_82598AF_DUAL_PORT: case IXGBE_DEV_ID_82598AF_SINGLE_PORT: case IXGBE_DEV_ID_82598EB_CX4: + case IXGBE_DEV_ID_82598_CX4_DUAL_PORT: media_type = ixgbe_media_type_fiber; break; case IXGBE_DEV_ID_82598AT_DUAL_PORT: diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index e5f3da8468c..34bca16d48a 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -48,7 +48,7 @@ char ixgbe_driver_name[] = "ixgbe"; static const char ixgbe_driver_string[] = "Intel(R) 10 Gigabit PCI Express Network Driver"; -#define DRV_VERSION "1.3.18-k2" +#define DRV_VERSION "1.3.18-k4" const char ixgbe_driver_version[] = DRV_VERSION; static const char ixgbe_copyright[] = "Copyright (c) 1999-2007 Intel Corporation."; @@ -72,6 +72,8 @@ static struct pci_device_id ixgbe_pci_tbl[] = { board_82598 }, {PCI_VDEVICE(INTEL, IXGBE_DEV_ID_82598EB_CX4), board_82598 }, + {PCI_VDEVICE(INTEL, IXGBE_DEV_ID_82598_CX4_DUAL_PORT), + board_82598 }, /* required last entry */ {0, } diff --git a/drivers/net/ixgbe/ixgbe_type.h b/drivers/net/ixgbe/ixgbe_type.h index 1ad7cb9c25a..c0282a223df 100644 --- a/drivers/net/ixgbe/ixgbe_type.h +++ b/drivers/net/ixgbe/ixgbe_type.h @@ -39,6 +39,7 @@ #define IXGBE_DEV_ID_82598AF_SINGLE_PORT 0x10C7 #define IXGBE_DEV_ID_82598AT_DUAL_PORT 0x10C8 #define IXGBE_DEV_ID_82598EB_CX4 0x10DD +#define IXGBE_DEV_ID_82598_CX4_DUAL_PORT 0x10EC /* General Registers */ #define IXGBE_CTRL 0x00000 -- GitLab From 9dc28efeee98a4f81d5469d3576f55c5e6d1a5db Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Fri, 8 Aug 2008 00:08:39 -0700 Subject: [PATCH 350/750] netxen: fix mac addr setup For NX3031 mac addr should be read from firmware. mac addr in flash is still valid, but can be overridden by firmware if running in virtualization environment. For old revisions, mac addr is retrieved directly from flash. Signed-off-by: Dhananjay Phadke Signed-off-by: Jeff Garzik --- drivers/net/netxen/netxen_nic.h | 3 +- drivers/net/netxen/netxen_nic_hw.c | 51 ++++++++++++++----- drivers/net/netxen/netxen_nic_main.c | 65 +++++++++++++++--------- drivers/net/netxen/netxen_nic_phan_reg.h | 2 + 4 files changed, 83 insertions(+), 38 deletions(-) diff --git a/drivers/net/netxen/netxen_nic.h b/drivers/net/netxen/netxen_nic.h index 93a7b9b668d..2cf6e41291e 100644 --- a/drivers/net/netxen/netxen_nic.h +++ b/drivers/net/netxen/netxen_nic.h @@ -1615,7 +1615,8 @@ dma_watchdog_wakeup(struct netxen_adapter *adapter) int netxen_is_flash_supported(struct netxen_adapter *adapter); -int netxen_get_flash_mac_addr(struct netxen_adapter *adapter, __le64 mac[]); +int netxen_get_flash_mac_addr(struct netxen_adapter *adapter, __le64 *mac); +int netxen_p3_get_mac_addr(struct netxen_adapter *adapter, __le64 *mac); extern void netxen_change_ringparam(struct netxen_adapter *adapter); extern int netxen_rom_fast_read(struct netxen_adapter *adapter, int addr, int *valp); diff --git a/drivers/net/netxen/netxen_nic_hw.c b/drivers/net/netxen/netxen_nic_hw.c index 9aa20f96161..f5db48bcd26 100644 --- a/drivers/net/netxen/netxen_nic_hw.c +++ b/drivers/net/netxen/netxen_nic_hw.c @@ -733,31 +733,56 @@ static int netxen_get_flash_block(struct netxen_adapter *adapter, int base, return 0; } -int netxen_get_flash_mac_addr(struct netxen_adapter *adapter, __le64 mac[]) +int netxen_get_flash_mac_addr(struct netxen_adapter *adapter, __le64 *mac) { - __le32 *pmac = (__le32 *) & mac[0]; + __le32 *pmac = (__le32 *) mac; + u32 offset; - if (netxen_get_flash_block(adapter, - NETXEN_USER_START + - offsetof(struct netxen_new_user_info, - mac_addr), - FLASH_NUM_PORTS * sizeof(u64), pmac) == -1) { + offset = NETXEN_USER_START + + offsetof(struct netxen_new_user_info, mac_addr) + + adapter->portnum * sizeof(u64); + + if (netxen_get_flash_block(adapter, offset, sizeof(u64), pmac) == -1) return -1; - } + if (*mac == cpu_to_le64(~0ULL)) { + + offset = NETXEN_USER_START_OLD + + offsetof(struct netxen_user_old_info, mac_addr) + + adapter->portnum * sizeof(u64); + if (netxen_get_flash_block(adapter, - NETXEN_USER_START_OLD + - offsetof(struct netxen_user_old_info, - mac_addr), - FLASH_NUM_PORTS * sizeof(u64), - pmac) == -1) + offset, sizeof(u64), pmac) == -1) return -1; + if (*mac == cpu_to_le64(~0ULL)) return -1; } return 0; } +int netxen_p3_get_mac_addr(struct netxen_adapter *adapter, __le64 *mac) +{ + uint32_t crbaddr, mac_hi, mac_lo; + int pci_func = adapter->ahw.pci_func; + + crbaddr = CRB_MAC_BLOCK_START + + (4 * ((pci_func/2) * 3)) + (4 * (pci_func & 1)); + + adapter->hw_read_wx(adapter, crbaddr, &mac_lo, 4); + adapter->hw_read_wx(adapter, crbaddr+4, &mac_hi, 4); + + mac_hi = cpu_to_le32(mac_hi); + mac_lo = cpu_to_le32(mac_lo); + + if (pci_func & 1) + *mac = ((mac_lo >> 16) | ((u64)mac_hi << 16)); + else + *mac = ((mac_lo) | ((u64)mac_hi << 32)); + + return 0; +} + #define CRB_WIN_LOCK_TIMEOUT 100000000 static int crb_win_lock(struct netxen_adapter *adapter) diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index 7615c715e66..6fc42cd3072 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -501,6 +501,44 @@ static void netxen_init_msix_entries(struct netxen_adapter *adapter) adapter->msix_entries[i].entry = i; } +static int +netxen_read_mac_addr(struct netxen_adapter *adapter) +{ + int i; + unsigned char *p; + __le64 mac_addr; + DECLARE_MAC_BUF(mac); + struct net_device *netdev = adapter->netdev; + struct pci_dev *pdev = adapter->pdev; + + if (netxen_is_flash_supported(adapter) != 0) + return -EIO; + + if (NX_IS_REVISION_P3(adapter->ahw.revision_id)) { + if (netxen_p3_get_mac_addr(adapter, &mac_addr) != 0) + return -EIO; + } else { + if (netxen_get_flash_mac_addr(adapter, &mac_addr) != 0) + return -EIO; + } + + p = (unsigned char *)&mac_addr; + for (i = 0; i < 6; i++) + netdev->dev_addr[i] = *(p + 5 - i); + + memcpy(netdev->perm_addr, netdev->dev_addr, netdev->addr_len); + + /* set station address */ + + if (!is_valid_ether_addr(netdev->perm_addr)) { + dev_warn(&pdev->dev, "Bad MAC address %s.\n", + print_mac(mac, netdev->dev_addr)); + } else + adapter->macaddr_set(adapter, netdev->dev_addr); + + return 0; +} + /* * netxen_nic_probe() * @@ -529,10 +567,8 @@ netxen_nic_probe(struct pci_dev *pdev, const struct pci_device_id *ent) unsigned long mem_base, mem_len, db_base, db_len, pci_len0 = 0; int i = 0, err; int first_driver, first_boot; - __le64 mac_addr[FLASH_NUM_PORTS + 1]; u32 val; int pci_func_id = PCI_FUNC(pdev->devfn); - DECLARE_MAC_BUF(mac); struct netxen_legacy_intr_set *legacy_intrp; uint8_t revision_id; @@ -904,28 +940,9 @@ request_msi: INIT_WORK(&adapter->watchdog_task, netxen_watchdog_task); INIT_WORK(&adapter->tx_timeout_task, netxen_tx_timeout_task); - if (netxen_is_flash_supported(adapter) == 0 && - netxen_get_flash_mac_addr(adapter, mac_addr) == 0) { - unsigned char *p; - - p = (unsigned char *)&mac_addr[adapter->portnum]; - netdev->dev_addr[0] = *(p + 5); - netdev->dev_addr[1] = *(p + 4); - netdev->dev_addr[2] = *(p + 3); - netdev->dev_addr[3] = *(p + 2); - netdev->dev_addr[4] = *(p + 1); - netdev->dev_addr[5] = *(p + 0); - - memcpy(netdev->perm_addr, netdev->dev_addr, - netdev->addr_len); - if (!is_valid_ether_addr(netdev->perm_addr)) { - printk(KERN_ERR "%s: Bad MAC address %s.\n", - netxen_nic_driver_name, - print_mac(mac, netdev->dev_addr)); - } else { - adapter->macaddr_set(adapter, netdev->dev_addr); - } - } + err = netxen_read_mac_addr(adapter); + if (err) + dev_warn(&pdev->dev, "failed to read mac addr\n"); netif_carrier_off(netdev); netif_stop_queue(netdev); diff --git a/drivers/net/netxen/netxen_nic_phan_reg.h b/drivers/net/netxen/netxen_nic_phan_reg.h index 83e5ee57bfe..b293adcc95a 100644 --- a/drivers/net/netxen/netxen_nic_phan_reg.h +++ b/drivers/net/netxen/netxen_nic_phan_reg.h @@ -125,6 +125,8 @@ #define CRB_SW_INT_MASK_2 NETXEN_NIC_REG(0x1e4) #define CRB_SW_INT_MASK_3 NETXEN_NIC_REG(0x1e8) +#define CRB_MAC_BLOCK_START NETXEN_CAM_RAM(0x1c0) + /* * capabilities register, can be used to selectively enable/disable features * for backward compability -- GitLab From 9e410778047d0f2887adb888b44eda4d72d4f67d Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Fri, 8 Aug 2008 00:08:40 -0700 Subject: [PATCH 351/750] netxen: fix rxbuf leak across driver reload Free up rx ring during driver unload or open() failure. Signed-off-by: Dhananjay Phadke Signed-off-by: Jeff Garzik --- drivers/net/netxen/netxen_nic_main.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index 6fc42cd3072..056f6b17a33 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -1017,6 +1017,7 @@ static void __devexit netxen_nic_remove(struct pci_dev *pdev) if (adapter->is_up == NETXEN_ADAPTER_UP_MAGIC) { netxen_free_hw_resources(adapter); + netxen_release_rx_buffers(adapter); netxen_free_sw_resources(adapter); } @@ -1111,7 +1112,7 @@ static int netxen_nic_open(struct net_device *netdev) flags, netdev->name, adapter); if (err) { printk(KERN_ERR "request_irq failed with: %d\n", err); - goto err_out_free_hw; + goto err_out_free_rxbuf; } adapter->is_up = NETXEN_ADAPTER_UP_MAGIC; @@ -1144,7 +1145,8 @@ static int netxen_nic_open(struct net_device *netdev) err_out_free_irq: free_irq(adapter->irq, adapter); -err_out_free_hw: +err_out_free_rxbuf: + netxen_release_rx_buffers(adapter); netxen_free_hw_resources(adapter); err_out_free_sw: netxen_free_sw_resources(adapter); -- GitLab From 922c4f2c70c156ac38b4e6affbd30d4b1efd5864 Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Fri, 8 Aug 2008 00:08:41 -0700 Subject: [PATCH 352/750] netxen: force link update across ifdown/ifup Re-read link status in dev open(). Schedule link watchdog only if dev is up. Signed-off-by: Dhananjay Phadke Signed-off-by: Jeff Garzik --- drivers/net/netxen/netxen_nic_main.c | 11 +++++------ 1 file changed, 5 insertions(+), 6 deletions(-) diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index 056f6b17a33..f69807c9432 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -934,7 +934,6 @@ request_msi: goto err_out_disable_msi; init_timer(&adapter->watchdog_timer); - adapter->ahw.linkup = 0; adapter->watchdog_timer.function = &netxen_watchdog; adapter->watchdog_timer.data = (unsigned long)adapter; INIT_WORK(&adapter->watchdog_task, netxen_watchdog_task); @@ -1134,6 +1133,7 @@ static int netxen_nic_open(struct net_device *netdev) if (adapter->set_mtu) adapter->set_mtu(adapter, netdev->mtu); + adapter->ahw.linkup = 0; mod_timer(&adapter->watchdog_timer, jiffies); napi_enable(&adapter->napi); @@ -1171,10 +1171,8 @@ static int netxen_nic_close(struct net_device *netdev) netxen_release_tx_buffers(adapter); - if (adapter->is_up == NETXEN_ADAPTER_UP_MAGIC) { - FLUSH_SCHEDULED_WORK(); - del_timer_sync(&adapter->watchdog_timer); - } + FLUSH_SCHEDULED_WORK(); + del_timer_sync(&adapter->watchdog_timer); return 0; } @@ -1477,7 +1475,8 @@ void netxen_watchdog_task(struct work_struct *work) netxen_nic_handle_phy_intr(adapter); - mod_timer(&adapter->watchdog_timer, jiffies + 2 * HZ); + if (netif_running(adapter->netdev)) + mod_timer(&adapter->watchdog_timer, jiffies + 2 * HZ); } static void netxen_tx_timeout(struct net_device *netdev) -- GitLab From 15eef1e1b718667981da92d2fa18283f181c117c Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Fri, 8 Aug 2008 00:08:42 -0700 Subject: [PATCH 353/750] netxen: fix dma watchdog NX3031 does not require driver to kill dma watchdog. Signed-off-by: Dhananjay Phadke Signed-off-by: Jeff Garzik --- drivers/net/netxen/netxen_nic_init.c | 28 +++++++++++++++------------- 1 file changed, 15 insertions(+), 13 deletions(-) diff --git a/drivers/net/netxen/netxen_nic_init.c b/drivers/net/netxen/netxen_nic_init.c index 519fc860e17..5bba675d050 100644 --- a/drivers/net/netxen/netxen_nic_init.c +++ b/drivers/net/netxen/netxen_nic_init.c @@ -1079,10 +1079,12 @@ int netxen_initialize_adapter_offload(struct netxen_adapter *adapter) void netxen_free_adapter_offload(struct netxen_adapter *adapter) { - int i; + int i = 100; + + if (!adapter->dummy_dma.addr) + return; - if (adapter->dummy_dma.addr) { - i = 100; + if (NX_IS_REVISION_P2(adapter->ahw.revision_id)) { do { if (dma_watchdog_shutdown_request(adapter) == 1) break; @@ -1090,17 +1092,17 @@ void netxen_free_adapter_offload(struct netxen_adapter *adapter) if (dma_watchdog_shutdown_poll_result(adapter) == 1) break; } while (--i); + } - if (i) { - pci_free_consistent(adapter->pdev, - NETXEN_HOST_DUMMY_DMA_SIZE, - adapter->dummy_dma.addr, - adapter->dummy_dma.phys_addr); - adapter->dummy_dma.addr = NULL; - } else { - printk(KERN_ERR "%s: dma_watchdog_shutdown failed\n", - adapter->netdev->name); - } + if (i) { + pci_free_consistent(adapter->pdev, + NETXEN_HOST_DUMMY_DMA_SIZE, + adapter->dummy_dma.addr, + adapter->dummy_dma.phys_addr); + adapter->dummy_dma.addr = NULL; + } else { + printk(KERN_ERR "%s: dma_watchdog_shutdown failed\n", + adapter->netdev->name); } } -- GitLab From 092bc57184842229ee41f87d9c408a3f1302aaa6 Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Fri, 8 Aug 2008 00:08:43 -0700 Subject: [PATCH 354/750] netxen: cleanup interrupt code Mark interrupt scheme in very old firmware incompatible. Interrupt mask and status registers are per pci function / port. Signed-off-by: Dhananjay Phadke Signed-off-by: Jeff Garzik --- drivers/net/netxen/netxen_nic_main.c | 123 +++++++++------------------ 1 file changed, 40 insertions(+), 83 deletions(-) diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index f69807c9432..3c424a88d8f 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -149,76 +149,18 @@ static uint32_t msi_tgt_status[8] = { static struct netxen_legacy_intr_set legacy_intr[] = NX_LEGACY_INTR_CONFIG; -static void netxen_nic_disable_int(struct netxen_adapter *adapter) +static inline void netxen_nic_disable_int(struct netxen_adapter *adapter) { - u32 mask = 0x7ff; - int retries = 32; - int pci_fn = adapter->ahw.pci_func; - - if (adapter->msi_mode != MSI_MODE_MULTIFUNC) - adapter->pci_write_normalize(adapter, - adapter->crb_intr_mask, 0); - - if (adapter->intr_scheme != -1 && - adapter->intr_scheme != INTR_SCHEME_PERPORT) - adapter->pci_write_immediate(adapter, ISR_INT_MASK, mask); - - if (!NETXEN_IS_MSI_FAMILY(adapter)) { - do { - adapter->pci_write_immediate(adapter, - adapter->legacy_intr.tgt_status_reg, - 0xffffffff); - mask = adapter->pci_read_immediate(adapter, - ISR_INT_VECTOR); - if (!(mask & 0x80)) - break; - udelay(10); - } while (--retries); - - if (!retries) { - printk(KERN_NOTICE "%s: Failed to disable interrupt\n", - netxen_nic_driver_name); - } - } else { - if (adapter->msi_mode == MSI_MODE_MULTIFUNC) { - adapter->pci_write_immediate(adapter, - msi_tgt_status[pci_fn], 0xffffffff); - } - } + adapter->pci_write_normalize(adapter, adapter->crb_intr_mask, 0); } -static void netxen_nic_enable_int(struct netxen_adapter *adapter) +static inline void netxen_nic_enable_int(struct netxen_adapter *adapter) { - u32 mask; - - if (adapter->intr_scheme != -1 && - adapter->intr_scheme != INTR_SCHEME_PERPORT) { - switch (adapter->ahw.board_type) { - case NETXEN_NIC_GBE: - mask = 0x77b; - break; - case NETXEN_NIC_XGBE: - mask = 0x77f; - break; - default: - mask = 0x7ff; - break; - } - - adapter->pci_write_immediate(adapter, ISR_INT_MASK, mask); - } - adapter->pci_write_normalize(adapter, adapter->crb_intr_mask, 0x1); - if (!NETXEN_IS_MSI_FAMILY(adapter)) { - mask = 0xbff; - if (adapter->intr_scheme == INTR_SCHEME_PERPORT) - adapter->pci_write_immediate(adapter, - adapter->legacy_intr.tgt_mask_reg, mask); - else - adapter->pci_write_normalize(adapter, - CRB_INT_VECTOR, 0); - } + if (!NETXEN_IS_MSI_FAMILY(adapter)) + adapter->pci_write_immediate(adapter, + adapter->legacy_intr.tgt_mask_reg, 0xfbff); } static int nx_set_dma_mask(struct netxen_adapter *adapter, uint8_t revision_id) @@ -1086,6 +1028,15 @@ static int netxen_nic_open(struct net_device *netdev) goto err_out_free_sw; } + if ((adapter->msi_mode != MSI_MODE_MULTIFUNC) || + (adapter->intr_scheme != INTR_SCHEME_PERPORT)) { + printk(KERN_ERR "%s: Firmware interrupt scheme is " + "incompatible with driver\n", + netdev->name); + adapter->driver_mismatch = 1; + goto err_out_free_hw; + } + if (adapter->fw_major < 4) { adapter->crb_addr_cmd_producer = crb_cmd_producer[adapter->portnum]; @@ -1147,6 +1098,7 @@ err_out_free_irq: free_irq(adapter->irq, adapter); err_out_free_rxbuf: netxen_release_rx_buffers(adapter); +err_out_free_hw: netxen_free_hw_resources(adapter); err_out_free_sw: netxen_free_sw_resources(adapter); @@ -1536,18 +1488,9 @@ struct net_device_stats *netxen_nic_get_stats(struct net_device *netdev) return stats; } -static inline void -netxen_handle_int(struct netxen_adapter *adapter) -{ - netxen_nic_disable_int(adapter); - napi_schedule(&adapter->napi); -} - static irqreturn_t netxen_intr(int irq, void *data) { struct netxen_adapter *adapter = data; - u32 our_int = 0; - u32 status = 0; status = adapter->pci_read_immediate(adapter, ISR_INT_VECTOR); @@ -1562,22 +1505,32 @@ static irqreturn_t netxen_intr(int irq, void *data) if (!ISR_LEGACY_INT_TRIGGERED(status)) return IRQ_NONE; - } else if (NX_IS_REVISION_P2(adapter->ahw.revision_id)) { + } else { + unsigned long our_int = 0; our_int = adapter->pci_read_normalize(adapter, CRB_INT_VECTOR); + /* not our interrupt */ - if ((our_int & (0x80 << adapter->portnum)) == 0) + if (!test_and_clear_bit((7 + adapter->portnum), &our_int)) return IRQ_NONE; - if (adapter->intr_scheme == INTR_SCHEME_PERPORT) { - /* claim interrupt */ - adapter->pci_write_normalize(adapter, - CRB_INT_VECTOR, - our_int & ~((u32)(0x80 << adapter->portnum))); - } + /* claim interrupt */ + adapter->pci_write_normalize(adapter, + CRB_INT_VECTOR, (our_int & 0xffffffff)); } - netxen_handle_int(adapter); + /* clear interrupt */ + if (adapter->fw_major < 4) + netxen_nic_disable_int(adapter); + + adapter->pci_write_immediate(adapter, + adapter->legacy_intr.tgt_status_reg, + 0xffffffff); + /* read twice to ensure write is flushed */ + adapter->pci_read_immediate(adapter, ISR_INT_VECTOR); + adapter->pci_read_immediate(adapter, ISR_INT_VECTOR); + + napi_schedule(&adapter->napi); return IRQ_HANDLED; } @@ -1586,7 +1539,11 @@ static irqreturn_t netxen_msi_intr(int irq, void *data) { struct netxen_adapter *adapter = data; - netxen_handle_int(adapter); + /* clear interrupt */ + adapter->pci_write_immediate(adapter, + msi_tgt_status[adapter->ahw.pci_func], 0xffffffff); + + napi_schedule(&adapter->napi); return IRQ_HANDLED; } -- GitLab From 11d89d639352ef27bb3f0e7513dd406284bf034a Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Fri, 8 Aug 2008 00:08:45 -0700 Subject: [PATCH 355/750] netxen: update driver version Raise driver version to 4.0.11. Signed-off-by: Dhananjay Phadke Signed-off-by: Jeff Garzik --- drivers/net/netxen/netxen_nic.h | 4 ++-- drivers/net/netxen/netxen_nic_hw.c | 8 ++++---- drivers/net/netxen/netxen_nic_main.c | 7 +++++++ 3 files changed, 13 insertions(+), 6 deletions(-) diff --git a/drivers/net/netxen/netxen_nic.h b/drivers/net/netxen/netxen_nic.h index 2cf6e41291e..ab871df6b1d 100644 --- a/drivers/net/netxen/netxen_nic.h +++ b/drivers/net/netxen/netxen_nic.h @@ -66,8 +66,8 @@ #define _NETXEN_NIC_LINUX_MAJOR 4 #define _NETXEN_NIC_LINUX_MINOR 0 -#define _NETXEN_NIC_LINUX_SUBVERSION 0 -#define NETXEN_NIC_LINUX_VERSIONID "4.0.0" +#define _NETXEN_NIC_LINUX_SUBVERSION 11 +#define NETXEN_NIC_LINUX_VERSIONID "4.0.11" #define NETXEN_VERSION_CODE(a, b, c) (((a) << 16) + ((b) << 8) + (c)) diff --git a/drivers/net/netxen/netxen_nic_hw.c b/drivers/net/netxen/netxen_nic_hw.c index f5db48bcd26..84978f80f39 100644 --- a/drivers/net/netxen/netxen_nic_hw.c +++ b/drivers/net/netxen/netxen_nic_hw.c @@ -2208,10 +2208,10 @@ void netxen_nic_flash_print(struct netxen_adapter *adapter) if (adapter->portnum == 0) { get_brd_name_by_type(board_info->board_type, brd_name); - printk("NetXen %s Board S/N %s Chip id 0x%x\n", - brd_name, serial_num, board_info->chip_id); - printk("NetXen Firmware version %d.%d.%d\n", fw_major, - fw_minor, fw_build); + printk(KERN_INFO "NetXen %s Board S/N %s Chip rev 0x%x\n", + brd_name, serial_num, adapter->ahw.revision_id); + printk(KERN_INFO "NetXen Firmware version %d.%d.%d\n", + fw_major, fw_minor, fw_build); } if (NETXEN_VERSION_CODE(fw_major, fw_minor, fw_build) < diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index 3c424a88d8f..32bb47adbe3 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -523,6 +523,13 @@ netxen_nic_probe(struct pci_dev *pdev, const struct pci_device_id *ent) return -ENODEV; } + if (pdev->revision >= NX_P3_A0 && pdev->revision < NX_P3_B1) { + printk(KERN_WARNING "NetXen chip revisions between 0x%x-0x%x" + "will not be enabled.\n", + NX_P3_A0, NX_P3_B1); + return -ENODEV; + } + if ((err = pci_enable_device(pdev))) return err; -- GitLab From 1595ab5d7d99bc6c9a5548ab3fb83e278eeae409 Mon Sep 17 00:00:00 2001 From: Adrian Bunk Date: Fri, 8 Aug 2008 21:33:34 +0300 Subject: [PATCH 356/750] [netdrvr] uninline atl1e_setup_mac_ctrl() There doesn't seem to be a compelling reason why atl1e_setup_mac_ctrl() is marked as "inline": It's not used in any place where speed would matter much, and as long as it has only one caller non-ancient gcc versions anyway inline it automatically. This patch fixes the following compile error with gcc 3.4: <-- snip --> ... CC drivers/net/atl1e/atl1e_main.o atl1e_main.c: In function `atl1e_check_link': atl1e_main.c:50: sorry, unimplemented: inlining failed in call to atl1e_main.c:196: sorry, unimplemented: called from here make[4]: *** [drivers/net/atl1e/atl1e_main.o] Error 1 <-- snip --> Reported-by: Adrian Bunk Signed-off-by: Adrian Bunk Signed-off-by: Jeff Garzik --- drivers/net/atl1e/atl1e_main.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/atl1e/atl1e_main.c b/drivers/net/atl1e/atl1e_main.c index 35264c244cf..82d7be1655d 100644 --- a/drivers/net/atl1e/atl1e_main.c +++ b/drivers/net/atl1e/atl1e_main.c @@ -47,7 +47,7 @@ MODULE_DESCRIPTION("Atheros 1000M Ethernet Network Driver"); MODULE_LICENSE("GPL"); MODULE_VERSION(DRV_VERSION); -static inline void atl1e_setup_mac_ctrl(struct atl1e_adapter *adapter); +static void atl1e_setup_mac_ctrl(struct atl1e_adapter *adapter); static const u16 atl1e_rx_page_vld_regs[AT_MAX_RECEIVE_QUEUE][AT_PAGE_NUM_PER_QUEUE] = @@ -1037,7 +1037,7 @@ static inline void atl1e_configure_dma(struct atl1e_adapter *adapter) return; } -static inline void atl1e_setup_mac_ctrl(struct atl1e_adapter *adapter) +static void atl1e_setup_mac_ctrl(struct atl1e_adapter *adapter) { u32 value; struct atl1e_hw *hw = &adapter->hw; -- GitLab From add477df674db00377d9a4dc0d9b553ce79bc06d Mon Sep 17 00:00:00 2001 From: Olivier Blin Date: Fri, 8 Aug 2008 12:01:11 -0700 Subject: [PATCH 357/750] hso: fix oops in read/write callbacks The tty may be closed already when the read/write callbacks are called. This patch checks that the ttys still exist before waking them up. Signed-off-by: Olivier Blin Acked-by: Alan Cox Cc: Jari Tenhunen Signed-off-by: Greg Kroah-Hartman Signed-off-by: Jeff Garzik --- drivers/net/usb/hso.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/net/usb/hso.c b/drivers/net/usb/hso.c index 031d07b105a..94a27f764e6 100644 --- a/drivers/net/usb/hso.c +++ b/drivers/net/usb/hso.c @@ -1467,7 +1467,8 @@ static void hso_std_serial_write_bulk_callback(struct urb *urb) return; } hso_put_activity(serial->parent); - tty_wakeup(serial->tty); + if (serial->tty) + tty_wakeup(serial->tty); hso_kick_transmit(serial); D1(" "); @@ -1538,7 +1539,8 @@ static void ctrl_callback(struct urb *urb) clear_bit(HSO_SERIAL_FLAG_RX_SENT, &serial->flags); } else { hso_put_activity(serial->parent); - tty_wakeup(serial->tty); + if (serial->tty) + tty_wakeup(serial->tty); /* response to a write command */ hso_kick_transmit(serial); } -- GitLab From 6d558a52ba295fc1c281c671d7daab2f74ddb4f2 Mon Sep 17 00:00:00 2001 From: Olivier Blin Date: Fri, 8 Aug 2008 12:01:41 -0700 Subject: [PATCH 358/750] hso: fix refcounting on the ttyHSx devices The references on ttyHSx devices were not decremented correctly when the tty was closed. The helper freeing the serial devices was never called because of that, and the module left some dangling sysfs devices after being unloaded. Signed-off-by: Olivier Blin Cc: Jari Tenhunen Signed-off-by: Greg Kroah-Hartman Signed-off-by: Jeff Garzik --- drivers/net/usb/hso.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/usb/hso.c b/drivers/net/usb/hso.c index 94a27f764e6..94c41bbedee 100644 --- a/drivers/net/usb/hso.c +++ b/drivers/net/usb/hso.c @@ -1103,8 +1103,8 @@ static void hso_serial_close(struct tty_struct *tty, struct file *filp) /* reset the rts and dtr */ /* do the actual close */ serial->open_count--; + kref_put(&serial->parent->ref, hso_serial_ref_free); if (serial->open_count <= 0) { - kref_put(&serial->parent->ref, hso_serial_ref_free); serial->open_count = 0; if (serial->tty) { serial->tty->driver_data = NULL; -- GitLab From 6c59f56978c3dffd447176d218bc5852842c9ce9 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Fri, 8 Aug 2008 12:02:14 -0700 Subject: [PATCH 359/750] USB: HSO: make tty_operations const As recommended by Arjan. Cc: Arjan van de Ven Cc: Andrew Bird Signed-off-by: Greg Kroah-Hartman Signed-off-by: Jeff Garzik --- drivers/net/usb/hso.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/usb/hso.c b/drivers/net/usb/hso.c index 94c41bbedee..35a7772cf1a 100644 --- a/drivers/net/usb/hso.c +++ b/drivers/net/usb/hso.c @@ -2725,7 +2725,7 @@ static int hso_mux_submit_intr_urb(struct hso_shared_int *shared_int, } /* operations setup of the serial interface */ -static struct tty_operations hso_serial_ops = { +static const struct tty_operations hso_serial_ops = { .open = hso_serial_open, .close = hso_serial_close, .write = hso_serial_write, -- GitLab From 0235f64175db41fa17a6ce5c9b58fd3550986eb4 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Fri, 8 Aug 2008 12:02:57 -0700 Subject: [PATCH 360/750] USB: HSO: minor fixes due to code review Fix up problems in hso.c driver as pointed out by Andrew. Cc: Andrew Morton Signed-off-by: Greg Kroah-Hartman Signed-off-by: Jeff Garzik --- drivers/net/usb/hso.c | 43 ++++++++++++++++++++++++------------------- 1 file changed, 24 insertions(+), 19 deletions(-) diff --git a/drivers/net/usb/hso.c b/drivers/net/usb/hso.c index 35a7772cf1a..1b7cac77159 100644 --- a/drivers/net/usb/hso.c +++ b/drivers/net/usb/hso.c @@ -102,8 +102,12 @@ #define MAX_RX_URBS 2 -#define get_serial_by_tty(x) \ - (x ? (struct hso_serial *)x->driver_data : NULL) +static inline struct hso_serial *get_serial_by_tty(struct tty_struct *tty) +{ + if (tty) + return tty->driver_data; + return NULL; +} /*****************************************************************************/ /* Debugging functions */ @@ -294,24 +298,25 @@ static int hso_get_activity(struct hso_device *hso_dev); /* #define DEBUG */ -#define dev2net(x) (x->port_data.dev_net) -#define dev2ser(x) (x->port_data.dev_serial) +static inline struct hso_net *dev2net(struct hso_device *hso_dev) +{ + return hso_dev->port_data.dev_net; +} + +static inline struct hso_serial *dev2ser(struct hso_device *hso_dev) +{ + return hso_dev->port_data.dev_serial; +} /* Debugging functions */ #ifdef DEBUG static void dbg_dump(int line_count, const char *func_name, unsigned char *buf, unsigned int len) { - u8 i = 0; - - printk(KERN_DEBUG "[%d:%s]: len %d", line_count, func_name, len); + static char name[255]; - for (i = 0; i < len; i++) { - if (!(i % 16)) - printk("\n 0x%03x: ", i); - printk("%02x ", (unsigned char)buf[i]); - } - printk("\n"); + sprintf(name, "hso[%d:%s]", line_count, func_name); + print_hex_dump_bytes(name, DUMP_PREFIX_NONE, buf, len); } #define DUMP(buf_, len_) \ @@ -528,13 +533,12 @@ static struct hso_serial *get_serial_by_shared_int_and_type( static struct hso_serial *get_serial_by_index(unsigned index) { - struct hso_serial *serial; + struct hso_serial *serial = NULL; unsigned long flags; - if (!serial_table[index]) - return NULL; spin_lock_irqsave(&serial_table_lock, flags); - serial = dev2ser(serial_table[index]); + if (serial_table[index]) + serial = dev2ser(serial_table[index]); spin_unlock_irqrestore(&serial_table_lock, flags); return serial; @@ -561,6 +565,7 @@ static int get_free_serial_index(void) static void set_serial_by_index(unsigned index, struct hso_serial *serial) { unsigned long flags; + spin_lock_irqsave(&serial_table_lock, flags); if (serial) serial_table[index] = serial->parent; @@ -569,7 +574,7 @@ static void set_serial_by_index(unsigned index, struct hso_serial *serial) spin_unlock_irqrestore(&serial_table_lock, flags); } -/* log a meaningfull explanation of an USB status */ +/* log a meaningful explanation of an USB status */ static void log_usb_status(int status, const char *function) { char *explanation; @@ -2654,7 +2659,7 @@ static void hso_free_interface(struct usb_interface *interface) hso_stop_net_device(network_table[i]); cancel_work_sync(&network_table[i]->async_put_intf); cancel_work_sync(&network_table[i]->async_get_intf); - if(rfk) + if (rfk) rfkill_unregister(rfk); hso_free_net_device(network_table[i]); } -- GitLab From 85a73b333c0c06fcadb8e32f1e30f00e980f2fc7 Mon Sep 17 00:00:00 2001 From: David Brownell Date: Fri, 8 Aug 2008 13:53:29 -0700 Subject: [PATCH 361/750] Kconfig: HSO driver bugfixes and updates Move the Kconfig for the new "Option" driver so it's not in the middle of the usbnet-based drivers, so the dependency displays in the Kconfig user interfaces don't get trashed. Signed-off-by: David Brownell Signed-off-by: Jeff Garzik --- drivers/net/usb/Kconfig | 21 ++++++++++----------- 1 file changed, 10 insertions(+), 11 deletions(-) diff --git a/drivers/net/usb/Kconfig b/drivers/net/usb/Kconfig index 68e198bd538..0973b6e3702 100644 --- a/drivers/net/usb/Kconfig +++ b/drivers/net/usb/Kconfig @@ -154,17 +154,6 @@ config USB_NET_AX8817X This driver creates an interface named "ethX", where X depends on what other networking devices you have in use. -config USB_HSO - tristate "Option USB High Speed Mobile Devices" - depends on USB && RFKILL - default n - help - Choose this option if you have an Option HSDPA/HSUPA card. - These cards support downlink speeds of 7.2Mbps or greater. - - To compile this driver as a module, choose M here: the - module will be called hso. - config USB_NET_CDCETHER tristate "CDC Ethernet support (smart devices such as cable modems)" depends on USB_USBNET @@ -337,5 +326,15 @@ config USB_NET_ZAURUS really need this non-conformant variant of CDC Ethernet (or in some cases CDC MDLM) protocol, not "g_ether". +config USB_HSO + tristate "Option USB High Speed Mobile Devices" + depends on USB && RFKILL + default n + help + Choose this option if you have an Option HSDPA/HSUPA card. + These cards support downlink speeds of 7.2Mbps or greater. + + To compile this driver as a module, choose M here: the + module will be called hso. endmenu -- GitLab From c7e65c17d75f29c846ff711b1dc5e823ba8de314 Mon Sep 17 00:00:00 2001 From: Atsushi Nemoto Date: Fri, 8 Aug 2008 00:55:17 +0900 Subject: [PATCH 362/750] [netdrvr] ne: Use CONFIG_MACH_TX49XX After some cleanups in arch/mips area, now MACH_TX49XX is selected for both TOSHIBA_RBTX4927 and TOSHIBA_RBTX4938. Fold these two conditions to one. Signed-off-by: Atsushi Nemoto Signed-off-by: Jeff Garzik --- drivers/net/Kconfig | 2 +- drivers/net/ne.c | 4 ++-- 2 files changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 4b4cb2bf4f1..a5c141cecd4 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -1172,7 +1172,7 @@ config ETH16I config NE2000 tristate "NE2000/NE1000 support" - depends on NET_ISA || (Q40 && m) || M32R || TOSHIBA_RBTX4927 || TOSHIBA_RBTX4938 + depends on NET_ISA || (Q40 && m) || M32R || MACH_TX49XX select CRC32 ---help--- If you have a network (Ethernet) card of this type, say Y and read diff --git a/drivers/net/ne.c b/drivers/net/ne.c index 42443d69742..fa3ceca4e15 100644 --- a/drivers/net/ne.c +++ b/drivers/net/ne.c @@ -118,7 +118,7 @@ bad_clone_list[] __initdata = { {"E-LAN100", "E-LAN200", {0x00, 0x00, 0x5d}}, /* Broken ne1000 clones */ {"PCM-4823", "PCM-4823", {0x00, 0xc0, 0x6c}}, /* Broken Advantech MoBo */ {"REALTEK", "RTL8019", {0x00, 0x00, 0xe8}}, /* no-name with Realtek chip */ -#if defined(CONFIG_TOSHIBA_RBTX4927) || defined(CONFIG_TOSHIBA_RBTX4938) +#ifdef CONFIG_MACH_TX49XX {"RBHMA4X00-RTL8019", "RBHMA4X00/RTL8019", {0x00, 0x60, 0x0a}}, /* Toshiba built-in */ #endif {"LCS-8834", "LCS-8836", {0x04, 0x04, 0x37}}, /* ShinyNet (SET) */ @@ -142,7 +142,7 @@ bad_clone_list[] __initdata = { #if defined(CONFIG_PLAT_MAPPI) # define DCR_VAL 0x4b #elif defined(CONFIG_PLAT_OAKS32R) || \ - defined(CONFIG_TOSHIBA_RBTX4927) || defined(CONFIG_TOSHIBA_RBTX4938) + defined(CONFIG_MACH_TX49XX) # define DCR_VAL 0x48 /* 8-bit mode */ #else # define DCR_VAL 0x49 -- GitLab From 5430c72b14a06b12e8fe46bca18ca0d7095fb717 Mon Sep 17 00:00:00 2001 From: Clemens Ladisch Date: Mon, 28 Jul 2008 10:28:43 +0200 Subject: [PATCH 363/750] ALSA: virtuoso: add Xonar D1 support Add support for the Asus Xonar D1. It is the same as the DX, but without the external power detection. Signed-off-by: Clemens Ladisch Signed-off-by: Takashi Iwai --- .../sound/alsa/ALSA-Configuration.txt | 10 +-- sound/pci/Kconfig | 2 +- sound/pci/oxygen/virtuoso.c | 73 ++++++++++++++----- 3 files changed, 58 insertions(+), 27 deletions(-) diff --git a/Documentation/sound/alsa/ALSA-Configuration.txt b/Documentation/sound/alsa/ALSA-Configuration.txt index 6f6d117ac7e..b117e42a616 100644 --- a/Documentation/sound/alsa/ALSA-Configuration.txt +++ b/Documentation/sound/alsa/ALSA-Configuration.txt @@ -1144,8 +1144,6 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. This module supports autoprobe and multiple cards. - Power management is _not_ supported. - Module snd-ice1712 ------------------ @@ -1628,8 +1626,6 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. This module supports autoprobe and multiple cards. - Power management is _not_ supported. - Module snd-pcsp ----------------- @@ -2081,13 +2077,11 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. Module snd-virtuoso ------------------- - Module for sound cards based on the Asus AV200 chip, i.e., - Xonar D2 and Xonar D2X. + Module for sound cards based on the Asus AV100/AV200 chips, + i.e., Xonar D1, DX, D2 and D2X. This module supports autoprobe and multiple cards. - Power management is _not_ supported. - Module snd-vx222 ---------------- diff --git a/sound/pci/Kconfig b/sound/pci/Kconfig index f7d95b224a9..31f52d3fc21 100644 --- a/sound/pci/Kconfig +++ b/sound/pci/Kconfig @@ -845,7 +845,7 @@ config SND_VIRTUOSO select SND_OXYGEN_LIB help Say Y here to include support for sound cards based on the - Asus AV100/AV200 chips, i.e., Xonar D2, DX and D2X. + Asus AV100/AV200 chips, i.e., Xonar D1, DX, D2 and D2X. To compile this driver as a module, choose M here: the module will be called snd-virtuoso. diff --git a/sound/pci/oxygen/virtuoso.c b/sound/pci/oxygen/virtuoso.c index 9a2c16bf94e..01d7b75f918 100644 --- a/sound/pci/oxygen/virtuoso.c +++ b/sound/pci/oxygen/virtuoso.c @@ -36,15 +36,15 @@ */ /* - * Xonar DX - * -------- + * Xonar D1/DX + * ----------- * * CMI8788: * * I²C <-> CS4398 (front) * <-> CS4362A (surround, center/LFE, back) * - * GPI 0 <- external power present + * GPI 0 <- external power present (DX only) * * GPIO 0 -> enable output to speakers * GPIO 1 -> enable front panel I/O @@ -96,6 +96,7 @@ MODULE_PARM_DESC(enable, "enable card"); enum { MODEL_D2, MODEL_D2X, + MODEL_D1, MODEL_DX, }; @@ -103,6 +104,7 @@ static struct pci_device_id xonar_ids[] __devinitdata = { { OXYGEN_PCI_SUBID(0x1043, 0x8269), .driver_data = MODEL_D2 }, { OXYGEN_PCI_SUBID(0x1043, 0x8275), .driver_data = MODEL_DX }, { OXYGEN_PCI_SUBID(0x1043, 0x82b7), .driver_data = MODEL_D2X }, + { OXYGEN_PCI_SUBID(0x1043, 0x834f), .driver_data = MODEL_D1 }, { } }; MODULE_DEVICE_TABLE(pci, xonar_ids); @@ -313,15 +315,12 @@ static void cs43xx_init(struct oxygen *chip) cs4362a_write(chip, 0x01, CS4362A_CPEN); } -static void xonar_dx_init(struct oxygen *chip) +static void xonar_d1_init(struct oxygen *chip) { struct xonar_data *data = chip->model_data; data->anti_pop_delay = 800; data->output_enable_bit = GPIO_DX_OUTPUT_ENABLE; - data->ext_power_reg = OXYGEN_GPI_DATA; - data->ext_power_int_reg = OXYGEN_GPI_INTERRUPT_MASK; - data->ext_power_bit = GPI_DX_EXT_POWER; data->cs4398_fm = CS4398_FM_SINGLE | CS4398_DEM_NONE | CS4398_DIF_LJUST; data->cs4362a_fm = CS4362A_FM_SINGLE | CS4362A_ATAPI_B_R | CS4362A_ATAPI_A_L; @@ -345,6 +344,16 @@ static void xonar_dx_init(struct oxygen *chip) snd_component_add(chip->card, "CS5361"); } +static void xonar_dx_init(struct oxygen *chip) +{ + struct xonar_data *data = chip->model_data; + + data->ext_power_reg = OXYGEN_GPI_DATA; + data->ext_power_int_reg = OXYGEN_GPI_INTERRUPT_MASK; + data->ext_power_bit = GPI_DX_EXT_POWER; + xonar_d1_init(chip); +} + static void xonar_cleanup(struct oxygen *chip) { struct xonar_data *data = chip->model_data; @@ -352,7 +361,7 @@ static void xonar_cleanup(struct oxygen *chip) oxygen_clear_bits16(chip, OXYGEN_GPIO_DATA, data->output_enable_bit); } -static void xonar_dx_cleanup(struct oxygen *chip) +static void xonar_d1_cleanup(struct oxygen *chip) { xonar_cleanup(chip); cs4362a_write(chip, 0x01, CS4362A_PDN | CS4362A_CPEN); @@ -365,7 +374,7 @@ static void xonar_d2_resume(struct oxygen *chip) xonar_enable_output(chip); } -static void xonar_dx_resume(struct oxygen *chip) +static void xonar_d1_resume(struct oxygen *chip) { cs43xx_init(chip); xonar_enable_output(chip); @@ -513,7 +522,7 @@ static const struct snd_kcontrol_new front_panel_switch = { .put = front_panel_put, }; -static void xonar_dx_ac97_switch(struct oxygen *chip, +static void xonar_d1_ac97_switch(struct oxygen *chip, unsigned int reg, unsigned int mute) { if (reg == AC97_LINE) { @@ -536,7 +545,7 @@ static int xonar_d2_control_filter(struct snd_kcontrol_new *template) return 0; } -static int xonar_dx_control_filter(struct snd_kcontrol_new *template) +static int xonar_d1_control_filter(struct snd_kcontrol_new *template) { if (!strncmp(template->name, "CD Capture ", 11)) return 1; /* no CD input */ @@ -548,7 +557,7 @@ static int xonar_mixer_init(struct oxygen *chip) return snd_ctl_add(chip->card, snd_ctl_new1(&alt_switch, chip)); } -static int xonar_dx_mixer_init(struct oxygen *chip) +static int xonar_d1_mixer_init(struct oxygen *chip) { return snd_ctl_add(chip->card, snd_ctl_new1(&front_panel_switch, chip)); } @@ -615,23 +624,51 @@ static const struct oxygen_model xonar_models[] = { .dac_i2s_format = OXYGEN_I2S_FORMAT_LJUST, .adc_i2s_format = OXYGEN_I2S_FORMAT_LJUST, }, + [MODEL_D1] = { + .shortname = "Xonar D1", + .longname = "Asus Virtuoso 100", + .chip = "AV200", + .owner = THIS_MODULE, + .init = xonar_d1_init, + .control_filter = xonar_d1_control_filter, + .mixer_init = xonar_d1_mixer_init, + .cleanup = xonar_d1_cleanup, + .suspend = xonar_d1_cleanup, + .resume = xonar_d1_resume, + .set_dac_params = set_cs43xx_params, + .set_adc_params = set_cs53x1_params, + .update_dac_volume = update_cs43xx_volume, + .update_dac_mute = update_cs43xx_mute, + .ac97_switch = xonar_d1_ac97_switch, + .dac_tlv = cs4362a_db_scale, + .model_data_size = sizeof(struct xonar_data), + .pcm_dev_cfg = PLAYBACK_0_TO_I2S | + PLAYBACK_1_TO_SPDIF | + CAPTURE_0_FROM_I2S_2, + .dac_channels = 8, + .dac_volume_min = 0, + .dac_volume_max = 127, + .function_flags = OXYGEN_FUNCTION_2WIRE, + .dac_i2s_format = OXYGEN_I2S_FORMAT_LJUST, + .adc_i2s_format = OXYGEN_I2S_FORMAT_LJUST, + }, [MODEL_DX] = { .shortname = "Xonar DX", .longname = "Asus Virtuoso 100", .chip = "AV200", .owner = THIS_MODULE, .init = xonar_dx_init, - .control_filter = xonar_dx_control_filter, - .mixer_init = xonar_dx_mixer_init, - .cleanup = xonar_dx_cleanup, - .suspend = xonar_dx_cleanup, - .resume = xonar_dx_resume, + .control_filter = xonar_d1_control_filter, + .mixer_init = xonar_d1_mixer_init, + .cleanup = xonar_d1_cleanup, + .suspend = xonar_d1_cleanup, + .resume = xonar_d1_resume, .set_dac_params = set_cs43xx_params, .set_adc_params = set_cs53x1_params, .update_dac_volume = update_cs43xx_volume, .update_dac_mute = update_cs43xx_mute, .gpio_changed = xonar_gpio_changed, - .ac97_switch = xonar_dx_ac97_switch, + .ac97_switch = xonar_d1_ac97_switch, .dac_tlv = cs4362a_db_scale, .model_data_size = sizeof(struct xonar_data), .pcm_dev_cfg = PLAYBACK_0_TO_I2S | -- GitLab From 1a3c4bc61547e5a75fd3b85b425624756da4cffb Mon Sep 17 00:00:00 2001 From: roel kluin Date: Thu, 7 Aug 2008 12:24:42 -0400 Subject: [PATCH 364/750] atl1e: WAKE_MCAST 2x. 1st WAKE_UCAST? Signed-off-by: Jeff Garzik --- drivers/net/atl1e/atl1e_ethtool.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/atl1e/atl1e_ethtool.c b/drivers/net/atl1e/atl1e_ethtool.c index cdc3b85b10b..619c6583e1a 100644 --- a/drivers/net/atl1e/atl1e_ethtool.c +++ b/drivers/net/atl1e/atl1e_ethtool.c @@ -355,7 +355,7 @@ static int atl1e_set_wol(struct net_device *netdev, struct ethtool_wolinfo *wol) struct atl1e_adapter *adapter = netdev_priv(netdev); if (wol->wolopts & (WAKE_ARP | WAKE_MAGICSECURE | - WAKE_MCAST | WAKE_BCAST | WAKE_MCAST)) + WAKE_UCAST | WAKE_MCAST | WAKE_BCAST)) return -EOPNOTSUPP; /* these settings will always override what we currently have */ adapter->wol = 0; -- GitLab From c0912585ec8b64d846d56995241f2c8a7f48ee75 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Thu, 7 Aug 2008 17:21:09 +0100 Subject: [PATCH 365/750] AX88796: Fix locking in ethtool support Fix a pair of nasty locking problems in the ax88796 driver spotted by a sparse check: warning: context imbalance in 'ax_get_settings' - wrong count at exit warning: context imbalance in 'ax_set_settings' - wrong count at exit Signed-off-by: Ben Dooks Signed-off-by: Jeff Garzik --- drivers/net/ax88796.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/ax88796.c b/drivers/net/ax88796.c index 0b4adf4a0f7..a886a4b9f7e 100644 --- a/drivers/net/ax88796.c +++ b/drivers/net/ax88796.c @@ -554,7 +554,7 @@ static int ax_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) spin_lock_irqsave(&ax->mii_lock, flags); mii_ethtool_gset(&ax->mii, cmd); - spin_lock_irqsave(&ax->mii_lock, flags); + spin_unlock_irqrestore(&ax->mii_lock, flags); return 0; } @@ -567,7 +567,7 @@ static int ax_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) spin_lock_irqsave(&ax->mii_lock, flags); rc = mii_ethtool_sset(&ax->mii, cmd); - spin_lock_irqsave(&ax->mii_lock, flags); + spin_unlock_irqrestore(&ax->mii_lock, flags); return rc; } -- GitLab From f2b6079464fc73cf12f08248180a618f05033a70 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Thu, 14 Aug 2008 01:45:41 -0700 Subject: [PATCH 366/750] sparc64: Fix cmdline_memory_size handling bugs. First, lmb_enforce_memory_limit() interprets it's argument (mostly, heh) as a size limit not an address limit. So pass the raw cmdline_memory_size value into it. And we don't need to check it against zero, lmb_enforce_memory_limit() does that for us. Next, free_initmem() needs special handling when the kernel command line trims the available memory. The problem case is if the trimmed out memory is where the kernel image itself resides. When that memory is trimmed out, we don't add those physical ram areas to the sparsemem active ranges, amongst other things. Which means that this free_initmem() code will free up invalid page structs, resulting in either crashes or hangs. Just quick fix this by not freeing initmem at all if "mem=" was given on the boot command line. Signed-off-by: David S. Miller --- arch/sparc64/mm/init.c | 27 +++++++++++++++++++-------- 1 file changed, 19 insertions(+), 8 deletions(-) diff --git a/arch/sparc64/mm/init.c b/arch/sparc64/mm/init.c index 64d8e7623e0..b4aeb0f696d 100644 --- a/arch/sparc64/mm/init.c +++ b/arch/sparc64/mm/init.c @@ -1726,8 +1726,7 @@ void __init paging_init(void) find_ramdisk(phys_base); - if (cmdline_memory_size) - lmb_enforce_memory_limit(phys_base + cmdline_memory_size); + lmb_enforce_memory_limit(cmdline_memory_size); lmb_analyze(); lmb_dump_all(); @@ -1964,6 +1963,15 @@ void __init mem_init(void) void free_initmem(void) { unsigned long addr, initend; + int do_free = 1; + + /* If the physical memory maps were trimmed by kernel command + * line options, don't even try freeing this initmem stuff up. + * The kernel image could have been in the trimmed out region + * and if so the freeing below will free invalid page structs. + */ + if (cmdline_memory_size) + do_free = 0; /* * The init section is aligned to 8k in vmlinux.lds. Page align for >8k pagesizes. @@ -1978,13 +1986,16 @@ void free_initmem(void) ((unsigned long) __va(kern_base)) - ((unsigned long) KERNBASE)); memset((void *)addr, POISON_FREE_INITMEM, PAGE_SIZE); - p = virt_to_page(page); - ClearPageReserved(p); - init_page_count(p); - __free_page(p); - num_physpages++; - totalram_pages++; + if (do_free) { + p = virt_to_page(page); + + ClearPageReserved(p); + init_page_count(p); + __free_page(p); + num_physpages++; + totalram_pages++; + } } } -- GitLab From 09f2724a786f76475ef2985cf84f5359c553aade Mon Sep 17 00:00:00 2001 From: "Zhang, Yanmin" Date: Wed, 14 Aug 2030 15:56:40 +0800 Subject: [PATCH 367/750] sched: fix the race between walk_tg_tree and sched_create_group With 2.6.27-rc3, I hit a kernel panic when running volanoMark on my new x86_64 machine. I also hit it with other 2.6.27-rc kernels. See below log. Basically, function walk_tg_tree and sched_create_group have a race between accessing and initiating tg->children. Below patch fixes it by moving tg->children initiation to the front of linking tg->siblings to parent->children. {----------------panic log------------} BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 IP: [] walk_tg_tree+0x45/0x7f PGD 1be1c4067 PUD 1bdd8d067 PMD 0 Oops: 0000 [1] SMP CPU 11 Modules linked in: igb Pid: 22979, comm: java Not tainted 2.6.27-rc3 #1 RIP: 0010:[] [] walk_tg_tree+0x45/0x7f RSP: 0018:ffff8801bfbbbd18 EFLAGS: 00010083 RAX: 0000000000000000 RBX: ffff8800be0dce40 RCX: ffffffffffffffc0 RDX: ffff880102c43740 RSI: 0000000000000000 RDI: ffff8800be0dce40 RBP: ffff8801bfbbbd48 R08: ffff8800ba437bc8 R09: 0000000000001f40 R10: ffff8801be812100 R11: ffffffff805fdf44 R12: ffff880102c43740 R13: 0000000000000000 R14: ffffffff8022cf0f R15: ffffffff8022749f FS: 00000000568ac950(0063) GS:ffff8801bfa26d00(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 0000000000000000 CR3: 00000001bd848000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process java (pid: 22979, threadinfo ffff8801b145a000, task ffff8801bf18e450) Stack: 0000000000000001 ffff8800ba5c8d60 0000000000000001 0000000000000001 ffff8800bad1ccb8 0000000000000000 ffff8801bfbbbd98 ffffffff8022ed37 0000000000000001 0000000000000286 ffff8801bd5ee180 ffff8800ba437bc8 Call Trace: [] try_to_wake_up+0x71/0x24c [] autoremove_wake_function+0x9/0x2e [] ? __wake_up_common+0x46/0x76 [] __wake_up+0x38/0x4f [] tcp_v4_rcv+0x380/0x62e Signed-off-by: Zhang Yanmin Acked-by: Peter Zijlstra Signed-off-by: Ingo Molnar --- kernel/sched.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/sched.c b/kernel/sched.c index d601fb0406c..8bf8a5528bc 100644 --- a/kernel/sched.c +++ b/kernel/sched.c @@ -8462,8 +8462,8 @@ struct task_group *sched_create_group(struct task_group *parent) WARN_ON(!parent); /* root should already exist */ tg->parent = parent; - list_add_rcu(&tg->siblings, &parent->children); INIT_LIST_HEAD(&tg->children); + list_add_rcu(&tg->siblings, &parent->children); spin_unlock_irqrestore(&task_group_lock, flags); return tg; -- GitLab From 23b49c19f6946cc33392a1fc75dd788dd4a90fb7 Mon Sep 17 00:00:00 2001 From: Max Krasnyansky Date: Mon, 11 Aug 2008 14:55:31 -0700 Subject: [PATCH 368/750] x86: resurrect proper handling of maxcpus= kernel option (v2) For some reason we had two parsers registered for maxcpus=. One in init/main.c and another in arch/x86/smpboot.c. So I nuked the one in arch/x86. Also 64-bit kernels used to handle maxcpus= as documented in Documentation/cpu-hotplug.txt. CPUs with 'id > maxcpus' are initialized but not booted. 32-bit version for some reason ignored them even though all the infrastructure for booting them later is there. In the current mainline both 64 and 32 bit versions are broken. This patch restores the correct behaviour. I've tested x86_64 version on 4- and 8- way Core2 and 2-way Opteron based machines. Various config combinations SMP, !SMP, CPU_HOTPLUG, !CPU_HOTPLUG. Booted with maxcpus=1 and maxcpus=4, etc. Everything is working as expected. So far we've received two reports from different people confirming that 32-bit version also works fine, both on dual core laptops and 16way server machines. [v2: This version fixes visws breakage pointed out by Ingo.] Signed-off-by: Max Krasnyansky Cc: lizf@cn.fujitsu.com Cc: jeff.chua.linux@gmail.com Signed-off-by: Ingo Molnar --- arch/x86/kernel/apic_32.c | 8 -------- arch/x86/kernel/apic_64.c | 7 ------- arch/x86/kernel/smpboot.c | 14 -------------- arch/x86/kernel/visws_quirks.c | 6 ++---- 4 files changed, 2 insertions(+), 33 deletions(-) diff --git a/arch/x86/kernel/apic_32.c b/arch/x86/kernel/apic_32.c index 039a8d4aaf6..f88bd0d982b 100644 --- a/arch/x86/kernel/apic_32.c +++ b/arch/x86/kernel/apic_32.c @@ -1454,8 +1454,6 @@ void disconnect_bsp_APIC(int virt_wire_setup) } } -unsigned int __cpuinitdata maxcpus = NR_CPUS; - void __cpuinit generic_processor_info(int apicid, int version) { int cpu; @@ -1482,12 +1480,6 @@ void __cpuinit generic_processor_info(int apicid, int version) return; } - if (num_processors >= maxcpus) { - printk(KERN_WARNING "WARNING: maxcpus limit of %i reached." - " Processor ignored.\n", maxcpus); - return; - } - num_processors++; cpus_complement(tmp_map, cpu_present_map); cpu = first_cpu(tmp_map); diff --git a/arch/x86/kernel/apic_64.c b/arch/x86/kernel/apic_64.c index 7f1f030da7e..446c062e831 100644 --- a/arch/x86/kernel/apic_64.c +++ b/arch/x86/kernel/apic_64.c @@ -90,7 +90,6 @@ static unsigned long apic_phys; unsigned long mp_lapic_addr; -unsigned int __cpuinitdata maxcpus = NR_CPUS; /* * Get the LAPIC version */ @@ -1062,12 +1061,6 @@ void __cpuinit generic_processor_info(int apicid, int version) return; } - if (num_processors >= maxcpus) { - printk(KERN_WARNING "WARNING: maxcpus limit of %i reached." - " Processor ignored.\n", maxcpus); - return; - } - num_processors++; cpus_complement(tmp_map, cpu_present_map); cpu = first_cpu(tmp_map); diff --git a/arch/x86/kernel/smpboot.c b/arch/x86/kernel/smpboot.c index 91055d7fc1b..e25287e4a85 100644 --- a/arch/x86/kernel/smpboot.c +++ b/arch/x86/kernel/smpboot.c @@ -1386,17 +1386,3 @@ void __cpu_die(unsigned int cpu) BUG(); } #endif - -/* - * If the BIOS enumerates physical processors before logical, - * maxcpus=N at enumeration-time can be used to disable HT. - */ -static int __init parse_maxcpus(char *arg) -{ - extern unsigned int maxcpus; - - if (arg) - maxcpus = simple_strtoul(arg, NULL, 0); - return 0; -} -early_param("maxcpus", parse_maxcpus); diff --git a/arch/x86/kernel/visws_quirks.c b/arch/x86/kernel/visws_quirks.c index 41e01b145c4..594ef47f0a6 100644 --- a/arch/x86/kernel/visws_quirks.c +++ b/arch/x86/kernel/visws_quirks.c @@ -184,8 +184,6 @@ static int __init visws_get_smp_config(unsigned int early) return 1; } -extern unsigned int __cpuinitdata maxcpus; - /* * The Visual Workstation is Intel MP compliant in the hardware * sense, but it doesn't have a BIOS(-configuration table). @@ -244,8 +242,8 @@ static int __init visws_find_smp_config(unsigned int reserve) ncpus = CO_CPU_MAX; } - if (ncpus > maxcpus) - ncpus = maxcpus; + if (ncpus > setup_max_cpus) + ncpus = setup_max_cpus; #ifdef CONFIG_X86_LOCAL_APIC smp_found_config = 1; -- GitLab From 858f774733b72609acb28104475f131abb912c08 Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Thu, 14 Aug 2008 02:16:29 -0700 Subject: [PATCH 369/750] x86: don't call e820_regiter_active_regions if out of range on node so we don't get warning on 32bit system with 64g RAM or more Signed-off-by: Yinghai Lu Signed-off-by: Ingo Molnar --- arch/x86/mm/srat_32.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) diff --git a/arch/x86/mm/srat_32.c b/arch/x86/mm/srat_32.c index 1eb2973a301..16ae70fc57e 100644 --- a/arch/x86/mm/srat_32.c +++ b/arch/x86/mm/srat_32.c @@ -178,7 +178,7 @@ void acpi_numa_arch_fixup(void) * start of the node, and that the current "end" address is after * the previous one. */ -static __init void node_read_chunk(int nid, struct node_memory_chunk_s *memory_chunk) +static __init int node_read_chunk(int nid, struct node_memory_chunk_s *memory_chunk) { /* * Only add present memory as told by the e820. @@ -189,10 +189,10 @@ static __init void node_read_chunk(int nid, struct node_memory_chunk_s *memory_c if (memory_chunk->start_pfn >= max_pfn) { printk(KERN_INFO "Ignoring SRAT pfns: %08lx - %08lx\n", memory_chunk->start_pfn, memory_chunk->end_pfn); - return; + return -1; } if (memory_chunk->nid != nid) - return; + return -1; if (!node_has_online_mem(nid)) node_start_pfn[nid] = memory_chunk->start_pfn; @@ -202,6 +202,8 @@ static __init void node_read_chunk(int nid, struct node_memory_chunk_s *memory_c if (node_end_pfn[nid] < memory_chunk->end_pfn) node_end_pfn[nid] = memory_chunk->end_pfn; + + return 0; } int __init get_memcfg_from_srat(void) @@ -259,7 +261,9 @@ int __init get_memcfg_from_srat(void) printk(KERN_DEBUG "chunk %d nid %d start_pfn %08lx end_pfn %08lx\n", j, chunk->nid, chunk->start_pfn, chunk->end_pfn); - node_read_chunk(chunk->nid, chunk); + if (node_read_chunk(chunk->nid, chunk)) + continue; + e820_register_active_regions(chunk->nid, chunk->start_pfn, min(chunk->end_pfn, max_pfn)); } -- GitLab From a58f03b07539f6575adaa011712fa139c9343742 Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Thu, 14 Aug 2008 02:16:30 -0700 Subject: [PATCH 370/750] x86: check bigsmp in smp_sanity_check instead of cpu_up clear bits for cpu nr > 8. This allows us to boot the full range of possible CPUs that the supported APIC model will allow. Previously we'd hang or boot up with less than 8 CPUs. Signed-off-by: Yinghai Lu Tested-by: Jeff Chua Signed-off-by: Ingo Molnar --- arch/x86/kernel/smpboot.c | 38 ++++++++++++++++++++++++++++---------- 1 file changed, 28 insertions(+), 10 deletions(-) diff --git a/arch/x86/kernel/smpboot.c b/arch/x86/kernel/smpboot.c index e25287e4a85..a8fb8a980fa 100644 --- a/arch/x86/kernel/smpboot.c +++ b/arch/x86/kernel/smpboot.c @@ -994,17 +994,7 @@ int __cpuinit native_cpu_up(unsigned int cpu) flush_tlb_all(); low_mappings = 1; -#ifdef CONFIG_X86_PC - if (def_to_bigsmp && apicid > 8) { - printk(KERN_WARNING - "More than 8 CPUs detected - skipping them.\n" - "Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.\n"); - err = -1; - } else - err = do_boot_cpu(apicid, cpu); -#else err = do_boot_cpu(apicid, cpu); -#endif zap_low_mappings(); low_mappings = 0; @@ -1058,6 +1048,34 @@ static __init void disable_smp(void) static int __init smp_sanity_check(unsigned max_cpus) { preempt_disable(); + +#if defined(CONFIG_X86_PC) && defined(CONFIG_X86_32) + if (def_to_bigsmp && nr_cpu_ids > 8) { + unsigned int cpu; + unsigned nr; + + printk(KERN_WARNING + "More than 8 CPUs detected - skipping them.\n" + "Use CONFIG_X86_GENERICARCH and CONFIG_X86_BIGSMP.\n"); + + nr = 0; + for_each_present_cpu(cpu) { + if (nr >= 8) + cpu_clear(cpu, cpu_present_map); + nr++; + } + + nr = 0; + for_each_possible_cpu(cpu) { + if (nr >= 8) + cpu_clear(cpu, cpu_possible_map); + nr++; + } + + nr_cpu_ids = 8; + } +#endif + if (!physid_isset(hard_smp_processor_id(), phys_cpu_present_map)) { printk(KERN_WARNING "weird, boot CPU (#%d) not listed" "by the BIOS.\n", hard_smp_processor_id()); -- GitLab From c78c7e35a4709b55d3126624662c8f6d7e3d1a5e Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Tue, 12 Aug 2008 16:30:12 +0300 Subject: [PATCH 371/750] UBIFS: xattr bugfixes Xattr code has not been tested for a while and there were serveral bugs. One of them is using wrong inode in 'ubifs_jnl_change_xattr()'. The other is a deadlock in 'ubifs_setxattr()': the i_mutex is locked in 'cap_inode_need_killpriv()' path, so deadlock happens when 'ubifs_setxattr()' tries to lock it again. Thanks to Zoltan Sogor for finding these bugs. Signed-off-by: Artem Bityutskiy --- fs/ubifs/journal.c | 2 +- fs/ubifs/xattr.c | 44 +++++++++++++++++--------------------------- 2 files changed, 18 insertions(+), 28 deletions(-) diff --git a/fs/ubifs/journal.c b/fs/ubifs/journal.c index acdae00aaa5..22993f867d1 100644 --- a/fs/ubifs/journal.c +++ b/fs/ubifs/journal.c @@ -1374,7 +1374,7 @@ int ubifs_jnl_change_xattr(struct ubifs_info *c, const struct inode *inode, const struct inode *host) { int err, len1, len2, aligned_len, aligned_len1, lnum, offs; - struct ubifs_inode *host_ui = ubifs_inode(inode); + struct ubifs_inode *host_ui = ubifs_inode(host); struct ubifs_ino_node *ino; union ubifs_key key; int sync = IS_DIRSYNC(host); diff --git a/fs/ubifs/xattr.c b/fs/ubifs/xattr.c index 6f493dea561..649bec78b64 100644 --- a/fs/ubifs/xattr.c +++ b/fs/ubifs/xattr.c @@ -61,7 +61,7 @@ /* * Limit the number of extended attributes per inode so that the total size - * (xattr_size) is guaranteeded to fit in an 'unsigned int'. + * (@xattr_size) is guaranteeded to fit in an 'unsigned int'. */ #define MAX_XATTRS_PER_INODE 65535 @@ -110,7 +110,7 @@ static int create_xattr(struct ubifs_info *c, struct inode *host, return -ENOSPC; /* * Linux limits the maximum size of the extended attribute names list - * to %XATTR_LIST_MAX. This means we should not allow creating more* + * to %XATTR_LIST_MAX. This means we should not allow creating more * extended attributes if the name list becomes larger. This limitation * is artificial for UBIFS, though. */ @@ -128,7 +128,6 @@ static int create_xattr(struct ubifs_info *c, struct inode *host, goto out_budg; } - mutex_lock(&host_ui->ui_mutex); /* Re-define all operations to be "nothing" */ inode->i_mapping->a_ops = &none_address_operations; inode->i_op = &none_inode_operations; @@ -141,23 +140,19 @@ static int create_xattr(struct ubifs_info *c, struct inode *host, ui->data = kmalloc(size, GFP_NOFS); if (!ui->data) { err = -ENOMEM; - goto out_unlock; + goto out_free; } - memcpy(ui->data, value, size); + inode->i_size = ui->ui_size = size; + ui->data_len = size; + + mutex_lock(&host_ui->ui_mutex); host->i_ctime = ubifs_current_time(host); host_ui->xattr_cnt += 1; host_ui->xattr_size += CALC_DENT_SIZE(nm->len); host_ui->xattr_size += CALC_XATTR_BYTES(size); host_ui->xattr_names += nm->len; - /* - * We do not use i_size_write() because nobody can race with us as we - * are holding host @host->i_mutex - every xattr operation for this - * inode is serialized by it. - */ - inode->i_size = ui->ui_size = size; - ui->data_len = size; err = ubifs_jnl_update(c, host, nm, inode, 0, 1); if (err) goto out_cancel; @@ -172,8 +167,8 @@ out_cancel: host_ui->xattr_cnt -= 1; host_ui->xattr_size -= CALC_DENT_SIZE(nm->len); host_ui->xattr_size -= CALC_XATTR_BYTES(size); -out_unlock: mutex_unlock(&host_ui->ui_mutex); +out_free: make_bad_inode(inode); iput(inode); out_budg: @@ -207,22 +202,21 @@ static int change_xattr(struct ubifs_info *c, struct inode *host, if (err) return err; - mutex_lock(&host_ui->ui_mutex); - host->i_ctime = ubifs_current_time(host); - host_ui->xattr_size -= CALC_XATTR_BYTES(ui->data_len); - host_ui->xattr_size += CALC_XATTR_BYTES(size); - kfree(ui->data); ui->data = kmalloc(size, GFP_NOFS); if (!ui->data) { err = -ENOMEM; - goto out_unlock; + goto out_free; } - memcpy(ui->data, value, size); inode->i_size = ui->ui_size = size; ui->data_len = size; + mutex_lock(&host_ui->ui_mutex); + host->i_ctime = ubifs_current_time(host); + host_ui->xattr_size -= CALC_XATTR_BYTES(ui->data_len); + host_ui->xattr_size += CALC_XATTR_BYTES(size); + /* * It is important to write the host inode after the xattr inode * because if the host inode gets synchronized (via 'fsync()'), then @@ -240,9 +234,9 @@ static int change_xattr(struct ubifs_info *c, struct inode *host, out_cancel: host_ui->xattr_size -= CALC_XATTR_BYTES(size); host_ui->xattr_size += CALC_XATTR_BYTES(ui->data_len); - make_bad_inode(inode); -out_unlock: mutex_unlock(&host_ui->ui_mutex); + make_bad_inode(inode); +out_free: ubifs_release_budget(c, &req); return err; } @@ -312,6 +306,7 @@ int ubifs_setxattr(struct dentry *dentry, const char *name, dbg_gen("xattr '%s', host ino %lu ('%.*s'), size %zd", name, host->i_ino, dentry->d_name.len, dentry->d_name.name, size); + ubifs_assert(mutex_is_locked(&host->i_mutex)); if (size > UBIFS_MAX_INO_DATA) return -ERANGE; @@ -384,7 +379,6 @@ ssize_t ubifs_getxattr(struct dentry *dentry, const char *name, void *buf, if (!xent) return -ENOMEM; - mutex_lock(&host->i_mutex); xent_key_init(c, &key, host->i_ino, &nm); err = ubifs_tnc_lookup_nm(c, &key, xent, &nm); if (err) { @@ -419,7 +413,6 @@ ssize_t ubifs_getxattr(struct dentry *dentry, const char *name, void *buf, out_iput: iput(inode); out_unlock: - mutex_unlock(&host->i_mutex); kfree(xent); return err; } @@ -449,8 +442,6 @@ ssize_t ubifs_listxattr(struct dentry *dentry, char *buffer, size_t size) return -ERANGE; lowest_xent_key(c, &key, host->i_ino); - - mutex_lock(&host->i_mutex); while (1) { int type; @@ -479,7 +470,6 @@ ssize_t ubifs_listxattr(struct dentry *dentry, char *buffer, size_t size) pxent = xent; key_read(c, &xent->key, &key); } - mutex_unlock(&host->i_mutex); kfree(pxent); if (err != -ENOENT) { -- GitLab From a6825f1c1fa83b1e92b6715ee5771a4d6524d3b9 Mon Sep 17 00:00:00 2001 From: Thomas Gleixner Date: Thu, 14 Aug 2008 12:17:06 +0200 Subject: [PATCH 372/750] x86: hpet: workaround SB700 BIOS AMD SB700 based systems with spread spectrum enabled use a SMM based HPET emulation to provide proper frequency setting. The SMM code is initialized with the first HPET register access and takes some time to complete. During this time the config register reads 0xffffffff. We check for max. 1000 loops whether the config register reads a non 0xffffffff value to make sure that HPET is up and running before we go further. A counting loop is safe, as the HPET access takes thousands of CPU cycles. On non SB700 based machines this check is only done once and has no side effects. Based on a quirk patch from: crane cai Signed-off-by: Thomas Gleixner --- arch/x86/kernel/hpet.c | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/arch/x86/kernel/hpet.c b/arch/x86/kernel/hpet.c index ad2b15a1334..59fd3b6b130 100644 --- a/arch/x86/kernel/hpet.c +++ b/arch/x86/kernel/hpet.c @@ -359,6 +359,7 @@ static int hpet_clocksource_register(void) int __init hpet_enable(void) { unsigned long id; + int i; if (!is_hpet_capable()) return 0; @@ -369,6 +370,29 @@ int __init hpet_enable(void) * Read the period and check for a sane value: */ hpet_period = hpet_readl(HPET_PERIOD); + + /* + * AMD SB700 based systems with spread spectrum enabled use a + * SMM based HPET emulation to provide proper frequency + * setting. The SMM code is initialized with the first HPET + * register access and takes some time to complete. During + * this time the config register reads 0xffffffff. We check + * for max. 1000 loops whether the config register reads a non + * 0xffffffff value to make sure that HPET is up and running + * before we go further. A counting loop is safe, as the HPET + * access takes thousands of CPU cycles. On non SB700 based + * machines this check is only done once and has no side + * effects. + */ + for (i = 0; hpet_readl(HPET_CFG) == 0xFFFFFFFF; i++) { + if (i == 1000) { + printk(KERN_WARNING + "HPET config register value = 0xFFFFFFFF. " + "Disabling HPET\n"); + goto out_nohpet; + } + } + if (hpet_period < HPET_MIN_PERIOD || hpet_period > HPET_MAX_PERIOD) goto out_nohpet; -- GitLab From 5cd9c58fbe9ec92b45b27e131719af4f2bd9eb40 Mon Sep 17 00:00:00 2001 From: David Howells Date: Thu, 14 Aug 2008 11:37:28 +0100 Subject: [PATCH 373/750] security: Fix setting of PF_SUPERPRIV by __capable() Fix the setting of PF_SUPERPRIV by __capable() as it could corrupt the flags the target process if that is not the current process and it is trying to change its own flags in a different way at the same time. __capable() is using neither atomic ops nor locking to protect t->flags. This patch removes __capable() and introduces has_capability() that doesn't set PF_SUPERPRIV on the process being queried. This patch further splits security_ptrace() in two: (1) security_ptrace_may_access(). This passes judgement on whether one process may access another only (PTRACE_MODE_ATTACH for ptrace() and PTRACE_MODE_READ for /proc), and takes a pointer to the child process. current is the parent. (2) security_ptrace_traceme(). This passes judgement on PTRACE_TRACEME only, and takes only a pointer to the parent process. current is the child. In Smack and commoncap, this uses has_capability() to determine whether the parent will be permitted to use PTRACE_ATTACH if normal checks fail. This does not set PF_SUPERPRIV. Two of the instances of __capable() actually only act on current, and so have been changed to calls to capable(). Of the places that were using __capable(): (1) The OOM killer calls __capable() thrice when weighing the killability of a process. All of these now use has_capability(). (2) cap_ptrace() and smack_ptrace() were using __capable() to check to see whether the parent was allowed to trace any process. As mentioned above, these have been split. For PTRACE_ATTACH and /proc, capable() is now used, and for PTRACE_TRACEME, has_capability() is used. (3) cap_safe_nice() only ever saw current, so now uses capable(). (4) smack_setprocattr() rejected accesses to tasks other than current just after calling __capable(), so the order of these two tests have been switched and capable() is used instead. (5) In smack_file_send_sigiotask(), we need to allow privileged processes to receive SIGIO on files they're manipulating. (6) In smack_task_wait(), we let a process wait for a privileged process, whether or not the process doing the waiting is privileged. I've tested this with the LTP SELinux and syscalls testscripts. Signed-off-by: David Howells Acked-by: Serge Hallyn Acked-by: Casey Schaufler Acked-by: Andrew G. Morgan Acked-by: Al Viro Signed-off-by: James Morris --- include/linux/capability.h | 15 ++++++++++-- include/linux/security.h | 39 +++++++++++++++++++----------- kernel/capability.c | 21 +++++++++------- kernel/ptrace.c | 5 ++-- mm/oom_kill.c | 6 +++-- security/capability.c | 3 ++- security/commoncap.c | 24 +++++++++++++------ security/root_plug.c | 3 ++- security/security.c | 10 +++++--- security/selinux/hooks.c | 25 +++++++++++++------ security/smack/smack_lsm.c | 49 ++++++++++++++++++++++++++------------ 11 files changed, 137 insertions(+), 63 deletions(-) diff --git a/include/linux/capability.h b/include/linux/capability.h index 02673846d20..9d1fe30b6f6 100644 --- a/include/linux/capability.h +++ b/include/linux/capability.h @@ -503,8 +503,19 @@ extern const kernel_cap_t __cap_init_eff_set; kernel_cap_t cap_set_effective(const kernel_cap_t pE_new); -int capable(int cap); -int __capable(struct task_struct *t, int cap); +/** + * has_capability - Determine if a task has a superior capability available + * @t: The task in question + * @cap: The capability to be tested for + * + * Return true if the specified task has the given superior capability + * currently in effect, false if not. + * + * Note that this does not set PF_SUPERPRIV on the task. + */ +#define has_capability(t, cap) (security_capable((t), (cap)) == 0) + +extern int capable(int cap); #endif /* __KERNEL__ */ diff --git a/include/linux/security.h b/include/linux/security.h index fd96e7f8a6f..2ee5ecfb239 100644 --- a/include/linux/security.h +++ b/include/linux/security.h @@ -46,8 +46,8 @@ struct audit_krule; */ extern int cap_capable(struct task_struct *tsk, int cap); extern int cap_settime(struct timespec *ts, struct timezone *tz); -extern int cap_ptrace(struct task_struct *parent, struct task_struct *child, - unsigned int mode); +extern int cap_ptrace_may_access(struct task_struct *child, unsigned int mode); +extern int cap_ptrace_traceme(struct task_struct *parent); extern int cap_capget(struct task_struct *target, kernel_cap_t *effective, kernel_cap_t *inheritable, kernel_cap_t *permitted); extern int cap_capset_check(struct task_struct *target, kernel_cap_t *effective, kernel_cap_t *inheritable, kernel_cap_t *permitted); extern void cap_capset_set(struct task_struct *target, kernel_cap_t *effective, kernel_cap_t *inheritable, kernel_cap_t *permitted); @@ -1157,17 +1157,24 @@ static inline void security_free_mnt_opts(struct security_mnt_opts *opts) * @alter contains the flag indicating whether changes are to be made. * Return 0 if permission is granted. * - * @ptrace: - * Check permission before allowing the @parent process to trace the + * @ptrace_may_access: + * Check permission before allowing the current process to trace the * @child process. * Security modules may also want to perform a process tracing check * during an execve in the set_security or apply_creds hooks of * binprm_security_ops if the process is being traced and its security * attributes would be changed by the execve. - * @parent contains the task_struct structure for parent process. - * @child contains the task_struct structure for child process. + * @child contains the task_struct structure for the target process. * @mode contains the PTRACE_MODE flags indicating the form of access. * Return 0 if permission is granted. + * @ptrace_traceme: + * Check that the @parent process has sufficient permission to trace the + * current process before allowing the current process to present itself + * to the @parent process for tracing. + * The parent process will still have to undergo the ptrace_may_access + * checks before it is allowed to trace this one. + * @parent contains the task_struct structure for debugger process. + * Return 0 if permission is granted. * @capget: * Get the @effective, @inheritable, and @permitted capability sets for * the @target process. The hook may also perform permission checking to @@ -1287,8 +1294,8 @@ static inline void security_free_mnt_opts(struct security_mnt_opts *opts) struct security_operations { char name[SECURITY_NAME_MAX + 1]; - int (*ptrace) (struct task_struct *parent, struct task_struct *child, - unsigned int mode); + int (*ptrace_may_access) (struct task_struct *child, unsigned int mode); + int (*ptrace_traceme) (struct task_struct *parent); int (*capget) (struct task_struct *target, kernel_cap_t *effective, kernel_cap_t *inheritable, kernel_cap_t *permitted); @@ -1560,8 +1567,8 @@ extern struct dentry *securityfs_create_dir(const char *name, struct dentry *par extern void securityfs_remove(struct dentry *dentry); /* Security operations */ -int security_ptrace(struct task_struct *parent, struct task_struct *child, - unsigned int mode); +int security_ptrace_may_access(struct task_struct *child, unsigned int mode); +int security_ptrace_traceme(struct task_struct *parent); int security_capget(struct task_struct *target, kernel_cap_t *effective, kernel_cap_t *inheritable, @@ -1742,11 +1749,15 @@ static inline int security_init(void) return 0; } -static inline int security_ptrace(struct task_struct *parent, - struct task_struct *child, - unsigned int mode) +static inline int security_ptrace_may_access(struct task_struct *child, + unsigned int mode) +{ + return cap_ptrace_may_access(child, mode); +} + +static inline int security_ptrace_traceme(struct task_struct *child) { - return cap_ptrace(parent, child, mode); + return cap_ptrace_traceme(parent); } static inline int security_capget(struct task_struct *target, diff --git a/kernel/capability.c b/kernel/capability.c index 0101e847603..33e51e78c2d 100644 --- a/kernel/capability.c +++ b/kernel/capability.c @@ -486,17 +486,22 @@ asmlinkage long sys_capset(cap_user_header_t header, const cap_user_data_t data) return ret; } -int __capable(struct task_struct *t, int cap) +/** + * capable - Determine if the current task has a superior capability in effect + * @cap: The capability to be tested for + * + * Return true if the current task has the given superior capability currently + * available for use, false if not. + * + * This sets PF_SUPERPRIV on the task if the capability is available on the + * assumption that it's about to be used. + */ +int capable(int cap) { - if (security_capable(t, cap) == 0) { - t->flags |= PF_SUPERPRIV; + if (has_capability(current, cap)) { + current->flags |= PF_SUPERPRIV; return 1; } return 0; } - -int capable(int cap) -{ - return __capable(current, cap); -} EXPORT_SYMBOL(capable); diff --git a/kernel/ptrace.c b/kernel/ptrace.c index 082b3fcb32a..356699a96d5 100644 --- a/kernel/ptrace.c +++ b/kernel/ptrace.c @@ -140,7 +140,7 @@ int __ptrace_may_access(struct task_struct *task, unsigned int mode) if (!dumpable && !capable(CAP_SYS_PTRACE)) return -EPERM; - return security_ptrace(current, task, mode); + return security_ptrace_may_access(task, mode); } bool ptrace_may_access(struct task_struct *task, unsigned int mode) @@ -499,8 +499,7 @@ repeat: goto repeat; } - ret = security_ptrace(current->parent, current, - PTRACE_MODE_ATTACH); + ret = security_ptrace_traceme(current->parent); /* * Set the ptrace bit in the process ptrace flags. diff --git a/mm/oom_kill.c b/mm/oom_kill.c index 8a5467ee626..64e5b4bcd96 100644 --- a/mm/oom_kill.c +++ b/mm/oom_kill.c @@ -26,6 +26,7 @@ #include #include #include +#include int sysctl_panic_on_oom; int sysctl_oom_kill_allocating_task; @@ -128,7 +129,8 @@ unsigned long badness(struct task_struct *p, unsigned long uptime) * Superuser processes are usually more important, so we make it * less likely that we kill those. */ - if (__capable(p, CAP_SYS_ADMIN) || __capable(p, CAP_SYS_RESOURCE)) + if (has_capability(p, CAP_SYS_ADMIN) || + has_capability(p, CAP_SYS_RESOURCE)) points /= 4; /* @@ -137,7 +139,7 @@ unsigned long badness(struct task_struct *p, unsigned long uptime) * tend to only have this flag set on applications they think * of as important. */ - if (__capable(p, CAP_SYS_RAWIO)) + if (has_capability(p, CAP_SYS_RAWIO)) points /= 4; /* diff --git a/security/capability.c b/security/capability.c index 63d10da515a..24587481903 100644 --- a/security/capability.c +++ b/security/capability.c @@ -811,7 +811,8 @@ struct security_operations default_security_ops = { void security_fixup_ops(struct security_operations *ops) { - set_to_cap_if_null(ops, ptrace); + set_to_cap_if_null(ops, ptrace_may_access); + set_to_cap_if_null(ops, ptrace_traceme); set_to_cap_if_null(ops, capget); set_to_cap_if_null(ops, capset_check); set_to_cap_if_null(ops, capset_set); diff --git a/security/commoncap.c b/security/commoncap.c index 4afbece37a0..e4c4b3fc0c0 100644 --- a/security/commoncap.c +++ b/security/commoncap.c @@ -63,14 +63,24 @@ int cap_settime(struct timespec *ts, struct timezone *tz) return 0; } -int cap_ptrace (struct task_struct *parent, struct task_struct *child, - unsigned int mode) +int cap_ptrace_may_access(struct task_struct *child, unsigned int mode) { /* Derived from arch/i386/kernel/ptrace.c:sys_ptrace. */ - if (!cap_issubset(child->cap_permitted, parent->cap_permitted) && - !__capable(parent, CAP_SYS_PTRACE)) - return -EPERM; - return 0; + if (cap_issubset(child->cap_permitted, current->cap_permitted)) + return 0; + if (capable(CAP_SYS_PTRACE)) + return 0; + return -EPERM; +} + +int cap_ptrace_traceme(struct task_struct *parent) +{ + /* Derived from arch/i386/kernel/ptrace.c:sys_ptrace. */ + if (cap_issubset(current->cap_permitted, parent->cap_permitted)) + return 0; + if (has_capability(parent, CAP_SYS_PTRACE)) + return 0; + return -EPERM; } int cap_capget (struct task_struct *target, kernel_cap_t *effective, @@ -534,7 +544,7 @@ int cap_task_post_setuid (uid_t old_ruid, uid_t old_euid, uid_t old_suid, static inline int cap_safe_nice(struct task_struct *p) { if (!cap_issubset(p->cap_permitted, current->cap_permitted) && - !__capable(current, CAP_SYS_NICE)) + !capable(CAP_SYS_NICE)) return -EPERM; return 0; } diff --git a/security/root_plug.c b/security/root_plug.c index be0ebec2580..c3f68b5b372 100644 --- a/security/root_plug.c +++ b/security/root_plug.c @@ -72,7 +72,8 @@ static int rootplug_bprm_check_security (struct linux_binprm *bprm) static struct security_operations rootplug_security_ops = { /* Use the capability functions for some of the hooks */ - .ptrace = cap_ptrace, + .ptrace_may_access = cap_ptrace_may_access, + .ptrace_traceme = cap_ptrace_traceme, .capget = cap_capget, .capset_check = cap_capset_check, .capset_set = cap_capset_set, diff --git a/security/security.c b/security/security.c index ff706872775..3a4b4f55b33 100644 --- a/security/security.c +++ b/security/security.c @@ -127,10 +127,14 @@ int register_security(struct security_operations *ops) /* Security operations */ -int security_ptrace(struct task_struct *parent, struct task_struct *child, - unsigned int mode) +int security_ptrace_may_access(struct task_struct *child, unsigned int mode) { - return security_ops->ptrace(parent, child, mode); + return security_ops->ptrace_may_access(child, mode); +} + +int security_ptrace_traceme(struct task_struct *parent) +{ + return security_ops->ptrace_traceme(parent); } int security_capget(struct task_struct *target, diff --git a/security/selinux/hooks.c b/security/selinux/hooks.c index 3ae9bec5a50..03fc6a81ae3 100644 --- a/security/selinux/hooks.c +++ b/security/selinux/hooks.c @@ -1738,24 +1738,34 @@ static inline u32 file_to_av(struct file *file) /* Hook functions begin here. */ -static int selinux_ptrace(struct task_struct *parent, - struct task_struct *child, - unsigned int mode) +static int selinux_ptrace_may_access(struct task_struct *child, + unsigned int mode) { int rc; - rc = secondary_ops->ptrace(parent, child, mode); + rc = secondary_ops->ptrace_may_access(child, mode); if (rc) return rc; if (mode == PTRACE_MODE_READ) { - struct task_security_struct *tsec = parent->security; + struct task_security_struct *tsec = current->security; struct task_security_struct *csec = child->security; return avc_has_perm(tsec->sid, csec->sid, SECCLASS_FILE, FILE__READ, NULL); } - return task_has_perm(parent, child, PROCESS__PTRACE); + return task_has_perm(current, child, PROCESS__PTRACE); +} + +static int selinux_ptrace_traceme(struct task_struct *parent) +{ + int rc; + + rc = secondary_ops->ptrace_traceme(parent); + if (rc) + return rc; + + return task_has_perm(parent, current, PROCESS__PTRACE); } static int selinux_capget(struct task_struct *target, kernel_cap_t *effective, @@ -5346,7 +5356,8 @@ static int selinux_key_getsecurity(struct key *key, char **_buffer) static struct security_operations selinux_ops = { .name = "selinux", - .ptrace = selinux_ptrace, + .ptrace_may_access = selinux_ptrace_may_access, + .ptrace_traceme = selinux_ptrace_traceme, .capget = selinux_capget, .capset_check = selinux_capset_check, .capset_set = selinux_capset_set, diff --git a/security/smack/smack_lsm.c b/security/smack/smack_lsm.c index 1b40e558f98..87d75417ea9 100644 --- a/security/smack/smack_lsm.c +++ b/security/smack/smack_lsm.c @@ -87,27 +87,46 @@ struct inode_smack *new_inode_smack(char *smack) */ /** - * smack_ptrace - Smack approval on ptrace - * @ptp: parent task pointer + * smack_ptrace_may_access - Smack approval on PTRACE_ATTACH * @ctp: child task pointer * * Returns 0 if access is OK, an error code otherwise * * Do the capability checks, and require read and write. */ -static int smack_ptrace(struct task_struct *ptp, struct task_struct *ctp, - unsigned int mode) +static int smack_ptrace_may_access(struct task_struct *ctp, unsigned int mode) { int rc; - rc = cap_ptrace(ptp, ctp, mode); + rc = cap_ptrace_may_access(ctp, mode); if (rc != 0) return rc; - rc = smk_access(ptp->security, ctp->security, MAY_READWRITE); - if (rc != 0 && __capable(ptp, CAP_MAC_OVERRIDE)) + rc = smk_access(current->security, ctp->security, MAY_READWRITE); + if (rc != 0 && capable(CAP_MAC_OVERRIDE)) return 0; + return rc; +} + +/** + * smack_ptrace_traceme - Smack approval on PTRACE_TRACEME + * @ptp: parent task pointer + * + * Returns 0 if access is OK, an error code otherwise + * + * Do the capability checks, and require read and write. + */ +static int smack_ptrace_traceme(struct task_struct *ptp) +{ + int rc; + + rc = cap_ptrace_traceme(ptp); + if (rc != 0) + return rc; + rc = smk_access(ptp->security, current->security, MAY_READWRITE); + if (rc != 0 && has_capability(ptp, CAP_MAC_OVERRIDE)) + return 0; return rc; } @@ -923,7 +942,7 @@ static int smack_file_send_sigiotask(struct task_struct *tsk, */ file = container_of(fown, struct file, f_owner); rc = smk_access(file->f_security, tsk->security, MAY_WRITE); - if (rc != 0 && __capable(tsk, CAP_MAC_OVERRIDE)) + if (rc != 0 && has_capability(tsk, CAP_MAC_OVERRIDE)) return 0; return rc; } @@ -1164,12 +1183,12 @@ static int smack_task_wait(struct task_struct *p) * account for the smack labels having gotten to * be different in the first place. * - * This breaks the strict subjet/object access + * This breaks the strict subject/object access * control ideal, taking the object's privilege * state into account in the decision as well as * the smack value. */ - if (capable(CAP_MAC_OVERRIDE) || __capable(p, CAP_MAC_OVERRIDE)) + if (capable(CAP_MAC_OVERRIDE) || has_capability(p, CAP_MAC_OVERRIDE)) return 0; return rc; @@ -2016,9 +2035,6 @@ static int smack_setprocattr(struct task_struct *p, char *name, { char *newsmack; - if (!__capable(p, CAP_MAC_ADMIN)) - return -EPERM; - /* * Changing another process' Smack value is too dangerous * and supports no sane use case. @@ -2026,6 +2042,9 @@ static int smack_setprocattr(struct task_struct *p, char *name, if (p != current) return -EPERM; + if (!capable(CAP_MAC_ADMIN)) + return -EPERM; + if (value == NULL || size == 0 || size >= SMK_LABELLEN) return -EINVAL; @@ -2552,7 +2571,8 @@ static void smack_release_secctx(char *secdata, u32 seclen) struct security_operations smack_ops = { .name = "smack", - .ptrace = smack_ptrace, + .ptrace_may_access = smack_ptrace_may_access, + .ptrace_traceme = smack_ptrace_traceme, .capget = cap_capget, .capset_check = cap_capset_check, .capset_set = cap_capset_set, @@ -2729,4 +2749,3 @@ static __init int smack_init(void) * all processes and objects when they are created. */ security_initcall(smack_init); - -- GitLab From f1679d08480008e06fd619c71635ed33274e2595 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Thu, 14 Aug 2008 15:49:00 +0200 Subject: [PATCH 374/750] sched: fix rt-bandwidth hotplug race When we hot-unplug a cpu and rebuild the sched-domain, all cpus will be detatched. Alex observed the case where a runqueue was stealing bandwidth from an already disabled runqueue to satisfy its own needs. Stop this by skipping over already disabled runqueues. Reported-by: Alex Nixon Signed-off-by: Peter Zijlstra Tested-by: Alex Nixon Signed-off-by: Ingo Molnar --- kernel/sched_rt.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/sched_rt.c b/kernel/sched_rt.c index 6163e4cf885..998ba54b454 100644 --- a/kernel/sched_rt.c +++ b/kernel/sched_rt.c @@ -298,7 +298,7 @@ static void __disable_runtime(struct rq *rq) struct rt_rq *iter = sched_rt_period_rt_rq(rt_b, i); s64 diff; - if (iter == rt_rq) + if (iter == rt_rq || iter->rt_runtime == RUNTIME_INF) continue; spin_lock(&iter->rt_runtime_lock); -- GitLab From 7c6337a15e3d4689efe703e8bb65ae82cc13c435 Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Thu, 14 Aug 2008 15:29:09 -0700 Subject: [PATCH 375/750] bnx2: Fix logic to setup VLAN rx tagging. We should now be checking BNX2_FLAG_CAN_KEEP_VLAN to determine how to set the VLAN rx tagging in the RX_MODE register. Signed-off-by: Michael Chan Signed-off-by: Benjamin Li Signed-off-by: Matt Carlson Signed-off-by: David S. Miller --- drivers/net/bnx2.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/bnx2.c b/drivers/net/bnx2.c index 5ebde67d429..0623ceb7a0e 100644 --- a/drivers/net/bnx2.c +++ b/drivers/net/bnx2.c @@ -3237,10 +3237,10 @@ bnx2_set_rx_mode(struct net_device *dev) BNX2_EMAC_RX_MODE_KEEP_VLAN_TAG); sort_mode = 1 | BNX2_RPM_SORT_USER0_BC_EN; #ifdef BCM_VLAN - if (!bp->vlgrp && !(bp->flags & BNX2_FLAG_ASF_ENABLE)) + if (!bp->vlgrp && (bp->flags & BNX2_FLAG_CAN_KEEP_VLAN)) rx_mode |= BNX2_EMAC_RX_MODE_KEEP_VLAN_TAG; #else - if (!(bp->flags & BNX2_FLAG_ASF_ENABLE)) + if (bp->flags & BNX2_FLAG_CAN_KEEP_VLAN) rx_mode |= BNX2_EMAC_RX_MODE_KEEP_VLAN_TAG; #endif if (dev->flags & IFF_PROMISC) { -- GitLab From 729b85cd47f4e63657505cb5c6af104e19250805 Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Thu, 14 Aug 2008 15:29:39 -0700 Subject: [PATCH 376/750] bnx2: Use proper CONFIG_VLAN_8021Q to compile the VLAN code. Signed-off-by: Michael Chan Signed-off-by: Benjamin Li Signed-off-by: Matt Carlson Signed-off-by: David S. Miller --- drivers/net/bnx2.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/net/bnx2.c b/drivers/net/bnx2.c index 0623ceb7a0e..a2a010ede59 100644 --- a/drivers/net/bnx2.c +++ b/drivers/net/bnx2.c @@ -35,7 +35,7 @@ #include #include #include -#ifdef NETIF_F_HW_VLAN_TX +#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE) #include #define BCM_VLAN 1 #endif @@ -5963,10 +5963,12 @@ bnx2_start_xmit(struct sk_buff *skb, struct net_device *dev) vlan_tag_flags |= TX_BD_FLAGS_TCP_UDP_CKSUM; } +#ifdef BCM_VLAN if (bp->vlgrp && vlan_tx_tag_present(skb)) { vlan_tag_flags |= (TX_BD_FLAGS_VLAN_TAG | (vlan_tx_tag_get(skb) << 16)); } +#endif if ((mss = skb_shinfo(skb)->gso_size)) { u32 tcp_opt_len, ip_tcp_len; struct iphdr *iph; -- GitLab From f22828e89f4f3e8c74ca7ffa69b0410afbd80eee Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Thu, 14 Aug 2008 15:30:14 -0700 Subject: [PATCH 377/750] bnx2: Reinsert VLAN tag when necessary. In certain cases when ASF or other management firmware is running, the chip may be configured to always strip out the VLAN tag even when VLAN acceleration is not enabled. This causes some VLAN tagged packets to be received by the host stack without any knowledge that the original packet was VLAN tagged. We fix this by re-inserting the VLAN tag into the packet when necessary. Signed-off-by: Michael Chan Signed-off-by: Benjamin Li Signed-off-by: Matt Carlson Signed-off-by: David S. Miller --- drivers/net/bnx2.c | 35 +++++++++++++++++++++++++++-------- 1 file changed, 27 insertions(+), 8 deletions(-) diff --git a/drivers/net/bnx2.c b/drivers/net/bnx2.c index a2a010ede59..1f2e76fda01 100644 --- a/drivers/net/bnx2.c +++ b/drivers/net/bnx2.c @@ -2876,6 +2876,8 @@ bnx2_rx_int(struct bnx2 *bp, struct bnx2_napi *bnapi, int budget) struct sw_bd *rx_buf; struct sk_buff *skb; dma_addr_t dma_addr; + u16 vtag = 0; + int hw_vlan __maybe_unused = 0; sw_ring_cons = RX_RING_IDX(sw_cons); sw_ring_prod = RX_RING_IDX(sw_prod); @@ -2919,7 +2921,7 @@ bnx2_rx_int(struct bnx2 *bp, struct bnx2_napi *bnapi, int budget) if (len <= bp->rx_copy_thresh) { struct sk_buff *new_skb; - new_skb = netdev_alloc_skb(bp->dev, len + 2); + new_skb = netdev_alloc_skb(bp->dev, len + 6); if (new_skb == NULL) { bnx2_reuse_rx_skb(bp, rxr, skb, sw_ring_cons, sw_ring_prod); @@ -2928,9 +2930,9 @@ bnx2_rx_int(struct bnx2 *bp, struct bnx2_napi *bnapi, int budget) /* aligned copy */ skb_copy_from_linear_data_offset(skb, - BNX2_RX_OFFSET - 2, - new_skb->data, len + 2); - skb_reserve(new_skb, 2); + BNX2_RX_OFFSET - 6, + new_skb->data, len + 6); + skb_reserve(new_skb, 6); skb_put(new_skb, len); bnx2_reuse_rx_skb(bp, rxr, skb, @@ -2941,6 +2943,25 @@ bnx2_rx_int(struct bnx2 *bp, struct bnx2_napi *bnapi, int budget) dma_addr, (sw_ring_cons << 16) | sw_ring_prod))) goto next_rx; + if ((status & L2_FHDR_STATUS_L2_VLAN_TAG) && + !(bp->rx_mode & BNX2_EMAC_RX_MODE_KEEP_VLAN_TAG)) { + vtag = rx_hdr->l2_fhdr_vlan_tag; +#ifdef BCM_VLAN + if (bp->vlgrp) + hw_vlan = 1; + else +#endif + { + struct vlan_ethhdr *ve = (struct vlan_ethhdr *) + __skb_push(skb, 4); + + memmove(ve, skb->data + 4, ETH_ALEN * 2); + ve->h_vlan_proto = htons(ETH_P_8021Q); + ve->h_vlan_TCI = htons(vtag); + len += 4; + } + } + skb->protocol = eth_type_trans(skb, bp->dev); if ((len > (bp->dev->mtu + ETH_HLEN)) && @@ -2962,10 +2983,8 @@ bnx2_rx_int(struct bnx2 *bp, struct bnx2_napi *bnapi, int budget) } #ifdef BCM_VLAN - if ((status & L2_FHDR_STATUS_L2_VLAN_TAG) && bp->vlgrp) { - vlan_hwaccel_receive_skb(skb, bp->vlgrp, - rx_hdr->l2_fhdr_vlan_tag); - } + if (hw_vlan) + vlan_hwaccel_receive_skb(skb, bp->vlgrp, vtag); else #endif netif_receive_skb(skb); -- GitLab From 0eb8b1fe9238ca4c1797e4c105d5790abda1726f Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Thu, 14 Aug 2008 15:30:31 -0700 Subject: [PATCH 378/750] bnx2: Update version to 1.8.0. Signed-off-by: Michael Chan Signed-off-by: David S. Miller --- drivers/net/bnx2.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/bnx2.c b/drivers/net/bnx2.c index 1f2e76fda01..d4548101e49 100644 --- a/drivers/net/bnx2.c +++ b/drivers/net/bnx2.c @@ -57,8 +57,8 @@ #define DRV_MODULE_NAME "bnx2" #define PFX DRV_MODULE_NAME ": " -#define DRV_MODULE_VERSION "1.7.9" -#define DRV_MODULE_RELDATE "July 18, 2008" +#define DRV_MODULE_VERSION "1.8.0" +#define DRV_MODULE_RELDATE "Aug 14, 2008" #define RUN_AT(x) (jiffies + (x)) -- GitLab From 191cd582500f49b32a63040fedeebb0168c720af Mon Sep 17 00:00:00 2001 From: Brian Haley Date: Thu, 14 Aug 2008 15:33:21 -0700 Subject: [PATCH 379/750] netns: Add network namespace argument to rt6_fill_node() and ipv6_dev_get_saddr() ipv6_dev_get_saddr() blindly de-references dst_dev to get the network namespace, but some callers might pass NULL. Change callers to pass a namespace pointer instead. Signed-off-by: Brian Haley Signed-off-by: David S. Miller --- include/net/addrconf.h | 3 ++- include/net/ip6_route.h | 1 + net/ipv6/addrconf.c | 3 +-- net/ipv6/fib6_rules.c | 3 ++- net/ipv6/ip6_fib.c | 1 + net/ipv6/ip6_output.c | 2 +- net/ipv6/ndisc.c | 2 +- net/ipv6/route.c | 12 +++++++----- net/ipv6/xfrm6_policy.c | 4 +++- net/sctp/ipv6.c | 3 ++- 10 files changed, 21 insertions(+), 13 deletions(-) diff --git a/include/net/addrconf.h b/include/net/addrconf.h index 06b28142b3a..c216de528b0 100644 --- a/include/net/addrconf.h +++ b/include/net/addrconf.h @@ -80,7 +80,8 @@ extern struct inet6_ifaddr *ipv6_get_ifaddr(struct net *net, struct net_device *dev, int strict); -extern int ipv6_dev_get_saddr(struct net_device *dev, +extern int ipv6_dev_get_saddr(struct net *net, + struct net_device *dev, const struct in6_addr *daddr, unsigned int srcprefs, struct in6_addr *saddr); diff --git a/include/net/ip6_route.h b/include/net/ip6_route.h index bc391ba101e..5f53db7e4e5 100644 --- a/include/net/ip6_route.h +++ b/include/net/ip6_route.h @@ -107,6 +107,7 @@ struct rt6_rtnl_dump_arg { struct sk_buff *skb; struct netlink_callback *cb; + struct net *net; }; extern int rt6_dump_route(struct rt6_info *rt, void *p_arg); diff --git a/net/ipv6/addrconf.c b/net/ipv6/addrconf.c index a7842c54f58..e2d3b7580b7 100644 --- a/net/ipv6/addrconf.c +++ b/net/ipv6/addrconf.c @@ -1106,13 +1106,12 @@ out: return ret; } -int ipv6_dev_get_saddr(struct net_device *dst_dev, +int ipv6_dev_get_saddr(struct net *net, struct net_device *dst_dev, const struct in6_addr *daddr, unsigned int prefs, struct in6_addr *saddr) { struct ipv6_saddr_score scores[2], *score = &scores[0], *hiscore = &scores[1]; - struct net *net = dev_net(dst_dev); struct ipv6_saddr_dst dst; struct net_device *dev; int dst_type; diff --git a/net/ipv6/fib6_rules.c b/net/ipv6/fib6_rules.c index 8d05527524e..f5de3f9dc69 100644 --- a/net/ipv6/fib6_rules.c +++ b/net/ipv6/fib6_rules.c @@ -93,7 +93,8 @@ static int fib6_rule_action(struct fib_rule *rule, struct flowi *flp, if (flags & RT6_LOOKUP_F_SRCPREF_COA) srcprefs |= IPV6_PREFER_SRC_COA; - if (ipv6_dev_get_saddr(ip6_dst_idev(&rt->u.dst)->dev, + if (ipv6_dev_get_saddr(net, + ip6_dst_idev(&rt->u.dst)->dev, &flp->fl6_dst, srcprefs, &saddr)) goto again; diff --git a/net/ipv6/ip6_fib.c b/net/ipv6/ip6_fib.c index 52dddc25d3e..29c7c99e69f 100644 --- a/net/ipv6/ip6_fib.c +++ b/net/ipv6/ip6_fib.c @@ -378,6 +378,7 @@ static int inet6_dump_fib(struct sk_buff *skb, struct netlink_callback *cb) arg.skb = skb; arg.cb = cb; + arg.net = net; w->args = &arg; for (h = s_h; h < FIB_TABLE_HASHSZ; h++, s_e = 0) { diff --git a/net/ipv6/ip6_output.c b/net/ipv6/ip6_output.c index a4402de425d..0e844c2736a 100644 --- a/net/ipv6/ip6_output.c +++ b/net/ipv6/ip6_output.c @@ -934,7 +934,7 @@ static int ip6_dst_lookup_tail(struct sock *sk, goto out_err_release; if (ipv6_addr_any(&fl->fl6_src)) { - err = ipv6_dev_get_saddr(ip6_dst_idev(*dst)->dev, + err = ipv6_dev_get_saddr(net, ip6_dst_idev(*dst)->dev, &fl->fl6_dst, sk ? inet6_sk(sk)->srcprefs : 0, &fl->fl6_src); diff --git a/net/ipv6/ndisc.c b/net/ipv6/ndisc.c index beb48e3f038..f1c62ba0f56 100644 --- a/net/ipv6/ndisc.c +++ b/net/ipv6/ndisc.c @@ -549,7 +549,7 @@ static void ndisc_send_na(struct net_device *dev, struct neighbour *neigh, override = 0; in6_ifa_put(ifp); } else { - if (ipv6_dev_get_saddr(dev, daddr, + if (ipv6_dev_get_saddr(dev_net(dev), dev, daddr, inet6_sk(dev_net(dev)->ipv6.ndisc_sk)->srcprefs, &tmpaddr)) return; diff --git a/net/ipv6/route.c b/net/ipv6/route.c index 41b165ffb36..9af6115f0f5 100644 --- a/net/ipv6/route.c +++ b/net/ipv6/route.c @@ -2106,7 +2106,8 @@ static inline size_t rt6_nlmsg_size(void) + nla_total_size(sizeof(struct rta_cacheinfo)); } -static int rt6_fill_node(struct sk_buff *skb, struct rt6_info *rt, +static int rt6_fill_node(struct net *net, + struct sk_buff *skb, struct rt6_info *rt, struct in6_addr *dst, struct in6_addr *src, int iif, int type, u32 pid, u32 seq, int prefix, int nowait, unsigned int flags) @@ -2189,7 +2190,7 @@ static int rt6_fill_node(struct sk_buff *skb, struct rt6_info *rt, } else if (dst) { struct inet6_dev *idev = ip6_dst_idev(&rt->u.dst); struct in6_addr saddr_buf; - if (ipv6_dev_get_saddr(idev ? idev->dev : NULL, + if (ipv6_dev_get_saddr(net, idev ? idev->dev : NULL, dst, 0, &saddr_buf) == 0) NLA_PUT(skb, RTA_PREFSRC, 16, &saddr_buf); } @@ -2234,7 +2235,8 @@ int rt6_dump_route(struct rt6_info *rt, void *p_arg) } else prefix = 0; - return rt6_fill_node(arg->skb, rt, NULL, NULL, 0, RTM_NEWROUTE, + return rt6_fill_node(arg->net, + arg->skb, rt, NULL, NULL, 0, RTM_NEWROUTE, NETLINK_CB(arg->cb->skb).pid, arg->cb->nlh->nlmsg_seq, prefix, 0, NLM_F_MULTI); } @@ -2300,7 +2302,7 @@ static int inet6_rtm_getroute(struct sk_buff *in_skb, struct nlmsghdr* nlh, void rt = (struct rt6_info*) ip6_route_output(net, NULL, &fl); skb->dst = &rt->u.dst; - err = rt6_fill_node(skb, rt, &fl.fl6_dst, &fl.fl6_src, iif, + err = rt6_fill_node(net, skb, rt, &fl.fl6_dst, &fl.fl6_src, iif, RTM_NEWROUTE, NETLINK_CB(in_skb).pid, nlh->nlmsg_seq, 0, 0, 0); if (err < 0) { @@ -2327,7 +2329,7 @@ void inet6_rt_notify(int event, struct rt6_info *rt, struct nl_info *info) if (skb == NULL) goto errout; - err = rt6_fill_node(skb, rt, NULL, NULL, 0, + err = rt6_fill_node(net, skb, rt, NULL, NULL, 0, event, info->pid, seq, 0, 0, 0); if (err < 0) { /* -EMSGSIZE implies BUG in rt6_nlmsg_size() */ diff --git a/net/ipv6/xfrm6_policy.c b/net/ipv6/xfrm6_policy.c index 8f1e0543b3c..08e4cbbe3f0 100644 --- a/net/ipv6/xfrm6_policy.c +++ b/net/ipv6/xfrm6_policy.c @@ -52,12 +52,14 @@ static struct dst_entry *xfrm6_dst_lookup(int tos, xfrm_address_t *saddr, static int xfrm6_get_saddr(xfrm_address_t *saddr, xfrm_address_t *daddr) { struct dst_entry *dst; + struct net_device *dev; dst = xfrm6_dst_lookup(0, NULL, daddr); if (IS_ERR(dst)) return -EHOSTUNREACH; - ipv6_dev_get_saddr(ip6_dst_idev(dst)->dev, + dev = ip6_dst_idev(dst)->dev; + ipv6_dev_get_saddr(dev_net(dev), dev, (struct in6_addr *)&daddr->a6, 0, (struct in6_addr *)&saddr->a6); dst_release(dst); diff --git a/net/sctp/ipv6.c b/net/sctp/ipv6.c index 483a01d0740..47f91afa021 100644 --- a/net/sctp/ipv6.c +++ b/net/sctp/ipv6.c @@ -319,7 +319,8 @@ static void sctp_v6_get_saddr(struct sctp_sock *sk, __func__, asoc, dst, NIP6(daddr->v6.sin6_addr)); if (!asoc) { - ipv6_dev_get_saddr(dst ? ip6_dst_idev(dst)->dev : NULL, + ipv6_dev_get_saddr(sock_net(sctp_opt2sk(sk)), + dst ? ip6_dst_idev(dst)->dev : NULL, &daddr->v6.sin6_addr, inet6_sk(&sk->inet.sk)->srcprefs, &saddr->v6.sin6_addr); -- GitLab From 323c048836f73a11ded6f9743feda21c00465cb0 Mon Sep 17 00:00:00 2001 From: Jarek Poplawski Date: Thu, 14 Aug 2008 17:01:10 -0700 Subject: [PATCH 380/750] pkt_sched: Fix unlocking in tc_ctl_tfilter() Fix a bug with spin_lock_bh() inserted instead of spin_unlock_bh() by some recent patch. Reported-by: Denys Fedoryshchenko Signed-off-by: Jarek Poplawski Signed-off-by: David S. Miller --- net/sched/cls_api.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/sched/cls_api.c b/net/sched/cls_api.c index d2b6f54a626..5cafdd4c801 100644 --- a/net/sched/cls_api.c +++ b/net/sched/cls_api.c @@ -280,7 +280,7 @@ replay: if (n->nlmsg_type == RTM_DELTFILTER && t->tcm_handle == 0) { spin_lock_bh(root_lock); *back = tp->next; - spin_lock_bh(root_lock); + spin_unlock_bh(root_lock); tfilter_notify(skb, n, tp, fh, RTM_DELTFILTER); tcf_destroy(tp); -- GitLab From 2843ae7734075f5d7072cf1230758bf8cf840af7 Mon Sep 17 00:00:00 2001 From: Bob Moore Date: Fri, 4 Jul 2008 10:41:41 +0800 Subject: [PATCH 381/750] ACPICA: Fix memory leak when deleting thermal/processor objects Fixes a possible memory leak when thermal and processor objects are deleted. Any associated notify handlers (and objects) were not being deleted. Fiodor Suietov. BZ 506 http://www.acpica.org/bugzilla/show_bug.cgi?id=506 Signed-off-by: Fiodor Suietov Signed-off-by: Bob Moore Signed-off-by: Lin Ming Signed-off-by: Andi Kleen --- drivers/acpi/utilities/utdelete.c | 13 +++++++++++-- 1 file changed, 11 insertions(+), 2 deletions(-) diff --git a/drivers/acpi/utilities/utdelete.c b/drivers/acpi/utilities/utdelete.c index c5c791a575c..42609d3a8aa 100644 --- a/drivers/acpi/utilities/utdelete.c +++ b/drivers/acpi/utilities/utdelete.c @@ -135,6 +135,10 @@ static void acpi_ut_delete_internal_obj(union acpi_operand_object *object) obj_pointer = object->package.elements; break; + /* + * These objects have a possible list of notify handlers. + * Device object also may have a GPE block. + */ case ACPI_TYPE_DEVICE: if (object->device.gpe_block) { @@ -142,9 +146,14 @@ static void acpi_ut_delete_internal_obj(union acpi_operand_object *object) gpe_block); } - /* Walk the handler list for this device */ + /*lint -fallthrough */ + + case ACPI_TYPE_PROCESSOR: + case ACPI_TYPE_THERMAL: + + /* Walk the notify handler list for this object */ - handler_desc = object->device.handler; + handler_desc = object->common_notify.handler; while (handler_desc) { next_desc = handler_desc->address_space.next; acpi_ut_remove_reference(handler_desc); -- GitLab From d3ff268a0149fce8835f6d48ab481d5e3321e0f7 Mon Sep 17 00:00:00 2001 From: Lin Ming Date: Fri, 4 Jul 2008 10:51:41 +0800 Subject: [PATCH 382/750] ACPICA: Fix possible memory leak in Unload() operator The DdbHandle returned by Load() does not have its reference count decremented during unload, leading to a memory leak. Lin Ming. Signed-off-by: Lin Ming Signed-off-by: Bob Moore Signed-off-by: Andi Kleen --- drivers/acpi/executer/exconfig.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/acpi/executer/exconfig.c b/drivers/acpi/executer/exconfig.c index 2a32c843cb4..8892b9824fa 100644 --- a/drivers/acpi/executer/exconfig.c +++ b/drivers/acpi/executer/exconfig.c @@ -479,5 +479,8 @@ acpi_status acpi_ex_unload_table(union acpi_operand_object *ddb_handle) acpi_tb_set_table_loaded_flag(table_index, FALSE); + /* Table unloaded, remove a reference to the ddb_handle object */ + + acpi_ut_remove_reference(ddb_handle); return_ACPI_STATUS(AE_OK); } -- GitLab From 3c7db22a194d3b53584047425af82b4e1e03d9f7 Mon Sep 17 00:00:00 2001 From: Bob Moore Date: Mon, 4 Aug 2008 11:13:01 +0800 Subject: [PATCH 383/750] ACPICA: Additional error checking for pathname utilities Add error check after all calls to acpi_ns_get_pathname_length. Add status return from acpi_ns_build_external_path and check after all calls. Add parameter validation to acpi_ut_initialize_buffer. Reported by and initial patch by Ingo Molnar. http://lkml.org/lkml/2008/7/21/176 Signed-off-by: Bob Moore Signed-off-by: Lin Ming Signed-off-by: Andi Kleen --- drivers/acpi/namespace/nsnames.c | 34 ++++++++++++++++++++----------- drivers/acpi/resources/rscalc.c | 3 +++ drivers/acpi/utilities/utalloc.c | 8 +++++--- drivers/acpi/utilities/utobject.c | 13 ++++++++---- include/acpi/acnamesp.h | 2 +- 5 files changed, 40 insertions(+), 20 deletions(-) diff --git a/drivers/acpi/namespace/nsnames.c b/drivers/acpi/namespace/nsnames.c index 549db42f16c..bd577387800 100644 --- a/drivers/acpi/namespace/nsnames.c +++ b/drivers/acpi/namespace/nsnames.c @@ -56,13 +56,14 @@ ACPI_MODULE_NAME("nsnames") * Size - Size of the pathname * *name_buffer - Where to return the pathname * - * RETURN: Places the pathname into the name_buffer, in external format + * RETURN: Status + * Places the pathname into the name_buffer, in external format * (name segments separated by path separators) * * DESCRIPTION: Generate a full pathaname * ******************************************************************************/ -void +acpi_status acpi_ns_build_external_path(struct acpi_namespace_node *node, acpi_size size, char *name_buffer) { @@ -77,7 +78,7 @@ acpi_ns_build_external_path(struct acpi_namespace_node *node, if (index < ACPI_NAME_SIZE) { name_buffer[0] = AML_ROOT_PREFIX; name_buffer[1] = 0; - return; + return (AE_OK); } /* Store terminator byte, then build name backwards */ @@ -105,11 +106,13 @@ acpi_ns_build_external_path(struct acpi_namespace_node *node, if (index != 0) { ACPI_ERROR((AE_INFO, - "Could not construct pathname; index=%X, size=%X, Path=%s", + "Could not construct external pathname; index=%X, size=%X, Path=%s", (u32) index, (u32) size, &name_buffer[size])); + + return (AE_BAD_PARAMETER); } - return; + return (AE_OK); } #ifdef ACPI_DEBUG_OUTPUT @@ -129,6 +132,7 @@ acpi_ns_build_external_path(struct acpi_namespace_node *node, char *acpi_ns_get_external_pathname(struct acpi_namespace_node *node) { + acpi_status status; char *name_buffer; acpi_size size; @@ -138,8 +142,7 @@ char *acpi_ns_get_external_pathname(struct acpi_namespace_node *node) size = acpi_ns_get_pathname_length(node); if (!size) { - ACPI_ERROR((AE_INFO, "Invalid node failure")); - return_PTR(NULL); + return (NULL); } /* Allocate a buffer to be returned to caller */ @@ -152,7 +155,11 @@ char *acpi_ns_get_external_pathname(struct acpi_namespace_node *node) /* Build the path in the allocated buffer */ - acpi_ns_build_external_path(node, size, name_buffer); + status = acpi_ns_build_external_path(node, size, name_buffer); + if (ACPI_FAILURE(status)) { + return (NULL); + } + return_PTR(name_buffer); } #endif @@ -186,7 +193,7 @@ acpi_size acpi_ns_get_pathname_length(struct acpi_namespace_node *node) while (next_node && (next_node != acpi_gbl_root_node)) { if (ACPI_GET_DESCRIPTOR_TYPE(next_node) != ACPI_DESC_TYPE_NAMED) { ACPI_ERROR((AE_INFO, - "Invalid NS Node (%p) while traversing path", + "Invalid Namespace Node (%p) while traversing namespace", next_node)); return 0; } @@ -234,8 +241,7 @@ acpi_ns_handle_to_pathname(acpi_handle target_handle, required_size = acpi_ns_get_pathname_length(node); if (!required_size) { - ACPI_ERROR((AE_INFO, "Invalid node failure")); - return_ACPI_STATUS(AE_ERROR); + return_ACPI_STATUS(AE_BAD_PARAMETER); } /* Validate/Allocate/Clear caller buffer */ @@ -247,7 +253,11 @@ acpi_ns_handle_to_pathname(acpi_handle target_handle, /* Build the path in the caller buffer */ - acpi_ns_build_external_path(node, required_size, buffer->pointer); + status = + acpi_ns_build_external_path(node, required_size, buffer->pointer); + if (ACPI_FAILURE(status)) { + return_ACPI_STATUS(status); + } ACPI_DEBUG_PRINT((ACPI_DB_EXEC, "%s [%X]\n", (char *)buffer->pointer, (u32) required_size)); diff --git a/drivers/acpi/resources/rscalc.c b/drivers/acpi/resources/rscalc.c index f61ebc679e6..d9063ea414e 100644 --- a/drivers/acpi/resources/rscalc.c +++ b/drivers/acpi/resources/rscalc.c @@ -587,6 +587,9 @@ acpi_rs_get_pci_routing_table_length(union acpi_operand_object *package_object, } else { temp_size_needed += acpi_ns_get_pathname_length((*sub_object_list)->reference.node); + if (!temp_size_needed) { + return_ACPI_STATUS(AE_BAD_PARAMETER); + } } } else { /* diff --git a/drivers/acpi/utilities/utalloc.c b/drivers/acpi/utilities/utalloc.c index e7bf34a7b1d..7dcb67e0b21 100644 --- a/drivers/acpi/utilities/utalloc.c +++ b/drivers/acpi/utilities/utalloc.c @@ -242,10 +242,12 @@ acpi_ut_initialize_buffer(struct acpi_buffer * buffer, { acpi_status status = AE_OK; - if (!required_length) { - WARN_ON(1); - return AE_ERROR; + /* Parameter validation */ + + if (!buffer || !required_length) { + return (AE_BAD_PARAMETER); } + switch (buffer->length) { case ACPI_NO_BUFFER: diff --git a/drivers/acpi/utilities/utobject.c b/drivers/acpi/utilities/utobject.c index e25484495e6..916eff399eb 100644 --- a/drivers/acpi/utilities/utobject.c +++ b/drivers/acpi/utilities/utobject.c @@ -425,6 +425,7 @@ acpi_ut_get_simple_object_size(union acpi_operand_object *internal_object, acpi_size * obj_length) { acpi_size length; + acpi_size size; acpi_status status = AE_OK; ACPI_FUNCTION_TRACE_PTR(ut_get_simple_object_size, internal_object); @@ -484,10 +485,14 @@ acpi_ut_get_simple_object_size(union acpi_operand_object *internal_object, * Get the actual length of the full pathname to this object. * The reference will be converted to the pathname to the object */ - length += - ACPI_ROUND_UP_TO_NATIVE_WORD - (acpi_ns_get_pathname_length - (internal_object->reference.node)); + size = + acpi_ns_get_pathname_length(internal_object-> + reference.node); + if (!size) { + return_ACPI_STATUS(AE_BAD_PARAMETER); + } + + length += ACPI_ROUND_UP_TO_NATIVE_WORD(size); break; default: diff --git a/include/acpi/acnamesp.h b/include/acpi/acnamesp.h index 9ed70a05058..c34008507b6 100644 --- a/include/acpi/acnamesp.h +++ b/include/acpi/acnamesp.h @@ -182,7 +182,7 @@ acpi_status acpi_ns_evaluate(struct acpi_evaluate_info *info); */ u32 acpi_ns_opens_scope(acpi_object_type type); -void +acpi_status acpi_ns_build_external_path(struct acpi_namespace_node *node, acpi_size size, char *name_buffer); -- GitLab From dab36ad8d50dc9424dfc4926f62aaf9bd52dcf13 Mon Sep 17 00:00:00 2001 From: Carlos Corbacho Date: Sat, 2 Aug 2008 17:28:45 +0100 Subject: [PATCH 384/750] ACPI: WMI: Set instance for query block calls Although the necessary data structure was set up, it was never actually passed in, so data block calls have only been working by sheer chance. (On Acer laptops. the data block methods we've been calling never look at the instance value, hence acer-wmi never triggered this before). f3454ae8104efb2dbf0d08ec42c6f5d0fe9225bc brought this to light. Signed-off-by: Carlos Corbacho Signed-off-by: Andi Kleen --- drivers/acpi/wmi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/acpi/wmi.c b/drivers/acpi/wmi.c index c33b1c6e93b..cfe2c833474 100644 --- a/drivers/acpi/wmi.c +++ b/drivers/acpi/wmi.c @@ -347,7 +347,7 @@ struct acpi_buffer *out) strcpy(method, "WQ"); strncat(method, block->object_id, 2); - status = acpi_evaluate_object(handle, method, NULL, out); + status = acpi_evaluate_object(handle, method, &input, out); /* * If ACPI_WMI_EXPENSIVE, call the relevant WCxx method, even if -- GitLab From 5c742b45dd5fbbb6cf74d3378341704f4b23c5e8 Mon Sep 17 00:00:00 2001 From: Carlos Corbacho Date: Wed, 6 Aug 2008 19:13:56 +0100 Subject: [PATCH 385/750] acer-wmi: Fix wireless and bluetooth on early AMW0 v2 laptops In the old acer_acpi, I discovered that on some of the newer AMW0 laptops that supported the WMID methods, they don't work properly for setting the wireless and bluetooth values. So for the AMW0 V2 laptops, we want to use both the 'old' AMW0 and the 'new' WMID methods for setting wireless & bluetooth to guarantee we always enable it. This was fixed in acer_acpi some time ago, but I forgot to port the patch over to acer-wmi when it was merged. (Without this patch, early AMW0 V2 laptops such as the Aspire 5040 won't work with acer-wmi, where-as they did with the old acer_acpi). AK: fix compilation Signed-off-by: Carlos Corbacho CC: stable@kernel.org Signed-off-by: Andi Kleen --- drivers/misc/acer-wmi.c | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) diff --git a/drivers/misc/acer-wmi.c b/drivers/misc/acer-wmi.c index e7a3fe508df..b2d9878dc3f 100644 --- a/drivers/misc/acer-wmi.c +++ b/drivers/misc/acer-wmi.c @@ -803,11 +803,30 @@ static acpi_status get_u32(u32 *value, u32 cap) static acpi_status set_u32(u32 value, u32 cap) { + acpi_status status; + if (interface->capability & cap) { switch (interface->type) { case ACER_AMW0: return AMW0_set_u32(value, cap, interface); case ACER_AMW0_V2: + if (cap == ACER_CAP_MAILLED) + return AMW0_set_u32(value, cap, interface); + + /* + * On some models, some WMID methods don't toggle + * properly. For those cases, we want to run the AMW0 + * method afterwards to be certain we've really toggled + * the device state. + */ + if (cap == ACER_CAP_WIRELESS || + cap == ACER_CAP_BLUETOOTH) { + status = WMID_set_u32(value, cap, interface); + if (ACPI_FAILURE(status)) + return status; + + return AMW0_set_u32(value, cap, interface); + } case ACER_WMID: return WMID_set_u32(value, cap, interface); default: -- GitLab From d0057413a7a277e104cf315faa1b55b60b4a5482 Mon Sep 17 00:00:00 2001 From: Pavel Machek Date: Tue, 12 Aug 2008 12:24:34 +0200 Subject: [PATCH 386/750] acpi: trivial cleanups Trivial cleanups for ACPI. Fix misspelling in printk(), fix mismerge, add file header. AK: removed file header Signed-off-by: Pavel Machek Signed-off-by: Andi Kleen --- drivers/acpi/processor_core.c | 2 +- drivers/acpi/processor_idle.c | 1 - 2 files changed, 1 insertion(+), 2 deletions(-) diff --git a/drivers/acpi/processor_core.c b/drivers/acpi/processor_core.c index e36422a7122..d3f0a62efcc 100644 --- a/drivers/acpi/processor_core.c +++ b/drivers/acpi/processor_core.c @@ -123,7 +123,7 @@ struct acpi_processor_errata errata __read_mostly; static int set_no_mwait(const struct dmi_system_id *id) { printk(KERN_NOTICE PREFIX "%s detected - " - "disable mwait for CPU C-stetes\n", id->ident); + "disabling mwait for CPU C-states\n", id->ident); idle_nomwait = 1; return 0; } diff --git a/drivers/acpi/processor_idle.c b/drivers/acpi/processor_idle.c index 283c08f5f4d..cf5b1b7b684 100644 --- a/drivers/acpi/processor_idle.c +++ b/drivers/acpi/processor_idle.c @@ -41,7 +41,6 @@ #include #include #include -#include /* * Include the apic definitions for x86 to have the APIC timer related defines -- GitLab From afd7301ddb762b66bf1831b0820b402e5d2c439d Mon Sep 17 00:00:00 2001 From: Holger Macht Date: Wed, 6 Aug 2008 17:56:01 +0200 Subject: [PATCH 387/750] ACPI: Properly clear flags on false-positives and send uevent on sudden unplug Some devices emit a ACPI_NOTIFY_DEVICE_CHECK while physically unplugging even if the software undock has already been done and dock_present() check fails. However, the internal flags need to be cleared (complete_undock()). Also, even notify userspace if the dock station suddently went away without proper software undocking. This happens on a Acer TravelMate 3000 Signed-off-by: Holger Macht Signed-off-by: Andi Kleen --- drivers/acpi/dock.c | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-) diff --git a/drivers/acpi/dock.c b/drivers/acpi/dock.c index bb7c51f712b..7d2edf143f1 100644 --- a/drivers/acpi/dock.c +++ b/drivers/acpi/dock.c @@ -563,9 +563,6 @@ EXPORT_SYMBOL_GPL(unregister_hotplug_dock_device); */ static int handle_eject_request(struct dock_station *ds, u32 event) { - if (!dock_present(ds)) - return -ENODEV; - if (dock_in_progress(ds)) return -EBUSY; @@ -573,8 +570,16 @@ static int handle_eject_request(struct dock_station *ds, u32 event) * here we need to generate the undock * event prior to actually doing the undock * so that the device struct still exists. + * Also, even send the dock event if the + * device is not present anymore */ dock_event(ds, event, UNDOCK_EVENT); + + if (!dock_present(ds)) { + complete_undock(ds); + return -ENODEV; + } + hotplug_dock_devices(ds, ACPI_NOTIFY_EJECT_REQUEST); undock(ds); eject_dock(ds); -- GitLab From 2500822bf4eb0179ef80e5b072c1e0fa83037381 Mon Sep 17 00:00:00 2001 From: Zhao Yakui Date: Tue, 12 Aug 2008 10:40:10 +0800 Subject: [PATCH 388/750] ACPI : Add the EC dmi table to fix the incorrect ECDT table On some ASUS laptops the ECDT gives the incorrect command/status & Data I/O register address. AK: it seems like the command/data addresses are exchanged. In such case it will cause that EC device can't be initialized correctly. To add the EC dmi table is to fix this issue. If the laptop falls into the EC dmi table, the EC command/data I/O address will be fixed. AK: Add comments describing this better http://bugzilla.kernel.org/show_bug.cgi?id=9399 Signed-off-by: Zhao Yakui tested-by : Jan Kasprzak Signed-off-by: Andi Kleen --- drivers/acpi/ec.c | 34 ++++++++++++++++++++++++++++++++++ 1 file changed, 34 insertions(+) diff --git a/drivers/acpi/ec.c b/drivers/acpi/ec.c index 5622aee996b..76784ae7e6a 100644 --- a/drivers/acpi/ec.c +++ b/drivers/acpi/ec.c @@ -110,6 +110,31 @@ static struct acpi_ec { u8 handlers_installed; } *boot_ec, *first_ec; +/* + * Some Asus system have exchanged ECDT data/command IO addresses. + */ +static int print_ecdt_error(const struct dmi_system_id *id) +{ + printk(KERN_NOTICE PREFIX "%s detected - " + "ECDT has exchanged control/data I/O address\n", + id->ident); + return 0; +} + +static struct dmi_system_id __cpuinitdata ec_dmi_table[] = { + { + print_ecdt_error, "Asus L4R", { + DMI_MATCH(DMI_BIOS_VERSION, "1008.006"), + DMI_MATCH(DMI_PRODUCT_NAME, "L4R"), + DMI_MATCH(DMI_BOARD_NAME, "L4R") }, NULL}, + { + print_ecdt_error, "Asus M6R", { + DMI_MATCH(DMI_BIOS_VERSION, "0207"), + DMI_MATCH(DMI_PRODUCT_NAME, "M6R"), + DMI_MATCH(DMI_BOARD_NAME, "M6R") }, NULL}, + {}, +}; + /* -------------------------------------------------------------------------- Transaction Management -------------------------------------------------------------------------- */ @@ -911,6 +936,15 @@ int __init acpi_ec_ecdt_probe(void) pr_info(PREFIX "EC description table is found, configuring boot EC\n"); boot_ec->command_addr = ecdt_ptr->control.address; boot_ec->data_addr = ecdt_ptr->data.address; + if (dmi_check_system(ec_dmi_table)) { + /* + * If the board falls into ec_dmi_table, it means + * that ECDT table gives the incorrect command/status + * & data I/O address. Just fix it. + */ + boot_ec->data_addr = ecdt_ptr->control.address; + boot_ec->command_addr = ecdt_ptr->data.address; + } boot_ec->gpe = ecdt_ptr->gpe; boot_ec->handle = ACPI_ROOT_OBJECT; acpi_get_handle(ACPI_ROOT_OBJECT, ecdt_ptr->id, &boot_ec->handle); -- GitLab From 9d699ed92a459cb408e2577e8bbeabc8ec3989e1 Mon Sep 17 00:00:00 2001 From: Zhao Yakui Date: Mon, 11 Aug 2008 10:33:31 +0800 Subject: [PATCH 389/750] ACPI: Avoid bogus EC timeout when EC is in Polling mode When EC is in Polling mode, OS will check the EC status continually by using the following source code: clear_bit(EC_FLAGS_WAIT_GPE, &ec->flags); while (time_before(jiffies, delay)) { if (acpi_ec_check_status(ec, event)) return 0; msleep(1); } But msleep is realized by the function of schedule_timeout. At the same time although one process is already waken up by some events, it won't be scheduled immediately. So maybe there exists the following phenomena: a. The current jiffies is already after the predefined jiffies. But before timeout happens, OS has no chance to check the EC status again. b. If preemptible schedule is enabled, maybe preempt schedule will happen before checking loop. When the process is resumed again, maybe timeout already happens, which means that OS has no chance to check the EC status. In such case maybe EC status is already what OS expects when timeout happens. But OS has no chance to check the EC status and regards it as AE_TIME. So it will be more appropriate that OS will try to check the EC status again when timeout happens. If the EC status is what we expect, it won't be regarded as timeout. Only when the EC status is not what we expect, it will be regarded as timeout, which means that EC controller can't give a response in time. http://bugzilla.kernel.org/show_bug.cgi?id=9823 http://bugzilla.kernel.org/show_bug.cgi?id=11141 Signed-off-by: Zhao Yakui Signed-off-by: Zhang Rui Signed-off-by: Andi Kleen --- drivers/acpi/ec.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/acpi/ec.c b/drivers/acpi/ec.c index 76784ae7e6a..13593f9f219 100644 --- a/drivers/acpi/ec.c +++ b/drivers/acpi/ec.c @@ -221,6 +221,8 @@ static int acpi_ec_wait(struct acpi_ec *ec, enum ec_event event, int force_poll) return 0; msleep(1); } + if (acpi_ec_check_status(ec,event)) + return 0; } pr_err(PREFIX "acpi_ec_wait timeout, status = 0x%2.2x, event = %s\n", acpi_ec_read_status(ec), -- GitLab From fa46d3526461e8aa7c0fb39cc1b98ac656695a43 Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Fri, 1 Aug 2008 15:58:17 -0600 Subject: [PATCH 390/750] ACPI: bounds check IRQ to prevent memory corruption acpi_penalize_isa_irq() should validate irq before using it to index the acpi_irq_penalty[] table. Here's the path I'm concerned about: pnpacpi_parse_allocated_irqresource() { ... irq = acpi_register_gsi(gsi, triggering, polarity); if (irq >= 0) pcibios_penalize_isa_irq(irq, 1); There's no guarantee that acpi_register_gsi() will return an IRQ within the bounds of acpi_irq_penalty[]. I have not seen a failure I can attribute to this. However, ACPI_MAX_IRQS is only 256, and I'm pretty sure ia64 can have IRQs larger than that. I think this should go in 2.6.27. Signed-off-by: Bjorn Helgaas Signed-off-by: Andi Kleen --- drivers/acpi/pci_link.c | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-) diff --git a/drivers/acpi/pci_link.c b/drivers/acpi/pci_link.c index 89f3b2abfdc..cf47805a744 100644 --- a/drivers/acpi/pci_link.c +++ b/drivers/acpi/pci_link.c @@ -849,7 +849,7 @@ static int __init acpi_irq_penalty_update(char *str, int used) if (irq < 0) continue; - if (irq >= ACPI_MAX_IRQS) + if (irq >= ARRAY_SIZE(acpi_irq_penalty)) continue; if (used) @@ -872,10 +872,12 @@ static int __init acpi_irq_penalty_update(char *str, int used) */ void acpi_penalize_isa_irq(int irq, int active) { - if (active) - acpi_irq_penalty[irq] += PIRQ_PENALTY_ISA_USED; - else - acpi_irq_penalty[irq] += PIRQ_PENALTY_PCI_USING; + if (irq >= 0 && irq < ARRAY_SIZE(acpi_irq_penalty)) { + if (active) + acpi_irq_penalty[irq] += PIRQ_PENALTY_ISA_USED; + else + acpi_irq_penalty[irq] += PIRQ_PENALTY_PCI_USING; + } } /* -- GitLab From 9f497bcc695fb828da023d74ad3c966b1e58ad21 Mon Sep 17 00:00:00 2001 From: Milan Broz Date: Tue, 12 Aug 2008 17:48:27 +0200 Subject: [PATCH 391/750] ACPI: Fix thermal shutdowns Do not use unsigned int if there is test for negative number... See drivers/acpi/processor_perflib.c static unsigned int ignore_ppc = -1; ... if (event == CPUFREQ_START && ignore_ppc <= 0) { ignore_ppc = 0; ... Signed-off-by: Milan Broz Signed-off-by: Andi Kleen --- drivers/acpi/processor_perflib.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/acpi/processor_perflib.c b/drivers/acpi/processor_perflib.c index 0133af49cf0..80e32093e97 100644 --- a/drivers/acpi/processor_perflib.c +++ b/drivers/acpi/processor_perflib.c @@ -70,7 +70,7 @@ static DEFINE_MUTEX(performance_mutex); * 0 -> cpufreq low level drivers initialized -> consider _PPC values * 1 -> ignore _PPC totally -> forced by user through boot param */ -static unsigned int ignore_ppc = -1; +static int ignore_ppc = -1; module_param(ignore_ppc, uint, 0644); MODULE_PARM_DESC(ignore_ppc, "If the frequency of your machine gets wrongly" \ "limited by BIOS, this should help"); -- GitLab From 967060d00d7ab8e992963a966cd3d18156c02d55 Mon Sep 17 00:00:00 2001 From: "Darrick J. Wong" Date: Thu, 14 Aug 2008 15:43:33 -0700 Subject: [PATCH 392/750] x86, msr: fix NULL pointer deref due to msr_open on nonexistent CPUs msr_open tests for someone trying to open a device for a nonexistent CPU. However, the function always returns 0, not ret like it should, hence userspace can BUG the kernel trivially. This bug was introduced by the cdev lock_kernel pushdown patch last May. The BUG can be reproduced with these commands: # mknod fubar c 202 8 <-- pick a number less than NR_CPUS that is not the number of an online CPU # cat fubar Signed-off-by: Darrick J. Wong Signed-off-by: Ingo Molnar --- arch/x86/kernel/msr.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/msr.c b/arch/x86/kernel/msr.c index 9fd80955244..e4393808688 100644 --- a/arch/x86/kernel/msr.c +++ b/arch/x86/kernel/msr.c @@ -131,7 +131,7 @@ static int msr_open(struct inode *inode, struct file *file) ret = -EIO; /* MSR not supported */ out: unlock_kernel(); - return 0; + return ret; } /* -- GitLab From ef31023743e66de7184e9aad432291c842a6384b Mon Sep 17 00:00:00 2001 From: Dave Jones Date: Thu, 14 Aug 2008 15:07:03 -0400 Subject: [PATCH 393/750] x86: silence mmconfig printk There's so much broken mmconfig hardware/bios'es out there, that classing this as an error seems a little extreme. Lower its priority to KERN_INFO so that it isn't so noisy when booting with 'quiet' Signed-off-by: Dave Jones Signed-off-by: Ingo Molnar --- arch/x86/pci/mmconfig-shared.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/pci/mmconfig-shared.c b/arch/x86/pci/mmconfig-shared.c index 23faaa890ff..2bd5c53f638 100644 --- a/arch/x86/pci/mmconfig-shared.c +++ b/arch/x86/pci/mmconfig-shared.c @@ -365,7 +365,7 @@ static void __init pci_mmcfg_reject_broken(int early) return; reject: - printk(KERN_ERR "PCI: Not using MMCONFIG.\n"); + printk(KERN_INFO "PCI: Not using MMCONFIG.\n"); pci_mmcfg_arch_free(); kfree(pci_mmcfg_config); pci_mmcfg_config = NULL; -- GitLab From 519c31bacf78a969efa8d2e55ed8862848f28590 Mon Sep 17 00:00:00 2001 From: Joerg Roedel Date: Thu, 14 Aug 2008 19:55:15 +0200 Subject: [PATCH 394/750] x86, AMD IOMMU: use status bit instead of memory write-back for completion wait Signed-off-by: Joerg Roedel Signed-off-by: Ingo Molnar --- arch/x86/kernel/amd_iommu.c | 17 ++++++++++------- include/asm-x86/amd_iommu_types.h | 4 ++++ 2 files changed, 14 insertions(+), 7 deletions(-) diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c index 22d7d050905..028e945c68a 100644 --- a/arch/x86/kernel/amd_iommu.c +++ b/arch/x86/kernel/amd_iommu.c @@ -101,16 +101,13 @@ static int iommu_queue_command(struct amd_iommu *iommu, struct iommu_cmd *cmd) */ static int iommu_completion_wait(struct amd_iommu *iommu) { - int ret; + int ret, ready = 0; + unsigned status = 0; struct iommu_cmd cmd; - volatile u64 ready = 0; - unsigned long ready_phys = virt_to_phys(&ready); unsigned long i = 0; memset(&cmd, 0, sizeof(cmd)); - cmd.data[0] = LOW_U32(ready_phys) | CMD_COMPL_WAIT_STORE_MASK; - cmd.data[1] = upper_32_bits(ready_phys); - cmd.data[2] = 1; /* value written to 'ready' */ + cmd.data[0] = CMD_COMPL_WAIT_INT_MASK; CMD_SET_TYPE(&cmd, CMD_COMPL_WAIT); iommu->need_sync = 0; @@ -122,9 +119,15 @@ static int iommu_completion_wait(struct amd_iommu *iommu) while (!ready && (i < EXIT_LOOP_COUNT)) { ++i; - cpu_relax(); + /* wait for the bit to become one */ + status = readl(iommu->mmio_base + MMIO_STATUS_OFFSET); + ready = status & MMIO_STATUS_COM_WAIT_INT_MASK; } + /* set bit back to zero */ + status &= ~MMIO_STATUS_COM_WAIT_INT_MASK; + writel(status, iommu->mmio_base + MMIO_STATUS_OFFSET); + if (unlikely((i == EXIT_LOOP_COUNT) && printk_ratelimit())) printk(KERN_WARNING "AMD IOMMU: Completion wait loop failed\n"); diff --git a/include/asm-x86/amd_iommu_types.h b/include/asm-x86/amd_iommu_types.h index 22aa58ca199..32543229db7 100644 --- a/include/asm-x86/amd_iommu_types.h +++ b/include/asm-x86/amd_iommu_types.h @@ -69,6 +69,9 @@ #define MMIO_EVT_TAIL_OFFSET 0x2018 #define MMIO_STATUS_OFFSET 0x2020 +/* MMIO status bits */ +#define MMIO_STATUS_COM_WAIT_INT_MASK 0x04 + /* feature control bits */ #define CONTROL_IOMMU_EN 0x00ULL #define CONTROL_HT_TUN_EN 0x01ULL @@ -89,6 +92,7 @@ #define CMD_INV_IOMMU_PAGES 0x03 #define CMD_COMPL_WAIT_STORE_MASK 0x01 +#define CMD_COMPL_WAIT_INT_MASK 0x02 #define CMD_INV_IOMMU_PAGES_SIZE_MASK 0x01 #define CMD_INV_IOMMU_PAGES_PDE_MASK 0x02 -- GitLab From 9f5f5fb35d2934fe7dc0cb019854a030efd10cd7 Mon Sep 17 00:00:00 2001 From: Joerg Roedel Date: Thu, 14 Aug 2008 19:55:16 +0200 Subject: [PATCH 395/750] x86, AMD IOMMU: initialize device table properly This patch adds device table initializations which forbids memory accesses for devices per default and disables all page faults. Signed-off-by: Joerg Roedel Signed-off-by: Ingo Molnar --- arch/x86/kernel/amd_iommu_init.c | 18 ++++++++++++++++++ include/asm-x86/amd_iommu_types.h | 1 + 2 files changed, 19 insertions(+) diff --git a/arch/x86/kernel/amd_iommu_init.c b/arch/x86/kernel/amd_iommu_init.c index d9a9da597e7..ceba3381153 100644 --- a/arch/x86/kernel/amd_iommu_init.c +++ b/arch/x86/kernel/amd_iommu_init.c @@ -800,6 +800,21 @@ static int __init init_memory_definitions(struct acpi_table_header *table) return 0; } +/* + * Init the device table to not allow DMA access for devices and + * suppress all page faults + */ +static void init_device_table(void) +{ + u16 devid; + + for (devid = 0; devid <= amd_iommu_last_bdf; ++devid) { + set_dev_entry_bit(devid, DEV_ENTRY_VALID); + set_dev_entry_bit(devid, DEV_ENTRY_TRANSLATION); + set_dev_entry_bit(devid, DEV_ENTRY_NO_PAGE_FAULT); + } +} + /* * This function finally enables all IOMMUs found in the system after * they have been initialized @@ -931,6 +946,9 @@ int __init amd_iommu_init(void) if (amd_iommu_pd_alloc_bitmap == NULL) goto free; + /* init the device table */ + init_device_table(); + /* * let all alias entries point to itself */ diff --git a/include/asm-x86/amd_iommu_types.h b/include/asm-x86/amd_iommu_types.h index 32543229db7..f0beca73e36 100644 --- a/include/asm-x86/amd_iommu_types.h +++ b/include/asm-x86/amd_iommu_types.h @@ -103,6 +103,7 @@ #define DEV_ENTRY_TRANSLATION 0x01 #define DEV_ENTRY_IR 0x3d #define DEV_ENTRY_IW 0x3e +#define DEV_ENTRY_NO_PAGE_FAULT 0x62 #define DEV_ENTRY_EX 0x67 #define DEV_ENTRY_SYSMGT1 0x68 #define DEV_ENTRY_SYSMGT2 0x69 -- GitLab From 8a456695c5020d6317f9c7af190999e9414b0d3e Mon Sep 17 00:00:00 2001 From: Joerg Roedel Date: Thu, 14 Aug 2008 19:55:17 +0200 Subject: [PATCH 396/750] x86m AMD IOMMU: cleanup: replace LOW_U32 macro with generic lower_32_bits Signed-off-by: Joerg Roedel Signed-off-by: Ingo Molnar --- arch/x86/kernel/amd_iommu.c | 2 +- include/asm-x86/amd_iommu_types.h | 3 --- 2 files changed, 1 insertion(+), 4 deletions(-) diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c index 028e945c68a..de39e1f2ede 100644 --- a/arch/x86/kernel/amd_iommu.c +++ b/arch/x86/kernel/amd_iommu.c @@ -164,7 +164,7 @@ static int iommu_queue_inv_iommu_pages(struct amd_iommu *iommu, address &= PAGE_MASK; CMD_SET_TYPE(&cmd, CMD_INV_IOMMU_PAGES); cmd.data[1] |= domid; - cmd.data[2] = LOW_U32(address); + cmd.data[2] = lower_32_bits(address); cmd.data[3] = upper_32_bits(address); if (s) /* size bit - we flush more than one 4kb page */ cmd.data[2] |= CMD_INV_IOMMU_PAGES_SIZE_MASK; diff --git a/include/asm-x86/amd_iommu_types.h b/include/asm-x86/amd_iommu_types.h index f0beca73e36..dcc81206739 100644 --- a/include/asm-x86/amd_iommu_types.h +++ b/include/asm-x86/amd_iommu_types.h @@ -31,9 +31,6 @@ #define ALIAS_TABLE_ENTRY_SIZE 2 #define RLOOKUP_TABLE_ENTRY_SIZE (sizeof(void *)) -/* helper macros */ -#define LOW_U32(x) ((x) & ((1ULL << 32)-1)) - /* Length of the MMIO region for the AMD IOMMU */ #define MMIO_REGION_LENGTH 0x4000 -- GitLab From 129d6aba444d1e99d4cbfb9866a4652912426b65 Mon Sep 17 00:00:00 2001 From: Joerg Roedel Date: Thu, 14 Aug 2008 19:55:18 +0200 Subject: [PATCH 397/750] x86, AMD IOMMU: initialize dma_ops after sysfs registration If sysfs registration fails all memory used by IOMMU is freed. This happens after dma_ops initialization and the functions will access the freed memory then. Fix this by initializing dma_ops after the sysfs registration. Signed-off-by: Joerg Roedel Signed-off-by: Ingo Molnar --- arch/x86/kernel/amd_iommu_init.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/x86/kernel/amd_iommu_init.c b/arch/x86/kernel/amd_iommu_init.c index ceba3381153..a69cc0f5204 100644 --- a/arch/x86/kernel/amd_iommu_init.c +++ b/arch/x86/kernel/amd_iommu_init.c @@ -972,15 +972,15 @@ int __init amd_iommu_init(void) if (acpi_table_parse("IVRS", init_memory_definitions) != 0) goto free; - ret = amd_iommu_init_dma_ops(); + ret = sysdev_class_register(&amd_iommu_sysdev_class); if (ret) goto free; - ret = sysdev_class_register(&amd_iommu_sysdev_class); + ret = sysdev_register(&device_amd_iommu); if (ret) goto free; - ret = sysdev_register(&device_amd_iommu); + ret = amd_iommu_init_dma_ops(); if (ret) goto free; -- GitLab From dcc984166870150709f0c645b521a47becd9a047 Mon Sep 17 00:00:00 2001 From: Aristeu Rozanski Date: Thu, 14 Aug 2008 16:32:15 -0400 Subject: [PATCH 398/750] x86, perfctr: don't use CCCR_OVF_PMI1 on Pentium 4Ds Currently, setup_p4_watchdog() use CCCR_OVF_PMI1 to enable the counter overflow interrupts to the second logical core. But this bit doesn't work on Pentium 4 Ds (model 4, stepping 4) and this patch avoids its use on these processors. Tested on 4 different machines that have this specific model with success. Signed-off-by: Aristeu Rozanski Cc: jvillalovos@redhat.com Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/perfctr-watchdog.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/arch/x86/kernel/cpu/perfctr-watchdog.c b/arch/x86/kernel/cpu/perfctr-watchdog.c index de7439f82b9..05cc22dbd4f 100644 --- a/arch/x86/kernel/cpu/perfctr-watchdog.c +++ b/arch/x86/kernel/cpu/perfctr-watchdog.c @@ -478,7 +478,13 @@ static int setup_p4_watchdog(unsigned nmi_hz) perfctr_msr = MSR_P4_IQ_PERFCTR1; evntsel_msr = MSR_P4_CRU_ESCR0; cccr_msr = MSR_P4_IQ_CCCR1; - cccr_val = P4_CCCR_OVF_PMI1 | P4_CCCR_ESCR_SELECT(4); + + /* Pentium 4 D processors don't support P4_CCCR_OVF_PMI1 */ + if (boot_cpu_data.x86_model == 4 && boot_cpu_data.x86_mask == 4) + cccr_val = P4_CCCR_OVF_PMI0; + else + cccr_val = P4_CCCR_OVF_PMI1; + cccr_val |= P4_CCCR_ESCR_SELECT(4); } evntsel = P4_ESCR_EVENT_SELECT(0x3F) -- GitLab From 394a15051c33f2b18e72f42283b36a9388fa414b Mon Sep 17 00:00:00 2001 From: Mark Langsdorf Date: Thu, 14 Aug 2008 09:11:26 -0500 Subject: [PATCH 399/750] x86: invalidate caches before going into suspend MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit When a CPU core is shut down, all of its caches need to be flushed to prevent stale data from causing errors if the core is resumed. Current Linux suspend code performs an assignment after the flush, which can add dirty data back to the cache.  On some AMD platforms, additional speculative reads have caused crashes on resume because of this dirty data. Relocate the cache flush to be the very last thing done before halting.  Tie into an assembly line so the compile will not reorder it.  Add some documentation explaining what is going on and why we're doing this. Signed-off-by: Mark Langsdorf Acked-by: Mark Borden Acked-by: Michael Hohmuth Signed-off-by: Ingo Molnar --- arch/x86/kernel/process_32.c | 5 ++--- arch/x86/kernel/process_64.c | 5 ++--- include/asm-x86/processor.h | 23 +++++++++++++++++++++++ 3 files changed, 27 insertions(+), 6 deletions(-) diff --git a/arch/x86/kernel/process_32.c b/arch/x86/kernel/process_32.c index 53bc653ed5c..3b7a1ddcc0b 100644 --- a/arch/x86/kernel/process_32.c +++ b/arch/x86/kernel/process_32.c @@ -95,7 +95,6 @@ static inline void play_dead(void) { /* This must be done before dead CPU ack */ cpu_exit_clear(); - wbinvd(); mb(); /* Ack it */ __get_cpu_var(cpu_state) = CPU_DEAD; @@ -104,8 +103,8 @@ static inline void play_dead(void) * With physical CPU hotplug, we should halt the cpu */ local_irq_disable(); - while (1) - halt(); + /* mask all interrupts, flush any and all caches, and halt */ + wbinvd_halt(); } #else static inline void play_dead(void) diff --git a/arch/x86/kernel/process_64.c b/arch/x86/kernel/process_64.c index 3fb62a7d9a1..71553b664e2 100644 --- a/arch/x86/kernel/process_64.c +++ b/arch/x86/kernel/process_64.c @@ -93,14 +93,13 @@ DECLARE_PER_CPU(int, cpu_state); static inline void play_dead(void) { idle_task_exit(); - wbinvd(); mb(); /* Ack it */ __get_cpu_var(cpu_state) = CPU_DEAD; local_irq_disable(); - while (1) - halt(); + /* mask all interrupts, flush any and all caches, and halt */ + wbinvd_halt(); } #else static inline void play_dead(void) diff --git a/include/asm-x86/processor.h b/include/asm-x86/processor.h index 5f58da401b4..4df3e2f6fb5 100644 --- a/include/asm-x86/processor.h +++ b/include/asm-x86/processor.h @@ -728,6 +728,29 @@ extern unsigned long boot_option_idle_override; extern unsigned long idle_halt; extern unsigned long idle_nomwait; +/* + * on systems with caches, caches must be flashed as the absolute + * last instruction before going into a suspended halt. Otherwise, + * dirty data can linger in the cache and become stale on resume, + * leading to strange errors. + * + * perform a variety of operations to guarantee that the compiler + * will not reorder instructions. wbinvd itself is serializing + * so the processor will not reorder. + * + * Systems without cache can just go into halt. + */ +static inline void wbinvd_halt(void) +{ + mb(); + /* check for clflush to determine if wbinvd is legal */ + if (cpu_has_clflush) + asm volatile("cli; wbinvd; 1: hlt; jmp 1b" : : : "memory"); + else + while (1) + halt(); +} + extern void enable_sep_cpu(void); extern int sysenter_setup(void); -- GitLab From 04b69447f79eade34e92f3117a39e8fa6ecb519b Mon Sep 17 00:00:00 2001 From: Pavel Machek Date: Thu, 14 Aug 2008 17:16:50 +0200 Subject: [PATCH 400/750] arch/x86/Kconfig: clean up, experimental adjustement Adjust experimental tags in Kconfig, update config to notice that i386/x86_64 is now single architecture. Signed-off-by: Pavel Machek Signed-off-by: Ingo Molnar --- arch/x86/Kconfig | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index ac2fb0641a0..68d91c8233f 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -951,9 +951,9 @@ config NUMA local memory controller of the CPU and add some more NUMA awareness to the kernel. - For i386 this is currently highly experimental and should be only + For 32-bit this is currently highly experimental and should be only used for kernel development. It might also cause boot failures. - For x86_64 this is recommended on all multiprocessor Opteron systems. + For 64-bit this is recommended on all multiprocessor Opteron systems. If the system is EM64T, you should say N unless your system is EM64T NUMA. @@ -1263,7 +1263,7 @@ config KEXEC strongly in flux, so no good recommendation can be made. config CRASH_DUMP - bool "kernel crash dumps (EXPERIMENTAL)" + bool "kernel crash dumps" depends on X86_64 || (X86_32 && HIGHMEM) help Generate crash dump after being started by kexec. -- GitLab From 1c5b0eb66d74683e2be5da0c53e33c1f4ca982fd Mon Sep 17 00:00:00 2001 From: Mikael Pettersson Date: Wed, 13 Aug 2008 21:07:07 +0200 Subject: [PATCH 401/750] x86: fix readb() et al compile error with gcc-3.2.3 Building 2.6.27-rc1 on x86 with gcc-3.2.3 fails with: In file included from include/asm/dma.h:12, from include/linux/bootmem.h:8, from init/main.c:26: include/asm/io.h: In function `readb': include/asm/io.h:32: syntax error before string constant include/asm/io.h: In function `readw': include/asm/io.h:33: syntax error before string constant include/asm/io.h: In function `readl': include/asm/io.h:34: syntax error before string constant include/asm/io.h: In function `__readb': include/asm/io.h:36: syntax error before string constant include/asm/io.h: In function `__readw': include/asm/io.h:37: syntax error before string constant include/asm/io.h: In function `__readl': include/asm/io.h:38: syntax error before string constant make[1]: *** [init/main.o] Error 1 make: *** [init] Error 2 Starting with 2.6.27-rc1 readb() et al are generated by a build_mmio_read() macro, which generates asm() statements with output register constraints like "=" "q", i.e. as two adjacent string literals. This doesn't work with gcc-3.2.3. Fixed by moving the "=" part into the callers' reg parameter (as suggested by Ingo). Build and boot-tested with gcc-3.2.3 on 32 and 64-bit x86. Fixes . Signed-off-by: Mikael Pettersson Signed-off-by: Ingo Molnar --- include/asm-x86/io.h | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-) diff --git a/include/asm-x86/io.h b/include/asm-x86/io.h index bf5d629b3a3..0f954dc89cb 100644 --- a/include/asm-x86/io.h +++ b/include/asm-x86/io.h @@ -21,7 +21,7 @@ extern void __iomem *fix_ioremap(unsigned idx, unsigned long phys); #define build_mmio_read(name, size, type, reg, barrier) \ static inline type name(const volatile void __iomem *addr) \ -{ type ret; asm volatile("mov" size " %1,%0":"=" reg (ret) \ +{ type ret; asm volatile("mov" size " %1,%0":reg (ret) \ :"m" (*(volatile type __force *)addr) barrier); return ret; } #define build_mmio_write(name, size, type, reg, barrier) \ @@ -29,13 +29,13 @@ static inline void name(type val, volatile void __iomem *addr) \ { asm volatile("mov" size " %0,%1": :reg (val), \ "m" (*(volatile type __force *)addr) barrier); } -build_mmio_read(readb, "b", unsigned char, "q", :"memory") -build_mmio_read(readw, "w", unsigned short, "r", :"memory") -build_mmio_read(readl, "l", unsigned int, "r", :"memory") +build_mmio_read(readb, "b", unsigned char, "=q", :"memory") +build_mmio_read(readw, "w", unsigned short, "=r", :"memory") +build_mmio_read(readl, "l", unsigned int, "=r", :"memory") -build_mmio_read(__readb, "b", unsigned char, "q", ) -build_mmio_read(__readw, "w", unsigned short, "r", ) -build_mmio_read(__readl, "l", unsigned int, "r", ) +build_mmio_read(__readb, "b", unsigned char, "=q", ) +build_mmio_read(__readw, "w", unsigned short, "=r", ) +build_mmio_read(__readl, "l", unsigned int, "=r", ) build_mmio_write(writeb, "b", unsigned char, "q", :"memory") build_mmio_write(writew, "w", unsigned short, "r", :"memory") @@ -59,8 +59,8 @@ build_mmio_write(__writel, "l", unsigned int, "r", ) #define mmiowb() barrier() #ifdef CONFIG_X86_64 -build_mmio_read(readq, "q", unsigned long, "r", :"memory") -build_mmio_read(__readq, "q", unsigned long, "r", ) +build_mmio_read(readq, "q", unsigned long, "=r", :"memory") +build_mmio_read(__readq, "q", unsigned long, "=r", ) build_mmio_write(writeq, "q", unsigned long, "r", :"memory") build_mmio_write(__writeq, "q", unsigned long, "r", ) -- GitLab From a06de63000b95e1ed1c6373a72376876c952608e Mon Sep 17 00:00:00 2001 From: Hugh Dickins Date: Fri, 15 Aug 2008 13:58:32 +0100 Subject: [PATCH 402/750] x86: fix /proc/meminfo DirectMap Do we actually want these DirectMap lines in the x86 /proc/meminfo? I can see they're interesting to CPA developers and TLB optimizers, but they don't fit its usual "where has all my memory gone?" usage. If they are to stay, here are some fixes. 1. On x86_32 without PAE, they're not 2M but 4M pages: no need to mess with the internal enum, but show the right name to users. 2. Many machines can never show anything but 0 for DirectMap1G, so suppress that line unless direct_gbpages are really enabled. 3. The unit in /proc/meminfo is kB not number of pages: HugePages messed that up, but they're an example to regret not to follow. 4. Once we use kB, it's easy to see that 1GB has gone missing (which explains why CONFIG_CPA_DEBUG=y soon wraps DirectMap2M negative): because head_64.S's level2_ident_pgt entries were not counted. My fix is not ideal, but works for more and for less than 1G, and avoids interfering with early bootup pagetable contortions. Signed-off-by: Hugh Dickins Cc: Andi Kleen Signed-off-by: Ingo Molnar --- arch/x86/mm/init_64.c | 6 +++++- arch/x86/mm/pageattr.c | 18 ++++++++++++------ 2 files changed, 17 insertions(+), 7 deletions(-) diff --git a/arch/x86/mm/init_64.c b/arch/x86/mm/init_64.c index 129618ca0ea..b3e6c3075ac 100644 --- a/arch/x86/mm/init_64.c +++ b/arch/x86/mm/init_64.c @@ -60,7 +60,7 @@ static unsigned long dma_reserve __initdata; DEFINE_PER_CPU(struct mmu_gather, mmu_gathers); -int direct_gbpages __meminitdata +int direct_gbpages #ifdef CONFIG_DIRECT_GBPAGES = 1 #endif @@ -314,6 +314,7 @@ phys_pmd_init(pmd_t *pmd_page, unsigned long address, unsigned long end, { unsigned long pages = 0; unsigned long last_map_addr = end; + unsigned long start = address; int i = pmd_index(address); @@ -334,6 +335,9 @@ phys_pmd_init(pmd_t *pmd_page, unsigned long address, unsigned long end, if (!pmd_large(*pmd)) last_map_addr = phys_pte_update(pmd, address, end); + /* Count entries we're using from level2_ident_pgt */ + if (start == 0) + pages++; continue; } diff --git a/arch/x86/mm/pageattr.c b/arch/x86/mm/pageattr.c index ba24537d69d..f5f5154ea11 100644 --- a/arch/x86/mm/pageattr.c +++ b/arch/x86/mm/pageattr.c @@ -55,13 +55,19 @@ static void split_page_count(int level) int arch_report_meminfo(char *page) { - int n = sprintf(page, "DirectMap4k: %8lu\n" - "DirectMap2M: %8lu\n", - direct_pages_count[PG_LEVEL_4K], - direct_pages_count[PG_LEVEL_2M]); + int n = sprintf(page, "DirectMap4k: %8lu kB\n", + direct_pages_count[PG_LEVEL_4K] << 2); +#if defined(CONFIG_X86_64) || defined(CONFIG_X86_PAE) + n += sprintf(page + n, "DirectMap2M: %8lu kB\n", + direct_pages_count[PG_LEVEL_2M] << 11); +#else + n += sprintf(page + n, "DirectMap4M: %8lu kB\n", + direct_pages_count[PG_LEVEL_2M] << 12); +#endif #ifdef CONFIG_X86_64 - n += sprintf(page + n, "DirectMap1G: %8lu\n", - direct_pages_count[PG_LEVEL_1G]); + if (direct_gbpages) + n += sprintf(page + n, "DirectMap1G: %8lu kB\n", + direct_pages_count[PG_LEVEL_1G] << 20); #endif return n; } -- GitLab From 15636668449d4135ac77a79715ba430a81aed16d Mon Sep 17 00:00:00 2001 From: Aristeu Rozanski Date: Fri, 15 Aug 2008 08:36:14 -0400 Subject: [PATCH 403/750] x86, NMI: fix watchdog failure message > it just won't work at boot time - the second logic unit will be stuck: > > Booting processor 1/2 APIC 0x1 > Initializing CPU#1 > Calibrating delay using timer specific routine.. 5586.12 BogoMIPS (lpj=2793063) > CPU: Trace cache: 12K uops, L1 D cache: 16K > CPU: L2 cache: 1024K > CPU: Physical Processor ID: 0 > CPU: Processor Core ID: 1 > CPU1: Thermal monitoring enabled (TM1) > Intel(R) Pentium(R) D CPU 2.80GHz stepping 04 > Brought up 2 CPUs > testing NMI watchdog ... <4>WARNING: CPU#1: NMI appears to be stuck (0->0)! while at it... - fix that newline Signed-off-by: Aristeu Rozanski Cc: jvillalo@redhat.com Signed-off-by: Ingo Molnar --- arch/x86/kernel/nmi.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/x86/kernel/nmi.c b/arch/x86/kernel/nmi.c index ac6d51222e7..919473ad4a2 100644 --- a/arch/x86/kernel/nmi.c +++ b/arch/x86/kernel/nmi.c @@ -142,11 +142,15 @@ int __init check_nmi_watchdog(void) if (!per_cpu(wd_enabled, cpu)) continue; if (get_nmi_count(cpu) - prev_nmi_count[cpu] <= 5) { + printk("\n"); printk(KERN_WARNING "WARNING: CPU#%d: NMI " "appears to be stuck (%d->%d)!\n", cpu, prev_nmi_count[cpu], get_nmi_count(cpu)); + printk(KERN_WARNING "Please report this to " + "linux-kernel@vger.kernel.org and attach " + "the output of 'dmesg' command.\n"); per_cpu(wd_enabled, cpu) = 0; atomic_dec(&nmi_active); } -- GitLab From 8bb851900f5d0a79d3fddac808cc670d9894ef67 Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Fri, 15 Aug 2008 15:34:32 +0200 Subject: [PATCH 404/750] x86, nmi: clean UP NMI watchdog failure message clean up the failure message - and redirect people to bugzilla instead of lkml. Signed-off-by: Ingo Molnar --- arch/x86/kernel/nmi.c | 32 +++++++++++++++++++------------- 1 file changed, 19 insertions(+), 13 deletions(-) diff --git a/arch/x86/kernel/nmi.c b/arch/x86/kernel/nmi.c index 919473ad4a2..abb78a2cc4a 100644 --- a/arch/x86/kernel/nmi.c +++ b/arch/x86/kernel/nmi.c @@ -114,6 +114,23 @@ static __init void nmi_cpu_busy(void *data) } #endif +static void report_broken_nmi(int cpu, int *prev_nmi_count) +{ + printk(KERN_CONT "\n"); + + printk(KERN_WARNING + "WARNING: CPU#%d: NMI appears to be stuck (%d->%d)!\n", + cpu, prev_nmi_count[cpu], get_nmi_count(cpu)); + + printk(KERN_WARNING + "Please report this to bugzilla.kernel.org,\n"); + printk(KERN_WARNING + "and attach the output of the 'dmesg' command.\n"); + + per_cpu(wd_enabled, cpu) = 0; + atomic_dec(&nmi_active); +} + int __init check_nmi_watchdog(void) { unsigned int *prev_nmi_count; @@ -141,19 +158,8 @@ int __init check_nmi_watchdog(void) for_each_online_cpu(cpu) { if (!per_cpu(wd_enabled, cpu)) continue; - if (get_nmi_count(cpu) - prev_nmi_count[cpu] <= 5) { - printk("\n"); - printk(KERN_WARNING "WARNING: CPU#%d: NMI " - "appears to be stuck (%d->%d)!\n", - cpu, - prev_nmi_count[cpu], - get_nmi_count(cpu)); - printk(KERN_WARNING "Please report this to " - "linux-kernel@vger.kernel.org and attach " - "the output of 'dmesg' command.\n"); - per_cpu(wd_enabled, cpu) = 0; - atomic_dec(&nmi_active); - } + if (get_nmi_count(cpu) - prev_nmi_count[cpu] <= 5) + report_broken_nmi(cpu, prev_nmi_count); } endflag = 1; if (!atomic_read(&nmi_active)) { -- GitLab From 7bc069c6bc4ede519a7116be1b9e149a1dbf787a Mon Sep 17 00:00:00 2001 From: Jan Beulich Date: Mon, 4 Aug 2008 14:38:54 +0100 Subject: [PATCH 405/750] x86: fix spin_is_contended() The masked difference is what needs to be compared against 1, rather than the difference of masked values (which can be negative). Signed-off-by: Jan Beulich Acked-by: Nick Piggin Cc: Signed-off-by: Ingo Molnar --- include/asm-x86/spinlock.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/include/asm-x86/spinlock.h b/include/asm-x86/spinlock.h index 4f9a9861799..e39c790dbfd 100644 --- a/include/asm-x86/spinlock.h +++ b/include/asm-x86/spinlock.h @@ -65,7 +65,7 @@ static inline int __ticket_spin_is_contended(raw_spinlock_t *lock) { int tmp = ACCESS_ONCE(lock->slock); - return (((tmp >> 8) & 0xff) - (tmp & 0xff)) > 1; + return (((tmp >> 8) - tmp) & 0xff) > 1; } static __always_inline void __ticket_spin_lock(raw_spinlock_t *lock) @@ -127,7 +127,7 @@ static inline int __ticket_spin_is_contended(raw_spinlock_t *lock) { int tmp = ACCESS_ONCE(lock->slock); - return (((tmp >> 16) & 0xffff) - (tmp & 0xffff)) > 1; + return (((tmp >> 16) - tmp) & 0xffff) > 1; } static __always_inline void __ticket_spin_lock(raw_spinlock_t *lock) -- GitLab From 9744f5a32853642f8ed0749a1c9ed8cf9c9c9dc4 Mon Sep 17 00:00:00 2001 From: Marcin Slusarz Date: Sun, 3 Aug 2008 19:25:48 +0200 Subject: [PATCH 406/750] x86, acpi: cleanup, temp_stack is used only when CONFIG_SMP is set fix: arch/x86/kernel/acpi/sleep.c:24: warning: 'temp_stack' defined but not used [ Sven Wegener : fix build bug ] Signed-off-by: Marcin Slusarz Acked-by: Pavel Machek Signed-off-by: Ingo Molnar --- arch/x86/kernel/acpi/sleep.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/acpi/sleep.c b/arch/x86/kernel/acpi/sleep.c index fa2161d5003..81e5ab6542d 100644 --- a/arch/x86/kernel/acpi/sleep.c +++ b/arch/x86/kernel/acpi/sleep.c @@ -20,7 +20,7 @@ unsigned long acpi_realmode_flags; /* address in low memory of the wakeup routine. */ static unsigned long acpi_realmode; -#ifdef CONFIG_64BIT +#if defined(CONFIG_SMP) && defined(CONFIG_64BIT) static char temp_stack[10240]; #endif -- GitLab From 0d5cdc97e242a5589e5dca23277675f4b4482490 Mon Sep 17 00:00:00 2001 From: Jens Rottmann Date: Mon, 4 Aug 2008 14:40:16 +0200 Subject: [PATCH 407/750] x86, geode-mfgpt: check IRQ before using MFGPT as clocksource Adds a simple IRQ autodetection to the AMD Geode MFGPT driver, and more importantly, adds some checks, if IRQs can actually be received on the chosen line. This fixes cases where MFGPT is selected as clocksource though not producing any ticks, so the kernel simply starves during boot. Signed-off-by: Jens Rottmann Cc: Andres Salomon Cc: linux-geode@bombadil.infradead.org Cc: Jordan Crouse Signed-off-by: Ingo Molnar --- arch/x86/kernel/mfgpt_32.c | 52 +++++++++++++++++++++++++++----------- include/asm-x86/geode.h | 3 ++- 2 files changed, 39 insertions(+), 16 deletions(-) diff --git a/arch/x86/kernel/mfgpt_32.c b/arch/x86/kernel/mfgpt_32.c index 07c0f828f48..3b599518c32 100644 --- a/arch/x86/kernel/mfgpt_32.c +++ b/arch/x86/kernel/mfgpt_32.c @@ -33,6 +33,8 @@ #include #include +#define MFGPT_DEFAULT_IRQ 7 + static struct mfgpt_timer_t { unsigned int avail:1; } mfgpt_timers[MFGPT_MAX_TIMERS]; @@ -157,29 +159,48 @@ int geode_mfgpt_toggle_event(int timer, int cmp, int event, int enable) } EXPORT_SYMBOL_GPL(geode_mfgpt_toggle_event); -int geode_mfgpt_set_irq(int timer, int cmp, int irq, int enable) +int geode_mfgpt_set_irq(int timer, int cmp, int *irq, int enable) { - u32 val, dummy; - int offset; + u32 zsel, lpc, dummy; + int shift; if (timer < 0 || timer >= MFGPT_MAX_TIMERS) return -EIO; - if (geode_mfgpt_toggle_event(timer, cmp, MFGPT_EVENT_IRQ, enable)) + /* + * Unfortunately, MFGPTs come in pairs sharing their IRQ lines. If VSA + * is using the same CMP of the timer's Siamese twin, the IRQ is set to + * 2, and we mustn't use nor change it. + * XXX: Likewise, 2 Linux drivers might clash if the 2nd overwrites the + * IRQ of the 1st. This can only happen if forcing an IRQ, calling this + * with *irq==0 is safe. Currently there _are_ no 2 drivers. + */ + rdmsr(MSR_PIC_ZSEL_LOW, zsel, dummy); + shift = ((cmp == MFGPT_CMP1 ? 0 : 4) + timer % 4) * 4; + if (((zsel >> shift) & 0xF) == 2) return -EIO; - rdmsr(MSR_PIC_ZSEL_LOW, val, dummy); + /* Choose IRQ: if none supplied, keep IRQ already set or use default */ + if (!*irq) + *irq = (zsel >> shift) & 0xF; + if (!*irq) + *irq = MFGPT_DEFAULT_IRQ; - offset = (timer % 4) * 4; - - val &= ~((0xF << offset) | (0xF << (offset + 16))); + /* Can't use IRQ if it's 0 (=disabled), 2, or routed to LPC */ + if (*irq < 1 || *irq == 2 || *irq > 15) + return -EIO; + rdmsr(MSR_PIC_IRQM_LPC, lpc, dummy); + if (lpc & (1 << *irq)) + return -EIO; + /* All chosen and checked - go for it */ + if (geode_mfgpt_toggle_event(timer, cmp, MFGPT_EVENT_IRQ, enable)) + return -EIO; if (enable) { - val |= (irq & 0x0F) << (offset); - val |= (irq & 0x0F) << (offset + 16); + zsel = (zsel & ~(0xF << shift)) | (*irq << shift); + wrmsr(MSR_PIC_ZSEL_LOW, zsel, dummy); } - wrmsr(MSR_PIC_ZSEL_LOW, val, dummy); return 0; } @@ -242,7 +263,7 @@ EXPORT_SYMBOL_GPL(geode_mfgpt_alloc_timer); static unsigned int mfgpt_tick_mode = CLOCK_EVT_MODE_SHUTDOWN; static u16 mfgpt_event_clock; -static int irq = 7; +static int irq; static int __init mfgpt_setup(char *str) { get_option(&str, &irq); @@ -346,7 +367,7 @@ int __init mfgpt_timer_setup(void) mfgpt_event_clock = timer; /* Set up the IRQ on the MFGPT side */ - if (geode_mfgpt_setup_irq(mfgpt_event_clock, MFGPT_CMP2, irq)) { + if (geode_mfgpt_setup_irq(mfgpt_event_clock, MFGPT_CMP2, &irq)) { printk(KERN_ERR "mfgpt-timer: Could not set up IRQ %d\n", irq); return -EIO; } @@ -374,13 +395,14 @@ int __init mfgpt_timer_setup(void) &mfgpt_clockevent); printk(KERN_INFO - "mfgpt-timer: registering the MFGPT timer as a clock event.\n"); + "mfgpt-timer: Registering MFGPT timer %d as a clock event, using IRQ %d\n", + timer, irq); clockevents_register_device(&mfgpt_clockevent); return 0; err: - geode_mfgpt_release_irq(mfgpt_event_clock, MFGPT_CMP2, irq); + geode_mfgpt_release_irq(mfgpt_event_clock, MFGPT_CMP2, &irq); printk(KERN_ERR "mfgpt-timer: Unable to set up the MFGPT clock source\n"); return -EIO; diff --git a/include/asm-x86/geode.h b/include/asm-x86/geode.h index bb06027fc83..2c1cda0b8a8 100644 --- a/include/asm-x86/geode.h +++ b/include/asm-x86/geode.h @@ -50,6 +50,7 @@ extern int geode_get_dev_base(unsigned int dev); #define MSR_PIC_YSEL_HIGH 0x51400021 #define MSR_PIC_ZSEL_LOW 0x51400022 #define MSR_PIC_ZSEL_HIGH 0x51400023 +#define MSR_PIC_IRQM_LPC 0x51400025 #define MSR_MFGPT_IRQ 0x51400028 #define MSR_MFGPT_NR 0x51400029 @@ -237,7 +238,7 @@ static inline u16 geode_mfgpt_read(int timer, u16 reg) } extern int geode_mfgpt_toggle_event(int timer, int cmp, int event, int enable); -extern int geode_mfgpt_set_irq(int timer, int cmp, int irq, int enable); +extern int geode_mfgpt_set_irq(int timer, int cmp, int *irq, int enable); extern int geode_mfgpt_alloc_timer(int timer, int domain); #define geode_mfgpt_setup_irq(t, c, i) geode_mfgpt_set_irq((t), (c), (i), 1) -- GitLab From 66d4bdf22b8652cda215e2653c8bbec7a767ed57 Mon Sep 17 00:00:00 2001 From: Jan Beulich Date: Thu, 31 Jul 2008 16:48:31 +0100 Subject: [PATCH 408/750] x86-64: fix overlap of modules and fixmap areas Plus add a build time check so this doesn't go unnoticed again. Signed-off-by: Jan Beulich Signed-off-by: Ingo Molnar --- arch/x86/kernel/head64.c | 1 + include/asm-x86/pgtable_64.h | 2 +- 2 files changed, 2 insertions(+), 1 deletion(-) diff --git a/arch/x86/kernel/head64.c b/arch/x86/kernel/head64.c index 1b318e903bf..9bfc4d72fb2 100644 --- a/arch/x86/kernel/head64.c +++ b/arch/x86/kernel/head64.c @@ -88,6 +88,7 @@ void __init x86_64_start_kernel(char * real_mode_data) BUILD_BUG_ON(!(MODULES_VADDR > __START_KERNEL)); BUILD_BUG_ON(!(((MODULES_END - 1) & PGDIR_MASK) == (__START_KERNEL & PGDIR_MASK))); + BUILD_BUG_ON(__fix_to_virt(__end_of_fixed_addresses) <= MODULES_END); /* clear bss before set_intr_gate with early_idt_handler */ clear_bss(); diff --git a/include/asm-x86/pgtable_64.h b/include/asm-x86/pgtable_64.h index ac5fff4cc58..549144d03d9 100644 --- a/include/asm-x86/pgtable_64.h +++ b/include/asm-x86/pgtable_64.h @@ -151,7 +151,7 @@ static inline void native_pgd_clear(pgd_t *pgd) #define VMALLOC_END _AC(0xffffe1ffffffffff, UL) #define VMEMMAP_START _AC(0xffffe20000000000, UL) #define MODULES_VADDR _AC(0xffffffffa0000000, UL) -#define MODULES_END _AC(0xfffffffffff00000, UL) +#define MODULES_END _AC(0xffffffffff000000, UL) #define MODULES_LEN (MODULES_END - MODULES_VADDR) #ifndef __ASSEMBLY__ -- GitLab From 627240aaa92a4dc00d25584910b5f205e963747b Mon Sep 17 00:00:00 2001 From: Mikulas Patocka Date: Fri, 15 Aug 2008 00:40:17 -0700 Subject: [PATCH 409/750] bootmem allocator: alloc_bootmem_core(): page-align the end offset This is the minimal sequence that jams the allocator: void *p, *q, *r; p = alloc_bootmem(PAGE_SIZE); q = alloc_bootmem(64); free_bootmem(p, PAGE_SIZE); p = alloc_bootmem(PAGE_SIZE); r = alloc_bootmem(64); after this sequence (assuming that the allocator was empty or page-aligned before), pointer "q" will be equal to pointer "r". What's hapenning inside the allocator: p = alloc_bootmem(PAGE_SIZE); in allocator: last_end_off == PAGE_SIZE, bitmap contains bits 10000... q = alloc_bootmem(64); in allocator: last_end_off == PAGE_SIZE + 64, bitmap contains 11000... free_bootmem(p, PAGE_SIZE); in allocator: last_end_off == PAGE_SIZE + 64, bitmap contains 01000... p = alloc_bootmem(PAGE_SIZE); in allocator: last_end_off == PAGE_SIZE, bitmap contains 11000... r = alloc_bootmem(64); and now: it finds bit "2", as a place where to allocate (sidx) it hits the condition if (bdata->last_end_off && PFN_DOWN(bdata->last_end_off) + 1 == sidx)) start_off = ALIGN(bdata->last_end_off, align); -you can see that the condition is true, so it assigns start_off = ALIGN(bdata->last_end_off, align); (that is PAGE_SIZE) and allocates over already allocated block. With the patch it tries to continue at the end of previous allocation only if the previous allocation ended in the middle of the page. Signed-off-by: Mikulas Patocka Acked-by: Johannes Weiner Cc: David Miller Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- mm/bootmem.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/mm/bootmem.c b/mm/bootmem.c index 4af15d0340a..e023c68b025 100644 --- a/mm/bootmem.c +++ b/mm/bootmem.c @@ -473,7 +473,7 @@ find_block: goto find_block; } - if (bdata->last_end_off && + if (bdata->last_end_off & (PAGE_SIZE - 1) && PFN_DOWN(bdata->last_end_off) + 1 == sidx) start_off = ALIGN(bdata->last_end_off, align); else -- GitLab From 6acb2eceff80027bd67a204227c6c8effd464c25 Mon Sep 17 00:00:00 2001 From: Michael Kerrisk Date: Fri, 15 Aug 2008 00:40:18 -0700 Subject: [PATCH 410/750] Documentation/vm/page_migration: update reference to numa_maps + fix download URI With man-pages-3.07, the numa_maps documentation home is now proc(5), so the reference in Documentation/vm/page_migration needs updating. (Cliff/Lee are removing numa_maps.5 from the numactl package.) Also, the download location for the numactl package changed a while back. This patch fixes both things, as well as a typo (provided-->provides). Signed-off-by: Michael Kerrisk Cc: Cliff Wickman Cc: Lee Schermerhorn Cc: Randy Dunlap Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/vm/page_migration | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) diff --git a/Documentation/vm/page_migration b/Documentation/vm/page_migration index 99f89aa1016..d5fdfd34bba 100644 --- a/Documentation/vm/page_migration +++ b/Documentation/vm/page_migration @@ -18,10 +18,11 @@ migrate_pages function call takes two sets of nodes and moves pages of a process that are located on the from nodes to the destination nodes. Page migration functions are provided by the numactl package by Andi Kleen (a version later than 0.9.3 is required. Get it from -ftp://ftp.suse.com/pub/people/ak). numactl provided libnuma which -provides an interface similar to other numa functionality for page migration. -cat /proc//numa_maps allows an easy review of where the pages of -a process are located. See also the numa_maps manpage in the numactl package. +ftp://oss.sgi.com/www/projects/libnuma/download/). numactl provides libnuma +which provides an interface similar to other numa functionality for page +migration. cat /proc//numa_maps allows an easy review of where the +pages of a process are located. See also the numa_maps documentation in the +proc(5) man page. Manual migration is useful if for example the scheduler has relocated a process to a processor on a distant node. A batch scheduler or an -- GitLab From ce289e89726948b50a58c9e8f4e81174a8c9c254 Mon Sep 17 00:00:00 2001 From: Marcin Slusarz Date: Fri, 15 Aug 2008 00:40:19 -0700 Subject: [PATCH 411/750] suspend: fix section mismatch warning - register_nosave_region WARNING: vmlinux.o(.text+0xe684): Section mismatch in reference from the function register_nosave_region() to the function .init.text:__register_nosave_region() The function register_nosave_region() references the function __init __register_nosave_region(). This is often because register_nosave_region lacks a __init annotation or the annotation of __register_nosave_region is wrong. register_nosave_region calls __init function and is called only from __init functions Signed-off-by: Marcin Slusarz Acked-by: Rafael J. Wysocki Cc: Pavel Machek Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- include/linux/suspend.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/include/linux/suspend.h b/include/linux/suspend.h index c6343509597..2ce8207686e 100644 --- a/include/linux/suspend.h +++ b/include/linux/suspend.h @@ -217,11 +217,11 @@ struct platform_hibernation_ops { #ifdef CONFIG_HIBERNATION /* kernel/power/snapshot.c */ extern void __register_nosave_region(unsigned long b, unsigned long e, int km); -static inline void register_nosave_region(unsigned long b, unsigned long e) +static inline void __init register_nosave_region(unsigned long b, unsigned long e) { __register_nosave_region(b, e, 0); } -static inline void register_nosave_region_late(unsigned long b, unsigned long e) +static inline void __init register_nosave_region_late(unsigned long b, unsigned long e) { __register_nosave_region(b, e, 1); } -- GitLab From 4cd69b986ebf0f8da93f82ffbb89c032ee09c2e1 Mon Sep 17 00:00:00 2001 From: Huang Ying Date: Fri, 15 Aug 2008 00:40:20 -0700 Subject: [PATCH 412/750] kexec: fix compilation warning on xchg(&kexec_lock, 0) in kernel_kexec() kernel/kexec.c: In function 'kernel_kexec': kernel/kexec.c:1506: warning: value computed is not used Signed-off-by: Huang Ying Cc: "Eric W. Biederman" Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- kernel/kexec.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/kernel/kexec.c b/kernel/kexec.c index c8a4370e2a3..cf3797b7678 100644 --- a/kernel/kexec.c +++ b/kernel/kexec.c @@ -1503,7 +1503,8 @@ int kernel_kexec(void) } Unlock: - xchg(&kexec_lock, 0); + if (!xchg(&kexec_lock, 0)) + BUG(); return error; } -- GitLab From 7ade3fcc1fe2801336112027a884070c9ca451af Mon Sep 17 00:00:00 2001 From: Huang Ying Date: Fri, 15 Aug 2008 00:40:21 -0700 Subject: [PATCH 413/750] kexec jump: clean up #ifdef and comments Move if (kexec_image->preserve_context) { ... } into #ifdef CONFIG_KEXEC_JUMP to make code looks cleaner. Fix no longer correct comments of kernel_kexec(). Signed-off-by: Huang Ying Acked-by: Vivek Goyal Cc: Pavel Machek Cc: "Rafael J. Wysocki" Cc: "Eric W. Biederman" Cc: Vivek Goyal Cc: Ingo Molnar Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- kernel/kexec.c | 17 ++++++++--------- 1 file changed, 8 insertions(+), 9 deletions(-) diff --git a/kernel/kexec.c b/kernel/kexec.c index cf3797b7678..bfbbd120623 100644 --- a/kernel/kexec.c +++ b/kernel/kexec.c @@ -1426,11 +1426,9 @@ static int __init crash_save_vmcoreinfo_init(void) module_init(crash_save_vmcoreinfo_init) -/** - * kernel_kexec - reboot the system - * - * Move into place and start executing a preloaded standalone - * executable. If nothing was preloaded return an error. +/* + * Move into place and start executing a preloaded standalone + * executable. If nothing was preloaded return an error. */ int kernel_kexec(void) { @@ -1443,8 +1441,8 @@ int kernel_kexec(void) goto Unlock; } - if (kexec_image->preserve_context) { #ifdef CONFIG_KEXEC_JUMP + if (kexec_image->preserve_context) { mutex_lock(&pm_mutex); pm_prepare_console(); error = freeze_processes(); @@ -1471,8 +1469,9 @@ int kernel_kexec(void) if (error) goto Enable_irqs; save_processor_state(); + } else #endif - } else { + { blocking_notifier_call_chain(&reboot_notifier_list, SYS_RESTART, NULL); system_state = SYSTEM_RESTART; @@ -1484,8 +1483,8 @@ int kernel_kexec(void) machine_kexec(kexec_image); - if (kexec_image->preserve_context) { #ifdef CONFIG_KEXEC_JUMP + if (kexec_image->preserve_context) { restore_processor_state(); device_power_up(PMSG_RESTORE); Enable_irqs: @@ -1499,8 +1498,8 @@ int kernel_kexec(void) Restore_console: pm_restore_console(); mutex_unlock(&pm_mutex); -#endif } +#endif Unlock: if (!xchg(&kexec_lock, 0)) -- GitLab From 163f6876f5c3ff8215e900b93779e960a56b3694 Mon Sep 17 00:00:00 2001 From: Huang Ying Date: Fri, 15 Aug 2008 00:40:22 -0700 Subject: [PATCH 414/750] kexec jump: rename KEXEC_CONTROL_CODE_SIZE to KEXEC_CONTROL_PAGE_SIZE Rename KEXEC_CONTROL_CODE_SIZE to KEXEC_CONTROL_PAGE_SIZE, because control page is used for not only code on some platform. For example in kexec jump, it is used for data and stack too. [akpm@linux-foundation.org: unbreak powerpc and arm, finish conversion] Signed-off-by: Huang Ying Cc: Pavel Machek Cc: "Rafael J. Wysocki" Cc: "Eric W. Biederman" Cc: Vivek Goyal Cc: Ingo Molnar Cc: Russell King Cc: Benjamin Herrenschmidt Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- arch/arm/include/asm/kexec.h | 2 +- arch/arm/kernel/machine_kexec.c | 2 +- arch/ia64/include/asm/kexec.h | 2 +- arch/powerpc/include/asm/kexec.h | 2 +- arch/powerpc/kernel/machine_kexec_32.c | 2 +- arch/s390/include/asm/kexec.h | 2 +- arch/sh/include/asm/kexec.h | 2 +- arch/x86/kernel/machine_kexec_32.c | 2 +- include/asm-mips/kexec.h | 2 +- include/asm-x86/kexec.h | 4 ++-- include/linux/kexec.h | 4 ++-- kernel/kexec.c | 6 +++--- 12 files changed, 16 insertions(+), 16 deletions(-) diff --git a/arch/arm/include/asm/kexec.h b/arch/arm/include/asm/kexec.h index c8986bb99ed..df15a0dc228 100644 --- a/arch/arm/include/asm/kexec.h +++ b/arch/arm/include/asm/kexec.h @@ -10,7 +10,7 @@ /* Maximum address we can use for the control code buffer */ #define KEXEC_CONTROL_MEMORY_LIMIT (-1UL) -#define KEXEC_CONTROL_CODE_SIZE 4096 +#define KEXEC_CONTROL_PAGE_SIZE 4096 #define KEXEC_ARCH KEXEC_ARCH_ARM diff --git a/arch/arm/kernel/machine_kexec.c b/arch/arm/kernel/machine_kexec.c index db8f54a3451..fae5beb3c3d 100644 --- a/arch/arm/kernel/machine_kexec.c +++ b/arch/arm/kernel/machine_kexec.c @@ -71,7 +71,7 @@ void machine_kexec(struct kimage *image) flush_icache_range((unsigned long) reboot_code_buffer, - (unsigned long) reboot_code_buffer + KEXEC_CONTROL_CODE_SIZE); + (unsigned long) reboot_code_buffer + KEXEC_CONTROL_PAGE_SIZE); printk(KERN_INFO "Bye!\n"); cpu_proc_fin(); diff --git a/arch/ia64/include/asm/kexec.h b/arch/ia64/include/asm/kexec.h index 541be835fc5..e1d58f819d7 100644 --- a/arch/ia64/include/asm/kexec.h +++ b/arch/ia64/include/asm/kexec.h @@ -9,7 +9,7 @@ /* Maximum address we can use for the control code buffer */ #define KEXEC_CONTROL_MEMORY_LIMIT TASK_SIZE -#define KEXEC_CONTROL_CODE_SIZE (8192 + 8192 + 4096) +#define KEXEC_CONTROL_PAGE_SIZE (8192 + 8192 + 4096) /* The native architecture */ #define KEXEC_ARCH KEXEC_ARCH_IA_64 diff --git a/arch/powerpc/include/asm/kexec.h b/arch/powerpc/include/asm/kexec.h index acdcdc66f1b..3736d9b3328 100644 --- a/arch/powerpc/include/asm/kexec.h +++ b/arch/powerpc/include/asm/kexec.h @@ -22,7 +22,7 @@ #define KEXEC_CONTROL_MEMORY_LIMIT TASK_SIZE #endif -#define KEXEC_CONTROL_CODE_SIZE 4096 +#define KEXEC_CONTROL_PAGE_SIZE 4096 /* The native architecture */ #ifdef __powerpc64__ diff --git a/arch/powerpc/kernel/machine_kexec_32.c b/arch/powerpc/kernel/machine_kexec_32.c index cbaa3419679..ae63a964b85 100644 --- a/arch/powerpc/kernel/machine_kexec_32.c +++ b/arch/powerpc/kernel/machine_kexec_32.c @@ -51,7 +51,7 @@ void default_machine_kexec(struct kimage *image) relocate_new_kernel_size); flush_icache_range(reboot_code_buffer, - reboot_code_buffer + KEXEC_CONTROL_CODE_SIZE); + reboot_code_buffer + KEXEC_CONTROL_PAGE_SIZE); printk(KERN_INFO "Bye!\n"); /* now call it */ diff --git a/arch/s390/include/asm/kexec.h b/arch/s390/include/asm/kexec.h index f219c6411e0..bb729b84a21 100644 --- a/arch/s390/include/asm/kexec.h +++ b/arch/s390/include/asm/kexec.h @@ -31,7 +31,7 @@ #define KEXEC_CONTROL_MEMORY_LIMIT (1UL<<31) /* Allocate one page for the pdp and the second for the code */ -#define KEXEC_CONTROL_CODE_SIZE 4096 +#define KEXEC_CONTROL_PAGE_SIZE 4096 /* The native architecture */ #define KEXEC_ARCH KEXEC_ARCH_S390 diff --git a/arch/sh/include/asm/kexec.h b/arch/sh/include/asm/kexec.h index 00f4260ef09..765a5e1660f 100644 --- a/arch/sh/include/asm/kexec.h +++ b/arch/sh/include/asm/kexec.h @@ -21,7 +21,7 @@ /* Maximum address we can use for the control code buffer */ #define KEXEC_CONTROL_MEMORY_LIMIT TASK_SIZE -#define KEXEC_CONTROL_CODE_SIZE 4096 +#define KEXEC_CONTROL_PAGE_SIZE 4096 /* The native architecture */ #define KEXEC_ARCH KEXEC_ARCH_SH diff --git a/arch/x86/kernel/machine_kexec_32.c b/arch/x86/kernel/machine_kexec_32.c index 9fe478d9840..466450167de 100644 --- a/arch/x86/kernel/machine_kexec_32.c +++ b/arch/x86/kernel/machine_kexec_32.c @@ -78,7 +78,7 @@ static void load_segments(void) /* * A architecture hook called to validate the * proposed image and prepare the control pages - * as needed. The pages for KEXEC_CONTROL_CODE_SIZE + * as needed. The pages for KEXEC_CONTROL_PAGE_SIZE * have been allocated, but the segments have yet * been copied into the kernel. * diff --git a/include/asm-mips/kexec.h b/include/asm-mips/kexec.h index cdbab43b7d3..4314892aaeb 100644 --- a/include/asm-mips/kexec.h +++ b/include/asm-mips/kexec.h @@ -16,7 +16,7 @@ /* Maximum address we can use for the control code buffer */ #define KEXEC_CONTROL_MEMORY_LIMIT (0x20000000) -#define KEXEC_CONTROL_CODE_SIZE 4096 +#define KEXEC_CONTROL_PAGE_SIZE 4096 /* The native architecture */ #define KEXEC_ARCH KEXEC_ARCH_MIPS diff --git a/include/asm-x86/kexec.h b/include/asm-x86/kexec.h index c0e52a14fd4..f6fb3d21883 100644 --- a/include/asm-x86/kexec.h +++ b/include/asm-x86/kexec.h @@ -63,7 +63,7 @@ /* Maximum address we can use for the control code buffer */ # define KEXEC_CONTROL_MEMORY_LIMIT TASK_SIZE -# define KEXEC_CONTROL_CODE_SIZE 4096 +# define KEXEC_CONTROL_PAGE_SIZE 4096 /* The native architecture */ # define KEXEC_ARCH KEXEC_ARCH_386 @@ -79,7 +79,7 @@ # define KEXEC_CONTROL_MEMORY_LIMIT (0xFFFFFFFFFFUL) /* Allocate one page for the pdp and the second for the code */ -# define KEXEC_CONTROL_CODE_SIZE (4096UL + 4096UL) +# define KEXEC_CONTROL_PAGE_SIZE (4096UL + 4096UL) /* The native architecture */ # define KEXEC_ARCH KEXEC_ARCH_X86_64 diff --git a/include/linux/kexec.h b/include/linux/kexec.h index 32110cede64..17f76fc0517 100644 --- a/include/linux/kexec.h +++ b/include/linux/kexec.h @@ -25,8 +25,8 @@ #error KEXEC_CONTROL_MEMORY_LIMIT not defined #endif -#ifndef KEXEC_CONTROL_CODE_SIZE -#error KEXEC_CONTROL_CODE_SIZE not defined +#ifndef KEXEC_CONTROL_PAGE_SIZE +#error KEXEC_CONTROL_PAGE_SIZE not defined #endif #ifndef KEXEC_ARCH diff --git a/kernel/kexec.c b/kernel/kexec.c index bfbbd120623..2810558802b 100644 --- a/kernel/kexec.c +++ b/kernel/kexec.c @@ -77,7 +77,7 @@ int kexec_should_crash(struct task_struct *p) * * The code for the transition from the current kernel to the * the new kernel is placed in the control_code_buffer, whose size - * is given by KEXEC_CONTROL_CODE_SIZE. In the best case only a single + * is given by KEXEC_CONTROL_PAGE_SIZE. In the best case only a single * page of memory is necessary, but some architectures require more. * Because this memory must be identity mapped in the transition from * virtual to physical addresses it must live in the range @@ -242,7 +242,7 @@ static int kimage_normal_alloc(struct kimage **rimage, unsigned long entry, */ result = -ENOMEM; image->control_code_page = kimage_alloc_control_pages(image, - get_order(KEXEC_CONTROL_CODE_SIZE)); + get_order(KEXEC_CONTROL_PAGE_SIZE)); if (!image->control_code_page) { printk(KERN_ERR "Could not allocate control_code_buffer\n"); goto out; @@ -317,7 +317,7 @@ static int kimage_crash_alloc(struct kimage **rimage, unsigned long entry, */ result = -ENOMEM; image->control_code_page = kimage_alloc_control_pages(image, - get_order(KEXEC_CONTROL_CODE_SIZE)); + get_order(KEXEC_CONTROL_PAGE_SIZE)); if (!image->control_code_page) { printk(KERN_ERR "Could not allocate control_code_buffer\n"); goto out; -- GitLab From fb45daa69d287b394eca1619b3fadff7c0215c71 Mon Sep 17 00:00:00 2001 From: Huang Ying Date: Fri, 15 Aug 2008 00:40:23 -0700 Subject: [PATCH 415/750] kexec jump: check code size in control page Kexec/Kexec-jump require code size in control page is less than PAGE_SIZE/2. This patch add link-time checking for this. ASSERT() of ld link script is used as the link-time checking mechanism. [akpm@linux-foundation.org: build fix] Signed-off-by: Huang Ying Cc: Pavel Machek Cc: "Rafael J. Wysocki" Cc: "Eric W. Biederman" Acked-by: Vivek Goyal Cc: Ingo Molnar Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- arch/x86/kernel/machine_kexec_32.c | 2 +- arch/x86/kernel/relocate_kernel_32.S | 10 +++++++--- arch/x86/kernel/vmlinux_32.lds.S | 8 ++++++++ include/asm-x86/kexec.h | 4 ++++ 4 files changed, 20 insertions(+), 4 deletions(-) diff --git a/arch/x86/kernel/machine_kexec_32.c b/arch/x86/kernel/machine_kexec_32.c index 466450167de..5c8e7735c89 100644 --- a/arch/x86/kernel/machine_kexec_32.c +++ b/arch/x86/kernel/machine_kexec_32.c @@ -138,7 +138,7 @@ void machine_kexec(struct kimage *image) } control_page = page_address(image->control_code_page); - memcpy(control_page, relocate_kernel, PAGE_SIZE/2); + memcpy(control_page, relocate_kernel, KEXEC_CONTROL_CODE_MAX_SIZE); relocate_kernel_ptr = control_page; page_list[PA_CONTROL_PAGE] = __pa(control_page); diff --git a/arch/x86/kernel/relocate_kernel_32.S b/arch/x86/kernel/relocate_kernel_32.S index 703310a9902..6f50664b2ba 100644 --- a/arch/x86/kernel/relocate_kernel_32.S +++ b/arch/x86/kernel/relocate_kernel_32.S @@ -20,10 +20,11 @@ #define PAGE_ATTR (_PAGE_PRESENT | _PAGE_RW | _PAGE_ACCESSED | _PAGE_DIRTY) #define PAE_PGD_ATTR (_PAGE_PRESENT) -/* control_page + PAGE_SIZE/2 ~ control_page + PAGE_SIZE * 3/4 are - * used to save some data for jumping back +/* control_page + KEXEC_CONTROL_CODE_MAX_SIZE + * ~ control_page + PAGE_SIZE are used as data storage and stack for + * jumping back */ -#define DATA(offset) (PAGE_SIZE/2+(offset)) +#define DATA(offset) (KEXEC_CONTROL_CODE_MAX_SIZE+(offset)) /* Minimal CPU state */ #define ESP DATA(0x0) @@ -376,3 +377,6 @@ swap_pages: popl %ebx popl %ebp ret + + .globl kexec_control_code_size +.set kexec_control_code_size, . - relocate_kernel diff --git a/arch/x86/kernel/vmlinux_32.lds.S b/arch/x86/kernel/vmlinux_32.lds.S index cdb2363697d..af5bdad8460 100644 --- a/arch/x86/kernel/vmlinux_32.lds.S +++ b/arch/x86/kernel/vmlinux_32.lds.S @@ -209,3 +209,11 @@ SECTIONS DWARF_DEBUG } + +#ifdef CONFIG_KEXEC +/* Link time checks */ +#include + +ASSERT(kexec_control_code_size <= KEXEC_CONTROL_CODE_MAX_SIZE, + "kexec control code size is too big") +#endif diff --git a/include/asm-x86/kexec.h b/include/asm-x86/kexec.h index f6fb3d21883..4246ab7dc98 100644 --- a/include/asm-x86/kexec.h +++ b/include/asm-x86/kexec.h @@ -41,6 +41,10 @@ # define PAGES_NR 17 #endif +#ifdef CONFIG_X86_32 +# define KEXEC_CONTROL_CODE_MAX_SIZE 2048 +#endif + #ifndef __ASSEMBLY__ #include -- GitLab From ca195b7f6da3d5dde0bb85a7c322d7de73352653 Mon Sep 17 00:00:00 2001 From: Huang Ying Date: Fri, 15 Aug 2008 00:40:24 -0700 Subject: [PATCH 416/750] kexec jump: remove duplication of kexec_restart_prepare() Call kernel_restart_prepare() in kernel_kexec() instead of duplicating the code. Signed-off-by: Huang Ying Acked-by: Pavel Machek Acked-by: Vivek Goyal Cc: Pavel Machek Cc: "Rafael J. Wysocki" Cc: "Eric W. Biederman" Cc: Vivek Goyal Cc: Ingo Molnar Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- include/linux/reboot.h | 1 + kernel/kexec.c | 6 +----- kernel/sys.c | 2 +- 3 files changed, 3 insertions(+), 6 deletions(-) diff --git a/include/linux/reboot.h b/include/linux/reboot.h index b93b541cf11..988e55fe649 100644 --- a/include/linux/reboot.h +++ b/include/linux/reboot.h @@ -59,6 +59,7 @@ extern void machine_crash_shutdown(struct pt_regs *); * Architecture independent implemenations of sys_reboot commands. */ +extern void kernel_restart_prepare(char *cmd); extern void kernel_restart(char *cmd); extern void kernel_halt(void); extern void kernel_power_off(void); diff --git a/kernel/kexec.c b/kernel/kexec.c index 2810558802b..b81682312dc 100644 --- a/kernel/kexec.c +++ b/kernel/kexec.c @@ -1472,11 +1472,7 @@ int kernel_kexec(void) } else #endif { - blocking_notifier_call_chain(&reboot_notifier_list, - SYS_RESTART, NULL); - system_state = SYSTEM_RESTART; - device_shutdown(); - sysdev_shutdown(); + kernel_restart_prepare(NULL); printk(KERN_EMERG "Starting new kernel\n"); machine_shutdown(); } diff --git a/kernel/sys.c b/kernel/sys.c index c01858090a9..3dacb00a7f7 100644 --- a/kernel/sys.c +++ b/kernel/sys.c @@ -274,7 +274,7 @@ void emergency_restart(void) } EXPORT_SYMBOL_GPL(emergency_restart); -static void kernel_restart_prepare(char *cmd) +void kernel_restart_prepare(char *cmd) { blocking_notifier_call_chain(&reboot_notifier_list, SYS_RESTART, cmd); system_state = SYSTEM_RESTART; -- GitLab From 73bd9c72a29be1e8de008186eea55d333a938804 Mon Sep 17 00:00:00 2001 From: Huang Ying Date: Fri, 15 Aug 2008 00:40:24 -0700 Subject: [PATCH 417/750] kexec jump: in sync with hibernation implementation Add device_pm_lock() and device_pm_unlock() in kernel_kexec() in sync with current hibernation implementation. Signed-off-by: Huang Ying Acked-by: Pavel Machek Cc: "Rafael J. Wysocki" Cc: "Eric W. Biederman" Cc: Vivek Goyal Cc: Ingo Molnar Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- kernel/kexec.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/kernel/kexec.c b/kernel/kexec.c index b81682312dc..17c80fdc453 100644 --- a/kernel/kexec.c +++ b/kernel/kexec.c @@ -1457,6 +1457,7 @@ int kernel_kexec(void) error = disable_nonboot_cpus(); if (error) goto Resume_devices; + device_pm_lock(); local_irq_disable(); /* At this point, device_suspend() has been called, * but *not* device_power_down(). We *must* @@ -1485,6 +1486,7 @@ int kernel_kexec(void) device_power_up(PMSG_RESTORE); Enable_irqs: local_irq_enable(); + device_pm_unlock(); enable_nonboot_cpus(); Resume_devices: device_resume(PMSG_RESTORE); -- GitLab From 9bdeb7b5d34f197dea7859d24475943395ffea5e Mon Sep 17 00:00:00 2001 From: Huang Ying Date: Fri, 15 Aug 2008 00:40:25 -0700 Subject: [PATCH 418/750] kexec jump: __ftrace_enabled_save/restore Add __ftrace_enabled_save/restore, used to disable ftrace for a while. Now, this is used by kexec jump, which need a version without lock, for general situation, a locked version should be used. Signed-off-by: Huang Ying Cc: Pavel Machek Cc: "Rafael J. Wysocki" Cc: "Eric W. Biederman" Cc: Vivek Goyal Cc: Ingo Molnar Cc: Steven Rostedt Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- include/linux/ftrace.h | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+) diff --git a/include/linux/ftrace.h b/include/linux/ftrace.h index f368d041e02..bb384068272 100644 --- a/include/linux/ftrace.h +++ b/include/linux/ftrace.h @@ -98,6 +98,27 @@ static inline void tracer_disable(void) #endif } +/* Ftrace disable/restore without lock. Some synchronization mechanism + * must be used to prevent ftrace_enabled to be changed between + * disable/restore. */ +static inline int __ftrace_enabled_save(void) +{ +#ifdef CONFIG_FTRACE + int saved_ftrace_enabled = ftrace_enabled; + ftrace_enabled = 0; + return saved_ftrace_enabled; +#else + return 0; +#endif +} + +static inline void __ftrace_enabled_restore(int enabled) +{ +#ifdef CONFIG_FTRACE + ftrace_enabled = enabled; +#endif +} + #ifdef CONFIG_FRAME_POINTER /* TODO: need to fix this for ARM */ # define CALLER_ADDR0 ((unsigned long)__builtin_return_address(0)) -- GitLab From 3122c331190e9d1622bf1c8cf6ce3b17cca67c9e Mon Sep 17 00:00:00 2001 From: Huang Ying Date: Fri, 15 Aug 2008 00:40:26 -0700 Subject: [PATCH 419/750] kexec jump: fix for ftrace Ftrace depends on some processor state that we destroyed during kexec and restored by restore_processor_state(). So save_processor_state() and restore_processor_state() are moved into machine_kexec() and ftrace is restored after restore_processor_state(). Signed-off-by: Huang Ying Cc: Pavel Machek Cc: "Rafael J. Wysocki" Cc: "Eric W. Biederman" Cc: Vivek Goyal Cc: Ingo Molnar Cc: Steven Rostedt Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- arch/x86/kernel/machine_kexec_32.c | 16 +++++++++++++++- kernel/kexec.c | 2 -- 2 files changed, 15 insertions(+), 3 deletions(-) diff --git a/arch/x86/kernel/machine_kexec_32.c b/arch/x86/kernel/machine_kexec_32.c index 5c8e7735c89..0732adba05c 100644 --- a/arch/x86/kernel/machine_kexec_32.c +++ b/arch/x86/kernel/machine_kexec_32.c @@ -12,6 +12,7 @@ #include #include #include +#include #include #include @@ -113,6 +114,7 @@ void machine_kexec(struct kimage *image) { unsigned long page_list[PAGES_NR]; void *control_page; + int save_ftrace_enabled; asmlinkage unsigned long (*relocate_kernel_ptr)(unsigned long indirection_page, unsigned long control_page, @@ -120,7 +122,12 @@ void machine_kexec(struct kimage *image) unsigned int has_pae, unsigned int preserve_context); - tracer_disable(); +#ifdef CONFIG_KEXEC_JUMP + if (kexec_image->preserve_context) + save_processor_state(); +#endif + + save_ftrace_enabled = __ftrace_enabled_save(); /* Interrupts aren't acceptable while we reboot */ local_irq_disable(); @@ -178,6 +185,13 @@ void machine_kexec(struct kimage *image) (unsigned long)page_list, image->start, cpu_has_pae, image->preserve_context); + +#ifdef CONFIG_KEXEC_JUMP + if (kexec_image->preserve_context) + restore_processor_state(); +#endif + + __ftrace_enabled_restore(save_ftrace_enabled); } void arch_crash_save_vmcoreinfo(void) diff --git a/kernel/kexec.c b/kernel/kexec.c index 17c80fdc453..9fc6f7cbd8a 100644 --- a/kernel/kexec.c +++ b/kernel/kexec.c @@ -1469,7 +1469,6 @@ int kernel_kexec(void) error = device_power_down(PMSG_FREEZE); if (error) goto Enable_irqs; - save_processor_state(); } else #endif { @@ -1482,7 +1481,6 @@ int kernel_kexec(void) #ifdef CONFIG_KEXEC_JUMP if (kexec_image->preserve_context) { - restore_processor_state(); device_power_up(PMSG_RESTORE); Enable_irqs: local_irq_enable(); -- GitLab From 8c5a1cf0ad3ac5fcdf51314a63b16a440870f6a2 Mon Sep 17 00:00:00 2001 From: Andrew Morton Date: Fri, 15 Aug 2008 00:40:27 -0700 Subject: [PATCH 420/750] kexec: use a mutex for locking rather than xchg() Functionally the same, but more conventional. Cc: Huang Ying Tested-by: Vivek Goyal Cc: "Eric W. Biederman" Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- kernel/kexec.c | 34 ++++++++++------------------------ 1 file changed, 10 insertions(+), 24 deletions(-) diff --git a/kernel/kexec.c b/kernel/kexec.c index 9fc6f7cbd8a..59f3f0df35d 100644 --- a/kernel/kexec.c +++ b/kernel/kexec.c @@ -12,7 +12,7 @@ #include #include #include -#include +#include #include #include #include @@ -924,19 +924,14 @@ static int kimage_load_segment(struct kimage *image, */ struct kimage *kexec_image; struct kimage *kexec_crash_image; -/* - * A home grown binary mutex. - * Nothing can wait so this mutex is safe to use - * in interrupt context :) - */ -static int kexec_lock; + +static DEFINE_MUTEX(kexec_mutex); asmlinkage long sys_kexec_load(unsigned long entry, unsigned long nr_segments, struct kexec_segment __user *segments, unsigned long flags) { struct kimage **dest_image, *image; - int locked; int result; /* We only trust the superuser with rebooting the system. */ @@ -972,8 +967,7 @@ asmlinkage long sys_kexec_load(unsigned long entry, unsigned long nr_segments, * * KISS: always take the mutex. */ - locked = xchg(&kexec_lock, 1); - if (locked) + if (!mutex_trylock(&kexec_mutex)) return -EBUSY; dest_image = &kexec_image; @@ -1015,8 +1009,7 @@ asmlinkage long sys_kexec_load(unsigned long entry, unsigned long nr_segments, image = xchg(dest_image, image); out: - locked = xchg(&kexec_lock, 0); /* Release the mutex */ - BUG_ON(!locked); + mutex_unlock(&kexec_mutex); kimage_free(image); return result; @@ -1063,10 +1056,7 @@ asmlinkage long compat_sys_kexec_load(unsigned long entry, void crash_kexec(struct pt_regs *regs) { - int locked; - - - /* Take the kexec_lock here to prevent sys_kexec_load + /* Take the kexec_mutex here to prevent sys_kexec_load * running on one cpu from replacing the crash kernel * we are using after a panic on a different cpu. * @@ -1074,8 +1064,7 @@ void crash_kexec(struct pt_regs *regs) * of memory the xchg(&kexec_crash_image) would be * sufficient. But since I reuse the memory... */ - locked = xchg(&kexec_lock, 1); - if (!locked) { + if (mutex_trylock(&kexec_mutex)) { if (kexec_crash_image) { struct pt_regs fixed_regs; crash_setup_regs(&fixed_regs, regs); @@ -1083,8 +1072,7 @@ void crash_kexec(struct pt_regs *regs) machine_crash_shutdown(&fixed_regs); machine_kexec(kexec_crash_image); } - locked = xchg(&kexec_lock, 0); - BUG_ON(!locked); + mutex_unlock(&kexec_mutex); } } @@ -1434,7 +1422,7 @@ int kernel_kexec(void) { int error = 0; - if (xchg(&kexec_lock, 1)) + if (!mutex_trylock(&kexec_mutex)) return -EBUSY; if (!kexec_image) { error = -EINVAL; @@ -1498,8 +1486,6 @@ int kernel_kexec(void) #endif Unlock: - if (!xchg(&kexec_lock, 0)) - BUG(); - + mutex_unlock(&kexec_mutex); return error; } -- GitLab From ae5591e3f4754478b397a4e09ebd7cf4774ef88e Mon Sep 17 00:00:00 2001 From: York Sun Date: Fri, 15 Aug 2008 00:40:28 -0700 Subject: [PATCH 421/750] freescale DIU: add virtual resolution and panning support Application can now have the virtual resoltuion and use FBIOPAN_DISPLAY ioctl to pan. Signed-off-by: York Sun Cc: Kumar Gala Cc: "Antonino A. Daplas" Cc: Krzysztof Helt Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/fsl-diu-fb.c | 28 +++++++++++++++++++++++----- 1 file changed, 23 insertions(+), 5 deletions(-) diff --git a/drivers/video/fsl-diu-fb.c b/drivers/video/fsl-diu-fb.c index bd320a2bfb7..d9d24938da9 100644 --- a/drivers/video/fsl-diu-fb.c +++ b/drivers/video/fsl-diu-fb.c @@ -777,6 +777,22 @@ static void unmap_video_memory(struct fb_info *info) info->fix.smem_len = 0; } +/* + * Using the fb_var_screeninfo in fb_info we set the aoi of this + * particular framebuffer. It is a light version of fsl_diu_set_par. + */ +static int fsl_diu_set_aoi(struct fb_info *info) +{ + struct fb_var_screeninfo *var = &info->var; + struct mfb_info *mfbi = info->par; + struct diu_ad *ad = mfbi->ad; + + /* AOI should not be greater than display size */ + ad->offset_xyi = cpu_to_le32((var->yoffset << 16) | var->xoffset); + ad->offset_xyd = cpu_to_le32((mfbi->y_aoi_d << 16) | mfbi->x_aoi_d); + return 0; +} + /* * Using the fb_var_screeninfo in fb_info we set the resolution of this * particular framebuffer. This function alters the fb_fix_screeninfo stored @@ -817,11 +833,11 @@ static int fsl_diu_set_par(struct fb_info *info) diu_ops.get_pixel_format(var->bits_per_pixel, machine_data->monitor_port); ad->addr = cpu_to_le32(info->fix.smem_start); - ad->src_size_g_alpha = cpu_to_le32((var->yres << 12) | - var->xres) | mfbi->g_alpha; - /* fix me. AOI should not be greater than display size */ + ad->src_size_g_alpha = cpu_to_le32((var->yres_virtual << 12) | + var->xres_virtual) | mfbi->g_alpha; + /* AOI should not be greater than display size */ ad->aoi_size = cpu_to_le32((var->yres << 16) | var->xres); - ad->offset_xyi = 0; + ad->offset_xyi = cpu_to_le32((var->yoffset << 16) | var->xoffset); ad->offset_xyd = cpu_to_le32((mfbi->y_aoi_d << 16) | mfbi->x_aoi_d); /* Disable chroma keying function */ @@ -921,6 +937,8 @@ static int fsl_diu_pan_display(struct fb_var_screeninfo *var, else info->var.vmode &= ~FB_VMODE_YWRAP; + fsl_diu_set_aoi(info); + return 0; } @@ -989,7 +1007,7 @@ static int fsl_diu_ioctl(struct fb_info *info, unsigned int cmd, pr_debug("set AOI display offset of index %d to (%d,%d)\n", mfbi->index, aoi_d.x_aoi_d, aoi_d.y_aoi_d); fsl_diu_check_var(&info->var, info); - fsl_diu_set_par(info); + fsl_diu_set_aoi(info); break; case MFB_GET_AOID: aoi_d.x_aoi_d = mfbi->x_aoi_d; -- GitLab From fdfaa4833f984c6f8d44afb1fed6c0c775e6e67b Mon Sep 17 00:00:00 2001 From: York Sun Date: Fri, 15 Aug 2008 00:40:29 -0700 Subject: [PATCH 422/750] freescale DIU: bug fix: add sanity check for AOI position AOI position cannot be negative. Signed-off-by: York Sun Cc: Kumar Gala Cc: "Antonino A. Daplas" Cc: Krzysztof Helt Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/fsl-diu-fb.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/video/fsl-diu-fb.c b/drivers/video/fsl-diu-fb.c index d9d24938da9..fb51197d1c9 100644 --- a/drivers/video/fsl-diu-fb.c +++ b/drivers/video/fsl-diu-fb.c @@ -479,6 +479,10 @@ static void adjust_aoi_size_position(struct fb_var_screeninfo *var, base_plane_width = machine_data->fsl_diu_info[0]->var.xres; base_plane_height = machine_data->fsl_diu_info[0]->var.yres; + if (mfbi->x_aoi_d < 0) + mfbi->x_aoi_d = 0; + if (mfbi->y_aoi_d < 0) + mfbi->y_aoi_d = 0; switch (index) { case 0: if (mfbi->x_aoi_d != 0) -- GitLab From 9f86f28df14e06b12908d6475ee2462f0555bf34 Mon Sep 17 00:00:00 2001 From: Roberto De Ioris Date: Fri, 15 Aug 2008 00:40:30 -0700 Subject: [PATCH 423/750] applesmc: support for Intel iMac This adds support for fans and temperature sensors on intel iMac. Tested on iMac 24" 2.8ghz (iMac8,1), it supports the following sensors: cpu A ambient gpu gpu diode gpu heatsink hd bay 1 memory controller optical drive power Signed-off-by: Roberto De Ioris Cc: Nicolas Boichat Cc: Jean Delvare Cc: Mark M. Hoffman Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/hwmon/applesmc.c | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/drivers/hwmon/applesmc.c b/drivers/hwmon/applesmc.c index aacc0c4b809..52d842b48fa 100644 --- a/drivers/hwmon/applesmc.c +++ b/drivers/hwmon/applesmc.c @@ -98,6 +98,9 @@ static const char* temperature_sensors_sets[][36] = { "TH1P", "TH2P", "TH3P", "TMAP", "TMAS", "TMBS", "TM0P", "TM0S", "TM1P", "TM1S", "TM2P", "TM2S", "TM3S", "TM8P", "TM8S", "TM9P", "TM9S", "TN0H", "TS0C", NULL }, +/* Set 5: iMac */ + { "TC0D", "TA0P", "TG0P", "TG0D", "TG0H", "TH0P", "Tm0P", "TO0P", + "Tp0C", NULL }, }; /* List of keys used to read/write fan speeds */ @@ -1223,6 +1226,8 @@ static __initdata struct dmi_match_data applesmc_dmi_data[] = { { .accelerometer = 0, .light = 0, .temperature_set = 3 }, /* MacPro: temperature set 4 */ { .accelerometer = 0, .light = 0, .temperature_set = 4 }, +/* iMac: temperature set 5 */ + { .accelerometer = 0, .light = 0, .temperature_set = 5 }, }; /* Note that DMI_MATCH(...,"MacBook") will match "MacBookPro1,1". @@ -1248,6 +1253,10 @@ static __initdata struct dmi_system_id applesmc_whitelist[] = { DMI_MATCH(DMI_BOARD_VENDOR,"Apple"), DMI_MATCH(DMI_PRODUCT_NAME,"MacPro2") }, (void*)&applesmc_dmi_data[4]}, + { applesmc_dmi_match, "Apple iMac", { + DMI_MATCH(DMI_BOARD_VENDOR,"Apple"), + DMI_MATCH(DMI_PRODUCT_NAME,"iMac") }, + (void*)&applesmc_dmi_data[5]}, { .ident = NULL } }; -- GitLab From f91a79fe86a0becdf2506c189cdde154e82c787c Mon Sep 17 00:00:00 2001 From: "Guilherme M. Schroeder" Date: Fri, 15 Aug 2008 00:40:32 -0700 Subject: [PATCH 424/750] applesmc: add support for Macbook Add support for Macbook v3 (sensors and accelerometer). Signed-off-by: Nicolas Boichat Cc: "Mark M. Hoffman" Cc: Jean Delvare Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/hwmon/applesmc.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-) diff --git a/drivers/hwmon/applesmc.c b/drivers/hwmon/applesmc.c index 52d842b48fa..b06b8e090a2 100644 --- a/drivers/hwmon/applesmc.c +++ b/drivers/hwmon/applesmc.c @@ -101,6 +101,9 @@ static const char* temperature_sensors_sets[][36] = { /* Set 5: iMac */ { "TC0D", "TA0P", "TG0P", "TG0D", "TG0H", "TH0P", "Tm0P", "TO0P", "Tp0C", NULL }, +/* Set 6: Macbook3 set */ + { "TB0T", "TC0D", "TC0P", "TM0P", "TN0P", "TTF0", "TW0P", "Th0H", + "Th0S", "Th1H", NULL }, }; /* List of keys used to read/write fan speeds */ @@ -1228,6 +1231,8 @@ static __initdata struct dmi_match_data applesmc_dmi_data[] = { { .accelerometer = 0, .light = 0, .temperature_set = 4 }, /* iMac: temperature set 5 */ { .accelerometer = 0, .light = 0, .temperature_set = 5 }, +/* MacBook3: accelerometer and temperature set 6 */ + { .accelerometer = 1, .light = 0, .temperature_set = 6 }, }; /* Note that DMI_MATCH(...,"MacBook") will match "MacBookPro1,1". @@ -1237,10 +1242,14 @@ static __initdata struct dmi_system_id applesmc_whitelist[] = { DMI_MATCH(DMI_BOARD_VENDOR,"Apple"), DMI_MATCH(DMI_PRODUCT_NAME,"MacBookPro") }, (void*)&applesmc_dmi_data[0]}, - { applesmc_dmi_match, "Apple MacBook", { + { applesmc_dmi_match, "Apple MacBook (v2)", { DMI_MATCH(DMI_BOARD_VENDOR,"Apple"), DMI_MATCH(DMI_PRODUCT_NAME,"MacBook2") }, (void*)&applesmc_dmi_data[1]}, + { applesmc_dmi_match, "Apple MacBook (v3)", { + DMI_MATCH(DMI_BOARD_VENDOR,"Apple"), + DMI_MATCH(DMI_PRODUCT_NAME,"MacBook3") }, + (void*)&applesmc_dmi_data[6]}, { applesmc_dmi_match, "Apple MacBook", { DMI_MATCH(DMI_BOARD_VENDOR,"Apple"), DMI_MATCH(DMI_PRODUCT_NAME,"MacBook") }, -- GitLab From 16a515fd0cd3711a7da464d36009f18cd8e23f07 Mon Sep 17 00:00:00 2001 From: Michael Borisov Date: Fri, 15 Aug 2008 00:40:32 -0700 Subject: [PATCH 425/750] drivers/hwmon/w83791d.c: fix unused var warning drivers/hwmon/w83791d.c: In function `w83791d_probe': drivers/hwmon/w83791d.c:1049: warning: unused variable `val1' Signed-off-by: Michael Borisov Cc: "Mark M. Hoffman" Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/hwmon/w83791d.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/hwmon/w83791d.c b/drivers/hwmon/w83791d.c index daa7d121483..de21142d106 100644 --- a/drivers/hwmon/w83791d.c +++ b/drivers/hwmon/w83791d.c @@ -1055,9 +1055,10 @@ static int w83791d_probe(struct i2c_client *client, { struct w83791d_data *data; struct device *dev = &client->dev; - int i, val1, err; + int i, err; #ifdef DEBUG + int val1; val1 = w83791d_read(client, W83791D_REG_DID_VID4); dev_dbg(dev, "Device ID version: %d.%d (0x%02x)\n", (val1 >> 5) & 0x07, (val1 >> 1) & 0x0f, val1); -- GitLab From d42139a3fbd9793cf3747287e8f5c1ae06e06942 Mon Sep 17 00:00:00 2001 From: Marc Pignat Date: Fri, 15 Aug 2008 00:40:34 -0700 Subject: [PATCH 426/750] hwmon: ADC124S501 generic driver SPI driver for analog to digital converters national semiconductor ADC081S101, ADC124S501, ... Code for 8 channels by Tobias Himmer. This driver adds support for National Semiconductor ADCS chip family, where: * bb is the resolution in number of bits (8, 10, 12) * c is the number of channels (1, 2, 4, 8) * sss is the maximum conversion speed (021 for 200 kSPS, 051 for 500 kSPS and 101 for 1 MSPS) [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Marc Pignat Cc: Tobias Himmer Cc: "Mark M. Hoffman" Cc: Jean Delvare Cc: David Brownell Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/hwmon/Kconfig | 16 ++ drivers/hwmon/Makefile | 1 + drivers/hwmon/adcxx.c | 329 +++++++++++++++++++++++++++++++++++++++++ 3 files changed, 346 insertions(+) create mode 100644 drivers/hwmon/adcxx.c diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index bf4ebfb86fa..d402e8d813c 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -77,6 +77,22 @@ config SENSORS_AD7418 This driver can also be built as a module. If so, the module will be called ad7418. +config SENSORS_ADCXX + tristate "National Semiconductor ADCxxxSxxx" + depends on SPI_MASTER && EXPERIMENTAL + help + If you say yes here you get support for the National Semiconductor + ADCS chip family, where + * bb is the resolution in number of bits (8, 10, 12) + * c is the number of channels (1, 2, 4, 8) + * sss is the maximum conversion speed (021 for 200 kSPS, 051 for 500 + kSPS and 101 for 1 MSPS) + + Examples : ADC081S101, ADC124S501, ... + + This driver can also be built as a module. If so, the module + will be called adcxx. + config SENSORS_ADM1021 tristate "Analog Devices ADM1021 and compatibles" depends on I2C diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index 7943e5cefb0..950134ab842 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -17,6 +17,7 @@ obj-$(CONFIG_SENSORS_ABITUGURU) += abituguru.o obj-$(CONFIG_SENSORS_ABITUGURU3)+= abituguru3.o obj-$(CONFIG_SENSORS_AD7414) += ad7414.o obj-$(CONFIG_SENSORS_AD7418) += ad7418.o +obj-$(CONFIG_SENSORS_ADCXX) += adcxx.o obj-$(CONFIG_SENSORS_ADM1021) += adm1021.o obj-$(CONFIG_SENSORS_ADM1025) += adm1025.o obj-$(CONFIG_SENSORS_ADM1026) += adm1026.o diff --git a/drivers/hwmon/adcxx.c b/drivers/hwmon/adcxx.c new file mode 100644 index 00000000000..242294db3db --- /dev/null +++ b/drivers/hwmon/adcxx.c @@ -0,0 +1,329 @@ +/* + * adcxx.c + * + * The adcxx4s is an AD converter family from National Semiconductor (NS). + * + * Copyright (c) 2008 Marc Pignat + * + * The adcxx4s communicates with a host processor via an SPI/Microwire Bus + * interface. This driver supports the whole family of devices with name + * ADCS, where + * * bb is the resolution in number of bits (8, 10, 12) + * * c is the number of channels (1, 2, 4, 8) + * * sss is the maximum conversion speed (021 for 200 kSPS, 051 for 500 kSPS + * and 101 for 1 MSPS) + * + * Complete datasheets are available at National's website here: + * http://www.national.com/ds/DC/ADCS.pdf + * + * Handling of 8, 10 and 12 bits converters are the same, the + * unavailable bits are 0 :) + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define DRVNAME "adcxx" + +struct adcxx { + struct device *hwmon_dev; + struct mutex lock; + u32 channels; + u32 reference; /* in millivolts */ +}; + +/* sysfs hook function */ +static ssize_t adcxx_read(struct device *dev, + struct device_attribute *devattr, char *buf) +{ + struct spi_device *spi = to_spi_device(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct adcxx *adc = dev_get_drvdata(&spi->dev); + u8 tx_buf[2] = { attr->index << 3 }; /* other bits are don't care */ + u8 rx_buf[2]; + int status; + int value; + + if (mutex_lock_interruptible(&adc->lock)) + return -ERESTARTSYS; + + status = spi_write_then_read(spi, tx_buf, sizeof(tx_buf), + rx_buf, sizeof(rx_buf)); + if (status < 0) { + dev_warn(dev, "spi_write_then_read failed with status %d\n", + status); + goto out; + } + + value = (rx_buf[0] << 8) + rx_buf[1]; + dev_dbg(dev, "raw value = 0x%x\n", value); + + value = value * adc->reference >> 12; + status = sprintf(buf, "%d\n", value); +out: + mutex_unlock(&adc->lock); + return status; +} + +static ssize_t adcxx_show_min(struct device *dev, + struct device_attribute *devattr, char *buf) +{ + /* The minimum reference is 0 for this chip family */ + return sprintf(buf, "0\n"); +} + +static ssize_t adcxx_show_max(struct device *dev, + struct device_attribute *devattr, char *buf) +{ + struct spi_device *spi = to_spi_device(dev); + struct adcxx *adc = dev_get_drvdata(&spi->dev); + u32 reference; + + if (mutex_lock_interruptible(&adc->lock)) + return -ERESTARTSYS; + + reference = adc->reference; + + mutex_unlock(&adc->lock); + + return sprintf(buf, "%d\n", reference); +} + +static ssize_t adcxx_set_max(struct device *dev, + struct device_attribute *devattr, const char *buf, size_t count) +{ + struct spi_device *spi = to_spi_device(dev); + struct adcxx *adc = dev_get_drvdata(&spi->dev); + unsigned long value; + + if (strict_strtoul(buf, 10, &value)) + return -EINVAL; + + if (mutex_lock_interruptible(&adc->lock)) + return -ERESTARTSYS; + + adc->reference = value; + + mutex_unlock(&adc->lock); + + return count; +} + +static ssize_t adcxx_show_name(struct device *dev, struct device_attribute + *devattr, char *buf) +{ + struct spi_device *spi = to_spi_device(dev); + struct adcxx *adc = dev_get_drvdata(&spi->dev); + + return sprintf(buf, "adcxx%ds\n", adc->channels); +} + +static struct sensor_device_attribute ad_input[] = { + SENSOR_ATTR(name, S_IRUGO, adcxx_show_name, NULL, 0), + SENSOR_ATTR(in_min, S_IRUGO, adcxx_show_min, NULL, 0), + SENSOR_ATTR(in_max, S_IWUSR | S_IRUGO, adcxx_show_max, + adcxx_set_max, 0), + SENSOR_ATTR(in0_input, S_IRUGO, adcxx_read, NULL, 0), + SENSOR_ATTR(in1_input, S_IRUGO, adcxx_read, NULL, 1), + SENSOR_ATTR(in2_input, S_IRUGO, adcxx_read, NULL, 2), + SENSOR_ATTR(in3_input, S_IRUGO, adcxx_read, NULL, 3), + SENSOR_ATTR(in4_input, S_IRUGO, adcxx_read, NULL, 4), + SENSOR_ATTR(in5_input, S_IRUGO, adcxx_read, NULL, 5), + SENSOR_ATTR(in6_input, S_IRUGO, adcxx_read, NULL, 6), + SENSOR_ATTR(in7_input, S_IRUGO, adcxx_read, NULL, 7), +}; + +/*----------------------------------------------------------------------*/ + +static int __devinit adcxx_probe(struct spi_device *spi, int channels) +{ + struct adcxx *adc; + int status; + int i; + + adc = kzalloc(sizeof *adc, GFP_KERNEL); + if (!adc) + return -ENOMEM; + + /* set a default value for the reference */ + adc->reference = 3300; + adc->channels = channels; + mutex_init(&adc->lock); + + mutex_lock(&adc->lock); + + dev_set_drvdata(&spi->dev, adc); + + for (i = 0; i < 3 + adc->channels; i++) { + status = device_create_file(&spi->dev, &ad_input[i].dev_attr); + if (status) { + dev_err(&spi->dev, "device_create_file failed.\n"); + goto out_err; + } + } + + adc->hwmon_dev = hwmon_device_register(&spi->dev); + if (IS_ERR(adc->hwmon_dev)) { + dev_err(&spi->dev, "hwmon_device_register failed.\n"); + status = PTR_ERR(adc->hwmon_dev); + goto out_err; + } + + mutex_unlock(&adc->lock); + return 0; + +out_err: + for (i--; i >= 0; i--) + device_remove_file(&spi->dev, &ad_input[i].dev_attr); + + dev_set_drvdata(&spi->dev, NULL); + mutex_unlock(&adc->lock); + kfree(adc); + return status; +} + +static int __devinit adcxx1s_probe(struct spi_device *spi) +{ + return adcxx_probe(spi, 1); +} + +static int __devinit adcxx2s_probe(struct spi_device *spi) +{ + return adcxx_probe(spi, 2); +} + +static int __devinit adcxx4s_probe(struct spi_device *spi) +{ + return adcxx_probe(spi, 4); +} + +static int __devinit adcxx8s_probe(struct spi_device *spi) +{ + return adcxx_probe(spi, 8); +} + +static int __devexit adcxx_remove(struct spi_device *spi) +{ + struct adcxx *adc = dev_get_drvdata(&spi->dev); + int i; + + mutex_lock(&adc->lock); + hwmon_device_unregister(adc->hwmon_dev); + for (i = 0; i < 3 + adc->channels; i++) + device_remove_file(&spi->dev, &ad_input[i].dev_attr); + + dev_set_drvdata(&spi->dev, NULL); + mutex_unlock(&adc->lock); + kfree(adc); + + return 0; +} + +static struct spi_driver adcxx1s_driver = { + .driver = { + .name = "adcxx1s", + .owner = THIS_MODULE, + }, + .probe = adcxx1s_probe, + .remove = __devexit_p(adcxx_remove), +}; + +static struct spi_driver adcxx2s_driver = { + .driver = { + .name = "adcxx2s", + .owner = THIS_MODULE, + }, + .probe = adcxx2s_probe, + .remove = __devexit_p(adcxx_remove), +}; + +static struct spi_driver adcxx4s_driver = { + .driver = { + .name = "adcxx4s", + .owner = THIS_MODULE, + }, + .probe = adcxx4s_probe, + .remove = __devexit_p(adcxx_remove), +}; + +static struct spi_driver adcxx8s_driver = { + .driver = { + .name = "adcxx8s", + .owner = THIS_MODULE, + }, + .probe = adcxx8s_probe, + .remove = __devexit_p(adcxx_remove), +}; + +static int __init init_adcxx(void) +{ + int status; + status = spi_register_driver(&adcxx1s_driver); + if (status) + goto reg_1_failed; + + status = spi_register_driver(&adcxx2s_driver); + if (status) + goto reg_2_failed; + + status = spi_register_driver(&adcxx4s_driver); + if (status) + goto reg_4_failed; + + status = spi_register_driver(&adcxx8s_driver); + if (status) + goto reg_8_failed; + + return status; + +reg_8_failed: + spi_unregister_driver(&adcxx4s_driver); +reg_4_failed: + spi_unregister_driver(&adcxx2s_driver); +reg_2_failed: + spi_unregister_driver(&adcxx1s_driver); +reg_1_failed: + return status; +} + +static void __exit exit_adcxx(void) +{ + spi_unregister_driver(&adcxx1s_driver); + spi_unregister_driver(&adcxx2s_driver); + spi_unregister_driver(&adcxx4s_driver); + spi_unregister_driver(&adcxx8s_driver); +} + +module_init(init_adcxx); +module_exit(exit_adcxx); + +MODULE_AUTHOR("Marc Pignat"); +MODULE_DESCRIPTION("National Semiconductor adcxx8sxxx Linux driver"); +MODULE_LICENSE("GPL"); + +MODULE_ALIAS("adcxx1s"); +MODULE_ALIAS("adcxx2s"); +MODULE_ALIAS("adcxx4s"); +MODULE_ALIAS("adcxx8s"); -- GitLab From 963d96b53e1f4ebf4db0b8b7ba71ff7b438fbee0 Mon Sep 17 00:00:00 2001 From: "Darrick J. Wong" Date: Fri, 15 Aug 2008 00:40:36 -0700 Subject: [PATCH 427/750] i5k_amb: provide labels for temperature sensors Export the sensor -> channel/dimm mapping in tempX_label. Signed-off-by: Darrick J. Wong Cc: "Mark M. Hoffman" Cc: Jean Delvare Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/hwmon/i5k_amb.c | 28 +++++++++++++++++++++++++++- 1 file changed, 27 insertions(+), 1 deletion(-) diff --git a/drivers/hwmon/i5k_amb.c b/drivers/hwmon/i5k_amb.c index f9e2ed621f7..2ede9388096 100644 --- a/drivers/hwmon/i5k_amb.c +++ b/drivers/hwmon/i5k_amb.c @@ -81,6 +81,8 @@ static unsigned long amb_reg_temp(unsigned int amb) #define MAX_AMBS_PER_CHANNEL 16 #define MAX_AMBS (MAX_MEM_CHANNELS * \ MAX_AMBS_PER_CHANNEL) +#define CHANNEL_SHIFT 4 +#define DIMM_MASK 0xF /* * Ugly hack: For some reason the highest bit is set if there * are _any_ DIMMs in the channel. Attempting to read from @@ -89,7 +91,7 @@ static unsigned long amb_reg_temp(unsigned int amb) * might prevent us from seeing the 16th DIMM in the channel. */ #define REAL_MAX_AMBS_PER_CHANNEL 15 -#define KNOBS_PER_AMB 5 +#define KNOBS_PER_AMB 6 static unsigned long amb_num_from_reg(unsigned int byte_num, unsigned int bit) { @@ -238,6 +240,16 @@ static ssize_t show_amb_temp(struct device *dev, 500 * amb_read_byte(data, amb_reg_temp(attr->index))); } +static ssize_t show_label(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + + return sprintf(buf, "Ch. %d DIMM %d\n", attr->index >> CHANNEL_SHIFT, + attr->index & DIMM_MASK); +} + static int __devinit i5k_amb_hwmon_init(struct platform_device *pdev) { int i, j, k, d = 0; @@ -268,6 +280,20 @@ static int __devinit i5k_amb_hwmon_init(struct platform_device *pdev) continue; d++; + /* sysfs label */ + iattr = data->attrs + data->num_attrs; + snprintf(iattr->name, AMB_SYSFS_NAME_LEN, + "temp%d_label", d); + iattr->s_attr.dev_attr.attr.name = iattr->name; + iattr->s_attr.dev_attr.attr.mode = S_IRUGO; + iattr->s_attr.dev_attr.show = show_label; + iattr->s_attr.index = k; + res = device_create_file(&pdev->dev, + &iattr->s_attr.dev_attr); + if (res) + goto exit_remove; + data->num_attrs++; + /* Temperature sysfs knob */ iattr = data->attrs + data->num_attrs; snprintf(iattr->name, AMB_SYSFS_NAME_LEN, -- GitLab From 249e3c85afb972d8ae8b6da269e7c85f931b9849 Mon Sep 17 00:00:00 2001 From: Alistair John Strachan Date: Fri, 15 Aug 2008 00:40:37 -0700 Subject: [PATCH 428/750] abituguru3: update MAINTAINERS Hans passed maintainership of the abituguru3 hwmon driver onto me. Add a new entry to the MAINTAINERS file for the abituguru3 driver and assign it to me. Also update the existing UGURU entry to indicate that Hans is only responsible for the abituguru driver. Signed-off-by: Alistair John Strachan Acked-by: Hans de Goede Cc: Jean Delvare Cc: "Mark M. Hoffman" Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/MAINTAINERS b/MAINTAINERS index 4c5e9fe0f7d..74092c9b568 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -175,12 +175,18 @@ M: bcrl@kvack.org L: linux-aio@kvack.org S: Supported -ABIT UGURU HARDWARE MONITOR DRIVER +ABIT UGURU 1,2 HARDWARE MONITOR DRIVER P: Hans de Goede M: j.w.r.degoede@hhs.nl L: lm-sensors@lm-sensors.org S: Maintained +ABIT UGURU 3 HARDWARE MONITOR DRIVER +P: Alistair John Strachan +M: alistair@devzero.co.uk +L: lm-sensors@lm-sensors.org +S: Maintained + ACENIC DRIVER P: Jes Sorensen M: jes@trained-monkey.org -- GitLab From 4ef664b5bc93bbfe28513165216a8c9f4fad5314 Mon Sep 17 00:00:00 2001 From: Alistair John Strachan Date: Fri, 15 Aug 2008 00:40:39 -0700 Subject: [PATCH 429/750] abituguru3: prefer DMI probing to manual probing Previously the driver was only using DMI to prevent smbus probing on non-Abit motherboards. However, since the manual probing method is brittle and prone to failure on some Abit motherboards (esp. the Abit IP35 Pro) it is better to use DMI to also read the board name and then decide whether or not to probe the bus. At the moment, we do not have a list of valid DMI name strings to use for existing and supported motherboards. This patch only implements DMI probing for the IP35 Pro. For motherboards that can not yet use DMI probing, a warning will be printed to the kernel log asking those users to email me their dmidecode output. The existing manual probing mechanism will be used if CONFIG_DMI is not enabled, if DMI probing fails (for DMI-unsupported motherboards), or if DMI probing fails and the "force" option is set (for DMI-supported motherboards). Ideally in the longer term this manual probing method would be removed. This patch should be safe to apply as it does not change the probing behaviour for most of the supported motherboards, just the IP35 Pro, which already has regressions filed against it in 2.6.26. Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11212 Signed-off-by: Alistair John Strachan Acked-by: Hans de Goede Cc: "Mark M. Hoffman" Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/hwmon/abituguru3.c | 134 ++++++++++++++++++++++++++----------- 1 file changed, 94 insertions(+), 40 deletions(-) diff --git a/drivers/hwmon/abituguru3.c b/drivers/hwmon/abituguru3.c index f00f497b9ca..d568c65c137 100644 --- a/drivers/hwmon/abituguru3.c +++ b/drivers/hwmon/abituguru3.c @@ -1,5 +1,8 @@ /* - abituguru3.c Copyright (c) 2006 Hans de Goede + abituguru3.c + + Copyright (c) 2006-2008 Hans de Goede + Copyright (c) 2008 Alistair John Strachan This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by @@ -116,7 +119,7 @@ struct abituguru3_sensor_info { struct abituguru3_motherboard_info { u16 id; - const char *name; + const char *dmi_name; /* + 1 -> end of sensors indicated by a sensor with name == NULL */ struct abituguru3_sensor_info sensors[ABIT_UGURU3_MAX_NO_SENSORS + 1]; }; @@ -161,7 +164,7 @@ struct abituguru3_data { /* Constants */ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { - { 0x000C, "unknown", { + { 0x000C, NULL /* Unknown, need DMI string */, { { "CPU Core", 0, 0, 10, 1, 0 }, { "DDR", 1, 0, 10, 1, 0 }, { "DDR VTT", 2, 0, 10, 1, 0 }, @@ -183,7 +186,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { { "AUX1 Fan", 35, 2, 60, 1, 0 }, { NULL, 0, 0, 0, 0, 0 } } }, - { 0x000D, "Abit AW8", { + { 0x000D, NULL /* Abit AW8, need DMI string */, { { "CPU Core", 0, 0, 10, 1, 0 }, { "DDR", 1, 0, 10, 1, 0 }, { "DDR VTT", 2, 0, 10, 1, 0 }, @@ -212,7 +215,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { { "AUX5 Fan", 39, 2, 60, 1, 0 }, { NULL, 0, 0, 0, 0, 0 } } }, - { 0x000E, "AL-8", { + { 0x000E, NULL /* AL-8, need DMI string */, { { "CPU Core", 0, 0, 10, 1, 0 }, { "DDR", 1, 0, 10, 1, 0 }, { "DDR VTT", 2, 0, 10, 1, 0 }, @@ -233,7 +236,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { { "SYS Fan", 34, 2, 60, 1, 0 }, { NULL, 0, 0, 0, 0, 0 } } }, - { 0x000F, "unknown", { + { 0x000F, NULL /* Unknown, need DMI string */, { { "CPU Core", 0, 0, 10, 1, 0 }, { "DDR", 1, 0, 10, 1, 0 }, { "DDR VTT", 2, 0, 10, 1, 0 }, @@ -254,7 +257,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { { "SYS Fan", 34, 2, 60, 1, 0 }, { NULL, 0, 0, 0, 0, 0 } } }, - { 0x0010, "Abit NI8 SLI GR", { + { 0x0010, NULL /* Abit NI8 SLI GR, need DMI string */, { { "CPU Core", 0, 0, 10, 1, 0 }, { "DDR", 1, 0, 10, 1, 0 }, { "DDR VTT", 2, 0, 10, 1, 0 }, @@ -276,7 +279,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { { "OTES1 Fan", 36, 2, 60, 1, 0 }, { NULL, 0, 0, 0, 0, 0 } } }, - { 0x0011, "Abit AT8 32X", { + { 0x0011, NULL /* Abit AT8 32X, need DMI string */, { { "CPU Core", 0, 0, 10, 1, 0 }, { "DDR", 1, 0, 20, 1, 0 }, { "DDR VTT", 2, 0, 10, 1, 0 }, @@ -302,7 +305,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { { "AUX2 Fan", 36, 2, 60, 1, 0 }, { NULL, 0, 0, 0, 0, 0 } } }, - { 0x0012, "Abit AN8 32X", { + { 0x0012, NULL /* Abit AN8 32X, need DMI string */, { { "CPU Core", 0, 0, 10, 1, 0 }, { "DDR", 1, 0, 20, 1, 0 }, { "DDR VTT", 2, 0, 10, 1, 0 }, @@ -324,7 +327,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { { "AUX1 Fan", 36, 2, 60, 1, 0 }, { NULL, 0, 0, 0, 0, 0 } } }, - { 0x0013, "Abit AW8D", { + { 0x0013, NULL /* Abit AW8D, need DMI string */, { { "CPU Core", 0, 0, 10, 1, 0 }, { "DDR", 1, 0, 10, 1, 0 }, { "DDR VTT", 2, 0, 10, 1, 0 }, @@ -353,7 +356,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { { "AUX5 Fan", 39, 2, 60, 1, 0 }, { NULL, 0, 0, 0, 0, 0 } } }, - { 0x0014, "Abit AB9 Pro", { + { 0x0014, NULL /* Abit AB9 Pro, need DMI string */, { { "CPU Core", 0, 0, 10, 1, 0 }, { "DDR", 1, 0, 10, 1, 0 }, { "DDR VTT", 2, 0, 10, 1, 0 }, @@ -374,7 +377,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { { "SYS Fan", 34, 2, 60, 1, 0 }, { NULL, 0, 0, 0, 0, 0 } } }, - { 0x0015, "unknown", { + { 0x0015, NULL /* Unknown, need DMI string */, { { "CPU Core", 0, 0, 10, 1, 0 }, { "DDR", 1, 0, 20, 1, 0 }, { "DDR VTT", 2, 0, 10, 1, 0 }, @@ -398,7 +401,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { { "AUX3 Fan", 36, 2, 60, 1, 0 }, { NULL, 0, 0, 0, 0, 0 } } }, - { 0x0016, "AW9D-MAX", { + { 0x0016, NULL /* AW9D-MAX, need DMI string */, { { "CPU Core", 0, 0, 10, 1, 0 }, { "DDR2", 1, 0, 20, 1, 0 }, { "DDR2 VTT", 2, 0, 10, 1, 0 }, @@ -426,7 +429,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { { "OTES1 Fan", 38, 2, 60, 1, 0 }, { NULL, 0, 0, 0, 0, 0 } } }, - { 0x0017, "unknown", { + { 0x0017, NULL /* Unknown, need DMI string */, { { "CPU Core", 0, 0, 10, 1, 0 }, { "DDR2", 1, 0, 20, 1, 0 }, { "DDR2 VTT", 2, 0, 10, 1, 0 }, @@ -451,7 +454,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { { "AUX3 FAN", 37, 2, 60, 1, 0 }, { NULL, 0, 0, 0, 0, 0 } } }, - { 0x0018, "unknown", { + { 0x0018, NULL /* Unknown, need DMI string */, { { "CPU Core", 0, 0, 10, 1, 0 }, { "DDR2", 1, 0, 20, 1, 0 }, { "DDR2 VTT", 2, 0, 10, 1, 0 }, @@ -478,7 +481,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { { "AUX3 Fan", 36, 2, 60, 1, 0 }, { NULL, 0, 0, 0, 0, 0 } } }, - { 0x0019, "unknown", { + { 0x0019, NULL /* Unknown, need DMI string */, { { "CPU Core", 7, 0, 10, 1, 0 }, { "DDR2", 13, 0, 20, 1, 0 }, { "DDR2 VTT", 14, 0, 10, 1, 0 }, @@ -505,7 +508,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { { "AUX3 FAN", 36, 2, 60, 1, 0 }, { NULL, 0, 0, 0, 0, 0 } } }, - { 0x001A, "Abit IP35 Pro", { + { 0x001A, "IP35 Pro(Intel P35-ICH9R)", { { "CPU Core", 0, 0, 10, 1, 0 }, { "DDR2", 1, 0, 20, 1, 0 }, { "DDR2 VTT", 2, 0, 10, 1, 0 }, @@ -533,7 +536,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { { "AUX4 Fan", 37, 2, 60, 1, 0 }, { NULL, 0, 0, 0, 0, 0 } } }, - { 0x001B, "unknown", { + { 0x001B, NULL /* Unknown, need DMI string */, { { "CPU Core", 0, 0, 10, 1, 0 }, { "DDR3", 1, 0, 20, 1, 0 }, { "DDR3 VTT", 2, 0, 10, 1, 0 }, @@ -560,7 +563,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { { "AUX3 Fan", 36, 2, 60, 1, 0 }, { NULL, 0, 0, 0, 0, 0 } } }, - { 0x001C, "unknown", { + { 0x001C, NULL /* Unknown, need DMI string */, { { "CPU Core", 0, 0, 10, 1, 0 }, { "DDR2", 1, 0, 20, 1, 0 }, { "DDR2 VTT", 2, 0, 10, 1, 0 }, @@ -935,9 +938,18 @@ static int __devinit abituguru3_probe(struct platform_device *pdev) goto abituguru3_probe_error; } data->sensors = abituguru3_motherboards[i].sensors; + printk(KERN_INFO ABIT_UGURU3_NAME ": found Abit uGuru3, motherboard " - "ID: %04X (%s)\n", (unsigned int)id, - abituguru3_motherboards[i].name); + "ID: %04X\n", (unsigned int)id); + +#ifdef CONFIG_DMI + if (!abituguru3_motherboards[i].dmi_name) { + printk(KERN_WARNING ABIT_UGURU3_NAME ": this motherboard was " + "not detected using DMI. Please send the output of " + "\"dmidecode\" to the abituguru3 maintainer" + "(see MAINTAINERS)\n"); + } +#endif /* Fill the sysfs attr array */ sysfs_attr_i = 0; @@ -1109,6 +1121,46 @@ static struct platform_driver abituguru3_driver = { .resume = abituguru3_resume }; +#ifdef CONFIG_DMI + +static int __init abituguru3_dmi_detect(void) +{ + const char *board_vendor, *board_name; + int i, err = (force) ? 1 : -ENODEV; + + board_vendor = dmi_get_system_info(DMI_BOARD_VENDOR); + if (!board_vendor || strcmp(board_vendor, "http://www.abit.com.tw/")) + return err; + + board_name = dmi_get_system_info(DMI_BOARD_NAME); + if (!board_name) + return err; + + for (i = 0; abituguru3_motherboards[i].id; i++) { + const char *dmi_name = abituguru3_motherboards[i].dmi_name; + if (dmi_name && !strcmp(dmi_name, board_name)) + break; + } + + if (!abituguru3_motherboards[i].id) + return 1; + + return 0; +} + +#else /* !CONFIG_DMI */ + +static inline int abituguru3_dmi_detect(void) +{ + return -ENODEV; +} + +#endif /* CONFIG_DMI */ + +/* FIXME: Manual detection should die eventually; we need to collect stable + * DMI model names first before we can rely entirely on CONFIG_DMI. + */ + static int __init abituguru3_detect(void) { /* See if there is an uguru3 there. An idle uGuru3 will hold 0x00 or @@ -1119,7 +1171,7 @@ static int __init abituguru3_detect(void) if (((data_val == 0x00) || (data_val == 0x08)) && ((cmd_val == 0xAC) || (cmd_val == 0x05) || (cmd_val == 0x55))) - return ABIT_UGURU3_BASE; + return 0; ABIT_UGURU3_DEBUG("no Abit uGuru3 found, data = 0x%02X, cmd = " "0x%02X\n", (unsigned int)data_val, (unsigned int)cmd_val); @@ -1127,7 +1179,7 @@ static int __init abituguru3_detect(void) if (force) { printk(KERN_INFO ABIT_UGURU3_NAME ": Assuming Abit uGuru3 is " "present because of \"force\" parameter\n"); - return ABIT_UGURU3_BASE; + return 0; } /* No uGuru3 found */ @@ -1138,27 +1190,29 @@ static struct platform_device *abituguru3_pdev; static int __init abituguru3_init(void) { - int address, err; struct resource res = { .flags = IORESOURCE_IO }; - -#ifdef CONFIG_DMI - const char *board_vendor = dmi_get_system_info(DMI_BOARD_VENDOR); - - /* safety check, refuse to load on non Abit motherboards */ - if (!force && (!board_vendor || - strcmp(board_vendor, "http://www.abit.com.tw/"))) - return -ENODEV; -#endif - - address = abituguru3_detect(); - if (address < 0) - return address; + int err; + + /* Attempt DMI detection first */ + err = abituguru3_dmi_detect(); + if (err < 0) + return err; + + /* Fall back to manual detection if there was no exact + * board name match, or force was specified. + */ + if (err > 0) { + err = abituguru3_detect(); + if (err) + return err; + } err = platform_driver_register(&abituguru3_driver); if (err) goto exit; - abituguru3_pdev = platform_device_alloc(ABIT_UGURU3_NAME, address); + abituguru3_pdev = platform_device_alloc(ABIT_UGURU3_NAME, + ABIT_UGURU3_BASE); if (!abituguru3_pdev) { printk(KERN_ERR ABIT_UGURU3_NAME ": Device allocation failed\n"); @@ -1166,8 +1220,8 @@ static int __init abituguru3_init(void) goto exit_driver_unregister; } - res.start = address; - res.end = address + ABIT_UGURU3_REGION_LENGTH - 1; + res.start = ABIT_UGURU3_BASE; + res.end = ABIT_UGURU3_BASE + ABIT_UGURU3_REGION_LENGTH - 1; res.name = ABIT_UGURU3_NAME; err = platform_device_add_resources(abituguru3_pdev, &res, 1); -- GitLab From eb93b7df7e66597fa807e34a0f812ffff7ff165b Mon Sep 17 00:00:00 2001 From: "Darrick J. Wong" Date: Fri, 15 Aug 2008 00:40:40 -0700 Subject: [PATCH 430/750] ibmaem: update the documentation to reflect the current name Minor documentation update to reflect the current full name of the power management hardware interface and reflows the text a bit. Signed-off-by: Darrick J. Wong Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/hwmon/ibmaem | 33 +++++++++++++++++---------------- drivers/hwmon/ibmaem.c | 6 +++--- 2 files changed, 20 insertions(+), 19 deletions(-) diff --git a/Documentation/hwmon/ibmaem b/Documentation/hwmon/ibmaem index 2fefaf582a4..e98bdfea346 100644 --- a/Documentation/hwmon/ibmaem +++ b/Documentation/hwmon/ibmaem @@ -1,8 +1,11 @@ Kernel driver ibmaem ====================== +This driver talks to the IBM Systems Director Active Energy Manager, known +henceforth as AEM. + Supported systems: - * Any recent IBM System X server with Active Energy Manager support. + * Any recent IBM System X server with AEM support. This includes the x3350, x3550, x3650, x3655, x3755, x3850 M2, x3950 M2, and certain HS2x/LS2x/QS2x blades. The IPMI host interface driver ("ipmi-si") needs to be loaded for this driver to do anything. @@ -14,24 +17,22 @@ Author: Darrick J. Wong Description ----------- -This driver implements sensor reading support for the energy and power -meters available on various IBM System X hardware through the BMC. All -sensor banks will be exported as platform devices; this driver can talk -to both v1 and v2 interfaces. This driver is completely separate from the -older ibmpex driver. +This driver implements sensor reading support for the energy and power meters +available on various IBM System X hardware through the BMC. All sensor banks +will be exported as platform devices; this driver can talk to both v1 and v2 +interfaces. This driver is completely separate from the older ibmpex driver. -The v1 AEM interface has a simple set of features to monitor energy use. -There is a register that displays an estimate of raw energy consumption -since the last BMC reset, and a power sensor that returns average power -use over a configurable interval. +The v1 AEM interface has a simple set of features to monitor energy use. There +is a register that displays an estimate of raw energy consumption since the +last BMC reset, and a power sensor that returns average power use over a +configurable interval. -The v2 AEM interface is a bit more sophisticated, being able to present -a wider range of energy and power use registers, the power cap as -set by the AEM software, and temperature sensors. +The v2 AEM interface is a bit more sophisticated, being able to present a wider +range of energy and power use registers, the power cap as set by the AEM +software, and temperature sensors. Special Features ---------------- -The "power_cap" value displays the current system power cap, as set by -the Active Energy Manager software. Setting the power cap from the host -is not currently supported. +The "power_cap" value displays the current system power cap, as set by the AEM +software. Setting the power cap from the host is not currently supported. diff --git a/drivers/hwmon/ibmaem.c b/drivers/hwmon/ibmaem.c index c9416e65748..5e4775a62f6 100644 --- a/drivers/hwmon/ibmaem.c +++ b/drivers/hwmon/ibmaem.c @@ -1,6 +1,6 @@ /* - * A hwmon driver for the IBM Active Energy Manager temperature/power sensors - * and capping functionality. + * A hwmon driver for the IBM System Director Active Energy Manager (AEM) + * temperature/power/energy sensors and capping functionality. * Copyright (C) 2008 IBM * * Author: Darrick J. Wong @@ -1104,7 +1104,7 @@ static void __exit aem_exit(void) } MODULE_AUTHOR("Darrick J. Wong "); -MODULE_DESCRIPTION("IBM Active Energy Manager power/temp sensor driver"); +MODULE_DESCRIPTION("IBM AEM power/temp/energy sensor driver"); MODULE_LICENSE("GPL"); module_init(aem_init); -- GitLab From 9c5413eac5199b8457689eb2c9d9e75138356bd6 Mon Sep 17 00:00:00 2001 From: "Darrick J. Wong" Date: Fri, 15 Aug 2008 00:40:40 -0700 Subject: [PATCH 431/750] ibmaem: prevent infinite probing loop on x3650 M2 systems On older machines, probing for a nonexistent AEM interface returned an IPMI error; when we saw this, we'd stop probing. On the x3650 M2 and (presumably) later, we are returned a value indicating success and a buffer full of garbage or zeroes. This causes the probe function to run in an infinite loop. To fix this, we add one last check--if the interface number we're looking for is higher than the number of interfaces that AEM claims to have, stop probing. Signed-off-by: Darrick J. Wong Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/hwmon/ibmaem.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/hwmon/ibmaem.c b/drivers/hwmon/ibmaem.c index 5e4775a62f6..08c5179e6d8 100644 --- a/drivers/hwmon/ibmaem.c +++ b/drivers/hwmon/ibmaem.c @@ -676,7 +676,8 @@ static int aem_find_aem2(struct aem_ipmi_data *data, return -ETIMEDOUT; if (data->rx_result || data->rx_msg_len != sizeof(*fi_resp) || - memcmp(&fi_resp->id, &system_x_id, sizeof(system_x_id))) + memcmp(&fi_resp->id, &system_x_id, sizeof(system_x_id)) || + fi_resp->num_instances <= instance_num) return -ENOENT; return 0; -- GitLab From bb15e7f286e3ecf3e85e06ad9b0019096e43a613 Mon Sep 17 00:00:00 2001 From: "Darrick J. Wong" Date: Fri, 15 Aug 2008 00:40:41 -0700 Subject: [PATCH 432/750] ibmaem: don't query the entire sensor repository when reading energy meter Currently, all sensors are read when the energy meter is queried via sysfs. This introduces a considerable amount of delay and variation in the sysfs reading, which is not desirable when trying to profile energy use. Therefore, read only the energy meters when a sysfs query comes in for them, and don't cache the results so that we always get the latest reading. Signed-off-by: Darrick J. Wong Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/hwmon/ibmaem.c | 18 +++++++++++++----- 1 file changed, 13 insertions(+), 5 deletions(-) diff --git a/drivers/hwmon/ibmaem.c b/drivers/hwmon/ibmaem.c index 08c5179e6d8..0f70dc20410 100644 --- a/drivers/hwmon/ibmaem.c +++ b/drivers/hwmon/ibmaem.c @@ -463,12 +463,18 @@ static int aem_read_sensor(struct aem_data *data, u8 elt, u8 reg, } /* Update AEM energy registers */ +static void update_aem_energy_one(struct aem_data *data, int which) +{ + aem_read_sensor(data, AEM_ENERGY_ELEMENT, which, + &data->energy[which], 8); +} + static void update_aem_energy(struct aem_data *data) { - aem_read_sensor(data, AEM_ENERGY_ELEMENT, 0, &data->energy[0], 8); + update_aem_energy_one(data, 0); if (data->ver_major < 2) return; - aem_read_sensor(data, AEM_ENERGY_ELEMENT, 1, &data->energy[1], 8); + update_aem_energy_one(data, 1); } /* Update all AEM1 sensors */ @@ -850,7 +856,7 @@ static ssize_t aem_show_power(struct device *dev, struct timespec b, a; mutex_lock(&data->lock); - update_aem_energy(data); + update_aem_energy_one(data, attr->index); getnstimeofday(&b); before = data->energy[attr->index]; @@ -862,7 +868,7 @@ static ssize_t aem_show_power(struct device *dev, return 0; } - update_aem_energy(data); + update_aem_energy_one(data, attr->index); getnstimeofday(&a); after = data->energy[attr->index]; mutex_unlock(&data->lock); @@ -881,7 +887,9 @@ static ssize_t aem_show_energy(struct device *dev, { struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); struct aem_data *a = dev_get_drvdata(dev); - a->update(a); + mutex_lock(&a->lock); + update_aem_energy_one(a, attr->index); + mutex_unlock(&a->lock); return sprintf(buf, "%llu\n", (unsigned long long)a->energy[attr->index] * 1000); -- GitLab From 34c86c1e622ec77ba81c01969003bbc8e15156f3 Mon Sep 17 00:00:00 2001 From: "Darrick J. Wong" Date: Fri, 15 Aug 2008 00:40:41 -0700 Subject: [PATCH 433/750] coretemp: recognize Nehalem CPUs Add in the CPUID for Nehalem chips. Signed-off-by: Darrick J. Wong Cc: Kent Liu Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/hwmon/coretemp.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/hwmon/coretemp.c b/drivers/hwmon/coretemp.c index 70239acecc8..93c17223b52 100644 --- a/drivers/hwmon/coretemp.c +++ b/drivers/hwmon/coretemp.c @@ -413,10 +413,11 @@ static int __init coretemp_init(void) for_each_online_cpu(i) { struct cpuinfo_x86 *c = &cpu_data(i); - /* check if family 6, models 0xe, 0xf, 0x16, 0x17 */ + /* check if family 6, models 0xe, 0xf, 0x16, 0x17, 0x1A */ if ((c->cpuid_level < 0) || (c->x86 != 0x6) || !((c->x86_model == 0xe) || (c->x86_model == 0xf) || - (c->x86_model == 0x16) || (c->x86_model == 0x17))) { + (c->x86_model == 0x16) || (c->x86_model == 0x17) || + (c->x86_model == 0x1A))) { /* supported CPU not found, but report the unknown family 6 CPU */ -- GitLab From 75312619e8cd47265da210189cca57ab09640b18 Mon Sep 17 00:00:00 2001 From: Jack Steiner Date: Fri, 15 Aug 2008 00:40:42 -0700 Subject: [PATCH 434/750] MAINTAINERS: add maintainers for GRU, XPC, XPNET and XP Add MAINTAINERS for GRU, XPNET, XPC and XP drivers. Signed-off-by: Jack Steiner Cc: Stephen Rothwell Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index 74092c9b568..663485b004f 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -3754,6 +3754,16 @@ L: linux-visws-devel@lists.sf.net W: http://linux-visws.sf.net S: Maintained for 2.6. +SGI GRU DRIVER +P: Jack Steiner +M: steiner@sgi.com +S: Maintained + +SGI XP/XPC/XPNET DRIVER +P: Dean Nelson +M: dcn@sgi.com +S: Maintained + SIMTEC EB110ATX (Chalice CATS) P: Ben Dooks P: Vincent Sanders -- GitLab From 7d455e0030eeab820773e7786605be4d9e56a04b Mon Sep 17 00:00:00 2001 From: Chris Mason Date: Fri, 15 Aug 2008 00:40:43 -0700 Subject: [PATCH 435/750] fs/inode.c: properly init address_space->writeback_index write_cache_pages() uses i_mapping->writeback_index to pick up where it left off the last time a given inode was found by pdflush or balance_dirty_pages (or anyone else who sets wbc->range_cyclic) alloc_inode() should set it to a sane value so that writeback doesn't start in the middle of a file. It is somewhat difficult to notice the bug since write_cache_pages will loop around to the start of the file and the elevator helps hide the resulting seeks. For whatever reason, Btrfs hits this often. Unpatched, untarring 30 copies of the linux kernel in series runs at 47MB/s on a single sata drive. With this fix, it jumps to 62MB/s. Signed-off-by: Chris Mason Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- fs/inode.c | 1 + 1 file changed, 1 insertion(+) diff --git a/fs/inode.c b/fs/inode.c index b6726f64453..0487ddba139 100644 --- a/fs/inode.c +++ b/fs/inode.c @@ -166,6 +166,7 @@ static struct inode *alloc_inode(struct super_block *sb) mapping_set_gfp_mask(mapping, GFP_HIGHUSER_PAGECACHE); mapping->assoc_mapping = NULL; mapping->backing_dev_info = &default_backing_dev_info; + mapping->writeback_index = 0; /* * If the block_device provides a backing_dev_info for client -- GitLab From e48880e02e7e7ead9daa47fe3a20486f550668d3 Mon Sep 17 00:00:00 2001 From: David Brownell Date: Fri, 15 Aug 2008 00:40:44 -0700 Subject: [PATCH 436/750] spi: bugfix spi_add_device() with duplicate chipselects When reviewing a recent patch I noticed a potential trouble spot in the registration of new SPI devices. The SPI master driver is told to set the device up before adding it to the driver model, so that it's always properly set up when probe() is called. (This is important, because in the case of inverted chipselects, this device can make the bus misbehave until it's properly deselected. It's got to be set up even if no driver binds to the device.) The trouble spot is that it doesn't first verify that no other device has been added using that chipselect. If such a device has been added, its configuration gets trashed. (Fortunately this has not been a common error!) The fix here adds an explicit check, and a mutex to protect the relevant critical region. [akpm@linux-foundation.org: make the lock local to spi_add_device()] Signed-off-by: David Brownell Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/spi/spi.c | 40 +++++++++++++++++++++++++++++----------- 1 file changed, 29 insertions(+), 11 deletions(-) diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c index 964124b60db..75e86865234 100644 --- a/drivers/spi/spi.c +++ b/drivers/spi/spi.c @@ -226,10 +226,11 @@ EXPORT_SYMBOL_GPL(spi_alloc_device); * Companion function to spi_alloc_device. Devices allocated with * spi_alloc_device can be added onto the spi bus with this function. * - * Returns 0 on success; non-zero on failure + * Returns 0 on success; negative errno on failure */ int spi_add_device(struct spi_device *spi) { + static DEFINE_MUTEX(spi_add_lock); struct device *dev = spi->master->dev.parent; int status; @@ -246,26 +247,43 @@ int spi_add_device(struct spi_device *spi) "%s.%u", spi->master->dev.bus_id, spi->chip_select); - /* drivers may modify this initial i/o setup */ + + /* We need to make sure there's no other device with this + * chipselect **BEFORE** we call setup(), else we'll trash + * its configuration. Lock against concurrent add() calls. + */ + mutex_lock(&spi_add_lock); + + if (bus_find_device_by_name(&spi_bus_type, NULL, spi->dev.bus_id) + != NULL) { + dev_err(dev, "chipselect %d already in use\n", + spi->chip_select); + status = -EBUSY; + goto done; + } + + /* Drivers may modify this initial i/o setup, but will + * normally rely on the device being setup. Devices + * using SPI_CS_HIGH can't coexist well otherwise... + */ status = spi->master->setup(spi); if (status < 0) { dev_err(dev, "can't %s %s, status %d\n", "setup", spi->dev.bus_id, status); - return status; + goto done; } - /* driver core catches callers that misbehave by defining - * devices that already exist. - */ + /* Device may be bound to an active driver when this returns */ status = device_add(&spi->dev); - if (status < 0) { + if (status < 0) dev_err(dev, "can't %s %s, status %d\n", "add", spi->dev.bus_id, status); - return status; - } + else + dev_dbg(dev, "registered child %s\n", spi->dev.bus_id); - dev_dbg(dev, "registered child %s\n", spi->dev.bus_id); - return 0; +done: + mutex_unlock(&spi_add_lock); + return status; } EXPORT_SYMBOL_GPL(spi_add_device); -- GitLab From be4de35263f59ca1f4740edfffbfb02cc3f2189e Mon Sep 17 00:00:00 2001 From: Dave Chinner Date: Fri, 15 Aug 2008 00:40:44 -0700 Subject: [PATCH 437/750] completions: uninline try_wait_for_completion and completion_done m68k fails to build with these functions inlined in completion.h. Move them out of line into sched.c and export them to avoid this problem. Signed-off-by: Dave Chinner Cc: Geert Uytterhoeven Cc: Ingo Molnar Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- include/linux/completion.h | 46 ++------------------------------------ kernel/sched.c | 46 ++++++++++++++++++++++++++++++++++++++ 2 files changed, 48 insertions(+), 44 deletions(-) diff --git a/include/linux/completion.h b/include/linux/completion.h index 57faa60de9b..02ef8835999 100644 --- a/include/linux/completion.h +++ b/include/linux/completion.h @@ -49,6 +49,8 @@ extern unsigned long wait_for_completion_timeout(struct completion *x, unsigned long timeout); extern unsigned long wait_for_completion_interruptible_timeout( struct completion *x, unsigned long timeout); +extern bool try_wait_for_completion(struct completion *x); +extern bool completion_done(struct completion *x); extern void complete(struct completion *); extern void complete_all(struct completion *); @@ -56,48 +58,4 @@ extern void complete_all(struct completion *); #define INIT_COMPLETION(x) ((x).done = 0) -/** - * try_wait_for_completion - try to decrement a completion without blocking - * @x: completion structure - * - * Returns: 0 if a decrement cannot be done without blocking - * 1 if a decrement succeeded. - * - * If a completion is being used as a counting completion, - * attempt to decrement the counter without blocking. This - * enables us to avoid waiting if the resource the completion - * is protecting is not available. - */ -static inline bool try_wait_for_completion(struct completion *x) -{ - int ret = 1; - - spin_lock_irq(&x->wait.lock); - if (!x->done) - ret = 0; - else - x->done--; - spin_unlock_irq(&x->wait.lock); - return ret; -} - -/** - * completion_done - Test to see if a completion has any waiters - * @x: completion structure - * - * Returns: 0 if there are waiters (wait_for_completion() in progress) - * 1 if there are no waiters. - * - */ -static inline bool completion_done(struct completion *x) -{ - int ret = 1; - - spin_lock_irq(&x->wait.lock); - if (!x->done) - ret = 0; - spin_unlock_irq(&x->wait.lock); - return ret; -} - #endif diff --git a/kernel/sched.c b/kernel/sched.c index d601fb0406c..95e6ad3c231 100644 --- a/kernel/sched.c +++ b/kernel/sched.c @@ -4669,6 +4669,52 @@ int __sched wait_for_completion_killable(struct completion *x) } EXPORT_SYMBOL(wait_for_completion_killable); +/** + * try_wait_for_completion - try to decrement a completion without blocking + * @x: completion structure + * + * Returns: 0 if a decrement cannot be done without blocking + * 1 if a decrement succeeded. + * + * If a completion is being used as a counting completion, + * attempt to decrement the counter without blocking. This + * enables us to avoid waiting if the resource the completion + * is protecting is not available. + */ +bool try_wait_for_completion(struct completion *x) +{ + int ret = 1; + + spin_lock_irq(&x->wait.lock); + if (!x->done) + ret = 0; + else + x->done--; + spin_unlock_irq(&x->wait.lock); + return ret; +} +EXPORT_SYMBOL(try_wait_for_completion); + +/** + * completion_done - Test to see if a completion has any waiters + * @x: completion structure + * + * Returns: 0 if there are waiters (wait_for_completion() in progress) + * 1 if there are no waiters. + * + */ +bool completion_done(struct completion *x) +{ + int ret = 1; + + spin_lock_irq(&x->wait.lock); + if (!x->done) + ret = 0; + spin_unlock_irq(&x->wait.lock); + return ret; +} +EXPORT_SYMBOL(completion_done); + static long __sched sleep_on_common(wait_queue_head_t *q, int state, long timeout) { -- GitLab From c963343a1150106819773e828c9b237ed977615b Mon Sep 17 00:00:00 2001 From: Bob Copeland Date: Fri, 15 Aug 2008 00:40:46 -0700 Subject: [PATCH 438/750] omfs: fix potential oops when directory size is corrupted Testing with a modified fsfuzzer reveals a couple of locations in omfs where filesystem variables are ultimately used as loop counters with insufficient sanity checking. In this case, dir->i_size is used to compute the number of buckets in the directory hash. If too large, readdir will overrun a buffer. Since it's an invariant that dir->i_size is equal to the sysblock size, and we already sanity check that, just use that value instead. This fixes the following oops: BUG: unable to handle kernel paging request at c978e004 IP: [] omfs_readdir+0x18e/0x32f Oops: 0000 [#1] PREEMPT DEBUG_PAGEALLOC Modules linked in: Pid: 4796, comm: ls Not tainted (2.6.27-rc2 #12) EIP: 0060:[] EFLAGS: 00010287 CPU: 0 EIP is at omfs_readdir+0x18e/0x32f EAX: c978d000 EBX: 00000000 ECX: cbfcfaf8 EDX: cb2cf100 ESI: 00001000 EDI: 00000800 EBP: cb2d3f68 ESP: cb2d3f0c DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068 Process ls (pid: 4796, ti=cb2d3000 task=cb175f40 task.ti=cb2d3000) Stack: 00000002 00000000 00000000 c018a820 cb2d3f94 cb2cf100 cbfb0000 ffffff10 cbfb3b80 cbfcfaf8 000001c9 00000a09 00000000 00000000 00000000 cbfcfbc8 c9697000 cbfb3b80 22222222 00001000 c08e6cd0 cb2cf100 cbfb3b80 cb2d3f88 Call Trace: [] ? filldir64+0x0/0xcd [] ? vfs_readdir+0x56/0x82 [] ? filldir64+0x0/0xcd [] ? sys_getdents64+0x5e/0xa0 [] ? sysenter_do_call+0x12/0x31 ======================= Code: 00 89 f0 89 f3 0f ac f8 14 81 e3 ff ff 0f 00 48 8d 14 c5 b8 01 00 00 89 45 cc 89 55 f0 e9 8c 01 00 00 8b 4d c8 8b 75 f0 8b 41 18 <8b> 54 30 04 8b 04 30 31 f6 89 5d dc 89 d1 8b 55 b8 0f c8 0f c9 Reported-by: Eric Sesterhenn Signed-off-by: Bob Copeland Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- fs/omfs/inode.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/fs/omfs/inode.c b/fs/omfs/inode.c index a95fe5984f4..d29047b1b9b 100644 --- a/fs/omfs/inode.c +++ b/fs/omfs/inode.c @@ -232,8 +232,7 @@ struct inode *omfs_iget(struct super_block *sb, ino_t ino) inode->i_mode = S_IFDIR | (S_IRWXUGO & ~sbi->s_dmask); inode->i_op = &omfs_dir_inops; inode->i_fop = &omfs_dir_operations; - inode->i_size = be32_to_cpu(oi->i_head.h_body_size) + - sizeof(struct omfs_header); + inode->i_size = sbi->s_sys_blocksize; inc_nlink(inode); break; case OMFS_FILE: -- GitLab From 9419fc1c957d600093baaea247fef23cca3b4e93 Mon Sep 17 00:00:00 2001 From: Bob Copeland Date: Fri, 15 Aug 2008 00:40:47 -0700 Subject: [PATCH 439/750] omfs: fix oops when file metadata is corrupted A fuzzed fileystem image failed with OMFS when the extent count was used in a loop without being checked against the max number of extents. It also provoked a signed division for an array index that was checked as if unsigned, leading to index by -1. omfsck will be updated to fix these cases, in the meantime bail out gracefully. Reported-by: Eric Sesterhenn Signed-off-by: Bob Copeland Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- fs/omfs/bitmap.c | 5 +++-- fs/omfs/file.c | 33 ++++++++++++++++++++++++++------- 2 files changed, 29 insertions(+), 9 deletions(-) diff --git a/fs/omfs/bitmap.c b/fs/omfs/bitmap.c index 697663b01ba..e1c0ec0ae98 100644 --- a/fs/omfs/bitmap.c +++ b/fs/omfs/bitmap.c @@ -92,7 +92,7 @@ int omfs_allocate_block(struct super_block *sb, u64 block) struct buffer_head *bh; struct omfs_sb_info *sbi = OMFS_SB(sb); int bits_per_entry = 8 * sb->s_blocksize; - int map, bit; + unsigned int map, bit; int ret = 0; u64 tmp; @@ -176,7 +176,8 @@ int omfs_clear_range(struct super_block *sb, u64 block, int count) struct omfs_sb_info *sbi = OMFS_SB(sb); int bits_per_entry = 8 * sb->s_blocksize; u64 tmp; - int map, bit, ret; + unsigned int map, bit; + int ret; tmp = block; bit = do_div(tmp, bits_per_entry); diff --git a/fs/omfs/file.c b/fs/omfs/file.c index 7e2499053e4..834b2331f6b 100644 --- a/fs/omfs/file.c +++ b/fs/omfs/file.c @@ -26,6 +26,13 @@ static int omfs_sync_file(struct file *file, struct dentry *dentry, return err ? -EIO : 0; } +static u32 omfs_max_extents(struct omfs_sb_info *sbi, int offset) +{ + return (sbi->s_sys_blocksize - offset - + sizeof(struct omfs_extent)) / + sizeof(struct omfs_extent_entry) + 1; +} + void omfs_make_empty_table(struct buffer_head *bh, int offset) { struct omfs_extent *oe = (struct omfs_extent *) &bh->b_data[offset]; @@ -45,6 +52,7 @@ int omfs_shrink_inode(struct inode *inode) struct buffer_head *bh; u64 next, last; u32 extent_count; + u32 max_extents; int ret; /* traverse extent table, freeing each entry that is greater @@ -62,15 +70,18 @@ int omfs_shrink_inode(struct inode *inode) goto out; oe = (struct omfs_extent *)(&bh->b_data[OMFS_EXTENT_START]); + max_extents = omfs_max_extents(sbi, OMFS_EXTENT_START); for (;;) { - if (omfs_is_bad(sbi, (struct omfs_header *) bh->b_data, next)) { - brelse(bh); - goto out; - } + if (omfs_is_bad(sbi, (struct omfs_header *) bh->b_data, next)) + goto out_brelse; extent_count = be32_to_cpu(oe->e_extent_count); + + if (extent_count > max_extents) + goto out_brelse; + last = next; next = be64_to_cpu(oe->e_next); entry = &oe->e_entry; @@ -98,10 +109,14 @@ int omfs_shrink_inode(struct inode *inode) if (!bh) goto out; oe = (struct omfs_extent *) (&bh->b_data[OMFS_EXTENT_CONT]); + max_extents = omfs_max_extents(sbi, OMFS_EXTENT_CONT); } ret = 0; out: return ret; +out_brelse: + brelse(bh); + return ret; } static void omfs_truncate(struct inode *inode) @@ -154,9 +169,7 @@ static int omfs_grow_extent(struct inode *inode, struct omfs_extent *oe, goto out; } } - max_count = (sbi->s_sys_blocksize - OMFS_EXTENT_START - - sizeof(struct omfs_extent)) / - sizeof(struct omfs_extent_entry) + 1; + max_count = omfs_max_extents(sbi, OMFS_EXTENT_START); /* TODO: add a continuation block here */ if (be32_to_cpu(oe->e_extent_count) > max_count-1) @@ -225,6 +238,7 @@ static int omfs_get_block(struct inode *inode, sector_t block, sector_t next, offset; int ret; u64 new_block; + u32 max_extents; int extent_count; struct omfs_extent *oe; struct omfs_extent_entry *entry; @@ -238,6 +252,7 @@ static int omfs_get_block(struct inode *inode, sector_t block, goto out; oe = (struct omfs_extent *)(&bh->b_data[OMFS_EXTENT_START]); + max_extents = omfs_max_extents(sbi, OMFS_EXTENT_START); next = inode->i_ino; for (;;) { @@ -249,6 +264,9 @@ static int omfs_get_block(struct inode *inode, sector_t block, next = be64_to_cpu(oe->e_next); entry = &oe->e_entry; + if (extent_count > max_extents) + goto out_brelse; + offset = find_block(inode, entry, block, extent_count, &remain); if (offset > 0) { ret = 0; @@ -266,6 +284,7 @@ static int omfs_get_block(struct inode *inode, sector_t block, if (!bh) goto out; oe = (struct omfs_extent *) (&bh->b_data[OMFS_EXTENT_CONT]); + max_extents = omfs_max_extents(sbi, OMFS_EXTENT_CONT); } if (create) { ret = omfs_grow_extent(inode, oe, &new_block); -- GitLab From 436a74593c34275807fadef20344bbaca251b8d1 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Fri, 15 Aug 2008 16:22:32 +0100 Subject: [PATCH 440/750] ALSA: wm8990: Fix routing of left DAC to speaker mixer Signed-off-by: Mark Brown Signed-off-by: Takashi Iwai --- sound/soc/codecs/wm8990.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/codecs/wm8990.c b/sound/soc/codecs/wm8990.c index 3ecce5168e9..9505a18fa60 100644 --- a/sound/soc/codecs/wm8990.c +++ b/sound/soc/codecs/wm8990.c @@ -920,7 +920,7 @@ static const struct snd_soc_dapm_route audio_map[] = { {"SPKMIX", "SPKMIX Left Mixer PGA Switch", "LOPGA"}, {"SPKMIX", "SPKMIX Right Mixer PGA Switch", "ROPGA"}, {"SPKMIX", "SPKMIX Right DAC Switch", "Right DAC"}, - {"SPKMIX", "SPKMIX Left DAC Switch", "Right DAC"}, + {"SPKMIX", "SPKMIX Left DAC Switch", "Left DAC"}, /* LONMIX */ {"LONMIX", "LONMIX Left Mixer PGA Switch", "LOPGA"}, -- GitLab From 97bb8129e5deb3c0584391a5d2348966732e2233 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Fri, 15 Aug 2008 16:22:33 +0100 Subject: [PATCH 441/750] ALSA: wm8990: Implement speaker volume PGA The latest revisions of the WM8990 provide a programmable gain amplifier for the speaker - configure the register cache and implement controls for this. Older revisions of the device ignore writes to these controls. Signed-off-by: Mark Brown Signed-off-by: Takashi Iwai --- sound/soc/codecs/wm8990.c | 8 ++++++-- sound/soc/codecs/wm8990.h | 14 ++++++++++++-- 2 files changed, 18 insertions(+), 4 deletions(-) diff --git a/sound/soc/codecs/wm8990.c b/sound/soc/codecs/wm8990.c index 9505a18fa60..e44153fa38d 100644 --- a/sound/soc/codecs/wm8990.c +++ b/sound/soc/codecs/wm8990.c @@ -82,7 +82,7 @@ static const u16 wm8990_reg[] = { 0x0003, /* R35 - ClassD1 */ 0x0000, /* R36 */ 0x0100, /* R37 - ClassD3 */ - 0x0000, /* R38 */ + 0x0079, /* R38 - ClassD4 */ 0x0000, /* R39 - Input Mixer1 */ 0x0000, /* R40 - Input Mixer2 */ 0x0000, /* R41 - Input Mixer3 */ @@ -311,11 +311,15 @@ SOC_SINGLE("Speaker Mode Switch", WM8990_CLASSD1, WM8990_CDMODE_BIT, 1, 0), SOC_SINGLE("Speaker Output Attenuation Volume", WM8990_SPEAKER_VOLUME, - WM8990_SPKVOL_SHIFT, WM8990_SPKVOL_MASK, 0), + WM8990_SPKATTN_SHIFT, WM8990_SPKATTN_MASK, 0), SOC_SINGLE("Speaker DC Boost Volume", WM8990_CLASSD3, WM8990_DCGAIN_SHIFT, WM8990_DCGAIN_MASK, 0), SOC_SINGLE("Speaker AC Boost Volume", WM8990_CLASSD3, WM8990_ACGAIN_SHIFT, WM8990_ACGAIN_MASK, 0), +SOC_SINGLE_TLV("Speaker Volume", WM8990_CLASSD4, + WM8990_SPKVOL_SHIFT, WM8990_SPKVOL_MASK, 0, out_pga_tlv), +SOC_SINGLE("Speaker ZC Switch", WM8990_CLASSD4, + WM8990_SPKZC_SHIFT, WM8990_SPKZC_MASK, 0), SOC_WM899X_OUTPGA_SINGLE_R_TLV("Left DAC Digital Volume", WM8990_LEFT_DAC_DIGITAL_VOLUME, diff --git a/sound/soc/codecs/wm8990.h b/sound/soc/codecs/wm8990.h index 6bea5748528..0a08325d544 100644 --- a/sound/soc/codecs/wm8990.h +++ b/sound/soc/codecs/wm8990.h @@ -54,6 +54,7 @@ #define WM8990_SPEAKER_VOLUME 0x22 #define WM8990_CLASSD1 0x23 #define WM8990_CLASSD3 0x25 +#define WM8990_CLASSD4 0x26 #define WM8990_INPUT_MIXER1 0x27 #define WM8990_INPUT_MIXER2 0x28 #define WM8990_INPUT_MIXER3 0x29 @@ -528,8 +529,8 @@ /* * R34 (0x22) - Speaker Volume */ -#define WM8990_SPKVOL_MASK 0x0003 /* SPKVOL - [1:0] */ -#define WM8990_SPKVOL_SHIFT 0 +#define WM8990_SPKATTN_MASK 0x0003 /* SPKATTN - [1:0] */ +#define WM8990_SPKATTN_SHIFT 0 /* * R35 (0x23) - ClassD1 @@ -544,6 +545,15 @@ #define WM8990_DCGAIN_SHIFT 3 #define WM8990_ACGAIN_MASK 0x0007 /* ACGAIN - [2:0] */ #define WM8990_ACGAIN_SHIFT 0 + +/* + * R38 (0x26) - ClassD4 + */ +#define WM8990_SPKZC_MASK 0x0001 /* SPKZC */ +#define WM8990_SPKZC_SHIFT 7 /* SPKZC */ +#define WM8990_SPKVOL_MASK 0x007F /* SPKVOL - [6:0] */ +#define WM8990_SPKVOL_SHIFT 0 /* SPKVOL - [6:0] */ + /* * R39 (0x27) - Input Mixer1 */ -- GitLab From 89499759dc0dd300528510f465b0bf532fc79a2a Mon Sep 17 00:00:00 2001 From: Seth Heasley Date: Mon, 11 Aug 2008 17:01:50 -0700 Subject: [PATCH 442/750] x86/PCI: irq and pci_ids patch for Intel Ibex Peak PCHs This patch adds the Intel Ibex Peak (PCH) LPC and SMBus Controller DeviceIDs. Signed-off-by: Seth Heasley Signed-off-by: Jesse Barnes --- arch/x86/pci/irq.c | 2 ++ include/linux/pci_ids.h | 3 +++ 2 files changed, 5 insertions(+) diff --git a/arch/x86/pci/irq.c b/arch/x86/pci/irq.c index fec0123b33a..8e077185e18 100644 --- a/arch/x86/pci/irq.c +++ b/arch/x86/pci/irq.c @@ -590,6 +590,8 @@ static __init int intel_router_probe(struct irq_router *r, struct pci_dev *route case PCI_DEVICE_ID_INTEL_ICH10_1: case PCI_DEVICE_ID_INTEL_ICH10_2: case PCI_DEVICE_ID_INTEL_ICH10_3: + case PCI_DEVICE_ID_INTEL_PCH_0: + case PCI_DEVICE_ID_INTEL_PCH_1: r->name = "PIIX/ICH"; r->get = pirq_piix_get; r->set = pirq_piix_set; diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h index 9ec2bcce8e8..f1624b39675 100644 --- a/include/linux/pci_ids.h +++ b/include/linux/pci_ids.h @@ -2428,6 +2428,9 @@ #define PCI_DEVICE_ID_INTEL_ICH10_3 0x3a1a #define PCI_DEVICE_ID_INTEL_ICH10_4 0x3a30 #define PCI_DEVICE_ID_INTEL_ICH10_5 0x3a60 +#define PCI_DEVICE_ID_INTEL_PCH_0 0x3b10 +#define PCI_DEVICE_ID_INTEL_PCH_1 0x3b11 +#define PCI_DEVICE_ID_INTEL_PCH_2 0x3b30 #define PCI_DEVICE_ID_INTEL_IOAT_SNB 0x402f #define PCI_DEVICE_ID_INTEL_5100_16 0x65f0 #define PCI_DEVICE_ID_INTEL_5100_21 0x65f5 -- GitLab From e213e87785559eaf3107897226817aea9291b06f Mon Sep 17 00:00:00 2001 From: Andi Kleen Date: Fri, 15 Aug 2008 18:12:47 +0200 Subject: [PATCH 443/750] x86: Fix ioremap off by one BUG Jean Delvare's machine triggered this BUG acpi_os_map_memory phys ffff0000 size 65535 ------------[ cut here ]------------ kernel BUG at arch/x86/mm/pat.c:233! with ACPI in the backtrace. Adding some debugging output showed that ACPI calls acpi_os_map_memory phys ffff0000 size 65535 And ioremap/PAT does this check in 32bit, so addr+size wraps and the BUG in reserve_memtype() triggers incorrectly. BUG_ON(start >= end); /* end is exclusive */ But reserve_memtype already uses u64: int reserve_memtype(u64 start, u64 end, so the 32bit truncation must happen in the caller. Presumably in ioremap when it passes this information to reserve_memtype(). This patch does this computation in 64bit. http://bugzilla.kernel.org/show_bug.cgi?id=11346 Signed-off-by: Andi Kleen --- arch/x86/mm/ioremap.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/mm/ioremap.c b/arch/x86/mm/ioremap.c index 016f335bbee..6ba6f889c79 100644 --- a/arch/x86/mm/ioremap.c +++ b/arch/x86/mm/ioremap.c @@ -170,7 +170,7 @@ static void __iomem *__ioremap_caller(resource_size_t phys_addr, phys_addr &= PAGE_MASK; size = PAGE_ALIGN(last_addr+1) - phys_addr; - retval = reserve_memtype(phys_addr, phys_addr + size, + retval = reserve_memtype(phys_addr, (u64)phys_addr + size, prot_val, &new_prot_val); if (retval) { pr_debug("Warning: reserve_memtype returned %d\n", retval); -- GitLab From 024b246ed24492d6c2ee14c34d742b137fce1b94 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Fri, 15 Aug 2008 09:19:40 -0700 Subject: [PATCH 444/750] alpha: move include/asm-alpha to arch/alpha/include/asm Sam Ravnborg did the build-test that the direct header file move works, I'm just committing it. This is a pure move: mkdir arch/alpha/include git mv include/asm-alpha arch/alpha/include/asm with no other changes. Requested-and-tested-by: Sam Ravnborg Cc: Richard Henderson Cc: Ivan Kokshaysky Signed-off-by: Linus Torvalds --- {include/asm-alpha => arch/alpha/include/asm}/8253pit.h | 0 {include/asm-alpha => arch/alpha/include/asm}/Kbuild | 0 {include/asm-alpha => arch/alpha/include/asm}/a.out-core.h | 0 {include/asm-alpha => arch/alpha/include/asm}/a.out.h | 0 {include/asm-alpha => arch/alpha/include/asm}/agp.h | 0 {include/asm-alpha => arch/alpha/include/asm}/agp_backend.h | 0 {include/asm-alpha => arch/alpha/include/asm}/atomic.h | 0 {include/asm-alpha => arch/alpha/include/asm}/auxvec.h | 0 {include/asm-alpha => arch/alpha/include/asm}/barrier.h | 0 {include/asm-alpha => arch/alpha/include/asm}/bitops.h | 0 {include/asm-alpha => arch/alpha/include/asm}/bug.h | 0 {include/asm-alpha => arch/alpha/include/asm}/bugs.h | 0 {include/asm-alpha => arch/alpha/include/asm}/byteorder.h | 0 {include/asm-alpha => arch/alpha/include/asm}/cache.h | 0 {include/asm-alpha => arch/alpha/include/asm}/cacheflush.h | 0 {include/asm-alpha => arch/alpha/include/asm}/checksum.h | 0 {include/asm-alpha => arch/alpha/include/asm}/compiler.h | 0 {include/asm-alpha => arch/alpha/include/asm}/console.h | 0 {include/asm-alpha => arch/alpha/include/asm}/core_apecs.h | 0 {include/asm-alpha => arch/alpha/include/asm}/core_cia.h | 0 {include/asm-alpha => arch/alpha/include/asm}/core_irongate.h | 0 {include/asm-alpha => arch/alpha/include/asm}/core_lca.h | 0 {include/asm-alpha => arch/alpha/include/asm}/core_marvel.h | 0 {include/asm-alpha => arch/alpha/include/asm}/core_mcpcia.h | 0 {include/asm-alpha => arch/alpha/include/asm}/core_polaris.h | 0 {include/asm-alpha => arch/alpha/include/asm}/core_t2.h | 0 {include/asm-alpha => arch/alpha/include/asm}/core_titan.h | 0 {include/asm-alpha => arch/alpha/include/asm}/core_tsunami.h | 0 {include/asm-alpha => arch/alpha/include/asm}/core_wildfire.h | 0 {include/asm-alpha => arch/alpha/include/asm}/cputime.h | 0 {include/asm-alpha => arch/alpha/include/asm}/current.h | 0 {include/asm-alpha => arch/alpha/include/asm}/delay.h | 0 {include/asm-alpha => arch/alpha/include/asm}/device.h | 0 {include/asm-alpha => arch/alpha/include/asm}/div64.h | 0 {include/asm-alpha => arch/alpha/include/asm}/dma-mapping.h | 0 {include/asm-alpha => arch/alpha/include/asm}/dma.h | 0 {include/asm-alpha => arch/alpha/include/asm}/elf.h | 0 {include/asm-alpha => arch/alpha/include/asm}/emergency-restart.h | 0 {include/asm-alpha => arch/alpha/include/asm}/err_common.h | 0 {include/asm-alpha => arch/alpha/include/asm}/err_ev6.h | 0 {include/asm-alpha => arch/alpha/include/asm}/err_ev7.h | 0 {include/asm-alpha => arch/alpha/include/asm}/errno.h | 0 {include/asm-alpha => arch/alpha/include/asm}/fb.h | 0 {include/asm-alpha => arch/alpha/include/asm}/fcntl.h | 0 {include/asm-alpha => arch/alpha/include/asm}/floppy.h | 0 {include/asm-alpha => arch/alpha/include/asm}/fpu.h | 0 {include/asm-alpha => arch/alpha/include/asm}/futex.h | 0 {include/asm-alpha => arch/alpha/include/asm}/gct.h | 0 {include/asm-alpha => arch/alpha/include/asm}/gentrap.h | 0 {include/asm-alpha => arch/alpha/include/asm}/hardirq.h | 0 {include/asm-alpha => arch/alpha/include/asm}/hw_irq.h | 0 {include/asm-alpha => arch/alpha/include/asm}/hwrpb.h | 0 {include/asm-alpha => arch/alpha/include/asm}/io.h | 0 {include/asm-alpha => arch/alpha/include/asm}/io_trivial.h | 0 {include/asm-alpha => arch/alpha/include/asm}/ioctl.h | 0 {include/asm-alpha => arch/alpha/include/asm}/ioctls.h | 0 {include/asm-alpha => arch/alpha/include/asm}/ipcbuf.h | 0 {include/asm-alpha => arch/alpha/include/asm}/irq.h | 0 {include/asm-alpha => arch/alpha/include/asm}/irq_regs.h | 0 {include/asm-alpha => arch/alpha/include/asm}/jensen.h | 0 {include/asm-alpha => arch/alpha/include/asm}/kdebug.h | 0 {include/asm-alpha => arch/alpha/include/asm}/kmap_types.h | 0 {include/asm-alpha => arch/alpha/include/asm}/linkage.h | 0 {include/asm-alpha => arch/alpha/include/asm}/local.h | 0 {include/asm-alpha => arch/alpha/include/asm}/machvec.h | 0 {include/asm-alpha => arch/alpha/include/asm}/mc146818rtc.h | 0 {include/asm-alpha => arch/alpha/include/asm}/md.h | 0 {include/asm-alpha => arch/alpha/include/asm}/mman.h | 0 {include/asm-alpha => arch/alpha/include/asm}/mmu.h | 0 {include/asm-alpha => arch/alpha/include/asm}/mmu_context.h | 0 {include/asm-alpha => arch/alpha/include/asm}/mmzone.h | 0 {include/asm-alpha => arch/alpha/include/asm}/module.h | 0 {include/asm-alpha => arch/alpha/include/asm}/msgbuf.h | 0 {include/asm-alpha => arch/alpha/include/asm}/mutex.h | 0 {include/asm-alpha => arch/alpha/include/asm}/page.h | 0 {include/asm-alpha => arch/alpha/include/asm}/pal.h | 0 {include/asm-alpha => arch/alpha/include/asm}/param.h | 0 {include/asm-alpha => arch/alpha/include/asm}/parport.h | 0 {include/asm-alpha => arch/alpha/include/asm}/pci.h | 0 {include/asm-alpha => arch/alpha/include/asm}/percpu.h | 0 {include/asm-alpha => arch/alpha/include/asm}/pgalloc.h | 0 {include/asm-alpha => arch/alpha/include/asm}/pgtable.h | 0 {include/asm-alpha => arch/alpha/include/asm}/poll.h | 0 {include/asm-alpha => arch/alpha/include/asm}/posix_types.h | 0 {include/asm-alpha => arch/alpha/include/asm}/processor.h | 0 {include/asm-alpha => arch/alpha/include/asm}/ptrace.h | 0 {include/asm-alpha => arch/alpha/include/asm}/reg.h | 0 {include/asm-alpha => arch/alpha/include/asm}/regdef.h | 0 {include/asm-alpha => arch/alpha/include/asm}/resource.h | 0 {include/asm-alpha => arch/alpha/include/asm}/rtc.h | 0 {include/asm-alpha => arch/alpha/include/asm}/rwsem.h | 0 {include/asm-alpha => arch/alpha/include/asm}/scatterlist.h | 0 {include/asm-alpha => arch/alpha/include/asm}/sections.h | 0 {include/asm-alpha => arch/alpha/include/asm}/segment.h | 0 {include/asm-alpha => arch/alpha/include/asm}/sembuf.h | 0 {include/asm-alpha => arch/alpha/include/asm}/serial.h | 0 {include/asm-alpha => arch/alpha/include/asm}/setup.h | 0 {include/asm-alpha => arch/alpha/include/asm}/sfp-machine.h | 0 {include/asm-alpha => arch/alpha/include/asm}/shmbuf.h | 0 {include/asm-alpha => arch/alpha/include/asm}/shmparam.h | 0 {include/asm-alpha => arch/alpha/include/asm}/sigcontext.h | 0 {include/asm-alpha => arch/alpha/include/asm}/siginfo.h | 0 {include/asm-alpha => arch/alpha/include/asm}/signal.h | 0 {include/asm-alpha => arch/alpha/include/asm}/smp.h | 0 {include/asm-alpha => arch/alpha/include/asm}/socket.h | 0 {include/asm-alpha => arch/alpha/include/asm}/sockios.h | 0 {include/asm-alpha => arch/alpha/include/asm}/spinlock.h | 0 {include/asm-alpha => arch/alpha/include/asm}/spinlock_types.h | 0 {include/asm-alpha => arch/alpha/include/asm}/stat.h | 0 {include/asm-alpha => arch/alpha/include/asm}/statfs.h | 0 {include/asm-alpha => arch/alpha/include/asm}/string.h | 0 {include/asm-alpha => arch/alpha/include/asm}/suspend.h | 0 {include/asm-alpha => arch/alpha/include/asm}/sysinfo.h | 0 {include/asm-alpha => arch/alpha/include/asm}/system.h | 0 {include/asm-alpha => arch/alpha/include/asm}/termbits.h | 0 {include/asm-alpha => arch/alpha/include/asm}/termios.h | 0 {include/asm-alpha => arch/alpha/include/asm}/thread_info.h | 0 {include/asm-alpha => arch/alpha/include/asm}/timex.h | 0 {include/asm-alpha => arch/alpha/include/asm}/tlb.h | 0 {include/asm-alpha => arch/alpha/include/asm}/tlbflush.h | 0 {include/asm-alpha => arch/alpha/include/asm}/topology.h | 0 {include/asm-alpha => arch/alpha/include/asm}/types.h | 0 {include/asm-alpha => arch/alpha/include/asm}/uaccess.h | 0 {include/asm-alpha => arch/alpha/include/asm}/ucontext.h | 0 {include/asm-alpha => arch/alpha/include/asm}/unaligned.h | 0 {include/asm-alpha => arch/alpha/include/asm}/unistd.h | 0 {include/asm-alpha => arch/alpha/include/asm}/user.h | 0 {include/asm-alpha => arch/alpha/include/asm}/vga.h | 0 {include/asm-alpha => arch/alpha/include/asm}/xor.h | 0 129 files changed, 0 insertions(+), 0 deletions(-) rename {include/asm-alpha => arch/alpha/include/asm}/8253pit.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/Kbuild (100%) rename {include/asm-alpha => arch/alpha/include/asm}/a.out-core.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/a.out.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/agp.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/agp_backend.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/atomic.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/auxvec.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/barrier.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/bitops.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/bug.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/bugs.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/byteorder.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/cache.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/cacheflush.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/checksum.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/compiler.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/console.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/core_apecs.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/core_cia.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/core_irongate.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/core_lca.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/core_marvel.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/core_mcpcia.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/core_polaris.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/core_t2.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/core_titan.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/core_tsunami.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/core_wildfire.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/cputime.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/current.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/delay.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/device.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/div64.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/dma-mapping.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/dma.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/elf.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/emergency-restart.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/err_common.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/err_ev6.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/err_ev7.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/errno.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/fb.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/fcntl.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/floppy.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/fpu.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/futex.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/gct.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/gentrap.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/hardirq.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/hw_irq.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/hwrpb.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/io.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/io_trivial.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/ioctl.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/ioctls.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/ipcbuf.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/irq.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/irq_regs.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/jensen.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/kdebug.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/kmap_types.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/linkage.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/local.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/machvec.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/mc146818rtc.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/md.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/mman.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/mmu.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/mmu_context.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/mmzone.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/module.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/msgbuf.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/mutex.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/page.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/pal.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/param.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/parport.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/pci.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/percpu.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/pgalloc.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/pgtable.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/poll.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/posix_types.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/processor.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/ptrace.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/reg.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/regdef.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/resource.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/rtc.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/rwsem.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/scatterlist.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/sections.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/segment.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/sembuf.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/serial.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/setup.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/sfp-machine.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/shmbuf.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/shmparam.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/sigcontext.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/siginfo.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/signal.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/smp.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/socket.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/sockios.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/spinlock.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/spinlock_types.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/stat.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/statfs.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/string.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/suspend.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/sysinfo.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/system.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/termbits.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/termios.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/thread_info.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/timex.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/tlb.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/tlbflush.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/topology.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/types.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/uaccess.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/ucontext.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/unaligned.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/unistd.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/user.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/vga.h (100%) rename {include/asm-alpha => arch/alpha/include/asm}/xor.h (100%) diff --git a/include/asm-alpha/8253pit.h b/arch/alpha/include/asm/8253pit.h similarity index 100% rename from include/asm-alpha/8253pit.h rename to arch/alpha/include/asm/8253pit.h diff --git a/include/asm-alpha/Kbuild b/arch/alpha/include/asm/Kbuild similarity index 100% rename from include/asm-alpha/Kbuild rename to arch/alpha/include/asm/Kbuild diff --git a/include/asm-alpha/a.out-core.h b/arch/alpha/include/asm/a.out-core.h similarity index 100% rename from include/asm-alpha/a.out-core.h rename to arch/alpha/include/asm/a.out-core.h diff --git a/include/asm-alpha/a.out.h b/arch/alpha/include/asm/a.out.h similarity index 100% rename from include/asm-alpha/a.out.h rename to arch/alpha/include/asm/a.out.h diff --git a/include/asm-alpha/agp.h b/arch/alpha/include/asm/agp.h similarity index 100% rename from include/asm-alpha/agp.h rename to arch/alpha/include/asm/agp.h diff --git a/include/asm-alpha/agp_backend.h b/arch/alpha/include/asm/agp_backend.h similarity index 100% rename from include/asm-alpha/agp_backend.h rename to arch/alpha/include/asm/agp_backend.h diff --git a/include/asm-alpha/atomic.h b/arch/alpha/include/asm/atomic.h similarity index 100% rename from include/asm-alpha/atomic.h rename to arch/alpha/include/asm/atomic.h diff --git a/include/asm-alpha/auxvec.h b/arch/alpha/include/asm/auxvec.h similarity index 100% rename from include/asm-alpha/auxvec.h rename to arch/alpha/include/asm/auxvec.h diff --git a/include/asm-alpha/barrier.h b/arch/alpha/include/asm/barrier.h similarity index 100% rename from include/asm-alpha/barrier.h rename to arch/alpha/include/asm/barrier.h diff --git a/include/asm-alpha/bitops.h b/arch/alpha/include/asm/bitops.h similarity index 100% rename from include/asm-alpha/bitops.h rename to arch/alpha/include/asm/bitops.h diff --git a/include/asm-alpha/bug.h b/arch/alpha/include/asm/bug.h similarity index 100% rename from include/asm-alpha/bug.h rename to arch/alpha/include/asm/bug.h diff --git a/include/asm-alpha/bugs.h b/arch/alpha/include/asm/bugs.h similarity index 100% rename from include/asm-alpha/bugs.h rename to arch/alpha/include/asm/bugs.h diff --git a/include/asm-alpha/byteorder.h b/arch/alpha/include/asm/byteorder.h similarity index 100% rename from include/asm-alpha/byteorder.h rename to arch/alpha/include/asm/byteorder.h diff --git a/include/asm-alpha/cache.h b/arch/alpha/include/asm/cache.h similarity index 100% rename from include/asm-alpha/cache.h rename to arch/alpha/include/asm/cache.h diff --git a/include/asm-alpha/cacheflush.h b/arch/alpha/include/asm/cacheflush.h similarity index 100% rename from include/asm-alpha/cacheflush.h rename to arch/alpha/include/asm/cacheflush.h diff --git a/include/asm-alpha/checksum.h b/arch/alpha/include/asm/checksum.h similarity index 100% rename from include/asm-alpha/checksum.h rename to arch/alpha/include/asm/checksum.h diff --git a/include/asm-alpha/compiler.h b/arch/alpha/include/asm/compiler.h similarity index 100% rename from include/asm-alpha/compiler.h rename to arch/alpha/include/asm/compiler.h diff --git a/include/asm-alpha/console.h b/arch/alpha/include/asm/console.h similarity index 100% rename from include/asm-alpha/console.h rename to arch/alpha/include/asm/console.h diff --git a/include/asm-alpha/core_apecs.h b/arch/alpha/include/asm/core_apecs.h similarity index 100% rename from include/asm-alpha/core_apecs.h rename to arch/alpha/include/asm/core_apecs.h diff --git a/include/asm-alpha/core_cia.h b/arch/alpha/include/asm/core_cia.h similarity index 100% rename from include/asm-alpha/core_cia.h rename to arch/alpha/include/asm/core_cia.h diff --git a/include/asm-alpha/core_irongate.h b/arch/alpha/include/asm/core_irongate.h similarity index 100% rename from include/asm-alpha/core_irongate.h rename to arch/alpha/include/asm/core_irongate.h diff --git a/include/asm-alpha/core_lca.h b/arch/alpha/include/asm/core_lca.h similarity index 100% rename from include/asm-alpha/core_lca.h rename to arch/alpha/include/asm/core_lca.h diff --git a/include/asm-alpha/core_marvel.h b/arch/alpha/include/asm/core_marvel.h similarity index 100% rename from include/asm-alpha/core_marvel.h rename to arch/alpha/include/asm/core_marvel.h diff --git a/include/asm-alpha/core_mcpcia.h b/arch/alpha/include/asm/core_mcpcia.h similarity index 100% rename from include/asm-alpha/core_mcpcia.h rename to arch/alpha/include/asm/core_mcpcia.h diff --git a/include/asm-alpha/core_polaris.h b/arch/alpha/include/asm/core_polaris.h similarity index 100% rename from include/asm-alpha/core_polaris.h rename to arch/alpha/include/asm/core_polaris.h diff --git a/include/asm-alpha/core_t2.h b/arch/alpha/include/asm/core_t2.h similarity index 100% rename from include/asm-alpha/core_t2.h rename to arch/alpha/include/asm/core_t2.h diff --git a/include/asm-alpha/core_titan.h b/arch/alpha/include/asm/core_titan.h similarity index 100% rename from include/asm-alpha/core_titan.h rename to arch/alpha/include/asm/core_titan.h diff --git a/include/asm-alpha/core_tsunami.h b/arch/alpha/include/asm/core_tsunami.h similarity index 100% rename from include/asm-alpha/core_tsunami.h rename to arch/alpha/include/asm/core_tsunami.h diff --git a/include/asm-alpha/core_wildfire.h b/arch/alpha/include/asm/core_wildfire.h similarity index 100% rename from include/asm-alpha/core_wildfire.h rename to arch/alpha/include/asm/core_wildfire.h diff --git a/include/asm-alpha/cputime.h b/arch/alpha/include/asm/cputime.h similarity index 100% rename from include/asm-alpha/cputime.h rename to arch/alpha/include/asm/cputime.h diff --git a/include/asm-alpha/current.h b/arch/alpha/include/asm/current.h similarity index 100% rename from include/asm-alpha/current.h rename to arch/alpha/include/asm/current.h diff --git a/include/asm-alpha/delay.h b/arch/alpha/include/asm/delay.h similarity index 100% rename from include/asm-alpha/delay.h rename to arch/alpha/include/asm/delay.h diff --git a/include/asm-alpha/device.h b/arch/alpha/include/asm/device.h similarity index 100% rename from include/asm-alpha/device.h rename to arch/alpha/include/asm/device.h diff --git a/include/asm-alpha/div64.h b/arch/alpha/include/asm/div64.h similarity index 100% rename from include/asm-alpha/div64.h rename to arch/alpha/include/asm/div64.h diff --git a/include/asm-alpha/dma-mapping.h b/arch/alpha/include/asm/dma-mapping.h similarity index 100% rename from include/asm-alpha/dma-mapping.h rename to arch/alpha/include/asm/dma-mapping.h diff --git a/include/asm-alpha/dma.h b/arch/alpha/include/asm/dma.h similarity index 100% rename from include/asm-alpha/dma.h rename to arch/alpha/include/asm/dma.h diff --git a/include/asm-alpha/elf.h b/arch/alpha/include/asm/elf.h similarity index 100% rename from include/asm-alpha/elf.h rename to arch/alpha/include/asm/elf.h diff --git a/include/asm-alpha/emergency-restart.h b/arch/alpha/include/asm/emergency-restart.h similarity index 100% rename from include/asm-alpha/emergency-restart.h rename to arch/alpha/include/asm/emergency-restart.h diff --git a/include/asm-alpha/err_common.h b/arch/alpha/include/asm/err_common.h similarity index 100% rename from include/asm-alpha/err_common.h rename to arch/alpha/include/asm/err_common.h diff --git a/include/asm-alpha/err_ev6.h b/arch/alpha/include/asm/err_ev6.h similarity index 100% rename from include/asm-alpha/err_ev6.h rename to arch/alpha/include/asm/err_ev6.h diff --git a/include/asm-alpha/err_ev7.h b/arch/alpha/include/asm/err_ev7.h similarity index 100% rename from include/asm-alpha/err_ev7.h rename to arch/alpha/include/asm/err_ev7.h diff --git a/include/asm-alpha/errno.h b/arch/alpha/include/asm/errno.h similarity index 100% rename from include/asm-alpha/errno.h rename to arch/alpha/include/asm/errno.h diff --git a/include/asm-alpha/fb.h b/arch/alpha/include/asm/fb.h similarity index 100% rename from include/asm-alpha/fb.h rename to arch/alpha/include/asm/fb.h diff --git a/include/asm-alpha/fcntl.h b/arch/alpha/include/asm/fcntl.h similarity index 100% rename from include/asm-alpha/fcntl.h rename to arch/alpha/include/asm/fcntl.h diff --git a/include/asm-alpha/floppy.h b/arch/alpha/include/asm/floppy.h similarity index 100% rename from include/asm-alpha/floppy.h rename to arch/alpha/include/asm/floppy.h diff --git a/include/asm-alpha/fpu.h b/arch/alpha/include/asm/fpu.h similarity index 100% rename from include/asm-alpha/fpu.h rename to arch/alpha/include/asm/fpu.h diff --git a/include/asm-alpha/futex.h b/arch/alpha/include/asm/futex.h similarity index 100% rename from include/asm-alpha/futex.h rename to arch/alpha/include/asm/futex.h diff --git a/include/asm-alpha/gct.h b/arch/alpha/include/asm/gct.h similarity index 100% rename from include/asm-alpha/gct.h rename to arch/alpha/include/asm/gct.h diff --git a/include/asm-alpha/gentrap.h b/arch/alpha/include/asm/gentrap.h similarity index 100% rename from include/asm-alpha/gentrap.h rename to arch/alpha/include/asm/gentrap.h diff --git a/include/asm-alpha/hardirq.h b/arch/alpha/include/asm/hardirq.h similarity index 100% rename from include/asm-alpha/hardirq.h rename to arch/alpha/include/asm/hardirq.h diff --git a/include/asm-alpha/hw_irq.h b/arch/alpha/include/asm/hw_irq.h similarity index 100% rename from include/asm-alpha/hw_irq.h rename to arch/alpha/include/asm/hw_irq.h diff --git a/include/asm-alpha/hwrpb.h b/arch/alpha/include/asm/hwrpb.h similarity index 100% rename from include/asm-alpha/hwrpb.h rename to arch/alpha/include/asm/hwrpb.h diff --git a/include/asm-alpha/io.h b/arch/alpha/include/asm/io.h similarity index 100% rename from include/asm-alpha/io.h rename to arch/alpha/include/asm/io.h diff --git a/include/asm-alpha/io_trivial.h b/arch/alpha/include/asm/io_trivial.h similarity index 100% rename from include/asm-alpha/io_trivial.h rename to arch/alpha/include/asm/io_trivial.h diff --git a/include/asm-alpha/ioctl.h b/arch/alpha/include/asm/ioctl.h similarity index 100% rename from include/asm-alpha/ioctl.h rename to arch/alpha/include/asm/ioctl.h diff --git a/include/asm-alpha/ioctls.h b/arch/alpha/include/asm/ioctls.h similarity index 100% rename from include/asm-alpha/ioctls.h rename to arch/alpha/include/asm/ioctls.h diff --git a/include/asm-alpha/ipcbuf.h b/arch/alpha/include/asm/ipcbuf.h similarity index 100% rename from include/asm-alpha/ipcbuf.h rename to arch/alpha/include/asm/ipcbuf.h diff --git a/include/asm-alpha/irq.h b/arch/alpha/include/asm/irq.h similarity index 100% rename from include/asm-alpha/irq.h rename to arch/alpha/include/asm/irq.h diff --git a/include/asm-alpha/irq_regs.h b/arch/alpha/include/asm/irq_regs.h similarity index 100% rename from include/asm-alpha/irq_regs.h rename to arch/alpha/include/asm/irq_regs.h diff --git a/include/asm-alpha/jensen.h b/arch/alpha/include/asm/jensen.h similarity index 100% rename from include/asm-alpha/jensen.h rename to arch/alpha/include/asm/jensen.h diff --git a/include/asm-alpha/kdebug.h b/arch/alpha/include/asm/kdebug.h similarity index 100% rename from include/asm-alpha/kdebug.h rename to arch/alpha/include/asm/kdebug.h diff --git a/include/asm-alpha/kmap_types.h b/arch/alpha/include/asm/kmap_types.h similarity index 100% rename from include/asm-alpha/kmap_types.h rename to arch/alpha/include/asm/kmap_types.h diff --git a/include/asm-alpha/linkage.h b/arch/alpha/include/asm/linkage.h similarity index 100% rename from include/asm-alpha/linkage.h rename to arch/alpha/include/asm/linkage.h diff --git a/include/asm-alpha/local.h b/arch/alpha/include/asm/local.h similarity index 100% rename from include/asm-alpha/local.h rename to arch/alpha/include/asm/local.h diff --git a/include/asm-alpha/machvec.h b/arch/alpha/include/asm/machvec.h similarity index 100% rename from include/asm-alpha/machvec.h rename to arch/alpha/include/asm/machvec.h diff --git a/include/asm-alpha/mc146818rtc.h b/arch/alpha/include/asm/mc146818rtc.h similarity index 100% rename from include/asm-alpha/mc146818rtc.h rename to arch/alpha/include/asm/mc146818rtc.h diff --git a/include/asm-alpha/md.h b/arch/alpha/include/asm/md.h similarity index 100% rename from include/asm-alpha/md.h rename to arch/alpha/include/asm/md.h diff --git a/include/asm-alpha/mman.h b/arch/alpha/include/asm/mman.h similarity index 100% rename from include/asm-alpha/mman.h rename to arch/alpha/include/asm/mman.h diff --git a/include/asm-alpha/mmu.h b/arch/alpha/include/asm/mmu.h similarity index 100% rename from include/asm-alpha/mmu.h rename to arch/alpha/include/asm/mmu.h diff --git a/include/asm-alpha/mmu_context.h b/arch/alpha/include/asm/mmu_context.h similarity index 100% rename from include/asm-alpha/mmu_context.h rename to arch/alpha/include/asm/mmu_context.h diff --git a/include/asm-alpha/mmzone.h b/arch/alpha/include/asm/mmzone.h similarity index 100% rename from include/asm-alpha/mmzone.h rename to arch/alpha/include/asm/mmzone.h diff --git a/include/asm-alpha/module.h b/arch/alpha/include/asm/module.h similarity index 100% rename from include/asm-alpha/module.h rename to arch/alpha/include/asm/module.h diff --git a/include/asm-alpha/msgbuf.h b/arch/alpha/include/asm/msgbuf.h similarity index 100% rename from include/asm-alpha/msgbuf.h rename to arch/alpha/include/asm/msgbuf.h diff --git a/include/asm-alpha/mutex.h b/arch/alpha/include/asm/mutex.h similarity index 100% rename from include/asm-alpha/mutex.h rename to arch/alpha/include/asm/mutex.h diff --git a/include/asm-alpha/page.h b/arch/alpha/include/asm/page.h similarity index 100% rename from include/asm-alpha/page.h rename to arch/alpha/include/asm/page.h diff --git a/include/asm-alpha/pal.h b/arch/alpha/include/asm/pal.h similarity index 100% rename from include/asm-alpha/pal.h rename to arch/alpha/include/asm/pal.h diff --git a/include/asm-alpha/param.h b/arch/alpha/include/asm/param.h similarity index 100% rename from include/asm-alpha/param.h rename to arch/alpha/include/asm/param.h diff --git a/include/asm-alpha/parport.h b/arch/alpha/include/asm/parport.h similarity index 100% rename from include/asm-alpha/parport.h rename to arch/alpha/include/asm/parport.h diff --git a/include/asm-alpha/pci.h b/arch/alpha/include/asm/pci.h similarity index 100% rename from include/asm-alpha/pci.h rename to arch/alpha/include/asm/pci.h diff --git a/include/asm-alpha/percpu.h b/arch/alpha/include/asm/percpu.h similarity index 100% rename from include/asm-alpha/percpu.h rename to arch/alpha/include/asm/percpu.h diff --git a/include/asm-alpha/pgalloc.h b/arch/alpha/include/asm/pgalloc.h similarity index 100% rename from include/asm-alpha/pgalloc.h rename to arch/alpha/include/asm/pgalloc.h diff --git a/include/asm-alpha/pgtable.h b/arch/alpha/include/asm/pgtable.h similarity index 100% rename from include/asm-alpha/pgtable.h rename to arch/alpha/include/asm/pgtable.h diff --git a/include/asm-alpha/poll.h b/arch/alpha/include/asm/poll.h similarity index 100% rename from include/asm-alpha/poll.h rename to arch/alpha/include/asm/poll.h diff --git a/include/asm-alpha/posix_types.h b/arch/alpha/include/asm/posix_types.h similarity index 100% rename from include/asm-alpha/posix_types.h rename to arch/alpha/include/asm/posix_types.h diff --git a/include/asm-alpha/processor.h b/arch/alpha/include/asm/processor.h similarity index 100% rename from include/asm-alpha/processor.h rename to arch/alpha/include/asm/processor.h diff --git a/include/asm-alpha/ptrace.h b/arch/alpha/include/asm/ptrace.h similarity index 100% rename from include/asm-alpha/ptrace.h rename to arch/alpha/include/asm/ptrace.h diff --git a/include/asm-alpha/reg.h b/arch/alpha/include/asm/reg.h similarity index 100% rename from include/asm-alpha/reg.h rename to arch/alpha/include/asm/reg.h diff --git a/include/asm-alpha/regdef.h b/arch/alpha/include/asm/regdef.h similarity index 100% rename from include/asm-alpha/regdef.h rename to arch/alpha/include/asm/regdef.h diff --git a/include/asm-alpha/resource.h b/arch/alpha/include/asm/resource.h similarity index 100% rename from include/asm-alpha/resource.h rename to arch/alpha/include/asm/resource.h diff --git a/include/asm-alpha/rtc.h b/arch/alpha/include/asm/rtc.h similarity index 100% rename from include/asm-alpha/rtc.h rename to arch/alpha/include/asm/rtc.h diff --git a/include/asm-alpha/rwsem.h b/arch/alpha/include/asm/rwsem.h similarity index 100% rename from include/asm-alpha/rwsem.h rename to arch/alpha/include/asm/rwsem.h diff --git a/include/asm-alpha/scatterlist.h b/arch/alpha/include/asm/scatterlist.h similarity index 100% rename from include/asm-alpha/scatterlist.h rename to arch/alpha/include/asm/scatterlist.h diff --git a/include/asm-alpha/sections.h b/arch/alpha/include/asm/sections.h similarity index 100% rename from include/asm-alpha/sections.h rename to arch/alpha/include/asm/sections.h diff --git a/include/asm-alpha/segment.h b/arch/alpha/include/asm/segment.h similarity index 100% rename from include/asm-alpha/segment.h rename to arch/alpha/include/asm/segment.h diff --git a/include/asm-alpha/sembuf.h b/arch/alpha/include/asm/sembuf.h similarity index 100% rename from include/asm-alpha/sembuf.h rename to arch/alpha/include/asm/sembuf.h diff --git a/include/asm-alpha/serial.h b/arch/alpha/include/asm/serial.h similarity index 100% rename from include/asm-alpha/serial.h rename to arch/alpha/include/asm/serial.h diff --git a/include/asm-alpha/setup.h b/arch/alpha/include/asm/setup.h similarity index 100% rename from include/asm-alpha/setup.h rename to arch/alpha/include/asm/setup.h diff --git a/include/asm-alpha/sfp-machine.h b/arch/alpha/include/asm/sfp-machine.h similarity index 100% rename from include/asm-alpha/sfp-machine.h rename to arch/alpha/include/asm/sfp-machine.h diff --git a/include/asm-alpha/shmbuf.h b/arch/alpha/include/asm/shmbuf.h similarity index 100% rename from include/asm-alpha/shmbuf.h rename to arch/alpha/include/asm/shmbuf.h diff --git a/include/asm-alpha/shmparam.h b/arch/alpha/include/asm/shmparam.h similarity index 100% rename from include/asm-alpha/shmparam.h rename to arch/alpha/include/asm/shmparam.h diff --git a/include/asm-alpha/sigcontext.h b/arch/alpha/include/asm/sigcontext.h similarity index 100% rename from include/asm-alpha/sigcontext.h rename to arch/alpha/include/asm/sigcontext.h diff --git a/include/asm-alpha/siginfo.h b/arch/alpha/include/asm/siginfo.h similarity index 100% rename from include/asm-alpha/siginfo.h rename to arch/alpha/include/asm/siginfo.h diff --git a/include/asm-alpha/signal.h b/arch/alpha/include/asm/signal.h similarity index 100% rename from include/asm-alpha/signal.h rename to arch/alpha/include/asm/signal.h diff --git a/include/asm-alpha/smp.h b/arch/alpha/include/asm/smp.h similarity index 100% rename from include/asm-alpha/smp.h rename to arch/alpha/include/asm/smp.h diff --git a/include/asm-alpha/socket.h b/arch/alpha/include/asm/socket.h similarity index 100% rename from include/asm-alpha/socket.h rename to arch/alpha/include/asm/socket.h diff --git a/include/asm-alpha/sockios.h b/arch/alpha/include/asm/sockios.h similarity index 100% rename from include/asm-alpha/sockios.h rename to arch/alpha/include/asm/sockios.h diff --git a/include/asm-alpha/spinlock.h b/arch/alpha/include/asm/spinlock.h similarity index 100% rename from include/asm-alpha/spinlock.h rename to arch/alpha/include/asm/spinlock.h diff --git a/include/asm-alpha/spinlock_types.h b/arch/alpha/include/asm/spinlock_types.h similarity index 100% rename from include/asm-alpha/spinlock_types.h rename to arch/alpha/include/asm/spinlock_types.h diff --git a/include/asm-alpha/stat.h b/arch/alpha/include/asm/stat.h similarity index 100% rename from include/asm-alpha/stat.h rename to arch/alpha/include/asm/stat.h diff --git a/include/asm-alpha/statfs.h b/arch/alpha/include/asm/statfs.h similarity index 100% rename from include/asm-alpha/statfs.h rename to arch/alpha/include/asm/statfs.h diff --git a/include/asm-alpha/string.h b/arch/alpha/include/asm/string.h similarity index 100% rename from include/asm-alpha/string.h rename to arch/alpha/include/asm/string.h diff --git a/include/asm-alpha/suspend.h b/arch/alpha/include/asm/suspend.h similarity index 100% rename from include/asm-alpha/suspend.h rename to arch/alpha/include/asm/suspend.h diff --git a/include/asm-alpha/sysinfo.h b/arch/alpha/include/asm/sysinfo.h similarity index 100% rename from include/asm-alpha/sysinfo.h rename to arch/alpha/include/asm/sysinfo.h diff --git a/include/asm-alpha/system.h b/arch/alpha/include/asm/system.h similarity index 100% rename from include/asm-alpha/system.h rename to arch/alpha/include/asm/system.h diff --git a/include/asm-alpha/termbits.h b/arch/alpha/include/asm/termbits.h similarity index 100% rename from include/asm-alpha/termbits.h rename to arch/alpha/include/asm/termbits.h diff --git a/include/asm-alpha/termios.h b/arch/alpha/include/asm/termios.h similarity index 100% rename from include/asm-alpha/termios.h rename to arch/alpha/include/asm/termios.h diff --git a/include/asm-alpha/thread_info.h b/arch/alpha/include/asm/thread_info.h similarity index 100% rename from include/asm-alpha/thread_info.h rename to arch/alpha/include/asm/thread_info.h diff --git a/include/asm-alpha/timex.h b/arch/alpha/include/asm/timex.h similarity index 100% rename from include/asm-alpha/timex.h rename to arch/alpha/include/asm/timex.h diff --git a/include/asm-alpha/tlb.h b/arch/alpha/include/asm/tlb.h similarity index 100% rename from include/asm-alpha/tlb.h rename to arch/alpha/include/asm/tlb.h diff --git a/include/asm-alpha/tlbflush.h b/arch/alpha/include/asm/tlbflush.h similarity index 100% rename from include/asm-alpha/tlbflush.h rename to arch/alpha/include/asm/tlbflush.h diff --git a/include/asm-alpha/topology.h b/arch/alpha/include/asm/topology.h similarity index 100% rename from include/asm-alpha/topology.h rename to arch/alpha/include/asm/topology.h diff --git a/include/asm-alpha/types.h b/arch/alpha/include/asm/types.h similarity index 100% rename from include/asm-alpha/types.h rename to arch/alpha/include/asm/types.h diff --git a/include/asm-alpha/uaccess.h b/arch/alpha/include/asm/uaccess.h similarity index 100% rename from include/asm-alpha/uaccess.h rename to arch/alpha/include/asm/uaccess.h diff --git a/include/asm-alpha/ucontext.h b/arch/alpha/include/asm/ucontext.h similarity index 100% rename from include/asm-alpha/ucontext.h rename to arch/alpha/include/asm/ucontext.h diff --git a/include/asm-alpha/unaligned.h b/arch/alpha/include/asm/unaligned.h similarity index 100% rename from include/asm-alpha/unaligned.h rename to arch/alpha/include/asm/unaligned.h diff --git a/include/asm-alpha/unistd.h b/arch/alpha/include/asm/unistd.h similarity index 100% rename from include/asm-alpha/unistd.h rename to arch/alpha/include/asm/unistd.h diff --git a/include/asm-alpha/user.h b/arch/alpha/include/asm/user.h similarity index 100% rename from include/asm-alpha/user.h rename to arch/alpha/include/asm/user.h diff --git a/include/asm-alpha/vga.h b/arch/alpha/include/asm/vga.h similarity index 100% rename from include/asm-alpha/vga.h rename to arch/alpha/include/asm/vga.h diff --git a/include/asm-alpha/xor.h b/arch/alpha/include/asm/xor.h similarity index 100% rename from include/asm-alpha/xor.h rename to arch/alpha/include/asm/xor.h -- GitLab From 55cd53404c5cc5fd94708232e3b4aa4a9388917b Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Mon, 4 Aug 2008 08:54:26 +0200 Subject: [PATCH 445/750] sched: scale sysctl_sched_shares_ratelimit with nr_cpus David reported that his Niagra spend a little too much time in tg_shares_up(), which considering he has a large cpu count makes sense. So scale the ratelimit value with the number of cpus like we do for other controls as well. Reported-by: David Miller Signed-off-by: Peter Zijlstra Signed-off-by: Ingo Molnar --- kernel/sched.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/kernel/sched.c b/kernel/sched.c index 8bf8a5528bc..040807196b3 100644 --- a/kernel/sched.c +++ b/kernel/sched.c @@ -808,9 +808,9 @@ const_debug unsigned int sysctl_sched_nr_migrate = 32; /* * ratelimit for updating the group shares. - * default: 0.5ms + * default: 0.25ms */ -const_debug unsigned int sysctl_sched_shares_ratelimit = 500000; +unsigned int sysctl_sched_shares_ratelimit = 250000; /* * period over which we measure -rt task cpu usage in us. @@ -5740,6 +5740,8 @@ static inline void sched_init_granularity(void) sysctl_sched_latency = limit; sysctl_sched_wakeup_granularity *= factor; + + sysctl_sched_shares_ratelimit *= factor; } #ifdef CONFIG_SMP -- GitLab From fc0091b3c86396afc8e6c273aff21671cf882ee1 Mon Sep 17 00:00:00 2001 From: Alex Nixon Date: Fri, 15 Aug 2008 17:21:14 +0100 Subject: [PATCH 446/750] x86: change init_gdt to update the gdt via write_gdt, rather than a direct write. By writing directly, a memory access violation can occur whilst hotplugging a CPU if the entry was previously marked read-only. Signed-off-by: Alex Nixon Cc: Jeremy Fitzhardinge Signed-off-by: Ingo Molnar --- arch/x86/kernel/smpcommon.c | 17 ++++++++++------- 1 file changed, 10 insertions(+), 7 deletions(-) diff --git a/arch/x86/kernel/smpcommon.c b/arch/x86/kernel/smpcommon.c index 99941b37eca..397e309839d 100644 --- a/arch/x86/kernel/smpcommon.c +++ b/arch/x86/kernel/smpcommon.c @@ -8,18 +8,21 @@ DEFINE_PER_CPU(unsigned long, this_cpu_off); EXPORT_PER_CPU_SYMBOL(this_cpu_off); -/* Initialize the CPU's GDT. This is either the boot CPU doing itself - (still using the master per-cpu area), or a CPU doing it for a - secondary which will soon come up. */ +/* + * Initialize the CPU's GDT. This is either the boot CPU doing itself + * (still using the master per-cpu area), or a CPU doing it for a + * secondary which will soon come up. + */ __cpuinit void init_gdt(int cpu) { - struct desc_struct *gdt = get_cpu_gdt_table(cpu); + struct desc_struct gdt; - pack_descriptor(&gdt[GDT_ENTRY_PERCPU], - __per_cpu_offset[cpu], 0xFFFFF, + pack_descriptor(&gdt, __per_cpu_offset[cpu], 0xFFFFF, 0x2 | DESCTYPE_S, 0x8); + gdt.s = 1; - gdt[GDT_ENTRY_PERCPU].s = 1; + write_gdt_entry(get_cpu_gdt_table(cpu), + GDT_ENTRY_PERCPU, &gdt, DESCTYPE_S); per_cpu(this_cpu_off, cpu) = __per_cpu_offset[cpu]; per_cpu(cpu_number, cpu) = cpu; -- GitLab From 8d6ea9674cb12b90c800dc572214bf06f6ce8340 Mon Sep 17 00:00:00 2001 From: Marcin Slusarz Date: Fri, 15 Aug 2008 18:32:24 +0200 Subject: [PATCH 447/750] x86: fix section mismatch warning - spp_getpage() WARNING: vmlinux.o(.text+0x17a3e): Section mismatch in reference from the function set_pte_vaddr_pud() to the function .init.text:spp_getpage() The function set_pte_vaddr_pud() references the function __init spp_getpage(). This is often because set_pte_vaddr_pud lacks a __init annotation or the annotation of spp_getpage is wrong. spp_getpage is called from __init (__init_extra_mapping) and non __init (set_pte_vaddr_pud) functions, so it can't be __init. Unfortunately it calls alloc_bootmem_pages which is __init, but does it only when bootmem allocator is available (after_bootmem == 0). So annotate it accordingly. Signed-off-by: Marcin Slusarz Signed-off-by: Ingo Molnar Cc: H. Peter Anvin --- arch/x86/mm/init_64.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/arch/x86/mm/init_64.c b/arch/x86/mm/init_64.c index b3e6c3075ac..a87ea0e4b3d 100644 --- a/arch/x86/mm/init_64.c +++ b/arch/x86/mm/init_64.c @@ -88,7 +88,11 @@ early_param("gbpages", parse_direct_gbpages_on); int after_bootmem; -static __init void *spp_getpage(void) +/* + * NOTE: This function is marked __ref because it calls __init function + * (alloc_bootmem_pages). It's safe to do it ONLY when after_bootmem == 0. + */ +static __ref void *spp_getpage(void) { void *ptr; -- GitLab From 2fdc86901d2ab30a12402b46238951d2a7891590 Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Wed, 13 Aug 2008 18:02:18 +0200 Subject: [PATCH 448/750] x86: add MAP_STACK mmap flag as per this discussion: http://lkml.org/lkml/2008/8/12/423 Pardo reported that 64-bit threaded apps, if their stacks exceed the combined size of ~4GB, slow down drastically in pthread_create() - because glibc uses MAP_32BIT to allocate the stacks. The use of MAP_32BIT is a legacy hack - to speed up context switching on certain early model 64-bit P4 CPUs. So introduce a new flag to be used by glibc instead, to not constrain 64-bit apps like this. glibc can switch to this new flag straight away - it will be ignored by the kernel. If those old CPUs ever matter to anyone, support for it can be implemented. Signed-off-by: Ingo Molnar Acked-by: Ulrich Drepper --- include/asm-x86/mman.h | 1 + 1 file changed, 1 insertion(+) diff --git a/include/asm-x86/mman.h b/include/asm-x86/mman.h index c1682b542da..90bc4108a4f 100644 --- a/include/asm-x86/mman.h +++ b/include/asm-x86/mman.h @@ -12,6 +12,7 @@ #define MAP_NORESERVE 0x4000 /* don't check for reservations */ #define MAP_POPULATE 0x8000 /* populate (prefault) pagetables */ #define MAP_NONBLOCK 0x10000 /* do not block on IO */ +#define MAP_STACK 0x20000 /* give out an address that is best suited for process/thread stacks */ #define MCL_CURRENT 1 /* lock all current mappings */ #define MCL_FUTURE 2 /* lock all future mappings */ -- GitLab From df60a8441866153d691ae69b77934904c2de5e0d Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Fri, 15 Aug 2008 09:33:05 -0700 Subject: [PATCH 449/750] lockdep: fix build if CONFIG_PROVE_LOCKING not defined If CONFIG_PROVE_LOCKING not defined, then no dependency information is available. Signed-off-by: Stephen Hemminger Signed-off-by: Ingo Molnar --- kernel/lockdep_proc.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/kernel/lockdep_proc.c b/kernel/lockdep_proc.c index fa19aee604c..4b194d34d77 100644 --- a/kernel/lockdep_proc.c +++ b/kernel/lockdep_proc.c @@ -82,7 +82,6 @@ static void print_name(struct seq_file *m, struct lock_class *class) static int l_show(struct seq_file *m, void *v) { - unsigned long nr_forward_deps, nr_backward_deps; struct lock_class *class = v; struct lock_list *entry; char c1, c2, c3, c4; @@ -96,11 +95,10 @@ static int l_show(struct seq_file *m, void *v) #ifdef CONFIG_DEBUG_LOCKDEP seq_printf(m, " OPS:%8ld", class->ops); #endif - nr_forward_deps = lockdep_count_forward_deps(class); - seq_printf(m, " FD:%5ld", nr_forward_deps); - - nr_backward_deps = lockdep_count_backward_deps(class); - seq_printf(m, " BD:%5ld", nr_backward_deps); +#ifdef CONFIG_PROVE_LOCKING + seq_printf(m, " FD:%5ld", lockdep_count_forward_deps(class)); + seq_printf(m, " BD:%5ld", lockdep_count_backward_deps(class)); +#endif get_usage_chars(class, &c1, &c2, &c3, &c4); seq_printf(m, " %c%c%c%c", c1, c2, c3, c4); @@ -325,7 +323,9 @@ static int lockdep_stats_show(struct seq_file *m, void *v) if (class->usage_mask & LOCKF_ENABLED_HARDIRQS_READ) nr_hardirq_read_unsafe++; +#ifdef CONFIG_PROVE_LOCKING sum_forward_deps += lockdep_count_forward_deps(class); +#endif } #ifdef CONFIG_DEBUG_LOCKDEP DEBUG_LOCKS_WARN_ON(debug_atomic_read(&nr_unused_locks) != nr_unused); -- GitLab From 8c9a9dd0fa3a269d380eaae2dc1bee39e865fae1 Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Fri, 15 Aug 2008 10:39:38 +0100 Subject: [PATCH 450/750] tty: remove resize window special case This moves it to being a tty operation. That removes special cases and now also means that resize can be picked up by um and other non vt consoles which may have a resize operation. Signed-off-by: Alan Cox Signed-off-by: Linus Torvalds --- drivers/char/tty_io.c | 72 ++++++++++++++++++--------------- drivers/char/vt.c | 82 ++++++++++++++++++++++++++++---------- drivers/char/vt_ioctl.c | 4 +- include/linux/tty.h | 2 + include/linux/tty_driver.h | 14 +++++++ include/linux/vt_kern.h | 1 - 6 files changed, 121 insertions(+), 54 deletions(-) diff --git a/drivers/char/tty_io.c b/drivers/char/tty_io.c index 0e6866fe0f9..a27160ba21d 100644 --- a/drivers/char/tty_io.c +++ b/drivers/char/tty_io.c @@ -2496,45 +2496,25 @@ static int tiocgwinsz(struct tty_struct *tty, struct winsize __user *arg) } /** - * tiocswinsz - implement window size set ioctl - * @tty; tty - * @arg: user buffer for result + * tty_do_resize - resize event + * @tty: tty being resized + * @real_tty: real tty (if using a pty/tty pair) + * @rows: rows (character) + * @cols: cols (character) * - * Copies the user idea of the window size to the kernel. Traditionally - * this is just advisory information but for the Linux console it - * actually has driver level meaning and triggers a VC resize. - * - * Locking: - * Called function use the console_sem is used to ensure we do - * not try and resize the console twice at once. - * The tty->termios_mutex is used to ensure we don't double - * resize and get confused. Lock order - tty->termios_mutex before - * console sem + * Update the termios variables and send the neccessary signals to + * peform a terminal resize correctly */ -static int tiocswinsz(struct tty_struct *tty, struct tty_struct *real_tty, - struct winsize __user *arg) +int tty_do_resize(struct tty_struct *tty, struct tty_struct *real_tty, + struct winsize *ws) { - struct winsize tmp_ws; struct pid *pgrp, *rpgrp; unsigned long flags; - if (copy_from_user(&tmp_ws, arg, sizeof(*arg))) - return -EFAULT; - mutex_lock(&tty->termios_mutex); - if (!memcmp(&tmp_ws, &tty->winsize, sizeof(*arg))) + if (!memcmp(ws, &tty->winsize, sizeof(*ws))) goto done; - -#ifdef CONFIG_VT - if (tty->driver->type == TTY_DRIVER_TYPE_CONSOLE) { - if (vc_lock_resize(tty->driver_data, tmp_ws.ws_col, - tmp_ws.ws_row)) { - mutex_unlock(&tty->termios_mutex); - return -ENXIO; - } - } -#endif /* Get the PID values and reference them so we can avoid holding the tty ctrl lock while sending signals */ spin_lock_irqsave(&tty->ctrl_lock, flags); @@ -2550,13 +2530,41 @@ static int tiocswinsz(struct tty_struct *tty, struct tty_struct *real_tty, put_pid(pgrp); put_pid(rpgrp); - tty->winsize = tmp_ws; - real_tty->winsize = tmp_ws; + tty->winsize = *ws; + real_tty->winsize = *ws; done: mutex_unlock(&tty->termios_mutex); return 0; } +/** + * tiocswinsz - implement window size set ioctl + * @tty; tty + * @arg: user buffer for result + * + * Copies the user idea of the window size to the kernel. Traditionally + * this is just advisory information but for the Linux console it + * actually has driver level meaning and triggers a VC resize. + * + * Locking: + * Driver dependant. The default do_resize method takes the + * tty termios mutex and ctrl_lock. The console takes its own lock + * then calls into the default method. + */ + +static int tiocswinsz(struct tty_struct *tty, struct tty_struct *real_tty, + struct winsize __user *arg) +{ + struct winsize tmp_ws; + if (copy_from_user(&tmp_ws, arg, sizeof(*arg))) + return -EFAULT; + + if (tty->ops->resize) + return tty->ops->resize(tty, real_tty, &tmp_ws); + else + return tty_do_resize(tty, real_tty, &tmp_ws); +} + /** * tioccons - allow admin to move logical console * @file: the file to become console diff --git a/drivers/char/vt.c b/drivers/char/vt.c index 1bc00c9d860..60359c36091 100644 --- a/drivers/char/vt.c +++ b/drivers/char/vt.c @@ -803,7 +803,25 @@ static inline int resize_screen(struct vc_data *vc, int width, int height, */ #define VC_RESIZE_MAXCOL (32767) #define VC_RESIZE_MAXROW (32767) -int vc_resize(struct vc_data *vc, unsigned int cols, unsigned int lines) + +/** + * vc_do_resize - resizing method for the tty + * @tty: tty being resized + * @real_tty: real tty (different to tty if a pty/tty pair) + * @vc: virtual console private data + * @cols: columns + * @lines: lines + * + * Resize a virtual console, clipping according to the actual constraints. + * If the caller passes a tty structure then update the termios winsize + * information and perform any neccessary signal handling. + * + * Caller must hold the console semaphore. Takes the termios mutex and + * ctrl_lock of the tty IFF a tty is passed. + */ + +static int vc_do_resize(struct tty_struct *tty, struct tty_struct *real_tty, + struct vc_data *vc, unsigned int cols, unsigned int lines) { unsigned long old_origin, new_origin, new_scr_end, rlth, rrem, err = 0; unsigned int old_cols, old_rows, old_row_size, old_screen_size; @@ -907,24 +925,15 @@ int vc_resize(struct vc_data *vc, unsigned int cols, unsigned int lines) gotoxy(vc, vc->vc_x, vc->vc_y); save_cur(vc); - if (vc->vc_tty) { - struct winsize ws, *cws = &vc->vc_tty->winsize; - struct pid *pgrp = NULL; - + if (tty) { + /* Rewrite the requested winsize data with the actual + resulting sizes */ + struct winsize ws; memset(&ws, 0, sizeof(ws)); ws.ws_row = vc->vc_rows; ws.ws_col = vc->vc_cols; ws.ws_ypixel = vc->vc_scan_lines; - - spin_lock_irq(&vc->vc_tty->ctrl_lock); - if ((ws.ws_row != cws->ws_row || ws.ws_col != cws->ws_col)) - pgrp = get_pid(vc->vc_tty->pgrp); - spin_unlock_irq(&vc->vc_tty->ctrl_lock); - if (pgrp) { - kill_pgrp(vc->vc_tty->pgrp, SIGWINCH, 1); - put_pid(pgrp); - } - *cws = ws; + tty_do_resize(tty, real_tty, &ws); } if (CON_IS_VISIBLE(vc)) @@ -932,14 +941,47 @@ int vc_resize(struct vc_data *vc, unsigned int cols, unsigned int lines) return err; } -int vc_lock_resize(struct vc_data *vc, unsigned int cols, unsigned int lines) +/** + * vc_resize - resize a VT + * @vc: virtual console + * @cols: columns + * @rows: rows + * + * Resize a virtual console as seen from the console end of things. We + * use the common vc_do_resize methods to update the structures. The + * caller must hold the console sem to protect console internals and + * vc->vc_tty + */ + +int vc_resize(struct vc_data *vc, unsigned int cols, unsigned int rows) +{ + return vc_do_resize(vc->vc_tty, vc->vc_tty, vc, cols, rows); +} + +/** + * vt_resize - resize a VT + * @tty: tty to resize + * @real_tty: tty if a pty/tty pair + * @ws: winsize attributes + * + * Resize a virtual terminal. This is called by the tty layer as we + * register our own handler for resizing. The mutual helper does all + * the actual work. + * + * Takes the console sem and the called methods then take the tty + * termios_mutex and the tty ctrl_lock in that order. + */ + +int vt_resize(struct tty_struct *tty, struct tty_struct *real_tty, + struct winsize *ws) { - int rc; + struct vc_data *vc = tty->driver_data; + int ret; acquire_console_sem(); - rc = vc_resize(vc, cols, lines); + ret = vc_do_resize(tty, real_tty, vc, ws->ws_col, ws->ws_row); release_console_sem(); - return rc; + return ret; } void vc_deallocate(unsigned int currcons) @@ -2907,6 +2949,7 @@ static const struct tty_operations con_ops = { .start = con_start, .throttle = con_throttle, .unthrottle = con_unthrottle, + .resize = vt_resize, }; int __init vty_init(void) @@ -4061,7 +4104,6 @@ EXPORT_SYMBOL(default_blu); EXPORT_SYMBOL(update_region); EXPORT_SYMBOL(redraw_screen); EXPORT_SYMBOL(vc_resize); -EXPORT_SYMBOL(vc_lock_resize); EXPORT_SYMBOL(fg_console); EXPORT_SYMBOL(console_blank_hook); EXPORT_SYMBOL(console_blanked); diff --git a/drivers/char/vt_ioctl.c b/drivers/char/vt_ioctl.c index 3211afd9d57..c904e9ad4a7 100644 --- a/drivers/char/vt_ioctl.c +++ b/drivers/char/vt_ioctl.c @@ -947,14 +947,16 @@ int vt_ioctl(struct tty_struct *tty, struct file * file, get_user(cc, &vtsizes->v_cols)) ret = -EFAULT; else { + acquire_console_sem(); for (i = 0; i < MAX_NR_CONSOLES; i++) { vc = vc_cons[i].d; if (vc) { vc->vc_resize_user = 1; - vc_lock_resize(vc_cons[i].d, cc, ll); + vc_resize(vc_cons[i].d, cc, ll); } } + release_console_sem(); } break; } diff --git a/include/linux/tty.h b/include/linux/tty.h index e3579cb086e..0cbec74ec08 100644 --- a/include/linux/tty.h +++ b/include/linux/tty.h @@ -331,6 +331,8 @@ extern int tty_write_room(struct tty_struct *tty); extern void tty_driver_flush_buffer(struct tty_struct *tty); extern void tty_throttle(struct tty_struct *tty); extern void tty_unthrottle(struct tty_struct *tty); +extern int tty_do_resize(struct tty_struct *tty, struct tty_struct *real_tty, + struct winsize *ws); extern int is_current_pgrp_orphaned(void); extern struct pid *tty_get_pgrp(struct tty_struct *tty); diff --git a/include/linux/tty_driver.h b/include/linux/tty_driver.h index e1065ac0d92..16d27944c32 100644 --- a/include/linux/tty_driver.h +++ b/include/linux/tty_driver.h @@ -168,6 +168,18 @@ * * Optional: If not provided then the write method is called under * the atomic write lock to keep it serialized with the ldisc. + * + * int (*resize)(struct tty_struct *tty, struct tty_struct *real_tty, + * unsigned int rows, unsigned int cols); + * + * Called when a termios request is issued which changes the + * requested terminal geometry. + * + * Optional: the default action is to update the termios structure + * without error. This is usually the correct behaviour. Drivers should + * not force errors here if they are not resizable objects (eg a serial + * line). See tty_do_resize() if you need to wrap the standard method + * in your own logic - the usual case. */ #include @@ -206,6 +218,8 @@ struct tty_operations { int (*tiocmget)(struct tty_struct *tty, struct file *file); int (*tiocmset)(struct tty_struct *tty, struct file *file, unsigned int set, unsigned int clear); + int (*resize)(struct tty_struct *tty, struct tty_struct *real_tty, + struct winsize *ws); #ifdef CONFIG_CONSOLE_POLL int (*poll_init)(struct tty_driver *driver, int line, char *options); int (*poll_get_char)(struct tty_driver *driver, int line); diff --git a/include/linux/vt_kern.h b/include/linux/vt_kern.h index 1c78d56c57e..1cbd0a7db4e 100644 --- a/include/linux/vt_kern.h +++ b/include/linux/vt_kern.h @@ -35,7 +35,6 @@ extern int fg_console, last_console, want_console; int vc_allocate(unsigned int console); int vc_cons_allocated(unsigned int console); int vc_resize(struct vc_data *vc, unsigned int cols, unsigned int lines); -int vc_lock_resize(struct vc_data *vc, unsigned int cols, unsigned int lines); void vc_deallocate(unsigned int console); void reset_palette(struct vc_data *vc); void do_blank_screen(int entering_gfx); -- GitLab From 7ec01ff950c455aa1f1ccfaf347eb1aa9ec160d5 Mon Sep 17 00:00:00 2001 From: Ralph Campbell Date: Fri, 15 Aug 2008 11:23:47 -0700 Subject: [PATCH 451/750] IB/ipath: Fix lost UD send work request If a UD QP has some work requests queued to be sent by the DMA engine followed by a local loopback work request, we have to wait for the previous work requests to finish or the completion for the local loopback work request would be generated out of order. The problem was that the work request queue pointer was already updated so that the request would not be processed when the DMA queue drained. Signed-off-by: Ralph Campbell Signed-off-by: Roland Dreier --- drivers/infiniband/hw/ipath/ipath_ud.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) diff --git a/drivers/infiniband/hw/ipath/ipath_ud.c b/drivers/infiniband/hw/ipath/ipath_ud.c index 36aa242c487..729446f56aa 100644 --- a/drivers/infiniband/hw/ipath/ipath_ud.c +++ b/drivers/infiniband/hw/ipath/ipath_ud.c @@ -267,6 +267,7 @@ int ipath_make_ud_req(struct ipath_qp *qp) u16 lrh0; u16 lid; int ret = 0; + int next_cur; spin_lock_irqsave(&qp->s_lock, flags); @@ -290,8 +291,9 @@ int ipath_make_ud_req(struct ipath_qp *qp) goto bail; wqe = get_swqe_ptr(qp, qp->s_cur); - if (++qp->s_cur >= qp->s_size) - qp->s_cur = 0; + next_cur = qp->s_cur + 1; + if (next_cur >= qp->s_size) + next_cur = 0; /* Construct the header. */ ah_attr = &to_iah(wqe->wr.wr.ud.ah)->attr; @@ -315,6 +317,7 @@ int ipath_make_ud_req(struct ipath_qp *qp) qp->s_flags |= IPATH_S_WAIT_DMA; goto bail; } + qp->s_cur = next_cur; spin_unlock_irqrestore(&qp->s_lock, flags); ipath_ud_loopback(qp, wqe); spin_lock_irqsave(&qp->s_lock, flags); @@ -323,6 +326,7 @@ int ipath_make_ud_req(struct ipath_qp *qp) } } + qp->s_cur = next_cur; extra_bytes = -wqe->length & 3; nwords = (wqe->length + extra_bytes) >> 2; -- GitLab From 24babadec0209e5f84c067cb89aca6515486d35c Mon Sep 17 00:00:00 2001 From: Dave Olson Date: Fri, 15 Aug 2008 11:25:20 -0700 Subject: [PATCH 452/750] IB/ipath: Fix incorrect check for max physical address in TID The check for max physical address was incorrect, thus limiting the range of allowed physical addresses. Signed-off-by: Dave Olson Signed-off-by: Roland Dreier --- drivers/infiniband/hw/ipath/ipath_iba7220.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/infiniband/hw/ipath/ipath_iba7220.c b/drivers/infiniband/hw/ipath/ipath_iba7220.c index d90f5e9a54f..9839e20119b 100644 --- a/drivers/infiniband/hw/ipath/ipath_iba7220.c +++ b/drivers/infiniband/hw/ipath/ipath_iba7220.c @@ -1720,7 +1720,7 @@ static void ipath_7220_put_tid(struct ipath_devdata *dd, u64 __iomem *tidptr, "not 2KB aligned!\n", pa); return; } - if (pa >= (1UL << IBA7220_TID_SZ_SHIFT)) { + if (chippa >= (1UL << IBA7220_TID_SZ_SHIFT)) { ipath_dev_err(dd, "BUG: Physical page address 0x%lx " "larger than supported\n", pa); -- GitLab From cd98a04a59e2f94fa64d5bf1e26498d27427d5e7 Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Wed, 13 Aug 2008 18:02:18 +0200 Subject: [PATCH 453/750] x86: add MAP_STACK mmap flag as per this discussion: http://lkml.org/lkml/2008/8/12/423 Pardo reported that 64-bit threaded apps, if their stacks exceed the combined size of ~4GB, slow down drastically in pthread_create() - because glibc uses MAP_32BIT to allocate the stacks. The use of MAP_32BIT is a legacy hack - to speed up context switching on certain early model 64-bit P4 CPUs. So introduce a new flag to be used by glibc instead, to not constrain 64-bit apps like this. glibc can switch to this new flag straight away - it will be ignored by the kernel. If those old CPUs ever matter to anyone, support for it can be implemented. Signed-off-by: Ingo Molnar Acked-by: Ulrich Drepper Signed-off-by: Linus Torvalds --- include/asm-x86/mman.h | 1 + 1 file changed, 1 insertion(+) diff --git a/include/asm-x86/mman.h b/include/asm-x86/mman.h index c1682b542da..90bc4108a4f 100644 --- a/include/asm-x86/mman.h +++ b/include/asm-x86/mman.h @@ -12,6 +12,7 @@ #define MAP_NORESERVE 0x4000 /* don't check for reservations */ #define MAP_POPULATE 0x8000 /* populate (prefault) pagetables */ #define MAP_NONBLOCK 0x10000 /* do not block on IO */ +#define MAP_STACK 0x20000 /* give out an address that is best suited for process/thread stacks */ #define MCL_CURRENT 1 /* lock all current mappings */ #define MCL_FUTURE 2 /* lock all future mappings */ -- GitLab From cebd7709d396b59ff53b95fa3c4d9febbd4c010f Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Fri, 15 Aug 2008 10:58:05 +0200 Subject: [PATCH 454/750] hwmon-vid: Fix AMD K8 VID decoding Not all AMD K8 have 6 VID pins, contrary to what was assumed in commit 116d0486bdefc11f71e567cadf0c47f788b4dd06. This commit broke support of older CPU models which have only 5 VID pins: http://bugzilla.kernel.org/show_bug.cgi?id=11329 We need two entries in the hwmon-vid table, one for 5-bit VID models (K8 revision <= E) and one for 6-bit VID models (K8 revision >= F). This fixes bug #11329. Signed-off-by: Jean Delvare Acked-by: Frank Myhr Tested-by: Jean-Luc Coulon Signed-off-by: Linus Torvalds --- drivers/hwmon/hwmon-vid.c | 36 ++++++++++++++++++++++++++++-------- 1 file changed, 28 insertions(+), 8 deletions(-) diff --git a/drivers/hwmon/hwmon-vid.c b/drivers/hwmon/hwmon-vid.c index 7b0a32c4dcf..c54eff92be4 100644 --- a/drivers/hwmon/hwmon-vid.c +++ b/drivers/hwmon/hwmon-vid.c @@ -37,13 +37,21 @@ * For VRD 10.0 and up, "VRD x.y Design Guide", * available at http://developer.intel.com/. * - * AMD NPT 0Fh (Athlon64 & Opteron), AMD Publication 32559, + * AMD Athlon 64 and AMD Opteron Processors, AMD Publication 26094, + * http://www.amd.com/us-en/assets/content_type/white_papers_and_tech_docs/26094.PDF + * Table 74. VID Code Voltages + * This corresponds to an arbitrary VRM code of 24 in the functions below. + * These CPU models (K8 revision <= E) have 5 VID pins. See also: + * Revision Guide for AMD Athlon 64 and AMD Opteron Processors, AMD Publication 25759, + * http://www.amd.com/us-en/assets/content_type/white_papers_and_tech_docs/25759.pdf + * + * AMD NPT Family 0Fh Processors, AMD Publication 32559, * http://www.amd.com/us-en/assets/content_type/white_papers_and_tech_docs/32559.pdf * Table 71. VID Code Voltages - * AMD Opteron processors don't follow the Intel specifications. - * I'm going to "make up" 2.4 as the spec number for the Opterons. - * No good reason just a mnemonic for the 24x Opteron processor - * series. + * This corresponds to an arbitrary VRM code of 25 in the functions below. + * These CPU models (K8 revision >= F) have 6 VID pins. See also: + * Revision Guide for AMD NPT Family 0Fh Processors, AMD Publication 33610, + * http://www.amd.com/us-en/assets/content_type/white_papers_and_tech_docs/33610.pdf * * The 17 specification is in fact Intel Mobile Voltage Positioning - * (IMVP-II). You can find more information in the datasheet of Max1718 @@ -95,7 +103,12 @@ int vid_from_reg(int val, u8 vrm) return 0; return((1600000 - (val - 2) * 6250 + 500) / 1000); - case 24: /* AMD NPT 0Fh (Athlon64 & Opteron) */ + case 24: /* Athlon64 & Opteron */ + val &= 0x1f; + if (val == 0x1f) + return 0; + /* fall through */ + case 25: /* AMD NPT 0Fh */ val &= 0x3f; return (val < 32) ? 1550 - 25 * val : 775 - (25 * (val - 31)) / 2; @@ -157,11 +170,16 @@ struct vrm_model { #ifdef CONFIG_X86 -/* the stepping parameter is highest acceptable stepping for current line */ +/* + * The stepping parameter is highest acceptable stepping for current line. + * The model match must be exact for 4-bit values. For model values 0x10 + * and above (extended model), all models below the parameter will match. + */ static struct vrm_model vrm_models[] = { {X86_VENDOR_AMD, 0x6, ANY, ANY, 90}, /* Athlon Duron etc */ - {X86_VENDOR_AMD, 0xF, ANY, ANY, 24}, /* Athlon 64, Opteron and above VRM 24 */ + {X86_VENDOR_AMD, 0xF, 0x3F, ANY, 24}, /* Athlon 64, Opteron */ + {X86_VENDOR_AMD, 0xF, ANY, ANY, 25}, /* NPT family 0Fh */ {X86_VENDOR_INTEL, 0x6, 0x9, ANY, 13}, /* Pentium M (130 nm) */ {X86_VENDOR_INTEL, 0x6, 0xB, ANY, 85}, /* Tualatin */ {X86_VENDOR_INTEL, 0x6, 0xD, ANY, 13}, /* Pentium M (90 nm) */ @@ -189,6 +207,8 @@ static u8 find_vrm(u8 eff_family, u8 eff_model, u8 eff_stepping, u8 vendor) if (vrm_models[i].vendor==vendor) if ((vrm_models[i].eff_family==eff_family) && ((vrm_models[i].eff_model==eff_model) || + (vrm_models[i].eff_model >= 0x10 && + eff_model <= vrm_models[i].eff_model) || (vrm_models[i].eff_model==ANY)) && (eff_stepping <= vrm_models[i].eff_stepping)) return vrm_models[i].vrm_type; -- GitLab From a2bd92023357e47f22a34d4cb1635453546662bc Mon Sep 17 00:00:00 2001 From: "venkatesh.pallipadi@intel.com" Date: Wed, 30 Jul 2008 19:21:42 -0700 Subject: [PATCH 455/750] cpuidle: Do not use poll_idle unless user asks for it poll_idle was added to CPUIDLE, just as a low latency idle handler, to be used in cases when user desires CPUs not to enter any idle state at all. It was supposed to be a run time idle=poll option to the user. But, it was indeed getting used during normal menu and ladder governor default case, with no special user setting (Reported by Linus Torvalds). Change below ensures that poll_idle will not be used unless user explicitly asks pm_qos infrastructure for zero latency requirement. Signed-off-by: Venkatesh Pallipadi Signed-off-by: Andi Kleen --- drivers/cpuidle/governors/ladder.c | 14 ++++++++++---- drivers/cpuidle/governors/menu.c | 11 +++++++++-- 2 files changed, 19 insertions(+), 6 deletions(-) diff --git a/drivers/cpuidle/governors/ladder.c b/drivers/cpuidle/governors/ladder.c index ba7b9a6b17a..27ab3bfe375 100644 --- a/drivers/cpuidle/governors/ladder.c +++ b/drivers/cpuidle/governors/ladder.c @@ -67,10 +67,17 @@ static int ladder_select_state(struct cpuidle_device *dev) struct ladder_device *ldev = &__get_cpu_var(ladder_devices); struct ladder_device_state *last_state; int last_residency, last_idx = ldev->last_state_idx; + int latency_req = pm_qos_requirement(PM_QOS_CPU_DMA_LATENCY); if (unlikely(!ldev)) return 0; + /* Special case when user has set very strict latency requirement */ + if (unlikely(latency_req == 0)) { + ladder_do_selection(ldev, last_idx, 0); + return 0; + } + last_state = &ldev->states[last_idx]; if (dev->states[last_idx].flags & CPUIDLE_FLAG_TIME_VALID) @@ -81,8 +88,7 @@ static int ladder_select_state(struct cpuidle_device *dev) /* consider promotion */ if (last_idx < dev->state_count - 1 && last_residency > last_state->threshold.promotion_time && - dev->states[last_idx + 1].exit_latency <= - pm_qos_requirement(PM_QOS_CPU_DMA_LATENCY)) { + dev->states[last_idx + 1].exit_latency <= latency_req) { last_state->stats.promotion_count++; last_state->stats.demotion_count = 0; if (last_state->stats.promotion_count >= last_state->threshold.promotion_count) { @@ -92,7 +98,7 @@ static int ladder_select_state(struct cpuidle_device *dev) } /* consider demotion */ - if (last_idx > 0 && + if (last_idx > CPUIDLE_DRIVER_STATE_START && last_residency < last_state->threshold.demotion_time) { last_state->stats.demotion_count++; last_state->stats.promotion_count = 0; @@ -117,7 +123,7 @@ static int ladder_enable_device(struct cpuidle_device *dev) struct ladder_device_state *lstate; struct cpuidle_state *state; - ldev->last_state_idx = 0; + ldev->last_state_idx = CPUIDLE_DRIVER_STATE_START; for (i = 0; i < dev->state_count; i++) { state = &dev->states[i]; diff --git a/drivers/cpuidle/governors/menu.c b/drivers/cpuidle/governors/menu.c index 78d77c5dc35..b8f3e21530b 100644 --- a/drivers/cpuidle/governors/menu.c +++ b/drivers/cpuidle/governors/menu.c @@ -34,21 +34,28 @@ static DEFINE_PER_CPU(struct menu_device, menu_devices); static int menu_select(struct cpuidle_device *dev) { struct menu_device *data = &__get_cpu_var(menu_devices); + int latency_req = pm_qos_requirement(PM_QOS_CPU_DMA_LATENCY); int i; + /* Special case when user has set very strict latency requirement */ + if (unlikely(latency_req == 0)) { + data->last_state_idx = 0; + return 0; + } + /* determine the expected residency time */ data->expected_us = (u32) ktime_to_ns(tick_nohz_get_sleep_length()) / 1000; /* find the deepest idle state that satisfies our constraints */ - for (i = 1; i < dev->state_count; i++) { + for (i = CPUIDLE_DRIVER_STATE_START + 1; i < dev->state_count; i++) { struct cpuidle_state *s = &dev->states[i]; if (s->target_residency > data->expected_us) break; if (s->target_residency > data->predicted_us) break; - if (s->exit_latency > pm_qos_requirement(PM_QOS_CPU_DMA_LATENCY)) + if (s->exit_latency > latency_req) break; } -- GitLab From 320eee776357db52d6fcfb11cff985b1976a4595 Mon Sep 17 00:00:00 2001 From: "venkatesh.pallipadi@intel.com" Date: Wed, 30 Jul 2008 19:21:43 -0700 Subject: [PATCH 456/750] cpuidle: Menu governor fix wrong usage of measured_us There is a bug in menu governor where we have if (data->elapsed_us < data->elapsed_us + measured_us) with measured_us already having elapsed_us added in tickless case here unsigned int measured_us = cpuidle_get_last_residency(dev) + data->elapsed_us; Also, it should be last_residency, not measured_us, that need to be used to do comparing and distinguish between expected & non-expected events. Refactor menu_reflect() to fix these two problems. Signed-off-by: Venkatesh Pallipadi Signed-off-by: Wei Gang Signed-off-by: Andi Kleen --- drivers/cpuidle/governors/menu.c | 31 +++++++++++++++++++------------ 1 file changed, 19 insertions(+), 12 deletions(-) diff --git a/drivers/cpuidle/governors/menu.c b/drivers/cpuidle/governors/menu.c index b8f3e21530b..8d7cf3f3145 100644 --- a/drivers/cpuidle/governors/menu.c +++ b/drivers/cpuidle/governors/menu.c @@ -74,9 +74,9 @@ static void menu_reflect(struct cpuidle_device *dev) { struct menu_device *data = &__get_cpu_var(menu_devices); int last_idx = data->last_state_idx; - unsigned int measured_us = - cpuidle_get_last_residency(dev) + data->elapsed_us; + unsigned int last_idle_us = cpuidle_get_last_residency(dev); struct cpuidle_state *target = &dev->states[last_idx]; + unsigned int measured_us; /* * Ugh, this idle state doesn't support residency measurements, so we @@ -84,20 +84,27 @@ static void menu_reflect(struct cpuidle_device *dev) * for one full standard timer tick. However, be aware that this * could potentially result in a suboptimal state transition. */ - if (!(target->flags & CPUIDLE_FLAG_TIME_VALID)) - measured_us = USEC_PER_SEC / HZ; + if (unlikely(!(target->flags & CPUIDLE_FLAG_TIME_VALID))) + last_idle_us = USEC_PER_SEC / HZ; - /* Predict time remaining until next break event */ - if (measured_us + BREAK_FUZZ < data->expected_us - target->exit_latency) { - data->predicted_us = max(measured_us, data->last_measured_us); + /* + * measured_us and elapsed_us are the cumulative idle time, since the + * last time we were woken out of idle by an interrupt. + */ + if (data->elapsed_us <= data->elapsed_us + last_idle_us) + measured_us = data->elapsed_us + last_idle_us; + else + measured_us = -1; + + /* Predict time until next break event */ + data->predicted_us = max(measured_us, data->last_measured_us); + + if (last_idle_us + BREAK_FUZZ < + data->expected_us - target->exit_latency) { data->last_measured_us = measured_us; data->elapsed_us = 0; } else { - if (data->elapsed_us < data->elapsed_us + measured_us) - data->elapsed_us = measured_us; - else - data->elapsed_us = -1; - data->predicted_us = max(measured_us, data->last_measured_us); + data->elapsed_us = measured_us; } } -- GitLab From 06d9e908b2248f983b186aaf569c58e1430db85d Mon Sep 17 00:00:00 2001 From: "venkatesh.pallipadi@intel.com" Date: Wed, 30 Jul 2008 19:21:44 -0700 Subject: [PATCH 457/750] cpuidle: Make ladder governor honor latency requirements fully ladder governor only honored latency requirement when promoting C-states. Instead. it should check for latency requirement on each idle call, and demote to appropriate C-state when there is a latency requirement change. Signed-off-by: Venkatesh Pallipadi Signed-off-by: Andi Kleen --- drivers/cpuidle/governors/ladder.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/drivers/cpuidle/governors/ladder.c b/drivers/cpuidle/governors/ladder.c index 27ab3bfe375..a4bec3f919a 100644 --- a/drivers/cpuidle/governors/ladder.c +++ b/drivers/cpuidle/governors/ladder.c @@ -98,6 +98,18 @@ static int ladder_select_state(struct cpuidle_device *dev) } /* consider demotion */ + if (last_idx > CPUIDLE_DRIVER_STATE_START && + dev->states[last_idx].exit_latency > latency_req) { + int i; + + for (i = last_idx - 1; i > CPUIDLE_DRIVER_STATE_START; i--) { + if (dev->states[i].exit_latency <= latency_req) + break; + } + ladder_do_selection(ldev, last_idx, i); + return i; + } + if (last_idx > CPUIDLE_DRIVER_STATE_START && last_residency < last_state->threshold.demotion_time) { last_state->stats.demotion_count++; -- GitLab From c6153b5b77650879d78dec76414213c76dd8d574 Mon Sep 17 00:00:00 2001 From: Herbert Xu Date: Fri, 15 Aug 2008 13:44:31 -0700 Subject: [PATCH 458/750] ipv4: Disable route secret interval on zero interval Let me first state that disabling the route cache hash rebuild should not be done without extensive analysis on the risk profile and careful deliberation. However, there are times when this can be done safely or for testing. For example, when you have mechanisms for ensuring that offending parties do not exist in your network. This patch lets the user disable the rebuild if the interval is set to zero. This also incidentally fixes a divide-by-zero error with name-spaces. In addition, this patch makes the effect of an interval change immediate rather than it taking effect at the next rebuild as is currently the case. Signed-off-by: Herbert Xu Signed-off-by: David S. Miller --- net/ipv4/route.c | 76 ++++++++++++++++++++++++++++++++++++++++++++---- 1 file changed, 70 insertions(+), 6 deletions(-) diff --git a/net/ipv4/route.c b/net/ipv4/route.c index 16fc6f454a3..cca921ea855 100644 --- a/net/ipv4/route.c +++ b/net/ipv4/route.c @@ -2914,6 +2914,68 @@ static int ipv4_sysctl_rtcache_flush_strategy(ctl_table *table, return 0; } +static void rt_secret_reschedule(int old) +{ + struct net *net; + int new = ip_rt_secret_interval; + int diff = new - old; + + if (!diff) + return; + + rtnl_lock(); + for_each_net(net) { + int deleted = del_timer_sync(&net->ipv4.rt_secret_timer); + + if (!new) + continue; + + if (deleted) { + long time = net->ipv4.rt_secret_timer.expires - jiffies; + + if (time <= 0 || (time += diff) <= 0) + time = 0; + + net->ipv4.rt_secret_timer.expires = time; + } else + net->ipv4.rt_secret_timer.expires = new; + + net->ipv4.rt_secret_timer.expires += jiffies; + add_timer(&net->ipv4.rt_secret_timer); + } + rtnl_unlock(); +} + +static int ipv4_sysctl_rt_secret_interval(ctl_table *ctl, int write, + struct file *filp, + void __user *buffer, size_t *lenp, + loff_t *ppos) +{ + int old = ip_rt_secret_interval; + int ret = proc_dointvec_jiffies(ctl, write, filp, buffer, lenp, ppos); + + rt_secret_reschedule(old); + + return ret; +} + +static int ipv4_sysctl_rt_secret_interval_strategy(ctl_table *table, + int __user *name, + int nlen, + void __user *oldval, + size_t __user *oldlenp, + void __user *newval, + size_t newlen) +{ + int old = ip_rt_secret_interval; + int ret = sysctl_jiffies(table, name, nlen, oldval, oldlenp, newval, + newlen); + + rt_secret_reschedule(old); + + return ret; +} + static ctl_table ipv4_route_table[] = { { .ctl_name = NET_IPV4_ROUTE_GC_THRESH, @@ -3048,8 +3110,8 @@ static ctl_table ipv4_route_table[] = { .data = &ip_rt_secret_interval, .maxlen = sizeof(int), .mode = 0644, - .proc_handler = &proc_dointvec_jiffies, - .strategy = &sysctl_jiffies, + .proc_handler = &ipv4_sysctl_rt_secret_interval, + .strategy = &ipv4_sysctl_rt_secret_interval_strategy, }, { .ctl_name = 0 } }; @@ -3126,10 +3188,12 @@ static __net_init int rt_secret_timer_init(struct net *net) net->ipv4.rt_secret_timer.data = (unsigned long)net; init_timer_deferrable(&net->ipv4.rt_secret_timer); - net->ipv4.rt_secret_timer.expires = - jiffies + net_random() % ip_rt_secret_interval + - ip_rt_secret_interval; - add_timer(&net->ipv4.rt_secret_timer); + if (ip_rt_secret_interval) { + net->ipv4.rt_secret_timer.expires = + jiffies + net_random() % ip_rt_secret_interval + + ip_rt_secret_interval; + add_timer(&net->ipv4.rt_secret_timer); + } return 0; } -- GitLab From 77b483f132ba25edf4ef455dd87a91ab7bbf4170 Mon Sep 17 00:00:00 2001 From: Matt Carlson Date: Fri, 15 Aug 2008 14:07:24 -0700 Subject: [PATCH 459/750] tg3: Add APE register access locking If the driver resets the chip while the APE is performing a register access, that register access will never complete and the APE will hang indefinitely. To prevent this race condition, the driver must acquire an APE mutex before resetting the chip. The APE will not attempt a register access until it acquires this lock. Signed-off-by: Matt Carlson Signed-off-by: Michael Chan Signed-off-by: David S. Miller --- drivers/net/tg3.c | 6 ++++++ drivers/net/tg3.h | 1 + 2 files changed, 7 insertions(+) diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c index d2439b85a79..e3fd74b871a 100644 --- a/drivers/net/tg3.c +++ b/drivers/net/tg3.c @@ -536,6 +536,7 @@ static int tg3_ape_lock(struct tg3 *tp, int locknum) return 0; switch (locknum) { + case TG3_APE_LOCK_GRC: case TG3_APE_LOCK_MEM: break; default: @@ -573,6 +574,7 @@ static void tg3_ape_unlock(struct tg3 *tp, int locknum) return; switch (locknum) { + case TG3_APE_LOCK_GRC: case TG3_APE_LOCK_MEM: break; default: @@ -5760,6 +5762,8 @@ static int tg3_chip_reset(struct tg3 *tp) tg3_mdio_stop(tp); + tg3_ape_lock(tp, TG3_APE_LOCK_GRC); + /* No matching tg3_nvram_unlock() after this because * chip reset below will undo the nvram lock. */ @@ -5914,6 +5918,8 @@ static int tg3_chip_reset(struct tg3 *tp) tg3_mdio_start(tp); + tg3_ape_unlock(tp, TG3_APE_LOCK_GRC); + err = tg3_poll_fw(tp); if (err) return err; diff --git a/drivers/net/tg3.h b/drivers/net/tg3.h index df07842172b..dd1af508023 100644 --- a/drivers/net/tg3.h +++ b/drivers/net/tg3.h @@ -1889,6 +1889,7 @@ #define APE_EVENT_STATUS_EVENT_PENDING 0x80000000 /* APE convenience enumerations. */ +#define TG3_APE_LOCK_GRC 1 #define TG3_APE_LOCK_MEM 4 #define TG3_EEPROM_SB_F1R2_MBA_OFF 0x10 -- GitLab From 731fd79c133dc04cabee17ecfa7661189a8df5c8 Mon Sep 17 00:00:00 2001 From: Matt Carlson Date: Fri, 15 Aug 2008 14:07:51 -0700 Subject: [PATCH 460/750] tg3: Refine APE status check Recently, more status bits have been added to the APE status register. This patch refines the status register check so that the driver can send more events than it would have otherwise. Signed-off-by: Matt Carlson Signed-off-by: Michael Chan Signed-off-by: David S. Miller --- drivers/net/tg3.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c index e3fd74b871a..13640f1cab3 100644 --- a/drivers/net/tg3.c +++ b/drivers/net/tg3.c @@ -5495,7 +5495,7 @@ static void tg3_ape_send_event(struct tg3 *tp, u32 event) return; apedata = tg3_ape_read32(tp, TG3_APE_FW_STATUS); - if (apedata != APE_FW_STATUS_READY) + if (!(apedata & APE_FW_STATUS_READY)) return; /* Wait for up to 1 millisecond for APE to service previous event. */ -- GitLab From 3bda12589646caa22b2ed4ef7cf82d17ea59d7a6 Mon Sep 17 00:00:00 2001 From: Matt Carlson Date: Fri, 15 Aug 2008 14:08:22 -0700 Subject: [PATCH 461/750] tg3: Preserve register settings for DASH Broadcom's DASH (Desktop and mobile Architecture for System Hardware) implementation requires that the driver preserve particular register settings. If the driver does not preserve them, communication with the DASH firmware will be lost. Signed-off-by: Matt Carlson Signed-off-by: Michael Chan Signed-off-by: David S. Miller --- drivers/net/tg3.c | 26 ++++++++++++++++++++++++-- drivers/net/tg3.h | 2 ++ 2 files changed, 26 insertions(+), 2 deletions(-) diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c index 13640f1cab3..0ebf2ff60c4 100644 --- a/drivers/net/tg3.c +++ b/drivers/net/tg3.c @@ -2126,6 +2126,13 @@ static int tg3_set_power_state(struct tg3 *tp, pci_power_t state) (tp->tg3_flags & TG3_FLAG_WOL_ENABLE)) mac_mode |= MAC_MODE_MAGIC_PKT_ENABLE; + if (tp->tg3_flags3 & TG3_FLG3_ENABLE_APE) { + mac_mode |= tp->mac_mode & + (MAC_MODE_APE_TX_EN | MAC_MODE_APE_RX_EN); + if (mac_mode & MAC_MODE_APE_TX_EN) + mac_mode |= MAC_MODE_TDE_ENABLE; + } + tw32_f(MAC_MODE, mac_mode); udelay(100); @@ -5912,6 +5919,11 @@ static int tg3_chip_reset(struct tg3 *tp) } else if (tp->tg3_flags2 & TG3_FLG2_MII_SERDES) { tp->mac_mode = MAC_MODE_PORT_MODE_GMII; tw32_f(MAC_MODE, tp->mac_mode); + } else if (tp->tg3_flags3 & TG3_FLG3_ENABLE_APE) { + tp->mac_mode &= (MAC_MODE_APE_TX_EN | MAC_MODE_APE_RX_EN); + if (tp->mac_mode & MAC_MODE_APE_TX_EN) + tp->mac_mode |= MAC_MODE_TDE_ENABLE; + tw32_f(MAC_MODE, tp->mac_mode); } else tw32_f(MAC_MODE, 0); udelay(40); @@ -7412,7 +7424,11 @@ static int tg3_reset_hw(struct tg3 *tp, int reset_phy) udelay(10); } - tp->mac_mode = MAC_MODE_TXSTAT_ENABLE | MAC_MODE_RXSTAT_ENABLE | + if (tp->tg3_flags3 & TG3_FLG3_ENABLE_APE) + tp->mac_mode &= MAC_MODE_APE_TX_EN | MAC_MODE_APE_RX_EN; + else + tp->mac_mode = 0; + tp->mac_mode |= MAC_MODE_TXSTAT_ENABLE | MAC_MODE_RXSTAT_ENABLE | MAC_MODE_TDE_ENABLE | MAC_MODE_RDE_ENABLE | MAC_MODE_FHDE_ENABLE; if (!(tp->tg3_flags2 & TG3_FLG2_5705_PLUS) && !(tp->tg3_flags2 & TG3_FLG2_PHY_SERDES) && @@ -12422,6 +12438,13 @@ static int __devinit tg3_get_invariants(struct tg3 *tp) tp->misc_host_ctrl); } + /* Preserve the APE MAC_MODE bits */ + if (tp->tg3_flags3 & TG3_FLG3_ENABLE_APE) + tp->mac_mode = tr32(MAC_MODE) | + MAC_MODE_APE_TX_EN | MAC_MODE_APE_RX_EN; + else + tp->mac_mode = TG3_DEF_MAC_MODE; + /* these are limited to 10/100 only */ if ((GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5703 && (grc_misc_cfg == 0x8000 || grc_misc_cfg == 0x4000)) || @@ -13281,7 +13304,6 @@ static int __devinit tg3_init_one(struct pci_dev *pdev, tp->pdev = pdev; tp->dev = dev; tp->pm_cap = pm_cap; - tp->mac_mode = TG3_DEF_MAC_MODE; tp->rx_mode = TG3_DEF_RX_MODE; tp->tx_mode = TG3_DEF_TX_MODE; diff --git a/drivers/net/tg3.h b/drivers/net/tg3.h index dd1af508023..377234947e4 100644 --- a/drivers/net/tg3.h +++ b/drivers/net/tg3.h @@ -325,6 +325,8 @@ #define MAC_MODE_TDE_ENABLE 0x00200000 #define MAC_MODE_RDE_ENABLE 0x00400000 #define MAC_MODE_FHDE_ENABLE 0x00800000 +#define MAC_MODE_APE_RX_EN 0x08000000 +#define MAC_MODE_APE_TX_EN 0x10000000 #define MAC_STATUS 0x00000404 #define MAC_STATUS_PCS_SYNCED 0x00000001 #define MAC_STATUS_SIGNAL_DET 0x00000002 -- GitLab From bc7959b2cbb57393b625b423c73e6fd07610257f Mon Sep 17 00:00:00 2001 From: Matt Carlson Date: Fri, 15 Aug 2008 14:08:55 -0700 Subject: [PATCH 462/750] tg3: Turn off ASF "driver alive" heartbeats for APE The ENABLE_ASF flag is set when DASH is enabled on the NIC, but DASH does not run on the RX CPU. Instead it runs on the APE. Consequently, the driver does not need to send "driver alive" updates to the RX CPU when the APE is present. Signed-off-by: Matt Carlson Signed-off-by: Michael Chan Signed-off-by: David S. Miller --- drivers/net/tg3.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c index 0ebf2ff60c4..e952b91ca2a 100644 --- a/drivers/net/tg3.c +++ b/drivers/net/tg3.c @@ -7862,7 +7862,8 @@ static void tg3_timer(unsigned long __opaque) * resets. */ if (!--tp->asf_counter) { - if (tp->tg3_flags & TG3_FLAG_ENABLE_ASF) { + if ((tp->tg3_flags & TG3_FLAG_ENABLE_ASF) && + !(tp->tg3_flags3 & TG3_FLG3_ENABLE_APE)) { u32 val; tg3_wait_for_event_ack(tp); -- GitLab From 4ba526ced990f4d61ee8d65fe8a6f0745e8e455c Mon Sep 17 00:00:00 2001 From: Matt Carlson Date: Fri, 15 Aug 2008 14:10:04 -0700 Subject: [PATCH 463/750] tg3: Fix firmware event timeouts The git commit 7c5026aa9b81dd45df8d3f4e0be73e485976a8b6 ("tg3: Add link state reporting to UMP firmware") introduced code that waits for previous firmware events to be serviced before attempting to submit a new event. Unfortunately that patch contained a bug that cause the driver to wait 2.5 seconds, rather than 2.5 milliseconds as intended. This patch fixes that bug. This bug revealed that not all firmware versions service driver events though. Since we do not know which versions of the firmware do and don't service these events, the driver needs some way to minimize the effects of the delay. This patch solves the problem by recording a jiffies timestamp when it submits an event to the hardware. If the jiffies counter shows that 2.5 milliseconds have already passed, a wait is not needed and the driver can proceed to submit a new event. Signed-off-by: Matt Carlson Signed-off-by: Michael Chan Signed-off-by: David S. Miller --- drivers/net/tg3.c | 53 +++++++++++++++++++++++++++++++++-------------- drivers/net/tg3.h | 3 +++ 2 files changed, 40 insertions(+), 16 deletions(-) diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c index e952b91ca2a..c26011eaa2b 100644 --- a/drivers/net/tg3.c +++ b/drivers/net/tg3.c @@ -1019,16 +1019,44 @@ static void tg3_mdio_fini(struct tg3 *tp) } } +/* tp->lock is held. */ +static inline void tg3_generate_fw_event(struct tg3 *tp) +{ + u32 val; + + val = tr32(GRC_RX_CPU_EVENT); + val |= GRC_RX_CPU_DRIVER_EVENT; + tw32_f(GRC_RX_CPU_EVENT, val); + + tp->last_event_jiffies = jiffies; +} + +#define TG3_FW_EVENT_TIMEOUT_USEC 2500 + /* tp->lock is held. */ static void tg3_wait_for_event_ack(struct tg3 *tp) { int i; + unsigned int delay_cnt; + long time_remain; + + /* If enough time has passed, no wait is necessary. */ + time_remain = (long)(tp->last_event_jiffies + 1 + + usecs_to_jiffies(TG3_FW_EVENT_TIMEOUT_USEC)) - + (long)jiffies; + if (time_remain < 0) + return; - /* Wait for up to 2.5 milliseconds */ - for (i = 0; i < 250000; i++) { + /* Check if we can shorten the wait time. */ + delay_cnt = jiffies_to_usecs(time_remain); + if (delay_cnt > TG3_FW_EVENT_TIMEOUT_USEC) + delay_cnt = TG3_FW_EVENT_TIMEOUT_USEC; + delay_cnt = (delay_cnt >> 3) + 1; + + for (i = 0; i < delay_cnt; i++) { if (!(tr32(GRC_RX_CPU_EVENT) & GRC_RX_CPU_DRIVER_EVENT)) break; - udelay(10); + udelay(8); } } @@ -1077,9 +1105,7 @@ static void tg3_ump_link_report(struct tg3 *tp) val = 0; tg3_write_mem(tp, NIC_SRAM_FW_CMD_DATA_MBOX + 12, val); - val = tr32(GRC_RX_CPU_EVENT); - val |= GRC_RX_CPU_DRIVER_EVENT; - tw32_f(GRC_RX_CPU_EVENT, val); + tg3_generate_fw_event(tp); } static void tg3_link_report(struct tg3 *tp) @@ -5953,6 +5979,7 @@ static int tg3_chip_reset(struct tg3 *tp) tg3_read_mem(tp, NIC_SRAM_DATA_CFG, &nic_cfg); if (nic_cfg & NIC_SRAM_DATA_CFG_ASF_ENABLE) { tp->tg3_flags |= TG3_FLAG_ENABLE_ASF; + tp->last_event_jiffies = jiffies; if (tp->tg3_flags2 & TG3_FLG2_5750_PLUS) tp->tg3_flags2 |= TG3_FLG2_ASF_NEW_HANDSHAKE; } @@ -5966,15 +5993,12 @@ static void tg3_stop_fw(struct tg3 *tp) { if ((tp->tg3_flags & TG3_FLAG_ENABLE_ASF) && !(tp->tg3_flags3 & TG3_FLG3_ENABLE_APE)) { - u32 val; - /* Wait for RX cpu to ACK the previous event. */ tg3_wait_for_event_ack(tp); tg3_write_mem(tp, NIC_SRAM_FW_CMD_MBOX, FWCMD_NICDRV_PAUSE_FW); - val = tr32(GRC_RX_CPU_EVENT); - val |= GRC_RX_CPU_DRIVER_EVENT; - tw32(GRC_RX_CPU_EVENT, val); + + tg3_generate_fw_event(tp); /* Wait for RX cpu to ACK this event. */ tg3_wait_for_event_ack(tp); @@ -7864,8 +7888,6 @@ static void tg3_timer(unsigned long __opaque) if (!--tp->asf_counter) { if ((tp->tg3_flags & TG3_FLAG_ENABLE_ASF) && !(tp->tg3_flags3 & TG3_FLG3_ENABLE_APE)) { - u32 val; - tg3_wait_for_event_ack(tp); tg3_write_mem(tp, NIC_SRAM_FW_CMD_MBOX, @@ -7873,9 +7895,8 @@ static void tg3_timer(unsigned long __opaque) tg3_write_mem(tp, NIC_SRAM_FW_CMD_LEN_MBOX, 4); /* 5 seconds timeout */ tg3_write_mem(tp, NIC_SRAM_FW_CMD_DATA_MBOX, 5); - val = tr32(GRC_RX_CPU_EVENT); - val |= GRC_RX_CPU_DRIVER_EVENT; - tw32_f(GRC_RX_CPU_EVENT, val); + + tg3_generate_fw_event(tp); } tp->asf_counter = tp->asf_multiplier; } diff --git a/drivers/net/tg3.h b/drivers/net/tg3.h index 377234947e4..f5b8cab8d4b 100644 --- a/drivers/net/tg3.h +++ b/drivers/net/tg3.h @@ -2432,7 +2432,10 @@ struct tg3 { struct tg3_ethtool_stats estats; struct tg3_ethtool_stats estats_prev; + union { unsigned long phy_crc_errors; + unsigned long last_event_jiffies; + }; u32 rx_offset; u32 tg3_flags; -- GitLab From 816f8b86621000fc82e16ae5f172164de761d5eb Mon Sep 17 00:00:00 2001 From: Stefan Buehler Date: Fri, 15 Aug 2008 14:10:54 -0700 Subject: [PATCH 464/750] tg3: fix 64 bit counter for ethtool stats Ethtool stats are 64-bits in length. net_device_stats members are unsigned long types. When gathering information for a get_ethtool_stats call, the driver will call a driver-private, inlined get_stat64() function, which returns an unsigned long value. This call will inadvertently mask off the upper 32-bits of a stat on 32-bit machines. This patch defines a new get_estat() inline function and modifies the ESTAT_ADD() macro to use it. Signed-off-by: Stefan Buehler Signed-off-by: Matt Carlson Signed-off-by: Michael Chan Signed-off-by: David S. Miller --- drivers/net/tg3.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c index c26011eaa2b..ada1d0d1104 100644 --- a/drivers/net/tg3.c +++ b/drivers/net/tg3.c @@ -8466,6 +8466,11 @@ static inline unsigned long get_stat64(tg3_stat64_t *val) return ret; } +static inline u64 get_estat64(tg3_stat64_t *val) +{ + return ((u64)val->high << 32) | ((u64)val->low); +} + static unsigned long calc_crc_errors(struct tg3 *tp) { struct tg3_hw_stats *hw_stats = tp->hw_stats; @@ -8494,7 +8499,7 @@ static unsigned long calc_crc_errors(struct tg3 *tp) #define ESTAT_ADD(member) \ estats->member = old_estats->member + \ - get_stat64(&hw_stats->member) + get_estat64(&hw_stats->member) static struct tg3_ethtool_stats *tg3_get_estats(struct tg3 *tp) { -- GitLab From 23197916c447a1623d196e6547781180905f0bb2 Mon Sep 17 00:00:00 2001 From: Matt Carlson Date: Fri, 15 Aug 2008 14:11:19 -0700 Subject: [PATCH 465/750] tg3: Update version to 3.94 This patch updates the version number to 3.94. Signed-off-by: Matt Carlson Signed-off-by: Michael Chan Signed-off-by: David S. Miller --- drivers/net/tg3.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c index ada1d0d1104..71d2c5cfdad 100644 --- a/drivers/net/tg3.c +++ b/drivers/net/tg3.c @@ -66,8 +66,8 @@ #define DRV_MODULE_NAME "tg3" #define PFX DRV_MODULE_NAME ": " -#define DRV_MODULE_VERSION "3.93" -#define DRV_MODULE_RELDATE "May 22, 2008" +#define DRV_MODULE_VERSION "3.94" +#define DRV_MODULE_RELDATE "August 14, 2008" #define TG3_DEF_MAC_MODE 0 #define TG3_DEF_RX_MODE 0 -- GitLab From e4119a43187139736750bad5d694c6a839df045d Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Fri, 15 Aug 2008 19:51:07 -0700 Subject: [PATCH 466/750] bridge: show offload settings Add more ethtool generic operations to dump the bridge offload settings. Signed-off-by: Stephen Hemminger Signed-off-by: David S. Miller --- net/bridge/br_device.c | 15 ++++++++++----- 1 file changed, 10 insertions(+), 5 deletions(-) diff --git a/net/bridge/br_device.c b/net/bridge/br_device.c index 9b58d70b0e7..4f52c3d50eb 100644 --- a/net/bridge/br_device.c +++ b/net/bridge/br_device.c @@ -148,11 +148,16 @@ static int br_set_tx_csum(struct net_device *dev, u32 data) } static struct ethtool_ops br_ethtool_ops = { - .get_drvinfo = br_getinfo, - .get_link = ethtool_op_get_link, - .set_sg = br_set_sg, - .set_tx_csum = br_set_tx_csum, - .set_tso = br_set_tso, + .get_drvinfo = br_getinfo, + .get_link = ethtool_op_get_link, + .get_tx_csum = ethtool_op_get_tx_csum, + .set_tx_csum = br_set_tx_csum, + .get_sg = ethtool_op_get_sg, + .set_sg = br_set_sg, + .get_tso = ethtool_op_get_tso, + .set_tso = br_set_tso, + .get_ufo = ethtool_op_get_ufo, + .get_flags = ethtool_op_get_flags, }; void br_dev_setup(struct net_device *dev) -- GitLab From f22f8567cb0a530d8958d177e0f268783bd0d894 Mon Sep 17 00:00:00 2001 From: Herbert Xu Date: Fri, 15 Aug 2008 14:52:08 -0700 Subject: [PATCH 467/750] loopback: Enable TSO This patch enables TSO since the loopback device is naturally capable of handling packets of any size. This also means that we won't enable GSO on lo which is good until GSO is fixed to preserve netfilter state as netfilter treats loopback packets in a special way. Signed-off-by: Herbert Xu Signed-off-by: David S. Miller --- drivers/net/loopback.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/drivers/net/loopback.c b/drivers/net/loopback.c index 49f6bc036a9..46e87cc8725 100644 --- a/drivers/net/loopback.c +++ b/drivers/net/loopback.c @@ -234,9 +234,7 @@ static void loopback_setup(struct net_device *dev) dev->type = ARPHRD_LOOPBACK; /* 0x0001*/ dev->flags = IFF_LOOPBACK; dev->features = NETIF_F_SG | NETIF_F_FRAGLIST -#ifdef LOOPBACK_TSO | NETIF_F_TSO -#endif | NETIF_F_NO_CSUM | NETIF_F_HIGHDMA | NETIF_F_LLTX -- GitLab From 7447ef63cf2dfdc444f4c72ae13f604350b2e25f Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Fri, 15 Aug 2008 14:54:03 -0700 Subject: [PATCH 468/750] loopback: Remove rest of LOOPBACK_TSO code. It hasn't been enabled for a long time and the generic GSO engine is better documentation of what is expected of a device implementing TSO. Signed-off-by: David S. Miller --- drivers/net/loopback.c | 62 ------------------------------------------ 1 file changed, 62 deletions(-) diff --git a/drivers/net/loopback.c b/drivers/net/loopback.c index 46e87cc8725..489d53be2f5 100644 --- a/drivers/net/loopback.c +++ b/drivers/net/loopback.c @@ -64,68 +64,6 @@ struct pcpu_lstats { unsigned long bytes; }; -/* KISS: just allocate small chunks and copy bits. - * - * So, in fact, this is documentation, explaining what we expect - * of largesending device modulo TCP checksum, which is ignored for loopback. - */ - -#ifdef LOOPBACK_TSO -static void emulate_large_send_offload(struct sk_buff *skb) -{ - struct iphdr *iph = ip_hdr(skb); - struct tcphdr *th = (struct tcphdr *)(skb_network_header(skb) + - (iph->ihl * 4)); - unsigned int doffset = (iph->ihl + th->doff) * 4; - unsigned int mtu = skb_shinfo(skb)->gso_size + doffset; - unsigned int offset = 0; - u32 seq = ntohl(th->seq); - u16 id = ntohs(iph->id); - - while (offset + doffset < skb->len) { - unsigned int frag_size = min(mtu, skb->len - offset) - doffset; - struct sk_buff *nskb = alloc_skb(mtu + 32, GFP_ATOMIC); - - if (!nskb) - break; - skb_reserve(nskb, 32); - skb_set_mac_header(nskb, -ETH_HLEN); - skb_reset_network_header(nskb); - iph = ip_hdr(nskb); - skb_copy_to_linear_data(nskb, skb_network_header(skb), - doffset); - if (skb_copy_bits(skb, - doffset + offset, - nskb->data + doffset, - frag_size)) - BUG(); - skb_put(nskb, doffset + frag_size); - nskb->ip_summed = CHECKSUM_UNNECESSARY; - nskb->dev = skb->dev; - nskb->priority = skb->priority; - nskb->protocol = skb->protocol; - nskb->dst = dst_clone(skb->dst); - memcpy(nskb->cb, skb->cb, sizeof(skb->cb)); - nskb->pkt_type = skb->pkt_type; - - th = (struct tcphdr *)(skb_network_header(nskb) + iph->ihl * 4); - iph->tot_len = htons(frag_size + doffset); - iph->id = htons(id); - iph->check = 0; - iph->check = ip_fast_csum((unsigned char *) iph, iph->ihl); - th->seq = htonl(seq); - if (offset + doffset + frag_size < skb->len) - th->fin = th->psh = 0; - netif_rx(nskb); - offset += frag_size; - seq += frag_size; - id++; - } - - dev_kfree_skb(skb); -} -#endif /* LOOPBACK_TSO */ - /* * The higher levels take care of making this non-reentrant (it's * called with bh's disabled). -- GitLab From 6f85a124d819e1cf33b16d064a6a656fd448a735 Mon Sep 17 00:00:00 2001 From: Herbert Xu Date: Fri, 15 Aug 2008 14:55:02 -0700 Subject: [PATCH 469/750] net: Preserve netfilter attributes in skb_gso_segment using __copy_skb_header skb_gso_segment didn't preserve some attributes in the original skb such as the netfilter fields. This was harmless until they were used which is the case for packets going through lo. This patch makes it call __copy_skb_header which also picks up some other missing attributes. Signed-off-by: Herbert Xu Signed-off-by: David S. Miller --- net/core/skbuff.c | 12 ++---------- 1 file changed, 2 insertions(+), 10 deletions(-) diff --git a/net/core/skbuff.c b/net/core/skbuff.c index 84640172d65..ca1ccdf1ef7 100644 --- a/net/core/skbuff.c +++ b/net/core/skbuff.c @@ -2256,14 +2256,7 @@ struct sk_buff *skb_segment(struct sk_buff *skb, int features) segs = nskb; tail = nskb; - nskb->dev = skb->dev; - skb_copy_queue_mapping(nskb, skb); - nskb->priority = skb->priority; - nskb->protocol = skb->protocol; - nskb->vlan_tci = skb->vlan_tci; - nskb->dst = dst_clone(skb->dst); - memcpy(nskb->cb, skb->cb, sizeof(skb->cb)); - nskb->pkt_type = skb->pkt_type; + __copy_skb_header(nskb, skb); nskb->mac_len = skb->mac_len; skb_reserve(nskb, headroom); @@ -2274,6 +2267,7 @@ struct sk_buff *skb_segment(struct sk_buff *skb, int features) skb_copy_from_linear_data(skb, skb_put(nskb, doffset), doffset); if (!sg) { + nskb->ip_summed = CHECKSUM_NONE; nskb->csum = skb_copy_and_csum_bits(skb, offset, skb_put(nskb, len), len, 0); @@ -2283,8 +2277,6 @@ struct sk_buff *skb_segment(struct sk_buff *skb, int features) frag = skb_shinfo(nskb)->frags; k = 0; - nskb->ip_summed = CHECKSUM_PARTIAL; - nskb->csum = skb->csum; skb_copy_from_linear_data_offset(skb, offset, skb_put(nskb, hsize), hsize); -- GitLab From 04a0551c87363f100b04d28d7a15a632b70e18e7 Mon Sep 17 00:00:00 2001 From: Herbert Xu Date: Fri, 15 Aug 2008 14:56:37 -0700 Subject: [PATCH 470/750] loopback: Drop obsolete ip_summed setting Now that the network stack can handle inbound packets with partial checksums, we should no longer clobber the ip_summed field in the loopback driver. This is because CHECKSUM_UNNECESSARY implies that the checksum field is actually valid which is not true for loopback packets since it's only partial (and thus complemented). This allows packets from lo to then be SNATed to an external source while still preserving the checksum's validity. Signed-off-by: Herbert Xu Signed-off-by: David S. Miller --- drivers/net/loopback.c | 3 --- 1 file changed, 3 deletions(-) diff --git a/drivers/net/loopback.c b/drivers/net/loopback.c index 489d53be2f5..3b43bfd85a0 100644 --- a/drivers/net/loopback.c +++ b/drivers/net/loopback.c @@ -75,9 +75,6 @@ static int loopback_xmit(struct sk_buff *skb, struct net_device *dev) skb_orphan(skb); skb->protocol = eth_type_trans(skb,dev); -#ifndef LOOPBACK_MUST_CHECKSUM - skb->ip_summed = CHECKSUM_UNNECESSARY; -#endif #ifdef LOOPBACK_TSO if (skb_is_gso(skb)) { -- GitLab From e3b99556975907530aeb9745e7b3945a0da48f17 Mon Sep 17 00:00:00 2001 From: Mark McLoughlin Date: Fri, 15 Aug 2008 15:09:56 -0700 Subject: [PATCH 471/750] tun: TUNGETIFF interface to query name and flags Add a TUNGETIFF interface so that userspace can query a tun/tap descriptor for its name and flags. This is needed because it is common for one app to create a tap interface, exec another app and pass it the file descriptor for the interface. Without TUNGETIFF the spawned app has no way of detecting wheter the interface has e.g. IFF_VNET_HDR set. Signed-off-by: Mark McLoughlin Acked-by: Max Krasnyansky Signed-off-by: David S. Miller --- drivers/net/tun.c | 39 +++++++++++++++++++++++++++++++++++++++ include/linux/if_tun.h | 1 + 2 files changed, 40 insertions(+) diff --git a/drivers/net/tun.c b/drivers/net/tun.c index e6bbc639c2d..95931a5a988 100644 --- a/drivers/net/tun.c +++ b/drivers/net/tun.c @@ -748,6 +748,36 @@ static int tun_set_iff(struct net *net, struct file *file, struct ifreq *ifr) return err; } +static int tun_get_iff(struct net *net, struct file *file, struct ifreq *ifr) +{ + struct tun_struct *tun = file->private_data; + + if (!tun) + return -EBADFD; + + DBG(KERN_INFO "%s: tun_get_iff\n", tun->dev->name); + + strcpy(ifr->ifr_name, tun->dev->name); + + ifr->ifr_flags = 0; + + if (ifr->ifr_flags & TUN_TUN_DEV) + ifr->ifr_flags |= IFF_TUN; + else + ifr->ifr_flags |= IFF_TAP; + + if (tun->flags & TUN_NO_PI) + ifr->ifr_flags |= IFF_NO_PI; + + if (tun->flags & TUN_ONE_QUEUE) + ifr->ifr_flags |= IFF_ONE_QUEUE; + + if (tun->flags & TUN_VNET_HDR) + ifr->ifr_flags |= IFF_VNET_HDR; + + return 0; +} + /* This is like a cut-down ethtool ops, except done via tun fd so no * privs required. */ static int set_offload(struct net_device *dev, unsigned long arg) @@ -833,6 +863,15 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file, DBG(KERN_INFO "%s: tun_chr_ioctl cmd %d\n", tun->dev->name, cmd); switch (cmd) { + case TUNGETIFF: + ret = tun_get_iff(current->nsproxy->net_ns, file, &ifr); + if (ret) + return ret; + + if (copy_to_user(argp, &ifr, sizeof(ifr))) + return -EFAULT; + break; + case TUNSETNOCSUM: /* Disable/Enable checksum */ if (arg) diff --git a/include/linux/if_tun.h b/include/linux/if_tun.h index 4c6307ad9fd..8529f57ba26 100644 --- a/include/linux/if_tun.h +++ b/include/linux/if_tun.h @@ -45,6 +45,7 @@ #define TUNGETFEATURES _IOR('T', 207, unsigned int) #define TUNSETOFFLOAD _IOW('T', 208, unsigned int) #define TUNSETTXFILTER _IOW('T', 209, unsigned int) +#define TUNGETIFF _IOR('T', 210, unsigned int) /* TUNSETIFF ifr flags */ #define IFF_TUN 0x0001 -- GitLab From db543c1f973cd1d557cc32ceee76737c1e4d2898 Mon Sep 17 00:00:00 2001 From: Rusty Russell Date: Fri, 15 Aug 2008 15:13:53 -0700 Subject: [PATCH 472/750] net: skb_copy_datagram_from_iovec() There's an skb_copy_datagram_iovec() to copy out of a paged skb, but nothing the other way around (because we don't do that). We want to allocate big skbs in tun.c, so let's add the function. It's a carbon copy of skb_copy_datagram_iovec() with enough changes to be annoying. Signed-off-by: Rusty Russell Signed-off-by: David S. Miller --- include/linux/skbuff.h | 4 ++ net/core/datagram.c | 87 ++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 91 insertions(+) diff --git a/include/linux/skbuff.h b/include/linux/skbuff.h index 358661c9990..90992371783 100644 --- a/include/linux/skbuff.h +++ b/include/linux/skbuff.h @@ -1452,6 +1452,10 @@ extern int skb_copy_datagram_iovec(const struct sk_buff *from, extern int skb_copy_and_csum_datagram_iovec(struct sk_buff *skb, int hlen, struct iovec *iov); +extern int skb_copy_datagram_from_iovec(struct sk_buff *skb, + int offset, + struct iovec *from, + int len); extern void skb_free_datagram(struct sock *sk, struct sk_buff *skb); extern int skb_kill_datagram(struct sock *sk, struct sk_buff *skb, unsigned int flags); diff --git a/net/core/datagram.c b/net/core/datagram.c index dd61dcad601..52f577a0f54 100644 --- a/net/core/datagram.c +++ b/net/core/datagram.c @@ -339,6 +339,93 @@ fault: return -EFAULT; } +/** + * skb_copy_datagram_from_iovec - Copy a datagram from an iovec. + * @skb: buffer to copy + * @offset: offset in the buffer to start copying to + * @from: io vector to copy to + * @len: amount of data to copy to buffer from iovec + * + * Returns 0 or -EFAULT. + * Note: the iovec is modified during the copy. + */ +int skb_copy_datagram_from_iovec(struct sk_buff *skb, int offset, + struct iovec *from, int len) +{ + int start = skb_headlen(skb); + int i, copy = start - offset; + + /* Copy header. */ + if (copy > 0) { + if (copy > len) + copy = len; + if (memcpy_fromiovec(skb->data + offset, from, copy)) + goto fault; + if ((len -= copy) == 0) + return 0; + offset += copy; + } + + /* Copy paged appendix. Hmm... why does this look so complicated? */ + for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) { + int end; + + WARN_ON(start > offset + len); + + end = start + skb_shinfo(skb)->frags[i].size; + if ((copy = end - offset) > 0) { + int err; + u8 *vaddr; + skb_frag_t *frag = &skb_shinfo(skb)->frags[i]; + struct page *page = frag->page; + + if (copy > len) + copy = len; + vaddr = kmap(page); + err = memcpy_fromiovec(vaddr + frag->page_offset + + offset - start, from, copy); + kunmap(page); + if (err) + goto fault; + + if (!(len -= copy)) + return 0; + offset += copy; + } + start = end; + } + + if (skb_shinfo(skb)->frag_list) { + struct sk_buff *list = skb_shinfo(skb)->frag_list; + + for (; list; list = list->next) { + int end; + + WARN_ON(start > offset + len); + + end = start + list->len; + if ((copy = end - offset) > 0) { + if (copy > len) + copy = len; + if (skb_copy_datagram_from_iovec(list, + offset - start, + from, copy)) + goto fault; + if ((len -= copy) == 0) + return 0; + offset += copy; + } + start = end; + } + } + if (!len) + return 0; + +fault: + return -EFAULT; +} +EXPORT_SYMBOL(skb_copy_datagram_from_iovec); + static int skb_copy_and_csum_datagram(const struct sk_buff *skb, int offset, u8 __user *to, int len, __wsum *csump) -- GitLab From f42157cb568c1eb02eca7df4da67553a9edae24a Mon Sep 17 00:00:00 2001 From: Rusty Russell Date: Fri, 15 Aug 2008 15:15:10 -0700 Subject: [PATCH 473/750] tun: fallback if skb_alloc() fails on big packets skb_alloc produces linear packets (using kmalloc()). That can fail, so should we fall back to making paged skbs. My original version of this patch always allocate paged skbs for big packets. But that made performance drop from 8.4 seconds to 8.8 seconds on 1G lguest->Host TCP xmit. So now we only do that as a fallback. Signed-off-by: Rusty Russell Acked-by: Max Krasnyansky Signed-off-by: David S. Miller --- drivers/net/tun.c | 66 ++++++++++++++++++++++++++++++++++++++++++++--- 1 file changed, 62 insertions(+), 4 deletions(-) diff --git a/drivers/net/tun.c b/drivers/net/tun.c index 95931a5a988..6daea0c9186 100644 --- a/drivers/net/tun.c +++ b/drivers/net/tun.c @@ -358,6 +358,66 @@ static unsigned int tun_chr_poll(struct file *file, poll_table * wait) return mask; } +/* prepad is the amount to reserve at front. len is length after that. + * linear is a hint as to how much to copy (usually headers). */ +static struct sk_buff *tun_alloc_skb(size_t prepad, size_t len, size_t linear, + gfp_t gfp) +{ + struct sk_buff *skb; + unsigned int i; + + skb = alloc_skb(prepad + len, gfp|__GFP_NOWARN); + if (skb) { + skb_reserve(skb, prepad); + skb_put(skb, len); + return skb; + } + + /* Under a page? Don't bother with paged skb. */ + if (prepad + len < PAGE_SIZE) + return NULL; + + /* Start with a normal skb, and add pages. */ + skb = alloc_skb(prepad + linear, gfp); + if (!skb) + return NULL; + + skb_reserve(skb, prepad); + skb_put(skb, linear); + + len -= linear; + + for (i = 0; i < MAX_SKB_FRAGS; i++) { + skb_frag_t *f = &skb_shinfo(skb)->frags[i]; + + f->page = alloc_page(gfp|__GFP_ZERO); + if (!f->page) + break; + + f->page_offset = 0; + f->size = PAGE_SIZE; + + skb->data_len += PAGE_SIZE; + skb->len += PAGE_SIZE; + skb->truesize += PAGE_SIZE; + skb_shinfo(skb)->nr_frags++; + + if (len < PAGE_SIZE) { + len = 0; + break; + } + len -= PAGE_SIZE; + } + + /* Too large, or alloc fail? */ + if (unlikely(len)) { + kfree_skb(skb); + skb = NULL; + } + + return skb; +} + /* Get packet from user space buffer */ static __inline__ ssize_t tun_get_user(struct tun_struct *tun, struct iovec *iv, size_t count) { @@ -391,14 +451,12 @@ static __inline__ ssize_t tun_get_user(struct tun_struct *tun, struct iovec *iv, return -EINVAL; } - if (!(skb = alloc_skb(len + align, GFP_KERNEL))) { + if (!(skb = tun_alloc_skb(align, len, gso.hdr_len, GFP_KERNEL))) { tun->dev->stats.rx_dropped++; return -ENOMEM; } - if (align) - skb_reserve(skb, align); - if (memcpy_fromiovec(skb_put(skb, len), iv, len)) { + if (skb_copy_datagram_from_iovec(skb, 0, iv, len)) { tun->dev->stats.rx_dropped++; kfree_skb(skb); return -EFAULT; -- GitLab From 08013fa353fdcfc0a03cae805393abfc56722387 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Fri, 15 Aug 2008 19:46:01 -0700 Subject: [PATCH 474/750] bnx2: Fix build with VLAN_8021Q disabled. Reported by Randy Dunlap. Signed-off-by: David S. Miller --- drivers/net/bnx2.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/bnx2.c b/drivers/net/bnx2.c index d4548101e49..2486a656f12 100644 --- a/drivers/net/bnx2.c +++ b/drivers/net/bnx2.c @@ -35,8 +35,8 @@ #include #include #include -#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE) #include +#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE) #define BCM_VLAN 1 #endif #include -- GitLab From ebb1951d3624c2f961abe676645c13e5a1145569 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Fri, 15 Aug 2008 19:57:57 -0700 Subject: [PATCH 475/750] lmb: Fix reserved region handling in lmb_enforce_memory_limit(). The idea of the implementation of this fix is from Michael Ellerman. This function has two loops, but they each interpret the memory_limit value differently. The first loop interprets it as a "size limit" whereas the second loop interprets it as an "address limit". Before the second loop runs, reset memory_limit to lmb_end_of_DRAM() so that it all works out. Signed-off-by: David S. Miller Acked-by: Michael Ellerman --- lib/lmb.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/lib/lmb.c b/lib/lmb.c index 5d7b9286503..97e54703708 100644 --- a/lib/lmb.c +++ b/lib/lmb.c @@ -462,6 +462,8 @@ void __init lmb_enforce_memory_limit(u64 memory_limit) if (lmb.memory.region[0].size < lmb.rmo_size) lmb.rmo_size = lmb.memory.region[0].size; + memory_limit = lmb_end_of_DRAM(); + /* And truncate any reserves above the limit also. */ for (i = 0; i < lmb.reserved.cnt; i++) { p = &lmb.reserved.region[i]; -- GitLab From 16f719de62809e224e37c320760c3ce59098d862 Mon Sep 17 00:00:00 2001 From: Nicolas Pitre Date: Tue, 12 Aug 2008 22:10:59 +0100 Subject: [PATCH 476/750] [ARM] 5196/1: fix inline asm constraints for preload With gcc 4.3 and later, a pointer that has already been dereferenced is assumed not to be null since it should have caused a segmentation fault otherwise, hence any subsequent test against NULL is optimized away. Current inline asm constraint used in the implementation of prefetch() makes gcc believe that the pointer is dereferenced even though the PLD instruction does not load any data and does not cause a segmentation fault on null pointers, which causes all sorts of interesting results when reaching the end of a linked lists for example. Let's use a better constraint to properly represent the actual usage of the pointer value. Problem reported by Chris Steel. Signed-off-by: Nicolas Pitre Signed-off-by: Russell King --- arch/arm/include/asm/processor.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/include/asm/processor.h b/arch/arm/include/asm/processor.h index b01d5e7e3d5..517a4d6ffc7 100644 --- a/arch/arm/include/asm/processor.h +++ b/arch/arm/include/asm/processor.h @@ -112,9 +112,9 @@ extern int kernel_thread(int (*fn)(void *), void *arg, unsigned long flags); static inline void prefetch(const void *ptr) { __asm__ __volatile__( - "pld\t%0" + "pld\t%a0" : - : "o" (*(char *)ptr) + : "p" (ptr) : "cc"); } -- GitLab From da4d77cda07c349d10be1398004ebdfd1a22c426 Mon Sep 17 00:00:00 2001 From: Russell King Date: Wed, 13 Aug 2008 21:56:24 +0100 Subject: [PATCH 477/750] [ARM] update mach-types Signed-off-by: Russell King --- arch/arm/tools/mach-types | 53 ++++++++++++++++++++++++++++++++++----- 1 file changed, 47 insertions(+), 6 deletions(-) diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types index 8b8f564c3aa..56281c030a7 100644 --- a/arch/arm/tools/mach-types +++ b/arch/arm/tools/mach-types @@ -12,7 +12,7 @@ # # http://www.arm.linux.org.uk/developer/machines/?action=new # -# Last update: Sun Jul 13 12:04:05 2008 +# Last update: Wed Aug 13 21:56:02 2008 # # machine_is_xxx CONFIG_xxxx MACH_TYPE_xxx number # @@ -843,7 +843,7 @@ borzoi MACH_BORZOI BORZOI 831 gecko MACH_GECKO GECKO 832 ds101 MACH_DS101 DS101 833 omap_palmtt2 MACH_OMAP_PALMTT2 OMAP_PALMTT2 834 -xscale_palmld MACH_XSCALE_PALMLD XSCALE_PALMLD 835 +palmld MACH_PALMLD PALMLD 835 cc9c MACH_CC9C CC9C 836 sbc1670 MACH_SBC1670 SBC1670 837 ixdp28x5 MACH_IXDP28X5 IXDP28X5 838 @@ -852,7 +852,7 @@ ml696k MACH_ML696K ML696K 840 arcom_zeus MACH_ARCOM_ZEUS ARCOM_ZEUS 841 osiris MACH_OSIRIS OSIRIS 842 maestro MACH_MAESTRO MAESTRO 843 -tunge2 MACH_TUNGE2 TUNGE2 844 +palmte2 MACH_PALMTE2 PALMTE2 844 ixbbm MACH_IXBBM IXBBM 845 mx27ads MACH_MX27ADS MX27ADS 846 ax8004 MACH_AX8004 AX8004 847 @@ -916,7 +916,7 @@ nxdb500 MACH_NXDB500 NXDB500 905 apf9328 MACH_APF9328 APF9328 906 omap_wipoq MACH_OMAP_WIPOQ OMAP_WIPOQ 907 omap_twip MACH_OMAP_TWIP OMAP_TWIP 908 -palmtreo650 MACH_PALMTREO650 PALMTREO650 909 +palmt650 MACH_PALMT650 PALMT650 909 acumen MACH_ACUMEN ACUMEN 910 xp100 MACH_XP100 XP100 911 fs2410 MACH_FS2410 FS2410 912 @@ -1096,7 +1096,7 @@ atc6 MACH_ATC6 ATC6 1086 multmdw MACH_MULTMDW MULTMDW 1087 mba2440 MACH_MBA2440 MBA2440 1088 ecsd MACH_ECSD ECSD 1089 -zire31 MACH_ZIRE31 ZIRE31 1090 +palmz31 MACH_PALMZ31 PALMZ31 1090 fsg MACH_FSG FSG 1091 razor101 MACH_RAZOR101 RAZOR101 1092 opera_tdm MACH_OPERA_TDM OPERA_TDM 1093 @@ -1810,7 +1810,7 @@ kriss_sensor MACH_KRISS_SENSOR KRISS_SENSOR 1819 pilz_pmi5 MACH_PILZ_PMI5 PILZ_PMI5 1820 jade MACH_JADE JADE 1821 ks8695_softplc MACH_KS8695_SOFTPLC KS8695_SOFTPLC 1822 -gprisc4 MACH_GPRISC4 GPRISC4 1823 +gprisc3 MACH_GPRISC4 GPRISC4 1823 stamp9260 MACH_STAMP9260 STAMP9260 1824 smdk6430 MACH_SMDK6430 SMDK6430 1825 smdkc100 MACH_SMDKC100 SMDKC100 1826 @@ -1820,3 +1820,44 @@ deister_eyecam MACH_DEISTER_EYECAM DEISTER_EYECAM 1829 at91sam9m10ek MACH_AT91SAM9M10EK AT91SAM9M10EK 1830 linkstation_produo MACH_LINKSTATION_PRODUO LINKSTATION_PRODUO 1831 hit_b0 MACH_HIT_B0 HIT_B0 1832 +adx_rmu MACH_ADX_RMU ADX_RMU 1833 +xg_cpe_main MACH_XG_CPE_MAIN XG_CPE_MAIN 1834 +edb9407a MACH_EDB9407A EDB9407A 1835 +dtb9608 MACH_DTB9608 DTB9608 1836 +em104v1 MACH_EM104V1 EM104V1 1837 +demo MACH_DEMO DEMO 1838 +logi9260 MACH_LOGI9260 LOGI9260 1839 +mx31_exm32 MACH_MX31_EXM32 MX31_EXM32 1840 +usb_a9g20 MACH_USB_A9G20 USB_A9G20 1841 +picproje2008 MACH_PICPROJE2008 PICPROJE2008 1842 +cs_e9315 MACH_CS_E9315 CS_E9315 1843 +qil_a9g20 MACH_QIL_A9G20 QIL_A9G20 1844 +sha_pon020 MACH_SHA_PON020 SHA_PON020 1845 +nad MACH_NAD NAD 1846 +sbc35_a9260 MACH_SBC35_A9260 SBC35_A9260 1847 +sbc35_a9g20 MACH_SBC35_A9G20 SBC35_A9G20 1848 +davinci_beginning MACH_DAVINCI_BEGINNING DAVINCI_BEGINNING 1849 +uwc MACH_UWC UWC 1850 +mxlads MACH_MXLADS MXLADS 1851 +htcnike MACH_HTCNIKE HTCNIKE 1852 +deister_pxa270 MACH_DEISTER_PXA270 DEISTER_PXA270 1853 +cme9210js MACH_CME9210JS CME9210JS 1854 +cc9p9360 MACH_CC9P9360 CC9P9360 1855 +mocha MACH_MOCHA MOCHA 1856 +wapd170ag MACH_WAPD170AG WAPD170AG 1857 +linkstation_mini MACH_LINKSTATION_MINI LINKSTATION_MINI 1858 +afeb9260 MACH_AFEB9260 AFEB9260 1859 +w90x900 MACH_W90X900 W90X900 1860 +w90x700 MACH_W90X700 W90X700 1861 +kt300ip MACH_KT300IP KT300IP 1862 +kt300ip_g20 MACH_KT300IP_G20 KT300IP_G20 1863 +srcm MACH_SRCM SRCM 1864 +wlnx_9260 MACH_WLNX_9260 WLNX_9260 1865 +openmoko_gta03 MACH_OPENMOKO_GTA03 OPENMOKO_GTA03 1866 +osprey2 MACH_OSPREY2 OSPREY2 1867 +kbio9260 MACH_KBIO9260 KBIO9260 1868 +ginza MACH_GINZA GINZA 1869 +a636n MACH_A636N A636N 1870 +imx27ipcam MACH_IMX27IPCAM IMX27IPCAM 1871 +nenoc MACH_NEMOC NEMOC 1872 +geneva MACH_GENEVA GENEVA 1873 -- GitLab From 8b5942c391ff92417b0a133abf7a970fa4fc942a Mon Sep 17 00:00:00 2001 From: Adrian Bunk Date: Sun, 10 Aug 2008 12:33:08 +0100 Subject: [PATCH 478/750] [ARM] Fix a pile of broken watchdog drivers These patches from Adrian fix: - ixp4xx_wdt: 20d35f3e50ea7e573f9568b9fce4e98523aaee5d CC drivers/watchdog/ixp4xx_wdt.o ixp4xx_wdt.c:32: error: expected '=', ',', ';', 'asm' or '__attribute__' ixp4xx_wdt.c: In function 'wdt_enable': ixp4xx_wdt.c:41: error: 'wdt_lock' undeclared (first use in this ixp4xx_wdt.c:41: error: (Each undeclared identifier is reported only ixp4xx_wdt.c:41: error: for each function it appears in.) ixp4xx_wdt.c: In function 'wdt_disable': ixp4xx_wdt.c:52: error: 'wdt_lock' undeclared (first use in this ixp4xx_wdt.c: In function 'ixp4xx_wdt_init': ixp4xx_wdt.c:186: error: 'wdt_lock' undeclared (first use in this make[3]: *** [drivers/watchdog/ixp4xx_wdt.o] Error 1 - at91rm9200_wdt: 2760600da2a13d5a2a335ba012d0f3ad5df4c098 CC drivers/watchdog/at91rm9200_wdt.o at91rm9200_wdt.c:188: error: 'at91_wdt_ioctl' undeclared here (not in a make[3]: *** [drivers/watchdog/at91rm9200_wdt.o] Error 1 - wdt285: d0e58eed05f9baf77c4f75e794ae245f6dae240a CC [M] drivers/watchdog/wdt285.o wdt285.c: In function 'footbridge_watchdog_init': wdt285.c:211: error: 'KERN_WARN' undeclared (first use in this function) wdt285.c:211: error: (Each undeclared identifier is reported only once wdt285.c:211: error: for each function it appears in.) wdt285.c:212: error: expected ')' before string constant make[3]: *** [drivers/watchdog/wdt285.o] Error 1 And this patch from rmk: - s3c2410_wdt: 41dc8b72e37c514f7332cbc3f3dd864910c2a1fa CC drivers/watchdog/s3c2410_wdt.o s3c2410_wdt.c: In function `s3c2410wdt_start': s3c2410_wdt.c:161: warning: `return' with a value, in function returning void Reported-by: Adrian Bunk Signed-off-by: Adrian Bunk Signed-off-by: Russell King --- drivers/watchdog/at91rm9200_wdt.c | 2 +- drivers/watchdog/ixp4xx_wdt.c | 2 +- drivers/watchdog/s3c2410_wdt.c | 2 -- drivers/watchdog/wdt285.c | 2 +- 4 files changed, 3 insertions(+), 5 deletions(-) diff --git a/drivers/watchdog/at91rm9200_wdt.c b/drivers/watchdog/at91rm9200_wdt.c index bacd867dd22..d061f0ad2d2 100644 --- a/drivers/watchdog/at91rm9200_wdt.c +++ b/drivers/watchdog/at91rm9200_wdt.c @@ -128,7 +128,7 @@ static struct watchdog_info at91_wdt_info = { /* * Handle commands from user-space. */ -static long at91_wdt_ioct(struct file *file, +static long at91_wdt_ioctl(struct file *file, unsigned int cmd, unsigned long arg) { void __user *argp = (void __user *)arg; diff --git a/drivers/watchdog/ixp4xx_wdt.c b/drivers/watchdog/ixp4xx_wdt.c index 41264a5f173..8302ef005be 100644 --- a/drivers/watchdog/ixp4xx_wdt.c +++ b/drivers/watchdog/ixp4xx_wdt.c @@ -29,7 +29,7 @@ static int nowayout = WATCHDOG_NOWAYOUT; static int heartbeat = 60; /* (secs) Default is 1 minute */ static unsigned long wdt_status; static unsigned long boot_status; -static spin_lock_t wdt_lock; +static DEFINE_SPINLOCK(wdt_lock); #define WDT_TICK_RATE (IXP4XX_PERIPHERAL_BUS_CLOCK * 1000000UL) diff --git a/drivers/watchdog/s3c2410_wdt.c b/drivers/watchdog/s3c2410_wdt.c index 3da2b90d2fe..22715e3be5e 100644 --- a/drivers/watchdog/s3c2410_wdt.c +++ b/drivers/watchdog/s3c2410_wdt.c @@ -157,8 +157,6 @@ static void s3c2410wdt_start(void) writel(wdt_count, wdt_base + S3C2410_WTCNT); writel(wtcon, wdt_base + S3C2410_WTCON); spin_unlock(&wdt_lock); - - return 0; } static int s3c2410wdt_set_heartbeat(int timeout) diff --git a/drivers/watchdog/wdt285.c b/drivers/watchdog/wdt285.c index c8d7f1b2df0..db362c34958 100644 --- a/drivers/watchdog/wdt285.c +++ b/drivers/watchdog/wdt285.c @@ -208,7 +208,7 @@ static int __init footbridge_watchdog_init(void) soft_margin); if (machine_is_cats()) - printk(KERN_WARN + printk(KERN_WARNING "Warning: Watchdog reset may not work on this machine.\n"); return 0; } -- GitLab From 06f579dee5dd75c2aaf8fe83d034b5470eeee2f4 Mon Sep 17 00:00:00 2001 From: "Yang, Bo" Date: Sun, 10 Aug 2008 12:42:37 -0700 Subject: [PATCH 479/750] [SCSI] megaraid_sas: add readl to force PCI posting flush MegaRAID SAS Driver get unexpected Interrupt. Add the dummy readl to force PCI flush will fix this issue. Signed-off-by: Bo Yang Signed-off-by: Andrew Morton Cc: Stable Tree Signed-off-by: James Bottomley --- drivers/scsi/megaraid/megaraid_sas.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/scsi/megaraid/megaraid_sas.c b/drivers/scsi/megaraid/megaraid_sas.c index fc7ac158476..d7b99843ca3 100644 --- a/drivers/scsi/megaraid/megaraid_sas.c +++ b/drivers/scsi/megaraid/megaraid_sas.c @@ -198,6 +198,9 @@ megasas_clear_intr_xscale(struct megasas_register_set __iomem * regs) */ writel(status, ®s->outbound_intr_status); + /* Dummy readl to force pci flush */ + readl(®s->outbound_intr_status); + return 0; } @@ -293,6 +296,9 @@ megasas_clear_intr_ppc(struct megasas_register_set __iomem * regs) */ writel(status, ®s->outbound_doorbell_clear); + /* Dummy readl to force pci flush */ + readl(®s->outbound_doorbell_clear); + return 0; } /** -- GitLab From 530e6fc1e05f14762aea954ca8d6422c5a7077c1 Mon Sep 17 00:00:00 2001 From: "Yang, Bo" Date: Sun, 10 Aug 2008 12:42:37 -0700 Subject: [PATCH 480/750] [SCSI] megaraid_sas: add the shutdown DCMD cmd to driver shutdown routine Add the shutdown DCMD cmd to driver shutdown routine to make megaraid sas FW shutdown proper. Signed-off-by: Bo Yang Signed-off-by: Andrew Morton Signed-off-by: James Bottomley --- drivers/scsi/megaraid/megaraid_sas.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/scsi/megaraid/megaraid_sas.c b/drivers/scsi/megaraid/megaraid_sas.c index d7b99843ca3..e880cd450e0 100644 --- a/drivers/scsi/megaraid/megaraid_sas.c +++ b/drivers/scsi/megaraid/megaraid_sas.c @@ -2863,6 +2863,7 @@ static void megasas_shutdown(struct pci_dev *pdev) { struct megasas_instance *instance = pci_get_drvdata(pdev); megasas_flush_cache(instance); + megasas_shutdown_controller(instance, MR_DCMD_CTRL_SHUTDOWN); } /** -- GitLab From 6610a6b354d6c3377a1e79cd1d760ffe4358245c Mon Sep 17 00:00:00 2001 From: "Yang, Bo" Date: Sun, 10 Aug 2008 12:42:38 -0700 Subject: [PATCH 481/750] [SCSI] megaraid_sas: add new controllers (0x78 0x79) Add the new controllers (0x78 0x79) support to the driver. Those controllers are LSI's next generation (gen2) SAS controllers. [akpm@linux-foundation.org: coding-style fixes] [akpm@linux-foundation.org: parenthesise a macro] Signed-off-by: Bo Yang Signed-off-by: Andrew Morton Signed-off-by: James Bottomley --- drivers/scsi/megaraid/megaraid_sas.c | 110 ++++++++++++++++++++++++++- drivers/scsi/megaraid/megaraid_sas.h | 4 + 2 files changed, 112 insertions(+), 2 deletions(-) diff --git a/drivers/scsi/megaraid/megaraid_sas.c b/drivers/scsi/megaraid/megaraid_sas.c index e880cd450e0..870dc1c6302 100644 --- a/drivers/scsi/megaraid/megaraid_sas.c +++ b/drivers/scsi/megaraid/megaraid_sas.c @@ -10,7 +10,7 @@ * 2 of the License, or (at your option) any later version. * * FILE : megaraid_sas.c - * Version : v00.00.03.20-rc1 + * Version : v00.00.04.01-rc1 * * Authors: * (email-id : megaraidlinux@lsi.com) @@ -71,6 +71,10 @@ static struct pci_device_id megasas_pci_table[] = { /* ppc IOP */ {PCI_DEVICE(PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_LSI_SAS1078DE)}, /* ppc IOP */ + {PCI_DEVICE(PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_LSI_SAS1078GEN2)}, + /* gen2*/ + {PCI_DEVICE(PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_LSI_SAS0079GEN2)}, + /* gen2*/ {PCI_DEVICE(PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_LSI_VERDE_ZCR)}, /* xscale IOP, vega */ {PCI_DEVICE(PCI_VENDOR_ID_DELL, PCI_DEVICE_ID_DELL_PERC5)}, @@ -323,6 +327,99 @@ static struct megasas_instance_template megasas_instance_template_ppc = { .read_fw_status_reg = megasas_read_fw_status_reg_ppc, }; +/** +* The following functions are defined for gen2 (deviceid : 0x78 0x79) +* controllers +*/ + +/** + * megasas_enable_intr_gen2 - Enables interrupts + * @regs: MFI register set + */ +static inline void +megasas_enable_intr_gen2(struct megasas_register_set __iomem *regs) +{ + writel(0xFFFFFFFF, &(regs)->outbound_doorbell_clear); + + /* write ~0x00000005 (4 & 1) to the intr mask*/ + writel(~MFI_GEN2_ENABLE_INTERRUPT_MASK, &(regs)->outbound_intr_mask); + + /* Dummy readl to force pci flush */ + readl(®s->outbound_intr_mask); +} + +/** + * megasas_disable_intr_gen2 - Disables interrupt + * @regs: MFI register set + */ +static inline void +megasas_disable_intr_gen2(struct megasas_register_set __iomem *regs) +{ + u32 mask = 0xFFFFFFFF; + writel(mask, ®s->outbound_intr_mask); + /* Dummy readl to force pci flush */ + readl(®s->outbound_intr_mask); +} + +/** + * megasas_read_fw_status_reg_gen2 - returns the current FW status value + * @regs: MFI register set + */ +static u32 +megasas_read_fw_status_reg_gen2(struct megasas_register_set __iomem *regs) +{ + return readl(&(regs)->outbound_scratch_pad); +} + +/** + * megasas_clear_interrupt_gen2 - Check & clear interrupt + * @regs: MFI register set + */ +static int +megasas_clear_intr_gen2(struct megasas_register_set __iomem *regs) +{ + u32 status; + /* + * Check if it is our interrupt + */ + status = readl(®s->outbound_intr_status); + + if (!(status & MFI_GEN2_ENABLE_INTERRUPT_MASK)) + return 1; + + /* + * Clear the interrupt by writing back the same value + */ + writel(status, ®s->outbound_doorbell_clear); + + /* Dummy readl to force pci flush */ + readl(®s->outbound_intr_status); + + return 0; +} +/** + * megasas_fire_cmd_gen2 - Sends command to the FW + * @frame_phys_addr : Physical address of cmd + * @frame_count : Number of frames for the command + * @regs : MFI register set + */ +static inline void +megasas_fire_cmd_gen2(dma_addr_t frame_phys_addr, u32 frame_count, + struct megasas_register_set __iomem *regs) +{ + writel((frame_phys_addr | (frame_count<<1))|1, + &(regs)->inbound_queue_port); +} + +static struct megasas_instance_template megasas_instance_template_gen2 = { + + .fire_cmd = megasas_fire_cmd_gen2, + .enable_intr = megasas_enable_intr_gen2, + .disable_intr = megasas_disable_intr_gen2, + .clear_intr = megasas_clear_intr_gen2, + .read_fw_status_reg = megasas_read_fw_status_reg_gen2, +}; + /** * This is the end of set of functions & definitions * specific to ppc (deviceid : 0x60) controllers @@ -1982,7 +2079,12 @@ static int megasas_init_mfi(struct megasas_instance *instance) /* * Map the message registers */ - instance->base_addr = pci_resource_start(instance->pdev, 0); + if ((instance->pdev->device == PCI_DEVICE_ID_LSI_SAS1078GEN2) || + (instance->pdev->device == PCI_DEVICE_ID_LSI_SAS0079GEN2)) { + instance->base_addr = pci_resource_start(instance->pdev, 1); + } else { + instance->base_addr = pci_resource_start(instance->pdev, 0); + } if (pci_request_regions(instance->pdev, "megasas: LSI")) { printk(KERN_DEBUG "megasas: IO memory region busy!\n"); @@ -2004,6 +2106,10 @@ static int megasas_init_mfi(struct megasas_instance *instance) case PCI_DEVICE_ID_LSI_SAS1078DE: instance->instancet = &megasas_instance_template_ppc; break; + case PCI_DEVICE_ID_LSI_SAS1078GEN2: + case PCI_DEVICE_ID_LSI_SAS0079GEN2: + instance->instancet = &megasas_instance_template_gen2; + break; case PCI_DEVICE_ID_LSI_SAS1064R: case PCI_DEVICE_ID_DELL_PERC5: default: diff --git a/drivers/scsi/megaraid/megaraid_sas.h b/drivers/scsi/megaraid/megaraid_sas.h index b0c41e67170..7072ff2cec0 100644 --- a/drivers/scsi/megaraid/megaraid_sas.h +++ b/drivers/scsi/megaraid/megaraid_sas.h @@ -28,6 +28,8 @@ #define PCI_DEVICE_ID_LSI_SAS1078R 0x0060 #define PCI_DEVICE_ID_LSI_SAS1078DE 0x007C #define PCI_DEVICE_ID_LSI_VERDE_ZCR 0x0413 +#define PCI_DEVICE_ID_LSI_SAS1078GEN2 0x0078 +#define PCI_DEVICE_ID_LSI_SAS0079GEN2 0x0079 /* * ===================================== @@ -580,6 +582,8 @@ struct megasas_ctrl_info { #define MEGASAS_COMPLETION_TIMER_INTERVAL (HZ/10) #define MFI_REPLY_1078_MESSAGE_INTERRUPT 0x80000000 +#define MFI_REPLY_GEN2_MESSAGE_INTERRUPT 0x00000001 +#define MFI_GEN2_ENABLE_INTERRUPT_MASK (0x00000001 | 0x00000004) /* * register set for both 1068 and 1078 controllers -- GitLab From 24541f99ba7231de26355d1cb87ab06e0f593efb Mon Sep 17 00:00:00 2001 From: "Yang, Bo" Date: Sun, 10 Aug 2008 12:42:39 -0700 Subject: [PATCH 482/750] [SCSI] megaraid_sas: version and Documentation Update Signed-off-by: Bo Yang Signed-off-by: Andrew Morton Signed-off-by: James Bottomley --- Documentation/scsi/ChangeLog.megaraid_sas | 23 +++++++++++++++++++++++ drivers/scsi/megaraid/megaraid_sas.h | 6 +++--- 2 files changed, 26 insertions(+), 3 deletions(-) diff --git a/Documentation/scsi/ChangeLog.megaraid_sas b/Documentation/scsi/ChangeLog.megaraid_sas index 716fcc1cafb..c851ef49779 100644 --- a/Documentation/scsi/ChangeLog.megaraid_sas +++ b/Documentation/scsi/ChangeLog.megaraid_sas @@ -1,3 +1,26 @@ + +1 Release Date : Thur.July. 24 11:41:51 PST 2008 - + (emaild-id:megaraidlinux@lsi.com) + Sumant Patro + Bo Yang + +2 Current Version : 00.00.04.01 +3 Older Version : 00.00.03.22 + +1. Add the new controller (0078, 0079) support to the driver + Those controllers are LSI's next generatation(gen2) SAS controllers. + +1 Release Date : Mon.June. 23 10:12:45 PST 2008 - + (emaild-id:megaraidlinux@lsi.com) + Sumant Patro + Bo Yang + +2 Current Version : 00.00.03.22 +3 Older Version : 00.00.03.20 + +1. Add shutdown DCMD cmd to the shutdown routine to make FW shutdown proper. +2. Unexpected interrupt occurs in HWR Linux driver, add the dumy readl pci flush will fix this issue. + 1 Release Date : Mon. March 10 11:02:31 PDT 2008 - (emaild-id:megaraidlinux@lsi.com) Sumant Patro diff --git a/drivers/scsi/megaraid/megaraid_sas.h b/drivers/scsi/megaraid/megaraid_sas.h index 7072ff2cec0..0d033248fdf 100644 --- a/drivers/scsi/megaraid/megaraid_sas.h +++ b/drivers/scsi/megaraid/megaraid_sas.h @@ -18,9 +18,9 @@ /* * MegaRAID SAS Driver meta data */ -#define MEGASAS_VERSION "00.00.03.20-rc1" -#define MEGASAS_RELDATE "March 10, 2008" -#define MEGASAS_EXT_VERSION "Mon. March 10 11:02:31 PDT 2008" +#define MEGASAS_VERSION "00.00.04.01" +#define MEGASAS_RELDATE "July 24, 2008" +#define MEGASAS_EXT_VERSION "Thu July 24 11:41:51 PST 2008" /* * Device IDs -- GitLab From 8479fca119fac63538af9e313ad0b8658cbbe662 Mon Sep 17 00:00:00 2001 From: Chandra Seetharaman Date: Tue, 12 Aug 2008 17:26:58 -0700 Subject: [PATCH 483/750] [SCSI] scsi_dh: Do not use scsilun in rdac hardware handler RDAC storage controller doesn't seem to use the scsilun format. It uses only the last byte for LUN. Signed-off-by: Chandra Seetharaman Signed-off-by: James Bottomley --- drivers/scsi/device_handler/scsi_dh_rdac.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/scsi/device_handler/scsi_dh_rdac.c b/drivers/scsi/device_handler/scsi_dh_rdac.c index b093a501f8a..86365461a1c 100644 --- a/drivers/scsi/device_handler/scsi_dh_rdac.c +++ b/drivers/scsi/device_handler/scsi_dh_rdac.c @@ -376,7 +376,7 @@ static int get_lun(struct scsi_device *sdev, struct rdac_dh_data *h) if (inqp->page_id[0] != 'e' || inqp->page_id[1] != 'd' || inqp->page_id[2] != 'i' || inqp->page_id[3] != 'd') return SCSI_DH_NOSYS; - h->lun = scsilun_to_int((struct scsi_lun *)inqp->lun); + h->lun = inqp->lun[7]; /* Uses only the last byte */ } return err; } -- GitLab From fe42625cdf0d4e06f01e365897a64b68d7f7de7d Mon Sep 17 00:00:00 2001 From: Chandra Seetharaman Date: Tue, 12 Aug 2008 17:26:59 -0700 Subject: [PATCH 484/750] [SCSI] scsi_dh: Initialize lun_state in check_ownership() lun_state need to be initialized inside check_ownership(). Signed-off-by: Chandra Seetharaman Signed-off-by: James Bottomley --- drivers/scsi/device_handler/scsi_dh_rdac.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/scsi/device_handler/scsi_dh_rdac.c b/drivers/scsi/device_handler/scsi_dh_rdac.c index 86365461a1c..518da832ad2 100644 --- a/drivers/scsi/device_handler/scsi_dh_rdac.c +++ b/drivers/scsi/device_handler/scsi_dh_rdac.c @@ -386,6 +386,7 @@ static int check_ownership(struct scsi_device *sdev, struct rdac_dh_data *h) int err; struct c9_inquiry *inqp; + h->lun_state = RDAC_LUN_UNOWNED; err = submit_inquiry(sdev, 0xC9, sizeof(struct c9_inquiry), h); if (err == SCSI_DH_OK) { inqp = &h->inq.c9; -- GitLab From 6390d1f33faecf48e31f27dd7dbe928540f8acfc Mon Sep 17 00:00:00 2001 From: Andrew Vasquez Date: Wed, 13 Aug 2008 21:36:56 -0700 Subject: [PATCH 485/750] [SCSI] qla2xxx: Correct synchronization of software/firmware fcport states. Greg Wettstein (greg@enjellic.com) noted: http://article.gmane.org/gmane.linux.scsi/43409 on a reboot of a previously recognized SCST target, the initiator driver would be unable to re-recognize the device as a target. It turns out that prior to the SCST software reloading and returning it's "target-capable" abilities in the PRLI payload, the HBA would be re-initialized as an initiator-only type port. Since initiators typically classify themselves as an FCP-2 capable device, both software and firmware do not perform an explicit logout during port-loss. Unfortunately, as can be seen by the failure case, when the port (now target-capable) returns, firmware performs an ADISC without a follow-on PRLI, leaving stale 'initiator-only' data in the firmware's port database. Correct the discrepancy by performing the explicit logout during the transport's request to terminate-rport-io, thus synchronizing port states and ensuring a follow-on PRLI is performed. Reported-by: Greg Wettstein Signed-off-by: Andrew Vasquez Cc: Stable Tree Signed-off-by: James Bottomley --- drivers/scsi/qla2xxx/qla_attr.c | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/drivers/scsi/qla2xxx/qla_attr.c b/drivers/scsi/qla2xxx/qla_attr.c index a319a20ed44..45e7dcb4b34 100644 --- a/drivers/scsi/qla2xxx/qla_attr.c +++ b/drivers/scsi/qla2xxx/qla_attr.c @@ -993,6 +993,17 @@ qla2x00_terminate_rport_io(struct fc_rport *rport) { fc_port_t *fcport = *(fc_port_t **)rport->dd_data; + /* + * At this point all fcport's software-states are cleared. Perform any + * final cleanup of firmware resources (PCBs and XCBs). + */ + if (fcport->loop_id != FC_NO_LOOP_ID) { + fcport->ha->isp_ops->fabric_logout(fcport->ha, fcport->loop_id, + fcport->d_id.b.domain, fcport->d_id.b.area, + fcport->d_id.b.al_pa); + fcport->loop_id = FC_NO_LOOP_ID; + } + qla2x00_abort_fcport_cmds(fcport); scsi_target_unblock(&rport->dev); } -- GitLab From a7a28504bfa61dc6caa495f55c52623d10b42b32 Mon Sep 17 00:00:00 2001 From: Andrew Vasquez Date: Wed, 13 Aug 2008 21:36:57 -0700 Subject: [PATCH 486/750] [SCSI] qla2xxx: Correct vport-state management issues during ISP-ABORT. * Use correct 'ha' to mark a device lost from ISR. I/Os will always be returned on the physical-HA. qla2x00_mark_device_lost() should be called with the HA bound to the fcport. * Mark *all* devices lost during ISP-ABORT (bighammer). These fixes correct issues discovered locally where during link-perturbation and heavy vport-I/O fcport/rport states would stray and an rport's scsi-target lost (timed-out). Signed-off-by: Andrew Vasquez Signed-off-by: James Bottomley --- drivers/scsi/qla2xxx/qla_init.c | 3 +++ drivers/scsi/qla2xxx/qla_isr.c | 7 +++---- 2 files changed, 6 insertions(+), 4 deletions(-) diff --git a/drivers/scsi/qla2xxx/qla_init.c b/drivers/scsi/qla2xxx/qla_init.c index 601a6b29750..e1de7a696bf 100644 --- a/drivers/scsi/qla2xxx/qla_init.c +++ b/drivers/scsi/qla2xxx/qla_init.c @@ -3251,6 +3251,7 @@ qla2x00_abort_isp(scsi_qla_host_t *ha) { int rval; uint8_t status = 0; + scsi_qla_host_t *vha; if (ha->flags.online) { ha->flags.online = 0; @@ -3265,6 +3266,8 @@ qla2x00_abort_isp(scsi_qla_host_t *ha) if (atomic_read(&ha->loop_state) != LOOP_DOWN) { atomic_set(&ha->loop_state, LOOP_DOWN); qla2x00_mark_all_devices_lost(ha, 0); + list_for_each_entry(vha, &ha->vp_list, vp_list) + qla2x00_mark_all_devices_lost(vha, 0); } else { if (!atomic_read(&ha->loop_down_timer)) atomic_set(&ha->loop_down_timer, diff --git a/drivers/scsi/qla2xxx/qla_isr.c b/drivers/scsi/qla2xxx/qla_isr.c index 874d802edb7..d6a1a6627b5 100644 --- a/drivers/scsi/qla2xxx/qla_isr.c +++ b/drivers/scsi/qla2xxx/qla_isr.c @@ -1184,9 +1184,8 @@ qla2x00_status_entry(scsi_qla_host_t *ha, void *pkt) atomic_read(&fcport->state))); cp->result = DID_BUS_BUSY << 16; - if (atomic_read(&fcport->state) == FCS_ONLINE) { - qla2x00_mark_device_lost(ha, fcport, 1, 1); - } + if (atomic_read(&fcport->state) == FCS_ONLINE) + qla2x00_mark_device_lost(fcport->ha, fcport, 1, 1); break; case CS_RESET: @@ -1229,7 +1228,7 @@ qla2x00_status_entry(scsi_qla_host_t *ha, void *pkt) /* Check to see if logout occurred. */ if ((le16_to_cpu(sts->status_flags) & SF_LOGOUT_SENT)) - qla2x00_mark_device_lost(ha, fcport, 1, 1); + qla2x00_mark_device_lost(fcport->ha, fcport, 1, 1); break; default: -- GitLab From bed475c4cde5d12f537f445bdd0a5a3bb5684481 Mon Sep 17 00:00:00 2001 From: Andrew Vasquez Date: Wed, 13 Aug 2008 21:36:58 -0700 Subject: [PATCH 487/750] [SCSI] qla2xxx: Don't leak SG-DMA mappings while aborting commands. Original code inadvertently cleared an SRB's 'flags' while aborting; causing a follow-on scsi_dma_unmap() to be potentially missed. Signed-off-by: Andrew Vasquez Signed-off-by: James Bottomley --- drivers/scsi/qla2xxx/qla_os.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/drivers/scsi/qla2xxx/qla_os.c b/drivers/scsi/qla2xxx/qla_os.c index 7c8af7ed2a5..c2092addb86 100644 --- a/drivers/scsi/qla2xxx/qla_os.c +++ b/drivers/scsi/qla2xxx/qla_os.c @@ -1080,9 +1080,7 @@ qla2x00_abort_all_cmds(scsi_qla_host_t *ha, int res) sp = ha->outstanding_cmds[cnt]; if (sp) { ha->outstanding_cmds[cnt] = NULL; - sp->flags = 0; sp->cmd->result = res; - sp->cmd->host_scribble = (unsigned char *)NULL; qla2x00_sp_compl(ha, sp); } } -- GitLab From 946fb8915a47bbd76de75b2ae7f1c7e92c0666ca Mon Sep 17 00:00:00 2001 From: Mike Hernandez Date: Wed, 13 Aug 2008 21:36:59 -0700 Subject: [PATCH 488/750] [SCSI] qla2xxx: Set npiv_supported flag for FCoE HBAs. Signed-off-by: Andrew Vasquez Signed-off-by: James Bottomley --- drivers/scsi/qla2xxx/qla_init.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/scsi/qla2xxx/qla_init.c b/drivers/scsi/qla2xxx/qla_init.c index e1de7a696bf..ee89ddd64aa 100644 --- a/drivers/scsi/qla2xxx/qla_init.c +++ b/drivers/scsi/qla2xxx/qla_init.c @@ -976,8 +976,9 @@ qla2x00_setup_chip(scsi_qla_host_t *ha) &ha->fw_attributes, &ha->fw_memory_size); qla2x00_resize_request_q(ha); ha->flags.npiv_supported = 0; - if ((IS_QLA24XX(ha) || IS_QLA25XX(ha)) && - (ha->fw_attributes & BIT_2)) { + if ((IS_QLA24XX(ha) || IS_QLA25XX(ha) || + IS_QLA84XX(ha)) && + (ha->fw_attributes & BIT_2)) { ha->flags.npiv_supported = 1; if ((!ha->max_npiv_vports) || ((ha->max_npiv_vports + 1) % -- GitLab From 19851f136ab37d7ac6f7c865329d13db54712ec0 Mon Sep 17 00:00:00 2001 From: Andrew Vasquez Date: Wed, 13 Aug 2008 21:37:00 -0700 Subject: [PATCH 489/750] [SCSI] qla2xxx: Reference proper ha during SBR handling. The executing-HA of an SRB can be referenced from the sp->fcport. Use this correct value while processing status-continuation data and abort processing. Signed-off-by: Andrew Vasquez Signed-off-by: James Bottomley --- drivers/scsi/qla2xxx/qla_isr.c | 7 ++++--- drivers/scsi/qla2xxx/qla_os.c | 3 ++- 2 files changed, 6 insertions(+), 4 deletions(-) diff --git a/drivers/scsi/qla2xxx/qla_isr.c b/drivers/scsi/qla2xxx/qla_isr.c index d6a1a6627b5..45a3b93eed5 100644 --- a/drivers/scsi/qla2xxx/qla_isr.c +++ b/drivers/scsi/qla2xxx/qla_isr.c @@ -879,11 +879,12 @@ qla2x00_handle_sense(srb_t *sp, uint8_t *sense_data, uint32_t sense_len) sp->request_sense_ptr += sense_len; sp->request_sense_length -= sense_len; if (sp->request_sense_length != 0) - sp->ha->status_srb = sp; + sp->fcport->ha->status_srb = sp; DEBUG5(printk("%s(): Check condition Sense data, scsi(%ld:%d:%d:%d) " - "cmd=%p pid=%ld\n", __func__, sp->ha->host_no, cp->device->channel, - cp->device->id, cp->device->lun, cp, cp->serial_number)); + "cmd=%p pid=%ld\n", __func__, sp->fcport->ha->host_no, + cp->device->channel, cp->device->id, cp->device->lun, cp, + cp->serial_number)); if (sense_len) DEBUG5(qla2x00_dump_buffer(cp->sense_buffer, CMD_ACTUAL_SNSLEN(cp))); diff --git a/drivers/scsi/qla2xxx/qla_os.c b/drivers/scsi/qla2xxx/qla_os.c index c2092addb86..e0880ad243b 100644 --- a/drivers/scsi/qla2xxx/qla_os.c +++ b/drivers/scsi/qla2xxx/qla_os.c @@ -780,7 +780,8 @@ qla2x00_eh_wait_for_pending_commands(scsi_qla_host_t *ha, unsigned int t, sp = pha->outstanding_cmds[cnt]; if (!sp) continue; - if (ha->vp_idx != sp->ha->vp_idx) + + if (ha->vp_idx != sp->fcport->ha->vp_idx) continue; match = 0; switch (type) { -- GitLab From c795c1e4b68a74536f0fb18744d0e381ceb1f37e Mon Sep 17 00:00:00 2001 From: Andrew Vasquez Date: Wed, 13 Aug 2008 21:37:01 -0700 Subject: [PATCH 490/750] [SCSI] qla2xxx: Explicitly tear-down vports during PCI remove_one(). During internal testing, we've seen issues (hangs) with the 'deferred' vport tear-down-processing typically accompanied with the fc_remove_host() call. This is due to the current implementation's back-end vport handling being performed by the physical-HA's DPC thread where premature shutdown could lead to latent vport requests without a processor. This should also address a problem reported by Gal Rosen (http://marc.info/?l=linux-scsi&m=121731664417358&w=2) where the driver would attempt to awaken a previously torn-down DPC thread from interrupt context by implicitly calling wake_up_process() rather than the driver's qla2xxx_wake_dpc() helper. Rather, than reshuffle the remove_one() device-removal code, during unload, depend on the driver's timer to wake-up the DPC process, by limiting wake-ups based on an 'unloading' flag. Signed-off-by: Andrew Vasquez Signed-off-by: James Bottomley --- drivers/scsi/qla2xxx/qla_def.h | 1 + drivers/scsi/qla2xxx/qla_mbx.c | 2 +- drivers/scsi/qla2xxx/qla_os.c | 13 ++++++++++--- 3 files changed, 12 insertions(+), 4 deletions(-) diff --git a/drivers/scsi/qla2xxx/qla_def.h b/drivers/scsi/qla2xxx/qla_def.h index 6da31ba9440..94a720eabfd 100644 --- a/drivers/scsi/qla2xxx/qla_def.h +++ b/drivers/scsi/qla2xxx/qla_def.h @@ -2237,6 +2237,7 @@ typedef struct scsi_qla_host { #define REGISTER_FDMI_NEEDED 26 #define FCPORT_UPDATE_NEEDED 27 #define VP_DPC_NEEDED 28 /* wake up for VP dpc handling */ +#define UNLOADING 29 uint32_t device_flags; #define DFLG_LOCAL_DEVICES BIT_0 diff --git a/drivers/scsi/qla2xxx/qla_mbx.c b/drivers/scsi/qla2xxx/qla_mbx.c index bc90d6b8d0a..813bc7784c0 100644 --- a/drivers/scsi/qla2xxx/qla_mbx.c +++ b/drivers/scsi/qla2xxx/qla_mbx.c @@ -2686,7 +2686,7 @@ qla24xx_report_id_acquisition(scsi_qla_host_t *ha, set_bit(VP_IDX_ACQUIRED, &vha->vp_flags); set_bit(VP_DPC_NEEDED, &ha->dpc_flags); - wake_up_process(ha->dpc_thread); + qla2xxx_wake_dpc(ha); } } diff --git a/drivers/scsi/qla2xxx/qla_os.c b/drivers/scsi/qla2xxx/qla_os.c index e0880ad243b..26afe44265c 100644 --- a/drivers/scsi/qla2xxx/qla_os.c +++ b/drivers/scsi/qla2xxx/qla_os.c @@ -1775,10 +1775,15 @@ probe_out: static void qla2x00_remove_one(struct pci_dev *pdev) { - scsi_qla_host_t *ha; + scsi_qla_host_t *ha, *vha, *temp; ha = pci_get_drvdata(pdev); + list_for_each_entry_safe(vha, temp, &ha->vp_list, vp_list) + fc_vport_terminate(vha->fc_vport); + + set_bit(UNLOADING, &ha->dpc_flags); + qla2x00_dfs_remove(ha); qla84xx_put_chip(ha); @@ -2450,8 +2455,10 @@ qla2x00_do_dpc(void *data) void qla2xxx_wake_dpc(scsi_qla_host_t *ha) { - if (ha->dpc_thread) - wake_up_process(ha->dpc_thread); + struct task_struct *t = ha->dpc_thread; + + if (!test_bit(UNLOADING, &ha->dpc_flags) && t) + wake_up_process(t); } /* -- GitLab From bcd2361d7eda10f85a103cbe70f7eebaeef03072 Mon Sep 17 00:00:00 2001 From: Andrew Vasquez Date: Wed, 13 Aug 2008 21:37:02 -0700 Subject: [PATCH 491/750] [SCSI] qla2xxx: Update version number to 8.02.01-k7. Signed-off-by: Andrew Vasquez Signed-off-by: James Bottomley --- drivers/scsi/qla2xxx/qla_version.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/scsi/qla2xxx/qla_version.h b/drivers/scsi/qla2xxx/qla_version.h index 676c390db35..4160e4caa7b 100644 --- a/drivers/scsi/qla2xxx/qla_version.h +++ b/drivers/scsi/qla2xxx/qla_version.h @@ -7,7 +7,7 @@ /* * Driver version */ -#define QLA2XXX_VERSION "8.02.01-k6" +#define QLA2XXX_VERSION "8.02.01-k7" #define QLA_DRIVER_MAJOR_VER 8 #define QLA_DRIVER_MINOR_VER 2 -- GitLab From 66dca9b8c50b5e59d3bea8b21cee5c6dae6c9c46 Mon Sep 17 00:00:00 2001 From: Joe Malicki Date: Thu, 14 Aug 2008 17:14:48 -0400 Subject: [PATCH 492/750] [SCSI] megaraid_sas: remove sysfs dbg_lvl world writeable permissions /sys/bus/pci/drivers/megaraid_sas/dbg_lvl defaults to being world-writable, which seems bad (letting any user affect kernel driver behavior and logging level). This turns off group and user write permissions, so that on typical production systems only root can write to it. [jejb: fix up rejections] Signed-off-by: Joseph Malicki Acked-by: "Yang, Bo" Signed-off-by: James Bottomley --- drivers/scsi/megaraid/megaraid_sas.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/scsi/megaraid/megaraid_sas.c b/drivers/scsi/megaraid/megaraid_sas.c index 870dc1c6302..97b763378e7 100644 --- a/drivers/scsi/megaraid/megaraid_sas.c +++ b/drivers/scsi/megaraid/megaraid_sas.c @@ -3405,7 +3405,7 @@ megasas_sysfs_set_dbg_lvl(struct device_driver *dd, const char *buf, size_t coun return retval; } -static DRIVER_ATTR(dbg_lvl, S_IRUGO|S_IWUGO, megasas_sysfs_show_dbg_lvl, +static DRIVER_ATTR(dbg_lvl, S_IRUGO|S_IWUSR, megasas_sysfs_show_dbg_lvl, megasas_sysfs_set_dbg_lvl); static ssize_t -- GitLab From 004dd5e88673516a408f0e8e43edbe6a4424be2f Mon Sep 17 00:00:00 2001 From: Brian King Date: Fri, 15 Aug 2008 10:48:47 -0500 Subject: [PATCH 493/750] [SCSI] ibmvscsi: Fixup desired DMA value for shared memory partitions When running ibmvscsi in a shared memory partition, it must provide a default value for the amount of DMA resources it will need in order to perform reasonably well. This was being calculated in sectors rather than bytes, as it should. This patch fixes this. Signed-off-by: Brian King Signed-off-by: James Bottomley --- drivers/scsi/ibmvscsi/ibmvscsi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/scsi/ibmvscsi/ibmvscsi.c b/drivers/scsi/ibmvscsi/ibmvscsi.c index 6b24b9cdb04..7b1502c0ab6 100644 --- a/drivers/scsi/ibmvscsi/ibmvscsi.c +++ b/drivers/scsi/ibmvscsi/ibmvscsi.c @@ -1636,7 +1636,7 @@ static unsigned long ibmvscsi_get_desired_dma(struct vio_dev *vdev) unsigned long desired_io = max_requests * sizeof(union viosrp_iu); /* add io space for sg data */ - desired_io += (IBMVSCSI_MAX_SECTORS_DEFAULT * + desired_io += (IBMVSCSI_MAX_SECTORS_DEFAULT * 512 * IBMVSCSI_CMDS_PER_LUN_DEFAULT); return desired_io; -- GitLab From 574047f96a302cbca2f9bfafd78b1869b6a900bf Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Marek=20Va=C5=A1ut?= Date: Sat, 16 Aug 2008 15:34:11 +0100 Subject: [PATCH 494/750] [ARM] 5198/1: PalmTX: PCMCIA fixes Fix GPIO handling in the PCMCIA driver. Signed-off-by: Marek Vasut Signed-off-by: Russell King --- drivers/pcmcia/pxa2xx_palmtx.c | 49 ++++++++++++++++++++++++++++++++-- 1 file changed, 47 insertions(+), 2 deletions(-) diff --git a/drivers/pcmcia/pxa2xx_palmtx.c b/drivers/pcmcia/pxa2xx_palmtx.c index a8771ffc61e..e07b5c51ec5 100644 --- a/drivers/pcmcia/pxa2xx_palmtx.c +++ b/drivers/pcmcia/pxa2xx_palmtx.c @@ -23,12 +23,57 @@ static int palmtx_pcmcia_hw_init(struct soc_pcmcia_socket *skt) { - skt->irq = IRQ_GPIO(GPIO_NR_PALMTX_PCMCIA_READY); + int ret; + + ret = gpio_request(GPIO_NR_PALMTX_PCMCIA_POWER1, "PCMCIA PWR1"); + if (ret) + goto err1; + ret = gpio_direction_output(GPIO_NR_PALMTX_PCMCIA_POWER1, 0); + if (ret) + goto err2; + + ret = gpio_request(GPIO_NR_PALMTX_PCMCIA_POWER2, "PCMCIA PWR2"); + if (ret) + goto err2; + ret = gpio_direction_output(GPIO_NR_PALMTX_PCMCIA_POWER2, 0); + if (ret) + goto err3; + + ret = gpio_request(GPIO_NR_PALMTX_PCMCIA_RESET, "PCMCIA RST"); + if (ret) + goto err3; + ret = gpio_direction_output(GPIO_NR_PALMTX_PCMCIA_RESET, 1); + if (ret) + goto err4; + + ret = gpio_request(GPIO_NR_PALMTX_PCMCIA_READY, "PCMCIA RDY"); + if (ret) + goto err4; + ret = gpio_direction_input(GPIO_NR_PALMTX_PCMCIA_READY); + if (ret) + goto err5; + + skt->irq = gpio_to_irq(GPIO_NR_PALMTX_PCMCIA_READY); return 0; + +err5: + gpio_free(GPIO_NR_PALMTX_PCMCIA_READY); +err4: + gpio_free(GPIO_NR_PALMTX_PCMCIA_RESET); +err3: + gpio_free(GPIO_NR_PALMTX_PCMCIA_POWER2); +err2: + gpio_free(GPIO_NR_PALMTX_PCMCIA_POWER1); +err1: + return ret; } static void palmtx_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt) { + gpio_free(GPIO_NR_PALMTX_PCMCIA_READY); + gpio_free(GPIO_NR_PALMTX_PCMCIA_RESET); + gpio_free(GPIO_NR_PALMTX_PCMCIA_POWER2); + gpio_free(GPIO_NR_PALMTX_PCMCIA_POWER1); } static void palmtx_pcmcia_socket_state(struct soc_pcmcia_socket *skt, @@ -109,7 +154,7 @@ static void __exit palmtx_pcmcia_exit(void) platform_device_unregister(palmtx_pcmcia_device); } -fs_initcall(palmtx_pcmcia_init); +module_init(palmtx_pcmcia_init); module_exit(palmtx_pcmcia_exit); MODULE_AUTHOR("Marek Vasut "); -- GitLab From cb47729bdaf49fe5e9dd2c41554f44a77b5cd590 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Sat, 16 Aug 2008 03:59:11 -0400 Subject: [PATCH 495/750] [ARM] pxafb: fix the incorrect configuration of GPIO77 as ACBIAS for TFT LCD Signed-off-by: Eric Miao Tested-by: Robert Jarzmik Tested-by: Alex Osborne Signed-off-by: Russell King --- drivers/video/pxafb.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/video/pxafb.c b/drivers/video/pxafb.c index e7aa7ae8fca..bef35afa258 100644 --- a/drivers/video/pxafb.c +++ b/drivers/video/pxafb.c @@ -1031,7 +1031,9 @@ static void pxafb_setup_gpio(struct pxafb_info *fbi) pxa_gpio_mode(GPIO74_LCD_FCLK_MD); pxa_gpio_mode(GPIO75_LCD_LCLK_MD); pxa_gpio_mode(GPIO76_LCD_PCLK_MD); - pxa_gpio_mode(GPIO77_LCD_ACBIAS_MD); + + if ((lccr0 & LCCR0_PAS) == 0) + pxa_gpio_mode(GPIO77_LCD_ACBIAS_MD); } static void pxafb_enable_controller(struct pxafb_info *fbi) -- GitLab From 9a1ac7e498b9fc367235aabeb5b86c1319db1de9 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Fri, 15 Aug 2008 02:50:44 -0400 Subject: [PATCH 496/750] [ARM] pxafb: add flag to specify output format on LDD pins when base is RGBT16 Another fix of inconsistent shift of the LCD_BIAS_ACTIVE_* and LCD_PCLK_EDGE_* is also included. Signed-off-by: Eric Miao Signed-off-by: Russell King --- arch/arm/mach-pxa/include/mach/pxafb.h | 10 ++++++---- drivers/video/pxafb.c | 2 ++ 2 files changed, 8 insertions(+), 4 deletions(-) diff --git a/arch/arm/mach-pxa/include/mach/pxafb.h b/arch/arm/mach-pxa/include/mach/pxafb.h index 65447549616..8e591118371 100644 --- a/arch/arm/mach-pxa/include/mach/pxafb.h +++ b/arch/arm/mach-pxa/include/mach/pxafb.h @@ -28,6 +28,7 @@ * bits 10-17 : for AC Bias Pin Frequency * bit 18 : for output enable polarity * bit 19 : for pixel clock edge + * bit 20 : for output pixel format when base is RGBT16 */ #define LCD_CONN_TYPE(_x) ((_x) & 0x0f) #define LCD_CONN_WIDTH(_x) (((_x) >> 4) & 0x1f) @@ -53,10 +54,11 @@ #define LCD_SMART_PANEL_18BPP ((18 << 4) | LCD_TYPE_SMART_PANEL) #define LCD_AC_BIAS_FREQ(x) (((x) & 0xff) << 10) -#define LCD_BIAS_ACTIVE_HIGH (0 << 17) -#define LCD_BIAS_ACTIVE_LOW (1 << 17) -#define LCD_PCLK_EDGE_RISE (0 << 18) -#define LCD_PCLK_EDGE_FALL (1 << 18) +#define LCD_BIAS_ACTIVE_HIGH (0 << 18) +#define LCD_BIAS_ACTIVE_LOW (1 << 18) +#define LCD_PCLK_EDGE_RISE (0 << 19) +#define LCD_PCLK_EDGE_FALL (1 << 19) +#define LCD_ALTERNATE_MAPPING (1 << 20) /* * This structure describes the machine which we are running on. diff --git a/drivers/video/pxafb.c b/drivers/video/pxafb.c index bef35afa258..fa108dad09b 100644 --- a/drivers/video/pxafb.c +++ b/drivers/video/pxafb.c @@ -1402,6 +1402,8 @@ static void pxafb_decode_mach_info(struct pxafb_info *fbi, if (lcd_conn == LCD_MONO_STN_8BPP) fbi->lccr0 |= LCCR0_DPD; + fbi->lccr0 |= (lcd_conn & LCD_ALTERNATE_MAPPING) ? LCCR0_LDDALT : 0; + fbi->lccr3 = LCCR3_Acb((inf->lcd_conn >> 10) & 0xff); fbi->lccr3 |= (lcd_conn & LCD_BIAS_ACTIVE_LOW) ? LCCR3_OEP : 0; fbi->lccr3 |= (lcd_conn & LCD_PCLK_EDGE_FALL) ? LCCR3_PCP : 0; -- GitLab From 4f3e2664622d23a17c6fc45a4df4c35cd2612ffb Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Sat, 16 Aug 2008 03:50:51 -0400 Subject: [PATCH 497/750] [ARM] pxafb: fix the warning of incorrect lccr when lcd_conn is specified The newly introduced "lcd_conn" field for connected LCD panel type will cause the original code to generate the warnings of incorrect lccr*. This is unnecessary since well encoded LCD_* flags will not generate incorrect combinition of lccr* bits. Skip the check if "lcd_conn" is specified. Signed-off-by: Eric Miao Signed-off-by: Russell King --- drivers/video/pxafb.c | 62 +++++++++++++++++++++++++------------------ 1 file changed, 36 insertions(+), 26 deletions(-) diff --git a/drivers/video/pxafb.c b/drivers/video/pxafb.c index fa108dad09b..97204497d9f 100644 --- a/drivers/video/pxafb.c +++ b/drivers/video/pxafb.c @@ -1677,53 +1677,63 @@ MODULE_PARM_DESC(options, "LCD parameters (see Documentation/fb/pxafb.txt)"); #define pxafb_setup_options() (0) #endif -static int __devinit pxafb_probe(struct platform_device *dev) -{ - struct pxafb_info *fbi; - struct pxafb_mach_info *inf; - struct resource *r; - int irq, ret; - - dev_dbg(&dev->dev, "pxafb_probe\n"); - - inf = dev->dev.platform_data; - ret = -ENOMEM; - fbi = NULL; - if (!inf) - goto failed; - - ret = pxafb_parse_options(&dev->dev, g_options); - if (ret < 0) - goto failed; - #ifdef DEBUG_VAR - /* Check for various illegal bit-combinations. Currently only - * a warning is given. */ +/* Check for various illegal bit-combinations. Currently only + * a warning is given. */ +static void __devinit pxafb_check_options(struct device *dev, + struct pxafb_mach_info *inf) +{ + if (inf->lcd_conn) + return; if (inf->lccr0 & LCCR0_INVALID_CONFIG_MASK) - dev_warn(&dev->dev, "machine LCCR0 setting contains " + dev_warn(dev, "machine LCCR0 setting contains " "illegal bits: %08x\n", inf->lccr0 & LCCR0_INVALID_CONFIG_MASK); if (inf->lccr3 & LCCR3_INVALID_CONFIG_MASK) - dev_warn(&dev->dev, "machine LCCR3 setting contains " + dev_warn(dev, "machine LCCR3 setting contains " "illegal bits: %08x\n", inf->lccr3 & LCCR3_INVALID_CONFIG_MASK); if (inf->lccr0 & LCCR0_DPD && ((inf->lccr0 & LCCR0_PAS) != LCCR0_Pas || (inf->lccr0 & LCCR0_SDS) != LCCR0_Sngl || (inf->lccr0 & LCCR0_CMS) != LCCR0_Mono)) - dev_warn(&dev->dev, "Double Pixel Data (DPD) mode is " + dev_warn(dev, "Double Pixel Data (DPD) mode is " "only valid in passive mono" " single panel mode\n"); if ((inf->lccr0 & LCCR0_PAS) == LCCR0_Act && (inf->lccr0 & LCCR0_SDS) == LCCR0_Dual) - dev_warn(&dev->dev, "Dual panel only valid in passive mode\n"); + dev_warn(dev, "Dual panel only valid in passive mode\n"); if ((inf->lccr0 & LCCR0_PAS) == LCCR0_Pas && (inf->modes->upper_margin || inf->modes->lower_margin)) - dev_warn(&dev->dev, "Upper and lower margins must be 0 in " + dev_warn(dev, "Upper and lower margins must be 0 in " "passive mode\n"); +} +#else +#define pxafb_check_options(...) do {} while (0) #endif +static int __devinit pxafb_probe(struct platform_device *dev) +{ + struct pxafb_info *fbi; + struct pxafb_mach_info *inf; + struct resource *r; + int irq, ret; + + dev_dbg(&dev->dev, "pxafb_probe\n"); + + inf = dev->dev.platform_data; + ret = -ENOMEM; + fbi = NULL; + if (!inf) + goto failed; + + ret = pxafb_parse_options(&dev->dev, g_options); + if (ret < 0) + goto failed; + + pxafb_check_options(&dev->dev, inf); + dev_dbg(&dev->dev, "got a %dx%dx%d LCD\n", inf->modes->xres, inf->modes->yres, -- GitLab From 3eddc569770a76f2ca65621cdde3c0a2552b5b0c Mon Sep 17 00:00:00 2001 From: Brian King Date: Fri, 15 Aug 2008 10:59:21 -0500 Subject: [PATCH 498/750] [SCSI] ibmvfc: Fix another hang on module removal This fixes a hang on module removal. The module removal code was setting the hosts's state to IBMVFC_HOST_OFFLINE before tearing down the kernel thread, but, due to a bug in ibmvfc_wait_while_resetting, was not waiting for the kernel thread's offlining work to be done prior to destroying the kernel thread, which left the scsi host in a blocked state which we never got out of. Signed-off-by: Brian King Signed-off-by: James Bottomley --- drivers/scsi/ibmvscsi/ibmvfc.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/scsi/ibmvscsi/ibmvfc.c b/drivers/scsi/ibmvscsi/ibmvfc.c index ae560bc04f9..ee11568d581 100644 --- a/drivers/scsi/ibmvscsi/ibmvfc.c +++ b/drivers/scsi/ibmvscsi/ibmvfc.c @@ -1059,9 +1059,10 @@ static void ibmvfc_get_starget_port_id(struct scsi_target *starget) static int ibmvfc_wait_while_resetting(struct ibmvfc_host *vhost) { long timeout = wait_event_timeout(vhost->init_wait_q, - (vhost->state == IBMVFC_ACTIVE || - vhost->state == IBMVFC_HOST_OFFLINE || - vhost->state == IBMVFC_LINK_DEAD), + ((vhost->state == IBMVFC_ACTIVE || + vhost->state == IBMVFC_HOST_OFFLINE || + vhost->state == IBMVFC_LINK_DEAD) && + vhost->action == IBMVFC_HOST_ACTION_NONE), (init_timeout * HZ)); return timeout ? 0 : -EIO; -- GitLab From 915be024414c52e311f795566ac938223ba3c847 Mon Sep 17 00:00:00 2001 From: Brian King Date: Fri, 15 Aug 2008 10:59:22 -0500 Subject: [PATCH 499/750] [SCSI] ibmvfc: Fixup host state during reinit If an ELS is received while the virtual fibre channel adapter is going through its discovery, a flag is set which causes discovery to get re-driven. However, the hosts's state does not get set back to IBMVFC_INITIALIZING and scsi_block_requests does not get called again, which can result in queuecommand ops getting sent during discovery. This should not occur and may cause problems. One example is that we may no longer be logged into the target we send the command to, resulting in a failure which should not have occurred. Signed-off-by: Brian King Signed-off-by: James Bottomley --- drivers/scsi/ibmvscsi/ibmvfc.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/scsi/ibmvscsi/ibmvfc.c b/drivers/scsi/ibmvscsi/ibmvfc.c index ee11568d581..406ab27f80e 100644 --- a/drivers/scsi/ibmvscsi/ibmvfc.c +++ b/drivers/scsi/ibmvscsi/ibmvfc.c @@ -3602,8 +3602,9 @@ static void ibmvfc_do_work(struct ibmvfc_host *vhost) } } - if (vhost->reinit) { + if (vhost->reinit && !ibmvfc_set_host_state(vhost, IBMVFC_INITIALIZING)) { vhost->reinit = 0; + scsi_block_requests(vhost->host); ibmvfc_set_host_action(vhost, IBMVFC_HOST_ACTION_QUERY); } else { ibmvfc_set_host_action(vhost, IBMVFC_HOST_ACTION_NONE); -- GitLab From cf6f10d794ab4a9bd84fce345c3947588670d5f5 Mon Sep 17 00:00:00 2001 From: Brian King Date: Fri, 15 Aug 2008 10:59:23 -0500 Subject: [PATCH 500/750] [SCSI] ibmvfc: Fix for lost async events If the client virtual fibre channel adapter is already logged into the server and does an NPIV Login again, the async queue, which is used for reporting Link Up/Link Down type of events, does not get reset on the server side. Fix up the client driver so that we also do not reset it. This fixes a problem of lost async events following relogins. Signed-off-by: Brian King Signed-off-by: James Bottomley --- drivers/scsi/ibmvscsi/ibmvfc.c | 18 +++++++++++------- 1 file changed, 11 insertions(+), 7 deletions(-) diff --git a/drivers/scsi/ibmvscsi/ibmvfc.c b/drivers/scsi/ibmvscsi/ibmvfc.c index 406ab27f80e..58f8c9e39ae 100644 --- a/drivers/scsi/ibmvscsi/ibmvfc.c +++ b/drivers/scsi/ibmvscsi/ibmvfc.c @@ -556,11 +556,12 @@ static void ibmvfc_link_down(struct ibmvfc_host *vhost, /** * ibmvfc_init_host - Start host initialization * @vhost: ibmvfc host struct + * @relogin: is this a re-login? * * Return value: * nothing **/ -static void ibmvfc_init_host(struct ibmvfc_host *vhost) +static void ibmvfc_init_host(struct ibmvfc_host *vhost, int relogin) { struct ibmvfc_target *tgt; @@ -574,6 +575,11 @@ static void ibmvfc_init_host(struct ibmvfc_host *vhost) } if (!ibmvfc_set_host_state(vhost, IBMVFC_INITIALIZING)) { + if (!relogin) { + memset(vhost->async_crq.msgs, 0, PAGE_SIZE); + vhost->async_crq.cur = 0; + } + list_for_each_entry(tgt, &vhost->targets, queue) tgt->need_login = 1; scsi_block_requests(vhost->host); @@ -2084,11 +2090,11 @@ static void ibmvfc_handle_async(struct ibmvfc_async_crq *crq, case IBMVFC_AE_LINK_UP: case IBMVFC_AE_RESUME: vhost->events_to_log |= IBMVFC_AE_LINKUP; - ibmvfc_init_host(vhost); + ibmvfc_init_host(vhost, 1); break; case IBMVFC_AE_SCN_FABRIC: vhost->events_to_log |= IBMVFC_AE_RSCN; - ibmvfc_init_host(vhost); + ibmvfc_init_host(vhost, 1); break; case IBMVFC_AE_SCN_NPORT: case IBMVFC_AE_SCN_GROUP: @@ -2134,13 +2140,13 @@ static void ibmvfc_handle_crq(struct ibmvfc_crq *crq, struct ibmvfc_host *vhost) /* Send back a response */ rc = ibmvfc_send_crq_init_complete(vhost); if (rc == 0) - ibmvfc_init_host(vhost); + ibmvfc_init_host(vhost, 0); else dev_err(vhost->dev, "Unable to send init rsp. rc=%ld\n", rc); break; case IBMVFC_CRQ_INIT_COMPLETE: dev_info(vhost->dev, "Partner initialization complete\n"); - ibmvfc_init_host(vhost); + ibmvfc_init_host(vhost, 0); break; default: dev_err(vhost->dev, "Unknown crq message type: %d\n", crq->format); @@ -3358,8 +3364,6 @@ static void ibmvfc_npiv_login(struct ibmvfc_host *vhost) mad->buffer.va = vhost->login_buf_dma; mad->buffer.len = sizeof(*vhost->login_buf); - memset(vhost->async_crq.msgs, 0, PAGE_SIZE); - vhost->async_crq.cur = 0; ibmvfc_set_host_action(vhost, IBMVFC_HOST_ACTION_INIT_WAIT); if (!ibmvfc_send_event(evt, vhost, default_timeout)) -- GitLab From 2bac406df52100aec42e230a2cc2986d34e86218 Mon Sep 17 00:00:00 2001 From: Brian King Date: Fri, 15 Aug 2008 10:59:26 -0500 Subject: [PATCH 501/750] [SCSI] ibmvfc: Sanitize response lengths Sanitize the response lengths in order to prevent possible oopses in the command response path. Signed-off-by: Brian King Signed-off-by: James Bottomley --- drivers/scsi/ibmvscsi/ibmvfc.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/scsi/ibmvscsi/ibmvfc.c b/drivers/scsi/ibmvscsi/ibmvfc.c index 58f8c9e39ae..6ecc0ddd444 100644 --- a/drivers/scsi/ibmvscsi/ibmvfc.c +++ b/drivers/scsi/ibmvscsi/ibmvfc.c @@ -1457,8 +1457,8 @@ static void ibmvfc_scsi_done(struct ibmvfc_event *evt) struct ibmvfc_cmd *vfc_cmd = &evt->xfer_iu->cmd; struct ibmvfc_fcp_rsp *rsp = &vfc_cmd->rsp; struct scsi_cmnd *cmnd = evt->cmnd; - int rsp_len = 0; - int sense_len = rsp->fcp_sense_len; + u32 rsp_len = 0; + u32 sense_len = rsp->fcp_sense_len; if (cmnd) { if (vfc_cmd->response_flags & IBMVFC_ADAPTER_RESID_VALID) @@ -1475,7 +1475,7 @@ static void ibmvfc_scsi_done(struct ibmvfc_event *evt) rsp_len = rsp->fcp_rsp_len; if ((sense_len + rsp_len) > SCSI_SENSE_BUFFERSIZE) sense_len = SCSI_SENSE_BUFFERSIZE - rsp_len; - if ((rsp->flags & FCP_SNS_LEN_VALID) && rsp->fcp_sense_len) + if ((rsp->flags & FCP_SNS_LEN_VALID) && rsp->fcp_sense_len && rsp_len <= 8) memcpy(cmnd->sense_buffer, rsp->data.sense + rsp_len, sense_len); ibmvfc_log_error(evt); -- GitLab From 3e3399467d4c4aefe6a24225b5b277cf7d6e58a7 Mon Sep 17 00:00:00 2001 From: Brian King Date: Fri, 15 Aug 2008 10:59:27 -0500 Subject: [PATCH 502/750] [SCSI] ibmvfc: Add details to async event log When logging async events, also print the payload in addition to the event received. Signed-off-by: Brian King Signed-off-by: James Bottomley --- drivers/scsi/ibmvscsi/ibmvfc.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/scsi/ibmvscsi/ibmvfc.c b/drivers/scsi/ibmvscsi/ibmvfc.c index 6ecc0ddd444..4e0b7c8eb32 100644 --- a/drivers/scsi/ibmvscsi/ibmvfc.c +++ b/drivers/scsi/ibmvscsi/ibmvfc.c @@ -2084,7 +2084,8 @@ static void ibmvfc_handle_async(struct ibmvfc_async_crq *crq, { const char *desc = ibmvfc_get_ae_desc(crq->event); - ibmvfc_log(vhost, 3, "%s event received\n", desc); + ibmvfc_log(vhost, 3, "%s event received. scsi_id: %lx, wwpn: %lx," + " node_name: %lx\n", desc, crq->scsi_id, crq->wwpn, crq->node_name); switch (crq->event) { case IBMVFC_AE_LINK_UP: -- GitLab From 7d0e367ab3f3ad345bd3e121c4c5f511e8b274fa Mon Sep 17 00:00:00 2001 From: Brian King Date: Fri, 15 Aug 2008 10:59:28 -0500 Subject: [PATCH 503/750] [SCSI] ibmvfc: Driver version 1.0.2 Bump driver version to 1.0.2. Signed-off-by: Brian King Signed-off-by: James Bottomley --- drivers/scsi/ibmvscsi/ibmvfc.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/scsi/ibmvscsi/ibmvfc.h b/drivers/scsi/ibmvscsi/ibmvfc.h index 4bf6e374f07..fb3177ab669 100644 --- a/drivers/scsi/ibmvscsi/ibmvfc.h +++ b/drivers/scsi/ibmvscsi/ibmvfc.h @@ -29,8 +29,8 @@ #include "viosrp.h" #define IBMVFC_NAME "ibmvfc" -#define IBMVFC_DRIVER_VERSION "1.0.1" -#define IBMVFC_DRIVER_DATE "(July 11, 2008)" +#define IBMVFC_DRIVER_VERSION "1.0.2" +#define IBMVFC_DRIVER_DATE "(August 14, 2008)" #define IBMVFC_DEFAULT_TIMEOUT 15 #define IBMVFC_INIT_TIMEOUT 30 -- GitLab From 66bfa2f03191aec2e2958414b1dfb80a56637133 Mon Sep 17 00:00:00 2001 From: Adrian Bunk Date: Sun, 10 Aug 2008 15:25:55 +0100 Subject: [PATCH 504/750] [ARM] 5191/1: ARM: remove CVS keywords This patch removes CVS keywords that weren't updated for a long time. Signed-off-by: Adrian Bunk Signed-off-by: Russell King --- arch/arm/include/asm/mtd-xip.h | 2 -- arch/arm/mach-integrator/cpu.c | 2 -- arch/arm/mach-integrator/include/mach/platform.h | 2 -- arch/arm/mach-lh7a40x/include/mach/ssp.h | 1 - arch/arm/mach-lh7a40x/lcd-panel.h | 1 - arch/arm/mach-pxa/include/mach/mtd-xip.h | 2 -- arch/arm/mach-s3c2410/include/mach/regs-clock.h | 2 +- arch/arm/mach-s3c2410/include/mach/regs-gpio.h | 2 +- arch/arm/mach-s3c2410/include/mach/regs-irq.h | 2 +- arch/arm/mach-s3c2410/include/mach/regs-lcd.h | 2 +- arch/arm/mach-s3c2410/include/mach/regs-mem.h | 2 +- arch/arm/mach-s3c2410/mach-smdk2410.c | 1 - arch/arm/mach-sa1100/cpu-sa1110.c | 2 -- arch/arm/mach-sa1100/include/mach/mtd-xip.h | 2 -- include/asm-arm/plat-s3c/regs-nand.h | 2 +- include/asm-arm/plat-s3c/regs-timer.h | 2 +- include/asm-arm/plat-s3c/regs-watchdog.h | 2 +- 17 files changed, 8 insertions(+), 23 deletions(-) diff --git a/arch/arm/include/asm/mtd-xip.h b/arch/arm/include/asm/mtd-xip.h index 4225372a26f..d8fbe2d9b8b 100644 --- a/arch/arm/include/asm/mtd-xip.h +++ b/arch/arm/include/asm/mtd-xip.h @@ -10,8 +10,6 @@ * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. - * - * $Id: xip.h,v 1.2 2004/12/01 15:49:10 nico Exp $ */ #ifndef __ARM_MTD_XIP_H__ diff --git a/arch/arm/mach-integrator/cpu.c b/arch/arm/mach-integrator/cpu.c index ce5ea7c2667..7c49d55e6b2 100644 --- a/arch/arm/mach-integrator/cpu.c +++ b/arch/arm/mach-integrator/cpu.c @@ -3,8 +3,6 @@ * * Copyright (C) 2001-2002 Deep Blue Solutions Ltd. * - * $Id: cpu.c,v 1.6 2002/07/18 13:58:51 rmk Exp $ - * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. diff --git a/arch/arm/mach-integrator/include/mach/platform.h b/arch/arm/mach-integrator/include/mach/platform.h index 83c4c1ceb41..028b87839c0 100644 --- a/arch/arm/mach-integrator/include/mach/platform.h +++ b/arch/arm/mach-integrator/include/mach/platform.h @@ -26,8 +26,6 @@ * NOTE: This is a multi-hosted header file for use with uHAL and * supported debuggers. * - * $Id: platform.s,v 1.32 2000/02/18 10:51:39 asims Exp $ - * * ***********************************************************************/ #ifndef __address_h diff --git a/arch/arm/mach-lh7a40x/include/mach/ssp.h b/arch/arm/mach-lh7a40x/include/mach/ssp.h index 132b1c4d5ce..509916182e3 100644 --- a/arch/arm/mach-lh7a40x/include/mach/ssp.h +++ b/arch/arm/mach-lh7a40x/include/mach/ssp.h @@ -1,5 +1,4 @@ /* ssp.h - $Id$ written by Marc Singer 6 Dec 2004 diff --git a/arch/arm/mach-lh7a40x/lcd-panel.h b/arch/arm/mach-lh7a40x/lcd-panel.h index df6e38ed425..a7f5027b2f7 100644 --- a/arch/arm/mach-lh7a40x/lcd-panel.h +++ b/arch/arm/mach-lh7a40x/lcd-panel.h @@ -1,5 +1,4 @@ /* lcd-panel.h - $Id$ written by Marc Singer 18 Jul 2005 diff --git a/arch/arm/mach-pxa/include/mach/mtd-xip.h b/arch/arm/mach-pxa/include/mach/mtd-xip.h index 351f32f13ce..4d452fcb150 100644 --- a/arch/arm/mach-pxa/include/mach/mtd-xip.h +++ b/arch/arm/mach-pxa/include/mach/mtd-xip.h @@ -10,8 +10,6 @@ * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. - * - * $Id: xip.h,v 1.2 2004/12/01 15:49:10 nico Exp $ */ #ifndef __ARCH_PXA_MTD_XIP_H__ diff --git a/arch/arm/mach-s3c2410/include/mach/regs-clock.h b/arch/arm/mach-s3c2410/include/mach/regs-clock.h index d583688458a..b3f90aa7807 100644 --- a/arch/arm/mach-s3c2410/include/mach/regs-clock.h +++ b/arch/arm/mach-s3c2410/include/mach/regs-clock.h @@ -11,7 +11,7 @@ */ #ifndef __ASM_ARM_REGS_CLOCK -#define __ASM_ARM_REGS_CLOCK "$Id: clock.h,v 1.4 2003/04/30 14:50:51 ben Exp $" +#define __ASM_ARM_REGS_CLOCK #define S3C2410_CLKREG(x) ((x) + S3C24XX_VA_CLKPWR) diff --git a/arch/arm/mach-s3c2410/include/mach/regs-gpio.h b/arch/arm/mach-s3c2410/include/mach/regs-gpio.h index 30bec027f5f..528080ceac4 100644 --- a/arch/arm/mach-s3c2410/include/mach/regs-gpio.h +++ b/arch/arm/mach-s3c2410/include/mach/regs-gpio.h @@ -12,7 +12,7 @@ #ifndef __ASM_ARCH_REGS_GPIO_H -#define __ASM_ARCH_REGS_GPIO_H "$Id: gpio.h,v 1.5 2003/05/19 12:51:08 ben Exp $" +#define __ASM_ARCH_REGS_GPIO_H #define S3C2410_GPIONO(bank,offset) ((bank) + (offset)) diff --git a/arch/arm/mach-s3c2410/include/mach/regs-irq.h b/arch/arm/mach-s3c2410/include/mach/regs-irq.h index b057c06d167..de86ee8812b 100644 --- a/arch/arm/mach-s3c2410/include/mach/regs-irq.h +++ b/arch/arm/mach-s3c2410/include/mach/regs-irq.h @@ -10,7 +10,7 @@ #ifndef ___ASM_ARCH_REGS_IRQ_H -#define ___ASM_ARCH_REGS_IRQ_H "$Id: irq.h,v 1.3 2003/03/25 21:29:06 ben Exp $" +#define ___ASM_ARCH_REGS_IRQ_H /* interrupt controller */ diff --git a/arch/arm/mach-s3c2410/include/mach/regs-lcd.h b/arch/arm/mach-s3c2410/include/mach/regs-lcd.h index 893b8742f95..ee8f040aff5 100644 --- a/arch/arm/mach-s3c2410/include/mach/regs-lcd.h +++ b/arch/arm/mach-s3c2410/include/mach/regs-lcd.h @@ -10,7 +10,7 @@ #ifndef ___ASM_ARCH_REGS_LCD_H -#define ___ASM_ARCH_REGS_LCD_H "$Id: lcd.h,v 1.3 2003/06/26 13:25:06 ben Exp $" +#define ___ASM_ARCH_REGS_LCD_H #define S3C2410_LCDREG(x) (x) diff --git a/arch/arm/mach-s3c2410/include/mach/regs-mem.h b/arch/arm/mach-s3c2410/include/mach/regs-mem.h index f9926abd5cd..57759804e2f 100644 --- a/arch/arm/mach-s3c2410/include/mach/regs-mem.h +++ b/arch/arm/mach-s3c2410/include/mach/regs-mem.h @@ -11,7 +11,7 @@ */ #ifndef __ASM_ARM_MEMREGS_H -#define __ASM_ARM_MEMREGS_H "$Id: regs.h,v 1.8 2003/05/01 15:55:41 ben Exp $" +#define __ASM_ARM_MEMREGS_H #ifndef S3C2410_MEMREG #define S3C2410_MEMREG(x) (S3C24XX_VA_MEMCTRL + (x)) diff --git a/arch/arm/mach-s3c2410/mach-smdk2410.c b/arch/arm/mach-s3c2410/mach-smdk2410.c index c9040080727..b88939d7228 100644 --- a/arch/arm/mach-s3c2410/mach-smdk2410.c +++ b/arch/arm/mach-s3c2410/mach-smdk2410.c @@ -5,7 +5,6 @@ * Copyright (C) 2004 by FS Forth-Systeme GmbH * All rights reserved. * - * $Id: mach-smdk2410.c,v 1.1 2004/05/11 14:15:38 mpietrek Exp $ * @Author: Jonas Dietsche * * This program is free software; you can redistribute it and/or diff --git a/arch/arm/mach-sa1100/cpu-sa1110.c b/arch/arm/mach-sa1100/cpu-sa1110.c index 39d38c80173..029dbfbbafc 100644 --- a/arch/arm/mach-sa1100/cpu-sa1110.c +++ b/arch/arm/mach-sa1100/cpu-sa1110.c @@ -3,8 +3,6 @@ * * Copyright (C) 2001 Russell King * - * $Id: cpu-sa1110.c,v 1.9 2002/07/06 16:53:18 rmk Exp $ - * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. diff --git a/arch/arm/mach-sa1100/include/mach/mtd-xip.h b/arch/arm/mach-sa1100/include/mach/mtd-xip.h index 80cfdac2b94..eaa09e86ad1 100644 --- a/arch/arm/mach-sa1100/include/mach/mtd-xip.h +++ b/arch/arm/mach-sa1100/include/mach/mtd-xip.h @@ -10,8 +10,6 @@ * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. - * - * $Id: xip.h,v 1.2 2004/12/01 15:49:10 nico Exp $ */ #ifndef __ARCH_SA1100_MTD_XIP_H__ diff --git a/include/asm-arm/plat-s3c/regs-nand.h b/include/asm-arm/plat-s3c/regs-nand.h index 09f0b5503f5..b2caa4bca27 100644 --- a/include/asm-arm/plat-s3c/regs-nand.h +++ b/include/asm-arm/plat-s3c/regs-nand.h @@ -11,7 +11,7 @@ */ #ifndef __ASM_ARM_REGS_NAND -#define __ASM_ARM_REGS_NAND "$Id: nand.h,v 1.3 2003/12/09 11:36:29 ben Exp $" +#define __ASM_ARM_REGS_NAND #define S3C2410_NFREG(x) (x) diff --git a/include/asm-arm/plat-s3c/regs-timer.h b/include/asm-arm/plat-s3c/regs-timer.h index b4366ea3967..cc0eedd53e3 100644 --- a/include/asm-arm/plat-s3c/regs-timer.h +++ b/include/asm-arm/plat-s3c/regs-timer.h @@ -12,7 +12,7 @@ #ifndef __ASM_ARCH_REGS_TIMER_H -#define __ASM_ARCH_REGS_TIMER_H "$Id: timer.h,v 1.4 2003/05/06 19:30:50 ben Exp $" +#define __ASM_ARCH_REGS_TIMER_H #define S3C_TIMERREG(x) (S3C_VA_TIMER + (x)) #define S3C_TIMERREG2(tmr,reg) S3C_TIMERREG((reg)+0x0c+((tmr)*0x0c)) diff --git a/include/asm-arm/plat-s3c/regs-watchdog.h b/include/asm-arm/plat-s3c/regs-watchdog.h index 1229f076c0a..4938492470f 100644 --- a/include/asm-arm/plat-s3c/regs-watchdog.h +++ b/include/asm-arm/plat-s3c/regs-watchdog.h @@ -12,7 +12,7 @@ #ifndef __ASM_ARCH_REGS_WATCHDOG_H -#define __ASM_ARCH_REGS_WATCHDOG_H "$Id: watchdog.h,v 1.2 2003/04/29 13:31:09 ben Exp $" +#define __ASM_ARCH_REGS_WATCHDOG_H #define S3C_WDOGREG(x) ((x) + S3C_VA_WATCHDOG) -- GitLab From 605d9288b3e8a3d15e6f36185c2fc737b6979572 Mon Sep 17 00:00:00 2001 From: Hugh Dickins Date: Sat, 16 Aug 2008 11:07:21 +0100 Subject: [PATCH 505/750] mm: VM_flags comment fixes Try to comment away a little of the confusion between mm's vm_area_struct vm_flags and vmalloc's vm_struct flags: based on an idea by Ulrich Drepper. Signed-off-by: Hugh Dickins Signed-off-by: Linus Torvalds --- include/linux/mm.h | 2 +- include/linux/mm_types.h | 2 +- include/linux/vmalloc.h | 4 ++-- 3 files changed, 4 insertions(+), 4 deletions(-) diff --git a/include/linux/mm.h b/include/linux/mm.h index fa651609b65..72a15dc26bb 100644 --- a/include/linux/mm.h +++ b/include/linux/mm.h @@ -73,7 +73,7 @@ extern unsigned int kobjsize(const void *objp); #endif /* - * vm_flags.. + * vm_flags in vm_area_struct, see mm_types.h. */ #define VM_READ 0x00000001 /* currently active flags */ #define VM_WRITE 0x00000002 diff --git a/include/linux/mm_types.h b/include/linux/mm_types.h index 386edbe2cb4..bf334138c7c 100644 --- a/include/linux/mm_types.h +++ b/include/linux/mm_types.h @@ -113,7 +113,7 @@ struct vm_area_struct { struct vm_area_struct *vm_next; pgprot_t vm_page_prot; /* Access permissions of this VMA. */ - unsigned long vm_flags; /* Flags, listed below. */ + unsigned long vm_flags; /* Flags, see mm.h. */ struct rb_node vm_rb; diff --git a/include/linux/vmalloc.h b/include/linux/vmalloc.h index 364789aae9f..328eb402272 100644 --- a/include/linux/vmalloc.h +++ b/include/linux/vmalloc.h @@ -4,9 +4,9 @@ #include #include /* pgprot_t */ -struct vm_area_struct; +struct vm_area_struct; /* vma defining user mapping in mm_types.h */ -/* bits in vm_struct->flags */ +/* bits in flags of vmalloc's vm_struct below */ #define VM_IOREMAP 0x00000001 /* ioremap() and friends */ #define VM_ALLOC 0x00000002 /* vmalloc() */ #define VM_MAP 0x00000004 /* vmap()ed pages */ -- GitLab From 5e6b83ed8c00f2e2ae5b2413c5907bed735b600d Mon Sep 17 00:00:00 2001 From: David Woodhouse Date: Sat, 16 Aug 2008 11:55:04 +0100 Subject: [PATCH 506/750] Fix header export of videodev2.h, ivtv.h, ivtvfb.h The exported copy of videodev2.h contains this line: #define #include This is because for some reason it defines __user for itself -- despite the fact that we remove all instances of __user when exporting headers. _All_ pointers in userspace are user pointers. Fix it by removing the unnecessary '#define __user' from the file. The new headers ivtv.h and ivtvfb.h would have the same problem... if whoever put them there had actually remembered to add them to the Kbuild file while he was at it. Fix those too, and export them as was presumably intended. Note that includes of are also stripped by the header export process, so those don't need to be conditional. Signed-off-by: David Woodhouse Signed-off-by: Mauro Carvalho Chehab Acked-by: Hans Verkuil Signed-off-by: Linus Torvalds --- include/linux/Kbuild | 2 ++ include/linux/ivtv.h | 6 +----- include/linux/ivtvfb.h | 6 +----- include/linux/videodev2.h | 4 ++-- 4 files changed, 6 insertions(+), 12 deletions(-) diff --git a/include/linux/Kbuild b/include/linux/Kbuild index 327f60658d9..7d970678f94 100644 --- a/include/linux/Kbuild +++ b/include/linux/Kbuild @@ -250,6 +250,8 @@ unifdef-y += isdn.h unifdef-y += isdnif.h unifdef-y += isdn_divertif.h unifdef-y += isdn_ppp.h +unifdef-y += ivtv.h +unifdef-y += ivtvfb.h unifdef-y += joystick.h unifdef-y += kdev_t.h unifdef-y += kd.h diff --git a/include/linux/ivtv.h b/include/linux/ivtv.h index 794b8daa937..17ca64b5a66 100644 --- a/include/linux/ivtv.h +++ b/include/linux/ivtv.h @@ -21,11 +21,7 @@ #ifndef __LINUX_IVTV_H__ #define __LINUX_IVTV_H__ -#ifdef __KERNEL__ -#include /* need __user */ -#else -#define __user -#endif +#include #include /* ivtv knows several distinct output modes: MPEG streaming, diff --git a/include/linux/ivtvfb.h b/include/linux/ivtvfb.h index e980ba62ddc..e20af47b59a 100644 --- a/include/linux/ivtvfb.h +++ b/include/linux/ivtvfb.h @@ -21,11 +21,7 @@ #ifndef __LINUX_IVTVFB_H__ #define __LINUX_IVTVFB_H__ -#ifdef __KERNEL__ -#include /* need __user */ -#else -#define __user -#endif +#include #include /* Framebuffer external API */ diff --git a/include/linux/videodev2.h b/include/linux/videodev2.h index e466bd54a50..e65a6bed4e3 100644 --- a/include/linux/videodev2.h +++ b/include/linux/videodev2.h @@ -55,13 +55,13 @@ */ #ifndef __LINUX_VIDEODEV2_H #define __LINUX_VIDEODEV2_H + #ifdef __KERNEL__ #include /* need struct timeval */ -#include /* need __user */ #else -#define __user #include #endif +#include #include #include -- GitLab From 9e94cd325bb8ed8abe13f29b64fb54c1dec633a8 Mon Sep 17 00:00:00 2001 From: Andi Kleen Date: Sat, 16 Aug 2008 07:53:05 +0200 Subject: [PATCH 507/750] Move sysctl check into debugging section and don't make it default y I noticed that sysctl_check.o was the largest object file in a allnoconfig build in kernel/*. 36243 0 0 36243 8d93 kernel/sysctl_check.o This is because it was default y and && EMBEDDED. But I don't really see a need for a non kernel developer to have their sysctls checked all the time. So move the Kconfig into the kernel debugging section and also drop the default y and the EMBEDDED check. Signed-off-by: Andi Kleen Signed-off-by: Linus Torvalds --- init/Kconfig | 11 ----------- lib/Kconfig.debug | 8 ++++++++ 2 files changed, 8 insertions(+), 11 deletions(-) diff --git a/init/Kconfig b/init/Kconfig index b678803decc..c11da38837e 100644 --- a/init/Kconfig +++ b/init/Kconfig @@ -558,17 +558,6 @@ config SYSCTL_SYSCALL If unsure say Y here. -config SYSCTL_SYSCALL_CHECK - bool "Sysctl checks" if EMBEDDED - depends on SYSCTL_SYSCALL - default y - ---help--- - sys_sysctl uses binary paths that have been found challenging - to properly maintain and use. This enables checks that help - you to keep things correct. - - If unsure say Y here. - config KALLSYMS bool "Load all symbols for debugging/ksymoops" if EMBEDDED default y diff --git a/lib/Kconfig.debug b/lib/Kconfig.debug index 800ac848554..8b5a7d304a5 100644 --- a/lib/Kconfig.debug +++ b/lib/Kconfig.debug @@ -693,6 +693,14 @@ config LATENCYTOP Enable this option if you want to use the LatencyTOP tool to find out which userspace is blocking on what kernel operations. +config SYSCTL_SYSCALL_CHECK + bool "Sysctl checks" + depends on SYSCTL_SYSCALL + ---help--- + sys_sysctl uses binary paths that have been found challenging + to properly maintain and use. This enables checks that help + you to keep things correct. + source kernel/trace/Kconfig config PROVIDE_OHCI1394_DMA_INIT -- GitLab From b09c3e3f1710b554348c98e78fbf4a661918779a Mon Sep 17 00:00:00 2001 From: Huang Weiyi Date: Sun, 17 Aug 2008 07:51:05 +0800 Subject: [PATCH 508/750] removed unused #include The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION. drivers/char/pcmcia/ipwireless/tty.c drivers/char/synclink_gt.c drivers/char/xilinx_hwicap/xilinx_hwicap.c This patch removes the said #include . Signed-off-by: Huang Weiyi Signed-off-by: Linus Torvalds --- drivers/char/pcmcia/ipwireless/tty.c | 1 - drivers/char/synclink_gt.c | 1 - drivers/char/xilinx_hwicap/xilinx_hwicap.c | 1 - 3 files changed, 3 deletions(-) diff --git a/drivers/char/pcmcia/ipwireless/tty.c b/drivers/char/pcmcia/ipwireless/tty.c index b1414507997..3a23e7694d5 100644 --- a/drivers/char/pcmcia/ipwireless/tty.c +++ b/drivers/char/pcmcia/ipwireless/tty.c @@ -29,7 +29,6 @@ #include #include #include -#include #include "tty.h" #include "network.h" diff --git a/drivers/char/synclink_gt.c b/drivers/char/synclink_gt.c index 509c89ac5bd..08911ed6649 100644 --- a/drivers/char/synclink_gt.c +++ b/drivers/char/synclink_gt.c @@ -47,7 +47,6 @@ #include -#include #include #include #include diff --git a/drivers/char/xilinx_hwicap/xilinx_hwicap.c b/drivers/char/xilinx_hwicap/xilinx_hwicap.c index 8bfee5fb722..278c9857bcf 100644 --- a/drivers/char/xilinx_hwicap/xilinx_hwicap.c +++ b/drivers/char/xilinx_hwicap/xilinx_hwicap.c @@ -74,7 +74,6 @@ * currently programmed in the FPGA. */ -#include #include #include #include -- GitLab From f511b01c8e747b80635c8b2acd61431abcab4b29 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Fri, 15 Aug 2008 16:46:42 +0200 Subject: [PATCH 509/750] ALSA: hda - Fix capture source widgets on ALC codecs On some Realtek codecs like ALC882 or ALC883, the capture source is no mux but sum widget. We have to initialize all channels properly for this type, otherwise noises may come in from the unused route. The patch assures to mute unused routes, and unmute the currently selected route. Signed-off-by: Takashi Iwai Tested-by: Daniel J Blueman --- sound/pci/hda/patch_realtek.c | 45 +++++++++++++++++++++++++++++++++++ 1 file changed, 45 insertions(+) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index add4e87e0b2..b80e725432f 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -6437,6 +6437,39 @@ static void alc882_auto_init_analog_input(struct hda_codec *codec) } } +static void alc882_auto_init_input_src(struct hda_codec *codec) +{ + struct alc_spec *spec = codec->spec; + const struct hda_input_mux *imux = spec->input_mux; + int c; + + for (c = 0; c < spec->num_adc_nids; c++) { + hda_nid_t conn_list[HDA_MAX_NUM_INPUTS]; + hda_nid_t nid = spec->capsrc_nids[c]; + int conns, mute, idx, item; + + conns = snd_hda_get_connections(codec, nid, conn_list, + ARRAY_SIZE(conn_list)); + if (conns < 0) + continue; + for (idx = 0; idx < conns; idx++) { + /* if the current connection is the selected one, + * unmute it as default - otherwise mute it + */ + mute = AMP_IN_MUTE(idx); + for (item = 0; item < imux->num_items; item++) { + if (imux->items[item].index == idx) { + if (spec->cur_mux[c] == item) + mute = AMP_IN_UNMUTE(idx); + break; + } + } + snd_hda_codec_write(codec, nid, 0, + AC_VERB_SET_AMP_GAIN_MUTE, mute); + } + } +} + /* add mic boosts if needed */ static int alc_auto_add_mic_boost(struct hda_codec *codec) { @@ -6491,6 +6524,7 @@ static void alc882_auto_init(struct hda_codec *codec) alc882_auto_init_multi_out(codec); alc882_auto_init_hp_out(codec); alc882_auto_init_analog_input(codec); + alc882_auto_init_input_src(codec); if (spec->unsol_event) alc_sku_automute(codec); } @@ -8285,6 +8319,8 @@ static void alc883_auto_init_analog_input(struct hda_codec *codec) } } +#define alc883_auto_init_input_src alc882_auto_init_input_src + /* almost identical with ALC880 parser... */ static int alc883_parse_auto_config(struct hda_codec *codec) { @@ -8315,6 +8351,7 @@ static void alc883_auto_init(struct hda_codec *codec) alc883_auto_init_multi_out(codec); alc883_auto_init_hp_out(codec); alc883_auto_init_analog_input(codec); + alc883_auto_init_input_src(codec); if (spec->unsol_event) alc_sku_automute(codec); } @@ -9663,6 +9700,7 @@ static int alc262_parse_auto_config(struct hda_codec *codec) #define alc262_auto_init_multi_out alc882_auto_init_multi_out #define alc262_auto_init_hp_out alc882_auto_init_hp_out #define alc262_auto_init_analog_input alc882_auto_init_analog_input +#define alc262_auto_init_input_src alc882_auto_init_input_src /* init callback for auto-configuration model -- overriding the default init */ @@ -9672,6 +9710,7 @@ static void alc262_auto_init(struct hda_codec *codec) alc262_auto_init_multi_out(codec); alc262_auto_init_hp_out(codec); alc262_auto_init_analog_input(codec); + alc262_auto_init_input_src(codec); if (spec->unsol_event) alc_sku_automute(codec); } @@ -13330,6 +13369,8 @@ static void alc861vd_auto_init_analog_input(struct hda_codec *codec) } } +#define alc861vd_auto_init_input_src alc882_auto_init_input_src + #define alc861vd_idx_to_mixer_vol(nid) ((nid) + 0x02) #define alc861vd_idx_to_mixer_switch(nid) ((nid) + 0x0c) @@ -13512,6 +13553,7 @@ static void alc861vd_auto_init(struct hda_codec *codec) alc861vd_auto_init_multi_out(codec); alc861vd_auto_init_hp_out(codec); alc861vd_auto_init_analog_input(codec); + alc861vd_auto_init_input_src(codec); if (spec->unsol_event) alc_sku_automute(codec); } @@ -14677,6 +14719,8 @@ static void alc662_auto_init_analog_input(struct hda_codec *codec) } } +#define alc662_auto_init_input_src alc882_auto_init_input_src + static int alc662_parse_auto_config(struct hda_codec *codec) { struct alc_spec *spec = codec->spec; @@ -14733,6 +14777,7 @@ static void alc662_auto_init(struct hda_codec *codec) alc662_auto_init_multi_out(codec); alc662_auto_init_hp_out(codec); alc662_auto_init_analog_input(codec); + alc662_auto_init_input_src(codec); if (spec->unsol_event) alc_sku_automute(codec); } -- GitLab From 5e186b57e7ede86aeb9db30e66315bde4e8b1815 Mon Sep 17 00:00:00 2001 From: Alexander Beregalov Date: Sun, 17 Aug 2008 05:34:20 +0400 Subject: [PATCH 510/750] security.h: fix build failure security.h: fix build failure include/linux/security.h: In function 'security_ptrace_traceme': include/linux/security.h:1760: error: 'parent' undeclared (first use in this function) Signed-off-by: Alexander Beregalov Tested-by: Ingo Molnar Signed-off-by: James Morris --- include/linux/security.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/linux/security.h b/include/linux/security.h index 2ee5ecfb239..80c4d002864 100644 --- a/include/linux/security.h +++ b/include/linux/security.h @@ -1755,7 +1755,7 @@ static inline int security_ptrace_may_access(struct task_struct *child, return cap_ptrace_may_access(child, mode); } -static inline int security_ptrace_traceme(struct task_struct *child) +static inline int security_ptrace_traceme(struct task_struct *parent) { return cap_ptrace_traceme(parent); } -- GitLab From 5d304400a9a867a7ce545f3ae6d95d92b62570f7 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Fri, 8 Aug 2008 10:55:41 +0100 Subject: [PATCH 511/750] s3cmci: fix sparse errors from non-exported functions Fix the following sparse errors by making the functions static and fixing the check for host->base. 598:6: warning: symbol 's3cmci_dma_done_callback' was not declared. Should it be static? 744:6: warning: symbol 's3cmci_dma_setup' was not declared. Should it be static? 1209:20: warning: Using plain integer as NULL pointer Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- drivers/mmc/host/s3cmci.c | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-) diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index 7c994e1ae27..6afa4c04854 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -595,8 +595,9 @@ static irqreturn_t s3cmci_irq_cd(int irq, void *dev_id) return IRQ_HANDLED; } -void s3cmci_dma_done_callback(struct s3c2410_dma_chan *dma_ch, void *buf_id, - int size, enum s3c2410_dma_buffresult result) +static void s3cmci_dma_done_callback(struct s3c2410_dma_chan *dma_ch, + void *buf_id, int size, + enum s3c2410_dma_buffresult result) { struct s3cmci_host *host = buf_id; unsigned long iflags; @@ -740,8 +741,8 @@ request_done: mmc_request_done(host->mmc, mrq); } - -void s3cmci_dma_setup(struct s3cmci_host *host, enum s3c2410_dmasrc source) +static void s3cmci_dma_setup(struct s3cmci_host *host, + enum s3c2410_dmasrc source) { static enum s3c2410_dmasrc last_source = -1; static int setup_ok; @@ -1206,7 +1207,7 @@ static int __devinit s3cmci_probe(struct platform_device *pdev, int is2440) } host->base = ioremap(host->mem->start, RESSIZE(host->mem)); - if (host->base == 0) { + if (!host->base) { dev_err(&pdev->dev, "failed to ioremap() io memory region.\n"); ret = -EINVAL; goto probe_free_mem_region; -- GitLab From 87dd98037d2309efbbd5e769efb23d845c37dac7 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Tue, 12 Aug 2008 09:24:50 +0100 Subject: [PATCH 512/750] s3cmci: attach get_cd host ops Attach the routine to get_cd to allow the MMC core to find out whether there is a card present or not without the tedious process of trying to send commands to the card or not. Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- drivers/mmc/host/s3cmci.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index 6afa4c04854..ae16d845d74 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -1004,8 +1004,9 @@ static void s3cmci_send_request(struct mmc_host *mmc) enable_irq(host->irq); } -static int s3cmci_card_present(struct s3cmci_host *host) +static int s3cmci_card_present(struct mmc_host *mmc) { + struct s3cmci_host *host = mmc_priv(mmc); struct s3c24xx_mci_pdata *pdata = host->pdata; int ret; @@ -1024,7 +1025,7 @@ static void s3cmci_request(struct mmc_host *mmc, struct mmc_request *mrq) host->cmd_is_stop = 0; host->mrq = mrq; - if (s3cmci_card_present(host) == 0) { + if (s3cmci_card_present(mmc) == 0) { dbg(host, dbg_err, "%s: no medium present\n", __func__); host->mrq->cmd->error = -ENOMEDIUM; mmc_request_done(mmc, mrq); @@ -1139,6 +1140,7 @@ static struct mmc_host_ops s3cmci_ops = { .request = s3cmci_request, .set_ios = s3cmci_set_ios, .get_ro = s3cmci_get_ro, + .get_cd = s3cmci_card_present, }; static struct s3c24xx_mci_pdata s3cmci_def_pdata = { -- GitLab From fe7f962505892c7894c473cd78ade87767689c8d Mon Sep 17 00:00:00 2001 From: Huang Weiyi Date: Sun, 17 Aug 2008 07:51:10 +0800 Subject: [PATCH 513/750] sdricoh_cs: removed unused #include The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION. drivers/mmc/host/sdricoh_cs.c This patch removes the said #include . Signed-off-by: Huang Weiyi Signed-off-by: Pierre Ossman --- drivers/mmc/host/sdricoh_cs.c | 1 - 1 file changed, 1 deletion(-) diff --git a/drivers/mmc/host/sdricoh_cs.c b/drivers/mmc/host/sdricoh_cs.c index f99e9f72162..1df44d966bd 100644 --- a/drivers/mmc/host/sdricoh_cs.c +++ b/drivers/mmc/host/sdricoh_cs.c @@ -29,7 +29,6 @@ #include #include #include -#include #include #include -- GitLab From 3fadc52b2c9171b138b93f4a0121ceba67241b3b Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Tue, 12 Aug 2008 17:03:26 +1000 Subject: [PATCH 514/750] powerpc: Fix loss of vdso on fork on 32-bit When we fork, init_new_context() improperly resets the vdso_base of the new context to 0. That means that the new process loses access to the vdso for signal trampolines. The initialization should be unnecessary anyway as the context on a fresh mm should be 0 in the first place and binfmt_elf will initialize that value for a newly loaded process. Signed-off-by: Benjamin Herrenschmidt Signed-off-by: Paul Mackerras --- arch/powerpc/include/asm/mmu_context.h | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/powerpc/include/asm/mmu_context.h b/arch/powerpc/include/asm/mmu_context.h index 9102b8bf0ea..6b993ef452f 100644 --- a/arch/powerpc/include/asm/mmu_context.h +++ b/arch/powerpc/include/asm/mmu_context.h @@ -147,7 +147,6 @@ static inline void get_mmu_context(struct mm_struct *mm) static inline int init_new_context(struct task_struct *t, struct mm_struct *mm) { mm->context.id = NO_CONTEXT; - mm->context.vdso_base = 0; return 0; } -- GitLab From 9acd57ca74b12bc8ba8da12c72b19ede2cddcb53 Mon Sep 17 00:00:00 2001 From: Rocky Craig Date: Thu, 14 Aug 2008 23:11:54 +1000 Subject: [PATCH 515/750] powerpc: Fix TLB invalidation on boot on 32-bit The intent of "flush_tlbs" is to invalidate all TLB entries by doing a TLB invalidate instruction for all pages in the address range 0 to 0x00400000. A loop counter is set up at the high value and decremented by page size. However, the loop is only done once as the sense of the conditional branch at the loop end does not match the setup/decrement. This fixes it to do the whole range by correcting the branch condition. Signed-off-by: Rocky Craig Signed-off-by: Paul Mackerras --- arch/powerpc/kernel/head_32.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/powerpc/kernel/head_32.S b/arch/powerpc/kernel/head_32.S index 99ee2f0f0f2..8bb65751929 100644 --- a/arch/powerpc/kernel/head_32.S +++ b/arch/powerpc/kernel/head_32.S @@ -1155,7 +1155,7 @@ flush_tlbs: lis r10, 0x40 1: addic. r10, r10, -0x1000 tlbie r10 - blt 1b + bgt 1b sync blr -- GitLab From 22b8f9ee4a91638a4c8f57e957a91cf49788332a Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Fri, 15 Aug 2008 17:11:31 +1000 Subject: [PATCH 516/750] powerpc: Fix lockdep IRQ tracing bug A small bogon sneaked into the ppc64 lockdep support. A test is branching slightly off causing a clobbered register value to overwrite the irq state under some circumstances. Signed-off-by: Benjamin Herrenschmidt Signed-off-by: Paul Mackerras --- arch/powerpc/include/asm/irqflags.h | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/arch/powerpc/include/asm/irqflags.h b/arch/powerpc/include/asm/irqflags.h index 17ba3a881bf..5f68ecfdf51 100644 --- a/arch/powerpc/include/asm/irqflags.h +++ b/arch/powerpc/include/asm/irqflags.h @@ -20,7 +20,7 @@ #define TRACE_ENABLE_INTS bl .trace_hardirqs_on #define TRACE_DISABLE_INTS bl .trace_hardirqs_off #define TRACE_AND_RESTORE_IRQ_PARTIAL(en,skip) \ - cmpdi en, 0; \ + cmpdi en,0; \ bne 95f; \ stb en,PACASOFTIRQEN(r13); \ bl .trace_hardirqs_off; \ @@ -29,7 +29,8 @@ li en,1; #define TRACE_AND_RESTORE_IRQ(en) \ TRACE_AND_RESTORE_IRQ_PARTIAL(en,96f); \ -96: stb en,PACASOFTIRQEN(r13) + stb en,PACASOFTIRQEN(r13); \ +96: #else #define TRACE_ENABLE_INTS #define TRACE_DISABLE_INTS -- GitLab From 81f14997e8e8a10eb75ca593674d2b0c94129a21 Mon Sep 17 00:00:00 2001 From: Robert Jennings Date: Sat, 16 Aug 2008 05:07:31 +1000 Subject: [PATCH 517/750] powerpc: Make CMO paging space pool ID and page size available During platform setup, save off the primary/secondary paging space pool IDs and the page size. Added accessors in hvcall.h for these variables. This is needed for a subsequent fix. Submitted-by: Robert Jennings Signed-off-by: Paul Mackerras --- arch/powerpc/include/asm/hvcall.h | 22 ++++++++++++++++++++ arch/powerpc/platforms/pseries/setup.c | 28 ++++++++++++++++++-------- 2 files changed, 42 insertions(+), 8 deletions(-) diff --git a/arch/powerpc/include/asm/hvcall.h b/arch/powerpc/include/asm/hvcall.h index fbe2932fa9e..6251a4b10be 100644 --- a/arch/powerpc/include/asm/hvcall.h +++ b/arch/powerpc/include/asm/hvcall.h @@ -291,6 +291,28 @@ struct hvcall_mpp_data { }; int h_get_mpp(struct hvcall_mpp_data *); + +#ifdef CONFIG_PPC_PSERIES +extern int CMO_PrPSP; +extern int CMO_SecPSP; +extern unsigned long CMO_PageSize; + +static inline int cmo_get_primary_psp(void) +{ + return CMO_PrPSP; +} + +static inline int cmo_get_secondary_psp(void) +{ + return CMO_SecPSP; +} + +static inline unsigned long cmo_get_page_size(void) +{ + return CMO_PageSize; +} +#endif /* CONFIG_PPC_PSERIES */ + #endif /* __ASSEMBLY__ */ #endif /* __KERNEL__ */ #endif /* _ASM_POWERPC_HVCALL_H */ diff --git a/arch/powerpc/platforms/pseries/setup.c b/arch/powerpc/platforms/pseries/setup.c index 063a0d2fba3..3ce8a139b85 100644 --- a/arch/powerpc/platforms/pseries/setup.c +++ b/arch/powerpc/platforms/pseries/setup.c @@ -68,6 +68,9 @@ #include "plpar_wrappers.h" #include "pseries.h" +int CMO_PrPSP = -1; +int CMO_SecPSP = -1; +unsigned long CMO_PageSize = (ASM_CONST(1) << IOMMU_PAGE_SHIFT); int fwnmi_active; /* TRUE if an FWNMI handler is present */ @@ -325,8 +328,7 @@ void pSeries_cmo_feature_init(void) { char *ptr, *key, *value, *end; int call_status; - int PrPSP = -1; - int SecPSP = -1; + int page_order = IOMMU_PAGE_SHIFT; pr_debug(" -> fw_cmo_feature_init()\n"); spin_lock(&rtas_data_buf_lock); @@ -365,21 +367,31 @@ void pSeries_cmo_feature_init(void) break; } - if (0 == strcmp(key, "PrPSP")) - PrPSP = simple_strtol(value, NULL, 10); + if (0 == strcmp(key, "CMOPageSize")) + page_order = simple_strtol(value, NULL, 10); + else if (0 == strcmp(key, "PrPSP")) + CMO_PrPSP = simple_strtol(value, NULL, 10); else if (0 == strcmp(key, "SecPSP")) - SecPSP = simple_strtol(value, NULL, 10); + CMO_SecPSP = simple_strtol(value, NULL, 10); value = key = ptr + 1; } ptr++; } - if (PrPSP != -1 || SecPSP != -1) { + /* Page size is returned as the power of 2 of the page size, + * convert to the page size in bytes before returning + */ + CMO_PageSize = 1 << page_order; + pr_debug("CMO_PageSize = %lu\n", CMO_PageSize); + + if (CMO_PrPSP != -1 || CMO_SecPSP != -1) { pr_info("CMO enabled\n"); - pr_debug("CMO enabled, PrPSP=%d, SecPSP=%d\n", PrPSP, SecPSP); + pr_debug("CMO enabled, PrPSP=%d, SecPSP=%d\n", CMO_PrPSP, + CMO_SecPSP); powerpc_firmware_features |= FW_FEATURE_CMO; } else - pr_debug("CMO not enabled, PrPSP=%d, SecPSP=%d\n", PrPSP, SecPSP); + pr_debug("CMO not enabled, PrPSP=%d, SecPSP=%d\n", CMO_PrPSP, + CMO_SecPSP); spin_unlock(&rtas_data_buf_lock); pr_debug(" <- fw_cmo_feature_init()\n"); } -- GitLab From 370e4587d0a6bf80a0c421583fe579a13f3d8773 Mon Sep 17 00:00:00 2001 From: Brian King Date: Sat, 16 Aug 2008 05:09:33 +1000 Subject: [PATCH 518/750] powerpc: Fix CMM page loaning on 64k page kernel with 4k hardware pages If the firmware page size used for collaborative memory overcommit is 4k, but the kernel is using 64k pages, the page loaning is currently broken as it only marks the first 4k page of each 64k page as loaned. This fixes this to iterate through each 4k page and mark them all as loaned/active. Signed-off-by: Brian King Signed-off-by: Robert Jennings Signed-off-by: Paul Mackerras --- .../platforms/pseries/plpar_wrappers.h | 27 +++++++++++++++++-- 1 file changed, 25 insertions(+), 2 deletions(-) diff --git a/arch/powerpc/platforms/pseries/plpar_wrappers.h b/arch/powerpc/platforms/pseries/plpar_wrappers.h index a437267c6bf..d967c1893ab 100644 --- a/arch/powerpc/platforms/pseries/plpar_wrappers.h +++ b/arch/powerpc/platforms/pseries/plpar_wrappers.h @@ -2,6 +2,7 @@ #define _PSERIES_PLPAR_WRAPPERS_H #include +#include static inline long poll_pending(void) { @@ -44,12 +45,34 @@ static inline long register_slb_shadow(unsigned long cpu, unsigned long vpa) static inline long plpar_page_set_loaned(unsigned long vpa) { - return plpar_hcall_norets(H_PAGE_INIT, H_PAGE_SET_LOANED, vpa, 0); + unsigned long cmo_page_sz = cmo_get_page_size(); + long rc = 0; + int i; + + for (i = 0; !rc && i < PAGE_SIZE; i += cmo_page_sz) + rc = plpar_hcall_norets(H_PAGE_INIT, H_PAGE_SET_LOANED, vpa + i, 0); + + for (i -= cmo_page_sz; rc && i != 0; i -= cmo_page_sz) + plpar_hcall_norets(H_PAGE_INIT, H_PAGE_SET_ACTIVE, + vpa + i - cmo_page_sz, 0); + + return rc; } static inline long plpar_page_set_active(unsigned long vpa) { - return plpar_hcall_norets(H_PAGE_INIT, H_PAGE_SET_ACTIVE, vpa, 0); + unsigned long cmo_page_sz = cmo_get_page_size(); + long rc = 0; + int i; + + for (i = 0; !rc && i < PAGE_SIZE; i += cmo_page_sz) + rc = plpar_hcall_norets(H_PAGE_INIT, H_PAGE_SET_ACTIVE, vpa + i, 0); + + for (i -= cmo_page_sz; rc && i != 0; i -= cmo_page_sz) + plpar_hcall_norets(H_PAGE_INIT, H_PAGE_SET_LOANED, + vpa + i - cmo_page_sz, 0); + + return rc; } extern void vpa_init(int cpu); -- GitLab From ac22429df22c1c793245c3cca33ccde4046d9c1f Mon Sep 17 00:00:00 2001 From: Robert Jennings Date: Sat, 16 Aug 2008 05:10:18 +1000 Subject: [PATCH 519/750] powerpc: Add CMO enabled flag and paging space data to lparcfg Add a field in lparcfg output to indicate whether the kernel is running on a dedicated or shared memory lpar. Added fields to show the paging space pool IDs and the CMO page size. Submitted-by: Robert Jennings Signed-off-by: Paul Mackerras --- arch/powerpc/kernel/lparcfg.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/powerpc/kernel/lparcfg.c b/arch/powerpc/kernel/lparcfg.c index 1a09719c762..b3eef30b513 100644 --- a/arch/powerpc/kernel/lparcfg.c +++ b/arch/powerpc/kernel/lparcfg.c @@ -416,6 +416,8 @@ static void pseries_cmo_data(struct seq_file *m) unsigned long cmo_faults = 0; unsigned long cmo_fault_time = 0; + seq_printf(m, "cmo_enabled=%d\n", firmware_has_feature(FW_FEATURE_CMO)); + if (!firmware_has_feature(FW_FEATURE_CMO)) return; @@ -427,6 +429,9 @@ static void pseries_cmo_data(struct seq_file *m) seq_printf(m, "cmo_faults=%lu\n", cmo_faults); seq_printf(m, "cmo_fault_time_usec=%lu\n", cmo_fault_time / tb_ticks_per_usec); + seq_printf(m, "cmo_primary_psp=%d\n", cmo_get_primary_psp()); + seq_printf(m, "cmo_secondary_psp=%d\n", cmo_get_secondary_psp()); + seq_printf(m, "cmo_page_size=%lu\n", cmo_get_page_size()); } static int pseries_lparcfg_data(struct seq_file *m, void *v) -- GitLab From b9754568ef173cc8dbe4145c3aa44203a4424692 Mon Sep 17 00:00:00 2001 From: Steven Rostedt Date: Sat, 16 Aug 2008 13:56:44 +1000 Subject: [PATCH 520/750] powerpc: Remove dead module_find_bug code Doing some various "make randconfig", I came across an error when CONFIG_BUG was not set: arch/powerpc/kernel/module.c: In function 'module_find_bug': arch/powerpc/kernel/module.c:111: error: increment of pointer to unknown structure arch/powerpc/kernel/module.c:111: error: arithmetic on pointer to an incomplete type arch/powerpc/kernel/module.c:112: error: dereferencing pointer to incomplete type Looking further into this, I found that module_find_bug, defined in powerpc arch code, is not called anywhere, so this just removes it. There is a static module_find_bug in lib/bug.c but that is a separate issue. Signed-off-by: Steven Rostedt Signed-off-by: Paul Mackerras --- arch/powerpc/kernel/module.c | 15 --------------- 1 file changed, 15 deletions(-) diff --git a/arch/powerpc/kernel/module.c b/arch/powerpc/kernel/module.c index af07003573c..7ff29247526 100644 --- a/arch/powerpc/kernel/module.c +++ b/arch/powerpc/kernel/module.c @@ -99,18 +99,3 @@ void module_arch_cleanup(struct module *mod) { module_bug_cleanup(mod); } - -struct bug_entry *module_find_bug(unsigned long bugaddr) -{ - struct mod_arch_specific *mod; - unsigned int i; - struct bug_entry *bug; - - list_for_each_entry(mod, &module_bug_list, bug_list) { - bug = mod->bug_table; - for (i = 0; i < mod->num_bugs; ++i, ++bug) - if (bugaddr == bug->bug_addr) - return bug; - } - return NULL; -} -- GitLab From d9178f4c14c3215fec66d326fcaff74262336aed Mon Sep 17 00:00:00 2001 From: Paul Collins Date: Sat, 16 Aug 2008 18:55:54 +1000 Subject: [PATCH 521/750] powerpc/kexec: Fix up KEXEC_CONTROL_CODE_SIZE missed during conversion Commit 163f6876f5c3ff8215e900b93779e960a56b3694 missed one, resulting in the following compile error: AS arch/powerpc/kernel/misc_32.o arch/powerpc/kernel/misc_32.S: Assembler messages: arch/powerpc/kernel/misc_32.S:902: Error: unsupported relocation against KEXEC_CONTROL_CODE_SIZE make[2]: *** [arch/powerpc/kernel/misc_32.o] Error 1 make[1]: *** [arch/powerpc/kernel] Error 2 make: *** [vmlinux] Error 2 I grepped arch/ and found no further instances. Signed-off-by: Paul Collins Signed-off-by: Paul Mackerras --- arch/powerpc/kernel/misc_32.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/powerpc/kernel/misc_32.S b/arch/powerpc/kernel/misc_32.S index 6321ae36f72..7a6dfbca768 100644 --- a/arch/powerpc/kernel/misc_32.S +++ b/arch/powerpc/kernel/misc_32.S @@ -899,7 +899,7 @@ relocate_new_kernel: /* set a new stack at the bottom of our page... */ /* (not really needed now) */ - addi r1, r4, KEXEC_CONTROL_CODE_SIZE - 8 /* for LR Save+Back Chain */ + addi r1, r4, KEXEC_CONTROL_PAGE_SIZE - 8 /* for LR Save+Back Chain */ stw r0, 0(r1) /* Do the copies */ -- GitLab From 50d0b17645a26d2877c9d5538114498c3f82adac Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Sun, 17 Aug 2008 03:57:30 +1000 Subject: [PATCH 522/750] powerpc: Use generic compat_sys_old_readdir Use the generic compat_sys_old_readdir instead of the powerpc one which is almost the same except for the almost complete lack of error handling. Note that we can't just use SYSCALL() in systbl.h because the native syscall is named old_readdir, not sys_old_readdir. Signed-off-by: Christoph Hellwig Signed-off-by: Paul Mackerras --- arch/powerpc/include/asm/systbl.h | 2 +- arch/powerpc/kernel/sys_ppc32.c | 57 ------------------------------- 2 files changed, 1 insertion(+), 58 deletions(-) diff --git a/arch/powerpc/include/asm/systbl.h b/arch/powerpc/include/asm/systbl.h index e084272ed1c..f6cc7a43b4f 100644 --- a/arch/powerpc/include/asm/systbl.h +++ b/arch/powerpc/include/asm/systbl.h @@ -92,7 +92,7 @@ COMPAT_SYS_SPU(readlink) SYSCALL(uselib) SYSCALL(swapon) SYSCALL(reboot) -SYSX(sys_ni_syscall,old32_readdir,old_readdir) +SYSX(sys_ni_syscall,compat_sys_old_readdir,old_readdir) SYSCALL_SPU(mmap) SYSCALL_SPU(munmap) SYSCALL_SPU(truncate) diff --git a/arch/powerpc/kernel/sys_ppc32.c b/arch/powerpc/kernel/sys_ppc32.c index 709f8cb8bfc..d98634c7606 100644 --- a/arch/powerpc/kernel/sys_ppc32.c +++ b/arch/powerpc/kernel/sys_ppc32.c @@ -52,63 +52,6 @@ #include #include -struct old_linux_dirent32 { - u32 d_ino; - u32 d_offset; - unsigned short d_namlen; - char d_name[1]; -}; - -struct readdir_callback32 { - struct old_linux_dirent32 __user * dirent; - int count; -}; - -static int fillonedir(void * __buf, const char * name, int namlen, - off_t offset, u64 ino, unsigned int d_type) -{ - struct readdir_callback32 * buf = (struct readdir_callback32 *) __buf; - struct old_linux_dirent32 __user * dirent; - ino_t d_ino; - - if (buf->count) - return -EINVAL; - d_ino = ino; - if (sizeof(d_ino) < sizeof(ino) && d_ino != ino) - return -EOVERFLOW; - buf->count++; - dirent = buf->dirent; - put_user(d_ino, &dirent->d_ino); - put_user(offset, &dirent->d_offset); - put_user(namlen, &dirent->d_namlen); - copy_to_user(dirent->d_name, name, namlen); - put_user(0, dirent->d_name + namlen); - return 0; -} - -asmlinkage int old32_readdir(unsigned int fd, struct old_linux_dirent32 __user *dirent, unsigned int count) -{ - int error = -EBADF; - struct file * file; - struct readdir_callback32 buf; - - file = fget(fd); - if (!file) - goto out; - - buf.count = 0; - buf.dirent = dirent; - - error = vfs_readdir(file, (filldir_t)fillonedir, &buf); - if (error < 0) - goto out_putf; - error = buf.count; - -out_putf: - fput(file); -out: - return error; -} asmlinkage long ppc32_select(u32 n, compat_ulong_t __user *inp, compat_ulong_t __user *outp, compat_ulong_t __user *exp, -- GitLab From a9312ae89324438b0edc554eb36c3ec6bf927d04 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Sun, 17 Aug 2008 21:51:03 -0700 Subject: [PATCH 523/750] pkt_sched: Add 'deactivated' state. This new state lets dev_deactivate() mark a qdisc as having been deactivated. dev_queue_xmit() and ing_filter() check for this bit and do not try to process the qdisc if the bit is set. dev_deactivate() polls the qdisc after setting the bit, waiting for both __QDISC_STATE_RUNNING and __QDISC_STATE_SCHED to clear. This isn't perfect yet, but subsequent changesets will make it so. This part is just one piece of the puzzle. Signed-off-by: David S. Miller --- include/net/sch_generic.h | 1 + net/core/dev.c | 9 ++++++++- net/sched/sch_generic.c | 6 ++++++ 3 files changed, 15 insertions(+), 1 deletion(-) diff --git a/include/net/sch_generic.h b/include/net/sch_generic.h index a7abfda3e44..757ab087adb 100644 --- a/include/net/sch_generic.h +++ b/include/net/sch_generic.h @@ -27,6 +27,7 @@ enum qdisc_state_t { __QDISC_STATE_RUNNING, __QDISC_STATE_SCHED, + __QDISC_STATE_DEACTIVATED, }; struct qdisc_size_table { diff --git a/net/core/dev.c b/net/core/dev.c index 600bb23c4c2..d9e31f63ade 100644 --- a/net/core/dev.c +++ b/net/core/dev.c @@ -1800,6 +1800,12 @@ gso: spin_lock(root_lock); + if (unlikely(test_bit(__QDISC_STATE_DEACTIVATED, &q->state))) { + spin_unlock(root_lock); + rc = NET_XMIT_DROP; + goto out_kfree_skb; + } + rc = qdisc_enqueue_root(skb, q); qdisc_run(q); @@ -2084,7 +2090,8 @@ static int ing_filter(struct sk_buff *skb) q = rxq->qdisc; if (q != &noop_qdisc) { spin_lock(qdisc_lock(q)); - result = qdisc_enqueue_root(skb, q); + if (likely(!test_bit(__QDISC_STATE_DEACTIVATED, &q->state))) + result = qdisc_enqueue_root(skb, q); spin_unlock(qdisc_lock(q)); } diff --git a/net/sched/sch_generic.c b/net/sched/sch_generic.c index 468574682ca..ff1c4557e5f 100644 --- a/net/sched/sch_generic.c +++ b/net/sched/sch_generic.c @@ -597,6 +597,9 @@ static void transition_one_qdisc(struct net_device *dev, struct Qdisc *new_qdisc = dev_queue->qdisc_sleeping; int *need_watchdog_p = _need_watchdog; + if (!(new_qdisc->flags & TCQ_F_BUILTIN)) + clear_bit(__QDISC_STATE_DEACTIVATED, &new_qdisc->state); + rcu_assign_pointer(dev_queue->qdisc, new_qdisc); if (need_watchdog_p && new_qdisc != &noqueue_qdisc) *need_watchdog_p = 1; @@ -640,6 +643,9 @@ static void dev_deactivate_queue(struct net_device *dev, if (qdisc) { spin_lock_bh(qdisc_lock(qdisc)); + if (!(qdisc->flags & TCQ_F_BUILTIN)) + set_bit(__QDISC_STATE_DEACTIVATED, &qdisc->state); + dev_queue->qdisc = qdisc_default; qdisc_reset(qdisc); -- GitLab From def82a1db1fdc4f861c77009e2ee86870c3743b0 Mon Sep 17 00:00:00 2001 From: Jarek Poplawski Date: Sun, 17 Aug 2008 21:54:43 -0700 Subject: [PATCH 524/750] net: Change handling of the __QDISC_STATE_SCHED flag in net_tx_action(). Change handling of the __QDISC_STATE_SCHED flag in net_tx_action() to enable proper control in dev_deactivate(). Now, if this flag is seen as unset under root_lock means a qdisc can't be netif_scheduled. Signed-off-by: Jarek Poplawski Signed-off-by: David S. Miller --- net/core/dev.c | 34 +++++++++++++++++++--------------- 1 file changed, 19 insertions(+), 15 deletions(-) diff --git a/net/core/dev.c b/net/core/dev.c index d9e31f63ade..819f0175bdc 100644 --- a/net/core/dev.c +++ b/net/core/dev.c @@ -1339,19 +1339,23 @@ static void dev_queue_xmit_nit(struct sk_buff *skb, struct net_device *dev) } -void __netif_schedule(struct Qdisc *q) +static inline void __netif_reschedule(struct Qdisc *q) { - if (!test_and_set_bit(__QDISC_STATE_SCHED, &q->state)) { - struct softnet_data *sd; - unsigned long flags; + struct softnet_data *sd; + unsigned long flags; - local_irq_save(flags); - sd = &__get_cpu_var(softnet_data); - q->next_sched = sd->output_queue; - sd->output_queue = q; - raise_softirq_irqoff(NET_TX_SOFTIRQ); - local_irq_restore(flags); - } + local_irq_save(flags); + sd = &__get_cpu_var(softnet_data); + q->next_sched = sd->output_queue; + sd->output_queue = q; + raise_softirq_irqoff(NET_TX_SOFTIRQ); + local_irq_restore(flags); +} + +void __netif_schedule(struct Qdisc *q) +{ + if (!test_and_set_bit(__QDISC_STATE_SCHED, &q->state)) + __netif_reschedule(q); } EXPORT_SYMBOL(__netif_schedule); @@ -1980,15 +1984,15 @@ static void net_tx_action(struct softirq_action *h) head = head->next_sched; - smp_mb__before_clear_bit(); - clear_bit(__QDISC_STATE_SCHED, &q->state); - root_lock = qdisc_lock(q); if (spin_trylock(root_lock)) { + smp_mb__before_clear_bit(); + clear_bit(__QDISC_STATE_SCHED, + &q->state); qdisc_run(q); spin_unlock(root_lock); } else { - __netif_schedule(q); + __netif_reschedule(q); } } } -- GitLab From 4335cd2da1e8986fa8aff21a91144d986cb0a5fc Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Sun, 17 Aug 2008 21:58:07 -0700 Subject: [PATCH 525/750] pkt_sched: Simplify dev_deactivate() polling loop. The condition under which the previous qdisc has no more references after we've attached &noop_qdisc is that both RUNNING and SCHED are both seen clear while holding the root lock. So just make specifically that check in the polling loop, instead of this overly complex "check without then check with lock held" sequence. Signed-off-by: David S. Miller --- net/sched/sch_generic.c | 31 +++++-------------------------- 1 file changed, 5 insertions(+), 26 deletions(-) diff --git a/net/sched/sch_generic.c b/net/sched/sch_generic.c index ff1c4557e5f..30b76aec723 100644 --- a/net/sched/sch_generic.c +++ b/net/sched/sch_generic.c @@ -653,7 +653,7 @@ static void dev_deactivate_queue(struct net_device *dev, } } -static bool some_qdisc_is_busy(struct net_device *dev, int lock) +static bool some_qdisc_is_busy(struct net_device *dev) { unsigned int i; @@ -667,14 +667,12 @@ static bool some_qdisc_is_busy(struct net_device *dev, int lock) q = dev_queue->qdisc_sleeping; root_lock = qdisc_lock(q); - if (lock) - spin_lock_bh(root_lock); + spin_lock_bh(root_lock); val = (test_bit(__QDISC_STATE_RUNNING, &q->state) || test_bit(__QDISC_STATE_SCHED, &q->state)); - if (lock) - spin_unlock_bh(root_lock); + spin_unlock_bh(root_lock); if (val) return true; @@ -684,8 +682,6 @@ static bool some_qdisc_is_busy(struct net_device *dev, int lock) void dev_deactivate(struct net_device *dev) { - bool running; - netdev_for_each_tx_queue(dev, dev_deactivate_queue, &noop_qdisc); dev_deactivate_queue(dev, &dev->rx_queue, &noop_qdisc); @@ -695,25 +691,8 @@ void dev_deactivate(struct net_device *dev) synchronize_rcu(); /* Wait for outstanding qdisc_run calls. */ - do { - while (some_qdisc_is_busy(dev, 0)) - yield(); - - /* - * Double-check inside queue lock to ensure that all effects - * of the queue run are visible when we return. - */ - running = some_qdisc_is_busy(dev, 1); - - /* - * The running flag should never be set at this point because - * we've already set dev->qdisc to noop_qdisc *inside* the same - * pair of spin locks. That is, if any qdisc_run starts after - * our initial test it should see the noop_qdisc and then - * clear the RUNNING bit before dropping the queue lock. So - * if it is set here then we've found a bug. - */ - } while (WARN_ON_ONCE(running)); + while (some_qdisc_is_busy(dev)) + yield(); } static void dev_init_scheduler_queue(struct net_device *dev, -- GitLab From 3a76e3716b4e571f5d91a20b6afb412560599083 Mon Sep 17 00:00:00 2001 From: Jarek Poplawski Date: Sun, 17 Aug 2008 22:02:11 -0700 Subject: [PATCH 526/750] pkt_sched: Grab correct lock in notify_and_destroy(). From: Jarek Poplawski When we are destroying non-root qdiscs, we need to lock the root of the qdisc tree not the the qdisc itself. Signed-off-by: David S. Miller --- net/sched/sch_api.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/net/sched/sch_api.c b/net/sched/sch_api.c index c25465e5607..c8dc72e1210 100644 --- a/net/sched/sch_api.c +++ b/net/sched/sch_api.c @@ -638,9 +638,9 @@ static void notify_and_destroy(struct sk_buff *skb, struct nlmsghdr *n, u32 clid qdisc_notify(skb, n, clid, old, new); if (old) { - spin_lock_bh(&old->q.lock); + sch_tree_lock(old); qdisc_destroy(old); - spin_unlock_bh(&old->q.lock); + sch_tree_unlock(old); } } -- GitLab From 1e0d5a5747772182d1bb2525d8153da640fdfb58 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Sun, 17 Aug 2008 22:31:26 -0700 Subject: [PATCH 527/750] pkt_sched: No longer destroy qdiscs from RCU. We can now kill them synchronously with all of the previous dev_deactivate() cures. This makes netdev destruction and shutdown saner as the qdiscs hold references to the device. Signed-off-by: David S. Miller --- include/net/sch_generic.h | 1 - net/sched/sch_generic.c | 27 +++++++++------------------ 2 files changed, 9 insertions(+), 19 deletions(-) diff --git a/include/net/sch_generic.h b/include/net/sch_generic.h index 757ab087adb..84d25f2e618 100644 --- a/include/net/sch_generic.h +++ b/include/net/sch_generic.h @@ -61,7 +61,6 @@ struct Qdisc struct gnet_stats_basic bstats; struct gnet_stats_queue qstats; struct gnet_stats_rate_est rate_est; - struct rcu_head q_rcu; int (*reshape_fail)(struct sk_buff *skb, struct Qdisc *q); diff --git a/net/sched/sch_generic.c b/net/sched/sch_generic.c index 30b76aec723..6f96b7bc080 100644 --- a/net/sched/sch_generic.c +++ b/net/sched/sch_generic.c @@ -518,14 +518,19 @@ void qdisc_reset(struct Qdisc *qdisc) } EXPORT_SYMBOL(qdisc_reset); -/* this is the rcu callback function to clean up a qdisc when there - * are no further references to it */ +/* Under qdisc_lock(qdisc) and BH! */ -static void __qdisc_destroy(struct rcu_head *head) +void qdisc_destroy(struct Qdisc *qdisc) { - struct Qdisc *qdisc = container_of(head, struct Qdisc, q_rcu); const struct Qdisc_ops *ops = qdisc->ops; + if (qdisc->flags & TCQ_F_BUILTIN || + !atomic_dec_and_test(&qdisc->refcnt)) + return; + + if (qdisc->parent) + list_del(&qdisc->list); + #ifdef CONFIG_NET_SCHED qdisc_put_stab(qdisc->stab); #endif @@ -542,20 +547,6 @@ static void __qdisc_destroy(struct rcu_head *head) kfree((char *) qdisc - qdisc->padded); } - -/* Under qdisc_lock(qdisc) and BH! */ - -void qdisc_destroy(struct Qdisc *qdisc) -{ - if (qdisc->flags & TCQ_F_BUILTIN || - !atomic_dec_and_test(&qdisc->refcnt)) - return; - - if (qdisc->parent) - list_del(&qdisc->list); - - call_rcu(&qdisc->q_rcu, __qdisc_destroy); -} EXPORT_SYMBOL(qdisc_destroy); static bool dev_all_qdisc_sleeping_noop(struct net_device *dev) -- GitLab From 0d40b6e564bad2047b57a9afc48b701ef3243b89 Mon Sep 17 00:00:00 2001 From: Jussi Kivilinna Date: Sun, 17 Aug 2008 22:43:56 -0700 Subject: [PATCH 528/750] sch_prio: Use return value from inner qdisc requeue Use return value from inner qdisc requeue when value returned isn't NET_XMIT_SUCCESS, instead of always returning NET_XMIT_DROP. Signed-off-by: Jussi Kivilinna Signed-off-by: David S. Miller --- net/sched/sch_prio.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/sched/sch_prio.c b/net/sched/sch_prio.c index eac197610ed..7cdc3e6b31e 100644 --- a/net/sched/sch_prio.c +++ b/net/sched/sch_prio.c @@ -117,7 +117,7 @@ prio_requeue(struct sk_buff *skb, struct Qdisc* sch) } if (net_xmit_drop_count(ret)) sch->qstats.drops++; - return NET_XMIT_DROP; + return ret; } -- GitLab From 4cf7cb280e4fcfcd7ae7429e17d798d3a44087af Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Sun, 17 Aug 2008 22:45:17 -0700 Subject: [PATCH 529/750] sch_prio: Use NET_XMIT_SUCCESS instead of "0" constant. Signed-off-by: David S. Miller --- net/sched/sch_prio.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/sched/sch_prio.c b/net/sched/sch_prio.c index 7cdc3e6b31e..a6697c686c7 100644 --- a/net/sched/sch_prio.c +++ b/net/sched/sch_prio.c @@ -113,7 +113,7 @@ prio_requeue(struct sk_buff *skb, struct Qdisc* sch) if ((ret = qdisc->ops->requeue(skb, qdisc)) == NET_XMIT_SUCCESS) { sch->q.qlen++; sch->qstats.requeues++; - return 0; + return NET_XMIT_SUCCESS; } if (net_xmit_drop_count(ret)) sch->qstats.drops++; -- GitLab From 3c3b5c3b0bf798316a410e27e3d7e6f015663602 Mon Sep 17 00:00:00 2001 From: Mathieu Desnoyers Date: Sat, 16 Aug 2008 03:39:26 -0400 Subject: [PATCH 530/750] x86: correct register constraints for 64-bit atomic operations x86_64 add/sub atomic ops does not seems to accept integer values bigger than 32 bits as immediates. Intel's add/sub documentation specifies they have to be passed as registers. The only operations in the x86-64 architecture which accept arbitrary 64-bit immediates is "movq" to any register; similarly, the only operation which accept arbitrary 64-bit displacement is "movabs" to or from al/ax/eax/rax. http://gcc.gnu.org/onlinedocs/gcc-4.3.0/gcc/Machine-Constraints.html states : e 32-bit signed integer constant, or a symbolic reference known to fit that range (for immediate operands in sign-extending x86-64 instructions). Z 32-bit unsigned integer constant, or a symbolic reference known to fit that range (for immediate operands in zero-extending x86-64 instructions). Since add/sub does sign extension, using the "e" constraint seems appropriate. It applies to 2.6.27-rc, 2.6.26, 2.6.25... Signed-off-by: Mathieu Desnoyers Signed-off-by: H. Peter Anvin Signed-off-by: Ingo Molnar --- include/asm-x86/atomic_64.h | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/include/asm-x86/atomic_64.h b/include/asm-x86/atomic_64.h index a0095191c02..91c7d03e65b 100644 --- a/include/asm-x86/atomic_64.h +++ b/include/asm-x86/atomic_64.h @@ -228,7 +228,7 @@ static inline void atomic64_add(long i, atomic64_t *v) { asm volatile(LOCK_PREFIX "addq %1,%0" : "=m" (v->counter) - : "ir" (i), "m" (v->counter)); + : "er" (i), "m" (v->counter)); } /** @@ -242,7 +242,7 @@ static inline void atomic64_sub(long i, atomic64_t *v) { asm volatile(LOCK_PREFIX "subq %1,%0" : "=m" (v->counter) - : "ir" (i), "m" (v->counter)); + : "er" (i), "m" (v->counter)); } /** @@ -260,7 +260,7 @@ static inline int atomic64_sub_and_test(long i, atomic64_t *v) asm volatile(LOCK_PREFIX "subq %2,%0; sete %1" : "=m" (v->counter), "=qm" (c) - : "ir" (i), "m" (v->counter) : "memory"); + : "er" (i), "m" (v->counter) : "memory"); return c; } @@ -341,7 +341,7 @@ static inline int atomic64_add_negative(long i, atomic64_t *v) asm volatile(LOCK_PREFIX "addq %2,%0; sets %1" : "=m" (v->counter), "=qm" (c) - : "ir" (i), "m" (v->counter) : "memory"); + : "er" (i), "m" (v->counter) : "memory"); return c; } -- GitLab From d554d9a4295dd0595d12eeccbc55d1f495b15176 Mon Sep 17 00:00:00 2001 From: Marcin Slusarz Date: Mon, 11 Aug 2008 00:07:44 +0200 Subject: [PATCH 531/750] x86, tsc: fix section mismatch warning WARNING: vmlinux.o(.text+0x7950): Section mismatch in reference from the function native_calibrate_tsc() to the function .init.text:tsc_read_refs() The function native_calibrate_tsc() references the function __init tsc_read_refs(). This is often because native_calibrate_tsc lacks a __init annotation or the annotation of tsc_read_refs is wrong. tsc_read_refs is called from native_calibrate_tsc which is not __init and native_calibrate_tsc cannot be marked __init Signed-off-by: Marcin Slusarz Signed-off-by: H. Peter Anvin Signed-off-by: Ingo Molnar --- arch/x86/kernel/tsc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/tsc.c b/arch/x86/kernel/tsc.c index 7603c055390..46af7167673 100644 --- a/arch/x86/kernel/tsc.c +++ b/arch/x86/kernel/tsc.c @@ -104,7 +104,7 @@ __setup("notsc", notsc_setup); /* * Read TSC and the reference counters. Take care of SMI disturbance */ -static u64 __init tsc_read_refs(u64 *pm, u64 *hpet) +static u64 tsc_read_refs(u64 *pm, u64 *hpet) { u64 t1, t2; int i; -- GitLab From 67d0c9ebdc9f5f356657146b4e862b2d745e9e78 Mon Sep 17 00:00:00 2001 From: Marcin Slusarz Date: Mon, 11 Aug 2008 00:12:37 +0200 Subject: [PATCH 532/750] x86: fix MP_processor_info section mismatch warning WARNING: arch/x86/kernel/built-in.o(.cpuinit.text+0x1fe7): Section mismatch in reference from the function MP_processor_info() to the variable .init.data:x86_quirks The function __cpuinit MP_processor_info() references a variable __initdata x86_quirks. If x86_quirks is only used by MP_processor_info then annotate x86_quirks with a matching annotation. MP_processor_info uses x86_quirks which is __init and is used only from smp_read_mpc and construct_default_ISA_mptable which are __init Signed-off-by: Marcin Slusarz Signed-off-by: H. Peter Anvin Signed-off-by: Ingo Molnar --- arch/x86/kernel/mpparse.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/mpparse.c b/arch/x86/kernel/mpparse.c index 678090508a6..9942fc72b63 100644 --- a/arch/x86/kernel/mpparse.c +++ b/arch/x86/kernel/mpparse.c @@ -49,7 +49,7 @@ static int __init mpf_checksum(unsigned char *mp, int len) return sum & 0xFF; } -static void __cpuinit MP_processor_info(struct mpc_config_processor *m) +static void __init MP_processor_info(struct mpc_config_processor *m) { int apicid; char *bootup_cpu = ""; -- GitLab From c72a5efec1193faa2ef34c0bd48d7251a70ec934 Mon Sep 17 00:00:00 2001 From: Marcin Slusarz Date: Mon, 11 Aug 2008 00:11:13 +0200 Subject: [PATCH 533/750] x86: mmconf: fix section mismatch warning WARNING: arch/x86/kernel/built-in.o(.cpuinit.text+0x1591): Section mismatch in reference from the function init_amd() to the function .init.text:check_enable_amd_mmconf_dmi() The function __cpuinit init_amd() references a function __init check_enable_amd_mmconf_dmi(). If check_enable_amd_mmconf_dmi is only used by init_amd then annotate check_enable_amd_mmconf_dmi with a matching annotation. check_enable_amd_mmconf_dmi is only called from init_amd which is __cpuinit Signed-off-by: Marcin Slusarz Signed-off-by: H. Peter Anvin Signed-off-by: Ingo Molnar --- arch/x86/kernel/mmconf-fam10h_64.c | 2 +- include/asm-x86/mmconfig.h | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/x86/kernel/mmconf-fam10h_64.c b/arch/x86/kernel/mmconf-fam10h_64.c index fdfdc550b36..efc2f361fe8 100644 --- a/arch/x86/kernel/mmconf-fam10h_64.c +++ b/arch/x86/kernel/mmconf-fam10h_64.c @@ -238,7 +238,7 @@ static struct dmi_system_id __devinitdata mmconf_dmi_table[] = { {} }; -void __init check_enable_amd_mmconf_dmi(void) +void __cpuinit check_enable_amd_mmconf_dmi(void) { dmi_check_system(mmconf_dmi_table); } diff --git a/include/asm-x86/mmconfig.h b/include/asm-x86/mmconfig.h index 95beda07c6f..e293ab81e85 100644 --- a/include/asm-x86/mmconfig.h +++ b/include/asm-x86/mmconfig.h @@ -3,7 +3,7 @@ #ifdef CONFIG_PCI_MMCONFIG extern void __cpuinit fam10h_check_enable_mmcfg(void); -extern void __init check_enable_amd_mmconf_dmi(void); +extern void __cpuinit check_enable_amd_mmconf_dmi(void); #else static inline void fam10h_check_enable_mmcfg(void) { } static inline void check_enable_amd_mmconf_dmi(void) { } -- GitLab From 39e00fe20aaad4326ed5e0e3221451732bc7f679 Mon Sep 17 00:00:00 2001 From: Marcin Slusarz Date: Mon, 11 Aug 2008 00:09:38 +0200 Subject: [PATCH 534/750] x86: mpparse.c: fix section mismatch warning WARNING: vmlinux.o(.text+0x118f7): Section mismatch in reference from the function construct_ioapic_table() to the function .init.text:MP_bus_info() The function construct_ioapic_table() references the function __init MP_bus_info(). This is often because construct_ioapic_table lacks a __init annotation or the annotation of MP_bus_info is wrong. construct_ioapic_table is called only from construct_default_ISA_mptable which is __init Signed-off-by: Marcin Slusarz Signed-off-by: H. Peter Anvin Signed-off-by: Ingo Molnar --- arch/x86/kernel/mpparse.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/x86/kernel/mpparse.c b/arch/x86/kernel/mpparse.c index 9942fc72b63..b3fb430725c 100644 --- a/arch/x86/kernel/mpparse.c +++ b/arch/x86/kernel/mpparse.c @@ -484,7 +484,7 @@ static void __init construct_default_ioirq_mptable(int mpc_default_type) } -static void construct_ioapic_table(int mpc_default_type) +static void __init construct_ioapic_table(int mpc_default_type) { struct mpc_config_ioapic ioapic; struct mpc_config_bus bus; @@ -529,7 +529,7 @@ static void construct_ioapic_table(int mpc_default_type) construct_default_ioirq_mptable(mpc_default_type); } #else -static inline void construct_ioapic_table(int mpc_default_type) { } +static inline void __init construct_ioapic_table(int mpc_default_type) { } #endif static inline void __init construct_default_ISA_mptable(int mpc_default_type) -- GitLab From 13601cd8e44aab332cedff1d6dc10786ec890b7b Mon Sep 17 00:00:00 2001 From: Yang Hongyang Date: Sun, 17 Aug 2008 23:21:52 -0700 Subject: [PATCH 535/750] ipv6: Fix the return interface index when get it while no message is received. When get receiving interface index while no message is received, the bounded device's index of the socket should be returned. RFC 3542: Issuing getsockopt() for the above options will return the sticky option value i.e., the value set with setsockopt(). If no sticky option value has been set getsockopt() will return the following values: - For the IPV6_PKTINFO option, it will return an in6_pktinfo structure with ipi6_addr being in6addr_any and ipi6_ifindex being zero. Signed-off-by: Yang Hongyang Signed-off-by: David S. Miller --- net/ipv6/ipv6_sockglue.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/net/ipv6/ipv6_sockglue.c b/net/ipv6/ipv6_sockglue.c index 741cfcd96f8..4e5eac301f9 100644 --- a/net/ipv6/ipv6_sockglue.c +++ b/net/ipv6/ipv6_sockglue.c @@ -911,7 +911,7 @@ static int do_ipv6_getsockopt(struct sock *sk, int level, int optname, } else { if (np->rxopt.bits.rxinfo) { struct in6_pktinfo src_info; - src_info.ipi6_ifindex = np->mcast_oif; + src_info.ipi6_ifindex = np->mcast_oif ? np->mcast_oif : sk->sk_bound_dev_if; ipv6_addr_copy(&src_info.ipi6_addr, &np->daddr); put_cmsg(&msg, SOL_IPV6, IPV6_PKTINFO, sizeof(src_info), &src_info); } @@ -921,7 +921,7 @@ static int do_ipv6_getsockopt(struct sock *sk, int level, int optname, } if (np->rxopt.bits.rxoinfo) { struct in6_pktinfo src_info; - src_info.ipi6_ifindex = np->mcast_oif; + src_info.ipi6_ifindex = np->mcast_oif ? np->mcast_oif : sk->sk_bound_dev_if; ipv6_addr_copy(&src_info.ipi6_addr, &np->daddr); put_cmsg(&msg, SOL_IPV6, IPV6_2292PKTINFO, sizeof(src_info), &src_info); } -- GitLab From 96d203169d1d851ac1468f7d4459a09581be364c Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Sun, 17 Aug 2008 23:37:16 -0700 Subject: [PATCH 536/750] pkt_sched: Fix missed RCU unlock in dev_queue_xmit() Noticed by Jarek Poplawski. Signed-off-by: David S. Miller --- net/core/dev.c | 10 ++++------ 1 file changed, 4 insertions(+), 6 deletions(-) diff --git a/net/core/dev.c b/net/core/dev.c index 819f0175bdc..8d133802372 100644 --- a/net/core/dev.c +++ b/net/core/dev.c @@ -1805,14 +1805,12 @@ gso: spin_lock(root_lock); if (unlikely(test_bit(__QDISC_STATE_DEACTIVATED, &q->state))) { - spin_unlock(root_lock); + kfree_skb(skb); rc = NET_XMIT_DROP; - goto out_kfree_skb; + } else { + rc = qdisc_enqueue_root(skb, q); + qdisc_run(q); } - - rc = qdisc_enqueue_root(skb, q); - qdisc_run(q); - spin_unlock(root_lock); goto out; -- GitLab From e532c06f2a835b5cc4f4166f467437d9b09c1d0e Mon Sep 17 00:00:00 2001 From: David Fries Date: Sun, 17 Aug 2008 23:03:40 -0500 Subject: [PATCH 537/750] x86: fix i486 suspend to disk CR4 oops arch/x86/power/cpu_32.c __save_processor_state calls read_cr4() only a i486 CPU doesn't have the CR4 register. Trying to read it produces an invalid opcode oops during suspend to disk. Use the safe rc4 reading op instead. If the value to be written is zero the write is skipped. arch/x86/power/hibernate_asm_32.S done: swapped the use of %eax and %ecx to use jecxz for the zero test and jump over store to %cr4. restore_image: s/%ecx/%eax/ to be consistent with done: In addition to __save_processor_state, acpi_save_state_mem, efi_call_phys_prelog, and efi_call_phys_epilog had checks added (acpi restore was in assembly and already had a check for non-zero). There were other reads and writes of CR4, but MCE and virtualization shouldn't be executed on a i486 anyway. Signed-off-by: David Fries Acked-by: H. Peter Anvin Signed-off-by: Ingo Molnar --- arch/x86/kernel/acpi/sleep.c | 2 +- arch/x86/kernel/efi_32.c | 4 ++-- arch/x86/power/cpu_32.c | 6 ++++-- arch/x86/power/hibernate_asm_32.S | 26 +++++++++++++++----------- 4 files changed, 22 insertions(+), 16 deletions(-) diff --git a/arch/x86/kernel/acpi/sleep.c b/arch/x86/kernel/acpi/sleep.c index 81e5ab6542d..426e5d91b63 100644 --- a/arch/x86/kernel/acpi/sleep.c +++ b/arch/x86/kernel/acpi/sleep.c @@ -86,7 +86,7 @@ int acpi_save_state_mem(void) #endif /* !CONFIG_64BIT */ header->pmode_cr0 = read_cr0(); - header->pmode_cr4 = read_cr4(); + header->pmode_cr4 = read_cr4_safe(); header->realmode_flags = acpi_realmode_flags; header->real_magic = 0x12345678; diff --git a/arch/x86/kernel/efi_32.c b/arch/x86/kernel/efi_32.c index 4b63c8e1f13..5cab48ee61a 100644 --- a/arch/x86/kernel/efi_32.c +++ b/arch/x86/kernel/efi_32.c @@ -53,7 +53,7 @@ void efi_call_phys_prelog(void) * directory. If I have PAE, I just need to duplicate one entry in * page directory. */ - cr4 = read_cr4(); + cr4 = read_cr4_safe(); if (cr4 & X86_CR4_PAE) { efi_bak_pg_dir_pointer[0].pgd = @@ -91,7 +91,7 @@ void efi_call_phys_epilog(void) gdt_descr.size = GDT_SIZE - 1; load_gdt(&gdt_descr); - cr4 = read_cr4(); + cr4 = read_cr4_safe(); if (cr4 & X86_CR4_PAE) { swapper_pg_dir[pgd_index(0)].pgd = diff --git a/arch/x86/power/cpu_32.c b/arch/x86/power/cpu_32.c index 7dc5d5cf50a..d3e083dea72 100644 --- a/arch/x86/power/cpu_32.c +++ b/arch/x86/power/cpu_32.c @@ -45,7 +45,7 @@ static void __save_processor_state(struct saved_context *ctxt) ctxt->cr0 = read_cr0(); ctxt->cr2 = read_cr2(); ctxt->cr3 = read_cr3(); - ctxt->cr4 = read_cr4(); + ctxt->cr4 = read_cr4_safe(); } /* Needed by apm.c */ @@ -98,7 +98,9 @@ static void __restore_processor_state(struct saved_context *ctxt) /* * control registers */ - write_cr4(ctxt->cr4); + /* cr4 was introduced in the Pentium CPU */ + if (ctxt->cr4) + write_cr4(ctxt->cr4); write_cr3(ctxt->cr3); write_cr2(ctxt->cr2); write_cr0(ctxt->cr0); diff --git a/arch/x86/power/hibernate_asm_32.S b/arch/x86/power/hibernate_asm_32.S index b95aa6cfe3c..4fc7e872c85 100644 --- a/arch/x86/power/hibernate_asm_32.S +++ b/arch/x86/power/hibernate_asm_32.S @@ -28,9 +28,9 @@ ENTRY(swsusp_arch_suspend) ret ENTRY(restore_image) - movl resume_pg_dir, %ecx - subl $__PAGE_OFFSET, %ecx - movl %ecx, %cr3 + movl resume_pg_dir, %eax + subl $__PAGE_OFFSET, %eax + movl %eax, %cr3 movl restore_pblist, %edx .p2align 4,,7 @@ -52,17 +52,21 @@ copy_loop: done: /* go back to the original page tables */ - movl $swapper_pg_dir, %ecx - subl $__PAGE_OFFSET, %ecx - movl %ecx, %cr3 + movl $swapper_pg_dir, %eax + subl $__PAGE_OFFSET, %eax + movl %eax, %cr3 /* Flush TLB, including "global" things (vmalloc) */ - movl mmu_cr4_features, %eax - movl %eax, %edx + movl mmu_cr4_features, %ecx + jecxz 1f # cr4 Pentium and higher, skip if zero + movl %ecx, %edx andl $~(1<<7), %edx; # PGE movl %edx, %cr4; # turn off PGE - movl %cr3, %ecx; # flush TLB - movl %ecx, %cr3 - movl %eax, %cr4; # turn PGE back on +1: + movl %cr3, %eax; # flush TLB + movl %eax, %cr3 + jecxz 1f # cr4 Pentium and higher, skip if zero + movl %ecx, %cr4; # turn PGE back on +1: movl saved_context_esp, %esp movl saved_context_ebp, %ebp -- GitLab From c6a92a2501b35880d2e357dbd7f2cbc9a06f1058 Mon Sep 17 00:00:00 2001 From: Marcin Slusarz Date: Sun, 17 Aug 2008 17:50:50 +0200 Subject: [PATCH 538/750] x86, percpu: silence section mismatch warnings related to EARLY_PER_CPU variables Quoting Mike Travis in "x86: cleanup early per cpu variables/accesses v4" (23ca4bba3e20c6c3cb11c1bb0ab4770b724d39ac): The DEFINE macro defines the per_cpu variable as well as the early map and pointer. It also initializes the per_cpu variable and map elements to "_initvalue". The early_* macros provide access to the initial map (usually setup during system init) and the early pointer. This pointer is initialized to point to the early map but is then NULL'ed when the actual per_cpu areas are setup. After that the per_cpu variable is the correct access to the variable. As these variables are NULL'ed before __init sections are dropped (in setup_per_cpu_maps), they can be safely annotated as __ref. This change silences following section mismatch warnings: WARNING: vmlinux.o(.data+0x46c0): Section mismatch in reference from the variable x86_cpu_to_apicid_early_ptr to the variable .init.data:x86_cpu_to_apicid_early_map The variable x86_cpu_to_apicid_early_ptr references the variable __initdata x86_cpu_to_apicid_early_map If the reference is valid then annotate the variable with __init* (see linux/init.h) or name the variable: *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, WARNING: vmlinux.o(.data+0x46c8): Section mismatch in reference from the variable x86_bios_cpu_apicid_early_ptr to the variable .init.data:x86_bios_cpu_apicid_early_map The variable x86_bios_cpu_apicid_early_ptr references the variable __initdata x86_bios_cpu_apicid_early_map If the reference is valid then annotate the variable with __init* (see linux/init.h) or name the variable: *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, WARNING: vmlinux.o(.data+0x46d0): Section mismatch in reference from the variable x86_cpu_to_node_map_early_ptr to the variable .init.data:x86_cpu_to_node_map_early_map The variable x86_cpu_to_node_map_early_ptr references the variable __initdata x86_cpu_to_node_map_early_map If the reference is valid then annotate the variable with __init* (see linux/init.h) or name the variable: *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, Signed-off-by: Marcin Slusarz Cc: Mike Travis Signed-off-by: Ingo Molnar --- include/asm-x86/percpu.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/asm-x86/percpu.h b/include/asm-x86/percpu.h index 4e91ee1e37a..f643a3a92da 100644 --- a/include/asm-x86/percpu.h +++ b/include/asm-x86/percpu.h @@ -182,7 +182,7 @@ do { \ DEFINE_PER_CPU(_type, _name) = _initvalue; \ __typeof__(_type) _name##_early_map[NR_CPUS] __initdata = \ { [0 ... NR_CPUS-1] = _initvalue }; \ - __typeof__(_type) *_name##_early_ptr = _name##_early_map + __typeof__(_type) *_name##_early_ptr __refdata = _name##_early_map #define EXPORT_EARLY_PER_CPU_SYMBOL(_name) \ EXPORT_PER_CPU_SYMBOL(_name) -- GitLab From d19fbfdfe6a7034c8b6a7062365780485ab5aeaa Mon Sep 17 00:00:00 2001 From: Marcin Slusarz Date: Sun, 17 Aug 2008 17:50:51 +0200 Subject: [PATCH 539/750] x86: silence section mismatch warning - get_local_pda Take out part of get_local_pda referencing __init function (free_bootmem) to new (static) function marked as __ref. It's safe to do because free_bootmem is called before __init sections are dropped. WARNING: vmlinux.o(.cpuinit.text+0x3cd7): Section mismatch in reference from the function get_local_pda() to the function .init.text:free_bootmem() The function __cpuinit get_local_pda() references a function __init free_bootmem(). If free_bootmem is only used by get_local_pda then annotate free_bootmem with a matching annotation. Signed-off-by: Marcin Slusarz Cc: Mike Travis Signed-off-by: Ingo Molnar --- arch/x86/kernel/smpboot.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-) diff --git a/arch/x86/kernel/smpboot.c b/arch/x86/kernel/smpboot.c index a8fb8a980fa..e139e617f42 100644 --- a/arch/x86/kernel/smpboot.c +++ b/arch/x86/kernel/smpboot.c @@ -756,6 +756,14 @@ static void __cpuinit do_fork_idle(struct work_struct *work) } #ifdef CONFIG_X86_64 + +/* __ref because it's safe to call free_bootmem when after_bootmem == 0. */ +static void __ref free_bootmem_pda(struct x8664_pda *oldpda) +{ + if (!after_bootmem) + free_bootmem((unsigned long)oldpda, sizeof(*oldpda)); +} + /* * Allocate node local memory for the AP pda. * @@ -784,8 +792,7 @@ int __cpuinit get_local_pda(int cpu) if (oldpda) { memcpy(newpda, oldpda, size); - if (!after_bootmem) - free_bootmem((unsigned long)oldpda, size); + free_bootmem_pda(oldpda); } newpda->in_bootmem = 0; -- GitLab From f71066624d5d91bf179a1ea25da0800b72e20c60 Mon Sep 17 00:00:00 2001 From: Marcin Slusarz Date: Sun, 17 Aug 2008 17:50:52 +0200 Subject: [PATCH 540/750] x86, calgary: fix section mismatch warning - get_tce_space_from_tar WARNING: vmlinux.o(.text+0x27032): Section mismatch in reference from the function get_tce_space_from_tar() to the function .init.text:calgary_bus_has_devices() The function get_tce_space_from_tar() references the function __init calgary_bus_has_devices(). This is often because get_tce_space_from_tar lacks a __init annotation or the annotation of calgary_bus_has_devices is wrong. get_tce_space_from_tar is called only from __init function (calgary_init) and calls __init function (calgary_bus_has_devices). So annotate it properly. Signed-off-by: Marcin Slusarz Cc: Chandru Siddalingappa Signed-off-by: Ingo Molnar --- arch/x86/kernel/pci-calgary_64.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/pci-calgary_64.c b/arch/x86/kernel/pci-calgary_64.c index 02d19328525..218d783ed7a 100644 --- a/arch/x86/kernel/pci-calgary_64.c +++ b/arch/x86/kernel/pci-calgary_64.c @@ -1350,7 +1350,7 @@ static void calgary_init_bitmap_from_tce_table(struct iommu_table *tbl) * Function for kdump case. Get the tce tables from first kernel * by reading the contents of the base adress register of calgary iommu */ -static void get_tce_space_from_tar(void) +static void __init get_tce_space_from_tar(void) { int bus; void __iomem *target; -- GitLab From 1b72691ce35812ff865d778f303779e774d2b098 Mon Sep 17 00:00:00 2001 From: Andi Kleen Date: Mon, 18 Aug 2008 09:06:01 +0200 Subject: [PATCH 541/750] x86: fix build warnings in real mode code This recent patch commit c3965bd15118742d72b4bc1a290d37b3f081eb98 Author: Paul Jackson Date: Wed May 14 08:15:34 2008 -0700 x86 boot: proper use of ARRAY_SIZE instead of repeated E820MAX constant caused these new warnings during a normal build: In file included from linux-2.6/arch/x86/boot/memory.c:17: linux-2.6/include/linux/log2.h: In function '__ilog2_u32': linux-2.6/include/linux/log2.h:34: warning: implicit declaration of function 'fls' linux-2.6/include/linux/log2.h: In function '__ilog2_u64': linux-2.6/include/linux/log2.h:42: warning: implicit declaration of function 'fls64' linux-2.6/include/linux/log2.h: In function '__roundup_pow_of_two ': linux-2.6/include/linux/log2.h:63: warning: implicit declaration of function 'fls_long' I tried to fix them in log2.h, but it's difficult because the real mode environment is completely different from a normal kernel environment. Instead define an own ARRAY_SIZE macro in boot.h, similar to the other private macros there. Signed-off-by: Andi Kleen Signed-off-by: Ingo Molnar --- arch/x86/boot/boot.h | 2 ++ arch/x86/boot/memory.c | 1 - 2 files changed, 2 insertions(+), 1 deletion(-) diff --git a/arch/x86/boot/boot.h b/arch/x86/boot/boot.h index 616b804a229..cc0ef13fba7 100644 --- a/arch/x86/boot/boot.h +++ b/arch/x86/boot/boot.h @@ -30,6 +30,8 @@ /* Useful macros */ #define BUILD_BUG_ON(condition) ((void)sizeof(char[1 - 2*!!(condition)])) +#define ARRAY_SIZE(x) (sizeof(x) / sizeof(*(x))) + extern struct setup_header hdr; extern struct boot_params boot_params; diff --git a/arch/x86/boot/memory.c b/arch/x86/boot/memory.c index 53165c97336..8c3c25f3557 100644 --- a/arch/x86/boot/memory.c +++ b/arch/x86/boot/memory.c @@ -13,7 +13,6 @@ */ #include "boot.h" -#include #define SMAP 0x534d4150 /* ASCII "SMAP" */ -- GitLab From 69747650c814a8a79fef412c7416adf823293a3e Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Sun, 17 Aug 2008 23:55:36 -0700 Subject: [PATCH 542/750] pkt_sched: Fix return value corruption in HTB and TBF. Based upon a bug report by Josip Rodin. Packet schedulers should only return NET_XMIT_DROP iff the packet really was dropped. If the packet does reach the device after we return NET_XMIT_DROP then TCP can crash because it depends upon the enqueue path return values being accurate. Signed-off-by: David S. Miller --- net/sched/sch_htb.c | 4 ++-- net/sched/sch_tbf.c | 11 ++--------- 2 files changed, 4 insertions(+), 11 deletions(-) diff --git a/net/sched/sch_htb.c b/net/sched/sch_htb.c index 6febd245e62..0df0df202ed 100644 --- a/net/sched/sch_htb.c +++ b/net/sched/sch_htb.c @@ -577,7 +577,7 @@ static int htb_enqueue(struct sk_buff *skb, struct Qdisc *sch) sch->qstats.drops++; cl->qstats.drops++; } - return NET_XMIT_DROP; + return ret; } else { cl->bstats.packets += skb_is_gso(skb)?skb_shinfo(skb)->gso_segs:1; @@ -623,7 +623,7 @@ static int htb_requeue(struct sk_buff *skb, struct Qdisc *sch) sch->qstats.drops++; cl->qstats.drops++; } - return NET_XMIT_DROP; + return ret; } else htb_activate(q, cl); diff --git a/net/sched/sch_tbf.c b/net/sched/sch_tbf.c index 7d3b7ff3bf0..94c61598b86 100644 --- a/net/sched/sch_tbf.c +++ b/net/sched/sch_tbf.c @@ -123,15 +123,8 @@ static int tbf_enqueue(struct sk_buff *skb, struct Qdisc* sch) struct tbf_sched_data *q = qdisc_priv(sch); int ret; - if (qdisc_pkt_len(skb) > q->max_size) { - sch->qstats.drops++; -#ifdef CONFIG_NET_CLS_ACT - if (sch->reshape_fail == NULL || sch->reshape_fail(skb, sch)) -#endif - kfree_skb(skb); - - return NET_XMIT_DROP; - } + if (qdisc_pkt_len(skb) > q->max_size) + return qdisc_reshape_fail(skb, sch); ret = qdisc_enqueue(skb, q->qdisc); if (ret != 0) { -- GitLab From 6951b12a0fe7fc64789f2c4d62d2a304e93836a8 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Mon, 18 Aug 2008 04:26:37 +0400 Subject: [PATCH 543/750] lockdep: fix spurious 'inconsistent lock state' warning Since f82b217e3513fe3af342c0f3ee1494e86250c21c lockdep can output spurious warnings related to hwirqs due to hardirq_off shrinkage from int to bit-sized flag. Guard it with double negation to fix the warning. Signed-off-by: Dmitry Baryshkov Acked-by: Peter Zijlstra Signed-off-by: Ingo Molnar --- kernel/lockdep.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/lockdep.c b/kernel/lockdep.c index 77fa776a2da..3bfb1877a00 100644 --- a/kernel/lockdep.c +++ b/kernel/lockdep.c @@ -2582,7 +2582,7 @@ static int __lock_acquire(struct lockdep_map *lock, unsigned int subclass, hlock->trylock = trylock; hlock->read = read; hlock->check = check; - hlock->hardirqs_off = hardirqs_off; + hlock->hardirqs_off = !!hardirqs_off; #ifdef CONFIG_LOCK_STAT hlock->waittime_stamp = 0; hlock->holdtime_stamp = sched_clock(); -- GitLab From 9bfa35fe422c74882e27cc54450a5f76c96aad68 Mon Sep 17 00:00:00 2001 From: Marcel Holtmann Date: Mon, 18 Aug 2008 13:23:52 +0200 Subject: [PATCH 544/750] [Bluetooth] Add SCO support to btusb driver The new generic driver for Bluetooth USB devices was missing proper SCO support. The driver now claims the second interface for these USB devices to allow the flow of SCO packets. It also handles switching of the alternate setting and re-submission of isochronous URBs. The btusb driver is now a full replacement for hci_usb and thus the experimental tag has been removed and this driver is promoted as preferred one. Signed-off-by: Marcel Holtmann --- drivers/bluetooth/Kconfig | 10 +- drivers/bluetooth/btusb.c | 282 ++++++++++++++++++++++++++++++++++++-- 2 files changed, 272 insertions(+), 20 deletions(-) diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig index a235ca78746..7cb4029a537 100644 --- a/drivers/bluetooth/Kconfig +++ b/drivers/bluetooth/Kconfig @@ -3,8 +3,8 @@ menu "Bluetooth device drivers" depends on BT config BT_HCIUSB - tristate "HCI USB driver" - depends on USB + tristate "HCI USB driver (old version)" + depends on USB && BT_HCIBTUSB=n help Bluetooth HCI USB driver. This driver is required if you want to use Bluetooth devices with @@ -23,15 +23,13 @@ config BT_HCIUSB_SCO Say Y here to compile support for SCO over HCI USB. config BT_HCIBTUSB - tristate "HCI USB driver (alternate version)" - depends on USB && EXPERIMENTAL && BT_HCIUSB=n + tristate "HCI USB driver" + depends on USB help Bluetooth HCI USB driver. This driver is required if you want to use Bluetooth devices with USB interface. - This driver is still experimental and has no SCO support. - Say Y here to compile support for Bluetooth USB devices into the kernel or say M to compile it as module (btusb). diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c index 95ae9ba5661..6a010681ecf 100644 --- a/drivers/bluetooth/btusb.c +++ b/drivers/bluetooth/btusb.c @@ -2,7 +2,7 @@ * * Generic Bluetooth USB driver * - * Copyright (C) 2005-2007 Marcel Holtmann + * Copyright (C) 2005-2008 Marcel Holtmann * * * This program is free software; you can redistribute it and/or modify @@ -41,7 +41,7 @@ #define BT_DBG(D...) #endif -#define VERSION "0.2" +#define VERSION "0.3" static int ignore_dga; static int ignore_csr; @@ -160,12 +160,16 @@ static struct usb_device_id blacklist_table[] = { { } /* Terminating entry */ }; +#define BTUSB_MAX_ISOC_FRAMES 10 + #define BTUSB_INTR_RUNNING 0 #define BTUSB_BULK_RUNNING 1 +#define BTUSB_ISOC_RUNNING 2 struct btusb_data { struct hci_dev *hdev; struct usb_device *udev; + struct usb_interface *isoc; spinlock_t lock; @@ -176,10 +180,15 @@ struct btusb_data { struct usb_anchor tx_anchor; struct usb_anchor intr_anchor; struct usb_anchor bulk_anchor; + struct usb_anchor isoc_anchor; struct usb_endpoint_descriptor *intr_ep; struct usb_endpoint_descriptor *bulk_tx_ep; struct usb_endpoint_descriptor *bulk_rx_ep; + struct usb_endpoint_descriptor *isoc_tx_ep; + struct usb_endpoint_descriptor *isoc_rx_ep; + + int isoc_altsetting; }; static void btusb_intr_complete(struct urb *urb) @@ -195,6 +204,8 @@ static void btusb_intr_complete(struct urb *urb) return; if (urb->status == 0) { + hdev->stat.byte_rx += urb->actual_length; + if (hci_recv_fragment(hdev, HCI_EVENT_PKT, urb->transfer_buffer, urb->actual_length) < 0) { @@ -216,7 +227,7 @@ static void btusb_intr_complete(struct urb *urb) } } -static inline int btusb_submit_intr_urb(struct hci_dev *hdev) +static int btusb_submit_intr_urb(struct hci_dev *hdev) { struct btusb_data *data = hdev->driver_data; struct urb *urb; @@ -226,6 +237,9 @@ static inline int btusb_submit_intr_urb(struct hci_dev *hdev) BT_DBG("%s", hdev->name); + if (!data->intr_ep) + return -ENODEV; + urb = usb_alloc_urb(0, GFP_ATOMIC); if (!urb) return -ENOMEM; @@ -274,6 +288,8 @@ static void btusb_bulk_complete(struct urb *urb) return; if (urb->status == 0) { + hdev->stat.byte_rx += urb->actual_length; + if (hci_recv_fragment(hdev, HCI_ACLDATA_PKT, urb->transfer_buffer, urb->actual_length) < 0) { @@ -295,7 +311,7 @@ static void btusb_bulk_complete(struct urb *urb) } } -static inline int btusb_submit_bulk_urb(struct hci_dev *hdev) +static int btusb_submit_bulk_urb(struct hci_dev *hdev) { struct btusb_data *data = hdev->driver_data; struct urb *urb; @@ -305,6 +321,9 @@ static inline int btusb_submit_bulk_urb(struct hci_dev *hdev) BT_DBG("%s", hdev->name); + if (!data->bulk_rx_ep) + return -ENODEV; + urb = usb_alloc_urb(0, GFP_KERNEL); if (!urb) return -ENOMEM; @@ -339,6 +358,127 @@ static inline int btusb_submit_bulk_urb(struct hci_dev *hdev) return err; } +static void btusb_isoc_complete(struct urb *urb) +{ + struct hci_dev *hdev = urb->context; + struct btusb_data *data = hdev->driver_data; + int i, err; + + BT_DBG("%s urb %p status %d count %d", hdev->name, + urb, urb->status, urb->actual_length); + + if (!test_bit(HCI_RUNNING, &hdev->flags)) + return; + + if (urb->status == 0) { + for (i = 0; i < urb->number_of_packets; i++) { + unsigned int offset = urb->iso_frame_desc[i].offset; + unsigned int length = urb->iso_frame_desc[i].actual_length; + + if (urb->iso_frame_desc[i].status) + continue; + + hdev->stat.byte_rx += length; + + if (hci_recv_fragment(hdev, HCI_SCODATA_PKT, + urb->transfer_buffer + offset, + length) < 0) { + BT_ERR("%s corrupted SCO packet", hdev->name); + hdev->stat.err_rx++; + } + } + } + + if (!test_bit(BTUSB_ISOC_RUNNING, &data->flags)) + return; + + usb_anchor_urb(urb, &data->isoc_anchor); + + err = usb_submit_urb(urb, GFP_ATOMIC); + if (err < 0) { + BT_ERR("%s urb %p failed to resubmit (%d)", + hdev->name, urb, -err); + usb_unanchor_urb(urb); + } +} + +static void inline __fill_isoc_descriptor(struct urb *urb, int len, int mtu) +{ + int i, offset = 0; + + BT_DBG("len %d mtu %d", len, mtu); + + for (i = 0; i < BTUSB_MAX_ISOC_FRAMES && len >= mtu; + i++, offset += mtu, len -= mtu) { + urb->iso_frame_desc[i].offset = offset; + urb->iso_frame_desc[i].length = mtu; + } + + if (len && i < BTUSB_MAX_ISOC_FRAMES) { + urb->iso_frame_desc[i].offset = offset; + urb->iso_frame_desc[i].length = len; + i++; + } + + urb->number_of_packets = i; +} + +static int btusb_submit_isoc_urb(struct hci_dev *hdev) +{ + struct btusb_data *data = hdev->driver_data; + struct urb *urb; + unsigned char *buf; + unsigned int pipe; + int err, size; + + BT_DBG("%s", hdev->name); + + if (!data->isoc_rx_ep) + return -ENODEV; + + urb = usb_alloc_urb(BTUSB_MAX_ISOC_FRAMES, GFP_KERNEL); + if (!urb) + return -ENOMEM; + + size = le16_to_cpu(data->isoc_rx_ep->wMaxPacketSize) * + BTUSB_MAX_ISOC_FRAMES; + + buf = kmalloc(size, GFP_KERNEL); + if (!buf) { + usb_free_urb(urb); + return -ENOMEM; + } + + pipe = usb_rcvisocpipe(data->udev, data->isoc_rx_ep->bEndpointAddress); + + urb->dev = data->udev; + urb->pipe = pipe; + urb->context = hdev; + urb->complete = btusb_isoc_complete; + urb->interval = data->isoc_rx_ep->bInterval; + + urb->transfer_flags = URB_FREE_BUFFER | URB_ISO_ASAP; + urb->transfer_buffer = buf; + urb->transfer_buffer_length = size; + + __fill_isoc_descriptor(urb, size, + le16_to_cpu(data->isoc_rx_ep->wMaxPacketSize)); + + usb_anchor_urb(urb, &data->isoc_anchor); + + err = usb_submit_urb(urb, GFP_KERNEL); + if (err < 0) { + BT_ERR("%s urb %p submission failed (%d)", + hdev->name, urb, -err); + usb_unanchor_urb(urb); + kfree(buf); + } + + usb_free_urb(urb); + + return err; +} + static void btusb_tx_complete(struct urb *urb) { struct sk_buff *skb = urb->context; @@ -392,6 +532,9 @@ static int btusb_close(struct hci_dev *hdev) if (!test_and_clear_bit(HCI_RUNNING, &hdev->flags)) return 0; + clear_bit(BTUSB_ISOC_RUNNING, &data->flags); + usb_kill_anchored_urbs(&data->intr_anchor); + clear_bit(BTUSB_BULK_RUNNING, &data->flags); usb_kill_anchored_urbs(&data->bulk_anchor); @@ -453,6 +596,9 @@ static int btusb_send_frame(struct sk_buff *skb) break; case HCI_ACLDATA_PKT: + if (!data->bulk_tx_ep || hdev->conn_hash.acl_num < 1) + return -ENODEV; + urb = usb_alloc_urb(0, GFP_ATOMIC); if (!urb) return -ENOMEM; @@ -467,9 +613,31 @@ static int btusb_send_frame(struct sk_buff *skb) break; case HCI_SCODATA_PKT: + if (!data->isoc_tx_ep || hdev->conn_hash.sco_num < 1) + return -ENODEV; + + urb = usb_alloc_urb(BTUSB_MAX_ISOC_FRAMES, GFP_ATOMIC); + if (!urb) + return -ENOMEM; + + pipe = usb_sndisocpipe(data->udev, + data->isoc_tx_ep->bEndpointAddress); + + urb->dev = data->udev; + urb->pipe = pipe; + urb->context = skb; + urb->complete = btusb_tx_complete; + urb->interval = data->isoc_tx_ep->bInterval; + + urb->transfer_flags = URB_ISO_ASAP; + urb->transfer_buffer = skb->data; + urb->transfer_buffer_length = skb->len; + + __fill_isoc_descriptor(urb, skb->len, + le16_to_cpu(data->isoc_tx_ep->wMaxPacketSize)); + hdev->stat.sco_tx++; - kfree_skb(skb); - return 0; + break; default: return -EILSEQ; @@ -508,22 +676,86 @@ static void btusb_notify(struct hci_dev *hdev, unsigned int evt) schedule_work(&data->work); } +static int inline __set_isoc_interface(struct hci_dev *hdev, int altsetting) +{ + struct btusb_data *data = hdev->driver_data; + struct usb_interface *intf = data->isoc; + struct usb_endpoint_descriptor *ep_desc; + int i, err; + + if (!data->isoc) + return -ENODEV; + + err = usb_set_interface(data->udev, 1, altsetting); + if (err < 0) { + BT_ERR("%s setting interface failed (%d)", hdev->name, -err); + return err; + } + + data->isoc_altsetting = altsetting; + + data->isoc_tx_ep = NULL; + data->isoc_rx_ep = NULL; + + for (i = 0; i < intf->cur_altsetting->desc.bNumEndpoints; i++) { + ep_desc = &intf->cur_altsetting->endpoint[i].desc; + + if (!data->isoc_tx_ep && usb_endpoint_is_isoc_out(ep_desc)) { + data->isoc_tx_ep = ep_desc; + continue; + } + + if (!data->isoc_rx_ep && usb_endpoint_is_isoc_in(ep_desc)) { + data->isoc_rx_ep = ep_desc; + continue; + } + } + + if (!data->isoc_tx_ep || !data->isoc_rx_ep) { + BT_ERR("%s invalid SCO descriptors", hdev->name); + return -ENODEV; + } + + return 0; +} + static void btusb_work(struct work_struct *work) { struct btusb_data *data = container_of(work, struct btusb_data, work); struct hci_dev *hdev = data->hdev; - if (hdev->conn_hash.acl_num == 0) { + if (hdev->conn_hash.acl_num > 0) { + if (!test_and_set_bit(BTUSB_BULK_RUNNING, &data->flags)) { + if (btusb_submit_bulk_urb(hdev) < 0) + clear_bit(BTUSB_BULK_RUNNING, &data->flags); + else + btusb_submit_bulk_urb(hdev); + } + } else { clear_bit(BTUSB_BULK_RUNNING, &data->flags); usb_kill_anchored_urbs(&data->bulk_anchor); - return; } - if (!test_and_set_bit(BTUSB_BULK_RUNNING, &data->flags)) { - if (btusb_submit_bulk_urb(hdev) < 0) - clear_bit(BTUSB_BULK_RUNNING, &data->flags); - else - btusb_submit_bulk_urb(hdev); + if (hdev->conn_hash.sco_num > 0) { + if (data->isoc_altsetting != 2) { + clear_bit(BTUSB_ISOC_RUNNING, &data->flags); + usb_kill_anchored_urbs(&data->isoc_anchor); + + if (__set_isoc_interface(hdev, 2) < 0) + return; + } + + if (!test_and_set_bit(BTUSB_ISOC_RUNNING, &data->flags)) { + if (btusb_submit_isoc_urb(hdev) < 0) + clear_bit(BTUSB_ISOC_RUNNING, &data->flags); + else + btusb_submit_isoc_urb(hdev); + } + } else { + clear_bit(BTUSB_ISOC_RUNNING, &data->flags); + usb_kill_anchored_urbs(&data->isoc_anchor); + + __set_isoc_interface(hdev, 0); } } @@ -597,6 +829,7 @@ static int btusb_probe(struct usb_interface *intf, init_usb_anchor(&data->tx_anchor); init_usb_anchor(&data->intr_anchor); init_usb_anchor(&data->bulk_anchor); + init_usb_anchor(&data->isoc_anchor); hdev = hci_alloc_dev(); if (!hdev) { @@ -620,6 +853,9 @@ static int btusb_probe(struct usb_interface *intf, hdev->owner = THIS_MODULE; + /* interface numbers are hardcoded in the spec */ + data->isoc = usb_ifnum_to_if(data->udev, 1); + if (reset || id->driver_info & BTUSB_RESET) set_bit(HCI_QUIRK_RESET_ON_INIT, &hdev->quirks); @@ -628,11 +864,16 @@ static int btusb_probe(struct usb_interface *intf, set_bit(HCI_QUIRK_FIXUP_BUFFER_SIZE, &hdev->quirks); } + if (id->driver_info & BTUSB_BROKEN_ISOC) + data->isoc = NULL; + if (id->driver_info & BTUSB_SNIFFER) { - struct usb_device *udev = interface_to_usbdev(intf); + struct usb_device *udev = data->udev; if (le16_to_cpu(udev->descriptor.bcdDevice) > 0x997) set_bit(HCI_QUIRK_RAW_DEVICE, &hdev->quirks); + + data->isoc = NULL; } if (id->driver_info & BTUSB_BCM92035) { @@ -646,6 +887,16 @@ static int btusb_probe(struct usb_interface *intf, } } + if (data->isoc) { + err = usb_driver_claim_interface(&btusb_driver, + data->isoc, NULL); + if (err < 0) { + hci_free_dev(hdev); + kfree(data); + return err; + } + } + err = hci_register_dev(hdev); if (err < 0) { hci_free_dev(hdev); @@ -670,6 +921,9 @@ static void btusb_disconnect(struct usb_interface *intf) hdev = data->hdev; + if (data->isoc) + usb_driver_release_interface(&btusb_driver, data->isoc); + usb_set_intfdata(intf, NULL); hci_unregister_dev(hdev); -- GitLab From 90855d7b725d764d6d70503bcc1b494cf10ddc98 Mon Sep 17 00:00:00 2001 From: Marcel Holtmann Date: Mon, 18 Aug 2008 13:23:53 +0200 Subject: [PATCH 545/750] [Bluetooth] Fix userspace breakage due missing class links The Bluetooth adapters and connections are best presented via a class in sysfs. The removal of the links inside the Bluetooth class broke assumptions by userspace programs on how to find attached adapters. This patch creates adapters and connections as part of the Bluetooth class, but it uses different device types to distinguish them. The userspace programs can now easily navigate in the sysfs device tree. The unused platform device and bus have been removed to keep the code simple and clean. Signed-off-by: Marcel Holtmann --- net/bluetooth/hci_sysfs.c | 376 +++++++++++++++++++------------------- 1 file changed, 189 insertions(+), 187 deletions(-) diff --git a/net/bluetooth/hci_sysfs.c b/net/bluetooth/hci_sysfs.c index c85bf8f678d..f4f6615cad9 100644 --- a/net/bluetooth/hci_sysfs.c +++ b/net/bluetooth/hci_sysfs.c @@ -3,8 +3,6 @@ #include #include -#include - #include #include @@ -12,10 +10,164 @@ #undef BT_DBG #define BT_DBG(D...) #endif + +struct class *bt_class = NULL; +EXPORT_SYMBOL_GPL(bt_class); + static struct workqueue_struct *btaddconn; static struct workqueue_struct *btdelconn; -static inline char *typetostr(int type) +static inline char *link_typetostr(int type) +{ + switch (type) { + case ACL_LINK: + return "ACL"; + case SCO_LINK: + return "SCO"; + case ESCO_LINK: + return "eSCO"; + default: + return "UNKNOWN"; + } +} + +static ssize_t show_link_type(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct hci_conn *conn = dev_get_drvdata(dev); + return sprintf(buf, "%s\n", link_typetostr(conn->type)); +} + +static ssize_t show_link_address(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct hci_conn *conn = dev_get_drvdata(dev); + bdaddr_t bdaddr; + baswap(&bdaddr, &conn->dst); + return sprintf(buf, "%s\n", batostr(&bdaddr)); +} + +static ssize_t show_link_features(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct hci_conn *conn = dev_get_drvdata(dev); + + return sprintf(buf, "0x%02x%02x%02x%02x%02x%02x%02x%02x\n", + conn->features[0], conn->features[1], + conn->features[2], conn->features[3], + conn->features[4], conn->features[5], + conn->features[6], conn->features[7]); +} + +#define LINK_ATTR(_name,_mode,_show,_store) \ +struct device_attribute link_attr_##_name = __ATTR(_name,_mode,_show,_store) + +static LINK_ATTR(type, S_IRUGO, show_link_type, NULL); +static LINK_ATTR(address, S_IRUGO, show_link_address, NULL); +static LINK_ATTR(features, S_IRUGO, show_link_features, NULL); + +static struct attribute *bt_link_attrs[] = { + &link_attr_type.attr, + &link_attr_address.attr, + &link_attr_features.attr, + NULL +}; + +static struct attribute_group bt_link_group = { + .attrs = bt_link_attrs, +}; + +static struct attribute_group *bt_link_groups[] = { + &bt_link_group, + NULL +}; + +static void bt_link_release(struct device *dev) +{ + void *data = dev_get_drvdata(dev); + kfree(data); +} + +static struct device_type bt_link = { + .name = "link", + .groups = bt_link_groups, + .release = bt_link_release, +}; + +static void add_conn(struct work_struct *work) +{ + struct hci_conn *conn = container_of(work, struct hci_conn, work); + + flush_workqueue(btdelconn); + + if (device_add(&conn->dev) < 0) { + BT_ERR("Failed to register connection device"); + return; + } +} + +void hci_conn_add_sysfs(struct hci_conn *conn) +{ + struct hci_dev *hdev = conn->hdev; + + BT_DBG("conn %p", conn); + + conn->dev.type = &bt_link; + conn->dev.class = bt_class; + conn->dev.parent = &hdev->dev; + + snprintf(conn->dev.bus_id, BUS_ID_SIZE, "%s:%d", + hdev->name, conn->handle); + + dev_set_drvdata(&conn->dev, conn); + + device_initialize(&conn->dev); + + INIT_WORK(&conn->work, add_conn); + + queue_work(btaddconn, &conn->work); +} + +/* + * The rfcomm tty device will possibly retain even when conn + * is down, and sysfs doesn't support move zombie device, + * so we should move the device before conn device is destroyed. + */ +static int __match_tty(struct device *dev, void *data) +{ + return !strncmp(dev->bus_id, "rfcomm", 6); +} + +static void del_conn(struct work_struct *work) +{ + struct hci_conn *conn = container_of(work, struct hci_conn, work); + struct hci_dev *hdev = conn->hdev; + + while (1) { + struct device *dev; + + dev = device_find_child(&conn->dev, NULL, __match_tty); + if (!dev) + break; + device_move(dev, NULL); + put_device(dev); + } + + device_del(&conn->dev); + put_device(&conn->dev); + hci_dev_put(hdev); +} + +void hci_conn_del_sysfs(struct hci_conn *conn) +{ + BT_DBG("conn %p", conn); + + if (!device_is_registered(&conn->dev)) + return; + + INIT_WORK(&conn->work, del_conn); + + queue_work(btdelconn, &conn->work); +} + +static inline char *host_typetostr(int type) { switch (type) { case HCI_VIRTUAL: @@ -40,7 +192,7 @@ static inline char *typetostr(int type) static ssize_t show_type(struct device *dev, struct device_attribute *attr, char *buf) { struct hci_dev *hdev = dev_get_drvdata(dev); - return sprintf(buf, "%s\n", typetostr(hdev->type)); + return sprintf(buf, "%s\n", host_typetostr(hdev->type)); } static ssize_t show_name(struct device *dev, struct device_attribute *attr, char *buf) @@ -221,183 +373,62 @@ static DEVICE_ATTR(sniff_max_interval, S_IRUGO | S_IWUSR, static DEVICE_ATTR(sniff_min_interval, S_IRUGO | S_IWUSR, show_sniff_min_interval, store_sniff_min_interval); -static struct device_attribute *bt_attrs[] = { - &dev_attr_type, - &dev_attr_name, - &dev_attr_class, - &dev_attr_address, - &dev_attr_features, - &dev_attr_manufacturer, - &dev_attr_hci_version, - &dev_attr_hci_revision, - &dev_attr_inquiry_cache, - &dev_attr_idle_timeout, - &dev_attr_sniff_max_interval, - &dev_attr_sniff_min_interval, +static struct attribute *bt_host_attrs[] = { + &dev_attr_type.attr, + &dev_attr_name.attr, + &dev_attr_class.attr, + &dev_attr_address.attr, + &dev_attr_features.attr, + &dev_attr_manufacturer.attr, + &dev_attr_hci_version.attr, + &dev_attr_hci_revision.attr, + &dev_attr_inquiry_cache.attr, + &dev_attr_idle_timeout.attr, + &dev_attr_sniff_max_interval.attr, + &dev_attr_sniff_min_interval.attr, NULL }; -static ssize_t show_conn_type(struct device *dev, struct device_attribute *attr, char *buf) -{ - struct hci_conn *conn = dev_get_drvdata(dev); - return sprintf(buf, "%s\n", conn->type == ACL_LINK ? "ACL" : "SCO"); -} - -static ssize_t show_conn_address(struct device *dev, struct device_attribute *attr, char *buf) -{ - struct hci_conn *conn = dev_get_drvdata(dev); - bdaddr_t bdaddr; - baswap(&bdaddr, &conn->dst); - return sprintf(buf, "%s\n", batostr(&bdaddr)); -} - -static ssize_t show_conn_features(struct device *dev, struct device_attribute *attr, char *buf) -{ - struct hci_conn *conn = dev_get_drvdata(dev); - - return sprintf(buf, "0x%02x%02x%02x%02x%02x%02x%02x%02x\n", - conn->features[0], conn->features[1], - conn->features[2], conn->features[3], - conn->features[4], conn->features[5], - conn->features[6], conn->features[7]); -} - -#define CONN_ATTR(_name,_mode,_show,_store) \ -struct device_attribute conn_attr_##_name = __ATTR(_name,_mode,_show,_store) - -static CONN_ATTR(type, S_IRUGO, show_conn_type, NULL); -static CONN_ATTR(address, S_IRUGO, show_conn_address, NULL); -static CONN_ATTR(features, S_IRUGO, show_conn_features, NULL); - -static struct device_attribute *conn_attrs[] = { - &conn_attr_type, - &conn_attr_address, - &conn_attr_features, - NULL +static struct attribute_group bt_host_group = { + .attrs = bt_host_attrs, }; -struct class *bt_class = NULL; -EXPORT_SYMBOL_GPL(bt_class); - -static struct bus_type bt_bus = { - .name = "bluetooth", +static struct attribute_group *bt_host_groups[] = { + &bt_host_group, + NULL }; -static struct platform_device *bt_platform; - -static void bt_release(struct device *dev) +static void bt_host_release(struct device *dev) { void *data = dev_get_drvdata(dev); kfree(data); } -static void add_conn(struct work_struct *work) -{ - struct hci_conn *conn = container_of(work, struct hci_conn, work); - int i; - - flush_workqueue(btdelconn); - - if (device_add(&conn->dev) < 0) { - BT_ERR("Failed to register connection device"); - return; - } - - for (i = 0; conn_attrs[i]; i++) - if (device_create_file(&conn->dev, conn_attrs[i]) < 0) - BT_ERR("Failed to create connection attribute"); -} - -void hci_conn_add_sysfs(struct hci_conn *conn) -{ - struct hci_dev *hdev = conn->hdev; - - BT_DBG("conn %p", conn); - - conn->dev.bus = &bt_bus; - conn->dev.parent = &hdev->dev; - - conn->dev.release = bt_release; - - snprintf(conn->dev.bus_id, BUS_ID_SIZE, "%s:%d", - hdev->name, conn->handle); - - dev_set_drvdata(&conn->dev, conn); - - device_initialize(&conn->dev); - - INIT_WORK(&conn->work, add_conn); - - queue_work(btaddconn, &conn->work); -} - -/* - * The rfcomm tty device will possibly retain even when conn - * is down, and sysfs doesn't support move zombie device, - * so we should move the device before conn device is destroyed. - */ -static int __match_tty(struct device *dev, void *data) -{ - return !strncmp(dev->bus_id, "rfcomm", 6); -} - -static void del_conn(struct work_struct *work) -{ - struct hci_conn *conn = container_of(work, struct hci_conn, work); - struct hci_dev *hdev = conn->hdev; - - while (1) { - struct device *dev; - - dev = device_find_child(&conn->dev, NULL, __match_tty); - if (!dev) - break; - device_move(dev, NULL); - put_device(dev); - } - - device_del(&conn->dev); - put_device(&conn->dev); - hci_dev_put(hdev); -} - -void hci_conn_del_sysfs(struct hci_conn *conn) -{ - BT_DBG("conn %p", conn); - - if (!device_is_registered(&conn->dev)) - return; - - INIT_WORK(&conn->work, del_conn); - - queue_work(btdelconn, &conn->work); -} +static struct device_type bt_host = { + .name = "host", + .groups = bt_host_groups, + .release = bt_host_release, +}; int hci_register_sysfs(struct hci_dev *hdev) { struct device *dev = &hdev->dev; - unsigned int i; int err; BT_DBG("%p name %s type %d", hdev, hdev->name, hdev->type); - dev->bus = &bt_bus; + dev->type = &bt_host; + dev->class = bt_class; dev->parent = hdev->parent; strlcpy(dev->bus_id, hdev->name, BUS_ID_SIZE); - dev->release = bt_release; - dev_set_drvdata(dev, hdev); err = device_register(dev); if (err < 0) return err; - for (i = 0; bt_attrs[i]; i++) - if (device_create_file(dev, bt_attrs[i]) < 0) - BT_ERR("Failed to create device attribute"); - return 0; } @@ -410,59 +441,30 @@ void hci_unregister_sysfs(struct hci_dev *hdev) int __init bt_sysfs_init(void) { - int err; - btaddconn = create_singlethread_workqueue("btaddconn"); - if (!btaddconn) { - err = -ENOMEM; - goto out; - } + if (!btaddconn) + return -ENOMEM; btdelconn = create_singlethread_workqueue("btdelconn"); if (!btdelconn) { - err = -ENOMEM; - goto out_del; - } - - bt_platform = platform_device_register_simple("bluetooth", -1, NULL, 0); - if (IS_ERR(bt_platform)) { - err = PTR_ERR(bt_platform); - goto out_platform; + destroy_workqueue(btaddconn); + return -ENOMEM; } - err = bus_register(&bt_bus); - if (err < 0) - goto out_bus; - bt_class = class_create(THIS_MODULE, "bluetooth"); if (IS_ERR(bt_class)) { - err = PTR_ERR(bt_class); - goto out_class; + destroy_workqueue(btdelconn); + destroy_workqueue(btaddconn); + return PTR_ERR(bt_class); } return 0; - -out_class: - bus_unregister(&bt_bus); -out_bus: - platform_device_unregister(bt_platform); -out_platform: - destroy_workqueue(btdelconn); -out_del: - destroy_workqueue(btaddconn); -out: - return err; } void bt_sysfs_cleanup(void) { destroy_workqueue(btaddconn); - destroy_workqueue(btdelconn); class_destroy(bt_class); - - bus_unregister(&bt_bus); - - platform_device_unregister(bt_platform); } -- GitLab From 63fbd24e5102eecfc9d049ed7f4be7f9a25f814f Mon Sep 17 00:00:00 2001 From: Marcel Holtmann Date: Mon, 18 Aug 2008 13:23:53 +0200 Subject: [PATCH 546/750] [Bluetooth] Consolidate maintainers information The Bluetooth entries for the MAINTAINERS file are a little bit too much. Consolidate them into two entries. One for Bluetooth drivers and another one for the Bluetooth subsystem. Also the MODULE_AUTHOR should indicate the current maintainer of the module and actually not the original author. Fix all Bluetooth modules to provide current maintainer information. Signed-off-by: Marcel Holtmann --- MAINTAINERS | 87 +++-------------------------------- drivers/bluetooth/bt3c_cs.c | 2 +- drivers/bluetooth/hci_ldisc.c | 2 +- drivers/bluetooth/hci_usb.c | 2 +- drivers/bluetooth/hci_vhci.c | 2 +- net/bluetooth/af_bluetooth.c | 2 +- net/bluetooth/bnep/core.c | 2 +- net/bluetooth/l2cap.c | 2 +- net/bluetooth/rfcomm/core.c | 2 +- net/bluetooth/sco.c | 2 +- 10 files changed, 15 insertions(+), 90 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index af6aa4e4b39..2676f9a1fee 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -936,94 +936,19 @@ M: joern@lazybastard.org L: linux-mtd@lists.infradead.org S: Maintained -BLUETOOTH SUBSYSTEM +BLUETOOTH DRIVERS P: Marcel Holtmann M: marcel@holtmann.org -P: Maxim Krasnyansky -M: maxk@qualcomm.com L: linux-bluetooth@vger.kernel.org -W: http://bluez.sf.net -W: http://www.bluez.org -W: http://www.holtmann.org/linux/bluetooth/ -T: git kernel.org:/pub/scm/linux/kernel/git/holtmann/bluetooth-2.6.git -S: Maintained - -BLUETOOTH RFCOMM LAYER -P: Marcel Holtmann -M: marcel@holtmann.org -P: Maxim Krasnyansky -M: maxk@qualcomm.com -S: Maintained - -BLUETOOTH BNEP LAYER -P: Marcel Holtmann -M: marcel@holtmann.org -P: Maxim Krasnyansky -M: maxk@qualcomm.com -S: Maintained - -BLUETOOTH CMTP LAYER -P: Marcel Holtmann -M: marcel@holtmann.org +W: http://www.bluez.org/ S: Maintained -BLUETOOTH HIDP LAYER -P: Marcel Holtmann -M: marcel@holtmann.org -S: Maintained - -BLUETOOTH HCI UART DRIVER -P: Marcel Holtmann -M: marcel@holtmann.org -P: Maxim Krasnyansky -M: maxk@qualcomm.com -S: Maintained - -BLUETOOTH HCI USB DRIVER -P: Marcel Holtmann -M: marcel@holtmann.org -P: Maxim Krasnyansky -M: maxk@qualcomm.com -S: Maintained - -BLUETOOTH HCI BCM203X DRIVER -P: Marcel Holtmann -M: marcel@holtmann.org -S: Maintained - -BLUETOOTH HCI BPA10X DRIVER -P: Marcel Holtmann -M: marcel@holtmann.org -S: Maintained - -BLUETOOTH HCI BFUSB DRIVER -P: Marcel Holtmann -M: marcel@holtmann.org -S: Maintained - -BLUETOOTH HCI DTL1 DRIVER -P: Marcel Holtmann -M: marcel@holtmann.org -S: Maintained - -BLUETOOTH HCI BLUECARD DRIVER -P: Marcel Holtmann -M: marcel@holtmann.org -S: Maintained - -BLUETOOTH HCI BT3C DRIVER -P: Marcel Holtmann -M: marcel@holtmann.org -S: Maintained - -BLUETOOTH HCI BTUART DRIVER +BLUETOOTH SUBSYSTEM P: Marcel Holtmann M: marcel@holtmann.org -S: Maintained - -BLUETOOTH HCI VHCI DRIVER -P: Maxim Krasnyansky -M: maxk@qualcomm.com +L: linux-bluetooth@vger.kernel.org +W: http://www.bluez.org/ +T: git kernel.org:/pub/scm/linux/kernel/git/holtmann/bluetooth-2.6.git S: Maintained BONDING DRIVER diff --git a/drivers/bluetooth/bt3c_cs.c b/drivers/bluetooth/bt3c_cs.c index 593b7c59503..27058477cc8 100644 --- a/drivers/bluetooth/bt3c_cs.c +++ b/drivers/bluetooth/bt3c_cs.c @@ -60,7 +60,7 @@ /* ======================== Module parameters ======================== */ -MODULE_AUTHOR("Marcel Holtmann , Jose Orlando Pereira "); +MODULE_AUTHOR("Marcel Holtmann "); MODULE_DESCRIPTION("Bluetooth driver for the 3Com Bluetooth PCMCIA card"); MODULE_LICENSE("GPL"); MODULE_FIRMWARE("BT3CPCC.bin"); diff --git a/drivers/bluetooth/hci_ldisc.c b/drivers/bluetooth/hci_ldisc.c index 69df187d74c..8dfcf77cb71 100644 --- a/drivers/bluetooth/hci_ldisc.c +++ b/drivers/bluetooth/hci_ldisc.c @@ -577,7 +577,7 @@ module_exit(hci_uart_exit); module_param(reset, bool, 0644); MODULE_PARM_DESC(reset, "Send HCI reset command on initialization"); -MODULE_AUTHOR("Maxim Krasnyansky , Marcel Holtmann "); +MODULE_AUTHOR("Marcel Holtmann "); MODULE_DESCRIPTION("Bluetooth HCI UART driver ver " VERSION); MODULE_VERSION(VERSION); MODULE_LICENSE("GPL"); diff --git a/drivers/bluetooth/hci_usb.c b/drivers/bluetooth/hci_usb.c index e397572bf57..3c453924f83 100644 --- a/drivers/bluetooth/hci_usb.c +++ b/drivers/bluetooth/hci_usb.c @@ -1130,7 +1130,7 @@ module_param(isoc, int, 0644); MODULE_PARM_DESC(isoc, "Set isochronous transfers for SCO over HCI support"); #endif -MODULE_AUTHOR("Maxim Krasnyansky , Marcel Holtmann "); +MODULE_AUTHOR("Marcel Holtmann "); MODULE_DESCRIPTION("Bluetooth HCI USB driver ver " VERSION); MODULE_VERSION(VERSION); MODULE_LICENSE("GPL"); diff --git a/drivers/bluetooth/hci_vhci.c b/drivers/bluetooth/hci_vhci.c index d97700aa54a..7320a71b636 100644 --- a/drivers/bluetooth/hci_vhci.c +++ b/drivers/bluetooth/hci_vhci.c @@ -377,7 +377,7 @@ module_exit(vhci_exit); module_param(minor, int, 0444); MODULE_PARM_DESC(minor, "Miscellaneous minor device number"); -MODULE_AUTHOR("Maxim Krasnyansky , Marcel Holtmann "); +MODULE_AUTHOR("Marcel Holtmann "); MODULE_DESCRIPTION("Bluetooth virtual HCI driver ver " VERSION); MODULE_VERSION(VERSION); MODULE_LICENSE("GPL"); diff --git a/net/bluetooth/af_bluetooth.c b/net/bluetooth/af_bluetooth.c index 4e59df5f8e0..1edfdf4c095 100644 --- a/net/bluetooth/af_bluetooth.c +++ b/net/bluetooth/af_bluetooth.c @@ -456,7 +456,7 @@ static void __exit bt_exit(void) subsys_initcall(bt_init); module_exit(bt_exit); -MODULE_AUTHOR("Maxim Krasnyansky , Marcel Holtmann "); +MODULE_AUTHOR("Marcel Holtmann "); MODULE_DESCRIPTION("Bluetooth Core ver " VERSION); MODULE_VERSION(VERSION); MODULE_LICENSE("GPL"); diff --git a/net/bluetooth/bnep/core.c b/net/bluetooth/bnep/core.c index 12bba6207a8..80ba30cf4b6 100644 --- a/net/bluetooth/bnep/core.c +++ b/net/bluetooth/bnep/core.c @@ -736,7 +736,7 @@ MODULE_PARM_DESC(compress_src, "Compress sources headers"); module_param(compress_dst, bool, 0644); MODULE_PARM_DESC(compress_dst, "Compress destination headers"); -MODULE_AUTHOR("David Libault , Maxim Krasnyansky "); +MODULE_AUTHOR("Marcel Holtmann "); MODULE_DESCRIPTION("Bluetooth BNEP ver " VERSION); MODULE_VERSION(VERSION); MODULE_LICENSE("GPL"); diff --git a/net/bluetooth/l2cap.c b/net/bluetooth/l2cap.c index c1239852834..3396d5bdef1 100644 --- a/net/bluetooth/l2cap.c +++ b/net/bluetooth/l2cap.c @@ -2516,7 +2516,7 @@ EXPORT_SYMBOL(l2cap_load); module_init(l2cap_init); module_exit(l2cap_exit); -MODULE_AUTHOR("Maxim Krasnyansky , Marcel Holtmann "); +MODULE_AUTHOR("Marcel Holtmann "); MODULE_DESCRIPTION("Bluetooth L2CAP ver " VERSION); MODULE_VERSION(VERSION); MODULE_LICENSE("GPL"); diff --git a/net/bluetooth/rfcomm/core.c b/net/bluetooth/rfcomm/core.c index 6cfc7ba611b..ba537fae0a4 100644 --- a/net/bluetooth/rfcomm/core.c +++ b/net/bluetooth/rfcomm/core.c @@ -2115,7 +2115,7 @@ MODULE_PARM_DESC(channel_mtu, "Default MTU for the RFCOMM channel"); module_param(l2cap_mtu, uint, 0644); MODULE_PARM_DESC(l2cap_mtu, "Default MTU for the L2CAP connection"); -MODULE_AUTHOR("Maxim Krasnyansky , Marcel Holtmann "); +MODULE_AUTHOR("Marcel Holtmann "); MODULE_DESCRIPTION("Bluetooth RFCOMM ver " VERSION); MODULE_VERSION(VERSION); MODULE_LICENSE("GPL"); diff --git a/net/bluetooth/sco.c b/net/bluetooth/sco.c index 8cda4987486..a16011fedc1 100644 --- a/net/bluetooth/sco.c +++ b/net/bluetooth/sco.c @@ -1002,7 +1002,7 @@ module_exit(sco_exit); module_param(disable_esco, bool, 0644); MODULE_PARM_DESC(disable_esco, "Disable eSCO connection creation"); -MODULE_AUTHOR("Maxim Krasnyansky , Marcel Holtmann "); +MODULE_AUTHOR("Marcel Holtmann "); MODULE_DESCRIPTION("Bluetooth SCO ver " VERSION); MODULE_VERSION(VERSION); MODULE_LICENSE("GPL"); -- GitLab From faa64c93ae3fa3b3c97e502e60ce8430ab61cd9d Mon Sep 17 00:00:00 2001 From: Russell King Date: Tue, 5 Aug 2008 10:36:00 +0100 Subject: [PATCH 547/750] [ARM] fix impd1.c build warning CC arch/arm/mach-integrator/impd1.o arch/arm/mach-integrator/impd1.c: In function `impd1_probe': arch/arm/mach-integrator/impd1.c:408: warning: too few arguments for format Signed-off-by: Russell King --- arch/arm/mach-integrator/impd1.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-integrator/impd1.c b/arch/arm/mach-integrator/impd1.c index 0a7b3267c8d..3c8383dbe9e 100644 --- a/arch/arm/mach-integrator/impd1.c +++ b/arch/arm/mach-integrator/impd1.c @@ -405,7 +405,7 @@ static int impd1_probe(struct lm_device *dev) ret = amba_device_register(d, &dev->resource); if (ret) { - dev_err(&d->dev, "unable to register device: %d\n"); + dev_err(&d->dev, "unable to register device: %d\n", ret); kfree(d); } } -- GitLab From 8bfcb3960fde049b863266dab8c3617bb5a541aa Mon Sep 17 00:00:00 2001 From: Thomas Petazzoni Date: Mon, 18 Aug 2008 12:33:20 +0200 Subject: [PATCH 548/750] x86: make movsl_mask definition non-CPU specific movsl_mask is currently defined in arch/x86/kernel/cpu/intel.c, which contains code specific to Intel CPUs. However, movsl_mask is used in the non-CPU specific code in arch/x86/lib/usercopy_32.c, which breaks the compilation when support for Intel CPUs is compiled out. This patch solves this problem by moving movsl_mask's definition close to its users in arch/x86/lib/usercopy_32.c. Signed-off-by: Thomas Petazzoni Cc: michael@free-electrons.com Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/intel.c | 7 ------- arch/x86/lib/usercopy_32.c | 7 +++++++ 2 files changed, 7 insertions(+), 7 deletions(-) diff --git a/arch/x86/kernel/cpu/intel.c b/arch/x86/kernel/cpu/intel.c index b75f2569b8f..5c8959b8a42 100644 --- a/arch/x86/kernel/cpu/intel.c +++ b/arch/x86/kernel/cpu/intel.c @@ -23,13 +23,6 @@ #include #endif -#ifdef CONFIG_X86_INTEL_USERCOPY -/* - * Alignment at which movsl is preferred for bulk memory copies. - */ -struct movsl_mask movsl_mask __read_mostly; -#endif - static void __cpuinit early_init_intel(struct cpuinfo_x86 *c) { /* Netburst reports 64 bytes clflush size, but does IO in 128 bytes */ diff --git a/arch/x86/lib/usercopy_32.c b/arch/x86/lib/usercopy_32.c index 24e60944971..9e68075544f 100644 --- a/arch/x86/lib/usercopy_32.c +++ b/arch/x86/lib/usercopy_32.c @@ -14,6 +14,13 @@ #include #include +#ifdef CONFIG_X86_INTEL_USERCOPY +/* + * Alignment at which movsl is preferred for bulk memory copies. + */ +struct movsl_mask movsl_mask __read_mostly; +#endif + static inline int __movsl_is_ok(unsigned long a1, unsigned long a2, unsigned long n) { #ifdef CONFIG_X86_INTEL_USERCOPY -- GitLab From 774400a3ba23b63f4de39e67ce6c4e48935809dc Mon Sep 17 00:00:00 2001 From: Thomas Petazzoni Date: Mon, 18 Aug 2008 12:33:21 +0200 Subject: [PATCH 549/750] x86: move cmpxchg fallbacks to a generic place arch/x86/kernel/cpu/intel.c defines a few fallback functions (cmpxchg_*()) that are used when the CPU doesn't support cmpxchg and/or cmpxchg64 natively. However, while defined in an Intel-specific file, these functions are also used for CPUs from other vendors when they don't support cmpxchg and/or cmpxchg64. This breaks the compilation when support for Intel CPUs is disabled. This patch moves these functions to a new arch/x86/kernel/cpu/cmpxchg.c file, unconditionally compiled when X86_32 is enabled. Signed-off-by: Thomas Petazzoni Cc: michael@free-electrons.com Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/Makefile | 2 +- arch/x86/kernel/cpu/cmpxchg.c | 72 +++++++++++++++++++++++++++++++++++ arch/x86/kernel/cpu/intel.c | 64 ------------------------------- 3 files changed, 73 insertions(+), 65 deletions(-) create mode 100644 arch/x86/kernel/cpu/cmpxchg.c diff --git a/arch/x86/kernel/cpu/Makefile b/arch/x86/kernel/cpu/Makefile index ee76eaad300..25b4c063fbf 100644 --- a/arch/x86/kernel/cpu/Makefile +++ b/arch/x86/kernel/cpu/Makefile @@ -5,7 +5,7 @@ obj-y := intel_cacheinfo.o addon_cpuid_features.o obj-y += proc.o feature_names.o -obj-$(CONFIG_X86_32) += common.o bugs.o +obj-$(CONFIG_X86_32) += common.o bugs.o cmpxchg.o obj-$(CONFIG_X86_64) += common_64.o bugs_64.o obj-$(CONFIG_X86_32) += amd.o obj-$(CONFIG_X86_64) += amd_64.o diff --git a/arch/x86/kernel/cpu/cmpxchg.c b/arch/x86/kernel/cpu/cmpxchg.c new file mode 100644 index 00000000000..2056ccf572c --- /dev/null +++ b/arch/x86/kernel/cpu/cmpxchg.c @@ -0,0 +1,72 @@ +/* + * cmpxchg*() fallbacks for CPU not supporting these instructions + */ + +#include +#include +#include + +#ifndef CONFIG_X86_CMPXCHG +unsigned long cmpxchg_386_u8(volatile void *ptr, u8 old, u8 new) +{ + u8 prev; + unsigned long flags; + + /* Poor man's cmpxchg for 386. Unsuitable for SMP */ + local_irq_save(flags); + prev = *(u8 *)ptr; + if (prev == old) + *(u8 *)ptr = new; + local_irq_restore(flags); + return prev; +} +EXPORT_SYMBOL(cmpxchg_386_u8); + +unsigned long cmpxchg_386_u16(volatile void *ptr, u16 old, u16 new) +{ + u16 prev; + unsigned long flags; + + /* Poor man's cmpxchg for 386. Unsuitable for SMP */ + local_irq_save(flags); + prev = *(u16 *)ptr; + if (prev == old) + *(u16 *)ptr = new; + local_irq_restore(flags); + return prev; +} +EXPORT_SYMBOL(cmpxchg_386_u16); + +unsigned long cmpxchg_386_u32(volatile void *ptr, u32 old, u32 new) +{ + u32 prev; + unsigned long flags; + + /* Poor man's cmpxchg for 386. Unsuitable for SMP */ + local_irq_save(flags); + prev = *(u32 *)ptr; + if (prev == old) + *(u32 *)ptr = new; + local_irq_restore(flags); + return prev; +} +EXPORT_SYMBOL(cmpxchg_386_u32); +#endif + +#ifndef CONFIG_X86_CMPXCHG64 +unsigned long long cmpxchg_486_u64(volatile void *ptr, u64 old, u64 new) +{ + u64 prev; + unsigned long flags; + + /* Poor man's cmpxchg8b for 386 and 486. Unsuitable for SMP */ + local_irq_save(flags); + prev = *(u64 *)ptr; + if (prev == old) + *(u64 *)ptr = new; + local_irq_restore(flags); + return prev; +} +EXPORT_SYMBOL(cmpxchg_486_u64); +#endif + diff --git a/arch/x86/kernel/cpu/intel.c b/arch/x86/kernel/cpu/intel.c index 5c8959b8a42..77618c717d7 100644 --- a/arch/x86/kernel/cpu/intel.c +++ b/arch/x86/kernel/cpu/intel.c @@ -307,69 +307,5 @@ static struct cpu_dev intel_cpu_dev __cpuinitdata = { cpu_vendor_dev_register(X86_VENDOR_INTEL, &intel_cpu_dev); -#ifndef CONFIG_X86_CMPXCHG -unsigned long cmpxchg_386_u8(volatile void *ptr, u8 old, u8 new) -{ - u8 prev; - unsigned long flags; - - /* Poor man's cmpxchg for 386. Unsuitable for SMP */ - local_irq_save(flags); - prev = *(u8 *)ptr; - if (prev == old) - *(u8 *)ptr = new; - local_irq_restore(flags); - return prev; -} -EXPORT_SYMBOL(cmpxchg_386_u8); - -unsigned long cmpxchg_386_u16(volatile void *ptr, u16 old, u16 new) -{ - u16 prev; - unsigned long flags; - - /* Poor man's cmpxchg for 386. Unsuitable for SMP */ - local_irq_save(flags); - prev = *(u16 *)ptr; - if (prev == old) - *(u16 *)ptr = new; - local_irq_restore(flags); - return prev; -} -EXPORT_SYMBOL(cmpxchg_386_u16); - -unsigned long cmpxchg_386_u32(volatile void *ptr, u32 old, u32 new) -{ - u32 prev; - unsigned long flags; - - /* Poor man's cmpxchg for 386. Unsuitable for SMP */ - local_irq_save(flags); - prev = *(u32 *)ptr; - if (prev == old) - *(u32 *)ptr = new; - local_irq_restore(flags); - return prev; -} -EXPORT_SYMBOL(cmpxchg_386_u32); -#endif - -#ifndef CONFIG_X86_CMPXCHG64 -unsigned long long cmpxchg_486_u64(volatile void *ptr, u64 old, u64 new) -{ - u64 prev; - unsigned long flags; - - /* Poor man's cmpxchg8b for 386 and 486. Unsuitable for SMP */ - local_irq_save(flags); - prev = *(u64 *)ptr; - if (prev == old) - *(u64 *)ptr = new; - local_irq_restore(flags); - return prev; -} -EXPORT_SYMBOL(cmpxchg_486_u64); -#endif - /* arch_initcall(intel_cpu_init); */ -- GitLab From 8d02c2110b3fb8e2700b31596a582a2989fd72ba Mon Sep 17 00:00:00 2001 From: Thomas Petazzoni Date: Tue, 5 Aug 2008 11:45:19 +0200 Subject: [PATCH 550/750] x86: configuration options to compile out x86 CPU support code This patch adds some configuration options that allow to compile out CPU vendor-specific code in x86 kernels (in arch/x86/kernel/cpu). The new configuration options are only visible when CONFIG_EMBEDDED is selected, as they are mostly interesting for space savings reasons. An example of size saving, on x86 with only Intel CPU support: text data bss dec hex filename 1125479 118760 212992 1457231 163c4f vmlinux.old 1121355 116536 212992 1450883 162383 vmlinux -4124 -2224 0 -6348 -18CC +/- However, I'm not exactly sure that the Kconfig wording is correct with regard to !64BIT / 64BIT. [ mingo@elte.hu: convert macro to inline ] Signed-off-by: Thomas Petazzoni Signed-off-by: Ingo Molnar --- arch/x86/Kconfig.cpu | 70 ++++++++++++++++++++++++++++++++++++ arch/x86/kernel/cpu/Makefile | 19 +++++----- include/asm-x86/bugs.h | 5 +++ 3 files changed, 85 insertions(+), 9 deletions(-) diff --git a/arch/x86/Kconfig.cpu b/arch/x86/Kconfig.cpu index 2c518fbc52e..6156ac25ff8 100644 --- a/arch/x86/Kconfig.cpu +++ b/arch/x86/Kconfig.cpu @@ -415,3 +415,73 @@ config X86_MINIMUM_CPU_FAMILY config X86_DEBUGCTLMSR def_bool y depends on !(MK6 || MWINCHIPC6 || MWINCHIP2 || MWINCHIP3D || MCYRIXIII || M586MMX || M586TSC || M586 || M486 || M386) + +menuconfig PROCESSOR_SELECT + default y + bool "Supported processor vendors" if EMBEDDED + help + This lets you choose what x86 vendor support code your kernel + will include. + +config CPU_SUP_INTEL_32 + default y + bool "Support Intel processors" if PROCESSOR_SELECT + depends on !64BIT + help + This enables extended support for Intel processors + +config CPU_SUP_INTEL_64 + default y + bool "Support Intel processors" if PROCESSOR_SELECT + depends on 64BIT + help + This enables extended support for Intel processors + +config CPU_SUP_CYRIX_32 + default y + bool "Support Cyrix processors" if PROCESSOR_SELECT + depends on !64BIT + help + This enables extended support for Cyrix processors + +config CPU_SUP_AMD_32 + default y + bool "Support AMD processors" if PROCESSOR_SELECT + depends on !64BIT + help + This enables extended support for AMD processors + +config CPU_SUP_AMD_64 + default y + bool "Support AMD processors" if PROCESSOR_SELECT + depends on 64BIT + help + This enables extended support for AMD processors + +config CPU_SUP_CENTAUR_32 + default y + bool "Support Centaur processors" if PROCESSOR_SELECT + depends on !64BIT + help + This enables extended support for Centaur processors + +config CPU_SUP_CENTAUR_64 + default y + bool "Support Centaur processors" if PROCESSOR_SELECT + depends on 64BIT + help + This enables extended support for Centaur processors + +config CPU_SUP_TRANSMETA_32 + default y + bool "Support Transmeta processors" if PROCESSOR_SELECT + depends on !64BIT + help + This enables extended support for Transmeta processors + +config CPU_SUP_UMC_32 + default y + bool "Support UMC processors" if PROCESSOR_SELECT + depends on !64BIT + help + This enables extended support for UMC processors diff --git a/arch/x86/kernel/cpu/Makefile b/arch/x86/kernel/cpu/Makefile index 25b4c063fbf..a0fc6c14438 100644 --- a/arch/x86/kernel/cpu/Makefile +++ b/arch/x86/kernel/cpu/Makefile @@ -7,15 +7,16 @@ obj-y += proc.o feature_names.o obj-$(CONFIG_X86_32) += common.o bugs.o cmpxchg.o obj-$(CONFIG_X86_64) += common_64.o bugs_64.o -obj-$(CONFIG_X86_32) += amd.o -obj-$(CONFIG_X86_64) += amd_64.o -obj-$(CONFIG_X86_32) += cyrix.o -obj-$(CONFIG_X86_32) += centaur.o -obj-$(CONFIG_X86_64) += centaur_64.o -obj-$(CONFIG_X86_32) += transmeta.o -obj-$(CONFIG_X86_32) += intel.o -obj-$(CONFIG_X86_64) += intel_64.o -obj-$(CONFIG_X86_32) += umc.o + +obj-$(CONFIG_CPU_SUP_AMD_32) += amd.o +obj-$(CONFIG_CPU_SUP_AMD_64) += amd_64.o +obj-$(CONFIG_CPU_SUP_CYRIX_32) += cyrix.o +obj-$(CONFIG_CPU_SUP_CENTAUR_32) += centaur.o +obj-$(CONFIG_CPU_SUP_CENTAUR_64) += centaur_64.o +obj-$(CONFIG_CPU_SUP_TRANSMETA_32) += transmeta.o +obj-$(CONFIG_CPU_SUP_INTEL_32) += intel.o +obj-$(CONFIG_CPU_SUP_INTEL_64) += intel_64.o +obj-$(CONFIG_CPU_SUP_UMC_32) += umc.o obj-$(CONFIG_X86_MCE) += mcheck/ obj-$(CONFIG_MTRR) += mtrr/ diff --git a/include/asm-x86/bugs.h b/include/asm-x86/bugs.h index 021cbdd5f25..00e4a0cd6f2 100644 --- a/include/asm-x86/bugs.h +++ b/include/asm-x86/bugs.h @@ -2,6 +2,11 @@ #define _ASM_X86_BUGS_H extern void check_bugs(void); + +#ifdef CONFIG_CPU_SUP_INTEL_32 int ppro_with_ram_bug(void); +#else +static inline int ppro_with_ram_bug(void) { return 0; } +#endif #endif /* _ASM_X86_BUGS_H */ -- GitLab From 26135ed3229a06dc8b5b7686dd272a28f5bf40b3 Mon Sep 17 00:00:00 2001 From: Martin Michlmayr Date: Fri, 15 Aug 2008 15:06:21 -0400 Subject: [PATCH 551/750] Input: cobalt_btns - add missing MODULE_LICENSE Export the module license and other information about the Cobalt button module in order to avoid the following warning: | WARNING: modpost: missing MODULE_LICENSE() in drivers/input/misc/cobalt_btns.o Signed-off-by: Martin Michlmayr Acked-by: Yoichi Yuasa Signed-off-by: Dmitry Torokhov --- drivers/input/misc/cobalt_btns.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/input/misc/cobalt_btns.c b/drivers/input/misc/cobalt_btns.c index 6a1f48b76e3..2adf9cb265d 100644 --- a/drivers/input/misc/cobalt_btns.c +++ b/drivers/input/misc/cobalt_btns.c @@ -148,6 +148,9 @@ static int __devexit cobalt_buttons_remove(struct platform_device *pdev) return 0; } +MODULE_AUTHOR("Yoichi Yuasa "); +MODULE_DESCRIPTION("Cobalt button interface driver"); +MODULE_LICENSE("GPL"); /* work with hotplug and coldplug */ MODULE_ALIAS("platform:Cobalt buttons"); -- GitLab From 0cc1fe2238e458ebe2d52f035ccc6f3d2ecc9ca1 Mon Sep 17 00:00:00 2001 From: Huang Weiyi Date: Mon, 18 Aug 2008 10:57:10 -0400 Subject: [PATCH 552/750] Input: remove version.h from drivers that don't need it If a driver dies not use LINUX_VERSION_CODE nor KERNEL_VERSION then it does not need to include version.h Signed-off-by: Huang Weiyi Acked-by: Mark Brown Signed-off-by: Dmitry Torokhov --- drivers/input/keyboard/gpio_keys.c | 1 - drivers/input/mouse/gpio_mouse.c | 1 - drivers/input/tablet/gtco.c | 1 - drivers/input/touchscreen/wm9705.c | 1 - drivers/input/touchscreen/wm9712.c | 1 - drivers/input/touchscreen/wm9713.c | 1 - drivers/input/touchscreen/wm97xx-core.c | 1 - 7 files changed, 7 deletions(-) diff --git a/drivers/input/keyboard/gpio_keys.c b/drivers/input/keyboard/gpio_keys.c index 3f48279f219..ec96b369dd7 100644 --- a/drivers/input/keyboard/gpio_keys.c +++ b/drivers/input/keyboard/gpio_keys.c @@ -9,7 +9,6 @@ */ #include -#include #include #include diff --git a/drivers/input/mouse/gpio_mouse.c b/drivers/input/mouse/gpio_mouse.c index 33929018487..72cf5e33790 100644 --- a/drivers/input/mouse/gpio_mouse.c +++ b/drivers/input/mouse/gpio_mouse.c @@ -9,7 +9,6 @@ */ #include -#include #include #include #include diff --git a/drivers/input/tablet/gtco.c b/drivers/input/tablet/gtco.c index b9b7a98bc5a..7df0228e836 100644 --- a/drivers/input/tablet/gtco.c +++ b/drivers/input/tablet/gtco.c @@ -64,7 +64,6 @@ Scott Hill shill@gtcocalcomp.com #include -#include #include /* Version with a Major number of 2 is for kernel inclusion only. */ diff --git a/drivers/input/touchscreen/wm9705.c b/drivers/input/touchscreen/wm9705.c index 978e1a13ffc..372efbc694f 100644 --- a/drivers/input/touchscreen/wm9705.c +++ b/drivers/input/touchscreen/wm9705.c @@ -17,7 +17,6 @@ #include #include -#include #include #include #include diff --git a/drivers/input/touchscreen/wm9712.c b/drivers/input/touchscreen/wm9712.c index 4c5d85a249a..c8bb1e7335f 100644 --- a/drivers/input/touchscreen/wm9712.c +++ b/drivers/input/touchscreen/wm9712.c @@ -17,7 +17,6 @@ #include #include -#include #include #include #include diff --git a/drivers/input/touchscreen/wm9713.c b/drivers/input/touchscreen/wm9713.c index 838458792ea..781ee83547e 100644 --- a/drivers/input/touchscreen/wm9713.c +++ b/drivers/input/touchscreen/wm9713.c @@ -17,7 +17,6 @@ #include #include -#include #include #include #include diff --git a/drivers/input/touchscreen/wm97xx-core.c b/drivers/input/touchscreen/wm97xx-core.c index cdc24ad314e..d589ab0e3ad 100644 --- a/drivers/input/touchscreen/wm97xx-core.c +++ b/drivers/input/touchscreen/wm97xx-core.c @@ -37,7 +37,6 @@ #include #include -#include #include #include #include -- GitLab From 88b9e2bef3e38c053ec8f054f2cbb9345724cdb1 Mon Sep 17 00:00:00 2001 From: Adrian Bunk Date: Tue, 5 Aug 2008 22:06:51 +0300 Subject: [PATCH 553/750] ath9k: work around gcc ICEs (again) (I missed the fact that the original post said to apply this patch twice... -- JWL) Original commit log message: This patch works around an internal compiler error (gcc bug #37014) in all gcc 4.2 compilers and the gcc 4.3 series up to at least 4.3.1 on at least powerpc and mips. Many thanks to Andrew Pinski for analyzing the gcc bug. Signed-off-by: Adrian Bunk Signed-off-by: John W. Linville --- drivers/net/wireless/ath9k/hw.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/drivers/net/wireless/ath9k/hw.c b/drivers/net/wireless/ath9k/hw.c index bde162f128a..a17eb130f57 100644 --- a/drivers/net/wireless/ath9k/hw.c +++ b/drivers/net/wireless/ath9k/hw.c @@ -5017,7 +5017,11 @@ static void ath9k_hw_spur_mitigate(struct ath_hal *ah, for (i = 0; i < 123; i++) { if ((cur_vit_mask > lower) && (cur_vit_mask < upper)) { - if ((abs(cur_vit_mask - bin)) < 75) + + /* workaround for gcc bug #37014 */ + volatile int tmp = abs(cur_vit_mask - bin); + + if (tmp < 75) mask_amt = 1; else mask_amt = 0; -- GitLab From aaa1553512b9105699113ea7e2ea726f3d9d4de2 Mon Sep 17 00:00:00 2001 From: Christian Lamparter Date: Sat, 9 Aug 2008 19:20:47 -0500 Subject: [PATCH 554/750] p54: Fix regression due to "net: Delete NETDEVICES_MULTIQUEUE kconfig option" Commit b19fa1f, entitled "net: Delete NETDEVICES_MULTIQUEUE kconfig option" breaks p54pci and p54usb. Additionally, the old logic always tx'ed cts frames (if enabled) with a short preamble when [rate > 3]. (i.e. with any 802.11g rate). Of course this isn't that bad, but it's still wrong! (This patch also clarifies the meanings of some of the fields in the tx header for the hardware. -- JWL) Signed-off-by: Christian Lamparter Acked-by: Larry Finger Cc: [2.6.25.x, 2.6.26.x] Signed-off-by: John W. Linville --- drivers/net/wireless/p54/p54common.c | 31 ++++++++++++++-------------- drivers/net/wireless/p54/p54common.h | 18 ++++++++-------- 2 files changed, 25 insertions(+), 24 deletions(-) diff --git a/drivers/net/wireless/p54/p54common.c b/drivers/net/wireless/p54/p54common.c index 83cd85e1f84..49afd20d2c3 100644 --- a/drivers/net/wireless/p54/p54common.c +++ b/drivers/net/wireless/p54/p54common.c @@ -413,12 +413,12 @@ static void p54_rx_frame_sent(struct ieee80211_hw *dev, struct sk_buff *skb) last_addr = range->end_addr; __skb_unlink(entry, &priv->tx_queue); memset(&info->status, 0, sizeof(info->status)); - priv->tx_stats[skb_get_queue_mapping(skb)].len--; entry_hdr = (struct p54_control_hdr *) entry->data; entry_data = (struct p54_tx_control_allocdata *) entry_hdr->data; if ((entry_hdr->magic1 & cpu_to_le16(0x4000)) != 0) pad = entry_data->align[0]; + priv->tx_stats[entry_data->hw_queue - 4].len--; if (!(info->flags & IEEE80211_TX_CTL_NO_ACK)) { if (!(payload->status & 0x01)) info->flags |= IEEE80211_TX_STAT_ACK; @@ -557,6 +557,7 @@ static int p54_tx(struct ieee80211_hw *dev, struct sk_buff *skb) struct p54_tx_control_allocdata *txhdr; size_t padding, len; u8 rate; + u8 cts_rate = 0x20; current_queue = &priv->tx_stats[skb_get_queue_mapping(skb)]; if (unlikely(current_queue->len > current_queue->limit)) @@ -581,28 +582,28 @@ static int p54_tx(struct ieee80211_hw *dev, struct sk_buff *skb) hdr->type = (info->flags & IEEE80211_TX_CTL_NO_ACK) ? 0 : cpu_to_le16(1); hdr->retry1 = hdr->retry2 = info->control.retry_limit; - memset(txhdr->wep_key, 0x0, 16); - txhdr->padding = 0; - txhdr->padding2 = 0; - /* TODO: add support for alternate retry TX rates */ rate = ieee80211_get_tx_rate(dev, info)->hw_value; - if (info->flags & IEEE80211_TX_CTL_SHORT_PREAMBLE) + if (info->flags & IEEE80211_TX_CTL_SHORT_PREAMBLE) { rate |= 0x10; - if (info->flags & IEEE80211_TX_CTL_USE_RTS_CTS) + cts_rate |= 0x10; + } + if (info->flags & IEEE80211_TX_CTL_USE_RTS_CTS) { rate |= 0x40; - else if (info->flags & IEEE80211_TX_CTL_USE_CTS_PROTECT) + cts_rate |= ieee80211_get_rts_cts_rate(dev, info)->hw_value; + } else if (info->flags & IEEE80211_TX_CTL_USE_CTS_PROTECT) { rate |= 0x20; + cts_rate |= ieee80211_get_rts_cts_rate(dev, info)->hw_value; + } memset(txhdr->rateset, rate, 8); - txhdr->wep_key_present = 0; - txhdr->wep_key_len = 0; - txhdr->frame_type = cpu_to_le32(skb_get_queue_mapping(skb) + 4); - txhdr->magic4 = 0; - txhdr->antenna = (info->antenna_sel_tx == 0) ? + txhdr->key_type = 0; + txhdr->key_len = 0; + txhdr->hw_queue = skb_get_queue_mapping(skb) + 4; + txhdr->tx_antenna = (info->antenna_sel_tx == 0) ? 2 : info->antenna_sel_tx - 1; txhdr->output_power = 0x7f; // HW Maximum - txhdr->magic5 = (info->flags & IEEE80211_TX_CTL_NO_ACK) ? - 0 : ((rate > 0x3) ? cpu_to_le32(0x33) : cpu_to_le32(0x23)); + txhdr->cts_rate = (info->flags & IEEE80211_TX_CTL_NO_ACK) ? + 0 : cts_rate; if (padding) txhdr->align[0] = padding; diff --git a/drivers/net/wireless/p54/p54common.h b/drivers/net/wireless/p54/p54common.h index 2245fcce92d..8db6c0e8e54 100644 --- a/drivers/net/wireless/p54/p54common.h +++ b/drivers/net/wireless/p54/p54common.h @@ -183,16 +183,16 @@ struct p54_frame_sent_hdr { struct p54_tx_control_allocdata { u8 rateset[8]; - u16 padding; - u8 wep_key_present; - u8 wep_key_len; - u8 wep_key[16]; - __le32 frame_type; - u32 padding2; - __le16 magic4; - u8 antenna; + u8 unalloc0[2]; + u8 key_type; + u8 key_len; + u8 key[16]; + u8 hw_queue; + u8 unalloc1[9]; + u8 tx_antenna; u8 output_power; - __le32 magic5; + u8 cts_rate; + u8 unalloc2[3]; u8 align[0]; } __attribute__ ((packed)); -- GitLab From e10e0dfe3ba358cfb442cc3bf0d3f2068785bf5c Mon Sep 17 00:00:00 2001 From: Henrique de Moraes Holschuh Date: Sat, 2 Aug 2008 14:56:25 -0300 Subject: [PATCH 555/750] rfkill: protect suspended rfkill controllers Guard rfkill controllers attached to a rfkill class against state changes after class suspend has been issued. Signed-off-by: Henrique de Moraes Holschuh Acked-by: Ivo van Doorn Signed-off-by: John W. Linville --- Documentation/rfkill.txt | 5 +++++ net/rfkill/rfkill.c | 14 ++++++++++---- 2 files changed, 15 insertions(+), 4 deletions(-) diff --git a/Documentation/rfkill.txt b/Documentation/rfkill.txt index 28b6ec87c64..6fcb3060dec 100644 --- a/Documentation/rfkill.txt +++ b/Documentation/rfkill.txt @@ -363,6 +363,11 @@ This rule exists because users of the rfkill subsystem expect to get (and set, when possible) the overall transmitter rfkill state, not of a particular rfkill line. +5. During suspend, the rfkill class will attempt to soft-block the radio +through a call to rfkill->toggle_radio, and will try to restore its previous +state during resume. After a rfkill class is suspended, it will *not* call +rfkill->toggle_radio until it is resumed. + Example of a WLAN wireless driver connected to the rfkill subsystem: -------------------------------------------------------------------- diff --git a/net/rfkill/rfkill.c b/net/rfkill/rfkill.c index d2d45655cd1..35a9994e233 100644 --- a/net/rfkill/rfkill.c +++ b/net/rfkill/rfkill.c @@ -150,6 +150,8 @@ static void update_rfkill_state(struct rfkill *rfkill) * calls and handling all the red tape such as issuing notifications * if the call is successful. * + * Suspended devices are not touched at all, and -EAGAIN is returned. + * * Note that the @force parameter cannot override a (possibly cached) * state of RFKILL_STATE_HARD_BLOCKED. Any device making use of * RFKILL_STATE_HARD_BLOCKED implements either get_state() or @@ -168,6 +170,9 @@ static int rfkill_toggle_radio(struct rfkill *rfkill, int retval = 0; enum rfkill_state oldstate, newstate; + if (unlikely(rfkill->dev.power.power_state.event & PM_EVENT_SLEEP)) + return -EBUSY; + oldstate = rfkill->state; if (rfkill->get_state && !force && @@ -214,7 +219,7 @@ static int rfkill_toggle_radio(struct rfkill *rfkill, * * This function toggles the state of all switches of given type, * unless a specific switch is claimed by userspace (in which case, - * that switch is left alone). + * that switch is left alone) or suspended. */ void rfkill_switch_all(enum rfkill_type type, enum rfkill_state state) { @@ -239,8 +244,8 @@ EXPORT_SYMBOL(rfkill_switch_all); /** * rfkill_epo - emergency power off all transmitters * - * This kicks all rfkill devices to RFKILL_STATE_SOFT_BLOCKED, ignoring - * everything in its path but rfkill_mutex and rfkill->mutex. + * This kicks all non-suspended rfkill devices to RFKILL_STATE_SOFT_BLOCKED, + * ignoring everything in its path but rfkill_mutex and rfkill->mutex. */ void rfkill_epo(void) { @@ -458,13 +463,14 @@ static int rfkill_resume(struct device *dev) if (dev->power.power_state.event != PM_EVENT_ON) { mutex_lock(&rfkill->mutex); + dev->power.power_state.event = PM_EVENT_ON; + /* restore radio state AND notify everybody */ rfkill_toggle_radio(rfkill, rfkill->state, 1); mutex_unlock(&rfkill->mutex); } - dev->power.power_state = PMSG_ON; return 0; } #else -- GitLab From 7f37441c21d3ae9fec47ef418ccafb2823d12a27 Mon Sep 17 00:00:00 2001 From: Holger Schurig Date: Thu, 7 Aug 2008 18:24:12 +0200 Subject: [PATCH 556/750] ssb: allow compilation on systems without PCI Makes ssb work on system without a PCI bus. Signed-off-by: Holger Schurig Signed-off-by: Michael Buesch Signed-off-by: John W. Linville --- drivers/ssb/main.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/drivers/ssb/main.c b/drivers/ssb/main.c index d831a2beff3..87ab2443e66 100644 --- a/drivers/ssb/main.c +++ b/drivers/ssb/main.c @@ -1165,15 +1165,19 @@ EXPORT_SYMBOL(ssb_dma_translation); int ssb_dma_set_mask(struct ssb_device *dev, u64 mask) { +#ifdef CONFIG_SSB_PCIHOST int err; +#endif switch (dev->bus->bustype) { case SSB_BUSTYPE_PCI: +#ifdef CONFIG_SSB_PCIHOST err = pci_set_dma_mask(dev->bus->host_pci, mask); if (err) return err; err = pci_set_consistent_dma_mask(dev->bus->host_pci, mask); return err; +#endif case SSB_BUSTYPE_SSB: return dma_set_mask(dev->dev, mask); default: @@ -1188,6 +1192,7 @@ void * ssb_dma_alloc_consistent(struct ssb_device *dev, size_t size, { switch (dev->bus->bustype) { case SSB_BUSTYPE_PCI: +#ifdef CONFIG_SSB_PCIHOST if (gfp_flags & GFP_DMA) { /* Workaround: The PCI API does not support passing * a GFP flag. */ @@ -1195,6 +1200,7 @@ void * ssb_dma_alloc_consistent(struct ssb_device *dev, size_t size, size, dma_handle, gfp_flags); } return pci_alloc_consistent(dev->bus->host_pci, size, dma_handle); +#endif case SSB_BUSTYPE_SSB: return dma_alloc_coherent(dev->dev, size, dma_handle, gfp_flags); default: @@ -1210,6 +1216,7 @@ void ssb_dma_free_consistent(struct ssb_device *dev, size_t size, { switch (dev->bus->bustype) { case SSB_BUSTYPE_PCI: +#ifdef CONFIG_SSB_PCIHOST if (gfp_flags & GFP_DMA) { /* Workaround: The PCI API does not support passing * a GFP flag. */ @@ -1220,6 +1227,7 @@ void ssb_dma_free_consistent(struct ssb_device *dev, size_t size, pci_free_consistent(dev->bus->host_pci, size, vaddr, dma_handle); return; +#endif case SSB_BUSTYPE_SSB: dma_free_coherent(dev->dev, size, vaddr, dma_handle); return; -- GitLab From 37465c8a3ec7279e3314623d1e2d2a50c10cf79f Mon Sep 17 00:00:00 2001 From: Michael Karcher Date: Thu, 7 Aug 2008 19:34:01 +0200 Subject: [PATCH 557/750] ath5k: Don't fiddle with MSI on suspend/resume. Commit 256b152b005e319f985f50f2a910a75ba0def74f (ath5k: don't enable MSI, we cannot handle it yet) has removed msi support, but overlooked the suspend/resume code. This patch completes msi removal. I don't consider this patch copyrightable, and thus put it into the public domain. The result is of course a base.c file dual-licensed under 3-clause-BSD and GPL. Signed-off-by: Michael Karcher Acked-by: Nick Kossifidis Signed-off-by: John W. Linville --- drivers/net/wireless/ath5k/base.c | 8 ++------ 1 file changed, 2 insertions(+), 6 deletions(-) diff --git a/drivers/net/wireless/ath5k/base.c b/drivers/net/wireless/ath5k/base.c index 2028866f599..f19f33c4e33 100644 --- a/drivers/net/wireless/ath5k/base.c +++ b/drivers/net/wireless/ath5k/base.c @@ -587,7 +587,6 @@ ath5k_pci_suspend(struct pci_dev *pdev, pm_message_t state) ath5k_stop_hw(sc); free_irq(pdev->irq, sc); - pci_disable_msi(pdev); pci_save_state(pdev); pci_disable_device(pdev); pci_set_power_state(pdev, PCI_D3hot); @@ -616,12 +615,10 @@ ath5k_pci_resume(struct pci_dev *pdev) */ pci_write_config_byte(pdev, 0x41, 0); - pci_enable_msi(pdev); - err = request_irq(pdev->irq, ath5k_intr, IRQF_SHARED, "ath", sc); if (err) { ATH5K_ERR(sc, "request_irq failed\n"); - goto err_msi; + goto err_no_irq; } err = ath5k_init(sc); @@ -642,8 +639,7 @@ ath5k_pci_resume(struct pci_dev *pdev) return 0; err_irq: free_irq(pdev->irq, sc); -err_msi: - pci_disable_msi(pdev); +err_no_irq: pci_disable_device(pdev); return err; } -- GitLab From a61dae1f784f0c4ced0d47721c0efc7033231522 Mon Sep 17 00:00:00 2001 From: Ron Rindjunsky Date: Sun, 10 Aug 2008 00:54:34 +0300 Subject: [PATCH 558/750] mac80211: update new sta's rx timestamp This patch fixes needless probe request caused by zero value in sta->last_rx inside ieee80211_associated flow Signed-off-by: Ron Rindjunsky Signed-off-by: Tomas Winkler Signed-off-by: John W. Linville --- net/mac80211/mlme.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/net/mac80211/mlme.c b/net/mac80211/mlme.c index e1d11c9b672..1e97fb9fb34 100644 --- a/net/mac80211/mlme.c +++ b/net/mac80211/mlme.c @@ -2103,6 +2103,8 @@ static void ieee80211_rx_mgmt_assoc_resp(struct ieee80211_sub_if_data *sdata, rcu_read_unlock(); return; } + /* update new sta with its last rx activity */ + sta->last_rx = jiffies; } /* -- GitLab From a58d452290aafae30b021c8bf185853b1aaf2092 Mon Sep 17 00:00:00 2001 From: Larry Finger Date: Sun, 10 Aug 2008 10:19:33 -0500 Subject: [PATCH 559/750] b43: Fix for SPROM coding error in Linksys WMP54G (BCM4306/3) The Linksys WMP54G (BCM4306/3) card in a PCI format has an SPROM coding error and needs the fix found for several other cards. Signed-off-by: Larry Finger Cc: Stable [2.6.25.x, 2.6.26.x] Signed-off-by: Michael Buesch Signed-off-by: John W. Linville --- drivers/net/wireless/b43/main.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/net/wireless/b43/main.c b/drivers/net/wireless/b43/main.c index 3bf3a869361..ee462b51410 100644 --- a/drivers/net/wireless/b43/main.c +++ b/drivers/net/wireless/b43/main.c @@ -4616,6 +4616,7 @@ static void b43_sprom_fixup(struct ssb_bus *bus) pdev = bus->host_pci; if (IS_PDEV(pdev, BROADCOM, 0x4318, ASUSTEK, 0x100F) || IS_PDEV(pdev, BROADCOM, 0x4320, LINKSYS, 0x0015) || + IS_PDEV(pdev, BROADCOM, 0x4320, LINKSYS, 0x0014) || IS_PDEV(pdev, BROADCOM, 0x4320, LINKSYS, 0x0013)) bus->sprom.boardflags_lo &= ~B43_BFL_BTCOEXIST; } -- GitLab From fcd7cc1496681f7241ef8b80f32bb35d72a4e78b Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?matthieu=20Barth=C3=A9lemy?= Date: Sun, 10 Aug 2008 23:34:59 -0500 Subject: [PATCH 560/750] rtl8187: Add USB ID for Netgear WG111V3 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Add the USB ID for a Netgear WG111v3. Signed-off-by: matthieu Barthélemy Signed-off-by: Larry Finger Signed-off-by: John W. Linville --- drivers/net/wireless/rtl8187_dev.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/net/wireless/rtl8187_dev.c b/drivers/net/wireless/rtl8187_dev.c index 57376fb993e..ca5deb6244e 100644 --- a/drivers/net/wireless/rtl8187_dev.c +++ b/drivers/net/wireless/rtl8187_dev.c @@ -40,6 +40,7 @@ static struct usb_device_id rtl8187_table[] __devinitdata = { /* Netgear */ {USB_DEVICE(0x0846, 0x6100), .driver_info = DEVICE_RTL8187}, {USB_DEVICE(0x0846, 0x6a00), .driver_info = DEVICE_RTL8187}, + {USB_DEVICE(0x0846, 0x4260), .driver_info = DEVICE_RTL8187B}, /* HP */ {USB_DEVICE(0x03f0, 0xca02), .driver_info = DEVICE_RTL8187}, /* Sitecom */ -- GitLab From 6f14792610905fe006c0c3c4d9e1478fb6be7cec Mon Sep 17 00:00:00 2001 From: Jiri Slaby Date: Mon, 11 Aug 2008 23:49:41 +0200 Subject: [PATCH 561/750] iwlwifi: fix printk newlines Add newlines at printk outputs to not break dmesg. Signed-off-by: Jiri Slaby Cc: Zhu Yi Cc: Reinette Chatre Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-4965.c | 2 +- drivers/net/wireless/iwlwifi/iwl-eeprom.c | 6 +++--- drivers/net/wireless/iwlwifi/iwl-sta.c | 4 ++-- drivers/net/wireless/iwlwifi/iwl-tx.c | 4 ++-- drivers/net/wireless/iwlwifi/iwl3945-base.c | 6 +++--- 5 files changed, 11 insertions(+), 11 deletions(-) diff --git a/drivers/net/wireless/iwlwifi/iwl-4965.c b/drivers/net/wireless/iwlwifi/iwl-4965.c index 22bb26985c2..4a0cc78d55e 100644 --- a/drivers/net/wireless/iwlwifi/iwl-4965.c +++ b/drivers/net/wireless/iwlwifi/iwl-4965.c @@ -967,7 +967,7 @@ static int iwl4965_interpolate_chan(struct iwl_priv *priv, u32 channel, s = iwl4965_get_sub_band(priv, channel); if (s >= EEPROM_TX_POWER_BANDS) { - IWL_ERROR("Tx Power can not find channel %d ", channel); + IWL_ERROR("Tx Power can not find channel %d\n", channel); return -1; } diff --git a/drivers/net/wireless/iwlwifi/iwl-eeprom.c b/drivers/net/wireless/iwlwifi/iwl-eeprom.c index bce53830b30..19985bf0dcc 100644 --- a/drivers/net/wireless/iwlwifi/iwl-eeprom.c +++ b/drivers/net/wireless/iwlwifi/iwl-eeprom.c @@ -146,7 +146,7 @@ int iwlcore_eeprom_verify_signature(struct iwl_priv *priv) { u32 gp = iwl_read32(priv, CSR_EEPROM_GP); if ((gp & CSR_EEPROM_GP_VALID_MSK) == CSR_EEPROM_GP_BAD_SIGNATURE) { - IWL_ERROR("EEPROM not found, EEPROM_GP=0x%08x", gp); + IWL_ERROR("EEPROM not found, EEPROM_GP=0x%08x\n", gp); return -ENOENT; } return 0; @@ -227,7 +227,7 @@ int iwl_eeprom_init(struct iwl_priv *priv) ret = priv->cfg->ops->lib->eeprom_ops.verify_signature(priv); if (ret < 0) { - IWL_ERROR("EEPROM not found, EEPROM_GP=0x%08x", gp); + IWL_ERROR("EEPROM not found, EEPROM_GP=0x%08x\n", gp); ret = -ENOENT; goto err; } @@ -254,7 +254,7 @@ int iwl_eeprom_init(struct iwl_priv *priv) } if (!(r & CSR_EEPROM_REG_READ_VALID_MSK)) { - IWL_ERROR("Time out reading EEPROM[%d]", addr); + IWL_ERROR("Time out reading EEPROM[%d]\n", addr); ret = -ETIMEDOUT; goto done; } diff --git a/drivers/net/wireless/iwlwifi/iwl-sta.c b/drivers/net/wireless/iwlwifi/iwl-sta.c index 60a6e010603..6283a3a707f 100644 --- a/drivers/net/wireless/iwlwifi/iwl-sta.c +++ b/drivers/net/wireless/iwlwifi/iwl-sta.c @@ -207,7 +207,7 @@ static void iwl_set_ht_add_station(struct iwl_priv *priv, u8 index, case WLAN_HT_CAP_MIMO_PS_DISABLED: break; default: - IWL_WARNING("Invalid MIMO PS mode %d", mimo_ps_mode); + IWL_WARNING("Invalid MIMO PS mode %d\n", mimo_ps_mode); break; } @@ -969,7 +969,7 @@ int iwl_get_sta_id(struct iwl_priv *priv, struct ieee80211_hdr *hdr) return priv->hw_params.bcast_sta_id; default: - IWL_WARNING("Unknown mode of operation: %d", priv->iw_mode); + IWL_WARNING("Unknown mode of operation: %d\n", priv->iw_mode); return priv->hw_params.bcast_sta_id; } } diff --git a/drivers/net/wireless/iwlwifi/iwl-tx.c b/drivers/net/wireless/iwlwifi/iwl-tx.c index 4108c7c8f00..d82823b5c8a 100644 --- a/drivers/net/wireless/iwlwifi/iwl-tx.c +++ b/drivers/net/wireless/iwlwifi/iwl-tx.c @@ -493,7 +493,7 @@ int iwl_txq_ctx_reset(struct iwl_priv *priv) /* Alloc keep-warm buffer */ ret = iwl_kw_alloc(priv); if (ret) { - IWL_ERROR("Keep Warm allocation failed"); + IWL_ERROR("Keep Warm allocation failed\n"); goto error_kw; } spin_lock_irqsave(&priv->lock, flags); @@ -1463,7 +1463,7 @@ void iwl_rx_reply_compressed_ba(struct iwl_priv *priv, u16 ba_resp_scd_ssn = le16_to_cpu(ba_resp->scd_ssn); if (scd_flow >= priv->hw_params.max_txq_num) { - IWL_ERROR("BUG_ON scd_flow is bigger than number of queues"); + IWL_ERROR("BUG_ON scd_flow is bigger than number of queues\n"); return; } diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c index 444847ab1b5..348048a4b6c 100644 --- a/drivers/net/wireless/iwlwifi/iwl3945-base.c +++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c @@ -1558,7 +1558,7 @@ int iwl3945_eeprom_init(struct iwl3945_priv *priv) BUILD_BUG_ON(sizeof(priv->eeprom) != IWL_EEPROM_IMAGE_SIZE); if ((gp & CSR_EEPROM_GP_VALID_MSK) == CSR_EEPROM_GP_BAD_SIGNATURE) { - IWL_ERROR("EEPROM not found, EEPROM_GP=0x%08x", gp); + IWL_ERROR("EEPROM not found, EEPROM_GP=0x%08x\n", gp); return -ENOENT; } @@ -1583,7 +1583,7 @@ int iwl3945_eeprom_init(struct iwl3945_priv *priv) } if (!(r & CSR_EEPROM_REG_READ_VALID_MSK)) { - IWL_ERROR("Time out reading EEPROM[%d]", addr); + IWL_ERROR("Time out reading EEPROM[%d]\n", addr); return -ETIMEDOUT; } e[addr / 2] = le16_to_cpu((__force __le16)(r >> 16)); @@ -2507,7 +2507,7 @@ static int iwl3945_get_sta_id(struct iwl3945_priv *priv, struct ieee80211_hdr *h return priv->hw_setting.bcast_sta_id; default: - IWL_WARNING("Unknown mode of operation: %d", priv->iw_mode); + IWL_WARNING("Unknown mode of operation: %d\n", priv->iw_mode); return priv->hw_setting.bcast_sta_id; } } -- GitLab From 69bbc7dc9f59fedb6067c7f9f9f9bc1da27407ad Mon Sep 17 00:00:00 2001 From: Christian Lamparter Date: Wed, 13 Aug 2008 23:41:45 +0200 Subject: [PATCH 562/750] p54: move p54_vdcf_init to the right place. priv->tx_hdr_len is set by the driver _after_ it called p54_init_common. While this isn't much a problem for any PCI or ISL3887 cards/sticks, because they don't need any extra header and therefore tx_hdr_len is zero for them... Signed-off-by: Christian Lamparter Signed-off-by: John W. Linville --- drivers/net/wireless/p54/p54common.c | 20 +++++++++++--------- 1 file changed, 11 insertions(+), 9 deletions(-) diff --git a/drivers/net/wireless/p54/p54common.c b/drivers/net/wireless/p54/p54common.c index 49afd20d2c3..29be3dc8ee0 100644 --- a/drivers/net/wireless/p54/p54common.c +++ b/drivers/net/wireless/p54/p54common.c @@ -837,10 +837,21 @@ static int p54_start(struct ieee80211_hw *dev) struct p54_common *priv = dev->priv; int err; + if (!priv->cached_vdcf) { + priv->cached_vdcf = kzalloc(sizeof(struct p54_tx_control_vdcf)+ + priv->tx_hdr_len + sizeof(struct p54_control_hdr), + GFP_KERNEL); + + if (!priv->cached_vdcf) + return -ENOMEM; + } + err = priv->open(dev); if (!err) priv->mode = IEEE80211_IF_TYPE_MNTR; + p54_init_vdcf(dev); + return err; } @@ -1020,15 +1031,6 @@ struct ieee80211_hw *p54_init_common(size_t priv_data_len) dev->extra_tx_headroom = sizeof(struct p54_control_hdr) + 4 + sizeof(struct p54_tx_control_allocdata); - priv->cached_vdcf = kzalloc(sizeof(struct p54_tx_control_vdcf) + - priv->tx_hdr_len + sizeof(struct p54_control_hdr), GFP_KERNEL); - - if (!priv->cached_vdcf) { - ieee80211_free_hw(dev); - return NULL; - } - - p54_init_vdcf(dev); mutex_init(&priv->conf_mutex); return dev; -- GitLab From d47c3cebf5aae9d72b2cc18e5ac3b520fdbb0bca Mon Sep 17 00:00:00 2001 From: Christian Lamparter Date: Wed, 13 Aug 2008 23:41:48 +0200 Subject: [PATCH 563/750] p54u: reset skb's data/tail pointer on requeue (Only important for USB V1 Adaptors) If an incoming frame wasn't accepted by p54_rx function the skb will be reused for new frames... But, we must not forget to set the skb's data pointers into the same state in which it was initialized by p54u_init_urbs. Otherwise we either end up with 16 bytes less on every requeue, or if a new frame is worthy enough to be accepted, the data is in the wrong place (urb->transfer_buffer wasn't updated!) and mac80211 has a hard time to recognize it... Signed-off-by: Christian Lamparter Signed-off-by: John W. Linville --- drivers/net/wireless/p54/p54usb.c | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/drivers/net/wireless/p54/p54usb.c b/drivers/net/wireless/p54/p54usb.c index 815c095ef79..cbaca23a945 100644 --- a/drivers/net/wireless/p54/p54usb.c +++ b/drivers/net/wireless/p54/p54usb.c @@ -109,7 +109,17 @@ static void p54u_rx_cb(struct urb *urb) urb->context = skb; skb_queue_tail(&priv->rx_queue, skb); } else { + if (!priv->hw_type) + skb_push(skb, sizeof(struct net2280_tx_hdr)); + + skb_reset_tail_pointer(skb); skb_trim(skb, 0); + if (urb->transfer_buffer != skb_tail_pointer(skb)) { + /* this should not happen */ + WARN_ON(1); + urb->transfer_buffer = skb_tail_pointer(skb); + } + skb_queue_tail(&priv->rx_queue, skb); } -- GitLab From 546c80c91f8d847477ee8354aad26f116048169d Mon Sep 17 00:00:00 2001 From: "Luis R. Rodriguez" Date: Thu, 14 Aug 2008 11:43:20 -0700 Subject: [PATCH 564/750] mac80211: remove kdoc references to IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE was made unnecessary in the recent revamp on beacon configuration. Signed-off-by: Luis R. Rodriguez Signed-off-by: John W. Linville --- include/net/mac80211.h | 11 +++-------- 1 file changed, 3 insertions(+), 8 deletions(-) diff --git a/include/net/mac80211.h b/include/net/mac80211.h index b397e4d984c..ff137fd7714 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -708,10 +708,7 @@ enum ieee80211_tkip_key_type { * rely on the host system for such buffering. This option is used * to configure the IEEE 802.11 upper layer to buffer broadcast and * multicast frames when there are power saving stations so that - * the driver can fetch them with ieee80211_get_buffered_bc(). Note - * that not setting this flag works properly only when the - * %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is also not set because - * otherwise the stack will not know when the DTIM beacon was sent. + * the driver can fetch them with ieee80211_get_buffered_bc(). * * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE: * Hardware is not capable of short slot operation on the 2.4 GHz band. @@ -1099,10 +1096,8 @@ enum ieee80211_ampdu_mlme_action { * See the section "Frame filtering" for more information. * This callback must be implemented and atomic. * - * @set_tim: Set TIM bit. If the hardware/firmware takes care of beacon - * generation (that is, %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is set) - * mac80211 calls this function when a TIM bit must be set or cleared - * for a given AID. Must be atomic. + * @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit + * must be set or cleared for a given AID. Must be atomic. * * @set_key: See the section "Hardware crypto acceleration" * This callback can sleep, and is only called between add_interface -- GitLab From 430cd47fa98178b5199105fab4fb74e04bd0635c Mon Sep 17 00:00:00 2001 From: Larry Finger Date: Thu, 14 Aug 2008 18:57:11 -0500 Subject: [PATCH 565/750] b43: Fix for another Bluetooth Coexistence SPROM Programming error for BCM4306 In trying to help users on the Ubuntu Bugzilla, I discovered another BCM4306 with the Bluetooth Coexistence programming error in the SPROM. This patch is contingent on the one that added the Linksys device with subdevice code of 0x0014. Signed-off-by: Larry Finger Cc: Stable Signed-off-by: John W. Linville --- drivers/net/wireless/b43/main.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/net/wireless/b43/main.c b/drivers/net/wireless/b43/main.c index ee462b51410..8e09982fded 100644 --- a/drivers/net/wireless/b43/main.c +++ b/drivers/net/wireless/b43/main.c @@ -4615,6 +4615,7 @@ static void b43_sprom_fixup(struct ssb_bus *bus) if (bus->bustype == SSB_BUSTYPE_PCI) { pdev = bus->host_pci; if (IS_PDEV(pdev, BROADCOM, 0x4318, ASUSTEK, 0x100F) || + IS_PDEV(pdev, BROADCOM, 0x4320, DELL, 0x0003) || IS_PDEV(pdev, BROADCOM, 0x4320, LINKSYS, 0x0015) || IS_PDEV(pdev, BROADCOM, 0x4320, LINKSYS, 0x0014) || IS_PDEV(pdev, BROADCOM, 0x4320, LINKSYS, 0x0013)) -- GitLab From f126cba427170eac9e37311b2ab7afc0e2261906 Mon Sep 17 00:00:00 2001 From: Jochen Friedrich Date: Fri, 15 Aug 2008 14:47:46 +0200 Subject: [PATCH 566/750] rt2x00: Fix txdone_entry_desc_flags txdone_entry_desc_flags is used with __set_bit and test_bit which bit-shift the values, so don't bit-shift the flags in the enum. Also make sure flags are initialized before being used. Signed-off-by: Jochen Friedrich Signed-off-by: Ivo van Doorn Signed-off-by: John W. Linville --- drivers/net/wireless/rt2x00/rt2x00queue.h | 8 ++++---- drivers/net/wireless/rt2x00/rt2x00usb.c | 1 + 2 files changed, 5 insertions(+), 4 deletions(-) diff --git a/drivers/net/wireless/rt2x00/rt2x00queue.h b/drivers/net/wireless/rt2x00/rt2x00queue.h index a4a8c57004d..ff78e52ce43 100644 --- a/drivers/net/wireless/rt2x00/rt2x00queue.h +++ b/drivers/net/wireless/rt2x00/rt2x00queue.h @@ -173,10 +173,10 @@ struct rxdone_entry_desc { * frame transmission failed due to excessive retries. */ enum txdone_entry_desc_flags { - TXDONE_UNKNOWN = 1 << 0, - TXDONE_SUCCESS = 1 << 1, - TXDONE_FAILURE = 1 << 2, - TXDONE_EXCESSIVE_RETRY = 1 << 3, + TXDONE_UNKNOWN, + TXDONE_SUCCESS, + TXDONE_FAILURE, + TXDONE_EXCESSIVE_RETRY, }; /** diff --git a/drivers/net/wireless/rt2x00/rt2x00usb.c b/drivers/net/wireless/rt2x00/rt2x00usb.c index 8d76bb2e031..2050227ea53 100644 --- a/drivers/net/wireless/rt2x00/rt2x00usb.c +++ b/drivers/net/wireless/rt2x00/rt2x00usb.c @@ -181,6 +181,7 @@ static void rt2x00usb_interrupt_txdone(struct urb *urb) * (Only indirectly by looking at the failed TX counters * in the register). */ + txdesc.flags = 0; if (!urb->status) __set_bit(TXDONE_UNKNOWN, &txdesc.flags); else -- GitLab From 3eb75aac8907e7ea36f0d078b2cc7393986001cf Mon Sep 17 00:00:00 2001 From: Huang Weiyi Date: Sun, 17 Aug 2008 07:50:47 +0800 Subject: [PATCH 567/750] removed unused #include The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION. drivers/net/wireless/ath5k/base.c drivers/net/wireless/b43/main.c drivers/net/wireless/ipw2100.c drivers/net/wireless/ipw2200.c drivers/net/wireless/iwlwifi/iwl-3945.c drivers/net/wireless/iwlwifi/iwl-4965.c drivers/net/wireless/iwlwifi/iwl-5000.c drivers/net/wireless/iwlwifi/iwl-agn.c drivers/net/wireless/iwlwifi/iwl-core.c drivers/net/wireless/iwlwifi/iwl-eeprom.c drivers/net/wireless/iwlwifi/iwl-hcmd.c drivers/net/wireless/iwlwifi/iwl-power.c drivers/net/wireless/iwlwifi/iwl3945-base.c This patch removes the said #include . Signed-off-by: Huang Weiyi Signed-off-by: John W. Linville --- drivers/net/wireless/ath5k/base.c | 1 - drivers/net/wireless/b43/main.c | 1 - drivers/net/wireless/ipw2100.c | 1 - drivers/net/wireless/ipw2200.c | 1 - drivers/net/wireless/iwlwifi/iwl-3945.c | 1 - drivers/net/wireless/iwlwifi/iwl-4965.c | 1 - drivers/net/wireless/iwlwifi/iwl-5000.c | 1 - drivers/net/wireless/iwlwifi/iwl-agn.c | 1 - drivers/net/wireless/iwlwifi/iwl-core.c | 1 - drivers/net/wireless/iwlwifi/iwl-eeprom.c | 1 - drivers/net/wireless/iwlwifi/iwl-hcmd.c | 1 - drivers/net/wireless/iwlwifi/iwl-power.c | 1 - drivers/net/wireless/iwlwifi/iwl3945-base.c | 1 - 13 files changed, 13 deletions(-) diff --git a/drivers/net/wireless/ath5k/base.c b/drivers/net/wireless/ath5k/base.c index f19f33c4e33..b20a45aa868 100644 --- a/drivers/net/wireless/ath5k/base.c +++ b/drivers/net/wireless/ath5k/base.c @@ -40,7 +40,6 @@ * */ -#include #include #include #include diff --git a/drivers/net/wireless/b43/main.c b/drivers/net/wireless/b43/main.c index 8e09982fded..7205a936ec7 100644 --- a/drivers/net/wireless/b43/main.c +++ b/drivers/net/wireless/b43/main.c @@ -33,7 +33,6 @@ #include #include #include -#include #include #include #include diff --git a/drivers/net/wireless/ipw2100.c b/drivers/net/wireless/ipw2100.c index c6f886ec08a..19a401c4a0d 100644 --- a/drivers/net/wireless/ipw2100.c +++ b/drivers/net/wireless/ipw2100.c @@ -157,7 +157,6 @@ that only one external action is invoked at a time. #include #include #include -#include #include #include #include diff --git a/drivers/net/wireless/ipw2200.c b/drivers/net/wireless/ipw2200.c index 36e8d2f6e7b..dcce3542d5a 100644 --- a/drivers/net/wireless/ipw2200.c +++ b/drivers/net/wireless/ipw2200.c @@ -31,7 +31,6 @@ ******************************************************************************/ #include "ipw2200.h" -#include #ifndef KBUILD_EXTMOD diff --git a/drivers/net/wireless/iwlwifi/iwl-3945.c b/drivers/net/wireless/iwlwifi/iwl-3945.c index b3931f6135a..3f51f363534 100644 --- a/drivers/net/wireless/iwlwifi/iwl-3945.c +++ b/drivers/net/wireless/iwlwifi/iwl-3945.c @@ -26,7 +26,6 @@ #include #include -#include #include #include #include diff --git a/drivers/net/wireless/iwlwifi/iwl-4965.c b/drivers/net/wireless/iwlwifi/iwl-4965.c index 4a0cc78d55e..e2581229d8b 100644 --- a/drivers/net/wireless/iwlwifi/iwl-4965.c +++ b/drivers/net/wireless/iwlwifi/iwl-4965.c @@ -26,7 +26,6 @@ #include #include -#include #include #include #include diff --git a/drivers/net/wireless/iwlwifi/iwl-5000.c b/drivers/net/wireless/iwlwifi/iwl-5000.c index f3d139b663e..cbc01a00eaf 100644 --- a/drivers/net/wireless/iwlwifi/iwl-5000.c +++ b/drivers/net/wireless/iwlwifi/iwl-5000.c @@ -25,7 +25,6 @@ #include #include -#include #include #include #include diff --git a/drivers/net/wireless/iwlwifi/iwl-agn.c b/drivers/net/wireless/iwlwifi/iwl-agn.c index ed09e48b1b6..061ffba9c88 100644 --- a/drivers/net/wireless/iwlwifi/iwl-agn.c +++ b/drivers/net/wireless/iwlwifi/iwl-agn.c @@ -29,7 +29,6 @@ #include #include -#include #include #include #include diff --git a/drivers/net/wireless/iwlwifi/iwl-core.c b/drivers/net/wireless/iwlwifi/iwl-core.c index 9bd61809129..c72f72579be 100644 --- a/drivers/net/wireless/iwlwifi/iwl-core.c +++ b/drivers/net/wireless/iwlwifi/iwl-core.c @@ -28,7 +28,6 @@ #include #include -#include #include struct iwl_priv; /* FIXME: remove */ diff --git a/drivers/net/wireless/iwlwifi/iwl-eeprom.c b/drivers/net/wireless/iwlwifi/iwl-eeprom.c index 19985bf0dcc..37155755efc 100644 --- a/drivers/net/wireless/iwlwifi/iwl-eeprom.c +++ b/drivers/net/wireless/iwlwifi/iwl-eeprom.c @@ -63,7 +63,6 @@ #include #include -#include #include #include diff --git a/drivers/net/wireless/iwlwifi/iwl-hcmd.c b/drivers/net/wireless/iwlwifi/iwl-hcmd.c index 6512834bb91..2eb03eea190 100644 --- a/drivers/net/wireless/iwlwifi/iwl-hcmd.c +++ b/drivers/net/wireless/iwlwifi/iwl-hcmd.c @@ -28,7 +28,6 @@ #include #include -#include #include #include "iwl-dev.h" /* FIXME: remove */ diff --git a/drivers/net/wireless/iwlwifi/iwl-power.c b/drivers/net/wireless/iwlwifi/iwl-power.c index 028e3053c0c..a099c9e30e5 100644 --- a/drivers/net/wireless/iwlwifi/iwl-power.c +++ b/drivers/net/wireless/iwlwifi/iwl-power.c @@ -29,7 +29,6 @@ #include #include -#include #include #include diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c index 348048a4b6c..b775d5bab66 100644 --- a/drivers/net/wireless/iwlwifi/iwl3945-base.c +++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c @@ -29,7 +29,6 @@ #include #include -#include #include #include #include -- GitLab From a69999e286b5da33232694a2ad99c29419b91a44 Mon Sep 17 00:00:00 2001 From: Adrian Bunk Date: Mon, 18 Aug 2008 21:40:03 +0200 Subject: [PATCH 568/750] drivers/ide/pci/: use __devexit_p() This patch adds missing __devexit_p's. Reported-by: Russell King Signed-off-by: Adrian Bunk Signed-off-by: Bartlomiej Zolnierkiewicz --- drivers/ide/pci/aec62xx.c | 2 +- drivers/ide/pci/cy82c693.c | 2 +- drivers/ide/pci/hpt366.c | 2 +- drivers/ide/pci/it821x.c | 2 +- drivers/ide/pci/pdc202xx_new.c | 2 +- drivers/ide/pci/scc_pata.c | 2 +- drivers/ide/pci/siimage.c | 2 +- drivers/ide/pci/sis5513.c | 2 +- drivers/ide/pci/tc86c001.c | 2 +- drivers/ide/pci/via82cxxx.c | 2 +- 10 files changed, 10 insertions(+), 10 deletions(-) diff --git a/drivers/ide/pci/aec62xx.c b/drivers/ide/pci/aec62xx.c index 40644b6f1c0..3187215e8f8 100644 --- a/drivers/ide/pci/aec62xx.c +++ b/drivers/ide/pci/aec62xx.c @@ -307,7 +307,7 @@ static struct pci_driver driver = { .name = "AEC62xx_IDE", .id_table = aec62xx_pci_tbl, .probe = aec62xx_init_one, - .remove = aec62xx_remove, + .remove = __devexit_p(aec62xx_remove), }; static int __init aec62xx_ide_init(void) diff --git a/drivers/ide/pci/cy82c693.c b/drivers/ide/pci/cy82c693.c index bfae2f882f4..e6d8ee88d56 100644 --- a/drivers/ide/pci/cy82c693.c +++ b/drivers/ide/pci/cy82c693.c @@ -447,7 +447,7 @@ static struct pci_driver driver = { .name = "Cypress_IDE", .id_table = cy82c693_pci_tbl, .probe = cy82c693_init_one, - .remove = cy82c693_remove, + .remove = __devexit_p(cy82c693_remove), }; static int __init cy82c693_ide_init(void) diff --git a/drivers/ide/pci/hpt366.c b/drivers/ide/pci/hpt366.c index 748793a413a..eb107eef0db 100644 --- a/drivers/ide/pci/hpt366.c +++ b/drivers/ide/pci/hpt366.c @@ -1620,7 +1620,7 @@ static struct pci_driver driver = { .name = "HPT366_IDE", .id_table = hpt366_pci_tbl, .probe = hpt366_init_one, - .remove = hpt366_remove, + .remove = __devexit_p(hpt366_remove), }; static int __init hpt366_ide_init(void) diff --git a/drivers/ide/pci/it821x.c b/drivers/ide/pci/it821x.c index b6dc723de70..4a1508a707c 100644 --- a/drivers/ide/pci/it821x.c +++ b/drivers/ide/pci/it821x.c @@ -686,7 +686,7 @@ static struct pci_driver driver = { .name = "ITE821x IDE", .id_table = it821x_pci_tbl, .probe = it821x_init_one, - .remove = it821x_remove, + .remove = __devexit_p(it821x_remove), }; static int __init it821x_ide_init(void) diff --git a/drivers/ide/pci/pdc202xx_new.c b/drivers/ide/pci/pdc202xx_new.c index 0f609b72f47..d477da6b585 100644 --- a/drivers/ide/pci/pdc202xx_new.c +++ b/drivers/ide/pci/pdc202xx_new.c @@ -566,7 +566,7 @@ static struct pci_driver driver = { .name = "Promise_IDE", .id_table = pdc202new_pci_tbl, .probe = pdc202new_init_one, - .remove = pdc202new_remove, + .remove = __devexit_p(pdc202new_remove), }; static int __init pdc202new_ide_init(void) diff --git a/drivers/ide/pci/scc_pata.c b/drivers/ide/pci/scc_pata.c index 6cde48bba6f..44cccd1e086 100644 --- a/drivers/ide/pci/scc_pata.c +++ b/drivers/ide/pci/scc_pata.c @@ -954,7 +954,7 @@ static struct pci_driver driver = { .name = "SCC IDE", .id_table = scc_pci_tbl, .probe = scc_init_one, - .remove = scc_remove, + .remove = __devexit_p(scc_remove), }; static int scc_ide_init(void) diff --git a/drivers/ide/pci/siimage.c b/drivers/ide/pci/siimage.c index 445ce6fbea3..db2b88a369a 100644 --- a/drivers/ide/pci/siimage.c +++ b/drivers/ide/pci/siimage.c @@ -832,7 +832,7 @@ static struct pci_driver driver = { .name = "SiI_IDE", .id_table = siimage_pci_tbl, .probe = siimage_init_one, - .remove = siimage_remove, + .remove = __devexit_p(siimage_remove), }; static int __init siimage_ide_init(void) diff --git a/drivers/ide/pci/sis5513.c b/drivers/ide/pci/sis5513.c index e5a4b42b4e3..5efe21d6ef9 100644 --- a/drivers/ide/pci/sis5513.c +++ b/drivers/ide/pci/sis5513.c @@ -610,7 +610,7 @@ static struct pci_driver driver = { .name = "SIS_IDE", .id_table = sis5513_pci_tbl, .probe = sis5513_init_one, - .remove = sis5513_remove, + .remove = __devexit_p(sis5513_remove), }; static int __init sis5513_ide_init(void) diff --git a/drivers/ide/pci/tc86c001.c b/drivers/ide/pci/tc86c001.c index 7fc88c375e5..927277c54ec 100644 --- a/drivers/ide/pci/tc86c001.c +++ b/drivers/ide/pci/tc86c001.c @@ -249,7 +249,7 @@ static struct pci_driver driver = { .name = "TC86C001", .id_table = tc86c001_pci_tbl, .probe = tc86c001_init_one, - .remove = tc86c001_remove, + .remove = __devexit_p(tc86c001_remove), }; static int __init tc86c001_ide_init(void) diff --git a/drivers/ide/pci/via82cxxx.c b/drivers/ide/pci/via82cxxx.c index a6b2cc83f29..94fb9ab3223 100644 --- a/drivers/ide/pci/via82cxxx.c +++ b/drivers/ide/pci/via82cxxx.c @@ -491,7 +491,7 @@ static struct pci_driver driver = { .name = "VIA_IDE", .id_table = via_pci_tbl, .probe = via_init_one, - .remove = via_remove, + .remove = __devexit_p(via_remove), }; static int __init via_ide_init(void) -- GitLab From 1f49060adcc1817337af95392bdf8a6205abffa0 Mon Sep 17 00:00:00 2001 From: Adrian Bunk Date: Mon, 18 Aug 2008 21:40:03 +0200 Subject: [PATCH 569/750] cleanup powerpc/include/asm/ide.h This patch removes code that became unused through IDE changes and the arch/ppc/ removal. Signed-off-by: Adrian Bunk Signed-off-by: Bartlomiej Zolnierkiewicz --- arch/powerpc/include/asm/ide.h | 43 +--------------------------------- 1 file changed, 1 insertion(+), 42 deletions(-) diff --git a/arch/powerpc/include/asm/ide.h b/arch/powerpc/include/asm/ide.h index 048480e340f..da01b20aea5 100644 --- a/arch/powerpc/include/asm/ide.h +++ b/arch/powerpc/include/asm/ide.h @@ -6,12 +6,7 @@ #ifndef _ASM_POWERPC_IDE_H #define _ASM_POWERPC_IDE_H -#ifdef __KERNEL__ - -#ifndef __powerpc64__ -#include -#include -#endif +#include #include #define __ide_mm_insw(p, a, c) readsw((void __iomem *)(p), (a), (c)) @@ -19,40 +14,4 @@ #define __ide_mm_outsw(p, a, c) writesw((void __iomem *)(p), (a), (c)) #define __ide_mm_outsl(p, a, c) writesl((void __iomem *)(p), (a), (c)) -#ifndef __powerpc64__ -#include - -/* FIXME: use ide_platform host driver */ -static __inline__ int ide_default_irq(unsigned long base) -{ -#ifdef CONFIG_PPLUS - switch (base) { - case 0x1f0: return 14; - case 0x170: return 15; - } -#endif - return 0; -} - -/* FIXME: use ide_platform host driver */ -static __inline__ unsigned long ide_default_io_base(int index) -{ -#ifdef CONFIG_PPLUS - switch (index) { - case 0: return 0x1f0; - case 1: return 0x170; - } -#endif - return 0; -} - -#ifdef CONFIG_BLK_DEV_MPC8xx_IDE -#define IDE_ARCH_ACK_INTR 1 -#define ide_ack_intr(hwif) ((hwif)->ack_intr ? (hwif)->ack_intr(hwif) : 1) -#endif - -#endif /* __powerpc64__ */ - -#endif /* __KERNEL__ */ - #endif /* _ASM_POWERPC_IDE_H */ -- GitLab From 3e636f78e5bbe95831e4d0071ee8f40b507e1cbd Mon Sep 17 00:00:00 2001 From: Borislav Petkov Date: Mon, 18 Aug 2008 21:40:03 +0200 Subject: [PATCH 570/750] viocd: add dummy audio ioctl handler Make sure audio_ioctl is always defined even if being a dummy function since the cdrom_ioctl interface assumes its existence and we don't want to BUG on null ptr on some ioctls like, e.g. CDROMREADTOCENTRY, CDROMREADTOCHDR etc. when we fix CDC_PLAY_AUDIO checking in cdrom.c. Signed-off-by: Borislav Petkov Acked-by: Stephen Rothwell Signed-off-by: Bartlomiej Zolnierkiewicz --- drivers/cdrom/viocd.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/cdrom/viocd.c b/drivers/cdrom/viocd.c index 9d0dfe6e0d6..031e0e1a1a3 100644 --- a/drivers/cdrom/viocd.c +++ b/drivers/cdrom/viocd.c @@ -550,12 +550,19 @@ return_complete: } } +static int viocd_audio_ioctl(struct cdrom_device_info *cdi, unsigned int cmd, + void *arg) +{ + return -EINVAL; +} + static struct cdrom_device_ops viocd_dops = { .open = viocd_open, .release = viocd_release, .media_changed = viocd_media_changed, .lock_door = viocd_lock_door, .generic_packet = viocd_packet, + .audio_ioctl = viocd_audio_ioctl, .capability = CDC_CLOSE_TRAY | CDC_OPEN_TRAY | CDC_LOCK | CDC_SELECT_SPEED | CDC_SELECT_DISC | CDC_MULTI_SESSION | CDC_MCN | CDC_MEDIA_CHANGED | CDC_PLAY_AUDIO | CDC_RESET | CDC_DRIVE_STATUS | CDC_GENERIC_PACKET | CDC_CD_R | CDC_CD_RW | CDC_DVD | CDC_DVD_R | CDC_DVD_RAM | CDC_RAM }; -- GitLab From d15cad5df1dac17ae33152646f599f0bdc6be48e Mon Sep 17 00:00:00 2001 From: Borislav Petkov Date: Mon, 18 Aug 2008 21:40:04 +0200 Subject: [PATCH 571/750] gdrom: add dummy audio_ioctl handler Make sure audio_ioctl is always defined even if being a dummy function since the cdrom_ioctl interface assumes its existence and we don't want to BUG on null ptr on some ioctls like, e.g. CDROMREADTOCENTRY, CDROMREADTOCHDR etc. when we fix CDC_PLAY_AUDIO checking in cdrom.c. Signed-off-by: Borislav Petkov Acked-by: Adrian McMenamin Signed-off-by: Bartlomiej Zolnierkiewicz --- drivers/cdrom/gdrom.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/cdrom/gdrom.c b/drivers/cdrom/gdrom.c index 1e0455bd6df..1231d95aa69 100644 --- a/drivers/cdrom/gdrom.c +++ b/drivers/cdrom/gdrom.c @@ -471,6 +471,12 @@ cleanup_sense_final: return err; } +static int gdrom_audio_ioctl(struct cdrom_device_info *cdi, unsigned int cmd, + void *arg) +{ + return -EINVAL; +} + static struct cdrom_device_ops gdrom_ops = { .open = gdrom_open, .release = gdrom_release, @@ -478,6 +484,7 @@ static struct cdrom_device_ops gdrom_ops = { .media_changed = gdrom_mediachanged, .get_last_session = gdrom_get_last_session, .reset = gdrom_hardreset, + .audio_ioctl = gdrom_audio_ioctl, .capability = CDC_MULTI_SESSION | CDC_MEDIA_CHANGED | CDC_RESET | CDC_DRIVE_STATUS | CDC_CD_R, .n_minors = 1, -- GitLab From bce31b674846584f0a80c95b6c09f07c32b9b041 Mon Sep 17 00:00:00 2001 From: Alexander Inyukhin Date: Mon, 18 Aug 2008 21:40:04 +0200 Subject: [PATCH 572/750] cdrom: handle TOC This patch should fix TOC handling for cdroms that can not play audio. It extends commit af744e3294d09d706c4eae26cffaaa68a8d40337 ("cdrom: don't check CDC_PLAY_AUDIO in cdrom_count_tracks()") with a safety check and non-audio ioctls support. Since CDC_PLAY_AUDIO flag was used not only to check ability to play audio but also to ensure that audio_ioctl was not NULL, all TOC-related operations had to use it. As far as I understand, now audio_ioctl is never NULL, so a sanity check during device registration should be sufficient. It was tested on Optiarc AD7203A device, that has no ability to play audio. Cc: Tejun Heo Cc: Jens Axboe Cc: Borislav Petkov Signed-off-by: Andrew Morton [bart: remove now unneeded ->audio_ioctl check (noticed by Borislav)] Signed-off-by: Bartlomiej Zolnierkiewicz --- drivers/cdrom/cdrom.c | 7 ------- 1 file changed, 7 deletions(-) diff --git a/drivers/cdrom/cdrom.c b/drivers/cdrom/cdrom.c index d9d1b65d206..74031de517e 100644 --- a/drivers/cdrom/cdrom.c +++ b/drivers/cdrom/cdrom.c @@ -408,7 +408,6 @@ int register_cdrom(struct cdrom_device_info *cdi) ENSURE(get_last_session, CDC_MULTI_SESSION); ENSURE(get_mcn, CDC_MCN); ENSURE(reset, CDC_RESET); - ENSURE(audio_ioctl, CDC_PLAY_AUDIO); ENSURE(generic_packet, CDC_GENERIC_PACKET); cdi->mc_flags = 0; cdo->n_minors = 0; @@ -2506,8 +2505,6 @@ static int cdrom_ioctl_get_subchnl(struct cdrom_device_info *cdi, /* cdinfo(CD_DO_IOCTL,"entering CDROMSUBCHNL\n");*/ - if (!CDROM_CAN(CDC_PLAY_AUDIO)) - return -ENOSYS; if (copy_from_user(&q, argp, sizeof(q))) return -EFAULT; @@ -2538,8 +2535,6 @@ static int cdrom_ioctl_read_tochdr(struct cdrom_device_info *cdi, /* cdinfo(CD_DO_IOCTL, "entering CDROMREADTOCHDR\n"); */ - if (!CDROM_CAN(CDC_PLAY_AUDIO)) - return -ENOSYS; if (copy_from_user(&header, argp, sizeof(header))) return -EFAULT; @@ -2562,8 +2557,6 @@ static int cdrom_ioctl_read_tocentry(struct cdrom_device_info *cdi, /* cdinfo(CD_DO_IOCTL, "entering CDROMREADTOCENTRY\n"); */ - if (!CDROM_CAN(CDC_PLAY_AUDIO)) - return -ENOSYS; if (copy_from_user(&entry, argp, sizeof(entry))) return -EFAULT; -- GitLab From fc99856a45cab8040f07d93d52fabd11834bf544 Mon Sep 17 00:00:00 2001 From: Adrian Bunk Date: Mon, 18 Aug 2008 21:40:04 +0200 Subject: [PATCH 573/750] ide-cd: use bcd2bin/bin2bcd Change ide-cd to use the new bcd2bin/bin2bcd functions instead of the obsolete BCD2BIN/BIN2BCD macros. Signed-off-by: Adrian Bunk Acked-by: Borislav Petkov Signed-off-by: Andrew Morton Signed-off-by: Bartlomiej Zolnierkiewicz --- drivers/ide/ide-cd.c | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) diff --git a/drivers/ide/ide-cd.c b/drivers/ide/ide-cd.c index 89a112d513a..49a8c589e34 100644 --- a/drivers/ide/ide-cd.c +++ b/drivers/ide/ide-cd.c @@ -1272,9 +1272,9 @@ static ide_startstop_t ide_cd_do_request(ide_drive_t *drive, struct request *rq, */ static void msf_from_bcd(struct atapi_msf *msf) { - msf->minute = BCD2BIN(msf->minute); - msf->second = BCD2BIN(msf->second); - msf->frame = BCD2BIN(msf->frame); + msf->minute = bcd2bin(msf->minute); + msf->second = bcd2bin(msf->second); + msf->frame = bcd2bin(msf->frame); } int cdrom_check_status(ide_drive_t *drive, struct request_sense *sense) @@ -1415,8 +1415,8 @@ int ide_cd_read_toc(ide_drive_t *drive, struct request_sense *sense) return stat; if (drive->atapi_flags & IDE_AFLAG_TOCTRACKS_AS_BCD) { - toc->hdr.first_track = BCD2BIN(toc->hdr.first_track); - toc->hdr.last_track = BCD2BIN(toc->hdr.last_track); + toc->hdr.first_track = bcd2bin(toc->hdr.first_track); + toc->hdr.last_track = bcd2bin(toc->hdr.last_track); } ntracks = toc->hdr.last_track - toc->hdr.first_track + 1; @@ -1456,8 +1456,8 @@ int ide_cd_read_toc(ide_drive_t *drive, struct request_sense *sense) return stat; if (drive->atapi_flags & IDE_AFLAG_TOCTRACKS_AS_BCD) { - toc->hdr.first_track = (u8)BIN2BCD(CDROM_LEADOUT); - toc->hdr.last_track = (u8)BIN2BCD(CDROM_LEADOUT); + toc->hdr.first_track = (u8)bin2bcd(CDROM_LEADOUT); + toc->hdr.last_track = (u8)bin2bcd(CDROM_LEADOUT); } else { toc->hdr.first_track = CDROM_LEADOUT; toc->hdr.last_track = CDROM_LEADOUT; @@ -1470,14 +1470,14 @@ int ide_cd_read_toc(ide_drive_t *drive, struct request_sense *sense) toc->hdr.toc_length = be16_to_cpu(toc->hdr.toc_length); if (drive->atapi_flags & IDE_AFLAG_TOCTRACKS_AS_BCD) { - toc->hdr.first_track = BCD2BIN(toc->hdr.first_track); - toc->hdr.last_track = BCD2BIN(toc->hdr.last_track); + toc->hdr.first_track = bcd2bin(toc->hdr.first_track); + toc->hdr.last_track = bcd2bin(toc->hdr.last_track); } for (i = 0; i <= ntracks; i++) { if (drive->atapi_flags & IDE_AFLAG_TOCADDR_AS_BCD) { if (drive->atapi_flags & IDE_AFLAG_TOCTRACKS_AS_BCD) - toc->ent[i].track = BCD2BIN(toc->ent[i].track); + toc->ent[i].track = bcd2bin(toc->ent[i].track); msf_from_bcd(&toc->ent[i].addr.msf); } toc->ent[i].addr.lba = msf_to_lba(toc->ent[i].addr.msf.minute, -- GitLab From 1b427a33b06ae76c64c1ad9af899a45b682ba6c6 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Mon, 18 Aug 2008 21:40:04 +0200 Subject: [PATCH 574/750] sgiioc4: fixup message on resource allocation failure There can be more than one sgiioc4 card in the system so print also PCI device name on resource allocation failure (so we know which one is the problematic one). Reported-by: Jeremy Higdon Signed-off-by: Bartlomiej Zolnierkiewicz --- drivers/ide/pci/sgiioc4.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/ide/pci/sgiioc4.c b/drivers/ide/pci/sgiioc4.c index 42eef19a18f..681306c9d79 100644 --- a/drivers/ide/pci/sgiioc4.c +++ b/drivers/ide/pci/sgiioc4.c @@ -621,9 +621,9 @@ sgiioc4_ide_setup_pci_device(struct pci_dev *dev) if (!request_mem_region(cmd_phys_base, IOC4_CMD_CTL_BLK_SIZE, DRV_NAME)) { printk(KERN_ERR - "%s : %s -- ERROR, Addresses " + "%s %s: -- ERROR, Addresses " "0x%p to 0x%p ALREADY in use\n", - __func__, DRV_NAME, (void *) cmd_phys_base, + DRV_NAME, pci_name(dev), (void *)cmd_phys_base, (void *) cmd_phys_base + IOC4_CMD_CTL_BLK_SIZE); return -ENOMEM; } -- GitLab From 37014c64079748c47fd109ef2d91ecd785a8c764 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Mon, 18 Aug 2008 21:40:05 +0200 Subject: [PATCH 575/750] ata: add missing ATA_ID_* defines (take 2) Add missing ATA_ID_* defines and update {ata,atapi}_*() inlines accordingly. The currently unused defines are needed for the forthcoming drivers/ide/ changes. v2: Add ATA_ID_SPG. Acked-by: Jeff Garzik Signed-off-by: Bartlomiej Zolnierkiewicz --- include/linux/ata.h | 122 +++++++++++++++++++++++++++----------------- 1 file changed, 76 insertions(+), 46 deletions(-) diff --git a/include/linux/ata.h b/include/linux/ata.h index 1c622e2b050..03fff6239b3 100644 --- a/include/linux/ata.h +++ b/include/linux/ata.h @@ -46,18 +46,48 @@ enum { ATA_MAX_SECTORS_TAPE = 65535, ATA_ID_WORDS = 256, + ATA_ID_CONFIG = 0, + ATA_ID_CYLS = 1, + ATA_ID_HEADS = 3, + ATA_ID_SECTORS = 6, ATA_ID_SERNO = 10, + ATA_ID_BUF_SIZE = 21, ATA_ID_FW_REV = 23, ATA_ID_PROD = 27, + ATA_ID_MAX_MULTSECT = 47, + ATA_ID_DWORD_IO = 48, + ATA_ID_CAPABILITY = 49, ATA_ID_OLD_PIO_MODES = 51, + ATA_ID_OLD_DMA_MODES = 52, ATA_ID_FIELD_VALID = 53, + ATA_ID_CUR_CYLS = 54, + ATA_ID_CUR_HEADS = 55, + ATA_ID_CUR_SECTORS = 56, + ATA_ID_MULTSECT = 59, + ATA_ID_LBA_CAPACITY = 60, + ATA_ID_SWDMA_MODES = 62, ATA_ID_MWDMA_MODES = 63, ATA_ID_PIO_MODES = 64, ATA_ID_EIDE_DMA_MIN = 65, + ATA_ID_EIDE_DMA_TIME = 66, ATA_ID_EIDE_PIO = 67, ATA_ID_EIDE_PIO_IORDY = 68, - ATA_ID_UDMA_MODES = 88, + ATA_ID_QUEUE_DEPTH = 75, ATA_ID_MAJOR_VER = 80, + ATA_ID_COMMAND_SET_1 = 82, + ATA_ID_COMMAND_SET_2 = 83, + ATA_ID_CFSSE = 84, + ATA_ID_CFS_ENABLE_1 = 85, + ATA_ID_CFS_ENABLE_2 = 86, + ATA_ID_CSF_DEFAULT = 87, + ATA_ID_UDMA_MODES = 88, + ATA_ID_HW_CONFIG = 93, + ATA_ID_SPG = 98, + ATA_ID_LBA_CAPACITY_2 = 100, + ATA_ID_LAST_LUN = 126, + ATA_ID_DLF = 128, + ATA_ID_CSFO = 129, + ATA_ID_CFA_POWER = 160, ATA_ID_PIO4 = (1 << 1), ATA_ID_SERNO_LEN = 20, @@ -438,17 +468,17 @@ static inline int ata_is_data(u8 prot) /* * id tests */ -#define ata_id_is_ata(id) (((id)[0] & (1 << 15)) == 0) -#define ata_id_has_lba(id) ((id)[49] & (1 << 9)) -#define ata_id_has_dma(id) ((id)[49] & (1 << 8)) +#define ata_id_is_ata(id) (((id)[ATA_ID_CONFIG] & (1 << 15)) == 0) +#define ata_id_has_lba(id) ((id)[ATA_ID_CAPABILITY] & (1 << 9)) +#define ata_id_has_dma(id) ((id)[ATA_ID_CAPABILITY] & (1 << 8)) #define ata_id_has_ncq(id) ((id)[76] & (1 << 8)) -#define ata_id_queue_depth(id) (((id)[75] & 0x1f) + 1) -#define ata_id_removeable(id) ((id)[0] & (1 << 7)) +#define ata_id_queue_depth(id) (((id)[ATA_ID_QUEUE_DEPTH] & 0x1f) + 1) +#define ata_id_removeable(id) ((id)[ATA_ID_CONFIG] & (1 << 7)) #define ata_id_has_atapi_AN(id) \ ( (((id)[76] != 0x0000) && ((id)[76] != 0xffff)) && \ ((id)[78] & (1 << 5)) ) -#define ata_id_iordy_disable(id) ((id)[49] & (1 << 10)) -#define ata_id_has_iordy(id) ((id)[49] & (1 << 11)) +#define ata_id_iordy_disable(id) ((id)[ATA_ID_CAPABILITY] & (1 << 10)) +#define ata_id_has_iordy(id) ((id)[ATA_ID_CAPABILITY] & (1 << 11)) #define ata_id_u32(id,n) \ (((u32) (id)[(n) + 1] << 16) | ((u32) (id)[(n)])) #define ata_id_u64(id,n) \ @@ -457,7 +487,7 @@ static inline int ata_is_data(u8 prot) ((u64) (id)[(n) + 1] << 16) | \ ((u64) (id)[(n) + 0]) ) -#define ata_id_cdb_intr(id) (((id)[0] & 0x60) == 0x20) +#define ata_id_cdb_intr(id) (((id)[ATA_ID_CONFIG] & 0x60) == 0x20) static inline bool ata_id_has_hipm(const u16 *id) { @@ -482,75 +512,75 @@ static inline bool ata_id_has_dipm(const u16 *id) static inline int ata_id_has_fua(const u16 *id) { - if ((id[84] & 0xC000) != 0x4000) + if ((id[ATA_ID_CFSSE] & 0xC000) != 0x4000) return 0; - return id[84] & (1 << 6); + return id[ATA_ID_CFSSE] & (1 << 6); } static inline int ata_id_has_flush(const u16 *id) { - if ((id[83] & 0xC000) != 0x4000) + if ((id[ATA_ID_COMMAND_SET_2] & 0xC000) != 0x4000) return 0; - return id[83] & (1 << 12); + return id[ATA_ID_COMMAND_SET_2] & (1 << 12); } static inline int ata_id_has_flush_ext(const u16 *id) { - if ((id[83] & 0xC000) != 0x4000) + if ((id[ATA_ID_COMMAND_SET_2] & 0xC000) != 0x4000) return 0; - return id[83] & (1 << 13); + return id[ATA_ID_COMMAND_SET_2] & (1 << 13); } static inline int ata_id_has_lba48(const u16 *id) { - if ((id[83] & 0xC000) != 0x4000) + if ((id[ATA_ID_COMMAND_SET_2] & 0xC000) != 0x4000) return 0; - if (!ata_id_u64(id, 100)) + if (!ata_id_u64(id, ATA_ID_LBA_CAPACITY_2)) return 0; - return id[83] & (1 << 10); + return id[ATA_ID_COMMAND_SET_2] & (1 << 10); } static inline int ata_id_hpa_enabled(const u16 *id) { /* Yes children, word 83 valid bits cover word 82 data */ - if ((id[83] & 0xC000) != 0x4000) + if ((id[ATA_ID_COMMAND_SET_2] & 0xC000) != 0x4000) return 0; /* And 87 covers 85-87 */ - if ((id[87] & 0xC000) != 0x4000) + if ((id[ATA_ID_CSF_DEFAULT] & 0xC000) != 0x4000) return 0; /* Check command sets enabled as well as supported */ - if ((id[85] & ( 1 << 10)) == 0) + if ((id[ATA_ID_CFS_ENABLE_1] & (1 << 10)) == 0) return 0; - return id[82] & (1 << 10); + return id[ATA_ID_COMMAND_SET_1] & (1 << 10); } static inline int ata_id_has_wcache(const u16 *id) { /* Yes children, word 83 valid bits cover word 82 data */ - if ((id[83] & 0xC000) != 0x4000) + if ((id[ATA_ID_COMMAND_SET_2] & 0xC000) != 0x4000) return 0; - return id[82] & (1 << 5); + return id[ATA_ID_COMMAND_SET_1] & (1 << 5); } static inline int ata_id_has_pm(const u16 *id) { - if ((id[83] & 0xC000) != 0x4000) + if ((id[ATA_ID_COMMAND_SET_2] & 0xC000) != 0x4000) return 0; - return id[82] & (1 << 3); + return id[ATA_ID_COMMAND_SET_1] & (1 << 3); } static inline int ata_id_rahead_enabled(const u16 *id) { - if ((id[87] & 0xC000) != 0x4000) + if ((id[ATA_ID_CSF_DEFAULT] & 0xC000) != 0x4000) return 0; - return id[85] & (1 << 6); + return id[ATA_ID_CFS_ENABLE_1] & (1 << 6); } static inline int ata_id_wcache_enabled(const u16 *id) { - if ((id[87] & 0xC000) != 0x4000) + if ((id[ATA_ID_CSF_DEFAULT] & 0xC000) != 0x4000) return 0; - return id[85] & (1 << 5); + return id[ATA_ID_CFS_ENABLE_1] & (1 << 5); } /** @@ -581,7 +611,7 @@ static inline unsigned int ata_id_major_version(const u16 *id) static inline int ata_id_is_sata(const u16 *id) { - return ata_id_major_version(id) >= 5 && id[93] == 0; + return ata_id_major_version(id) >= 5 && id[ATA_ID_HW_CONFIG] == 0; } static inline int ata_id_has_tpm(const u16 *id) @@ -599,7 +629,7 @@ static inline int ata_id_has_dword_io(const u16 *id) /* ATA 8 reuses this flag for "trusted" computing */ if (ata_id_major_version(id) > 7) return 0; - if (id[48] & (1 << 0)) + if (id[ATA_ID_DWORD_IO] & (1 << 0)) return 1; return 0; } @@ -608,22 +638,22 @@ static inline int ata_id_current_chs_valid(const u16 *id) { /* For ATA-1 devices, if the INITIALIZE DEVICE PARAMETERS command has not been issued to the device then the values of - id[54] to id[56] are vendor specific. */ - return (id[53] & 0x01) && /* Current translation valid */ - id[54] && /* cylinders in current translation */ - id[55] && /* heads in current translation */ - id[55] <= 16 && - id[56]; /* sectors in current translation */ + id[ATA_ID_CUR_CYLS] to id[ATA_ID_CUR_SECTORS] are vendor specific. */ + return (id[ATA_ID_FIELD_VALID] & 1) && /* Current translation valid */ + id[ATA_ID_CUR_CYLS] && /* cylinders in current translation */ + id[ATA_ID_CUR_HEADS] && /* heads in current translation */ + id[ATA_ID_CUR_HEADS] <= 16 && + id[ATA_ID_CUR_SECTORS]; /* sectors in current translation */ } static inline int ata_id_is_cfa(const u16 *id) { - u16 v = id[0]; - if (v == 0x848A) /* Standard CF */ + if (id[ATA_ID_CONFIG] == 0x848A) /* Standard CF */ return 1; /* Could be CF hiding as standard ATA */ - if (ata_id_major_version(id) >= 3 && id[82] != 0xFFFF && - (id[82] & ( 1 << 2))) + if (ata_id_major_version(id) >= 3 && + id[ATA_ID_COMMAND_SET_1] != 0xFFFF && + (id[ATA_ID_COMMAND_SET_1] & (1 << 2))) return 1; return 0; } @@ -632,21 +662,21 @@ static inline int ata_drive_40wire(const u16 *dev_id) { if (ata_id_is_sata(dev_id)) return 0; /* SATA */ - if ((dev_id[93] & 0xE000) == 0x6000) + if ((dev_id[ATA_ID_HW_CONFIG] & 0xE000) == 0x6000) return 0; /* 80 wire */ return 1; } static inline int ata_drive_40wire_relaxed(const u16 *dev_id) { - if ((dev_id[93] & 0x2000) == 0x2000) + if ((dev_id[ATA_ID_HW_CONFIG] & 0x2000) == 0x2000) return 0; /* 80 wire */ return 1; } static inline int atapi_cdb_len(const u16 *dev_id) { - u16 tmp = dev_id[0] & 0x3; + u16 tmp = dev_id[ATA_ID_CONFIG] & 0x3; switch (tmp) { case 0: return 12; case 1: return 16; @@ -656,7 +686,7 @@ static inline int atapi_cdb_len(const u16 *dev_id) static inline int atapi_command_packet_set(const u16 *dev_id) { - return (dev_id[0] >> 8) & 0x1f; + return (dev_id[ATA_ID_CONFIG] >> 8) & 0x1f; } static inline int atapi_id_dmadir(const u16 *dev_id) -- GitLab From 476d9894dde2da2c2b326d70b5bce5eccc593c8b Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Mon, 18 Aug 2008 21:40:05 +0200 Subject: [PATCH 576/750] ata: add missing ATA_CMD_* defines Add missing ATA_CMD_* defines to . Also add ATA_EXABYTE_ENABLE_NEST, SETFEATURES_AAM_* and ATA_SMART_* defines while at it. Partially based on earlier work by Chris Wedgwood. Acked-by: Chris Wedgwood Acked-by: Jeff Garzik Signed-off-by: Bartlomiej Zolnierkiewicz --- include/linux/ata.h | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+) diff --git a/include/linux/ata.h b/include/linux/ata.h index 03fff6239b3..cf4ef6d915a 100644 --- a/include/linux/ata.h +++ b/include/linux/ata.h @@ -222,6 +222,13 @@ enum { ATA_CMD_PMP_WRITE = 0xE8, ATA_CMD_CONF_OVERLAY = 0xB1, ATA_CMD_SEC_FREEZE_LOCK = 0xF5, + ATA_CMD_SMART = 0xB0, + ATA_CMD_MEDIA_LOCK = 0xDE, + ATA_CMD_MEDIA_UNLOCK = 0xDF, + /* marked obsolete in the ATA/ATAPI-7 spec */ + ATA_CMD_RESTORE = 0x10, + /* EXABYTE specific */ + ATA_EXABYTE_ENABLE_NEST = 0xF0, /* READ_LOG_EXT pages */ ATA_LOG_SATA_NCQ = 0x10, @@ -262,6 +269,10 @@ enum { SETFEATURES_WC_ON = 0x02, /* Enable write cache */ SETFEATURES_WC_OFF = 0x82, /* Disable write cache */ + /* Enable/Disable Automatic Acoustic Management */ + SETFEATURES_AAM_ON = 0x42, + SETFEATURES_AAM_OFF = 0xC2, + SETFEATURES_SPINUP = 0x07, /* Spin-up drive */ SETFEATURES_SATA_ENABLE = 0x10, /* Enable use of SATA feature */ @@ -284,6 +295,15 @@ enum { ATA_DCO_IDENTIFY = 0xC2, ATA_DCO_SET = 0xC3, + /* feature values for SMART */ + ATA_SMART_ENABLE = 0xD8, + ATA_SMART_READ_VALUES = 0xD0, + ATA_SMART_READ_THRESHOLDS = 0xD1, + + /* password used in LBA Mid / LBA High for executing SMART commands */ + ATA_SMART_LBAM_PASS = 0x4F, + ATA_SMART_LBAH_PASS = 0xC2, + /* ATAPI stuff */ ATAPI_PKT_DMA = (1 << 0), ATAPI_DMADIR = (1 << 2), /* ATAPI data dir: -- GitLab From b59116205c54c89df9cc80721b59e1e8d14488f1 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Mon, 18 Aug 2008 21:40:05 +0200 Subject: [PATCH 577/750] ata: add missing ATA_* defines Add missing ATA_* defines to . Also add ATAPI_{LFS,EOM,ILI,IO,CODE} defines while at it. Cc: Jeff Garzik Signed-off-by: Bartlomiej Zolnierkiewicz --- include/linux/ata.h | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/include/linux/ata.h b/include/linux/ata.h index cf4ef6d915a..1ce19c1ef0e 100644 --- a/include/linux/ata.h +++ b/include/linux/ata.h @@ -153,13 +153,26 @@ enum { ATA_BUSY = (1 << 7), /* BSY status bit */ ATA_DRDY = (1 << 6), /* device ready */ ATA_DF = (1 << 5), /* device fault */ + ATA_DSC = (1 << 4), /* drive seek complete */ ATA_DRQ = (1 << 3), /* data request i/o */ + ATA_CORR = (1 << 2), /* corrected data error */ + ATA_IDX = (1 << 1), /* index */ ATA_ERR = (1 << 0), /* have an error */ ATA_SRST = (1 << 2), /* software reset */ ATA_ICRC = (1 << 7), /* interface CRC error */ + ATA_BBK = ATA_ICRC, /* pre-EIDE: block marked bad */ ATA_UNC = (1 << 6), /* uncorrectable media error */ + ATA_MC = (1 << 5), /* media changed */ ATA_IDNF = (1 << 4), /* ID not found */ + ATA_MCR = (1 << 3), /* media change requested */ ATA_ABORTED = (1 << 2), /* command aborted */ + ATA_TRK0NF = (1 << 1), /* track 0 not found */ + ATA_AMNF = (1 << 0), /* address mark not found */ + ATAPI_LFS = 0xF0, /* last failed sense */ + ATAPI_EOM = ATA_TRK0NF, /* end of media */ + ATAPI_ILI = ATA_AMNF, /* illegal length indication */ + ATAPI_IO = (1 << 1), + ATAPI_COD = (1 << 0), /* ATA command block registers */ ATA_REG_DATA = 0x00, -- GitLab From e0d94beead4ef652ec1c066be886140eebb06d8b Mon Sep 17 00:00:00 2001 From: Jiri Slaby Date: Mon, 11 Aug 2008 17:47:40 +0200 Subject: [PATCH 578/750] PCI: acpi_pcihp: run _OSC on a root bridge _OSC should be ran on a root bridge instead of the device itself. Do this before touching OSHP since PCI fw specs states that _OSC should be preferred over OSHP (however if the device has OSHP but not _OSC -- not a root bridge -- it's not). Cc: kristen.c.accardi@intel.com Acked-by: Alex Chiang Signed-off-by: Jiri Slaby Signed-off-by: Jesse Barnes --- drivers/pci/hotplug/acpi_pcihp.c | 41 ++++++++++++++++++++++---------- 1 file changed, 29 insertions(+), 12 deletions(-) diff --git a/drivers/pci/hotplug/acpi_pcihp.c b/drivers/pci/hotplug/acpi_pcihp.c index 93e37f0666a..bd831970f00 100644 --- a/drivers/pci/hotplug/acpi_pcihp.c +++ b/drivers/pci/hotplug/acpi_pcihp.c @@ -382,7 +382,7 @@ EXPORT_SYMBOL_GPL(acpi_get_hp_params_from_firmware); int acpi_get_hp_hw_control_from_firmware(struct pci_dev *dev, u32 flags) { acpi_status status; - acpi_handle chandle, handle = DEVICE_ACPI_HANDLE(&(dev->dev)); + acpi_handle chandle, handle; struct pci_dev *pdev = dev; struct pci_bus *parent; struct acpi_buffer string = { ACPI_ALLOCATE_BUFFER, NULL }; @@ -399,10 +399,28 @@ int acpi_get_hp_hw_control_from_firmware(struct pci_dev *dev, u32 flags) * Per PCI firmware specification, we should run the ACPI _OSC * method to get control of hotplug hardware before using it. If * an _OSC is missing, we look for an OSHP to do the same thing. - * To handle different BIOS behavior, we look for _OSC and OSHP - * within the scope of the hotplug controller and its parents, + * To handle different BIOS behavior, we look for _OSC on a root + * bridge preferentially (according to PCI fw spec). Later for + * OSHP within the scope of the hotplug controller and its parents, * upto the host bridge under which this controller exists. */ + while (pdev->bus->self) + pdev = pdev->bus->self; + handle = acpi_get_pci_rootbridge_handle(pci_domain_nr(pdev->bus), + pdev->bus->number); + if (handle) { + acpi_get_name(handle, ACPI_FULL_PATHNAME, &string); + dbg("Trying to get hotplug control for %s\n", + (char *)string.pointer); + status = pci_osc_control_set(handle, flags); + if (ACPI_SUCCESS(status)) + goto got_one; + kfree(string.pointer); + string = (struct acpi_buffer){ ACPI_ALLOCATE_BUFFER, NULL }; + } + + pdev = dev; + handle = DEVICE_ACPI_HANDLE(&dev->dev); while (!handle) { /* * This hotplug controller was not listed in the ACPI name @@ -427,15 +445,9 @@ int acpi_get_hp_hw_control_from_firmware(struct pci_dev *dev, u32 flags) acpi_get_name(handle, ACPI_FULL_PATHNAME, &string); dbg("Trying to get hotplug control for %s \n", (char *)string.pointer); - status = pci_osc_control_set(handle, flags); - if (status == AE_NOT_FOUND) - status = acpi_run_oshp(handle); - if (ACPI_SUCCESS(status)) { - dbg("Gained control for hotplug HW for pci %s (%s)\n", - pci_name(dev), (char *)string.pointer); - kfree(string.pointer); - return 0; - } + status = acpi_run_oshp(handle); + if (ACPI_SUCCESS(status)) + goto got_one; if (acpi_root_bridge(handle)) break; chandle = handle; @@ -449,6 +461,11 @@ int acpi_get_hp_hw_control_from_firmware(struct pci_dev *dev, u32 flags) kfree(string.pointer); return -ENODEV; +got_one: + dbg("Gained control for hotplug HW for pci %s (%s)\n", pci_name(dev), + (char *)string.pointer); + kfree(string.pointer); + return 0; } EXPORT_SYMBOL(acpi_get_hp_hw_control_from_firmware); -- GitLab From 056c58e8eb4d6765214757e541b68095e2eb2bd2 Mon Sep 17 00:00:00 2001 From: Jiri Slaby Date: Mon, 18 Aug 2008 20:22:54 +0200 Subject: [PATCH 579/750] PCI: add acpi_find_root_bridge_handle Consolidate finding of a root bridge and getting its handle to the one inline function. It's cut & pasted on multiple places. Use this new inline in those. Cc: kristen.c.accardi@intel.com Acked-by: Alex Chiang Signed-off-by: Jiri Slaby Signed-off-by: Jesse Barnes --- drivers/pci/hotplug/acpi_pcihp.c | 5 +---- drivers/pci/pcie/aer/aerdrv_acpi.c | 7 +------ include/linux/pci-acpi.h | 11 +++++++++++ 3 files changed, 13 insertions(+), 10 deletions(-) diff --git a/drivers/pci/hotplug/acpi_pcihp.c b/drivers/pci/hotplug/acpi_pcihp.c index bd831970f00..e17ef54f0ef 100644 --- a/drivers/pci/hotplug/acpi_pcihp.c +++ b/drivers/pci/hotplug/acpi_pcihp.c @@ -404,10 +404,7 @@ int acpi_get_hp_hw_control_from_firmware(struct pci_dev *dev, u32 flags) * OSHP within the scope of the hotplug controller and its parents, * upto the host bridge under which this controller exists. */ - while (pdev->bus->self) - pdev = pdev->bus->self; - handle = acpi_get_pci_rootbridge_handle(pci_domain_nr(pdev->bus), - pdev->bus->number); + handle = acpi_find_root_bridge_handle(pdev); if (handle) { acpi_get_name(handle, ACPI_FULL_PATHNAME, &string); dbg("Trying to get hotplug control for %s\n", diff --git a/drivers/pci/pcie/aer/aerdrv_acpi.c b/drivers/pci/pcie/aer/aerdrv_acpi.c index 30f581b8791..6dd7b13e980 100644 --- a/drivers/pci/pcie/aer/aerdrv_acpi.c +++ b/drivers/pci/pcie/aer/aerdrv_acpi.c @@ -36,12 +36,7 @@ int aer_osc_setup(struct pcie_device *pciedev) if (acpi_pci_disabled) return -1; - /* Find root host bridge */ - while (pdev->bus->self) - pdev = pdev->bus->self; - handle = acpi_get_pci_rootbridge_handle( - pci_domain_nr(pdev->bus), pdev->bus->number); - + handle = acpi_find_root_bridge_handle(pdev); if (handle) { pcie_osc_support_set(OSC_EXT_PCI_CONFIG_SUPPORT); status = pci_osc_control_set(handle, diff --git a/include/linux/pci-acpi.h b/include/linux/pci-acpi.h index 3ba25065fa9..8837928fbf3 100644 --- a/include/linux/pci-acpi.h +++ b/include/linux/pci-acpi.h @@ -57,6 +57,15 @@ static inline acpi_status pcie_osc_support_set(u32 flags) { return __pci_osc_support_set(flags, PCI_EXPRESS_ROOT_HID_STRING); } +static inline acpi_handle acpi_find_root_bridge_handle(struct pci_dev *pdev) +{ + /* Find root host bridge */ + while (pdev->bus->self) + pdev = pdev->bus->self; + + return acpi_get_pci_rootbridge_handle(pci_domain_nr(pdev->bus), + pdev->bus->number); +} #else #if !defined(AE_ERROR) typedef u32 acpi_status; @@ -66,6 +75,8 @@ static inline acpi_status pci_osc_control_set(acpi_handle handle, u32 flags) {return AE_ERROR;} static inline acpi_status pci_osc_support_set(u32 flags) {return AE_ERROR;} static inline acpi_status pcie_osc_support_set(u32 flags) {return AE_ERROR;} +static inline acpi_handle acpi_find_root_bridge_handle(struct pci_dev *pdev) +{ return NULL; } #endif #endif /* _PCI_ACPI_H_ */ -- GitLab From ea42b8ce8cc9f4a3d3048fae5ba8ad7269d17afa Mon Sep 17 00:00:00 2001 From: Robin Holt Date: Fri, 15 Aug 2008 04:56:01 -0500 Subject: [PATCH 580/750] [IA64] Remove sn2_defconfig. Not really a patch as much as a remove this file request. Now that generic_defconfig supports all the configurations SGI currently supports and has NR_CPUS and NR_NODES at our largest configurations, we have no reason to maintain the extra defconfig file. Signed-off-by: Robin Holt Acked-by: Jack Steiner Signed-off-by: Jes Sorensen Signed-off-by: Tony Luck --- arch/ia64/configs/sn2_defconfig | 1285 ------------------------------- 1 file changed, 1285 deletions(-) delete mode 100644 arch/ia64/configs/sn2_defconfig diff --git a/arch/ia64/configs/sn2_defconfig b/arch/ia64/configs/sn2_defconfig deleted file mode 100644 index 7f6b2377d13..00000000000 --- a/arch/ia64/configs/sn2_defconfig +++ /dev/null @@ -1,1285 +0,0 @@ -# -# Automatically generated make config: don't edit -# Linux kernel version: 2.6.23 -# Thu Oct 18 16:03:40 2007 -# -CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" - -# -# General setup -# -CONFIG_EXPERIMENTAL=y -CONFIG_LOCK_KERNEL=y -CONFIG_INIT_ENV_ARG_LIMIT=32 -CONFIG_LOCALVERSION="" -# CONFIG_LOCALVERSION_AUTO is not set -CONFIG_SWAP=y -CONFIG_SYSVIPC=y -CONFIG_SYSVIPC_SYSCTL=y -CONFIG_POSIX_MQUEUE=y -# CONFIG_BSD_PROCESS_ACCT is not set -CONFIG_TASKSTATS=y -# CONFIG_TASK_DELAY_ACCT is not set -CONFIG_TASK_XACCT=y -CONFIG_TASK_IO_ACCOUNTING=y -# CONFIG_USER_NS is not set -# CONFIG_AUDIT is not set -# CONFIG_IKCONFIG is not set -CONFIG_LOG_BUF_SHIFT=20 -CONFIG_CGROUPS=y -CONFIG_CPUSETS=y -CONFIG_FAIR_GROUP_SCHED=y -CONFIG_FAIR_USER_SCHED=y -CONFIG_SYSFS_DEPRECATED=y -CONFIG_RELAY=y -CONFIG_BLK_DEV_INITRD=y -CONFIG_INITRAMFS_SOURCE="" -CONFIG_CC_OPTIMIZE_FOR_SIZE=y -CONFIG_SYSCTL=y -# CONFIG_EMBEDDED is not set -CONFIG_SYSCTL_SYSCALL=y -CONFIG_KALLSYMS=y -CONFIG_KALLSYMS_ALL=y -# CONFIG_KALLSYMS_EXTRA_PASS is not set -CONFIG_HOTPLUG=y -CONFIG_PRINTK=y -CONFIG_BUG=y -CONFIG_ELF_CORE=y -CONFIG_BASE_FULL=y -CONFIG_FUTEX=y -CONFIG_ANON_INODES=y -CONFIG_EPOLL=y -CONFIG_SIGNALFD=y -CONFIG_EVENTFD=y -CONFIG_SHMEM=y -CONFIG_VM_EVENT_COUNTERS=y -CONFIG_SLUB_DEBUG=y -# CONFIG_SLAB is not set -CONFIG_SLUB=y -# CONFIG_SLOB is not set -CONFIG_RT_MUTEXES=y -# CONFIG_TINY_SHMEM is not set -CONFIG_BASE_SMALL=0 -CONFIG_MODULES=y -CONFIG_MODULE_UNLOAD=y -# CONFIG_MODULE_FORCE_UNLOAD is not set -# CONFIG_MODVERSIONS is not set -# CONFIG_MODULE_SRCVERSION_ALL is not set -CONFIG_KMOD=y -CONFIG_STOP_MACHINE=y -CONFIG_BLOCK=y -# CONFIG_BLK_DEV_IO_TRACE is not set -CONFIG_BLK_DEV_BSG=y -CONFIG_BLOCK_COMPAT=y - -# -# IO Schedulers -# -CONFIG_IOSCHED_NOOP=y -CONFIG_IOSCHED_AS=y -CONFIG_IOSCHED_DEADLINE=y -CONFIG_IOSCHED_CFQ=y -CONFIG_DEFAULT_AS=y -# CONFIG_DEFAULT_DEADLINE is not set -# CONFIG_DEFAULT_CFQ is not set -# CONFIG_DEFAULT_NOOP is not set -CONFIG_DEFAULT_IOSCHED="anticipatory" - -# -# Processor type and features -# -CONFIG_IA64=y -CONFIG_64BIT=y -CONFIG_QUICKLIST=y -CONFIG_MMU=y -CONFIG_RWSEM_XCHGADD_ALGORITHM=y -# CONFIG_ARCH_HAS_ILOG2_U32 is not set -# CONFIG_ARCH_HAS_ILOG2_U64 is not set -CONFIG_HUGETLB_PAGE_SIZE_VARIABLE=y -CONFIG_GENERIC_FIND_NEXT_BIT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y -CONFIG_GENERIC_TIME=y -CONFIG_GENERIC_TIME_VSYSCALL=y -CONFIG_DMI=y -CONFIG_EFI=y -CONFIG_GENERIC_IOMAP=y -CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y -CONFIG_IA64_UNCACHED_ALLOCATOR=y -CONFIG_AUDIT_ARCH=y -# CONFIG_IA64_GENERIC is not set -# CONFIG_IA64_DIG is not set -# CONFIG_IA64_HP_ZX1 is not set -# CONFIG_IA64_HP_ZX1_SWIOTLB is not set -CONFIG_IA64_SGI_SN2=y -# CONFIG_IA64_HP_SIM is not set -# CONFIG_ITANIUM is not set -CONFIG_MCKINLEY=y -# CONFIG_IA64_PAGE_SIZE_4KB is not set -# CONFIG_IA64_PAGE_SIZE_8KB is not set -# CONFIG_IA64_PAGE_SIZE_16KB is not set -CONFIG_IA64_PAGE_SIZE_64KB=y -CONFIG_PGTABLE_3=y -# CONFIG_PGTABLE_4 is not set -# CONFIG_HZ_100 is not set -CONFIG_HZ_250=y -# CONFIG_HZ_300 is not set -# CONFIG_HZ_1000 is not set -CONFIG_HZ=250 -CONFIG_IA64_L1_CACHE_SHIFT=7 -# CONFIG_IA64_CYCLONE is not set -CONFIG_IOSAPIC=y -CONFIG_IA64_SGI_SN_XP=m -CONFIG_FORCE_MAX_ZONEORDER=17 -CONFIG_SMP=y -CONFIG_NR_CPUS=1024 -# CONFIG_HOTPLUG_CPU is not set -CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y -CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y -CONFIG_SCHED_SMT=y -CONFIG_PREEMPT_NONE=y -# CONFIG_PREEMPT_VOLUNTARY is not set -# CONFIG_PREEMPT is not set -CONFIG_PREEMPT_BKL=y -CONFIG_SELECT_MEMORY_MODEL=y -# CONFIG_FLATMEM_MANUAL is not set -CONFIG_DISCONTIGMEM_MANUAL=y -# CONFIG_SPARSEMEM_MANUAL is not set -CONFIG_DISCONTIGMEM=y -CONFIG_FLAT_NODE_MEM_MAP=y -CONFIG_NEED_MULTIPLE_NODES=y -# CONFIG_SPARSEMEM_STATIC is not set -CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y -CONFIG_SPLIT_PTLOCK_CPUS=4 -CONFIG_MIGRATION=y -CONFIG_RESOURCES_64BIT=y -CONFIG_ZONE_DMA_FLAG=0 -CONFIG_NR_QUICK=1 -CONFIG_VIRT_TO_BUS=y -CONFIG_ARCH_SELECT_MEMORY_MODEL=y -CONFIG_ARCH_DISCONTIGMEM_ENABLE=y -CONFIG_ARCH_FLATMEM_ENABLE=y -CONFIG_ARCH_SPARSEMEM_ENABLE=y -CONFIG_ARCH_DISCONTIGMEM_DEFAULT=y -CONFIG_NUMA=y -CONFIG_NODES_SHIFT=10 -CONFIG_ARCH_POPULATES_NODE_MAP=y -CONFIG_VIRTUAL_MEM_MAP=y -CONFIG_HOLES_IN_ZONE=y -CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID=y -CONFIG_HAVE_ARCH_NODEDATA_EXTENSION=y -CONFIG_IA32_SUPPORT=y -CONFIG_COMPAT=y -CONFIG_COMPAT_FOR_U64_ALIGNMENT=y -CONFIG_IA64_MCA_RECOVERY=y -CONFIG_PERFMON=y -CONFIG_IA64_PALINFO=y -CONFIG_IA64_MC_ERR_INJECT=y -CONFIG_SGI_SN=y -# CONFIG_IA64_ESI is not set -# CONFIG_IA64_HP_AML_NFW is not set - -# -# SN Devices -# -CONFIG_SGI_IOC3=y - -# -# Firmware Drivers -# -CONFIG_EFI_VARS=y -CONFIG_EFI_PCDP=y -CONFIG_DMIID=y -CONFIG_BINFMT_ELF=y -# CONFIG_BINFMT_MISC is not set - -# -# Power management and ACPI -# -CONFIG_PM=y -# CONFIG_PM_LEGACY is not set -# CONFIG_PM_DEBUG is not set -CONFIG_ACPI=y -# CONFIG_ACPI_PROCFS is not set -CONFIG_ACPI_PROC_EVENT=y -# CONFIG_ACPI_BUTTON is not set -# CONFIG_ACPI_FAN is not set -# CONFIG_ACPI_DOCK is not set -# CONFIG_ACPI_PROCESSOR is not set -CONFIG_ACPI_NUMA=y -CONFIG_ACPI_BLACKLIST_YEAR=0 -# CONFIG_ACPI_DEBUG is not set -CONFIG_ACPI_EC=y -CONFIG_ACPI_POWER=y -CONFIG_ACPI_SYSTEM=y -# CONFIG_ACPI_CONTAINER is not set - -# -# CPU Frequency scaling -# -# CONFIG_CPU_FREQ is not set - -# -# Bus options (PCI, PCMCIA) -# -CONFIG_PCI=y -CONFIG_PCI_DOMAINS=y -CONFIG_PCI_SYSCALL=y -CONFIG_PCIEPORTBUS=y -CONFIG_HOTPLUG_PCI_PCIE=y -CONFIG_PCIEAER=y -CONFIG_ARCH_SUPPORTS_MSI=y -# CONFIG_PCI_MSI is not set -# CONFIG_PCI_DEBUG is not set -CONFIG_HOTPLUG_PCI=y -# CONFIG_HOTPLUG_PCI_FAKE is not set -# CONFIG_HOTPLUG_PCI_ACPI is not set -# CONFIG_HOTPLUG_PCI_CPCI is not set -# CONFIG_HOTPLUG_PCI_SHPC is not set -CONFIG_HOTPLUG_PCI_SGI=y -# CONFIG_PCCARD is not set - -# -# Networking -# -CONFIG_NET=y - -# -# Networking options -# -CONFIG_PACKET=y -CONFIG_PACKET_MMAP=y -CONFIG_UNIX=y -CONFIG_XFRM=y -# CONFIG_XFRM_USER is not set -# CONFIG_XFRM_SUB_POLICY is not set -# CONFIG_XFRM_MIGRATE is not set -# CONFIG_NET_KEY is not set -CONFIG_INET=y -CONFIG_IP_MULTICAST=y -# CONFIG_IP_ADVANCED_ROUTER is not set -CONFIG_IP_FIB_HASH=y -# CONFIG_IP_PNP is not set -# CONFIG_NET_IPIP is not set -# CONFIG_NET_IPGRE is not set -# CONFIG_IP_MROUTE is not set -# CONFIG_ARPD is not set -CONFIG_SYN_COOKIES=y -# CONFIG_INET_AH is not set -# CONFIG_INET_ESP is not set -# CONFIG_INET_IPCOMP is not set -# CONFIG_INET_XFRM_TUNNEL is not set -CONFIG_INET_TUNNEL=m -CONFIG_INET_XFRM_MODE_TRANSPORT=y -CONFIG_INET_XFRM_MODE_TUNNEL=y -CONFIG_INET_XFRM_MODE_BEET=y -CONFIG_INET_LRO=y -CONFIG_INET_DIAG=m -CONFIG_INET_TCP_DIAG=m -# CONFIG_TCP_CONG_ADVANCED is not set -CONFIG_TCP_CONG_CUBIC=y -CONFIG_DEFAULT_TCP_CONG="cubic" -# CONFIG_TCP_MD5SIG is not set -CONFIG_IPV6=m -# CONFIG_IPV6_PRIVACY is not set -# CONFIG_IPV6_ROUTER_PREF is not set -# CONFIG_IPV6_OPTIMISTIC_DAD is not set -# CONFIG_INET6_AH is not set -# CONFIG_INET6_ESP is not set -# CONFIG_INET6_IPCOMP is not set -# CONFIG_IPV6_MIP6 is not set -# CONFIG_INET6_XFRM_TUNNEL is not set -# CONFIG_INET6_TUNNEL is not set -CONFIG_INET6_XFRM_MODE_TRANSPORT=m -CONFIG_INET6_XFRM_MODE_TUNNEL=m -CONFIG_INET6_XFRM_MODE_BEET=m -# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set -CONFIG_IPV6_SIT=m -# CONFIG_IPV6_TUNNEL is not set -# CONFIG_IPV6_MULTIPLE_TABLES is not set -# CONFIG_NETWORK_SECMARK is not set -# CONFIG_NETFILTER is not set -# CONFIG_IP_DCCP is not set -# CONFIG_IP_SCTP is not set -# CONFIG_TIPC is not set -# CONFIG_ATM is not set -# CONFIG_BRIDGE is not set -# CONFIG_VLAN_8021Q is not set -# CONFIG_DECNET is not set -# CONFIG_LLC2 is not set -# CONFIG_IPX is not set -# CONFIG_ATALK is not set -# CONFIG_X25 is not set -# CONFIG_LAPB is not set -# CONFIG_ECONET is not set -# CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# -# CONFIG_NET_SCHED is not set - -# -# Network testing -# -# CONFIG_NET_PKTGEN is not set -# CONFIG_HAMRADIO is not set -# CONFIG_IRDA is not set -# CONFIG_BT is not set -# CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -# CONFIG_WIRELESS_EXT is not set -# CONFIG_MAC80211 is not set -# CONFIG_IEEE80211 is not set -# CONFIG_RFKILL is not set -# CONFIG_NET_9P is not set - -# -# Device Drivers -# - -# -# Generic Driver Options -# -CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" -CONFIG_STANDALONE=y -CONFIG_PREVENT_FIRMWARE_BUILD=y -CONFIG_FW_LOADER=y -# CONFIG_DEBUG_DRIVER is not set -# CONFIG_DEBUG_DEVRES is not set -# CONFIG_SYS_HYPERVISOR is not set -# CONFIG_CONNECTOR is not set -# CONFIG_MTD is not set -# CONFIG_PARPORT is not set -CONFIG_PNP=y -# CONFIG_PNP_DEBUG is not set - -# -# Protocols -# -CONFIG_PNPACPI=y -CONFIG_BLK_DEV=y -# CONFIG_BLK_CPQ_DA is not set -# CONFIG_BLK_CPQ_CISS_DA is not set -# CONFIG_BLK_DEV_DAC960 is not set -# CONFIG_BLK_DEV_UMEM is not set -# CONFIG_BLK_DEV_COW_COMMON is not set -CONFIG_BLK_DEV_LOOP=y -CONFIG_BLK_DEV_CRYPTOLOOP=m -CONFIG_BLK_DEV_NBD=m -# CONFIG_BLK_DEV_SX8 is not set -# CONFIG_BLK_DEV_UB is not set -CONFIG_BLK_DEV_RAM=y -CONFIG_BLK_DEV_RAM_COUNT=16 -CONFIG_BLK_DEV_RAM_SIZE=4096 -CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 -# CONFIG_CDROM_PKTCDVD is not set -CONFIG_ATA_OVER_ETH=m -CONFIG_MISC_DEVICES=y -# CONFIG_PHANTOM is not set -# CONFIG_EEPROM_93CX6 is not set -CONFIG_SGI_IOC4=y -# CONFIG_TIFM_CORE is not set -CONFIG_IDE=y -CONFIG_IDE_MAX_HWIFS=4 -CONFIG_BLK_DEV_IDE=y - -# -# Please see Documentation/ide.txt for help/info on IDE drives -# -# CONFIG_BLK_DEV_IDE_SATA is not set -CONFIG_BLK_DEV_IDEDISK=y -# CONFIG_IDEDISK_MULTI_MODE is not set -CONFIG_BLK_DEV_IDECD=y -# CONFIG_BLK_DEV_IDETAPE is not set -# CONFIG_BLK_DEV_IDEFLOPPY is not set -# CONFIG_BLK_DEV_IDESCSI is not set -# CONFIG_BLK_DEV_IDEACPI is not set -# CONFIG_IDE_TASK_IOCTL is not set -CONFIG_IDE_PROC_FS=y - -# -# IDE chipset support/bugfixes -# -CONFIG_IDE_GENERIC=y -# CONFIG_BLK_DEV_PLATFORM is not set -# CONFIG_BLK_DEV_IDEPNP is not set - -# -# PCI IDE chipsets support -# -CONFIG_BLK_DEV_IDEPCI=y -CONFIG_IDEPCI_SHARE_IRQ=y -CONFIG_IDEPCI_PCIBUS_ORDER=y -# CONFIG_BLK_DEV_OFFBOARD is not set -# CONFIG_BLK_DEV_GENERIC is not set -# CONFIG_BLK_DEV_OPTI621 is not set -CONFIG_BLK_DEV_IDEDMA_PCI=y -# CONFIG_BLK_DEV_AEC62XX is not set -# CONFIG_BLK_DEV_ALI15X3 is not set -# CONFIG_BLK_DEV_AMD74XX is not set -# CONFIG_BLK_DEV_CMD64X is not set -# CONFIG_BLK_DEV_TRIFLEX is not set -# CONFIG_BLK_DEV_CY82C693 is not set -# CONFIG_BLK_DEV_CS5520 is not set -# CONFIG_BLK_DEV_CS5530 is not set -# CONFIG_BLK_DEV_HPT34X is not set -# CONFIG_BLK_DEV_HPT366 is not set -# CONFIG_BLK_DEV_JMICRON is not set -# CONFIG_BLK_DEV_SC1200 is not set -# CONFIG_BLK_DEV_PIIX is not set -# CONFIG_BLK_DEV_IT8213 is not set -# CONFIG_BLK_DEV_IT821X is not set -# CONFIG_BLK_DEV_NS87415 is not set -# CONFIG_BLK_DEV_PDC202XX_OLD is not set -# CONFIG_BLK_DEV_PDC202XX_NEW is not set -# CONFIG_BLK_DEV_SVWKS is not set -CONFIG_BLK_DEV_SGIIOC4=y -# CONFIG_BLK_DEV_SIIMAGE is not set -# CONFIG_BLK_DEV_SLC90E66 is not set -# CONFIG_BLK_DEV_TRM290 is not set -# CONFIG_BLK_DEV_VIA82CXXX is not set -# CONFIG_BLK_DEV_TC86C001 is not set -# CONFIG_IDE_ARM is not set -CONFIG_BLK_DEV_IDEDMA=y -# CONFIG_BLK_DEV_HD is not set - -# -# SCSI device support -# -# CONFIG_RAID_ATTRS is not set -CONFIG_SCSI=y -CONFIG_SCSI_DMA=y -# CONFIG_SCSI_TGT is not set -CONFIG_SCSI_NETLINK=y -CONFIG_SCSI_PROC_FS=y - -# -# SCSI support type (disk, tape, CD-ROM) -# -CONFIG_BLK_DEV_SD=y -CONFIG_CHR_DEV_ST=m -# CONFIG_CHR_DEV_OSST is not set -CONFIG_BLK_DEV_SR=m -# CONFIG_BLK_DEV_SR_VENDOR is not set -CONFIG_CHR_DEV_SG=m -CONFIG_CHR_DEV_SCH=m - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# -# CONFIG_SCSI_MULTI_LUN is not set -CONFIG_SCSI_CONSTANTS=y -# CONFIG_SCSI_LOGGING is not set -# CONFIG_SCSI_SCAN_ASYNC is not set -CONFIG_SCSI_WAIT_SCAN=m - -# -# SCSI Transports -# -CONFIG_SCSI_SPI_ATTRS=y -CONFIG_SCSI_FC_ATTRS=y -CONFIG_SCSI_ISCSI_ATTRS=m -CONFIG_SCSI_SAS_ATTRS=y -CONFIG_SCSI_SAS_LIBSAS=y -# CONFIG_SCSI_SAS_ATA is not set -# CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set -CONFIG_SCSI_SRP_ATTRS=y -CONFIG_SCSI_LOWLEVEL=y -CONFIG_ISCSI_TCP=m -# CONFIG_BLK_DEV_3W_XXXX_RAID is not set -# CONFIG_SCSI_3W_9XXX is not set -# CONFIG_SCSI_ACARD is not set -# CONFIG_SCSI_AACRAID is not set -# CONFIG_SCSI_AIC7XXX is not set -# CONFIG_SCSI_AIC7XXX_OLD is not set -# CONFIG_SCSI_AIC79XX is not set -# CONFIG_SCSI_AIC94XX is not set -# CONFIG_SCSI_ADVANSYS is not set -# CONFIG_SCSI_ARCMSR is not set -# CONFIG_MEGARAID_NEWGEN is not set -# CONFIG_MEGARAID_LEGACY is not set -# CONFIG_MEGARAID_SAS is not set -# CONFIG_SCSI_HPTIOP is not set -# CONFIG_SCSI_DMX3191D is not set -# CONFIG_SCSI_FUTURE_DOMAIN is not set -# CONFIG_SCSI_IPS is not set -# CONFIG_SCSI_INITIO is not set -# CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_STEX is not set -# CONFIG_SCSI_SYM53C8XX_2 is not set -# CONFIG_SCSI_IPR is not set -CONFIG_SCSI_QLOGIC_1280=y -CONFIG_SCSI_QLA_FC=y -# CONFIG_SCSI_QLA_ISCSI is not set -# CONFIG_SCSI_LPFC is not set -# CONFIG_SCSI_DC395x is not set -# CONFIG_SCSI_DC390T is not set -# CONFIG_SCSI_DEBUG is not set -# CONFIG_SCSI_SRP is not set -CONFIG_ATA=y -CONFIG_ATA_NONSTANDARD=y -CONFIG_ATA_ACPI=y -# CONFIG_SATA_AHCI is not set -# CONFIG_SATA_SVW is not set -# CONFIG_ATA_PIIX is not set -# CONFIG_SATA_MV is not set -# CONFIG_SATA_NV is not set -# CONFIG_PDC_ADMA is not set -# CONFIG_SATA_QSTOR is not set -# CONFIG_SATA_PROMISE is not set -# CONFIG_SATA_SX4 is not set -# CONFIG_SATA_SIL is not set -# CONFIG_SATA_SIL24 is not set -# CONFIG_SATA_SIS is not set -# CONFIG_SATA_ULI is not set -# CONFIG_SATA_VIA is not set -CONFIG_SATA_VITESSE=y -# CONFIG_SATA_INIC162X is not set -# CONFIG_PATA_ACPI is not set -# CONFIG_PATA_ALI is not set -# CONFIG_PATA_AMD is not set -# CONFIG_PATA_ARTOP is not set -# CONFIG_PATA_ATIIXP is not set -# CONFIG_PATA_CMD640_PCI is not set -# CONFIG_PATA_CMD64X is not set -# CONFIG_PATA_CS5520 is not set -# CONFIG_PATA_CS5530 is not set -# CONFIG_PATA_CYPRESS is not set -# CONFIG_PATA_EFAR is not set -# CONFIG_ATA_GENERIC is not set -# CONFIG_PATA_HPT366 is not set -# CONFIG_PATA_HPT37X is not set -# CONFIG_PATA_HPT3X2N is not set -# CONFIG_PATA_HPT3X3 is not set -# CONFIG_PATA_IT821X is not set -# CONFIG_PATA_IT8213 is not set -# CONFIG_PATA_JMICRON is not set -# CONFIG_PATA_TRIFLEX is not set -# CONFIG_PATA_MARVELL is not set -# CONFIG_PATA_MPIIX is not set -# CONFIG_PATA_OLDPIIX is not set -# CONFIG_PATA_NETCELL is not set -# CONFIG_PATA_NS87410 is not set -# CONFIG_PATA_NS87415 is not set -# CONFIG_PATA_OPTI is not set -# CONFIG_PATA_OPTIDMA is not set -# CONFIG_PATA_PDC_OLD is not set -# CONFIG_PATA_RADISYS is not set -# CONFIG_PATA_RZ1000 is not set -# CONFIG_PATA_SC1200 is not set -# CONFIG_PATA_SERVERWORKS is not set -# CONFIG_PATA_PDC2027X is not set -# CONFIG_PATA_SIL680 is not set -# CONFIG_PATA_SIS is not set -# CONFIG_PATA_VIA is not set -# CONFIG_PATA_WINBOND is not set -CONFIG_MD=y -CONFIG_BLK_DEV_MD=y -CONFIG_MD_LINEAR=y -CONFIG_MD_RAID0=y -CONFIG_MD_RAID1=y -# CONFIG_MD_RAID10 is not set -CONFIG_MD_RAID456=y -# CONFIG_MD_RAID5_RESHAPE is not set -CONFIG_MD_MULTIPATH=y -# CONFIG_MD_FAULTY is not set -CONFIG_BLK_DEV_DM=y -# CONFIG_DM_DEBUG is not set -CONFIG_DM_CRYPT=m -CONFIG_DM_SNAPSHOT=m -CONFIG_DM_MIRROR=m -CONFIG_DM_ZERO=m -CONFIG_DM_MULTIPATH=m -CONFIG_DM_MULTIPATH_EMC=m -# CONFIG_DM_MULTIPATH_RDAC is not set -# CONFIG_DM_DELAY is not set -CONFIG_FUSION=y -CONFIG_FUSION_SPI=y -CONFIG_FUSION_FC=y -CONFIG_FUSION_SAS=y -CONFIG_FUSION_MAX_SGE=128 -CONFIG_FUSION_CTL=m -CONFIG_FUSION_LOGGING=y - -# -# IEEE 1394 (FireWire) support -# -# CONFIG_FIREWIRE is not set -# CONFIG_IEEE1394 is not set -# CONFIG_I2O is not set -CONFIG_NETDEVICES=y -# CONFIG_NETDEVICES_MULTIQUEUE is not set -# CONFIG_DUMMY is not set -# CONFIG_BONDING is not set -# CONFIG_MACVLAN is not set -# CONFIG_EQUALIZER is not set -# CONFIG_TUN is not set -# CONFIG_VETH is not set -# CONFIG_NET_SB1000 is not set -# CONFIG_IP1000 is not set -# CONFIG_ARCNET is not set -# CONFIG_NET_ETHERNET is not set -CONFIG_NETDEV_1000=y -# CONFIG_ACENIC is not set -# CONFIG_DL2K is not set -# CONFIG_E1000 is not set -# CONFIG_E1000E is not set -# CONFIG_NS83820 is not set -# CONFIG_HAMACHI is not set -# CONFIG_YELLOWFIN is not set -# CONFIG_R8169 is not set -# CONFIG_SIS190 is not set -# CONFIG_SKGE is not set -# CONFIG_SKY2 is not set -# CONFIG_SK98LIN is not set -# CONFIG_VIA_VELOCITY is not set -CONFIG_TIGON3=y -# CONFIG_BNX2 is not set -# CONFIG_QLA3XXX is not set -# CONFIG_ATL1 is not set -CONFIG_NETDEV_10000=y -CONFIG_CHELSIO_T1=m -CONFIG_CHELSIO_T1_1G=y -# CONFIG_CHELSIO_T1_NAPI is not set -CONFIG_CHELSIO_T3=m -CONFIG_IXGBE=m -# CONFIG_IXGB is not set -CONFIG_S2IO=m -# CONFIG_S2IO_NAPI is not set -# CONFIG_MYRI10GE is not set -# CONFIG_NETXEN_NIC is not set -# CONFIG_NIU is not set -# CONFIG_MLX4_CORE is not set -# CONFIG_TEHUTI is not set -# CONFIG_TR is not set - -# -# Wireless LAN -# -# CONFIG_WLAN_PRE80211 is not set -# CONFIG_WLAN_80211 is not set - -# -# USB Network Adapters -# -# CONFIG_USB_CATC is not set -# CONFIG_USB_KAWETH is not set -# CONFIG_USB_PEGASUS is not set -# CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set -# CONFIG_USB_USBNET is not set -# CONFIG_WAN is not set -# CONFIG_FDDI is not set -# CONFIG_HIPPI is not set -# CONFIG_PPP is not set -# CONFIG_SLIP is not set -# CONFIG_NET_FC is not set -# CONFIG_SHAPER is not set -CONFIG_NETCONSOLE=y -# CONFIG_NETCONSOLE_DYNAMIC is not set -CONFIG_NETPOLL=y -# CONFIG_NETPOLL_TRAP is not set -CONFIG_NET_POLL_CONTROLLER=y -# CONFIG_ISDN is not set -# CONFIG_PHONE is not set - -# -# Input device support -# -CONFIG_INPUT=y -# CONFIG_INPUT_FF_MEMLESS is not set -# CONFIG_INPUT_POLLDEV is not set - -# -# Userland interfaces -# -CONFIG_INPUT_MOUSEDEV=y -# CONFIG_INPUT_MOUSEDEV_PSAUX is not set -CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 -CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 -# CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_EVDEV is not set -# CONFIG_INPUT_EVBUG is not set - -# -# Input Device Drivers -# -# CONFIG_INPUT_KEYBOARD is not set -# CONFIG_INPUT_MOUSE is not set -# CONFIG_INPUT_JOYSTICK is not set -# CONFIG_INPUT_TABLET is not set -# CONFIG_INPUT_TOUCHSCREEN is not set -# CONFIG_INPUT_MISC is not set - -# -# Hardware I/O ports -# -# CONFIG_SERIO is not set -# CONFIG_GAMEPORT is not set - -# -# Character devices -# -CONFIG_VT=y -# CONFIG_VT_UNICODE is not set -CONFIG_VT_CONSOLE=y -CONFIG_HW_CONSOLE=y -# CONFIG_VT_HW_CONSOLE_BINDING is not set -CONFIG_SERIAL_NONSTANDARD=y -# CONFIG_COMPUTONE is not set -# CONFIG_ROCKETPORT is not set -# CONFIG_CYCLADES is not set -# CONFIG_DIGIEPCA is not set -# CONFIG_MOXA_INTELLIO is not set -# CONFIG_MOXA_SMARTIO is not set -# CONFIG_MOXA_SMARTIO_NEW is not set -# CONFIG_ISI is not set -# CONFIG_SYNCLINKMP is not set -# CONFIG_SYNCLINK_GT is not set -# CONFIG_N_HDLC is not set -# CONFIG_SPECIALIX is not set -# CONFIG_SX is not set -# CONFIG_RIO is not set -# CONFIG_STALDRV is not set -CONFIG_SGI_SNSC=y -CONFIG_SGI_TIOCX=y -CONFIG_SGI_MBCS=m - -# -# Serial drivers -# -# CONFIG_SERIAL_8250 is not set - -# -# Non-8250 serial port support -# -CONFIG_SERIAL_CORE=y -CONFIG_SERIAL_CORE_CONSOLE=y -CONFIG_SERIAL_SGI_L1_CONSOLE=y -# CONFIG_SERIAL_JSM is not set -CONFIG_SERIAL_SGI_IOC4=y -CONFIG_SERIAL_SGI_IOC3=y -CONFIG_UNIX98_PTYS=y -CONFIG_LEGACY_PTYS=y -CONFIG_LEGACY_PTY_COUNT=256 -# CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set -# CONFIG_HW_RANDOM is not set -CONFIG_EFI_RTC=y -# CONFIG_R3964 is not set -# CONFIG_APPLICOM is not set -CONFIG_RAW_DRIVER=m -CONFIG_MAX_RAW_DEVS=256 -# CONFIG_HPET is not set -# CONFIG_HANGCHECK_TIMER is not set -CONFIG_MMTIMER=y -# CONFIG_TCG_TPM is not set -CONFIG_DEVPORT=y -# CONFIG_I2C is not set - -# -# SPI support -# -# CONFIG_SPI is not set -# CONFIG_SPI_MASTER is not set -# CONFIG_W1 is not set -# CONFIG_POWER_SUPPLY is not set -# CONFIG_HWMON is not set - -# -# Sonics Silicon Backplane -# -CONFIG_SSB_POSSIBLE=y -# CONFIG_SSB is not set - -# -# Multifunction device drivers -# -# CONFIG_MFD_SM501 is not set - -# -# Multimedia devices -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_DAB is not set - -# -# Graphics support -# -CONFIG_AGP=y -CONFIG_AGP_SGI_TIOCA=y -# CONFIG_DRM is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=m -# CONFIG_FB is not set -# CONFIG_BACKLIGHT_LCD_SUPPORT is not set - -# -# Display device support -# -# CONFIG_DISPLAY_SUPPORT is not set - -# -# Console display driver support -# -CONFIG_VGA_CONSOLE=y -# CONFIG_VGACON_SOFT_SCROLLBACK is not set -CONFIG_DUMMY_CONSOLE=y - -# -# Sound -# -# CONFIG_SOUND is not set -CONFIG_HID_SUPPORT=y -CONFIG_HID=y -CONFIG_HID_DEBUG=y -# CONFIG_HIDRAW is not set - -# -# USB Input Devices -# -CONFIG_USB_HID=m -# CONFIG_USB_HIDINPUT_POWERBOOK is not set -# CONFIG_HID_FF is not set -# CONFIG_USB_HIDDEV is not set - -# -# USB HID Boot Protocol drivers -# -# CONFIG_USB_KBD is not set -# CONFIG_USB_MOUSE is not set -CONFIG_USB_SUPPORT=y -CONFIG_USB_ARCH_HAS_HCD=y -CONFIG_USB_ARCH_HAS_OHCI=y -CONFIG_USB_ARCH_HAS_EHCI=y -CONFIG_USB=m -# CONFIG_USB_DEBUG is not set - -# -# Miscellaneous USB options -# -# CONFIG_USB_DEVICEFS is not set -CONFIG_USB_DEVICE_CLASS=y -# CONFIG_USB_DYNAMIC_MINORS is not set -# CONFIG_USB_SUSPEND is not set -# CONFIG_USB_PERSIST is not set -# CONFIG_USB_OTG is not set - -# -# USB Host Controller Drivers -# -CONFIG_USB_EHCI_HCD=m -# CONFIG_USB_EHCI_SPLIT_ISO is not set -# CONFIG_USB_EHCI_ROOT_HUB_TT is not set -# CONFIG_USB_EHCI_TT_NEWSCHED is not set -# CONFIG_USB_ISP116X_HCD is not set -CONFIG_USB_OHCI_HCD=m -# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set -# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set -CONFIG_USB_OHCI_LITTLE_ENDIAN=y -CONFIG_USB_UHCI_HCD=m -# CONFIG_USB_SL811_HCD is not set -# CONFIG_USB_R8A66597_HCD is not set - -# -# USB Device Class drivers -# -# CONFIG_USB_ACM is not set -# CONFIG_USB_PRINTER is not set - -# -# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' -# - -# -# may also be needed; see USB_STORAGE Help for more information -# -# CONFIG_USB_STORAGE is not set -# CONFIG_USB_LIBUSUAL is not set - -# -# USB Imaging devices -# -# CONFIG_USB_MDC800 is not set -# CONFIG_USB_MICROTEK is not set -CONFIG_USB_MON=y - -# -# USB port drivers -# - -# -# USB Serial Converter support -# -# CONFIG_USB_SERIAL is not set - -# -# USB Miscellaneous drivers -# -# CONFIG_USB_EMI62 is not set -# CONFIG_USB_EMI26 is not set -# CONFIG_USB_ADUTUX is not set -# CONFIG_USB_AUERSWALD is not set -# CONFIG_USB_RIO500 is not set -# CONFIG_USB_LEGOTOWER is not set -# CONFIG_USB_LCD is not set -# CONFIG_USB_BERRY_CHARGE is not set -# CONFIG_USB_LED is not set -# CONFIG_USB_CYPRESS_CY7C63 is not set -# CONFIG_USB_CYTHERM is not set -# CONFIG_USB_PHIDGET is not set -# CONFIG_USB_IDMOUSE is not set -# CONFIG_USB_FTDI_ELAN is not set -# CONFIG_USB_APPLEDISPLAY is not set -# CONFIG_USB_SISUSBVGA is not set -# CONFIG_USB_LD is not set -# CONFIG_USB_TRANCEVIBRATOR is not set -# CONFIG_USB_IOWARRIOR is not set - -# -# USB DSL modem support -# - -# -# USB Gadget Support -# -# CONFIG_USB_GADGET is not set -# CONFIG_MMC is not set -# CONFIG_NEW_LEDS is not set -CONFIG_INFINIBAND=m -# CONFIG_INFINIBAND_USER_MAD is not set -CONFIG_INFINIBAND_USER_ACCESS=m -CONFIG_INFINIBAND_USER_MEM=y -CONFIG_INFINIBAND_ADDR_TRANS=y -CONFIG_INFINIBAND_MTHCA=m -CONFIG_INFINIBAND_MTHCA_DEBUG=y -# CONFIG_INFINIBAND_AMSO1100 is not set -# CONFIG_INFINIBAND_CXGB3 is not set -# CONFIG_MLX4_INFINIBAND is not set -CONFIG_INFINIBAND_IPOIB=m -# CONFIG_INFINIBAND_IPOIB_CM is not set -CONFIG_INFINIBAND_IPOIB_DEBUG=y -# CONFIG_INFINIBAND_IPOIB_DEBUG_DATA is not set -CONFIG_INFINIBAND_SRP=m -# CONFIG_INFINIBAND_ISER is not set -# CONFIG_RTC_CLASS is not set - -# -# Userspace I/O -# -# CONFIG_UIO is not set -CONFIG_MSPEC=y - -# -# File systems -# -CONFIG_EXT2_FS=y -CONFIG_EXT2_FS_XATTR=y -CONFIG_EXT2_FS_POSIX_ACL=y -CONFIG_EXT2_FS_SECURITY=y -# CONFIG_EXT2_FS_XIP is not set -CONFIG_EXT3_FS=y -CONFIG_EXT3_FS_XATTR=y -CONFIG_EXT3_FS_POSIX_ACL=y -CONFIG_EXT3_FS_SECURITY=y -# CONFIG_EXT4DEV_FS is not set -CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set -CONFIG_FS_MBCACHE=y -CONFIG_REISERFS_FS=y -# CONFIG_REISERFS_CHECK is not set -# CONFIG_REISERFS_PROC_INFO is not set -CONFIG_REISERFS_FS_XATTR=y -CONFIG_REISERFS_FS_POSIX_ACL=y -CONFIG_REISERFS_FS_SECURITY=y -# CONFIG_JFS_FS is not set -CONFIG_FS_POSIX_ACL=y -CONFIG_XFS_FS=y -CONFIG_XFS_QUOTA=y -# CONFIG_XFS_SECURITY is not set -CONFIG_XFS_POSIX_ACL=y -CONFIG_XFS_RT=y -# CONFIG_GFS2_FS is not set -# CONFIG_OCFS2_FS is not set -# CONFIG_MINIX_FS is not set -# CONFIG_ROMFS_FS is not set -CONFIG_INOTIFY=y -CONFIG_INOTIFY_USER=y -CONFIG_QUOTA=y -CONFIG_QUOTA_NETLINK_INTERFACE=y -CONFIG_PRINT_QUOTA_WARNING=y -# CONFIG_QFMT_V1 is not set -# CONFIG_QFMT_V2 is not set -CONFIG_QUOTACTL=y -CONFIG_DNOTIFY=y -CONFIG_AUTOFS_FS=m -CONFIG_AUTOFS4_FS=m -CONFIG_FUSE_FS=m - -# -# CD-ROM/DVD Filesystems -# -CONFIG_ISO9660_FS=y -CONFIG_JOLIET=y -# CONFIG_ZISOFS is not set -CONFIG_UDF_FS=m -CONFIG_UDF_NLS=y - -# -# DOS/FAT/NT Filesystems -# -CONFIG_FAT_FS=y -# CONFIG_MSDOS_FS is not set -CONFIG_VFAT_FS=y -CONFIG_FAT_DEFAULT_CODEPAGE=437 -CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" -# CONFIG_NTFS_FS is not set - -# -# Pseudo filesystems -# -CONFIG_PROC_FS=y -CONFIG_PROC_KCORE=y -CONFIG_PROC_SYSCTL=y -CONFIG_SYSFS=y -CONFIG_TMPFS=y -# CONFIG_TMPFS_POSIX_ACL is not set -CONFIG_HUGETLBFS=y -CONFIG_HUGETLB_PAGE=y -# CONFIG_CONFIGFS_FS is not set - -# -# Miscellaneous filesystems -# -# CONFIG_ADFS_FS is not set -# CONFIG_AFFS_FS is not set -# CONFIG_HFS_FS is not set -# CONFIG_HFSPLUS_FS is not set -# CONFIG_BEFS_FS is not set -# CONFIG_BFS_FS is not set -# CONFIG_EFS_FS is not set -# CONFIG_CRAMFS is not set -# CONFIG_VXFS_FS is not set -# CONFIG_HPFS_FS is not set -# CONFIG_QNX4FS_FS is not set -# CONFIG_SYSV_FS is not set -# CONFIG_UFS_FS is not set -CONFIG_NETWORK_FILESYSTEMS=y -CONFIG_NFS_FS=m -CONFIG_NFS_V3=y -# CONFIG_NFS_V3_ACL is not set -CONFIG_NFS_V4=y -CONFIG_NFS_DIRECTIO=y -CONFIG_NFSD=m -CONFIG_NFSD_V3=y -# CONFIG_NFSD_V3_ACL is not set -CONFIG_NFSD_V4=y -CONFIG_NFSD_TCP=y -CONFIG_LOCKD=m -CONFIG_LOCKD_V4=y -CONFIG_EXPORTFS=m -CONFIG_NFS_COMMON=y -CONFIG_SUNRPC=m -CONFIG_SUNRPC_GSS=m -CONFIG_SUNRPC_XPRT_RDMA=m -# CONFIG_SUNRPC_BIND34 is not set -CONFIG_RPCSEC_GSS_KRB5=m -# CONFIG_RPCSEC_GSS_SPKM3 is not set -CONFIG_SMB_FS=m -# CONFIG_SMB_NLS_DEFAULT is not set -CONFIG_CIFS=m -# CONFIG_CIFS_STATS is not set -# CONFIG_CIFS_WEAK_PW_HASH is not set -# CONFIG_CIFS_XATTR is not set -# CONFIG_CIFS_DEBUG2 is not set -# CONFIG_CIFS_EXPERIMENTAL is not set -# CONFIG_NCP_FS is not set -# CONFIG_CODA_FS is not set -# CONFIG_AFS_FS is not set - -# -# Partition Types -# -CONFIG_PARTITION_ADVANCED=y -# CONFIG_ACORN_PARTITION is not set -# CONFIG_OSF_PARTITION is not set -# CONFIG_AMIGA_PARTITION is not set -# CONFIG_ATARI_PARTITION is not set -# CONFIG_MAC_PARTITION is not set -CONFIG_MSDOS_PARTITION=y -# CONFIG_BSD_DISKLABEL is not set -# CONFIG_MINIX_SUBPARTITION is not set -# CONFIG_SOLARIS_X86_PARTITION is not set -# CONFIG_UNIXWARE_DISKLABEL is not set -# CONFIG_LDM_PARTITION is not set -CONFIG_SGI_PARTITION=y -# CONFIG_ULTRIX_PARTITION is not set -# CONFIG_SUN_PARTITION is not set -# CONFIG_KARMA_PARTITION is not set -CONFIG_EFI_PARTITION=y -# CONFIG_SYSV68_PARTITION is not set -CONFIG_NLS=y -CONFIG_NLS_DEFAULT="iso8859-1" -CONFIG_NLS_CODEPAGE_437=y -# CONFIG_NLS_CODEPAGE_737 is not set -# CONFIG_NLS_CODEPAGE_775 is not set -# CONFIG_NLS_CODEPAGE_850 is not set -# CONFIG_NLS_CODEPAGE_852 is not set -# CONFIG_NLS_CODEPAGE_855 is not set -# CONFIG_NLS_CODEPAGE_857 is not set -# CONFIG_NLS_CODEPAGE_860 is not set -# CONFIG_NLS_CODEPAGE_861 is not set -# CONFIG_NLS_CODEPAGE_862 is not set -# CONFIG_NLS_CODEPAGE_863 is not set -# CONFIG_NLS_CODEPAGE_864 is not set -# CONFIG_NLS_CODEPAGE_865 is not set -# CONFIG_NLS_CODEPAGE_866 is not set -# CONFIG_NLS_CODEPAGE_869 is not set -# CONFIG_NLS_CODEPAGE_936 is not set -# CONFIG_NLS_CODEPAGE_950 is not set -# CONFIG_NLS_CODEPAGE_932 is not set -# CONFIG_NLS_CODEPAGE_949 is not set -# CONFIG_NLS_CODEPAGE_874 is not set -# CONFIG_NLS_ISO8859_8 is not set -# CONFIG_NLS_CODEPAGE_1250 is not set -# CONFIG_NLS_CODEPAGE_1251 is not set -# CONFIG_NLS_ASCII is not set -CONFIG_NLS_ISO8859_1=y -# CONFIG_NLS_ISO8859_2 is not set -# CONFIG_NLS_ISO8859_3 is not set -# CONFIG_NLS_ISO8859_4 is not set -# CONFIG_NLS_ISO8859_5 is not set -# CONFIG_NLS_ISO8859_6 is not set -# CONFIG_NLS_ISO8859_7 is not set -# CONFIG_NLS_ISO8859_9 is not set -# CONFIG_NLS_ISO8859_13 is not set -# CONFIG_NLS_ISO8859_14 is not set -# CONFIG_NLS_ISO8859_15 is not set -# CONFIG_NLS_KOI8_R is not set -# CONFIG_NLS_KOI8_U is not set -CONFIG_NLS_UTF8=y -# CONFIG_DLM is not set - -# -# Library routines -# -CONFIG_BITREVERSE=y -# CONFIG_CRC_CCITT is not set -CONFIG_CRC16=m -# CONFIG_CRC_ITU_T is not set -CONFIG_CRC32=y -# CONFIG_CRC7 is not set -CONFIG_LIBCRC32C=m -CONFIG_ZLIB_INFLATE=m -CONFIG_ZLIB_DEFLATE=m -CONFIG_GENERIC_ALLOCATOR=y -CONFIG_PLIST=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT=y -CONFIG_HAS_DMA=y -CONFIG_GENERIC_HARDIRQS=y -CONFIG_GENERIC_IRQ_PROBE=y -CONFIG_GENERIC_PENDING_IRQ=y -CONFIG_IRQ_PER_CPU=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set -# CONFIG_KPROBES is not set - -# -# Kernel hacking -# -# CONFIG_PRINTK_TIME is not set -CONFIG_ENABLE_MUST_CHECK=y -CONFIG_MAGIC_SYSRQ=y -# CONFIG_UNUSED_SYMBOLS is not set -# CONFIG_DEBUG_FS is not set -# CONFIG_HEADERS_CHECK is not set -CONFIG_DEBUG_KERNEL=y -# CONFIG_DEBUG_SHIRQ is not set -CONFIG_DETECT_SOFTLOCKUP=y -CONFIG_SCHED_DEBUG=y -# CONFIG_SCHEDSTATS is not set -# CONFIG_TIMER_STATS is not set -# CONFIG_SLUB_DEBUG_ON is not set -# CONFIG_DEBUG_RT_MUTEXES is not set -# CONFIG_RT_MUTEX_TESTER is not set -# CONFIG_DEBUG_SPINLOCK is not set -# CONFIG_DEBUG_MUTEXES is not set -# CONFIG_DEBUG_SPINLOCK_SLEEP is not set -# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set -# CONFIG_DEBUG_KOBJECT is not set -CONFIG_DEBUG_INFO=y -# CONFIG_DEBUG_VM is not set -# CONFIG_DEBUG_LIST is not set -CONFIG_FORCED_INLINING=y -# CONFIG_BOOT_PRINTK_DELAY is not set -# CONFIG_RCU_TORTURE_TEST is not set -# CONFIG_FAULT_INJECTION is not set -CONFIG_IA64_GRANULE_16MB=y -# CONFIG_IA64_GRANULE_64MB is not set -# CONFIG_IA64_PRINT_HAZARDS is not set -# CONFIG_DISABLE_VHPT is not set -# CONFIG_IA64_DEBUG_CMPXCHG is not set -# CONFIG_IA64_DEBUG_IRQ is not set -CONFIG_SYSVIPC_COMPAT=y - -# -# Security options -# -# CONFIG_KEYS is not set -# CONFIG_SECURITY is not set -# CONFIG_SECURITY_FILE_CAPABILITIES is not set -CONFIG_XOR_BLOCKS=y -CONFIG_ASYNC_CORE=y -CONFIG_ASYNC_MEMCPY=y -CONFIG_ASYNC_XOR=y -CONFIG_CRYPTO=y -CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_BLKCIPHER=m -CONFIG_CRYPTO_HASH=y -CONFIG_CRYPTO_MANAGER=y -CONFIG_CRYPTO_HMAC=y -# CONFIG_CRYPTO_XCBC is not set -# CONFIG_CRYPTO_NULL is not set -# CONFIG_CRYPTO_MD4 is not set -CONFIG_CRYPTO_MD5=y -CONFIG_CRYPTO_SHA1=m -# CONFIG_CRYPTO_SHA256 is not set -# CONFIG_CRYPTO_SHA512 is not set -# CONFIG_CRYPTO_WP512 is not set -# CONFIG_CRYPTO_TGR192 is not set -# CONFIG_CRYPTO_GF128MUL is not set -CONFIG_CRYPTO_ECB=m -CONFIG_CRYPTO_CBC=m -CONFIG_CRYPTO_PCBC=m -# CONFIG_CRYPTO_LRW is not set -# CONFIG_CRYPTO_XTS is not set -# CONFIG_CRYPTO_CRYPTD is not set -CONFIG_CRYPTO_DES=m -# CONFIG_CRYPTO_FCRYPT is not set -# CONFIG_CRYPTO_BLOWFISH is not set -# CONFIG_CRYPTO_TWOFISH is not set -# CONFIG_CRYPTO_SERPENT is not set -# CONFIG_CRYPTO_AES is not set -# CONFIG_CRYPTO_CAST5 is not set -# CONFIG_CRYPTO_CAST6 is not set -# CONFIG_CRYPTO_TEA is not set -# CONFIG_CRYPTO_ARC4 is not set -# CONFIG_CRYPTO_KHAZAD is not set -# CONFIG_CRYPTO_ANUBIS is not set -# CONFIG_CRYPTO_SEED is not set -CONFIG_CRYPTO_DEFLATE=m -# CONFIG_CRYPTO_MICHAEL_MIC is not set -CONFIG_CRYPTO_CRC32C=m -# CONFIG_CRYPTO_CAMELLIA is not set -# CONFIG_CRYPTO_TEST is not set -# CONFIG_CRYPTO_AUTHENC is not set -# CONFIG_CRYPTO_HW is not set -- GitLab From 97653f92c004d322ef27edb168a1b5f31142c6dc Mon Sep 17 00:00:00 2001 From: Robin Holt Date: Fri, 15 Aug 2008 09:21:24 -0500 Subject: [PATCH 581/750] [IA64] Shrink shadow_flush_counts to a short array to save 8k of per_cpu area. Making allmodconfig will break the current build. This patch shrinks the per_cpu__shadow_flush_counts from 16k to 8k which frees enough space to allow allmodconfig to successfully complete. Fixes http://bugzilla.kernel.org/show_bug.cgi?id=11338 Signed-off-by: Robin Holt Acked-by: Jack Steiner Signed-off-by: Tony Luck --- arch/ia64/kernel/smp.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/ia64/kernel/smp.c b/arch/ia64/kernel/smp.c index 3676468612b..da8f020d82c 100644 --- a/arch/ia64/kernel/smp.c +++ b/arch/ia64/kernel/smp.c @@ -58,7 +58,7 @@ static struct local_tlb_flush_counts { unsigned int count; } __attribute__((__aligned__(32))) local_tlb_flush_counts[NR_CPUS]; -static DEFINE_PER_CPU(unsigned int, shadow_flush_counts[NR_CPUS]) ____cacheline_aligned; +static DEFINE_PER_CPU(unsigned short, shadow_flush_counts[NR_CPUS]) ____cacheline_aligned; #define IPI_CALL_FUNC 0 #define IPI_CPU_STOP 1 @@ -254,7 +254,7 @@ smp_local_flush_tlb(void) void smp_flush_tlb_cpumask(cpumask_t xcpumask) { - unsigned int *counts = __ia64_per_cpu_var(shadow_flush_counts); + unsigned short *counts = __ia64_per_cpu_var(shadow_flush_counts); cpumask_t cpumask = xcpumask; int mycpu, cpu, flush_mycpu = 0; @@ -262,7 +262,7 @@ smp_flush_tlb_cpumask(cpumask_t xcpumask) mycpu = smp_processor_id(); for_each_cpu_mask(cpu, cpumask) - counts[cpu] = local_tlb_flush_counts[cpu].count; + counts[cpu] = local_tlb_flush_counts[cpu].count & 0xffff; mb(); for_each_cpu_mask(cpu, cpumask) { @@ -276,7 +276,7 @@ smp_flush_tlb_cpumask(cpumask_t xcpumask) smp_local_flush_tlb(); for_each_cpu_mask(cpu, cpumask) - while(counts[cpu] == local_tlb_flush_counts[cpu].count) + while(counts[cpu] == (local_tlb_flush_counts[cpu].count & 0xffff)) udelay(FLUSH_DELAY); preempt_enable(); -- GitLab From 8a20fd52c663b1796e1f01c0fa21d9b24c2936b6 Mon Sep 17 00:00:00 2001 From: "Luck, Tony" Date: Fri, 15 Aug 2008 15:37:48 -0700 Subject: [PATCH 582/750] [IA64] pci_acpi_scan_root cleanup The code walks all the acpi _CRS methods to see how many windows to allocate. It then scans them all again to insert_resource() for each *even if the first scan found that there were none*. Move the second scan inside the "if (windows)" clause. Signed-off-by: Tony Luck --- arch/ia64/pci/pci.c | 21 +++++++++++---------- 1 file changed, 11 insertions(+), 10 deletions(-) diff --git a/arch/ia64/pci/pci.c b/arch/ia64/pci/pci.c index 77b15f80f10..7545037a862 100644 --- a/arch/ia64/pci/pci.c +++ b/arch/ia64/pci/pci.c @@ -324,7 +324,6 @@ pcibios_setup_root_windows(struct pci_bus *bus, struct pci_controller *ctrl) struct pci_bus * __devinit pci_acpi_scan_root(struct acpi_device *device, int domain, int bus) { - struct pci_root_info info; struct pci_controller *controller; unsigned int windows = 0; struct pci_bus *pbus; @@ -346,22 +345,24 @@ pci_acpi_scan_root(struct acpi_device *device, int domain, int bus) acpi_walk_resources(device->handle, METHOD_NAME__CRS, count_window, &windows); if (windows) { + struct pci_root_info info; + controller->window = kmalloc_node(sizeof(*controller->window) * windows, GFP_KERNEL, controller->node); if (!controller->window) goto out2; - } - name = kmalloc(16, GFP_KERNEL); - if (!name) - goto out3; + name = kmalloc(16, GFP_KERNEL); + if (!name) + goto out3; - sprintf(name, "PCI Bus %04x:%02x", domain, bus); - info.controller = controller; - info.name = name; - acpi_walk_resources(device->handle, METHOD_NAME__CRS, add_window, - &info); + sprintf(name, "PCI Bus %04x:%02x", domain, bus); + info.controller = controller; + info.name = name; + acpi_walk_resources(device->handle, METHOD_NAME__CRS, + add_window, &info); + } /* * See arch/x86/pci/acpi.c. * The desired pci bus might already be scanned in a quirk. We -- GitLab From 37c23e7fda6913d133ac12012395e58af1fe24c6 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Sat, 16 Aug 2008 19:50:28 +0200 Subject: [PATCH 583/750] [IA64] use generic compat_old_sys_readdir Switch ia64 to the generic compat_sys_old_readdir which is identical except for slightly better error handling. Also remove sys32_getdents which already isn't wired up to the syscall table anymore in favour of compat_sys_getdents. Signed-off-by: Christoph Hellwig Signed-off-by: Tony Luck --- arch/ia64/ia32/ia32_entry.S | 2 +- arch/ia64/ia32/ia32priv.h | 7 -- arch/ia64/ia32/sys_ia32.c | 132 ------------------------------------ 3 files changed, 1 insertion(+), 140 deletions(-) diff --git a/arch/ia64/ia32/ia32_entry.S b/arch/ia64/ia32/ia32_entry.S index 06efd1f9b80..ff88c48c5d1 100644 --- a/arch/ia64/ia32/ia32_entry.S +++ b/arch/ia64/ia32/ia32_entry.S @@ -262,7 +262,7 @@ ia32_syscall_table: data8 sys_uselib data8 sys_swapon data8 sys_reboot - data8 sys32_readdir + data8 compat_sys_old_readdir data8 sys32_mmap /* 90 */ data8 sys32_munmap data8 sys_truncate diff --git a/arch/ia64/ia32/ia32priv.h b/arch/ia64/ia32/ia32priv.h index c5c872b250d..dd0c53687a9 100644 --- a/arch/ia64/ia32/ia32priv.h +++ b/arch/ia64/ia32/ia32priv.h @@ -276,13 +276,6 @@ typedef struct compat_siginfo { } _sifields; } compat_siginfo_t; -struct old_linux32_dirent { - u32 d_ino; - u32 d_offset; - u16 d_namlen; - char d_name[1]; -}; - /* * IA-32 ELF specific definitions for IA-64. */ diff --git a/arch/ia64/ia32/sys_ia32.c b/arch/ia64/ia32/sys_ia32.c index 465116aecb8..bf196cbb379 100644 --- a/arch/ia64/ia32/sys_ia32.c +++ b/arch/ia64/ia32/sys_ia32.c @@ -1210,138 +1210,6 @@ sys32_settimeofday (struct compat_timeval __user *tv, struct timezone __user *tz return do_sys_settimeofday(tv ? &kts : NULL, tz ? &ktz : NULL); } -struct getdents32_callback { - struct compat_dirent __user *current_dir; - struct compat_dirent __user *previous; - int count; - int error; -}; - -struct readdir32_callback { - struct old_linux32_dirent __user * dirent; - int count; -}; - -static int -filldir32 (void *__buf, const char *name, int namlen, loff_t offset, u64 ino, - unsigned int d_type) -{ - struct compat_dirent __user * dirent; - struct getdents32_callback * buf = (struct getdents32_callback *) __buf; - int reclen = ROUND_UP(offsetof(struct compat_dirent, d_name) + namlen + 1, 4); - u32 d_ino; - - buf->error = -EINVAL; /* only used if we fail.. */ - if (reclen > buf->count) - return -EINVAL; - d_ino = ino; - if (sizeof(d_ino) < sizeof(ino) && d_ino != ino) - return -EOVERFLOW; - buf->error = -EFAULT; /* only used if we fail.. */ - dirent = buf->previous; - if (dirent) - if (put_user(offset, &dirent->d_off)) - return -EFAULT; - dirent = buf->current_dir; - buf->previous = dirent; - if (put_user(d_ino, &dirent->d_ino) - || put_user(reclen, &dirent->d_reclen) - || copy_to_user(dirent->d_name, name, namlen) - || put_user(0, dirent->d_name + namlen)) - return -EFAULT; - dirent = (struct compat_dirent __user *) ((char __user *) dirent + reclen); - buf->current_dir = dirent; - buf->count -= reclen; - return 0; -} - -asmlinkage long -sys32_getdents (unsigned int fd, struct compat_dirent __user *dirent, unsigned int count) -{ - struct file * file; - struct compat_dirent __user * lastdirent; - struct getdents32_callback buf; - int error; - - error = -EFAULT; - if (!access_ok(VERIFY_WRITE, dirent, count)) - goto out; - - error = -EBADF; - file = fget(fd); - if (!file) - goto out; - - buf.current_dir = dirent; - buf.previous = NULL; - buf.count = count; - buf.error = 0; - - error = vfs_readdir(file, filldir32, &buf); - if (error < 0) - goto out_putf; - error = buf.error; - lastdirent = buf.previous; - if (lastdirent) { - if (put_user(file->f_pos, &lastdirent->d_off)) - error = -EFAULT; - else - error = count - buf.count; - } - -out_putf: - fput(file); -out: - return error; -} - -static int -fillonedir32 (void * __buf, const char * name, int namlen, loff_t offset, u64 ino, - unsigned int d_type) -{ - struct readdir32_callback * buf = (struct readdir32_callback *) __buf; - struct old_linux32_dirent __user * dirent; - u32 d_ino; - - if (buf->count) - return -EINVAL; - d_ino = ino; - if (sizeof(d_ino) < sizeof(ino) && d_ino != ino) - return -EOVERFLOW; - buf->count++; - dirent = buf->dirent; - if (put_user(d_ino, &dirent->d_ino) - || put_user(offset, &dirent->d_offset) - || put_user(namlen, &dirent->d_namlen) - || copy_to_user(dirent->d_name, name, namlen) - || put_user(0, dirent->d_name + namlen)) - return -EFAULT; - return 0; -} - -asmlinkage long -sys32_readdir (unsigned int fd, void __user *dirent, unsigned int count) -{ - int error; - struct file * file; - struct readdir32_callback buf; - - error = -EBADF; - file = fget(fd); - if (!file) - goto out; - - buf.count = 0; - buf.dirent = dirent; - - error = vfs_readdir(file, fillonedir32, &buf); - if (error >= 0) - error = buf.count; - fput(file); -out: - return error; -} - struct sel_arg_struct { unsigned int n; unsigned int inp; -- GitLab From 8a7c5ef3ba8cca8f9c4f91ddef3d081f517914ae Mon Sep 17 00:00:00 2001 From: Jiri Kosina Date: Tue, 19 Aug 2008 02:13:55 +0200 Subject: [PATCH 584/750] x86 iommu: remove unneeded parenthesis The parenthesis in __iommu_queue_command() are not needed when assigning into 'target' variable. Signed-off-by: Jiri Kosina Signed-off-by: Ingo Molnar --- arch/x86/kernel/amd_iommu.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c index de39e1f2ede..69b4d060b21 100644 --- a/arch/x86/kernel/amd_iommu.c +++ b/arch/x86/kernel/amd_iommu.c @@ -65,7 +65,7 @@ static int __iommu_queue_command(struct amd_iommu *iommu, struct iommu_cmd *cmd) u8 *target; tail = readl(iommu->mmio_base + MMIO_CMD_TAIL_OFFSET); - target = (iommu->cmd_buf + tail); + target = iommu->cmd_buf + tail; memcpy_toio(target, cmd, sizeof(*cmd)); tail = (tail + sizeof(*cmd)) % iommu->cmd_buf_size; head = readl(iommu->mmio_base + MMIO_CMD_HEAD_OFFSET); -- GitLab From e2fe16d91228a005811335fbc4fbad5d4f5b75af Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Fri, 15 Aug 2008 15:36:31 -0700 Subject: [PATCH 585/750] x86: boot: stub out unimplemented CPU feature words The CPU feature detection code in the boot code is somewhat minimal, and doesn't include all possible CPUID words. In particular, it doesn't contain the code for CPU feature words 2 (Transmeta), 3 (Linux-specific), 5 (VIA), or 7 (scattered). Zero them out, so we can still set those bits as known at compile time; in particular, this allows creating a Linux-specific NOPL flag and have it required (and therefore resolvable at compile time) in 64-bit mode. Signed-off-by: H. Peter Anvin --- arch/x86/boot/cpucheck.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/x86/boot/cpucheck.c b/arch/x86/boot/cpucheck.c index 7804389ee00..19b14f7ef9f 100644 --- a/arch/x86/boot/cpucheck.c +++ b/arch/x86/boot/cpucheck.c @@ -46,12 +46,12 @@ static const u32 req_flags[NCAPINTS] = { REQUIRED_MASK0, REQUIRED_MASK1, - REQUIRED_MASK2, - REQUIRED_MASK3, + 0, /* REQUIRED_MASK2 not implemented in this file */ + 0, /* REQUIRED_MASK3 not implemented in this file */ REQUIRED_MASK4, - REQUIRED_MASK5, + 0, /* REQUIRED_MASK5 not implemented in this file */ REQUIRED_MASK6, - REQUIRED_MASK7, + 0, /* REQUIRED_MASK7 not implemented in this file */ }; #define A32(a, b, c, d) (((d) << 24)+((c) << 16)+((b) << 8)+(a)) -- GitLab From 7e00df5818964298c9821365a6cb7a8304227c5c Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Mon, 18 Aug 2008 17:39:32 -0700 Subject: [PATCH 586/750] x86: add NOPL as a synthetic CPU feature bit The long noops ("NOPL") are supposed to be detected by family >= 6. Unfortunately, several non-Intel x86 implementations, both hardware and software, don't obey this dictum. Instead, probe for NOPL directly by executing a NOPL instruction and see if we get #UD. Signed-off-by: H. Peter Anvin --- arch/x86/kernel/cpu/common.c | 32 ++++++++++++++++++++++++- arch/x86/kernel/cpu/common_64.c | 36 +++++++++++++++++++++++++++++ arch/x86/kernel/cpu/feature_names.c | 3 ++- include/asm-x86/cpufeature.h | 11 +++++---- include/asm-x86/required-features.h | 8 ++++++- 5 files changed, 82 insertions(+), 8 deletions(-) diff --git a/arch/x86/kernel/cpu/common.c b/arch/x86/kernel/cpu/common.c index 80ab20d4fa3..0785b3c8d04 100644 --- a/arch/x86/kernel/cpu/common.c +++ b/arch/x86/kernel/cpu/common.c @@ -13,6 +13,7 @@ #include #include #include +#include #ifdef CONFIG_X86_LOCAL_APIC #include #include @@ -341,6 +342,35 @@ static void __init early_cpu_detect(void) early_get_cap(c); } +/* + * The NOPL instruction is supposed to exist on all CPUs with + * family >= 6, unfortunately, that's not true in practice because + * of early VIA chips and (more importantly) broken virtualizers that + * are not easy to detect. Hence, probe for it based on first + * principles. + */ +static void __cpuinit detect_nopl(struct cpuinfo_x86 *c) +{ + const u32 nopl_signature = 0x888c53b1; /* Random number */ + u32 has_nopl = nopl_signature; + + clear_cpu_cap(c, X86_FEATURE_NOPL); + if (c->x86 >= 6) { + asm volatile("\n" + "1: .byte 0x0f,0x1f,0xc0\n" /* nopl %eax */ + "2:\n" + " .section .fixup,\"ax\"\n" + "3: xor %0,%0\n" + " jmp 2b\n" + " .previous\n" + _ASM_EXTABLE(1b,3b) + : "+a" (has_nopl)); + + if (has_nopl == nopl_signature) + set_cpu_cap(c, X86_FEATURE_NOPL); + } +} + static void __cpuinit generic_identify(struct cpuinfo_x86 *c) { u32 tfms, xlvl; @@ -395,8 +425,8 @@ static void __cpuinit generic_identify(struct cpuinfo_x86 *c) } init_scattered_cpuid_features(c); + detect_nopl(c); } - } static void __cpuinit squash_the_stupid_serial_number(struct cpuinfo_x86 *c) diff --git a/arch/x86/kernel/cpu/common_64.c b/arch/x86/kernel/cpu/common_64.c index dd6e3f15017..c3afba5a81a 100644 --- a/arch/x86/kernel/cpu/common_64.c +++ b/arch/x86/kernel/cpu/common_64.c @@ -18,6 +18,7 @@ #include #include #include +#include #include #ifdef CONFIG_X86_LOCAL_APIC #include @@ -215,6 +216,39 @@ static void __init early_cpu_support_print(void) } } +/* + * The NOPL instruction is supposed to exist on all CPUs with + * family >= 6, unfortunately, that's not true in practice because + * of early VIA chips and (more importantly) broken virtualizers that + * are not easy to detect. Hence, probe for it based on first + * principles. + * + * Note: no 64-bit chip is known to lack these, but put the code here + * for consistency with 32 bits, and to make it utterly trivial to + * diagnose the problem should it ever surface. + */ +static void __cpuinit detect_nopl(struct cpuinfo_x86 *c) +{ + const u32 nopl_signature = 0x888c53b1; /* Random number */ + u32 has_nopl = nopl_signature; + + clear_cpu_cap(c, X86_FEATURE_NOPL); + if (c->x86 >= 6) { + asm volatile("\n" + "1: .byte 0x0f,0x1f,0xc0\n" /* nopl %eax */ + "2:\n" + " .section .fixup,\"ax\"\n" + "3: xor %0,%0\n" + " jmp 2b\n" + " .previous\n" + _ASM_EXTABLE(1b,3b) + : "+a" (has_nopl)); + + if (has_nopl == nopl_signature) + set_cpu_cap(c, X86_FEATURE_NOPL); + } +} + static void __cpuinit early_identify_cpu(struct cpuinfo_x86 *c); void __init early_cpu_init(void) @@ -313,6 +347,8 @@ static void __cpuinit early_identify_cpu(struct cpuinfo_x86 *c) c->x86_phys_bits = eax & 0xff; } + detect_nopl(c); + if (c->x86_vendor != X86_VENDOR_UNKNOWN && cpu_devs[c->x86_vendor]->c_early_init) cpu_devs[c->x86_vendor]->c_early_init(c); diff --git a/arch/x86/kernel/cpu/feature_names.c b/arch/x86/kernel/cpu/feature_names.c index e43ad4ad4cb..c9017799497 100644 --- a/arch/x86/kernel/cpu/feature_names.c +++ b/arch/x86/kernel/cpu/feature_names.c @@ -39,7 +39,8 @@ const char * const x86_cap_flags[NCAPINTS*32] = { NULL, NULL, NULL, NULL, "constant_tsc", "up", NULL, "arch_perfmon", "pebs", "bts", NULL, NULL, - "rep_good", NULL, NULL, NULL, NULL, NULL, NULL, NULL, + "rep_good", NULL, NULL, NULL, + "nopl", NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, /* Intel-defined (#2) */ diff --git a/include/asm-x86/cpufeature.h b/include/asm-x86/cpufeature.h index 2f5a792b0ac..be8b2ad5d41 100644 --- a/include/asm-x86/cpufeature.h +++ b/include/asm-x86/cpufeature.h @@ -72,14 +72,15 @@ #define X86_FEATURE_UP (3*32+ 9) /* smp kernel running on up */ #define X86_FEATURE_FXSAVE_LEAK (3*32+10) /* FXSAVE leaks FOP/FIP/FOP */ #define X86_FEATURE_ARCH_PERFMON (3*32+11) /* Intel Architectural PerfMon */ -#define X86_FEATURE_PEBS (3*32+12) /* Precise-Event Based Sampling */ -#define X86_FEATURE_BTS (3*32+13) /* Branch Trace Store */ -#define X86_FEATURE_SYSCALL32 (3*32+14) /* syscall in ia32 userspace */ -#define X86_FEATURE_SYSENTER32 (3*32+15) /* sysenter in ia32 userspace */ +#define X86_FEATURE_PEBS (3*32+12) /* Precise-Event Based Sampling */ +#define X86_FEATURE_BTS (3*32+13) /* Branch Trace Store */ +#define X86_FEATURE_SYSCALL32 (3*32+14) /* syscall in ia32 userspace */ +#define X86_FEATURE_SYSENTER32 (3*32+15) /* sysenter in ia32 userspace */ #define X86_FEATURE_REP_GOOD (3*32+16) /* rep microcode works well on this CPU */ #define X86_FEATURE_MFENCE_RDTSC (3*32+17) /* Mfence synchronizes RDTSC */ #define X86_FEATURE_LFENCE_RDTSC (3*32+18) /* Lfence synchronizes RDTSC */ -#define X86_FEATURE_11AP (3*32+19) /* Bad local APIC aka 11AP */ +#define X86_FEATURE_11AP (3*32+19) /* Bad local APIC aka 11AP */ +#define X86_FEATURE_NOPL (3*32+20) /* The NOPL (0F 1F) instructions */ /* Intel-defined CPU features, CPUID level 0x00000001 (ecx), word 4 */ #define X86_FEATURE_XMM3 (4*32+ 0) /* Streaming SIMD Extensions-3 */ diff --git a/include/asm-x86/required-features.h b/include/asm-x86/required-features.h index adec887dd7c..5c2ff4bc298 100644 --- a/include/asm-x86/required-features.h +++ b/include/asm-x86/required-features.h @@ -41,6 +41,12 @@ # define NEED_3DNOW 0 #endif +#if defined(CONFIG_X86_P6_NOP) || defined(CONFIG_X86_64) +# define NEED_NOPL (1<<(X86_FEATURE_NOPL & 31)) +#else +# define NEED_NOPL 0 +#endif + #ifdef CONFIG_X86_64 #define NEED_PSE 0 #define NEED_MSR (1<<(X86_FEATURE_MSR & 31)) @@ -67,7 +73,7 @@ #define REQUIRED_MASK1 (NEED_LM|NEED_3DNOW) #define REQUIRED_MASK2 0 -#define REQUIRED_MASK3 0 +#define REQUIRED_MASK3 (NEED_NOPL) #define REQUIRED_MASK4 0 #define REQUIRED_MASK5 0 #define REQUIRED_MASK6 0 -- GitLab From f1c5d30e1d79bbfb60eaf189db862d3cb2bcac92 Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Mon, 18 Aug 2008 17:50:33 -0700 Subject: [PATCH 587/750] x86: use X86_FEATURE_NOPL in alternatives Use X86_FEATURE_NOPL to determine if it is safe to use P6 NOPs in alternatives. Also, replace table and loop with simple if statement. Signed-off-by: H. Peter Anvin --- arch/x86/kernel/alternative.c | 36 +++++++++++++---------------------- 1 file changed, 13 insertions(+), 23 deletions(-) diff --git a/arch/x86/kernel/alternative.c b/arch/x86/kernel/alternative.c index 2763cb37b55..65a0c1b4869 100644 --- a/arch/x86/kernel/alternative.c +++ b/arch/x86/kernel/alternative.c @@ -145,35 +145,25 @@ static const unsigned char *const p6_nops[ASM_NOP_MAX+1] = { extern char __vsyscall_0; const unsigned char *const *find_nop_table(void) { - return boot_cpu_data.x86_vendor != X86_VENDOR_INTEL || - boot_cpu_data.x86 < 6 ? k8_nops : p6_nops; + if (boot_cpu_data.x86_vendor == X86_VENDOR_INTEL && + boot_cpu_has(X86_FEATURE_NOPL)) + return p6_nops; + else + return k8_nops; } #else /* CONFIG_X86_64 */ -static const struct nop { - int cpuid; - const unsigned char *const *noptable; -} noptypes[] = { - { X86_FEATURE_K8, k8_nops }, - { X86_FEATURE_K7, k7_nops }, - { X86_FEATURE_P4, p6_nops }, - { X86_FEATURE_P3, p6_nops }, - { -1, NULL } -}; - const unsigned char *const *find_nop_table(void) { - const unsigned char *const *noptable = intel_nops; - int i; - - for (i = 0; noptypes[i].cpuid >= 0; i++) { - if (boot_cpu_has(noptypes[i].cpuid)) { - noptable = noptypes[i].noptable; - break; - } - } - return noptable; + if (boot_cpu_has(X86_FEATURE_K8)) + return k8_nops; + else if (boot_cpu_has(X86_FEATURE_K7)) + return k7_nops; + else if (boot_cpu_has(X86_FEATURE_NOPL)) + return p6_nops; + else + return intel_nops; } #endif /* CONFIG_X86_64 */ -- GitLab From 8608db031b4d2932d645709e2cfe8fbcd91a7305 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Mon, 18 Aug 2008 20:51:18 -0700 Subject: [PATCH 588/750] pkt_sched: Never schedule non-root qdiscs. Based upon initial discovery and patch by Jarek Poplawski. The qdisc watchdogs can be attached to any qdisc, not just the root, so make sure we schedule the correct one. CBQ has a similar bug. Signed-off-by: David S. Miller --- net/sched/sch_api.c | 2 +- net/sched/sch_cbq.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/net/sched/sch_api.c b/net/sched/sch_api.c index c8dc72e1210..98c00847a3d 100644 --- a/net/sched/sch_api.c +++ b/net/sched/sch_api.c @@ -426,7 +426,7 @@ static enum hrtimer_restart qdisc_watchdog(struct hrtimer *timer) wd->qdisc->flags &= ~TCQ_F_THROTTLED; smp_wmb(); - __netif_schedule(wd->qdisc); + __netif_schedule(qdisc_root(wd->qdisc)); return HRTIMER_NORESTART; } diff --git a/net/sched/sch_cbq.c b/net/sched/sch_cbq.c index 4e261ce62f4..47ef492c4ff 100644 --- a/net/sched/sch_cbq.c +++ b/net/sched/sch_cbq.c @@ -654,7 +654,7 @@ static enum hrtimer_restart cbq_undelay(struct hrtimer *timer) } sch->flags &= ~TCQ_F_THROTTLED; - __netif_schedule(sch); + __netif_schedule(qdisc_root(sch)); return HRTIMER_NORESTART; } -- GitLab From 25bfcd5a78a377ea4c54a3c21e44590e2fc478a6 Mon Sep 17 00:00:00 2001 From: Jarek Poplawski Date: Mon, 18 Aug 2008 20:53:34 -0700 Subject: [PATCH 589/750] pkt_sched: Add lockdep annotation for qdisc locks Qdisc locks are initialized in the same function, qdisc_alloc(), so lockdep can't distinguish tx qdisc lock from rx and reports "possible recursive locking detected" when both these locks are taken eg. while using act_mirred with ifb. This looks like a false positive. Anyway, after this patch these locks will be reported more exactly. Reported-by: Denys Fedoryshchenko Signed-off-by: Jarek Poplawski Signed-off-by: David S. Miller --- net/sched/sch_api.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/net/sched/sch_api.c b/net/sched/sch_api.c index 98c00847a3d..7d7070b1eeb 100644 --- a/net/sched/sch_api.c +++ b/net/sched/sch_api.c @@ -27,6 +27,7 @@ #include #include #include +#include #include #include @@ -707,6 +708,10 @@ static int qdisc_graft(struct net_device *dev, struct Qdisc *parent, return err; } +/* lockdep annotation is needed for ingress; egress gets it only for name */ +static struct lock_class_key qdisc_tx_lock; +static struct lock_class_key qdisc_rx_lock; + /* Allocate and initialize new qdisc. @@ -767,6 +772,7 @@ qdisc_create(struct net_device *dev, struct netdev_queue *dev_queue, if (handle == TC_H_INGRESS) { sch->flags |= TCQ_F_INGRESS; handle = TC_H_MAKE(TC_H_INGRESS, 0); + lockdep_set_class(qdisc_lock(sch), &qdisc_rx_lock); } else { if (handle == 0) { handle = qdisc_alloc_handle(dev); @@ -774,6 +780,7 @@ qdisc_create(struct net_device *dev, struct netdev_queue *dev_queue, if (handle == 0) goto err_out3; } + lockdep_set_class(qdisc_lock(sch), &qdisc_tx_lock); } sch->handle = handle; -- GitLab From 4d8863a29c4755a0461cd31b6865026187d6c43a Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Mon, 18 Aug 2008 21:03:15 -0700 Subject: [PATCH 590/750] pkt_sched: Don't hold qdisc lock over qdisc_destroy(). Based upon reports by Denys Fedoryshchenko, and feedback and help from Jarek Poplawski and Herbert Xu. We always either: 1) Never made an external reference to this qdisc. or 2) Did a dev_deactivate() which purged all asynchronous references. So do not lock the qdisc when we call qdisc_destroy(), it's illegal anyways as when we drop the lock this is free'd memory. Signed-off-by: David S. Miller --- net/sched/sch_api.c | 13 ++----------- net/sched/sch_generic.c | 6 ------ 2 files changed, 2 insertions(+), 17 deletions(-) diff --git a/net/sched/sch_api.c b/net/sched/sch_api.c index 7d7070b1eeb..d91a2338877 100644 --- a/net/sched/sch_api.c +++ b/net/sched/sch_api.c @@ -638,11 +638,8 @@ static void notify_and_destroy(struct sk_buff *skb, struct nlmsghdr *n, u32 clid if (new || old) qdisc_notify(skb, n, clid, old, new); - if (old) { - sch_tree_lock(old); + if (old) qdisc_destroy(old); - sch_tree_unlock(old); - } } /* Graft qdisc "new" to class "classid" of qdisc "parent" or @@ -1092,16 +1089,10 @@ create_n_graft: graft: if (1) { - spinlock_t *root_lock; - err = qdisc_graft(dev, p, skb, n, clid, q, NULL); if (err) { - if (q) { - root_lock = qdisc_root_lock(q); - spin_lock_bh(root_lock); + if (q) qdisc_destroy(q); - spin_unlock_bh(root_lock); - } return err; } } diff --git a/net/sched/sch_generic.c b/net/sched/sch_generic.c index 6f96b7bc080..c3ed4d44fc1 100644 --- a/net/sched/sch_generic.c +++ b/net/sched/sch_generic.c @@ -518,8 +518,6 @@ void qdisc_reset(struct Qdisc *qdisc) } EXPORT_SYMBOL(qdisc_reset); -/* Under qdisc_lock(qdisc) and BH! */ - void qdisc_destroy(struct Qdisc *qdisc) { const struct Qdisc_ops *ops = qdisc->ops; @@ -712,14 +710,10 @@ static void shutdown_scheduler_queue(struct net_device *dev, struct Qdisc *qdisc_default = _qdisc_default; if (qdisc) { - spinlock_t *root_lock = qdisc_lock(qdisc); - dev_queue->qdisc = qdisc_default; dev_queue->qdisc_sleeping = qdisc_default; - spin_lock_bh(root_lock); qdisc_destroy(qdisc); - spin_unlock_bh(root_lock); } } -- GitLab From d28934ad8a4e87203a95de9c376611de8bc2f013 Mon Sep 17 00:00:00 2001 From: Gerrit Renker Date: Mon, 18 Aug 2008 21:14:20 -0700 Subject: [PATCH 591/750] dccp: Fix panic caused by too early termination of retransmission mechanism Thanks is due to Wei Yongjun for the detailed analysis and description of this bug at http://marc.info/?l=dccp&m=121739364909199&w=2 The problem is that invalid packets received by a client in state REQUEST cause the retransmission timer for the DCCP-Request to be reset. This includes freeing the Request-skb ( in dccp_rcv_request_sent_state_process() ). As a consequence, * the arrival of further packets cause a double-free, triggering a panic(), * the connection then may hang, since further retransmissions are blocked. This patch changes the order of statements so that the retransmission timer is reset, and the pending Request freed, only if a valid Response has arrived (or the number of sysctl-retries has been exhausted). Further changes: ---------------- To be on the safe side, replaced __kfree_skb with kfree_skb so that if due to unexpected circumstances the sk_send_head is NULL the WARN_ON is used instead. Signed-off-by: Gerrit Renker Signed-off-by: David S. Miller --- net/dccp/input.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/net/dccp/input.c b/net/dccp/input.c index df2f110df94..803933ab396 100644 --- a/net/dccp/input.c +++ b/net/dccp/input.c @@ -411,12 +411,6 @@ static int dccp_rcv_request_sent_state_process(struct sock *sk, struct dccp_sock *dp = dccp_sk(sk); long tstamp = dccp_timestamp(); - /* Stop the REQUEST timer */ - inet_csk_clear_xmit_timer(sk, ICSK_TIME_RETRANS); - WARN_ON(sk->sk_send_head == NULL); - __kfree_skb(sk->sk_send_head); - sk->sk_send_head = NULL; - if (!between48(DCCP_SKB_CB(skb)->dccpd_ack_seq, dp->dccps_awl, dp->dccps_awh)) { dccp_pr_debug("invalid ackno: S.AWL=%llu, " @@ -441,6 +435,12 @@ static int dccp_rcv_request_sent_state_process(struct sock *sk, DCCP_ACKVEC_STATE_RECEIVED)) goto out_invalid_packet; /* FIXME: change error code */ + /* Stop the REQUEST timer */ + inet_csk_clear_xmit_timer(sk, ICSK_TIME_RETRANS); + WARN_ON(sk->sk_send_head == NULL); + kfree_skb(sk->sk_send_head); + sk->sk_send_head = NULL; + dp->dccps_isr = DCCP_SKB_CB(skb)->dccpd_seq; dccp_update_gsr(sk, dp->dccps_isr); /* -- GitLab From 46faec9858e8943226464dac50e205bf210d9174 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Anders=20Grafstr=C3=B6m?= Date: Mon, 18 Aug 2008 21:29:57 -0700 Subject: [PATCH 592/750] netfilter: ipt_addrtype: Fix matching of inverted destination address type MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This patch fixes matching of inverted destination address type. Signed-off-by: Anders Grafström Signed-off-by: Patrick McHardy Signed-off-by: David S. Miller --- net/ipv4/netfilter/ipt_addrtype.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/ipv4/netfilter/ipt_addrtype.c b/net/ipv4/netfilter/ipt_addrtype.c index 49587a49722..462a22c9787 100644 --- a/net/ipv4/netfilter/ipt_addrtype.c +++ b/net/ipv4/netfilter/ipt_addrtype.c @@ -70,7 +70,7 @@ addrtype_mt_v1(const struct sk_buff *skb, const struct net_device *in, (info->flags & IPT_ADDRTYPE_INVERT_SOURCE); if (ret && info->dest) ret &= match_type(dev, iph->daddr, info->dest) ^ - (info->flags & IPT_ADDRTYPE_INVERT_DEST); + !!(info->flags & IPT_ADDRTYPE_INVERT_DEST); return ret; } -- GitLab From 1575e7ea018fec992b94a12a1a491ce693ae9eac Mon Sep 17 00:00:00 2001 From: Pablo Neira Ayuso Date: Mon, 18 Aug 2008 21:30:55 -0700 Subject: [PATCH 593/750] netfilter: ctnetlink: fix double helper assignation for NAT'ed conntracks If we create a conntrack that has NAT handlings and a helper, the helper is assigned twice. This happens because nf_nat_setup_info() - via nf_conntrack_alter_reply() - sets the helper before ctnetlink, which indeed does not check if the conntrack already has a helper as it thinks that it is a brand new conntrack. The fix moves the helper assignation before the set of the status flags. This avoids a bogus assertion in __nf_ct_ext_add (if netfilter assertions are enabled) which checks that the conntrack must not be confirmed. This problem was introduced in 2.6.23 with the netfilter extension infrastructure. Signed-off-by: Pablo Neira Ayuso Signed-off-by: Patrick McHardy --- net/netfilter/nf_conntrack_netlink.c | 34 ++++++++++++++++------------ 1 file changed, 19 insertions(+), 15 deletions(-) diff --git a/net/netfilter/nf_conntrack_netlink.c b/net/netfilter/nf_conntrack_netlink.c index 105a616c5c7..d1fb2f8555e 100644 --- a/net/netfilter/nf_conntrack_netlink.c +++ b/net/netfilter/nf_conntrack_netlink.c @@ -1136,16 +1136,33 @@ ctnetlink_create_conntrack(struct nlattr *cda[], ct->timeout.expires = jiffies + ct->timeout.expires * HZ; ct->status |= IPS_CONFIRMED; + rcu_read_lock(); + helper = __nf_ct_helper_find(rtuple); + if (helper) { + help = nf_ct_helper_ext_add(ct, GFP_KERNEL); + if (help == NULL) { + rcu_read_unlock(); + err = -ENOMEM; + goto err; + } + /* not in hash table yet so not strictly necessary */ + rcu_assign_pointer(help->helper, helper); + } + if (cda[CTA_STATUS]) { err = ctnetlink_change_status(ct, cda); - if (err < 0) + if (err < 0) { + rcu_read_unlock(); goto err; + } } if (cda[CTA_PROTOINFO]) { err = ctnetlink_change_protoinfo(ct, cda); - if (err < 0) + if (err < 0) { + rcu_read_unlock(); goto err; + } } nf_ct_acct_ext_add(ct, GFP_KERNEL); @@ -1155,19 +1172,6 @@ ctnetlink_create_conntrack(struct nlattr *cda[], ct->mark = ntohl(nla_get_be32(cda[CTA_MARK])); #endif - rcu_read_lock(); - helper = __nf_ct_helper_find(rtuple); - if (helper) { - help = nf_ct_helper_ext_add(ct, GFP_KERNEL); - if (help == NULL) { - rcu_read_unlock(); - err = -ENOMEM; - goto err; - } - /* not in hash table yet so not strictly necessary */ - rcu_assign_pointer(help->helper, helper); - } - /* setup master conntrack: this is a confirmed expectation */ if (master_ct) { __set_bit(IPS_EXPECTED_BIT, &ct->status); -- GitLab From cb1cb5c47457ff2b604dac2da44cab4d39d11459 Mon Sep 17 00:00:00 2001 From: Pablo Neira Ayuso Date: Mon, 18 Aug 2008 21:31:24 -0700 Subject: [PATCH 594/750] netfilter: ctnetlink: fix sleep in read-side lock section Fix allocation with GFP_KERNEL in ctnetlink_create_conntrack() under read-side lock sections. This problem was introduced in 2.6.25. Signed-off-by: Pablo Neira Ayuso Signed-off-by: Patrick McHardy Signed-off-by: David S. Miller --- net/netfilter/nf_conntrack_netlink.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/netfilter/nf_conntrack_netlink.c b/net/netfilter/nf_conntrack_netlink.c index d1fb2f8555e..a5b95ccb3ce 100644 --- a/net/netfilter/nf_conntrack_netlink.c +++ b/net/netfilter/nf_conntrack_netlink.c @@ -1139,7 +1139,7 @@ ctnetlink_create_conntrack(struct nlattr *cda[], rcu_read_lock(); helper = __nf_ct_helper_find(rtuple); if (helper) { - help = nf_ct_helper_ext_add(ct, GFP_KERNEL); + help = nf_ct_helper_ext_add(ct, GFP_ATOMIC); if (help == NULL) { rcu_read_unlock(); err = -ENOMEM; -- GitLab From fab00c5d15091546be681426c60b2ed2c10513bf Mon Sep 17 00:00:00 2001 From: Pablo Neira Ayuso Date: Mon, 18 Aug 2008 21:31:46 -0700 Subject: [PATCH 595/750] netfilter: ctnetlink: sleepable allocation with spin lock bh This patch removes a GFP_KERNEL allocation while holding a spin lock with bottom halves disabled in ctnetlink_change_helper(). This problem was introduced in 2.6.23 with the netfilter extension infrastructure. Signed-off-by: Pablo Neira Ayuso Signed-off-by: Patrick McHardy Signed-off-by: David S. Miller --- net/netfilter/nf_conntrack_netlink.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/netfilter/nf_conntrack_netlink.c b/net/netfilter/nf_conntrack_netlink.c index a5b95ccb3ce..a8752031adc 100644 --- a/net/netfilter/nf_conntrack_netlink.c +++ b/net/netfilter/nf_conntrack_netlink.c @@ -968,7 +968,7 @@ ctnetlink_change_helper(struct nf_conn *ct, struct nlattr *cda[]) /* need to zero data of old helper */ memset(&help->help, 0, sizeof(help->help)); } else { - help = nf_ct_helper_ext_add(ct, GFP_KERNEL); + help = nf_ct_helper_ext_add(ct, GFP_ATOMIC); if (help == NULL) return -ENOMEM; } -- GitLab From 9f593653742d1dd816c4e94c6e5154a57ccba6d1 Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Mon, 18 Aug 2008 21:32:32 -0700 Subject: [PATCH 596/750] nf_nat: use secure_ipv4_port_ephemeral() for NAT port randomization Use incoming network tuple as seed for NAT port randomization. This avoids concerns of leaking net_random() bits, and also gives better port distribution. Don't have NAT server, compile tested only. Signed-off-by: Stephen Hemminger [ added missing EXPORT_SYMBOL_GPL ] Signed-off-by: Patrick McHardy Signed-off-by: David S. Miller --- drivers/char/random.c | 1 + net/ipv4/netfilter/nf_nat_proto_common.c | 8 ++++++-- 2 files changed, 7 insertions(+), 2 deletions(-) diff --git a/drivers/char/random.c b/drivers/char/random.c index e0d0e371909..1838aa3d24f 100644 --- a/drivers/char/random.c +++ b/drivers/char/random.c @@ -1571,6 +1571,7 @@ u32 secure_ipv4_port_ephemeral(__be32 saddr, __be32 daddr, __be16 dport) return half_md4_transform(hash, keyptr->secret); } +EXPORT_SYMBOL_GPL(secure_ipv4_port_ephemeral); #if defined(CONFIG_IPV6) || defined(CONFIG_IPV6_MODULE) u32 secure_ipv6_port_ephemeral(const __be32 *saddr, const __be32 *daddr, diff --git a/net/ipv4/netfilter/nf_nat_proto_common.c b/net/ipv4/netfilter/nf_nat_proto_common.c index 91537f11273..6c4f11f5144 100644 --- a/net/ipv4/netfilter/nf_nat_proto_common.c +++ b/net/ipv4/netfilter/nf_nat_proto_common.c @@ -73,9 +73,13 @@ bool nf_nat_proto_unique_tuple(struct nf_conntrack_tuple *tuple, range_size = ntohs(range->max.all) - min + 1; } - off = *rover; if (range->flags & IP_NAT_RANGE_PROTO_RANDOM) - off = net_random(); + off = secure_ipv4_port_ephemeral(tuple->src.u3.ip, tuple->dst.u3.ip, + maniptype == IP_NAT_MANIP_SRC + ? tuple->dst.u.all + : tuple->src.u.all); + else + off = *rover; for (i = 0; i < range_size; i++, off++) { *portptr = htons(min + off % range_size); -- GitLab From e5befbd9525d92bb074b70192eb2c69aae65fc60 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Ilpo=20J=C3=A4rvinen?= Date: Mon, 18 Aug 2008 22:30:01 -0700 Subject: [PATCH 597/750] pkt_sched: remove bogus block (cleanup) MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit ...Last block local var got just deleted. Signed-off-by: Ilpo Järvinen Signed-off-by: David S. Miller --- net/sched/sch_api.c | 13 ++++++------- 1 file changed, 6 insertions(+), 7 deletions(-) diff --git a/net/sched/sch_api.c b/net/sched/sch_api.c index d91a2338877..9372ec41ce8 100644 --- a/net/sched/sch_api.c +++ b/net/sched/sch_api.c @@ -1088,14 +1088,13 @@ create_n_graft: } graft: - if (1) { - err = qdisc_graft(dev, p, skb, n, clid, q, NULL); - if (err) { - if (q) - qdisc_destroy(q); - return err; - } + err = qdisc_graft(dev, p, skb, n, clid, q, NULL); + if (err) { + if (q) + qdisc_destroy(q); + return err; } + return 0; } -- GitLab From deb3abf15fb92a608fba630da2e8719862731714 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Mon, 18 Aug 2008 22:32:10 -0700 Subject: [PATCH 598/750] Revert "pkt_sched: Protect gen estimators under est_lock." This reverts commit d4766692e72422f3b0f0e9ac6773d92baad07d51. qdisc_destroy() now runs in RTNL fully again, so this change is no longer needed. Signed-off-by: David S. Miller --- net/core/gen_estimator.c | 9 ++++----- 1 file changed, 4 insertions(+), 5 deletions(-) diff --git a/net/core/gen_estimator.c b/net/core/gen_estimator.c index a89f32fa94f..57abe8266be 100644 --- a/net/core/gen_estimator.c +++ b/net/core/gen_estimator.c @@ -99,7 +99,7 @@ struct gen_estimator_head static struct gen_estimator_head elist[EST_MAX_INTERVAL+1]; -/* Protects against NULL dereference and RCU write-side */ +/* Protects against NULL dereference */ static DEFINE_RWLOCK(est_lock); static void est_timer(unsigned long arg) @@ -185,7 +185,6 @@ int gen_new_estimator(struct gnet_stats_basic *bstats, est->last_packets = bstats->packets; est->avpps = rate_est->pps<<10; - write_lock_bh(&est_lock); if (!elist[idx].timer.function) { INIT_LIST_HEAD(&elist[idx].list); setup_timer(&elist[idx].timer, est_timer, idx); @@ -195,7 +194,6 @@ int gen_new_estimator(struct gnet_stats_basic *bstats, mod_timer(&elist[idx].timer, jiffies + ((HZ/4) << idx)); list_add_rcu(&est->list, &elist[idx].list); - write_unlock_bh(&est_lock); return 0; } @@ -214,6 +212,7 @@ static void __gen_kill_estimator(struct rcu_head *head) * Removes the rate estimator specified by &bstats and &rate_est * and deletes the timer. * + * NOTE: Called under rtnl_mutex */ void gen_kill_estimator(struct gnet_stats_basic *bstats, struct gnet_stats_rate_est *rate_est) @@ -227,17 +226,17 @@ void gen_kill_estimator(struct gnet_stats_basic *bstats, if (!elist[idx].timer.function) continue; - write_lock_bh(&est_lock); list_for_each_entry_safe(e, n, &elist[idx].list, list) { if (e->rate_est != rate_est || e->bstats != bstats) continue; + write_lock_bh(&est_lock); e->bstats = NULL; + write_unlock_bh(&est_lock); list_del_rcu(&e->list); call_rcu(&e->e_rcu, __gen_kill_estimator); } - write_unlock_bh(&est_lock); } } -- GitLab From f3b9605d744df537dee10fd06630f35a62b343ec Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Mon, 18 Aug 2008 22:33:05 -0700 Subject: [PATCH 599/750] Revert "pkt_sched: Add BH protection for qdisc_stab_lock." This reverts commit 1cfa26661a85549063e369e2b40275eeaa7b923c. qdisc_destroy() runs fully under RTNL again and not from softint any longer, so this change is no longer needed. Signed-off-by: David S. Miller --- net/sched/sch_api.c | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) diff --git a/net/sched/sch_api.c b/net/sched/sch_api.c index 9372ec41ce8..ef0efeca635 100644 --- a/net/sched/sch_api.c +++ b/net/sched/sch_api.c @@ -332,7 +332,7 @@ static struct qdisc_size_table *qdisc_get_stab(struct nlattr *opt) if (!s || tsize != s->tsize || (!tab && tsize > 0)) return ERR_PTR(-EINVAL); - spin_lock_bh(&qdisc_stab_lock); + spin_lock(&qdisc_stab_lock); list_for_each_entry(stab, &qdisc_stab_list, list) { if (memcmp(&stab->szopts, s, sizeof(*s))) @@ -340,11 +340,11 @@ static struct qdisc_size_table *qdisc_get_stab(struct nlattr *opt) if (tsize > 0 && memcmp(stab->data, tab, tsize * sizeof(u16))) continue; stab->refcnt++; - spin_unlock_bh(&qdisc_stab_lock); + spin_unlock(&qdisc_stab_lock); return stab; } - spin_unlock_bh(&qdisc_stab_lock); + spin_unlock(&qdisc_stab_lock); stab = kmalloc(sizeof(*stab) + tsize * sizeof(u16), GFP_KERNEL); if (!stab) @@ -355,9 +355,9 @@ static struct qdisc_size_table *qdisc_get_stab(struct nlattr *opt) if (tsize > 0) memcpy(stab->data, tab, tsize * sizeof(u16)); - spin_lock_bh(&qdisc_stab_lock); + spin_lock(&qdisc_stab_lock); list_add_tail(&stab->list, &qdisc_stab_list); - spin_unlock_bh(&qdisc_stab_lock); + spin_unlock(&qdisc_stab_lock); return stab; } @@ -367,14 +367,14 @@ void qdisc_put_stab(struct qdisc_size_table *tab) if (!tab) return; - spin_lock_bh(&qdisc_stab_lock); + spin_lock(&qdisc_stab_lock); if (--tab->refcnt == 0) { list_del(&tab->list); kfree(tab); } - spin_unlock_bh(&qdisc_stab_lock); + spin_unlock(&qdisc_stab_lock); } EXPORT_SYMBOL(qdisc_put_stab); -- GitLab From 195648bbc5ae0848e82f771ecf4cd7497054c212 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Tue, 19 Aug 2008 04:00:36 -0700 Subject: [PATCH 600/750] pkt_sched: Prevent livelock in TX queue running. If dev_deactivate() is trying to quiesce the queue, it is theoretically possible for another cpu to livelock trying to process that queue. This happens because dev_deactivate() grabs the queue spinlock as it checks the queue state, whereas net_tx_action() does a trylock and reschedules the qdisc if it hits the lock. This breaks the livelock by adding a check on __QDISC_STATE_DEACTIVATED to net_tx_action() when the trylock fails. Based upon feedback from Herbert Xu and Jarek Poplawski. Signed-off-by: David S. Miller --- net/core/dev.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/net/core/dev.c b/net/core/dev.c index 8d133802372..60c51f76588 100644 --- a/net/core/dev.c +++ b/net/core/dev.c @@ -1990,7 +1990,9 @@ static void net_tx_action(struct softirq_action *h) qdisc_run(q); spin_unlock(root_lock); } else { - __netif_reschedule(q); + if (!test_bit(__QDISC_STATE_DEACTIVATED, + &q->state)) + __netif_reschedule(q); } } } -- GitLab From cb9808d3d0cb0ed97197decadcf0431140b9e231 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Ilpo=20J=C3=A4rvinen?= Date: Tue, 19 Aug 2008 08:48:57 +0300 Subject: [PATCH 601/750] powerpc/spufs: Remove invalid semicolon after if statement MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Signed-off-by: Ilpo Järvinen Signed-off-by: Jeremy Kerr --- arch/powerpc/platforms/cell/spufs/sched.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/powerpc/platforms/cell/spufs/sched.c b/arch/powerpc/platforms/cell/spufs/sched.c index 4b6b0c3a8c9..1c1b627ee84 100644 --- a/arch/powerpc/platforms/cell/spufs/sched.c +++ b/arch/powerpc/platforms/cell/spufs/sched.c @@ -1037,7 +1037,7 @@ void spuctx_switch_state(struct spu_context *ctx, node = spu->node; if (old_state == SPU_UTIL_USER) atomic_dec(&cbe_spu_info[node].busy_spus); - if (new_state == SPU_UTIL_USER); + if (new_state == SPU_UTIL_USER) atomic_inc(&cbe_spu_info[node].busy_spus); } } -- GitLab From c85e2031eb55381a5e2f0f66c2e1d62ecd58eb85 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Tue, 19 Aug 2008 11:28:23 -0400 Subject: [PATCH 602/750] Input: evdev - fix printf() format for sizeof commit f2afa7711f8585ffc088ba538b9a510e0d5dca12 ("Input: paper over a bug in Synaptics X driver") introduced a compiler warning on 64-bit platforms, as sizeof() returns a size_t, not an (unsigned) int: | drivers/input/evdev.c: In function 'handle_eviocgbit': | drivers/input/evdev.c:684: warning: format '%d' expects type 'int', but argument 3 has type 'long unsigned int' Use the proper `z' modifier for size_t, and make the printf() formats for the sizes unsigned while we're at it. Signed-off-by: Geert Uytterhoeven Signed-off-by: Dmitry Torokhov --- drivers/input/evdev.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/input/evdev.c b/drivers/input/evdev.c index a92d8156755..3524bef62be 100644 --- a/drivers/input/evdev.c +++ b/drivers/input/evdev.c @@ -677,8 +677,8 @@ static int handle_eviocgbit(struct input_dev *dev, unsigned int cmd, void __user len = OLD_KEY_MAX; if (printk_timed_ratelimit(&keymax_warn_time, 10 * 1000)) printk(KERN_WARNING - "evdev.c(EVIOCGBIT): Suspicious buffer size %d, " - "limiting output to %d bytes. See " + "evdev.c(EVIOCGBIT): Suspicious buffer size %u, " + "limiting output to %zu bytes. See " "http://userweb.kernel.org/~dtor/eviocgbit-bug.html\n", OLD_KEY_MAX, BITS_TO_LONGS(OLD_KEY_MAX) * sizeof(long)); -- GitLab From d90c1add96a038fc45c7239017ba4f9a9a5ca42b Mon Sep 17 00:00:00 2001 From: Tomasz Chmielewski Date: Tue, 19 Aug 2008 09:54:20 +0100 Subject: [PATCH 603/750] [ARM] 5208/1: fsg-setup.c fixes This patch against 2.6.27-rc3 does the following changes to FSG-3 setup code: 1) Enable RTC on FSG-3 (proper name is needed). This change is needed due to a recent change in i2c. 2) i variable is only used when compiling for big endian. So move its declaration to ARMEB ifdef to silence the warning when compiling for LE. Mailing list link: http://lists.arm.linux.org.uk/lurker/message/20080813.091556.cae2917e.en.html Signed-off-by: Tomasz Chmielewski Signed-off-by: Russell King --- arch/arm/mach-ixp4xx/fsg-setup.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/mach-ixp4xx/fsg-setup.c b/arch/arm/mach-ixp4xx/fsg-setup.c index 0db3a909ae6..501dfdcc39f 100644 --- a/arch/arm/mach-ixp4xx/fsg-setup.c +++ b/arch/arm/mach-ixp4xx/fsg-setup.c @@ -64,7 +64,7 @@ static struct platform_device fsg_i2c_gpio = { static struct i2c_board_info __initdata fsg_i2c_board_info [] = { { - I2C_BOARD_INFO("rtc-isl1208", 0x6f), + I2C_BOARD_INFO("isl1208", 0x6f), }, }; @@ -179,7 +179,6 @@ static void __init fsg_init(void) { DECLARE_MAC_BUF(mac_buf); uint8_t __iomem *f; - int i; ixp4xx_sys_init(); @@ -228,6 +227,7 @@ static void __init fsg_init(void) f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x400000); if (f) { #ifdef __ARMEB__ + int i; for (i = 0; i < 6; i++) { fsg_plat_eth[0].hwaddr[i] = readb(f + 0x3C0422 + i); fsg_plat_eth[1].hwaddr[i] = readb(f + 0x3C043B + i); -- GitLab From 6848408abf1bc18d9a4d5fed3fcca812745ece05 Mon Sep 17 00:00:00 2001 From: Stefan Richter Date: Sat, 16 Aug 2008 13:36:47 +0200 Subject: [PATCH 604/750] ieee1394: regression in 2.6.25: updates should happen before probes Regression since commit 73cf60232ef16e1f8a64defa97214a1722db1e6c, "ieee1394: use class iteration api": The two loops for (1.) driver updates and (2.) driver probes were replaced by a single loop with bogus needs_probe checks. Hence updates and probes were now intermixed, and especially sbp2 updates (reconnects) held up longer than necessary. While we fix it, change the needs_probe flag to bool type for clarity. Tested by Damien Benoist. Signed-off-by: Stefan Richter --- drivers/ieee1394/nodemgr.c | 29 +++++++++++++++-------------- drivers/ieee1394/nodemgr.h | 2 +- 2 files changed, 16 insertions(+), 15 deletions(-) diff --git a/drivers/ieee1394/nodemgr.c b/drivers/ieee1394/nodemgr.c index 994a21e5a0a..2ebd09a8942 100644 --- a/drivers/ieee1394/nodemgr.c +++ b/drivers/ieee1394/nodemgr.c @@ -844,7 +844,7 @@ static struct node_entry *nodemgr_create_node(octlet_t guid, struct csr1212_csr ne->host = host; ne->nodeid = nodeid; ne->generation = generation; - ne->needs_probe = 1; + ne->needs_probe = true; ne->guid = guid; ne->guid_vendor_id = (guid >> 40) & 0xffffff; @@ -1144,7 +1144,7 @@ static void nodemgr_process_root_directory(struct host_info *hi, struct node_ent struct csr1212_keyval *kv, *vendor_name_kv = NULL; u8 last_key_id = 0; - ne->needs_probe = 0; + ne->needs_probe = false; csr1212_for_each_dir_entry(ne->csr, kv, ne->csr->root_kv, dentry) { switch (kv->key.id) { @@ -1295,7 +1295,7 @@ static void nodemgr_update_node(struct node_entry *ne, struct csr1212_csr *csr, nodemgr_update_bus_options(ne); /* Mark the node as new, so it gets re-probed */ - ne->needs_probe = 1; + ne->needs_probe = true; } else { /* old cache is valid, so update its generation */ struct nodemgr_csr_info *ci = ne->csr->private; @@ -1566,28 +1566,27 @@ static void nodemgr_probe_ne(struct host_info *hi, struct node_entry *ne, int ge struct probe_param { struct host_info *hi; int generation; + bool probe_now; }; -static int __nodemgr_node_probe(struct device *dev, void *data) +static int node_probe(struct device *dev, void *data) { - struct probe_param *param = (struct probe_param *)data; + struct probe_param *p = data; struct node_entry *ne; ne = container_of(dev, struct node_entry, node_dev); - if (!ne->needs_probe) - nodemgr_probe_ne(param->hi, ne, param->generation); - if (ne->needs_probe) - nodemgr_probe_ne(param->hi, ne, param->generation); + if (ne->needs_probe == p->probe_now) + nodemgr_probe_ne(p->hi, ne, p->generation); return 0; } static void nodemgr_node_probe(struct host_info *hi, int generation) { struct hpsb_host *host = hi->host; - struct probe_param param; + struct probe_param p; - param.hi = hi; - param.generation = generation; + p.hi = hi; + p.generation = generation; /* Do some processing of the nodes we've probed. This pulls them * into the sysfs layer if needed, and can result in processing of * unit-directories, or just updating the node and it's @@ -1597,8 +1596,10 @@ static void nodemgr_node_probe(struct host_info *hi, int generation) * while probes are time-consuming. (Well, those probes need some * improvement...) */ - class_for_each_device(&nodemgr_ne_class, NULL, ¶m, - __nodemgr_node_probe); + p.probe_now = false; + class_for_each_device(&nodemgr_ne_class, NULL, &p, node_probe); + p.probe_now = true; + class_for_each_device(&nodemgr_ne_class, NULL, &p, node_probe); /* If we had a bus reset while we were scanning the bus, it is * possible that we did not probe all nodes. In that case, we diff --git a/drivers/ieee1394/nodemgr.h b/drivers/ieee1394/nodemgr.h index 919e92e2a95..6eb26465a84 100644 --- a/drivers/ieee1394/nodemgr.h +++ b/drivers/ieee1394/nodemgr.h @@ -97,7 +97,7 @@ struct node_entry { struct hpsb_host *host; /* Host this node is attached to */ nodeid_t nodeid; /* NodeID */ struct bus_options busopt; /* Bus Options */ - int needs_probe; + bool needs_probe; unsigned int generation; /* Synced with hpsb generation */ /* The following is read from the config rom */ -- GitLab From c921a9745705ed62a949192ef9128c60d6c63874 Mon Sep 17 00:00:00 2001 From: Stefan Richter Date: Sat, 16 Aug 2008 13:38:11 +0200 Subject: [PATCH 605/750] ieee1394: don't drop nodes during bus reset series nodemgr_node_probe checked for generation increments too late and therefore prematurely reported nodes as "suspended". Fixes http://bugzilla.kernel.org/show_bug.cgi?id=11349. Reported and tested by Damien Benoist. Signed-off-by: Stefan Richter --- drivers/ieee1394/nodemgr.c | 40 ++++++++++++++++++++------------------ 1 file changed, 21 insertions(+), 19 deletions(-) diff --git a/drivers/ieee1394/nodemgr.c b/drivers/ieee1394/nodemgr.c index 2ebd09a8942..16240a78965 100644 --- a/drivers/ieee1394/nodemgr.c +++ b/drivers/ieee1394/nodemgr.c @@ -1574,6 +1574,9 @@ static int node_probe(struct device *dev, void *data) struct probe_param *p = data; struct node_entry *ne; + if (p->generation != get_hpsb_generation(p->hi->host)) + return -EAGAIN; + ne = container_of(dev, struct node_entry, node_dev); if (ne->needs_probe == p->probe_now) nodemgr_probe_ne(p->hi, ne, p->generation); @@ -1582,42 +1585,41 @@ static int node_probe(struct device *dev, void *data) static void nodemgr_node_probe(struct host_info *hi, int generation) { - struct hpsb_host *host = hi->host; struct probe_param p; p.hi = hi; p.generation = generation; - /* Do some processing of the nodes we've probed. This pulls them + /* + * Do some processing of the nodes we've probed. This pulls them * into the sysfs layer if needed, and can result in processing of * unit-directories, or just updating the node and it's * unit-directories. * * Run updates before probes. Usually, updates are time-critical - * while probes are time-consuming. (Well, those probes need some - * improvement...) */ - + * while probes are time-consuming. + * + * Meanwhile, another bus reset may have happened. In this case we + * skip everything here and let the next bus scan handle it. + * Otherwise we may prematurely remove nodes which are still there. + */ p.probe_now = false; - class_for_each_device(&nodemgr_ne_class, NULL, &p, node_probe); - p.probe_now = true; - class_for_each_device(&nodemgr_ne_class, NULL, &p, node_probe); + if (class_for_each_device(&nodemgr_ne_class, NULL, &p, node_probe) != 0) + return; - /* If we had a bus reset while we were scanning the bus, it is - * possible that we did not probe all nodes. In that case, we - * skip the clean up for now, since we could remove nodes that - * were still on the bus. Another bus scan is pending which will - * do the clean up eventually. - * + p.probe_now = true; + if (class_for_each_device(&nodemgr_ne_class, NULL, &p, node_probe) != 0) + return; + /* * Now let's tell the bus to rescan our devices. This may seem * like overhead, but the driver-model core will only scan a * device for a driver when either the device is added, or when a * new driver is added. A bus reset is a good reason to rescan * devices that were there before. For example, an sbp2 device * may become available for login, if the host that held it was - * just removed. */ - - if (generation == get_hpsb_generation(host)) - if (bus_rescan_devices(&ieee1394_bus_type)) - HPSB_DEBUG("bus_rescan_devices had an error"); + * just removed. + */ + if (bus_rescan_devices(&ieee1394_bus_type) != 0) + HPSB_DEBUG("bus_rescan_devices had an error"); } static int nodemgr_send_resume_packet(struct hpsb_host *host) -- GitLab From a3384067fb0df9c58e112ac6a5ec9beb7d169482 Mon Sep 17 00:00:00 2001 From: Stefan Richter Date: Sat, 16 Aug 2008 13:39:26 +0200 Subject: [PATCH 606/750] ieee1394: sbp2: let nodemgr retry node updates during bus reset series sbp2 was too quick to report .update() to the ieee1394 core as failed. (Logged as "Failed to reconnect to sbp2 device!".) The core would then unbind sbp2 from the device. This is not justified if the .update() failed because another bus reset happened. We check this and tell the ieee1394 that .update() succeeded, and the core will call sbp2's .update() for the new bus reset as well. This improves reconnection/re-login especially on buses with several disks as they may issue bus resets in close succession when they come online. Tested by Damien Benoist. Signed-off-by: Stefan Richter --- drivers/ieee1394/sbp2.c | 25 ++++++++++++++++++------- 1 file changed, 18 insertions(+), 7 deletions(-) diff --git a/drivers/ieee1394/sbp2.c b/drivers/ieee1394/sbp2.c index 9cbf3154d24..1d6ad343553 100644 --- a/drivers/ieee1394/sbp2.c +++ b/drivers/ieee1394/sbp2.c @@ -731,15 +731,26 @@ static int sbp2_update(struct unit_directory *ud) { struct sbp2_lu *lu = ud->device.driver_data; - if (sbp2_reconnect_device(lu)) { - /* Reconnect has failed. Perhaps we didn't reconnect fast - * enough. Try a regular login, but first log out just in - * case of any weirdness. */ + if (sbp2_reconnect_device(lu) != 0) { + /* + * Reconnect failed. If another bus reset happened, + * let nodemgr proceed and call sbp2_update again later + * (or sbp2_remove if this node went away). + */ + if (!hpsb_node_entry_valid(lu->ne)) + return 0; + /* + * Or the target rejected the reconnect because we weren't + * fast enough. Try a regular login, but first log out + * just in case of any weirdness. + */ sbp2_logout_device(lu); - if (sbp2_login_device(lu)) { - /* Login failed too, just fail, and the backend - * will call our sbp2_remove for us */ + if (sbp2_login_device(lu) != 0) { + if (!hpsb_node_entry_valid(lu->ne)) + return 0; + + /* Maybe another initiator won the login. */ SBP2_ERR("Failed to reconnect to sbp2 device!"); return -EBUSY; } -- GitLab From 30b0aa7c9a5e769a874a456cd56396eebf164b91 Mon Sep 17 00:00:00 2001 From: Stefan Richter Date: Sat, 16 Aug 2008 21:52:28 +0200 Subject: [PATCH 607/750] firewire: Kconfig help update Signed-off-by: Stefan Richter --- drivers/firewire/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/firewire/Kconfig b/drivers/firewire/Kconfig index fa6d6abefd4..45090243820 100644 --- a/drivers/firewire/Kconfig +++ b/drivers/firewire/Kconfig @@ -12,8 +12,8 @@ config FIREWIRE This is the "Juju" FireWire stack, a new alternative implementation designed for robustness and simplicity. You can build either this stack, or the old stack (the ieee1394 driver, ohci1394 etc.) or both. - Please read http://wiki.linux1394.org/JujuMigration before you - enable the new stack. + Please read http://ieee1394.wiki.kernel.org/index.php/Juju_Migration + before you enable the new stack. To compile this driver as a module, say M here: the module will be called firewire-core. -- GitLab From f607e3a03c90e8c050cb0c12ec9967c2925cc812 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Tue, 19 Aug 2008 13:34:59 -0700 Subject: [PATCH 608/750] Revert "[CPUFREQ][2/2] preregister support for powernow-k8" This reverts commit 34ae7f35a21694aa5cb8829dc5142c39d73d6ba0, which has been reported to cause a number of problems. During suspend and resume, it apparently causes a crash in a CPU hotplug notifier to happen, although the exact details are sketchy because of the inability to get good traces during the suspend sequence. See buzilla entries http://bugzilla.kernel.org/show_bug.cgi?id=11296 http://bugzilla.kernel.org/show_bug.cgi?id=11339 for more examples and details. [ Mark: "Revert the patch for now. I'm still looking into getting a reliable reproduction and I do not have a fix at this time." ] Requested-by: Rafael J. Wysocki Acked-by: Mark Langsdorf Acked-by: Dave Jones Signed-off-by: Linus Torvalds --- arch/x86/kernel/cpu/cpufreq/powernow-k8.c | 109 +++++++--------------- arch/x86/kernel/cpu/cpufreq/powernow-k8.h | 3 +- 2 files changed, 37 insertions(+), 75 deletions(-) diff --git a/arch/x86/kernel/cpu/cpufreq/powernow-k8.c b/arch/x86/kernel/cpu/cpufreq/powernow-k8.c index 4e7271999a7..84bb395038d 100644 --- a/arch/x86/kernel/cpu/cpufreq/powernow-k8.c +++ b/arch/x86/kernel/cpu/cpufreq/powernow-k8.c @@ -737,63 +737,44 @@ static int find_psb_table(struct powernow_k8_data *data) #ifdef CONFIG_X86_POWERNOW_K8_ACPI static void powernow_k8_acpi_pst_values(struct powernow_k8_data *data, unsigned int index) { - if (!data->acpi_data->state_count || (cpu_family == CPU_HW_PSTATE)) + if (!data->acpi_data.state_count || (cpu_family == CPU_HW_PSTATE)) return; - data->irt = (data->acpi_data->states[index].control >> IRT_SHIFT) & IRT_MASK; - data->rvo = (data->acpi_data->states[index].control >> RVO_SHIFT) & RVO_MASK; - data->exttype = (data->acpi_data->states[index].control >> EXT_TYPE_SHIFT) & EXT_TYPE_MASK; - data->plllock = (data->acpi_data->states[index].control >> PLL_L_SHIFT) & PLL_L_MASK; - data->vidmvs = 1 << ((data->acpi_data->states[index].control >> MVS_SHIFT) & MVS_MASK); - data->vstable = (data->acpi_data->states[index].control >> VST_SHIFT) & VST_MASK; -} - - -static struct acpi_processor_performance *acpi_perf_data; -static int preregister_valid; - -static int powernow_k8_cpu_preinit_acpi(void) -{ - acpi_perf_data = alloc_percpu(struct acpi_processor_performance); - if (!acpi_perf_data) - return -ENODEV; - - if (acpi_processor_preregister_performance(acpi_perf_data)) - return -ENODEV; - else - preregister_valid = 1; - return 0; + data->irt = (data->acpi_data.states[index].control >> IRT_SHIFT) & IRT_MASK; + data->rvo = (data->acpi_data.states[index].control >> RVO_SHIFT) & RVO_MASK; + data->exttype = (data->acpi_data.states[index].control >> EXT_TYPE_SHIFT) & EXT_TYPE_MASK; + data->plllock = (data->acpi_data.states[index].control >> PLL_L_SHIFT) & PLL_L_MASK; + data->vidmvs = 1 << ((data->acpi_data.states[index].control >> MVS_SHIFT) & MVS_MASK); + data->vstable = (data->acpi_data.states[index].control >> VST_SHIFT) & VST_MASK; } static int powernow_k8_cpu_init_acpi(struct powernow_k8_data *data) { struct cpufreq_frequency_table *powernow_table; int ret_val; - int cpu = 0; - data->acpi_data = percpu_ptr(acpi_perf_data, cpu); - if (acpi_processor_register_performance(data->acpi_data, data->cpu)) { + if (acpi_processor_register_performance(&data->acpi_data, data->cpu)) { dprintk("register performance failed: bad ACPI data\n"); return -EIO; } /* verify the data contained in the ACPI structures */ - if (data->acpi_data->state_count <= 1) { + if (data->acpi_data.state_count <= 1) { dprintk("No ACPI P-States\n"); goto err_out; } - if ((data->acpi_data->control_register.space_id != ACPI_ADR_SPACE_FIXED_HARDWARE) || - (data->acpi_data->status_register.space_id != ACPI_ADR_SPACE_FIXED_HARDWARE)) { + if ((data->acpi_data.control_register.space_id != ACPI_ADR_SPACE_FIXED_HARDWARE) || + (data->acpi_data.status_register.space_id != ACPI_ADR_SPACE_FIXED_HARDWARE)) { dprintk("Invalid control/status registers (%x - %x)\n", - data->acpi_data->control_register.space_id, - data->acpi_data->status_register.space_id); + data->acpi_data.control_register.space_id, + data->acpi_data.status_register.space_id); goto err_out; } /* fill in data->powernow_table */ powernow_table = kmalloc((sizeof(struct cpufreq_frequency_table) - * (data->acpi_data->state_count + 1)), GFP_KERNEL); + * (data->acpi_data.state_count + 1)), GFP_KERNEL); if (!powernow_table) { dprintk("powernow_table memory alloc failure\n"); goto err_out; @@ -806,12 +787,12 @@ static int powernow_k8_cpu_init_acpi(struct powernow_k8_data *data) if (ret_val) goto err_out_mem; - powernow_table[data->acpi_data->state_count].frequency = CPUFREQ_TABLE_END; - powernow_table[data->acpi_data->state_count].index = 0; + powernow_table[data->acpi_data.state_count].frequency = CPUFREQ_TABLE_END; + powernow_table[data->acpi_data.state_count].index = 0; data->powernow_table = powernow_table; /* fill in data */ - data->numps = data->acpi_data->state_count; + data->numps = data->acpi_data.state_count; if (first_cpu(per_cpu(cpu_core_map, data->cpu)) == data->cpu) print_basics(data); powernow_k8_acpi_pst_values(data, 0); @@ -819,31 +800,16 @@ static int powernow_k8_cpu_init_acpi(struct powernow_k8_data *data) /* notify BIOS that we exist */ acpi_processor_notify_smm(THIS_MODULE); - /* determine affinity, from ACPI if available */ - if (preregister_valid) { - if ((data->acpi_data->shared_type == CPUFREQ_SHARED_TYPE_ALL) || - (data->acpi_data->shared_type == CPUFREQ_SHARED_TYPE_ANY)) - data->starting_core_affinity = data->acpi_data->shared_cpu_map; - else - data->starting_core_affinity = cpumask_of_cpu(data->cpu); - } else { - /* best guess from family if not */ - if (cpu_family == CPU_HW_PSTATE) - data->starting_core_affinity = cpumask_of_cpu(data->cpu); - else - data->starting_core_affinity = per_cpu(cpu_core_map, data->cpu); - } - return 0; err_out_mem: kfree(powernow_table); err_out: - acpi_processor_unregister_performance(data->acpi_data, data->cpu); + acpi_processor_unregister_performance(&data->acpi_data, data->cpu); /* data->acpi_data.state_count informs us at ->exit() whether ACPI was used */ - data->acpi_data->state_count = 0; + data->acpi_data.state_count = 0; return -ENODEV; } @@ -855,10 +821,10 @@ static int fill_powernow_table_pstate(struct powernow_k8_data *data, struct cpuf rdmsr(MSR_PSTATE_CUR_LIMIT, hi, lo); data->max_hw_pstate = (hi & HW_PSTATE_MAX_MASK) >> HW_PSTATE_MAX_SHIFT; - for (i = 0; i < data->acpi_data->state_count; i++) { + for (i = 0; i < data->acpi_data.state_count; i++) { u32 index; - index = data->acpi_data->states[i].control & HW_PSTATE_MASK; + index = data->acpi_data.states[i].control & HW_PSTATE_MASK; if (index > data->max_hw_pstate) { printk(KERN_ERR PFX "invalid pstate %d - bad value %d.\n", i, index); printk(KERN_ERR PFX "Please report to BIOS manufacturer\n"); @@ -874,7 +840,7 @@ static int fill_powernow_table_pstate(struct powernow_k8_data *data, struct cpuf powernow_table[i].index = index; - powernow_table[i].frequency = data->acpi_data->states[i].core_frequency * 1000; + powernow_table[i].frequency = data->acpi_data.states[i].core_frequency * 1000; } return 0; } @@ -883,16 +849,16 @@ static int fill_powernow_table_fidvid(struct powernow_k8_data *data, struct cpuf { int i; int cntlofreq = 0; - for (i = 0; i < data->acpi_data->state_count; i++) { + for (i = 0; i < data->acpi_data.state_count; i++) { u32 fid; u32 vid; if (data->exttype) { - fid = data->acpi_data->states[i].status & EXT_FID_MASK; - vid = (data->acpi_data->states[i].status >> VID_SHIFT) & EXT_VID_MASK; + fid = data->acpi_data.states[i].status & EXT_FID_MASK; + vid = (data->acpi_data.states[i].status >> VID_SHIFT) & EXT_VID_MASK; } else { - fid = data->acpi_data->states[i].control & FID_MASK; - vid = (data->acpi_data->states[i].control >> VID_SHIFT) & VID_MASK; + fid = data->acpi_data.states[i].control & FID_MASK; + vid = (data->acpi_data.states[i].control >> VID_SHIFT) & VID_MASK; } dprintk(" %d : fid 0x%x, vid 0x%x\n", i, fid, vid); @@ -933,10 +899,10 @@ static int fill_powernow_table_fidvid(struct powernow_k8_data *data, struct cpuf cntlofreq = i; } - if (powernow_table[i].frequency != (data->acpi_data->states[i].core_frequency * 1000)) { + if (powernow_table[i].frequency != (data->acpi_data.states[i].core_frequency * 1000)) { printk(KERN_INFO PFX "invalid freq entries %u kHz vs. %u kHz\n", powernow_table[i].frequency, - (unsigned int) (data->acpi_data->states[i].core_frequency * 1000)); + (unsigned int) (data->acpi_data.states[i].core_frequency * 1000)); powernow_table[i].frequency = CPUFREQ_ENTRY_INVALID; continue; } @@ -946,12 +912,11 @@ static int fill_powernow_table_fidvid(struct powernow_k8_data *data, struct cpuf static void powernow_k8_cpu_exit_acpi(struct powernow_k8_data *data) { - if (data->acpi_data->state_count) - acpi_processor_unregister_performance(data->acpi_data, data->cpu); + if (data->acpi_data.state_count) + acpi_processor_unregister_performance(&data->acpi_data, data->cpu); } #else -static int powernow_k8_cpu_preinit_acpi(void) { return -ENODEV; } static int powernow_k8_cpu_init_acpi(struct powernow_k8_data *data) { return -ENODEV; } static void powernow_k8_cpu_exit_acpi(struct powernow_k8_data *data) { return; } static void powernow_k8_acpi_pst_values(struct powernow_k8_data *data, unsigned int index) { return; } @@ -1136,7 +1101,7 @@ static int powernowk8_verify(struct cpufreq_policy *pol) static int __cpuinit powernowk8_cpu_init(struct cpufreq_policy *pol) { struct powernow_k8_data *data; - cpumask_t oldmask = CPU_MASK_ALL; + cpumask_t oldmask; int rc; if (!cpu_online(pol->cpu)) @@ -1209,7 +1174,10 @@ static int __cpuinit powernowk8_cpu_init(struct cpufreq_policy *pol) /* run on any CPU again */ set_cpus_allowed_ptr(current, &oldmask); - pol->cpus = data->starting_core_affinity; + if (cpu_family == CPU_HW_PSTATE) + pol->cpus = cpumask_of_cpu(pol->cpu); + else + pol->cpus = per_cpu(cpu_core_map, pol->cpu); data->available_cores = &(pol->cpus); /* Take a crude guess here. @@ -1332,7 +1300,6 @@ static int __cpuinit powernowk8_init(void) } if (supported_cpus == num_online_cpus()) { - powernow_k8_cpu_preinit_acpi(); printk(KERN_INFO PFX "Found %d %s " "processors (%d cpu cores) (" VERSION ")\n", num_online_nodes(), @@ -1349,10 +1316,6 @@ static void __exit powernowk8_exit(void) dprintk("exit\n"); cpufreq_unregister_driver(&cpufreq_amd64_driver); - -#ifdef CONFIG_X86_POWERNOW_K8_ACPI - free_percpu(acpi_perf_data); -#endif } MODULE_AUTHOR("Paul Devriendt and Mark Langsdorf "); diff --git a/arch/x86/kernel/cpu/cpufreq/powernow-k8.h b/arch/x86/kernel/cpu/cpufreq/powernow-k8.h index a62612cd4be..ab48cfed4d9 100644 --- a/arch/x86/kernel/cpu/cpufreq/powernow-k8.h +++ b/arch/x86/kernel/cpu/cpufreq/powernow-k8.h @@ -33,13 +33,12 @@ struct powernow_k8_data { #ifdef CONFIG_X86_POWERNOW_K8_ACPI /* the acpi table needs to be kept. it's only available if ACPI was * used to determine valid frequency/vid/fid states */ - struct acpi_processor_performance *acpi_data; + struct acpi_processor_performance acpi_data; #endif /* we need to keep track of associated cores, but let cpufreq * handle hotplug events - so just point at cpufreq pol->cpus * structure */ cpumask_t *available_cores; - cpumask_t starting_core_affinity; }; -- GitLab From a77a57a1a22afc31891d95879fe3cf2ab03838b0 Mon Sep 17 00:00:00 2001 From: Roland Dreier Date: Tue, 19 Aug 2008 15:01:32 -0700 Subject: [PATCH 609/750] IPoIB: Fix deadlock on RTNL in ipoib_stop() Commit c8c2afe3 ("IPoIB: Use rtnl lock/unlock when changing device flags") added a call to rtnl_lock() in ipoib_mcast_join_task(), which is run from the ipoib_workqueue. However, ipoib_stop() (which is run inside rtnl_lock()) flushes this workqueue, which leads to a deadlock if the join task is pending. Fix this by simply not flushing the workqueue from ipoib_stop(). It turns out that we really don't care about workqueue tasks running during or after ipoib_stop(), as long as we make sure to flush the workqueue before unregistering a netdev. This fixes . Signed-off-by: Roland Dreier --- drivers/infiniband/ulp/ipoib/ipoib_main.c | 19 +++++++++---------- .../infiniband/ulp/ipoib/ipoib_multicast.c | 10 +++++++++- 2 files changed, 18 insertions(+), 11 deletions(-) diff --git a/drivers/infiniband/ulp/ipoib/ipoib_main.c b/drivers/infiniband/ulp/ipoib/ipoib_main.c index f51201b17bf..7e9e218738f 100644 --- a/drivers/infiniband/ulp/ipoib/ipoib_main.c +++ b/drivers/infiniband/ulp/ipoib/ipoib_main.c @@ -156,14 +156,8 @@ static int ipoib_stop(struct net_device *dev) netif_stop_queue(dev); - /* - * Now flush workqueue to make sure a scheduled task doesn't - * bring our internal state back up. - */ - flush_workqueue(ipoib_workqueue); - - ipoib_ib_dev_down(dev, 1); - ipoib_ib_dev_stop(dev, 1); + ipoib_ib_dev_down(dev, 0); + ipoib_ib_dev_stop(dev, 0); if (!test_bit(IPOIB_FLAG_SUBINTERFACE, &priv->flags)) { struct ipoib_dev_priv *cpriv; @@ -1314,7 +1308,7 @@ sysfs_failed: register_failed: ib_unregister_event_handler(&priv->event_handler); - flush_scheduled_work(); + flush_workqueue(ipoib_workqueue); event_failed: ipoib_dev_cleanup(priv->dev); @@ -1373,7 +1367,12 @@ static void ipoib_remove_one(struct ib_device *device) list_for_each_entry_safe(priv, tmp, dev_list, list) { ib_unregister_event_handler(&priv->event_handler); - flush_scheduled_work(); + + rtnl_lock(); + dev_change_flags(priv->dev, priv->dev->flags & ~IFF_UP); + rtnl_unlock(); + + flush_workqueue(ipoib_workqueue); unregister_netdev(priv->dev); ipoib_dev_cleanup(priv->dev); diff --git a/drivers/infiniband/ulp/ipoib/ipoib_multicast.c b/drivers/infiniband/ulp/ipoib/ipoib_multicast.c index 8950e9546f4..ac33c8f3ea8 100644 --- a/drivers/infiniband/ulp/ipoib/ipoib_multicast.c +++ b/drivers/infiniband/ulp/ipoib/ipoib_multicast.c @@ -392,8 +392,16 @@ static int ipoib_mcast_join_complete(int status, &priv->mcast_task, 0); mutex_unlock(&mcast_mutex); - if (mcast == priv->broadcast) + if (mcast == priv->broadcast) { + /* + * Take RTNL lock here to avoid racing with + * ipoib_stop() and turning the carrier back + * on while a device is being removed. + */ + rtnl_lock(); netif_carrier_on(dev); + rtnl_unlock(); + } return 0; } -- GitLab From 7230ced4925b07c259a62b515d8278c6bb1ad98c Mon Sep 17 00:00:00 2001 From: Michael Ellerman Date: Thu, 31 Jul 2008 16:54:28 +1000 Subject: [PATCH 610/750] powerpc: Fix /dev/oldmem interface for kdump A change to __ioremap() broke reading /dev/oldmem because we're no longer able to ioremap pfn 0 (d177c207, "[PATCH] powerpc: IOMMU: don't ioremap null addresses"). We actually don't need to ioremap for anything that's part of the linear mapping, so just read it directly. Also make sure we're only reading one page or less at a time. Signed-off-by: Michael Ellerman Signed-off-by: Sachin Sant Signed-off-by: Paul Mackerras --- arch/powerpc/kernel/crash_dump.c | 31 ++++++++++++++++++++++--------- 1 file changed, 22 insertions(+), 9 deletions(-) diff --git a/arch/powerpc/kernel/crash_dump.c b/arch/powerpc/kernel/crash_dump.c index e0debcca0bf..a323c9b32ee 100644 --- a/arch/powerpc/kernel/crash_dump.c +++ b/arch/powerpc/kernel/crash_dump.c @@ -86,6 +86,19 @@ static int __init parse_savemaxmem(char *p) } __setup("savemaxmem=", parse_savemaxmem); + +static size_t copy_oldmem_vaddr(void *vaddr, char *buf, size_t csize, + unsigned long offset, int userbuf) +{ + if (userbuf) { + if (copy_to_user((char __user *)buf, (vaddr + offset), csize)) + return -EFAULT; + } else + memcpy(buf, (vaddr + offset), csize); + + return csize; +} + /** * copy_oldmem_page - copy one page from "oldmem" * @pfn: page frame number to be copied @@ -107,16 +120,16 @@ ssize_t copy_oldmem_page(unsigned long pfn, char *buf, if (!csize) return 0; - vaddr = __ioremap(pfn << PAGE_SHIFT, PAGE_SIZE, 0); + csize = min(csize, PAGE_SIZE); - if (userbuf) { - if (copy_to_user((char __user *)buf, (vaddr + offset), csize)) { - iounmap(vaddr); - return -EFAULT; - } - } else - memcpy(buf, (vaddr + offset), csize); + if (pfn < max_pfn) { + vaddr = __va(pfn << PAGE_SHIFT); + csize = copy_oldmem_vaddr(vaddr, buf, csize, offset, userbuf); + } else { + vaddr = __ioremap(pfn << PAGE_SHIFT, PAGE_SIZE, 0); + csize = copy_oldmem_vaddr(vaddr, buf, csize, offset, userbuf); + iounmap(vaddr); + } - iounmap(vaddr); return csize; } -- GitLab From 4589f1fe570c2c786b72eff146b2f168821882c6 Mon Sep 17 00:00:00 2001 From: Joachim Fenkes Date: Wed, 6 Aug 2008 00:30:18 +1000 Subject: [PATCH 611/750] powerpc/ibmebus: Restore "name" sysfs attribute on ibmebus devices Recent of_platform changes made of_bus_type_init() overwrite the bus type's .dev_attrs list, meaning that the "name" attribute that ibmebus devices previously had is no longer present. This is a user-visible regression which breaks the userspace eHCA support, since the eHCA userspace driver relies on the name attribute to check for valid adapters. This fixes it by providing the "name" attribute in the generic OF device code instead. Tested on POWER. Signed-off-by: Joachim Fenkes Signed-off-by: Paul Mackerras --- arch/powerpc/kernel/ibmebus.c | 12 ------------ drivers/of/device.c | 10 ++++++++++ 2 files changed, 10 insertions(+), 12 deletions(-) diff --git a/arch/powerpc/kernel/ibmebus.c b/arch/powerpc/kernel/ibmebus.c index 9d42eb57aea..a06362223f8 100644 --- a/arch/powerpc/kernel/ibmebus.c +++ b/arch/powerpc/kernel/ibmebus.c @@ -233,17 +233,6 @@ void ibmebus_free_irq(u32 ist, void *dev_id) } EXPORT_SYMBOL(ibmebus_free_irq); -static ssize_t name_show(struct device *dev, - struct device_attribute *attr, char *buf) -{ - return sprintf(buf, "%s\n", to_of_device(dev)->node->name); -} - -static struct device_attribute ibmebus_dev_attrs[] = { - __ATTR_RO(name), - __ATTR_NULL -}; - static char *ibmebus_chomp(const char *in, size_t count) { char *out = kmalloc(count + 1, GFP_KERNEL); @@ -327,7 +316,6 @@ static struct bus_attribute ibmebus_bus_attrs[] = { struct bus_type ibmebus_bus_type = { .uevent = of_device_uevent, - .dev_attrs = ibmebus_dev_attrs, .bus_attrs = ibmebus_bus_attrs }; EXPORT_SYMBOL(ibmebus_bus_type); diff --git a/drivers/of/device.c b/drivers/of/device.c index 8a1d93a2bb8..51e5214071d 100644 --- a/drivers/of/device.c +++ b/drivers/of/device.c @@ -57,6 +57,15 @@ static ssize_t devspec_show(struct device *dev, return sprintf(buf, "%s\n", ofdev->node->full_name); } +static ssize_t name_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct of_device *ofdev; + + ofdev = to_of_device(dev); + return sprintf(buf, "%s\n", ofdev->node->name); +} + static ssize_t modalias_show(struct device *dev, struct device_attribute *attr, char *buf) { @@ -71,6 +80,7 @@ static ssize_t modalias_show(struct device *dev, struct device_attribute of_platform_device_attrs[] = { __ATTR_RO(devspec), + __ATTR_RO(name), __ATTR_RO(modalias), __ATTR_NULL }; -- GitLab From cd5aeb9f6cf7ada6baa218e01b4299e201497cde Mon Sep 17 00:00:00 2001 From: Brian King Date: Wed, 13 Aug 2008 05:21:45 +1000 Subject: [PATCH 612/750] powerpc: Fix vio_bus_probe oops on probe error When CMO is enabled and booted on a non CMO system and the VIO device's probe function fails, an oops can result since vio_cmo_bus_remove is called when it should not. This fixes it by avoiding the vio_cmo_bus_remove call on platforms that don't implement CMO. cpu 0x0: Vector: 300 (Data Access) at [c00000000e13b3d0] pc: c000000000020d34: .vio_cmo_bus_remove+0xc0/0x1f4 lr: c000000000020ca4: .vio_cmo_bus_remove+0x30/0x1f4 sp: c00000000e13b650 msr: 8000000000009032 dar: 0 dsisr: 40000000 current = 0xc00000000e0566c0 paca = 0xc0000000006f9b80 pid = 2428, comm = modprobe enter ? for help [c00000000e13b6e0] c000000000021d94 .vio_bus_probe+0x2f8/0x33c [c00000000e13b7a0] c00000000029fc88 .driver_probe_device+0x13c/0x200 [c00000000e13b830] c00000000029fdac .__driver_attach+0x60/0xa4 [c00000000e13b8c0] c00000000029f050 .bus_for_each_dev+0x80/0xd8 [c00000000e13b980] c00000000029f9ec .driver_attach+0x28/0x40 [c00000000e13ba00] c00000000029f630 .bus_add_driver+0xd4/0x284 [c00000000e13baa0] c0000000002a01bc .driver_register+0xc4/0x198 [c00000000e13bb50] c00000000002168c .vio_register_driver+0x40/0x5c [c00000000e13bbe0] d0000000003b3f1c .ibmvfc_module_init+0x70/0x109c [ibmvfc] [c00000000e13bc70] c0000000000acf08 .sys_init_module+0x184c/0x1a10 [c00000000e13be30] c000000000008748 syscall_exit+0x0/0x40 Signed-off-by: Brian King Signed-off-by: Paul Mackerras --- arch/powerpc/kernel/vio.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/powerpc/kernel/vio.c b/arch/powerpc/kernel/vio.c index 22a3c33fd75..2750fbab197 100644 --- a/arch/powerpc/kernel/vio.c +++ b/arch/powerpc/kernel/vio.c @@ -1113,7 +1113,7 @@ static int vio_bus_probe(struct device *dev) return error; } error = viodrv->probe(viodev, id); - if (error) + if (error && firmware_has_feature(FW_FEATURE_CMO)) vio_cmo_bus_remove(viodev); } -- GitLab From 1b04624f93bb1c4f9495b8476d1dd0200af019e2 Mon Sep 17 00:00:00 2001 From: Roland McGrath Date: Tue, 19 Aug 2008 20:37:07 -0700 Subject: [PATCH 613/750] tracehook: fix SA_NOCLDWAIT I outwitted myself again in commit 2b2a1ff64afbadac842bbc58c5166962cf4f7664, and broke the SA_NOCLDWAIT behavior so it leaks zombies. This fixes it. Reported-by: Andi Kleen Signed-off-by: Roland McGrath --- kernel/signal.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/kernel/signal.c b/kernel/signal.c index c539f60c6f4..e661b01d340 100644 --- a/kernel/signal.c +++ b/kernel/signal.c @@ -1338,6 +1338,7 @@ int do_notify_parent(struct task_struct *tsk, int sig) struct siginfo info; unsigned long flags; struct sighand_struct *psig; + int ret = sig; BUG_ON(sig == -1); @@ -1402,7 +1403,7 @@ int do_notify_parent(struct task_struct *tsk, int sig) * is implementation-defined: we do (if you don't want * it, just use SIG_IGN instead). */ - tsk->exit_signal = -1; + ret = tsk->exit_signal = -1; if (psig->action[SIGCHLD-1].sa.sa_handler == SIG_IGN) sig = -1; } @@ -1411,7 +1412,7 @@ int do_notify_parent(struct task_struct *tsk, int sig) __wake_up_parent(tsk, tsk->parent); spin_unlock_irqrestore(&psig->siglock, flags); - return sig; + return ret; } static void do_notify_parent_cldstop(struct task_struct *tsk, int why) -- GitLab From c6744955d0ec0cb485c28c51eeb7185e260f6172 Mon Sep 17 00:00:00 2001 From: Samuel Sieb Date: Wed, 6 Aug 2008 22:06:29 -0700 Subject: [PATCH 614/750] x86: fix "kernel won't boot on a Cyrix MediaGXm (Geode)" Cyrix MediaGXm/Cx5530 Unicorn Revision 1.19.3B has stopped booting starting at v2.6.22. The reason is this commit: > commit f25f64ed5bd3c2932493681bdfdb483ea707da0a > Author: Juergen Beisert > Date: Sun Jul 22 11:12:38 2007 +0200 > > x86: Replace NSC/Cyrix specific chipset access macros by inlined functions. this commit activated a macro which was dormant before due to (buggy) macro side-effects. I've looked through various datasheets and found that the GXm and GXLV Geode processors don't have an incrementor. Remove the incrementor setup entirely. As the incrementor value differs according to clock speed and we would hope that the BIOS configures it correctly, it is probably the right solution. Cc: Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/cyrix.c | 18 ------------------ 1 file changed, 18 deletions(-) diff --git a/arch/x86/kernel/cpu/cyrix.c b/arch/x86/kernel/cpu/cyrix.c index 3fd7a67bb06..e710a21bb6e 100644 --- a/arch/x86/kernel/cpu/cyrix.c +++ b/arch/x86/kernel/cpu/cyrix.c @@ -134,23 +134,6 @@ static void __cpuinit set_cx86_memwb(void) setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x14); } -static void __cpuinit set_cx86_inc(void) -{ - unsigned char ccr3; - - printk(KERN_INFO "Enable Incrementor on Cyrix/NSC processor.\n"); - - ccr3 = getCx86(CX86_CCR3); - setCx86(CX86_CCR3, (ccr3 & 0x0f) | 0x10); /* enable MAPEN */ - /* PCR1 -- Performance Control */ - /* Incrementor on, whatever that is */ - setCx86(CX86_PCR1, getCx86(CX86_PCR1) | 0x02); - /* PCR0 -- Performance Control */ - /* Incrementor Margin 10 */ - setCx86(CX86_PCR0, getCx86(CX86_PCR0) | 0x04); - setCx86(CX86_CCR3, ccr3); /* disable MAPEN */ -} - /* * Configure later MediaGX and/or Geode processor. */ @@ -174,7 +157,6 @@ static void __cpuinit geode_configure(void) set_cx86_memwb(); set_cx86_reorder(); - set_cx86_inc(); local_irq_restore(flags); } -- GitLab From 80c5e73d6028e0f03ab0c70e7c4cbf98ac2e0c43 Mon Sep 17 00:00:00 2001 From: Venki Pallipadi Date: Tue, 19 Aug 2008 16:28:01 -0700 Subject: [PATCH 615/750] x86: fix Xorg startup/shutdown slowdown with PAT Rene Herman reported significant Xorg startup/shutdown slowdown due to PAT. It turns out that the memtype list has thousands of entries. Add cached_entry to list add routine, in order to speed up the lookup for sequential reserve_memtype calls. Reported-by: Rene Herman Signed-off-by: Venkatesh Pallipadi Signed-off-by: Ingo Molnar --- arch/x86/mm/pat.c | 33 +++++++++++++++++++++++++++++++-- 1 file changed, 31 insertions(+), 2 deletions(-) diff --git a/arch/x86/mm/pat.c b/arch/x86/mm/pat.c index 2fe30916d4b..bb6e8a267bf 100644 --- a/arch/x86/mm/pat.c +++ b/arch/x86/mm/pat.c @@ -207,6 +207,9 @@ static int chk_conflict(struct memtype *new, struct memtype *entry, return -EBUSY; } +static struct memtype *cached_entry; +static u64 cached_start; + /* * req_type typically has one of the: * - _PAGE_CACHE_WB @@ -280,11 +283,17 @@ int reserve_memtype(u64 start, u64 end, unsigned long req_type, spin_lock(&memtype_lock); + if (cached_entry && start >= cached_start) + entry = cached_entry; + else + entry = list_entry(&memtype_list, struct memtype, nd); + /* Search for existing mapping that overlaps the current range */ where = NULL; - list_for_each_entry(entry, &memtype_list, nd) { + list_for_each_entry_continue(entry, &memtype_list, nd) { if (end <= entry->start) { where = entry->nd.prev; + cached_entry = list_entry(where, struct memtype, nd); break; } else if (start <= entry->start) { /* end > entry->start */ err = chk_conflict(new, entry, new_type); @@ -292,6 +301,8 @@ int reserve_memtype(u64 start, u64 end, unsigned long req_type, dprintk("Overlap at 0x%Lx-0x%Lx\n", entry->start, entry->end); where = entry->nd.prev; + cached_entry = list_entry(where, + struct memtype, nd); } break; } else if (start < entry->end) { /* start > entry->start */ @@ -299,7 +310,20 @@ int reserve_memtype(u64 start, u64 end, unsigned long req_type, if (!err) { dprintk("Overlap at 0x%Lx-0x%Lx\n", entry->start, entry->end); - where = &entry->nd; + cached_entry = list_entry(entry->nd.prev, + struct memtype, nd); + + /* + * Move to right position in the linked + * list to add this new entry + */ + list_for_each_entry_continue(entry, + &memtype_list, nd) { + if (start <= entry->start) { + where = entry->nd.prev; + break; + } + } } break; } @@ -314,6 +338,8 @@ int reserve_memtype(u64 start, u64 end, unsigned long req_type, return err; } + cached_start = start; + if (where) list_add(&new->nd, where); else @@ -343,6 +369,9 @@ int free_memtype(u64 start, u64 end) spin_lock(&memtype_lock); list_for_each_entry(entry, &memtype_list, nd) { if (entry->start == start && entry->end == end) { + if (cached_entry == entry || cached_start == start) + cached_entry = NULL; + list_del(&entry->nd); kfree(entry); err = 0; -- GitLab From 99dd8713306a89f3e106143581244e550e00a644 Mon Sep 17 00:00:00 2001 From: Cliff Wickman Date: Tue, 19 Aug 2008 12:51:59 -0500 Subject: [PATCH 616/750] x86, SGI UV: hardcode the TLB flush interrupt system vector The UV TLB shootdown mechanism needs a system interrupt vector. Its vector had been hardcoded as 200, but needs to moved to the reserved system vector range so that it does not collide with some device vector. This is still temporary until dynamic system IRQ allocation is provided. But it will be needed when real UV hardware becomes available and runs 2.6.27. Signed-off-by: Cliff Wickman Signed-off-by: Ingo Molnar --- arch/x86/kernel/tlb_uv.c | 3 ++- include/asm-x86/irq_vectors.h | 1 + include/asm-x86/uv/uv_bau.h | 5 ----- 3 files changed, 3 insertions(+), 6 deletions(-) diff --git a/arch/x86/kernel/tlb_uv.c b/arch/x86/kernel/tlb_uv.c index d0fbb7712ab..8b8c0d6640f 100644 --- a/arch/x86/kernel/tlb_uv.c +++ b/arch/x86/kernel/tlb_uv.c @@ -17,6 +17,7 @@ #include #include #include +#include #include @@ -783,7 +784,7 @@ static int __init uv_bau_init(void) uv_init_blade(blade, node, cur_cpu); cur_cpu += uv_blade_nr_possible_cpus(blade); } - set_intr_gate(UV_BAU_MESSAGE, uv_bau_message_intr1); + alloc_intr_gate(UV_BAU_MESSAGE, uv_bau_message_intr1); uv_enable_timeouts(); return 0; diff --git a/include/asm-x86/irq_vectors.h b/include/asm-x86/irq_vectors.h index b95d167b7fb..a48c7f2dbdc 100644 --- a/include/asm-x86/irq_vectors.h +++ b/include/asm-x86/irq_vectors.h @@ -76,6 +76,7 @@ #define CALL_FUNCTION_SINGLE_VECTOR 0xfb #define THERMAL_APIC_VECTOR 0xfa #define THRESHOLD_APIC_VECTOR 0xf9 +#define UV_BAU_MESSAGE 0xf8 #define INVALIDATE_TLB_VECTOR_END 0xf7 #define INVALIDATE_TLB_VECTOR_START 0xf0 /* f0-f7 used for TLB flush */ diff --git a/include/asm-x86/uv/uv_bau.h b/include/asm-x86/uv/uv_bau.h index 91ac0dfb758..610b6b308e9 100644 --- a/include/asm-x86/uv/uv_bau.h +++ b/include/asm-x86/uv/uv_bau.h @@ -40,11 +40,6 @@ #define UV_ACTIVATION_DESCRIPTOR_SIZE 32 #define UV_DISTRIBUTION_SIZE 256 #define UV_SW_ACK_NPENDING 8 -#define UV_BAU_MESSAGE 200 -/* - * Messaging irq; see irq_64.h and include/asm-x86/hw_irq_64.h - * To be dynamically allocated in the future - */ #define UV_NET_ENDPOINT_INTD 0x38 #define UV_DESC_BASE_PNODE_SHIFT 49 #define UV_PAYLOADQ_PNODE_SHIFT 49 -- GitLab From 80a8c9fffa78f57d7d4351af2f15a56386805ceb Mon Sep 17 00:00:00 2001 From: Andi Kleen Date: Tue, 19 Aug 2008 03:13:38 +0200 Subject: [PATCH 617/750] x86: fix oprofile + hibernation badness Vegard Nossum reported oprofile + hibernation problems: > Now some warnings: > > ------------[ cut here ]------------ > WARNING: at /uio/arkimedes/s29/vegardno/git-working/linux-2.6/kernel/smp.c:328 s > mp_call_function_mask+0x194/0x1a0() The usual problem: the suspend function when interrupts are already disabled calls smp_call_function which is not allowed with interrupt off. But at this point all the other CPUs should be already down anyways, so it should be enough to just drop that. This patch should fix that problem at least by fixing cpu hotplug& suspend support. [ mingo@elte.hu: fixed 5 coding style errors. ] Signed-off-by: Andi Kleen Tested-by: Vegard Nossum Signed-off-by: Ingo Molnar --- arch/x86/oprofile/nmi_int.c | 39 ++++++++++++++++++++++++++++++++++--- 1 file changed, 36 insertions(+), 3 deletions(-) diff --git a/arch/x86/oprofile/nmi_int.c b/arch/x86/oprofile/nmi_int.c index 3f90289410e..0227694f7da 100644 --- a/arch/x86/oprofile/nmi_int.c +++ b/arch/x86/oprofile/nmi_int.c @@ -15,6 +15,7 @@ #include #include #include +#include #include #include #include @@ -28,23 +29,48 @@ static DEFINE_PER_CPU(unsigned long, saved_lvtpc); static int nmi_start(void); static void nmi_stop(void); +static void nmi_cpu_start(void *dummy); +static void nmi_cpu_stop(void *dummy); /* 0 == registered but off, 1 == registered and on */ static int nmi_enabled = 0; +#ifdef CONFIG_SMP +static int oprofile_cpu_notifier(struct notifier_block *b, unsigned long action, + void *data) +{ + int cpu = (unsigned long)data; + switch (action) { + case CPU_DOWN_FAILED: + case CPU_ONLINE: + smp_call_function_single(cpu, nmi_cpu_start, NULL, 0); + break; + case CPU_DOWN_PREPARE: + smp_call_function_single(cpu, nmi_cpu_stop, NULL, 1); + break; + } + return NOTIFY_DONE; +} + +static struct notifier_block oprofile_cpu_nb = { + .notifier_call = oprofile_cpu_notifier +}; +#endif + #ifdef CONFIG_PM static int nmi_suspend(struct sys_device *dev, pm_message_t state) { + /* Only one CPU left, just stop that one */ if (nmi_enabled == 1) - nmi_stop(); + nmi_cpu_stop(NULL); return 0; } static int nmi_resume(struct sys_device *dev) { if (nmi_enabled == 1) - nmi_start(); + nmi_cpu_start(NULL); return 0; } @@ -463,6 +489,9 @@ int __init op_nmi_init(struct oprofile_operations *ops) } init_sysfs(); +#ifdef CONFIG_SMP + register_cpu_notifier(&oprofile_cpu_nb); +#endif using_nmi = 1; ops->create_files = nmi_create_files; ops->setup = nmi_setup; @@ -476,6 +505,10 @@ int __init op_nmi_init(struct oprofile_operations *ops) void op_nmi_exit(void) { - if (using_nmi) + if (using_nmi) { exit_sysfs(); +#ifdef CONFIG_SMP + unregister_cpu_notifier(&oprofile_cpu_nb); +#endif + } } -- GitLab From 5f22ca9b13551debea77a407a8d06cd9c6f15238 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Wed, 20 Aug 2008 08:31:19 -0700 Subject: [PATCH 618/750] vfat: fix 'sync' mount deadlock due to BKL->lock_super conversion There was another FAT BKL conversion deadlock reported by Bart Trojanowski due to the BKL being used as a recursive lock by FAT, which was missed because it only triggers with 'sync' (or 'dirsync') mounts. The recursion worked for the BKL, but after the conversion to lock_super (which uses a mutex), it just deadlocks. Thanks to Bart for debugging this and testing the fix. The lock debugging information from the original report: ============================================= [ INFO: possible recursive locking detected ] 2.6.27-rc3-bisect-00448-ga7f5aaf #16 --------------------------------------------- mv/4020 is trying to acquire lock: (&type->s_lock_key#9){--..}, at: [] lock_super+0x1e/0x20 but task is already holding lock: (&type->s_lock_key#9){--..}, at: [] lock_super+0x1e/0x20 other info that might help us debug this: 3 locks held by mv/4020: #0: (&sb->s_type->i_mutex_key#9/1){--..}, at: [] do_unlinkat+0x66/0x140 #1: (&sb->s_type->i_mutex_key#9){--..}, at: [] vfs_unlink+0x84/0x110 #2: (&type->s_lock_key#9){--..}, at: [] lock_super+0x1e/0x20 stack backtrace: Pid: 4020, comm: mv Not tainted 2.6.27-rc3-bisect-00448-ga7f5aaf #16 [] validate_chain+0x984/0xea0 [] ? native_sched_clock+0x0/0xf0 [] __lock_acquire+0x2ec/0x9b0 [] lock_acquire+0x6f/0x90 [] ? lock_super+0x1e/0x20 [] mutex_lock_nested+0xad/0x300 [] ? lock_super+0x1e/0x20 [] ? lock_super+0x1e/0x20 [] lock_super+0x1e/0x20 [] fat_write_inode+0x60/0x2b0 [fat] [] ? _spin_unlock_irqrestore+0x48/0x80 [] ? fat_sync_inode+0x3/0x20 [fat] [] fat_sync_inode+0x12/0x20 [fat] [] fat_remove_entries+0xbe/0x120 [fat] [] vfat_unlink+0x5f/0x90 [vfat] [] ? vfat_unlink+0x0/0x90 [vfat] [] vfs_unlink+0x98/0x110 [] do_unlinkat+0x130/0x140 [] ? audit_syscall_entry+0x105/0x150 [] sys_unlinkat+0x3b/0x40 [] sysenter_do_call+0x12/0x3f ======================= where the deadlock is due to the nesting of lock_super from vfat_unlink to fat_write_inode: - do_unlinkat - vfs_unlink - vfat_unlink * lock_super - fat_remove_entries - fat_sync_inode - fat_write_inode * lock_super and the fix is to simply remove the use of lock_super() in fat_write_inode. The lock_super() there had been just an automatic conversion of the kernel lock to the superblock lock, but no locking was actually needed there, since the code in fat_write_inode already protected all relevant accesses with a spinlock (sbi->inode_hash_lock to be exact). The only code inside the BKL (and thus the superblock lock) was accesses tp local variables or calls to functions that have long been SMP-safe (i.e. sb_bread, mark_buffe_dirty and brlese). Bart reports: "Looks good. I ran 10 parallel processes creating 1M files truncating them, writing to them again and then deleting them. This patch fixes the issue I ran into. Signed-off-by: Bart Trojanowski " Reported-and-tested-by: Bart Trojanowski Signed-off-by: Linus Torvalds --- fs/fat/inode.c | 10 +++------- 1 file changed, 3 insertions(+), 7 deletions(-) diff --git a/fs/fat/inode.c b/fs/fat/inode.c index 6d266d793e2..80ff3381fa2 100644 --- a/fs/fat/inode.c +++ b/fs/fat/inode.c @@ -562,26 +562,23 @@ static int fat_write_inode(struct inode *inode, int wait) struct buffer_head *bh; struct msdos_dir_entry *raw_entry; loff_t i_pos; - int err = 0; + int err; retry: i_pos = MSDOS_I(inode)->i_pos; if (inode->i_ino == MSDOS_ROOT_INO || !i_pos) return 0; - lock_super(sb); bh = sb_bread(sb, i_pos >> sbi->dir_per_block_bits); if (!bh) { printk(KERN_ERR "FAT: unable to read inode block " "for updating (i_pos %lld)\n", i_pos); - err = -EIO; - goto out; + return -EIO; } spin_lock(&sbi->inode_hash_lock); if (i_pos != MSDOS_I(inode)->i_pos) { spin_unlock(&sbi->inode_hash_lock); brelse(bh); - unlock_super(sb); goto retry; } @@ -607,11 +604,10 @@ retry: } spin_unlock(&sbi->inode_hash_lock); mark_buffer_dirty(bh); + err = 0; if (wait) err = sync_dirty_buffer(bh); brelse(bh); -out: - unlock_super(sb); return err; } -- GitLab From 1c8e40e4064d51ec50258c4d381eb832c0b231db Mon Sep 17 00:00:00 2001 From: David Woodhouse Date: Wed, 20 Aug 2008 14:44:45 +0100 Subject: [PATCH 619/750] Reduce brokenness of CRIS headers_install I won't say 'fix', because they still look broken, although this will at least allow 'make ARCH=CRIS headers_install' to _complete_. For headers which are exported, we should probably choose between asm/arch-v10 and asm/arch-v32 by something that GCC defines -- we can't rely on a generated symlink. And we certainly can't export an arch/ directory which doesn't even exist. And the only thing that we seem to include from the arch/ directory is from ... and that isn't exported in either arch-v10 or arch-v32 _anyway_. Signed-off-by: David Woodhouse Signed-off-by: Linus Torvalds --- include/asm-cris/Kbuild | 1 - 1 file changed, 1 deletion(-) diff --git a/include/asm-cris/Kbuild b/include/asm-cris/Kbuild index b7037d80d46..d5b631935ec 100644 --- a/include/asm-cris/Kbuild +++ b/include/asm-cris/Kbuild @@ -1,6 +1,5 @@ include include/asm-generic/Kbuild.asm -header-y += arch/ header-y += arch-v10/ header-y += arch-v32/ -- GitLab From e4464facd6f1404c2baeb6798d71e34423e7aeaa Mon Sep 17 00:00:00 2001 From: David Woodhouse Date: Wed, 20 Aug 2008 14:58:23 +0100 Subject: [PATCH 620/750] Reserve NFS fileid values for btrfs Purely cosmetic for now, but we might as well get it merged ASAP. Signed-off-by: David Woodhouse Signed-off-by: Linus Torvalds --- include/linux/exportfs.h | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+) diff --git a/include/linux/exportfs.h b/include/linux/exportfs.h index f5abd130663..27e772cefb6 100644 --- a/include/linux/exportfs.h +++ b/include/linux/exportfs.h @@ -34,6 +34,27 @@ enum fid_type { */ FILEID_INO32_GEN_PARENT = 2, + /* + * 64 bit object ID, 64 bit root object ID, + * 32 bit generation number. + */ + FILEID_BTRFS_WITHOUT_PARENT = 0x4d, + + /* + * 64 bit object ID, 64 bit root object ID, + * 32 bit generation number, + * 64 bit parent object ID, 32 bit parent generation. + */ + FILEID_BTRFS_WITH_PARENT = 0x4e, + + /* + * 64 bit object ID, 64 bit root object ID, + * 32 bit generation number, + * 64 bit parent object ID, 32 bit parent generation, + * 64 bit parent root object ID. + */ + FILEID_BTRFS_WITH_PARENT_ROOT = 0x4f, + /* * 32 bit block number, 16 bit partition reference, * 16 bit unused, 32 bit generation number. -- GitLab From 449f76506f76051839dfa945c59881c17509cfbf Mon Sep 17 00:00:00 2001 From: David Howells Date: Wed, 20 Aug 2008 15:53:33 +0100 Subject: [PATCH 621/750] MN10300: Supply ioremap_wc() for MN10300 Supply ioremap_wc() for MN10300. Signed-off-by: David Howells Signed-off-by: Linus Torvalds --- include/asm-mn10300/io.h | 2 ++ 1 file changed, 2 insertions(+) diff --git a/include/asm-mn10300/io.h b/include/asm-mn10300/io.h index b8b6dc87825..c1a4119e649 100644 --- a/include/asm-mn10300/io.h +++ b/include/asm-mn10300/io.h @@ -259,6 +259,8 @@ static inline void *ioremap_nocache(unsigned long offset, unsigned long size) return (void *) (offset | 0x20000000); } +#define ioremap_wc ioremap_nocache + static inline void iounmap(void *addr) { } -- GitLab From 0c7281c0faa1d0bdbdc647430cbdf7e0aed7f385 Mon Sep 17 00:00:00 2001 From: David Howells Date: Wed, 20 Aug 2008 16:04:22 +0100 Subject: [PATCH 622/750] FRV: Provide ioremap_wc() for FRV Provide ioremap_wc() for FRV. Signed-off-by: David Howells Signed-off-by: Linus Torvalds --- include/asm-frv/io.h | 2 ++ 1 file changed, 2 insertions(+) diff --git a/include/asm-frv/io.h b/include/asm-frv/io.h index 20e44fe00ab..ca7475e73b5 100644 --- a/include/asm-frv/io.h +++ b/include/asm-frv/io.h @@ -271,6 +271,8 @@ static inline void __iomem *ioremap_fullcache(unsigned long physaddr, unsigned l return __ioremap(physaddr, size, IOMAP_FULL_CACHING); } +#define ioremap_wc ioremap_nocache + extern void iounmap(void volatile __iomem *addr); static inline void __iomem *ioport_map(unsigned long port, unsigned int nr) -- GitLab From 55d8460c921ed725f5bf46c826a6bddbe8a75c46 Mon Sep 17 00:00:00 2001 From: Mike Rapoport Date: Wed, 20 Aug 2008 06:10:06 +0100 Subject: [PATCH 623/750] [ARM] 5212/1: pxa: fix build error when CPU_PXA310 is not defined Fix arch/arm/mach-pxa/pxa300.c:94: error: 'CKEN_MMC3' undeclared here (not in a function) when building for PXA300. Signed-off-by: Mike Rapoport Acked-by: Eric Miao Signed-off-by: Russell King --- arch/arm/mach-pxa/pxa300.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/mach-pxa/pxa300.c b/arch/arm/mach-pxa/pxa300.c index 494fc1f032d..9adc7fc4618 100644 --- a/arch/arm/mach-pxa/pxa300.c +++ b/arch/arm/mach-pxa/pxa300.c @@ -90,7 +90,9 @@ static struct clk common_clks[] = { }; static struct clk pxa310_clks[] = { +#ifdef CONFIG_CPU_PXA310 PXA3xx_CKEN("MMCCLK", MMC3, 19500000, 0, &pxa3xx_device_mci3.dev), +#endif }; static int __init pxa300_init(void) -- GitLab From f14413184b1de4dcbd5ec3e7c129c3ce2079f543 Mon Sep 17 00:00:00 2001 From: Matthew Garrett Date: Wed, 20 Aug 2008 14:08:57 -0700 Subject: [PATCH 624/750] eeepc-laptop: fix use after free eeepc-laptop uses the hwmon struct after unregistering the device, causing an oops on module unload. Flip the ordering to fix. Signed-off-by: Matthew Garrett Cc: Henrique de Moraes Holschuh Cc: Corentin Chary Cc: Karol Kozimor Cc: [2.6.26.x] Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/misc/eeepc-laptop.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/misc/eeepc-laptop.c b/drivers/misc/eeepc-laptop.c index 9e8d79e7e9f..facdb9893c8 100644 --- a/drivers/misc/eeepc-laptop.c +++ b/drivers/misc/eeepc-laptop.c @@ -553,9 +553,9 @@ static void eeepc_hwmon_exit(void) hwmon = eeepc_hwmon_device; if (!hwmon) return ; - hwmon_device_unregister(hwmon); sysfs_remove_group(&hwmon->kobj, &hwmon_attribute_group); + hwmon_device_unregister(hwmon); eeepc_hwmon_device = NULL; } -- GitLab From 35fc908dc0e7ab0002ef18787886cc1340028020 Mon Sep 17 00:00:00 2001 From: Andreas Herrmann Date: Wed, 20 Aug 2008 14:08:58 -0700 Subject: [PATCH 625/750] documentation: describe bootmem_debug kernel parameter "bootmem_debug" is not mentioned in kernel-parameters.txt. Recently I had to use that kernel option and I think it should be documented. Signed-off-by: Andreas Herrmann Cc: Ingo Molnar Cc: Randy Dunlap Cc: Johannes Weiner Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/kernel-parameters.txt | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index e7bea3e8530..a8976467a98 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -365,6 +365,8 @@ and is between 256 and 4096 characters. It is defined in the file no delay (0). Format: integer + bootmem_debug [KNL] Enable bootmem allocator debug messages. + bttv.card= [HW,V4L] bttv (bt848 + bt878 based grabber cards) bttv.radio= Most important insmod options are available as kernel args too. -- GitLab From 1804dc6e145f3f24a8c94deddfc0a986d380a27f Mon Sep 17 00:00:00 2001 From: Clement Calmels Date: Wed, 20 Aug 2008 14:09:00 -0700 Subject: [PATCH 626/750] /proc/self/maps doesn't display the real file offset This addresses http://bugzilla.kernel.org/show_bug.cgi?id=11318 In function show_map (file: fs/proc/task_mmu.c), if vma->vm_pgoff > 2^20 than (vma->vm_pgoff << PAGE_SIZE) is greater than 2^32 (with PAGE_SIZE equal to 4096 (i.e. 2^12). The next seq_printf use an unsigned long for the conversion of (vma->vm_pgoff << PAGE_SIZE), as a result the offset value displayed in /proc/self/maps is truncated if the page offset is greater than 2^20. A test that shows this issue: #define _GNU_SOURCE #include #include #include #include #include #include #include #include #define PAGE_SIZE (getpagesize()) #if __i386__ # define U64_STR "%llx" #elif __x86_64 # define U64_STR "%lx" #else # error "Architecture Unsupported" #endif int main(int argc, char *argv[]) { int fd; char *addr; off64_t offset = 0x10000000; char *filename = "/dev/zero"; fd = open(filename, O_RDONLY); if (fd < 0) { perror("open"); return 1; } offset *= 0x10; printf("offset = " U64_STR "\n", offset); addr = (char*)mmap64(NULL, PAGE_SIZE, PROT_READ, MAP_PRIVATE, fd, offset); if ((void*)addr == MAP_FAILED) { perror("mmap64"); return 1; } { FILE *fmaps; char *line = NULL; size_t len = 0; ssize_t read; size_t filename_len = strlen(filename); fmaps = fopen("/proc/self/maps", "r"); if (!fmaps) { perror("fopen"); return 1; } while ((read = getline(&line, &len, fmaps)) != -1) { if ((read > filename_len + 1) && (strncmp(&line[read - filename_len - 1], filename, filename_len) == 0)) printf("%s", line); } if (line) free(line); fclose(fmaps); } close(fd); return 0; } [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Clement Calmels Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- fs/proc/nommu.c | 4 ++-- fs/proc/task_mmu.c | 4 ++-- 2 files changed, 4 insertions(+), 4 deletions(-) diff --git a/fs/proc/nommu.c b/fs/proc/nommu.c index 79ecd281d2c..3f87d263294 100644 --- a/fs/proc/nommu.c +++ b/fs/proc/nommu.c @@ -52,14 +52,14 @@ int nommu_vma_show(struct seq_file *m, struct vm_area_struct *vma) } seq_printf(m, - "%08lx-%08lx %c%c%c%c %08lx %02x:%02x %lu %n", + "%08lx-%08lx %c%c%c%c %08llx %02x:%02x %lu %n", vma->vm_start, vma->vm_end, flags & VM_READ ? 'r' : '-', flags & VM_WRITE ? 'w' : '-', flags & VM_EXEC ? 'x' : '-', flags & VM_MAYSHARE ? flags & VM_SHARED ? 'S' : 's' : 'p', - vma->vm_pgoff << PAGE_SHIFT, + ((loff_t)vma->vm_pgoff) << PAGE_SHIFT, MAJOR(dev), MINOR(dev), ino, &len); if (file) { diff --git a/fs/proc/task_mmu.c b/fs/proc/task_mmu.c index 7546a918f79..73d1891ee62 100644 --- a/fs/proc/task_mmu.c +++ b/fs/proc/task_mmu.c @@ -219,14 +219,14 @@ static int show_map(struct seq_file *m, void *v) ino = inode->i_ino; } - seq_printf(m, "%08lx-%08lx %c%c%c%c %08lx %02x:%02x %lu %n", + seq_printf(m, "%08lx-%08lx %c%c%c%c %08llx %02x:%02x %lu %n", vma->vm_start, vma->vm_end, flags & VM_READ ? 'r' : '-', flags & VM_WRITE ? 'w' : '-', flags & VM_EXEC ? 'x' : '-', flags & VM_MAYSHARE ? 's' : 'p', - vma->vm_pgoff << PAGE_SHIFT, + ((loff_t)vma->vm_pgoff) << PAGE_SHIFT, MAJOR(dev), MINOR(dev), ino, &len); /* -- GitLab From fe2e1cf83a46c879a66ec5146ba7a09a6aef0a5c Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Wed, 20 Aug 2008 14:09:01 -0700 Subject: [PATCH 627/750] Blackfin RTC Driver: move irq request/free out of open/release and into probe/remove so that the non-dev interfaces (like sysfs) work as expected Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu Cc: Alessandro Zummo Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/rtc/rtc-bfin.c | 51 +++++++++++++++++------------------------- 1 file changed, 20 insertions(+), 31 deletions(-) diff --git a/drivers/rtc/rtc-bfin.c b/drivers/rtc/rtc-bfin.c index a1af4c27939..51741dc1291 100644 --- a/drivers/rtc/rtc-bfin.c +++ b/drivers/rtc/rtc-bfin.c @@ -218,26 +218,6 @@ static irqreturn_t bfin_rtc_interrupt(int irq, void *dev_id) return IRQ_NONE; } -static int bfin_rtc_open(struct device *dev) -{ - int ret; - - dev_dbg_stamp(dev); - - ret = request_irq(IRQ_RTC, bfin_rtc_interrupt, IRQF_SHARED, to_platform_device(dev)->name, dev); - if (!ret) - bfin_rtc_reset(dev, RTC_ISTAT_WRITE_COMPLETE); - - return ret; -} - -static void bfin_rtc_release(struct device *dev) -{ - dev_dbg_stamp(dev); - bfin_rtc_reset(dev, 0); - free_irq(IRQ_RTC, dev); -} - static void bfin_rtc_int_set(u16 rtc_int) { bfin_write_RTC_ISTAT(rtc_int); @@ -370,8 +350,6 @@ static int bfin_rtc_proc(struct device *dev, struct seq_file *seq) } static struct rtc_class_ops bfin_rtc_ops = { - .open = bfin_rtc_open, - .release = bfin_rtc_release, .ioctl = bfin_rtc_ioctl, .read_time = bfin_rtc_read_time, .set_time = bfin_rtc_set_time, @@ -383,29 +361,37 @@ static struct rtc_class_ops bfin_rtc_ops = { static int __devinit bfin_rtc_probe(struct platform_device *pdev) { struct bfin_rtc *rtc; + struct device *dev = &pdev->dev; int ret = 0; - dev_dbg_stamp(&pdev->dev); + dev_dbg_stamp(dev); + /* Allocate memory for our RTC struct */ rtc = kzalloc(sizeof(*rtc), GFP_KERNEL); if (unlikely(!rtc)) return -ENOMEM; + platform_set_drvdata(pdev, rtc); - rtc->rtc_dev = rtc_device_register(pdev->name, &pdev->dev, &bfin_rtc_ops, THIS_MODULE); - if (IS_ERR(rtc)) { - ret = PTR_ERR(rtc->rtc_dev); + /* Grab the IRQ and init the hardware */ + ret = request_irq(IRQ_RTC, bfin_rtc_interrupt, IRQF_SHARED, pdev->name, dev); + if (unlikely(ret)) goto err; - } - - /* see comment at top of file about stopwatch/PIE */ + bfin_rtc_reset(dev, RTC_ISTAT_WRITE_COMPLETE); bfin_write_RTC_SWCNT(0); - platform_set_drvdata(pdev, rtc); + /* Register our RTC with the RTC framework */ + rtc->rtc_dev = rtc_device_register(pdev->name, dev, &bfin_rtc_ops, THIS_MODULE); + if (unlikely(IS_ERR(rtc))) { + ret = PTR_ERR(rtc->rtc_dev); + goto err_irq; + } - device_init_wakeup(&pdev->dev, 1); + device_init_wakeup(dev, 1); return 0; + err_irq: + free_irq(IRQ_RTC, dev); err: kfree(rtc); return ret; @@ -414,7 +400,10 @@ static int __devinit bfin_rtc_probe(struct platform_device *pdev) static int __devexit bfin_rtc_remove(struct platform_device *pdev) { struct bfin_rtc *rtc = platform_get_drvdata(pdev); + struct device *dev = &pdev->dev; + bfin_rtc_reset(dev, 0); + free_irq(IRQ_RTC, dev); rtc_device_unregister(rtc->rtc_dev); platform_set_drvdata(pdev, NULL); kfree(rtc); -- GitLab From 8c9166f7a60b67909632ea60a032c18d84ed8af0 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Wed, 20 Aug 2008 14:09:02 -0700 Subject: [PATCH 628/750] Blackfin RTC Driver: do all initialization before we register the rtc and make it available Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu Cc: Alessandro Zummo Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/rtc/rtc-bfin.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/drivers/rtc/rtc-bfin.c b/drivers/rtc/rtc-bfin.c index 51741dc1291..9d2da1cd777 100644 --- a/drivers/rtc/rtc-bfin.c +++ b/drivers/rtc/rtc-bfin.c @@ -371,6 +371,7 @@ static int __devinit bfin_rtc_probe(struct platform_device *pdev) if (unlikely(!rtc)) return -ENOMEM; platform_set_drvdata(pdev, rtc); + device_init_wakeup(dev, 1); /* Grab the IRQ and init the hardware */ ret = request_irq(IRQ_RTC, bfin_rtc_interrupt, IRQF_SHARED, pdev->name, dev); @@ -386,8 +387,6 @@ static int __devinit bfin_rtc_probe(struct platform_device *pdev) goto err_irq; } - device_init_wakeup(dev, 1); - return 0; err_irq: -- GitLab From 7f60459921bd24e86b21e07c42244c510b4f46b2 Mon Sep 17 00:00:00 2001 From: Graf Yang Date: Wed, 20 Aug 2008 14:09:02 -0700 Subject: [PATCH 629/750] Blackfin RTC Driver: BF561 not have on-chip RTC Signed-off-by: Graf Yang Signed-off-by: Bryan Wu Cc: Alessandro Zummo Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/rtc/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig index 90ab7382540..9a9755c92fa 100644 --- a/drivers/rtc/Kconfig +++ b/drivers/rtc/Kconfig @@ -561,7 +561,7 @@ config RTC_DRV_AT91SAM9_GPBR config RTC_DRV_BFIN tristate "Blackfin On-Chip RTC" - depends on BLACKFIN + depends on BLACKFIN && !BF561 help If you say yes here you will get support for the Blackfin On-Chip Real Time Clock. -- GitLab From d0fd93781c49cbe127f9e7a5b402e9b167c105a6 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Wed, 20 Aug 2008 14:09:03 -0700 Subject: [PATCH 630/750] Blackfin RTC Driver: dont let RTC programming in bootloaders randomly cause ~5 second boot delays Signed-off-by: Mike Frysinger Signed-off-by: Bryan Wu Cc: Alessandro Zummo Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/rtc/rtc-bfin.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/drivers/rtc/rtc-bfin.c b/drivers/rtc/rtc-bfin.c index 9d2da1cd777..34439ce3967 100644 --- a/drivers/rtc/rtc-bfin.c +++ b/drivers/rtc/rtc-bfin.c @@ -363,6 +363,7 @@ static int __devinit bfin_rtc_probe(struct platform_device *pdev) struct bfin_rtc *rtc; struct device *dev = &pdev->dev; int ret = 0; + unsigned long timeout; dev_dbg_stamp(dev); @@ -377,6 +378,13 @@ static int __devinit bfin_rtc_probe(struct platform_device *pdev) ret = request_irq(IRQ_RTC, bfin_rtc_interrupt, IRQF_SHARED, pdev->name, dev); if (unlikely(ret)) goto err; + /* sometimes the bootloader touched things, but the write complete was not + * enabled, so let's just do a quick timeout here since the IRQ will not fire ... + */ + timeout = jiffies + HZ; + while (bfin_read_RTC_ISTAT() & RTC_ISTAT_WRITE_PENDING) + if (time_after(jiffies, timeout)) + break; bfin_rtc_reset(dev, RTC_ISTAT_WRITE_COMPLETE); bfin_write_RTC_SWCNT(0); -- GitLab From 16f8c5b2e64dec7faa5d3c7e9bdf0765e864e481 Mon Sep 17 00:00:00 2001 From: Hugh Dickins Date: Wed, 20 Aug 2008 14:09:04 -0700 Subject: [PATCH 631/750] mm: page_remove_rmap comments on PageAnon Add a comment to s390's page_test_dirty/page_clear_dirty/page_set_dirty dance in page_remove_rmap(): I was wrong to think the PageSwapCache test could be avoided, and would like a comment in there to remind me. And mention s390, to help us remember that this block is not really common. Also move down the "It would be tidy to reset PageAnon" comment: it does not belong to s390's block, and it would be unwise to reset PageAnon before we're done with testing it. Signed-off-by: Hugh Dickins Acked-by: Martin Schwidefsky Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- mm/rmap.c | 25 ++++++++++++++++--------- 1 file changed, 16 insertions(+), 9 deletions(-) diff --git a/mm/rmap.c b/mm/rmap.c index 1ea4e6fcee7..059774712c0 100644 --- a/mm/rmap.c +++ b/mm/rmap.c @@ -659,23 +659,30 @@ void page_remove_rmap(struct page *page, struct vm_area_struct *vma) } /* - * It would be tidy to reset the PageAnon mapping here, - * but that might overwrite a racing page_add_anon_rmap - * which increments mapcount after us but sets mapping - * before us: so leave the reset to free_hot_cold_page, - * and remember that it's only reliable while mapped. - * Leaving it set also helps swapoff to reinstate ptes - * faster for those pages still in swapcache. + * Now that the last pte has gone, s390 must transfer dirty + * flag from storage key to struct page. We can usually skip + * this if the page is anon, so about to be freed; but perhaps + * not if it's in swapcache - there might be another pte slot + * containing the swap entry, but page not yet written to swap. */ if ((!PageAnon(page) || PageSwapCache(page)) && page_test_dirty(page)) { page_clear_dirty(page); set_page_dirty(page); } - mem_cgroup_uncharge_page(page); + mem_cgroup_uncharge_page(page); __dec_zone_page_state(page, - PageAnon(page) ? NR_ANON_PAGES : NR_FILE_MAPPED); + PageAnon(page) ? NR_ANON_PAGES : NR_FILE_MAPPED); + /* + * It would be tidy to reset the PageAnon mapping here, + * but that might overwrite a racing page_add_anon_rmap + * which increments mapcount after us but sets mapping + * before us: so leave the reset to free_hot_cold_page, + * and remember that it's only reliable while mapped. + * Leaving it set also helps swapoff to reinstate ptes + * faster for those pages still in swapcache. + */ } } -- GitLab From 07279cdfd964acc032de92a527cb11b1f40f35aa Mon Sep 17 00:00:00 2001 From: Hugh Dickins Date: Wed, 20 Aug 2008 14:09:05 -0700 Subject: [PATCH 632/750] mm: show free swap as signed Adjust m show_swap_cache_info() to show "Free swap" as a signed long: the signed format is preferable, because during swapoff nr_swap_pages can legitimately go negative, so makes more sense thus (it used to be shown redundantly, once as signed and once as unsigned). Signed-off-by: Hugh Dickins Reviewed-by: KOSAKI Motohiro Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- mm/swap_state.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/mm/swap_state.c b/mm/swap_state.c index 167cf2dc8a0..797c3831cbe 100644 --- a/mm/swap_state.c +++ b/mm/swap_state.c @@ -60,7 +60,7 @@ void show_swap_cache_info(void) printk("Swap cache stats: add %lu, delete %lu, find %lu/%lu\n", swap_cache_info.add_total, swap_cache_info.del_total, swap_cache_info.find_success, swap_cache_info.find_total); - printk("Free swap = %lukB\n", nr_swap_pages << (PAGE_SHIFT - 10)); + printk("Free swap = %ldkB\n", nr_swap_pages << (PAGE_SHIFT - 10)); printk("Total swap = %lukB\n", total_swap_pages << (PAGE_SHIFT - 10)); } -- GitLab From 759f9a2df78d2156a2675edc7999fb4c919a3159 Mon Sep 17 00:00:00 2001 From: Marcin Slusarz Date: Wed, 20 Aug 2008 14:09:06 -0700 Subject: [PATCH 633/750] mm: mminit_loglevel cannot be __meminitdata anymore mminit_loglevel is now used from mminit_verify_zonelist <- build_all_zonelists <- 1. online_pages <- memory_block_action <- memory_block_change_state <- store_mem_state (sys handler) 2. numa_zonelist_order_handler (proc handler) so it cannot be annotated __meminit - drop it fixes following section mismatch warning: WARNING: vmlinux.o(.text+0x71628): Section mismatch in reference from the function mminit_verify_zonelist() to the variable .meminit.data:mminit_loglevel The function mminit_verify_zonelist() references the variable __meminitdata mminit_loglevel. This is often because mminit_verify_zonelist lacks a __meminitdata annotation or the annotation of mminit_loglevel is wrong. Signed-off-by: Marcin Slusarz Acked-by: Mel Gorman Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- mm/mm_init.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/mm/mm_init.c b/mm/mm_init.c index 936ef2efd89..4e0e26591df 100644 --- a/mm/mm_init.c +++ b/mm/mm_init.c @@ -12,7 +12,7 @@ #include "internal.h" #ifdef CONFIG_DEBUG_MEMORY_INIT -int __meminitdata mminit_loglevel; +int mminit_loglevel; #ifndef SECTIONS_SHIFT #define SECTIONS_SHIFT 0 -- GitLab From f3944d61ddc65722539ffd7b6f5b7c7217c136cc Mon Sep 17 00:00:00 2001 From: Sven Wegener Date: Wed, 20 Aug 2008 14:09:07 -0700 Subject: [PATCH 634/750] nbd: fix memory leak of nbd_dev array We leak the memory allocated for the nbd_dev array at multiple places. Fix them by either adding a kfree() or by rearranging code to return before we allocate the memory. Signed-off-by: Sven Wegener Cc: Paul Clements Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/block/nbd.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-) diff --git a/drivers/block/nbd.c b/drivers/block/nbd.c index ad98dda6037..1778e4a2c67 100644 --- a/drivers/block/nbd.c +++ b/drivers/block/nbd.c @@ -707,15 +707,15 @@ static int __init nbd_init(void) BUILD_BUG_ON(sizeof(struct nbd_request) != 28); - nbd_dev = kcalloc(nbds_max, sizeof(*nbd_dev), GFP_KERNEL); - if (!nbd_dev) - return -ENOMEM; - if (max_part < 0) { printk(KERN_CRIT "nbd: max_part must be >= 0\n"); return -EINVAL; } + nbd_dev = kcalloc(nbds_max, sizeof(*nbd_dev), GFP_KERNEL); + if (!nbd_dev) + return -ENOMEM; + part_shift = 0; if (max_part > 0) part_shift = fls(max_part); @@ -779,6 +779,7 @@ out: blk_cleanup_queue(nbd_dev[i].disk->queue); put_disk(nbd_dev[i].disk); } + kfree(nbd_dev); return err; } @@ -795,6 +796,7 @@ static void __exit nbd_cleanup(void) } } unregister_blkdev(NBD_MAJOR, "nbd"); + kfree(nbd_dev); printk(KERN_INFO "nbd: unregistered device at major %d\n", NBD_MAJOR); } -- GitLab From c82f2966015a2c9708fb8f20694ef7ba8567d2e1 Mon Sep 17 00:00:00 2001 From: Akinobu Mita Date: Wed, 20 Aug 2008 14:09:09 -0700 Subject: [PATCH 635/750] brd: fix name argument of unregister_blkdev() The name of brd block device is "ramdisk", it's not "brd". (The block device is registered by register_blkdev(RAMDISK_MAJOR, "ramdisk") So it should be unregistered by unregister_blkdev(RAMDISK_MAJOR, "ramdisk") Signed-off-by: Akinobu Mita Acked-by: Nick Piggin Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/block/brd.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/block/brd.c b/drivers/block/brd.c index 24b97b0bef9..d070d492e38 100644 --- a/drivers/block/brd.c +++ b/drivers/block/brd.c @@ -571,8 +571,8 @@ out_free: list_del(&brd->brd_list); brd_free(brd); } + unregister_blkdev(RAMDISK_MAJOR, "ramdisk"); - unregister_blkdev(RAMDISK_MAJOR, "brd"); return -ENOMEM; } -- GitLab From ff9bc512f198eb47204f55b24c6fe3d36ed89592 Mon Sep 17 00:00:00 2001 From: Pavel Emelyanov Date: Wed, 20 Aug 2008 14:09:10 -0700 Subject: [PATCH 636/750] binfmt_misc: fix false -ENOEXEC when coupled with other binary handlers In case the binfmt_misc binary handler is registered *before* the e.g. script one (when for example being compiled as a module) the following situation may occur: 1. user launches a script, whose interpreter is a misc binary; 2. the load_misc_binary sets the misc_bang and returns -ENOEVEC, since the binary is a script; 3. the load_script_binary loads one and calls for search_binary_hander to run the interpreter; 4. the load_misc_binary is called again, but refuses to load the binary due to misc_bang bit set. The fix is to move the misc_bang setting lower - prior to the actual call to the search_binary_handler. Caused by the commit 3a2e7f47 (binfmt_misc.c: avoid potential kernel stack overflow) Signed-off-by: Pavel Emelyanov Reported-by: Kirill A. Shutemov Tested-by: Kirill A. Shutemov Cc: [2.6.26.x] Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- fs/binfmt_misc.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/fs/binfmt_misc.c b/fs/binfmt_misc.c index 756205314c2..8d7e88e02e0 100644 --- a/fs/binfmt_misc.c +++ b/fs/binfmt_misc.c @@ -120,8 +120,6 @@ static int load_misc_binary(struct linux_binprm *bprm, struct pt_regs *regs) if (bprm->misc_bang) goto _ret; - bprm->misc_bang = 1; - /* to keep locking time low, we copy the interpreter string */ read_lock(&entries_lock); fmt = check_file(bprm); @@ -199,6 +197,8 @@ static int load_misc_binary(struct linux_binprm *bprm, struct pt_regs *regs) if (retval < 0) goto _error; + bprm->misc_bang = 1; + retval = search_binary_handler (bprm, regs); if (retval < 0) goto _error; -- GitLab From 1d96469a34781340b2cc9bdf97d5913eecdaa038 Mon Sep 17 00:00:00 2001 From: Atsushi Nemoto Date: Wed, 20 Aug 2008 14:09:11 -0700 Subject: [PATCH 637/750] rtc: fix double lock on UIE emulation With commit 5ad31a575157147b43fa84ef1e21471661653878 ("rtc: remove BKL for ioctl()"), RTC_UIE_ON ioctl cause double lock on rtc->ops_lock. The ops_lock must not be held while set_uie() calls rtc_read_time() which takes the lock. Also clear_uie() does not need ops_lock. This patch fixes return value of RTC_UIE_OFF ioctl too. Signed-off-by: Atsushi Nemoto Cc: David Brownell Cc: Russell King Cc: Alessandro Zummo Cc: "Rafael J. Wysocki" Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/rtc/rtc-dev.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/rtc/rtc-dev.c b/drivers/rtc/rtc-dev.c index 35dcc06eb3e..f118252f3a9 100644 --- a/drivers/rtc/rtc-dev.c +++ b/drivers/rtc/rtc-dev.c @@ -403,11 +403,14 @@ static long rtc_dev_ioctl(struct file *file, #ifdef CONFIG_RTC_INTF_DEV_UIE_EMUL case RTC_UIE_OFF: + mutex_unlock(&rtc->ops_lock); clear_uie(rtc); - break; + return 0; case RTC_UIE_ON: + mutex_unlock(&rtc->ops_lock); err = set_uie(rtc); + return err; #endif default: err = -ENOTTY; -- GitLab From 27aa069a8850a36b8aef0160e73cfd928c6bbcc4 Mon Sep 17 00:00:00 2001 From: Krzysztof Helt Date: Wed, 20 Aug 2008 14:09:11 -0700 Subject: [PATCH 638/750] pm2fb: free cmap memory on module remove Release cmap memory allocated in the probe function. Signed-off-by: Krzysztof Helt Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/pm2fb.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/video/pm2fb.c b/drivers/video/pm2fb.c index 3f1ca2adda3..c6dd924976a 100644 --- a/drivers/video/pm2fb.c +++ b/drivers/video/pm2fb.c @@ -1746,6 +1746,7 @@ static void __devexit pm2fb_remove(struct pci_dev *pdev) release_mem_region(fix->mmio_start, fix->mmio_len); pci_set_drvdata(pdev, NULL); + fb_dealloc_cmap(&info->cmap); kfree(info->pixmap.addr); kfree(info); } -- GitLab From a09f48551273ee89d4e9ae37474807dc2da1d757 Mon Sep 17 00:00:00 2001 From: Andrew Morton Date: Wed, 20 Aug 2008 14:09:14 -0700 Subject: [PATCH 639/750] drivers/char/ipmi/ipmi_si_intf.c:default_find_bmc(): fix leak If check_legacy_ioport() returns true, we leak *info. Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11362 Reported-by: Daniel Marjamki Cc: Christian Krafft Cc: Michael Ellerman Cc: Corey Minyard Cc: Paul Mackerras Cc: Benjamin Herrenschmidt Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/char/ipmi/ipmi_si_intf.c | 8 +++----- 1 file changed, 3 insertions(+), 5 deletions(-) diff --git a/drivers/char/ipmi/ipmi_si_intf.c b/drivers/char/ipmi/ipmi_si_intf.c index f52931e1c16..8e8afb6141f 100644 --- a/drivers/char/ipmi/ipmi_si_intf.c +++ b/drivers/char/ipmi/ipmi_si_intf.c @@ -2695,15 +2695,13 @@ static __devinit void default_find_bmc(void) for (i = 0; ; i++) { if (!ipmi_defaults[i].port) break; - - info = kzalloc(sizeof(*info), GFP_KERNEL); - if (!info) - return; - #ifdef CONFIG_PPC_MERGE if (check_legacy_ioport(ipmi_defaults[i].port)) continue; #endif + info = kzalloc(sizeof(*info), GFP_KERNEL); + if (!info) + return; info->addr_source = NULL; -- GitLab From 481ebd0d76b501c5772f702ae31e55350c0858a3 Mon Sep 17 00:00:00 2001 From: Johannes Weiner Date: Wed, 20 Aug 2008 14:09:15 -0700 Subject: [PATCH 640/750] bootmem: fix aligning of node-relative indexes and offsets Absolute alignment requirements may never be applied to node-relative offsets. Andreas Herrmann spotted this flaw when a bootmem allocation on an unaligned node was itself not aligned because the combination of an unaligned node with an aligned offset into that node is not garuanteed to be aligned itself. This patch introduces two helper functions that align a node-relative index or offset with respect to the node's starting address so that the absolute PFN or virtual address that results from combining the two satisfies the requested alignment. Then all the broken ALIGN()s in alloc_bootmem_core() are replaced by these helpers. Signed-off-by: Johannes Weiner Reported-by: Andreas Herrmann Debugged-by: Andreas Herrmann Reviewed-by: Andreas Herrmann Tested-by: Andreas Herrmann Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- mm/bootmem.c | 35 +++++++++++++++++++++++++++++------ 1 file changed, 29 insertions(+), 6 deletions(-) diff --git a/mm/bootmem.c b/mm/bootmem.c index e023c68b025..ad8eec6e44a 100644 --- a/mm/bootmem.c +++ b/mm/bootmem.c @@ -405,6 +405,29 @@ int __init reserve_bootmem(unsigned long addr, unsigned long size, } #endif /* !CONFIG_HAVE_ARCH_BOOTMEM_NODE */ +static unsigned long align_idx(struct bootmem_data *bdata, unsigned long idx, + unsigned long step) +{ + unsigned long base = bdata->node_min_pfn; + + /* + * Align the index with respect to the node start so that the + * combination of both satisfies the requested alignment. + */ + + return ALIGN(base + idx, step) - base; +} + +static unsigned long align_off(struct bootmem_data *bdata, unsigned long off, + unsigned long align) +{ + unsigned long base = PFN_PHYS(bdata->node_min_pfn); + + /* Same as align_idx for byte offsets */ + + return ALIGN(base + off, align) - base; +} + static void * __init alloc_bootmem_core(struct bootmem_data *bdata, unsigned long size, unsigned long align, unsigned long goal, unsigned long limit) @@ -441,7 +464,7 @@ static void * __init alloc_bootmem_core(struct bootmem_data *bdata, else start = ALIGN(min, step); - sidx = start - bdata->node_min_pfn;; + sidx = start - bdata->node_min_pfn; midx = max - bdata->node_min_pfn; if (bdata->hint_idx > sidx) { @@ -450,7 +473,7 @@ static void * __init alloc_bootmem_core(struct bootmem_data *bdata, * catch the fallback below. */ fallback = sidx + 1; - sidx = ALIGN(bdata->hint_idx, step); + sidx = align_idx(bdata, bdata->hint_idx, step); } while (1) { @@ -459,7 +482,7 @@ static void * __init alloc_bootmem_core(struct bootmem_data *bdata, unsigned long eidx, i, start_off, end_off; find_block: sidx = find_next_zero_bit(bdata->node_bootmem_map, midx, sidx); - sidx = ALIGN(sidx, step); + sidx = align_idx(bdata, sidx, step); eidx = sidx + PFN_UP(size); if (sidx >= midx || eidx > midx) @@ -467,7 +490,7 @@ find_block: for (i = sidx; i < eidx; i++) if (test_bit(i, bdata->node_bootmem_map)) { - sidx = ALIGN(i, step); + sidx = align_idx(bdata, i, step); if (sidx == i) sidx += step; goto find_block; @@ -475,7 +498,7 @@ find_block: if (bdata->last_end_off & (PAGE_SIZE - 1) && PFN_DOWN(bdata->last_end_off) + 1 == sidx) - start_off = ALIGN(bdata->last_end_off, align); + start_off = align_off(bdata, bdata->last_end_off, align); else start_off = PFN_PHYS(sidx); @@ -499,7 +522,7 @@ find_block: } if (fallback) { - sidx = ALIGN(fallback - 1, step); + sidx = align_idx(bdata, fallback - 1, step); fallback = 0; goto find_block; } -- GitLab From 141d87e7debe3334018e46859c7565c44cebda65 Mon Sep 17 00:00:00 2001 From: Michael Hennerich Date: Wed, 20 Aug 2008 14:09:16 -0700 Subject: [PATCH 641/750] Video/Framebuffer: add fuctional power management support to Blackfin BF54x LQ043 framebuffer driver Fix bug: does nor properply resume after suspend mem Fix for PM_SUSPEND_MEM: Save and restore peripheral base and DMA registers Signed-off-by: Michael Hennerich Signed-off-by: Bryan Wu Acked-by: Krzysztof Helt Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/bf54x-lq043fb.c | 15 ++++++++++++--- 1 file changed, 12 insertions(+), 3 deletions(-) diff --git a/drivers/video/bf54x-lq043fb.c b/drivers/video/bf54x-lq043fb.c index 940467aed13..6d5aa806777 100644 --- a/drivers/video/bf54x-lq043fb.c +++ b/drivers/video/bf54x-lq043fb.c @@ -733,7 +733,6 @@ static int bfin_bf54x_remove(struct platform_device *pdev) static int bfin_bf54x_suspend(struct platform_device *pdev, pm_message_t state) { struct fb_info *fbinfo = platform_get_drvdata(pdev); - struct bfin_bf54xfb_info *info = fbinfo->par; bfin_write_EPPI0_CONTROL(bfin_read_EPPI0_CONTROL() & ~EPPI_EN); disable_dma(CH_EPPI0); @@ -747,8 +746,18 @@ static int bfin_bf54x_resume(struct platform_device *pdev) struct fb_info *fbinfo = platform_get_drvdata(pdev); struct bfin_bf54xfb_info *info = fbinfo->par; - enable_dma(CH_EPPI0); - bfin_write_EPPI0_CONTROL(bfin_read_EPPI0_CONTROL() | EPPI_EN); + if (info->lq043_open_cnt) { + + bfin_write_EPPI0_CONTROL(0); + SSYNC(); + + config_dma(info); + config_ppi(info); + + /* start dma */ + enable_dma(CH_EPPI0); + bfin_write_EPPI0_CONTROL(bfin_read_EPPI0_CONTROL() | EPPI_EN); + } return 0; } -- GitLab From 2d70b68d42b5196a48ccb639e3797f097ef5bea3 Mon Sep 17 00:00:00 2001 From: Ken Chen Date: Wed, 20 Aug 2008 14:09:17 -0700 Subject: [PATCH 642/750] fix setpriority(PRIO_PGRP) thread iterator breakage When user calls sys_setpriority(PRIO_PGRP ...) on a NPTL style multi-LWP process, only the task leader of the process is affected, all other sibling LWP threads didn't receive the setting. The problem was that the iterator used in sys_setpriority() only iteartes over one task for each process, ignoring all other sibling thread. Introduce a new macro do_each_pid_thread / while_each_pid_thread to walk each thread of a process. Convert 4 call sites in {set/get}priority and ioprio_{set/get}. Signed-off-by: Ken Chen Cc: Oleg Nesterov Cc: Roland McGrath Cc: Ingo Molnar Cc: Thomas Gleixner Cc: Jens Axboe Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- fs/ioprio.c | 8 ++++---- include/linux/pid.h | 9 +++++++++ kernel/sys.c | 8 ++++---- 3 files changed, 17 insertions(+), 8 deletions(-) diff --git a/fs/ioprio.c b/fs/ioprio.c index c4a1c3c65aa..da3cc460d4d 100644 --- a/fs/ioprio.c +++ b/fs/ioprio.c @@ -115,11 +115,11 @@ asmlinkage long sys_ioprio_set(int which, int who, int ioprio) pgrp = task_pgrp(current); else pgrp = find_vpid(who); - do_each_pid_task(pgrp, PIDTYPE_PGID, p) { + do_each_pid_thread(pgrp, PIDTYPE_PGID, p) { ret = set_task_ioprio(p, ioprio); if (ret) break; - } while_each_pid_task(pgrp, PIDTYPE_PGID, p); + } while_each_pid_thread(pgrp, PIDTYPE_PGID, p); break; case IOPRIO_WHO_USER: if (!who) @@ -204,7 +204,7 @@ asmlinkage long sys_ioprio_get(int which, int who) pgrp = task_pgrp(current); else pgrp = find_vpid(who); - do_each_pid_task(pgrp, PIDTYPE_PGID, p) { + do_each_pid_thread(pgrp, PIDTYPE_PGID, p) { tmpio = get_task_ioprio(p); if (tmpio < 0) continue; @@ -212,7 +212,7 @@ asmlinkage long sys_ioprio_get(int which, int who) ret = tmpio; else ret = ioprio_best(ret, tmpio); - } while_each_pid_task(pgrp, PIDTYPE_PGID, p); + } while_each_pid_thread(pgrp, PIDTYPE_PGID, p); break; case IOPRIO_WHO_USER: if (!who) diff --git a/include/linux/pid.h b/include/linux/pid.h index 22921ac4cfd..d7e98ff8021 100644 --- a/include/linux/pid.h +++ b/include/linux/pid.h @@ -161,4 +161,13 @@ pid_t pid_vnr(struct pid *pid); } \ } while (0) +#define do_each_pid_thread(pid, type, task) \ + do_each_pid_task(pid, type, task) { \ + struct task_struct *tg___ = task; \ + do { + +#define while_each_pid_thread(pid, type, task) \ + } while_each_thread(tg___, task); \ + task = tg___; \ + } while_each_pid_task(pid, type, task) #endif /* _LINUX_PID_H */ diff --git a/kernel/sys.c b/kernel/sys.c index 3dacb00a7f7..038a7bc0901 100644 --- a/kernel/sys.c +++ b/kernel/sys.c @@ -169,9 +169,9 @@ asmlinkage long sys_setpriority(int which, int who, int niceval) pgrp = find_vpid(who); else pgrp = task_pgrp(current); - do_each_pid_task(pgrp, PIDTYPE_PGID, p) { + do_each_pid_thread(pgrp, PIDTYPE_PGID, p) { error = set_one_prio(p, niceval, error); - } while_each_pid_task(pgrp, PIDTYPE_PGID, p); + } while_each_pid_thread(pgrp, PIDTYPE_PGID, p); break; case PRIO_USER: user = current->user; @@ -229,11 +229,11 @@ asmlinkage long sys_getpriority(int which, int who) pgrp = find_vpid(who); else pgrp = task_pgrp(current); - do_each_pid_task(pgrp, PIDTYPE_PGID, p) { + do_each_pid_thread(pgrp, PIDTYPE_PGID, p) { niceval = 20 - task_nice(p); if (niceval > retval) retval = niceval; - } while_each_pid_task(pgrp, PIDTYPE_PGID, p); + } while_each_pid_thread(pgrp, PIDTYPE_PGID, p); break; case PRIO_USER: user = current->user; -- GitLab From 479db0bf408e65baa14d2a9821abfcbc0804b847 Mon Sep 17 00:00:00 2001 From: Nick Piggin Date: Wed, 20 Aug 2008 14:09:18 -0700 Subject: [PATCH 643/750] mm: dirty page tracking race fix There is a race with dirty page accounting where a page may not properly be accounted for. clear_page_dirty_for_io() calls page_mkclean; then TestClearPageDirty. page_mkclean walks the rmaps for that page, and for each one it cleans and write protects the pte if it was dirty. It uses page_check_address to find the pte. That function has a shortcut to avoid the ptl if the pte is not present. Unfortunately, the pte can be switched to not-present then back to present by other code while holding the page table lock -- this should not be a signal for page_mkclean to ignore that pte, because it may be dirty. For example, powerpc64's set_pte_at will clear a previously present pte before setting it to the desired value. There may also be other code in core mm or in arch which do similar things. The consequence of the bug is loss of data integrity due to msync, and loss of dirty page accounting accuracy. XIP's __xip_unmap could easily also be unreliable (depending on the exact XIP locking scheme), which can lead to data corruption. Fix this by having an option to always take ptl to check the pte in page_check_address. It's possible to retain this optimization for page_referenced and try_to_unmap. Signed-off-by: Nick Piggin Cc: Jared Hulbert Cc: Carsten Otte Cc: Hugh Dickins Acked-by: Peter Zijlstra Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- include/linux/rmap.h | 2 +- mm/filemap_xip.c | 2 +- mm/rmap.c | 14 +++++++++----- 3 files changed, 11 insertions(+), 7 deletions(-) diff --git a/include/linux/rmap.h b/include/linux/rmap.h index 69407f85e10..fed6f5e0b41 100644 --- a/include/linux/rmap.h +++ b/include/linux/rmap.h @@ -102,7 +102,7 @@ int try_to_unmap(struct page *, int ignore_refs); * Called from mm/filemap_xip.c to unmap empty zero page */ pte_t *page_check_address(struct page *, struct mm_struct *, - unsigned long, spinlock_t **); + unsigned long, spinlock_t **, int); /* * Used by swapoff to help locate where page is expected in vma. diff --git a/mm/filemap_xip.c b/mm/filemap_xip.c index 380ab402d71..8b710ca1324 100644 --- a/mm/filemap_xip.c +++ b/mm/filemap_xip.c @@ -185,7 +185,7 @@ __xip_unmap (struct address_space * mapping, address = vma->vm_start + ((pgoff - vma->vm_pgoff) << PAGE_SHIFT); BUG_ON(address < vma->vm_start || address >= vma->vm_end); - pte = page_check_address(page, mm, address, &ptl); + pte = page_check_address(page, mm, address, &ptl, 1); if (pte) { /* Nuke the page table entry. */ flush_cache_page(vma, address, pte_pfn(*pte)); diff --git a/mm/rmap.c b/mm/rmap.c index 059774712c0..0383acfcb06 100644 --- a/mm/rmap.c +++ b/mm/rmap.c @@ -224,10 +224,14 @@ unsigned long page_address_in_vma(struct page *page, struct vm_area_struct *vma) /* * Check that @page is mapped at @address into @mm. * + * If @sync is false, page_check_address may perform a racy check to avoid + * the page table lock when the pte is not present (helpful when reclaiming + * highly shared pages). + * * On success returns with pte mapped and locked. */ pte_t *page_check_address(struct page *page, struct mm_struct *mm, - unsigned long address, spinlock_t **ptlp) + unsigned long address, spinlock_t **ptlp, int sync) { pgd_t *pgd; pud_t *pud; @@ -249,7 +253,7 @@ pte_t *page_check_address(struct page *page, struct mm_struct *mm, pte = pte_offset_map(pmd, address); /* Make a quick check before getting the lock */ - if (!pte_present(*pte)) { + if (!sync && !pte_present(*pte)) { pte_unmap(pte); return NULL; } @@ -281,7 +285,7 @@ static int page_referenced_one(struct page *page, if (address == -EFAULT) goto out; - pte = page_check_address(page, mm, address, &ptl); + pte = page_check_address(page, mm, address, &ptl, 0); if (!pte) goto out; @@ -450,7 +454,7 @@ static int page_mkclean_one(struct page *page, struct vm_area_struct *vma) if (address == -EFAULT) goto out; - pte = page_check_address(page, mm, address, &ptl); + pte = page_check_address(page, mm, address, &ptl, 1); if (!pte) goto out; @@ -704,7 +708,7 @@ static int try_to_unmap_one(struct page *page, struct vm_area_struct *vma, if (address == -EFAULT) goto out; - pte = page_check_address(page, mm, address, &ptl); + pte = page_check_address(page, mm, address, &ptl, 0); if (!pte) goto out; -- GitLab From 538f8ea6c85232d00bfa5edd9ba85f16c01057c9 Mon Sep 17 00:00:00 2001 From: Nick Piggin Date: Wed, 20 Aug 2008 14:09:20 -0700 Subject: [PATCH 644/750] mm: xip fix fault vs sparse page invalidate race XIP has a race between sparse pages being inserted into page tables, and sparse pages being zapped when its time to put a non-sparse page in. What can happen is that a process can be left with a dangling sparse page in a MAP_SHARED mapping, while the rest of the world sees the non-sparse version. Ie. data corruption. Guard these operations with a seqlock, making fault-in-sparse-pages the slowpath, and try-to-unmap-sparse-pages the fastpath. Signed-off-by: Nick Piggin Cc: Jared Hulbert Acked-by: Carsten Otte Cc: Hugh Dickins Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- mm/filemap_xip.c | 60 +++++++++++++++++++++++++++++++++++++----------- 1 file changed, 46 insertions(+), 14 deletions(-) diff --git a/mm/filemap_xip.c b/mm/filemap_xip.c index 8b710ca1324..5b9ec47ea25 100644 --- a/mm/filemap_xip.c +++ b/mm/filemap_xip.c @@ -15,6 +15,8 @@ #include #include #include +#include +#include #include #include @@ -22,22 +24,18 @@ * We do use our own empty page to avoid interference with other users * of ZERO_PAGE(), such as /dev/zero */ +static DEFINE_MUTEX(xip_sparse_mutex); +static seqcount_t xip_sparse_seq = SEQCNT_ZERO; static struct page *__xip_sparse_page; +/* called under xip_sparse_mutex */ static struct page *xip_sparse_page(void) { if (!__xip_sparse_page) { struct page *page = alloc_page(GFP_HIGHUSER | __GFP_ZERO); - if (page) { - static DEFINE_SPINLOCK(xip_alloc_lock); - spin_lock(&xip_alloc_lock); - if (!__xip_sparse_page) - __xip_sparse_page = page; - else - __free_page(page); - spin_unlock(&xip_alloc_lock); - } + if (page) + __xip_sparse_page = page; } return __xip_sparse_page; } @@ -174,11 +172,16 @@ __xip_unmap (struct address_space * mapping, pte_t pteval; spinlock_t *ptl; struct page *page; + unsigned count; + int locked = 0; + + count = read_seqcount_begin(&xip_sparse_seq); page = __xip_sparse_page; if (!page) return; +retry: spin_lock(&mapping->i_mmap_lock); vma_prio_tree_foreach(vma, &iter, &mapping->i_mmap, pgoff, pgoff) { mm = vma->vm_mm; @@ -198,6 +201,14 @@ __xip_unmap (struct address_space * mapping, } } spin_unlock(&mapping->i_mmap_lock); + + if (locked) { + mutex_unlock(&xip_sparse_mutex); + } else if (read_seqcount_retry(&xip_sparse_seq, count)) { + mutex_lock(&xip_sparse_mutex); + locked = 1; + goto retry; + } } /* @@ -218,7 +229,7 @@ static int xip_file_fault(struct vm_area_struct *vma, struct vm_fault *vmf) int error; /* XXX: are VM_FAULT_ codes OK? */ - +again: size = (i_size_read(inode) + PAGE_CACHE_SIZE - 1) >> PAGE_CACHE_SHIFT; if (vmf->pgoff >= size) return VM_FAULT_SIGBUS; @@ -245,6 +256,7 @@ static int xip_file_fault(struct vm_area_struct *vma, struct vm_fault *vmf) __xip_unmap(mapping, vmf->pgoff); found: + printk("%s insert %lx@%lx\n", current->comm, (unsigned long)vmf->virtual_address, xip_pfn); err = vm_insert_mixed(vma, (unsigned long)vmf->virtual_address, xip_pfn); if (err == -ENOMEM) @@ -252,14 +264,34 @@ found: BUG_ON(err); return VM_FAULT_NOPAGE; } else { + int err, ret = VM_FAULT_OOM; + + mutex_lock(&xip_sparse_mutex); + write_seqcount_begin(&xip_sparse_seq); + error = mapping->a_ops->get_xip_mem(mapping, vmf->pgoff, 0, + &xip_mem, &xip_pfn); + if (unlikely(!error)) { + write_seqcount_end(&xip_sparse_seq); + mutex_unlock(&xip_sparse_mutex); + goto again; + } + if (error != -ENODATA) + goto out; /* not shared and writable, use xip_sparse_page() */ page = xip_sparse_page(); if (!page) - return VM_FAULT_OOM; + goto out; + err = vm_insert_page(vma, (unsigned long)vmf->virtual_address, + page); + if (err == -ENOMEM) + goto out; - page_cache_get(page); - vmf->page = page; - return 0; + ret = VM_FAULT_NOPAGE; +out: + write_seqcount_end(&xip_sparse_seq); + mutex_unlock(&xip_sparse_mutex); + + return ret; } } -- GitLab From 14bac5acfdb6a40be64acc042c6db73f1a68f6a4 Mon Sep 17 00:00:00 2001 From: Nick Piggin Date: Wed, 20 Aug 2008 14:09:20 -0700 Subject: [PATCH 645/750] mm: xip/ext2 fix block allocation race XIP can call into get_xip_mem concurrently with the same file,offset with create=1. This usually maps down to get_block, which expects the page lock to prevent such a situation. This causes ext2 to explode for one reason or another. Serialise those calls for the moment. For common usages today, I suspect get_xip_mem rarely is called to create new blocks. In future as XIP technologies evolve we might need to look at which operations require scalability, and rework the locking to suit. Signed-off-by: Nick Piggin Cc: Jared Hulbert Acked-by: Carsten Otte Cc: Hugh Dickins Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- mm/filemap_xip.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/mm/filemap_xip.c b/mm/filemap_xip.c index 5b9ec47ea25..b5167dfb2f2 100644 --- a/mm/filemap_xip.c +++ b/mm/filemap_xip.c @@ -248,15 +248,16 @@ again: int err; /* maybe shared writable, allocate new block */ + mutex_lock(&xip_sparse_mutex); error = mapping->a_ops->get_xip_mem(mapping, vmf->pgoff, 1, &xip_mem, &xip_pfn); + mutex_unlock(&xip_sparse_mutex); if (error) return VM_FAULT_SIGBUS; /* unmap sparse mappings at pgoff from all other vmas */ __xip_unmap(mapping, vmf->pgoff); found: - printk("%s insert %lx@%lx\n", current->comm, (unsigned long)vmf->virtual_address, xip_pfn); err = vm_insert_mixed(vma, (unsigned long)vmf->virtual_address, xip_pfn); if (err == -ENOMEM) @@ -340,8 +341,10 @@ __xip_file_write(struct file *filp, const char __user *buf, &xip_mem, &xip_pfn); if (status == -ENODATA) { /* we allocate a new page unmap it */ + mutex_lock(&xip_sparse_mutex); status = a_ops->get_xip_mem(mapping, index, 1, &xip_mem, &xip_pfn); + mutex_unlock(&xip_sparse_mutex); if (!status) /* unmap page at pgoff from all other vmas */ __xip_unmap(mapping, index); -- GitLab From b42f931737bea8ca3982449d63ec46410d13e891 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Wed, 20 Aug 2008 14:09:21 -0700 Subject: [PATCH 646/750] rtc: rtc-ds1374: fix 'no irq' case handling On a PowerPC board with ds1374 RTC I'm getting this error while RTC tries to probe: rtc-ds1374 0-0068: unable to request IRQ This happens because I2C probing code (drivers/of/of_i2c.c) is specifying IRQ0 for 'no irq' case, which is correct. The driver handles this incorrectly, though. This patch fixes it. Signed-off-by: Anton Vorontsov Cc: David Brownell Cc: Alessandro Zummo Acked-by: Peter Korsgaard Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/rtc/rtc-ds1374.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/drivers/rtc/rtc-ds1374.c b/drivers/rtc/rtc-ds1374.c index 640acd20fdd..a150418fba7 100644 --- a/drivers/rtc/rtc-ds1374.c +++ b/drivers/rtc/rtc-ds1374.c @@ -173,7 +173,7 @@ static int ds1374_read_alarm(struct device *dev, struct rtc_wkalrm *alarm) int cr, sr; int ret = 0; - if (client->irq < 0) + if (client->irq <= 0) return -EINVAL; mutex_lock(&ds1374->mutex); @@ -212,7 +212,7 @@ static int ds1374_set_alarm(struct device *dev, struct rtc_wkalrm *alarm) int cr; int ret = 0; - if (client->irq < 0) + if (client->irq <= 0) return -EINVAL; ret = ds1374_read_time(dev, &now); @@ -381,7 +381,7 @@ static int ds1374_probe(struct i2c_client *client, if (ret) goto out_free; - if (client->irq >= 0) { + if (client->irq > 0) { ret = request_irq(client->irq, ds1374_irq, 0, "ds1374", client); if (ret) { @@ -401,7 +401,7 @@ static int ds1374_probe(struct i2c_client *client, return 0; out_irq: - if (client->irq >= 0) + if (client->irq > 0) free_irq(client->irq, client); out_free: @@ -414,7 +414,7 @@ static int __devexit ds1374_remove(struct i2c_client *client) { struct ds1374 *ds1374 = i2c_get_clientdata(client); - if (client->irq >= 0) { + if (client->irq > 0) { mutex_lock(&ds1374->mutex); ds1374->exiting = 1; mutex_unlock(&ds1374->mutex); -- GitLab From d847471d063663b9f36927d265c66a270c0cfaab Mon Sep 17 00:00:00 2001 From: Ian Campbell Date: Wed, 20 Aug 2008 14:09:23 -0700 Subject: [PATCH 647/750] fbdefio: add set_page_dirty handler to deferred IO FB Fixes kernel BUG at lib/radix-tree.c:473. Previously the handler was incidentally provided by tmpfs but this was removed with: commit 14fcc23fdc78e9d32372553ccf21758a9bd56fa1 Author: Hugh Dickins Date: Mon Jul 28 15:46:19 2008 -0700 tmpfs: fix kernel BUG in shmem_delete_inode relying on this behaviour was incorrect in any case and the BUG also appeared when the device node was on an ext3 filesystem. v2: override a_ops at open() time rather than mmap() time to minimise races per AKPM's concerns. Signed-off-by: Ian Campbell Cc: Jaya Kumar Cc: Nick Piggin Cc: Peter Zijlstra Cc: Hugh Dickins Cc: Johannes Weiner Cc: Jeremy Fitzhardinge Cc: Kel Modderman Cc: Markus Armbruster Cc: Krzysztof Helt Cc: [14fcc23fd is in 2.6.25.14 and 2.6.26.1] Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/fb_defio.c | 19 +++++++++++++++++++ drivers/video/fbmem.c | 4 ++++ include/linux/fb.h | 3 +++ 3 files changed, 26 insertions(+) diff --git a/drivers/video/fb_defio.c b/drivers/video/fb_defio.c index 59df132cc37..4835bdc4e9f 100644 --- a/drivers/video/fb_defio.c +++ b/drivers/video/fb_defio.c @@ -114,6 +114,17 @@ static struct vm_operations_struct fb_deferred_io_vm_ops = { .page_mkwrite = fb_deferred_io_mkwrite, }; +static int fb_deferred_io_set_page_dirty(struct page *page) +{ + if (!PageDirty(page)) + SetPageDirty(page); + return 0; +} + +static const struct address_space_operations fb_deferred_io_aops = { + .set_page_dirty = fb_deferred_io_set_page_dirty, +}; + static int fb_deferred_io_mmap(struct fb_info *info, struct vm_area_struct *vma) { vma->vm_ops = &fb_deferred_io_vm_ops; @@ -163,6 +174,14 @@ void fb_deferred_io_init(struct fb_info *info) } EXPORT_SYMBOL_GPL(fb_deferred_io_init); +void fb_deferred_io_open(struct fb_info *info, + struct inode *inode, + struct file *file) +{ + file->f_mapping->a_ops = &fb_deferred_io_aops; +} +EXPORT_SYMBOL_GPL(fb_deferred_io_open); + void fb_deferred_io_cleanup(struct fb_info *info) { void *screen_base = (void __force *) info->screen_base; diff --git a/drivers/video/fbmem.c b/drivers/video/fbmem.c index 6b487801eea..98843c2ecf7 100644 --- a/drivers/video/fbmem.c +++ b/drivers/video/fbmem.c @@ -1344,6 +1344,10 @@ fb_open(struct inode *inode, struct file *file) if (res) module_put(info->fbops->owner); } +#ifdef CONFIG_FB_DEFERRED_IO + if (info->fbdefio) + fb_deferred_io_open(info, inode, file); +#endif out: unlock_kernel(); return res; diff --git a/include/linux/fb.h b/include/linux/fb.h index 3b8870e32af..531ccd5f596 100644 --- a/include/linux/fb.h +++ b/include/linux/fb.h @@ -976,6 +976,9 @@ static inline void __fb_pad_aligned_buffer(u8 *dst, u32 d_pitch, /* drivers/video/fb_defio.c */ extern void fb_deferred_io_init(struct fb_info *info); +extern void fb_deferred_io_open(struct fb_info *info, + struct inode *inode, + struct file *file); extern void fb_deferred_io_cleanup(struct fb_info *info); extern int fb_deferred_io_fsync(struct file *file, struct dentry *dentry, int datasync); -- GitLab From 82d63fc9e30687c055b97928942b8893ea65b0bb Mon Sep 17 00:00:00 2001 From: Al Viro Date: Wed, 20 Aug 2008 14:09:24 -0700 Subject: [PATCH 648/750] cramfs: fix named-pipe handling After commit a97c9bf33f4612e2aed6f000f6b1d268b6814f3c (fix cramfs making duplicate entries in inode cache) in kernel 2.6.14, named-pipe on cramfs does not work properly. It seems the commit make all named-pipe on cramfs share their inode (and named-pipe buffer). Make ..._test() refuse to merge inodes with ->i_ino == 1, take inode setup back to get_cramfs_inode() and make ->drop_inode() evict ones with ->i_ino == 1 immediately. Reported-by: Atsushi Nemoto Cc: Al Viro Cc: [2.6.14 and later] Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- fs/cramfs/inode.c | 84 +++++++++++++++++++++-------------------------- 1 file changed, 38 insertions(+), 46 deletions(-) diff --git a/fs/cramfs/inode.c b/fs/cramfs/inode.c index 0c3b618c15b..f40423eb1a1 100644 --- a/fs/cramfs/inode.c +++ b/fs/cramfs/inode.c @@ -43,58 +43,13 @@ static DEFINE_MUTEX(read_mutex); static int cramfs_iget5_test(struct inode *inode, void *opaque) { struct cramfs_inode *cramfs_inode = opaque; - - if (inode->i_ino != CRAMINO(cramfs_inode)) - return 0; /* does not match */ - - if (inode->i_ino != 1) - return 1; - - /* all empty directories, char, block, pipe, and sock, share inode #1 */ - - if ((inode->i_mode != cramfs_inode->mode) || - (inode->i_gid != cramfs_inode->gid) || - (inode->i_uid != cramfs_inode->uid)) - return 0; /* does not match */ - - if ((S_ISCHR(inode->i_mode) || S_ISBLK(inode->i_mode)) && - (inode->i_rdev != old_decode_dev(cramfs_inode->size))) - return 0; /* does not match */ - - return 1; /* matches */ + return inode->i_ino == CRAMINO(cramfs_inode) && inode->i_ino != 1; } static int cramfs_iget5_set(struct inode *inode, void *opaque) { - static struct timespec zerotime; struct cramfs_inode *cramfs_inode = opaque; - inode->i_mode = cramfs_inode->mode; - inode->i_uid = cramfs_inode->uid; - inode->i_size = cramfs_inode->size; - inode->i_blocks = (cramfs_inode->size - 1) / 512 + 1; - inode->i_gid = cramfs_inode->gid; - /* Struct copy intentional */ - inode->i_mtime = inode->i_atime = inode->i_ctime = zerotime; inode->i_ino = CRAMINO(cramfs_inode); - /* inode->i_nlink is left 1 - arguably wrong for directories, - but it's the best we can do without reading the directory - contents. 1 yields the right result in GNU find, even - without -noleaf option. */ - if (S_ISREG(inode->i_mode)) { - inode->i_fop = &generic_ro_fops; - inode->i_data.a_ops = &cramfs_aops; - } else if (S_ISDIR(inode->i_mode)) { - inode->i_op = &cramfs_dir_inode_operations; - inode->i_fop = &cramfs_directory_operations; - } else if (S_ISLNK(inode->i_mode)) { - inode->i_op = &page_symlink_inode_operations; - inode->i_data.a_ops = &cramfs_aops; - } else { - inode->i_size = 0; - inode->i_blocks = 0; - init_special_inode(inode, inode->i_mode, - old_decode_dev(cramfs_inode->size)); - } return 0; } @@ -104,12 +59,48 @@ static struct inode *get_cramfs_inode(struct super_block *sb, struct inode *inode = iget5_locked(sb, CRAMINO(cramfs_inode), cramfs_iget5_test, cramfs_iget5_set, cramfs_inode); + static struct timespec zerotime; + if (inode && (inode->i_state & I_NEW)) { + inode->i_mode = cramfs_inode->mode; + inode->i_uid = cramfs_inode->uid; + inode->i_size = cramfs_inode->size; + inode->i_blocks = (cramfs_inode->size - 1) / 512 + 1; + inode->i_gid = cramfs_inode->gid; + /* Struct copy intentional */ + inode->i_mtime = inode->i_atime = inode->i_ctime = zerotime; + /* inode->i_nlink is left 1 - arguably wrong for directories, + but it's the best we can do without reading the directory + contents. 1 yields the right result in GNU find, even + without -noleaf option. */ + if (S_ISREG(inode->i_mode)) { + inode->i_fop = &generic_ro_fops; + inode->i_data.a_ops = &cramfs_aops; + } else if (S_ISDIR(inode->i_mode)) { + inode->i_op = &cramfs_dir_inode_operations; + inode->i_fop = &cramfs_directory_operations; + } else if (S_ISLNK(inode->i_mode)) { + inode->i_op = &page_symlink_inode_operations; + inode->i_data.a_ops = &cramfs_aops; + } else { + inode->i_size = 0; + inode->i_blocks = 0; + init_special_inode(inode, inode->i_mode, + old_decode_dev(cramfs_inode->size)); + } unlock_new_inode(inode); } return inode; } +static void cramfs_drop_inode(struct inode *inode) +{ + if (inode->i_ino == 1) + generic_delete_inode(inode); + else + generic_drop_inode(inode); +} + /* * We have our own block cache: don't fill up the buffer cache * with the rom-image, because the way the filesystem is set @@ -534,6 +525,7 @@ static const struct super_operations cramfs_ops = { .put_super = cramfs_put_super, .remount_fs = cramfs_remount, .statfs = cramfs_statfs, + .drop_inode = cramfs_drop_inode, }; static int cramfs_get_sb(struct file_system_type *fs_type, -- GitLab From 6a55617ed5d1aa62b850de2cf66f5ede2eef4825 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Wed, 20 Aug 2008 19:35:56 -0700 Subject: [PATCH 649/750] Linux v2.6.27-rc4 --- Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Makefile b/Makefile index 53bf6ec1af9..2e15e0b4483 100644 --- a/Makefile +++ b/Makefile @@ -1,7 +1,7 @@ VERSION = 2 PATCHLEVEL = 6 SUBLEVEL = 27 -EXTRAVERSION = -rc3 +EXTRAVERSION = -rc4 NAME = Rotary Wombat # *DOCUMENTATION* -- GitLab From efc2dead2c82cae31943828f6d977c483942b0eb Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Wed, 20 Aug 2008 12:44:55 +0200 Subject: [PATCH 650/750] sched: enable LB_BIAS by default Yanmin reported a significant regression on his 16-core machine due to: commit 93b75217df39e6d75889cc6f8050343286aff4a5 Author: Peter Zijlstra Date: Fri Jun 27 13:41:33 2008 +0200 Flip back to the old behaviour. Reported-by: "Zhang, Yanmin" Signed-off-by: Peter Zijlstra Signed-off-by: Ingo Molnar --- kernel/sched_features.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/sched_features.h b/kernel/sched_features.h index 862b06bd560..9353ca78154 100644 --- a/kernel/sched_features.h +++ b/kernel/sched_features.h @@ -8,6 +8,6 @@ SCHED_FEAT(SYNC_WAKEUPS, 1) SCHED_FEAT(HRTICK, 1) SCHED_FEAT(DOUBLE_TICK, 0) SCHED_FEAT(ASYM_GRAN, 1) -SCHED_FEAT(LB_BIAS, 0) +SCHED_FEAT(LB_BIAS, 1) SCHED_FEAT(LB_WAKEUP_UPDATE, 1) SCHED_FEAT(ASYM_EFF_LOAD, 1) -- GitLab From 01dcb0443ed89eccf26c2b43f1ea13b368ae740d Mon Sep 17 00:00:00 2001 From: Randy Dunlap Date: Wed, 20 Aug 2008 16:35:19 -0700 Subject: [PATCH 651/750] rcu: fix synchronize_rcu() so that kernel-doc works Fix RCU's synchronize_rcu() so that it looks like a C function, enabling it to be recognized as a function with kernel-doc annotation. Warning(linux-2.6.26-git11//kernel/rcupdate.c:81): No description found for parameter 'synchronize_rcu' Warning(linux-2.6.26-git11//kernel/rcupdate.c:81): No description found for parameter 'call_rcu' [akpm@linux-foundation.org: fix comment] Signed-off-by: Randy Dunlap Signed-off-by: Andrew Morton Signed-off-by: Ingo Molnar --- kernel/rcupdate.c | 1 + 1 file changed, 1 insertion(+) diff --git a/kernel/rcupdate.c b/kernel/rcupdate.c index f14f372cf6f..467d5940f62 100644 --- a/kernel/rcupdate.c +++ b/kernel/rcupdate.c @@ -77,6 +77,7 @@ void wakeme_after_rcu(struct rcu_head *head) * sections are delimited by rcu_read_lock() and rcu_read_unlock(), * and may be nested. */ +void synchronize_rcu(void); /* Makes kernel-doc tools happy */ synchronize_rcu_xxx(synchronize_rcu, call_rcu) EXPORT_SYMBOL_GPL(synchronize_rcu); -- GitLab From 3c4fbe5e01d7e5309be5045e7ae0db20a049e6dc Mon Sep 17 00:00:00 2001 From: Miao Xie Date: Wed, 20 Aug 2008 16:37:38 -0700 Subject: [PATCH 652/750] nohz: fix wrong event handler after online an offlined cpu On the tickless system(CONFIG_NO_HZ=y and CONFIG_HIGH_RES_TIMERS=n), after I made an offlined cpu online, I found this cpu's event handler was tick_handle_periodic, not tick_nohz_handler. After debuging, I found this bug was caused by the wrong tick mode. the tick mode is not changed to NOHZ_MODE_INACTIVE when the cpu is offline. This patch fixes this bug. Signed-off-by: Miao Xie Signed-off-by: Andrew Morton Signed-off-by: Ingo Molnar --- include/linux/tick.h | 5 ++++- kernel/time/tick-sched.c | 6 +++++- 2 files changed, 9 insertions(+), 2 deletions(-) diff --git a/include/linux/tick.h b/include/linux/tick.h index d3c02695dc5..8cf8cfe2cc9 100644 --- a/include/linux/tick.h +++ b/include/linux/tick.h @@ -74,10 +74,13 @@ extern struct tick_device *tick_get_device(int cpu); extern int tick_init_highres(void); extern int tick_program_event(ktime_t expires, int force); extern void tick_setup_sched_timer(void); +# endif + +# if defined CONFIG_NO_HZ || defined CONFIG_HIGH_RES_TIMERS extern void tick_cancel_sched_timer(int cpu); # else static inline void tick_cancel_sched_timer(int cpu) { } -# endif /* HIGHRES */ +# endif # ifdef CONFIG_GENERIC_CLOCKEVENTS_BROADCAST extern struct tick_device *tick_get_broadcast_device(void); diff --git a/kernel/time/tick-sched.c b/kernel/time/tick-sched.c index f5da526424a..7a46bde78c6 100644 --- a/kernel/time/tick-sched.c +++ b/kernel/time/tick-sched.c @@ -643,17 +643,21 @@ void tick_setup_sched_timer(void) ts->nohz_mode = NOHZ_MODE_HIGHRES; #endif } +#endif /* HIGH_RES_TIMERS */ +#if defined CONFIG_NO_HZ || defined CONFIG_HIGH_RES_TIMERS void tick_cancel_sched_timer(int cpu) { struct tick_sched *ts = &per_cpu(tick_cpu_sched, cpu); +# ifdef CONFIG_HIGH_RES_TIMERS if (ts->sched_timer.base) hrtimer_cancel(&ts->sched_timer); +# endif ts->nohz_mode = NOHZ_MODE_INACTIVE; } -#endif /* HIGH_RES_TIMERS */ +#endif /** * Async notification about clocksource changes -- GitLab From 85d577979a8a94a32ca1d828a91c2eb8300bc9f2 Mon Sep 17 00:00:00 2001 From: David Howells Date: Mon, 18 Aug 2008 11:58:17 +0200 Subject: [PATCH 653/750] werror: fix pci calgary Fix an integer comparison always false warning in the PCI Calgary 64 driver. A u8 is being compared to something that's 512 by default, resulting in the following warning: arch/x86/kernel/pci-calgary_64.c:1285: warning: comparison is always false due to limited range of data type This was introduced by patch b34e90b8f0f30151349134f87b5dc6ef75a5218c. Signed-off-by: David Howells Signed-off-by: Ingo Molnar --- arch/x86/kernel/pci-calgary_64.c | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-) diff --git a/arch/x86/kernel/pci-calgary_64.c b/arch/x86/kernel/pci-calgary_64.c index 218d783ed7a..363a74ec7a7 100644 --- a/arch/x86/kernel/pci-calgary_64.c +++ b/arch/x86/kernel/pci-calgary_64.c @@ -1269,13 +1269,15 @@ static inline int __init determine_tce_table_size(u64 ram) static int __init build_detail_arrays(void) { unsigned long ptr; - int i, scal_detail_size, rio_detail_size; + unsigned numnodes, i; + int scal_detail_size, rio_detail_size; - if (rio_table_hdr->num_scal_dev > MAX_NUMNODES){ + numnodes = rio_table_hdr->num_scal_dev; + if (numnodes > MAX_NUMNODES){ printk(KERN_WARNING "Calgary: MAX_NUMNODES too low! Defined as %d, " "but system has %d nodes.\n", - MAX_NUMNODES, rio_table_hdr->num_scal_dev); + MAX_NUMNODES, numnodes); return -ENODEV; } @@ -1296,8 +1298,7 @@ static int __init build_detail_arrays(void) } ptr = ((unsigned long)rio_table_hdr) + 3; - for (i = 0; i < rio_table_hdr->num_scal_dev; - i++, ptr += scal_detail_size) + for (i = 0; i < numnodes; i++, ptr += scal_detail_size) scal_devs[i] = (struct scal_detail *)ptr; for (i = 0; i < rio_table_hdr->num_rio_dev; -- GitLab From 0c072bb452f0cfd4959bc01ff3627d6385255b20 Mon Sep 17 00:00:00 2001 From: Arjan van de Ven Date: Tue, 8 Jul 2008 09:50:22 -0700 Subject: [PATCH 654/750] x86: use WARN() in arch/x86/mm/ioremap.c Use WARN() instead of a printk+WARN_ON() pair; this way the message becomes part of the warning section for better reporting/collection. Signed-off-by: Arjan van de Ven Cc: akpm@linux-foundation.org Signed-off-by: Ingo Molnar --- arch/x86/mm/ioremap.c | 8 +++----- 1 file changed, 3 insertions(+), 5 deletions(-) diff --git a/arch/x86/mm/ioremap.c b/arch/x86/mm/ioremap.c index 6ba6f889c79..d4b6e6a29ae 100644 --- a/arch/x86/mm/ioremap.c +++ b/arch/x86/mm/ioremap.c @@ -553,13 +553,11 @@ static int __init check_early_ioremap_leak(void) { if (!early_ioremap_nested) return 0; - - printk(KERN_WARNING + WARN(1, KERN_WARNING "Debug warning: early ioremap leak of %d areas detected.\n", - early_ioremap_nested); + early_ioremap_nested); printk(KERN_WARNING - "please boot with early_ioremap_debug and report the dmesg.\n"); - WARN_ON(1); + "please boot with early_ioremap_debug and report the dmesg.\n"); return 1; } -- GitLab From bde78a79a6eb015f33aa4660df1b06f5135def20 Mon Sep 17 00:00:00 2001 From: Arjan van de Ven Date: Tue, 8 Jul 2008 09:51:56 -0700 Subject: [PATCH 655/750] x86: use WARN() in arch/x86/kernel Use WARN() instead of a printk+WARN_ON() pair; this way the message becomes part of the warning section for better reporting/collection. This also allowed the folding of some if()'s into the WARN() Signed-off-by: Arjan van de Ven Cc: akpm@linux-foundation.org Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/mtrr/main.c | 5 +---- arch/x86/kernel/pci-calgary_64.c | 3 +-- arch/x86/kernel/tsc_sync.c | 6 ++---- 3 files changed, 4 insertions(+), 10 deletions(-) diff --git a/arch/x86/kernel/cpu/mtrr/main.c b/arch/x86/kernel/cpu/mtrr/main.c index 6f23969c8fa..b117d7f8a56 100644 --- a/arch/x86/kernel/cpu/mtrr/main.c +++ b/arch/x86/kernel/cpu/mtrr/main.c @@ -1496,11 +1496,8 @@ int __init mtrr_trim_uncached_memory(unsigned long end_pfn) /* kvm/qemu doesn't have mtrr set right, don't trim them all */ if (!highest_pfn) { - if (!kvm_para_available()) { - printk(KERN_WARNING + WARN(!kvm_para_available(), KERN_WARNING "WARNING: strange, CPU MTRRs all blank?\n"); - WARN_ON(1); - } return 0; } diff --git a/arch/x86/kernel/pci-calgary_64.c b/arch/x86/kernel/pci-calgary_64.c index 363a74ec7a7..dcdac6c826e 100644 --- a/arch/x86/kernel/pci-calgary_64.c +++ b/arch/x86/kernel/pci-calgary_64.c @@ -343,9 +343,8 @@ static void iommu_free(struct iommu_table *tbl, dma_addr_t dma_addr, /* were we called with bad_dma_address? */ badend = bad_dma_address + (EMERGENCY_PAGES * PAGE_SIZE); if (unlikely((dma_addr >= bad_dma_address) && (dma_addr < badend))) { - printk(KERN_ERR "Calgary: driver tried unmapping bad DMA " + WARN(1, KERN_ERR "Calgary: driver tried unmapping bad DMA " "address 0x%Lx\n", dma_addr); - WARN_ON(1); return; } diff --git a/arch/x86/kernel/tsc_sync.c b/arch/x86/kernel/tsc_sync.c index 0577825cf89..9ffb01c31c4 100644 --- a/arch/x86/kernel/tsc_sync.c +++ b/arch/x86/kernel/tsc_sync.c @@ -88,11 +88,9 @@ static __cpuinit void check_tsc_warp(void) __raw_spin_unlock(&sync_lock); } } - if (!(now-start)) { - printk("Warning: zero tsc calibration delta: %Ld [max: %Ld]\n", + WARN(!(now-start), + "Warning: zero tsc calibration delta: %Ld [max: %Ld]\n", now-start, end-start); - WARN_ON(1); - } } /* -- GitLab From 320dcc30f498e0a8b282b14cf0feed1897ea3b34 Mon Sep 17 00:00:00 2001 From: Peer Chen Date: Wed, 20 Aug 2008 16:43:24 -0700 Subject: [PATCH 656/750] ALSA: hda_intel: enable snoop for nvidia HDA controller Enable the snoop for nvidia hda controller to avoid data coherence issue. Signed-off-by: Peer Chen Signed-off-by: Andrew Morton Signed-off-by: Takashi Iwai --- sound/pci/hda/hda_intel.c | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c index a73d6ca0a90..1c53e337ecb 100644 --- a/sound/pci/hda/hda_intel.c +++ b/sound/pci/hda/hda_intel.c @@ -278,6 +278,9 @@ enum { /* Defines for Nvidia HDA support */ #define NVIDIA_HDA_TRANSREG_ADDR 0x4e #define NVIDIA_HDA_ENABLE_COHBITS 0x0f +#define NVIDIA_HDA_ISTRM_COH 0x4d +#define NVIDIA_HDA_OSTRM_COH 0x4c +#define NVIDIA_HDA_ENABLE_COHBIT 0x01 /* Defines for Intel SCH HDA snoop control */ #define INTEL_SCH_HDA_DEVC 0x78 @@ -900,6 +903,12 @@ static void azx_init_pci(struct azx *chip) update_pci_byte(chip->pci, NVIDIA_HDA_TRANSREG_ADDR, 0x0f, NVIDIA_HDA_ENABLE_COHBITS); + update_pci_byte(chip->pci, + NVIDIA_HDA_ISTRM_COH, + 0x01, NVIDIA_HDA_ENABLE_COHBIT); + update_pci_byte(chip->pci, + NVIDIA_HDA_OSTRM_COH, + 0x01, NVIDIA_HDA_ENABLE_COHBIT); break; case AZX_DRIVER_SCH: pci_read_config_word(chip->pci, INTEL_SCH_HDA_DEVC, &snoop); -- GitLab From 5e739d1752aca4e8f3e794d431503bfca3162df4 Mon Sep 17 00:00:00 2001 From: Vlad Yasevich Date: Thu, 21 Aug 2008 03:34:25 -0700 Subject: [PATCH 657/750] sctp: fix potential panics in the SCTP-AUTH API. All of the SCTP-AUTH socket options could cause a panic if the extension is disabled and the API is envoked. Additionally, there were some additional assumptions that certain pointers would always be valid which may not always be the case. This patch hardens the API and address all of the crash scenarios. Signed-off-by: Vlad Yasevich Signed-off-by: David S. Miller --- net/sctp/endpointola.c | 4 +- net/sctp/socket.c | 85 ++++++++++++++++++++++++++++++++---------- 2 files changed, 67 insertions(+), 22 deletions(-) diff --git a/net/sctp/endpointola.c b/net/sctp/endpointola.c index e39a0cdef18..4c8d9f45ce0 100644 --- a/net/sctp/endpointola.c +++ b/net/sctp/endpointola.c @@ -103,6 +103,7 @@ static struct sctp_endpoint *sctp_endpoint_init(struct sctp_endpoint *ep, /* Initialize the CHUNKS parameter */ auth_chunks->param_hdr.type = SCTP_PARAM_CHUNKS; + auth_chunks->param_hdr.length = htons(sizeof(sctp_paramhdr_t)); /* If the Add-IP functionality is enabled, we must * authenticate, ASCONF and ASCONF-ACK chunks @@ -110,8 +111,7 @@ static struct sctp_endpoint *sctp_endpoint_init(struct sctp_endpoint *ep, if (sctp_addip_enable) { auth_chunks->chunks[0] = SCTP_CID_ASCONF; auth_chunks->chunks[1] = SCTP_CID_ASCONF_ACK; - auth_chunks->param_hdr.length = - htons(sizeof(sctp_paramhdr_t) + 2); + auth_chunks->param_hdr.length += htons(2); } } diff --git a/net/sctp/socket.c b/net/sctp/socket.c index dbb79adf8f3..bb5c9ef1304 100644 --- a/net/sctp/socket.c +++ b/net/sctp/socket.c @@ -3055,6 +3055,9 @@ static int sctp_setsockopt_auth_chunk(struct sock *sk, { struct sctp_authchunk val; + if (!sctp_auth_enable) + return -EACCES; + if (optlen != sizeof(struct sctp_authchunk)) return -EINVAL; if (copy_from_user(&val, optval, optlen)) @@ -3085,6 +3088,9 @@ static int sctp_setsockopt_hmac_ident(struct sock *sk, struct sctp_hmacalgo *hmacs; int err; + if (!sctp_auth_enable) + return -EACCES; + if (optlen < sizeof(struct sctp_hmacalgo)) return -EINVAL; @@ -3123,6 +3129,9 @@ static int sctp_setsockopt_auth_key(struct sock *sk, struct sctp_association *asoc; int ret; + if (!sctp_auth_enable) + return -EACCES; + if (optlen <= sizeof(struct sctp_authkey)) return -EINVAL; @@ -3160,6 +3169,9 @@ static int sctp_setsockopt_active_key(struct sock *sk, struct sctp_authkeyid val; struct sctp_association *asoc; + if (!sctp_auth_enable) + return -EACCES; + if (optlen != sizeof(struct sctp_authkeyid)) return -EINVAL; if (copy_from_user(&val, optval, optlen)) @@ -3185,6 +3197,9 @@ static int sctp_setsockopt_del_key(struct sock *sk, struct sctp_authkeyid val; struct sctp_association *asoc; + if (!sctp_auth_enable) + return -EACCES; + if (optlen != sizeof(struct sctp_authkeyid)) return -EINVAL; if (copy_from_user(&val, optval, optlen)) @@ -5197,19 +5212,29 @@ static int sctp_getsockopt_maxburst(struct sock *sk, int len, static int sctp_getsockopt_hmac_ident(struct sock *sk, int len, char __user *optval, int __user *optlen) { + struct sctp_hmacalgo __user *p = (void __user *)optval; struct sctp_hmac_algo_param *hmacs; - __u16 param_len; + __u16 data_len = 0; + u32 num_idents; + + if (!sctp_auth_enable) + return -EACCES; hmacs = sctp_sk(sk)->ep->auth_hmacs_list; - param_len = ntohs(hmacs->param_hdr.length); + data_len = ntohs(hmacs->param_hdr.length) - sizeof(sctp_paramhdr_t); - if (len < param_len) + if (len < sizeof(struct sctp_hmacalgo) + data_len) return -EINVAL; + + len = sizeof(struct sctp_hmacalgo) + data_len; + num_idents = data_len / sizeof(u16); + if (put_user(len, optlen)) return -EFAULT; - if (copy_to_user(optval, hmacs->hmac_ids, len)) + if (put_user(num_idents, &p->shmac_num_idents)) + return -EFAULT; + if (copy_to_user(p->shmac_idents, hmacs->hmac_ids, data_len)) return -EFAULT; - return 0; } @@ -5219,6 +5244,9 @@ static int sctp_getsockopt_active_key(struct sock *sk, int len, struct sctp_authkeyid val; struct sctp_association *asoc; + if (!sctp_auth_enable) + return -EACCES; + if (len < sizeof(struct sctp_authkeyid)) return -EINVAL; if (copy_from_user(&val, optval, sizeof(struct sctp_authkeyid))) @@ -5233,6 +5261,12 @@ static int sctp_getsockopt_active_key(struct sock *sk, int len, else val.scact_keynumber = sctp_sk(sk)->ep->active_key_id; + len = sizeof(struct sctp_authkeyid); + if (put_user(len, optlen)) + return -EFAULT; + if (copy_to_user(optval, &val, len)) + return -EFAULT; + return 0; } @@ -5243,13 +5277,16 @@ static int sctp_getsockopt_peer_auth_chunks(struct sock *sk, int len, struct sctp_authchunks val; struct sctp_association *asoc; struct sctp_chunks_param *ch; - u32 num_chunks; + u32 num_chunks = 0; char __user *to; - if (len <= sizeof(struct sctp_authchunks)) + if (!sctp_auth_enable) + return -EACCES; + + if (len < sizeof(struct sctp_authchunks)) return -EINVAL; - if (copy_from_user(&val, p, sizeof(struct sctp_authchunks))) + if (copy_from_user(&val, optval, sizeof(struct sctp_authchunks))) return -EFAULT; to = p->gauth_chunks; @@ -5258,20 +5295,21 @@ static int sctp_getsockopt_peer_auth_chunks(struct sock *sk, int len, return -EINVAL; ch = asoc->peer.peer_chunks; + if (!ch) + goto num; /* See if the user provided enough room for all the data */ num_chunks = ntohs(ch->param_hdr.length) - sizeof(sctp_paramhdr_t); if (len < num_chunks) return -EINVAL; - len = num_chunks; - if (put_user(len, optlen)) + if (copy_to_user(to, ch->chunks, num_chunks)) return -EFAULT; +num: + len = sizeof(struct sctp_authchunks) + num_chunks; + if (put_user(len, optlen)) return -EFAULT; if (put_user(num_chunks, &p->gauth_number_of_chunks)) return -EFAULT; - if (copy_to_user(to, ch->chunks, len)) - return -EFAULT; - return 0; } @@ -5282,13 +5320,16 @@ static int sctp_getsockopt_local_auth_chunks(struct sock *sk, int len, struct sctp_authchunks val; struct sctp_association *asoc; struct sctp_chunks_param *ch; - u32 num_chunks; + u32 num_chunks = 0; char __user *to; - if (len <= sizeof(struct sctp_authchunks)) + if (!sctp_auth_enable) + return -EACCES; + + if (len < sizeof(struct sctp_authchunks)) return -EINVAL; - if (copy_from_user(&val, p, sizeof(struct sctp_authchunks))) + if (copy_from_user(&val, optval, sizeof(struct sctp_authchunks))) return -EFAULT; to = p->gauth_chunks; @@ -5301,17 +5342,21 @@ static int sctp_getsockopt_local_auth_chunks(struct sock *sk, int len, else ch = sctp_sk(sk)->ep->auth_chunk_list; + if (!ch) + goto num; + num_chunks = ntohs(ch->param_hdr.length) - sizeof(sctp_paramhdr_t); - if (len < num_chunks) + if (len < sizeof(struct sctp_authchunks) + num_chunks) return -EINVAL; - len = num_chunks; + if (copy_to_user(to, ch->chunks, num_chunks)) + return -EFAULT; +num: + len = sizeof(struct sctp_authchunks) + num_chunks; if (put_user(len, optlen)) return -EFAULT; if (put_user(num_chunks, &p->gauth_number_of_chunks)) return -EFAULT; - if (copy_to_user(to, ch->chunks, len)) - return -EFAULT; return 0; } -- GitLab From 7701e8c59b0e7cbcf21c1bc49d8b8c6db43027a4 Mon Sep 17 00:00:00 2001 From: Marcin Slusarz Date: Wed, 20 Aug 2008 21:07:47 +0200 Subject: [PATCH 658/750] x86, mmiotrace: silence section mismatch warning - leave_uniprocessor WARNING: vmlinux.o(.text+0x180af): Section mismatch in reference from the function leave_uniprocessor() to the function .cpuinit.text:cpu_up() The function leave_uniprocessor() references the function __cpuinit cpu_up(). This is often because leave_uniprocessor lacks a __cpuinit annotation or the annotation of cpu_up is wrong. leave_uniprocessor calls cpu_up only when CONFIG_HOTPLUG_CPU is set, so it can be safely annotated as __ref Signed-off-by: Marcin Slusarz Cc: Pekka Paalanen Signed-off-by: Ingo Molnar Cc: Ingo Molnar Cc: Pekka Paalanen --- arch/x86/mm/mmio-mod.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/arch/x86/mm/mmio-mod.c b/arch/x86/mm/mmio-mod.c index e7397e108be..635b50e8558 100644 --- a/arch/x86/mm/mmio-mod.c +++ b/arch/x86/mm/mmio-mod.c @@ -430,7 +430,9 @@ static void enter_uniprocessor(void) "may miss events.\n"); } -static void leave_uniprocessor(void) +/* __ref because leave_uniprocessor calls cpu_up which is __cpuinit, + but this whole function is ifdefed CONFIG_HOTPLUG_CPU */ +static void __ref leave_uniprocessor(void) { int cpu; int err; -- GitLab From 7946612de2087e163308e26034286fc2dc9dacf1 Mon Sep 17 00:00:00 2001 From: Jeremy Fitzhardinge Date: Wed, 20 Aug 2008 11:31:07 -0700 Subject: [PATCH 659/750] x86: export pv_lock_ops non-GPL None of the spinlock API is exported GPL, so there's no reason for pv_lock_ops to be. Signed-off-by: Jeremy Fitzhardinge Signed-off-by: Ingo Molnar Cc: drago01 --- arch/x86/kernel/paravirt.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/paravirt.c b/arch/x86/kernel/paravirt.c index 94da4d52d79..300da17e61c 100644 --- a/arch/x86/kernel/paravirt.c +++ b/arch/x86/kernel/paravirt.c @@ -471,7 +471,7 @@ struct pv_lock_ops pv_lock_ops = { .spin_unlock = __ticket_spin_unlock, #endif }; -EXPORT_SYMBOL_GPL(pv_lock_ops); +EXPORT_SYMBOL(pv_lock_ops); EXPORT_SYMBOL_GPL(pv_time_ops); EXPORT_SYMBOL (pv_cpu_ops); -- GitLab From b2a6a58ca6a3ddf4e278a53199c5b8fd39adbc0e Mon Sep 17 00:00:00 2001 From: Vegard Nossum Date: Wed, 20 Aug 2008 18:18:26 +0200 Subject: [PATCH 660/750] x86: fix BUG: unable to handle kernel paging request (numaq_tsc_disable) This section mismatch: >> Seems to be a section mismatch; init_intel() is __cpuinit while >> numaq_tsc_disable() is __init. Seems to be introduced in: >> >> commit 64898a8bad8c94ad7a4bd5cc86b66edfbb081f4a >> Author: Yinghai Lu >> Date: Sat Jul 19 18:01:16 2008 -0700 >> >> x86: extend and use x86_quirks to clean up NUMAQ code > > Oops, I am wrong about numaq_tsc_disable() being __init. Still, I > believe that Yinghai might be able to say what's really wrong :-) Would lead to this crash: BUG: unable to handle kernel paging request at c08a45f0 IP: [] numaq_tsc_disable+0x0/0x40 Fixed by the patch below. Signed-off-by: Vegard Nossum Signed-off-by: Ingo Molnar --- arch/x86/kernel/numaq_32.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/numaq_32.c b/arch/x86/kernel/numaq_32.c index b8c45610b20..eecc8c18f01 100644 --- a/arch/x86/kernel/numaq_32.c +++ b/arch/x86/kernel/numaq_32.c @@ -73,7 +73,7 @@ static void __init smp_dump_qct(void) } -void __init numaq_tsc_disable(void) +void __cpuinit numaq_tsc_disable(void) { if (!found_numaq) return; -- GitLab From c15238df3b65e34fadb1021b0fb0d5aebc7c42c6 Mon Sep 17 00:00:00 2001 From: "venkatesh.pallipadi@intel.com" Date: Wed, 20 Aug 2008 16:45:51 -0700 Subject: [PATCH 661/750] x86: PAT proper tracking of set_memory_uc and friends Big thinko in pat memtype tracking code. reserve_memtype should be called with physical address and not virtual address. Signed-off-by: Venkatesh Pallipadi Signed-off-by: Suresh Siddha Signed-off-by: Ingo Molnar --- arch/x86/mm/pageattr.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/x86/mm/pageattr.c b/arch/x86/mm/pageattr.c index f5f5154ea11..43e2f8483e4 100644 --- a/arch/x86/mm/pageattr.c +++ b/arch/x86/mm/pageattr.c @@ -849,7 +849,7 @@ int set_memory_uc(unsigned long addr, int numpages) /* * for now UC MINUS. see comments in ioremap_nocache() */ - if (reserve_memtype(addr, addr + numpages * PAGE_SIZE, + if (reserve_memtype(__pa(addr), __pa(addr) + numpages * PAGE_SIZE, _PAGE_CACHE_UC_MINUS, NULL)) return -EINVAL; @@ -868,7 +868,7 @@ int set_memory_wc(unsigned long addr, int numpages) if (!pat_enabled) return set_memory_uc(addr, numpages); - if (reserve_memtype(addr, addr + numpages * PAGE_SIZE, + if (reserve_memtype(__pa(addr), __pa(addr) + numpages * PAGE_SIZE, _PAGE_CACHE_WC, NULL)) return -EINVAL; @@ -884,7 +884,7 @@ int _set_memory_wb(unsigned long addr, int numpages) int set_memory_wb(unsigned long addr, int numpages) { - free_memtype(addr, addr + numpages * PAGE_SIZE); + free_memtype(__pa(addr), __pa(addr) + numpages * PAGE_SIZE); return _set_memory_wb(addr, numpages); } -- GitLab From 28df82ebab79c6a2b4295dd94fd8de88196a49df Mon Sep 17 00:00:00 2001 From: "venkatesh.pallipadi@intel.com" Date: Wed, 20 Aug 2008 16:45:52 -0700 Subject: [PATCH 662/750] devmem, x86: PAT Change /dev/mem mmap with O_SYNC to use UC_MINUS All kernel mappings like ioremap(), etc uses UC_MINUS as the type. /dev/mem mappings with /dev/mem being opened with O_SYNC however was using UC, resulting in a conflict with /dev/mem mmap failing. This seems to be affecting some apps (one being flashrom) which are using O_SYNC and which were working before. Switch /dev/mem with O_SYNC also to UC_MINUS. Signed-off-by: Venkatesh Pallipadi Signed-off-by: Ingo Molnar --- arch/x86/mm/pat.c | 17 +++++------------ 1 file changed, 5 insertions(+), 12 deletions(-) diff --git a/arch/x86/mm/pat.c b/arch/x86/mm/pat.c index bb6e8a267bf..2a50e0fa64a 100644 --- a/arch/x86/mm/pat.c +++ b/arch/x86/mm/pat.c @@ -390,14 +390,6 @@ int free_memtype(u64 start, u64 end) } -/* - * /dev/mem mmap interface. The memtype used for mapping varies: - * - Use UC for mappings with O_SYNC flag - * - Without O_SYNC flag, if there is any conflict in reserve_memtype, - * inherit the memtype from existing mapping. - * - Else use UC_MINUS memtype (for backward compatibility with existing - * X drivers. - */ pgprot_t phys_mem_access_prot(struct file *file, unsigned long pfn, unsigned long size, pgprot_t vma_prot) { @@ -435,14 +427,14 @@ int phys_mem_access_prot_allowed(struct file *file, unsigned long pfn, unsigned long size, pgprot_t *vma_prot) { u64 offset = ((u64) pfn) << PAGE_SHIFT; - unsigned long flags = _PAGE_CACHE_UC_MINUS; + unsigned long flags = -1; int retval; if (!range_is_allowed(pfn, size)) return 0; if (file->f_flags & O_SYNC) { - flags = _PAGE_CACHE_UC; + flags = _PAGE_CACHE_UC_MINUS; } #ifdef CONFIG_X86_32 @@ -465,13 +457,14 @@ int phys_mem_access_prot_allowed(struct file *file, unsigned long pfn, #endif /* - * With O_SYNC, we can only take UC mapping. Fail if we cannot. + * With O_SYNC, we can only take UC_MINUS mapping. Fail if we cannot. + * * Without O_SYNC, we want to get * - WB for WB-able memory and no other conflicting mappings * - UC_MINUS for non-WB-able memory with no other conflicting mappings * - Inherit from confliting mappings otherwise */ - if (flags != _PAGE_CACHE_UC_MINUS) { + if (flags != -1) { retval = reserve_memtype(offset, offset + size, flags, NULL); } else { retval = reserve_memtype(offset, offset + size, -1, &flags); -- GitLab From 8323444b5dba3fe55e56a95d20d8f55c1d6745af Mon Sep 17 00:00:00 2001 From: "venkatesh.pallipadi@intel.com" Date: Wed, 20 Aug 2008 16:45:53 -0700 Subject: [PATCH 663/750] x86: PAT Update validate_pat_support for intel CPUs Pentium III and Core Solo/Duo CPUs have an erratum " Page with PAT set to WC while associated MTRR is UC may consolidate to UC " which can result in WC setting in PAT to be ineffective. We will disable PAT on such CPUs, so that we can continue to use MTRR WC setting. Signed-off-by: Venkatesh Pallipadi Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/addon_cpuid_features.c | 17 +++++++++++++++-- 1 file changed, 15 insertions(+), 2 deletions(-) diff --git a/arch/x86/kernel/cpu/addon_cpuid_features.c b/arch/x86/kernel/cpu/addon_cpuid_features.c index 84a8220a607..a6ef672adbb 100644 --- a/arch/x86/kernel/cpu/addon_cpuid_features.c +++ b/arch/x86/kernel/cpu/addon_cpuid_features.c @@ -56,9 +56,22 @@ void __cpuinit validate_pat_support(struct cpuinfo_x86 *c) switch (c->x86_vendor) { case X86_VENDOR_INTEL: - if (c->x86 == 0xF || (c->x86 == 6 && c->x86_model >= 15)) + /* + * There is a known erratum on Pentium III and Core Solo + * and Core Duo CPUs. + * " Page with PAT set to WC while associated MTRR is UC + * may consolidate to UC " + * Because of this erratum, it is better to stick with + * setting WC in MTRR rather than using PAT on these CPUs. + * + * Enable PAT WC only on P4, Core 2 or later CPUs. + */ + if (c->x86 > 0x6 || (c->x86 == 6 && c->x86_model >= 15)) return; - break; + + pat_disable("PAT WC disabled due to known CPU erratum."); + return; + case X86_VENDOR_AMD: case X86_VENDOR_CENTAUR: case X86_VENDOR_TRANSMETA: -- GitLab From 2540e0511ea17e25831be543cdf9381e6209950d Mon Sep 17 00:00:00 2001 From: Jarek Poplawski Date: Thu, 21 Aug 2008 05:11:14 -0700 Subject: [PATCH 664/750] pkt_sched: Fix qdisc_watchdog() vs. dev_deactivate() race dev_deactivate() can skip rescheduling of a qdisc by qdisc_watchdog() or other timer calling netif_schedule() after dev_queue_deactivate(). We prevent this checking aliveness before scheduling the timer. Since during deactivation the root qdisc is available only as qdisc_sleeping additional accessor qdisc_root_sleeping() is created. With feedback from Herbert Xu Signed-off-by: Jarek Poplawski Signed-off-by: David S. Miller --- include/net/sch_generic.h | 5 +++++ net/sched/sch_api.c | 4 ++++ net/sched/sch_cbq.c | 4 ++++ 3 files changed, 13 insertions(+) diff --git a/include/net/sch_generic.h b/include/net/sch_generic.h index 84d25f2e618..b1d2cfea89c 100644 --- a/include/net/sch_generic.h +++ b/include/net/sch_generic.h @@ -193,6 +193,11 @@ static inline struct Qdisc *qdisc_root(struct Qdisc *qdisc) return qdisc->dev_queue->qdisc; } +static inline struct Qdisc *qdisc_root_sleeping(struct Qdisc *qdisc) +{ + return qdisc->dev_queue->qdisc_sleeping; +} + /* The qdisc root lock is a mechanism by which to top level * of a qdisc tree can be locked from any qdisc node in the * forest. This allows changing the configuration of some diff --git a/net/sched/sch_api.c b/net/sched/sch_api.c index ef0efeca635..45f442d7de4 100644 --- a/net/sched/sch_api.c +++ b/net/sched/sch_api.c @@ -444,6 +444,10 @@ void qdisc_watchdog_schedule(struct qdisc_watchdog *wd, psched_time_t expires) { ktime_t time; + if (test_bit(__QDISC_STATE_DEACTIVATED, + &qdisc_root_sleeping(wd->qdisc)->state)) + return; + wd->qdisc->flags |= TCQ_F_THROTTLED; time = ktime_set(0, 0); time = ktime_add_ns(time, PSCHED_US2NS(expires)); diff --git a/net/sched/sch_cbq.c b/net/sched/sch_cbq.c index 47ef492c4ff..8fa90d68ec6 100644 --- a/net/sched/sch_cbq.c +++ b/net/sched/sch_cbq.c @@ -521,6 +521,10 @@ static void cbq_ovl_delay(struct cbq_class *cl) struct cbq_sched_data *q = qdisc_priv(cl->qdisc); psched_tdiff_t delay = cl->undertime - q->now; + if (test_bit(__QDISC_STATE_DEACTIVATED, + &qdisc_root_sleeping(cl->qdisc)->state)) + return; + if (!cl->delayed) { psched_time_t sched = q->now; ktime_t expires; -- GitLab From 25fdeb3f4468595ab2885687b13515fa848731c2 Mon Sep 17 00:00:00 2001 From: Ingo Oeser Date: Wed, 23 Jul 2008 01:25:01 +0200 Subject: [PATCH 665/750] kobject: Replace ALL occurrences of '/' with '!' instead of only the first one. A recent patch from Kay Sievers replaced the first occurrence of '/' with '!' as needed for block devices. Now do some cheap defensive coding and replace all of them to avoid future issues in this area. Signed-off-by: Ingo Oeser Cc: Kay Sievers Signed-off-by: Greg Kroah-Hartman --- lib/kobject.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/lib/kobject.c b/lib/kobject.c index bd732ffebc8..fbf0ae28237 100644 --- a/lib/kobject.c +++ b/lib/kobject.c @@ -223,8 +223,7 @@ static int kobject_set_name_vargs(struct kobject *kobj, const char *fmt, return -ENOMEM; /* ewww... some of these buggers have '/' in the name ... */ - s = strchr(kobj->name, '/'); - if (s) + while ((s = strchr(kobj->name, '/'))) s[0] = '!'; kfree(old_name); -- GitLab From 95e0a8778ebf53b745763032485d2c96f47ed39b Mon Sep 17 00:00:00 2001 From: Takenori Nagano Date: Tue, 15 Jul 2008 17:49:42 +0900 Subject: [PATCH 666/750] Japanese translation of Documentation/SubmitChecklist Hi, This patch adds SubmitChecklist translated into Japanese to Documentation/ja_JP directory. The translated SubmitChecklist has already been reviewed by JF project. SubmitChecklist is one of the important policy documents. So, I would like to merge into 2.6.27. Signed-off-by: Takenori Nagano Signed-off-by: Greg Kroah-Hartman --- Documentation/ja_JP/SubmitChecklist | 111 ++++++++++++++++++++++++++++ 1 file changed, 111 insertions(+) create mode 100644 Documentation/ja_JP/SubmitChecklist diff --git a/Documentation/ja_JP/SubmitChecklist b/Documentation/ja_JP/SubmitChecklist new file mode 100644 index 00000000000..6c42e071d72 --- /dev/null +++ b/Documentation/ja_JP/SubmitChecklist @@ -0,0 +1,111 @@ +NOTE: +This is a version of Documentation/SubmitChecklist into Japanese. +This document is maintained by Takenori Nagano +and the JF Project team . +If you find any difference between this document and the original file +or a problem with the translation, +please contact the maintainer of this file or JF project. + +Please also note that the purpose of this file is to be easier to read +for non English (read: Japanese) speakers and is not intended as a +fork. So if you have any comments or updates of this file, please try +to update the original English file first. + +Last Updated: 2008/07/14 +================================== +これは、 +linux-2.6.26/Documentation/SubmitChecklist の和訳です。 + +翻訳団体： JF プロジェクト < http://www.linux.or.jp/JF/ > +翻訳日： 2008/07/14 +翻訳者： Takenori Nagano +校正者： Masanori Kobayashi さん +================================== + + +Linux カーネルパッチ投稿者向けチェックリスト +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +本書では、パッチをより素早く取り込んでもらいたい開発者が実践すべき基本的な事柄 +をいくつか紹介します。ここにある全ての事柄は、Documentation/SubmittingPatches +などのLinuxカーネルパッチ投稿に際しての心得を補足するものです。 + + 1: 妥当なCONFIGオプションや変更されたCONFIGオプション、つまり =y, =m, =n + 全てで正しくビルドできることを確認してください。その際、gcc及びリンカが + warningやerrorを出していないことも確認してください。 + + 2: allnoconfig, allmodconfig オプションを用いて正しくビルドできることを + 確認してください。 + + 3: 手許のクロスコンパイルツールやOSDLのPLMのようなものを用いて、複数の + アーキテクチャにおいても正しくビルドできることを確認してください。 + + 4: 64bit長の'unsigned long'を使用しているppc64は、クロスコンパイルでの + チェックに適当なアーキテクチャです。 + + 5: カーネルコーディングスタイルに準拠しているかどうか確認してください(!) + + 6: CONFIGオプションの追加・変更をした場合には、CONFIGメニューが壊れていない + ことを確認してください。 + + 7: 新しくKconfigのオプションを追加する際には、必ずそのhelpも記述してください。 + + 8: 適切なKconfigの依存関係を考えながら慎重にチェックしてください。 + ただし、この作業はマシンを使ったテストできちんと行うのがとても困難です。 + うまくやるには、自分の頭で考えることです。 + + 9: sparseを利用してちゃんとしたコードチェックをしてください。 + +10: 'make checkstack' と 'make namespacecheck' を利用し、問題が発見されたら + 修正してください。'make checkstack' は明示的に問題を示しませんが、どれか + １つの関数が512バイトより大きいスタックを使っていれば、修正すべき候補と + なります。 + +11: グローバルなkernel API を説明する kernel-doc をソースの中に含めてください。 + ( staticな関数においては必須ではありませんが、含めてもらっても結構です ) + そして、'make htmldocs' もしくは 'make mandocs' を利用して追記した + ドキュメントのチェックを行い、問題が見つかった場合には修正を行ってください。 + +12: CONFIG_PREEMPT, CONFIG_DEBUG_PREEMPT, CONFIG_DEBUG_SLAB, + CONFIG_DEBUG_PAGEALLOC, CONFIG_DEBUG_MUTEXES, CONFIG_DEBUG_SPINLOCK, + CONFIG_DEBUG_SPINLOCK_SLEEP これら全てを同時に有効にして動作確認を + 行ってください。 + +13: CONFIG_SMP, CONFIG_PREEMPT を有効にした場合と無効にした場合の両方で + ビルドした上、動作確認を行ってください。 + +14: もしパッチがディスクのI/O性能などに影響を与えるようであれば、 + 'CONFIG_LBD'オプションを有効にした場合と無効にした場合の両方で + テストを実施してみてください。 + +15: lockdepの機能を全て有効にした上で、全てのコードパスを評価してください。 + +16: /proc に新しいエントリを追加した場合には、Documentation/ 配下に + 必ずドキュメントを追加してください。 + +17: 新しいブートパラメータを追加した場合には、 + 必ずDocumentation/kernel-parameters.txt に説明を追加してください。 + +18: 新しくmoduleにパラメータを追加した場合には、MODULE_PARM_DESC()を + 利用して必ずその説明を記述してください。 + +19: 新しいuserspaceインタフェースを作成した場合には、Documentation/ABI/ に + Documentation/ABI/README を参考にして必ずドキュメントを追加してください。 + +20: 'make headers_check'を実行して全く問題がないことを確認してください。 + +21: 少なくともslabアロケーションとpageアロケーションに失敗した場合の + 挙動について、fault-injectionを利用して確認してください。 + Documentation/fault-injection/ を参照してください。 + + 追加したコードがかなりの量であったならば、サブシステム特有の + fault-injectionを追加したほうが良いかもしれません。 + +22: 新たに追加したコードは、`gcc -W'でコンパイルしてください。 + このオプションは大量の不要なメッセージを出力しますが、 + "warning: comparison between signed and unsigned" のようなメッセージは、 + バグを見つけるのに役に立ちます。 + +23: 投稿したパッチが -mm パッチセットにマージされた後、全ての既存のパッチや + VM, VFS およびその他のサブシステムに関する様々な変更と、現時点でも共存 + できることを確認するテストを行ってください。 -- GitLab From ac60fc218caacba5ae3bc70cc835cb9f16794d89 Mon Sep 17 00:00:00 2001 From: Tsugikazu Shibata Date: Thu, 21 Aug 2008 11:42:39 +0900 Subject: [PATCH 667/750] Documentation: HOWTO-ja_JP-sync patch Here is a patch for Documentation/ja_JP/HOWTO sync with latest Documentation/HOWTO. It includes translation of changes done by Jon Corbet,Jiri Pirko and me: http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=history;f=Documentation/HOWTO;h=c2371c5a98f99b5eaa785bd0affd6c40187e84e3;hb=HEAD Singed-off-by: Tsugikazu Shibata Signed-off-by: Greg Kroah-Hartman --- Documentation/ja_JP/HOWTO | 67 +++++++++++++++++++++++++++------------ 1 file changed, 47 insertions(+), 20 deletions(-) diff --git a/Documentation/ja_JP/HOWTO b/Documentation/ja_JP/HOWTO index 488c77fa3aa..0775cf4798b 100644 --- a/Documentation/ja_JP/HOWTO +++ b/Documentation/ja_JP/HOWTO @@ -11,14 +11,14 @@ for non English (read: Japanese) speakers and is not intended as a fork. So if you have any comments or updates for this file, please try to update the original English file first. -Last Updated: 2007/11/16 +Last Updated: 2008/08/21 ================================== これは、 -linux-2.6.24/Documentation/HOWTO +linux-2.6.27/Documentation/HOWTO の和訳です。 翻訳団体： JF プロジェクト < http://www.linux.or.jp/JF/ > -翻訳日： 2007/11/10 +翻訳日： 2008/8/5 翻訳者： Tsugikazu Shibata 校正者： 松倉さん 小林 雅典さん (Masanori Kobayasi) @@ -287,13 +287,15 @@ Linux カーネルの開発プロセスは現在幾つかの異なるメイン に安定した状態にあると判断したときにリリースされます。目標は毎週新 しい -rc カーネルをリリースすることです。 - - 以下の URL で各 -rc リリースに存在する既知の後戻り問題のリスト - が追跡されます- - http://kernelnewbies.org/known_regressions - - このプロセスはカーネルが 「準備ができた」と考えられるまで継続しま す。このプロセスはだいたい 6週間継続します。 + - 各リリースでの既知の後戻り問題(regression: このリリースの中で新規 + に作り込まれた問題を指す) はその都度 Linux-kernel メーリングリスト + に投稿されます。ゴールとしては、カーネルが 「準備ができた」と宣言 + する前にこのリストの長さをゼロに減らすことですが、現実には、数個の + 後戻り問題がリリース時にたびたび残ってしまいます。 + Andrew Morton が Linux-kernel メーリングリストにカーネルリリースについ て書いたことをここで言っておくことは価値があります- 「カーネルがいつリリースされるかは誰も知りません。なぜなら、これは現 @@ -303,18 +305,20 @@ Andrew Morton が Linux-kernel メーリングリストにカーネルリリー 2.6.x.y -stable カーネルツリー --------------------------- -バージョンに4つ目の数字がついたカーネルは -stable カーネルです。これに -は、2.6.x カーネルで見つかったセキュリティ問題や重大な後戻りに対する比 -較的小さい重要な修正が含まれます。 +バージョン番号が4つの数字に分かれているカーネルは -stable カーネルです。 +これには、2.6.x カーネルで見つかったセキュリティ問題や重大な後戻りに対 +する比較的小さい重要な修正が含まれます。 これは、開発/実験的バージョンのテストに協力することに興味が無く、 最新の安定したカーネルを使いたいユーザに推奨するブランチです。 -もし、2.6.x.y カーネルが存在しない場合には、番号が一番大きい 2.6.x -が最新の安定版カーネルです。 +もし、2.6.x.y カーネルが存在しない場合には、番号が一番大きい 2.6.x が +最新の安定版カーネルです。 -2.6.x.y は "stable" チーム でメンテされており、だ -いたい隔週でリリースされています。 +2.6.x.y は "stable" チーム でメンテされており、必 +要に応じてリリースされます。通常のリリース期間は 2週間毎ですが、差し迫っ +た問題がなければもう少し長くなることもあります。セキュリティ関連の問題 +の場合はこれに対してだいたいの場合、すぐにリリースがされます。 カーネルツリーに入っている、Documentation/stable_kernel_rules.txt ファ イルにはどのような種類の変更が -stable ツリーに受け入れ可能か、またリ @@ -341,7 +345,9 @@ linux-kernel メーリングリストで収集された多数のパッチと同 メインラインへ入れるように Linus にプッシュします。 メインカーネルツリーに含めるために Linus に送る前に、すべての新しいパッ -チが -mm ツリーでテストされることが強く推奨されます。 +チが -mm ツリーでテストされることが強く推奨されています。マージウィン +ドウが開く前に -mm ツリーに現れなかったパッチはメインラインにマージさ +れることは困難になります。 これらのカーネルは安定して動作すべきシステムとして使うのには適切ではあ りませんし、カーネルブランチの中でももっとも動作にリスクが高いものです。 @@ -395,13 +401,15 @@ linux-kernel メーリングリストで収集された多数のパッチと同 - pcmcia, Dominik Brodowski git.kernel.org:/pub/scm/linux/kernel/git/brodo/pcmcia-2.6.git - - SCSI, James Bottomley + - SCSI, James Bottomley git.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6.git + - x86, Ingo Molnar + git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86.git + quilt ツリー- - - USB, PCI ドライバコアと I2C, Greg Kroah-Hartman + - USB, ドライバコアと I2C, Greg Kroah-Hartman kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/ - - x86-64 と i386 の仲間 Andi Kleen その他のカーネルツリーは http://git.kernel.org/ と MAINTAINERS ファ イルに一覧表があります。 @@ -412,13 +420,32 @@ linux-kernel メーリングリストで収集された多数のパッチと同 bugzilla.kernel.org は Linux カーネル開発者がカーネルのバグを追跡する 場所です。ユーザは見つけたバグの全てをこのツールで報告すべきです。 どう kernel bugzilla を使うかの詳細は、以下を参照してください- - http://test.kernel.org/bugzilla/faq.html - + http://bugzilla.kernel.org/page.cgi?id=faq.html メインカーネルソースディレクトリにあるファイル REPORTING-BUGS はカーネ ルバグらしいものについてどうレポートするかの良いテンプレートであり、問 題の追跡を助けるためにカーネル開発者にとってどんな情報が必要なのかの詳 細が書かれています。 +バグレポートの管理 +------------------- + +あなたのハッキングのスキルを訓練する最高の方法のひとつに、他人がレポー +トしたバグを修正することがあります。あなたがカーネルをより安定化させる +こに寄与するということだけでなく、あなたは 現実の問題を修正することを +学び、自分のスキルも強化でき、また他の開発者があなたの存在に気がつき +ます。バグを修正することは、多くの開発者の中から自分が功績をあげる最善 +の道です、なぜなら多くの人は他人のバグの修正に時間を浪費することを好ま +ないからです。 + +すでにレポートされたバグのために仕事をするためには、 +http://bugzilla.kernel.org に行ってください。もし今後のバグレポートに +ついてアドバイスを受けたいのであれば、bugme-new メーリングリスト(新し +いバグレポートだけがここにメールされる) または bugme-janitor メーリン +グリスト(bugzilla の変更毎にここにメールされる)を購読できます。 + + http://lists.linux-foundation.org/mailman/listinfo/bugme-new + http://lists.linux-foundation.org/mailman/listinfo/bugme-janitors + メーリングリスト ------------- -- GitLab From 26d02d1db7d84729b1e49789341e69a493c60ceb Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 30 Jul 2008 12:29:20 -0700 Subject: [PATCH 668/750] drivers/base/driver.c: remove unused to_dev() macro Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman --- drivers/base/driver.c | 3 --- 1 file changed, 3 deletions(-) diff --git a/drivers/base/driver.c b/drivers/base/driver.c index 2ef5acf4368..1e2bda780e4 100644 --- a/drivers/base/driver.c +++ b/drivers/base/driver.c @@ -16,9 +16,6 @@ #include #include "base.h" -#define to_dev(node) container_of(node, struct device, driver_list) - - static struct device *next_device(struct klist_iter *i) { struct klist_node *n = klist_next(i); -- GitLab From bf9ca69fc8d19d4034391d3df4c35dccdef9d28c Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Wed, 30 Jul 2008 12:29:21 -0700 Subject: [PATCH 669/750] dev_printk(): constify the `dev' argument Add const markings to dev_name and dev_driver_string to make it clear that dev_printk doesn't modify dev. This is a prerequisite to adding more const markings to other functions make it clearer, which functions can modify dev and which can't. Signed-off-by: Jean Delvare Cc: Kay Sievers Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman --- drivers/base/core.c | 2 +- include/linux/device.h | 4 ++-- 2 files changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/base/core.c b/drivers/base/core.c index 068aa1c9538..44bad73d819 100644 --- a/drivers/base/core.c +++ b/drivers/base/core.c @@ -53,7 +53,7 @@ static inline int device_is_not_partition(struct device *dev) * it is attached to. If it is not attached to a bus either, an empty * string will be returned. */ -const char *dev_driver_string(struct device *dev) +const char *dev_driver_string(const struct device *dev) { return dev->driver ? dev->driver->name : (dev->bus ? dev->bus->name : diff --git a/include/linux/device.h b/include/linux/device.h index d24a47f80f9..a701c1b5184 100644 --- a/include/linux/device.h +++ b/include/linux/device.h @@ -406,7 +406,7 @@ struct device { /* Get the wakeup routines, which depend on struct device */ #include -static inline const char *dev_name(struct device *dev) +static inline const char *dev_name(const struct device *dev) { /* will be changed into kobject_name(&dev->kobj) in the near future */ return dev->bus_id; @@ -518,7 +518,7 @@ extern void device_shutdown(void); extern void sysdev_shutdown(void); /* debugging and troubleshooting/diagnostic helpers. */ -extern const char *dev_driver_string(struct device *dev); +extern const char *dev_driver_string(const struct device *dev); #define dev_printk(level, dev, format, arg...) \ printk(level "%s %s: " format , dev_driver_string(dev) , \ dev_name(dev) , ## arg) -- GitLab From 7c2250352e11bf956c4cfa20b01ae6ba72882788 Mon Sep 17 00:00:00 2001 From: David Brownell Date: Wed, 6 Aug 2008 18:52:44 -0700 Subject: [PATCH 670/750] driver model: anti-oopsing medicine Anti-oops medicine for the class iterators ... the oops was observed when a class was implicitly referenced before it was initialized. [Modified by Greg to spit a warning back so someone knows to fix their code] Signed-off-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/base/class.c | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/drivers/base/class.c b/drivers/base/class.c index 5667c2f02c5..cc5e28c8885 100644 --- a/drivers/base/class.c +++ b/drivers/base/class.c @@ -295,6 +295,12 @@ int class_for_each_device(struct class *class, struct device *start, if (!class) return -EINVAL; + if (!class->p) { + WARN(1, "%s called for class '%s' before it was initialized", + __func__, class->name); + return -EINVAL; + } + mutex_lock(&class->p->class_mutex); list_for_each_entry(dev, &class->p->class_devices, node) { if (start) { @@ -344,6 +350,11 @@ struct device *class_find_device(struct class *class, struct device *start, if (!class) return NULL; + if (!class->p) { + WARN(1, "%s called for class '%s' before it was initialized", + __func__, class->name); + return NULL; + } mutex_lock(&class->p->class_mutex); list_for_each_entry(dev, &class->p->class_devices, node) { -- GitLab From 3b98aeaf3a75f544dc945694f4fcf6e1c4bab89d Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Thu, 7 Aug 2008 13:06:12 -0400 Subject: [PATCH 671/750] PM: don't skip device PM init when CONFIG_PM_SLEEP isn't set and CONFIG_PM is set This patch (as1124) fixes a couple of bugs in the PM core. The new dev->power.status field should be initialized regardless of whether CONFIG_PM_SLEEP is enabled, and similarly dpm_sysfs_add() should be called whenever CONFIG_PM is enabled. The patch separates out the call to dpm_sysfs_add() from the call to device_pm_add(). As a result device_pm_add() can no longer return an error, so its return type is changed to void. Signed-off-by: Alan Stern Tested-by: Romit Dasgupta Acked-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman --- drivers/base/core.c | 9 ++++++--- drivers/base/power/main.c | 13 +++---------- drivers/base/power/power.h | 9 +++++++-- 3 files changed, 16 insertions(+), 15 deletions(-) diff --git a/drivers/base/core.c b/drivers/base/core.c index 44bad73d819..40041319657 100644 --- a/drivers/base/core.c +++ b/drivers/base/core.c @@ -541,6 +541,7 @@ void device_initialize(struct device *dev) spin_lock_init(&dev->devres_lock); INIT_LIST_HEAD(&dev->devres_head); device_init_wakeup(dev, 0); + device_pm_init(dev); set_dev_node(dev, -1); } @@ -897,9 +898,10 @@ int device_add(struct device *dev) error = bus_add_device(dev); if (error) goto BusError; - error = device_pm_add(dev); + error = dpm_sysfs_add(dev); if (error) - goto PMError; + goto DPMError; + device_pm_add(dev); kobject_uevent(&dev->kobj, KOBJ_ADD); bus_attach_device(dev); if (parent) @@ -920,7 +922,7 @@ int device_add(struct device *dev) Done: put_device(dev); return error; - PMError: + DPMError: bus_remove_device(dev); BusError: if (dev->bus) @@ -1007,6 +1009,7 @@ void device_del(struct device *dev) struct class_interface *class_intf; device_pm_remove(dev); + dpm_sysfs_remove(dev); if (parent) klist_del(&dev->knode_parent); if (MAJOR(dev->devt)) { diff --git a/drivers/base/power/main.c b/drivers/base/power/main.c index 3250c5257b7..284f564bb12 100644 --- a/drivers/base/power/main.c +++ b/drivers/base/power/main.c @@ -67,10 +67,8 @@ void device_pm_unlock(void) * device_pm_add - add a device to the list of active devices * @dev: Device to be added to the list */ -int device_pm_add(struct device *dev) +void device_pm_add(struct device *dev) { - int error; - pr_debug("PM: Adding info for %s:%s\n", dev->bus ? dev->bus->name : "No Bus", kobject_name(&dev->kobj)); @@ -89,13 +87,9 @@ int device_pm_add(struct device *dev) */ WARN_ON(true); } - error = dpm_sysfs_add(dev); - if (!error) { - dev->power.status = DPM_ON; - list_add_tail(&dev->power.entry, &dpm_list); - } + + list_add_tail(&dev->power.entry, &dpm_list); mutex_unlock(&dpm_list_mtx); - return error; } /** @@ -110,7 +104,6 @@ void device_pm_remove(struct device *dev) dev->bus ? dev->bus->name : "No Bus", kobject_name(&dev->kobj)); mutex_lock(&dpm_list_mtx); - dpm_sysfs_remove(dev); list_del_init(&dev->power.entry); mutex_unlock(&dpm_list_mtx); } diff --git a/drivers/base/power/power.h b/drivers/base/power/power.h index a3252c0e288..41f51fae042 100644 --- a/drivers/base/power/power.h +++ b/drivers/base/power/power.h @@ -1,3 +1,8 @@ +static inline void device_pm_init(struct device *dev) +{ + dev->power.status = DPM_ON; +} + #ifdef CONFIG_PM_SLEEP /* @@ -11,12 +16,12 @@ static inline struct device *to_device(struct list_head *entry) return container_of(entry, struct device, power.entry); } -extern int device_pm_add(struct device *); +extern void device_pm_add(struct device *); extern void device_pm_remove(struct device *); #else /* CONFIG_PM_SLEEP */ -static inline int device_pm_add(struct device *dev) { return 0; } +static inline void device_pm_add(struct device *dev) {} static inline void device_pm_remove(struct device *dev) {} #endif -- GitLab From c906a48adc74fc455378137ac5124b13e7030a15 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Fri, 30 May 2008 10:45:12 -0700 Subject: [PATCH 672/750] driver core: add init_name to struct device This gives us a way to handle both the bus_id and init_name values being used for a while during the transition period. Cc: Kay Sievers Signed-off-by: Greg Kroah-Hartman --- drivers/base/core.c | 20 +++++++++++++------- include/linux/device.h | 1 + 2 files changed, 14 insertions(+), 7 deletions(-) diff --git a/drivers/base/core.c b/drivers/base/core.c index 40041319657..d021c98605b 100644 --- a/drivers/base/core.c +++ b/drivers/base/core.c @@ -844,13 +844,19 @@ int device_add(struct device *dev) { struct device *parent = NULL; struct class_interface *class_intf; - int error; + int error = -EINVAL; dev = get_device(dev); - if (!dev || !strlen(dev->bus_id)) { - error = -EINVAL; - goto Done; - } + if (!dev) + goto done; + + /* Temporarily support init_name if it is set. + * It will override bus_id for now */ + if (dev->init_name) + dev_set_name(dev, "%s", dev->init_name); + + if (!strlen(dev->bus_id)) + goto done; pr_debug("device: '%s': %s\n", dev->bus_id, __func__); @@ -919,7 +925,7 @@ int device_add(struct device *dev) class_intf->add_dev(dev, class_intf); mutex_unlock(&dev->class->p->class_mutex); } - Done: +done: put_device(dev); return error; DPMError: @@ -946,7 +952,7 @@ int device_add(struct device *dev) cleanup_device_parent(dev); if (parent) put_device(parent); - goto Done; + goto done; } /** diff --git a/include/linux/device.h b/include/linux/device.h index a701c1b5184..4d8372d135d 100644 --- a/include/linux/device.h +++ b/include/linux/device.h @@ -358,6 +358,7 @@ struct device { struct kobject kobj; char bus_id[BUS_ID_SIZE]; /* position on parent bus */ + const char *init_name; /* initial name of the device */ struct device_type *type; unsigned uevent_suppress:1; -- GitLab From f5a6d958b5d0a10e7e7a9dee1862fb31d08c6d26 Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Sat, 9 Aug 2008 01:05:13 +0200 Subject: [PATCH 673/750] PM: Remove WARN_ON from device_pm_add PM: Remove WARN_ON from device_pm_add Fix message in device_pm_add() saying that the device will not be added to dpm_list, although in fact the device is going to be added to the list regardless of the ordering violation. Remove the WARN_ON(true) triggered in that situation, because it is hit by USB very often and spams the users' logs. This patch fixes bug #11263 Signed-off-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman --- drivers/base/power/main.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) diff --git a/drivers/base/power/main.c b/drivers/base/power/main.c index 284f564bb12..273a944d404 100644 --- a/drivers/base/power/main.c +++ b/drivers/base/power/main.c @@ -74,11 +74,9 @@ void device_pm_add(struct device *dev) kobject_name(&dev->kobj)); mutex_lock(&dpm_list_mtx); if (dev->parent) { - if (dev->parent->power.status >= DPM_SUSPENDING) { - dev_warn(dev, "parent %s is sleeping, will not add\n", + if (dev->parent->power.status >= DPM_SUSPENDING) + dev_warn(dev, "parent %s should not be sleeping\n", dev->parent->bus_id); - WARN_ON(true); - } } else if (transition_started) { /* * We refuse to register parentless devices while a PM -- GitLab From 068281d302def5efd96d84a163ba17e85f5ea564 Mon Sep 17 00:00:00 2001 From: Kay Sievers Date: Sat, 16 Aug 2008 14:30:30 +0200 Subject: [PATCH 674/750] block: fix partial read() of /proc/{partitions,diskstats} The proc files get truncated if they do not fit into the buffer with a single read(). We need to move the seq_file index from the callback of class_find_device() to the caller of class_find_device(), to keep its value across multiple invocations of the callback. Signed-off-by: Kay Sievers Signed-off-by: Greg Kroah-Hartman --- block/genhd.c | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-) diff --git a/block/genhd.c b/block/genhd.c index c13cc77291a..f34befc5484 100644 --- a/block/genhd.c +++ b/block/genhd.c @@ -293,25 +293,26 @@ void __init printk_all_partitions(void) /* iterator */ static int find_start(struct device *dev, void *data) { - loff_t k = *(loff_t *)data; + loff_t *k = data; if (dev->type != &disk_type) return 0; - if (!k--) + if (!*k) return 1; + (*k)--; return 0; } static void *part_start(struct seq_file *part, loff_t *pos) { struct device *dev; - loff_t n = *pos; + loff_t k = *pos; - if (!n) + if (!k) seq_puts(part, "major minor #blocks name\n\n"); mutex_lock(&block_class_lock); - dev = class_find_device(&block_class, NULL, (void *)pos, find_start); + dev = class_find_device(&block_class, NULL, &k, find_start); if (dev) return dev_to_disk(dev); return NULL; @@ -568,9 +569,10 @@ static struct device_type disk_type = { static void *diskstats_start(struct seq_file *part, loff_t *pos) { struct device *dev; + loff_t k = *pos; mutex_lock(&block_class_lock); - dev = class_find_device(&block_class, NULL, (void *)pos, find_start); + dev = class_find_device(&block_class, NULL, &k, find_start); if (dev) return dev_to_disk(dev); return NULL; -- GitLab From 5c0ef6d0214a08e5c846f4c45228adf135d8d0ef Mon Sep 17 00:00:00 2001 From: Kay Sievers Date: Sat, 16 Aug 2008 14:30:30 +0200 Subject: [PATCH 675/750] block: drop references taken by class_find_device() Otherwise we leak references, which is not a good thing to do. Signed-off-by: Kay Sievers Signed-off-by: Greg Kroah-Hartman --- block/genhd.c | 22 ++++++++++++++++------ 1 file changed, 16 insertions(+), 6 deletions(-) diff --git a/block/genhd.c b/block/genhd.c index f34befc5484..656c2c7abf9 100644 --- a/block/genhd.c +++ b/block/genhd.c @@ -313,8 +313,10 @@ static void *part_start(struct seq_file *part, loff_t *pos) mutex_lock(&block_class_lock); dev = class_find_device(&block_class, NULL, &k, find_start); - if (dev) + if (dev) { + put_device(dev); return dev_to_disk(dev); + } return NULL; } @@ -331,8 +333,10 @@ static void *part_next(struct seq_file *part, void *v, loff_t *pos) struct device *dev; ++*pos; dev = class_find_device(&block_class, &gp->dev, NULL, find_next); - if (dev) + if (dev) { + put_device(dev); return dev_to_disk(dev); + } return NULL; } @@ -573,8 +577,10 @@ static void *diskstats_start(struct seq_file *part, loff_t *pos) mutex_lock(&block_class_lock); dev = class_find_device(&block_class, NULL, &k, find_start); - if (dev) + if (dev) { + put_device(dev); return dev_to_disk(dev); + } return NULL; } @@ -585,8 +591,10 @@ static void *diskstats_next(struct seq_file *part, void *v, loff_t *pos) ++*pos; dev = class_find_device(&block_class, &gp->dev, NULL, find_next); - if (dev) + if (dev) { + put_device(dev); return dev_to_disk(dev); + } return NULL; } @@ -714,10 +722,12 @@ dev_t blk_lookup_devt(const char *name, int part) mutex_lock(&block_class_lock); find.name = name; find.part = part; - dev = class_find_device(&block_class, NULL, (void *)&find, match_id); - if (dev) + dev = class_find_device(&block_class, NULL, &find, match_id); + if (dev) { + put_device(dev); devt = MKDEV(MAJOR(dev->devt), MINOR(dev->devt) + part); + } mutex_unlock(&block_class_lock); return devt; -- GitLab From 331995e78385a0b9860f4c4c1766e842e61c450a Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= Date: Fri, 11 Jul 2008 11:10:36 +0200 Subject: [PATCH 676/750] UIO: uio_pdrv: fix memory leak MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Thanks to Magnus Damm for pointing that out. Signed-off-by: Uwe Kleine-König Cc: Magnus Damm Acked-by: Hans J. Koch Signed-off-by: Greg Kroah-Hartman --- drivers/uio/uio_pdrv.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/uio/uio_pdrv.c b/drivers/uio/uio_pdrv.c index 5d0d2e85d98..aa3bff8f93a 100644 --- a/drivers/uio/uio_pdrv.c +++ b/drivers/uio/uio_pdrv.c @@ -88,6 +88,8 @@ static int uio_pdrv_remove(struct platform_device *pdev) uio_unregister_device(pdata->uioinfo); + kfree(pdata); + return 0; } -- GitLab From 0f90927da11d596802d196cf299e91293abc90c5 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= Date: Fri, 11 Jul 2008 11:10:37 +0200 Subject: [PATCH 677/750] UIO: uio_pdrv: fix license specification MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Thanks to Magnus Damm for pointing that out. Signed-off-by: Uwe Kleine-König Cc: Magnus Damm Acked-by: Hans J. Koch Signed-off-by: Greg Kroah-Hartman --- drivers/uio/uio_pdrv.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/uio/uio_pdrv.c b/drivers/uio/uio_pdrv.c index aa3bff8f93a..0b4ef39cd85 100644 --- a/drivers/uio/uio_pdrv.c +++ b/drivers/uio/uio_pdrv.c @@ -116,5 +116,5 @@ module_exit(uio_pdrv_exit); MODULE_AUTHOR("Uwe Kleine-Koenig"); MODULE_DESCRIPTION("Userspace I/O platform driver"); -MODULE_LICENSE("GPL"); +MODULE_LICENSE("GPL v2"); MODULE_ALIAS("platform:" DRIVER_NAME); -- GitLab From c767db0ab4bc85f06119f2b42369e31b29991f16 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Fri, 11 Jul 2008 18:55:27 +0900 Subject: [PATCH 678/750] UIO: generic irq handling for some uio platform devices This is V3 of uio_pdrv_genirq.c, a platform driver for UIO with generic IRQ handling code. This driver is very similar to the regular UIO platform driver, but is only suitable for devices that are connected to the interrupt controller using unique interrupt lines. The uio_pdrv_genirq driver includes generic interrupt handling code which disables the serviced interrupt in the interrupt controller and makes the user space driver responsible for acknowledging the interrupt in the device and reenabling the interrupt in the interrupt controller. Shared interrupts are not supported since the in-kernel interrupt handler will disable the interrupt line in the interrupt controller, and in a shared interrupt configuration this will stop other devices from delivering interrupts. Signed-off-by: Magnus Damm Signed-off-by: Hans J. Koch Signed-off-by: Greg Kroah-Hartman --- drivers/uio/Kconfig | 13 +++ drivers/uio/Makefile | 1 + drivers/uio/uio_pdrv_genirq.c | 188 ++++++++++++++++++++++++++++++++++ 3 files changed, 202 insertions(+) create mode 100644 drivers/uio/uio_pdrv_genirq.c diff --git a/drivers/uio/Kconfig b/drivers/uio/Kconfig index 2e9079df26b..4190be64917 100644 --- a/drivers/uio/Kconfig +++ b/drivers/uio/Kconfig @@ -33,6 +33,19 @@ config UIO_PDRV If you don't know what to do here, say N. +config UIO_PDRV_GENIRQ + tristate "Userspace I/O platform driver with generic IRQ handling" + help + Platform driver for Userspace I/O devices, including generic + interrupt handling code. Shared interrupts are not supported. + + This kernel driver requires that the matching userspace driver + handles interrupts in a special way. Userspace is responsible + for acknowledging the hardware device if needed, and re-enabling + interrupts in the interrupt controller using the write() syscall. + + If you don't know what to do here, say N. + config UIO_SMX tristate "SMX cryptengine UIO interface" default n diff --git a/drivers/uio/Makefile b/drivers/uio/Makefile index e00ce0def1a..8667bbdef90 100644 --- a/drivers/uio/Makefile +++ b/drivers/uio/Makefile @@ -1,4 +1,5 @@ obj-$(CONFIG_UIO) += uio.o obj-$(CONFIG_UIO_CIF) += uio_cif.o obj-$(CONFIG_UIO_PDRV) += uio_pdrv.o +obj-$(CONFIG_UIO_PDRV_GENIRQ) += uio_pdrv_genirq.o obj-$(CONFIG_UIO_SMX) += uio_smx.o diff --git a/drivers/uio/uio_pdrv_genirq.c b/drivers/uio/uio_pdrv_genirq.c new file mode 100644 index 00000000000..1f82c83a92a --- /dev/null +++ b/drivers/uio/uio_pdrv_genirq.c @@ -0,0 +1,188 @@ +/* + * drivers/uio/uio_pdrv_genirq.c + * + * Userspace I/O platform driver with generic IRQ handling code. + * + * Copyright (C) 2008 Magnus Damm + * + * Based on uio_pdrv.c by Uwe Kleine-Koenig, + * Copyright (C) 2008 by Digi International Inc. + * All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include + +#define DRIVER_NAME "uio_pdrv_genirq" + +struct uio_pdrv_genirq_platdata { + struct uio_info *uioinfo; + spinlock_t lock; + unsigned long flags; +}; + +static irqreturn_t uio_pdrv_genirq_handler(int irq, struct uio_info *dev_info) +{ + struct uio_pdrv_genirq_platdata *priv = dev_info->priv; + + /* Just disable the interrupt in the interrupt controller, and + * remember the state so we can allow user space to enable it later. + */ + + if (!test_and_set_bit(0, &priv->flags)) + disable_irq_nosync(irq); + + return IRQ_HANDLED; +} + +static int uio_pdrv_genirq_irqcontrol(struct uio_info *dev_info, s32 irq_on) +{ + struct uio_pdrv_genirq_platdata *priv = dev_info->priv; + unsigned long flags; + + /* Allow user space to enable and disable the interrupt + * in the interrupt controller, but keep track of the + * state to prevent per-irq depth damage. + * + * Serialize this operation to support multiple tasks. + */ + + spin_lock_irqsave(&priv->lock, flags); + if (irq_on) { + if (test_and_clear_bit(0, &priv->flags)) + enable_irq(dev_info->irq); + } else { + if (!test_and_set_bit(0, &priv->flags)) + disable_irq(dev_info->irq); + } + spin_unlock_irqrestore(&priv->lock, flags); + + return 0; +} + +static int uio_pdrv_genirq_probe(struct platform_device *pdev) +{ + struct uio_info *uioinfo = pdev->dev.platform_data; + struct uio_pdrv_genirq_platdata *priv; + struct uio_mem *uiomem; + int ret = -EINVAL; + int i; + + if (!uioinfo || !uioinfo->name || !uioinfo->version) { + dev_err(&pdev->dev, "missing platform_data\n"); + goto bad0; + } + + if (uioinfo->handler || uioinfo->irqcontrol || uioinfo->irq_flags) { + dev_err(&pdev->dev, "interrupt configuration error\n"); + goto bad0; + } + + priv = kzalloc(sizeof(*priv), GFP_KERNEL); + if (!priv) { + ret = -ENOMEM; + dev_err(&pdev->dev, "unable to kmalloc\n"); + goto bad0; + } + + priv->uioinfo = uioinfo; + spin_lock_init(&priv->lock); + priv->flags = 0; /* interrupt is enabled to begin with */ + + uiomem = &uioinfo->mem[0]; + + for (i = 0; i < pdev->num_resources; ++i) { + struct resource *r = &pdev->resource[i]; + + if (r->flags != IORESOURCE_MEM) + continue; + + if (uiomem >= &uioinfo->mem[MAX_UIO_MAPS]) { + dev_warn(&pdev->dev, "device has more than " + __stringify(MAX_UIO_MAPS) + " I/O memory resources.\n"); + break; + } + + uiomem->memtype = UIO_MEM_PHYS; + uiomem->addr = r->start; + uiomem->size = r->end - r->start + 1; + ++uiomem; + } + + while (uiomem < &uioinfo->mem[MAX_UIO_MAPS]) { + uiomem->size = 0; + ++uiomem; + } + + /* This driver requires no hardware specific kernel code to handle + * interrupts. Instead, the interrupt handler simply disables the + * interrupt in the interrupt controller. User space is responsible + * for performing hardware specific acknowledge and re-enabling of + * the interrupt in the interrupt controller. + * + * Interrupt sharing is not supported. + */ + + uioinfo->irq_flags = IRQF_DISABLED; + uioinfo->handler = uio_pdrv_genirq_handler; + uioinfo->irqcontrol = uio_pdrv_genirq_irqcontrol; + uioinfo->priv = priv; + + ret = uio_register_device(&pdev->dev, priv->uioinfo); + if (ret) { + dev_err(&pdev->dev, "unable to register uio device\n"); + goto bad1; + } + + platform_set_drvdata(pdev, priv); + return 0; + bad1: + kfree(priv); + bad0: + return ret; +} + +static int uio_pdrv_genirq_remove(struct platform_device *pdev) +{ + struct uio_pdrv_genirq_platdata *priv = platform_get_drvdata(pdev); + + uio_unregister_device(priv->uioinfo); + kfree(priv); + return 0; +} + +static struct platform_driver uio_pdrv_genirq = { + .probe = uio_pdrv_genirq_probe, + .remove = uio_pdrv_genirq_remove, + .driver = { + .name = DRIVER_NAME, + .owner = THIS_MODULE, + }, +}; + +static int __init uio_pdrv_genirq_init(void) +{ + return platform_driver_register(&uio_pdrv_genirq); +} + +static void __exit uio_pdrv_genirq_exit(void) +{ + platform_driver_unregister(&uio_pdrv_genirq); +} + +module_init(uio_pdrv_genirq_init); +module_exit(uio_pdrv_genirq_exit); + +MODULE_AUTHOR("Magnus Damm"); +MODULE_DESCRIPTION("Userspace I/O platform driver with generic IRQ handling"); +MODULE_LICENSE("GPL v2"); +MODULE_ALIAS("platform:" DRIVER_NAME); -- GitLab From 5e4c6564c95ce127beeefe75e15cd11c93487436 Mon Sep 17 00:00:00 2001 From: Kay Sievers Date: Thu, 21 Aug 2008 15:28:56 +0200 Subject: [PATCH 679/750] pnp: fix "add acpi:* modalias entries" With 22454cb99fc39f2629ad06a7eccb3df312f8830e we added only the first entry of the device table. We need to loop over the whole device list. Signed-off-by: Kay Sievers Signed-off-by: Greg Kroah-Hartman --- scripts/mod/file2alias.c | 16 +++++++++++----- 1 file changed, 11 insertions(+), 5 deletions(-) diff --git a/scripts/mod/file2alias.c b/scripts/mod/file2alias.c index 4fa1f3ad251..4c9890ec252 100644 --- a/scripts/mod/file2alias.c +++ b/scripts/mod/file2alias.c @@ -344,14 +344,20 @@ static void do_pnp_device_entry(void *symval, unsigned long size, struct module *mod) { const unsigned long id_size = sizeof(struct pnp_device_id); - const struct pnp_device_id *id = symval; + const unsigned int count = (size / id_size)-1; + const struct pnp_device_id *devs = symval; + unsigned int i; device_id_check(mod->name, "pnp", size, id_size, symval); - buf_printf(&mod->dev_table_buf, - "MODULE_ALIAS(\"pnp:d%s*\");\n", id->id); - buf_printf(&mod->dev_table_buf, - "MODULE_ALIAS(\"acpi*:%s:*\");\n", id->id); + for (i = 0; i < count; i++) { + const char *id = (char *)devs[i].id; + + buf_printf(&mod->dev_table_buf, + "MODULE_ALIAS(\"pnp:d%s*\");\n", id); + buf_printf(&mod->dev_table_buf, + "MODULE_ALIAS(\"acpi*:%s:*\");\n", id); + } } /* looks like: "pnp:dD" for every device of the card */ -- GitLab From 380ec6780a0461bb4a4592484d6fe75aa096edeb Mon Sep 17 00:00:00 2001 From: Enrico Scholz Date: Wed, 20 Aug 2008 00:06:22 +0200 Subject: [PATCH 680/750] USB: ISP1760: fixed trivial math in comment Signed-off-by: Enrico Scholz Acked-by: Sebastian Siewior Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/isp1760-hcd.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/host/isp1760-hcd.c b/drivers/usb/host/isp1760-hcd.c index d22a84f86a3..8017f1cf78e 100644 --- a/drivers/usb/host/isp1760-hcd.c +++ b/drivers/usb/host/isp1760-hcd.c @@ -988,7 +988,7 @@ static void do_atl_int(struct usb_hcd *usb_hcd) /* * write bank1 address twice to ensure the 90ns delay (time * between BANK0 write and the priv_read_copy() call is at - * least 3*t_WHWL + 2*t_w11 = 3*25ns + 2*17ns = 92ns) + * least 3*t_WHWL + 2*t_w11 = 3*25ns + 2*17ns = 109ns) */ isp1760_writel(payload + ISP_BANK(1), usb_hcd->regs + HC_MEMORY_REG); -- GitLab From f8033827d8e92db6159d34ed45c608522674ecd8 Mon Sep 17 00:00:00 2001 From: Hiroshi Miura Date: Tue, 19 Aug 2008 10:58:25 +0200 Subject: [PATCH 681/750] usb-serial: option support HSDPA modem A2502 This patch support NTT DoCoMo A2502 3G/HSDPA modem on option driver. It is produced by AnyDATA Corp. and also sold as KT Freetelecom (Korea) ADU 620UW. It support 3.6Mbps/7.2Mbps hight speed communication. I have tested A2502 with NTT DoCoMo MoperaU ISP service. Signed-off-by: Hiroshi Miura Signed-off-by: Matthias Urlichs Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index e143198aeb0..9f9cd36455f 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -173,6 +173,7 @@ static int option_send_setup(struct tty_struct *tty, struct usb_serial_port *po #define KYOCERA_PRODUCT_KPC680 0x180a #define ANYDATA_VENDOR_ID 0x16d5 +#define ANYDATA_PRODUCT_ADU_620UW 0x6202 #define ANYDATA_PRODUCT_ADU_E100A 0x6501 #define ANYDATA_PRODUCT_ADU_500A 0x6502 @@ -318,6 +319,7 @@ static struct usb_device_id option_ids[] = { { USB_DEVICE(DELL_VENDOR_ID, 0x8138) }, /* Dell Wireless 5520 Voda I Mobile Broadband (3G HSDPA) Minicard */ { USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_E100A) }, { USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_500A) }, + { USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_620UW) }, { USB_DEVICE(AXESSTEL_VENDOR_ID, AXESSTEL_PRODUCT_MV110H) }, { USB_DEVICE(ONDA_VENDOR_ID, ONDA_PRODUCT_MSA501HS) }, { USB_DEVICE(ONDA_VENDOR_ID, ONDA_PRODUCT_ET502HS) }, -- GitLab From 77571f05a483c0259e42ba2f482c82debc9a63af Mon Sep 17 00:00:00 2001 From: Oliver Neukum Date: Mon, 18 Aug 2008 16:36:52 +0200 Subject: [PATCH 682/750] USB: fix bug in usb_unlink_anchored_urbs() Irqs must not accidentally be reenabled. Signed-off-by: Oliver Neukum Acked-by: Marcel Holtmann Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/urb.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) diff --git a/drivers/usb/core/urb.c b/drivers/usb/core/urb.c index c0b1ae25ae2..47111e88f79 100644 --- a/drivers/usb/core/urb.c +++ b/drivers/usb/core/urb.c @@ -601,15 +601,20 @@ EXPORT_SYMBOL_GPL(usb_kill_anchored_urbs); void usb_unlink_anchored_urbs(struct usb_anchor *anchor) { struct urb *victim; + unsigned long flags; - spin_lock_irq(&anchor->lock); + spin_lock_irqsave(&anchor->lock, flags); while (!list_empty(&anchor->urb_list)) { victim = list_entry(anchor->urb_list.prev, struct urb, anchor_list); + usb_get_urb(victim); + spin_unlock_irqrestore(&anchor->lock, flags); /* this will unanchor the URB */ usb_unlink_urb(victim); + usb_put_urb(victim); + spin_lock_irqsave(&anchor->lock, flags); } - spin_unlock_irq(&anchor->lock); + spin_unlock_irqrestore(&anchor->lock, flags); } EXPORT_SYMBOL_GPL(usb_unlink_anchored_urbs); -- GitLab From c8fd2c37b99c55c8d24888e0ed9d5f4f73458c9c Mon Sep 17 00:00:00 2001 From: Eric Sandeen Date: Thu, 14 Aug 2008 08:25:40 -0500 Subject: [PATCH 683/750] USB: cdc-acm: quirk for Conexant CX93010 USB modem This patch gets my Rosewill RNX-56USB USB modem (with Conexant CX93010 chipset) up and running to the point where I can send AT commands and retrieve caller ID data, which is all I want to do with it. Signed-off-by: Eric Sandeen Acked-by: Oliver Neukum Signed-off-by: Greg Kroah-Hartman --- drivers/usb/class/cdc-acm.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index efc4373eded..382522eb1f7 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -1362,6 +1362,9 @@ static struct usb_device_id acm_ids[] = { { USB_DEVICE(0x0803, 0x3095), /* Zoom Telephonics Model 3095F USB MODEM */ .driver_info = NO_UNION_NORMAL, /* has no union descriptor */ }, + { USB_DEVICE(0x0572, 0x1321), /* Conexant USB MODEM CX93010 */ + .driver_info = NO_UNION_NORMAL, /* has no union descriptor */ + }, /* control interfaces with various AT-command sets */ { USB_INTERFACE_INFO(USB_CLASS_COMM, USB_CDC_SUBCLASS_ACM, -- GitLab From bf31338bfd5d04434adf2294255847bb7dad687a Mon Sep 17 00:00:00 2001 From: Robert Jarzmik Date: Mon, 11 Aug 2008 18:28:13 +0200 Subject: [PATCH 684/750] USB: Fix pxa27x_udc usb speed handling. The new composite framework revealed a weakness in the pxa27x_udc driver gadget register function. Instead of checking if speed asked for was USB_LOW_SPEED upon usb_gadget_register() to deny service, it checked only for USB_FULL_SPEED, thus denying service to usb high speed capable gadgets (like g_ether). Signed-off-by: Robert Jarzmik Cc: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/pxa27x_udc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/gadget/pxa27x_udc.c b/drivers/usb/gadget/pxa27x_udc.c index a28513ecbe5..7cbc78a6853 100644 --- a/drivers/usb/gadget/pxa27x_udc.c +++ b/drivers/usb/gadget/pxa27x_udc.c @@ -1622,7 +1622,7 @@ int usb_gadget_register_driver(struct usb_gadget_driver *driver) struct pxa_udc *udc = the_controller; int retval; - if (!driver || driver->speed != USB_SPEED_FULL || !driver->bind + if (!driver || driver->speed < USB_SPEED_FULL || !driver->bind || !driver->disconnect || !driver->setup) return -EINVAL; if (!udc) -- GitLab From 746cdd0b2d1254b11382789b6630c4d379bdcf13 Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Sun, 10 Aug 2008 21:22:34 +0300 Subject: [PATCH 685/750] usb: musb: get rid of procfs entry Drivers should not add procfs. The functionality in the old procfs file will be moved to debugfs. Cc: Anand Gadiyar Cc: Bryan Wu Cc: David Brownell Signed-off-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman --- drivers/usb/musb/Makefile | 5 - drivers/usb/musb/musb_core.c | 21 +- drivers/usb/musb/musb_core.h | 19 - drivers/usb/musb/musb_procfs.c | 830 --------------------------------- 4 files changed, 11 insertions(+), 864 deletions(-) delete mode 100644 drivers/usb/musb/musb_procfs.c diff --git a/drivers/usb/musb/Makefile b/drivers/usb/musb/Makefile index 88eb67de08a..860369c7cbe 100644 --- a/drivers/usb/musb/Makefile +++ b/drivers/usb/musb/Makefile @@ -76,11 +76,6 @@ endif ifneq ($(MUSB_DEBUG),0) EXTRA_CFLAGS += -DDEBUG - - ifeq ($(CONFIG_PROC_FS),y) - musb_hdrc-objs += musb_procfs.o - endif - endif EXTRA_CFLAGS += -DMUSB_DEBUG=$(MUSB_DEBUG) diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c index d68ec6daf33..99690ba436d 100644 --- a/drivers/usb/musb/musb_core.c +++ b/drivers/usb/musb/musb_core.c @@ -2037,6 +2037,8 @@ bad_config: musb->xceiv.state = OTG_STATE_A_IDLE; status = usb_add_hcd(musb_to_hcd(musb), -1, 0); + if (status) + goto fail; DBG(1, "%s mode, status %d, devctl %02x %c\n", "HOST", status, @@ -2051,6 +2053,8 @@ bad_config: musb->xceiv.state = OTG_STATE_B_IDLE; status = musb_gadget_setup(musb); + if (status) + goto fail; DBG(1, "%s mode, status %d, dev%02x\n", is_otg_enabled(musb) ? "OTG" : "PERIPHERAL", @@ -2059,16 +2063,14 @@ bad_config: } - if (status == 0) - musb_debug_create("driver/musb_hdrc", musb); - else { + return 0; + fail: - if (musb->clock) - clk_put(musb->clock); - device_init_wakeup(dev, 0); - musb_free(musb); - return status; - } + if (musb->clock) + clk_put(musb->clock); + device_init_wakeup(dev, 0); + musb_free(musb); + return status; #ifdef CONFIG_SYSFS status = device_create_file(dev, &dev_attr_mode); @@ -2131,7 +2133,6 @@ static int __devexit musb_remove(struct platform_device *pdev) * - OTG mode: both roles are deactivated (or never-activated) */ musb_shutdown(pdev); - musb_debug_delete("driver/musb_hdrc", musb); #ifdef CONFIG_USB_MUSB_HDRC_HCD if (musb->board_mode == MUSB_HOST) usb_remove_hcd(musb_to_hcd(musb)); diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h index eade46d8170..82227251931 100644 --- a/drivers/usb/musb/musb_core.h +++ b/drivers/usb/musb/musb_core.h @@ -485,23 +485,4 @@ extern int musb_platform_get_vbus_status(struct musb *musb); extern int __init musb_platform_init(struct musb *musb); extern int musb_platform_exit(struct musb *musb); -/*-------------------------- ProcFS definitions ---------------------*/ - -struct proc_dir_entry; - -#if (MUSB_DEBUG > 0) && defined(MUSB_CONFIG_PROC_FS) -extern struct proc_dir_entry *musb_debug_create(char *name, struct musb *data); -extern void musb_debug_delete(char *name, struct musb *data); - -#else -static inline struct proc_dir_entry * -musb_debug_create(char *name, struct musb *data) -{ - return NULL; -} -static inline void musb_debug_delete(char *name, struct musb *data) -{ -} -#endif - #endif /* __MUSB_CORE_H__ */ diff --git a/drivers/usb/musb/musb_procfs.c b/drivers/usb/musb/musb_procfs.c deleted file mode 100644 index 55e6b78bdcc..00000000000 --- a/drivers/usb/musb/musb_procfs.c +++ /dev/null @@ -1,830 +0,0 @@ -/* - * MUSB OTG driver debug support - * - * Copyright 2005 Mentor Graphics Corporation - * Copyright (C) 2005-2006 by Texas Instruments - * Copyright (C) 2006-2007 Nokia Corporation - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * version 2 as published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, but - * WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU - * General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA - * 02110-1301 USA - * - * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN - * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT - * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF - * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON - * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF - * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - */ - -#include -#include -#include -#include /* FIXME remove procfs writes */ -#include - -#include "musb_core.h" - -#include "davinci.h" - -#ifdef CONFIG_USB_MUSB_HDRC_HCD - -static int dump_qh(struct musb_qh *qh, char *buf, unsigned max) -{ - int count; - int tmp; - struct usb_host_endpoint *hep = qh->hep; - struct urb *urb; - - count = snprintf(buf, max, " qh %p dev%d ep%d%s max%d\n", - qh, qh->dev->devnum, qh->epnum, - ({ char *s; switch (qh->type) { - case USB_ENDPOINT_XFER_BULK: - s = "-bulk"; break; - case USB_ENDPOINT_XFER_INT: - s = "-int"; break; - case USB_ENDPOINT_XFER_CONTROL: - s = ""; break; - default: - s = "iso"; break; - }; s; }), - qh->maxpacket); - if (count <= 0) - return 0; - buf += count; - max -= count; - - list_for_each_entry(urb, &hep->urb_list, urb_list) { - tmp = snprintf(buf, max, "\t%s urb %p %d/%d\n", - usb_pipein(urb->pipe) ? "in" : "out", - urb, urb->actual_length, - urb->transfer_buffer_length); - if (tmp <= 0) - break; - tmp = min(tmp, (int)max); - count += tmp; - buf += tmp; - max -= tmp; - } - return count; -} - -static int -dump_queue(struct list_head *q, char *buf, unsigned max) -{ - int count = 0; - struct musb_qh *qh; - - list_for_each_entry(qh, q, ring) { - int tmp; - - tmp = dump_qh(qh, buf, max); - if (tmp <= 0) - break; - tmp = min(tmp, (int)max); - count += tmp; - buf += tmp; - max -= tmp; - } - return count; -} - -#endif /* HCD */ - -#ifdef CONFIG_USB_GADGET_MUSB_HDRC -static int dump_ep(struct musb_ep *ep, char *buffer, unsigned max) -{ - char *buf = buffer; - int code = 0; - void __iomem *regs = ep->hw_ep->regs; - char *mode = "1buf"; - - if (ep->is_in) { - if (ep->hw_ep->tx_double_buffered) - mode = "2buf"; - } else { - if (ep->hw_ep->rx_double_buffered) - mode = "2buf"; - } - - do { - struct usb_request *req; - - code = snprintf(buf, max, - "\n%s (hw%d): %s%s, csr %04x maxp %04x\n", - ep->name, ep->current_epnum, - mode, ep->dma ? " dma" : "", - musb_readw(regs, - (ep->is_in || !ep->current_epnum) - ? MUSB_TXCSR - : MUSB_RXCSR), - musb_readw(regs, ep->is_in - ? MUSB_TXMAXP - : MUSB_RXMAXP) - ); - if (code <= 0) - break; - code = min(code, (int) max); - buf += code; - max -= code; - - if (is_cppi_enabled() && ep->current_epnum) { - unsigned cppi = ep->current_epnum - 1; - void __iomem *base = ep->musb->ctrl_base; - unsigned off1 = cppi << 2; - void __iomem *ram = base; - char tmp[16]; - - if (ep->is_in) { - ram += DAVINCI_TXCPPI_STATERAM_OFFSET(cppi); - tmp[0] = 0; - } else { - ram += DAVINCI_RXCPPI_STATERAM_OFFSET(cppi); - snprintf(tmp, sizeof tmp, "%d left, ", - musb_readl(base, - DAVINCI_RXCPPI_BUFCNT0_REG + off1)); - } - - code = snprintf(buf, max, "%cX DMA%d: %s" - "%08x %08x, %08x %08x; " - "%08x %08x %08x .. %08x\n", - ep->is_in ? 'T' : 'R', - ep->current_epnum - 1, tmp, - musb_readl(ram, 0 * 4), - musb_readl(ram, 1 * 4), - musb_readl(ram, 2 * 4), - musb_readl(ram, 3 * 4), - musb_readl(ram, 4 * 4), - musb_readl(ram, 5 * 4), - musb_readl(ram, 6 * 4), - musb_readl(ram, 7 * 4)); - if (code <= 0) - break; - code = min(code, (int) max); - buf += code; - max -= code; - } - - if (list_empty(&ep->req_list)) { - code = snprintf(buf, max, "\t(queue empty)\n"); - if (code <= 0) - break; - code = min(code, (int) max); - buf += code; - max -= code; - break; - } - list_for_each_entry(req, &ep->req_list, list) { - code = snprintf(buf, max, "\treq %p, %s%s%d/%d\n", - req, - req->zero ? "zero, " : "", - req->short_not_ok ? "!short, " : "", - req->actual, req->length); - if (code <= 0) - break; - code = min(code, (int) max); - buf += code; - max -= code; - } - } while (0); - return buf - buffer; -} -#endif - -static int -dump_end_info(struct musb *musb, u8 epnum, char *aBuffer, unsigned max) -{ - int code = 0; - char *buf = aBuffer; - struct musb_hw_ep *hw_ep = &musb->endpoints[epnum]; - - do { - musb_ep_select(musb->mregs, epnum); -#ifdef CONFIG_USB_MUSB_HDRC_HCD - if (is_host_active(musb)) { - int dump_rx, dump_tx; - void __iomem *regs = hw_ep->regs; - - /* TEMPORARY (!) until we have a real periodic - * schedule tree ... - */ - if (!epnum) { - /* control is shared, uses RX queue - * but (mostly) shadowed tx registers - */ - dump_tx = !list_empty(&musb->control); - dump_rx = 0; - } else if (hw_ep == musb->bulk_ep) { - dump_tx = !list_empty(&musb->out_bulk); - dump_rx = !list_empty(&musb->in_bulk); - } else if (musb->periodic[epnum]) { - struct usb_host_endpoint *hep; - - hep = musb->periodic[epnum]->hep; - dump_rx = hep->desc.bEndpointAddress - & USB_ENDPOINT_DIR_MASK; - dump_tx = !dump_rx; - } else - break; - /* END TEMPORARY */ - - - if (dump_rx) { - code = snprintf(buf, max, - "\nRX%d: %s rxcsr %04x interval %02x " - "max %04x type %02x; " - "dev %d hub %d port %d" - "\n", - epnum, - hw_ep->rx_double_buffered - ? "2buf" : "1buf", - musb_readw(regs, MUSB_RXCSR), - musb_readb(regs, MUSB_RXINTERVAL), - musb_readw(regs, MUSB_RXMAXP), - musb_readb(regs, MUSB_RXTYPE), - /* FIXME: assumes multipoint */ - musb_readb(musb->mregs, - MUSB_BUSCTL_OFFSET(epnum, - MUSB_RXFUNCADDR)), - musb_readb(musb->mregs, - MUSB_BUSCTL_OFFSET(epnum, - MUSB_RXHUBADDR)), - musb_readb(musb->mregs, - MUSB_BUSCTL_OFFSET(epnum, - MUSB_RXHUBPORT)) - ); - if (code <= 0) - break; - code = min(code, (int) max); - buf += code; - max -= code; - - if (is_cppi_enabled() - && epnum - && hw_ep->rx_channel) { - unsigned cppi = epnum - 1; - unsigned off1 = cppi << 2; - void __iomem *base; - void __iomem *ram; - char tmp[16]; - - base = musb->ctrl_base; - ram = DAVINCI_RXCPPI_STATERAM_OFFSET( - cppi) + base; - snprintf(tmp, sizeof tmp, "%d left, ", - musb_readl(base, - DAVINCI_RXCPPI_BUFCNT0_REG - + off1)); - - code = snprintf(buf, max, - " rx dma%d: %s" - "%08x %08x, %08x %08x; " - "%08x %08x %08x .. %08x\n", - cppi, tmp, - musb_readl(ram, 0 * 4), - musb_readl(ram, 1 * 4), - musb_readl(ram, 2 * 4), - musb_readl(ram, 3 * 4), - musb_readl(ram, 4 * 4), - musb_readl(ram, 5 * 4), - musb_readl(ram, 6 * 4), - musb_readl(ram, 7 * 4)); - if (code <= 0) - break; - code = min(code, (int) max); - buf += code; - max -= code; - } - - if (hw_ep == musb->bulk_ep - && !list_empty( - &musb->in_bulk)) { - code = dump_queue(&musb->in_bulk, - buf, max); - if (code <= 0) - break; - code = min(code, (int) max); - buf += code; - max -= code; - } else if (musb->periodic[epnum]) { - code = dump_qh(musb->periodic[epnum], - buf, max); - if (code <= 0) - break; - code = min(code, (int) max); - buf += code; - max -= code; - } - } - - if (dump_tx) { - code = snprintf(buf, max, - "\nTX%d: %s txcsr %04x interval %02x " - "max %04x type %02x; " - "dev %d hub %d port %d" - "\n", - epnum, - hw_ep->tx_double_buffered - ? "2buf" : "1buf", - musb_readw(regs, MUSB_TXCSR), - musb_readb(regs, MUSB_TXINTERVAL), - musb_readw(regs, MUSB_TXMAXP), - musb_readb(regs, MUSB_TXTYPE), - /* FIXME: assumes multipoint */ - musb_readb(musb->mregs, - MUSB_BUSCTL_OFFSET(epnum, - MUSB_TXFUNCADDR)), - musb_readb(musb->mregs, - MUSB_BUSCTL_OFFSET(epnum, - MUSB_TXHUBADDR)), - musb_readb(musb->mregs, - MUSB_BUSCTL_OFFSET(epnum, - MUSB_TXHUBPORT)) - ); - if (code <= 0) - break; - code = min(code, (int) max); - buf += code; - max -= code; - - if (is_cppi_enabled() - && epnum - && hw_ep->tx_channel) { - unsigned cppi = epnum - 1; - void __iomem *base; - void __iomem *ram; - - base = musb->ctrl_base; - ram = DAVINCI_RXCPPI_STATERAM_OFFSET( - cppi) + base; - code = snprintf(buf, max, - " tx dma%d: " - "%08x %08x, %08x %08x; " - "%08x %08x %08x .. %08x\n", - cppi, - musb_readl(ram, 0 * 4), - musb_readl(ram, 1 * 4), - musb_readl(ram, 2 * 4), - musb_readl(ram, 3 * 4), - musb_readl(ram, 4 * 4), - musb_readl(ram, 5 * 4), - musb_readl(ram, 6 * 4), - musb_readl(ram, 7 * 4)); - if (code <= 0) - break; - code = min(code, (int) max); - buf += code; - max -= code; - } - - if (hw_ep == musb->control_ep - && !list_empty( - &musb->control)) { - code = dump_queue(&musb->control, - buf, max); - if (code <= 0) - break; - code = min(code, (int) max); - buf += code; - max -= code; - } else if (hw_ep == musb->bulk_ep - && !list_empty( - &musb->out_bulk)) { - code = dump_queue(&musb->out_bulk, - buf, max); - if (code <= 0) - break; - code = min(code, (int) max); - buf += code; - max -= code; - } else if (musb->periodic[epnum]) { - code = dump_qh(musb->periodic[epnum], - buf, max); - if (code <= 0) - break; - code = min(code, (int) max); - buf += code; - max -= code; - } - } - } -#endif -#ifdef CONFIG_USB_GADGET_MUSB_HDRC - if (is_peripheral_active(musb)) { - code = 0; - - if (hw_ep->ep_in.desc || !epnum) { - code = dump_ep(&hw_ep->ep_in, buf, max); - if (code <= 0) - break; - code = min(code, (int) max); - buf += code; - max -= code; - } - if (hw_ep->ep_out.desc) { - code = dump_ep(&hw_ep->ep_out, buf, max); - if (code <= 0) - break; - code = min(code, (int) max); - buf += code; - max -= code; - } - } -#endif - } while (0); - - return buf - aBuffer; -} - -/* Dump the current status and compile options. - * @param musb the device driver instance - * @param buffer where to dump the status; it must be big enough to hold the - * result otherwise "BAD THINGS HAPPENS(TM)". - */ -static int dump_header_stats(struct musb *musb, char *buffer) -{ - int code, count = 0; - const void __iomem *mbase = musb->mregs; - - *buffer = 0; - count = sprintf(buffer, "Status: %sHDRC, Mode=%s " - "(Power=%02x, DevCtl=%02x)\n", - (musb->is_multipoint ? "M" : ""), MUSB_MODE(musb), - musb_readb(mbase, MUSB_POWER), - musb_readb(mbase, MUSB_DEVCTL)); - if (count <= 0) - return 0; - buffer += count; - - code = sprintf(buffer, "OTG state: %s; %sactive\n", - otg_state_string(musb), - musb->is_active ? "" : "in"); - if (code <= 0) - goto done; - buffer += code; - count += code; - - code = sprintf(buffer, - "Options: " -#ifdef CONFIG_MUSB_PIO_ONLY - "pio" -#elif defined(CONFIG_USB_TI_CPPI_DMA) - "cppi-dma" -#elif defined(CONFIG_USB_INVENTRA_DMA) - "musb-dma" -#elif defined(CONFIG_USB_TUSB_OMAP_DMA) - "tusb-omap-dma" -#else - "?dma?" -#endif - ", " -#ifdef CONFIG_USB_MUSB_OTG - "otg (peripheral+host)" -#elif defined(CONFIG_USB_GADGET_MUSB_HDRC) - "peripheral" -#elif defined(CONFIG_USB_MUSB_HDRC_HCD) - "host" -#endif - ", debug=%d [eps=%d]\n", - debug, - musb->nr_endpoints); - if (code <= 0) - goto done; - count += code; - buffer += code; - -#ifdef CONFIG_USB_GADGET_MUSB_HDRC - code = sprintf(buffer, "Peripheral address: %02x\n", - musb_readb(musb->ctrl_base, MUSB_FADDR)); - if (code <= 0) - goto done; - buffer += code; - count += code; -#endif - -#ifdef CONFIG_USB_MUSB_HDRC_HCD - code = sprintf(buffer, "Root port status: %08x\n", - musb->port1_status); - if (code <= 0) - goto done; - buffer += code; - count += code; -#endif - -#ifdef CONFIG_ARCH_DAVINCI - code = sprintf(buffer, - "DaVinci: ctrl=%02x stat=%1x phy=%03x\n" - "\trndis=%05x auto=%04x intsrc=%08x intmsk=%08x" - "\n", - musb_readl(musb->ctrl_base, DAVINCI_USB_CTRL_REG), - musb_readl(musb->ctrl_base, DAVINCI_USB_STAT_REG), - __raw_readl((void __force __iomem *) - IO_ADDRESS(USBPHY_CTL_PADDR)), - musb_readl(musb->ctrl_base, DAVINCI_RNDIS_REG), - musb_readl(musb->ctrl_base, DAVINCI_AUTOREQ_REG), - musb_readl(musb->ctrl_base, - DAVINCI_USB_INT_SOURCE_REG), - musb_readl(musb->ctrl_base, - DAVINCI_USB_INT_MASK_REG)); - if (code <= 0) - goto done; - count += code; - buffer += code; -#endif /* DAVINCI */ - -#ifdef CONFIG_USB_TUSB6010 - code = sprintf(buffer, - "TUSB6010: devconf %08x, phy enable %08x drive %08x" - "\n\totg %03x timer %08x" - "\n\tprcm conf %08x mgmt %08x; int src %08x mask %08x" - "\n", - musb_readl(musb->ctrl_base, TUSB_DEV_CONF), - musb_readl(musb->ctrl_base, TUSB_PHY_OTG_CTRL_ENABLE), - musb_readl(musb->ctrl_base, TUSB_PHY_OTG_CTRL), - musb_readl(musb->ctrl_base, TUSB_DEV_OTG_STAT), - musb_readl(musb->ctrl_base, TUSB_DEV_OTG_TIMER), - musb_readl(musb->ctrl_base, TUSB_PRCM_CONF), - musb_readl(musb->ctrl_base, TUSB_PRCM_MNGMT), - musb_readl(musb->ctrl_base, TUSB_INT_SRC), - musb_readl(musb->ctrl_base, TUSB_INT_MASK)); - if (code <= 0) - goto done; - count += code; - buffer += code; -#endif /* DAVINCI */ - - if (is_cppi_enabled() && musb->dma_controller) { - code = sprintf(buffer, - "CPPI: txcr=%d txsrc=%01x txena=%01x; " - "rxcr=%d rxsrc=%01x rxena=%01x " - "\n", - musb_readl(musb->ctrl_base, - DAVINCI_TXCPPI_CTRL_REG), - musb_readl(musb->ctrl_base, - DAVINCI_TXCPPI_RAW_REG), - musb_readl(musb->ctrl_base, - DAVINCI_TXCPPI_INTENAB_REG), - musb_readl(musb->ctrl_base, - DAVINCI_RXCPPI_CTRL_REG), - musb_readl(musb->ctrl_base, - DAVINCI_RXCPPI_RAW_REG), - musb_readl(musb->ctrl_base, - DAVINCI_RXCPPI_INTENAB_REG)); - if (code <= 0) - goto done; - count += code; - buffer += code; - } - -#ifdef CONFIG_USB_GADGET_MUSB_HDRC - if (is_peripheral_enabled(musb)) { - code = sprintf(buffer, "Gadget driver: %s\n", - musb->gadget_driver - ? musb->gadget_driver->driver.name - : "(none)"); - if (code <= 0) - goto done; - count += code; - buffer += code; - } -#endif - -done: - return count; -} - -/* Write to ProcFS - * - * C soft-connect - * c soft-disconnect - * I enable HS - * i disable HS - * s stop session - * F force session (OTG-unfriendly) - * E rElinquish bus (OTG) - * H request host mode - * h cancel host request - * T start sending TEST_PACKET - * D set/query the debug level - */ -static int musb_proc_write(struct file *file, const char __user *buffer, - unsigned long count, void *data) -{ - char cmd; - u8 reg; - struct musb *musb = (struct musb *)data; - void __iomem *mbase = musb->mregs; - - /* MOD_INC_USE_COUNT; */ - - if (unlikely(copy_from_user(&cmd, buffer, 1))) - return -EFAULT; - - switch (cmd) { - case 'C': - if (mbase) { - reg = musb_readb(mbase, MUSB_POWER) - | MUSB_POWER_SOFTCONN; - musb_writeb(mbase, MUSB_POWER, reg); - } - break; - - case 'c': - if (mbase) { - reg = musb_readb(mbase, MUSB_POWER) - & ~MUSB_POWER_SOFTCONN; - musb_writeb(mbase, MUSB_POWER, reg); - } - break; - - case 'I': - if (mbase) { - reg = musb_readb(mbase, MUSB_POWER) - | MUSB_POWER_HSENAB; - musb_writeb(mbase, MUSB_POWER, reg); - } - break; - - case 'i': - if (mbase) { - reg = musb_readb(mbase, MUSB_POWER) - & ~MUSB_POWER_HSENAB; - musb_writeb(mbase, MUSB_POWER, reg); - } - break; - - case 'F': - reg = musb_readb(mbase, MUSB_DEVCTL); - reg |= MUSB_DEVCTL_SESSION; - musb_writeb(mbase, MUSB_DEVCTL, reg); - break; - - case 'H': - if (mbase) { - reg = musb_readb(mbase, MUSB_DEVCTL); - reg |= MUSB_DEVCTL_HR; - musb_writeb(mbase, MUSB_DEVCTL, reg); - /* MUSB_HST_MODE( ((struct musb*)data) ); */ - /* WARNING("Host Mode\n"); */ - } - break; - - case 'h': - if (mbase) { - reg = musb_readb(mbase, MUSB_DEVCTL); - reg &= ~MUSB_DEVCTL_HR; - musb_writeb(mbase, MUSB_DEVCTL, reg); - } - break; - - case 'T': - if (mbase) { - musb_load_testpacket(musb); - musb_writeb(mbase, MUSB_TESTMODE, - MUSB_TEST_PACKET); - } - break; - -#if (MUSB_DEBUG > 0) - /* set/read debug level */ - case 'D':{ - if (count > 1) { - char digits[8], *p = digits; - int i = 0, level = 0, sign = 1; - int len = min(count - 1, (unsigned long)8); - - if (copy_from_user(&digits, &buffer[1], len)) - return -EFAULT; - - /* optional sign */ - if (*p == '-') { - len -= 1; - sign = -sign; - p++; - } - - /* read it */ - while (i++ < len && *p > '0' && *p < '9') { - level = level * 10 + (*p - '0'); - p++; - } - - level *= sign; - DBG(1, "debug level %d\n", level); - debug = level; - } - } - break; - - - case '?': - INFO("?: you are seeing it\n"); - INFO("C/c: soft connect enable/disable\n"); - INFO("I/i: hispeed enable/disable\n"); - INFO("F: force session start\n"); - INFO("H: host mode\n"); - INFO("T: start sending TEST_PACKET\n"); - INFO("D: set/read dbug level\n"); - break; -#endif - - default: - ERR("Command %c not implemented\n", cmd); - break; - } - - musb_platform_try_idle(musb, 0); - - return count; -} - -static int musb_proc_read(char *page, char **start, - off_t off, int count, int *eof, void *data) -{ - char *buffer = page; - int code = 0; - unsigned long flags; - struct musb *musb = data; - unsigned epnum; - - count -= off; - count -= 1; /* for NUL at end */ - if (count <= 0) - return -EINVAL; - - spin_lock_irqsave(&musb->lock, flags); - - code = dump_header_stats(musb, buffer); - if (code > 0) { - buffer += code; - count -= code; - } - - /* generate the report for the end points */ - /* REVISIT ... not unless something's connected! */ - for (epnum = 0; count >= 0 && epnum < musb->nr_endpoints; - epnum++) { - code = dump_end_info(musb, epnum, buffer, count); - if (code > 0) { - buffer += code; - count -= code; - } - } - - musb_platform_try_idle(musb, 0); - - spin_unlock_irqrestore(&musb->lock, flags); - *eof = 1; - - return buffer - page; -} - -void __devexit musb_debug_delete(char *name, struct musb *musb) -{ - if (musb->proc_entry) - remove_proc_entry(name, NULL); -} - -struct proc_dir_entry *__init -musb_debug_create(char *name, struct musb *data) -{ - struct proc_dir_entry *pde; - - /* FIXME convert everything to seq_file; then later, debugfs */ - - if (!name) - return NULL; - - pde = create_proc_entry(name, S_IFREG | S_IRUGO | S_IWUSR, NULL); - data->proc_entry = pde; - if (pde) { - pde->data = data; - /* pde->owner = THIS_MODULE; */ - - pde->read_proc = musb_proc_read; - pde->write_proc = musb_proc_write; - - pde->size = 0; - - pr_debug("Registered /proc/%s\n", name); - } else { - pr_debug("Cannot create a valid proc file entry"); - } - - return pde; -} -- GitLab From e8164f64caff68d4e878e1719d88d145faa75f1d Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Sun, 10 Aug 2008 21:22:35 +0300 Subject: [PATCH 686/750] usb: musb: get rid of MUSB_LOGLEVEL and use parameter We can change debugging level on the fly via /sys/module/musb_hdrc/parameters/debug. We can also get rid of the LOGLEVEL facility in Kconfig and rely only in module parameter. Cc: Anand Gadiyar Cc: Bryan Wu Cc: David Brownell Signed-off-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman --- drivers/usb/musb/Kconfig | 13 ++++++------- drivers/usb/musb/Makefile | 16 ++-------------- drivers/usb/musb/musb_core.c | 17 ++++------------- drivers/usb/musb/musb_debug.h | 4 ---- 4 files changed, 12 insertions(+), 38 deletions(-) diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig index faca4333f27..a0017486ad4 100644 --- a/drivers/usb/musb/Kconfig +++ b/drivers/usb/musb/Kconfig @@ -165,12 +165,11 @@ config USB_TUSB_OMAP_DMA help Enable DMA transfers on TUSB 6010 when OMAP DMA is available. -config USB_MUSB_LOGLEVEL +config USB_MUSB_DEBUG depends on USB_MUSB_HDRC - int 'Logging Level (0 - none / 3 - annoying / ... )' - default 0 + bool "Enable debugging messages" + default n help - Set the logging level. 0 disables the debugging altogether, - although when USB_DEBUG is set the value is at least 1. - Starting at level 3, per-transfer (urb, usb_request, packet, - or dma transfer) tracing may kick in. + This enables musb debugging. To set the logging level use the debug + module parameter. Starting at level 3, per-transfer (urb, usb_request, + packet, or dma transfer) tracing may kick in. diff --git a/drivers/usb/musb/Makefile b/drivers/usb/musb/Makefile index 860369c7cbe..b6af0d687a7 100644 --- a/drivers/usb/musb/Makefile +++ b/drivers/usb/musb/Makefile @@ -64,18 +64,6 @@ endif # Debugging -MUSB_DEBUG:=$(CONFIG_USB_MUSB_LOGLEVEL) - -ifeq ("$(strip $(MUSB_DEBUG))","") - ifdef CONFIG_USB_DEBUG - MUSB_DEBUG:=1 - else - MUSB_DEBUG:=0 - endif +ifeq ($(CONFIG_USB_MUSB_DEBUG),y) + EXTRA_CFLAGS += -DDEBUG endif - -ifneq ($(MUSB_DEBUG),0) - EXTRA_CFLAGS += -DDEBUG -endif - -EXTRA_CFLAGS += -DMUSB_DEBUG=$(MUSB_DEBUG) diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c index 99690ba436d..c5b8f0296fc 100644 --- a/drivers/usb/musb/musb_core.c +++ b/drivers/usb/musb/musb_core.c @@ -114,23 +114,14 @@ -#if MUSB_DEBUG > 0 -unsigned debug = MUSB_DEBUG; -module_param(debug, uint, 0); -MODULE_PARM_DESC(debug, "initial debug message level"); - -#define MUSB_VERSION_SUFFIX "/dbg" -#endif +unsigned debug; +module_param(debug, uint, S_IRUGO | S_IWUSR); +MODULE_PARM_DESC(debug, "Debug message level. Default = 0"); #define DRIVER_AUTHOR "Mentor Graphics, Texas Instruments, Nokia" #define DRIVER_DESC "Inventra Dual-Role USB Controller Driver" -#define MUSB_VERSION_BASE "6.0" - -#ifndef MUSB_VERSION_SUFFIX -#define MUSB_VERSION_SUFFIX "" -#endif -#define MUSB_VERSION MUSB_VERSION_BASE MUSB_VERSION_SUFFIX +#define MUSB_VERSION "6.0" #define DRIVER_INFO DRIVER_DESC ", v" MUSB_VERSION diff --git a/drivers/usb/musb/musb_debug.h b/drivers/usb/musb/musb_debug.h index 3bdb311e820..4d2794441b1 100644 --- a/drivers/usb/musb/musb_debug.h +++ b/drivers/usb/musb/musb_debug.h @@ -48,11 +48,7 @@ __func__, __LINE__ , ## args); \ } } while (0) -#if MUSB_DEBUG > 0 extern unsigned debug; -#else -#define debug 0 -#endif static inline int _dbg_level(unsigned l) { -- GitLab From fb85d991616046f1b640ed9c4eab9b44908dab74 Mon Sep 17 00:00:00 2001 From: Anand Gadiyar Date: Thu, 21 Aug 2008 20:21:00 +0530 Subject: [PATCH 687/750] MUSB: Fix index register corruption seen with g_ether and Windows host If Indexed Mode register accesses are enabled, the ep0_rxstate() function calls musb_g_ep0_giveback() before writing to the CSR register. When control returns to this ep0_rxstate, the index register contents are over-written. This causes the CSR register write to fail. Fixed by writing the correct value into the index register before writing to the CSR. This was observed only in ep0_rxstate() with g_ether loaded and the device connected to a MS Windows host PC. Anticipatively fixed ep0_txstate() as well. Signed-off-by: Anand Gadiyar Acked-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman --- drivers/usb/musb/musb_gadget_ep0.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/musb/musb_gadget_ep0.c b/drivers/usb/musb/musb_gadget_ep0.c index 48d7d3ccb24..a57652fff39 100644 --- a/drivers/usb/musb/musb_gadget_ep0.c +++ b/drivers/usb/musb/musb_gadget_ep0.c @@ -476,6 +476,7 @@ static void ep0_rxstate(struct musb *musb) return; musb->ackpend = 0; } + musb_ep_select(musb->mregs, 0); musb_writew(regs, MUSB_CSR0, tmp); } @@ -528,6 +529,7 @@ static void ep0_txstate(struct musb *musb) } /* send it out, triggering a "txpktrdy cleared" irq */ + musb_ep_select(musb->mregs, 0); musb_writew(regs, MUSB_CSR0, csr); } -- GitLab From 74573ee7096a4ffc2f098108d21c85801b9c7434 Mon Sep 17 00:00:00 2001 From: Alexey Dobriyan Date: Wed, 20 Aug 2008 16:56:04 -0700 Subject: [PATCH 688/750] USB: cdc-acm: don't unlock acm->mutex on error path On Wed, Jul 23, 2008 at 03:52:36PM +0300, Andrei Popa wrote: > I installed gnokii-0.6.22-r2 and gave the command "gnokii --identify" > and the kernel oopsed: > > BUG: unable to handle kernel NULL pointer dereference at 00000458 > IP: [] mutex_unlock+0x0/0xb > [] acm_tty_open+0x4c/0x214 Signed-off-by: Alexey Dobriyan Tested-by: Andrei Popa Cc: stable [2.6.25.x, 2.6.26.x] Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman --- drivers/usb/class/cdc-acm.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index 382522eb1f7..c257453fa9d 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -589,8 +589,8 @@ static int acm_tty_open(struct tty_struct *tty, struct file *filp) tasklet_schedule(&acm->urb_task); done: -err_out: mutex_unlock(&acm->mutex); +err_out: mutex_unlock(&open_mutex); return rv; -- GitLab From 65605ae8e587d714f73e674369bc4cd5a1e53a9b Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Tue, 12 Aug 2008 14:33:27 -0400 Subject: [PATCH 689/750] USB: Add udev argument to interface suspend/resume functions This patch (as1127) makes a minor change to the prototypes of the usb_suspend_interface() and usb_resume_interface() routines. Now the usb_device structure is passed as an argument, instead of being computed on-the-fly from the usb_interface argument. It makes the code look simpler, even if it really isn't much different from before. Signed-off-by: Alan Stern Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/driver.c | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c index 2be37fe466f..ed1cc8530a9 100644 --- a/drivers/usb/core/driver.c +++ b/drivers/usb/core/driver.c @@ -926,14 +926,14 @@ static int usb_resume_device(struct usb_device *udev) } /* Caller has locked intf's usb_device's pm mutex */ -static int usb_suspend_interface(struct usb_interface *intf, pm_message_t msg) +static int usb_suspend_interface(struct usb_device *udev, + struct usb_interface *intf, pm_message_t msg) { struct usb_driver *driver; int status = 0; /* with no hardware, USB interfaces only use FREEZE and ON states */ - if (interface_to_usbdev(intf)->state == USB_STATE_NOTATTACHED || - !is_active(intf)) + if (udev->state == USB_STATE_NOTATTACHED || !is_active(intf)) goto done; if (intf->condition == USB_INTERFACE_UNBOUND) /* This can't happen */ @@ -944,7 +944,7 @@ static int usb_suspend_interface(struct usb_interface *intf, pm_message_t msg) status = driver->suspend(intf, msg); if (status == 0) mark_quiesced(intf); - else if (!interface_to_usbdev(intf)->auto_pm) + else if (!udev->auto_pm) dev_err(&intf->dev, "%s error %d\n", "suspend", status); } else { @@ -961,13 +961,13 @@ static int usb_suspend_interface(struct usb_interface *intf, pm_message_t msg) } /* Caller has locked intf's usb_device's pm_mutex */ -static int usb_resume_interface(struct usb_interface *intf, int reset_resume) +static int usb_resume_interface(struct usb_device *udev, + struct usb_interface *intf, int reset_resume) { struct usb_driver *driver; int status = 0; - if (interface_to_usbdev(intf)->state == USB_STATE_NOTATTACHED || - is_active(intf)) + if (udev->state == USB_STATE_NOTATTACHED || is_active(intf)) goto done; /* Don't let autoresume interfere with unbinding */ @@ -1151,7 +1151,7 @@ static int usb_suspend_both(struct usb_device *udev, pm_message_t msg) if (udev->actconfig) { for (; i < udev->actconfig->desc.bNumInterfaces; i++) { intf = udev->actconfig->interface[i]; - status = usb_suspend_interface(intf, msg); + status = usb_suspend_interface(udev, intf, msg); if (status != 0) break; } @@ -1163,7 +1163,7 @@ static int usb_suspend_both(struct usb_device *udev, pm_message_t msg) if (status != 0) { while (--i >= 0) { intf = udev->actconfig->interface[i]; - usb_resume_interface(intf, 0); + usb_resume_interface(udev, intf, 0); } /* Try another autosuspend when the interfaces aren't busy */ @@ -1276,7 +1276,7 @@ static int usb_resume_both(struct usb_device *udev) if (status == 0 && udev->actconfig) { for (i = 0; i < udev->actconfig->desc.bNumInterfaces; i++) { intf = udev->actconfig->interface[i]; - usb_resume_interface(intf, udev->reset_resume); + usb_resume_interface(udev, intf, udev->reset_resume); } } -- GitLab From 55151d7daba185f94e9dc561a5a2ba36b5f647dd Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Tue, 12 Aug 2008 14:33:59 -0400 Subject: [PATCH 690/750] USB: Defer Set-Interface for suspended devices This patch (as1128) fixes one of the problems related to the new PM infrastructure. We are not allowed to register new child devices during the middle of a system sleep transition, but unbinding a USB driver causes the core to automatically install altsetting 0 and thereby create new endpoint pseudo-devices. The patch fixes this problem (and the related problem that installing altsetting 0 will fail if the device is suspended) by deferring the Set-Interface call until some later time when it is legal and can succeed. Possible later times are: when a new driver is being probed for the interface, and when the interface is being resumed. Signed-off-by: Alan Stern Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/driver.c | 31 ++++++++++++++++++++++++++++--- include/linux/usb.h | 3 +++ 2 files changed, 31 insertions(+), 3 deletions(-) diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c index ed1cc8530a9..637b2bea556 100644 --- a/drivers/usb/core/driver.c +++ b/drivers/usb/core/driver.c @@ -230,6 +230,13 @@ static int usb_probe_interface(struct device *dev) */ intf->pm_usage_cnt = !(driver->supports_autosuspend); + /* Carry out a deferred switch to altsetting 0 */ + if (intf->needs_altsetting0) { + usb_set_interface(udev, intf->altsetting[0]. + desc.bInterfaceNumber, 0); + intf->needs_altsetting0 = 0; + } + error = driver->probe(intf, id); if (error) { mark_quiesced(intf); @@ -266,8 +273,17 @@ static int usb_unbind_interface(struct device *dev) driver->disconnect(intf); - /* reset other interface state */ - usb_set_interface(udev, intf->altsetting[0].desc.bInterfaceNumber, 0); + /* Reset other interface state. + * We cannot do a Set-Interface if the device is suspended or + * if it is prepared for a system sleep (since installing a new + * altsetting means creating new endpoint device entries). + * When either of these happens, defer the Set-Interface. + */ + if (!error && intf->dev.power.status == DPM_ON) + usb_set_interface(udev, intf->altsetting[0]. + desc.bInterfaceNumber, 0); + else + intf->needs_altsetting0 = 1; usb_set_intfdata(intf, NULL); intf->condition = USB_INTERFACE_UNBOUND; @@ -975,8 +991,17 @@ static int usb_resume_interface(struct usb_device *udev, goto done; /* Can't resume it if it doesn't have a driver. */ - if (intf->condition == USB_INTERFACE_UNBOUND) + if (intf->condition == USB_INTERFACE_UNBOUND) { + + /* Carry out a deferred switch to altsetting 0 */ + if (intf->needs_altsetting0 && + intf->dev.power.status == DPM_ON) { + usb_set_interface(udev, intf->altsetting[0]. + desc.bInterfaceNumber, 0); + intf->needs_altsetting0 = 0; + } goto done; + } /* Don't resume if the interface is marked for rebinding */ if (intf->needs_binding) diff --git a/include/linux/usb.h b/include/linux/usb.h index 0924cd9c30f..94ac74aba6b 100644 --- a/include/linux/usb.h +++ b/include/linux/usb.h @@ -110,6 +110,8 @@ enum usb_interface_condition { * @sysfs_files_created: sysfs attributes exist * @needs_remote_wakeup: flag set when the driver requires remote-wakeup * capability during autosuspend. + * @needs_altsetting0: flag set when a set-interface request for altsetting 0 + * has been deferred. * @needs_binding: flag set when the driver should be re-probed or unbound * following a reset or suspend operation it doesn't support. * @dev: driver model's view of this device @@ -162,6 +164,7 @@ struct usb_interface { unsigned is_active:1; /* the interface is not suspended */ unsigned sysfs_files_created:1; /* the sysfs attributes exist */ unsigned needs_remote_wakeup:1; /* driver requires remote wakeup */ + unsigned needs_altsetting0:1; /* switch to altsetting 0 is pending */ unsigned needs_binding:1; /* needs delayed unbind/rebind */ struct device dev; /* interface specific device info */ -- GitLab From f2189c477c986db47ac7f9cc32d05f6df18bfe9e Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Tue, 12 Aug 2008 14:34:10 -0400 Subject: [PATCH 691/750] USB: Add new PM callback methods for USB This patch (as1129) adds support for the new PM callbacks to usbcore. The new callbacks merely invoke the same old USB power management routines as the old ones did. A minor improvement is that the callbacks are present only in the "USB-device" device_type structure, rather than in the bus_type structure. This way they will be invoked only for USB devices, not for USB interfaces. The core USB PM routines automatically handle suspending and resuming interfaces along with their devices. Signed-off-by: Alan Stern Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/driver.c | 15 ++------ drivers/usb/core/usb.c | 73 +++++++++++++++++++++++++++++++++++---- drivers/usb/core/usb.h | 3 ++ 3 files changed, 72 insertions(+), 19 deletions(-) diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c index 637b2bea556..2da70b4d33f 100644 --- a/drivers/usb/core/driver.c +++ b/drivers/usb/core/driver.c @@ -1630,12 +1630,10 @@ int usb_external_resume_device(struct usb_device *udev) return status; } -static int usb_suspend(struct device *dev, pm_message_t message) +int usb_suspend(struct device *dev, pm_message_t message) { struct usb_device *udev; - if (!is_usb_device(dev)) /* Ignore PM for interfaces */ - return 0; udev = to_usb_device(dev); /* If udev is already suspended, we can skip this suspend and @@ -1654,12 +1652,10 @@ static int usb_suspend(struct device *dev, pm_message_t message) return usb_external_suspend_device(udev, message); } -static int usb_resume(struct device *dev) +int usb_resume(struct device *dev) { struct usb_device *udev; - if (!is_usb_device(dev)) /* Ignore PM for interfaces */ - return 0; udev = to_usb_device(dev); /* If udev->skip_sys_resume is set then udev was already suspended @@ -1671,17 +1667,10 @@ static int usb_resume(struct device *dev) return usb_external_resume_device(udev); } -#else - -#define usb_suspend NULL -#define usb_resume NULL - #endif /* CONFIG_PM */ struct bus_type usb_bus_type = { .name = "usb", .match = usb_device_match, .uevent = usb_uevent, - .suspend = usb_suspend, - .resume = usb_resume, }; diff --git a/drivers/usb/core/usb.c b/drivers/usb/core/usb.c index 84fcaa6a21e..be1fa0723f2 100644 --- a/drivers/usb/core/usb.c +++ b/drivers/usb/core/usb.c @@ -219,12 +219,6 @@ static int usb_dev_uevent(struct device *dev, struct kobj_uevent_env *env) } #endif /* CONFIG_HOTPLUG */ -struct device_type usb_device_type = { - .name = "usb_device", - .release = usb_release_dev, - .uevent = usb_dev_uevent, -}; - #ifdef CONFIG_PM static int ksuspend_usb_init(void) @@ -244,13 +238,80 @@ static void ksuspend_usb_cleanup(void) destroy_workqueue(ksuspend_usb_wq); } +/* USB device Power-Management thunks. + * There's no need to distinguish here between quiescing a USB device + * and powering it down; the generic_suspend() routine takes care of + * it by skipping the usb_port_suspend() call for a quiesce. And for + * USB interfaces there's no difference at all. + */ + +static int usb_dev_prepare(struct device *dev) +{ + return 0; /* Implement eventually? */ +} + +static void usb_dev_complete(struct device *dev) +{ + /* Currently used only for rebinding interfaces */ + usb_resume(dev); /* Implement eventually? */ +} + +static int usb_dev_suspend(struct device *dev) +{ + return usb_suspend(dev, PMSG_SUSPEND); +} + +static int usb_dev_resume(struct device *dev) +{ + return usb_resume(dev); +} + +static int usb_dev_freeze(struct device *dev) +{ + return usb_suspend(dev, PMSG_FREEZE); +} + +static int usb_dev_thaw(struct device *dev) +{ + return usb_resume(dev); +} + +static int usb_dev_poweroff(struct device *dev) +{ + return usb_suspend(dev, PMSG_HIBERNATE); +} + +static int usb_dev_restore(struct device *dev) +{ + return usb_resume(dev); +} + +static struct pm_ops usb_device_pm_ops = { + .prepare = usb_dev_prepare, + .complete = usb_dev_complete, + .suspend = usb_dev_suspend, + .resume = usb_dev_resume, + .freeze = usb_dev_freeze, + .thaw = usb_dev_thaw, + .poweroff = usb_dev_poweroff, + .restore = usb_dev_restore, +}; + #else #define ksuspend_usb_init() 0 #define ksuspend_usb_cleanup() do {} while (0) +#define usb_device_pm_ops (*(struct pm_ops *)0) #endif /* CONFIG_PM */ +struct device_type usb_device_type = { + .name = "usb_device", + .release = usb_release_dev, + .uevent = usb_dev_uevent, + .pm = &usb_device_pm_ops, +}; + /* Returns 1 if @usb_bus is WUSB, 0 otherwise */ static unsigned usb_bus_is_wusb(struct usb_bus *bus) diff --git a/drivers/usb/core/usb.h b/drivers/usb/core/usb.h index d9a6e16dbf8..9a1a45ac3ad 100644 --- a/drivers/usb/core/usb.h +++ b/drivers/usb/core/usb.h @@ -41,6 +41,9 @@ extern void usb_host_cleanup(void); #ifdef CONFIG_PM +extern int usb_suspend(struct device *dev, pm_message_t msg); +extern int usb_resume(struct device *dev); + extern void usb_autosuspend_work(struct work_struct *work); extern int usb_port_suspend(struct usb_device *dev); extern int usb_port_resume(struct usb_device *dev); -- GitLab From 5096aedcd2eb70fbea83f09281f97f9ec973d9de Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Tue, 12 Aug 2008 14:34:14 -0400 Subject: [PATCH 692/750] USB: Don't rebind before "complete" callback This patch (as1130) fixes an incompatibility between the new PM infrastructure and USB power management. We are not allowed to call drivers' probe routines during a system sleep transition between the "prepare" and "complete" callbacks, but that's exactly what we do when a driver doesn't have full suspend/resume support. Such drivers are unbound during the "suspend" call and reprobed during the "resume" call. The patch causes the reprobe step to be skipped if the "complete" callback hasn't been issued yet, i.e., if the interface's dev.power.status field is not equal to DPM_ON. Thus during the "resume" callback nothing bad will happen, and during the final "complete" callback the reprobing will occur as desired. This fixes the problem reported in Bugzilla #11263. Signed-off-by: Alan Stern Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/driver.c | 30 +++++++++--------------------- 1 file changed, 9 insertions(+), 21 deletions(-) diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c index 2da70b4d33f..5a7fa6f0995 100644 --- a/drivers/usb/core/driver.c +++ b/drivers/usb/core/driver.c @@ -814,7 +814,8 @@ void usb_forced_unbind_intf(struct usb_interface *intf) * The caller must hold @intf's device's lock, but not its pm_mutex * and not @intf->dev.sem. * - * FIXME: The caller must block system sleep transitions. + * Note: Rebinds will be skipped if a system sleep transition is in + * progress and the PM "complete" callback hasn't occurred yet. */ void usb_rebind_intf(struct usb_interface *intf) { @@ -830,10 +831,12 @@ void usb_rebind_intf(struct usb_interface *intf) } /* Try to rebind the interface */ - intf->needs_binding = 0; - rc = device_attach(&intf->dev); - if (rc < 0) - dev_warn(&intf->dev, "rebind failed: %d\n", rc); + if (intf->dev.power.status == DPM_ON) { + intf->needs_binding = 0; + rc = device_attach(&intf->dev); + if (rc < 0) + dev_warn(&intf->dev, "rebind failed: %d\n", rc); + } } #ifdef CONFIG_PM @@ -845,7 +848,6 @@ void usb_rebind_intf(struct usb_interface *intf) * or rebind interfaces that have been unbound, according to @action. * * The caller must hold @udev's device lock. - * FIXME: For rebinds, the caller must block system sleep transitions. */ static void do_unbind_rebind(struct usb_device *udev, int action) { @@ -867,22 +869,8 @@ static void do_unbind_rebind(struct usb_device *udev, int action) } break; case DO_REBIND: - if (intf->needs_binding) { - - /* FIXME: The next line is needed because we are going to probe - * the interface, but as far as the PM core is concerned the - * interface is still suspended. The problem wouldn't exist - * if we could rebind the interface during the interface's own - * resume() call, but at the time the usb_device isn't locked! - * - * The real solution will be to carry this out during the device's - * complete() callback. Until that is implemented, we have to - * use this hack. - */ -// intf->dev.power.sleeping = 0; - + if (intf->needs_binding) usb_rebind_intf(intf); - } break; } } -- GitLab From b5fb454f69642f9d933b327b185a2ba06dd0945c Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Wed, 20 Aug 2008 17:22:05 -0400 Subject: [PATCH 693/750] USB: automatically enable RHSC interrupts This patch (as1069c) changes the way OHCI root-hub status-change interrupts are enabled. Currently a special HCD method, hub_irq_enable(), is called when the hub driver is finished using a root hub. This approach turns out to be subject to races, resulting in unnecessary polling. The patch does away with the method entirely. Instead, the driver automatically enables the RHSC interrupt when no more status changes are present. This scheme is safe with controllers using level-triggered semantics for their interrupt flags. Signed-off-by: Alan Stern Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/hcd.c | 9 ------ drivers/usb/core/hcd.h | 4 --- drivers/usb/core/hub.c | 9 ------ drivers/usb/host/ohci-at91.c | 1 - drivers/usb/host/ohci-au1xxx.c | 1 - drivers/usb/host/ohci-ep93xx.c | 1 - drivers/usb/host/ohci-hub.c | 53 +++++++++++++++++++-------------- drivers/usb/host/ohci-lh7a404.c | 1 - drivers/usb/host/ohci-omap.c | 1 - drivers/usb/host/ohci-pci.c | 1 - drivers/usb/host/ohci-pnx4008.c | 1 - drivers/usb/host/ohci-pnx8550.c | 1 - drivers/usb/host/ohci-ppc-of.c | 1 - drivers/usb/host/ohci-ppc-soc.c | 1 - drivers/usb/host/ohci-ps3.c | 1 - drivers/usb/host/ohci-pxa27x.c | 1 - drivers/usb/host/ohci-s3c2410.c | 1 - drivers/usb/host/ohci-sa1111.c | 1 - drivers/usb/host/ohci-sh.c | 1 - drivers/usb/host/ohci-sm501.c | 1 - drivers/usb/host/ohci-ssb.c | 1 - drivers/usb/host/u132-hcd.c | 11 ------- 22 files changed, 31 insertions(+), 72 deletions(-) diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c index f7bfd72ef11..8abd4e59bf4 100644 --- a/drivers/usb/core/hcd.c +++ b/drivers/usb/core/hcd.c @@ -924,15 +924,6 @@ static int register_root_hub(struct usb_hcd *hcd) return retval; } -void usb_enable_root_hub_irq (struct usb_bus *bus) -{ - struct usb_hcd *hcd; - - hcd = container_of (bus, struct usb_hcd, self); - if (hcd->driver->hub_irq_enable && hcd->state != HC_STATE_HALT) - hcd->driver->hub_irq_enable (hcd); -} - /*-------------------------------------------------------------------------*/ diff --git a/drivers/usb/core/hcd.h b/drivers/usb/core/hcd.h index 5b0b59b0d89..e710ce04e22 100644 --- a/drivers/usb/core/hcd.h +++ b/drivers/usb/core/hcd.h @@ -212,8 +212,6 @@ struct hc_driver { int (*bus_suspend)(struct usb_hcd *); int (*bus_resume)(struct usb_hcd *); int (*start_port_reset)(struct usb_hcd *, unsigned port_num); - void (*hub_irq_enable)(struct usb_hcd *); - /* Needed only if port-change IRQs are level-triggered */ /* force handover of high-speed port to full-speed companion */ void (*relinquish_port)(struct usb_hcd *, int); @@ -379,8 +377,6 @@ extern struct list_head usb_bus_list; extern struct mutex usb_bus_list_lock; extern wait_queue_head_t usb_kill_urb_queue; -extern void usb_enable_root_hub_irq(struct usb_bus *bus); - extern int usb_find_interface_driver(struct usb_device *dev, struct usb_interface *interface); diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index 107e1d25dde..6a5cb018383 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -2102,8 +2102,6 @@ int usb_port_resume(struct usb_device *udev) } clear_bit(port1, hub->busy_bits); - if (!hub->hdev->parent && !hub->busy_bits[0]) - usb_enable_root_hub_irq(hub->hdev->bus); status = check_port_resume_type(udev, hub, port1, status, portchange, portstatus); @@ -3081,11 +3079,6 @@ static void hub_events(void) } } - /* If this is a root hub, tell the HCD it's okay to - * re-enable port-change interrupts now. */ - if (!hdev->parent && !hub->busy_bits[0]) - usb_enable_root_hub_irq(hdev->bus); - loop_autopm: /* Allow autosuspend if we're not going to run again */ if (list_empty(&hub->event_list)) @@ -3311,8 +3304,6 @@ static int usb_reset_and_verify_device(struct usb_device *udev) break; } clear_bit(port1, parent_hub->busy_bits); - if (!parent_hdev->parent && !parent_hub->busy_bits[0]) - usb_enable_root_hub_irq(parent_hdev->bus); if (ret < 0) goto re_enumerate; diff --git a/drivers/usb/host/ohci-at91.c b/drivers/usb/host/ohci-at91.c index 6db7a2889e6..4ed228a8994 100644 --- a/drivers/usb/host/ohci-at91.c +++ b/drivers/usb/host/ohci-at91.c @@ -260,7 +260,6 @@ static const struct hc_driver ohci_at91_hc_driver = { */ .hub_status_data = ohci_hub_status_data, .hub_control = ohci_hub_control, - .hub_irq_enable = ohci_rhsc_enable, #ifdef CONFIG_PM .bus_suspend = ohci_bus_suspend, .bus_resume = ohci_bus_resume, diff --git a/drivers/usb/host/ohci-au1xxx.c b/drivers/usb/host/ohci-au1xxx.c index c0948008fe3..2ac4e022a13 100644 --- a/drivers/usb/host/ohci-au1xxx.c +++ b/drivers/usb/host/ohci-au1xxx.c @@ -163,7 +163,6 @@ static const struct hc_driver ohci_au1xxx_hc_driver = { */ .hub_status_data = ohci_hub_status_data, .hub_control = ohci_hub_control, - .hub_irq_enable = ohci_rhsc_enable, #ifdef CONFIG_PM .bus_suspend = ohci_bus_suspend, .bus_resume = ohci_bus_resume, diff --git a/drivers/usb/host/ohci-ep93xx.c b/drivers/usb/host/ohci-ep93xx.c index cb0b506f825..fb3055f084b 100644 --- a/drivers/usb/host/ohci-ep93xx.c +++ b/drivers/usb/host/ohci-ep93xx.c @@ -134,7 +134,6 @@ static struct hc_driver ohci_ep93xx_hc_driver = { .get_frame_number = ohci_get_frame, .hub_status_data = ohci_hub_status_data, .hub_control = ohci_hub_control, - .hub_irq_enable = ohci_rhsc_enable, #ifdef CONFIG_PM .bus_suspend = ohci_bus_suspend, .bus_resume = ohci_bus_resume, diff --git a/drivers/usb/host/ohci-hub.c b/drivers/usb/host/ohci-hub.c index 439beb784f3..7ea9a7b3115 100644 --- a/drivers/usb/host/ohci-hub.c +++ b/drivers/usb/host/ohci-hub.c @@ -36,18 +36,6 @@ /*-------------------------------------------------------------------------*/ -/* hcd->hub_irq_enable() */ -static void ohci_rhsc_enable (struct usb_hcd *hcd) -{ - struct ohci_hcd *ohci = hcd_to_ohci (hcd); - - spin_lock_irq(&ohci->lock); - if (!ohci->autostop) - del_timer(&hcd->rh_timer); /* Prevent next poll */ - ohci_writel(ohci, OHCI_INTR_RHSC, &ohci->regs->intrenable); - spin_unlock_irq(&ohci->lock); -} - #define OHCI_SCHED_ENABLES \ (OHCI_CTRL_CLE|OHCI_CTRL_BLE|OHCI_CTRL_PLE|OHCI_CTRL_IE) @@ -374,18 +362,28 @@ static int ohci_root_hub_state_changes(struct ohci_hcd *ohci, int changed, int any_connected) { int poll_rh = 1; + int rhsc; + rhsc = ohci_readl(ohci, &ohci->regs->intrenable) & OHCI_INTR_RHSC; switch (ohci->hc_control & OHCI_CTRL_HCFS) { case OHCI_USB_OPER: - /* keep on polling until we know a device is connected - * and RHSC is enabled */ + /* If no status changes are pending, enable status-change + * interrupts. + */ + if (!rhsc && !changed) { + rhsc = OHCI_INTR_RHSC; + ohci_writel(ohci, rhsc, &ohci->regs->intrenable); + } + + /* Keep on polling until we know a device is connected + * and RHSC is enabled, or until we autostop. + */ if (!ohci->autostop) { if (any_connected || !device_may_wakeup(&ohci_to_hcd(ohci) ->self.root_hub->dev)) { - if (ohci_readl(ohci, &ohci->regs->intrenable) & - OHCI_INTR_RHSC) + if (rhsc) poll_rh = 0; } else { ohci->autostop = 1; @@ -398,12 +396,13 @@ static int ohci_root_hub_state_changes(struct ohci_hcd *ohci, int changed, ohci->autostop = 0; ohci->next_statechange = jiffies + STATECHANGE_DELAY; - } else if (time_after_eq(jiffies, + } else if (rhsc && time_after_eq(jiffies, ohci->next_statechange) && !ohci->ed_rm_list && !(ohci->hc_control & OHCI_SCHED_ENABLES)) { ohci_rh_suspend(ohci, 1); + poll_rh = 0; } } break; @@ -417,6 +416,12 @@ static int ohci_root_hub_state_changes(struct ohci_hcd *ohci, int changed, else usb_hcd_resume_root_hub(ohci_to_hcd(ohci)); } else { + if (!rhsc && (ohci->autostop || + ohci_to_hcd(ohci)->self.root_hub-> + do_remote_wakeup)) + ohci_writel(ohci, OHCI_INTR_RHSC, + &ohci->regs->intrenable); + /* everything is idle, no need for polling */ poll_rh = 0; } @@ -438,12 +443,16 @@ static inline int ohci_rh_resume(struct ohci_hcd *ohci) static int ohci_root_hub_state_changes(struct ohci_hcd *ohci, int changed, int any_connected) { - int poll_rh = 1; - - /* keep on polling until RHSC is enabled */ + /* If RHSC is enabled, don't poll */ if (ohci_readl(ohci, &ohci->regs->intrenable) & OHCI_INTR_RHSC) - poll_rh = 0; - return poll_rh; + return 0; + + /* If no status changes are pending, enable status-change interrupts */ + if (!changed) { + ohci_writel(ohci, OHCI_INTR_RHSC, &ohci->regs->intrenable); + return 0; + } + return 1; } #endif /* CONFIG_PM */ diff --git a/drivers/usb/host/ohci-lh7a404.c b/drivers/usb/host/ohci-lh7a404.c index 9e31d440d11..de42283149c 100644 --- a/drivers/usb/host/ohci-lh7a404.c +++ b/drivers/usb/host/ohci-lh7a404.c @@ -193,7 +193,6 @@ static const struct hc_driver ohci_lh7a404_hc_driver = { */ .hub_status_data = ohci_hub_status_data, .hub_control = ohci_hub_control, - .hub_irq_enable = ohci_rhsc_enable, #ifdef CONFIG_PM .bus_suspend = ohci_bus_suspend, .bus_resume = ohci_bus_resume, diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c index 3d532b70967..1eb64d08b60 100644 --- a/drivers/usb/host/ohci-omap.c +++ b/drivers/usb/host/ohci-omap.c @@ -470,7 +470,6 @@ static const struct hc_driver ohci_omap_hc_driver = { */ .hub_status_data = ohci_hub_status_data, .hub_control = ohci_hub_control, - .hub_irq_enable = ohci_rhsc_enable, #ifdef CONFIG_PM .bus_suspend = ohci_bus_suspend, .bus_resume = ohci_bus_resume, diff --git a/drivers/usb/host/ohci-pci.c b/drivers/usb/host/ohci-pci.c index 083e8df0a81..a9c2ae36c7a 100644 --- a/drivers/usb/host/ohci-pci.c +++ b/drivers/usb/host/ohci-pci.c @@ -459,7 +459,6 @@ static const struct hc_driver ohci_pci_hc_driver = { */ .hub_status_data = ohci_hub_status_data, .hub_control = ohci_hub_control, - .hub_irq_enable = ohci_rhsc_enable, #ifdef CONFIG_PM .bus_suspend = ohci_bus_suspend, .bus_resume = ohci_bus_resume, diff --git a/drivers/usb/host/ohci-pnx4008.c b/drivers/usb/host/ohci-pnx4008.c index b02cd076197..658a2a978c3 100644 --- a/drivers/usb/host/ohci-pnx4008.c +++ b/drivers/usb/host/ohci-pnx4008.c @@ -277,7 +277,6 @@ static const struct hc_driver ohci_pnx4008_hc_driver = { */ .hub_status_data = ohci_hub_status_data, .hub_control = ohci_hub_control, - .hub_irq_enable = ohci_rhsc_enable, #ifdef CONFIG_PM .bus_suspend = ohci_bus_suspend, .bus_resume = ohci_bus_resume, diff --git a/drivers/usb/host/ohci-pnx8550.c b/drivers/usb/host/ohci-pnx8550.c index 605d59cba28..28467e288a9 100644 --- a/drivers/usb/host/ohci-pnx8550.c +++ b/drivers/usb/host/ohci-pnx8550.c @@ -201,7 +201,6 @@ static const struct hc_driver ohci_pnx8550_hc_driver = { */ .hub_status_data = ohci_hub_status_data, .hub_control = ohci_hub_control, - .hub_irq_enable = ohci_rhsc_enable, #ifdef CONFIG_PM .bus_suspend = ohci_bus_suspend, .bus_resume = ohci_bus_resume, diff --git a/drivers/usb/host/ohci-ppc-of.c b/drivers/usb/host/ohci-ppc-of.c index 91e6e101a4c..7ac53264ead 100644 --- a/drivers/usb/host/ohci-ppc-of.c +++ b/drivers/usb/host/ohci-ppc-of.c @@ -72,7 +72,6 @@ static const struct hc_driver ohci_ppc_of_hc_driver = { */ .hub_status_data = ohci_hub_status_data, .hub_control = ohci_hub_control, - .hub_irq_enable = ohci_rhsc_enable, #ifdef CONFIG_PM .bus_suspend = ohci_bus_suspend, .bus_resume = ohci_bus_resume, diff --git a/drivers/usb/host/ohci-ppc-soc.c b/drivers/usb/host/ohci-ppc-soc.c index 523c3012557..cd3398b675b 100644 --- a/drivers/usb/host/ohci-ppc-soc.c +++ b/drivers/usb/host/ohci-ppc-soc.c @@ -172,7 +172,6 @@ static const struct hc_driver ohci_ppc_soc_hc_driver = { */ .hub_status_data = ohci_hub_status_data, .hub_control = ohci_hub_control, - .hub_irq_enable = ohci_rhsc_enable, #ifdef CONFIG_PM .bus_suspend = ohci_bus_suspend, .bus_resume = ohci_bus_resume, diff --git a/drivers/usb/host/ohci-ps3.c b/drivers/usb/host/ohci-ps3.c index 55c95647f00..2089d8a46c4 100644 --- a/drivers/usb/host/ohci-ps3.c +++ b/drivers/usb/host/ohci-ps3.c @@ -68,7 +68,6 @@ static const struct hc_driver ps3_ohci_hc_driver = { .get_frame_number = ohci_get_frame, .hub_status_data = ohci_hub_status_data, .hub_control = ohci_hub_control, - .hub_irq_enable = ohci_rhsc_enable, .start_port_reset = ohci_start_port_reset, #if defined(CONFIG_PM) .bus_suspend = ohci_bus_suspend, diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c index 8c9c4849db6..7f0f35c7818 100644 --- a/drivers/usb/host/ohci-pxa27x.c +++ b/drivers/usb/host/ohci-pxa27x.c @@ -298,7 +298,6 @@ static const struct hc_driver ohci_pxa27x_hc_driver = { */ .hub_status_data = ohci_hub_status_data, .hub_control = ohci_hub_control, - .hub_irq_enable = ohci_rhsc_enable, #ifdef CONFIG_PM .bus_suspend = ohci_bus_suspend, .bus_resume = ohci_bus_resume, diff --git a/drivers/usb/host/ohci-s3c2410.c b/drivers/usb/host/ohci-s3c2410.c index 9e3dc4069e8..f46af7a718d 100644 --- a/drivers/usb/host/ohci-s3c2410.c +++ b/drivers/usb/host/ohci-s3c2410.c @@ -466,7 +466,6 @@ static const struct hc_driver ohci_s3c2410_hc_driver = { */ .hub_status_data = ohci_s3c2410_hub_status_data, .hub_control = ohci_s3c2410_hub_control, - .hub_irq_enable = ohci_rhsc_enable, #ifdef CONFIG_PM .bus_suspend = ohci_bus_suspend, .bus_resume = ohci_bus_resume, diff --git a/drivers/usb/host/ohci-sa1111.c b/drivers/usb/host/ohci-sa1111.c index 4626b002e67..e4bbe8e188e 100644 --- a/drivers/usb/host/ohci-sa1111.c +++ b/drivers/usb/host/ohci-sa1111.c @@ -231,7 +231,6 @@ static const struct hc_driver ohci_sa1111_hc_driver = { */ .hub_status_data = ohci_hub_status_data, .hub_control = ohci_hub_control, - .hub_irq_enable = ohci_rhsc_enable, #ifdef CONFIG_PM .bus_suspend = ohci_bus_suspend, .bus_resume = ohci_bus_resume, diff --git a/drivers/usb/host/ohci-sh.c b/drivers/usb/host/ohci-sh.c index e7ee607278f..60f03cc7ec4 100644 --- a/drivers/usb/host/ohci-sh.c +++ b/drivers/usb/host/ohci-sh.c @@ -68,7 +68,6 @@ static const struct hc_driver ohci_sh_hc_driver = { */ .hub_status_data = ohci_hub_status_data, .hub_control = ohci_hub_control, - .hub_irq_enable = ohci_rhsc_enable, #ifdef CONFIG_PM .bus_suspend = ohci_bus_suspend, .bus_resume = ohci_bus_resume, diff --git a/drivers/usb/host/ohci-sm501.c b/drivers/usb/host/ohci-sm501.c index 21b164e4abe..cff23637cfc 100644 --- a/drivers/usb/host/ohci-sm501.c +++ b/drivers/usb/host/ohci-sm501.c @@ -75,7 +75,6 @@ static const struct hc_driver ohci_sm501_hc_driver = { */ .hub_status_data = ohci_hub_status_data, .hub_control = ohci_hub_control, - .hub_irq_enable = ohci_rhsc_enable, #ifdef CONFIG_PM .bus_suspend = ohci_bus_suspend, .bus_resume = ohci_bus_resume, diff --git a/drivers/usb/host/ohci-ssb.c b/drivers/usb/host/ohci-ssb.c index 3660c83d80a..23fd6a886bd 100644 --- a/drivers/usb/host/ohci-ssb.c +++ b/drivers/usb/host/ohci-ssb.c @@ -81,7 +81,6 @@ static const struct hc_driver ssb_ohci_hc_driver = { .hub_status_data = ohci_hub_status_data, .hub_control = ohci_hub_control, - .hub_irq_enable = ohci_rhsc_enable, #ifdef CONFIG_PM .bus_suspend = ohci_bus_suspend, .bus_resume = ohci_bus_resume, diff --git a/drivers/usb/host/u132-hcd.c b/drivers/usb/host/u132-hcd.c index 20ad3c48fcb..228f2b070f2 100644 --- a/drivers/usb/host/u132-hcd.c +++ b/drivers/usb/host/u132-hcd.c @@ -2934,16 +2934,6 @@ static int u132_start_port_reset(struct usb_hcd *hcd, unsigned port_num) return 0; } -static void u132_hub_irq_enable(struct usb_hcd *hcd) -{ - struct u132 *u132 = hcd_to_u132(hcd); - if (u132->going > 1) { - dev_err(&u132->platform_dev->dev, "device has been removed %d\n" - , u132->going); - } else if (u132->going > 0) - dev_err(&u132->platform_dev->dev, "device is being removed\n"); -} - #ifdef CONFIG_PM static int u132_bus_suspend(struct usb_hcd *hcd) @@ -2995,7 +2985,6 @@ static struct hc_driver u132_hc_driver = { .bus_suspend = u132_bus_suspend, .bus_resume = u132_bus_resume, .start_port_reset = u132_start_port_reset, - .hub_irq_enable = u132_hub_irq_enable, }; /* -- GitLab From eaea04353e0114a9805fc2cf1ff832cb0ac2570b Mon Sep 17 00:00:00 2001 From: Stefan Lippers-Hollmann Date: Thu, 21 Aug 2008 13:46:11 +0200 Subject: [PATCH 694/750] USB: sisusbvga: add USB ID for 0711:0918 Magic Control Technology Corp. sisusbvga: add USB ID for 0711:0918 Magic Control Technology Corp. usb 1-2: new high speed USB device using ehci_hcd and address 4 usb 1-2: configuration #1 chosen from 1 choice usb 1-2: USB2VGA dongle found at address 4 usb 1-2: Allocated 8 output buffers usb 1-2: 8MB 1 ch/1 r SDR SDRAM, bus width 32 usb 1-2: New USB device found, idVendor=0711, idProduct=0918 usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0 Signed-off-by: Stefan Lippers-Hollmann Signed-off-by: Greg Kroah-Hartman --- drivers/usb/misc/sisusbvga/sisusb.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/usb/misc/sisusbvga/sisusb.c b/drivers/usb/misc/sisusbvga/sisusb.c index fbace41a7cb..69c34a58e20 100644 --- a/drivers/usb/misc/sisusbvga/sisusb.c +++ b/drivers/usb/misc/sisusbvga/sisusb.c @@ -3270,6 +3270,7 @@ static struct usb_device_id sisusb_table [] = { { USB_DEVICE(0x0711, 0x0900) }, { USB_DEVICE(0x0711, 0x0901) }, { USB_DEVICE(0x0711, 0x0902) }, + { USB_DEVICE(0x0711, 0x0918) }, { USB_DEVICE(0x182d, 0x021c) }, { USB_DEVICE(0x182d, 0x0269) }, { } -- GitLab From 0983e56835cbf4796e8f5780c549c32ac1c3afac Mon Sep 17 00:00:00 2001 From: Julien Brunel Date: Thu, 21 Aug 2008 19:46:30 +0200 Subject: [PATCH 695/750] [S390] drivers/s390: Use an IS_ERR test rather than a NULL test In case of error, functions dasd_kmalloc_request and idal_buffer_alloc return an ERR pointer, but never return the NULL pointer. So after a call to one of these functions, a NULL test should be replaced by an IS_ERR test. A simplified version of the semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // @correct_null_test@ expression x,E; statement S1, S2; @@ x = ( dasd_kmalloc_request(...) | idal_buffer_alloc(...) ) <... when != x = E if ( ( - x@p2 != NULL + ! IS_ERR ( x ) | - x@p2 == NULL + IS_ERR( x ) ) ) S1 else S2 ...> ? x = E; // Signed-off-by: Julien Brunel Signed-off-by: Julia Lawall Signed-off-by: Martin Schwidefsky --- drivers/s390/block/dasd_eer.c | 3 ++- drivers/s390/char/tape_char.c | 2 +- drivers/s390/char/tape_std.c | 2 +- 3 files changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/s390/block/dasd_eer.c b/drivers/s390/block/dasd_eer.c index 29da4413ad4..bf512ac75b9 100644 --- a/drivers/s390/block/dasd_eer.c +++ b/drivers/s390/block/dasd_eer.c @@ -16,6 +16,7 @@ #include #include #include +#include #include #include @@ -457,7 +458,7 @@ int dasd_eer_enable(struct dasd_device *device) cqr = dasd_kmalloc_request("ECKD", 1 /* SNSS */, SNSS_DATA_SIZE, device); - if (!cqr) + if (IS_ERR(cqr)) return -ENOMEM; cqr->startdev = device; diff --git a/drivers/s390/char/tape_char.c b/drivers/s390/char/tape_char.c index 687720b552d..be0ce2215c8 100644 --- a/drivers/s390/char/tape_char.c +++ b/drivers/s390/char/tape_char.c @@ -109,7 +109,7 @@ tapechar_check_idalbuffer(struct tape_device *device, size_t block_size) /* The current idal buffer is not correct. Allocate a new one. */ new = idal_buffer_alloc(block_size, 0); - if (new == NULL) + if (IS_ERR(new)) return -ENOMEM; if (device->char_data.idal_buf != NULL) diff --git a/drivers/s390/char/tape_std.c b/drivers/s390/char/tape_std.c index 2a1af4e60be..cc8fd781ee2 100644 --- a/drivers/s390/char/tape_std.c +++ b/drivers/s390/char/tape_std.c @@ -248,7 +248,7 @@ tape_std_mtsetblk(struct tape_device *device, int count) /* Allocate a new idal buffer. */ new = idal_buffer_alloc(count, 0); - if (new == NULL) + if (IS_ERR(new)) return -ENOMEM; if (device->char_data.idal_buf != NULL) idal_buffer_free(device->char_data.idal_buf); -- GitLab From 3e972394f9ee1511e5fdbcf50ac7d79e9cf563bd Mon Sep 17 00:00:00 2001 From: Josef 'Jeff' Sipek Date: Thu, 21 Aug 2008 19:46:31 +0200 Subject: [PATCH 696/750] [S390] Fix uninitialized spinlock use Ever since commit 43ca5c3a1cefdaa09231d64485b8f676118bf1e0 ([S390] Convert monitor calls to function calls.), the kernel refused to IPL with spinlock debugging enabled. BUG: spinlock bad magic on CPU#0, swapper/0 lock: 00000000003a4668, .magic: 00000000, .owner: /-1, .owner_cpu: 0 CPU: 0 Not tainted 2.6.25 #1 Process swapper (pid: 0, task: 000000000034f958, ksp: 0000000000377d60) 0000000000377ab8 0000000000352628 0000000000377d60 0000000000377d60 0000000000016af4 00000000fffff7b5 0000000000377d60 0000000000000000 0000000000000000 0000000000377a18 0000000000000009 0000000000377a18 0000000000377a78 000000000023c920 0000000000016af4 0000000000377a18 0000000000000005 0000000000000000 0000000000377b58 0000000000377ab8 Call Trace: ([<0000000000016a60>] show_trace+0xdc/0x108) [<0000000000016b4e>] show_stack+0xc2/0xfc [<0000000000016c9a>] dump_stack+0xb2/0xc0 [<0000000000172dd4>] Signed-off-by: Josef 'Jeff' Sipek Signed-off-by: Heiko Carstens Signed-off-by: Martin Schwidefsky --- arch/s390/kernel/process.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/arch/s390/kernel/process.c b/arch/s390/kernel/process.c index 9839767d084..3e2c05cb6a8 100644 --- a/arch/s390/kernel/process.c +++ b/arch/s390/kernel/process.c @@ -75,7 +75,9 @@ unsigned long thread_saved_pc(struct task_struct *tsk) return sf->gprs[8]; } -DEFINE_PER_CPU(struct s390_idle_data, s390_idle); +DEFINE_PER_CPU(struct s390_idle_data, s390_idle) = { + .lock = __SPIN_LOCK_UNLOCKED(s390_idle.lock) +}; static int s390_idle_enter(void) { -- GitLab From 8853e505a15f31fe608cb50e038ba2f794eed923 Mon Sep 17 00:00:00 2001 From: Heiko Carstens Date: Thu, 21 Aug 2008 19:46:32 +0200 Subject: [PATCH 697/750] [S390] Remove unneeded spinlock initialization. Remove the now unneeded s390_idle.lock spinlock initialization after Josef Sipek did it the right way in arch/s390/kernel/process.c. Signed-off-by: Heiko Carstens Signed-off-by: Martin Schwidefsky --- arch/s390/kernel/smp.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/arch/s390/kernel/smp.c b/arch/s390/kernel/smp.c index b795b3e24af..00b9b4dec5e 100644 --- a/arch/s390/kernel/smp.c +++ b/arch/s390/kernel/smp.c @@ -610,7 +610,6 @@ static void __init smp_create_idle(unsigned int cpu) if (IS_ERR(p)) panic("failed fork for CPU %u: %li", cpu, PTR_ERR(p)); current_set[cpu] = p; - spin_lock_init(&(&per_cpu(s390_idle, cpu))->lock); } static int __cpuinit smp_alloc_lowcore(int cpu) @@ -845,7 +844,6 @@ void __init smp_prepare_boot_cpu(void) current_set[0] = current; smp_cpu_state[0] = CPU_STATE_CONFIGURED; smp_cpu_polarization[0] = POLARIZATION_UNKNWN; - spin_lock_init(&(&__get_cpu_var(s390_idle))->lock); } void __init smp_cpus_done(unsigned int max_cpus) -- GitLab From 53b41ba7ce4563c33a0449fbcbbd70665477d654 Mon Sep 17 00:00:00 2001 From: Jan Glauber Date: Thu, 21 Aug 2008 19:46:33 +0200 Subject: [PATCH 698/750] [S390] qdio: prevent oopsing if qdio_establish fails If qdio_establish fails we call qdio_shutdown to cleanup the qdio subchannel. The tiq_list entry may not be valid at that time, therefore we must ignore queues with an invalid list entry in tiqdio_remove_input_queues. Signed-off-by: Jan Glauber Signed-off-by: Martin Schwidefsky --- drivers/s390/cio/qdio_thinint.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/drivers/s390/cio/qdio_thinint.c b/drivers/s390/cio/qdio_thinint.c index 9291a771d81..ea7f6140026 100644 --- a/drivers/s390/cio/qdio_thinint.c +++ b/drivers/s390/cio/qdio_thinint.c @@ -113,7 +113,11 @@ void tiqdio_remove_input_queues(struct qdio_irq *irq_ptr) struct qdio_q *q; int i; - for_each_input_queue(irq_ptr, q, i) { + for (i = 0; i < irq_ptr->nr_input_qs; i++) { + q = irq_ptr->input_qs[i]; + /* if establish triggered an error */ + if (!q || !q->entry.prev || !q->entry.next) + continue; list_del_rcu(&q->entry); synchronize_rcu(); } -- GitLab From 58eb27cd7f4f1de2932b3e0e39ea54a27e9fef43 Mon Sep 17 00:00:00 2001 From: Jan Glauber Date: Thu, 21 Aug 2008 19:46:34 +0200 Subject: [PATCH 699/750] [S390] qdio: improve s390 debug feature usage Improve s390 debug feature usage: - log busy bit in dbf - increase size of dbf views - consistent logging of qdio api calls to setup view - print subchannel number so one can associate the interface with the dbf data - only log events to one view Signed-off-by: Jan Glauber Signed-off-by: Martin Schwidefsky --- drivers/s390/cio/qdio_debug.h | 6 +-- drivers/s390/cio/qdio_main.c | 70 +++++++++++++++++------------------ drivers/s390/cio/qdio_setup.c | 6 +-- 3 files changed, 40 insertions(+), 42 deletions(-) diff --git a/drivers/s390/cio/qdio_debug.h b/drivers/s390/cio/qdio_debug.h index 8484b83698e..5a4d85b829a 100644 --- a/drivers/s390/cio/qdio_debug.h +++ b/drivers/s390/cio/qdio_debug.h @@ -61,18 +61,18 @@ /* s390dbf views */ #define QDIO_DBF_SETUP_LEN 8 -#define QDIO_DBF_SETUP_PAGES 4 +#define QDIO_DBF_SETUP_PAGES 8 #define QDIO_DBF_SETUP_NR_AREAS 1 #define QDIO_DBF_TRACE_LEN 8 #define QDIO_DBF_TRACE_NR_AREAS 2 #ifdef CONFIG_QDIO_DEBUG -#define QDIO_DBF_TRACE_PAGES 16 +#define QDIO_DBF_TRACE_PAGES 32 #define QDIO_DBF_SETUP_LEVEL 6 #define QDIO_DBF_TRACE_LEVEL 4 #else /* !CONFIG_QDIO_DEBUG */ -#define QDIO_DBF_TRACE_PAGES 4 +#define QDIO_DBF_TRACE_PAGES 8 #define QDIO_DBF_SETUP_LEVEL 2 #define QDIO_DBF_TRACE_LEVEL 2 #endif /* CONFIG_QDIO_DEBUG */ diff --git a/drivers/s390/cio/qdio_main.c b/drivers/s390/cio/qdio_main.c index d15648514a0..444fc7e521d 100644 --- a/drivers/s390/cio/qdio_main.c +++ b/drivers/s390/cio/qdio_main.c @@ -330,6 +330,7 @@ static int qdio_siga_output(struct qdio_q *q) int cc; u32 busy_bit; u64 start_time = 0; + char dbf_text[15]; QDIO_DBF_TEXT5(0, trace, "sigaout"); QDIO_DBF_HEX5(0, trace, &q, sizeof(void *)); @@ -338,6 +339,9 @@ static int qdio_siga_output(struct qdio_q *q) again: cc = qdio_do_siga_output(q, &busy_bit); if (queue_type(q) == QDIO_IQDIO_QFMT && cc == 2 && busy_bit) { + sprintf(dbf_text, "bb%4x%2x", q->irq_ptr->schid.sch_no, q->nr); + QDIO_DBF_TEXT3(0, trace, dbf_text); + if (!start_time) start_time = get_usecs(); else if ((get_usecs() - start_time) < QDIO_BUSY_BIT_PATIENCE) @@ -748,16 +752,18 @@ static void qdio_kick_outbound_q(struct qdio_q *q) rc = qdio_siga_output(q); switch (rc) { case 0: - /* went smooth this time, reset timestamp */ - q->u.out.timestamp = 0; - /* TODO: improve error handling for CC=0 case */ #ifdef CONFIG_QDIO_DEBUG - QDIO_DBF_TEXT3(0, trace, "cc2reslv"); - sprintf(dbf_text, "%4x%2x%2x", q->irq_ptr->schid.sch_no, q->nr, - atomic_read(&q->u.out.busy_siga_counter)); - QDIO_DBF_TEXT3(0, trace, dbf_text); + if (q->u.out.timestamp) { + QDIO_DBF_TEXT3(0, trace, "cc2reslv"); + sprintf(dbf_text, "%4x%2x%2x", q->irq_ptr->schid.sch_no, + q->nr, + atomic_read(&q->u.out.busy_siga_counter)); + QDIO_DBF_TEXT3(0, trace, dbf_text); + } #endif /* CONFIG_QDIO_DEBUG */ + /* went smooth this time, reset timestamp */ + q->u.out.timestamp = 0; break; /* cc=2 and busy bit */ case (2 | QDIO_ERROR_SIGA_BUSY): @@ -1066,14 +1072,12 @@ void qdio_int_handler(struct ccw_device *cdev, unsigned long intparm, if (IS_ERR(irb)) { switch (PTR_ERR(irb)) { case -EIO: - sprintf(dbf_text, "ierr%4x", - cdev->private->schid.sch_no); + sprintf(dbf_text, "ierr%4x", irq_ptr->schid.sch_no); QDIO_DBF_TEXT2(1, setup, dbf_text); qdio_int_error(cdev); return; case -ETIMEDOUT: - sprintf(dbf_text, "qtoh%4x", - cdev->private->schid.sch_no); + sprintf(dbf_text, "qtoh%4x", irq_ptr->schid.sch_no); QDIO_DBF_TEXT2(1, setup, dbf_text); qdio_int_error(cdev); return; @@ -1124,8 +1128,10 @@ void qdio_int_handler(struct ccw_device *cdev, unsigned long intparm, struct qdio_ssqd_desc *qdio_get_ssqd_desc(struct ccw_device *cdev) { struct qdio_irq *irq_ptr; + char dbf_text[15]; - QDIO_DBF_TEXT0(0, setup, "getssqd"); + sprintf(dbf_text, "qssq%4x", cdev->private->schid.sch_no); + QDIO_DBF_TEXT0(0, setup, dbf_text); irq_ptr = cdev->private->qdio_data; if (!irq_ptr) @@ -1149,14 +1155,13 @@ int qdio_cleanup(struct ccw_device *cdev, int how) char dbf_text[15]; int rc; + sprintf(dbf_text, "qcln%4x", cdev->private->schid.sch_no); + QDIO_DBF_TEXT0(0, setup, dbf_text); + irq_ptr = cdev->private->qdio_data; if (!irq_ptr) return -ENODEV; - sprintf(dbf_text, "qcln%4x", irq_ptr->schid.sch_no); - QDIO_DBF_TEXT1(0, trace, dbf_text); - QDIO_DBF_TEXT0(0, setup, dbf_text); - rc = qdio_shutdown(cdev, how); if (rc == 0) rc = qdio_free(cdev); @@ -1191,6 +1196,9 @@ int qdio_shutdown(struct ccw_device *cdev, int how) unsigned long flags; char dbf_text[15]; + sprintf(dbf_text, "qshu%4x", cdev->private->schid.sch_no); + QDIO_DBF_TEXT0(0, setup, dbf_text); + irq_ptr = cdev->private->qdio_data; if (!irq_ptr) return -ENODEV; @@ -1205,10 +1213,6 @@ int qdio_shutdown(struct ccw_device *cdev, int how) return 0; } - sprintf(dbf_text, "qsqs%4x", irq_ptr->schid.sch_no); - QDIO_DBF_TEXT1(0, trace, dbf_text); - QDIO_DBF_TEXT0(0, setup, dbf_text); - tiqdio_remove_input_queues(irq_ptr); qdio_shutdown_queues(cdev); qdio_shutdown_debug_entries(irq_ptr, cdev); @@ -1263,16 +1267,14 @@ int qdio_free(struct ccw_device *cdev) struct qdio_irq *irq_ptr; char dbf_text[15]; + sprintf(dbf_text, "qfre%4x", cdev->private->schid.sch_no); + QDIO_DBF_TEXT0(0, setup, dbf_text); + irq_ptr = cdev->private->qdio_data; if (!irq_ptr) return -ENODEV; mutex_lock(&irq_ptr->setup_mutex); - - sprintf(dbf_text, "qfqs%4x", irq_ptr->schid.sch_no); - QDIO_DBF_TEXT1(0, trace, dbf_text); - QDIO_DBF_TEXT0(0, setup, dbf_text); - cdev->private->qdio_data = NULL; mutex_unlock(&irq_ptr->setup_mutex); @@ -1295,7 +1297,6 @@ int qdio_initialize(struct qdio_initialize *init_data) sprintf(dbf_text, "qini%4x", init_data->cdev->private->schid.sch_no); QDIO_DBF_TEXT0(0, setup, dbf_text); - QDIO_DBF_TEXT0(0, trace, dbf_text); rc = qdio_allocate(init_data); if (rc) @@ -1319,7 +1320,6 @@ int qdio_allocate(struct qdio_initialize *init_data) sprintf(dbf_text, "qalc%4x", init_data->cdev->private->schid.sch_no); QDIO_DBF_TEXT0(0, setup, dbf_text); - QDIO_DBF_TEXT0(0, trace, dbf_text); if ((init_data->no_input_qs && !init_data->input_handler) || (init_data->no_output_qs && !init_data->output_handler)) @@ -1389,6 +1389,9 @@ int qdio_establish(struct qdio_initialize *init_data) unsigned long saveflags; int rc; + sprintf(dbf_text, "qest%4x", cdev->private->schid.sch_no); + QDIO_DBF_TEXT0(0, setup, dbf_text); + irq_ptr = cdev->private->qdio_data; if (!irq_ptr) return -ENODEV; @@ -1399,10 +1402,6 @@ int qdio_establish(struct qdio_initialize *init_data) if (!try_module_get(THIS_MODULE)) return -EINVAL; - sprintf(dbf_text, "qest%4x", cdev->private->schid.sch_no); - QDIO_DBF_TEXT0(0, setup, dbf_text); - QDIO_DBF_TEXT0(0, trace, dbf_text); - mutex_lock(&irq_ptr->setup_mutex); qdio_setup_irq(init_data); @@ -1472,6 +1471,9 @@ int qdio_activate(struct ccw_device *cdev) unsigned long saveflags; char dbf_text[20]; + sprintf(dbf_text, "qact%4x", cdev->private->schid.sch_no); + QDIO_DBF_TEXT0(0, setup, dbf_text); + irq_ptr = cdev->private->qdio_data; if (!irq_ptr) return -ENODEV; @@ -1485,10 +1487,6 @@ int qdio_activate(struct ccw_device *cdev) goto out; } - sprintf(dbf_text, "qact%4x", irq_ptr->schid.sch_no); - QDIO_DBF_TEXT2(0, setup, dbf_text); - QDIO_DBF_TEXT2(0, trace, dbf_text); - irq_ptr->ccw.cmd_code = irq_ptr->aqueue.cmd; irq_ptr->ccw.flags = CCW_FLAG_SLI; irq_ptr->ccw.count = irq_ptr->aqueue.count; @@ -1663,7 +1661,7 @@ int do_QDIO(struct ccw_device *cdev, unsigned int callflags, #ifdef CONFIG_QDIO_DEBUG char dbf_text[20]; - sprintf(dbf_text, "doQD%04x", cdev->private->schid.sch_no); + sprintf(dbf_text, "doQD%4x", cdev->private->schid.sch_no); QDIO_DBF_TEXT3(0, trace, dbf_text); #endif /* CONFIG_QDIO_DEBUG */ diff --git a/drivers/s390/cio/qdio_setup.c b/drivers/s390/cio/qdio_setup.c index 1bd2a208db2..1679e2f91c9 100644 --- a/drivers/s390/cio/qdio_setup.c +++ b/drivers/s390/cio/qdio_setup.c @@ -165,7 +165,7 @@ static void setup_queues(struct qdio_irq *irq_ptr, void **output_sbal_array = qdio_init->output_sbal_addr_array; int i; - sprintf(dbf_text, "qfqs%4x", qdio_init->cdev->private->schid.sch_no); + sprintf(dbf_text, "qset%4x", qdio_init->cdev->private->schid.sch_no); QDIO_DBF_TEXT0(0, setup, dbf_text); for_each_input_queue(irq_ptr, q, i) { @@ -285,7 +285,7 @@ void qdio_setup_ssqd_info(struct qdio_irq *irq_ptr) rc = __get_ssqd_info(irq_ptr); if (rc) { QDIO_DBF_TEXT2(0, setup, "ssqdasig"); - sprintf(dbf_text, "schno%x", irq_ptr->schid.sch_no); + sprintf(dbf_text, "schn%4x", irq_ptr->schid.sch_no); QDIO_DBF_TEXT2(0, setup, dbf_text); sprintf(dbf_text, "rc:%d", rc); QDIO_DBF_TEXT2(0, setup, dbf_text); @@ -447,7 +447,7 @@ void qdio_print_subchannel_info(struct qdio_irq *irq_ptr, { char s[80]; - sprintf(s, "%s ", cdev->dev.bus_id); + sprintf(s, "%s sc:%x ", cdev->dev.bus_id, irq_ptr->schid.sch_no); switch (irq_ptr->qib.qfmt) { case QDIO_QETH_QFMT: -- GitLab From 0686e402c365c92396d4c7abfaa24810f9cb77cc Mon Sep 17 00:00:00 2001 From: Jan Glauber Date: Thu, 21 Aug 2008 19:46:35 +0200 Subject: [PATCH 700/750] [S390] qdio: remove the module_get & module_put pair Increasing the qdio reference count for every used subchannel is unnecessary since unloading qdio (if build as a module) is only possible if other modules that use qdio are unloaded. Unloading modules that use qdio in turn requires that these modules shut down all qdio subchannels. Therefore the additional module_get reference is not needed. Signed-off-by: Jan Glauber Signed-off-by: Martin Schwidefsky --- drivers/s390/cio/qdio_main.c | 4 ---- 1 file changed, 4 deletions(-) diff --git a/drivers/s390/cio/qdio_main.c b/drivers/s390/cio/qdio_main.c index 444fc7e521d..e6eabc85342 100644 --- a/drivers/s390/cio/qdio_main.c +++ b/drivers/s390/cio/qdio_main.c @@ -1251,7 +1251,6 @@ no_cleanup: qdio_set_state(irq_ptr, QDIO_IRQ_STATE_INACTIVE); mutex_unlock(&irq_ptr->setup_mutex); - module_put(THIS_MODULE); if (rc) return rc; return 0; @@ -1399,9 +1398,6 @@ int qdio_establish(struct qdio_initialize *init_data) if (cdev->private->state != DEV_STATE_ONLINE) return -EINVAL; - if (!try_module_get(THIS_MODULE)) - return -EINVAL; - mutex_lock(&irq_ptr->setup_mutex); qdio_setup_irq(init_data); -- GitLab From 16f7f9564c3ae190954f2ec55f385a268b93ac4d Mon Sep 17 00:00:00 2001 From: Peter Oberparleiter Date: Thu, 21 Aug 2008 19:46:36 +0200 Subject: [PATCH 701/750] [S390] cio: fix ccw group device cleanup Fix ccw group device initialization: initialize device object before using reference counting during cleanup. Fixes the following message when group device initialization fails (e.g. because too few devices where specified): kobject: '' (..): is not initialized, yet kobject_put() is being called. Signed-off-by: Peter Oberparleiter Signed-off-by: Martin Schwidefsky --- drivers/s390/cio/ccwgroup.c | 20 ++++++++++++-------- 1 file changed, 12 insertions(+), 8 deletions(-) diff --git a/drivers/s390/cio/ccwgroup.c b/drivers/s390/cio/ccwgroup.c index 26a930e832b..e0ce65fca4e 100644 --- a/drivers/s390/cio/ccwgroup.c +++ b/drivers/s390/cio/ccwgroup.c @@ -112,8 +112,10 @@ ccwgroup_release (struct device *dev) gdev = to_ccwgroupdev(dev); for (i = 0; i < gdev->count; i++) { - dev_set_drvdata(&gdev->cdev[i]->dev, NULL); - put_device(&gdev->cdev[i]->dev); + if (gdev->cdev[i]) { + dev_set_drvdata(&gdev->cdev[i]->dev, NULL); + put_device(&gdev->cdev[i]->dev); + } } kfree(gdev); } @@ -221,6 +223,13 @@ int ccwgroup_create_from_string(struct device *root, unsigned int creator_id, atomic_set(&gdev->onoff, 0); mutex_init(&gdev->reg_mutex); mutex_lock(&gdev->reg_mutex); + gdev->creator_id = creator_id; + gdev->count = num_devices; + gdev->dev.bus = &ccwgroup_bus_type; + gdev->dev.parent = root; + gdev->dev.release = ccwgroup_release; + device_initialize(&gdev->dev); + curr_buf = buf; for (i = 0; i < num_devices && curr_buf; i++) { rc = __get_next_bus_id(&curr_buf, tmp_bus_id); @@ -258,16 +267,11 @@ int ccwgroup_create_from_string(struct device *root, unsigned int creator_id, rc = -EINVAL; goto error; } - gdev->creator_id = creator_id; - gdev->count = num_devices; - gdev->dev.bus = &ccwgroup_bus_type; - gdev->dev.parent = root; - gdev->dev.release = ccwgroup_release; snprintf (gdev->dev.bus_id, BUS_ID_SIZE, "%s", gdev->cdev[0]->dev.bus_id); - rc = device_register(&gdev->dev); + rc = device_add(&gdev->dev); if (rc) goto error; get_device(&gdev->dev); -- GitLab From 152382af4056aadc0c2ea2e8e8258b277be085bf Mon Sep 17 00:00:00 2001 From: Eric Sandeen Date: Thu, 21 Aug 2008 19:46:37 +0200 Subject: [PATCH 702/750] [S390] fix ext2_find_next_bit ext4 does not work on s390 because ext2_find_next_bit is broken. Fortunately this function is only used by ext4. The function uses ffs which does not work analog to ffz. The result of ffs has an offset of 1 which is not taken into account. To fix this use the low level __ffs_word function directly instead of the ill defined ffs. In addition the patch improves find_next_zero_bit and ext2_find_next_zero_bit by passing the bit offset into __ffz_word instead of adding it after the function call returned. Signed-off-by: Eric Sandeen Signed-off-by: Martin Schwidefsky --- arch/s390/include/asm/bitops.h | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/s390/include/asm/bitops.h b/arch/s390/include/asm/bitops.h index b4eb24ab5af..8e9243ae0c1 100644 --- a/arch/s390/include/asm/bitops.h +++ b/arch/s390/include/asm/bitops.h @@ -709,7 +709,7 @@ static inline int find_next_zero_bit (const unsigned long * addr, * __ffz_word returns __BITOPS_WORDSIZE * if no zero bit is present in the word. */ - set = __ffz_word(0, *p >> bit) + bit; + set = __ffz_word(bit, *p >> bit); if (set >= size) return size + offset; if (set < __BITOPS_WORDSIZE) @@ -824,7 +824,7 @@ static inline int ext2_find_next_zero_bit(void *vaddr, unsigned long size, * s390 version of ffz returns __BITOPS_WORDSIZE * if no zero bit is present in the word. */ - set = ffz(__load_ulong_le(p, 0) >> bit) + bit; + set = __ffz_word(bit, __load_ulong_le(p, 0) >> bit); if (set >= size) return size + offset; if (set < __BITOPS_WORDSIZE) @@ -865,7 +865,7 @@ static inline int ext2_find_next_bit(void *vaddr, unsigned long size, * s390 version of ffz returns __BITOPS_WORDSIZE * if no zero bit is present in the word. */ - set = ffs(__load_ulong_le(p, 0) >> bit) + bit; + set = __ffs_word(0, __load_ulong_le(p, 0) & (~0UL << bit)); if (set >= size) return size + offset; if (set < __BITOPS_WORDSIZE) -- GitLab From 49fd38bdaa96f093fcad3176a781a4d0de8f8602 Mon Sep 17 00:00:00 2001 From: Stefan Weinhuber Date: Thu, 21 Aug 2008 19:46:38 +0200 Subject: [PATCH 703/750] [S390] dasd: fix data size for PSF/PRSSD command The Perform Subsystem Function/Prepare for Read Subsystem Data command requires 12 bytes of parameter data, but the respective data structure dasd_psf_prssd_data has a length of 16 bytes. Current storage servers ignore the obsolete bytes, but older models fail to execute the command and report an incorrect length error. This causes the device initilization for these devices to fail. To fix this problem we need to correct the dasd_psf_prssd_data structure and shorten it to the correct length. Reported-by: Ivan Warren Reviewed-by: Ivan Warren Tested-by: Ivan Warren CC: stable Signed-off-by: Stefan Weinhuber --- drivers/s390/block/dasd_eckd.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/s390/block/dasd_eckd.h b/drivers/s390/block/dasd_eckd.h index 4bf0aa5112c..2476f87d21d 100644 --- a/drivers/s390/block/dasd_eckd.h +++ b/drivers/s390/block/dasd_eckd.h @@ -308,7 +308,7 @@ struct dasd_psf_prssd_data { unsigned char flags; unsigned char reserved[4]; unsigned char suborder; - unsigned char varies[9]; + unsigned char varies[5]; } __attribute__ ((packed)); /* -- GitLab From 91c36919a456589f4f073671474a1f899e0d3c2b Mon Sep 17 00:00:00 2001 From: Peter Oberparleiter Date: Thu, 21 Aug 2008 19:46:39 +0200 Subject: [PATCH 704/750] [S390] cio: call ccw driver notify function with lock held Calling a ccw driver's notify function without the ccw device lock held opens up a race window between discovery and handling of a change in the device operational state. As a result, the device driver may encounter unexpected device malfunction, leading to out-of-retry situations or similar. Remove race by extending the ccw device lock from state change discovery to the calling of the notify function. Signed-off-by: Peter Oberparleiter Signed-off-by: Martin Schwidefsky --- drivers/s390/block/dasd.c | 5 +---- drivers/s390/cio/css.c | 1 - drivers/s390/cio/device.c | 40 +++++++++++++++++------------------ drivers/s390/cio/device.h | 2 +- drivers/s390/cio/device_fsm.c | 31 ++++++++++++++++----------- 5 files changed, 41 insertions(+), 38 deletions(-) diff --git a/drivers/s390/block/dasd.c b/drivers/s390/block/dasd.c index 1b6c52ef733..acb78017e7d 100644 --- a/drivers/s390/block/dasd.c +++ b/drivers/s390/block/dasd.c @@ -2333,13 +2333,11 @@ int dasd_generic_notify(struct ccw_device *cdev, int event) { struct dasd_device *device; struct dasd_ccw_req *cqr; - unsigned long flags; int ret; - device = dasd_device_from_cdev(cdev); + device = dasd_device_from_cdev_locked(cdev); if (IS_ERR(device)) return 0; - spin_lock_irqsave(get_ccwdev_lock(cdev), flags); ret = 0; switch (event) { case CIO_GONE: @@ -2369,7 +2367,6 @@ int dasd_generic_notify(struct ccw_device *cdev, int event) ret = 1; break; } - spin_unlock_irqrestore(get_ccwdev_lock(cdev), flags); dasd_put_device(device); return ret; } diff --git a/drivers/s390/cio/css.c b/drivers/s390/cio/css.c index 46c021d880d..51489eff6b0 100644 --- a/drivers/s390/cio/css.c +++ b/drivers/s390/cio/css.c @@ -477,7 +477,6 @@ void css_schedule_eval_all(void) void css_wait_for_slow_path(void) { - flush_workqueue(ccw_device_notify_work); flush_workqueue(slow_path_wq); } diff --git a/drivers/s390/cio/device.c b/drivers/s390/cio/device.c index e818d0c54c0..28221030b88 100644 --- a/drivers/s390/cio/device.c +++ b/drivers/s390/cio/device.c @@ -150,7 +150,6 @@ static struct css_driver io_subchannel_driver = { }; struct workqueue_struct *ccw_device_work; -struct workqueue_struct *ccw_device_notify_work; wait_queue_head_t ccw_device_init_wq; atomic_t ccw_device_init_count; @@ -168,11 +167,6 @@ init_ccw_bus_type (void) ccw_device_work = create_singlethread_workqueue("cio"); if (!ccw_device_work) return -ENOMEM; /* FIXME: better errno ? */ - ccw_device_notify_work = create_singlethread_workqueue("cio_notify"); - if (!ccw_device_notify_work) { - ret = -ENOMEM; /* FIXME: better errno ? */ - goto out_err; - } slow_path_wq = create_singlethread_workqueue("kslowcrw"); if (!slow_path_wq) { ret = -ENOMEM; /* FIXME: better errno ? */ @@ -192,8 +186,6 @@ init_ccw_bus_type (void) out_err: if (ccw_device_work) destroy_workqueue(ccw_device_work); - if (ccw_device_notify_work) - destroy_workqueue(ccw_device_notify_work); if (slow_path_wq) destroy_workqueue(slow_path_wq); return ret; @@ -204,7 +196,6 @@ cleanup_ccw_bus_type (void) { css_driver_unregister(&io_subchannel_driver); bus_unregister(&ccw_bus_type); - destroy_workqueue(ccw_device_notify_work); destroy_workqueue(ccw_device_work); } @@ -1496,11 +1487,22 @@ static void device_set_disconnected(struct ccw_device *cdev) ccw_device_schedule_recovery(); } +void ccw_device_set_notoper(struct ccw_device *cdev) +{ + struct subchannel *sch = to_subchannel(cdev->dev.parent); + + CIO_TRACE_EVENT(2, "notoper"); + CIO_TRACE_EVENT(2, sch->dev.bus_id); + ccw_device_set_timeout(cdev, 0); + cio_disable_subchannel(sch); + cdev->private->state = DEV_STATE_NOT_OPER; +} + static int io_subchannel_sch_event(struct subchannel *sch, int slow) { int event, ret, disc; unsigned long flags; - enum { NONE, UNREGISTER, UNREGISTER_PROBE, REPROBE } action; + enum { NONE, UNREGISTER, UNREGISTER_PROBE, REPROBE, DISC } action; struct ccw_device *cdev; spin_lock_irqsave(sch->lock, flags); @@ -1535,16 +1537,11 @@ static int io_subchannel_sch_event(struct subchannel *sch, int slow) } /* fall through */ case CIO_GONE: - /* Prevent unwanted effects when opening lock. */ - cio_disable_subchannel(sch); - device_set_disconnected(cdev); /* Ask driver what to do with device. */ - action = UNREGISTER; - spin_unlock_irqrestore(sch->lock, flags); - ret = io_subchannel_notify(sch, event); - spin_lock_irqsave(sch->lock, flags); - if (ret) - action = NONE; + if (io_subchannel_notify(sch, event)) + action = DISC; + else + action = UNREGISTER; break; case CIO_REVALIDATE: /* Device will be removed, so no notify necessary. */ @@ -1565,6 +1562,7 @@ static int io_subchannel_sch_event(struct subchannel *sch, int slow) switch (action) { case UNREGISTER: case UNREGISTER_PROBE: + ccw_device_set_notoper(cdev); /* Unregister device (will use subchannel lock). */ spin_unlock_irqrestore(sch->lock, flags); css_sch_device_unregister(sch); @@ -1577,6 +1575,9 @@ static int io_subchannel_sch_event(struct subchannel *sch, int slow) case REPROBE: ccw_device_trigger_reprobe(cdev); break; + case DISC: + device_set_disconnected(cdev); + break; default: break; } @@ -1828,5 +1829,4 @@ EXPORT_SYMBOL(ccw_driver_unregister); EXPORT_SYMBOL(get_ccwdev_by_busid); EXPORT_SYMBOL(ccw_bus_type); EXPORT_SYMBOL(ccw_device_work); -EXPORT_SYMBOL(ccw_device_notify_work); EXPORT_SYMBOL_GPL(ccw_device_get_subchannel_id); diff --git a/drivers/s390/cio/device.h b/drivers/s390/cio/device.h index 9800a8335a3..6f5c3f2b358 100644 --- a/drivers/s390/cio/device.h +++ b/drivers/s390/cio/device.h @@ -72,7 +72,6 @@ dev_fsm_final_state(struct ccw_device *cdev) } extern struct workqueue_struct *ccw_device_work; -extern struct workqueue_struct *ccw_device_notify_work; extern wait_queue_head_t ccw_device_init_wq; extern atomic_t ccw_device_init_count; @@ -120,6 +119,7 @@ int ccw_device_stlck(struct ccw_device *); void ccw_device_trigger_reprobe(struct ccw_device *); void ccw_device_kill_io(struct ccw_device *); int ccw_device_notify(struct ccw_device *, int); +void ccw_device_set_notoper(struct ccw_device *cdev); /* qdio needs this. */ void ccw_device_set_timeout(struct ccw_device *, int); diff --git a/drivers/s390/cio/device_fsm.c b/drivers/s390/cio/device_fsm.c index 8b5fe57fb2f..550508df952 100644 --- a/drivers/s390/cio/device_fsm.c +++ b/drivers/s390/cio/device_fsm.c @@ -337,26 +337,34 @@ int ccw_device_notify(struct ccw_device *cdev, int event) return 0; if (!cdev->online) return 0; + CIO_MSG_EVENT(2, "notify called for 0.%x.%04x, event=%d\n", + cdev->private->dev_id.ssid, cdev->private->dev_id.devno, + event); return cdev->drv->notify ? cdev->drv->notify(cdev, event) : 0; } -static void -ccw_device_oper_notify(struct work_struct *work) +static void cmf_reenable_delayed(struct work_struct *work) { struct ccw_device_private *priv; struct ccw_device *cdev; - int ret; priv = container_of(work, struct ccw_device_private, kick_work); cdev = priv->cdev; - ret = ccw_device_notify(cdev, CIO_OPER); - if (ret) { + cmf_reenable(cdev); +} + +static void ccw_device_oper_notify(struct ccw_device *cdev) +{ + if (ccw_device_notify(cdev, CIO_OPER)) { /* Reenable channel measurements, if needed. */ - cmf_reenable(cdev); - wake_up(&cdev->private->wait_q); - } else - /* Driver doesn't want device back. */ - ccw_device_do_unreg_rereg(work); + PREPARE_WORK(&cdev->private->kick_work, cmf_reenable_delayed); + queue_work(ccw_device_work, &cdev->private->kick_work); + return; + } + /* Driver doesn't want device back. */ + ccw_device_set_notoper(cdev); + PREPARE_WORK(&cdev->private->kick_work, ccw_device_do_unreg_rereg); + queue_work(ccw_device_work, &cdev->private->kick_work); } /* @@ -386,8 +394,7 @@ ccw_device_done(struct ccw_device *cdev, int state) if (cdev->private->flags.donotify) { cdev->private->flags.donotify = 0; - PREPARE_WORK(&cdev->private->kick_work, ccw_device_oper_notify); - queue_work(ccw_device_notify_work, &cdev->private->kick_work); + ccw_device_oper_notify(cdev); } wake_up(&cdev->private->wait_q); -- GitLab From 04f64b5756872b474d9429e3b6987ada10bb8012 Mon Sep 17 00:00:00 2001 From: Gerald Schaefer Date: Thu, 21 Aug 2008 19:46:40 +0200 Subject: [PATCH 705/750] [S390] dcssblk: fix race in dcssblk_add_store() Concurrently adding the same segment may lead to duplicate device_register() calls, which will trigger an error in kobject code: "... don't try to register things with the same name in the same directory". This patch adds a check to avoid this. Signed-off-by: Gerald Schaefer Signed-off-by: Martin Schwidefsky --- drivers/s390/block/dcssblk.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/s390/block/dcssblk.c b/drivers/s390/block/dcssblk.c index 01fcdd91b84..db85f1fb131 100644 --- a/drivers/s390/block/dcssblk.c +++ b/drivers/s390/block/dcssblk.c @@ -384,6 +384,10 @@ dcssblk_add_store(struct device *dev, struct device_attribute *attr, const char * get minor, add to list */ down_write(&dcssblk_devices_sem); + if (dcssblk_get_segment_by_name(local_buf)) { + rc = -EEXIST; + goto release_gd; + } rc = dcssblk_assign_free_minor(dev_info); if (rc) { up_write(&dcssblk_devices_sem); -- GitLab From cce7496d3d5910a003109207f9737c3be658aa1a Mon Sep 17 00:00:00 2001 From: Martin Schwidefsky Date: Thu, 21 Aug 2008 19:46:41 +0200 Subject: [PATCH 706/750] [S390] Update default configuration. Signed-off-by: Martin Schwidefsky --- arch/s390/defconfig | 54 +++++++++++++++++++++++++++++++-------------- 1 file changed, 38 insertions(+), 16 deletions(-) diff --git a/arch/s390/defconfig b/arch/s390/defconfig index c5cdb975d59..9b0bc2c9fba 100644 --- a/arch/s390/defconfig +++ b/arch/s390/defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.26-rc4 -# Fri May 30 09:49:33 2008 +# Linux kernel version: 2.6.27-rc4 +# Thu Aug 21 19:43:29 2008 # CONFIG_SCHED_MC=y CONFIG_MMU=y @@ -68,7 +68,6 @@ CONFIG_INITRAMFS_SOURCE="" CONFIG_SYSCTL=y # CONFIG_EMBEDDED is not set CONFIG_SYSCTL_SYSCALL=y -CONFIG_SYSCTL_SYSCALL_CHECK=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set @@ -93,11 +92,17 @@ CONFIG_SLAB=y # CONFIG_MARKERS is not set CONFIG_HAVE_OPROFILE=y CONFIG_KPROBES=y +# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set CONFIG_KRETPROBES=y +# CONFIG_HAVE_IOREMAP_PROT is not set CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y +# CONFIG_HAVE_ARCH_TRACEHOOK is not set # CONFIG_HAVE_DMA_ATTRS is not set +# CONFIG_USE_GENERIC_SMP_HELPERS is not set +# CONFIG_HAVE_CLK is not set CONFIG_PROC_PAGE_MONITOR=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set @@ -113,6 +118,7 @@ CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y # CONFIG_BLK_DEV_IO_TRACE is not set CONFIG_BLK_DEV_BSG=y +# CONFIG_BLK_DEV_INTEGRITY is not set CONFIG_BLOCK_COMPAT=y # @@ -175,6 +181,8 @@ CONFIG_PREEMPT=y CONFIG_ARCH_SPARSEMEM_ENABLE=y CONFIG_ARCH_SPARSEMEM_DEFAULT=y CONFIG_ARCH_SELECT_MEMORY_MODEL=y +CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y CONFIG_SELECT_MEMORY_MODEL=y # CONFIG_FLATMEM_MANUAL is not set # CONFIG_DISCONTIGMEM_MANUAL is not set @@ -185,8 +193,12 @@ CONFIG_HAVE_MEMORY_PRESENT=y CONFIG_SPARSEMEM_EXTREME=y CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y CONFIG_SPARSEMEM_VMEMMAP=y +CONFIG_MEMORY_HOTPLUG=y +CONFIG_MEMORY_HOTPLUG_SPARSE=y +CONFIG_MEMORY_HOTREMOVE=y CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 +CONFIG_MIGRATION=y CONFIG_RESOURCES_64BIT=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y @@ -198,6 +210,7 @@ CONFIG_VIRT_TO_BUS=y CONFIG_MACHCHK_WARNING=y CONFIG_QDIO=y # CONFIG_QDIO_DEBUG is not set +CONFIG_CHSC_SCH=m # # Misc @@ -206,6 +219,7 @@ CONFIG_IPL=y # CONFIG_IPL_TAPE is not set CONFIG_IPL_VM=y CONFIG_BINFMT_ELF=y +CONFIG_COMPAT_BINFMT_ELF=y CONFIG_BINFMT_MISC=m CONFIG_FORCE_MAX_ZONEORDER=9 # CONFIG_PROCESS_DEBUG is not set @@ -226,10 +240,6 @@ CONFIG_S390_HYPFS_FS=y CONFIG_KEXEC=y # CONFIG_ZFCPDUMP is not set CONFIG_S390_GUEST=y - -# -# Networking -# CONFIG_NET=y # @@ -364,7 +374,6 @@ CONFIG_NET_SCH_CBQ=m # CONFIG_NET_SCH_HTB is not set # CONFIG_NET_SCH_HFSC is not set CONFIG_NET_SCH_PRIO=m -CONFIG_NET_SCH_RR=m CONFIG_NET_SCH_RED=m CONFIG_NET_SCH_SFQ=m CONFIG_NET_SCH_TEQL=m @@ -430,7 +439,9 @@ CONFIG_CCW=y CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y -# CONFIG_FW_LOADER is not set +CONFIG_FW_LOADER=y +# CONFIG_FIRMWARE_IN_KERNEL is not set +CONFIG_EXTRA_FIRMWARE="" # CONFIG_DEBUG_DRIVER is not set # CONFIG_DEBUG_DEVRES is not set CONFIG_SYS_HYPERVISOR=y @@ -507,6 +518,11 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_DEBUG is not set CONFIG_ZFCP=y +CONFIG_SCSI_DH=m +CONFIG_SCSI_DH_RDAC=m +CONFIG_SCSI_DH_HP_SW=m +CONFIG_SCSI_DH_EMC=m +CONFIG_SCSI_DH_ALUA=m CONFIG_MD=y CONFIG_BLK_DEV_MD=y CONFIG_MD_LINEAR=m @@ -522,14 +538,10 @@ CONFIG_DM_CRYPT=y CONFIG_DM_SNAPSHOT=y CONFIG_DM_MIRROR=y CONFIG_DM_ZERO=y -CONFIG_DM_MULTIPATH=y -# CONFIG_DM_MULTIPATH_EMC is not set -# CONFIG_DM_MULTIPATH_RDAC is not set -# CONFIG_DM_MULTIPATH_HP is not set +CONFIG_DM_MULTIPATH=m # CONFIG_DM_DELAY is not set # CONFIG_DM_UEVENT is not set CONFIG_NETDEVICES=y -# CONFIG_NETDEVICES_MULTIQUEUE is not set # CONFIG_IFB is not set CONFIG_DUMMY=m CONFIG_BONDING=m @@ -544,7 +556,6 @@ CONFIG_NET_ETHERNET=y # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set CONFIG_NETDEV_1000=y -# CONFIG_E1000E_ENABLED is not set CONFIG_NETDEV_10000=y # CONFIG_TR is not set # CONFIG_WAN is not set @@ -576,7 +587,10 @@ CONFIG_DEVKMEM=y CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 +CONFIG_HVC_DRIVER=y +CONFIG_VIRTIO_CONSOLE=y CONFIG_HW_RANDOM=m +CONFIG_HW_RANDOM_VIRTIO=m # CONFIG_R3964 is not set CONFIG_RAW_DRIVER=m CONFIG_MAX_RAW_DEVS=256 @@ -616,6 +630,7 @@ CONFIG_MONWRITER=m CONFIG_S390_VMUR=m # CONFIG_POWER_SUPPLY is not set # CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set # @@ -693,6 +708,7 @@ CONFIG_CONFIGFS_FS=m # CONFIG_CRAMFS is not set # CONFIG_VXFS_FS is not set # CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_ROMFS_FS is not set @@ -712,7 +728,6 @@ CONFIG_LOCKD_V4=y CONFIG_EXPORTFS=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y -# CONFIG_SUNRPC_BIND34 is not set # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set @@ -780,6 +795,7 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_WRITECOUNT is not set +CONFIG_DEBUG_MEMORY_INIT=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_FRAME_POINTER is not set @@ -789,6 +805,7 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_LKDTM is not set # CONFIG_FAULT_INJECTION is not set # CONFIG_LATENCYTOP is not set +CONFIG_SYSCTL_SYSCALL_CHECK=y CONFIG_SAMPLES=y # CONFIG_SAMPLE_KOBJECT is not set # CONFIG_SAMPLE_KPROBES is not set @@ -847,6 +864,10 @@ CONFIG_CRYPTO_HMAC=m # CONFIG_CRYPTO_MD4 is not set CONFIG_CRYPTO_MD5=m # CONFIG_CRYPTO_MICHAEL_MIC is not set +CONFIG_CRYPTO_RMD128=m +CONFIG_CRYPTO_RMD160=m +CONFIG_CRYPTO_RMD256=m +CONFIG_CRYPTO_RMD320=m CONFIG_CRYPTO_SHA1=m # CONFIG_CRYPTO_SHA256 is not set # CONFIG_CRYPTO_SHA512 is not set @@ -895,6 +916,7 @@ CONFIG_BITREVERSE=m # CONFIG_GENERIC_FIND_NEXT_BIT is not set # CONFIG_CRC_CCITT is not set # CONFIG_CRC16 is not set +CONFIG_CRC_T10DIF=y # CONFIG_CRC_ITU_T is not set CONFIG_CRC32=m CONFIG_CRC7=m -- GitLab From 38cc1c3df77c1bb739a4766788eb9fa49f16ffdf Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Thu, 21 Aug 2008 20:24:24 -0700 Subject: [PATCH 707/750] x86: work around MTRR mask setting Joshua Hoblitt reported that only 3 GB of his 16 GB of RAM is usable. Booting with mtrr_show showed us the BIOS-initialized MTRR settings - which are all wrong. So the root cause is that the BIOS has not set the mask correctly: > [ 0.429971] MSR00000200: 00000000d0000000 > [ 0.433305] MSR00000201: 0000000ff0000800 > should be ==> [ 0.433305] MSR00000201: 0000003ff0000800 > > [ 0.436638] MSR00000202: 00000000e0000000 > [ 0.439971] MSR00000203: 0000000fe0000800 > should be ==> [ 0.439971] MSR00000203: 0000003fe0000800 > > [ 0.443304] MSR00000204: 0000000000000006 > [ 0.446637] MSR00000205: 0000000c00000800 > should be ==> [ 0.446637] MSR00000205: 0000003c00000800 > > [ 0.449970] MSR00000206: 0000000400000006 > [ 0.453303] MSR00000207: 0000000fe0000800 > should be ==> [ 0.453303] MSR00000207: 0000003fe0000800 > > [ 0.456636] MSR00000208: 0000000420000006 > [ 0.459970] MSR00000209: 0000000ff0000800 > should be ==> [ 0.459970] MSR00000209: 0000003ff0000800 So detect this borkage and add the prefix 111. Signed-off-by: Yinghai Lu Cc: Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/mtrr/generic.c | 15 +++++++++++++-- 1 file changed, 13 insertions(+), 2 deletions(-) diff --git a/arch/x86/kernel/cpu/mtrr/generic.c b/arch/x86/kernel/cpu/mtrr/generic.c index 509bd3d9eac..43102e03e2d 100644 --- a/arch/x86/kernel/cpu/mtrr/generic.c +++ b/arch/x86/kernel/cpu/mtrr/generic.c @@ -379,6 +379,7 @@ static void generic_get_mtrr(unsigned int reg, unsigned long *base, unsigned long *size, mtrr_type *type) { unsigned int mask_lo, mask_hi, base_lo, base_hi; + unsigned int tmp, hi; rdmsr(MTRRphysMask_MSR(reg), mask_lo, mask_hi); if ((mask_lo & 0x800) == 0) { @@ -392,8 +393,18 @@ static void generic_get_mtrr(unsigned int reg, unsigned long *base, rdmsr(MTRRphysBase_MSR(reg), base_lo, base_hi); /* Work out the shifted address mask. */ - mask_lo = size_or_mask | mask_hi << (32 - PAGE_SHIFT) - | mask_lo >> PAGE_SHIFT; + tmp = mask_hi << (32 - PAGE_SHIFT) | mask_lo >> PAGE_SHIFT; + mask_lo = size_or_mask | tmp; + /* Expand tmp with high bits to all 1s*/ + hi = fls(tmp); + if (hi > 0) { + tmp |= ~((1<<(hi - 1)) - 1); + + if (tmp != mask_lo) { + WARN_ON("mtrr: your BIOS has set up an incorrect mask, fixing it up.\n"); + mask_lo = tmp; + } + } /* This works correctly if size is a power of two, i.e. a contiguous range. */ -- GitLab From 8ae3a5a8dff2c92bd1087bb97c4a3bb61174303e Mon Sep 17 00:00:00 2001 From: Jan Beulich Date: Thu, 21 Aug 2008 14:27:22 +0100 Subject: [PATCH 708/750] x86: fix 1:1 mapping init on 64-bit (memory hotplug case) While I don't have a hotplug capable system at hand, I think two issues need fixing: - pud_phys (in kernel_physical_ampping_init()) would remain uninitialized in the after_bootmem case - the locking done just around phys_pmd_{init,update}() would leave out pgd updates, and it was needlessly covering code portions that do allocations (perhaps using a more friendly gfp value in alloc_low_page() would then be possible) Signed-off-by: Jan Beulich Signed-off-by: Ingo Molnar --- arch/x86/mm/init_64.c | 32 ++++++++++++++++++-------------- 1 file changed, 18 insertions(+), 14 deletions(-) diff --git a/arch/x86/mm/init_64.c b/arch/x86/mm/init_64.c index a87ea0e4b3d..8f487705c3e 100644 --- a/arch/x86/mm/init_64.c +++ b/arch/x86/mm/init_64.c @@ -336,9 +336,12 @@ phys_pmd_init(pmd_t *pmd_page, unsigned long address, unsigned long end, } if (pmd_val(*pmd)) { - if (!pmd_large(*pmd)) + if (!pmd_large(*pmd)) { + spin_lock(&init_mm.page_table_lock); last_map_addr = phys_pte_update(pmd, address, - end); + end); + spin_unlock(&init_mm.page_table_lock); + } /* Count entries we're using from level2_ident_pgt */ if (start == 0) pages++; @@ -347,8 +350,10 @@ phys_pmd_init(pmd_t *pmd_page, unsigned long address, unsigned long end, if (page_size_mask & (1<> PAGE_SHIFT, PAGE_KERNEL_LARGE)); + spin_unlock(&init_mm.page_table_lock); last_map_addr = (address & PMD_MASK) + PMD_SIZE; continue; } @@ -357,7 +362,9 @@ phys_pmd_init(pmd_t *pmd_page, unsigned long address, unsigned long end, last_map_addr = phys_pte_init(pte, address, end); unmap_low_page(pte); + spin_lock(&init_mm.page_table_lock); pmd_populate_kernel(&init_mm, pmd, __va(pte_phys)); + spin_unlock(&init_mm.page_table_lock); } update_page_count(PG_LEVEL_2M, pages); return last_map_addr; @@ -370,9 +377,7 @@ phys_pmd_update(pud_t *pud, unsigned long address, unsigned long end, pmd_t *pmd = pmd_offset(pud, 0); unsigned long last_map_addr; - spin_lock(&init_mm.page_table_lock); last_map_addr = phys_pmd_init(pmd, address, end, page_size_mask); - spin_unlock(&init_mm.page_table_lock); __flush_tlb_all(); return last_map_addr; } @@ -408,20 +413,21 @@ phys_pud_init(pud_t *pud_page, unsigned long addr, unsigned long end, if (page_size_mask & (1<> PAGE_SHIFT, PAGE_KERNEL_LARGE)); + spin_unlock(&init_mm.page_table_lock); last_map_addr = (addr & PUD_MASK) + PUD_SIZE; continue; } pmd = alloc_low_page(&pmd_phys); - - spin_lock(&init_mm.page_table_lock); last_map_addr = phys_pmd_init(pmd, addr, end, page_size_mask); unmap_low_page(pmd); + + spin_lock(&init_mm.page_table_lock); pud_populate(&init_mm, pud, __va(pmd_phys)); spin_unlock(&init_mm.page_table_lock); - } __flush_tlb_all(); update_page_count(PG_LEVEL_1G, pages); @@ -513,16 +519,14 @@ static unsigned long __init kernel_physical_mapping_init(unsigned long start, continue; } - if (after_bootmem) - pud = pud_offset(pgd, start & PGDIR_MASK); - else - pud = alloc_low_page(&pud_phys); - + pud = alloc_low_page(&pud_phys); last_map_addr = phys_pud_init(pud, __pa(start), __pa(next), page_size_mask); unmap_low_page(pud); - pgd_populate(&init_mm, pgd_offset_k(start), - __va(pud_phys)); + + spin_lock(&init_mm.page_table_lock); + pgd_populate(&init_mm, pgd, __va(pud_phys)); + spin_unlock(&init_mm.page_table_lock); } return last_map_addr; -- GitLab From 9482ac6e34dd1890a9a956d460a135bf992cb54a Mon Sep 17 00:00:00 2001 From: Jan Beulich Date: Thu, 21 Aug 2008 14:28:42 +0100 Subject: [PATCH 709/750] x86: fix two modpost warnings in mm/init_64.c early_io{re,un}map() are __init and hence can't be called from __meminit functions. Signed-off-by: Jan Beulich Signed-off-by: Ingo Molnar --- arch/x86/mm/init_64.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/x86/mm/init_64.c b/arch/x86/mm/init_64.c index 8f487705c3e..d3746efb060 100644 --- a/arch/x86/mm/init_64.c +++ b/arch/x86/mm/init_64.c @@ -241,7 +241,7 @@ static unsigned long __initdata table_start; static unsigned long __meminitdata table_end; static unsigned long __meminitdata table_top; -static __meminit void *alloc_low_page(unsigned long *phys) +static __ref void *alloc_low_page(unsigned long *phys) { unsigned long pfn = table_end++; void *adr; @@ -262,7 +262,7 @@ static __meminit void *alloc_low_page(unsigned long *phys) return adr; } -static __meminit void unmap_low_page(void *adr) +static __ref void unmap_low_page(void *adr) { if (after_bootmem) return; -- GitLab From 3a6ddd5f18405ca92e004416af8ed44b9c9783d7 Mon Sep 17 00:00:00 2001 From: Alok Kataria Date: Thu, 21 Aug 2008 11:32:26 -0700 Subject: [PATCH 710/750] x86: fix VMI for early params while fixing a different bug i moved the call to vmi_init before early params could be parsed. This broke the vmi specific commandline parameters. Fix that, by moving vmi initialization after kernel has got a chance to parse early parameters. Signed-off-by: Alok N Kataria Signed-off-by: Ingo Molnar --- arch/x86/kernel/setup.c | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) diff --git a/arch/x86/kernel/setup.c b/arch/x86/kernel/setup.c index a4656adab53..362d4e7f2d3 100644 --- a/arch/x86/kernel/setup.c +++ b/arch/x86/kernel/setup.c @@ -604,14 +604,6 @@ void __init setup_arch(char **cmdline_p) early_cpu_init(); early_ioremap_init(); -#if defined(CONFIG_VMI) && defined(CONFIG_X86_32) - /* - * Must be before kernel pagetables are setup - * or fixmap area is touched. - */ - vmi_init(); -#endif - ROOT_DEV = old_decode_dev(boot_params.hdr.root_dev); screen_info = boot_params.screen_info; edid_info = boot_params.edid_info; @@ -678,6 +670,14 @@ void __init setup_arch(char **cmdline_p) parse_early_param(); +#if defined(CONFIG_VMI) && defined(CONFIG_X86_32) + /* + * Must be before kernel pagetables are setup + * or fixmap area is touched. + */ + vmi_init(); +#endif + /* after early param, so could get panic from serial */ reserve_early_setup_data(); -- GitLab From 05944bdf6fadb5394710269df6770dde447b23ca Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Wed, 13 Aug 2008 20:19:09 +0900 Subject: [PATCH 711/750] libata: implement no[hs]rst force params Implement force params nohrst, nosrst and norst. This is to work around reset related problems and ease debugging. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik --- Documentation/kernel-parameters.txt | 3 ++ drivers/ata/libata-core.c | 46 +++++++++++++++++++---------- drivers/ata/libata-eh.c | 4 +++ include/linux/libata.h | 1 + 4 files changed, 38 insertions(+), 16 deletions(-) diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index a8976467a98..1150444a21a 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -1074,6 +1074,9 @@ and is between 256 and 4096 characters. It is defined in the file * [no]ncq: Turn on or off NCQ. + * nohrst, nosrst, norst: suppress hard, soft + and both resets. + If there are multiple matching configurations changing the same attribute, the last one is used. diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index 5ba96c5052c..dddcb9fde35 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -104,6 +104,7 @@ struct ata_force_param { unsigned long xfer_mask; unsigned int horkage_on; unsigned int horkage_off; + unsigned int lflags; }; struct ata_force_ent { @@ -196,22 +197,23 @@ void ata_force_cbl(struct ata_port *ap) } /** - * ata_force_spd_limit - force SATA spd limit according to libata.force + * ata_force_link_limits - force link limits according to libata.force * @link: ATA link of interest * - * Force SATA spd limit according to libata.force and whine about - * it. When only the port part is specified (e.g. 1:), the limit - * applies to all links connected to both the host link and all - * fan-out ports connected via PMP. If the device part is - * specified as 0 (e.g. 1.00:), it specifies the first fan-out - * link not the host link. Device number 15 always points to the - * host link whether PMP is attached or not. + * Force link flags and SATA spd limit according to libata.force + * and whine about it. When only the port part is specified + * (e.g. 1:), the limit applies to all links connected to both + * the host link and all fan-out ports connected via PMP. If the + * device part is specified as 0 (e.g. 1.00:), it specifies the + * first fan-out link not the host link. Device number 15 always + * points to the host link whether PMP is attached or not. * * LOCKING: * EH context. */ -static void ata_force_spd_limit(struct ata_link *link) +static void ata_force_link_limits(struct ata_link *link) { + bool did_spd = false; int linkno, i; if (ata_is_host_link(link)) @@ -228,13 +230,22 @@ static void ata_force_spd_limit(struct ata_link *link) if (fe->device != -1 && fe->device != linkno) continue; - if (!fe->param.spd_limit) - continue; + /* only honor the first spd limit */ + if (!did_spd && fe->param.spd_limit) { + link->hw_sata_spd_limit = (1 << fe->param.spd_limit) - 1; + ata_link_printk(link, KERN_NOTICE, + "FORCE: PHY spd limit set to %s\n", + fe->param.name); + did_spd = true; + } - link->hw_sata_spd_limit = (1 << fe->param.spd_limit) - 1; - ata_link_printk(link, KERN_NOTICE, - "FORCE: PHY spd limit set to %s\n", fe->param.name); - return; + /* let lflags stack */ + if (fe->param.lflags) { + link->flags |= fe->param.lflags; + ata_link_printk(link, KERN_NOTICE, + "FORCE: link flag 0x%x forced -> 0x%x\n", + fe->param.lflags, link->flags); + } } } @@ -5200,7 +5211,7 @@ int sata_link_init_spd(struct ata_link *link) if (spd) link->hw_sata_spd_limit &= (1 << spd) - 1; - ata_force_spd_limit(link); + ata_force_link_limits(link); link->sata_spd_limit = link->hw_sata_spd_limit; @@ -5991,6 +6002,9 @@ static int __init ata_parse_force_one(char **cur, { "udma133", .xfer_mask = 1 << (ATA_SHIFT_UDMA + 6) }, { "udma/133", .xfer_mask = 1 << (ATA_SHIFT_UDMA + 6) }, { "udma7", .xfer_mask = 1 << (ATA_SHIFT_UDMA + 7) }, + { "nohrst", .lflags = ATA_LFLAG_NO_HRST }, + { "nosrst", .lflags = ATA_LFLAG_NO_SRST }, + { "norst", .lflags = ATA_LFLAG_NO_HRST | ATA_LFLAG_NO_SRST }, }; char *start = *cur, *p = *cur; char *id, *val, *endp; diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c index 58bdc538d22..a570ca47e23 100644 --- a/drivers/ata/libata-eh.c +++ b/drivers/ata/libata-eh.c @@ -2210,6 +2210,10 @@ int ata_eh_reset(struct ata_link *link, int classify, */ while (ata_eh_reset_timeouts[max_tries] != ULONG_MAX) max_tries++; + if (link->flags & ATA_LFLAG_NO_HRST) + hardreset = NULL; + if (link->flags & ATA_LFLAG_NO_SRST) + softreset = NULL; now = jiffies; deadline = ata_deadline(ehc->last_reset, ATA_EH_RESET_COOL_DOWN); diff --git a/include/linux/libata.h b/include/linux/libata.h index 06b80337303..5340d4c83fd 100644 --- a/include/linux/libata.h +++ b/include/linux/libata.h @@ -163,6 +163,7 @@ enum { ATA_DEV_NONE = 9, /* no device */ /* struct ata_link flags */ + ATA_LFLAG_NO_HRST = (1 << 1), /* avoid hardreset */ ATA_LFLAG_NO_SRST = (1 << 2), /* avoid softreset */ ATA_LFLAG_ASSUME_ATA = (1 << 3), /* assume ATA class */ ATA_LFLAG_ASSUME_SEMB = (1 << 4), /* assume SEMB class */ -- GitLab From 4bdee6c5103696a2729d3db2f235d202191788e4 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Wed, 13 Aug 2008 20:24:16 +0900 Subject: [PATCH 712/750] sata_mv: don't issue two DMA commands concurrently sata_mv allowed issuing two DMA commands concurrently which the hardware allows. Unfortunately, libata core layer isn't ready for this yet and spews ugly warning message and malfunctions on this. Don't allow concurrent DMA commands for now. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik --- drivers/ata/sata_mv.c | 34 ++++++++++------------------------ 1 file changed, 10 insertions(+), 24 deletions(-) diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index ad169ffbc4c..80c655f85bc 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -1134,30 +1134,16 @@ static int mv_qc_defer(struct ata_queued_cmd *qc) if (ap->nr_active_links == 0) return 0; - if (pp->pp_flags & MV_PP_FLAG_EDMA_EN) { - /* - * The port is operating in host queuing mode (EDMA). - * It can accomodate a new qc if the qc protocol - * is compatible with the current host queue mode. - */ - if (pp->pp_flags & MV_PP_FLAG_NCQ_EN) { - /* - * The host queue (EDMA) is in NCQ mode. - * If the new qc is also an NCQ command, - * then allow the new qc. - */ - if (qc->tf.protocol == ATA_PROT_NCQ) - return 0; - } else { - /* - * The host queue (EDMA) is in non-NCQ, DMA mode. - * If the new qc is also a non-NCQ, DMA command, - * then allow the new qc. - */ - if (qc->tf.protocol == ATA_PROT_DMA) - return 0; - } - } + /* + * The port is operating in host queuing mode (EDMA) with NCQ + * enabled, allow multiple NCQ commands. EDMA also allows + * queueing multiple DMA commands but libata core currently + * doesn't allow it. + */ + if ((pp->pp_flags & MV_PP_FLAG_EDMA_EN) && + (pp->pp_flags & MV_PP_FLAG_NCQ_EN) && ata_is_ncq(qc->tf.protocol)) + return 0; + return ATA_DEFER_PORT; } -- GitLab From adcb5308dda3d2749342685f23953e13ba74ff68 Mon Sep 17 00:00:00 2001 From: Seth Heasley Date: Mon, 11 Aug 2008 17:03:09 -0700 Subject: [PATCH 713/750] ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDs Resend with proper whitespace. This patch adds the Intel Ibex Peak (PCH) SATA RAID Controller DeviceIDs. Signed-off-by: Seth Heasley Signed-off-by: Jeff Garzik --- drivers/ata/ahci.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c index ef3e5522e1a..a0e85a78778 100644 --- a/drivers/ata/ahci.c +++ b/drivers/ata/ahci.c @@ -486,6 +486,8 @@ static const struct pci_device_id ahci_pci_tbl[] = { { PCI_VDEVICE(INTEL, 0x502b), board_ahci }, /* Tolapai */ { PCI_VDEVICE(INTEL, 0x3a05), board_ahci }, /* ICH10 */ { PCI_VDEVICE(INTEL, 0x3a25), board_ahci }, /* ICH10 */ + { PCI_VDEVICE(INTEL, 0x3b24), board_ahci }, /* PCH RAID */ + { PCI_VDEVICE(INTEL, 0x3b2b), board_ahci }, /* PCH RAID */ /* JMicron 360/1/3/5/6, match class to avoid IDE function */ { PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, -- GitLab From c6c6a1afefe51d488c050464f261d4711bea9a37 Mon Sep 17 00:00:00 2001 From: Seth Heasley Date: Mon, 11 Aug 2008 17:03:18 -0700 Subject: [PATCH 714/750] ata_piix: IDE Mode SATA patch for Intel Ibex Peak DeviceIDs This patch adds the Intel Ibex Peak (PCH) IDE mode SATA Controller DeviceIDs. Signed-off-by: Seth Heasley Signed-off-by: Jeff Garzik --- drivers/ata/ata_piix.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c index c294121fd69..b1d08a8f500 100644 --- a/drivers/ata/ata_piix.c +++ b/drivers/ata/ata_piix.c @@ -275,6 +275,14 @@ static const struct pci_device_id piix_pci_tbl[] = { { 0x8086, 0x3a20, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata }, /* SATA Controller IDE (ICH10) */ { 0x8086, 0x3a26, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata }, + /* SATA Controller IDE (PCH) */ + { 0x8086, 0x3b20, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata }, + /* SATA Controller IDE (PCH) */ + { 0x8086, 0x3b26, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata }, + /* SATA Controller IDE (PCH) */ + { 0x8086, 0x3b2d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata }, + /* SATA Controller IDE (PCH) */ + { 0x8086, 0x3b2e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata }, { } /* terminate list */ }; -- GitLab From eb3a55a9f43f0f8e770c2abf70e65bdda2d5ff1e Mon Sep 17 00:00:00 2001 From: Saeed Bishara Date: Mon, 4 Aug 2008 00:52:55 -1100 Subject: [PATCH 715/750] sata_mv: add the Gen IIE flag to the SoC devices. The SoC sata port is based on the 7042/6042 devices (Gen IIE). This patch will fix various issues when working with PMP and/or NCQ. Signed-off-by: Saeed Bishara Signed-off-by: Jeff Garzik --- drivers/ata/sata_mv.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index 80c655f85bc..13c1d2af18a 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -3022,7 +3022,8 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx) break; case chip_soc: hpriv->ops = &mv_soc_ops; - hp_flags |= MV_HP_FLAG_SOC | MV_HP_ERRATA_60X1C0; + hp_flags |= MV_HP_FLAG_SOC | MV_HP_GEN_IIE | + MV_HP_ERRATA_60X1C0; break; default: -- GitLab From a674050e068a2919908730279f0b731ae6d2e005 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Thu, 31 Jul 2008 16:07:04 +0900 Subject: [PATCH 716/750] libata: fix EH action overwriting in ata_eh_reset() ehc->i.action got accidentally overwritten to ATA_EH_HARD/SOFTRESET in ata_eh_reset(). The original intention was to clear reset action which wasn't selected. This can cause unexpected behavior when other EH actions are scheduled together with reset. Fix it. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik --- drivers/ata/libata-eh.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c index a570ca47e23..c98909ba0b1 100644 --- a/drivers/ata/libata-eh.c +++ b/drivers/ata/libata-eh.c @@ -2251,10 +2251,10 @@ int ata_eh_reset(struct ata_link *link, int classify, ehc->i.action &= ~ATA_EH_RESET; if (hardreset) { reset = hardreset; - ehc->i.action = ATA_EH_HARDRESET; + ehc->i.action |= ATA_EH_HARDRESET; } else if (softreset) { reset = softreset; - ehc->i.action = ATA_EH_SOFTRESET; + ehc->i.action |= ATA_EH_SOFTRESET; } if (prereset) { -- GitLab From 5dbfc9cb59d4ad75199949d7dd8a8c6d7bc518df Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Thu, 31 Jul 2008 16:08:02 +0900 Subject: [PATCH 717/750] libata: always do follow-up SRST if hardreset returned -EAGAIN As an optimization, follow-up SRST used to be skipped if classification wasn't requested even when hardreset requested it via -EAGAIN. However, some hardresets can't wait for device readiness and skipping SRST can cause timeout or other failures during revalidation. Always perform follow-up SRST if hardreset returns -EAGAIN. This makes reset paths more predictable and thus less error-prone. While at it, move hardreset error checking such that it's done right after hardreset is finished. This simplifies followup SRST condition check a bit and makes the reset path easier to modify. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik --- drivers/ata/libata-eh.c | 20 ++++++-------------- 1 file changed, 6 insertions(+), 14 deletions(-) diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c index c98909ba0b1..d4dad47b8f1 100644 --- a/drivers/ata/libata-eh.c +++ b/drivers/ata/libata-eh.c @@ -2171,18 +2171,12 @@ static int ata_do_reset(struct ata_link *link, ata_reset_fn_t reset, } static int ata_eh_followup_srst_needed(struct ata_link *link, - int rc, int classify, - const unsigned int *classes) + int rc, const unsigned int *classes) { if ((link->flags & ATA_LFLAG_NO_SRST) || ata_link_offline(link)) return 0; - if (rc == -EAGAIN) { - if (classify) - return 1; - rc = 0; - } - if (rc != 0) - return 0; + if (rc == -EAGAIN) + return 1; if (sata_pmp_supported(link->ap) && ata_is_host_link(link)) return 1; return 0; @@ -2309,9 +2303,11 @@ int ata_eh_reset(struct ata_link *link, int classify, ehc->i.flags |= ATA_EHI_DID_SOFTRESET; rc = ata_do_reset(link, reset, classes, deadline); + if (rc && rc != -EAGAIN) + goto fail; if (reset == hardreset && - ata_eh_followup_srst_needed(link, rc, classify, classes)) { + ata_eh_followup_srst_needed(link, rc, classes)) { /* okay, let's do follow-up softreset */ reset = softreset; @@ -2326,10 +2322,6 @@ int ata_eh_reset(struct ata_link *link, int classify, ata_eh_about_to_do(link, NULL, ATA_EH_RESET); rc = ata_do_reset(link, reset, classes, deadline); } - - /* -EAGAIN can happen if we skipped followup SRST */ - if (rc && rc != -EAGAIN) - goto fail; } else { if (verbose) ata_link_printk(link, KERN_INFO, "no reset method " -- GitLab From da0e21d3fa2340114fe24821718a1b57123e4664 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Thu, 31 Jul 2008 16:08:38 +0900 Subject: [PATCH 718/750] libata: use ata_link_printk() when printing SError SError belongs to link not port. Use ata_link_printk() to print it. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik --- drivers/ata/libata-eh.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c index d4dad47b8f1..c1db2f234d2 100644 --- a/drivers/ata/libata-eh.c +++ b/drivers/ata/libata-eh.c @@ -2040,7 +2040,7 @@ static void ata_eh_link_report(struct ata_link *link) } if (ehc->i.serror) - ata_port_printk(ap, KERN_ERR, + ata_link_printk(link, KERN_ERR, "SError: { %s%s%s%s%s%s%s%s%s%s%s%s%s%s%s%s%s}\n", ehc->i.serror & SERR_DATA_RECOVERED ? "RecovData " : "", ehc->i.serror & SERR_COMM_RECOVERED ? "RecovComm " : "", -- GitLab From d127ea7b8643a93d14d1f3c542974407f14d3663 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Thu, 31 Jul 2008 16:09:34 +0900 Subject: [PATCH 719/750] libata: restore SControl on detach Save SControl during probing and restore it on detach. This prevents adjustments made by libata drivers to seep into the next driver which gets attached (be it a libata one or not). It's not clear whether SControl also needs to be restored on suspend. The next system to have control (ACPI or kexec'd kernel) would probably like to see the original SControl value but there's no guarantee that a link is gonna keep working after SControl is adjusted without a reset and adding a reset and modified recovery cycle soley for this is an overkill. For now, do it only for detach. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik --- drivers/ata/libata-core.c | 10 +++++----- include/linux/libata.h | 1 + 2 files changed, 6 insertions(+), 5 deletions(-) diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index dddcb9fde35..5f8f57a818f 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -5199,15 +5199,14 @@ void ata_link_init(struct ata_port *ap, struct ata_link *link, int pmp) */ int sata_link_init_spd(struct ata_link *link) { - u32 scontrol; u8 spd; int rc; - rc = sata_scr_read(link, SCR_CONTROL, &scontrol); + rc = sata_scr_read(link, SCR_CONTROL, &link->saved_scontrol); if (rc) return rc; - spd = (scontrol >> 4) & 0xf; + spd = (link->saved_scontrol >> 4) & 0xf; if (spd) link->hw_sata_spd_limit &= (1 << spd) - 1; @@ -5794,9 +5793,10 @@ static void ata_port_detach(struct ata_port *ap) ata_port_wait_eh(ap); /* EH is now guaranteed to see UNLOADING - EH context belongs - * to us. Disable all existing devices. + * to us. Restore SControl and disable all existing devices. */ - ata_port_for_each_link(link, ap) { + __ata_port_for_each_link(link, ap) { + sata_scr_write(link, SCR_CONTROL, link->saved_scontrol); ata_link_for_each_dev(dev, link) ata_dev_disable(dev); } diff --git a/include/linux/libata.h b/include/linux/libata.h index 5340d4c83fd..80233fdc159 100644 --- a/include/linux/libata.h +++ b/include/linux/libata.h @@ -647,6 +647,7 @@ struct ata_link { unsigned int flags; /* ATA_LFLAG_xxx */ + u32 saved_scontrol; /* SControl on probe */ unsigned int hw_sata_spd_limit; unsigned int sata_spd_limit; unsigned int sata_spd; /* current SATA PHY speed */ -- GitLab From ff04715bd5171d6d5c4ddff40c7bdc8d2dc90f7d Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Thu, 31 Jul 2008 18:02:35 +0900 Subject: [PATCH 720/750] pata_via: clean up recent tf_load changes Commit bfce5e0179ad059035df28558724ff60af708e09 implemented custom tf_load for pata_via. This patch cleans it up a bit. * Instead of duplicating whole body, copy tf and set ATA_TFLAG_DEVICE when necessary. * Rename via_ata_tf_load() to via_tf_load(). * No need to set .tf_load in via_port_ops_noirq as it inherits from via_port_ops. * Clean up indentation. Signed-off-by: Tejun Heo Cc: Joseph Chan Signed-off-by: Jeff Garzik --- drivers/ata/pata_via.c | 59 ++++++++---------------------------------- 1 file changed, 11 insertions(+), 48 deletions(-) diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c index 57d951b11f2..8fdb2ce7321 100644 --- a/drivers/ata/pata_via.c +++ b/drivers/ata/pata_via.c @@ -324,62 +324,26 @@ static void via_set_dmamode(struct ata_port *ap, struct ata_device *adev) } /** - * via_ata_sff_tf_load - send taskfile registers to host controller + * via_tf_load - send taskfile registers to host controller * @ap: Port to which output is sent * @tf: ATA taskfile register set * * Outputs ATA taskfile to standard ATA host controller. * * Note: This is to fix the internal bug of via chipsets, which - * will reset the device register after changing the IEN bit on - * ctl register + * will reset the device register after changing the IEN bit on + * ctl register */ -static void via_ata_tf_load(struct ata_port *ap, const struct ata_taskfile *tf) +static void via_tf_load(struct ata_port *ap, const struct ata_taskfile *tf) { - struct ata_ioports *ioaddr = &ap->ioaddr; - unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR; - - if (tf->ctl != ap->last_ctl) { - iowrite8(tf->ctl, ioaddr->ctl_addr); - iowrite8(tf->device, ioaddr->device_addr); - ap->last_ctl = tf->ctl; - ata_wait_idle(ap); - } - - if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) { - iowrite8(tf->hob_feature, ioaddr->feature_addr); - iowrite8(tf->hob_nsect, ioaddr->nsect_addr); - iowrite8(tf->hob_lbal, ioaddr->lbal_addr); - iowrite8(tf->hob_lbam, ioaddr->lbam_addr); - iowrite8(tf->hob_lbah, ioaddr->lbah_addr); - VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n", - tf->hob_feature, - tf->hob_nsect, - tf->hob_lbal, - tf->hob_lbam, - tf->hob_lbah); - } + struct ata_taskfile tmp_tf; - if (is_addr) { - iowrite8(tf->feature, ioaddr->feature_addr); - iowrite8(tf->nsect, ioaddr->nsect_addr); - iowrite8(tf->lbal, ioaddr->lbal_addr); - iowrite8(tf->lbam, ioaddr->lbam_addr); - iowrite8(tf->lbah, ioaddr->lbah_addr); - VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n", - tf->feature, - tf->nsect, - tf->lbal, - tf->lbam, - tf->lbah); + if (ap->ctl != ap->last_ctl && !(tf->flags & ATA_TFLAG_DEVICE)) { + tmp_tf = *tf; + tmp_tf.flags |= ATA_TFLAG_DEVICE; + tf = &tmp_tf; } - - if (tf->flags & ATA_TFLAG_DEVICE) { - iowrite8(tf->device, ioaddr->device_addr); - VPRINTK("device 0x%X\n", tf->device); - } - - ata_wait_idle(ap); + ata_sff_tf_load(ap, tf); } static struct scsi_host_template via_sht = { @@ -392,13 +356,12 @@ static struct ata_port_operations via_port_ops = { .set_piomode = via_set_piomode, .set_dmamode = via_set_dmamode, .prereset = via_pre_reset, - .sff_tf_load = via_ata_tf_load, + .sff_tf_load = via_tf_load, }; static struct ata_port_operations via_port_ops_noirq = { .inherits = &via_port_ops, .sff_data_xfer = ata_sff_data_xfer_noirq, - .sff_tf_load = via_ata_tf_load, }; /** -- GitLab From 20e2de4a505aa02131a95665e8920eb053fce686 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Fri, 1 Aug 2008 12:51:43 +0900 Subject: [PATCH 721/750] ahci: sis controllers actually can do PMP SIS controllers were blacklisted for PMP as enabling it made device detection fail whether the device was PMP or not - the natural conclusion was the controller chokes on SRST w/ pmp==15. However, it turned out that the controller just didn't like issuing SRST after hardreset w/o clearing SError first. Interestingly, the SRST itself succeeds but the following commands fail. If SError is cleared between hardreset and SRST, which is the default behavior now, everything works fine and SIS controllers work with PMPs happily. Remove PMP blacklisting for SIS AHCIs. Signed-off-by: Tejun Heo Cc: Piter PUNK Signed-off-by: Jeff Garzik --- drivers/ata/ahci.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c index a0e85a78778..c729e6988bb 100644 --- a/drivers/ata/ahci.c +++ b/drivers/ata/ahci.c @@ -577,9 +577,9 @@ static const struct pci_device_id ahci_pci_tbl[] = { { PCI_VDEVICE(NVIDIA, 0x0bc7), board_ahci }, /* MCP7B */ /* SiS */ - { PCI_VDEVICE(SI, 0x1184), board_ahci_nopmp }, /* SiS 966 */ - { PCI_VDEVICE(SI, 0x1185), board_ahci_nopmp }, /* SiS 968 */ - { PCI_VDEVICE(SI, 0x0186), board_ahci_nopmp }, /* SiS 968 */ + { PCI_VDEVICE(SI, 0x1184), board_ahci }, /* SiS 966 */ + { PCI_VDEVICE(SI, 0x1185), board_ahci }, /* SiS 968 */ + { PCI_VDEVICE(SI, 0x0186), board_ahci }, /* SiS 968 */ /* Marvell */ { PCI_VDEVICE(MARVELL, 0x6145), board_ahci_mv }, /* 6145 */ -- GitLab From b15b3ebae102f89c25ccbcae0b2099af312f2e82 Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Fri, 1 Aug 2008 09:18:34 +0100 Subject: [PATCH 722/750] libata: Fix a large collection of DMA mode mismatches MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Dave Müller sent a diff for the pata_oldpiix that highlighted a problem where a lot of the ATA drivers assume dma_mode == 0 means "no DMA" while the core code uses 0xFF. This turns out to have other consequences such as code doing >= XFER_UDMA_0 also catching 0xFF as UDMAlots. Fortunately it doesn't generally affect set_dma_mode, although some drivers call back into their own set mode code from other points. Having been through the drivers I've added helpers for using_udma/using_mwdma dma_enabled so that people don't open code ranges that may change (eg if UDMA8 appears somewhere) Thanks to David for the initial bits [and added fix for pata_oldpiix from and signed-off-by Dave Mueller -jg] Signed-off-by: Alan Cox Signed-off-by: Jeff Garzik --- drivers/ata/libata-core.c | 4 ++-- drivers/ata/pata_acpi.c | 2 +- drivers/ata/pata_atiixp.c | 2 +- drivers/ata/pata_cs5530.c | 6 +++--- drivers/ata/pata_oldpiix.c | 2 +- drivers/ata/pata_sc1200.c | 6 +++--- include/linux/libata.h | 22 ++++++++++++++++++++++ 7 files changed, 33 insertions(+), 11 deletions(-) diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index 5f8f57a818f..79e3a8e7a84 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -3288,7 +3288,7 @@ int ata_do_set_mode(struct ata_link *link, struct ata_device **r_failed_dev) dev->dma_mode = ata_xfer_mask2mode(dma_mask); found = 1; - if (dev->dma_mode != 0xff) + if (ata_dma_enabled(dev)) used_dma = 1; } if (!found) @@ -3313,7 +3313,7 @@ int ata_do_set_mode(struct ata_link *link, struct ata_device **r_failed_dev) /* step 3: set host DMA timings */ ata_link_for_each_dev(dev, link) { - if (!ata_dev_enabled(dev) || dev->dma_mode == 0xff) + if (!ata_dev_enabled(dev) || !ata_dma_enabled(dev)) continue; dev->xfer_mode = dev->dma_mode; diff --git a/drivers/ata/pata_acpi.c b/drivers/ata/pata_acpi.c index fbe60571155..eb919c16a03 100644 --- a/drivers/ata/pata_acpi.c +++ b/drivers/ata/pata_acpi.c @@ -181,7 +181,7 @@ static unsigned int pacpi_qc_issue(struct ata_queued_cmd *qc) if (adev != acpi->last) { pacpi_set_piomode(ap, adev); - if (adev->dma_mode) + if (ata_dma_enabled(adev)) pacpi_set_dmamode(ap, adev); acpi->last = adev; } diff --git a/drivers/ata/pata_atiixp.c b/drivers/ata/pata_atiixp.c index d7de7baf58a..e8a0d99d735 100644 --- a/drivers/ata/pata_atiixp.c +++ b/drivers/ata/pata_atiixp.c @@ -183,7 +183,7 @@ static void atiixp_bmdma_start(struct ata_queued_cmd *qc) u16 tmp16; pci_read_config_word(pdev, ATIIXP_IDE_UDMA_CONTROL, &tmp16); - if (adev->dma_mode >= XFER_UDMA_0) + if (ata_using_udma(adev)) tmp16 |= (1 << dn); else tmp16 &= ~(1 << dn); diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c index 744beebaaf4..0c4b271a9d5 100644 --- a/drivers/ata/pata_cs5530.c +++ b/drivers/ata/pata_cs5530.c @@ -149,10 +149,10 @@ static unsigned int cs5530_qc_issue(struct ata_queued_cmd *qc) struct ata_device *prev = ap->private_data; /* See if the DMA settings could be wrong */ - if (adev->dma_mode != 0 && adev != prev && prev != NULL) { + if (ata_dma_enabled(adev) && adev != prev && prev != NULL) { /* Maybe, but do the channels match MWDMA/UDMA ? */ - if ((adev->dma_mode >= XFER_UDMA_0 && prev->dma_mode < XFER_UDMA_0) || - (adev->dma_mode < XFER_UDMA_0 && prev->dma_mode >= XFER_UDMA_0)) + if ((ata_using_udma(adev) && !ata_using_udma(prev)) || + (ata_using_udma(prev) && !ata_using_udma(adev))) /* Switch the mode bits */ cs5530_set_dmamode(ap, adev); } diff --git a/drivers/ata/pata_oldpiix.c b/drivers/ata/pata_oldpiix.c index e678af383d1..df64f244300 100644 --- a/drivers/ata/pata_oldpiix.c +++ b/drivers/ata/pata_oldpiix.c @@ -198,7 +198,7 @@ static unsigned int oldpiix_qc_issue(struct ata_queued_cmd *qc) if (adev != ap->private_data) { oldpiix_set_piomode(ap, adev); - if (adev->dma_mode) + if (ata_dma_enabled(adev)) oldpiix_set_dmamode(ap, adev); } return ata_sff_qc_issue(qc); diff --git a/drivers/ata/pata_sc1200.c b/drivers/ata/pata_sc1200.c index cbab397e3db..0278fd2b8fb 100644 --- a/drivers/ata/pata_sc1200.c +++ b/drivers/ata/pata_sc1200.c @@ -167,10 +167,10 @@ static unsigned int sc1200_qc_issue(struct ata_queued_cmd *qc) struct ata_device *prev = ap->private_data; /* See if the DMA settings could be wrong */ - if (adev->dma_mode != 0 && adev != prev && prev != NULL) { + if (ata_dma_enabled(adev) && adev != prev && prev != NULL) { /* Maybe, but do the channels match MWDMA/UDMA ? */ - if ((adev->dma_mode >= XFER_UDMA_0 && prev->dma_mode < XFER_UDMA_0) || - (adev->dma_mode < XFER_UDMA_0 && prev->dma_mode >= XFER_UDMA_0)) + if ((ata_using_udma(adev) && !ata_using_udma(prev)) || + (ata_using_udma(prev) && !ata_using_udma(adev))) /* Switch the mode bits */ sc1200_set_dmamode(ap, adev); } diff --git a/include/linux/libata.h b/include/linux/libata.h index 80233fdc159..225bfc5bd9e 100644 --- a/include/linux/libata.h +++ b/include/linux/libata.h @@ -1429,6 +1429,28 @@ static inline unsigned long ata_deadline(unsigned long from_jiffies, return from_jiffies + msecs_to_jiffies(timeout_msecs); } +/* Don't open code these in drivers as there are traps. Firstly the range may + change in future hardware and specs, secondly 0xFF means 'no DMA' but is + > UDMA_0. Dyma ddreigiau */ + +static inline int ata_using_mwdma(struct ata_device *adev) +{ + if (adev->dma_mode >= XFER_MW_DMA_0 && adev->dma_mode <= XFER_MW_DMA_4) + return 1; + return 0; +} + +static inline int ata_using_udma(struct ata_device *adev) +{ + if (adev->dma_mode >= XFER_UDMA_0 && adev->dma_mode <= XFER_UDMA_7) + return 1; + return 0; +} + +static inline int ata_dma_enabled(struct ata_device *adev) +{ + return (adev->dma_mode == 0xFF ? 0 : 1); +} /************************************************************************** * PMP - drivers/ata/libata-pmp.c -- GitLab From 4ef281853474389fea952e9e59650e599ecf2d62 Mon Sep 17 00:00:00 2001 From: Jeff Garzik Date: Fri, 22 Aug 2008 02:33:23 -0400 Subject: [PATCH 723/750] [libata] pata_it821x: fix warning Reported by Andrew Morton: drivers/ata/pata_it821x.c: In function 'it821x_port_start': drivers/ata/pata_it821x.c:609: warning: 'mtype' may be used uninitialized in this function Pretty horrid fix, but so's a warning.. Signed-off-by: Jeff Garzik --- drivers/ata/pata_it821x.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/ata/pata_it821x.c b/drivers/ata/pata_it821x.c index 27843c70eb9..0221c9a4676 100644 --- a/drivers/ata/pata_it821x.c +++ b/drivers/ata/pata_it821x.c @@ -606,7 +606,7 @@ static void it821x_display_disk(int n, u8 *buf) { unsigned char id[41]; int mode = 0; - char *mtype; + char *mtype = ""; char mbuf[8]; char *cbl = "(40 wire cable)"; -- GitLab From f6e0b239a2657ea8cb67f0d83d0bfdbfd19a481b Mon Sep 17 00:00:00 2001 From: Jarek Poplawski Date: Fri, 22 Aug 2008 03:24:05 -0700 Subject: [PATCH 724/750] pkt_sched: Fix qdisc list locking Since some qdiscs call qdisc_tree_decrease_qlen() (so qdisc_lookup()) without rtnl_lock(), adding and deleting from a qdisc list needs additional locking. This patch adds global spinlock qdisc_list_lock and wrapper functions for modifying the list. It is considered as a temporary solution until hfsc_dequeue(), netem_dequeue() and tbf_dequeue() (or qdisc_tree_decrease_qlen()) are redone. With feedback from Herbert Xu and David S. Miller. Signed-off-by: Jarek Poplawski Acked-by: Herbert Xu Signed-off-by: David S. Miller --- include/net/pkt_sched.h | 1 + net/sched/sch_api.c | 44 ++++++++++++++++++++++++++++++++++++----- net/sched/sch_generic.c | 5 ++--- 3 files changed, 42 insertions(+), 8 deletions(-) diff --git a/include/net/pkt_sched.h b/include/net/pkt_sched.h index 853fe83d9f3..b786a5b0925 100644 --- a/include/net/pkt_sched.h +++ b/include/net/pkt_sched.h @@ -78,6 +78,7 @@ extern struct Qdisc *fifo_create_dflt(struct Qdisc *sch, struct Qdisc_ops *ops, extern int register_qdisc(struct Qdisc_ops *qops); extern int unregister_qdisc(struct Qdisc_ops *qops); +extern void qdisc_list_del(struct Qdisc *q); extern struct Qdisc *qdisc_lookup(struct net_device *dev, u32 handle); extern struct Qdisc *qdisc_lookup_class(struct net_device *dev, u32 handle); extern struct qdisc_rate_table *qdisc_get_rtab(struct tc_ratespec *r, diff --git a/net/sched/sch_api.c b/net/sched/sch_api.c index 45f442d7de4..e7fb9e0d21b 100644 --- a/net/sched/sch_api.c +++ b/net/sched/sch_api.c @@ -199,19 +199,53 @@ struct Qdisc *qdisc_match_from_root(struct Qdisc *root, u32 handle) return NULL; } +/* + * This lock is needed until some qdiscs stop calling qdisc_tree_decrease_qlen() + * without rtnl_lock(); currently hfsc_dequeue(), netem_dequeue(), tbf_dequeue() + */ +static DEFINE_SPINLOCK(qdisc_list_lock); + +static void qdisc_list_add(struct Qdisc *q) +{ + if ((q->parent != TC_H_ROOT) && !(q->flags & TCQ_F_INGRESS)) { + spin_lock_bh(&qdisc_list_lock); + list_add_tail(&q->list, &qdisc_root_sleeping(q)->list); + spin_unlock_bh(&qdisc_list_lock); + } +} + +void qdisc_list_del(struct Qdisc *q) +{ + if ((q->parent != TC_H_ROOT) && !(q->flags & TCQ_F_INGRESS)) { + spin_lock_bh(&qdisc_list_lock); + list_del(&q->list); + spin_unlock_bh(&qdisc_list_lock); + } +} +EXPORT_SYMBOL(qdisc_list_del); + struct Qdisc *qdisc_lookup(struct net_device *dev, u32 handle) { unsigned int i; + struct Qdisc *q; + + spin_lock_bh(&qdisc_list_lock); for (i = 0; i < dev->num_tx_queues; i++) { struct netdev_queue *txq = netdev_get_tx_queue(dev, i); - struct Qdisc *q, *txq_root = txq->qdisc_sleeping; + struct Qdisc *txq_root = txq->qdisc_sleeping; q = qdisc_match_from_root(txq_root, handle); if (q) - return q; + goto unlock; } - return qdisc_match_from_root(dev->rx_queue.qdisc_sleeping, handle); + + q = qdisc_match_from_root(dev->rx_queue.qdisc_sleeping, handle); + +unlock: + spin_unlock_bh(&qdisc_list_lock); + + return q; } static struct Qdisc *qdisc_leaf(struct Qdisc *p, u32 classid) @@ -810,8 +844,8 @@ qdisc_create(struct net_device *dev, struct netdev_queue *dev_queue, goto err_out3; } } - if ((parent != TC_H_ROOT) && !(sch->flags & TCQ_F_INGRESS)) - list_add_tail(&sch->list, &dev_queue->qdisc_sleeping->list); + + qdisc_list_add(sch); return sch; } diff --git a/net/sched/sch_generic.c b/net/sched/sch_generic.c index c3ed4d44fc1..5f0ade7806a 100644 --- a/net/sched/sch_generic.c +++ b/net/sched/sch_generic.c @@ -526,10 +526,9 @@ void qdisc_destroy(struct Qdisc *qdisc) !atomic_dec_and_test(&qdisc->refcnt)) return; - if (qdisc->parent) - list_del(&qdisc->list); - #ifdef CONFIG_NET_SCHED + qdisc_list_del(qdisc); + qdisc_put_stab(qdisc->stab); #endif gen_kill_estimator(&qdisc->bstats, &qdisc->rate_est); -- GitLab From c4bd1fdab0deec0f69aeabab22075cb22ac8ad44 Mon Sep 17 00:00:00 2001 From: Marcin Slusarz Date: Thu, 21 Aug 2008 20:49:05 +0200 Subject: [PATCH 725/750] x86: fix section mismatch warning - uv_cpu_init WARNING: vmlinux.o(.cpuinit.text+0x3cc4): Section mismatch in reference from the function uv_cpu_init() to the function .init.text:uv_system_init() The function __cpuinit uv_cpu_init() references a function __init uv_system_init(). If uv_system_init is only used by uv_cpu_init then annotate uv_system_init with a matching annotation. uv_system_init was ment to be called only once, so do it from codepath (native_smp_prepare_cpus) which is called once, right before activation of other cpus (smp_init). Note: old code relied on uv_node_to_blade being initialized to 0, but it'a not initialized from anywhere. Signed-off-by: Marcin Slusarz Acked-by: Jack Steiner Signed-off-by: Ingo Molnar --- arch/x86/kernel/genx2apic_uv_x.c | 8 +++++--- arch/x86/kernel/smpboot.c | 3 +++ include/asm-x86/genapic_32.h | 1 + include/asm-x86/genapic_64.h | 1 + 4 files changed, 10 insertions(+), 3 deletions(-) diff --git a/arch/x86/kernel/genx2apic_uv_x.c b/arch/x86/kernel/genx2apic_uv_x.c index 2d7e307c777..bfa837cb16b 100644 --- a/arch/x86/kernel/genx2apic_uv_x.c +++ b/arch/x86/kernel/genx2apic_uv_x.c @@ -293,7 +293,9 @@ static __init void uv_rtc_init(void) sn_rtc_cycles_per_second = ticks_per_sec; } -static __init void uv_system_init(void) +static bool uv_system_inited; + +void __init uv_system_init(void) { union uvh_si_addr_map_config_u m_n_config; union uvh_node_id_u node_id; @@ -383,6 +385,7 @@ static __init void uv_system_init(void) map_mmr_high(max_pnode); map_config_high(max_pnode); map_mmioh_high(max_pnode); + uv_system_inited = true; } /* @@ -391,8 +394,7 @@ static __init void uv_system_init(void) */ void __cpuinit uv_cpu_init(void) { - if (!uv_node_to_blade) - uv_system_init(); + BUG_ON(!uv_system_inited); uv_blade_info[uv_numa_blade_id()].nr_online_cpus++; diff --git a/arch/x86/kernel/smpboot.c b/arch/x86/kernel/smpboot.c index e139e617f42..7985c5b3f91 100644 --- a/arch/x86/kernel/smpboot.c +++ b/arch/x86/kernel/smpboot.c @@ -1221,6 +1221,9 @@ void __init native_smp_prepare_cpus(unsigned int max_cpus) printk(KERN_INFO "CPU%d: ", 0); print_cpu_info(&cpu_data(0)); setup_boot_clock(); + + if (is_uv_system()) + uv_system_init(); out: preempt_enable(); } diff --git a/include/asm-x86/genapic_32.h b/include/asm-x86/genapic_32.h index b02ea6e17de..754d635f90f 100644 --- a/include/asm-x86/genapic_32.h +++ b/include/asm-x86/genapic_32.h @@ -118,6 +118,7 @@ enum uv_system_type {UV_NONE, UV_LEGACY_APIC, UV_X2APIC, UV_NON_UNIQUE_APIC}; #define get_uv_system_type() UV_NONE #define is_uv_system() 0 #define uv_wakeup_secondary(a, b) 1 +#define uv_system_init() do {} while (0) #endif diff --git a/include/asm-x86/genapic_64.h b/include/asm-x86/genapic_64.h index 0f8504627c4..a47d6312913 100644 --- a/include/asm-x86/genapic_64.h +++ b/include/asm-x86/genapic_64.h @@ -42,6 +42,7 @@ extern int is_uv_system(void); extern struct genapic apic_x2apic_uv_x; DECLARE_PER_CPU(int, x2apic_extra_bits); extern void uv_cpu_init(void); +extern void uv_system_init(void); extern int uv_wakeup_secondary(int phys_apicid, unsigned int start_rip); extern void setup_apic_routing(void); -- GitLab From 9754a5b840a209bc1f192d59f63e81b698a55ac8 Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Fri, 22 Aug 2008 08:22:23 +0200 Subject: [PATCH 726/750] x86: work around MTRR mask setting, v2 improve the debug printout: - make it actually display something - print it only once would be nice to have a WARN_ONCE() facility, to feed such things to kerneloops.org. Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/mtrr/generic.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/arch/x86/kernel/cpu/mtrr/generic.c b/arch/x86/kernel/cpu/mtrr/generic.c index 43102e03e2d..cb7d3b6a80e 100644 --- a/arch/x86/kernel/cpu/mtrr/generic.c +++ b/arch/x86/kernel/cpu/mtrr/generic.c @@ -401,7 +401,12 @@ static void generic_get_mtrr(unsigned int reg, unsigned long *base, tmp |= ~((1<<(hi - 1)) - 1); if (tmp != mask_lo) { - WARN_ON("mtrr: your BIOS has set up an incorrect mask, fixing it up.\n"); + static int once = 1; + + if (once) { + printk(KERN_INFO "mtrr: your BIOS has set up an incorrect mask, fixing it up.\n"); + once = 0; + } mask_lo = tmp; } } -- GitLab From 1082c7487cbe5a40755ba9e33552b6ecbf419bf2 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Fri, 22 Aug 2008 15:24:22 +0200 Subject: [PATCH 727/750] ALSA: hda - Fix call of alc888_coef_init() Using init_hook to call alc888_coef_init() is problematic for configurations that already set another init_hook. Better to put it in alc_init() as is (although it looks a bit hackish). Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_realtek.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index b80e725432f..909f1c101c9 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -952,7 +952,7 @@ do_sku: tmp | 0x2010); break; case 0x10ec0888: - alc888_coef_init(codec); + /*alc888_coef_init(codec);*/ /* called in alc_init() */ break; case 0x10ec0267: case 0x10ec0268: @@ -2439,6 +2439,8 @@ static int alc_init(struct hda_codec *codec) unsigned int i; alc_fix_pll(codec); + if (codec->vendor_id == 0x10ec0888) + alc888_coef_init(codec); for (i = 0; i < spec->num_init_verbs; i++) snd_hda_sequence_write(codec, spec->init_verbs[i]); @@ -8426,8 +8428,6 @@ static int patch_alc883(struct hda_codec *codec) codec->patch_ops = alc_patch_ops; if (board_config == ALC883_AUTO) spec->init_hook = alc883_auto_init; - else if (codec->vendor_id == 0x10ec0888) - spec->init_hook = alc888_coef_init; #ifdef CONFIG_SND_HDA_POWER_SAVE if (!spec->loopback.amplist) -- GitLab From a697690bece75d4ba424c1318eb25c37d41d5829 Mon Sep 17 00:00:00 2001 From: Herbert Xu Date: Sat, 23 Aug 2008 01:04:06 +1000 Subject: [PATCH 728/750] crypto: authenc - Avoid using clobbered request pointer Authenc works in two stages for encryption, it first encrypts and then computes an ICV. The context memory of the request is used by both operations. The problem is that when an asynchronous encryption completes, we will compute the ICV and then reread the context memory of the encryption to get the original request. It just happens that we have a buffer of 16 bytes in front of the request pointer, so ICVs of 16 bytes (such as SHA1) do not trigger the bug. However, any attempt to uses a larger ICV instantly kills the machine when the first asynchronous encryption is completed. This patch fixes this by saving the request pointer before we start the ICV computation. Signed-off-by: Herbert Xu --- crypto/authenc.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-) diff --git a/crypto/authenc.c b/crypto/authenc.c index 4b226768752..fd9f06c63d7 100644 --- a/crypto/authenc.c +++ b/crypto/authenc.c @@ -174,8 +174,9 @@ static int crypto_authenc_genicv(struct aead_request *req, u8 *iv, static void crypto_authenc_encrypt_done(struct crypto_async_request *req, int err) { + struct aead_request *areq = req->data; + if (!err) { - struct aead_request *areq = req->data; struct crypto_aead *authenc = crypto_aead_reqtfm(areq); struct crypto_authenc_ctx *ctx = crypto_aead_ctx(authenc); struct ablkcipher_request *abreq = aead_request_ctx(areq); @@ -185,7 +186,7 @@ static void crypto_authenc_encrypt_done(struct crypto_async_request *req, err = crypto_authenc_genicv(areq, iv, 0); } - aead_request_complete(req->data, err); + aead_request_complete(areq, err); } static int crypto_authenc_encrypt(struct aead_request *req) @@ -216,14 +217,15 @@ static int crypto_authenc_encrypt(struct aead_request *req) static void crypto_authenc_givencrypt_done(struct crypto_async_request *req, int err) { + struct aead_request *areq = req->data; + if (!err) { - struct aead_request *areq = req->data; struct skcipher_givcrypt_request *greq = aead_request_ctx(areq); err = crypto_authenc_genicv(areq, greq->giv, 0); } - aead_request_complete(req->data, err); + aead_request_complete(areq, err); } static int crypto_authenc_givencrypt(struct aead_givcrypt_request *req) -- GitLab From fdc0bde90a689b9145f2b6f271c03f4c99d09667 Mon Sep 17 00:00:00 2001 From: "Denis V. Lunev" Date: Sat, 23 Aug 2008 04:43:33 -0700 Subject: [PATCH 729/750] icmp: icmp_sk() should not use smp_processor_id() in preemptible code Pass namespace into icmp_xmit_lock, obtain socket inside and return it as a result for caller. Thanks Alexey Dobryan for this report: Steps to reproduce: CONFIG_PREEMPT=y CONFIG_DEBUG_PREEMPT=y tracepath BUG: using smp_processor_id() in preemptible [00000000] code: tracepath/3205 caller is icmp_sk+0x15/0x30 Pid: 3205, comm: tracepath Not tainted 2.6.27-rc4 #1 Call Trace: [] debug_smp_processor_id+0xe4/0xf0 [] icmp_sk+0x15/0x30 [] icmp_send+0x4b/0x3f0 [] ? trace_hardirqs_on_caller+0xd5/0x160 [] ? trace_hardirqs_on+0xd/0x10 [] ? local_bh_enable_ip+0x95/0x110 [] ? _spin_unlock_bh+0x39/0x40 [] ? mark_held_locks+0x4c/0x90 [] ? trace_hardirqs_on+0xd/0x10 [] ? trace_hardirqs_on_caller+0xd5/0x160 [] ip_fragment+0x8d4/0x900 [] ? ip_finish_output2+0x0/0x290 [] ? ip_finish_output+0x0/0x60 [] ? dst_output+0x0/0x10 [] ip_finish_output+0x4c/0x60 [] ip_output+0xa3/0xf0 [] ip_local_out+0x20/0x30 [] ip_push_pending_frames+0x27f/0x400 [] udp_push_pending_frames+0x233/0x3d0 [] udp_sendmsg+0x321/0x6f0 [] inet_sendmsg+0x45/0x80 [] sock_sendmsg+0xdf/0x110 [] ? autoremove_wake_function+0x0/0x40 [] ? validate_chain+0x415/0x1010 [] ? __do_fault+0x140/0x450 [] ? __lock_acquire+0x260/0x590 [] ? sockfd_lookup_light+0x45/0x80 [] sys_sendto+0xea/0x120 [] ? _spin_unlock_irqrestore+0x42/0x80 [] ? __up_read+0x4c/0xb0 [] ? up_read+0x26/0x30 [] system_call_fastpath+0x16/0x1b icmp6_sk() is similar. Signed-off-by: Denis V. Lunev Signed-off-by: David S. Miller --- net/ipv4/icmp.c | 22 ++++++++++++++-------- net/ipv6/icmp.c | 23 ++++++++++++----------- 2 files changed, 26 insertions(+), 19 deletions(-) diff --git a/net/ipv4/icmp.c b/net/ipv4/icmp.c index 860558633b2..55c355e6323 100644 --- a/net/ipv4/icmp.c +++ b/net/ipv4/icmp.c @@ -204,18 +204,22 @@ static struct sock *icmp_sk(struct net *net) return net->ipv4.icmp_sk[smp_processor_id()]; } -static inline int icmp_xmit_lock(struct sock *sk) +static inline struct sock *icmp_xmit_lock(struct net *net) { + struct sock *sk; + local_bh_disable(); + sk = icmp_sk(net); + if (unlikely(!spin_trylock(&sk->sk_lock.slock))) { /* This can happen if the output path signals a * dst_link_failure() for an outgoing ICMP packet. */ local_bh_enable(); - return 1; + return NULL; } - return 0; + return sk; } static inline void icmp_xmit_unlock(struct sock *sk) @@ -354,15 +358,17 @@ static void icmp_reply(struct icmp_bxm *icmp_param, struct sk_buff *skb) struct ipcm_cookie ipc; struct rtable *rt = skb->rtable; struct net *net = dev_net(rt->u.dst.dev); - struct sock *sk = icmp_sk(net); - struct inet_sock *inet = inet_sk(sk); + struct sock *sk; + struct inet_sock *inet; __be32 daddr; if (ip_options_echo(&icmp_param->replyopts, skb)) return; - if (icmp_xmit_lock(sk)) + sk = icmp_xmit_lock(net); + if (sk == NULL) return; + inet = inet_sk(sk); icmp_param->data.icmph.checksum = 0; @@ -419,7 +425,6 @@ void icmp_send(struct sk_buff *skb_in, int type, int code, __be32 info) if (!rt) goto out; net = dev_net(rt->u.dst.dev); - sk = icmp_sk(net); /* * Find the original header. It is expected to be valid, of course. @@ -483,7 +488,8 @@ void icmp_send(struct sk_buff *skb_in, int type, int code, __be32 info) } } - if (icmp_xmit_lock(sk)) + sk = icmp_xmit_lock(net); + if (sk == NULL) return; /* diff --git a/net/ipv6/icmp.c b/net/ipv6/icmp.c index abedf95fdf2..b3157a0cc15 100644 --- a/net/ipv6/icmp.c +++ b/net/ipv6/icmp.c @@ -91,19 +91,22 @@ static struct inet6_protocol icmpv6_protocol = { .flags = INET6_PROTO_NOPOLICY|INET6_PROTO_FINAL, }; -static __inline__ int icmpv6_xmit_lock(struct sock *sk) +static __inline__ struct sock *icmpv6_xmit_lock(struct net *net) { + struct sock *sk; + local_bh_disable(); + sk = icmpv6_sk(net); if (unlikely(!spin_trylock(&sk->sk_lock.slock))) { /* This can happen if the output path (f.e. SIT or * ip6ip6 tunnel) signals dst_link_failure() for an * outgoing ICMP6 packet. */ local_bh_enable(); - return 1; + return NULL; } - return 0; + return sk; } static __inline__ void icmpv6_xmit_unlock(struct sock *sk) @@ -392,11 +395,10 @@ void icmpv6_send(struct sk_buff *skb, int type, int code, __u32 info, fl.fl_icmp_code = code; security_skb_classify_flow(skb, &fl); - sk = icmpv6_sk(net); - np = inet6_sk(sk); - - if (icmpv6_xmit_lock(sk)) + sk = icmpv6_xmit_lock(net); + if (sk == NULL) return; + np = inet6_sk(sk); if (!icmpv6_xrlim_allow(sk, type, &fl)) goto out; @@ -539,11 +541,10 @@ static void icmpv6_echo_reply(struct sk_buff *skb) fl.fl_icmp_type = ICMPV6_ECHO_REPLY; security_skb_classify_flow(skb, &fl); - sk = icmpv6_sk(net); - np = inet6_sk(sk); - - if (icmpv6_xmit_lock(sk)) + sk = icmpv6_xmit_lock(net); + if (sk == NULL) return; + np = inet6_sk(sk); if (!fl.oif && ipv6_addr_is_multicast(&fl.fl6_dst)) fl.oif = np->mcast_oif; -- GitLab From f410a1fba7afa79d2992620e874a343fdba28332 Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Sat, 23 Aug 2008 05:16:46 -0700 Subject: [PATCH 730/750] ipv6: protocol for address routes This fixes a problem spotted with zebra, but not sure if it is necessary a kernel problem. With IPV6 when an address is added to an interface, Zebra creates a duplicate RIB entry, one as a connected route, and other as a kernel route. When an address is added to an interface the RTN_NEWADDR message causes Zebra to create a connected route. In IPV4 when an address is added to an interface a RTN_NEWROUTE message is set to user space with the protocol RTPROT_KERNEL. Zebra ignores these messages, because it already has the connected route. The problem is that route created in IPV6 has route protocol == RTPROT_BOOT. Was this a design decision or a bug? This fixes it. Same patch applies to both net-2.6 and stable. Signed-off-by: Stephen Hemminger Signed-off-by: David S. Miller --- net/ipv6/addrconf.c | 1 + 1 file changed, 1 insertion(+) diff --git a/net/ipv6/addrconf.c b/net/ipv6/addrconf.c index e2d3b7580b7..7b6a584b62d 100644 --- a/net/ipv6/addrconf.c +++ b/net/ipv6/addrconf.c @@ -1688,6 +1688,7 @@ addrconf_prefix_route(struct in6_addr *pfx, int plen, struct net_device *dev, .fc_dst_len = plen, .fc_flags = RTF_UP | flags, .fc_nlinfo.nl_net = dev_net(dev), + .fc_protocol = RTPROT_KERNEL, }; ipv6_addr_copy(&cfg.fc_dst, pfx); -- GitLab From 9b4e27b52853c5da77e61a4e36fbc40688b7a829 Mon Sep 17 00:00:00 2001 From: Robert Richter Date: Fri, 22 Aug 2008 20:23:37 +0200 Subject: [PATCH 731/750] x86: fix: do not run code in amd_bus.c on non-AMD CPUs Jan Beulich wrote: > Even worse - this would even try to access the MSR on non-AMD CPUs > (currently probably prevented just by the fact that only AMD ones use > family values of 0x10 or higher). This patch adds cpu vendor check to the postcore_initcalls. Reported-by: Jan Beulich Signed-off-by: Robert Richter Signed-off-by: Ingo Molnar --- arch/x86/pci/amd_bus.c | 19 ++++++++++++++++--- 1 file changed, 16 insertions(+), 3 deletions(-) diff --git a/arch/x86/pci/amd_bus.c b/arch/x86/pci/amd_bus.c index dbf53236971..4a6f1a6a3aa 100644 --- a/arch/x86/pci/amd_bus.c +++ b/arch/x86/pci/amd_bus.c @@ -555,9 +555,11 @@ static int __init early_fill_mp_bus_info(void) return 0; } -postcore_initcall(early_fill_mp_bus_info); +#else /* !CONFIG_X86_64 */ -#endif +static int __init early_fill_mp_bus_info(void) { return 0; } + +#endif /* !CONFIG_X86_64 */ /* common 32/64 bit code */ @@ -583,4 +585,15 @@ static int __init enable_pci_io_ecs(void) return 0; } -postcore_initcall(enable_pci_io_ecs); +static int __init amd_postcore_init(void) +{ + if (boot_cpu_data.x86_vendor != X86_VENDOR_AMD) + return 0; + + early_fill_mp_bus_info(); + enable_pci_io_ecs(); + + return 0; +} + +postcore_initcall(amd_postcore_init); -- GitLab From 91ede005d72df60d6b3f252be177a4743a6aa46a Mon Sep 17 00:00:00 2001 From: Robert Richter Date: Fri, 22 Aug 2008 20:23:38 +0200 Subject: [PATCH 732/750] x86: fix: make PCI ECS for AMD CPUs hotplug capable Until now, PCI ECS setup was performed at boot time only and for cpus that are enabled then. This patch fixes this and adds cpu hotplug. Tests sequence (check if ECS bit is set when bringing cpu online again): # ( perl -e 'sysseek(STDIN, 0xC001001F, 0)'; hexdump -n 8 -e '2/4 "%08x " "\n"' ) < /dev/cpu/1/msr 00000008 00404010 # ( perl -e 'sysseek(STDOUT, 0xC001001F, 0); print pack "l*", 8, 0x00400010' ) > /dev/cpu/1/msr # ( perl -e 'sysseek(STDIN, 0xC001001F, 0)'; hexdump -n 8 -e '2/4 "%08x " "\n"' ) < /dev/cpu/1/msr 00000008 00400010 # echo 0 > /sys/devices/system/cpu/cpu1/online # echo 1 > /sys/devices/system/cpu/cpu1/online # ( perl -e 'sysseek(STDIN, 0xC001001F, 0)'; hexdump -n 8 -e '2/4 "%08x " "\n"' ) < /dev/cpu/1/msr 00000008 00404010 Reported-by: Yinghai Lu Signed-off-by: Robert Richter Signed-off-by: Ingo Molnar --- arch/x86/pci/amd_bus.c | 35 +++++++++++++++++++++++++++++++---- 1 file changed, 31 insertions(+), 4 deletions(-) diff --git a/arch/x86/pci/amd_bus.c b/arch/x86/pci/amd_bus.c index 4a6f1a6a3aa..6a0fca78c36 100644 --- a/arch/x86/pci/amd_bus.c +++ b/arch/x86/pci/amd_bus.c @@ -1,6 +1,7 @@ #include #include #include +#include #include "pci.h" #ifdef CONFIG_X86_64 @@ -565,7 +566,7 @@ static int __init early_fill_mp_bus_info(void) { return 0; } #define ENABLE_CF8_EXT_CFG (1ULL << 46) -static void enable_pci_io_ecs_per_cpu(void *unused) +static void enable_pci_io_ecs(void *unused) { u64 reg; rdmsrl(MSR_AMD64_NB_CFG, reg); @@ -575,13 +576,39 @@ static void enable_pci_io_ecs_per_cpu(void *unused) } } -static int __init enable_pci_io_ecs(void) +static int __cpuinit amd_cpu_notify(struct notifier_block *self, + unsigned long action, void *hcpu) { + int cpu = (long)hcpu; + switch(action) { + case CPU_ONLINE: + case CPU_ONLINE_FROZEN: + smp_call_function_single(cpu, enable_pci_io_ecs, NULL, 0); + break; + default: + break; + } + return NOTIFY_OK; +} + +static struct notifier_block __cpuinitdata amd_cpu_notifier = { + .notifier_call = amd_cpu_notify, +}; + +static int __init pci_io_ecs_init(void) +{ + int cpu; + /* assume all cpus from fam10h have IO ECS */ if (boot_cpu_data.x86 < 0x10) return 0; - on_each_cpu(enable_pci_io_ecs_per_cpu, NULL, 1); + + register_cpu_notifier(&amd_cpu_notifier); + for_each_online_cpu(cpu) + amd_cpu_notify(&amd_cpu_notifier, (unsigned long)CPU_ONLINE, + (void *)(long)cpu); pci_probe |= PCI_HAS_IO_ECS; + return 0; } @@ -591,7 +618,7 @@ static int __init amd_postcore_init(void) return 0; early_fill_mp_bus_info(); - enable_pci_io_ecs(); + pci_io_ecs_init(); return 0; } -- GitLab From 8735728ef8dc935c4fb351f913758fdbb62c308d Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Fri, 22 Aug 2008 22:23:09 +0200 Subject: [PATCH 733/750] x86 MCE: Fix CPU hotplug problem with multiple multicore AMD CPUs During CPU hot-remove the sysfs directory created by threshold_create_bank(), defined in arch/x86/kernel/cpu/mcheck/mce_amd_64.c, has to be removed before its parent directory, created by mce_create_device(), defined in arch/x86/kernel/cpu/mcheck/mce_64.c . Moreover, when the CPU in question is hotplugged again, obviously the latter has to be created before the former. At present, the right ordering is not enforced, because all of these operations are carried out by CPU hotplug notifiers which are not appropriately ordered with respect to each other. This leads to serious problems on systems with two or more multicore AMD CPUs, among other things during suspend and hibernation. Fix the problem by placing threshold bank CPU hotplug callbacks in mce_cpu_callback(), so that they are invoked at the right places, if defined. Additionally, use kobject_del() to remove the sysfs directory associated with the kobject created by kobject_create_and_add() in threshold_create_bank(), to prevent the kernel from crashing during CPU hotplug operations on systems with two or more multicore AMD CPUs. This patch fixes bug #11337. Signed-off-by: Rafael J. Wysocki Acked-by: Andi Kleen Tested-by: Mark Langsdorf Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/mcheck/mce_64.c | 5 +++++ arch/x86/kernel/cpu/mcheck/mce_amd_64.c | 18 +++++------------- include/asm-x86/mce.h | 1 + 3 files changed, 11 insertions(+), 13 deletions(-) diff --git a/arch/x86/kernel/cpu/mcheck/mce_64.c b/arch/x86/kernel/cpu/mcheck/mce_64.c index 65a339678ec..726a5fcdf34 100644 --- a/arch/x86/kernel/cpu/mcheck/mce_64.c +++ b/arch/x86/kernel/cpu/mcheck/mce_64.c @@ -759,6 +759,7 @@ static struct sysdev_class mce_sysclass = { }; DEFINE_PER_CPU(struct sys_device, device_mce); +void (*threshold_cpu_callback)(unsigned long action, unsigned int cpu) __cpuinitdata; /* Why are there no generic functions for this? */ #define ACCESSOR(name, var, start) \ @@ -883,9 +884,13 @@ static int __cpuinit mce_cpu_callback(struct notifier_block *nfb, case CPU_ONLINE: case CPU_ONLINE_FROZEN: mce_create_device(cpu); + if (threshold_cpu_callback) + threshold_cpu_callback(action, cpu); break; case CPU_DEAD: case CPU_DEAD_FROZEN: + if (threshold_cpu_callback) + threshold_cpu_callback(action, cpu); mce_remove_device(cpu); break; } diff --git a/arch/x86/kernel/cpu/mcheck/mce_amd_64.c b/arch/x86/kernel/cpu/mcheck/mce_amd_64.c index 88736cadbaa..5eb390a4b2e 100644 --- a/arch/x86/kernel/cpu/mcheck/mce_amd_64.c +++ b/arch/x86/kernel/cpu/mcheck/mce_amd_64.c @@ -628,6 +628,7 @@ static void threshold_remove_bank(unsigned int cpu, int bank) deallocate_threshold_block(cpu, bank); free_out: + kobject_del(b->kobj); kobject_put(b->kobj); kfree(b); per_cpu(threshold_banks, cpu)[bank] = NULL; @@ -645,14 +646,11 @@ static void threshold_remove_device(unsigned int cpu) } /* get notified when a cpu comes on/off */ -static int __cpuinit threshold_cpu_callback(struct notifier_block *nfb, - unsigned long action, void *hcpu) +static void __cpuinit amd_64_threshold_cpu_callback(unsigned long action, + unsigned int cpu) { - /* cpu was unsigned int to begin with */ - unsigned int cpu = (unsigned long)hcpu; - if (cpu >= NR_CPUS) - goto out; + return; switch (action) { case CPU_ONLINE: @@ -666,14 +664,8 @@ static int __cpuinit threshold_cpu_callback(struct notifier_block *nfb, default: break; } - out: - return NOTIFY_OK; } -static struct notifier_block threshold_cpu_notifier __cpuinitdata = { - .notifier_call = threshold_cpu_callback, -}; - static __init int threshold_init_device(void) { unsigned lcpu = 0; @@ -684,7 +676,7 @@ static __init int threshold_init_device(void) if (err) return err; } - register_hotcpu_notifier(&threshold_cpu_notifier); + threshold_cpu_callback = amd_64_threshold_cpu_callback; return 0; } diff --git a/include/asm-x86/mce.h b/include/asm-x86/mce.h index 94f1fd79e22..531eaa58745 100644 --- a/include/asm-x86/mce.h +++ b/include/asm-x86/mce.h @@ -92,6 +92,7 @@ extern int mce_disabled; void mce_log(struct mce *m); DECLARE_PER_CPU(struct sys_device, device_mce); +extern void (*threshold_cpu_callback)(unsigned long action, unsigned int cpu); #ifdef CONFIG_X86_MCE_INTEL void mce_intel_feature_init(struct cpuinfo_x86 *c); -- GitLab From 7a8fc9b248e77a4eab0613acf30a6811799786b3 Mon Sep 17 00:00:00 2001 From: Adrian Bunk Date: Sun, 17 Aug 2008 17:36:59 +0300 Subject: [PATCH 734/750] removed unused #include 's This patch lets the files using linux/version.h match the files that #include it. Signed-off-by: Adrian Bunk Signed-off-by: Linus Torvalds --- arch/arm/plat-omap/clock.c | 1 - arch/cris/arch-v32/kernel/fasttimer.c | 2 -- arch/mn10300/kernel/mn10300-serial.c | 1 - arch/powerpc/sysdev/bestcomm/gen_bd.c | 1 - arch/x86/mach-rdc321x/platform.c | 1 - drivers/atm/adummy.c | 1 - drivers/char/xilinx_hwicap/buffer_icap.h | 1 - drivers/char/xilinx_hwicap/fifo_icap.h | 1 - drivers/char/xilinx_hwicap/xilinx_hwicap.h | 1 - drivers/edac/edac_core.h | 1 - drivers/i2c/busses/i2c-at91.c | 1 - drivers/infiniband/hw/ehca/ehca_tools.h | 1 - drivers/infiniband/hw/ipath/ipath_fs.c | 1 - drivers/infiniband/hw/nes/nes.h | 1 - drivers/infiniband/ulp/iser/iser_verbs.c | 1 - drivers/input/keyboard/bf54x-keys.c | 1 - drivers/input/touchscreen/mainstone-wm97xx.c | 1 - drivers/mfd/asic3.c | 1 - drivers/misc/eeprom_93cx6.c | 1 - drivers/mtd/maps/amd76xrom.c | 1 - drivers/mtd/maps/ck804xrom.c | 1 - drivers/mtd/maps/esb2rom.c | 1 - drivers/mtd/nand/au1550nd.c | 1 - drivers/net/myri10ge/myri10ge.c | 1 - drivers/net/netxen/netxen_nic.h | 1 - drivers/net/netxen/netxen_nic_ethtool.c | 1 - drivers/net/netxen/netxen_nic_hdr.h | 2 -- drivers/net/tokenring/lanstreamer.c | 1 - drivers/net/tokenring/lanstreamer.h | 2 -- drivers/net/wireless/b43legacy/main.c | 1 - drivers/net/wireless/iwlwifi/iwl-3945-led.c | 1 - drivers/net/wireless/iwlwifi/iwl-led.c | 1 - drivers/net/wireless/iwlwifi/iwl-rfkill.c | 1 - drivers/rtc/rtc-max6902.c | 2 -- drivers/rtc/rtc-r9701.c | 1 - drivers/s390/net/ctcm_mpc.c | 1 - drivers/scsi/dpt/dpti_i2o.h | 1 - drivers/scsi/ips.c | 1 - drivers/scsi/ips.h | 1 - drivers/scsi/lpfc/lpfc_debugfs.c | 1 - drivers/scsi/nsp32.c | 1 - drivers/scsi/nsp32.h | 1 - drivers/scsi/pcmcia/nsp_cs.c | 1 - drivers/scsi/qla2xxx/qla_mid.c | 1 - drivers/usb/atm/ueagle-atm.c | 1 - drivers/usb/gadget/amd5536udc.c | 1 - drivers/usb/gadget/s3c2410_udc.c | 1 - drivers/usb/misc/iowarrior.c | 1 - drivers/usb/serial/garmin_gps.c | 2 -- drivers/video/arkfb.c | 1 - drivers/video/s3fb.c | 1 - drivers/video/vermilion/vermilion.h | 1 - drivers/video/vt8623fb.c | 1 - drivers/video/xilinxfb.c | 1 - fs/jffs2/jffs2_fs_i.h | 1 - fs/xfs/xfs_dmapi.h | 1 - include/asm-x86/xen/hypervisor.h | 1 - include/linux/fs_uart_pd.h | 1 - kernel/nsproxy.c | 1 - kernel/power/swap.c | 1 - kernel/user_namespace.c | 1 - kernel/utsname.c | 1 - kernel/utsname_sysctl.c | 1 - sound/mips/au1x00.c | 1 - sound/soc/at91/eti_b1_wm8731.c | 1 - sound/soc/codecs/wm8753.c | 1 - sound/soc/codecs/wm9712.c | 1 - 67 files changed, 72 deletions(-) diff --git a/arch/arm/plat-omap/clock.c b/arch/arm/plat-omap/clock.c index 23a07059999..197974defbe 100644 --- a/arch/arm/plat-omap/clock.c +++ b/arch/arm/plat-omap/clock.c @@ -10,7 +10,6 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ -#include #include #include #include diff --git a/arch/cris/arch-v32/kernel/fasttimer.c b/arch/cris/arch-v32/kernel/fasttimer.c index 2de9d5849ef..111caa1a2ef 100644 --- a/arch/cris/arch-v32/kernel/fasttimer.c +++ b/arch/cris/arch-v32/kernel/fasttimer.c @@ -19,8 +19,6 @@ #include #include -#include - #include #include #include diff --git a/arch/mn10300/kernel/mn10300-serial.c b/arch/mn10300/kernel/mn10300-serial.c index 8b054e7a8ae..aa07d0cd190 100644 --- a/arch/mn10300/kernel/mn10300-serial.c +++ b/arch/mn10300/kernel/mn10300-serial.c @@ -17,7 +17,6 @@ static const char serial_revdate[] = "2007-11-06"; #define SUPPORT_SYSRQ #endif -#include #include #include #include diff --git a/arch/powerpc/sysdev/bestcomm/gen_bd.c b/arch/powerpc/sysdev/bestcomm/gen_bd.c index a3a134c35b0..e0a53e3147b 100644 --- a/arch/powerpc/sysdev/bestcomm/gen_bd.c +++ b/arch/powerpc/sysdev/bestcomm/gen_bd.c @@ -11,7 +11,6 @@ * */ -#include #include #include #include diff --git a/arch/x86/mach-rdc321x/platform.c b/arch/x86/mach-rdc321x/platform.c index a037041817c..4f4e50c3ad3 100644 --- a/arch/x86/mach-rdc321x/platform.c +++ b/arch/x86/mach-rdc321x/platform.c @@ -25,7 +25,6 @@ #include #include #include -#include #include #include diff --git a/drivers/atm/adummy.c b/drivers/atm/adummy.c index 2ebd07f2ef8..5effec6f545 100644 --- a/drivers/atm/adummy.c +++ b/drivers/atm/adummy.c @@ -3,7 +3,6 @@ */ #include -#include #include #include #include diff --git a/drivers/char/xilinx_hwicap/buffer_icap.h b/drivers/char/xilinx_hwicap/buffer_icap.h index c5b1840906b..8b0252bf06e 100644 --- a/drivers/char/xilinx_hwicap/buffer_icap.h +++ b/drivers/char/xilinx_hwicap/buffer_icap.h @@ -38,7 +38,6 @@ #include #include -#include #include #include diff --git a/drivers/char/xilinx_hwicap/fifo_icap.h b/drivers/char/xilinx_hwicap/fifo_icap.h index ffabd3ba2bd..62bda453c90 100644 --- a/drivers/char/xilinx_hwicap/fifo_icap.h +++ b/drivers/char/xilinx_hwicap/fifo_icap.h @@ -38,7 +38,6 @@ #include #include -#include #include #include diff --git a/drivers/char/xilinx_hwicap/xilinx_hwicap.h b/drivers/char/xilinx_hwicap/xilinx_hwicap.h index 1f9c8b082db..24d0d9b938f 100644 --- a/drivers/char/xilinx_hwicap/xilinx_hwicap.h +++ b/drivers/char/xilinx_hwicap/xilinx_hwicap.h @@ -38,7 +38,6 @@ #include #include -#include #include #include diff --git a/drivers/edac/edac_core.h b/drivers/edac/edac_core.h index b27b13c5eb5..4b55ec607a8 100644 --- a/drivers/edac/edac_core.h +++ b/drivers/edac/edac_core.h @@ -34,7 +34,6 @@ #include #include #include -#include #define EDAC_MC_LABEL_LEN 31 #define EDAC_DEVICE_NAME_LEN 31 diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c index c1adcdbf797..9efb0213725 100644 --- a/drivers/i2c/busses/i2c-at91.c +++ b/drivers/i2c/busses/i2c-at91.c @@ -14,7 +14,6 @@ */ #include -#include #include #include #include diff --git a/drivers/infiniband/hw/ehca/ehca_tools.h b/drivers/infiniband/hw/ehca/ehca_tools.h index ec950bf8c47..21f7d06f14a 100644 --- a/drivers/infiniband/hw/ehca/ehca_tools.h +++ b/drivers/infiniband/hw/ehca/ehca_tools.h @@ -54,7 +54,6 @@ #include #include #include -#include #include #include #include diff --git a/drivers/infiniband/hw/ipath/ipath_fs.c b/drivers/infiniband/hw/ipath/ipath_fs.c index 23faba9d21e..8bb5170b4e4 100644 --- a/drivers/infiniband/hw/ipath/ipath_fs.c +++ b/drivers/infiniband/hw/ipath/ipath_fs.c @@ -31,7 +31,6 @@ * SOFTWARE. */ -#include #include #include #include diff --git a/drivers/infiniband/hw/nes/nes.h b/drivers/infiniband/hw/nes/nes.h index 39bd897b40c..8eb7ae96974 100644 --- a/drivers/infiniband/hw/nes/nes.h +++ b/drivers/infiniband/hw/nes/nes.h @@ -43,7 +43,6 @@ #include #include #include -#include #include #include diff --git a/drivers/infiniband/ulp/iser/iser_verbs.c b/drivers/infiniband/ulp/iser/iser_verbs.c index 63462ecca14..26ff6214a81 100644 --- a/drivers/infiniband/ulp/iser/iser_verbs.c +++ b/drivers/infiniband/ulp/iser/iser_verbs.c @@ -33,7 +33,6 @@ #include #include #include -#include #include "iscsi_iser.h" diff --git a/drivers/input/keyboard/bf54x-keys.c b/drivers/input/keyboard/bf54x-keys.c index 54ed8e2e1c0..6f227d3dbda 100644 --- a/drivers/input/keyboard/bf54x-keys.c +++ b/drivers/input/keyboard/bf54x-keys.c @@ -29,7 +29,6 @@ */ #include -#include #include #include diff --git a/drivers/input/touchscreen/mainstone-wm97xx.c b/drivers/input/touchscreen/mainstone-wm97xx.c index 283f93a0cee..37a555f3730 100644 --- a/drivers/input/touchscreen/mainstone-wm97xx.c +++ b/drivers/input/touchscreen/mainstone-wm97xx.c @@ -25,7 +25,6 @@ #include #include -#include #include #include #include diff --git a/drivers/mfd/asic3.c b/drivers/mfd/asic3.c index c6408a62d95..bc2a807f210 100644 --- a/drivers/mfd/asic3.c +++ b/drivers/mfd/asic3.c @@ -16,7 +16,6 @@ * */ -#include #include #include #include diff --git a/drivers/misc/eeprom_93cx6.c b/drivers/misc/eeprom_93cx6.c index ea55654e594..15b1780025c 100644 --- a/drivers/misc/eeprom_93cx6.c +++ b/drivers/misc/eeprom_93cx6.c @@ -26,7 +26,6 @@ #include #include -#include #include #include diff --git a/drivers/mtd/maps/amd76xrom.c b/drivers/mtd/maps/amd76xrom.c index 948b86f35ef..d1eec7d3243 100644 --- a/drivers/mtd/maps/amd76xrom.c +++ b/drivers/mtd/maps/amd76xrom.c @@ -6,7 +6,6 @@ #include #include -#include #include #include #include diff --git a/drivers/mtd/maps/ck804xrom.c b/drivers/mtd/maps/ck804xrom.c index effaf7cdefa..1a6feb4474d 100644 --- a/drivers/mtd/maps/ck804xrom.c +++ b/drivers/mtd/maps/ck804xrom.c @@ -9,7 +9,6 @@ #include #include -#include #include #include #include diff --git a/drivers/mtd/maps/esb2rom.c b/drivers/mtd/maps/esb2rom.c index aa64a475278..bbbcdd4c8d1 100644 --- a/drivers/mtd/maps/esb2rom.c +++ b/drivers/mtd/maps/esb2rom.c @@ -12,7 +12,6 @@ #include #include -#include #include #include #include diff --git a/drivers/mtd/nand/au1550nd.c b/drivers/mtd/nand/au1550nd.c index 761946ea45b..92c334ff450 100644 --- a/drivers/mtd/nand/au1550nd.c +++ b/drivers/mtd/nand/au1550nd.c @@ -16,7 +16,6 @@ #include #include #include -#include #include #include diff --git a/drivers/net/myri10ge/myri10ge.c b/drivers/net/myri10ge/myri10ge.c index 5d76cd09e24..54cd89cb083 100644 --- a/drivers/net/myri10ge/myri10ge.c +++ b/drivers/net/myri10ge/myri10ge.c @@ -56,7 +56,6 @@ #include #include #include -#include #include #include #include diff --git a/drivers/net/netxen/netxen_nic.h b/drivers/net/netxen/netxen_nic.h index ab871df6b1d..244ab49c433 100644 --- a/drivers/net/netxen/netxen_nic.h +++ b/drivers/net/netxen/netxen_nic.h @@ -45,7 +45,6 @@ #include #include #include -#include #include #include diff --git a/drivers/net/netxen/netxen_nic_ethtool.c b/drivers/net/netxen/netxen_nic_ethtool.c index 4ad3e0844b9..b974ca0fc53 100644 --- a/drivers/net/netxen/netxen_nic_ethtool.c +++ b/drivers/net/netxen/netxen_nic_ethtool.c @@ -38,7 +38,6 @@ #include #include #include -#include #include "netxen_nic.h" #include "netxen_nic_hw.h" diff --git a/drivers/net/netxen/netxen_nic_hdr.h b/drivers/net/netxen/netxen_nic_hdr.h index e8e8d73f6ed..e80f9e3e597 100644 --- a/drivers/net/netxen/netxen_nic_hdr.h +++ b/drivers/net/netxen/netxen_nic_hdr.h @@ -32,8 +32,6 @@ #include #include -#include - #include #include #include diff --git a/drivers/net/tokenring/lanstreamer.c b/drivers/net/tokenring/lanstreamer.c index 47d84cd2809..59d1673f938 100644 --- a/drivers/net/tokenring/lanstreamer.c +++ b/drivers/net/tokenring/lanstreamer.c @@ -119,7 +119,6 @@ #include #include #include -#include #include #include diff --git a/drivers/net/tokenring/lanstreamer.h b/drivers/net/tokenring/lanstreamer.h index e7bb3494afc..13ccee6449c 100644 --- a/drivers/net/tokenring/lanstreamer.h +++ b/drivers/net/tokenring/lanstreamer.h @@ -60,8 +60,6 @@ * */ -#include - /* MAX_INTR - the maximum number of times we can loop * inside the interrupt function before returning * control to the OS (maximum value is 256) diff --git a/drivers/net/wireless/b43legacy/main.c b/drivers/net/wireless/b43legacy/main.c index 2541c81932f..1cb77db5c29 100644 --- a/drivers/net/wireless/b43legacy/main.c +++ b/drivers/net/wireless/b43legacy/main.c @@ -34,7 +34,6 @@ #include #include #include -#include #include #include #include diff --git a/drivers/net/wireless/iwlwifi/iwl-3945-led.c b/drivers/net/wireless/iwlwifi/iwl-3945-led.c index d3336966b6b..705c65bed9f 100644 --- a/drivers/net/wireless/iwlwifi/iwl-3945-led.c +++ b/drivers/net/wireless/iwlwifi/iwl-3945-led.c @@ -27,7 +27,6 @@ #include #include -#include #include #include #include diff --git a/drivers/net/wireless/iwlwifi/iwl-led.c b/drivers/net/wireless/iwlwifi/iwl-led.c index cb11c4a4d69..4eee1b163cd 100644 --- a/drivers/net/wireless/iwlwifi/iwl-led.c +++ b/drivers/net/wireless/iwlwifi/iwl-led.c @@ -27,7 +27,6 @@ #include #include -#include #include #include #include diff --git a/drivers/net/wireless/iwlwifi/iwl-rfkill.c b/drivers/net/wireless/iwlwifi/iwl-rfkill.c index e5e5846e9f2..5d642298f04 100644 --- a/drivers/net/wireless/iwlwifi/iwl-rfkill.c +++ b/drivers/net/wireless/iwlwifi/iwl-rfkill.c @@ -27,7 +27,6 @@ *****************************************************************************/ #include #include -#include #include #include diff --git a/drivers/rtc/rtc-max6902.c b/drivers/rtc/rtc-max6902.c index 12f0310ae89..78b2551fb19 100644 --- a/drivers/rtc/rtc-max6902.c +++ b/drivers/rtc/rtc-max6902.c @@ -20,8 +20,6 @@ */ #include -#include - #include #include #include diff --git a/drivers/rtc/rtc-r9701.c b/drivers/rtc/rtc-r9701.c index b35f9bfa2af..395985b339c 100644 --- a/drivers/rtc/rtc-r9701.c +++ b/drivers/rtc/rtc-r9701.c @@ -14,7 +14,6 @@ */ #include -#include #include #include #include diff --git a/drivers/s390/net/ctcm_mpc.c b/drivers/s390/net/ctcm_mpc.c index 49ae1cd25ca..2de1e2fccbf 100644 --- a/drivers/s390/net/ctcm_mpc.c +++ b/drivers/s390/net/ctcm_mpc.c @@ -19,7 +19,6 @@ #undef DEBUGDATA #undef DEBUGCCW -#include #include #include #include diff --git a/drivers/scsi/dpt/dpti_i2o.h b/drivers/scsi/dpt/dpti_i2o.h index 19406cea6d6..179ad77f6cc 100644 --- a/drivers/scsi/dpt/dpti_i2o.h +++ b/drivers/scsi/dpt/dpti_i2o.h @@ -21,7 +21,6 @@ #include -#include #include #include diff --git a/drivers/scsi/ips.c b/drivers/scsi/ips.c index 7c615c70ec5..bc9e6ddf41d 100644 --- a/drivers/scsi/ips.c +++ b/drivers/scsi/ips.c @@ -165,7 +165,6 @@ #include #include #include -#include #include #include #include diff --git a/drivers/scsi/ips.h b/drivers/scsi/ips.h index e0657b6f009..4e49fbcfe8a 100644 --- a/drivers/scsi/ips.h +++ b/drivers/scsi/ips.h @@ -50,7 +50,6 @@ #ifndef _IPS_H_ #define _IPS_H_ -#include #include #include #include diff --git a/drivers/scsi/lpfc/lpfc_debugfs.c b/drivers/scsi/lpfc/lpfc_debugfs.c index 90272e65957..094b47e94b2 100644 --- a/drivers/scsi/lpfc/lpfc_debugfs.c +++ b/drivers/scsi/lpfc/lpfc_debugfs.c @@ -27,7 +27,6 @@ #include #include #include -#include #include #include diff --git a/drivers/scsi/nsp32.c b/drivers/scsi/nsp32.c index edf9fdb3cb3..22052bb7bec 100644 --- a/drivers/scsi/nsp32.c +++ b/drivers/scsi/nsp32.c @@ -23,7 +23,6 @@ * 1.2: PowerPC (big endian) support. */ -#include #include #include #include diff --git a/drivers/scsi/nsp32.h b/drivers/scsi/nsp32.h index 6715ecb3bfc..9565acf1aa7 100644 --- a/drivers/scsi/nsp32.h +++ b/drivers/scsi/nsp32.h @@ -16,7 +16,6 @@ #ifndef _NSP32_H #define _NSP32_H -#include //#define NSP32_DEBUG 9 /* diff --git a/drivers/scsi/pcmcia/nsp_cs.c b/drivers/scsi/pcmcia/nsp_cs.c index a221b6ef9fa..24e6cb8396e 100644 --- a/drivers/scsi/pcmcia/nsp_cs.c +++ b/drivers/scsi/pcmcia/nsp_cs.c @@ -25,7 +25,6 @@ ***********************************************************************/ -#include #include #include #include diff --git a/drivers/scsi/qla2xxx/qla_mid.c b/drivers/scsi/qla2xxx/qla_mid.c index 50baf6a1d67..93560cd7278 100644 --- a/drivers/scsi/qla2xxx/qla_mid.c +++ b/drivers/scsi/qla2xxx/qla_mid.c @@ -6,7 +6,6 @@ */ #include "qla_def.h" -#include #include #include #include diff --git a/drivers/usb/atm/ueagle-atm.c b/drivers/usb/atm/ueagle-atm.c index cb01b5106ef..b6483dd98ac 100644 --- a/drivers/usb/atm/ueagle-atm.c +++ b/drivers/usb/atm/ueagle-atm.c @@ -64,7 +64,6 @@ #include #include #include -#include #include #include diff --git a/drivers/usb/gadget/amd5536udc.c b/drivers/usb/gadget/amd5536udc.c index 1500e1b3c30..abf8192f89e 100644 --- a/drivers/usb/gadget/amd5536udc.c +++ b/drivers/usb/gadget/amd5536udc.c @@ -44,7 +44,6 @@ #include #include #include -#include #include #include #include diff --git a/drivers/usb/gadget/s3c2410_udc.c b/drivers/usb/gadget/s3c2410_udc.c index 53880738459..29d13ebe750 100644 --- a/drivers/usb/gadget/s3c2410_udc.c +++ b/drivers/usb/gadget/s3c2410_udc.c @@ -35,7 +35,6 @@ #include #include #include -#include #include #include diff --git a/drivers/usb/misc/iowarrior.c b/drivers/usb/misc/iowarrior.c index e6ca9979e3a..a4ef77ef917 100644 --- a/drivers/usb/misc/iowarrior.c +++ b/drivers/usb/misc/iowarrior.c @@ -19,7 +19,6 @@ #include #include #include -#include #include /* Version Information */ diff --git a/drivers/usb/serial/garmin_gps.c b/drivers/usb/serial/garmin_gps.c index 2e663f1afd5..d9538208807 100644 --- a/drivers/usb/serial/garmin_gps.c +++ b/drivers/usb/serial/garmin_gps.c @@ -38,8 +38,6 @@ #include #include -#include - /* the mode to be set when the port ist opened */ static int initial_mode = 1; diff --git a/drivers/video/arkfb.c b/drivers/video/arkfb.c index 4bd569e479a..314d18694b6 100644 --- a/drivers/video/arkfb.c +++ b/drivers/video/arkfb.c @@ -11,7 +11,6 @@ * Code is based on s3fb */ -#include #include #include #include diff --git a/drivers/video/s3fb.c b/drivers/video/s3fb.c index 8361bd0e3df..4dcec48a1d7 100644 --- a/drivers/video/s3fb.c +++ b/drivers/video/s3fb.c @@ -11,7 +11,6 @@ * which is based on the code of neofb. */ -#include #include #include #include diff --git a/drivers/video/vermilion/vermilion.h b/drivers/video/vermilion/vermilion.h index c4aba59d480..7491abfcf1f 100644 --- a/drivers/video/vermilion/vermilion.h +++ b/drivers/video/vermilion/vermilion.h @@ -30,7 +30,6 @@ #define _VERMILION_H_ #include -#include #include #include #include diff --git a/drivers/video/vt8623fb.c b/drivers/video/vt8623fb.c index 34aae7a2a62..3df17dc8c3d 100644 --- a/drivers/video/vt8623fb.c +++ b/drivers/video/vt8623fb.c @@ -12,7 +12,6 @@ * (http://davesdomain.org.uk/viafb/) */ -#include #include #include #include diff --git a/drivers/video/xilinxfb.c b/drivers/video/xilinxfb.c index 7b3a8423f48..5da3d2423cc 100644 --- a/drivers/video/xilinxfb.c +++ b/drivers/video/xilinxfb.c @@ -24,7 +24,6 @@ #include #include #include -#include #include #include #include diff --git a/fs/jffs2/jffs2_fs_i.h b/fs/jffs2/jffs2_fs_i.h index 31559f45fdd..4c41db91eaa 100644 --- a/fs/jffs2/jffs2_fs_i.h +++ b/fs/jffs2/jffs2_fs_i.h @@ -12,7 +12,6 @@ #ifndef _JFFS2_FS_I #define _JFFS2_FS_I -#include #include #include #include diff --git a/fs/xfs/xfs_dmapi.h b/fs/xfs/xfs_dmapi.h index cdc2d3464a1..2813cdd7237 100644 --- a/fs/xfs/xfs_dmapi.h +++ b/fs/xfs/xfs_dmapi.h @@ -18,7 +18,6 @@ #ifndef __XFS_DMAPI_H__ #define __XFS_DMAPI_H__ -#include /* Values used to define the on-disk version of dm_attrname_t. All * on-disk attribute names start with the 8-byte string "SGI_DMI_". * diff --git a/include/asm-x86/xen/hypervisor.h b/include/asm-x86/xen/hypervisor.h index 8e15dd28c91..04ee0610014 100644 --- a/include/asm-x86/xen/hypervisor.h +++ b/include/asm-x86/xen/hypervisor.h @@ -35,7 +35,6 @@ #include #include -#include #include #include diff --git a/include/linux/fs_uart_pd.h b/include/linux/fs_uart_pd.h index 809bb9ffc78..36b61ff3927 100644 --- a/include/linux/fs_uart_pd.h +++ b/include/linux/fs_uart_pd.h @@ -12,7 +12,6 @@ #ifndef FS_UART_PD_H #define FS_UART_PD_H -#include #include enum fs_uart_id { diff --git a/kernel/nsproxy.c b/kernel/nsproxy.c index 21575fc46d0..1d3ef29a258 100644 --- a/kernel/nsproxy.c +++ b/kernel/nsproxy.c @@ -14,7 +14,6 @@ */ #include -#include #include #include #include diff --git a/kernel/power/swap.c b/kernel/power/swap.c index a0abf9a463f..80ccac849e4 100644 --- a/kernel/power/swap.c +++ b/kernel/power/swap.c @@ -14,7 +14,6 @@ #include #include #include -#include #include #include #include diff --git a/kernel/user_namespace.c b/kernel/user_namespace.c index a9ab0596de4..532858fa5b8 100644 --- a/kernel/user_namespace.c +++ b/kernel/user_namespace.c @@ -6,7 +6,6 @@ */ #include -#include #include #include #include diff --git a/kernel/utsname.c b/kernel/utsname.c index 64d398f1244..815237a55af 100644 --- a/kernel/utsname.c +++ b/kernel/utsname.c @@ -12,7 +12,6 @@ #include #include #include -#include #include #include diff --git a/kernel/utsname_sysctl.c b/kernel/utsname_sysctl.c index fe3a56c2256..4ab9659d269 100644 --- a/kernel/utsname_sysctl.c +++ b/kernel/utsname_sysctl.c @@ -12,7 +12,6 @@ #include #include #include -#include #include static void *get_uts(ctl_table *table, int write) diff --git a/sound/mips/au1x00.c b/sound/mips/au1x00.c index ee0741f9eb5..fbef38a9604 100644 --- a/sound/mips/au1x00.c +++ b/sound/mips/au1x00.c @@ -38,7 +38,6 @@ #include #include #include -#include #include #include #include diff --git a/sound/soc/at91/eti_b1_wm8731.c b/sound/soc/at91/eti_b1_wm8731.c index b081e83766b..b81d6b2cfa1 100644 --- a/sound/soc/at91/eti_b1_wm8731.c +++ b/sound/soc/at91/eti_b1_wm8731.c @@ -22,7 +22,6 @@ #include #include -#include #include #include #include diff --git a/sound/soc/codecs/wm8753.c b/sound/soc/codecs/wm8753.c index 8604809f0c3..dc7b18fd278 100644 --- a/sound/soc/codecs/wm8753.c +++ b/sound/soc/codecs/wm8753.c @@ -34,7 +34,6 @@ #include #include -#include #include #include #include diff --git a/sound/soc/codecs/wm9712.c b/sound/soc/codecs/wm9712.c index 1fb7f9a7aec..2f1c91b1d55 100644 --- a/sound/soc/codecs/wm9712.c +++ b/sound/soc/codecs/wm9712.c @@ -13,7 +13,6 @@ #include #include -#include #include #include #include -- GitLab From 83097aca8567a0bd593534853b71fe0fa9a75d69 Mon Sep 17 00:00:00 2001 From: Arjan van de Ven Date: Sat, 23 Aug 2008 21:45:21 -0700 Subject: [PATCH 735/750] Fix oops in acer_wmi driver (acer_wmi_init) The acer_wmi driver does a DMI scan for quirks, and then sets flags into the "interface" datastructure for some cases. However, the quirks happen real early before "interface" is per se initialized from NULL. The patch below 1) adds a NULL pointer check and 2) (re)runs the quirks at the end, when "interface" has it's final value. Reported-by: kerneloops.org Acked-by: Carlos Corbacho CC: stable@vger.kernel.org Signed-off-by: Arjan van de Ven Signed-off-by: Linus Torvalds --- drivers/misc/acer-wmi.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/misc/acer-wmi.c b/drivers/misc/acer-wmi.c index b2d9878dc3f..c6c77a505ec 100644 --- a/drivers/misc/acer-wmi.c +++ b/drivers/misc/acer-wmi.c @@ -192,6 +192,9 @@ static struct quirk_entry *quirks; static void set_quirks(void) { + if (!interface) + return; + if (quirks->mailled) interface->capability |= ACER_CAP_MAILLED; @@ -1237,6 +1240,8 @@ static int __init acer_wmi_init(void) return -ENODEV; } + set_quirks(); + if (platform_driver_register(&acer_platform_driver)) { printk(ACER_ERR "Unable to register platform driver.\n"); goto error_platform_register; -- GitLab From 060700b571717c997a2ea5e2049b848fa248ee13 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sun, 24 Aug 2008 11:52:06 -0700 Subject: [PATCH 736/750] x86: do not enable TSC notifier if we don't need it Impact: crash on non-TSC-equipped CPUs Don't enable the TSC notifier if we *either*: 1. don't have a CPU, or 2. have a CPU with constant TSC. In either of those cases, the notifier is either damaging (1) or useless(2). From: Linus Torvalds Signed-off-by: H. Peter Anvin --- arch/x86/kernel/tsc.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/x86/kernel/tsc.c b/arch/x86/kernel/tsc.c index 46af7167673..9bed5cae4bd 100644 --- a/arch/x86/kernel/tsc.c +++ b/arch/x86/kernel/tsc.c @@ -325,6 +325,10 @@ static struct notifier_block time_cpufreq_notifier_block = { static int __init cpufreq_tsc(void) { + if (!cpu_has_tsc) + return 0; + if (boot_cpu_has(X86_FEATURE_CONSTANT_TSC)) + return 0; cpufreq_register_notifier(&time_cpufreq_notifier_block, CPUFREQ_TRANSITION_NOTIFIER); return 0; -- GitLab From a2bd7274b47124d2fc4dfdb8c0591f545ba749dd Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Mon, 25 Aug 2008 00:56:08 -0700 Subject: [PATCH 737/750] x86: fix HPET regression in 2.6.26 versus 2.6.25, check hpet against BAR, v3 David Witbrodt tracked down (and bisected) a hpet bootup hang on his system to the following problem: a BIOS bug made the hpet device visible as a generic PCI device. If e820 reserved entries happen to be registered first in the resource tree [which v2.6.26 started doing], then the PCI code will reallocate that device's BAR to some other address - breaking timer IRQs and hanging the system. ( Normally hpet devices are hidden by the BIOS from the OS's PCI discovery via chipset magic. Sometimes the hpet is not a PCI device at all. ) Solve this fundamental fragility by making non-PCI platform drivers insert resources into the resource tree even if it overlaps the e820 reserved entry, to keep the resource manager from updating the BAR. Also do these checks for the ioapic and mmconfig addresses, and emit a warning if this happens. Bisected-by: David Witbrodt Signed-off-by: Yinghai Lu Tested-by: David Witbrodt Signed-off-by: Ingo Molnar --- arch/x86/pci/i386.c | 78 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 78 insertions(+) diff --git a/arch/x86/pci/i386.c b/arch/x86/pci/i386.c index 5807d1bc73f..d765da91384 100644 --- a/arch/x86/pci/i386.c +++ b/arch/x86/pci/i386.c @@ -31,8 +31,11 @@ #include #include #include +#include #include +#include +#include #include "pci.h" @@ -77,6 +80,77 @@ pcibios_align_resource(void *data, struct resource *res, } EXPORT_SYMBOL(pcibios_align_resource); +static int check_res_with_valid(struct pci_dev *dev, struct resource *res) +{ + unsigned long base; + unsigned long size; + int i; + + base = res->start; + size = (res->start == 0 && res->end == res->start) ? 0 : + (res->end - res->start + 1); + + if (!base || !size) + return 0; + +#ifdef CONFIG_HPET_TIMER + /* for hpet */ + if (base == hpet_address && (res->flags & IORESOURCE_MEM)) { + dev_info(&dev->dev, "BAR has HPET at %08lx-%08lx\n", + base, base + size - 1); + return 1; + } +#endif + +#ifdef CONFIG_X86_IO_APIC + for (i = 0; i < nr_ioapics; i++) { + unsigned long ioapic_phys = mp_ioapics[i].mp_apicaddr; + + if (base == ioapic_phys && (res->flags & IORESOURCE_MEM)) { + dev_info(&dev->dev, "BAR has ioapic at %08lx-%08lx\n", + base, base + size - 1); + return 1; + } + } +#endif + +#ifdef CONFIG_PCI_MMCONFIG + for (i = 0; i < pci_mmcfg_config_num; i++) { + unsigned long addr; + + addr = pci_mmcfg_config[i].address; + if (base == addr && (res->flags & IORESOURCE_MEM)) { + dev_info(&dev->dev, "BAR has MMCONFIG at %08lx-%08lx\n", + base, base + size - 1); + return 1; + } + } +#endif + + return 0; +} + +static int check_platform(struct pci_dev *dev, struct resource *res) +{ + struct resource *root = NULL; + + /* + * forcibly insert it into the + * resource tree + */ + if (res->flags & IORESOURCE_MEM) + root = &iomem_resource; + else if (res->flags & IORESOURCE_IO) + root = &ioport_resource; + + if (root && check_res_with_valid(dev, res)) { + insert_resource(root, res); + + return 1; + } + + return 0; +} /* * Handle resources of PCI devices. If the world were perfect, we could * just allocate all the resource regions and do nothing more. It isn't. @@ -128,6 +202,8 @@ static void __init pcibios_allocate_bus_resources(struct list_head *bus_list) pr = pci_find_parent_resource(dev, r); if (!r->start || !pr || request_resource(pr, r) < 0) { + if (check_platform(dev, r)) + continue; dev_err(&dev->dev, "BAR %d: can't " "allocate resource\n", idx); /* @@ -171,6 +247,8 @@ static void __init pcibios_allocate_resources(int pass) r->flags, disabled, pass); pr = pci_find_parent_resource(dev, r); if (!pr || request_resource(pr, r) < 0) { + if (check_platform(dev, r)) + continue; dev_err(&dev->dev, "BAR %d: can't " "allocate resource\n", idx); /* We'll assign a new address later */ -- GitLab From 52a8968ce95da8469ba0a9b3e4010fe31caf77a3 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Mon, 25 Aug 2008 13:35:06 +0200 Subject: [PATCH 738/750] x86: fix cpufreq + sched_clock() regression I noticed that my sched_clock() was slow on a number of machine, so I started looking at cpufreq. The below seems to fix the problem for me. Signed-off-by: Ingo Molnar --- arch/x86/kernel/tsc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/tsc.c b/arch/x86/kernel/tsc.c index 9bed5cae4bd..8e786b0d665 100644 --- a/arch/x86/kernel/tsc.c +++ b/arch/x86/kernel/tsc.c @@ -314,7 +314,7 @@ static int time_cpufreq_notifier(struct notifier_block *nb, unsigned long val, mark_tsc_unstable("cpufreq changes"); } - set_cyc2ns_scale(tsc_khz_ref, freq->cpu); + set_cyc2ns_scale(tsc_khz, freq->cpu); return 0; } -- GitLab From 2a61812af2e564cba2c8170cf96e1c823210f619 Mon Sep 17 00:00:00 2001 From: Austin Zhang Date: Mon, 25 Aug 2008 11:14:51 -0400 Subject: [PATCH 739/750] x86: add X86_FEATURE_XMM4_2 definitions Added Intel processor SSE4.2 feature flag. No in-tree user at the moment, but makes the tree-merging life easier for the crypto tree. Signed-off-by: Austin Zhang Signed-off-by: Ingo Molnar --- include/asm-x86/cpufeature.h | 2 ++ 1 file changed, 2 insertions(+) diff --git a/include/asm-x86/cpufeature.h b/include/asm-x86/cpufeature.h index 2f5a792b0ac..762f6a6bc70 100644 --- a/include/asm-x86/cpufeature.h +++ b/include/asm-x86/cpufeature.h @@ -91,6 +91,7 @@ #define X86_FEATURE_CX16 (4*32+13) /* CMPXCHG16B */ #define X86_FEATURE_XTPR (4*32+14) /* Send Task Priority Messages */ #define X86_FEATURE_DCA (4*32+18) /* Direct Cache Access */ +#define X86_FEATURE_XMM4_2 (4*32+20) /* Streaming SIMD Extensions-4.2 */ /* VIA/Cyrix/Centaur-defined CPU features, CPUID level 0xC0000001, word 5 */ #define X86_FEATURE_XSTORE (5*32+ 2) /* on-CPU RNG present (xstore insn) */ @@ -189,6 +190,7 @@ extern const char * const x86_power_flags[32]; #define cpu_has_gbpages boot_cpu_has(X86_FEATURE_GBPAGES) #define cpu_has_arch_perfmon boot_cpu_has(X86_FEATURE_ARCH_PERFMON) #define cpu_has_pat boot_cpu_has(X86_FEATURE_PAT) +#define cpu_has_xmm4_2 boot_cpu_has(X86_FEATURE_XMM4_2) #if defined(CONFIG_X86_INVLPG) || defined(CONFIG_X86_64) # define cpu_has_invlpg 1 -- GitLab From f73be6dedf4fa058ce80846dae604b08fa805ca1 Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Mon, 25 Aug 2008 17:07:14 -0700 Subject: [PATCH 740/750] smp: have smp_call_function_single() detect invalid CPUs Have smp_call_function_single() return invalid CPU indicies and return -ENXIO. This function is already executed inside a get_cpu()..put_cpu() which locks out CPU removal, so rather than having the higher layers doing another layer of locking to guard against unplugged CPUs do the test here. Signed-off-by: H. Peter Anvin --- kernel/smp.c | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-) diff --git a/kernel/smp.c b/kernel/smp.c index 782e2b93e46..f362a855377 100644 --- a/kernel/smp.c +++ b/kernel/smp.c @@ -210,8 +210,10 @@ int smp_call_function_single(int cpu, void (*func) (void *info), void *info, { struct call_single_data d; unsigned long flags; - /* prevent preemption and reschedule on another processor */ + /* prevent preemption and reschedule on another processor, + as well as CPU removal */ int me = get_cpu(); + int err = 0; /* Can deadlock when called with interrupts disabled */ WARN_ON(irqs_disabled()); @@ -220,7 +222,7 @@ int smp_call_function_single(int cpu, void (*func) (void *info), void *info, local_irq_save(flags); func(info); local_irq_restore(flags); - } else { + } else if ((unsigned)cpu < NR_CPUS && cpu_online(cpu)) { struct call_single_data *data = NULL; if (!wait) { @@ -236,10 +238,12 @@ int smp_call_function_single(int cpu, void (*func) (void *info), void *info, data->func = func; data->info = info; generic_exec_single(cpu, data); + } else { + err = -ENXIO; /* CPU not online */ } put_cpu(); - return 0; + return err; } EXPORT_SYMBOL(smp_call_function_single); -- GitLab From c6f31932d0a1d2b13952f506ebc92675e2d8df80 Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Mon, 25 Aug 2008 17:27:21 -0700 Subject: [PATCH 741/750] x86: msr: propagate errors from smp_call_function_single() Propagate error (-ENXIO) from smp_call_function_single(). These errors can happen when a CPU is unplugged while the MSR driver is open. Signed-off-by: H. Peter Anvin --- arch/x86/kernel/msr.c | 14 ++++++++++---- arch/x86/lib/msr-on-cpu.c | 22 ++++++++++++---------- include/asm-x86/msr.h | 11 ++++++----- 3 files changed, 28 insertions(+), 19 deletions(-) diff --git a/arch/x86/kernel/msr.c b/arch/x86/kernel/msr.c index e4393808688..9c34a1005db 100644 --- a/arch/x86/kernel/msr.c +++ b/arch/x86/kernel/msr.c @@ -79,8 +79,11 @@ static ssize_t msr_read(struct file *file, char __user *buf, for (; count; count -= 8) { err = rdmsr_safe_on_cpu(cpu, reg, &data[0], &data[1]); - if (err) - return -EIO; + if (err) { + if (err == -EFAULT) /* Fix idiotic error code */ + err = -EIO; + return err; + } if (copy_to_user(tmp, &data, 8)) return -EFAULT; tmp += 2; @@ -105,8 +108,11 @@ static ssize_t msr_write(struct file *file, const char __user *buf, if (copy_from_user(&data, tmp, 8)) return -EFAULT; err = wrmsr_safe_on_cpu(cpu, reg, data[0], data[1]); - if (err) - return -EIO; + if (err) { + if (err == -EFAULT) /* Fix idiotic error code */ + err = -EIO; + return err; + } tmp += 2; } diff --git a/arch/x86/lib/msr-on-cpu.c b/arch/x86/lib/msr-on-cpu.c index d5a2b39f882..01b868ba82f 100644 --- a/arch/x86/lib/msr-on-cpu.c +++ b/arch/x86/lib/msr-on-cpu.c @@ -30,10 +30,11 @@ static int _rdmsr_on_cpu(unsigned int cpu, u32 msr_no, u32 *l, u32 *h, int safe) rv.msr_no = msr_no; if (safe) { - smp_call_function_single(cpu, __rdmsr_safe_on_cpu, &rv, 1); - err = rv.err; + err = smp_call_function_single(cpu, __rdmsr_safe_on_cpu, + &rv, 1); + err = err ? err : rv.err; } else { - smp_call_function_single(cpu, __rdmsr_on_cpu, &rv, 1); + err = smp_call_function_single(cpu, __rdmsr_on_cpu, &rv, 1); } *l = rv.l; *h = rv.h; @@ -64,23 +65,24 @@ static int _wrmsr_on_cpu(unsigned int cpu, u32 msr_no, u32 l, u32 h, int safe) rv.l = l; rv.h = h; if (safe) { - smp_call_function_single(cpu, __wrmsr_safe_on_cpu, &rv, 1); - err = rv.err; + err = smp_call_function_single(cpu, __wrmsr_safe_on_cpu, + &rv, 1); + err = err ? err : rv.err; } else { - smp_call_function_single(cpu, __wrmsr_on_cpu, &rv, 1); + err = smp_call_function_single(cpu, __wrmsr_on_cpu, &rv, 1); } return err; } -void wrmsr_on_cpu(unsigned int cpu, u32 msr_no, u32 l, u32 h) +int wrmsr_on_cpu(unsigned int cpu, u32 msr_no, u32 l, u32 h) { - _wrmsr_on_cpu(cpu, msr_no, l, h, 0); + return _wrmsr_on_cpu(cpu, msr_no, l, h, 0); } -void rdmsr_on_cpu(unsigned int cpu, u32 msr_no, u32 *l, u32 *h) +int rdmsr_on_cpu(unsigned int cpu, u32 msr_no, u32 *l, u32 *h) { - _rdmsr_on_cpu(cpu, msr_no, l, h, 0); + return _rdmsr_on_cpu(cpu, msr_no, l, h, 0); } /* These "safe" variants are slower and should be used when the target MSR diff --git a/include/asm-x86/msr.h b/include/asm-x86/msr.h index ca110ee73f0..ad5f2decf7f 100644 --- a/include/asm-x86/msr.h +++ b/include/asm-x86/msr.h @@ -192,19 +192,20 @@ do { \ #define write_rdtscp_aux(val) wrmsr(0xc0000103, (val), 0) #ifdef CONFIG_SMP -void rdmsr_on_cpu(unsigned int cpu, u32 msr_no, u32 *l, u32 *h); -void wrmsr_on_cpu(unsigned int cpu, u32 msr_no, u32 l, u32 h); +int rdmsr_on_cpu(unsigned int cpu, u32 msr_no, u32 *l, u32 *h); +int wrmsr_on_cpu(unsigned int cpu, u32 msr_no, u32 l, u32 h); int rdmsr_safe_on_cpu(unsigned int cpu, u32 msr_no, u32 *l, u32 *h); - int wrmsr_safe_on_cpu(unsigned int cpu, u32 msr_no, u32 l, u32 h); #else /* CONFIG_SMP */ -static inline void rdmsr_on_cpu(unsigned int cpu, u32 msr_no, u32 *l, u32 *h) +static inline int rdmsr_on_cpu(unsigned int cpu, u32 msr_no, u32 *l, u32 *h) { rdmsr(msr_no, *l, *h); + return 0; } -static inline void wrmsr_on_cpu(unsigned int cpu, u32 msr_no, u32 l, u32 h) +static inline int wrmsr_on_cpu(unsigned int cpu, u32 msr_no, u32 l, u32 h) { wrmsr(msr_no, l, h); + return 0; } static inline int rdmsr_safe_on_cpu(unsigned int cpu, u32 msr_no, u32 *l, u32 *h) -- GitLab From 4b46ca701bdcdc19fcf32823f9fcabf8236e4e78 Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Mon, 25 Aug 2008 17:28:20 -0700 Subject: [PATCH 742/750] x86: cpuid: propagate error from smp_call_function_single() Propagate error (-ENXIO) from smp_call_function_single() in the CPUID driver. This can happen when a CPU is unplugged while the CPUID driver is open. Signed-off-by: H. Peter Anvin --- arch/x86/kernel/cpuid.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/arch/x86/kernel/cpuid.c b/arch/x86/kernel/cpuid.c index 14b11b3be31..23e8316c835 100644 --- a/arch/x86/kernel/cpuid.c +++ b/arch/x86/kernel/cpuid.c @@ -89,6 +89,7 @@ static ssize_t cpuid_read(struct file *file, char __user *buf, struct cpuid_regs cmd; int cpu = iminor(file->f_path.dentry->d_inode); u64 pos = *ppos; + int err; if (count % 16) return -EINVAL; /* Invalid chunk size */ @@ -96,7 +97,9 @@ static ssize_t cpuid_read(struct file *file, char __user *buf, for (; count; count -= 16) { cmd.eax = pos; cmd.ecx = pos >> 32; - smp_call_function_single(cpu, cpuid_smp_cpuid, &cmd, 1); + err = smp_call_function_single(cpu, cpuid_smp_cpuid, &cmd, 1); + if (err) + return err; if (copy_to_user(tmp, &cmd, 16)) return -EFAULT; tmp += 16; -- GitLab From 85f1cb60157e06d9e8996b02fad9ba6964523d75 Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Mon, 25 Aug 2008 17:34:27 -0700 Subject: [PATCH 743/750] x86: msr: correct return value on partial operations Return the correct return value when the MSR driver partially completes a request (we should return the number of bytes actually read or written, instead of the error code.) Signed-off-by: H. Peter Anvin --- arch/x86/kernel/msr.c | 28 ++++++++++++++++++---------- 1 file changed, 18 insertions(+), 10 deletions(-) diff --git a/arch/x86/kernel/msr.c b/arch/x86/kernel/msr.c index 9c34a1005db..2e2af5d1819 100644 --- a/arch/x86/kernel/msr.c +++ b/arch/x86/kernel/msr.c @@ -72,7 +72,8 @@ static ssize_t msr_read(struct file *file, char __user *buf, u32 data[2]; u32 reg = *ppos; int cpu = iminor(file->f_path.dentry->d_inode); - int err; + int err = 0; + ssize_t bytes = 0; if (count % 8) return -EINVAL; /* Invalid chunk size */ @@ -82,14 +83,17 @@ static ssize_t msr_read(struct file *file, char __user *buf, if (err) { if (err == -EFAULT) /* Fix idiotic error code */ err = -EIO; - return err; + break; + } + if (copy_to_user(tmp, &data, 8)) { + err = -EFAULT; + break; } - if (copy_to_user(tmp, &data, 8)) - return -EFAULT; tmp += 2; + bytes += 8; } - return ((char __user *)tmp) - buf; + return bytes ? bytes : err; } static ssize_t msr_write(struct file *file, const char __user *buf, @@ -99,24 +103,28 @@ static ssize_t msr_write(struct file *file, const char __user *buf, u32 data[2]; u32 reg = *ppos; int cpu = iminor(file->f_path.dentry->d_inode); - int err; + int err = 0; + ssize_t bytes = 0; if (count % 8) return -EINVAL; /* Invalid chunk size */ for (; count; count -= 8) { - if (copy_from_user(&data, tmp, 8)) - return -EFAULT; + if (copy_from_user(&data, tmp, 8)) { + err = -EFAULT; + break; + } err = wrmsr_safe_on_cpu(cpu, reg, data[0], data[1]); if (err) { if (err == -EFAULT) /* Fix idiotic error code */ err = -EIO; - return err; + break; } tmp += 2; + bytes += 8; } - return ((char __user *)tmp) - buf; + return bytes ? bytes : err; } static int msr_open(struct inode *inode, struct file *file) -- GitLab From 9ea2b82ed6265a31f9a84886d74d8a2ef01b27c8 Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Mon, 25 Aug 2008 17:35:25 -0700 Subject: [PATCH 744/750] x86: cpuid: correct return value on partial operations Return the correct return value when the CPUID driver partially completes a request (we should return the number of bytes actually read or written, instead of the error code.) Signed-off-by: H. Peter Anvin --- arch/x86/kernel/cpuid.c | 14 +++++++++----- 1 file changed, 9 insertions(+), 5 deletions(-) diff --git a/arch/x86/kernel/cpuid.c b/arch/x86/kernel/cpuid.c index 23e8316c835..8e9cd6a8ec1 100644 --- a/arch/x86/kernel/cpuid.c +++ b/arch/x86/kernel/cpuid.c @@ -89,7 +89,8 @@ static ssize_t cpuid_read(struct file *file, char __user *buf, struct cpuid_regs cmd; int cpu = iminor(file->f_path.dentry->d_inode); u64 pos = *ppos; - int err; + ssize_t bytes = 0; + int err = 0; if (count % 16) return -EINVAL; /* Invalid chunk size */ @@ -99,14 +100,17 @@ static ssize_t cpuid_read(struct file *file, char __user *buf, cmd.ecx = pos >> 32; err = smp_call_function_single(cpu, cpuid_smp_cpuid, &cmd, 1); if (err) - return err; - if (copy_to_user(tmp, &cmd, 16)) - return -EFAULT; + break; + if (copy_to_user(tmp, &cmd, 16)) { + err = -EFAULT; + break; + } tmp += 16; + bytes += 16; *ppos = ++pos; } - return tmp - buf; + return bytes ? bytes : err; } static int cpuid_open(struct inode *inode, struct file *file) -- GitLab From 08970fc4e0385790a7b093adfaa4165a189f9eb0 Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Mon, 25 Aug 2008 22:39:15 -0700 Subject: [PATCH 745/750] x86: msr: fix bogus return values from rdmsr_safe/wrmsr_safe Impact: bogus error codes (+other?) on x86-64 The rdmsr_safe/wrmsr_safe routines have macros for the handling of the edx:eax arguments. Those macros take a variable number of assembly arguments. This is rather inherently incompatible with using %digit-style escapes in the inline assembly; replace those with %[name]-style escapes. This fixes miscompilation on x86-64, which at the very least caused bogus return values. It is possible that this could also corrupt the return value; I am not sure. Signed-off-by: H. Peter Anvin --- include/asm-x86/msr.h | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) diff --git a/include/asm-x86/msr.h b/include/asm-x86/msr.h index ad5f2decf7f..2362cfda1fb 100644 --- a/include/asm-x86/msr.h +++ b/include/asm-x86/msr.h @@ -52,14 +52,14 @@ static inline unsigned long long native_read_msr_safe(unsigned int msr, { DECLARE_ARGS(val, low, high); - asm volatile("2: rdmsr ; xor %0,%0\n" + asm volatile("2: rdmsr ; xor %[err],%[err]\n" "1:\n\t" ".section .fixup,\"ax\"\n\t" - "3: mov %3,%0 ; jmp 1b\n\t" + "3: mov %[fault],%[err] ; jmp 1b\n\t" ".previous\n\t" _ASM_EXTABLE(2b, 3b) - : "=r" (*err), EAX_EDX_RET(val, low, high) - : "c" (msr), "i" (-EFAULT)); + : [err] "=r" (*err), EAX_EDX_RET(val, low, high) + : "c" (msr), [fault] "i" (-EFAULT)); return EAX_EDX_VAL(val, low, high); } @@ -73,15 +73,15 @@ static inline int native_write_msr_safe(unsigned int msr, unsigned low, unsigned high) { int err; - asm volatile("2: wrmsr ; xor %0,%0\n" + asm volatile("2: wrmsr ; xor %[err],%[err]\n" "1:\n\t" ".section .fixup,\"ax\"\n\t" - "3: mov %4,%0 ; jmp 1b\n\t" + "3: mov %[fault],%[err] ; jmp 1b\n\t" ".previous\n\t" _ASM_EXTABLE(2b, 3b) - : "=a" (err) + : [err] "=a" (err) : "c" (msr), "0" (low), "d" (high), - "i" (-EFAULT) + [fault] "i" (-EFAULT) : "memory"); return err; } -- GitLab From c1b362e3b4d331a63915b268a33207311a439d60 Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Mon, 25 Aug 2008 15:06:35 -0700 Subject: [PATCH 746/750] x86: update defconfigs Enable some option commonly used by testers in defconfig, including some very common device drivers and network boot support. defconfig is still not meant to be a kitchen-sink configuration. Signed-off-by: H. Peter Anvin --- arch/x86/configs/i386_defconfig | 303 +++++++++++++++++------------- arch/x86/configs/x86_64_defconfig | 258 +++++++++++++++---------- 2 files changed, 334 insertions(+), 227 deletions(-) diff --git a/arch/x86/configs/i386_defconfig b/arch/x86/configs/i386_defconfig index 4d73f53287b..104275e191a 100644 --- a/arch/x86/configs/i386_defconfig +++ b/arch/x86/configs/i386_defconfig @@ -1,13 +1,13 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.26-rc1 -# Sun May 4 19:59:02 2008 +# Linux kernel version: 2.6.27-rc4 +# Mon Aug 25 15:04:00 2008 # # CONFIG_64BIT is not set CONFIG_X86_32=y # CONFIG_X86_64 is not set CONFIG_X86=y -CONFIG_DEFCONFIG_LIST="arch/x86/configs/i386_defconfig" +CONFIG_ARCH_DEFCONFIG="arch/x86/configs/i386_defconfig" # CONFIG_GENERIC_LOCKBREAK is not set CONFIG_GENERIC_TIME=y CONFIG_GENERIC_CMOS_UPDATE=y @@ -53,6 +53,7 @@ CONFIG_X86_HT=y CONFIG_X86_BIOS_REBOOT=y CONFIG_X86_TRAMPOLINE=y CONFIG_KTIME_SCALAR=y +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" # # General setup @@ -82,6 +83,7 @@ CONFIG_CGROUPS=y CONFIG_CGROUP_NS=y # CONFIG_CGROUP_DEVICE is not set CONFIG_CPUSETS=y +CONFIG_HAVE_UNSTABLE_SCHED_CLOCK=y CONFIG_GROUP_SCHED=y CONFIG_FAIR_GROUP_SCHED=y # CONFIG_RT_GROUP_SCHED is not set @@ -105,7 +107,6 @@ CONFIG_SYSCTL=y # CONFIG_EMBEDDED is not set CONFIG_UID16=y CONFIG_SYSCTL_SYSCALL=y -CONFIG_SYSCTL_SYSCALL_CHECK=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_ALL=y CONFIG_KALLSYMS_EXTRA_PASS=y @@ -113,6 +114,7 @@ CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y +CONFIG_PCSPKR_PLATFORM=y # CONFIG_COMPAT_BRK is not set CONFIG_BASE_FULL=y CONFIG_FUTEX=y @@ -132,27 +134,35 @@ CONFIG_MARKERS=y # CONFIG_OPROFILE is not set CONFIG_HAVE_OPROFILE=y CONFIG_KPROBES=y +CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y CONFIG_KRETPROBES=y +CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y +# CONFIG_HAVE_ARCH_TRACEHOOK is not set # CONFIG_HAVE_DMA_ATTRS is not set +CONFIG_USE_GENERIC_SMP_HELPERS=y +# CONFIG_HAVE_CLK is not set CONFIG_PROC_PAGE_MONITOR=y +CONFIG_HAVE_GENERIC_DMA_COHERENT=y CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set CONFIG_MODULE_UNLOAD=y CONFIG_MODULE_FORCE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set -# CONFIG_KMOD is not set +CONFIG_KMOD=y CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y # CONFIG_LBD is not set CONFIG_BLK_DEV_IO_TRACE=y # CONFIG_LSF is not set CONFIG_BLK_DEV_BSG=y +# CONFIG_BLK_DEV_INTEGRITY is not set # # IO Schedulers @@ -176,19 +186,17 @@ CONFIG_NO_HZ=y CONFIG_HIGH_RES_TIMERS=y CONFIG_GENERIC_CLOCKEVENTS_BUILD=y CONFIG_SMP=y +CONFIG_X86_FIND_SMP_CONFIG=y +CONFIG_X86_MPPARSE=y CONFIG_X86_PC=y # CONFIG_X86_ELAN is not set # CONFIG_X86_VOYAGER is not set -# CONFIG_X86_NUMAQ is not set -# CONFIG_X86_SUMMIT is not set -# CONFIG_X86_BIGSMP is not set -# CONFIG_X86_VISWS is not set # CONFIG_X86_GENERICARCH is not set -# CONFIG_X86_ES7000 is not set -# CONFIG_X86_RDC321X is not set # CONFIG_X86_VSMP is not set +# CONFIG_X86_RDC321X is not set CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y # CONFIG_PARAVIRT_GUEST is not set +# CONFIG_MEMTEST is not set # CONFIG_M386 is not set # CONFIG_M486 is not set # CONFIG_M586 is not set @@ -215,21 +223,19 @@ CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y # CONFIG_MPSC is not set CONFIG_MCORE2=y # CONFIG_GENERIC_CPU is not set -# CONFIG_X86_GENERIC is not set +CONFIG_X86_GENERIC=y CONFIG_X86_CPU=y CONFIG_X86_CMPXCHG=y -CONFIG_X86_L1_CACHE_SHIFT=6 +CONFIG_X86_L1_CACHE_SHIFT=7 CONFIG_X86_XADD=y CONFIG_X86_WP_WORKS_OK=y CONFIG_X86_INVLPG=y CONFIG_X86_BSWAP=y CONFIG_X86_POPAD_OK=y -CONFIG_X86_GOOD_APIC=y CONFIG_X86_INTEL_USERCOPY=y CONFIG_X86_USE_PPRO_CHECKSUM=y -CONFIG_X86_P6_NOP=y CONFIG_X86_TSC=y -CONFIG_X86_MINIMUM_CPU_FAMILY=6 +CONFIG_X86_MINIMUM_CPU_FAMILY=4 CONFIG_X86_DEBUGCTLMSR=y CONFIG_HPET_TIMER=y CONFIG_HPET_EMULATE_RTC=y @@ -247,7 +253,7 @@ CONFIG_X86_IO_APIC=y CONFIG_VM86=y # CONFIG_TOSHIBA is not set # CONFIG_I8K is not set -# CONFIG_X86_REBOOTFIXUPS is not set +CONFIG_X86_REBOOTFIXUPS=y # CONFIG_MICROCODE is not set CONFIG_X86_MSR=y CONFIG_X86_CPUID=y @@ -256,32 +262,28 @@ CONFIG_HIGHMEM4G=y # CONFIG_HIGHMEM64G is not set CONFIG_PAGE_OFFSET=0xC0000000 CONFIG_HIGHMEM=y -CONFIG_NEED_NODE_MEMMAP_SIZE=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_ARCH_SPARSEMEM_ENABLE=y CONFIG_ARCH_SELECT_MEMORY_MODEL=y CONFIG_SELECT_MEMORY_MODEL=y -# CONFIG_FLATMEM_MANUAL is not set +CONFIG_FLATMEM_MANUAL=y # CONFIG_DISCONTIGMEM_MANUAL is not set -CONFIG_SPARSEMEM_MANUAL=y -CONFIG_SPARSEMEM=y -CONFIG_HAVE_MEMORY_PRESENT=y +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_SPARSEMEM_STATIC=y # CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set - -# -# Memory hotplug is currently incompatible with Software Suspend -# CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_RESOURCES_64BIT=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -# CONFIG_HIGHPTE is not set +CONFIG_HIGHPTE=y # CONFIG_MATH_EMULATION is not set CONFIG_MTRR=y -# CONFIG_X86_PAT is not set +# CONFIG_MTRR_SANITIZER is not set +CONFIG_X86_PAT=y CONFIG_EFI=y # CONFIG_IRQBALANCE is not set CONFIG_SECCOMP=y @@ -293,6 +295,7 @@ CONFIG_HZ=1000 CONFIG_SCHED_HRTICK=y CONFIG_KEXEC=y CONFIG_CRASH_DUMP=y +# CONFIG_KEXEC_JUMP is not set CONFIG_PHYSICAL_START=0x1000000 CONFIG_RELOCATABLE=y CONFIG_PHYSICAL_ALIGN=0x200000 @@ -312,6 +315,7 @@ CONFIG_PM_TRACE_RTC=y CONFIG_PM_SLEEP_SMP=y CONFIG_PM_SLEEP=y CONFIG_SUSPEND=y +# CONFIG_PM_TEST_SUSPEND is not set CONFIG_SUSPEND_FREEZER=y CONFIG_HIBERNATION=y CONFIG_PM_STD_PARTITION="" @@ -337,6 +341,7 @@ CONFIG_ACPI_THERMAL=y CONFIG_ACPI_BLACKLIST_YEAR=0 # CONFIG_ACPI_DEBUG is not set CONFIG_ACPI_EC=y +# CONFIG_ACPI_PCI_SLOT is not set CONFIG_ACPI_POWER=y CONFIG_ACPI_SYSTEM=y CONFIG_X86_PM_TIMER=y @@ -395,8 +400,8 @@ CONFIG_PCI=y # CONFIG_PCI_GOBIOS is not set # CONFIG_PCI_GOMMCONFIG is not set # CONFIG_PCI_GODIRECT is not set -CONFIG_PCI_GOANY=y # CONFIG_PCI_GOOLPC is not set +CONFIG_PCI_GOANY=y CONFIG_PCI_BIOS=y CONFIG_PCI_DIRECT=y CONFIG_PCI_MMCONFIG=y @@ -448,10 +453,6 @@ CONFIG_HOTPLUG_PCI=y CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_AOUT is not set CONFIG_BINFMT_MISC=y - -# -# Networking -# CONFIG_NET=y # @@ -475,7 +476,10 @@ CONFIG_IP_FIB_HASH=y CONFIG_IP_MULTIPLE_TABLES=y CONFIG_IP_ROUTE_MULTIPATH=y CONFIG_IP_ROUTE_VERBOSE=y -# CONFIG_IP_PNP is not set +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y # CONFIG_NET_IPIP is not set # CONFIG_NET_IPGRE is not set CONFIG_IP_MROUTE=y @@ -618,7 +622,6 @@ CONFIG_NET_SCHED=y # CONFIG_NET_SCH_HTB is not set # CONFIG_NET_SCH_HFSC is not set # CONFIG_NET_SCH_PRIO is not set -# CONFIG_NET_SCH_RR is not set # CONFIG_NET_SCH_RED is not set # CONFIG_NET_SCH_SFQ is not set # CONFIG_NET_SCH_TEQL is not set @@ -680,28 +683,19 @@ CONFIG_FIB_RULES=y CONFIG_CFG80211=y CONFIG_NL80211=y CONFIG_WIRELESS_EXT=y +CONFIG_WIRELESS_EXT_SYSFS=y CONFIG_MAC80211=y # # Rate control algorithm selection # +CONFIG_MAC80211_RC_PID=y CONFIG_MAC80211_RC_DEFAULT_PID=y -# CONFIG_MAC80211_RC_DEFAULT_NONE is not set - -# -# Selecting 'y' for an algorithm will -# - -# -# build the algorithm into mac80211. -# CONFIG_MAC80211_RC_DEFAULT="pid" -CONFIG_MAC80211_RC_PID=y # CONFIG_MAC80211_MESH is not set CONFIG_MAC80211_LEDS=y # CONFIG_MAC80211_DEBUGFS is not set -# CONFIG_MAC80211_DEBUG_PACKET_ALIGNMENT is not set -# CONFIG_MAC80211_DEBUG is not set +# CONFIG_MAC80211_DEBUG_MENU is not set # CONFIG_IEEE80211 is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -717,6 +711,8 @@ CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_EXTRA_FIRMWARE="" # CONFIG_DEBUG_DRIVER is not set CONFIG_DEBUG_DEVRES=y # CONFIG_SYS_HYPERVISOR is not set @@ -749,6 +745,7 @@ CONFIG_BLK_DEV_RAM_SIZE=16384 # CONFIG_BLK_DEV_XIP is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set +# CONFIG_BLK_DEV_HD is not set CONFIG_MISC_DEVICES=y # CONFIG_IBM_ASM is not set # CONFIG_PHANTOM is not set @@ -760,10 +757,12 @@ CONFIG_MISC_DEVICES=y # CONFIG_FUJITSU_LAPTOP is not set # CONFIG_TC1100_WMI is not set # CONFIG_MSI_LAPTOP is not set +# CONFIG_COMPAL_LAPTOP is not set # CONFIG_SONY_LAPTOP is not set # CONFIG_THINKPAD_ACPI is not set # CONFIG_INTEL_MENLOW is not set # CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_HP_ILO is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -802,12 +801,13 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_SPI_ATTRS=y # CONFIG_SCSI_FC_ATTRS is not set -# CONFIG_SCSI_ISCSI_ATTRS is not set +CONFIG_SCSI_ISCSI_ATTRS=y # CONFIG_SCSI_SAS_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set # CONFIG_SCSI_SRP_ATTRS is not set # CONFIG_SCSI_LOWLEVEL is not set # CONFIG_SCSI_LOWLEVEL_PCMCIA is not set +# CONFIG_SCSI_DH is not set CONFIG_ATA=y # CONFIG_ATA_NONSTANDARD is not set CONFIG_ATA_ACPI=y @@ -842,7 +842,7 @@ CONFIG_PATA_AMD=y # CONFIG_PATA_CS5536 is not set # CONFIG_PATA_CYPRESS is not set # CONFIG_PATA_EFAR is not set -# CONFIG_ATA_GENERIC is not set +CONFIG_ATA_GENERIC=y # CONFIG_PATA_HPT366 is not set # CONFIG_PATA_HPT37X is not set # CONFIG_PATA_HPT3X2N is not set @@ -852,7 +852,7 @@ CONFIG_PATA_AMD=y # CONFIG_PATA_JMICRON is not set # CONFIG_PATA_TRIFLEX is not set # CONFIG_PATA_MARVELL is not set -# CONFIG_PATA_MPIIX is not set +CONFIG_PATA_MPIIX=y CONFIG_PATA_OLDPIIX=y # CONFIG_PATA_NETCELL is not set # CONFIG_PATA_NINJA32 is not set @@ -871,6 +871,7 @@ CONFIG_PATA_OLDPIIX=y # CONFIG_PATA_SIS is not set # CONFIG_PATA_VIA is not set # CONFIG_PATA_WINBOND is not set +CONFIG_PATA_SCH=y CONFIG_MD=y CONFIG_BLK_DEV_MD=y # CONFIG_MD_LINEAR is not set @@ -894,13 +895,16 @@ CONFIG_DM_ZERO=y # # IEEE 1394 (FireWire) support # + +# +# Enable only one of the two stacks, unless you know what you are doing +# # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set CONFIG_MACINTOSH_DRIVERS=y CONFIG_MAC_EMUMOUSEBTN=y CONFIG_NETDEVICES=y -# CONFIG_NETDEVICES_MULTIQUEUE is not set # CONFIG_IFB is not set # CONFIG_DUMMY is not set # CONFIG_BONDING is not set @@ -910,7 +914,23 @@ CONFIG_NETDEVICES=y # CONFIG_VETH is not set # CONFIG_NET_SB1000 is not set # CONFIG_ARCNET is not set -# CONFIG_PHYLIB is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_REALTEK_PHY is not set +# CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -943,10 +963,10 @@ CONFIG_FORCEDETH=y CONFIG_E100=y # CONFIG_FEALNX is not set # CONFIG_NATSEMI is not set -# CONFIG_NE2K_PCI is not set +CONFIG_NE2K_PCI=y # CONFIG_8139CP is not set CONFIG_8139TOO=y -CONFIG_8139TOO_PIO=y +# CONFIG_8139TOO_PIO is not set # CONFIG_8139TOO_TUNE_TWISTER is not set # CONFIG_8139TOO_8129 is not set # CONFIG_8139_OLD_RX_RESET is not set @@ -961,25 +981,24 @@ CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set CONFIG_E1000=y -# CONFIG_E1000_NAPI is not set # CONFIG_E1000_DISABLE_PACKET_SPLIT is not set -# CONFIG_E1000E is not set -# CONFIG_E1000E_ENABLED is not set +CONFIG_E1000E=y # CONFIG_IP1000 is not set # CONFIG_IGB is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set -# CONFIG_R8169 is not set +CONFIG_R8169=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set CONFIG_SKY2=y # CONFIG_SKY2_DEBUG is not set # CONFIG_VIA_VELOCITY is not set CONFIG_TIGON3=y -# CONFIG_BNX2 is not set +CONFIG_BNX2=y # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set +# CONFIG_ATL1E is not set CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set @@ -1019,13 +1038,14 @@ CONFIG_WLAN_80211=y # CONFIG_RTL8180 is not set # CONFIG_RTL8187 is not set # CONFIG_ADM8211 is not set +# CONFIG_MAC80211_HWSIM is not set # CONFIG_P54_COMMON is not set CONFIG_ATH5K=y # CONFIG_ATH5K_DEBUG is not set -# CONFIG_IWLWIFI is not set +# CONFIG_ATH9K is not set # CONFIG_IWLCORE is not set # CONFIG_IWLWIFI_LEDS is not set -# CONFIG_IWL4965 is not set +# CONFIG_IWLAGN is not set # CONFIG_IWL3945 is not set # CONFIG_HOSTAP is not set # CONFIG_B43 is not set @@ -1105,6 +1125,7 @@ CONFIG_MOUSE_PS2_TRACKPOINT=y # CONFIG_MOUSE_PS2_TOUCHKIT is not set # CONFIG_MOUSE_SERIAL is not set # CONFIG_MOUSE_APPLETOUCH is not set +# CONFIG_MOUSE_BCM5974 is not set # CONFIG_MOUSE_VSXXXAA is not set CONFIG_INPUT_JOYSTICK=y # CONFIG_JOYSTICK_ANALOG is not set @@ -1139,12 +1160,14 @@ CONFIG_INPUT_TOUCHSCREEN=y # CONFIG_TOUCHSCREEN_GUNZE is not set # CONFIG_TOUCHSCREEN_ELO is not set # CONFIG_TOUCHSCREEN_MTOUCH is not set +# CONFIG_TOUCHSCREEN_INEXIO is not set # CONFIG_TOUCHSCREEN_MK712 is not set # CONFIG_TOUCHSCREEN_PENMOUNT is not set # CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set # CONFIG_TOUCHSCREEN_TOUCHWIN is not set # CONFIG_TOUCHSCREEN_UCB1400 is not set # CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set +# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set CONFIG_INPUT_MISC=y # CONFIG_INPUT_PCSPKR is not set # CONFIG_INPUT_APANEL is not set @@ -1173,6 +1196,7 @@ CONFIG_SERIO_LIBPS2=y # Character devices # CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y CONFIG_VT_HW_CONSOLE_BINDING=y @@ -1223,8 +1247,8 @@ CONFIG_UNIX98_PTYS=y # CONFIG_LEGACY_PTYS is not set # CONFIG_IPMI_HANDLER is not set CONFIG_HW_RANDOM=y -# CONFIG_HW_RANDOM_INTEL is not set -# CONFIG_HW_RANDOM_AMD is not set +CONFIG_HW_RANDOM_INTEL=y +CONFIG_HW_RANDOM_AMD=y CONFIG_HW_RANDOM_GEODE=y CONFIG_HW_RANDOM_VIA=y CONFIG_NVRAM=y @@ -1245,7 +1269,6 @@ CONFIG_NVRAM=y # CONFIG_CS5535_GPIO is not set # CONFIG_RAW_DRIVER is not set CONFIG_HPET=y -# CONFIG_HPET_RTC_IRQ is not set # CONFIG_HPET_MMAP is not set # CONFIG_HANGCHECK_TIMER is not set # CONFIG_TCG_TPM is not set @@ -1254,43 +1277,64 @@ CONFIG_DEVPORT=y CONFIG_I2C=y CONFIG_I2C_BOARDINFO=y # CONFIG_I2C_CHARDEV is not set +CONFIG_I2C_HELPER_AUTO=y # # I2C Hardware Bus support # + +# +# PC SMBus host controller drivers +# # CONFIG_I2C_ALI1535 is not set # CONFIG_I2C_ALI1563 is not set # CONFIG_I2C_ALI15X3 is not set # CONFIG_I2C_AMD756 is not set # CONFIG_I2C_AMD8111 is not set CONFIG_I2C_I801=y -# CONFIG_I2C_I810 is not set +# CONFIG_I2C_ISCH is not set # CONFIG_I2C_PIIX4 is not set # CONFIG_I2C_NFORCE2 is not set -# CONFIG_I2C_OCORES is not set -# CONFIG_I2C_PARPORT_LIGHT is not set -# CONFIG_I2C_PROSAVAGE is not set -# CONFIG_I2C_SAVAGE4 is not set -# CONFIG_I2C_SIMTEC is not set -# CONFIG_SCx200_ACB is not set # CONFIG_I2C_SIS5595 is not set # CONFIG_I2C_SIS630 is not set # CONFIG_I2C_SIS96X is not set -# CONFIG_I2C_TAOS_EVM is not set -# CONFIG_I2C_STUB is not set -# CONFIG_I2C_TINY_USB is not set # CONFIG_I2C_VIA is not set # CONFIG_I2C_VIAPRO is not set + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_TINY_USB is not set + +# +# Graphics adapter I2C/DDC channel drivers +# # CONFIG_I2C_VOODOO3 is not set + +# +# Other I2C/SMBus bus drivers +# # CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set +# CONFIG_SCx200_ACB is not set # # Miscellaneous I2C Chip support # # CONFIG_DS1682 is not set +# CONFIG_AT24 is not set # CONFIG_SENSORS_EEPROM is not set # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set # CONFIG_SENSORS_PCF8591 is not set # CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set @@ -1299,6 +1343,8 @@ CONFIG_I2C_I801=y # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set +CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y +# CONFIG_GPIOLIB is not set # CONFIG_W1 is not set CONFIG_POWER_SUPPLY=y # CONFIG_POWER_SUPPLY_DEBUG is not set @@ -1360,8 +1406,10 @@ CONFIG_SSB_POSSIBLE=y # # Multifunction device drivers # +# CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set # # Multimedia devices @@ -1372,6 +1420,7 @@ CONFIG_SSB_POSSIBLE=y # # CONFIG_VIDEO_DEV is not set # CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set # # Multimedia drivers @@ -1418,7 +1467,6 @@ CONFIG_FB_CFB_IMAGEBLIT=y # CONFIG_FB_SYS_IMAGEBLIT is not set # CONFIG_FB_FOREIGN_ENDIAN is not set # CONFIG_FB_SYS_FOPS is not set -CONFIG_FB_DEFERRED_IO=y # CONFIG_FB_SVGALIB is not set # CONFIG_FB_MACMODES is not set # CONFIG_FB_BACKLIGHT is not set @@ -1463,6 +1511,7 @@ CONFIG_FB_EFI=y # CONFIG_FB_TRIDENT is not set # CONFIG_FB_ARK is not set # CONFIG_FB_PM3 is not set +# CONFIG_FB_CARMINE is not set # CONFIG_FB_GEODE is not set # CONFIG_FB_VIRTUAL is not set CONFIG_BACKLIGHT_LCD_SUPPORT=y @@ -1470,6 +1519,7 @@ CONFIG_BACKLIGHT_LCD_SUPPORT=y CONFIG_BACKLIGHT_CLASS_DEVICE=y # CONFIG_BACKLIGHT_CORGI is not set # CONFIG_BACKLIGHT_PROGEAR is not set +# CONFIG_BACKLIGHT_MBP_NVIDIA is not set # # Display device support @@ -1489,15 +1539,7 @@ CONFIG_LOGO=y # CONFIG_LOGO_LINUX_MONO is not set # CONFIG_LOGO_LINUX_VGA16 is not set CONFIG_LOGO_LINUX_CLUT224=y - -# -# Sound -# CONFIG_SOUND=y - -# -# Advanced Linux Sound Architecture -# CONFIG_SND=y CONFIG_SND_TIMER=y CONFIG_SND_PCM=y @@ -1515,20 +1557,14 @@ CONFIG_SND_VERBOSE_PROCFS=y # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set CONFIG_SND_VMASTER=y - -# -# Generic devices -# +CONFIG_SND_DRIVERS=y # CONFIG_SND_PCSP is not set # CONFIG_SND_DUMMY is not set # CONFIG_SND_VIRMIDI is not set # CONFIG_SND_MTPAV is not set # CONFIG_SND_SERIAL_U16550 is not set # CONFIG_SND_MPU401 is not set - -# -# PCI devices -# +CONFIG_SND_PCI=y # CONFIG_SND_AD1889 is not set # CONFIG_SND_ALS300 is not set # CONFIG_SND_ALS4000 is not set @@ -1603,36 +1639,14 @@ CONFIG_SND_HDA_GENERIC=y # CONFIG_SND_VIRTUOSO is not set # CONFIG_SND_VX222 is not set # CONFIG_SND_YMFPCI is not set - -# -# USB devices -# +CONFIG_SND_USB=y # CONFIG_SND_USB_AUDIO is not set # CONFIG_SND_USB_USX2Y is not set # CONFIG_SND_USB_CAIAQ is not set - -# -# PCMCIA devices -# +CONFIG_SND_PCMCIA=y # CONFIG_SND_VXPOCKET is not set # CONFIG_SND_PDAUDIOCF is not set - -# -# System on Chip audio support -# # CONFIG_SND_SOC is not set - -# -# ALSA SoC audio for Freescale SOCs -# - -# -# SoC Audio for the Texas Instruments OMAP -# - -# -# Open Sound System -# # CONFIG_SOUND_PRIME is not set CONFIG_HID_SUPPORT=y CONFIG_HID=y @@ -1668,6 +1682,7 @@ CONFIG_USB_DEVICEFS=y # CONFIG_USB_DYNAMIC_MINORS is not set CONFIG_USB_SUSPEND=y # CONFIG_USB_OTG is not set +CONFIG_USB_MON=y # # USB Host Controller Drivers @@ -1691,6 +1706,7 @@ CONFIG_USB_UHCI_HCD=y # # CONFIG_USB_ACM is not set CONFIG_USB_PRINTER=y +# CONFIG_USB_WDM is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -1712,6 +1728,7 @@ CONFIG_USB_STORAGE=y # CONFIG_USB_STORAGE_ALAUDA is not set # CONFIG_USB_STORAGE_ONETOUCH is not set # CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_SIERRA is not set # CONFIG_USB_STORAGE_CYPRESS_ATACB is not set CONFIG_USB_LIBUSUAL=y @@ -1720,7 +1737,6 @@ CONFIG_USB_LIBUSUAL=y # # CONFIG_USB_MDC800 is not set # CONFIG_USB_MICROTEK is not set -CONFIG_USB_MON=y # # USB port drivers @@ -1733,7 +1749,6 @@ CONFIG_USB_MON=y # CONFIG_USB_EMI62 is not set # CONFIG_USB_EMI26 is not set # CONFIG_USB_ADUTUX is not set -# CONFIG_USB_AUERSWALD is not set # CONFIG_USB_RIO500 is not set # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set @@ -1750,6 +1765,7 @@ CONFIG_USB_MON=y # CONFIG_USB_TRANCEVIBRATOR is not set # CONFIG_USB_IOWARRIOR is not set # CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set # CONFIG_USB_GADGET is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set @@ -1759,7 +1775,9 @@ CONFIG_LEDS_CLASS=y # # LED drivers # +# CONFIG_LEDS_PCA9532 is not set # CONFIG_LEDS_CLEVO_MAIL is not set +# CONFIG_LEDS_PCA955X is not set # # LED Triggers @@ -1805,6 +1823,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_PCF8583 is not set # CONFIG_RTC_DRV_M41T80 is not set # CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set # # SPI RTC drivers @@ -1837,11 +1856,13 @@ CONFIG_DMADEVICES=y # Firmware Drivers # # CONFIG_EDD is not set +CONFIG_FIRMWARE_MEMMAP=y CONFIG_EFI_VARS=y # CONFIG_DELL_RBU is not set # CONFIG_DCDBAS is not set CONFIG_DMIID=y -# CONFIG_ISCSI_IBFT_FIND is not set +CONFIG_ISCSI_IBFT_FIND=y +CONFIG_ISCSI_IBFT=y # # File systems @@ -1920,14 +1941,27 @@ CONFIG_HUGETLB_PAGE=y # CONFIG_CRAMFS is not set # CONFIG_VXFS_FS is not set # CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_ROMFS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set CONFIG_NETWORK_FILESYSTEMS=y -# CONFIG_NFS_FS is not set +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +CONFIG_NFS_V3_ACL=y +CONFIG_NFS_V4=y +CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_ACL_SUPPORT=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set # CONFIG_CIFS is not set # CONFIG_NCP_FS is not set @@ -2001,9 +2035,9 @@ CONFIG_NLS_UTF8=y # Kernel hacking # CONFIG_TRACE_IRQFLAGS_SUPPORT=y -# CONFIG_PRINTK_TIME is not set -# CONFIG_ENABLE_WARN_DEPRECATED is not set -# CONFIG_ENABLE_MUST_CHECK is not set +CONFIG_PRINTK_TIME=y +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y CONFIG_FRAME_WARN=2048 CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -2033,6 +2067,7 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_WRITECOUNT is not set +CONFIG_DEBUG_MEMORY_INIT=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set CONFIG_FRAME_POINTER=y @@ -2043,23 +2078,32 @@ CONFIG_FRAME_POINTER=y # CONFIG_LKDTM is not set # CONFIG_FAULT_INJECTION is not set # CONFIG_LATENCYTOP is not set +CONFIG_SYSCTL_SYSCALL_CHECK=y +CONFIG_HAVE_FTRACE=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +# CONFIG_FTRACE is not set +# CONFIG_IRQSOFF_TRACER is not set +# CONFIG_SYSPROF_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set CONFIG_PROVIDE_OHCI1394_DMA_INIT=y # CONFIG_SAMPLES is not set -# CONFIG_KGDB is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set # CONFIG_STRICT_DEVMEM is not set +CONFIG_X86_VERBOSE_BOOTUP=y CONFIG_EARLY_PRINTK=y CONFIG_DEBUG_STACKOVERFLOW=y CONFIG_DEBUG_STACK_USAGE=y # CONFIG_DEBUG_PAGEALLOC is not set +# CONFIG_DEBUG_PER_CPU_MAPS is not set # CONFIG_X86_PTDUMP is not set CONFIG_DEBUG_RODATA=y # CONFIG_DEBUG_RODATA_TEST is not set CONFIG_DEBUG_NX_TEST=m # CONFIG_4KSTACKS is not set -CONFIG_X86_FIND_SMP_CONFIG=y -CONFIG_X86_MPPARSE=y CONFIG_DOUBLEFAULT=y +# CONFIG_MMIOTRACE is not set CONFIG_IO_DELAY_TYPE_0X80=0 CONFIG_IO_DELAY_TYPE_0XED=1 CONFIG_IO_DELAY_TYPE_UDELAY=2 @@ -2071,6 +2115,7 @@ CONFIG_IO_DELAY_0X80=y CONFIG_DEFAULT_IO_DELAY_TYPE=0 CONFIG_DEBUG_BOOT_PARAMS=y # CONFIG_CPA_DEBUG is not set +# CONFIG_OPTIMIZE_INLINING is not set # # Security options @@ -2080,7 +2125,6 @@ CONFIG_KEYS_DEBUG_PROC_KEYS=y CONFIG_SECURITY=y CONFIG_SECURITY_NETWORK=y # CONFIG_SECURITY_NETWORK_XFRM is not set -CONFIG_SECURITY_CAPABILITIES=y CONFIG_SECURITY_FILE_CAPABILITIES=y # CONFIG_SECURITY_ROOTPLUG is not set CONFIG_SECURITY_DEFAULT_MMAP_MIN_ADDR=65536 @@ -2141,6 +2185,10 @@ CONFIG_CRYPTO_HMAC=y # CONFIG_CRYPTO_MD4 is not set CONFIG_CRYPTO_MD5=y # CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set CONFIG_CRYPTO_SHA1=y # CONFIG_CRYPTO_SHA256 is not set # CONFIG_CRYPTO_SHA512 is not set @@ -2151,7 +2199,7 @@ CONFIG_CRYPTO_SHA1=y # Ciphers # CONFIG_CRYPTO_AES=y -# CONFIG_CRYPTO_AES_586 is not set +CONFIG_CRYPTO_AES_586=y # CONFIG_CRYPTO_ANUBIS is not set CONFIG_CRYPTO_ARC4=y # CONFIG_CRYPTO_BLOWFISH is not set @@ -2193,6 +2241,7 @@ CONFIG_GENERIC_FIND_FIRST_BIT=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_CRC_CCITT is not set # CONFIG_CRC16 is not set +CONFIG_CRC_T10DIF=y # CONFIG_CRC_ITU_T is not set CONFIG_CRC32=y # CONFIG_CRC7 is not set diff --git a/arch/x86/configs/x86_64_defconfig b/arch/x86/configs/x86_64_defconfig index a4045242962..678c8acefe0 100644 --- a/arch/x86/configs/x86_64_defconfig +++ b/arch/x86/configs/x86_64_defconfig @@ -1,13 +1,13 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.26-rc1 -# Sun May 4 19:59:57 2008 +# Linux kernel version: 2.6.27-rc4 +# Mon Aug 25 14:40:46 2008 # CONFIG_64BIT=y # CONFIG_X86_32 is not set CONFIG_X86_64=y CONFIG_X86=y -CONFIG_DEFCONFIG_LIST="arch/x86/configs/x86_64_defconfig" +CONFIG_ARCH_DEFCONFIG="arch/x86/configs/x86_64_defconfig" # CONFIG_GENERIC_LOCKBREAK is not set CONFIG_GENERIC_TIME=y CONFIG_GENERIC_CMOS_UPDATE=y @@ -53,6 +53,7 @@ CONFIG_X86_HT=y CONFIG_X86_BIOS_REBOOT=y CONFIG_X86_TRAMPOLINE=y # CONFIG_KTIME_SCALAR is not set +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" # # General setup @@ -82,6 +83,7 @@ CONFIG_CGROUPS=y CONFIG_CGROUP_NS=y # CONFIG_CGROUP_DEVICE is not set CONFIG_CPUSETS=y +CONFIG_HAVE_UNSTABLE_SCHED_CLOCK=y CONFIG_GROUP_SCHED=y CONFIG_FAIR_GROUP_SCHED=y # CONFIG_RT_GROUP_SCHED is not set @@ -105,7 +107,6 @@ CONFIG_SYSCTL=y # CONFIG_EMBEDDED is not set CONFIG_UID16=y CONFIG_SYSCTL_SYSCALL=y -CONFIG_SYSCTL_SYSCALL_CHECK=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_ALL=y CONFIG_KALLSYMS_EXTRA_PASS=y @@ -113,6 +114,7 @@ CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y +CONFIG_PCSPKR_PLATFORM=y # CONFIG_COMPAT_BRK is not set CONFIG_BASE_FULL=y CONFIG_FUTEX=y @@ -132,25 +134,33 @@ CONFIG_MARKERS=y # CONFIG_OPROFILE is not set CONFIG_HAVE_OPROFILE=y CONFIG_KPROBES=y +CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y CONFIG_KRETPROBES=y +CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y +# CONFIG_HAVE_ARCH_TRACEHOOK is not set # CONFIG_HAVE_DMA_ATTRS is not set +CONFIG_USE_GENERIC_SMP_HELPERS=y +# CONFIG_HAVE_CLK is not set CONFIG_PROC_PAGE_MONITOR=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set CONFIG_MODULE_UNLOAD=y CONFIG_MODULE_FORCE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set -# CONFIG_KMOD is not set +CONFIG_KMOD=y CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y CONFIG_BLK_DEV_IO_TRACE=y CONFIG_BLK_DEV_BSG=y +# CONFIG_BLK_DEV_INTEGRITY is not set CONFIG_BLOCK_COMPAT=y # @@ -175,20 +185,15 @@ CONFIG_NO_HZ=y CONFIG_HIGH_RES_TIMERS=y CONFIG_GENERIC_CLOCKEVENTS_BUILD=y CONFIG_SMP=y +CONFIG_X86_FIND_SMP_CONFIG=y +CONFIG_X86_MPPARSE=y CONFIG_X86_PC=y # CONFIG_X86_ELAN is not set # CONFIG_X86_VOYAGER is not set -# CONFIG_X86_NUMAQ is not set -# CONFIG_X86_SUMMIT is not set -# CONFIG_X86_BIGSMP is not set -# CONFIG_X86_VISWS is not set # CONFIG_X86_GENERICARCH is not set -# CONFIG_X86_ES7000 is not set -# CONFIG_X86_RDC321X is not set # CONFIG_X86_VSMP is not set # CONFIG_PARAVIRT_GUEST is not set -CONFIG_MEMTEST_BOOTPARAM=y -CONFIG_MEMTEST_BOOTPARAM_VALUE=0 +# CONFIG_MEMTEST is not set # CONFIG_M386 is not set # CONFIG_M486 is not set # CONFIG_M586 is not set @@ -220,11 +225,12 @@ CONFIG_X86_L1_CACHE_BYTES=64 CONFIG_X86_INTERNODE_CACHE_BYTES=64 CONFIG_X86_CMPXCHG=y CONFIG_X86_L1_CACHE_SHIFT=6 -CONFIG_X86_GOOD_APIC=y +CONFIG_X86_WP_WORKS_OK=y CONFIG_X86_INTEL_USERCOPY=y CONFIG_X86_USE_PPRO_CHECKSUM=y CONFIG_X86_P6_NOP=y CONFIG_X86_TSC=y +CONFIG_X86_CMPXCHG64=y CONFIG_X86_CMOV=y CONFIG_X86_MINIMUM_CPU_FAMILY=64 CONFIG_X86_DEBUGCTLMSR=y @@ -234,8 +240,10 @@ CONFIG_DMI=y CONFIG_GART_IOMMU=y CONFIG_CALGARY_IOMMU=y CONFIG_CALGARY_IOMMU_ENABLED_BY_DEFAULT=y +CONFIG_AMD_IOMMU=y CONFIG_SWIOTLB=y CONFIG_IOMMU_HELPER=y +# CONFIG_MAXSMP is not set CONFIG_NR_CPUS=4 # CONFIG_SCHED_SMT is not set CONFIG_SCHED_MC=y @@ -281,6 +289,7 @@ CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y CONFIG_MTRR=y +# CONFIG_MTRR_SANITIZER is not set # CONFIG_X86_PAT is not set CONFIG_EFI=y CONFIG_SECCOMP=y @@ -313,6 +322,7 @@ CONFIG_PM_TRACE_RTC=y CONFIG_PM_SLEEP_SMP=y CONFIG_PM_SLEEP=y CONFIG_SUSPEND=y +# CONFIG_PM_TEST_SUSPEND is not set CONFIG_SUSPEND_FREEZER=y CONFIG_HIBERNATION=y CONFIG_PM_STD_PARTITION="" @@ -339,6 +349,7 @@ CONFIG_ACPI_NUMA=y CONFIG_ACPI_BLACKLIST_YEAR=0 # CONFIG_ACPI_DEBUG is not set CONFIG_ACPI_EC=y +# CONFIG_ACPI_PCI_SLOT is not set CONFIG_ACPI_POWER=y CONFIG_ACPI_SYSTEM=y CONFIG_X86_PM_TIMER=y @@ -437,10 +448,6 @@ CONFIG_IA32_EMULATION=y CONFIG_COMPAT=y CONFIG_COMPAT_FOR_U64_ALIGNMENT=y CONFIG_SYSVIPC_COMPAT=y - -# -# Networking -# CONFIG_NET=y # @@ -464,7 +471,10 @@ CONFIG_IP_FIB_HASH=y CONFIG_IP_MULTIPLE_TABLES=y CONFIG_IP_ROUTE_MULTIPATH=y CONFIG_IP_ROUTE_VERBOSE=y -# CONFIG_IP_PNP is not set +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y # CONFIG_NET_IPIP is not set # CONFIG_NET_IPGRE is not set CONFIG_IP_MROUTE=y @@ -607,7 +617,6 @@ CONFIG_NET_SCHED=y # CONFIG_NET_SCH_HTB is not set # CONFIG_NET_SCH_HFSC is not set # CONFIG_NET_SCH_PRIO is not set -# CONFIG_NET_SCH_RR is not set # CONFIG_NET_SCH_RED is not set # CONFIG_NET_SCH_SFQ is not set # CONFIG_NET_SCH_TEQL is not set @@ -669,28 +678,19 @@ CONFIG_FIB_RULES=y CONFIG_CFG80211=y CONFIG_NL80211=y CONFIG_WIRELESS_EXT=y +CONFIG_WIRELESS_EXT_SYSFS=y CONFIG_MAC80211=y # # Rate control algorithm selection # +CONFIG_MAC80211_RC_PID=y CONFIG_MAC80211_RC_DEFAULT_PID=y -# CONFIG_MAC80211_RC_DEFAULT_NONE is not set - -# -# Selecting 'y' for an algorithm will -# - -# -# build the algorithm into mac80211. -# CONFIG_MAC80211_RC_DEFAULT="pid" -CONFIG_MAC80211_RC_PID=y # CONFIG_MAC80211_MESH is not set CONFIG_MAC80211_LEDS=y # CONFIG_MAC80211_DEBUGFS is not set -# CONFIG_MAC80211_DEBUG_PACKET_ALIGNMENT is not set -# CONFIG_MAC80211_DEBUG is not set +# CONFIG_MAC80211_DEBUG_MENU is not set # CONFIG_IEEE80211 is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -706,6 +706,8 @@ CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_EXTRA_FIRMWARE="" # CONFIG_DEBUG_DRIVER is not set CONFIG_DEBUG_DEVRES=y # CONFIG_SYS_HYPERVISOR is not set @@ -738,6 +740,7 @@ CONFIG_BLK_DEV_RAM_SIZE=16384 # CONFIG_BLK_DEV_XIP is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set +# CONFIG_BLK_DEV_HD is not set CONFIG_MISC_DEVICES=y # CONFIG_IBM_ASM is not set # CONFIG_PHANTOM is not set @@ -748,10 +751,14 @@ CONFIG_MISC_DEVICES=y # CONFIG_ASUS_LAPTOP is not set # CONFIG_FUJITSU_LAPTOP is not set # CONFIG_MSI_LAPTOP is not set +# CONFIG_COMPAL_LAPTOP is not set # CONFIG_SONY_LAPTOP is not set # CONFIG_THINKPAD_ACPI is not set # CONFIG_INTEL_MENLOW is not set # CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_SGI_XP is not set +# CONFIG_HP_ILO is not set +# CONFIG_SGI_GRU is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -790,12 +797,13 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_SPI_ATTRS=y # CONFIG_SCSI_FC_ATTRS is not set -# CONFIG_SCSI_ISCSI_ATTRS is not set +CONFIG_SCSI_ISCSI_ATTRS=y # CONFIG_SCSI_SAS_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set # CONFIG_SCSI_SRP_ATTRS is not set # CONFIG_SCSI_LOWLEVEL is not set # CONFIG_SCSI_LOWLEVEL_PCMCIA is not set +# CONFIG_SCSI_DH is not set CONFIG_ATA=y # CONFIG_ATA_NONSTANDARD is not set CONFIG_ATA_ACPI=y @@ -857,6 +865,7 @@ CONFIG_PATA_OLDPIIX=y # CONFIG_PATA_SIS is not set # CONFIG_PATA_VIA is not set # CONFIG_PATA_WINBOND is not set +CONFIG_PATA_SCH=y CONFIG_MD=y CONFIG_BLK_DEV_MD=y # CONFIG_MD_LINEAR is not set @@ -880,13 +889,16 @@ CONFIG_DM_ZERO=y # # IEEE 1394 (FireWire) support # + +# +# Enable only one of the two stacks, unless you know what you are doing +# # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set CONFIG_MACINTOSH_DRIVERS=y CONFIG_MAC_EMUMOUSEBTN=y CONFIG_NETDEVICES=y -# CONFIG_NETDEVICES_MULTIQUEUE is not set # CONFIG_IFB is not set # CONFIG_DUMMY is not set # CONFIG_BONDING is not set @@ -896,7 +908,23 @@ CONFIG_NETDEVICES=y # CONFIG_VETH is not set # CONFIG_NET_SB1000 is not set # CONFIG_ARCNET is not set -# CONFIG_PHYLIB is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_REALTEK_PHY is not set +# CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -940,16 +968,15 @@ CONFIG_8139TOO_PIO=y # CONFIG_SIS900 is not set # CONFIG_EPIC100 is not set # CONFIG_SUNDANCE is not set +# CONFIG_TLAN is not set # CONFIG_VIA_RHINE is not set # CONFIG_SC92031 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set CONFIG_E1000=y -# CONFIG_E1000_NAPI is not set # CONFIG_E1000_DISABLE_PACKET_SPLIT is not set # CONFIG_E1000E is not set -# CONFIG_E1000E_ENABLED is not set # CONFIG_IP1000 is not set # CONFIG_IGB is not set # CONFIG_NS83820 is not set @@ -965,6 +992,7 @@ CONFIG_TIGON3=y # CONFIG_BNX2 is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set +# CONFIG_ATL1E is not set CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set @@ -1003,13 +1031,14 @@ CONFIG_WLAN_80211=y # CONFIG_RTL8180 is not set # CONFIG_RTL8187 is not set # CONFIG_ADM8211 is not set +# CONFIG_MAC80211_HWSIM is not set # CONFIG_P54_COMMON is not set CONFIG_ATH5K=y # CONFIG_ATH5K_DEBUG is not set -# CONFIG_IWLWIFI is not set +# CONFIG_ATH9K is not set # CONFIG_IWLCORE is not set # CONFIG_IWLWIFI_LEDS is not set -# CONFIG_IWL4965 is not set +# CONFIG_IWLAGN is not set # CONFIG_IWL3945 is not set # CONFIG_HOSTAP is not set # CONFIG_B43 is not set @@ -1088,6 +1117,7 @@ CONFIG_MOUSE_PS2_TRACKPOINT=y # CONFIG_MOUSE_PS2_TOUCHKIT is not set # CONFIG_MOUSE_SERIAL is not set # CONFIG_MOUSE_APPLETOUCH is not set +# CONFIG_MOUSE_BCM5974 is not set # CONFIG_MOUSE_VSXXXAA is not set CONFIG_INPUT_JOYSTICK=y # CONFIG_JOYSTICK_ANALOG is not set @@ -1122,12 +1152,14 @@ CONFIG_INPUT_TOUCHSCREEN=y # CONFIG_TOUCHSCREEN_GUNZE is not set # CONFIG_TOUCHSCREEN_ELO is not set # CONFIG_TOUCHSCREEN_MTOUCH is not set +# CONFIG_TOUCHSCREEN_INEXIO is not set # CONFIG_TOUCHSCREEN_MK712 is not set # CONFIG_TOUCHSCREEN_PENMOUNT is not set # CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set # CONFIG_TOUCHSCREEN_TOUCHWIN is not set # CONFIG_TOUCHSCREEN_UCB1400 is not set # CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set +# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set CONFIG_INPUT_MISC=y # CONFIG_INPUT_PCSPKR is not set # CONFIG_INPUT_APANEL is not set @@ -1155,6 +1187,7 @@ CONFIG_SERIO_LIBPS2=y # Character devices # CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y CONFIG_VT_HW_CONSOLE_BINDING=y @@ -1222,7 +1255,6 @@ CONFIG_NVRAM=y # CONFIG_PC8736x_GPIO is not set # CONFIG_RAW_DRIVER is not set CONFIG_HPET=y -# CONFIG_HPET_RTC_IRQ is not set # CONFIG_HPET_MMAP is not set # CONFIG_HANGCHECK_TIMER is not set # CONFIG_TCG_TPM is not set @@ -1231,42 +1263,63 @@ CONFIG_DEVPORT=y CONFIG_I2C=y CONFIG_I2C_BOARDINFO=y # CONFIG_I2C_CHARDEV is not set +CONFIG_I2C_HELPER_AUTO=y # # I2C Hardware Bus support # + +# +# PC SMBus host controller drivers +# # CONFIG_I2C_ALI1535 is not set # CONFIG_I2C_ALI1563 is not set # CONFIG_I2C_ALI15X3 is not set # CONFIG_I2C_AMD756 is not set # CONFIG_I2C_AMD8111 is not set CONFIG_I2C_I801=y -# CONFIG_I2C_I810 is not set +# CONFIG_I2C_ISCH is not set # CONFIG_I2C_PIIX4 is not set # CONFIG_I2C_NFORCE2 is not set -# CONFIG_I2C_OCORES is not set -# CONFIG_I2C_PARPORT_LIGHT is not set -# CONFIG_I2C_PROSAVAGE is not set -# CONFIG_I2C_SAVAGE4 is not set -# CONFIG_I2C_SIMTEC is not set # CONFIG_I2C_SIS5595 is not set # CONFIG_I2C_SIS630 is not set # CONFIG_I2C_SIS96X is not set -# CONFIG_I2C_TAOS_EVM is not set -# CONFIG_I2C_STUB is not set -# CONFIG_I2C_TINY_USB is not set # CONFIG_I2C_VIA is not set # CONFIG_I2C_VIAPRO is not set + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_TINY_USB is not set + +# +# Graphics adapter I2C/DDC channel drivers +# # CONFIG_I2C_VOODOO3 is not set + +# +# Other I2C/SMBus bus drivers +# # CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set # # Miscellaneous I2C Chip support # # CONFIG_DS1682 is not set +# CONFIG_AT24 is not set # CONFIG_SENSORS_EEPROM is not set # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set # CONFIG_SENSORS_PCF8591 is not set # CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set @@ -1275,6 +1328,8 @@ CONFIG_I2C_I801=y # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set +CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y +# CONFIG_GPIOLIB is not set # CONFIG_W1 is not set CONFIG_POWER_SUPPLY=y # CONFIG_POWER_SUPPLY_DEBUG is not set @@ -1335,8 +1390,10 @@ CONFIG_SSB_POSSIBLE=y # # Multifunction device drivers # +# CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set # # Multimedia devices @@ -1347,6 +1404,7 @@ CONFIG_SSB_POSSIBLE=y # # CONFIG_VIDEO_DEV is not set # CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set # # Multimedia drivers @@ -1387,7 +1445,6 @@ CONFIG_FB_CFB_IMAGEBLIT=y # CONFIG_FB_SYS_IMAGEBLIT is not set # CONFIG_FB_FOREIGN_ENDIAN is not set # CONFIG_FB_SYS_FOPS is not set -CONFIG_FB_DEFERRED_IO=y # CONFIG_FB_SVGALIB is not set # CONFIG_FB_MACMODES is not set # CONFIG_FB_BACKLIGHT is not set @@ -1430,6 +1487,7 @@ CONFIG_FB_EFI=y # CONFIG_FB_TRIDENT is not set # CONFIG_FB_ARK is not set # CONFIG_FB_PM3 is not set +# CONFIG_FB_CARMINE is not set # CONFIG_FB_GEODE is not set # CONFIG_FB_VIRTUAL is not set CONFIG_BACKLIGHT_LCD_SUPPORT=y @@ -1437,6 +1495,7 @@ CONFIG_BACKLIGHT_LCD_SUPPORT=y CONFIG_BACKLIGHT_CLASS_DEVICE=y # CONFIG_BACKLIGHT_CORGI is not set # CONFIG_BACKLIGHT_PROGEAR is not set +# CONFIG_BACKLIGHT_MBP_NVIDIA is not set # # Display device support @@ -1456,15 +1515,7 @@ CONFIG_LOGO=y # CONFIG_LOGO_LINUX_MONO is not set # CONFIG_LOGO_LINUX_VGA16 is not set CONFIG_LOGO_LINUX_CLUT224=y - -# -# Sound -# CONFIG_SOUND=y - -# -# Advanced Linux Sound Architecture -# CONFIG_SND=y CONFIG_SND_TIMER=y CONFIG_SND_PCM=y @@ -1482,20 +1533,14 @@ CONFIG_SND_VERBOSE_PROCFS=y # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set CONFIG_SND_VMASTER=y - -# -# Generic devices -# +CONFIG_SND_DRIVERS=y # CONFIG_SND_PCSP is not set # CONFIG_SND_DUMMY is not set # CONFIG_SND_VIRMIDI is not set # CONFIG_SND_MTPAV is not set # CONFIG_SND_SERIAL_U16550 is not set # CONFIG_SND_MPU401 is not set - -# -# PCI devices -# +CONFIG_SND_PCI=y # CONFIG_SND_AD1889 is not set # CONFIG_SND_ALS300 is not set # CONFIG_SND_ALS4000 is not set @@ -1568,36 +1613,14 @@ CONFIG_SND_HDA_GENERIC=y # CONFIG_SND_VIRTUOSO is not set # CONFIG_SND_VX222 is not set # CONFIG_SND_YMFPCI is not set - -# -# USB devices -# +CONFIG_SND_USB=y # CONFIG_SND_USB_AUDIO is not set # CONFIG_SND_USB_USX2Y is not set # CONFIG_SND_USB_CAIAQ is not set - -# -# PCMCIA devices -# +CONFIG_SND_PCMCIA=y # CONFIG_SND_VXPOCKET is not set # CONFIG_SND_PDAUDIOCF is not set - -# -# System on Chip audio support -# # CONFIG_SND_SOC is not set - -# -# ALSA SoC audio for Freescale SOCs -# - -# -# SoC Audio for the Texas Instruments OMAP -# - -# -# Open Sound System -# # CONFIG_SOUND_PRIME is not set CONFIG_HID_SUPPORT=y CONFIG_HID=y @@ -1633,6 +1656,7 @@ CONFIG_USB_DEVICEFS=y # CONFIG_USB_DYNAMIC_MINORS is not set CONFIG_USB_SUSPEND=y # CONFIG_USB_OTG is not set +CONFIG_USB_MON=y # # USB Host Controller Drivers @@ -1656,6 +1680,7 @@ CONFIG_USB_UHCI_HCD=y # # CONFIG_USB_ACM is not set CONFIG_USB_PRINTER=y +# CONFIG_USB_WDM is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -1677,6 +1702,7 @@ CONFIG_USB_STORAGE=y # CONFIG_USB_STORAGE_ALAUDA is not set # CONFIG_USB_STORAGE_ONETOUCH is not set # CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_SIERRA is not set # CONFIG_USB_STORAGE_CYPRESS_ATACB is not set CONFIG_USB_LIBUSUAL=y @@ -1685,7 +1711,6 @@ CONFIG_USB_LIBUSUAL=y # # CONFIG_USB_MDC800 is not set # CONFIG_USB_MICROTEK is not set -CONFIG_USB_MON=y # # USB port drivers @@ -1698,7 +1723,6 @@ CONFIG_USB_MON=y # CONFIG_USB_EMI62 is not set # CONFIG_USB_EMI26 is not set # CONFIG_USB_ADUTUX is not set -# CONFIG_USB_AUERSWALD is not set # CONFIG_USB_RIO500 is not set # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set @@ -1715,6 +1739,7 @@ CONFIG_USB_MON=y # CONFIG_USB_TRANCEVIBRATOR is not set # CONFIG_USB_IOWARRIOR is not set # CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set # CONFIG_USB_GADGET is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set @@ -1724,7 +1749,9 @@ CONFIG_LEDS_CLASS=y # # LED drivers # +# CONFIG_LEDS_PCA9532 is not set # CONFIG_LEDS_CLEVO_MAIL is not set +# CONFIG_LEDS_PCA955X is not set # # LED Triggers @@ -1770,6 +1797,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_PCF8583 is not set # CONFIG_RTC_DRV_M41T80 is not set # CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set # # SPI RTC drivers @@ -1802,11 +1830,13 @@ CONFIG_DMADEVICES=y # Firmware Drivers # # CONFIG_EDD is not set +CONFIG_FIRMWARE_MEMMAP=y CONFIG_EFI_VARS=y # CONFIG_DELL_RBU is not set # CONFIG_DCDBAS is not set CONFIG_DMIID=y -# CONFIG_ISCSI_IBFT_FIND is not set +CONFIG_ISCSI_IBFT_FIND=y +CONFIG_ISCSI_IBFT=y # # File systems @@ -1886,14 +1916,27 @@ CONFIG_HUGETLB_PAGE=y # CONFIG_CRAMFS is not set # CONFIG_VXFS_FS is not set # CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_ROMFS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set CONFIG_NETWORK_FILESYSTEMS=y -# CONFIG_NFS_FS is not set +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +CONFIG_NFS_V3_ACL=y +CONFIG_NFS_V4=y +CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_ACL_SUPPORT=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set # CONFIG_CIFS is not set # CONFIG_NCP_FS is not set @@ -1967,9 +2010,9 @@ CONFIG_NLS_UTF8=y # Kernel hacking # CONFIG_TRACE_IRQFLAGS_SUPPORT=y -# CONFIG_PRINTK_TIME is not set -# CONFIG_ENABLE_WARN_DEPRECATED is not set -# CONFIG_ENABLE_MUST_CHECK is not set +CONFIG_PRINTK_TIME=y +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y CONFIG_FRAME_WARN=2048 CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -1998,6 +2041,7 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_WRITECOUNT is not set +CONFIG_DEBUG_MEMORY_INIT=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set CONFIG_FRAME_POINTER=y @@ -2008,11 +2052,20 @@ CONFIG_FRAME_POINTER=y # CONFIG_LKDTM is not set # CONFIG_FAULT_INJECTION is not set # CONFIG_LATENCYTOP is not set +CONFIG_SYSCTL_SYSCALL_CHECK=y +CONFIG_HAVE_FTRACE=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +# CONFIG_FTRACE is not set +# CONFIG_IRQSOFF_TRACER is not set +# CONFIG_SYSPROF_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set CONFIG_PROVIDE_OHCI1394_DMA_INIT=y # CONFIG_SAMPLES is not set -# CONFIG_KGDB is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set # CONFIG_STRICT_DEVMEM is not set +CONFIG_X86_VERBOSE_BOOTUP=y CONFIG_EARLY_PRINTK=y CONFIG_DEBUG_STACKOVERFLOW=y CONFIG_DEBUG_STACK_USAGE=y @@ -2023,8 +2076,8 @@ CONFIG_DEBUG_RODATA=y # CONFIG_DIRECT_GBPAGES is not set # CONFIG_DEBUG_RODATA_TEST is not set CONFIG_DEBUG_NX_TEST=m -CONFIG_X86_MPPARSE=y # CONFIG_IOMMU_DEBUG is not set +# CONFIG_MMIOTRACE is not set CONFIG_IO_DELAY_TYPE_0X80=0 CONFIG_IO_DELAY_TYPE_0XED=1 CONFIG_IO_DELAY_TYPE_UDELAY=2 @@ -2036,6 +2089,7 @@ CONFIG_IO_DELAY_0X80=y CONFIG_DEFAULT_IO_DELAY_TYPE=0 CONFIG_DEBUG_BOOT_PARAMS=y # CONFIG_CPA_DEBUG is not set +# CONFIG_OPTIMIZE_INLINING is not set # # Security options @@ -2045,7 +2099,6 @@ CONFIG_KEYS_DEBUG_PROC_KEYS=y CONFIG_SECURITY=y CONFIG_SECURITY_NETWORK=y # CONFIG_SECURITY_NETWORK_XFRM is not set -CONFIG_SECURITY_CAPABILITIES=y CONFIG_SECURITY_FILE_CAPABILITIES=y # CONFIG_SECURITY_ROOTPLUG is not set CONFIG_SECURITY_DEFAULT_MMAP_MIN_ADDR=65536 @@ -2106,6 +2159,10 @@ CONFIG_CRYPTO_HMAC=y # CONFIG_CRYPTO_MD4 is not set CONFIG_CRYPTO_MD5=y # CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set CONFIG_CRYPTO_SHA1=y # CONFIG_CRYPTO_SHA256 is not set # CONFIG_CRYPTO_SHA512 is not set @@ -2155,6 +2212,7 @@ CONFIG_GENERIC_FIND_FIRST_BIT=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_CRC_CCITT is not set # CONFIG_CRC16 is not set +CONFIG_CRC_T10DIF=y # CONFIG_CRC_ITU_T is not set CONFIG_CRC32=y # CONFIG_CRC7 is not set -- GitLab From 7414aa41a63348c3bc72d8c37b716024c29b6d50 Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Wed, 27 Aug 2008 17:56:44 -0700 Subject: [PATCH 747/750] x86: generate names for /proc/cpuinfo from We have had a number of cases where (and its predecessors) have diverged substantially from the names list in /proc/cpuinfo. This patch generates the latter from the former. It retains the option for explicitly overriding the strings, but by making that require a separate action it should at least be less likely to happen. It would be good to do a future pass and rename strings that are gratuituously different in the kernel (/proc/cpuinfo is a userspace interface and must remain constant.) Signed-off-by: H. Peter Anvin --- arch/x86/boot/mkcpustr.c | 2 +- arch/x86/kernel/cpu/Makefile | 11 +++- arch/x86/kernel/cpu/feature_names.c | 84 ---------------------------- arch/x86/kernel/cpu/mkcapflags.pl | 32 +++++++++++ arch/x86/kernel/cpu/powerflags.c | 20 +++++++ include/asm-x86/cpufeature.h | 86 ++++++++++++++++++----------- 6 files changed, 117 insertions(+), 118 deletions(-) delete mode 100644 arch/x86/kernel/cpu/feature_names.c create mode 100644 arch/x86/kernel/cpu/mkcapflags.pl create mode 100644 arch/x86/kernel/cpu/powerflags.c diff --git a/arch/x86/boot/mkcpustr.c b/arch/x86/boot/mkcpustr.c index bbe76953bae..4589caa3e9d 100644 --- a/arch/x86/boot/mkcpustr.c +++ b/arch/x86/boot/mkcpustr.c @@ -15,7 +15,7 @@ #include -#include "../kernel/cpu/feature_names.c" +#include "../kernel/cpu/capflags.c" #if NCAPFLAGS > 8 # error "Need to adjust the boot code handling of CPUID strings" diff --git a/arch/x86/kernel/cpu/Makefile b/arch/x86/kernel/cpu/Makefile index a0fc6c14438..3ede19a4e0b 100644 --- a/arch/x86/kernel/cpu/Makefile +++ b/arch/x86/kernel/cpu/Makefile @@ -3,7 +3,7 @@ # obj-y := intel_cacheinfo.o addon_cpuid_features.o -obj-y += proc.o feature_names.o +obj-y += proc.o capflags.o powerflags.o obj-$(CONFIG_X86_32) += common.o bugs.o cmpxchg.o obj-$(CONFIG_X86_64) += common_64.o bugs_64.o @@ -23,3 +23,12 @@ obj-$(CONFIG_MTRR) += mtrr/ obj-$(CONFIG_CPU_FREQ) += cpufreq/ obj-$(CONFIG_X86_LOCAL_APIC) += perfctr-watchdog.o + +quiet_cmd_mkcapflags = MKCAP $@ + cmd_mkcapflags = $(PERL) $(srctree)/$(src)/mkcapflags.pl $< $@ + +cpufeature = $(src)/../../../../include/asm-x86/cpufeature.h + +targets += capflags.c +$(obj)/capflags.c: $(cpufeature) $(src)/mkcapflags.pl FORCE + $(call if_changed,mkcapflags) diff --git a/arch/x86/kernel/cpu/feature_names.c b/arch/x86/kernel/cpu/feature_names.c deleted file mode 100644 index c9017799497..00000000000 --- a/arch/x86/kernel/cpu/feature_names.c +++ /dev/null @@ -1,84 +0,0 @@ -/* - * Strings for the various x86 capability flags. - * - * This file must not contain any executable code. - */ - -#include - -/* - * These flag bits must match the definitions in . - * NULL means this bit is undefined or reserved; either way it doesn't - * have meaning as far as Linux is concerned. Note that it's important - * to realize there is a difference between this table and CPUID -- if - * applications want to get the raw CPUID data, they should access - * /dev/cpu//cpuid instead. - */ -const char * const x86_cap_flags[NCAPINTS*32] = { - /* Intel-defined */ - "fpu", "vme", "de", "pse", "tsc", "msr", "pae", "mce", - "cx8", "apic", NULL, "sep", "mtrr", "pge", "mca", "cmov", - "pat", "pse36", "pn", "clflush", NULL, "dts", "acpi", "mmx", - "fxsr", "sse", "sse2", "ss", "ht", "tm", "ia64", "pbe", - - /* AMD-defined */ - NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, - NULL, NULL, NULL, "syscall", NULL, NULL, NULL, NULL, - NULL, NULL, NULL, "mp", "nx", NULL, "mmxext", NULL, - NULL, "fxsr_opt", "pdpe1gb", "rdtscp", NULL, "lm", - "3dnowext", "3dnow", - - /* Transmeta-defined */ - "recovery", "longrun", NULL, "lrti", NULL, NULL, NULL, NULL, - NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, - NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, - NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, - - /* Other (Linux-defined) */ - "cxmmx", "k6_mtrr", "cyrix_arr", "centaur_mcr", - NULL, NULL, NULL, NULL, - "constant_tsc", "up", NULL, "arch_perfmon", - "pebs", "bts", NULL, NULL, - "rep_good", NULL, NULL, NULL, - "nopl", NULL, NULL, NULL, - NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, - - /* Intel-defined (#2) */ - "pni", NULL, NULL, "monitor", "ds_cpl", "vmx", "smx", "est", - "tm2", "ssse3", "cid", NULL, NULL, "cx16", "xtpr", NULL, - NULL, NULL, "dca", "sse4_1", "sse4_2", NULL, NULL, "popcnt", - NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, - - /* VIA/Cyrix/Centaur-defined */ - NULL, NULL, "rng", "rng_en", NULL, NULL, "ace", "ace_en", - "ace2", "ace2_en", "phe", "phe_en", "pmm", "pmm_en", NULL, NULL, - NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, - NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, - - /* AMD-defined (#2) */ - "lahf_lm", "cmp_legacy", "svm", "extapic", - "cr8_legacy", "abm", "sse4a", "misalignsse", - "3dnowprefetch", "osvw", "ibs", "sse5", - "skinit", "wdt", NULL, NULL, - NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, - NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, - - /* Auxiliary (Linux-defined) */ - "ida", NULL, NULL, NULL, NULL, NULL, NULL, NULL, - NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, - NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, - NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, -}; - -const char *const x86_power_flags[32] = { - "ts", /* temperature sensor */ - "fid", /* frequency id control */ - "vid", /* voltage id control */ - "ttp", /* thermal trip */ - "tm", - "stc", - "100mhzsteps", - "hwpstate", - "", /* tsc invariant mapped to constant_tsc */ - /* nothing */ -}; diff --git a/arch/x86/kernel/cpu/mkcapflags.pl b/arch/x86/kernel/cpu/mkcapflags.pl new file mode 100644 index 00000000000..dfea390e160 --- /dev/null +++ b/arch/x86/kernel/cpu/mkcapflags.pl @@ -0,0 +1,32 @@ +#!/usr/bin/perl +# +# Generate the x86_cap_flags[] array from include/asm-x86/cpufeature.h +# + +($in, $out) = @ARGV; + +open(IN, "< $in\0") or die "$0: cannot open: $in: $!\n"; +open(OUT, "> $out\0") or die "$0: cannot create: $out: $!\n"; + +print OUT "#include \n\n"; +print OUT "const char * const x86_cap_flags[NCAPINTS*32] = {\n"; + +while (defined($line = )) { + if ($line =~ /^\s*\#\s*define\s+(X86_FEATURE_(\S+))\s+(.*)$/) { + $macro = $1; + $feature = $2; + $tail = $3; + if ($tail =~ /\/\*\s*\"([^"]*)\".*\*\//) { + $feature = $1; + } + + if ($feature ne '') { + printf OUT "\t%-32s = \"%s\",\n", + "[$macro]", "\L$feature"; + } + } +} +print OUT "};\n"; + +close(IN); +close(OUT); diff --git a/arch/x86/kernel/cpu/powerflags.c b/arch/x86/kernel/cpu/powerflags.c new file mode 100644 index 00000000000..5abbea297e0 --- /dev/null +++ b/arch/x86/kernel/cpu/powerflags.c @@ -0,0 +1,20 @@ +/* + * Strings for the various x86 power flags + * + * This file must not contain any executable code. + */ + +#include + +const char *const x86_power_flags[32] = { + "ts", /* temperature sensor */ + "fid", /* frequency id control */ + "vid", /* voltage id control */ + "ttp", /* thermal trip */ + "tm", + "stc", + "100mhzsteps", + "hwpstate", + "", /* tsc invariant mapped to constant_tsc */ + /* nothing */ +}; diff --git a/include/asm-x86/cpufeature.h b/include/asm-x86/cpufeature.h index 9489283a4bc..611da2898b2 100644 --- a/include/asm-x86/cpufeature.h +++ b/include/asm-x86/cpufeature.h @@ -8,6 +8,12 @@ #define NCAPINTS 8 /* N 32-bit words worth of info */ +/* + * Note: If the comment begins with a quoted string, that string is used + * in /proc/cpuinfo instead of the macro name. If the string is "", + * this feature bit is not displayed in /proc/cpuinfo at all. + */ + /* Intel-defined CPU features, CPUID level 0x00000001 (edx), word 0 */ #define X86_FEATURE_FPU (0*32+ 0) /* Onboard FPU */ #define X86_FEATURE_VME (0*32+ 1) /* Virtual Mode Extensions */ @@ -27,18 +33,18 @@ #define X86_FEATURE_PAT (0*32+16) /* Page Attribute Table */ #define X86_FEATURE_PSE36 (0*32+17) /* 36-bit PSEs */ #define X86_FEATURE_PN (0*32+18) /* Processor serial number */ -#define X86_FEATURE_CLFLSH (0*32+19) /* Supports the CLFLUSH instruction */ -#define X86_FEATURE_DS (0*32+21) /* Debug Store */ +#define X86_FEATURE_CLFLSH (0*32+19) /* "clflush" Supports the CLFLUSH instruction */ +#define X86_FEATURE_DS (0*32+21) /* "dts" Debug Store */ #define X86_FEATURE_ACPI (0*32+22) /* ACPI via MSR */ #define X86_FEATURE_MMX (0*32+23) /* Multimedia Extensions */ -#define X86_FEATURE_FXSR (0*32+24) /* FXSAVE and FXRSTOR instructions (fast save and restore */ - /* of FPU context), and CR4.OSFXSR available */ -#define X86_FEATURE_XMM (0*32+25) /* Streaming SIMD Extensions */ -#define X86_FEATURE_XMM2 (0*32+26) /* Streaming SIMD Extensions-2 */ -#define X86_FEATURE_SELFSNOOP (0*32+27) /* CPU self snoop */ +#define X86_FEATURE_FXSR (0*32+24) /* FXSAVE/FXRSTOR, CR4.OSFXSR */ +#define X86_FEATURE_XMM (0*32+25) /* "sse" */ +#define X86_FEATURE_XMM2 (0*32+26) /* "sse2" */ +#define X86_FEATURE_SELFSNOOP (0*32+27) /* "ss" CPU self snoop */ #define X86_FEATURE_HT (0*32+28) /* Hyper-Threading */ -#define X86_FEATURE_ACC (0*32+29) /* Automatic clock control */ +#define X86_FEATURE_ACC (0*32+29) /* "tm" Automatic clock control */ #define X86_FEATURE_IA64 (0*32+30) /* IA-64 processor */ +#define X86_FEATURE_PBE (0*32+31) /* Pending Break Enable */ /* AMD-defined CPU features, CPUID level 0x80000001, word 1 */ /* Don't duplicate feature flags which are redundant with Intel! */ @@ -46,7 +52,8 @@ #define X86_FEATURE_MP (1*32+19) /* MP Capable. */ #define X86_FEATURE_NX (1*32+20) /* Execute Disable */ #define X86_FEATURE_MMXEXT (1*32+22) /* AMD MMX extensions */ -#define X86_FEATURE_GBPAGES (1*32+26) /* GB pages */ +#define X86_FEATURE_FXSR_OPT (1*32+25) /* FXSAVE/FXRSTOR optimizations */ +#define X86_FEATURE_GBPAGES (1*32+26) /* "pdpe1gb" GB pages */ #define X86_FEATURE_RDTSCP (1*32+27) /* RDTSCP */ #define X86_FEATURE_LM (1*32+29) /* Long Mode (x86-64) */ #define X86_FEATURE_3DNOWEXT (1*32+30) /* AMD 3DNow! extensions */ @@ -64,52 +71,67 @@ #define X86_FEATURE_CYRIX_ARR (3*32+ 2) /* Cyrix ARRs (= MTRRs) */ #define X86_FEATURE_CENTAUR_MCR (3*32+ 3) /* Centaur MCRs (= MTRRs) */ /* cpu types for specific tunings: */ -#define X86_FEATURE_K8 (3*32+ 4) /* Opteron, Athlon64 */ -#define X86_FEATURE_K7 (3*32+ 5) /* Athlon */ -#define X86_FEATURE_P3 (3*32+ 6) /* P3 */ -#define X86_FEATURE_P4 (3*32+ 7) /* P4 */ +#define X86_FEATURE_K8 (3*32+ 4) /* "" Opteron, Athlon64 */ +#define X86_FEATURE_K7 (3*32+ 5) /* "" Athlon */ +#define X86_FEATURE_P3 (3*32+ 6) /* "" P3 */ +#define X86_FEATURE_P4 (3*32+ 7) /* "" P4 */ #define X86_FEATURE_CONSTANT_TSC (3*32+ 8) /* TSC ticks at a constant rate */ #define X86_FEATURE_UP (3*32+ 9) /* smp kernel running on up */ -#define X86_FEATURE_FXSAVE_LEAK (3*32+10) /* FXSAVE leaks FOP/FIP/FOP */ +#define X86_FEATURE_FXSAVE_LEAK (3*32+10) /* "" FXSAVE leaks FOP/FIP/FOP */ #define X86_FEATURE_ARCH_PERFMON (3*32+11) /* Intel Architectural PerfMon */ #define X86_FEATURE_PEBS (3*32+12) /* Precise-Event Based Sampling */ #define X86_FEATURE_BTS (3*32+13) /* Branch Trace Store */ -#define X86_FEATURE_SYSCALL32 (3*32+14) /* syscall in ia32 userspace */ -#define X86_FEATURE_SYSENTER32 (3*32+15) /* sysenter in ia32 userspace */ +#define X86_FEATURE_SYSCALL32 (3*32+14) /* "" syscall in ia32 userspace */ +#define X86_FEATURE_SYSENTER32 (3*32+15) /* "" sysenter in ia32 userspace */ #define X86_FEATURE_REP_GOOD (3*32+16) /* rep microcode works well on this CPU */ -#define X86_FEATURE_MFENCE_RDTSC (3*32+17) /* Mfence synchronizes RDTSC */ -#define X86_FEATURE_LFENCE_RDTSC (3*32+18) /* Lfence synchronizes RDTSC */ -#define X86_FEATURE_11AP (3*32+19) /* Bad local APIC aka 11AP */ +#define X86_FEATURE_MFENCE_RDTSC (3*32+17) /* "" Mfence synchronizes RDTSC */ +#define X86_FEATURE_LFENCE_RDTSC (3*32+18) /* "" Lfence synchronizes RDTSC */ +#define X86_FEATURE_11AP (3*32+19) /* "" Bad local APIC aka 11AP */ #define X86_FEATURE_NOPL (3*32+20) /* The NOPL (0F 1F) instructions */ /* Intel-defined CPU features, CPUID level 0x00000001 (ecx), word 4 */ -#define X86_FEATURE_XMM3 (4*32+ 0) /* Streaming SIMD Extensions-3 */ -#define X86_FEATURE_MWAIT (4*32+ 3) /* Monitor/Mwait support */ -#define X86_FEATURE_DSCPL (4*32+ 4) /* CPL Qualified Debug Store */ +#define X86_FEATURE_XMM3 (4*32+ 0) /* "pni" SSE-3 */ +#define X86_FEATURE_MWAIT (4*32+ 3) /* "monitor" Monitor/Mwait support */ +#define X86_FEATURE_DSCPL (4*32+ 4) /* "ds_cpl" CPL Qual. Debug Store */ +#define X86_FEATURE_VMX (4*32+ 5) /* Hardware virtualization */ +#define X86_FEATURE_SMX (4*32+ 6) /* "Safer" mode */ #define X86_FEATURE_EST (4*32+ 7) /* Enhanced SpeedStep */ #define X86_FEATURE_TM2 (4*32+ 8) /* Thermal Monitor 2 */ +#define X86_FEATURE_SSSE3 (4*32+ 9) /* Supplemental SSE-3 */ #define X86_FEATURE_CID (4*32+10) /* Context ID */ #define X86_FEATURE_CX16 (4*32+13) /* CMPXCHG16B */ #define X86_FEATURE_XTPR (4*32+14) /* Send Task Priority Messages */ #define X86_FEATURE_DCA (4*32+18) /* Direct Cache Access */ -#define X86_FEATURE_XMM4_2 (4*32+20) /* Streaming SIMD Extensions-4.2 */ +#define X86_FEATURE_XMM4_1 (4*32+19) /* "sse4_1" SSE-4.1 */ +#define X86_FEATURE_XMM4_2 (4*32+20) /* "sse4_2" SSE-4.2 */ /* VIA/Cyrix/Centaur-defined CPU features, CPUID level 0xC0000001, word 5 */ -#define X86_FEATURE_XSTORE (5*32+ 2) /* on-CPU RNG present (xstore insn) */ -#define X86_FEATURE_XSTORE_EN (5*32+ 3) /* on-CPU RNG enabled */ -#define X86_FEATURE_XCRYPT (5*32+ 6) /* on-CPU crypto (xcrypt insn) */ -#define X86_FEATURE_XCRYPT_EN (5*32+ 7) /* on-CPU crypto enabled */ +#define X86_FEATURE_XSTORE (5*32+ 2) /* "rng" RNG present (xstore) */ +#define X86_FEATURE_XSTORE_EN (5*32+ 3) /* "rng_en" RNG enabled */ +#define X86_FEATURE_XCRYPT (5*32+ 6) /* "ace" on-CPU crypto (xcrypt) */ +#define X86_FEATURE_XCRYPT_EN (5*32+ 7) /* "ace_en" on-CPU crypto enabled */ #define X86_FEATURE_ACE2 (5*32+ 8) /* Advanced Cryptography Engine v2 */ #define X86_FEATURE_ACE2_EN (5*32+ 9) /* ACE v2 enabled */ -#define X86_FEATURE_PHE (5*32+ 10) /* PadLock Hash Engine */ -#define X86_FEATURE_PHE_EN (5*32+ 11) /* PHE enabled */ -#define X86_FEATURE_PMM (5*32+ 12) /* PadLock Montgomery Multiplier */ -#define X86_FEATURE_PMM_EN (5*32+ 13) /* PMM enabled */ +#define X86_FEATURE_PHE (5*32+10) /* PadLock Hash Engine */ +#define X86_FEATURE_PHE_EN (5*32+11) /* PHE enabled */ +#define X86_FEATURE_PMM (5*32+12) /* PadLock Montgomery Multiplier */ +#define X86_FEATURE_PMM_EN (5*32+13) /* PMM enabled */ /* More extended AMD flags: CPUID level 0x80000001, ecx, word 6 */ #define X86_FEATURE_LAHF_LM (6*32+ 0) /* LAHF/SAHF in long mode */ #define X86_FEATURE_CMP_LEGACY (6*32+ 1) /* If yes HyperThreading not valid */ -#define X86_FEATURE_IBS (6*32+ 10) /* Instruction Based Sampling */ +#define X86_FEATURE_SVM (6*32+ 2) /* Secure virtual machine */ +#define X86_FEATURE_EXTAPIC (6*32+ 3) /* Extended APIC space */ +#define X86_FEATURE_CR8_LEGACY (6*32+ 4) /* CR8 in 32-bit mode */ +#define X86_FEATURE_ABM (6*32+ 5) /* Advanced bit manipulation */ +#define X86_FEATURE_SSE4A (6*32+ 6) /* SSE-4A */ +#define X86_FEATURE_MISALIGNSSE (6*32+ 7) /* Misaligned SSE mode */ +#define X86_FEATURE_3DNOWPREFETCH (6*32+ 8) /* 3DNow prefetch instructions */ +#define X86_FEATURE_OSVW (6*32+ 9) /* OS Visible Workaround */ +#define X86_FEATURE_IBS (6*32+10) /* Instruction Based Sampling */ +#define X86_FEATURE_SSE5 (6*32+11) /* SSE-5 */ +#define X86_FEATURE_SKINIT (6*32+12) /* SKINIT/STGI instructions */ +#define X86_FEATURE_WDT (6*32+13) /* Watchdog timer */ /* * Auxiliary flags: Linux defined - For features scattered in various -- GitLab From f1240c002679a77990fd7c198991ed15a437d691 Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Wed, 27 Aug 2008 18:53:07 -0700 Subject: [PATCH 748/750] x86: cpufeature: add Intel features from CPUID and AVX specs Add all Intel CPUID features currently documented in the CPUID spec (AP-485, 241618-032, Dec 2007) and the AVX Programming Reference (319433-003, Aug 2008). Signed-off-by: H. Peter Anvin --- include/asm-x86/cpufeature.h | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/include/asm-x86/cpufeature.h b/include/asm-x86/cpufeature.h index 611da2898b2..7bd98b724fd 100644 --- a/include/asm-x86/cpufeature.h +++ b/include/asm-x86/cpufeature.h @@ -91,6 +91,8 @@ /* Intel-defined CPU features, CPUID level 0x00000001 (ecx), word 4 */ #define X86_FEATURE_XMM3 (4*32+ 0) /* "pni" SSE-3 */ +#define X86_FEATURE_PCLMULQDQ (4*32+ 1) /* PCLMULQDQ instruction */ +#define X86_FEATURE_DTES64 (4*32+ 2) /* 64-bit Debug Store */ #define X86_FEATURE_MWAIT (4*32+ 3) /* "monitor" Monitor/Mwait support */ #define X86_FEATURE_DSCPL (4*32+ 4) /* "ds_cpl" CPL Qual. Debug Store */ #define X86_FEATURE_VMX (4*32+ 5) /* Hardware virtualization */ @@ -99,11 +101,18 @@ #define X86_FEATURE_TM2 (4*32+ 8) /* Thermal Monitor 2 */ #define X86_FEATURE_SSSE3 (4*32+ 9) /* Supplemental SSE-3 */ #define X86_FEATURE_CID (4*32+10) /* Context ID */ +#define X86_FEATURE_FMA (4*32+12) /* Fused multiply-add */ #define X86_FEATURE_CX16 (4*32+13) /* CMPXCHG16B */ #define X86_FEATURE_XTPR (4*32+14) /* Send Task Priority Messages */ +#define X86_FEATURE_PDCM (4*32+15) /* Performance Capabilities */ #define X86_FEATURE_DCA (4*32+18) /* Direct Cache Access */ #define X86_FEATURE_XMM4_1 (4*32+19) /* "sse4_1" SSE-4.1 */ #define X86_FEATURE_XMM4_2 (4*32+20) /* "sse4_2" SSE-4.2 */ +#define X86_FEATURE_X2APIC (4*32+21) /* x2APIC */ +#define X86_FEATURE_AES (4*32+25) /* AES instructions */ +#define X86_FEATURE_XSAVE (4*32+26) /* XSAVE/XRSTOR/XSETBV/XGETBV */ +#define X86_FEATURE_OSXSAVE (4*32+27) /* "" XSAVE enabled in the OS */ +#define X86_FEATURE_AVX (4*32+28) /* Advanced Vector Extensions */ /* VIA/Cyrix/Centaur-defined CPU features, CPUID level 0xC0000001, word 5 */ #define X86_FEATURE_XSTORE (5*32+ 2) /* "rng" RNG present (xstore) */ @@ -213,7 +222,10 @@ extern const char * const x86_power_flags[32]; #define cpu_has_gbpages boot_cpu_has(X86_FEATURE_GBPAGES) #define cpu_has_arch_perfmon boot_cpu_has(X86_FEATURE_ARCH_PERFMON) #define cpu_has_pat boot_cpu_has(X86_FEATURE_PAT) +#define cpu_has_xmm4_1 boot_cpu_has(X86_FEATURE_XMM4_1) #define cpu_has_xmm4_2 boot_cpu_has(X86_FEATURE_XMM4_2) +#define cpu_has_x2apic boot_cpu_has(X86_FEATURE_X2APIC) +#define cpu_has_xsave boot_cpu_has(X86_FEATURE_XSAVE) #if defined(CONFIG_X86_INVLPG) || defined(CONFIG_X86_64) # define cpu_has_invlpg 1 -- GitLab From 2798c63e65cb0f05cc12a060b9b0d56ac9523c4d Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Wed, 27 Aug 2008 21:20:07 -0700 Subject: [PATCH 749/750] x86: : clean up overlong lines, whitespace Clean up overlong lines and stealth whitespace in . Signed-off-by: H. Peter Anvin --- include/asm-x86/cpufeature.h | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-) diff --git a/include/asm-x86/cpufeature.h b/include/asm-x86/cpufeature.h index 7bd98b724fd..7710686c11f 100644 --- a/include/asm-x86/cpufeature.h +++ b/include/asm-x86/cpufeature.h @@ -20,7 +20,7 @@ #define X86_FEATURE_DE (0*32+ 2) /* Debugging Extensions */ #define X86_FEATURE_PSE (0*32+ 3) /* Page Size Extensions */ #define X86_FEATURE_TSC (0*32+ 4) /* Time Stamp Counter */ -#define X86_FEATURE_MSR (0*32+ 5) /* Model-Specific Registers, RDMSR, WRMSR */ +#define X86_FEATURE_MSR (0*32+ 5) /* Model-Specific Registers */ #define X86_FEATURE_PAE (0*32+ 6) /* Physical Address Extensions */ #define X86_FEATURE_MCE (0*32+ 7) /* Machine Check Architecture */ #define X86_FEATURE_CX8 (0*32+ 8) /* CMPXCHG8 instruction */ @@ -29,11 +29,12 @@ #define X86_FEATURE_MTRR (0*32+12) /* Memory Type Range Registers */ #define X86_FEATURE_PGE (0*32+13) /* Page Global Enable */ #define X86_FEATURE_MCA (0*32+14) /* Machine Check Architecture */ -#define X86_FEATURE_CMOV (0*32+15) /* CMOV instruction (FCMOVCC and FCOMI too if FPU present) */ +#define X86_FEATURE_CMOV (0*32+15) /* CMOV instructions */ + /* (plus FCMOVcc, FCOMI with FPU) */ #define X86_FEATURE_PAT (0*32+16) /* Page Attribute Table */ #define X86_FEATURE_PSE36 (0*32+17) /* 36-bit PSEs */ #define X86_FEATURE_PN (0*32+18) /* Processor serial number */ -#define X86_FEATURE_CLFLSH (0*32+19) /* "clflush" Supports the CLFLUSH instruction */ +#define X86_FEATURE_CLFLSH (0*32+19) /* "clflush" CLFLUSH instruction */ #define X86_FEATURE_DS (0*32+21) /* "dts" Debug Store */ #define X86_FEATURE_ACPI (0*32+22) /* ACPI via MSR */ #define X86_FEATURE_MMX (0*32+23) /* Multimedia Extensions */ @@ -83,7 +84,7 @@ #define X86_FEATURE_BTS (3*32+13) /* Branch Trace Store */ #define X86_FEATURE_SYSCALL32 (3*32+14) /* "" syscall in ia32 userspace */ #define X86_FEATURE_SYSENTER32 (3*32+15) /* "" sysenter in ia32 userspace */ -#define X86_FEATURE_REP_GOOD (3*32+16) /* rep microcode works well on this CPU */ +#define X86_FEATURE_REP_GOOD (3*32+16) /* rep microcode works well */ #define X86_FEATURE_MFENCE_RDTSC (3*32+17) /* "" Mfence synchronizes RDTSC */ #define X86_FEATURE_LFENCE_RDTSC (3*32+18) /* "" Lfence synchronizes RDTSC */ #define X86_FEATURE_11AP (3*32+19) /* "" Bad local APIC aka 11AP */ @@ -181,7 +182,7 @@ extern const char * const x86_power_flags[32]; } while (0) #define setup_force_cpu_cap(bit) do { \ set_cpu_cap(&boot_cpu_data, bit); \ - clear_bit(bit, (unsigned long *)cleared_cpu_caps); \ + clear_bit(bit, (unsigned long *)cleared_cpu_caps); \ } while (0) #define cpu_has_fpu boot_cpu_has(X86_FEATURE_FPU) -- GitLab From af2e1f276ff08f17192411ea3b71c13a758dfe12 Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Wed, 27 Aug 2008 22:05:45 -0700 Subject: [PATCH 750/750] x86: cpufeature: fix SMX flag Impact: "smx" flags showed as "safer" in /proc/cpuinfo The SMX feature flag is the so-called "safer mode"... I had put that in quotes, but that flagged it as a cpuinfo flag name. Remove the quotes to correct the flag name in /proc/cpuinfo. Signed-off-by: H. Peter Anvin --- include/asm-x86/cpufeature.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/asm-x86/cpufeature.h b/include/asm-x86/cpufeature.h index 7710686c11f..24d99d65741 100644 --- a/include/asm-x86/cpufeature.h +++ b/include/asm-x86/cpufeature.h @@ -97,7 +97,7 @@ #define X86_FEATURE_MWAIT (4*32+ 3) /* "monitor" Monitor/Mwait support */ #define X86_FEATURE_DSCPL (4*32+ 4) /* "ds_cpl" CPL Qual. Debug Store */ #define X86_FEATURE_VMX (4*32+ 5) /* Hardware virtualization */ -#define X86_FEATURE_SMX (4*32+ 6) /* "Safer" mode */ +#define X86_FEATURE_SMX (4*32+ 6) /* Safer mode */ #define X86_FEATURE_EST (4*32+ 7) /* Enhanced SpeedStep */ #define X86_FEATURE_TM2 (4*32+ 8) /* Thermal Monitor 2 */ #define X86_FEATURE_SSSE3 (4*32+ 9) /* Supplemental SSE-3 */ -- GitLab