diff --git a/CREDITS b/CREDITS index e97bea06b59ff12bc827c0661fb57974a6eff4d6..c62dcb3b7e2621d918815a656f2682fda044afcb 100644 --- a/CREDITS +++ b/CREDITS @@ -317,6 +317,14 @@ S: 2322 37th Ave SW S: Seattle, Washington 98126-2010 S: USA +N: Muli Ben-Yehuda +E: mulix@mulix.org +E: muli@il.ibm.com +W: http://www.mulix.org +D: trident OSS sound driver, x86-64 dma-ops and Calgary IOMMU, +D: KVM and Xen bits and other misc. hackery. +S: Haifa, Israel + N: Johannes Berg E: johannes@sipsolutions.net W: http://johannes.sipsolutions.net/ @@ -3344,8 +3352,7 @@ S: Spain N: Linus Torvalds E: torvalds@linux-foundation.org D: Original kernel hacker -S: 12725 SW Millikan Way, Suite 400 -S: Beaverton, Oregon 97005 +S: Portland, Oregon 97005 S: USA N: Marcelo Tosatti diff --git a/Documentation/00-INDEX b/Documentation/00-INDEX index 1977fab386566e23f501bea233f8f487d16f5c38..6de71308a9060b1a81c27aedb5b91042ff0b668b 100644 --- a/Documentation/00-INDEX +++ b/Documentation/00-INDEX @@ -361,8 +361,6 @@ telephony/ - directory with info on telephony (e.g. voice over IP) support. time_interpolators.txt - info on time interpolators. -tipar.txt - - information about Parallel link cable for Texas Instruments handhelds. tty.txt - guide to the locking policies of the tty layer. uml/ diff --git a/Documentation/ABI/testing/sysfs-dev b/Documentation/ABI/testing/sysfs-dev new file mode 100644 index 0000000000000000000000000000000000000000..a9f2b8b0530fb193be12ccfb7d0a529bf0ba435d --- /dev/null +++ b/Documentation/ABI/testing/sysfs-dev @@ -0,0 +1,20 @@ +What: /sys/dev +Date: April 2008 +KernelVersion: 2.6.26 +Contact: Dan Williams +Description: The /sys/dev tree provides a method to look up the sysfs + path for a device using the information returned from + stat(2). There are two directories, 'block' and 'char', + beneath /sys/dev containing symbolic links with names of + the form ":". These links point to the + corresponding sysfs path for the given device. + + Example: + $ readlink /sys/dev/block/8:32 + ../../block/sdc + + Entries in /sys/dev/char and /sys/dev/block will be + dynamically created and destroyed as devices enter and + leave the system. + +Users: mdadm diff --git a/Documentation/ABI/testing/sysfs-devices-memory b/Documentation/ABI/testing/sysfs-devices-memory new file mode 100644 index 0000000000000000000000000000000000000000..7a16fe1e2270d8e7353b209bd0dad24a5ce9b69e --- /dev/null +++ b/Documentation/ABI/testing/sysfs-devices-memory @@ -0,0 +1,24 @@ +What: /sys/devices/system/memory +Date: June 2008 +Contact: Badari Pulavarty +Description: + The /sys/devices/system/memory contains a snapshot of the + internal state of the kernel memory blocks. Files could be + added or removed dynamically to represent hot-add/remove + operations. + +Users: hotplug memory add/remove tools + https://w3.opensource.ibm.com/projects/powerpc-utils/ + +What: /sys/devices/system/memory/memoryX/removable +Date: June 2008 +Contact: Badari Pulavarty +Description: + The file /sys/devices/system/memory/memoryX/removable + indicates whether this memory block is removable or not. + This is useful for a user-level agent to determine + identify removable sections of the memory before attempting + potentially expensive hot-remove memory operation + +Users: hotplug memory remove tools + https://w3.opensource.ibm.com/projects/powerpc-utils/ diff --git a/Documentation/ABI/testing/sysfs-kernel-mm b/Documentation/ABI/testing/sysfs-kernel-mm new file mode 100644 index 0000000000000000000000000000000000000000..190d523ac159f64c97ae7355f230c46f564e5f6b --- /dev/null +++ b/Documentation/ABI/testing/sysfs-kernel-mm @@ -0,0 +1,6 @@ +What: /sys/kernel/mm +Date: July 2008 +Contact: Nishanth Aravamudan , VM maintainers +Description: + /sys/kernel/mm/ should contain any and all VM + related information in /sys/kernel/. diff --git a/Documentation/ABI/testing/sysfs-kernel-mm-hugepages b/Documentation/ABI/testing/sysfs-kernel-mm-hugepages new file mode 100644 index 0000000000000000000000000000000000000000..e21c00571cf4f082b04f12b168e376c500bd845d --- /dev/null +++ b/Documentation/ABI/testing/sysfs-kernel-mm-hugepages @@ -0,0 +1,15 @@ +What: /sys/kernel/mm/hugepages/ +Date: June 2008 +Contact: Nishanth Aravamudan , hugetlb maintainers +Description: + /sys/kernel/mm/hugepages/ contains a number of subdirectories + of the form hugepages-kB, where is the page size + of the hugepages supported by the kernel/CPU combination. + + Under these directories are a number of files: + nr_hugepages + nr_overcommit_hugepages + free_hugepages + surplus_hugepages + resv_hugepages + See Documentation/vm/hugetlbpage.txt for details. diff --git a/Documentation/CodingStyle b/Documentation/CodingStyle index 6caa146155788c8a67fc940c1879f2faf4fac1bb..1875e502f87205a1dcaf268d0af78127ee336144 100644 --- a/Documentation/CodingStyle +++ b/Documentation/CodingStyle @@ -474,25 +474,29 @@ make a good program). So, you can either get rid of GNU emacs, or change it to use saner values. To do the latter, you can stick the following in your .emacs file: -(defun linux-c-mode () - "C mode with adjusted defaults for use with the Linux kernel." - (interactive) - (c-mode) - (c-set-style "K&R") - (setq tab-width 8) - (setq indent-tabs-mode t) - (setq c-basic-offset 8)) - -This will define the M-x linux-c-mode command. When hacking on a -module, if you put the string -*- linux-c -*- somewhere on the first -two lines, this mode will be automatically invoked. Also, you may want -to add - -(setq auto-mode-alist (cons '("/usr/src/linux.*/.*\\.[ch]$" . linux-c-mode) - auto-mode-alist)) - -to your .emacs file if you want to have linux-c-mode switched on -automagically when you edit source files under /usr/src/linux. +(defun c-lineup-arglist-tabs-only (ignored) + "Line up argument lists by tabs, not spaces" + (let* ((anchor (c-langelem-pos c-syntactic-element)) + (column (c-langelem-2nd-pos c-syntactic-element)) + (offset (- (1+ column) anchor)) + (steps (floor offset c-basic-offset))) + (* (max steps 1) + c-basic-offset))) + +(add-hook 'c-mode-hook + (lambda () + (let ((filename (buffer-file-name))) + ;; Enable kernel mode for the appropriate files + (when (and filename + (string-match "~/src/linux-trees" filename)) + (setq indent-tabs-mode t) + (c-set-style "linux") + (c-set-offset 'arglist-cont-nonempty + '(c-lineup-gcc-asm-reg + c-lineup-arglist-tabs-only)))))) + +This will make emacs go better with the kernel coding style for C +files below ~/src/linux-trees. But even if you fail in getting emacs to do sane formatting, not everything is lost: use "indent". diff --git a/Documentation/DMA-API.txt b/Documentation/DMA-API.txt index 80d150458c80c5ac7f7f5f75b3e6ff8a602a19ca..d8b63d164e41193927af2c7fb41dcb0893f57878 100644 --- a/Documentation/DMA-API.txt +++ b/Documentation/DMA-API.txt @@ -298,10 +298,10 @@ recommended that you never use these unless you really know what the cache width is. int -dma_mapping_error(dma_addr_t dma_addr) +dma_mapping_error(struct device *dev, dma_addr_t dma_addr) int -pci_dma_mapping_error(dma_addr_t dma_addr) +pci_dma_mapping_error(struct pci_dev *hwdev, dma_addr_t dma_addr) In some circumstances dma_map_single and dma_map_page will fail to create a mapping. A driver can check for these errors by testing the returned diff --git a/Documentation/DMA-attributes.txt b/Documentation/DMA-attributes.txt index 6d772f84b477c9f5a4698e87d50fb63649af83d3..b768cc0e402b8e6f1cfa8ae0b0f23c4e1c50168a 100644 --- a/Documentation/DMA-attributes.txt +++ b/Documentation/DMA-attributes.txt @@ -22,3 +22,12 @@ ready and available in memory. The DMA of the "completion indication" could race with data DMA. Mapping the memory used for completion indications with DMA_ATTR_WRITE_BARRIER would prevent the race. +DMA_ATTR_WEAK_ORDERING +---------------------- + +DMA_ATTR_WEAK_ORDERING specifies that reads and writes to the mapping +may be weakly ordered, that is that reads and writes may pass each other. + +Since it is optional for platforms to implement DMA_ATTR_WEAK_ORDERING, +those that do not will simply ignore the attribute and exhibit default +behavior. diff --git a/Documentation/DocBook/gadget.tmpl b/Documentation/DocBook/gadget.tmpl index 5a8ffa761e09991bfc59dc97fa01a4deef94e9f7..ea3bc9565e6a7e7ae48a168841c222e07bfd0154 100644 --- a/Documentation/DocBook/gadget.tmpl +++ b/Documentation/DocBook/gadget.tmpl @@ -524,6 +524,44 @@ These utilities include endpoint autoconfiguration. +Composite Device Framework + +The core API is sufficient for writing drivers for composite +USB devices (with more than one function in a given configuration), +and also multi-configuration devices (also more than one function, +but not necessarily sharing a given configuration). +There is however an optional framework which makes it easier to +reuse and combine functions. + + +Devices using this framework provide a struct +usb_composite_driver, which in turn provides one or +more struct usb_configuration instances. +Each such configuration includes at least one +struct usb_function, which packages a user +visible role such as "network link" or "mass storage device". +Management functions may also exist, such as "Device Firmware +Upgrade". + + +!Iinclude/linux/usb/composite.h +!Edrivers/usb/gadget/composite.c + + + +Composite Device Functions + +At this writing, a few of the current gadget drivers have +been converted to this framework. +Near-term plans include converting all of them, except for "gadgetfs". + + +!Edrivers/usb/gadget/f_acm.c +!Edrivers/usb/gadget/f_serial.c + + + + Peripheral Controller Drivers diff --git a/Documentation/DocBook/kernel-locking.tmpl b/Documentation/DocBook/kernel-locking.tmpl index 2510763295d09dfbd893e288d1948c9b05feda4d..084f6ad7b7a0a4729b85aea3cc5c3e6eb6557689 100644 --- a/Documentation/DocBook/kernel-locking.tmpl +++ b/Documentation/DocBook/kernel-locking.tmpl @@ -219,10 +219,10 @@ - Three Main Types of Kernel Locks: Spinlocks, Mutexes and Semaphores + Two Main Types of Kernel Locks: Spinlocks and Mutexes - There are three main types of kernel locks. The fundamental type + There are two main types of kernel locks. The fundamental type is the spinlock (include/asm/spinlock.h), which is a very simple single-holder lock: if you can't get the @@ -239,14 +239,6 @@ can't sleep (see ), and so have to use a spinlock instead. - - The third type is a semaphore - (include/linux/semaphore.h): it - can have more than one holder at any time (the number decided at - initialization time), although it is most commonly used as a - single-holder lock (a mutex). If you can't get a semaphore, your - task will be suspended and later on woken up - just like for mutexes. - Neither type of lock is recursive: see . @@ -278,7 +270,7 @@ - Semaphores still exist, because they are required for + Mutexes still exist, because they are required for synchronization between user contexts, as we will see below. @@ -289,18 +281,17 @@ If you have a data structure which is only ever accessed from - user context, then you can use a simple semaphore - (linux/linux/semaphore.h) to protect it. This - is the most trivial case: you initialize the semaphore to the number - of resources available (usually 1), and call - down_interruptible() to grab the semaphore, and - up() to release it. There is also a - down(), which should be avoided, because it + user context, then you can use a simple mutex + (include/linux/mutex.h) to protect it. This + is the most trivial case: you initialize the mutex. Then you can + call mutex_lock_interruptible() to grab the mutex, + and mutex_unlock() to release it. There is also a + mutex_lock(), which should be avoided, because it will not return if a signal is received. - Example: linux/net/core/netfilter.c allows + Example: net/netfilter/nf_sockopt.c allows registration of new setsockopt() and getsockopt() calls, with nf_register_sockopt(). Registration and @@ -515,7 +506,7 @@ If you are in a process context (any syscall) and want to - lock other process out, use a semaphore. You can take a semaphore + lock other process out, use a mutex. You can take a mutex and sleep (copy_from_user*( or kmalloc(x,GFP_KERNEL)). @@ -662,7 +653,7 @@ SLBH SLBH SLBH -DI +MLI None @@ -692,8 +683,8 @@ spin_lock_bh -DI -down_interruptible +MLI +mutex_lock_interruptible @@ -1310,7 +1301,7 @@ as Alan Cox says, Lock data, not code. There is a coding bug where a piece of code tries to grab a spinlock twice: it will spin forever, waiting for the lock to - be released (spinlocks, rwlocks and semaphores are not + be released (spinlocks, rwlocks and mutexes are not recursive in Linux). This is trivial to diagnose: not a stay-up-five-nights-talk-to-fluffy-code-bunnies kind of problem. @@ -1335,7 +1326,7 @@ as Alan Cox says, Lock data, not code. This complete lockup is easy to diagnose: on SMP boxes the - watchdog timer or compiling with DEBUG_SPINLOCKS set + watchdog timer or compiling with DEBUG_SPINLOCK set (include/linux/spinlock.h) will show this up immediately when it happens. @@ -1558,7 +1549,7 @@ the amount of locking which needs to be done. Read/Write Lock Variants - Both spinlocks and semaphores have read/write variants: + Both spinlocks and mutexes have read/write variants: rwlock_t and struct rw_semaphore. These divide users into two classes: the readers and the writers. If you are only reading the data, you can get a read lock, but to write to @@ -1681,7 +1672,7 @@ the amount of locking which needs to be done. #include <linux/slab.h> #include <linux/string.h> +#include <linux/rcupdate.h> - #include <linux/semaphore.h> + #include <linux/mutex.h> #include <asm/errno.h> struct object @@ -1913,7 +1904,7 @@ machines due to caching. - put_user() + put_user() @@ -1927,13 +1918,13 @@ machines due to caching. - down_interruptible() and - down() + mutex_lock_interruptible() and + mutex_lock() - There is a down_trylock() which can be + There is a mutex_trylock() which can be used inside interrupt context, as it will not sleep. - up() will also never sleep. + mutex_unlock() will also never sleep. @@ -2023,7 +2014,7 @@ machines due to caching. Prior to 2.5, or when CONFIG_PREEMPT is unset, processes in user context inside the kernel would not - preempt each other (ie. you had that CPU until you have it up, + preempt each other (ie. you had that CPU until you gave it up, except for interrupts). With the addition of CONFIG_PREEMPT in 2.5.4, this changed: when in user context, higher priority tasks can "cut in": spinlocks diff --git a/Documentation/DocBook/procfs-guide.tmpl b/Documentation/DocBook/procfs-guide.tmpl index 1fd6a1ec7591d5f4179cdf2a641f1b055c1f486a..8a5dc6e021ffa8b16b6dc2f997e115e77b1aaf70 100644 --- a/Documentation/DocBook/procfs-guide.tmpl +++ b/Documentation/DocBook/procfs-guide.tmpl @@ -29,12 +29,12 @@ - 1.0  + 1.0 May 30, 2001 Initial revision posted to linux-kernel - 1.1  + 1.1 June 3, 2001 Revised after comments from linux-kernel diff --git a/Documentation/DocBook/uio-howto.tmpl b/Documentation/DocBook/uio-howto.tmpl index fdd7f4f887b75ba7bc96b7ab81b9abc7d3348d73..df87d1b93605ac54cf400bd7b8d44b0866d0789a 100644 --- a/Documentation/DocBook/uio-howto.tmpl +++ b/Documentation/DocBook/uio-howto.tmpl @@ -21,6 +21,18 @@ + + 2006-2008 + Hans-Jürgen Koch. + + + + +This documentation is Free Software licensed under the terms of the +GPL version 2. + + + 2006-12-11 @@ -29,6 +41,12 @@ + + 0.5 + 2008-05-22 + hjk + Added description of write() function. + 0.4 2007-11-26 @@ -57,20 +75,9 @@ - + About this document - - -Copyright and License - - Copyright (c) 2006 by Hans-Jürgen Koch. - -This documentation is Free Software licensed under the terms of the -GPL version 2. - - - Translations @@ -189,6 +196,30 @@ interested in translating it, please email me represents the total interrupt count. You can use this number to figure out if you missed some interrupts. + + For some hardware that has more than one interrupt source internally, + but not separate IRQ mask and status registers, there might be + situations where userspace cannot determine what the interrupt source + was if the kernel handler disables them by writing to the chip's IRQ + register. In such a case, the kernel has to disable the IRQ completely + to leave the chip's register untouched. Now the userspace part can + determine the cause of the interrupt, but it cannot re-enable + interrupts. Another cornercase is chips where re-enabling interrupts + is a read-modify-write operation to a combined IRQ status/acknowledge + register. This would be racy if a new interrupt occurred + simultaneously. + + + To address these problems, UIO also implements a write() function. It + is normally not used and can be ignored for hardware that has only a + single interrupt source or has separate IRQ mask and status registers. + If you need it, however, a write to /dev/uioX + will call the irqcontrol() function implemented + by the driver. You have to write a 32-bit value that is usually either + 0 or 1 to disable or enable interrupts. If a driver does not implement + irqcontrol(), write() will + return with -ENOSYS. + To handle interrupts properly, your custom kernel module can @@ -362,6 +393,14 @@ device is actually used. open(), you will probably also want a custom release() function. + + +int (*irqcontrol)(struct uio_info *info, s32 irq_on) +: Optional. If you need to be able to enable or disable +interrupts from userspace by writing to /dev/uioX, +you can implement this function. The parameter irq_on +will be 0 to disable interrupts and 1 to enable them. + diff --git a/Documentation/HOWTO b/Documentation/HOWTO index 619e8caf30db88508a3f2859d140f41ce363f552..c2371c5a98f99b5eaa785bd0affd6c40187e84e3 100644 --- a/Documentation/HOWTO +++ b/Documentation/HOWTO @@ -358,7 +358,7 @@ Here is a list of some of the different kernel trees available: - pcmcia, Dominik Brodowski git.kernel.org:/pub/scm/linux/kernel/git/brodo/pcmcia-2.6.git - - SCSI, James Bottomley + - SCSI, James Bottomley git.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6.git - x86, Ingo Molnar diff --git a/Documentation/Intel-IOMMU.txt b/Documentation/Intel-IOMMU.txt index c2321903aa09adea7f64c00d300814cc32229d1f..21bc416d887efdfabfe4c03b22639b225d72909c 100644 --- a/Documentation/Intel-IOMMU.txt +++ b/Documentation/Intel-IOMMU.txt @@ -48,7 +48,7 @@ IOVA generation is pretty generic. We used the same technique as vmalloc() but these are not global address spaces, but separate for each domain. Different DMA engines may support different number of domains. -We also allocate gaurd pages with each mapping, so we can attempt to catch +We also allocate guard pages with each mapping, so we can attempt to catch any overflow that might happen. @@ -112,4 +112,4 @@ TBD - For compatibility testing, could use unity map domain for all devices, just provide a 1-1 for all useful memory under a single domain for all devices. -- API for paravirt ops for abstracting functionlity for VMM folks. +- API for paravirt ops for abstracting functionality for VMM folks. diff --git a/Documentation/SubmittingPatches b/Documentation/SubmittingPatches index 118ca6e9404f47ded06c7ee3a287003d00377e56..f79ad9ff6031aa4ee622d9f0be3e0c1604e2d14b 100644 --- a/Documentation/SubmittingPatches +++ b/Documentation/SubmittingPatches @@ -528,7 +528,33 @@ See more details on the proper patch format in the following references. +16) Sending "git pull" requests (from Linus emails) +Please write the git repo address and branch name alone on the same line +so that I can't even by mistake pull from the wrong branch, and so +that a triple-click just selects the whole thing. + +So the proper format is something along the lines of: + + "Please pull from + + git://jdelvare.pck.nerim.net/jdelvare-2.6 i2c-for-linus + + to get these changes:" + +so that I don't have to hunt-and-peck for the address and inevitably +get it wrong (actually, I've only gotten it wrong a few times, and +checking against the diffstat tells me when I get it wrong, but I'm +just a lot more comfortable when I don't have to "look for" the right +thing to pull, and double-check that I have the right branch-name). + + +Please use "git diff -M --stat --summary" to generate the diffstat: +the -M enables rename detection, and the summary enables a summary of +new/deleted or renamed files. + +With rename detection, the statistics are rather different [...] +because git will notice that a fair number of the changes are renames. ----------------------------------- SECTION 2 - HINTS, TIPS, AND TRICKS diff --git a/Documentation/accounting/delay-accounting.txt b/Documentation/accounting/delay-accounting.txt index 1443cd71d2631241f13286e544296ef286d91c90..8a12f0730c94da018615aebc8e657daf65eadd80 100644 --- a/Documentation/accounting/delay-accounting.txt +++ b/Documentation/accounting/delay-accounting.txt @@ -11,6 +11,7 @@ the delays experienced by a task while a) waiting for a CPU (while being runnable) b) completion of synchronous block I/O initiated by the task c) swapping in pages +d) memory reclaim and makes these statistics available to userspace through the taskstats interface. @@ -41,7 +42,7 @@ this structure. See include/linux/taskstats.h for a description of the fields pertaining to delay accounting. It will generally be in the form of counters returning the cumulative -delay seen for cpu, sync block I/O, swapin etc. +delay seen for cpu, sync block I/O, swapin, memory reclaim etc. Taking the difference of two successive readings of a given counter (say cpu_delay_total) for a task will give the delay @@ -94,7 +95,9 @@ CPU count real total virtual total delay total 7876 92005750 100000000 24001500 IO count delay total 0 0 -MEM count delay total +SWAP count delay total + 0 0 +RECLAIM count delay total 0 0 Get delays seen in executing a given simple command @@ -108,5 +111,7 @@ CPU count real total virtual total delay total 6 4000250 4000000 0 IO count delay total 0 0 -MEM count delay total +SWAP count delay total + 0 0 +RECLAIM count delay total 0 0 diff --git a/Documentation/accounting/getdelays.c b/Documentation/accounting/getdelays.c index 40121b5cca14cab3993000c53078ef2d8484f001..3f7755f3963f11fd31ba598a8f6199371c87202f 100644 --- a/Documentation/accounting/getdelays.c +++ b/Documentation/accounting/getdelays.c @@ -196,14 +196,18 @@ void print_delayacct(struct taskstats *t) " %15llu%15llu%15llu%15llu\n" "IO %15s%15s\n" " %15llu%15llu\n" - "MEM %15s%15s\n" + "SWAP %15s%15s\n" + " %15llu%15llu\n" + "RECLAIM %12s%15s\n" " %15llu%15llu\n", "count", "real total", "virtual total", "delay total", t->cpu_count, t->cpu_run_real_total, t->cpu_run_virtual_total, t->cpu_delay_total, "count", "delay total", t->blkio_count, t->blkio_delay_total, - "count", "delay total", t->swapin_count, t->swapin_delay_total); + "count", "delay total", t->swapin_count, t->swapin_delay_total, + "count", "delay total", + t->freepages_count, t->freepages_delay_total); } void task_context_switch_counts(struct taskstats *t) diff --git a/Documentation/accounting/taskstats-struct.txt b/Documentation/accounting/taskstats-struct.txt index cd784f46bf8abefb9ed24257aaf5fcf4df2ecb00..e7512c061c1572f5127b7bb861ded0f0515bc6af 100644 --- a/Documentation/accounting/taskstats-struct.txt +++ b/Documentation/accounting/taskstats-struct.txt @@ -6,7 +6,7 @@ This document contains an explanation of the struct taskstats fields. There are three different groups of fields in the struct taskstats: 1) Common and basic accounting fields - If CONFIG_TASKSTATS is set, the taskstats inteface is enabled and + If CONFIG_TASKSTATS is set, the taskstats interface is enabled and the common fields and basic accounting fields are collected for delivery at do_exit() of a task. 2) Delay accounting fields @@ -26,6 +26,8 @@ There are three different groups of fields in the struct taskstats: 5) Time accounting for SMT machines +6) Extended delay accounting fields for memory reclaim + Future extension should add fields to the end of the taskstats struct, and should not change the relative position of each field within the struct. @@ -170,4 +172,9 @@ struct taskstats { __u64 ac_utimescaled; /* utime scaled on frequency etc */ __u64 ac_stimescaled; /* stime scaled on frequency etc */ __u64 cpu_scaled_run_real_total; /* scaled cpu_run_real_total */ + +6) Extended delay accounting fields for memory reclaim + /* Delay waiting for memory reclaim */ + __u64 freepages_count; + __u64 freepages_delay_total; } diff --git a/Documentation/arm/Interrupts b/Documentation/arm/Interrupts index 0d3dbf1099bcc90cae1b364002ef32e15dcdc06a..c202ed35d7d610dd3c399b50fdb65796917f1544 100644 --- a/Documentation/arm/Interrupts +++ b/Documentation/arm/Interrupts @@ -138,14 +138,8 @@ So, what's changed? Set active the IRQ edge(s)/level. This replaces the SA1111 INTPOL manipulation, and the set_GPIO_IRQ_edge() - function. Type should be one of the following: - - #define IRQT_NOEDGE (0) - #define IRQT_RISING (__IRQT_RISEDGE) - #define IRQT_FALLING (__IRQT_FALEDGE) - #define IRQT_BOTHEDGE (__IRQT_RISEDGE|__IRQT_FALEDGE) - #define IRQT_LOW (__IRQT_LOWLVL) - #define IRQT_HIGH (__IRQT_HIGHLVL) + function. Type should be one of IRQ_TYPE_xxx defined in + 3. set_GPIO_IRQ_edge() is obsolete, and should be replaced by set_irq_type. diff --git a/Documentation/bt8xxgpio.txt b/Documentation/bt8xxgpio.txt new file mode 100644 index 0000000000000000000000000000000000000000..d8297e4ebd265eb5dd273bad20162e51d369b25a --- /dev/null +++ b/Documentation/bt8xxgpio.txt @@ -0,0 +1,67 @@ +=============================================================== +== BT8XXGPIO driver == +== == +== A driver for a selfmade cheap BT8xx based PCI GPIO-card == +== == +== For advanced documentation, see == +== http://www.bu3sch.de/btgpio.php == +=============================================================== + + +A generic digital 24-port PCI GPIO card can be built out of an ordinary +Brooktree bt848, bt849, bt878 or bt879 based analog TV tuner card. The +Brooktree chip is used in old analog Hauppauge WinTV PCI cards. You can easily +find them used for low prices on the net. + +The bt8xx chip does have 24 digital GPIO ports. +These ports are accessible via 24 pins on the SMD chip package. + + +============================================== +== How to physically access the GPIO pins == +============================================== + +The are several ways to access these pins. One might unsolder the whole chip +and put it on a custom PCI board, or one might only unsolder each individual +GPIO pin and solder that to some tiny wire. As the chip package really is tiny +there are some advanced soldering skills needed in any case. + +The physical pinouts are drawn in the following ASCII art. +The GPIO pins are marked with G00-G23 + + G G G G G G G G G G G G G G G G G G + 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 + 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 + | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | + --------------------------------------------------------------------------- + --| ^ ^ |-- + --| pin 86 pin 67 |-- + --| |-- + --| pin 61 > |-- G18 + --| |-- G19 + --| |-- G20 + --| |-- G21 + --| |-- G22 + --| pin 56 > |-- G23 + --| |-- + --| Brooktree 878/879 |-- + --| |-- + --| |-- + --| |-- + --| |-- + --| |-- + --| |-- + --| |-- + --| |-- + --| |-- + --| |-- + --| |-- + --| |-- + --| |-- + --| O |-- + --| |-- + --------------------------------------------------------------------------- + | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | + ^ + This is pin 1 + diff --git a/Documentation/controllers/memory.txt b/Documentation/controllers/memory.txt index 866b9cd9a9590d6b6b8c3d577038e8d51234082b..9b53d5827361fd647f3388212e648f502defc698 100644 --- a/Documentation/controllers/memory.txt +++ b/Documentation/controllers/memory.txt @@ -242,8 +242,7 @@ rmdir() if there are no tasks. 1. Add support for accounting huge pages (as a separate controller) 2. Make per-cgroup scanner reclaim not-shared pages first 3. Teach controller to account for shared-pages -4. Start reclamation when the limit is lowered -5. Start reclamation in the background when the limit is +4. Start reclamation in the background when the limit is not yet hit but the usage is getting closer Summary diff --git a/Documentation/cpu-freq/governors.txt b/Documentation/cpu-freq/governors.txt index dcec0564d04075a9751e462968f956385405f283..5b0cfa67aff9c89ebc6d0f9dd4d467e8be8ae71f 100644 --- a/Documentation/cpu-freq/governors.txt +++ b/Documentation/cpu-freq/governors.txt @@ -122,7 +122,7 @@ around '10000' or more. show_sampling_rate_(min|max): the minimum and maximum sampling rates available that you may set 'sampling_rate' to. -up_threshold: defines what the average CPU usaged between the samplings +up_threshold: defines what the average CPU usage between the samplings of 'sampling_rate' needs to be for the kernel to make a decision on whether it should increase the frequency. For example when it is set to its default value of '80' it means that between the checking diff --git a/Documentation/edac.txt b/Documentation/edac.txt index a5c36842ecef4ec103ff7f44b5499ed9963db0c2..8eda3fb664166726163bf59565c9d52c76af6c79 100644 --- a/Documentation/edac.txt +++ b/Documentation/edac.txt @@ -222,74 +222,9 @@ both csrow2 and csrow3 are populated, this indicates a dual ranked set of DIMMs for channels 0 and 1. -Within each of the 'mc','mcX' and 'csrowX' directories are several +Within each of the 'mcX' and 'csrowX' directories are several EDAC control and attribute files. - -============================================================================ -DIRECTORY 'mc' - -In directory 'mc' are EDAC system overall control and attribute files: - - -Panic on UE control file: - - 'edac_mc_panic_on_ue' - - An uncorrectable error will cause a machine panic. This is usually - desirable. It is a bad idea to continue when an uncorrectable error - occurs - it is indeterminate what was uncorrected and the operating - system context might be so mangled that continuing will lead to further - corruption. If the kernel has MCE configured, then EDAC will never - notice the UE. - - LOAD TIME: module/kernel parameter: panic_on_ue=[0|1] - - RUN TIME: echo "1" >/sys/devices/system/edac/mc/edac_mc_panic_on_ue - - -Log UE control file: - - 'edac_mc_log_ue' - - Generate kernel messages describing uncorrectable errors. These errors - are reported through the system message log system. UE statistics - will be accumulated even when UE logging is disabled. - - LOAD TIME: module/kernel parameter: log_ue=[0|1] - - RUN TIME: echo "1" >/sys/devices/system/edac/mc/edac_mc_log_ue - - -Log CE control file: - - 'edac_mc_log_ce' - - Generate kernel messages describing correctable errors. These - errors are reported through the system message log system. - CE statistics will be accumulated even when CE logging is disabled. - - LOAD TIME: module/kernel parameter: log_ce=[0|1] - - RUN TIME: echo "1" >/sys/devices/system/edac/mc/edac_mc_log_ce - - -Polling period control file: - - 'edac_mc_poll_msec' - - The time period, in milliseconds, for polling for error information. - Too small a value wastes resources. Too large a value might delay - necessary handling of errors and might loose valuable information for - locating the error. 1000 milliseconds (once each second) is the current - default. Systems which require all the bandwidth they can get, may - increase this. - - LOAD TIME: module/kernel parameter: poll_msec=[0|1] - - RUN TIME: echo "1000" >/sys/devices/system/edac/mc/edac_mc_poll_msec - - ============================================================================ 'mcX' DIRECTORIES @@ -392,7 +327,7 @@ Sdram memory scrubbing rate: 'sdram_scrub_rate' Read/Write attribute file that controls memory scrubbing. The scrubbing - rate is set by writing a minimum bandwith in bytes/sec to the attribute + rate is set by writing a minimum bandwidth in bytes/sec to the attribute file. The rate will be translated to an internal value that gives at least the specified rate. @@ -537,7 +472,6 @@ Channel 1 DIMM Label control file: motherboard specific and determination of this information must occur in userland at this time. - ============================================================================ SYSTEM LOGGING @@ -570,7 +504,6 @@ error type, a notice of "no info" and then an optional, driver-specific error message. - ============================================================================ PCI Bus Parity Detection @@ -604,6 +537,74 @@ Enable/Disable PCI Parity checking control file: echo "0" >/sys/devices/system/edac/pci/check_pci_parity +Parity Count: + + 'pci_parity_count' + + This attribute file will display the number of parity errors that + have been detected. + + +============================================================================ +MODULE PARAMETERS + +Panic on UE control file: + + 'edac_mc_panic_on_ue' + + An uncorrectable error will cause a machine panic. This is usually + desirable. It is a bad idea to continue when an uncorrectable error + occurs - it is indeterminate what was uncorrected and the operating + system context might be so mangled that continuing will lead to further + corruption. If the kernel has MCE configured, then EDAC will never + notice the UE. + + LOAD TIME: module/kernel parameter: edac_mc_panic_on_ue=[0|1] + + RUN TIME: echo "1" > /sys/module/edac_core/parameters/edac_mc_panic_on_ue + + +Log UE control file: + + 'edac_mc_log_ue' + + Generate kernel messages describing uncorrectable errors. These errors + are reported through the system message log system. UE statistics + will be accumulated even when UE logging is disabled. + + LOAD TIME: module/kernel parameter: edac_mc_log_ue=[0|1] + + RUN TIME: echo "1" > /sys/module/edac_core/parameters/edac_mc_log_ue + + +Log CE control file: + + 'edac_mc_log_ce' + + Generate kernel messages describing correctable errors. These + errors are reported through the system message log system. + CE statistics will be accumulated even when CE logging is disabled. + + LOAD TIME: module/kernel parameter: edac_mc_log_ce=[0|1] + + RUN TIME: echo "1" > /sys/module/edac_core/parameters/edac_mc_log_ce + + +Polling period control file: + + 'edac_mc_poll_msec' + + The time period, in milliseconds, for polling for error information. + Too small a value wastes resources. Too large a value might delay + necessary handling of errors and might loose valuable information for + locating the error. 1000 milliseconds (once each second) is the current + default. Systems which require all the bandwidth they can get, may + increase this. + + LOAD TIME: module/kernel parameter: edac_mc_poll_msec=[0|1] + + RUN TIME: echo "1000" > /sys/module/edac_core/parameters/edac_mc_poll_msec + Panic on PCI PARITY Error: @@ -614,21 +615,13 @@ Panic on PCI PARITY Error: error has been detected. - module/kernel parameter: panic_on_pci_parity=[0|1] + module/kernel parameter: edac_panic_on_pci_pe=[0|1] Enable: - echo "1" >/sys/devices/system/edac/pci/panic_on_pci_parity + echo "1" > /sys/module/edac_core/parameters/edac_panic_on_pci_pe Disable: - echo "0" >/sys/devices/system/edac/pci/panic_on_pci_parity - - -Parity Count: - - 'pci_parity_count' - - This attribute file will display the number of parity errors that - have been detected. + echo "0" > /sys/module/edac_core/parameters/edac_panic_on_pci_pe diff --git a/Documentation/fb/sh7760fb.txt b/Documentation/fb/sh7760fb.txt new file mode 100644 index 0000000000000000000000000000000000000000..c87bfe5c630a16893aed884a86f6e39506d94182 --- /dev/null +++ b/Documentation/fb/sh7760fb.txt @@ -0,0 +1,131 @@ +SH7760/SH7763 integrated LCDC Framebuffer driver +================================================ + +0. Overwiew +----------- +The SH7760/SH7763 have an integrated LCD Display controller (LCDC) which +supports (in theory) resolutions ranging from 1x1 to 1024x1024, +with color depths ranging from 1 to 16 bits, on STN, DSTN and TFT Panels. + +Caveats: +* Framebuffer memory must be a large chunk allocated at the top + of Area3 (HW requirement). Because of this requirement you should NOT + make the driver a module since at runtime it may become impossible to + get a large enough contiguous chunk of memory. + +* The driver does not support changing resolution while loaded + (displays aren't hotpluggable anyway) + +* Heavy flickering may be observed + a) if you're using 15/16bit color modes at >= 640x480 px resolutions, + b) during PCMCIA (or any other slow bus) activity. + +* Rotation works only 90degress clockwise, and only if horizontal + resolution is <= 320 pixels. + +files: drivers/video/sh7760fb.c + include/asm-sh/sh7760fb.h + Documentation/fb/sh7760fb.txt + +1. Platform setup +----------------- +SH7760: + Video data is fetched via the DMABRG DMA engine, so you have to + configure the SH DMAC for DMABRG mode (write 0x94808080 to the + DMARSRA register somewhere at boot). + + PFC registers PCCR and PCDR must be set to peripheral mode. + (write zeros to both). + +The driver does NOT do the above for you since board setup is, well, job +of the board setup code. + +2. Panel definitions +-------------------- +The LCDC must explicitly be told about the type of LCD panel +attached. Data must be wrapped in a "struct sh7760fb_platdata" and +passed to the driver as platform_data. + +Suggest you take a closer look at the SH7760 Manual, Section 30. +(http://documentation.renesas.com/eng/products/mpumcu/e602291_sh7760.pdf) + +The following code illustrates what needs to be done to +get the framebuffer working on a 640x480 TFT: + +====================== cut here ====================================== + +#include +#include + +/* + * NEC NL6440bc26-01 640x480 TFT + * dotclock 25175 kHz + * Xres 640 Yres 480 + * Htotal 800 Vtotal 525 + * HsynStart 656 VsynStart 490 + * HsynLenn 30 VsynLenn 2 + * + * The linux framebuffer layer does not use the syncstart/synclen + * values but right/left/upper/lower margin values. The comments + * for the x_margin explain how to calculate those from given + * panel sync timings. + */ +static struct fb_videomode nl6448bc26 = { + .name = "NL6448BC26", + .refresh = 60, + .xres = 640, + .yres = 480, + .pixclock = 39683, /* in picoseconds! */ + .hsync_len = 30, + .vsync_len = 2, + .left_margin = 114, /* HTOT - (HSYNSLEN + HSYNSTART) */ + .right_margin = 16, /* HSYNSTART - XRES */ + .upper_margin = 33, /* VTOT - (VSYNLEN + VSYNSTART) */ + .lower_margin = 10, /* VSYNSTART - YRES */ + .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT, + .vmode = FB_VMODE_NONINTERLACED, + .flag = 0, +}; + +static struct sh7760fb_platdata sh7760fb_nl6448 = { + .def_mode = &nl6448bc26, + .ldmtr = LDMTR_TFT_COLOR_16, /* 16bit TFT panel */ + .lddfr = LDDFR_8BPP, /* we want 8bit output */ + .ldpmmr = 0x0070, + .ldpspr = 0x0500, + .ldaclnr = 0, + .ldickr = LDICKR_CLKSRC(LCDC_CLKSRC_EXTERNAL) | + LDICKR_CLKDIV(1), + .rotate = 0, + .novsync = 1, + .blank = NULL, +}; + +/* SH7760: + * 0xFE300800: 256 * 4byte xRGB palette ram + * 0xFE300C00: 42 bytes ctrl registers + */ +static struct resource sh7760_lcdc_res[] = { + [0] = { + .start = 0xFE300800, + .end = 0xFE300CFF, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = 65, + .end = 65, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device sh7760_lcdc_dev = { + .dev = { + .platform_data = &sh7760fb_nl6448, + }, + .name = "sh7760-lcdc", + .id = -1, + .resource = sh7760_lcdc_res, + .num_resources = ARRAY_SIZE(sh7760_lcdc_res), +}; + +====================== cut here ====================================== diff --git a/Documentation/fb/tridentfb.txt b/Documentation/fb/tridentfb.txt index 8a6c8a43e6a37803e4fcbd640f1b4578f5a611c6..45d9de5b13a3cb9f8143484d49737ae87254fdf7 100644 --- a/Documentation/fb/tridentfb.txt +++ b/Documentation/fb/tridentfb.txt @@ -3,11 +3,25 @@ Tridentfb is a framebuffer driver for some Trident chip based cards. The following list of chips is thought to be supported although not all are tested: -those from the Image series with Cyber in their names - accelerated -those with Blade in their names (Blade3D,CyberBlade...) - accelerated -the newer CyberBladeXP family - nonaccelerated - -Only PCI/AGP based cards are supported, none of the older Tridents. +those from the TGUI series 9440/96XX and with Cyber in their names +those from the Image series and with Cyber in their names +those with Blade in their names (Blade3D,CyberBlade...) +the newer CyberBladeXP family + +All families are accelerated. Only PCI/AGP based cards are supported, +none of the older Tridents. +The driver supports 8, 16 and 32 bits per pixel depths. +The TGUI family requires a line length to be power of 2 if acceleration +is enabled. This means that range of possible resolutions and bpp is +limited comparing to the range if acceleration is disabled (see list +of parameters below). + +Known bugs: +1. The driver randomly locks up on 3DImage975 chip with acceleration + enabled. The same happens in X11 (Xorg). +2. The ramdac speeds require some more fine tuning. It is possible to + switch resolution which the chip does not support at some depths for + older chips. How to use it? ============== @@ -17,12 +31,11 @@ video=tridentfb The parameters for tridentfb are concatenated with a ':' as in this example. -video=tridentfb:800x600,bpp=16,noaccel +video=tridentfb:800x600-16@75,noaccel The second level parameters that tridentfb understands are: noaccel - turns off acceleration (when it doesn't work for your card) -accel - force text acceleration (for boards which by default are noacceled) fp - use flat panel related stuff crt - assume monitor is present instead of fp @@ -31,21 +44,24 @@ center - for flat panels and resolutions smaller than native size center the image, otherwise use stretch -memsize - integer value in Kb, use if your card's memory size is misdetected. +memsize - integer value in KB, use if your card's memory size is misdetected. look at the driver output to see what it says when initializing. -memdiff - integer value in Kb,should be nonzero if your card reports - more memory than it actually has.For instance mine is 192K less than + +memdiff - integer value in KB, should be nonzero if your card reports + more memory than it actually has. For instance mine is 192K less than detection says in all three BIOS selectable situations 2M, 4M, 8M. Only use if your video memory is taken from main memory hence of - configurable size.Otherwise use memsize. - If in some modes which barely fit the memory you see garbage at the bottom - this might help by not letting change to that mode anymore. + configurable size. Otherwise use memsize. + If in some modes which barely fit the memory you see garbage + at the bottom this might help by not letting change to that mode + anymore. nativex - the width in pixels of the flat panel.If you know it (usually 1024 800 or 1280) and it is not what the driver seems to detect use it. -bpp - bits per pixel (8,16 or 32) -mode - a mode name like 800x600 (as described in Documentation/fb/modedb.txt) +bpp - bits per pixel (8,16 or 32) +mode - a mode name like 800x600-8@75 as described in + Documentation/fb/modedb.txt Using insane values for the above parameters will probably result in driver misbehaviour so take care(for instance memsize=12345678 or memdiff=23784 or diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index 65a1482457a89ec9d6c5beec89464bc049f3f5e2..c23955404bf5d5056f7ddf448ea52415b6d3adfd 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -47,6 +47,30 @@ Who: Mauro Carvalho Chehab --------------------------- +What: old tuner-3036 i2c driver +When: 2.6.28 +Why: This driver is for VERY old i2c-over-parallel port teletext receiver + boxes. Rather then spending effort on converting this driver to V4L2, + and since it is extremely unlikely that anyone still uses one of these + devices, it was decided to drop it. +Who: Hans Verkuil + Mauro Carvalho Chehab + + --------------------------- + +What: V4L2 dpc7146 driver +When: 2.6.28 +Why: Old driver for the dpc7146 demonstration board that is no longer + relevant. The last time this was tested on actual hardware was + probably around 2002. Since this is a driver for a demonstration + board the decision was made to remove it rather than spending a + lot of effort continually updating this driver to stay in sync + with the latest internal V4L2 or I2C API. +Who: Hans Verkuil + Mauro Carvalho Chehab + +--------------------------- + What: PCMCIA control ioctl (needed for pcmcia-cs [cardmgr, cardctl]) When: November 2005 Files: drivers/pcmcia/: pcmcia_ioctl.c @@ -138,24 +162,6 @@ Who: Kay Sievers --------------------------- -What: find_task_by_pid -When: 2.6.26 -Why: With pid namespaces, calling this funciton will return the - wrong task when called from inside a namespace. - - The best way to save a task pid and find a task by this - pid later, is to find this task's struct pid pointer (or get - it directly from the task) and call pid_task() later. - - If someone really needs to get a task by its pid_t, then - he most likely needs the find_task_by_vpid() to get the - task from the same namespace as the current task is in, but - this may be not so in general. - -Who: Pavel Emelyanov - ---------------------------- - What: ACPI procfs interface When: July 2008 Why: ACPI sysfs conversion should be finished by January 2008. @@ -300,11 +306,15 @@ Who: ocfs2-devel@oss.oracle.com --------------------------- -What: asm/semaphore.h -When: 2.6.26 -Why: Implementation became generic; users should now include - linux/semaphore.h instead. -Who: Matthew Wilcox +What: SCTP_GET_PEER_ADDRS_NUM_OLD, SCTP_GET_PEER_ADDRS_OLD, + SCTP_GET_LOCAL_ADDRS_NUM_OLD, SCTP_GET_LOCAL_ADDRS_OLD +When: June 2009 +Why: A newer version of the options have been introduced in 2005 that + removes the limitions of the old API. The sctp library has been + converted to use these new options at the same time. Any user + space app that directly uses the old options should convert to using + the new options. +Who: Vlad Yasevich --------------------------- @@ -314,3 +324,23 @@ Why: This option was introduced just to allow older lm-sensors userspace to keep working over the upgrade to 2.6.26. At the scheduled time of removal fixed lm-sensors (2.x or 3.x) should be readily available. Who: Rene Herman + +--------------------------- + +What: Code that is now under CONFIG_WIRELESS_EXT_SYSFS + (in net/core/net-sysfs.c) +When: After the only user (hal) has seen a release with the patches + for enough time, probably some time in 2010. +Why: Over 1K .text/.data size reduction, data is available in other + ways (ioctls) +Who: Johannes Berg + +--------------------------- + +What: CONFIG_NF_CT_ACCT +When: 2.6.29 +Why: Accounting can now be enabled/disabled without kernel recompilation. + Currently used only to set a default value for a feature that is also + controlled by a kernel/module/sysfs/sysctl parameter. +Who: Krzysztof Piotr Oledzki + diff --git a/Documentation/filesystems/Locking b/Documentation/filesystems/Locking index 8b22d7d8b99166b6db2e037644e9c5d7ff03695e..680fb566b9286bcc71a527c5f75d4b94fc9ac215 100644 --- a/Documentation/filesystems/Locking +++ b/Documentation/filesystems/Locking @@ -510,6 +510,7 @@ prototypes: void (*close)(struct vm_area_struct*); int (*fault)(struct vm_area_struct*, struct vm_fault *); int (*page_mkwrite)(struct vm_area_struct *, struct page *); + int (*access)(struct vm_area_struct *, unsigned long, void*, int, int); locking rules: BKL mmap_sem PageLocked(page) @@ -517,6 +518,7 @@ open: no yes close: no yes fault: no yes page_mkwrite: no yes no +access: no yes ->page_mkwrite() is called when a previously read-only page is about to become writeable. The file system is responsible for @@ -525,6 +527,11 @@ taking to lock out truncate, the page range should be verified to be within i_size. The page mapping should also be checked that it is not NULL. + ->access() is called when get_user_pages() fails in +acces_process_vm(), typically used to debug a process through +/proc/pid/mem or ptrace. This function is needed only for +VM_IO | VM_PFNMAP VMAs. + ================================================================================ Dubious stuff diff --git a/Documentation/filesystems/bfs.txt b/Documentation/filesystems/bfs.txt index ea825e178e797b3b8af53d8d6d5fa2c1f1974a0d..78043d5a8fc35f01c343ced6f956aadee03e1026 100644 --- a/Documentation/filesystems/bfs.txt +++ b/Documentation/filesystems/bfs.txt @@ -26,11 +26,11 @@ You can simplify mounting by just typing: this will allocate the first available loopback device (and load loop.o kernel module if necessary) automatically. If the loopback driver is not -loaded automatically, make sure that your kernel is compiled with kmod -support (CONFIG_KMOD) enabled. Beware that umount will not -deallocate /dev/loopN device if /etc/mtab file on your system is a -symbolic link to /proc/mounts. You will need to do it manually using -"-d" switch of losetup(8). Read losetup(8) manpage for more info. +loaded automatically, make sure that you have compiled the module and +that modprobe is functioning. Beware that umount will not deallocate +/dev/loopN device if /etc/mtab file on your system is a symbolic link to +/proc/mounts. You will need to do it manually using "-d" switch of +losetup(8). Read losetup(8) manpage for more info. To create the BFS image under UnixWare you need to find out first which slice contains it. The command prtvtoc(1M) is your friend: diff --git a/Documentation/filesystems/configfs/configfs.txt b/Documentation/filesystems/configfs/configfs.txt index 15838d706ea24afaac3d1951d3452006b15d9742..44c97e6accb2655faed63b52e4bc63848571a7ab 100644 --- a/Documentation/filesystems/configfs/configfs.txt +++ b/Documentation/filesystems/configfs/configfs.txt @@ -233,12 +233,10 @@ accomplished via the group operations specified on the group's config_item_type. struct configfs_group_operations { - int (*make_item)(struct config_group *group, - const char *name, - struct config_item **new_item); - int (*make_group)(struct config_group *group, - const char *name, - struct config_group **new_group); + struct config_item *(*make_item)(struct config_group *group, + const char *name); + struct config_group *(*make_group)(struct config_group *group, + const char *name); int (*commit_item)(struct config_item *item); void (*disconnect_notify)(struct config_group *group, struct config_item *item); diff --git a/Documentation/filesystems/configfs/configfs_example.c b/Documentation/filesystems/configfs/configfs_example.c index 0b422acd470c5826e269d6a98628b4cd0d81cf07..039648791701f6e1b74a970d36f361cab695ab64 100644 --- a/Documentation/filesystems/configfs/configfs_example.c +++ b/Documentation/filesystems/configfs/configfs_example.c @@ -273,13 +273,13 @@ static inline struct simple_children *to_simple_children(struct config_item *ite return item ? container_of(to_config_group(item), struct simple_children, group) : NULL; } -static int simple_children_make_item(struct config_group *group, const char *name, struct config_item **new_item) +static struct config_item *simple_children_make_item(struct config_group *group, const char *name) { struct simple_child *simple_child; simple_child = kzalloc(sizeof(struct simple_child), GFP_KERNEL); if (!simple_child) - return -ENOMEM; + return ERR_PTR(-ENOMEM); config_item_init_type_name(&simple_child->item, name, @@ -287,8 +287,7 @@ static int simple_children_make_item(struct config_group *group, const char *nam simple_child->storeme = 0; - *new_item = &simple_child->item; - return 0; + return &simple_child->item; } static struct configfs_attribute simple_children_attr_description = { @@ -360,21 +359,20 @@ static struct configfs_subsystem simple_children_subsys = { * children of its own. */ -static int group_children_make_group(struct config_group *group, const char *name, struct config_group **new_group) +static struct config_group *group_children_make_group(struct config_group *group, const char *name) { struct simple_children *simple_children; simple_children = kzalloc(sizeof(struct simple_children), GFP_KERNEL); if (!simple_children) - return -ENOMEM; + return ERR_PTR(-ENOMEM); config_group_init_type_name(&simple_children->group, name, &simple_children_type); - *new_group = &simple_children->group; - return 0; + return &simple_children->group; } static struct configfs_attribute group_children_attr_description = { diff --git a/Documentation/filesystems/nfs-rdma.txt b/Documentation/filesystems/nfs-rdma.txt index d0ec45ae4e7dfa4585fa74c0757be4d80dc02bf5..44bd766f2e5d2225488337681a948c160bd2a821 100644 --- a/Documentation/filesystems/nfs-rdma.txt +++ b/Documentation/filesystems/nfs-rdma.txt @@ -5,7 +5,7 @@ ################################################################################ Author: NetApp and Open Grid Computing - Date: April 15, 2008 + Date: May 29, 2008 Table of Contents ~~~~~~~~~~~~~~~~~ @@ -60,16 +60,18 @@ Installation The procedures described in this document have been tested with distributions from Red Hat's Fedora Project (http://fedora.redhat.com/). - - Install nfs-utils-1.1.1 or greater on the client + - Install nfs-utils-1.1.2 or greater on the client - An NFS/RDMA mount point can only be obtained by using the mount.nfs - command in nfs-utils-1.1.1 or greater. To see which version of mount.nfs - you are using, type: + An NFS/RDMA mount point can be obtained by using the mount.nfs command in + nfs-utils-1.1.2 or greater (nfs-utils-1.1.1 was the first nfs-utils + version with support for NFS/RDMA mounts, but for various reasons we + recommend using nfs-utils-1.1.2 or greater). To see which version of + mount.nfs you are using, type: - > /sbin/mount.nfs -V + $ /sbin/mount.nfs -V - If the version is less than 1.1.1 or the command does not exist, - then you will need to install the latest version of nfs-utils. + If the version is less than 1.1.2 or the command does not exist, + you should install the latest version of nfs-utils. Download the latest package from: @@ -77,22 +79,33 @@ Installation Uncompress the package and follow the installation instructions. - If you will not be using GSS and NFSv4, the installation process - can be simplified by disabling these features when running configure: + If you will not need the idmapper and gssd executables (you do not need + these to create an NFS/RDMA enabled mount command), the installation + process can be simplified by disabling these features when running + configure: - > ./configure --disable-gss --disable-nfsv4 + $ ./configure --disable-gss --disable-nfsv4 - For more information on this see the package's README and INSTALL files. + To build nfs-utils you will need the tcp_wrappers package installed. For + more information on this see the package's README and INSTALL files. After building the nfs-utils package, there will be a mount.nfs binary in the utils/mount directory. This binary can be used to initiate NFS v2, v3, - or v4 mounts. To initiate a v4 mount, the binary must be called mount.nfs4. - The standard technique is to create a symlink called mount.nfs4 to mount.nfs. + or v4 mounts. To initiate a v4 mount, the binary must be called + mount.nfs4. The standard technique is to create a symlink called + mount.nfs4 to mount.nfs. - NOTE: mount.nfs and therefore nfs-utils-1.1.1 or greater is only needed + This mount.nfs binary should be installed at /sbin/mount.nfs as follows: + + $ sudo cp utils/mount/mount.nfs /sbin/mount.nfs + + In this location, mount.nfs will be invoked automatically for NFS mounts + by the system mount commmand. + + NOTE: mount.nfs and therefore nfs-utils-1.1.2 or greater is only needed on the NFS client machine. You do not need this specific version of nfs-utils on the server. Furthermore, only the mount.nfs command from - nfs-utils-1.1.1 is needed on the client. + nfs-utils-1.1.2 is needed on the client. - Install a Linux kernel with NFS/RDMA @@ -156,8 +169,8 @@ Check RDMA and NFS Setup this time. For example, if you are using a Mellanox Tavor/Sinai/Arbel card: - > modprobe ib_mthca - > modprobe ib_ipoib + $ modprobe ib_mthca + $ modprobe ib_ipoib If you are using InfiniBand, make sure there is a Subnet Manager (SM) running on the network. If your IB switch has an embedded SM, you can @@ -166,7 +179,7 @@ Check RDMA and NFS Setup If an SM is running on your network, you should see the following: - > cat /sys/class/infiniband/driverX/ports/1/state + $ cat /sys/class/infiniband/driverX/ports/1/state 4: ACTIVE where driverX is mthca0, ipath5, ehca3, etc. @@ -174,10 +187,10 @@ Check RDMA and NFS Setup To further test the InfiniBand software stack, use IPoIB (this assumes you have two IB hosts named host1 and host2): - host1> ifconfig ib0 a.b.c.x - host2> ifconfig ib0 a.b.c.y - host1> ping a.b.c.y - host2> ping a.b.c.x + host1$ ifconfig ib0 a.b.c.x + host2$ ifconfig ib0 a.b.c.y + host1$ ping a.b.c.y + host2$ ping a.b.c.x For other device types, follow the appropriate procedures. @@ -202,11 +215,11 @@ NFS/RDMA Setup /vol0 192.168.0.47(fsid=0,rw,async,insecure,no_root_squash) /vol0 192.168.0.0/255.255.255.0(fsid=0,rw,async,insecure,no_root_squash) - The IP address(es) is(are) the client's IPoIB address for an InfiniBand HCA or the - cleint's iWARP address(es) for an RNIC. + The IP address(es) is(are) the client's IPoIB address for an InfiniBand + HCA or the cleint's iWARP address(es) for an RNIC. - NOTE: The "insecure" option must be used because the NFS/RDMA client does not - use a reserved port. + NOTE: The "insecure" option must be used because the NFS/RDMA client does + not use a reserved port. Each time a machine boots: @@ -214,43 +227,45 @@ NFS/RDMA Setup For InfiniBand using a Mellanox adapter: - > modprobe ib_mthca - > modprobe ib_ipoib - > ifconfig ib0 a.b.c.d + $ modprobe ib_mthca + $ modprobe ib_ipoib + $ ifconfig ib0 a.b.c.d NOTE: use unique addresses for the client and server - Start the NFS server - If the NFS/RDMA server was built as a module (CONFIG_SUNRPC_XPRT_RDMA=m in kernel config), - load the RDMA transport module: + If the NFS/RDMA server was built as a module (CONFIG_SUNRPC_XPRT_RDMA=m in + kernel config), load the RDMA transport module: - > modprobe svcrdma + $ modprobe svcrdma - Regardless of how the server was built (module or built-in), start the server: + Regardless of how the server was built (module or built-in), start the + server: - > /etc/init.d/nfs start + $ /etc/init.d/nfs start or - > service nfs start + $ service nfs start Instruct the server to listen on the RDMA transport: - > echo rdma 2050 > /proc/fs/nfsd/portlist + $ echo rdma 2050 > /proc/fs/nfsd/portlist - On the client system - If the NFS/RDMA client was built as a module (CONFIG_SUNRPC_XPRT_RDMA=m in kernel config), - load the RDMA client module: + If the NFS/RDMA client was built as a module (CONFIG_SUNRPC_XPRT_RDMA=m in + kernel config), load the RDMA client module: - > modprobe xprtrdma.ko + $ modprobe xprtrdma.ko - Regardless of how the client was built (module or built-in), issue the mount.nfs command: + Regardless of how the client was built (module or built-in), use this + command to mount the NFS/RDMA server: - > /path/to/your/mount.nfs :/ /mnt -i -o rdma,port=2050 + $ mount -o rdma,port=2050 :/ /mnt - To verify that the mount is using RDMA, run "cat /proc/mounts" and check the - "proto" field for the given mount. + To verify that the mount is using RDMA, run "cat /proc/mounts" and check + the "proto" field for the given mount. Congratulations! You're using NFS/RDMA! diff --git a/Documentation/filesystems/omfs.txt b/Documentation/filesystems/omfs.txt new file mode 100644 index 0000000000000000000000000000000000000000..1d0d41ff5c65cdc75454d958ad58b367a9e2464c --- /dev/null +++ b/Documentation/filesystems/omfs.txt @@ -0,0 +1,106 @@ +Optimized MPEG Filesystem (OMFS) + +Overview +======== + +OMFS is a filesystem created by SonicBlue for use in the ReplayTV DVR +and Rio Karma MP3 player. The filesystem is extent-based, utilizing +block sizes from 2k to 8k, with hash-based directories. This +filesystem driver may be used to read and write disks from these +devices. + +Note, it is not recommended that this FS be used in place of a general +filesystem for your own streaming media device. Native Linux filesystems +will likely perform better. + +More information is available at: + + http://linux-karma.sf.net/ + +Various utilities, including mkomfs and omfsck, are included with +omfsprogs, available at: + + http://bobcopeland.com/karma/ + +Instructions are included in its README. + +Options +======= + +OMFS supports the following mount-time options: + + uid=n - make all files owned by specified user + gid=n - make all files owned by specified group + umask=xxx - set permission umask to xxx + fmask=xxx - set umask to xxx for files + dmask=xxx - set umask to xxx for directories + +Disk format +=========== + +OMFS discriminates between "sysblocks" and normal data blocks. The sysblock +group consists of super block information, file metadata, directory structures, +and extents. Each sysblock has a header containing CRCs of the entire +sysblock, and may be mirrored in successive blocks on the disk. A sysblock may +have a smaller size than a data block, but since they are both addressed by the +same 64-bit block number, any remaining space in the smaller sysblock is +unused. + +Sysblock header information: + +struct omfs_header { + __be64 h_self; /* FS block where this is located */ + __be32 h_body_size; /* size of useful data after header */ + __be16 h_crc; /* crc-ccitt of body_size bytes */ + char h_fill1[2]; + u8 h_version; /* version, always 1 */ + char h_type; /* OMFS_INODE_X */ + u8 h_magic; /* OMFS_IMAGIC */ + u8 h_check_xor; /* XOR of header bytes before this */ + __be32 h_fill2; +}; + +Files and directories are both represented by omfs_inode: + +struct omfs_inode { + struct omfs_header i_head; /* header */ + __be64 i_parent; /* parent containing this inode */ + __be64 i_sibling; /* next inode in hash bucket */ + __be64 i_ctime; /* ctime, in milliseconds */ + char i_fill1[35]; + char i_type; /* OMFS_[DIR,FILE] */ + __be32 i_fill2; + char i_fill3[64]; + char i_name[OMFS_NAMELEN]; /* filename */ + __be64 i_size; /* size of file, in bytes */ +}; + +Directories in OMFS are implemented as a large hash table. Filenames are +hashed then prepended into the bucket list beginning at OMFS_DIR_START. +Lookup requires hashing the filename, then seeking across i_sibling pointers +until a match is found on i_name. Empty buckets are represented by block +pointers with all-1s (~0). + +A file is an omfs_inode structure followed by an extent table beginning at +OMFS_EXTENT_START: + +struct omfs_extent_entry { + __be64 e_cluster; /* start location of a set of blocks */ + __be64 e_blocks; /* number of blocks after e_cluster */ +}; + +struct omfs_extent { + __be64 e_next; /* next extent table location */ + __be32 e_extent_count; /* total # extents in this table */ + __be32 e_fill; + struct omfs_extent_entry e_entry; /* start of extent entries */ +}; + +Each extent holds the block offset followed by number of blocks allocated to +the extent. The final extent in each table is a terminator with e_cluster +being ~0 and e_blocks being ones'-complement of the total number of blocks +in the table. + +If this table overflows, a continuation inode is written and pointed to by +e_next. These have a header but lack the rest of the inode structure. + diff --git a/Documentation/filesystems/proc.txt b/Documentation/filesystems/proc.txt index 7f268f327d750e725f1e5ca5ddfe99dcb8014cd5..64557821ee5984f5babe336f701f172b8602a4dc 100644 --- a/Documentation/filesystems/proc.txt +++ b/Documentation/filesystems/proc.txt @@ -296,6 +296,7 @@ Table 1-4: Kernel info in /proc uptime System uptime version Kernel version video bttv info of video resources (2.4) + vmallocinfo Show vmalloced areas .............................................................................. You can, for example, check which interrupts are currently in use and what @@ -557,6 +558,49 @@ VmallocTotal: total size of vmalloc memory area VmallocUsed: amount of vmalloc area which is used VmallocChunk: largest contigious block of vmalloc area which is free +.............................................................................. + +vmallocinfo: + +Provides information about vmalloced/vmaped areas. One line per area, +containing the virtual address range of the area, size in bytes, +caller information of the creator, and optional information depending +on the kind of area : + + pages=nr number of pages + phys=addr if a physical address was specified + ioremap I/O mapping (ioremap() and friends) + vmalloc vmalloc() area + vmap vmap()ed pages + user VM_USERMAP area + vpages buffer for pages pointers was vmalloced (huge area) + N=nr (Only on NUMA kernels) + Number of pages allocated on memory node + +> cat /proc/vmallocinfo +0xffffc20000000000-0xffffc20000201000 2101248 alloc_large_system_hash+0x204 ... + /0x2c0 pages=512 vmalloc N0=128 N1=128 N2=128 N3=128 +0xffffc20000201000-0xffffc20000302000 1052672 alloc_large_system_hash+0x204 ... + /0x2c0 pages=256 vmalloc N0=64 N1=64 N2=64 N3=64 +0xffffc20000302000-0xffffc20000304000 8192 acpi_tb_verify_table+0x21/0x4f... + phys=7fee8000 ioremap +0xffffc20000304000-0xffffc20000307000 12288 acpi_tb_verify_table+0x21/0x4f... + phys=7fee7000 ioremap +0xffffc2000031d000-0xffffc2000031f000 8192 init_vdso_vars+0x112/0x210 +0xffffc2000031f000-0xffffc2000032b000 49152 cramfs_uncompress_init+0x2e ... + /0x80 pages=11 vmalloc N0=3 N1=3 N2=2 N3=3 +0xffffc2000033a000-0xffffc2000033d000 12288 sys_swapon+0x640/0xac0 ... + pages=2 vmalloc N1=2 +0xffffc20000347000-0xffffc2000034c000 20480 xt_alloc_table_info+0xfe ... + /0x130 [x_tables] pages=4 vmalloc N0=4 +0xffffffffa0000000-0xffffffffa000f000 61440 sys_init_module+0xc27/0x1d00 ... + pages=14 vmalloc N2=14 +0xffffffffa000f000-0xffffffffa0014000 20480 sys_init_module+0xc27/0x1d00 ... + pages=4 vmalloc N1=4 +0xffffffffa0014000-0xffffffffa0017000 12288 sys_init_module+0xc27/0x1d00 ... + pages=2 vmalloc N1=2 +0xffffffffa0017000-0xffffffffa0022000 45056 sys_init_module+0xc27/0x1d00 ... + pages=10 vmalloc N0=10 1.3 IDE devices in /proc/ide ---------------------------- @@ -887,7 +931,7 @@ group_prealloc max_to_scan mb_groups mb_history min_to_scan order2_req stats stream_req mb_groups: -This file gives the details of mutiblock allocator buddy cache of free blocks +This file gives the details of multiblock allocator buddy cache of free blocks mb_history: Multiblock allocation history. @@ -1430,7 +1474,7 @@ used because pages_free(1355) is smaller than watermark + protection[2] normal page requirement. If requirement is DMA zone(index=0), protection[0] (=0) is used. -zone[i]'s protection[j] is calculated by following exprssion. +zone[i]'s protection[j] is calculated by following expression. (i < j): zone[i]->protection[j] diff --git a/Documentation/filesystems/relay.txt b/Documentation/filesystems/relay.txt index 094f2d2f38b1a5571283ee745aa494c12b12808c..510b722667ac885cf7abed3732961941a5ad1c14 100644 --- a/Documentation/filesystems/relay.txt +++ b/Documentation/filesystems/relay.txt @@ -294,6 +294,16 @@ user-defined data with a channel, and is immediately available (including in create_buf_file()) via chan->private_data or buf->chan->private_data. +Buffer-only channels +-------------------- + +These channels have no files associated and can be created with +relay_open(NULL, NULL, ...). Such channels are useful in scenarios such +as when doing early tracing in the kernel, before the VFS is up. In these +cases, one may open a buffer-only channel and then call +relay_late_setup_files() when the kernel is ready to handle files, +to expose the buffered data to the userspace. + Channel 'modes' --------------- diff --git a/Documentation/filesystems/sysfs.txt b/Documentation/filesystems/sysfs.txt index 7f27b8f840d06210df1511db6ef603cedb8f0e58..9e9c348275a96fd362acf9916d2789be8a08c4c8 100644 --- a/Documentation/filesystems/sysfs.txt +++ b/Documentation/filesystems/sysfs.txt @@ -248,6 +248,7 @@ The top level sysfs directory looks like: block/ bus/ class/ +dev/ devices/ firmware/ net/ @@ -274,6 +275,11 @@ fs/ contains a directory for some filesystems. Currently each filesystem wanting to export attributes must create its own hierarchy below fs/ (see ./fuse.txt for an example). +dev/ contains two directories char/ and block/. Inside these two +directories there are symlinks named :. These symlinks +point to the sysfs directory for the given device. /sys/dev provides a +quick way to lookup the sysfs interface for a device from the result of +a stat(2) operation. More information can driver-model specific features can be found in Documentation/driver-model/. diff --git a/Documentation/filesystems/vfat.txt b/Documentation/filesystems/vfat.txt index 2d5e1e582e13272bfaef2fbc494a156d829cc289..bbac4f1d90567c3f7ea0f46a869c091160390076 100644 --- a/Documentation/filesystems/vfat.txt +++ b/Documentation/filesystems/vfat.txt @@ -96,6 +96,14 @@ shortname=lower|win95|winnt|mixed emulate the Windows 95 rule for create. Default setting is `lower'. +tz=UTC -- Interpret timestamps as UTC rather than local time. + This option disables the conversion of timestamps + between local time (as used by Windows on FAT) and UTC + (which Linux uses internally). This is particuluarly + useful when mounting devices (like digital cameras) + that are set to UTC in order to avoid the pitfalls of + local time. + : 0,1,yes,no,true,false TODO diff --git a/Documentation/filesystems/vfs.txt b/Documentation/filesystems/vfs.txt index b7522c6cbae3758f77cb12e22b78825e43a3796d..c4d348dabe9499454055ebff41fb88ef71346dda 100644 --- a/Documentation/filesystems/vfs.txt +++ b/Documentation/filesystems/vfs.txt @@ -143,7 +143,7 @@ struct file_system_type { The get_sb() method has the following arguments: - struct file_system_type *fs_type: decribes the filesystem, partly initialized + struct file_system_type *fs_type: describes the filesystem, partly initialized by the specific filesystem code int flags: mount flags @@ -895,9 +895,9 @@ struct dentry_operations { iput() yourself d_dname: called when the pathname of a dentry should be generated. - Usefull for some pseudo filesystems (sockfs, pipefs, ...) to delay + Useful for some pseudo filesystems (sockfs, pipefs, ...) to delay pathname generation. (Instead of doing it when dentry is created, - its done only when the path is needed.). Real filesystems probably + it's done only when the path is needed.). Real filesystems probably dont want to use it, because their dentries are present in global dcache hash, so their hash should be an invariant. As no lock is held, d_dname() should not try to modify the dentry itself, unless diff --git a/Documentation/gpio.txt b/Documentation/gpio.txt index c35ca9e40d4ca8ae0cbf7c06c639d8531ae8d9dd..18022e249c53dc1ad991d74d160551fa32f32070 100644 --- a/Documentation/gpio.txt +++ b/Documentation/gpio.txt @@ -347,15 +347,12 @@ necessarily be nonportable. Dynamic definition of GPIOs is not currently standard; for example, as a side effect of configuring an add-on board with some GPIO expanders. -These calls are purely for kernel space, but a userspace API could be built -on top of them. - GPIO implementor's framework (OPTIONAL) ======================================= As noted earlier, there is an optional implementation framework making it easier for platforms to support different kinds of GPIO controller using -the same programming interface. +the same programming interface. This framework is called "gpiolib". As a debugging aid, if debugfs is available a /sys/kernel/debug/gpio file will be found there. That will list all the controllers registered through @@ -392,11 +389,21 @@ either NULL or the label associated with that GPIO when it was requested. Platform Support ---------------- -To support this framework, a platform's Kconfig will "select HAVE_GPIO_LIB" +To support this framework, a platform's Kconfig will "select" either +ARCH_REQUIRE_GPIOLIB or ARCH_WANT_OPTIONAL_GPIOLIB and arrange that its includes and defines three functions: gpio_get_value(), gpio_set_value(), and gpio_cansleep(). They may also want to provide a custom value for ARCH_NR_GPIOS. +ARCH_REQUIRE_GPIOLIB means that the gpio-lib code will always get compiled +into the kernel on that architecture. + +ARCH_WANT_OPTIONAL_GPIOLIB means the gpio-lib code defaults to off and the user +can enable it and build it into the kernel optionally. + +If neither of these options are selected, the platform does not support +GPIOs through GPIO-lib and the code cannot be enabled by the user. + Trivial implementations of those functions can directly use framework code, which always dispatches through the gpio_chip: @@ -439,4 +446,120 @@ becomes available. That may mean the device should not be registered until calls for that GPIO can work. One way to address such dependencies is for such gpio_chip controllers to provide setup() and teardown() callbacks to board specific code; those board specific callbacks would register devices -once all the necessary resources are available. +once all the necessary resources are available, and remove them later when +the GPIO controller device becomes unavailable. + + +Sysfs Interface for Userspace (OPTIONAL) +======================================== +Platforms which use the "gpiolib" implementors framework may choose to +configure a sysfs user interface to GPIOs. This is different from the +debugfs interface, since it provides control over GPIO direction and +value instead of just showing a gpio state summary. Plus, it could be +present on production systems without debugging support. + +Given approprate hardware documentation for the system, userspace could +know for example that GPIO #23 controls the write protect line used to +protect boot loader segments in flash memory. System upgrade procedures +may need to temporarily remove that protection, first importing a GPIO, +then changing its output state, then updating the code before re-enabling +the write protection. In normal use, GPIO #23 would never be touched, +and the kernel would have no need to know about it. + +Again depending on appropriate hardware documentation, on some systems +userspace GPIO can be used to determine system configuration data that +standard kernels won't know about. And for some tasks, simple userspace +GPIO drivers could be all that the system really needs. + +Note that standard kernel drivers exist for common "LEDs and Buttons" +GPIO tasks: "leds-gpio" and "gpio_keys", respectively. Use those +instead of talking directly to the GPIOs; they integrate with kernel +frameworks better than your userspace code could. + + +Paths in Sysfs +-------------- +There are three kinds of entry in /sys/class/gpio: + + - Control interfaces used to get userspace control over GPIOs; + + - GPIOs themselves; and + + - GPIO controllers ("gpio_chip" instances). + +That's in addition to standard files including the "device" symlink. + +The control interfaces are write-only: + + /sys/class/gpio/ + + "export" ... Userspace may ask the kernel to export control of + a GPIO to userspace by writing its number to this file. + + Example: "echo 19 > export" will create a "gpio19" node + for GPIO #19, if that's not requested by kernel code. + + "unexport" ... Reverses the effect of exporting to userspace. + + Example: "echo 19 > unexport" will remove a "gpio19" + node exported using the "export" file. + +GPIO signals have paths like /sys/class/gpio/gpio42/ (for GPIO #42) +and have the following read/write attributes: + + /sys/class/gpio/gpioN/ + + "direction" ... reads as either "in" or "out". This value may + normally be written. Writing as "out" defaults to + initializing the value as low. To ensure glitch free + operation, values "low" and "high" may be written to + configure the GPIO as an output with that initial value. + + Note that this attribute *will not exist* if the kernel + doesn't support changing the direction of a GPIO, or + it was exported by kernel code that didn't explicitly + allow userspace to reconfigure this GPIO's direction. + + "value" ... reads as either 0 (low) or 1 (high). If the GPIO + is configured as an output, this value may be written; + any nonzero value is treated as high. + +GPIO controllers have paths like /sys/class/gpio/chipchip42/ (for the +controller implementing GPIOs starting at #42) and have the following +read-only attributes: + + /sys/class/gpio/gpiochipN/ + + "base" ... same as N, the first GPIO managed by this chip + + "label" ... provided for diagnostics (not always unique) + + "ngpio" ... how many GPIOs this manges (N to N + ngpio - 1) + +Board documentation should in most cases cover what GPIOs are used for +what purposes. However, those numbers are not always stable; GPIOs on +a daughtercard might be different depending on the base board being used, +or other cards in the stack. In such cases, you may need to use the +gpiochip nodes (possibly in conjunction with schematics) to determine +the correct GPIO number to use for a given signal. + + +Exporting from Kernel code +-------------------------- +Kernel code can explicitly manage exports of GPIOs which have already been +requested using gpio_request(): + + /* export the GPIO to userspace */ + int gpio_export(unsigned gpio, bool direction_may_change); + + /* reverse gpio_export() */ + void gpio_unexport(); + +After a kernel driver requests a GPIO, it may only be made available in +the sysfs interface by gpio_export(). The driver can control whether the +signal direction may change. This helps drivers prevent userspace code +from accidentally clobbering important system state. + +This explicit exporting can help with debugging (by making some kinds +of experiments easier), or can provide an always-there interface that's +suitable for documenting as part of a board support package. diff --git a/Documentation/i2c/upgrading-clients b/Documentation/i2c/upgrading-clients new file mode 100644 index 0000000000000000000000000000000000000000..9a45f9bb6a255d421bd2903e69120c0a8e281017 --- /dev/null +++ b/Documentation/i2c/upgrading-clients @@ -0,0 +1,281 @@ +Upgrading I2C Drivers to the new 2.6 Driver Model +================================================= + +Ben Dooks + +Introduction +------------ + +This guide outlines how to alter existing Linux 2.6 client drivers from +the old to the new new binding methods. + + +Example old-style driver +------------------------ + + +struct example_state { + struct i2c_client client; + .... +}; + +static struct i2c_driver example_driver; + +static unsigned short ignore[] = { I2C_CLIENT_END }; +static unsigned short normal_addr[] = { OUR_ADDR, I2C_CLIENT_END }; + +I2C_CLIENT_INSMOD; + +static int example_attach(struct i2c_adapter *adap, int addr, int kind) +{ + struct example_state *state; + struct device *dev = &adap->dev; /* to use for dev_ reports */ + int ret; + + state = kzalloc(sizeof(struct example_state), GFP_KERNEL); + if (state == NULL) { + dev_err(dev, "failed to create our state\n"); + return -ENOMEM; + } + + example->client.addr = addr; + example->client.flags = 0; + example->client.adapter = adap; + + i2c_set_clientdata(&state->i2c_client, state); + strlcpy(client->i2c_client.name, "example", I2C_NAME_SIZE); + + ret = i2c_attach_client(&state->i2c_client); + if (ret < 0) { + dev_err(dev, "failed to attach client\n"); + kfree(state); + return ret; + } + + dev = &state->i2c_client.dev; + + /* rest of the initialisation goes here. */ + + dev_info(dev, "example client created\n"); + + return 0; +} + +static int __devexit example_detach(struct i2c_client *client) +{ + struct example_state *state = i2c_get_clientdata(client); + + i2c_detach_client(client); + kfree(state); + return 0; +} + +static int example_attach_adapter(struct i2c_adapter *adap) +{ + return i2c_probe(adap, &addr_data, example_attach); +} + +static struct i2c_driver example_driver = { + .driver = { + .owner = THIS_MODULE, + .name = "example", + }, + .attach_adapter = example_attach_adapter, + .detach_client = __devexit_p(example_detach), + .suspend = example_suspend, + .resume = example_resume, +}; + + +Updating the client +------------------- + +The new style binding model will check against a list of supported +devices and their associated address supplied by the code registering +the busses. This means that the driver .attach_adapter and +.detach_adapter methods can be removed, along with the addr_data, +as follows: + +- static struct i2c_driver example_driver; + +- static unsigned short ignore[] = { I2C_CLIENT_END }; +- static unsigned short normal_addr[] = { OUR_ADDR, I2C_CLIENT_END }; + +- I2C_CLIENT_INSMOD; + +- static int example_attach_adapter(struct i2c_adapter *adap) +- { +- return i2c_probe(adap, &addr_data, example_attach); +- } + + static struct i2c_driver example_driver = { +- .attach_adapter = example_attach_adapter, +- .detach_client = __devexit_p(example_detach), + } + +Add the probe and remove methods to the i2c_driver, as so: + + static struct i2c_driver example_driver = { ++ .probe = example_probe, ++ .remove = __devexit_p(example_remove), + } + +Change the example_attach method to accept the new parameters +which include the i2c_client that it will be working with: + +- static int example_attach(struct i2c_adapter *adap, int addr, int kind) ++ static int example_probe(struct i2c_client *client, ++ const struct i2c_device_id *id) + +Change the name of example_attach to example_probe to align it with the +i2c_driver entry names. The rest of the probe routine will now need to be +changed as the i2c_client has already been setup for use. + +The necessary client fields have already been setup before +the probe function is called, so the following client setup +can be removed: + +- example->client.addr = addr; +- example->client.flags = 0; +- example->client.adapter = adap; +- +- strlcpy(client->i2c_client.name, "example", I2C_NAME_SIZE); + +The i2c_set_clientdata is now: + +- i2c_set_clientdata(&state->client, state); ++ i2c_set_clientdata(client, state); + +The call to i2c_attach_client is no longer needed, if the probe +routine exits successfully, then the driver will be automatically +attached by the core. Change the probe routine as so: + +- ret = i2c_attach_client(&state->i2c_client); +- if (ret < 0) { +- dev_err(dev, "failed to attach client\n"); +- kfree(state); +- return ret; +- } + + +Remove the storage of 'struct i2c_client' from the 'struct example_state' +as we are provided with the i2c_client in our example_probe. Instead we +store a pointer to it for when it is needed. + +struct example_state { +- struct i2c_client client; ++ struct i2c_client *client; + +the new i2c client as so: + +- struct device *dev = &adap->dev; /* to use for dev_ reports */ ++ struct device *dev = &i2c_client->dev; /* to use for dev_ reports */ + +And remove the change after our client is attached, as the driver no +longer needs to register a new client structure with the core: + +- dev = &state->i2c_client.dev; + +In the probe routine, ensure that the new state has the client stored +in it: + +static int example_probe(struct i2c_client *i2c_client, + const struct i2c_device_id *id) +{ + struct example_state *state; + struct device *dev = &i2c_client->dev; + int ret; + + state = kzalloc(sizeof(struct example_state), GFP_KERNEL); + if (state == NULL) { + dev_err(dev, "failed to create our state\n"); + return -ENOMEM; + } + ++ state->client = i2c_client; + +Update the detach method, by changing the name to _remove and +to delete the i2c_detach_client call. It is possible that you +can also remove the ret variable as it is not not needed for +any of the core functions. + +- static int __devexit example_detach(struct i2c_client *client) ++ static int __devexit example_remove(struct i2c_client *client) +{ + struct example_state *state = i2c_get_clientdata(client); + +- i2c_detach_client(client); + +And finally ensure that we have the correct ID table for the i2c-core +and other utilities: + ++ struct i2c_device_id example_idtable[] = { ++ { "example", 0 }, ++ { } ++}; ++ ++MODULE_DEVICE_TABLE(i2c, example_idtable); + +static struct i2c_driver example_driver = { + .driver = { + .owner = THIS_MODULE, + .name = "example", + }, ++ .id_table = example_ids, + + +Our driver should now look like this: + +struct example_state { + struct i2c_client *client; + .... +}; + +static int example_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct example_state *state; + struct device *dev = &client->dev; + + state = kzalloc(sizeof(struct example_state), GFP_KERNEL); + if (state == NULL) { + dev_err(dev, "failed to create our state\n"); + return -ENOMEM; + } + + state->client = client; + i2c_set_clientdata(client, state); + + /* rest of the initialisation goes here. */ + + dev_info(dev, "example client created\n"); + + return 0; +} + +static int __devexit example_remove(struct i2c_client *client) +{ + struct example_state *state = i2c_get_clientdata(client); + + kfree(state); + return 0; +} + +static struct i2c_device_id example_idtable[] = { + { "example", 0 }, + { } +}; + +MODULE_DEVICE_TABLE(i2c, example_idtable); + +static struct i2c_driver example_driver = { + .driver = { + .owner = THIS_MODULE, + .name = "example", + }, + .id_table = example_idtable, + .probe = example_probe, + .remove = __devexit_p(example_remove), + .suspend = example_suspend, + .resume = example_resume, +}; diff --git a/Documentation/ia64/kvm.txt b/Documentation/ia64/kvm.txt index bec9d815da33a0495c7ea4d2eebecf7f4c1ab2fc..914d07f49268b728ab5c1d8a6e7b23b59cef0128 100644 --- a/Documentation/ia64/kvm.txt +++ b/Documentation/ia64/kvm.txt @@ -50,9 +50,9 @@ Note: For step 2, please make sure that host page size == TARGET_PAGE_SIZE of qe /usr/local/bin/qemu-system-ia64 -smp xx -m 512 -hda $your_image (xx is the number of virtual processors for the guest, now the maximum value is 4) -5. Known possibile issue on some platforms with old Firmware. +5. Known possible issue on some platforms with old Firmware. -If meet strange host crashe issues, try to solve it through either of the following ways: +In the event of strange host crash issues, try to solve it through either of the following ways: (1): Upgrade your Firmware to the latest one. @@ -65,8 +65,8 @@ index 0b53344..f02b0f7 100644 mov ar.pfs = loc1 mov rp = loc0 ;; -- srlz.d // seralize restoration of psr.l -+ srlz.i // seralize restoration of psr.l +- srlz.d // serialize restoration of psr.l ++ srlz.i // serialize restoration of psr.l + ;; br.ret.sptk.many b0 END(ia64_pal_call_static) diff --git a/Documentation/ia64/paravirt_ops.txt b/Documentation/ia64/paravirt_ops.txt new file mode 100644 index 0000000000000000000000000000000000000000..39ded02ec33fc8a06c3e09d34ad1760d9e417b08 --- /dev/null +++ b/Documentation/ia64/paravirt_ops.txt @@ -0,0 +1,137 @@ +Paravirt_ops on IA64 +==================== + 21 May 2008, Isaku Yamahata + + +Introduction +------------ +The aim of this documentation is to help with maintainability and/or to +encourage people to use paravirt_ops/IA64. + +paravirt_ops (pv_ops in short) is a way for virtualization support of +Linux kernel on x86. Several ways for virtualization support were +proposed, paravirt_ops is the winner. +On the other hand, now there are also several IA64 virtualization +technologies like kvm/IA64, xen/IA64 and many other academic IA64 +hypervisors so that it is good to add generic virtualization +infrastructure on Linux/IA64. + + +What is paravirt_ops? +--------------------- +It has been developed on x86 as virtualization support via API, not ABI. +It allows each hypervisor to override operations which are important for +hypervisors at API level. And it allows a single kernel binary to run on +all supported execution environments including native machine. +Essentially paravirt_ops is a set of function pointers which represent +operations corresponding to low level sensitive instructions and high +level functionalities in various area. But one significant difference +from usual function pointer table is that it allows optimization with +binary patch. It is because some of these operations are very +performance sensitive and indirect call overhead is not negligible. +With binary patch, indirect C function call can be transformed into +direct C function call or in-place execution to eliminate the overhead. + +Thus, operations of paravirt_ops are classified into three categories. +- simple indirect call + These operations correspond to high level functionality so that the + overhead of indirect call isn't very important. + +- indirect call which allows optimization with binary patch + Usually these operations correspond to low level instructions. They + are called frequently and performance critical. So the overhead is + very important. + +- a set of macros for hand written assembly code + Hand written assembly codes (.S files) also need paravirtualization + because they include sensitive instructions or some of code paths in + them are very performance critical. + + +The relation to the IA64 machine vector +--------------------------------------- +Linux/IA64 has the IA64 machine vector functionality which allows the +kernel to switch implementations (e.g. initialization, ipi, dma api...) +depending on executing platform. +We can replace some implementations very easily defining a new machine +vector. Thus another approach for virtualization support would be +enhancing the machine vector functionality. +But paravirt_ops approach was taken because +- virtualization support needs wider support than machine vector does. + e.g. low level instruction paravirtualization. It must be + initialized very early before platform detection. + +- virtualization support needs more functionality like binary patch. + Probably the calling overhead might not be very large compared to the + emulation overhead of virtualization. However in the native case, the + overhead should be eliminated completely. + A single kernel binary should run on each environment including native, + and the overhead of paravirt_ops on native environment should be as + small as possible. + +- for full virtualization technology, e.g. KVM/IA64 or + Xen/IA64 HVM domain, the result would be + (the emulated platform machine vector. probably dig) + (pv_ops). + This means that the virtualization support layer should be under + the machine vector layer. + +Possibly it might be better to move some function pointers from +paravirt_ops to machine vector. In fact, Xen domU case utilizes both +pv_ops and machine vector. + + +IA64 paravirt_ops +----------------- +In this section, the concrete paravirt_ops will be discussed. +Because of the architecture difference between ia64 and x86, the +resulting set of functions is very different from x86 pv_ops. + +- C function pointer tables +They are not very performance critical so that simple C indirect +function call is acceptable. The following structures are defined at +this moment. For details see linux/include/asm-ia64/paravirt.h + - struct pv_info + This structure describes the execution environment. + - struct pv_init_ops + This structure describes the various initialization hooks. + - struct pv_iosapic_ops + This structure describes hooks to iosapic operations. + - struct pv_irq_ops + This structure describes hooks to irq related operations + - struct pv_time_op + This structure describes hooks to steal time accounting. + +- a set of indirect calls which need optimization +Currently this class of functions correspond to a subset of IA64 +intrinsics. At this moment the optimization with binary patch isn't +implemented yet. +struct pv_cpu_op is defined. For details see +linux/include/asm-ia64/paravirt_privop.h +Mostly they correspond to ia64 intrinsics 1-to-1. +Caveat: Now they are defined as C indirect function pointers, but in +order to support binary patch optimization, they will be changed +using GCC extended inline assembly code. + +- a set of macros for hand written assembly code (.S files) +For maintenance purpose, the taken approach for .S files is single +source code and compile multiple times with different macros definitions. +Each pv_ops instance must define those macros to compile. +The important thing here is that sensitive, but non-privileged +instructions must be paravirtualized and that some privileged +instructions also need paravirtualization for reasonable performance. +Developers who modify .S files must be aware of that. At this moment +an easy checker is implemented to detect paravirtualization breakage. +But it doesn't cover all the cases. + +Sometimes this set of macros is called pv_cpu_asm_op. But there is no +corresponding structure in the source code. +Those macros mostly 1:1 correspond to a subset of privileged +instructions. See linux/include/asm-ia64/native/inst.h. +And some functions written in assembly also need to be overrided so +that each pv_ops instance have to define some macros. Again see +linux/include/asm-ia64/native/inst.h. + + +Those structures must be initialized very early before start_kernel. +Probably initialized in head.S using multi entry point or some other trick. +For native case implementation see linux/arch/ia64/kernel/paravirt.c. diff --git a/Documentation/input/cs461x.txt b/Documentation/input/cs461x.txt index afe0d6543e093fa5dfa4758bbb0cbec90ff0bce3..202e9dbacec39a96990c5722c4b1ab832b939b61 100644 --- a/Documentation/input/cs461x.txt +++ b/Documentation/input/cs461x.txt @@ -31,7 +31,7 @@ The driver works with ALSA drivers simultaneously. For example, the xracer uses joystick as input device and PCM device as sound output in one time. There are no sound or input collisions detected. The source code have comments about them; but I've found the joystick can be initialized -separately of ALSA modules. So, you canm use only one joystick driver +separately of ALSA modules. So, you can use only one joystick driver without ALSA drivers. The ALSA drivers are not needed to compile or run this driver. diff --git a/Documentation/input/gameport-programming.txt b/Documentation/input/gameport-programming.txt index 14e0a8b70225f5cce93c2cf8bdb85a0aa984b8ee..03a74fc3b49679c0326a59faa43b2e423751e0c5 100644 --- a/Documentation/input/gameport-programming.txt +++ b/Documentation/input/gameport-programming.txt @@ -1,5 +1,3 @@ -$Id: gameport-programming.txt,v 1.3 2001/04/24 13:51:37 vojtech Exp $ - Programming gameport drivers ~~~~~~~~~~~~~~~~~~~~~~~~~~~~ diff --git a/Documentation/input/input.txt b/Documentation/input/input.txt index ff8cea0225f90bdce6c28adc5b3af5816f9eea44..686ee9932dffd86fa78775859a97815ecc514be2 100644 --- a/Documentation/input/input.txt +++ b/Documentation/input/input.txt @@ -1,7 +1,6 @@ Linux Input drivers v1.0 (c) 1999-2001 Vojtech Pavlik Sponsored by SuSE - $Id: input.txt,v 1.8 2002/05/29 03:15:01 bradleym Exp $ ---------------------------------------------------------------------------- 0. Disclaimer diff --git a/Documentation/input/joystick-api.txt b/Documentation/input/joystick-api.txt index acbd32b88454dc5c48c7a10bb112757910d3c7e5..c507330740cd4fb14e37e617d01d95262057d129 100644 --- a/Documentation/input/joystick-api.txt +++ b/Documentation/input/joystick-api.txt @@ -5,8 +5,6 @@ 7 Aug 1998 - $Id: joystick-api.txt,v 1.2 2001/05/08 21:21:23 vojtech Exp $ - 1. Initialization ~~~~~~~~~~~~~~~~~ diff --git a/Documentation/input/joystick-parport.txt b/Documentation/input/joystick-parport.txt index ede5f33daad3dbc0f7346654a348fd4eb28d7387..1c856f32ff2c3bc880746533c149ec6cc146806f 100644 --- a/Documentation/input/joystick-parport.txt +++ b/Documentation/input/joystick-parport.txt @@ -2,7 +2,6 @@ (c) 1998-2000 Vojtech Pavlik (c) 1998 Andree Borrmann Sponsored by SuSE - $Id: joystick-parport.txt,v 1.6 2001/09/25 09:31:32 vojtech Exp $ ---------------------------------------------------------------------------- 0. Disclaimer diff --git a/Documentation/input/joystick.txt b/Documentation/input/joystick.txt index 389de9bd987894017bb25ddc95b911c98526bdcb..154d767b2acbc4be459044d78e7f63b975faa207 100644 --- a/Documentation/input/joystick.txt +++ b/Documentation/input/joystick.txt @@ -1,7 +1,6 @@ Linux Joystick driver v2.0.0 (c) 1996-2000 Vojtech Pavlik Sponsored by SuSE - $Id: joystick.txt,v 1.12 2002/03/03 12:13:07 jdeneux Exp $ ---------------------------------------------------------------------------- 0. Disclaimer diff --git a/Documentation/ioctl/ioctl-decoding.txt b/Documentation/ioctl/ioctl-decoding.txt index bfdf7f3ee4f05e0f52e08c8aee1ad55c248b8af4..e35efb0cec2e64a99538d24c2c7c7b38846abc26 100644 --- a/Documentation/ioctl/ioctl-decoding.txt +++ b/Documentation/ioctl/ioctl-decoding.txt @@ -1,6 +1,6 @@ To decode a hex IOCTL code: -Most architecures use this generic format, but check +Most architectures use this generic format, but check include/ARCH/ioctl.h for specifics, e.g. powerpc uses 3 bits to encode read/write and 13 bits for size. @@ -18,7 +18,7 @@ uses 3 bits to encode read/write and 13 bits for size. 7-0 function # - So for example 0x82187201 is a read with arg length of 0x218, +So for example 0x82187201 is a read with arg length of 0x218, character 'r' function 1. Grepping the source reveals this is: #define VFAT_IOCTL_READDIR_BOTH _IOR('r', 1, struct dirent [2]) diff --git a/Documentation/iostats.txt b/Documentation/iostats.txt index 5925c3cd030d55884b3f962ed40ced5a20709cf4..59a69ec67c408a54ee724df4d4a64a69a8317f68 100644 --- a/Documentation/iostats.txt +++ b/Documentation/iostats.txt @@ -143,7 +143,7 @@ disk and partition statistics are consistent again. Since we still don't keep record of the partition-relative address, an operation is attributed to the partition which contains the first sector of the request after the eventual merges. As requests can be merged across partition, this could lead -to some (probably insignificant) innacuracy. +to some (probably insignificant) inaccuracy. Additional notes ---------------- diff --git a/Documentation/isdn/README.mISDN b/Documentation/isdn/README.mISDN new file mode 100644 index 0000000000000000000000000000000000000000..cd8bf920e77bcac0ec8d4068db18441bd28083d5 --- /dev/null +++ b/Documentation/isdn/README.mISDN @@ -0,0 +1,6 @@ +mISDN is a new modular ISDN driver, in the long term it should replace +the old I4L driver architecture for passiv ISDN cards. +It was designed to allow a broad range of applications and interfaces +but only have the basic function in kernel, the interface to the user +space is based on sockets with a own address family AF_ISDN. + diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 09ad7450647bc81dff32a3eaf7ea3c0858f4a896..e7bea3e853044e54f3ee863ad3d295b0df84a522 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -87,7 +87,8 @@ parameter is applicable: SH SuperH architecture is enabled. SMP The kernel is an SMP kernel. SPARC Sparc architecture is enabled. - SWSUSP Software suspend is enabled. + SWSUSP Software suspend (hibernation) is enabled. + SUSPEND System suspend states are enabled. TS Appropriate touchscreen support is enabled. USB USB support is enabled. USBHID USB Human Interface Device support is enabled. @@ -147,10 +148,12 @@ and is between 256 and 4096 characters. It is defined in the file default: 0 acpi_sleep= [HW,ACPI] Sleep options - Format: { s3_bios, s3_mode, s3_beep, old_ordering } + Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig, old_ordering } See Documentation/power/video.txt for s3_bios and s3_mode. s3_beep is for debugging; it makes the PC's speaker beep as soon as the kernel's real-mode entry point is called. + s4_nohwsig prevents ACPI hardware signature from being + used during resume from hibernation. old_ordering causes the ACPI 1.0 ordering of the _PTS control method, wrt putting devices into low power states, to be enforced (the ACPI 2.0 ordering of _PTS is @@ -774,8 +777,22 @@ and is between 256 and 4096 characters. It is defined in the file hisax= [HW,ISDN] See Documentation/isdn/README.HiSax. - hugepages= [HW,X86-32,IA-64] Maximal number of HugeTLB pages. - hugepagesz= [HW,IA-64,PPC] The size of the HugeTLB pages. + hugepages= [HW,X86-32,IA-64] HugeTLB pages to allocate at boot. + hugepagesz= [HW,IA-64,PPC,X86-64] The size of the HugeTLB pages. + On x86-64 and powerpc, this option can be specified + multiple times interleaved with hugepages= to reserve + huge pages of different sizes. Valid pages sizes on + x86-64 are 2M (when the CPU supports "pse") and 1G + (when the CPU supports the "pdpe1gb" cpuinfo flag) + Note that 1GB pages can only be allocated at boot time + using hugepages= and not freed afterwards. + default_hugepagesz= + [same as hugepagesz=] The size of the default + HugeTLB page size. This is the size represented by + the legacy /proc/ hugepages APIs, used for SHM, and + default size when mounting hugetlbfs filesystems. + Defaults to the default architecture's huge page size + if not specified. i8042.direct [HW] Put keyboard port into non-translated mode i8042.dumbkbd [HW] Pretend that controller can only read data from @@ -1206,7 +1223,7 @@ and is between 256 and 4096 characters. It is defined in the file or memmap=0x10000$0x18690000 - memtest= [KNL,X86_64] Enable memtest + memtest= [KNL,X86] Enable memtest Format: range: 0,4 : pattern number default : 0 @@ -1225,6 +1242,14 @@ and is between 256 and 4096 characters. It is defined in the file mga= [HW,DRM] + mminit_loglevel= + [KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this + parameter allows control of the logging verbosity for + the additional memory initialisation checks. A value + of 0 disables mminit logging and a level of 4 will + log everything. Information is printed at KERN_DEBUG + so loglevel=8 may also need to be specified. + mousedev.tap_time= [MOUSE] Maximum time between finger touching and leaving touchpad surface for touch to be considered @@ -1279,6 +1304,13 @@ and is between 256 and 4096 characters. It is defined in the file This usage is only documented in each driver source file if at all. + nf_conntrack.acct= + [NETFILTER] Enable connection tracking flow accounting + 0 to disable accounting + 1 to enable accounting + Default value depends on CONFIG_NF_CT_ACCT that is + going to be removed in 2.6.29. + nfsaddrs= [NFS] See Documentation/filesystems/nfsroot.txt. @@ -2027,6 +2059,9 @@ and is between 256 and 4096 characters. It is defined in the file snd-ymfpci= [HW,ALSA] + softlockup_panic= + [KNL] Should the soft-lockup detector generate panics. + sonypi.*= [HW] Sony Programmable I/O Control Device driver See Documentation/sonypi.txt @@ -2091,6 +2126,12 @@ and is between 256 and 4096 characters. It is defined in the file tdfx= [HW,DRM] + test_suspend= [SUSPEND] + Specify "mem" (for Suspend-to-RAM) or "standby" (for + standby suspend) as the system sleep state to briefly + enter during system startup. The system is woken from + this state using a wakeup-capable RTC alarm. + thash_entries= [KNL,NET] Set number of hash buckets for TCP connection @@ -2118,13 +2159,6 @@ and is between 256 and 4096 characters. It is defined in the file : poll all this frequency 0: no polling (default) - tipar.timeout= [HW,PPT] - Set communications timeout in tenths of a second - (default 15). - - tipar.delay= [HW,PPT] - Set inter-bit delay in microseconds (default 10). - tmscsim= [HW,SCSI] See comment before function dc390_setup() in drivers/scsi/tmscsim.c. @@ -2158,6 +2192,10 @@ and is between 256 and 4096 characters. It is defined in the file Note that genuine overcurrent events won't be reported either. + unknown_nmi_panic + [X86-32,X86-64] + Set unknown_nmi_panic=1 early on boot. + usbcore.autosuspend= [USB] The autosuspend time delay (in seconds) used for newly-detected USB devices (default 2). This diff --git a/Documentation/keys.txt b/Documentation/keys.txt index d5c7a57d17007fa0f43558b270b0e4c302d5f8aa..b56aacc1fff864022dbdf67aac997d54f0d14f32 100644 --- a/Documentation/keys.txt +++ b/Documentation/keys.txt @@ -864,7 +864,7 @@ payload contents" for more information. request_key_with_auxdata() respectively. These two functions return with the key potentially still under - construction. To wait for contruction completion, the following should be + construction. To wait for construction completion, the following should be called: int wait_for_key_construction(struct key *key, bool intr); diff --git a/Documentation/laptops/thinkpad-acpi.txt b/Documentation/laptops/thinkpad-acpi.txt index 64b3f146e4b09aa4d2cd312e97689f9eba503347..02dc748b76c4ac861549077392ef1deb3ca9c652 100644 --- a/Documentation/laptops/thinkpad-acpi.txt +++ b/Documentation/laptops/thinkpad-acpi.txt @@ -1,7 +1,7 @@ ThinkPad ACPI Extras Driver - Version 0.20 - April 09th, 2008 + Version 0.21 + May 29th, 2008 Borislav Deianov Henrique de Moraes Holschuh @@ -621,7 +621,8 @@ Bluetooth --------- procfs: /proc/acpi/ibm/bluetooth -sysfs device attribute: bluetooth_enable +sysfs device attribute: bluetooth_enable (deprecated) +sysfs rfkill class: switch "tpacpi_bluetooth_sw" This feature shows the presence and current state of a ThinkPad Bluetooth device in the internal ThinkPad CDC slot. @@ -643,8 +644,12 @@ Sysfs notes: 0: disables Bluetooth / Bluetooth is disabled 1: enables Bluetooth / Bluetooth is enabled. - Note: this interface will be probably be superseded by the - generic rfkill class, so it is NOT to be considered stable yet. + Note: this interface has been superseded by the generic rfkill + class. It has been deprecated, and it will be removed in year + 2010. + + rfkill controller switch "tpacpi_bluetooth_sw": refer to + Documentation/rfkill.txt for details. Video output control -- /proc/acpi/ibm/video -------------------------------------------- @@ -1374,7 +1379,8 @@ EXPERIMENTAL: WAN ----------------- procfs: /proc/acpi/ibm/wan -sysfs device attribute: wwan_enable +sysfs device attribute: wwan_enable (deprecated) +sysfs rfkill class: switch "tpacpi_wwan_sw" This feature is marked EXPERIMENTAL because the implementation directly accesses hardware registers and may not work as expected. USE @@ -1404,8 +1410,12 @@ Sysfs notes: 0: disables WWAN card / WWAN card is disabled 1: enables WWAN card / WWAN card is enabled. - Note: this interface will be probably be superseded by the - generic rfkill class, so it is NOT to be considered stable yet. + Note: this interface has been superseded by the generic rfkill + class. It has been deprecated, and it will be removed in year + 2010. + + rfkill controller switch "tpacpi_wwan_sw": refer to + Documentation/rfkill.txt for details. Multiple Commands, Module Parameters ------------------------------------ diff --git a/Documentation/leds-class.txt b/Documentation/leds-class.txt index 18860ad9935a7876746c00660f36b9fd90529499..6399557cdab3d6542a0feea0c0cd2c6b2af5ffad 100644 --- a/Documentation/leds-class.txt +++ b/Documentation/leds-class.txt @@ -59,7 +59,7 @@ Hardware accelerated blink of LEDs Some LEDs can be programmed to blink without any CPU interaction. To support this feature, a LED driver can optionally implement the -blink_set() function (see ). If implemeted, triggers can +blink_set() function (see ). If implemented, triggers can attempt to use it before falling back to software timers. The blink_set() function should return 0 if the blink setting is supported, or -EINVAL otherwise, which means that LED blinking will be handled by software. diff --git a/Documentation/local_ops.txt b/Documentation/local_ops.txt index 4269a1105b378fafcc689435a2531b9d9d4287db..f4f8b1c6c8ba45ba6ec351aa92c40e798024983c 100644 --- a/Documentation/local_ops.txt +++ b/Documentation/local_ops.txt @@ -36,7 +36,7 @@ It can be done by slightly modifying the standard atomic operations : only their UP variant must be kept. It typically means removing LOCK prefix (on i386 and x86_64) and any SMP sychronization barrier. If the architecture does not have a different behavior between SMP and UP, including asm-generic/local.h -in your archtecture's local.h is sufficient. +in your architecture's local.h is sufficient. The local_t type is defined as an opaque signed long by embedding an atomic_long_t inside a structure. This is made so a cast from this type to a diff --git a/Documentation/md.txt b/Documentation/md.txt index a8b430627473aa243995ab6f6e173b9cf1ff819e..1da9d1b1793f3436b3561a48de7fbcd8c893e74e 100644 --- a/Documentation/md.txt +++ b/Documentation/md.txt @@ -236,6 +236,11 @@ All md devices contain: writing the word for the desired state, however some states cannot be explicitly set, and some transitions are not allowed. + Select/poll works on this file. All changes except between + active_idle and active (which can be frequent and are not + very interesting) are notified. active->active_idle is + reported if the metadata is externally managed. + clear No devices, no size, no level Writing is equivalent to STOP_ARRAY ioctl @@ -292,6 +297,10 @@ Each directory contains: writemostly - device will only be subject to read requests if there are no other options. This applies only to raid1 arrays. + blocked - device has failed, metadata is "external", + and the failure hasn't been acknowledged yet. + Writes that would write to this device if + it were not faulty are blocked. spare - device is working, but not a full member. This includes spares that are in the process of being recovered to @@ -301,6 +310,12 @@ Each directory contains: Writing "remove" removes the device from the array. Writing "writemostly" sets the writemostly flag. Writing "-writemostly" clears the writemostly flag. + Writing "blocked" sets the "blocked" flag. + Writing "-blocked" clear the "blocked" flag and allows writes + to complete. + + This file responds to select/poll. Any change to 'faulty' + or 'blocked' causes an event. errors An approximate count of read errors that have been detected on @@ -332,7 +347,7 @@ Each directory contains: for storage of data. This will normally be the same as the component_size. This can be written while assembling an array. If a value less than the current component_size is - written, component_size will be reduced to this value. + written, it will be rejected. An active md device will also contain and entry for each active device @@ -381,6 +396,19 @@ also have 'check' and 'repair' will start the appropriate process providing the current state is 'idle'. + This file responds to select/poll. Any important change in the value + triggers a poll event. Sometimes the value will briefly be + "recover" if a recovery seems to be needed, but cannot be + achieved. In that case, the transition to "recover" isn't + notified, but the transition away is. + + degraded + This contains a count of the number of devices by which the + arrays is degraded. So an optimal array with show '0'. A + single failed/missing drive will show '1', etc. + This file responds to select/poll, any increase or decrease + in the count of missing devices will trigger an event. + mismatch_count When performing 'check' and 'repair', and possibly when performing 'resync', md will count the number of errors that are diff --git a/Documentation/moxa-smartio b/Documentation/moxa-smartio index fe24ecc6372e6b3482c3f39972ab9f70077d7b70..5337e80a5b96c6341e523394be6fedc58b87f6ed 100644 --- a/Documentation/moxa-smartio +++ b/Documentation/moxa-smartio @@ -1,14 +1,22 @@ ============================================================================= - - MOXA Smartio Family Device Driver Ver 1.1 Installation Guide - for Linux Kernel 2.2.x and 2.0.3x - Copyright (C) 1999, Moxa Technologies Co, Ltd. + MOXA Smartio/Industio Family Device Driver Installation Guide + for Linux Kernel 2.4.x, 2.6.x + Copyright (C) 2008, Moxa Inc. ============================================================================= +Date: 01/21/2008 + Content 1. Introduction 2. System Requirement 3. Installation + 3.1 Hardware installation + 3.2 Driver files + 3.3 Device naming convention + 3.4 Module driver configuration + 3.5 Static driver configuration for Linux kernel 2.4.x and 2.6.x. + 3.6 Custom configuration + 3.7 Verify driver installation 4. Utilities 5. Setserial 6. Troubleshooting @@ -16,27 +24,48 @@ Content ----------------------------------------------------------------------------- 1. Introduction - The Smartio family Linux driver, Ver. 1.1, supports following multiport + The Smartio/Industio/UPCI family Linux driver supports following multiport boards. - -C104P/H/HS, C104H/PCI, C104HS/PCI, CI-104J 4 port multiport board. - -C168P/H/HS, C168H/PCI 8 port multiport board. - - This driver has been modified a little and cleaned up from the Moxa - contributed driver code and merged into Linux 2.2.14pre. In particular - official major/minor numbers have been assigned which are different to - those the original Moxa supplied driver used. + - 2 ports multiport board + CP-102U, CP-102UL, CP-102UF + CP-132U-I, CP-132UL, + CP-132, CP-132I, CP132S, CP-132IS, + CI-132, CI-132I, CI-132IS, + (C102H, C102HI, C102HIS, C102P, CP-102, CP-102S) + + - 4 ports multiport board + CP-104EL, + CP-104UL, CP-104JU, + CP-134U, CP-134U-I, + C104H/PCI, C104HS/PCI, + CP-114, CP-114I, CP-114S, CP-114IS, CP-114UL, + C104H, C104HS, + CI-104J, CI-104JS, + CI-134, CI-134I, CI-134IS, + (C114HI, CT-114I, C104P) + POS-104UL, + CB-114, + CB-134I + + - 8 ports multiport board + CP-118EL, CP-168EL, + CP-118U, CP-168U, + C168H/PCI, + C168H, C168HS, + (C168P), + CB-108 This driver and installation procedure have been developed upon Linux Kernel - 2.2.5 and backward compatible to 2.0.3x. This driver supports Intel x86 and - Alpha hardware platform. In order to maintain compatibility, this version - has also been properly tested with RedHat, OpenLinux, TurboLinux and - S.u.S.E Linux. However, if compatibility problem occurs, please contact - Moxa at support@moxa.com.tw. + 2.4.x and 2.6.x. This driver supports Intel x86 hardware platform. In order + to maintain compatibility, this version has also been properly tested with + RedHat, Mandrake, Fedora and S.u.S.E Linux. However, if compatibility problem + occurs, please contact Moxa at support@moxa.com.tw. In addition to device driver, useful utilities are also provided in this version. They are - - msdiag Diagnostic program for detecting installed Moxa Smartio boards. + - msdiag Diagnostic program for displaying installed Moxa + Smartio/Industio boards. - msmon Monitor program to observe data count and line status signals. - msterm A simple terminal program which is useful in testing serial ports. @@ -47,8 +76,7 @@ Content GNU General Public License in this version. Please refer to GNU General Public License announcement in each source code file for more detail. - In Moxa's ftp sites, you may always find latest driver at - ftp://ftp.moxa.com or ftp://ftp.moxa.com.tw. + In Moxa's Web sites, you may always find latest driver at http://web.moxa.com. This version of driver can be installed as Loadable Module (Module driver) or built-in into kernel (Static driver). You may refer to following @@ -61,18 +89,27 @@ Content ----------------------------------------------------------------------------- 2. System Requirement - - Hardware platform: Intel x86 or Alpha machine - - Kernel version: 2.0.3x or 2.2.x + - Hardware platform: Intel x86 machine + - Kernel version: 2.4.x or 2.6.x - gcc version 2.72 or later - Maximum 4 boards can be installed in combination ----------------------------------------------------------------------------- 3. Installation + 3.1 Hardware installation + 3.2 Driver files + 3.3 Device naming convention + 3.4 Module driver configuration + 3.5 Static driver configuration for Linux kernel 2.4.x, 2.6.x. + 3.6 Custom configuration + 3.7 Verify driver installation + + 3.1 Hardware installation - There are two types of buses, ISA and PCI, for Smartio family multiport - board. + There are two types of buses, ISA and PCI, for Smartio/Industio + family multiport board. ISA board --------- @@ -81,47 +118,57 @@ Content installation procedure in User's Manual before proceed any further. Please make sure the JP1 is open after the ISA board is set properly. - PCI board - --------- + PCI/UPCI board + -------------- You may need to adjust IRQ usage in BIOS to avoid from IRQ conflict with other ISA devices. Please refer to hardware installation procedure in User's Manual in advance. - IRQ Sharing + PCI IRQ Sharing ----------- Each port within the same multiport board shares the same IRQ. Up to - 4 Moxa Smartio Family multiport boards can be installed together on - one system and they can share the same IRQ. + 4 Moxa Smartio/Industio PCI Family multiport boards can be installed + together on one system and they can share the same IRQ. + - 3.2 Driver files and device naming convention + 3.2 Driver files The driver file may be obtained from ftp, CD-ROM or floppy disk. The first step, anyway, is to copy driver file "mxser.tgz" into specified directory. e.g. /moxa. The execute commands as below. + # cd / + # mkdir moxa # cd /moxa - # tar xvf /dev/fd0 + # tar xvf /dev/fd0 + or + + # cd / + # mkdir moxa # cd /moxa # cp /mnt/cdrom//mxser.tgz . # tar xvfz mxser.tgz + + 3.3 Device naming convention + You may find all the driver and utilities files in /moxa/mxser. Following installation procedure depends on the model you'd like to - run the driver. If you prefer module driver, please refer to 3.3. - If static driver is required, please refer to 3.4. + run the driver. If you prefer module driver, please refer to 3.4. + If static driver is required, please refer to 3.5. Dialin and callout port ----------------------- - This driver remains traditional serial device properties. There're + This driver remains traditional serial device properties. There are two special file name for each serial port. One is dial-in port which is named "ttyMxx". For callout port, the naming convention is "cumxx". Device naming when more than 2 boards installed ----------------------------------------------- - Naming convention for each Smartio multiport board is pre-defined - as below. + Naming convention for each Smartio/Industio multiport board is + pre-defined as below. Board Num. Dial-in Port Callout port 1st board ttyM0 - ttyM7 cum0 - cum7 @@ -129,6 +176,12 @@ Content 3rd board ttyM16 - ttyM23 cum16 - cum23 4th board ttyM24 - ttym31 cum24 - cum31 + + !!!!!!!!!!!!!!!!!!!! NOTE !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! + Under Kernel 2.6 the cum Device is Obsolete. So use ttyM* + device instead. + !!!!!!!!!!!!!!!!!!!! NOTE !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! + Board sequence -------------- This driver will activate ISA boards according to the parameter set @@ -138,69 +191,131 @@ Content For PCI boards, their sequence will be after ISA boards and C168H/PCI has higher priority than C104H/PCI boards. - 3.3 Module driver configuration + 3.4 Module driver configuration Module driver is easiest way to install. If you prefer static driver installation, please skip this paragraph. - 1. Find "Makefile" in /moxa/mxser, then run - # make install + + ------------- Prepare to use the MOXA driver-------------------- + 3.4.1 Create tty device with correct major number + Before using MOXA driver, your system must have the tty devices + which are created with driver's major number. We offer one shell + script "msmknod" to simplify the procedure. + This step is only needed to be executed once. But you still + need to do this procedure when: + a. You change the driver's major number. Please refer the "3.7" + section. + b. Your total installed MOXA boards number is changed. Maybe you + add/delete one MOXA board. + c. You want to change the tty name. This needs to modify the + shell script "msmknod" + + The procedure is: + # cd /moxa/mxser/driver + # ./msmknod + + This shell script will require the major number for dial-in + device and callout device to create tty device. You also need + to specify the total installed MOXA board number. Default major + numbers for dial-in device and callout device are 30, 35. If + you need to change to other number, please refer section "3.7" + for more detailed procedure. + Msmknod will delete any special files occupying the same device + naming. + + 3.4.2 Build the MOXA driver and utilities + Before using the MOXA driver and utilities, you need compile the + all the source code. This step is only need to be executed once. + But you still re-compile the source code if you modify the source + code. For example, if you change the driver's major number (see + "3.7" section), then you need to do this step again. + + Find "Makefile" in /moxa/mxser, then run + + # make clean; make install + + !!!!!!!!!! NOTE !!!!!!!!!!!!!!!!! + For Red Hat 9, Red Hat Enterprise Linux AS3/ES3/WS3 & Fedora Core1: + # make clean; make installsp1 + + For Red Hat Enterprise Linux AS4/ES4/WS4: + # make clean; make installsp2 + !!!!!!!!!! NOTE !!!!!!!!!!!!!!!!! The driver files "mxser.o" and utilities will be properly compiled - and copied to system directories respectively.Then run + and copied to system directories respectively. - # insmod mxser + ------------- Load MOXA driver-------------------- + 3.4.3 Load the MOXA driver - to activate the modular driver. You may run "lsmod" to check - if "mxser.o" is activated. + # modprobe mxser - 2. Create special files by executing "msmknod". - # cd /moxa/mxser/driver - # ./msmknod + will activate the module driver. You may run "lsmod" to check + if "mxser" is activated. If the MOXA board is ISA board, the + is needed. Please refer to section "3.4.5" for more + information. + + + ------------- Load MOXA driver on boot -------------------- + 3.4.4 For the above description, you may manually execute + "modprobe mxser" to activate this driver and run + "rmmod mxser" to remove it. + However, it's better to have a boot time configuration to + eliminate manual operation. Boot time configuration can be + achieved by rc file. We offer one "rc.mxser" file to simplify + the procedure under "moxa/mxser/driver". - Default major numbers for dial-in device and callout device are - 174, 175. Msmknod will delete any special files occupying the same - device naming. + But if you use ISA board, please modify the "modprobe ..." command + to add the argument (see "3.4.5" section). After modifying the + rc.mxser, please try to execute "/moxa/mxser/driver/rc.mxser" + manually to make sure the modification is ok. If any error + encountered, please try to modify again. If the modification is + completed, follow the below step. - 3. Up to now, you may manually execute "insmod mxser" to activate - this driver and run "rmmod mxser" to remove it. However, it's - better to have a boot time configuration to eliminate manual - operation. - Boot time configuration can be achieved by rc file. Run following - command for setting rc files. + Run following command for setting rc files. # cd /moxa/mxser/driver # cp ./rc.mxser /etc/rc.d # cd /etc/rc.d - You may have to modify part of the content in rc.mxser to specify - parameters for ISA board. Please refer to rc.mxser for more detail. - Find "rc.serial". If "rc.serial" doesn't exist, create it by vi. - Add "rc.mxser" in last line. Next, open rc.local by vi - and append following content. + Check "rc.serial" is existed or not. If "rc.serial" doesn't exist, + create it by vi, run "chmod 755 rc.serial" to change the permission. + Add "/etc/rc.d/rc.mxser" in last line, - if [ -f /etc/rc.d/rc.serial ]; then - sh /etc/rc.d/rc.serial - fi + Reboot and check if moxa.o activated by "lsmod" command. - 4. Reboot and check if mxser.o activated by "lsmod" command. - 5. If you'd like to drive Smartio ISA boards in the system, you'll - have to add parameter to specify CAP address of given board while - activating "mxser.o". The format for parameters are as follows. + 3.4.5. If you'd like to drive Smartio/Industio ISA boards in the system, + you'll have to add parameter to specify CAP address of given + board while activating "mxser.o". The format for parameters are + as follows. - insmod mxser ioaddr=0x???,0x???,0x???,0x??? + modprobe mxser ioaddr=0x???,0x???,0x???,0x??? | | | | | | | +- 4th ISA board | | +------ 3rd ISA board | +------------ 2nd ISA board +------------------- 1st ISA board - 3.4 Static driver configuration + 3.5 Static driver configuration for Linux kernel 2.4.x and 2.6.x + + Note: To use static driver, you must install the linux kernel + source package. + + 3.5.1 Backup the built-in driver in the kernel. + # cd /usr/src/linux/drivers/char + # mv mxser.c mxser.c.old + + For Red Hat 7.x user, you need to create link: + # cd /usr/src + # ln -s linux-2.4 linux - 1. Create link + 3.5.2 Create link # cd /usr/src/linux/drivers/char # ln -s /moxa/mxser/driver/mxser.c mxser.c - 2. Add CAP address list for ISA boards + 3.5.3 Add CAP address list for ISA boards. For PCI boards user, + please skip this step. + In module mode, the CAP address for ISA board is given by parameter. In static driver configuration, you'll have to assign it within driver's source code. If you will not @@ -222,73 +337,55 @@ Content static int mxserBoardCAP[] = {0x280, 0x180, 0x00, 0x00}; - 3. Modify tty_io.c - # cd /usr/src/linux/drivers/char/ - # vi tty_io.c - Find pty_init(), insert "mxser_init()" as + 3.5.4 Setup kernel configuration - pty_init(); - mxser_init(); + Configure the kernel: - 4. Modify tty.h - # cd /usr/src/linux/include/linux - # vi tty.h - Find extern int tty_init(void), insert "mxser_init()" as + # cd /usr/src/linux + # make menuconfig - extern int tty_init(void); - extern int mxser_init(void); - - 5. Modify Makefile - # cd /usr/src/linux/drivers/char - # vi Makefile - Find L_OBJS := tty_io.o ...... random.o, add - "mxser.o" at last of this line as - L_OBJS := tty_io.o ....... mxser.o + You will go into a menu-driven system. Please select [Character + devices][Non-standard serial port support], enable the [Moxa + SmartIO support] driver with "[*]" for built-in (not "[M]"), then + select [Exit] to exit this program. - 6. Rebuild kernel - The following are for Linux kernel rebuilding,for your reference only. + 3.5.5 Rebuild kernel + The following are for Linux kernel rebuilding, for your + reference only. For appropriate details, please refer to the Linux document. - If 'lilo' utility is installed, please use 'make zlilo' to rebuild - kernel. If 'lilo' is not installed, please follow the following steps. - a. cd /usr/src/linux - b. make clean /* take a few minutes */ - c. make bzImage /* take probably 10-20 minutes */ - d. Backup original boot kernel. /* optional step */ - e. cp /usr/src/linux/arch/i386/boot/bzImage /boot/vmlinuz + b. make clean /* take a few minutes */ + c. make dep /* take a few minutes */ + d. make bzImage /* take probably 10-20 minutes */ + e. make install /* copy boot image to correct position */ f. Please make sure the boot kernel (vmlinuz) is in the - correct position. If you use 'lilo' utility, you should - check /etc/lilo.conf 'image' item specified the path - which is the 'vmlinuz' path, or you will load wrong - (or old) boot kernel image (vmlinuz). - g. chmod 400 /vmlinuz - h. lilo - i. rdev -R /vmlinuz 1 - j. sync - - Note that if the result of "make zImage" is ERROR, then you have to - go back to Linux configuration Setup. Type "make config" in directory - /usr/src/linux or "setup". - - Since system include file, /usr/src/linux/include/linux/interrupt.h, - is modified each time the MOXA driver is installed, kernel rebuilding - is inevitable. And it takes about 10 to 20 minutes depends on the - machine. - - 7. Make utility - # cd /moxa/mxser/utility - # make install - - 8. Make special file + correct position. + g. If you use 'lilo' utility, you should check /etc/lilo.conf + 'image' item specified the path which is the 'vmlinuz' path, + or you will load wrong (or old) boot kernel image (vmlinuz). + After checking /etc/lilo.conf, please run "lilo". + + Note that if the result of "make bzImage" is ERROR, then you have to + go back to Linux configuration Setup. Type "make menuconfig" in + directory /usr/src/linux. + + + 3.5.6 Make tty device and special file # cd /moxa/mxser/driver # ./msmknod - 9. Reboot + 3.5.7 Make utility + # cd /moxa/mxser/utility + # make clean; make install + + 3.5.8 Reboot - 3.5 Custom configuration + + + 3.6 Custom configuration Although this driver already provides you default configuration, you - still can change the device name and major number.The instruction to + still can change the device name and major number. The instruction to change these parameters are shown as below. Change Device name @@ -306,33 +403,37 @@ Content 2 free major numbers for this driver. There are 3 steps to change major numbers. - 1. Find free major numbers + 3.6.1 Find free major numbers In /proc/devices, you may find all the major numbers occupied in the system. Please select 2 major numbers that are available. e.g. 40, 45. - 2. Create special files + 3.6.2 Create special files Run /moxa/mxser/driver/msmknod to create special files with specified major numbers. - 3. Modify driver with new major number + 3.6.3 Modify driver with new major number Run vi to open /moxa/mxser/driver/mxser.c. Locate the line contains "MXSERMAJOR". Change the content as below. #define MXSERMAJOR 40 #define MXSERCUMAJOR 45 - 4. Run # make install in /moxa/mxser/driver. + 3.6.4 Run "make clean; make install" in /moxa/mxser/driver. - 3.6 Verify driver installation + 3.7 Verify driver installation You may refer to /var/log/messages to check the latest status log reported by this driver whenever it's activated. + ----------------------------------------------------------------------------- 4. Utilities There are 3 utilities contained in this driver. They are msdiag, msmon and msterm. These 3 utilities are released in form of source code. They should be compiled into executable file and copied into /usr/bin. + Before using these utilities, please load driver (refer 3.4 & 3.5) and + make sure you had run the "msmknod" utility. + msdiag - Diagnostic -------------------- - This utility provides the function to detect what Moxa Smartio multiport - board exists in the system. + This utility provides the function to display what Moxa Smartio/Industio + board found by driver in the system. msmon - Port Monitoring ----------------------- @@ -353,12 +454,13 @@ Content application, for example, sending AT command to a modem connected to the port or used as a terminal for login purpose. Note that this is only a dumb terminal emulation without handling full screen operation. + ----------------------------------------------------------------------------- 5. Setserial Supported Setserial parameters are listed as below. - uart set UART type(16450-->disable FIFO, 16550A-->enable FIFO) + uart set UART type(16450-->disable FIFO, 16550A-->enable FIFO) close_delay set the amount of time(in 1/100 of a second) that DTR should be kept low while being closed. closing_wait set the amount of time(in 1/100 of a second) that the @@ -366,7 +468,13 @@ Content being closed, before the receiver is disable. spd_hi Use 57.6kb when the application requests 38.4kb. spd_vhi Use 115.2kb when the application requests 38.4kb. + spd_shi Use 230.4kb when the application requests 38.4kb. + spd_warp Use 460.8kb when the application requests 38.4kb. spd_normal Use 38.4kb when the application requests 38.4kb. + spd_cust Use the custom divisor to set the speed when the + application requests 38.4kb. + divisor This option set the custom divison. + baud_base This option set the base baud rate. ----------------------------------------------------------------------------- 6. Troubleshooting @@ -375,8 +483,9 @@ Content possible. If all the possible solutions fail, please contact our technical support team to get more help. - Error msg: More than 4 Moxa Smartio family boards found. Fifth board and - after are ignored. + + Error msg: More than 4 Moxa Smartio/Industio family boards found. Fifth board + and after are ignored. Solution: To avoid this problem, please unplug fifth and after board, because Moxa driver supports up to 4 boards. @@ -384,7 +493,7 @@ Content Error msg: Request_irq fail, IRQ(?) may be conflict with another device. Solution: Other PCI or ISA devices occupy the assigned IRQ. If you are not sure - which device causes the situation,please check /proc/interrupts to find + which device causes the situation, please check /proc/interrupts to find free IRQ and simply change another free IRQ for Moxa board. Error msg: Board #: C1xx Series(CAP=xxx) interrupt number invalid. @@ -397,15 +506,18 @@ Content Moxa ISA board needs an interrupt vector.Please refer to user's manual "Hardware Installation" chapter to set interrupt vector. - Error msg: Couldn't install MOXA Smartio family driver! + Error msg: Couldn't install MOXA Smartio/Industio family driver! Solution: Load Moxa driver fail, the major number may conflict with other devices. - Please refer to previous section 3.5 to change a free major number for + Please refer to previous section 3.7 to change a free major number for Moxa driver. - Error msg: Couldn't install MOXA Smartio family callout driver! + Error msg: Couldn't install MOXA Smartio/Industio family callout driver! Solution: Load Moxa callout driver fail, the callout device major number may - conflict with other devices. Please refer to previous section 3.5 to + conflict with other devices. Please refer to previous section 3.7 to change a free callout device major number for Moxa driver. + + ----------------------------------------------------------------------------- + diff --git a/Documentation/networking/bonding.txt b/Documentation/networking/bonding.txt index a0cda062bc33b6e1de3dd2bb60d5ff62bdf97cd4..688dfe1e6b70f75a36d84f30dda2234c53664be0 100644 --- a/Documentation/networking/bonding.txt +++ b/Documentation/networking/bonding.txt @@ -289,35 +289,73 @@ downdelay fail_over_mac Specifies whether active-backup mode should set all slaves to - the same MAC address (the traditional behavior), or, when - enabled, change the bond's MAC address when changing the - active interface (i.e., fail over the MAC address itself). - - Fail over MAC is useful for devices that cannot ever alter - their MAC address, or for devices that refuse incoming - broadcasts with their own source MAC (which interferes with - the ARP monitor). - - The down side of fail over MAC is that every device on the - network must be updated via gratuitous ARP, vs. just updating - a switch or set of switches (which often takes place for any - traffic, not just ARP traffic, if the switch snoops incoming - traffic to update its tables) for the traditional method. If - the gratuitous ARP is lost, communication may be disrupted. - - When fail over MAC is used in conjuction with the mii monitor, - devices which assert link up prior to being able to actually - transmit and receive are particularly susecptible to loss of - the gratuitous ARP, and an appropriate updelay setting may be - required. - - A value of 0 disables fail over MAC, and is the default. A - value of 1 enables fail over MAC. This option is enabled - automatically if the first slave added cannot change its MAC - address. This option may be modified via sysfs only when no - slaves are present in the bond. - - This option was added in bonding version 3.2.0. + the same MAC address at enslavement (the traditional + behavior), or, when enabled, perform special handling of the + bond's MAC address in accordance with the selected policy. + + Possible values are: + + none or 0 + + This setting disables fail_over_mac, and causes + bonding to set all slaves of an active-backup bond to + the same MAC address at enslavement time. This is the + default. + + active or 1 + + The "active" fail_over_mac policy indicates that the + MAC address of the bond should always be the MAC + address of the currently active slave. The MAC + address of the slaves is not changed; instead, the MAC + address of the bond changes during a failover. + + This policy is useful for devices that cannot ever + alter their MAC address, or for devices that refuse + incoming broadcasts with their own source MAC (which + interferes with the ARP monitor). + + The down side of this policy is that every device on + the network must be updated via gratuitous ARP, + vs. just updating a switch or set of switches (which + often takes place for any traffic, not just ARP + traffic, if the switch snoops incoming traffic to + update its tables) for the traditional method. If the + gratuitous ARP is lost, communication may be + disrupted. + + When this policy is used in conjuction with the mii + monitor, devices which assert link up prior to being + able to actually transmit and receive are particularly + susecptible to loss of the gratuitous ARP, and an + appropriate updelay setting may be required. + + follow or 2 + + The "follow" fail_over_mac policy causes the MAC + address of the bond to be selected normally (normally + the MAC address of the first slave added to the bond). + However, the second and subsequent slaves are not set + to this MAC address while they are in a backup role; a + slave is programmed with the bond's MAC address at + failover time (and the formerly active slave receives + the newly active slave's MAC address). + + This policy is useful for multiport devices that + either become confused or incur a performance penalty + when multiple ports are programmed with the same MAC + address. + + + The default policy is none, unless the first slave cannot + change its MAC address, in which case the active policy is + selected by default. + + This option may be modified via sysfs only when no slaves are + present in the bond. + + This option was added in bonding version 3.2.0. The "follow" + policy was added in bonding version 3.3.0. lacp_rate @@ -338,7 +376,8 @@ max_bonds Specifies the number of bonding devices to create for this instance of the bonding driver. E.g., if max_bonds is 3, and the bonding driver is not already loaded, then bond0, bond1 - and bond2 will be created. The default value is 1. + and bond2 will be created. The default value is 1. Specifying + a value of 0 will load bonding, but will not create any devices. miimon @@ -501,6 +540,17 @@ mode swapped with the new curr_active_slave that was chosen. +num_grat_arp + + Specifies the number of gratuitous ARPs to be issued after a + failover event. One gratuitous ARP is issued immediately after + the failover, subsequent ARPs are sent at a rate of one per link + monitor interval (arp_interval or miimon, whichever is active). + + The valid range is 0 - 255; the default value is 1. This option + affects only the active-backup mode. This option was added for + bonding version 3.3.0. + primary A string (eth0, eth2, etc) specifying which slave is the @@ -581,7 +631,7 @@ xmit_hash_policy in environments where a layer3 gateway device is required to reach most destinations. - This algorithm is 802.3ad complient. + This algorithm is 802.3ad compliant. layer3+4 diff --git a/Documentation/networking/can.txt b/Documentation/networking/can.txt index 641d2afacffa33094a5ee7a52e6646ec7c089220..297ba7b1ccaf953ff85e486baa0a7547450db31c 100644 --- a/Documentation/networking/can.txt +++ b/Documentation/networking/can.txt @@ -186,7 +186,7 @@ solution for a couple of reasons: The Linux network devices (by default) just can handle the transmission and reception of media dependent frames. Due to the - arbritration on the CAN bus the transmission of a low prio CAN-ID + arbitration on the CAN bus the transmission of a low prio CAN-ID may be delayed by the reception of a high prio CAN frame. To reflect the correct* traffic on the node the loopback of the sent data has to be performed right after a successful transmission. If @@ -481,7 +481,7 @@ solution for a couple of reasons: - stats_timer: To calculate the Socket CAN core statistics (e.g. current/maximum frames per second) this 1 second timer is invoked at can.ko module start time by default. This timer can be - disabled by using stattimer=0 on the module comandline. + disabled by using stattimer=0 on the module commandline. - debug: (removed since SocketCAN SVN r546) diff --git a/Documentation/networking/dm9000.txt b/Documentation/networking/dm9000.txt new file mode 100644 index 0000000000000000000000000000000000000000..65df3dea55613bd581dd787305054b7062657507 --- /dev/null +++ b/Documentation/networking/dm9000.txt @@ -0,0 +1,167 @@ +DM9000 Network driver +===================== + +Copyright 2008 Simtec Electronics, + Ben Dooks + + +Introduction +------------ + +This file describes how to use the DM9000 platform-device based network driver +that is contained in the files drivers/net/dm9000.c and drivers/net/dm9000.h. + +The driver supports three DM9000 variants, the DM9000E which is the first chip +supported as well as the newer DM9000A and DM9000B devices. It is currently +maintained and tested by Ben Dooks, who should be CC: to any patches for this +driver. + + +Defining the platform device +---------------------------- + +The minimum set of resources attached to the platform device are as follows: + + 1) The physical address of the address register + 2) The physical address of the data register + 3) The IRQ line the device's interrupt pin is connected to. + +These resources should be specified in that order, as the ordering of the +two address regions is important (the driver expects these to be address +and then data). + +An example from arch/arm/mach-s3c2410/mach-bast.c is: + +static struct resource bast_dm9k_resource[] = { + [0] = { + .start = S3C2410_CS5 + BAST_PA_DM9000, + .end = S3C2410_CS5 + BAST_PA_DM9000 + 3, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = S3C2410_CS5 + BAST_PA_DM9000 + 0x40, + .end = S3C2410_CS5 + BAST_PA_DM9000 + 0x40 + 0x3f, + .flags = IORESOURCE_MEM, + }, + [2] = { + .start = IRQ_DM9000, + .end = IRQ_DM9000, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + } +}; + +static struct platform_device bast_device_dm9k = { + .name = "dm9000", + .id = 0, + .num_resources = ARRAY_SIZE(bast_dm9k_resource), + .resource = bast_dm9k_resource, +}; + +Note the setting of the IRQ trigger flag in bast_dm9k_resource[2].flags, +as this will generate a warning if it is not present. The trigger from +the flags field will be passed to request_irq() when registering the IRQ +handler to ensure that the IRQ is setup correctly. + +This shows a typical platform device, without the optional configuration +platform data supplied. The next example uses the same resources, but adds +the optional platform data to pass extra configuration data: + +static struct dm9000_plat_data bast_dm9k_platdata = { + .flags = DM9000_PLATF_16BITONLY, +}; + +static struct platform_device bast_device_dm9k = { + .name = "dm9000", + .id = 0, + .num_resources = ARRAY_SIZE(bast_dm9k_resource), + .resource = bast_dm9k_resource, + .dev = { + .platform_data = &bast_dm9k_platdata, + } +}; + +The platform data is defined in include/linux/dm9000.h and described below. + + +Platform data +------------- + +Extra platform data for the DM9000 can describe the IO bus width to the +device, whether or not an external PHY is attached to the device and +the availability of an external configuration EEPROM. + +The flags for the platform data .flags field are as follows: + +DM9000_PLATF_8BITONLY + + The IO should be done with 8bit operations. + +DM9000_PLATF_16BITONLY + + The IO should be done with 16bit operations. + +DM9000_PLATF_32BITONLY + + The IO should be done with 32bit operations. + +DM9000_PLATF_EXT_PHY + + The chip is connected to an external PHY. + +DM9000_PLATF_NO_EEPROM + + This can be used to signify that the board does not have an + EEPROM, or that the EEPROM should be hidden from the user. + +DM9000_PLATF_SIMPLE_PHY + + Switch to using the simpler PHY polling method which does not + try and read the MII PHY state regularly. This is only available + when using the internal PHY. See the section on link state polling + for more information. + + The config symbol DM9000_FORCE_SIMPLE_PHY_POLL, Kconfig entry + "Force simple NSR based PHY polling" allows this flag to be + forced on at build time. + + +PHY Link state polling +---------------------- + +The driver keeps track of the link state and informs the network core +about link (carrier) availablilty. This is managed by several methods +depending on the version of the chip and on which PHY is being used. + +For the internal PHY, the original (and currently default) method is +to read the MII state, either when the status changes if we have the +necessary interrupt support in the chip or every two seconds via a +periodic timer. + +To reduce the overhead for the internal PHY, there is now the option +of using the DM9000_FORCE_SIMPLE_PHY_POLL config, or DM9000_PLATF_SIMPLE_PHY +platform data option to read the summary information without the +expensive MII accesses. This method is faster, but does not print +as much information. + +When using an external PHY, the driver currently has to poll the MII +link status as there is no method for getting an interrupt on link change. + + +DM9000A / DM9000B +----------------- + +These chips are functionally similar to the DM9000E and are supported easily +by the same driver. The features are: + + 1) Interrupt on internal PHY state change. This means that the periodic + polling of the PHY status may be disabled on these devices when using + the internal PHY. + + 2) TCP/UDP checksum offloading, which the driver does not currently support. + + +ethtool +------- + +The driver supports the ethtool interface for access to the driver +state information, the PHY state and the EEPROM. diff --git a/Documentation/networking/e1000.txt b/Documentation/networking/e1000.txt index 61b171cf5313c9b94c3e4fe185a9ff9edf9b5cbc..2df71861e578b6ebcb2b94371d4a32fbdf7fca61 100644 --- a/Documentation/networking/e1000.txt +++ b/Documentation/networking/e1000.txt @@ -513,21 +513,11 @@ Additional Configurations Intel(R) PRO/1000 PT Dual Port Server Connection Intel(R) PRO/1000 PT Dual Port Server Adapter Intel(R) PRO/1000 PF Dual Port Server Adapter - Intel(R) PRO/1000 PT Quad Port Server Adapter + Intel(R) PRO/1000 PT Quad Port Server Adapter NAPI ---- - NAPI (Rx polling mode) is supported in the e1000 driver. NAPI is enabled - or disabled based on the configuration of the kernel. To override - the default, use the following compile-time flags. - - To enable NAPI, compile the driver module, passing in a configuration option: - - make CFLAGS_EXTRA=-DE1000_NAPI install - - To disable NAPI, compile the driver module, passing in a configuration option: - - make CFLAGS_EXTRA=-DE1000_NO_NAPI install + NAPI (Rx polling mode) is enabled in the e1000 driver. See www.cyberus.ca/~hadi/usenix-paper.tgz for more information on NAPI. diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt index 946b66e1b65214f4becc5d2563f73180fe331837..d84932650fd3e926cc11d5fa0bcaee6cc8a8cd33 100644 --- a/Documentation/networking/ip-sysctl.txt +++ b/Documentation/networking/ip-sysctl.txt @@ -551,8 +551,9 @@ icmp_echo_ignore_broadcasts - BOOLEAN icmp_ratelimit - INTEGER Limit the maximal rates for sending ICMP packets whose type matches icmp_ratemask (see below) to specific targets. - 0 to disable any limiting, otherwise the maximal rate in jiffies(1) - Default: 100 + 0 to disable any limiting, + otherwise the minimal space between responses in milliseconds. + Default: 1000 icmp_ratemask - INTEGER Mask made of ICMP types for which rates are being limited. @@ -1023,11 +1024,23 @@ max_addresses - INTEGER autoconfigured addresses. Default: 16 +disable_ipv6 - BOOLEAN + Disable IPv6 operation. + Default: FALSE (enable IPv6 operation) + +accept_dad - INTEGER + Whether to accept DAD (Duplicate Address Detection). + 0: Disable DAD + 1: Enable DAD (default) + 2: Enable DAD, and disable IPv6 operation if MAC-based duplicate + link-local address has been found. + icmp/*: ratelimit - INTEGER Limit the maximal rates for sending ICMPv6 packets. - 0 to disable any limiting, otherwise the maximal rate in jiffies(1) - Default: 100 + 0 to disable any limiting, + otherwise the minimal space between responses in milliseconds. + Default: 1000 IPv6 Update by: diff --git a/Documentation/networking/ixgb.txt b/Documentation/networking/ixgb.txt index 7c98277777ebcc14ee7c30991873cc6c92296d28..a0d0ffb5e584c1ae1b24a49552bfaef4c3b4684a 100644 --- a/Documentation/networking/ixgb.txt +++ b/Documentation/networking/ixgb.txt @@ -1,7 +1,7 @@ -Linux* Base Driver for the Intel(R) PRO/10GbE Family of Adapters -================================================================ +Linux Base Driver for 10 Gigabit Intel(R) Network Connection +============================================================= -November 17, 2004 +October 9, 2007 Contents @@ -9,94 +9,151 @@ Contents - In This Release - Identifying Your Adapter +- Building and Installation - Command Line Parameters - Improving Performance +- Additional Configurations +- Known Issues/Troubleshooting - Support + In This Release =============== -This file describes the Linux* Base Driver for the Intel(R) PRO/10GbE Family -of Adapters, version 1.0.x. +This file describes the ixgb Linux Base Driver for the 10 Gigabit Intel(R) +Network Connection. This driver includes support for Itanium(R)2-based +systems. + +For questions related to hardware requirements, refer to the documentation +supplied with your 10 Gigabit adapter. All hardware requirements listed apply +to use with Linux. + +The following features are available in this kernel: + - Native VLANs + - Channel Bonding (teaming) + - SNMP + +Channel Bonding documentation can be found in the Linux kernel source: +/Documentation/networking/bonding.txt + +The driver information previously displayed in the /proc filesystem is not +supported in this release. Alternatively, you can use ethtool (version 1.6 +or later), lspci, and ifconfig to obtain the same information. + +Instructions on updating ethtool can be found in the section "Additional +Configurations" later in this document. -For questions related to hardware requirements, refer to the documentation -supplied with your Intel PRO/10GbE adapter. All hardware requirements listed -apply to use with Linux. Identifying Your Adapter ======================== -To verify your Intel adapter is supported, find the board ID number on the -adapter. Look for a label that has a barcode and a number in the format -A12345-001. +The following Intel network adapters are compatible with the drivers in this +release: + +Controller Adapter Name Physical Layer +---------- ------------ -------------- +82597EX Intel(R) PRO/10GbE LR/SR/CX4 10G Base-LR (1310 nm optical fiber) + Server Adapters 10G Base-SR (850 nm optical fiber) + 10G Base-CX4(twin-axial copper cabling) + +For more information on how to identify your adapter, go to the Adapter & +Driver ID Guide at: + + http://support.intel.com/support/network/sb/CS-012904.htm + + +Building and Installation +========================= + +select m for "Intel(R) PRO/10GbE support" located at: + Location: + -> Device Drivers + -> Network device support (NETDEVICES [=y]) + -> Ethernet (10000 Mbit) (NETDEV_10000 [=y]) +1. make modules && make modules_install + +2. Load the module: + +    modprobe ixgb = + + The insmod command can be used if the full + path to the driver module is specified. For example: + + insmod /lib/modules//kernel/drivers/net/ixgb/ixgb.ko + + With 2.6 based kernels also make sure that older ixgb drivers are + removed from the kernel, before loading the new module: -Use the above information and the Adapter & Driver ID Guide at: + rmmod ixgb; modprobe ixgb - http://support.intel.com/support/network/adapter/pro100/21397.htm +3. Assign an IP address to the interface by entering the following, where + x is the interface number: -For the latest Intel network drivers for Linux, go to: + ifconfig ethx + +4. Verify that the interface works. Enter the following, where + is the IP address for another machine on the same subnet as the interface + that is being tested: + + ping - http://downloadfinder.intel.com/scripts-df/support_intel.asp Command Line Parameters ======================= -If the driver is built as a module, the following optional parameters are -used by entering them on the command line with the modprobe or insmod command -using this syntax: +If the driver is built as a module, the following optional parameters are +used by entering them on the command line with the modprobe command using +this syntax: modprobe ixgb [