From a7aea373b4ca428f1be2c1fedd2f26c8e3f2864d Mon Sep 17 00:00:00 2001 From: "Ira W. Snyder" Date: Thu, 23 Apr 2009 16:17:54 -0700 Subject: [PATCH 0001/1342] fsldma: use PCI Read Multiple command By default, the Freescale 83xx DMA controller uses the PCI Read Line command when reading data over the PCI bus. Setting the controller to use the PCI Read Multiple command instead allows the controller to read much larger bursts of data, which provides a drastic speed increase. The slowdown due to using PCI Read Line was only observed when a PCI-to-PCI bridge was between the devices trying to communicate. A simple test driver showed an increase from 4MB/sec to 116MB/sec when performing DMA over the PCI bus. Using DMA to transfer between blocks of local SDRAM showed no change in performance with this patch. The dmatest driver was also used to verify the correctness of the transfers, and showed no errors. Signed-off-by: Ira W. Snyder Acked-by: Timur Tabi Acked-by: Kumar Gala Signed-off-by: Dan Williams --- drivers/dma/fsldma.c | 10 ++++++++-- drivers/dma/fsldma.h | 1 + 2 files changed, 9 insertions(+), 2 deletions(-) diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c index f18d1bde043..a1cb25e277b 100644 --- a/drivers/dma/fsldma.c +++ b/drivers/dma/fsldma.c @@ -12,6 +12,11 @@ * also fit for MPC8560, MPC8555, MPC8548, MPC8641, and etc. * The support for MPC8349 DMA contorller is also added. * + * This driver instructs the DMA controller to issue the PCI Read Multiple + * command for PCI read operations, instead of using the default PCI Read Line + * command. Please be aware that this setting may result in read pre-fetching + * on some platforms. + * * This is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or @@ -49,9 +54,10 @@ static void dma_init(struct fsl_dma_chan *fsl_chan) case FSL_DMA_IP_83XX: /* Set the channel to below modes: * EOTIE - End-of-transfer interrupt enable + * PRC_RM - PCI read multiple */ - DMA_OUT(fsl_chan, &fsl_chan->reg_base->mr, FSL_DMA_MR_EOTIE, - 32); + DMA_OUT(fsl_chan, &fsl_chan->reg_base->mr, FSL_DMA_MR_EOTIE + | FSL_DMA_MR_PRC_RM, 32); break; } diff --git a/drivers/dma/fsldma.h b/drivers/dma/fsldma.h index 4f21a512d84..dc7f2686579 100644 --- a/drivers/dma/fsldma.h +++ b/drivers/dma/fsldma.h @@ -38,6 +38,7 @@ /* Special MR definition for MPC8349 */ #define FSL_DMA_MR_EOTIE 0x00000080 +#define FSL_DMA_MR_PRC_RM 0x00000800 #define FSL_DMA_SR_CH 0x00000020 #define FSL_DMA_SR_PE 0x00000010 -- GitLab From be30b226f2ae618cd719e40267d9923db1db9001 Mon Sep 17 00:00:00 2001 From: Ira Snyder Date: Thu, 28 May 2009 09:20:42 +0000 Subject: [PATCH 0002/1342] fsldma: enable external start for the 83xx controller The 83xx controller has external start capability, but lacks external pause capability. Hook up the external start function pointer for the 83xx controller. Signed-off-by: Ira W. Snyder Signed-off-by: Dan Williams --- drivers/dma/fsldma.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c index a1cb25e277b..10bcf0cb0ef 100644 --- a/drivers/dma/fsldma.c +++ b/drivers/dma/fsldma.c @@ -877,9 +877,9 @@ static int __devinit fsl_dma_chan_probe(struct fsl_dma_device *fdev, switch (new_fsl_chan->feature & FSL_DMA_IP_MASK) { case FSL_DMA_IP_85XX: - new_fsl_chan->toggle_ext_start = fsl_chan_toggle_ext_start; new_fsl_chan->toggle_ext_pause = fsl_chan_toggle_ext_pause; case FSL_DMA_IP_83XX: + new_fsl_chan->toggle_ext_start = fsl_chan_toggle_ext_start; new_fsl_chan->set_src_loop_size = fsl_chan_set_src_loop_size; new_fsl_chan->set_dest_loop_size = fsl_chan_set_dest_loop_size; } -- GitLab From 43a1a3ed6bf5a1b9ae197b4f5f20033baf19db61 Mon Sep 17 00:00:00 2001 From: Ira Snyder Date: Thu, 28 May 2009 09:26:40 +0000 Subject: [PATCH 0003/1342] fsldma: do not clear bandwidth control bits on the 83xx controller The 83xx controller does not support the external pause feature. The bit in the mode register that controls external pause on the 85xx controller happens to be part of the bandwidth control settings for the 83xx controller. This patch fixes the driver so that it only clears the external pause bit if the hardware is the 85xx controller. When driving the 83xx controller, the bit is left untouched. This follows the existing convention that mode registers settings are not touched unless necessary. Signed-off-by: Ira W. Snyder Signed-off-by: Dan Williams --- drivers/dma/fsldma.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c index 10bcf0cb0ef..6e60c77a145 100644 --- a/drivers/dma/fsldma.c +++ b/drivers/dma/fsldma.c @@ -147,10 +147,11 @@ static void dma_start(struct fsl_dma_chan *fsl_chan) if (fsl_chan->feature & FSL_DMA_CHAN_PAUSE_EXT) { DMA_OUT(fsl_chan, &fsl_chan->reg_base->bcr, 0, 32); mr_set |= FSL_DMA_MR_EMP_EN; - } else + } else if ((fsl_chan->feature & FSL_DMA_IP_MASK) == FSL_DMA_IP_85XX) { DMA_OUT(fsl_chan, &fsl_chan->reg_base->mr, DMA_IN(fsl_chan, &fsl_chan->reg_base->mr, 32) & ~FSL_DMA_MR_EMP_EN, 32); + } if (fsl_chan->feature & FSL_DMA_CHAN_START_EXT) mr_set |= FSL_DMA_MR_EMS_EN; -- GitLab From 4859484b0957ddc7fe3e0fa349d98b0f1c7876bd Mon Sep 17 00:00:00 2001 From: Jiri Slaby Date: Fri, 19 Jun 2009 23:24:11 +0200 Subject: [PATCH 0004/1342] HID: hiddev, fix lock imbalance Add omitted BKL to one switch/case. Cc: Stable Signed-off-by: Jiri Slaby Signed-off-by: Jiri Kosina --- drivers/hid/usbhid/hiddev.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/hid/usbhid/hiddev.c b/drivers/hid/usbhid/hiddev.c index e9b436d2d94..39e27f4be4a 100644 --- a/drivers/hid/usbhid/hiddev.c +++ b/drivers/hid/usbhid/hiddev.c @@ -527,8 +527,10 @@ static noinline int hiddev_ioctl_usage(struct hiddev *hiddev, unsigned int cmd, goto goodreturn; case HIDIOCGCOLLECTIONINDEX: + i = field->usage[uref->usage_index].collection_index; + unlock_kernel(); kfree(uref_multi); - return field->usage[uref->usage_index].collection_index; + return i; case HIDIOCGUSAGES: for (i = 0; i < uref_multi->num_values; i++) uref_multi->values[i] = -- GitLab From 04a820ead0838c76e9c1242feb5e71048bf3e9dc Mon Sep 17 00:00:00 2001 From: Andres Salomon Date: Tue, 30 Jun 2009 02:14:00 -0400 Subject: [PATCH 0005/1342] olpc_battery: Fix up eeprom read function The eeprom read function was placing values into the wrong place in 'buf'; we were starting from buf[off], rather than buf[0]. Also, the for loop that we were using was much uglier than it needed to be. This cleans it up a bit. Signed-off-by: Andres Salomon Signed-off-by: Anton Vorontsov --- drivers/power/olpc_battery.c | 17 +++++++++-------- 1 file changed, 9 insertions(+), 8 deletions(-) diff --git a/drivers/power/olpc_battery.c b/drivers/power/olpc_battery.c index 5fbca2681ba..9c216dd4155 100644 --- a/drivers/power/olpc_battery.c +++ b/drivers/power/olpc_battery.c @@ -8,6 +8,7 @@ * published by the Free Software Foundation. */ +#include #include #include #include @@ -334,21 +335,21 @@ static ssize_t olpc_bat_eeprom_read(struct kobject *kobj, struct bin_attribute *attr, char *buf, loff_t off, size_t count) { uint8_t ec_byte; - int ret, end; + int ret; + int i; if (off >= EEPROM_SIZE) return 0; if (off + count > EEPROM_SIZE) count = EEPROM_SIZE - off; - end = EEPROM_START + off + count; - for (ec_byte = EEPROM_START + off; ec_byte < end; ec_byte++) { - ret = olpc_ec_cmd(EC_BAT_EEPROM, &ec_byte, 1, - &buf[ec_byte - EEPROM_START], 1); + for (i = 0; i < count; i++) { + ec_byte = EEPROM_START + off + i; + ret = olpc_ec_cmd(EC_BAT_EEPROM, &ec_byte, 1, &buf[i], 1); if (ret) { - printk(KERN_ERR "olpc-battery: EC command " - "EC_BAT_EEPROM @ 0x%x failed -" - " %d!\n", ec_byte, ret); + pr_err("olpc-battery: " + "EC_BAT_EEPROM cmd @ 0x%x failed - %d!\n", + ec_byte, ret); return -EIO; } } -- GitLab From 8f7e57985fa794ab6afdcd3642581d9e1fe6de31 Mon Sep 17 00:00:00 2001 From: Andres Salomon Date: Tue, 30 Jun 2009 02:16:17 -0400 Subject: [PATCH 0006/1342] olpc_battery: Ensure that the TRICKLE bit is checked There are times when the battery is present but trickle charging, and the EC sets only the TRICKLE bit. So we must check for the bit when we're checking the charging/present status. Signed-off-by: Andres Salomon Signed-off-by: Anton Vorontsov --- drivers/power/olpc_battery.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) diff --git a/drivers/power/olpc_battery.c b/drivers/power/olpc_battery.c index 9c216dd4155..58e419299cd 100644 --- a/drivers/power/olpc_battery.c +++ b/drivers/power/olpc_battery.c @@ -36,6 +36,7 @@ #define BAT_STAT_AC 0x10 #define BAT_STAT_CHARGING 0x20 #define BAT_STAT_DISCHARGING 0x40 +#define BAT_STAT_TRICKLE 0x80 #define BAT_ERR_INFOFAIL 0x02 #define BAT_ERR_OVERVOLTAGE 0x04 @@ -90,7 +91,7 @@ static char bat_serial[17]; /* Ick */ static int olpc_bat_get_status(union power_supply_propval *val, uint8_t ec_byte) { if (olpc_platform_info.ecver > 0x44) { - if (ec_byte & BAT_STAT_CHARGING) + if (ec_byte & (BAT_STAT_CHARGING | BAT_STAT_TRICKLE)) val->intval = POWER_SUPPLY_STATUS_CHARGING; else if (ec_byte & BAT_STAT_DISCHARGING) val->intval = POWER_SUPPLY_STATUS_DISCHARGING; @@ -220,7 +221,8 @@ static int olpc_bat_get_property(struct power_supply *psy, It doesn't matter though -- the EC will return the last-known information, and it's as if we just ran that _little_ bit faster and managed to read it out before the battery went away. */ - if (!(ec_byte & BAT_STAT_PRESENT) && psp != POWER_SUPPLY_PROP_PRESENT) + if (!(ec_byte & (BAT_STAT_PRESENT | BAT_STAT_TRICKLE)) && + psp != POWER_SUPPLY_PROP_PRESENT) return -ENODEV; switch (psp) { @@ -230,7 +232,8 @@ static int olpc_bat_get_property(struct power_supply *psy, return ret; break; case POWER_SUPPLY_PROP_PRESENT: - val->intval = !!(ec_byte & BAT_STAT_PRESENT); + val->intval = !!(ec_byte & (BAT_STAT_PRESENT | + BAT_STAT_TRICKLE)); break; case POWER_SUPPLY_PROP_HEALTH: -- GitLab From bfdb46ce8494eae30dbaae65c81e684e6db6228b Mon Sep 17 00:00:00 2001 From: Ryan Mallon Date: Thu, 18 Jun 2009 11:26:26 +1200 Subject: [PATCH 0007/1342] Add ds2782 battery gas gauge driver This patch adds a driver for ds2782 battery devices. Signed-off-by: Ryan Mallon Signed-off-by: Anton Vorontsov --- drivers/power/Kconfig | 7 + drivers/power/Makefile | 1 + drivers/power/ds2782_battery.c | 330 +++++++++++++++++++++++++++++++++ 3 files changed, 338 insertions(+) create mode 100644 drivers/power/ds2782_battery.c diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig index 7eda34838bf..bdbc4f73fcd 100644 --- a/drivers/power/Kconfig +++ b/drivers/power/Kconfig @@ -43,6 +43,13 @@ config BATTERY_DS2760 help Say Y here to enable support for batteries with ds2760 chip. +config BATTERY_DS2782 + tristate "DS2782 standalone gas-gauge" + depends on I2C + help + Say Y here to enable support for the DS2782 standalone battery + gas-gauge. + config BATTERY_PMU tristate "Apple PMU battery" depends on PPC32 && ADB_PMU diff --git a/drivers/power/Makefile b/drivers/power/Makefile index daf3179689a..380d17c9ae2 100644 --- a/drivers/power/Makefile +++ b/drivers/power/Makefile @@ -19,6 +19,7 @@ obj-$(CONFIG_APM_POWER) += apm_power.o obj-$(CONFIG_WM8350_POWER) += wm8350_power.o obj-$(CONFIG_BATTERY_DS2760) += ds2760_battery.o +obj-$(CONFIG_BATTERY_DS2782) += ds2782_battery.o obj-$(CONFIG_BATTERY_PMU) += pmu_battery.o obj-$(CONFIG_BATTERY_OLPC) += olpc_battery.o obj-$(CONFIG_BATTERY_TOSA) += tosa_battery.o diff --git a/drivers/power/ds2782_battery.c b/drivers/power/ds2782_battery.c new file mode 100644 index 00000000000..da14f374cb6 --- /dev/null +++ b/drivers/power/ds2782_battery.c @@ -0,0 +1,330 @@ +/* + * I2C client/driver for the Maxim/Dallas DS2782 Stand-Alone Fuel Gauge IC + * + * Copyright (C) 2009 Bluewater Systems Ltd + * + * Author: Ryan Mallon + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#define DS2782_REG_RARC 0x06 /* Remaining active relative capacity */ + +#define DS2782_REG_VOLT_MSB 0x0c +#define DS2782_REG_TEMP_MSB 0x0a +#define DS2782_REG_CURRENT_MSB 0x0e + +/* EEPROM Block */ +#define DS2782_REG_RSNSP 0x69 /* Sense resistor value */ + +/* Current unit measurement in uA for a 1 milli-ohm sense resistor */ +#define DS2782_CURRENT_UNITS 1563 + +#define to_ds2782_info(x) container_of(x, struct ds2782_info, battery) + +struct ds2782_info { + struct i2c_client *client; + struct power_supply battery; + int id; +}; + +static DEFINE_IDR(battery_id); +static DEFINE_MUTEX(battery_lock); + +static inline int ds2782_read_reg(struct ds2782_info *info, int reg, u8 *val) +{ + int ret; + + ret = i2c_smbus_read_byte_data(info->client, reg); + if (ret < 0) { + dev_err(&info->client->dev, "register read failed\n"); + return ret; + } + + *val = ret; + return 0; +} + +static inline int ds2782_read_reg16(struct ds2782_info *info, int reg_msb, + s16 *val) +{ + int ret; + + ret = swab16(i2c_smbus_read_word_data(info->client, reg_msb)); + if (ret < 0) { + dev_err(&info->client->dev, "register read failed\n"); + return ret; + } + + *val = ret; + return 0; +} + +static int ds2782_get_temp(struct ds2782_info *info, int *temp) +{ + s16 raw; + int err; + + /* + * Temperature is measured in units of 0.125 degrees celcius, the + * power_supply class measures temperature in tenths of degrees + * celsius. The temperature value is stored as a 10 bit number, plus + * sign in the upper bits of a 16 bit register. + */ + err = ds2782_read_reg16(info, DS2782_REG_TEMP_MSB, &raw); + if (err) + return err; + *temp = ((raw / 32) * 125) / 100; + return 0; +} + +static int ds2782_get_current(struct ds2782_info *info, int *current_uA) +{ + int sense_res; + int err; + u8 sense_res_raw; + s16 raw; + + /* + * The units of measurement for current are dependent on the value of + * the sense resistor. + */ + err = ds2782_read_reg(info, DS2782_REG_RSNSP, &sense_res_raw); + if (err) + return err; + if (sense_res_raw == 0) { + dev_err(&info->client->dev, "sense resistor value is 0\n"); + return -ENXIO; + } + sense_res = 1000 / sense_res_raw; + + dev_dbg(&info->client->dev, "sense resistor = %d milli-ohms\n", + sense_res); + err = ds2782_read_reg16(info, DS2782_REG_CURRENT_MSB, &raw); + if (err) + return err; + *current_uA = raw * (DS2782_CURRENT_UNITS / sense_res); + return 0; +} + +static int ds2782_get_voltage(struct ds2782_info *info, int *voltage_uA) +{ + s16 raw; + int err; + + /* + * Voltage is measured in units of 4.88mV. The voltage is stored as + * a 10-bit number plus sign, in the upper bits of a 16-bit register + */ + err = ds2782_read_reg16(info, DS2782_REG_VOLT_MSB, &raw); + if (err) + return err; + *voltage_uA = (raw / 32) * 4800; + return 0; +} + +static int ds2782_get_capacity(struct ds2782_info *info, int *capacity) +{ + int err; + u8 raw; + + err = ds2782_read_reg(info, DS2782_REG_RARC, &raw); + if (err) + return err; + *capacity = raw; + return raw; +} + +static int ds2782_get_status(struct ds2782_info *info, int *status) +{ + int err; + int current_uA; + int capacity; + + err = ds2782_get_current(info, ¤t_uA); + if (err) + return err; + + err = ds2782_get_capacity(info, &capacity); + if (err) + return err; + + if (capacity == 100) + *status = POWER_SUPPLY_STATUS_FULL; + else if (current_uA == 0) + *status = POWER_SUPPLY_STATUS_NOT_CHARGING; + else if (current_uA < 0) + *status = POWER_SUPPLY_STATUS_DISCHARGING; + else + *status = POWER_SUPPLY_STATUS_CHARGING; + + return 0; +} + +static int ds2782_battery_get_property(struct power_supply *psy, + enum power_supply_property prop, + union power_supply_propval *val) +{ + struct ds2782_info *info = to_ds2782_info(psy); + int ret; + + switch (prop) { + case POWER_SUPPLY_PROP_STATUS: + ret = ds2782_get_status(info, &val->intval); + break; + + case POWER_SUPPLY_PROP_CAPACITY: + ret = ds2782_get_capacity(info, &val->intval); + break; + + case POWER_SUPPLY_PROP_VOLTAGE_NOW: + ret = ds2782_get_voltage(info, &val->intval); + break; + + case POWER_SUPPLY_PROP_CURRENT_NOW: + ret = ds2782_get_current(info, &val->intval); + break; + + case POWER_SUPPLY_PROP_TEMP: + ret = ds2782_get_temp(info, &val->intval); + break; + + default: + ret = -EINVAL; + } + + return ret; +} + +static enum power_supply_property ds2782_battery_props[] = { + POWER_SUPPLY_PROP_STATUS, + POWER_SUPPLY_PROP_CAPACITY, + POWER_SUPPLY_PROP_VOLTAGE_NOW, + POWER_SUPPLY_PROP_CURRENT_NOW, + POWER_SUPPLY_PROP_TEMP, +}; + +static void ds2782_power_supply_init(struct power_supply *battery) +{ + battery->type = POWER_SUPPLY_TYPE_BATTERY; + battery->properties = ds2782_battery_props; + battery->num_properties = ARRAY_SIZE(ds2782_battery_props); + battery->get_property = ds2782_battery_get_property; + battery->external_power_changed = NULL; +} + +static int ds2782_battery_remove(struct i2c_client *client) +{ + struct ds2782_info *info = i2c_get_clientdata(client); + + power_supply_unregister(&info->battery); + kfree(info->battery.name); + + mutex_lock(&battery_lock); + idr_remove(&battery_id, info->id); + mutex_unlock(&battery_lock); + + i2c_set_clientdata(client, info); + + kfree(info); + return 0; +} + +static int ds2782_battery_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct ds2782_info *info; + int ret; + int num; + + /* Get an ID for this battery */ + ret = idr_pre_get(&battery_id, GFP_KERNEL); + if (ret == 0) { + ret = -ENOMEM; + goto fail_id; + } + + mutex_lock(&battery_lock); + ret = idr_get_new(&battery_id, client, &num); + mutex_unlock(&battery_lock); + if (ret < 0) + goto fail_id; + + info = kzalloc(sizeof(*info), GFP_KERNEL); + if (!info) { + ret = -ENOMEM; + goto fail_info; + } + + info->battery.name = kasprintf(GFP_KERNEL, "ds2782-%d", num); + if (!info->battery.name) { + ret = -ENOMEM; + goto fail_name; + } + + i2c_set_clientdata(client, info); + info->client = client; + ds2782_power_supply_init(&info->battery); + + ret = power_supply_register(&client->dev, &info->battery); + if (ret) { + dev_err(&client->dev, "failed to register battery\n"); + goto fail_register; + } + + return 0; + +fail_register: + kfree(info->battery.name); +fail_name: + i2c_set_clientdata(client, info); + kfree(info); +fail_info: + mutex_lock(&battery_lock); + idr_remove(&battery_id, num); + mutex_unlock(&battery_lock); +fail_id: + return ret; +} + +static const struct i2c_device_id ds2782_id[] = { + {"ds2782", 0}, + {}, +}; + +static struct i2c_driver ds2782_battery_driver = { + .driver = { + .name = "ds2782-battery", + }, + .probe = ds2782_battery_probe, + .remove = ds2782_battery_remove, + .id_table = ds2782_id, +}; + +static int __init ds2782_init(void) +{ + return i2c_add_driver(&ds2782_battery_driver); +} +module_init(ds2782_init); + +static void __exit ds2782_exit(void) +{ + i2c_del_driver(&ds2782_battery_driver); +} +module_exit(ds2782_exit); + +MODULE_AUTHOR("Ryan Mallon "); +MODULE_DESCRIPTION("Maxim/Dallas DS2782 Stand-Alone Fuel Gauage IC driver"); +MODULE_LICENSE("GPL"); -- GitLab From 3f1f7cf08ddf10ef7fbf06d881582c95b9747f4e Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 1 Jul 2009 11:32:10 +0200 Subject: [PATCH 0008/1342] netfilter: add netfilter git to MAINTAINERS Signed-off-by: Joe Perches Signed-off-by: Patrick McHardy --- MAINTAINERS | 1 + 1 file changed, 1 insertion(+) diff --git a/MAINTAINERS b/MAINTAINERS index fa2a16def17..a5042dea134 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -4044,6 +4044,7 @@ L: netfilter@vger.kernel.org L: coreteam@netfilter.org W: http://www.netfilter.org/ W: http://www.iptables.org/ +T: git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-2.6.git S: Supported F: include/linux/netfilter* F: include/linux/netfilter/ -- GitLab From daf4219dbcbb2efcd638fcd3c29a622e1c18cc38 Mon Sep 17 00:00:00 2001 From: Dan Williams Date: Wed, 1 Jul 2009 16:12:53 -0700 Subject: [PATCH 0009/1342] dmaengine: move HIGHMEM64G restriction to ASYNC_TX_DMA On HIGHMEM64G systems dma_addr_t is known to be larger than (void *) which precludes async_xor from performing dma address conversions by reusing the input parameter address list. However, other parts of the dmaengine infrastructure do not suffer this constraint, so the HIGHMEM64G restriction can be down-levelled. Signed-off-by: Dan Williams --- crypto/async_tx/async_xor.c | 2 +- drivers/dma/Kconfig | 4 ++-- 2 files changed, 3 insertions(+), 3 deletions(-) diff --git a/crypto/async_tx/async_xor.c b/crypto/async_tx/async_xor.c index 95fe2c8d6c5..90dd3f8bd28 100644 --- a/crypto/async_tx/async_xor.c +++ b/crypto/async_tx/async_xor.c @@ -300,7 +300,7 @@ EXPORT_SYMBOL_GPL(async_xor_zero_sum); static int __init async_xor_init(void) { - #ifdef CONFIG_DMA_ENGINE + #ifdef CONFIG_ASYNC_TX_DMA /* To conserve stack space the input src_list (array of page pointers) * is reused to hold the array of dma addresses passed to the driver. * This conversion is only possible when dma_addr_t is less than the diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig index 3b3c01b6f1e..babf214a509 100644 --- a/drivers/dma/Kconfig +++ b/drivers/dma/Kconfig @@ -4,7 +4,7 @@ menuconfig DMADEVICES bool "DMA Engine support" - depends on !HIGHMEM64G && HAS_DMA + depends on HAS_DMA help DMA engines can do asynchronous data transfers without involving the host CPU. Currently, this framework can be @@ -100,7 +100,7 @@ config NET_DMA config ASYNC_TX_DMA bool "Async_tx: Offload support for the async_tx api" - depends on DMA_ENGINE + depends on DMA_ENGINE && !HIGHMEM64G help This allows the async_tx api to take advantage of offload engines for memcpy, memset, xor, and raid6 p+q operations. If your platform has -- GitLab From 8b712cd58adfe6aeeb0be4ecc011dc35620719e7 Mon Sep 17 00:00:00 2001 From: Jeff Mahoney Date: Tue, 7 Jul 2009 17:22:12 -0400 Subject: [PATCH 0010/1342] ocfs2: Fixup orphan scan cleanup after failed mount If the mount fails for any reason, ocfs2_dismount_volume calls ocfs2_orphan_scan_stop. It requires that ocfs2_orphan_scan_init be called to setup the mutex and work queues, but that doesn't happen if the mount has failed and we oops accessing an uninitialized work queue. This patch splits the init and startup of the orphan scan, eliminating the oops. Signed-off-by: Jeff Mahoney Signed-off-by: Joel Becker --- fs/ocfs2/journal.c | 8 +++++++- fs/ocfs2/journal.h | 1 + fs/ocfs2/super.c | 4 +++- 3 files changed, 11 insertions(+), 2 deletions(-) diff --git a/fs/ocfs2/journal.c b/fs/ocfs2/journal.c index f033760ecbe..c48b93ac6b6 100644 --- a/fs/ocfs2/journal.c +++ b/fs/ocfs2/journal.c @@ -1954,10 +1954,16 @@ void ocfs2_orphan_scan_init(struct ocfs2_super *osb) os->os_osb = osb; os->os_count = 0; os->os_seqno = 0; - os->os_scantime = CURRENT_TIME; mutex_init(&os->os_lock); INIT_DELAYED_WORK(&os->os_orphan_scan_work, ocfs2_orphan_scan_work); +} +void ocfs2_orphan_scan_start(struct ocfs2_super *osb) +{ + struct ocfs2_orphan_scan *os; + + os = &osb->osb_orphan_scan; + os->os_scantime = CURRENT_TIME; if (ocfs2_is_hard_readonly(osb) || ocfs2_mount_local(osb)) atomic_set(&os->os_state, ORPHAN_SCAN_INACTIVE); else { diff --git a/fs/ocfs2/journal.h b/fs/ocfs2/journal.h index 5432c7f79cc..81e8abcd246 100644 --- a/fs/ocfs2/journal.h +++ b/fs/ocfs2/journal.h @@ -145,6 +145,7 @@ static inline void ocfs2_inode_set_new(struct ocfs2_super *osb, /* Exported only for the journal struct init code in super.c. Do not call. */ void ocfs2_orphan_scan_init(struct ocfs2_super *osb); +void ocfs2_orphan_scan_start(struct ocfs2_super *osb); void ocfs2_orphan_scan_stop(struct ocfs2_super *osb); void ocfs2_orphan_scan_exit(struct ocfs2_super *osb); diff --git a/fs/ocfs2/super.c b/fs/ocfs2/super.c index 7efb349fb9b..63af2e36d83 100644 --- a/fs/ocfs2/super.c +++ b/fs/ocfs2/super.c @@ -1182,7 +1182,7 @@ static int ocfs2_fill_super(struct super_block *sb, void *data, int silent) wake_up(&osb->osb_mount_event); /* Start this when the mount is almost sure of being successful */ - ocfs2_orphan_scan_init(osb); + ocfs2_orphan_scan_start(osb); mlog_exit(status); return status; @@ -1981,6 +1981,8 @@ static int ocfs2_initialize_super(struct super_block *sb, snprintf(osb->dev_str, sizeof(osb->dev_str), "%u,%u", MAJOR(osb->sb->s_dev), MINOR(osb->sb->s_dev)); + ocfs2_orphan_scan_init(osb); + status = ocfs2_recovery_init(osb); if (status) { mlog(ML_ERROR, "Unable to initialize recovery state\n"); -- GitLab From 17ae26b669886efe237b77439e43eb390fceb119 Mon Sep 17 00:00:00 2001 From: Jeff Liu Date: Tue, 7 Jul 2009 15:51:40 +0800 Subject: [PATCH 0011/1342] ocfs2: trivial fix for s/migrate/migration/ in dlmrecovery.c logging in dlmrecovery.c:1121, replace 'migrate' to 'migration' to keep the consistency by comparing to other lines with the similar log info in the same file. Signed-off-by: Jeff Liu Signed-off-by: Joel Becker --- fs/ocfs2/dlm/dlmrecovery.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/ocfs2/dlm/dlmrecovery.c b/fs/ocfs2/dlm/dlmrecovery.c index bcb9260c373..43e6e328056 100644 --- a/fs/ocfs2/dlm/dlmrecovery.c +++ b/fs/ocfs2/dlm/dlmrecovery.c @@ -1118,7 +1118,7 @@ static int dlm_send_mig_lockres_msg(struct dlm_ctxt *dlm, mlog(0, "%s:%.*s: sending mig lockres (%s) to %u\n", dlm->name, res->lockname.len, res->lockname.name, - orig_flags & DLM_MRES_MIGRATION ? "migrate" : "recovery", + orig_flags & DLM_MRES_MIGRATION ? "migration" : "recovery", send_to); /* send it */ -- GitLab From 9590b7ba3fefdfe0c7741f5e2f61faf2ffcea19c Mon Sep 17 00:00:00 2001 From: Anton Blanchard Date: Mon, 6 Jul 2009 22:01:31 +1000 Subject: [PATCH 0012/1342] perf_counter tools: Rename cache events to remove $ The cache events contain '$' which will hit shell variable expansion. To avoid confusion change this to 'cache', ie L1-d$-loads becomes L1-dcache-loads. Signed-off-by: Anton Blanchard Cc: Roland Dreier Cc: Jaswinder Singh Rajput Cc: Peter Zijlstra LKML-Reference: <20090706120131.GB4391@kryten> Signed-off-by: Ingo Molnar --- tools/perf/util/parse-events.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/tools/perf/util/parse-events.c b/tools/perf/util/parse-events.c index 5184959e061..518a33affe1 100644 --- a/tools/perf/util/parse-events.c +++ b/tools/perf/util/parse-events.c @@ -71,8 +71,8 @@ static char *sw_event_names[] = { #define MAX_ALIASES 8 static char *hw_cache[][MAX_ALIASES] = { - { "L1-d$", "l1-d", "l1d", "L1-data", }, - { "L1-i$", "l1-i", "l1i", "L1-instruction", }, + { "L1-dcache", "l1-d", "l1d", "L1-data", }, + { "L1-icache", "l1-i", "l1i", "L1-instruction", }, { "LLC", "L2" }, { "dTLB", "d-tlb", "Data-TLB", }, { "iTLB", "i-tlb", "Instruction-TLB", }, -- GitLab From 11d1578f9454159c43499d1d8fe8a7d728c176a3 Mon Sep 17 00:00:00 2001 From: Vince Weaver Date: Wed, 8 Jul 2009 17:46:14 -0400 Subject: [PATCH 0013/1342] perf_counter: Add P6 PMU support Add basic P6 PMU support. The P6 uses the EVNTSEL0 EN bit to enable/disable both its counters. We use this for the global enable/disable, and clear all config bits (except EN) to disable individual counters. Actual ia32 hardware doesn't support lfence, so use a locked op without side-effect to implement a full barrier. perf stat and perf record seem to function correctly. [a.p.zijlstra@chello.nl: cleanups and complete the enable/disable code] Signed-off-by: Vince Weaver Signed-off-by: Peter Zijlstra LKML-Reference: Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/perf_counter.c | 227 +++++++++++++++++++++++++++-- tools/perf/perf.h | 8 +- 2 files changed, 220 insertions(+), 15 deletions(-) diff --git a/arch/x86/kernel/cpu/perf_counter.c b/arch/x86/kernel/cpu/perf_counter.c index 36c3dc7b899..1910f39ff19 100644 --- a/arch/x86/kernel/cpu/perf_counter.c +++ b/arch/x86/kernel/cpu/perf_counter.c @@ -65,6 +65,44 @@ static DEFINE_PER_CPU(struct cpu_hw_counters, cpu_hw_counters) = { .enabled = 1, }; +/* + * Not sure about some of these + */ +static const u64 p6_perfmon_event_map[] = +{ + [PERF_COUNT_HW_CPU_CYCLES] = 0x0079, + [PERF_COUNT_HW_INSTRUCTIONS] = 0x00c0, + [PERF_COUNT_HW_CACHE_REFERENCES] = 0x0000, + [PERF_COUNT_HW_CACHE_MISSES] = 0x0000, + [PERF_COUNT_HW_BRANCH_INSTRUCTIONS] = 0x00c4, + [PERF_COUNT_HW_BRANCH_MISSES] = 0x00c5, + [PERF_COUNT_HW_BUS_CYCLES] = 0x0062, +}; + +static u64 p6_pmu_event_map(int event) +{ + return p6_perfmon_event_map[event]; +} + +static u64 p6_pmu_raw_event(u64 event) +{ +#define P6_EVNTSEL_EVENT_MASK 0x000000FFULL +#define P6_EVNTSEL_UNIT_MASK 0x0000FF00ULL +#define P6_EVNTSEL_EDGE_MASK 0x00040000ULL +#define P6_EVNTSEL_INV_MASK 0x00800000ULL +#define P6_EVNTSEL_COUNTER_MASK 0xFF000000ULL + +#define P6_EVNTSEL_MASK \ + (P6_EVNTSEL_EVENT_MASK | \ + P6_EVNTSEL_UNIT_MASK | \ + P6_EVNTSEL_EDGE_MASK | \ + P6_EVNTSEL_INV_MASK | \ + P6_EVNTSEL_COUNTER_MASK) + + return event & P6_EVNTSEL_MASK; +} + + /* * Intel PerfMon v3. Used on Core2 and later. */ @@ -726,6 +764,23 @@ static int __hw_perf_counter_init(struct perf_counter *counter) return 0; } +static void p6_pmu_disable_all(void) +{ + struct cpu_hw_counters *cpuc = &__get_cpu_var(cpu_hw_counters); + unsigned long val; + + if (!cpuc->enabled) + return; + + cpuc->enabled = 0; + barrier(); + + /* p6 only has one enable register */ + rdmsrl(MSR_P6_EVNTSEL0, val); + val &= ~ARCH_PERFMON_EVENTSEL0_ENABLE; + wrmsrl(MSR_P6_EVNTSEL0, val); +} + static void intel_pmu_disable_all(void) { wrmsrl(MSR_CORE_PERF_GLOBAL_CTRL, 0); @@ -767,6 +822,23 @@ void hw_perf_disable(void) return x86_pmu.disable_all(); } +static void p6_pmu_enable_all(void) +{ + struct cpu_hw_counters *cpuc = &__get_cpu_var(cpu_hw_counters); + unsigned long val; + + if (cpuc->enabled) + return; + + cpuc->enabled = 1; + barrier(); + + /* p6 only has one enable register */ + rdmsrl(MSR_P6_EVNTSEL0, val); + val |= ARCH_PERFMON_EVENTSEL0_ENABLE; + wrmsrl(MSR_P6_EVNTSEL0, val); +} + static void intel_pmu_enable_all(void) { wrmsrl(MSR_CORE_PERF_GLOBAL_CTRL, x86_pmu.intel_ctrl); @@ -819,16 +891,13 @@ static inline void intel_pmu_ack_status(u64 ack) static inline void x86_pmu_enable_counter(struct hw_perf_counter *hwc, int idx) { - int err; - err = checking_wrmsrl(hwc->config_base + idx, + (void)checking_wrmsrl(hwc->config_base + idx, hwc->config | ARCH_PERFMON_EVENTSEL0_ENABLE); } static inline void x86_pmu_disable_counter(struct hw_perf_counter *hwc, int idx) { - int err; - err = checking_wrmsrl(hwc->config_base + idx, - hwc->config); + (void)checking_wrmsrl(hwc->config_base + idx, hwc->config); } static inline void @@ -836,13 +905,24 @@ intel_pmu_disable_fixed(struct hw_perf_counter *hwc, int __idx) { int idx = __idx - X86_PMC_IDX_FIXED; u64 ctrl_val, mask; - int err; mask = 0xfULL << (idx * 4); rdmsrl(hwc->config_base, ctrl_val); ctrl_val &= ~mask; - err = checking_wrmsrl(hwc->config_base, ctrl_val); + (void)checking_wrmsrl(hwc->config_base, ctrl_val); +} + +static inline void +p6_pmu_disable_counter(struct hw_perf_counter *hwc, int idx) +{ + struct cpu_hw_counters *cpuc = &__get_cpu_var(cpu_hw_counters); + unsigned long val = ARCH_PERFMON_EVENTSEL0_ENABLE; + + if (!cpuc->enabled) + val = 0; + + (void)checking_wrmsrl(hwc->config_base + idx, val); } static inline void @@ -943,6 +1023,17 @@ intel_pmu_enable_fixed(struct hw_perf_counter *hwc, int __idx) err = checking_wrmsrl(hwc->config_base, ctrl_val); } +static void p6_pmu_enable_counter(struct hw_perf_counter *hwc, int idx) +{ + struct cpu_hw_counters *cpuc = &__get_cpu_var(cpu_hw_counters); + + if (cpuc->enabled) + x86_pmu_enable_counter(hwc, idx); + else + x86_pmu_disable_counter(hwc, idx); +} + + static void intel_pmu_enable_counter(struct hw_perf_counter *hwc, int idx) { if (unlikely(hwc->config_base == MSR_ARCH_PERFMON_FIXED_CTR_CTRL)) { @@ -1176,6 +1267,49 @@ static void intel_pmu_reset(void) local_irq_restore(flags); } +static int p6_pmu_handle_irq(struct pt_regs *regs) +{ + struct perf_sample_data data; + struct cpu_hw_counters *cpuc; + struct perf_counter *counter; + struct hw_perf_counter *hwc; + int idx, handled = 0; + u64 val; + + data.regs = regs; + data.addr = 0; + + cpuc = &__get_cpu_var(cpu_hw_counters); + + for (idx = 0; idx < x86_pmu.num_counters; idx++) { + if (!test_bit(idx, cpuc->active_mask)) + continue; + + counter = cpuc->counters[idx]; + hwc = &counter->hw; + + val = x86_perf_counter_update(counter, hwc, idx); + if (val & (1ULL << (x86_pmu.counter_bits - 1))) + continue; + + /* + * counter overflow + */ + handled = 1; + data.period = counter->hw.last_period; + + if (!x86_perf_counter_set_period(counter, hwc, idx)) + continue; + + if (perf_counter_overflow(counter, 1, &data)) + p6_pmu_disable_counter(hwc, idx); + } + + if (handled) + inc_irq_stat(apic_perf_irqs); + + return handled; +} /* * This handler is triggered by the local APIC, so the APIC IRQ handling @@ -1185,14 +1319,13 @@ static int intel_pmu_handle_irq(struct pt_regs *regs) { struct perf_sample_data data; struct cpu_hw_counters *cpuc; - int bit, cpu, loops; + int bit, loops; u64 ack, status; data.regs = regs; data.addr = 0; - cpu = smp_processor_id(); - cpuc = &per_cpu(cpu_hw_counters, cpu); + cpuc = &__get_cpu_var(cpu_hw_counters); perf_disable(); status = intel_pmu_get_status(); @@ -1249,14 +1382,13 @@ static int amd_pmu_handle_irq(struct pt_regs *regs) struct cpu_hw_counters *cpuc; struct perf_counter *counter; struct hw_perf_counter *hwc; - int cpu, idx, handled = 0; + int idx, handled = 0; u64 val; data.regs = regs; data.addr = 0; - cpu = smp_processor_id(); - cpuc = &per_cpu(cpu_hw_counters, cpu); + cpuc = &__get_cpu_var(cpu_hw_counters); for (idx = 0; idx < x86_pmu.num_counters; idx++) { if (!test_bit(idx, cpuc->active_mask)) @@ -1353,6 +1485,32 @@ static __read_mostly struct notifier_block perf_counter_nmi_notifier = { .priority = 1 }; +static struct x86_pmu p6_pmu = { + .name = "p6", + .handle_irq = p6_pmu_handle_irq, + .disable_all = p6_pmu_disable_all, + .enable_all = p6_pmu_enable_all, + .enable = p6_pmu_enable_counter, + .disable = p6_pmu_disable_counter, + .eventsel = MSR_P6_EVNTSEL0, + .perfctr = MSR_P6_PERFCTR0, + .event_map = p6_pmu_event_map, + .raw_event = p6_pmu_raw_event, + .max_events = ARRAY_SIZE(p6_perfmon_event_map), + .max_period = (1ULL << 31) - 1, + .version = 0, + .num_counters = 2, + /* + * Counters have 40 bits implemented. However they are designed such + * that bits [32-39] are sign extensions of bit 31. As such the + * effective width of a counter for P6-like PMU is 32 bits only. + * + * See IA-32 Intel Architecture Software developer manual Vol 3B + */ + .counter_bits = 32, + .counter_mask = (1ULL << 32) - 1, +}; + static struct x86_pmu intel_pmu = { .name = "Intel", .handle_irq = intel_pmu_handle_irq, @@ -1392,6 +1550,41 @@ static struct x86_pmu amd_pmu = { .max_period = (1ULL << 47) - 1, }; +static int p6_pmu_init(void) +{ + int high, low; + + switch (boot_cpu_data.x86_model) { + case 1: + case 3: /* Pentium Pro */ + case 5: + case 6: /* Pentium II */ + case 7: + case 8: + case 11: /* Pentium III */ + break; + case 9: + case 13: + /* for Pentium M, we need to check if PMU exist */ + rdmsr(MSR_IA32_MISC_ENABLE, low, high); + if (low & MSR_IA32_MISC_ENABLE_EMON) + break; + default: + pr_cont("unsupported p6 CPU model %d ", + boot_cpu_data.x86_model); + return -ENODEV; + } + + if (!cpu_has_apic) { + pr_info("no Local APIC, try rebooting with lapic"); + return -ENODEV; + } + + x86_pmu = p6_pmu; + + return 0; +} + static int intel_pmu_init(void) { union cpuid10_edx edx; @@ -1400,8 +1593,14 @@ static int intel_pmu_init(void) unsigned int ebx; int version; - if (!cpu_has(&boot_cpu_data, X86_FEATURE_ARCH_PERFMON)) + if (!cpu_has(&boot_cpu_data, X86_FEATURE_ARCH_PERFMON)) { + /* check for P6 processor family */ + if (boot_cpu_data.x86 == 6) { + return p6_pmu_init(); + } else { return -ENODEV; + } + } /* * Check whether the Architectural PerfMon supports diff --git a/tools/perf/perf.h b/tools/perf/perf.h index 27887c91643..53bb9550def 100644 --- a/tools/perf/perf.h +++ b/tools/perf/perf.h @@ -1,7 +1,13 @@ #ifndef _PERF_PERF_H #define _PERF_PERF_H -#if defined(__x86_64__) || defined(__i386__) +#if defined(__i386__) +#include "../../arch/x86/include/asm/unistd.h" +#define rmb() asm volatile("lock; addl $0,0(%%esp)" ::: "memory") +#define cpu_relax() asm volatile("rep; nop" ::: "memory"); +#endif + +#if defined(__x86_64__) #include "../../arch/x86/include/asm/unistd.h" #define rmb() asm volatile("lfence" ::: "memory") #define cpu_relax() asm volatile("rep; nop" ::: "memory"); -- GitLab From 9c74fb50867e8fb5f3be3be06716492c0f79309e Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Wed, 8 Jul 2009 10:21:41 +0200 Subject: [PATCH 0014/1342] perf_counter: Fix up P6 PMU details The P6 doesn't seem to support cache ref/hit/miss counts, so we extend the generic hardware event codes to have 0 and -1 mean the same thing as for the generic cache events. Furthermore, it turns out the 0 event does not count (that is, its reported that on PPro it actually does count something), therefore use a event configuration that's specified not to count to disable the counters. Signed-off-by: Peter Zijlstra LKML-Reference: Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/perf_counter.c | 28 +++++++++++++++++++++++----- 1 file changed, 23 insertions(+), 5 deletions(-) diff --git a/arch/x86/kernel/cpu/perf_counter.c b/arch/x86/kernel/cpu/perf_counter.c index 1910f39ff19..c7cc6eac14e 100644 --- a/arch/x86/kernel/cpu/perf_counter.c +++ b/arch/x86/kernel/cpu/perf_counter.c @@ -84,6 +84,14 @@ static u64 p6_pmu_event_map(int event) return p6_perfmon_event_map[event]; } +/* + * Counter setting that is specified not to count anything. + * We use this to effectively disable a counter. + * + * L2_RQSTS with 0 MESI unit mask. + */ +#define P6_NOP_COUNTER 0x0000002EULL + static u64 p6_pmu_raw_event(u64 event) { #define P6_EVNTSEL_EVENT_MASK 0x000000FFULL @@ -704,6 +712,7 @@ static int __hw_perf_counter_init(struct perf_counter *counter) { struct perf_counter_attr *attr = &counter->attr; struct hw_perf_counter *hwc = &counter->hw; + u64 config; int err; if (!x86_pmu_initialized()) @@ -756,10 +765,19 @@ static int __hw_perf_counter_init(struct perf_counter *counter) if (attr->config >= x86_pmu.max_events) return -EINVAL; + /* * The generic map: */ - hwc->config |= x86_pmu.event_map(attr->config); + config = x86_pmu.event_map(attr->config); + + if (config == 0) + return -ENOENT; + + if (config == -1LL) + return -EINVAL; + + hwc->config |= config; return 0; } @@ -767,7 +785,7 @@ static int __hw_perf_counter_init(struct perf_counter *counter) static void p6_pmu_disable_all(void) { struct cpu_hw_counters *cpuc = &__get_cpu_var(cpu_hw_counters); - unsigned long val; + u64 val; if (!cpuc->enabled) return; @@ -917,10 +935,10 @@ static inline void p6_pmu_disable_counter(struct hw_perf_counter *hwc, int idx) { struct cpu_hw_counters *cpuc = &__get_cpu_var(cpu_hw_counters); - unsigned long val = ARCH_PERFMON_EVENTSEL0_ENABLE; + u64 val = P6_NOP_COUNTER; - if (!cpuc->enabled) - val = 0; + if (cpuc->enabled) + val |= ARCH_PERFMON_EVENTSEL0_ENABLE; (void)checking_wrmsrl(hwc->config_base + idx, val); } -- GitLab From 984b838ce69c063a91b87550598ab7f3439dd94a Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Fri, 10 Jul 2009 09:59:56 +0200 Subject: [PATCH 0015/1342] perf_counter: Clean up global vs counter enable Ingo noticed that both AMD and P6 call x86_pmu_disable_counter() on *_pmu_enable_counter(). This is because we rely on the side effect of that call to program the event config but not touch the EN bit. We change that for AMD by having enable_all() simply write the full config in, and for P6 by explicitly coding it. Signed-off-by: Peter Zijlstra LKML-Reference: Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/perf_counter.c | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) diff --git a/arch/x86/kernel/cpu/perf_counter.c b/arch/x86/kernel/cpu/perf_counter.c index c7cc6eac14e..bed1c4c2f25 100644 --- a/arch/x86/kernel/cpu/perf_counter.c +++ b/arch/x86/kernel/cpu/perf_counter.c @@ -874,13 +874,13 @@ static void amd_pmu_enable_all(void) barrier(); for (idx = 0; idx < x86_pmu.num_counters; idx++) { + struct perf_counter *counter = cpuc->counters[idx]; u64 val; if (!test_bit(idx, cpuc->active_mask)) continue; - rdmsrl(MSR_K7_EVNTSEL0 + idx, val); - if (val & ARCH_PERFMON_EVENTSEL0_ENABLE) - continue; + + val = counter->hw.config; val |= ARCH_PERFMON_EVENTSEL0_ENABLE; wrmsrl(MSR_K7_EVNTSEL0 + idx, val); } @@ -1044,11 +1044,13 @@ intel_pmu_enable_fixed(struct hw_perf_counter *hwc, int __idx) static void p6_pmu_enable_counter(struct hw_perf_counter *hwc, int idx) { struct cpu_hw_counters *cpuc = &__get_cpu_var(cpu_hw_counters); + u64 val; + val = hwc->config; if (cpuc->enabled) - x86_pmu_enable_counter(hwc, idx); - else - x86_pmu_disable_counter(hwc, idx); + val |= ARCH_PERFMON_EVENTSEL0_ENABLE; + + (void)checking_wrmsrl(hwc->config_base + idx, val); } @@ -1068,8 +1070,6 @@ static void amd_pmu_enable_counter(struct hw_perf_counter *hwc, int idx) if (cpuc->enabled) x86_pmu_enable_counter(hwc, idx); - else - x86_pmu_disable_counter(hwc, idx); } static int -- GitLab From 71a851b4d2a815adcfac09c1adda7ef6811fde66 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Fri, 10 Jul 2009 09:06:56 +0200 Subject: [PATCH 0016/1342] perf_counter: Stop open coding unclone_ctx Instead of open coding the unclone context thingy, put it in a common function. Signed-off-by: Peter Zijlstra LKML-Reference: Signed-off-by: Ingo Molnar --- kernel/perf_counter.c | 36 +++++++++++++++++------------------- 1 file changed, 17 insertions(+), 19 deletions(-) diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index d55a50da234..8bf997d86bf 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -146,6 +146,14 @@ static void put_ctx(struct perf_counter_context *ctx) } } +static void unclone_ctx(struct perf_counter_context *ctx) +{ + if (ctx->parent_ctx) { + put_ctx(ctx->parent_ctx); + ctx->parent_ctx = NULL; + } +} + /* * Get the perf_counter_context for a task and lock it. * This has to cope with with the fact that until it is locked, @@ -1463,10 +1471,8 @@ static void perf_counter_enable_on_exec(struct task_struct *task) /* * Unclone this context if we enabled any counter. */ - if (enabled && ctx->parent_ctx) { - put_ctx(ctx->parent_ctx); - ctx->parent_ctx = NULL; - } + if (enabled) + unclone_ctx(ctx); spin_unlock(&ctx->lock); @@ -1526,7 +1532,6 @@ __perf_counter_init_context(struct perf_counter_context *ctx, static struct perf_counter_context *find_get_context(pid_t pid, int cpu) { - struct perf_counter_context *parent_ctx; struct perf_counter_context *ctx; struct perf_cpu_context *cpuctx; struct task_struct *task; @@ -1586,11 +1591,7 @@ static struct perf_counter_context *find_get_context(pid_t pid, int cpu) retry: ctx = perf_lock_task_context(task, &flags); if (ctx) { - parent_ctx = ctx->parent_ctx; - if (parent_ctx) { - put_ctx(parent_ctx); - ctx->parent_ctx = NULL; /* no longer a clone */ - } + unclone_ctx(ctx); spin_unlock_irqrestore(&ctx->lock, flags); } @@ -4255,15 +4256,12 @@ void perf_counter_exit_task(struct task_struct *child) */ spin_lock(&child_ctx->lock); child->perf_counter_ctxp = NULL; - if (child_ctx->parent_ctx) { - /* - * This context is a clone; unclone it so it can't get - * swapped to another process while we're removing all - * the counters from it. - */ - put_ctx(child_ctx->parent_ctx); - child_ctx->parent_ctx = NULL; - } + /* + * If this context is a clone; unclone it so it can't get + * swapped to another process while we're removing all + * the counters from it. + */ + unclone_ctx(child_ctx); spin_unlock(&child_ctx->lock); local_irq_restore(flags); -- GitLab From 812e7a6a43fc34bc8f70c2b80db4ea5997d66ea8 Mon Sep 17 00:00:00 2001 From: Wengang Wang Date: Fri, 10 Jul 2009 13:26:04 +0800 Subject: [PATCH 0017/1342] ocfs2: log the actual return value of ocfs2_file_aio_write() in ocfs2_file_aio_write(), log_exit() could don't log the value which is really returned. this patch fixes it. Signed-off-by: Wengang Wang Signed-off-by: Joel Becker --- fs/ocfs2/file.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/fs/ocfs2/file.c b/fs/ocfs2/file.c index 62442e413a0..a49fa44aea1 100644 --- a/fs/ocfs2/file.c +++ b/fs/ocfs2/file.c @@ -1918,8 +1918,10 @@ out_sems: mutex_unlock(&inode->i_mutex); + if (written) + ret = written; mlog_exit(ret); - return written ? written : ret; + return ret; } static int ocfs2_splice_to_file(struct pipe_inode_info *pipe, -- GitLab From 52d422de22b26d96bbdfbc605eb31c2994df6d0b Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Fri, 10 Jul 2009 22:47:28 -0300 Subject: [PATCH 0018/1342] perf report: Adjust column width to the values sampled Auto-adjust column width of perf report output to the longest occuring string length. Example: [acme@doppio pahole]$ perf report --sort comm,dso,symbol | head -13 12.79% pahole /usr/lib64/libdw-0.141.so [.] __libdw_find_attr 8.90% pahole /lib64/libc-2.10.1.so [.] _int_malloc 8.68% pahole /usr/lib64/libdw-0.141.so [.] __libdw_form_val_len 8.15% pahole /lib64/libc-2.10.1.so [.] __GI_strcmp 6.80% pahole /lib64/libc-2.10.1.so [.] __tsearch 5.54% pahole ./build/libdwarves.so.1.0.0 [.] tag__recode_dwarf_type [acme@doppio pahole]$ [acme@doppio pahole]$ perf report --sort comm,dso,symbol -d /lib64/libc-2.10.1.so | head -10 21.92% pahole /lib64/libc-2.10.1.so [.] _int_malloc 20.08% pahole /lib64/libc-2.10.1.so [.] __GI_strcmp 16.75% pahole /lib64/libc-2.10.1.so [.] __tsearch [acme@doppio pahole]$ Also add these extra options to control the new behaviour: -w, --field-width Force each column width to the provided list, for large terminal readability. -t, --field-separator: Use a special separator character and don't pad with spaces, replacing all occurances of this separator in symbol names (and other output) with a '.' character, that thus it's the only non valid separator. Signed-off-by: Arnaldo Carvalho de Melo Cc: Frederic Weisbecker Cc: Mike Galbraith Cc: Peter Zijlstra Cc: Paul Mackerras LKML-Reference: <20090711014728.GH3452@ghostprotocols.net> Signed-off-by: Ingo Molnar --- tools/perf/Documentation/perf-report.txt | 12 ++ tools/perf/builtin-report.c | 174 ++++++++++++++++++----- tools/perf/util/include/linux/kernel.h | 8 ++ tools/perf/util/symbol.c | 1 + tools/perf/util/symbol.h | 1 + 5 files changed, 164 insertions(+), 32 deletions(-) diff --git a/tools/perf/Documentation/perf-report.txt b/tools/perf/Documentation/perf-report.txt index 8aa3f8c8870..05774dfbd14 100644 --- a/tools/perf/Documentation/perf-report.txt +++ b/tools/perf/Documentation/perf-report.txt @@ -33,6 +33,18 @@ OPTIONS Only consider these symbols. CSV that understands file://filename entries. +-w:: +--field-width=:: + Force each column width to the provided list, for large terminal + readability. + +-t:: +--field-separator=:: + + Use a special separator character and don't pad with spaces, replacing + all occurances of this separator in symbol names (and other output) + with a '.' character, that thus it's the only non valid separator. + SEE ALSO -------- linkperf:perf-stat[1] diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c index 4e5cc266311..740da43f313 100644 --- a/tools/perf/builtin-report.c +++ b/tools/perf/builtin-report.c @@ -33,8 +33,10 @@ static char *vmlinux = NULL; static char default_sort_order[] = "comm,dso"; static char *sort_order = default_sort_order; -static char *dso_list_str, *comm_list_str, *sym_list_str; +static char *dso_list_str, *comm_list_str, *sym_list_str, + *col_width_list_str; static struct strlist *dso_list, *comm_list, *sym_list; +static char *field_sep; static int input; static int show_mask = SHOW_KERNEL | SHOW_USER | SHOW_HV; @@ -129,6 +131,33 @@ typedef union event_union { struct read_event read; } event_t; +static int repsep_fprintf(FILE *fp, const char *fmt, ...) +{ + int n; + va_list ap; + + va_start(ap, fmt); + if (!field_sep) + n = vfprintf(fp, fmt, ap); + else { + char *bf = NULL; + n = vasprintf(&bf, fmt, ap); + if (n > 0) { + char *sep = bf; + while (1) { + sep = strchr(sep, *field_sep); + if (sep == NULL) + break; + *sep = '.'; + } + } + fputs(bf, fp); + free(bf); + } + va_end(ap); + return n; +} + static LIST_HEAD(dsos); static struct dso *kernel_dso; static struct dso *vdso; @@ -360,12 +389,28 @@ static struct thread *thread__new(pid_t pid) return self; } +static unsigned int dsos__col_width, + comms__col_width, + threads__col_width; + static int thread__set_comm(struct thread *self, const char *comm) { if (self->comm) free(self->comm); self->comm = strdup(comm); - return self->comm ? 0 : -ENOMEM; + if (!self->comm) + return -ENOMEM; + + if (!col_width_list_str && !field_sep && + (!comm_list || strlist__has_entry(comm_list, comm))) { + unsigned int slen = strlen(comm); + if (slen > comms__col_width) { + comms__col_width = slen; + threads__col_width = slen + 6; + } + } + + return 0; } static size_t thread__fprintf(struct thread *self, FILE *fp) @@ -536,7 +581,8 @@ struct sort_entry { int64_t (*cmp)(struct hist_entry *, struct hist_entry *); int64_t (*collapse)(struct hist_entry *, struct hist_entry *); - size_t (*print)(FILE *fp, struct hist_entry *); + size_t (*print)(FILE *fp, struct hist_entry *, unsigned int width); + unsigned int *width; }; static int64_t cmp_null(void *l, void *r) @@ -558,15 +604,17 @@ sort__thread_cmp(struct hist_entry *left, struct hist_entry *right) } static size_t -sort__thread_print(FILE *fp, struct hist_entry *self) +sort__thread_print(FILE *fp, struct hist_entry *self, unsigned int width) { - return fprintf(fp, "%16s:%5d", self->thread->comm ?: "", self->thread->pid); + return repsep_fprintf(fp, "%*s:%5d", width - 6, + self->thread->comm ?: "", self->thread->pid); } static struct sort_entry sort_thread = { - .header = " Command: Pid", + .header = "Command: Pid", .cmp = sort__thread_cmp, .print = sort__thread_print, + .width = &threads__col_width, }; /* --sort comm */ @@ -590,16 +638,17 @@ sort__comm_collapse(struct hist_entry *left, struct hist_entry *right) } static size_t -sort__comm_print(FILE *fp, struct hist_entry *self) +sort__comm_print(FILE *fp, struct hist_entry *self, unsigned int width) { - return fprintf(fp, "%16s", self->thread->comm); + return repsep_fprintf(fp, "%*s", width, self->thread->comm); } static struct sort_entry sort_comm = { - .header = " Command", + .header = "Command", .cmp = sort__comm_cmp, .collapse = sort__comm_collapse, .print = sort__comm_print, + .width = &comms__col_width, }; /* --sort dso */ @@ -617,18 +666,19 @@ sort__dso_cmp(struct hist_entry *left, struct hist_entry *right) } static size_t -sort__dso_print(FILE *fp, struct hist_entry *self) +sort__dso_print(FILE *fp, struct hist_entry *self, unsigned int width) { if (self->dso) - return fprintf(fp, "%-25s", self->dso->name); + return repsep_fprintf(fp, "%-*s", width, self->dso->name); - return fprintf(fp, "%016llx ", (u64)self->ip); + return repsep_fprintf(fp, "%*llx", width, (u64)self->ip); } static struct sort_entry sort_dso = { - .header = "Shared Object ", + .header = "Shared Object", .cmp = sort__dso_cmp, .print = sort__dso_print, + .width = &dsos__col_width, }; /* --sort symbol */ @@ -648,22 +698,23 @@ sort__sym_cmp(struct hist_entry *left, struct hist_entry *right) } static size_t -sort__sym_print(FILE *fp, struct hist_entry *self) +sort__sym_print(FILE *fp, struct hist_entry *self, unsigned int width __used) { size_t ret = 0; if (verbose) - ret += fprintf(fp, "%#018llx ", (u64)self->ip); + ret += repsep_fprintf(fp, "%#018llx ", (u64)self->ip); if (self->sym) { - ret += fprintf(fp, "[%c] %s", + ret += repsep_fprintf(fp, "[%c] %s", self->dso == kernel_dso ? 'k' : self->dso == hypervisor_dso ? 'h' : '.', self->sym->name); if (self->sym->module) - ret += fprintf(fp, "\t[%s]", self->sym->module->name); + ret += repsep_fprintf(fp, "\t[%s]", + self->sym->module->name); } else { - ret += fprintf(fp, "%#016llx", (u64)self->ip); + ret += repsep_fprintf(fp, "%#016llx", (u64)self->ip); } return ret; @@ -690,19 +741,19 @@ sort__parent_cmp(struct hist_entry *left, struct hist_entry *right) } static size_t -sort__parent_print(FILE *fp, struct hist_entry *self) +sort__parent_print(FILE *fp, struct hist_entry *self, unsigned int width) { - size_t ret = 0; - - ret += fprintf(fp, "%-20s", self->parent ? self->parent->name : "[other]"); - - return ret; + return repsep_fprintf(fp, "%-*s", width, + self->parent ? self->parent->name : "[other]"); } +static unsigned int parent_symbol__col_width; + static struct sort_entry sort_parent = { - .header = "Parent symbol ", + .header = "Parent symbol", .cmp = sort__parent_cmp, .print = sort__parent_print, + .width = &parent_symbol__col_width, }; static int sort__need_collapse = 0; @@ -967,17 +1018,18 @@ hist_entry__fprintf(FILE *fp, struct hist_entry *self, u64 total_samples) return 0; if (total_samples) - ret = percent_color_fprintf(fp, " %6.2f%%", - (self->count * 100.0) / total_samples); + ret = percent_color_fprintf(fp, + field_sep ? "%.2f" : " %6.2f%%", + (self->count * 100.0) / total_samples); else - ret = fprintf(fp, "%12Ld ", self->count); + ret = fprintf(fp, field_sep ? "%lld" : "%12lld ", self->count); list_for_each_entry(se, &hist_entry__sort_list, list) { if (exclude_other && (se == &sort_parent)) continue; - fprintf(fp, " "); - ret += se->print(fp, self); + fprintf(fp, "%s", field_sep ?: " "); + ret += se->print(fp, self, se->width ? *se->width : 0); } ret += fprintf(fp, "\n"); @@ -992,6 +1044,18 @@ hist_entry__fprintf(FILE *fp, struct hist_entry *self, u64 total_samples) * */ +static void dso__calc_col_width(struct dso *self) +{ + if (!col_width_list_str && !field_sep && + (!dso_list || strlist__has_entry(dso_list, self->name))) { + unsigned int slen = strlen(self->name); + if (slen > dsos__col_width) + dsos__col_width = slen; + } + + self->slen_calculated = 1; +} + static struct symbol * resolve_symbol(struct thread *thread, struct map **mapp, struct dso **dsop, u64 *ipp) @@ -1011,6 +1075,14 @@ resolve_symbol(struct thread *thread, struct map **mapp, map = thread__find_map(thread, ip); if (map != NULL) { + /* + * We have to do this here as we may have a dso + * with no symbol hit that has a name longer than + * the ones with symbols sampled. + */ + if (!map->dso->slen_calculated) + dso__calc_col_width(map->dso); + if (mapp) *mapp = map; got_map: @@ -1282,6 +1354,8 @@ static size_t output__fprintf(FILE *fp, u64 total_samples) struct sort_entry *se; struct rb_node *nd; size_t ret = 0; + unsigned int width; + char *col_width = col_width_list_str; fprintf(fp, "\n"); fprintf(fp, "#\n"); @@ -1292,10 +1366,29 @@ static size_t output__fprintf(FILE *fp, u64 total_samples) list_for_each_entry(se, &hist_entry__sort_list, list) { if (exclude_other && (se == &sort_parent)) continue; - fprintf(fp, " %s", se->header); + if (field_sep) { + fprintf(fp, "%c%s", *field_sep, se->header); + continue; + } + width = strlen(se->header); + if (se->width) { + if (col_width_list_str) { + if (col_width) { + *se->width = atoi(col_width); + col_width = strchr(col_width, ','); + if (col_width) + ++col_width; + } + } + width = *se->width = max(*se->width, width); + } + fprintf(fp, " %*s", width, se->header); } fprintf(fp, "\n"); + if (field_sep) + goto print_entries; + fprintf(fp, "# ........"); list_for_each_entry(se, &hist_entry__sort_list, list) { unsigned int i; @@ -1304,13 +1397,18 @@ static size_t output__fprintf(FILE *fp, u64 total_samples) continue; fprintf(fp, " "); - for (i = 0; i < strlen(se->header); i++) + if (se->width) + width = *se->width; + else + width = strlen(se->header); + for (i = 0; i < width; i++) fprintf(fp, "."); } fprintf(fp, "\n"); fprintf(fp, "#\n"); +print_entries: for (nd = rb_first(&output_hists); nd; nd = rb_next(nd)) { pos = rb_entry(nd, struct hist_entry, rb_node); ret += hist_entry__fprintf(fp, pos, total_samples); @@ -1900,6 +1998,12 @@ static const struct option options[] = { "only consider symbols in these comms"), OPT_STRING('S', "symbols", &sym_list_str, "symbol[,symbol...]", "only consider these symbols"), + OPT_STRING('w', "column-widths", &col_width_list_str, + "width[,width...]", + "don't try to adjust column width, use these fixed values"), + OPT_STRING('t', "field-separator", &field_sep, "separator", + "separator for columns, no spaces will be added between " + "columns '.' is reserved."), OPT_END() }; @@ -1956,6 +2060,12 @@ int cmd_report(int argc, const char **argv, const char *prefix __used) setup_list(&comm_list, comm_list_str, "comm"); setup_list(&sym_list, sym_list_str, "symbol"); + if (field_sep && *field_sep == '.') { + fputs("'.' is the only non valid --field-separator argument\n", + stderr); + exit(129); + } + setup_pager(); return __cmd_report(); diff --git a/tools/perf/util/include/linux/kernel.h b/tools/perf/util/include/linux/kernel.h index 99c1b3d1edd..a6b87390cb5 100644 --- a/tools/perf/util/include/linux/kernel.h +++ b/tools/perf/util/include/linux/kernel.h @@ -18,4 +18,12 @@ (type *)((char *)__mptr - offsetof(type, member)); }) #endif +#ifndef max +#define max(x, y) ({ \ + typeof(x) _max1 = (x); \ + typeof(y) _max2 = (y); \ + (void) (&_max1 == &_max2); \ + _max1 > _max2 ? _max1 : _max2; }) +#endif + #endif diff --git a/tools/perf/util/symbol.c b/tools/perf/util/symbol.c index 4683b67b5ee..8efe7e41109 100644 --- a/tools/perf/util/symbol.c +++ b/tools/perf/util/symbol.c @@ -65,6 +65,7 @@ struct dso *dso__new(const char *name, unsigned int sym_priv_size) self->syms = RB_ROOT; self->sym_priv_size = sym_priv_size; self->find_symbol = dso__find_symbol; + self->slen_calculated = 0; } return self; diff --git a/tools/perf/util/symbol.h b/tools/perf/util/symbol.h index 7918cffb23c..2f92b21c712 100644 --- a/tools/perf/util/symbol.h +++ b/tools/perf/util/symbol.h @@ -25,6 +25,7 @@ struct dso { struct symbol *(*find_symbol)(struct dso *, u64 ip); unsigned int sym_priv_size; unsigned char adjust_symbols; + unsigned char slen_calculated; char name[0]; }; -- GitLab From 60c1baf1248e00d423604f018c8af1cf750ad885 Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Sat, 11 Jul 2009 12:18:33 -0300 Subject: [PATCH 0019/1342] perf report: Tidy up reporting of symbols not found Always printing the level info about if it is in the kernel, hypervisor or userspace as that is in the hist_entry. Signed-off-by: Arnaldo Carvalho de Melo LKML-Reference: <1247325517-12272-1-git-send-email-acme@redhat.com> Signed-off-by: Ingo Molnar --- tools/perf/builtin-report.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c index 740da43f313..617f4cb7f16 100644 --- a/tools/perf/builtin-report.c +++ b/tools/perf/builtin-report.c @@ -705,10 +705,9 @@ sort__sym_print(FILE *fp, struct hist_entry *self, unsigned int width __used) if (verbose) ret += repsep_fprintf(fp, "%#018llx ", (u64)self->ip); + ret += repsep_fprintf(fp, "[%c] ", self->level); if (self->sym) { - ret += repsep_fprintf(fp, "[%c] %s", - self->dso == kernel_dso ? 'k' : - self->dso == hypervisor_dso ? 'h' : '.', self->sym->name); + ret += repsep_fprintf(fp, "%s", self->sym->name); if (self->sym->module) ret += repsep_fprintf(fp, "\t[%s]", -- GitLab From 27d0fd410c3cee00ece2e55f4354a7a9ec1a6a6a Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Sat, 11 Jul 2009 12:18:34 -0300 Subject: [PATCH 0020/1342] strlist: Introduce strlist__entry and strlist__nr_entries methods The strlist__entry method allows accessing strlists like an array, will be used in the 'perf report' to access the first entry. We now keep the nr_entries so that we can check if we have just one entry, will be used in 'perf report' to improve the output by showing just at the top when we have just, say, one DSO. While at it use nr_entries to optimize strlist__is_empty by not using the far more costly rb_first based implementation. Signed-off-by: Arnaldo Carvalho de Melo LKML-Reference: <1247325517-12272-2-git-send-email-acme@redhat.com> Signed-off-by: Ingo Molnar --- tools/perf/util/strlist.c | 20 ++++++++++++++++++-- tools/perf/util/strlist.h | 11 +++++++++-- 2 files changed, 27 insertions(+), 4 deletions(-) diff --git a/tools/perf/util/strlist.c b/tools/perf/util/strlist.c index 025a78edfff..7ad38171dc2 100644 --- a/tools/perf/util/strlist.c +++ b/tools/perf/util/strlist.c @@ -64,6 +64,7 @@ int strlist__add(struct strlist *self, const char *new_entry) rb_link_node(&sn->rb_node, parent, p); rb_insert_color(&sn->rb_node, &self->entries); + ++self->nr_entries; return 0; } @@ -155,8 +156,9 @@ struct strlist *strlist__new(bool dupstr, const char *slist) struct strlist *self = malloc(sizeof(*self)); if (self != NULL) { - self->entries = RB_ROOT; - self->dupstr = dupstr; + self->entries = RB_ROOT; + self->dupstr = dupstr; + self->nr_entries = 0; if (slist && strlist__parse_list(self, slist) != 0) goto out_error; } @@ -182,3 +184,17 @@ void strlist__delete(struct strlist *self) free(self); } } + +struct str_node *strlist__entry(const struct strlist *self, unsigned int idx) +{ + struct rb_node *nd; + + for (nd = rb_first(&self->entries); nd; nd = rb_next(nd)) { + struct str_node *pos = rb_entry(nd, struct str_node, rb_node); + + if (!idx--) + return pos; + } + + return NULL; +} diff --git a/tools/perf/util/strlist.h b/tools/perf/util/strlist.h index 2fdcfee8758..921818e44a5 100644 --- a/tools/perf/util/strlist.h +++ b/tools/perf/util/strlist.h @@ -11,7 +11,8 @@ struct str_node { struct strlist { struct rb_root entries; - bool dupstr; + unsigned int nr_entries; + bool dupstr; }; struct strlist *strlist__new(bool dupstr, const char *slist); @@ -21,11 +22,17 @@ void strlist__remove(struct strlist *self, struct str_node *sn); int strlist__load(struct strlist *self, const char *filename); int strlist__add(struct strlist *self, const char *str); +struct str_node *strlist__entry(const struct strlist *self, unsigned int idx); bool strlist__has_entry(struct strlist *self, const char *entry); static inline bool strlist__empty(const struct strlist *self) { - return rb_first(&self->entries) == NULL; + return self->nr_entries == 0; +} + +static inline unsigned int strlist__nr_entries(const struct strlist *self) +{ + return self->nr_entries; } int strlist__parse_list(struct strlist *self, const char *s); -- GitLab From 021191b35cdfb1b5ee6e78ed5ae010114a40902c Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Sat, 11 Jul 2009 12:18:35 -0300 Subject: [PATCH 0021/1342] perf report: Make the output more compact When we filter by column content we may end up with a column that has the same value for all the lines. So remove that column and tell its unique value on the top, as a comment. Example: [acme@doppio pahole]$ perf report --sort comm,dso,symbol -d ./build/libdwarves.so.1.0.0 -C pahole | head -15 # dso: ./build/libdwarves.so.1.0.0 # comm: pahole # Samples: 58409 # # Overhead Symbol # ........ ...... # 20.93% [.] tag__recode_dwarf_type 14.94% [.] namespace__recode_dwarf_types 10.38% [.] cu__table_add_tag 6.69% [.] __die__process_tag 5.05% [.] die__process_function 4.70% [.] list__for_all_tags 3.68% [.] tag__init 3.48% [.] die__create_new_parameter [acme@doppio pahole]$ Signed-off-by: Arnaldo Carvalho de Melo LKML-Reference: <1247325517-12272-3-git-send-email-acme@redhat.com> Signed-off-by: Ingo Molnar --- tools/perf/builtin-report.c | 36 +++++++++++++++++++++--------------- 1 file changed, 21 insertions(+), 15 deletions(-) diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c index 617f4cb7f16..f3422121d85 100644 --- a/tools/perf/builtin-report.c +++ b/tools/perf/builtin-report.c @@ -583,6 +583,7 @@ struct sort_entry { int64_t (*collapse)(struct hist_entry *, struct hist_entry *); size_t (*print)(FILE *fp, struct hist_entry *, unsigned int width); unsigned int *width; + bool elide; }; static int64_t cmp_null(void *l, void *r) @@ -1024,7 +1025,7 @@ hist_entry__fprintf(FILE *fp, struct hist_entry *self, u64 total_samples) ret = fprintf(fp, field_sep ? "%lld" : "%12lld ", self->count); list_for_each_entry(se, &hist_entry__sort_list, list) { - if (exclude_other && (se == &sort_parent)) + if (se->elide) continue; fprintf(fp, "%s", field_sep ?: " "); @@ -1079,7 +1080,7 @@ resolve_symbol(struct thread *thread, struct map **mapp, * with no symbol hit that has a name longer than * the ones with symbols sampled. */ - if (!map->dso->slen_calculated) + if (!sort_dso.elide && !map->dso->slen_calculated) dso__calc_col_width(map->dso); if (mapp) @@ -1356,14 +1357,12 @@ static size_t output__fprintf(FILE *fp, u64 total_samples) unsigned int width; char *col_width = col_width_list_str; - fprintf(fp, "\n"); - fprintf(fp, "#\n"); - fprintf(fp, "# (%Ld samples)\n", (u64)total_samples); + fprintf(fp, "# Samples: %Ld\n", (u64)total_samples); fprintf(fp, "#\n"); fprintf(fp, "# Overhead"); list_for_each_entry(se, &hist_entry__sort_list, list) { - if (exclude_other && (se == &sort_parent)) + if (se->elide) continue; if (field_sep) { fprintf(fp, "%c%s", *field_sep, se->header); @@ -1392,7 +1391,7 @@ static size_t output__fprintf(FILE *fp, u64 total_samples) list_for_each_entry(se, &hist_entry__sort_list, list) { unsigned int i; - if (exclude_other && (se == &sort_parent)) + if (se->elide) continue; fprintf(fp, " "); @@ -2022,7 +2021,8 @@ static void setup_sorting(void) } static void setup_list(struct strlist **list, const char *list_str, - const char *list_name) + struct sort_entry *se, const char *list_name, + FILE *fp) { if (list_str) { *list = strlist__new(true, list_str); @@ -2031,6 +2031,11 @@ static void setup_list(struct strlist **list, const char *list_str, list_name); exit(129); } + if (strlist__nr_entries(*list) == 1) { + fprintf(fp, "# %s: %s\n", list_name, + strlist__entry(*list, 0)->s); + se->elide = true; + } } } @@ -2044,9 +2049,10 @@ int cmd_report(int argc, const char **argv, const char *prefix __used) setup_sorting(); - if (parent_pattern != default_parent_pattern) + if (parent_pattern != default_parent_pattern) { sort_dimension__add("parent"); - else + sort_parent.elide = 1; + } else exclude_other = 0; /* @@ -2055,9 +2061,11 @@ int cmd_report(int argc, const char **argv, const char *prefix __used) if (argc) usage_with_options(report_usage, options); - setup_list(&dso_list, dso_list_str, "dso"); - setup_list(&comm_list, comm_list_str, "comm"); - setup_list(&sym_list, sym_list_str, "symbol"); + setup_pager(); + + setup_list(&dso_list, dso_list_str, &sort_dso, "dso", stdout); + setup_list(&comm_list, comm_list_str, &sort_comm, "comm", stdout); + setup_list(&sym_list, sym_list_str, &sort_sym, "symbol", stdout); if (field_sep && *field_sep == '.') { fputs("'.' is the only non valid --field-separator argument\n", @@ -2065,7 +2073,5 @@ int cmd_report(int argc, const char **argv, const char *prefix __used) exit(129); } - setup_pager(); - return __cmd_report(); } -- GitLab From a25e46c46311316cd1b3f27f8bb036df1693c032 Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Sat, 11 Jul 2009 12:18:36 -0300 Subject: [PATCH 0022/1342] perf_counter tools: PLT info is stripped in -debuginfo packages So we need to get the richer .symtab from the debuginfo packages but the PLT info from the original DSO where we have just the leaner .dynsym symtab. Example: | [acme@doppio pahole]$ perf report --sort comm,dso,symbol > before | [acme@doppio pahole]$ perf report --sort comm,dso,symbol > after | [acme@doppio pahole]$ diff -U1 before after | --- before 2009-07-11 11:04:22.688595741 -0300 | +++ after 2009-07-11 11:04:33.380595676 -0300 | @@ -80,3 +80,2 @@ | 0.07% pahole ./build/pahole [.] pahole_stealer | - 0.06% pahole /usr/lib64/libdw-0.141.so [.] 0x00000000007140 | 0.06% pahole /usr/lib64/libdw-0.141.so [.] __libdw_getabbrev | @@ -91,2 +90,3 @@ | 0.06% pahole [kernel] [k] free_hot_cold_page | + 0.06% pahole /usr/lib64/libdw-0.141.so [.] tfind@plt | 0.05% pahole ./build/libdwarves.so.1.0.0 [.] ftype__add_parameter | @@ -242,2 +242,3 @@ | 0.01% pahole [kernel] [k] account_group_user_time | + 0.01% pahole /usr/lib64/libdw-0.141.so [.] strlen@plt | 0.01% pahole ./build/pahole [.] strcmp@plt | [acme@doppio pahole]$ Signed-off-by: Arnaldo Carvalho de Melo LKML-Reference: <1247325517-12272-4-git-send-email-acme@redhat.com> Signed-off-by: Ingo Molnar --- tools/perf/util/symbol.c | 116 ++++++++++++++++++++++----------------- 1 file changed, 65 insertions(+), 51 deletions(-) diff --git a/tools/perf/util/symbol.c b/tools/perf/util/symbol.c index 8efe7e41109..f40266b4845 100644 --- a/tools/perf/util/symbol.c +++ b/tools/perf/util/symbol.c @@ -374,36 +374,61 @@ static Elf_Scn *elf_section_by_name(Elf *elf, GElf_Ehdr *ep, idx < nr_entries; \ ++idx, pos = gelf_getrela(reldata, idx, &pos_mem)) -static int dso__synthesize_plt_symbols(struct dso *self, Elf *elf, - GElf_Ehdr *ehdr, Elf_Scn *scn_dynsym, - GElf_Shdr *shdr_dynsym, - size_t dynsym_idx, int verbose) +/* + * We need to check if we have a .dynsym, so that we can handle the + * .plt, synthesizing its symbols, that aren't on the symtabs (be it + * .dynsym or .symtab). + * And always look at the original dso, not at debuginfo packages, that + * have the PLT data stripped out (shdr_rel_plt.sh_type == SHT_NOBITS). + */ +static int dso__synthesize_plt_symbols(struct dso *self, int verbose) { uint32_t nr_rel_entries, idx; GElf_Sym sym; u64 plt_offset; GElf_Shdr shdr_plt; struct symbol *f; - GElf_Shdr shdr_rel_plt; + GElf_Shdr shdr_rel_plt, shdr_dynsym; Elf_Data *reldata, *syms, *symstrs; - Elf_Scn *scn_plt_rel, *scn_symstrs; + Elf_Scn *scn_plt_rel, *scn_symstrs, *scn_dynsym; + size_t dynsym_idx; + GElf_Ehdr ehdr; char sympltname[1024]; - int nr = 0, symidx; + Elf *elf; + int nr = 0, symidx, fd, err = 0; + + fd = open(self->name, O_RDONLY); + if (fd < 0) + goto out; + + elf = elf_begin(fd, ELF_C_READ_MMAP, NULL); + if (elf == NULL) + goto out_close; + + if (gelf_getehdr(elf, &ehdr) == NULL) + goto out_elf_end; + + scn_dynsym = elf_section_by_name(elf, &ehdr, &shdr_dynsym, + ".dynsym", &dynsym_idx); + if (scn_dynsym == NULL) + goto out_elf_end; - scn_plt_rel = elf_section_by_name(elf, ehdr, &shdr_rel_plt, + scn_plt_rel = elf_section_by_name(elf, &ehdr, &shdr_rel_plt, ".rela.plt", NULL); if (scn_plt_rel == NULL) { - scn_plt_rel = elf_section_by_name(elf, ehdr, &shdr_rel_plt, + scn_plt_rel = elf_section_by_name(elf, &ehdr, &shdr_rel_plt, ".rel.plt", NULL); if (scn_plt_rel == NULL) - return 0; + goto out_elf_end; } + err = -1; + if (shdr_rel_plt.sh_link != dynsym_idx) - return 0; + goto out_elf_end; - if (elf_section_by_name(elf, ehdr, &shdr_plt, ".plt", NULL) == NULL) - return 0; + if (elf_section_by_name(elf, &ehdr, &shdr_plt, ".plt", NULL) == NULL) + goto out_elf_end; /* * Fetch the relocation section to find the indexes to the GOT @@ -411,19 +436,19 @@ static int dso__synthesize_plt_symbols(struct dso *self, Elf *elf, */ reldata = elf_getdata(scn_plt_rel, NULL); if (reldata == NULL) - return -1; + goto out_elf_end; syms = elf_getdata(scn_dynsym, NULL); if (syms == NULL) - return -1; + goto out_elf_end; - scn_symstrs = elf_getscn(elf, shdr_dynsym->sh_link); + scn_symstrs = elf_getscn(elf, shdr_dynsym.sh_link); if (scn_symstrs == NULL) - return -1; + goto out_elf_end; symstrs = elf_getdata(scn_symstrs, NULL); if (symstrs == NULL) - return -1; + goto out_elf_end; nr_rel_entries = shdr_rel_plt.sh_size / shdr_rel_plt.sh_entsize; plt_offset = shdr_plt.sh_offset; @@ -442,7 +467,7 @@ static int dso__synthesize_plt_symbols(struct dso *self, Elf *elf, f = symbol__new(plt_offset, shdr_plt.sh_entsize, sympltname, self->sym_priv_size, 0, verbose); if (!f) - return -1; + goto out_elf_end; dso__insert_symbol(self, f); ++nr; @@ -460,19 +485,25 @@ static int dso__synthesize_plt_symbols(struct dso *self, Elf *elf, f = symbol__new(plt_offset, shdr_plt.sh_entsize, sympltname, self->sym_priv_size, 0, verbose); if (!f) - return -1; + goto out_elf_end; dso__insert_symbol(self, f); ++nr; } - } else { - /* - * TODO: There are still one more shdr_rel_plt.sh_type - * I have to investigate, but probably should be ignored. - */ } - return nr; + err = 0; +out_elf_end: + elf_end(elf); +out_close: + close(fd); + + if (err == 0) + return nr; +out: + fprintf(stderr, "%s: problems reading %s PLT info.\n", + __func__, self->name); + return 0; } static int dso__load_sym(struct dso *self, int fd, const char *name, @@ -486,9 +517,8 @@ static int dso__load_sym(struct dso *self, int fd, const char *name, GElf_Shdr shdr; Elf_Data *syms; GElf_Sym sym; - Elf_Scn *sec, *sec_dynsym, *sec_strndx; + Elf_Scn *sec, *sec_strndx; Elf *elf; - size_t dynsym_idx; int nr = 0; elf = elf_begin(fd, ELF_C_READ_MMAP, NULL); @@ -505,32 +535,11 @@ static int dso__load_sym(struct dso *self, int fd, const char *name, goto out_elf_end; } - /* - * We need to check if we have a .dynsym, so that we can handle the - * .plt, synthesizing its symbols, that aren't on the symtabs (be it - * .dynsym or .symtab) - */ - sec_dynsym = elf_section_by_name(elf, &ehdr, &shdr, - ".dynsym", &dynsym_idx); - if (sec_dynsym != NULL) { - nr = dso__synthesize_plt_symbols(self, elf, &ehdr, - sec_dynsym, &shdr, - dynsym_idx, verbose); - if (nr < 0) - goto out_elf_end; - } - - /* - * But if we have a full .symtab (that is a superset of .dynsym) we - * should add the symbols not in the .dynsyn - */ sec = elf_section_by_name(elf, &ehdr, &shdr, ".symtab", NULL); if (sec == NULL) { - if (sec_dynsym == NULL) + sec = elf_section_by_name(elf, &ehdr, &shdr, ".dynsym", NULL); + if (sec == NULL) goto out_elf_end; - - sec = sec_dynsym; - gelf_getshdr(sec, &shdr); } syms = elf_getdata(sec, NULL); @@ -669,6 +678,11 @@ more: if (!ret) goto more; + if (ret > 0) { + int nr_plt = dso__synthesize_plt_symbols(self, verbose); + if (nr_plt > 0) + ret += nr_plt; + } out: free(name); return ret; -- GitLab From e3d7e183dc276df2fcaf02af173a49ad119ba9f9 Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Sat, 11 Jul 2009 12:18:37 -0300 Subject: [PATCH 0023/1342] perf report: Introduce -n/--show-nr-samples [acme@doppio pahole]$ perf report -ns comm,dso,symbol -d /lib64/libc-2.10.1.so -C pahole | head -17 21.94% 32101 [.] _int_malloc 20.10% 29402 [.] __GI_strcmp 16.77% 24533 [.] __tsearch 12.61% 18450 [.] malloc_consolidate 6.42% 9394 [.] _int_free 6.28% 9191 [.] __tfind 4.56% 6678 [.] __GI___libc_free 4.46% 6520 [.] _IO_vfprintf_internal 2.59% 3786 [.] __malloc 1.17% 1716 [.] __GI_memcpy [acme@doppio pahole]$ Signed-off-by: Arnaldo Carvalho de Melo LKML-Reference: <1247325517-12272-5-git-send-email-acme@redhat.com> Signed-off-by: Ingo Molnar --- tools/perf/Documentation/perf-report.txt | 3 +++ tools/perf/builtin-report.c | 18 ++++++++++++++++++ 2 files changed, 21 insertions(+) diff --git a/tools/perf/Documentation/perf-report.txt b/tools/perf/Documentation/perf-report.txt index 05774dfbd14..e72e9311078 100644 --- a/tools/perf/Documentation/perf-report.txt +++ b/tools/perf/Documentation/perf-report.txt @@ -24,6 +24,9 @@ OPTIONS --dsos=:: Only consider symbols in these dsos. CSV that understands file://filename entries. +-n +--show-nr-samples + Show the number of samples for each symbol -C:: --comms=:: Only consider symbols in these comms. CSV that understands diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c index f3422121d85..430a195b858 100644 --- a/tools/perf/builtin-report.c +++ b/tools/perf/builtin-report.c @@ -51,6 +51,7 @@ static int verbose; static int modules; static int full_paths; +static int show_nr_samples; static unsigned long page_size; static unsigned long mmap_window = 32; @@ -1024,6 +1025,13 @@ hist_entry__fprintf(FILE *fp, struct hist_entry *self, u64 total_samples) else ret = fprintf(fp, field_sep ? "%lld" : "%12lld ", self->count); + if (show_nr_samples) { + if (field_sep) + fprintf(fp, "%c%lld", *field_sep, self->count); + else + fprintf(fp, "%11lld", self->count); + } + list_for_each_entry(se, &hist_entry__sort_list, list) { if (se->elide) continue; @@ -1361,6 +1369,12 @@ static size_t output__fprintf(FILE *fp, u64 total_samples) fprintf(fp, "#\n"); fprintf(fp, "# Overhead"); + if (show_nr_samples) { + if (field_sep) + fprintf(fp, "%cSamples", *field_sep); + else + fputs(" Samples ", fp); + } list_for_each_entry(se, &hist_entry__sort_list, list) { if (se->elide) continue; @@ -1388,6 +1402,8 @@ static size_t output__fprintf(FILE *fp, u64 total_samples) goto print_entries; fprintf(fp, "# ........"); + if (show_nr_samples) + fprintf(fp, " .........."); list_for_each_entry(se, &hist_entry__sort_list, list) { unsigned int i; @@ -1979,6 +1995,8 @@ static const struct option options[] = { OPT_STRING('k', "vmlinux", &vmlinux, "file", "vmlinux pathname"), OPT_BOOLEAN('m', "modules", &modules, "load module symbols - WARNING: use only with -k and LIVE kernel"), + OPT_BOOLEAN('n', "show-nr-samples", &show_nr_samples, + "Show a column with the number of samples"), OPT_STRING('s', "sort", &sort_order, "key[,key2...]", "sort by key(s): pid, comm, dso, symbol, parent"), OPT_BOOLEAN('P', "full-paths", &full_paths, -- GitLab From e705cee427e319665969ef7ac664f3612dec8899 Mon Sep 17 00:00:00 2001 From: Giuseppe Mazzotta Date: Sun, 12 Jul 2009 21:02:27 -0700 Subject: [PATCH 0024/1342] Input: wistron_btns - recognize Maxdata Pro 7000 notebooks This patch adds DMI information to automatically load the correct layout for the Maxdata Pro 7000X/DX notebook models. Such notebooks are clones of Fujitsu Amilo V2000, the hook for the v2000 is being used and I have tested that perfectly works. The immediate result of integrating this patch is that the five special buttons will work on these specific notebook models and that the RF killswitch will not be activated after suspend. This patch definitively obsoletes the fsam7400 module which I was still needing to enable wifi and to fix the RF killswitch suspend problem; in the current 2.6.30 kernel it is necessary to load the wistron_btns module with options 'force=1 keymap=1557/MS2141', which was not anyway a complete workaround. Signed-off-by: Giuseppe Mazzotta Signed-off-by: Dmitry Torokhov --- drivers/input/misc/wistron_btns.c | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/drivers/input/misc/wistron_btns.c b/drivers/input/misc/wistron_btns.c index 7c8957dd22c..26e17a9a22e 100644 --- a/drivers/input/misc/wistron_btns.c +++ b/drivers/input/misc/wistron_btns.c @@ -644,6 +644,15 @@ static struct dmi_system_id dmi_ids[] __initdata = { }, .driver_data = keymap_fs_amilo_pro_v2000 }, + { + .callback = dmi_matched, + .ident = "Maxdata Pro 7000 DX", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "MAXDATA"), + DMI_MATCH(DMI_PRODUCT_NAME, "Pro 7000"), + }, + .driver_data = keymap_fs_amilo_pro_v2000 + }, { .callback = dmi_matched, .ident = "Fujitsu N3510", -- GitLab From 70a6f2e6d6b8653d394b63210ec57b4c78f3dcd8 Mon Sep 17 00:00:00 2001 From: Michael Gruber Date: Sun, 12 Jul 2009 20:51:36 -0700 Subject: [PATCH 0025/1342] Input: xpad - don't resend successfully sent outgoing requests This avoids an infinite loop. Signed-off-by: Michael Gruber Signed-off-by: Dmitry Torokhov --- drivers/input/joystick/xpad.c | 26 +++++++++++++------------- 1 file changed, 13 insertions(+), 13 deletions(-) diff --git a/drivers/input/joystick/xpad.c b/drivers/input/joystick/xpad.c index b868b8d5fbb..f155ad8cdae 100644 --- a/drivers/input/joystick/xpad.c +++ b/drivers/input/joystick/xpad.c @@ -470,20 +470,20 @@ static void xpad_irq_out(struct urb *urb) status = urb->status; switch (status) { - case 0: + case 0: /* success */ - break; - case -ECONNRESET: - case -ENOENT: - case -ESHUTDOWN: - /* this urb is terminated, clean up */ - dbg("%s - urb shutting down with status: %d", - __func__, status); - return; - default: - dbg("%s - nonzero urb status received: %d", - __func__, status); - goto exit; + return; + + case -ECONNRESET: + case -ENOENT: + case -ESHUTDOWN: + /* this urb is terminated, clean up */ + dbg("%s - urb shutting down with status: %d", __func__, status); + return; + + default: + dbg("%s - nonzero urb status received: %d", __func__, status); + goto exit; } exit: -- GitLab From 35db715bfd3805b04aa233b9933b9facfa9a3290 Mon Sep 17 00:00:00 2001 From: Frans Pop Date: Sun, 12 Jul 2009 20:51:32 -0700 Subject: [PATCH 0026/1342] Input: pcspkr - switch driver to dev_pm_ops Gets rid of the following warning: Platform driver 'pcspkr' needs updating - please use dev_pm_ops Signed-off-by: Frans Pop Signed-off-by: Dmitry Torokhov --- drivers/input/misc/pcspkr.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) diff --git a/drivers/input/misc/pcspkr.c b/drivers/input/misc/pcspkr.c index d6a30cee7bc..663bbc7ae2f 100644 --- a/drivers/input/misc/pcspkr.c +++ b/drivers/input/misc/pcspkr.c @@ -113,7 +113,7 @@ static int __devexit pcspkr_remove(struct platform_device *dev) return 0; } -static int pcspkr_suspend(struct platform_device *dev, pm_message_t state) +static int pcspkr_suspend(struct device *dev) { pcspkr_event(NULL, EV_SND, SND_BELL, 0); @@ -126,14 +126,18 @@ static void pcspkr_shutdown(struct platform_device *dev) pcspkr_event(NULL, EV_SND, SND_BELL, 0); } +static struct dev_pm_ops pcspkr_pm_ops = { + .suspend = pcspkr_suspend, +}; + static struct platform_driver pcspkr_platform_driver = { .driver = { .name = "pcspkr", .owner = THIS_MODULE, + .pm = &pcspkr_pm_ops, }, .probe = pcspkr_probe, .remove = __devexit_p(pcspkr_remove), - .suspend = pcspkr_suspend, .shutdown = pcspkr_shutdown, }; -- GitLab From f0a14de2f82dd6aa13e04816da2091c7ed0f77cf Mon Sep 17 00:00:00 2001 From: Simon Davie Date: Sun, 12 Jul 2009 20:44:09 -0700 Subject: [PATCH 0027/1342] Input: atkbd - add forced release keys quirk for FSC Amilo Pi 3525 This patch enables forced releasing of the Fn+Volume hotkeys on the Fujitsu Siemens Amilo Pi 3525 notebook. Signed-off-by: Simon Davie Signed-off-by: Dmitry Torokhov --- drivers/input/keyboard/atkbd.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/drivers/input/keyboard/atkbd.c b/drivers/input/keyboard/atkbd.c index df3f8aa6811..809a7ddbe3a 100644 --- a/drivers/input/keyboard/atkbd.c +++ b/drivers/input/keyboard/atkbd.c @@ -894,6 +894,13 @@ static unsigned int atkbd_amilo_pa1510_forced_release_keys[] = { 0xb0, 0xae, -1U }; +/* + * Amilo Pi 3525 key release for Fn+Volume keys not working + */ +static unsigned int atkbd_amilo_pi3525_forced_release_keys[] = { + 0x20, 0xa0, 0x2e, 0xae, 0x30, 0xb0, -1U +}; + /* * Amilo Xi 3650 key release for light touch bar not working */ @@ -1567,6 +1574,15 @@ static struct dmi_system_id atkbd_dmi_quirk_table[] __initdata = { .callback = atkbd_setup_forced_release, .driver_data = atkbd_amilo_pa1510_forced_release_keys, }, + { + .ident = "Fujitsu Amilo Pi 3525", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU SIEMENS"), + DMI_MATCH(DMI_PRODUCT_NAME, "AMILO Pi 3525"), + }, + .callback = atkbd_setup_forced_release, + .driver_data = atkbd_amilo_pi3525_forced_release_keys, + }, { .ident = "Fujitsu Amilo Xi 3650", .matches = { -- GitLab From f1c6a58121f9846ac665b0fbd3cbab90ce8bcbac Mon Sep 17 00:00:00 2001 From: Daniel Qarras Date: Sun, 12 Jul 2009 04:32:40 -0700 Subject: [PATCH 0028/1342] perf_counter, x86: Extend perf_counter Pentium M support I've attached a patch to remove the Pentium M special casing of EMON and as noticed at least with my Pentium M the hardware PMU now works: Performance counter stats for '/bin/ls /var/tmp': 1.809988 task-clock-msecs # 0.125 CPUs 1 context-switches # 0.001 M/sec 0 CPU-migrations # 0.000 M/sec 224 page-faults # 0.124 M/sec 1425648 cycles # 787.656 M/sec 912755 instructions # 0.640 IPC Vince suggested that this code was trying to address erratum Y17 in Pentium-M's: http://download.intel.com/support/processors/mobile/pm/sb/25266532.pdf But that erratum (related to IA32_MISC_ENABLES.7) does not affect perfcounters as we dont use this toggle to disable RDPMC and WRMSR/RDMSR access to performance counters. We keep cr4's bit 8 (X86_CR4_PCE) clear so unprivileged RDPMC access is not allowed anyway. Cc: Vince Weaver Cc: Peter Zijlstra Cc: Stephane Eranian LKML-Reference: Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/perf_counter.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) diff --git a/arch/x86/kernel/cpu/perf_counter.c b/arch/x86/kernel/cpu/perf_counter.c index bed1c4c2f25..7e346d4bc0f 100644 --- a/arch/x86/kernel/cpu/perf_counter.c +++ b/arch/x86/kernel/cpu/perf_counter.c @@ -1583,10 +1583,8 @@ static int p6_pmu_init(void) break; case 9: case 13: - /* for Pentium M, we need to check if PMU exist */ - rdmsr(MSR_IA32_MISC_ENABLE, low, high); - if (low & MSR_IA32_MISC_ENABLE_EMON) - break; + /* Pentium M */ + break; default: pr_cont("unsupported p6 CPU model %d ", boot_cpu_data.x86_model); -- GitLab From d4d7d0b9545721d3cabb19d15163bbc66b797707 Mon Sep 17 00:00:00 2001 From: Chris Wilson Date: Mon, 6 Jul 2009 09:31:33 +0100 Subject: [PATCH 0029/1342] perf_counter: Fix the tracepoint channel to perfcounters Fix a missed rename in EVENT_PROFILE support so that it gets built and allows tracepoint tracing from the 'perf' tool. Fix a typo in the (never before built & enabled) portion in perf_counter.c as well, and update that code to the attr.config changes as well. Signed-off-by: Chris Wilson Cc: Ben Gamari Cc: Jason Baron Cc: Frederic Weisbecker Cc: Mike Galbraith Cc: Peter Zijlstra Cc: Paul Mackerras Cc: Steven Rostedt LKML-Reference: <1246869094-21237-1-git-send-email-chris@chris-wilson.co.uk> Signed-off-by: Ingo Molnar --- init/Kconfig | 2 +- kernel/perf_counter.c | 10 +++------- 2 files changed, 4 insertions(+), 8 deletions(-) diff --git a/init/Kconfig b/init/Kconfig index 1ce05a4cb5f..cb2c0927022 100644 --- a/init/Kconfig +++ b/init/Kconfig @@ -962,7 +962,7 @@ config PERF_COUNTERS config EVENT_PROFILE bool "Tracepoint profile sources" - depends on PERF_COUNTERS && EVENT_TRACER + depends on PERF_COUNTERS && EVENT_TRACING default y endmenu diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index d55a50da234..c6c38fb7766 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -3671,7 +3671,7 @@ static const struct pmu perf_ops_task_clock = { void perf_tpcounter_event(int event_id) { struct perf_sample_data data = { - .regs = get_irq_regs(); + .regs = get_irq_regs(), .addr = 0, }; @@ -3687,16 +3687,12 @@ extern void ftrace_profile_disable(int); static void tp_perf_counter_destroy(struct perf_counter *counter) { - ftrace_profile_disable(perf_event_id(&counter->attr)); + ftrace_profile_disable(counter->attr.config); } static const struct pmu *tp_perf_counter_init(struct perf_counter *counter) { - int event_id = perf_event_id(&counter->attr); - int ret; - - ret = ftrace_profile_enable(event_id); - if (ret) + if (ftrace_profile_enable(counter->attr.config)) return NULL; counter->destroy = tp_perf_counter_destroy; -- GitLab From 23cdb5d5171d591ec911aada682e09d53c14a810 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Mon, 13 Jul 2009 02:25:47 +0200 Subject: [PATCH 0030/1342] perf_counter tools: Fix index boundary check Keep index within event_type_descriptors[] Signed-off-by: Roel Kluin Cc: Andrew Morton Cc: Peter Zijlstra Cc: Mike Galbraith Cc: Paul Mackerras Cc: Arnaldo Carvalho de Melo Cc: Frederic Weisbecker LKML-Reference: <4A5A7F0B.4070106@gmail.com> Signed-off-by: Ingo Molnar --- tools/perf/util/parse-events.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/tools/perf/util/parse-events.c b/tools/perf/util/parse-events.c index 518a33affe1..d18c98edd00 100644 --- a/tools/perf/util/parse-events.c +++ b/tools/perf/util/parse-events.c @@ -436,7 +436,7 @@ void print_events(void) for (i = 0; i < ARRAY_SIZE(event_symbols); i++, syms++) { type = syms->type + 1; - if (type > ARRAY_SIZE(event_type_descriptors)) + if (type >= ARRAY_SIZE(event_type_descriptors)) type = 0; if (type != prev_type) -- GitLab From 832cc28d5bc676331e6376d940ae45d5937aa688 Mon Sep 17 00:00:00 2001 From: Florian Mickler Date: Mon, 13 Jul 2009 18:40:32 +0800 Subject: [PATCH 0031/1342] drm/i915: Set lvds dual channel according to register from vbios Vbios will set lvds register correctly based on current algorithm for lingle/dual Channel LVDS when system boot, so we can accept this configuration directly, regardless of LVDS enable status. It fixed freedesktop.org bug #22262 Signed-off-by: Florian Mickler Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_display.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 508838ee31e..3371cb0ba81 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -645,7 +645,7 @@ intel_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc, int err = target; if (IS_I9XX(dev) && intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS) && - (I915_READ(LVDS) & LVDS_PORT_EN) != 0) { + (I915_READ(LVDS)) != 0) { /* * For LVDS, if the panel is on, just rely on its current * settings for dual-channel. We haven't figured out how to -- GitLab From 8a90523639f49dc4b4fa7ae47bb9c8ed73ea8577 Mon Sep 17 00:00:00 2001 From: Jesse Barnes Date: Sat, 11 Jul 2009 16:48:03 -0400 Subject: [PATCH 0032/1342] drm/i915: refactor error detection & collection This patch refactors the existing error detection and collection code, placing most of it in i915_handle_error(). Additionally, we introduce a work queue for scheduling post-crash tasks such as generating a uevent. Using the uevent facility, userspace should be able to capture a post-mortem dump for diagnostics. Signed-off-by: Jesse Barnes Signed-off-by: Ben Gamari Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/i915_drv.h | 1 + drivers/gpu/drm/i915/i915_gem_debugfs.c | 2 + drivers/gpu/drm/i915/i915_irq.c | 232 ++++++++++++++++-------- 3 files changed, 161 insertions(+), 74 deletions(-) diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h index d0875287588..b05b44dd3bf 100644 --- a/drivers/gpu/drm/i915/i915_drv.h +++ b/drivers/gpu/drm/i915/i915_drv.h @@ -229,6 +229,7 @@ typedef struct drm_i915_private { spinlock_t error_lock; struct drm_i915_error_state *first_error; + struct work_struct error_work; /* Register state */ u8 saveLBB; diff --git a/drivers/gpu/drm/i915/i915_gem_debugfs.c b/drivers/gpu/drm/i915/i915_gem_debugfs.c index 9a44bfcb813..cb3b97405fb 100644 --- a/drivers/gpu/drm/i915/i915_gem_debugfs.c +++ b/drivers/gpu/drm/i915/i915_gem_debugfs.c @@ -343,6 +343,8 @@ static int i915_error_state(struct seq_file *m, void *unused) error = dev_priv->first_error; + seq_printf(m, "Time: %ld s %ld us\n", error->time.tv_sec, + error->time.tv_usec); seq_printf(m, "EIR: 0x%08x\n", error->eir); seq_printf(m, " PGTBL_ER: 0x%08x\n", error->pgtbl_er); seq_printf(m, " INSTPM: 0x%08x\n", error->instpm); diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c index 7ba23a69a0c..f340b3fd54e 100644 --- a/drivers/gpu/drm/i915/i915_irq.c +++ b/drivers/gpu/drm/i915/i915_irq.c @@ -290,6 +290,35 @@ irqreturn_t igdng_irq_handler(struct drm_device *dev) return ret; } +/** + * i915_error_work_func - do process context error handling work + * @work: work struct + * + * Fire an error uevent so userspace can see that a hang or error + * was detected. + */ +static void i915_error_work_func(struct work_struct *work) +{ + drm_i915_private_t *dev_priv = container_of(work, drm_i915_private_t, + error_work); + struct drm_device *dev = dev_priv->dev; + char *event_string = "ERROR=1"; + char *envp[] = { event_string, NULL }; + + DRM_DEBUG("generating error event\n"); + + kobject_uevent_env(&dev->primary->kdev.kobj, KOBJ_CHANGE, envp); +} + +/** + * i915_capture_error_state - capture an error record for later analysis + * @dev: drm device + * + * Should be called when an error is detected (either a hang or an error + * interrupt) to capture error state from the time of the error. Fills + * out a structure which becomes available in debugfs for user level tools + * to pick up. + */ static void i915_capture_error_state(struct drm_device *dev) { struct drm_i915_private *dev_priv = dev->dev_private; @@ -325,12 +354,137 @@ static void i915_capture_error_state(struct drm_device *dev) error->acthd = I915_READ(ACTHD_I965); } + do_gettimeofday(&error->time); + dev_priv->first_error = error; out: spin_unlock_irqrestore(&dev_priv->error_lock, flags); } +/** + * i915_handle_error - handle an error interrupt + * @dev: drm device + * + * Do some basic checking of regsiter state at error interrupt time and + * dump it to the syslog. Also call i915_capture_error_state() to make + * sure we get a record and make it available in debugfs. Fire a uevent + * so userspace knows something bad happened (should trigger collection + * of a ring dump etc.). + */ +static void i915_handle_error(struct drm_device *dev) +{ + struct drm_i915_private *dev_priv = dev->dev_private; + u32 eir = I915_READ(EIR); + u32 pipea_stats = I915_READ(PIPEASTAT); + u32 pipeb_stats = I915_READ(PIPEBSTAT); + + i915_capture_error_state(dev); + + printk(KERN_ERR "render error detected, EIR: 0x%08x\n", + eir); + + if (IS_G4X(dev)) { + if (eir & (GM45_ERROR_MEM_PRIV | GM45_ERROR_CP_PRIV)) { + u32 ipeir = I915_READ(IPEIR_I965); + + printk(KERN_ERR " IPEIR: 0x%08x\n", + I915_READ(IPEIR_I965)); + printk(KERN_ERR " IPEHR: 0x%08x\n", + I915_READ(IPEHR_I965)); + printk(KERN_ERR " INSTDONE: 0x%08x\n", + I915_READ(INSTDONE_I965)); + printk(KERN_ERR " INSTPS: 0x%08x\n", + I915_READ(INSTPS)); + printk(KERN_ERR " INSTDONE1: 0x%08x\n", + I915_READ(INSTDONE1)); + printk(KERN_ERR " ACTHD: 0x%08x\n", + I915_READ(ACTHD_I965)); + I915_WRITE(IPEIR_I965, ipeir); + (void)I915_READ(IPEIR_I965); + } + if (eir & GM45_ERROR_PAGE_TABLE) { + u32 pgtbl_err = I915_READ(PGTBL_ER); + printk(KERN_ERR "page table error\n"); + printk(KERN_ERR " PGTBL_ER: 0x%08x\n", + pgtbl_err); + I915_WRITE(PGTBL_ER, pgtbl_err); + (void)I915_READ(PGTBL_ER); + } + } + + if (IS_I9XX(dev)) { + if (eir & I915_ERROR_PAGE_TABLE) { + u32 pgtbl_err = I915_READ(PGTBL_ER); + printk(KERN_ERR "page table error\n"); + printk(KERN_ERR " PGTBL_ER: 0x%08x\n", + pgtbl_err); + I915_WRITE(PGTBL_ER, pgtbl_err); + (void)I915_READ(PGTBL_ER); + } + } + + if (eir & I915_ERROR_MEMORY_REFRESH) { + printk(KERN_ERR "memory refresh error\n"); + printk(KERN_ERR "PIPEASTAT: 0x%08x\n", + pipea_stats); + printk(KERN_ERR "PIPEBSTAT: 0x%08x\n", + pipeb_stats); + /* pipestat has already been acked */ + } + if (eir & I915_ERROR_INSTRUCTION) { + printk(KERN_ERR "instruction error\n"); + printk(KERN_ERR " INSTPM: 0x%08x\n", + I915_READ(INSTPM)); + if (!IS_I965G(dev)) { + u32 ipeir = I915_READ(IPEIR); + + printk(KERN_ERR " IPEIR: 0x%08x\n", + I915_READ(IPEIR)); + printk(KERN_ERR " IPEHR: 0x%08x\n", + I915_READ(IPEHR)); + printk(KERN_ERR " INSTDONE: 0x%08x\n", + I915_READ(INSTDONE)); + printk(KERN_ERR " ACTHD: 0x%08x\n", + I915_READ(ACTHD)); + I915_WRITE(IPEIR, ipeir); + (void)I915_READ(IPEIR); + } else { + u32 ipeir = I915_READ(IPEIR_I965); + + printk(KERN_ERR " IPEIR: 0x%08x\n", + I915_READ(IPEIR_I965)); + printk(KERN_ERR " IPEHR: 0x%08x\n", + I915_READ(IPEHR_I965)); + printk(KERN_ERR " INSTDONE: 0x%08x\n", + I915_READ(INSTDONE_I965)); + printk(KERN_ERR " INSTPS: 0x%08x\n", + I915_READ(INSTPS)); + printk(KERN_ERR " INSTDONE1: 0x%08x\n", + I915_READ(INSTDONE1)); + printk(KERN_ERR " ACTHD: 0x%08x\n", + I915_READ(ACTHD_I965)); + I915_WRITE(IPEIR_I965, ipeir); + (void)I915_READ(IPEIR_I965); + } + } + + I915_WRITE(EIR, eir); + (void)I915_READ(EIR); + eir = I915_READ(EIR); + if (eir) { + /* + * some errors might have become stuck, + * mask them. + */ + DRM_ERROR("EIR stuck: 0x%08x, masking\n", eir); + I915_WRITE(EMR, I915_READ(EMR) | eir); + I915_WRITE(IIR, I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT); + } + + schedule_work(&dev_priv->error_work); +} + irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS) { struct drm_device *dev = (struct drm_device *) arg; @@ -372,6 +526,9 @@ irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS) pipea_stats = I915_READ(PIPEASTAT); pipeb_stats = I915_READ(PIPEBSTAT); + if (iir & I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT) + i915_handle_error(dev); + /* * Clear the PIPE(A|B)STAT regs before the IIR */ @@ -409,80 +566,6 @@ irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS) I915_READ(PORT_HOTPLUG_STAT); } - if (iir & I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT) { - u32 eir = I915_READ(EIR); - - i915_capture_error_state(dev); - - printk(KERN_ERR "render error detected, EIR: 0x%08x\n", - eir); - if (eir & I915_ERROR_PAGE_TABLE) { - u32 pgtbl_err = I915_READ(PGTBL_ER); - printk(KERN_ERR "page table error\n"); - printk(KERN_ERR " PGTBL_ER: 0x%08x\n", - pgtbl_err); - I915_WRITE(PGTBL_ER, pgtbl_err); - (void)I915_READ(PGTBL_ER); - } - if (eir & I915_ERROR_MEMORY_REFRESH) { - printk(KERN_ERR "memory refresh error\n"); - printk(KERN_ERR "PIPEASTAT: 0x%08x\n", - pipea_stats); - printk(KERN_ERR "PIPEBSTAT: 0x%08x\n", - pipeb_stats); - /* pipestat has already been acked */ - } - if (eir & I915_ERROR_INSTRUCTION) { - printk(KERN_ERR "instruction error\n"); - printk(KERN_ERR " INSTPM: 0x%08x\n", - I915_READ(INSTPM)); - if (!IS_I965G(dev)) { - u32 ipeir = I915_READ(IPEIR); - - printk(KERN_ERR " IPEIR: 0x%08x\n", - I915_READ(IPEIR)); - printk(KERN_ERR " IPEHR: 0x%08x\n", - I915_READ(IPEHR)); - printk(KERN_ERR " INSTDONE: 0x%08x\n", - I915_READ(INSTDONE)); - printk(KERN_ERR " ACTHD: 0x%08x\n", - I915_READ(ACTHD)); - I915_WRITE(IPEIR, ipeir); - (void)I915_READ(IPEIR); - } else { - u32 ipeir = I915_READ(IPEIR_I965); - - printk(KERN_ERR " IPEIR: 0x%08x\n", - I915_READ(IPEIR_I965)); - printk(KERN_ERR " IPEHR: 0x%08x\n", - I915_READ(IPEHR_I965)); - printk(KERN_ERR " INSTDONE: 0x%08x\n", - I915_READ(INSTDONE_I965)); - printk(KERN_ERR " INSTPS: 0x%08x\n", - I915_READ(INSTPS)); - printk(KERN_ERR " INSTDONE1: 0x%08x\n", - I915_READ(INSTDONE1)); - printk(KERN_ERR " ACTHD: 0x%08x\n", - I915_READ(ACTHD_I965)); - I915_WRITE(IPEIR_I965, ipeir); - (void)I915_READ(IPEIR_I965); - } - } - - I915_WRITE(EIR, eir); - (void)I915_READ(EIR); - eir = I915_READ(EIR); - if (eir) { - /* - * some errors might have become stuck, - * mask them. - */ - DRM_ERROR("EIR stuck: 0x%08x, masking\n", eir); - I915_WRITE(EMR, I915_READ(EMR) | eir); - I915_WRITE(IIR, I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT); - } - } - I915_WRITE(IIR, iir); new_iir = I915_READ(IIR); /* Flush posted writes */ @@ -830,6 +913,7 @@ void i915_driver_irq_preinstall(struct drm_device * dev) atomic_set(&dev_priv->irq_received, 0); INIT_WORK(&dev_priv->hotplug_work, i915_hotplug_work_func); + INIT_WORK(&dev_priv->error_work, i915_error_work_func); if (IS_IGDNG(dev)) { igdng_irq_preinstall(dev); -- GitLab From 5e4d6fa72619aeea271d2ad704757717b06e291a Mon Sep 17 00:00:00 2001 From: Keith Packard Date: Sun, 12 Jul 2009 23:53:17 -0700 Subject: [PATCH 0033/1342] drm/i915: Allow frame buffers up to 4096x4096 on 915/945 class hardware The 915 and 945 scanout engines can handle frame buffers up to 4096 pixels wide. Pre-9xx hardware has an 8192 byte stride limit, and so we leave the existing 2048 max in place. I'm not sure why we limit the height to the same value; there's no intrinsic hardware limit in the scanout engine. Signed-off-by: Keith Packard Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_display.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 3371cb0ba81..984645e26a2 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -3148,6 +3148,9 @@ void intel_modeset_init(struct drm_device *dev) if (IS_I965G(dev)) { dev->mode_config.max_width = 8192; dev->mode_config.max_height = 8192; + } else if (IS_I9XX(dev)) { + dev->mode_config.max_width = 4096; + dev->mode_config.max_height = 4096; } else { dev->mode_config.max_width = 2048; dev->mode_config.max_height = 2048; -- GitLab From ed8c754b292f02d0550596481527b7bf2b52d024 Mon Sep 17 00:00:00 2001 From: Tormod Volden Date: Mon, 13 Jul 2009 22:26:48 +0200 Subject: [PATCH 0034/1342] drm/i915: ignore lvds on AOpen Mini PC MP-915 This motherboard thinks it has an LVDS connected, so without this patch the screen goes blank on the connected VGA monitor. More information (for the non-KMS case) in fd.o bug #18004. Signed-off-by: Tormod Volden Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_lvds.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/drivers/gpu/drm/i915/intel_lvds.c b/drivers/gpu/drm/i915/intel_lvds.c index 9ab38efffec..43c7d9aa59c 100644 --- a/drivers/gpu/drm/i915/intel_lvds.c +++ b/drivers/gpu/drm/i915/intel_lvds.c @@ -778,6 +778,14 @@ static const struct dmi_system_id intel_no_lvds[] = { DMI_MATCH(DMI_PRODUCT_NAME, "i965GMx-IF"), }, }, + { + .callback = intel_no_lvds_dmi_callback, + .ident = "AOpen Mini PC MP915", + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, "AOpen"), + DMI_MATCH(DMI_BOARD_NAME, "i915GMx-F"), + }, + }, { .callback = intel_no_lvds_dmi_callback, .ident = "Aopen i945GTt-VFA", -- GitLab From 4fed598a49c014cbc563179b25f2a4b8565e2a50 Mon Sep 17 00:00:00 2001 From: Ryusuke Konishi Date: Sun, 12 Jul 2009 11:13:55 +0900 Subject: [PATCH 0035/1342] fs/Kconfig: move nilfs2 out fs/Kconfig file was split into individual fs/*/Kconfig files before nilfs was merged. I've found the current config entry of nilfs is tainting the work. Sorry, I didn't notice. This fixes the violation. Signed-off-by: Ryusuke Konishi Cc: Alexey Dobriyan --- fs/Kconfig | 27 +-------------------------- fs/nilfs2/Kconfig | 25 +++++++++++++++++++++++++ 2 files changed, 26 insertions(+), 26 deletions(-) create mode 100644 fs/nilfs2/Kconfig diff --git a/fs/Kconfig b/fs/Kconfig index a97263be6a9..0e7da7bb5d9 100644 --- a/fs/Kconfig +++ b/fs/Kconfig @@ -186,32 +186,7 @@ source "fs/romfs/Kconfig" source "fs/sysv/Kconfig" source "fs/ufs/Kconfig" source "fs/exofs/Kconfig" - -config NILFS2_FS - tristate "NILFS2 file system support (EXPERIMENTAL)" - depends on BLOCK && EXPERIMENTAL - select CRC32 - help - NILFS2 is a log-structured file system (LFS) supporting continuous - snapshotting. In addition to versioning capability of the entire - file system, users can even restore files mistakenly overwritten or - destroyed just a few seconds ago. Since this file system can keep - consistency like conventional LFS, it achieves quick recovery after - system crashes. - - NILFS2 creates a number of checkpoints every few seconds or per - synchronous write basis (unless there is no change). Users can - select significant versions among continuously created checkpoints, - and can change them into snapshots which will be preserved for long - periods until they are changed back to checkpoints. Each - snapshot is mountable as a read-only file system concurrently with - its writable mount, and this feature is convenient for online backup. - - Some features including atime, extended attributes, and POSIX ACLs, - are not supported yet. - - To compile this file system support as a module, choose M here: the - module will be called nilfs2. If unsure, say N. +source "fs/nilfs2/Kconfig" endif # MISC_FILESYSTEMS diff --git a/fs/nilfs2/Kconfig b/fs/nilfs2/Kconfig new file mode 100644 index 00000000000..72da095d400 --- /dev/null +++ b/fs/nilfs2/Kconfig @@ -0,0 +1,25 @@ +config NILFS2_FS + tristate "NILFS2 file system support (EXPERIMENTAL)" + depends on BLOCK && EXPERIMENTAL + select CRC32 + help + NILFS2 is a log-structured file system (LFS) supporting continuous + snapshotting. In addition to versioning capability of the entire + file system, users can even restore files mistakenly overwritten or + destroyed just a few seconds ago. Since this file system can keep + consistency like conventional LFS, it achieves quick recovery after + system crashes. + + NILFS2 creates a number of checkpoints every few seconds or per + synchronous write basis (unless there is no change). Users can + select significant versions among continuously created checkpoints, + and can change them into snapshots which will be preserved for long + periods until they are changed back to checkpoints. Each + snapshot is mountable as a read-only file system concurrently with + its writable mount, and this feature is convenient for online backup. + + Some features including atime, extended attributes, and POSIX ACLs, + are not supported yet. + + To compile this file system support as a module, choose M here: the + module will be called nilfs2. If unsure, say N. -- GitLab From f936601471d1454dacbd3b2a961fd4d883090aeb Mon Sep 17 00:00:00 2001 From: Daniel Mack Date: Mon, 13 Jul 2009 22:22:49 -0700 Subject: [PATCH 0036/1342] Input: fix EVIOCGNAME/JSIOCGNAME regression Commit 3d5cb60e ("Input: simplify name handling for certain input handles") introduced a regression for the EVIOCGNAME/JSIOCGNAME ioctl. Before this, patch, the platform device's name was given back to userspace which was good to identify devices. After this patch, the device is ("event%d", minor) which is not descriptive at all. This fixes the behaviour by taking dev->name. Reported-by: Sven Neumann Signed-off-by: Daniel Mack Reviewed-by: Thadeu Lima de Souza Cascardo Signed-off-by: Dmitry Torokhov --- drivers/input/evdev.c | 3 +-- drivers/input/joydev.c | 2 +- 2 files changed, 2 insertions(+), 3 deletions(-) diff --git a/drivers/input/evdev.c b/drivers/input/evdev.c index 114efd8dc8f..1148140d08a 100644 --- a/drivers/input/evdev.c +++ b/drivers/input/evdev.c @@ -608,8 +608,7 @@ static long evdev_do_ioctl(struct file *file, unsigned int cmd, p, compat_mode); if (_IOC_NR(cmd) == _IOC_NR(EVIOCGNAME(0))) - return str_to_user(dev_name(&evdev->dev), - _IOC_SIZE(cmd), p); + return str_to_user(dev->name, _IOC_SIZE(cmd), p); if (_IOC_NR(cmd) == _IOC_NR(EVIOCGPHYS(0))) return str_to_user(dev->phys, _IOC_SIZE(cmd), p); diff --git a/drivers/input/joydev.c b/drivers/input/joydev.c index 0e12f89276a..4cfd084fa89 100644 --- a/drivers/input/joydev.c +++ b/drivers/input/joydev.c @@ -536,7 +536,7 @@ static int joydev_ioctl_common(struct joydev *joydev, default: if ((cmd & ~IOCSIZE_MASK) == JSIOCGNAME(0)) { int len; - const char *name = dev_name(&dev->dev); + const char *name = dev->name; if (!name) return 0; -- GitLab From dff33cfcefa31c30b72c57f44586754ea9e8f3e2 Mon Sep 17 00:00:00 2001 From: Jesse Barnes Date: Tue, 14 Jul 2009 10:15:56 -0700 Subject: [PATCH 0037/1342] drm/i915: FIFO watermark calculation fixes I discovered several bugs in the FIFO code that was recently applied. Some of them fell into the "how did this ever work" category, since in some cases we were using the wrong FIFO size values, and the calculations ended up being way off. This patch fixes all the bugs I found, and works well on my GM45, 915GM and 855GM test machines; but as usual with these sorts of patches broader testing is definitely requested (in particular this patch affects 830, 845 and 865 for which I don't have test hardware). Overall, the patch clarifies the watermark calculation function by adding some comments and debug info, and making the variable names a bit clearer. The "get FIFO size" portion of the code has also been corrected, so we should be able to properly detect the FIFO allocations for each pipe, for use in the watermark calculation. Signed-off-by: Jesse Barnes Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/i915_reg.h | 2 +- drivers/gpu/drm/i915/intel_display.c | 186 ++++++++++++++++----------- 2 files changed, 113 insertions(+), 75 deletions(-) diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h index 6c085848409..897a116cad1 100644 --- a/drivers/gpu/drm/i915/i915_reg.h +++ b/drivers/gpu/drm/i915/i915_reg.h @@ -1618,7 +1618,7 @@ #define I830_FIFO_LINE_SIZE 32 #define I945_FIFO_SIZE 127 /* 945 & 965 */ #define I915_FIFO_SIZE 95 -#define I855GM_FIFO_SIZE 255 +#define I855GM_FIFO_SIZE 127 /* In cachelines */ #define I830_FIFO_SIZE 95 #define I915_MAX_WM 0x3f diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 984645e26a2..3fa0d63c83b 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -1623,44 +1623,67 @@ static struct intel_watermark_params igd_cursor_hplloff_wm = { IGD_FIFO_LINE_SIZE }; static struct intel_watermark_params i945_wm_info = { - I915_FIFO_LINE_SIZE, + I945_FIFO_SIZE, I915_MAX_WM, 1, - 0, - IGD_FIFO_LINE_SIZE + 2, + I915_FIFO_LINE_SIZE }; static struct intel_watermark_params i915_wm_info = { - I945_FIFO_SIZE, + I915_FIFO_SIZE, I915_MAX_WM, 1, - 0, + 2, I915_FIFO_LINE_SIZE }; static struct intel_watermark_params i855_wm_info = { I855GM_FIFO_SIZE, I915_MAX_WM, 1, - 0, + 2, I830_FIFO_LINE_SIZE }; static struct intel_watermark_params i830_wm_info = { I830_FIFO_SIZE, I915_MAX_WM, 1, - 0, + 2, I830_FIFO_LINE_SIZE }; +/** + * intel_calculate_wm - calculate watermark level + * @clock_in_khz: pixel clock + * @wm: chip FIFO params + * @pixel_size: display pixel size + * @latency_ns: memory latency for the platform + * + * Calculate the watermark level (the level at which the display plane will + * start fetching from memory again). Each chip has a different display + * FIFO size and allocation, so the caller needs to figure that out and pass + * in the correct intel_watermark_params structure. + * + * As the pixel clock runs, the FIFO will be drained at a rate that depends + * on the pixel size. When it reaches the watermark level, it'll start + * fetching FIFO line sized based chunks from memory until the FIFO fills + * past the watermark point. If the FIFO drains completely, a FIFO underrun + * will occur, and a display engine hang could result. + */ static unsigned long intel_calculate_wm(unsigned long clock_in_khz, struct intel_watermark_params *wm, int pixel_size, unsigned long latency_ns) { - unsigned long bytes_required, wm_size; + unsigned long entries_required, wm_size; + + entries_required = (clock_in_khz * pixel_size * latency_ns) / 1000000; + entries_required /= wm->cacheline_size; + + DRM_DEBUG("FIFO entries required for mode: %d\n", entries_required); - bytes_required = (clock_in_khz * pixel_size * latency_ns) / 1000000; - bytes_required /= wm->cacheline_size; - wm_size = wm->fifo_size - bytes_required - wm->guard_size; + wm_size = wm->fifo_size - (entries_required + wm->guard_size); + + DRM_DEBUG("FIFO watermark level: %d\n", wm_size); if (wm_size > wm->max_wm) wm_size = wm->max_wm; @@ -1799,8 +1822,37 @@ static void igd_enable_cxsr(struct drm_device *dev, unsigned long clock, return; } -const static int latency_ns = 5000; /* default for non-igd platforms */ +const static int latency_ns = 3000; /* default for non-igd platforms */ + +static int intel_get_fifo_size(struct drm_device *dev, int plane) +{ + struct drm_i915_private *dev_priv = dev->dev_private; + uint32_t dsparb = I915_READ(DSPARB); + int size; + + if (IS_I9XX(dev)) { + if (plane == 0) + size = dsparb & 0x7f; + else + size = ((dsparb >> DSPARB_CSTART_SHIFT) & 0x7f) - + (dsparb & 0x7f); + } else if (IS_I85X(dev)) { + if (plane == 0) + size = dsparb & 0x1ff; + else + size = ((dsparb >> DSPARB_BEND_SHIFT) & 0x1ff) - + (dsparb & 0x1ff); + size >>= 1; /* Convert to cachelines */ + } else { + size = dsparb & 0x7f; + size >>= 1; /* Convert to cachelines */ + } + + DRM_DEBUG("FIFO size - (0x%08x) %s: %d\n", dsparb, plane ? "B" : "A", + size); + return size; +} static void i965_update_wm(struct drm_device *dev) { @@ -1817,101 +1869,87 @@ static void i9xx_update_wm(struct drm_device *dev, int planea_clock, int planeb_clock, int sr_hdisplay, int pixel_size) { struct drm_i915_private *dev_priv = dev->dev_private; - uint32_t fwater_lo = I915_READ(FW_BLC) & MM_FIFO_WATERMARK; - uint32_t fwater_hi = I915_READ(FW_BLC2) & LM_FIFO_WATERMARK; - int bsize, asize, cwm, bwm = 1, awm = 1, srwm = 1; - uint32_t dsparb = I915_READ(DSPARB); - int planea_entries, planeb_entries; - struct intel_watermark_params *wm_params; + uint32_t fwater_lo; + uint32_t fwater_hi; + int total_size, cacheline_size, cwm, srwm = 1; + int planea_wm, planeb_wm; + struct intel_watermark_params planea_params, planeb_params; unsigned long line_time_us; int sr_clock, sr_entries = 0; + /* Create copies of the base settings for each pipe */ if (IS_I965GM(dev) || IS_I945GM(dev)) - wm_params = &i945_wm_info; + planea_params = planeb_params = i945_wm_info; else if (IS_I9XX(dev)) - wm_params = &i915_wm_info; + planea_params = planeb_params = i915_wm_info; else - wm_params = &i855_wm_info; - - planea_entries = intel_calculate_wm(planea_clock, wm_params, - pixel_size, latency_ns); - planeb_entries = intel_calculate_wm(planeb_clock, wm_params, - pixel_size, latency_ns); + planea_params = planeb_params = i855_wm_info; - DRM_DEBUG("FIFO entries - A: %d, B: %d\n", planea_entries, - planeb_entries); + /* Grab a couple of global values before we overwrite them */ + total_size = planea_params.fifo_size; + cacheline_size = planea_params.cacheline_size; - if (IS_I9XX(dev)) { - asize = dsparb & 0x7f; - bsize = (dsparb >> DSPARB_CSTART_SHIFT) & 0x7f; - } else { - asize = dsparb & 0x1ff; - bsize = (dsparb >> DSPARB_BEND_SHIFT) & 0x1ff; - } - DRM_DEBUG("FIFO size - A: %d, B: %d\n", asize, bsize); + /* Update per-plane FIFO sizes */ + planea_params.fifo_size = intel_get_fifo_size(dev, 0); + planeb_params.fifo_size = intel_get_fifo_size(dev, 1); - /* Two extra entries for padding */ - awm = asize - (planea_entries + 2); - bwm = bsize - (planeb_entries + 2); - - /* Sanity check against potentially bad FIFO allocations */ - if (awm <= 0) { - /* pipe is on but has too few FIFO entries */ - if (planea_entries != 0) - DRM_DEBUG("plane A needs more FIFO entries\n"); - awm = 1; - } - if (bwm <= 0) { - if (planeb_entries != 0) - DRM_DEBUG("plane B needs more FIFO entries\n"); - bwm = 1; - } + planea_wm = intel_calculate_wm(planea_clock, &planea_params, + pixel_size, latency_ns); + planeb_wm = intel_calculate_wm(planeb_clock, &planeb_params, + pixel_size, latency_ns); + DRM_DEBUG("FIFO watermarks - A: %d, B: %d\n", planea_wm, planeb_wm); /* * Overlay gets an aggressive default since video jitter is bad. */ cwm = 2; - /* Calc sr entries for one pipe configs */ + /* Calc sr entries for one plane configs */ if (!planea_clock || !planeb_clock) { + /* self-refresh has much higher latency */ + const static int sr_latency_ns = 6000; + sr_clock = planea_clock ? planea_clock : planeb_clock; - line_time_us = (sr_hdisplay * 1000) / sr_clock; - sr_entries = (((latency_ns / line_time_us) + 1) * pixel_size * - sr_hdisplay) / 1000; - sr_entries = roundup(sr_entries / wm_params->cacheline_size, 1); - if (sr_entries < wm_params->fifo_size) - srwm = wm_params->fifo_size - sr_entries; + line_time_us = ((sr_hdisplay * 1000) / sr_clock); + + /* Use ns/us then divide to preserve precision */ + sr_entries = (((sr_latency_ns / line_time_us) + 1) * + pixel_size * sr_hdisplay) / 1000; + sr_entries = roundup(sr_entries / cacheline_size, 1); + DRM_DEBUG("self-refresh entries: %d\n", sr_entries); + srwm = total_size - sr_entries; + if (srwm < 0) + srwm = 1; } DRM_DEBUG("Setting FIFO watermarks - A: %d, B: %d, C: %d, SR %d\n", - awm, bwm, cwm, srwm); + planea_wm, planeb_wm, cwm, srwm); - fwater_lo = fwater_lo | ((bwm & 0x3f) << 16) | (awm & 0x3f); - fwater_hi = fwater_hi | (cwm & 0x1f); + fwater_lo = ((planeb_wm & 0x3f) << 16) | (planea_wm & 0x3f); + fwater_hi = (cwm & 0x1f); + + /* Set request length to 8 cachelines per fetch */ + fwater_lo = fwater_lo | (1 << 24) | (1 << 8); + fwater_hi = fwater_hi | (1 << 8); I915_WRITE(FW_BLC, fwater_lo); I915_WRITE(FW_BLC2, fwater_hi); if (IS_I9XX(dev)) - I915_WRITE(FW_BLC_SELF, FW_BLC_SELF_EN | (srwm & 0x3f)); + I915_WRITE(FW_BLC_SELF, (srwm & 0x3f)); } static void i830_update_wm(struct drm_device *dev, int planea_clock, int pixel_size) { struct drm_i915_private *dev_priv = dev->dev_private; - uint32_t dsparb = I915_READ(DSPARB); uint32_t fwater_lo = I915_READ(FW_BLC) & MM_FIFO_WATERMARK; - unsigned int asize, awm; - int planea_entries; - - planea_entries = intel_calculate_wm(planea_clock, &i830_wm_info, - pixel_size, latency_ns); - - asize = dsparb & 0x7f; + int planea_wm; - awm = asize - planea_entries; + i830_wm_info.fifo_size = intel_get_fifo_size(dev, 0); - fwater_lo = fwater_lo | awm; + planea_wm = intel_calculate_wm(planea_clock, &i830_wm_info, + pixel_size, latency_ns); + fwater_lo = fwater_lo | planea_wm; I915_WRITE(FW_BLC, fwater_lo); } @@ -1984,7 +2022,7 @@ static void intel_update_watermarks(struct drm_device *dev) if (enabled <= 0) return; - /* Single pipe configs can enable self refresh */ + /* Single plane configs can enable self refresh */ if (enabled == 1 && IS_IGD(dev)) igd_enable_cxsr(dev, sr_clock, pixel_size); else if (IS_IGD(dev)) -- GitLab From c9d4bc289cd1cd43c3cff97b73efe2b0b5098a92 Mon Sep 17 00:00:00 2001 From: Zhaolei Date: Tue, 14 Jul 2009 17:59:05 +0800 Subject: [PATCH 0038/1342] z2ram: Small cleanup for z2ram.c We should use Z2MINOR_COUNT as range argument in blk_unregister_region() Signed-off-by: Zhao Lei Signed-off-by: Tejun Heo --- drivers/block/z2ram.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/block/z2ram.c b/drivers/block/z2ram.c index 4575171e5be..b2590409f25 100644 --- a/drivers/block/z2ram.c +++ b/drivers/block/z2ram.c @@ -374,7 +374,7 @@ err: static void __exit z2_exit(void) { int i, j; - blk_unregister_region(MKDEV(Z2RAM_MAJOR, 0), 256); + blk_unregister_region(MKDEV(Z2RAM_MAJOR, 0), Z2MINOR_COUNT); unregister_blkdev(Z2RAM_MAJOR, DEVICE_NAME); del_gendisk(z2ram_gendisk); put_disk(z2ram_gendisk); -- GitLab From ed10f95d60d41033d356fdcf88c240d7065bd5b4 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 29 Jun 2009 18:29:11 +1000 Subject: [PATCH 0039/1342] drm/radeon/kms: fix some GART table entry bugs. 1. rv370 can accept 40-bit addresses - also at 24-bit shift not 4 bits 2. rs480 table can be in 40-bit space. - 4 bit shift for top 8 bits 3. rs480 table entries can be in 40-bit space. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 2 +- drivers/gpu/drm/radeon/r300.c | 4 +++- drivers/gpu/drm/radeon/radeon_gart.c | 2 +- drivers/gpu/drm/radeon/rs400.c | 13 +++++++++++-- 4 files changed, 16 insertions(+), 5 deletions(-) diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index c550932a108..1b23106f955 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -110,7 +110,7 @@ int r100_pci_gart_set_page(struct radeon_device *rdev, int i, uint64_t addr) if (i < 0 || i > rdev->gart.num_gpu_pages) { return -EINVAL; } - rdev->gart.table.ram.ptr[i] = cpu_to_le32((uint32_t)addr); + rdev->gart.table.ram.ptr[i] = cpu_to_le32(lower_32_bits(addr)); return 0; } diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c index e2ed5bc0817..cd9ea98e9c6 100644 --- a/drivers/gpu/drm/radeon/r300.c +++ b/drivers/gpu/drm/radeon/r300.c @@ -150,7 +150,9 @@ int rv370_pcie_gart_set_page(struct radeon_device *rdev, int i, uint64_t addr) if (i < 0 || i > rdev->gart.num_gpu_pages) { return -EINVAL; } - addr = (((u32)addr) >> 8) | ((upper_32_bits(addr) & 0xff) << 4) | 0xC; + addr = (lower_32_bits(addr) >> 8) | + ((upper_32_bits(addr) & 0xff) << 24) | + 0xc; writel(cpu_to_le32(addr), ((void __iomem *)ptr) + (i * 4)); return 0; } diff --git a/drivers/gpu/drm/radeon/radeon_gart.c b/drivers/gpu/drm/radeon/radeon_gart.c index d343a15316e..2977539880f 100644 --- a/drivers/gpu/drm/radeon/radeon_gart.c +++ b/drivers/gpu/drm/radeon/radeon_gart.c @@ -177,7 +177,7 @@ int radeon_gart_bind(struct radeon_device *rdev, unsigned offset, return -ENOMEM; } rdev->gart.pages[p] = pagelist[i]; - page_base = (uint32_t)rdev->gart.pages_addr[p]; + page_base = rdev->gart.pages_addr[p]; for (j = 0; j < (PAGE_SIZE / 4096); j++, t++) { radeon_gart_set_page(rdev, t, page_base); page_base += 4096; diff --git a/drivers/gpu/drm/radeon/rs400.c b/drivers/gpu/drm/radeon/rs400.c index cc074b5a8f7..3275de4b6e3 100644 --- a/drivers/gpu/drm/radeon/rs400.c +++ b/drivers/gpu/drm/radeon/rs400.c @@ -164,7 +164,9 @@ int rs400_gart_enable(struct radeon_device *rdev) WREG32(RADEON_BUS_CNTL, tmp); } /* Table should be in 32bits address space so ignore bits above. */ - tmp = rdev->gart.table_addr & 0xfffff000; + tmp = (u32)rdev->gart.table_addr & 0xfffff000; + tmp |= (upper_32_bits(rdev->gart.table_addr) & 0xff) << 4; + WREG32_MC(RS480_GART_BASE, tmp); /* TODO: more tweaking here */ WREG32_MC(RS480_GART_FEATURE_ID, @@ -201,10 +203,17 @@ void rs400_gart_disable(struct radeon_device *rdev) int rs400_gart_set_page(struct radeon_device *rdev, int i, uint64_t addr) { + uint32_t entry; + if (i < 0 || i > rdev->gart.num_gpu_pages) { return -EINVAL; } - rdev->gart.table.ram.ptr[i] = cpu_to_le32(((uint32_t)addr) | 0xC); + + entry = (lower_32_bits(addr) & PAGE_MASK) | + ((upper_32_bits(addr) & 0xff) << 4) | + 0xc; + entry = cpu_to_le32(entry); + rdev->gart.table.ram.ptr[i] = entry; return 0; } -- GitLab From 4c9bc75cbc6f2f447a38a123aa6e0605fab3cb7a Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 29 Jun 2009 18:29:12 +1000 Subject: [PATCH 0040/1342] drm/radeon/kms: mmio base/size should be resource_size_t. Unsigned long is incorrect for 64-bit resources on 32-bit hw. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index d61f2fc61df..e7662ba9abf 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -594,8 +594,8 @@ struct radeon_device { struct radeon_object *fbdev_robj; struct radeon_framebuffer *fbdev_rfb; /* Register mmio */ - unsigned long rmmio_base; - unsigned long rmmio_size; + resource_size_t rmmio_base; + resource_size_t rmmio_size; void *rmmio; radeon_rreg_t mm_rreg; radeon_wreg_t mm_wreg; -- GitLab From 6cdf65855cf884712532fc72770baaef7bdf1b9a Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 29 Jun 2009 18:29:13 +1000 Subject: [PATCH 0041/1342] drm/radeon/kms: remove IB flushing trick. If there is a problem then this is hiding it, we shouldn't ever need to flush the IB. Either the buffers are: WB - caching just works. WC - no need to do explicit flush, the MB + readback will do it Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_ring.c | 15 +-------------- 1 file changed, 1 insertion(+), 14 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon_ring.c b/drivers/gpu/drm/radeon/radeon_ring.c index a853261d188..60d159308b8 100644 --- a/drivers/gpu/drm/radeon/radeon_ring.c +++ b/drivers/gpu/drm/radeon/radeon_ring.c @@ -126,32 +126,19 @@ static void radeon_ib_align(struct radeon_device *rdev, struct radeon_ib *ib) } } -static void radeon_ib_cpu_flush(struct radeon_device *rdev, - struct radeon_ib *ib) -{ - unsigned long tmp; - unsigned i; - - /* To force CPU cache flush ugly but seems reliable */ - for (i = 0; i < ib->length_dw; i += (rdev->cp.align_mask + 1)) { - tmp = readl(&ib->ptr[i]); - } -} - int radeon_ib_schedule(struct radeon_device *rdev, struct radeon_ib *ib) { int r = 0; mutex_lock(&rdev->ib_pool.mutex); radeon_ib_align(rdev, ib); - radeon_ib_cpu_flush(rdev, ib); if (!ib->length_dw || !rdev->cp.ready) { /* TODO: Nothings in the ib we should report. */ mutex_unlock(&rdev->ib_pool.mutex); DRM_ERROR("radeon: couldn't schedule IB(%lu).\n", ib->idx); return -EINVAL; } - /* 64 dwords should be enought for fence too */ + /* 64 dwords should be enough for fence too */ r = radeon_ring_lock(rdev, 64); if (r) { DRM_ERROR("radeon: scheduling IB failled (%d).\n", r); -- GitLab From 4162338a1dab388474d4115289d1d7071623f04d Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Thu, 9 Jul 2009 15:04:19 +1000 Subject: [PATCH 0042/1342] drm/radeon/kms: set crtc and cursor offsets correctly on legacy chips. The crtc and cursor offsets on the legacy chips are offset from DISPLAY_BASE_ADDR. The code worked if display base addr was at 0, but otherwise falls to pieces. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_cursor.c | 2 +- drivers/gpu/drm/radeon/radeon_legacy_crtc.c | 11 +++++++---- drivers/gpu/drm/radeon/radeon_mode.h | 1 + 3 files changed, 9 insertions(+), 5 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon_cursor.c b/drivers/gpu/drm/radeon/radeon_cursor.c index 5232441f119..5f8ce370c4f 100644 --- a/drivers/gpu/drm/radeon/radeon_cursor.c +++ b/drivers/gpu/drm/radeon/radeon_cursor.c @@ -113,7 +113,7 @@ static void radeon_set_cursor(struct drm_crtc *crtc, struct drm_gem_object *obj, WREG32(AVIVO_D1CUR_SURFACE_ADDRESS + radeon_crtc->crtc_offset, gpu_addr); else /* offset is from DISP(2)_BASE_ADDRESS */ - WREG32(RADEON_CUR_OFFSET + radeon_crtc->crtc_offset, gpu_addr); + WREG32(RADEON_CUR_OFFSET + radeon_crtc->crtc_offset, (gpu_addr-radeon_crtc->legacy_display_base_addr)); } int radeon_crtc_cursor_set(struct drm_crtc *crtc, diff --git a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c index 8086ecf7f03..14c1a5107fc 100644 --- a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c +++ b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c @@ -244,7 +244,12 @@ int radeon_crtc_set_base(struct drm_crtc *crtc, int x, int y, if (radeon_gem_object_pin(obj, RADEON_GEM_DOMAIN_VRAM, &base)) { return -EINVAL; } - crtc_offset = (u32)base; + /* if scanout was in GTT this really wouldn't work */ + /* crtc offset is from display base addr not FB location */ + radeon_crtc->legacy_display_base_addr = rdev->mc.vram_location; + + base -= radeon_crtc->legacy_display_base_addr; + crtc_offset_cntl = 0; pitch_pixels = crtc->fb->pitch / (crtc->fb->bits_per_pixel / 8); @@ -303,11 +308,9 @@ int radeon_crtc_set_base(struct drm_crtc *crtc, int x, int y, base &= ~7; - /* update sarea TODO */ - crtc_offset = (u32)base; - WREG32(RADEON_DISPLAY_BASE_ADDR + radeon_crtc->crtc_offset, rdev->mc.vram_location); + WREG32(RADEON_DISPLAY_BASE_ADDR + radeon_crtc->crtc_offset, radeon_crtc->legacy_display_base_addr); if (ASIC_IS_R300(rdev)) { if (radeon_crtc->crtc_id) diff --git a/drivers/gpu/drm/radeon/radeon_mode.h b/drivers/gpu/drm/radeon/radeon_mode.h index 9173b687462..86f766e868e 100644 --- a/drivers/gpu/drm/radeon/radeon_mode.h +++ b/drivers/gpu/drm/radeon/radeon_mode.h @@ -185,6 +185,7 @@ struct radeon_crtc { uint64_t cursor_addr; int cursor_width; int cursor_height; + uint32_t legacy_display_base_addr; }; #define RADEON_USE_RMX 1 -- GitLab From 3e43d82125952826202a8cd20ba84a66f3ff8808 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Thu, 9 Jul 2009 15:04:18 +1000 Subject: [PATCH 0043/1342] drm/radeon/kms: respect TOM on rs100->rs480 IGP variants. Normally we are free to place VRAM where we want in the GPUs memory address space, however on IGP chips the VRAM is actual RAM, and no special translation or aperture is used inside the GPU MC. So when you move the VRAM aperture away from the TOM register, you actually move it into main memory and can trash things quite badly. This commit makes the code respect the TOM location for MC_FB_LOCATION. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 5 ++++- drivers/gpu/drm/radeon/rs400.c | 6 ++++-- 2 files changed, 8 insertions(+), 3 deletions(-) diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index 1b23106f955..a3db56bb013 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -215,7 +215,6 @@ int r100_mc_init(struct radeon_device *rdev) r100_pci_gart_disable(rdev); /* Setup GPU memory space */ - rdev->mc.vram_location = 0xFFFFFFFFUL; rdev->mc.gtt_location = 0xFFFFFFFFUL; if (rdev->flags & RADEON_IS_AGP) { r = radeon_agp_init(rdev); @@ -1265,6 +1264,8 @@ void r100_vram_info(struct radeon_device *rdev) /* read NB_TOM to get the amount of ram stolen for the GPU */ tom = RREG32(RADEON_NB_TOM); rdev->mc.vram_size = (((tom >> 16) - (tom & 0xffff) + 1) << 16); + /* for IGPs we need to keep VRAM where it was put by the BIOS */ + rdev->mc.vram_location = (tom & 0xffff) << 16; WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); } else { rdev->mc.vram_size = RREG32(RADEON_CONFIG_MEMSIZE); @@ -1275,6 +1276,8 @@ void r100_vram_info(struct radeon_device *rdev) rdev->mc.vram_size = 8192 * 1024; WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); } + /* let driver place VRAM */ + rdev->mc.vram_location = 0xFFFFFFFFUL; } rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); diff --git a/drivers/gpu/drm/radeon/rs400.c b/drivers/gpu/drm/radeon/rs400.c index 3275de4b6e3..a18d053065c 100644 --- a/drivers/gpu/drm/radeon/rs400.c +++ b/drivers/gpu/drm/radeon/rs400.c @@ -235,7 +235,6 @@ int rs400_mc_init(struct radeon_device *rdev) rdev->mc.gtt_location = rdev->mc.vram_size; rdev->mc.gtt_location += (rdev->mc.gtt_size - 1); rdev->mc.gtt_location &= ~(rdev->mc.gtt_size - 1); - rdev->mc.vram_location = 0xFFFFFFFFUL; r = radeon_mc_setup(rdev); if (r) { return r; @@ -305,7 +304,10 @@ void rs400_vram_info(struct radeon_device *rdev) rdev->mc.vram_size = (((tom >> 16) - (tom & 0xffff) + 1) << 16); WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); - /* Could aper size report 0 ? */ + /* RS480 IGPs don't seem to translate to main RAM, they + * just reserve and scan out of it. So setting VRAM location + * to say 0, will actually trash the OS. */ + rdev->mc.vram_location = (tom & 0xffff) << 16; rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); } -- GitLab From 531369e62649bb8f31217cc0bf33ee6f89f1dff6 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 29 Jun 2009 11:21:25 +1000 Subject: [PATCH 0044/1342] drm/radeon: fix support for vline relocations. Userspace sends us a special relocation type to sync video/exa to vlines to avoid tearing, this deals with the relocation in the kernel, it picks the correct crtc and avoids issues where crtcs are disabled. This version also parses the wait until to make sure it isn't trying to do anything evil. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 105 ++++++++++++++++++++++++++++++ drivers/gpu/drm/radeon/r300.c | 13 +++- drivers/gpu/drm/radeon/r500_reg.h | 2 + drivers/gpu/drm/radeon/rv515.c | 23 +++++-- 4 files changed, 137 insertions(+), 6 deletions(-) diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index a3db56bb013..154648a2c02 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -751,6 +751,102 @@ int r100_cs_packet_parse(struct radeon_cs_parser *p, return 0; } +/** + * r100_cs_packet_next_vline() - parse userspace VLINE packet + * @parser: parser structure holding parsing context. + * + * Userspace sends a special sequence for VLINE waits. + * PACKET0 - VLINE_START_END + value + * PACKET0 - WAIT_UNTIL +_value + * RELOC (P3) - crtc_id in reloc. + * + * This function parses this and relocates the VLINE START END + * and WAIT UNTIL packets to the correct crtc. + * It also detects a switched off crtc and nulls out the + * wait in that case. + */ +int r100_cs_packet_parse_vline(struct radeon_cs_parser *p) +{ + struct radeon_cs_chunk *ib_chunk; + struct drm_mode_object *obj; + struct drm_crtc *crtc; + struct radeon_crtc *radeon_crtc; + struct radeon_cs_packet p3reloc, waitreloc; + int crtc_id; + int r; + uint32_t header, h_idx, reg; + + ib_chunk = &p->chunks[p->chunk_ib_idx]; + + /* parse the wait until */ + r = r100_cs_packet_parse(p, &waitreloc, p->idx); + if (r) + return r; + + /* check its a wait until and only 1 count */ + if (waitreloc.reg != RADEON_WAIT_UNTIL || + waitreloc.count != 0) { + DRM_ERROR("vline wait had illegal wait until segment\n"); + r = -EINVAL; + return r; + } + + if (ib_chunk->kdata[waitreloc.idx + 1] != RADEON_WAIT_CRTC_VLINE) { + DRM_ERROR("vline wait had illegal wait until\n"); + r = -EINVAL; + return r; + } + + /* jump over the NOP */ + r = r100_cs_packet_parse(p, &p3reloc, p->idx); + if (r) + return r; + + h_idx = p->idx - 2; + p->idx += waitreloc.count; + p->idx += p3reloc.count; + + header = ib_chunk->kdata[h_idx]; + crtc_id = ib_chunk->kdata[h_idx + 5]; + reg = ib_chunk->kdata[h_idx] >> 2; + mutex_lock(&p->rdev->ddev->mode_config.mutex); + obj = drm_mode_object_find(p->rdev->ddev, crtc_id, DRM_MODE_OBJECT_CRTC); + if (!obj) { + DRM_ERROR("cannot find crtc %d\n", crtc_id); + r = -EINVAL; + goto out; + } + crtc = obj_to_crtc(obj); + radeon_crtc = to_radeon_crtc(crtc); + crtc_id = radeon_crtc->crtc_id; + + if (!crtc->enabled) { + /* if the CRTC isn't enabled - we need to nop out the wait until */ + ib_chunk->kdata[h_idx + 2] = PACKET2(0); + ib_chunk->kdata[h_idx + 3] = PACKET2(0); + } else if (crtc_id == 1) { + switch (reg) { + case AVIVO_D1MODE_VLINE_START_END: + header &= R300_CP_PACKET0_REG_MASK; + header |= AVIVO_D2MODE_VLINE_START_END >> 2; + break; + case RADEON_CRTC_GUI_TRIG_VLINE: + header &= R300_CP_PACKET0_REG_MASK; + header |= RADEON_CRTC2_GUI_TRIG_VLINE >> 2; + break; + default: + DRM_ERROR("unknown crtc reloc\n"); + r = -EINVAL; + goto out; + } + ib_chunk->kdata[h_idx] = header; + ib_chunk->kdata[h_idx + 3] |= RADEON_ENG_DISPLAY_SELECT_CRTC1; + } +out: + mutex_unlock(&p->rdev->ddev->mode_config.mutex); + return r; +} + /** * r100_cs_packet_next_reloc() - parse next packet which should be reloc packet3 * @parser: parser structure holding parsing context. @@ -824,6 +920,15 @@ static int r100_packet0_check(struct radeon_cs_parser *p, } for (i = 0; i <= pkt->count; i++, idx++, reg += 4) { switch (reg) { + case RADEON_CRTC_GUI_TRIG_VLINE: + r = r100_cs_packet_parse_vline(p); + if (r) { + DRM_ERROR("No reloc for ib[%d]=0x%04X\n", + idx, reg); + r100_cs_dump_packet(p, pkt); + return r; + } + break; /* FIXME: only allow PACKET3 blit? easier to check for out of * range access */ case RADEON_DST_PITCH_OFFSET: diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c index cd9ea98e9c6..656d9238bb0 100644 --- a/drivers/gpu/drm/radeon/r300.c +++ b/drivers/gpu/drm/radeon/r300.c @@ -44,6 +44,7 @@ int r100_gui_wait_for_idle(struct radeon_device *rdev); int r100_cs_packet_parse(struct radeon_cs_parser *p, struct radeon_cs_packet *pkt, unsigned idx); +int r100_cs_packet_parse_vline(struct radeon_cs_parser *p); int r100_cs_packet_next_reloc(struct radeon_cs_parser *p, struct radeon_cs_reloc **cs_reloc); int r100_cs_parse_packet0(struct radeon_cs_parser *p, @@ -972,7 +973,7 @@ static inline void r300_cs_track_clear(struct r300_cs_track *track) static const unsigned r300_reg_safe_bm[159] = { 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFBF, 0xFFFFFFFF, 0xFFFFFFBF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, @@ -1029,6 +1030,16 @@ static int r300_packet0_check(struct radeon_cs_parser *p, ib_chunk = &p->chunks[p->chunk_ib_idx]; track = (struct r300_cs_track*)p->track; switch(reg) { + case AVIVO_D1MODE_VLINE_START_END: + case RADEON_CRTC_GUI_TRIG_VLINE: + r = r100_cs_packet_parse_vline(p); + if (r) { + DRM_ERROR("No reloc for ib[%d]=0x%04X\n", + idx, reg); + r100_cs_dump_packet(p, pkt); + return r; + } + break; case RADEON_DST_PITCH_OFFSET: case RADEON_SRC_PITCH_OFFSET: r = r100_cs_packet_next_reloc(p, &reloc); diff --git a/drivers/gpu/drm/radeon/r500_reg.h b/drivers/gpu/drm/radeon/r500_reg.h index 9070a1c2ce2..036691b38cb 100644 --- a/drivers/gpu/drm/radeon/r500_reg.h +++ b/drivers/gpu/drm/radeon/r500_reg.h @@ -445,6 +445,7 @@ #define AVIVO_D1MODE_DATA_FORMAT 0x6528 # define AVIVO_D1MODE_INTERLEAVE_EN (1 << 0) #define AVIVO_D1MODE_DESKTOP_HEIGHT 0x652C +#define AVIVO_D1MODE_VLINE_START_END 0x6538 #define AVIVO_D1MODE_VIEWPORT_START 0x6580 #define AVIVO_D1MODE_VIEWPORT_SIZE 0x6584 #define AVIVO_D1MODE_EXT_OVERSCAN_LEFT_RIGHT 0x6588 @@ -496,6 +497,7 @@ #define AVIVO_D2CUR_SIZE 0x6c10 #define AVIVO_D2CUR_POSITION 0x6c14 +#define AVIVO_D2MODE_VLINE_START_END 0x6d38 #define AVIVO_D2MODE_VIEWPORT_START 0x6d80 #define AVIVO_D2MODE_VIEWPORT_SIZE 0x6d84 #define AVIVO_D2MODE_EXT_OVERSCAN_LEFT_RIGHT 0x6d88 diff --git a/drivers/gpu/drm/radeon/rv515.c b/drivers/gpu/drm/radeon/rv515.c index ffea37b1b3e..d1384d3991a 100644 --- a/drivers/gpu/drm/radeon/rv515.c +++ b/drivers/gpu/drm/radeon/rv515.c @@ -509,9 +509,9 @@ int rv515_debugfs_ga_info_init(struct radeon_device *rdev) /* * Asic initialization */ -static const unsigned r500_reg_safe_bm[159] = { +static const unsigned r500_reg_safe_bm[219] = { + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFBF, 0xFFFFFFFF, 0xFFFFFFBF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, @@ -549,11 +549,24 @@ static const unsigned r500_reg_safe_bm[159] = { 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFF80FFFF, 0x00000000, 0x00000000, 0x00000000, 0x00000000, - 0x0003FC01, 0x3FFFFCF8, 0xFE800B19, + 0x0003FC01, 0x3FFFFCF8, 0xFE800B19, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, }; - - int rv515_init(struct radeon_device *rdev) { rdev->config.r300.reg_safe_bm = r500_reg_safe_bm; -- GitLab From d1724078d6a01177c1db4ea0b75fda1ca8a73d57 Mon Sep 17 00:00:00 2001 From: Thomas Hellstrom Date: Wed, 24 Jun 2009 19:57:35 +0200 Subject: [PATCH 0045/1342] ttm: Make messages more readable. Signed-off-by: Thomas Hellstrom Signed-off-by: Dave Airlie --- include/drm/ttm/ttm_module.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/drm/ttm/ttm_module.h b/include/drm/ttm/ttm_module.h index 889a4c7958a..d1d433834e4 100644 --- a/include/drm/ttm/ttm_module.h +++ b/include/drm/ttm/ttm_module.h @@ -33,7 +33,7 @@ #include -#define TTM_PFX "[TTM]" +#define TTM_PFX "[TTM] " enum ttm_global_types { TTM_GLOBAL_TTM_MEM = 0, -- GitLab From ae3e8122cbf8f9301369f276f4179aa6ec1b5b9c Mon Sep 17 00:00:00 2001 From: Thomas Hellstrom Date: Wed, 24 Jun 2009 19:57:34 +0200 Subject: [PATCH 0046/1342] ttm: Fix caching mode selection. A bug caused a new caching state to be selected on each buffer object validation regardless of the current caching state. Moreover, a caching state could be selected that wasn't supported by the memory type. Signed-off-by: Thomas Hellstrom Signed-off-by: Dave Airlie --- drivers/gpu/drm/ttm/ttm_bo.c | 51 +++++++++++++++++++++++++++--------- 1 file changed, 39 insertions(+), 12 deletions(-) diff --git a/drivers/gpu/drm/ttm/ttm_bo.c b/drivers/gpu/drm/ttm/ttm_bo.c index c1c407f7cca..a753598a5e3 100644 --- a/drivers/gpu/drm/ttm/ttm_bo.c +++ b/drivers/gpu/drm/ttm/ttm_bo.c @@ -655,31 +655,52 @@ retry_pre_get: return 0; } +static uint32_t ttm_bo_select_caching(struct ttm_mem_type_manager *man, + uint32_t cur_placement, + uint32_t proposed_placement) +{ + uint32_t caching = proposed_placement & TTM_PL_MASK_CACHING; + uint32_t result = proposed_placement & ~TTM_PL_MASK_CACHING; + + /** + * Keep current caching if possible. + */ + + if ((cur_placement & caching) != 0) + result |= (cur_placement & caching); + else if ((man->default_caching & caching) != 0) + result |= man->default_caching; + else if ((TTM_PL_FLAG_CACHED & caching) != 0) + result |= TTM_PL_FLAG_CACHED; + else if ((TTM_PL_FLAG_WC & caching) != 0) + result |= TTM_PL_FLAG_WC; + else if ((TTM_PL_FLAG_UNCACHED & caching) != 0) + result |= TTM_PL_FLAG_UNCACHED; + + return result; +} + + static bool ttm_bo_mt_compatible(struct ttm_mem_type_manager *man, bool disallow_fixed, uint32_t mem_type, - uint32_t mask, uint32_t *res_mask) + uint32_t proposed_placement, + uint32_t *masked_placement) { uint32_t cur_flags = ttm_bo_type_flags(mem_type); if ((man->flags & TTM_MEMTYPE_FLAG_FIXED) && disallow_fixed) return false; - if ((cur_flags & mask & TTM_PL_MASK_MEM) == 0) + if ((cur_flags & proposed_placement & TTM_PL_MASK_MEM) == 0) return false; - if ((mask & man->available_caching) == 0) + if ((proposed_placement & man->available_caching) == 0) return false; - if (mask & man->default_caching) - cur_flags |= man->default_caching; - else if (mask & TTM_PL_FLAG_CACHED) - cur_flags |= TTM_PL_FLAG_CACHED; - else if (mask & TTM_PL_FLAG_WC) - cur_flags |= TTM_PL_FLAG_WC; - else - cur_flags |= TTM_PL_FLAG_UNCACHED; - *res_mask = cur_flags; + cur_flags |= (proposed_placement & man->available_caching); + + *masked_placement = cur_flags; return true; } @@ -723,6 +744,9 @@ int ttm_bo_mem_space(struct ttm_buffer_object *bo, if (!type_ok) continue; + cur_flags = ttm_bo_select_caching(man, bo->mem.placement, + cur_flags); + if (mem_type == TTM_PL_SYSTEM) break; @@ -779,6 +803,9 @@ int ttm_bo_mem_space(struct ttm_buffer_object *bo, proposed_placement, &cur_flags)) continue; + cur_flags = ttm_bo_select_caching(man, bo->mem.placement, + cur_flags); + ret = ttm_bo_mem_force_space(bdev, mem, mem_type, interruptible, no_wait); -- GitLab From 848577ee27f704231b1860ae987a1be78b88b06e Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Wed, 8 Jul 2009 16:15:30 -0400 Subject: [PATCH 0047/1342] drm/radeon/kms: fix quirk for MSI laptop The line mux for the connector in the bios tables is used for enumerating drm connectors. Since this laptop has a quirk where the same line much is listed for both VGA and LVDS, the connectors get combined. Setting the line mux on LVDS to an unused value prevents both encoders from being combined into the same connector. This should fix bko bug 13720. Signed-off-by: Alex Deucher Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_atombios.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon_atombios.c b/drivers/gpu/drm/radeon/radeon_atombios.c index 1f5a1a49098..fcfe5c02d74 100644 --- a/drivers/gpu/drm/radeon/radeon_atombios.c +++ b/drivers/gpu/drm/radeon/radeon_atombios.c @@ -103,7 +103,8 @@ static inline struct radeon_i2c_bus_rec radeon_lookup_gpio(struct drm_device static bool radeon_atom_apply_quirks(struct drm_device *dev, uint32_t supported_device, int *connector_type, - struct radeon_i2c_bus_rec *i2c_bus) + struct radeon_i2c_bus_rec *i2c_bus, + uint8_t *line_mux) { /* Asus M2A-VM HDMI board lists the DVI port as HDMI */ @@ -127,8 +128,10 @@ static bool radeon_atom_apply_quirks(struct drm_device *dev, if ((dev->pdev->device == 0x5653) && (dev->pdev->subsystem_vendor == 0x1462) && (dev->pdev->subsystem_device == 0x0291)) { - if (*connector_type == DRM_MODE_CONNECTOR_LVDS) + if (*connector_type == DRM_MODE_CONNECTOR_LVDS) { i2c_bus->valid = false; + *line_mux = 53; + } } /* Funky macbooks */ @@ -526,7 +529,7 @@ bool radeon_get_atom_connector_info_from_supported_devices_table(struct if (!radeon_atom_apply_quirks (dev, (1 << i), &bios_connectors[i].connector_type, - &bios_connectors[i].ddc_bus)) + &bios_connectors[i].ddc_bus, &bios_connectors[i].line_mux)) continue; bios_connectors[i].valid = true; -- GitLab From 2007d633d639c896396e4c4b53b38068f3831307 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Wed, 8 Jul 2009 16:17:23 -0400 Subject: [PATCH 0048/1342] drm/radeon/kms: get lvds info for DIG LVTMA and UNIPHY encoders MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Noticed by RafaÅ‚ MiÅ‚ecki on dri-devel. On r6xx/r7xx hardware, laptop panels can be driven by KLDSCP_LVTMA or UNIPHY. Signed-off-by: Alex Deucher Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_encoders.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon_encoders.c b/drivers/gpu/drm/radeon/radeon_encoders.c index c8ef0d14ffa..ea15284e758 100644 --- a/drivers/gpu/drm/radeon/radeon_encoders.c +++ b/drivers/gpu/drm/radeon/radeon_encoders.c @@ -1700,8 +1700,14 @@ radeon_add_atom_encoder(struct drm_device *dev, uint32_t encoder_id, uint32_t su case ENCODER_OBJECT_ID_INTERNAL_KLDSCP_LVTMA: case ENCODER_OBJECT_ID_INTERNAL_UNIPHY1: case ENCODER_OBJECT_ID_INTERNAL_UNIPHY2: - drm_encoder_init(dev, encoder, &radeon_atom_enc_funcs, DRM_MODE_ENCODER_TMDS); - radeon_encoder->enc_priv = radeon_atombios_set_dig_info(radeon_encoder); + if (radeon_encoder->devices & (ATOM_DEVICE_LCD_SUPPORT)) { + radeon_encoder->rmx_type = RMX_FULL; + drm_encoder_init(dev, encoder, &radeon_atom_enc_funcs, DRM_MODE_ENCODER_LVDS); + radeon_encoder->enc_priv = radeon_atombios_get_lvds_info(radeon_encoder); + } else { + drm_encoder_init(dev, encoder, &radeon_atom_enc_funcs, DRM_MODE_ENCODER_TMDS); + radeon_encoder->enc_priv = radeon_atombios_set_dig_info(radeon_encoder); + } drm_encoder_helper_add(encoder, &radeon_atom_dig_helper_funcs); break; } -- GitLab From e7168cab5bbac0a0e5413fd55ba0e92555bf860d Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Thu, 9 Jul 2009 16:01:42 +1000 Subject: [PATCH 0049/1342] drm/radeon/kms: fix vram vs aper size check. Fix this to be correct like the DDX code, looks like a typo on transfer to the kernel. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_device.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c index f97563db4e5..332911267eb 100644 --- a/drivers/gpu/drm/radeon/radeon_device.c +++ b/drivers/gpu/drm/radeon/radeon_device.c @@ -552,7 +552,7 @@ int radeon_device_init(struct radeon_device *rdev, * for RN50/M6/M7 - Novell bug 204882 ? */ if (rdev->mc.vram_size < rdev->mc.aper_size) { - rdev->mc.aper_size = rdev->mc.vram_size; + rdev->mc.vram_size = rdev->mc.aper_size; } /* Add an MTRR for the VRAM */ rdev->mc.vram_mtrr = mtrr_add(rdev->mc.aper_base, rdev->mc.aper_size, -- GitLab From 5176fdc4c5873e52f9cb6e166d80e843847e7eb4 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Tue, 30 Jun 2009 11:47:14 +1000 Subject: [PATCH 0050/1342] drm/radeon/kms: drop zero length CS indirect buffers. If userspace sends a zero length IB, it really shouldn't have bothered so EINVAL it. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_cs.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/radeon/radeon_cs.c b/drivers/gpu/drm/radeon/radeon_cs.c index b843f9bdfb1..a169067efc4 100644 --- a/drivers/gpu/drm/radeon/radeon_cs.c +++ b/drivers/gpu/drm/radeon/radeon_cs.c @@ -127,17 +127,23 @@ int radeon_cs_parser_init(struct radeon_cs_parser *p, void *data) sizeof(struct drm_radeon_cs_chunk))) { return -EFAULT; } + p->chunks[i].length_dw = user_chunk.length_dw; + p->chunks[i].kdata = NULL; p->chunks[i].chunk_id = user_chunk.chunk_id; + if (p->chunks[i].chunk_id == RADEON_CHUNK_ID_RELOCS) { p->chunk_relocs_idx = i; } if (p->chunks[i].chunk_id == RADEON_CHUNK_ID_IB) { p->chunk_ib_idx = i; + /* zero length IB isn't useful */ + if (p->chunks[i].length_dw == 0) + return -EINVAL; } + p->chunks[i].length_dw = user_chunk.length_dw; cdata = (uint32_t *)(unsigned long)user_chunk.chunk_data; - p->chunks[i].kdata = NULL; size = p->chunks[i].length_dw * sizeof(uint32_t); p->chunks[i].kdata = kzalloc(size, GFP_KERNEL); if (p->chunks[i].kdata == NULL) { -- GitLab From 77bd36f014bc5a3f28507a4e86a81b2b3d2439c3 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Fri, 10 Jul 2009 09:33:00 +1000 Subject: [PATCH 0051/1342] drm/radeon/kms: don't swap PCIEGART PTEs in VRAM. On powerpc, since we aren't using any hw swappers, this will get flipped around by default in hw. tested on a G5 + rv515. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r300.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c index 656d9238bb0..6435d659cbd 100644 --- a/drivers/gpu/drm/radeon/r300.c +++ b/drivers/gpu/drm/radeon/r300.c @@ -154,7 +154,10 @@ int rv370_pcie_gart_set_page(struct radeon_device *rdev, int i, uint64_t addr) addr = (lower_32_bits(addr) >> 8) | ((upper_32_bits(addr) & 0xff) << 24) | 0xc; - writel(cpu_to_le32(addr), ((void __iomem *)ptr) + (i * 4)); + /* on x86 we want this to be CPU endian, on powerpc + * on powerpc without HW swappers, it'll get swapped on way + * into VRAM - so no need for cpu_to_le32 on VRAM tables */ + writel(addr, ((void __iomem *)ptr) + (i * 4)); return 0; } -- GitLab From 61b576dbbe6a19d102c025ebc102a0749e2d3c80 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Michel=20D=C3=A4nzer?= Date: Wed, 24 Jun 2009 00:12:55 +1000 Subject: [PATCH 0052/1342] drm/radeon: Endianness fixes for radeondrmfb. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit For now handle it via r/g/b offsets and disallow 16 bpp modes on big endian machines. Signed-off-by: Michel Dänzer Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_fb.c | 53 ++++++++++++++++++++++++++++-- 1 file changed, 50 insertions(+), 3 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon_fb.c b/drivers/gpu/drm/radeon/radeon_fb.c index 9e8f191eb64..260870a29d8 100644 --- a/drivers/gpu/drm/radeon/radeon_fb.c +++ b/drivers/gpu/drm/radeon/radeon_fb.c @@ -101,9 +101,10 @@ static int radeonfb_setcolreg(unsigned regno, break; case 24: case 32: - fb->pseudo_palette[regno] = ((red & 0xff00) << 8) | - (green & 0xff00) | - ((blue & 0xff00) >> 8); + fb->pseudo_palette[regno] = + (((red >> 8) & 0xff) << info->var.red.offset) | + (((green >> 8) & 0xff) << info->var.green.offset) | + (((blue >> 8) & 0xff) << info->var.blue.offset); break; } } @@ -154,6 +155,7 @@ static int radeonfb_check_var(struct fb_var_screeninfo *var, var->transp.length = 0; var->transp.offset = 0; break; +#ifdef __LITTLE_ENDIAN case 15: var->red.offset = 10; var->green.offset = 5; @@ -194,6 +196,28 @@ static int radeonfb_check_var(struct fb_var_screeninfo *var, var->transp.length = 8; var->transp.offset = 24; break; +#else + case 24: + var->red.offset = 8; + var->green.offset = 16; + var->blue.offset = 24; + var->red.length = 8; + var->green.length = 8; + var->blue.length = 8; + var->transp.length = 0; + var->transp.offset = 0; + break; + case 32: + var->red.offset = 8; + var->green.offset = 16; + var->blue.offset = 24; + var->red.length = 8; + var->green.length = 8; + var->blue.length = 8; + var->transp.length = 8; + var->transp.offset = 0; + break; +#endif default: return -EINVAL; } @@ -600,6 +624,7 @@ int radeonfb_create(struct radeon_device *rdev, info->var.transp.offset = 0; info->var.transp.length = 0; break; +#ifdef __LITTLE_ENDIAN case 15: info->var.red.offset = 10; info->var.green.offset = 5; @@ -639,7 +664,29 @@ int radeonfb_create(struct radeon_device *rdev, info->var.transp.offset = 24; info->var.transp.length = 8; break; +#else + case 24: + info->var.red.offset = 8; + info->var.green.offset = 16; + info->var.blue.offset = 24; + info->var.red.length = 8; + info->var.green.length = 8; + info->var.blue.length = 8; + info->var.transp.offset = 0; + info->var.transp.length = 0; + break; + case 32: + info->var.red.offset = 8; + info->var.green.offset = 16; + info->var.blue.offset = 24; + info->var.red.length = 8; + info->var.green.length = 8; + info->var.blue.length = 8; + info->var.transp.offset = 0; + info->var.transp.length = 8; + break; default: +#endif break; } -- GitLab From ad49f501867cba87e1e45e5ebae0b12435d68bf1 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Fri, 10 Jul 2009 22:36:26 +1000 Subject: [PATCH 0053/1342] drm/ttm/radeon: add dma32 support. This add support for using dma32 memory on gpus that really need it. Currently IGPs are left without DMA32 but we might need to change that unless we can fix rs690. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon.h | 1 + drivers/gpu/drm/radeon/radeon_device.c | 17 +++++++++++++++-- drivers/gpu/drm/radeon/radeon_ttm.c | 3 ++- drivers/gpu/drm/ttm/ttm_bo.c | 7 ++++++- drivers/gpu/drm/ttm/ttm_tt.c | 9 +++++++-- include/drm/ttm/ttm_bo_driver.h | 5 ++++- 6 files changed, 35 insertions(+), 7 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index e7662ba9abf..3060ce14071 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -624,6 +624,7 @@ struct radeon_device { bool gpu_lockup; bool shutdown; bool suspend; + bool need_dma32; }; int radeon_device_init(struct radeon_device *rdev, diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c index 332911267eb..27a5ac96995 100644 --- a/drivers/gpu/drm/radeon/radeon_device.c +++ b/drivers/gpu/drm/radeon/radeon_device.c @@ -450,6 +450,7 @@ int radeon_device_init(struct radeon_device *rdev, uint32_t flags) { int r, ret; + int dma_bits; DRM_INFO("radeon: Initializing kernel modesetting.\n"); rdev->shutdown = false; @@ -492,8 +493,20 @@ int radeon_device_init(struct radeon_device *rdev, return r; } - /* Report DMA addressing limitation */ - r = pci_set_dma_mask(rdev->pdev, DMA_BIT_MASK(32)); + /* set DMA mask + need_dma32 flags. + * PCIE - can handle 40-bits. + * IGP - can handle 40-bits (in theory) + * AGP - generally dma32 is safest + * PCI - only dma32 + */ + rdev->need_dma32 = false; + if (rdev->flags & RADEON_IS_AGP) + rdev->need_dma32 = true; + if (rdev->flags & RADEON_IS_PCI) + rdev->need_dma32 = true; + + dma_bits = rdev->need_dma32 ? 32 : 40; + r = pci_set_dma_mask(rdev->pdev, DMA_BIT_MASK(dma_bits)); if (r) { printk(KERN_WARNING "radeon: No suitable DMA available.\n"); } diff --git a/drivers/gpu/drm/radeon/radeon_ttm.c b/drivers/gpu/drm/radeon/radeon_ttm.c index 1227a97f516..4ca9aa9203d 100644 --- a/drivers/gpu/drm/radeon/radeon_ttm.c +++ b/drivers/gpu/drm/radeon/radeon_ttm.c @@ -442,7 +442,8 @@ int radeon_ttm_init(struct radeon_device *rdev) /* No others user of address space so set it to 0 */ r = ttm_bo_device_init(&rdev->mman.bdev, rdev->mman.mem_global_ref.object, - &radeon_bo_driver, DRM_FILE_PAGE_OFFSET); + &radeon_bo_driver, DRM_FILE_PAGE_OFFSET, + rdev->need_dma32); if (r) { DRM_ERROR("failed initializing buffer object driver(%d).\n", r); return r; diff --git a/drivers/gpu/drm/ttm/ttm_bo.c b/drivers/gpu/drm/ttm/ttm_bo.c index a753598a5e3..e55e7972c89 100644 --- a/drivers/gpu/drm/ttm/ttm_bo.c +++ b/drivers/gpu/drm/ttm/ttm_bo.c @@ -224,6 +224,9 @@ static int ttm_bo_add_ttm(struct ttm_buffer_object *bo, bool zero_alloc) TTM_ASSERT_LOCKED(&bo->mutex); bo->ttm = NULL; + if (bdev->need_dma32) + page_flags |= TTM_PAGE_FLAG_DMA32; + switch (bo->type) { case ttm_bo_type_device: if (zero_alloc) @@ -1332,7 +1335,8 @@ EXPORT_SYMBOL(ttm_bo_device_release); int ttm_bo_device_init(struct ttm_bo_device *bdev, struct ttm_mem_global *mem_glob, - struct ttm_bo_driver *driver, uint64_t file_page_offset) + struct ttm_bo_driver *driver, uint64_t file_page_offset, + bool need_dma32) { int ret = -EINVAL; @@ -1369,6 +1373,7 @@ int ttm_bo_device_init(struct ttm_bo_device *bdev, INIT_LIST_HEAD(&bdev->ddestroy); INIT_LIST_HEAD(&bdev->swap_lru); bdev->dev_mapping = NULL; + bdev->need_dma32 = need_dma32; ttm_mem_init_shrink(&bdev->shrink, ttm_bo_swapout); ret = ttm_mem_register_shrink(mem_glob, &bdev->shrink); if (unlikely(ret != 0)) { diff --git a/drivers/gpu/drm/ttm/ttm_tt.c b/drivers/gpu/drm/ttm/ttm_tt.c index 75dc8bd2459..81ab81f030a 100644 --- a/drivers/gpu/drm/ttm/ttm_tt.c +++ b/drivers/gpu/drm/ttm/ttm_tt.c @@ -131,10 +131,15 @@ static void ttm_tt_free_page_directory(struct ttm_tt *ttm) static struct page *ttm_tt_alloc_page(unsigned page_flags) { + gfp_t gfp_flags = GFP_HIGHUSER; + if (page_flags & TTM_PAGE_FLAG_ZERO_ALLOC) - return alloc_page(GFP_HIGHUSER | __GFP_ZERO); + gfp_flags |= __GFP_ZERO; + + if (page_flags & TTM_PAGE_FLAG_DMA32) + gfp_flags |= __GFP_DMA32; - return alloc_page(GFP_HIGHUSER); + return alloc_page(gfp_flags); } static void ttm_tt_free_user_pages(struct ttm_tt *ttm) diff --git a/include/drm/ttm/ttm_bo_driver.h b/include/drm/ttm/ttm_bo_driver.h index 62ed733c52a..ea83dd23a4d 100644 --- a/include/drm/ttm/ttm_bo_driver.h +++ b/include/drm/ttm/ttm_bo_driver.h @@ -121,6 +121,7 @@ struct ttm_backend { #define TTM_PAGE_FLAG_SWAPPED (1 << 4) #define TTM_PAGE_FLAG_PERSISTANT_SWAP (1 << 5) #define TTM_PAGE_FLAG_ZERO_ALLOC (1 << 6) +#define TTM_PAGE_FLAG_DMA32 (1 << 7) enum ttm_caching_state { tt_uncached, @@ -429,6 +430,8 @@ struct ttm_bo_device { */ struct delayed_work wq; + + bool need_dma32; }; /** @@ -648,7 +651,7 @@ extern int ttm_bo_device_release(struct ttm_bo_device *bdev); extern int ttm_bo_device_init(struct ttm_bo_device *bdev, struct ttm_mem_global *mem_glob, struct ttm_bo_driver *driver, - uint64_t file_page_offset); + uint64_t file_page_offset, bool need_dma32); /** * ttm_bo_reserve: -- GitLab From 2a0f8918fc34713ecaeb900ffb9afa61df4cb08e Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Sat, 11 Jul 2009 04:44:47 +1000 Subject: [PATCH 0054/1342] drm/radeon/kms: fix VRAM sizing like DDX does it. Doing this like the DDX seems like the most sure fire way to avoid having to reinvent it slowly and painfully. At the moment we keep getting things wrong with aper vs vram, so we know the DDX does it right. booted on PCI r100, PCIE rv370, IGP rs400. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 65 +++++++++++++++++++++++++- drivers/gpu/drm/radeon/r300.c | 4 +- drivers/gpu/drm/radeon/r520.c | 4 +- drivers/gpu/drm/radeon/radeon.h | 2 + drivers/gpu/drm/radeon/radeon_device.c | 7 +-- drivers/gpu/drm/radeon/rs400.c | 14 +----- drivers/gpu/drm/radeon/rv515.c | 6 +-- 7 files changed, 71 insertions(+), 31 deletions(-) diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index 154648a2c02..97c9229b929 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -1360,9 +1360,50 @@ static void r100_vram_get_type(struct radeon_device *rdev) } } -void r100_vram_info(struct radeon_device *rdev) +static u32 r100_get_accessible_vram(struct radeon_device *rdev) { - r100_vram_get_type(rdev); + u32 aper_size; + u8 byte; + + aper_size = RREG32(RADEON_CONFIG_APER_SIZE); + + /* Set HDP_APER_CNTL only on cards that are known not to be broken, + * that is has the 2nd generation multifunction PCI interface + */ + if (rdev->family == CHIP_RV280 || + rdev->family >= CHIP_RV350) { + WREG32_P(RADEON_HOST_PATH_CNTL, RADEON_HDP_APER_CNTL, + ~RADEON_HDP_APER_CNTL); + DRM_INFO("Generation 2 PCI interface, using max accessible memory\n"); + return aper_size * 2; + } + + /* Older cards have all sorts of funny issues to deal with. First + * check if it's a multifunction card by reading the PCI config + * header type... Limit those to one aperture size + */ + pci_read_config_byte(rdev->pdev, 0xe, &byte); + if (byte & 0x80) { + DRM_INFO("Generation 1 PCI interface in multifunction mode\n"); + DRM_INFO("Limiting VRAM to one aperture\n"); + return aper_size; + } + + /* Single function older card. We read HDP_APER_CNTL to see how the BIOS + * have set it up. We don't write this as it's broken on some ASICs but + * we expect the BIOS to have done the right thing (might be too optimistic...) + */ + if (RREG32(RADEON_HOST_PATH_CNTL) & RADEON_HDP_APER_CNTL) + return aper_size * 2; + return aper_size; +} + +void r100_vram_init_sizes(struct radeon_device *rdev) +{ + u64 config_aper_size; + u32 accessible; + + config_aper_size = RREG32(RADEON_CONFIG_APER_SIZE); if (rdev->flags & RADEON_IS_IGP) { uint32_t tom; @@ -1383,10 +1424,30 @@ void r100_vram_info(struct radeon_device *rdev) } /* let driver place VRAM */ rdev->mc.vram_location = 0xFFFFFFFFUL; + /* Fix for RN50, M6, M7 with 8/16/32(??) MBs of VRAM - + * Novell bug 204882 + along with lots of ubuntu ones */ + if (config_aper_size > rdev->mc.vram_size) + rdev->mc.vram_size = config_aper_size; } + /* work out accessible VRAM */ + accessible = r100_get_accessible_vram(rdev); + rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); + + if (accessible > rdev->mc.aper_size) + accessible = rdev->mc.aper_size; + + if (rdev->mc.vram_size > rdev->mc.aper_size) + rdev->mc.vram_size = rdev->mc.aper_size; +} + +void r100_vram_info(struct radeon_device *rdev) +{ + r100_vram_get_type(rdev); + + r100_vram_init_sizes(rdev); } diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c index 6435d659cbd..0e0e094da50 100644 --- a/drivers/gpu/drm/radeon/r300.c +++ b/drivers/gpu/drm/radeon/r300.c @@ -585,10 +585,8 @@ void r300_vram_info(struct radeon_device *rdev) } else { rdev->mc.vram_width = 64; } - rdev->mc.vram_size = RREG32(RADEON_CONFIG_MEMSIZE); - rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); - rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); + r100_vram_init_sizes(rdev); } diff --git a/drivers/gpu/drm/radeon/r520.c b/drivers/gpu/drm/radeon/r520.c index 570a244bd88..b6bd3758db6 100644 --- a/drivers/gpu/drm/radeon/r520.c +++ b/drivers/gpu/drm/radeon/r520.c @@ -227,8 +227,6 @@ static void r520_vram_get_type(struct radeon_device *rdev) void r520_vram_info(struct radeon_device *rdev) { r520_vram_get_type(rdev); - rdev->mc.vram_size = RREG32(RADEON_CONFIG_MEMSIZE); - rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); - rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); + r100_vram_init_sizes(rdev); } diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index 3060ce14071..248e3341a98 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -541,6 +541,8 @@ union radeon_asic_config { struct r300_asic r300; }; +/* r100 */ +void r100_vram_init_sizes(struct radeon_device *rdev); /* * IOCTL. diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c index 27a5ac96995..cdef6eb01ba 100644 --- a/drivers/gpu/drm/radeon/radeon_device.c +++ b/drivers/gpu/drm/radeon/radeon_device.c @@ -561,12 +561,7 @@ int radeon_device_init(struct radeon_device *rdev, } /* Get vram informations */ radeon_vram_info(rdev); - /* Device is severly broken if aper size > vram size. - * for RN50/M6/M7 - Novell bug 204882 ? - */ - if (rdev->mc.vram_size < rdev->mc.aper_size) { - rdev->mc.vram_size = rdev->mc.aper_size; - } + /* Add an MTRR for the VRAM */ rdev->mc.vram_mtrr = mtrr_add(rdev->mc.aper_base, rdev->mc.aper_size, MTRR_TYPE_WRCOMB, 1); diff --git a/drivers/gpu/drm/radeon/rs400.c b/drivers/gpu/drm/radeon/rs400.c index a18d053065c..daf24e85cba 100644 --- a/drivers/gpu/drm/radeon/rs400.c +++ b/drivers/gpu/drm/radeon/rs400.c @@ -292,24 +292,12 @@ void rs400_gpu_init(struct radeon_device *rdev) */ void rs400_vram_info(struct radeon_device *rdev) { - uint32_t tom; - rs400_gart_adjust_size(rdev); /* DDR for all card after R300 & IGP */ rdev->mc.vram_is_ddr = true; rdev->mc.vram_width = 128; - /* read NB_TOM to get the amount of ram stolen for the GPU */ - tom = RREG32(RADEON_NB_TOM); - rdev->mc.vram_size = (((tom >> 16) - (tom & 0xffff) + 1) << 16); - WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); - - /* RS480 IGPs don't seem to translate to main RAM, they - * just reserve and scan out of it. So setting VRAM location - * to say 0, will actually trash the OS. */ - rdev->mc.vram_location = (tom & 0xffff) << 16; - rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); - rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); + r100_vram_init_sizes(rdev); } diff --git a/drivers/gpu/drm/radeon/rv515.c b/drivers/gpu/drm/radeon/rv515.c index d1384d3991a..677929ed8ed 100644 --- a/drivers/gpu/drm/radeon/rv515.c +++ b/drivers/gpu/drm/radeon/rv515.c @@ -395,10 +395,8 @@ static void rv515_vram_get_type(struct radeon_device *rdev) void rv515_vram_info(struct radeon_device *rdev) { rv515_vram_get_type(rdev); - rdev->mc.vram_size = RREG32(RADEON_CONFIG_MEMSIZE); - - rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); - rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); + + r100_vram_init_sizes(rdev); } -- GitLab From b995e4330de0d8b1b8b9e49ce10cc6dc78e2cbba Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Tue, 14 Jul 2009 02:02:32 +1000 Subject: [PATCH 0055/1342] drm/radeon/kms: block RN50 from using 3D engine. RN50/ES1000 is a cut-down rv100 chip used in the server market. The 3D engine on these is either not there or unverified so refuse any attempt to configure registers on it. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 5 +++++ drivers/gpu/drm/radeon/radeon.h | 2 ++ 2 files changed, 7 insertions(+) diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index 97c9229b929..0d05909f03f 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -973,6 +973,11 @@ static int r100_packet0_check(struct radeon_cs_parser *p, case R300_TX_OFFSET_0+52: case R300_TX_OFFSET_0+56: case R300_TX_OFFSET_0+60: + /* rn50 has no 3D engine so fail on any 3d setup */ + if (ASIC_IS_RN50(p->rdev)) { + DRM_ERROR("attempt to use RN50 3D engine failed\n"); + return -EINVAL; + } r = r100_cs_packet_next_reloc(p, &reloc); if (r) { DRM_ERROR("No reloc for ib[%d]=0x%04X\n", diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index 248e3341a98..7f007185e7f 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -673,6 +673,8 @@ void r100_pll_errata_after_index(struct radeon_device *rdev); /* * ASICs helpers. */ +#define ASIC_IS_RN50(rdev) ((rdev->pdev->device == 0x515e) || \ + (rdev->pdev->device == 0x5969)) #define ASIC_IS_RV100(rdev) ((rdev->family == CHIP_RV100) || \ (rdev->family == CHIP_RV200) || \ (rdev->family == CHIP_RS100) || \ -- GitLab From d0e275a90a81b37409a0cfbca77581e3d235f5cf Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Mon, 13 Jul 2009 11:08:18 -0400 Subject: [PATCH 0056/1342] drm/radeon/kms: add PLL flag to prefer frequencies <= the target freq This is needed when using fractional feedback dividers on some IGP chips. Signed-off-by: Alex Deucher Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_display.c | 6 +++++- drivers/gpu/drm/radeon/radeon_mode.h | 1 + 2 files changed, 6 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/radeon/radeon_display.c b/drivers/gpu/drm/radeon/radeon_display.c index 3efcf1a526b..bc312f3d9a0 100644 --- a/drivers/gpu/drm/radeon/radeon_display.c +++ b/drivers/gpu/drm/radeon/radeon_display.c @@ -491,7 +491,11 @@ void radeon_compute_pll(struct radeon_pll *pll, tmp += (uint64_t)pll->reference_freq * 1000 * frac_feedback_div; current_freq = radeon_div(tmp, ref_div * post_div); - error = abs(current_freq - freq); + if (flags & RADEON_PLL_PREFER_CLOSEST_LOWER) { + error = freq - current_freq; + error = error < 0 ? 0xffffffff : error; + } else + error = abs(current_freq - freq); vco_diff = abs(vco - best_vco); if ((best_vco == 0 && error < best_error) || diff --git a/drivers/gpu/drm/radeon/radeon_mode.h b/drivers/gpu/drm/radeon/radeon_mode.h index 86f766e868e..38c1dd08244 100644 --- a/drivers/gpu/drm/radeon/radeon_mode.h +++ b/drivers/gpu/drm/radeon/radeon_mode.h @@ -124,6 +124,7 @@ struct radeon_tmds_pll { #define RADEON_PLL_PREFER_LOW_POST_DIV (1 << 8) #define RADEON_PLL_PREFER_HIGH_POST_DIV (1 << 9) #define RADEON_PLL_USE_FRAC_FB_DIV (1 << 10) +#define RADEON_PLL_PREFER_CLOSEST_LOWER (1 << 11) struct radeon_pll { uint16_t reference_freq; -- GitLab From eb1300bcd70b3bffbefb6ae0eab13a571255ee93 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Mon, 13 Jul 2009 11:09:56 -0400 Subject: [PATCH 0057/1342] drm/radeon/kms: enable frac fb divs on rs600/rs690/rs740 Allows us to hit dot clocks much closer, especially on chips with non-27 Mhz reference clocks like most IGP chips. This fixes most flickering and blanking problems with non-exact dot clocks on these chips. Signed-off-by: Alex Deucher Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/atombios_crtc.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/gpu/drm/radeon/atombios_crtc.c b/drivers/gpu/drm/radeon/atombios_crtc.c index c0080cc9bf8..e64a199b5ee 100644 --- a/drivers/gpu/drm/radeon/atombios_crtc.c +++ b/drivers/gpu/drm/radeon/atombios_crtc.c @@ -203,6 +203,12 @@ void atombios_crtc_set_pll(struct drm_crtc *crtc, struct drm_display_mode *mode) if (ASIC_IS_AVIVO(rdev)) { uint32_t ss_cntl; + if ((rdev->family == CHIP_RS600) || + (rdev->family == CHIP_RS690) || + (rdev->family == CHIP_RS740)) + pll_flags |= (RADEON_PLL_USE_FRAC_FB_DIV | + RADEON_PLL_PREFER_CLOSEST_LOWER); + if (ASIC_IS_DCE32(rdev) && mode->clock > 200000) /* range limits??? */ pll_flags |= RADEON_PLL_PREFER_HIGH_FB_DIV; else -- GitLab From c836e862803b2aa2bd9a354e151316d2b42c44ec Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Mon, 13 Jul 2009 13:51:03 -0400 Subject: [PATCH 0058/1342] drm/radeon/kms: fix hotspot handling on pre-avivo chips Need to adjust CUR_OFFSET for yorigin Signed-off-by: Alex Deucher Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_cursor.c | 9 +++++++-- drivers/gpu/drm/radeon/radeon_mode.h | 1 + 2 files changed, 8 insertions(+), 2 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon_cursor.c b/drivers/gpu/drm/radeon/radeon_cursor.c index 5f8ce370c4f..b13c79e38bc 100644 --- a/drivers/gpu/drm/radeon/radeon_cursor.c +++ b/drivers/gpu/drm/radeon/radeon_cursor.c @@ -111,9 +111,11 @@ static void radeon_set_cursor(struct drm_crtc *crtc, struct drm_gem_object *obj, if (ASIC_IS_AVIVO(rdev)) WREG32(AVIVO_D1CUR_SURFACE_ADDRESS + radeon_crtc->crtc_offset, gpu_addr); - else + else { + radeon_crtc->legacy_cursor_offset = gpu_addr - radeon_crtc->legacy_display_base_addr; /* offset is from DISP(2)_BASE_ADDRESS */ - WREG32(RADEON_CUR_OFFSET + radeon_crtc->crtc_offset, (gpu_addr-radeon_crtc->legacy_display_base_addr)); + WREG32(RADEON_CUR_OFFSET + radeon_crtc->crtc_offset, radeon_crtc->legacy_cursor_offset); + } } int radeon_crtc_cursor_set(struct drm_crtc *crtc, @@ -245,6 +247,9 @@ int radeon_crtc_cursor_move(struct drm_crtc *crtc, (RADEON_CUR_LOCK | ((xorigin ? 0 : x) << 16) | (yorigin ? 0 : y))); + /* offset is from DISP(2)_BASE_ADDRESS */ + WREG32(RADEON_CUR_OFFSET + radeon_crtc->crtc_offset, (radeon_crtc->legacy_cursor_offset + + (yorigin * 256))); } radeon_lock_cursor(crtc, false); diff --git a/drivers/gpu/drm/radeon/radeon_mode.h b/drivers/gpu/drm/radeon/radeon_mode.h index 38c1dd08244..ba89b59f6e5 100644 --- a/drivers/gpu/drm/radeon/radeon_mode.h +++ b/drivers/gpu/drm/radeon/radeon_mode.h @@ -187,6 +187,7 @@ struct radeon_crtc { int cursor_width; int cursor_height; uint32_t legacy_display_base_addr; + uint32_t legacy_cursor_offset; }; #define RADEON_USE_RMX 1 -- GitLab From c8cc452501572d4a81331179b00a9bdd5d2bfada Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Fri, 10 Jul 2009 16:59:36 +0300 Subject: [PATCH 0059/1342] UBI: gluebi: initialize ubi_num field Do not forget to initialize 'gluebi->ubi_num' because otherwise it will stay 0 even for ubi1 device, and gluebi will open wrong UBI device when 'gluebi_get_device()' is called. Signed-off-by: Artem Bityutskiy --- drivers/mtd/ubi/gluebi.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/mtd/ubi/gluebi.c b/drivers/mtd/ubi/gluebi.c index 95aaac03f93..b5e478fa266 100644 --- a/drivers/mtd/ubi/gluebi.c +++ b/drivers/mtd/ubi/gluebi.c @@ -332,6 +332,7 @@ static int gluebi_create(struct ubi_device_info *di, } gluebi->vol_id = vi->vol_id; + gluebi->ubi_num = vi->ubi_num; mtd->type = MTD_UBIVOLUME; if (!di->ro_mode) mtd->flags = MTD_WRITEABLE; -- GitLab From 3dc948da783e713cd3dc8bbd8f293f8795af8f06 Mon Sep 17 00:00:00 2001 From: Holger Brunck Date: Mon, 13 Jul 2009 16:47:57 +0200 Subject: [PATCH 0060/1342] UBI: fix bug in image sequence number handling This patch fixes a bug in the image seq. number handling in the scanning level. The assignment of the image_seq was incorrect. Signed-off-by: Holger Brunck Signed-off-by: Artem Bityutskiy --- drivers/mtd/ubi/scan.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/mtd/ubi/scan.c b/drivers/mtd/ubi/scan.c index f60895ee0ae..a423131b617 100644 --- a/drivers/mtd/ubi/scan.c +++ b/drivers/mtd/ubi/scan.c @@ -781,7 +781,7 @@ static int process_eb(struct ubi_device *ubi, struct ubi_scan_info *si, return -EINVAL; } - image_seq = be32_to_cpu(ech->ec); + image_seq = be32_to_cpu(ech->image_seq); if (!si->image_seq_set) { ubi->image_seq = image_seq; si->image_seq_set = 1; -- GitLab From f7e5cc0c40dff92bad2894153f675c6c542ba2f0 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Lothar=20Wa=C3=9Fmann?= Date: Tue, 14 Jul 2009 23:10:21 +0000 Subject: [PATCH 0061/1342] net/can bugfix: use after free bug in can protocol drivers Fix a use after free bug in can protocol drivers The release functions of the can protocol drivers lack a call to sock_orphan() which leads to referencing freed memory under certain circumstances. This patch fixes a bug reported here: https://lists.berlios.de/pipermail/socketcan-users/2009-July/000985.html Signed-off-by: Lothar Wassmann Acked-by: Oliver Hartkopp Signed-off-by: David S. Miller --- net/can/bcm.c | 3 +++ net/can/raw.c | 3 +++ 2 files changed, 6 insertions(+) diff --git a/net/can/bcm.c b/net/can/bcm.c index 95d7f32643a..1d17e41b892 100644 --- a/net/can/bcm.c +++ b/net/can/bcm.c @@ -1469,6 +1469,9 @@ static int bcm_release(struct socket *sock) bo->ifindex = 0; } + sock_orphan(sk); + sock->sk = NULL; + release_sock(sk); sock_put(sk); diff --git a/net/can/raw.c b/net/can/raw.c index 6aa154e806a..3482546e888 100644 --- a/net/can/raw.c +++ b/net/can/raw.c @@ -306,6 +306,9 @@ static int raw_release(struct socket *sock) ro->bound = 0; ro->count = 0; + sock_orphan(sk); + sock->sk = NULL; + release_sock(sk); sock_put(sk); -- GitLab From b13bb2e9933b9dfa25c81d959d847c843481111e Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Lothar=20Wa=C3=9Fmann?= Date: Tue, 14 Jul 2009 23:12:25 +0000 Subject: [PATCH 0062/1342] net/can: add module alias to can protocol drivers Add appropriate MODULE_ALIAS() to facilitate autoloading of can protocol drivers Signed-off-by: Lothar Wassmann Acked-by: Oliver Hartkopp Signed-off-by: David S. Miller --- net/can/bcm.c | 1 + net/can/raw.c | 1 + 2 files changed, 2 insertions(+) diff --git a/net/can/bcm.c b/net/can/bcm.c index 1d17e41b892..72720c71035 100644 --- a/net/can/bcm.c +++ b/net/can/bcm.c @@ -75,6 +75,7 @@ static __initdata const char banner[] = KERN_INFO MODULE_DESCRIPTION("PF_CAN broadcast manager protocol"); MODULE_LICENSE("Dual BSD/GPL"); MODULE_AUTHOR("Oliver Hartkopp "); +MODULE_ALIAS("can-proto-2"); /* easy access to can_frame payload */ static inline u64 GET_U64(const struct can_frame *cp) diff --git a/net/can/raw.c b/net/can/raw.c index 3482546e888..f4cc44548bd 100644 --- a/net/can/raw.c +++ b/net/can/raw.c @@ -62,6 +62,7 @@ static __initdata const char banner[] = MODULE_DESCRIPTION("PF_CAN raw protocol"); MODULE_LICENSE("Dual BSD/GPL"); MODULE_AUTHOR("Urs Thuermann "); +MODULE_ALIAS("can-proto-1"); #define MASK_ALL 0 -- GitLab From 7447a668a3860b66b3c9db86fdea91e355ba59ac Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Wed, 15 Jul 2009 20:36:08 +0200 Subject: [PATCH 0063/1342] jbd: Fail to load a journal if it is too short Due to on disk corruption, it can happen that journal is too short. Fail to load it in such case so that we don't oops somewhere later. Reported-by: Nageswara R Sastry Signed-off-by: Jan Kara --- fs/jbd/journal.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/fs/jbd/journal.c b/fs/jbd/journal.c index 737f7246a4b..94a64a199a6 100644 --- a/fs/jbd/journal.c +++ b/fs/jbd/journal.c @@ -848,6 +848,12 @@ static int journal_reset(journal_t *journal) first = be32_to_cpu(sb->s_first); last = be32_to_cpu(sb->s_maxlen); + if (first + JFS_MIN_JOURNAL_BLOCKS > last + 1) { + printk(KERN_ERR "JBD: Journal too short (blocks %lu-%lu).\n", + first, last); + journal_fail_superblock(journal); + return -EINVAL; + } journal->j_first = first; journal->j_last = last; -- GitLab From 9eaaa2d5759837402ec5eee13b2a97921808c3eb Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Mon, 13 Jul 2009 20:26:52 +0200 Subject: [PATCH 0064/1342] ext3: Fix truncation of symlinks after failed write Contents of long symlinks is written via standard write methods. So when the write fails, we add inode to orphan list. But symlinks don't have .truncate method defined so nobody properly removes them from the orphan list (both on disk and in memory). Fix this by calling ext3_truncate() directly instead of calling vmtruncate() (which is saner anyway since we don't need anything vmtruncate() does except from calling .truncate in these paths). We also add inode to orphan list only if ext3_can_truncate() is true (currently, it can be false for symlinks when there are no blocks allocated) - otherwise orphan list processing will complain and ext3_truncate() will not remove inode from on-disk orphan list. Signed-off-by: Jan Kara --- fs/ext3/inode.c | 19 ++++++++++--------- 1 file changed, 10 insertions(+), 9 deletions(-) diff --git a/fs/ext3/inode.c b/fs/ext3/inode.c index 5f51fed5c75..4d7da6f6184 100644 --- a/fs/ext3/inode.c +++ b/fs/ext3/inode.c @@ -1193,15 +1193,16 @@ write_begin_failed: * i_size_read because we hold i_mutex. * * Add inode to orphan list in case we crash before truncate - * finishes. + * finishes. Do this only if ext3_can_truncate() agrees so + * that orphan processing code is happy. */ - if (pos + len > inode->i_size) + if (pos + len > inode->i_size && ext3_can_truncate(inode)) ext3_orphan_add(handle, inode); ext3_journal_stop(handle); unlock_page(page); page_cache_release(page); if (pos + len > inode->i_size) - vmtruncate(inode, inode->i_size); + ext3_truncate(inode); } if (ret == -ENOSPC && ext3_should_retry_alloc(inode->i_sb, &retries)) goto retry; @@ -1287,7 +1288,7 @@ static int ext3_ordered_write_end(struct file *file, * There may be allocated blocks outside of i_size because * we failed to copy some data. Prepare for truncate. */ - if (pos + len > inode->i_size) + if (pos + len > inode->i_size && ext3_can_truncate(inode)) ext3_orphan_add(handle, inode); ret2 = ext3_journal_stop(handle); if (!ret) @@ -1296,7 +1297,7 @@ static int ext3_ordered_write_end(struct file *file, page_cache_release(page); if (pos + len > inode->i_size) - vmtruncate(inode, inode->i_size); + ext3_truncate(inode); return ret ? ret : copied; } @@ -1315,14 +1316,14 @@ static int ext3_writeback_write_end(struct file *file, * There may be allocated blocks outside of i_size because * we failed to copy some data. Prepare for truncate. */ - if (pos + len > inode->i_size) + if (pos + len > inode->i_size && ext3_can_truncate(inode)) ext3_orphan_add(handle, inode); ret = ext3_journal_stop(handle); unlock_page(page); page_cache_release(page); if (pos + len > inode->i_size) - vmtruncate(inode, inode->i_size); + ext3_truncate(inode); return ret ? ret : copied; } @@ -1358,7 +1359,7 @@ static int ext3_journalled_write_end(struct file *file, * There may be allocated blocks outside of i_size because * we failed to copy some data. Prepare for truncate. */ - if (pos + len > inode->i_size) + if (pos + len > inode->i_size && ext3_can_truncate(inode)) ext3_orphan_add(handle, inode); EXT3_I(inode)->i_state |= EXT3_STATE_JDATA; if (inode->i_size > EXT3_I(inode)->i_disksize) { @@ -1375,7 +1376,7 @@ static int ext3_journalled_write_end(struct file *file, page_cache_release(page); if (pos + len > inode->i_size) - vmtruncate(inode, inode->i_size); + ext3_truncate(inode); return ret ? ret : copied; } -- GitLab From 1e9fd53b783ea646de3ee09a4574afeb6778d504 Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Wed, 24 Jun 2009 17:31:40 +0200 Subject: [PATCH 0065/1342] jbd: Fix a race between checkpointing code and journal_get_write_access() The following race can happen: CPU1 CPU2 checkpointing code checks the buffer, adds it to an array for writeback do_get_write_access() ... lock_buffer() unlock_buffer() flush_batch() submits the buffer for IO __jbd_journal_file_buffer() So a buffer under writeout is returned from do_get_write_access(). Since the filesystem code relies on the fact that journaled buffers cannot be written out, it does not take the buffer lock and so it can modify buffer while it is under writeout. That can lead to a filesystem corruption if we crash at the right moment. The similar problem can happen with the journal_get_create_access() path. We fix the problem by clearing the buffer dirty bit under buffer_lock even if the buffer is on BJ_None list. Actually, we clear the dirty bit regardless the list the buffer is in and warn about the fact if the buffer is already journalled. Thanks for spotting the problem goes to dingdinghua . Reported-by: dingdinghua Signed-off-by: Jan Kara --- fs/jbd/transaction.c | 68 +++++++++++++++++++++++--------------------- 1 file changed, 35 insertions(+), 33 deletions(-) diff --git a/fs/jbd/transaction.c b/fs/jbd/transaction.c index 73242ba7c7b..c03ac11f74b 100644 --- a/fs/jbd/transaction.c +++ b/fs/jbd/transaction.c @@ -489,34 +489,15 @@ void journal_unlock_updates (journal_t *journal) wake_up(&journal->j_wait_transaction_locked); } -/* - * Report any unexpected dirty buffers which turn up. Normally those - * indicate an error, but they can occur if the user is running (say) - * tune2fs to modify the live filesystem, so we need the option of - * continuing as gracefully as possible. # - * - * The caller should already hold the journal lock and - * j_list_lock spinlock: most callers will need those anyway - * in order to probe the buffer's journaling state safely. - */ -static void jbd_unexpected_dirty_buffer(struct journal_head *jh) +static void warn_dirty_buffer(struct buffer_head *bh) { - int jlist; - - /* If this buffer is one which might reasonably be dirty - * --- ie. data, or not part of this journal --- then - * we're OK to leave it alone, but otherwise we need to - * move the dirty bit to the journal's own internal - * JBDDirty bit. */ - jlist = jh->b_jlist; + char b[BDEVNAME_SIZE]; - if (jlist == BJ_Metadata || jlist == BJ_Reserved || - jlist == BJ_Shadow || jlist == BJ_Forget) { - struct buffer_head *bh = jh2bh(jh); - - if (test_clear_buffer_dirty(bh)) - set_buffer_jbddirty(bh); - } + printk(KERN_WARNING + "JBD: Spotted dirty metadata buffer (dev = %s, blocknr = %llu). " + "There's a risk of filesystem corruption in case of system " + "crash.\n", + bdevname(bh->b_bdev, b), (unsigned long long)bh->b_blocknr); } /* @@ -583,14 +564,16 @@ repeat: if (jh->b_next_transaction) J_ASSERT_JH(jh, jh->b_next_transaction == transaction); + warn_dirty_buffer(bh); } /* * In any case we need to clean the dirty flag and we must * do it under the buffer lock to be sure we don't race * with running write-out. */ - JBUFFER_TRACE(jh, "Unexpected dirty buffer"); - jbd_unexpected_dirty_buffer(jh); + JBUFFER_TRACE(jh, "Journalling dirty buffer"); + clear_buffer_dirty(bh); + set_buffer_jbddirty(bh); } unlock_buffer(bh); @@ -826,6 +809,15 @@ int journal_get_create_access(handle_t *handle, struct buffer_head *bh) J_ASSERT_JH(jh, buffer_locked(jh2bh(jh))); if (jh->b_transaction == NULL) { + /* + * Previous journal_forget() could have left the buffer + * with jbddirty bit set because it was being committed. When + * the commit finished, we've filed the buffer for + * checkpointing and marked it dirty. Now we are reallocating + * the buffer so the transaction freeing it must have + * committed and so it's safe to clear the dirty bit. + */ + clear_buffer_dirty(jh2bh(jh)); jh->b_transaction = transaction; /* first access by this transaction */ @@ -1782,8 +1774,13 @@ static int __dispose_buffer(struct journal_head *jh, transaction_t *transaction) if (jh->b_cp_transaction) { JBUFFER_TRACE(jh, "on running+cp transaction"); + /* + * We don't want to write the buffer anymore, clear the + * bit so that we don't confuse checks in + * __journal_file_buffer + */ + clear_buffer_dirty(bh); __journal_file_buffer(jh, transaction, BJ_Forget); - clear_buffer_jbddirty(bh); may_free = 0; } else { JBUFFER_TRACE(jh, "on running transaction"); @@ -2041,12 +2038,17 @@ void __journal_file_buffer(struct journal_head *jh, if (jh->b_transaction && jh->b_jlist == jlist) return; - /* The following list of buffer states needs to be consistent - * with __jbd_unexpected_dirty_buffer()'s handling of dirty - * state. */ - if (jlist == BJ_Metadata || jlist == BJ_Reserved || jlist == BJ_Shadow || jlist == BJ_Forget) { + /* + * For metadata buffers, we track dirty bit in buffer_jbddirty + * instead of buffer_dirty. We should not see a dirty bit set + * here because we clear it in do_get_write_access but e.g. + * tune2fs can modify the sb and set the dirty bit at any time + * so we try to gracefully handle that. + */ + if (buffer_dirty(bh)) + warn_dirty_buffer(bh); if (test_clear_buffer_dirty(bh) || test_clear_buffer_jbddirty(bh)) was_dirty = 1; -- GitLab From 43237b5490e8f2f4679decd660064ff35ce490cc Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Wed, 20 May 2009 18:41:58 +0200 Subject: [PATCH 0066/1342] ext3: Get rid of extenddisksize parameter of ext3_get_blocks_handle() Get rid of extenddisksize parameter of ext3_get_blocks_handle(). This seems to be a relict from some old days and setting disksize in this function does not make much sence. Currently it was set only by ext3_getblk(). Since the parameter has some effect only if create == 1, it is easy to check that the three callers which end up calling ext3_getblk() with create == 1 (ext3_append, ext3_quota_write, ext3_mkdir) do the right thing and set disksize themselves. Signed-off-by: Jan Kara --- fs/ext3/dir.c | 3 +-- fs/ext3/inode.c | 13 +++---------- include/linux/ext3_fs.h | 2 +- 3 files changed, 5 insertions(+), 13 deletions(-) diff --git a/fs/ext3/dir.c b/fs/ext3/dir.c index 3d724a95882..373fa90c796 100644 --- a/fs/ext3/dir.c +++ b/fs/ext3/dir.c @@ -130,8 +130,7 @@ static int ext3_readdir(struct file * filp, struct buffer_head *bh = NULL; map_bh.b_state = 0; - err = ext3_get_blocks_handle(NULL, inode, blk, 1, - &map_bh, 0, 0); + err = ext3_get_blocks_handle(NULL, inode, blk, 1, &map_bh, 0); if (err > 0) { pgoff_t index = map_bh.b_blocknr >> (PAGE_CACHE_SHIFT - inode->i_blkbits); diff --git a/fs/ext3/inode.c b/fs/ext3/inode.c index 4d7da6f6184..b49908a167a 100644 --- a/fs/ext3/inode.c +++ b/fs/ext3/inode.c @@ -788,7 +788,7 @@ err_out: int ext3_get_blocks_handle(handle_t *handle, struct inode *inode, sector_t iblock, unsigned long maxblocks, struct buffer_head *bh_result, - int create, int extend_disksize) + int create) { int err = -EIO; int offsets[4]; @@ -911,13 +911,6 @@ int ext3_get_blocks_handle(handle_t *handle, struct inode *inode, if (!err) err = ext3_splice_branch(handle, inode, iblock, partial, indirect_blks, count); - /* - * i_disksize growing is protected by truncate_mutex. Don't forget to - * protect it if you're about to implement concurrent - * ext3_get_block() -bzzz - */ - if (!err && extend_disksize && inode->i_size > ei->i_disksize) - ei->i_disksize = inode->i_size; mutex_unlock(&ei->truncate_mutex); if (err) goto cleanup; @@ -972,7 +965,7 @@ static int ext3_get_block(struct inode *inode, sector_t iblock, } ret = ext3_get_blocks_handle(handle, inode, iblock, - max_blocks, bh_result, create, 0); + max_blocks, bh_result, create); if (ret > 0) { bh_result->b_size = (ret << inode->i_blkbits); ret = 0; @@ -1005,7 +998,7 @@ struct buffer_head *ext3_getblk(handle_t *handle, struct inode *inode, dummy.b_blocknr = -1000; buffer_trace_init(&dummy.b_history); err = ext3_get_blocks_handle(handle, inode, block, 1, - &dummy, create, 1); + &dummy, create); /* * ext3_get_blocks_handle() returns number of blocks * mapped. 0 in case of a HOLE. diff --git a/include/linux/ext3_fs.h b/include/linux/ext3_fs.h index 634a5e5aba3..7499b366779 100644 --- a/include/linux/ext3_fs.h +++ b/include/linux/ext3_fs.h @@ -874,7 +874,7 @@ struct buffer_head * ext3_getblk (handle_t *, struct inode *, long, int, int *); struct buffer_head * ext3_bread (handle_t *, struct inode *, int, int, int *); int ext3_get_blocks_handle(handle_t *handle, struct inode *inode, sector_t iblock, unsigned long maxblocks, struct buffer_head *bh_result, - int create, int extend_disksize); + int create); extern struct inode *ext3_iget(struct super_block *, unsigned long); extern int ext3_write_inode (struct inode *, int); -- GitLab From aa6a03eb0ae859c1371555ef381de4c96ca1e4e6 Mon Sep 17 00:00:00 2001 From: Patrick McHardy Date: Thu, 16 Jul 2009 14:01:54 +0200 Subject: [PATCH 0067/1342] netfilter: xt_osf: fix nf_log_packet() arguments The first argument is the address family, the second one the hook number. Signed-off-by: Patrick McHardy --- net/netfilter/xt_osf.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/net/netfilter/xt_osf.c b/net/netfilter/xt_osf.c index 863e40977a4..0f482e2440b 100644 --- a/net/netfilter/xt_osf.c +++ b/net/netfilter/xt_osf.c @@ -330,7 +330,8 @@ static bool xt_osf_match_packet(const struct sk_buff *skb, fcount++; if (info->flags & XT_OSF_LOG) - nf_log_packet(p->hooknum, 0, skb, p->in, p->out, NULL, + nf_log_packet(p->family, p->hooknum, skb, + p->in, p->out, NULL, "%s [%s:%s] : %pi4:%d -> %pi4:%d hops=%d\n", f->genre, f->version, f->subtype, &ip->saddr, ntohs(tcp->source), @@ -345,7 +346,7 @@ static bool xt_osf_match_packet(const struct sk_buff *skb, rcu_read_unlock(); if (!fcount && (info->flags & XT_OSF_LOG)) - nf_log_packet(p->hooknum, 0, skb, p->in, p->out, NULL, + nf_log_packet(p->family, p->hooknum, skb, p->in, p->out, NULL, "Remote OS is not known: %pi4:%u -> %pi4:%u\n", &ip->saddr, ntohs(tcp->source), &ip->daddr, ntohs(tcp->dest)); -- GitLab From 941297f443f871b8c3372feccf27a8733f6ce9e9 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Thu, 16 Jul 2009 14:03:40 +0200 Subject: [PATCH 0068/1342] netfilter: nf_conntrack: nf_conntrack_alloc() fixes When a slab cache uses SLAB_DESTROY_BY_RCU, we must be careful when allocating objects, since slab allocator could give a freed object still used by lockless readers. In particular, nf_conntrack RCU lookups rely on ct->tuplehash[xxx].hnnode.next being always valid (ie containing a valid 'nulls' value, or a valid pointer to next object in hash chain.) kmem_cache_zalloc() setups object with NULL values, but a NULL value is not valid for ct->tuplehash[xxx].hnnode.next. Fix is to call kmem_cache_alloc() and do the zeroing ourself. As spotted by Patrick, we also need to make sure lookup keys are committed to memory before setting refcount to 1, or a lockless reader could get a reference on the old version of the object. Its key re-check could then pass the barrier. Signed-off-by: Eric Dumazet Signed-off-by: Patrick McHardy --- Documentation/RCU/rculist_nulls.txt | 7 ++++++- net/netfilter/nf_conntrack_core.c | 21 ++++++++++++++++++--- 2 files changed, 24 insertions(+), 4 deletions(-) diff --git a/Documentation/RCU/rculist_nulls.txt b/Documentation/RCU/rculist_nulls.txt index 93cb28d05dc..18f9651ff23 100644 --- a/Documentation/RCU/rculist_nulls.txt +++ b/Documentation/RCU/rculist_nulls.txt @@ -83,11 +83,12 @@ not detect it missed following items in original chain. obj = kmem_cache_alloc(...); lock_chain(); // typically a spin_lock() obj->key = key; -atomic_inc(&obj->refcnt); /* * we need to make sure obj->key is updated before obj->next + * or obj->refcnt */ smp_wmb(); +atomic_set(&obj->refcnt, 1); hlist_add_head_rcu(&obj->obj_node, list); unlock_chain(); // typically a spin_unlock() @@ -159,6 +160,10 @@ out: obj = kmem_cache_alloc(cachep); lock_chain(); // typically a spin_lock() obj->key = key; +/* + * changes to obj->key must be visible before refcnt one + */ +smp_wmb(); atomic_set(&obj->refcnt, 1); /* * insert obj in RCU way (readers might be traversing chain) diff --git a/net/netfilter/nf_conntrack_core.c b/net/netfilter/nf_conntrack_core.c index 7508f11c5b3..b5869b9574b 100644 --- a/net/netfilter/nf_conntrack_core.c +++ b/net/netfilter/nf_conntrack_core.c @@ -561,23 +561,38 @@ struct nf_conn *nf_conntrack_alloc(struct net *net, } } - ct = kmem_cache_zalloc(nf_conntrack_cachep, gfp); + /* + * Do not use kmem_cache_zalloc(), as this cache uses + * SLAB_DESTROY_BY_RCU. + */ + ct = kmem_cache_alloc(nf_conntrack_cachep, gfp); if (ct == NULL) { pr_debug("nf_conntrack_alloc: Can't alloc conntrack.\n"); atomic_dec(&net->ct.count); return ERR_PTR(-ENOMEM); } - + /* + * Let ct->tuplehash[IP_CT_DIR_ORIGINAL].hnnode.next + * and ct->tuplehash[IP_CT_DIR_REPLY].hnnode.next unchanged. + */ + memset(&ct->tuplehash[IP_CT_DIR_MAX], 0, + sizeof(*ct) - offsetof(struct nf_conn, tuplehash[IP_CT_DIR_MAX])); spin_lock_init(&ct->lock); - atomic_set(&ct->ct_general.use, 1); ct->tuplehash[IP_CT_DIR_ORIGINAL].tuple = *orig; + ct->tuplehash[IP_CT_DIR_ORIGINAL].hnnode.pprev = NULL; ct->tuplehash[IP_CT_DIR_REPLY].tuple = *repl; + ct->tuplehash[IP_CT_DIR_REPLY].hnnode.pprev = NULL; /* Don't set timer yet: wait for confirmation */ setup_timer(&ct->timeout, death_by_timeout, (unsigned long)ct); #ifdef CONFIG_NET_NS ct->ct_net = net; #endif + /* + * changes to lookup keys must be done before setting refcnt to 1 + */ + smp_wmb(); + atomic_set(&ct->ct_general.use, 1); return ct; } EXPORT_SYMBOL_GPL(nf_conntrack_alloc); -- GitLab From 5381837f125cc62ad703fbcdfcd7566fc81fd404 Mon Sep 17 00:00:00 2001 From: Tom Peng Date: Wed, 1 Jul 2009 20:37:26 +0800 Subject: [PATCH 0069/1342] [SCSI] libsas: reuse the original port when hotplugging phys in wide ports There's a hotplug problem in the way libsas allocates ports: it loops over the available ports first trying to add to an existing for a wide port and otherwise allocating the next free port. This scheme only works if the port array is packed from zero, which fails if a port gets hot unplugged and the array becomes sparse. In that case, a new port is formed even if there's a wide port it should be part of. Fix this by creating two loops over all the ports: the first to see if the phy should be part of a wide port and the second to form a new port in an empty port slot. Signed-off-by: Tom Peng Signed-off-by: Jack Wang Signed-off-by: Lindar Liu Cc: Stable Tree Signed-off-by: James Bottomley --- drivers/scsi/libsas/sas_port.c | 19 +++++++++++++++---- 1 file changed, 15 insertions(+), 4 deletions(-) diff --git a/drivers/scsi/libsas/sas_port.c b/drivers/scsi/libsas/sas_port.c index e6ac59c023f..fe8b74c706d 100644 --- a/drivers/scsi/libsas/sas_port.c +++ b/drivers/scsi/libsas/sas_port.c @@ -56,7 +56,7 @@ static void sas_form_port(struct asd_sas_phy *phy) } } - /* find a port */ + /* see if the phy should be part of a wide port */ spin_lock_irqsave(&sas_ha->phy_port_lock, flags); for (i = 0; i < sas_ha->num_phys; i++) { port = sas_ha->sas_port[i]; @@ -69,12 +69,23 @@ static void sas_form_port(struct asd_sas_phy *phy) SAS_DPRINTK("phy%d matched wide port%d\n", phy->id, port->id); break; - } else if (*(u64 *) port->sas_addr == 0 && port->num_phys==0) { - memcpy(port->sas_addr, phy->sas_addr, SAS_ADDR_SIZE); - break; } spin_unlock(&port->phy_list_lock); } + /* The phy does not match any existing port, create a new one */ + if (i == sas_ha->num_phys) { + for (i = 0; i < sas_ha->num_phys; i++) { + port = sas_ha->sas_port[i]; + spin_lock(&port->phy_list_lock); + if (*(u64 *)port->sas_addr == 0 + && port->num_phys == 0) { + memcpy(port->sas_addr, phy->sas_addr, + SAS_ADDR_SIZE); + break; + } + spin_unlock(&port->phy_list_lock); + } + } if (i >= sas_ha->num_phys) { printk(KERN_NOTICE "%s: couldn't find a free port, bug?\n", -- GitLab From 390c4dd448b1a5f04ea497c20f5ff664f8eeed01 Mon Sep 17 00:00:00 2001 From: Jesse Barnes Date: Thu, 16 Jul 2009 13:01:01 -0700 Subject: [PATCH 0070/1342] drm/i915: handle FIFO oversubsription correctly If you're pushing a plane hard (i.e. you need most or all of the FIFO entries just to cover your frame refresh latency), the watermark level may end up being negative. So fix up the signed vs. unsigned math in the calculation function to handle this correctly, giving all available FIFO entries to such a configuration. Reported-by: Eric Anholt Tested-by: Eric Anholt Signed-off-by: Jesse Barnes Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_display.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 3fa0d63c83b..890f7108e72 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -1674,7 +1674,7 @@ static unsigned long intel_calculate_wm(unsigned long clock_in_khz, int pixel_size, unsigned long latency_ns) { - unsigned long entries_required, wm_size; + long entries_required, wm_size; entries_required = (clock_in_khz * pixel_size * latency_ns) / 1000000; entries_required /= wm->cacheline_size; @@ -1685,9 +1685,10 @@ static unsigned long intel_calculate_wm(unsigned long clock_in_khz, DRM_DEBUG("FIFO watermark level: %d\n", wm_size); - if (wm_size > wm->max_wm) + /* Don't promote wm_size to unsigned... */ + if (wm_size > (long)wm->max_wm) wm_size = wm->max_wm; - if (wm_size == 0) + if (wm_size <= 0) wm_size = wm->default_wm; return wm_size; } -- GitLab From 2a2430f4542467502d39660bfd66b0004fd8d6a9 Mon Sep 17 00:00:00 2001 From: Jesse Barnes Date: Thu, 16 Jul 2009 13:01:02 -0700 Subject: [PATCH 0071/1342] drm/i915: correct self-refresh calculation in "everything off" case If no planes are enabled, the self-refresh calculation may end up doing a divide by zero. This patch should prevent that by making sure at least one of the CRTCs had a valid hdisplay value. Reported-by: Eric Anholt Tested-by: Eric Anholt Signed-off-by: Jesse Barnes Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_display.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 890f7108e72..a58bfadabd6 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -1906,7 +1906,7 @@ static void i9xx_update_wm(struct drm_device *dev, int planea_clock, cwm = 2; /* Calc sr entries for one plane configs */ - if (!planea_clock || !planeb_clock) { + if (sr_hdisplay && (!planea_clock || !planeb_clock)) { /* self-refresh has much higher latency */ const static int sr_latency_ns = 6000; @@ -1921,6 +1921,8 @@ static void i9xx_update_wm(struct drm_device *dev, int planea_clock, srwm = total_size - sr_entries; if (srwm < 0) srwm = 1; + if (IS_I9XX(dev)) + I915_WRITE(FW_BLC_SELF, (srwm & 0x3f)); } DRM_DEBUG("Setting FIFO watermarks - A: %d, B: %d, C: %d, SR %d\n", @@ -1935,8 +1937,6 @@ static void i9xx_update_wm(struct drm_device *dev, int planea_clock, I915_WRITE(FW_BLC, fwater_lo); I915_WRITE(FW_BLC2, fwater_hi); - if (IS_I9XX(dev)) - I915_WRITE(FW_BLC_SELF, (srwm & 0x3f)); } static void i830_update_wm(struct drm_device *dev, int planea_clock, -- GitLab From c5ad4f592e27d782faea0a787d9181f192a69ef0 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Sun, 12 Jul 2009 11:40:34 +0000 Subject: [PATCH 0072/1342] atl1c: add missing parentheses Parentheses are required or the comparison occurs before the bitand. Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/atl1c/atl1c.h | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/net/atl1c/atl1c.h b/drivers/net/atl1c/atl1c.h index e1658ef3fcd..2a1120ad2e7 100644 --- a/drivers/net/atl1c/atl1c.h +++ b/drivers/net/atl1c/atl1c.h @@ -188,14 +188,14 @@ struct atl1c_tpd_ext_desc { #define RRS_HDS_TYPE_DATA 2 #define RRS_IS_NO_HDS_TYPE(flag) \ - (((flag) >> (RRS_HDS_TYPE_SHIFT)) & RRS_HDS_TYPE_MASK == 0) + ((((flag) >> (RRS_HDS_TYPE_SHIFT)) & RRS_HDS_TYPE_MASK) == 0) #define RRS_IS_HDS_HEAD(flag) \ - (((flag) >> (RRS_HDS_TYPE_SHIFT)) & RRS_HDS_TYPE_MASK == \ + ((((flag) >> (RRS_HDS_TYPE_SHIFT)) & RRS_HDS_TYPE_MASK) == \ RRS_HDS_TYPE_HEAD) #define RRS_IS_HDS_DATA(flag) \ - (((flag) >> (RRS_HDS_TYPE_SHIFT)) & RRS_HDS_TYPE_MASK == \ + ((((flag) >> (RRS_HDS_TYPE_SHIFT)) & RRS_HDS_TYPE_MASK) == \ RRS_HDS_TYPE_DATA) /* rrs word 3 bit 0:31 */ @@ -245,7 +245,7 @@ struct atl1c_tpd_ext_desc { #define RRS_PACKET_TYPE_802_3 1 #define RRS_PACKET_TYPE_ETH 0 #define RRS_PACKET_IS_ETH(word) \ - (((word) >> RRS_PACKET_TYPE_SHIFT) & RRS_PACKET_TYPE_MASK == \ + ((((word) >> RRS_PACKET_TYPE_SHIFT) & RRS_PACKET_TYPE_MASK) == \ RRS_PACKET_TYPE_ETH) #define RRS_RXD_IS_VALID(word) \ ((((word) >> RRS_RXD_UPDATED_SHIFT) & RRS_RXD_UPDATED_MASK) == 1) -- GitLab From 37b76c697f4ac082e9923dfa8e8aecc8bc54a8e1 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Sun, 12 Jul 2009 12:57:38 +0000 Subject: [PATCH 0073/1342] atl1c: misplaced parenthesis Fix misplaced parenthesis Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/atl1c/atl1c_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/atl1c/atl1c_main.c b/drivers/net/atl1c/atl1c_main.c index cd547a205fb..a383122679d 100644 --- a/drivers/net/atl1c/atl1c_main.c +++ b/drivers/net/atl1c/atl1c_main.c @@ -1689,7 +1689,7 @@ static void atl1c_clean_rx_irq(struct atl1c_adapter *adapter, u8 que, if (likely(RRS_RXD_IS_VALID(rrs->word3))) { rfd_num = (rrs->word0 >> RRS_RX_RFD_CNT_SHIFT) & RRS_RX_RFD_CNT_MASK; - if (unlikely(rfd_num) != 1) + if (unlikely(rfd_num != 1)) /* TODO support mul rfd*/ if (netif_msg_rx_err(adapter)) dev_warn(&pdev->dev, -- GitLab From e36b9d16c6a6d0f59803b3ef04ff3c22c3844c10 Mon Sep 17 00:00:00 2001 From: Moni Shoua Date: Wed, 15 Jul 2009 04:56:31 +0000 Subject: [PATCH 0074/1342] bonding: clean muticast addresses when device changes type Bonding device forbids slave device of different types under the same master. However, it is possible for a bonding master to change type during its lifetime. This can be either from ARPHRD_ETHER to ARPHRD_INFINIBAND or the other way arround. The change of type requires device level multicast address cleanup because device level multicast addresses depend on the device type. The patch adds a call to dev_close() before the bonding master changes type and dev_open() just after that. In the example below I enslaved an IPoIB device (ib0) under bond0. Since each bonding master starts as device of type ARPHRD_ETHER by default, a change of type occurs when ib0 is enslaved. This is how /proc/net/dev_mcast looks like without the patch 5 bond0 1 0 00ffffffff12601bffff000000000001ff96ca05 5 bond0 1 0 01005e000116 5 bond0 1 0 01005e7ffffd 5 bond0 1 0 01005e000001 5 bond0 1 0 333300000001 6 ib0 1 0 00ffffffff12601bffff000000000001ff96ca05 6 ib0 1 0 333300000001 6 ib0 1 0 01005e000001 6 ib0 1 0 01005e7ffffd 6 ib0 1 0 01005e000116 6 ib0 1 0 00ffffffff12401bffff00000000000000000001 6 ib0 1 0 00ffffffff12601bffff00000000000000000001 and this is how it looks like after the patch. 5 bond0 1 0 00ffffffff12601bffff000000000001ff96ca05 5 bond0 1 0 00ffffffff12601bffff00000000000000000001 5 bond0 1 0 00ffffffff12401bffff0000000000000ffffffd 5 bond0 1 0 00ffffffff12401bffff00000000000000000116 5 bond0 1 0 00ffffffff12401bffff00000000000000000001 6 ib0 1 0 00ffffffff12601bffff000000000001ff96ca05 6 ib0 1 0 00ffffffff12401bffff00000000000000000116 6 ib0 1 0 00ffffffff12401bffff0000000000000ffffffd 6 ib0 2 0 00ffffffff12401bffff00000000000000000001 6 ib0 2 0 00ffffffff12601bffff00000000000000000001 Signed-off-by: Moni Shoua Signed-off-by: Jay Vosburgh Signed-off-by: David S. Miller --- drivers/net/bonding/bond_main.c | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-) diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c index d927f71af8a..aa1be1fecee 100644 --- a/drivers/net/bonding/bond_main.c +++ b/drivers/net/bonding/bond_main.c @@ -1459,8 +1459,16 @@ int bond_enslave(struct net_device *bond_dev, struct net_device *slave_dev) * ether type (eg ARPHRD_ETHER and ARPHRD_INFINIBAND) share the same bond */ if (bond->slave_cnt == 0) { - if (slave_dev->type != ARPHRD_ETHER) - bond_setup_by_slave(bond_dev, slave_dev); + if (bond_dev->type != slave_dev->type) { + dev_close(bond_dev); + pr_debug("%s: change device type from %d to %d\n", + bond_dev->name, bond_dev->type, slave_dev->type); + if (slave_dev->type != ARPHRD_ETHER) + bond_setup_by_slave(bond_dev, slave_dev); + else + ether_setup(bond_dev); + dev_open(bond_dev); + } } else if (bond_dev->type != slave_dev->type) { pr_err(DRV_NAME ": %s ether type (%d) is different " "from other slaves (%d), can not enslave it.\n", -- GitLab From 303d67c288319768b19ed8dbed429fef7eb7c275 Mon Sep 17 00:00:00 2001 From: Krzysztof Halasa Date: Tue, 14 Jul 2009 11:01:54 +0000 Subject: [PATCH 0075/1342] E100: work around the driver using streaming DMA mapping for RX descriptors. E100 places it's RX packet descriptors inside skb->data and uses them with bidirectional streaming DMA mapping. Unfortunately it fails to transfer skb->data ownership to the device after it reads the descriptor's status, breaking on non-coherent (e.g., ARM) platforms. This have to be converted to use coherent memory for the descriptors. Signed-off-by: Krzysztof Halasa Acked-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/e100.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/net/e100.c b/drivers/net/e100.c index efa680f4b8d..41b648a67fe 100644 --- a/drivers/net/e100.c +++ b/drivers/net/e100.c @@ -1897,6 +1897,9 @@ static int e100_rx_indicate(struct nic *nic, struct rx *rx, if (ioread8(&nic->csr->scb.status) & rus_no_res) nic->ru_running = RU_SUSPENDED; + pci_dma_sync_single_for_device(nic->pdev, rx->dma_addr, + sizeof(struct rfd), + PCI_DMA_BIDIRECTIONAL); return -ENODATA; } -- GitLab From 4dc6dc7162c08b9965163c9ab3f9375d4adff2c7 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Wed, 15 Jul 2009 23:13:10 +0000 Subject: [PATCH 0076/1342] net: sock_copy() fixes Commit e912b1142be8f1e2c71c71001dc992c6e5eb2ec1 (net: sk_prot_alloc() should not blindly overwrite memory) took care of not zeroing whole new socket at allocation time. sock_copy() is another spot where we should be very careful. We should not set refcnt to a non null value, until we are sure other fields are correctly setup, or a lockless reader could catch this socket by mistake, while not fully (re)initialized. This patch puts sk_node & sk_refcnt to the very beginning of struct sock to ease sock_copy() & sk_prot_alloc() job. We add appropriate smp_wmb() before sk_refcnt initializations to match our RCU requirements (changes to sock keys should be committed to memory before sk_refcnt setting) Signed-off-by: Eric Dumazet Signed-off-by: David S. Miller --- include/net/sock.h | 32 +++++++++++++++++++------------- net/core/sock.c | 20 ++++++++++++++++++-- 2 files changed, 37 insertions(+), 15 deletions(-) diff --git a/include/net/sock.h b/include/net/sock.h index 2c0da9239b9..950409dcec3 100644 --- a/include/net/sock.h +++ b/include/net/sock.h @@ -104,15 +104,15 @@ struct net; /** * struct sock_common - minimal network layer representation of sockets + * @skc_node: main hash linkage for various protocol lookup tables + * @skc_nulls_node: main hash linkage for UDP/UDP-Lite protocol + * @skc_refcnt: reference count + * @skc_hash: hash value used with various protocol lookup tables * @skc_family: network address family * @skc_state: Connection state * @skc_reuse: %SO_REUSEADDR setting * @skc_bound_dev_if: bound device index if != 0 - * @skc_node: main hash linkage for various protocol lookup tables - * @skc_nulls_node: main hash linkage for UDP/UDP-Lite protocol * @skc_bind_node: bind hash linkage for various protocol lookup tables - * @skc_refcnt: reference count - * @skc_hash: hash value used with various protocol lookup tables * @skc_prot: protocol handlers inside a network family * @skc_net: reference to the network namespace of this socket * @@ -120,17 +120,21 @@ struct net; * for struct sock and struct inet_timewait_sock. */ struct sock_common { - unsigned short skc_family; - volatile unsigned char skc_state; - unsigned char skc_reuse; - int skc_bound_dev_if; + /* + * first fields are not copied in sock_copy() + */ union { struct hlist_node skc_node; struct hlist_nulls_node skc_nulls_node; }; - struct hlist_node skc_bind_node; atomic_t skc_refcnt; + unsigned int skc_hash; + unsigned short skc_family; + volatile unsigned char skc_state; + unsigned char skc_reuse; + int skc_bound_dev_if; + struct hlist_node skc_bind_node; struct proto *skc_prot; #ifdef CONFIG_NET_NS struct net *skc_net; @@ -208,15 +212,17 @@ struct sock { * don't add nothing before this first member (__sk_common) --acme */ struct sock_common __sk_common; +#define sk_node __sk_common.skc_node +#define sk_nulls_node __sk_common.skc_nulls_node +#define sk_refcnt __sk_common.skc_refcnt + +#define sk_copy_start __sk_common.skc_hash +#define sk_hash __sk_common.skc_hash #define sk_family __sk_common.skc_family #define sk_state __sk_common.skc_state #define sk_reuse __sk_common.skc_reuse #define sk_bound_dev_if __sk_common.skc_bound_dev_if -#define sk_node __sk_common.skc_node -#define sk_nulls_node __sk_common.skc_nulls_node #define sk_bind_node __sk_common.skc_bind_node -#define sk_refcnt __sk_common.skc_refcnt -#define sk_hash __sk_common.skc_hash #define sk_prot __sk_common.skc_prot #define sk_net __sk_common.skc_net kmemcheck_bitfield_begin(flags); diff --git a/net/core/sock.c b/net/core/sock.c index ba5d2116aea..d9eec153d53 100644 --- a/net/core/sock.c +++ b/net/core/sock.c @@ -919,13 +919,19 @@ static inline void sock_lock_init(struct sock *sk) af_family_keys + sk->sk_family); } +/* + * Copy all fields from osk to nsk but nsk->sk_refcnt must not change yet, + * even temporarly, because of RCU lookups. sk_node should also be left as is. + */ static void sock_copy(struct sock *nsk, const struct sock *osk) { #ifdef CONFIG_SECURITY_NETWORK void *sptr = nsk->sk_security; #endif - - memcpy(nsk, osk, osk->sk_prot->obj_size); + BUILD_BUG_ON(offsetof(struct sock, sk_copy_start) != + sizeof(osk->sk_node) + sizeof(osk->sk_refcnt)); + memcpy(&nsk->sk_copy_start, &osk->sk_copy_start, + osk->sk_prot->obj_size - offsetof(struct sock, sk_copy_start)); #ifdef CONFIG_SECURITY_NETWORK nsk->sk_security = sptr; security_sk_clone(osk, nsk); @@ -1140,6 +1146,11 @@ struct sock *sk_clone(const struct sock *sk, const gfp_t priority) newsk->sk_err = 0; newsk->sk_priority = 0; + /* + * Before updating sk_refcnt, we must commit prior changes to memory + * (Documentation/RCU/rculist_nulls.txt for details) + */ + smp_wmb(); atomic_set(&newsk->sk_refcnt, 2); /* @@ -1855,6 +1866,11 @@ void sock_init_data(struct socket *sock, struct sock *sk) sk->sk_stamp = ktime_set(-1L, 0); + /* + * Before updating sk_refcnt, we must commit prior changes to memory + * (Documentation/RCU/rculist_nulls.txt for details) + */ + smp_wmb(); atomic_set(&sk->sk_refcnt, 1); atomic_set(&sk->sk_wmem_alloc, 1); atomic_set(&sk->sk_drops, 0); -- GitLab From 3d1454dd93e84ad1394b6b1646f13795e9f6928e Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Thu, 16 Jul 2009 13:20:57 +0000 Subject: [PATCH 0077/1342] sky2: revert shutdown changes The commit changes to shutdown path broke startup on some systems. revert commit c0bad0f2e4366d5bbfe0c4a7a80bca8f4b05272b Signed-off-by: Stephen Hemminger Signed-off-by: David S. Miller --- drivers/net/sky2.c | 9 +-------- 1 file changed, 1 insertion(+), 8 deletions(-) diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index daf961ab68b..ba768dfa59e 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -1151,14 +1151,7 @@ stopped: /* reset the Rx prefetch unit */ sky2_write32(hw, Y2_QADDR(rxq, PREF_UNIT_CTRL), PREF_UNIT_RST_SET); - - /* Reset the RAM Buffer receive queue */ - sky2_write8(hw, RB_ADDR(rxq, RB_CTRL), RB_RST_SET); - - /* Reset Rx MAC FIFO */ - sky2_write8(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), GMF_RST_SET); - - sky2_read8(hw, B0_CTST); + mmiowb(); } /* Clean out receive buffer area, assumes receiver hardware stopped */ -- GitLab From 86e713a06ab3e5b15a3189485ce33aa21b9e52ca Mon Sep 17 00:00:00 2001 From: Lucy Liu Date: Thu, 16 Jul 2009 13:43:10 +0000 Subject: [PATCH 0078/1342] ixgbe: clear mac address data block in DCB mode This change clears the address data block memory space, which is needed for the 82598 which does not have a SAN MAC. Signed-off-by: Lucy Liu Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_dcb_nl.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/net/ixgbe/ixgbe_dcb_nl.c b/drivers/net/ixgbe/ixgbe_dcb_nl.c index 7c5978ad929..5b8dab22c6d 100644 --- a/drivers/net/ixgbe/ixgbe_dcb_nl.c +++ b/drivers/net/ixgbe/ixgbe_dcb_nl.c @@ -175,6 +175,8 @@ static void ixgbe_dcbnl_get_perm_hw_addr(struct net_device *netdev, struct ixgbe_adapter *adapter = netdev_priv(netdev); int i, j; + memset(perm_addr, 0xff, MAX_ADDR_LEN); + for (i = 0; i < netdev->addr_len; i++) perm_addr[i] = adapter->hw.mac.perm_addr[i]; -- GitLab From 869f1c54e9aecde1dfd4349832ce9415a596be8e Mon Sep 17 00:00:00 2001 From: Lucy Liu Date: Thu, 16 Jul 2009 13:43:31 +0000 Subject: [PATCH 0079/1342] ixgbe: Remove DPRINTK messages in DCB mode Remove debug DPRINTK in DCB mode netlink interface. Signed-off-by: Lucy Liu Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_dcb_nl.c | 4 ---- 1 file changed, 4 deletions(-) diff --git a/drivers/net/ixgbe/ixgbe_dcb_nl.c b/drivers/net/ixgbe/ixgbe_dcb_nl.c index 5b8dab22c6d..da2c8514b8d 100644 --- a/drivers/net/ixgbe/ixgbe_dcb_nl.c +++ b/drivers/net/ixgbe/ixgbe_dcb_nl.c @@ -106,8 +106,6 @@ static u8 ixgbe_dcbnl_get_state(struct net_device *netdev) { struct ixgbe_adapter *adapter = netdev_priv(netdev); - DPRINTK(DRV, INFO, "Get DCB Admin Mode.\n"); - return !!(adapter->flags & IXGBE_FLAG_DCB_ENABLED); } @@ -116,8 +114,6 @@ static u8 ixgbe_dcbnl_set_state(struct net_device *netdev, u8 state) u8 err = 0; struct ixgbe_adapter *adapter = netdev_priv(netdev); - DPRINTK(DRV, INFO, "Set DCB Admin Mode.\n"); - if (state > 0) { /* Turn on DCB */ if (adapter->flags & IXGBE_FLAG_DCB_ENABLED) -- GitLab From 7fefe6a88494b00b151b5ca7bb84daaa781bbca7 Mon Sep 17 00:00:00 2001 From: Vincent CUISSARD Date: Thu, 16 Jul 2009 06:08:58 +0000 Subject: [PATCH 0080/1342] cdc-eem: bad crc checking When the driver received an EEM packet with CRC option enabled, driver must compute and check the CRC of the Ethernet data. Previous version computes CRC on Ethernet data plus the original CRC value. Skbuff is correctly trimed but the old length is used when CRC is computed. Signed-off-by: Vincent CUISSARD Signed-off-by: David S. Miller --- drivers/net/usb/cdc_eem.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/usb/cdc_eem.c b/drivers/net/usb/cdc_eem.c index cd35d50e46d..45cebfb302c 100644 --- a/drivers/net/usb/cdc_eem.c +++ b/drivers/net/usb/cdc_eem.c @@ -311,7 +311,7 @@ static int eem_rx_fixup(struct usbnet *dev, struct sk_buff *skb) * bmCRC = 0 : CRC = 0xDEADBEEF */ if (header & BIT(14)) - crc2 = ~crc32_le(~0, skb2->data, len); + crc2 = ~crc32_le(~0, skb2->data, skb2->len); else crc2 = 0xdeadbeef; -- GitLab From 0a09f4319c6d88c732ed46735f8584bbb95cac65 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Thu, 16 Jul 2009 15:26:55 +0900 Subject: [PATCH 0081/1342] block: fix failfast merge testing in elv_rq_merge_ok() Commit ab0fd1debe730ec9998678a0c53caefbd121ed10 tries to prevent merge of requests with different failfast settings. In elv_rq_merge_ok(), it compares new bio's failfast flags against the merge target request's. However, the flag testing accessors for bio and blk don't return boolean but the tested bit value directly and FAILFAST on bio and blk don't match, so directly comparing them with == results in false negative unnecessary preventing merge of readahead requests. This patch convert the results to boolean by negating them before comparison. Signed-off-by: Tejun Heo Cc: Jens Axboe Cc: Boaz Harrosh Cc: FUJITA Tomonori Cc: James Bottomley Cc: Jeff Garzik --- block/elevator.c | 13 +++++++++---- 1 file changed, 9 insertions(+), 4 deletions(-) diff --git a/block/elevator.c b/block/elevator.c index 6f2375339a9..2d511f9105e 100644 --- a/block/elevator.c +++ b/block/elevator.c @@ -101,11 +101,16 @@ int elv_rq_merge_ok(struct request *rq, struct bio *bio) return 0; /* - * Don't merge if failfast settings don't match + * Don't merge if failfast settings don't match. + * + * FIXME: The negation in front of each condition is necessary + * because bio and request flags use different bit positions + * and the accessors return those bits directly. This + * ugliness will soon go away. */ - if (bio_failfast_dev(bio) != blk_failfast_dev(rq) || - bio_failfast_transport(bio) != blk_failfast_transport(rq) || - bio_failfast_driver(bio) != blk_failfast_driver(rq)) + if (!bio_failfast_dev(bio) != !blk_failfast_dev(rq) || + !bio_failfast_transport(bio) != !blk_failfast_transport(rq) || + !bio_failfast_driver(bio) != !blk_failfast_driver(rq)) return 0; if (!elv_iosched_allow_merge(rq, bio)) -- GitLab From 8f47428704c2fd6f787a6f340071b9c338b65803 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Mon, 13 Jul 2009 22:43:41 +0200 Subject: [PATCH 0082/1342] ataflop: adjust NULL test dtp is derefenced on the lines above the test !dtp, and so it cannot be NULL at this point. A simplified version of the semantic match that finds this problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // @r@ expression x,E,E1; identifier f,l; position p1,p2; @@ *x@p1->f = E1; ... when != x = E when != goto l; ( *x@p2 == NULL | *x@p2 != NULL ) // Signed-off-by: Julia Lawall Signed-off-by: Tejun Heo --- drivers/block/ataflop.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/block/ataflop.c b/drivers/block/ataflop.c index f5e7180d7f4..3ff02941b3d 100644 --- a/drivers/block/ataflop.c +++ b/drivers/block/ataflop.c @@ -1627,7 +1627,7 @@ static int fd_ioctl(struct block_device *bdev, fmode_t mode, drive, dtp->blocks, dtp->spt, dtp->stretch); /* sanity check */ - if (!dtp || setprm.track != dtp->blocks/dtp->spt/2 || + if (setprm.track != dtp->blocks/dtp->spt/2 || setprm.head != 2) { redo_fd_request(); return -EINVAL; -- GitLab From 9cb308ce8d32a1fb3600acab6034e19a90228743 Mon Sep 17 00:00:00 2001 From: Xiaotian Feng Date: Fri, 17 Jul 2009 15:26:26 +0800 Subject: [PATCH 0083/1342] block: sysfs fix mismatched queue_var_{store,show} in 64bit kernel In blk-sysfs.c, queue_var_store uses unsigned long to store data, but queue_var_show uses unsigned int to show data. This causes, # echo 70000000000 > /sys/block//queue/read_ahead_kb # cat /sys/block//queue/read_ahead_kb => get wrong value Fix it by using unsigned long. While at it, convert queue_rq_affinity_show() such that it uses bool variable instead of explicit != 0 testing. Signed-off-by: Xiaotian Feng Signed-off-by: Tejun Heo --- block/blk-sysfs.c | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-) diff --git a/block/blk-sysfs.c b/block/blk-sysfs.c index b1cd04087d6..418d6361968 100644 --- a/block/blk-sysfs.c +++ b/block/blk-sysfs.c @@ -16,9 +16,9 @@ struct queue_sysfs_entry { }; static ssize_t -queue_var_show(unsigned int var, char *page) +queue_var_show(unsigned long var, char *page) { - return sprintf(page, "%d\n", var); + return sprintf(page, "%lu\n", var); } static ssize_t @@ -77,7 +77,8 @@ queue_requests_store(struct request_queue *q, const char *page, size_t count) static ssize_t queue_ra_show(struct request_queue *q, char *page) { - int ra_kb = q->backing_dev_info.ra_pages << (PAGE_CACHE_SHIFT - 10); + unsigned long ra_kb = q->backing_dev_info.ra_pages << + (PAGE_CACHE_SHIFT - 10); return queue_var_show(ra_kb, (page)); } @@ -189,9 +190,9 @@ static ssize_t queue_nomerges_store(struct request_queue *q, const char *page, static ssize_t queue_rq_affinity_show(struct request_queue *q, char *page) { - unsigned int set = test_bit(QUEUE_FLAG_SAME_COMP, &q->queue_flags); + bool set = test_bit(QUEUE_FLAG_SAME_COMP, &q->queue_flags); - return queue_var_show(set != 0, page); + return queue_var_show(set, page); } static ssize_t -- GitLab From 54a8fa62c94d74a8f2d18f99cff95953e5c623b7 Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Fri, 17 Jul 2009 04:42:28 +0000 Subject: [PATCH 0084/1342] MAINTAINERS entry for STRIP driver The web server does no longer exist, it's not on archive.org nor does there seem to be any mirror. MAINTAINERS | 1 - 1 files changed, 0 insertions(+), 1 deletions(-) Signed-off-by: David S. Miller --- MAINTAINERS | 1 - 1 file changed, 1 deletion(-) diff --git a/MAINTAINERS b/MAINTAINERS index f608e1debdd..0bd82fa6d2f 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -5539,7 +5539,6 @@ S: Maintained F: drivers/net/starfire* STARMODE RADIO IP (STRIP) PROTOCOL DRIVER -W: http://mosquitonet.Stanford.EDU/strip.html S: Orphan F: drivers/net/wireless/strip.c F: include/linux/if_strip.h -- GitLab From 673325951ef440ebace311bd542a9378d1b3025b Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Fri, 17 Jul 2009 04:47:19 +0000 Subject: [PATCH 0085/1342] Update Andreas Koensgen's email address The kernel has used a stale email address of Andreas for a few years. Signed-off-by: Ralf Baechle Signed-off-by: David S. Miller --- CREDITS | 2 +- Documentation/networking/6pack.txt | 2 +- MAINTAINERS | 2 +- drivers/net/hamradio/6pack.c | 2 +- 4 files changed, 4 insertions(+), 4 deletions(-) diff --git a/CREDITS b/CREDITS index 2b88fb37ad5..e76d300e9fe 100644 --- a/CREDITS +++ b/CREDITS @@ -1856,7 +1856,7 @@ E: rfkoenig@immd4.informatik.uni-erlangen.de D: The Linux Support Team Erlangen N: Andreas Koensgen -E: ajk@iehk.rwth-aachen.de +E: ajk@comnets.uni-bremen.de D: 6pack driver for AX.25 N: Harald Koerfgen diff --git a/Documentation/networking/6pack.txt b/Documentation/networking/6pack.txt index d0777a1200e..8f339428fdf 100644 --- a/Documentation/networking/6pack.txt +++ b/Documentation/networking/6pack.txt @@ -1,7 +1,7 @@ This is the 6pack-mini-HOWTO, written by Andreas Könsgen DG3KQ -Internet: ajk@iehk.rwth-aachen.de +Internet: ajk@comnets.uni-bremen.de AMPR-net: dg3kq@db0pra.ampr.org AX.25: dg3kq@db0ach.#nrw.deu.eu diff --git a/MAINTAINERS b/MAINTAINERS index 0bd82fa6d2f..6c6bb95acb1 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -150,7 +150,7 @@ F: drivers/scsi/53c700* 6PACK NETWORK DRIVER FOR AX.25 P: Andreas Koensgen -M: ajk@iehk.rwth-aachen.de +M: ajk@comnets.uni-bremen.de L: linux-hams@vger.kernel.org S: Maintained F: drivers/net/hamradio/6pack.c diff --git a/drivers/net/hamradio/6pack.c b/drivers/net/hamradio/6pack.c index 155160052c8..981ab530e9a 100644 --- a/drivers/net/hamradio/6pack.c +++ b/drivers/net/hamradio/6pack.c @@ -3,7 +3,7 @@ * devices like TTY. It interfaces between a raw TTY and the * kernel's AX.25 protocol layers. * - * Authors: Andreas Könsgen + * Authors: Andreas Könsgen * Ralf Baechle DL5RB * * Quite a lot of stuff "stolen" by Joerg Reuter from slip.c, written by -- GitLab From 14d87e6c399f3942d63dff41447ff08a615d9a6b Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Fri, 17 Jul 2009 10:28:19 -0700 Subject: [PATCH 0086/1342] sparc: Fix cleanup crash in bbc_envctrl_cleanup() MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit If kthread_run() fails or never gets to run we'll have NULL or a pointer encoded error in kenvctrld_task, rather than a legitimate task pointer. So this makes bbc_envctrl_cleanup() crash as it passed this bogus pointer into kthread_stop(). Reported-by: BERTRAND Joël Signed-off-by: David S. Miller --- drivers/sbus/char/bbc_envctrl.c | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-) diff --git a/drivers/sbus/char/bbc_envctrl.c b/drivers/sbus/char/bbc_envctrl.c index 15dab96d05e..7c815d3327f 100644 --- a/drivers/sbus/char/bbc_envctrl.c +++ b/drivers/sbus/char/bbc_envctrl.c @@ -537,8 +537,12 @@ int bbc_envctrl_init(struct bbc_i2c_bus *bp) } if (temp_index != 0 && fan_index != 0) { kenvctrld_task = kthread_run(kenvctrld, NULL, "kenvctrld"); - if (IS_ERR(kenvctrld_task)) - return PTR_ERR(kenvctrld_task); + if (IS_ERR(kenvctrld_task)) { + int err = PTR_ERR(kenvctrld_task); + + kenvctrld_task = NULL; + return err; + } } return 0; @@ -561,7 +565,8 @@ void bbc_envctrl_cleanup(struct bbc_i2c_bus *bp) struct bbc_cpu_temperature *tp, *tpos; struct bbc_fan_control *fp, *fpos; - kthread_stop(kenvctrld_task); + if (kenvctrld_task) + kthread_stop(kenvctrld_task); list_for_each_entry_safe(tp, tpos, &bp->temps, bp_list) { list_del(&tp->bp_list); -- GitLab From eb9069119d1c4bc856b4c1339abcad0105691e71 Mon Sep 17 00:00:00 2001 From: Haojian Zhuang Date: Wed, 15 Jul 2009 19:47:24 +0800 Subject: [PATCH 0087/1342] [ARM] pxa: fix gpio issue in zylonite WARNING: at drivers/gpio/gpiolib.c:83 gpio_ensure_requested+0x58/0xbc() autorequest GPIO-71 Modules linked in: [] (unwind_backtrace+0x0/0xe8) from [] (warn_slowpath_common+0x48/0x78) [] (warn_slowpath_common+0x48/0x78) from [] (warn_slowpath_fmt+0x28/0x38) [] (warn_slowpath_fmt+0x28/0x38) from [] (gpio_ensure_requested+0x58/0xbc) [] (gpio_ensure_requested+0x58/0xbc) from [] (gpio_direction_input+0x80/0xf4) [] (gpio_direction_input+0x80/0xf4) from [] (zylonite_pxa300_init+0x108/0x214) [] (zylonite_pxa300_init+0x108/0x214) from [] (zylonite_init+0x8/0x84) [] (zylonite_init+0x8/0x84) from [] (customize_machine+0x18/0x24) [] (customize_machine+0x18/0x24) from [] (do_one_initcall+0x30/0x1b0) [] (do_one_initcall+0x30/0x1b0) from [] (kernel_init+0xa4/0x11c) [] (kernel_init+0xa4/0x11c) from [] (kernel_thread_exit+0x0/0x8) ---[ end trace 1b75b31a2719ed1c ]--- This issue is caused by using gpio pin without request. Add gpio_request() into zylonite. To simplify the code, error checking is omitted since this is being performed early. Signed-off-by: Haojian Zhuang Signed-off-by: Eric Miao --- arch/arm/mach-pxa/zylonite_pxa300.c | 2 ++ arch/arm/mach-pxa/zylonite_pxa320.c | 2 ++ 2 files changed, 4 insertions(+) diff --git a/arch/arm/mach-pxa/zylonite_pxa300.c b/arch/arm/mach-pxa/zylonite_pxa300.c index cefd1c0a854..84095440a87 100644 --- a/arch/arm/mach-pxa/zylonite_pxa300.c +++ b/arch/arm/mach-pxa/zylonite_pxa300.c @@ -197,10 +197,12 @@ static void __init zylonite_detect_lcd_panel(void) for (i = 0; i < NUM_LCD_DETECT_PINS; i++) { id = id << 1; gpio = mfp_to_gpio(lcd_detect_pins[i]); + gpio_request(gpio, "LCD_ID_PINS"); gpio_direction_input(gpio); if (gpio_get_value(gpio)) id = id | 0x1; + gpio_free(gpio); } /* lcd id, flush out bit 1 */ diff --git a/arch/arm/mach-pxa/zylonite_pxa320.c b/arch/arm/mach-pxa/zylonite_pxa320.c index cc5a2283360..60d08f23f5e 100644 --- a/arch/arm/mach-pxa/zylonite_pxa320.c +++ b/arch/arm/mach-pxa/zylonite_pxa320.c @@ -176,10 +176,12 @@ static void __init zylonite_detect_lcd_panel(void) for (i = 0; i < NUM_LCD_DETECT_PINS; i++) { id = id << 1; gpio = mfp_to_gpio(lcd_detect_pins[i]); + gpio_request(gpio, "LCD_ID_PINS"); gpio_direction_input(gpio); if (gpio_get_value(gpio)) id = id | 0x1; + gpio_free(gpio); } /* lcd id, flush out bit 1 */ -- GitLab From ecf763c5677faee04d47333e6ed8e9539a427770 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Thu, 16 Jul 2009 19:37:29 +0200 Subject: [PATCH 0088/1342] [ARM] pxa: add STUART MFP config for PalmTX,T5,LD Signed-off-by: Marek Vasut Signed-off-by: Eric Miao --- arch/arm/mach-pxa/palmld.c | 4 ++++ arch/arm/mach-pxa/palmt5.c | 4 ++++ arch/arm/mach-pxa/palmtx.c | 4 ++++ 3 files changed, 12 insertions(+) diff --git a/arch/arm/mach-pxa/palmld.c b/arch/arm/mach-pxa/palmld.c index ed70f281dd0..169fcc18154 100644 --- a/arch/arm/mach-pxa/palmld.c +++ b/arch/arm/mach-pxa/palmld.c @@ -128,6 +128,10 @@ static unsigned long palmld_pin_config[] __initdata = { GPIO38_GPIO, /* wifi ready */ GPIO81_GPIO, /* wifi reset */ + /* FFUART */ + GPIO34_FFUART_RXD, + GPIO39_FFUART_TXD, + /* HDD */ GPIO98_GPIO, /* HDD reset */ GPIO115_GPIO, /* HDD power */ diff --git a/arch/arm/mach-pxa/palmt5.c b/arch/arm/mach-pxa/palmt5.c index aae64a12a73..33f726ff55e 100644 --- a/arch/arm/mach-pxa/palmt5.c +++ b/arch/arm/mach-pxa/palmt5.c @@ -111,6 +111,10 @@ static unsigned long palmt5_pin_config[] __initdata = { /* PWM */ GPIO16_PWM0_OUT, + /* FFUART */ + GPIO34_FFUART_RXD, + GPIO39_FFUART_TXD, + /* MISC */ GPIO10_GPIO, /* hotsync button */ GPIO90_GPIO, /* power detect */ diff --git a/arch/arm/mach-pxa/palmtx.c b/arch/arm/mach-pxa/palmtx.c index 6c15d84bde5..83d02087958 100644 --- a/arch/arm/mach-pxa/palmtx.c +++ b/arch/arm/mach-pxa/palmtx.c @@ -127,6 +127,10 @@ static unsigned long palmtx_pin_config[] __initdata = { GPIO76_LCD_PCLK, GPIO77_LCD_BIAS, + /* FFUART */ + GPIO34_FFUART_RXD, + GPIO39_FFUART_TXD, + /* MISC. */ GPIO10_GPIO, /* hotsync button */ GPIO12_GPIO, /* power detect */ -- GitLab From 54fdc5816631b43ba55fc3206d7add2d85850bc6 Mon Sep 17 00:00:00 2001 From: Fabio Checconi Date: Thu, 16 Jul 2009 12:32:27 +0200 Subject: [PATCH 0089/1342] sched: Account for vruntime wrapping I spotted two sites that didn't take vruntime wrap-around into account. Fix these by creating a comparison helper that does do so. Signed-off-by: Fabio Checconi Signed-off-by: Peter Zijlstra LKML-Reference: Signed-off-by: Ingo Molnar --- kernel/sched_fair.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) diff --git a/kernel/sched_fair.c b/kernel/sched_fair.c index 7c248dc30f4..9ffb2b2ceba 100644 --- a/kernel/sched_fair.c +++ b/kernel/sched_fair.c @@ -266,6 +266,12 @@ static inline u64 min_vruntime(u64 min_vruntime, u64 vruntime) return min_vruntime; } +static inline int entity_before(struct sched_entity *a, + struct sched_entity *b) +{ + return (s64)(a->vruntime - b->vruntime) < 0; +} + static inline s64 entity_key(struct cfs_rq *cfs_rq, struct sched_entity *se) { return se->vruntime - cfs_rq->min_vruntime; @@ -1017,7 +1023,7 @@ static void yield_task_fair(struct rq *rq) /* * Already in the rightmost position? */ - if (unlikely(!rightmost || rightmost->vruntime < se->vruntime)) + if (unlikely(!rightmost || entity_before(rightmost, se))) return; /* @@ -1713,7 +1719,7 @@ static void task_new_fair(struct rq *rq, struct task_struct *p) /* 'curr' will be NULL if the child belongs to a different group */ if (sysctl_sched_child_runs_first && this_cpu == task_cpu(p) && - curr && curr->vruntime < se->vruntime) { + curr && entity_before(curr, se)) { /* * Upon rescheduling, sched_class::put_prev_task() will place * 'current' within the tree based on its new key value. -- GitLab From 413ee3b48ab582ffea33e7e140c7a2c5ea657e9a Mon Sep 17 00:00:00 2001 From: Anton Blanchard Date: Thu, 16 Jul 2009 15:15:52 +0200 Subject: [PATCH 0090/1342] perf_counter: Make sure we dont leak kernel memory to userspace There are a few places we are leaking tiny amounts of kernel memory to userspace. This happens when writing out strings because we always align the end to 64 bits. To avoid this we should always use an appropriately sized temporary buffer and ensure it is zeroed. Since d_path assembles the string from the end of the buffer backwards, we need to add 64 bits after the buffer to allow for alignment. We also need to copy arch_vma_name to the temporary buffer, because if we use it directly we may end up copying to userspace a number of bytes after the end of the string constant. Signed-off-by: Anton Blanchard Signed-off-by: Peter Zijlstra LKML-Reference: <20090716104817.273972048@samba.org> Signed-off-by: Ingo Molnar --- kernel/perf_counter.c | 19 +++++++++++++++---- 1 file changed, 15 insertions(+), 4 deletions(-) diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index c6c38fb7766..f7a8ab9576e 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -2968,8 +2968,10 @@ static void perf_counter_comm_event(struct perf_comm_event *comm_event) struct perf_cpu_context *cpuctx; struct perf_counter_context *ctx; unsigned int size; - char *comm = comm_event->task->comm; + char comm[TASK_COMM_LEN]; + memset(comm, 0, sizeof(comm)); + strncpy(comm, comm_event->task->comm, sizeof(comm)); size = ALIGN(strlen(comm)+1, sizeof(u64)); comm_event->comm = comm; @@ -3088,8 +3090,15 @@ static void perf_counter_mmap_event(struct perf_mmap_event *mmap_event) char *buf = NULL; const char *name; + memset(tmp, 0, sizeof(tmp)); + if (file) { - buf = kzalloc(PATH_MAX, GFP_KERNEL); + /* + * d_path works from the end of the buffer backwards, so we + * need to add enough zero bytes after the string to handle + * the 64bit alignment we do later. + */ + buf = kzalloc(PATH_MAX + sizeof(u64), GFP_KERNEL); if (!buf) { name = strncpy(tmp, "//enomem", sizeof(tmp)); goto got_name; @@ -3100,9 +3109,11 @@ static void perf_counter_mmap_event(struct perf_mmap_event *mmap_event) goto got_name; } } else { - name = arch_vma_name(mmap_event->vma); - if (name) + if (arch_vma_name(mmap_event->vma)) { + name = strncpy(tmp, arch_vma_name(mmap_event->vma), + sizeof(tmp)); goto got_name; + } if (!vma->vm_mm) { name = strncpy(tmp, "[vdso]", sizeof(tmp)); -- GitLab From 11b5f81e1b0ea0bc84fe32f0a27054e052b2bf84 Mon Sep 17 00:00:00 2001 From: Anton Blanchard Date: Thu, 16 Jul 2009 15:44:29 +0200 Subject: [PATCH 0091/1342] perf_counter: Synthesize VDSO mmap event perf record synthesizes mmap events for the running process. Right now it just catches file mappings, but we can check for the vdso symbol and add that too. Signed-off-by: Anton Blanchard Signed-off-by: Peter Zijlstra LKML-Reference: <20090716104817.517264409@samba.org> Signed-off-by: Ingo Molnar --- tools/perf/builtin-record.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/tools/perf/builtin-record.c b/tools/perf/builtin-record.c index 4ef78a5e6f3..072aaf0369f 100644 --- a/tools/perf/builtin-record.c +++ b/tools/perf/builtin-record.c @@ -313,6 +313,10 @@ static void pid_synthesize_mmap_samples(pid_t pid) if (*pbf == 'x') { /* vm_exec */ char *execname = strchr(bf, '/'); + /* Catch VDSO */ + if (execname == NULL) + execname = strstr(bf, "[vdso]"); + if (execname == NULL) continue; -- GitLab From ed900c054b541254f0ce5cedaf75206e29bd614e Mon Sep 17 00:00:00 2001 From: Anton Blanchard Date: Thu, 16 Jul 2009 15:44:29 +0200 Subject: [PATCH 0092/1342] perf_counter: Log vfork as a fork event Right now we don't output vfork events. Even though we should always see an exec after a vfork, we may get perfcounter samples between the vfork and exec. These samples can lead to some confusion when parsing perfcounter data. To keep things consistent we should always log a fork event. It will result in a little more log data, but is less confusing to trace parsing tools. Signed-off-by: Anton Blanchard Signed-off-by: Peter Zijlstra LKML-Reference: <20090716104817.589309391@samba.org> Signed-off-by: Ingo Molnar --- kernel/fork.c | 9 +++------ 1 file changed, 3 insertions(+), 6 deletions(-) diff --git a/kernel/fork.c b/kernel/fork.c index 467746b3f0a..4812d60b29f 100644 --- a/kernel/fork.c +++ b/kernel/fork.c @@ -1408,14 +1408,11 @@ long do_fork(unsigned long clone_flags, if (clone_flags & CLONE_VFORK) { p->vfork_done = &vfork; init_completion(&vfork); - } else if (!(clone_flags & CLONE_VM)) { - /* - * vfork will do an exec which will call - * set_task_comm() - */ - perf_counter_fork(p); } + if (!(clone_flags & CLONE_THREAD)) + perf_counter_fork(p); + audit_finish_fork(p); tracehook_report_clone(regs, clone_flags, nr, p); -- GitLab From 4bba828dd9bb950ad1fe340ef148a5436a10f131 Mon Sep 17 00:00:00 2001 From: Anton Blanchard Date: Thu, 16 Jul 2009 15:44:29 +0200 Subject: [PATCH 0093/1342] perf_counter: Add perf record option to log addresses Add the -d or --data option to log event addresses (eg page faults). Signed-off-by: Anton Blanchard Signed-off-by: Peter Zijlstra LKML-Reference: <20090716104817.697698033@samba.org> Signed-off-by: Ingo Molnar --- tools/perf/builtin-record.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/tools/perf/builtin-record.c b/tools/perf/builtin-record.c index 072aaf0369f..68a9be0d151 100644 --- a/tools/perf/builtin-record.c +++ b/tools/perf/builtin-record.c @@ -43,6 +43,7 @@ static int call_graph = 0; static int verbose = 0; static int inherit_stat = 0; static int no_samples = 0; +static int sample_address = 0; static long samples; static struct timeval last_read; @@ -405,6 +406,9 @@ static void create_counter(int counter, int cpu, pid_t pid) if (inherit_stat) attr->inherit_stat = 1; + if (sample_address) + attr->sample_type |= PERF_SAMPLE_ADDR; + if (call_graph) attr->sample_type |= PERF_SAMPLE_CALLCHAIN; @@ -649,6 +653,8 @@ static const struct option options[] = { "be more verbose (show counter open errors, etc)"), OPT_BOOLEAN('s', "stat", &inherit_stat, "per thread counts"), + OPT_BOOLEAN('d', "data", &sample_address, + "Sample addresses"), OPT_BOOLEAN('n', "no-samples", &no_samples, "don't sample"), OPT_END() -- GitLab From 1483b19f8f5e8ad0c8816de368b099322dad4db5 Mon Sep 17 00:00:00 2001 From: Anton Blanchard Date: Thu, 16 Jul 2009 15:44:29 +0200 Subject: [PATCH 0094/1342] perf_counter: Make call graph option consistent perf record uses -g for logging call graph data but perf report uses -c to print call graph data. Be consistent and use -g everywhere for call graph data. Also update the help text to reflect the current default - fractal,0.5 Signed-off-by: Anton Blanchard Acked-by: Frederic Weisbecker Signed-off-by: Peter Zijlstra LKML-Reference: <20090716104817.803604373@samba.org> Signed-off-by: Ingo Molnar --- tools/perf/builtin-report.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c index 4e5cc266311..4b980cce705 100644 --- a/tools/perf/builtin-report.c +++ b/tools/perf/builtin-report.c @@ -1891,9 +1891,9 @@ static const struct option options[] = { "regex filter to identify parent, see: '--sort parent'"), OPT_BOOLEAN('x', "exclude-other", &exclude_other, "Only display entries with parent-match"), - OPT_CALLBACK_DEFAULT('c', "callchain", NULL, "output_type,min_percent", + OPT_CALLBACK_DEFAULT('g', "call-graph", NULL, "output_type,min_percent", "Display callchains using output_type and min percent threshold. " - "Default: flat,0", &parse_callchain_opt, callchain_default_opt), + "Default: fractal,0.5", &parse_callchain_opt, callchain_default_opt), OPT_STRING('d', "dsos", &dso_list_str, "dso[,dso...]", "only consider symbols in these dsos"), OPT_STRING('C', "comms", &comm_list_str, "comm[,comm...]", -- GitLab From e5d490b252423605a77c54b2e35b10ea663763df Mon Sep 17 00:00:00 2001 From: Mel Gorman Date: Wed, 15 Jul 2009 12:23:11 +0100 Subject: [PATCH 0095/1342] profile: Suppress warning about large allocations when profile=1 is specified When profile= is used, a large buffer is allocated early at boot. This can be larger than what the page allocator can provide so it prints a warning. However, the caller is able to handle the situation so this patch suppresses the warning. Signed-off-by: Mel Gorman Reviewed-by: KOSAKI Motohiro Cc: Linux Memory Management List Cc: Heinz Diehl Cc: David Miller Cc: Arnaldo Carvalho de Melo Cc: Mel Gorman Cc: Andrew Morton LKML-Reference: <1247656992-19846-3-git-send-email-mel@csn.ul.ie> Signed-off-by: Ingo Molnar --- kernel/profile.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/kernel/profile.c b/kernel/profile.c index 69911b5745e..419250ebec4 100644 --- a/kernel/profile.c +++ b/kernel/profile.c @@ -117,11 +117,12 @@ int __ref profile_init(void) cpumask_copy(prof_cpu_mask, cpu_possible_mask); - prof_buffer = kzalloc(buffer_bytes, GFP_KERNEL); + prof_buffer = kzalloc(buffer_bytes, GFP_KERNEL|__GFP_NOWARN); if (prof_buffer) return 0; - prof_buffer = alloc_pages_exact(buffer_bytes, GFP_KERNEL|__GFP_ZERO); + prof_buffer = alloc_pages_exact(buffer_bytes, + GFP_KERNEL|__GFP_ZERO|__GFP_NOWARN); if (prof_buffer) return 0; -- GitLab From 6aa542a694dc9ea4344a8a590d2628c33d1b9431 Mon Sep 17 00:00:00 2001 From: Alexey Fisher Date: Wed, 15 Jul 2009 14:16:09 +0200 Subject: [PATCH 0096/1342] x86: Add quirk for Intel DG45ID board to avoid low memory corruption AMI BIOS with low memory corruption was found on Intel DG45ID board (Bug 13710). Add this board to the blacklist - in the (somewhat optimistic) hope of future boards/BIOSes from Intel not having this bug. Also see: http://bugzilla.kernel.org/show_bug.cgi?id=13736 Signed-off-by: Alexey Fisher Cc: ykzhao Cc: alan@lxorguk.ukuu.org.uk Cc: LKML-Reference: <1247660169-4503-1-git-send-email-bug-track@fisher-privat.net> Signed-off-by: Ingo Molnar --- arch/x86/kernel/setup.c | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/x86/kernel/setup.c b/arch/x86/kernel/setup.c index de2cab13284..63f32d220ef 100644 --- a/arch/x86/kernel/setup.c +++ b/arch/x86/kernel/setup.c @@ -672,6 +672,19 @@ static struct dmi_system_id __initdata bad_bios_dmi_table[] = { DMI_MATCH(DMI_BIOS_VENDOR, "Phoenix Technologies"), }, }, + { + /* + * AMI BIOS with low memory corruption was found on Intel DG45ID board. + * It hase different DMI_BIOS_VENDOR = "Intel Corp.", for now we will + * match only DMI_BOARD_NAME and see if there is more bad products + * with this vendor. + */ + .callback = dmi_low_memory_corruption, + .ident = "AMI BIOS", + .matches = { + DMI_MATCH(DMI_BOARD_NAME, "DG45ID"), + }, + }, #endif {} }; -- GitLab From 8bcdbe427924a1e4b4e4cf68020e92e9f93fe011 Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Tue, 14 Jul 2009 10:52:55 +0100 Subject: [PATCH 0097/1342] x86: Include all of .data.* sections in _edata on 64-bit The .data.read_mostly and .data.cacheline_aligned sections aren't covered by the _sdata .. _edata range on x86-64. This affects kmemleak reporting leading to possible false positives by not scanning the whole data section. Signed-off-by: Catalin Marinas Tested-by: Alexey Fisher Acked-by: Sam Ravnborg Cc: Pekka Enberg LKML-Reference: <1247565175.28240.37.camel@pc1117.cambridge.arm.com> Signed-off-by: Ingo Molnar Cc: Sam Ravnborg --- arch/x86/kernel/vmlinux.lds.S | 7 ------- 1 file changed, 7 deletions(-) diff --git a/arch/x86/kernel/vmlinux.lds.S b/arch/x86/kernel/vmlinux.lds.S index 367e8788204..59f31d2dd43 100644 --- a/arch/x86/kernel/vmlinux.lds.S +++ b/arch/x86/kernel/vmlinux.lds.S @@ -112,11 +112,6 @@ SECTIONS _sdata = .; DATA_DATA CONSTRUCTORS - -#ifdef CONFIG_X86_64 - /* End of data section */ - _edata = .; -#endif } :data #ifdef CONFIG_X86_32 @@ -156,10 +151,8 @@ SECTIONS .data.read_mostly : AT(ADDR(.data.read_mostly) - LOAD_OFFSET) { *(.data.read_mostly) -#ifdef CONFIG_X86_32 /* End of data section */ _edata = .; -#endif } #ifdef CONFIG_X86_64 -- GitLab From a468d389349a7560249b355cdb6d2097ea1616c9 Mon Sep 17 00:00:00 2001 From: Thomas Gleixner Date: Fri, 17 Jul 2009 14:15:46 +0200 Subject: [PATCH 0098/1342] sched: fix load average accounting vs. cpu hotplug The new load average code clears rq->calc_load_active on CPU_ONLINE. That's wrong as the new onlined CPU might have got a scheduler tick already and accounted the delta to the stale value of the time we offlined the CPU. Clear the value when we cleanup the dead CPU instead. Also move the update of the calc_load_update time for the newly online CPU to CPU_UP_PREPARE to avoid that the CPU plays catch up with the stale update time value. Signed-off-by: Thomas Gleixner --- kernel/sched.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/kernel/sched.c b/kernel/sched.c index 98972d366fd..1b59e265273 100644 --- a/kernel/sched.c +++ b/kernel/sched.c @@ -7289,6 +7289,7 @@ static void migrate_dead_tasks(unsigned int dead_cpu) static void calc_global_load_remove(struct rq *rq) { atomic_long_sub(rq->calc_load_active, &calc_load_tasks); + rq->calc_load_active = 0; } #endif /* CONFIG_HOTPLUG_CPU */ @@ -7515,6 +7516,7 @@ migration_call(struct notifier_block *nfb, unsigned long action, void *hcpu) task_rq_unlock(rq, &flags); get_task_struct(p); cpu_rq(cpu)->migration_thread = p; + rq->calc_load_update = calc_load_update; break; case CPU_ONLINE: @@ -7525,8 +7527,6 @@ migration_call(struct notifier_block *nfb, unsigned long action, void *hcpu) /* Update our root-domain */ rq = cpu_rq(cpu); spin_lock_irqsave(&rq->lock, flags); - rq->calc_load_update = calc_load_update; - rq->calc_load_active = 0; if (rq->rd) { BUG_ON(!cpumask_test_cpu(cpu, rq->rd->span)); -- GitLab From 6301cb95c119ebf324bb96ee226fa9ddffad80a7 Mon Sep 17 00:00:00 2001 From: Thomas Gleixner Date: Fri, 17 Jul 2009 14:15:47 +0200 Subject: [PATCH 0099/1342] sched: fix nr_uninterruptible accounting of frozen tasks really commit e3c8ca8336 (sched: do not count frozen tasks toward load) broke the nr_uninterruptible accounting on freeze/thaw. On freeze the task is excluded from accounting with a check for (task->flags & PF_FROZEN), but that flag is cleared before the task is thawed. So while we prevent that the task with state TASK_UNINTERRUPTIBLE is accounted to nr_uninterruptible on freeze we decrement nr_uninterruptible on thaw. Use a separate flag which is handled by the freezing task itself. Set it before calling the scheduler with TASK_UNINTERRUPTIBLE state and clear it after we return from frozen state. Cc: Signed-off-by: Thomas Gleixner --- include/linux/sched.h | 3 ++- kernel/freezer.c | 7 +++++++ 2 files changed, 9 insertions(+), 1 deletion(-) diff --git a/include/linux/sched.h b/include/linux/sched.h index 16a982e389f..3ab08e4bb6b 100644 --- a/include/linux/sched.h +++ b/include/linux/sched.h @@ -209,7 +209,7 @@ extern unsigned long long time_sync_thresh; ((task->state & (__TASK_STOPPED | __TASK_TRACED)) != 0) #define task_contributes_to_load(task) \ ((task->state & TASK_UNINTERRUPTIBLE) != 0 && \ - (task->flags & PF_FROZEN) == 0) + (task->flags & PF_FREEZING) == 0) #define __set_task_state(tsk, state_value) \ do { (tsk)->state = (state_value); } while (0) @@ -1680,6 +1680,7 @@ extern cputime_t task_gtime(struct task_struct *p); #define PF_MEMALLOC 0x00000800 /* Allocating memory */ #define PF_FLUSHER 0x00001000 /* responsible for disk writeback */ #define PF_USED_MATH 0x00002000 /* if unset the fpu must be initialized before use */ +#define PF_FREEZING 0x00004000 /* freeze in progress. do not account to load */ #define PF_NOFREEZE 0x00008000 /* this thread should not be frozen */ #define PF_FROZEN 0x00010000 /* frozen for system suspend */ #define PF_FSTRANS 0x00020000 /* inside a filesystem transaction */ diff --git a/kernel/freezer.c b/kernel/freezer.c index 2f4936cf708..bd1d42b17cb 100644 --- a/kernel/freezer.c +++ b/kernel/freezer.c @@ -44,12 +44,19 @@ void refrigerator(void) recalc_sigpending(); /* We sent fake signal, clean it up */ spin_unlock_irq(¤t->sighand->siglock); + /* prevent accounting of that task to load */ + current->flags |= PF_FREEZING; + for (;;) { set_current_state(TASK_UNINTERRUPTIBLE); if (!frozen(current)) break; schedule(); } + + /* Remove the accounting blocker */ + current->flags &= ~PF_FREEZING; + pr_debug("%s left refrigerator\n", current->comm); __set_current_state(save); } -- GitLab From 4841158b26e28e1476eed84c7347c18f11317750 Mon Sep 17 00:00:00 2001 From: Pavel Roskin Date: Sat, 18 Jul 2009 16:46:02 -0400 Subject: [PATCH 0100/1342] timer: Avoid reading uninitialized data timer->expires may be uninitialized, so check timer_pending() before touching timer->expires to pacify kmemcheck. Signed-off-by: Pavel Roskin LKML-Reference: <20090718204602.5191.360.stgit@mj.roinet.com> Signed-off-by: Thomas Gleixner --- kernel/timer.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/timer.c b/kernel/timer.c index 0b36b9e5cc8..a7f07d5a624 100644 --- a/kernel/timer.c +++ b/kernel/timer.c @@ -714,7 +714,7 @@ int mod_timer(struct timer_list *timer, unsigned long expires) * networking code - if the timer is re-modified * to be the same thing then just return: */ - if (timer->expires == expires && timer_pending(timer)) + if (timer_pending(timer) && timer->expires == expires) return 1; return __mod_timer(timer, expires, false, TIMER_NOT_PINNED); -- GitLab From 4fbfff76079a5c0e1751b0ddf53160d33f7831e7 Mon Sep 17 00:00:00 2001 From: Rakib Mullick Date: Fri, 17 Jul 2009 20:13:22 +0600 Subject: [PATCH 0101/1342] virtio_blk: mark virtio_blk with __refdata to kill spurious section mismatch The variable virtio_blk references the function virtblk_probe() (which is in .devinit section) and also references the function virtblk_remove() ( which is in .devexit section). So, virtio_blk simultaneously refers .devinit and .devexit section. To avoid this messup, we mark virtio_blk as __refdata. We were warned by the following warning: LD drivers/block/built-in.o WARNING: drivers/block/built-in.o(.data+0xc8dc): Section mismatch in reference from the variable virtio_blk to the function .devinit.text:virtblk_probe() The variable virtio_blk references the function __devinit virtblk_probe() If the reference is valid then annotate the variable with __init* or __refdata (see linux/init.h) or name the variable: *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, WARNING: drivers/block/built-in.o(.data+0xc8e0): Section mismatch in reference from the variable virtio_blk to the function .devexit.text:virtblk_remove() The variable virtio_blk references the function __devexit virtblk_remove() If the reference is valid then annotate the variable with __exit* (see linux/init.h) or name the variable: *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, Signed-off-by: Rakib Mullick Signed-off-by: Tejun Heo --- drivers/block/virtio_blk.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/drivers/block/virtio_blk.c b/drivers/block/virtio_blk.c index 43db3ea15b5..024f2d29258 100644 --- a/drivers/block/virtio_blk.c +++ b/drivers/block/virtio_blk.c @@ -424,7 +424,12 @@ static unsigned int features[] = { VIRTIO_BLK_F_SCSI, VIRTIO_BLK_F_IDENTIFY }; -static struct virtio_driver virtio_blk = { +/* + * virtio_blk causes spurious section mismatch warning by + * simultaneously referring to a __devinit and a __devexit function. + * Use __refdata to avoid this warning. + */ +static struct virtio_driver __refdata virtio_blk = { .feature_table = features, .feature_table_size = ARRAY_SIZE(features), .driver.name = KBUILD_MODNAME, -- GitLab From 2e9bf247066a293ebcd4672ddd487808ab5f2d1b Mon Sep 17 00:00:00 2001 From: Jaroslav Kysela Date: Sat, 18 Jul 2009 11:48:19 +0200 Subject: [PATCH 0102/1342] ALSA: hda_codec: Check for invalid zero connections To prevent "Too many connections" message and the error path for some HDMI codecs (which makes onboard audio unusable), check for invalid zero connections for CONNECT_LIST verb. Signed-off-by: Jaroslav Kysela Signed-off-by: Takashi Iwai --- sound/pci/hda/hda_codec.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/sound/pci/hda/hda_codec.c b/sound/pci/hda/hda_codec.c index 26d255de6be..88480c0c58a 100644 --- a/sound/pci/hda/hda_codec.c +++ b/sound/pci/hda/hda_codec.c @@ -332,6 +332,12 @@ int snd_hda_get_connections(struct hda_codec *codec, hda_nid_t nid, AC_VERB_GET_CONNECT_LIST, i); range_val = !!(parm & (1 << (shift-1))); /* ranges */ val = parm & mask; + if (val == 0) { + snd_printk(KERN_WARNING "hda_codec: " + "invalid CONNECT_LIST verb %x[%i]:%x\n", + nid, i, parm); + return 0; + } parm >>= shift; if (range_val) { /* ranges between the previous and this one */ -- GitLab From fcb2954b9621dfeaca92f6a11dac69cfdfaa6705 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Sat, 18 Jul 2009 17:26:14 +0200 Subject: [PATCH 0103/1342] ALSA: sound/isa: convert nested spin_lock_irqsave to spin_lock If spin_lock_irqsave is called twice in a row with the same second argument, the interrupt state at the point of the second call overwrites the value saved by the first call. Indeed, the second call does not need to save the interrupt state, so it is changed to a simple spin_lock. The semantic match that finds this problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // @@ expression lock1,lock2; expression flags; @@ *spin_lock_irqsave(lock1,flags) ... when != flags *spin_lock_irqsave(lock2,flags) // Signed-off-by: Julia Lawall Signed-off-by: Takashi Iwai --- sound/isa/gus/gus_pcm.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/sound/isa/gus/gus_pcm.c b/sound/isa/gus/gus_pcm.c index edb11eefdfe..2dcf45bf729 100644 --- a/sound/isa/gus/gus_pcm.c +++ b/sound/isa/gus/gus_pcm.c @@ -795,13 +795,13 @@ static int snd_gf1_pcm_volume_put(struct snd_kcontrol *kcontrol, struct snd_ctl_ if (!(pcmp->flags & SNDRV_GF1_PCM_PFLG_ACTIVE)) continue; /* load real volume - better precision */ - spin_lock_irqsave(&gus->reg_lock, flags); + spin_lock(&gus->reg_lock); snd_gf1_select_voice(gus, pvoice->number); snd_gf1_ctrl_stop(gus, SNDRV_GF1_VB_VOLUME_CONTROL); vol = pvoice == pcmp->pvoices[0] ? gus->gf1.pcm_volume_level_left : gus->gf1.pcm_volume_level_right; snd_gf1_write16(gus, SNDRV_GF1_VW_VOLUME, vol); pcmp->final_volume = 1; - spin_unlock_irqrestore(&gus->reg_lock, flags); + spin_unlock(&gus->reg_lock); } spin_unlock_irqrestore(&gus->voice_alloc, flags); return change; -- GitLab From 79ef2bb01445400def20c7993b27fbcad27ca95f Mon Sep 17 00:00:00 2001 From: Thomas Gleixner Date: Sun, 19 Jul 2009 17:09:12 +0200 Subject: [PATCH 0104/1342] clocksource: Prevent NULL pointer dereference Writing a zero length string to sys/.../current_clocksource will cause a NULL pointer dereference if the clock events system is in one shot (highres or nohz) mode. Pointed-out-by: Dan Carpenter LKML-Reference: Signed-off-by: Thomas Gleixner --- kernel/time/clocksource.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/time/clocksource.c b/kernel/time/clocksource.c index 592bf584d1d..7466cb81125 100644 --- a/kernel/time/clocksource.c +++ b/kernel/time/clocksource.c @@ -513,7 +513,7 @@ static ssize_t sysfs_override_clocksource(struct sys_device *dev, * Check to make sure we don't switch to a non-highres capable * clocksource if the tick code is in oneshot mode (highres or nohz) */ - if (tick_oneshot_mode_active() && + if (tick_oneshot_mode_active() && ovr && !(ovr->flags & CLOCK_SOURCE_VALID_FOR_HRES)) { printk(KERN_WARNING "%s clocksource is not HRT compatible. " "Cannot switch while in HRT/NOHZ mode\n", ovr->name); -- GitLab From f96e0808212ca284cc9398d7cd3f573786c1d890 Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Sun, 19 Jul 2009 21:58:34 +0530 Subject: [PATCH 0105/1342] ALSA: OSS sequencer should be initialized after snd_seq_system_client_init When build SND_SEQUENCER in kernel then OSS sequencer(alsa_seq_oss_init) is initialized before System (snd_seq_system_client_init) which leads to memory leak : unreferenced object 0xf6b0e680 (size 256): comm "swapper", pid 1, jiffies 4294670753 backtrace: [] create_object+0x135/0x204 [] kmemleak_alloc+0x26/0x4c [] kmem_cache_alloc+0x72/0xff [] seq_create_client1+0x22/0x160 [] snd_seq_create_kernel_client+0x72/0xef [] snd_seq_oss_create_client+0x86/0x142 [] alsa_seq_oss_init+0xf6/0x155 [] do_one_initcall+0x4f/0x111 [] kernel_init+0x115/0x166 [] kernel_thread_helper+0x7/0x10 [] 0xffffffff unreferenced object 0xf688a580 (size 64): comm "swapper", pid 1, jiffies 4294670753 backtrace: [] create_object+0x135/0x204 [] kmemleak_alloc+0x26/0x4c [] kmem_cache_alloc+0x72/0xff [] snd_seq_pool_new+0x1c/0xb8 [] seq_create_client1+0x87/0x160 [] snd_seq_create_kernel_client+0x72/0xef [] snd_seq_oss_create_client+0x86/0x142 [] alsa_seq_oss_init+0xf6/0x155 [] do_one_initcall+0x4f/0x111 [] kernel_init+0x115/0x166 [] kernel_thread_helper+0x7/0x10 [] 0xffffffff unreferenced object 0xf6b0e480 (size 256): comm "swapper", pid 1, jiffies 4294670754 backtrace: [] create_object+0x135/0x204 [] kmemleak_alloc+0x26/0x4c [] kmem_cache_alloc+0x72/0xff [] snd_seq_create_port+0x51/0x21c [] snd_seq_ioctl_create_port+0x57/0x13c [] snd_seq_do_ioctl+0x4a/0x69 [] snd_seq_kernel_client_ctl+0x33/0x49 [] snd_seq_oss_create_client+0xf5/0x142 [] alsa_seq_oss_init+0xf6/0x155 [] do_one_initcall+0x4f/0x111 [] kernel_init+0x115/0x166 [] kernel_thread_helper+0x7/0x10 [] 0xffffffff The correct order should be : System (snd_seq_system_client_init) should be initialized before OSS sequencer(alsa_seq_oss_init) which is equivalent to : 1. insmod sound/core/seq/snd-seq-device.ko 2. insmod sound/core/seq/snd-seq.ko 3. insmod sound/core/seq/snd-seq-midi-event.ko 4. insmod sound/core/seq/oss/snd-seq-oss.ko Including sound/core/seq/oss/Makefile after other seq modules fixes the ordering and memory leak. Signed-off-by: Jaswinder Singh Rajput Signed-off-by: Takashi Iwai --- sound/core/seq/Makefile | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-) diff --git a/sound/core/seq/Makefile b/sound/core/seq/Makefile index 1bcb360330e..941f64a853e 100644 --- a/sound/core/seq/Makefile +++ b/sound/core/seq/Makefile @@ -3,10 +3,6 @@ # Copyright (c) 1999 by Jaroslav Kysela # -ifeq ($(CONFIG_SND_SEQUENCER_OSS),y) - obj-$(CONFIG_SND_SEQUENCER) += oss/ -endif - snd-seq-device-objs := seq_device.o snd-seq-objs := seq.o seq_lock.o seq_clientmgr.o seq_memory.o seq_queue.o \ seq_fifo.o seq_prioq.o seq_timer.o \ @@ -19,7 +15,8 @@ snd-seq-virmidi-objs := seq_virmidi.o obj-$(CONFIG_SND_SEQUENCER) += snd-seq.o snd-seq-device.o ifeq ($(CONFIG_SND_SEQUENCER_OSS),y) -obj-$(CONFIG_SND_SEQUENCER) += snd-seq-midi-event.o + obj-$(CONFIG_SND_SEQUENCER) += snd-seq-midi-event.o + obj-$(CONFIG_SND_SEQUENCER) += oss/ endif obj-$(CONFIG_SND_SEQ_DUMMY) += snd-seq-dummy.o -- GitLab From 76c317d6e5cb7f58541879006d39774596962715 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Sun, 19 Jul 2009 17:26:13 +0200 Subject: [PATCH 0106/1342] HID: Move dereferences below a NULL test If the NULL test is necessary, then the dereferences should be moved below the NULL test. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // @@ type T; expression E,E1; identifier i,fld; statement S; @@ - T i = E->fld; + T i; ... when != E=E1 when != i if (E == NULL||...) S + i = E->fld; // Signed-off-by: Julia Lawall Signed-off-by: Jiri Kosina --- drivers/hid/hid-core.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/hid/hid-core.c b/drivers/hid/hid-core.c index f2c21d5d24e..5eb10c2ce66 100644 --- a/drivers/hid/hid-core.c +++ b/drivers/hid/hid-core.c @@ -1075,14 +1075,16 @@ EXPORT_SYMBOL_GPL(hid_report_raw_event); */ int hid_input_report(struct hid_device *hid, int type, u8 *data, int size, int interrupt) { - struct hid_report_enum *report_enum = hid->report_enum + type; - struct hid_driver *hdrv = hid->driver; + struct hid_report_enum *report_enum; + struct hid_driver *hdrv; struct hid_report *report; unsigned int i; int ret; if (!hid || !hid->driver) return -ENODEV; + report_enum = hid->report_enum + type; + hdrv = hid->driver; if (!size) { dbg_hid("empty report\n"); -- GitLab From 42b95f0c6b524b5a670dd17533a3522db368f600 Mon Sep 17 00:00:00 2001 From: Hao Song Date: Mon, 20 Jul 2009 15:01:16 +0800 Subject: [PATCH 0107/1342] ALSA: hda - Add quirk for Gateway T6834c laptop Gateway T6834c laptops need EAPD always on while the default behavior for the STAC9205 reference board is to turn it off upon every HP plug. By using the special "eapd" model, which is first introduced for Gateway T1616 laptops for this same reason, this peculiarity can be properly handled. Signed-off-by: Hao Song Cc: Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_sigmatel.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/pci/hda/patch_sigmatel.c b/sound/pci/hda/patch_sigmatel.c index 41b5b3a18c1..d9b89ba2b65 100644 --- a/sound/pci/hda/patch_sigmatel.c +++ b/sound/pci/hda/patch_sigmatel.c @@ -2378,6 +2378,7 @@ static struct snd_pci_quirk stac9205_cfg_tbl[] = { SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x0228, "Dell Vostro 1500", STAC_9205_DELL_M42), /* Gateway */ + SND_PCI_QUIRK(0x107b, 0x0560, "Gateway T6834c", STAC_9205_EAPD), SND_PCI_QUIRK(0x107b, 0x0565, "Gateway T1616", STAC_9205_EAPD), {} /* terminator */ }; -- GitLab From b04add956616b6d89ff21da749b46ad2bd58ef32 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Mon, 20 Jul 2009 08:01:36 +0200 Subject: [PATCH 0108/1342] ALSA: hda - Fix pin-setup for Sony VAIO with STAC9872 codecs The recent rewrite of the codec parser for STAC9872 caused a regression for some Sony VAIO models that don't give proper pin default configs by BIOS. Even using model=vaio doesn't work because the pin definitions are set after the pin overrides. This patch fixes the pin definitions in patch_stac9872() to be put in the right place before the pin overrides. Also the patch adds the new quirk entry for VAIO F/S to have the correct pin default configs. Signed-off-by: Takashi Iwai Cc: --- sound/pci/hda/patch_sigmatel.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/sound/pci/hda/patch_sigmatel.c b/sound/pci/hda/patch_sigmatel.c index d9b89ba2b65..da7f9f65c04 100644 --- a/sound/pci/hda/patch_sigmatel.c +++ b/sound/pci/hda/patch_sigmatel.c @@ -5855,6 +5855,8 @@ static unsigned int *stac9872_brd_tbl[STAC_9872_MODELS] = { }; static struct snd_pci_quirk stac9872_cfg_tbl[] = { + SND_PCI_QUIRK_MASK(0x104d, 0xfff0, 0x81e0, + "Sony VAIO F/S", STAC_9872_VAIO), {} /* terminator */ }; @@ -5867,6 +5869,8 @@ static int patch_stac9872(struct hda_codec *codec) if (spec == NULL) return -ENOMEM; codec->spec = spec; + spec->num_pins = ARRAY_SIZE(stac9872_pin_nids); + spec->pin_nids = stac9872_pin_nids; spec->board_config = snd_hda_check_board_config(codec, STAC_9872_MODELS, stac9872_models, @@ -5878,8 +5882,6 @@ static int patch_stac9872(struct hda_codec *codec) stac92xx_set_config_regs(codec, stac9872_brd_tbl[spec->board_config]); - spec->num_pins = ARRAY_SIZE(stac9872_pin_nids); - spec->pin_nids = stac9872_pin_nids; spec->multiout.dac_nids = spec->dac_nids; spec->num_adcs = ARRAY_SIZE(stac9872_adc_nids); spec->adc_nids = stac9872_adc_nids; -- GitLab From 34fdeb2d07102e07ecafe79dec170bd6733f2e56 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Mon, 20 Jul 2009 15:42:51 +0200 Subject: [PATCH 0109/1342] ALSA: ca0106 - Fix the max capture buffer size The capture buffer size with 64kB seems broken with CA0106. At least, either the update timing or the DMA position is wrong, and this screws up pulseaudio badly. This patch restricts the max buffer size less than that to make life a bit easier. Signed-off-by: Takashi Iwai Cc: --- sound/pci/ca0106/ca0106_main.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/sound/pci/ca0106/ca0106_main.c b/sound/pci/ca0106/ca0106_main.c index 57b992a5c05..700f15ea16d 100644 --- a/sound/pci/ca0106/ca0106_main.c +++ b/sound/pci/ca0106/ca0106_main.c @@ -325,9 +325,9 @@ static struct snd_pcm_hardware snd_ca0106_capture_hw = { .rate_max = 192000, .channels_min = 2, .channels_max = 2, - .buffer_bytes_max = ((65536 - 64) * 8), + .buffer_bytes_max = 65536 - 128, .period_bytes_min = 64, - .period_bytes_max = (65536 - 64), + .period_bytes_max = 32768 - 64, .periods_min = 2, .periods_max = 2, .fifo_size = 0, -- GitLab From a50a97d415d839e6db9df288ff0205528e52c03e Mon Sep 17 00:00:00 2001 From: Wan ZongShun Date: Thu, 16 Jul 2009 02:55:05 +0000 Subject: [PATCH 0110/1342] Add mac driver for w90p910 Add mac driver support for evaluation board based on w90p910. Signed-off-by: Wan ZongShun Signed-off-by: David S. Miller --- drivers/net/arm/Kconfig | 8 + drivers/net/arm/Makefile | 1 + drivers/net/arm/w90p910_ether.c | 1105 +++++++++++++++++++++++++++++++ 3 files changed, 1114 insertions(+) create mode 100644 drivers/net/arm/w90p910_ether.c diff --git a/drivers/net/arm/Kconfig b/drivers/net/arm/Kconfig index 2895db13bfa..c37ee9e6b67 100644 --- a/drivers/net/arm/Kconfig +++ b/drivers/net/arm/Kconfig @@ -63,3 +63,11 @@ config IXP4XX_ETH help Say Y here if you want to use built-in Ethernet ports on IXP4xx processor. + +config W90P910_ETH + tristate "Nuvoton w90p910 Ethernet support" + depends on ARM && ARCH_W90X900 + select PHYLIB + help + Say Y here if you want to use built-in Ethernet ports + on w90p910 processor. diff --git a/drivers/net/arm/Makefile b/drivers/net/arm/Makefile index 811a3ccd14c..303171f589e 100644 --- a/drivers/net/arm/Makefile +++ b/drivers/net/arm/Makefile @@ -11,3 +11,4 @@ obj-$(CONFIG_ARM_AT91_ETHER) += at91_ether.o obj-$(CONFIG_ARM_KS8695_ETHER) += ks8695net.o obj-$(CONFIG_EP93XX_ETH) += ep93xx_eth.o obj-$(CONFIG_IXP4XX_ETH) += ixp4xx_eth.o +obj-$(CONFIG_W90P910_ETH) += w90p910_ether.o diff --git a/drivers/net/arm/w90p910_ether.c b/drivers/net/arm/w90p910_ether.c new file mode 100644 index 00000000000..616fb7985a3 --- /dev/null +++ b/drivers/net/arm/w90p910_ether.c @@ -0,0 +1,1105 @@ +/* + * Copyright (c) 2008-2009 Nuvoton technology corporation. + * + * Wan ZongShun + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation;version 2 of the License. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define DRV_MODULE_NAME "w90p910-emc" +#define DRV_MODULE_VERSION "0.1" + +/* Ethernet MAC Registers */ +#define REG_CAMCMR 0x00 +#define REG_CAMEN 0x04 +#define REG_CAMM_BASE 0x08 +#define REG_CAML_BASE 0x0c +#define REG_TXDLSA 0x88 +#define REG_RXDLSA 0x8C +#define REG_MCMDR 0x90 +#define REG_MIID 0x94 +#define REG_MIIDA 0x98 +#define REG_FFTCR 0x9C +#define REG_TSDR 0xa0 +#define REG_RSDR 0xa4 +#define REG_DMARFC 0xa8 +#define REG_MIEN 0xac +#define REG_MISTA 0xb0 +#define REG_CTXDSA 0xcc +#define REG_CTXBSA 0xd0 +#define REG_CRXDSA 0xd4 +#define REG_CRXBSA 0xd8 + +/* mac controller bit */ +#define MCMDR_RXON 0x01 +#define MCMDR_ACP (0x01 << 3) +#define MCMDR_SPCRC (0x01 << 5) +#define MCMDR_TXON (0x01 << 8) +#define MCMDR_FDUP (0x01 << 18) +#define MCMDR_ENMDC (0x01 << 19) +#define MCMDR_OPMOD (0x01 << 20) +#define SWR (0x01 << 24) + +/* cam command regiser */ +#define CAMCMR_AUP 0x01 +#define CAMCMR_AMP (0x01 << 1) +#define CAMCMR_ABP (0x01 << 2) +#define CAMCMR_CCAM (0x01 << 3) +#define CAMCMR_ECMP (0x01 << 4) +#define CAM0EN 0x01 + +/* mac mii controller bit */ +#define MDCCR (0x0a << 20) +#define PHYAD (0x01 << 8) +#define PHYWR (0x01 << 16) +#define PHYBUSY (0x01 << 17) +#define PHYPRESP (0x01 << 18) +#define CAM_ENTRY_SIZE 0x08 + +/* rx and tx status */ +#define TXDS_TXCP (0x01 << 19) +#define RXDS_CRCE (0x01 << 17) +#define RXDS_PTLE (0x01 << 19) +#define RXDS_RXGD (0x01 << 20) +#define RXDS_ALIE (0x01 << 21) +#define RXDS_RP (0x01 << 22) + +/* mac interrupt status*/ +#define MISTA_EXDEF (0x01 << 19) +#define MISTA_TXBERR (0x01 << 24) +#define MISTA_TDU (0x01 << 23) +#define MISTA_RDU (0x01 << 10) +#define MISTA_RXBERR (0x01 << 11) + +#define ENSTART 0x01 +#define ENRXINTR 0x01 +#define ENRXGD (0x01 << 4) +#define ENRXBERR (0x01 << 11) +#define ENTXINTR (0x01 << 16) +#define ENTXCP (0x01 << 18) +#define ENTXABT (0x01 << 21) +#define ENTXBERR (0x01 << 24) +#define ENMDC (0x01 << 19) +#define PHYBUSY (0x01 << 17) +#define MDCCR_VAL 0xa00000 + +/* rx and tx owner bit */ +#define RX_OWEN_DMA (0x01 << 31) +#define RX_OWEN_CPU (~(0x03 << 30)) +#define TX_OWEN_DMA (0x01 << 31) +#define TX_OWEN_CPU (~(0x01 << 31)) + +/* tx frame desc controller bit */ +#define MACTXINTEN 0x04 +#define CRCMODE 0x02 +#define PADDINGMODE 0x01 + +/* fftcr controller bit */ +#define TXTHD (0x03 << 8) +#define BLENGTH (0x01 << 20) + +/* global setting for driver */ +#define RX_DESC_SIZE 50 +#define TX_DESC_SIZE 10 +#define MAX_RBUFF_SZ 0x600 +#define MAX_TBUFF_SZ 0x600 +#define TX_TIMEOUT 50 +#define DELAY 1000 +#define CAM0 0x0 + +static int w90p910_mdio_read(struct net_device *dev, int phy_id, int reg); + +struct w90p910_rxbd { + unsigned int sl; + unsigned int buffer; + unsigned int reserved; + unsigned int next; +}; + +struct w90p910_txbd { + unsigned int mode; + unsigned int buffer; + unsigned int sl; + unsigned int next; +}; + +struct recv_pdesc { + struct w90p910_rxbd desclist[RX_DESC_SIZE]; + char recv_buf[RX_DESC_SIZE][MAX_RBUFF_SZ]; +}; + +struct tran_pdesc { + struct w90p910_txbd desclist[TX_DESC_SIZE]; + char tran_buf[RX_DESC_SIZE][MAX_TBUFF_SZ]; +}; + +struct w90p910_ether { + struct recv_pdesc *rdesc; + struct recv_pdesc *rdesc_phys; + struct tran_pdesc *tdesc; + struct tran_pdesc *tdesc_phys; + struct net_device_stats stats; + struct platform_device *pdev; + struct sk_buff *skb; + struct clk *clk; + struct clk *rmiiclk; + struct mii_if_info mii; + struct timer_list check_timer; + void __iomem *reg; + unsigned int rxirq; + unsigned int txirq; + unsigned int cur_tx; + unsigned int cur_rx; + unsigned int finish_tx; + unsigned int rx_packets; + unsigned int rx_bytes; + unsigned int start_tx_ptr; + unsigned int start_rx_ptr; + unsigned int linkflag; + spinlock_t lock; +}; + +static void update_linkspeed_register(struct net_device *dev, + unsigned int speed, unsigned int duplex) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int val; + + val = __raw_readl(ether->reg + REG_MCMDR); + + if (speed == SPEED_100) { + /* 100 full/half duplex */ + if (duplex == DUPLEX_FULL) { + val |= (MCMDR_OPMOD | MCMDR_FDUP); + } else { + val |= MCMDR_OPMOD; + val &= ~MCMDR_FDUP; + } + } else { + /* 10 full/half duplex */ + if (duplex == DUPLEX_FULL) { + val |= MCMDR_FDUP; + val &= ~MCMDR_OPMOD; + } else { + val &= ~(MCMDR_FDUP | MCMDR_OPMOD); + } + } + + __raw_writel(val, ether->reg + REG_MCMDR); +} + +static void update_linkspeed(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + struct platform_device *pdev; + unsigned int bmsr, bmcr, lpa, speed, duplex; + + pdev = ether->pdev; + + if (!mii_link_ok(ðer->mii)) { + ether->linkflag = 0x0; + netif_carrier_off(dev); + dev_warn(&pdev->dev, "%s: Link down.\n", dev->name); + return; + } + + if (ether->linkflag == 1) + return; + + bmsr = w90p910_mdio_read(dev, ether->mii.phy_id, MII_BMSR); + bmcr = w90p910_mdio_read(dev, ether->mii.phy_id, MII_BMCR); + + if (bmcr & BMCR_ANENABLE) { + if (!(bmsr & BMSR_ANEGCOMPLETE)) + return; + + lpa = w90p910_mdio_read(dev, ether->mii.phy_id, MII_LPA); + + if ((lpa & LPA_100FULL) || (lpa & LPA_100HALF)) + speed = SPEED_100; + else + speed = SPEED_10; + + if ((lpa & LPA_100FULL) || (lpa & LPA_10FULL)) + duplex = DUPLEX_FULL; + else + duplex = DUPLEX_HALF; + + } else { + speed = (bmcr & BMCR_SPEED100) ? SPEED_100 : SPEED_10; + duplex = (bmcr & BMCR_FULLDPLX) ? DUPLEX_FULL : DUPLEX_HALF; + } + + update_linkspeed_register(dev, speed, duplex); + + dev_info(&pdev->dev, "%s: Link now %i-%s\n", dev->name, speed, + (duplex == DUPLEX_FULL) ? "FullDuplex" : "HalfDuplex"); + ether->linkflag = 0x01; + + netif_carrier_on(dev); +} + +static void w90p910_check_link(unsigned long dev_id) +{ + struct net_device *dev = (struct net_device *) dev_id; + struct w90p910_ether *ether = netdev_priv(dev); + + update_linkspeed(dev); + mod_timer(ðer->check_timer, jiffies + msecs_to_jiffies(1000)); +} + +static void w90p910_write_cam(struct net_device *dev, + unsigned int x, unsigned char *pval) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int msw, lsw; + + msw = (pval[0] << 24) | (pval[1] << 16) | (pval[2] << 8) | pval[3]; + + lsw = (pval[4] << 24) | (pval[5] << 16); + + __raw_writel(lsw, ether->reg + REG_CAML_BASE + x * CAM_ENTRY_SIZE); + __raw_writel(msw, ether->reg + REG_CAMM_BASE + x * CAM_ENTRY_SIZE); +} + +static void w90p910_init_desc(struct net_device *dev) +{ + struct w90p910_ether *ether; + struct w90p910_txbd *tdesc, *tdesc_phys; + struct w90p910_rxbd *rdesc, *rdesc_phys; + unsigned int i, j; + + ether = netdev_priv(dev); + + ether->tdesc = (struct tran_pdesc *) + dma_alloc_coherent(NULL, sizeof(struct tran_pdesc), + (dma_addr_t *) ðer->tdesc_phys, GFP_KERNEL); + + ether->rdesc = (struct recv_pdesc *) + dma_alloc_coherent(NULL, sizeof(struct recv_pdesc), + (dma_addr_t *) ðer->rdesc_phys, GFP_KERNEL); + + for (i = 0; i < TX_DESC_SIZE; i++) { + tdesc = &(ether->tdesc->desclist[i]); + + j = ((i + 1) / TX_DESC_SIZE); + + if (j != 0) { + tdesc_phys = &(ether->tdesc_phys->desclist[0]); + ether->start_tx_ptr = (unsigned int)tdesc_phys; + tdesc->next = (unsigned int)ether->start_tx_ptr; + } else { + tdesc_phys = &(ether->tdesc_phys->desclist[i+1]); + tdesc->next = (unsigned int)tdesc_phys; + } + + tdesc->buffer = (unsigned int)ether->tdesc_phys->tran_buf[i]; + tdesc->sl = 0; + tdesc->mode = 0; + } + + for (i = 0; i < RX_DESC_SIZE; i++) { + rdesc = &(ether->rdesc->desclist[i]); + + j = ((i + 1) / RX_DESC_SIZE); + + if (j != 0) { + rdesc_phys = &(ether->rdesc_phys->desclist[0]); + ether->start_rx_ptr = (unsigned int)rdesc_phys; + rdesc->next = (unsigned int)ether->start_rx_ptr; + } else { + rdesc_phys = &(ether->rdesc_phys->desclist[i+1]); + rdesc->next = (unsigned int)rdesc_phys; + } + + rdesc->sl = RX_OWEN_DMA; + rdesc->buffer = (unsigned int)ether->rdesc_phys->recv_buf[i]; + } +} + +static void w90p910_set_fifo_threshold(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int val; + + val = TXTHD | BLENGTH; + __raw_writel(val, ether->reg + REG_FFTCR); +} + +static void w90p910_return_default_idle(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int val; + + val = __raw_readl(ether->reg + REG_MCMDR); + val |= SWR; + __raw_writel(val, ether->reg + REG_MCMDR); +} + +static void w90p910_trigger_rx(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + + __raw_writel(ENSTART, ether->reg + REG_RSDR); +} + +static void w90p910_trigger_tx(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + + __raw_writel(ENSTART, ether->reg + REG_TSDR); +} + +static void w90p910_enable_mac_interrupt(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int val; + + val = ENTXINTR | ENRXINTR | ENRXGD | ENTXCP; + val |= ENTXBERR | ENRXBERR | ENTXABT; + + __raw_writel(val, ether->reg + REG_MIEN); +} + +static void w90p910_get_and_clear_int(struct net_device *dev, + unsigned int *val) +{ + struct w90p910_ether *ether = netdev_priv(dev); + + *val = __raw_readl(ether->reg + REG_MISTA); + __raw_writel(*val, ether->reg + REG_MISTA); +} + +static void w90p910_set_global_maccmd(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int val; + + val = __raw_readl(ether->reg + REG_MCMDR); + val |= MCMDR_SPCRC | MCMDR_ENMDC | MCMDR_ACP | ENMDC; + __raw_writel(val, ether->reg + REG_MCMDR); +} + +static void w90p910_enable_cam(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int val; + + w90p910_write_cam(dev, CAM0, dev->dev_addr); + + val = __raw_readl(ether->reg + REG_CAMEN); + val |= CAM0EN; + __raw_writel(val, ether->reg + REG_CAMEN); +} + +static void w90p910_enable_cam_command(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int val; + + val = CAMCMR_ECMP | CAMCMR_ABP | CAMCMR_AMP; + __raw_writel(val, ether->reg + REG_CAMCMR); +} + +static void w90p910_enable_tx(struct net_device *dev, unsigned int enable) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int val; + + val = __raw_readl(ether->reg + REG_MCMDR); + + if (enable) + val |= MCMDR_TXON; + else + val &= ~MCMDR_TXON; + + __raw_writel(val, ether->reg + REG_MCMDR); +} + +static void w90p910_enable_rx(struct net_device *dev, unsigned int enable) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int val; + + val = __raw_readl(ether->reg + REG_MCMDR); + + if (enable) + val |= MCMDR_RXON; + else + val &= ~MCMDR_RXON; + + __raw_writel(val, ether->reg + REG_MCMDR); +} + +static void w90p910_set_curdest(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + + __raw_writel(ether->start_rx_ptr, ether->reg + REG_RXDLSA); + __raw_writel(ether->start_tx_ptr, ether->reg + REG_TXDLSA); +} + +static void w90p910_reset_mac(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + + spin_lock(ðer->lock); + + w90p910_enable_tx(dev, 0); + w90p910_enable_rx(dev, 0); + w90p910_set_fifo_threshold(dev); + w90p910_return_default_idle(dev); + + if (!netif_queue_stopped(dev)) + netif_stop_queue(dev); + + w90p910_init_desc(dev); + + dev->trans_start = jiffies; + ether->cur_tx = 0x0; + ether->finish_tx = 0x0; + ether->cur_rx = 0x0; + + w90p910_set_curdest(dev); + w90p910_enable_cam(dev); + w90p910_enable_cam_command(dev); + w90p910_enable_mac_interrupt(dev); + w90p910_enable_tx(dev, 1); + w90p910_enable_rx(dev, 1); + w90p910_trigger_tx(dev); + w90p910_trigger_rx(dev); + + dev->trans_start = jiffies; + + if (netif_queue_stopped(dev)) + netif_wake_queue(dev); + + spin_unlock(ðer->lock); +} + +static void w90p910_mdio_write(struct net_device *dev, + int phy_id, int reg, int data) +{ + struct w90p910_ether *ether = netdev_priv(dev); + struct platform_device *pdev; + unsigned int val, i; + + pdev = ether->pdev; + + __raw_writel(data, ether->reg + REG_MIID); + + val = (phy_id << 0x08) | reg; + val |= PHYBUSY | PHYWR | MDCCR_VAL; + __raw_writel(val, ether->reg + REG_MIIDA); + + for (i = 0; i < DELAY; i++) { + if ((__raw_readl(ether->reg + REG_MIIDA) & PHYBUSY) == 0) + break; + } + + if (i == DELAY) + dev_warn(&pdev->dev, "mdio write timed out\n"); +} + +static int w90p910_mdio_read(struct net_device *dev, int phy_id, int reg) +{ + struct w90p910_ether *ether = netdev_priv(dev); + struct platform_device *pdev; + unsigned int val, i, data; + + pdev = ether->pdev; + + val = (phy_id << 0x08) | reg; + val |= PHYBUSY | MDCCR_VAL; + __raw_writel(val, ether->reg + REG_MIIDA); + + for (i = 0; i < DELAY; i++) { + if ((__raw_readl(ether->reg + REG_MIIDA) & PHYBUSY) == 0) + break; + } + + if (i == DELAY) { + dev_warn(&pdev->dev, "mdio read timed out\n"); + data = 0xffff; + } else { + data = __raw_readl(ether->reg + REG_MIID); + } + + return data; +} + +static int set_mac_address(struct net_device *dev, void *addr) +{ + struct sockaddr *address = addr; + + if (!is_valid_ether_addr(address->sa_data)) + return -EADDRNOTAVAIL; + + memcpy(dev->dev_addr, address->sa_data, dev->addr_len); + w90p910_write_cam(dev, CAM0, dev->dev_addr); + + return 0; +} + +static int w90p910_ether_close(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + + dma_free_writecombine(NULL, sizeof(struct w90p910_rxbd), + ether->rdesc, (dma_addr_t)ether->rdesc_phys); + dma_free_writecombine(NULL, sizeof(struct w90p910_txbd), + ether->tdesc, (dma_addr_t)ether->tdesc_phys); + + netif_stop_queue(dev); + + del_timer_sync(ðer->check_timer); + clk_disable(ether->rmiiclk); + clk_disable(ether->clk); + + free_irq(ether->txirq, dev); + free_irq(ether->rxirq, dev); + + return 0; +} + +static struct net_device_stats *w90p910_ether_stats(struct net_device *dev) +{ + struct w90p910_ether *ether; + + ether = netdev_priv(dev); + + return ðer->stats; +} + +static int w90p910_send_frame(struct net_device *dev, + unsigned char *data, int length) +{ + struct w90p910_ether *ether; + struct w90p910_txbd *txbd; + struct platform_device *pdev; + unsigned char *buffer; + + ether = netdev_priv(dev); + pdev = ether->pdev; + + txbd = ðer->tdesc->desclist[ether->cur_tx]; + buffer = ether->tdesc->tran_buf[ether->cur_tx]; + if (length > 1514) { + dev_err(&pdev->dev, "send data %d bytes, check it\n", length); + length = 1514; + } + + txbd->sl = length & 0xFFFF; + + memcpy(buffer, data, length); + + txbd->mode = TX_OWEN_DMA | PADDINGMODE | CRCMODE | MACTXINTEN; + + w90p910_enable_tx(dev, 1); + + w90p910_trigger_tx(dev); + + ether->cur_tx = (ether->cur_tx+1) % TX_DESC_SIZE; + txbd = ðer->tdesc->desclist[ether->cur_tx]; + + dev->trans_start = jiffies; + + if (txbd->mode & TX_OWEN_DMA) + netif_stop_queue(dev); + + return 0; +} + +static int w90p910_ether_start_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + + if (!(w90p910_send_frame(dev, skb->data, skb->len))) { + ether->skb = skb; + dev_kfree_skb_irq(skb); + return 0; + } + return -1; +} + +static irqreturn_t w90p910_tx_interrupt(int irq, void *dev_id) +{ + struct w90p910_ether *ether; + struct w90p910_txbd *txbd; + struct platform_device *pdev; + struct tran_pdesc *tran_pdesc; + struct net_device *dev; + unsigned int cur_entry, entry, status; + + dev = (struct net_device *)dev_id; + ether = netdev_priv(dev); + pdev = ether->pdev; + + spin_lock(ðer->lock); + + w90p910_get_and_clear_int(dev, &status); + + cur_entry = __raw_readl(ether->reg + REG_CTXDSA); + + tran_pdesc = ether->tdesc_phys; + entry = (unsigned int)(&tran_pdesc->desclist[ether->finish_tx]); + + while (entry != cur_entry) { + txbd = ðer->tdesc->desclist[ether->finish_tx]; + + ether->finish_tx = (ether->finish_tx + 1) % TX_DESC_SIZE; + + if (txbd->sl & TXDS_TXCP) { + ether->stats.tx_packets++; + ether->stats.tx_bytes += txbd->sl & 0xFFFF; + } else { + ether->stats.tx_errors++; + } + + txbd->sl = 0x0; + txbd->mode = 0x0; + + if (netif_queue_stopped(dev)) + netif_wake_queue(dev); + + entry = (unsigned int)(&tran_pdesc->desclist[ether->finish_tx]); + } + + if (status & MISTA_EXDEF) { + dev_err(&pdev->dev, "emc defer exceed interrupt\n"); + } else if (status & MISTA_TXBERR) { + dev_err(&pdev->dev, "emc bus error interrupt\n"); + w90p910_reset_mac(dev); + } else if (status & MISTA_TDU) { + if (netif_queue_stopped(dev)) + netif_wake_queue(dev); + } + + spin_unlock(ðer->lock); + + return IRQ_HANDLED; +} + +static void netdev_rx(struct net_device *dev) +{ + struct w90p910_ether *ether; + struct w90p910_rxbd *rxbd; + struct platform_device *pdev; + struct recv_pdesc *rdesc_phys; + struct sk_buff *skb; + unsigned char *data; + unsigned int length, status, val, entry; + + ether = netdev_priv(dev); + pdev = ether->pdev; + rdesc_phys = ether->rdesc_phys; + + rxbd = ðer->rdesc->desclist[ether->cur_rx]; + + do { + val = __raw_readl(ether->reg + REG_CRXDSA); + entry = (unsigned int)&rdesc_phys->desclist[ether->cur_rx]; + + if (val == entry) + break; + + status = rxbd->sl; + length = status & 0xFFFF; + + if (status & RXDS_RXGD) { + data = ether->rdesc->recv_buf[ether->cur_rx]; + skb = dev_alloc_skb(length+2); + if (!skb) { + dev_err(&pdev->dev, "get skb buffer error\n"); + ether->stats.rx_dropped++; + return; + } + + skb->dev = dev; + skb_reserve(skb, 2); + skb_put(skb, length); + skb_copy_to_linear_data(skb, data, length); + skb->protocol = eth_type_trans(skb, dev); + ether->stats.rx_packets++; + ether->stats.rx_bytes += length; + netif_rx(skb); + } else { + ether->stats.rx_errors++; + + if (status & RXDS_RP) { + dev_err(&pdev->dev, "rx runt err\n"); + ether->stats.rx_length_errors++; + } else if (status & RXDS_CRCE) { + dev_err(&pdev->dev, "rx crc err\n"); + ether->stats.rx_crc_errors++; + } + + if (status & RXDS_ALIE) { + dev_err(&pdev->dev, "rx aligment err\n"); + ether->stats.rx_frame_errors++; + } else if (status & RXDS_PTLE) { + dev_err(&pdev->dev, "rx longer err\n"); + ether->stats.rx_over_errors++; + } + } + + rxbd->sl = RX_OWEN_DMA; + rxbd->reserved = 0x0; + ether->cur_rx = (ether->cur_rx+1) % RX_DESC_SIZE; + rxbd = ðer->rdesc->desclist[ether->cur_rx]; + + dev->last_rx = jiffies; + } while (1); +} + +static irqreturn_t w90p910_rx_interrupt(int irq, void *dev_id) +{ + struct net_device *dev; + struct w90p910_ether *ether; + struct platform_device *pdev; + unsigned int status; + + dev = (struct net_device *)dev_id; + ether = netdev_priv(dev); + pdev = ether->pdev; + + spin_lock(ðer->lock); + + w90p910_get_and_clear_int(dev, &status); + + if (status & MISTA_RDU) { + netdev_rx(dev); + + w90p910_trigger_rx(dev); + + spin_unlock(ðer->lock); + return IRQ_HANDLED; + } else if (status & MISTA_RXBERR) { + dev_err(&pdev->dev, "emc rx bus error\n"); + w90p910_reset_mac(dev); + } + + netdev_rx(dev); + spin_unlock(ðer->lock); + return IRQ_HANDLED; +} + +static int w90p910_ether_open(struct net_device *dev) +{ + struct w90p910_ether *ether; + struct platform_device *pdev; + + ether = netdev_priv(dev); + pdev = ether->pdev; + + w90p910_reset_mac(dev); + w90p910_set_fifo_threshold(dev); + w90p910_set_curdest(dev); + w90p910_enable_cam(dev); + w90p910_enable_cam_command(dev); + w90p910_enable_mac_interrupt(dev); + w90p910_set_global_maccmd(dev); + w90p910_enable_rx(dev, 1); + + ether->rx_packets = 0x0; + ether->rx_bytes = 0x0; + + if (request_irq(ether->txirq, w90p910_tx_interrupt, + 0x0, pdev->name, dev)) { + dev_err(&pdev->dev, "register irq tx failed\n"); + return -EAGAIN; + } + + if (request_irq(ether->rxirq, w90p910_rx_interrupt, + 0x0, pdev->name, dev)) { + dev_err(&pdev->dev, "register irq rx failed\n"); + return -EAGAIN; + } + + mod_timer(ðer->check_timer, jiffies + msecs_to_jiffies(1000)); + netif_start_queue(dev); + w90p910_trigger_rx(dev); + + dev_info(&pdev->dev, "%s is OPENED\n", dev->name); + + return 0; +} + +static void w90p910_ether_set_multicast_list(struct net_device *dev) +{ + struct w90p910_ether *ether; + unsigned int rx_mode; + + ether = netdev_priv(dev); + + if (dev->flags & IFF_PROMISC) + rx_mode = CAMCMR_AUP | CAMCMR_AMP | CAMCMR_ABP | CAMCMR_ECMP; + else if ((dev->flags & IFF_ALLMULTI) || dev->mc_list) + rx_mode = CAMCMR_AMP | CAMCMR_ABP | CAMCMR_ECMP; + else + rx_mode = CAMCMR_ECMP | CAMCMR_ABP; + __raw_writel(rx_mode, ether->reg + REG_CAMCMR); +} + +static int w90p910_ether_ioctl(struct net_device *dev, + struct ifreq *ifr, int cmd) +{ + struct w90p910_ether *ether = netdev_priv(dev); + struct mii_ioctl_data *data = if_mii(ifr); + + return generic_mii_ioctl(ðer->mii, data, cmd, NULL); +} + +static void w90p910_get_drvinfo(struct net_device *dev, + struct ethtool_drvinfo *info) +{ + strcpy(info->driver, DRV_MODULE_NAME); + strcpy(info->version, DRV_MODULE_VERSION); +} + +static int w90p910_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct w90p910_ether *ether = netdev_priv(dev); + return mii_ethtool_gset(ðer->mii, cmd); +} + +static int w90p910_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct w90p910_ether *ether = netdev_priv(dev); + return mii_ethtool_sset(ðer->mii, cmd); +} + +static int w90p910_nway_reset(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + return mii_nway_restart(ðer->mii); +} + +static u32 w90p910_get_link(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + return mii_link_ok(ðer->mii); +} + +static const struct ethtool_ops w90p910_ether_ethtool_ops = { + .get_settings = w90p910_get_settings, + .set_settings = w90p910_set_settings, + .get_drvinfo = w90p910_get_drvinfo, + .nway_reset = w90p910_nway_reset, + .get_link = w90p910_get_link, +}; + +static const struct net_device_ops w90p910_ether_netdev_ops = { + .ndo_open = w90p910_ether_open, + .ndo_stop = w90p910_ether_close, + .ndo_start_xmit = w90p910_ether_start_xmit, + .ndo_get_stats = w90p910_ether_stats, + .ndo_set_multicast_list = w90p910_ether_set_multicast_list, + .ndo_set_mac_address = set_mac_address, + .ndo_do_ioctl = w90p910_ether_ioctl, + .ndo_validate_addr = eth_validate_addr, + .ndo_change_mtu = eth_change_mtu, +}; + +static void __init get_mac_address(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + struct platform_device *pdev; + char addr[6]; + + pdev = ether->pdev; + + addr[0] = 0x00; + addr[1] = 0x02; + addr[2] = 0xac; + addr[3] = 0x55; + addr[4] = 0x88; + addr[5] = 0xa8; + + if (is_valid_ether_addr(addr)) + memcpy(dev->dev_addr, &addr, 0x06); + else + dev_err(&pdev->dev, "invalid mac address\n"); +} + +static int w90p910_ether_setup(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + + ether_setup(dev); + dev->netdev_ops = &w90p910_ether_netdev_ops; + dev->ethtool_ops = &w90p910_ether_ethtool_ops; + + dev->tx_queue_len = 16; + dev->dma = 0x0; + dev->watchdog_timeo = TX_TIMEOUT; + + get_mac_address(dev); + + spin_lock_init(ðer->lock); + + ether->cur_tx = 0x0; + ether->cur_rx = 0x0; + ether->finish_tx = 0x0; + ether->linkflag = 0x0; + ether->mii.phy_id = 0x01; + ether->mii.phy_id_mask = 0x1f; + ether->mii.reg_num_mask = 0x1f; + ether->mii.dev = dev; + ether->mii.mdio_read = w90p910_mdio_read; + ether->mii.mdio_write = w90p910_mdio_write; + + setup_timer(ðer->check_timer, w90p910_check_link, + (unsigned long)dev); + + return 0; +} + +static int __devinit w90p910_ether_probe(struct platform_device *pdev) +{ + struct w90p910_ether *ether; + struct net_device *dev; + struct resource *res; + int error; + + dev = alloc_etherdev(sizeof(struct w90p910_ether)); + if (!dev) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (res == NULL) { + dev_err(&pdev->dev, "failed to get I/O memory\n"); + error = -ENXIO; + goto failed_free; + } + + res = request_mem_region(res->start, resource_size(res), pdev->name); + if (res == NULL) { + dev_err(&pdev->dev, "failed to request I/O memory\n"); + error = -EBUSY; + goto failed_free; + } + + ether = netdev_priv(dev); + + ether->reg = ioremap(res->start, resource_size(res)); + if (ether->reg == NULL) { + dev_err(&pdev->dev, "failed to remap I/O memory\n"); + error = -ENXIO; + goto failed_free_mem; + } + + ether->txirq = platform_get_irq(pdev, 0); + if (ether->txirq < 0) { + dev_err(&pdev->dev, "failed to get ether tx irq\n"); + error = -ENXIO; + goto failed_free_io; + } + + ether->rxirq = platform_get_irq(pdev, 1); + if (ether->rxirq < 0) { + dev_err(&pdev->dev, "failed to get ether rx irq\n"); + error = -ENXIO; + goto failed_free_txirq; + } + + platform_set_drvdata(pdev, dev); + + ether->clk = clk_get(&pdev->dev, NULL); + if (IS_ERR(ether->clk)) { + dev_err(&pdev->dev, "failed to get ether clock\n"); + error = PTR_ERR(ether->clk); + goto failed_free_rxirq; + } + + ether->rmiiclk = clk_get(&pdev->dev, "RMII"); + if (IS_ERR(ether->rmiiclk)) { + dev_err(&pdev->dev, "failed to get ether clock\n"); + error = PTR_ERR(ether->rmiiclk); + goto failed_put_clk; + } + + ether->pdev = pdev; + + w90p910_ether_setup(dev); + + error = register_netdev(dev); + if (error != 0) { + dev_err(&pdev->dev, "Regiter EMC w90p910 FAILED\n"); + error = -ENODEV; + goto failed_put_rmiiclk; + } + + return 0; +failed_put_rmiiclk: + clk_put(ether->rmiiclk); +failed_put_clk: + clk_put(ether->clk); +failed_free_rxirq: + free_irq(ether->rxirq, pdev); + platform_set_drvdata(pdev, NULL); +failed_free_txirq: + free_irq(ether->txirq, pdev); +failed_free_io: + iounmap(ether->reg); +failed_free_mem: + release_mem_region(res->start, resource_size(res)); +failed_free: + free_netdev(dev); + return error; +} + +static int __devexit w90p910_ether_remove(struct platform_device *pdev) +{ + struct net_device *dev = platform_get_drvdata(pdev); + struct w90p910_ether *ether = netdev_priv(dev); + + unregister_netdev(dev); + clk_put(ether->rmiiclk); + clk_put(ether->clk); + del_timer_sync(ðer->check_timer); + platform_set_drvdata(pdev, NULL); + free_netdev(dev); + return 0; +} + +static struct platform_driver w90p910_ether_driver = { + .probe = w90p910_ether_probe, + .remove = __devexit_p(w90p910_ether_remove), + .driver = { + .name = "w90p910-emc", + .owner = THIS_MODULE, + }, +}; + +static int __init w90p910_ether_init(void) +{ + return platform_driver_register(&w90p910_ether_driver); +} + +static void __exit w90p910_ether_exit(void) +{ + platform_driver_unregister(&w90p910_ether_driver); +} + +module_init(w90p910_ether_init); +module_exit(w90p910_ether_exit); + +MODULE_AUTHOR("Wan ZongShun "); +MODULE_DESCRIPTION("w90p910 MAC driver!"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:w90p910-emc"); + -- GitLab From e3afe7b75ed8f809c1473ea9b39267487c187ccb Mon Sep 17 00:00:00 2001 From: John Dykstra Date: Thu, 16 Jul 2009 05:04:51 +0000 Subject: [PATCH 0111/1342] tcp: Fix MD5 signature checking on IPv4 mapped sockets Fix MD5 signature checking so that an IPv4 active open to an IPv6 socket can succeed. In particular, use the correct address family's signature generation function for the SYN/ACK. Reported-by: Stephen Hemminger Signed-off-by: John Dykstra Signed-off-by: David S. Miller --- include/net/tcp.h | 5 +++++ net/ipv4/tcp_ipv4.c | 1 + net/ipv4/tcp_output.c | 2 +- net/ipv6/tcp_ipv6.c | 1 + 4 files changed, 8 insertions(+), 1 deletion(-) diff --git a/include/net/tcp.h b/include/net/tcp.h index 19f4150f4d4..88af8430647 100644 --- a/include/net/tcp.h +++ b/include/net/tcp.h @@ -1425,6 +1425,11 @@ struct tcp_request_sock_ops { #ifdef CONFIG_TCP_MD5SIG struct tcp_md5sig_key *(*md5_lookup) (struct sock *sk, struct request_sock *req); + int (*calc_md5_hash) (char *location, + struct tcp_md5sig_key *md5, + struct sock *sk, + struct request_sock *req, + struct sk_buff *skb); #endif }; diff --git a/net/ipv4/tcp_ipv4.c b/net/ipv4/tcp_ipv4.c index 5a1ca2698c8..7c107eb876c 100644 --- a/net/ipv4/tcp_ipv4.c +++ b/net/ipv4/tcp_ipv4.c @@ -1160,6 +1160,7 @@ struct request_sock_ops tcp_request_sock_ops __read_mostly = { #ifdef CONFIG_TCP_MD5SIG static struct tcp_request_sock_ops tcp_request_sock_ipv4_ops = { .md5_lookup = tcp_v4_reqsk_md5_lookup, + .calc_md5_hash = tcp_v4_md5_hash_skb, }; #endif diff --git a/net/ipv4/tcp_output.c b/net/ipv4/tcp_output.c index 5bdf08d312d..bd62712848f 100644 --- a/net/ipv4/tcp_output.c +++ b/net/ipv4/tcp_output.c @@ -2261,7 +2261,7 @@ struct sk_buff *tcp_make_synack(struct sock *sk, struct dst_entry *dst, #ifdef CONFIG_TCP_MD5SIG /* Okay, we have all we need - do the md5 hash if needed */ if (md5) { - tp->af_specific->calc_md5_hash(md5_hash_location, + tcp_rsk(req)->af_specific->calc_md5_hash(md5_hash_location, md5, NULL, req, skb); } #endif diff --git a/net/ipv6/tcp_ipv6.c b/net/ipv6/tcp_ipv6.c index 58810c65b63..ae3d6575356 100644 --- a/net/ipv6/tcp_ipv6.c +++ b/net/ipv6/tcp_ipv6.c @@ -896,6 +896,7 @@ struct request_sock_ops tcp6_request_sock_ops __read_mostly = { #ifdef CONFIG_TCP_MD5SIG static struct tcp_request_sock_ops tcp_request_sock_ipv6_ops = { .md5_lookup = tcp_v6_reqsk_md5_lookup, + .calc_md5_hash = tcp_v6_md5_hash_skb, }; #endif -- GitLab From e547bc1eccf539b7403138d8ded913ffd2b7fd0d Mon Sep 17 00:00:00 2001 From: John Dykstra Date: Fri, 17 Jul 2009 09:23:22 +0000 Subject: [PATCH 0112/1342] tcp: Use correct peer adr when copying MD5 keys When the TCP connection handshake completes on the passive side, a variety of state must be set up in the "child" sock, including the key if MD5 authentication is being used. Fix TCP for both address families to label the key with the peer's destination address, rather than the address from the listening sock, which is usually the wildcard. Reported-by: Stephen Hemminger Signed-off-by: John Dykstra Signed-off-by: David S. Miller --- net/ipv4/tcp_ipv4.c | 2 +- net/ipv6/tcp_ipv6.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/net/ipv4/tcp_ipv4.c b/net/ipv4/tcp_ipv4.c index 7c107eb876c..6d88219c5e2 100644 --- a/net/ipv4/tcp_ipv4.c +++ b/net/ipv4/tcp_ipv4.c @@ -1374,7 +1374,7 @@ struct sock *tcp_v4_syn_recv_sock(struct sock *sk, struct sk_buff *skb, */ char *newkey = kmemdup(key->key, key->keylen, GFP_ATOMIC); if (newkey != NULL) - tcp_v4_md5_do_add(newsk, inet_sk(sk)->daddr, + tcp_v4_md5_do_add(newsk, newinet->daddr, newkey, key->keylen); newsk->sk_route_caps &= ~NETIF_F_GSO_MASK; } diff --git a/net/ipv6/tcp_ipv6.c b/net/ipv6/tcp_ipv6.c index ae3d6575356..d849dd53b78 100644 --- a/net/ipv6/tcp_ipv6.c +++ b/net/ipv6/tcp_ipv6.c @@ -1442,7 +1442,7 @@ static struct sock * tcp_v6_syn_recv_sock(struct sock *sk, struct sk_buff *skb, */ char *newkey = kmemdup(key->key, key->keylen, GFP_ATOMIC); if (newkey != NULL) - tcp_v6_md5_do_add(newsk, &inet6_sk(sk)->daddr, + tcp_v6_md5_do_add(newsk, &newnp->daddr, newkey, key->keylen); } #endif -- GitLab From 55fe27f7e2c9d24ce870136bd99ae67b020122d1 Mon Sep 17 00:00:00 2001 From: Frank Roth Date: Mon, 20 Jul 2009 17:00:14 +0200 Subject: [PATCH 0113/1342] ALSA: ctxfi: Swapped SURROUND-SIDE channels on emu20k2 On Soundblaster X-FI Titanium with emu20k2 the SIDE and SURROUND channels were swapped and wrong. I double checked it with connector colors and creative soundblaster windows drivers. So I swapped them to the true order. Now "speaker-test -c6" and "speaker-test -c8" are working fine. Signed-off-by: Frank Roth Signed-off-by: Takashi Iwai --- sound/pci/ctxfi/ctdaio.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/sound/pci/ctxfi/ctdaio.c b/sound/pci/ctxfi/ctdaio.c index 082e35c08c0..deb6cfa7360 100644 --- a/sound/pci/ctxfi/ctdaio.c +++ b/sound/pci/ctxfi/ctdaio.c @@ -57,9 +57,9 @@ struct daio_rsc_idx idx_20k1[NUM_DAIOTYP] = { struct daio_rsc_idx idx_20k2[NUM_DAIOTYP] = { [LINEO1] = {.left = 0x40, .right = 0x41}, - [LINEO2] = {.left = 0x70, .right = 0x71}, + [LINEO2] = {.left = 0x60, .right = 0x61}, [LINEO3] = {.left = 0x50, .right = 0x51}, - [LINEO4] = {.left = 0x60, .right = 0x61}, + [LINEO4] = {.left = 0x70, .right = 0x71}, [LINEIM] = {.left = 0x45, .right = 0xc5}, [SPDIFOO] = {.left = 0x00, .right = 0x01}, [SPDIFIO] = {.left = 0x05, .right = 0x85}, -- GitLab From 3ba81f3ece3cfa4ffb06d21ac93b8cad7fbe6a73 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Thu, 16 Jul 2009 05:24:08 +0000 Subject: [PATCH 0114/1342] net: Micrel KS8851 SPI network driver Network driver for the SPI version of the Micrel KS8851 network chip. Signed-off-by: Ben Dooks Signed-off-by: David S. Miller --- drivers/net/Kconfig | 6 + drivers/net/Makefile | 1 + drivers/net/ks8851.c | 1322 ++++++++++++++++++++++++++++++++++++++++++ drivers/net/ks8851.h | 296 ++++++++++ 4 files changed, 1625 insertions(+) create mode 100644 drivers/net/ks8851.c create mode 100644 drivers/net/ks8851.h diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index c155bd3ec9f..b5a7513df4e 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -1729,6 +1729,12 @@ config KS8842 help This platform driver is for Micrel KSZ8842 chip. +config KS8851 + tristate "Micrel KS8851 SPI" + depends on SPI + help + SPI driver for Micrel KS8851 SPI attached network chip. + config VIA_RHINE tristate "VIA Rhine support" depends on NET_PCI && PCI diff --git a/drivers/net/Makefile b/drivers/net/Makefile index 4b58a59f211..ead8cab3cfe 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -88,6 +88,7 @@ obj-$(CONFIG_SKGE) += skge.o obj-$(CONFIG_SKY2) += sky2.o obj-$(CONFIG_SKFP) += skfp/ obj-$(CONFIG_KS8842) += ks8842.o +obj-$(CONFIG_KS8851) += ks8851.o obj-$(CONFIG_VIA_RHINE) += via-rhine.o obj-$(CONFIG_VIA_VELOCITY) += via-velocity.o obj-$(CONFIG_ADAPTEC_STARFIRE) += starfire.o diff --git a/drivers/net/ks8851.c b/drivers/net/ks8851.c new file mode 100644 index 00000000000..9a1dea60c1c --- /dev/null +++ b/drivers/net/ks8851.c @@ -0,0 +1,1322 @@ +/* drivers/net/ks8651.c + * + * Copyright 2009 Simtec Electronics + * http://www.simtec.co.uk/ + * Ben Dooks + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#define DEBUG + +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +#include "ks8851.h" + +/** + * struct ks8851_rxctrl - KS8851 driver rx control + * @mchash: Multicast hash-table data. + * @rxcr1: KS_RXCR1 register setting + * @rxcr2: KS_RXCR2 register setting + * + * Representation of the settings needs to control the receive filtering + * such as the multicast hash-filter and the receive register settings. This + * is used to make the job of working out if the receive settings change and + * then issuing the new settings to the worker that will send the necessary + * commands. + */ +struct ks8851_rxctrl { + u16 mchash[4]; + u16 rxcr1; + u16 rxcr2; +}; + +/** + * union ks8851_tx_hdr - tx header data + * @txb: The header as bytes + * @txw: The header as 16bit, little-endian words + * + * A dual representation of the tx header data to allow + * access to individual bytes, and to allow 16bit accesses + * with 16bit alignment. + */ +union ks8851_tx_hdr { + u8 txb[6]; + __le16 txw[3]; +}; + +/** + * struct ks8851_net - KS8851 driver private data + * @netdev: The network device we're bound to + * @spidev: The spi device we're bound to. + * @lock: Lock to ensure that the device is not accessed when busy. + * @statelock: Lock on this structure for tx list. + * @mii: The MII state information for the mii calls. + * @rxctrl: RX settings for @rxctrl_work. + * @tx_work: Work queue for tx packets + * @irq_work: Work queue for servicing interrupts + * @rxctrl_work: Work queue for updating RX mode and multicast lists + * @txq: Queue of packets for transmission. + * @spi_msg1: pre-setup SPI transfer with one message, @spi_xfer1. + * @spi_msg2: pre-setup SPI transfer with two messages, @spi_xfer2. + * @txh: Space for generating packet TX header in DMA-able data + * @rxd: Space for receiving SPI data, in DMA-able space. + * @txd: Space for transmitting SPI data, in DMA-able space. + * @msg_enable: The message flags controlling driver output (see ethtool). + * @fid: Incrementing frame id tag. + * @rc_ier: Cached copy of KS_IER. + * @rc_rxqcr: Cached copy of KS_RXQCR. + * + * The @lock ensures that the chip is protected when certain operations are + * in progress. When the read or write packet transfer is in progress, most + * of the chip registers are not ccessible until the transfer is finished and + * the DMA has been de-asserted. + * + * The @statelock is used to protect information in the structure which may + * need to be accessed via several sources, such as the network driver layer + * or one of the work queues. + * + * We align the buffers we may use for rx/tx to ensure that if the SPI driver + * wants to DMA map them, it will not have any problems with data the driver + * modifies. + */ +struct ks8851_net { + struct net_device *netdev; + struct spi_device *spidev; + struct mutex lock; + spinlock_t statelock; + + union ks8851_tx_hdr txh ____cacheline_aligned; + u8 rxd[8]; + u8 txd[8]; + + u32 msg_enable ____cacheline_aligned; + u16 tx_space; + u8 fid; + + u16 rc_ier; + u16 rc_rxqcr; + + struct mii_if_info mii; + struct ks8851_rxctrl rxctrl; + + struct work_struct tx_work; + struct work_struct irq_work; + struct work_struct rxctrl_work; + + struct sk_buff_head txq; + + struct spi_message spi_msg1; + struct spi_message spi_msg2; + struct spi_transfer spi_xfer1; + struct spi_transfer spi_xfer2[2]; +}; + +static int msg_enable; + +#define ks_info(_ks, _msg...) dev_info(&(_ks)->spidev->dev, _msg) +#define ks_warn(_ks, _msg...) dev_warn(&(_ks)->spidev->dev, _msg) +#define ks_dbg(_ks, _msg...) dev_dbg(&(_ks)->spidev->dev, _msg) +#define ks_err(_ks, _msg...) dev_err(&(_ks)->spidev->dev, _msg) + +/* shift for byte-enable data */ +#define BYTE_EN(_x) ((_x) << 2) + +/* turn register number and byte-enable mask into data for start of packet */ +#define MK_OP(_byteen, _reg) (BYTE_EN(_byteen) | (_reg) << (8+2) | (_reg) >> 6) + +/* SPI register read/write calls. + * + * All these calls issue SPI transactions to access the chip's registers. They + * all require that the necessary lock is held to prevent accesses when the + * chip is busy transfering packet data (RX/TX FIFO accesses). + */ + +/** + * ks8851_wrreg16 - write 16bit register value to chip + * @ks: The chip state + * @reg: The register address + * @val: The value to write + * + * Issue a write to put the value @val into the register specified in @reg. + */ +static void ks8851_wrreg16(struct ks8851_net *ks, unsigned reg, unsigned val) +{ + struct spi_transfer *xfer = &ks->spi_xfer1; + struct spi_message *msg = &ks->spi_msg1; + __le16 txb[2]; + int ret; + + txb[0] = cpu_to_le16(MK_OP(reg & 2 ? 0xC : 0x03, reg) | KS_SPIOP_WR); + txb[1] = cpu_to_le16(val); + + xfer->tx_buf = txb; + xfer->rx_buf = NULL; + xfer->len = 4; + + ret = spi_sync(ks->spidev, msg); + if (ret < 0) + ks_err(ks, "spi_sync() failed\n"); +} + +/** + * ks8851_rx_1msg - select whether to use one or two messages for spi read + * @ks: The device structure + * + * Return whether to generate a single message with a tx and rx buffer + * supplied to spi_sync(), or alternatively send the tx and rx buffers + * as separate messages. + * + * Depending on the hardware in use, a single message may be more efficient + * on interrupts or work done by the driver. + * + * This currently always returns true until we add some per-device data passed + * from the platform code to specify which mode is better. + */ +static inline bool ks8851_rx_1msg(struct ks8851_net *ks) +{ + return true; +} + +/** + * ks8851_rdreg - issue read register command and return the data + * @ks: The device state + * @op: The register address and byte enables in message format. + * @rxb: The RX buffer to return the result into + * @rxl: The length of data expected. + * + * This is the low level read call that issues the necessary spi message(s) + * to read data from the register specified in @op. + */ +static void ks8851_rdreg(struct ks8851_net *ks, unsigned op, + u8 *rxb, unsigned rxl) +{ + struct spi_transfer *xfer; + struct spi_message *msg; + __le16 *txb = (__le16 *)ks->txd; + u8 *trx = ks->rxd; + int ret; + + txb[0] = cpu_to_le16(op | KS_SPIOP_RD); + + if (ks8851_rx_1msg(ks)) { + msg = &ks->spi_msg1; + xfer = &ks->spi_xfer1; + + xfer->tx_buf = txb; + xfer->rx_buf = trx; + xfer->len = rxl + 2; + } else { + msg = &ks->spi_msg2; + xfer = ks->spi_xfer2; + + xfer->tx_buf = txb; + xfer->rx_buf = NULL; + xfer->len = 2; + + xfer++; + xfer->tx_buf = NULL; + xfer->rx_buf = trx; + xfer->len = rxl; + } + + ret = spi_sync(ks->spidev, msg); + if (ret < 0) + ks_err(ks, "read: spi_sync() failed\n"); + else if (ks8851_rx_1msg(ks)) + memcpy(rxb, trx + 2, rxl); + else + memcpy(rxb, trx, rxl); +} + +/** + * ks8851_rdreg8 - read 8 bit register from device + * @ks: The chip information + * @reg: The register address + * + * Read a 8bit register from the chip, returning the result +*/ +static unsigned ks8851_rdreg8(struct ks8851_net *ks, unsigned reg) +{ + u8 rxb[1]; + + ks8851_rdreg(ks, MK_OP(1 << (reg & 3), reg), rxb, 1); + return rxb[0]; +} + +/** + * ks8851_rdreg16 - read 16 bit register from device + * @ks: The chip information + * @reg: The register address + * + * Read a 16bit register from the chip, returning the result +*/ +static unsigned ks8851_rdreg16(struct ks8851_net *ks, unsigned reg) +{ + __le16 rx = 0; + + ks8851_rdreg(ks, MK_OP(reg & 2 ? 0xC : 0x3, reg), (u8 *)&rx, 2); + return le16_to_cpu(rx); +} + +/** + * ks8851_rdreg32 - read 32 bit register from device + * @ks: The chip information + * @reg: The register address + * + * Read a 32bit register from the chip. + * + * Note, this read requires the address be aligned to 4 bytes. +*/ +static unsigned ks8851_rdreg32(struct ks8851_net *ks, unsigned reg) +{ + __le32 rx = 0; + + WARN_ON(reg & 3); + + ks8851_rdreg(ks, MK_OP(0xf, reg), (u8 *)&rx, 4); + return le32_to_cpu(rx); +} + +/** + * ks8851_soft_reset - issue one of the soft reset to the device + * @ks: The device state. + * @op: The bit(s) to set in the GRR + * + * Issue the relevant soft-reset command to the device's GRR register + * specified by @op. + * + * Note, the delays are in there as a caution to ensure that the reset + * has time to take effect and then complete. Since the datasheet does + * not currently specify the exact sequence, we have chosen something + * that seems to work with our device. + */ +static void ks8851_soft_reset(struct ks8851_net *ks, unsigned op) +{ + ks8851_wrreg16(ks, KS_GRR, op); + mdelay(1); /* wait a short time to effect reset */ + ks8851_wrreg16(ks, KS_GRR, 0); + mdelay(1); /* wait for condition to clear */ +} + +/** + * ks8851_write_mac_addr - write mac address to device registers + * @dev: The network device + * + * Update the KS8851 MAC address registers from the address in @dev. + * + * This call assumes that the chip is not running, so there is no need to + * shutdown the RXQ process whilst setting this. +*/ +static int ks8851_write_mac_addr(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + u16 *mcp = (u16 *)dev->dev_addr; + + mutex_lock(&ks->lock); + + ks8851_wrreg16(ks, KS_MARL, mcp[0]); + ks8851_wrreg16(ks, KS_MARM, mcp[1]); + ks8851_wrreg16(ks, KS_MARH, mcp[2]); + + mutex_unlock(&ks->lock); + + return 0; +} + +/** + * ks8851_init_mac - initialise the mac address + * @ks: The device structure + * + * Get or create the initial mac address for the device and then set that + * into the station address register. Currently we assume that the device + * does not have a valid mac address in it, and so we use random_ether_addr() + * to create a new one. + * + * In future, the driver should check to see if the device has an EEPROM + * attached and whether that has a valid ethernet address in it. + */ +static void ks8851_init_mac(struct ks8851_net *ks) +{ + struct net_device *dev = ks->netdev; + + random_ether_addr(dev->dev_addr); + ks8851_write_mac_addr(dev); +} + +/** + * ks8851_irq - device interrupt handler + * @irq: Interrupt number passed from the IRQ hnalder. + * @pw: The private word passed to register_irq(), our struct ks8851_net. + * + * Disable the interrupt from happening again until we've processed the + * current status by scheduling ks8851_irq_work(). + */ +static irqreturn_t ks8851_irq(int irq, void *pw) +{ + struct ks8851_net *ks = pw; + + disable_irq_nosync(irq); + schedule_work(&ks->irq_work); + return IRQ_HANDLED; +} + +/** + * ks8851_rdfifo - read data from the receive fifo + * @ks: The device state. + * @buff: The buffer address + * @len: The length of the data to read + * + * Issue an RXQ FIFO read command and read the @len ammount of data from + * the FIFO into the buffer specified by @buff. + */ +static void ks8851_rdfifo(struct ks8851_net *ks, u8 *buff, unsigned len) +{ + struct spi_transfer *xfer = ks->spi_xfer2; + struct spi_message *msg = &ks->spi_msg2; + u8 txb[1]; + int ret; + + if (netif_msg_rx_status(ks)) + ks_dbg(ks, "%s: %d@%p\n", __func__, len, buff); + + /* set the operation we're issuing */ + txb[0] = KS_SPIOP_RXFIFO; + + xfer->tx_buf = txb; + xfer->rx_buf = NULL; + xfer->len = 1; + + xfer++; + xfer->rx_buf = buff; + xfer->tx_buf = NULL; + xfer->len = len; + + ret = spi_sync(ks->spidev, msg); + if (ret < 0) + ks_err(ks, "%s: spi_sync() failed\n", __func__); +} + +/** + * ks8851_dbg_dumpkkt - dump initial packet contents to debug + * @ks: The device state + * @rxpkt: The data for the received packet + * + * Dump the initial data from the packet to dev_dbg(). +*/ +static void ks8851_dbg_dumpkkt(struct ks8851_net *ks, u8 *rxpkt) +{ + ks_dbg(ks, "pkt %02x%02x%02x%02x %02x%02x%02x%02x %02x%02x%02x%02x\n", + rxpkt[4], rxpkt[5], rxpkt[6], rxpkt[7], + rxpkt[8], rxpkt[9], rxpkt[10], rxpkt[11], + rxpkt[12], rxpkt[13], rxpkt[14], rxpkt[15]); +} + +/** + * ks8851_rx_pkts - receive packets from the host + * @ks: The device information. + * + * This is called from the IRQ work queue when the system detects that there + * are packets in the receive queue. Find out how many packets there are and + * read them from the FIFO. + */ +static void ks8851_rx_pkts(struct ks8851_net *ks) +{ + struct sk_buff *skb; + unsigned rxfc; + unsigned rxlen; + unsigned rxstat; + u32 rxh; + u8 *rxpkt; + + rxfc = ks8851_rdreg8(ks, KS_RXFC); + + if (netif_msg_rx_status(ks)) + ks_dbg(ks, "%s: %d packets\n", __func__, rxfc); + + /* Currently we're issuing a read per packet, but we could possibly + * improve the code by issuing a single read, getting the receive + * header, allocating the packet and then reading the packet data + * out in one go. + * + * This form of operation would require us to hold the SPI bus' + * chipselect low during the entie transaction to avoid any + * reset to the data stream comming from the chip. + */ + + for (; rxfc != 0; rxfc--) { + rxh = ks8851_rdreg32(ks, KS_RXFHSR); + rxstat = rxh & 0xffff; + rxlen = rxh >> 16; + + if (netif_msg_rx_status(ks)) + ks_dbg(ks, "rx: stat 0x%04x, len 0x%04x\n", + rxstat, rxlen); + + /* the length of the packet includes the 32bit CRC */ + + /* set dma read address */ + ks8851_wrreg16(ks, KS_RXFDPR, RXFDPR_RXFPAI | 0x00); + + /* start the packet dma process, and set auto-dequeue rx */ + ks8851_wrreg16(ks, KS_RXQCR, + ks->rc_rxqcr | RXQCR_SDA | RXQCR_ADRFE); + + if (rxlen > 0) { + skb = netdev_alloc_skb(ks->netdev, rxlen + 2 + 8); + if (!skb) { + /* todo - dump frame and move on */ + } + + /* two bytes to ensure ip is aligned, and four bytes + * for the status header and 4 bytes of garbage */ + skb_reserve(skb, 2 + 4 + 4); + + rxpkt = skb_put(skb, rxlen - 4) - 8; + + /* align the packet length to 4 bytes, and add 4 bytes + * as we're getting the rx status header as well */ + ks8851_rdfifo(ks, rxpkt, ALIGN(rxlen, 4) + 8); + + if (netif_msg_pktdata(ks)) + ks8851_dbg_dumpkkt(ks, rxpkt); + + skb->protocol = eth_type_trans(skb, ks->netdev); + netif_rx(skb); + + ks->netdev->stats.rx_packets++; + ks->netdev->stats.rx_bytes += rxlen - 4; + } + + ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr); + } +} + +/** + * ks8851_irq_work - work queue handler for dealing with interrupt requests + * @work: The work structure that was scheduled by schedule_work() + * + * This is the handler invoked when the ks8851_irq() is called to find out + * what happened, as we cannot allow ourselves to sleep whilst waiting for + * anything other process has the chip's lock. + * + * Read the interrupt status, work out what needs to be done and then clear + * any of the interrupts that are not needed. + */ +static void ks8851_irq_work(struct work_struct *work) +{ + struct ks8851_net *ks = container_of(work, struct ks8851_net, irq_work); + unsigned status; + unsigned handled = 0; + + mutex_lock(&ks->lock); + + status = ks8851_rdreg16(ks, KS_ISR); + + if (netif_msg_intr(ks)) + dev_dbg(&ks->spidev->dev, "%s: status 0x%04x\n", + __func__, status); + + if (status & IRQ_LCI) { + /* should do something about checking link status */ + handled |= IRQ_LCI; + } + + if (status & IRQ_LDI) { + u16 pmecr = ks8851_rdreg16(ks, KS_PMECR); + pmecr &= ~PMECR_WKEVT_MASK; + ks8851_wrreg16(ks, KS_PMECR, pmecr | PMECR_WKEVT_LINK); + + handled |= IRQ_LDI; + } + + if (status & IRQ_RXPSI) + handled |= IRQ_RXPSI; + + if (status & IRQ_TXI) { + handled |= IRQ_TXI; + + /* no lock here, tx queue should have been stopped */ + + /* update our idea of how much tx space is available to the + * system */ + ks->tx_space = ks8851_rdreg16(ks, KS_TXMIR); + + if (netif_msg_intr(ks)) + ks_dbg(ks, "%s: txspace %d\n", __func__, ks->tx_space); + } + + if (status & IRQ_RXI) + handled |= IRQ_RXI; + + if (status & IRQ_SPIBEI) { + dev_err(&ks->spidev->dev, "%s: spi bus error\n", __func__); + handled |= IRQ_SPIBEI; + } + + ks8851_wrreg16(ks, KS_ISR, handled); + + if (status & IRQ_RXI) { + /* the datasheet says to disable the rx interrupt during + * packet read-out, however we're masking the interrupt + * from the device so do not bother masking just the RX + * from the device. */ + + ks8851_rx_pkts(ks); + } + + /* if something stopped the rx process, probably due to wanting + * to change the rx settings, then do something about restarting + * it. */ + if (status & IRQ_RXPSI) { + struct ks8851_rxctrl *rxc = &ks->rxctrl; + + /* update the multicast hash table */ + ks8851_wrreg16(ks, KS_MAHTR0, rxc->mchash[0]); + ks8851_wrreg16(ks, KS_MAHTR1, rxc->mchash[1]); + ks8851_wrreg16(ks, KS_MAHTR2, rxc->mchash[2]); + ks8851_wrreg16(ks, KS_MAHTR3, rxc->mchash[3]); + + ks8851_wrreg16(ks, KS_RXCR2, rxc->rxcr2); + ks8851_wrreg16(ks, KS_RXCR1, rxc->rxcr1); + } + + mutex_unlock(&ks->lock); + + if (status & IRQ_TXI) + netif_wake_queue(ks->netdev); + + enable_irq(ks->netdev->irq); +} + +/** + * calc_txlen - calculate size of message to send packet + * @len: Lenght of data + * + * Returns the size of the TXFIFO message needed to send + * this packet. + */ +static inline unsigned calc_txlen(unsigned len) +{ + return ALIGN(len + 4, 4); +} + +/** + * ks8851_wrpkt - write packet to TX FIFO + * @ks: The device state. + * @txp: The sk_buff to transmit. + * @irq: IRQ on completion of the packet. + * + * Send the @txp to the chip. This means creating the relevant packet header + * specifying the length of the packet and the other information the chip + * needs, such as IRQ on completion. Send the header and the packet data to + * the device. + */ +static void ks8851_wrpkt(struct ks8851_net *ks, struct sk_buff *txp, bool irq) +{ + struct spi_transfer *xfer = ks->spi_xfer2; + struct spi_message *msg = &ks->spi_msg2; + unsigned fid = 0; + int ret; + + if (netif_msg_tx_queued(ks)) + dev_dbg(&ks->spidev->dev, "%s: skb %p, %d@%p, irq %d\n", + __func__, txp, txp->len, txp->data, irq); + + fid = ks->fid++; + fid &= TXFR_TXFID_MASK; + + if (irq) + fid |= TXFR_TXIC; /* irq on completion */ + + /* start header at txb[1] to align txw entries */ + ks->txh.txb[1] = KS_SPIOP_TXFIFO; + ks->txh.txw[1] = cpu_to_le16(fid); + ks->txh.txw[2] = cpu_to_le16(txp->len); + + xfer->tx_buf = &ks->txh.txb[1]; + xfer->rx_buf = NULL; + xfer->len = 5; + + xfer++; + xfer->tx_buf = txp->data; + xfer->rx_buf = NULL; + xfer->len = ALIGN(txp->len, 4); + + ret = spi_sync(ks->spidev, msg); + if (ret < 0) + ks_err(ks, "%s: spi_sync() failed\n", __func__); +} + +/** + * ks8851_done_tx - update and then free skbuff after transmitting + * @ks: The device state + * @txb: The buffer transmitted + */ +static void ks8851_done_tx(struct ks8851_net *ks, struct sk_buff *txb) +{ + struct net_device *dev = ks->netdev; + + dev->stats.tx_bytes += txb->len; + dev->stats.tx_packets++; + + dev_kfree_skb(txb); +} + +/** + * ks8851_tx_work - process tx packet(s) + * @work: The work strucutre what was scheduled. + * + * This is called when a number of packets have been scheduled for + * transmission and need to be sent to the device. + */ +static void ks8851_tx_work(struct work_struct *work) +{ + struct ks8851_net *ks = container_of(work, struct ks8851_net, tx_work); + struct sk_buff *txb; + bool last = false; + + mutex_lock(&ks->lock); + + while (!last) { + txb = skb_dequeue(&ks->txq); + last = skb_queue_empty(&ks->txq); + + ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr | RXQCR_SDA); + ks8851_wrpkt(ks, txb, last); + ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr); + ks8851_wrreg16(ks, KS_TXQCR, TXQCR_METFE); + + ks8851_done_tx(ks, txb); + } + + mutex_unlock(&ks->lock); +} + +/** + * ks8851_set_powermode - set power mode of the device + * @ks: The device state + * @pwrmode: The power mode value to write to KS_PMECR. + * + * Change the power mode of the chip. + */ +static void ks8851_set_powermode(struct ks8851_net *ks, unsigned pwrmode) +{ + unsigned pmecr; + + if (netif_msg_hw(ks)) + ks_dbg(ks, "setting power mode %d\n", pwrmode); + + pmecr = ks8851_rdreg16(ks, KS_PMECR); + pmecr &= ~PMECR_PM_MASK; + pmecr |= pwrmode; + + ks8851_wrreg16(ks, KS_PMECR, pmecr); +} + +/** + * ks8851_net_open - open network device + * @dev: The network device being opened. + * + * Called when the network device is marked active, such as a user executing + * 'ifconfig up' on the device. + */ +static int ks8851_net_open(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + + /* lock the card, even if we may not actually be doing anything + * else at the moment */ + mutex_lock(&ks->lock); + + if (netif_msg_ifup(ks)) + ks_dbg(ks, "opening %s\n", dev->name); + + /* bring chip out of any power saving mode it was in */ + ks8851_set_powermode(ks, PMECR_PM_NORMAL); + + /* issue a soft reset to the RX/TX QMU to put it into a known + * state. */ + ks8851_soft_reset(ks, GRR_QMU); + + /* setup transmission parameters */ + + ks8851_wrreg16(ks, KS_TXCR, (TXCR_TXE | /* enable transmit process */ + TXCR_TXPE | /* pad to min length */ + TXCR_TXCRC | /* add CRC */ + TXCR_TXFCE)); /* enable flow control */ + + /* auto-increment tx data, reset tx pointer */ + ks8851_wrreg16(ks, KS_TXFDPR, TXFDPR_TXFPAI); + + /* setup receiver control */ + + ks8851_wrreg16(ks, KS_RXCR1, (RXCR1_RXPAFMA | /* from mac filter */ + RXCR1_RXFCE | /* enable flow control */ + RXCR1_RXBE | /* broadcast enable */ + RXCR1_RXUE | /* unicast enable */ + RXCR1_RXE)); /* enable rx block */ + + /* transfer entire frames out in one go */ + ks8851_wrreg16(ks, KS_RXCR2, RXCR2_SRDBL_FRAME); + + /* set receive counter timeouts */ + ks8851_wrreg16(ks, KS_RXDTTR, 1000); /* 1ms after first frame to IRQ */ + ks8851_wrreg16(ks, KS_RXDBCTR, 4096); /* >4Kbytes in buffer to IRQ */ + ks8851_wrreg16(ks, KS_RXFCTR, 10); /* 10 frames to IRQ */ + + ks->rc_rxqcr = (RXQCR_RXFCTE | /* IRQ on frame count exceeded */ + RXQCR_RXDBCTE | /* IRQ on byte count exceeded */ + RXQCR_RXDTTE); /* IRQ on time exceeded */ + + ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr); + + /* clear then enable interrupts */ + +#define STD_IRQ (IRQ_LCI | /* Link Change */ \ + IRQ_TXI | /* TX done */ \ + IRQ_RXI | /* RX done */ \ + IRQ_SPIBEI | /* SPI bus error */ \ + IRQ_TXPSI | /* TX process stop */ \ + IRQ_RXPSI) /* RX process stop */ + + ks->rc_ier = STD_IRQ; + ks8851_wrreg16(ks, KS_ISR, STD_IRQ); + ks8851_wrreg16(ks, KS_IER, STD_IRQ); + + netif_start_queue(ks->netdev); + + if (netif_msg_ifup(ks)) + ks_dbg(ks, "network device %s up\n", dev->name); + + mutex_unlock(&ks->lock); + return 0; +} + +/** + * ks8851_net_stop - close network device + * @dev: The device being closed. + * + * Called to close down a network device which has been active. Cancell any + * work, shutdown the RX and TX process and then place the chip into a low + * power state whilst it is not being used. + */ +static int ks8851_net_stop(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + + if (netif_msg_ifdown(ks)) + ks_info(ks, "%s: shutting down\n", dev->name); + + netif_stop_queue(dev); + + mutex_lock(&ks->lock); + + /* stop any outstanding work */ + flush_work(&ks->irq_work); + flush_work(&ks->tx_work); + flush_work(&ks->rxctrl_work); + + /* turn off the IRQs and ack any outstanding */ + ks8851_wrreg16(ks, KS_IER, 0x0000); + ks8851_wrreg16(ks, KS_ISR, 0xffff); + + /* shutdown RX process */ + ks8851_wrreg16(ks, KS_RXCR1, 0x0000); + + /* shutdown TX process */ + ks8851_wrreg16(ks, KS_TXCR, 0x0000); + + /* set powermode to soft power down to save power */ + ks8851_set_powermode(ks, PMECR_PM_SOFTDOWN); + + /* ensure any queued tx buffers are dumped */ + while (!skb_queue_empty(&ks->txq)) { + struct sk_buff *txb = skb_dequeue(&ks->txq); + + if (netif_msg_ifdown(ks)) + ks_dbg(ks, "%s: freeing txb %p\n", __func__, txb); + + dev_kfree_skb(txb); + } + + mutex_unlock(&ks->lock); + return 0; +} + +/** + * ks8851_start_xmit - transmit packet + * @skb: The buffer to transmit + * @dev: The device used to transmit the packet. + * + * Called by the network layer to transmit the @skb. Queue the packet for + * the device and schedule the necessary work to transmit the packet when + * it is free. + * + * We do this to firstly avoid sleeping with the network device locked, + * and secondly so we can round up more than one packet to transmit which + * means we can try and avoid generating too many transmit done interrupts. + */ +static int ks8851_start_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + unsigned needed = calc_txlen(skb->len); + int ret = NETDEV_TX_OK; + + if (netif_msg_tx_queued(ks)) + ks_dbg(ks, "%s: skb %p, %d@%p\n", __func__, + skb, skb->len, skb->data); + + spin_lock(&ks->statelock); + + if (needed > ks->tx_space) { + netif_stop_queue(dev); + ret = NETDEV_TX_BUSY; + } else { + ks->tx_space -= needed; + skb_queue_tail(&ks->txq, skb); + } + + spin_unlock(&ks->statelock); + schedule_work(&ks->tx_work); + + return ret; +} + +/** + * ks8851_rxctrl_work - work handler to change rx mode + * @work: The work structure this belongs to. + * + * Lock the device and issue the necessary changes to the receive mode from + * the network device layer. This is done so that we can do this without + * having to sleep whilst holding the network device lock. + * + * Since the recommendation from Micrel is that the RXQ is shutdown whilst the + * receive parameters are programmed, we issue a write to disable the RXQ and + * then wait for the interrupt handler to be triggered once the RXQ shutdown is + * complete. The interrupt handler then writes the new values into the chip. + */ +static void ks8851_rxctrl_work(struct work_struct *work) +{ + struct ks8851_net *ks = container_of(work, struct ks8851_net, rxctrl_work); + + mutex_lock(&ks->lock); + + /* need to shutdown RXQ before modifying filter parameters */ + ks8851_wrreg16(ks, KS_RXCR1, 0x00); + + mutex_unlock(&ks->lock); +} + +static void ks8851_set_rx_mode(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + struct ks8851_rxctrl rxctrl; + + memset(&rxctrl, 0, sizeof(rxctrl)); + + if (dev->flags & IFF_PROMISC) { + /* interface to receive everything */ + + rxctrl.rxcr1 = RXCR1_RXAE | RXCR1_RXINVF; + } else if (dev->flags & IFF_ALLMULTI) { + /* accept all multicast packets */ + + rxctrl.rxcr1 = (RXCR1_RXME | RXCR1_RXAE | + RXCR1_RXPAFMA | RXCR1_RXMAFMA); + } else if (dev->flags & IFF_MULTICAST && dev->mc_count > 0) { + struct dev_mc_list *mcptr = dev->mc_list; + u32 crc; + int i; + + /* accept some multicast */ + + for (i = dev->mc_count; i > 0; i--) { + crc = ether_crc(ETH_ALEN, mcptr->dmi_addr); + crc >>= (32 - 6); /* get top six bits */ + + rxctrl.mchash[crc >> 4] |= (1 << (crc & 0xf)); + mcptr = mcptr->next; + } + + rxctrl.rxcr1 = RXCR1_RXME | RXCR1_RXAE | RXCR1_RXPAFMA; + } else { + /* just accept broadcast / unicast */ + rxctrl.rxcr1 = RXCR1_RXPAFMA; + } + + rxctrl.rxcr1 |= (RXCR1_RXUE | /* unicast enable */ + RXCR1_RXBE | /* broadcast enable */ + RXCR1_RXE | /* RX process enable */ + RXCR1_RXFCE); /* enable flow control */ + + rxctrl.rxcr2 |= RXCR2_SRDBL_FRAME; + + /* schedule work to do the actual set of the data if needed */ + + spin_lock(&ks->statelock); + + if (memcmp(&rxctrl, &ks->rxctrl, sizeof(rxctrl)) != 0) { + memcpy(&ks->rxctrl, &rxctrl, sizeof(ks->rxctrl)); + schedule_work(&ks->rxctrl_work); + } + + spin_unlock(&ks->statelock); +} + +static int ks8851_set_mac_address(struct net_device *dev, void *addr) +{ + struct sockaddr *sa = addr; + + if (netif_running(dev)) + return -EBUSY; + + if (!is_valid_ether_addr(sa->sa_data)) + return -EADDRNOTAVAIL; + + memcpy(dev->dev_addr, sa->sa_data, ETH_ALEN); + return ks8851_write_mac_addr(dev); +} + +static int ks8851_net_ioctl(struct net_device *dev, struct ifreq *req, int cmd) +{ + struct ks8851_net *ks = netdev_priv(dev); + + if (!netif_running(dev)) + return -EINVAL; + + return generic_mii_ioctl(&ks->mii, if_mii(req), cmd, NULL); +} + +static const struct net_device_ops ks8851_netdev_ops = { + .ndo_open = ks8851_net_open, + .ndo_stop = ks8851_net_stop, + .ndo_do_ioctl = ks8851_net_ioctl, + .ndo_start_xmit = ks8851_start_xmit, + .ndo_set_mac_address = ks8851_set_mac_address, + .ndo_set_rx_mode = ks8851_set_rx_mode, + .ndo_change_mtu = eth_change_mtu, + .ndo_validate_addr = eth_validate_addr, +}; + +/* ethtool support */ + +static void ks8851_get_drvinfo(struct net_device *dev, + struct ethtool_drvinfo *di) +{ + strlcpy(di->driver, "KS8851", sizeof(di->driver)); + strlcpy(di->version, "1.00", sizeof(di->version)); + strlcpy(di->bus_info, dev_name(dev->dev.parent), sizeof(di->bus_info)); +} + +static u32 ks8851_get_msglevel(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + return ks->msg_enable; +} + +static void ks8851_set_msglevel(struct net_device *dev, u32 to) +{ + struct ks8851_net *ks = netdev_priv(dev); + ks->msg_enable = to; +} + +static int ks8851_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct ks8851_net *ks = netdev_priv(dev); + return mii_ethtool_gset(&ks->mii, cmd); +} + +static int ks8851_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct ks8851_net *ks = netdev_priv(dev); + return mii_ethtool_sset(&ks->mii, cmd); +} + +static u32 ks8851_get_link(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + return mii_link_ok(&ks->mii); +} + +static int ks8851_nway_reset(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + return mii_nway_restart(&ks->mii); +} + +static const struct ethtool_ops ks8851_ethtool_ops = { + .get_drvinfo = ks8851_get_drvinfo, + .get_msglevel = ks8851_get_msglevel, + .set_msglevel = ks8851_set_msglevel, + .get_settings = ks8851_get_settings, + .set_settings = ks8851_set_settings, + .get_link = ks8851_get_link, + .nway_reset = ks8851_nway_reset, +}; + +/* MII interface controls */ + +/** + * ks8851_phy_reg - convert MII register into a KS8851 register + * @reg: MII register number. + * + * Return the KS8851 register number for the corresponding MII PHY register + * if possible. Return zero if the MII register has no direct mapping to the + * KS8851 register set. + */ +static int ks8851_phy_reg(int reg) +{ + switch (reg) { + case MII_BMCR: + return KS_P1MBCR; + case MII_BMSR: + return KS_P1MBSR; + case MII_PHYSID1: + return KS_PHY1ILR; + case MII_PHYSID2: + return KS_PHY1IHR; + case MII_ADVERTISE: + return KS_P1ANAR; + case MII_LPA: + return KS_P1ANLPR; + } + + return 0x0; +} + +/** + * ks8851_phy_read - MII interface PHY register read. + * @dev: The network device the PHY is on. + * @phy_addr: Address of PHY (ignored as we only have one) + * @reg: The register to read. + * + * This call reads data from the PHY register specified in @reg. Since the + * device does not support all the MII registers, the non-existant values + * are always returned as zero. + * + * We return zero for unsupported registers as the MII code does not check + * the value returned for any error status, and simply returns it to the + * caller. The mii-tool that the driver was tested with takes any -ve error + * as real PHY capabilities, thus displaying incorrect data to the user. + */ +static int ks8851_phy_read(struct net_device *dev, int phy_addr, int reg) +{ + struct ks8851_net *ks = netdev_priv(dev); + int ksreg; + int result; + + ksreg = ks8851_phy_reg(reg); + if (!ksreg) + return 0x0; /* no error return allowed, so use zero */ + + mutex_lock(&ks->lock); + result = ks8851_rdreg16(ks, ksreg); + mutex_unlock(&ks->lock); + + return result; +} + +static void ks8851_phy_write(struct net_device *dev, + int phy, int reg, int value) +{ + struct ks8851_net *ks = netdev_priv(dev); + int ksreg; + + ksreg = ks8851_phy_reg(reg); + if (ksreg) { + mutex_lock(&ks->lock); + ks8851_wrreg16(ks, ksreg, value); + mutex_unlock(&ks->lock); + } +} + +/** + * ks8851_read_selftest - read the selftest memory info. + * @ks: The device state + * + * Read and check the TX/RX memory selftest information. + */ +static int ks8851_read_selftest(struct ks8851_net *ks) +{ + unsigned both_done = MBIR_TXMBF | MBIR_RXMBF; + int ret = 0; + unsigned rd; + + rd = ks8851_rdreg16(ks, KS_MBIR); + + if ((rd & both_done) != both_done) { + ks_warn(ks, "Memory selftest not finished\n"); + return 0; + } + + if (rd & MBIR_TXMBFA) { + ks_err(ks, "TX memory selftest fail\n"); + ret |= 1; + } + + if (rd & MBIR_RXMBFA) { + ks_err(ks, "RX memory selftest fail\n"); + ret |= 2; + } + + return 0; +} + +/* driver bus management functions */ + +static int __devinit ks8851_probe(struct spi_device *spi) +{ + struct net_device *ndev; + struct ks8851_net *ks; + int ret; + + ndev = alloc_etherdev(sizeof(struct ks8851_net)); + if (!ndev) { + dev_err(&spi->dev, "failed to alloc ethernet device\n"); + return -ENOMEM; + } + + spi->bits_per_word = 8; + + ks = netdev_priv(ndev); + + ks->netdev = ndev; + ks->spidev = spi; + ks->tx_space = 6144; + + mutex_init(&ks->lock); + spin_lock_init(&ks->statelock); + + INIT_WORK(&ks->tx_work, ks8851_tx_work); + INIT_WORK(&ks->irq_work, ks8851_irq_work); + INIT_WORK(&ks->rxctrl_work, ks8851_rxctrl_work); + + /* initialise pre-made spi transfer messages */ + + spi_message_init(&ks->spi_msg1); + spi_message_add_tail(&ks->spi_xfer1, &ks->spi_msg1); + + spi_message_init(&ks->spi_msg2); + spi_message_add_tail(&ks->spi_xfer2[0], &ks->spi_msg2); + spi_message_add_tail(&ks->spi_xfer2[1], &ks->spi_msg2); + + /* setup mii state */ + ks->mii.dev = ndev; + ks->mii.phy_id = 1, + ks->mii.phy_id_mask = 1; + ks->mii.reg_num_mask = 0xf; + ks->mii.mdio_read = ks8851_phy_read; + ks->mii.mdio_write = ks8851_phy_write; + + dev_info(&spi->dev, "message enable is %d\n", msg_enable); + + /* set the default message enable */ + ks->msg_enable = netif_msg_init(msg_enable, (NETIF_MSG_DRV | + NETIF_MSG_PROBE | + NETIF_MSG_LINK)); + + skb_queue_head_init(&ks->txq); + + SET_ETHTOOL_OPS(ndev, &ks8851_ethtool_ops); + SET_NETDEV_DEV(ndev, &spi->dev); + + dev_set_drvdata(&spi->dev, ks); + + ndev->if_port = IF_PORT_100BASET; + ndev->netdev_ops = &ks8851_netdev_ops; + ndev->irq = spi->irq; + + /* simple check for a valid chip being connected to the bus */ + + if ((ks8851_rdreg16(ks, KS_CIDER) & ~CIDER_REV_MASK) != CIDER_ID) { + dev_err(&spi->dev, "failed to read device ID\n"); + ret = -ENODEV; + goto err_id; + } + + ks8851_read_selftest(ks); + ks8851_init_mac(ks); + + ret = request_irq(spi->irq, ks8851_irq, IRQF_TRIGGER_LOW, + ndev->name, ks); + if (ret < 0) { + dev_err(&spi->dev, "failed to get irq\n"); + goto err_irq; + } + + ret = register_netdev(ndev); + if (ret) { + dev_err(&spi->dev, "failed to register network device\n"); + goto err_netdev; + } + + dev_info(&spi->dev, "revision %d, MAC %pM, IRQ %d\n", + CIDER_REV_GET(ks8851_rdreg16(ks, KS_CIDER)), + ndev->dev_addr, ndev->irq); + + return 0; + + +err_netdev: + free_irq(ndev->irq, ndev); + +err_id: +err_irq: + free_netdev(ndev); + return ret; +} + +static int __devexit ks8851_remove(struct spi_device *spi) +{ + struct ks8851_net *priv = dev_get_drvdata(&spi->dev); + + if (netif_msg_drv(priv)) + dev_info(&spi->dev, "remove"); + + unregister_netdev(priv->netdev); + free_irq(spi->irq, priv); + free_netdev(priv->netdev); + + return 0; +} + +static struct spi_driver ks8851_driver = { + .driver = { + .name = "ks8851", + .owner = THIS_MODULE, + }, + .probe = ks8851_probe, + .remove = __devexit_p(ks8851_remove), +}; + +static int __init ks8851_init(void) +{ + return spi_register_driver(&ks8851_driver); +} + +static void __exit ks8851_exit(void) +{ + spi_unregister_driver(&ks8851_driver); +} + +module_init(ks8851_init); +module_exit(ks8851_exit); + +MODULE_DESCRIPTION("KS8851 Network driver"); +MODULE_AUTHOR("Ben Dooks "); +MODULE_LICENSE("GPL"); + +module_param_named(message, msg_enable, int, 0); +MODULE_PARM_DESC(message, "Message verbosity level (0=none, 31=all)"); diff --git a/drivers/net/ks8851.h b/drivers/net/ks8851.h new file mode 100644 index 00000000000..85abe147afb --- /dev/null +++ b/drivers/net/ks8851.h @@ -0,0 +1,296 @@ +/* drivers/net/ks8851.h + * + * Copyright 2009 Simtec Electronics + * Ben Dooks + * + * KS8851 register definitions + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#define KS_CCR 0x08 +#define CCR_EEPROM (1 << 9) +#define CCR_SPI (1 << 8) +#define CCR_32PIN (1 << 0) + +/* MAC address registers */ +#define KS_MARL 0x10 +#define KS_MARM 0x12 +#define KS_MARH 0x14 + +#define KS_OBCR 0x20 +#define OBCR_ODS_16mA (1 << 6) + +#define KS_EEPCR 0x22 +#define EEPCR_EESA (1 << 4) +#define EEPCR_EESB (1 << 3) +#define EEPCR_EEDO (1 << 2) +#define EEPCR_EESCK (1 << 1) +#define EEPCR_EECS (1 << 0) + +#define KS_MBIR 0x24 +#define MBIR_TXMBF (1 << 12) +#define MBIR_TXMBFA (1 << 11) +#define MBIR_RXMBF (1 << 4) +#define MBIR_RXMBFA (1 << 3) + +#define KS_GRR 0x26 +#define GRR_QMU (1 << 1) +#define GRR_GSR (1 << 0) + +#define KS_WFCR 0x2A +#define WFCR_MPRXE (1 << 7) +#define WFCR_WF3E (1 << 3) +#define WFCR_WF2E (1 << 2) +#define WFCR_WF1E (1 << 1) +#define WFCR_WF0E (1 << 0) + +#define KS_WF0CRC0 0x30 +#define KS_WF0CRC1 0x32 +#define KS_WF0BM0 0x34 +#define KS_WF0BM1 0x36 +#define KS_WF0BM2 0x38 +#define KS_WF0BM3 0x3A + +#define KS_WF1CRC0 0x40 +#define KS_WF1CRC1 0x42 +#define KS_WF1BM0 0x44 +#define KS_WF1BM1 0x46 +#define KS_WF1BM2 0x48 +#define KS_WF1BM3 0x4A + +#define KS_WF2CRC0 0x50 +#define KS_WF2CRC1 0x52 +#define KS_WF2BM0 0x54 +#define KS_WF2BM1 0x56 +#define KS_WF2BM2 0x58 +#define KS_WF2BM3 0x5A + +#define KS_WF3CRC0 0x60 +#define KS_WF3CRC1 0x62 +#define KS_WF3BM0 0x64 +#define KS_WF3BM1 0x66 +#define KS_WF3BM2 0x68 +#define KS_WF3BM3 0x6A + +#define KS_TXCR 0x70 +#define TXCR_TCGICMP (1 << 8) +#define TXCR_TCGUDP (1 << 7) +#define TXCR_TCGTCP (1 << 6) +#define TXCR_TCGIP (1 << 5) +#define TXCR_FTXQ (1 << 4) +#define TXCR_TXFCE (1 << 3) +#define TXCR_TXPE (1 << 2) +#define TXCR_TXCRC (1 << 1) +#define TXCR_TXE (1 << 0) + +#define KS_TXSR 0x72 +#define TXSR_TXLC (1 << 13) +#define TXSR_TXMC (1 << 12) +#define TXSR_TXFID_MASK (0x3f << 0) +#define TXSR_TXFID_SHIFT (0) +#define TXSR_TXFID_GET(_v) (((_v) >> 0) & 0x3f) + +#define KS_RXCR1 0x74 +#define RXCR1_FRXQ (1 << 15) +#define RXCR1_RXUDPFCC (1 << 14) +#define RXCR1_RXTCPFCC (1 << 13) +#define RXCR1_RXIPFCC (1 << 12) +#define RXCR1_RXPAFMA (1 << 11) +#define RXCR1_RXFCE (1 << 10) +#define RXCR1_RXEFE (1 << 9) +#define RXCR1_RXMAFMA (1 << 8) +#define RXCR1_RXBE (1 << 7) +#define RXCR1_RXME (1 << 6) +#define RXCR1_RXUE (1 << 5) +#define RXCR1_RXAE (1 << 4) +#define RXCR1_RXINVF (1 << 1) +#define RXCR1_RXE (1 << 0) + +#define KS_RXCR2 0x76 +#define RXCR2_SRDBL_MASK (0x7 << 5) +#define RXCR2_SRDBL_SHIFT (5) +#define RXCR2_SRDBL_4B (0x0 << 5) +#define RXCR2_SRDBL_8B (0x1 << 5) +#define RXCR2_SRDBL_16B (0x2 << 5) +#define RXCR2_SRDBL_32B (0x3 << 5) +#define RXCR2_SRDBL_FRAME (0x4 << 5) +#define RXCR2_IUFFP (1 << 4) +#define RXCR2_RXIUFCEZ (1 << 3) +#define RXCR2_UDPLFE (1 << 2) +#define RXCR2_RXICMPFCC (1 << 1) +#define RXCR2_RXSAF (1 << 0) + +#define KS_TXMIR 0x78 + +#define KS_RXFHSR 0x7C +#define RXFSHR_RXFV (1 << 15) +#define RXFSHR_RXICMPFCS (1 << 13) +#define RXFSHR_RXIPFCS (1 << 12) +#define RXFSHR_RXTCPFCS (1 << 11) +#define RXFSHR_RXUDPFCS (1 << 10) +#define RXFSHR_RXBF (1 << 7) +#define RXFSHR_RXMF (1 << 6) +#define RXFSHR_RXUF (1 << 5) +#define RXFSHR_RXMR (1 << 4) +#define RXFSHR_RXFT (1 << 3) +#define RXFSHR_RXFTL (1 << 2) +#define RXFSHR_RXRF (1 << 1) +#define RXFSHR_RXCE (1 << 0) + +#define KS_RXFHBCR 0x7E +#define KS_TXQCR 0x80 +#define TXQCR_AETFE (1 << 2) +#define TXQCR_TXQMAM (1 << 1) +#define TXQCR_METFE (1 << 0) + +#define KS_RXQCR 0x82 +#define RXQCR_RXDTTS (1 << 12) +#define RXQCR_RXDBCTS (1 << 11) +#define RXQCR_RXFCTS (1 << 10) +#define RXQCR_RXIPHTOE (1 << 9) +#define RXQCR_RXDTTE (1 << 7) +#define RXQCR_RXDBCTE (1 << 6) +#define RXQCR_RXFCTE (1 << 5) +#define RXQCR_ADRFE (1 << 4) +#define RXQCR_SDA (1 << 3) +#define RXQCR_RRXEF (1 << 0) + +#define KS_TXFDPR 0x84 +#define TXFDPR_TXFPAI (1 << 14) +#define TXFDPR_TXFP_MASK (0x7ff << 0) +#define TXFDPR_TXFP_SHIFT (0) + +#define KS_RXFDPR 0x86 +#define RXFDPR_RXFPAI (1 << 14) + +#define KS_RXDTTR 0x8C +#define KS_RXDBCTR 0x8E + +#define KS_IER 0x90 +#define KS_ISR 0x92 +#define IRQ_LCI (1 << 15) +#define IRQ_TXI (1 << 14) +#define IRQ_RXI (1 << 13) +#define IRQ_RXOI (1 << 11) +#define IRQ_TXPSI (1 << 9) +#define IRQ_RXPSI (1 << 8) +#define IRQ_TXSAI (1 << 6) +#define IRQ_RXWFDI (1 << 5) +#define IRQ_RXMPDI (1 << 4) +#define IRQ_LDI (1 << 3) +#define IRQ_EDI (1 << 2) +#define IRQ_SPIBEI (1 << 1) +#define IRQ_DEDI (1 << 0) + +#define KS_RXFCTR 0x9C +#define KS_RXFC 0x9D +#define RXFCTR_RXFC_MASK (0xff << 8) +#define RXFCTR_RXFC_SHIFT (8) +#define RXFCTR_RXFC_GET(_v) (((_v) >> 8) & 0xff) +#define RXFCTR_RXFCT_MASK (0xff << 0) +#define RXFCTR_RXFCT_SHIFT (0) + +#define KS_TXNTFSR 0x9E + +#define KS_MAHTR0 0xA0 +#define KS_MAHTR1 0xA2 +#define KS_MAHTR2 0xA4 +#define KS_MAHTR3 0xA6 + +#define KS_FCLWR 0xB0 +#define KS_FCHWR 0xB2 +#define KS_FCOWR 0xB4 + +#define KS_CIDER 0xC0 +#define CIDER_ID 0x8870 +#define CIDER_REV_MASK (0x7 << 1) +#define CIDER_REV_SHIFT (1) +#define CIDER_REV_GET(_v) (((_v) >> 1) & 0x7) + +#define KS_CGCR 0xC6 + +#define KS_IACR 0xC8 +#define IACR_RDEN (1 << 12) +#define IACR_TSEL_MASK (0x3 << 10) +#define IACR_TSEL_SHIFT (10) +#define IACR_TSEL_MIB (0x3 << 10) +#define IACR_ADDR_MASK (0x1f << 0) +#define IACR_ADDR_SHIFT (0) + +#define KS_IADLR 0xD0 +#define KS_IAHDR 0xD2 + +#define KS_PMECR 0xD4 +#define PMECR_PME_DELAY (1 << 14) +#define PMECR_PME_POL (1 << 12) +#define PMECR_WOL_WAKEUP (1 << 11) +#define PMECR_WOL_MAGICPKT (1 << 10) +#define PMECR_WOL_LINKUP (1 << 9) +#define PMECR_WOL_ENERGY (1 << 8) +#define PMECR_AUTO_WAKE_EN (1 << 7) +#define PMECR_WAKEUP_NORMAL (1 << 6) +#define PMECR_WKEVT_MASK (0xf << 2) +#define PMECR_WKEVT_SHIFT (2) +#define PMECR_WKEVT_GET(_v) (((_v) >> 2) & 0xf) +#define PMECR_WKEVT_ENERGY (0x1 << 2) +#define PMECR_WKEVT_LINK (0x2 << 2) +#define PMECR_WKEVT_MAGICPKT (0x4 << 2) +#define PMECR_WKEVT_FRAME (0x8 << 2) +#define PMECR_PM_MASK (0x3 << 0) +#define PMECR_PM_SHIFT (0) +#define PMECR_PM_NORMAL (0x0 << 0) +#define PMECR_PM_ENERGY (0x1 << 0) +#define PMECR_PM_SOFTDOWN (0x2 << 0) +#define PMECR_PM_POWERSAVE (0x3 << 0) + +/* Standard MII PHY data */ +#define KS_P1MBCR 0xE4 +#define KS_P1MBSR 0xE6 +#define KS_PHY1ILR 0xE8 +#define KS_PHY1IHR 0xEA +#define KS_P1ANAR 0xEC +#define KS_P1ANLPR 0xEE + +#define KS_P1SCLMD 0xF4 +#define P1SCLMD_LEDOFF (1 << 15) +#define P1SCLMD_TXIDS (1 << 14) +#define P1SCLMD_RESTARTAN (1 << 13) +#define P1SCLMD_DISAUTOMDIX (1 << 10) +#define P1SCLMD_FORCEMDIX (1 << 9) +#define P1SCLMD_AUTONEGEN (1 << 7) +#define P1SCLMD_FORCE100 (1 << 6) +#define P1SCLMD_FORCEFDX (1 << 5) +#define P1SCLMD_ADV_FLOW (1 << 4) +#define P1SCLMD_ADV_100BT_FDX (1 << 3) +#define P1SCLMD_ADV_100BT_HDX (1 << 2) +#define P1SCLMD_ADV_10BT_FDX (1 << 1) +#define P1SCLMD_ADV_10BT_HDX (1 << 0) + +#define KS_P1CR 0xF6 +#define P1CR_HP_MDIX (1 << 15) +#define P1CR_REV_POL (1 << 13) +#define P1CR_OP_100M (1 << 10) +#define P1CR_OP_FDX (1 << 9) +#define P1CR_OP_MDI (1 << 7) +#define P1CR_AN_DONE (1 << 6) +#define P1CR_LINK_GOOD (1 << 5) +#define P1CR_PNTR_FLOW (1 << 4) +#define P1CR_PNTR_100BT_FDX (1 << 3) +#define P1CR_PNTR_100BT_HDX (1 << 2) +#define P1CR_PNTR_10BT_FDX (1 << 1) +#define P1CR_PNTR_10BT_HDX (1 << 0) + +/* TX Frame control */ + +#define TXFR_TXIC (1 << 15) +#define TXFR_TXFID_MASK (0x3f << 0) +#define TXFR_TXFID_SHIFT (0) + +/* SPI frame opcodes */ +#define KS_SPIOP_RD (0x00) +#define KS_SPIOP_WR (0x40) +#define KS_SPIOP_RXFIFO (0x80) +#define KS_SPIOP_TXFIFO (0xC0) -- GitLab From cf981ffb31e8f41f4899a56560f81322f94f22d1 Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Fri, 17 Jul 2009 15:27:06 +0000 Subject: [PATCH 0115/1342] netxen: fix context deletion sequence o Use D3 reset context deletion for NX2031, it cleans up more resources in the firmware. o Release rx buffers after hardware context has been reset. o Delete tx context after rx context, some firmware control commands are sent on tx context, so it should be the last to go. Signed-off-by: Dhananjay Phadke Signed-off-by: David S. Miller --- drivers/net/netxen/netxen_nic.h | 1 + drivers/net/netxen/netxen_nic_ctx.c | 13 +++++++------ drivers/net/netxen/netxen_nic_main.c | 2 +- 3 files changed, 9 insertions(+), 7 deletions(-) diff --git a/drivers/net/netxen/netxen_nic.h b/drivers/net/netxen/netxen_nic.h index e1cdba752e0..9fa71faf4ce 100644 --- a/drivers/net/netxen/netxen_nic.h +++ b/drivers/net/netxen/netxen_nic.h @@ -210,6 +210,7 @@ #define NETXEN_CTX_SIGNATURE 0xdee0 #define NETXEN_CTX_SIGNATURE_V2 0x0002dee0 #define NETXEN_CTX_RESET 0xbad0 +#define NETXEN_CTX_D3_RESET 0xacc0 #define NETXEN_RCV_PRODUCER(ringid) (ringid) #define PHAN_PEG_RCV_INITIALIZED 0xff01 diff --git a/drivers/net/netxen/netxen_nic_ctx.c b/drivers/net/netxen/netxen_nic_ctx.c index 4754f5cffad..9f8ae4719e2 100644 --- a/drivers/net/netxen/netxen_nic_ctx.c +++ b/drivers/net/netxen/netxen_nic_ctx.c @@ -684,10 +684,8 @@ int netxen_alloc_hw_resources(struct netxen_adapter *adapter) goto err_out_free; } else { err = netxen_init_old_ctx(adapter); - if (err) { - netxen_free_hw_resources(adapter); - return err; - } + if (err) + goto err_out_free; } return 0; @@ -708,15 +706,18 @@ void netxen_free_hw_resources(struct netxen_adapter *adapter) int port = adapter->portnum; if (adapter->fw_major >= 4) { - nx_fw_cmd_destroy_tx_ctx(adapter); nx_fw_cmd_destroy_rx_ctx(adapter); + nx_fw_cmd_destroy_tx_ctx(adapter); } else { netxen_api_lock(adapter); NXWR32(adapter, CRB_CTX_SIGNATURE_REG(port), - NETXEN_CTX_RESET | port); + NETXEN_CTX_D3_RESET | port); netxen_api_unlock(adapter); } + /* Allow dma queues to drain after context reset */ + msleep(20); + recv_ctx = &adapter->recv_ctx; if (recv_ctx->hwctx != NULL) { diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index 27539ddf94c..9a7c4c8029d 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -943,8 +943,8 @@ err_out_free_sw: static void netxen_nic_detach(struct netxen_adapter *adapter) { - netxen_release_rx_buffers(adapter); netxen_free_hw_resources(adapter); + netxen_release_rx_buffers(adapter); netxen_nic_free_irq(adapter); netxen_free_sw_resources(adapter); -- GitLab From b2af9cb06d4de1b507ec0fd779ec2ecedee1480a Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Fri, 17 Jul 2009 15:27:07 +0000 Subject: [PATCH 0116/1342] netxen: fix deadlock on dev close netxen: fix deadlock on dev close The tx ring accounting fix in commit cb2107be43d2fc5eadec58b92b ("netxen: fix tx ring accounting") introduced intermittent deadlock when inteface is going down. This was possibly combined effect of speculative tx pause, calling netif_tx_lock instead of queue lock and unclean synchronization with napi which could end up unmasking interrupt. Signed-off-by: Dhananjay Phadke Signed-off-by: David S. Miller --- drivers/net/netxen/netxen_nic.h | 2 ++ drivers/net/netxen/netxen_nic_hw.c | 9 +++++---- drivers/net/netxen/netxen_nic_init.c | 5 +++-- drivers/net/netxen/netxen_nic_main.c | 20 +++++++++++++------- 4 files changed, 23 insertions(+), 13 deletions(-) diff --git a/drivers/net/netxen/netxen_nic.h b/drivers/net/netxen/netxen_nic.h index 9fa71faf4ce..f86e05047d1 100644 --- a/drivers/net/netxen/netxen_nic.h +++ b/drivers/net/netxen/netxen_nic.h @@ -774,6 +774,8 @@ struct nx_host_tx_ring { u32 crb_cmd_consumer; u32 num_desc; + struct netdev_queue *txq; + struct netxen_cmd_buffer *cmd_buf_arr; struct cmd_desc_type0 *desc_head; dma_addr_t phys_addr; diff --git a/drivers/net/netxen/netxen_nic_hw.c b/drivers/net/netxen/netxen_nic_hw.c index ce3b89d2cbb..b9123d445c9 100644 --- a/drivers/net/netxen/netxen_nic_hw.c +++ b/drivers/net/netxen/netxen_nic_hw.c @@ -461,13 +461,14 @@ netxen_send_cmd_descs(struct netxen_adapter *adapter, i = 0; tx_ring = adapter->tx_ring; - netif_tx_lock_bh(adapter->netdev); + __netif_tx_lock_bh(tx_ring->txq); producer = tx_ring->producer; consumer = tx_ring->sw_consumer; - if (nr_desc >= find_diff_among(producer, consumer, tx_ring->num_desc)) { - netif_tx_unlock_bh(adapter->netdev); + if (nr_desc >= netxen_tx_avail(tx_ring)) { + netif_tx_stop_queue(tx_ring->txq); + __netif_tx_unlock_bh(tx_ring->txq); return -EBUSY; } @@ -490,7 +491,7 @@ netxen_send_cmd_descs(struct netxen_adapter *adapter, netxen_nic_update_cmd_producer(adapter, tx_ring); - netif_tx_unlock_bh(adapter->netdev); + __netif_tx_unlock_bh(tx_ring->txq); return 0; } diff --git a/drivers/net/netxen/netxen_nic_init.c b/drivers/net/netxen/netxen_nic_init.c index b899bd51fcd..5d3343ef3d8 100644 --- a/drivers/net/netxen/netxen_nic_init.c +++ b/drivers/net/netxen/netxen_nic_init.c @@ -214,6 +214,7 @@ int netxen_alloc_sw_resources(struct netxen_adapter *adapter) adapter->tx_ring = tx_ring; tx_ring->num_desc = adapter->num_txd; + tx_ring->txq = netdev_get_tx_queue(netdev, 0); cmd_buf_arr = vmalloc(TX_BUFF_RINGSIZE(tx_ring)); if (cmd_buf_arr == NULL) { @@ -1400,10 +1401,10 @@ int netxen_process_cmd_ring(struct netxen_adapter *adapter) smp_mb(); if (netif_queue_stopped(netdev) && netif_carrier_ok(netdev)) { - netif_tx_lock(netdev); + __netif_tx_lock(tx_ring->txq, smp_processor_id()); if (netxen_tx_avail(tx_ring) > TX_STOP_THRESH) netif_wake_queue(netdev); - netif_tx_unlock(netdev); + __netif_tx_unlock(tx_ring->txq); } } /* diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index 9a7c4c8029d..370c52f2776 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -215,9 +215,9 @@ netxen_napi_disable(struct netxen_adapter *adapter) for (ring = 0; ring < adapter->max_sds_rings; ring++) { sds_ring = &recv_ctx->sds_rings[ring]; - napi_disable(&sds_ring->napi); netxen_nic_disable_int(sds_ring); - synchronize_irq(sds_ring->irq); + napi_synchronize(&sds_ring->napi); + napi_disable(&sds_ring->napi); } } @@ -833,11 +833,11 @@ netxen_nic_up(struct netxen_adapter *adapter, struct net_device *netdev) adapter->ahw.linkup = 0; - netxen_napi_enable(adapter); - if (adapter->max_sds_rings > 1) netxen_config_rss(adapter, 1); + netxen_napi_enable(adapter); + if (adapter->capabilities & NX_FW_CAPABILITY_LINK_NOTIFICATION) netxen_linkevent_request(adapter, 1); else @@ -851,8 +851,9 @@ netxen_nic_up(struct netxen_adapter *adapter, struct net_device *netdev) static void netxen_nic_down(struct netxen_adapter *adapter, struct net_device *netdev) { + spin_lock(&adapter->tx_clean_lock); netif_carrier_off(netdev); - netif_stop_queue(netdev); + netif_tx_disable(netdev); if (adapter->stop_port) adapter->stop_port(adapter); @@ -863,9 +864,10 @@ netxen_nic_down(struct netxen_adapter *adapter, struct net_device *netdev) netxen_napi_disable(adapter); netxen_release_tx_buffers(adapter); + spin_unlock(&adapter->tx_clean_lock); - FLUSH_SCHEDULED_WORK(); del_timer_sync(&adapter->watchdog_timer); + FLUSH_SCHEDULED_WORK(); } @@ -1645,6 +1647,9 @@ static void netxen_tx_timeout_task(struct work_struct *work) struct netxen_adapter *adapter = container_of(work, struct netxen_adapter, tx_timeout_task); + if (!netif_running(adapter->netdev)) + return; + printk(KERN_ERR "%s %s: transmit timeout, resetting.\n", netxen_nic_driver_name, adapter->netdev->name); @@ -1757,7 +1762,8 @@ static int netxen_nic_poll(struct napi_struct *napi, int budget) if ((work_done < budget) && tx_complete) { napi_complete(&sds_ring->napi); - netxen_nic_enable_int(sds_ring); + if (netif_running(adapter->netdev)) + netxen_nic_enable_int(sds_ring); } return work_done; -- GitLab From e4135c2da11c337e3759f98727c4819ba2a849fa Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Fri, 17 Jul 2009 15:27:08 +0000 Subject: [PATCH 0117/1342] netxen: fix thermal check and shutdown Check temperature for all PCI functions, that can allow graceful shutdown of all interfaces on the overheated card. Old code was only monitoring temperature for function 0 only. Signed-off-by: Dhananjay Phadke Signed-off-by: David S. Miller --- drivers/net/netxen/netxen_nic_main.c | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-) diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index 370c52f2776..637ac8b89ba 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -1535,10 +1535,12 @@ static int netxen_nic_check_temp(struct netxen_adapter *adapter) printk(KERN_ALERT "%s: Device temperature %d degrees C exceeds" " maximum allowed. Hardware has been shut down.\n", - netxen_nic_driver_name, temp_val); + netdev->name, temp_val); + + netif_device_detach(netdev); + netxen_nic_down(adapter, netdev); + netxen_nic_detach(adapter); - netif_carrier_off(netdev); - netif_stop_queue(netdev); rv = 1; } else if (temp_state == NX_TEMP_WARN) { if (adapter->temp == NX_TEMP_NORMAL) { @@ -1546,13 +1548,13 @@ static int netxen_nic_check_temp(struct netxen_adapter *adapter) "%s: Device temperature %d degrees C " "exceeds operating range." " Immediate action needed.\n", - netxen_nic_driver_name, temp_val); + netdev->name, temp_val); } } else { if (adapter->temp == NX_TEMP_WARN) { printk(KERN_INFO "%s: Device temperature is now %d degrees C" - " in normal range.\n", netxen_nic_driver_name, + " in normal range.\n", netdev->name, temp_val); } } @@ -1625,7 +1627,7 @@ void netxen_watchdog_task(struct work_struct *work) struct netxen_adapter *adapter = container_of(work, struct netxen_adapter, watchdog_task); - if ((adapter->portnum == 0) && netxen_nic_check_temp(adapter)) + if (netxen_nic_check_temp(adapter)) return; if (!adapter->has_link_events) -- GitLab From f249fb783092471a4808e5fc5bda071d2724810d Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?R=C3=A9mi=20Denis-Courmont?= Date: Mon, 20 Jul 2009 00:47:04 +0000 Subject: [PATCH 0118/1342] Fix error return for setsockopt(SO_TIMESTAMPING) MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit I guess it should be -EINVAL rather than EINVAL. I have not checked when the bug came in. Perhaps a candidate for -stable? Signed-off-by: Rémi Denis-Courmont Signed-off-by: David S. Miller --- net/core/sock.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/core/sock.c b/net/core/sock.c index d9eec153d53..bbb25be7ddf 100644 --- a/net/core/sock.c +++ b/net/core/sock.c @@ -631,7 +631,7 @@ set_rcvbuf: case SO_TIMESTAMPING: if (val & ~SOF_TIMESTAMPING_MASK) { - ret = EINVAL; + ret = -EINVAL; break; } sock_valbool_flag(sk, SOCK_TIMESTAMPING_TX_HARDWARE, -- GitLab From e445bb4ed677f8df0d4f8c1abc15c668bd182f28 Mon Sep 17 00:00:00 2001 From: Ken Kawasaki Date: Sun, 19 Jul 2009 13:08:12 +0000 Subject: [PATCH 0119/1342] 3c589_cs: re-initialize the multicast in the tc589_reset 3c589_cs: re-initialize the multicast in the tc589_reset, and spin_lock the set_multicast_list function. Signed-off-by: Ken Kawasaki Signed-off-by: David S. Miller --- drivers/net/pcmcia/3c589_cs.c | 21 ++++++++++++++------- 1 file changed, 14 insertions(+), 7 deletions(-) diff --git a/drivers/net/pcmcia/3c589_cs.c b/drivers/net/pcmcia/3c589_cs.c index ec7cf5ac4f0..690b9c76d34 100644 --- a/drivers/net/pcmcia/3c589_cs.c +++ b/drivers/net/pcmcia/3c589_cs.c @@ -156,6 +156,7 @@ static struct net_device_stats *el3_get_stats(struct net_device *dev); static int el3_rx(struct net_device *dev); static int el3_close(struct net_device *dev); static void el3_tx_timeout(struct net_device *dev); +static void set_rx_mode(struct net_device *dev); static void set_multicast_list(struct net_device *dev); static const struct ethtool_ops netdev_ethtool_ops; @@ -488,8 +489,7 @@ static void tc589_reset(struct net_device *dev) /* Switch to register set 1 for normal use. */ EL3WINDOW(1); - /* Accept b-cast and phys addr only. */ - outw(SetRxFilter | RxStation | RxBroadcast, ioaddr + EL3_CMD); + set_rx_mode(dev); outw(StatsEnable, ioaddr + EL3_CMD); /* Turn on statistics. */ outw(RxEnable, ioaddr + EL3_CMD); /* Enable the receiver. */ outw(TxEnable, ioaddr + EL3_CMD); /* Enable transmitter. */ @@ -700,7 +700,7 @@ static irqreturn_t el3_interrupt(int irq, void *dev_id) if (fifo_diag & 0x2000) { /* Rx underrun */ tc589_wait_for_completion(dev, RxReset); - set_multicast_list(dev); + set_rx_mode(dev); outw(RxEnable, ioaddr + EL3_CMD); } outw(AckIntr | AdapterFailure, ioaddr + EL3_CMD); @@ -905,14 +905,11 @@ static int el3_rx(struct net_device *dev) return 0; } -static void set_multicast_list(struct net_device *dev) +static void set_rx_mode(struct net_device *dev) { - struct el3_private *lp = netdev_priv(dev); - struct pcmcia_device *link = lp->p_dev; unsigned int ioaddr = dev->base_addr; u16 opts = SetRxFilter | RxStation | RxBroadcast; - if (!pcmcia_dev_present(link)) return; if (dev->flags & IFF_PROMISC) opts |= RxMulticast | RxProm; else if (dev->mc_count || (dev->flags & IFF_ALLMULTI)) @@ -920,6 +917,16 @@ static void set_multicast_list(struct net_device *dev) outw(opts, ioaddr + EL3_CMD); } +static void set_multicast_list(struct net_device *dev) +{ + struct el3_private *priv = netdev_priv(dev); + unsigned long flags; + + spin_lock_irqsave(&priv->lock, flags); + set_rx_mode(dev); + spin_unlock_irqrestore(&priv->lock, flags); +} + static int el3_close(struct net_device *dev) { struct el3_private *lp = netdev_priv(dev); -- GitLab From 90cb665937a2aab16d9aa60f22908195c16dcffd Mon Sep 17 00:00:00 2001 From: Cesar Eduardo Barros Date: Sun, 19 Jul 2009 08:03:32 +0000 Subject: [PATCH 0120/1342] New device ID for sc92031 [1088:2031] MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit rain_maker@root-forum.org wrote: > Hello cesar, > > In a recent thread in a german linux forum, a user reported his PIC > NIC not being recognized by the kernel. > > Fortunately he provided enough information and I was able to help him > and get the device working with the sc92031 driver. > > The device ID is [1088:2031] (Vendor is called "Microcomputer Systems > (M) Son"), here is the respective thread in "ubuntuusers.de" > > http://forum.ubuntuusers.de/topic/lankarte-unter-xubuntu-wird-nicht-erkannt/ > > (Although you might not speak german, the code provided will show > you, that the device is actually working with your driver). > > It would be nice, if you include this new device ID to the > sc92031-driver. > > Regards, > > Axel Köllhofer (aka Rain_Maker) Cc: rain_maker@root-forum.org Signed-off-by: Cesar Eduardo Barros Signed-off-by: David S. Miller --- drivers/net/sc92031.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/net/sc92031.c b/drivers/net/sc92031.c index 18821f217e1..e3156c97bb5 100644 --- a/drivers/net/sc92031.c +++ b/drivers/net/sc92031.c @@ -1593,6 +1593,7 @@ out: static struct pci_device_id sc92031_pci_device_id_table[] __devinitdata = { { PCI_DEVICE(PCI_VENDOR_ID_SILAN, 0x2031) }, { PCI_DEVICE(PCI_VENDOR_ID_SILAN, 0x8139) }, + { PCI_DEVICE(0x1088, 0x2031) }, { 0, } }; MODULE_DEVICE_TABLE(pci, sc92031_pci_device_id_table); -- GitLab From e2372902d84af3443d421a984d812ec87eeb0758 Mon Sep 17 00:00:00 2001 From: Wolfgang Grandegger Date: Mon, 20 Jul 2009 04:06:39 +0000 Subject: [PATCH 0121/1342] can: sja1000: remove duplicated includes Remove duplicated #include('s) in drivers/net/can/sja1000/sja1000.c Signed-off-by: Huang Weiyi Signed-off-by: Wolfgang Grandegger Signed-off-by: David S. Miller --- drivers/net/can/sja1000/sja1000.c | 1 - 1 file changed, 1 deletion(-) diff --git a/drivers/net/can/sja1000/sja1000.c b/drivers/net/can/sja1000/sja1000.c index 571f133a8fe..08ebee79d8a 100644 --- a/drivers/net/can/sja1000/sja1000.c +++ b/drivers/net/can/sja1000/sja1000.c @@ -63,7 +63,6 @@ #include #include #include -#include #include "sja1000.h" -- GitLab From b3d0df7ca35018ebbc24fd102ed7021cf593ba74 Mon Sep 17 00:00:00 2001 From: Wolfgang Grandegger Date: Mon, 20 Jul 2009 04:06:40 +0000 Subject: [PATCH 0122/1342] can: restart device even if dev_alloc_skb() fails If dev_alloc_skb() failed in can_restart(), the device was left behind in the bus-off state. This patch restarts the device nevertheless. Signed-off-by: Kurt Van Dijck Signed-off-by: Wolfgang Grandegger Signed-off-by: David S. Miller --- drivers/net/can/dev.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/can/dev.c b/drivers/net/can/dev.c index 574daddc21b..06083c32869 100644 --- a/drivers/net/can/dev.c +++ b/drivers/net/can/dev.c @@ -346,7 +346,7 @@ void can_restart(unsigned long data) skb = dev_alloc_skb(sizeof(struct can_frame)); if (skb == NULL) { err = -ENOMEM; - goto out; + goto restart; } skb->dev = dev; skb->protocol = htons(ETH_P_CAN); @@ -361,13 +361,13 @@ void can_restart(unsigned long data) stats->rx_packets++; stats->rx_bytes += cf->can_dlc; +restart: dev_dbg(dev->dev.parent, "restarted\n"); priv->can_stats.restarts++; /* Now restart the device */ err = priv->do_set_mode(dev, CAN_MODE_START); -out: netif_carrier_on(dev); if (err) dev_err(dev->dev.parent, "Error %d during restart", err); -- GitLab From 1b0d92244ff2434a98272f6d2525da32fc230f19 Mon Sep 17 00:00:00 2001 From: Wolfgang Grandegger Date: Mon, 20 Jul 2009 04:06:41 +0000 Subject: [PATCH 0123/1342] can: switch carrier on if device was stopped while in bus-off state This patch fixes a problem when a device is stopped while in the bus-off state. Then the carrier remains off forever. Signed-off-by: Kurt Van Dijck Signed-off-by: Wolfgang Grandegger Signed-off-by: David S. Miller --- drivers/net/can/dev.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/net/can/dev.c b/drivers/net/can/dev.c index 06083c32869..9e4283aff82 100644 --- a/drivers/net/can/dev.c +++ b/drivers/net/can/dev.c @@ -473,6 +473,10 @@ int open_candev(struct net_device *dev) return -EINVAL; } + /* Switch carrier on if device was stopped while in bus-off state */ + if (!netif_carrier_ok(dev)) + netif_carrier_on(dev); + setup_timer(&priv->restart_timer, can_restart, (unsigned long)dev); return 0; -- GitLab From cefcb800fa9536bb6f29485c53e6c82a65b0c022 Mon Sep 17 00:00:00 2001 From: Goldwyn Rodrigues Date: Sat, 11 Jul 2009 10:57:27 -0500 Subject: [PATCH 0124/1342] ocfs2: Initialize count in aio_write before generic_write_checks generic_write_checks() expects count to be initialized to the size of the write. Writes to files open with O_DIRECT|O_LARGEFILE write 0 bytes because count is uninitialized. Signed-off-by: Goldwyn Rodrigues Signed-off-by: Joel Becker --- fs/ocfs2/file.c | 1 + 1 file changed, 1 insertion(+) diff --git a/fs/ocfs2/file.c b/fs/ocfs2/file.c index a49fa44aea1..aa501d3f93f 100644 --- a/fs/ocfs2/file.c +++ b/fs/ocfs2/file.c @@ -1851,6 +1851,7 @@ relock: if (ret) goto out_dio; + count = ocount; ret = generic_write_checks(file, ppos, &count, S_ISBLK(inode->i_mode)); if (ret) -- GitLab From 44d8e4e1e9b941065eb7578669fe51eb65c73e63 Mon Sep 17 00:00:00 2001 From: Subrata Modak Date: Tue, 14 Jul 2009 01:19:31 +0530 Subject: [PATCH 0125/1342] ocfs2: Fix compilation warning for fs/ocfs2/xattr.c MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit gcc 4.4.1 generates the following build warning on i386: CC [M] fs/ocfs2/xattr.o fs/ocfs2/xattr.c: In function ‘ocfs2_xattr_block_get’: fs/ocfs2/xattr.c:1055: warning: ‘block_off’ may be used uninitialized in this function The following fix is based on a similar approach by David Howells few days back: http://lkml.org/lkml/2009/7/9/109, Signed-off-by: Subrata Modak, Signed-off-by: Joel Becker --- fs/ocfs2/xattr.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/fs/ocfs2/xattr.c b/fs/ocfs2/xattr.c index ba320e25074..d1a27cda984 100644 --- a/fs/ocfs2/xattr.c +++ b/fs/ocfs2/xattr.c @@ -1052,7 +1052,8 @@ static int ocfs2_xattr_block_get(struct inode *inode, struct ocfs2_xattr_block *xb; struct ocfs2_xattr_value_root *xv; size_t size; - int ret = -ENODATA, name_offset, name_len, block_off, i; + int ret = -ENODATA, name_offset, name_len, i; + int uninitialized_var(block_off); xs->bucket = ocfs2_xattr_bucket_new(inode); if (!xs->bucket) { -- GitLab From cbfa9639aea5007313b75ec43b689d5f9e0c037d Mon Sep 17 00:00:00 2001 From: Wengang Wang Date: Mon, 13 Jul 2009 11:38:23 +0800 Subject: [PATCH 0126/1342] ocfs2: Fix error return in ocfs2_write_cluster() A typo caused ocfs2_write_cluster() to return 0 in some error cases. Fix it. Signed-off-by: Wengang Wang Signed-off-by: Joel Becker --- fs/ocfs2/aops.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/ocfs2/aops.c b/fs/ocfs2/aops.c index b2c52b3a148..25aced3b0c7 100644 --- a/fs/ocfs2/aops.c +++ b/fs/ocfs2/aops.c @@ -1301,7 +1301,7 @@ static int ocfs2_write_cluster(struct address_space *mapping, if (tmpret) { mlog_errno(tmpret); if (ret == 0) - tmpret = ret; + ret = tmpret; } } -- GitLab From 1f4cea3790bf44137192f441ee84af256e3bf809 Mon Sep 17 00:00:00 2001 From: Wengang Wang Date: Mon, 13 Jul 2009 11:38:58 +0800 Subject: [PATCH 0127/1342] ocfs2: Fail ocfs2_get_block() immediately when a block needs allocation ocfs2_get_block() does no allocation. Hole filling for writes should have happened farther up in the call chain. We detect this case and print an error, but we then continue with the function. We should be exiting immediately. Signed-off-by: Wengang Wang Signed-off-by: Joel Becker --- fs/ocfs2/aops.c | 1 + 1 file changed, 1 insertion(+) diff --git a/fs/ocfs2/aops.c b/fs/ocfs2/aops.c index 25aced3b0c7..e511df10145 100644 --- a/fs/ocfs2/aops.c +++ b/fs/ocfs2/aops.c @@ -193,6 +193,7 @@ static int ocfs2_get_block(struct inode *inode, sector_t iblock, (unsigned long long)OCFS2_I(inode)->ip_blkno); mlog(ML_ERROR, "Size %llu, clusters %u\n", (unsigned long long)i_size_read(inode), OCFS2_I(inode)->ip_clusters); dump_stack(); + goto bail; } past_eof = ocfs2_blocks_for_bytes(inode->i_sb, i_size_read(inode)); -- GitLab From 77f32dfdd97857280ae1ebac64382ff082cd7ea0 Mon Sep 17 00:00:00 2001 From: Denis Turischev Date: Mon, 20 Jul 2009 18:48:17 +0300 Subject: [PATCH 0128/1342] x86: Add reboot fixup for SBC-fitPC2 The CompuLab SBC-fitPC2 board needs to reboot via BIOS. Signed-off-by: Denis Turischev Signed-off-by: Mike Rapoport Signed-off-by: H. Peter Anvin --- arch/x86/kernel/reboot.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/x86/kernel/reboot.c b/arch/x86/kernel/reboot.c index d2d1ce8170f..508e982dd07 100644 --- a/arch/x86/kernel/reboot.c +++ b/arch/x86/kernel/reboot.c @@ -249,6 +249,14 @@ static struct dmi_system_id __initdata reboot_dmi_table[] = { DMI_MATCH(DMI_PRODUCT_NAME, "VGN-Z540N"), }, }, + { /* Handle problems with rebooting on CompuLab SBC-FITPC2 */ + .callback = set_bios_reboot, + .ident = "CompuLab SBC-FITPC2", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "CompuLab"), + DMI_MATCH(DMI_PRODUCT_NAME, "SBC-FITPC2"), + }, + }, { } }; -- GitLab From 155b73529583c38f30fd394d692b15a893960782 Mon Sep 17 00:00:00 2001 From: Uros Bizjak Date: Sun, 19 Jul 2009 18:06:35 +0200 Subject: [PATCH 0129/1342] x86: Fix movq immediate operand constraints in uaccess_64.h arch/x86/include/asm/uaccess_64.h uses wrong asm operand constraint ("ir") for movq insn. Since movq sign-extends its immediate operand, "er" constraint should be used instead. Attached patch changes all uses of __put_user_asm in uaccess_64.h to use "er" when "q" insn suffix is involved. Patch was compile tested on x86_64 with defconfig. Signed-off-by: Uros Bizjak Signed-off-by: H. Peter Anvin Cc: stable@kernel.org --- arch/x86/include/asm/uaccess_64.h | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/arch/x86/include/asm/uaccess_64.h b/arch/x86/include/asm/uaccess_64.h index 8cc687326eb..db24b215fc5 100644 --- a/arch/x86/include/asm/uaccess_64.h +++ b/arch/x86/include/asm/uaccess_64.h @@ -88,11 +88,11 @@ int __copy_to_user(void __user *dst, const void *src, unsigned size) ret, "l", "k", "ir", 4); return ret; case 8:__put_user_asm(*(u64 *)src, (u64 __user *)dst, - ret, "q", "", "ir", 8); + ret, "q", "", "er", 8); return ret; case 10: __put_user_asm(*(u64 *)src, (u64 __user *)dst, - ret, "q", "", "ir", 10); + ret, "q", "", "er", 10); if (unlikely(ret)) return ret; asm("":::"memory"); @@ -101,12 +101,12 @@ int __copy_to_user(void __user *dst, const void *src, unsigned size) return ret; case 16: __put_user_asm(*(u64 *)src, (u64 __user *)dst, - ret, "q", "", "ir", 16); + ret, "q", "", "er", 16); if (unlikely(ret)) return ret; asm("":::"memory"); __put_user_asm(1[(u64 *)src], 1 + (u64 __user *)dst, - ret, "q", "", "ir", 8); + ret, "q", "", "er", 8); return ret; default: return copy_user_generic((__force void *)dst, src, size); @@ -157,7 +157,7 @@ int __copy_in_user(void __user *dst, const void __user *src, unsigned size) ret, "q", "", "=r", 8); if (likely(!ret)) __put_user_asm(tmp, (u64 __user *)dst, - ret, "q", "", "ir", 8); + ret, "q", "", "er", 8); return ret; } default: -- GitLab From 032e46cbf5fb1d768d7dec5631c224e22b4be46f Mon Sep 17 00:00:00 2001 From: Jerone Young Date: Mon, 20 Jul 2009 22:14:59 -0700 Subject: [PATCH 0130/1342] Input: atkbd - add force relese key quirk for Soltech TA12 Netbooks based on the Soltech TA12 do not send a key release for volume keys causing Linux to think the key is constantly being pressed forever. Added quirk data for forced release keys. BugLink: https://bugs.launchpad.net//bugs/397499 Signed-off-by: Jerone Young Signed-off-by: Tim Gardner Signed-off-by: Dmitry Torokhov --- drivers/input/keyboard/atkbd.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/drivers/input/keyboard/atkbd.c b/drivers/input/keyboard/atkbd.c index 809a7ddbe3a..95fe0452dae 100644 --- a/drivers/input/keyboard/atkbd.c +++ b/drivers/input/keyboard/atkbd.c @@ -908,6 +908,13 @@ static unsigned int atkbd_amilo_xi3650_forced_release_keys[] = { 0x67, 0xed, 0x90, 0xa2, 0x99, 0xa4, 0xae, 0xb0, -1U }; +/* + * Soltech TA12 system with broken key release on volume keys and mute key + */ +static unsigned int atkdb_soltech_ta12_forced_release_keys[] = { + 0xa0, 0xae, 0xb0, -1U +}; + /* * atkbd_set_keycode_table() initializes keyboard's keycode table * according to the selected scancode set @@ -1592,6 +1599,15 @@ static struct dmi_system_id atkbd_dmi_quirk_table[] __initdata = { .callback = atkbd_setup_forced_release, .driver_data = atkbd_amilo_xi3650_forced_release_keys, }, + { + .ident = "Soltech Corporation TA12", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Soltech Corporation"), + DMI_MATCH(DMI_PRODUCT_NAME, "TA12"), + }, + .callback = atkbd_setup_forced_release, + .driver_data = atkdb_soltech_ta12_forced_release_keys, + }, { } }; -- GitLab From ebe119cd0929df4878f758ebf880cb435e4dcaaf Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Mon, 20 Jul 2009 23:27:39 -0700 Subject: [PATCH 0131/1342] x86: Fix movq immediate operand constraints in uaccess.h The movq instruction, generated by __put_user_asm() when used for 64-bit data, takes a sign-extended immediate ("e") not a zero-extended immediate ("Z"). Signed-off-by: H. Peter Anvin Cc: Uros Bizjak Cc: stable@kernel.org --- arch/x86/include/asm/uaccess.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/x86/include/asm/uaccess.h b/arch/x86/include/asm/uaccess.h index 20e6a795e16..d2c6c930b49 100644 --- a/arch/x86/include/asm/uaccess.h +++ b/arch/x86/include/asm/uaccess.h @@ -212,9 +212,9 @@ extern int __get_user_bad(void); : "A" ((typeof(*(ptr)))(x)), "c" (ptr) : "ebx") #else #define __put_user_asm_u64(x, ptr, retval, errret) \ - __put_user_asm(x, ptr, retval, "q", "", "Zr", errret) + __put_user_asm(x, ptr, retval, "q", "", "er", errret) #define __put_user_asm_ex_u64(x, addr) \ - __put_user_asm_ex(x, addr, "q", "", "Zr") + __put_user_asm_ex(x, addr, "q", "", "er") #define __put_user_x8(x, ptr, __ret_pu) __put_user_x(8, x, ptr, __ret_pu) #endif -- GitLab From f1015c447781729060c415f5133164c638561f25 Mon Sep 17 00:00:00 2001 From: dingdinghua Date: Wed, 15 Jul 2009 21:42:05 +0200 Subject: [PATCH 0132/1342] jbd: fix race between write_metadata_buffer and get_write_access The function journal_write_metadata_buffer() calls jbd_unlock_bh_state(bh_in) too early; this could potentially allow another thread to call get_write_access on the buffer head, modify the data, and dirty it, and allowing the wrong data to be written into the journal. Fortunately, if we lose this race, the only time this will actually cause filesystem corruption is if there is a system crash or other unclean shutdown of the system before the next commit can take place. Signed-off-by: dingdinghua Acked-by: "Theodore Ts'o" Signed-off-by: Jan Kara --- fs/jbd/journal.c | 20 +++++++++++--------- 1 file changed, 11 insertions(+), 9 deletions(-) diff --git a/fs/jbd/journal.c b/fs/jbd/journal.c index 94a64a199a6..f96f85092d1 100644 --- a/fs/jbd/journal.c +++ b/fs/jbd/journal.c @@ -287,6 +287,7 @@ int journal_write_metadata_buffer(transaction_t *transaction, struct page *new_page; unsigned int new_offset; struct buffer_head *bh_in = jh2bh(jh_in); + journal_t *journal = transaction->t_journal; /* * The buffer really shouldn't be locked: only the current committing @@ -300,6 +301,11 @@ int journal_write_metadata_buffer(transaction_t *transaction, J_ASSERT_BH(bh_in, buffer_jbddirty(bh_in)); new_bh = alloc_buffer_head(GFP_NOFS|__GFP_NOFAIL); + /* keep subsequent assertions sane */ + new_bh->b_state = 0; + init_buffer(new_bh, NULL, NULL); + atomic_set(&new_bh->b_count, 1); + new_jh = journal_add_journal_head(new_bh); /* This sleeps */ /* * If a new transaction has already done a buffer copy-out, then @@ -361,14 +367,6 @@ repeat: kunmap_atomic(mapped_data, KM_USER0); } - /* keep subsequent assertions sane */ - new_bh->b_state = 0; - init_buffer(new_bh, NULL, NULL); - atomic_set(&new_bh->b_count, 1); - jbd_unlock_bh_state(bh_in); - - new_jh = journal_add_journal_head(new_bh); /* This sleeps */ - set_bh_page(new_bh, new_page, new_offset); new_jh->b_transaction = NULL; new_bh->b_size = jh2bh(jh_in)->b_size; @@ -385,7 +383,11 @@ repeat: * copying is moved to the transaction's shadow queue. */ JBUFFER_TRACE(jh_in, "file as BJ_Shadow"); - journal_file_buffer(jh_in, transaction, BJ_Shadow); + spin_lock(&journal->j_list_lock); + __journal_file_buffer(jh_in, transaction, BJ_Shadow); + spin_unlock(&journal->j_list_lock); + jbd_unlock_bh_state(bh_in); + JBUFFER_TRACE(new_jh, "file as BJ_IO"); journal_file_buffer(new_jh, transaction, BJ_IO); -- GitLab From 591d2fb02ea80472d846c0b8507007806bdd69cc Mon Sep 17 00:00:00 2001 From: Thomas Gleixner Date: Tue, 21 Jul 2009 11:09:39 +0200 Subject: [PATCH 0133/1342] genirq: Delegate irq affinity setting to the irq thread irq_set_thread_affinity() calls set_cpus_allowed_ptr() which might sleep, but irq_set_thread_affinity() is called with desc->lock held and can be called from hard interrupt context as well. The code has another bug as it does not hold a ref on the task struct as required by set_cpus_allowed_ptr(). Just set the IRQTF_AFFINITY bit in action->thread_flags. The next time the thread runs it migrates itself. Solves all of the above problems nicely. Add kerneldoc to irq_set_thread_affinity() while at it. Signed-off-by: Thomas Gleixner LKML-Reference: --- include/linux/interrupt.h | 2 ++ kernel/irq/internals.h | 3 +-- kernel/irq/manage.c | 50 ++++++++++++++++++++++++++++++++++----- kernel/irq/migration.c | 2 +- 4 files changed, 48 insertions(+), 9 deletions(-) diff --git a/include/linux/interrupt.h b/include/linux/interrupt.h index 2721f07e935..88b056ac562 100644 --- a/include/linux/interrupt.h +++ b/include/linux/interrupt.h @@ -64,11 +64,13 @@ * IRQTF_RUNTHREAD - signals that the interrupt handler thread should run * IRQTF_DIED - handler thread died * IRQTF_WARNED - warning "IRQ_WAKE_THREAD w/o thread_fn" has been printed + * IRQTF_AFFINITY - irq thread is requested to adjust affinity */ enum { IRQTF_RUNTHREAD, IRQTF_DIED, IRQTF_WARNED, + IRQTF_AFFINITY, }; typedef irqreturn_t (*irq_handler_t)(int, void *); diff --git a/kernel/irq/internals.h b/kernel/irq/internals.h index 73468253143..e70ed5592eb 100644 --- a/kernel/irq/internals.h +++ b/kernel/irq/internals.h @@ -42,8 +42,7 @@ static inline void unregister_handler_proc(unsigned int irq, extern int irq_select_affinity_usr(unsigned int irq); -extern void -irq_set_thread_affinity(struct irq_desc *desc, const struct cpumask *cpumask); +extern void irq_set_thread_affinity(struct irq_desc *desc); /* * Debugging printout: diff --git a/kernel/irq/manage.c b/kernel/irq/manage.c index 50da6767290..f0de36f13a4 100644 --- a/kernel/irq/manage.c +++ b/kernel/irq/manage.c @@ -80,14 +80,22 @@ int irq_can_set_affinity(unsigned int irq) return 1; } -void -irq_set_thread_affinity(struct irq_desc *desc, const struct cpumask *cpumask) +/** + * irq_set_thread_affinity - Notify irq threads to adjust affinity + * @desc: irq descriptor which has affitnity changed + * + * We just set IRQTF_AFFINITY and delegate the affinity setting + * to the interrupt thread itself. We can not call + * set_cpus_allowed_ptr() here as we hold desc->lock and this + * code can be called from hard interrupt context. + */ +void irq_set_thread_affinity(struct irq_desc *desc) { struct irqaction *action = desc->action; while (action) { if (action->thread) - set_cpus_allowed_ptr(action->thread, cpumask); + set_bit(IRQTF_AFFINITY, &action->thread_flags); action = action->next; } } @@ -112,7 +120,7 @@ int irq_set_affinity(unsigned int irq, const struct cpumask *cpumask) if (desc->status & IRQ_MOVE_PCNTXT) { if (!desc->chip->set_affinity(irq, cpumask)) { cpumask_copy(desc->affinity, cpumask); - irq_set_thread_affinity(desc, cpumask); + irq_set_thread_affinity(desc); } } else { @@ -122,7 +130,7 @@ int irq_set_affinity(unsigned int irq, const struct cpumask *cpumask) #else if (!desc->chip->set_affinity(irq, cpumask)) { cpumask_copy(desc->affinity, cpumask); - irq_set_thread_affinity(desc, cpumask); + irq_set_thread_affinity(desc); } #endif desc->status |= IRQ_AFFINITY_SET; @@ -176,7 +184,7 @@ int irq_select_affinity_usr(unsigned int irq) spin_lock_irqsave(&desc->lock, flags); ret = setup_affinity(irq, desc); if (!ret) - irq_set_thread_affinity(desc, desc->affinity); + irq_set_thread_affinity(desc); spin_unlock_irqrestore(&desc->lock, flags); return ret; @@ -443,6 +451,34 @@ static int irq_wait_for_interrupt(struct irqaction *action) return -1; } +/* + * Check whether we need to change the affinity of the interrupt thread. + */ +static void +irq_thread_check_affinity(struct irq_desc *desc, struct irqaction *action) +{ + cpumask_var_t mask; + + if (!test_and_clear_bit(IRQTF_AFFINITY, &action->thread_flags)) + return; + + /* + * In case we are out of memory we set IRQTF_AFFINITY again and + * try again next time + */ + if (!alloc_cpumask_var(&mask, GFP_KERNEL)) { + set_bit(IRQTF_AFFINITY, &action->thread_flags); + return; + } + + spin_lock_irq(&desc->lock); + cpumask_copy(mask, desc->affinity); + spin_unlock_irq(&desc->lock); + + set_cpus_allowed_ptr(current, mask); + free_cpumask_var(mask); +} + /* * Interrupt handler thread */ @@ -458,6 +494,8 @@ static int irq_thread(void *data) while (!irq_wait_for_interrupt(action)) { + irq_thread_check_affinity(desc, action); + atomic_inc(&desc->threads_active); spin_lock_irq(&desc->lock); diff --git a/kernel/irq/migration.c b/kernel/irq/migration.c index cfe767ca154..fcb6c96f262 100644 --- a/kernel/irq/migration.c +++ b/kernel/irq/migration.c @@ -45,7 +45,7 @@ void move_masked_irq(int irq) < nr_cpu_ids)) if (!desc->chip->set_affinity(irq, desc->pending_mask)) { cpumask_copy(desc->affinity, desc->pending_mask); - irq_set_thread_affinity(desc, desc->pending_mask); + irq_set_thread_affinity(desc); } cpumask_clear(desc->pending_mask); -- GitLab From 513a2396d8e8327aff1ce50bea3fb4f16ff3455b Mon Sep 17 00:00:00 2001 From: Zhu Yi Date: Thu, 9 Jul 2009 17:24:15 +0800 Subject: [PATCH 0134/1342] iwmc3200wifi: fix NULL pointer dereference in iwm_if_free The driver private data is now based on wiphy. So we should not touch the private data after wiphy_free() is called. The patch fixes the potential NULL pointer dereference by making the iwm_wdev_free() the last one on the interface removal path. Signed-off-by: Zhu Yi Signed-off-by: John W. Linville --- drivers/net/wireless/iwmc3200wifi/netdev.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/wireless/iwmc3200wifi/netdev.c b/drivers/net/wireless/iwmc3200wifi/netdev.c index aaa20c6885c..aea5ccf24cc 100644 --- a/drivers/net/wireless/iwmc3200wifi/netdev.c +++ b/drivers/net/wireless/iwmc3200wifi/netdev.c @@ -151,8 +151,8 @@ void iwm_if_free(struct iwm_priv *iwm) return; free_netdev(iwm_to_ndev(iwm)); - iwm_wdev_free(iwm); iwm_priv_deinit(iwm); + iwm_wdev_free(iwm); } int iwm_if_add(struct iwm_priv *iwm) -- GitLab From 872ed1902f511a8947021c562f5728a5bf0640b5 Mon Sep 17 00:00:00 2001 From: Reinette Chatre Date: Thu, 9 Jul 2009 10:33:37 -0700 Subject: [PATCH 0135/1342] iwlwifi: only show active power level via sysfs This changes the power_level file to adhere to the "one value per file" sysfs rule. The user will know which power level was requested as it will be the number just written to this file. It is thus not necessary to create a new sysfs file for this value. In addition it fixes a problem where powertop's parsing expects this value to be the first value in this file without any descriptions. Signed-off-by: Reinette Chatre cc: stable@kernel.org Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-agn.c | 4 +--- drivers/net/wireless/iwlwifi/iwl3945-base.c | 4 +--- 2 files changed, 2 insertions(+), 6 deletions(-) diff --git a/drivers/net/wireless/iwlwifi/iwl-agn.c b/drivers/net/wireless/iwlwifi/iwl-agn.c index 6d1519e1f01..355f50ea7fe 100644 --- a/drivers/net/wireless/iwlwifi/iwl-agn.c +++ b/drivers/net/wireless/iwlwifi/iwl-agn.c @@ -2675,12 +2675,10 @@ static ssize_t show_power_level(struct device *d, struct device_attribute *attr, char *buf) { struct iwl_priv *priv = dev_get_drvdata(d); - int mode = priv->power_data.user_power_setting; int level = priv->power_data.power_mode; char *p = buf; - p += sprintf(p, "INDEX:%d\t", level); - p += sprintf(p, "USER:%d\n", mode); + p += sprintf(p, "%d\n", level); return p - buf + 1; } diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c index cb9bd4c8f25..956798f2c80 100644 --- a/drivers/net/wireless/iwlwifi/iwl3945-base.c +++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c @@ -3643,12 +3643,10 @@ static ssize_t show_power_level(struct device *d, struct device_attribute *attr, char *buf) { struct iwl_priv *priv = dev_get_drvdata(d); - int mode = priv->power_data.user_power_setting; int level = priv->power_data.power_mode; char *p = buf; - p += sprintf(p, "INDEX:%d\t", level); - p += sprintf(p, "USER:%d\n", mode); + p += sprintf(p, "%d\n", level); return p - buf + 1; } -- GitLab From 7b80ece41aea0b73283c6df5a8f25d40aa13135d Mon Sep 17 00:00:00 2001 From: Reinette Chatre Date: Thu, 9 Jul 2009 10:33:39 -0700 Subject: [PATCH 0136/1342] iwlwifi: only update byte count table during aggregation The byte count table is only used for aggregation. Updating it in other cases caused fragmented frames to be dropped. This fixes http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=2004 Signed-off-by: Reinette Chatre Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-tx.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/net/wireless/iwlwifi/iwl-tx.c b/drivers/net/wireless/iwlwifi/iwl-tx.c index 85ae7a62109..9bbeec9427f 100644 --- a/drivers/net/wireless/iwlwifi/iwl-tx.c +++ b/drivers/net/wireless/iwlwifi/iwl-tx.c @@ -872,7 +872,8 @@ int iwl_tx_skb(struct iwl_priv *priv, struct sk_buff *skb) iwl_print_hex_dump(priv, IWL_DL_TX, (u8 *)tx_cmd->hdr, hdr_len); /* Set up entry for this TFD in Tx byte-count array */ - priv->cfg->ops->lib->txq_update_byte_cnt_tbl(priv, txq, + if (info->flags & IEEE80211_TX_CTL_AMPDU) + priv->cfg->ops->lib->txq_update_byte_cnt_tbl(priv, txq, le16_to_cpu(tx_cmd->len)); pci_dma_sync_single_for_device(priv->pci_dev, txcmd_phys, -- GitLab From e2e414d92397c366396d13f627a98a20be92e509 Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Fri, 10 Jul 2009 11:38:14 +0200 Subject: [PATCH 0137/1342] mac80211: disable mesh My kvm instance was complaining a lot about sleeping in atomic contexts in the mesh code, and it turns out that both mesh_path_add() and mpp_path_add() need to be able to sleep (they even use synchronize_rcu()!). I put in a might_sleep() to annotate that, but I see no way, at least right now, of actually making sure those functions are only called from process context since they are both called during TX and RX and the mesh code itself even calls them with rcu_read_lock() "held". Therefore, let's disable it completely for now. It's possible that I'm only seeing this because the hwsim's beaconing is broken and thus the peers aren't discovered right away, but it is possible that this happens even if beaconing is working, for a peer that doesn't exist or so. It should be possible to solve this by deferring the freeing of the tables to call_rcu() instead of using synchronize_rcu(), and also using atomic allocations, but maybe it makes more sense to rework the code to not call these from atomic contexts and defer more of the work to the workqueue. Right now, I can't work on either of those solutions though. Signed-off-by: Johannes Berg Signed-off-by: John W. Linville --- net/mac80211/Kconfig | 1 + net/mac80211/mesh_pathtbl.c | 3 +++ 2 files changed, 4 insertions(+) diff --git a/net/mac80211/Kconfig b/net/mac80211/Kconfig index ba2643a43c7..7836ee92898 100644 --- a/net/mac80211/Kconfig +++ b/net/mac80211/Kconfig @@ -83,6 +83,7 @@ endmenu config MAC80211_MESH bool "Enable mac80211 mesh networking (pre-802.11s) support" depends on MAC80211 && EXPERIMENTAL + depends on BROKEN ---help--- This options enables support of Draft 802.11s mesh networking. The implementation is based on Draft 1.08 of the Mesh Networking diff --git a/net/mac80211/mesh_pathtbl.c b/net/mac80211/mesh_pathtbl.c index 3c72557df45..02f8709a181 100644 --- a/net/mac80211/mesh_pathtbl.c +++ b/net/mac80211/mesh_pathtbl.c @@ -175,6 +175,8 @@ int mesh_path_add(u8 *dst, struct ieee80211_sub_if_data *sdata) int err = 0; u32 hash_idx; + might_sleep(); + if (memcmp(dst, sdata->dev->dev_addr, ETH_ALEN) == 0) /* never add ourselves as neighbours */ return -ENOTSUPP; @@ -265,6 +267,7 @@ int mpp_path_add(u8 *dst, u8 *mpp, struct ieee80211_sub_if_data *sdata) int err = 0; u32 hash_idx; + might_sleep(); if (memcmp(dst, sdata->dev->dev_addr, ETH_ALEN) == 0) /* never add ourselves as neighbours */ -- GitLab From f54c142725ad2ba33c3ee627873cb6966bf05447 Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Fri, 10 Jul 2009 21:41:39 +0200 Subject: [PATCH 0138/1342] rfkill: allow toggling soft state in sysfs again Apparently there actually _are_ tools that try to set this in sysfs even though it wasn't supposed to be used this way without claiming first. Guess what: now that I've cleaned it all up it doesn't matter and we can simply allow setting the soft-block state in sysfs. Signed-off-by: Johannes Berg Tested-By: Darren Salt Signed-off-by: John W. Linville --- net/rfkill/core.c | 27 +++++++++++++++++++-------- 1 file changed, 19 insertions(+), 8 deletions(-) diff --git a/net/rfkill/core.c b/net/rfkill/core.c index 79693fe2001..6896c0b45b4 100644 --- a/net/rfkill/core.c +++ b/net/rfkill/core.c @@ -648,15 +648,26 @@ static ssize_t rfkill_state_store(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) { - /* - * The intention was that userspace can only take control over - * a given device when/if rfkill-input doesn't control it due - * to user_claim. Since user_claim is currently unsupported, - * we never support changing the state from userspace -- this - * can be implemented again later. - */ + struct rfkill *rfkill = to_rfkill(dev); + unsigned long state; + int err; + + if (!capable(CAP_NET_ADMIN)) + return -EPERM; + + err = strict_strtoul(buf, 0, &state); + if (err) + return err; + + if (state != RFKILL_USER_STATE_SOFT_BLOCKED && + state != RFKILL_USER_STATE_UNBLOCKED) + return -EINVAL; + + mutex_lock(&rfkill_global_mutex); + rfkill_set_block(rfkill, state == RFKILL_USER_STATE_SOFT_BLOCKED); + mutex_unlock(&rfkill_global_mutex); - return -EPERM; + return err ?: count; } static ssize_t rfkill_claim_show(struct device *dev, -- GitLab From 8ef86c7bfac5b44529b73b84bc50d3cf574bfb4b Mon Sep 17 00:00:00 2001 From: Pavel Roskin Date: Fri, 10 Jul 2009 16:42:29 -0400 Subject: [PATCH 0139/1342] mac80211: fix injection in monitor mode The location of the 802.11 header is calculated incorrectly due to a wrong placement of parentheses. Found by kmemcheck. Signed-off-by: Pavel Roskin Signed-off-by: John W. Linville --- net/mac80211/tx.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/mac80211/tx.c b/net/mac80211/tx.c index d238a8939a0..3a8922cd103 100644 --- a/net/mac80211/tx.c +++ b/net/mac80211/tx.c @@ -1455,7 +1455,7 @@ int ieee80211_master_start_xmit(struct sk_buff *skb, struct net_device *dev) monitor_iface = UNKNOWN_ADDRESS; len_rthdr = ieee80211_get_radiotap_len(skb->data); - hdr = (struct ieee80211_hdr *)skb->data + len_rthdr; + hdr = (struct ieee80211_hdr *)(skb->data + len_rthdr); hdrlen = ieee80211_hdrlen(hdr->frame_control); /* check the header is complete in the frame */ -- GitLab From 48ab3578a65c5168ecaaa3b21292b643b7bcc2d5 Mon Sep 17 00:00:00 2001 From: Alan Jenkins Date: Sun, 12 Jul 2009 17:03:13 +0100 Subject: [PATCH 0140/1342] rfkill: fix rfkill_set_states() to set the hw state The point of this function is to set the software and hardware state at the same time. When I tried to use it, I found it was only setting the software state. Signed-off-by: Alan Jenkins Reviewed-by: Johannes Berg Signed-off-by: John W. Linville --- net/rfkill/core.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/net/rfkill/core.c b/net/rfkill/core.c index 6896c0b45b4..2fc4a1724eb 100644 --- a/net/rfkill/core.c +++ b/net/rfkill/core.c @@ -549,6 +549,10 @@ void rfkill_set_states(struct rfkill *rfkill, bool sw, bool hw) swprev = !!(rfkill->state & RFKILL_BLOCK_SW); hwprev = !!(rfkill->state & RFKILL_BLOCK_HW); __rfkill_set_sw_state(rfkill, sw); + if (hw) + rfkill->state |= RFKILL_BLOCK_HW; + else + rfkill->state &= ~RFKILL_BLOCK_HW; spin_unlock_irqrestore(&rfkill->lock, flags); -- GitLab From 5d41635195c06fc3116ef3921fe85a9a3ea5ab20 Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Mon, 13 Jul 2009 13:04:30 +0200 Subject: [PATCH 0141/1342] mac80211_hwsim: fix unregistration If you rmmod the module while associated, frames might be transmitted during unregistration -- which will crash if the hwsim%d interface is unregistered first, so only do that after all the virtual wiphys are gone. Signed-off-by: Johannes Berg Signed-off-by: John W. Linville --- drivers/net/wireless/mac80211_hwsim.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/wireless/mac80211_hwsim.c b/drivers/net/wireless/mac80211_hwsim.c index a111bda392e..5bed8241f3c 100644 --- a/drivers/net/wireless/mac80211_hwsim.c +++ b/drivers/net/wireless/mac80211_hwsim.c @@ -1167,8 +1167,8 @@ static void __exit exit_mac80211_hwsim(void) { printk(KERN_DEBUG "mac80211_hwsim: unregister radios\n"); - unregister_netdev(hwsim_mon); mac80211_hwsim_free(); + unregister_netdev(hwsim_mon); } -- GitLab From e603d9d824ff0eda98a65708a7e82112becf2dca Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Mon, 13 Jul 2009 13:25:58 +0200 Subject: [PATCH 0142/1342] mac80211_hwsim: fix use after free Once the "data" pointer is freed, we can't be iterating to the next item in the list any more so we need to use list_for_each_entry_safe with a temporary variable. Signed-off-by: Johannes Berg Signed-off-by: John W. Linville --- drivers/net/wireless/mac80211_hwsim.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/wireless/mac80211_hwsim.c b/drivers/net/wireless/mac80211_hwsim.c index 5bed8241f3c..7916ca3f84c 100644 --- a/drivers/net/wireless/mac80211_hwsim.c +++ b/drivers/net/wireless/mac80211_hwsim.c @@ -709,7 +709,7 @@ static const struct ieee80211_ops mac80211_hwsim_ops = static void mac80211_hwsim_free(void) { struct list_head tmplist, *i, *tmp; - struct mac80211_hwsim_data *data; + struct mac80211_hwsim_data *data, *tmpdata; INIT_LIST_HEAD(&tmplist); @@ -718,7 +718,7 @@ static void mac80211_hwsim_free(void) list_move(i, &tmplist); spin_unlock_bh(&hwsim_radio_lock); - list_for_each_entry(data, &tmplist, list) { + list_for_each_entry_safe(data, tmpdata, &tmplist, list) { debugfs_remove(data->debugfs_group); debugfs_remove(data->debugfs_ps); debugfs_remove(data->debugfs); -- GitLab From 35946a571099a50d2595c8866f07617d29558f53 Mon Sep 17 00:00:00 2001 From: Javier Cardona Date: Mon, 13 Jul 2009 17:00:10 -0700 Subject: [PATCH 0143/1342] mac80211: use correct address for mesh Path Error For forwarded frames, we save the precursor address in addr1 in case it needs to be used to send a Path Error. mesh_path_discard_frame, however, was using addr2 instead of addr1 to send Path Error frames, so correct that and also make the comment regarding this more clear. Signed-off-by: Andrey Yurovsky Signed-off-by: John W. Linville --- net/mac80211/mesh_pathtbl.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) diff --git a/net/mac80211/mesh_pathtbl.c b/net/mac80211/mesh_pathtbl.c index 02f8709a181..479597e8858 100644 --- a/net/mac80211/mesh_pathtbl.c +++ b/net/mac80211/mesh_pathtbl.c @@ -494,8 +494,10 @@ void mesh_path_tx_pending(struct mesh_path *mpath) * @skb: frame to discard * @sdata: network subif the frame was to be sent through * - * If the frame was beign forwarded from another MP, a PERR frame will be sent - * to the precursor. + * If the frame was being forwarded from another MP, a PERR frame will be sent + * to the precursor. The precursor's address (i.e. the previous hop) was saved + * in addr1 of the frame-to-be-forwarded, and would only be overwritten once + * the destination is successfully resolved. * * Locking: the function must me called within a rcu_read_lock region */ @@ -510,7 +512,7 @@ void mesh_path_discard_frame(struct sk_buff *skb, u8 *ra, *da; da = hdr->addr3; - ra = hdr->addr2; + ra = hdr->addr1; mpath = mesh_path_lookup(da, sdata); if (mpath) dsn = ++mpath->dsn; -- GitLab From 65b5a69860ed3bc4224368b804d381cd9cafa90a Mon Sep 17 00:00:00 2001 From: Bob Copeland Date: Mon, 13 Jul 2009 21:57:39 -0400 Subject: [PATCH 0144/1342] ath5k: temporarily disable crypto for AP mode Pavel Roskin reported some issues with using AP mode without nohwcrypt=1. Most likely this is similar to the problem fixed some time ago in ath9k by 3f53dd64f192450cb331c0fecfc26ca952fb242f, "ath9k: Fix hw crypto configuration for TKIP in AP mode." That only affects TKIP but it's easiest to just disable that and WEP too until we get a proper fix in. Signed-off-by: Bob Copeland Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath5k/base.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/net/wireless/ath/ath5k/base.c b/drivers/net/wireless/ath/ath5k/base.c index ea045151f95..029c1bc7468 100644 --- a/drivers/net/wireless/ath/ath5k/base.c +++ b/drivers/net/wireless/ath/ath5k/base.c @@ -2970,6 +2970,9 @@ ath5k_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd, if (modparam_nohwcrypt) return -EOPNOTSUPP; + if (sc->opmode == NL80211_IFTYPE_AP) + return -EOPNOTSUPP; + switch (key->alg) { case ALG_WEP: case ALG_TKIP: -- GitLab From 3da7429ce92abd79b14e2275a28be144ce2c3013 Mon Sep 17 00:00:00 2001 From: Larry Finger Date: Tue, 14 Jul 2009 15:55:16 -0500 Subject: [PATCH 0145/1342] rtl8187: Fix for kernel oops when unloading with LEDs enabled MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit When rtl8187 is unloaded and CONFIG_RTL8187_LEDS is set, the kernel may oops when the module is unloaded as the workqueue for led_on was not being cancelled. This patch fixes the problem reported in http://marc.info/?l=linux-wireless&m=124742957615781&w=2. Reported-by: Gábor Stefanik Signed-off-by: Larry Finger Signed-off-by: John W. Linville --- drivers/net/wireless/rtl818x/rtl8187_leds.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/net/wireless/rtl818x/rtl8187_leds.c b/drivers/net/wireless/rtl818x/rtl8187_leds.c index b4425359224..cf9f899fe0e 100644 --- a/drivers/net/wireless/rtl818x/rtl8187_leds.c +++ b/drivers/net/wireless/rtl818x/rtl8187_leds.c @@ -208,11 +208,12 @@ void rtl8187_leds_exit(struct ieee80211_hw *dev) { struct rtl8187_priv *priv = dev->priv; - rtl8187_unregister_led(&priv->led_tx); /* turn the LED off before exiting */ queue_delayed_work(dev->workqueue, &priv->led_off, 0); cancel_delayed_work_sync(&priv->led_off); + cancel_delayed_work_sync(&priv->led_on); rtl8187_unregister_led(&priv->led_rx); + rtl8187_unregister_led(&priv->led_tx); } #endif /* def CONFIG_RTL8187_LED */ -- GitLab From 6c95e2a2f0f0bf4c8880d5b74b2f7f359d352d03 Mon Sep 17 00:00:00 2001 From: Niko Jokinen Date: Wed, 15 Jul 2009 11:00:53 +0300 Subject: [PATCH 0146/1342] nl80211: Memory leak fixed Potential memory leak via msg pointer in nl80211_get_key() function. Signed-off-by: Niko Jokinen Signed-off-by: Luciano Coelho Signed-off-by: John W. Linville --- net/wireless/nl80211.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c index 43bdb1372ca..634496b3ed7 100644 --- a/net/wireless/nl80211.c +++ b/net/wireless/nl80211.c @@ -997,7 +997,7 @@ static int nl80211_get_key(struct sk_buff *skb, struct genl_info *info) if (IS_ERR(hdr)) { err = PTR_ERR(hdr); - goto out; + goto free_msg; } cookie.msg = msg; @@ -1011,7 +1011,7 @@ static int nl80211_get_key(struct sk_buff *skb, struct genl_info *info) &cookie, get_key_callback); if (err) - goto out; + goto free_msg; if (cookie.error) goto nla_put_failure; @@ -1022,6 +1022,7 @@ static int nl80211_get_key(struct sk_buff *skb, struct genl_info *info) nla_put_failure: err = -ENOBUFS; + free_msg: nlmsg_free(msg); out: cfg80211_put_dev(drv); -- GitLab From 7adfd5c71693b81e995283805b17aa4a2ee0ecd9 Mon Sep 17 00:00:00 2001 From: Andy Whitcroft Date: Thu, 16 Jul 2009 16:28:11 +0100 Subject: [PATCH 0147/1342] rt2x00: Fix chipset detection for rt2500usb The commit below changed the semantics of rt2x00_check_rev so that it no longer checked the bottom 4 bits of the rev were non-zero. During that conversion this part of the check was not propogated to the rt2500usb initialisation. commit 358623c22c9fd837b3b1b444377037f72553dc9f Author: Ivo van Doorn Date: Tue May 5 19:46:08 2009 +0200 rt2x00: Simplify rt2x00_check_rev Without this check rt73 devices are miss recognised as rt2500 devices and two drivers are loaded. Preventing the device being used. Reinstate this check. Signed-off-by: Andy Whitcroft Signed-off-by: John W. Linville --- drivers/net/wireless/rt2x00/rt2500usb.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/net/wireless/rt2x00/rt2500usb.c b/drivers/net/wireless/rt2x00/rt2500usb.c index 66daf68ff0e..ce75426764a 100644 --- a/drivers/net/wireless/rt2x00/rt2500usb.c +++ b/drivers/net/wireless/rt2x00/rt2500usb.c @@ -1550,7 +1550,9 @@ static int rt2500usb_init_eeprom(struct rt2x00_dev *rt2x00dev) rt2500usb_register_read(rt2x00dev, MAC_CSR0, ®); rt2x00_set_chip(rt2x00dev, RT2570, value, reg); - if (!rt2x00_check_rev(&rt2x00dev->chip, 0x000ffff0, 0)) { + if (!rt2x00_check_rev(&rt2x00dev->chip, 0x000ffff0, 0) || + rt2x00_check_rev(&rt2x00dev->chip, 0x0000000f, 0)) { + ERROR(rt2x00dev, "Invalid RT chipset detected.\n"); return -ENODEV; } -- GitLab From c66284f2a421f6aebbafd56cb8b90b8e6a9cb2de Mon Sep 17 00:00:00 2001 From: "Luis R. Rodriguez" Date: Thu, 16 Jul 2009 10:17:35 -0700 Subject: [PATCH 0148/1342] ath9k: Tune ANI function processing on AP mode during ANI reset For AP mode we must tune ANI specially for 2 GHz and for 5 GHz. We mask in only the flags we want to toggle on ath9k_hw_ani_control() through the ah->ani_function bitmask, this will take care of ignoring changes during ANI reset which we were disabling before. Testedy-by: Steven Luo Cc: Bennyam Malavazi Cc: Jouni Malinen Signed-off-by: Luis R. Rodriguez Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/ani.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/drivers/net/wireless/ath/ath9k/ani.c b/drivers/net/wireless/ath/ath9k/ani.c index 1aeafb511dd..aad259b4c19 100644 --- a/drivers/net/wireless/ath/ath9k/ani.c +++ b/drivers/net/wireless/ath/ath9k/ani.c @@ -478,6 +478,18 @@ void ath9k_ani_reset(struct ath_hw *ah) "Reset ANI state opmode %u\n", ah->opmode); ah->stats.ast_ani_reset++; + if (ah->opmode == NL80211_IFTYPE_AP) { + /* + * ath9k_hw_ani_control() will only process items set on + * ah->ani_function + */ + if (IS_CHAN_2GHZ(chan)) + ah->ani_function = (ATH9K_ANI_SPUR_IMMUNITY_LEVEL | + ATH9K_ANI_FIRSTEP_LEVEL); + else + ah->ani_function = 0; + } + ath9k_hw_ani_control(ah, ATH9K_ANI_NOISE_IMMUNITY_LEVEL, 0); ath9k_hw_ani_control(ah, ATH9K_ANI_SPUR_IMMUNITY_LEVEL, 0); ath9k_hw_ani_control(ah, ATH9K_ANI_FIRSTEP_LEVEL, 0); -- GitLab From e56f0975360369347725c49654ecfe3792710429 Mon Sep 17 00:00:00 2001 From: Alan Jenkins Date: Sat, 18 Jul 2009 19:20:20 +0100 Subject: [PATCH 0149/1342] rfkill: remove too-strict __must_check Some drivers don't need the return value of rfkill_set_hw_state(), so it should not be marked as __must_check. Signed-off-by: Alan Jenkins Acked-by: Johannes Berg Signed-off-by: John W. Linville --- include/linux/rfkill.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/linux/rfkill.h b/include/linux/rfkill.h index 2ce29831feb..278777fa8a3 100644 --- a/include/linux/rfkill.h +++ b/include/linux/rfkill.h @@ -224,7 +224,7 @@ void rfkill_destroy(struct rfkill *rfkill); * should be blocked) so that drivers need not keep track of the soft * block state -- which they might not be able to. */ -bool __must_check rfkill_set_hw_state(struct rfkill *rfkill, bool blocked); +bool rfkill_set_hw_state(struct rfkill *rfkill, bool blocked); /** * rfkill_set_sw_state - Set the internal rfkill software block state -- GitLab From 9e81eccf199d910e5ea8db377a43478e4eccd033 Mon Sep 17 00:00:00 2001 From: Christian Lamparter Date: Sun, 19 Jul 2009 05:05:37 +0200 Subject: [PATCH 0150/1342] cfg80211: double free in __cfg80211_scan_done This patch fixes a double free corruption in __cfg80211_scan_done: ================================================ BUG kmalloc-512: Object already free ------------------------------------------------ INFO: Allocated in load_elf_binary+0x18b/0x19af age=6 INFO: Freed in load_elf_binary+0x104e/0x19af age=5 INFO: Slab 0xffffea0001bae4c0 objects=14 used=7 INFO: Object 0xffff88007e8a9918 @offset=6424 fp=0xffff88007e8a9488 Bytes b4 0xffff88007e8a9908: 00 00 00 00 00 00 00 00 5a 5a [...] Pid: 28705, comm: rmmod Tainted: P C 2.6.31-rc2-wl #1 Call Trace: [] print_trailer+0x14e/0x16e [] object_err+0x42/0x61 [] __slab_free+0x2af/0x396 [] ? wiphy_unregister+0x92/0x142 [cfg80211] [] kfree+0x13c/0x17a [] ? wiphy_unregister+0x92/0x142 [cfg80211] [] wiphy_unregister+0x92/0x142 [cfg80211] [] ieee80211_unregister_hw+0xc8/0xff [mac80211] [] p54_unregister_common+0x31/0x66 [p54common] [...] FIX kmalloc-512: Object at 0xffff88007e8a9918 not freed The code path which leads to the *funny* double free: request = rdev->scan_req; dev = dev_get_by_index(&init_net, request->ifidx); /* * the driver was unloaded recently and * therefore dev_get_by_index will return NULL! */ if (!dev) goto out; [...] rdev->scan_req = NULL; /* not executed... */ [...] out: kfree(request); Signed-off-by: Christian Lamparter Signed-off-by: John W. Linville --- net/wireless/scan.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/net/wireless/scan.c b/net/wireless/scan.c index f8e71b30000..9271118e1fc 100644 --- a/net/wireless/scan.c +++ b/net/wireless/scan.c @@ -35,8 +35,6 @@ void cfg80211_scan_done(struct cfg80211_scan_request *request, bool aborted) else nl80211_send_scan_done(wiphy_to_dev(request->wiphy), dev); - wiphy_to_dev(request->wiphy)->scan_req = NULL; - #ifdef CONFIG_WIRELESS_EXT if (!aborted) { memset(&wrqu, 0, sizeof(wrqu)); @@ -48,6 +46,7 @@ void cfg80211_scan_done(struct cfg80211_scan_request *request, bool aborted) dev_put(dev); out: + wiphy_to_dev(request->wiphy)->scan_req = NULL; kfree(request); } EXPORT_SYMBOL(cfg80211_scan_done); -- GitLab From e9084ec98bb9aa3abc6cf73181177780ce7546f8 Mon Sep 17 00:00:00 2001 From: Jan Beulich Date: Thu, 16 Jul 2009 09:45:11 +0100 Subject: [PATCH 0151/1342] x86, mce: Fix set_trigger() accessor Fix the condition checking the result of strchr() (which previously could result in an oops), and make the function return the number of bytes actively used. [ Impact: fix oops ] Signed-off-by: Jan Beulich Cc: Andi Kleen LKML-Reference: <4A5F04B7020000780000AB59@vpn.id2.novell.com> Signed-off-by: H. Peter Anvin --- arch/x86/kernel/cpu/mcheck/mce.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) diff --git a/arch/x86/kernel/cpu/mcheck/mce.c b/arch/x86/kernel/cpu/mcheck/mce.c index 484c1e5f658..1cfb623ce11 100644 --- a/arch/x86/kernel/cpu/mcheck/mce.c +++ b/arch/x86/kernel/cpu/mcheck/mce.c @@ -1692,17 +1692,15 @@ static ssize_t set_trigger(struct sys_device *s, struct sysdev_attribute *attr, const char *buf, size_t siz) { char *p; - int len; strncpy(mce_helper, buf, sizeof(mce_helper)); mce_helper[sizeof(mce_helper)-1] = 0; - len = strlen(mce_helper); p = strchr(mce_helper, '\n'); - if (*p) + if (p) *p = 0; - return len; + return strlen(mce_helper) + !!p; } static ssize_t set_ignore_ce(struct sys_device *s, -- GitLab From 25177476675142d3ebd60849e0cebc46bd1eef8e Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= Date: Sat, 11 Jul 2009 20:52:48 +0000 Subject: [PATCH 0152/1342] macsonic: move probe function to .devinit.text MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit A pointer to mac_sonic_probe is passed to the core via platform_driver_register and so the function must not disappear when the .init sections are discarded. Otherwise (if also having HOTPLUG=y) unbinding and binding a device to the driver via sysfs will result in an oops as does a device being registered late. Various other functions that are called by mac_sonic_probe need to move to .devinit.text, too. An alternative to this patch is using platform_driver_probe instead of platform_driver_register plus removing the pointer to the probe function from the struct platform_driver. Signed-off-by: Uwe Kleine-König Tested-by: Finn Thain Signed-off-by: David S. Miller --- drivers/net/macsonic.c | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) diff --git a/drivers/net/macsonic.c b/drivers/net/macsonic.c index acd143da161..8f492c7b809 100644 --- a/drivers/net/macsonic.c +++ b/drivers/net/macsonic.c @@ -179,7 +179,7 @@ static const struct net_device_ops macsonic_netdev_ops = { .ndo_set_mac_address = eth_mac_addr, }; -static int __init macsonic_init(struct net_device *dev) +static int __devinit macsonic_init(struct net_device *dev) { struct sonic_local* lp = netdev_priv(dev); @@ -223,7 +223,7 @@ static int __init macsonic_init(struct net_device *dev) return 0; } -static int __init mac_onboard_sonic_ethernet_addr(struct net_device *dev) +static int __devinit mac_onboard_sonic_ethernet_addr(struct net_device *dev) { struct sonic_local *lp = netdev_priv(dev); const int prom_addr = ONBOARD_SONIC_PROM_BASE; @@ -288,7 +288,7 @@ static int __init mac_onboard_sonic_ethernet_addr(struct net_device *dev) } else return 0; } -static int __init mac_onboard_sonic_probe(struct net_device *dev) +static int __devinit mac_onboard_sonic_probe(struct net_device *dev) { /* Bwahahaha */ static int once_is_more_than_enough; @@ -409,7 +409,7 @@ static int __init mac_onboard_sonic_probe(struct net_device *dev) return macsonic_init(dev); } -static int __init mac_nubus_sonic_ethernet_addr(struct net_device *dev, +static int __devinit mac_nubus_sonic_ethernet_addr(struct net_device *dev, unsigned long prom_addr, int id) { @@ -424,7 +424,7 @@ static int __init mac_nubus_sonic_ethernet_addr(struct net_device *dev, return 0; } -static int __init macsonic_ident(struct nubus_dev *ndev) +static int __devinit macsonic_ident(struct nubus_dev *ndev) { if (ndev->dr_hw == NUBUS_DRHW_ASANTE_LC && ndev->dr_sw == NUBUS_DRSW_SONIC_LC) @@ -449,7 +449,7 @@ static int __init macsonic_ident(struct nubus_dev *ndev) return -1; } -static int __init mac_nubus_sonic_probe(struct net_device *dev) +static int __devinit mac_nubus_sonic_probe(struct net_device *dev) { static int slots; struct nubus_dev* ndev = NULL; @@ -562,7 +562,7 @@ static int __init mac_nubus_sonic_probe(struct net_device *dev) return macsonic_init(dev); } -static int __init mac_sonic_probe(struct platform_device *pdev) +static int __devinit mac_sonic_probe(struct platform_device *pdev) { struct net_device *dev; struct sonic_local *lp; -- GitLab From 4564cba71637d3b4ea3730f5637b21a9eb3c8999 Mon Sep 17 00:00:00 2001 From: Finn Thain Date: Tue, 21 Jul 2009 12:21:49 -0700 Subject: [PATCH 0153/1342] macsonic, jazzsonic: fix oops on module unload Set the driver data before using it. Fixes an oops when doing rmmod. Signed-off-by: Finn Thain Signed-off-by: David S. Miller --- drivers/net/jazzsonic.c | 1 + drivers/net/macsonic.c | 1 + 2 files changed, 2 insertions(+) diff --git a/drivers/net/jazzsonic.c b/drivers/net/jazzsonic.c index d12106b47bf..2f286091394 100644 --- a/drivers/net/jazzsonic.c +++ b/drivers/net/jazzsonic.c @@ -229,6 +229,7 @@ static int __init jazz_sonic_probe(struct platform_device *pdev) lp = netdev_priv(dev); lp->device = &pdev->dev; SET_NETDEV_DEV(dev, &pdev->dev); + platform_set_drvdata(pdev, dev); netdev_boot_setup_check(dev); diff --git a/drivers/net/macsonic.c b/drivers/net/macsonic.c index 8f492c7b809..61eabcac734 100644 --- a/drivers/net/macsonic.c +++ b/drivers/net/macsonic.c @@ -575,6 +575,7 @@ static int __devinit mac_sonic_probe(struct platform_device *pdev) lp = netdev_priv(dev); lp->device = &pdev->dev; SET_NETDEV_DEV(dev, &pdev->dev); + platform_set_drvdata(pdev, dev); /* This will catch fatal stuff like -ENOMEM as well as success */ err = mac_onboard_sonic_probe(dev); -- GitLab From 5549f7cdf84c02939fd368d0842aa2f472bb6e98 Mon Sep 17 00:00:00 2001 From: Eric Paris Date: Tue, 7 Jul 2009 10:28:23 -0400 Subject: [PATCH 0154/1342] inotify: drop user watch count when a watch is removed The inotify rewrite forgot to drop the inotify watch use cound when a watch was removed. This means that a single inotify fd can only ever register a maximum of /proc/sys/fs/max_user_watches even if some of those had been freed. Signed-off-by: Eric Paris --- fs/notify/inotify/inotify_user.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/fs/notify/inotify/inotify_user.c b/fs/notify/inotify/inotify_user.c index ff27a296584..1a870f9157b 100644 --- a/fs/notify/inotify/inotify_user.c +++ b/fs/notify/inotify/inotify_user.c @@ -404,6 +404,8 @@ skip_send_ignore: /* removed from idr, drop that reference */ fsnotify_put_mark(entry); + + atomic_dec(&group->inotify_data.user->inotify_watches); } /* ding dong the mark is dead */ -- GitLab From 75fe2b26394c59c8e16bd7b76f4be5d048103ad1 Mon Sep 17 00:00:00 2001 From: Eric Paris Date: Tue, 7 Jul 2009 10:28:23 -0400 Subject: [PATCH 0155/1342] inotify: do not leak inode marks in inotify_add_watch inotify_add_watch had a couple of problems. The biggest being that if inotify_add_watch was called on the same inode twice (to update or change the event mask) a refence was taken on the original inode mark by fsnotify_find_mark_entry but was not being dropped at the end of the inotify_add_watch call. Thus if inotify_rm_watch was called although the mark was removed from the inode, the refcnt wouldn't hit zero and we would leak memory. Reported-by: Catalin Marinas Signed-off-by: Eric Paris --- fs/notify/inotify/inotify_user.c | 14 ++++++++++---- 1 file changed, 10 insertions(+), 4 deletions(-) diff --git a/fs/notify/inotify/inotify_user.c b/fs/notify/inotify/inotify_user.c index 1a870f9157b..aff4214f16c 100644 --- a/fs/notify/inotify/inotify_user.c +++ b/fs/notify/inotify/inotify_user.c @@ -463,9 +463,6 @@ retry: goto out_err; spin_lock(&group->inotify_data.idr_lock); - /* if entry is added to the idr we keep the reference obtained - * through fsnotify_mark_add. remember to drop this reference - * when entry is removed from idr */ ret = idr_get_new_above(&group->inotify_data.idr, entry, ++group->inotify_data.last_wd, &ientry->wd); @@ -476,8 +473,13 @@ retry: goto out_err; } atomic_inc(&group->inotify_data.user->inotify_watches); + + /* we put the mark on the idr, take a reference */ + fsnotify_get_mark(entry); } + ret = ientry->wd; + spin_lock(&entry->lock); old_mask = entry->mask; @@ -508,7 +510,11 @@ retry: fsnotify_recalc_group_mask(group); } - return ientry->wd; + /* this either matches fsnotify_find_mark_entry, or init_mark_entry + * depending on which path we took... */ + fsnotify_put_mark(entry); + + return ret; out_err: /* see this isn't supposed to happen, just kill the watch */ -- GitLab From 7e790dd5fc937bc8d2400c30a05e32a9e9eef276 Mon Sep 17 00:00:00 2001 From: Eric Paris Date: Tue, 7 Jul 2009 10:28:24 -0400 Subject: [PATCH 0156/1342] inotify: fix error paths in inotify_update_watch inotify_update_watch could leave things in a horrid state on a number of error paths. We could try to remove idr entries that didn't exist, we could send an IN_IGNORED to userspace for watches that don't exist, and a bit of other stupidity. Clean these up by doing the idr addition before we put the mark on the inode since we can clean that up on error and getting off the inode's mark list is hard. Signed-off-by: Eric Paris --- fs/notify/inotify/inotify_user.c | 79 ++++++++++++++++++++------------ 1 file changed, 49 insertions(+), 30 deletions(-) diff --git a/fs/notify/inotify/inotify_user.c b/fs/notify/inotify/inotify_user.c index aff4214f16c..726118a5845 100644 --- a/fs/notify/inotify/inotify_user.c +++ b/fs/notify/inotify/inotify_user.c @@ -365,6 +365,17 @@ static int inotify_find_inode(const char __user *dirname, struct path *path, uns return error; } +static void inotify_remove_from_idr(struct fsnotify_group *group, + struct inotify_inode_mark_entry *ientry) +{ + struct idr *idr; + + spin_lock(&group->inotify_data.idr_lock); + idr = &group->inotify_data.idr; + idr_remove(idr, ientry->wd); + spin_unlock(&group->inotify_data.idr_lock); + ientry->wd = -1; +} /* * Send IN_IGNORED for this wd, remove this wd from the idr, and drop the * internal reference help on the mark because it is in the idr. @@ -375,7 +386,6 @@ void inotify_ignored_and_remove_idr(struct fsnotify_mark_entry *entry, struct inotify_inode_mark_entry *ientry; struct inotify_event_private_data *event_priv; struct fsnotify_event_private_data *fsn_event_priv; - struct idr *idr; ientry = container_of(entry, struct inotify_inode_mark_entry, fsn_entry); @@ -397,10 +407,7 @@ void inotify_ignored_and_remove_idr(struct fsnotify_mark_entry *entry, skip_send_ignore: /* remove this entry from the idr */ - spin_lock(&group->inotify_data.idr_lock); - idr = &group->inotify_data.idr; - idr_remove(idr, ientry->wd); - spin_unlock(&group->inotify_data.idr_lock); + inotify_remove_from_idr(group, ientry); /* removed from idr, drop that reference */ fsnotify_put_mark(entry); @@ -420,6 +427,7 @@ static int inotify_update_watch(struct fsnotify_group *group, struct inode *inod { struct fsnotify_mark_entry *entry = NULL; struct inotify_inode_mark_entry *ientry; + struct inotify_inode_mark_entry *tmp_ientry; int ret = 0; int add = (arg & IN_MASK_ADD); __u32 mask; @@ -430,50 +438,60 @@ static int inotify_update_watch(struct fsnotify_group *group, struct inode *inod if (unlikely(!mask)) return -EINVAL; - ientry = kmem_cache_alloc(inotify_inode_mark_cachep, GFP_KERNEL); - if (unlikely(!ientry)) + tmp_ientry = kmem_cache_alloc(inotify_inode_mark_cachep, GFP_KERNEL); + if (unlikely(!tmp_ientry)) return -ENOMEM; /* we set the mask at the end after attaching it */ - fsnotify_init_mark(&ientry->fsn_entry, inotify_free_mark); - ientry->wd = 0; + fsnotify_init_mark(&tmp_ientry->fsn_entry, inotify_free_mark); + tmp_ientry->wd = -1; find_entry: spin_lock(&inode->i_lock); entry = fsnotify_find_mark_entry(group, inode); spin_unlock(&inode->i_lock); if (entry) { - kmem_cache_free(inotify_inode_mark_cachep, ientry); ientry = container_of(entry, struct inotify_inode_mark_entry, fsn_entry); } else { - if (atomic_read(&group->inotify_data.user->inotify_watches) >= inotify_max_user_watches) { - ret = -ENOSPC; - goto out_err; - } - - ret = fsnotify_add_mark(&ientry->fsn_entry, group, inode); - if (ret == -EEXIST) - goto find_entry; - else if (ret) + ret = -ENOSPC; + if (atomic_read(&group->inotify_data.user->inotify_watches) >= inotify_max_user_watches) goto out_err; - - entry = &ientry->fsn_entry; retry: ret = -ENOMEM; if (unlikely(!idr_pre_get(&group->inotify_data.idr, GFP_KERNEL))) goto out_err; spin_lock(&group->inotify_data.idr_lock); - ret = idr_get_new_above(&group->inotify_data.idr, entry, - ++group->inotify_data.last_wd, - &ientry->wd); + ret = idr_get_new_above(&group->inotify_data.idr, &tmp_ientry->fsn_entry, + group->inotify_data.last_wd, + &tmp_ientry->wd); spin_unlock(&group->inotify_data.idr_lock); if (ret) { if (ret == -EAGAIN) goto retry; goto out_err; } + + ret = fsnotify_add_mark(&tmp_ientry->fsn_entry, group, inode); + if (ret) { + inotify_remove_from_idr(group, tmp_ientry); + if (ret == -EEXIST) + goto find_entry; + goto out_err; + } + + /* tmp_ientry has been added to the inode, so we are all set up. + * now we just need to make sure tmp_ientry doesn't get freed and + * we need to set up entry and ientry so the generic code can + * do its thing. */ + ientry = tmp_ientry; + entry = &ientry->fsn_entry; + tmp_ientry = NULL; + atomic_inc(&group->inotify_data.user->inotify_watches); + /* update the idr hint */ + group->inotify_data.last_wd = ientry->wd; + /* we put the mark on the idr, take a reference */ fsnotify_get_mark(entry); } @@ -514,14 +532,15 @@ retry: * depending on which path we took... */ fsnotify_put_mark(entry); - return ret; - out_err: - /* see this isn't supposed to happen, just kill the watch */ - if (entry) { - fsnotify_destroy_mark_by_entry(entry); - fsnotify_put_mark(entry); + /* could be an error, could be that we found an existing mark */ + if (tmp_ientry) { + /* on the idr but didn't make it on the inode */ + if (tmp_ientry->wd != -1) + inotify_remove_from_idr(group, tmp_ientry); + kmem_cache_free(inotify_inode_mark_cachep, tmp_ientry); } + return ret; } -- GitLab From 520dc2a526fd681337883b6ff1ddcf7c23b1b063 Mon Sep 17 00:00:00 2001 From: Eric Paris Date: Mon, 13 Jul 2009 15:56:54 -0400 Subject: [PATCH 0157/1342] fsnotify: use def_bool in kconfig instead of letting the user choose fsnotify doens't give the user anything. If someone chooses inotify or dnotify it should build fsnotify, if they don't select one it shouldn't be built. This patch changes fsnotify to be a def_bool=n and makes everything else select it. Also fixes the issue people complained about on lwn where gdm hung because they didn't have inotify and they didn't get the inotify build option..... Signed-off-by: Eric Paris --- fs/notify/Kconfig | 12 +----------- fs/notify/dnotify/Kconfig | 2 +- fs/notify/inotify/Kconfig | 2 +- 3 files changed, 3 insertions(+), 13 deletions(-) diff --git a/fs/notify/Kconfig b/fs/notify/Kconfig index 31dac7e3b0f..dffbb0911d0 100644 --- a/fs/notify/Kconfig +++ b/fs/notify/Kconfig @@ -1,15 +1,5 @@ config FSNOTIFY - bool "Filesystem notification backend" - default y - ---help--- - fsnotify is a backend for filesystem notification. fsnotify does - not provide any userspace interface but does provide the basis - needed for other notification schemes such as dnotify, inotify, - and fanotify. - - Say Y here to enable fsnotify suport. - - If unsure, say Y. + def_bool n source "fs/notify/dnotify/Kconfig" source "fs/notify/inotify/Kconfig" diff --git a/fs/notify/dnotify/Kconfig b/fs/notify/dnotify/Kconfig index 904ff8d5405..f9c1ca139d8 100644 --- a/fs/notify/dnotify/Kconfig +++ b/fs/notify/dnotify/Kconfig @@ -1,6 +1,6 @@ config DNOTIFY bool "Dnotify support" - depends on FSNOTIFY + select FSNOTIFY default y help Dnotify is a directory-based per-fd file change notification system diff --git a/fs/notify/inotify/Kconfig b/fs/notify/inotify/Kconfig index 5356884289a..3e56dbffe72 100644 --- a/fs/notify/inotify/Kconfig +++ b/fs/notify/inotify/Kconfig @@ -15,7 +15,7 @@ config INOTIFY config INOTIFY_USER bool "Inotify support for userspace" - depends on FSNOTIFY + select FSNOTIFY default y ---help--- Say Y here to enable inotify support for userspace, including the -- GitLab From 4a148ba988988b9c400ad0f2cbccc155289b954b Mon Sep 17 00:00:00 2001 From: Eric Paris Date: Mon, 13 Jul 2009 15:56:55 -0400 Subject: [PATCH 0158/1342] inotify: check filename before dropping repeat events inotify drops events if the last event on the queue is the same as the current event. But it does 2 things wrong. First it is comparing old->inode with new->inode. But after an event if put on the queue the ->inode is no longer allowed to be used. It's possible between the last event and this new event the inode could be reused and we would falsely match the inode's memory address between two differing events. The second problem is that when a file is removed fsnotify is passed the negative dentry for the removed object rather than the postive dentry from immediately before the removal. This mean the (broken) inotify tail drop code was matching the NULL ->inode of differing events. The fix is to check the file name which is stored with events when doing the tail drop instead of wrongly checking the address of the stored ->inode. Reported-by: Scott James Remnant Signed-off-by: Eric Paris --- fs/notify/notification.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) diff --git a/fs/notify/notification.c b/fs/notify/notification.c index 959b73e756f..69391fe8efb 100644 --- a/fs/notify/notification.c +++ b/fs/notify/notification.c @@ -136,10 +136,15 @@ static bool event_compare(struct fsnotify_event *old, struct fsnotify_event *new { if ((old->mask == new->mask) && (old->to_tell == new->to_tell) && - (old->data_type == new->data_type)) { + (old->data_type == new->data_type) && + (old->name_len == new->name_len)) { switch (old->data_type) { case (FSNOTIFY_EVENT_INODE): - if (old->inode == new->inode) + /* remember, after old was put on the wait_q we aren't + * allowed to look at the inode any more, only thing + * left to check was if the file_name is the same */ + if (old->name_len && + !strcmp(old->file_name, new->file_name)) return true; break; case (FSNOTIFY_EVENT_PATH): -- GitLab From c05594b62125c528d93af3a78229793aae36df7f Mon Sep 17 00:00:00 2001 From: Eric Paris Date: Mon, 13 Jul 2009 15:56:55 -0400 Subject: [PATCH 0159/1342] fsnotify: fix inotify tail drop check with path entries fsnotify drops new events when they are the same as the tail event on the queue to be sent to userspace. The problem is that if the event comes with a path we forget to break out of the switch statement and fall into the code path which matches on events that do not have any type of file backed information (things like IN_UNMOUNT and IN_Q_OVERFLOW). The problem is that this code thinks all such events should be dropped. Fix is to add a break. Signed-off-by: Eric Paris --- fs/notify/notification.c | 1 + 1 file changed, 1 insertion(+) diff --git a/fs/notify/notification.c b/fs/notify/notification.c index 69391fe8efb..2b20feaf263 100644 --- a/fs/notify/notification.c +++ b/fs/notify/notification.c @@ -151,6 +151,7 @@ static bool event_compare(struct fsnotify_event *old, struct fsnotify_event *new if ((old->path.mnt == new->path.mnt) && (old->path.dentry == new->path.dentry)) return true; + break; case (FSNOTIFY_EVENT_NONE): return true; }; -- GitLab From f44aebcc566d1d6275f7191867b9633dc11de2ee Mon Sep 17 00:00:00 2001 From: Eric Paris Date: Wed, 15 Jul 2009 15:49:52 -0400 Subject: [PATCH 0160/1342] inotify: use GFP_NOFS under potential memory pressure inotify can have a watchs removed under filesystem reclaim. ================================= [ INFO: inconsistent lock state ] 2.6.31-rc2 #16 --------------------------------- inconsistent {IN-RECLAIM_FS-W} -> {RECLAIM_FS-ON-W} usage. khubd/217 [HC0[0]:SC0[0]:HE1:SE1] takes: (iprune_mutex){+.+.?.}, at: [] invalidate_inodes+0x20/0xe3 {IN-RECLAIM_FS-W} state was registered at: [] __lock_acquire+0x2c9/0xac4 [] lock_acquire+0x9f/0xc2 [] __mutex_lock_common+0x2d/0x323 [] mutex_lock_nested+0x2e/0x36 [] shrink_icache_memory+0x38/0x1b2 [] shrink_slab+0xe2/0x13c [] kswapd+0x3d1/0x55d [] kthread+0x66/0x6b [] kernel_thread_helper+0x7/0x10 [] 0xffffffff Two things are needed to fix this. First we need a method to tell fsnotify_create_event() to use GFP_NOFS and second we need to stop using one global IN_IGNORED event and allocate them one at a time. This solves current issues with multiple IN_IGNORED on a queue having tail drop problems and simplifies the allocations since we don't have to worry about two tasks opperating on the IGNORED event concurrently. Signed-off-by: Eric Paris --- fs/notify/fsnotify.c | 4 +++- fs/notify/inotify/inotify_user.c | 18 ++++++++++++------ fs/notify/notification.c | 9 +++++---- include/linux/fsnotify_backend.h | 2 +- 4 files changed, 21 insertions(+), 12 deletions(-) diff --git a/fs/notify/fsnotify.c b/fs/notify/fsnotify.c index ec2f7bd7681..037e878e03f 100644 --- a/fs/notify/fsnotify.c +++ b/fs/notify/fsnotify.c @@ -159,7 +159,9 @@ void fsnotify(struct inode *to_tell, __u32 mask, void *data, int data_is, const if (!group->ops->should_send_event(group, to_tell, mask)) continue; if (!event) { - event = fsnotify_create_event(to_tell, mask, data, data_is, file_name, cookie); + event = fsnotify_create_event(to_tell, mask, data, + data_is, file_name, cookie, + GFP_KERNEL); /* shit, we OOM'd and now we can't tell, maybe * someday someone else will want to do something * here */ diff --git a/fs/notify/inotify/inotify_user.c b/fs/notify/inotify/inotify_user.c index 726118a5845..f30d9bbc2e1 100644 --- a/fs/notify/inotify/inotify_user.c +++ b/fs/notify/inotify/inotify_user.c @@ -57,7 +57,6 @@ int inotify_max_user_watches __read_mostly; static struct kmem_cache *inotify_inode_mark_cachep __read_mostly; struct kmem_cache *event_priv_cachep __read_mostly; -static struct fsnotify_event *inotify_ignored_event; /* * When inotify registers a new group it increments this and uses that @@ -384,12 +383,19 @@ void inotify_ignored_and_remove_idr(struct fsnotify_mark_entry *entry, struct fsnotify_group *group) { struct inotify_inode_mark_entry *ientry; + struct fsnotify_event *ignored_event; struct inotify_event_private_data *event_priv; struct fsnotify_event_private_data *fsn_event_priv; + ignored_event = fsnotify_create_event(NULL, FS_IN_IGNORED, NULL, + FSNOTIFY_EVENT_NONE, NULL, 0, + GFP_NOFS); + if (!ignored_event) + return; + ientry = container_of(entry, struct inotify_inode_mark_entry, fsn_entry); - event_priv = kmem_cache_alloc(event_priv_cachep, GFP_KERNEL); + event_priv = kmem_cache_alloc(event_priv_cachep, GFP_NOFS); if (unlikely(!event_priv)) goto skip_send_ignore; @@ -398,7 +404,7 @@ void inotify_ignored_and_remove_idr(struct fsnotify_mark_entry *entry, fsn_event_priv->group = group; event_priv->wd = ientry->wd; - fsnotify_add_notify_event(group, inotify_ignored_event, fsn_event_priv); + fsnotify_add_notify_event(group, ignored_event, fsn_event_priv); /* did the private data get added? */ if (list_empty(&fsn_event_priv->event_list)) @@ -406,6 +412,9 @@ void inotify_ignored_and_remove_idr(struct fsnotify_mark_entry *entry, skip_send_ignore: + /* matches the reference taken when the event was created */ + fsnotify_put_event(ignored_event); + /* remove this entry from the idr */ inotify_remove_from_idr(group, ientry); @@ -748,9 +757,6 @@ static int __init inotify_user_setup(void) inotify_inode_mark_cachep = KMEM_CACHE(inotify_inode_mark_entry, SLAB_PANIC); event_priv_cachep = KMEM_CACHE(inotify_event_private_data, SLAB_PANIC); - inotify_ignored_event = fsnotify_create_event(NULL, FS_IN_IGNORED, NULL, FSNOTIFY_EVENT_NONE, NULL, 0); - if (!inotify_ignored_event) - panic("unable to allocate the inotify ignored event\n"); inotify_max_queued_events = 16384; inotify_max_user_instances = 128; diff --git a/fs/notify/notification.c b/fs/notify/notification.c index 2b20feaf263..521368574e9 100644 --- a/fs/notify/notification.c +++ b/fs/notify/notification.c @@ -153,7 +153,7 @@ static bool event_compare(struct fsnotify_event *old, struct fsnotify_event *new return true; break; case (FSNOTIFY_EVENT_NONE): - return true; + return false; }; } return false; @@ -345,18 +345,19 @@ static void initialize_event(struct fsnotify_event *event) * @name the filename, if available */ struct fsnotify_event *fsnotify_create_event(struct inode *to_tell, __u32 mask, void *data, - int data_type, const char *name, u32 cookie) + int data_type, const char *name, u32 cookie, + gfp_t gfp) { struct fsnotify_event *event; - event = kmem_cache_alloc(fsnotify_event_cachep, GFP_KERNEL); + event = kmem_cache_alloc(fsnotify_event_cachep, gfp); if (!event) return NULL; initialize_event(event); if (name) { - event->file_name = kstrdup(name, GFP_KERNEL); + event->file_name = kstrdup(name, gfp); if (!event->file_name) { kmem_cache_free(fsnotify_event_cachep, event); return NULL; diff --git a/include/linux/fsnotify_backend.h b/include/linux/fsnotify_backend.h index 6c3de999fb3..4d6f47b5118 100644 --- a/include/linux/fsnotify_backend.h +++ b/include/linux/fsnotify_backend.h @@ -352,7 +352,7 @@ extern void fsnotify_unmount_inodes(struct list_head *list); /* put here because inotify does some weird stuff when destroying watches */ extern struct fsnotify_event *fsnotify_create_event(struct inode *to_tell, __u32 mask, void *data, int data_is, const char *name, - u32 cookie); + u32 cookie, gfp_t gfp); #else -- GitLab From 87cf65601e1709e57f7e28f0f7b3eb0a992c1782 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?R=C3=A9mi=20Denis-Courmont?= Date: Tue, 21 Jul 2009 01:58:35 +0000 Subject: [PATCH 0161/1342] USB host CDC Phonet network interface driver MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Many Nokia handsets support a Phonet interface to the cellular modem via a vendor-specific USB interface. CDC Phonet follows the Communications Device Class model, with one control interface, and and a pair of inactive and active data alternative interface. The later has two bulk endpoint, one per direction. This was tested against Nokia E61, Nokia N95, and the existing Phonet gadget function for the Linux composite USB gadget framework. Signed-off-by: Rémi Denis-Courmont Signed-off-by: David S. Miller --- drivers/net/usb/Kconfig | 8 + drivers/net/usb/Makefile | 1 + drivers/net/usb/cdc-phonet.c | 461 +++++++++++++++++++++++++++++++++++ 3 files changed, 470 insertions(+) create mode 100644 drivers/net/usb/cdc-phonet.c diff --git a/drivers/net/usb/Kconfig b/drivers/net/usb/Kconfig index a906d399813..c47237c2d63 100644 --- a/drivers/net/usb/Kconfig +++ b/drivers/net/usb/Kconfig @@ -369,4 +369,12 @@ config USB_NET_INT51X1 (Powerline Communications) solution with an Intellon INT51x1/INT5200 chip, like the "devolo dLan duo". +config USB_CDC_PHONET + tristate "CDC Phonet support" + depends on PHONET + help + Choose this option to support the Phonet interface to a Nokia + cellular modem, as found on most Nokia handsets with the + "PC suite" USB profile. + endmenu diff --git a/drivers/net/usb/Makefile b/drivers/net/usb/Makefile index b870b0b1cbe..e17afb78f37 100644 --- a/drivers/net/usb/Makefile +++ b/drivers/net/usb/Makefile @@ -21,4 +21,5 @@ obj-$(CONFIG_USB_NET_ZAURUS) += zaurus.o obj-$(CONFIG_USB_NET_MCS7830) += mcs7830.o obj-$(CONFIG_USB_USBNET) += usbnet.o obj-$(CONFIG_USB_NET_INT51X1) += int51x1.o +obj-$(CONFIG_USB_CDC_PHONET) += cdc-phonet.o diff --git a/drivers/net/usb/cdc-phonet.c b/drivers/net/usb/cdc-phonet.c new file mode 100644 index 00000000000..792af72da8a --- /dev/null +++ b/drivers/net/usb/cdc-phonet.c @@ -0,0 +1,461 @@ +/* + * phonet.c -- USB CDC Phonet host driver + * + * Copyright (C) 2008-2009 Nokia Corporation. All rights reserved. + * + * Author: Rémi Denis-Courmont + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + */ + +#include +#include +#include +#include +#include +#include +#include + +#define PN_MEDIA_USB 0x1B + +static const unsigned rxq_size = 17; + +struct usbpn_dev { + struct net_device *dev; + + struct usb_interface *intf, *data_intf; + struct usb_device *usb; + unsigned int tx_pipe, rx_pipe; + u8 active_setting; + u8 disconnected; + + unsigned tx_queue; + spinlock_t tx_lock; + + spinlock_t rx_lock; + struct sk_buff *rx_skb; + struct urb *urbs[0]; +}; + +static void tx_complete(struct urb *req); +static void rx_complete(struct urb *req); + +/* + * Network device callbacks + */ +static int usbpn_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct usbpn_dev *pnd = netdev_priv(dev); + struct urb *req = NULL; + unsigned long flags; + int err; + + if (skb->protocol != htons(ETH_P_PHONET)) + goto drop; + + req = usb_alloc_urb(0, GFP_ATOMIC); + if (!req) + goto drop; + usb_fill_bulk_urb(req, pnd->usb, pnd->tx_pipe, skb->data, skb->len, + tx_complete, skb); + req->transfer_flags = URB_ZERO_PACKET; + err = usb_submit_urb(req, GFP_ATOMIC); + if (err) { + usb_free_urb(req); + goto drop; + } + + spin_lock_irqsave(&pnd->tx_lock, flags); + pnd->tx_queue++; + if (pnd->tx_queue >= dev->tx_queue_len) + netif_stop_queue(dev); + spin_unlock_irqrestore(&pnd->tx_lock, flags); + return 0; + +drop: + dev_kfree_skb(skb); + dev->stats.tx_dropped++; + return 0; +} + +static void tx_complete(struct urb *req) +{ + struct sk_buff *skb = req->context; + struct net_device *dev = skb->dev; + struct usbpn_dev *pnd = netdev_priv(dev); + + switch (req->status) { + case 0: + dev->stats.tx_bytes += skb->len; + break; + + case -ENOENT: + case -ECONNRESET: + case -ESHUTDOWN: + dev->stats.tx_aborted_errors++; + default: + dev->stats.tx_errors++; + dev_dbg(&dev->dev, "TX error (%d)\n", req->status); + } + dev->stats.tx_packets++; + + spin_lock(&pnd->tx_lock); + pnd->tx_queue--; + netif_wake_queue(dev); + spin_unlock(&pnd->tx_lock); + + dev_kfree_skb_any(skb); + usb_free_urb(req); +} + +static int rx_submit(struct usbpn_dev *pnd, struct urb *req, gfp_t gfp_flags) +{ + struct net_device *dev = pnd->dev; + struct page *page; + int err; + + page = __netdev_alloc_page(dev, gfp_flags); + if (!page) + return -ENOMEM; + + usb_fill_bulk_urb(req, pnd->usb, pnd->rx_pipe, page_address(page), + PAGE_SIZE, rx_complete, dev); + req->transfer_flags = 0; + err = usb_submit_urb(req, gfp_flags); + if (unlikely(err)) { + dev_dbg(&dev->dev, "RX submit error (%d)\n", err); + netdev_free_page(dev, page); + } + return err; +} + +static void rx_complete(struct urb *req) +{ + struct net_device *dev = req->context; + struct usbpn_dev *pnd = netdev_priv(dev); + struct page *page = virt_to_page(req->transfer_buffer); + struct sk_buff *skb; + unsigned long flags; + + switch (req->status) { + case 0: + spin_lock_irqsave(&pnd->rx_lock, flags); + skb = pnd->rx_skb; + if (!skb) { + skb = pnd->rx_skb = netdev_alloc_skb(dev, 12); + if (likely(skb)) { + /* Can't use pskb_pull() on page in IRQ */ + memcpy(skb_put(skb, 1), page_address(page), 1); + skb_add_rx_frag(skb, skb_shinfo(skb)->nr_frags, + page, 1, req->actual_length); + page = NULL; + } + } else { + skb_add_rx_frag(skb, skb_shinfo(skb)->nr_frags, + page, 0, req->actual_length); + page = NULL; + } + if (req->actual_length < PAGE_SIZE) + pnd->rx_skb = NULL; /* Last fragment */ + else + skb = NULL; + spin_unlock_irqrestore(&pnd->rx_lock, flags); + if (skb) { + skb->protocol = htons(ETH_P_PHONET); + skb_reset_mac_header(skb); + __skb_pull(skb, 1); + skb->dev = dev; + dev->stats.rx_packets++; + dev->stats.rx_bytes += skb->len; + + netif_rx(skb); + } + goto resubmit; + + case -ENOENT: + case -ECONNRESET: + case -ESHUTDOWN: + req = NULL; + break; + + case -EOVERFLOW: + dev->stats.rx_over_errors++; + dev_dbg(&dev->dev, "RX overflow\n"); + break; + + case -EILSEQ: + dev->stats.rx_crc_errors++; + break; + } + + dev->stats.rx_errors++; +resubmit: + if (page) + netdev_free_page(dev, page); + if (req) + rx_submit(pnd, req, GFP_ATOMIC); +} + +static int usbpn_close(struct net_device *dev); + +static int usbpn_open(struct net_device *dev) +{ + struct usbpn_dev *pnd = netdev_priv(dev); + int err; + unsigned i; + unsigned num = pnd->data_intf->cur_altsetting->desc.bInterfaceNumber; + + err = usb_set_interface(pnd->usb, num, pnd->active_setting); + if (err) + return err; + + for (i = 0; i < rxq_size; i++) { + struct urb *req = usb_alloc_urb(0, GFP_KERNEL); + + if (!req || rx_submit(pnd, req, GFP_KERNEL)) { + usbpn_close(dev); + return -ENOMEM; + } + pnd->urbs[i] = req; + } + + netif_wake_queue(dev); + return 0; +} + +static int usbpn_close(struct net_device *dev) +{ + struct usbpn_dev *pnd = netdev_priv(dev); + unsigned i; + unsigned num = pnd->data_intf->cur_altsetting->desc.bInterfaceNumber; + + netif_stop_queue(dev); + + for (i = 0; i < rxq_size; i++) { + struct urb *req = pnd->urbs[i]; + + if (!req) + continue; + usb_kill_urb(req); + usb_free_urb(req); + pnd->urbs[i] = NULL; + } + + return usb_set_interface(pnd->usb, num, !pnd->active_setting); +} + +static int usbpn_set_mtu(struct net_device *dev, int new_mtu) +{ + if ((new_mtu < PHONET_MIN_MTU) || (new_mtu > PHONET_MAX_MTU)) + return -EINVAL; + + dev->mtu = new_mtu; + return 0; +} + +static const struct net_device_ops usbpn_ops = { + .ndo_open = usbpn_open, + .ndo_stop = usbpn_close, + .ndo_start_xmit = usbpn_xmit, + .ndo_change_mtu = usbpn_set_mtu, +}; + +static void usbpn_setup(struct net_device *dev) +{ + dev->features = 0; + dev->netdev_ops = &usbpn_ops, + dev->header_ops = &phonet_header_ops; + dev->type = ARPHRD_PHONET; + dev->flags = IFF_POINTOPOINT | IFF_NOARP; + dev->mtu = PHONET_MAX_MTU; + dev->hard_header_len = 1; + dev->dev_addr[0] = PN_MEDIA_USB; + dev->addr_len = 1; + dev->tx_queue_len = 3; + + dev->destructor = free_netdev; +} + +/* + * USB driver callbacks + */ +static struct usb_device_id usbpn_ids[] = { + { + .match_flags = USB_DEVICE_ID_MATCH_VENDOR + | USB_DEVICE_ID_MATCH_INT_CLASS + | USB_DEVICE_ID_MATCH_INT_SUBCLASS, + .idVendor = 0x0421, /* Nokia */ + .bInterfaceClass = USB_CLASS_COMM, + .bInterfaceSubClass = 0xFE, + }, + { }, +}; + +MODULE_DEVICE_TABLE(usb, usbpn_ids); + +static struct usb_driver usbpn_driver; + +int usbpn_probe(struct usb_interface *intf, const struct usb_device_id *id) +{ + static const char ifname[] = "usbpn%d"; + const struct usb_cdc_union_desc *union_header = NULL; + const struct usb_cdc_header_desc *phonet_header = NULL; + const struct usb_host_interface *data_desc; + struct usb_interface *data_intf; + struct usb_device *usbdev = interface_to_usbdev(intf); + struct net_device *dev; + struct usbpn_dev *pnd; + u8 *data; + int len, err; + + data = intf->altsetting->extra; + len = intf->altsetting->extralen; + while (len >= 3) { + u8 dlen = data[0]; + if (dlen < 3) + return -EINVAL; + + /* bDescriptorType */ + if (data[1] == USB_DT_CS_INTERFACE) { + /* bDescriptorSubType */ + switch (data[2]) { + case USB_CDC_UNION_TYPE: + if (union_header || dlen < 5) + break; + union_header = + (struct usb_cdc_union_desc *)data; + break; + case 0xAB: + if (phonet_header || dlen < 5) + break; + phonet_header = + (struct usb_cdc_header_desc *)data; + break; + } + } + data += dlen; + len -= dlen; + } + + if (!union_header || !phonet_header) + return -EINVAL; + + data_intf = usb_ifnum_to_if(usbdev, union_header->bSlaveInterface0); + if (data_intf == NULL) + return -ENODEV; + /* Data interface has one inactive and one active setting */ + if (data_intf->num_altsetting != 2) + return -EINVAL; + if (data_intf->altsetting[0].desc.bNumEndpoints == 0 + && data_intf->altsetting[1].desc.bNumEndpoints == 2) + data_desc = data_intf->altsetting + 1; + else + if (data_intf->altsetting[0].desc.bNumEndpoints == 2 + && data_intf->altsetting[1].desc.bNumEndpoints == 0) + data_desc = data_intf->altsetting; + else + return -EINVAL; + + dev = alloc_netdev(sizeof(*pnd) + sizeof(pnd->urbs[0]) * rxq_size, + ifname, usbpn_setup); + if (!dev) + return -ENOMEM; + + pnd = netdev_priv(dev); + SET_NETDEV_DEV(dev, &intf->dev); + netif_stop_queue(dev); + + pnd->dev = dev; + pnd->usb = usb_get_dev(usbdev); + pnd->intf = intf; + pnd->data_intf = data_intf; + spin_lock_init(&pnd->tx_lock); + spin_lock_init(&pnd->rx_lock); + /* Endpoints */ + if (usb_pipein(data_desc->endpoint[0].desc.bEndpointAddress)) { + pnd->rx_pipe = usb_rcvbulkpipe(usbdev, + data_desc->endpoint[0].desc.bEndpointAddress); + pnd->tx_pipe = usb_sndbulkpipe(usbdev, + data_desc->endpoint[1].desc.bEndpointAddress); + } else { + pnd->rx_pipe = usb_rcvbulkpipe(usbdev, + data_desc->endpoint[1].desc.bEndpointAddress); + pnd->tx_pipe = usb_sndbulkpipe(usbdev, + data_desc->endpoint[0].desc.bEndpointAddress); + } + pnd->active_setting = data_desc - data_intf->altsetting; + + err = usb_driver_claim_interface(&usbpn_driver, data_intf, pnd); + if (err) + goto out; + + /* Force inactive mode until the network device is brought UP */ + usb_set_interface(usbdev, union_header->bSlaveInterface0, + !pnd->active_setting); + usb_set_intfdata(intf, pnd); + + err = register_netdev(dev); + if (err) { + usb_driver_release_interface(&usbpn_driver, data_intf); + goto out; + } + + dev_dbg(&dev->dev, "USB CDC Phonet device found\n"); + return 0; + +out: + usb_set_intfdata(intf, NULL); + free_netdev(dev); + return err; +} + +static void usbpn_disconnect(struct usb_interface *intf) +{ + struct usbpn_dev *pnd = usb_get_intfdata(intf); + struct usb_device *usb = pnd->usb; + + if (pnd->disconnected) + return; + + pnd->disconnected = 1; + usb_driver_release_interface(&usbpn_driver, + (pnd->intf == intf) ? pnd->data_intf : pnd->intf); + unregister_netdev(pnd->dev); + usb_put_dev(usb); +} + +static struct usb_driver usbpn_driver = { + .name = "cdc_phonet", + .probe = usbpn_probe, + .disconnect = usbpn_disconnect, + .id_table = usbpn_ids, +}; + +static int __init usbpn_init(void) +{ + return usb_register(&usbpn_driver); +} + +static void __exit usbpn_exit(void) +{ + usb_deregister(&usbpn_driver); +} + +module_init(usbpn_init); +module_exit(usbpn_exit); + +MODULE_AUTHOR("Remi Denis-Courmont"); +MODULE_DESCRIPTION("USB CDC Phonet host interface"); +MODULE_LICENSE("GPL"); -- GitLab From acb9c1b2f406d25c381de2b429f65706cc04d3b5 Mon Sep 17 00:00:00 2001 From: Evgeniy Polyakov Date: Tue, 21 Jul 2009 12:43:51 -0700 Subject: [PATCH 0162/1342] connector: maintainer/mail update. Signed-off-by: Evgeniy Polyakov Signed-off-by: David S. Miller --- Documentation/connector/cn_test.c | 4 ++-- Documentation/connector/ucon.c | 2 +- MAINTAINERS | 7 +++++++ drivers/connector/cn_queue.c | 2 +- drivers/connector/connector.c | 4 ++-- 5 files changed, 13 insertions(+), 6 deletions(-) diff --git a/Documentation/connector/cn_test.c b/Documentation/connector/cn_test.c index f688eba8770..6a5be5d5c8e 100644 --- a/Documentation/connector/cn_test.c +++ b/Documentation/connector/cn_test.c @@ -1,7 +1,7 @@ /* * cn_test.c * - * 2004-2005 Copyright (c) Evgeniy Polyakov + * 2004+ Copyright (c) Evgeniy Polyakov * All rights reserved. * * This program is free software; you can redistribute it and/or modify @@ -194,5 +194,5 @@ module_init(cn_test_init); module_exit(cn_test_fini); MODULE_LICENSE("GPL"); -MODULE_AUTHOR("Evgeniy Polyakov "); +MODULE_AUTHOR("Evgeniy Polyakov "); MODULE_DESCRIPTION("Connector's test module"); diff --git a/Documentation/connector/ucon.c b/Documentation/connector/ucon.c index d738cde2a8d..c5092ad0ce4 100644 --- a/Documentation/connector/ucon.c +++ b/Documentation/connector/ucon.c @@ -1,7 +1,7 @@ /* * ucon.c * - * Copyright (c) 2004+ Evgeniy Polyakov + * Copyright (c) 2004+ Evgeniy Polyakov * * * This program is free software; you can redistribute it and/or modify diff --git a/MAINTAINERS b/MAINTAINERS index 6c6bb95acb1..88e8c00ede7 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1569,6 +1569,13 @@ S: Supported F: fs/configfs/ F: include/linux/configfs.h +CONNECTOR +P: Evgeniy Polyakov +M: zbr@ioremap.net +L: netdev@vger.kernel.org +S: Maintained +F: drivers/connector/ + CONTROL GROUPS (CGROUPS) P: Paul Menage M: menage@google.com diff --git a/drivers/connector/cn_queue.c b/drivers/connector/cn_queue.c index c769ef269fb..408c2af25d5 100644 --- a/drivers/connector/cn_queue.c +++ b/drivers/connector/cn_queue.c @@ -1,7 +1,7 @@ /* * cn_queue.c * - * 2004-2005 Copyright (c) Evgeniy Polyakov + * 2004+ Copyright (c) Evgeniy Polyakov * All rights reserved. * * This program is free software; you can redistribute it and/or modify diff --git a/drivers/connector/connector.c b/drivers/connector/connector.c index fd336c5a905..08b2500f21e 100644 --- a/drivers/connector/connector.c +++ b/drivers/connector/connector.c @@ -1,7 +1,7 @@ /* * connector.c * - * 2004-2005 Copyright (c) Evgeniy Polyakov + * 2004+ Copyright (c) Evgeniy Polyakov * All rights reserved. * * This program is free software; you can redistribute it and/or modify @@ -33,7 +33,7 @@ #include MODULE_LICENSE("GPL"); -MODULE_AUTHOR("Evgeniy Polyakov "); +MODULE_AUTHOR("Evgeniy Polyakov "); MODULE_DESCRIPTION("Generic userspace <-> kernelspace connector."); static u32 cn_idx = CN_IDX_CONNECTOR; -- GitLab From ed5c8ef3bb2de277b7885072e0e981c41a022be5 Mon Sep 17 00:00:00 2001 From: Alan Jenkins Date: Sun, 19 Jul 2009 09:48:28 +0100 Subject: [PATCH 0163/1342] acer-wmi: fix rfkill conversion Fix another polarity error introduced by the rfkill rewrite, this time in acer_rfkill_set(). Signed-off-by: Alan Jenkins Signed-off-by: John W. Linville --- drivers/platform/x86/acer-wmi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/platform/x86/acer-wmi.c b/drivers/platform/x86/acer-wmi.c index be2fd6f9163..fb45f5ee8df 100644 --- a/drivers/platform/x86/acer-wmi.c +++ b/drivers/platform/x86/acer-wmi.c @@ -973,7 +973,7 @@ static int acer_rfkill_set(void *data, bool blocked) { acpi_status status; u32 cap = (unsigned long)data; - status = set_u32(!!blocked, cap); + status = set_u32(!blocked, cap); if (ACPI_FAILURE(status)) return -ENODEV; return 0; -- GitLab From bfa99bfdda1ce8a60f1f0fba7a04162a66d4ecfa Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Sun, 19 Jul 2009 21:26:13 +0200 Subject: [PATCH 0164/1342] p54spi: fix potential null deref in p54spi.c Fix a potential NULL dereference bug during error handling in p54spi_probe. This bug was discovered by smatch: (http://repo.or.cz/w/smatch.git). Signed-off-by: Dan Carpenter Signed-off-by: Christian Lamparter Signed-off-by: John W. Linville --- drivers/net/wireless/p54/p54spi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/wireless/p54/p54spi.c b/drivers/net/wireless/p54/p54spi.c index 83116baeb11..72c7dbd39d0 100644 --- a/drivers/net/wireless/p54/p54spi.c +++ b/drivers/net/wireless/p54/p54spi.c @@ -635,7 +635,7 @@ static int __devinit p54spi_probe(struct spi_device *spi) hw = p54_init_common(sizeof(*priv)); if (!hw) { - dev_err(&priv->spi->dev, "could not alloc ieee80211_hw"); + dev_err(&spi->dev, "could not alloc ieee80211_hw"); return -ENOMEM; } -- GitLab From 5d2214ac5e7f72c9ae70b2444649e8d1d3e1086d Mon Sep 17 00:00:00 2001 From: "Luis R. Rodriguez" Date: Mon, 20 Jul 2009 08:32:47 -0700 Subject: [PATCH 0165/1342] ath: add support for special 0x8000 regulatory domain Two users of ar9170 devices have now reported their cards have been programmed with a regulatory domain of 0x8000. This is not a valid regulatory domain as such these users were unable to use these devices. Since this doesn't seem to be a device EEPROM corruption we must treat it specially. It may have been possible the manufacturer intended to use 0x0 as the regulatory domain and that would ultimately yield to US but since we cannot get confirmationf or this we default this special case to one of our world regulatory domains, specifically 0x64. Reported-by: DavidFreeman on #linux-wireless Reported-by: Joerg Albert Cc: Christian Lamparter , Cc: Stephen Chen Cc: David Quan Cc: Tony Yang Signed-off-by: Luis R. Rodriguez Signed-off-by: John W. Linville --- drivers/net/wireless/ath/regd.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) diff --git a/drivers/net/wireless/ath/regd.c b/drivers/net/wireless/ath/regd.c index eef370bd121..bf3d25ba7be 100644 --- a/drivers/net/wireless/ath/regd.c +++ b/drivers/net/wireless/ath/regd.c @@ -474,6 +474,21 @@ ath_regd_init_wiphy(struct ath_regulatory *reg, return 0; } +/* + * Some users have reported their EEPROM programmed with + * 0x8000 set, this is not a supported regulatory domain + * but since we have more than one user with it we need + * a solution for them. We default to 0x64, which is the + * default Atheros world regulatory domain. + */ +static void ath_regd_sanitize(struct ath_regulatory *reg) +{ + if (reg->current_rd != COUNTRY_ERD_FLAG) + return; + printk(KERN_DEBUG "ath: EEPROM regdomain sanitized\n"); + reg->current_rd = 0x64; +} + int ath_regd_init(struct ath_regulatory *reg, struct wiphy *wiphy, @@ -486,6 +501,8 @@ ath_regd_init(struct ath_regulatory *reg, if (!reg) return -EINVAL; + ath_regd_sanitize(reg); + printk(KERN_DEBUG "ath: EEPROM regdomain: 0x%0x\n", reg->current_rd); if (!ath_regd_is_eeprom_valid(reg)) { -- GitLab From 154839962a582b8eb661cde94ef3af0e03b374d7 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Thu, 16 Jul 2009 19:19:53 +0200 Subject: [PATCH 0166/1342] libertas: Fix problem with broken V4 firmware on CF8381 Firmware V4 on CF8381 reports region code shifted by 1 byte to left. The following patch checks for this and handles it properly. Signed-off-by: Marek Vasut Signed-off-by: John W. Linville --- drivers/net/wireless/libertas/cmd.c | 8 +++++++- drivers/net/wireless/libertas/defs.h | 2 ++ 2 files changed, 9 insertions(+), 1 deletion(-) diff --git a/drivers/net/wireless/libertas/cmd.c b/drivers/net/wireless/libertas/cmd.c index 01db705a38e..685098148e1 100644 --- a/drivers/net/wireless/libertas/cmd.c +++ b/drivers/net/wireless/libertas/cmd.c @@ -135,8 +135,14 @@ int lbs_update_hw_spec(struct lbs_private *priv) /* Clamp region code to 8-bit since FW spec indicates that it should * only ever be 8-bit, even though the field size is 16-bit. Some firmware * returns non-zero high 8 bits here. + * + * Firmware version 4.0.102 used in CF8381 has region code shifted. We + * need to check for this problem and handle it properly. */ - priv->regioncode = le16_to_cpu(cmd.regioncode) & 0xFF; + if (MRVL_FW_MAJOR_REV(priv->fwrelease) == MRVL_FW_V4) + priv->regioncode = (le16_to_cpu(cmd.regioncode) >> 8) & 0xFF; + else + priv->regioncode = le16_to_cpu(cmd.regioncode) & 0xFF; for (i = 0; i < MRVDRV_MAX_REGION_CODE; i++) { /* use the region code to search for the index */ diff --git a/drivers/net/wireless/libertas/defs.h b/drivers/net/wireless/libertas/defs.h index 48da157d6cd..72f3479a4d7 100644 --- a/drivers/net/wireless/libertas/defs.h +++ b/drivers/net/wireless/libertas/defs.h @@ -234,6 +234,8 @@ static inline void lbs_deb_hex(unsigned int grp, const char *prompt, u8 *buf, in /** Mesh enable bit in FW capability */ #define MESH_CAPINFO_ENABLE_MASK (1<<16) +/** FW definition from Marvell v4 */ +#define MRVL_FW_V4 (0x04) /** FW definition from Marvell v5 */ #define MRVL_FW_V5 (0x05) /** FW definition from Marvell v10 */ -- GitLab From 0021195c40326ac4702faf28c32accd91b331641 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Sun, 19 Jul 2009 06:13:04 +0000 Subject: [PATCH 0167/1342] drivers/net: Move a dereference below a NULL test If the NULL test is necessary, then the dereferences should be moved below the NULL test. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // @@ type T; expression E,E1; identifier i,fld; statement S; @@ - T i = E->fld; + T i; ... when != E=E1 when != i BUG_ON (E == NULL||...); + i = E->fld; // Signed-off-by: Julia Lawall Signed-off-by: David S. Miller --- drivers/net/ibm_newemac/rgmii.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/net/ibm_newemac/rgmii.c b/drivers/net/ibm_newemac/rgmii.c index 1d5379de690..8d76cb89dbd 100644 --- a/drivers/net/ibm_newemac/rgmii.c +++ b/drivers/net/ibm_newemac/rgmii.c @@ -188,11 +188,12 @@ void rgmii_put_mdio(struct of_device *ofdev, int input) void rgmii_detach(struct of_device *ofdev, int input) { struct rgmii_instance *dev = dev_get_drvdata(&ofdev->dev); - struct rgmii_regs __iomem *p = dev->base; - - mutex_lock(&dev->lock); + struct rgmii_regs __iomem *p; BUG_ON(!dev || dev->users == 0); + p = dev->base; + + mutex_lock(&dev->lock); RGMII_DBG(dev, "detach(%d)" NL, input); -- GitLab From 0376d5b25ef11e9b6450ebae20781a32d8985170 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Sun, 19 Jul 2009 05:26:35 +0000 Subject: [PATCH 0168/1342] drivers/net: Move a dereference below a NULL test If the NULL test is necessary, then the dereference should be moved below the NULL test. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // @@ type T; expression E,E1; identifier i,fld; statement S; @@ - T i = E->fld; + T i; ... when != E=E1 when != i if (E == NULL||...) S + i = E->fld; // Signed-off-by: Julia Lawall Signed-off-by: David S. Miller --- drivers/net/bnx2x_link.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/net/bnx2x_link.c b/drivers/net/bnx2x_link.c index ed648acef7c..2ee581a2cde 100644 --- a/drivers/net/bnx2x_link.c +++ b/drivers/net/bnx2x_link.c @@ -4212,13 +4212,14 @@ static void bnx2x_turn_off_sf(struct bnx2x *bp, u8 port) u8 bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded, u8 *version, u16 len) { - struct bnx2x *bp = params->bp; + struct bnx2x *bp; u32 ext_phy_type = 0; u32 spirom_ver = 0; u8 status = 0 ; if (version == NULL || params == NULL) return -EINVAL; + bp = params->bp; spirom_ver = REG_RD(bp, params->shmem_base + offsetof(struct shmem_region, -- GitLab From 86669530d966ca21f4245b9990e7ae188d433d1e Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Sun, 19 Jul 2009 06:09:25 +0000 Subject: [PATCH 0169/1342] drivers/net/mlx4: Adjust constant The values in the advertising field are typically ADVERTISED_xxx, not SUPPORTED_xxx. Both SUPPORTED_10000baseT_Full and ADVERTISED_1000baseT_Full have the same value. The semantic match that finds this problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // @@ struct ethtool_cmd E; @@ *E.advertising = SUPPORTED_10000baseT_Full // Signed-off-by: Julia Lawall Signed-off-by: David S. Miller --- drivers/net/mlx4/en_ethtool.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/mlx4/en_ethtool.c b/drivers/net/mlx4/en_ethtool.c index 091f99052c9..86467b444ac 100644 --- a/drivers/net/mlx4/en_ethtool.c +++ b/drivers/net/mlx4/en_ethtool.c @@ -220,7 +220,7 @@ static int mlx4_en_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) { cmd->autoneg = AUTONEG_DISABLE; cmd->supported = SUPPORTED_10000baseT_Full; - cmd->advertising = SUPPORTED_10000baseT_Full; + cmd->advertising = ADVERTISED_1000baseT_Full; if (netif_carrier_ok(dev)) { cmd->speed = SPEED_10000; cmd->duplex = DUPLEX_FULL; -- GitLab From b64aec8d1e1d8482a7b6cca60c8105c756bf1fe4 Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Tue, 21 Jul 2009 16:47:46 -0400 Subject: [PATCH 0170/1342] NFSv4: Fix an Oops in nfs4_free_lock_state The oops http://www.kerneloops.org/raw.php?rawid=537858&msgid= appears to be due to the nfs4_lock_state->ls_state field being uninitialised. This happens if the call to nfs4_free_lock_state() is triggered at the end of nfs4_get_lock_state(). The fix is to move the initialisation of ls_state into the allocator. Signed-off-by: Trond Myklebust --- fs/nfs/nfs4state.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/nfs/nfs4state.c b/fs/nfs/nfs4state.c index b73c5a72865..65ca8c18476 100644 --- a/fs/nfs/nfs4state.c +++ b/fs/nfs/nfs4state.c @@ -553,6 +553,7 @@ static struct nfs4_lock_state *nfs4_alloc_lock_state(struct nfs4_state *state, f INIT_LIST_HEAD(&lsp->ls_sequence.list); lsp->ls_seqid.sequence = &lsp->ls_sequence; atomic_set(&lsp->ls_count, 1); + lsp->ls_state = state; lsp->ls_owner = fl_owner; spin_lock(&clp->cl_lock); nfs_alloc_unique_id(&clp->cl_lockowner_id, &lsp->ls_id, 1, 64); @@ -587,7 +588,6 @@ static struct nfs4_lock_state *nfs4_get_lock_state(struct nfs4_state *state, fl_ if (lsp != NULL) break; if (new != NULL) { - new->ls_state = state; list_add(&new->ls_locks, &state->lock_states); set_bit(LK_STATE_IN_USE, &state->flags); lsp = new; -- GitLab From fccba8045537f7e840d0e7565e1989d465e488a3 Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Tue, 21 Jul 2009 16:48:07 -0400 Subject: [PATCH 0171/1342] NFSv4: Fix an NFSv4 mount regression Commit 008f55d0e019943323c20a03493a2ba5672a4cc8 (nfs41: recover lease in _nfs4_lookup_root) forces the state manager to always run on mount. This is a bug in the case of NFSv4.0, which doesn't require us to send a setclientid until we want to grab file state. In any case, this is completely the wrong place to be doing state management. Moving that code into nfs4_init_session... Signed-off-by: Trond Myklebust --- fs/nfs/client.c | 18 +++--------------- fs/nfs/nfs4_fs.h | 6 ++++++ fs/nfs/nfs4proc.c | 24 +++++++++++++++++------- 3 files changed, 26 insertions(+), 22 deletions(-) diff --git a/fs/nfs/client.c b/fs/nfs/client.c index c2d061675d8..8d25ccb2d51 100644 --- a/fs/nfs/client.c +++ b/fs/nfs/client.c @@ -1242,20 +1242,6 @@ error: return error; } -/* - * Initialize a session. - * Note: save the mount rsize and wsize for create_server negotiation. - */ -static void nfs4_init_session(struct nfs_client *clp, - unsigned int wsize, unsigned int rsize) -{ -#if defined(CONFIG_NFS_V4_1) - if (nfs4_has_session(clp)) { - clp->cl_session->fc_attrs.max_rqst_sz = wsize; - clp->cl_session->fc_attrs.max_resp_sz = rsize; - } -#endif /* CONFIG_NFS_V4_1 */ -} /* * Session has been established, and the client marked ready. @@ -1350,7 +1336,9 @@ struct nfs_server *nfs4_create_server(const struct nfs_parsed_mount_data *data, BUG_ON(!server->nfs_client->rpc_ops); BUG_ON(!server->nfs_client->rpc_ops->file_inode_ops); - nfs4_init_session(server->nfs_client, server->wsize, server->rsize); + error = nfs4_init_session(server); + if (error < 0) + goto error; /* Probe the root fh to retrieve its FSID */ error = nfs4_path_walk(server, mntfh, data->nfs_server.export_path); diff --git a/fs/nfs/nfs4_fs.h b/fs/nfs/nfs4_fs.h index 61bc3a32e1e..6ea07a3c75d 100644 --- a/fs/nfs/nfs4_fs.h +++ b/fs/nfs/nfs4_fs.h @@ -220,6 +220,7 @@ extern void nfs4_destroy_session(struct nfs4_session *session); extern struct nfs4_session *nfs4_alloc_session(struct nfs_client *clp); extern int nfs4_proc_create_session(struct nfs_client *, int reset); extern int nfs4_proc_destroy_session(struct nfs4_session *); +extern int nfs4_init_session(struct nfs_server *server); #else /* CONFIG_NFS_v4_1 */ static inline int nfs4_setup_sequence(struct nfs_client *clp, struct nfs4_sequence_args *args, struct nfs4_sequence_res *res, @@ -227,6 +228,11 @@ static inline int nfs4_setup_sequence(struct nfs_client *clp, { return 0; } + +static inline int nfs4_init_session(struct nfs_server *server) +{ + return 0; +} #endif /* CONFIG_NFS_V4_1 */ extern struct nfs4_state_maintenance_ops *nfs4_state_renewal_ops[]; diff --git a/fs/nfs/nfs4proc.c b/fs/nfs/nfs4proc.c index ff0c080db59..df24f67bca6 100644 --- a/fs/nfs/nfs4proc.c +++ b/fs/nfs/nfs4proc.c @@ -2040,15 +2040,9 @@ static int _nfs4_lookup_root(struct nfs_server *server, struct nfs_fh *fhandle, .rpc_argp = &args, .rpc_resp = &res, }; - int status; nfs_fattr_init(info->fattr); - status = nfs4_recover_expired_lease(server); - if (!status) - status = nfs4_check_client_ready(server->nfs_client); - if (!status) - status = nfs4_call_sync(server, &msg, &args, &res, 0); - return status; + return nfs4_call_sync(server, &msg, &args, &res, 0); } static int nfs4_lookup_root(struct nfs_server *server, struct nfs_fh *fhandle, @@ -4793,6 +4787,22 @@ int nfs4_proc_destroy_session(struct nfs4_session *session) return status; } +int nfs4_init_session(struct nfs_server *server) +{ + struct nfs_client *clp = server->nfs_client; + int ret; + + if (!nfs4_has_session(clp)) + return 0; + + clp->cl_session->fc_attrs.max_rqst_sz = server->wsize; + clp->cl_session->fc_attrs.max_resp_sz = server->rsize; + ret = nfs4_recover_expired_lease(server); + if (!ret) + ret = nfs4_check_client_ready(clp); + return ret; +} + /* * Renew the cl_session lease. */ -- GitLab From 3c5e10683e684ef45614c9071847e48f633d9806 Mon Sep 17 00:00:00 2001 From: Tao Ma Date: Tue, 21 Jul 2009 15:42:05 +0800 Subject: [PATCH 0172/1342] ocfs2: Add extra credits and access the modified bh in update_edge_lengths. In normal tree rotation left process, we will never touch the tree branch above subtree_index and ocfs2_extend_rotate_transaction doesn't reserve the credits for them either. But when we want to delete the rightmost extent block, we have to update the rightmost records for all the rightmost branch(See ocfs2_update_edge_lengths), so we have to allocate extra credits for them. What's more, we have to access them also. Signed-off-by: Tao Ma Signed-off-by: Joel Becker --- fs/ocfs2/alloc.c | 44 +++++++++++++++++++++++++++++++++++++++----- 1 file changed, 39 insertions(+), 5 deletions(-) diff --git a/fs/ocfs2/alloc.c b/fs/ocfs2/alloc.c index 9edcde4974a..11085af7124 100644 --- a/fs/ocfs2/alloc.c +++ b/fs/ocfs2/alloc.c @@ -2476,15 +2476,37 @@ out_ret_path: return ret; } -static void ocfs2_update_edge_lengths(struct inode *inode, handle_t *handle, - struct ocfs2_path *path) +static int ocfs2_update_edge_lengths(struct inode *inode, handle_t *handle, + int subtree_index, struct ocfs2_path *path) { - int i, idx; + int i, idx, ret; struct ocfs2_extent_rec *rec; struct ocfs2_extent_list *el; struct ocfs2_extent_block *eb; u32 range; + /* + * In normal tree rotation process, we will never touch the + * tree branch above subtree_index and ocfs2_extend_rotate_transaction + * doesn't reserve the credits for them either. + * + * But we do have a special case here which will update the rightmost + * records for all the bh in the path. + * So we have to allocate extra credits and access them. + */ + ret = ocfs2_extend_trans(handle, + handle->h_buffer_credits + subtree_index); + if (ret) { + mlog_errno(ret); + goto out; + } + + ret = ocfs2_journal_access_path(inode, handle, path); + if (ret) { + mlog_errno(ret); + goto out; + } + /* Path should always be rightmost. */ eb = (struct ocfs2_extent_block *)path_leaf_bh(path)->b_data; BUG_ON(eb->h_next_leaf_blk != 0ULL); @@ -2505,6 +2527,8 @@ static void ocfs2_update_edge_lengths(struct inode *inode, handle_t *handle, ocfs2_journal_dirty(handle, path->p_node[i].bh); } +out: + return ret; } static void ocfs2_unlink_path(struct inode *inode, handle_t *handle, @@ -2717,7 +2741,12 @@ static int ocfs2_rotate_subtree_left(struct inode *inode, handle_t *handle, if (del_right_subtree) { ocfs2_unlink_subtree(inode, handle, left_path, right_path, subtree_index, dealloc); - ocfs2_update_edge_lengths(inode, handle, left_path); + ret = ocfs2_update_edge_lengths(inode, handle, subtree_index, + left_path); + if (ret) { + mlog_errno(ret); + goto out; + } eb = (struct ocfs2_extent_block *)path_leaf_bh(left_path)->b_data; ocfs2_et_set_last_eb_blk(et, le64_to_cpu(eb->h_blkno)); @@ -3034,7 +3063,12 @@ static int ocfs2_remove_rightmost_path(struct inode *inode, handle_t *handle, ocfs2_unlink_subtree(inode, handle, left_path, path, subtree_index, dealloc); - ocfs2_update_edge_lengths(inode, handle, left_path); + ret = ocfs2_update_edge_lengths(inode, handle, subtree_index, + left_path); + if (ret) { + mlog_errno(ret); + goto out; + } eb = (struct ocfs2_extent_block *)path_leaf_bh(left_path)->b_data; ocfs2_et_set_last_eb_blk(et, le64_to_cpu(eb->h_blkno)); -- GitLab From 429b2b319af3987e808c18f6b81313104caf782c Mon Sep 17 00:00:00 2001 From: Andi Kleen Date: Sat, 18 Jul 2009 08:56:57 +0200 Subject: [PATCH 0173/1342] x86-64: Fix bad_srat() to clear all state Need to clear both nodes and nodes_add state for start/end. Signed-off-by: Andi Kleen LKML-Reference: <20090718065657.GA2898@basil.fritz.box> Signed-off-by: H. Peter Anvin Cc: stable@kernel.org --- arch/x86/mm/srat_64.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/arch/x86/mm/srat_64.c b/arch/x86/mm/srat_64.c index 2dfcbf9df2a..dbb5381f7b3 100644 --- a/arch/x86/mm/srat_64.c +++ b/arch/x86/mm/srat_64.c @@ -79,8 +79,10 @@ static __init void bad_srat(void) acpi_numa = -1; for (i = 0; i < MAX_LOCAL_APIC; i++) apicid_to_node[i] = NUMA_NO_NODE; - for (i = 0; i < MAX_NUMNODES; i++) - nodes_add[i].start = nodes[i].end = 0; + for (i = 0; i < MAX_NUMNODES; i++) { + nodes[i].start = nodes[i].end = 0; + nodes_add[i].start = nodes_add[i].end = 0; + } remove_all_active_ranges(); } -- GitLab From f7b1aa69be138ad9d7d3f31fa56f4c9407f56b6a Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Mon, 20 Jul 2009 12:12:36 +0200 Subject: [PATCH 0174/1342] ocfs2: Fix deadlock on umount In commit ea455f8ab68338ba69f5d3362b342c115bea8e13, we moved the dentry lock put process into ocfs2_wq. This causes problems during umount because ocfs2_wq can drop references to inodes while they are being invalidated by invalidate_inodes() causing all sorts of nasty things (invalidate_inodes() ending in an infinite loop, "Busy inodes after umount" messages etc.). We fix the problem by stopping ocfs2_wq from doing any further releasing of inode references on the superblock being unmounted, wait until it finishes the current round of releasing and finally cleaning up all the references in dentry_lock_list from ocfs2_put_super(). The issue was tracked down by Tao Ma . Signed-off-by: Jan Kara Signed-off-by: Joel Becker --- fs/ocfs2/dcache.c | 35 +++++++++++++++++++++++++++-------- fs/ocfs2/dcache.h | 3 +++ fs/ocfs2/ocfs2.h | 22 ++++++++++++++++++---- fs/ocfs2/super.c | 25 ++++++++++++++++++++++--- 4 files changed, 70 insertions(+), 15 deletions(-) diff --git a/fs/ocfs2/dcache.c b/fs/ocfs2/dcache.c index b574431a031..2f28b7de2c8 100644 --- a/fs/ocfs2/dcache.c +++ b/fs/ocfs2/dcache.c @@ -310,22 +310,19 @@ out_attach: return ret; } -static DEFINE_SPINLOCK(dentry_list_lock); +DEFINE_SPINLOCK(dentry_list_lock); /* We limit the number of dentry locks to drop in one go. We have * this limit so that we don't starve other users of ocfs2_wq. */ #define DL_INODE_DROP_COUNT 64 /* Drop inode references from dentry locks */ -void ocfs2_drop_dl_inodes(struct work_struct *work) +static void __ocfs2_drop_dl_inodes(struct ocfs2_super *osb, int drop_count) { - struct ocfs2_super *osb = container_of(work, struct ocfs2_super, - dentry_lock_work); struct ocfs2_dentry_lock *dl; - int drop_count = DL_INODE_DROP_COUNT; spin_lock(&dentry_list_lock); - while (osb->dentry_lock_list && drop_count--) { + while (osb->dentry_lock_list && (drop_count < 0 || drop_count--)) { dl = osb->dentry_lock_list; osb->dentry_lock_list = dl->dl_next; spin_unlock(&dentry_list_lock); @@ -333,11 +330,32 @@ void ocfs2_drop_dl_inodes(struct work_struct *work) kfree(dl); spin_lock(&dentry_list_lock); } - if (osb->dentry_lock_list) + spin_unlock(&dentry_list_lock); +} + +void ocfs2_drop_dl_inodes(struct work_struct *work) +{ + struct ocfs2_super *osb = container_of(work, struct ocfs2_super, + dentry_lock_work); + + __ocfs2_drop_dl_inodes(osb, DL_INODE_DROP_COUNT); + /* + * Don't queue dropping if umount is in progress. We flush the + * list in ocfs2_dismount_volume + */ + spin_lock(&dentry_list_lock); + if (osb->dentry_lock_list && + !ocfs2_test_osb_flag(osb, OCFS2_OSB_DROP_DENTRY_LOCK_IMMED)) queue_work(ocfs2_wq, &osb->dentry_lock_work); spin_unlock(&dentry_list_lock); } +/* Flush the whole work queue */ +void ocfs2_drop_all_dl_inodes(struct ocfs2_super *osb) +{ + __ocfs2_drop_dl_inodes(osb, -1); +} + /* * ocfs2_dentry_iput() and friends. * @@ -368,7 +386,8 @@ static void ocfs2_drop_dentry_lock(struct ocfs2_super *osb, /* We leave dropping of inode reference to ocfs2_wq as that can * possibly lead to inode deletion which gets tricky */ spin_lock(&dentry_list_lock); - if (!osb->dentry_lock_list) + if (!osb->dentry_lock_list && + !ocfs2_test_osb_flag(osb, OCFS2_OSB_DROP_DENTRY_LOCK_IMMED)) queue_work(ocfs2_wq, &osb->dentry_lock_work); dl->dl_next = osb->dentry_lock_list; osb->dentry_lock_list = dl; diff --git a/fs/ocfs2/dcache.h b/fs/ocfs2/dcache.h index faa12e75f98..f5dd1789acf 100644 --- a/fs/ocfs2/dcache.h +++ b/fs/ocfs2/dcache.h @@ -49,10 +49,13 @@ struct ocfs2_dentry_lock { int ocfs2_dentry_attach_lock(struct dentry *dentry, struct inode *inode, u64 parent_blkno); +extern spinlock_t dentry_list_lock; + void ocfs2_dentry_lock_put(struct ocfs2_super *osb, struct ocfs2_dentry_lock *dl); void ocfs2_drop_dl_inodes(struct work_struct *work); +void ocfs2_drop_all_dl_inodes(struct ocfs2_super *osb); struct dentry *ocfs2_find_local_alias(struct inode *inode, u64 parent_blkno, int skip_unhashed); diff --git a/fs/ocfs2/ocfs2.h b/fs/ocfs2/ocfs2.h index c9345ebb849..39e1d5a3950 100644 --- a/fs/ocfs2/ocfs2.h +++ b/fs/ocfs2/ocfs2.h @@ -224,10 +224,12 @@ enum ocfs2_mount_options OCFS2_MOUNT_GRPQUOTA = 1 << 10, /* We support group quotas */ }; -#define OCFS2_OSB_SOFT_RO 0x0001 -#define OCFS2_OSB_HARD_RO 0x0002 -#define OCFS2_OSB_ERROR_FS 0x0004 -#define OCFS2_DEFAULT_ATIME_QUANTUM 60 +#define OCFS2_OSB_SOFT_RO 0x0001 +#define OCFS2_OSB_HARD_RO 0x0002 +#define OCFS2_OSB_ERROR_FS 0x0004 +#define OCFS2_OSB_DROP_DENTRY_LOCK_IMMED 0x0008 + +#define OCFS2_DEFAULT_ATIME_QUANTUM 60 struct ocfs2_journal; struct ocfs2_slot_info; @@ -490,6 +492,18 @@ static inline void ocfs2_set_osb_flag(struct ocfs2_super *osb, spin_unlock(&osb->osb_lock); } + +static inline unsigned long ocfs2_test_osb_flag(struct ocfs2_super *osb, + unsigned long flag) +{ + unsigned long ret; + + spin_lock(&osb->osb_lock); + ret = osb->osb_flags & flag; + spin_unlock(&osb->osb_lock); + return ret; +} + static inline void ocfs2_set_ro_flag(struct ocfs2_super *osb, int hard) { diff --git a/fs/ocfs2/super.c b/fs/ocfs2/super.c index 63af2e36d83..f2893878f8a 100644 --- a/fs/ocfs2/super.c +++ b/fs/ocfs2/super.c @@ -1213,14 +1213,27 @@ static int ocfs2_get_sb(struct file_system_type *fs_type, mnt); } +static void ocfs2_kill_sb(struct super_block *sb) +{ + struct ocfs2_super *osb = OCFS2_SB(sb); + + /* Prevent further queueing of inode drop events */ + spin_lock(&dentry_list_lock); + ocfs2_set_osb_flag(osb, OCFS2_OSB_DROP_DENTRY_LOCK_IMMED); + spin_unlock(&dentry_list_lock); + /* Wait for work to finish and/or remove it */ + cancel_work_sync(&osb->dentry_lock_work); + + kill_block_super(sb); +} + static struct file_system_type ocfs2_fs_type = { .owner = THIS_MODULE, .name = "ocfs2", .get_sb = ocfs2_get_sb, /* is this called when we mount * the fs? */ - .kill_sb = kill_block_super, /* set to the generic one - * right now, but do we - * need to change that? */ + .kill_sb = ocfs2_kill_sb, + .fs_flags = FS_REQUIRES_DEV|FS_RENAME_DOES_D_MOVE, .next = NULL }; @@ -1819,6 +1832,12 @@ static void ocfs2_dismount_volume(struct super_block *sb, int mnt_err) debugfs_remove(osb->osb_ctxt); + /* + * Flush inode dropping work queue so that deletes are + * performed while the filesystem is still working + */ + ocfs2_drop_all_dl_inodes(osb); + /* Orphan scan should be stopped as early as possible */ ocfs2_orphan_scan_stop(osb); -- GitLab From d953126a28f97ec965d23c69fd5795854c048f30 Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Tue, 21 Jul 2009 19:22:38 -0400 Subject: [PATCH 0175/1342] NFSv4: Fix a problem whereby a buggy server can oops the kernel We just had a case in which a buggy server occasionally returns the wrong attributes during an OPEN call. While the client does catch this sort of condition in nfs4_open_done(), and causes the nfs4_atomic_open() to return -EISDIR, the logic in nfs_atomic_lookup() is broken, since it causes a fallback to an ordinary lookup instead of just returning the error. When the buggy server then returns a regular file for the fallback lookup, the VFS allows the open, and bad things start to happen, since the open file doesn't have any associated NFSv4 state. The fix is firstly to return the EISDIR/ENOTDIR errors immediately, and secondly to ensure that we are always careful when dereferencing the nfs_open_context state pointer. Signed-off-by: Trond Myklebust --- fs/nfs/dir.c | 2 +- fs/nfs/nfs4proc.c | 16 ++++++++++++---- 2 files changed, 13 insertions(+), 5 deletions(-) diff --git a/fs/nfs/dir.c b/fs/nfs/dir.c index 38d42c29fb9..32062c33c85 100644 --- a/fs/nfs/dir.c +++ b/fs/nfs/dir.c @@ -1025,12 +1025,12 @@ static struct dentry *nfs_atomic_lookup(struct inode *dir, struct dentry *dentry res = NULL; goto out; /* This turned out not to be a regular file */ - case -EISDIR: case -ENOTDIR: goto no_open; case -ELOOP: if (!(nd->intent.open.flags & O_NOFOLLOW)) goto no_open; + /* case -EISDIR: */ /* case -EINVAL: */ default: goto out; diff --git a/fs/nfs/nfs4proc.c b/fs/nfs/nfs4proc.c index df24f67bca6..6917311f201 100644 --- a/fs/nfs/nfs4proc.c +++ b/fs/nfs/nfs4proc.c @@ -4093,15 +4093,23 @@ nfs4_proc_lock(struct file *filp, int cmd, struct file_lock *request) if (request->fl_start < 0 || request->fl_end < 0) return -EINVAL; - if (IS_GETLK(cmd)) - return nfs4_proc_getlk(state, F_GETLK, request); + if (IS_GETLK(cmd)) { + if (state != NULL) + return nfs4_proc_getlk(state, F_GETLK, request); + return 0; + } if (!(IS_SETLK(cmd) || IS_SETLKW(cmd))) return -EINVAL; - if (request->fl_type == F_UNLCK) - return nfs4_proc_unlck(state, cmd, request); + if (request->fl_type == F_UNLCK) { + if (state != NULL) + return nfs4_proc_unlck(state, cmd, request); + return 0; + } + if (state == NULL) + return -ENOLCK; do { status = nfs4_proc_setlk(state, cmd, request); if ((status != -EAGAIN) || IS_SETLK(cmd)) -- GitLab From bc146d23d1358af43f03793c3ad8c9f16bbcffcb Mon Sep 17 00:00:00 2001 From: Maxime Bizon Date: Thu, 16 Jul 2009 06:32:52 +0000 Subject: [PATCH 0176/1342] ide: fix memory leak when flush command is issued I'm using ide on 2.6.30.1 with xfs filesystem. I noticed a kernel memory leak after writing lots of data, the kmalloc-96 slab cache keeps growing. It seems the struct ide_cmd kmalloced by idedisk_prepare_flush is never kfreed. Commit a09485df9cda49fbde2766c86eb18a9cae585162 ("ide: move request type specific code from ide_end_drive_cmd() to callers (v3)") and f505d49ffd25ed062e76ffd17568d3937fcd338c ("ide: fix barriers support") cause this regression, cmd->rq must now be set for ide_complete_cmd to honor the IDE_TFLAG_DYN flag. Signed-off-by: Maxime Bizon Acked-by: Bartlomiej Zolnierkiewicz Signed-off-by: David S. Miller --- drivers/ide/ide-disk.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/ide/ide-disk.c b/drivers/ide/ide-disk.c index 695181120cd..7f878017b73 100644 --- a/drivers/ide/ide-disk.c +++ b/drivers/ide/ide-disk.c @@ -455,6 +455,7 @@ static void idedisk_prepare_flush(struct request_queue *q, struct request *rq) rq->cmd_type = REQ_TYPE_ATA_TASKFILE; rq->special = cmd; + cmd->rq = rq; } ide_devset_get(multcount, mult_count); -- GitLab From 2fc2111c2729462b99b6e37f39a48917054776f5 Mon Sep 17 00:00:00 2001 From: Michael Buesch Date: Sun, 19 Jul 2009 09:15:19 +0000 Subject: [PATCH 0177/1342] ide-tape: Don't leak kernel stack information Don't leak kernel stack information through uninitialized structure members. Signed-off-by: Michael Buesch Acked-by: Borislav Petkov . Signed-off-by: David S. Miller --- drivers/ide/ide-tape.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/ide/ide-tape.c b/drivers/ide/ide-tape.c index 013dc595fab..bc5fb12b913 100644 --- a/drivers/ide/ide-tape.c +++ b/drivers/ide/ide-tape.c @@ -1064,6 +1064,7 @@ static int idetape_blkdev_ioctl(ide_drive_t *drive, unsigned int cmd, tape->best_dsc_rw_freq = config.dsc_rw_frequency; break; case 0x0350: + memset(&config, 0, sizeof(config)); config.dsc_rw_frequency = (int) tape->best_dsc_rw_freq; config.nr_stages = 1; if (copy_to_user(argp, &config, sizeof(config))) -- GitLab From a947a39d52f5b647a2fd5eca55d39e722a2fa90f Mon Sep 17 00:00:00 2001 From: Mike McCormack Date: Tue, 21 Jul 2009 20:57:56 -0700 Subject: [PATCH 0178/1342] sky2: Avoid races in sky2_down Reset rx chain before trying to drain it. Shut interrupts off last, incase there's something to report. Signed-off-by: Mike McCormack Acked-by: Stephen Hemminger Signed-off-by: David S. Miller --- drivers/net/sky2.c | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index ba768dfa59e..3550c5dcd93 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -1818,12 +1818,6 @@ static int sky2_down(struct net_device *dev) if (netif_msg_ifdown(sky2)) printk(KERN_INFO PFX "%s: disabling interface\n", dev->name); - /* Disable port IRQ */ - imask = sky2_read32(hw, B0_IMSK); - imask &= ~portirq_msk[port]; - sky2_write32(hw, B0_IMSK, imask); - sky2_read32(hw, B0_IMSK); - /* Force flow control off */ sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF); @@ -1863,8 +1857,6 @@ static int sky2_down(struct net_device *dev) sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL), RB_RST_SET); - sky2_rx_stop(sky2); - sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET); sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_SET); @@ -1874,6 +1866,14 @@ static int sky2_down(struct net_device *dev) sky2_write32(hw, STAT_ISR_TIMER_CNT, 0); sky2_read8(hw, STAT_ISR_TIMER_CTRL); + sky2_rx_stop(sky2); + + /* Disable port IRQ */ + imask = sky2_read32(hw, B0_IMSK); + imask &= ~portirq_msk[port]; + sky2_write32(hw, B0_IMSK, imask); + sky2_read32(hw, B0_IMSK); + synchronize_irq(hw->pdev->irq); napi_synchronize(&hw->napi); -- GitLab From 6effa8f6fc786f00e3a23eae605e0f2e8e748faa Mon Sep 17 00:00:00 2001 From: Hidehiro Kawai Date: Wed, 22 Jul 2009 11:56:20 +0900 Subject: [PATCH 0179/1342] x86, mce: Rename incorrect macro name "CONFIG_X86_THRESHOLD" CONFIG_X86_THRESHOLD used in arch/x86/kernel/irqinit.c is always undefined. Rename it to the correct name "CONFIG_X86_MCE_THRESHOLD". Signed-off-by: Hidehiro Kawai Reviewed-by: Hidetoshi Seto Cc: Andi Kleen LKML-Reference: <4A667FD4.3010509@hitachi.com> Signed-off-by: H. Peter Anvin --- arch/x86/kernel/irqinit.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/irqinit.c b/arch/x86/kernel/irqinit.c index 696f0e475c2..92b7703d3d5 100644 --- a/arch/x86/kernel/irqinit.c +++ b/arch/x86/kernel/irqinit.c @@ -187,7 +187,7 @@ static void __init apic_intr_init(void) #ifdef CONFIG_X86_THERMAL_VECTOR alloc_intr_gate(THERMAL_APIC_VECTOR, thermal_interrupt); #endif -#ifdef CONFIG_X86_THRESHOLD +#ifdef CONFIG_X86_MCE_THRESHOLD alloc_intr_gate(THRESHOLD_APIC_VECTOR, threshold_interrupt); #endif #if defined(CONFIG_X86_NEW_MCE) && defined(CONFIG_X86_LOCAL_APIC) -- GitLab From 79452f0a28aa5a40522c487b42a5fc423647ad98 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Wed, 22 Jul 2009 12:51:51 +0200 Subject: [PATCH 0180/1342] ALSA: pcm - Fix regressions with VMware VMware tends to report PCM positions and period updates at utterly wrong timing. This screws up the recent PCM core code that tries to correct the position based on the irq timing. Now, when a backward irq position is detected, skip the update instead of rebasing. (This is almost the old behavior before 2.6.30.) Signed-off-by: Takashi Iwai --- sound/core/pcm_lib.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-) diff --git a/sound/core/pcm_lib.c b/sound/core/pcm_lib.c index 333e4dd2945..3b673e2f991 100644 --- a/sound/core/pcm_lib.c +++ b/sound/core/pcm_lib.c @@ -244,18 +244,27 @@ static int snd_pcm_update_hw_ptr_interrupt(struct snd_pcm_substream *substream) delta = new_hw_ptr - hw_ptr_interrupt; } if (delta < 0) { - delta += runtime->buffer_size; + if (runtime->periods == 1) + delta += runtime->buffer_size; if (delta < 0) { hw_ptr_error(substream, "Unexpected hw_pointer value " "(stream=%i, pos=%ld, intr_ptr=%ld)\n", substream->stream, (long)pos, (long)hw_ptr_interrupt); +#if 1 + /* simply skipping the hwptr update seems more + * robust in some cases, e.g. on VMware with + * inaccurate timer source + */ + return 0; /* skip this update */ +#else /* rebase to interrupt position */ hw_base = new_hw_ptr = hw_ptr_interrupt; /* align hw_base to buffer_size */ hw_base -= hw_base % runtime->buffer_size; delta = 0; +#endif } else { hw_base += runtime->buffer_size; if (hw_base >= runtime->boundary) -- GitLab From 2cf313ee75ddf6220b5d623b749b1bb79458307f Mon Sep 17 00:00:00 2001 From: Alexey Fisher Date: Wed, 22 Jul 2009 14:57:54 +0200 Subject: [PATCH 0181/1342] ALSA: usb-audio - Volume control quirk for QuickCam E 3500 - E3500 report cval->max more than it actually can handel, so if you set 95% capture level it will be silently muted. - Betwen cval->min and cval-max(real) is 2940 control units, but real are only 7 with cval->res = 384. - Alsa can't handel less than 10 controls, so make it more and set cval->res = 192. Signed-off-by: Alexey Fisher Signed-off-by: Takashi Iwai --- sound/usb/usbmixer.c | 25 ++++++++++++++++++++----- 1 file changed, 20 insertions(+), 5 deletions(-) diff --git a/sound/usb/usbmixer.c b/sound/usb/usbmixer.c index 4bd3a7a0edc..ec9cdf98692 100644 --- a/sound/usb/usbmixer.c +++ b/sound/usb/usbmixer.c @@ -990,20 +990,35 @@ static void build_feature_ctl(struct mixer_build *state, unsigned char *desc, break; } - /* quirk for UDA1321/N101 */ - /* note that detection between firmware 2.1.1.7 (N101) and later 2.1.1.21 */ - /* is not very clear from datasheets */ - /* I hope that the min value is -15360 for newer firmware --jk */ + /* volume control quirks */ switch (state->chip->usb_id) { case USB_ID(0x0471, 0x0101): case USB_ID(0x0471, 0x0104): case USB_ID(0x0471, 0x0105): case USB_ID(0x0672, 0x1041): + /* quirk for UDA1321/N101. + * note that detection between firmware 2.1.1.7 (N101) + * and later 2.1.1.21 is not very clear from datasheets. + * I hope that the min value is -15360 for newer firmware --jk + */ if (!strcmp(kctl->id.name, "PCM Playback Volume") && cval->min == -15616) { - snd_printk(KERN_INFO "using volume control quirk for the UDA1321/N101 chip\n"); + snd_printk(KERN_INFO + "set volume quirk for UDA1321/N101 chip\n"); cval->max = -256; } + break; + + case USB_ID(0x046d, 0x09a4): + if (!strcmp(kctl->id.name, "Mic Capture Volume")) { + snd_printk(KERN_INFO + "set volume quirk for QuickCam E3500\n"); + cval->min = 6080; + cval->max = 8768; + cval->res = 192; + } + break; + } snd_printdd(KERN_INFO "[%d] FU [%s] ch = %d, val = %d/%d/%d\n", -- GitLab From 1bec1aed1e7e632b3cc43b6807c2b4dcd1572e28 Mon Sep 17 00:00:00 2001 From: Yan Zheng Date: Wed, 22 Jul 2009 09:59:00 -0400 Subject: [PATCH 0182/1342] Btrfs: fix definition of struct btrfs_extent_inline_ref use __le64 instead of u64 in on-disk structure definition. Signed-off-by: Yan Zheng Signed-off-by: Chris Mason --- fs/btrfs/ctree.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/btrfs/ctree.h b/fs/btrfs/ctree.h index a404ecc53eb..da0763135bf 100644 --- a/fs/btrfs/ctree.h +++ b/fs/btrfs/ctree.h @@ -483,7 +483,7 @@ struct btrfs_shared_data_ref { struct btrfs_extent_inline_ref { u8 type; - u64 offset; + __le64 offset; } __attribute__ ((__packed__)); /* old style backrefs item */ -- GitLab From bf1fb512a58d7aeb41aaa40d6d2d2d29e08e506a Mon Sep 17 00:00:00 2001 From: Yan Zheng Date: Wed, 22 Jul 2009 09:59:00 -0400 Subject: [PATCH 0183/1342] Btrfs: properly update space information after shrinking device. Change 'goto done' to 'break' for the case of all device extents have been freed, so that the code updates space information will be execute. Signed-off-by: Yan Zheng Signed-off-by: Chris Mason --- fs/btrfs/volumes.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/fs/btrfs/volumes.c b/fs/btrfs/volumes.c index 3ab80e9cd76..f057730a72b 100644 --- a/fs/btrfs/volumes.c +++ b/fs/btrfs/volumes.c @@ -2007,7 +2007,7 @@ int btrfs_shrink_device(struct btrfs_device *device, u64 new_size) goto done; if (ret) { ret = 0; - goto done; + break; } l = path->nodes[0]; @@ -2015,7 +2015,7 @@ int btrfs_shrink_device(struct btrfs_device *device, u64 new_size) btrfs_item_key_to_cpu(l, &key, path->slots[0]); if (key.objectid != device->devid) - goto done; + break; dev_extent = btrfs_item_ptr(l, slot, struct btrfs_dev_extent); length = btrfs_dev_extent_length(l, dev_extent); -- GitLab From e457afec60fdbd86b963d36f4a8a9285088c6043 Mon Sep 17 00:00:00 2001 From: Yan Zheng Date: Wed, 22 Jul 2009 09:59:00 -0400 Subject: [PATCH 0184/1342] Btrfs: fix double increment of path->slots[0] in btrfs_next_leaf if 1 is returned by btrfs_search_slot, the path already points to the first item with 'key > searching key'. So increasing path->slots[0] by one is superfluous in that case. Signed-off-by: Yan Zheng Signed-off-by: Chris Mason --- fs/btrfs/ctree.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/fs/btrfs/ctree.c b/fs/btrfs/ctree.c index 60a45f3a4e9..7bb66c65ddf 100644 --- a/fs/btrfs/ctree.c +++ b/fs/btrfs/ctree.c @@ -4146,7 +4146,8 @@ again: * advance the path if there are now more items available. */ if (nritems > 0 && path->slots[0] < nritems - 1) { - path->slots[0]++; + if (ret == 0) + path->slots[0]++; ret = 0; goto done; } -- GitLab From 33c66f430bfa3a033e70470e4c93f967156b696d Mon Sep 17 00:00:00 2001 From: Yan Zheng Date: Wed, 22 Jul 2009 09:59:00 -0400 Subject: [PATCH 0185/1342] Btrfs: fix locking issue in btrfs_find_next_key When walking up the tree, btrfs_find_next_key assumes the upper level tree block is properly locked. This isn't always true even path->keep_locks is 1. This is because btrfs_find_next_key may advance path->slots[] several times instead of only once. When 'path->slots[level] >= btrfs_header_nritems(path->nodes[level])' is found, we can't guarantee the original value of 'path->slots[level]' is 'btrfs_header_nritems(path->nodes[level]) - 1'. If it's not, the tree block at 'level + 1' isn't locked. This patch fixes the issue by explicitly checking the locking state, re-searching the tree if it's not locked. Signed-off-by: Yan Zheng Signed-off-by: Chris Mason --- fs/btrfs/ctree.c | 95 ++++++++++++++++++++++++++++--------------- fs/btrfs/relocation.c | 3 ++ 2 files changed, 65 insertions(+), 33 deletions(-) diff --git a/fs/btrfs/ctree.c b/fs/btrfs/ctree.c index 7bb66c65ddf..fdd423a550d 100644 --- a/fs/btrfs/ctree.c +++ b/fs/btrfs/ctree.c @@ -1701,6 +1701,7 @@ int btrfs_search_slot(struct btrfs_trans_handle *trans, struct btrfs_root struct extent_buffer *b; int slot; int ret; + int err; int level; int lowest_unlock = 1; u8 lowest_level = 0; @@ -1737,8 +1738,6 @@ again: p->locks[level] = 1; if (cow) { - int wret; - /* * if we don't really need to cow this block * then we don't want to set the path blocking, @@ -1749,12 +1748,12 @@ again: btrfs_set_path_blocking(p); - wret = btrfs_cow_block(trans, root, b, - p->nodes[level + 1], - p->slots[level + 1], &b); - if (wret) { + err = btrfs_cow_block(trans, root, b, + p->nodes[level + 1], + p->slots[level + 1], &b); + if (err) { free_extent_buffer(b); - ret = wret; + ret = err; goto done; } } @@ -1793,41 +1792,45 @@ cow_done: ret = bin_search(b, key, level, &slot); if (level != 0) { - if (ret && slot > 0) + int dec = 0; + if (ret && slot > 0) { + dec = 1; slot -= 1; + } p->slots[level] = slot; - ret = setup_nodes_for_search(trans, root, p, b, level, + err = setup_nodes_for_search(trans, root, p, b, level, ins_len); - if (ret == -EAGAIN) + if (err == -EAGAIN) goto again; - else if (ret) + if (err) { + ret = err; goto done; + } b = p->nodes[level]; slot = p->slots[level]; unlock_up(p, level, lowest_unlock); - /* this is only true while dropping a snapshot */ if (level == lowest_level) { - ret = 0; + if (dec) + p->slots[level]++; goto done; } - ret = read_block_for_search(trans, root, p, + err = read_block_for_search(trans, root, p, &b, level, slot, key); - if (ret == -EAGAIN) + if (err == -EAGAIN) goto again; - - if (ret == -EIO) + if (err) { + ret = err; goto done; + } if (!p->skip_locking) { - int lret; - btrfs_clear_path_blocking(p, NULL); - lret = btrfs_try_spin_lock(b); + err = btrfs_try_spin_lock(b); - if (!lret) { + if (!err) { btrfs_set_path_blocking(p); btrfs_tree_lock(b); btrfs_clear_path_blocking(p, b); @@ -1837,16 +1840,14 @@ cow_done: p->slots[level] = slot; if (ins_len > 0 && btrfs_leaf_free_space(root, b) < ins_len) { - int sret; - btrfs_set_path_blocking(p); - sret = split_leaf(trans, root, key, - p, ins_len, ret == 0); + err = split_leaf(trans, root, key, + p, ins_len, ret == 0); btrfs_clear_path_blocking(p, NULL); - BUG_ON(sret > 0); - if (sret) { - ret = sret; + BUG_ON(err > 0); + if (err) { + ret = err; goto done; } } @@ -4042,10 +4043,9 @@ out: * calling this function. */ int btrfs_find_next_key(struct btrfs_root *root, struct btrfs_path *path, - struct btrfs_key *key, int lowest_level, + struct btrfs_key *key, int level, int cache_only, u64 min_trans) { - int level = lowest_level; int slot; struct extent_buffer *c; @@ -4058,11 +4058,40 @@ int btrfs_find_next_key(struct btrfs_root *root, struct btrfs_path *path, c = path->nodes[level]; next: if (slot >= btrfs_header_nritems(c)) { - level++; - if (level == BTRFS_MAX_LEVEL) + int ret; + int orig_lowest; + struct btrfs_key cur_key; + if (level + 1 >= BTRFS_MAX_LEVEL || + !path->nodes[level + 1]) return 1; - continue; + + if (path->locks[level + 1]) { + level++; + continue; + } + + slot = btrfs_header_nritems(c) - 1; + if (level == 0) + btrfs_item_key_to_cpu(c, &cur_key, slot); + else + btrfs_node_key_to_cpu(c, &cur_key, slot); + + orig_lowest = path->lowest_level; + btrfs_release_path(root, path); + path->lowest_level = level; + ret = btrfs_search_slot(NULL, root, &cur_key, path, + 0, 0); + path->lowest_level = orig_lowest; + if (ret < 0) + return ret; + + c = path->nodes[level]; + slot = path->slots[level]; + if (ret == 0) + slot++; + goto next; } + if (level == 0) btrfs_item_key_to_cpu(c, key, slot); else { diff --git a/fs/btrfs/relocation.c b/fs/btrfs/relocation.c index 00839793477..e71264d1c2c 100644 --- a/fs/btrfs/relocation.c +++ b/fs/btrfs/relocation.c @@ -670,6 +670,8 @@ again: err = ret; goto out; } + if (ret > 0 && path2->slots[level] > 0) + path2->slots[level]--; eb = path2->nodes[level]; WARN_ON(btrfs_node_blockptr(eb, path2->slots[level]) != @@ -1609,6 +1611,7 @@ static noinline_for_stack int merge_reloc_root(struct reloc_control *rc, BUG_ON(level == 0); path->lowest_level = level; ret = btrfs_search_slot(NULL, reloc_root, &key, path, 0, 0); + path->lowest_level = 0; if (ret < 0) { btrfs_free_path(path); return ret; -- GitLab From 86de7416600e93835eeacee379aea939b6a0917a Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Wed, 22 Jul 2009 16:02:46 +0200 Subject: [PATCH 0186/1342] ALSA: hda - Use snprintf() to be safer Use snprint() for creating the jack name string instead of sprintf() in patch_sigmatel.c. Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_sigmatel.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/pci/hda/patch_sigmatel.c b/sound/pci/hda/patch_sigmatel.c index da7f9f65c04..512f3b9b9a4 100644 --- a/sound/pci/hda/patch_sigmatel.c +++ b/sound/pci/hda/patch_sigmatel.c @@ -4066,7 +4066,7 @@ static int stac92xx_add_jack(struct hda_codec *codec, jack->nid = nid; jack->type = type; - sprintf(name, "%s at %s %s Jack", + snprintf(name, sizeof(name), "%s at %s %s Jack", snd_hda_get_jack_type(def_conf), snd_hda_get_jack_connectivity(def_conf), snd_hda_get_jack_location(def_conf)); -- GitLab From 4a8c9a62d7f7f058eed4b8a6f2c890a887778093 Mon Sep 17 00:00:00 2001 From: Yan Zheng Date: Wed, 22 Jul 2009 10:07:05 -0400 Subject: [PATCH 0187/1342] Btrfs: make sure all dirty blocks are written at commit time Write dirty block groups may allocate new block, and so may add new delayed back ref. btrfs_run_delayed_refs may make some block groups dirty. commit_cowonly_roots does not handle the recursion properly, and some dirty blocks can be left unwritten at commit time. This patch moves btrfs_run_delayed_refs into the loop that writes dirty block groups, and makes the code not break out of the loop until there are no dirty block groups or delayed back refs. Signed-off-by: Yan Zheng Signed-off-by: Chris Mason --- fs/btrfs/extent-tree.c | 70 +++++++++++++++++++++++++----------------- fs/btrfs/transaction.c | 9 +----- 2 files changed, 42 insertions(+), 37 deletions(-) diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c index a5aca3997d4..62a332d34fd 100644 --- a/fs/btrfs/extent-tree.c +++ b/fs/btrfs/extent-tree.c @@ -2387,13 +2387,29 @@ fail: } +static struct btrfs_block_group_cache * +next_block_group(struct btrfs_root *root, + struct btrfs_block_group_cache *cache) +{ + struct rb_node *node; + spin_lock(&root->fs_info->block_group_cache_lock); + node = rb_next(&cache->cache_node); + btrfs_put_block_group(cache); + if (node) { + cache = rb_entry(node, struct btrfs_block_group_cache, + cache_node); + atomic_inc(&cache->count); + } else + cache = NULL; + spin_unlock(&root->fs_info->block_group_cache_lock); + return cache; +} + int btrfs_write_dirty_block_groups(struct btrfs_trans_handle *trans, struct btrfs_root *root) { - struct btrfs_block_group_cache *cache, *entry; - struct rb_node *n; + struct btrfs_block_group_cache *cache; int err = 0; - int werr = 0; struct btrfs_path *path; u64 last = 0; @@ -2402,39 +2418,35 @@ int btrfs_write_dirty_block_groups(struct btrfs_trans_handle *trans, return -ENOMEM; while (1) { - cache = NULL; - spin_lock(&root->fs_info->block_group_cache_lock); - for (n = rb_first(&root->fs_info->block_group_cache_tree); - n; n = rb_next(n)) { - entry = rb_entry(n, struct btrfs_block_group_cache, - cache_node); - if (entry->dirty) { - cache = entry; - break; - } + if (last == 0) { + err = btrfs_run_delayed_refs(trans, root, + (unsigned long)-1); + BUG_ON(err); } - spin_unlock(&root->fs_info->block_group_cache_lock); - if (!cache) - break; + cache = btrfs_lookup_first_block_group(root->fs_info, last); + while (cache) { + if (cache->dirty) + break; + cache = next_block_group(root, cache); + } + if (!cache) { + if (last == 0) + break; + last = 0; + continue; + } cache->dirty = 0; - last += cache->key.offset; + last = cache->key.objectid + cache->key.offset; - err = write_one_cache_group(trans, root, - path, cache); - /* - * if we fail to write the cache group, we want - * to keep it marked dirty in hopes that a later - * write will work - */ - if (err) { - werr = err; - continue; - } + err = write_one_cache_group(trans, root, path, cache); + BUG_ON(err); + btrfs_put_block_group(cache); } + btrfs_free_path(path); - return werr; + return 0; } int btrfs_extent_readonly(struct btrfs_root *root, u64 bytenr) diff --git a/fs/btrfs/transaction.c b/fs/btrfs/transaction.c index 2dbf1c1f56e..81f7124c305 100644 --- a/fs/btrfs/transaction.c +++ b/fs/btrfs/transaction.c @@ -444,9 +444,6 @@ static int update_cowonly_root(struct btrfs_trans_handle *trans, btrfs_write_dirty_block_groups(trans, root); - ret = btrfs_run_delayed_refs(trans, root, (unsigned long)-1); - BUG_ON(ret); - while (1) { old_root_bytenr = btrfs_root_bytenr(&root->root_item); if (old_root_bytenr == root->node->start) @@ -457,9 +454,8 @@ static int update_cowonly_root(struct btrfs_trans_handle *trans, &root->root_key, &root->root_item); BUG_ON(ret); - btrfs_write_dirty_block_groups(trans, root); - ret = btrfs_run_delayed_refs(trans, root, (unsigned long)-1); + ret = btrfs_write_dirty_block_groups(trans, root); BUG_ON(ret); } free_extent_buffer(root->commit_root); @@ -495,9 +491,6 @@ static noinline int commit_cowonly_roots(struct btrfs_trans_handle *trans, root = list_entry(next, struct btrfs_root, dirty_list); update_cowonly_root(trans, root); - - ret = btrfs_run_delayed_refs(trans, root, (unsigned long)-1); - BUG_ON(ret); } return 0; } -- GitLab From 9ba5f005c994ad28e266a0cd14ef29354be382c9 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Wed, 22 Jul 2009 14:18:35 +0200 Subject: [PATCH 0188/1342] softirq: introduce tasklet_hrtimer infrastructure commit ca109491f (hrtimer: removing all ur callback modes) moved all hrtimer callbacks into hard interrupt context when high resolution timers are active. That breaks code which relied on the assumption that the callback happens in softirq context. Provide a generic infrastructure which combines tasklets and hrtimers together to provide an in-softirq hrtimer experience. Signed-off-by: Peter Zijlstra Cc: torvalds@linux-foundation.org Cc: kaber@trash.net Cc: David Miller LKML-Reference: <1248265724.27058.1366.camel@twins> Signed-off-by: Thomas Gleixner --- include/linux/interrupt.h | 26 ++++++++++++++++ kernel/softirq.c | 64 ++++++++++++++++++++++++++++++++++++++- 2 files changed, 89 insertions(+), 1 deletion(-) diff --git a/include/linux/interrupt.h b/include/linux/interrupt.h index 2721f07e935..fd4c9c63c75 100644 --- a/include/linux/interrupt.h +++ b/include/linux/interrupt.h @@ -14,6 +14,7 @@ #include #include #include +#include #include #include @@ -517,6 +518,31 @@ extern void tasklet_kill_immediate(struct tasklet_struct *t, unsigned int cpu); extern void tasklet_init(struct tasklet_struct *t, void (*func)(unsigned long), unsigned long data); +struct tasklet_hrtimer { + struct hrtimer timer; + struct tasklet_struct tasklet; + enum hrtimer_restart (*function)(struct hrtimer *); +}; + +extern void +tasklet_hrtimer_init(struct tasklet_hrtimer *ttimer, + enum hrtimer_restart (*function)(struct hrtimer *), + clockid_t which_clock, enum hrtimer_mode mode); + +static inline +int tasklet_hrtimer_start(struct tasklet_hrtimer *ttimer, ktime_t time, + const enum hrtimer_mode mode) +{ + return hrtimer_start(&ttimer->timer, time, mode); +} + +static inline +void tasklet_hrtimer_cancel(struct tasklet_hrtimer *ttimer) +{ + hrtimer_cancel(&ttimer->timer); + tasklet_kill(&ttimer->tasklet); +} + /* * Autoprobing for irqs: * diff --git a/kernel/softirq.c b/kernel/softirq.c index 3a94905fa5d..eb5e131a048 100644 --- a/kernel/softirq.c +++ b/kernel/softirq.c @@ -345,7 +345,9 @@ void open_softirq(int nr, void (*action)(struct softirq_action *)) softirq_vec[nr].action = action; } -/* Tasklets */ +/* + * Tasklets + */ struct tasklet_head { struct tasklet_struct *head; @@ -493,6 +495,66 @@ void tasklet_kill(struct tasklet_struct *t) EXPORT_SYMBOL(tasklet_kill); +/* + * tasklet_hrtimer + */ + +/* + * The trampoline is called when the hrtimer expires. If this is + * called from the hrtimer interrupt then we schedule the tasklet as + * the timer callback function expects to run in softirq context. If + * it's called in softirq context anyway (i.e. high resolution timers + * disabled) then the hrtimer callback is called right away. + */ +static enum hrtimer_restart __hrtimer_tasklet_trampoline(struct hrtimer *timer) +{ + struct tasklet_hrtimer *ttimer = + container_of(timer, struct tasklet_hrtimer, timer); + + if (hrtimer_is_hres_active(timer)) { + tasklet_hi_schedule(&ttimer->tasklet); + return HRTIMER_NORESTART; + } + return ttimer->function(timer); +} + +/* + * Helper function which calls the hrtimer callback from + * tasklet/softirq context + */ +static void __tasklet_hrtimer_trampoline(unsigned long data) +{ + struct tasklet_hrtimer *ttimer = (void *)data; + enum hrtimer_restart restart; + + restart = ttimer->function(&ttimer->timer); + if (restart != HRTIMER_NORESTART) + hrtimer_restart(&ttimer->timer); +} + +/** + * tasklet_hrtimer_init - Init a tasklet/hrtimer combo for softirq callbacks + * @ttimer: tasklet_hrtimer which is initialized + * @function: hrtimer callback funtion which gets called from softirq context + * @which_clock: clock id (CLOCK_MONOTONIC/CLOCK_REALTIME) + * @mode: hrtimer mode (HRTIMER_MODE_ABS/HRTIMER_MODE_REL) + */ +void tasklet_hrtimer_init(struct tasklet_hrtimer *ttimer, + enum hrtimer_restart (*function)(struct hrtimer *), + clockid_t which_clock, enum hrtimer_mode mode) +{ + hrtimer_init(&ttimer->timer, which_clock, mode); + ttimer->timer.function = __hrtimer_tasklet_trampoline; + tasklet_init(&ttimer->tasklet, __tasklet_hrtimer_trampoline, + (unsigned long)ttimer); + ttimer->function = function; +} +EXPORT_SYMBOL_GPL(tasklet_hrtimer_init); + +/* + * Remote softirq bits + */ + DEFINE_PER_CPU(struct list_head [NR_SOFTIRQS], softirq_work_list); EXPORT_PER_CPU_SYMBOL(softirq_work_list); -- GitLab From 68110661e86868cd107955ec7c077e1f34519f78 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Wed, 22 Jul 2009 17:05:15 +0200 Subject: [PATCH 0189/1342] ALSA: ctxfi - Fix uninitialized error checks MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Fix a few uninitialized error checks that were introduced recently mistakenlly during the clean-up: sound/pci/ctxfi/ctamixer.c: In function ‘get_amixer_rsc’: sound/pci/ctxfi/ctamixer.c:261: warning: ‘err’ may be used uninitialized in this function sound/pci/ctxfi/ctamixer.c: In function ‘get_sum_rsc’: sound/pci/ctxfi/ctamixer.c:415: warning: ‘err’ may be used uninitialized in this function sound/pci/ctxfi/ctsrc.c: In function ‘get_srcimp_rsc’: sound/pci/ctxfi/ctsrc.c:742: warning: ‘err’ may be used uninitialized in this function Signed-off-by: Takashi Iwai --- sound/pci/ctxfi/ctamixer.c | 14 ++++++-------- sound/pci/ctxfi/ctsrc.c | 7 +++---- 2 files changed, 9 insertions(+), 12 deletions(-) diff --git a/sound/pci/ctxfi/ctamixer.c b/sound/pci/ctxfi/ctamixer.c index a1db51b3ead..a7f4a671f7b 100644 --- a/sound/pci/ctxfi/ctamixer.c +++ b/sound/pci/ctxfi/ctamixer.c @@ -242,13 +242,12 @@ static int get_amixer_rsc(struct amixer_mgr *mgr, /* Allocate mem for amixer resource */ amixer = kzalloc(sizeof(*amixer), GFP_KERNEL); - if (NULL == amixer) { - err = -ENOMEM; - return err; - } + if (!amixer) + return -ENOMEM; /* Check whether there are sufficient * amixer resources to meet request. */ + err = 0; spin_lock_irqsave(&mgr->mgr_lock, flags); for (i = 0; i < desc->msr; i++) { err = mgr_get_resource(&mgr->mgr, 1, &idx); @@ -397,12 +396,11 @@ static int get_sum_rsc(struct sum_mgr *mgr, /* Allocate mem for sum resource */ sum = kzalloc(sizeof(*sum), GFP_KERNEL); - if (NULL == sum) { - err = -ENOMEM; - return err; - } + if (!sum) + return -ENOMEM; /* Check whether there are sufficient sum resources to meet request. */ + err = 0; spin_lock_irqsave(&mgr->mgr_lock, flags); for (i = 0; i < desc->msr; i++) { err = mgr_get_resource(&mgr->mgr, 1, &idx); diff --git a/sound/pci/ctxfi/ctsrc.c b/sound/pci/ctxfi/ctsrc.c index e1c145d8b70..df43a5cd393 100644 --- a/sound/pci/ctxfi/ctsrc.c +++ b/sound/pci/ctxfi/ctsrc.c @@ -724,12 +724,11 @@ static int get_srcimp_rsc(struct srcimp_mgr *mgr, /* Allocate mem for SRCIMP resource */ srcimp = kzalloc(sizeof(*srcimp), GFP_KERNEL); - if (NULL == srcimp) { - err = -ENOMEM; - return err; - } + if (!srcimp) + return -ENOMEM; /* Check whether there are sufficient SRCIMP resources. */ + err = 0; spin_lock_irqsave(&mgr->mgr_lock, flags); for (i = 0; i < desc->msr; i++) { err = mgr_get_resource(&mgr->mgr, 1, &idx); -- GitLab From 3730793d457fed79a6d49bae72996d458c8e4f2d Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Wed, 22 Jul 2009 08:49:22 -0700 Subject: [PATCH 0190/1342] fbmon: work around compiler bug in gcc-2.4.2 There's some odd bug in gcc-4.2 where it miscompiles a simple loop whent he loop counter is of type 'unsigned char' and it should count to 128. The compiler will incorrectly decide that a trivial loop like this: unsigned char i, ... for (i = 0; i < 128; i++) { .. is endless, and will compile it to a single instruction that just branches to itself. This was triggered by the addition of '-fno-strict-overflow', and we could play games with compiler versions and go back to '-fwrapv' instead, but the trivial way to avoid it is to just make the loop induction variable be an 'int' instead. Thanks to Krzysztof Oledzki for reporting and testing and to Troy Moure for digging through assembler differences and finding it. Reported-and-tested-by: Krzysztof Oledzki Found-by: Troy Moure Gcc-bug-acked-by: Ian Lance Taylor Cc: stable@kernel.org Signed-off-by: Linus Torvalds --- drivers/video/fbmon.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/video/fbmon.c b/drivers/video/fbmon.c index 5c1a2c01778..9ae9cd32bd0 100644 --- a/drivers/video/fbmon.c +++ b/drivers/video/fbmon.c @@ -256,8 +256,8 @@ static void fix_edid(unsigned char *edid, int fix) static int edid_checksum(unsigned char *edid) { - unsigned char i, csum = 0, all_null = 0; - int err = 0, fix = check_edid(edid); + unsigned char csum = 0, all_null = 0; + int i, err = 0, fix = check_edid(edid); if (fix) fix_edid(edid, fix); -- GitLab From 9b7019ae6a542a801a80df6694c66e240e2c3e39 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Wed, 22 Jul 2009 16:31:36 +0200 Subject: [PATCH 0191/1342] perf_counter: Remove unused variables Fix a gcc unused variables warning. Signed-off-by: Peter Zijlstra --- arch/x86/kernel/cpu/perf_counter.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/arch/x86/kernel/cpu/perf_counter.c b/arch/x86/kernel/cpu/perf_counter.c index 7e346d4bc0f..a7aa8f90095 100644 --- a/arch/x86/kernel/cpu/perf_counter.c +++ b/arch/x86/kernel/cpu/perf_counter.c @@ -1570,8 +1570,6 @@ static struct x86_pmu amd_pmu = { static int p6_pmu_init(void) { - int high, low; - switch (boot_cpu_data.x86_model) { case 1: case 3: /* Pentium Pro */ -- GitLab From c9f73a3dd27e03411f18a58c0814d51392d2b17a Mon Sep 17 00:00:00 2001 From: Arjan van de Ven Date: Tue, 21 Jul 2009 00:55:05 -0700 Subject: [PATCH 0192/1342] perf: Fix stack data leak the "reserved" field was not initialized to zero, resulting in 4 bytes of stack data leaking to userspace.... Signed-off-by: Arjan van de Ven Signed-off-by: Peter Zijlstra --- kernel/perf_counter.c | 1 + 1 file changed, 1 insertion(+) diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index 5c6fae4f43d..ff854fd89a8 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -2666,6 +2666,7 @@ static void perf_counter_output(struct perf_counter *counter, int nmi, header.size += sizeof(cpu_entry); cpu_entry.cpu = raw_smp_processor_id(); + cpu_entry.reserved = 0; } if (sample_type & PERF_SAMPLE_PERIOD) -- GitLab From 573402db02746179b3f95f83a11a787501f52d0a Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Wed, 22 Jul 2009 11:13:50 +0200 Subject: [PATCH 0193/1342] perf_counter: Plug more stack leaks Per example of Arjan's patch, I went through and found a few more. Signed-off-by: Peter Zijlstra --- kernel/perf_counter.c | 23 +++++++++++++++++++++-- 1 file changed, 21 insertions(+), 2 deletions(-) diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index ff854fd89a8..e1d6a3aa133 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -2897,8 +2897,11 @@ void perf_counter_fork(struct task_struct *task) .event = { .header = { .type = PERF_EVENT_FORK, + .misc = 0, .size = sizeof(fork_event.event), }, + /* .pid */ + /* .ppid */ }, }; @@ -3008,8 +3011,16 @@ void perf_counter_comm(struct task_struct *task) comm_event = (struct perf_comm_event){ .task = task, + /* .comm */ + /* .comm_size */ .event = { - .header = { .type = PERF_EVENT_COMM, }, + .header = { + .type = PERF_EVENT_COMM, + .misc = 0, + /* .size */ + }, + /* .pid */ + /* .tid */ }, }; @@ -3160,8 +3171,16 @@ void __perf_counter_mmap(struct vm_area_struct *vma) mmap_event = (struct perf_mmap_event){ .vma = vma, + /* .file_name */ + /* .file_size */ .event = { - .header = { .type = PERF_EVENT_MMAP, }, + .header = { + .type = PERF_EVENT_MMAP, + .misc = 0, + /* .size */ + }, + /* .pid */ + /* .tid */ .start = vma->vm_start, .len = vma->vm_end - vma->vm_start, .pgoff = vma->vm_pgoff, -- GitLab From 7f453c24b95a085fc7bd35d53b33abc4dc5a048b Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Tue, 21 Jul 2009 13:19:40 +0200 Subject: [PATCH 0194/1342] perf_counter: PERF_SAMPLE_ID and inherited counters Anton noted that for inherited counters the counter-id as provided by PERF_SAMPLE_ID isn't mappable to the id found through PERF_RECORD_ID because each inherited counter gets its own id. His suggestion was to always return the parent counter id, since that is the primary counter id as exposed. However, these inherited counters have a unique identifier so that events like PERF_EVENT_PERIOD and PERF_EVENT_THROTTLE can be specific about which counter gets modified, which is important when trying to normalize the sample streams. This patch removes PERF_EVENT_PERIOD in favour of PERF_SAMPLE_PERIOD, which is more useful anyway, since changing periods became a lot more common than initially thought -- rendering PERF_EVENT_PERIOD the less useful solution (also, PERF_SAMPLE_PERIOD reports the more accurate value, since it reports the value used to trigger the overflow, whereas PERF_EVENT_PERIOD simply reports the requested period changed, which might only take effect on the next cycle). This still leaves us PERF_EVENT_THROTTLE to consider, but since that _should_ be a rare occurrence, and linking it to a primary id is the most useful bit to diagnose the problem, we introduce a PERF_SAMPLE_STREAM_ID, for those few cases where the full reconstruction is important. [Does change the ABI a little, but I see no other way out] Suggested-by: Anton Blanchard Signed-off-by: Peter Zijlstra LKML-Reference: <1248095846.15751.8781.camel@twins> --- include/linux/perf_counter.h | 15 ++---- kernel/perf_counter.c | 92 ++++++++++++----------------------- tools/perf/builtin-annotate.c | 24 --------- tools/perf/builtin-report.c | 24 --------- 4 files changed, 35 insertions(+), 120 deletions(-) diff --git a/include/linux/perf_counter.h b/include/linux/perf_counter.h index 5e970c7d3fd..bd15d7a5f5c 100644 --- a/include/linux/perf_counter.h +++ b/include/linux/perf_counter.h @@ -120,8 +120,9 @@ enum perf_counter_sample_format { PERF_SAMPLE_ID = 1U << 6, PERF_SAMPLE_CPU = 1U << 7, PERF_SAMPLE_PERIOD = 1U << 8, + PERF_SAMPLE_STREAM_ID = 1U << 9, - PERF_SAMPLE_MAX = 1U << 9, /* non-ABI */ + PERF_SAMPLE_MAX = 1U << 10, /* non-ABI */ }; /* @@ -312,16 +313,7 @@ enum perf_event_type { * struct perf_event_header header; * u64 time; * u64 id; - * u64 sample_period; - * }; - */ - PERF_EVENT_PERIOD = 4, - - /* - * struct { - * struct perf_event_header header; - * u64 time; - * u64 id; + * u64 stream_id; * }; */ PERF_EVENT_THROTTLE = 5, @@ -356,6 +348,7 @@ enum perf_event_type { * { u64 time; } && PERF_SAMPLE_TIME * { u64 addr; } && PERF_SAMPLE_ADDR * { u64 id; } && PERF_SAMPLE_ID + * { u64 stream_id;} && PERF_SAMPLE_STREAM_ID * { u32 cpu, res; } && PERF_SAMPLE_CPU * { u64 period; } && PERF_SAMPLE_PERIOD * diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index e1d6a3aa133..7530588fa5c 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -154,6 +154,20 @@ static void unclone_ctx(struct perf_counter_context *ctx) } } +/* + * If we inherit counters we want to return the parent counter id + * to userspace. + */ +static u64 primary_counter_id(struct perf_counter *counter) +{ + u64 id = counter->id; + + if (counter->parent) + id = counter->parent->id; + + return id; +} + /* * Get the perf_counter_context for a task and lock it. * This has to cope with with the fact that until it is locked, @@ -1296,7 +1310,6 @@ static void perf_counter_cpu_sched_in(struct perf_cpu_context *cpuctx, int cpu) #define MAX_INTERRUPTS (~0ULL) static void perf_log_throttle(struct perf_counter *counter, int enable); -static void perf_log_period(struct perf_counter *counter, u64 period); static void perf_adjust_period(struct perf_counter *counter, u64 events) { @@ -1315,8 +1328,6 @@ static void perf_adjust_period(struct perf_counter *counter, u64 events) if (!sample_period) sample_period = 1; - perf_log_period(counter, sample_period); - hwc->sample_period = sample_period; } @@ -1705,7 +1716,7 @@ perf_read_hw(struct perf_counter *counter, char __user *buf, size_t count) values[n++] = counter->total_time_running + atomic64_read(&counter->child_total_time_running); if (counter->attr.read_format & PERF_FORMAT_ID) - values[n++] = counter->id; + values[n++] = primary_counter_id(counter); mutex_unlock(&counter->child_mutex); if (count < n * sizeof(u64)) @@ -1812,8 +1823,6 @@ static int perf_counter_period(struct perf_counter *counter, u64 __user *arg) counter->attr.sample_freq = value; } else { - perf_log_period(counter, value); - counter->attr.sample_period = value; counter->hw.sample_period = value; } @@ -2662,6 +2671,9 @@ static void perf_counter_output(struct perf_counter *counter, int nmi, if (sample_type & PERF_SAMPLE_ID) header.size += sizeof(u64); + if (sample_type & PERF_SAMPLE_STREAM_ID) + header.size += sizeof(u64); + if (sample_type & PERF_SAMPLE_CPU) { header.size += sizeof(cpu_entry); @@ -2705,7 +2717,13 @@ static void perf_counter_output(struct perf_counter *counter, int nmi, if (sample_type & PERF_SAMPLE_ADDR) perf_output_put(&handle, data->addr); - if (sample_type & PERF_SAMPLE_ID) + if (sample_type & PERF_SAMPLE_ID) { + u64 id = primary_counter_id(counter); + + perf_output_put(&handle, id); + } + + if (sample_type & PERF_SAMPLE_STREAM_ID) perf_output_put(&handle, counter->id); if (sample_type & PERF_SAMPLE_CPU) @@ -2728,7 +2746,7 @@ static void perf_counter_output(struct perf_counter *counter, int nmi, if (sub != counter) sub->pmu->read(sub); - group_entry.id = sub->id; + group_entry.id = primary_counter_id(sub); group_entry.counter = atomic64_read(&sub->count); perf_output_put(&handle, group_entry); @@ -2788,15 +2806,8 @@ perf_counter_read_event(struct perf_counter *counter, } if (counter->attr.read_format & PERF_FORMAT_ID) { - u64 id; - event.header.size += sizeof(u64); - if (counter->parent) - id = counter->parent->id; - else - id = counter->id; - - event.format[i++] = id; + event.format[i++] = primary_counter_id(counter); } ret = perf_output_begin(&handle, counter, event.header.size, 0, 0); @@ -3190,49 +3201,6 @@ void __perf_counter_mmap(struct vm_area_struct *vma) perf_counter_mmap_event(&mmap_event); } -/* - * Log sample_period changes so that analyzing tools can re-normalize the - * event flow. - */ - -struct freq_event { - struct perf_event_header header; - u64 time; - u64 id; - u64 period; -}; - -static void perf_log_period(struct perf_counter *counter, u64 period) -{ - struct perf_output_handle handle; - struct freq_event event; - int ret; - - if (counter->hw.sample_period == period) - return; - - if (counter->attr.sample_type & PERF_SAMPLE_PERIOD) - return; - - event = (struct freq_event) { - .header = { - .type = PERF_EVENT_PERIOD, - .misc = 0, - .size = sizeof(event), - }, - .time = sched_clock(), - .id = counter->id, - .period = period, - }; - - ret = perf_output_begin(&handle, counter, sizeof(event), 1, 0); - if (ret) - return; - - perf_output_put(&handle, event); - perf_output_end(&handle); -} - /* * IRQ throttle logging */ @@ -3246,14 +3214,16 @@ static void perf_log_throttle(struct perf_counter *counter, int enable) struct perf_event_header header; u64 time; u64 id; + u64 stream_id; } throttle_event = { .header = { .type = PERF_EVENT_THROTTLE + 1, .misc = 0, .size = sizeof(throttle_event), }, - .time = sched_clock(), - .id = counter->id, + .time = sched_clock(), + .id = primary_counter_id(counter), + .stream_id = counter->id, }; ret = perf_output_begin(&handle, counter, sizeof(throttle_event), 1, 0); diff --git a/tools/perf/builtin-annotate.c b/tools/perf/builtin-annotate.c index 5f9eefecc57..1dba568e194 100644 --- a/tools/perf/builtin-annotate.c +++ b/tools/perf/builtin-annotate.c @@ -74,20 +74,12 @@ struct fork_event { u32 pid, ppid; }; -struct period_event { - struct perf_event_header header; - u64 time; - u64 id; - u64 sample_period; -}; - typedef union event_union { struct perf_event_header header; struct ip_event ip; struct mmap_event mmap; struct comm_event comm; struct fork_event fork; - struct period_event period; } event_t; @@ -997,19 +989,6 @@ process_fork_event(event_t *event, unsigned long offset, unsigned long head) return 0; } -static int -process_period_event(event_t *event, unsigned long offset, unsigned long head) -{ - dprintf("%p [%p]: PERF_EVENT_PERIOD: time:%Ld, id:%Ld: period:%Ld\n", - (void *)(offset + head), - (void *)(long)(event->header.size), - event->period.time, - event->period.id, - event->period.sample_period); - - return 0; -} - static int process_event(event_t *event, unsigned long offset, unsigned long head) { @@ -1025,9 +1004,6 @@ process_event(event_t *event, unsigned long offset, unsigned long head) case PERF_EVENT_FORK: return process_fork_event(event, offset, head); - - case PERF_EVENT_PERIOD: - return process_period_event(event, offset, head); /* * We dont process them right now but they are fine: */ diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c index a118bc77286..b20a4b6e31b 100644 --- a/tools/perf/builtin-report.c +++ b/tools/perf/builtin-report.c @@ -101,13 +101,6 @@ struct fork_event { u32 pid, ppid; }; -struct period_event { - struct perf_event_header header; - u64 time; - u64 id; - u64 sample_period; -}; - struct lost_event { struct perf_event_header header; u64 id; @@ -127,7 +120,6 @@ typedef union event_union { struct mmap_event mmap; struct comm_event comm; struct fork_event fork; - struct period_event period; struct lost_event lost; struct read_event read; } event_t; @@ -1635,19 +1627,6 @@ process_fork_event(event_t *event, unsigned long offset, unsigned long head) return 0; } -static int -process_period_event(event_t *event, unsigned long offset, unsigned long head) -{ - dprintf("%p [%p]: PERF_EVENT_PERIOD: time:%Ld, id:%Ld: period:%Ld\n", - (void *)(offset + head), - (void *)(long)(event->header.size), - event->period.time, - event->period.id, - event->period.sample_period); - - return 0; -} - static int process_lost_event(event_t *event, unsigned long offset, unsigned long head) { @@ -1729,9 +1708,6 @@ process_event(event_t *event, unsigned long offset, unsigned long head) case PERF_EVENT_FORK: return process_fork_event(event, offset, head); - case PERF_EVENT_PERIOD: - return process_period_event(event, offset, head); - case PERF_EVENT_LOST: return process_lost_event(event, offset, head); -- GitLab From a0541234f89c93f313961ce7b28676e11488a5f0 Mon Sep 17 00:00:00 2001 From: Anton Blanchard Date: Wed, 22 Jul 2009 23:04:12 +1000 Subject: [PATCH 0195/1342] perf_counter: Improve perf stat and perf record option parsing perf stat and perf record currently look for all options on the command line. This can lead to some confusion: # perf stat ls -l Error: unknown switch `l' While we can work around this by adding '--' before the command, the git option parsing code can stop at the first non option: # perf stat ls -l Performance counter stats for 'ls -l': .... Signed-off-by: Anton Blanchard Signed-off-by: Peter Zijlstra LKML-Reference: <20090722130412.GD9029@kryten> --- tools/perf/builtin-record.c | 3 ++- tools/perf/builtin-stat.c | 3 ++- 2 files changed, 4 insertions(+), 2 deletions(-) diff --git a/tools/perf/builtin-record.c b/tools/perf/builtin-record.c index 68a9be0d151..6da09928130 100644 --- a/tools/perf/builtin-record.c +++ b/tools/perf/builtin-record.c @@ -664,7 +664,8 @@ int cmd_record(int argc, const char **argv, const char *prefix __used) { int counter; - argc = parse_options(argc, argv, options, record_usage, 0); + argc = parse_options(argc, argv, options, record_usage, + PARSE_OPT_STOP_AT_NON_OPTION); if (!argc && target_pid == -1 && !system_wide) usage_with_options(record_usage, options); diff --git a/tools/perf/builtin-stat.c b/tools/perf/builtin-stat.c index 27921a8ce1a..f9510eeeb6c 100644 --- a/tools/perf/builtin-stat.c +++ b/tools/perf/builtin-stat.c @@ -511,7 +511,8 @@ int cmd_stat(int argc, const char **argv, const char *prefix __used) { int status; - argc = parse_options(argc, argv, options, stat_usage, 0); + argc = parse_options(argc, argv, options, stat_usage, + PARSE_OPT_STOP_AT_NON_OPTION); if (!argc) usage_with_options(stat_usage, options); if (run_count <= 0 || run_count > MAX_RUN) -- GitLab From 966ee4d6b887c14159043ac80b8c3661d2bbe5e2 Mon Sep 17 00:00:00 2001 From: Anton Blanchard Date: Wed, 22 Jul 2009 23:05:46 +1000 Subject: [PATCH 0196/1342] perf_counter: Fix throttle/unthrottle event logging Right now we only print PERF_EVENT_THROTTLE + 1 (ie PERF_EVENT_UNTHROTTLE). Fix this to print both a throttle and unthrottle event. Signed-off-by: Anton Blanchard Signed-off-by: Peter Zijlstra LKML-Reference: <20090722130546.GE9029@kryten> --- kernel/perf_counter.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index 7530588fa5c..787d4daef18 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -3217,7 +3217,7 @@ static void perf_log_throttle(struct perf_counter *counter, int enable) u64 stream_id; } throttle_event = { .header = { - .type = PERF_EVENT_THROTTLE + 1, + .type = PERF_EVENT_THROTTLE, .misc = 0, .size = sizeof(throttle_event), }, @@ -3226,6 +3226,9 @@ static void perf_log_throttle(struct perf_counter *counter, int enable) .stream_id = counter->id, }; + if (enable) + throttle_event.header.type = PERF_EVENT_UNTHROTTLE; + ret = perf_output_begin(&handle, counter, sizeof(throttle_event), 1, 0); if (ret) return; -- GitLab From dfe5a50461db90fab901cb697eff0d3d2e9fd229 Mon Sep 17 00:00:00 2001 From: Arjan van de Ven Date: Mon, 20 Jul 2009 22:54:26 -0700 Subject: [PATCH 0197/1342] perf: avoid structure size confusion by using a fixed size for some reason, this structure gets compiled as 36 bytes in some files (the ones that alloacte it) but 40 bytes in others (the ones that use it). The cause is an off_t type that gets a different size in different compilation units for some yet-to-be-explained reason. But the effect is disasterous; the size/offset members of the struct are at different offsets, and result in mostly complete garbage. The parser in perf is so robust that this all gets hidden, and after skipping an certain amount of samples, it recovers.... so this bug is not normally noticed. .... except when you want every sample to be exact. Fix this by just using an explicitly sized type. Signed-off-by: Arjan van de Ven Signed-off-by: Peter Zijlstra LKML-Reference: <4A655917.9080504@linux.intel.com> --- tools/perf/util/header.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/tools/perf/util/header.h b/tools/perf/util/header.h index b5ef53ad4c7..bf280449fcf 100644 --- a/tools/perf/util/header.h +++ b/tools/perf/util/header.h @@ -16,7 +16,7 @@ struct perf_header { int frozen; int attrs, size; struct perf_header_attr **attr; - off_t attr_offset; + s64 attr_offset; u64 data_offset; u64 data_size; }; -- GitLab From 28ac909b49a155856c957d080f8a796b3c1d1f3e Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Mon, 20 Jul 2009 14:14:12 -0300 Subject: [PATCH 0198/1342] perf symbol: C++ demangling MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit [acme@doppio ~]$ perf report -s comm,dso,symbol -C firefox -d /usr/lib64/xulrunner-1.9.1/libxul.so | grep :: | head 2.21% [.] nsDeque::Push(void*) 1.78% [.] GraphWalker::DoWalk(nsDeque&) 1.30% [.] GCGraphBuilder::AddNode(void*, nsCycleCollectionParticipant*) 1.27% [.] XPCWrappedNative::CallMethod(XPCCallContext&, XPCWrappedNative::CallMode) 1.18% [.] imgContainer::DrawFrameTo(gfxIImageFrame*, gfxIImageFrame*, nsRect&) 1.13% [.] nsDeque::PopFront() 1.11% [.] nsGlobalWindow::RunTimeout(nsTimeout*) 0.97% [.] nsXPConnect::Traverse(void*, nsCycleCollectionTraversalCallback&) 0.95% [.] nsJSEventListener::cycleCollection::Traverse(void*, nsCycleCollectionTraversalCallback&) 0.95% [.] nsCOMPtr_base::~nsCOMPtr_base() [acme@doppio ~]$ Cc: Pekka Enberg Cc: Vegard Nossum Cc: Paul Mackerras Cc: Frédéric Weisbecker Suggested-by: Clark Williams Signed-off-by: Arnaldo Carvalho de Melo Signed-off-by: Peter Zijlstra LKML-Reference: <20090720171412.GB10410@ghostprotocols.net> --- tools/perf/Makefile | 2 +- tools/perf/util/symbol.c | 21 +++++++++++++++++++-- 2 files changed, 20 insertions(+), 3 deletions(-) diff --git a/tools/perf/Makefile b/tools/perf/Makefile index 7822b3d6bac..a5e9b876ca0 100644 --- a/tools/perf/Makefile +++ b/tools/perf/Makefile @@ -345,7 +345,7 @@ BUILTIN_OBJS += builtin-stat.o BUILTIN_OBJS += builtin-top.o PERFLIBS = $(LIB_FILE) -EXTLIBS = +EXTLIBS = -lbfd # # Platform specific tweaks diff --git a/tools/perf/util/symbol.c b/tools/perf/util/symbol.c index f40266b4845..98aee922acc 100644 --- a/tools/perf/util/symbol.c +++ b/tools/perf/util/symbol.c @@ -6,9 +6,15 @@ #include #include #include +#include const char *sym_hist_filter; +#ifndef DMGL_PARAMS +#define DMGL_PARAMS (1 << 0) /* Include function args */ +#define DMGL_ANSI (1 << 1) /* Include const, volatile, etc */ +#endif + static struct symbol *symbol__new(u64 start, u64 len, const char *name, unsigned int priv_size, u64 obj_start, int verbose) @@ -571,6 +577,8 @@ static int dso__load_sym(struct dso *self, int fd, const char *name, NULL) != NULL); elf_symtab__for_each_symbol(syms, nr_syms, index, sym) { struct symbol *f; + const char *name; + char *demangled; u64 obj_start; struct section *section = NULL; int is_label = elf_sym__is_label(&sym); @@ -609,10 +617,19 @@ static int dso__load_sym(struct dso *self, int fd, const char *name, goto out_elf_end; } } + /* + * We need to figure out if the object was created from C++ sources + * DWARF DW_compile_unit has this, but we don't always have access + * to it... + */ + name = elf_sym__name(&sym, symstrs); + demangled = bfd_demangle(NULL, name, DMGL_PARAMS | DMGL_ANSI); + if (demangled != NULL) + name = demangled; - f = symbol__new(sym.st_value, sym.st_size, - elf_sym__name(&sym, symstrs), + f = symbol__new(sym.st_value, sym.st_size, name, self->sym_priv_size, obj_start, verbose); + free(demangled); if (!f) goto out_elf_end; -- GitLab From f6bdafef2ab911f03321fa83d8da1df99878009e Mon Sep 17 00:00:00 2001 From: Jason Baron Date: Tue, 21 Jul 2009 12:20:22 -0400 Subject: [PATCH 0199/1342] perf_counter: Add tracepoint support to perf list, perf stat Add support to 'perf list' and 'perf stat' for kernel tracepoints. The implementation creates a 'for_each_subsystem' and 'for_each_event' for easy iteration over the tracepoints. Signed-off-by: Jason Baron Signed-off-by: Peter Zijlstra LKML-Reference: <426129bf9fcc8ee63bb094cf736e7316a7dcd77a.1248190728.git.jbaron@redhat.com> --- tools/perf/util/parse-events.c | 175 ++++++++++++++++++++++++++++++++- tools/perf/util/util.h | 2 + 2 files changed, 176 insertions(+), 1 deletion(-) diff --git a/tools/perf/util/parse-events.c b/tools/perf/util/parse-events.c index d18c98edd00..5a3cd3a34af 100644 --- a/tools/perf/util/parse-events.c +++ b/tools/perf/util/parse-events.c @@ -12,6 +12,8 @@ int nr_counters; struct perf_counter_attr attrs[MAX_COUNTERS]; +static char default_debugfs_path[] = "/sys/kernel/debug/tracing/events"; + struct event_symbol { u8 type; u64 config; @@ -110,6 +112,88 @@ static unsigned long hw_cache_stat[C(MAX)] = { [C(BPU)] = (CACHE_READ), }; +#define for_each_subsystem(sys_dir, sys_dirent, sys_next, file, st) \ + while (!readdir_r(sys_dir, &sys_dirent, &sys_next) && sys_next) \ + if (snprintf(file, MAXPATHLEN, "%s/%s", default_debugfs_path, \ + sys_dirent.d_name) && \ + (!stat(file, &st)) && (S_ISDIR(st.st_mode)) && \ + (strcmp(sys_dirent.d_name, ".")) && \ + (strcmp(sys_dirent.d_name, ".."))) + +#define for_each_event(sys_dirent, evt_dir, evt_dirent, evt_next, file, st) \ + while (!readdir_r(evt_dir, &evt_dirent, &evt_next) && evt_next) \ + if (snprintf(file, MAXPATHLEN, "%s/%s/%s", default_debugfs_path, \ + sys_dirent.d_name, evt_dirent.d_name) && \ + (!stat(file, &st)) && (S_ISDIR(st.st_mode)) && \ + (strcmp(evt_dirent.d_name, ".")) && \ + (strcmp(evt_dirent.d_name, ".."))) + +#define MAX_EVENT_LENGTH 30 + +static int valid_debugfs_mount(void) +{ + struct statfs st_fs; + + if (statfs(default_debugfs_path, &st_fs) < 0) + return -ENOENT; + else if (st_fs.f_type != (long) DEBUGFS_MAGIC) + return -ENOENT; + return 0; +} + +static char *tracepoint_id_to_name(u64 config) +{ + static char tracepoint_name[2 * MAX_EVENT_LENGTH]; + DIR *sys_dir, *evt_dir; + struct dirent *sys_next, *evt_next, sys_dirent, evt_dirent; + struct stat st; + char id_buf[4]; + int fd; + u64 id; + char evt_path[MAXPATHLEN]; + + if (valid_debugfs_mount()) + return "unkown"; + + sys_dir = opendir(default_debugfs_path); + if (!sys_dir) + goto cleanup; + + for_each_subsystem(sys_dir, sys_dirent, sys_next, evt_path, st) { + evt_dir = opendir(evt_path); + if (!evt_dir) + goto cleanup; + for_each_event(sys_dirent, evt_dir, evt_dirent, evt_next, + evt_path, st) { + snprintf(evt_path, MAXPATHLEN, "%s/%s/%s/id", + default_debugfs_path, sys_dirent.d_name, + evt_dirent.d_name); + fd = open(evt_path, O_RDONLY); + if (fd < 0) + continue; + if (read(fd, id_buf, sizeof(id_buf)) < 0) { + close(fd); + continue; + } + close(fd); + id = atoll(id_buf); + if (id == config) { + closedir(evt_dir); + closedir(sys_dir); + snprintf(tracepoint_name, 2 * MAX_EVENT_LENGTH, + "%s:%s", sys_dirent.d_name, + evt_dirent.d_name); + return tracepoint_name; + } + } + closedir(evt_dir); + } + +cleanup: + closedir(sys_dir); + return "unkown"; +} + static int is_cache_op_valid(u8 cache_type, u8 cache_op) { if (hw_cache_stat[cache_type] & COP(cache_op)) @@ -177,6 +261,9 @@ char *event_name(int counter) return sw_event_names[config]; return "unknown-software"; + case PERF_TYPE_TRACEPOINT: + return tracepoint_id_to_name(config); + default: break; } @@ -265,6 +352,53 @@ parse_generic_hw_event(const char **str, struct perf_counter_attr *attr) return 1; } +static int parse_tracepoint_event(const char **strp, + struct perf_counter_attr *attr) +{ + const char *evt_name; + char sys_name[MAX_EVENT_LENGTH]; + char id_buf[4]; + int fd; + unsigned int sys_length, evt_length; + u64 id; + char evt_path[MAXPATHLEN]; + + if (valid_debugfs_mount()) + return 0; + + evt_name = strchr(*strp, ':'); + if (!evt_name) + return 0; + + sys_length = evt_name - *strp; + if (sys_length >= MAX_EVENT_LENGTH) + return 0; + + strncpy(sys_name, *strp, sys_length); + sys_name[sys_length] = '\0'; + evt_name = evt_name + 1; + evt_length = strlen(evt_name); + if (evt_length >= MAX_EVENT_LENGTH) + return 0; + + snprintf(evt_path, MAXPATHLEN, "%s/%s/%s/id", default_debugfs_path, + sys_name, evt_name); + fd = open(evt_path, O_RDONLY); + if (fd < 0) + return 0; + + if (read(fd, id_buf, sizeof(id_buf)) < 0) { + close(fd); + return 0; + } + close(fd); + id = atoll(id_buf); + attr->config = id; + attr->type = PERF_TYPE_TRACEPOINT; + *strp = evt_name + evt_length; + return 1; +} + static int check_events(const char *str, unsigned int i) { int n; @@ -374,7 +508,8 @@ parse_event_modifier(const char **strp, struct perf_counter_attr *attr) */ static int parse_event_symbols(const char **str, struct perf_counter_attr *attr) { - if (!(parse_raw_event(str, attr) || + if (!(parse_tracepoint_event(str, attr) || + parse_raw_event(str, attr) || parse_numeric_event(str, attr) || parse_symbolic_event(str, attr) || parse_generic_hw_event(str, attr))) @@ -422,6 +557,42 @@ static const char * const event_type_descriptors[] = { "Hardware cache event", }; +/* + * Print the events from /tracing/events + */ + +static void print_tracepoint_events(void) +{ + DIR *sys_dir, *evt_dir; + struct dirent *sys_next, *evt_next, sys_dirent, evt_dirent; + struct stat st; + char evt_path[MAXPATHLEN]; + + if (valid_debugfs_mount()) + return; + + sys_dir = opendir(default_debugfs_path); + if (!sys_dir) + goto cleanup; + + for_each_subsystem(sys_dir, sys_dirent, sys_next, evt_path, st) { + evt_dir = opendir(evt_path); + if (!evt_dir) + goto cleanup; + for_each_event(sys_dirent, evt_dir, evt_dirent, evt_next, + evt_path, st) { + snprintf(evt_path, MAXPATHLEN, "%s:%s", + sys_dirent.d_name, evt_dirent.d_name); + fprintf(stderr, " %-40s [%s]\n", evt_path, + event_type_descriptors[PERF_TYPE_TRACEPOINT+1]); + } + closedir(evt_dir); + } + +cleanup: + closedir(sys_dir); +} + /* * Print the help text for the event symbols: */ @@ -472,5 +643,7 @@ void print_events(void) "rNNN"); fprintf(stderr, "\n"); + print_tracepoint_events(); + exit(129); } diff --git a/tools/perf/util/util.h b/tools/perf/util/util.h index b4be6071c10..68fe157d72f 100644 --- a/tools/perf/util/util.h +++ b/tools/perf/util/util.h @@ -50,6 +50,7 @@ #include #include #include +#include #include #include #include @@ -80,6 +81,7 @@ #include #include #include +#include "../../../include/linux/magic.h" #ifndef NO_ICONV #include -- GitLab From 5beeded123c5befa21f1c6e16219f2a3eb7dd197 Mon Sep 17 00:00:00 2001 From: Jason Baron Date: Tue, 21 Jul 2009 14:16:29 -0400 Subject: [PATCH 0200/1342] perf_counter: Detect debugfs location If "/sys/kernel/debug" is not a debugfs mount point, search for the debugfs filesystem in /proc/mounts, but also allows the user to specify '--debugfs-dir=blah' or set the environment variable: 'PERF_DEBUGFS_DIR' Signed-off-by: Jason Baron [ also made it probe "/debug" by default ] Signed-off-by: Peter Zijlstra LKML-Reference: <20090721181629.GA3094@redhat.com> --- tools/perf/perf.c | 77 +++++++++++++++++++++++++++++++++- tools/perf/util/cache.h | 1 + tools/perf/util/parse-events.c | 33 ++++++++------- tools/perf/util/parse-events.h | 5 +++ tools/perf/util/string.h | 3 ++ 5 files changed, 102 insertions(+), 17 deletions(-) diff --git a/tools/perf/perf.c b/tools/perf/perf.c index c5656784c61..31982ad064b 100644 --- a/tools/perf/perf.c +++ b/tools/perf/perf.c @@ -12,6 +12,8 @@ #include "util/cache.h" #include "util/quote.h" #include "util/run-command.h" +#include "util/parse-events.h" +#include "util/string.h" const char perf_usage_string[] = "perf [--version] [--help] COMMAND [ARGS]"; @@ -25,6 +27,8 @@ struct pager_config { int val; }; +static char debugfs_mntpt[MAXPATHLEN]; + static int pager_command_config(const char *var, const char *value, void *data) { struct pager_config *c = data; @@ -56,6 +60,15 @@ static void commit_pager_choice(void) { } } +static void set_debugfs_path(void) +{ + char *path; + + path = getenv(PERF_DEBUGFS_ENVIRONMENT); + snprintf(debugfs_path, MAXPATHLEN, "%s/%s", path ?: debugfs_mntpt, + "tracing/events"); +} + static int handle_options(const char*** argv, int* argc, int* envchanged) { int handled = 0; @@ -122,6 +135,22 @@ static int handle_options(const char*** argv, int* argc, int* envchanged) setenv(PERF_WORK_TREE_ENVIRONMENT, cmd + 12, 1); if (envchanged) *envchanged = 1; + } else if (!strcmp(cmd, "--debugfs-dir")) { + if (*argc < 2) { + fprintf(stderr, "No directory given for --debugfs-dir.\n"); + usage(perf_usage_string); + } + strncpy(debugfs_mntpt, (*argv)[1], MAXPATHLEN); + debugfs_mntpt[MAXPATHLEN - 1] = '\0'; + if (envchanged) + *envchanged = 1; + (*argv)++; + (*argc)--; + } else if (!prefixcmp(cmd, "--debugfs-dir=")) { + strncpy(debugfs_mntpt, cmd + 14, MAXPATHLEN); + debugfs_mntpt[MAXPATHLEN - 1] = '\0'; + if (envchanged) + *envchanged = 1; } else { fprintf(stderr, "Unknown option: %s\n", cmd); usage(perf_usage_string); @@ -228,6 +257,7 @@ static int run_builtin(struct cmd_struct *p, int argc, const char **argv) if (use_pager == -1 && p->option & USE_PAGER) use_pager = 1; commit_pager_choice(); + set_debugfs_path(); status = p->fn(argc, argv, prefix); if (status) @@ -346,6 +376,49 @@ static int run_argv(int *argcp, const char ***argv) return done_alias; } +/* mini /proc/mounts parser: searching for "^blah /mount/point debugfs" */ +static void get_debugfs_mntpt(void) +{ + FILE *file; + char fs_type[100]; + char debugfs[MAXPATHLEN]; + + /* + * try the standard location + */ + if (valid_debugfs_mount("/sys/kernel/debug/") == 0) { + strcpy(debugfs_mntpt, "/sys/kernel/debug/"); + return; + } + + /* + * try the sane location + */ + if (valid_debugfs_mount("/debug/") == 0) { + strcpy(debugfs_mntpt, "/debug/"); + return; + } + + /* + * give up and parse /proc/mounts + */ + file = fopen("/proc/mounts", "r"); + if (file == NULL) + return; + + while (fscanf(file, "%*s %" + STR(MAXPATHLEN) + "s %99s %*s %*d %*d\n", + debugfs, fs_type) == 2) { + if (strcmp(fs_type, "debugfs") == 0) + break; + } + fclose(file); + if (strcmp(fs_type, "debugfs") == 0) { + strncpy(debugfs_mntpt, debugfs, MAXPATHLEN); + debugfs_mntpt[MAXPATHLEN - 1] = '\0'; + } +} int main(int argc, const char **argv) { @@ -354,7 +427,8 @@ int main(int argc, const char **argv) cmd = perf_extract_argv0_path(argv[0]); if (!cmd) cmd = "perf-help"; - + /* get debugfs mount point from /proc/mounts */ + get_debugfs_mntpt(); /* * "perf-xxxx" is the same as "perf xxxx", but we obviously: * @@ -377,6 +451,7 @@ int main(int argc, const char **argv) argc--; handle_options(&argv, &argc, NULL); commit_pager_choice(); + set_debugfs_path(); if (argc > 0) { if (!prefixcmp(argv[0], "--")) argv[0] += 2; diff --git a/tools/perf/util/cache.h b/tools/perf/util/cache.h index 161d5f413e2..4b50c412b9c 100644 --- a/tools/perf/util/cache.h +++ b/tools/perf/util/cache.h @@ -18,6 +18,7 @@ #define PERFATTRIBUTES_FILE ".perfattributes" #define INFOATTRIBUTES_FILE "info/attributes" #define ATTRIBUTE_MACRO_PREFIX "[attr]" +#define PERF_DEBUGFS_ENVIRONMENT "PERF_DEBUGFS_DIR" typedef int (*config_fn_t)(const char *, const char *, void *); extern int perf_default_config(const char *, const char *, void *); diff --git a/tools/perf/util/parse-events.c b/tools/perf/util/parse-events.c index 5a3cd3a34af..7bdad8df22a 100644 --- a/tools/perf/util/parse-events.c +++ b/tools/perf/util/parse-events.c @@ -5,6 +5,7 @@ #include "parse-events.h" #include "exec_cmd.h" #include "string.h" +#include "cache.h" extern char *strcasestr(const char *haystack, const char *needle); @@ -12,8 +13,6 @@ int nr_counters; struct perf_counter_attr attrs[MAX_COUNTERS]; -static char default_debugfs_path[] = "/sys/kernel/debug/tracing/events"; - struct event_symbol { u8 type; u64 config; @@ -21,6 +20,8 @@ struct event_symbol { char *alias; }; +char debugfs_path[MAXPATHLEN]; + #define CHW(x) .type = PERF_TYPE_HARDWARE, .config = PERF_COUNT_HW_##x #define CSW(x) .type = PERF_TYPE_SOFTWARE, .config = PERF_COUNT_SW_##x @@ -114,27 +115,27 @@ static unsigned long hw_cache_stat[C(MAX)] = { #define for_each_subsystem(sys_dir, sys_dirent, sys_next, file, st) \ while (!readdir_r(sys_dir, &sys_dirent, &sys_next) && sys_next) \ - if (snprintf(file, MAXPATHLEN, "%s/%s", default_debugfs_path, \ - sys_dirent.d_name) && \ + if (snprintf(file, MAXPATHLEN, "%s/%s", debugfs_path, \ + sys_dirent.d_name) && \ (!stat(file, &st)) && (S_ISDIR(st.st_mode)) && \ (strcmp(sys_dirent.d_name, ".")) && \ (strcmp(sys_dirent.d_name, ".."))) #define for_each_event(sys_dirent, evt_dir, evt_dirent, evt_next, file, st) \ while (!readdir_r(evt_dir, &evt_dirent, &evt_next) && evt_next) \ - if (snprintf(file, MAXPATHLEN, "%s/%s/%s", default_debugfs_path, \ - sys_dirent.d_name, evt_dirent.d_name) && \ + if (snprintf(file, MAXPATHLEN, "%s/%s/%s", debugfs_path, \ + sys_dirent.d_name, evt_dirent.d_name) && \ (!stat(file, &st)) && (S_ISDIR(st.st_mode)) && \ (strcmp(evt_dirent.d_name, ".")) && \ (strcmp(evt_dirent.d_name, ".."))) #define MAX_EVENT_LENGTH 30 -static int valid_debugfs_mount(void) +int valid_debugfs_mount(const char *debugfs) { struct statfs st_fs; - if (statfs(default_debugfs_path, &st_fs) < 0) + if (statfs(debugfs, &st_fs) < 0) return -ENOENT; else if (st_fs.f_type != (long) DEBUGFS_MAGIC) return -ENOENT; @@ -152,10 +153,10 @@ static char *tracepoint_id_to_name(u64 config) u64 id; char evt_path[MAXPATHLEN]; - if (valid_debugfs_mount()) + if (valid_debugfs_mount(debugfs_path)) return "unkown"; - sys_dir = opendir(default_debugfs_path); + sys_dir = opendir(debugfs_path); if (!sys_dir) goto cleanup; @@ -166,7 +167,7 @@ static char *tracepoint_id_to_name(u64 config) for_each_event(sys_dirent, evt_dir, evt_dirent, evt_next, evt_path, st) { snprintf(evt_path, MAXPATHLEN, "%s/%s/%s/id", - default_debugfs_path, sys_dirent.d_name, + debugfs_path, sys_dirent.d_name, evt_dirent.d_name); fd = open(evt_path, O_RDONLY); if (fd < 0) @@ -363,7 +364,7 @@ static int parse_tracepoint_event(const char **strp, u64 id; char evt_path[MAXPATHLEN]; - if (valid_debugfs_mount()) + if (valid_debugfs_mount(debugfs_path)) return 0; evt_name = strchr(*strp, ':'); @@ -381,8 +382,8 @@ static int parse_tracepoint_event(const char **strp, if (evt_length >= MAX_EVENT_LENGTH) return 0; - snprintf(evt_path, MAXPATHLEN, "%s/%s/%s/id", default_debugfs_path, - sys_name, evt_name); + snprintf(evt_path, MAXPATHLEN, "%s/%s/%s/id", debugfs_path, + sys_name, evt_name); fd = open(evt_path, O_RDONLY); if (fd < 0) return 0; @@ -568,10 +569,10 @@ static void print_tracepoint_events(void) struct stat st; char evt_path[MAXPATHLEN]; - if (valid_debugfs_mount()) + if (valid_debugfs_mount(debugfs_path)) return; - sys_dir = opendir(default_debugfs_path); + sys_dir = opendir(debugfs_path); if (!sys_dir) goto cleanup; diff --git a/tools/perf/util/parse-events.h b/tools/perf/util/parse-events.h index e3d552908e6..1ea5d09b6eb 100644 --- a/tools/perf/util/parse-events.h +++ b/tools/perf/util/parse-events.h @@ -3,6 +3,8 @@ * Parse symbolic events/counts passed in as options: */ +struct option; + extern int nr_counters; extern struct perf_counter_attr attrs[MAX_COUNTERS]; @@ -15,3 +17,6 @@ extern int parse_events(const struct option *opt, const char *str, int unset); extern void print_events(void); +extern char debugfs_path[]; +extern int valid_debugfs_mount(const char *debugfs); + diff --git a/tools/perf/util/string.h b/tools/perf/util/string.h index 3dca2f654cd..bf39dfadfd2 100644 --- a/tools/perf/util/string.h +++ b/tools/perf/util/string.h @@ -5,4 +5,7 @@ int hex2u64(const char *ptr, u64 *val); +#define _STR(x) #x +#define STR(x) _STR(x) + #endif -- GitLab From d20ff6bd6bba2e7e6681fa17565347b410c46ab3 Mon Sep 17 00:00:00 2001 From: Mike Galbraith Date: Mon, 20 Jul 2009 14:01:38 +0200 Subject: [PATCH 0201/1342] perf_counter tools: Fix vmlinux symbol generation breakage vmlinux meets the criteria for symbol adjustment, which breaks vmlinux generated symbols. Fix this by exempting vmlinux. This is a bit fragile in that someone could change the kernel dso's name, but currently that name is also hardwired. Signed-off-by: Mike Galbraith Cc: Ingo Molnar Signed-off-by: Peter Zijlstra LKML-Reference: <1248091298.18702.18.camel@marge.simson.net> --- tools/perf/util/symbol.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) diff --git a/tools/perf/util/symbol.c b/tools/perf/util/symbol.c index 98aee922acc..28106059bf1 100644 --- a/tools/perf/util/symbol.c +++ b/tools/perf/util/symbol.c @@ -525,7 +525,7 @@ static int dso__load_sym(struct dso *self, int fd, const char *name, GElf_Sym sym; Elf_Scn *sec, *sec_strndx; Elf *elf; - int nr = 0; + int nr = 0, kernel = !strcmp("[kernel]", self->name); elf = elf_begin(fd, ELF_C_READ_MMAP, NULL); if (elf == NULL) { @@ -571,10 +571,13 @@ static int dso__load_sym(struct dso *self, int fd, const char *name, nr_syms = shdr.sh_size / shdr.sh_entsize; memset(&sym, 0, sizeof(sym)); - self->adjust_symbols = (ehdr.e_type == ET_EXEC || + if (!kernel) { + self->adjust_symbols = (ehdr.e_type == ET_EXEC || elf_section_by_name(elf, &ehdr, &shdr, ".gnu.prelink_undo", NULL) != NULL); + } else self->adjust_symbols = 0; + elf_symtab__for_each_symbol(syms, nr_syms, index, sym) { struct symbol *f; const char *name; -- GitLab From 0fdc7e67dd312986e30b861adff48732bd33eb3f Mon Sep 17 00:00:00 2001 From: Mike Galbraith Date: Tue, 21 Jul 2009 10:30:36 +0200 Subject: [PATCH 0202/1342] perf_counter tools: Give perf top inherit option Currently, perf top -p only tracks the pid provided, which isn't very useful for watching forky loads, so give it an inherit option. Signed-off-by: Mike Galbraith Cc: Ingo Molnar Signed-off-by: Peter Zijlstra LKML-Reference: <1248165036.9795.10.camel@marge.simson.net> --- tools/perf/builtin-top.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/tools/perf/builtin-top.c b/tools/perf/builtin-top.c index 95d5c0ae375..c0a423004e1 100644 --- a/tools/perf/builtin-top.c +++ b/tools/perf/builtin-top.c @@ -58,6 +58,7 @@ static u64 count_filter = 5; static int print_entries = 15; static int target_pid = -1; +static int inherit = 0; static int profile_cpu = -1; static int nr_cpus = 0; static unsigned int realtime_prio = 0; @@ -549,7 +550,7 @@ int group_fd; static void start_counter(int i, int counter) { struct perf_counter_attr *attr; - unsigned int cpu; + int cpu; cpu = profile_cpu; if (target_pid == -1 && profile_cpu == -1) @@ -559,6 +560,7 @@ static void start_counter(int i, int counter) attr->sample_type = PERF_SAMPLE_IP | PERF_SAMPLE_TID; attr->freq = freq; + attr->inherit = (cpu < 0) && inherit; try_again: fd[i][counter] = sys_perf_counter_open(attr, target_pid, cpu, group_fd, 0); @@ -685,6 +687,8 @@ static const struct option options[] = { "only display functions with more events than this"), OPT_BOOLEAN('g', "group", &group, "put the counters into a counter group"), + OPT_BOOLEAN('i', "inherit", &inherit, + "child tasks inherit counters"), OPT_STRING('s', "sym-filter", &sym_filter, "pattern", "only display symbols matchig this pattern"), OPT_BOOLEAN('z', "zero", &zero, -- GitLab From 4012ade9338c05428162e85cc9b149dcadf1ce85 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Wed, 22 Jul 2009 18:15:10 +0200 Subject: [PATCH 0203/1342] ALSA: hda - Restore GPIO1 properly at resume with AD1984A The commit 099db17e66294b02814dee01c81d9abbbeece93e introduced a regression at suspend/resume where the GPIO1 bit isn't properly restored, thus the speaker output gets muted initially after resume. The fix is simple, use the cached write for storing GPIO data. Reference: Novell bnc#522764 https://bugzilla.novell.com/show_bug.cgi?id=522764 Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_analog.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/pci/hda/patch_analog.c b/sound/pci/hda/patch_analog.c index f795ee588cc..e8e6a43865c 100644 --- a/sound/pci/hda/patch_analog.c +++ b/sound/pci/hda/patch_analog.c @@ -3742,7 +3742,7 @@ static int ad1884a_mobile_master_sw_put(struct snd_kcontrol *kcontrol, int mute = (!ucontrol->value.integer.value[0] && !ucontrol->value.integer.value[1]); /* toggle GPIO1 according to the mute state */ - snd_hda_codec_write(codec, 0x01, 0, AC_VERB_SET_GPIO_DATA, + snd_hda_codec_write_cache(codec, 0x01, 0, AC_VERB_SET_GPIO_DATA, mute ? 0x02 : 0x0); return ret; } -- GitLab From 24c30dbbcdda9aeccb23b4eecb6bb8e538742ea4 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Thu, 16 Jul 2009 21:31:31 +0000 Subject: [PATCH 0204/1342] of/mdio: Add support function for Ethernet fixed-link property Fixed-link support is broken for the ucc_eth, gianfar, and fs_enet device drivers. The "OF MDIO rework" patches removed most of the support. Instead of re-adding fixed-link stuff to the drivers, this patch adds a support function for parsing the fixed-link property and obtaining a dummy phy to match. Note: the dummy phy handling in arch/powerpc is a bit of a hack and needs to be reworked. This function is being added now to solve the regression in the Ethernet drivers, but it should be considered a temporary measure until the fixed link handling can be reworked. Signed-off-by: Anton Vorontsov Signed-off-by: Grant Likely Signed-off-by: David S. Miller --- drivers/of/of_mdio.c | 42 +++++++++++++++++++++++++++++++++++++++++ include/linux/of_mdio.h | 3 +++ 2 files changed, 45 insertions(+) diff --git a/drivers/of/of_mdio.c b/drivers/of/of_mdio.c index aee967d7f76..bacaa536fd5 100644 --- a/drivers/of/of_mdio.c +++ b/drivers/of/of_mdio.c @@ -9,6 +9,10 @@ * out of the OpenFirmware device tree and using it to populate an mii_bus. */ +#include +#include +#include +#include #include #include #include @@ -137,3 +141,41 @@ struct phy_device *of_phy_connect(struct net_device *dev, return phy_connect_direct(dev, phy, hndlr, flags, iface) ? NULL : phy; } EXPORT_SYMBOL(of_phy_connect); + +/** + * of_phy_connect_fixed_link - Parse fixed-link property and return a dummy phy + * @dev: pointer to net_device claiming the phy + * @hndlr: Link state callback for the network device + * @iface: PHY data interface type + * + * This function is a temporary stop-gap and will be removed soon. It is + * only to support the fs_enet, ucc_geth and gianfar Ethernet drivers. Do + * not call this function from new drivers. + */ +struct phy_device *of_phy_connect_fixed_link(struct net_device *dev, + void (*hndlr)(struct net_device *), + phy_interface_t iface) +{ + struct device_node *net_np; + char bus_id[MII_BUS_ID_SIZE + 3]; + struct phy_device *phy; + const u32 *phy_id; + int sz; + + if (!dev->dev.parent) + return NULL; + + net_np = dev_archdata_get_node(&dev->dev.parent->archdata); + if (!net_np) + return NULL; + + phy_id = of_get_property(net_np, "fixed-link", &sz); + if (!phy_id || sz < sizeof(*phy_id)) + return NULL; + + sprintf(bus_id, PHY_ID_FMT, "0", phy_id[0]); + + phy = phy_connect(dev, bus_id, hndlr, 0, iface); + return IS_ERR(phy) ? NULL : phy; +} +EXPORT_SYMBOL(of_phy_connect_fixed_link); diff --git a/include/linux/of_mdio.h b/include/linux/of_mdio.h index c9663c69030..53b94e025c7 100644 --- a/include/linux/of_mdio.h +++ b/include/linux/of_mdio.h @@ -18,5 +18,8 @@ extern struct phy_device *of_phy_connect(struct net_device *dev, struct device_node *phy_np, void (*hndlr)(struct net_device *), u32 flags, phy_interface_t iface); +extern struct phy_device *of_phy_connect_fixed_link(struct net_device *dev, + void (*hndlr)(struct net_device *), + phy_interface_t iface); #endif /* __LINUX_OF_MDIO_H */ -- GitLab From eedbc705f9a094560b8d08c58b6787a5420a76a1 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Thu, 16 Jul 2009 21:31:36 +0000 Subject: [PATCH 0205/1342] fs_enet: Revive fixed link support Since commit aa73832c5a80d6c52c69b18af858d88fa595dd3c ("Rework fs_enet driver to use of_mdio infrastructure") the fixed-link support is broken in the fs_enet driver. This patch fixes the support by removing a check for phy_node, and adding a call to of_phy_connect_fixed_link(). Also set netdev parent device via SET_NETDEV_DEV() call, this is needed so that OF MDIO core could find a node pointer for a device. Plus, fix "if (IS_ERR(phydev))" check, in case of errors, of_phy_connect() returns NULL, not ERR_PTR as phy_connect(). Signed-off-by: Anton Vorontsov Signed-off-by: Grant Likely Signed-off-by: David S. Miller --- drivers/net/fs_enet/fs_enet-main.c | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) diff --git a/drivers/net/fs_enet/fs_enet-main.c b/drivers/net/fs_enet/fs_enet-main.c index b892c3ad9a7..2bc2d2b2064 100644 --- a/drivers/net/fs_enet/fs_enet-main.c +++ b/drivers/net/fs_enet/fs_enet-main.c @@ -754,17 +754,16 @@ static int fs_init_phy(struct net_device *dev) fep->oldlink = 0; fep->oldspeed = 0; fep->oldduplex = -1; - if(fep->fpi->phy_node) - phydev = of_phy_connect(dev, fep->fpi->phy_node, - &fs_adjust_link, 0, - PHY_INTERFACE_MODE_MII); - else { - printk("No phy bus ID specified in BSP code\n"); - return -EINVAL; + + phydev = of_phy_connect(dev, fep->fpi->phy_node, &fs_adjust_link, 0, + PHY_INTERFACE_MODE_MII); + if (!phydev) { + phydev = of_phy_connect_fixed_link(dev, &fs_adjust_link, + PHY_INTERFACE_MODE_MII); } - if (IS_ERR(phydev)) { - printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name); - return PTR_ERR(phydev); + if (!phydev) { + dev_err(&dev->dev, "Could not attach to PHY\n"); + return -ENODEV; } fep->phydev = phydev; @@ -1005,6 +1004,7 @@ static int __devinit fs_enet_probe(struct of_device *ofdev, goto out_free_fpi; } + SET_NETDEV_DEV(ndev, &ofdev->dev); dev_set_drvdata(&ofdev->dev, ndev); fep = netdev_priv(ndev); -- GitLab From 1db780f8c7d361fe1b7d29b9dc849b97955ae944 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Thu, 16 Jul 2009 21:31:42 +0000 Subject: [PATCH 0206/1342] gianfar: Revive fixed link support Since commit fe192a49118f5b1272317d60c7930ece4e13ae49 ("Rework gianfar driver to use of_mdio infrastructure") the fixed-link support is broken, the driver oopses at init_phy(): Unable to handle kernel paging request for data at address 0x000000e4 Faulting instruction address: 0xc01cf298 Oops: Kernel access of bad area, sig: 11 [#1] [...] NIP [c01cf298] init_phy+0x80/0xdc LR [c01cf250] init_phy+0x38/0xdc Call Trace: [cf81fe80] [c01d1cf8] gfar_enet_open+0x6c/0x19c [cf81fea0] [c024494c] dev_open+0xfc/0x134 [cf81fec0] [c0242edc] dev_change_flags+0x84/0x1ac [cf81fee0] [c0399ee0] ic_open_devs+0x168/0x2d8 [cf81ff20] [c039b2e8] ip_auto_config+0x90/0x2a4 [cf81ff60] [c0003884] do_one_initcall+0x34/0x1a8 This patch fixes the oops, and removes phy_node checks, and adds a call to of_phy_connect_fixed_link() if a phy isn't attached.. Also, remove an old fixed-link code that we don't use any longer. Signed-off-by: Anton Vorontsov Signed-off-by: Grant Likely Signed-off-by: David S. Miller --- drivers/net/gianfar.c | 24 ++++++++---------------- 1 file changed, 8 insertions(+), 16 deletions(-) diff --git a/drivers/net/gianfar.c b/drivers/net/gianfar.c index 43d813ed9f4..f8ffcbf0bc3 100644 --- a/drivers/net/gianfar.c +++ b/drivers/net/gianfar.c @@ -264,15 +264,6 @@ static int gfar_of_init(struct net_device *dev) priv->device_flags |= FSL_GIANFAR_DEV_HAS_MAGIC_PACKET; priv->phy_node = of_parse_phandle(np, "phy-handle", 0); - if (!priv->phy_node) { - u32 *fixed_link; - - fixed_link = (u32 *)of_get_property(np, "fixed-link", NULL); - if (!fixed_link) { - err = -ENODEV; - goto err_out; - } - } /* Find the TBI PHY. If it's not there, we don't support SGMII */ priv->tbi_node = of_parse_phandle(np, "tbi-handle", 0); @@ -659,13 +650,14 @@ static int init_phy(struct net_device *dev) interface = gfar_get_interface(dev); - if (priv->phy_node) { - priv->phydev = of_phy_connect(dev, priv->phy_node, &adjust_link, - 0, interface); - if (!priv->phydev) { - dev_err(&dev->dev, "error: Could not attach to PHY\n"); - return -ENODEV; - } + priv->phydev = of_phy_connect(dev, priv->phy_node, &adjust_link, 0, + interface); + if (!priv->phydev) + priv->phydev = of_phy_connect_fixed_link(dev, &adjust_link, + interface); + if (!priv->phydev) { + dev_err(&dev->dev, "could not attach to PHY\n"); + return -ENODEV; } if (interface == PHY_INTERFACE_MODE_SGMII) -- GitLab From 3104a6ff67e484e4dc84822b4ed0396e85bb9fb9 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Thu, 16 Jul 2009 21:31:47 +0000 Subject: [PATCH 0207/1342] ucc_geth: Revive fixed link support Since commit 0b9da337dca972e7a4144e298ec3adb8f244d4a4 ("Rework ucc_geth driver to use of_mdio infrastructure") the fixed-link support is broken. This patch fixes the support by removing !ug_info->phy_node check, and adds a call to of_phy_connect_fixed_link() if a phy is not attached to the MAC. Also, remove an old fixed-link code that we don't use any longer. Signed-off-by: Anton Vorontsov Signed-off-by: Grant Likely Signed-off-by: David S. Miller --- drivers/net/ucc_geth.c | 23 +++++++---------------- 1 file changed, 7 insertions(+), 16 deletions(-) diff --git a/drivers/net/ucc_geth.c b/drivers/net/ucc_geth.c index 40c6eba775c..3b957e6412e 100644 --- a/drivers/net/ucc_geth.c +++ b/drivers/net/ucc_geth.c @@ -1590,13 +1590,13 @@ static int init_phy(struct net_device *dev) priv->oldspeed = 0; priv->oldduplex = -1; - if (!ug_info->phy_node) - return 0; - phydev = of_phy_connect(dev, ug_info->phy_node, &adjust_link, 0, priv->phy_interface); + if (!phydev) + phydev = of_phy_connect_fixed_link(dev, &adjust_link, + priv->phy_interface); if (!phydev) { - printk("%s: Could not attach to PHY\n", dev->name); + dev_err(&dev->dev, "Could not attach to PHY\n"); return -ENODEV; } @@ -3608,9 +3608,7 @@ static int ucc_geth_probe(struct of_device* ofdev, const struct of_device_id *ma struct ucc_geth_private *ugeth = NULL; struct ucc_geth_info *ug_info; struct resource res; - struct device_node *phy; int err, ucc_num, max_speed = 0; - const u32 *fixed_link; const unsigned int *prop; const char *sprop; const void *mac_addr; @@ -3708,15 +3706,8 @@ static int ucc_geth_probe(struct of_device* ofdev, const struct of_device_id *ma ug_info->uf_info.regs = res.start; ug_info->uf_info.irq = irq_of_parse_and_map(np, 0); - fixed_link = of_get_property(np, "fixed-link", NULL); - if (fixed_link) { - phy = NULL; - } else { - phy = of_parse_phandle(np, "phy-handle", 0); - if (phy == NULL) - return -ENODEV; - } - ug_info->phy_node = phy; + + ug_info->phy_node = of_parse_phandle(np, "phy-handle", 0); /* Find the TBI PHY node. If it's not there, we don't support SGMII */ ug_info->tbi_node = of_parse_phandle(np, "tbi-handle", 0); @@ -3725,7 +3716,7 @@ static int ucc_geth_probe(struct of_device* ofdev, const struct of_device_id *ma prop = of_get_property(np, "phy-connection-type", NULL); if (!prop) { /* handle interface property present in old trees */ - prop = of_get_property(phy, "interface", NULL); + prop = of_get_property(ug_info->phy_node, "interface", NULL); if (prop != NULL) { phy_interface = enet_to_phy_interface[*prop]; max_speed = enet_to_speed[*prop]; -- GitLab From fa77406aee9d33f35c7202dcd83436feb12d9fc3 Mon Sep 17 00:00:00 2001 From: Ajit Khaparde Date: Wed, 22 Jul 2009 09:28:55 -0700 Subject: [PATCH 0208/1342] be2net: Bug fix in the non-lro path. Size of received packet was not updated in statistics properly. This patch fixes a bug in the non-lro path. Wrong size of received packet was being passed for updating receive statistics. This patch is against the net-2.6 git. Signed-off-by: Ajit Khaparde Signed-off-by: David S. Miller --- drivers/net/benet/be_main.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/net/benet/be_main.c b/drivers/net/benet/be_main.c index c43f6a11929..dea3155688b 100644 --- a/drivers/net/benet/be_main.c +++ b/drivers/net/benet/be_main.c @@ -667,7 +667,7 @@ static void skb_fill_rx_data(struct be_adapter *adapter, struct be_queue_info *rxq = &adapter->rx_obj.q; struct be_rx_page_info *page_info; u16 rxq_idx, i, num_rcvd, j; - u32 pktsize, hdr_len, curr_frag_len; + u32 pktsize, hdr_len, curr_frag_len, size; u8 *start; rxq_idx = AMAP_GET_BITS(struct amap_eth_rx_compl, fragndx, rxcp); @@ -708,12 +708,13 @@ static void skb_fill_rx_data(struct be_adapter *adapter, } /* More frags present for this completion */ - pktsize -= curr_frag_len; /* account for above copied frag */ + size = pktsize; for (i = 1, j = 0; i < num_rcvd; i++) { + size -= curr_frag_len; index_inc(&rxq_idx, rxq->len); page_info = get_rx_page_info(adapter, rxq_idx); - curr_frag_len = min(pktsize, rx_frag_size); + curr_frag_len = min(size, rx_frag_size); /* Coalesce all frags from the same physical page in one slot */ if (page_info->page_offset == 0) { @@ -731,7 +732,6 @@ static void skb_fill_rx_data(struct be_adapter *adapter, skb_shinfo(skb)->frags[j].size += curr_frag_len; skb->len += curr_frag_len; skb->data_len += curr_frag_len; - pktsize -= curr_frag_len; memset(page_info, 0, sizeof(*page_info)); } -- GitLab From 0dc3d523e8bc4718e0be2e4a742367d6e4be77cd Mon Sep 17 00:00:00 2001 From: Arjan van de Ven Date: Tue, 21 Jul 2009 00:55:05 -0700 Subject: [PATCH 0209/1342] perf: fix stack data leak the "reserved" field was not initialized to zero, resulting in 4 bytes of stack data leaking to userspace.... Signed-off-by: Arjan van de Ven Acked-by: Peter Zijlstra Signed-off-by: Linus Torvalds --- kernel/perf_counter.c | 1 + 1 file changed, 1 insertion(+) diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index a641eb753b8..7bc888dfd06 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -2665,6 +2665,7 @@ static void perf_counter_output(struct perf_counter *counter, int nmi, header.size += sizeof(cpu_entry); cpu_entry.cpu = raw_smp_processor_id(); + cpu_entry.reserved = 0; } if (sample_type & PERF_SAMPLE_PERIOD) -- GitLab From de72e5de062e48a992d6cafe2291a82fe498d641 Mon Sep 17 00:00:00 2001 From: Alexander Beregalov Date: Wed, 22 Jul 2009 01:16:51 +0000 Subject: [PATCH 0210/1342] net: KS8851 needs to depend on MII fix this build error when CONFIG_MII is not set drivers/net/ks8851.c:999: undefined reference to `generic_mii_ioctl' drivers/net/ks8851.c:1050: undefined reference to `mii_link_ok' drivers/net/ks8851.c:1056: undefined reference to `mii_nway_restart' drivers/net/ks8851.c:1044: undefined reference to `mii_ethtool_sset' drivers/net/ks8851.c:1038: undefined reference to `mii_ethtool_gset' Signed-off-by: Alexander Beregalov Acked-by: Ben Dooks --- drivers/net/Kconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index b5a7513df4e..5f6509a5f64 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -1732,6 +1732,7 @@ config KS8842 config KS8851 tristate "Micrel KS8851 SPI" depends on SPI + select MII help SPI driver for Micrel KS8851 SPI attached network chip. -- GitLab From 2cb078603abb612e3bcd428fb8122c3d39e08832 Mon Sep 17 00:00:00 2001 From: Jeremy Fitzhardinge Date: Wed, 22 Jul 2009 09:59:35 -0700 Subject: [PATCH 0211/1342] x86, amd: Don't probe for extended APIC ID if APICs are disabled If we've logically disabled apics, don't probe the PCI space for the AMD extended APIC ID. [ Impact: prevent boot crash under Xen. ] Signed-off-by: Jeremy Fitzhardinge Reported-by: Bastian Blank Signed-off-by: H. Peter Anvin --- arch/x86/kernel/cpu/amd.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/cpu/amd.c b/arch/x86/kernel/cpu/amd.c index 28e5f595604..e2485b03f1c 100644 --- a/arch/x86/kernel/cpu/amd.c +++ b/arch/x86/kernel/cpu/amd.c @@ -356,7 +356,7 @@ static void __cpuinit early_init_amd(struct cpuinfo_x86 *c) #endif #if defined(CONFIG_X86_LOCAL_APIC) && defined(CONFIG_PCI) /* check CPU config space for extended APIC ID */ - if (c->x86 >= 0xf) { + if (cpu_has_apic && c->x86 >= 0xf) { unsigned int val; val = read_pci_config(0, 24, 0, 0x68); if ((val & ((1 << 17) | (1 << 18))) == ((1 << 17) | (1 << 18))) -- GitLab From 7b55a4a3f761db7daba1ac526ef60f64f5c53689 Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Wed, 22 Jul 2009 02:58:55 +0000 Subject: [PATCH 0212/1342] skge: Enable WoL by default if supported If skge hardware is capable of waking up the system from sleep, enable magic packet WoL during driver initialisation. This makes WoL work without calling 'ethtool -s ethX wol g' for each adapter. Signed-off-by: Rafael J. Wysocki Tested-by: Michael Guntsche Acked-by: Stephen Hemminger Signed-off-by: David S. Miller --- drivers/net/skge.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/net/skge.c b/drivers/net/skge.c index 60d502eef4f..543af2044f4 100644 --- a/drivers/net/skge.c +++ b/drivers/net/skge.c @@ -3854,8 +3854,10 @@ static struct net_device *skge_devinit(struct skge_hw *hw, int port, skge->speed = -1; skge->advertising = skge_supported_modes(hw); - if (device_may_wakeup(&hw->pdev->dev)) + if (device_can_wakeup(&hw->pdev->dev)) { skge->wol = wol_supported(hw) & WAKE_MAGIC; + device_set_wakeup_enable(&hw->pdev->dev, skge->wol); + } hw->dev[port] = dev; -- GitLab From 78a9c9c97455d0f8d2d2098b2252eb4bf65be799 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= Date: Tue, 21 Jul 2009 10:11:39 +0000 Subject: [PATCH 0213/1342] register at91_ether using platform_driver_probe MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit at91ether_probe lives in .init.text, so using platform_driver_register to register it is wrong because binding a device after the init memory is discarded (e.g. via sysfs) results in an oops. As requested by David Brownell platform_driver_probe is used instead of moving the probe function to .devinit.text as proposed initially. This saves some memory, but devices registered after the driver is probed are not bound (probably there are none) and binding via sysfs isn't possible. Signed-off-by: Uwe Kleine-König Acked-by: David Brownell Acked-by: Andrew Victor Signed-off-by: David S. Miller --- drivers/net/arm/at91_ether.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/drivers/net/arm/at91_ether.c b/drivers/net/arm/at91_ether.c index 2e7419a6119..5041d10bae9 100644 --- a/drivers/net/arm/at91_ether.c +++ b/drivers/net/arm/at91_ether.c @@ -1228,7 +1228,6 @@ static int at91ether_resume(struct platform_device *pdev) #endif static struct platform_driver at91ether_driver = { - .probe = at91ether_probe, .remove = __devexit_p(at91ether_remove), .suspend = at91ether_suspend, .resume = at91ether_resume, @@ -1240,7 +1239,7 @@ static struct platform_driver at91ether_driver = { static int __init at91ether_init(void) { - return platform_driver_register(&at91ether_driver); + return platform_driver_probe(&at91ether_driver, at91ether_probe); } static void __exit at91ether_exit(void) -- GitLab From 023d43c7b5a23a81fe8afa9f37296f8ed4be11fb Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Tue, 21 Jul 2009 10:09:23 +0200 Subject: [PATCH 0214/1342] lockdep: Fix lockdep annotation for pipe_double_lock() The presumed use of the pipe_double_lock() routine is to lock 2 locks in a deadlock free way by ordering the locks by their address. However it fails to keep the specified lock classes in order and explicitly annotates a deadlock. Rectify this. Signed-off-by: Peter Zijlstra Acked-by: Miklos Szeredi LKML-Reference: <1248163763.15751.11098.camel@twins> --- fs/pipe.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/fs/pipe.c b/fs/pipe.c index f7dd21ad85a..52c41511483 100644 --- a/fs/pipe.c +++ b/fs/pipe.c @@ -68,8 +68,8 @@ void pipe_double_lock(struct pipe_inode_info *pipe1, pipe_lock_nested(pipe1, I_MUTEX_PARENT); pipe_lock_nested(pipe2, I_MUTEX_CHILD); } else { - pipe_lock_nested(pipe2, I_MUTEX_CHILD); - pipe_lock_nested(pipe1, I_MUTEX_PARENT); + pipe_lock_nested(pipe2, I_MUTEX_PARENT); + pipe_lock_nested(pipe1, I_MUTEX_CHILD); } } -- GitLab From 29c5e8ce01f9dad7e24b99c21e4f836d6b0289e0 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Wed, 22 Jul 2009 16:49:00 -0400 Subject: [PATCH 0215/1342] Btrfs: convert nested spin_lock_irqsave to spin_lock If spin_lock_irqsave is called twice in a row with the same second argument, the interrupt state at the point of the second call overwrites the value saved by the first call. Indeed, the second call does not need to save the interrupt state, so it is changed to a simple spin_lock. Signed-off-by: Julia Lawall Signed-off-by: Chris Mason --- fs/btrfs/async-thread.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/fs/btrfs/async-thread.c b/fs/btrfs/async-thread.c index 6e4f6c50a12..019e8af449a 100644 --- a/fs/btrfs/async-thread.c +++ b/fs/btrfs/async-thread.c @@ -424,11 +424,11 @@ int btrfs_requeue_work(struct btrfs_work *work) * list */ if (worker->idle) { - spin_lock_irqsave(&worker->workers->lock, flags); + spin_lock(&worker->workers->lock); worker->idle = 0; list_move_tail(&worker->worker_list, &worker->workers->worker_list); - spin_unlock_irqrestore(&worker->workers->lock, flags); + spin_unlock(&worker->workers->lock); } if (!worker->working) { wake = 1; -- GitLab From 3acada49c2794c5aac21849e2ea05790c6dd2faa Mon Sep 17 00:00:00 2001 From: David Woodhouse Date: Wed, 22 Jul 2009 16:49:01 -0400 Subject: [PATCH 0216/1342] Btrfs: Remove broken sanity check from btrfs_rmap_block() It was never actually doing anything anyway (see the loop condition), and it would be difficult to make it work for RAID[56]. Even if it was actually working, it's checking for the wrong thing anyway. Instead of checking whether we list a block which _doesn't_ land at the relevant physical location, it should be checking that we _have_ listed all the logical blocks which refer to the required physical location on all devices. This function is only called from remove_sb_from_cache() to ensure that we reserve the logical blocks which would reside at the same physical location as the superblock copies. So listing more blocks than we need is actually OK. With RAID[56] we're going to throw away an entire stripe for each block we have to ignore, so we _are_ going to list blocks other than the ones which actually contain the superblock. Signed-off-by: David Woodhouse Signed-off-by: Chris Mason --- fs/btrfs/volumes.c | 20 -------------------- 1 file changed, 20 deletions(-) diff --git a/fs/btrfs/volumes.c b/fs/btrfs/volumes.c index f057730a72b..55c37276a29 100644 --- a/fs/btrfs/volumes.c +++ b/fs/btrfs/volumes.c @@ -2795,26 +2795,6 @@ int btrfs_rmap_block(struct btrfs_mapping_tree *map_tree, } } - for (i = 0; i > nr; i++) { - struct btrfs_multi_bio *multi; - struct btrfs_bio_stripe *stripe; - int ret; - - length = 1; - ret = btrfs_map_block(map_tree, WRITE, buf[i], - &length, &multi, 0); - BUG_ON(ret); - - stripe = multi->stripes; - for (j = 0; j < multi->num_stripes; j++) { - if (stripe->physical >= physical && - physical < stripe->physical + length) - break; - } - BUG_ON(j >= multi->num_stripes); - kfree(multi); - } - *logical = buf; *naddrs = nr; *stripe_len = map->stripe_len; -- GitLab From 33c17ad5717c887568c1de61f15e5d58ed66d189 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Wed, 22 Jul 2009 16:49:01 -0400 Subject: [PATCH 0217/1342] Btrfs: adjust NULL test Move the call to BUG_ON to before the dereference of the tested value. Signed-off-by: Julia Lawall Signed-off-by: Chris Mason --- fs/btrfs/inode.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/btrfs/inode.c b/fs/btrfs/inode.c index a48c084f6d3..3ea827ddf0f 100644 --- a/fs/btrfs/inode.c +++ b/fs/btrfs/inode.c @@ -2607,8 +2607,8 @@ noinline int btrfs_truncate_inode_items(struct btrfs_trans_handle *trans, if (root->ref_cows) btrfs_drop_extent_cache(inode, new_size & (~mask), (u64)-1, 0); path = btrfs_alloc_path(); - path->reada = -1; BUG_ON(!path); + path->reada = -1; /* FIXME, add redo link to tree so we don't leak on crash */ key.objectid = inode->i_ino; -- GitLab From c271b492419a18908ba19ee02b231fb305a27023 Mon Sep 17 00:00:00 2001 From: Daniel Cadete Date: Wed, 22 Jul 2009 16:52:13 -0400 Subject: [PATCH 0218/1342] Btrfs: remove of redundant btrfs_header_level This removes the continues call's of btrfs_header_level. One call of btrfs_header_level(c) its enough. Signed-off-by Daniel Cadete Signed-off-by: Chris Mason --- fs/btrfs/print-tree.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/fs/btrfs/print-tree.c b/fs/btrfs/print-tree.c index 6d6523da0a3..0d126be22b6 100644 --- a/fs/btrfs/print-tree.c +++ b/fs/btrfs/print-tree.c @@ -309,7 +309,7 @@ void btrfs_print_tree(struct btrfs_root *root, struct extent_buffer *c) } printk(KERN_INFO "node %llu level %d total ptrs %d free spc %u\n", (unsigned long long)btrfs_header_bytenr(c), - btrfs_header_level(c), nr, + level, nr, (u32)BTRFS_NODEPTRS_PER_BLOCK(root) - nr); for (i = 0; i < nr; i++) { btrfs_node_key_to_cpu(c, &key, i); @@ -326,10 +326,10 @@ void btrfs_print_tree(struct btrfs_root *root, struct extent_buffer *c) btrfs_level_size(root, level - 1), btrfs_node_ptr_generation(c, i)); if (btrfs_is_leaf(next) && - btrfs_header_level(c) != 1) + level != 1) BUG(); if (btrfs_header_level(next) != - btrfs_header_level(c) - 1) + level - 1) BUG(); btrfs_print_tree(root, next); free_extent_buffer(next); -- GitLab From 83121942b28daffc9526b14b7843d8cdbd3db641 Mon Sep 17 00:00:00 2001 From: David Woodhouse Date: Wed, 22 Jul 2009 16:52:13 -0400 Subject: [PATCH 0219/1342] Btrfs: Fix crash on read failures at mount If the tree roots hit read errors during mount, btrfs is not properly erroring out. We need to check the uptodate bits after reading in the tree root node. Signed-off-by: David Woodhouse Signed-off-by: Chris Mason --- fs/btrfs/disk-io.c | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/fs/btrfs/disk-io.c b/fs/btrfs/disk-io.c index 0d50d49d990..55d9d188e69 100644 --- a/fs/btrfs/disk-io.c +++ b/fs/btrfs/disk-io.c @@ -1783,6 +1783,11 @@ struct btrfs_root *open_ctree(struct super_block *sb, btrfs_super_chunk_root(disk_super), blocksize, generation); BUG_ON(!chunk_root->node); + if (!test_bit(EXTENT_BUFFER_UPTODATE, &chunk_root->node->bflags)) { + printk(KERN_WARNING "btrfs: failed to read chunk root on %s\n", + sb->s_id); + goto fail_chunk_root; + } btrfs_set_root_node(&chunk_root->root_item, chunk_root->node); chunk_root->commit_root = btrfs_root_node(chunk_root); @@ -1810,6 +1815,11 @@ struct btrfs_root *open_ctree(struct super_block *sb, blocksize, generation); if (!tree_root->node) goto fail_chunk_root; + if (!test_bit(EXTENT_BUFFER_UPTODATE, &tree_root->node->bflags)) { + printk(KERN_WARNING "btrfs: failed to read tree root on %s\n", + sb->s_id); + goto fail_tree_root; + } btrfs_set_root_node(&tree_root->root_item, tree_root->node); tree_root->commit_root = btrfs_root_node(tree_root); -- GitLab From ce6e7fcd43aab1f77e56aa36936dd7d2d05a1ffa Mon Sep 17 00:00:00 2001 From: Jeff Layton Date: Wed, 22 Jul 2009 15:08:58 -0400 Subject: [PATCH 0220/1342] cifs: disable serverino if server doesn't support it A recent regression when dealing with older servers. This bug was introduced when we made serverino the default... When the server can't provide inode numbers, disable it for the mount. Signed-off-by: Jeff Layton Signed-off-by: Steve French --- fs/cifs/inode.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/fs/cifs/inode.c b/fs/cifs/inode.c index 18afe57b246..b6a47b32f21 100644 --- a/fs/cifs/inode.c +++ b/fs/cifs/inode.c @@ -513,9 +513,12 @@ int cifs_get_inode_info(struct inode **pinode, cifs_sb->mnt_cifs_flags & CIFS_MOUNT_MAP_SPECIAL_CHR); if (rc1) { - /* BB EOPNOSUPP disable SERVER_INUM? */ cFYI(1, ("GetSrvInodeNum rc %d", rc1)); fattr.cf_uniqueid = iunique(sb, ROOT_I); + /* disable serverino if call not supported */ + if (rc1 == -EINVAL) + cifs_sb->mnt_cifs_flags &= + ~CIFS_MOUNT_SERVER_INUM; } } else { fattr.cf_uniqueid = iunique(sb, ROOT_I); -- GitLab From 03aa3a49ad3592a9e4e1ab19c6da3e852288caf1 Mon Sep 17 00:00:00 2001 From: Jeff Layton Date: Tue, 21 Jul 2009 19:42:03 -0400 Subject: [PATCH 0221/1342] cifs: fix sb->s_maxbytes so that it casts properly to a signed value This off-by-one bug causes sendfile() to not work properly. When a task calls sendfile() on a file on a CIFS filesystem, the syscall returns -1 and sets errno to EOVERFLOW. do_sendfile uses s_maxbytes to verify the returned offset of the file. The problem there is that this value is cast to a signed value (loff_t). When this is done on the s_maxbytes value that cifs uses, it becomes negative and the comparisons against it fail. Even though s_maxbytes is an unsigned value, it seems that it's not OK to set it in such a way that it'll end up negative when it's cast to a signed value. These casts happen in other codepaths besides sendfile too, but the VFS is a little hard to follow in this area and I can't be sure if there are other bugs that this will fix. It's not clear to me why s_maxbytes isn't just declared as loff_t in the first place, but either way we still need to fix these values to make sendfile work properly. This is also an opportunity to replace the magic bit-shift values here with the standard #defines for this. This fixes the reproducer program I have that does a sendfile and will probably also fix the situation where apache is serving from a CIFS share. Acked-by: Johannes Weiner Signed-off-by: Jeff Layton Signed-off-by: Steve French --- fs/cifs/connect.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/fs/cifs/connect.c b/fs/cifs/connect.c index 9bb5c875073..fc44d316d0b 100644 --- a/fs/cifs/connect.c +++ b/fs/cifs/connect.c @@ -2452,10 +2452,10 @@ try_mount_again: tcon->local_lease = volume_info->local_lease; } if (pSesInfo) { - if (pSesInfo->capabilities & CAP_LARGE_FILES) { - sb->s_maxbytes = (u64) 1 << 63; - } else - sb->s_maxbytes = (u64) 1 << 31; /* 2 GB */ + if (pSesInfo->capabilities & CAP_LARGE_FILES) + sb->s_maxbytes = MAX_LFS_FILESIZE; + else + sb->s_maxbytes = MAX_NON_LFS; } /* BB FIXME fix time_gran to be larger for LANMAN sessions */ -- GitLab From 61f3826133dc07142935fb5712fc738e19eb5575 Mon Sep 17 00:00:00 2001 From: Bruno Premont Date: Wed, 22 Jul 2009 22:22:32 +0200 Subject: [PATCH 0222/1342] genirq: Fix UP compile failure caused by irq_thread_check_affinity Since genirq: Delegate irq affinity setting to the irq thread (591d2fb02ea80472d846c0b8507007806bdd69cc) compilation with CONFIG_SMP=n fails with following error: /usr/src/linux-2.6/kernel/irq/manage.c: In function 'irq_thread_check_affinity': /usr/src/linux-2.6/kernel/irq/manage.c:475: error: 'struct irq_desc' has no member named 'affinity' make[4]: *** [kernel/irq/manage.o] Error 1 That commit adds a new function irq_thread_check_affinity() which uses struct irq_desc.affinity which is only available for CONFIG_SMP=y. Move that function under #ifdef CONFIG_SMP. [ tglx@brownpaperbag: compile and boot tested on UP and SMP ] Signed-off-by: Bruno Premont LKML-Reference: <20090722222232.2eb3e1c4@neptune.home> Signed-off-by: Thomas Gleixner --- kernel/irq/manage.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/kernel/irq/manage.c b/kernel/irq/manage.c index f0de36f13a4..61c679db468 100644 --- a/kernel/irq/manage.c +++ b/kernel/irq/manage.c @@ -451,6 +451,7 @@ static int irq_wait_for_interrupt(struct irqaction *action) return -1; } +#ifdef CONFIG_SMP /* * Check whether we need to change the affinity of the interrupt thread. */ @@ -478,6 +479,10 @@ irq_thread_check_affinity(struct irq_desc *desc, struct irqaction *action) set_cpus_allowed_ptr(current, mask); free_cpumask_var(mask); } +#else +static inline void +irq_thread_check_affinity(struct irq_desc *desc, struct irqaction *action) { } +#endif /* * Interrupt handler thread -- GitLab From f1230c97978f52268d8c66e6f88e54c3d2092a75 Mon Sep 17 00:00:00 2001 From: Steve French Date: Wed, 22 Jul 2009 23:13:01 +0000 Subject: [PATCH 0223/1342] [CIFS] fix sparse warning Signed-off-by: Steve French --- fs/cifs/inode.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/fs/cifs/inode.c b/fs/cifs/inode.c index b6a47b32f21..82d83839655 100644 --- a/fs/cifs/inode.c +++ b/fs/cifs/inode.c @@ -212,7 +212,7 @@ cifs_unix_basic_to_fattr(struct cifs_fattr *fattr, FILE_UNIX_BASIC_INFO *info, * junction to the new submount (ie to setup the fake directory * which represents a DFS referral). */ -void +static void cifs_create_dfs_fattr(struct cifs_fattr *fattr, struct super_block *sb) { struct cifs_sb_info *cifs_sb = CIFS_SB(sb); @@ -388,7 +388,7 @@ static int cifs_sfu_mode(struct cifs_fattr *fattr, const unsigned char *path, } /* Fill a cifs_fattr struct with info from FILE_ALL_INFO */ -void +static void cifs_all_info_to_fattr(struct cifs_fattr *fattr, FILE_ALL_INFO *info, struct cifs_sb_info *cifs_sb, bool adjust_tz) { -- GitLab From 2ded9e2747d0a390d281bb5b16ff7f640ec85f78 Mon Sep 17 00:00:00 2001 From: "ling.ma@intel.com" Date: Thu, 16 Jul 2009 17:23:09 +0800 Subject: [PATCH 0224/1342] drm/i915: hdmi detection according by reading edid According to investigations from windows team ,hw team, and our test results on all 4x platofrms available (gm45, g45b, q45, g45a, g45c, g41a, and g41), we find currently Hot plug live status and Hot plug interrupt detection are not reliable, sometime the results from the two approaches are contradicts. So we chose edid detection for hdmi output. Signed-off-by: Ma Ling Reviewed-by: Ian Romanick Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_hdmi.c | 64 ++----------------------------- 1 file changed, 4 insertions(+), 60 deletions(-) diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c index 9e30daae37d..1842290cded 100644 --- a/drivers/gpu/drm/i915/intel_hdmi.c +++ b/drivers/gpu/drm/i915/intel_hdmi.c @@ -130,16 +130,17 @@ static bool intel_hdmi_mode_fixup(struct drm_encoder *encoder, } static enum drm_connector_status -intel_hdmi_edid_detect(struct drm_connector *connector) +intel_hdmi_detect(struct drm_connector *connector) { struct intel_output *intel_output = to_intel_output(connector); struct intel_hdmi_priv *hdmi_priv = intel_output->dev_priv; struct edid *edid = NULL; enum drm_connector_status status = connector_status_disconnected; + hdmi_priv->has_hdmi_sink = false; edid = drm_get_edid(&intel_output->base, intel_output->ddc_bus); - hdmi_priv->has_hdmi_sink = false; + if (edid) { if (edid->input & DRM_EDID_INPUT_DIGITAL) { status = connector_status_connected; @@ -148,65 +149,8 @@ intel_hdmi_edid_detect(struct drm_connector *connector) intel_output->base.display_info.raw_edid = NULL; kfree(edid); } - return status; -} - -static enum drm_connector_status -igdng_hdmi_detect(struct drm_connector *connector) -{ - struct intel_output *intel_output = to_intel_output(connector); - struct intel_hdmi_priv *hdmi_priv = intel_output->dev_priv; - - /* FIXME hotplug detect */ - - hdmi_priv->has_hdmi_sink = false; - return intel_hdmi_edid_detect(connector); -} -static enum drm_connector_status -intel_hdmi_detect(struct drm_connector *connector) -{ - struct drm_device *dev = connector->dev; - struct drm_i915_private *dev_priv = dev->dev_private; - struct intel_output *intel_output = to_intel_output(connector); - struct intel_hdmi_priv *hdmi_priv = intel_output->dev_priv; - u32 temp, bit; - - if (IS_IGDNG(dev)) - return igdng_hdmi_detect(connector); - - temp = I915_READ(PORT_HOTPLUG_EN); - - switch (hdmi_priv->sdvox_reg) { - case SDVOB: - temp |= HDMIB_HOTPLUG_INT_EN; - break; - case SDVOC: - temp |= HDMIC_HOTPLUG_INT_EN; - break; - default: - return connector_status_unknown; - } - - I915_WRITE(PORT_HOTPLUG_EN, temp); - - POSTING_READ(PORT_HOTPLUG_EN); - - switch (hdmi_priv->sdvox_reg) { - case SDVOB: - bit = HDMIB_HOTPLUG_INT_STATUS; - break; - case SDVOC: - bit = HDMIC_HOTPLUG_INT_STATUS; - break; - default: - return connector_status_unknown; - } - - if ((I915_READ(PORT_HOTPLUG_STAT) & bit) != 0) - return intel_hdmi_edid_detect(connector); - else - return connector_status_disconnected; + return status; } static int intel_hdmi_get_modes(struct drm_connector *connector) -- GitLab From 4be3bd7849165e7efa6b0b35a23d6a3598d97465 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Wed, 22 Jul 2009 19:32:59 -0700 Subject: [PATCH 0225/1342] Linux 2.6.31-rc4 --- Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Makefile b/Makefile index 79957b33877..063d738405e 100644 --- a/Makefile +++ b/Makefile @@ -1,7 +1,7 @@ VERSION = 2 PATCHLEVEL = 6 SUBLEVEL = 31 -EXTRAVERSION = -rc3 +EXTRAVERSION = -rc4 NAME = Man-Eating Seals of Antiquity # *DOCUMENTATION* -- GitLab From 1d3e216f1d303878d7204de94dee251bc2702175 Mon Sep 17 00:00:00 2001 From: Mike Rapoport Date: Tue, 21 Jul 2009 17:09:52 +0300 Subject: [PATCH 0226/1342] [ARM] pxa/em-x270: fix compile failure when CONFIG_APM_EMULATION=n If CONFIG_APM_EMULATION=n em-x270 build fails with linker error: arch/arm/mach-pxa/built-in.o: In function `em_x270_battery_critical': em-x270.c:(.text+0x12c0): undefined reference to `apm_queue_event' arch/arm/mach-pxa/built-in.o: In function `em_x270_battery_low': em-x270.c:(.text+0x12c8): undefined reference to `apm_queue_event' make: *** [.tmp_vmlinux1] Error 1 Fix it. Signed-off-by: Mike Rapoport Signed-off-by: Eric Miao --- arch/arm/mach-pxa/em-x270.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c index 63b10d9bb1d..9cd09465a0e 100644 --- a/arch/arm/mach-pxa/em-x270.c +++ b/arch/arm/mach-pxa/em-x270.c @@ -1141,12 +1141,16 @@ struct power_supply_info em_x270_psy_info = { static void em_x270_battery_low(void) { +#if defined(CONFIG_APM_EMULATION) apm_queue_event(APM_LOW_BATTERY); +#endif } static void em_x270_battery_critical(void) { +#if defined(CONFIG_APM_EMULATION) apm_queue_event(APM_CRITICAL_SUSPEND); +#endif } struct da9030_battery_info em_x270_batterty_info = { -- GitLab From e3d433040ee6077e33d4ad22e2f60a38b085786d Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Sun, 28 Jun 2009 09:26:20 -0700 Subject: [PATCH 0227/1342] drivers/dma/fsldma.c: Remove unnecessary semicolons Signed-off-by: Joe Perches Signed-off-by: Dan Williams --- drivers/dma/fsldma.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c index 6e60c77a145..ef87a898414 100644 --- a/drivers/dma/fsldma.c +++ b/drivers/dma/fsldma.c @@ -142,7 +142,7 @@ static int dma_is_idle(struct fsl_dma_chan *fsl_chan) static void dma_start(struct fsl_dma_chan *fsl_chan) { - u32 mr_set = 0;; + u32 mr_set = 0; if (fsl_chan->feature & FSL_DMA_CHAN_PAUSE_EXT) { DMA_OUT(fsl_chan, &fsl_chan->reg_base->bcr, 0, 32); -- GitLab From c019894efc9c9ba5939948caa78c133b1ec8ae63 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Sun, 28 Jun 2009 09:26:21 -0700 Subject: [PATCH 0228/1342] drivers/dma: Remove unnecessary semicolons Signed-off-by: Joe Perches Signed-off-by: Dan Williams --- drivers/dma/dmatest.c | 2 +- drivers/dma/mv_xor.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/dma/dmatest.c b/drivers/dma/dmatest.c index fb7da5141e9..cec1ec0b7d0 100644 --- a/drivers/dma/dmatest.c +++ b/drivers/dma/dmatest.c @@ -114,7 +114,7 @@ static void dmatest_init_srcs(u8 **bufs, unsigned int start, unsigned int len) buf[i] = PATTERN_SRC | (~i & PATTERN_COUNT_MASK); for ( ; i < start + len; i++) buf[i] = PATTERN_SRC | PATTERN_COPY - | (~i & PATTERN_COUNT_MASK);; + | (~i & PATTERN_COUNT_MASK); for ( ; i < test_buf_size; i++) buf[i] = PATTERN_SRC | (~i & PATTERN_COUNT_MASK); buf++; diff --git a/drivers/dma/mv_xor.c b/drivers/dma/mv_xor.c index ddab94f5122..3f23eabe09f 100644 --- a/drivers/dma/mv_xor.c +++ b/drivers/dma/mv_xor.c @@ -1176,7 +1176,7 @@ static int __devinit mv_xor_probe(struct platform_device *pdev) if (dma_has_cap(DMA_MEMSET, dma_dev->cap_mask)) dma_dev->device_prep_dma_memset = mv_xor_prep_dma_memset; if (dma_has_cap(DMA_XOR, dma_dev->cap_mask)) { - dma_dev->max_xor = 8; ; + dma_dev->max_xor = 8; dma_dev->device_prep_dma_xor = mv_xor_prep_dma_xor; } -- GitLab From 0a2ff57d6fba92842272889b4bca447344cd9d36 Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Fri, 3 Jul 2009 19:26:51 +0200 Subject: [PATCH 0229/1342] dmaengine: dmatest: add a maximum number of test iterations The dmatest usually waits for the killing of its kthreads to stop running tests. This patch adds a parameter that sets a maximum number of test iterations. This feature is quite interesting for debugging when you set a lot of traces in your dmaengine controller driver. Signed-off-by: Nicolas Ferre Cc: Haavard Skinnemoen Acked-by: Maciej Sosnowski Signed-off-by: Andrew Morton Signed-off-by: Dan Williams --- drivers/dma/dmatest.c | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-) diff --git a/drivers/dma/dmatest.c b/drivers/dma/dmatest.c index cec1ec0b7d0..2d973d60e7b 100644 --- a/drivers/dma/dmatest.c +++ b/drivers/dma/dmatest.c @@ -38,6 +38,11 @@ module_param(max_channels, uint, S_IRUGO); MODULE_PARM_DESC(max_channels, "Maximum number of channels to use (default: all)"); +static unsigned int iterations; +module_param(iterations, uint, S_IRUGO); +MODULE_PARM_DESC(iterations, + "Iterations before stopping test (default: infinite)"); + static unsigned int xor_sources = 3; module_param(xor_sources, uint, S_IRUGO); MODULE_PARM_DESC(xor_sources, @@ -270,7 +275,8 @@ static int dmatest_func(void *data) flags = DMA_CTRL_ACK | DMA_COMPL_SKIP_DEST_UNMAP | DMA_PREP_INTERRUPT; - while (!kthread_should_stop()) { + while (!kthread_should_stop() + && !(iterations && total_tests >= iterations)) { struct dma_device *dev = chan->device; struct dma_async_tx_descriptor *tx = NULL; dma_addr_t dma_srcs[src_cnt]; @@ -416,6 +422,13 @@ err_srcbuf: err_srcs: pr_notice("%s: terminating after %u tests, %u failures (status %d)\n", thread_name, total_tests, failed_tests, ret); + + if (iterations > 0) + while (!kthread_should_stop()) { + DECLARE_WAIT_QUEUE_HEAD(wait_dmatest_exit); + interruptible_sleep_on(&wait_dmatest_exit); + } + return ret; } -- GitLab From f1aef8b6e6abf32a3a269542f95a19e2cb319f6c Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Mon, 6 Jul 2009 18:19:44 +0200 Subject: [PATCH 0230/1342] dmaengine: dmatest: correct thread_count while using multiple thread per channel It seems that thread_count is not properly calculated in dmatest. In fact the thread count number that is returned from dmatest_add_threads() is not correctly added to the thread_count and thus not properly printed. Signed-off-by: Nicolas Ferre Acked-by: Haavard Skinnemoen Acked-by: Maciej Sosnowski Signed-off-by: Andrew Morton Signed-off-by: Dan Williams --- drivers/dma/dmatest.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/dma/dmatest.c b/drivers/dma/dmatest.c index 2d973d60e7b..d93017fc787 100644 --- a/drivers/dma/dmatest.c +++ b/drivers/dma/dmatest.c @@ -508,11 +508,11 @@ static int dmatest_add_channel(struct dma_chan *chan) if (dma_has_cap(DMA_MEMCPY, dma_dev->cap_mask)) { cnt = dmatest_add_threads(dtc, DMA_MEMCPY); - thread_count += cnt > 0 ?: 0; + thread_count += cnt > 0 ? cnt : 0; } if (dma_has_cap(DMA_XOR, dma_dev->cap_mask)) { cnt = dmatest_add_threads(dtc, DMA_XOR); - thread_count += cnt > 0 ?: 0; + thread_count += cnt > 0 ? cnt : 0; } pr_info("dmatest: Started %u threads using %s\n", -- GitLab From dc78baa2b90b289590911b40b6800f77d0dc935a Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Fri, 3 Jul 2009 19:24:33 +0200 Subject: [PATCH 0231/1342] dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on at91sam9rl chip. It will be used on other products in the future. This first release covers only the memory-to-memory tranfer type. This is the only tranfer type supported by this chip. On other products, it will be used also for peripheral DMA transfer (slave API support to come). I used dmatest client without problem in different configurations to test it. Full documentation for this controller can be found in the SAM9RL datasheet: http://www.atmel.com/dyn/products/product_card.asp?part_id=4243 Signed-off-by: Nicolas Ferre Acked-by: Maciej Sosnowski Signed-off-by: Dan Williams --- arch/arm/mach-at91/include/mach/at_hdmac.h | 26 + drivers/dma/Kconfig | 8 + drivers/dma/Makefile | 1 + drivers/dma/at_hdmac.c | 1009 ++++++++++++++++++++ drivers/dma/at_hdmac_regs.h | 386 ++++++++ 5 files changed, 1430 insertions(+) create mode 100644 arch/arm/mach-at91/include/mach/at_hdmac.h create mode 100644 drivers/dma/at_hdmac.c create mode 100644 drivers/dma/at_hdmac_regs.h diff --git a/arch/arm/mach-at91/include/mach/at_hdmac.h b/arch/arm/mach-at91/include/mach/at_hdmac.h new file mode 100644 index 00000000000..21a5554f9cb --- /dev/null +++ b/arch/arm/mach-at91/include/mach/at_hdmac.h @@ -0,0 +1,26 @@ +/* + * Header file for the Atmel AHB DMA Controller driver + * + * Copyright (C) 2008 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ +#ifndef AT_HDMAC_H +#define AT_HDMAC_H + +#include + +/** + * struct at_dma_platform_data - Controller configuration parameters + * @nr_channels: Number of channels supported by hardware (max 8) + * @cap_mask: dma_capability flags supported by the platform + */ +struct at_dma_platform_data { + unsigned int nr_channels; + dma_cap_mask_t cap_mask; +}; + +#endif /* AT_HDMAC_H */ diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig index babf214a509..bc8fb41cd62 100644 --- a/drivers/dma/Kconfig +++ b/drivers/dma/Kconfig @@ -46,6 +46,14 @@ config DW_DMAC Support the Synopsys DesignWare AHB DMA controller. This can be integrated in chips such as the Atmel AT32ap7000. +config AT_HDMAC + tristate "Atmel AHB DMA support" + depends on ARCH_AT91SAM9RL + select DMA_ENGINE + help + Support the Atmel AHB DMA controller. This can be integrated in + chips such as the Atmel AT91SAM9RL. + config FSL_DMA tristate "Freescale Elo and Elo Plus DMA support" depends on FSL_SOC diff --git a/drivers/dma/Makefile b/drivers/dma/Makefile index 2e5dc96700d..d7bc5fd17d8 100644 --- a/drivers/dma/Makefile +++ b/drivers/dma/Makefile @@ -7,4 +7,5 @@ obj-$(CONFIG_INTEL_IOP_ADMA) += iop-adma.o obj-$(CONFIG_FSL_DMA) += fsldma.o obj-$(CONFIG_MV_XOR) += mv_xor.o obj-$(CONFIG_DW_DMAC) += dw_dmac.o +obj-$(CONFIG_AT_HDMAC) += at_hdmac.o obj-$(CONFIG_MX3_IPU) += ipu/ diff --git a/drivers/dma/at_hdmac.c b/drivers/dma/at_hdmac.c new file mode 100644 index 00000000000..64dbf0ce128 --- /dev/null +++ b/drivers/dma/at_hdmac.c @@ -0,0 +1,1009 @@ +/* + * Driver for the Atmel AHB DMA Controller (aka HDMA or DMAC on AT91 systems) + * + * Copyright (C) 2008 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * + * This supports the Atmel AHB DMA Controller, + * + * The driver has currently been tested with the Atmel AT91SAM9RL + * and AT91SAM9G45 series. + */ + +#include +#include +#include +#include +#include +#include +#include + +#include "at_hdmac_regs.h" + +/* + * Glossary + * -------- + * + * at_hdmac : Name of the ATmel AHB DMA Controller + * at_dma_ / atdma : ATmel DMA controller entity related + * atc_ / atchan : ATmel DMA Channel entity related + */ + +#define ATC_DEFAULT_CFG (ATC_FIFOCFG_HALFFIFO) +#define ATC_DEFAULT_CTRLA (0) +#define ATC_DEFAULT_CTRLB (ATC_SIF(0) \ + |ATC_DIF(1)) + +/* + * Initial number of descriptors to allocate for each channel. This could + * be increased during dma usage. + */ +static unsigned int init_nr_desc_per_channel = 64; +module_param(init_nr_desc_per_channel, uint, 0644); +MODULE_PARM_DESC(init_nr_desc_per_channel, + "initial descriptors per channel (default: 64)"); + + +/* prototypes */ +static dma_cookie_t atc_tx_submit(struct dma_async_tx_descriptor *tx); + + +/*----------------------------------------------------------------------*/ + +static struct at_desc *atc_first_active(struct at_dma_chan *atchan) +{ + return list_first_entry(&atchan->active_list, + struct at_desc, desc_node); +} + +static struct at_desc *atc_first_queued(struct at_dma_chan *atchan) +{ + return list_first_entry(&atchan->queue, + struct at_desc, desc_node); +} + +/** + * atc_alloc_descriptor - allocate and return an initilized descriptor + * @chan: the channel to allocate descriptors for + * @gfp_flags: GFP allocation flags + * + * Note: The ack-bit is positioned in the descriptor flag at creation time + * to make initial allocation more convenient. This bit will be cleared + * and control will be given to client at usage time (during + * preparation functions). + */ +static struct at_desc *atc_alloc_descriptor(struct dma_chan *chan, + gfp_t gfp_flags) +{ + struct at_desc *desc = NULL; + struct at_dma *atdma = to_at_dma(chan->device); + dma_addr_t phys; + + desc = dma_pool_alloc(atdma->dma_desc_pool, gfp_flags, &phys); + if (desc) { + memset(desc, 0, sizeof(struct at_desc)); + dma_async_tx_descriptor_init(&desc->txd, chan); + /* txd.flags will be overwritten in prep functions */ + desc->txd.flags = DMA_CTRL_ACK; + desc->txd.tx_submit = atc_tx_submit; + desc->txd.phys = phys; + } + + return desc; +} + +/** + * atc_desc_get - get a unsused descriptor from free_list + * @atchan: channel we want a new descriptor for + */ +static struct at_desc *atc_desc_get(struct at_dma_chan *atchan) +{ + struct at_desc *desc, *_desc; + struct at_desc *ret = NULL; + unsigned int i = 0; + LIST_HEAD(tmp_list); + + spin_lock_bh(&atchan->lock); + list_for_each_entry_safe(desc, _desc, &atchan->free_list, desc_node) { + i++; + if (async_tx_test_ack(&desc->txd)) { + list_del(&desc->desc_node); + ret = desc; + break; + } + dev_dbg(chan2dev(&atchan->chan_common), + "desc %p not ACKed\n", desc); + } + spin_unlock_bh(&atchan->lock); + dev_vdbg(chan2dev(&atchan->chan_common), + "scanned %u descriptors on freelist\n", i); + + /* no more descriptor available in initial pool: create one more */ + if (!ret) { + ret = atc_alloc_descriptor(&atchan->chan_common, GFP_ATOMIC); + if (ret) { + spin_lock_bh(&atchan->lock); + atchan->descs_allocated++; + spin_unlock_bh(&atchan->lock); + } else { + dev_err(chan2dev(&atchan->chan_common), + "not enough descriptors available\n"); + } + } + + return ret; +} + +/** + * atc_desc_put - move a descriptor, including any children, to the free list + * @atchan: channel we work on + * @desc: descriptor, at the head of a chain, to move to free list + */ +static void atc_desc_put(struct at_dma_chan *atchan, struct at_desc *desc) +{ + if (desc) { + struct at_desc *child; + + spin_lock_bh(&atchan->lock); + list_for_each_entry(child, &desc->txd.tx_list, desc_node) + dev_vdbg(chan2dev(&atchan->chan_common), + "moving child desc %p to freelist\n", + child); + list_splice_init(&desc->txd.tx_list, &atchan->free_list); + dev_vdbg(chan2dev(&atchan->chan_common), + "moving desc %p to freelist\n", desc); + list_add(&desc->desc_node, &atchan->free_list); + spin_unlock_bh(&atchan->lock); + } +} + +/** + * atc_assign_cookie - compute and assign new cookie + * @atchan: channel we work on + * @desc: descriptor to asign cookie for + * + * Called with atchan->lock held and bh disabled + */ +static dma_cookie_t +atc_assign_cookie(struct at_dma_chan *atchan, struct at_desc *desc) +{ + dma_cookie_t cookie = atchan->chan_common.cookie; + + if (++cookie < 0) + cookie = 1; + + atchan->chan_common.cookie = cookie; + desc->txd.cookie = cookie; + + return cookie; +} + +/** + * atc_dostart - starts the DMA engine for real + * @atchan: the channel we want to start + * @first: first descriptor in the list we want to begin with + * + * Called with atchan->lock held and bh disabled + */ +static void atc_dostart(struct at_dma_chan *atchan, struct at_desc *first) +{ + struct at_dma *atdma = to_at_dma(atchan->chan_common.device); + + /* ASSERT: channel is idle */ + if (atc_chan_is_enabled(atchan)) { + dev_err(chan2dev(&atchan->chan_common), + "BUG: Attempted to start non-idle channel\n"); + dev_err(chan2dev(&atchan->chan_common), + " channel: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n", + channel_readl(atchan, SADDR), + channel_readl(atchan, DADDR), + channel_readl(atchan, CTRLA), + channel_readl(atchan, CTRLB), + channel_readl(atchan, DSCR)); + + /* The tasklet will hopefully advance the queue... */ + return; + } + + vdbg_dump_regs(atchan); + + /* clear any pending interrupt */ + while (dma_readl(atdma, EBCISR)) + cpu_relax(); + + channel_writel(atchan, SADDR, 0); + channel_writel(atchan, DADDR, 0); + channel_writel(atchan, CTRLA, 0); + channel_writel(atchan, CTRLB, 0); + channel_writel(atchan, DSCR, first->txd.phys); + dma_writel(atdma, CHER, atchan->mask); + + vdbg_dump_regs(atchan); +} + +/** + * atc_chain_complete - finish work for one transaction chain + * @atchan: channel we work on + * @desc: descriptor at the head of the chain we want do complete + * + * Called with atchan->lock held and bh disabled */ +static void +atc_chain_complete(struct at_dma_chan *atchan, struct at_desc *desc) +{ + dma_async_tx_callback callback; + void *param; + struct dma_async_tx_descriptor *txd = &desc->txd; + + dev_vdbg(chan2dev(&atchan->chan_common), + "descriptor %u complete\n", txd->cookie); + + atchan->completed_cookie = txd->cookie; + callback = txd->callback; + param = txd->callback_param; + + /* move children to free_list */ + list_splice_init(&txd->tx_list, &atchan->free_list); + /* move myself to free_list */ + list_move(&desc->desc_node, &atchan->free_list); + + /* unmap dma addresses */ + if (!(txd->flags & DMA_COMPL_SKIP_DEST_UNMAP)) { + if (txd->flags & DMA_COMPL_DEST_UNMAP_SINGLE) + dma_unmap_single(chan2parent(&atchan->chan_common), + desc->lli.daddr, + desc->len, DMA_FROM_DEVICE); + else + dma_unmap_page(chan2parent(&atchan->chan_common), + desc->lli.daddr, + desc->len, DMA_FROM_DEVICE); + } + if (!(txd->flags & DMA_COMPL_SKIP_SRC_UNMAP)) { + if (txd->flags & DMA_COMPL_SRC_UNMAP_SINGLE) + dma_unmap_single(chan2parent(&atchan->chan_common), + desc->lli.saddr, + desc->len, DMA_TO_DEVICE); + else + dma_unmap_page(chan2parent(&atchan->chan_common), + desc->lli.saddr, + desc->len, DMA_TO_DEVICE); + } + + /* + * The API requires that no submissions are done from a + * callback, so we don't need to drop the lock here + */ + if (callback) + callback(param); + + dma_run_dependencies(txd); +} + +/** + * atc_complete_all - finish work for all transactions + * @atchan: channel to complete transactions for + * + * Eventually submit queued descriptors if any + * + * Assume channel is idle while calling this function + * Called with atchan->lock held and bh disabled + */ +static void atc_complete_all(struct at_dma_chan *atchan) +{ + struct at_desc *desc, *_desc; + LIST_HEAD(list); + + dev_vdbg(chan2dev(&atchan->chan_common), "complete all\n"); + + BUG_ON(atc_chan_is_enabled(atchan)); + + /* + * Submit queued descriptors ASAP, i.e. before we go through + * the completed ones. + */ + if (!list_empty(&atchan->queue)) + atc_dostart(atchan, atc_first_queued(atchan)); + /* empty active_list now it is completed */ + list_splice_init(&atchan->active_list, &list); + /* empty queue list by moving descriptors (if any) to active_list */ + list_splice_init(&atchan->queue, &atchan->active_list); + + list_for_each_entry_safe(desc, _desc, &list, desc_node) + atc_chain_complete(atchan, desc); +} + +/** + * atc_cleanup_descriptors - cleanup up finished descriptors in active_list + * @atchan: channel to be cleaned up + * + * Called with atchan->lock held and bh disabled + */ +static void atc_cleanup_descriptors(struct at_dma_chan *atchan) +{ + struct at_desc *desc, *_desc; + struct at_desc *child; + + dev_vdbg(chan2dev(&atchan->chan_common), "cleanup descriptors\n"); + + list_for_each_entry_safe(desc, _desc, &atchan->active_list, desc_node) { + if (!(desc->lli.ctrla & ATC_DONE)) + /* This one is currently in progress */ + return; + + list_for_each_entry(child, &desc->txd.tx_list, desc_node) + if (!(child->lli.ctrla & ATC_DONE)) + /* Currently in progress */ + return; + + /* + * No descriptors so far seem to be in progress, i.e. + * this chain must be done. + */ + atc_chain_complete(atchan, desc); + } +} + +/** + * atc_advance_work - at the end of a transaction, move forward + * @atchan: channel where the transaction ended + * + * Called with atchan->lock held and bh disabled + */ +static void atc_advance_work(struct at_dma_chan *atchan) +{ + dev_vdbg(chan2dev(&atchan->chan_common), "advance_work\n"); + + if (list_empty(&atchan->active_list) || + list_is_singular(&atchan->active_list)) { + atc_complete_all(atchan); + } else { + atc_chain_complete(atchan, atc_first_active(atchan)); + /* advance work */ + atc_dostart(atchan, atc_first_active(atchan)); + } +} + + +/** + * atc_handle_error - handle errors reported by DMA controller + * @atchan: channel where error occurs + * + * Called with atchan->lock held and bh disabled + */ +static void atc_handle_error(struct at_dma_chan *atchan) +{ + struct at_desc *bad_desc; + struct at_desc *child; + + /* + * The descriptor currently at the head of the active list is + * broked. Since we don't have any way to report errors, we'll + * just have to scream loudly and try to carry on. + */ + bad_desc = atc_first_active(atchan); + list_del_init(&bad_desc->desc_node); + + /* As we are stopped, take advantage to push queued descriptors + * in active_list */ + list_splice_init(&atchan->queue, atchan->active_list.prev); + + /* Try to restart the controller */ + if (!list_empty(&atchan->active_list)) + atc_dostart(atchan, atc_first_active(atchan)); + + /* + * KERN_CRITICAL may seem harsh, but since this only happens + * when someone submits a bad physical address in a + * descriptor, we should consider ourselves lucky that the + * controller flagged an error instead of scribbling over + * random memory locations. + */ + dev_crit(chan2dev(&atchan->chan_common), + "Bad descriptor submitted for DMA!\n"); + dev_crit(chan2dev(&atchan->chan_common), + " cookie: %d\n", bad_desc->txd.cookie); + atc_dump_lli(atchan, &bad_desc->lli); + list_for_each_entry(child, &bad_desc->txd.tx_list, desc_node) + atc_dump_lli(atchan, &child->lli); + + /* Pretend the descriptor completed successfully */ + atc_chain_complete(atchan, bad_desc); +} + + +/*-- IRQ & Tasklet ---------------------------------------------------*/ + +static void atc_tasklet(unsigned long data) +{ + struct at_dma_chan *atchan = (struct at_dma_chan *)data; + + /* Channel cannot be enabled here */ + if (atc_chan_is_enabled(atchan)) { + dev_err(chan2dev(&atchan->chan_common), + "BUG: channel enabled in tasklet\n"); + return; + } + + spin_lock(&atchan->lock); + if (test_and_clear_bit(0, &atchan->error_status)) + atc_handle_error(atchan); + else + atc_advance_work(atchan); + + spin_unlock(&atchan->lock); +} + +static irqreturn_t at_dma_interrupt(int irq, void *dev_id) +{ + struct at_dma *atdma = (struct at_dma *)dev_id; + struct at_dma_chan *atchan; + int i; + u32 status, pending, imr; + int ret = IRQ_NONE; + + do { + imr = dma_readl(atdma, EBCIMR); + status = dma_readl(atdma, EBCISR); + pending = status & imr; + + if (!pending) + break; + + dev_vdbg(atdma->dma_common.dev, + "interrupt: status = 0x%08x, 0x%08x, 0x%08x\n", + status, imr, pending); + + for (i = 0; i < atdma->dma_common.chancnt; i++) { + atchan = &atdma->chan[i]; + if (pending & (AT_DMA_CBTC(i) | AT_DMA_ERR(i))) { + if (pending & AT_DMA_ERR(i)) { + /* Disable channel on AHB error */ + dma_writel(atdma, CHDR, atchan->mask); + /* Give information to tasklet */ + set_bit(0, &atchan->error_status); + } + tasklet_schedule(&atchan->tasklet); + ret = IRQ_HANDLED; + } + } + + } while (pending); + + return ret; +} + + +/*-- DMA Engine API --------------------------------------------------*/ + +/** + * atc_tx_submit - set the prepared descriptor(s) to be executed by the engine + * @desc: descriptor at the head of the transaction chain + * + * Queue chain if DMA engine is working already + * + * Cookie increment and adding to active_list or queue must be atomic + */ +static dma_cookie_t atc_tx_submit(struct dma_async_tx_descriptor *tx) +{ + struct at_desc *desc = txd_to_at_desc(tx); + struct at_dma_chan *atchan = to_at_dma_chan(tx->chan); + dma_cookie_t cookie; + + spin_lock_bh(&atchan->lock); + cookie = atc_assign_cookie(atchan, desc); + + if (list_empty(&atchan->active_list)) { + dev_vdbg(chan2dev(tx->chan), "tx_submit: started %u\n", + desc->txd.cookie); + atc_dostart(atchan, desc); + list_add_tail(&desc->desc_node, &atchan->active_list); + } else { + dev_vdbg(chan2dev(tx->chan), "tx_submit: queued %u\n", + desc->txd.cookie); + list_add_tail(&desc->desc_node, &atchan->queue); + } + + spin_unlock_bh(&atchan->lock); + + return cookie; +} + +/** + * atc_prep_dma_memcpy - prepare a memcpy operation + * @chan: the channel to prepare operation on + * @dest: operation virtual destination address + * @src: operation virtual source address + * @len: operation length + * @flags: tx descriptor status flags + */ +static struct dma_async_tx_descriptor * +atc_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src, + size_t len, unsigned long flags) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + struct at_desc *desc = NULL; + struct at_desc *first = NULL; + struct at_desc *prev = NULL; + size_t xfer_count; + size_t offset; + unsigned int src_width; + unsigned int dst_width; + u32 ctrla; + u32 ctrlb; + + dev_vdbg(chan2dev(chan), "prep_dma_memcpy: d0x%x s0x%x l0x%zx f0x%lx\n", + dest, src, len, flags); + + if (unlikely(!len)) { + dev_dbg(chan2dev(chan), "prep_dma_memcpy: length is zero!\n"); + return NULL; + } + + ctrla = ATC_DEFAULT_CTRLA; + ctrlb = ATC_DEFAULT_CTRLB + | ATC_SRC_ADDR_MODE_INCR + | ATC_DST_ADDR_MODE_INCR + | ATC_FC_MEM2MEM; + + /* + * We can be a lot more clever here, but this should take care + * of the most common optimization. + */ + if (!((src | dest | len) & 3)) { + ctrla |= ATC_SRC_WIDTH_WORD | ATC_DST_WIDTH_WORD; + src_width = dst_width = 2; + } else if (!((src | dest | len) & 1)) { + ctrla |= ATC_SRC_WIDTH_HALFWORD | ATC_DST_WIDTH_HALFWORD; + src_width = dst_width = 1; + } else { + ctrla |= ATC_SRC_WIDTH_BYTE | ATC_DST_WIDTH_BYTE; + src_width = dst_width = 0; + } + + for (offset = 0; offset < len; offset += xfer_count << src_width) { + xfer_count = min_t(size_t, (len - offset) >> src_width, + ATC_BTSIZE_MAX); + + desc = atc_desc_get(atchan); + if (!desc) + goto err_desc_get; + + desc->lli.saddr = src + offset; + desc->lli.daddr = dest + offset; + desc->lli.ctrla = ctrla | xfer_count; + desc->lli.ctrlb = ctrlb; + + desc->txd.cookie = 0; + async_tx_ack(&desc->txd); + + if (!first) { + first = desc; + } else { + /* inform the HW lli about chaining */ + prev->lli.dscr = desc->txd.phys; + /* insert the link descriptor to the LD ring */ + list_add_tail(&desc->desc_node, + &first->txd.tx_list); + } + prev = desc; + } + + /* First descriptor of the chain embedds additional information */ + first->txd.cookie = -EBUSY; + first->len = len; + + /* set end-of-link to the last link descriptor of list*/ + set_desc_eol(desc); + + desc->txd.flags = flags; /* client is in control of this ack */ + + return &first->txd; + +err_desc_get: + atc_desc_put(atchan, first); + return NULL; +} + +/** + * atc_is_tx_complete - poll for transaction completion + * @chan: DMA channel + * @cookie: transaction identifier to check status of + * @done: if not %NULL, updated with last completed transaction + * @used: if not %NULL, updated with last used transaction + * + * If @done and @used are passed in, upon return they reflect the driver + * internal state and can be used with dma_async_is_complete() to check + * the status of multiple cookies without re-checking hardware state. + */ +static enum dma_status +atc_is_tx_complete(struct dma_chan *chan, + dma_cookie_t cookie, + dma_cookie_t *done, dma_cookie_t *used) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + dma_cookie_t last_used; + dma_cookie_t last_complete; + enum dma_status ret; + + dev_vdbg(chan2dev(chan), "is_tx_complete: %d (d%d, u%d)\n", + cookie, done ? *done : 0, used ? *used : 0); + + spin_lock_bh(atchan->lock); + + last_complete = atchan->completed_cookie; + last_used = chan->cookie; + + ret = dma_async_is_complete(cookie, last_complete, last_used); + if (ret != DMA_SUCCESS) { + atc_cleanup_descriptors(atchan); + + last_complete = atchan->completed_cookie; + last_used = chan->cookie; + + ret = dma_async_is_complete(cookie, last_complete, last_used); + } + + spin_unlock_bh(atchan->lock); + + if (done) + *done = last_complete; + if (used) + *used = last_used; + + return ret; +} + +/** + * atc_issue_pending - try to finish work + * @chan: target DMA channel + */ +static void atc_issue_pending(struct dma_chan *chan) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + + dev_vdbg(chan2dev(chan), "issue_pending\n"); + + if (!atc_chan_is_enabled(atchan)) { + spin_lock_bh(&atchan->lock); + atc_advance_work(atchan); + spin_unlock_bh(&atchan->lock); + } +} + +/** + * atc_alloc_chan_resources - allocate resources for DMA channel + * @chan: allocate descriptor resources for this channel + * @client: current client requesting the channel be ready for requests + * + * return - the number of allocated descriptors + */ +static int atc_alloc_chan_resources(struct dma_chan *chan) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + struct at_dma *atdma = to_at_dma(chan->device); + struct at_desc *desc; + int i; + LIST_HEAD(tmp_list); + + dev_vdbg(chan2dev(chan), "alloc_chan_resources\n"); + + /* ASSERT: channel is idle */ + if (atc_chan_is_enabled(atchan)) { + dev_dbg(chan2dev(chan), "DMA channel not idle ?\n"); + return -EIO; + } + + /* have we already been set up? */ + if (!list_empty(&atchan->free_list)) + return atchan->descs_allocated; + + /* Allocate initial pool of descriptors */ + for (i = 0; i < init_nr_desc_per_channel; i++) { + desc = atc_alloc_descriptor(chan, GFP_KERNEL); + if (!desc) { + dev_err(atdma->dma_common.dev, + "Only %d initial descriptors\n", i); + break; + } + list_add_tail(&desc->desc_node, &tmp_list); + } + + spin_lock_bh(&atchan->lock); + atchan->descs_allocated = i; + list_splice(&tmp_list, &atchan->free_list); + atchan->completed_cookie = chan->cookie = 1; + spin_unlock_bh(&atchan->lock); + + /* channel parameters */ + channel_writel(atchan, CFG, ATC_DEFAULT_CFG); + + dev_dbg(chan2dev(chan), + "alloc_chan_resources: allocated %d descriptors\n", + atchan->descs_allocated); + + return atchan->descs_allocated; +} + +/** + * atc_free_chan_resources - free all channel resources + * @chan: DMA channel + */ +static void atc_free_chan_resources(struct dma_chan *chan) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + struct at_dma *atdma = to_at_dma(chan->device); + struct at_desc *desc, *_desc; + LIST_HEAD(list); + + dev_dbg(chan2dev(chan), "free_chan_resources: (descs allocated=%u)\n", + atchan->descs_allocated); + + /* ASSERT: channel is idle */ + BUG_ON(!list_empty(&atchan->active_list)); + BUG_ON(!list_empty(&atchan->queue)); + BUG_ON(atc_chan_is_enabled(atchan)); + + list_for_each_entry_safe(desc, _desc, &atchan->free_list, desc_node) { + dev_vdbg(chan2dev(chan), " freeing descriptor %p\n", desc); + list_del(&desc->desc_node); + /* free link descriptor */ + dma_pool_free(atdma->dma_desc_pool, desc, desc->txd.phys); + } + list_splice_init(&atchan->free_list, &list); + atchan->descs_allocated = 0; + + dev_vdbg(chan2dev(chan), "free_chan_resources: done\n"); +} + + +/*-- Module Management -----------------------------------------------*/ + +/** + * at_dma_off - disable DMA controller + * @atdma: the Atmel HDAMC device + */ +static void at_dma_off(struct at_dma *atdma) +{ + dma_writel(atdma, EN, 0); + + /* disable all interrupts */ + dma_writel(atdma, EBCIDR, -1L); + + /* confirm that all channels are disabled */ + while (dma_readl(atdma, CHSR) & atdma->all_chan_mask) + cpu_relax(); +} + +static int __init at_dma_probe(struct platform_device *pdev) +{ + struct at_dma_platform_data *pdata; + struct resource *io; + struct at_dma *atdma; + size_t size; + int irq; + int err; + int i; + + /* get DMA Controller parameters from platform */ + pdata = pdev->dev.platform_data; + if (!pdata || pdata->nr_channels > AT_DMA_MAX_NR_CHANNELS) + return -EINVAL; + + io = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!io) + return -EINVAL; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) + return irq; + + size = sizeof(struct at_dma); + size += pdata->nr_channels * sizeof(struct at_dma_chan); + atdma = kzalloc(size, GFP_KERNEL); + if (!atdma) + return -ENOMEM; + + /* discover transaction capabilites from the platform data */ + atdma->dma_common.cap_mask = pdata->cap_mask; + atdma->all_chan_mask = (1 << pdata->nr_channels) - 1; + + size = io->end - io->start + 1; + if (!request_mem_region(io->start, size, pdev->dev.driver->name)) { + err = -EBUSY; + goto err_kfree; + } + + atdma->regs = ioremap(io->start, size); + if (!atdma->regs) { + err = -ENOMEM; + goto err_release_r; + } + + atdma->clk = clk_get(&pdev->dev, "dma_clk"); + if (IS_ERR(atdma->clk)) { + err = PTR_ERR(atdma->clk); + goto err_clk; + } + clk_enable(atdma->clk); + + /* force dma off, just in case */ + at_dma_off(atdma); + + err = request_irq(irq, at_dma_interrupt, 0, "at_hdmac", atdma); + if (err) + goto err_irq; + + platform_set_drvdata(pdev, atdma); + + /* create a pool of consistent memory blocks for hardware descriptors */ + atdma->dma_desc_pool = dma_pool_create("at_hdmac_desc_pool", + &pdev->dev, sizeof(struct at_desc), + 4 /* word alignment */, 0); + if (!atdma->dma_desc_pool) { + dev_err(&pdev->dev, "No memory for descriptors dma pool\n"); + err = -ENOMEM; + goto err_pool_create; + } + + /* clear any pending interrupt */ + while (dma_readl(atdma, EBCISR)) + cpu_relax(); + + /* initialize channels related values */ + INIT_LIST_HEAD(&atdma->dma_common.channels); + for (i = 0; i < pdata->nr_channels; i++, atdma->dma_common.chancnt++) { + struct at_dma_chan *atchan = &atdma->chan[i]; + + atchan->chan_common.device = &atdma->dma_common; + atchan->chan_common.cookie = atchan->completed_cookie = 1; + atchan->chan_common.chan_id = i; + list_add_tail(&atchan->chan_common.device_node, + &atdma->dma_common.channels); + + atchan->ch_regs = atdma->regs + ch_regs(i); + spin_lock_init(&atchan->lock); + atchan->mask = 1 << i; + + INIT_LIST_HEAD(&atchan->active_list); + INIT_LIST_HEAD(&atchan->queue); + INIT_LIST_HEAD(&atchan->free_list); + + tasklet_init(&atchan->tasklet, atc_tasklet, + (unsigned long)atchan); + atc_enable_irq(atchan); + } + + /* set base routines */ + atdma->dma_common.device_alloc_chan_resources = atc_alloc_chan_resources; + atdma->dma_common.device_free_chan_resources = atc_free_chan_resources; + atdma->dma_common.device_is_tx_complete = atc_is_tx_complete; + atdma->dma_common.device_issue_pending = atc_issue_pending; + atdma->dma_common.dev = &pdev->dev; + + /* set prep routines based on capability */ + if (dma_has_cap(DMA_MEMCPY, atdma->dma_common.cap_mask)) + atdma->dma_common.device_prep_dma_memcpy = atc_prep_dma_memcpy; + + dma_writel(atdma, EN, AT_DMA_ENABLE); + + dev_info(&pdev->dev, "Atmel AHB DMA Controller ( %s%s), %d channels\n", + dma_has_cap(DMA_MEMCPY, atdma->dma_common.cap_mask) ? "cpy " : "", + dma_has_cap(DMA_SLAVE, atdma->dma_common.cap_mask) ? "slave " : "", + atdma->dma_common.chancnt); + + dma_async_device_register(&atdma->dma_common); + + return 0; + +err_pool_create: + platform_set_drvdata(pdev, NULL); + free_irq(platform_get_irq(pdev, 0), atdma); +err_irq: + clk_disable(atdma->clk); + clk_put(atdma->clk); +err_clk: + iounmap(atdma->regs); + atdma->regs = NULL; +err_release_r: + release_mem_region(io->start, size); +err_kfree: + kfree(atdma); + return err; +} + +static int __exit at_dma_remove(struct platform_device *pdev) +{ + struct at_dma *atdma = platform_get_drvdata(pdev); + struct dma_chan *chan, *_chan; + struct resource *io; + + at_dma_off(atdma); + dma_async_device_unregister(&atdma->dma_common); + + dma_pool_destroy(atdma->dma_desc_pool); + platform_set_drvdata(pdev, NULL); + free_irq(platform_get_irq(pdev, 0), atdma); + + list_for_each_entry_safe(chan, _chan, &atdma->dma_common.channels, + device_node) { + struct at_dma_chan *atchan = to_at_dma_chan(chan); + + /* Disable interrupts */ + atc_disable_irq(atchan); + tasklet_disable(&atchan->tasklet); + + tasklet_kill(&atchan->tasklet); + list_del(&chan->device_node); + } + + clk_disable(atdma->clk); + clk_put(atdma->clk); + + iounmap(atdma->regs); + atdma->regs = NULL; + + io = platform_get_resource(pdev, IORESOURCE_MEM, 0); + release_mem_region(io->start, io->end - io->start + 1); + + kfree(atdma); + + return 0; +} + +static void at_dma_shutdown(struct platform_device *pdev) +{ + struct at_dma *atdma = platform_get_drvdata(pdev); + + at_dma_off(platform_get_drvdata(pdev)); + clk_disable(atdma->clk); +} + +static int at_dma_suspend_late(struct platform_device *pdev, pm_message_t mesg) +{ + struct at_dma *atdma = platform_get_drvdata(pdev); + + at_dma_off(platform_get_drvdata(pdev)); + clk_disable(atdma->clk); + return 0; +} + +static int at_dma_resume_early(struct platform_device *pdev) +{ + struct at_dma *atdma = platform_get_drvdata(pdev); + + clk_enable(atdma->clk); + dma_writel(atdma, EN, AT_DMA_ENABLE); + return 0; + +} + +static struct platform_driver at_dma_driver = { + .remove = __exit_p(at_dma_remove), + .shutdown = at_dma_shutdown, + .suspend_late = at_dma_suspend_late, + .resume_early = at_dma_resume_early, + .driver = { + .name = "at_hdmac", + }, +}; + +static int __init at_dma_init(void) +{ + return platform_driver_probe(&at_dma_driver, at_dma_probe); +} +module_init(at_dma_init); + +static void __exit at_dma_exit(void) +{ + platform_driver_unregister(&at_dma_driver); +} +module_exit(at_dma_exit); + +MODULE_DESCRIPTION("Atmel AHB DMA Controller driver"); +MODULE_AUTHOR("Nicolas Ferre "); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:at_hdmac"); diff --git a/drivers/dma/at_hdmac_regs.h b/drivers/dma/at_hdmac_regs.h new file mode 100644 index 00000000000..ad2d4f402bf --- /dev/null +++ b/drivers/dma/at_hdmac_regs.h @@ -0,0 +1,386 @@ +/* + * Header file for the Atmel AHB DMA Controller driver + * + * Copyright (C) 2008 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ +#ifndef AT_HDMAC_REGS_H +#define AT_HDMAC_REGS_H + +#include + +#define AT_DMA_MAX_NR_CHANNELS 8 + + +#define AT_DMA_GCFG 0x00 /* Global Configuration Register */ +#define AT_DMA_IF_BIGEND(i) (0x1 << (i)) /* AHB-Lite Interface i in Big-endian mode */ +#define AT_DMA_ARB_CFG (0x1 << 4) /* Arbiter mode. */ +#define AT_DMA_ARB_CFG_FIXED (0x0 << 4) +#define AT_DMA_ARB_CFG_ROUND_ROBIN (0x1 << 4) + +#define AT_DMA_EN 0x04 /* Controller Enable Register */ +#define AT_DMA_ENABLE (0x1 << 0) + +#define AT_DMA_SREQ 0x08 /* Software Single Request Register */ +#define AT_DMA_SSREQ(x) (0x1 << ((x) << 1)) /* Request a source single transfer on channel x */ +#define AT_DMA_DSREQ(x) (0x1 << (1 + ((x) << 1))) /* Request a destination single transfer on channel x */ + +#define AT_DMA_CREQ 0x0C /* Software Chunk Transfer Request Register */ +#define AT_DMA_SCREQ(x) (0x1 << ((x) << 1)) /* Request a source chunk transfer on channel x */ +#define AT_DMA_DCREQ(x) (0x1 << (1 + ((x) << 1))) /* Request a destination chunk transfer on channel x */ + +#define AT_DMA_LAST 0x10 /* Software Last Transfer Flag Register */ +#define AT_DMA_SLAST(x) (0x1 << ((x) << 1)) /* This src rq is last tx of buffer on channel x */ +#define AT_DMA_DLAST(x) (0x1 << (1 + ((x) << 1))) /* This dst rq is last tx of buffer on channel x */ + +#define AT_DMA_SYNC 0x14 /* Request Synchronization Register */ +#define AT_DMA_SYR(h) (0x1 << (h)) /* Synchronize handshake line h */ + +/* Error, Chained Buffer transfer completed and Buffer transfer completed Interrupt registers */ +#define AT_DMA_EBCIER 0x18 /* Enable register */ +#define AT_DMA_EBCIDR 0x1C /* Disable register */ +#define AT_DMA_EBCIMR 0x20 /* Mask Register */ +#define AT_DMA_EBCISR 0x24 /* Status Register */ +#define AT_DMA_CBTC_OFFSET 8 +#define AT_DMA_ERR_OFFSET 16 +#define AT_DMA_BTC(x) (0x1 << (x)) +#define AT_DMA_CBTC(x) (0x1 << (AT_DMA_CBTC_OFFSET + (x))) +#define AT_DMA_ERR(x) (0x1 << (AT_DMA_ERR_OFFSET + (x))) + +#define AT_DMA_CHER 0x28 /* Channel Handler Enable Register */ +#define AT_DMA_ENA(x) (0x1 << (x)) +#define AT_DMA_SUSP(x) (0x1 << ( 8 + (x))) +#define AT_DMA_KEEP(x) (0x1 << (24 + (x))) + +#define AT_DMA_CHDR 0x2C /* Channel Handler Disable Register */ +#define AT_DMA_DIS(x) (0x1 << (x)) +#define AT_DMA_RES(x) (0x1 << ( 8 + (x))) + +#define AT_DMA_CHSR 0x30 /* Channel Handler Status Register */ +#define AT_DMA_EMPT(x) (0x1 << (16 + (x))) +#define AT_DMA_STAL(x) (0x1 << (24 + (x))) + + +#define AT_DMA_CH_REGS_BASE 0x3C /* Channel registers base address */ +#define ch_regs(x) (AT_DMA_CH_REGS_BASE + (x) * 0x28) /* Channel x base addr */ + +/* Hardware register offset for each channel */ +#define ATC_SADDR_OFFSET 0x00 /* Source Address Register */ +#define ATC_DADDR_OFFSET 0x04 /* Destination Address Register */ +#define ATC_DSCR_OFFSET 0x08 /* Descriptor Address Register */ +#define ATC_CTRLA_OFFSET 0x0C /* Control A Register */ +#define ATC_CTRLB_OFFSET 0x10 /* Control B Register */ +#define ATC_CFG_OFFSET 0x14 /* Configuration Register */ +#define ATC_SPIP_OFFSET 0x18 /* Src PIP Configuration Register */ +#define ATC_DPIP_OFFSET 0x1C /* Dst PIP Configuration Register */ + + +/* Bitfield definitions */ + +/* Bitfields in DSCR */ +#define ATC_DSCR_IF(i) (0x3 & (i)) /* Dsc feched via AHB-Lite Interface i */ + +/* Bitfields in CTRLA */ +#define ATC_BTSIZE_MAX 0xFFFFUL /* Maximum Buffer Transfer Size */ +#define ATC_BTSIZE(x) (ATC_BTSIZE_MAX & (x)) /* Buffer Transfer Size */ +#define ATC_SCSIZE_MASK (0x7 << 16) /* Source Chunk Transfer Size */ +#define ATC_SCSIZE_1 (0x0 << 16) +#define ATC_SCSIZE_4 (0x1 << 16) +#define ATC_SCSIZE_8 (0x2 << 16) +#define ATC_SCSIZE_16 (0x3 << 16) +#define ATC_SCSIZE_32 (0x4 << 16) +#define ATC_SCSIZE_64 (0x5 << 16) +#define ATC_SCSIZE_128 (0x6 << 16) +#define ATC_SCSIZE_256 (0x7 << 16) +#define ATC_DCSIZE_MASK (0x7 << 20) /* Destination Chunk Transfer Size */ +#define ATC_DCSIZE_1 (0x0 << 20) +#define ATC_DCSIZE_4 (0x1 << 20) +#define ATC_DCSIZE_8 (0x2 << 20) +#define ATC_DCSIZE_16 (0x3 << 20) +#define ATC_DCSIZE_32 (0x4 << 20) +#define ATC_DCSIZE_64 (0x5 << 20) +#define ATC_DCSIZE_128 (0x6 << 20) +#define ATC_DCSIZE_256 (0x7 << 20) +#define ATC_SRC_WIDTH_MASK (0x3 << 24) /* Source Single Transfer Size */ +#define ATC_SRC_WIDTH_BYTE (0x0 << 24) +#define ATC_SRC_WIDTH_HALFWORD (0x1 << 24) +#define ATC_SRC_WIDTH_WORD (0x2 << 24) +#define ATC_DST_WIDTH_MASK (0x3 << 28) /* Destination Single Transfer Size */ +#define ATC_DST_WIDTH_BYTE (0x0 << 28) +#define ATC_DST_WIDTH_HALFWORD (0x1 << 28) +#define ATC_DST_WIDTH_WORD (0x2 << 28) +#define ATC_DONE (0x1 << 31) /* Tx Done (only written back in descriptor) */ + +/* Bitfields in CTRLB */ +#define ATC_SIF(i) (0x3 & (i)) /* Src tx done via AHB-Lite Interface i */ +#define ATC_DIF(i) ((0x3 & (i)) << 4) /* Dst tx done via AHB-Lite Interface i */ +#define ATC_SRC_PIP (0x1 << 8) /* Source Picture-in-Picture enabled */ +#define ATC_DST_PIP (0x1 << 12) /* Destination Picture-in-Picture enabled */ +#define ATC_SRC_DSCR_DIS (0x1 << 16) /* Src Descriptor fetch disable */ +#define ATC_DST_DSCR_DIS (0x1 << 20) /* Dst Descriptor fetch disable */ +#define ATC_FC_MASK (0x7 << 21) /* Choose Flow Controller */ +#define ATC_FC_MEM2MEM (0x0 << 21) /* Mem-to-Mem (DMA) */ +#define ATC_FC_MEM2PER (0x1 << 21) /* Mem-to-Periph (DMA) */ +#define ATC_FC_PER2MEM (0x2 << 21) /* Periph-to-Mem (DMA) */ +#define ATC_FC_PER2PER (0x3 << 21) /* Periph-to-Periph (DMA) */ +#define ATC_FC_PER2MEM_PER (0x4 << 21) /* Periph-to-Mem (Peripheral) */ +#define ATC_FC_MEM2PER_PER (0x5 << 21) /* Mem-to-Periph (Peripheral) */ +#define ATC_FC_PER2PER_PER (0x6 << 21) /* Periph-to-Periph (Src Peripheral) */ +#define ATC_SRC_ADDR_MODE_MASK (0x3 << 24) +#define ATC_SRC_ADDR_MODE_INCR (0x0 << 24) /* Incrementing Mode */ +#define ATC_SRC_ADDR_MODE_DECR (0x1 << 24) /* Decrementing Mode */ +#define ATC_SRC_ADDR_MODE_FIXED (0x2 << 24) /* Fixed Mode */ +#define ATC_DST_ADDR_MODE_MASK (0x3 << 28) +#define ATC_DST_ADDR_MODE_INCR (0x0 << 28) /* Incrementing Mode */ +#define ATC_DST_ADDR_MODE_DECR (0x1 << 28) /* Decrementing Mode */ +#define ATC_DST_ADDR_MODE_FIXED (0x2 << 28) /* Fixed Mode */ +#define ATC_IEN (0x1 << 30) /* BTC interrupt enable (active low) */ +#define ATC_AUTO (0x1 << 31) /* Auto multiple buffer tx enable */ + +/* Bitfields in CFG */ +#define ATC_SRC_PER(h) (0xFU & (h)) /* Channel src rq associated with periph handshaking ifc h */ +#define ATC_DST_PER(h) ((0xFU & (h)) << 4) /* Channel dst rq associated with periph handshaking ifc h */ +#define ATC_SRC_REP (0x1 << 8) /* Source Replay Mod */ +#define ATC_SRC_H2SEL (0x1 << 9) /* Source Handshaking Mod */ +#define ATC_SRC_H2SEL_SW (0x0 << 9) +#define ATC_SRC_H2SEL_HW (0x1 << 9) +#define ATC_DST_REP (0x1 << 12) /* Destination Replay Mod */ +#define ATC_DST_H2SEL (0x1 << 13) /* Destination Handshaking Mod */ +#define ATC_DST_H2SEL_SW (0x0 << 13) +#define ATC_DST_H2SEL_HW (0x1 << 13) +#define ATC_SOD (0x1 << 16) /* Stop On Done */ +#define ATC_LOCK_IF (0x1 << 20) /* Interface Lock */ +#define ATC_LOCK_B (0x1 << 21) /* AHB Bus Lock */ +#define ATC_LOCK_IF_L (0x1 << 22) /* Master Interface Arbiter Lock */ +#define ATC_LOCK_IF_L_CHUNK (0x0 << 22) +#define ATC_LOCK_IF_L_BUFFER (0x1 << 22) +#define ATC_AHB_PROT_MASK (0x7 << 24) /* AHB Protection */ +#define ATC_FIFOCFG_MASK (0x3 << 28) /* FIFO Request Configuration */ +#define ATC_FIFOCFG_LARGESTBURST (0x0 << 28) +#define ATC_FIFOCFG_HALFFIFO (0x1 << 28) +#define ATC_FIFOCFG_ENOUGHSPACE (0x2 << 28) + +/* Bitfields in SPIP */ +#define ATC_SPIP_HOLE(x) (0xFFFFU & (x)) +#define ATC_SPIP_BOUNDARY(x) ((0x3FF & (x)) << 16) + +/* Bitfields in DPIP */ +#define ATC_DPIP_HOLE(x) (0xFFFFU & (x)) +#define ATC_DPIP_BOUNDARY(x) ((0x3FF & (x)) << 16) + + +/*-- descriptors -----------------------------------------------------*/ + +/* LLI == Linked List Item; aka DMA buffer descriptor */ +struct at_lli { + /* values that are not changed by hardware */ + dma_addr_t saddr; + dma_addr_t daddr; + /* value that may get written back: */ + u32 ctrla; + /* more values that are not changed by hardware */ + u32 ctrlb; + dma_addr_t dscr; /* chain to next lli */ +}; + +/** + * struct at_desc - software descriptor + * @at_lli: hardware lli structure + * @txd: support for the async_tx api + * @desc_node: node on the channed descriptors list + * @len: total transaction bytecount + */ +struct at_desc { + /* FIRST values the hardware uses */ + struct at_lli lli; + + /* THEN values for driver housekeeping */ + struct dma_async_tx_descriptor txd; + struct list_head desc_node; + size_t len; +}; + +static inline struct at_desc * +txd_to_at_desc(struct dma_async_tx_descriptor *txd) +{ + return container_of(txd, struct at_desc, txd); +} + + +/*-- Channels --------------------------------------------------------*/ + +/** + * struct at_dma_chan - internal representation of an Atmel HDMAC channel + * @chan_common: common dmaengine channel object members + * @device: parent device + * @ch_regs: memory mapped register base + * @mask: channel index in a mask + * @error_status: transmit error status information from irq handler + * to tasklet (use atomic operations) + * @tasklet: bottom half to finish transaction work + * @lock: serializes enqueue/dequeue operations to descriptors lists + * @completed_cookie: identifier for the most recently completed operation + * @active_list: list of descriptors dmaengine is being running on + * @queue: list of descriptors ready to be submitted to engine + * @free_list: list of descriptors usable by the channel + * @descs_allocated: records the actual size of the descriptor pool + */ +struct at_dma_chan { + struct dma_chan chan_common; + struct at_dma *device; + void __iomem *ch_regs; + u8 mask; + unsigned long error_status; + struct tasklet_struct tasklet; + + spinlock_t lock; + + /* these other elements are all protected by lock */ + dma_cookie_t completed_cookie; + struct list_head active_list; + struct list_head queue; + struct list_head free_list; + unsigned int descs_allocated; +}; + +#define channel_readl(atchan, name) \ + __raw_readl((atchan)->ch_regs + ATC_##name##_OFFSET) + +#define channel_writel(atchan, name, val) \ + __raw_writel((val), (atchan)->ch_regs + ATC_##name##_OFFSET) + +static inline struct at_dma_chan *to_at_dma_chan(struct dma_chan *dchan) +{ + return container_of(dchan, struct at_dma_chan, chan_common); +} + + +/*-- Controller ------------------------------------------------------*/ + +/** + * struct at_dma - internal representation of an Atmel HDMA Controller + * @chan_common: common dmaengine dma_device object members + * @ch_regs: memory mapped register base + * @clk: dma controller clock + * @all_chan_mask: all channels availlable in a mask + * @dma_desc_pool: base of DMA descriptor region (DMA address) + * @chan: channels table to store at_dma_chan structures + */ +struct at_dma { + struct dma_device dma_common; + void __iomem *regs; + struct clk *clk; + + u8 all_chan_mask; + + struct dma_pool *dma_desc_pool; + /* AT THE END channels table */ + struct at_dma_chan chan[0]; +}; + +#define dma_readl(atdma, name) \ + __raw_readl((atdma)->regs + AT_DMA_##name) +#define dma_writel(atdma, name, val) \ + __raw_writel((val), (atdma)->regs + AT_DMA_##name) + +static inline struct at_dma *to_at_dma(struct dma_device *ddev) +{ + return container_of(ddev, struct at_dma, dma_common); +} + + +/*-- Helper functions ------------------------------------------------*/ + +static struct device *chan2dev(struct dma_chan *chan) +{ + return &chan->dev->device; +} +static struct device *chan2parent(struct dma_chan *chan) +{ + return chan->dev->device.parent; +} + +#if defined(VERBOSE_DEBUG) +static void vdbg_dump_regs(struct at_dma_chan *atchan) +{ + struct at_dma *atdma = to_at_dma(atchan->chan_common.device); + + dev_err(chan2dev(&atchan->chan_common), + " channel %d : imr = 0x%x, chsr = 0x%x\n", + atchan->chan_common.chan_id, + dma_readl(atdma, EBCIMR), + dma_readl(atdma, CHSR)); + + dev_err(chan2dev(&atchan->chan_common), + " channel: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n", + channel_readl(atchan, SADDR), + channel_readl(atchan, DADDR), + channel_readl(atchan, CTRLA), + channel_readl(atchan, CTRLB), + channel_readl(atchan, DSCR)); +} +#else +static void vdbg_dump_regs(struct at_dma_chan *atchan) {} +#endif + +static void atc_dump_lli(struct at_dma_chan *atchan, struct at_lli *lli) +{ + dev_printk(KERN_CRIT, chan2dev(&atchan->chan_common), + " desc: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n", + lli->saddr, lli->daddr, + lli->ctrla, lli->ctrlb, lli->dscr); +} + + +static void atc_setup_irq(struct at_dma_chan *atchan, int on) +{ + struct at_dma *atdma = to_at_dma(atchan->chan_common.device); + u32 ebci; + + /* enable interrupts on buffer chain completion & error */ + ebci = AT_DMA_CBTC(atchan->chan_common.chan_id) + | AT_DMA_ERR(atchan->chan_common.chan_id); + if (on) + dma_writel(atdma, EBCIER, ebci); + else + dma_writel(atdma, EBCIDR, ebci); +} + +static inline void atc_enable_irq(struct at_dma_chan *atchan) +{ + atc_setup_irq(atchan, 1); +} + +static inline void atc_disable_irq(struct at_dma_chan *atchan) +{ + atc_setup_irq(atchan, 0); +} + + +/** + * atc_chan_is_enabled - test if given channel is enabled + * @atchan: channel we want to test status + */ +static inline int atc_chan_is_enabled(struct at_dma_chan *atchan) +{ + struct at_dma *atdma = to_at_dma(atchan->chan_common.device); + + return !!(dma_readl(atdma, CHSR) & atchan->mask); +} + + +/** + * set_desc_eol - set end-of-link to descriptor so it will end transfer + * @desc: descriptor, signle or at the end of a chain, to end chain on + */ +static void set_desc_eol(struct at_desc *desc) +{ + desc->lli.ctrlb |= ATC_SRC_DSCR_DIS | ATC_DST_DSCR_DIS; + desc->lli.dscr = 0; +} + +#endif /* AT_HDMAC_REGS_H */ -- GitLab From 808347f6a31792079e345ec865e9cfcb6e8ae6b2 Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Wed, 22 Jul 2009 20:04:45 +0200 Subject: [PATCH 0232/1342] dmaengine: at_hdmac: add DMA slave transfers This patch for at_hdmac adds the slave transfers capability to the Atmel DMA controller available on some AT91 SOCs. This allow peripheral to memory and memory to peripheral transfers with hardware handshaking. Slave structure for controller specific information is passed through channel private data. This at_dma_slave structure is defined in at_hdmac.h header file and relative hardware definition are moved to this file from at_hdmac_regs.h. Doing this we allow the channel configuration from platform definition code. This work is intensively based on dw_dmac and several slave implementations. Signed-off-by: Nicolas Ferre Signed-off-by: Dan Williams --- arch/arm/mach-at91/include/mach/at_hdmac.h | 76 ++++++++ drivers/dma/at_hdmac.c | 208 ++++++++++++++++++++- drivers/dma/at_hdmac_regs.h | 49 +---- 3 files changed, 290 insertions(+), 43 deletions(-) diff --git a/arch/arm/mach-at91/include/mach/at_hdmac.h b/arch/arm/mach-at91/include/mach/at_hdmac.h index 21a5554f9cb..187cb58345c 100644 --- a/arch/arm/mach-at91/include/mach/at_hdmac.h +++ b/arch/arm/mach-at91/include/mach/at_hdmac.h @@ -23,4 +23,80 @@ struct at_dma_platform_data { dma_cap_mask_t cap_mask; }; +/** + * enum at_dma_slave_width - DMA slave register access width. + * @AT_DMA_SLAVE_WIDTH_8BIT: Do 8-bit slave register accesses + * @AT_DMA_SLAVE_WIDTH_16BIT: Do 16-bit slave register accesses + * @AT_DMA_SLAVE_WIDTH_32BIT: Do 32-bit slave register accesses + */ +enum at_dma_slave_width { + AT_DMA_SLAVE_WIDTH_8BIT = 0, + AT_DMA_SLAVE_WIDTH_16BIT, + AT_DMA_SLAVE_WIDTH_32BIT, +}; + +/** + * struct at_dma_slave - Controller-specific information about a slave + * @dma_dev: required DMA master device + * @tx_reg: physical address of data register used for + * memory-to-peripheral transfers + * @rx_reg: physical address of data register used for + * peripheral-to-memory transfers + * @reg_width: peripheral register width + * @cfg: Platform-specific initializer for the CFG register + * @ctrla: Platform-specific initializer for the CTRLA register + */ +struct at_dma_slave { + struct device *dma_dev; + dma_addr_t tx_reg; + dma_addr_t rx_reg; + enum at_dma_slave_width reg_width; + u32 cfg; + u32 ctrla; +}; + + +/* Platform-configurable bits in CFG */ +#define ATC_SRC_PER(h) (0xFU & (h)) /* Channel src rq associated with periph handshaking ifc h */ +#define ATC_DST_PER(h) ((0xFU & (h)) << 4) /* Channel dst rq associated with periph handshaking ifc h */ +#define ATC_SRC_REP (0x1 << 8) /* Source Replay Mod */ +#define ATC_SRC_H2SEL (0x1 << 9) /* Source Handshaking Mod */ +#define ATC_SRC_H2SEL_SW (0x0 << 9) +#define ATC_SRC_H2SEL_HW (0x1 << 9) +#define ATC_DST_REP (0x1 << 12) /* Destination Replay Mod */ +#define ATC_DST_H2SEL (0x1 << 13) /* Destination Handshaking Mod */ +#define ATC_DST_H2SEL_SW (0x0 << 13) +#define ATC_DST_H2SEL_HW (0x1 << 13) +#define ATC_SOD (0x1 << 16) /* Stop On Done */ +#define ATC_LOCK_IF (0x1 << 20) /* Interface Lock */ +#define ATC_LOCK_B (0x1 << 21) /* AHB Bus Lock */ +#define ATC_LOCK_IF_L (0x1 << 22) /* Master Interface Arbiter Lock */ +#define ATC_LOCK_IF_L_CHUNK (0x0 << 22) +#define ATC_LOCK_IF_L_BUFFER (0x1 << 22) +#define ATC_AHB_PROT_MASK (0x7 << 24) /* AHB Protection */ +#define ATC_FIFOCFG_MASK (0x3 << 28) /* FIFO Request Configuration */ +#define ATC_FIFOCFG_LARGESTBURST (0x0 << 28) +#define ATC_FIFOCFG_HALFFIFO (0x1 << 28) +#define ATC_FIFOCFG_ENOUGHSPACE (0x2 << 28) + +/* Platform-configurable bits in CTRLA */ +#define ATC_SCSIZE_MASK (0x7 << 16) /* Source Chunk Transfer Size */ +#define ATC_SCSIZE_1 (0x0 << 16) +#define ATC_SCSIZE_4 (0x1 << 16) +#define ATC_SCSIZE_8 (0x2 << 16) +#define ATC_SCSIZE_16 (0x3 << 16) +#define ATC_SCSIZE_32 (0x4 << 16) +#define ATC_SCSIZE_64 (0x5 << 16) +#define ATC_SCSIZE_128 (0x6 << 16) +#define ATC_SCSIZE_256 (0x7 << 16) +#define ATC_DCSIZE_MASK (0x7 << 20) /* Destination Chunk Transfer Size */ +#define ATC_DCSIZE_1 (0x0 << 20) +#define ATC_DCSIZE_4 (0x1 << 20) +#define ATC_DCSIZE_8 (0x2 << 20) +#define ATC_DCSIZE_16 (0x3 << 20) +#define ATC_DCSIZE_32 (0x4 << 20) +#define ATC_DCSIZE_64 (0x5 << 20) +#define ATC_DCSIZE_128 (0x6 << 20) +#define ATC_DCSIZE_256 (0x7 << 20) + #endif /* AT_HDMAC_H */ diff --git a/drivers/dma/at_hdmac.c b/drivers/dma/at_hdmac.c index 64dbf0ce128..9a1e5fb412e 100644 --- a/drivers/dma/at_hdmac.c +++ b/drivers/dma/at_hdmac.c @@ -608,6 +608,187 @@ err_desc_get: return NULL; } + +/** + * atc_prep_slave_sg - prepare descriptors for a DMA_SLAVE transaction + * @chan: DMA channel + * @sgl: scatterlist to transfer to/from + * @sg_len: number of entries in @scatterlist + * @direction: DMA direction + * @flags: tx descriptor status flags + */ +static struct dma_async_tx_descriptor * +atc_prep_slave_sg(struct dma_chan *chan, struct scatterlist *sgl, + unsigned int sg_len, enum dma_data_direction direction, + unsigned long flags) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + struct at_dma_slave *atslave = chan->private; + struct at_desc *first = NULL; + struct at_desc *prev = NULL; + u32 ctrla; + u32 ctrlb; + dma_addr_t reg; + unsigned int reg_width; + unsigned int mem_width; + unsigned int i; + struct scatterlist *sg; + size_t total_len = 0; + + dev_vdbg(chan2dev(chan), "prep_slave_sg: %s f0x%lx\n", + direction == DMA_TO_DEVICE ? "TO DEVICE" : "FROM DEVICE", + flags); + + if (unlikely(!atslave || !sg_len)) { + dev_dbg(chan2dev(chan), "prep_dma_memcpy: length is zero!\n"); + return NULL; + } + + reg_width = atslave->reg_width; + + sg_len = dma_map_sg(chan2parent(chan), sgl, sg_len, direction); + + ctrla = ATC_DEFAULT_CTRLA | atslave->ctrla; + ctrlb = ATC_DEFAULT_CTRLB | ATC_IEN; + + switch (direction) { + case DMA_TO_DEVICE: + ctrla |= ATC_DST_WIDTH(reg_width); + ctrlb |= ATC_DST_ADDR_MODE_FIXED + | ATC_SRC_ADDR_MODE_INCR + | ATC_FC_MEM2PER; + reg = atslave->tx_reg; + for_each_sg(sgl, sg, sg_len, i) { + struct at_desc *desc; + u32 len; + u32 mem; + + desc = atc_desc_get(atchan); + if (!desc) + goto err_desc_get; + + mem = sg_phys(sg); + len = sg_dma_len(sg); + mem_width = 2; + if (unlikely(mem & 3 || len & 3)) + mem_width = 0; + + desc->lli.saddr = mem; + desc->lli.daddr = reg; + desc->lli.ctrla = ctrla + | ATC_SRC_WIDTH(mem_width) + | len >> mem_width; + desc->lli.ctrlb = ctrlb; + + if (!first) { + first = desc; + } else { + /* inform the HW lli about chaining */ + prev->lli.dscr = desc->txd.phys; + /* insert the link descriptor to the LD ring */ + list_add_tail(&desc->desc_node, + &first->txd.tx_list); + } + prev = desc; + total_len += len; + } + break; + case DMA_FROM_DEVICE: + ctrla |= ATC_SRC_WIDTH(reg_width); + ctrlb |= ATC_DST_ADDR_MODE_INCR + | ATC_SRC_ADDR_MODE_FIXED + | ATC_FC_PER2MEM; + + reg = atslave->rx_reg; + for_each_sg(sgl, sg, sg_len, i) { + struct at_desc *desc; + u32 len; + u32 mem; + + desc = atc_desc_get(atchan); + if (!desc) + goto err_desc_get; + + mem = sg_phys(sg); + len = sg_dma_len(sg); + mem_width = 2; + if (unlikely(mem & 3 || len & 3)) + mem_width = 0; + + desc->lli.saddr = reg; + desc->lli.daddr = mem; + desc->lli.ctrla = ctrla + | ATC_DST_WIDTH(mem_width) + | len >> mem_width; + desc->lli.ctrlb = ctrlb; + + if (!first) { + first = desc; + } else { + /* inform the HW lli about chaining */ + prev->lli.dscr = desc->txd.phys; + /* insert the link descriptor to the LD ring */ + list_add_tail(&desc->desc_node, + &first->txd.tx_list); + } + prev = desc; + total_len += len; + } + break; + default: + return NULL; + } + + /* set end-of-link to the last link descriptor of list*/ + set_desc_eol(prev); + + /* First descriptor of the chain embedds additional information */ + first->txd.cookie = -EBUSY; + first->len = total_len; + + /* last link descriptor of list is responsible of flags */ + prev->txd.flags = flags; /* client is in control of this ack */ + + return &first->txd; + +err_desc_get: + dev_err(chan2dev(chan), "not enough descriptors available\n"); + atc_desc_put(atchan, first); + return NULL; +} + +static void atc_terminate_all(struct dma_chan *chan) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + struct at_dma *atdma = to_at_dma(chan->device); + struct at_desc *desc, *_desc; + LIST_HEAD(list); + + /* + * This is only called when something went wrong elsewhere, so + * we don't really care about the data. Just disable the + * channel. We still have to poll the channel enable bit due + * to AHB/HSB limitations. + */ + spin_lock_bh(&atchan->lock); + + dma_writel(atdma, CHDR, atchan->mask); + + /* confirm that this channel is disabled */ + while (dma_readl(atdma, CHSR) & atchan->mask) + cpu_relax(); + + /* active_list entries will end up before queued entries */ + list_splice_init(&atchan->queue, &list); + list_splice_init(&atchan->active_list, &list); + + spin_unlock_bh(&atchan->lock); + + /* Flush all pending and queued descriptors */ + list_for_each_entry_safe(desc, _desc, &list, desc_node) + atc_chain_complete(atchan, desc); +} + /** * atc_is_tx_complete - poll for transaction completion * @chan: DMA channel @@ -686,7 +867,9 @@ static int atc_alloc_chan_resources(struct dma_chan *chan) struct at_dma_chan *atchan = to_at_dma_chan(chan); struct at_dma *atdma = to_at_dma(chan->device); struct at_desc *desc; + struct at_dma_slave *atslave; int i; + u32 cfg; LIST_HEAD(tmp_list); dev_vdbg(chan2dev(chan), "alloc_chan_resources\n"); @@ -697,7 +880,23 @@ static int atc_alloc_chan_resources(struct dma_chan *chan) return -EIO; } - /* have we already been set up? */ + cfg = ATC_DEFAULT_CFG; + + atslave = chan->private; + if (atslave) { + /* + * We need controller-specific data to set up slave + * transfers. + */ + BUG_ON(!atslave->dma_dev || atslave->dma_dev != atdma->dma_common.dev); + + /* if cfg configuration specified take it instad of default */ + if (atslave->cfg) + cfg = atslave->cfg; + } + + /* have we already been set up? + * reconfigure channel but no need to reallocate descriptors */ if (!list_empty(&atchan->free_list)) return atchan->descs_allocated; @@ -719,7 +918,7 @@ static int atc_alloc_chan_resources(struct dma_chan *chan) spin_unlock_bh(&atchan->lock); /* channel parameters */ - channel_writel(atchan, CFG, ATC_DEFAULT_CFG); + channel_writel(atchan, CFG, cfg); dev_dbg(chan2dev(chan), "alloc_chan_resources: allocated %d descriptors\n", @@ -888,6 +1087,11 @@ static int __init at_dma_probe(struct platform_device *pdev) if (dma_has_cap(DMA_MEMCPY, atdma->dma_common.cap_mask)) atdma->dma_common.device_prep_dma_memcpy = atc_prep_dma_memcpy; + if (dma_has_cap(DMA_SLAVE, atdma->dma_common.cap_mask)) { + atdma->dma_common.device_prep_slave_sg = atc_prep_slave_sg; + atdma->dma_common.device_terminate_all = atc_terminate_all; + } + dma_writel(atdma, EN, AT_DMA_ENABLE); dev_info(&pdev->dev, "Atmel AHB DMA Controller ( %s%s), %d channels\n", diff --git a/drivers/dma/at_hdmac_regs.h b/drivers/dma/at_hdmac_regs.h index ad2d4f402bf..4c972afc49e 100644 --- a/drivers/dma/at_hdmac_regs.h +++ b/drivers/dma/at_hdmac_regs.h @@ -87,29 +87,14 @@ /* Bitfields in CTRLA */ #define ATC_BTSIZE_MAX 0xFFFFUL /* Maximum Buffer Transfer Size */ #define ATC_BTSIZE(x) (ATC_BTSIZE_MAX & (x)) /* Buffer Transfer Size */ -#define ATC_SCSIZE_MASK (0x7 << 16) /* Source Chunk Transfer Size */ -#define ATC_SCSIZE_1 (0x0 << 16) -#define ATC_SCSIZE_4 (0x1 << 16) -#define ATC_SCSIZE_8 (0x2 << 16) -#define ATC_SCSIZE_16 (0x3 << 16) -#define ATC_SCSIZE_32 (0x4 << 16) -#define ATC_SCSIZE_64 (0x5 << 16) -#define ATC_SCSIZE_128 (0x6 << 16) -#define ATC_SCSIZE_256 (0x7 << 16) -#define ATC_DCSIZE_MASK (0x7 << 20) /* Destination Chunk Transfer Size */ -#define ATC_DCSIZE_1 (0x0 << 20) -#define ATC_DCSIZE_4 (0x1 << 20) -#define ATC_DCSIZE_8 (0x2 << 20) -#define ATC_DCSIZE_16 (0x3 << 20) -#define ATC_DCSIZE_32 (0x4 << 20) -#define ATC_DCSIZE_64 (0x5 << 20) -#define ATC_DCSIZE_128 (0x6 << 20) -#define ATC_DCSIZE_256 (0x7 << 20) +/* Chunck Tranfer size definitions are in at_hdmac.h */ #define ATC_SRC_WIDTH_MASK (0x3 << 24) /* Source Single Transfer Size */ +#define ATC_SRC_WIDTH(x) ((x) << 24) #define ATC_SRC_WIDTH_BYTE (0x0 << 24) #define ATC_SRC_WIDTH_HALFWORD (0x1 << 24) #define ATC_SRC_WIDTH_WORD (0x2 << 24) #define ATC_DST_WIDTH_MASK (0x3 << 28) /* Destination Single Transfer Size */ +#define ATC_DST_WIDTH(x) ((x) << 28) #define ATC_DST_WIDTH_BYTE (0x0 << 28) #define ATC_DST_WIDTH_HALFWORD (0x1 << 28) #define ATC_DST_WIDTH_WORD (0x2 << 28) @@ -129,7 +114,8 @@ #define ATC_FC_PER2PER (0x3 << 21) /* Periph-to-Periph (DMA) */ #define ATC_FC_PER2MEM_PER (0x4 << 21) /* Periph-to-Mem (Peripheral) */ #define ATC_FC_MEM2PER_PER (0x5 << 21) /* Mem-to-Periph (Peripheral) */ -#define ATC_FC_PER2PER_PER (0x6 << 21) /* Periph-to-Periph (Src Peripheral) */ +#define ATC_FC_PER2PER_SRCPER (0x6 << 21) /* Periph-to-Periph (Src Peripheral) */ +#define ATC_FC_PER2PER_DSTPER (0x7 << 21) /* Periph-to-Periph (Dst Peripheral) */ #define ATC_SRC_ADDR_MODE_MASK (0x3 << 24) #define ATC_SRC_ADDR_MODE_INCR (0x0 << 24) /* Incrementing Mode */ #define ATC_SRC_ADDR_MODE_DECR (0x1 << 24) /* Decrementing Mode */ @@ -142,27 +128,7 @@ #define ATC_AUTO (0x1 << 31) /* Auto multiple buffer tx enable */ /* Bitfields in CFG */ -#define ATC_SRC_PER(h) (0xFU & (h)) /* Channel src rq associated with periph handshaking ifc h */ -#define ATC_DST_PER(h) ((0xFU & (h)) << 4) /* Channel dst rq associated with periph handshaking ifc h */ -#define ATC_SRC_REP (0x1 << 8) /* Source Replay Mod */ -#define ATC_SRC_H2SEL (0x1 << 9) /* Source Handshaking Mod */ -#define ATC_SRC_H2SEL_SW (0x0 << 9) -#define ATC_SRC_H2SEL_HW (0x1 << 9) -#define ATC_DST_REP (0x1 << 12) /* Destination Replay Mod */ -#define ATC_DST_H2SEL (0x1 << 13) /* Destination Handshaking Mod */ -#define ATC_DST_H2SEL_SW (0x0 << 13) -#define ATC_DST_H2SEL_HW (0x1 << 13) -#define ATC_SOD (0x1 << 16) /* Stop On Done */ -#define ATC_LOCK_IF (0x1 << 20) /* Interface Lock */ -#define ATC_LOCK_B (0x1 << 21) /* AHB Bus Lock */ -#define ATC_LOCK_IF_L (0x1 << 22) /* Master Interface Arbiter Lock */ -#define ATC_LOCK_IF_L_CHUNK (0x0 << 22) -#define ATC_LOCK_IF_L_BUFFER (0x1 << 22) -#define ATC_AHB_PROT_MASK (0x7 << 24) /* AHB Protection */ -#define ATC_FIFOCFG_MASK (0x3 << 28) /* FIFO Request Configuration */ -#define ATC_FIFOCFG_LARGESTBURST (0x0 << 28) -#define ATC_FIFOCFG_HALFFIFO (0x1 << 28) -#define ATC_FIFOCFG_ENOUGHSPACE (0x2 << 28) +/* are in at_hdmac.h */ /* Bitfields in SPIP */ #define ATC_SPIP_HOLE(x) (0xFFFFU & (x)) @@ -316,11 +282,12 @@ static void vdbg_dump_regs(struct at_dma_chan *atchan) dma_readl(atdma, CHSR)); dev_err(chan2dev(&atchan->chan_common), - " channel: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n", + " channel: s0x%x d0x%x ctrl0x%x:0x%x cfg0x%x l0x%x\n", channel_readl(atchan, SADDR), channel_readl(atchan, DADDR), channel_readl(atchan, CTRLA), channel_readl(atchan, CTRLB), + channel_readl(atchan, CFG), channel_readl(atchan, DSCR)); } #else -- GitLab From 06c71282a90470184a78f7f0ab0f7ce0fc1f69c8 Mon Sep 17 00:00:00 2001 From: Chaithrika U S Date: Wed, 22 Jul 2009 07:45:04 -0400 Subject: [PATCH 0233/1342] ASoC: tlv320aic3x: Enable PLL when not bypassed PLL was not being enabled when it was not bypassed. This patch enables the PLL when it is used. Additionally, it disables the PLL when it is bypassed. Without this patch, the audio on TI DM646x EVM and DM355 EVM does not work properly. The bit clocks and the frame sync signals from the codec are not correct and hence the playback/record are faster than usual for most sample rates. The reason for this was that the PLL was not enabled when it was not bypassed. Tested on DM6467 EVM, playback tested on DM355 EVM. Signed-off-by: Chaithrika U S Signed-off-by: Mark Brown --- sound/soc/codecs/tlv320aic3x.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-) diff --git a/sound/soc/codecs/tlv320aic3x.c b/sound/soc/codecs/tlv320aic3x.c index ab099f48248..cb0d1bf34b5 100644 --- a/sound/soc/codecs/tlv320aic3x.c +++ b/sound/soc/codecs/tlv320aic3x.c @@ -767,6 +767,7 @@ static int aic3x_hw_params(struct snd_pcm_substream *substream, int codec_clk = 0, bypass_pll = 0, fsref, last_clk = 0; u8 data, r, p, pll_q, pll_p = 1, pll_r = 1, pll_j = 1; u16 pll_d = 1; + u8 reg; /* select data word length */ data = @@ -801,8 +802,16 @@ static int aic3x_hw_params(struct snd_pcm_substream *substream, pll_q &= 0xf; aic3x_write(codec, AIC3X_PLL_PROGA_REG, pll_q << PLLQ_SHIFT); aic3x_write(codec, AIC3X_GPIOB_REG, CODEC_CLKIN_CLKDIV); - } else + /* disable PLL if it is bypassed */ + reg = aic3x_read_reg_cache(codec, AIC3X_PLL_PROGA_REG); + aic3x_write(codec, AIC3X_PLL_PROGA_REG, reg & ~PLL_ENABLE); + + } else { aic3x_write(codec, AIC3X_GPIOB_REG, CODEC_CLKIN_PLLDIV); + /* enable PLL when it is used */ + reg = aic3x_read_reg_cache(codec, AIC3X_PLL_PROGA_REG); + aic3x_write(codec, AIC3X_PLL_PROGA_REG, reg | PLL_ENABLE); + } /* Route Left DAC to left channel input and * right DAC to right channel input */ -- GitLab From cedb8118e8cef21a2b73fd9cb70660ac19124c16 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Thu, 23 Jul 2009 11:04:13 +0200 Subject: [PATCH 0234/1342] ALSA: pcm - Add logging of hwptr updates and interrupt updates Added the logging functionality to xrun_debug to record the hwptr updates via snd_pcm_update_hw_ptr() and snd_pcm_update_hwptr_interrupt(), corresponding to 16 and 8, respectively. For example, # echo 9 > /proc/asound/card0/pcm0p/xrun_debug will record the position and other parameters at each period interrupt together with the normal XRUN debugging. Signed-off-by: Takashi Iwai --- Documentation/sound/alsa/Procfile.txt | 5 +++++ sound/core/pcm_lib.c | 25 +++++++++++++++++++++++++ 2 files changed, 30 insertions(+) diff --git a/Documentation/sound/alsa/Procfile.txt b/Documentation/sound/alsa/Procfile.txt index 381908d8ca4..719a819f8cc 100644 --- a/Documentation/sound/alsa/Procfile.txt +++ b/Documentation/sound/alsa/Procfile.txt @@ -101,6 +101,8 @@ card*/pcm*/xrun_debug bit 0 = Enable XRUN/jiffies debug messages bit 1 = Show stack trace at XRUN / jiffies check bit 2 = Enable additional jiffies check + bit 3 = Log hwptr update at each period interrupt + bit 4 = Log hwptr update at each snd_pcm_update_hw_ptr() When the bit 0 is set, the driver will show the messages to kernel log when an xrun is detected. The debug message is @@ -117,6 +119,9 @@ card*/pcm*/xrun_debug buggy) hardware that doesn't give smooth pointer updates. This feature is enabled via the bit 2. + Bits 3 and 4 are for logging the hwptr records. Note that + these will give flood of kernel messages. + card*/pcm*/sub*/info The general information of this PCM sub-stream. diff --git a/sound/core/pcm_lib.c b/sound/core/pcm_lib.c index 3b673e2f991..065eaf0a386 100644 --- a/sound/core/pcm_lib.c +++ b/sound/core/pcm_lib.c @@ -233,6 +233,18 @@ static int snd_pcm_update_hw_ptr_interrupt(struct snd_pcm_substream *substream) xrun(substream); return -EPIPE; } + if (xrun_debug(substream, 8)) { + char name[16]; + pcm_debug_name(substream, name, sizeof(name)); + snd_printd("period_update: %s: pos=0x%x/0x%x/0x%x, " + "hwptr=0x%lx, hw_base=0x%lx, hw_intr=0x%lx\n", + name, pos, + (int)runtime->period_size, + (int)runtime->buffer_size, + (long)old_hw_ptr, + (long)runtime->hw_ptr_base, + (long)runtime->hw_ptr_interrupt); + } hw_base = runtime->hw_ptr_base; new_hw_ptr = hw_base + pos; hw_ptr_interrupt = runtime->hw_ptr_interrupt + runtime->period_size; @@ -353,6 +365,19 @@ int snd_pcm_update_hw_ptr(struct snd_pcm_substream *substream) xrun(substream); return -EPIPE; } + if (xrun_debug(substream, 16)) { + char name[16]; + pcm_debug_name(substream, name, sizeof(name)); + snd_printd("hw_update: %s: pos=0x%x/0x%x/0x%x, " + "hwptr=0x%lx, hw_base=0x%lx, hw_intr=0x%lx\n", + name, pos, + (int)runtime->period_size, + (int)runtime->buffer_size, + (long)old_hw_ptr, + (long)runtime->hw_ptr_base, + (long)runtime->hw_ptr_interrupt); + } + hw_base = runtime->hw_ptr_base; new_hw_ptr = hw_base + pos; -- GitLab From 3174c88af4b6b2e81cacfaa2bb90cc7abe36f1cc Mon Sep 17 00:00:00 2001 From: Hartley Sweeten Date: Mon, 20 Jul 2009 18:12:23 +0100 Subject: [PATCH 0235/1342] [ARM] 5611/1: ep93xx: update ts72xx nor flash support Update the NOR flash support for TS-7200. The TS-7200 models all have 16-bit NOR flash. Update the platform init to support this. Remove the private TS72XX_NOR_* defines and use the common ep93xx defines for the external chip select physical base address instead. Move the NOR flash registration into a static __init function. When the NAND flash support is updated this function will also be used to register the NAND flash for the TS-7250 and TS-7260. Tested-by: Matthieu Crapet Signed-off-by: H Hartley Sweeten Signed-off-by: Russell King --- arch/arm/mach-ep93xx/include/mach/ts72xx.h | 3 --- arch/arm/mach-ep93xx/ts72xx.c | 18 +++++++++++++----- 2 files changed, 13 insertions(+), 8 deletions(-) diff --git a/arch/arm/mach-ep93xx/include/mach/ts72xx.h b/arch/arm/mach-ep93xx/include/mach/ts72xx.h index 34ddec081c4..411734422c1 100644 --- a/arch/arm/mach-ep93xx/include/mach/ts72xx.h +++ b/arch/arm/mach-ep93xx/include/mach/ts72xx.h @@ -41,9 +41,6 @@ #define TS72XX_OPTIONS2_TS9420_BOOT 0x02 -#define TS72XX_NOR_PHYS_BASE 0x60000000 -#define TS72XX_NOR2_PHYS_BASE 0x62000000 - #define TS72XX_NAND1_DATA_PHYS_BASE 0x60000000 #define TS72XX_NAND2_DATA_PHYS_BASE 0x70000000 #define TS72XX_NAND_DATA_VIRT_BASE 0xfebfc000 diff --git a/arch/arm/mach-ep93xx/ts72xx.c b/arch/arm/mach-ep93xx/ts72xx.c index 7ee024d3482..aaf1371412a 100644 --- a/arch/arm/mach-ep93xx/ts72xx.c +++ b/arch/arm/mach-ep93xx/ts72xx.c @@ -112,13 +112,16 @@ static void __init ts72xx_map_io(void) } } +/************************************************************************* + * NOR flash (TS-7200 only) + *************************************************************************/ static struct physmap_flash_data ts72xx_flash_data = { - .width = 1, + .width = 2, }; static struct resource ts72xx_flash_resource = { - .start = TS72XX_NOR_PHYS_BASE, - .end = TS72XX_NOR_PHYS_BASE + SZ_16M - 1, + .start = EP93XX_CS6_PHYS_BASE, + .end = EP93XX_CS6_PHYS_BASE + SZ_16M - 1, .flags = IORESOURCE_MEM, }; @@ -132,6 +135,12 @@ static struct platform_device ts72xx_flash = { .resource = &ts72xx_flash_resource, }; +static void __init ts72xx_register_flash(void) +{ + if (board_is_ts7200()) + platform_device_register(&ts72xx_flash); +} + static unsigned char ts72xx_rtc_readbyte(unsigned long addr) { __raw_writeb(addr, TS72XX_RTC_INDEX_VIRT_BASE); @@ -165,8 +174,7 @@ static struct ep93xx_eth_data ts72xx_eth_data = { static void __init ts72xx_init_machine(void) { ep93xx_init_devices(); - if (board_is_ts7200()) - platform_device_register(&ts72xx_flash); + ts72xx_register_flash(); platform_device_register(&ts72xx_rtc_device); ep93xx_register_eth(&ts72xx_eth_data, 1); -- GitLab From 89350640439e0160056de26995d52deb18202b3e Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Thu, 23 Jul 2009 14:28:37 +0200 Subject: [PATCH 0236/1342] ALSA: pcm - Fix warnings in debug loggings Add proper cast. Signed-off-by: Takashi Iwai --- sound/core/pcm_lib.c | 24 ++++++++++++------------ 1 file changed, 12 insertions(+), 12 deletions(-) diff --git a/sound/core/pcm_lib.c b/sound/core/pcm_lib.c index 065eaf0a386..d315f72949f 100644 --- a/sound/core/pcm_lib.c +++ b/sound/core/pcm_lib.c @@ -238,12 +238,12 @@ static int snd_pcm_update_hw_ptr_interrupt(struct snd_pcm_substream *substream) pcm_debug_name(substream, name, sizeof(name)); snd_printd("period_update: %s: pos=0x%x/0x%x/0x%x, " "hwptr=0x%lx, hw_base=0x%lx, hw_intr=0x%lx\n", - name, pos, - (int)runtime->period_size, - (int)runtime->buffer_size, - (long)old_hw_ptr, - (long)runtime->hw_ptr_base, - (long)runtime->hw_ptr_interrupt); + name, (unsigned int)pos, + (unsigned int)runtime->period_size, + (unsigned int)runtime->buffer_size, + (unsigned long)old_hw_ptr, + (unsigned long)runtime->hw_ptr_base, + (unsigned long)runtime->hw_ptr_interrupt); } hw_base = runtime->hw_ptr_base; new_hw_ptr = hw_base + pos; @@ -370,12 +370,12 @@ int snd_pcm_update_hw_ptr(struct snd_pcm_substream *substream) pcm_debug_name(substream, name, sizeof(name)); snd_printd("hw_update: %s: pos=0x%x/0x%x/0x%x, " "hwptr=0x%lx, hw_base=0x%lx, hw_intr=0x%lx\n", - name, pos, - (int)runtime->period_size, - (int)runtime->buffer_size, - (long)old_hw_ptr, - (long)runtime->hw_ptr_base, - (long)runtime->hw_ptr_interrupt); + name, (unsigned int)pos, + (unsigned int)runtime->period_size, + (unsigned int)runtime->buffer_size, + (unsigned long)old_hw_ptr, + (unsigned long)runtime->hw_ptr_base, + (unsigned long)runtime->hw_ptr_interrupt); } hw_base = runtime->hw_ptr_base; -- GitLab From d8cc1ab793993c886c62abf77c93287df33ffd8b Mon Sep 17 00:00:00 2001 From: Li Zefan Date: Thu, 23 Jul 2009 11:28:40 +0800 Subject: [PATCH 0237/1342] trace_stack: Fix seqfile memory leak Every time we cat stack_trace, we leak memory allocated by seq_open(). Signed-off-by: Li Zefan LKML-Reference: <4A67D8E8.3020500@cn.fujitsu.com> Signed-off-by: Steven Rostedt --- kernel/trace/trace_stack.c | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-) diff --git a/kernel/trace/trace_stack.c b/kernel/trace/trace_stack.c index e644af91012..6a2a9d484cd 100644 --- a/kernel/trace/trace_stack.c +++ b/kernel/trace/trace_stack.c @@ -301,17 +301,14 @@ static const struct seq_operations stack_trace_seq_ops = { static int stack_trace_open(struct inode *inode, struct file *file) { - int ret; - - ret = seq_open(file, &stack_trace_seq_ops); - - return ret; + return seq_open(file, &stack_trace_seq_ops); } static const struct file_operations stack_trace_fops = { .open = stack_trace_open, .read = seq_read, .llseek = seq_lseek, + .release = seq_release, }; int -- GitLab From 87827111a5538633b18e5c641ced673c4c2bb6ce Mon Sep 17 00:00:00 2001 From: Li Zefan Date: Thu, 23 Jul 2009 11:29:11 +0800 Subject: [PATCH 0238/1342] function-graph: Fix seqfile memory leak Every time we cat set_graph_function, we leak memory allocated by seq_open(). Signed-off-by: Li Zefan LKML-Reference: <4A67D907.2010500@cn.fujitsu.com> Signed-off-by: Steven Rostedt --- kernel/trace/ftrace.c | 15 ++++++++++++--- 1 file changed, 12 insertions(+), 3 deletions(-) diff --git a/kernel/trace/ftrace.c b/kernel/trace/ftrace.c index 4521c77d1a1..1f3ec2afa51 100644 --- a/kernel/trace/ftrace.c +++ b/kernel/trace/ftrace.c @@ -2595,6 +2595,14 @@ ftrace_graph_open(struct inode *inode, struct file *file) return ret; } +static int +ftrace_graph_release(struct inode *inode, struct file *file) +{ + if (file->f_mode & FMODE_READ) + seq_release(inode, file); + return 0; +} + static int ftrace_set_func(unsigned long *array, int *idx, char *buffer) { @@ -2724,9 +2732,10 @@ ftrace_graph_write(struct file *file, const char __user *ubuf, } static const struct file_operations ftrace_graph_fops = { - .open = ftrace_graph_open, - .read = seq_read, - .write = ftrace_graph_write, + .open = ftrace_graph_open, + .read = seq_read, + .write = ftrace_graph_write, + .release = ftrace_graph_release, }; #endif /* CONFIG_FUNCTION_GRAPH_TRACER */ -- GitLab From 636eacee3b0c76915151db37203cc624becb6d7b Mon Sep 17 00:00:00 2001 From: Li Zefan Date: Thu, 23 Jul 2009 11:29:47 +0800 Subject: [PATCH 0239/1342] tracing/stat: Fix seqfile memory leak Every time we cat a trace_stat file, we leak memory allocated by seq_open(). Also fix memory leak in a failure path in tracing_stat_open(). Signed-off-by: Li Zefan LKML-Reference: <4A67D92B.4060704@cn.fujitsu.com> Signed-off-by: Steven Rostedt --- kernel/trace/trace_stat.c | 34 ++++++++++++++++++++++------------ 1 file changed, 22 insertions(+), 12 deletions(-) diff --git a/kernel/trace/trace_stat.c b/kernel/trace/trace_stat.c index e66f5e49334..aea321c82fa 100644 --- a/kernel/trace/trace_stat.c +++ b/kernel/trace/trace_stat.c @@ -73,7 +73,7 @@ static struct rb_node *release_next(struct rb_node *node) } } -static void reset_stat_session(struct stat_session *session) +static void __reset_stat_session(struct stat_session *session) { struct rb_node *node = session->stat_root.rb_node; @@ -83,10 +83,17 @@ static void reset_stat_session(struct stat_session *session) session->stat_root = RB_ROOT; } +static void reset_stat_session(struct stat_session *session) +{ + mutex_lock(&session->stat_mutex); + __reset_stat_session(session); + mutex_unlock(&session->stat_mutex); +} + static void destroy_session(struct stat_session *session) { debugfs_remove(session->file); - reset_stat_session(session); + __reset_stat_session(session); mutex_destroy(&session->stat_mutex); kfree(session); } @@ -150,7 +157,7 @@ static int stat_seq_init(struct stat_session *session) int i; mutex_lock(&session->stat_mutex); - reset_stat_session(session); + __reset_stat_session(session); if (!ts->stat_cmp) ts->stat_cmp = dummy_cmp; @@ -183,7 +190,7 @@ exit: return ret; exit_free_rbtree: - reset_stat_session(session); + __reset_stat_session(session); mutex_unlock(&session->stat_mutex); return ret; } @@ -250,16 +257,21 @@ static const struct seq_operations trace_stat_seq_ops = { static int tracing_stat_open(struct inode *inode, struct file *file) { int ret; - + struct seq_file *m; struct stat_session *session = inode->i_private; + ret = stat_seq_init(session); + if (ret) + return ret; + ret = seq_open(file, &trace_stat_seq_ops); - if (!ret) { - struct seq_file *m = file->private_data; - m->private = session; - ret = stat_seq_init(session); + if (ret) { + reset_stat_session(session); + return ret; } + m = file->private_data; + m->private = session; return ret; } @@ -270,11 +282,9 @@ static int tracing_stat_release(struct inode *i, struct file *f) { struct stat_session *session = i->i_private; - mutex_lock(&session->stat_mutex); reset_stat_session(session); - mutex_unlock(&session->stat_mutex); - return 0; + return seq_release(i, f); } static const struct file_operations tracing_stat_fops = { -- GitLab From 4c739ff043e5787d97c9691d62cabf7a29e75a9d Mon Sep 17 00:00:00 2001 From: Steven Rostedt Date: Wed, 22 Jul 2009 23:11:03 -0400 Subject: [PATCH 0240/1342] tracing: show proper address for trace-printk format Since the trace_printk may use pointers to the format fields in the buffer, they are exported via debugfs/tracing/printk_formats. This is used by utilities that read the ring buffer in binary format. It helps the utilities map the address of the format in the binary buffer to what the printf format looks like. Unfortunately, the way the output code works, it exports the address of the pointer to the format address, and not the format address itself. This makes the file totally useless in trying to figure out what format string a binary address belongs to. Signed-off-by: Steven Rostedt --- kernel/trace/trace_printk.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/trace/trace_printk.c b/kernel/trace/trace_printk.c index 7b627811082..687699d365a 100644 --- a/kernel/trace/trace_printk.c +++ b/kernel/trace/trace_printk.c @@ -176,7 +176,7 @@ static int t_show(struct seq_file *m, void *v) const char *str = *fmt; int i; - seq_printf(m, "0x%lx : \"", (unsigned long)fmt); + seq_printf(m, "0x%lx : \"", *(unsigned long *)fmt); /* * Tabs and new lines need to be converted. -- GitLab From 8650ae32ef7045e763825dee6256dde7f331bb85 Mon Sep 17 00:00:00 2001 From: Steven Rostedt Date: Wed, 22 Jul 2009 23:29:30 -0400 Subject: [PATCH 0241/1342] tracing: only truncate ftrace files when O_TRUNC is set The current code will truncate the ftrace files contents if O_APPEND is not set and the file is opened in write mode. This is incorrect. It should only truncate the file if O_TRUNC is set. Otherwise if one of these files is opened by a C program with fopen "r+", it will incorrectly truncate the file. Reported-by: Jiri Olsa Signed-off-by: Steven Rostedt --- kernel/trace/ftrace.c | 4 ++-- kernel/trace/trace.c | 2 +- kernel/trace/trace_events.c | 2 +- 3 files changed, 4 insertions(+), 4 deletions(-) diff --git a/kernel/trace/ftrace.c b/kernel/trace/ftrace.c index 1f3ec2afa51..1e1d23c2630 100644 --- a/kernel/trace/ftrace.c +++ b/kernel/trace/ftrace.c @@ -1662,7 +1662,7 @@ ftrace_regex_open(struct inode *inode, struct file *file, int enable) mutex_lock(&ftrace_regex_lock); if ((file->f_mode & FMODE_WRITE) && - !(file->f_flags & O_APPEND)) + (file->f_flags & O_TRUNC)) ftrace_filter_reset(enable); if (file->f_mode & FMODE_READ) { @@ -2577,7 +2577,7 @@ ftrace_graph_open(struct inode *inode, struct file *file) mutex_lock(&graph_lock); if ((file->f_mode & FMODE_WRITE) && - !(file->f_flags & O_APPEND)) { + (file->f_flags & O_TRUNC)) { ftrace_graph_count = 0; memset(ftrace_graph_funcs, 0, sizeof(ftrace_graph_funcs)); } diff --git a/kernel/trace/trace.c b/kernel/trace/trace.c index 8bc8d8afea6..d8ef28574aa 100644 --- a/kernel/trace/trace.c +++ b/kernel/trace/trace.c @@ -2031,7 +2031,7 @@ static int tracing_open(struct inode *inode, struct file *file) /* If this file was open for write, then erase contents */ if ((file->f_mode & FMODE_WRITE) && - !(file->f_flags & O_APPEND)) { + (file->f_flags & O_TRUNC)) { long cpu = (long) inode->i_private; if (cpu == TRACE_PIPE_ALL_CPU) diff --git a/kernel/trace/trace_events.c b/kernel/trace/trace_events.c index 53c8fd376a8..23d2972b22d 100644 --- a/kernel/trace/trace_events.c +++ b/kernel/trace/trace_events.c @@ -376,7 +376,7 @@ ftrace_event_seq_open(struct inode *inode, struct file *file) const struct seq_operations *seq_ops; if ((file->f_mode & FMODE_WRITE) && - !(file->f_flags & O_APPEND)) + (file->f_flags & O_TRUNC)) ftrace_clear_events(); seq_ops = inode->i_private; -- GitLab From 947ca210f1df7656e19890832cb71fc3bdd88707 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Thu, 23 Jul 2009 16:21:08 +0200 Subject: [PATCH 0242/1342] ALSA: pcm - Fix hwptr buffer-size overlap bug The fix 79452f0a28aa5a40522c487b42a5fc423647ad98 introduced another bug due to the missing offset for the overlapped hwptr. When the hwptr goes back to zero, the delta value has to be corrected with the buffer size. Otherwise this causes looping sounds. Signed-off-by: Takashi Iwai --- sound/core/pcm_lib.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/core/pcm_lib.c b/sound/core/pcm_lib.c index d315f72949f..72cfd47af6b 100644 --- a/sound/core/pcm_lib.c +++ b/sound/core/pcm_lib.c @@ -256,7 +256,7 @@ static int snd_pcm_update_hw_ptr_interrupt(struct snd_pcm_substream *substream) delta = new_hw_ptr - hw_ptr_interrupt; } if (delta < 0) { - if (runtime->periods == 1) + if (runtime->periods == 1 || new_hw_ptr < old_hw_ptr) delta += runtime->buffer_size; if (delta < 0) { hw_ptr_error(substream, -- GitLab From b30c4947735f9d76da3d194923efd38ed18ad651 Mon Sep 17 00:00:00 2001 From: Daniel Mack Date: Wed, 22 Jul 2009 14:13:35 +0200 Subject: [PATCH 0243/1342] ALSA: snd_usb_caiaq: add support for Audio2DJ This adds support for Native Instrument's freshly announced Audio2DJ sound device hardware. Version number bumped to 1.3.19. Signed-off-by: Daniel Mack Signed-off-by: Takashi Iwai --- sound/usb/Kconfig | 1 + sound/usb/caiaq/audio.c | 1 + sound/usb/caiaq/device.c | 8 +++++++- sound/usb/caiaq/device.h | 1 + 4 files changed, 10 insertions(+), 1 deletion(-) diff --git a/sound/usb/Kconfig b/sound/usb/Kconfig index 523aec188cc..73525c048e7 100644 --- a/sound/usb/Kconfig +++ b/sound/usb/Kconfig @@ -48,6 +48,7 @@ config SND_USB_CAIAQ * Native Instruments Kore Controller * Native Instruments Kore Controller 2 * Native Instruments Audio Kontrol 1 + * Native Instruments Audio 2 DJ * Native Instruments Audio 4 DJ * Native Instruments Audio 8 DJ * Native Instruments Guitar Rig Session I/O diff --git a/sound/usb/caiaq/audio.c b/sound/usb/caiaq/audio.c index 8f9b60c5d74..121af0644fd 100644 --- a/sound/usb/caiaq/audio.c +++ b/sound/usb/caiaq/audio.c @@ -646,6 +646,7 @@ int snd_usb_caiaq_audio_init(struct snd_usb_caiaqdev *dev) case USB_ID(USB_VID_NATIVEINSTRUMENTS, USB_PID_GUITARRIGMOBILE): dev->samplerates |= SNDRV_PCM_RATE_192000; /* fall thru */ + case USB_ID(USB_VID_NATIVEINSTRUMENTS, USB_PID_AUDIO2DJ): case USB_ID(USB_VID_NATIVEINSTRUMENTS, USB_PID_AUDIO4DJ): case USB_ID(USB_VID_NATIVEINSTRUMENTS, USB_PID_AUDIO8DJ): dev->samplerates |= SNDRV_PCM_RATE_88200; diff --git a/sound/usb/caiaq/device.c b/sound/usb/caiaq/device.c index de38108f0b2..83e6c1312d4 100644 --- a/sound/usb/caiaq/device.c +++ b/sound/usb/caiaq/device.c @@ -35,13 +35,14 @@ #include "input.h" MODULE_AUTHOR("Daniel Mack "); -MODULE_DESCRIPTION("caiaq USB audio, version 1.3.18"); +MODULE_DESCRIPTION("caiaq USB audio, version 1.3.19"); MODULE_LICENSE("GPL"); MODULE_SUPPORTED_DEVICE("{{Native Instruments, RigKontrol2}," "{Native Instruments, RigKontrol3}," "{Native Instruments, Kore Controller}," "{Native Instruments, Kore Controller 2}," "{Native Instruments, Audio Kontrol 1}," + "{Native Instruments, Audio 2 DJ}," "{Native Instruments, Audio 4 DJ}," "{Native Instruments, Audio 8 DJ}," "{Native Instruments, Session I/O}," @@ -121,6 +122,11 @@ static struct usb_device_id snd_usb_id_table[] = { .idVendor = USB_VID_NATIVEINSTRUMENTS, .idProduct = USB_PID_AUDIO4DJ }, + { + .match_flags = USB_DEVICE_ID_MATCH_DEVICE, + .idVendor = USB_VID_NATIVEINSTRUMENTS, + .idProduct = USB_PID_AUDIO2DJ + }, { /* terminator */ } }; diff --git a/sound/usb/caiaq/device.h b/sound/usb/caiaq/device.h index ece73514854..44e3edf88be 100644 --- a/sound/usb/caiaq/device.h +++ b/sound/usb/caiaq/device.h @@ -10,6 +10,7 @@ #define USB_PID_KORECONTROLLER 0x4711 #define USB_PID_KORECONTROLLER2 0x4712 #define USB_PID_AK1 0x0815 +#define USB_PID_AUDIO2DJ 0x041c #define USB_PID_AUDIO4DJ 0x0839 #define USB_PID_AUDIO8DJ 0x1978 #define USB_PID_SESSIONIO 0x1915 -- GitLab From 4a19fb11a90fdbbcb3bc02effa036230d035ca28 Mon Sep 17 00:00:00 2001 From: Stefan Bader Date: Thu, 23 Jul 2009 11:26:05 +0200 Subject: [PATCH 0244/1342] jfs: Fix early release of acl in jfs_get_acl BugLink: http://bugs.launchpad.net/ubuntu/+bug/396780 Commit 073aaa1b142461d91f83da66db1184d7c1b1edea "helpers for acl caching + switch to those" introduced new helper functions for acl handling but seems to have introduced a regression for jfs as the acl is released before returning it to the caller, instead of leaving this for the caller to do. This causes the acl object to be used after freeing it, leading to kernel panics in completely different places. Thanks to Christophe Dumez for reporting and bisecting into this. Reported-by: Christophe Dumez Tested-by: Christophe Dumez Signed-off-by: Stefan Bader Acked-by: Andy Whitcroft Signed-off-by: Dave Kleikamp --- fs/jfs/acl.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/fs/jfs/acl.c b/fs/jfs/acl.c index 91fa3ad6e8c..a29c7c3e3fb 100644 --- a/fs/jfs/acl.c +++ b/fs/jfs/acl.c @@ -67,10 +67,8 @@ static struct posix_acl *jfs_get_acl(struct inode *inode, int type) acl = posix_acl_from_xattr(value, size); } kfree(value); - if (!IS_ERR(acl)) { + if (!IS_ERR(acl)) set_cached_acl(inode, type, acl); - posix_acl_release(acl); - } return acl; } -- GitLab From fc4c73554c9d93b3e495f2f7acae1323b0d5db84 Mon Sep 17 00:00:00 2001 From: Matt Fleming Date: Thu, 23 Jul 2009 17:16:14 +0100 Subject: [PATCH 0245/1342] ftrace: Fix the conditional that updates $ref_func Fix the conditional that checks if we already have a $ref_func and that the new function is weak. The code as previously checking whether either condition was false, and we really need to only update $ref_func is both cconditions are false. Signed-off-by: Matt Fleming LKML-Reference: <1248365775-25196-1-git-send-email-matt@console-pimps.org> Signed-off-by: Steven Rostedt --- scripts/recordmcount.pl | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/scripts/recordmcount.pl b/scripts/recordmcount.pl index 7109e2b5bc0..16c5563b412 100755 --- a/scripts/recordmcount.pl +++ b/scripts/recordmcount.pl @@ -414,7 +414,7 @@ while () { $read_function = 0; } else { # if we already have a function, and this is weak, skip it - if (!defined($ref_func) || !defined($weak{$text})) { + if (!defined($ref_func) && !defined($weak{$text})) { $ref_func = $text; } } -- GitLab From bd171d5ffc5cb2ba471e8205c679ee9d12b90116 Mon Sep 17 00:00:00 2001 From: Matt Fleming Date: Thu, 23 Jul 2009 17:16:15 +0100 Subject: [PATCH 0246/1342] ftrace: Only update $offset when we update $ref_func The value of $offset should be the offset of $ref_func from the beginning of the object file. Therefore, we should set both variables together. This fixes a bug I was hitting on sh where $offset (which is used to calcualte the addends for the __mcount_loc entries) was being set multiple times and didn't correspond to $ref_func's offset in the object file. The addends in __mcount_loc were calculated incorrectly, resulting in ftrace dynamically modifying addresses that weren't mcount call sites. Signed-off-by: Matt Fleming LKML-Reference: <1248365775-25196-2-git-send-email-matt@console-pimps.org> Signed-off-by: Steven Rostedt --- scripts/recordmcount.pl | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/scripts/recordmcount.pl b/scripts/recordmcount.pl index 16c5563b412..d29baa2e063 100755 --- a/scripts/recordmcount.pl +++ b/scripts/recordmcount.pl @@ -403,7 +403,6 @@ while () { # section found, now is this a start of a function? } elsif ($read_function && /$function_regex/) { $text_found = 1; - $offset = hex $1; $text = $2; # if this is either a local function or a weak function @@ -412,10 +411,12 @@ while () { if (!defined($locals{$text}) && !defined($weak{$text})) { $ref_func = $text; $read_function = 0; + $offset = hex $1; } else { # if we already have a function, and this is weak, skip it if (!defined($ref_func) && !defined($weak{$text})) { $ref_func = $text; + $offset = hex $1; } } } elsif ($read_headers && /$mcount_section/) { -- GitLab From dacac4da5290ee3f3f413bd6980af2befb813e28 Mon Sep 17 00:00:00 2001 From: Mark Ware Date: Thu, 23 Jul 2009 10:56:48 -0700 Subject: [PATCH 0247/1342] net: Rework mdio-ofgpio driver to use of_mdio infrastructure Changes to the fs_enet driver aa73832c5a80d6c52c69b18af858d88fa595dd3c ("net: Rework fs_enet driver to use of_mdio infrastructure") cause kernel crashes when using the mdio-ofgpio driver. This patch replicates similar changes made to the fs_enet mii-bitbang drivers. It has been tested on a custom mpc8280 based board using an NFS mounted root. Signed-off-by: Mark Ware Acked-by: Grant Likely Signed-off-by: David S. Miller --- drivers/net/phy/mdio-gpio.c | 77 +++++++++++++++++-------------------- 1 file changed, 36 insertions(+), 41 deletions(-) diff --git a/drivers/net/phy/mdio-gpio.c b/drivers/net/phy/mdio-gpio.c index 33984b73723..22cdd451fb8 100644 --- a/drivers/net/phy/mdio-gpio.c +++ b/drivers/net/phy/mdio-gpio.c @@ -30,6 +30,7 @@ #ifdef CONFIG_OF_GPIO #include +#include #include #endif @@ -81,13 +82,12 @@ static struct mdiobb_ops mdio_gpio_ops = { .get_mdio_data = mdio_get, }; -static int __devinit mdio_gpio_bus_init(struct device *dev, +static struct mii_bus * __devinit mdio_gpio_bus_init(struct device *dev, struct mdio_gpio_platform_data *pdata, int bus_id) { struct mii_bus *new_bus; struct mdio_gpio_info *bitbang; - int ret = -ENOMEM; int i; bitbang = kzalloc(sizeof(*bitbang), GFP_KERNEL); @@ -104,8 +104,6 @@ static int __devinit mdio_gpio_bus_init(struct device *dev, new_bus->name = "GPIO Bitbanged MDIO", - ret = -ENODEV; - new_bus->phy_mask = pdata->phy_mask; new_bus->irq = pdata->irqs; new_bus->parent = dev; @@ -129,15 +127,8 @@ static int __devinit mdio_gpio_bus_init(struct device *dev, dev_set_drvdata(dev, new_bus); - ret = mdiobus_register(new_bus); - if (ret) - goto out_free_all; - - return 0; + return new_bus; -out_free_all: - dev_set_drvdata(dev, NULL); - gpio_free(bitbang->mdio); out_free_mdc: gpio_free(bitbang->mdc); out_free_bus: @@ -145,30 +136,47 @@ out_free_bus: out_free_bitbang: kfree(bitbang); out: - return ret; + return NULL; } -static void __devexit mdio_gpio_bus_destroy(struct device *dev) +static void __devinit mdio_gpio_bus_deinit(struct device *dev) { struct mii_bus *bus = dev_get_drvdata(dev); struct mdio_gpio_info *bitbang = bus->priv; - mdiobus_unregister(bus); - free_mdio_bitbang(bus); dev_set_drvdata(dev, NULL); - gpio_free(bitbang->mdc); gpio_free(bitbang->mdio); + gpio_free(bitbang->mdc); + free_mdio_bitbang(bus); kfree(bitbang); } +static void __devexit mdio_gpio_bus_destroy(struct device *dev) +{ + struct mii_bus *bus = dev_get_drvdata(dev); + + mdiobus_unregister(bus); + mdio_gpio_bus_deinit(dev); +} + static int __devinit mdio_gpio_probe(struct platform_device *pdev) { struct mdio_gpio_platform_data *pdata = pdev->dev.platform_data; + struct mii_bus *new_bus; + int ret; if (!pdata) return -ENODEV; - return mdio_gpio_bus_init(&pdev->dev, pdata, pdev->id); + new_bus = mdio_gpio_bus_init(&pdev->dev, pdata, pdev->id); + if (!new_bus) + return -ENODEV; + + ret = mdiobus_register(new_bus); + if (ret) + mdio_gpio_bus_deinit(&pdev->dev); + + return ret; } static int __devexit mdio_gpio_remove(struct platform_device *pdev) @@ -179,29 +187,12 @@ static int __devexit mdio_gpio_remove(struct platform_device *pdev) } #ifdef CONFIG_OF_GPIO -static void __devinit add_phy(struct mdio_gpio_platform_data *pdata, - struct device_node *np) -{ - const u32 *data; - int len, id, irq; - - data = of_get_property(np, "reg", &len); - if (!data || len != 4) - return; - - id = *data; - pdata->phy_mask &= ~(1 << id); - - irq = of_irq_to_resource(np, 0, NULL); - if (irq) - pdata->irqs[id] = irq; -} static int __devinit mdio_ofgpio_probe(struct of_device *ofdev, const struct of_device_id *match) { - struct device_node *np = NULL; struct mdio_gpio_platform_data *pdata; + struct mii_bus *new_bus; int ret; pdata = kzalloc(sizeof(*pdata), GFP_KERNEL); @@ -215,14 +206,18 @@ static int __devinit mdio_ofgpio_probe(struct of_device *ofdev, ret = of_get_gpio(ofdev->node, 1); if (ret < 0) - goto out_free; + goto out_free; pdata->mdio = ret; - while ((np = of_get_next_child(ofdev->node, np))) - if (!strcmp(np->type, "ethernet-phy")) - add_phy(pdata, np); + new_bus = mdio_gpio_bus_init(&ofdev->dev, pdata, pdata->mdc); + if (!new_bus) + return -ENODEV; - return mdio_gpio_bus_init(&ofdev->dev, pdata, pdata->mdc); + ret = of_mdiobus_register(new_bus, ofdev->node); + if (ret) + mdio_gpio_bus_deinit(&ofdev->dev); + + return ret; out_free: kfree(pdata); -- GitLab From 82e12644cf5227dab15201fbcaf0ca6330ebd70f Mon Sep 17 00:00:00 2001 From: Tao Ma Date: Thu, 23 Jul 2009 08:12:58 +0800 Subject: [PATCH 0248/1342] ocfs2: Use ocfs2_rec_clusters in ocfs2_adjust_adjacent_records. In ocfs2_adjust_adjacent_records, we will adjust adjacent records according to the extent_list in the lower level. But actually the lower level tree will either be a leaf or a branch. If we only use ocfs2_is_empty_extent we will meet with some problem if the lower tree is a branch (tree_depth > 1). So use !ocfs2_rec_clusters instead. And actually only the leaf record can have holes. So add a BUG_ON for non-leaf branch. Signed-off-by: Tao Ma Signed-off-by: Joel Becker --- fs/ocfs2/alloc.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/fs/ocfs2/alloc.c b/fs/ocfs2/alloc.c index 11085af7124..f9a3e894266 100644 --- a/fs/ocfs2/alloc.c +++ b/fs/ocfs2/alloc.c @@ -1914,7 +1914,8 @@ static void ocfs2_adjust_adjacent_records(struct ocfs2_extent_rec *left_rec, * immediately to their right. */ left_clusters = le32_to_cpu(right_child_el->l_recs[0].e_cpos); - if (ocfs2_is_empty_extent(&right_child_el->l_recs[0])) { + if (!ocfs2_rec_clusters(right_child_el, &right_child_el->l_recs[0])) { + BUG_ON(right_child_el->l_tree_depth); BUG_ON(le16_to_cpu(right_child_el->l_next_free_rec) <= 1); left_clusters = le32_to_cpu(right_child_el->l_recs[1].e_cpos); } -- GitLab From b57ac2c43e66cb4aa76c9d2d0e9e0e04f19cc5a6 Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Wed, 22 Jul 2009 13:17:15 +0200 Subject: [PATCH 0249/1342] ocfs2: Make global quota files blocksize aligned Change i_size of global quota files so that it always remains aligned to block size. This is mainly because the end of quota block may contain checksum (if checksumming is enabled) and it's a bit awkward for it to be "outside" of quota file (and it makes life harder for ocfs2-tools). Signed-off-by: Jan Kara Signed-off-by: Joel Becker --- fs/ocfs2/quota_global.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) diff --git a/fs/ocfs2/quota_global.c b/fs/ocfs2/quota_global.c index edfa60cd155..a66cb82fd6e 100644 --- a/fs/ocfs2/quota_global.c +++ b/fs/ocfs2/quota_global.c @@ -211,14 +211,17 @@ ssize_t ocfs2_quota_write(struct super_block *sb, int type, mutex_lock_nested(&gqinode->i_mutex, I_MUTEX_QUOTA); if (gqinode->i_size < off + len) { + loff_t rounded_end = + ocfs2_align_bytes_to_blocks(sb, off + len); + down_write(&OCFS2_I(gqinode)->ip_alloc_sem); - err = ocfs2_extend_no_holes(gqinode, off + len, off); + err = ocfs2_extend_no_holes(gqinode, rounded_end, off); up_write(&OCFS2_I(gqinode)->ip_alloc_sem); if (err < 0) goto out; err = ocfs2_simple_size_update(gqinode, oinfo->dqi_gqi_bh, - off + len); + rounded_end); if (err < 0) goto out; new = 1; -- GitLab From 4b3fa1904c0d192461ebba692e4940a334b74353 Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Wed, 22 Jul 2009 13:17:16 +0200 Subject: [PATCH 0250/1342] ocfs2: Mark buffer uptodate before calling ocfs2_journal_access_dq() In a code path extending local quota files we marked new header buffer uptodate only after calling ocfs2_journal_access_dq() which triggers a bug. Fix it and also call ocfs2 variant of the function marking buffer uptodate. Signed-off-by: Jan Kara Signed-off-by: Joel Becker --- fs/ocfs2/quota_local.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/fs/ocfs2/quota_local.c b/fs/ocfs2/quota_local.c index 5a460fa8255..b624f9bc928 100644 --- a/fs/ocfs2/quota_local.c +++ b/fs/ocfs2/quota_local.c @@ -20,6 +20,7 @@ #include "sysfile.h" #include "dlmglue.h" #include "quota.h" +#include "uptodate.h" /* Number of local quota structures per block */ static inline unsigned int ol_quota_entries_per_block(struct super_block *sb) @@ -979,6 +980,8 @@ static struct ocfs2_quota_chunk *ocfs2_local_quota_add_chunk( mlog_errno(status); goto out; } + ocfs2_set_new_buffer_uptodate(lqinode, bh); + dchunk = (struct ocfs2_local_disk_chunk *)bh->b_data; handle = ocfs2_start_trans(OCFS2_SB(sb), 2); @@ -999,7 +1002,6 @@ static struct ocfs2_quota_chunk *ocfs2_local_quota_add_chunk( memset(dchunk->dqc_bitmap, 0, sb->s_blocksize - sizeof(struct ocfs2_local_disk_chunk) - OCFS2_QBLK_RESERVED_SPACE); - set_buffer_uptodate(bh); unlock_buffer(bh); status = ocfs2_journal_dirty(handle, bh); if (status < 0) { -- GitLab From 0e7f387bf386c99e8ee322649fe4fc23b9cccc6c Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Wed, 22 Jul 2009 13:17:17 +0200 Subject: [PATCH 0251/1342] ocfs2: Initialize blocks allocated to local quota file When we extend local quota file, we should initialize data in newly allocated block. Firstly because on recovery we could parse bogus data, secondly so that block checksums are properly computed. Signed-off-by: Jan Kara Signed-off-by: Joel Becker --- fs/ocfs2/quota_local.c | 98 +++++++++++++++++++++++++++++++++++------- 1 file changed, 83 insertions(+), 15 deletions(-) diff --git a/fs/ocfs2/quota_local.c b/fs/ocfs2/quota_local.c index b624f9bc928..9d2993de108 100644 --- a/fs/ocfs2/quota_local.c +++ b/fs/ocfs2/quota_local.c @@ -941,7 +941,7 @@ static struct ocfs2_quota_chunk *ocfs2_local_quota_add_chunk( struct ocfs2_local_disk_chunk *dchunk; int status; handle_t *handle; - struct buffer_head *bh = NULL; + struct buffer_head *bh = NULL, *dbh = NULL; u64 p_blkno; /* We are protected by dqio_sem so no locking needed */ @@ -965,34 +965,32 @@ static struct ocfs2_quota_chunk *ocfs2_local_quota_add_chunk( mlog_errno(status); goto out; } + handle = ocfs2_start_trans(OCFS2_SB(sb), 3); + if (IS_ERR(handle)) { + status = PTR_ERR(handle); + mlog_errno(status); + goto out; + } + /* Initialize chunk header */ down_read(&OCFS2_I(lqinode)->ip_alloc_sem); status = ocfs2_extent_map_get_blocks(lqinode, oinfo->dqi_blocks, &p_blkno, NULL, NULL); up_read(&OCFS2_I(lqinode)->ip_alloc_sem); if (status < 0) { mlog_errno(status); - goto out; + goto out_trans; } bh = sb_getblk(sb, p_blkno); if (!bh) { status = -ENOMEM; mlog_errno(status); - goto out; + goto out_trans; } - ocfs2_set_new_buffer_uptodate(lqinode, bh); - dchunk = (struct ocfs2_local_disk_chunk *)bh->b_data; - - handle = ocfs2_start_trans(OCFS2_SB(sb), 2); - if (IS_ERR(handle)) { - status = PTR_ERR(handle); - mlog_errno(status); - goto out; - } - + ocfs2_set_new_buffer_uptodate(lqinode, bh); status = ocfs2_journal_access_dq(handle, lqinode, bh, - OCFS2_JOURNAL_ACCESS_WRITE); + OCFS2_JOURNAL_ACCESS_CREATE); if (status < 0) { mlog_errno(status); goto out_trans; @@ -1009,6 +1007,38 @@ static struct ocfs2_quota_chunk *ocfs2_local_quota_add_chunk( goto out_trans; } + /* Initialize new block with structures */ + down_read(&OCFS2_I(lqinode)->ip_alloc_sem); + status = ocfs2_extent_map_get_blocks(lqinode, oinfo->dqi_blocks + 1, + &p_blkno, NULL, NULL); + up_read(&OCFS2_I(lqinode)->ip_alloc_sem); + if (status < 0) { + mlog_errno(status); + goto out_trans; + } + dbh = sb_getblk(sb, p_blkno); + if (!dbh) { + status = -ENOMEM; + mlog_errno(status); + goto out_trans; + } + ocfs2_set_new_buffer_uptodate(lqinode, dbh); + status = ocfs2_journal_access_dq(handle, lqinode, dbh, + OCFS2_JOURNAL_ACCESS_CREATE); + if (status < 0) { + mlog_errno(status); + goto out_trans; + } + lock_buffer(dbh); + memset(dbh->b_data, 0, sb->s_blocksize - OCFS2_QBLK_RESERVED_SPACE); + unlock_buffer(dbh); + status = ocfs2_journal_dirty(handle, dbh); + if (status < 0) { + mlog_errno(status); + goto out_trans; + } + + /* Update local quotafile info */ oinfo->dqi_blocks += 2; oinfo->dqi_chunks++; status = ocfs2_local_write_info(sb, type); @@ -1033,6 +1063,7 @@ out_trans: ocfs2_commit_trans(OCFS2_SB(sb), handle); out: brelse(bh); + brelse(dbh); kmem_cache_free(ocfs2_qf_chunk_cachep, chunk); return ERR_PTR(status); } @@ -1050,6 +1081,8 @@ static struct ocfs2_quota_chunk *ocfs2_extend_local_quota_file( struct ocfs2_local_disk_chunk *dchunk; int epb = ol_quota_entries_per_block(sb); unsigned int chunk_blocks; + struct buffer_head *bh; + u64 p_blkno; int status; handle_t *handle; @@ -1077,12 +1110,46 @@ static struct ocfs2_quota_chunk *ocfs2_extend_local_quota_file( mlog_errno(status); goto out; } - handle = ocfs2_start_trans(OCFS2_SB(sb), 2); + + /* Get buffer from the just added block */ + down_read(&OCFS2_I(lqinode)->ip_alloc_sem); + status = ocfs2_extent_map_get_blocks(lqinode, oinfo->dqi_blocks, + &p_blkno, NULL, NULL); + up_read(&OCFS2_I(lqinode)->ip_alloc_sem); + if (status < 0) { + mlog_errno(status); + goto out; + } + bh = sb_getblk(sb, p_blkno); + if (!bh) { + status = -ENOMEM; + mlog_errno(status); + goto out; + } + ocfs2_set_new_buffer_uptodate(lqinode, bh); + + handle = ocfs2_start_trans(OCFS2_SB(sb), 3); if (IS_ERR(handle)) { status = PTR_ERR(handle); mlog_errno(status); goto out; } + /* Zero created block */ + status = ocfs2_journal_access_dq(handle, lqinode, bh, + OCFS2_JOURNAL_ACCESS_CREATE); + if (status < 0) { + mlog_errno(status); + goto out_trans; + } + lock_buffer(bh); + memset(bh->b_data, 0, sb->s_blocksize); + unlock_buffer(bh); + status = ocfs2_journal_dirty(handle, bh); + if (status < 0) { + mlog_errno(status); + goto out_trans; + } + /* Update chunk header */ status = ocfs2_journal_access_dq(handle, lqinode, chunk->qc_headerbh, OCFS2_JOURNAL_ACCESS_WRITE); if (status < 0) { @@ -1099,6 +1166,7 @@ static struct ocfs2_quota_chunk *ocfs2_extend_local_quota_file( mlog_errno(status); goto out_trans; } + /* Update file header */ oinfo->dqi_blocks++; status = ocfs2_local_write_info(sb, type); if (status < 0) { -- GitLab From 7669f54c55df225cbb2db939a6c9f111445ffc1c Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Wed, 22 Jul 2009 13:17:18 +0200 Subject: [PATCH 0252/1342] ocfs2: Zero out padding of on disk dquot structure Padding fields of on-disk dquot structure were not zeroed. Zero them so that it's easier to use them later. Signed-off-by: Jan Kara Signed-off-by: Joel Becker --- fs/ocfs2/quota_global.c | 1 + 1 file changed, 1 insertion(+) diff --git a/fs/ocfs2/quota_global.c b/fs/ocfs2/quota_global.c index a66cb82fd6e..7248db68135 100644 --- a/fs/ocfs2/quota_global.c +++ b/fs/ocfs2/quota_global.c @@ -69,6 +69,7 @@ static void ocfs2_global_mem2diskdqb(void *dp, struct dquot *dquot) d->dqb_curspace = cpu_to_le64(m->dqb_curspace); d->dqb_btime = cpu_to_le64(m->dqb_btime); d->dqb_itime = cpu_to_le64(m->dqb_itime); + d->dqb_pad1 = d->dqb_pad2 = 0; } static int ocfs2_global_is_id(void *dp, struct dquot *dquot) -- GitLab From 1c1d9793ff6720531c0125a28d321f283716e32f Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Wed, 22 Jul 2009 13:17:19 +0200 Subject: [PATCH 0253/1342] ocfs2: Fix initialization of blockcheck stats We just set blockcheck stats to zeros but we should also properly initialize the spinlock there. Signed-off-by: Jan Kara Signed-off-by: Joel Becker --- fs/ocfs2/super.c | 1 + 1 file changed, 1 insertion(+) diff --git a/fs/ocfs2/super.c b/fs/ocfs2/super.c index f2893878f8a..b0ee0fdf799 100644 --- a/fs/ocfs2/super.c +++ b/fs/ocfs2/super.c @@ -777,6 +777,7 @@ static int ocfs2_sb_probe(struct super_block *sb, } di = (struct ocfs2_dinode *) (*bh)->b_data; memset(stats, 0, sizeof(struct ocfs2_blockcheck_stats)); + spin_lock_init(&stats->b_lock); status = ocfs2_verify_volume(di, *bh, blksize, stats); if (status >= 0) goto bail; -- GitLab From 4539f1df25bcd0fdf0d8a5e2c92de6bece83c7a0 Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Wed, 22 Jul 2009 13:17:20 +0200 Subject: [PATCH 0254/1342] ocfs2: Remove syncjiff field from quota info syncjiff is just a converted value of syncms. Some places which are updating syncms forgot to update syncjiff as well. Since the conversion is just a simple division / multiplication and it does not happen frequently, just remove the syncjiff field to avoid forgotten conversions. Signed-off-by: Jan Kara Signed-off-by: Joel Becker --- fs/ocfs2/quota.h | 1 - fs/ocfs2/quota_global.c | 5 ++--- 2 files changed, 2 insertions(+), 4 deletions(-) diff --git a/fs/ocfs2/quota.h b/fs/ocfs2/quota.h index 7365e2e0870..3fb96fcd4c8 100644 --- a/fs/ocfs2/quota.h +++ b/fs/ocfs2/quota.h @@ -50,7 +50,6 @@ struct ocfs2_mem_dqinfo { unsigned int dqi_chunks; /* Number of chunks in local quota file */ unsigned int dqi_blocks; /* Number of blocks allocated for local quota file */ unsigned int dqi_syncms; /* How often should we sync with other nodes */ - unsigned int dqi_syncjiff; /* Precomputed dqi_syncms in jiffies */ struct list_head dqi_chunk; /* List of chunks */ struct inode *dqi_gqinode; /* Global quota file inode */ struct ocfs2_lock_res dqi_gqlock; /* Lock protecting quota information structure */ diff --git a/fs/ocfs2/quota_global.c b/fs/ocfs2/quota_global.c index 7248db68135..dab45467b5f 100644 --- a/fs/ocfs2/quota_global.c +++ b/fs/ocfs2/quota_global.c @@ -346,7 +346,6 @@ int ocfs2_global_read_info(struct super_block *sb, int type) info->dqi_bgrace = le32_to_cpu(dinfo.dqi_bgrace); info->dqi_igrace = le32_to_cpu(dinfo.dqi_igrace); oinfo->dqi_syncms = le32_to_cpu(dinfo.dqi_syncms); - oinfo->dqi_syncjiff = msecs_to_jiffies(oinfo->dqi_syncms); oinfo->dqi_gi.dqi_blocks = le32_to_cpu(dinfo.dqi_blocks); oinfo->dqi_gi.dqi_free_blk = le32_to_cpu(dinfo.dqi_free_blk); oinfo->dqi_gi.dqi_free_entry = le32_to_cpu(dinfo.dqi_free_entry); @@ -356,7 +355,7 @@ int ocfs2_global_read_info(struct super_block *sb, int type) oinfo->dqi_gi.dqi_qtree_depth = qtree_depth(&oinfo->dqi_gi); INIT_DELAYED_WORK(&oinfo->dqi_sync_work, qsync_work_fn); queue_delayed_work(ocfs2_quota_wq, &oinfo->dqi_sync_work, - oinfo->dqi_syncjiff); + msecs_to_jiffies(oinfo->dqi_syncms)); out_err: mlog_exit(status); @@ -611,7 +610,7 @@ static void qsync_work_fn(struct work_struct *work) dquot_scan_active(sb, ocfs2_sync_dquot_helper, oinfo->dqi_type); queue_delayed_work(ocfs2_quota_wq, &oinfo->dqi_sync_work, - oinfo->dqi_syncjiff); + msecs_to_jiffies(oinfo->dqi_syncms)); } /* -- GitLab From 0584974a77796581eb3a64b6c5005edac4a95128 Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Wed, 22 Jul 2009 13:17:21 +0200 Subject: [PATCH 0255/1342] ocfs2: Define credit counts for quota operations Numbers of needed credits for some quota operations were written as raw numbers. Create appropriate defines instead. Signed-off-by: Jan Kara Signed-off-by: Joel Becker --- fs/ocfs2/journal.h | 13 ++++++++++--- fs/ocfs2/quota_global.c | 18 +++++++++++++----- fs/ocfs2/quota_local.c | 16 ++++++++++++---- 3 files changed, 35 insertions(+), 12 deletions(-) diff --git a/fs/ocfs2/journal.h b/fs/ocfs2/journal.h index 81e8abcd246..4a4d3b55fd2 100644 --- a/fs/ocfs2/journal.h +++ b/fs/ocfs2/journal.h @@ -330,20 +330,27 @@ int ocfs2_journal_dirty(handle_t *handle, /* extended attribute block update */ #define OCFS2_XATTR_BLOCK_UPDATE_CREDITS 1 +/* Update of a single quota block */ +#define OCFS2_QUOTA_BLOCK_UPDATE_CREDITS 1 + /* global quotafile inode update, data block */ -#define OCFS2_QINFO_WRITE_CREDITS (OCFS2_INODE_UPDATE_CREDITS + 1) +#define OCFS2_QINFO_WRITE_CREDITS (OCFS2_INODE_UPDATE_CREDITS + \ + OCFS2_QUOTA_BLOCK_UPDATE_CREDITS) +#define OCFS2_LOCAL_QINFO_WRITE_CREDITS OCFS2_QUOTA_BLOCK_UPDATE_CREDITS /* * The two writes below can accidentally see global info dirty due * to set_info() quotactl so make them prepared for the writes. */ /* quota data block, global info */ /* Write to local quota file */ -#define OCFS2_QWRITE_CREDITS (OCFS2_QINFO_WRITE_CREDITS + 1) +#define OCFS2_QWRITE_CREDITS (OCFS2_QINFO_WRITE_CREDITS + \ + OCFS2_QUOTA_BLOCK_UPDATE_CREDITS) /* global quota data block, local quota data block, global quota inode, * global quota info */ -#define OCFS2_QSYNC_CREDITS (OCFS2_INODE_UPDATE_CREDITS + 3) +#define OCFS2_QSYNC_CREDITS (OCFS2_QINFO_WRITE_CREDITS + \ + 2 * OCFS2_QUOTA_BLOCK_UPDATE_CREDITS) static inline int ocfs2_quota_trans_credits(struct super_block *sb) { diff --git a/fs/ocfs2/quota_global.c b/fs/ocfs2/quota_global.c index dab45467b5f..cc8785cf8f6 100644 --- a/fs/ocfs2/quota_global.c +++ b/fs/ocfs2/quota_global.c @@ -648,10 +648,15 @@ int ocfs2_calc_qdel_credits(struct super_block *sb, int type) return 0; oinfo = sb_dqinfo(sb, type)->dqi_priv; - /* We modify tree, leaf block, global info, local chunk header, - * global and local inode */ - return oinfo->dqi_gi.dqi_qtree_depth + 2 + 1 + - 2 * OCFS2_INODE_UPDATE_CREDITS; + /* + * We modify tree, leaf block, global info, local chunk header, + * global and local inode; OCFS2_QINFO_WRITE_CREDITS already + * accounts for inode update + */ + return oinfo->dqi_gi.dqi_qtree_depth + + OCFS2_QINFO_WRITE_CREDITS + + 2 * OCFS2_QUOTA_BLOCK_UPDATE_CREDITS + + OCFS2_INODE_UPDATE_CREDITS; } static int ocfs2_release_dquot(struct dquot *dquot) @@ -701,7 +706,10 @@ int ocfs2_calc_qinit_credits(struct super_block *sb, int type) * global file we can modify info, tree and leaf block */ return ocfs2_calc_extend_credits(sb, &lfe->id2.i_list, 0) + ocfs2_calc_extend_credits(sb, &gfe->id2.i_list, 0) + - 3 + oinfo->dqi_gi.dqi_qtree_depth + 2; + OCFS2_LOCAL_QINFO_WRITE_CREDITS + + 2 * OCFS2_QUOTA_BLOCK_UPDATE_CREDITS + + oinfo->dqi_gi.dqi_qtree_depth + + 2 * OCFS2_QUOTA_BLOCK_UPDATE_CREDITS; } static int ocfs2_acquire_dquot(struct dquot *dquot) diff --git a/fs/ocfs2/quota_local.c b/fs/ocfs2/quota_local.c index 9d2993de108..bdb09cb6e1f 100644 --- a/fs/ocfs2/quota_local.c +++ b/fs/ocfs2/quota_local.c @@ -101,7 +101,8 @@ static int ocfs2_modify_bh(struct inode *inode, struct buffer_head *bh, handle_t *handle; int status; - handle = ocfs2_start_trans(OCFS2_SB(sb), 1); + handle = ocfs2_start_trans(OCFS2_SB(sb), + OCFS2_QUOTA_BLOCK_UPDATE_CREDITS); if (IS_ERR(handle)) { status = PTR_ERR(handle); mlog_errno(status); @@ -611,7 +612,8 @@ int ocfs2_finish_quota_recovery(struct ocfs2_super *osb, goto out_bh; /* Mark quota file as clean if we are recovering quota file of * some other node. */ - handle = ocfs2_start_trans(osb, 1); + handle = ocfs2_start_trans(osb, + OCFS2_LOCAL_QINFO_WRITE_CREDITS); if (IS_ERR(handle)) { status = PTR_ERR(handle); mlog_errno(status); @@ -965,7 +967,10 @@ static struct ocfs2_quota_chunk *ocfs2_local_quota_add_chunk( mlog_errno(status); goto out; } - handle = ocfs2_start_trans(OCFS2_SB(sb), 3); + /* Local quota info and two new blocks we initialize */ + handle = ocfs2_start_trans(OCFS2_SB(sb), + OCFS2_LOCAL_QINFO_WRITE_CREDITS + + 2 * OCFS2_QUOTA_BLOCK_UPDATE_CREDITS); if (IS_ERR(handle)) { status = PTR_ERR(handle); mlog_errno(status); @@ -1128,7 +1133,10 @@ static struct ocfs2_quota_chunk *ocfs2_extend_local_quota_file( } ocfs2_set_new_buffer_uptodate(lqinode, bh); - handle = ocfs2_start_trans(OCFS2_SB(sb), 3); + /* Local quota info, chunk header and the new block we initialize */ + handle = ocfs2_start_trans(OCFS2_SB(sb), + OCFS2_LOCAL_QINFO_WRITE_CREDITS + + 2 * OCFS2_QUOTA_BLOCK_UPDATE_CREDITS); if (IS_ERR(handle)) { status = PTR_ERR(handle); mlog_errno(status); -- GitLab From 0d5515894fd5b9e9402ef76e9a7e704fd26e0e5f Mon Sep 17 00:00:00 2001 From: Yi Zou Date: Wed, 22 Jul 2009 14:07:12 +0000 Subject: [PATCH 0256/1342] ixgbe: Enable FCoE offload when DCB is enabled for 82599 Currently, FCoE offload feature is turned on when the kernel config has CONFIG_FCOE or CONFIG_FCOE_MODULE set. However, we really want to turn FCoE offload on when there is FCoE traffic passing and turn it off when it's just LAN traffic. Since FCoE depends on a lossless network provided by DCB, this allows us to have FCoE turned on/off when user turns on DCB using dcbtool. Signed-off-by: Yi Zou Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe.h | 1 + drivers/net/ixgbe/ixgbe_dcb_nl.c | 24 ++++++++++++++++++++++++ drivers/net/ixgbe/ixgbe_main.c | 16 ++++++---------- 3 files changed, 31 insertions(+), 10 deletions(-) diff --git a/drivers/net/ixgbe/ixgbe.h b/drivers/net/ixgbe/ixgbe.h index cd22323cfd2..1b12c7ba275 100644 --- a/drivers/net/ixgbe/ixgbe.h +++ b/drivers/net/ixgbe/ixgbe.h @@ -327,6 +327,7 @@ struct ixgbe_adapter { #define IXGBE_FLAG_IN_SFP_MOD_TASK (u32)(1 << 25) #define IXGBE_FLAG_FDIR_HASH_CAPABLE (u32)(1 << 26) #define IXGBE_FLAG_FDIR_PERFECT_CAPABLE (u32)(1 << 27) +#define IXGBE_FLAG_FCOE_CAPABLE (u32)(1 << 28) #define IXGBE_FLAG_FCOE_ENABLED (u32)(1 << 29) u32 flags2; diff --git a/drivers/net/ixgbe/ixgbe_dcb_nl.c b/drivers/net/ixgbe/ixgbe_dcb_nl.c index da2c8514b8d..1c726573290 100644 --- a/drivers/net/ixgbe/ixgbe_dcb_nl.c +++ b/drivers/net/ixgbe/ixgbe_dcb_nl.c @@ -139,6 +139,18 @@ static u8 ixgbe_dcbnl_set_state(struct net_device *netdev, u8 state) adapter->flags &= ~IXGBE_FLAG_FDIR_PERFECT_CAPABLE; } adapter->flags |= IXGBE_FLAG_DCB_ENABLED; +#ifdef IXGBE_FCOE + /* Turn on FCoE offload */ + if ((adapter->flags & IXGBE_FLAG_FCOE_CAPABLE) && + (!(adapter->flags & IXGBE_FLAG_FCOE_ENABLED))) { + adapter->flags |= IXGBE_FLAG_FCOE_ENABLED; + adapter->ring_feature[RING_F_FCOE].indices = + IXGBE_FCRETA_SIZE; + netdev->features |= NETIF_F_FCOE_CRC; + netdev->features |= NETIF_F_FSO; + netdev->fcoe_ddp_xid = IXGBE_FCOE_DDP_MAX - 1; + } +#endif /* IXGBE_FCOE */ ixgbe_init_interrupt_scheme(adapter); if (netif_running(netdev)) netdev->netdev_ops->ndo_open(netdev); @@ -156,6 +168,18 @@ static u8 ixgbe_dcbnl_set_state(struct net_device *netdev, u8 state) adapter->flags |= IXGBE_FLAG_RSS_ENABLED; if (adapter->hw.mac.type == ixgbe_mac_82599EB) adapter->flags |= IXGBE_FLAG_FDIR_HASH_CAPABLE; + +#ifdef IXGBE_FCOE + /* Turn off FCoE offload */ + if (adapter->flags & (IXGBE_FLAG_FCOE_CAPABLE | + IXGBE_FLAG_FCOE_ENABLED)) { + adapter->flags &= ~IXGBE_FLAG_FCOE_ENABLED; + adapter->ring_feature[RING_F_FCOE].indices = 0; + netdev->features &= ~NETIF_F_FCOE_CRC; + netdev->features &= ~NETIF_F_FSO; + netdev->fcoe_ddp_xid = 0; + } +#endif /* IXGBE_FCOE */ ixgbe_init_interrupt_scheme(adapter); if (netif_running(netdev)) netdev->netdev_ops->ndo_open(netdev); diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index e3442f47f93..a2119d79ccd 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -3806,8 +3806,9 @@ static int __devinit ixgbe_sw_init(struct ixgbe_adapter *adapter) adapter->atr_sample_rate = 20; adapter->fdir_pballoc = 0; #ifdef IXGBE_FCOE - adapter->flags |= IXGBE_FLAG_FCOE_ENABLED; - adapter->ring_feature[RING_F_FCOE].indices = IXGBE_FCRETA_SIZE; + adapter->flags |= IXGBE_FLAG_FCOE_CAPABLE; + adapter->flags &= ~IXGBE_FLAG_FCOE_ENABLED; + adapter->ring_feature[RING_F_FCOE].indices = 0; #endif /* IXGBE_FCOE */ } @@ -5580,16 +5581,11 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev, #endif #ifdef IXGBE_FCOE - if (adapter->flags & IXGBE_FLAG_FCOE_ENABLED) { + if (adapter->flags & IXGBE_FLAG_FCOE_CAPABLE) { if (hw->mac.ops.get_device_caps) { hw->mac.ops.get_device_caps(hw, &device_caps); - if (!(device_caps & IXGBE_DEVICE_CAPS_FCOE_OFFLOADS)) { - netdev->features |= NETIF_F_FCOE_CRC; - netdev->features |= NETIF_F_FSO; - netdev->fcoe_ddp_xid = IXGBE_FCOE_DDP_MAX - 1; - } else { - adapter->flags &= ~IXGBE_FLAG_FCOE_ENABLED; - } + if (device_caps & IXGBE_DEVICE_CAPS_FCOE_OFFLOADS) + adapter->flags &= ~IXGBE_FLAG_FCOE_CAPABLE; } } #endif /* IXGBE_FCOE */ -- GitLab From 601278659d5717b4f7a14fbc9f2b9d559bba6aef Mon Sep 17 00:00:00 2001 From: Lucy Liu Date: Wed, 22 Jul 2009 14:07:33 +0000 Subject: [PATCH 0257/1342] ixgbe: Don't priority tag control frames in DCB mode Certain types of control packets (LLDP, LACP, etc.) are not supposed to have a priority tag or vlan tag inserted. Ixgbe driver is currently priority tagging everything (if packet is not on a VLAN interface). This patch modifies DCB mode, so that packets marked with skb priority TC_PRIO_CONTROL are not priority tagged. It also transmits these packets on the highest priority traffic class. Programs (like dcbd) can set the skb priority using a socket option. Or, a tc filter can be configured to set the priority value. Using the value TC_PRIO_CONTROL (7) has the benefit that it is already defined in the kernel, and the bonding LACP code already sets the skb->priority field to this value. Signed-off-by: Lucy Liu Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_main.c | 18 ++++++++++++------ 1 file changed, 12 insertions(+), 6 deletions(-) diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index a2119d79ccd..47a3c6d7056 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -34,6 +34,7 @@ #include #include #include +#include #include #include #include @@ -5126,9 +5127,6 @@ static int ixgbe_xmit_frame(struct sk_buff *skb, struct net_device *netdev) int count = 0; unsigned int f; - r_idx = skb->queue_mapping; - tx_ring = &adapter->tx_ring[r_idx]; - if (adapter->vlgrp && vlan_tx_tag_present(skb)) { tx_flags |= vlan_tx_tag_get(skb); if (adapter->flags & IXGBE_FLAG_DCB_ENABLED) { @@ -5138,11 +5136,19 @@ static int ixgbe_xmit_frame(struct sk_buff *skb, struct net_device *netdev) tx_flags <<= IXGBE_TX_FLAGS_VLAN_SHIFT; tx_flags |= IXGBE_TX_FLAGS_VLAN; } else if (adapter->flags & IXGBE_FLAG_DCB_ENABLED) { - tx_flags |= (skb->queue_mapping << 13); - tx_flags <<= IXGBE_TX_FLAGS_VLAN_SHIFT; - tx_flags |= IXGBE_TX_FLAGS_VLAN; + if (skb->priority != TC_PRIO_CONTROL) { + tx_flags |= (skb->queue_mapping << 13); + tx_flags <<= IXGBE_TX_FLAGS_VLAN_SHIFT; + tx_flags |= IXGBE_TX_FLAGS_VLAN; + } else { + skb->queue_mapping = + adapter->ring_feature[RING_F_DCB].indices-1; + } } + r_idx = skb->queue_mapping; + tx_ring = &adapter->tx_ring[r_idx]; + if ((adapter->flags & IXGBE_FLAG_FCOE_ENABLED) && (skb->protocol == htons(ETH_P_FCOE))) tx_flags |= IXGBE_TX_FLAGS_FCOE; -- GitLab From ffafa60d496f80c250f2ae0340ae94434c0b0b4d Mon Sep 17 00:00:00 2001 From: Andy Gospodarek Date: Wed, 22 Jul 2009 09:34:00 +0000 Subject: [PATCH 0258/1342] ixgbe: remove unnecessary call to device_init_wakeup Calls to device_init_wakeup should not be necessary in drivers that use device_set_wakeup_enable since pci_pm_init will set the can_wakeup flag for the device when initialized. Signed-off-by: Andy Gospodarek Acked-by: Peter P Waskiewicz Jr Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_main.c | 1 - 1 file changed, 1 deletion(-) diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index 47a3c6d7056..68877599f6d 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -5640,7 +5640,6 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev, adapter->wol = 0; break; } - device_init_wakeup(&adapter->pdev->dev, true); device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol); /* pick up the PCI bus settings for reporting later */ -- GitLab From 69885683d22d8c05910fd808c01fdce1322739b4 Mon Sep 17 00:00:00 2001 From: Mikulas Patocka Date: Thu, 23 Jul 2009 20:30:37 +0100 Subject: [PATCH 0259/1342] dm raid1: wake kmirrord when requeueing delayed bios after remote recovery The recent commit 7513c2a761d69d2a93f17146b3563527d3618ba0 (dm raid1: add is_remote_recovering hook for clusters) changed do_writes() to update the ms->writes list but forgot to wake up kmirrord to process it. The rule is that when anything is being added on ms->reads, ms->writes or ms->failures and the list was empty before we must call wakeup_mirrord (for immediate processing) or delayed_wake (for delayed processing). Otherwise the bios could sit on the list indefinitely. Signed-off-by: Mikulas Patocka CC: stable@kernel.org Signed-off-by: Alasdair G Kergon --- drivers/md/dm-raid1.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/md/dm-raid1.c b/drivers/md/dm-raid1.c index ce8868c768c..42a3e4341d6 100644 --- a/drivers/md/dm-raid1.c +++ b/drivers/md/dm-raid1.c @@ -638,6 +638,7 @@ static void do_writes(struct mirror_set *ms, struct bio_list *writes) spin_lock_irq(&ms->lock); bio_list_merge(&ms->writes, &requeue); spin_unlock_irq(&ms->lock); + delayed_wake(ms); } /* -- GitLab From a732c207d19e899845ae47139708af898daaf9fd Mon Sep 17 00:00:00 2001 From: Mike Snitzer Date: Thu, 23 Jul 2009 20:30:40 +0100 Subject: [PATCH 0260/1342] dm: remove queue next_ordered workaround for barriers This patch removes DM's bio-based vs request-based conditional setting of next_ordered. For bio-based DM the next_ordered check is no longer a concern (as that check is now in the __make_request path). For request-based DM the default of QUEUE_ORDERED_NONE is now appropriate. bio-based DM was changed to work-around the previously misplaced next_ordered check with this commit: 99360b4c18f7675b50d283301d46d755affe75fd request-based DM does not yet support barriers but reacted to the above bio-based DM change with this commit: 5d67aa2366ccb8257d103d0b43df855605c3c086 The above changes are no longer needed given Neil Brown's recent fix to put the next_ordered check in the __make_request path: db64f680ba4b5c56c4be59f0698000df89ff0281 Signed-off-by: Mike Snitzer Cc: Jun'ichi Nomura Cc: NeilBrown Acked-by: Kiyoshi Ueda Acked-by: Mikulas Patocka Signed-off-by: Alasdair G Kergon --- drivers/md/dm-table.c | 5 ----- drivers/md/dm.c | 10 ---------- drivers/md/dm.h | 1 - 3 files changed, 16 deletions(-) diff --git a/drivers/md/dm-table.c b/drivers/md/dm-table.c index 2cba557d9e6..5d16d06613a 100644 --- a/drivers/md/dm-table.c +++ b/drivers/md/dm-table.c @@ -830,11 +830,6 @@ unsigned dm_table_get_type(struct dm_table *t) return t->type; } -bool dm_table_bio_based(struct dm_table *t) -{ - return dm_table_get_type(t) == DM_TYPE_BIO_BASED; -} - bool dm_table_request_based(struct dm_table *t) { return dm_table_get_type(t) == DM_TYPE_REQUEST_BASED; diff --git a/drivers/md/dm.c b/drivers/md/dm.c index 9acd54a5cff..8a311ea0d44 100644 --- a/drivers/md/dm.c +++ b/drivers/md/dm.c @@ -2203,16 +2203,6 @@ int dm_swap_table(struct mapped_device *md, struct dm_table *table) goto out; } - /* - * It is enought that blk_queue_ordered() is called only once when - * the first bio-based table is bound. - * - * This setting should be moved to alloc_dev() when request-based dm - * supports barrier. - */ - if (!md->map && dm_table_bio_based(table)) - blk_queue_ordered(md->queue, QUEUE_ORDERED_DRAIN, NULL); - __unbind(md); r = __bind(md, table, &limits); diff --git a/drivers/md/dm.h b/drivers/md/dm.h index 23278ae80f0..a7663eba17e 100644 --- a/drivers/md/dm.h +++ b/drivers/md/dm.h @@ -61,7 +61,6 @@ int dm_table_any_congested(struct dm_table *t, int bdi_bits); int dm_table_any_busy_target(struct dm_table *t); int dm_table_set_type(struct dm_table *t); unsigned dm_table_get_type(struct dm_table *t); -bool dm_table_bio_based(struct dm_table *t); bool dm_table_request_based(struct dm_table *t); int dm_table_alloc_md_mempools(struct dm_table *t); void dm_table_free_md_mempools(struct dm_table *t); -- GitLab From 5dea271b6d87bd1d79a59c1d5baac2596a841c37 Mon Sep 17 00:00:00 2001 From: Mike Snitzer Date: Thu, 23 Jul 2009 20:30:42 +0100 Subject: [PATCH 0261/1342] dm table: pass correct dev area size to device_area_is_valid Incorrect device area lengths are being passed to device_area_is_valid(). The regression appeared in 2.6.31-rc1 through commit 754c5fc7ebb417b23601a6222a6005cc2e7f2913. With the dm-stripe target, the size of the target (ti->len) was used instead of the stripe_width (ti->len/#stripes). An example of a consequent incorrect error message is: device-mapper: table: 254:0: sdb too small for target Signed-off-by: Mike Snitzer Signed-off-by: Alasdair G Kergon --- drivers/md/dm-crypt.c | 2 +- drivers/md/dm-delay.c | 4 ++-- drivers/md/dm-linear.c | 2 +- drivers/md/dm-mpath.c | 2 +- drivers/md/dm-raid1.c | 2 +- drivers/md/dm-stripe.c | 7 ++++--- drivers/md/dm-table.c | 10 +++++----- include/linux/device-mapper.h | 4 ++-- 8 files changed, 17 insertions(+), 16 deletions(-) diff --git a/drivers/md/dm-crypt.c b/drivers/md/dm-crypt.c index 529e2ba505c..ed103816401 100644 --- a/drivers/md/dm-crypt.c +++ b/drivers/md/dm-crypt.c @@ -1318,7 +1318,7 @@ static int crypt_iterate_devices(struct dm_target *ti, { struct crypt_config *cc = ti->private; - return fn(ti, cc->dev, cc->start, data); + return fn(ti, cc->dev, cc->start, ti->len, data); } static struct target_type crypt_target = { diff --git a/drivers/md/dm-delay.c b/drivers/md/dm-delay.c index 4e5b843cd4d..ebe7381f47c 100644 --- a/drivers/md/dm-delay.c +++ b/drivers/md/dm-delay.c @@ -324,12 +324,12 @@ static int delay_iterate_devices(struct dm_target *ti, struct delay_c *dc = ti->private; int ret = 0; - ret = fn(ti, dc->dev_read, dc->start_read, data); + ret = fn(ti, dc->dev_read, dc->start_read, ti->len, data); if (ret) goto out; if (dc->dev_write) - ret = fn(ti, dc->dev_write, dc->start_write, data); + ret = fn(ti, dc->dev_write, dc->start_write, ti->len, data); out: return ret; diff --git a/drivers/md/dm-linear.c b/drivers/md/dm-linear.c index 9184b6deb86..82f7d6e6b1e 100644 --- a/drivers/md/dm-linear.c +++ b/drivers/md/dm-linear.c @@ -139,7 +139,7 @@ static int linear_iterate_devices(struct dm_target *ti, { struct linear_c *lc = ti->private; - return fn(ti, lc->dev, lc->start, data); + return fn(ti, lc->dev, lc->start, ti->len, data); } static struct target_type linear_target = { diff --git a/drivers/md/dm-mpath.c b/drivers/md/dm-mpath.c index c70604a2089..6f0d90d4a54 100644 --- a/drivers/md/dm-mpath.c +++ b/drivers/md/dm-mpath.c @@ -1453,7 +1453,7 @@ static int multipath_iterate_devices(struct dm_target *ti, list_for_each_entry(pg, &m->priority_groups, list) { list_for_each_entry(p, &pg->pgpaths, list) { - ret = fn(ti, p->path.dev, ti->begin, data); + ret = fn(ti, p->path.dev, ti->begin, ti->len, data); if (ret) goto out; } diff --git a/drivers/md/dm-raid1.c b/drivers/md/dm-raid1.c index 42a3e4341d6..9726577cde4 100644 --- a/drivers/md/dm-raid1.c +++ b/drivers/md/dm-raid1.c @@ -1293,7 +1293,7 @@ static int mirror_iterate_devices(struct dm_target *ti, for (i = 0; !ret && i < ms->nr_mirrors; i++) ret = fn(ti, ms->mirror[i].dev, - ms->mirror[i].offset, data); + ms->mirror[i].offset, ti->len, data); return ret; } diff --git a/drivers/md/dm-stripe.c b/drivers/md/dm-stripe.c index b240e85ae39..4e0e5937e42 100644 --- a/drivers/md/dm-stripe.c +++ b/drivers/md/dm-stripe.c @@ -320,10 +320,11 @@ static int stripe_iterate_devices(struct dm_target *ti, int ret = 0; unsigned i = 0; - do + do { ret = fn(ti, sc->stripe[i].dev, - sc->stripe[i].physical_start, data); - while (!ret && ++i < sc->stripes); + sc->stripe[i].physical_start, + sc->stripe_width, data); + } while (!ret && ++i < sc->stripes); return ret; } diff --git a/drivers/md/dm-table.c b/drivers/md/dm-table.c index 5d16d06613a..d952b344191 100644 --- a/drivers/md/dm-table.c +++ b/drivers/md/dm-table.c @@ -346,7 +346,7 @@ static void close_dev(struct dm_dev_internal *d, struct mapped_device *md) * If possible, this checks an area of a destination device is valid. */ static int device_area_is_valid(struct dm_target *ti, struct dm_dev *dev, - sector_t start, void *data) + sector_t start, sector_t len, void *data) { struct queue_limits *limits = data; struct block_device *bdev = dev->bdev; @@ -359,7 +359,7 @@ static int device_area_is_valid(struct dm_target *ti, struct dm_dev *dev, if (!dev_size) return 1; - if ((start >= dev_size) || (start + ti->len > dev_size)) { + if ((start >= dev_size) || (start + len > dev_size)) { DMWARN("%s: %s too small for target", dm_device_name(ti->table->md), bdevname(bdev, b)); return 0; @@ -377,11 +377,11 @@ static int device_area_is_valid(struct dm_target *ti, struct dm_dev *dev, return 0; } - if (ti->len & (logical_block_size_sectors - 1)) { + if (len & (logical_block_size_sectors - 1)) { DMWARN("%s: len=%llu not aligned to h/w " "logical block size %hu of %s", dm_device_name(ti->table->md), - (unsigned long long)ti->len, + (unsigned long long)len, limits->logical_block_size, bdevname(bdev, b)); return 0; } @@ -482,7 +482,7 @@ static int __table_get_device(struct dm_table *t, struct dm_target *ti, #define min_not_zero(l, r) (l == 0) ? r : ((r == 0) ? l : min(l, r)) int dm_set_device_limits(struct dm_target *ti, struct dm_dev *dev, - sector_t start, void *data) + sector_t start, sector_t len, void *data) { struct queue_limits *limits = data; struct block_device *bdev = dev->bdev; diff --git a/include/linux/device-mapper.h b/include/linux/device-mapper.h index 0d6310657f3..655e7721580 100644 --- a/include/linux/device-mapper.h +++ b/include/linux/device-mapper.h @@ -84,7 +84,7 @@ typedef int (*dm_merge_fn) (struct dm_target *ti, struct bvec_merge_data *bvm, typedef int (*iterate_devices_callout_fn) (struct dm_target *ti, struct dm_dev *dev, - sector_t physical_start, + sector_t start, sector_t len, void *data); typedef int (*dm_iterate_devices_fn) (struct dm_target *ti, @@ -104,7 +104,7 @@ void dm_error(const char *message); * Combine device limits. */ int dm_set_device_limits(struct dm_target *ti, struct dm_dev *dev, - sector_t start, void *data); + sector_t start, sector_t len, void *data); struct dm_dev { struct block_device *bdev; -- GitLab From d6c585a4342a2ff627a29f9aea77c5ed4cd76023 Mon Sep 17 00:00:00 2001 From: Thomas Gleixner Date: Fri, 24 Jul 2009 08:34:59 +0200 Subject: [PATCH 0262/1342] x86: geode: Mark mfgpt irq IRQF_TIMER to prevent resume failure Timer interrupts are excluded from being disabled during suspend. The clock events code manages the disabling of clock events on its own because the timer interrupt needs to be functional before the resume code reenables the device interrupts. The mfgpt timer request its interrupt without setting the IRQF_TIMER flag so suspend_device_irqs() disables it as well which results in a fatal resume failure. Adding IRQF_TIMER to the interupt flags when requesting the mrgpt timer interrupt solves the problem. Signed-off-by: Thomas Gleixner LKML-Reference: Cc: Andres Salomon Cc: stable@kernel.org --- arch/x86/kernel/mfgpt_32.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/mfgpt_32.c b/arch/x86/kernel/mfgpt_32.c index 846510b78a0..2a62d843f01 100644 --- a/arch/x86/kernel/mfgpt_32.c +++ b/arch/x86/kernel/mfgpt_32.c @@ -347,7 +347,7 @@ static irqreturn_t mfgpt_tick(int irq, void *dev_id) static struct irqaction mfgptirq = { .handler = mfgpt_tick, - .flags = IRQF_DISABLED | IRQF_NOBALANCING, + .flags = IRQF_DISABLED | IRQF_NOBALANCING | IRQF_TIMER, .name = "mfgpt-timer" }; -- GitLab From 5f954c3426190f7ae432a09abd62164d5d14c709 Mon Sep 17 00:00:00 2001 From: Heiko Carstens Date: Fri, 24 Jul 2009 12:39:49 +0200 Subject: [PATCH 0263/1342] [S390] hibernation: fix lowcore handling Our swsusp_arch_suspend() backend implementation disables prefixing by setting the contents of the prefix register to 0. However afterwards common code functions are called which might access percpu data structures. Since the lowcore contains e.g. the percpu base pointer this isn't a good idea. So fix this by copying the hibernating cpu's lowcore to absolute address zero. Signed-off-by: Heiko Carstens Signed-off-by: Martin Schwidefsky --- arch/s390/kernel/early.c | 4 ++-- arch/s390/power/swsusp_asm64.S | 13 ++++++++----- 2 files changed, 10 insertions(+), 7 deletions(-) diff --git a/arch/s390/kernel/early.c b/arch/s390/kernel/early.c index f9b144049dc..8d15314381e 100644 --- a/arch/s390/kernel/early.c +++ b/arch/s390/kernel/early.c @@ -210,7 +210,7 @@ static noinline __init void detect_machine_type(void) machine_flags |= MACHINE_FLAG_VM; } -static void early_pgm_check_handler(void) +static __init void early_pgm_check_handler(void) { unsigned long addr; const struct exception_table_entry *fixup; @@ -222,7 +222,7 @@ static void early_pgm_check_handler(void) S390_lowcore.program_old_psw.addr = fixup->fixup | PSW_ADDR_AMODE; } -void setup_lowcore_early(void) +static noinline __init void setup_lowcore_early(void) { psw_t psw; diff --git a/arch/s390/power/swsusp_asm64.S b/arch/s390/power/swsusp_asm64.S index 76d688da32f..e27bd316489 100644 --- a/arch/s390/power/swsusp_asm64.S +++ b/arch/s390/power/swsusp_asm64.S @@ -40,11 +40,11 @@ swsusp_arch_suspend: /* Store prefix register on stack */ stpx __SF_EMPTY(%r15) - /* Setup base register for lowcore (absolute 0) */ - llgf %r1,__SF_EMPTY(%r15) + /* Save prefix register contents for lowcore */ + llgf %r4,__SF_EMPTY(%r15) /* Get pointer to save area */ - aghi %r1,0x1000 + lghi %r1,0x1000 /* Store registers */ mvc 0x318(4,%r1),__SF_EMPTY(%r15) /* move prefix to lowcore */ @@ -79,8 +79,11 @@ swsusp_arch_suspend: xc __SF_EMPTY(4,%r15),__SF_EMPTY(%r15) spx __SF_EMPTY(%r15) - /* Setup lowcore */ - brasl %r14,setup_lowcore_early + lghi %r2,0 + lghi %r3,2*PAGE_SIZE + lghi %r5,2*PAGE_SIZE +1: mvcle %r2,%r4,0 + jo 1b /* Save image */ brasl %r14,swsusp_save -- GitLab From c63b196afcf22405527abe4c2c57926a5bbd6fc9 Mon Sep 17 00:00:00 2001 From: Heiko Carstens Date: Fri, 24 Jul 2009 12:39:50 +0200 Subject: [PATCH 0264/1342] [S390] hibernation: fix register corruption on machine checks swsusp_arch_suspend() actually saves all cpu register contents on hibernation. Machine checks must be disabled since swsusp_arch_suspend() stores register contents to their lowcore save areas. That's the same place where register contents on machine checks would be saved. To avoid register corruption disable machine checks. We must also disable machine checks in the new psw mask for program checks, since swsusp_arch_suspend() may generate program checks. Signed-off-by: Heiko Carstens Signed-off-by: Martin Schwidefsky --- arch/s390/power/swsusp.c | 36 ++++++++++++++++++++++------------ arch/s390/power/swsusp_asm64.S | 22 +-------------------- 2 files changed, 25 insertions(+), 33 deletions(-) diff --git a/arch/s390/power/swsusp.c b/arch/s390/power/swsusp.c index e6a4fe9f5f2..bd1f5c6b0b8 100644 --- a/arch/s390/power/swsusp.c +++ b/arch/s390/power/swsusp.c @@ -7,24 +7,36 @@ * */ +#include -/* - * save CPU registers before creating a hibernation image and before - * restoring the memory state from it - */ void save_processor_state(void) { - /* implentation contained in the - * swsusp_arch_suspend function + /* swsusp_arch_suspend() actually saves all cpu register contents. + * Machine checks must be disabled since swsusp_arch_suspend() stores + * register contents to their lowcore save areas. That's the same + * place where register contents on machine checks would be saved. + * To avoid register corruption disable machine checks. + * We must also disable machine checks in the new psw mask for + * program checks, since swsusp_arch_suspend() may generate program + * checks. Disabling machine checks for all other new psw masks is + * just paranoia. */ + local_mcck_disable(); + /* Disable lowcore protection */ + __ctl_clear_bit(0,28); + S390_lowcore.external_new_psw.mask &= ~PSW_MASK_MCHECK; + S390_lowcore.svc_new_psw.mask &= ~PSW_MASK_MCHECK; + S390_lowcore.io_new_psw.mask &= ~PSW_MASK_MCHECK; + S390_lowcore.program_new_psw.mask &= ~PSW_MASK_MCHECK; } -/* - * restore the contents of CPU registers - */ void restore_processor_state(void) { - /* implentation contained in the - * swsusp_arch_resume function - */ + S390_lowcore.external_new_psw.mask |= PSW_MASK_MCHECK; + S390_lowcore.svc_new_psw.mask |= PSW_MASK_MCHECK; + S390_lowcore.io_new_psw.mask |= PSW_MASK_MCHECK; + S390_lowcore.program_new_psw.mask |= PSW_MASK_MCHECK; + /* Enable lowcore protection */ + __ctl_set_bit(0,28); + local_mcck_enable(); } diff --git a/arch/s390/power/swsusp_asm64.S b/arch/s390/power/swsusp_asm64.S index e27bd316489..b26df5c5933 100644 --- a/arch/s390/power/swsusp_asm64.S +++ b/arch/s390/power/swsusp_asm64.S @@ -32,11 +32,6 @@ swsusp_arch_suspend: /* Deactivate DAT */ stnsm __SF_EMPTY(%r15),0xfb - /* Switch off lowcore protection */ - stctg %c0,%c0,__SF_EMPTY(%r15) - ni __SF_EMPTY+4(%r15),0xef - lctlg %c0,%c0,__SF_EMPTY(%r15) - /* Store prefix register on stack */ stpx __SF_EMPTY(%r15) @@ -88,11 +83,6 @@ swsusp_arch_suspend: /* Save image */ brasl %r14,swsusp_save - /* Switch on lowcore protection */ - stctg %c0,%c0,__SF_EMPTY(%r15) - oi __SF_EMPTY+4(%r15),0x10 - lctlg %c0,%c0,__SF_EMPTY(%r15) - /* Restore prefix register and return */ lghi %r1,0x1000 spx 0x318(%r1) @@ -120,11 +110,6 @@ swsusp_arch_resume: /* Deactivate DAT */ stnsm __SF_EMPTY(%r15),0xfb - /* Switch off lowcore protection */ - stctg %c0,%c0,__SF_EMPTY(%r15) - ni __SF_EMPTY+4(%r15),0xef - lctlg %c0,%c0,__SF_EMPTY(%r15) - /* Set prefix page to zero */ xc __SF_EMPTY(4,%r15),__SF_EMPTY(%r15) spx __SF_EMPTY(%r15) @@ -178,7 +163,7 @@ swsusp_arch_resume: /* Load old stack */ lg %r15,0x2f8(%r13) - /* Pointer to save arae */ + /* Pointer to save area */ lghi %r13,0x1000 #ifdef CONFIG_SMP @@ -190,11 +175,6 @@ swsusp_arch_resume: /* Restore prefix register */ spx 0x318(%r13) - /* Switch on lowcore protection */ - stctg %c0,%c0,__SF_EMPTY(%r15) - oi __SF_EMPTY+4(%r15),0x10 - lctlg %c0,%c0,__SF_EMPTY(%r15) - /* Activate DAT */ stosm __SF_EMPTY(%r15),0x04 -- GitLab From 3a6ba4600d6fb913ddb0dd08843ad75405795883 Mon Sep 17 00:00:00 2001 From: Heiko Carstens Date: Fri, 24 Jul 2009 12:39:51 +0200 Subject: [PATCH 0265/1342] [S390] vdso: fix per cpu area allocation vdso per cpu area allocation in smp_prepare_cpus() happens with GFP_KERNEL but irqs disabled. Triggers this one: Badness at kernel/lockdep.c:2280 Modules linked in: CPU: 0 Not tainted 2.6.30 #2 Process swapper (pid: 1, task: 000000003fe88000, ksp: 000000003fe87eb8) Krnl PSW : 0400c00180000000 0000000000083360 (lockdep_trace_alloc+0xec/0xf8) [...] Call Trace: ([<00000000000832b6>] lockdep_trace_alloc+0x42/0xf8) [<00000000000b1880>] __alloc_pages_internal+0x3e8/0x5c4 [<00000000000b1b4a>] __get_free_pages+0x3a/0xb0 [<0000000000026546>] vdso_alloc_per_cpu+0x6a/0x18c [<00000000005eff82>] smp_prepare_cpus+0x322/0x594 [<00000000005e8232>] kernel_init+0x76/0x398 [<000000000001bb1e>] kernel_thread_starter+0x6/0xc [<000000000001bb18>] kernel_thread_starter+0x0/0xc Fix this by moving the allocation out of the irqs disabled section. Reported-by: Christian Borntraeger Signed-off-by: Heiko Carstens Signed-off-by: Martin Schwidefsky --- arch/s390/kernel/smp.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/arch/s390/kernel/smp.c b/arch/s390/kernel/smp.c index 2270730f535..be2cae08340 100644 --- a/arch/s390/kernel/smp.c +++ b/arch/s390/kernel/smp.c @@ -687,13 +687,14 @@ void __init smp_prepare_cpus(unsigned int max_cpus) #ifndef CONFIG_64BIT if (MACHINE_HAS_IEEE) lowcore->extended_save_area_addr = (u32) save_area; -#else - if (vdso_alloc_per_cpu(smp_processor_id(), lowcore)) - BUG(); #endif set_prefix((u32)(unsigned long) lowcore); local_mcck_enable(); local_irq_enable(); +#ifdef CONFIG_64BIT + if (vdso_alloc_per_cpu(smp_processor_id(), &S390_lowcore)) + BUG(); +#endif for_each_possible_cpu(cpu) if (cpu != smp_processor_id()) smp_create_idle(cpu); -- GitLab From 1277580fe5dfb5aef84854bdb7983657df00b920 Mon Sep 17 00:00:00 2001 From: Martin Schwidefsky Date: Fri, 24 Jul 2009 12:39:52 +0200 Subject: [PATCH 0266/1342] [S390] vdso: clock_gettime of CLOCK_THREAD_CPUTIME_ID with noexec=on The combination of noexec=on and a clock_gettime call with clock id CLOCK_THREAD_CPUTIME_ID is broken. The vdso code switches to the access register mode to get access to the per-cpu data structure to execute the magic ectg instruction. After the ectg instruction the code always switches back to the primary mode but for noexec=on the correct mode is the secondary mode. The effect of the bug is that the user space program looses the access to all mappings without PROT_EXEC, e.g. the stack. The problem is fixed by restoring the mode that has been active before the switch to the access register mode. Signed-off-by: Martin Schwidefsky --- arch/s390/kernel/vdso64/clock_gettime.S | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-) diff --git a/arch/s390/kernel/vdso64/clock_gettime.S b/arch/s390/kernel/vdso64/clock_gettime.S index 79dbfee831e..49106c6e6f8 100644 --- a/arch/s390/kernel/vdso64/clock_gettime.S +++ b/arch/s390/kernel/vdso64/clock_gettime.S @@ -88,10 +88,17 @@ __kernel_clock_gettime: llilh %r4,0x0100 sar %a4,%r4 lghi %r4,0 + epsw %r5,0 sacf 512 /* Magic ectg instruction */ .insn ssf,0xc80100000000,__VDSO_ECTG_BASE(4),__VDSO_ECTG_USER(4),4 - sacf 0 - sar %a4,%r2 + tml %r5,0x4000 + jo 11f + tml %r5,0x8000 + jno 10f + sacf 256 + j 11f +10: sacf 0 +11: sar %a4,%r2 algr %r1,%r0 /* r1 = cputime as TOD value */ mghi %r1,1000 /* convert to nanoseconds */ srlg %r1,%r1,12 /* r1 = cputime in nanosec */ -- GitLab From 8d406c6de2e67b5bae3c43b62b492c4ff63afb92 Mon Sep 17 00:00:00 2001 From: Felix Beck Date: Fri, 24 Jul 2009 12:39:53 +0200 Subject: [PATCH 0267/1342] [S390] zcrypt: fix scheduling of hrtimer ap_poll_timer Every time a request is enqueued or there is some work outstanding from the ap_tasklet, the ap_poll_timer is scheduled again. Unfortunately it was permanently called. It looked as if it was started in the past and thus imediately expired. This has been changed. First it is checked if the hrtimer is already expired. Then the expiring time is forwarded and the timer restarted. Signed-off-by: Felix Beck Signed-off-by: Martin Schwidefsky --- drivers/s390/crypto/ap_bus.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) diff --git a/drivers/s390/crypto/ap_bus.c b/drivers/s390/crypto/ap_bus.c index 727a809636d..ed3dcdea7fe 100644 --- a/drivers/s390/crypto/ap_bus.c +++ b/drivers/s390/crypto/ap_bus.c @@ -1145,12 +1145,17 @@ ap_config_timeout(unsigned long ptr) */ static inline void ap_schedule_poll_timer(void) { + ktime_t hr_time; if (ap_using_interrupts() || ap_suspend_flag) return; if (hrtimer_is_queued(&ap_poll_timer)) return; - hrtimer_start(&ap_poll_timer, ktime_set(0, poll_timeout), - HRTIMER_MODE_ABS); + if (ktime_to_ns(hrtimer_expires_remaining(&ap_poll_timer)) <= 0) { + hr_time = ktime_set(0, poll_timeout); + hrtimer_forward_now(&ap_poll_timer, hr_time); + hrtimer_restart(&ap_poll_timer); + } + return; } /** -- GitLab From 963030817060e4f109be1993b9ae8f81dbf5e11a Mon Sep 17 00:00:00 2001 From: Josef Bacik Date: Mon, 13 Jul 2009 21:29:25 -0400 Subject: [PATCH 0268/1342] Btrfs: use hybrid extents+bitmap rb tree for free space Currently btrfs has a problem where it can use a ridiculous amount of RAM simply tracking free space. As free space gets fragmented, we end up with thousands of entries on an rb-tree per block group, which usually spans 1 gig of area. Since we currently don't ever flush free space cache back to disk this gets to be a bit unweildly on large fs's with lots of fragmentation. This patch solves this problem by using PAGE_SIZE bitmaps for parts of the free space cache. Initially we calculate a threshold of extent entries we can handle, which is however many extent entries we can cram into 16k of ram. The maximum amount of RAM that should ever be used to track 1 gigabyte of diskspace will be 32k of RAM, which scales much better than we did before. Once we pass the extent threshold, we start adding bitmaps and using those instead for tracking the free space. This patch also makes it so that any free space thats less than 4 * sectorsize we go ahead and put into a bitmap. This is nice since we try and allocate out of the front of a block group, so if the front of a block group is heavily fragmented and then has a huge chunk of free space at the end, we go ahead and add the fragmented areas to bitmaps and use a normal extent entry to track the big chunk at the back of the block group. I've also taken the opportunity to revamp how we search for free space. Previously we indexed free space via an offset indexed rb tree and a bytes indexed rb tree. I've dropped the bytes indexed rb tree and use only the offset indexed rb tree. This cuts the number of tree operations we were doing previously down by half, and gives us a little bit of a better allocation pattern since we will always start from a specific offset and search forward from there, instead of searching for the size we need and try and get it as close as possible to the offset we want. I've given this a healthy amount of testing pre-new format stuff, as well as post-new format stuff. I've booted up my fedora box which is installed on btrfs with this patch and ran with it for a few days without issues. I've not seen any performance regressions in any of my tests. Since the last patch Yan Zheng fixed a problem where we could have overlapping entries, so updating their offset inline would cause problems. Thanks, Signed-off-by: Josef Bacik Signed-off-by: Chris Mason --- fs/btrfs/ctree.h | 8 +- fs/btrfs/extent-tree.c | 25 +- fs/btrfs/free-space-cache.c | 1001 +++++++++++++++++++++++++++-------- fs/btrfs/free-space-cache.h | 8 + 4 files changed, 826 insertions(+), 216 deletions(-) diff --git a/fs/btrfs/ctree.h b/fs/btrfs/ctree.h index da0763135bf..0cbf3491bb7 100644 --- a/fs/btrfs/ctree.h +++ b/fs/btrfs/ctree.h @@ -709,6 +709,9 @@ struct btrfs_free_cluster { /* first extent starting offset */ u64 window_start; + /* if this cluster simply points at a bitmap in the block group */ + bool points_to_bitmap; + struct btrfs_block_group_cache *block_group; /* * when a cluster is allocated from a block group, we put the @@ -726,6 +729,10 @@ struct btrfs_block_group_cache { u64 pinned; u64 reserved; u64 flags; + u64 sectorsize; + int extents_thresh; + int free_extents; + int total_bitmaps; int cached; int ro; int dirty; @@ -734,7 +741,6 @@ struct btrfs_block_group_cache { /* free space cache stuff */ spinlock_t tree_lock; - struct rb_root free_space_bytes; struct rb_root free_space_offset; /* block group cache stuff */ diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c index 62a332d34fd..98697be6bdd 100644 --- a/fs/btrfs/extent-tree.c +++ b/fs/btrfs/extent-tree.c @@ -3649,7 +3649,6 @@ refill_cluster: goto loop; checks: search_start = stripe_align(root, offset); - /* move on to the next group */ if (search_start + num_bytes >= search_end) { btrfs_add_free_space(block_group, offset, num_bytes); @@ -7040,6 +7039,16 @@ int btrfs_read_block_groups(struct btrfs_root *root) mutex_init(&cache->cache_mutex); INIT_LIST_HEAD(&cache->list); INIT_LIST_HEAD(&cache->cluster_list); + cache->sectorsize = root->sectorsize; + + /* + * we only want to have 32k of ram per block group for keeping + * track of free space, and if we pass 1/2 of that we want to + * start converting things over to using bitmaps + */ + cache->extents_thresh = ((1024 * 32) / 2) / + sizeof(struct btrfs_free_space); + read_extent_buffer(leaf, &cache->item, btrfs_item_ptr_offset(leaf, path->slots[0]), sizeof(cache->item)); @@ -7091,6 +7100,15 @@ int btrfs_make_block_group(struct btrfs_trans_handle *trans, cache->key.objectid = chunk_offset; cache->key.offset = size; cache->key.type = BTRFS_BLOCK_GROUP_ITEM_KEY; + cache->sectorsize = root->sectorsize; + + /* + * we only want to have 32k of ram per block group for keeping track + * of free space, and if we pass 1/2 of that we want to start + * converting things over to using bitmaps + */ + cache->extents_thresh = ((1024 * 32) / 2) / + sizeof(struct btrfs_free_space); atomic_set(&cache->count, 1); spin_lock_init(&cache->lock); spin_lock_init(&cache->tree_lock); @@ -7103,6 +7121,11 @@ int btrfs_make_block_group(struct btrfs_trans_handle *trans, cache->flags = type; btrfs_set_block_group_flags(&cache->item, type); + cache->cached = 1; + ret = btrfs_add_free_space(cache, chunk_offset, size); + BUG_ON(ret); + remove_sb_from_cache(root, cache); + ret = update_space_info(root->fs_info, cache->flags, size, bytes_used, &cache->space_info); BUG_ON(ret); diff --git a/fs/btrfs/free-space-cache.c b/fs/btrfs/free-space-cache.c index 4538e48581a..ab8cad8b46c 100644 --- a/fs/btrfs/free-space-cache.c +++ b/fs/btrfs/free-space-cache.c @@ -16,45 +16,46 @@ * Boston, MA 021110-1307, USA. */ +#include #include +#include #include "ctree.h" #include "free-space-cache.h" #include "transaction.h" -struct btrfs_free_space { - struct rb_node bytes_index; - struct rb_node offset_index; - u64 offset; - u64 bytes; -}; +#define BITS_PER_BITMAP (PAGE_CACHE_SIZE * 8) +#define MAX_CACHE_BYTES_PER_GIG (32 * 1024) -static int tree_insert_offset(struct rb_root *root, u64 offset, - struct rb_node *node) +static inline unsigned long offset_to_bit(u64 bitmap_start, u64 sectorsize, + u64 offset) { - struct rb_node **p = &root->rb_node; - struct rb_node *parent = NULL; - struct btrfs_free_space *info; + BUG_ON(offset < bitmap_start); + offset -= bitmap_start; + return (unsigned long)(div64_u64(offset, sectorsize)); +} - while (*p) { - parent = *p; - info = rb_entry(parent, struct btrfs_free_space, offset_index); +static inline unsigned long bytes_to_bits(u64 bytes, u64 sectorsize) +{ + return (unsigned long)(div64_u64(bytes, sectorsize)); +} - if (offset < info->offset) - p = &(*p)->rb_left; - else if (offset > info->offset) - p = &(*p)->rb_right; - else - return -EEXIST; - } +static inline u64 offset_to_bitmap(struct btrfs_block_group_cache *block_group, + u64 offset) +{ + u64 bitmap_start; + u64 bytes_per_bitmap; - rb_link_node(node, parent, p); - rb_insert_color(node, root); + bytes_per_bitmap = BITS_PER_BITMAP * block_group->sectorsize; + bitmap_start = offset - block_group->key.objectid; + bitmap_start = div64_u64(bitmap_start, bytes_per_bitmap); + bitmap_start *= bytes_per_bitmap; + bitmap_start += block_group->key.objectid; - return 0; + return bitmap_start; } -static int tree_insert_bytes(struct rb_root *root, u64 bytes, - struct rb_node *node) +static int tree_insert_offset(struct rb_root *root, u64 offset, + struct rb_node *node, int bitmap) { struct rb_node **p = &root->rb_node; struct rb_node *parent = NULL; @@ -62,12 +63,34 @@ static int tree_insert_bytes(struct rb_root *root, u64 bytes, while (*p) { parent = *p; - info = rb_entry(parent, struct btrfs_free_space, bytes_index); + info = rb_entry(parent, struct btrfs_free_space, offset_index); - if (bytes < info->bytes) + if (offset < info->offset) { p = &(*p)->rb_left; - else + } else if (offset > info->offset) { p = &(*p)->rb_right; + } else { + /* + * we could have a bitmap entry and an extent entry + * share the same offset. If this is the case, we want + * the extent entry to always be found first if we do a + * linear search through the tree, since we want to have + * the quickest allocation time, and allocating from an + * extent is faster than allocating from a bitmap. So + * if we're inserting a bitmap and we find an entry at + * this offset, we want to go right, or after this entry + * logically. If we are inserting an extent and we've + * found a bitmap, we want to go left, or before + * logically. + */ + if (bitmap) { + WARN_ON(info->bitmap); + p = &(*p)->rb_right; + } else { + WARN_ON(!info->bitmap); + p = &(*p)->rb_left; + } + } } rb_link_node(node, parent, p); @@ -79,110 +102,142 @@ static int tree_insert_bytes(struct rb_root *root, u64 bytes, /* * searches the tree for the given offset. * - * fuzzy == 1: this is used for allocations where we are given a hint of where - * to look for free space. Because the hint may not be completely on an offset - * mark, or the hint may no longer point to free space we need to fudge our - * results a bit. So we look for free space starting at or after offset with at - * least bytes size. We prefer to find as close to the given offset as we can. - * Also if the offset is within a free space range, then we will return the free - * space that contains the given offset, which means we can return a free space - * chunk with an offset before the provided offset. - * - * fuzzy == 0: this is just a normal tree search. Give us the free space that - * starts at the given offset which is at least bytes size, and if its not there - * return NULL. + * fuzzy - If this is set, then we are trying to make an allocation, and we just + * want a section that has at least bytes size and comes at or after the given + * offset. */ -static struct btrfs_free_space *tree_search_offset(struct rb_root *root, - u64 offset, u64 bytes, - int fuzzy) +static struct btrfs_free_space * +tree_search_offset(struct btrfs_block_group_cache *block_group, + u64 offset, int bitmap_only, int fuzzy) { - struct rb_node *n = root->rb_node; - struct btrfs_free_space *entry, *ret = NULL; + struct rb_node *n = block_group->free_space_offset.rb_node; + struct btrfs_free_space *entry, *prev = NULL; + + /* find entry that is closest to the 'offset' */ + while (1) { + if (!n) { + entry = NULL; + break; + } - while (n) { entry = rb_entry(n, struct btrfs_free_space, offset_index); + prev = entry; - if (offset < entry->offset) { - if (fuzzy && - (!ret || entry->offset < ret->offset) && - (bytes <= entry->bytes)) - ret = entry; + if (offset < entry->offset) n = n->rb_left; - } else if (offset > entry->offset) { - if (fuzzy && - (entry->offset + entry->bytes - 1) >= offset && - bytes <= entry->bytes) { - ret = entry; - break; - } + else if (offset > entry->offset) n = n->rb_right; - } else { - if (bytes > entry->bytes) { - n = n->rb_right; - continue; - } - ret = entry; + else break; - } } - return ret; -} - -/* - * return a chunk at least bytes size, as close to offset that we can get. - */ -static struct btrfs_free_space *tree_search_bytes(struct rb_root *root, - u64 offset, u64 bytes) -{ - struct rb_node *n = root->rb_node; - struct btrfs_free_space *entry, *ret = NULL; + if (bitmap_only) { + if (!entry) + return NULL; + if (entry->bitmap) + return entry; - while (n) { - entry = rb_entry(n, struct btrfs_free_space, bytes_index); + /* + * bitmap entry and extent entry may share same offset, + * in that case, bitmap entry comes after extent entry. + */ + n = rb_next(n); + if (!n) + return NULL; + entry = rb_entry(n, struct btrfs_free_space, offset_index); + if (entry->offset != offset) + return NULL; - if (bytes < entry->bytes) { + WARN_ON(!entry->bitmap); + return entry; + } else if (entry) { + if (entry->bitmap) { /* - * We prefer to get a hole size as close to the size we - * are asking for so we don't take small slivers out of - * huge holes, but we also want to get as close to the - * offset as possible so we don't have a whole lot of - * fragmentation. + * if previous extent entry covers the offset, + * we should return it instead of the bitmap entry */ - if (offset <= entry->offset) { - if (!ret) - ret = entry; - else if (entry->bytes < ret->bytes) - ret = entry; - else if (entry->offset < ret->offset) - ret = entry; + n = &entry->offset_index; + while (1) { + n = rb_prev(n); + if (!n) + break; + prev = rb_entry(n, struct btrfs_free_space, + offset_index); + if (!prev->bitmap) { + if (prev->offset + prev->bytes > offset) + entry = prev; + break; + } } - n = n->rb_left; - } else if (bytes > entry->bytes) { - n = n->rb_right; + } + return entry; + } + + if (!prev) + return NULL; + + /* find last entry before the 'offset' */ + entry = prev; + if (entry->offset > offset) { + n = rb_prev(&entry->offset_index); + if (n) { + entry = rb_entry(n, struct btrfs_free_space, + offset_index); + BUG_ON(entry->offset > offset); } else { - /* - * Ok we may have multiple chunks of the wanted size, - * so we don't want to take the first one we find, we - * want to take the one closest to our given offset, so - * keep searching just in case theres a better match. - */ - n = n->rb_right; - if (offset > entry->offset) - continue; - else if (!ret || entry->offset < ret->offset) - ret = entry; + if (fuzzy) + return entry; + else + return NULL; } } - return ret; + if (entry->bitmap) { + n = &entry->offset_index; + while (1) { + n = rb_prev(n); + if (!n) + break; + prev = rb_entry(n, struct btrfs_free_space, + offset_index); + if (!prev->bitmap) { + if (prev->offset + prev->bytes > offset) + return prev; + break; + } + } + if (entry->offset + BITS_PER_BITMAP * + block_group->sectorsize > offset) + return entry; + } else if (entry->offset + entry->bytes > offset) + return entry; + + if (!fuzzy) + return NULL; + + while (1) { + if (entry->bitmap) { + if (entry->offset + BITS_PER_BITMAP * + block_group->sectorsize > offset) + break; + } else { + if (entry->offset + entry->bytes > offset) + break; + } + + n = rb_next(&entry->offset_index); + if (!n) + return NULL; + entry = rb_entry(n, struct btrfs_free_space, offset_index); + } + return entry; } static void unlink_free_space(struct btrfs_block_group_cache *block_group, struct btrfs_free_space *info) { rb_erase(&info->offset_index, &block_group->free_space_offset); - rb_erase(&info->bytes_index, &block_group->free_space_bytes); + block_group->free_extents--; } static int link_free_space(struct btrfs_block_group_cache *block_group, @@ -190,17 +245,311 @@ static int link_free_space(struct btrfs_block_group_cache *block_group, { int ret = 0; - - BUG_ON(!info->bytes); + BUG_ON(!info->bitmap && !info->bytes); ret = tree_insert_offset(&block_group->free_space_offset, info->offset, - &info->offset_index); + &info->offset_index, (info->bitmap != NULL)); if (ret) return ret; - ret = tree_insert_bytes(&block_group->free_space_bytes, info->bytes, - &info->bytes_index); - if (ret) - return ret; + block_group->free_extents++; + return ret; +} + +static void recalculate_thresholds(struct btrfs_block_group_cache *block_group) +{ + u64 max_bytes, possible_bytes; + + /* + * The goal is to keep the total amount of memory used per 1gb of space + * at or below 32k, so we need to adjust how much memory we allow to be + * used by extent based free space tracking + */ + max_bytes = MAX_CACHE_BYTES_PER_GIG * + (div64_u64(block_group->key.offset, 1024 * 1024 * 1024)); + + possible_bytes = (block_group->total_bitmaps * PAGE_CACHE_SIZE) + + (sizeof(struct btrfs_free_space) * + block_group->extents_thresh); + + if (possible_bytes > max_bytes) { + int extent_bytes = max_bytes - + (block_group->total_bitmaps * PAGE_CACHE_SIZE); + + if (extent_bytes <= 0) { + block_group->extents_thresh = 0; + return; + } + + block_group->extents_thresh = extent_bytes / + (sizeof(struct btrfs_free_space)); + } +} + +static void bitmap_clear_bits(struct btrfs_free_space *info, u64 offset, u64 bytes, + u64 sectorsize) +{ + unsigned long start, end; + unsigned long i; + + start = offset_to_bit(info->offset, sectorsize, offset); + end = start + bytes_to_bits(bytes, sectorsize); + BUG_ON(end > BITS_PER_BITMAP); + + for (i = start; i < end; i++) + clear_bit(i, info->bitmap); + + info->bytes -= bytes; +} + +static void bitmap_set_bits(struct btrfs_free_space *info, u64 offset, u64 bytes, + u64 sectorsize) +{ + unsigned long start, end; + unsigned long i; + + start = offset_to_bit(info->offset, sectorsize, offset); + end = start + bytes_to_bits(bytes, sectorsize); + BUG_ON(end > BITS_PER_BITMAP); + + for (i = start; i < end; i++) + set_bit(i, info->bitmap); + + info->bytes += bytes; +} + +static int search_bitmap(struct btrfs_block_group_cache *block_group, + struct btrfs_free_space *bitmap_info, u64 *offset, + u64 *bytes) +{ + unsigned long found_bits = 0; + unsigned long bits, i; + unsigned long next_zero; + + i = offset_to_bit(bitmap_info->offset, block_group->sectorsize, + max_t(u64, *offset, bitmap_info->offset)); + bits = bytes_to_bits(*bytes, block_group->sectorsize); + + for (i = find_next_bit(bitmap_info->bitmap, BITS_PER_BITMAP, i); + i < BITS_PER_BITMAP; + i = find_next_bit(bitmap_info->bitmap, BITS_PER_BITMAP, i + 1)) { + next_zero = find_next_zero_bit(bitmap_info->bitmap, + BITS_PER_BITMAP, i); + if ((next_zero - i) >= bits) { + found_bits = next_zero - i; + break; + } + i = next_zero; + } + + if (found_bits) { + *offset = (u64)(i * block_group->sectorsize) + + bitmap_info->offset; + *bytes = (u64)(found_bits) * block_group->sectorsize; + return 0; + } + + return -1; +} + +static struct btrfs_free_space *find_free_space(struct btrfs_block_group_cache + *block_group, u64 *offset, + u64 *bytes, int debug) +{ + struct btrfs_free_space *entry; + struct rb_node *node; + int ret; + + if (!block_group->free_space_offset.rb_node) + return NULL; + + entry = tree_search_offset(block_group, + offset_to_bitmap(block_group, *offset), + 0, 1); + if (!entry) + return NULL; + + for (node = &entry->offset_index; node; node = rb_next(node)) { + entry = rb_entry(node, struct btrfs_free_space, offset_index); + if (entry->bytes < *bytes) + continue; + + if (entry->bitmap) { + ret = search_bitmap(block_group, entry, offset, bytes); + if (!ret) + return entry; + continue; + } + + *offset = entry->offset; + *bytes = entry->bytes; + return entry; + } + + return NULL; +} + +static void add_new_bitmap(struct btrfs_block_group_cache *block_group, + struct btrfs_free_space *info, u64 offset) +{ + u64 bytes_per_bg = BITS_PER_BITMAP * block_group->sectorsize; + int max_bitmaps = (int)div64_u64(block_group->key.offset + + bytes_per_bg - 1, bytes_per_bg); + BUG_ON(block_group->total_bitmaps >= max_bitmaps); + + info->offset = offset_to_bitmap(block_group, offset); + link_free_space(block_group, info); + block_group->total_bitmaps++; + + recalculate_thresholds(block_group); +} + +static noinline int remove_from_bitmap(struct btrfs_block_group_cache *block_group, + struct btrfs_free_space *bitmap_info, + u64 *offset, u64 *bytes) +{ + u64 end; + +again: + end = bitmap_info->offset + + (u64)(BITS_PER_BITMAP * block_group->sectorsize) - 1; + + if (*offset > bitmap_info->offset && *offset + *bytes > end) { + bitmap_clear_bits(bitmap_info, *offset, + end - *offset + 1, block_group->sectorsize); + *bytes -= end - *offset + 1; + *offset = end + 1; + } else if (*offset >= bitmap_info->offset && *offset + *bytes <= end) { + bitmap_clear_bits(bitmap_info, *offset, + *bytes, block_group->sectorsize); + *bytes = 0; + } + + if (*bytes) { + if (!bitmap_info->bytes) { + unlink_free_space(block_group, bitmap_info); + kfree(bitmap_info->bitmap); + kfree(bitmap_info); + block_group->total_bitmaps--; + recalculate_thresholds(block_group); + } + + bitmap_info = tree_search_offset(block_group, + offset_to_bitmap(block_group, + *offset), + 1, 0); + if (!bitmap_info) + return -EINVAL; + + if (!bitmap_info->bitmap) + return -EAGAIN; + + goto again; + } else if (!bitmap_info->bytes) { + unlink_free_space(block_group, bitmap_info); + kfree(bitmap_info->bitmap); + kfree(bitmap_info); + block_group->total_bitmaps--; + recalculate_thresholds(block_group); + } + + return 0; +} + +static int insert_into_bitmap(struct btrfs_block_group_cache *block_group, + struct btrfs_free_space *info) +{ + struct btrfs_free_space *bitmap_info; + int added = 0; + u64 bytes, offset, end; + int ret; + + /* + * If we are below the extents threshold then we can add this as an + * extent, and don't have to deal with the bitmap + */ + if (block_group->free_extents < block_group->extents_thresh && + info->bytes > block_group->sectorsize * 4) + return 0; + + /* + * some block groups are so tiny they can't be enveloped by a bitmap, so + * don't even bother to create a bitmap for this + */ + if (BITS_PER_BITMAP * block_group->sectorsize > + block_group->key.offset) + return 0; + + bytes = info->bytes; + offset = info->offset; + +again: + bitmap_info = tree_search_offset(block_group, + offset_to_bitmap(block_group, offset), + 1, 0); + if (!bitmap_info) { + BUG_ON(added); + goto new_bitmap; + } + + end = bitmap_info->offset + + (u64)(BITS_PER_BITMAP * block_group->sectorsize); + + if (offset >= bitmap_info->offset && offset + bytes > end) { + bitmap_set_bits(bitmap_info, offset, end - offset, + block_group->sectorsize); + bytes -= end - offset; + offset = end; + added = 0; + } else if (offset >= bitmap_info->offset && offset + bytes <= end) { + bitmap_set_bits(bitmap_info, offset, bytes, + block_group->sectorsize); + bytes = 0; + } else { + BUG(); + } + + if (!bytes) { + ret = 1; + goto out; + } else + goto again; + +new_bitmap: + if (info && info->bitmap) { + add_new_bitmap(block_group, info, offset); + added = 1; + info = NULL; + goto again; + } else { + spin_unlock(&block_group->tree_lock); + + /* no pre-allocated info, allocate a new one */ + if (!info) { + info = kzalloc(sizeof(struct btrfs_free_space), + GFP_NOFS); + if (!info) { + spin_lock(&block_group->tree_lock); + ret = -ENOMEM; + goto out; + } + } + + /* allocate the bitmap */ + info->bitmap = kzalloc(PAGE_CACHE_SIZE, GFP_NOFS); + spin_lock(&block_group->tree_lock); + if (!info->bitmap) { + ret = -ENOMEM; + goto out; + } + goto again; + } + +out: + if (info) { + if (info->bitmap) + kfree(info->bitmap); + kfree(info); + } return ret; } @@ -208,8 +557,8 @@ static int link_free_space(struct btrfs_block_group_cache *block_group, int btrfs_add_free_space(struct btrfs_block_group_cache *block_group, u64 offset, u64 bytes) { - struct btrfs_free_space *right_info; - struct btrfs_free_space *left_info; + struct btrfs_free_space *right_info = NULL; + struct btrfs_free_space *left_info = NULL; struct btrfs_free_space *info = NULL; int ret = 0; @@ -227,18 +576,38 @@ int btrfs_add_free_space(struct btrfs_block_group_cache *block_group, * are adding, if there is remove that struct and add a new one to * cover the entire range */ - right_info = tree_search_offset(&block_group->free_space_offset, - offset+bytes, 0, 0); - left_info = tree_search_offset(&block_group->free_space_offset, - offset-1, 0, 1); + right_info = tree_search_offset(block_group, offset + bytes, 0, 0); + if (right_info && rb_prev(&right_info->offset_index)) + left_info = rb_entry(rb_prev(&right_info->offset_index), + struct btrfs_free_space, offset_index); + else + left_info = tree_search_offset(block_group, offset - 1, 0, 0); - if (right_info) { + /* + * If there was no extent directly to the left or right of this new + * extent then we know we're going to have to allocate a new extent, so + * before we do that see if we need to drop this into a bitmap + */ + if ((!left_info || left_info->bitmap) && + (!right_info || right_info->bitmap)) { + ret = insert_into_bitmap(block_group, info); + + if (ret < 0) { + goto out; + } else if (ret) { + ret = 0; + goto out; + } + } + + if (right_info && !right_info->bitmap) { unlink_free_space(block_group, right_info); info->bytes += right_info->bytes; kfree(right_info); } - if (left_info && left_info->offset + left_info->bytes == offset) { + if (left_info && !left_info->bitmap && + left_info->offset + left_info->bytes == offset) { unlink_free_space(block_group, left_info); info->offset = left_info->offset; info->bytes += left_info->bytes; @@ -248,11 +617,11 @@ int btrfs_add_free_space(struct btrfs_block_group_cache *block_group, ret = link_free_space(block_group, info); if (ret) kfree(info); - +out: spin_unlock(&block_group->tree_lock); if (ret) { - printk(KERN_ERR "btrfs: unable to add free space :%d\n", ret); + printk(KERN_CRIT "btrfs: unable to add free space :%d\n", ret); BUG_ON(ret == -EEXIST); } @@ -263,40 +632,65 @@ int btrfs_remove_free_space(struct btrfs_block_group_cache *block_group, u64 offset, u64 bytes) { struct btrfs_free_space *info; + struct btrfs_free_space *next_info = NULL; int ret = 0; spin_lock(&block_group->tree_lock); - info = tree_search_offset(&block_group->free_space_offset, offset, 0, - 1); - if (info && info->offset == offset) { - if (info->bytes < bytes) { - printk(KERN_ERR "Found free space at %llu, size %llu," - "trying to use %llu\n", - (unsigned long long)info->offset, - (unsigned long long)info->bytes, - (unsigned long long)bytes); +again: + info = tree_search_offset(block_group, offset, 0, 0); + if (!info) { + WARN_ON(1); + goto out_lock; + } + + if (info->bytes < bytes && rb_next(&info->offset_index)) { + u64 end; + next_info = rb_entry(rb_next(&info->offset_index), + struct btrfs_free_space, + offset_index); + + if (next_info->bitmap) + end = next_info->offset + BITS_PER_BITMAP * + block_group->sectorsize - 1; + else + end = next_info->offset + next_info->bytes; + + if (next_info->bytes < bytes || + next_info->offset > offset || offset > end) { + printk(KERN_CRIT "Found free space at %llu, size %llu," + " trying to use %llu\n", + (unsigned long long)info->offset, + (unsigned long long)info->bytes, + (unsigned long long)bytes); WARN_ON(1); ret = -EINVAL; - spin_unlock(&block_group->tree_lock); - goto out; + goto out_lock; } - unlink_free_space(block_group, info); - if (info->bytes == bytes) { - kfree(info); - spin_unlock(&block_group->tree_lock); - goto out; + info = next_info; + } + + if (info->bytes == bytes) { + unlink_free_space(block_group, info); + if (info->bitmap) { + kfree(info->bitmap); + block_group->total_bitmaps--; } + kfree(info); + goto out_lock; + } + if (!info->bitmap && info->offset == offset) { + unlink_free_space(block_group, info); info->offset += bytes; info->bytes -= bytes; + link_free_space(block_group, info); + goto out_lock; + } - ret = link_free_space(block_group, info); - spin_unlock(&block_group->tree_lock); - BUG_ON(ret); - } else if (info && info->offset < offset && - info->offset + info->bytes >= offset + bytes) { + if (!info->bitmap && info->offset <= offset && + info->offset + info->bytes >= offset + bytes) { u64 old_start = info->offset; /* * we're freeing space in the middle of the info, @@ -312,7 +706,9 @@ int btrfs_remove_free_space(struct btrfs_block_group_cache *block_group, info->offset = offset + bytes; info->bytes = old_end - info->offset; ret = link_free_space(block_group, info); - BUG_ON(ret); + WARN_ON(ret); + if (ret) + goto out_lock; } else { /* the hole we're creating ends at the end * of the info struct, just free the info @@ -320,32 +716,22 @@ int btrfs_remove_free_space(struct btrfs_block_group_cache *block_group, kfree(info); } spin_unlock(&block_group->tree_lock); - /* step two, insert a new info struct to cover anything - * before the hole + + /* step two, insert a new info struct to cover + * anything before the hole */ ret = btrfs_add_free_space(block_group, old_start, offset - old_start); - BUG_ON(ret); - } else { - spin_unlock(&block_group->tree_lock); - if (!info) { - printk(KERN_ERR "couldn't find space %llu to free\n", - (unsigned long long)offset); - printk(KERN_ERR "cached is %d, offset %llu bytes %llu\n", - block_group->cached, - (unsigned long long)block_group->key.objectid, - (unsigned long long)block_group->key.offset); - btrfs_dump_free_space(block_group, bytes); - } else if (info) { - printk(KERN_ERR "hmm, found offset=%llu bytes=%llu, " - "but wanted offset=%llu bytes=%llu\n", - (unsigned long long)info->offset, - (unsigned long long)info->bytes, - (unsigned long long)offset, - (unsigned long long)bytes); - } - WARN_ON(1); + WARN_ON(ret); + goto out; } + + ret = remove_from_bitmap(block_group, info, &offset, &bytes); + if (ret == -EAGAIN) + goto again; + BUG_ON(ret); +out_lock: + spin_unlock(&block_group->tree_lock); out: return ret; } @@ -361,10 +747,13 @@ void btrfs_dump_free_space(struct btrfs_block_group_cache *block_group, info = rb_entry(n, struct btrfs_free_space, offset_index); if (info->bytes >= bytes) count++; - printk(KERN_ERR "entry offset %llu, bytes %llu\n", + printk(KERN_CRIT "entry offset %llu, bytes %llu, bitmap %s\n", (unsigned long long)info->offset, - (unsigned long long)info->bytes); + (unsigned long long)info->bytes, + (info->bitmap) ? "yes" : "no"); } + printk(KERN_INFO "block group has cluster?: %s\n", + list_empty(&block_group->cluster_list) ? "no" : "yes"); printk(KERN_INFO "%d blocks of free space at or bigger than bytes is" "\n", count); } @@ -397,26 +786,35 @@ __btrfs_return_cluster_to_free_space( { struct btrfs_free_space *entry; struct rb_node *node; + bool bitmap; spin_lock(&cluster->lock); if (cluster->block_group != block_group) goto out; + bitmap = cluster->points_to_bitmap; + cluster->block_group = NULL; cluster->window_start = 0; + list_del_init(&cluster->block_group_list); + cluster->points_to_bitmap = false; + + if (bitmap) + goto out; + node = rb_first(&cluster->root); - while(node) { + while (node) { entry = rb_entry(node, struct btrfs_free_space, offset_index); node = rb_next(&entry->offset_index); rb_erase(&entry->offset_index, &cluster->root); - link_free_space(block_group, entry); + BUG_ON(entry->bitmap); + tree_insert_offset(&block_group->free_space_offset, + entry->offset, &entry->offset_index, 0); } - list_del_init(&cluster->block_group_list); - - btrfs_put_block_group(cluster->block_group); - cluster->block_group = NULL; cluster->root.rb_node = NULL; + out: spin_unlock(&cluster->lock); + btrfs_put_block_group(block_group); return 0; } @@ -425,20 +823,28 @@ void btrfs_remove_free_space_cache(struct btrfs_block_group_cache *block_group) struct btrfs_free_space *info; struct rb_node *node; struct btrfs_free_cluster *cluster; - struct btrfs_free_cluster *safe; + struct list_head *head; spin_lock(&block_group->tree_lock); - - list_for_each_entry_safe(cluster, safe, &block_group->cluster_list, - block_group_list) { + while ((head = block_group->cluster_list.next) != + &block_group->cluster_list) { + cluster = list_entry(head, struct btrfs_free_cluster, + block_group_list); WARN_ON(cluster->block_group != block_group); __btrfs_return_cluster_to_free_space(block_group, cluster); + if (need_resched()) { + spin_unlock(&block_group->tree_lock); + cond_resched(); + spin_lock(&block_group->tree_lock); + } } - while ((node = rb_last(&block_group->free_space_bytes)) != NULL) { - info = rb_entry(node, struct btrfs_free_space, bytes_index); + while ((node = rb_last(&block_group->free_space_offset)) != NULL) { + info = rb_entry(node, struct btrfs_free_space, offset_index); unlink_free_space(block_group, info); + if (info->bitmap) + kfree(info->bitmap); kfree(info); if (need_resched()) { spin_unlock(&block_group->tree_lock); @@ -446,6 +852,7 @@ void btrfs_remove_free_space_cache(struct btrfs_block_group_cache *block_group) spin_lock(&block_group->tree_lock); } } + spin_unlock(&block_group->tree_lock); } @@ -453,27 +860,37 @@ u64 btrfs_find_space_for_alloc(struct btrfs_block_group_cache *block_group, u64 offset, u64 bytes, u64 empty_size) { struct btrfs_free_space *entry = NULL; + u64 bytes_search = bytes + empty_size; u64 ret = 0; spin_lock(&block_group->tree_lock); - entry = tree_search_offset(&block_group->free_space_offset, offset, - bytes + empty_size, 1); + entry = find_free_space(block_group, &offset, &bytes_search, 0); if (!entry) - entry = tree_search_bytes(&block_group->free_space_bytes, - offset, bytes + empty_size); - if (entry) { + goto out; + + ret = offset; + if (entry->bitmap) { + bitmap_clear_bits(entry, offset, bytes, + block_group->sectorsize); + if (!entry->bytes) { + unlink_free_space(block_group, entry); + kfree(entry->bitmap); + kfree(entry); + block_group->total_bitmaps--; + recalculate_thresholds(block_group); + } + } else { unlink_free_space(block_group, entry); - ret = entry->offset; entry->offset += bytes; entry->bytes -= bytes; - if (!entry->bytes) kfree(entry); else link_free_space(block_group, entry); } - spin_unlock(&block_group->tree_lock); +out: + spin_unlock(&block_group->tree_lock); return ret; } @@ -517,6 +934,47 @@ int btrfs_return_cluster_to_free_space( return ret; } +static u64 btrfs_alloc_from_bitmap(struct btrfs_block_group_cache *block_group, + struct btrfs_free_cluster *cluster, + u64 bytes, u64 min_start) +{ + struct btrfs_free_space *entry; + int err; + u64 search_start = cluster->window_start; + u64 search_bytes = bytes; + u64 ret = 0; + + spin_lock(&block_group->tree_lock); + spin_lock(&cluster->lock); + + if (!cluster->points_to_bitmap) + goto out; + + if (cluster->block_group != block_group) + goto out; + + entry = tree_search_offset(block_group, search_start, 0, 0); + + if (!entry || !entry->bitmap) + goto out; + + search_start = min_start; + search_bytes = bytes; + + err = search_bitmap(block_group, entry, &search_start, + &search_bytes); + if (err) + goto out; + + ret = search_start; + bitmap_clear_bits(entry, ret, bytes, block_group->sectorsize); +out: + spin_unlock(&cluster->lock); + spin_unlock(&block_group->tree_lock); + + return ret; +} + /* * given a cluster, try to allocate 'bytes' from it, returns 0 * if it couldn't find anything suitably large, or a logical disk offset @@ -530,6 +988,10 @@ u64 btrfs_alloc_from_cluster(struct btrfs_block_group_cache *block_group, struct rb_node *node; u64 ret = 0; + if (cluster->points_to_bitmap) + return btrfs_alloc_from_bitmap(block_group, cluster, bytes, + min_start); + spin_lock(&cluster->lock); if (bytes > cluster->max_size) goto out; @@ -567,9 +1029,73 @@ u64 btrfs_alloc_from_cluster(struct btrfs_block_group_cache *block_group, } out: spin_unlock(&cluster->lock); + return ret; } +static int btrfs_bitmap_cluster(struct btrfs_block_group_cache *block_group, + struct btrfs_free_space *entry, + struct btrfs_free_cluster *cluster, + u64 offset, u64 bytes, u64 min_bytes) +{ + unsigned long next_zero; + unsigned long i; + unsigned long search_bits; + unsigned long total_bits; + unsigned long found_bits; + unsigned long start = 0; + unsigned long total_found = 0; + bool found = false; + + i = offset_to_bit(entry->offset, block_group->sectorsize, + max_t(u64, offset, entry->offset)); + search_bits = bytes_to_bits(min_bytes, block_group->sectorsize); + total_bits = bytes_to_bits(bytes, block_group->sectorsize); + +again: + found_bits = 0; + for (i = find_next_bit(entry->bitmap, BITS_PER_BITMAP, i); + i < BITS_PER_BITMAP; + i = find_next_bit(entry->bitmap, BITS_PER_BITMAP, i + 1)) { + next_zero = find_next_zero_bit(entry->bitmap, + BITS_PER_BITMAP, i); + if (next_zero - i >= search_bits) { + found_bits = next_zero - i; + break; + } + i = next_zero; + } + + if (!found_bits) + return -1; + + if (!found) { + start = i; + found = true; + } + + total_found += found_bits; + + if (cluster->max_size < found_bits * block_group->sectorsize) + cluster->max_size = found_bits * block_group->sectorsize; + + if (total_found < total_bits) { + i = find_next_bit(entry->bitmap, BITS_PER_BITMAP, next_zero); + if (i - start > total_bits * 2) { + total_found = 0; + cluster->max_size = 0; + found = false; + } + goto again; + } + + cluster->window_start = start * block_group->sectorsize + + entry->offset; + cluster->points_to_bitmap = true; + + return 0; +} + /* * here we try to find a cluster of blocks in a block group. The goal * is to find at least bytes free and up to empty_size + bytes free. @@ -587,12 +1113,12 @@ int btrfs_find_space_cluster(struct btrfs_trans_handle *trans, struct btrfs_free_space *entry = NULL; struct rb_node *node; struct btrfs_free_space *next; - struct btrfs_free_space *last; + struct btrfs_free_space *last = NULL; u64 min_bytes; u64 window_start; u64 window_free; u64 max_extent = 0; - int total_retries = 0; + bool found_bitmap = false; int ret; /* for metadata, allow allocates with more holes */ @@ -620,30 +1146,79 @@ int btrfs_find_space_cluster(struct btrfs_trans_handle *trans, goto out; } again: - min_bytes = min(min_bytes, bytes + empty_size); - entry = tree_search_bytes(&block_group->free_space_bytes, - offset, min_bytes); + entry = tree_search_offset(block_group, offset, found_bitmap, 1); if (!entry) { ret = -ENOSPC; goto out; } + + /* + * If found_bitmap is true, we exhausted our search for extent entries, + * and we just want to search all of the bitmaps that we can find, and + * ignore any extent entries we find. + */ + while (entry->bitmap || found_bitmap || + (!entry->bitmap && entry->bytes < min_bytes)) { + struct rb_node *node = rb_next(&entry->offset_index); + + if (entry->bitmap && entry->bytes > bytes + empty_size) { + ret = btrfs_bitmap_cluster(block_group, entry, cluster, + offset, bytes + empty_size, + min_bytes); + if (!ret) + goto got_it; + } + + if (!node) { + ret = -ENOSPC; + goto out; + } + entry = rb_entry(node, struct btrfs_free_space, offset_index); + } + + /* + * We already searched all the extent entries from the passed in offset + * to the end and didn't find enough space for the cluster, and we also + * didn't find any bitmaps that met our criteria, just go ahead and exit + */ + if (found_bitmap) { + ret = -ENOSPC; + goto out; + } + + cluster->points_to_bitmap = false; window_start = entry->offset; window_free = entry->bytes; last = entry; max_extent = entry->bytes; - while(1) { + while (1) { /* out window is just right, lets fill it */ if (window_free >= bytes + empty_size) break; node = rb_next(&last->offset_index); if (!node) { + if (found_bitmap) + goto again; ret = -ENOSPC; goto out; } next = rb_entry(node, struct btrfs_free_space, offset_index); + /* + * we found a bitmap, so if this search doesn't result in a + * cluster, we know to go and search again for the bitmaps and + * start looking for space there + */ + if (next->bitmap) { + if (!found_bitmap) + offset = next->offset; + found_bitmap = true; + last = next; + continue; + } + /* * we haven't filled the empty size and the window is * very large. reset and try again @@ -655,19 +1230,6 @@ again: window_free = entry->bytes; last = entry; max_extent = 0; - total_retries++; - if (total_retries % 64 == 0) { - if (min_bytes >= (bytes + empty_size)) { - ret = -ENOSPC; - goto out; - } - /* - * grow our allocation a bit, we're not having - * much luck - */ - min_bytes *= 2; - goto again; - } } else { last = next; window_free += next->bytes; @@ -685,11 +1247,19 @@ again: * The cluster includes an rbtree, but only uses the offset index * of each free space cache entry. */ - while(1) { + while (1) { node = rb_next(&entry->offset_index); - unlink_free_space(block_group, entry); + if (entry->bitmap && node) { + entry = rb_entry(node, struct btrfs_free_space, + offset_index); + continue; + } else if (entry->bitmap && !node) { + break; + } + + rb_erase(&entry->offset_index, &block_group->free_space_offset); ret = tree_insert_offset(&cluster->root, entry->offset, - &entry->offset_index); + &entry->offset_index, 0); BUG_ON(ret); if (!node || entry == last) @@ -697,8 +1267,10 @@ again: entry = rb_entry(node, struct btrfs_free_space, offset_index); } - ret = 0; + cluster->max_size = max_extent; +got_it: + ret = 0; atomic_inc(&block_group->count); list_add_tail(&cluster->block_group_list, &block_group->cluster_list); cluster->block_group = block_group; @@ -718,6 +1290,7 @@ void btrfs_init_free_cluster(struct btrfs_free_cluster *cluster) spin_lock_init(&cluster->refill_lock); cluster->root.rb_node = NULL; cluster->max_size = 0; + cluster->points_to_bitmap = false; INIT_LIST_HEAD(&cluster->block_group_list); cluster->block_group = NULL; } diff --git a/fs/btrfs/free-space-cache.h b/fs/btrfs/free-space-cache.h index 266fb876405..890a8e79011 100644 --- a/fs/btrfs/free-space-cache.h +++ b/fs/btrfs/free-space-cache.h @@ -19,6 +19,14 @@ #ifndef __BTRFS_FREE_SPACE_CACHE #define __BTRFS_FREE_SPACE_CACHE +struct btrfs_free_space { + struct rb_node offset_index; + u64 offset; + u64 bytes; + unsigned long *bitmap; + struct list_head list; +}; + int btrfs_add_free_space(struct btrfs_block_group_cache *block_group, u64 bytenr, u64 size); int btrfs_remove_free_space(struct btrfs_block_group_cache *block_group, -- GitLab From 817d52f8dba26d0295c26035531c30ce5f1e3c3e Mon Sep 17 00:00:00 2001 From: Josef Bacik Date: Mon, 13 Jul 2009 21:29:25 -0400 Subject: [PATCH 0269/1342] Btrfs: async block group caching This patch moves the caching of the block group off to a kthread in order to allow people to allocate sooner. Instead of blocking up behind the caching mutex, we instead kick of the caching kthread, and then attempt to make an allocation. If we cannot, we wait on the block groups caching waitqueue, which the caching kthread will wake the waiting threads up everytime it finds 2 meg worth of space, and then again when its finished caching. This is how I tested the speedup from this mkfs the disk mount the disk fill the disk up with fs_mark unmount the disk mount the disk time touch /mnt/foo Without my changes this took 11 seconds on my box, with these changes it now takes 1 second. Another change thats been put in place is we lock the super mirror's in the pinned extent map in order to keep us from adding that stuff as free space when caching the block group. This doesn't really change anything else as far as the pinned extent map is concerned, since for actual pinned extents we use EXTENT_DIRTY, but it does mean that when we unmount we have to go in and unlock those extents to keep from leaking memory. I've also added a check where when we are reading block groups from disk, if the amount of space used == the size of the block group, we go ahead and mark the block group as cached. This drastically reduces the amount of time it takes to cache the block groups. Using the same test as above, except doing a dd to a file and then unmounting, it used to take 33 seconds to umount, now it takes 3 seconds. This version uses the commit_root in the caching kthread, and then keeps track of how many async caching threads are running at any given time so if one of the async threads is still running as we cross transactions we can wait until its finished before handling the pinned extents. Thank you, Signed-off-by: Josef Bacik Signed-off-by: Chris Mason --- fs/btrfs/ctree.h | 22 +- fs/btrfs/disk-io.c | 3 + fs/btrfs/extent-tree.c | 471 +++++++++++++++++++++++++++++------- fs/btrfs/free-space-cache.c | 42 ++-- fs/btrfs/transaction.c | 23 +- fs/btrfs/tree-log.c | 2 +- 6 files changed, 439 insertions(+), 124 deletions(-) diff --git a/fs/btrfs/ctree.h b/fs/btrfs/ctree.h index 0cbf3491bb7..42b03c4ee49 100644 --- a/fs/btrfs/ctree.h +++ b/fs/btrfs/ctree.h @@ -691,6 +691,7 @@ struct btrfs_space_info { struct list_head block_groups; spinlock_t lock; struct rw_semaphore groups_sem; + atomic_t caching_threads; }; /* @@ -721,11 +722,17 @@ struct btrfs_free_cluster { struct list_head block_group_list; }; +enum btrfs_caching_type { + BTRFS_CACHE_NO = 0, + BTRFS_CACHE_STARTED = 1, + BTRFS_CACHE_FINISHED = 2, +}; + struct btrfs_block_group_cache { struct btrfs_key key; struct btrfs_block_group_item item; + struct btrfs_fs_info *fs_info; spinlock_t lock; - struct mutex cache_mutex; u64 pinned; u64 reserved; u64 flags; @@ -733,15 +740,19 @@ struct btrfs_block_group_cache { int extents_thresh; int free_extents; int total_bitmaps; - int cached; int ro; int dirty; + /* cache tracking stuff */ + wait_queue_head_t caching_q; + int cached; + struct btrfs_space_info *space_info; /* free space cache stuff */ spinlock_t tree_lock; struct rb_root free_space_offset; + u64 free_space; /* block group cache stuff */ struct rb_node cache_node; @@ -834,6 +845,7 @@ struct btrfs_fs_info { atomic_t async_submit_draining; atomic_t nr_async_bios; atomic_t async_delalloc_pages; + atomic_t async_caching_threads; /* * this is used by the balancing code to wait for all the pending @@ -950,6 +962,9 @@ struct btrfs_root { /* the node lock is held while changing the node pointer */ spinlock_t node_lock; + /* taken when updating the commit root */ + struct rw_semaphore commit_root_sem; + struct extent_buffer *commit_root; struct btrfs_root *log_root; struct btrfs_root *reloc_root; @@ -1911,7 +1926,7 @@ int btrfs_run_delayed_refs(struct btrfs_trans_handle *trans, struct btrfs_root *root, unsigned long count); int btrfs_lookup_extent(struct btrfs_root *root, u64 start, u64 len); int btrfs_update_pinned_extents(struct btrfs_root *root, - u64 bytenr, u64 num, int pin); + u64 bytenr, u64 num, int pin, int mark_free); int btrfs_drop_leaf_ref(struct btrfs_trans_handle *trans, struct btrfs_root *root, struct extent_buffer *leaf); int btrfs_cross_ref_exist(struct btrfs_trans_handle *trans, @@ -1996,6 +2011,7 @@ void btrfs_delalloc_reserve_space(struct btrfs_root *root, struct inode *inode, u64 bytes); void btrfs_delalloc_free_space(struct btrfs_root *root, struct inode *inode, u64 bytes); +void btrfs_free_super_mirror_extents(struct btrfs_fs_info *info); /* ctree.c */ int btrfs_bin_search(struct extent_buffer *eb, struct btrfs_key *key, int level, int *slot); diff --git a/fs/btrfs/disk-io.c b/fs/btrfs/disk-io.c index 55d9d188e69..ec2c915f7f4 100644 --- a/fs/btrfs/disk-io.c +++ b/fs/btrfs/disk-io.c @@ -907,6 +907,7 @@ static int __setup_root(u32 nodesize, u32 leafsize, u32 sectorsize, spin_lock_init(&root->inode_lock); mutex_init(&root->objectid_mutex); mutex_init(&root->log_mutex); + init_rwsem(&root->commit_root_sem); init_waitqueue_head(&root->log_writer_wait); init_waitqueue_head(&root->log_commit_wait[0]); init_waitqueue_head(&root->log_commit_wait[1]); @@ -1566,6 +1567,7 @@ struct btrfs_root *open_ctree(struct super_block *sb, atomic_set(&fs_info->async_delalloc_pages, 0); atomic_set(&fs_info->async_submit_draining, 0); atomic_set(&fs_info->nr_async_bios, 0); + atomic_set(&fs_info->async_caching_threads, 0); fs_info->sb = sb; fs_info->max_extent = (u64)-1; fs_info->max_inline = 8192 * 1024; @@ -2337,6 +2339,7 @@ int close_ctree(struct btrfs_root *root) free_extent_buffer(root->fs_info->csum_root->commit_root); btrfs_free_block_groups(root->fs_info); + btrfs_free_super_mirror_extents(root->fs_info); del_fs_roots(fs_info); diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c index 98697be6bdd..9a489cc89fd 100644 --- a/fs/btrfs/extent-tree.c +++ b/fs/btrfs/extent-tree.c @@ -21,6 +21,7 @@ #include #include #include +#include #include "compat.h" #include "hash.h" #include "ctree.h" @@ -61,6 +62,13 @@ static int do_chunk_alloc(struct btrfs_trans_handle *trans, struct btrfs_root *extent_root, u64 alloc_bytes, u64 flags, int force); +static noinline int +block_group_cache_done(struct btrfs_block_group_cache *cache) +{ + smp_mb(); + return cache->cached == BTRFS_CACHE_FINISHED; +} + static int block_group_bits(struct btrfs_block_group_cache *cache, u64 bits) { return (cache->flags & bits) == bits; @@ -145,21 +153,64 @@ block_group_cache_tree_search(struct btrfs_fs_info *info, u64 bytenr, return ret; } +void btrfs_free_super_mirror_extents(struct btrfs_fs_info *info) +{ + u64 start, end, last = 0; + int ret; + + while (1) { + ret = find_first_extent_bit(&info->pinned_extents, last, + &start, &end, EXTENT_LOCKED); + if (ret) + break; + + unlock_extent(&info->pinned_extents, start, end, GFP_NOFS); + last = end+1; + } +} + +static int remove_sb_from_cache(struct btrfs_root *root, + struct btrfs_block_group_cache *cache) +{ + struct btrfs_fs_info *fs_info = root->fs_info; + u64 bytenr; + u64 *logical; + int stripe_len; + int i, nr, ret; + + for (i = 0; i < BTRFS_SUPER_MIRROR_MAX; i++) { + bytenr = btrfs_sb_offset(i); + ret = btrfs_rmap_block(&root->fs_info->mapping_tree, + cache->key.objectid, bytenr, + 0, &logical, &nr, &stripe_len); + BUG_ON(ret); + while (nr--) { + try_lock_extent(&fs_info->pinned_extents, + logical[nr], + logical[nr] + stripe_len - 1, GFP_NOFS); + } + kfree(logical); + } + + return 0; +} + /* * this is only called by cache_block_group, since we could have freed extents * we need to check the pinned_extents for any extents that can't be used yet * since their free space will be released as soon as the transaction commits. */ -static int add_new_free_space(struct btrfs_block_group_cache *block_group, +static u64 add_new_free_space(struct btrfs_block_group_cache *block_group, struct btrfs_fs_info *info, u64 start, u64 end) { - u64 extent_start, extent_end, size; + u64 extent_start, extent_end, size, total_added = 0; int ret; while (start < end) { ret = find_first_extent_bit(&info->pinned_extents, start, &extent_start, &extent_end, - EXTENT_DIRTY); + EXTENT_DIRTY|EXTENT_LOCKED| + EXTENT_DELALLOC); if (ret) break; @@ -167,6 +218,7 @@ static int add_new_free_space(struct btrfs_block_group_cache *block_group, start = extent_end + 1; } else if (extent_start > start && extent_start < end) { size = extent_start - start; + total_added += size; ret = btrfs_add_free_space(block_group, start, size); BUG_ON(ret); @@ -178,84 +230,139 @@ static int add_new_free_space(struct btrfs_block_group_cache *block_group, if (start < end) { size = end - start; + total_added += size; ret = btrfs_add_free_space(block_group, start, size); BUG_ON(ret); } - return 0; + return total_added; } -static int remove_sb_from_cache(struct btrfs_root *root, - struct btrfs_block_group_cache *cache) +DEFINE_MUTEX(discard_mutex); + +/* + * if async kthreads are running when we cross transactions, we mark any pinned + * extents with EXTENT_DELALLOC and then let the caching kthreads clean up those + * extents when they are done. Also we run this from btrfs_finish_extent_commit + * in case there were some pinned extents that were missed because we had + * already cached that block group. + */ +static void btrfs_discard_pinned_extents(struct btrfs_fs_info *fs_info, + struct btrfs_block_group_cache *cache) { - u64 bytenr; - u64 *logical; - int stripe_len; - int i, nr, ret; + u64 start, end, last; + int ret; - for (i = 0; i < BTRFS_SUPER_MIRROR_MAX; i++) { - bytenr = btrfs_sb_offset(i); - ret = btrfs_rmap_block(&root->fs_info->mapping_tree, - cache->key.objectid, bytenr, 0, - &logical, &nr, &stripe_len); - BUG_ON(ret); - while (nr--) { - btrfs_remove_free_space(cache, logical[nr], - stripe_len); + if (!cache) + last = 0; + else + last = cache->key.objectid; + + mutex_lock(&discard_mutex); + while (1) { + ret = find_first_extent_bit(&fs_info->pinned_extents, last, + &start, &end, EXTENT_DELALLOC); + if (ret) + break; + + if (cache && start >= cache->key.objectid + cache->key.offset) + break; + + + if (!cache) { + cache = btrfs_lookup_block_group(fs_info, start); + BUG_ON(!cache); + + start = max(start, cache->key.objectid); + end = min(end, cache->key.objectid + cache->key.offset - 1); + + if (block_group_cache_done(cache)) + btrfs_add_free_space(cache, start, + end - start + 1); + cache = NULL; + } else { + start = max(start, cache->key.objectid); + end = min(end, cache->key.objectid + cache->key.offset - 1); + btrfs_add_free_space(cache, start, end - start + 1); + } + + clear_extent_bits(&fs_info->pinned_extents, start, end, + EXTENT_DELALLOC, GFP_NOFS); + last = end + 1; + + if (need_resched()) { + mutex_unlock(&discard_mutex); + cond_resched(); + mutex_lock(&discard_mutex); } - kfree(logical); } - return 0; + mutex_unlock(&discard_mutex); } -static int cache_block_group(struct btrfs_root *root, - struct btrfs_block_group_cache *block_group) +static int caching_kthread(void *data) { + struct btrfs_block_group_cache *block_group = data; + struct btrfs_fs_info *fs_info = block_group->fs_info; + u64 last = 0; struct btrfs_path *path; int ret = 0; struct btrfs_key key; struct extent_buffer *leaf; int slot; - u64 last; - - if (!block_group) - return 0; + u64 total_found = 0; - root = root->fs_info->extent_root; - - if (block_group->cached) - return 0; + BUG_ON(!fs_info); path = btrfs_alloc_path(); if (!path) return -ENOMEM; - path->reada = 2; + atomic_inc(&fs_info->async_caching_threads); + atomic_inc(&block_group->space_info->caching_threads); + last = max_t(u64, block_group->key.objectid, BTRFS_SUPER_INFO_OFFSET); +again: + /* need to make sure the commit_root doesn't disappear */ + down_read(&fs_info->extent_root->commit_root_sem); + /* - * we get into deadlocks with paths held by callers of this function. - * since the alloc_mutex is protecting things right now, just - * skip the locking here + * We don't want to deadlock with somebody trying to allocate a new + * extent for the extent root while also trying to search the extent + * root to add free space. So we skip locking and search the commit + * root, since its read-only */ path->skip_locking = 1; - last = max_t(u64, block_group->key.objectid, BTRFS_SUPER_INFO_OFFSET); + path->search_commit_root = 1; + path->reada = 2; + key.objectid = last; key.offset = 0; btrfs_set_key_type(&key, BTRFS_EXTENT_ITEM_KEY); - ret = btrfs_search_slot(NULL, root, &key, path, 0, 0); + ret = btrfs_search_slot(NULL, fs_info->extent_root, &key, path, 0, 0); if (ret < 0) goto err; while (1) { + smp_mb(); + if (block_group->fs_info->closing) + break; + leaf = path->nodes[0]; slot = path->slots[0]; if (slot >= btrfs_header_nritems(leaf)) { - ret = btrfs_next_leaf(root, path); + ret = btrfs_next_leaf(fs_info->extent_root, path); if (ret < 0) goto err; - if (ret == 0) - continue; - else + else if (ret) break; + + if (need_resched()) { + btrfs_release_path(fs_info->extent_root, path); + up_read(&fs_info->extent_root->commit_root_sem); + cond_resched(); + goto again; + } + + continue; } btrfs_item_key_to_cpu(leaf, &key, slot); if (key.objectid < block_group->key.objectid) @@ -266,24 +373,63 @@ static int cache_block_group(struct btrfs_root *root, break; if (btrfs_key_type(&key) == BTRFS_EXTENT_ITEM_KEY) { - add_new_free_space(block_group, root->fs_info, last, - key.objectid); - + total_found += add_new_free_space(block_group, + fs_info, last, + key.objectid); last = key.objectid + key.offset; } + + if (total_found > (1024 * 1024 * 2)) { + total_found = 0; + wake_up(&block_group->caching_q); + } next: path->slots[0]++; } + ret = 0; - add_new_free_space(block_group, root->fs_info, last, - block_group->key.objectid + - block_group->key.offset); + total_found += add_new_free_space(block_group, fs_info, last, + block_group->key.objectid + + block_group->key.offset); + + spin_lock(&block_group->lock); + block_group->cached = BTRFS_CACHE_FINISHED; + spin_unlock(&block_group->lock); - block_group->cached = 1; - remove_sb_from_cache(root, block_group); - ret = 0; err: btrfs_free_path(path); + up_read(&fs_info->extent_root->commit_root_sem); + atomic_dec(&fs_info->async_caching_threads); + atomic_dec(&block_group->space_info->caching_threads); + wake_up(&block_group->caching_q); + + if (!ret) + btrfs_discard_pinned_extents(fs_info, block_group); + + return 0; +} + +static int cache_block_group(struct btrfs_block_group_cache *cache) +{ + struct task_struct *tsk; + int ret = 0; + + spin_lock(&cache->lock); + if (cache->cached != BTRFS_CACHE_NO) { + spin_unlock(&cache->lock); + return ret; + } + cache->cached = BTRFS_CACHE_STARTED; + spin_unlock(&cache->lock); + + tsk = kthread_run(caching_kthread, cache, "btrfs-cache-%llu\n", + cache->key.objectid); + if (IS_ERR(tsk)) { + ret = PTR_ERR(tsk); + printk(KERN_ERR "error running thread %d\n", ret); + BUG(); + } + return ret; } @@ -1721,7 +1867,7 @@ static int run_one_delayed_ref(struct btrfs_trans_handle *trans, BUG_ON(ret); } btrfs_update_pinned_extents(root, node->bytenr, - node->num_bytes, 1); + node->num_bytes, 1, 0); update_reserved_extents(root, node->bytenr, node->num_bytes, 0); } @@ -2496,6 +2642,7 @@ static int update_space_info(struct btrfs_fs_info *info, u64 flags, found->force_alloc = 0; *space_info = found; list_add_rcu(&found->list, &info->space_info); + atomic_set(&found->caching_threads, 0); return 0; } @@ -2953,7 +3100,7 @@ static u64 first_logical_byte(struct btrfs_root *root, u64 search_start) } int btrfs_update_pinned_extents(struct btrfs_root *root, - u64 bytenr, u64 num, int pin) + u64 bytenr, u64 num, int pin, int mark_free) { u64 len; struct btrfs_block_group_cache *cache; @@ -2988,7 +3135,7 @@ int btrfs_update_pinned_extents(struct btrfs_root *root, spin_unlock(&cache->lock); spin_unlock(&cache->space_info->lock); fs_info->total_pinned -= len; - if (cache->cached) + if (block_group_cache_done(cache) && mark_free) btrfs_add_free_space(cache, bytenr, len); } btrfs_put_block_group(cache); @@ -3034,14 +3181,27 @@ int btrfs_copy_pinned(struct btrfs_root *root, struct extent_io_tree *copy) u64 last = 0; u64 start; u64 end; + bool caching_kthreads = false; struct extent_io_tree *pinned_extents = &root->fs_info->pinned_extents; int ret; + if (atomic_read(&root->fs_info->async_caching_threads)) + caching_kthreads = true; + while (1) { ret = find_first_extent_bit(pinned_extents, last, &start, &end, EXTENT_DIRTY); if (ret) break; + + /* + * we need to make sure that the pinned extents don't go away + * while we are caching block groups + */ + if (unlikely(caching_kthreads)) + set_extent_delalloc(pinned_extents, start, end, + GFP_NOFS); + set_extent_dirty(copy, start, end, GFP_NOFS); last = end + 1; } @@ -3055,6 +3215,12 @@ int btrfs_finish_extent_commit(struct btrfs_trans_handle *trans, u64 start; u64 end; int ret; + int mark_free = 1; + + ret = find_first_extent_bit(&root->fs_info->pinned_extents, 0, + &start, &end, EXTENT_DELALLOC); + if (!ret) + mark_free = 0; while (1) { ret = find_first_extent_bit(unpin, 0, &start, &end, @@ -3065,11 +3231,16 @@ int btrfs_finish_extent_commit(struct btrfs_trans_handle *trans, ret = btrfs_discard_extent(root, start, end + 1 - start); /* unlocks the pinned mutex */ - btrfs_update_pinned_extents(root, start, end + 1 - start, 0); + btrfs_update_pinned_extents(root, start, end + 1 - start, 0, + mark_free); clear_extent_dirty(unpin, start, end, GFP_NOFS); cond_resched(); } + + if (unlikely(!mark_free)) + btrfs_discard_pinned_extents(root->fs_info, NULL); + return ret; } @@ -3110,7 +3281,7 @@ static int pin_down_bytes(struct btrfs_trans_handle *trans, pinit: btrfs_set_path_blocking(path); /* unlocks the pinned mutex */ - btrfs_update_pinned_extents(root, bytenr, num_bytes, 1); + btrfs_update_pinned_extents(root, bytenr, num_bytes, 1, 0); BUG_ON(err < 0); return 0; @@ -3421,7 +3592,7 @@ int btrfs_free_extent(struct btrfs_trans_handle *trans, if (root_objectid == BTRFS_TREE_LOG_OBJECTID) { WARN_ON(owner >= BTRFS_FIRST_FREE_OBJECTID); /* unlocks the pinned mutex */ - btrfs_update_pinned_extents(root, bytenr, num_bytes, 1); + btrfs_update_pinned_extents(root, bytenr, num_bytes, 1, 0); update_reserved_extents(root, bytenr, num_bytes, 0); ret = 0; } else if (owner < BTRFS_FIRST_FREE_OBJECTID) { @@ -3447,6 +3618,45 @@ static u64 stripe_align(struct btrfs_root *root, u64 val) return ret; } +/* + * when we wait for progress in the block group caching, its because + * our allocation attempt failed at least once. So, we must sleep + * and let some progress happen before we try again. + * + * This function will sleep at least once waiting for new free space to + * show up, and then it will check the block group free space numbers + * for our min num_bytes. Another option is to have it go ahead + * and look in the rbtree for a free extent of a given size, but this + * is a good start. + */ +static noinline int +wait_block_group_cache_progress(struct btrfs_block_group_cache *cache, + u64 num_bytes) +{ + DEFINE_WAIT(wait); + + prepare_to_wait(&cache->caching_q, &wait, TASK_UNINTERRUPTIBLE); + + if (block_group_cache_done(cache)) { + finish_wait(&cache->caching_q, &wait); + return 0; + } + schedule(); + finish_wait(&cache->caching_q, &wait); + + wait_event(cache->caching_q, block_group_cache_done(cache) || + (cache->free_space >= num_bytes)); + return 0; +} + +enum btrfs_loop_type { + LOOP_CACHED_ONLY = 0, + LOOP_CACHING_NOWAIT = 1, + LOOP_CACHING_WAIT = 2, + LOOP_ALLOC_CHUNK = 3, + LOOP_NO_EMPTY_SIZE = 4, +}; + /* * walks the btree of allocated extents and find a hole of a given size. * The key ins is changed to record the hole: @@ -3472,6 +3682,7 @@ static noinline int find_free_extent(struct btrfs_trans_handle *trans, struct btrfs_space_info *space_info; int last_ptr_loop = 0; int loop = 0; + bool found_uncached_bg = false; WARN_ON(num_bytes < root->sectorsize); btrfs_set_key_type(ins, BTRFS_EXTENT_ITEM_KEY); @@ -3503,15 +3714,18 @@ static noinline int find_free_extent(struct btrfs_trans_handle *trans, search_start = max(search_start, first_logical_byte(root, 0)); search_start = max(search_start, hint_byte); - if (!last_ptr) { + if (!last_ptr) empty_cluster = 0; - loop = 1; - } if (search_start == hint_byte) { block_group = btrfs_lookup_block_group(root->fs_info, search_start); - if (block_group && block_group_bits(block_group, data)) { + /* + * we don't want to use the block group if it doesn't match our + * allocation bits, or if its not cached. + */ + if (block_group && block_group_bits(block_group, data) && + block_group_cache_done(block_group)) { down_read(&space_info->groups_sem); if (list_empty(&block_group->list) || block_group->ro) { @@ -3534,21 +3748,35 @@ search: down_read(&space_info->groups_sem); list_for_each_entry(block_group, &space_info->block_groups, list) { u64 offset; + int cached; atomic_inc(&block_group->count); search_start = block_group->key.objectid; have_block_group: - if (unlikely(!block_group->cached)) { - mutex_lock(&block_group->cache_mutex); - ret = cache_block_group(root, block_group); - mutex_unlock(&block_group->cache_mutex); - if (ret) { - btrfs_put_block_group(block_group); - break; + if (unlikely(block_group->cached == BTRFS_CACHE_NO)) { + /* + * we want to start caching kthreads, but not too many + * right off the bat so we don't overwhelm the system, + * so only start them if there are less than 2 and we're + * in the initial allocation phase. + */ + if (loop > LOOP_CACHING_NOWAIT || + atomic_read(&space_info->caching_threads) < 2) { + ret = cache_block_group(block_group); + BUG_ON(ret); } } + cached = block_group_cache_done(block_group); + if (unlikely(!cached)) { + found_uncached_bg = true; + + /* if we only want cached bgs, loop */ + if (loop == LOOP_CACHED_ONLY) + goto loop; + } + if (unlikely(block_group->ro)) goto loop; @@ -3627,14 +3855,21 @@ refill_cluster: spin_unlock(&last_ptr->refill_lock); goto checks; } + } else if (!cached && loop > LOOP_CACHING_NOWAIT) { + spin_unlock(&last_ptr->refill_lock); + + wait_block_group_cache_progress(block_group, + num_bytes + empty_cluster + empty_size); + goto have_block_group; } + /* * at this point we either didn't find a cluster * or we weren't able to allocate a block from our * cluster. Free the cluster we've been trying * to use, and go to the next block group */ - if (loop < 2) { + if (loop < LOOP_NO_EMPTY_SIZE) { btrfs_return_cluster_to_free_space(NULL, last_ptr); spin_unlock(&last_ptr->refill_lock); @@ -3645,8 +3880,15 @@ refill_cluster: offset = btrfs_find_space_for_alloc(block_group, search_start, num_bytes, empty_size); - if (!offset) + if (!offset && (cached || (!cached && + loop == LOOP_CACHING_NOWAIT))) { goto loop; + } else if (!offset && (!cached && + loop > LOOP_CACHING_NOWAIT)) { + wait_block_group_cache_progress(block_group, + num_bytes + empty_size); + goto have_block_group; + } checks: search_start = stripe_align(root, offset); /* move on to the next group */ @@ -3694,13 +3936,26 @@ loop: } up_read(&space_info->groups_sem); - /* loop == 0, try to find a clustered alloc in every block group - * loop == 1, try again after forcing a chunk allocation - * loop == 2, set empty_size and empty_cluster to 0 and try again + /* LOOP_CACHED_ONLY, only search fully cached block groups + * LOOP_CACHING_NOWAIT, search partially cached block groups, but + * dont wait foR them to finish caching + * LOOP_CACHING_WAIT, search everything, and wait if our bg is caching + * LOOP_ALLOC_CHUNK, force a chunk allocation and try again + * LOOP_NO_EMPTY_SIZE, set empty_size and empty_cluster to 0 and try + * again */ - if (!ins->objectid && loop < 3 && - (empty_size || empty_cluster || allowed_chunk_alloc)) { - if (loop >= 2) { + if (!ins->objectid && loop < LOOP_NO_EMPTY_SIZE && + (found_uncached_bg || empty_size || empty_cluster || + allowed_chunk_alloc)) { + if (found_uncached_bg) { + found_uncached_bg = false; + if (loop < LOOP_CACHING_WAIT) { + loop++; + goto search; + } + } + + if (loop == LOOP_ALLOC_CHUNK) { empty_size = 0; empty_cluster = 0; } @@ -3713,7 +3968,7 @@ loop: space_info->force_alloc = 1; } - if (loop < 3) { + if (loop < LOOP_NO_EMPTY_SIZE) { loop++; goto search; } @@ -3809,7 +4064,7 @@ again: num_bytes, data, 1); goto again; } - if (ret) { + if (ret == -ENOSPC) { struct btrfs_space_info *sinfo; sinfo = __find_space_info(root->fs_info, data); @@ -3817,7 +4072,6 @@ again: "wanted %llu\n", (unsigned long long)data, (unsigned long long)num_bytes); dump_space_info(sinfo, num_bytes); - BUG(); } return ret; @@ -3855,7 +4109,9 @@ int btrfs_reserve_extent(struct btrfs_trans_handle *trans, ret = __btrfs_reserve_extent(trans, root, num_bytes, min_alloc_size, empty_size, hint_byte, search_end, ins, data); - update_reserved_extents(root, ins->objectid, ins->offset, 1); + if (!ret) + update_reserved_extents(root, ins->objectid, ins->offset, 1); + return ret; } @@ -4017,9 +4273,9 @@ int btrfs_alloc_logged_file_extent(struct btrfs_trans_handle *trans, struct btrfs_block_group_cache *block_group; block_group = btrfs_lookup_block_group(root->fs_info, ins->objectid); - mutex_lock(&block_group->cache_mutex); - cache_block_group(root, block_group); - mutex_unlock(&block_group->cache_mutex); + cache_block_group(block_group); + wait_event(block_group->caching_q, + block_group_cache_done(block_group)); ret = btrfs_remove_free_space(block_group, ins->objectid, ins->offset); @@ -4050,7 +4306,8 @@ static int alloc_tree_block(struct btrfs_trans_handle *trans, ret = __btrfs_reserve_extent(trans, root, num_bytes, num_bytes, empty_size, hint_byte, search_end, ins, 0); - BUG_ON(ret); + if (ret) + return ret; if (root_objectid == BTRFS_TREE_RELOC_OBJECTID) { if (parent == 0) @@ -6966,11 +7223,16 @@ int btrfs_free_block_groups(struct btrfs_fs_info *info) &info->block_group_cache_tree); spin_unlock(&info->block_group_cache_lock); - btrfs_remove_free_space_cache(block_group); down_write(&block_group->space_info->groups_sem); list_del(&block_group->list); up_write(&block_group->space_info->groups_sem); + if (block_group->cached == BTRFS_CACHE_STARTED) + wait_event(block_group->caching_q, + block_group_cache_done(block_group)); + + btrfs_remove_free_space_cache(block_group); + WARN_ON(atomic_read(&block_group->count) != 1); kfree(block_group); @@ -7036,10 +7298,10 @@ int btrfs_read_block_groups(struct btrfs_root *root) atomic_set(&cache->count, 1); spin_lock_init(&cache->lock); spin_lock_init(&cache->tree_lock); - mutex_init(&cache->cache_mutex); + cache->fs_info = info; + init_waitqueue_head(&cache->caching_q); INIT_LIST_HEAD(&cache->list); INIT_LIST_HEAD(&cache->cluster_list); - cache->sectorsize = root->sectorsize; /* * we only want to have 32k of ram per block group for keeping @@ -7057,6 +7319,26 @@ int btrfs_read_block_groups(struct btrfs_root *root) key.objectid = found_key.objectid + found_key.offset; btrfs_release_path(root, path); cache->flags = btrfs_block_group_flags(&cache->item); + cache->sectorsize = root->sectorsize; + + remove_sb_from_cache(root, cache); + + /* + * check for two cases, either we are full, and therefore + * don't need to bother with the caching work since we won't + * find any space, or we are empty, and we can just add all + * the space in and be done with it. This saves us _alot_ of + * time, particularly in the full case. + */ + if (found_key.offset == btrfs_block_group_used(&cache->item)) { + cache->cached = BTRFS_CACHE_FINISHED; + } else if (btrfs_block_group_used(&cache->item) == 0) { + cache->cached = BTRFS_CACHE_FINISHED; + add_new_free_space(cache, root->fs_info, + found_key.objectid, + found_key.objectid + + found_key.offset); + } ret = update_space_info(info, cache->flags, found_key.offset, btrfs_block_group_used(&cache->item), @@ -7112,7 +7394,7 @@ int btrfs_make_block_group(struct btrfs_trans_handle *trans, atomic_set(&cache->count, 1); spin_lock_init(&cache->lock); spin_lock_init(&cache->tree_lock); - mutex_init(&cache->cache_mutex); + init_waitqueue_head(&cache->caching_q); INIT_LIST_HEAD(&cache->list); INIT_LIST_HEAD(&cache->cluster_list); @@ -7121,11 +7403,12 @@ int btrfs_make_block_group(struct btrfs_trans_handle *trans, cache->flags = type; btrfs_set_block_group_flags(&cache->item, type); - cache->cached = 1; - ret = btrfs_add_free_space(cache, chunk_offset, size); - BUG_ON(ret); + cache->cached = BTRFS_CACHE_FINISHED; remove_sb_from_cache(root, cache); + add_new_free_space(cache, root->fs_info, chunk_offset, + chunk_offset + size); + ret = update_space_info(root->fs_info, cache->flags, size, bytes_used, &cache->space_info); BUG_ON(ret); @@ -7184,7 +7467,7 @@ int btrfs_remove_block_group(struct btrfs_trans_handle *trans, rb_erase(&block_group->cache_node, &root->fs_info->block_group_cache_tree); spin_unlock(&root->fs_info->block_group_cache_lock); - btrfs_remove_free_space_cache(block_group); + down_write(&block_group->space_info->groups_sem); /* * we must use list_del_init so people can check to see if they @@ -7193,6 +7476,12 @@ int btrfs_remove_block_group(struct btrfs_trans_handle *trans, list_del_init(&block_group->list); up_write(&block_group->space_info->groups_sem); + if (block_group->cached == BTRFS_CACHE_STARTED) + wait_event(block_group->caching_q, + block_group_cache_done(block_group)); + + btrfs_remove_free_space_cache(block_group); + spin_lock(&block_group->space_info->lock); block_group->space_info->total_bytes -= block_group->key.offset; block_group->space_info->bytes_readonly -= block_group->key.offset; diff --git a/fs/btrfs/free-space-cache.c b/fs/btrfs/free-space-cache.c index ab8cad8b46c..af99b78b288 100644 --- a/fs/btrfs/free-space-cache.c +++ b/fs/btrfs/free-space-cache.c @@ -238,6 +238,7 @@ static void unlink_free_space(struct btrfs_block_group_cache *block_group, { rb_erase(&info->offset_index, &block_group->free_space_offset); block_group->free_extents--; + block_group->free_space -= info->bytes; } static int link_free_space(struct btrfs_block_group_cache *block_group, @@ -251,6 +252,7 @@ static int link_free_space(struct btrfs_block_group_cache *block_group, if (ret) return ret; + block_group->free_space += info->bytes; block_group->free_extents++; return ret; } @@ -285,36 +287,40 @@ static void recalculate_thresholds(struct btrfs_block_group_cache *block_group) } } -static void bitmap_clear_bits(struct btrfs_free_space *info, u64 offset, u64 bytes, - u64 sectorsize) +static void bitmap_clear_bits(struct btrfs_block_group_cache *block_group, + struct btrfs_free_space *info, u64 offset, + u64 bytes) { unsigned long start, end; unsigned long i; - start = offset_to_bit(info->offset, sectorsize, offset); - end = start + bytes_to_bits(bytes, sectorsize); + start = offset_to_bit(info->offset, block_group->sectorsize, offset); + end = start + bytes_to_bits(bytes, block_group->sectorsize); BUG_ON(end > BITS_PER_BITMAP); for (i = start; i < end; i++) clear_bit(i, info->bitmap); info->bytes -= bytes; + block_group->free_space -= bytes; } -static void bitmap_set_bits(struct btrfs_free_space *info, u64 offset, u64 bytes, - u64 sectorsize) +static void bitmap_set_bits(struct btrfs_block_group_cache *block_group, + struct btrfs_free_space *info, u64 offset, + u64 bytes) { unsigned long start, end; unsigned long i; - start = offset_to_bit(info->offset, sectorsize, offset); - end = start + bytes_to_bits(bytes, sectorsize); + start = offset_to_bit(info->offset, block_group->sectorsize, offset); + end = start + bytes_to_bits(bytes, block_group->sectorsize); BUG_ON(end > BITS_PER_BITMAP); for (i = start; i < end; i++) set_bit(i, info->bitmap); info->bytes += bytes; + block_group->free_space += bytes; } static int search_bitmap(struct btrfs_block_group_cache *block_group, @@ -414,13 +420,12 @@ again: (u64)(BITS_PER_BITMAP * block_group->sectorsize) - 1; if (*offset > bitmap_info->offset && *offset + *bytes > end) { - bitmap_clear_bits(bitmap_info, *offset, - end - *offset + 1, block_group->sectorsize); + bitmap_clear_bits(block_group, bitmap_info, *offset, + end - *offset + 1); *bytes -= end - *offset + 1; *offset = end + 1; } else if (*offset >= bitmap_info->offset && *offset + *bytes <= end) { - bitmap_clear_bits(bitmap_info, *offset, - *bytes, block_group->sectorsize); + bitmap_clear_bits(block_group, bitmap_info, *offset, *bytes); *bytes = 0; } @@ -495,14 +500,13 @@ again: (u64)(BITS_PER_BITMAP * block_group->sectorsize); if (offset >= bitmap_info->offset && offset + bytes > end) { - bitmap_set_bits(bitmap_info, offset, end - offset, - block_group->sectorsize); + bitmap_set_bits(block_group, bitmap_info, offset, + end - offset); bytes -= end - offset; offset = end; added = 0; } else if (offset >= bitmap_info->offset && offset + bytes <= end) { - bitmap_set_bits(bitmap_info, offset, bytes, - block_group->sectorsize); + bitmap_set_bits(block_group, bitmap_info, offset, bytes); bytes = 0; } else { BUG(); @@ -870,8 +874,7 @@ u64 btrfs_find_space_for_alloc(struct btrfs_block_group_cache *block_group, ret = offset; if (entry->bitmap) { - bitmap_clear_bits(entry, offset, bytes, - block_group->sectorsize); + bitmap_clear_bits(block_group, entry, offset, bytes); if (!entry->bytes) { unlink_free_space(block_group, entry); kfree(entry->bitmap); @@ -891,6 +894,7 @@ u64 btrfs_find_space_for_alloc(struct btrfs_block_group_cache *block_group, out: spin_unlock(&block_group->tree_lock); + return ret; } @@ -967,7 +971,7 @@ static u64 btrfs_alloc_from_bitmap(struct btrfs_block_group_cache *block_group, goto out; ret = search_start; - bitmap_clear_bits(entry, ret, bytes, block_group->sectorsize); + bitmap_clear_bits(block_group, entry, ret, bytes); out: spin_unlock(&cluster->lock); spin_unlock(&block_group->tree_lock); diff --git a/fs/btrfs/transaction.c b/fs/btrfs/transaction.c index 81f7124c305..32454d1c566 100644 --- a/fs/btrfs/transaction.c +++ b/fs/btrfs/transaction.c @@ -40,6 +40,14 @@ static noinline void put_transaction(struct btrfs_transaction *transaction) } } +static noinline void switch_commit_root(struct btrfs_root *root) +{ + down_write(&root->commit_root_sem); + free_extent_buffer(root->commit_root); + root->commit_root = btrfs_root_node(root); + up_write(&root->commit_root_sem); +} + /* * either allocate a new transaction or hop into the existing one */ @@ -458,8 +466,7 @@ static int update_cowonly_root(struct btrfs_trans_handle *trans, ret = btrfs_write_dirty_block_groups(trans, root); BUG_ON(ret); } - free_extent_buffer(root->commit_root); - root->commit_root = btrfs_root_node(root); + switch_commit_root(root); return 0; } @@ -537,8 +544,7 @@ static noinline int commit_fs_roots(struct btrfs_trans_handle *trans, btrfs_update_reloc_root(trans, root); if (root->commit_root != root->node) { - free_extent_buffer(root->commit_root); - root->commit_root = btrfs_root_node(root); + switch_commit_root(root); btrfs_set_root_node(&root->root_item, root->node); } @@ -1002,15 +1008,11 @@ int btrfs_commit_transaction(struct btrfs_trans_handle *trans, btrfs_set_root_node(&root->fs_info->tree_root->root_item, root->fs_info->tree_root->node); - free_extent_buffer(root->fs_info->tree_root->commit_root); - root->fs_info->tree_root->commit_root = - btrfs_root_node(root->fs_info->tree_root); + switch_commit_root(root->fs_info->tree_root); btrfs_set_root_node(&root->fs_info->chunk_root->root_item, root->fs_info->chunk_root->node); - free_extent_buffer(root->fs_info->chunk_root->commit_root); - root->fs_info->chunk_root->commit_root = - btrfs_root_node(root->fs_info->chunk_root); + switch_commit_root(root->fs_info->chunk_root); update_super_roots(root); @@ -1050,6 +1052,7 @@ int btrfs_commit_transaction(struct btrfs_trans_handle *trans, cur_trans->commit_done = 1; root->fs_info->last_trans_committed = cur_trans->transid; + wake_up(&cur_trans->commit_wait); put_transaction(cur_trans); diff --git a/fs/btrfs/tree-log.c b/fs/btrfs/tree-log.c index c13922206d1..19560686261 100644 --- a/fs/btrfs/tree-log.c +++ b/fs/btrfs/tree-log.c @@ -264,7 +264,7 @@ static int process_one_buffer(struct btrfs_root *log, { if (wc->pin) btrfs_update_pinned_extents(log->fs_info->extent_root, - eb->start, eb->len, 1); + eb->start, eb->len, 1, 0); if (btrfs_buffer_uptodate(eb, gen)) { if (wc->write) -- GitLab From 8de56b7deb2534a586839eda52843c1dae680dc5 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Fri, 24 Jul 2009 16:51:47 +0200 Subject: [PATCH 0270/1342] ALSA: hda - Fix mute control with some ALC262 models The master mute switch is wrongly implemented as checking the pointer instead of its value, thus it can be never muted. This patch fixes the issue. Reference: Novell bnc#404873 https://bugzilla.novell.com/show_bug.cgi?id=404873 Signed-off-by: Takashi Iwai Cc: --- sound/pci/hda/patch_realtek.c | 33 ++++++++++++++++----------------- 1 file changed, 16 insertions(+), 17 deletions(-) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 7e99763ca52..8c8b273116f 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -10631,6 +10631,18 @@ static void alc262_lenovo_3000_unsol_event(struct hda_codec *codec, alc262_lenovo_3000_automute(codec, 1); } +static int amp_stereo_mute_update(struct hda_codec *codec, hda_nid_t nid, + int dir, int idx, long *valp) +{ + int i, change = 0; + + for (i = 0; i < 2; i++, valp++) + change |= snd_hda_codec_amp_update(codec, nid, i, dir, idx, + HDA_AMP_MUTE, + *valp ? 0 : HDA_AMP_MUTE); + return change; +} + /* bind hp and internal speaker mute (with plug check) */ static int alc262_fujitsu_master_sw_put(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_value *ucontrol) @@ -10639,13 +10651,8 @@ static int alc262_fujitsu_master_sw_put(struct snd_kcontrol *kcontrol, long *valp = ucontrol->value.integer.value; int change; - change = snd_hda_codec_amp_stereo(codec, 0x14, HDA_OUTPUT, 0, - HDA_AMP_MUTE, - valp ? 0 : HDA_AMP_MUTE); - change |= snd_hda_codec_amp_stereo(codec, 0x1b, HDA_OUTPUT, 0, - HDA_AMP_MUTE, - valp ? 0 : HDA_AMP_MUTE); - + change = amp_stereo_mute_update(codec, 0x14, HDA_OUTPUT, 0, valp); + change |= amp_stereo_mute_update(codec, 0x1b, HDA_OUTPUT, 0, valp); if (change) alc262_fujitsu_automute(codec, 0); return change; @@ -10680,10 +10687,7 @@ static int alc262_lenovo_3000_master_sw_put(struct snd_kcontrol *kcontrol, long *valp = ucontrol->value.integer.value; int change; - change = snd_hda_codec_amp_stereo(codec, 0x1b, HDA_OUTPUT, 0, - HDA_AMP_MUTE, - valp ? 0 : HDA_AMP_MUTE); - + change = amp_stereo_mute_update(codec, 0x1b, HDA_OUTPUT, 0, valp); if (change) alc262_lenovo_3000_automute(codec, 0); return change; @@ -11854,12 +11858,7 @@ static int alc268_acer_master_sw_put(struct snd_kcontrol *kcontrol, long *valp = ucontrol->value.integer.value; int change; - change = snd_hda_codec_amp_update(codec, 0x14, 0, HDA_OUTPUT, 0, - HDA_AMP_MUTE, - valp[0] ? 0 : HDA_AMP_MUTE); - change |= snd_hda_codec_amp_update(codec, 0x14, 1, HDA_OUTPUT, 0, - HDA_AMP_MUTE, - valp[1] ? 0 : HDA_AMP_MUTE); + change = amp_stereo_mute_update(codec, 0x14, HDA_OUTPUT, 0, valp); if (change) alc268_acer_automute(codec, 0); return change; -- GitLab From 20736abaa361bea488df6a1f66f6b37fb01107b9 Mon Sep 17 00:00:00 2001 From: Diego Calleja Date: Fri, 24 Jul 2009 11:06:52 -0400 Subject: [PATCH 0271/1342] Btrfs: Remove code duplication in comp_keys comp_keys is duplicating what is done in btrfs_comp_cpu_keys, so just call it. Signed-off-by: Diego Calleja Signed-off-by: Chris Mason --- fs/btrfs/ctree.c | 14 +------------- 1 file changed, 1 insertion(+), 13 deletions(-) diff --git a/fs/btrfs/ctree.c b/fs/btrfs/ctree.c index fdd423a550d..91572091c0a 100644 --- a/fs/btrfs/ctree.c +++ b/fs/btrfs/ctree.c @@ -557,19 +557,7 @@ static int comp_keys(struct btrfs_disk_key *disk, struct btrfs_key *k2) btrfs_disk_key_to_cpu(&k1, disk); - if (k1.objectid > k2->objectid) - return 1; - if (k1.objectid < k2->objectid) - return -1; - if (k1.type > k2->type) - return 1; - if (k1.type < k2->type) - return -1; - if (k1.offset > k2->offset) - return 1; - if (k1.offset < k2->offset) - return -1; - return 0; + return btrfs_comp_cpu_keys(&k1, k2); } /* -- GitLab From 1fcbac581be375ca0a686f72ee2b7fd1dbf386e7 Mon Sep 17 00:00:00 2001 From: Yan Zheng Date: Fri, 24 Jul 2009 11:06:53 -0400 Subject: [PATCH 0272/1342] Btrfs: find_free_dev_extent doesn't handle holes at the start of the device find_free_dev_extent does not properly handle the case where the device is not complete free, and there is a free extent at the beginning of the device. Signed-off-by: Yan Zheng Signed-off-by: Chris Mason --- fs/btrfs/volumes.c | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-) diff --git a/fs/btrfs/volumes.c b/fs/btrfs/volumes.c index 55c37276a29..074c1c56d8c 100644 --- a/fs/btrfs/volumes.c +++ b/fs/btrfs/volumes.c @@ -758,9 +758,13 @@ static noinline int find_free_dev_extent(struct btrfs_trans_handle *trans, ret = btrfs_search_slot(trans, root, &key, path, 0, 0); if (ret < 0) goto error; - ret = btrfs_previous_item(root, path, 0, key.type); - if (ret < 0) - goto error; + if (ret > 0) { + ret = btrfs_previous_item(root, path, key.objectid, key.type); + if (ret < 0) + goto error; + if (ret > 0) + start_found = 1; + } l = path->nodes[0]; btrfs_item_key_to_cpu(l, &key, path->slots[0]); while (1) { -- GitLab From 0a4eefbb745ec0e8a5b694ae3f40cc34082d8f61 Mon Sep 17 00:00:00 2001 From: Yan Zheng Date: Fri, 24 Jul 2009 11:06:53 -0400 Subject: [PATCH 0273/1342] Btrfs: Fix ordering of key field checks in btrfs_previous_item Check objectid of item before checking the item type, otherwise we may return zero for a key that is actually too low. Signed-off-by: Yan Zheng Signed-off-by: Chris Mason --- fs/btrfs/ctree.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/fs/btrfs/ctree.c b/fs/btrfs/ctree.c index 91572091c0a..978449af4cc 100644 --- a/fs/btrfs/ctree.c +++ b/fs/btrfs/ctree.c @@ -4296,10 +4296,10 @@ int btrfs_previous_item(struct btrfs_root *root, path->slots[0]--; btrfs_item_key_to_cpu(leaf, &found_key, path->slots[0]); - if (found_key.type == type) - return 0; if (found_key.objectid < min_objectid) break; + if (found_key.type == type) + return 0; if (found_key.objectid == min_objectid && found_key.type < type) break; -- GitLab From d717aa1d31c36cb56059e97966cb76f0be021969 Mon Sep 17 00:00:00 2001 From: Yan Zheng Date: Fri, 24 Jul 2009 12:42:46 -0400 Subject: [PATCH 0274/1342] Btrfs: Avoid delayed reference update looping btrfs_split_leaf and btrfs_del_items can end up in a loop where one is constantly spliting a given leaf and the other is constantly merging it back with the adjacent nodes. There is a better fix for this, but in the interest of something small, this patch just changes btrfs_del_items back to balancing less often. Signed-off-by: Chris Mason --- fs/btrfs/ctree.c | 5 +---- 1 file changed, 1 insertion(+), 4 deletions(-) diff --git a/fs/btrfs/ctree.c b/fs/btrfs/ctree.c index 978449af4cc..3fdcc0512d3 100644 --- a/fs/btrfs/ctree.c +++ b/fs/btrfs/ctree.c @@ -1040,9 +1040,6 @@ static noinline int balance_level(struct btrfs_trans_handle *trans, BTRFS_NODEPTRS_PER_BLOCK(root) / 4) return 0; - if (btrfs_header_nritems(mid) > 2) - return 0; - if (btrfs_header_nritems(mid) < 2) err_on_enospc = 1; @@ -3796,7 +3793,7 @@ int btrfs_del_items(struct btrfs_trans_handle *trans, struct btrfs_root *root, } /* delete the leaf if it is mostly empty */ - if (used < BTRFS_LEAF_DATA_SIZE(root) / 2) { + if (used < BTRFS_LEAF_DATA_SIZE(root) / 3) { /* push_leaf_left fixes the path. * make sure the path still points to our leaf * for possible call to del_ptr below -- GitLab From 36a516d953e02523e78ce27fbff91a968a9e5751 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Erik=20Andr=C3=A9n?= Date: Tue, 23 Jun 2009 12:22:48 -0300 Subject: [PATCH 0275/1342] V4L/DVB (12221): gspca - stv06xx-hdcs: Actually update the sensor state MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Signed-off-by: Erik Andrén Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c b/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c index 3039ec208f3..ec7f5536a8a 100644 --- a/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c +++ b/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c @@ -174,7 +174,9 @@ static int hdcs_set_state(struct sd *sd, enum hdcs_power_state state) } ret = stv06xx_write_sensor(sd, HDCS_REG_CONTROL(sd), val); - if (ret < 0) + + /* Update the state if the write succeeded */ + if (!ret) hdcs->state = state; return ret; -- GitLab From ac51295ccc0ff922fea62cfc6f72cddf9c6c7306 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Erik=20Andr=C3=A9n?= Date: Wed, 24 Jun 2009 04:30:56 -0300 Subject: [PATCH 0276/1342] V4L/DVB (12222): gspca - stv06xx-hdcs: Fix sensor sequence bug MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit All hdcs registers use bit 0 as a read/write flag and needs to be shifted one bit to the left. This wasn't accounted for when doing a sequence of writes. Signed-off-by: Erik Andrén Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) diff --git a/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c b/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c index ec7f5536a8a..a45171be3f8 100644 --- a/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c +++ b/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c @@ -131,9 +131,11 @@ static int hdcs_reg_write_seq(struct sd *sd, u8 reg, u8 *vals, u8 len) (reg + len > 0xff))) return -EINVAL; - for (i = 0; i < len; i++, reg++) { - regs[2*i] = reg; - regs[2*i+1] = vals[i]; + for (i = 0; i < len; i++) { + regs[2 * i] = reg; + regs[2 * i + 1] = vals[i]; + /* All addresses are shifted left one bit as bit 0 toggles r/w */ + reg += 2; } return stv06xx_write_sensor_bytes(sd, regs, len); -- GitLab From c0ea8f5b7264c813ee885f02b663ee3106f98afe Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Erik=20Andr=C3=A9n?= Date: Wed, 1 Jul 2009 02:56:44 -0300 Subject: [PATCH 0277/1342] V4L/DVB (12223): gspca - stv06xx-hdcs: Correct the pixelformat MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Signed-off-by: Erik Andrén Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c b/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c index a45171be3f8..e5024c8496e 100644 --- a/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c +++ b/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c @@ -64,7 +64,7 @@ static struct v4l2_pix_format hdcs1x00_mode[] = { { HDCS_1X00_DEF_WIDTH, HDCS_1X00_DEF_HEIGHT, - V4L2_PIX_FMT_SBGGR8, + V4L2_PIX_FMT_SGRBG8, V4L2_FIELD_NONE, .sizeimage = HDCS_1X00_DEF_WIDTH * HDCS_1X00_DEF_HEIGHT, @@ -80,7 +80,7 @@ static struct v4l2_pix_format hdcs1020_mode[] = { { HDCS_1020_DEF_WIDTH, HDCS_1020_DEF_HEIGHT, - V4L2_PIX_FMT_SBGGR8, + V4L2_PIX_FMT_SGRBG8, V4L2_FIELD_NONE, .sizeimage = HDCS_1020_DEF_WIDTH * HDCS_1020_DEF_HEIGHT, -- GitLab From 641f75caa874fffd679b64f850adee37103b0c0f Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Erik=20Andr=C3=A9n?= Date: Wed, 8 Jul 2009 14:47:16 -0300 Subject: [PATCH 0278/1342] V4L/DVB (12224): gspca - m5602-s5k4aa: Remove erroneous register writes MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit A couple of erroneous register writes snuck in that made the image go haywire. Remove these. Many thanks to Grégory Lardière for finding this out Signed-off-by: Erik Andrén Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/gspca/m5602/m5602_s5k4aa.c | 6 ------ 1 file changed, 6 deletions(-) diff --git a/drivers/media/video/gspca/m5602/m5602_s5k4aa.c b/drivers/media/video/gspca/m5602/m5602_s5k4aa.c index 191bcd71897..0163903d1c0 100644 --- a/drivers/media/video/gspca/m5602/m5602_s5k4aa.c +++ b/drivers/media/video/gspca/m5602/m5602_s5k4aa.c @@ -474,9 +474,6 @@ static int s5k4aa_set_vflip(struct gspca_dev *gspca_dev, __s32 val) PDEBUG(D_V4L2, "Set vertical flip to %d", val); err = m5602_write_sensor(sd, S5K4AA_PAGE_MAP, &data, 1); - if (err < 0) - return err; - err = m5602_write_sensor(sd, S5K4AA_READ_MODE, &data, 1); if (err < 0) return err; @@ -522,9 +519,6 @@ static int s5k4aa_set_hflip(struct gspca_dev *gspca_dev, __s32 val) PDEBUG(D_V4L2, "Set horizontal flip to %d", val); err = m5602_write_sensor(sd, S5K4AA_PAGE_MAP, &data, 1); - if (err < 0) - return err; - err = m5602_write_sensor(sd, S5K4AA_READ_MODE, &data, 1); if (err < 0) return err; -- GitLab From c43221df762c33e832e8855cae77989b6bf69fa6 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Sun, 12 Jul 2009 10:23:23 -0300 Subject: [PATCH 0279/1342] V4L/DVB (12233): em28xx: rename is_27xx to is_webcam Just renames the flag, to use a clearer name. Later patches will use this flag to properly set some drivers behaviors for webcams. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 4 ++-- drivers/media/video/em28xx/em28xx-core.c | 4 ++-- drivers/media/video/em28xx/em28xx-video.c | 4 ++-- drivers/media/video/em28xx/em28xx.h | 2 +- 4 files changed, 7 insertions(+), 7 deletions(-) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index ebd24a25fb8..8f869468280 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -450,7 +450,7 @@ struct em28xx_board em28xx_boards[] = { [EM2820_BOARD_SILVERCREST_WEBCAM] = { .name = "Silvercrest Webcam 1.3mpix", .tuner_type = TUNER_ABSENT, - .is_27xx = 1, + .is_webcam = 1, .decoder = EM28XX_MT9V011, .input = { { .type = EM28XX_VMUX_COMPOSITE1, @@ -1772,7 +1772,7 @@ void em28xx_pre_card_setup(struct em28xx *dev) em28xx_info("chip ID is em2750\n"); break; case CHIP_ID_EM2820: - if (dev->board.is_27xx) + if (dev->board.is_webcam) em28xx_info("chip is em2710\n"); else em28xx_info("chip ID is em2820\n"); diff --git a/drivers/media/video/em28xx/em28xx-core.c b/drivers/media/video/em28xx/em28xx-core.c index 079ab4d563a..8649bdb7eb9 100644 --- a/drivers/media/video/em28xx/em28xx-core.c +++ b/drivers/media/video/em28xx/em28xx-core.c @@ -652,7 +652,7 @@ int em28xx_set_outfmt(struct em28xx *dev) outfmt = dev->format->reg; - if (dev->board.is_27xx) { + if (dev->board.is_webcam) { vinmode = 0x0d; vinctl = 0x00; } else { @@ -707,7 +707,7 @@ static int em28xx_scaler_set(struct em28xx *dev, u16 h, u16 v) u8 mode; /* the em2800 scaler only supports scaling down to 50% */ - if (dev->board.is_27xx) { + if (dev->board.is_webcam) { /* FIXME: Don't use the scaler yet */ mode = 0; } else if (dev->board.is_em2800) { diff --git a/drivers/media/video/em28xx/em28xx-video.c b/drivers/media/video/em28xx/em28xx-video.c index 14316c91217..89ab2e3b9a2 100644 --- a/drivers/media/video/em28xx/em28xx-video.c +++ b/drivers/media/video/em28xx/em28xx-video.c @@ -726,7 +726,7 @@ static int vidioc_try_fmt_vid_cap(struct file *file, void *priv, return -EINVAL; } - if (dev->board.is_27xx) { + if (dev->board.is_webcam) { /* FIXME: This is the only supported fmt */ width = 640; height = 480; @@ -768,7 +768,7 @@ static int em28xx_set_video_format(struct em28xx *dev, unsigned int fourcc, struct em28xx_fmt *fmt; /* FIXME: This is the only supported fmt */ - if (dev->board.is_27xx) { + if (dev->board.is_webcam) { width = 640; height = 480; } diff --git a/drivers/media/video/em28xx/em28xx.h b/drivers/media/video/em28xx/em28xx.h index d90fef46376..dc92e9ef85a 100644 --- a/drivers/media/video/em28xx/em28xx.h +++ b/drivers/media/video/em28xx/em28xx.h @@ -390,7 +390,7 @@ struct em28xx_board { unsigned int max_range_640_480:1; unsigned int has_dvb:1; unsigned int has_snapshot_button:1; - unsigned int is_27xx:1; + unsigned int is_webcam:1; unsigned int valid:1; unsigned char xclk, i2c_speed; -- GitLab From 8a2e6990f44d4cebaafcc0af1a786912ae733bb2 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Sun, 12 Jul 2009 10:26:36 -0300 Subject: [PATCH 0280/1342] V4L/DVB (12234): em28xx-cards: use is_webcam flag for devices that are known to be webcams By having the webcam devices marked as such, it will help the em28xx driver to do the right thing on those devices. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 8f869468280..9e71f034665 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -207,7 +207,8 @@ struct em28xx_board em28xx_boards[] = { [EM2750_BOARD_UNKNOWN] = { .name = "Unknown EM2750/EM2751 webcam grabber", .xclk = EM28XX_XCLK_FREQUENCY_48MHZ, - .tuner_type = TUNER_ABSENT, /* This is a webcam */ + .tuner_type = TUNER_ABSENT, + .is_webcam = 1, .input = { { .type = EM28XX_VMUX_COMPOSITE1, .vmux = 0, @@ -239,7 +240,8 @@ struct em28xx_board em28xx_boards[] = { .name = "Huaqi DLCW-130", .valid = EM28XX_BOARD_NOT_VALIDATED, .xclk = EM28XX_XCLK_FREQUENCY_48MHZ, - .tuner_type = TUNER_ABSENT, /* This is a webcam */ + .tuner_type = TUNER_ABSENT, + .is_webcam = 1, .input = { { .type = EM28XX_VMUX_COMPOSITE1, .vmux = 0, @@ -440,7 +442,8 @@ struct em28xx_board em28xx_boards[] = { [EM2820_BOARD_VIDEOLOGY_20K14XUSB] = { .name = "Videology 20K14XUSB USB2.0", .valid = EM28XX_BOARD_NOT_VALIDATED, - .tuner_type = TUNER_ABSENT, /* This is a webcam */ + .tuner_type = TUNER_ABSENT, + .is_webcam = 1, .input = { { .type = EM28XX_VMUX_COMPOSITE1, .vmux = 0, @@ -500,7 +503,8 @@ struct em28xx_board em28xx_boards[] = { /* Beijing Huaqi Information Digital Technology Co., Ltd */ .name = "NetGMBH Cam", .valid = EM28XX_BOARD_NOT_VALIDATED, - .tuner_type = TUNER_ABSENT, /* This is a webcam */ + .tuner_type = TUNER_ABSENT, + .is_webcam = 1, .input = { { .type = EM28XX_VMUX_COMPOSITE1, .vmux = 0, -- GitLab From 8b220793d6fd309176438721088515be893630cd Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Sun, 12 Jul 2009 10:56:21 -0300 Subject: [PATCH 0281/1342] V4L/DVB (12235): em28xx: detects sensors also with the generic em2750/2750 entry Webcams in general don't have eeprom. So, the sensor hint code should be called to properly detect what sensor is inside. Signed-off-by: Mauro Carvalho Chehab --- Documentation/video4linux/CARDLIST.em28xx | 2 +- drivers/media/video/em28xx/em28xx-cards.c | 9 +++++---- 2 files changed, 6 insertions(+), 5 deletions(-) diff --git a/Documentation/video4linux/CARDLIST.em28xx b/Documentation/video4linux/CARDLIST.em28xx index 014d255231f..68c236c0184 100644 --- a/Documentation/video4linux/CARDLIST.em28xx +++ b/Documentation/video4linux/CARDLIST.em28xx @@ -20,7 +20,7 @@ 19 -> EM2860/SAA711X Reference Design (em2860) 20 -> AMD ATI TV Wonder HD 600 (em2880) [0438:b002] 21 -> eMPIA Technology, Inc. GrabBeeX+ Video Encoder (em2800) [eb1a:2801] - 22 -> Unknown EM2750/EM2751 webcam grabber (em2750) [eb1a:2750,eb1a:2751] + 22 -> EM2710/EM2750/EM2751 webcam grabber (em2750) [eb1a:2750,eb1a:2751] 23 -> Huaqi DLCW-130 (em2750) 24 -> D-Link DUB-T210 TV Tuner (em2820/em2840) [2001:f112] 25 -> Gadmei UTV310 (em2820/em2840) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 9e71f034665..e64e1242a1b 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -205,7 +205,7 @@ static struct em28xx_reg_seq silvercrest_reg_seq[] = { */ struct em28xx_board em28xx_boards[] = { [EM2750_BOARD_UNKNOWN] = { - .name = "Unknown EM2750/EM2751 webcam grabber", + .name = "EM2710/EM2750/EM2751 webcam grabber", .xclk = EM28XX_XCLK_FREQUENCY_48MHZ, .tuner_type = TUNER_ABSENT, .is_webcam = 1, @@ -1720,7 +1720,8 @@ static int em28xx_hint_sensor(struct em28xx *dev) __be16 version_be; u16 version; - if (dev->model != EM2820_BOARD_UNKNOWN) + if (dev->model != EM2820_BOARD_UNKNOWN && + dev->model != EM2750_BOARD_UNKNOWN) return 0; dev->i2c_client.addr = 0xba >> 1; @@ -1738,11 +1739,11 @@ static int em28xx_hint_sensor(struct em28xx *dev) sensor_name = "mt9v011"; break; default: - printk("Unknown Sensor 0x%04x\n", be16_to_cpu(version)); + printk("Unknown Micron Sensor 0x%04x\n", be16_to_cpu(version)); return -EINVAL; } - em28xx_errdev("Sensor is %s, assuming that webcam is %s\n", + em28xx_errdev("Sensor is %s, using model %s entry.\n", sensor_name, em28xx_boards[dev->model].name); return 0; -- GitLab From 527f09a981e398331c2f8d8f7af83cd46e6a06cc Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Sun, 12 Jul 2009 11:04:15 -0300 Subject: [PATCH 0282/1342] V4L/DVB (12236): em28xx: stop abusing of board->decoder for sensor information Instead of using em28xx board decoder field for storing sensor information, let's use instead a separate field for it. Also, as sensors are currently autodetected, there's no need of having it at the boards description. So, move it to the main em28xx struct. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 4 ++-- drivers/media/video/em28xx/em28xx.h | 8 +++++++- 2 files changed, 9 insertions(+), 3 deletions(-) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index e64e1242a1b..530170ae016 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -454,7 +454,6 @@ struct em28xx_board em28xx_boards[] = { .name = "Silvercrest Webcam 1.3mpix", .tuner_type = TUNER_ABSENT, .is_webcam = 1, - .decoder = EM28XX_MT9V011, .input = { { .type = EM28XX_VMUX_COMPOSITE1, .vmux = 0, @@ -1737,6 +1736,7 @@ static int em28xx_hint_sensor(struct em28xx *dev) case MT9V011_VERSION: dev->model = EM2820_BOARD_SILVERCREST_WEBCAM; sensor_name = "mt9v011"; + dev->em28xx_sensor = EM28XX_MT9V011; break; default: printk("Unknown Micron Sensor 0x%04x\n", be16_to_cpu(version)); @@ -2267,7 +2267,7 @@ void em28xx_card_setup(struct em28xx *dev) v4l2_i2c_new_probed_subdev(&dev->v4l2_dev, &dev->i2c_adap, "tvp5150", "tvp5150", tvp5150_addrs); - if (dev->board.decoder == EM28XX_MT9V011) + if (dev->em28xx_sensor == EM28XX_MT9V011) v4l2_i2c_new_probed_subdev(&dev->v4l2_dev, &dev->i2c_adap, "mt9v011", "mt9v011", mt9v011_addrs); diff --git a/drivers/media/video/em28xx/em28xx.h b/drivers/media/video/em28xx/em28xx.h index dc92e9ef85a..655dd78cc07 100644 --- a/drivers/media/video/em28xx/em28xx.h +++ b/drivers/media/video/em28xx/em28xx.h @@ -358,9 +358,13 @@ struct em28xx_input { #define INPUT(nr) (&em28xx_boards[dev->model].input[nr]) enum em28xx_decoder { - EM28XX_NODECODER, + EM28XX_NODECODER = 0, EM28XX_TVP5150, EM28XX_SAA711X, +}; + +enum em28xx_sensor { + EM28XX_NOSENSOR = 0, EM28XX_MT9V011, }; @@ -474,6 +478,8 @@ struct em28xx { struct v4l2_device v4l2_dev; struct em28xx_board board; + enum em28xx_sensor em28xx_sensor; + unsigned int stream_on:1; /* Locks streams */ unsigned int has_audio_class:1; unsigned int has_alsa_audio:1; -- GitLab From 9873740b2f41b37ec074afd4b8910b87dbebc0db Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Mon, 13 Jul 2009 01:03:37 -0300 Subject: [PATCH 0283/1342] V4L/DVB (12237): mt9v011: implement VIDIOC_QUERYCTRL Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/mt9v011.c | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) diff --git a/drivers/media/video/mt9v011.c b/drivers/media/video/mt9v011.c index 1fe8fc9183a..241382f5ba2 100644 --- a/drivers/media/video/mt9v011.c +++ b/drivers/media/video/mt9v011.c @@ -215,6 +215,23 @@ static int mt9v011_g_ctrl(struct v4l2_subdev *sd, struct v4l2_control *ctrl) return -EINVAL; } +static int mt9v011_queryctrl(struct v4l2_subdev *sd, struct v4l2_queryctrl *qc) +{ + int i; + + v4l2_dbg(1, debug, sd, "queryctrl called\n"); + + for (i = 0; i < ARRAY_SIZE(mt9v011_qctrl); i++) + if (qc->id && qc->id == mt9v011_qctrl[i].id) { + memcpy(qc, &(mt9v011_qctrl[i]), + sizeof(*qc)); + return 0; + } + + return -EINVAL; +} + + static int mt9v011_s_ctrl(struct v4l2_subdev *sd, struct v4l2_control *ctrl) { struct mt9v011 *core = to_mt9v011(sd); @@ -338,6 +355,7 @@ static int mt9v011_g_chip_ident(struct v4l2_subdev *sd, } static const struct v4l2_subdev_core_ops mt9v011_core_ops = { + .queryctrl = mt9v011_queryctrl, .g_ctrl = mt9v011_g_ctrl, .s_ctrl = mt9v011_s_ctrl, .reset = mt9v011_reset, -- GitLab From b04fb6615285d18df34ffd6cdd51db7a8a78dda0 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Mon, 13 Jul 2009 01:28:21 -0300 Subject: [PATCH 0284/1342] V4L/DVB (12238): em28xx: call sensor detection code for all webcam entries With the previous approach, autodetection were working only for the two generic entries (em275x and em2820 unknown ones). So, if someone would try to force probing an specific device, the code would not properly run the autodetection code. With the new approach, the sensor autodetection will be run not only for the two generic entries, but also do webcam specific ones. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 530170ae016..1318766b35b 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -234,6 +234,7 @@ struct em28xx_board em28xx_boards[] = { [EM2820_BOARD_UNKNOWN] = { .name = "Unknown EM2750/28xx video grabber", .tuner_type = TUNER_ABSENT, + .is_webcam = 1, /* To enable sensor probe */ }, [EM2750_BOARD_DLCW_130] = { /* Beijing Huaqi Information Digital Technology Co., Ltd */ @@ -1719,10 +1720,6 @@ static int em28xx_hint_sensor(struct em28xx *dev) __be16 version_be; u16 version; - if (dev->model != EM2820_BOARD_UNKNOWN && - dev->model != EM2750_BOARD_UNKNOWN) - return 0; - dev->i2c_client.addr = 0xba >> 1; cmd = 0; i2c_master_send(&dev->i2c_client, &cmd, 1); @@ -1777,10 +1774,7 @@ void em28xx_pre_card_setup(struct em28xx *dev) em28xx_info("chip ID is em2750\n"); break; case CHIP_ID_EM2820: - if (dev->board.is_webcam) - em28xx_info("chip is em2710\n"); - else - em28xx_info("chip ID is em2820\n"); + em28xx_info("chip ID is em2710 or em2820\n"); break; case CHIP_ID_EM2840: em28xx_info("chip ID is em2840\n"); @@ -2415,7 +2409,13 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev, return errCode; } - em28xx_hint_sensor(dev); + /* + * If the device can be a webcam, seek for a sensor. + * If sensor is not found, then it isn't a webcam. + */ + if (dev->board.is_webcam) + if (em28xx_hint_sensor(dev) < 0) + dev->board.is_webcam = 0; /* Do board specific init and eeprom reading */ em28xx_card_setup(dev); -- GitLab From 5569996421fa1cfc1fc0d9e683ac1def46ea985d Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Mon, 13 Jul 2009 20:15:02 -0300 Subject: [PATCH 0285/1342] V4L/DVB (12239): em28xx: fix webcam scaling While trying to fix an mt9v001 webcam, I noticed that HSCALE/VSCALE do work with em28xx + webcam. The issue is that the scaling setup depends on the number of visible rows/cols of the input image. With mt9v011 (Silvercrest), the resolution is 640x480. So, the scaling is different from a normal TV image (720x480 on NTSC). This were causing a wrong scaling and a previous patch disabled scaling. As each sensor have their different resolution setting, the xres/yres should be adjusted accordingly with the input sensor. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 6 +++--- drivers/media/video/em28xx/em28xx-core.c | 5 +---- drivers/media/video/em28xx/em28xx-video.c | 16 +++------------- drivers/media/video/em28xx/em28xx.h | 15 +++++++++++---- 4 files changed, 18 insertions(+), 24 deletions(-) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 1318766b35b..d4a7e6075cc 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -58,8 +58,6 @@ static unsigned int card[] = {[0 ... (EM28XX_MAXBOARDS - 1)] = UNSET }; module_param_array(card, int, NULL, 0444); MODULE_PARM_DESC(card, "card type"); -#define MT9V011_VERSION 0x8243 - /* Bitmask marking allocated devices from 0 to EM28XX_MAXBOARDS */ static unsigned long em28xx_devused; @@ -1730,10 +1728,12 @@ static int em28xx_hint_sensor(struct em28xx *dev) version = be16_to_cpu(version_be); switch (version) { - case MT9V011_VERSION: + case 0x8243: /* mt9v011 640x480 1.3 Mpix sensor */ dev->model = EM2820_BOARD_SILVERCREST_WEBCAM; sensor_name = "mt9v011"; dev->em28xx_sensor = EM28XX_MT9V011; + dev->sensor_xres = 640; + dev->sensor_yres = 480; break; default: printk("Unknown Micron Sensor 0x%04x\n", be16_to_cpu(version)); diff --git a/drivers/media/video/em28xx/em28xx-core.c b/drivers/media/video/em28xx/em28xx-core.c index 8649bdb7eb9..c7fcce71394 100644 --- a/drivers/media/video/em28xx/em28xx-core.c +++ b/drivers/media/video/em28xx/em28xx-core.c @@ -707,10 +707,7 @@ static int em28xx_scaler_set(struct em28xx *dev, u16 h, u16 v) u8 mode; /* the em2800 scaler only supports scaling down to 50% */ - if (dev->board.is_webcam) { - /* FIXME: Don't use the scaler yet */ - mode = 0; - } else if (dev->board.is_em2800) { + if (dev->board.is_em2800) { mode = (v ? 0x20 : 0x00) | (h ? 0x10 : 0x00); } else { u8 buf[2]; diff --git a/drivers/media/video/em28xx/em28xx-video.c b/drivers/media/video/em28xx/em28xx-video.c index 89ab2e3b9a2..ff37b4c15f4 100644 --- a/drivers/media/video/em28xx/em28xx-video.c +++ b/drivers/media/video/em28xx/em28xx-video.c @@ -657,8 +657,8 @@ static void get_scale(struct em28xx *dev, unsigned int width, unsigned int height, unsigned int *hscale, unsigned int *vscale) { - unsigned int maxw = norm_maxw(dev); - unsigned int maxh = norm_maxh(dev); + unsigned int maxw = norm_maxw(dev); + unsigned int maxh = norm_maxh(dev); *hscale = (((unsigned long)maxw) << 12) / width - 4096L; if (*hscale >= 0x4000) @@ -726,11 +726,7 @@ static int vidioc_try_fmt_vid_cap(struct file *file, void *priv, return -EINVAL; } - if (dev->board.is_webcam) { - /* FIXME: This is the only supported fmt */ - width = 640; - height = 480; - } else if (dev->board.is_em2800) { + if (dev->board.is_em2800) { /* the em2800 can only scale down to 50% */ height = height > (3 * maxh / 4) ? maxh : maxh / 2; width = width > (3 * maxw / 4) ? maxw : maxw / 2; @@ -767,12 +763,6 @@ static int em28xx_set_video_format(struct em28xx *dev, unsigned int fourcc, { struct em28xx_fmt *fmt; - /* FIXME: This is the only supported fmt */ - if (dev->board.is_webcam) { - width = 640; - height = 480; - } - fmt = format_by_fourcc(fourcc); if (!fmt) return -EINVAL; diff --git a/drivers/media/video/em28xx/em28xx.h b/drivers/media/video/em28xx/em28xx.h index 655dd78cc07..71444ddbe40 100644 --- a/drivers/media/video/em28xx/em28xx.h +++ b/drivers/media/video/em28xx/em28xx.h @@ -479,6 +479,7 @@ struct em28xx { struct em28xx_board board; enum em28xx_sensor em28xx_sensor; + int sensor_xres, sensor_yres; unsigned int stream_on:1; /* Locks streams */ unsigned int has_audio_class:1; @@ -760,17 +761,23 @@ static inline int em28xx_gamma_set(struct em28xx *dev, s32 val) /*FIXME: maxw should be dependent of alt mode */ static inline unsigned int norm_maxw(struct em28xx *dev) { + if (dev->board.is_webcam) + return dev->sensor_xres; + if (dev->board.max_range_640_480) return 640; - else - return 720; + + return 720; } static inline unsigned int norm_maxh(struct em28xx *dev) { + if (dev->board.is_webcam) + return dev->sensor_yres; + if (dev->board.max_range_640_480) return 480; - else - return (dev->norm & V4L2_STD_625_50) ? 576 : 480; + + return (dev->norm & V4L2_STD_625_50) ? 576 : 480; } #endif -- GitLab From e11206e67f738b04d0c508795adc9bff504bc875 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Tue, 14 Jul 2009 02:38:18 -0300 Subject: [PATCH 0286/1342] V4L/DVB (12240): mt9v011: add a function to calculate frames per second rate It is possible to adjust the fps rate by changing some register values. This is function of the connected Xtal at the camera sensor, being a 27 MHz cristal needed, in order to support 640x480 at 30 fps. For now, it will only calculate the values for fps. Later patches may introduce V4L2 ioctls, to allow frequency rate adjustments. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/mt9v011.c | 32 +++++++++++++++++++++++++++++++- 1 file changed, 31 insertions(+), 1 deletion(-) diff --git a/drivers/media/video/mt9v011.c b/drivers/media/video/mt9v011.c index 241382f5ba2..f7b5279a7d5 100644 --- a/drivers/media/video/mt9v011.c +++ b/drivers/media/video/mt9v011.c @@ -8,6 +8,7 @@ #include #include #include +#include #include #include "mt9v011.h" #include @@ -57,6 +58,7 @@ static struct v4l2_queryctrl mt9v011_qctrl[] = { struct mt9v011 { struct v4l2_subdev sd; unsigned width, height; + unsigned xtal; u16 global_gain, red_bal, blue_bal; }; @@ -131,7 +133,7 @@ static const struct i2c_reg_value mt9v011_init_default[] = { { R1E_MT9V011_DIGITAL_ZOOM, 0x0000 }, { R20_MT9V011_READ_MODE, 0x1000 }, - { R07_MT9V011_OUT_CTRL, 0x000a }, /* chip enable */ + { R07_MT9V011_OUT_CTRL, 0x0002 }, /* chip enable */ }; static void set_balance(struct v4l2_subdev *sd) @@ -154,6 +156,31 @@ static void set_balance(struct v4l2_subdev *sd) mt9v011_write(sd, R2D_MT9V011_RED_GAIN, red_gain); } +static void calc_fps(struct v4l2_subdev *sd) +{ + struct mt9v011 *core = to_mt9v011(sd); + unsigned height, width, hblank, vblank, speed; + unsigned row_time, t_time; + u64 frames_per_ms; + unsigned tmp; + + height = mt9v011_read(sd, R03_MT9V011_HEIGHT); + width = mt9v011_read(sd, R04_MT9V011_WIDTH); + hblank = mt9v011_read(sd, R05_MT9V011_HBLANK); + vblank = mt9v011_read(sd, R06_MT9V011_VBLANK); + speed = mt9v011_read(sd, R0A_MT9V011_CLK_SPEED); + + row_time = (width + 113 + hblank) * (speed + 2); + t_time = row_time * (height + vblank + 1); + + frames_per_ms = core->xtal * 1000l; + do_div(frames_per_ms, t_time); + tmp = frames_per_ms; + + v4l2_dbg(1, debug, sd, "Programmed to %u.%03u fps (%d pixel clcks)\n", + tmp / 1000, tmp % 1000, t_time); +} + static void set_res(struct v4l2_subdev *sd) { struct mt9v011 *core = to_mt9v011(sd); @@ -179,6 +206,8 @@ static void set_res(struct v4l2_subdev *sd) mt9v011_write(sd, R01_MT9V011_ROWSTART, vstart); mt9v011_write(sd, R03_MT9V011_HEIGHT, core->height); mt9v011_write(sd, R06_MT9V011_VBLANK, 508 - core->height); + + calc_fps(sd); }; static int mt9v011_reset(struct v4l2_subdev *sd, u32 val) @@ -413,6 +442,7 @@ static int mt9v011_probe(struct i2c_client *c, core->global_gain = 0x0024; core->width = 640; core->height = 480; + core->xtal = 27000000; /* Hz */ v4l_info(c, "chip found @ 0x%02x (%s)\n", c->addr << 1, c->adapter->name); -- GitLab From c180604a87c5abb0a117998009d01a4499d58653 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Tue, 14 Jul 2009 02:39:19 -0300 Subject: [PATCH 0287/1342] V4L/DVB (12241): mt9v011: Fix vstart vstart calculus were wrong. Fix it. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/mt9v011.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/media/video/mt9v011.c b/drivers/media/video/mt9v011.c index f7b5279a7d5..d7b15dd836e 100644 --- a/drivers/media/video/mt9v011.c +++ b/drivers/media/video/mt9v011.c @@ -202,7 +202,7 @@ static void set_res(struct v4l2_subdev *sd) mt9v011_write(sd, R04_MT9V011_WIDTH, core->width); mt9v011_write(sd, R05_MT9V011_HBLANK, 771 - core->width); - vstart = 8 + (640 - core->height) / 2; + vstart = 8 + (480 - core->height) / 2; mt9v011_write(sd, R01_MT9V011_ROWSTART, vstart); mt9v011_write(sd, R03_MT9V011_HEIGHT, core->height); mt9v011_write(sd, R06_MT9V011_VBLANK, 508 - core->height); -- GitLab From 2ea472ff704a8a94b3b9abec438db23e512be337 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Tue, 14 Jul 2009 03:14:21 -0300 Subject: [PATCH 0288/1342] V4L/DVB (12242): mt9v011: implement core->s_config to allow adjusting xtal frequency Since frames per second is a function of cristal frequency, and this is device-specific, add a function that allows adjusting it, via subdev->core->s_config callback. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/mt9v011.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) diff --git a/drivers/media/video/mt9v011.c b/drivers/media/video/mt9v011.c index d7b15dd836e..b2260de645f 100644 --- a/drivers/media/video/mt9v011.c +++ b/drivers/media/video/mt9v011.c @@ -340,6 +340,22 @@ static int mt9v011_s_fmt(struct v4l2_subdev *sd, struct v4l2_format *fmt) return 0; } +static int mt9v011_s_config(struct v4l2_subdev *sd, int dumb, void *data) +{ + struct mt9v011 *core = to_mt9v011(sd); + unsigned *xtal = data; + + v4l2_dbg(1, debug, sd, "s_config called\n"); + + if (xtal) { + core->xtal = *xtal; + v4l2_dbg(1, debug, sd, "xtal set to %d.%03d MHz\n", + *xtal / 1000000, (*xtal / 1000) % 1000); + } + + return 0; +} + #ifdef CONFIG_VIDEO_ADV_DEBUG static int mt9v011_g_register(struct v4l2_subdev *sd, @@ -388,6 +404,7 @@ static const struct v4l2_subdev_core_ops mt9v011_core_ops = { .g_ctrl = mt9v011_g_ctrl, .s_ctrl = mt9v011_s_ctrl, .reset = mt9v011_reset, + .s_config = mt9v011_s_config, .g_chip_ident = mt9v011_g_chip_ident, #ifdef CONFIG_VIDEO_ADV_DEBUG .g_register = mt9v011_g_register, -- GitLab From d36bb4e77257ed0df86deca3f69794f037f68c7d Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Tue, 14 Jul 2009 03:18:39 -0300 Subject: [PATCH 0289/1342] V4L/DVB (12243): em28xx: allow specifying sensor xtal frequency In order to properly estimate fps, mt9v011 sensor driver needs to know what is the used frequency on the sensor cristal. Adds the proper fields and initialization code for specifying the cristal frequency. Also, based on experimentation, it was noticed that the Silvercrest is outputing data at 7 fps. This means that it should be using a 6.3 MHz cristal. This information needs to be double checked later, by opening the device. Anyway, by using this value for xtal, at least now we have the correct fps report. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 11 ++++++++--- drivers/media/video/em28xx/em28xx.h | 2 ++ 2 files changed, 10 insertions(+), 3 deletions(-) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index d4a7e6075cc..82536dd6b0f 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -1734,6 +1734,7 @@ static int em28xx_hint_sensor(struct em28xx *dev) dev->em28xx_sensor = EM28XX_MT9V011; dev->sensor_xres = 640; dev->sensor_yres = 480; + dev->sensor_xtal = 6300000; break; default: printk("Unknown Micron Sensor 0x%04x\n", be16_to_cpu(version)); @@ -2261,9 +2262,13 @@ void em28xx_card_setup(struct em28xx *dev) v4l2_i2c_new_probed_subdev(&dev->v4l2_dev, &dev->i2c_adap, "tvp5150", "tvp5150", tvp5150_addrs); - if (dev->em28xx_sensor == EM28XX_MT9V011) - v4l2_i2c_new_probed_subdev(&dev->v4l2_dev, &dev->i2c_adap, - "mt9v011", "mt9v011", mt9v011_addrs); + if (dev->em28xx_sensor == EM28XX_MT9V011) { + struct v4l2_subdev *sd; + + sd = v4l2_i2c_new_probed_subdev(&dev->v4l2_dev, + &dev->i2c_adap, "mt9v011", "mt9v011", mt9v011_addrs); + v4l2_subdev_call(sd, core, s_config, 0, &dev->sensor_xtal); + } if (dev->board.adecoder == EM28XX_TVAUDIO) v4l2_i2c_new_subdev(&dev->v4l2_dev, &dev->i2c_adap, diff --git a/drivers/media/video/em28xx/em28xx.h b/drivers/media/video/em28xx/em28xx.h index 71444ddbe40..ce76633786c 100644 --- a/drivers/media/video/em28xx/em28xx.h +++ b/drivers/media/video/em28xx/em28xx.h @@ -478,8 +478,10 @@ struct em28xx { struct v4l2_device v4l2_dev; struct em28xx_board board; + /* Webcam specific fields */ enum em28xx_sensor em28xx_sensor; int sensor_xres, sensor_yres; + int sensor_xtal; unsigned int stream_on:1; /* Locks streams */ unsigned int has_audio_class:1; -- GitLab From 579d315218e8a3f696e375c5f6917da6488bec8a Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Tue, 14 Jul 2009 12:33:25 -0300 Subject: [PATCH 0290/1342] V4L/DVB (12244): em28xx: adjust vinmode/vinctl based on the stream input format Depending on the video input format, vinmode/vinctl needs adjustments. For TV, this is not relevant, since the supported decoders output data at the same format. However, webcam sensors may have different formats, so, this needs to be adjusted based on the device. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 11 +++++++++++ drivers/media/video/em28xx/em28xx-core.c | 17 +++-------------- drivers/media/video/em28xx/em28xx.h | 3 +++ 3 files changed, 17 insertions(+), 14 deletions(-) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 82536dd6b0f..e793aee1672 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -1735,6 +1735,11 @@ static int em28xx_hint_sensor(struct em28xx *dev) dev->sensor_xres = 640; dev->sensor_yres = 480; dev->sensor_xtal = 6300000; + + /* probably means GRGB 16 bit bayer */ + dev->vinmode = 0x0d; + dev->vinctl = 0x00; + break; default: printk("Unknown Micron Sensor 0x%04x\n", be16_to_cpu(version)); @@ -2414,6 +2419,12 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev, return errCode; } + /* + * Default format, used for tvp5150 or saa711x output formats + */ + dev->vinmode = 0x10; + dev->vinctl = 0x11; + /* * If the device can be a webcam, seek for a sensor. * If sensor is not found, then it isn't a webcam. diff --git a/drivers/media/video/em28xx/em28xx-core.c b/drivers/media/video/em28xx/em28xx-core.c index c7fcce71394..5b78e199abd 100644 --- a/drivers/media/video/em28xx/em28xx-core.c +++ b/drivers/media/video/em28xx/em28xx-core.c @@ -648,28 +648,17 @@ int em28xx_capture_start(struct em28xx *dev, int start) int em28xx_set_outfmt(struct em28xx *dev) { int ret; - int vinmode, vinctl, outfmt; - - outfmt = dev->format->reg; - - if (dev->board.is_webcam) { - vinmode = 0x0d; - vinctl = 0x00; - } else { - vinmode = 0x10; - vinctl = 0x11; - } ret = em28xx_write_reg_bits(dev, EM28XX_R27_OUTFMT, - outfmt | 0x20, 0xff); + dev->format->reg | 0x20, 0xff); if (ret < 0) return ret; - ret = em28xx_write_reg(dev, EM28XX_R10_VINMODE, vinmode); + ret = em28xx_write_reg(dev, EM28XX_R10_VINMODE, dev->vinmode); if (ret < 0) return ret; - return em28xx_write_reg(dev, EM28XX_R11_VINCTRL, vinctl); + return em28xx_write_reg(dev, EM28XX_R11_VINCTRL, dev->vinctl); } static int em28xx_accumulator_set(struct em28xx *dev, u8 xmin, u8 xmax, diff --git a/drivers/media/video/em28xx/em28xx.h b/drivers/media/video/em28xx/em28xx.h index ce76633786c..766ab59b8d5 100644 --- a/drivers/media/video/em28xx/em28xx.h +++ b/drivers/media/video/em28xx/em28xx.h @@ -483,6 +483,9 @@ struct em28xx { int sensor_xres, sensor_yres; int sensor_xtal; + /* Vinmode/Vinctl used at the driver */ + int vinmode, vinctl; + unsigned int stream_on:1; /* Locks streams */ unsigned int has_audio_class:1; unsigned int has_alsa_audio:1; -- GitLab From b80fd2d811b48a92051f86d257b00f373e69a6d7 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Tue, 14 Jul 2009 21:08:22 -0300 Subject: [PATCH 0291/1342] V4L/DVB (12245): em28xx: add support for mt9m001 webcams Thanks to Wally for bringing the issue and helping with the tests. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 41 +++++++++++++++++++++++ drivers/media/video/em28xx/em28xx.h | 1 + 2 files changed, 42 insertions(+) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index e793aee1672..1bd789a52e6 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -211,6 +211,7 @@ struct em28xx_board em28xx_boards[] = { .type = EM28XX_VMUX_COMPOSITE1, .vmux = 0, .amux = EM28XX_AMUX_VIDEO, + .gpio = silvercrest_reg_seq, } }, }, [EM2800_BOARD_UNKNOWN] = { @@ -1706,6 +1707,32 @@ static inline void em28xx_set_model(struct em28xx *dev) EM28XX_I2C_FREQ_100_KHZ; } +/* FIXME: Should be replaced by a proper mt9m001 driver */ +static int em28xx_initialize_mt9m001(struct em28xx *dev) +{ + int i; + unsigned char regs[][3] = { + { 0x0d, 0x00, 0x01, }, + { 0x0d, 0x00, 0x00, }, + { 0x04, 0x05, 0x00, }, /* hres = 1280 */ + { 0x03, 0x04, 0x00, }, /* vres = 1024 */ + { 0x20, 0x11, 0x00, }, + { 0x06, 0x00, 0x10, }, + { 0x2b, 0x00, 0x24, }, + { 0x2e, 0x00, 0x24, }, + { 0x35, 0x00, 0x24, }, + { 0x2d, 0x00, 0x20, }, + { 0x2c, 0x00, 0x20, }, + { 0x09, 0x0a, 0xd4, }, + { 0x35, 0x00, 0x57, }, + }; + + for (i = 0; i < ARRAY_SIZE(regs); i++) + i2c_master_send(&dev->i2c_client, ®s[i][0], 3); + + return 0; +} + /* HINT method: webcam I2C chips * * This method work for webcams with Micron sensors @@ -1740,6 +1767,19 @@ static int em28xx_hint_sensor(struct em28xx *dev) dev->vinmode = 0x0d; dev->vinctl = 0x00; + break; + case 0x8431: + dev->model = EM2750_BOARD_UNKNOWN; + sensor_name = "mt9m001"; + dev->em28xx_sensor = EM28XX_MT9M001; + em28xx_initialize_mt9m001(dev); + dev->sensor_xres = 1280; + dev->sensor_yres = 1024; + + /* probably means BGGR 16 bit bayer */ + dev->vinmode = 0x0c; + dev->vinctl = 0x00; + break; default: printk("Unknown Micron Sensor 0x%04x\n", be16_to_cpu(version)); @@ -2275,6 +2315,7 @@ void em28xx_card_setup(struct em28xx *dev) v4l2_subdev_call(sd, core, s_config, 0, &dev->sensor_xtal); } + if (dev->board.adecoder == EM28XX_TVAUDIO) v4l2_i2c_new_subdev(&dev->v4l2_dev, &dev->i2c_adap, "tvaudio", "tvaudio", dev->board.tvaudio_addr); diff --git a/drivers/media/video/em28xx/em28xx.h b/drivers/media/video/em28xx/em28xx.h index 766ab59b8d5..45bd513f62d 100644 --- a/drivers/media/video/em28xx/em28xx.h +++ b/drivers/media/video/em28xx/em28xx.h @@ -366,6 +366,7 @@ enum em28xx_decoder { enum em28xx_sensor { EM28XX_NOSENSOR = 0, EM28XX_MT9V011, + EM28XX_MT9M001, }; enum em28xx_adecoder { -- GitLab From 4fb202a8d9d936f7080ab631140b447a0625e36c Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Sun, 12 Jul 2009 17:51:12 -0300 Subject: [PATCH 0292/1342] V4L/DVB (12257): em28xx: make tuning work for Terratec Cinergy T XS USB (mt352 variant) The Terratec Cinergy T XS USB can have either a zl10353 or an mt352. Add support for the MT352 variant. Thanks to Jelle de Jong for providing a unit to test/debug with. Cc: Jelle de Jong Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-dvb.c | 47 +++++++++++++++++++++---- 1 file changed, 41 insertions(+), 6 deletions(-) diff --git a/drivers/media/video/em28xx/em28xx-dvb.c b/drivers/media/video/em28xx/em28xx-dvb.c index 3da97c32b8f..d57f7583ac6 100644 --- a/drivers/media/video/em28xx/em28xx-dvb.c +++ b/drivers/media/video/em28xx/em28xx-dvb.c @@ -31,6 +31,8 @@ #include "lgdt330x.h" #include "zl10353.h" #include "s5h1409.h" +#include "mt352.h" +#include "mt352_priv.h" /* FIXME */ MODULE_DESCRIPTION("driver for em28xx based DVB cards"); MODULE_AUTHOR("Mauro Carvalho Chehab "); @@ -258,6 +260,41 @@ static struct drx397xD_config em28xx_drx397xD_with_xc3028 = { }; #endif +static int mt352_terratec_xs_init(struct dvb_frontend *fe) +{ + /* Values extracted from a USB trace of the Terratec Windows driver */ + static u8 clock_config[] = { CLOCK_CTL, 0x38, 0x2c }; + static u8 reset[] = { RESET, 0x80 }; + static u8 adc_ctl_1_cfg[] = { ADC_CTL_1, 0x40 }; + static u8 agc_cfg[] = { AGC_TARGET, 0x28, 0xa0 }; + static u8 input_freq_cfg[] = { INPUT_FREQ_1, 0x31, 0xb8 }; + static u8 rs_err_cfg[] = { RS_ERR_PER_1, 0x00, 0x4d }; + static u8 capt_range_cfg[] = { CAPT_RANGE, 0x32 }; + static u8 trl_nom_cfg[] = { TRL_NOMINAL_RATE_1, 0x64, 0x00 }; + static u8 tps_given_cfg[] = { TPS_GIVEN_1, 0x40, 0x80, 0x50 }; + static u8 tuner_go[] = { TUNER_GO, 0x5d}; + + mt352_write(fe, clock_config, sizeof(clock_config)); + udelay(200); + mt352_write(fe, reset, sizeof(reset)); + mt352_write(fe, adc_ctl_1_cfg, sizeof(adc_ctl_1_cfg)); + mt352_write(fe, agc_cfg, sizeof(agc_cfg)); + mt352_write(fe, input_freq_cfg, sizeof(input_freq_cfg)); + mt352_write(fe, rs_err_cfg, sizeof(rs_err_cfg)); + mt352_write(fe, capt_range_cfg, sizeof(capt_range_cfg)); + mt352_write(fe, trl_nom_cfg, sizeof(trl_nom_cfg)); + mt352_write(fe, tps_given_cfg, sizeof(tps_given_cfg)); + mt352_write(fe, tuner_go, sizeof(tuner_go)); + return 0; +} + +static struct mt352_config terratec_xs_mt352_cfg = { + .demod_address = (0x1e >> 1), + .no_tuner = 1, + .if2 = 45600, + .demod_init = mt352_terratec_xs_init, +}; + /* ------------------------------------------------------------------ */ static int attach_xc3028(u8 addr, struct em28xx *dev) @@ -458,13 +495,11 @@ static int dvb_init(struct em28xx *dev) if (dvb->frontend == NULL) { /* This board could have either a zl10353 or a mt352. If the chip id isn't for zl10353, try mt352 */ - - /* FIXME: make support for mt352 work */ - printk(KERN_ERR "version of this board with mt352 not " - "currently supported\n"); - result = -EINVAL; - goto out_free; + dvb->frontend = dvb_attach(mt352_attach, + &terratec_xs_mt352_cfg, + &dev->i2c_adap); } + if (attach_xc3028(0x61, dev) < 0) { result = -EINVAL; goto out_free; -- GitLab From ff69786b4ccd0d5b99a60ba0be98237f9b7d8f52 Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Sun, 12 Jul 2009 18:44:19 -0300 Subject: [PATCH 0293/1342] V4L/DVB (12258): em28xx: fix typo in mt352 init sequence for Terratec Cinergy T XS USB Andy walls pointed out that we were passing 0x5d to the TUNER_GO register, instead of 0x01. Set the register properly (note the code did still work with the incorrect value, so this does not address a regression). Thanks to Andy Walls for noticing the issue. Cc: Andy Walls Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-dvb.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/media/video/em28xx/em28xx-dvb.c b/drivers/media/video/em28xx/em28xx-dvb.c index d57f7583ac6..f3f0e8fe73c 100644 --- a/drivers/media/video/em28xx/em28xx-dvb.c +++ b/drivers/media/video/em28xx/em28xx-dvb.c @@ -272,7 +272,7 @@ static int mt352_terratec_xs_init(struct dvb_frontend *fe) static u8 capt_range_cfg[] = { CAPT_RANGE, 0x32 }; static u8 trl_nom_cfg[] = { TRL_NOMINAL_RATE_1, 0x64, 0x00 }; static u8 tps_given_cfg[] = { TPS_GIVEN_1, 0x40, 0x80, 0x50 }; - static u8 tuner_go[] = { TUNER_GO, 0x5d}; + static u8 tuner_go[] = { TUNER_GO, 0x01}; mt352_write(fe, clock_config, sizeof(clock_config)); udelay(200); -- GitLab From d5b3ba9cb375620a109d79f2e3a7bc21e9b75d8f Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Wed, 8 Jul 2009 21:51:35 -0300 Subject: [PATCH 0294/1342] V4L/DVB (12260): em28xx: make support work for the Pinnacle Hybrid Pro (eb1a:2881) Setup the GPIOs properly and enable support for the DVB side of the Pinnacle Hybrid Pro USB stick. Thanks to Andreas Lunderhage for testing patches and providing a remote debug environment. Cc: Andreas Lunderhage Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 24 +++++++++++++++++++---- drivers/media/video/em28xx/em28xx-dvb.c | 1 + 2 files changed, 21 insertions(+), 4 deletions(-) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 1bd789a52e6..ba20065c24b 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -157,6 +157,20 @@ static struct em28xx_reg_seq evga_indtube_digital[] = { { -1, -1, -1, -1}, }; +/* Pinnacle Hybrid Pro eb1a:2881 */ +static struct em28xx_reg_seq pinnacle_hybrid_pro_analog[] = { + {EM28XX_R08_GPIO, 0x6f, ~EM_GPIO_4, 10}, + { -1, -1, -1, -1}, +}; + +static struct em28xx_reg_seq pinnacle_hybrid_pro_digital[] = { + {EM28XX_R08_GPIO, 0x6e, ~EM_GPIO_4, 10}, + {EM2880_R04_GPO, 0x04, 0xff, 100},/* zl10353 reset */ + {EM2880_R04_GPO, 0x0c, 0xff, 1}, + { -1, -1, -1, -1}, +}; + + /* Callback for the most boards */ static struct em28xx_reg_seq default_tuner_gpio[] = { {EM28XX_R08_GPIO, EM_GPIO_4, EM_GPIO_4, 10}, @@ -1253,25 +1267,26 @@ struct em28xx_board em28xx_boards[] = { }, [EM2881_BOARD_PINNACLE_HYBRID_PRO] = { .name = "Pinnacle Hybrid Pro", - .valid = EM28XX_BOARD_NOT_VALIDATED, .tuner_type = TUNER_XC2028, .tuner_gpio = default_tuner_gpio, .decoder = EM28XX_TVP5150, + .has_dvb = 1, + .dvb_gpio = pinnacle_hybrid_pro_digital, .input = { { .type = EM28XX_VMUX_TELEVISION, .vmux = TVP5150_COMPOSITE0, .amux = EM28XX_AMUX_VIDEO, - .gpio = default_analog, + .gpio = pinnacle_hybrid_pro_analog, }, { .type = EM28XX_VMUX_COMPOSITE1, .vmux = TVP5150_COMPOSITE1, .amux = EM28XX_AMUX_LINE_IN, - .gpio = default_analog, + .gpio = pinnacle_hybrid_pro_analog, }, { .type = EM28XX_VMUX_SVIDEO, .vmux = TVP5150_SVIDEO, .amux = EM28XX_AMUX_LINE_IN, - .gpio = default_analog, + .gpio = pinnacle_hybrid_pro_analog, } }, }, [EM2882_BOARD_PINNACLE_HYBRID_PRO] = { @@ -1641,6 +1656,7 @@ static struct em28xx_hash_table em28xx_eeprom_hash[] = { {0x966a0441, EM2880_BOARD_KWORLD_DVB_310U, TUNER_XC2028}, {0x9567eb1a, EM2880_BOARD_EMPIRE_DUAL_TV, TUNER_XC2028}, {0xcee44a99, EM2882_BOARD_EVGA_INDTUBE, TUNER_XC2028}, + {0xb8846b20, EM2881_BOARD_PINNACLE_HYBRID_PRO, TUNER_XC2028}, }; /* I2C devicelist hash table for devices with generic USB IDs */ diff --git a/drivers/media/video/em28xx/em28xx-dvb.c b/drivers/media/video/em28xx/em28xx-dvb.c index f3f0e8fe73c..5ebc274c1b2 100644 --- a/drivers/media/video/em28xx/em28xx-dvb.c +++ b/drivers/media/video/em28xx/em28xx-dvb.c @@ -489,6 +489,7 @@ static int dvb_init(struct em28xx *dev) } break; case EM2880_BOARD_TERRATEC_HYBRID_XS: + case EM2881_BOARD_PINNACLE_HYBRID_PRO: dvb->frontend = dvb_attach(zl10353_attach, &em28xx_terratec_xs_zl10353_xc3028, &dev->i2c_adap); -- GitLab From 44010440ca2693a07b1252ee836a23804412575e Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Wed, 8 Jul 2009 22:18:15 -0300 Subject: [PATCH 0295/1342] V4L/DVB (12261): em28xx: set GPIO properly for Pinnacle Hybrid Pro analog support Set the GPIO properly for the analog side of the Pinnacle Hybrid Pro, or else the emp202 doesn't get detected properly. Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index ba20065c24b..476acb02a3d 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -159,7 +159,7 @@ static struct em28xx_reg_seq evga_indtube_digital[] = { /* Pinnacle Hybrid Pro eb1a:2881 */ static struct em28xx_reg_seq pinnacle_hybrid_pro_analog[] = { - {EM28XX_R08_GPIO, 0x6f, ~EM_GPIO_4, 10}, + {EM28XX_R08_GPIO, 0xfd, ~EM_GPIO_4, 10}, { -1, -1, -1, -1}, }; -- GitLab From 5343e446014b93f740d5502f9f3bfa3f66dcbc7c Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Wed, 15 Jul 2009 00:35:47 -0300 Subject: [PATCH 0296/1342] V4L/DVB (12262): em28xx: Make sure the tuner is initialized if generic empia USB id was used In cases where the device has a generic Empia USB ID, the call in the precard setup phase did not set the tuner GPIO. As a result, the tuner may not be taken out of reset before attempting initialization in the analog driver. This problem was not seen before with the EVGA inDtube, since that particular board has the analog GPIO setup to include taking the tuner out of reset. Thanks to Andreas Lunderhage for testing patches and providing a remote debug environment for the Pinnacle 320e. Cc: Andreas Lunderhage Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 476acb02a3d..5aef7ddd091 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -2286,6 +2286,7 @@ void em28xx_card_setup(struct em28xx *dev) em28xx_set_mode() in em28xx_pre_card_setup() was a no-op, so make the call now so the analog GPIOs are set properly before probing the i2c bus. */ + em28xx_gpio_set(dev, dev->board.tuner_gpio); em28xx_set_mode(dev, EM28XX_ANALOG_MODE); break; case EM2820_BOARD_SILVERCREST_WEBCAM: -- GitLab From e16e5a3739cfd208de00d49def10fcfa6ceff46f Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Wed, 15 Jul 2009 00:37:22 -0300 Subject: [PATCH 0297/1342] V4L/DVB (12263): em28xx: set demod profile for Pinnacle Hybrid Pro 320e The Pinnacle Hybrid Pro 320e was missing a demod config for the xc3028, which is required for digital tuning to work properly. Add the missing profile. Thanks to Andreas Lunderhage for testing patches and providing a remote debug environment. Cc: Andreas Lunderhage Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 5aef7ddd091..320f1f60276 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -1990,6 +1990,7 @@ static void em28xx_setup_xc3028(struct em28xx *dev, struct xc2028_ctrl *ctl) ctl->demod = XC3028_FE_ZARLINK456; break; case EM2880_BOARD_TERRATEC_HYBRID_XS: + case EM2881_BOARD_PINNACLE_HYBRID_PRO: ctl->demod = XC3028_FE_ZARLINK456; break; case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900_R2: -- GitLab From a84f79aed688a94197387830df3a2f2068f49dc0 Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Sun, 12 Jul 2009 17:05:02 -0300 Subject: [PATCH 0298/1342] V4L/DVB (12265): em28xx: fix tuning problem in HVR-900 (R1) When the change was introduced in the zl10353 for the i2c gate behavior, this broke the HVR-900 which was not behind a gate. Use a version of the zl10353 config profile that indicates the tuner is not behind such a gate. Without this patch the first tune succeeds, but subsequent tuning attempts will fail. The change also renames the terratec zl10353 profile I wrote to be more generic, since it is shared by the non-terratec device. Thanks to Michael Krufky for providing a HVR-900 and DVB-T environment to test with. Cc: Michael Krufky Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-dvb.c | 14 +++++++++++--- 1 file changed, 11 insertions(+), 3 deletions(-) diff --git a/drivers/media/video/em28xx/em28xx-dvb.c b/drivers/media/video/em28xx/em28xx-dvb.c index 5ebc274c1b2..cf0ac7f2a30 100644 --- a/drivers/media/video/em28xx/em28xx-dvb.c +++ b/drivers/media/video/em28xx/em28xx-dvb.c @@ -245,7 +245,7 @@ static struct s5h1409_config em28xx_s5h1409_with_xc3028 = { .mpeg_timing = S5H1409_MPEGTIMING_CONTINOUS_NONINVERTING_CLOCK }; -static struct zl10353_config em28xx_terratec_xs_zl10353_xc3028 = { +static struct zl10353_config em28xx_zl10353_xc3028_no_i2c_gate = { .demod_address = (0x1e >> 1), .no_tuner = 1, .disable_i2c_gate_ctrl = 1, @@ -477,7 +477,6 @@ static int dvb_init(struct em28xx *dev) goto out_free; } break; - case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900: case EM2880_BOARD_KWORLD_DVB_310U: case EM2880_BOARD_EMPIRE_DUAL_TV: dvb->frontend = dvb_attach(zl10353_attach, @@ -488,10 +487,19 @@ static int dvb_init(struct em28xx *dev) goto out_free; } break; + case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900: + dvb->frontend = dvb_attach(zl10353_attach, + &em28xx_zl10353_xc3028_no_i2c_gate, + &dev->i2c_adap); + if (attach_xc3028(0x61, dev) < 0) { + result = -EINVAL; + goto out_free; + } + break; case EM2880_BOARD_TERRATEC_HYBRID_XS: case EM2881_BOARD_PINNACLE_HYBRID_PRO: dvb->frontend = dvb_attach(zl10353_attach, - &em28xx_terratec_xs_zl10353_xc3028, + &em28xx_zl10353_xc3028_no_i2c_gate, &dev->i2c_adap); if (dvb->frontend == NULL) { /* This board could have either a zl10353 or a mt352. -- GitLab From 27954930f047df73a16253db2750345034e56c40 Mon Sep 17 00:00:00 2001 From: Jean-Francois Moine Date: Wed, 8 Jul 2009 05:21:50 -0300 Subject: [PATCH 0299/1342] V4L/DVB (12267): gspca - sonixj: Bad sensor init of non ov76xx sensors. The bug was introduced when adding the light frequency control Signed-off-by: Jean-Francois Moine Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/gspca/sonixj.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/media/video/gspca/sonixj.c b/drivers/media/video/gspca/sonixj.c index 0d02f41fa7d..bad309b90cc 100644 --- a/drivers/media/video/gspca/sonixj.c +++ b/drivers/media/video/gspca/sonixj.c @@ -1634,6 +1634,8 @@ static void setfreq(struct gspca_dev *gspca_dev) { struct sd *sd = (struct sd *) gspca_dev; + if (gspca_dev->ctrl_dis & (1 << FREQ_IDX)) + return; if (sd->sensor == SENSOR_OV7660) { switch (sd->freq) { case 0: /* Banding filter disabled */ -- GitLab From a2f5a8117cb185fc347f35e369a6320e6aa9d82d Mon Sep 17 00:00:00 2001 From: Antti Palosaari Date: Fri, 10 Jul 2009 20:03:43 -0300 Subject: [PATCH 0300/1342] V4L/DVB (12269): af9013: auto-detect parameters in case of garbage given by app Request demodulator auto-detect transmission parameters in case of garbage parameters provided by application for compatibility. That's needed at least for MPlayer compatibility currently. Thanks to Jelle de Jong for reporting issue and providing SSH access to Devin for debugging. Thanks to Devin Heitmueller for hard debug work he did to find that bug. Cc: Devin Heitmueller Cc: Jelle de Jong Signed-off-by: Antti Palosaari Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb/frontends/af9013.c | 25 ++++++++++++++++++------- 1 file changed, 18 insertions(+), 7 deletions(-) diff --git a/drivers/media/dvb/frontends/af9013.c b/drivers/media/dvb/frontends/af9013.c index 136c5863d81..12e018b4107 100644 --- a/drivers/media/dvb/frontends/af9013.c +++ b/drivers/media/dvb/frontends/af9013.c @@ -527,6 +527,10 @@ static int af9013_set_ofdm_params(struct af9013_state *state, u8 i, buf[3] = {0, 0, 0}; *auto_mode = 0; /* set if parameters are requested to auto set */ + /* Try auto-detect transmission parameters in case of AUTO requested or + garbage parameters given by application for compatibility. + MPlayer seems to provide garbage parameters currently. */ + switch (params->transmission_mode) { case TRANSMISSION_MODE_AUTO: *auto_mode = 1; @@ -536,7 +540,8 @@ static int af9013_set_ofdm_params(struct af9013_state *state, buf[0] |= (1 << 0); break; default: - return -EINVAL; + deb_info("%s: invalid transmission_mode\n", __func__); + *auto_mode = 1; } switch (params->guard_interval) { @@ -554,7 +559,8 @@ static int af9013_set_ofdm_params(struct af9013_state *state, buf[0] |= (3 << 2); break; default: - return -EINVAL; + deb_info("%s: invalid guard_interval\n", __func__); + *auto_mode = 1; } switch (params->hierarchy_information) { @@ -572,7 +578,8 @@ static int af9013_set_ofdm_params(struct af9013_state *state, buf[0] |= (3 << 4); break; default: - return -EINVAL; + deb_info("%s: invalid hierarchy_information\n", __func__); + *auto_mode = 1; }; switch (params->constellation) { @@ -587,7 +594,8 @@ static int af9013_set_ofdm_params(struct af9013_state *state, buf[1] |= (2 << 6); break; default: - return -EINVAL; + deb_info("%s: invalid constellation\n", __func__); + *auto_mode = 1; } /* Use HP. How and which case we can switch to LP? */ @@ -611,7 +619,8 @@ static int af9013_set_ofdm_params(struct af9013_state *state, buf[2] |= (4 << 0); break; default: - return -EINVAL; + deb_info("%s: invalid code_rate_HP\n", __func__); + *auto_mode = 1; } switch (params->code_rate_LP) { @@ -638,7 +647,8 @@ static int af9013_set_ofdm_params(struct af9013_state *state, if (params->hierarchy_information == HIERARCHY_AUTO) break; default: - return -EINVAL; + deb_info("%s: invalid code_rate_LP\n", __func__); + *auto_mode = 1; } switch (params->bandwidth) { @@ -651,7 +661,8 @@ static int af9013_set_ofdm_params(struct af9013_state *state, buf[1] |= (2 << 2); break; default: - return -EINVAL; + deb_info("%s: invalid bandwidth\n", __func__); + buf[1] |= (2 << 2); /* cannot auto-detect BW, try 8 MHz */ } /* program */ -- GitLab From af1d9afa75082663ea9e2b67b9381d1af403f52b Mon Sep 17 00:00:00 2001 From: Brian Johnson Date: Sun, 19 Jul 2009 05:29:20 -0300 Subject: [PATCH 0301/1342] V4L/DVB (12282): gspca - main: Support for vidioc_g_chip_ident and vidioc_g/s_register. Signed-off-by: Brian Johnson Signed-off-by: Jean-Francois Moine Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/gspca/gspca.c | 73 +++++++++++++++++++++++++++++++ drivers/media/video/gspca/gspca.h | 9 ++++ 2 files changed, 82 insertions(+) diff --git a/drivers/media/video/gspca/gspca.c b/drivers/media/video/gspca/gspca.c index 1e89600986c..b8561dfb6c8 100644 --- a/drivers/media/video/gspca/gspca.c +++ b/drivers/media/video/gspca/gspca.c @@ -727,6 +727,74 @@ static int gspca_get_mode(struct gspca_dev *gspca_dev, return -EINVAL; } +#ifdef CONFIG_VIDEO_ADV_DEBUG +static int vidioc_g_register(struct file *file, void *priv, + struct v4l2_dbg_register *reg) +{ + int ret; + struct gspca_dev *gspca_dev = priv; + + if (!gspca_dev->sd_desc->get_chip_ident) + return -EINVAL; + + if (!gspca_dev->sd_desc->get_register) + return -EINVAL; + + if (mutex_lock_interruptible(&gspca_dev->usb_lock)) + return -ERESTARTSYS; + if (gspca_dev->present) + ret = gspca_dev->sd_desc->get_register(gspca_dev, reg); + else + ret = -ENODEV; + mutex_unlock(&gspca_dev->usb_lock); + + return ret; +} + +static int vidioc_s_register(struct file *file, void *priv, + struct v4l2_dbg_register *reg) +{ + int ret; + struct gspca_dev *gspca_dev = priv; + + if (!gspca_dev->sd_desc->get_chip_ident) + return -EINVAL; + + if (!gspca_dev->sd_desc->set_register) + return -EINVAL; + + if (mutex_lock_interruptible(&gspca_dev->usb_lock)) + return -ERESTARTSYS; + if (gspca_dev->present) + ret = gspca_dev->sd_desc->set_register(gspca_dev, reg); + else + ret = -ENODEV; + mutex_unlock(&gspca_dev->usb_lock); + + return ret; +} +#endif + +static int vidioc_g_chip_ident(struct file *file, void *priv, + struct v4l2_dbg_chip_ident *chip) +{ + int ret; + struct gspca_dev *gspca_dev = priv; + + if (!gspca_dev->sd_desc->get_chip_ident) + return -EINVAL; + + if (mutex_lock_interruptible(&gspca_dev->usb_lock)) + return -ERESTARTSYS; + if (gspca_dev->present) + ret = gspca_dev->sd_desc->get_chip_ident(gspca_dev, chip); + else + ret = -ENODEV; + mutex_unlock(&gspca_dev->usb_lock); + + return ret; +} + static int vidioc_enum_fmt_vid_cap(struct file *file, void *priv, struct v4l2_fmtdesc *fmtdesc) { @@ -1883,6 +1951,11 @@ static const struct v4l2_ioctl_ops dev_ioctl_ops = { .vidioc_s_parm = vidioc_s_parm, .vidioc_s_std = vidioc_s_std, .vidioc_enum_framesizes = vidioc_enum_framesizes, +#ifdef CONFIG_VIDEO_ADV_DEBUG + .vidioc_g_register = vidioc_g_register, + .vidioc_s_register = vidioc_s_register, +#endif + .vidioc_g_chip_ident = vidioc_g_chip_ident, #ifdef CONFIG_VIDEO_V4L1_COMPAT .vidiocgmbuf = vidiocgmbuf, #endif diff --git a/drivers/media/video/gspca/gspca.h b/drivers/media/video/gspca/gspca.h index bd1faff8864..46c4effdfcd 100644 --- a/drivers/media/video/gspca/gspca.h +++ b/drivers/media/video/gspca/gspca.h @@ -69,6 +69,10 @@ typedef void (*cam_v_op) (struct gspca_dev *); typedef int (*cam_cf_op) (struct gspca_dev *, const struct usb_device_id *); typedef int (*cam_jpg_op) (struct gspca_dev *, struct v4l2_jpegcompression *); +typedef int (*cam_reg_op) (struct gspca_dev *, + struct v4l2_dbg_register *); +typedef int (*cam_ident_op) (struct gspca_dev *, + struct v4l2_dbg_chip_ident *); typedef int (*cam_streamparm_op) (struct gspca_dev *, struct v4l2_streamparm *); typedef int (*cam_qmnu_op) (struct gspca_dev *, @@ -105,6 +109,11 @@ struct sd_desc { cam_qmnu_op querymenu; cam_streamparm_op get_streamparm; cam_streamparm_op set_streamparm; +#ifdef CONFIG_VIDEO_ADV_DEBUG + cam_reg_op set_register; + cam_reg_op get_register; +#endif + cam_ident_op get_chip_ident; }; /* packet types when moving from iso buf to frame buf */ -- GitLab From 26e744b6b61066203fd57de0d3962353621e06f8 Mon Sep 17 00:00:00 2001 From: Brian Johnson Date: Sun, 19 Jul 2009 05:52:58 -0300 Subject: [PATCH 0302/1342] V4L/DVB (12283): gspca - sn9c20x: New subdriver for sn9c201 and sn9c202 bridges. Signed-off-by: Brian Johnson Signed-off-by: Jean-Francois Moine Signed-off-by: Mauro Carvalho Chehab --- Documentation/video4linux/gspca.txt | 32 + drivers/media/video/gspca/Kconfig | 16 + drivers/media/video/gspca/Makefile | 2 + drivers/media/video/gspca/sn9c20x.c | 2433 +++++++++++++++++++++++++++ include/linux/videodev2.h | 1 + include/media/v4l2-chip-ident.h | 12 + 6 files changed, 2496 insertions(+) create mode 100644 drivers/media/video/gspca/sn9c20x.c diff --git a/Documentation/video4linux/gspca.txt b/Documentation/video4linux/gspca.txt index 2bcf78896e2..573f95b5880 100644 --- a/Documentation/video4linux/gspca.txt +++ b/Documentation/video4linux/gspca.txt @@ -44,7 +44,9 @@ zc3xx 0458:7007 Genius VideoCam V2 zc3xx 0458:700c Genius VideoCam V3 zc3xx 0458:700f Genius VideoCam Web V2 sonixj 0458:7025 Genius Eye 311Q +sn9c20x 0458:7029 Genius Look 320s sonixj 0458:702e Genius Slim 310 NB +sn9c20x 045e:00f4 LifeCam VX-6000 (SN9C20x + OV9650) sonixj 045e:00f5 MicroSoft VX3000 sonixj 045e:00f7 MicroSoft VX1000 ov519 045e:028c Micro$oft xbox cam @@ -282,6 +284,28 @@ sonixj 0c45:613a Microdia Sonix PC Camera sonixj 0c45:613b Surfer SN-206 sonixj 0c45:613c Sonix Pccam168 sonixj 0c45:6143 Sonix Pccam168 +sn9c20x 0c45:6240 PC Camera (SN9C201 + MT9M001) +sn9c20x 0c45:6242 PC Camera (SN9C201 + MT9M111) +sn9c20x 0c45:6248 PC Camera (SN9C201 + OV9655) +sn9c20x 0c45:624e PC Camera (SN9C201 + SOI968) +sn9c20x 0c45:624f PC Camera (SN9C201 + OV9650) +sn9c20x 0c45:6251 PC Camera (SN9C201 + OV9650) +sn9c20x 0c45:6253 PC Camera (SN9C201 + OV9650) +sn9c20x 0c45:6260 PC Camera (SN9C201 + OV7670) +sn9c20x 0c45:6270 PC Camera (SN9C201 + MT9V011/MT9V111/MT9V112) +sn9c20x 0c45:627b PC Camera (SN9C201 + OV7660) +sn9c20x 0c45:627c PC Camera (SN9C201 + HV7131R) +sn9c20x 0c45:627f PC Camera (SN9C201 + OV9650) +sn9c20x 0c45:6280 PC Camera (SN9C202 + MT9M001) +sn9c20x 0c45:6282 PC Camera (SN9C202 + MT9M111) +sn9c20x 0c45:6288 PC Camera (SN9C202 + OV9655) +sn9c20x 0c45:628e PC Camera (SN9C202 + SOI968) +sn9c20x 0c45:628f PC Camera (SN9C202 + OV9650) +sn9c20x 0c45:62a0 PC Camera (SN9C202 + OV7670) +sn9c20x 0c45:62b0 PC Camera (SN9C202 + MT9V011/MT9V111/MT9V112) +sn9c20x 0c45:62b3 PC Camera (SN9C202 + OV9655) +sn9c20x 0c45:62bb PC Camera (SN9C202 + OV7660) +sn9c20x 0c45:62bc PC Camera (SN9C202 + HV7131R) sunplus 0d64:0303 Sunplus FashionCam DXG etoms 102c:6151 Qcam Sangha CIF etoms 102c:6251 Qcam xxxxxx VGA @@ -290,6 +314,7 @@ spca561 10fd:7e50 FlyCam Usb 100 zc3xx 10fd:8050 Typhoon Webshot II USB 300k ov534 1415:2000 Sony HD Eye for PS3 (SLEH 00201) pac207 145f:013a Trust WB-1300N +sn9c20x 145f:013d Trust WB-3600R vc032x 15b8:6001 HP 2.0 Megapixel vc032x 15b8:6002 HP 2.0 Megapixel rz406aa spca501 1776:501c Arowana 300K CMOS Camera @@ -300,4 +325,11 @@ spca500 2899:012c Toptro Industrial spca508 8086:0110 Intel Easy PC Camera spca500 8086:0630 Intel Pocket PC Camera spca506 99fa:8988 Grandtec V.cap +sn9c20x a168:0610 Dino-Lite Digital Microscope (SN9C201 + HV7131R) +sn9c20x a168:0611 Dino-Lite Digital Microscope (SN9C201 + HV7131R) +sn9c20x a168:0613 Dino-Lite Digital Microscope (SN9C201 + HV7131R) +sn9c20x a168:0618 Dino-Lite Digital Microscope (SN9C201 + HV7131R) +sn9c20x a168:0614 Dino-Lite Digital Microscope (SN9C201 + MT9M111) +sn9c20x a168:0615 Dino-Lite Digital Microscope (SN9C201 + MT9M111) +sn9c20x a168:0617 Dino-Lite Digital Microscope (SN9C201 + MT9M111) spca561 abcd:cdee Petcam diff --git a/drivers/media/video/gspca/Kconfig b/drivers/media/video/gspca/Kconfig index 578dc4ffc96..34f46f2bc04 100644 --- a/drivers/media/video/gspca/Kconfig +++ b/drivers/media/video/gspca/Kconfig @@ -102,6 +102,22 @@ config USB_GSPCA_PAC7311 To compile this driver as a module, choose M here: the module will be called gspca_pac7311. +config USB_GSPCA_SN9C20X + tristate "SN9C20X USB Camera Driver" + depends on VIDEO_V4L2 && USB_GSPCA + help + Say Y here if you want support for cameras based on the + sn9c20x chips (SN9C201 and SN9C202). + + To compile this driver as a module, choose M here: the + module will be called gspca_sn9c20x. + +config USB_GSPCA_SN9C20X_EVDEV + bool "Enable evdev support" + depends on USB_GSPCA_SN9C20X + ---help--- + Say Y here in order to enable evdev support for sn9c20x webcam button. + config USB_GSPCA_SONIXB tristate "SONIX Bayer USB Camera Driver" depends on VIDEO_V4L2 && USB_GSPCA diff --git a/drivers/media/video/gspca/Makefile b/drivers/media/video/gspca/Makefile index 8a6643e8eb9..f6d3b86e9ad 100644 --- a/drivers/media/video/gspca/Makefile +++ b/drivers/media/video/gspca/Makefile @@ -8,6 +8,7 @@ obj-$(CONFIG_USB_GSPCA_OV519) += gspca_ov519.o obj-$(CONFIG_USB_GSPCA_OV534) += gspca_ov534.o obj-$(CONFIG_USB_GSPCA_PAC207) += gspca_pac207.o obj-$(CONFIG_USB_GSPCA_PAC7311) += gspca_pac7311.o +obj-$(CONFIG_USB_GSPCA_SN9C20X) += gspca_sn9c20x.o obj-$(CONFIG_USB_GSPCA_SONIXB) += gspca_sonixb.o obj-$(CONFIG_USB_GSPCA_SONIXJ) += gspca_sonixj.o obj-$(CONFIG_USB_GSPCA_SPCA500) += gspca_spca500.o @@ -35,6 +36,7 @@ gspca_ov519-objs := ov519.o gspca_ov534-objs := ov534.o gspca_pac207-objs := pac207.o gspca_pac7311-objs := pac7311.o +gspca_sn9c20x-objs := sn9c20x.o gspca_sonixb-objs := sonixb.o gspca_sonixj-objs := sonixj.o gspca_spca500-objs := spca500.o diff --git a/drivers/media/video/gspca/sn9c20x.c b/drivers/media/video/gspca/sn9c20x.c new file mode 100644 index 00000000000..78ab26ceb90 --- /dev/null +++ b/drivers/media/video/gspca/sn9c20x.c @@ -0,0 +1,2433 @@ +/* + * Sonix sn9c201 sn9c202 library + * Copyright (C) 2008-2009 microdia project + * Copyright (C) 2009 Brian Johnson + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include "gspca.h" +#include "jpeg.h" + +#include +#ifdef CONFIG_USB_GSPCA_SN9C20X_EVDEV +#include +#include +#include +#include +#endif + +MODULE_AUTHOR("Brian Johnson , " + "microdia project "); +MODULE_DESCRIPTION("GSPCA/SN9C20X USB Camera Driver"); +MODULE_LICENSE("GPL"); + +#define MODULE_NAME "sn9c20x" + +#define MODE_RAW 0x10 +#define MODE_JPEG 0x20 +#define MODE_SXGA 0x80 + +#define SENSOR_OV9650 0 +#define SENSOR_OV9655 1 +#define SENSOR_SOI968 2 +#define SENSOR_OV7660 3 +#define SENSOR_OV7670 4 +#define SENSOR_MT9V011 5 +#define SENSOR_MT9V111 6 +#define SENSOR_MT9V112 7 +#define SENSOR_MT9M001 8 +#define SENSOR_MT9M111 9 +#define SENSOR_HV7131R 10 +#define SENSOR_MT9VPRB 20 + +/* specific webcam descriptor */ +struct sd { + struct gspca_dev gspca_dev; + +#define MIN_AVG_LUM 80 +#define MAX_AVG_LUM 130 + atomic_t avg_lum; + u8 old_step; + u8 older_step; + u8 exposure_step; + + u8 brightness; + u8 contrast; + u8 saturation; + s16 hue; + u8 gamma; + u8 red; + u8 blue; + + u8 hflip; + u8 vflip; + u8 gain; + u16 exposure; + u8 auto_exposure; + + u8 i2c_addr; + u8 sensor; + u8 hstart; + u8 vstart; + + u8 *jpeg_hdr; + u8 quality; + +#ifdef CONFIG_USB_GSPCA_SN9C20X_EVDEV + struct input_dev *input_dev; + u8 input_gpio; + struct task_struct *input_task; +#endif +}; + +static int sd_setbrightness(struct gspca_dev *gspca_dev, s32 val); +static int sd_getbrightness(struct gspca_dev *gspca_dev, s32 *val); +static int sd_setcontrast(struct gspca_dev *gspca_dev, s32 val); +static int sd_getcontrast(struct gspca_dev *gspca_dev, s32 *val); +static int sd_setsaturation(struct gspca_dev *gspca_dev, s32 val); +static int sd_getsaturation(struct gspca_dev *gspca_dev, s32 *val); +static int sd_sethue(struct gspca_dev *gspca_dev, s32 val); +static int sd_gethue(struct gspca_dev *gspca_dev, s32 *val); +static int sd_setgamma(struct gspca_dev *gspca_dev, s32 val); +static int sd_getgamma(struct gspca_dev *gspca_dev, s32 *val); +static int sd_setredbalance(struct gspca_dev *gspca_dev, s32 val); +static int sd_getredbalance(struct gspca_dev *gspca_dev, s32 *val); +static int sd_setbluebalance(struct gspca_dev *gspca_dev, s32 val); +static int sd_getbluebalance(struct gspca_dev *gspca_dev, s32 *val); +static int sd_setvflip(struct gspca_dev *gspca_dev, s32 val); +static int sd_getvflip(struct gspca_dev *gspca_dev, s32 *val); +static int sd_sethflip(struct gspca_dev *gspca_dev, s32 val); +static int sd_gethflip(struct gspca_dev *gspca_dev, s32 *val); +static int sd_setgain(struct gspca_dev *gspca_dev, s32 val); +static int sd_getgain(struct gspca_dev *gspca_dev, s32 *val); +static int sd_setexposure(struct gspca_dev *gspca_dev, s32 val); +static int sd_getexposure(struct gspca_dev *gspca_dev, s32 *val); +static int sd_setautoexposure(struct gspca_dev *gspca_dev, s32 val); +static int sd_getautoexposure(struct gspca_dev *gspca_dev, s32 *val); + +static struct ctrl sd_ctrls[] = { + { +#define BRIGHTNESS_IDX 0 + { + .id = V4L2_CID_BRIGHTNESS, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Brightness", + .minimum = 0, + .maximum = 0xff, + .step = 1, +#define BRIGHTNESS_DEFAULT 0x7f + .default_value = BRIGHTNESS_DEFAULT, + }, + .set = sd_setbrightness, + .get = sd_getbrightness, + }, + { +#define CONTRAST_IDX 1 + { + .id = V4L2_CID_CONTRAST, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Contrast", + .minimum = 0, + .maximum = 0xff, + .step = 1, +#define CONTRAST_DEFAULT 0x7f + .default_value = CONTRAST_DEFAULT, + }, + .set = sd_setcontrast, + .get = sd_getcontrast, + }, + { +#define SATURATION_IDX 2 + { + .id = V4L2_CID_SATURATION, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Saturation", + .minimum = 0, + .maximum = 0xff, + .step = 1, +#define SATURATION_DEFAULT 0x7f + .default_value = SATURATION_DEFAULT, + }, + .set = sd_setsaturation, + .get = sd_getsaturation, + }, + { +#define HUE_IDX 3 + { + .id = V4L2_CID_HUE, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Hue", + .minimum = -180, + .maximum = 180, + .step = 1, +#define HUE_DEFAULT 0 + .default_value = HUE_DEFAULT, + }, + .set = sd_sethue, + .get = sd_gethue, + }, + { +#define GAMMA_IDX 4 + { + .id = V4L2_CID_GAMMA, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Gamma", + .minimum = 0, + .maximum = 0xff, + .step = 1, +#define GAMMA_DEFAULT 0x10 + .default_value = GAMMA_DEFAULT, + }, + .set = sd_setgamma, + .get = sd_getgamma, + }, + { +#define BLUE_IDX 5 + { + .id = V4L2_CID_BLUE_BALANCE, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Blue Balance", + .minimum = 0, + .maximum = 0x7f, + .step = 1, +#define BLUE_DEFAULT 0x28 + .default_value = BLUE_DEFAULT, + }, + .set = sd_setbluebalance, + .get = sd_getbluebalance, + }, + { +#define RED_IDX 6 + { + .id = V4L2_CID_RED_BALANCE, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Red Balance", + .minimum = 0, + .maximum = 0x7f, + .step = 1, +#define RED_DEFAULT 0x28 + .default_value = RED_DEFAULT, + }, + .set = sd_setredbalance, + .get = sd_getredbalance, + }, + { +#define HFLIP_IDX 7 + { + .id = V4L2_CID_HFLIP, + .type = V4L2_CTRL_TYPE_BOOLEAN, + .name = "Horizontal Flip", + .minimum = 0, + .maximum = 1, + .step = 1, +#define HFLIP_DEFAULT 0 + .default_value = HFLIP_DEFAULT, + }, + .set = sd_sethflip, + .get = sd_gethflip, + }, + { +#define VFLIP_IDX 8 + { + .id = V4L2_CID_VFLIP, + .type = V4L2_CTRL_TYPE_BOOLEAN, + .name = "Vertical Flip", + .minimum = 0, + .maximum = 1, + .step = 1, +#define VFLIP_DEFAULT 0 + .default_value = VFLIP_DEFAULT, + }, + .set = sd_setvflip, + .get = sd_getvflip, + }, + { +#define EXPOSURE_IDX 9 + { + .id = V4L2_CID_EXPOSURE, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Exposure", + .minimum = 0, + .maximum = 0x1780, + .step = 1, +#define EXPOSURE_DEFAULT 0x33 + .default_value = EXPOSURE_DEFAULT, + }, + .set = sd_setexposure, + .get = sd_getexposure, + }, + { +#define GAIN_IDX 10 + { + .id = V4L2_CID_GAIN, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Gain", + .minimum = 0, + .maximum = 28, + .step = 1, +#define GAIN_DEFAULT 0x00 + .default_value = GAIN_DEFAULT, + }, + .set = sd_setgain, + .get = sd_getgain, + }, + { +#define AUTOGAIN_IDX 11 + { + .id = V4L2_CID_AUTOGAIN, + .type = V4L2_CTRL_TYPE_BOOLEAN, + .name = "Auto Exposure", + .minimum = 0, + .maximum = 1, + .step = 1, +#define AUTO_EXPOSURE_DEFAULT 1 + .default_value = AUTO_EXPOSURE_DEFAULT, + }, + .set = sd_setautoexposure, + .get = sd_getautoexposure, + }, +}; + +static const struct v4l2_pix_format vga_mode[] = { + {160, 120, V4L2_PIX_FMT_JPEG, V4L2_FIELD_NONE, + .bytesperline = 240, + .sizeimage = 240 * 120, + .colorspace = V4L2_COLORSPACE_JPEG, + .priv = 0 | MODE_JPEG}, + {160, 120, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE, + .bytesperline = 160, + .sizeimage = 160 * 120, + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 0 | MODE_RAW}, + {160, 120, V4L2_PIX_FMT_SN9C20X_I420, V4L2_FIELD_NONE, + .bytesperline = 240, + .sizeimage = 240 * 120, + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 0}, + {320, 240, V4L2_PIX_FMT_JPEG, V4L2_FIELD_NONE, + .bytesperline = 480, + .sizeimage = 480 * 240 , + .colorspace = V4L2_COLORSPACE_JPEG, + .priv = 1 | MODE_JPEG}, + {320, 240, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE, + .bytesperline = 320, + .sizeimage = 320 * 240 , + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 1 | MODE_RAW}, + {320, 240, V4L2_PIX_FMT_SN9C20X_I420, V4L2_FIELD_NONE, + .bytesperline = 480, + .sizeimage = 480 * 240 , + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 1}, + {640, 480, V4L2_PIX_FMT_JPEG, V4L2_FIELD_NONE, + .bytesperline = 960, + .sizeimage = 960 * 480, + .colorspace = V4L2_COLORSPACE_JPEG, + .priv = 2 | MODE_JPEG}, + {640, 480, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE, + .bytesperline = 640, + .sizeimage = 640 * 480, + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 2 | MODE_RAW}, + {640, 480, V4L2_PIX_FMT_SN9C20X_I420, V4L2_FIELD_NONE, + .bytesperline = 960, + .sizeimage = 960 * 480, + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 2}, +}; + +static const struct v4l2_pix_format sxga_mode[] = { + {160, 120, V4L2_PIX_FMT_JPEG, V4L2_FIELD_NONE, + .bytesperline = 240, + .sizeimage = 240 * 120, + .colorspace = V4L2_COLORSPACE_JPEG, + .priv = 0 | MODE_JPEG}, + {160, 120, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE, + .bytesperline = 160, + .sizeimage = 160 * 120, + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 0 | MODE_RAW}, + {160, 120, V4L2_PIX_FMT_SN9C20X_I420, V4L2_FIELD_NONE, + .bytesperline = 240, + .sizeimage = 240 * 120, + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 0}, + {320, 240, V4L2_PIX_FMT_JPEG, V4L2_FIELD_NONE, + .bytesperline = 480, + .sizeimage = 480 * 240 , + .colorspace = V4L2_COLORSPACE_JPEG, + .priv = 1 | MODE_JPEG}, + {320, 240, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE, + .bytesperline = 320, + .sizeimage = 320 * 240 , + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 1 | MODE_RAW}, + {320, 240, V4L2_PIX_FMT_SN9C20X_I420, V4L2_FIELD_NONE, + .bytesperline = 480, + .sizeimage = 480 * 240 , + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 1}, + {640, 480, V4L2_PIX_FMT_JPEG, V4L2_FIELD_NONE, + .bytesperline = 960, + .sizeimage = 960 * 480, + .colorspace = V4L2_COLORSPACE_JPEG, + .priv = 2 | MODE_JPEG}, + {640, 480, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE, + .bytesperline = 640, + .sizeimage = 640 * 480, + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 2 | MODE_RAW}, + {640, 480, V4L2_PIX_FMT_SN9C20X_I420, V4L2_FIELD_NONE, + .bytesperline = 960, + .sizeimage = 960 * 480, + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 2}, + {1280, 1024, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE, + .bytesperline = 1280, + .sizeimage = (1280 * 1024) + 64, + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 3 | MODE_RAW | MODE_SXGA}, +}; + +static const int hsv_red_x[] = { + 41, 44, 46, 48, 50, 52, 54, 56, + 58, 60, 62, 64, 66, 68, 70, 72, + 74, 76, 78, 80, 81, 83, 85, 87, + 88, 90, 92, 93, 95, 97, 98, 100, + 101, 102, 104, 105, 107, 108, 109, 110, + 112, 113, 114, 115, 116, 117, 118, 119, + 120, 121, 122, 123, 123, 124, 125, 125, + 126, 127, 127, 128, 128, 129, 129, 129, + 130, 130, 130, 130, 131, 131, 131, 131, + 131, 131, 131, 131, 130, 130, 130, 130, + 129, 129, 129, 128, 128, 127, 127, 126, + 125, 125, 124, 123, 122, 122, 121, 120, + 119, 118, 117, 116, 115, 114, 112, 111, + 110, 109, 107, 106, 105, 103, 102, 101, + 99, 98, 96, 94, 93, 91, 90, 88, + 86, 84, 83, 81, 79, 77, 75, 74, + 72, 70, 68, 66, 64, 62, 60, 58, + 56, 54, 52, 49, 47, 45, 43, 41, + 39, 36, 34, 32, 30, 28, 25, 23, + 21, 19, 16, 14, 12, 9, 7, 5, + 3, 0, -1, -3, -6, -8, -10, -12, + -15, -17, -19, -22, -24, -26, -28, -30, + -33, -35, -37, -39, -41, -44, -46, -48, + -50, -52, -54, -56, -58, -60, -62, -64, + -66, -68, -70, -72, -74, -76, -78, -80, + -81, -83, -85, -87, -88, -90, -92, -93, + -95, -97, -98, -100, -101, -102, -104, -105, + -107, -108, -109, -110, -112, -113, -114, -115, + -116, -117, -118, -119, -120, -121, -122, -123, + -123, -124, -125, -125, -126, -127, -127, -128, + -128, -128, -128, -128, -128, -128, -128, -128, + -128, -128, -128, -128, -128, -128, -128, -128, + -128, -128, -128, -128, -128, -128, -128, -128, + -128, -127, -127, -126, -125, -125, -124, -123, + -122, -122, -121, -120, -119, -118, -117, -116, + -115, -114, -112, -111, -110, -109, -107, -106, + -105, -103, -102, -101, -99, -98, -96, -94, + -93, -91, -90, -88, -86, -84, -83, -81, + -79, -77, -75, -74, -72, -70, -68, -66, + -64, -62, -60, -58, -56, -54, -52, -49, + -47, -45, -43, -41, -39, -36, -34, -32, + -30, -28, -25, -23, -21, -19, -16, -14, + -12, -9, -7, -5, -3, 0, 1, 3, + 6, 8, 10, 12, 15, 17, 19, 22, + 24, 26, 28, 30, 33, 35, 37, 39, 41 +}; + +static const int hsv_red_y[] = { + 82, 80, 78, 76, 74, 73, 71, 69, + 67, 65, 63, 61, 58, 56, 54, 52, + 50, 48, 46, 44, 41, 39, 37, 35, + 32, 30, 28, 26, 23, 21, 19, 16, + 14, 12, 10, 7, 5, 3, 0, -1, + -3, -6, -8, -10, -13, -15, -17, -19, + -22, -24, -26, -29, -31, -33, -35, -38, + -40, -42, -44, -46, -48, -51, -53, -55, + -57, -59, -61, -63, -65, -67, -69, -71, + -73, -75, -77, -79, -81, -82, -84, -86, + -88, -89, -91, -93, -94, -96, -98, -99, + -101, -102, -104, -105, -106, -108, -109, -110, + -112, -113, -114, -115, -116, -117, -119, -120, + -120, -121, -122, -123, -124, -125, -126, -126, + -127, -128, -128, -128, -128, -128, -128, -128, + -128, -128, -128, -128, -128, -128, -128, -128, + -128, -128, -128, -128, -128, -128, -128, -128, + -128, -128, -128, -128, -128, -128, -128, -128, + -127, -127, -126, -125, -125, -124, -123, -122, + -121, -120, -119, -118, -117, -116, -115, -114, + -113, -111, -110, -109, -107, -106, -105, -103, + -102, -100, -99, -97, -96, -94, -92, -91, + -89, -87, -85, -84, -82, -80, -78, -76, + -74, -73, -71, -69, -67, -65, -63, -61, + -58, -56, -54, -52, -50, -48, -46, -44, + -41, -39, -37, -35, -32, -30, -28, -26, + -23, -21, -19, -16, -14, -12, -10, -7, + -5, -3, 0, 1, 3, 6, 8, 10, + 13, 15, 17, 19, 22, 24, 26, 29, + 31, 33, 35, 38, 40, 42, 44, 46, + 48, 51, 53, 55, 57, 59, 61, 63, + 65, 67, 69, 71, 73, 75, 77, 79, + 81, 82, 84, 86, 88, 89, 91, 93, + 94, 96, 98, 99, 101, 102, 104, 105, + 106, 108, 109, 110, 112, 113, 114, 115, + 116, 117, 119, 120, 120, 121, 122, 123, + 124, 125, 126, 126, 127, 128, 128, 129, + 129, 130, 130, 131, 131, 131, 131, 132, + 132, 132, 132, 132, 132, 132, 132, 132, + 132, 132, 132, 131, 131, 131, 130, 130, + 130, 129, 129, 128, 127, 127, 126, 125, + 125, 124, 123, 122, 121, 120, 119, 118, + 117, 116, 115, 114, 113, 111, 110, 109, + 107, 106, 105, 103, 102, 100, 99, 97, + 96, 94, 92, 91, 89, 87, 85, 84, 82 +}; + +static const int hsv_green_x[] = { + -124, -124, -125, -125, -125, -125, -125, -125, + -125, -126, -126, -125, -125, -125, -125, -125, + -125, -124, -124, -124, -123, -123, -122, -122, + -121, -121, -120, -120, -119, -118, -117, -117, + -116, -115, -114, -113, -112, -111, -110, -109, + -108, -107, -105, -104, -103, -102, -100, -99, + -98, -96, -95, -93, -92, -91, -89, -87, + -86, -84, -83, -81, -79, -77, -76, -74, + -72, -70, -69, -67, -65, -63, -61, -59, + -57, -55, -53, -51, -49, -47, -45, -43, + -41, -39, -37, -35, -33, -30, -28, -26, + -24, -22, -20, -18, -15, -13, -11, -9, + -7, -4, -2, 0, 1, 3, 6, 8, + 10, 12, 14, 17, 19, 21, 23, 25, + 27, 29, 32, 34, 36, 38, 40, 42, + 44, 46, 48, 50, 52, 54, 56, 58, + 60, 62, 64, 66, 68, 70, 71, 73, + 75, 77, 78, 80, 82, 83, 85, 87, + 88, 90, 91, 93, 94, 96, 97, 98, + 100, 101, 102, 104, 105, 106, 107, 108, + 109, 111, 112, 113, 113, 114, 115, 116, + 117, 118, 118, 119, 120, 120, 121, 122, + 122, 123, 123, 124, 124, 124, 125, 125, + 125, 125, 125, 125, 125, 126, 126, 125, + 125, 125, 125, 125, 125, 124, 124, 124, + 123, 123, 122, 122, 121, 121, 120, 120, + 119, 118, 117, 117, 116, 115, 114, 113, + 112, 111, 110, 109, 108, 107, 105, 104, + 103, 102, 100, 99, 98, 96, 95, 93, + 92, 91, 89, 87, 86, 84, 83, 81, + 79, 77, 76, 74, 72, 70, 69, 67, + 65, 63, 61, 59, 57, 55, 53, 51, + 49, 47, 45, 43, 41, 39, 37, 35, + 33, 30, 28, 26, 24, 22, 20, 18, + 15, 13, 11, 9, 7, 4, 2, 0, + -1, -3, -6, -8, -10, -12, -14, -17, + -19, -21, -23, -25, -27, -29, -32, -34, + -36, -38, -40, -42, -44, -46, -48, -50, + -52, -54, -56, -58, -60, -62, -64, -66, + -68, -70, -71, -73, -75, -77, -78, -80, + -82, -83, -85, -87, -88, -90, -91, -93, + -94, -96, -97, -98, -100, -101, -102, -104, + -105, -106, -107, -108, -109, -111, -112, -113, + -113, -114, -115, -116, -117, -118, -118, -119, + -120, -120, -121, -122, -122, -123, -123, -124, -124 +}; + +static const int hsv_green_y[] = { + -100, -99, -98, -97, -95, -94, -93, -91, + -90, -89, -87, -86, -84, -83, -81, -80, + -78, -76, -75, -73, -71, -70, -68, -66, + -64, -63, -61, -59, -57, -55, -53, -51, + -49, -48, -46, -44, -42, -40, -38, -36, + -34, -32, -30, -27, -25, -23, -21, -19, + -17, -15, -13, -11, -9, -7, -4, -2, + 0, 1, 3, 5, 7, 9, 11, 14, + 16, 18, 20, 22, 24, 26, 28, 30, + 32, 34, 36, 38, 40, 42, 44, 46, + 48, 50, 52, 54, 56, 58, 59, 61, + 63, 65, 67, 68, 70, 72, 74, 75, + 77, 78, 80, 82, 83, 85, 86, 88, + 89, 90, 92, 93, 95, 96, 97, 98, + 100, 101, 102, 103, 104, 105, 106, 107, + 108, 109, 110, 111, 112, 112, 113, 114, + 115, 115, 116, 116, 117, 117, 118, 118, + 119, 119, 119, 120, 120, 120, 120, 120, + 121, 121, 121, 121, 121, 121, 120, 120, + 120, 120, 120, 119, 119, 119, 118, 118, + 117, 117, 116, 116, 115, 114, 114, 113, + 112, 111, 111, 110, 109, 108, 107, 106, + 105, 104, 103, 102, 100, 99, 98, 97, + 95, 94, 93, 91, 90, 89, 87, 86, + 84, 83, 81, 80, 78, 76, 75, 73, + 71, 70, 68, 66, 64, 63, 61, 59, + 57, 55, 53, 51, 49, 48, 46, 44, + 42, 40, 38, 36, 34, 32, 30, 27, + 25, 23, 21, 19, 17, 15, 13, 11, + 9, 7, 4, 2, 0, -1, -3, -5, + -7, -9, -11, -14, -16, -18, -20, -22, + -24, -26, -28, -30, -32, -34, -36, -38, + -40, -42, -44, -46, -48, -50, -52, -54, + -56, -58, -59, -61, -63, -65, -67, -68, + -70, -72, -74, -75, -77, -78, -80, -82, + -83, -85, -86, -88, -89, -90, -92, -93, + -95, -96, -97, -98, -100, -101, -102, -103, + -104, -105, -106, -107, -108, -109, -110, -111, + -112, -112, -113, -114, -115, -115, -116, -116, + -117, -117, -118, -118, -119, -119, -119, -120, + -120, -120, -120, -120, -121, -121, -121, -121, + -121, -121, -120, -120, -120, -120, -120, -119, + -119, -119, -118, -118, -117, -117, -116, -116, + -115, -114, -114, -113, -112, -111, -111, -110, + -109, -108, -107, -106, -105, -104, -103, -102, -100 +}; + +static const int hsv_blue_x[] = { + 112, 113, 114, 114, 115, 116, 117, 117, + 118, 118, 119, 119, 120, 120, 120, 121, + 121, 121, 122, 122, 122, 122, 122, 122, + 122, 122, 122, 122, 122, 122, 121, 121, + 121, 120, 120, 120, 119, 119, 118, 118, + 117, 116, 116, 115, 114, 113, 113, 112, + 111, 110, 109, 108, 107, 106, 105, 104, + 103, 102, 100, 99, 98, 97, 95, 94, + 93, 91, 90, 88, 87, 85, 84, 82, + 80, 79, 77, 76, 74, 72, 70, 69, + 67, 65, 63, 61, 60, 58, 56, 54, + 52, 50, 48, 46, 44, 42, 40, 38, + 36, 34, 32, 30, 28, 26, 24, 22, + 19, 17, 15, 13, 11, 9, 7, 5, + 2, 0, -1, -3, -5, -7, -9, -12, + -14, -16, -18, -20, -22, -24, -26, -28, + -31, -33, -35, -37, -39, -41, -43, -45, + -47, -49, -51, -53, -54, -56, -58, -60, + -62, -64, -66, -67, -69, -71, -73, -74, + -76, -78, -79, -81, -83, -84, -86, -87, + -89, -90, -92, -93, -94, -96, -97, -98, + -99, -101, -102, -103, -104, -105, -106, -107, + -108, -109, -110, -111, -112, -113, -114, -114, + -115, -116, -117, -117, -118, -118, -119, -119, + -120, -120, -120, -121, -121, -121, -122, -122, + -122, -122, -122, -122, -122, -122, -122, -122, + -122, -122, -121, -121, -121, -120, -120, -120, + -119, -119, -118, -118, -117, -116, -116, -115, + -114, -113, -113, -112, -111, -110, -109, -108, + -107, -106, -105, -104, -103, -102, -100, -99, + -98, -97, -95, -94, -93, -91, -90, -88, + -87, -85, -84, -82, -80, -79, -77, -76, + -74, -72, -70, -69, -67, -65, -63, -61, + -60, -58, -56, -54, -52, -50, -48, -46, + -44, -42, -40, -38, -36, -34, -32, -30, + -28, -26, -24, -22, -19, -17, -15, -13, + -11, -9, -7, -5, -2, 0, 1, 3, + 5, 7, 9, 12, 14, 16, 18, 20, + 22, 24, 26, 28, 31, 33, 35, 37, + 39, 41, 43, 45, 47, 49, 51, 53, + 54, 56, 58, 60, 62, 64, 66, 67, + 69, 71, 73, 74, 76, 78, 79, 81, + 83, 84, 86, 87, 89, 90, 92, 93, + 94, 96, 97, 98, 99, 101, 102, 103, + 104, 105, 106, 107, 108, 109, 110, 111, 112 +}; + +static const int hsv_blue_y[] = { + -11, -13, -15, -17, -19, -21, -23, -25, + -27, -29, -31, -33, -35, -37, -39, -41, + -43, -45, -46, -48, -50, -52, -54, -55, + -57, -59, -61, -62, -64, -66, -67, -69, + -71, -72, -74, -75, -77, -78, -80, -81, + -83, -84, -86, -87, -88, -90, -91, -92, + -93, -95, -96, -97, -98, -99, -100, -101, + -102, -103, -104, -105, -106, -106, -107, -108, + -109, -109, -110, -111, -111, -112, -112, -113, + -113, -114, -114, -114, -115, -115, -115, -115, + -116, -116, -116, -116, -116, -116, -116, -116, + -116, -115, -115, -115, -115, -114, -114, -114, + -113, -113, -112, -112, -111, -111, -110, -110, + -109, -108, -108, -107, -106, -105, -104, -103, + -102, -101, -100, -99, -98, -97, -96, -95, + -94, -93, -91, -90, -89, -88, -86, -85, + -84, -82, -81, -79, -78, -76, -75, -73, + -71, -70, -68, -67, -65, -63, -62, -60, + -58, -56, -55, -53, -51, -49, -47, -45, + -44, -42, -40, -38, -36, -34, -32, -30, + -28, -26, -24, -22, -20, -18, -16, -14, + -12, -10, -8, -6, -4, -2, 0, 1, + 3, 5, 7, 9, 11, 13, 15, 17, + 19, 21, 23, 25, 27, 29, 31, 33, + 35, 37, 39, 41, 43, 45, 46, 48, + 50, 52, 54, 55, 57, 59, 61, 62, + 64, 66, 67, 69, 71, 72, 74, 75, + 77, 78, 80, 81, 83, 84, 86, 87, + 88, 90, 91, 92, 93, 95, 96, 97, + 98, 99, 100, 101, 102, 103, 104, 105, + 106, 106, 107, 108, 109, 109, 110, 111, + 111, 112, 112, 113, 113, 114, 114, 114, + 115, 115, 115, 115, 116, 116, 116, 116, + 116, 116, 116, 116, 116, 115, 115, 115, + 115, 114, 114, 114, 113, 113, 112, 112, + 111, 111, 110, 110, 109, 108, 108, 107, + 106, 105, 104, 103, 102, 101, 100, 99, + 98, 97, 96, 95, 94, 93, 91, 90, + 89, 88, 86, 85, 84, 82, 81, 79, + 78, 76, 75, 73, 71, 70, 68, 67, + 65, 63, 62, 60, 58, 56, 55, 53, + 51, 49, 47, 45, 44, 42, 40, 38, + 36, 34, 32, 30, 28, 26, 24, 22, + 20, 18, 16, 14, 12, 10, 8, 6, + 4, 2, 0, -1, -3, -5, -7, -9, -11 +}; + +static u16 i2c_ident[] = { + V4L2_IDENT_OV9650, + V4L2_IDENT_OV9655, + V4L2_IDENT_SOI968, + V4L2_IDENT_OV7660, + V4L2_IDENT_OV7670, + V4L2_IDENT_MT9V011, + V4L2_IDENT_MT9V111, + V4L2_IDENT_MT9V112, + V4L2_IDENT_MT9M001C12ST, + V4L2_IDENT_MT9M111, + V4L2_IDENT_HV7131R, +}; + +static u16 bridge_init[][2] = { + {0x1000, 0x78}, {0x1001, 0x40}, {0x1002, 0x1c}, + {0x1020, 0x80}, {0x1061, 0x01}, {0x1067, 0x40}, + {0x1068, 0x30}, {0x1069, 0x20}, {0x106a, 0x10}, + {0x106b, 0x08}, {0x1188, 0x87}, {0x11a1, 0x00}, + {0x11a2, 0x00}, {0x11a3, 0x6a}, {0x11a4, 0x50}, + {0x11ab, 0x00}, {0x11ac, 0x00}, {0x11ad, 0x50}, + {0x11ae, 0x3c}, {0x118a, 0x04}, {0x0395, 0x04}, + {0x11b8, 0x3a}, {0x118b, 0x0e}, {0x10f7, 0x05}, + {0x10f8, 0x14}, {0x10fa, 0xff}, {0x10f9, 0x00}, + {0x11ba, 0x0a}, {0x11a5, 0x2d}, {0x11a6, 0x2d}, + {0x11a7, 0x3a}, {0x11a8, 0x05}, {0x11a9, 0x04}, + {0x11aa, 0x3f}, {0x11af, 0x28}, {0x11b0, 0xd8}, + {0x11b1, 0x14}, {0x11b2, 0xec}, {0x11b3, 0x32}, + {0x11b4, 0xdd}, {0x11b5, 0x32}, {0x11b6, 0xdd}, + {0x10e0, 0x2c}, {0x11bc, 0x40}, {0x11bd, 0x01}, + {0x11be, 0xf0}, {0x11bf, 0x00}, {0x118c, 0x1f}, + {0x118d, 0x1f}, {0x118e, 0x1f}, {0x118f, 0x1f}, + {0x1180, 0x01}, {0x1181, 0x00}, {0x1182, 0x01}, + {0x1183, 0x00}, {0x1184, 0x50}, {0x1185, 0x80} +}; + +/* Gain = (bit[3:0] / 16 + 1) * (bit[4] + 1) * (bit[5] + 1) * (bit[6] + 1) */ +static u8 ov_gain[] = { + 0x00 /* 1x */, 0x04 /* 1.25x */, 0x08 /* 1.5x */, 0x0c /* 1.75x */, + 0x10 /* 2x */, 0x12 /* 2.25x */, 0x14 /* 2.5x */, 0x16 /* 2.75x */, + 0x18 /* 3x */, 0x1a /* 3.25x */, 0x1c /* 3.5x */, 0x1e /* 3.75x */, + 0x30 /* 4x */, 0x31 /* 4.25x */, 0x32 /* 4.5x */, 0x33 /* 4.75x */, + 0x34 /* 5x */, 0x35 /* 5.25x */, 0x36 /* 5.5x */, 0x37 /* 5.75x */, + 0x38 /* 6x */, 0x39 /* 6.25x */, 0x3a /* 6.5x */, 0x3b /* 6.75x */, + 0x3c /* 7x */, 0x3d /* 7.25x */, 0x3e /* 7.5x */, 0x3f /* 7.75x */, + 0x70 /* 8x */ +}; + +/* Gain = (bit[8] + 1) * (bit[7] + 1) * (bit[6:0] * 0.03125) */ +static u16 micron1_gain[] = { + /* 1x 1.25x 1.5x 1.75x */ + 0x0020, 0x0028, 0x0030, 0x0038, + /* 2x 2.25x 2.5x 2.75x */ + 0x00a0, 0x00a4, 0x00a8, 0x00ac, + /* 3x 3.25x 3.5x 3.75x */ + 0x00b0, 0x00b4, 0x00b8, 0x00bc, + /* 4x 4.25x 4.5x 4.75x */ + 0x00c0, 0x00c4, 0x00c8, 0x00cc, + /* 5x 5.25x 5.5x 5.75x */ + 0x00d0, 0x00d4, 0x00d8, 0x00dc, + /* 6x 6.25x 6.5x 6.75x */ + 0x00e0, 0x00e4, 0x00e8, 0x00ec, + /* 7x 7.25x 7.5x 7.75x */ + 0x00f0, 0x00f4, 0x00f8, 0x00fc, + /* 8x */ + 0x01c0 +}; + +/* mt9m001 sensor uses a different gain formula then other micron sensors */ +/* Gain = (bit[6] + 1) * (bit[5-0] * 0.125) */ +static u16 micron2_gain[] = { + /* 1x 1.25x 1.5x 1.75x */ + 0x0008, 0x000a, 0x000c, 0x000e, + /* 2x 2.25x 2.5x 2.75x */ + 0x0010, 0x0012, 0x0014, 0x0016, + /* 3x 3.25x 3.5x 3.75x */ + 0x0018, 0x001a, 0x001c, 0x001e, + /* 4x 4.25x 4.5x 4.75x */ + 0x0020, 0x0051, 0x0052, 0x0053, + /* 5x 5.25x 5.5x 5.75x */ + 0x0054, 0x0055, 0x0056, 0x0057, + /* 6x 6.25x 6.5x 6.75x */ + 0x0058, 0x0059, 0x005a, 0x005b, + /* 7x 7.25x 7.5x 7.75x */ + 0x005c, 0x005d, 0x005e, 0x005f, + /* 8x */ + 0x0060 +}; + +/* Gain = .5 + bit[7:0] / 16 */ +static u8 hv7131r_gain[] = { + 0x08 /* 1x */, 0x0c /* 1.25x */, 0x10 /* 1.5x */, 0x14 /* 1.75x */, + 0x18 /* 2x */, 0x1c /* 2.25x */, 0x20 /* 2.5x */, 0x24 /* 2.75x */, + 0x28 /* 3x */, 0x2c /* 3.25x */, 0x30 /* 3.5x */, 0x34 /* 3.75x */, + 0x38 /* 4x */, 0x3c /* 4.25x */, 0x40 /* 4.5x */, 0x44 /* 4.75x */, + 0x48 /* 5x */, 0x4c /* 5.25x */, 0x50 /* 5.5x */, 0x54 /* 5.75x */, + 0x58 /* 6x */, 0x5c /* 6.25x */, 0x60 /* 6.5x */, 0x64 /* 6.75x */, + 0x68 /* 7x */, 0x6c /* 7.25x */, 0x70 /* 7.5x */, 0x74 /* 7.75x */, + 0x78 /* 8x */ +}; + +static u8 soi968_init[][2] = { + {0x12, 0x80}, {0x0c, 0x00}, {0x0f, 0x1f}, + {0x11, 0x80}, {0x38, 0x52}, {0x1e, 0x00}, + {0x33, 0x08}, {0x35, 0x8c}, {0x36, 0x0c}, + {0x37, 0x04}, {0x45, 0x04}, {0x47, 0xff}, + {0x3e, 0x00}, {0x3f, 0x00}, {0x3b, 0x20}, + {0x3a, 0x96}, {0x3d, 0x0a}, {0x14, 0x8e}, + {0x13, 0x8a}, {0x12, 0x40}, {0x17, 0x13}, + {0x18, 0x63}, {0x19, 0x01}, {0x1a, 0x79}, + {0x32, 0x24}, {0x03, 0x00}, {0x11, 0x40}, + {0x2a, 0x10}, {0x2b, 0xe0}, {0x10, 0x32}, + {0x00, 0x00}, {0x01, 0x80}, {0x02, 0x80}, +}; + +static u8 ov7660_init[][2] = { + {0x0e, 0x80}, {0x0d, 0x08}, {0x0f, 0xc3}, + {0x04, 0xc3}, {0x10, 0x40}, {0x11, 0x40}, + {0x12, 0x05}, {0x13, 0xba}, {0x14, 0x2a}, + {0x37, 0x0f}, {0x38, 0x02}, {0x39, 0x43}, + {0x3a, 0x00}, {0x69, 0x90}, {0x2d, 0xf6}, + {0x2e, 0x0b}, {0x01, 0x78}, {0x02, 0x50}, +}; + +static u8 ov7670_init[][2] = { + {0x12, 0x80}, {0x11, 0x80}, {0x3a, 0x04}, {0x12, 0x01}, + {0x32, 0xb6}, {0x03, 0x0a}, {0x0c, 0x00}, {0x3e, 0x00}, + {0x70, 0x3a}, {0x71, 0x35}, {0x72, 0x11}, {0x73, 0xf0}, + {0xa2, 0x02}, {0x13, 0xe0}, {0x00, 0x00}, {0x10, 0x00}, + {0x0d, 0x40}, {0x14, 0x28}, {0xa5, 0x05}, {0xab, 0x07}, + {0x24, 0x95}, {0x25, 0x33}, {0x26, 0xe3}, {0x9f, 0x75}, + {0xa0, 0x65}, {0xa1, 0x0b}, {0xa6, 0xd8}, {0xa7, 0xd8}, + {0xa8, 0xf0}, {0xa9, 0x90}, {0xaa, 0x94}, {0x13, 0xe5}, + {0x0e, 0x61}, {0x0f, 0x4b}, {0x16, 0x02}, {0x1e, 0x27}, + {0x21, 0x02}, {0x22, 0x91}, {0x29, 0x07}, {0x33, 0x0b}, + {0x35, 0x0b}, {0x37, 0x1d}, {0x38, 0x71}, {0x39, 0x2a}, + {0x3c, 0x78}, {0x4d, 0x40}, {0x4e, 0x20}, {0x69, 0x00}, + {0x74, 0x19}, {0x8d, 0x4f}, {0x8e, 0x00}, {0x8f, 0x00}, + {0x90, 0x00}, {0x91, 0x00}, {0x96, 0x00}, {0x9a, 0x80}, + {0xb0, 0x84}, {0xb1, 0x0c}, {0xb2, 0x0e}, {0xb3, 0x82}, + {0xb8, 0x0a}, {0x43, 0x0a}, {0x44, 0xf0}, {0x45, 0x20}, + {0x46, 0x7d}, {0x47, 0x29}, {0x48, 0x4a}, {0x59, 0x8c}, + {0x5a, 0xa5}, {0x5b, 0xde}, {0x5c, 0x96}, {0x5d, 0x66}, + {0x5e, 0x10}, {0x6c, 0x0a}, {0x6d, 0x55}, {0x6e, 0x11}, + {0x6f, 0x9e}, {0x6a, 0x40}, {0x01, 0x40}, {0x02, 0x40}, + {0x13, 0xe7}, {0x4f, 0x6e}, {0x50, 0x70}, {0x51, 0x02}, + {0x52, 0x1d}, {0x53, 0x56}, {0x54, 0x73}, {0x55, 0x0a}, + {0x56, 0x55}, {0x57, 0x80}, {0x58, 0x9e}, {0x41, 0x08}, + {0x3f, 0x02}, {0x75, 0x03}, {0x76, 0x63}, {0x4c, 0x04}, + {0x77, 0x06}, {0x3d, 0x02}, {0x4b, 0x09}, {0xc9, 0x30}, + {0x41, 0x08}, {0x56, 0x48}, {0x34, 0x11}, {0xa4, 0x88}, + {0x96, 0x00}, {0x97, 0x30}, {0x98, 0x20}, {0x99, 0x30}, + {0x9a, 0x84}, {0x9b, 0x29}, {0x9c, 0x03}, {0x9d, 0x99}, + {0x9e, 0x7f}, {0x78, 0x04}, {0x79, 0x01}, {0xc8, 0xf0}, + {0x79, 0x0f}, {0xc8, 0x00}, {0x79, 0x10}, {0xc8, 0x7e}, + {0x79, 0x0a}, {0xc8, 0x80}, {0x79, 0x0b}, {0xc8, 0x01}, + {0x79, 0x0c}, {0xc8, 0x0f}, {0x79, 0x0d}, {0xc8, 0x20}, + {0x79, 0x09}, {0xc8, 0x80}, {0x79, 0x02}, {0xc8, 0xc0}, + {0x79, 0x03}, {0xc8, 0x40}, {0x79, 0x05}, {0xc8, 0x30}, + {0x79, 0x26}, {0x62, 0x20}, {0x63, 0x00}, {0x64, 0x06}, + {0x65, 0x00}, {0x66, 0x05}, {0x94, 0x05}, {0x95, 0x0a}, + {0x17, 0x13}, {0x18, 0x01}, {0x19, 0x02}, {0x1a, 0x7a}, + {0x46, 0x59}, {0x47, 0x30}, {0x58, 0x9a}, {0x59, 0x84}, + {0x5a, 0x91}, {0x5b, 0x57}, {0x5c, 0x75}, {0x5d, 0x6d}, + {0x5e, 0x13}, {0x64, 0x07}, {0x94, 0x07}, {0x95, 0x0d}, + {0xa6, 0xdf}, {0xa7, 0xdf}, {0x48, 0x4d}, {0x51, 0x00}, + {0x6b, 0x0a}, {0x11, 0x80}, {0x2a, 0x00}, {0x2b, 0x00}, + {0x92, 0x00}, {0x93, 0x00}, {0x55, 0x0a}, {0x56, 0x60}, + {0x4f, 0x6e}, {0x50, 0x70}, {0x51, 0x00}, {0x52, 0x1d}, + {0x53, 0x56}, {0x54, 0x73}, {0x58, 0x9a}, {0x4f, 0x6e}, + {0x50, 0x70}, {0x51, 0x00}, {0x52, 0x1d}, {0x53, 0x56}, + {0x54, 0x73}, {0x58, 0x9a}, {0x3f, 0x01}, {0x7b, 0x03}, + {0x7c, 0x09}, {0x7d, 0x16}, {0x7e, 0x38}, {0x7f, 0x47}, + {0x80, 0x53}, {0x81, 0x5e}, {0x82, 0x6a}, {0x83, 0x74}, + {0x84, 0x80}, {0x85, 0x8c}, {0x86, 0x9b}, {0x87, 0xb2}, + {0x88, 0xcc}, {0x89, 0xe5}, {0x7a, 0x24}, {0x3b, 0x00}, + {0x9f, 0x76}, {0xa0, 0x65}, {0x13, 0xe2}, {0x6b, 0x0a}, + {0x11, 0x80}, {0x2a, 0x00}, {0x2b, 0x00}, {0x92, 0x00}, + {0x93, 0x00}, +}; + +static u8 ov9650_init[][2] = { + {0x12, 0x80}, {0x00, 0x00}, {0x01, 0x78}, + {0x02, 0x78}, {0x03, 0x36}, {0x04, 0x03}, + {0x05, 0x00}, {0x06, 0x00}, {0x08, 0x00}, + {0x09, 0x01}, {0x0c, 0x00}, {0x0d, 0x00}, + {0x0e, 0xa0}, {0x0f, 0x52}, {0x10, 0x7c}, + {0x11, 0x80}, {0x12, 0x45}, {0x13, 0xc2}, + {0x14, 0x2e}, {0x15, 0x00}, {0x16, 0x07}, + {0x17, 0x24}, {0x18, 0xc5}, {0x19, 0x00}, + {0x1a, 0x3c}, {0x1b, 0x00}, {0x1e, 0x04}, + {0x1f, 0x00}, {0x24, 0x78}, {0x25, 0x68}, + {0x26, 0xd4}, {0x27, 0x80}, {0x28, 0x80}, + {0x29, 0x30}, {0x2a, 0x00}, {0x2b, 0x00}, + {0x2c, 0x80}, {0x2d, 0x00}, {0x2e, 0x00}, + {0x2f, 0x00}, {0x30, 0x08}, {0x31, 0x30}, + {0x32, 0x84}, {0x33, 0xe2}, {0x34, 0xbf}, + {0x35, 0x81}, {0x36, 0xf9}, {0x37, 0x00}, + {0x38, 0x93}, {0x39, 0x50}, {0x3a, 0x01}, + {0x3b, 0x01}, {0x3c, 0x73}, {0x3d, 0x19}, + {0x3e, 0x0b}, {0x3f, 0x80}, {0x40, 0xc1}, + {0x41, 0x00}, {0x42, 0x08}, {0x67, 0x80}, + {0x68, 0x80}, {0x69, 0x40}, {0x6a, 0x00}, + {0x6b, 0x0a}, {0x8b, 0x06}, {0x8c, 0x20}, + {0x8d, 0x00}, {0x8e, 0x00}, {0x8f, 0xdf}, + {0x92, 0x00}, {0x93, 0x00}, {0x94, 0x88}, + {0x95, 0x88}, {0x96, 0x04}, {0xa1, 0x00}, + {0xa5, 0x80}, {0xa8, 0x80}, {0xa9, 0xb8}, + {0xaa, 0x92}, {0xab, 0x0a}, +}; + +static u8 ov9655_init[][2] = { + {0x12, 0x80}, {0x12, 0x01}, {0x0d, 0x00}, {0x0e, 0x61}, + {0x11, 0x80}, {0x13, 0xba}, {0x14, 0x2e}, {0x16, 0x24}, + {0x1e, 0x04}, {0x1e, 0x04}, {0x1e, 0x04}, {0x27, 0x08}, + {0x28, 0x08}, {0x29, 0x15}, {0x2c, 0x08}, {0x32, 0xbf}, + {0x34, 0x3d}, {0x35, 0x00}, {0x36, 0xf8}, {0x38, 0x12}, + {0x39, 0x57}, {0x3a, 0x00}, {0x3b, 0xcc}, {0x3c, 0x0c}, + {0x3d, 0x19}, {0x3e, 0x0c}, {0x3f, 0x01}, {0x41, 0x40}, + {0x42, 0x80}, {0x45, 0x46}, {0x46, 0x62}, {0x47, 0x2a}, + {0x48, 0x3c}, {0x4a, 0xf0}, {0x4b, 0xdc}, {0x4c, 0xdc}, + {0x4d, 0xdc}, {0x4e, 0xdc}, {0x69, 0x02}, {0x6c, 0x04}, + {0x6f, 0x9e}, {0x70, 0x05}, {0x71, 0x78}, {0x77, 0x02}, + {0x8a, 0x23}, {0x8c, 0x0d}, {0x90, 0x7e}, {0x91, 0x7c}, + {0x9f, 0x6e}, {0xa0, 0x6e}, {0xa5, 0x68}, {0xa6, 0x60}, + {0xa8, 0xc1}, {0xa9, 0xfa}, {0xaa, 0x92}, {0xab, 0x04}, + {0xac, 0x80}, {0xad, 0x80}, {0xae, 0x80}, {0xaf, 0x80}, + {0xb2, 0xf2}, {0xb3, 0x20}, {0xb5, 0x00}, {0xb6, 0xaf}, + {0xbb, 0xae}, {0xbc, 0x44}, {0xbd, 0x44}, {0xbe, 0x3b}, + {0xbf, 0x3a}, {0xc0, 0xe2}, {0xc1, 0xc8}, {0xc2, 0x01}, + {0xc4, 0x00}, {0xc6, 0x85}, {0xc7, 0x81}, {0xc9, 0xe0}, + {0xca, 0xe8}, {0xcc, 0xd8}, {0xcd, 0x93}, {0x12, 0x61}, + {0x36, 0xfa}, {0x8c, 0x8d}, {0xc0, 0xaa}, {0x69, 0x0a}, + {0x03, 0x12}, {0x17, 0x14}, {0x18, 0x00}, {0x19, 0x01}, + {0x1a, 0x3d}, {0x32, 0xbf}, {0x11, 0x80}, {0x2a, 0x10}, + {0x2b, 0x0a}, {0x92, 0x00}, {0x93, 0x00}, {0x1e, 0x04}, + {0x1e, 0x04}, {0x10, 0x7c}, {0x04, 0x03}, {0xa1, 0x00}, + {0x2d, 0x00}, {0x2e, 0x00}, {0x00, 0x00}, {0x01, 0x80}, + {0x02, 0x80}, {0x12, 0x61}, {0x36, 0xfa}, {0x8c, 0x8d}, + {0xc0, 0xaa}, {0x69, 0x0a}, {0x03, 0x12}, {0x17, 0x14}, + {0x18, 0x00}, {0x19, 0x01}, {0x1a, 0x3d}, {0x32, 0xbf}, + {0x11, 0x80}, {0x2a, 0x10}, {0x2b, 0x0a}, {0x92, 0x00}, + {0x93, 0x00}, {0x04, 0x01}, {0x10, 0x1f}, {0xa1, 0x00}, + {0x00, 0x0a}, {0xa1, 0x00}, {0x10, 0x5d}, {0x04, 0x03}, + {0x00, 0x01}, {0xa1, 0x00}, {0x10, 0x7c}, {0x04, 0x03}, + {0x00, 0x03}, {0x00, 0x0a}, {0x00, 0x10}, {0x00, 0x13}, +}; + +static u16 mt9v112_init[][2] = { + {0xf0, 0x0000}, {0x0d, 0x0021}, {0x0d, 0x0020}, + {0x34, 0xc019}, {0x0a, 0x0011}, {0x0b, 0x000b}, + {0x20, 0x0703}, {0x35, 0x2022}, {0xf0, 0x0001}, + {0x05, 0x0000}, {0x06, 0x340c}, {0x3b, 0x042a}, + {0x3c, 0x0400}, {0xf0, 0x0002}, {0x2e, 0x0c58}, + {0x5b, 0x0001}, {0xc8, 0x9f0b}, {0xf0, 0x0001}, + {0x9b, 0x5300}, {0xf0, 0x0000}, {0x2b, 0x0020}, + {0x2c, 0x002a}, {0x2d, 0x0032}, {0x2e, 0x0020}, + {0x09, 0x01dc}, {0x01, 0x000c}, {0x02, 0x0020}, + {0x03, 0x01e0}, {0x04, 0x0280}, {0x06, 0x000c}, + {0x05, 0x0098}, {0x20, 0x0703}, {0x09, 0x01f2}, + {0x2b, 0x00a0}, {0x2c, 0x00a0}, {0x2d, 0x00a0}, + {0x2e, 0x00a0}, {0x01, 0x000c}, {0x02, 0x0020}, + {0x03, 0x01e0}, {0x04, 0x0280}, {0x06, 0x000c}, + {0x05, 0x0098}, {0x09, 0x01c1}, {0x2b, 0x00ae}, + {0x2c, 0x00ae}, {0x2d, 0x00ae}, {0x2e, 0x00ae}, +}; + +static u16 mt9v111_init[][2] = { + {0x01, 0x0004}, {0x0d, 0x0001}, {0x0d, 0x0000}, + {0x01, 0x0001}, {0x02, 0x0016}, {0x03, 0x01e1}, + {0x04, 0x0281}, {0x05, 0x0004}, {0x07, 0x3002}, + {0x21, 0x0000}, {0x25, 0x4024}, {0x26, 0xff03}, + {0x27, 0xff10}, {0x2b, 0x7828}, {0x2c, 0xb43c}, + {0x2d, 0xf0a0}, {0x2e, 0x0c64}, {0x2f, 0x0064}, + {0x67, 0x4010}, {0x06, 0x301e}, {0x08, 0x0480}, + {0x01, 0x0004}, {0x02, 0x0016}, {0x03, 0x01e6}, + {0x04, 0x0286}, {0x05, 0x0004}, {0x06, 0x0000}, + {0x07, 0x3002}, {0x08, 0x0008}, {0x0c, 0x0000}, + {0x0d, 0x0000}, {0x0e, 0x0000}, {0x0f, 0x0000}, + {0x10, 0x0000}, {0x11, 0x0000}, {0x12, 0x00b0}, + {0x13, 0x007c}, {0x14, 0x0000}, {0x15, 0x0000}, + {0x16, 0x0000}, {0x17, 0x0000}, {0x18, 0x0000}, + {0x19, 0x0000}, {0x1a, 0x0000}, {0x1b, 0x0000}, + {0x1c, 0x0000}, {0x1d, 0x0000}, {0x30, 0x0000}, + {0x30, 0x0005}, {0x31, 0x0000}, {0x02, 0x0016}, + {0x03, 0x01e1}, {0x04, 0x0281}, {0x05, 0x0004}, + {0x06, 0x0000}, {0x07, 0x3002}, {0x06, 0x002d}, + {0x05, 0x0004}, {0x09, 0x0064}, {0x2b, 0x00a0}, + {0x2c, 0x00a0}, {0x2d, 0x00a0}, {0x2e, 0x00a0}, + {0x02, 0x0016}, {0x03, 0x01e1}, {0x04, 0x0281}, + {0x05, 0x0004}, {0x06, 0x002d}, {0x07, 0x3002}, + {0x0e, 0x0008}, {0x06, 0x002d}, {0x05, 0x0004}, +}; + +static u16 mt9v011_init[][2] = { + {0x07, 0x0002}, {0x0d, 0x0001}, {0x0d, 0x0000}, + {0x01, 0x0008}, {0x02, 0x0016}, {0x03, 0x01e1}, + {0x04, 0x0281}, {0x05, 0x0083}, {0x06, 0x0006}, + {0x0d, 0x0002}, {0x0a, 0x0000}, {0x0b, 0x0000}, + {0x0c, 0x0000}, {0x0d, 0x0000}, {0x0e, 0x0000}, + {0x0f, 0x0000}, {0x10, 0x0000}, {0x11, 0x0000}, + {0x12, 0x0000}, {0x13, 0x0000}, {0x14, 0x0000}, + {0x15, 0x0000}, {0x16, 0x0000}, {0x17, 0x0000}, + {0x18, 0x0000}, {0x19, 0x0000}, {0x1a, 0x0000}, + {0x1b, 0x0000}, {0x1c, 0x0000}, {0x1d, 0x0000}, + {0x32, 0x0000}, {0x20, 0x1101}, {0x21, 0x0000}, + {0x22, 0x0000}, {0x23, 0x0000}, {0x24, 0x0000}, + {0x25, 0x0000}, {0x26, 0x0000}, {0x27, 0x0024}, + {0x2f, 0xf7b0}, {0x30, 0x0005}, {0x31, 0x0000}, + {0x32, 0x0000}, {0x33, 0x0000}, {0x34, 0x0100}, + {0x3d, 0x068f}, {0x40, 0x01e0}, {0x41, 0x00d1}, + {0x44, 0x0082}, {0x5a, 0x0000}, {0x5b, 0x0000}, + {0x5c, 0x0000}, {0x5d, 0x0000}, {0x5e, 0x0000}, + {0x5f, 0xa31d}, {0x62, 0x0611}, {0x0a, 0x0000}, + {0x06, 0x0029}, {0x05, 0x0009}, {0x20, 0x1101}, + {0x20, 0x1101}, {0x09, 0x0064}, {0x07, 0x0003}, + {0x2b, 0x0033}, {0x2c, 0x00a0}, {0x2d, 0x00a0}, + {0x2e, 0x0033}, {0x07, 0x0002}, {0x06, 0x0000}, + {0x06, 0x0029}, {0x05, 0x0009}, +}; + +static u16 mt9m001_init[][2] = { + {0x0d, 0x0001}, {0x0d, 0x0000}, {0x01, 0x000e}, + {0x02, 0x0014}, {0x03, 0x03c1}, {0x04, 0x0501}, + {0x05, 0x0083}, {0x06, 0x0006}, {0x0d, 0x0002}, + {0x0a, 0x0000}, {0x0c, 0x0000}, {0x11, 0x0000}, + {0x1e, 0x8000}, {0x5f, 0x8904}, {0x60, 0x0000}, + {0x61, 0x0000}, {0x62, 0x0498}, {0x63, 0x0000}, + {0x64, 0x0000}, {0x20, 0x111d}, {0x06, 0x00f2}, + {0x05, 0x0013}, {0x09, 0x10f2}, {0x07, 0x0003}, + {0x2b, 0x002a}, {0x2d, 0x002a}, {0x2c, 0x002a}, + {0x2e, 0x0029}, {0x07, 0x0002}, +}; + +static u16 mt9m111_init[][2] = { + {0xf0, 0x0000}, {0x0d, 0x0008}, {0x0d, 0x0009}, + {0x0d, 0x0008}, {0xf0, 0x0001}, {0x3a, 0x4300}, + {0x9b, 0x4300}, {0xa1, 0x0280}, {0xa4, 0x0200}, + {0x06, 0x308e}, {0xf0, 0x0000}, +}; + +static u8 hv7131r_init[][2] = { + {0x02, 0x08}, {0x02, 0x00}, {0x01, 0x08}, + {0x02, 0x00}, {0x20, 0x00}, {0x21, 0xd0}, + {0x22, 0x00}, {0x23, 0x09}, {0x01, 0x08}, + {0x01, 0x08}, {0x01, 0x08}, {0x25, 0x07}, + {0x26, 0xc3}, {0x27, 0x50}, {0x30, 0x62}, + {0x31, 0x10}, {0x32, 0x06}, {0x33, 0x10}, + {0x20, 0x00}, {0x21, 0xd0}, {0x22, 0x00}, + {0x23, 0x09}, {0x01, 0x08}, +}; + +int reg_r(struct gspca_dev *gspca_dev, u16 reg, u16 length) +{ + struct usb_device *dev = gspca_dev->dev; + int result; + result = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), + 0x00, + USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_INTERFACE, + reg, + 0x00, + gspca_dev->usb_buf, + length, + 500); + if (unlikely(result < 0 || result != length)) { + err("Read register failed 0x%02X", reg); + return -EIO; + } + return 0; +} + +int reg_w(struct gspca_dev *gspca_dev, u16 reg, const u8 *buffer, int length) +{ + struct usb_device *dev = gspca_dev->dev; + int result; + memcpy(gspca_dev->usb_buf, buffer, length); + result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), + 0x08, + USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_INTERFACE, + reg, + 0x00, + gspca_dev->usb_buf, + length, + 500); + if (unlikely(result < 0 || result != length)) { + err("Write register failed index 0x%02X", reg); + return -EIO; + } + return 0; +} + +int reg_w1(struct gspca_dev *gspca_dev, u16 reg, const u8 value) +{ + u8 data[1] = {value}; + return reg_w(gspca_dev, reg, data, 1); +} + +int i2c_w(struct gspca_dev *gspca_dev, const u8 *buffer) +{ + int i; + reg_w(gspca_dev, 0x10c0, buffer, 8); + for (i = 0; i < 5; i++) { + reg_r(gspca_dev, 0x10c0, 1); + if (gspca_dev->usb_buf[0] & 0x04) { + if (gspca_dev->usb_buf[0] & 0x08) + return -1; + return 0; + } + msleep(1); + } + return -1; +} + +int i2c_w1(struct gspca_dev *gspca_dev, u8 reg, u8 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + u8 row[8]; + + /* + * from the point of view of the bridge, the length + * includes the address + */ + row[0] = 0x81 | (2 << 4); + row[1] = sd->i2c_addr; + row[2] = reg; + row[3] = val; + row[4] = 0x00; + row[5] = 0x00; + row[6] = 0x00; + row[7] = 0x10; + + return i2c_w(gspca_dev, row); +} + +int i2c_w2(struct gspca_dev *gspca_dev, u8 reg, u16 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + u8 row[8]; + + /* + * from the point of view of the bridge, the length + * includes the address + */ + row[0] = 0x81 | (3 << 4); + row[1] = sd->i2c_addr; + row[2] = reg; + row[3] = (val >> 8) & 0xff; + row[4] = val & 0xff; + row[5] = 0x00; + row[6] = 0x00; + row[7] = 0x10; + + return i2c_w(gspca_dev, row); +} + +int i2c_r1(struct gspca_dev *gspca_dev, u8 reg, u8 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + u8 row[8]; + + row[0] = 0x81 | 0x10; + row[1] = sd->i2c_addr; + row[2] = reg; + row[3] = 0; + row[4] = 0; + row[5] = 0; + row[6] = 0; + row[7] = 0x10; + reg_w(gspca_dev, 0x10c0, row, 8); + msleep(1); + row[0] = 0x81 | (2 << 4) | 0x02; + row[2] = 0; + reg_w(gspca_dev, 0x10c0, row, 8); + msleep(1); + reg_r(gspca_dev, 0x10c2, 5); + *val = gspca_dev->usb_buf[3]; + return 0; +} + +int i2c_r2(struct gspca_dev *gspca_dev, u8 reg, u16 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + u8 row[8]; + + row[0] = 0x81 | 0x10; + row[1] = sd->i2c_addr; + row[2] = reg; + row[3] = 0; + row[4] = 0; + row[5] = 0; + row[6] = 0; + row[7] = 0x10; + reg_w(gspca_dev, 0x10c0, row, 8); + msleep(1); + row[0] = 0x81 | (3 << 4) | 0x02; + row[2] = 0; + reg_w(gspca_dev, 0x10c0, row, 8); + msleep(1); + reg_r(gspca_dev, 0x10c2, 5); + *val = (gspca_dev->usb_buf[2] << 8) | gspca_dev->usb_buf[3]; + return 0; +} + +static int ov9650_init_sensor(struct gspca_dev *gspca_dev) +{ + int i; + struct sd *sd = (struct sd *) gspca_dev; + + for (i = 0; i < ARRAY_SIZE(ov9650_init); i++) { + if (i2c_w1(gspca_dev, ov9650_init[i][0], + ov9650_init[i][1]) < 0) { + err("OV9650 sensor initialization failed"); + return -ENODEV; + } + } + sd->hstart = 1; + sd->vstart = 7; + return 0; +} + +static int ov9655_init_sensor(struct gspca_dev *gspca_dev) +{ + int i; + struct sd *sd = (struct sd *) gspca_dev; + + for (i = 0; i < ARRAY_SIZE(ov9655_init); i++) { + if (i2c_w1(gspca_dev, ov9655_init[i][0], + ov9655_init[i][1]) < 0) { + err("OV9655 sensor initialization failed"); + return -ENODEV; + } + } + /* disable hflip and vflip */ + gspca_dev->ctrl_dis = (1 << HFLIP_IDX) | (1 << VFLIP_IDX); + sd->hstart = 0; + sd->vstart = 7; + return 0; +} + +static int soi968_init_sensor(struct gspca_dev *gspca_dev) +{ + int i; + struct sd *sd = (struct sd *) gspca_dev; + + for (i = 0; i < ARRAY_SIZE(soi968_init); i++) { + if (i2c_w1(gspca_dev, soi968_init[i][0], + soi968_init[i][1]) < 0) { + err("SOI968 sensor initialization failed"); + return -ENODEV; + } + } + /* disable hflip and vflip */ + gspca_dev->ctrl_dis = (1 << HFLIP_IDX) | (1 << VFLIP_IDX); + sd->hstart = 60; + sd->vstart = 11; + return 0; +} + +static int ov7660_init_sensor(struct gspca_dev *gspca_dev) +{ + int i; + struct sd *sd = (struct sd *) gspca_dev; + + for (i = 0; i < ARRAY_SIZE(ov7660_init); i++) { + if (i2c_w1(gspca_dev, ov7660_init[i][0], + ov7660_init[i][1]) < 0) { + err("OV7660 sensor initialization failed"); + return -ENODEV; + } + } + /* disable hflip and vflip */ + gspca_dev->ctrl_dis = (1 << HFLIP_IDX) | (1 << VFLIP_IDX); + sd->hstart = 1; + sd->vstart = 1; + return 0; +} + +static int ov7670_init_sensor(struct gspca_dev *gspca_dev) +{ + int i; + struct sd *sd = (struct sd *) gspca_dev; + + for (i = 0; i < ARRAY_SIZE(ov7670_init); i++) { + if (i2c_w1(gspca_dev, ov7670_init[i][0], + ov7670_init[i][1]) < 0) { + err("OV7670 sensor initialization failed"); + return -ENODEV; + } + } + /* disable hflip and vflip */ + gspca_dev->ctrl_dis = (1 << HFLIP_IDX) | (1 << VFLIP_IDX); + sd->hstart = 0; + sd->vstart = 1; + return 0; +} + +static int mt9v_init_sensor(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + int i; + u16 value; + int ret; + + sd->i2c_addr = 0x5d; + ret = i2c_r2(gspca_dev, 0xff, &value); + if ((ret == 0) && (value == 0x8243)) { + for (i = 0; i < ARRAY_SIZE(mt9v011_init); i++) { + if (i2c_w2(gspca_dev, mt9v011_init[i][0], + mt9v011_init[i][1]) < 0) { + err("MT9V011 sensor initialization failed"); + return -ENODEV; + } + } + sd->hstart = 2; + sd->vstart = 2; + sd->sensor = SENSOR_MT9V011; + info("MT9V011 sensor detected"); + return 0; + } + + sd->i2c_addr = 0x5c; + i2c_w2(gspca_dev, 0x01, 0x0004); + ret = i2c_r2(gspca_dev, 0xff, &value); + if ((ret == 0) && (value == 0x823a)) { + for (i = 0; i < ARRAY_SIZE(mt9v111_init); i++) { + if (i2c_w2(gspca_dev, mt9v111_init[i][0], + mt9v111_init[i][1]) < 0) { + err("MT9V111 sensor initialization failed"); + return -ENODEV; + } + } + sd->hstart = 2; + sd->vstart = 2; + sd->sensor = SENSOR_MT9V111; + info("MT9V111 sensor detected"); + return 0; + } + + sd->i2c_addr = 0x5d; + ret = i2c_w2(gspca_dev, 0xf0, 0x0000); + if (ret < 0) { + sd->i2c_addr = 0x48; + i2c_w2(gspca_dev, 0xf0, 0x0000); + } + ret = i2c_r2(gspca_dev, 0x00, &value); + if ((ret == 0) && (value == 0x1229)) { + for (i = 0; i < ARRAY_SIZE(mt9v112_init); i++) { + if (i2c_w2(gspca_dev, mt9v112_init[i][0], + mt9v112_init[i][1]) < 0) { + err("MT9V112 sensor initialization failed"); + return -ENODEV; + } + } + sd->hstart = 6; + sd->vstart = 2; + sd->sensor = SENSOR_MT9V112; + info("MT9V112 sensor detected"); + return 0; + } + + return -ENODEV; +} + +static int mt9m111_init_sensor(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + int i; + for (i = 0; i < ARRAY_SIZE(mt9m111_init); i++) { + if (i2c_w2(gspca_dev, mt9m111_init[i][0], + mt9m111_init[i][1]) < 0) { + err("MT9M111 sensor initialization failed"); + return -ENODEV; + } + } + sd->hstart = 0; + sd->vstart = 2; + return 0; +} + +static int mt9m001_init_sensor(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + int i; + for (i = 0; i < ARRAY_SIZE(mt9m001_init); i++) { + if (i2c_w2(gspca_dev, mt9m001_init[i][0], + mt9m001_init[i][1]) < 0) { + err("MT9M001 sensor initialization failed"); + return -ENODEV; + } + } + /* disable hflip and vflip */ + gspca_dev->ctrl_dis = (1 << HFLIP_IDX) | (1 << VFLIP_IDX); + sd->hstart = 2; + sd->vstart = 2; + return 0; +} + +static int hv7131r_init_sensor(struct gspca_dev *gspca_dev) +{ + int i; + struct sd *sd = (struct sd *) gspca_dev; + + for (i = 0; i < ARRAY_SIZE(hv7131r_init); i++) { + if (i2c_w1(gspca_dev, hv7131r_init[i][0], + hv7131r_init[i][1]) < 0) { + err("HV7131R Sensor initialization failed"); + return -ENODEV; + } + } + sd->hstart = 0; + sd->vstart = 1; + return 0; +} + +#ifdef CONFIG_USB_GSPCA_SN9C20X_EVDEV +static int input_kthread(void *data) +{ + struct gspca_dev *gspca_dev = (struct gspca_dev *)data; + struct sd *sd = (struct sd *) gspca_dev; + + DECLARE_WAIT_QUEUE_HEAD(wait); + set_freezable(); + for (;;) { + if (kthread_should_stop()) + break; + + if (reg_r(gspca_dev, 0x1005, 1) < 0) + continue; + + input_report_key(sd->input_dev, + KEY_CAMERA, + gspca_dev->usb_buf[0] & sd->input_gpio); + input_sync(sd->input_dev); + + wait_event_freezable_timeout(wait, + kthread_should_stop(), + msecs_to_jiffies(100)); + } + return 0; +} + + +static int sn9c20x_input_init(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + if (sd->input_gpio == 0) + return 0; + + sd->input_dev = input_allocate_device(); + if (!sd->input_dev) + return -ENOMEM; + + sd->input_dev->name = "SN9C20X Webcam"; + + sd->input_dev->phys = kasprintf(GFP_KERNEL, "usb-%s-%s", + gspca_dev->dev->bus->bus_name, + gspca_dev->dev->devpath); + + if (!sd->input_dev->phys) + return -ENOMEM; + + usb_to_input_id(gspca_dev->dev, &sd->input_dev->id); + sd->input_dev->dev.parent = &gspca_dev->dev->dev; + + set_bit(EV_KEY, sd->input_dev->evbit); + set_bit(KEY_CAMERA, sd->input_dev->keybit); + + if (input_register_device(sd->input_dev)) + return -EINVAL; + + sd->input_task = kthread_run(input_kthread, gspca_dev, "sn9c20x/%d", + gspca_dev->vdev.minor); + + if (IS_ERR(sd->input_task)) + return -EINVAL; + + return 0; +} + +static void sn9c20x_input_cleanup(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + if (sd->input_task != NULL && !IS_ERR(sd->input_task)) + kthread_stop(sd->input_task); + + if (sd->input_dev != NULL) { + input_unregister_device(sd->input_dev); + kfree(sd->input_dev->phys); + input_free_device(sd->input_dev); + sd->input_dev = NULL; + } +} +#endif + +static int set_cmatrix(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + s32 hue_coord, hue_index = 180 + sd->hue; + u8 cmatrix[21]; + memset(cmatrix, 0, 21); + + cmatrix[2] = (sd->contrast * 0x25 / 0x100) + 0x26; + cmatrix[0] = 0x13 + (cmatrix[2] - 0x26) * 0x13 / 0x25; + cmatrix[4] = 0x07 + (cmatrix[2] - 0x26) * 0x07 / 0x25; + cmatrix[18] = sd->brightness - 0x80; + + hue_coord = (hsv_red_x[hue_index] * sd->saturation) >> 8; + cmatrix[6] = (unsigned char)(hue_coord & 0xff); + cmatrix[7] = (unsigned char)((hue_coord >> 8) & 0x0f); + + hue_coord = (hsv_red_y[hue_index] * sd->saturation) >> 8; + cmatrix[8] = (unsigned char)(hue_coord & 0xff); + cmatrix[9] = (unsigned char)((hue_coord >> 8) & 0x0f); + + hue_coord = (hsv_green_x[hue_index] * sd->saturation) >> 8; + cmatrix[10] = (unsigned char)(hue_coord & 0xff); + cmatrix[11] = (unsigned char)((hue_coord >> 8) & 0x0f); + + hue_coord = (hsv_green_y[hue_index] * sd->saturation) >> 8; + cmatrix[12] = (unsigned char)(hue_coord & 0xff); + cmatrix[13] = (unsigned char)((hue_coord >> 8) & 0x0f); + + hue_coord = (hsv_blue_x[hue_index] * sd->saturation) >> 8; + cmatrix[14] = (unsigned char)(hue_coord & 0xff); + cmatrix[15] = (unsigned char)((hue_coord >> 8) & 0x0f); + + hue_coord = (hsv_blue_y[hue_index] * sd->saturation) >> 8; + cmatrix[16] = (unsigned char)(hue_coord & 0xff); + cmatrix[17] = (unsigned char)((hue_coord >> 8) & 0x0f); + + return reg_w(gspca_dev, 0x10e1, cmatrix, 21); +} + +static int set_gamma(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + u8 gamma[17]; + u8 gval = sd->gamma * 0xb8 / 0x100; + + + gamma[0] = 0x0a; + gamma[1] = 0x13 + (gval * (0xcb - 0x13) / 0xb8); + gamma[2] = 0x25 + (gval * (0xee - 0x25) / 0xb8); + gamma[3] = 0x37 + (gval * (0xfa - 0x37) / 0xb8); + gamma[4] = 0x45 + (gval * (0xfc - 0x45) / 0xb8); + gamma[5] = 0x55 + (gval * (0xfb - 0x55) / 0xb8); + gamma[6] = 0x65 + (gval * (0xfc - 0x65) / 0xb8); + gamma[7] = 0x74 + (gval * (0xfd - 0x74) / 0xb8); + gamma[8] = 0x83 + (gval * (0xfe - 0x83) / 0xb8); + gamma[9] = 0x92 + (gval * (0xfc - 0x92) / 0xb8); + gamma[10] = 0xa1 + (gval * (0xfc - 0xa1) / 0xb8); + gamma[11] = 0xb0 + (gval * (0xfc - 0xb0) / 0xb8); + gamma[12] = 0xbf + (gval * (0xfb - 0xbf) / 0xb8); + gamma[13] = 0xce + (gval * (0xfb - 0xce) / 0xb8); + gamma[14] = 0xdf + (gval * (0xfd - 0xdf) / 0xb8); + gamma[15] = 0xea + (gval * (0xf9 - 0xea) / 0xb8); + gamma[16] = 0xf5; + + return reg_w(gspca_dev, 0x1190, gamma, 17); +} + +static int set_redblue(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + reg_w1(gspca_dev, 0x118c, sd->red); + reg_w1(gspca_dev, 0x118f, sd->blue); + return 0; +} + +static int set_hvflip(struct gspca_dev *gspca_dev) +{ + u8 value, tslb; + u16 value2; + struct sd *sd = (struct sd *) gspca_dev; + switch (sd->sensor) { + case SENSOR_OV9650: + i2c_r1(gspca_dev, 0x1e, &value); + value &= ~0x30; + tslb = 0x01; + if (sd->hflip) + value |= 0x20; + if (sd->vflip) { + value |= 0x10; + tslb = 0x49; + } + i2c_w1(gspca_dev, 0x1e, value); + i2c_w1(gspca_dev, 0x3a, tslb); + break; + case SENSOR_MT9V111: + case SENSOR_MT9V011: + i2c_r2(gspca_dev, 0x20, &value2); + value2 &= ~0xc0a0; + if (sd->hflip) + value2 |= 0x8080; + if (sd->vflip) + value2 |= 0x4020; + i2c_w2(gspca_dev, 0x20, value2); + break; + case SENSOR_MT9M111: + case SENSOR_MT9V112: + i2c_r2(gspca_dev, 0x20, &value2); + value2 &= ~0x0003; + if (sd->hflip) + value2 |= 0x0002; + if (sd->vflip) + value2 |= 0x0001; + i2c_w2(gspca_dev, 0x20, value2); + break; + case SENSOR_HV7131R: + i2c_r1(gspca_dev, 0x01, &value); + value &= ~0x03; + if (sd->vflip) + value |= 0x01; + if (sd->hflip) + value |= 0x02; + i2c_w1(gspca_dev, 0x01, value); + break; + } + return 0; +} + +static int set_exposure(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + u8 exp[8] = {0x81, sd->i2c_addr, 0x00, 0x00, 0x00, 0x00, 0x00, 0x1e}; + switch (sd->sensor) { + case SENSOR_OV7660: + case SENSOR_OV7670: + case SENSOR_SOI968: + case SENSOR_OV9655: + case SENSOR_OV9650: + exp[0] |= (3 << 4); + exp[2] = 0x2d; + exp[3] = sd->exposure & 0xff; + exp[4] = sd->exposure >> 8; + break; + case SENSOR_MT9M001: + case SENSOR_MT9M111: + case SENSOR_MT9V112: + case SENSOR_MT9V111: + case SENSOR_MT9V011: + exp[0] |= (3 << 4); + exp[2] = 0x09; + exp[3] = sd->exposure >> 8; + exp[4] = sd->exposure & 0xff; + break; + case SENSOR_HV7131R: + exp[0] |= (4 << 4); + exp[2] = 0x25; + exp[3] = ((sd->exposure * 0xffffff) / 0xffff) >> 16; + exp[4] = ((sd->exposure * 0xffffff) / 0xffff) >> 8; + exp[5] = ((sd->exposure * 0xffffff) / 0xffff) & 0xff; + break; + } + i2c_w(gspca_dev, exp); + return 0; +} + +static int set_gain(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + u8 gain[8] = {0x81, sd->i2c_addr, 0x00, 0x00, 0x00, 0x00, 0x00, 0x1d}; + switch (sd->sensor) { + case SENSOR_OV7660: + case SENSOR_OV7670: + case SENSOR_SOI968: + case SENSOR_OV9655: + case SENSOR_OV9650: + gain[0] |= (2 << 4); + gain[3] = ov_gain[sd->gain]; + break; + case SENSOR_MT9V011: + case SENSOR_MT9V111: + gain[0] |= (3 << 4); + gain[2] = 0x35; + gain[3] = micron1_gain[sd->gain] >> 8; + gain[4] = micron1_gain[sd->gain] & 0xff; + break; + case SENSOR_MT9V112: + case SENSOR_MT9M111: + gain[0] |= (3 << 4); + gain[2] = 0x2f; + gain[3] = micron1_gain[sd->gain] >> 8; + gain[4] = micron1_gain[sd->gain] & 0xff; + break; + case SENSOR_MT9M001: + gain[0] |= (3 << 4); + gain[2] = 0x2f; + gain[3] = micron2_gain[sd->gain] >> 8; + gain[4] = micron2_gain[sd->gain] & 0xff; + break; + case SENSOR_HV7131R: + gain[0] |= (2 << 4); + gain[2] = 0x30; + gain[3] = hv7131r_gain[sd->gain]; + break; + } + i2c_w(gspca_dev, gain); + return 0; +} + +static int sd_setbrightness(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->brightness = val; + if (gspca_dev->streaming) + return set_cmatrix(gspca_dev); + return 0; +} + +static int sd_getbrightness(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->brightness; + return 0; +} + + +static int sd_setcontrast(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->contrast = val; + if (gspca_dev->streaming) + return set_cmatrix(gspca_dev); + return 0; +} + +static int sd_getcontrast(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->contrast; + return 0; +} + +static int sd_setsaturation(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->saturation = val; + if (gspca_dev->streaming) + return set_cmatrix(gspca_dev); + return 0; +} + +static int sd_getsaturation(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->saturation; + return 0; +} + +static int sd_sethue(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->hue = val; + if (gspca_dev->streaming) + return set_cmatrix(gspca_dev); + return 0; +} + +static int sd_gethue(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->hue; + return 0; +} + +static int sd_setgamma(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->gamma = val; + if (gspca_dev->streaming) + return set_gamma(gspca_dev); + return 0; +} + +static int sd_getgamma(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->gamma; + return 0; +} + +static int sd_setredbalance(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->red = val; + if (gspca_dev->streaming) + return set_redblue(gspca_dev); + return 0; +} + +static int sd_getredbalance(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->red; + return 0; +} + +static int sd_setbluebalance(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->blue = val; + if (gspca_dev->streaming) + return set_redblue(gspca_dev); + return 0; +} + +static int sd_getbluebalance(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->blue; + return 0; +} + +static int sd_sethflip(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->hflip = val; + if (gspca_dev->streaming) + return set_hvflip(gspca_dev); + return 0; +} + +static int sd_gethflip(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->hflip; + return 0; +} + +static int sd_setvflip(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->vflip = val; + if (gspca_dev->streaming) + return set_hvflip(gspca_dev); + return 0; +} + +static int sd_getvflip(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->vflip; + return 0; +} + +static int sd_setexposure(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->exposure = val; + if (gspca_dev->streaming) + return set_exposure(gspca_dev); + return 0; +} + +static int sd_getexposure(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->exposure; + return 0; +} + +static int sd_setgain(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->gain = val; + if (gspca_dev->streaming) + return set_gain(gspca_dev); + return 0; +} + +static int sd_getgain(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->gain; + return 0; +} + +static int sd_setautoexposure(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + sd->auto_exposure = val; + return 0; +} + +static int sd_getautoexposure(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->auto_exposure; + return 0; +} + +#ifdef CONFIG_VIDEO_ADV_DEBUG +static int sd_dbg_g_register(struct gspca_dev *gspca_dev, + struct v4l2_dbg_register *reg) +{ + struct sd *sd = (struct sd *) gspca_dev; + switch (reg->match.type) { + case V4L2_CHIP_MATCH_HOST: + if (reg->match.addr != 0) + return -EINVAL; + if (reg->reg < 0x1000 || reg->reg > 0x11ff) + return -EINVAL; + if (reg_r(gspca_dev, reg->reg, 1) < 0) + return -EINVAL; + reg->val = gspca_dev->usb_buf[0]; + return 0; + case V4L2_CHIP_MATCH_I2C_ADDR: + if (reg->match.addr != sd->i2c_addr) + return -EINVAL; + if (sd->sensor >= SENSOR_MT9V011 && + sd->sensor <= SENSOR_MT9M111) { + if (i2c_r2(gspca_dev, reg->reg, (u16 *)®->val) < 0) + return -EINVAL; + } else { + if (i2c_r1(gspca_dev, reg->reg, (u8 *)®->val) < 0) + return -EINVAL; + } + return 0; + } + return -EINVAL; +} + +static int sd_dbg_s_register(struct gspca_dev *gspca_dev, + struct v4l2_dbg_register *reg) +{ + struct sd *sd = (struct sd *) gspca_dev; + switch (reg->match.type) { + case V4L2_CHIP_MATCH_HOST: + if (reg->match.addr != 0) + return -EINVAL; + if (reg->reg < 0x1000 || reg->reg > 0x11ff) + return -EINVAL; + if (reg_w1(gspca_dev, reg->reg, reg->val) < 0) + return -EINVAL; + return 0; + case V4L2_CHIP_MATCH_I2C_ADDR: + if (reg->match.addr != sd->i2c_addr) + return -EINVAL; + if (sd->sensor >= SENSOR_MT9V011 && + sd->sensor <= SENSOR_MT9M111) { + if (i2c_w2(gspca_dev, reg->reg, reg->val) < 0) + return -EINVAL; + } else { + if (i2c_w1(gspca_dev, reg->reg, reg->val) < 0) + return -EINVAL; + } + return 0; + } + return -EINVAL; +} +#endif + +static int sd_chip_ident(struct gspca_dev *gspca_dev, + struct v4l2_dbg_chip_ident *chip) +{ + struct sd *sd = (struct sd *) gspca_dev; + + switch (chip->match.type) { + case V4L2_CHIP_MATCH_HOST: + if (chip->match.addr != 0) + return -EINVAL; + chip->revision = 0; + chip->ident = V4L2_IDENT_SN9C20X; + return 0; + case V4L2_CHIP_MATCH_I2C_ADDR: + if (chip->match.addr != sd->i2c_addr) + return -EINVAL; + chip->revision = 0; + chip->ident = i2c_ident[sd->sensor]; + return 0; + } + return -EINVAL; +} + +static int sd_config(struct gspca_dev *gspca_dev, + const struct usb_device_id *id) +{ + struct sd *sd = (struct sd *) gspca_dev; + struct cam *cam; + + cam = &gspca_dev->cam; + + sd->sensor = (id->driver_info >> 8) & 0xff; + sd->i2c_addr = id->driver_info & 0xff; + + switch (sd->sensor) { + case SENSOR_OV9650: + cam->cam_mode = sxga_mode; + cam->nmodes = ARRAY_SIZE(sxga_mode); + break; + default: + cam->cam_mode = vga_mode; + cam->nmodes = ARRAY_SIZE(vga_mode); + } + + sd->old_step = 0; + sd->older_step = 0; + sd->exposure_step = 16; + + sd->brightness = BRIGHTNESS_DEFAULT; + sd->contrast = CONTRAST_DEFAULT; + sd->saturation = SATURATION_DEFAULT; + sd->hue = HUE_DEFAULT; + sd->gamma = GAMMA_DEFAULT; + sd->red = RED_DEFAULT; + sd->blue = BLUE_DEFAULT; + + sd->hflip = HFLIP_DEFAULT; + sd->vflip = VFLIP_DEFAULT; + sd->exposure = EXPOSURE_DEFAULT; + sd->gain = GAIN_DEFAULT; + sd->auto_exposure = AUTO_EXPOSURE_DEFAULT; + + sd->quality = 95; + +#ifdef CONFIG_USB_GSPCA_SN9C20X_EVDEV + sd->input_gpio = (id->driver_info >> 16) & 0xff; + if (sn9c20x_input_init(gspca_dev) < 0) + return -ENODEV; +#endif + return 0; +} + +static int sd_init(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + int i; + u8 value; + u8 i2c_init[9] = + {0x80, sd->i2c_addr, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x03}; + + for (i = 0; i < ARRAY_SIZE(bridge_init); i++) { + value = bridge_init[i][1]; + if (reg_w(gspca_dev, bridge_init[i][0], &value, 1) < 0) { + err("Device initialization failed"); + return -ENODEV; + } + } + + if (reg_w(gspca_dev, 0x10c0, i2c_init, 9) < 0) { + err("Device initialization failed"); + return -ENODEV; + } + + switch (sd->sensor) { + case SENSOR_OV9650: + if (ov9650_init_sensor(gspca_dev) < 0) + return -ENODEV; + info("OV9650 sensor detected"); + break; + case SENSOR_OV9655: + if (ov9655_init_sensor(gspca_dev) < 0) + return -ENODEV; + info("OV9655 sensor detected"); + break; + case SENSOR_SOI968: + if (soi968_init_sensor(gspca_dev) < 0) + return -ENODEV; + info("SOI968 sensor detected"); + break; + case SENSOR_OV7660: + if (ov7660_init_sensor(gspca_dev) < 0) + return -ENODEV; + info("OV7660 sensor detected"); + break; + case SENSOR_OV7670: + if (ov7670_init_sensor(gspca_dev) < 0) + return -ENODEV; + info("OV7670 sensor detected"); + break; + case SENSOR_MT9VPRB: + if (mt9v_init_sensor(gspca_dev) < 0) + return -ENODEV; + break; + case SENSOR_MT9M111: + if (mt9m111_init_sensor(gspca_dev) < 0) + return -ENODEV; + info("MT9M111 sensor detected"); + break; + case SENSOR_MT9M001: + if (mt9m001_init_sensor(gspca_dev) < 0) + return -ENODEV; + info("MT9M001 sensor detected"); + break; + case SENSOR_HV7131R: + if (hv7131r_init_sensor(gspca_dev) < 0) + return -ENODEV; + info("HV7131R sensor detected"); + break; + default: + info("Unsupported Sensor"); + return -ENODEV; + } + + return 0; +} + +static void configure_sensor_output(struct gspca_dev *gspca_dev, int mode) +{ + struct sd *sd = (struct sd *) gspca_dev; + u8 value; + switch (sd->sensor) { + case SENSOR_OV9650: + if (mode & MODE_SXGA) { + i2c_w1(gspca_dev, 0x17, 0x1b); + i2c_w1(gspca_dev, 0x18, 0xbc); + i2c_w1(gspca_dev, 0x19, 0x01); + i2c_w1(gspca_dev, 0x1a, 0x82); + i2c_r1(gspca_dev, 0x12, &value); + i2c_w1(gspca_dev, 0x12, value & 0x07); + } else { + i2c_w1(gspca_dev, 0x17, 0x24); + i2c_w1(gspca_dev, 0x18, 0xc5); + i2c_w1(gspca_dev, 0x19, 0x00); + i2c_w1(gspca_dev, 0x1a, 0x3c); + i2c_r1(gspca_dev, 0x12, &value); + i2c_w1(gspca_dev, 0x12, (value & 0x7) | 0x40); + } + break; + } +} + +#define HW_WIN(mode, hstart, vstart) \ +((const u8 []){hstart & 0xff, hstart >> 8, \ +vstart & 0xff, vstart >> 8, \ +(mode & MODE_SXGA ? 1280 >> 4 : 640 >> 4), \ +(mode & MODE_SXGA ? 1024 >> 3 : 480 >> 3)}) + +#define CLR_WIN(width, height) \ +((const u8 [])\ +{0, width >> 2, 0, height >> 1,\ +((width >> 10) & 0x01) | ((height >> 8) & 0x6)}) + +static int sd_start(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + int mode = gspca_dev->cam.cam_mode[(int) gspca_dev->curr_mode].priv; + int width = gspca_dev->width; + int height = gspca_dev->height; + u8 fmt, scale = 0; + + sd->jpeg_hdr = kmalloc(JPEG_HDR_SZ, GFP_KERNEL); + if (sd->jpeg_hdr == NULL) + return -ENOMEM; + + jpeg_define(sd->jpeg_hdr, height, width, + 0x21); + jpeg_set_qual(sd->jpeg_hdr, sd->quality); + + if (mode & MODE_RAW) + fmt = 0x2d; + else if (mode & MODE_JPEG) + fmt = 0x2c; + else + fmt = 0x2f; + + switch (mode & 0x0f) { + case 3: + scale = 0xc0; + info("Set 1280x1024"); + break; + case 2: + scale = 0x80; + info("Set 640x480"); + break; + case 1: + scale = 0x90; + info("Set 320x240"); + break; + case 0: + scale = 0xa0; + info("Set 160x120"); + break; + } + + configure_sensor_output(gspca_dev, mode); + reg_w(gspca_dev, 0x1100, sd->jpeg_hdr + JPEG_QT0_OFFSET, 64); + reg_w(gspca_dev, 0x1140, sd->jpeg_hdr + JPEG_QT1_OFFSET, 64); + reg_w(gspca_dev, 0x10fb, CLR_WIN(width, height), 5); + reg_w(gspca_dev, 0x1180, HW_WIN(mode, sd->hstart, sd->vstart), 6); + reg_w1(gspca_dev, 0x1189, scale); + reg_w1(gspca_dev, 0x10e0, fmt); + + set_cmatrix(gspca_dev); + set_gamma(gspca_dev); + set_redblue(gspca_dev); + set_gain(gspca_dev); + set_exposure(gspca_dev); + set_hvflip(gspca_dev); + + reg_r(gspca_dev, 0x1061, 1); + reg_w1(gspca_dev, 0x1061, gspca_dev->usb_buf[0] | 0x02); + return 0; +} + +static void sd_stopN(struct gspca_dev *gspca_dev) +{ + reg_r(gspca_dev, 0x1061, 1); + reg_w1(gspca_dev, 0x1061, gspca_dev->usb_buf[0] & ~0x02); +} + +static void sd_stop0(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + kfree(sd->jpeg_hdr); +} + +static void do_autoexposure(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + int avg_lum, new_exp; + + if (!sd->auto_exposure) + return; + + avg_lum = atomic_read(&sd->avg_lum); + + /* + * some hardcoded values are present + * like those for maximal/minimal exposure + * and exposure steps + */ + if (avg_lum < MIN_AVG_LUM) { + if (sd->exposure > 0x1770) + return; + + new_exp = sd->exposure + sd->exposure_step; + if (new_exp > 0x1770) + new_exp = 0x1770; + if (new_exp < 0x10) + new_exp = 0x10; + sd->exposure = new_exp; + set_exposure(gspca_dev); + + sd->older_step = sd->old_step; + sd->old_step = 1; + + if (sd->old_step ^ sd->older_step) + sd->exposure_step /= 2; + else + sd->exposure_step += 2; + } + if (avg_lum > MAX_AVG_LUM) { + if (sd->exposure < 0x10) + return; + new_exp = sd->exposure - sd->exposure_step; + if (new_exp > 0x1700) + new_exp = 0x1770; + if (new_exp < 0x10) + new_exp = 0x10; + sd->exposure = new_exp; + set_exposure(gspca_dev); + sd->older_step = sd->old_step; + sd->old_step = 0; + + if (sd->old_step ^ sd->older_step) + sd->exposure_step /= 2; + else + sd->exposure_step += 2; + } +} + +static void sd_pkt_scan(struct gspca_dev *gspca_dev, + struct gspca_frame *frame, /* target */ + u8 *data, /* isoc packet */ + int len) /* iso packet length */ +{ + struct sd *sd = (struct sd *) gspca_dev; + int avg_lum; + static unsigned char frame_header[] = + {0xff, 0xff, 0x00, 0xc4, 0xc4, 0x96}; + if (len == 64 && memcmp(data, frame_header, 6) == 0) { + avg_lum = ((data[35] >> 2) & 3) | + (data[20] << 2) | + (data[19] << 10); + avg_lum += ((data[35] >> 4) & 3) | + (data[22] << 2) | + (data[21] << 10); + avg_lum += ((data[35] >> 6) & 3) | + (data[24] << 2) | + (data[23] << 10); + avg_lum += (data[36] & 3) | + (data[26] << 2) | + (data[25] << 10); + avg_lum += ((data[36] >> 2) & 3) | + (data[28] << 2) | + (data[27] << 10); + avg_lum += ((data[36] >> 4) & 3) | + (data[30] << 2) | + (data[29] << 10); + avg_lum += ((data[36] >> 6) & 3) | + (data[32] << 2) | + (data[31] << 10); + avg_lum += ((data[44] >> 4) & 3) | + (data[34] << 2) | + (data[33] << 10); + avg_lum >>= 9; + atomic_set(&sd->avg_lum, avg_lum); + gspca_frame_add(gspca_dev, LAST_PACKET, + frame, data, len); + return; + } + if (gspca_dev->last_packet_type == LAST_PACKET) { + if (gspca_dev->cam.cam_mode[(int) gspca_dev->curr_mode].priv + & MODE_JPEG) { + gspca_frame_add(gspca_dev, FIRST_PACKET, frame, + sd->jpeg_hdr, JPEG_HDR_SZ); + gspca_frame_add(gspca_dev, INTER_PACKET, frame, + data, len); + } else { + gspca_frame_add(gspca_dev, FIRST_PACKET, frame, + data, len); + } + } else { + gspca_frame_add(gspca_dev, INTER_PACKET, frame, data, len); + } +} + +/* sub-driver description */ +static const struct sd_desc sd_desc = { + .name = MODULE_NAME, + .ctrls = sd_ctrls, + .nctrls = ARRAY_SIZE(sd_ctrls), + .config = sd_config, + .init = sd_init, + .start = sd_start, + .stopN = sd_stopN, + .stop0 = sd_stop0, + .pkt_scan = sd_pkt_scan, + .dq_callback = do_autoexposure, +#ifdef CONFIG_VIDEO_ADV_DEBUG + .set_register = sd_dbg_s_register, + .get_register = sd_dbg_g_register, +#endif + .get_chip_ident = sd_chip_ident, +}; + +#define SN9C20X(sensor, i2c_addr, button_mask) \ + .driver_info = (button_mask << 16) \ + | (SENSOR_ ## sensor << 8) \ + | (i2c_addr) + +static const __devinitdata struct usb_device_id device_table[] = { + {USB_DEVICE(0x0c45, 0x6240), SN9C20X(MT9M001, 0x5d, 0)}, + {USB_DEVICE(0x0c45, 0x6242), SN9C20X(MT9M111, 0x5d, 0)}, + {USB_DEVICE(0x0c45, 0x6248), SN9C20X(OV9655, 0x30, 0)}, + {USB_DEVICE(0x0c45, 0x624e), SN9C20X(SOI968, 0x30, 0x10)}, + {USB_DEVICE(0x0c45, 0x624f), SN9C20X(OV9650, 0x30, 0)}, + {USB_DEVICE(0x0c45, 0x6251), SN9C20X(OV9650, 0x30, 0)}, + {USB_DEVICE(0x0c45, 0x6253), SN9C20X(OV9650, 0x30, 0)}, + {USB_DEVICE(0x0c45, 0x6260), SN9C20X(OV7670, 0x21, 0)}, + {USB_DEVICE(0x0c45, 0x6270), SN9C20X(MT9VPRB, 0x00, 0)}, + {USB_DEVICE(0x0c45, 0x627b), SN9C20X(OV7660, 0x21, 0)}, + {USB_DEVICE(0x0c45, 0x627c), SN9C20X(HV7131R, 0x11, 0)}, + {USB_DEVICE(0x0c45, 0x627f), SN9C20X(OV9650, 0x30, 0)}, + {USB_DEVICE(0x0c45, 0x6280), SN9C20X(MT9M001, 0x5d, 0)}, + {USB_DEVICE(0x0c45, 0x6282), SN9C20X(MT9M111, 0x5d, 0)}, + {USB_DEVICE(0x0c45, 0x6288), SN9C20X(OV9655, 0x30, 0)}, + {USB_DEVICE(0x0c45, 0x628e), SN9C20X(SOI968, 0x30, 0)}, + {USB_DEVICE(0x0c45, 0x628f), SN9C20X(OV9650, 0x30, 0)}, + {USB_DEVICE(0x0c45, 0x62a0), SN9C20X(OV7670, 0x21, 0)}, + {USB_DEVICE(0x0c45, 0x62b0), SN9C20X(MT9VPRB, 0x00, 0)}, + {USB_DEVICE(0x0c45, 0x62b3), SN9C20X(OV9655, 0x30, 0)}, + {USB_DEVICE(0x0c45, 0x62bb), SN9C20X(OV7660, 0x21, 0)}, + {USB_DEVICE(0x0c45, 0x62bc), SN9C20X(HV7131R, 0x11, 0)}, + {USB_DEVICE(0x045e, 0x00f4), SN9C20X(OV9650, 0x30, 0)}, + {USB_DEVICE(0x145f, 0x013d), SN9C20X(OV7660, 0x21, 0)}, + {USB_DEVICE(0x0458, 0x7029), SN9C20X(HV7131R, 0x11, 0)}, + {USB_DEVICE(0xa168, 0x0610), SN9C20X(HV7131R, 0x11, 0)}, + {USB_DEVICE(0xa168, 0x0611), SN9C20X(HV7131R, 0x11, 0)}, + {USB_DEVICE(0xa168, 0x0613), SN9C20X(HV7131R, 0x11, 0)}, + {USB_DEVICE(0xa168, 0x0618), SN9C20X(HV7131R, 0x11, 0)}, + {USB_DEVICE(0xa168, 0x0614), SN9C20X(MT9M111, 0x5d, 0)}, + {USB_DEVICE(0xa168, 0x0615), SN9C20X(MT9M111, 0x5d, 0)}, + {USB_DEVICE(0xa168, 0x0617), SN9C20X(MT9M111, 0x5d, 0)}, + {} +}; +MODULE_DEVICE_TABLE(usb, device_table); + +/* -- device connect -- */ +static int sd_probe(struct usb_interface *intf, + const struct usb_device_id *id) +{ + return gspca_dev_probe(intf, id, &sd_desc, sizeof(struct sd), + THIS_MODULE); +} + +static void sd_disconnect(struct usb_interface *intf) +{ +#ifdef CONFIG_USB_GSPCA_SN9C20X_EVDEV + struct gspca_dev *gspca_dev = usb_get_intfdata(intf); + + sn9c20x_input_cleanup(gspca_dev); +#endif + + gspca_disconnect(intf); +} + +static struct usb_driver sd_driver = { + .name = MODULE_NAME, + .id_table = device_table, + .probe = sd_probe, + .disconnect = sd_disconnect, +#ifdef CONFIG_PM + .suspend = gspca_suspend, + .resume = gspca_resume, + .reset_resume = gspca_resume, +#endif +}; + +/* -- module insert / remove -- */ +static int __init sd_mod_init(void) +{ + int ret; + ret = usb_register(&sd_driver); + if (ret < 0) + return ret; + info("registered"); + return 0; +} +static void __exit sd_mod_exit(void) +{ + usb_deregister(&sd_driver); + info("deregistered"); +} + +module_init(sd_mod_init); +module_exit(sd_mod_exit); diff --git a/include/linux/videodev2.h b/include/linux/videodev2.h index 95846d98801..74f16876f38 100644 --- a/include/linux/videodev2.h +++ b/include/linux/videodev2.h @@ -338,6 +338,7 @@ struct v4l2_pix_format { /* Vendor-specific formats */ #define V4L2_PIX_FMT_WNVA v4l2_fourcc('W', 'N', 'V', 'A') /* Winnov hw compress */ #define V4L2_PIX_FMT_SN9C10X v4l2_fourcc('S', '9', '1', '0') /* SN9C10x compression */ +#define V4L2_PIX_FMT_SN9C20X_I420 v4l2_fourcc('S', '9', '2', '0') /* SN9C20x YUV 4:2:0 */ #define V4L2_PIX_FMT_PWC1 v4l2_fourcc('P', 'W', 'C', '1') /* pwc older webcam */ #define V4L2_PIX_FMT_PWC2 v4l2_fourcc('P', 'W', 'C', '2') /* pwc newer webcam */ #define V4L2_PIX_FMT_ET61X251 v4l2_fourcc('E', '6', '2', '5') /* ET61X251 compression */ diff --git a/include/media/v4l2-chip-ident.h b/include/media/v4l2-chip-ident.h index 11a4a2d3e36..94e908c0d7a 100644 --- a/include/media/v4l2-chip-ident.h +++ b/include/media/v4l2-chip-ident.h @@ -60,6 +60,10 @@ enum { V4L2_IDENT_OV7670 = 250, V4L2_IDENT_OV7720 = 251, V4L2_IDENT_OV7725 = 252, + V4L2_IDENT_OV7660 = 253, + V4L2_IDENT_OV9650 = 254, + V4L2_IDENT_OV9655 = 255, + V4L2_IDENT_SOI968 = 256, /* module saa7146: reserved range 300-309 */ V4L2_IDENT_SAA7146 = 300, @@ -161,6 +165,9 @@ enum { /* module tw9910: just ident 9910 */ V4L2_IDENT_TW9910 = 9910, + /* module sn9c20x: just ident 10000 */ + V4L2_IDENT_SN9C20X = 10000, + /* module msp3400: reserved range 34000-34999 and 44000-44999 */ V4L2_IDENT_MSPX4XX = 34000, /* generic MSPX4XX identifier, only use internally (tveeprom.c). */ @@ -237,6 +244,11 @@ enum { V4L2_IDENT_MT9V022IX7ATC = 45010, /* No way to detect "normal" I77ATx */ V4L2_IDENT_MT9V022IX7ATM = 45015, /* and "lead free" IA7ATx chips */ V4L2_IDENT_MT9T031 = 45020, + V4L2_IDENT_MT9V111 = 45031, + V4L2_IDENT_MT9V112 = 45032, + + /* HV7131R CMOS sensor: just ident 46000 */ + V4L2_IDENT_HV7131R = 46000, /* module cs53132a: just ident 53132 */ V4L2_IDENT_CS53l32A = 53132, -- GitLab From 3eb0237d445c23e9f46b11a07bce986eca450640 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Sun, 19 Jul 2009 07:09:32 -0300 Subject: [PATCH 0303/1342] V4L/DVB (12284): gspca - jpeg subdrivers: Check the result of kmalloc(jpeg header). Signed-off-by: Julia Lawall Signed-off-by: Jean-Francois Moine Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/gspca/conex.c | 2 ++ drivers/media/video/gspca/mars.c | 2 ++ drivers/media/video/gspca/sonixj.c | 2 ++ drivers/media/video/gspca/spca500.c | 2 ++ drivers/media/video/gspca/stk014.c | 2 ++ drivers/media/video/gspca/sunplus.c | 2 ++ drivers/media/video/gspca/zc3xx.c | 2 ++ 7 files changed, 14 insertions(+) diff --git a/drivers/media/video/gspca/conex.c b/drivers/media/video/gspca/conex.c index 219cfa6fb87..8d48ea1742c 100644 --- a/drivers/media/video/gspca/conex.c +++ b/drivers/media/video/gspca/conex.c @@ -846,6 +846,8 @@ static int sd_start(struct gspca_dev *gspca_dev) /* create the JPEG header */ sd->jpeg_hdr = kmalloc(JPEG_HDR_SZ, GFP_KERNEL); + if (!sd->jpeg_hdr) + return -ENOMEM; jpeg_define(sd->jpeg_hdr, gspca_dev->height, gspca_dev->width, 0x22); /* JPEG 411 */ jpeg_set_qual(sd->jpeg_hdr, sd->quality); diff --git a/drivers/media/video/gspca/mars.c b/drivers/media/video/gspca/mars.c index 75e8d14e4ac..de769caf013 100644 --- a/drivers/media/video/gspca/mars.c +++ b/drivers/media/video/gspca/mars.c @@ -201,6 +201,8 @@ static int sd_start(struct gspca_dev *gspca_dev) /* create the JPEG header */ sd->jpeg_hdr = kmalloc(JPEG_HDR_SZ, GFP_KERNEL); + if (!sd->jpeg_hdr) + return -ENOMEM; jpeg_define(sd->jpeg_hdr, gspca_dev->height, gspca_dev->width, 0x21); /* JPEG 422 */ jpeg_set_qual(sd->jpeg_hdr, sd->quality); diff --git a/drivers/media/video/gspca/sonixj.c b/drivers/media/video/gspca/sonixj.c index bad309b90cc..d6332ab8066 100644 --- a/drivers/media/video/gspca/sonixj.c +++ b/drivers/media/video/gspca/sonixj.c @@ -1737,6 +1737,8 @@ static int sd_start(struct gspca_dev *gspca_dev) /* create the JPEG header */ sd->jpeg_hdr = kmalloc(JPEG_HDR_SZ, GFP_KERNEL); + if (!sd->jpeg_hdr) + return -ENOMEM; jpeg_define(sd->jpeg_hdr, gspca_dev->height, gspca_dev->width, 0x21); /* JPEG 422 */ jpeg_set_qual(sd->jpeg_hdr, sd->quality); diff --git a/drivers/media/video/gspca/spca500.c b/drivers/media/video/gspca/spca500.c index 8806b2ff82b..fab7ef85a6c 100644 --- a/drivers/media/video/gspca/spca500.c +++ b/drivers/media/video/gspca/spca500.c @@ -670,6 +670,8 @@ static int sd_start(struct gspca_dev *gspca_dev) /* create the JPEG header */ sd->jpeg_hdr = kmalloc(JPEG_HDR_SZ, GFP_KERNEL); + if (!sd->jpeg_hdr) + return -ENOMEM; jpeg_define(sd->jpeg_hdr, gspca_dev->height, gspca_dev->width, 0x22); /* JPEG 411 */ jpeg_set_qual(sd->jpeg_hdr, sd->quality); diff --git a/drivers/media/video/gspca/stk014.c b/drivers/media/video/gspca/stk014.c index f25be20cf1a..47628964801 100644 --- a/drivers/media/video/gspca/stk014.c +++ b/drivers/media/video/gspca/stk014.c @@ -333,6 +333,8 @@ static int sd_start(struct gspca_dev *gspca_dev) /* create the JPEG header */ sd->jpeg_hdr = kmalloc(JPEG_HDR_SZ, GFP_KERNEL); + if (!sd->jpeg_hdr) + return -ENOMEM; jpeg_define(sd->jpeg_hdr, gspca_dev->height, gspca_dev->width, 0x22); /* JPEG 411 */ jpeg_set_qual(sd->jpeg_hdr, sd->quality); diff --git a/drivers/media/video/gspca/sunplus.c b/drivers/media/video/gspca/sunplus.c index 9623f294bda..5127bbf9dd2 100644 --- a/drivers/media/video/gspca/sunplus.c +++ b/drivers/media/video/gspca/sunplus.c @@ -973,6 +973,8 @@ static int sd_start(struct gspca_dev *gspca_dev) /* create the JPEG header */ sd->jpeg_hdr = kmalloc(JPEG_HDR_SZ, GFP_KERNEL); + if (!sd->jpeg_hdr) + return -ENOMEM; jpeg_define(sd->jpeg_hdr, gspca_dev->height, gspca_dev->width, 0x22); /* JPEG 411 */ jpeg_set_qual(sd->jpeg_hdr, sd->quality); diff --git a/drivers/media/video/gspca/zc3xx.c b/drivers/media/video/gspca/zc3xx.c index 08422d315e6..3d2756f7874 100644 --- a/drivers/media/video/gspca/zc3xx.c +++ b/drivers/media/video/gspca/zc3xx.c @@ -7243,6 +7243,8 @@ static int sd_start(struct gspca_dev *gspca_dev) /* create the JPEG header */ sd->jpeg_hdr = kmalloc(JPEG_HDR_SZ, GFP_KERNEL); + if (!sd->jpeg_hdr) + return -ENOMEM; jpeg_define(sd->jpeg_hdr, gspca_dev->height, gspca_dev->width, 0x21); /* JPEG 422 */ jpeg_set_qual(sd->jpeg_hdr, sd->quality); -- GitLab From c15b95edb98f184e73f756511a60a7994cd9d840 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Sun, 19 Jul 2009 18:03:23 -0300 Subject: [PATCH 0304/1342] V4L/DVB (12286): sn9c20x: reorder includes to be like other drivers This is not just pure cosmetic, since the order affects the out-of-tree module build at the -hg development tree. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/gspca/sn9c20x.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) diff --git a/drivers/media/video/gspca/sn9c20x.c b/drivers/media/video/gspca/sn9c20x.c index 78ab26ceb90..fcfbbd329b4 100644 --- a/drivers/media/video/gspca/sn9c20x.c +++ b/drivers/media/video/gspca/sn9c20x.c @@ -18,10 +18,6 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ -#include "gspca.h" -#include "jpeg.h" - -#include #ifdef CONFIG_USB_GSPCA_SN9C20X_EVDEV #include #include @@ -29,6 +25,11 @@ #include #endif +#include "gspca.h" +#include "jpeg.h" + +#include + MODULE_AUTHOR("Brian Johnson , " "microdia project "); MODULE_DESCRIPTION("GSPCA/SN9C20X USB Camera Driver"); -- GitLab From 68b7f7616add4b1de0fe75015ba3884d2d9ff796 Mon Sep 17 00:00:00 2001 From: Trent Piepho Date: Thu, 11 Jun 2009 19:31:22 -0300 Subject: [PATCH 0305/1342] V4L/DVB (12291): b2c2: fix frontends compiled into kernel A recent patch didn't take into account that frontends can be compiled into the kernel. Or that frontends compiled as modules can't be used by the b2c2 driver if it is not a module itself. Some frontends require multiple drivers, e.g. a demod driver and a tuner driver. The code for the frontend support was getting added if the demod driver was available. Change this to also require any needed tuner or SEC drivers as well. Signed-off-by: Trent Piepho Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb/b2c2/flexcop-fe-tuner.c | 67 +++++++++++++---------- 1 file changed, 37 insertions(+), 30 deletions(-) diff --git a/drivers/media/dvb/b2c2/flexcop-fe-tuner.c b/drivers/media/dvb/b2c2/flexcop-fe-tuner.c index efb4a6c2b57..9a6307a347b 100644 --- a/drivers/media/dvb/b2c2/flexcop-fe-tuner.c +++ b/drivers/media/dvb/b2c2/flexcop-fe-tuner.c @@ -20,8 +20,14 @@ #include "tuner-simple.h" #include "stv0297.h" + +/* Can we use the specified front-end? Remember that if we are compiled + * into the kernel we can't call code that's in modules. */ +#define FE_SUPPORTED(fe) (defined(CONFIG_DVB_##fe) || \ + (defined(CONFIG_DVB_##fe##_MODULE) && defined(MODULE))) + /* lnb control */ -#if defined(CONFIG_DVB_MT312_MODULE) || defined(CONFIG_DVB_STV0299_MODULE) +#if FE_SUPPORTED(MT312) || FE_SUPPORTED(STV0299) static int flexcop_set_voltage(struct dvb_frontend *fe, fe_sec_voltage_t voltage) { struct flexcop_device *fc = fe->dvb->priv; @@ -49,8 +55,7 @@ static int flexcop_set_voltage(struct dvb_frontend *fe, fe_sec_voltage_t voltage } #endif -#if defined(CONFIG_DVB_S5H1420_MODULE) || defined(CONFIG_DVB_STV0299_MODULE) \ - || defined(CONFIG_DVB_MT312_MODULE) +#if FE_SUPPORTED(S5H1420) || FE_SUPPORTED(STV0299) || FE_SUPPORTED(MT312) static int flexcop_sleep(struct dvb_frontend* fe) { struct flexcop_device *fc = fe->dvb->priv; @@ -61,7 +66,7 @@ static int flexcop_sleep(struct dvb_frontend* fe) #endif /* SkyStar2 DVB-S rev 2.3 */ -#if defined(CONFIG_DVB_MT312_MODULE) +#if FE_SUPPORTED(MT312) static int flexcop_set_tone(struct dvb_frontend *fe, fe_sec_tone_mode_t tone) { /* u16 wz_half_period_for_45_mhz[] = { 0x01ff, 0x0154, 0x00ff, 0x00cc }; */ @@ -193,10 +198,12 @@ static int skystar2_rev23_attach(struct flexcop_device *fc, } return 0; } +#else +#define skystar2_rev23_attach NULL #endif /* SkyStar2 DVB-S rev 2.6 */ -#if defined(CONFIG_DVB_STV0299_MODULE) +#if FE_SUPPORTED(STV0299) static int samsung_tbmu24112_set_symbol_rate(struct dvb_frontend *fe, u32 srate, u32 ratio) { @@ -321,10 +328,12 @@ static int skystar2_rev26_attach(struct flexcop_device *fc, } return 0; } +#else +#define skystar2_rev26_attach NULL #endif /* SkyStar2 DVB-S rev 2.7 */ -#if defined(CONFIG_DVB_S5H1420_MODULE) +#if FE_SUPPORTED(S5H1420) && FE_SUPPORTED(ISL6421) && FE_SUPPORTED(TUNER_ITD1000) static struct s5h1420_config skystar2_rev2_7_s5h1420_config = { .demod_address = 0x53, .invert = 1, @@ -385,10 +394,12 @@ fail: fc->fc_i2c_adap[0].no_base_addr = 0; return 0; } +#else +#define skystar2_rev27_attach NULL #endif /* SkyStar2 rev 2.8 */ -#if defined(CONFIG_DVB_CX24123_MODULE) +#if FE_SUPPORTED(CX24123) && FE_SUPPORTED(ISL6421) && FE_SUPPORTED(TUNER_CX24113) static struct cx24123_config skystar2_rev2_8_cx24123_config = { .demod_address = 0x55, .dont_use_pll = 1, @@ -433,10 +444,12 @@ static int skystar2_rev28_attach(struct flexcop_device *fc, * IR-receiver (PIC16F818) - but the card has no input for that ??? */ return 1; } +#else +#define skystar2_rev28_attach NULL #endif /* AirStar DVB-T */ -#if defined(CONFIG_DVB_MT352_MODULE) +#if FE_SUPPORTED(MT352) static int samsung_tdtc9251dh0_demod_init(struct dvb_frontend *fe) { static u8 mt352_clock_config[] = { 0x89, 0x18, 0x2d }; @@ -495,10 +508,12 @@ static int airstar_dvbt_attach(struct flexcop_device *fc, } return 0; } +#else +#define airstar_dvbt_attach NULL #endif /* AirStar ATSC 1st generation */ -#if defined(CONFIG_DVB_BCM3510_MODULE) +#if FE_SUPPORTED(BCM3510) static int flexcop_fe_request_firmware(struct dvb_frontend *fe, const struct firmware **fw, char* name) { @@ -517,10 +532,12 @@ static int airstar_atsc1_attach(struct flexcop_device *fc, fc->fe = dvb_attach(bcm3510_attach, &air2pc_atsc_first_gen_config, i2c); return fc->fe != NULL; } +#else +#define airstar_atsc1_attach NULL #endif /* AirStar ATSC 2nd generation */ -#if defined(CONFIG_DVB_NXT200X_MODULE) +#if FE_SUPPORTED(NXT200X) && FE_SUPPORTED(PLL) static struct nxt200x_config samsung_tbmv_config = { .demod_address = 0x0a, }; @@ -535,10 +552,12 @@ static int airstar_atsc2_attach(struct flexcop_device *fc, return !!dvb_attach(dvb_pll_attach, fc->fe, 0x61, NULL, DVB_PLL_SAMSUNG_TBMV); } +#else +#define airstar_atsc2_attach NULL #endif /* AirStar ATSC 3rd generation */ -#if defined(CONFIG_DVB_LGDT330X_MODULE) +#if FE_SUPPORTED(LGDT330X) static struct lgdt330x_config air2pc_atsc_hd5000_config = { .demod_address = 0x59, .demod_chip = LGDT3303, @@ -556,10 +575,12 @@ static int airstar_atsc3_attach(struct flexcop_device *fc, return !!dvb_attach(simple_tuner_attach, fc->fe, i2c, 0x61, TUNER_LG_TDVS_H06XF); } +#else +#define airstar_atsc3_attach NULL #endif /* CableStar2 DVB-C */ -#if defined(CONFIG_DVB_STV0297_MODULE) +#if FE_SUPPORTED(STV0297) static int alps_tdee4_stv0297_tuner_set_params(struct dvb_frontend* fe, struct dvb_frontend_parameters *fep) { @@ -698,39 +719,23 @@ static int cablestar2_attach(struct flexcop_device *fc, fc->fe->ops.tuner_ops.set_params = alps_tdee4_stv0297_tuner_set_params; return 1; } +#else +#define cablestar2_attach NULL #endif static struct { flexcop_device_type_t type; int (*attach)(struct flexcop_device *, struct i2c_adapter *); } flexcop_frontends[] = { -#if defined(CONFIG_DVB_S5H1420_MODULE) { FC_SKY_REV27, skystar2_rev27_attach }, -#endif -#if defined(CONFIG_DVB_CX24123_MODULE) { FC_SKY_REV28, skystar2_rev28_attach }, -#endif -#if defined(CONFIG_DVB_STV0299_MODULE) { FC_SKY_REV26, skystar2_rev26_attach }, -#endif -#if defined(CONFIG_DVB_MT352_MODULE) { FC_AIR_DVBT, airstar_dvbt_attach }, -#endif -#if defined(CONFIG_DVB_NXT200X_MODULE) { FC_AIR_ATSC2, airstar_atsc2_attach }, -#endif -#if defined(CONFIG_DVB_LGDT330X_MODULE) { FC_AIR_ATSC3, airstar_atsc3_attach }, -#endif -#if defined(CONFIG_DVB_BCM3510_MODULE) { FC_AIR_ATSC1, airstar_atsc1_attach }, -#endif -#if defined(CONFIG_DVB_STV0297_MODULE) { FC_CABLE, cablestar2_attach }, -#endif -#if defined(CONFIG_DVB_MT312_MODULE) { FC_SKY_REV23, skystar2_rev23_attach }, -#endif }; /* try to figure out the frontend */ @@ -738,6 +743,8 @@ int flexcop_frontend_init(struct flexcop_device *fc) { int i; for (i = 0; i < ARRAY_SIZE(flexcop_frontends); i++) { + if (!flexcop_frontends[i].attach) + continue; /* type needs to be set before, because of some workarounds * done based on the probed card type */ fc->dev_type = flexcop_frontends[i].type; -- GitLab From 2c90577841a76f1935ff3437ffb552b41f5c28fa Mon Sep 17 00:00:00 2001 From: Hans Verkuil Date: Mon, 20 Jul 2009 08:14:17 -0300 Subject: [PATCH 0306/1342] V4L/DVB (12300): bttv: fix regression: tvaudio must be loaded before tuner Both tvaudio and the tuner share i2c address 0x42. The tvaudio module can check whether it really is a tda9840, but the tuner can't. So the tvaudio module must be loaded before the tuner module. This was also the case for 2.6.29, but the order was swapped in 2.6.30. Thanks to Krzysztof Grygiencz for reporting and testing this. Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/bt8xx/bttv-cards.c | 92 +++++++++++++------------ drivers/media/video/bt8xx/bttv-driver.c | 1 + drivers/media/video/bt8xx/bttv.h | 1 + 3 files changed, 50 insertions(+), 44 deletions(-) diff --git a/drivers/media/video/bt8xx/bttv-cards.c b/drivers/media/video/bt8xx/bttv-cards.c index fdb4adff3d2..ca6558c394b 100644 --- a/drivers/media/video/bt8xx/bttv-cards.c +++ b/drivers/media/video/bt8xx/bttv-cards.c @@ -3324,8 +3324,6 @@ void __devinit bttv_init_card1(struct bttv *btv) /* initialization part two -- after registering i2c bus */ void __devinit bttv_init_card2(struct bttv *btv) { - int addr=ADDR_UNSET; - btv->tuner_type = UNSET; if (BTTV_BOARD_UNKNOWN == btv->c.type) { @@ -3470,9 +3468,6 @@ void __devinit bttv_init_card2(struct bttv *btv) btv->pll.pll_current = -1; /* tuner configuration (from card list / autodetect / insmod option) */ - if (ADDR_UNSET != bttv_tvcards[btv->c.type].tuner_addr) - addr = bttv_tvcards[btv->c.type].tuner_addr; - if (UNSET != bttv_tvcards[btv->c.type].tuner_type) if (UNSET == btv->tuner_type) btv->tuner_type = bttv_tvcards[btv->c.type].tuner_type; @@ -3496,40 +3491,6 @@ void __devinit bttv_init_card2(struct bttv *btv) if (UNSET == btv->tuner_type) btv->tuner_type = TUNER_ABSENT; - if (btv->tuner_type != TUNER_ABSENT) { - struct tuner_setup tun_setup; - - /* Load tuner module before issuing tuner config call! */ - if (bttv_tvcards[btv->c.type].has_radio) - v4l2_i2c_new_probed_subdev(&btv->c.v4l2_dev, - &btv->c.i2c_adap, "tuner", "tuner", - v4l2_i2c_tuner_addrs(ADDRS_RADIO)); - v4l2_i2c_new_probed_subdev(&btv->c.v4l2_dev, - &btv->c.i2c_adap, "tuner", "tuner", - v4l2_i2c_tuner_addrs(ADDRS_DEMOD)); - v4l2_i2c_new_probed_subdev(&btv->c.v4l2_dev, - &btv->c.i2c_adap, "tuner", "tuner", - v4l2_i2c_tuner_addrs(ADDRS_TV_WITH_DEMOD)); - - tun_setup.mode_mask = T_ANALOG_TV | T_DIGITAL_TV; - tun_setup.type = btv->tuner_type; - tun_setup.addr = addr; - - if (bttv_tvcards[btv->c.type].has_radio) - tun_setup.mode_mask |= T_RADIO; - - bttv_call_all(btv, tuner, s_type_addr, &tun_setup); - } - - if (btv->tda9887_conf) { - struct v4l2_priv_tun_config tda9887_cfg; - - tda9887_cfg.tuner = TUNER_TDA9887; - tda9887_cfg.priv = &btv->tda9887_conf; - - bttv_call_all(btv, tuner, s_config, &tda9887_cfg); - } - btv->dig = bttv_tvcards[btv->c.type].has_dig_in ? bttv_tvcards[btv->c.type].video_inputs - 1 : UNSET; btv->svhs = bttv_tvcards[btv->c.type].svhs == NO_SVHS ? @@ -3540,15 +3501,15 @@ void __devinit bttv_init_card2(struct bttv *btv) btv->has_remote = remote[btv->c.nr]; if (bttv_tvcards[btv->c.type].has_radio) - btv->has_radio=1; + btv->has_radio = 1; if (bttv_tvcards[btv->c.type].has_remote) - btv->has_remote=1; + btv->has_remote = 1; if (!bttv_tvcards[btv->c.type].no_gpioirq) - btv->gpioirq=1; + btv->gpioirq = 1; if (bttv_tvcards[btv->c.type].volume_gpio) - btv->volume_gpio=bttv_tvcards[btv->c.type].volume_gpio; + btv->volume_gpio = bttv_tvcards[btv->c.type].volume_gpio; if (bttv_tvcards[btv->c.type].audio_mode_gpio) - btv->audio_mode_gpio=bttv_tvcards[btv->c.type].audio_mode_gpio; + btv->audio_mode_gpio = bttv_tvcards[btv->c.type].audio_mode_gpio; if (btv->tuner_type == TUNER_ABSENT) return; /* no tuner or related drivers to load */ @@ -3666,6 +3627,49 @@ no_audio: } +/* initialize the tuner */ +void __devinit bttv_init_tuner(struct bttv *btv) +{ + int addr = ADDR_UNSET; + + if (ADDR_UNSET != bttv_tvcards[btv->c.type].tuner_addr) + addr = bttv_tvcards[btv->c.type].tuner_addr; + + if (btv->tuner_type != TUNER_ABSENT) { + struct tuner_setup tun_setup; + + /* Load tuner module before issuing tuner config call! */ + if (bttv_tvcards[btv->c.type].has_radio) + v4l2_i2c_new_probed_subdev(&btv->c.v4l2_dev, + &btv->c.i2c_adap, "tuner", "tuner", + v4l2_i2c_tuner_addrs(ADDRS_RADIO)); + v4l2_i2c_new_probed_subdev(&btv->c.v4l2_dev, + &btv->c.i2c_adap, "tuner", "tuner", + v4l2_i2c_tuner_addrs(ADDRS_DEMOD)); + v4l2_i2c_new_probed_subdev(&btv->c.v4l2_dev, + &btv->c.i2c_adap, "tuner", "tuner", + v4l2_i2c_tuner_addrs(ADDRS_TV_WITH_DEMOD)); + + tun_setup.mode_mask = T_ANALOG_TV | T_DIGITAL_TV; + tun_setup.type = btv->tuner_type; + tun_setup.addr = addr; + + if (bttv_tvcards[btv->c.type].has_radio) + tun_setup.mode_mask |= T_RADIO; + + bttv_call_all(btv, tuner, s_type_addr, &tun_setup); + } + + if (btv->tda9887_conf) { + struct v4l2_priv_tun_config tda9887_cfg; + + tda9887_cfg.tuner = TUNER_TDA9887; + tda9887_cfg.priv = &btv->tda9887_conf; + + bttv_call_all(btv, tuner, s_config, &tda9887_cfg); + } +} + /* ----------------------------------------------------------------------- */ static void modtec_eeprom(struct bttv *btv) diff --git a/drivers/media/video/bt8xx/bttv-driver.c b/drivers/media/video/bt8xx/bttv-driver.c index d147d29bb0d..8cc6dd28d6a 100644 --- a/drivers/media/video/bt8xx/bttv-driver.c +++ b/drivers/media/video/bt8xx/bttv-driver.c @@ -4419,6 +4419,7 @@ static int __devinit bttv_probe(struct pci_dev *dev, /* some card-specific stuff (needs working i2c) */ bttv_init_card2(btv); + bttv_init_tuner(btv); init_irqreg(btv); /* register video4linux + input */ diff --git a/drivers/media/video/bt8xx/bttv.h b/drivers/media/video/bt8xx/bttv.h index 3d36daf206f..3ec2402c6b4 100644 --- a/drivers/media/video/bt8xx/bttv.h +++ b/drivers/media/video/bt8xx/bttv.h @@ -283,6 +283,7 @@ extern struct tvcard bttv_tvcards[]; extern void bttv_idcard(struct bttv *btv); extern void bttv_init_card1(struct bttv *btv); extern void bttv_init_card2(struct bttv *btv); +extern void bttv_init_tuner(struct bttv *btv); /* card-specific funtions */ extern void tea5757_set_freq(struct bttv *btv, unsigned short freq); -- GitLab From 12a34cc8a9a49219ab643c8ec329078eec272b47 Mon Sep 17 00:00:00 2001 From: Michael Krufky Date: Sun, 19 Jul 2009 18:19:18 -0300 Subject: [PATCH 0307/1342] V4L/DVB (12302): cx23885-417: fix broken IOCTL handling IOCTLS will never get handled if we dont connect video_ioctl2 to mpeg_fops.ioctl Signed-off-by: Michael Krufky Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/cx23885/cx23885-417.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/media/video/cx23885/cx23885-417.c b/drivers/media/video/cx23885/cx23885-417.c index 428f0c45e6b..2ea7181ae8f 100644 --- a/drivers/media/video/cx23885/cx23885-417.c +++ b/drivers/media/video/cx23885/cx23885-417.c @@ -1677,6 +1677,7 @@ static struct v4l2_file_operations mpeg_fops = { .read = mpeg_read, .poll = mpeg_poll, .mmap = mpeg_mmap, + .ioctl = video_ioctl2, }; static const struct v4l2_ioctl_ops mpeg_ioctl_ops = { -- GitLab From ca4e771f7b878b7bab02dedb539f7742f9b4f50e Mon Sep 17 00:00:00 2001 From: Michael Krufky Date: Sun, 19 Jul 2009 17:55:35 -0300 Subject: [PATCH 0308/1342] V4L/DVB (12303): cx23885: check pointers before dereferencing in dprintk macro When enabling debug with v4l_debug set to 2 or greater, the driver OOPS's on startup. Checks dev pointer before dereferencing, in order to prevent this OOPS. Signed-off-by: Michael Krufky Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/cx23885/cx23885-417.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/media/video/cx23885/cx23885-417.c b/drivers/media/video/cx23885/cx23885-417.c index 2ea7181ae8f..e0cf21e0b1b 100644 --- a/drivers/media/video/cx23885/cx23885-417.c +++ b/drivers/media/video/cx23885/cx23885-417.c @@ -58,7 +58,8 @@ MODULE_PARM_DESC(v4l_debug, "enable V4L debug messages"); #define dprintk(level, fmt, arg...)\ do { if (v4l_debug >= level) \ - printk(KERN_DEBUG "%s: " fmt, dev->name , ## arg);\ + printk(KERN_DEBUG "%s: " fmt, \ + (dev) ? dev->name : "cx23885[?]", ## arg); \ } while (0) static struct cx23885_tvnorm cx23885_tvnorms[] = { -- GitLab From 7194e6f9c083e87171ddfc8b746f05e007f58132 Mon Sep 17 00:00:00 2001 From: Adrian Hunter Date: Fri, 24 Jul 2009 17:05:00 +0300 Subject: [PATCH 0309/1342] UBI: fix double free on error path If we fail in 'ubi_eba_init_scan()', we free 'ubi->volumes[i]->eba_tbl' in there, but also later free it in 'free_internal_volumes()'. Fix this by assigning NULL to 'ubi->volumes[i]->eba_tbl' after it is freed. Signed-off-by: Adrian Hunter Signed-off-by: Artem Bityutskiy --- drivers/mtd/ubi/eba.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/mtd/ubi/eba.c b/drivers/mtd/ubi/eba.c index 0f2034c3ed2..e4d9ef0c965 100644 --- a/drivers/mtd/ubi/eba.c +++ b/drivers/mtd/ubi/eba.c @@ -1254,6 +1254,7 @@ out_free: if (!ubi->volumes[i]) continue; kfree(ubi->volumes[i]->eba_tbl); + ubi->volumes[i]->eba_tbl = NULL; } return err; } -- GitLab From 32bc4820287a1a03982979515949e8ea56eac641 Mon Sep 17 00:00:00 2001 From: Adrian Hunter Date: Fri, 24 Jul 2009 19:16:04 +0300 Subject: [PATCH 0310/1342] UBI: compatible fallback in absense of sequence numbers Fall back onto thinking everything's OK if either of the sequence numbers we are asked to compare is zero, which is what was used before sequence numbers were introduced. [ Artem: modified the patch to be applicable to upstream UBI, added big comment ] Signed-off-by: Adrian Hunter Signed-off-by: Phil Carmody Signed-off-by: Artem Bityutskiy --- drivers/mtd/ubi/scan.c | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-) diff --git a/drivers/mtd/ubi/scan.c b/drivers/mtd/ubi/scan.c index a423131b617..b847745394b 100644 --- a/drivers/mtd/ubi/scan.c +++ b/drivers/mtd/ubi/scan.c @@ -781,11 +781,22 @@ static int process_eb(struct ubi_device *ubi, struct ubi_scan_info *si, return -EINVAL; } + /* + * Make sure that all PEBs have the same image sequence number. + * This allows us to detect situations when users flash UBI + * images incorrectly, so that the flash has the new UBI image + * and leftovers from the old one. This feature was added + * relatively recently, and the sequence number was always + * zero, because old UBI implementations always set it to zero. + * For this reasons, we do not panic if some PEBs have zero + * sequence number, while other PEBs have non-zero sequence + * number. + */ image_seq = be32_to_cpu(ech->image_seq); if (!si->image_seq_set) { ubi->image_seq = image_seq; si->image_seq_set = 1; - } else if (ubi->image_seq != image_seq) { + } else if (ubi->image_seq && ubi->image_seq != image_seq) { ubi_err("bad image sequence number %d in PEB %d, " "expected %d", image_seq, pnum, ubi->image_seq); ubi_dbg_dump_ec_hdr(ech); -- GitLab From ebecd3d9d2adba144c15f1d35c78e0c26ead1bfd Mon Sep 17 00:00:00 2001 From: Sage Weil Date: Fri, 24 Jul 2009 13:17:44 -0400 Subject: [PATCH 0311/1342] Btrfs: make flushoncommit mount option correctly wait on ordered_extents The commit_transaction call to wait_ordered_extents when snap_pending passes nocow_only=1 to process only NOCOW or PREALLOC extents. This isn't correct for the 'flushoncommit' mode, as it skips extents we just started IO on in start_delalloc_inodes. So, in the flushoncommit case, wait on all ordered extents. Otherwise, only pass the nocow_only flag to wait_ordered_extents if snap_pending. Signed-off-by: Sage Weil Signed-off-by: Chris Mason --- fs/btrfs/transaction.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) diff --git a/fs/btrfs/transaction.c b/fs/btrfs/transaction.c index 32454d1c566..e51d2bc532f 100644 --- a/fs/btrfs/transaction.c +++ b/fs/btrfs/transaction.c @@ -942,9 +942,11 @@ int btrfs_commit_transaction(struct btrfs_trans_handle *trans, mutex_unlock(&root->fs_info->trans_mutex); - if (flush_on_commit || snap_pending) { - if (flush_on_commit) - btrfs_start_delalloc_inodes(root); + if (flush_on_commit) { + btrfs_start_delalloc_inodes(root); + ret = btrfs_wait_ordered_extents(root, 0); + BUG_ON(ret); + } else if (snap_pending) { ret = btrfs_wait_ordered_extents(root, 1); BUG_ON(ret); } -- GitLab From bdff78707f3ce47e891f3201c9666122a70556ce Mon Sep 17 00:00:00 2001 From: Thomas Gleixner Date: Fri, 24 Jul 2009 15:30:45 -0400 Subject: [PATCH 0312/1342] trace: stop tracer in oops_enter() If trace_printk_on_oops is set we lose interesting trace information when the tracer is enabled across oops handling and printing. We want the trace which might give us information _WHY_ we oopsed. Signed-off-by: Thomas Gleixner Signed-off-by: Steven Rostedt --- kernel/panic.c | 1 + 1 file changed, 1 insertion(+) diff --git a/kernel/panic.c b/kernel/panic.c index 984b3ecbd72..512ab73b0ca 100644 --- a/kernel/panic.c +++ b/kernel/panic.c @@ -301,6 +301,7 @@ int oops_may_print(void) */ void oops_enter(void) { + tracing_off(); /* can't trust the integrity of the kernel anymore: */ debug_locks_off(); do_oops_enter_exit(); -- GitLab From 283bb1979fa8580c4037d8df251449368c292a3b Mon Sep 17 00:00:00 2001 From: Chris Mason Date: Fri, 24 Jul 2009 16:30:55 -0400 Subject: [PATCH 0313/1342] Btrfs: clear all space_info->full after removing a block group Btrfs allocates individual extents from block groups, and each block group has a specific type. It may hold metadata, data mirrored or striped etc. When we balance space (btrfs-vol -b) or remove a drive (btrfs-vol -r) we free block groups. Once a block group is freed, the space it was using on the device may be available for use by new block groups. btrfs_remove_block_group was clearing the flag that said 'our devices are full, don't even try to allocate new block groups', but it was only clearing that flag for a specific type of block group. This commit clears the full flag for all of the types of block groups, making it much more likely that we'll be able to balance space when the drive is close to full. Signed-off-by: Chris Mason --- fs/btrfs/extent-tree.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c index 9a489cc89fd..508df5f7d2e 100644 --- a/fs/btrfs/extent-tree.c +++ b/fs/btrfs/extent-tree.c @@ -7486,7 +7486,8 @@ int btrfs_remove_block_group(struct btrfs_trans_handle *trans, block_group->space_info->total_bytes -= block_group->key.offset; block_group->space_info->bytes_readonly -= block_group->key.offset; spin_unlock(&block_group->space_info->lock); - block_group->space_info->full = 0; + + btrfs_clear_space_info_full(root->fs_info); btrfs_put_block_group(block_group); btrfs_put_block_group(block_group); -- GitLab From 9779b72f0584fd53e0de53f62f205bf0dc0db553 Mon Sep 17 00:00:00 2001 From: Chris Mason Date: Fri, 24 Jul 2009 16:41:41 -0400 Subject: [PATCH 0314/1342] Btrfs: find smallest available device extent during chunk allocation Allocating new block group is easy when the disk has plenty of space. But things get difficult as the disk fills up, especially if the FS has been run through btrfs-vol -b. The balance operation is likely to make the total bytes available on the device greater than the largest extent we'll actually be able to allocate. But the device extent allocation code incorrectly assumes that a device with 5G free will be able to allocate a 5G extent. It isn't normally a problem because device extents don't get freed unless btrfs-vol -b is run. This fixes the device extent allocator to remember the largest free extent it can find, and then uses that value as a fallback. Signed-off-by: Chris Mason --- fs/btrfs/volumes.c | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-) diff --git a/fs/btrfs/volumes.c b/fs/btrfs/volumes.c index 074c1c56d8c..5dbefd11b4a 100644 --- a/fs/btrfs/volumes.c +++ b/fs/btrfs/volumes.c @@ -721,7 +721,8 @@ error: */ static noinline int find_free_dev_extent(struct btrfs_trans_handle *trans, struct btrfs_device *device, - u64 num_bytes, u64 *start) + u64 num_bytes, u64 *start, + u64 *max_avail) { struct btrfs_key key; struct btrfs_root *root = device->dev_root; @@ -807,6 +808,10 @@ no_more_items: if (last_byte < search_start) last_byte = search_start; hole_size = key.offset - last_byte; + + if (hole_size > *max_avail) + *max_avail = hole_size; + if (key.offset > last_byte && hole_size >= num_bytes) { *start = last_byte; @@ -1625,6 +1630,7 @@ static int __btrfs_grow_device(struct btrfs_trans_handle *trans, device->fs_devices->total_rw_bytes += diff; device->total_bytes = new_size; + device->disk_total_bytes = new_size; btrfs_clear_space_info_full(device->dev_root->fs_info); return btrfs_update_device(trans, device); @@ -2175,6 +2181,7 @@ static int __btrfs_alloc_chunk(struct btrfs_trans_handle *trans, max_chunk_size); again: + max_avail = 0; if (!map || map->num_stripes != num_stripes) { kfree(map); map = kmalloc(map_lookup_size(num_stripes), GFP_NOFS); @@ -2223,7 +2230,8 @@ again: if (device->in_fs_metadata && avail >= min_free) { ret = find_free_dev_extent(trans, device, - min_free, &dev_offset); + min_free, &dev_offset, + &max_avail); if (ret == 0) { list_move_tail(&device->dev_alloc_list, &private_devs); -- GitLab From 58cda884ecc87dcce18d463b0c8bd928dae63ad8 Mon Sep 17 00:00:00 2001 From: Jean Pihet Date: Fri, 24 Jul 2009 19:43:25 -0600 Subject: [PATCH 0315/1342] OMAP3 SDRC: add support for 2 SDRAM chip selects Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2 SDRAM parts connected to the SDRC. This patch adds the following: - add a new argument of type omap_sdrc_params struct* to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params - adapted the OMAP boards files to the new prototype of omap2_init_common_hw - add the SDRC 2nd CS registers offsets defines - adapt the sram sleep code to configure the SDRC for the 2nd CS Note: If the 2nd param to omap2_init_common_hw is NULL, then the parameters are not programmed into the SDRC CS1 registers Tested on 3430 SDP and Beagleboard rev C2 and B5, with suspend/resume and frequency changes (cpufreq). Signed-off-by: Jean Pihet Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/board-2430sdp.c | 2 +- arch/arm/mach-omap2/board-3430sdp.c | 2 +- arch/arm/mach-omap2/board-4430sdp.c | 2 +- arch/arm/mach-omap2/board-apollon.c | 2 +- arch/arm/mach-omap2/board-generic.c | 2 +- arch/arm/mach-omap2/board-h4.c | 2 +- arch/arm/mach-omap2/board-ldp.c | 2 +- arch/arm/mach-omap2/board-omap3beagle.c | 3 +- arch/arm/mach-omap2/board-omap3evm.c | 2 +- arch/arm/mach-omap2/board-omap3pandora.c | 3 +- arch/arm/mach-omap2/board-overo.c | 3 +- arch/arm/mach-omap2/board-rx51.c | 2 +- arch/arm/mach-omap2/board-zoom2.c | 2 +- arch/arm/mach-omap2/clock34xx.c | 37 ++++-- arch/arm/mach-omap2/io.c | 5 +- arch/arm/mach-omap2/sdrc.c | 63 +++++++---- arch/arm/mach-omap2/sram34xx.S | 137 ++++++++++++++++++----- arch/arm/plat-omap/include/mach/io.h | 3 +- arch/arm/plat-omap/include/mach/sdrc.h | 11 +- arch/arm/plat-omap/include/mach/sram.h | 23 ++-- arch/arm/plat-omap/sram.c | 30 +++-- 21 files changed, 236 insertions(+), 102 deletions(-) diff --git a/arch/arm/mach-omap2/board-2430sdp.c b/arch/arm/mach-omap2/board-2430sdp.c index 9c3fdcdf76c..8ec2a132904 100644 --- a/arch/arm/mach-omap2/board-2430sdp.c +++ b/arch/arm/mach-omap2/board-2430sdp.c @@ -141,7 +141,7 @@ static inline void board_smc91x_init(void) static void __init omap_2430sdp_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c index 496a90e4ea7..ac262cd7450 100644 --- a/arch/arm/mach-omap2/board-3430sdp.c +++ b/arch/arm/mach-omap2/board-3430sdp.c @@ -169,7 +169,7 @@ static struct platform_device *sdp3430_devices[] __initdata = { static void __init omap_3430sdp_init_irq(void) { - omap2_init_common_hw(hyb18m512160af6_sdrc_params); + omap2_init_common_hw(hyb18m512160af6_sdrc_params, NULL); omap_init_irq(); omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c index 57e477bd89c..b0c7402248f 100644 --- a/arch/arm/mach-omap2/board-4430sdp.c +++ b/arch/arm/mach-omap2/board-4430sdp.c @@ -59,7 +59,7 @@ static void __init gic_init_irq(void) static void __init omap_4430sdp_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); #ifdef CONFIG_OMAP_32K_TIMER omap2_gp_clockevent_set_gptimer(1); #endif diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c index 06dfba888b0..dcfc20d0389 100644 --- a/arch/arm/mach-omap2/board-apollon.c +++ b/arch/arm/mach-omap2/board-apollon.c @@ -250,7 +250,7 @@ out: static void __init omap_apollon_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); omap_gpio_init(); apollon_init_smc91x(); diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c index 3492162a65c..fd00aa03690 100644 --- a/arch/arm/mach-omap2/board-generic.c +++ b/arch/arm/mach-omap2/board-generic.c @@ -33,7 +33,7 @@ static void __init omap_generic_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); } diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c index e7d017cdc43..7b1d61d5bb2 100644 --- a/arch/arm/mach-omap2/board-h4.c +++ b/arch/arm/mach-omap2/board-h4.c @@ -270,7 +270,7 @@ static void __init h4_init_flash(void) static void __init omap_h4_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); omap_gpio_init(); h4_init_flash(); diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c index d8bc0a7dcb8..ea383f88cb1 100644 --- a/arch/arm/mach-omap2/board-ldp.c +++ b/arch/arm/mach-omap2/board-ldp.c @@ -270,7 +270,7 @@ static inline void __init ldp_init_smsc911x(void) static void __init omap_ldp_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); omap_gpio_init(); ldp_init_smsc911x(); diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 991ac9c3803..4abefd9566e 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -282,7 +282,8 @@ static int __init omap3_beagle_i2c_init(void) static void __init omap3_beagle_init_irq(void) { - omap2_init_common_hw(mt46h32m32lf6_sdrc_params); + omap2_init_common_hw(mt46h32m32lf6_sdrc_params, + mt46h32m32lf6_sdrc_params); omap_init_irq(); #ifdef CONFIG_OMAP_32K_TIMER omap2_gp_clockevent_set_gptimer(12); diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index d3cc145814d..217e5a2861d 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -279,7 +279,7 @@ struct spi_board_info omap3evm_spi_board_info[] = { static void __init omap3_evm_init_irq(void) { - omap2_init_common_hw(mt46h32m32lf6_sdrc_params); + omap2_init_common_hw(mt46h32m32lf6_sdrc_params, NULL); omap_init_irq(); omap_gpio_init(); omap3evm_init_smc911x(); diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c index e32aa23ce96..9b991ced382 100644 --- a/arch/arm/mach-omap2/board-omap3pandora.c +++ b/arch/arm/mach-omap2/board-omap3pandora.c @@ -310,7 +310,8 @@ static int __init omap3pandora_i2c_init(void) static void __init omap3pandora_init_irq(void) { - omap2_init_common_hw(mt46h32m32lf6_sdrc_params); + omap2_init_common_hw(mt46h32m32lf6_sdrc_params, + mt46h32m32lf6_sdrc_params); omap_init_irq(); omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index dff5528fbfb..44bc1c54cd0 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -360,7 +360,8 @@ static int __init overo_i2c_init(void) static void __init overo_init_irq(void) { - omap2_init_common_hw(mt46h32m32lf6_sdrc_params); + omap2_init_common_hw(mt46h32m32lf6_sdrc_params, + mt46h32m32lf6_sdrc_params); omap_init_irq(); omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/board-rx51.c b/arch/arm/mach-omap2/board-rx51.c index 374ff63c3eb..591ae8a5805 100644 --- a/arch/arm/mach-omap2/board-rx51.c +++ b/arch/arm/mach-omap2/board-rx51.c @@ -61,7 +61,7 @@ static struct omap_board_config_kernel rx51_config[] = { static void __init rx51_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/board-zoom2.c b/arch/arm/mach-omap2/board-zoom2.c index bcc0f7632de..427b7b8b123 100644 --- a/arch/arm/mach-omap2/board-zoom2.c +++ b/arch/arm/mach-omap2/board-zoom2.c @@ -25,7 +25,7 @@ static void __init omap_zoom2_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c index 045da923e75..1c6480d3ad6 100644 --- a/arch/arm/mach-omap2/clock34xx.c +++ b/arch/arm/mach-omap2/clock34xx.c @@ -725,7 +725,9 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) u32 unlock_dll = 0; u32 c; unsigned long validrate, sdrcrate, mpurate; - struct omap_sdrc_params *sp; + struct omap_sdrc_params *sdrc_cs0; + struct omap_sdrc_params *sdrc_cs1; + int ret; if (!clk || !rate) return -EINVAL; @@ -743,8 +745,8 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) else sdrcrate >>= ((clk->rate / rate) >> 1); - sp = omap2_sdrc_get_params(sdrcrate); - if (!sp) + ret = omap2_sdrc_get_params(sdrcrate, &sdrc_cs0, &sdrc_cs1); + if (ret) return -EINVAL; if (sdrcrate < MIN_SDRC_DLL_LOCK_FREQ) { @@ -765,12 +767,29 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) pr_debug("clock: changing CORE DPLL rate from %lu to %lu\n", clk->rate, validrate); - pr_debug("clock: SDRC timing params used: %08x %08x %08x\n", - sp->rfr_ctrl, sp->actim_ctrla, sp->actim_ctrlb); - - omap3_configure_core_dpll(sp->rfr_ctrl, sp->actim_ctrla, - sp->actim_ctrlb, new_div, unlock_dll, c, - sp->mr, rate > clk->rate); + pr_debug("clock: SDRC CS0 timing params used:" + " RFR %08x CTRLA %08x CTRLB %08x MR %08x\n", + sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla, + sdrc_cs0->actim_ctrlb, sdrc_cs0->mr); + if (sdrc_cs1) + pr_debug("clock: SDRC CS1 timing params used: " + " RFR %08x CTRLA %08x CTRLB %08x MR %08x\n", + sdrc_cs1->rfr_ctrl, sdrc_cs1->actim_ctrla, + sdrc_cs1->actim_ctrlb, sdrc_cs1->mr); + + if (sdrc_cs1) + omap3_configure_core_dpll( + new_div, unlock_dll, c, rate > clk->rate, + sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla, + sdrc_cs0->actim_ctrlb, sdrc_cs0->mr, + sdrc_cs1->rfr_ctrl, sdrc_cs1->actim_ctrla, + sdrc_cs1->actim_ctrlb, sdrc_cs1->mr); + else + omap3_configure_core_dpll( + new_div, unlock_dll, c, rate > clk->rate, + sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla, + sdrc_cs0->actim_ctrlb, sdrc_cs0->mr, + 0, 0, 0, 0); return 0; } diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c index 3a86b0f6603..e9b9bcb19b4 100644 --- a/arch/arm/mach-omap2/io.c +++ b/arch/arm/mach-omap2/io.c @@ -276,14 +276,15 @@ static int __init _omap2_init_reprogram_sdrc(void) return v; } -void __init omap2_init_common_hw(struct omap_sdrc_params *sp) +void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0, + struct omap_sdrc_params *sdrc_cs1) { omap2_mux_init(); #ifndef CONFIG_ARCH_OMAP4 /* FIXME: Remove this once the clkdev is ready */ pwrdm_init(powerdomains_omap); clkdm_init(clockdomains_omap, clkdm_pwrdm_autodeps); omap2_clk_init(); - omap2_sdrc_init(sp); + omap2_sdrc_init(sdrc_cs0, sdrc_cs1); _omap2_init_reprogram_sdrc(); #endif gpmc_init(); diff --git a/arch/arm/mach-omap2/sdrc.c b/arch/arm/mach-omap2/sdrc.c index 2045441e838..2e9e38db30e 100644 --- a/arch/arm/mach-omap2/sdrc.c +++ b/arch/arm/mach-omap2/sdrc.c @@ -32,7 +32,7 @@ #include #include "sdrc.h" -static struct omap_sdrc_params *sdrc_init_params; +static struct omap_sdrc_params *sdrc_init_params_cs0, *sdrc_init_params_cs1; void __iomem *omap2_sdrc_base; void __iomem *omap2_sms_base; @@ -45,33 +45,49 @@ void __iomem *omap2_sms_base; /** * omap2_sdrc_get_params - return SDRC register values for a given clock rate * @r: SDRC clock rate (in Hz) + * @sdrc_cs0: chip select 0 ram timings ** + * @sdrc_cs1: chip select 1 ram timings ** * * Return pre-calculated values for the SDRC_ACTIM_CTRLA, - * SDRC_ACTIM_CTRLB, SDRC_RFR_CTRL, and SDRC_MR registers, for a given - * SDRC clock rate 'r'. These parameters control various timing - * delays in the SDRAM controller that are expressed in terms of the - * number of SDRC clock cycles to wait; hence the clock rate - * dependency. Note that sdrc_init_params must be sorted rate - * descending. Also assumes that both chip-selects use the same - * timing parameters. Returns a struct omap_sdrc_params * upon - * success, or NULL upon failure. + * SDRC_ACTIM_CTRLB, SDRC_RFR_CTRL and SDRC_MR registers in sdrc_cs[01] + * structs,for a given SDRC clock rate 'r'. + * These parameters control various timing delays in the SDRAM controller + * that are expressed in terms of the number of SDRC clock cycles to + * wait; hence the clock rate dependency. + * + * Supports 2 different timing parameters for both chip selects. + * + * Note 1: the sdrc_init_params_cs[01] must be sorted rate descending. + * Note 2: If sdrc_init_params_cs_1 is not NULL it must be of same size + * as sdrc_init_params_cs_0. + * + * Fills in the struct omap_sdrc_params * for each chip select. + * Returns 0 upon success or -1 upon failure. */ -struct omap_sdrc_params *omap2_sdrc_get_params(unsigned long r) +int omap2_sdrc_get_params(unsigned long r, + struct omap_sdrc_params **sdrc_cs0, + struct omap_sdrc_params **sdrc_cs1) { - struct omap_sdrc_params *sp; + struct omap_sdrc_params *sp0, *sp1; - if (!sdrc_init_params) - return NULL; + if (!sdrc_init_params_cs0) + return -1; - sp = sdrc_init_params; + sp0 = sdrc_init_params_cs0; + sp1 = sdrc_init_params_cs1; - while (sp->rate && sp->rate != r) - sp++; + while (sp0->rate && sp0->rate != r) { + sp0++; + if (sdrc_init_params_cs1) + sp1++; + } - if (!sp->rate) - return NULL; + if (!sp0->rate) + return -1; - return sp; + *sdrc_cs0 = sp0; + *sdrc_cs1 = sp1; + return 0; } @@ -83,13 +99,15 @@ void __init omap2_set_globals_sdrc(struct omap_globals *omap2_globals) /** * omap2_sdrc_init - initialize SMS, SDRC devices on boot - * @sp: pointer to a null-terminated list of struct omap_sdrc_params + * @sdrc_cs[01]: pointers to a null-terminated list of struct omap_sdrc_params + * Support for 2 chip selects timings * * Turn on smart idle modes for SDRAM scheduler and controller. * Program a known-good configuration for the SDRC to deal with buggy * bootloaders. */ -void __init omap2_sdrc_init(struct omap_sdrc_params *sp) +void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0, + struct omap_sdrc_params *sdrc_cs1) { u32 l; @@ -103,7 +121,8 @@ void __init omap2_sdrc_init(struct omap_sdrc_params *sp) l |= (0x2 << 3); sdrc_write_reg(l, SDRC_SYSCONFIG); - sdrc_init_params = sp; + sdrc_init_params_cs0 = sdrc_cs0; + sdrc_init_params_cs1 = sdrc_cs1; /* XXX Enable SRFRONIDLEREQ here also? */ l = (1 << SDRC_POWER_EXTCLKDIS_SHIFT) | diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index f41f8d96ddb..3aef7448b2a 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -36,7 +36,7 @@ .text -/* r4 parameters */ +/* r1 parameters */ #define SDRC_NO_UNLOCK_DLL 0x0 #define SDRC_UNLOCK_DLL 0x1 @@ -71,40 +71,71 @@ /* * omap3_sram_configure_core_dpll - change DPLL3 M2 divider - * r0 = new SDRC_RFR_CTRL register contents - * r1 = new SDRC_ACTIM_CTRLA register contents - * r2 = new SDRC_ACTIM_CTRLB register contents - * r3 = new M2 divider setting (only 1 and 2 supported right now) - * r4 = unlock SDRC DLL? (1 = yes, 0 = no). Only unlock DLL for + * + * Params passed in registers: + * r0 = new M2 divider setting (only 1 and 2 supported right now) + * r1 = unlock SDRC DLL? (1 = yes, 0 = no). Only unlock DLL for * SDRC rates < 83MHz - * r5 = number of MPU cycles to wait for SDRC to stabilize after + * r2 = number of MPU cycles to wait for SDRC to stabilize after * reprogramming the SDRC when switching to a slower MPU speed - * r6 = new SDRC_MR_0 register value - * r7 = increasing SDRC rate? (1 = yes, 0 = no) + * r3 = increasing SDRC rate? (1 = yes, 0 = no) + * + * Params passed via the stack. The needed params will be copied in SRAM + * before use by the code in SRAM (SDRAM is not accessible during SDRC + * reconfiguration): + * new SDRC_RFR_CTRL_0 register contents + * new SDRC_ACTIM_CTRL_A_0 register contents + * new SDRC_ACTIM_CTRL_B_0 register contents + * new SDRC_MR_0 register value + * new SDRC_RFR_CTRL_1 register contents + * new SDRC_ACTIM_CTRL_A_1 register contents + * new SDRC_ACTIM_CTRL_B_1 register contents + * new SDRC_MR_1 register value * + * If the param SDRC_RFR_CTRL_1 is 0, the parameters + * are not programmed into the SDRC CS1 registers */ ENTRY(omap3_sram_configure_core_dpll) stmfd sp!, {r1-r12, lr} @ store regs to stack - ldr r4, [sp, #52] @ pull extra args off the stack - ldr r5, [sp, #56] @ load extra args from the stack - ldr r6, [sp, #60] @ load extra args from the stack - ldr r7, [sp, #64] @ load extra args from the stack + + @ pull the extra args off the stack + @ and store them in SRAM + ldr r4, [sp, #52] + str r4, omap_sdrc_rfr_ctrl_0_val + ldr r4, [sp, #56] + str r4, omap_sdrc_actim_ctrl_a_0_val + ldr r4, [sp, #60] + str r4, omap_sdrc_actim_ctrl_b_0_val + ldr r4, [sp, #64] + str r4, omap_sdrc_mr_0_val + ldr r4, [sp, #68] + str r4, omap_sdrc_rfr_ctrl_1_val + cmp r4, #0 @ if SDRC_RFR_CTRL_1 is 0, + beq skip_cs1_params @ do not use cs1 params + ldr r4, [sp, #72] + str r4, omap_sdrc_actim_ctrl_a_1_val + ldr r4, [sp, #76] + str r4, omap_sdrc_actim_ctrl_b_1_val + ldr r4, [sp, #80] + str r4, omap_sdrc_mr_1_val +skip_cs1_params: dsb @ flush buffered writes to interconnect - cmp r7, #1 @ if increasing SDRC clk rate, + + cmp r3, #1 @ if increasing SDRC clk rate, bleq configure_sdrc @ program the SDRC regs early (for RFR) - cmp r4, #SDRC_UNLOCK_DLL @ set the intended DLL state + cmp r1, #SDRC_UNLOCK_DLL @ set the intended DLL state bleq unlock_dll blne lock_dll bl sdram_in_selfrefresh @ put SDRAM in self refresh, idle SDRC bl configure_core_dpll @ change the DPLL3 M2 divider bl enable_sdrc @ take SDRC out of idle - cmp r4, #SDRC_UNLOCK_DLL @ wait for DLL status to change + cmp r1, #SDRC_UNLOCK_DLL @ wait for DLL status to change bleq wait_dll_unlock blne wait_dll_lock - cmp r7, #1 @ if increasing SDRC clk rate, + cmp r3, #1 @ if increasing SDRC clk rate, beq return_to_sdram @ return to SDRAM code, otherwise, bl configure_sdrc @ reprogram SDRC regs now - mov r12, r5 + mov r12, r2 bl wait_clk_stable @ wait for SDRC to stabilize return_to_sdram: isb @ prevent speculative exec past here @@ -149,7 +180,7 @@ configure_core_dpll: ldr r12, [r11] ldr r10, core_m2_mask_val @ modify m2 for core dpll and r12, r12, r10 - orr r12, r12, r3, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT + orr r12, r12, r0, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT str r12, [r11] ldr r12, [r11] @ posted-write barrier for CM bx lr @@ -187,15 +218,34 @@ wait_dll_unlock: bne wait_dll_unlock bx lr configure_sdrc: - ldr r11, omap3_sdrc_rfr_ctrl - str r0, [r11] - ldr r11, omap3_sdrc_actim_ctrla - str r1, [r11] - ldr r11, omap3_sdrc_actim_ctrlb - str r2, [r11] + ldr r12, omap_sdrc_rfr_ctrl_0_val @ fetch value from SRAM + ldr r11, omap3_sdrc_rfr_ctrl_0 @ fetch addr from SRAM + str r12, [r11] @ store + ldr r12, omap_sdrc_actim_ctrl_a_0_val + ldr r11, omap3_sdrc_actim_ctrl_a_0 + str r12, [r11] + ldr r12, omap_sdrc_actim_ctrl_b_0_val + ldr r11, omap3_sdrc_actim_ctrl_b_0 + str r12, [r11] + ldr r12, omap_sdrc_mr_0_val ldr r11, omap3_sdrc_mr_0 - str r6, [r11] - ldr r6, [r11] @ posted-write barrier for SDRC + str r12, [r11] + ldr r12, omap_sdrc_rfr_ctrl_1_val + cmp r12, #0 @ if SDRC_RFR_CTRL_1 is 0, + beq skip_cs1_prog @ do not program cs1 params + ldr r11, omap3_sdrc_rfr_ctrl_1 + str r12, [r11] + ldr r12, omap_sdrc_actim_ctrl_a_1_val + ldr r11, omap3_sdrc_actim_ctrl_a_1 + str r12, [r11] + ldr r12, omap_sdrc_actim_ctrl_b_1_val + ldr r11, omap3_sdrc_actim_ctrl_b_1 + str r12, [r11] + ldr r12, omap_sdrc_mr_1_val + ldr r11, omap3_sdrc_mr_1 + str r12, [r11] +skip_cs1_prog: + ldr r12, [r11] @ posted-write barrier for SDRC bx lr omap3_sdrc_power: @@ -206,14 +256,40 @@ omap3_cm_idlest1_core: .word OMAP34XX_CM_REGADDR(CORE_MOD, CM_IDLEST) omap3_cm_iclken1_core: .word OMAP34XX_CM_REGADDR(CORE_MOD, CM_ICLKEN1) -omap3_sdrc_rfr_ctrl: + +omap3_sdrc_rfr_ctrl_0: .word OMAP34XX_SDRC_REGADDR(SDRC_RFR_CTRL_0) -omap3_sdrc_actim_ctrla: +omap3_sdrc_rfr_ctrl_1: + .word OMAP34XX_SDRC_REGADDR(SDRC_RFR_CTRL_1) +omap3_sdrc_actim_ctrl_a_0: .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_0) -omap3_sdrc_actim_ctrlb: +omap3_sdrc_actim_ctrl_a_1: + .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_1) +omap3_sdrc_actim_ctrl_b_0: .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_0) +omap3_sdrc_actim_ctrl_b_1: + .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_1) omap3_sdrc_mr_0: .word OMAP34XX_SDRC_REGADDR(SDRC_MR_0) +omap3_sdrc_mr_1: + .word OMAP34XX_SDRC_REGADDR(SDRC_MR_1) +omap_sdrc_rfr_ctrl_0_val: + .word 0xDEADBEEF +omap_sdrc_rfr_ctrl_1_val: + .word 0xDEADBEEF +omap_sdrc_actim_ctrl_a_0_val: + .word 0xDEADBEEF +omap_sdrc_actim_ctrl_a_1_val: + .word 0xDEADBEEF +omap_sdrc_actim_ctrl_b_0_val: + .word 0xDEADBEEF +omap_sdrc_actim_ctrl_b_1_val: + .word 0xDEADBEEF +omap_sdrc_mr_0_val: + .word 0xDEADBEEF +omap_sdrc_mr_1_val: + .word 0xDEADBEEF + omap3_sdrc_dlla_status: .word OMAP34XX_SDRC_REGADDR(SDRC_DLLA_STATUS) omap3_sdrc_dlla_ctrl: @@ -223,3 +299,4 @@ core_m2_mask_val: ENTRY(omap3_sram_configure_core_dpll_sz) .word . - omap3_sram_configure_core_dpll + diff --git a/arch/arm/plat-omap/include/mach/io.h b/arch/arm/plat-omap/include/mach/io.h index 73f483d56ca..21fb0efdda8 100644 --- a/arch/arm/plat-omap/include/mach/io.h +++ b/arch/arm/plat-omap/include/mach/io.h @@ -228,7 +228,8 @@ extern void omap1_map_common_io(void); extern void omap1_init_common_hw(void); extern void omap2_map_common_io(void); -extern void omap2_init_common_hw(struct omap_sdrc_params *sp); +extern void omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0, + struct omap_sdrc_params *sdrc_cs1); #define __arch_ioremap(p,s,t) omap_ioremap(p,s,t) #define __arch_iounmap(v) omap_iounmap(v) diff --git a/arch/arm/plat-omap/include/mach/sdrc.h b/arch/arm/plat-omap/include/mach/sdrc.h index adc73522491..0be18e4ff18 100644 --- a/arch/arm/plat-omap/include/mach/sdrc.h +++ b/arch/arm/plat-omap/include/mach/sdrc.h @@ -30,6 +30,10 @@ #define SDRC_ACTIM_CTRL_A_0 0x09c #define SDRC_ACTIM_CTRL_B_0 0x0a0 #define SDRC_RFR_CTRL_0 0x0a4 +#define SDRC_MR_1 0x0B4 +#define SDRC_ACTIM_CTRL_A_1 0x0C4 +#define SDRC_ACTIM_CTRL_B_1 0x0C8 +#define SDRC_RFR_CTRL_1 0x0D4 /* * These values represent the number of memory clock cycles between @@ -102,8 +106,11 @@ struct omap_sdrc_params { u32 mr; }; -void __init omap2_sdrc_init(struct omap_sdrc_params *sp); -struct omap_sdrc_params *omap2_sdrc_get_params(unsigned long r); +void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0, + struct omap_sdrc_params *sdrc_cs1); +int omap2_sdrc_get_params(unsigned long r, + struct omap_sdrc_params **sdrc_cs0, + struct omap_sdrc_params **sdrc_cs1); #ifdef CONFIG_ARCH_OMAP2 diff --git a/arch/arm/plat-omap/include/mach/sram.h b/arch/arm/plat-omap/include/mach/sram.h index 4d53cc59d7a..8974e3fc269 100644 --- a/arch/arm/plat-omap/include/mach/sram.h +++ b/arch/arm/plat-omap/include/mach/sram.h @@ -21,11 +21,12 @@ extern void omap2_sram_reprogram_sdrc(u32 perf_level, u32 dll_val, u32 mem_type); extern u32 omap2_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass); -extern u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, - u32 sdrc_actim_ctrla, - u32 sdrc_actim_ctrlb, u32 m2, - u32 unlock_dll, u32 f, u32 sdrc_mr, - u32 inc); +extern u32 omap3_configure_core_dpll( + u32 m2, u32 unlock_dll, u32 f, u32 inc, + u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0, + u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0, + u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1, + u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1); /* Do not use these */ extern void omap1_sram_reprogram_clock(u32 ckctl, u32 dpllctl); @@ -59,12 +60,12 @@ extern void omap243x_sram_reprogram_sdrc(u32 perf_level, u32 dll_val, u32 mem_type); extern unsigned long omap243x_sram_reprogram_sdrc_sz; - -extern u32 omap3_sram_configure_core_dpll(u32 sdrc_rfr_ctrl, - u32 sdrc_actim_ctrla, - u32 sdrc_actim_ctrlb, u32 m2, - u32 unlock_dll, u32 f, u32 sdrc_mr, - u32 inc); +extern u32 omap3_sram_configure_core_dpll( + u32 m2, u32 unlock_dll, u32 f, u32 inc, + u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0, + u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0, + u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1, + u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1); extern unsigned long omap3_sram_configure_core_dpll_sz; #endif diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c index 4ea73804d21..4e781c99f0e 100644 --- a/arch/arm/plat-omap/sram.c +++ b/arch/arm/plat-omap/sram.c @@ -373,20 +373,26 @@ static inline int omap243x_sram_init(void) #ifdef CONFIG_ARCH_OMAP3 -static u32 (*_omap3_sram_configure_core_dpll)(u32 sdrc_rfr_ctrl, - u32 sdrc_actim_ctrla, - u32 sdrc_actim_ctrlb, - u32 m2, u32 unlock_dll, - u32 f, u32 sdrc_mr, u32 inc); -u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, - u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll, - u32 f, u32 sdrc_mr, u32 inc) +static u32 (*_omap3_sram_configure_core_dpll)( + u32 m2, u32 unlock_dll, u32 f, u32 inc, + u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0, + u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0, + u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1, + u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1); + +u32 omap3_configure_core_dpll(u32 m2, u32 unlock_dll, u32 f, u32 inc, + u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0, + u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0, + u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1, + u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1) { BUG_ON(!_omap3_sram_configure_core_dpll); - return _omap3_sram_configure_core_dpll(sdrc_rfr_ctrl, - sdrc_actim_ctrla, - sdrc_actim_ctrlb, m2, - unlock_dll, f, sdrc_mr, inc); + return _omap3_sram_configure_core_dpll( + m2, unlock_dll, f, inc, + sdrc_rfr_ctrl_0, sdrc_actim_ctrl_a_0, + sdrc_actim_ctrl_b_0, sdrc_mr_0, + sdrc_rfr_ctrl_1, sdrc_actim_ctrl_a_1, + sdrc_actim_ctrl_b_1, sdrc_mr_1); } /* REVISIT: Should this be same as omap34xx_sram_init() after off-idle? */ -- GitLab From 9fb97412c3be5d0d1dd0e9d7c5268469e4c942aa Mon Sep 17 00:00:00 2001 From: Jean Pihet Date: Fri, 24 Jul 2009 19:43:25 -0600 Subject: [PATCH 0316/1342] OMAP3: Setup MUX settings for SDRC CKE signals This patches ensures the MUX settings are correct for the SDRC CKE signals to SDRAM. This allows the self-refresh to work when 2 chip-selects are in use. A warning is thrown away in case the initial muxing is incorrect, in order to track faulty or old-dated bootloaders. Note: The CONFIG_OMAP_MUX and CONFIG_OMAP_MUX_WARNINGS options must be enabled for the mux code to have effect. Signed-off-by: Jean Pihet Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/board-omap3beagle.c | 4 ++++ arch/arm/mach-omap2/board-omap3pandora.c | 5 +++++ arch/arm/mach-omap2/board-overo.c | 5 +++++ arch/arm/mach-omap2/board-rx51.c | 4 ++++ arch/arm/mach-omap2/mux.c | 6 ++++++ arch/arm/plat-omap/include/mach/mux.h | 4 ++++ 6 files changed, 28 insertions(+) diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 4abefd9566e..e00ba128cec 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -409,6 +409,10 @@ static void __init omap3_beagle_init(void) usb_musb_init(); omap3beagle_flash_init(); + + /* Ensure SDRC pins are mux'd for self-refresh */ + omap_cfg_reg(H16_34XX_SDRC_CKE0); + omap_cfg_reg(H17_34XX_SDRC_CKE1); } static void __init omap3_beagle_map_io(void) diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c index 9b991ced382..864ee3d021f 100644 --- a/arch/arm/mach-omap2/board-omap3pandora.c +++ b/arch/arm/mach-omap2/board-omap3pandora.c @@ -40,6 +40,7 @@ #include #include #include +#include #include "sdram-micron-mt46h32m32lf-6.h" #include "mmc-twl4030.h" @@ -398,6 +399,10 @@ static void __init omap3pandora_init(void) omap3pandora_ads7846_init(); pandora_keys_gpio_init(); usb_musb_init(); + + /* Ensure SDRC pins are mux'd for self-refresh */ + omap_cfg_reg(H16_34XX_SDRC_CKE0); + omap_cfg_reg(H17_34XX_SDRC_CKE1); } static void __init omap3pandora_map_io(void) diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index 44bc1c54cd0..6b171b338ec 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -44,6 +44,7 @@ #include #include #include +#include #include #include "sdram-micron-mt46h32m32lf-6.h" @@ -396,6 +397,10 @@ static void __init overo_init(void) overo_ads7846_init(); overo_init_smsc911x(); + /* Ensure SDRC pins are mux'd for self-refresh */ + omap_cfg_reg(H16_34XX_SDRC_CKE0); + omap_cfg_reg(H17_34XX_SDRC_CKE1); + if ((gpio_request(OVERO_GPIO_W2W_NRESET, "OVERO_GPIO_W2W_NRESET") == 0) && (gpio_direction_output(OVERO_GPIO_W2W_NRESET, 1) == 0)) { diff --git a/arch/arm/mach-omap2/board-rx51.c b/arch/arm/mach-omap2/board-rx51.c index 591ae8a5805..1c9e07fe826 100644 --- a/arch/arm/mach-omap2/board-rx51.c +++ b/arch/arm/mach-omap2/board-rx51.c @@ -75,6 +75,10 @@ static void __init rx51_init(void) omap_serial_init(); usb_musb_init(); rx51_peripherals_init(); + + /* Ensure SDRC pins are mux'd for self-refresh */ + omap_cfg_reg(H16_34XX_SDRC_CKE0); + omap_cfg_reg(H17_34XX_SDRC_CKE1); } static void __init rx51_map_io(void) diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c index 026c4fc883a..43d6b92b65f 100644 --- a/arch/arm/mach-omap2/mux.c +++ b/arch/arm/mach-omap2/mux.c @@ -486,6 +486,12 @@ MUX_CFG_34XX("H19_34XX_GPIO164_OUT", 0x19c, OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT) MUX_CFG_34XX("J25_34XX_GPIO170", 0x1c6, OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT) + +/* OMAP3 SDRC CKE signals to SDR/DDR ram chips */ +MUX_CFG_34XX("H16_34XX_SDRC_CKE0", 0x262, + OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT) +MUX_CFG_34XX("H17_34XX_SDRC_CKE1", 0x264, + OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT) }; #define OMAP34XX_PINS_SZ ARRAY_SIZE(omap34xx_pins) diff --git a/arch/arm/plat-omap/include/mach/mux.h b/arch/arm/plat-omap/include/mach/mux.h index 85a62170576..80281c458ba 100644 --- a/arch/arm/plat-omap/include/mach/mux.h +++ b/arch/arm/plat-omap/include/mach/mux.h @@ -853,6 +853,10 @@ enum omap34xx_index { AE5_34XX_GPIO143, H19_34XX_GPIO164_OUT, J25_34XX_GPIO170, + + /* OMAP3 SDRC CKE signals to SDR/DDR ram chips */ + H16_34XX_SDRC_CKE0, + H17_34XX_SDRC_CKE1, }; struct omap_mux_cfg { -- GitLab From 75f251e3d0803b028f3474fdc75be0994c377ab5 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 24 Jul 2009 19:44:01 -0600 Subject: [PATCH 0317/1342] OMAP2/3 SDRC: don't set SDRC_POWER.PWDENA on boot Stop setting SDRC_POWER.PWDENA on boot. There is a nasty erratum (34xx erratum 1.150) that can cause memory corruption if PWDENA is enabled. Based originally on a patch from Samu P. Onkalo . Tested on BeagleBoard rev C2. Signed-off-by: Paul Walmsley Cc: Samu P. Onkalo --- arch/arm/mach-omap2/sdrc.c | 5 ++++- arch/arm/mach-omap2/sram34xx.S | 2 -- 2 files changed, 4 insertions(+), 3 deletions(-) diff --git a/arch/arm/mach-omap2/sdrc.c b/arch/arm/mach-omap2/sdrc.c index 2e9e38db30e..9e3bd4fa781 100644 --- a/arch/arm/mach-omap2/sdrc.c +++ b/arch/arm/mach-omap2/sdrc.c @@ -125,8 +125,11 @@ void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0, sdrc_init_params_cs1 = sdrc_cs1; /* XXX Enable SRFRONIDLEREQ here also? */ + /* + * PWDENA should not be set due to 34xx erratum 1.150 - PWDENA + * can cause random memory corruption + */ l = (1 << SDRC_POWER_EXTCLKDIS_SHIFT) | - (1 << SDRC_POWER_PWDENA_SHIFT) | (1 << SDRC_POWER_PAGEPOLICY_SHIFT); sdrc_write_reg(l, SDRC_POWER); } diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index 3aef7448b2a..9c2d0465a83 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -58,7 +58,6 @@ /* SDRC_POWER bit settings */ #define SRFRONIDLEREQ_MASK 0x40 -#define PWDENA_MASK 0x4 /* CM_IDLEST1_CORE bit settings */ #define ST_SDRC_MASK 0x2 @@ -160,7 +159,6 @@ sdram_in_selfrefresh: ldr r12, [r11] @ read the contents of SDRC_POWER mov r9, r12 @ keep a copy of SDRC_POWER bits orr r12, r12, #SRFRONIDLEREQ_MASK @ enable self refresh on idle - bic r12, r12, #PWDENA_MASK @ clear PWDENA str r12, [r11] @ write back to SDRC_POWER register ldr r12, [r11] @ posted-write barrier for SDRC idle_sdrc: -- GitLab From 8ff120e5303e27e03aba7b774e86fd43eaf90376 Mon Sep 17 00:00:00 2001 From: Rajendra Nayak Date: Fri, 24 Jul 2009 19:44:01 -0600 Subject: [PATCH 0318/1342] OMAP3 SDRC: Fix freeze when scaling CORE dpll to < 83Mhz This patch fixes a bug in the CORE dpll scaling sequence which was errouneously clearing some bits in the SDRC DLLA CTRL register and hence causing a freeze. The issue was observed only on platforms which scale CORE dpll to < 83Mhz and hence program the DLL in fixed delay mode. Issue reported by Limei Wang , with debugging assistance from Richard Woodruff and Girish Ghongdemath . Signed-off-by: Rajendra Nayak Cc: Limei Wang Cc: Richard Woodruff Cc: Girish Ghongdemath Signed-off-by: Paul Walmsley [paul@pwsan.com: updated patch description to include collaboration credits] --- arch/arm/mach-omap2/sram34xx.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index 9c2d0465a83..e6b112590d7 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -143,7 +143,7 @@ return_to_sdram: unlock_dll: ldr r11, omap3_sdrc_dlla_ctrl ldr r12, [r11] - and r12, r12, #FIXEDDELAY_MASK + bic r12, r12, #FIXEDDELAY_MASK orr r12, r12, #FIXEDDELAY_DEFAULT orr r12, r12, #DLLIDLE_MASK str r12, [r11] @ (no OCP barrier needed) -- GitLab From df56556e571234cf26072cd58c01ac3520986b44 Mon Sep 17 00:00:00 2001 From: Rajendra Nayak Date: Fri, 24 Jul 2009 19:44:02 -0600 Subject: [PATCH 0319/1342] OMAP3 SDRC: Move the clk stabilization delay to the right place The clock stabilization delay post a M2 divider change is needed even before a SDRC interface clock re-enable and not only before jumping back to SDRAM. Signed-off-by: Rajendra Nayak Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/sram34xx.S | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index e6b112590d7..82aa4a3d160 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -127,6 +127,8 @@ skip_cs1_params: blne lock_dll bl sdram_in_selfrefresh @ put SDRAM in self refresh, idle SDRC bl configure_core_dpll @ change the DPLL3 M2 divider + mov r12, r2 + bl wait_clk_stable @ wait for SDRC to stabilize bl enable_sdrc @ take SDRC out of idle cmp r1, #SDRC_UNLOCK_DLL @ wait for DLL status to change bleq wait_dll_unlock @@ -134,8 +136,6 @@ skip_cs1_params: cmp r3, #1 @ if increasing SDRC clk rate, beq return_to_sdram @ return to SDRAM code, otherwise, bl configure_sdrc @ reprogram SDRC regs now - mov r12, r2 - bl wait_clk_stable @ wait for SDRC to stabilize return_to_sdram: isb @ prevent speculative exec past here mov r0, #0 @ return value -- GitLab From 72350b29a4c0debfc27c2edbeed9b4ff3f935dd4 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 24 Jul 2009 19:44:03 -0600 Subject: [PATCH 0320/1342] OMAP2/3 clock: split, rename omap2_wait_clock_ready() Some OMAP2/3 hardware modules have CM_IDLEST attributes that are not handled by the current omap2_wait_clock_ready() code. In preparation for patches that fix the unusual devices, rename the function omap2_wait_clock_ready() to omap2_wait_module_ready() and split it into three parts: 1. A clkops-specific companion clock return function (by default, omap2_clk_dflt_find_companion()) 2. A clkops-specific CM_IDLEST register address and bit shift return function (by default, omap2_clk_dflt_find_idlest()) 3. Code to wait for the CM to indicate that the module is ready (omap2_cm_wait_idlest()) Clocks can now specify their own custom find_companion() and find_idlest() functions; used in subsequent patches. Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/clock.c | 156 ++++++++++++------------ arch/arm/mach-omap2/clock.h | 6 + arch/arm/mach-omap2/prcm.c | 43 +++++++ arch/arm/plat-omap/include/mach/clock.h | 2 + arch/arm/plat-omap/include/mach/prcm.h | 1 + 5 files changed, 131 insertions(+), 77 deletions(-) diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c index b0665f161c0..456e2ad5f62 100644 --- a/arch/arm/mach-omap2/clock.c +++ b/arch/arm/mach-omap2/clock.c @@ -27,6 +27,7 @@ #include #include #include +#include #include #include @@ -38,8 +39,6 @@ #include "cm-regbits-24xx.h" #include "cm-regbits-34xx.h" -#define MAX_CLOCK_ENABLE_WAIT 100000 - /* DPLL rate rounding: minimum DPLL multiplier, divider values */ #define DPLL_MIN_MULTIPLIER 1 #define DPLL_MIN_DIVIDER 1 @@ -274,83 +273,97 @@ unsigned long omap2_fixed_divisor_recalc(struct clk *clk) } /** - * omap2_wait_clock_ready - wait for clock to enable - * @reg: physical address of clock IDLEST register - * @mask: value to mask against to determine if the clock is active - * @name: name of the clock (for printk) + * omap2_clk_dflt_find_companion - find companion clock to @clk + * @clk: struct clk * to find the companion clock of + * @other_reg: void __iomem ** to return the companion clock CM_*CLKEN va in + * @other_bit: u8 ** to return the companion clock bit shift in + * + * Note: We don't need special code here for INVERT_ENABLE for the + * time being since INVERT_ENABLE only applies to clocks enabled by + * CM_CLKEN_PLL * - * Returns 1 if the clock enabled in time, or 0 if it failed to enable - * in roughly MAX_CLOCK_ENABLE_WAIT microseconds. + * Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes it's + * just a matter of XORing the bits. + * + * Some clocks don't have companion clocks. For example, modules with + * only an interface clock (such as MAILBOXES) don't have a companion + * clock. Right now, this code relies on the hardware exporting a bit + * in the correct companion register that indicates that the + * nonexistent 'companion clock' is active. Future patches will + * associate this type of code with per-module data structures to + * avoid this issue, and remove the casts. No return value. */ -int omap2_wait_clock_ready(void __iomem *reg, u32 mask, const char *name) +void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg, + u8 *other_bit) { - int i = 0; - int ena = 0; + u32 r; /* - * 24xx uses 0 to indicate not ready, and 1 to indicate ready. - * 34xx reverses this, just to keep us on our toes + * Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes + * it's just a matter of XORing the bits. */ - if (cpu_mask & (RATE_IN_242X | RATE_IN_243X)) - ena = mask; - else if (cpu_mask & RATE_IN_343X) - ena = 0; - - /* Wait for lock */ - while (((__raw_readl(reg) & mask) != ena) && - (i++ < MAX_CLOCK_ENABLE_WAIT)) { - udelay(1); - } - - if (i <= MAX_CLOCK_ENABLE_WAIT) - pr_debug("Clock %s stable after %d loops\n", name, i); - else - printk(KERN_ERR "Clock %s didn't enable in %d tries\n", - name, MAX_CLOCK_ENABLE_WAIT); - - - return (i < MAX_CLOCK_ENABLE_WAIT) ? 1 : 0; -}; + r = ((__force u32)clk->enable_reg ^ (CM_FCLKEN ^ CM_ICLKEN)); + *other_reg = (__force void __iomem *)r; + *other_bit = clk->enable_bit; +} -/* - * Note: We don't need special code here for INVERT_ENABLE - * for the time being since INVERT_ENABLE only applies to clocks enabled by - * CM_CLKEN_PLL +/** + * omap2_clk_dflt_find_idlest - find CM_IDLEST reg va, bit shift for @clk + * @clk: struct clk * to find IDLEST info for + * @idlest_reg: void __iomem ** to return the CM_IDLEST va in + * @idlest_bit: u8 ** to return the CM_IDLEST bit shift in + * + * Return the CM_IDLEST register address and bit shift corresponding + * to the module that "owns" this clock. This default code assumes + * that the CM_IDLEST bit shift is the CM_*CLKEN bit shift, and that + * the IDLEST register address ID corresponds to the CM_*CLKEN + * register address ID (e.g., that CM_FCLKEN2 corresponds to + * CM_IDLEST2). This is not true for all modules. No return value. */ -static void omap2_clk_wait_ready(struct clk *clk) +void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg, + u8 *idlest_bit) { - void __iomem *reg, *other_reg, *st_reg; - u32 bit; + u32 r; - /* - * REVISIT: This code is pretty ugly. It would be nice to generalize - * it and pull it into struct clk itself somehow. - */ - reg = clk->enable_reg; + r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); + *idlest_reg = (__force void __iomem *)r; + *idlest_bit = clk->enable_bit; +} - /* - * Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes - * it's just a matter of XORing the bits. - */ - other_reg = (void __iomem *)((u32)reg ^ (CM_FCLKEN ^ CM_ICLKEN)); +/** + * omap2_module_wait_ready - wait for an OMAP module to leave IDLE + * @clk: struct clk * belonging to the module + * + * If the necessary clocks for the OMAP hardware IP block that + * corresponds to clock @clk are enabled, then wait for the module to + * indicate readiness (i.e., to leave IDLE). This code does not + * belong in the clock code and will be moved in the medium term to + * module-dependent code. No return value. + */ +static void omap2_module_wait_ready(struct clk *clk) +{ + void __iomem *companion_reg, *idlest_reg; + u8 other_bit, idlest_bit; + + /* Not all modules have multiple clocks that their IDLEST depends on */ + if (clk->ops->find_companion) { + clk->ops->find_companion(clk, &companion_reg, &other_bit); + if (!(__raw_readl(companion_reg) & (1 << other_bit))) + return; + } - /* Check if both functional and interface clocks - * are running. */ - bit = 1 << clk->enable_bit; - if (!(__raw_readl(other_reg) & bit)) - return; - st_reg = (void __iomem *)(((u32)other_reg & ~0xf0) | 0x20); /* CM_IDLEST* */ + clk->ops->find_idlest(clk, &idlest_reg, &idlest_bit); - omap2_wait_clock_ready(st_reg, bit, clk->name); + omap2_cm_wait_idlest(idlest_reg, (1 << idlest_bit), clk->name); } -static int omap2_dflt_clk_enable(struct clk *clk) +int omap2_dflt_clk_enable(struct clk *clk) { u32 v; if (unlikely(clk->enable_reg == NULL)) { - printk(KERN_ERR "clock.c: Enable for %s without enable code\n", + pr_err("clock.c: Enable for %s without enable code\n", clk->name); return 0; /* REVISIT: -EINVAL */ } @@ -363,26 +376,13 @@ static int omap2_dflt_clk_enable(struct clk *clk) __raw_writel(v, clk->enable_reg); v = __raw_readl(clk->enable_reg); /* OCP barrier */ - return 0; -} + if (clk->ops->find_idlest) + omap2_module_wait_ready(clk); -static int omap2_dflt_clk_enable_wait(struct clk *clk) -{ - int ret; - - if (!clk->enable_reg) { - printk(KERN_ERR "clock.c: Enable for %s without enable code\n", - clk->name); - return 0; /* REVISIT: -EINVAL */ - } - - ret = omap2_dflt_clk_enable(clk); - if (ret == 0) - omap2_clk_wait_ready(clk); - return ret; + return 0; } -static void omap2_dflt_clk_disable(struct clk *clk) +void omap2_dflt_clk_disable(struct clk *clk) { u32 v; @@ -406,8 +406,10 @@ static void omap2_dflt_clk_disable(struct clk *clk) } const struct clkops clkops_omap2_dflt_wait = { - .enable = omap2_dflt_clk_enable_wait, + .enable = omap2_dflt_clk_enable, .disable = omap2_dflt_clk_disable, + .find_companion = omap2_clk_dflt_find_companion, + .find_idlest = omap2_clk_dflt_find_idlest, }; const struct clkops clkops_omap2_dflt = { diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index 2679ddfa642..9ae7540f8af 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -65,6 +65,12 @@ int omap2_clksel_set_rate(struct clk *clk, unsigned long rate); u32 omap2_get_dpll_rate(struct clk *clk); int omap2_wait_clock_ready(void __iomem *reg, u32 cval, const char *name); void omap2_clk_prepare_for_reboot(void); +int omap2_dflt_clk_enable(struct clk *clk); +void omap2_dflt_clk_disable(struct clk *clk); +void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg, + u8 *other_bit); +void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg, + u8 *idlest_bit); extern const struct clkops clkops_omap2_dflt_wait; extern const struct clkops clkops_omap2_dflt; diff --git a/arch/arm/mach-omap2/prcm.c b/arch/arm/mach-omap2/prcm.c index f945156d558..ced555a4cd1 100644 --- a/arch/arm/mach-omap2/prcm.c +++ b/arch/arm/mach-omap2/prcm.c @@ -17,6 +17,7 @@ #include #include #include +#include #include #include @@ -28,6 +29,8 @@ static void __iomem *prm_base; static void __iomem *cm_base; +#define MAX_MODULE_ENABLE_WAIT 100000 + u32 omap_prcm_get_reset_sources(void) { /* XXX This presumably needs modification for 34XX */ @@ -120,6 +123,46 @@ u32 cm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx) } EXPORT_SYMBOL(cm_rmw_mod_reg_bits); +/** + * omap2_cm_wait_idlest - wait for IDLEST bit to indicate module readiness + * @reg: physical address of module IDLEST register + * @mask: value to mask against to determine if the module is active + * @name: name of the clock (for printk) + * + * Returns 1 if the module indicated readiness in time, or 0 if it + * failed to enable in roughly MAX_MODULE_ENABLE_WAIT microseconds. + */ +int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, const char *name) +{ + int i = 0; + int ena = 0; + + /* + * 24xx uses 0 to indicate not ready, and 1 to indicate ready. + * 34xx reverses this, just to keep us on our toes + */ + if (cpu_is_omap24xx()) + ena = mask; + else if (cpu_is_omap34xx()) + ena = 0; + else + BUG(); + + /* Wait for lock */ + while (((__raw_readl(reg) & mask) != ena) && + (i++ < MAX_MODULE_ENABLE_WAIT)) + udelay(1); + + if (i < MAX_MODULE_ENABLE_WAIT) + pr_debug("cm: Module associated with clock %s ready after %d " + "loops\n", name, i); + else + pr_err("cm: Module associated with clock %s didn't enable in " + "%d tries\n", name, MAX_MODULE_ENABLE_WAIT); + + return (i < MAX_MODULE_ENABLE_WAIT) ? 1 : 0; +}; + void __init omap2_set_globals_prcm(struct omap_globals *omap2_globals) { prm_base = omap2_globals->prm; diff --git a/arch/arm/plat-omap/include/mach/clock.h b/arch/arm/plat-omap/include/mach/clock.h index f9f65e1ba3f..4b8b0d65cbf 100644 --- a/arch/arm/plat-omap/include/mach/clock.h +++ b/arch/arm/plat-omap/include/mach/clock.h @@ -20,6 +20,8 @@ struct clockdomain; struct clkops { int (*enable)(struct clk *); void (*disable)(struct clk *); + void (*find_idlest)(struct clk *, void __iomem **, u8 *); + void (*find_companion)(struct clk *, void __iomem **, u8 *); }; #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) || \ diff --git a/arch/arm/plat-omap/include/mach/prcm.h b/arch/arm/plat-omap/include/mach/prcm.h index 24ac3c71591..cda2a70397b 100644 --- a/arch/arm/plat-omap/include/mach/prcm.h +++ b/arch/arm/plat-omap/include/mach/prcm.h @@ -25,6 +25,7 @@ u32 omap_prcm_get_reset_sources(void); void omap_prcm_arch_reset(char mode); +int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, const char *name); #endif -- GitLab From 3dc2197579089c5b74c7fba666c8ccf1a449afb4 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 24 Jul 2009 19:44:04 -0600 Subject: [PATCH 0321/1342] OMAP2 clock: 2430 I2CHS uses non-standard CM_IDLEST register OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the CM_*CLKEN bits are in CM_{I,F}CLKEN2_CORE [1]. Fix by implementing a custom clkops .find_idlest function to return the correct slave IDLEST register. ... 1. OMAP2430 Multimedia Device Package-on-Package (POP) Silicon Revision 2.1 (Rev. V) Technical Reference Manual, tables 4-99 and 4-105. Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/clock24xx.c | 37 +++++++++++++++++++++++++++++++-- arch/arm/mach-omap2/clock24xx.h | 4 ++-- 2 files changed, 37 insertions(+), 4 deletions(-) diff --git a/arch/arm/mach-omap2/clock24xx.c b/arch/arm/mach-omap2/clock24xx.c index 44de0271fc2..bc5d3ac6661 100644 --- a/arch/arm/mach-omap2/clock24xx.c +++ b/arch/arm/mach-omap2/clock24xx.c @@ -30,6 +30,7 @@ #include #include +#include #include #include @@ -43,6 +44,18 @@ static const struct clkops clkops_oscck; static const struct clkops clkops_fixed; +static void omap2430_clk_i2chs_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit); + +/* 2430 I2CHS has non-standard IDLEST register */ +static const struct clkops clkops_omap2430_i2chs_wait = { + .enable = omap2_dflt_clk_enable, + .disable = omap2_dflt_clk_disable, + .find_idlest = omap2430_clk_i2chs_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + #include "clock24xx.h" struct omap_clk { @@ -239,6 +252,26 @@ static void __iomem *prcm_clksrc_ctrl; * Omap24xx specific clock functions *-------------------------------------------------------------------------*/ +/** + * omap2430_clk_i2chs_find_idlest - return CM_IDLEST info for 2430 I2CHS + * @clk: struct clk * being enabled + * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into + * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into + * + * OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the + * CM_*CLKEN bits are in CM_{I,F}CLKEN2_CORE. This custom function + * passes back the correct CM_IDLEST register address for I2CHS + * modules. No return value. + */ +static void omap2430_clk_i2chs_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit) +{ + *idlest_reg = OMAP_CM_REGADDR(CORE_MOD, CM_IDLEST); + *idlest_bit = clk->enable_bit; +} + + /** * omap2xxx_clk_get_core_rate - return the CORE_CLK rate * @clk: pointer to the combined dpll_ck + core_ck (currently "dpll_ck") @@ -325,8 +358,8 @@ static int omap2_clk_fixed_enable(struct clk *clk) else if (clk == &apll54_ck) cval = OMAP24XX_ST_54M_APLL; - omap2_wait_clock_ready(OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), cval, - clk->name); + omap2_cm_wait_idlest(OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), cval, + clk->name); /* * REVISIT: Should we return an error code if omap2_wait_clock_ready() diff --git a/arch/arm/mach-omap2/clock24xx.h b/arch/arm/mach-omap2/clock24xx.h index 458f00cdcbe..d19cf7a7d8d 100644 --- a/arch/arm/mach-omap2/clock24xx.h +++ b/arch/arm/mach-omap2/clock24xx.h @@ -2337,7 +2337,7 @@ static struct clk i2c2_fck = { static struct clk i2chs2_fck = { .name = "i2c_fck", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap2430_i2chs_wait, .id = 2, .parent = &func_96m_ck, .clkdm_name = "core_l4_clkdm", @@ -2370,7 +2370,7 @@ static struct clk i2c1_fck = { static struct clk i2chs1_fck = { .name = "i2c_fck", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap2430_i2chs_wait, .id = 1, .parent = &func_96m_ck, .clkdm_name = "core_l4_clkdm", -- GitLab From 3c82e229f09a6acc8d24dc27c5e0e60b1d7161c2 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 24 Jul 2009 19:44:06 -0600 Subject: [PATCH 0322/1342] OMAP3 clock: correct module IDLEST bits: SSI; DSS; USBHOST; HSOTGUSB Fix two bugs in the OMAP3 clock tree pertaining to the SSI, DSS, USBHOST, and HSOTGUSB devices. These devices are both interconnect initiators and targets. Without this patch, clk_enable()s on clocks for these modules can be very high latency (potentially up to ~200 milliseconds) and message such as the following are generated: Clock usbhost_48m_fck didn't enable in 100000 tries Two bugs are fixed by this patch. First, OMAP hardware only supports target CM_IDLEST register bits on ES2+ chips and beyond. ES1 chips should not wait for these clocks to enable. So, split the appropriate clocks into ES1 and ES2+ variants, so that kernels running on ES1 devices won't try to wait. Second, the current heuristic in omap2_clk_dflt_find_idlest() will fail for these clocks. It assumes that the CM_IDLEST bit to wait upon is the same as the CM_*CLKEN bit, which is false[1]. Fix by implementing custom clkops .find_idlest function pointers for the appropriate clocks that return the correct slave IDLEST bit shift. This was originally fixed in the linux-omap kernel during 2.6.29 in a slightly different manner[2][3]. In the medium-term future, all of the module IDLEST code will eventually be moved to the omap_hwmod code. Problem reported by Jarkko Nikula : http://marc.info/?l=linux-omap&m=124306184903679&w=2 ... 1. See for example 34xx TRM Revision P Table 4-213 and 4-217 (for the DSS case). 2. http://www.spinics.net/lists/linux-omap/msg05512.html et seq. 3. http://lkml.indiana.edu/hypermail/linux/kernel/0901.3/01498.html Signed-off-by: Paul Walmsley Cc: Jarkko Nikula --- arch/arm/mach-omap2/clock34xx.c | 118 ++++++++++++++++++++++++++++++-- arch/arm/mach-omap2/clock34xx.h | 85 ++++++++++++++++++++--- 2 files changed, 185 insertions(+), 18 deletions(-) diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c index 1c6480d3ad6..cd7819cc0c9 100644 --- a/arch/arm/mach-omap2/clock34xx.c +++ b/arch/arm/mach-omap2/clock34xx.c @@ -2,7 +2,7 @@ * OMAP3-specific clock framework functions * * Copyright (C) 2007-2008 Texas Instruments, Inc. - * Copyright (C) 2007-2008 Nokia Corporation + * Copyright (C) 2007-2009 Nokia Corporation * * Written by Paul Walmsley * Testing and integration fixes by Jouni Högander @@ -41,6 +41,37 @@ static const struct clkops clkops_noncore_dpll_ops; +static void omap3430es2_clk_ssi_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit); +static void omap3430es2_clk_hsotgusb_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit); +static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit); + +static const struct clkops clkops_omap3430es2_ssi_wait = { + .enable = omap2_dflt_clk_enable, + .disable = omap2_dflt_clk_disable, + .find_idlest = omap3430es2_clk_ssi_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + +static const struct clkops clkops_omap3430es2_hsotgusb_wait = { + .enable = omap2_dflt_clk_enable, + .disable = omap2_dflt_clk_disable, + .find_idlest = omap3430es2_clk_hsotgusb_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + +static const struct clkops clkops_omap3430es2_dss_usbhost_wait = { + .enable = omap2_dflt_clk_enable, + .disable = omap2_dflt_clk_disable, + .find_idlest = omap3430es2_clk_dss_usbhost_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + #include "clock34xx.h" struct omap_clk { @@ -157,10 +188,13 @@ static struct omap_clk omap34xx_clks[] = { CLK(NULL, "fshostusb_fck", &fshostusb_fck, CK_3430ES1), CLK(NULL, "core_12m_fck", &core_12m_fck, CK_343X), CLK("omap_hdq.0", "fck", &hdq_fck, CK_343X), - CLK(NULL, "ssi_ssr_fck", &ssi_ssr_fck, CK_343X), - CLK(NULL, "ssi_sst_fck", &ssi_sst_fck, CK_343X), + CLK(NULL, "ssi_ssr_fck", &ssi_ssr_fck_3430es1, CK_3430ES1), + CLK(NULL, "ssi_ssr_fck", &ssi_ssr_fck_3430es2, CK_3430ES2), + CLK(NULL, "ssi_sst_fck", &ssi_sst_fck_3430es1, CK_3430ES1), + CLK(NULL, "ssi_sst_fck", &ssi_sst_fck_3430es2, CK_3430ES2), CLK(NULL, "core_l3_ick", &core_l3_ick, CK_343X), - CLK("musb_hdrc", "ick", &hsotgusb_ick, CK_343X), + CLK("musb_hdrc", "ick", &hsotgusb_ick_3430es1, CK_3430ES1), + CLK("musb_hdrc", "ick", &hsotgusb_ick_3430es2, CK_3430ES2), CLK(NULL, "sdrc_ick", &sdrc_ick, CK_343X), CLK(NULL, "gpmc_fck", &gpmc_fck, CK_343X), CLK(NULL, "security_l3_ick", &security_l3_ick, CK_343X), @@ -193,18 +227,21 @@ static struct omap_clk omap34xx_clks[] = { CLK(NULL, "mailboxes_ick", &mailboxes_ick, CK_343X), CLK(NULL, "omapctrl_ick", &omapctrl_ick, CK_343X), CLK(NULL, "ssi_l4_ick", &ssi_l4_ick, CK_343X), - CLK(NULL, "ssi_ick", &ssi_ick, CK_343X), + CLK(NULL, "ssi_ick", &ssi_ick_3430es1, CK_3430ES1), + CLK(NULL, "ssi_ick", &ssi_ick_3430es2, CK_3430ES2), CLK(NULL, "usb_l4_ick", &usb_l4_ick, CK_3430ES1), CLK(NULL, "security_l4_ick2", &security_l4_ick2, CK_343X), CLK(NULL, "aes1_ick", &aes1_ick, CK_343X), CLK("omap_rng", "ick", &rng_ick, CK_343X), CLK(NULL, "sha11_ick", &sha11_ick, CK_343X), CLK(NULL, "des1_ick", &des1_ick, CK_343X), - CLK("omapfb", "dss1_fck", &dss1_alwon_fck, CK_343X), + CLK("omapfb", "dss1_fck", &dss1_alwon_fck_3430es1, CK_3430ES1), + CLK("omapfb", "dss1_fck", &dss1_alwon_fck_3430es2, CK_3430ES2), CLK("omapfb", "tv_fck", &dss_tv_fck, CK_343X), CLK("omapfb", "video_fck", &dss_96m_fck, CK_343X), CLK("omapfb", "dss2_fck", &dss2_alwon_fck, CK_343X), - CLK("omapfb", "ick", &dss_ick, CK_343X), + CLK("omapfb", "ick", &dss_ick_3430es1, CK_3430ES1), + CLK("omapfb", "ick", &dss_ick_3430es2, CK_3430ES2), CLK(NULL, "cam_mclk", &cam_mclk, CK_343X), CLK(NULL, "cam_ick", &cam_ick, CK_343X), CLK(NULL, "csi2_96m_fck", &csi2_96m_fck, CK_343X), @@ -300,6 +337,73 @@ static struct omap_clk omap34xx_clks[] = { */ #define SDRC_MPURATE_LOOPS 96 +/** + * omap3430es2_clk_ssi_find_idlest - return CM_IDLEST info for SSI + * @clk: struct clk * being enabled + * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into + * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into + * + * The OMAP3430ES2 SSI target CM_IDLEST bit is at a different shift + * from the CM_{I,F}CLKEN bit. Pass back the correct info via + * @idlest_reg and @idlest_bit. No return value. + */ +static void omap3430es2_clk_ssi_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit) +{ + u32 r; + + r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); + *idlest_reg = (__force void __iomem *)r; + *idlest_bit = OMAP3430ES2_ST_SSI_IDLE_SHIFT; +} + +/** + * omap3430es2_clk_dss_usbhost_find_idlest - CM_IDLEST info for DSS, USBHOST + * @clk: struct clk * being enabled + * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into + * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into + * + * Some OMAP modules on OMAP3 ES2+ chips have both initiator and + * target IDLEST bits. For our purposes, we are concerned with the + * target IDLEST bits, which exist at a different bit position than + * the *CLKEN bit position for these modules (DSS and USBHOST) (The + * default find_idlest code assumes that they are at the same + * position.) No return value. + */ +static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit) +{ + u32 r; + + r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); + *idlest_reg = (__force void __iomem *)r; + /* USBHOST_IDLE has same shift */ + *idlest_bit = OMAP3430ES2_ST_DSS_IDLE_SHIFT; +} + +/** + * omap3430es2_clk_hsotgusb_find_idlest - return CM_IDLEST info for HSOTGUSB + * @clk: struct clk * being enabled + * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into + * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into + * + * The OMAP3430ES2 HSOTGUSB target CM_IDLEST bit is at a different + * shift from the CM_{I,F}CLKEN bit. Pass back the correct info via + * @idlest_reg and @idlest_bit. No return value. + */ +static void omap3430es2_clk_hsotgusb_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit) +{ + u32 r; + + r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); + *idlest_reg = (__force void __iomem *)r; + *idlest_bit = OMAP3430ES2_ST_HSOTGUSB_IDLE_SHIFT; +} + /** * omap3_dpll_recalc - recalculate DPLL rate * @clk: DPLL struct clk diff --git a/arch/arm/mach-omap2/clock34xx.h b/arch/arm/mach-omap2/clock34xx.h index e433aec4efd..57cc2725b92 100644 --- a/arch/arm/mach-omap2/clock34xx.h +++ b/arch/arm/mach-omap2/clock34xx.h @@ -1568,7 +1568,7 @@ static const struct clksel ssi_ssr_clksel[] = { { .parent = NULL } }; -static struct clk ssi_ssr_fck = { +static struct clk ssi_ssr_fck_3430es1 = { .name = "ssi_ssr_fck", .ops = &clkops_omap2_dflt, .init = &omap2_init_clksel_parent, @@ -1581,10 +1581,31 @@ static struct clk ssi_ssr_fck = { .recalc = &omap2_clksel_recalc, }; -static struct clk ssi_sst_fck = { +static struct clk ssi_ssr_fck_3430es2 = { + .name = "ssi_ssr_fck", + .ops = &clkops_omap3430es2_ssi_wait, + .init = &omap2_init_clksel_parent, + .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1), + .enable_bit = OMAP3430_EN_SSI_SHIFT, + .clksel_reg = OMAP_CM_REGADDR(CORE_MOD, CM_CLKSEL), + .clksel_mask = OMAP3430_CLKSEL_SSI_MASK, + .clksel = ssi_ssr_clksel, + .clkdm_name = "core_l4_clkdm", + .recalc = &omap2_clksel_recalc, +}; + +static struct clk ssi_sst_fck_3430es1 = { .name = "ssi_sst_fck", .ops = &clkops_null, - .parent = &ssi_ssr_fck, + .parent = &ssi_ssr_fck_3430es1, + .fixed_div = 2, + .recalc = &omap2_fixed_divisor_recalc, +}; + +static struct clk ssi_sst_fck_3430es2 = { + .name = "ssi_sst_fck", + .ops = &clkops_null, + .parent = &ssi_ssr_fck_3430es2, .fixed_div = 2, .recalc = &omap2_fixed_divisor_recalc, }; @@ -1606,9 +1627,19 @@ static struct clk core_l3_ick = { .recalc = &followparent_recalc, }; -static struct clk hsotgusb_ick = { +static struct clk hsotgusb_ick_3430es1 = { .name = "hsotgusb_ick", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap2_dflt, + .parent = &core_l3_ick, + .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1), + .enable_bit = OMAP3430_EN_HSOTGUSB_SHIFT, + .clkdm_name = "core_l3_clkdm", + .recalc = &followparent_recalc, +}; + +static struct clk hsotgusb_ick_3430es2 = { + .name = "hsotgusb_ick", + .ops = &clkops_omap3430es2_hsotgusb_wait, .parent = &core_l3_ick, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1), .enable_bit = OMAP3430_EN_HSOTGUSB_SHIFT, @@ -1947,7 +1978,7 @@ static struct clk ssi_l4_ick = { .recalc = &followparent_recalc, }; -static struct clk ssi_ick = { +static struct clk ssi_ick_3430es1 = { .name = "ssi_ick", .ops = &clkops_omap2_dflt, .parent = &ssi_l4_ick, @@ -1957,6 +1988,16 @@ static struct clk ssi_ick = { .recalc = &followparent_recalc, }; +static struct clk ssi_ick_3430es2 = { + .name = "ssi_ick", + .ops = &clkops_omap3430es2_ssi_wait, + .parent = &ssi_l4_ick, + .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1), + .enable_bit = OMAP3430_EN_SSI_SHIFT, + .clkdm_name = "core_l4_clkdm", + .recalc = &followparent_recalc, +}; + /* REVISIT: Technically the TRM claims that this is CORE_CLK based, * but l4_ick makes more sense to me */ @@ -2024,7 +2065,7 @@ static struct clk des1_ick = { }; /* DSS */ -static struct clk dss1_alwon_fck = { +static struct clk dss1_alwon_fck_3430es1 = { .name = "dss1_alwon_fck", .ops = &clkops_omap2_dflt, .parent = &dpll4_m4x2_ck, @@ -2034,6 +2075,16 @@ static struct clk dss1_alwon_fck = { .recalc = &followparent_recalc, }; +static struct clk dss1_alwon_fck_3430es2 = { + .name = "dss1_alwon_fck", + .ops = &clkops_omap3430es2_dss_usbhost_wait, + .parent = &dpll4_m4x2_ck, + .enable_reg = OMAP_CM_REGADDR(OMAP3430_DSS_MOD, CM_FCLKEN), + .enable_bit = OMAP3430_EN_DSS1_SHIFT, + .clkdm_name = "dss_clkdm", + .recalc = &followparent_recalc, +}; + static struct clk dss_tv_fck = { .name = "dss_tv_fck", .ops = &clkops_omap2_dflt, @@ -2067,7 +2118,7 @@ static struct clk dss2_alwon_fck = { .recalc = &followparent_recalc, }; -static struct clk dss_ick = { +static struct clk dss_ick_3430es1 = { /* Handles both L3 and L4 clocks */ .name = "dss_ick", .ops = &clkops_omap2_dflt, @@ -2079,6 +2130,18 @@ static struct clk dss_ick = { .recalc = &followparent_recalc, }; +static struct clk dss_ick_3430es2 = { + /* Handles both L3 and L4 clocks */ + .name = "dss_ick", + .ops = &clkops_omap3430es2_dss_usbhost_wait, + .parent = &l4_ick, + .init = &omap2_init_clk_clkdm, + .enable_reg = OMAP_CM_REGADDR(OMAP3430_DSS_MOD, CM_ICLKEN), + .enable_bit = OMAP3430_CM_ICLKEN_DSS_EN_DSS_SHIFT, + .clkdm_name = "dss_clkdm", + .recalc = &followparent_recalc, +}; + /* CAM */ static struct clk cam_mclk = { @@ -2118,7 +2181,7 @@ static struct clk csi2_96m_fck = { static struct clk usbhost_120m_fck = { .name = "usbhost_120m_fck", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap2_dflt, .parent = &dpll5_m2_ck, .init = &omap2_init_clk_clkdm, .enable_reg = OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_FCLKEN), @@ -2129,7 +2192,7 @@ static struct clk usbhost_120m_fck = { static struct clk usbhost_48m_fck = { .name = "usbhost_48m_fck", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap3430es2_dss_usbhost_wait, .parent = &omap_48m_fck, .init = &omap2_init_clk_clkdm, .enable_reg = OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_FCLKEN), @@ -2141,7 +2204,7 @@ static struct clk usbhost_48m_fck = { static struct clk usbhost_ick = { /* Handles both L3 and L4 clocks */ .name = "usbhost_ick", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap3430es2_dss_usbhost_wait, .parent = &l4_ick, .init = &omap2_init_clk_clkdm, .enable_reg = OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_ICLKEN), -- GitLab From 81566a060bb8f989cc369ea28837b05bd4adcedb Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:00:15 +0530 Subject: [PATCH 0323/1342] ARM: includecheck fix: misc.c fix the following 'make includecheck' warning: arch/arm/boot/compressed/misc.c: linux/compiler.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Signed-off-by: Russell King --- arch/arm/boot/compressed/misc.c | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/boot/compressed/misc.c b/arch/arm/boot/compressed/misc.c index 9e6e512f011..17153b54613 100644 --- a/arch/arm/boot/compressed/misc.c +++ b/arch/arm/boot/compressed/misc.c @@ -29,7 +29,6 @@ unsigned int __machine_arch_type; static void putstr(const char *ptr); -#include #include #ifdef CONFIG_DEBUG_ICEDCC -- GitLab From feecaf73bb437cf72a44bd71598c6532d357f78e Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:01:39 +0530 Subject: [PATCH 0324/1342] ARM: includecheck fix: atomic.h fix the following 'make includecheck' warning: arch/arm/include/asm/atomic.h: asm/system.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Signed-off-by: Russell King --- arch/arm/include/asm/atomic.h | 2 -- 1 file changed, 2 deletions(-) diff --git a/arch/arm/include/asm/atomic.h b/arch/arm/include/asm/atomic.h index 9e07fe50702..9ed2377fe8e 100644 --- a/arch/arm/include/asm/atomic.h +++ b/arch/arm/include/asm/atomic.h @@ -159,8 +159,6 @@ static inline void atomic_clear_mask(unsigned long mask, unsigned long *addr) #else /* ARM_ARCH_6 */ -#include - #ifdef CONFIG_SMP #error SMP not supported on pre-ARMv6 CPUs #endif -- GitLab From 44e96d452173ed22a7ba2291c7d566bf4b406f62 Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:03:08 +0530 Subject: [PATCH 0325/1342] ARM: includecheck fix: board-dm355-evm.c fix the following 'make includecheck' warning: arch/arm/mach-davinci/board-dm355-evm.c: mach/common.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Kevin Hilman Signed-off-by: Russell King --- arch/arm/mach-davinci/board-dm355-evm.c | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/mach-davinci/board-dm355-evm.c b/arch/arm/mach-davinci/board-dm355-evm.c index 5ac2f565d86..d6ab64ccd49 100644 --- a/arch/arm/mach-davinci/board-dm355-evm.c +++ b/arch/arm/mach-davinci/board-dm355-evm.c @@ -37,7 +37,6 @@ #include #include #include -#include #define DAVINCI_ASYNC_EMIF_CONTROL_BASE 0x01e10000 #define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE 0x02000000 -- GitLab From 7f25b0ac2dde2de399d6cfe42d9ec7066e665f2f Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:04:33 +0530 Subject: [PATCH 0326/1342] ARM: includecheck fix: board-dm355-leopard.c fix the following 'make includecheck' warning: arch/arm/mach-davinci/board-dm355-leopard.c: mach/common.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Kevin Hilman Signed-off-by: Russell King --- arch/arm/mach-davinci/board-dm355-leopard.c | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/mach-davinci/board-dm355-leopard.c b/arch/arm/mach-davinci/board-dm355-leopard.c index 28c9008df4f..84ad5d161a8 100644 --- a/arch/arm/mach-davinci/board-dm355-leopard.c +++ b/arch/arm/mach-davinci/board-dm355-leopard.c @@ -36,7 +36,6 @@ #include #include #include -#include #define DAVINCI_ASYNC_EMIF_CONTROL_BASE 0x01e10000 #define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE 0x02000000 -- GitLab From 6608168486973a33d24d27b25fc94d4743c1a1e5 Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:05:34 +0530 Subject: [PATCH 0327/1342] ARM: includecheck fix: board-dm644x-evm.c fix the following 'make includecheck' warning: arch/arm/mach-davinci/board-dm644x-evm.c: mach/common.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Kevin Hilman Signed-off-by: Russell King --- arch/arm/mach-davinci/board-dm644x-evm.c | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/mach-davinci/board-dm644x-evm.c b/arch/arm/mach-davinci/board-dm644x-evm.c index d9d40450bdc..56c8cd01de9 100644 --- a/arch/arm/mach-davinci/board-dm644x-evm.c +++ b/arch/arm/mach-davinci/board-dm644x-evm.c @@ -45,7 +45,6 @@ #include #include #include -#include #define DM644X_EVM_PHY_MASK (0x2) #define DM644X_EVM_MDIO_FREQUENCY (2200000) /* PHY bus frequency */ -- GitLab From 78eacf0b0373f524509da261b771f8baa28806b5 Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:06:42 +0530 Subject: [PATCH 0328/1342] ARM: includecheck fix: board-dm646x-evm.c fix the following 'make includecheck' warning: arch/arm/mach-davinci/board-dm646x-evm.c: mach/common.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Kevin Hilman Signed-off-by: Russell King --- arch/arm/mach-davinci/board-dm646x-evm.c | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/mach-davinci/board-dm646x-evm.c b/arch/arm/mach-davinci/board-dm646x-evm.c index e17de635262..8657e72debc 100644 --- a/arch/arm/mach-davinci/board-dm646x-evm.c +++ b/arch/arm/mach-davinci/board-dm646x-evm.c @@ -47,7 +47,6 @@ #include #include #include -#include #define DM646X_EVM_PHY_MASK (0x2) #define DM646X_EVM_MDIO_FREQUENCY (2200000) /* PHY bus frequency */ -- GitLab From 7a33aed825c4d2bafea748384e3331661fc3a180 Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:07:26 +0530 Subject: [PATCH 0329/1342] ARM: includecheck fix: board-sffsdr.c fix the following 'make includecheck' warning: arch/arm/mach-davinci/board-sffsdr.c: mach/common.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Kevin Hilman Acked-by: Philip Balister Signed-off-by: Russell King --- arch/arm/mach-davinci/board-sffsdr.c | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/mach-davinci/board-sffsdr.c b/arch/arm/mach-davinci/board-sffsdr.c index 748a8e48541..7acdfd8ac07 100644 --- a/arch/arm/mach-davinci/board-sffsdr.c +++ b/arch/arm/mach-davinci/board-sffsdr.c @@ -52,7 +52,6 @@ #include #include #include -#include #define SFFSDR_PHY_MASK (0x2) #define SFFSDR_MDIO_FREQUENCY (2200000) /* PHY bus frequency */ -- GitLab From 52cbbd41f7afeceba4be2e4062138781aacd440c Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:10:02 +0530 Subject: [PATCH 0330/1342] ARM: includecheck fix: mach-omap1/mcbsp.c fix the following 'make includecheck' warning: arch/arm/mach-omap1/mcbsp.c: mach/irqs.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Eduardo Valentin Acked-by: Kevin Hilman Signed-off-by: Russell King --- arch/arm/mach-omap1/mcbsp.c | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/mach-omap1/mcbsp.c b/arch/arm/mach-omap1/mcbsp.c index a2d7814896b..505d98cfe50 100644 --- a/arch/arm/mach-omap1/mcbsp.c +++ b/arch/arm/mach-omap1/mcbsp.c @@ -19,7 +19,6 @@ #include #include -#include #include #include #include -- GitLab From efda2b4c8a643290867d9f5816e36f71a5acee7d Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:11:05 +0530 Subject: [PATCH 0331/1342] ARM: includecheck fix: mach-omap2/mcbsp.c fix the following 'make includecheck' warning: arch/arm/mach-omap2/mcbsp.c: mach/irqs.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Eduardo Valentin Acked-by: Kevin Hilman Signed-off-by: Russell King --- arch/arm/mach-omap2/mcbsp.c | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/mach-omap2/mcbsp.c b/arch/arm/mach-omap2/mcbsp.c index a5c0f0435cd..99b6e154631 100644 --- a/arch/arm/mach-omap2/mcbsp.c +++ b/arch/arm/mach-omap2/mcbsp.c @@ -19,7 +19,6 @@ #include #include -#include #include #include #include -- GitLab From 2e6e2c143cdefc2624722659766d1f3c098d79e1 Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:12:07 +0530 Subject: [PATCH 0332/1342] ARM: includecheck fix: plat-s3c64xx/pm.c fix the following 'make includecheck' warning: arch/arm/plat-s3c64xx/pm.c: plat/regs-gpio.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/plat-s3c64xx/pm.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/arch/arm/plat-s3c64xx/pm.c b/arch/arm/plat-s3c64xx/pm.c index 07a6516a4f3..47632fc7eb6 100644 --- a/arch/arm/plat-s3c64xx/pm.c +++ b/arch/arm/plat-s3c64xx/pm.c @@ -117,8 +117,6 @@ void s3c_pm_save_core(void) * this. */ -#include - static void s3c64xx_cpu_suspend(void) { unsigned long tmp; -- GitLab From 40e03b581a8a0b638bc1e9b957ae0536a4a00ad3 Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:13:24 +0530 Subject: [PATCH 0333/1342] ARM: includecheck fix: plat-stmp3xxx/pinmux.c fix the following 'make includecheck' warning: arch/arm/plat-stmp3xxx/pinmux.c: linux/sysdev.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: dmitry pervushin Signed-off-by: Russell King --- arch/arm/plat-stmp3xxx/pinmux.c | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/plat-stmp3xxx/pinmux.c b/arch/arm/plat-stmp3xxx/pinmux.c index d4120038220..6d6b1a468ed 100644 --- a/arch/arm/plat-stmp3xxx/pinmux.c +++ b/arch/arm/plat-stmp3xxx/pinmux.c @@ -22,7 +22,6 @@ #include #include #include -#include #include #include -- GitLab From f83284fe209b1d143244bf462abf1b414eb7b62a Mon Sep 17 00:00:00 2001 From: roel kluin Date: Sat, 25 Jul 2009 07:41:12 +0000 Subject: [PATCH 0334/1342] fealnx: Write outside array bounds phy_idx is checked to be < 4, but np->phys[] is 2 elements long Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/fealnx.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/net/fealnx.c b/drivers/net/fealnx.c index 891be28a7d4..ee51557e942 100644 --- a/drivers/net/fealnx.c +++ b/drivers/net/fealnx.c @@ -584,7 +584,8 @@ static int __devinit fealnx_init_one(struct pci_dev *pdev, if (np->flags == HAS_MII_XCVR) { int phy, phy_idx = 0; - for (phy = 1; phy < 32 && phy_idx < 4; phy++) { + for (phy = 1; phy < 32 && phy_idx < ARRAY_SIZE(np->phys); + phy++) { int mii_status = mdio_read(dev, phy, 1); if (mii_status != 0xffff && mii_status != 0x0000) { -- GitLab From 3b73e79b0dcc86f8bec68a34b7fb812eec953f34 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Sat, 25 Jul 2009 12:01:50 +0000 Subject: [PATCH 0335/1342] at1700: Read buffer overflow loop bound looks to be wrong, for an array of length 8 Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/at1700.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/at1700.c b/drivers/net/at1700.c index 18b566ad4fd..cf30e278f18 100644 --- a/drivers/net/at1700.c +++ b/drivers/net/at1700.c @@ -318,7 +318,7 @@ static int __init at1700_probe1(struct net_device *dev, int ioaddr) pos3 = mca_read_stored_pos( slot, 3 ); pos4 = mca_read_stored_pos( slot, 4 ); - for (l_i = 0; l_i < 0x09; l_i++) + for (l_i = 0; l_i < 8; l_i++) if (( pos3 & 0x07) == at1700_ioaddr_pattern[l_i]) break; ioaddr = at1700_mca_probe_list[l_i]; -- GitLab From c65d3198addb1a2862d4b88bc2a74ac9cbed66f9 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Sat, 25 Jul 2009 12:38:33 +0000 Subject: [PATCH 0336/1342] tokenring: Read buffer overflow io[i] is read before the bounds check on i, order should be reversed Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/tokenring/ibmtr.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/tokenring/ibmtr.c b/drivers/net/tokenring/ibmtr.c index 9d896116cf7..08a6c41c159 100644 --- a/drivers/net/tokenring/ibmtr.c +++ b/drivers/net/tokenring/ibmtr.c @@ -1912,7 +1912,7 @@ static int __init ibmtr_init(void) find_turbo_adapters(io); - for (i = 0; io[i] && (i < IBMTR_MAX_ADAPTERS); i++) { + for (i = 0; i < IBMTR_MAX_ADAPTERS && io[i]; i++) { struct net_device *dev; irq[i] = 0; mem[i] = 0; -- GitLab From d513d018e2236930b6163241bbdce64d2c0de49e Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Sun, 26 Jul 2009 18:53:17 -0700 Subject: [PATCH 0337/1342] eepro: Read buffer overflow io[i] is read before the bounds check on i, order should be reversed Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/eepro.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/eepro.c b/drivers/net/eepro.c index cc2ab6412c7..4f700348534 100644 --- a/drivers/net/eepro.c +++ b/drivers/net/eepro.c @@ -1784,7 +1784,7 @@ int __init init_module(void) printk(KERN_INFO "eepro_init_module: Auto-detecting boards (May God protect us...)\n"); } - for (i = 0; io[i] != -1 && i < MAX_EEPRO; i++) { + for (i = 0; i < MAX_EEPRO && io[i] != -1; i++) { dev = alloc_etherdev(sizeof(struct eepro_local)); if (!dev) break; -- GitLab From dcf777f6ed9799c5ac90ac17a5c369e6b73ca92e Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Sun, 26 Jul 2009 19:11:14 -0700 Subject: [PATCH 0338/1342] NET: ROSE: Don't use static buffer. The use of a static buffer in rose2asc() to return its result is not threadproof and can result in corruption if multiple threads are trying to use one of the procfs files based on rose2asc(). Signed-off-by: Ralf Baechle Signed-off-by: David S. Miller --- include/net/rose.h | 2 +- net/rose/af_rose.c | 18 ++++++++---------- net/rose/rose_route.c | 23 ++++++++++++----------- 3 files changed, 21 insertions(+), 22 deletions(-) diff --git a/include/net/rose.h b/include/net/rose.h index cbd5364b2c8..5ba9f02731e 100644 --- a/include/net/rose.h +++ b/include/net/rose.h @@ -156,7 +156,7 @@ extern int sysctl_rose_maximum_vcs; extern int sysctl_rose_window_size; extern int rosecmp(rose_address *, rose_address *); extern int rosecmpm(rose_address *, rose_address *, unsigned short); -extern const char *rose2asc(const rose_address *); +extern char *rose2asc(char *buf, const rose_address *); extern struct sock *rose_find_socket(unsigned int, struct rose_neigh *); extern void rose_kill_by_neigh(struct rose_neigh *); extern unsigned int rose_new_lci(struct rose_neigh *); diff --git a/net/rose/af_rose.c b/net/rose/af_rose.c index 6bd8e93869e..f0a76f6bca7 100644 --- a/net/rose/af_rose.c +++ b/net/rose/af_rose.c @@ -92,23 +92,21 @@ static void rose_set_lockdep_key(struct net_device *dev) /* * Convert a ROSE address into text. */ -const char *rose2asc(const rose_address *addr) +char *rose2asc(char *buf, const rose_address *addr) { - static char buffer[11]; - if (addr->rose_addr[0] == 0x00 && addr->rose_addr[1] == 0x00 && addr->rose_addr[2] == 0x00 && addr->rose_addr[3] == 0x00 && addr->rose_addr[4] == 0x00) { - strcpy(buffer, "*"); + strcpy(buf, "*"); } else { - sprintf(buffer, "%02X%02X%02X%02X%02X", addr->rose_addr[0] & 0xFF, + sprintf(buf, "%02X%02X%02X%02X%02X", addr->rose_addr[0] & 0xFF, addr->rose_addr[1] & 0xFF, addr->rose_addr[2] & 0xFF, addr->rose_addr[3] & 0xFF, addr->rose_addr[4] & 0xFF); } - return buffer; + return buf; } /* @@ -1437,7 +1435,7 @@ static void rose_info_stop(struct seq_file *seq, void *v) static int rose_info_show(struct seq_file *seq, void *v) { - char buf[11]; + char buf[11], rsbuf[11]; if (v == SEQ_START_TOKEN) seq_puts(seq, @@ -1455,8 +1453,8 @@ static int rose_info_show(struct seq_file *seq, void *v) devname = dev->name; seq_printf(seq, "%-10s %-9s ", - rose2asc(&rose->dest_addr), - ax2asc(buf, &rose->dest_call)); + rose2asc(rsbuf, &rose->dest_addr), + ax2asc(buf, &rose->dest_call)); if (ax25cmp(&rose->source_call, &null_ax25_address) == 0) callsign = "??????-?"; @@ -1465,7 +1463,7 @@ static int rose_info_show(struct seq_file *seq, void *v) seq_printf(seq, "%-10s %-9s %-5s %3.3X %05d %d %d %d %d %3lu %3lu %3lu %3lu %3lu %3lu/%03lu %5d %5d %ld\n", - rose2asc(&rose->source_addr), + rose2asc(rsbuf, &rose->source_addr), callsign, devname, rose->lci & 0x0FFF, diff --git a/net/rose/rose_route.c b/net/rose/rose_route.c index a81066a1010..9478d9b3d97 100644 --- a/net/rose/rose_route.c +++ b/net/rose/rose_route.c @@ -1104,6 +1104,7 @@ static void rose_node_stop(struct seq_file *seq, void *v) static int rose_node_show(struct seq_file *seq, void *v) { + char rsbuf[11]; int i; if (v == SEQ_START_TOKEN) @@ -1112,13 +1113,13 @@ static int rose_node_show(struct seq_file *seq, void *v) const struct rose_node *rose_node = v; /* if (rose_node->loopback) { seq_printf(seq, "%-10s %04d 1 loopback\n", - rose2asc(&rose_node->address), - rose_node->mask); + rose2asc(rsbuf, &rose_node->address), + rose_node->mask); } else { */ seq_printf(seq, "%-10s %04d %d", - rose2asc(&rose_node->address), - rose_node->mask, - rose_node->count); + rose2asc(rsbuf, &rose_node->address), + rose_node->mask, + rose_node->count); for (i = 0; i < rose_node->count; i++) seq_printf(seq, " %05d", @@ -1267,7 +1268,7 @@ static void rose_route_stop(struct seq_file *seq, void *v) static int rose_route_show(struct seq_file *seq, void *v) { - char buf[11]; + char buf[11], rsbuf[11]; if (v == SEQ_START_TOKEN) seq_puts(seq, @@ -1279,7 +1280,7 @@ static int rose_route_show(struct seq_file *seq, void *v) seq_printf(seq, "%3.3X %-10s %-9s %05d ", rose_route->lci1, - rose2asc(&rose_route->src_addr), + rose2asc(rsbuf, &rose_route->src_addr), ax2asc(buf, &rose_route->src_call), rose_route->neigh1->number); else @@ -1289,10 +1290,10 @@ static int rose_route_show(struct seq_file *seq, void *v) if (rose_route->neigh2) seq_printf(seq, "%3.3X %-10s %-9s %05d\n", - rose_route->lci2, - rose2asc(&rose_route->dest_addr), - ax2asc(buf, &rose_route->dest_call), - rose_route->neigh2->number); + rose_route->lci2, + rose2asc(rsbuf, &rose_route->dest_addr), + ax2asc(buf, &rose_route->dest_call), + rose_route->neigh2->number); else seq_puts(seq, "000 * * 00000\n"); -- GitLab From 4a29f396429132dc59f1856ea6cfc860a1955fa1 Mon Sep 17 00:00:00 2001 From: Alessandro Rubini Date: Wed, 22 Jul 2009 12:49:08 +0000 Subject: [PATCH 0339/1342] smc91x.h: add config for Nomadik evaluation kit Signed-off-by: Alessandro Rubini Acked-by: Andrea Gallo Signed-off-by: David S. Miller --- drivers/net/smc91x.h | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/net/smc91x.h b/drivers/net/smc91x.h index f1f773b17fe..57a159fac99 100644 --- a/drivers/net/smc91x.h +++ b/drivers/net/smc91x.h @@ -186,7 +186,8 @@ static inline void SMC_outw(u16 val, void __iomem *ioaddr, int reg) #define SMC_outsb(a, r, p, l) writesb((a) + (r), p, (l)) #define SMC_IRQ_FLAGS (-1) /* from resource */ -#elif defined(CONFIG_MACH_LOGICPD_PXA270) +#elif defined(CONFIG_MACH_LOGICPD_PXA270) \ + || defined(CONFIG_MACH_NOMADIK_8815NHK) #define SMC_CAN_USE_8BIT 0 #define SMC_CAN_USE_16BIT 1 -- GitLab From c587aea951a56d29741a3cef4ea3e142c93b3207 Mon Sep 17 00:00:00 2001 From: Xiaotian Feng Date: Thu, 23 Jul 2009 23:06:32 +0000 Subject: [PATCH 0340/1342] net/bridge: use kobject_put to release kobject in br_add_if error path kobject_init_and_add will alloc memory for kobj->name, so in br_add_if error path, simply use kobject_del will not free memory for kobj->name. Fix by using kobject_put instead, kobject_put will internally calls kobject_del and frees memory for kobj->name. Signed-off-by: Xiaotian Feng Acked-by: Stephen Hemminger Signed-off-by: David S. Miller --- net/bridge/br_if.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/bridge/br_if.c b/net/bridge/br_if.c index 8a96672e2c5..eb404dc3ed6 100644 --- a/net/bridge/br_if.c +++ b/net/bridge/br_if.c @@ -424,7 +424,7 @@ int br_add_if(struct net_bridge *br, struct net_device *dev) err2: br_fdb_delete_by_port(br, p, 1); err1: - kobject_del(&p->kobj); + kobject_put(&p->kobj); err0: dev_set_promiscuity(dev, -1); put_back: -- GitLab From c8a5a658b826508c7c61b57e9a590f7b8760fb51 Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Sun, 26 Jul 2009 20:17:21 -0700 Subject: [PATCH 0341/1342] netxen: reset ring consumer during cleanup Reset consumer of status rings to 0 when cleaning up sw resources. Status rings are not deleted during suspend since they have napi objects. This ensures correct rx processing across suspen-resume. Signed-off-by: Dhananjay Phadke Signed-off-by: David S. Miller --- drivers/net/netxen/netxen_nic_init.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/net/netxen/netxen_nic_init.c b/drivers/net/netxen/netxen_nic_init.c index 5d3343ef3d8..7acf204e38c 100644 --- a/drivers/net/netxen/netxen_nic_init.c +++ b/drivers/net/netxen/netxen_nic_init.c @@ -184,6 +184,13 @@ void netxen_free_sw_resources(struct netxen_adapter *adapter) kfree(recv_ctx->rds_rings); skip_rds: + if (recv_ctx->sds_rings == NULL) + goto skip_sds; + + for(ring = 0; ring < adapter->max_sds_rings; ring++) + recv_ctx->sds_rings[ring].consumer = 0; + +skip_sds: if (adapter->tx_ring == NULL) return; -- GitLab From ca52efd5490f97f396d3c5863ba714624f272033 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?fran=C3=A7ois=20romieu?= Date: Fri, 24 Jul 2009 12:34:19 +0000 Subject: [PATCH 0342/1342] r8169: WakeOnLan fix for the 8168 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit More stuff for http://bugzilla.kernel.org/show_bug.cgi?id=9512 Some 8168 are unable to WoL when receiving is not enabled (plain old 8169 do not seem to care). It is not exactly pretty to leave the receiver enabled but we should now enable DMA late enough for it to be safe. Some late stage boot failure due to pxe and friends may benefit from the delayed enabling of bus-mastering as well. Signed-off-by: Francois Romieu Tested-by: Jaromír Cápík Cc: Edward Hsu --- drivers/net/r8169.c | 13 +++++++++++-- 1 file changed, 11 insertions(+), 2 deletions(-) diff --git a/drivers/net/r8169.c b/drivers/net/r8169.c index 4b53b58d75f..b82780d805f 100644 --- a/drivers/net/r8169.c +++ b/drivers/net/r8169.c @@ -2060,8 +2060,6 @@ rtl8169_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) } } - pci_set_master(pdev); - /* ioremap MMIO region */ ioaddr = ioremap(pci_resource_start(pdev, region), R8169_REGS_SIZE); if (!ioaddr) { @@ -2089,6 +2087,8 @@ rtl8169_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) RTL_W16(IntrStatus, 0xffff); + pci_set_master(pdev); + /* Identify chip attached to board */ rtl8169_get_mac_version(tp, ioaddr); @@ -3874,6 +3874,15 @@ static void rtl_shutdown(struct pci_dev *pdev) spin_unlock_irq(&tp->lock); if (system_state == SYSTEM_POWER_OFF) { + /* WoL fails with some 8168 when the receiver is disabled. */ + if (tp->features & RTL_FEATURE_WOL) { + pci_clear_master(pdev); + + RTL_W8(ChipCmd, CmdRxEnb); + /* PCI commit */ + RTL_R8(ChipCmd); + } + pci_wake_from_d3(pdev, true); pci_set_power_state(pdev, PCI_D3hot); } -- GitLab From 8bae1b2b13beb4cf4c0f119f97640503c2b74b0f Mon Sep 17 00:00:00 2001 From: Don Skidmore Date: Thu, 23 Jul 2009 18:00:39 +0000 Subject: [PATCH 0343/1342] ixgbe: fix for 82599 errata marking UDP checksum errors There is an 82599 errata that UDP frames with a zero checksum are incorrectly marked as checksum invalid by the hardware. This was leading to misleading hw_csum_rx_error counts. This patch adds a test around this counter increase for this condition. Signed-off-by: Don Skidmore Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_main.c | 17 +++++++++++++++-- 1 file changed, 15 insertions(+), 2 deletions(-) diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index 68877599f6d..200454f30f6 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -511,8 +511,11 @@ static void ixgbe_receive_skb(struct ixgbe_q_vector *q_vector, * @skb: skb currently being received and modified **/ static inline void ixgbe_rx_checksum(struct ixgbe_adapter *adapter, - u32 status_err, struct sk_buff *skb) + union ixgbe_adv_rx_desc *rx_desc, + struct sk_buff *skb) { + u32 status_err = le32_to_cpu(rx_desc->wb.upper.status_error); + skb->ip_summed = CHECKSUM_NONE; /* Rx csum disabled */ @@ -530,6 +533,16 @@ static inline void ixgbe_rx_checksum(struct ixgbe_adapter *adapter, return; if (status_err & IXGBE_RXDADV_ERR_TCPE) { + u16 pkt_info = rx_desc->wb.lower.lo_dword.hs_rss.pkt_info; + + /* + * 82599 errata, UDP frames with a 0 checksum can be marked as + * checksum errors. + */ + if ((pkt_info & IXGBE_RXDADV_PKTTYPE_UDP) && + (adapter->hw.mac.type == ixgbe_mac_82599EB)) + return; + adapter->hw_csum_rx_error++; return; } @@ -803,7 +816,7 @@ static bool ixgbe_clean_rx_irq(struct ixgbe_q_vector *q_vector, goto next_desc; } - ixgbe_rx_checksum(adapter, staterr, skb); + ixgbe_rx_checksum(adapter, rx_desc, skb); /* probably a little skewed due to removing CRC */ total_rx_bytes += skb->len; -- GitLab From efffde36d20613d91a5ea9529b03f477077f41ea Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 9 Jul 2009 11:33:39 +0200 Subject: [PATCH 0344/1342] microblaze: Define tlb_flush macro This fix remove bug which we had till now in all Microblaze MMU code. Primary tested on mmap01 LTP test. We forget to flush invalid tlb which were changed - we used them and there were wrong old data which wasn't correct. Signed-off-by: Michal Simek --- arch/microblaze/include/asm/tlb.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/microblaze/include/asm/tlb.h b/arch/microblaze/include/asm/tlb.h index c472d280113..e8abd4a0349 100644 --- a/arch/microblaze/include/asm/tlb.h +++ b/arch/microblaze/include/asm/tlb.h @@ -11,7 +11,7 @@ #ifndef _ASM_MICROBLAZE_TLB_H #define _ASM_MICROBLAZE_TLB_H -#define tlb_flush(tlb) do {} while (0) +#define tlb_flush(tlb) flush_tlb_mm((tlb)->mm) #include -- GitLab From 1170902b343053f50d4caf8ec2aa745fd0ce5c84 Mon Sep 17 00:00:00 2001 From: Huang Weiyi Date: Sat, 11 Jul 2009 09:32:08 +0800 Subject: [PATCH 0345/1342] microblaze: remove duplicated #include Remove duplicated #include('s) in arch/microblaze/include/asm/io.h Signed-off-by: Huang Weiyi Signed-off-by: Michal Simek --- arch/microblaze/include/asm/io.h | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/microblaze/include/asm/io.h b/arch/microblaze/include/asm/io.h index 5c173424d07..7c3ec13b44d 100644 --- a/arch/microblaze/include/asm/io.h +++ b/arch/microblaze/include/asm/io.h @@ -14,7 +14,6 @@ #include #include #include -#include #include /* Get struct page {...} */ -- GitLab From 909964ec89ba466d75d53250d5738d1891cc1a3d Mon Sep 17 00:00:00 2001 From: John Williams Date: Mon, 22 Jun 2009 14:02:09 +1000 Subject: [PATCH 0346/1342] microblaze: Final support for statically linked DTB If r7 is zero at kernel boot, or does not point to a valid DTB, then we fall back to a DTB (assumed to be) linked statically in the kernel, instead of blindly copying bogus cruft into the kernel DTB memory region Signed-off-by: John Williams Signed-off-by: Michal Simek --- arch/microblaze/include/asm/prom.h | 23 +++++++++++++---------- arch/microblaze/kernel/head.S | 15 +++++++++++---- arch/microblaze/kernel/setup.c | 3 ++- 3 files changed, 26 insertions(+), 15 deletions(-) diff --git a/arch/microblaze/include/asm/prom.h b/arch/microblaze/include/asm/prom.h index 20f7b3a926e..37e6f305a68 100644 --- a/arch/microblaze/include/asm/prom.h +++ b/arch/microblaze/include/asm/prom.h @@ -16,6 +16,18 @@ #define _ASM_MICROBLAZE_PROM_H #ifdef __KERNEL__ +/* Definitions used by the flattened device tree */ +#define OF_DT_HEADER 0xd00dfeed /* marker */ +#define OF_DT_BEGIN_NODE 0x1 /* Start of node, full name */ +#define OF_DT_END_NODE 0x2 /* End node */ +#define OF_DT_PROP 0x3 /* Property: name off, size, content */ +#define OF_DT_NOP 0x4 /* nop */ +#define OF_DT_END 0x9 + +#define OF_DT_VERSION 0x10 + +#ifndef __ASSEMBLY__ + #include #include #include @@ -29,16 +41,6 @@ #define of_prop_cmp(s1, s2) strcmp((s1), (s2)) #define of_node_cmp(s1, s2) strcasecmp((s1), (s2)) -/* Definitions used by the flattened device tree */ -#define OF_DT_HEADER 0xd00dfeed /* marker */ -#define OF_DT_BEGIN_NODE 0x1 /* Start of node, full name */ -#define OF_DT_END_NODE 0x2 /* End node */ -#define OF_DT_PROP 0x3 /* Property: name off, size, content */ -#define OF_DT_NOP 0x4 /* nop */ -#define OF_DT_END 0x9 - -#define OF_DT_VERSION 0x10 - /* * This is what gets passed to the kernel by prom_init or kexec * @@ -309,5 +311,6 @@ extern void __iomem *of_iomap(struct device_node *device, int index); */ #include +#endif /* __ASSEMBLY__ */ #endif /* __KERNEL__ */ #endif /* _ASM_MICROBLAZE_PROM_H */ diff --git a/arch/microblaze/kernel/head.S b/arch/microblaze/kernel/head.S index e568d6ec621..815bcaae99c 100644 --- a/arch/microblaze/kernel/head.S +++ b/arch/microblaze/kernel/head.S @@ -31,6 +31,7 @@ #include #include #include +#include /* for OF_DT_HEADER */ #ifdef CONFIG_MMU #include /* COMMAND_LINE_SIZE */ @@ -54,11 +55,16 @@ ENTRY(_start) andi r1, r1, ~2 mts rmsr, r1 -/* save fdt to kernel location */ -/* r7 stores pointer to fdt blob */ - beqi r7, no_fdt_arg +/* r7 may point to an FDT, or there may be one linked in. + if it's in r7, we've got to save it away ASAP. + We ensure r7 points to a valid FDT, just in case the bootloader + is broken or non-existent */ + beqi r7, no_fdt_arg /* NULL pointer? don't copy */ + lw r11, r0, r7 /* Does r7 point to a */ + rsubi r11, r11, OF_DT_HEADER /* valid FDT? */ + bnei r11, no_fdt_arg /* No - get out of here */ or r11, r0, r0 /* incremment */ - ori r4, r0, TOPHYS(_fdt_start) /* save bram context */ + ori r4, r0, TOPHYS(_fdt_start) ori r3, r0, (0x4000 - 4) _copy_fdt: lw r12, r7, r11 /* r12 = r7 + r11 */ @@ -67,6 +73,7 @@ _copy_fdt: bgtid r3, _copy_fdt /* loop for all entries */ addik r3, r3, -4 /* descrement loop */ no_fdt_arg: + add r7, r0, r0 /* Clear r7, just to be sure */ #ifdef CONFIG_MMU diff --git a/arch/microblaze/kernel/setup.c b/arch/microblaze/kernel/setup.c index 8709bea0960..59a383621b2 100644 --- a/arch/microblaze/kernel/setup.c +++ b/arch/microblaze/kernel/setup.c @@ -139,7 +139,8 @@ void __init machine_early_init(const char *cmdline, unsigned int ram, #endif early_printk("Ramdisk addr 0x%08x, FDT 0x%08x\n", ram, fdt); - printk(KERN_NOTICE "Found FDT at 0x%08x\n", fdt); + if(fdt) + printk(KERN_NOTICE "Found FDT at 0x%08x\n", fdt); #ifdef CONFIG_MTD_UCLINUX early_printk("Found romfs @ 0x%08x (0x%08x)\n", -- GitLab From 74510f2a2751ed56b5ab099b2e3b7697b91aa77e Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Mon, 22 Jun 2009 10:28:40 +0200 Subject: [PATCH 0347/1342] microblaze: Add messages about FDT blob Print accurate message about place where FDT blob is. Signed-off-by: Michal Simek --- arch/microblaze/kernel/setup.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) diff --git a/arch/microblaze/kernel/setup.c b/arch/microblaze/kernel/setup.c index 59a383621b2..2a97bf513b6 100644 --- a/arch/microblaze/kernel/setup.c +++ b/arch/microblaze/kernel/setup.c @@ -138,9 +138,12 @@ void __init machine_early_init(const char *cmdline, unsigned int ram, setup_early_printk(NULL); #endif - early_printk("Ramdisk addr 0x%08x, FDT 0x%08x\n", ram, fdt); - if(fdt) - printk(KERN_NOTICE "Found FDT at 0x%08x\n", fdt); + early_printk("Ramdisk addr 0x%08x, ", ram); + if (fdt) + early_printk("FDT at 0x%08x\n", fdt); + else + early_printk("Compiled-in FDT at 0x%08x\n", + (unsigned int)_fdt_start); #ifdef CONFIG_MTD_UCLINUX early_printk("Found romfs @ 0x%08x (0x%08x)\n", -- GitLab From a69cb8c4662dd0a7b01b32a9165b1a1697068f19 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Mon, 22 Jun 2009 10:55:40 +0200 Subject: [PATCH 0348/1342] microblaze: Not to clear r7 after copying DTB to kernel I can't clear r7 because if I do it I lose information where DTB come from. Signed-off-by: Michal Simek --- arch/microblaze/kernel/head.S | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/microblaze/kernel/head.S b/arch/microblaze/kernel/head.S index 815bcaae99c..3c4d4a2803e 100644 --- a/arch/microblaze/kernel/head.S +++ b/arch/microblaze/kernel/head.S @@ -73,7 +73,6 @@ _copy_fdt: bgtid r3, _copy_fdt /* loop for all entries */ addik r3, r3, -4 /* descrement loop */ no_fdt_arg: - add r7, r0, r0 /* Clear r7, just to be sure */ #ifdef CONFIG_MMU -- GitLab From ea3fd1466f81a851452bf7f34ccb9b5058e4793c Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Mon, 22 Jun 2009 12:31:55 +0200 Subject: [PATCH 0349/1342] microblaze: Clear print messages for DTB passing via r7 It is necessary to zeroed r7 when r7 points to bad dtb - this caused that we have correct messages about compiled-in dtb or passing via r7 Signed-off-by: Michal Simek --- arch/microblaze/kernel/head.S | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/microblaze/kernel/head.S b/arch/microblaze/kernel/head.S index 3c4d4a2803e..e41c6ce2a7b 100644 --- a/arch/microblaze/kernel/head.S +++ b/arch/microblaze/kernel/head.S @@ -62,7 +62,10 @@ ENTRY(_start) beqi r7, no_fdt_arg /* NULL pointer? don't copy */ lw r11, r0, r7 /* Does r7 point to a */ rsubi r11, r11, OF_DT_HEADER /* valid FDT? */ + beqi r11, _prepare_copy_fdt + or r7, r0, r0 /* clear R7 when not valid DTB */ bnei r11, no_fdt_arg /* No - get out of here */ +_prepare_copy_fdt: or r11, r0, r0 /* incremment */ ori r4, r0, TOPHYS(_fdt_start) ori r3, r0, (0x4000 - 4) -- GitLab From 7bcb63b21327427b130edeb6e6ad44ee260b3043 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Mon, 13 Jul 2009 16:46:54 +0200 Subject: [PATCH 0350/1342] microblaze: Fix put_user macro for 64bits arguments For 64bits arguments gcc caused that put_user macro works with wrong value because of optimalization. Adding volatile caused that gcc not optimized it. It is possible to use (as Blackfin do) two put_user macros with 32bits arguments but there is one more instruction which is due to duplication zero return value which is called put_user_asm macro. Signed-off-by: Michal Simek --- arch/microblaze/include/asm/uaccess.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/microblaze/include/asm/uaccess.h b/arch/microblaze/include/asm/uaccess.h index 65adad61e7e..5431b4631a7 100644 --- a/arch/microblaze/include/asm/uaccess.h +++ b/arch/microblaze/include/asm/uaccess.h @@ -189,7 +189,7 @@ extern long strnlen_user(const char *src, long count); #define __put_user(x, ptr) \ ({ \ - __typeof__(*(ptr)) __gu_val = x; \ + __typeof__(*(ptr)) volatile __gu_val = (x); \ long __gu_err = 0; \ switch (sizeof(__gu_val)) { \ case 1: \ -- GitLab From f14d6f7c31c73a902a6b567dc719128e74603902 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Wed, 15 Jul 2009 13:39:35 +0200 Subject: [PATCH 0351/1342] microblaze: Add _PAGE_FILE macros to pgtable.h We need to define _PAGE_FILE macro and change pte functions. Microblaze use the same MMU as PowerPC that's why we define _PAGE_FILE in the same style. This change fixed remap_file_pages01 LTP test. Signed-off-by: Michal Simek --- arch/microblaze/include/asm/pgtable.h | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/microblaze/include/asm/pgtable.h b/arch/microblaze/include/asm/pgtable.h index 4c57a586a98..cc3a4dfc3ea 100644 --- a/arch/microblaze/include/asm/pgtable.h +++ b/arch/microblaze/include/asm/pgtable.h @@ -185,6 +185,7 @@ static inline pte_t pte_mkspecial(pte_t pte) { return pte; } /* Definitions for MicroBlaze. */ #define _PAGE_GUARDED 0x001 /* G: page is guarded from prefetch */ +#define _PAGE_FILE 0x001 /* when !present: nonlinear file mapping */ #define _PAGE_PRESENT 0x002 /* software: PTE contains a translation */ #define _PAGE_NO_CACHE 0x004 /* I: caching is inhibited */ #define _PAGE_WRITETHRU 0x008 /* W: caching is write-through */ @@ -320,8 +321,7 @@ static inline int pte_write(pte_t pte) { return pte_val(pte) & _PAGE_RW; } static inline int pte_exec(pte_t pte) { return pte_val(pte) & _PAGE_EXEC; } static inline int pte_dirty(pte_t pte) { return pte_val(pte) & _PAGE_DIRTY; } static inline int pte_young(pte_t pte) { return pte_val(pte) & _PAGE_ACCESSED; } -/* FIXME */ -static inline int pte_file(pte_t pte) { return 0; } +static inline int pte_file(pte_t pte) { return pte_val(pte) & _PAGE_FILE; } static inline void pte_uncache(pte_t pte) { pte_val(pte) |= _PAGE_NO_CACHE; } static inline void pte_cache(pte_t pte) { pte_val(pte) &= ~_PAGE_NO_CACHE; } @@ -488,7 +488,7 @@ static inline pmd_t *pmd_offset(pgd_t *dir, unsigned long address) /* Encode and decode a nonlinear file mapping entry */ #define PTE_FILE_MAX_BITS 29 #define pte_to_pgoff(pte) (pte_val(pte) >> 3) -#define pgoff_to_pte(off) ((pte_t) { ((off) << 3) }) +#define pgoff_to_pte(off) ((pte_t) { ((off) << 3) | _PAGE_FILE }) extern pgd_t swapper_pg_dir[PTRS_PER_PGD]; -- GitLab From f10eca6e107fd223c24393c09c40b916d2b3c427 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 16 Jul 2009 16:00:49 +0200 Subject: [PATCH 0352/1342] microblaze: Fix do_page_fault for no context Calling fixup when we are in kernel mode. This prevent fault for copy_to/from_user. This fault was find thanks to writev01/03/04 LTP tests. Signed-off-by: Michal Simek --- arch/microblaze/mm/fault.c | 13 ++++--------- 1 file changed, 4 insertions(+), 9 deletions(-) diff --git a/arch/microblaze/mm/fault.c b/arch/microblaze/mm/fault.c index 956607a63f4..398c7611735 100644 --- a/arch/microblaze/mm/fault.c +++ b/arch/microblaze/mm/fault.c @@ -122,15 +122,10 @@ void do_page_fault(struct pt_regs *regs, unsigned long address, } #endif /* CONFIG_KGDB */ - if (in_atomic() || mm == NULL) { - /* FIXME */ - if (kernel_mode(regs)) { - printk(KERN_EMERG - "Page fault in kernel mode - Oooou!!! pid %d\n", - current->pid); - _exception(SIGSEGV, regs, code, address); - return; - } + if (in_atomic() || !mm) { + if (kernel_mode(regs)) + goto bad_area_nosemaphore; + /* in_atomic() in user mode is really bad, as is current->mm == NULL. */ printk(KERN_EMERG "Page fault in user mode with " -- GitLab From 94ad8eb854cbc1cf875a318f9b97314ddc6b1560 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Tue, 21 Jul 2009 12:47:04 +0200 Subject: [PATCH 0353/1342] microblaze: Detect new Microblaze 7.20 versions Signed-off-by: Michal Simek --- arch/microblaze/kernel/cpu/cpuinfo.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/microblaze/kernel/cpu/cpuinfo.c b/arch/microblaze/kernel/cpu/cpuinfo.c index a10bea119b9..c411c6757de 100644 --- a/arch/microblaze/kernel/cpu/cpuinfo.c +++ b/arch/microblaze/kernel/cpu/cpuinfo.c @@ -26,6 +26,8 @@ const struct cpu_ver_key cpu_ver_lookup[] = { {"7.10.b", 0x09}, {"7.10.c", 0x0a}, {"7.10.d", 0x0b}, + {"7.20.a", 0x0c}, + {"7.20.b", 0x0d}, /* FIXME There is no keycode defined in MBV for these versions */ {"2.10.a", 0x10}, {"3.00.a", 0x20}, -- GitLab From 3863dbceac7e69642b95f43de1c12c6236fdbe5b Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Tue, 21 Jul 2009 12:48:01 +0200 Subject: [PATCH 0354/1342] microblaze: Support unaligned address for put/get_user macros This patch add support for cases where load/store instruction in put/get_user macro gets unaligned pointer to data and this address is not valid. I prevent all cases which can failed. I had to disable first stage of unaligned handler which is used only for noMMU kernel and the whole work is done when interrupt is enabled. You have enable HW support for detect unaligned access in Microblaze. This patch fixed three LTP tests: getpeername01, getsockname01, socketpair01 Signed-off-by: Michal Simek --- arch/microblaze/kernel/hw_exception_handler.S | 109 ++++++++---------- arch/microblaze/mm/fault.c | 2 +- 2 files changed, 47 insertions(+), 64 deletions(-) diff --git a/arch/microblaze/kernel/hw_exception_handler.S b/arch/microblaze/kernel/hw_exception_handler.S index 9d591cd74fc..3288c973767 100644 --- a/arch/microblaze/kernel/hw_exception_handler.S +++ b/arch/microblaze/kernel/hw_exception_handler.S @@ -74,6 +74,7 @@ #include #include +#include #include /* Helpful Macros */ @@ -428,19 +429,9 @@ handle_unaligned_ex: mfs r17, rbtr; /* ESR[DS] set - return address in BTR */ nop _no_delayslot: -#endif - -#ifdef CONFIG_MMU - /* Check if unaligned address is last on a 4k page */ - andi r5, r4, 0xffc - xori r5, r5, 0xffc - bnei r5, _unaligned_ex2 - _unaligned_ex1: - RESTORE_STATE; -/* Another page must be accessed or physical address not in page table */ - bri unaligned_data_trap - - _unaligned_ex2: + /* jump to high level unaligned handler */ + RESTORE_STATE; + bri unaligned_data_trap #endif andi r6, r3, 0x3E0; /* Mask and extract the register operand */ srl r6, r6; /* r6 >> 5 */ @@ -450,45 +441,6 @@ _no_delayslot: srl r6, r6; /* Store the register operand in a temporary location */ sbi r6, r0, TOPHYS(ex_reg_op); -#ifdef CONFIG_MMU - /* Get physical address */ - /* If we are faulting a kernel address, we have to use the - * kernel page tables. - */ - ori r5, r0, CONFIG_KERNEL_START - cmpu r5, r4, r5 - bgti r5, _unaligned_ex3 - ori r5, r0, swapper_pg_dir - bri _unaligned_ex4 - - /* Get the PGD for the current thread. */ -_unaligned_ex3: /* user thread */ - addi r5 ,CURRENT_TASK, TOPHYS(0); /* get current task address */ - lwi r5, r5, TASK_THREAD + PGDIR -_unaligned_ex4: - tophys(r5,r5) - BSRLI(r6,r4,20) /* Create L1 (pgdir/pmd) address */ - andi r6, r6, 0xffc -/* Assume pgdir aligned on 4K boundary, no need for "andi r5,r5,0xfffff003" */ - or r5, r5, r6 - lwi r6, r5, 0 /* Get L1 entry */ - andi r5, r6, 0xfffff000 /* Extract L2 (pte) base address. */ - beqi r5, _unaligned_ex1 /* Bail if no table */ - - tophys(r5,r5) - BSRLI(r6,r4,10) /* Compute PTE address */ - andi r6, r6, 0xffc - andi r5, r5, 0xfffff003 - or r5, r5, r6 - lwi r5, r5, 0 /* Get Linux PTE */ - - andi r6, r5, _PAGE_PRESENT - beqi r6, _unaligned_ex1 /* Bail if no page */ - - andi r5, r5, 0xfffff000 /* Extract RPN */ - andi r4, r4, 0x00000fff /* Extract offset */ - or r4, r4, r5 /* Create physical address */ -#endif /* CONFIG_MMU */ andi r6, r3, 0x400; /* Extract ESR[S] */ bnei r6, ex_sw; @@ -959,15 +911,15 @@ _unaligned_data_exception: andi r6, r3, 0x800; /* Extract ESR[W] - delay slot */ ex_lw_vm: beqid r6, ex_lhw_vm; - lbui r5, r4, 0; /* Exception address in r4 - delay slot */ +load1: lbui r5, r4, 0; /* Exception address in r4 - delay slot */ /* Load a word, byte-by-byte from destination address and save it in tmp space*/ la r6, r0, ex_tmp_data_loc_0; sbi r5, r6, 0; - lbui r5, r4, 1; +load2: lbui r5, r4, 1; sbi r5, r6, 1; - lbui r5, r4, 2; +load3: lbui r5, r4, 2; sbi r5, r6, 2; - lbui r5, r4, 3; +load4: lbui r5, r4, 3; sbi r5, r6, 3; brid ex_lw_tail_vm; /* Get the destination register value into r3 - delay slot */ @@ -977,7 +929,7 @@ ex_lhw_vm: * save it in tmp space */ la r6, r0, ex_tmp_data_loc_0; sbi r5, r6, 0; - lbui r5, r4, 1; +load5: lbui r5, r4, 1; sbi r5, r6, 1; lhui r3, r6, 0; /* Get the destination register value into r3 */ ex_lw_tail_vm: @@ -996,22 +948,53 @@ ex_sw_tail_vm: swi r3, r5, 0; /* Get the word - delay slot */ /* Store the word, byte-by-byte into destination address */ lbui r3, r5, 0; - sbi r3, r4, 0; +store1: sbi r3, r4, 0; lbui r3, r5, 1; - sbi r3, r4, 1; +store2: sbi r3, r4, 1; lbui r3, r5, 2; - sbi r3, r4, 2; +store3: sbi r3, r4, 2; lbui r3, r5, 3; brid ret_from_exc; - sbi r3, r4, 3; /* Delay slot */ +store4: sbi r3, r4, 3; /* Delay slot */ ex_shw_vm: /* Store the lower half-word, byte-by-byte into destination address */ lbui r3, r5, 2; - sbi r3, r4, 0; +store5: sbi r3, r4, 0; lbui r3, r5, 3; brid ret_from_exc; - sbi r3, r4, 1; /* Delay slot */ +store6: sbi r3, r4, 1; /* Delay slot */ ex_sw_end_vm: /* Exception handling of store word, ends. */ + +/* We have to prevent cases that get/put_user macros get unaligned pointer + * to bad page area. We have to find out which origin instruction caused it + * and called fixup for that origin instruction not instruction in unaligned + * handler */ +ex_unaligned_fixup: + ori r5, r7, 0 /* setup pointer to pt_regs */ + lwi r6, r7, PT_PC; /* faulting address is one instruction above */ + addik r6, r6, -4 /* for finding proper fixup */ + swi r6, r7, PT_PC; /* a save back it to PT_PC */ + addik r7, r0, SIGSEGV + /* call bad_page_fault for finding aligned fixup, fixup address is saved + * in PT_PC which is used as return address from exception */ + la r15, r0, ret_from_exc-8 /* setup return address */ + brid bad_page_fault + nop + +/* We prevent all load/store because it could failed any attempt to access */ +.section __ex_table,"a"; + .word load1,ex_unaligned_fixup; + .word load2,ex_unaligned_fixup; + .word load3,ex_unaligned_fixup; + .word load4,ex_unaligned_fixup; + .word load5,ex_unaligned_fixup; + .word store1,ex_unaligned_fixup; + .word store2,ex_unaligned_fixup; + .word store3,ex_unaligned_fixup; + .word store4,ex_unaligned_fixup; + .word store5,ex_unaligned_fixup; + .word store6,ex_unaligned_fixup; +.previous; .end _unaligned_data_exception #endif /* CONFIG_MMU */ diff --git a/arch/microblaze/mm/fault.c b/arch/microblaze/mm/fault.c index 398c7611735..d9d249a66ff 100644 --- a/arch/microblaze/mm/fault.c +++ b/arch/microblaze/mm/fault.c @@ -69,7 +69,7 @@ static int store_updates_sp(struct pt_regs *regs) * It is called from do_page_fault above and from some of the procedures * in traps.c. */ -static void bad_page_fault(struct pt_regs *regs, unsigned long address, int sig) +void bad_page_fault(struct pt_regs *regs, unsigned long address, int sig) { const struct exception_table_entry *fixup; /* MS: no context */ -- GitLab From bfc0ca0d33e24fca5b89acb378a8a9712ffe22b6 Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Thu, 18 Jun 2009 19:55:35 +0200 Subject: [PATCH 0355/1342] microblaze: remove sys_ipc The ipc system call is now unused in microblaze, as the system call table points directly to the indidual system calls for IPC. Signed-off-by: Arnd Bergmann Signed-off-by: Michal Simek --- arch/microblaze/kernel/sys_microblaze.c | 99 ------------------------- arch/microblaze/kernel/syscall_table.S | 2 +- 2 files changed, 1 insertion(+), 100 deletions(-) diff --git a/arch/microblaze/kernel/sys_microblaze.c b/arch/microblaze/kernel/sys_microblaze.c index e000bce09b2..b96f1682bb2 100644 --- a/arch/microblaze/kernel/sys_microblaze.c +++ b/arch/microblaze/kernel/sys_microblaze.c @@ -33,105 +33,6 @@ #include #include -/* - * sys_ipc() is the de-multiplexer for the SysV IPC calls.. - * - * This is really horribly ugly. This will be remove with new toolchain. - */ -asmlinkage long -sys_ipc(uint call, int first, int second, int third, void *ptr, long fifth) -{ - int version, ret; - - version = call >> 16; /* hack for backward compatibility */ - call &= 0xffff; - - ret = -EINVAL; - switch (call) { - case SEMOP: - ret = sys_semop(first, (struct sembuf *)ptr, second); - break; - case SEMGET: - ret = sys_semget(first, second, third); - break; - case SEMCTL: - { - union semun fourth; - - if (!ptr) - break; - ret = (access_ok(VERIFY_READ, ptr, sizeof(long)) ? 0 : -EFAULT) - || (get_user(fourth.__pad, (void **)ptr)) ; - if (ret) - break; - ret = sys_semctl(first, second, third, fourth); - break; - } - case MSGSND: - ret = sys_msgsnd(first, (struct msgbuf *) ptr, second, third); - break; - case MSGRCV: - switch (version) { - case 0: { - struct ipc_kludge tmp; - - if (!ptr) - break; - ret = (access_ok(VERIFY_READ, ptr, sizeof(tmp)) - ? 0 : -EFAULT) || copy_from_user(&tmp, - (struct ipc_kludge *) ptr, sizeof(tmp)); - if (ret) - break; - ret = sys_msgrcv(first, tmp.msgp, second, tmp.msgtyp, - third); - break; - } - default: - ret = sys_msgrcv(first, (struct msgbuf *) ptr, - second, fifth, third); - break; - } - break; - case MSGGET: - ret = sys_msgget((key_t) first, second); - break; - case MSGCTL: - ret = sys_msgctl(first, second, (struct msqid_ds *) ptr); - break; - case SHMAT: - switch (version) { - default: { - ulong raddr; - ret = access_ok(VERIFY_WRITE, (ulong *) third, - sizeof(ulong)) ? 0 : -EFAULT; - if (ret) - break; - ret = do_shmat(first, (char *) ptr, second, &raddr); - if (ret) - break; - ret = put_user(raddr, (ulong *) third); - break; - } - case 1: /* iBCS2 emulator entry point */ - if (!segment_eq(get_fs(), get_ds())) - break; - ret = do_shmat(first, (char *) ptr, second, - (ulong *) third); - break; - } - break; - case SHMDT: - ret = sys_shmdt((char *)ptr); - break; - case SHMGET: - ret = sys_shmget(first, second, third); - break; - case SHMCTL: - ret = sys_shmctl(first, second, (struct shmid_ds *) ptr); - break; - } - return ret; -} asmlinkage long microblaze_vfork(struct pt_regs *regs) { diff --git a/arch/microblaze/kernel/syscall_table.S b/arch/microblaze/kernel/syscall_table.S index 31b32a6c5f4..216db817beb 100644 --- a/arch/microblaze/kernel/syscall_table.S +++ b/arch/microblaze/kernel/syscall_table.S @@ -121,7 +121,7 @@ ENTRY(sys_call_table) .long sys_wait4 .long sys_swapoff /* 115 */ .long sys_sysinfo - .long sys_ipc + .long sys_ni_syscall /* old sys_ipc */ .long sys_fsync .long sys_ni_syscall /* sys_sigreturn_wrapper */ .long sys_clone /* 120 */ -- GitLab From fadf2e60a6dc7267658fa0c9e3bef13c699c7e1f Mon Sep 17 00:00:00 2001 From: John Williams Date: Thu, 23 Jul 2009 14:56:49 +1000 Subject: [PATCH 0356/1342] microblaze: Get module loading working New reloc type R_MICROBLAZE_32_PCREL_LO requires a null handler (no work to do). Remove legacy hack for broken linker pre gcc-4.1.1, that required us to extract an offset from the code, add it to the addend, then rewrite the instruction. Fixup the invalid reloc type error output. Boot tested with the xilinx_emaclite ethernet driver. Signed-off-by: John Williams Signed-off-by: Michal Simek --- arch/microblaze/kernel/module.c | 15 ++++++++++----- 1 file changed, 10 insertions(+), 5 deletions(-) diff --git a/arch/microblaze/kernel/module.c b/arch/microblaze/kernel/module.c index 51414171326..93a3871ea54 100644 --- a/arch/microblaze/kernel/module.c +++ b/arch/microblaze/kernel/module.c @@ -57,7 +57,6 @@ int apply_relocate_add(Elf32_Shdr *sechdrs, const char *strtab, Elf32_Rela *rela = (void *)sechdrs[relsec].sh_addr; Elf32_Sym *sym; unsigned long int *location; - unsigned long int locoffs; unsigned long int value; #if __GNUC__ < 4 unsigned long int old_value; @@ -113,10 +112,12 @@ int apply_relocate_add(Elf32_Shdr *sechdrs, const char *strtab, break; case R_MICROBLAZE_64_PCREL: - locoffs = (location[0] & 0xFFFF) << 16 | +#if __GNUC__ < 4 + old_value = (location[0] & 0xFFFF) << 16 | (location[1] & 0xFFFF); - value -= (unsigned long int)(location) + 4 + - locoffs; + value -= old_value; +#endif + value -= (unsigned long int)(location) + 4; location[0] = (location[0] & 0xFFFF0000) | (value >> 16); location[1] = (location[1] & 0xFFFF0000) | @@ -125,6 +126,10 @@ int apply_relocate_add(Elf32_Shdr *sechdrs, const char *strtab, value); break; + case R_MICROBLAZE_32_PCREL_LO: + pr_debug("R_MICROBLAZE_32_PCREL_LO\n"); + break; + case R_MICROBLAZE_NONE: pr_debug("R_MICROBLAZE_NONE\n"); break; @@ -133,7 +138,7 @@ int apply_relocate_add(Elf32_Shdr *sechdrs, const char *strtab, printk(KERN_ERR "module %s: " "Unknown relocation: %u\n", module->name, - ELF32_R_TYPE(rela->r_info)); + ELF32_R_TYPE(rela[i].r_info)); return -ENOEXEC; } } -- GitLab From 679711b82f010b854c5d4d88472c7a20fdc2b5fe Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 23 Jul 2009 08:24:47 +0200 Subject: [PATCH 0357/1342] microblaze: Add support for R_MICROBLAZE_64_NONE For example reiserfs use this relocation type. Signed-off-by: Michal Simek --- arch/microblaze/kernel/module.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/microblaze/kernel/module.c b/arch/microblaze/kernel/module.c index 93a3871ea54..5a45b1adfef 100644 --- a/arch/microblaze/kernel/module.c +++ b/arch/microblaze/kernel/module.c @@ -130,6 +130,10 @@ int apply_relocate_add(Elf32_Shdr *sechdrs, const char *strtab, pr_debug("R_MICROBLAZE_32_PCREL_LO\n"); break; + case R_MICROBLAZE_64_NONE: + pr_debug("R_MICROBLAZE_NONE\n"); + break; + case R_MICROBLAZE_NONE: pr_debug("R_MICROBLAZE_NONE\n"); break; -- GitLab From 65d3db0601509946fe0c9d2c7b12a5a62ca42e5e Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Fri, 24 Jul 2009 08:11:23 +0200 Subject: [PATCH 0358/1342] microblaze: Typo fix for cpu param inconsistency Signed-off-by: Michal Simek --- arch/microblaze/kernel/cpu/cpuinfo-pvr-full.c | 2 +- arch/microblaze/kernel/cpu/cpuinfo-static.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/microblaze/kernel/cpu/cpuinfo-pvr-full.c b/arch/microblaze/kernel/cpu/cpuinfo-pvr-full.c index 153f57c57b6..c259786e7fa 100644 --- a/arch/microblaze/kernel/cpu/cpuinfo-pvr-full.c +++ b/arch/microblaze/kernel/cpu/cpuinfo-pvr-full.c @@ -22,7 +22,7 @@ #define CI(c, p) { ci->c = PVR_##p(pvr); } #define err_printk(x) \ - early_printk("ERROR: Microblaze " x " - different for PVR and DTS\n"); + early_printk("ERROR: Microblaze " x "-different for PVR and DTS\n"); void set_cpuinfo_pvr_full(struct cpuinfo *ci, struct device_node *cpu) { diff --git a/arch/microblaze/kernel/cpu/cpuinfo-static.c b/arch/microblaze/kernel/cpu/cpuinfo-static.c index 450ca6bb828..adb448f93d5 100644 --- a/arch/microblaze/kernel/cpu/cpuinfo-static.c +++ b/arch/microblaze/kernel/cpu/cpuinfo-static.c @@ -18,7 +18,7 @@ static const char family_string[] = CONFIG_XILINX_MICROBLAZE0_FAMILY; static const char cpu_ver_string[] = CONFIG_XILINX_MICROBLAZE0_HW_VER; #define err_printk(x) \ - early_printk("ERROR: Microblaze " x "- different for kernel and DTS\n"); + early_printk("ERROR: Microblaze " x "-different for kernel and DTS\n"); void __init set_cpuinfo_static(struct cpuinfo *ci, struct device_node *cpu) { -- GitLab From 950b260ed21fdb6fa5f18485dabb0b03488431fa Mon Sep 17 00:00:00 2001 From: Sam Ravnborg Date: Fri, 24 Jul 2009 09:04:49 +0200 Subject: [PATCH 0359/1342] microblaze: Makefile cleanup Reviewed the Makefile on request by Michal and this is the resulting changes. o Use ':=' for assignmnet so we do not re-evaluate for each use o Use $(shell echo xxx) to remove "" o Replaced CFLAGS_KERNEL with KBUILD_CFLAGS The settings are equally relevant for modules and the linked kernel o Dropped LDFLAGS_BLOB - it is no longer used o Refactored assignmnets to libs-y and core-y o Use MMU for the MMU specific extension. "MMUEXT" was hurting my eyes and I did not wanted it spread to m68k Signed-off-by: Sam Ravnborg Signed-off-by: Michal Simek --- arch/microblaze/Makefile | 35 +++++++++++++++++---------------- arch/microblaze/kernel/Makefile | 2 +- 2 files changed, 19 insertions(+), 18 deletions(-) diff --git a/arch/microblaze/Makefile b/arch/microblaze/Makefile index d0bcf80a113..8439598d465 100644 --- a/arch/microblaze/Makefile +++ b/arch/microblaze/Makefile @@ -6,14 +6,16 @@ endif # What CPU vesion are we building for, and crack it open # as major.minor.rev -CPU_VER=$(subst ",,$(CONFIG_XILINX_MICROBLAZE0_HW_VER) ) -CPU_MAJOR=$(shell echo $(CPU_VER) | cut -d '.' -f 1) -CPU_MINOR=$(shell echo $(CPU_VER) | cut -d '.' -f 2) -CPU_REV=$(shell echo $(CPU_VER) | cut -d '.' -f 3) +CPU_VER := $(shell echo $(CONFIG_XILINX_MICROBLAZE0_HW_VER)) +CPU_MAJOR := $(shell echo $(CPU_VER) | cut -d '.' -f 1) +CPU_MINOR := $(shell echo $(CPU_VER) | cut -d '.' -f 2) +CPU_REV := $(shell echo $(CPU_VER) | cut -d '.' -f 3) export CPU_VER CPU_MAJOR CPU_MINOR CPU_REV # Use cpu-related CONFIG_ vars to set compile options. +# The various CONFIG_XILINX cpu features options are integers 0/1/2... +# rather than bools y/n # Work out HW multipler support. This is icky. # 1. Spartan2 has no HW multiplers. @@ -34,30 +36,29 @@ CPUFLAGS-$(CONFIG_XILINX_MICROBLAZE0_USE_PCMP_INSTR) += -mxl-pattern-compare CPUFLAGS-1 += $(call cc-option,-mcpu=v$(CPU_VER)) -# The various CONFIG_XILINX cpu features options are integers 0/1/2... -# rather than bools y/n - # r31 holds current when in kernel mode -CFLAGS_KERNEL += -ffixed-r31 $(CPUFLAGS-1) $(CPUFLAGS-2) +KBUILD_KERNEL += -ffixed-r31 $(CPUFLAGS-1) $(CPUFLAGS-2) LDFLAGS := LDFLAGS_vmlinux := -LDFLAGS_BLOB := --format binary --oformat elf32-microblaze -LIBGCC := $(shell $(CC) $(CFLAGS_KERNEL) -print-libgcc-file-name) +LIBGCC := $(shell $(CC) $(KBUILD_KERNEL) -print-libgcc-file-name) -head-y := arch/microblaze/kernel/head.o -libs-y += arch/microblaze/lib/ $(LIBGCC) -core-y += arch/microblaze/kernel/ arch/microblaze/mm/ \ - arch/microblaze/platform/ +head-y := arch/microblaze/kernel/head.o +libs-y += arch/microblaze/lib/ +libs-y += $(LIBGCC) +core-y += arch/microblaze/kernel/ +core-y += arch/microblaze/mm/ +core-y += arch/microblaze/platform/ -boot := arch/$(ARCH)/boot +boot := arch/microblaze/boot # defines filename extension depending memory management type ifeq ($(CONFIG_MMU),) -MMUEXT := -nommu +MMU := -nommu endif -export MMUEXT + +export MMU all: linux.bin diff --git a/arch/microblaze/kernel/Makefile b/arch/microblaze/kernel/Makefile index f4a5e19a20e..d487729683d 100644 --- a/arch/microblaze/kernel/Makefile +++ b/arch/microblaze/kernel/Makefile @@ -17,4 +17,4 @@ obj-$(CONFIG_HEART_BEAT) += heartbeat.o obj-$(CONFIG_MODULES) += microblaze_ksyms.o module.o obj-$(CONFIG_MMU) += misc.o -obj-y += entry$(MMUEXT).o +obj-y += entry$(MMU).o -- GitLab From 505d62d073b528859b43bfb463a6ceaf3581469e Mon Sep 17 00:00:00 2001 From: Sebastian Andrzej Siewior Date: Sun, 26 Jul 2009 14:57:54 +0200 Subject: [PATCH 0360/1342] avr32/lib: fix unaligned memcpy() memcpy(p, unaligned, 4..) returns (p + num_of_unaligned_by_copied) instead of p because p is not preserved in the unaligned case. Noticed by Herbert Xu's superior parameter recycling coding technique which let the md4 self-test fail on avr32. Signed-off-by: Sebastian Andrzej Siewior Signed-off-by: Haavard Skinnemoen --- arch/avr32/lib/memcpy.S | 15 ++++++++++++--- 1 file changed, 12 insertions(+), 3 deletions(-) diff --git a/arch/avr32/lib/memcpy.S b/arch/avr32/lib/memcpy.S index 0abb26142b6..93e74b6fcdb 100644 --- a/arch/avr32/lib/memcpy.S +++ b/arch/avr32/lib/memcpy.S @@ -24,8 +24,8 @@ memcpy: brne 1f /* At this point, "from" is word-aligned */ -2: sub r10, 4 - mov r9, r12 +2: mov r9, r12 +5: sub r10, 4 brlt 4f 3: ld.w r8, r11++ @@ -59,4 +59,13 @@ memcpy: st.b r12++, r8 ld.ub r8, r11++ st.b r12++, r8 - rjmp 2b + mov r8, r12 + add pc, pc, r9 + sub r8, 1 + nop + sub r8, 1 + nop + sub r8, 1 + nop + mov r9, r8 + rjmp 5b -- GitLab From 251ab1a37d9ba810593d5fbf2482bc4ba773fab2 Mon Sep 17 00:00:00 2001 From: Sebastian Andrzej Siewior Date: Sun, 26 Jul 2009 14:58:34 +0200 Subject: [PATCH 0361/1342] avr32/lib: fix unaligned memcpy where len < 4 in case of memcpy(p, unaligned, 1..3) we get 1..3 as the return value instead of p Signed-off-by: Sebastian Andrzej Siewior Signed-off-by: Haavard Skinnemoen --- arch/avr32/lib/memcpy.S | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/avr32/lib/memcpy.S b/arch/avr32/lib/memcpy.S index 93e74b6fcdb..c2ca49d705a 100644 --- a/arch/avr32/lib/memcpy.S +++ b/arch/avr32/lib/memcpy.S @@ -49,6 +49,7 @@ memcpy: /* Handle unaligned "from" pointer */ 1: sub r10, 4 + movlt r9, r12 brlt 4b add r10, r9 lsl r9, 2 -- GitLab From 92c548cd35d50df398f442b07021150094578460 Mon Sep 17 00:00:00 2001 From: Ben Nizette Date: Mon, 20 Apr 2009 12:36:53 +1000 Subject: [PATCH 0362/1342] favr32: improve touchscreen response The ezLCD+101 board (to which an favr-32 is fitted) has a long, unshielded, nasty lead between the touch panel and the ads7843 touch controller. In order to get satisfactory response then, we need to employ every noise-reduction trick in the driver's arsenal. After extensive fiddling I've found some good settings: 1) We keep vref on all the time to dramatically reduce settling times (at the cost of a tiny increase in power consumption). 2) Despite 1 the settling time is still non-zero. 500uS is plenty of time for the signals to settle 3) Despite 1 and 2 there's still a little bit of noise around. By setting a pen recheck delay we make the panel feel less touchy and twitchy. Someone with more time and patience myself might be able to tune this numbers further but these settings are now perfectly acceptable for normal use. Tested on ezLCD+101 though should only improve response on other ezLCD+/ favr-32 boards too. Signed-off-by: Ben Nizette Signed-off-by: Haavard Skinnemoen --- arch/avr32/boards/favr-32/setup.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/avr32/boards/favr-32/setup.c b/arch/avr32/boards/favr-32/setup.c index 46c9b0a224c..75f19f47fb2 100644 --- a/arch/avr32/boards/favr-32/setup.c +++ b/arch/avr32/boards/favr-32/setup.c @@ -72,6 +72,10 @@ static struct ads7846_platform_data ads7843_data = { .debounce_max = 20, .debounce_rep = 4, .debounce_tol = 5, + + .keep_vref_on = true, + .settle_delay_usecs = 500, + .penirq_recheck_delay_usecs = 100, }; static struct spi_board_info __initdata spi1_board_info[] = { -- GitLab From 4afcd2dcc6d89da696fc9d469a909adafa9d3636 Mon Sep 17 00:00:00 2001 From: Wan Wei Date: Mon, 27 Jul 2009 14:34:15 +0200 Subject: [PATCH 0363/1342] amd64_edac: read the right F2 maskoffset reg Signed-off-by: Wan Wei Signed-off-by: Borislav Petkov --- drivers/edac/amd64_edac.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/edac/amd64_edac.c b/drivers/edac/amd64_edac.c index 858fe603722..24964c1d0af 100644 --- a/drivers/edac/amd64_edac.c +++ b/drivers/edac/amd64_edac.c @@ -970,7 +970,7 @@ static void amd64_read_dct_base_mask(struct amd64_pvt *pvt) } for (cs = 0; cs < pvt->num_dcsm; cs++) { - reg = K8_DCSB0 + (cs * 4); + reg = K8_DCSM0 + (cs * 4); err = pci_read_config_dword(pvt->dram_f2_ctl, reg, &pvt->dcsm0[cs]); if (unlikely(err)) -- GitLab From c640e1cb45cb9ff6b02f5f130a4f2a58ab9ebe55 Mon Sep 17 00:00:00 2001 From: Tomas Cech Date: Mon, 27 Jul 2009 14:16:31 +0100 Subject: [PATCH 0364/1342] ARM: 5623/1: Treo680: ir shutdown typo fix MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit correct GPIO freed in treo680_irda_shutdown() Signed-off-by: Tomáš ?ech Signed-off-by: Russell King --- arch/arm/mach-pxa/treo680.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-pxa/treo680.c b/arch/arm/mach-pxa/treo680.c index a06f19edebb..753ec4df17b 100644 --- a/arch/arm/mach-pxa/treo680.c +++ b/arch/arm/mach-pxa/treo680.c @@ -409,7 +409,7 @@ err1: static void treo680_irda_shutdown(struct device *dev) { - gpio_free(GPIO_NR_TREO680_AMP_EN); + gpio_free(GPIO_NR_TREO680_IR_EN); } static struct pxaficp_platform_data treo680_ficp_info = { -- GitLab From 0cbb0a781a42f131e9c6836554f402cb85f8f38b Mon Sep 17 00:00:00 2001 From: Deepak Saxena Date: Mon, 27 Jul 2009 10:49:44 -0700 Subject: [PATCH 0365/1342] net: irda: init spinlock after memcpy irttp_dup() copies a tsap_cb struct, but does not initialize the spinlock in the new structure, which confuses lockdep. Signed-off-by: Deepak Saxena Signed-off-by: Ingo Molnar Signed-off-by: Thomas Gleixner Signed-off-by: David S. Miller --- net/irda/irttp.c | 1 + 1 file changed, 1 insertion(+) diff --git a/net/irda/irttp.c b/net/irda/irttp.c index ecf4eb2717c..9cb79f95bf6 100644 --- a/net/irda/irttp.c +++ b/net/irda/irttp.c @@ -1453,6 +1453,7 @@ struct tsap_cb *irttp_dup(struct tsap_cb *orig, void *instance) } /* Dup */ memcpy(new, orig, sizeof(struct tsap_cb)); + spin_lock_init(&new->lock); /* We don't need the old instance any more */ spin_unlock_irqrestore(&irttp->tsaps->hb_spinlock, flags); -- GitLab From 631c07c8d12bcc6ce4a0fbfbd64ea843d78e2b10 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Mon, 27 Jul 2009 13:57:00 -0400 Subject: [PATCH 0366/1342] Btrfs: Correct redundant test in add_inode_ref dir has already been tested. It seems that this test should be on the recently returned value inode. A simplified version of the semantic match that finds this problem is as follows: (http://www.emn.fr/x-info/coccinelle/) Signed-off-by: Julia Lawall Signed-off-by: Chris Mason --- fs/btrfs/tree-log.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/btrfs/tree-log.c b/fs/btrfs/tree-log.c index 19560686261..11d0787c618 100644 --- a/fs/btrfs/tree-log.c +++ b/fs/btrfs/tree-log.c @@ -797,7 +797,7 @@ static noinline int add_inode_ref(struct btrfs_trans_handle *trans, return -ENOENT; inode = read_one_inode(root, key->objectid); - BUG_ON(!dir); + BUG_ON(!inode); ref_ptr = btrfs_item_ptr_offset(eb, slot); ref_end = ref_ptr + btrfs_item_size_nr(eb, slot); -- GitLab From 68b38550ddbea13d296184bf69edff387618b1d3 Mon Sep 17 00:00:00 2001 From: Josef Bacik Date: Mon, 27 Jul 2009 13:57:01 -0400 Subject: [PATCH 0367/1342] Btrfs: change how we unpin extents We are racy with async block caching and unpinning extents. This patch makes things much less complicated by only unpinning the extent if the block group is cached. We check the block_group->cached var under the block_group->lock spin lock. If it is set to BTRFS_CACHE_FINISHED then we update the pinned counters, and unpin the extent and add the free space back. If it is not set to this, we start the caching of the block group so the next time we unpin extents we can unpin the extent. This keeps us from racing with the async caching threads, lets us kill the fs wide async thread counter, and keeps us from having to set DELALLOC bits for every extent we hit if there are caching kthreads going. One thing that needed to be changed was btrfs_free_super_mirror_extents. Now instead of just looking for LOCKED extents, we also look for DIRTY extents, since we could have left some extents pinned in the previous transaction that will never get freed now that we are unmounting, which would cause us to leak memory. So btrfs_free_super_mirror_extents has been changed to btrfs_free_pinned_extents, and it will clear the extents locked for the super mirror, and any remaining pinned extents that may be present. Thank you, Signed-off-by: Josef Bacik Signed-off-by: Chris Mason --- fs/btrfs/ctree.h | 5 +- fs/btrfs/disk-io.c | 3 +- fs/btrfs/extent-tree.c | 149 ++++++++++++----------------------------- fs/btrfs/tree-log.c | 2 +- 4 files changed, 46 insertions(+), 113 deletions(-) diff --git a/fs/btrfs/ctree.h b/fs/btrfs/ctree.h index 42b03c4ee49..17ad92c29cf 100644 --- a/fs/btrfs/ctree.h +++ b/fs/btrfs/ctree.h @@ -845,7 +845,6 @@ struct btrfs_fs_info { atomic_t async_submit_draining; atomic_t nr_async_bios; atomic_t async_delalloc_pages; - atomic_t async_caching_threads; /* * this is used by the balancing code to wait for all the pending @@ -1926,7 +1925,7 @@ int btrfs_run_delayed_refs(struct btrfs_trans_handle *trans, struct btrfs_root *root, unsigned long count); int btrfs_lookup_extent(struct btrfs_root *root, u64 start, u64 len); int btrfs_update_pinned_extents(struct btrfs_root *root, - u64 bytenr, u64 num, int pin, int mark_free); + u64 bytenr, u64 num, int pin); int btrfs_drop_leaf_ref(struct btrfs_trans_handle *trans, struct btrfs_root *root, struct extent_buffer *leaf); int btrfs_cross_ref_exist(struct btrfs_trans_handle *trans, @@ -2011,7 +2010,7 @@ void btrfs_delalloc_reserve_space(struct btrfs_root *root, struct inode *inode, u64 bytes); void btrfs_delalloc_free_space(struct btrfs_root *root, struct inode *inode, u64 bytes); -void btrfs_free_super_mirror_extents(struct btrfs_fs_info *info); +void btrfs_free_pinned_extents(struct btrfs_fs_info *info); /* ctree.c */ int btrfs_bin_search(struct extent_buffer *eb, struct btrfs_key *key, int level, int *slot); diff --git a/fs/btrfs/disk-io.c b/fs/btrfs/disk-io.c index ec2c915f7f4..c658397c747 100644 --- a/fs/btrfs/disk-io.c +++ b/fs/btrfs/disk-io.c @@ -1567,7 +1567,6 @@ struct btrfs_root *open_ctree(struct super_block *sb, atomic_set(&fs_info->async_delalloc_pages, 0); atomic_set(&fs_info->async_submit_draining, 0); atomic_set(&fs_info->nr_async_bios, 0); - atomic_set(&fs_info->async_caching_threads, 0); fs_info->sb = sb; fs_info->max_extent = (u64)-1; fs_info->max_inline = 8192 * 1024; @@ -2339,7 +2338,7 @@ int close_ctree(struct btrfs_root *root) free_extent_buffer(root->fs_info->csum_root->commit_root); btrfs_free_block_groups(root->fs_info); - btrfs_free_super_mirror_extents(root->fs_info); + btrfs_free_pinned_extents(root->fs_info); del_fs_roots(fs_info); diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c index 508df5f7d2e..08188f1615d 100644 --- a/fs/btrfs/extent-tree.c +++ b/fs/btrfs/extent-tree.c @@ -153,18 +153,26 @@ block_group_cache_tree_search(struct btrfs_fs_info *info, u64 bytenr, return ret; } -void btrfs_free_super_mirror_extents(struct btrfs_fs_info *info) +/* + * We always set EXTENT_LOCKED for the super mirror extents so we don't + * overwrite them, so those bits need to be unset. Also, if we are unmounting + * with pinned extents still sitting there because we had a block group caching, + * we need to clear those now, since we are done. + */ +void btrfs_free_pinned_extents(struct btrfs_fs_info *info) { u64 start, end, last = 0; int ret; while (1) { ret = find_first_extent_bit(&info->pinned_extents, last, - &start, &end, EXTENT_LOCKED); + &start, &end, + EXTENT_LOCKED|EXTENT_DIRTY); if (ret) break; - unlock_extent(&info->pinned_extents, start, end, GFP_NOFS); + clear_extent_bits(&info->pinned_extents, start, end, + EXTENT_LOCKED|EXTENT_DIRTY, GFP_NOFS); last = end+1; } } @@ -209,8 +217,7 @@ static u64 add_new_free_space(struct btrfs_block_group_cache *block_group, while (start < end) { ret = find_first_extent_bit(&info->pinned_extents, start, &extent_start, &extent_end, - EXTENT_DIRTY|EXTENT_LOCKED| - EXTENT_DELALLOC); + EXTENT_DIRTY|EXTENT_LOCKED); if (ret) break; @@ -238,67 +245,6 @@ static u64 add_new_free_space(struct btrfs_block_group_cache *block_group, return total_added; } -DEFINE_MUTEX(discard_mutex); - -/* - * if async kthreads are running when we cross transactions, we mark any pinned - * extents with EXTENT_DELALLOC and then let the caching kthreads clean up those - * extents when they are done. Also we run this from btrfs_finish_extent_commit - * in case there were some pinned extents that were missed because we had - * already cached that block group. - */ -static void btrfs_discard_pinned_extents(struct btrfs_fs_info *fs_info, - struct btrfs_block_group_cache *cache) -{ - u64 start, end, last; - int ret; - - if (!cache) - last = 0; - else - last = cache->key.objectid; - - mutex_lock(&discard_mutex); - while (1) { - ret = find_first_extent_bit(&fs_info->pinned_extents, last, - &start, &end, EXTENT_DELALLOC); - if (ret) - break; - - if (cache && start >= cache->key.objectid + cache->key.offset) - break; - - - if (!cache) { - cache = btrfs_lookup_block_group(fs_info, start); - BUG_ON(!cache); - - start = max(start, cache->key.objectid); - end = min(end, cache->key.objectid + cache->key.offset - 1); - - if (block_group_cache_done(cache)) - btrfs_add_free_space(cache, start, - end - start + 1); - cache = NULL; - } else { - start = max(start, cache->key.objectid); - end = min(end, cache->key.objectid + cache->key.offset - 1); - btrfs_add_free_space(cache, start, end - start + 1); - } - - clear_extent_bits(&fs_info->pinned_extents, start, end, - EXTENT_DELALLOC, GFP_NOFS); - last = end + 1; - - if (need_resched()) { - mutex_unlock(&discard_mutex); - cond_resched(); - mutex_lock(&discard_mutex); - } - } - mutex_unlock(&discard_mutex); -} - static int caching_kthread(void *data) { struct btrfs_block_group_cache *block_group = data; @@ -317,7 +263,6 @@ static int caching_kthread(void *data) if (!path) return -ENOMEM; - atomic_inc(&fs_info->async_caching_threads); atomic_inc(&block_group->space_info->caching_threads); last = max_t(u64, block_group->key.objectid, BTRFS_SUPER_INFO_OFFSET); again: @@ -399,13 +344,9 @@ next: err: btrfs_free_path(path); up_read(&fs_info->extent_root->commit_root_sem); - atomic_dec(&fs_info->async_caching_threads); atomic_dec(&block_group->space_info->caching_threads); wake_up(&block_group->caching_q); - if (!ret) - btrfs_discard_pinned_extents(fs_info, block_group); - return 0; } @@ -1867,7 +1808,7 @@ static int run_one_delayed_ref(struct btrfs_trans_handle *trans, BUG_ON(ret); } btrfs_update_pinned_extents(root, node->bytenr, - node->num_bytes, 1, 0); + node->num_bytes, 1); update_reserved_extents(root, node->bytenr, node->num_bytes, 0); } @@ -3100,19 +3041,15 @@ static u64 first_logical_byte(struct btrfs_root *root, u64 search_start) } int btrfs_update_pinned_extents(struct btrfs_root *root, - u64 bytenr, u64 num, int pin, int mark_free) + u64 bytenr, u64 num, int pin) { u64 len; struct btrfs_block_group_cache *cache; struct btrfs_fs_info *fs_info = root->fs_info; - if (pin) { + if (pin) set_extent_dirty(&fs_info->pinned_extents, bytenr, bytenr + num - 1, GFP_NOFS); - } else { - clear_extent_dirty(&fs_info->pinned_extents, - bytenr, bytenr + num - 1, GFP_NOFS); - } while (num > 0) { cache = btrfs_lookup_block_group(fs_info, bytenr); @@ -3128,14 +3065,34 @@ int btrfs_update_pinned_extents(struct btrfs_root *root, spin_unlock(&cache->space_info->lock); fs_info->total_pinned += len; } else { + int unpin = 0; + + /* + * in order to not race with the block group caching, we + * only want to unpin the extent if we are cached. If + * we aren't cached, we want to start async caching this + * block group so we can free the extent the next time + * around. + */ spin_lock(&cache->space_info->lock); spin_lock(&cache->lock); - cache->pinned -= len; - cache->space_info->bytes_pinned -= len; + unpin = (cache->cached == BTRFS_CACHE_FINISHED); + if (likely(unpin)) { + cache->pinned -= len; + cache->space_info->bytes_pinned -= len; + fs_info->total_pinned -= len; + } spin_unlock(&cache->lock); spin_unlock(&cache->space_info->lock); - fs_info->total_pinned -= len; - if (block_group_cache_done(cache) && mark_free) + + if (likely(unpin)) + clear_extent_dirty(&fs_info->pinned_extents, + bytenr, bytenr + len -1, + GFP_NOFS); + else + cache_block_group(cache); + + if (unpin) btrfs_add_free_space(cache, bytenr, len); } btrfs_put_block_group(cache); @@ -3181,27 +3138,15 @@ int btrfs_copy_pinned(struct btrfs_root *root, struct extent_io_tree *copy) u64 last = 0; u64 start; u64 end; - bool caching_kthreads = false; struct extent_io_tree *pinned_extents = &root->fs_info->pinned_extents; int ret; - if (atomic_read(&root->fs_info->async_caching_threads)) - caching_kthreads = true; - while (1) { ret = find_first_extent_bit(pinned_extents, last, &start, &end, EXTENT_DIRTY); if (ret) break; - /* - * we need to make sure that the pinned extents don't go away - * while we are caching block groups - */ - if (unlikely(caching_kthreads)) - set_extent_delalloc(pinned_extents, start, end, - GFP_NOFS); - set_extent_dirty(copy, start, end, GFP_NOFS); last = end + 1; } @@ -3215,12 +3160,6 @@ int btrfs_finish_extent_commit(struct btrfs_trans_handle *trans, u64 start; u64 end; int ret; - int mark_free = 1; - - ret = find_first_extent_bit(&root->fs_info->pinned_extents, 0, - &start, &end, EXTENT_DELALLOC); - if (!ret) - mark_free = 0; while (1) { ret = find_first_extent_bit(unpin, 0, &start, &end, @@ -3231,16 +3170,12 @@ int btrfs_finish_extent_commit(struct btrfs_trans_handle *trans, ret = btrfs_discard_extent(root, start, end + 1 - start); /* unlocks the pinned mutex */ - btrfs_update_pinned_extents(root, start, end + 1 - start, 0, - mark_free); + btrfs_update_pinned_extents(root, start, end + 1 - start, 0); clear_extent_dirty(unpin, start, end, GFP_NOFS); cond_resched(); } - if (unlikely(!mark_free)) - btrfs_discard_pinned_extents(root->fs_info, NULL); - return ret; } @@ -3281,7 +3216,7 @@ static int pin_down_bytes(struct btrfs_trans_handle *trans, pinit: btrfs_set_path_blocking(path); /* unlocks the pinned mutex */ - btrfs_update_pinned_extents(root, bytenr, num_bytes, 1, 0); + btrfs_update_pinned_extents(root, bytenr, num_bytes, 1); BUG_ON(err < 0); return 0; @@ -3592,7 +3527,7 @@ int btrfs_free_extent(struct btrfs_trans_handle *trans, if (root_objectid == BTRFS_TREE_LOG_OBJECTID) { WARN_ON(owner >= BTRFS_FIRST_FREE_OBJECTID); /* unlocks the pinned mutex */ - btrfs_update_pinned_extents(root, bytenr, num_bytes, 1, 0); + btrfs_update_pinned_extents(root, bytenr, num_bytes, 1); update_reserved_extents(root, bytenr, num_bytes, 0); ret = 0; } else if (owner < BTRFS_FIRST_FREE_OBJECTID) { diff --git a/fs/btrfs/tree-log.c b/fs/btrfs/tree-log.c index 11d0787c618..d91b0de7c50 100644 --- a/fs/btrfs/tree-log.c +++ b/fs/btrfs/tree-log.c @@ -264,7 +264,7 @@ static int process_one_buffer(struct btrfs_root *log, { if (wc->pin) btrfs_update_pinned_extents(log->fs_info->extent_root, - eb->start, eb->len, 1, 0); + eb->start, eb->len, 1); if (btrfs_buffer_uptodate(eb, gen)) { if (wc->write) -- GitLab From 6d7760a88c25057c2c2243e5dfe2d731064bd31d Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Mon, 27 Jul 2009 11:25:58 -0700 Subject: [PATCH 0368/1342] cnic: Fix ISCSI_KEVENT_IF_DOWN message handling. When a net device goes down or when the bnx2i driver is unloaded, the code was not generating the ISCSI_KEVENT_IF_DOWN message properly and this could cause the userspace driver to crash. This is fixed by sending the message properly in the shutdown path. cnic_uio_stop() is also added to send the message when bnx2i is unregistering. Signed-off-by: Michael Chan Signed-off-by: David S. Miller --- drivers/net/cnic.c | 23 +++++++++++++++++++++-- 1 file changed, 21 insertions(+), 2 deletions(-) diff --git a/drivers/net/cnic.c b/drivers/net/cnic.c index 4d1515f45ba..4869d77cbe9 100644 --- a/drivers/net/cnic.c +++ b/drivers/net/cnic.c @@ -227,7 +227,7 @@ static int cnic_send_nlmsg(struct cnic_local *cp, u32 type, } rcu_read_lock(); - ulp_ops = rcu_dereference(cp->ulp_ops[CNIC_ULP_ISCSI]); + ulp_ops = rcu_dereference(cnic_ulp_tbl[CNIC_ULP_ISCSI]); if (ulp_ops) ulp_ops->iscsi_nl_send_msg(cp->dev, msg_type, buf, len); rcu_read_unlock(); @@ -319,6 +319,20 @@ static int cnic_abort_prep(struct cnic_sock *csk) return 0; } +static void cnic_uio_stop(void) +{ + struct cnic_dev *dev; + + read_lock(&cnic_dev_lock); + list_for_each_entry(dev, &cnic_dev_list, list) { + struct cnic_local *cp = dev->cnic_priv; + + if (cp->cnic_uinfo) + cnic_send_nlmsg(cp, ISCSI_KEVENT_IF_DOWN, NULL); + } + read_unlock(&cnic_dev_lock); +} + int cnic_register_driver(int ulp_type, struct cnic_ulp_ops *ulp_ops) { struct cnic_dev *dev; @@ -390,6 +404,9 @@ int cnic_unregister_driver(int ulp_type) } read_unlock(&cnic_dev_lock); + if (ulp_type == CNIC_ULP_ISCSI) + cnic_uio_stop(); + rcu_assign_pointer(cnic_ulp_tbl[ulp_type], NULL); mutex_unlock(&cnic_lock); @@ -632,7 +649,6 @@ static void cnic_free_resc(struct cnic_dev *dev) int i = 0; if (cp->cnic_uinfo) { - cnic_send_nlmsg(cp, ISCSI_KEVENT_IF_DOWN, NULL); while (cp->uio_dev != -1 && i < 15) { msleep(100); i++; @@ -1057,6 +1073,9 @@ static void cnic_ulp_stop(struct cnic_dev *dev) struct cnic_local *cp = dev->cnic_priv; int if_type; + if (cp->cnic_uinfo) + cnic_send_nlmsg(cp, ISCSI_KEVENT_IF_DOWN, NULL); + rcu_read_lock(); for (if_type = 0; if_type < MAX_CNIC_ULP_TYPE; if_type++) { struct cnic_ulp_ops *ulp_ops; -- GitLab From 9e1b32caa525cb236e80e9c671e179bcecccc657 Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Wed, 22 Jul 2009 15:44:28 +1000 Subject: [PATCH 0369/1342] mm: Pass virtual address to [__]p{te,ud,md}_free_tlb() mm: Pass virtual address to [__]p{te,ud,md}_free_tlb() Upcoming paches to support the new 64-bit "BookE" powerpc architecture will need to have the virtual address corresponding to PTE page when freeing it, due to the way the HW table walker works. Basically, the TLB can be loaded with "large" pages that cover the whole virtual space (well, sort-of, half of it actually) represented by a PTE page, and which contain an "indirect" bit indicating that this TLB entry RPN points to an array of PTEs from which the TLB can then create direct entries. Thus, in order to invalidate those when PTE pages are deleted, we need the virtual address to pass to tlbilx or tlbivax instructions. The old trick of sticking it somewhere in the PTE page struct page sucks too much, the address is almost readily available in all call sites and almost everybody implemets these as macros, so we may as well add the argument everywhere. I added it to the pmd and pud variants for consistency. Signed-off-by: Benjamin Herrenschmidt Acked-by: David Howells [MN10300 & FRV] Acked-by: Nick Piggin Acked-by: Martin Schwidefsky [s390] Signed-off-by: Linus Torvalds --- arch/alpha/include/asm/tlb.h | 4 ++-- arch/arm/include/asm/tlb.h | 4 ++-- arch/avr32/include/asm/pgalloc.h | 2 +- arch/cris/include/asm/pgalloc.h | 2 +- arch/frv/include/asm/pgalloc.h | 4 ++-- arch/frv/include/asm/pgtable.h | 2 +- arch/ia64/include/asm/pgalloc.h | 6 +++--- arch/ia64/include/asm/tlb.h | 12 ++++++------ arch/m32r/include/asm/pgalloc.h | 4 ++-- arch/m68k/include/asm/motorola_pgalloc.h | 6 ++++-- arch/m68k/include/asm/sun3_pgalloc.h | 4 ++-- arch/microblaze/include/asm/pgalloc.h | 4 ++-- arch/mips/include/asm/pgalloc.h | 6 +++--- arch/mn10300/include/asm/pgalloc.h | 2 +- arch/parisc/include/asm/tlb.h | 4 ++-- arch/powerpc/include/asm/pgalloc-32.h | 2 +- arch/powerpc/include/asm/pgalloc-64.h | 4 ++-- arch/powerpc/include/asm/pgalloc.h | 6 +++--- arch/powerpc/mm/hugetlbpage.c | 4 ++-- arch/s390/include/asm/tlb.h | 9 ++++++--- arch/sh/include/asm/pgalloc.h | 4 ++-- arch/sh/include/asm/tlb.h | 6 +++--- arch/sparc/include/asm/pgalloc_32.h | 8 ++++---- arch/sparc/include/asm/tlb_64.h | 6 +++--- arch/um/include/asm/pgalloc.h | 4 ++-- arch/um/include/asm/tlb.h | 6 +++--- arch/x86/include/asm/pgalloc.h | 25 +++++++++++++++++++++--- arch/x86/mm/pgtable.c | 6 +++--- arch/xtensa/include/asm/tlb.h | 2 +- include/asm-generic/4level-fixup.h | 4 ++-- include/asm-generic/pgtable-nopmd.h | 2 +- include/asm-generic/pgtable-nopud.h | 2 +- include/asm-generic/tlb.h | 12 ++++++------ mm/memory.c | 11 ++++++----- 34 files changed, 107 insertions(+), 82 deletions(-) diff --git a/arch/alpha/include/asm/tlb.h b/arch/alpha/include/asm/tlb.h index c13636575fb..42866759f3f 100644 --- a/arch/alpha/include/asm/tlb.h +++ b/arch/alpha/include/asm/tlb.h @@ -9,7 +9,7 @@ #include -#define __pte_free_tlb(tlb, pte) pte_free((tlb)->mm, pte) -#define __pmd_free_tlb(tlb, pmd) pmd_free((tlb)->mm, pmd) +#define __pte_free_tlb(tlb, pte, address) pte_free((tlb)->mm, pte) +#define __pmd_free_tlb(tlb, pmd, address) pmd_free((tlb)->mm, pmd) #endif diff --git a/arch/arm/include/asm/tlb.h b/arch/arm/include/asm/tlb.h index 321c83e43a1..f41a6f57cd1 100644 --- a/arch/arm/include/asm/tlb.h +++ b/arch/arm/include/asm/tlb.h @@ -102,8 +102,8 @@ tlb_end_vma(struct mmu_gather *tlb, struct vm_area_struct *vma) } #define tlb_remove_page(tlb,page) free_page_and_swap_cache(page) -#define pte_free_tlb(tlb, ptep) pte_free((tlb)->mm, ptep) -#define pmd_free_tlb(tlb, pmdp) pmd_free((tlb)->mm, pmdp) +#define pte_free_tlb(tlb, ptep, addr) pte_free((tlb)->mm, ptep) +#define pmd_free_tlb(tlb, pmdp, addr) pmd_free((tlb)->mm, pmdp) #define tlb_migrate_finish(mm) do { } while (0) diff --git a/arch/avr32/include/asm/pgalloc.h b/arch/avr32/include/asm/pgalloc.h index 64082132394..92ecd8446ef 100644 --- a/arch/avr32/include/asm/pgalloc.h +++ b/arch/avr32/include/asm/pgalloc.h @@ -83,7 +83,7 @@ static inline void pte_free(struct mm_struct *mm, pgtable_t pte) quicklist_free_page(QUICK_PT, NULL, pte); } -#define __pte_free_tlb(tlb,pte) \ +#define __pte_free_tlb(tlb,pte,addr) \ do { \ pgtable_page_dtor(pte); \ tlb_remove_page((tlb), pte); \ diff --git a/arch/cris/include/asm/pgalloc.h b/arch/cris/include/asm/pgalloc.h index a1ba761d057..6da975db112 100644 --- a/arch/cris/include/asm/pgalloc.h +++ b/arch/cris/include/asm/pgalloc.h @@ -47,7 +47,7 @@ static inline void pte_free(struct mm_struct *mm, pgtable_t pte) __free_page(pte); } -#define __pte_free_tlb(tlb,pte) \ +#define __pte_free_tlb(tlb,pte,address) \ do { \ pgtable_page_dtor(pte); \ tlb_remove_page((tlb), pte); \ diff --git a/arch/frv/include/asm/pgalloc.h b/arch/frv/include/asm/pgalloc.h index 971e6addb00..416d19a632f 100644 --- a/arch/frv/include/asm/pgalloc.h +++ b/arch/frv/include/asm/pgalloc.h @@ -49,7 +49,7 @@ static inline void pte_free(struct mm_struct *mm, pgtable_t pte) __free_page(pte); } -#define __pte_free_tlb(tlb,pte) \ +#define __pte_free_tlb(tlb,pte,address) \ do { \ pgtable_page_dtor(pte); \ tlb_remove_page((tlb),(pte)); \ @@ -62,7 +62,7 @@ do { \ */ #define pmd_alloc_one(mm, addr) ({ BUG(); ((pmd_t *) 2); }) #define pmd_free(mm, x) do { } while (0) -#define __pmd_free_tlb(tlb,x) do { } while (0) +#define __pmd_free_tlb(tlb,x,a) do { } while (0) #endif /* CONFIG_MMU */ diff --git a/arch/frv/include/asm/pgtable.h b/arch/frv/include/asm/pgtable.h index 33233011b1c..22c60692b55 100644 --- a/arch/frv/include/asm/pgtable.h +++ b/arch/frv/include/asm/pgtable.h @@ -225,7 +225,7 @@ static inline pud_t *pud_offset(pgd_t *pgd, unsigned long address) */ #define pud_alloc_one(mm, address) NULL #define pud_free(mm, x) do { } while (0) -#define __pud_free_tlb(tlb, x) do { } while (0) +#define __pud_free_tlb(tlb, x, address) do { } while (0) /* * The "pud_xxx()" functions here are trivial for a folded two-level diff --git a/arch/ia64/include/asm/pgalloc.h b/arch/ia64/include/asm/pgalloc.h index b9ac1a6fc21..96a8d927db2 100644 --- a/arch/ia64/include/asm/pgalloc.h +++ b/arch/ia64/include/asm/pgalloc.h @@ -48,7 +48,7 @@ static inline void pud_free(struct mm_struct *mm, pud_t *pud) { quicklist_free(0, NULL, pud); } -#define __pud_free_tlb(tlb, pud) pud_free((tlb)->mm, pud) +#define __pud_free_tlb(tlb, pud, address) pud_free((tlb)->mm, pud) #endif /* CONFIG_PGTABLE_4 */ static inline void @@ -67,7 +67,7 @@ static inline void pmd_free(struct mm_struct *mm, pmd_t *pmd) quicklist_free(0, NULL, pmd); } -#define __pmd_free_tlb(tlb, pmd) pmd_free((tlb)->mm, pmd) +#define __pmd_free_tlb(tlb, pmd, address) pmd_free((tlb)->mm, pmd) static inline void pmd_populate(struct mm_struct *mm, pmd_t * pmd_entry, pgtable_t pte) @@ -117,6 +117,6 @@ static inline void check_pgt_cache(void) quicklist_trim(0, NULL, 25, 16); } -#define __pte_free_tlb(tlb, pte) pte_free((tlb)->mm, pte) +#define __pte_free_tlb(tlb, pte, address) pte_free((tlb)->mm, pte) #endif /* _ASM_IA64_PGALLOC_H */ diff --git a/arch/ia64/include/asm/tlb.h b/arch/ia64/include/asm/tlb.h index 20d8a39680c..85d965cb19a 100644 --- a/arch/ia64/include/asm/tlb.h +++ b/arch/ia64/include/asm/tlb.h @@ -236,22 +236,22 @@ do { \ __tlb_remove_tlb_entry(tlb, ptep, addr); \ } while (0) -#define pte_free_tlb(tlb, ptep) \ +#define pte_free_tlb(tlb, ptep, address) \ do { \ tlb->need_flush = 1; \ - __pte_free_tlb(tlb, ptep); \ + __pte_free_tlb(tlb, ptep, address); \ } while (0) -#define pmd_free_tlb(tlb, ptep) \ +#define pmd_free_tlb(tlb, ptep, address) \ do { \ tlb->need_flush = 1; \ - __pmd_free_tlb(tlb, ptep); \ + __pmd_free_tlb(tlb, ptep, address); \ } while (0) -#define pud_free_tlb(tlb, pudp) \ +#define pud_free_tlb(tlb, pudp, address) \ do { \ tlb->need_flush = 1; \ - __pud_free_tlb(tlb, pudp); \ + __pud_free_tlb(tlb, pudp, address); \ } while (0) #endif /* _ASM_IA64_TLB_H */ diff --git a/arch/m32r/include/asm/pgalloc.h b/arch/m32r/include/asm/pgalloc.h index f11a2b909cd..0fc73619897 100644 --- a/arch/m32r/include/asm/pgalloc.h +++ b/arch/m32r/include/asm/pgalloc.h @@ -58,7 +58,7 @@ static inline void pte_free(struct mm_struct *mm, pgtable_t pte) __free_page(pte); } -#define __pte_free_tlb(tlb, pte) pte_free((tlb)->mm, (pte)) +#define __pte_free_tlb(tlb, pte, addr) pte_free((tlb)->mm, (pte)) /* * allocating and freeing a pmd is trivial: the 1-entry pmd is @@ -68,7 +68,7 @@ static inline void pte_free(struct mm_struct *mm, pgtable_t pte) #define pmd_alloc_one(mm, addr) ({ BUG(); ((pmd_t *)2); }) #define pmd_free(mm, x) do { } while (0) -#define __pmd_free_tlb(tlb, x) do { } while (0) +#define __pmd_free_tlb(tlb, x, addr) do { } while (0) #define pgd_populate(mm, pmd, pte) BUG() #define check_pgt_cache() do { } while (0) diff --git a/arch/m68k/include/asm/motorola_pgalloc.h b/arch/m68k/include/asm/motorola_pgalloc.h index d08bf6261df..15ee4c74a9f 100644 --- a/arch/m68k/include/asm/motorola_pgalloc.h +++ b/arch/m68k/include/asm/motorola_pgalloc.h @@ -54,7 +54,8 @@ static inline void pte_free(struct mm_struct *mm, pgtable_t page) __free_page(page); } -static inline void __pte_free_tlb(struct mmu_gather *tlb, pgtable_t page) +static inline void __pte_free_tlb(struct mmu_gather *tlb, pgtable_t page, + unsigned long address) { pgtable_page_dtor(page); cache_page(kmap(page)); @@ -73,7 +74,8 @@ static inline int pmd_free(struct mm_struct *mm, pmd_t *pmd) return free_pointer_table(pmd); } -static inline int __pmd_free_tlb(struct mmu_gather *tlb, pmd_t *pmd) +static inline int __pmd_free_tlb(struct mmu_gather *tlb, pmd_t *pmd, + unsigned long address) { return free_pointer_table(pmd); } diff --git a/arch/m68k/include/asm/sun3_pgalloc.h b/arch/m68k/include/asm/sun3_pgalloc.h index d4c83f14381..48d80d5a666 100644 --- a/arch/m68k/include/asm/sun3_pgalloc.h +++ b/arch/m68k/include/asm/sun3_pgalloc.h @@ -32,7 +32,7 @@ static inline void pte_free(struct mm_struct *mm, pgtable_t page) __free_page(page); } -#define __pte_free_tlb(tlb,pte) \ +#define __pte_free_tlb(tlb,pte,addr) \ do { \ pgtable_page_dtor(pte); \ tlb_remove_page((tlb), pte); \ @@ -80,7 +80,7 @@ static inline void pmd_populate(struct mm_struct *mm, pmd_t *pmd, pgtable_t page * inside the pgd, so has no extra memory associated with it. */ #define pmd_free(mm, x) do { } while (0) -#define __pmd_free_tlb(tlb, x) do { } while (0) +#define __pmd_free_tlb(tlb, x, addr) do { } while (0) static inline void pgd_free(struct mm_struct *mm, pgd_t *pgd) { diff --git a/arch/microblaze/include/asm/pgalloc.h b/arch/microblaze/include/asm/pgalloc.h index 59a757e46ba..b0131da1387 100644 --- a/arch/microblaze/include/asm/pgalloc.h +++ b/arch/microblaze/include/asm/pgalloc.h @@ -180,7 +180,7 @@ extern inline void pte_free(struct mm_struct *mm, struct page *ptepage) __free_page(ptepage); } -#define __pte_free_tlb(tlb, pte) pte_free((tlb)->mm, (pte)) +#define __pte_free_tlb(tlb, pte, addr) pte_free((tlb)->mm, (pte)) #define pmd_populate(mm, pmd, pte) (pmd_val(*(pmd)) = page_address(pte)) @@ -193,7 +193,7 @@ extern inline void pte_free(struct mm_struct *mm, struct page *ptepage) */ #define pmd_alloc_one(mm, address) ({ BUG(); ((pmd_t *)2); }) /*#define pmd_free(mm, x) do { } while (0)*/ -#define __pmd_free_tlb(tlb, x) do { } while (0) +#define __pmd_free_tlb(tlb, x, addr) do { } while (0) #define pgd_populate(mm, pmd, pte) BUG() extern int do_check_pgt_cache(int, int); diff --git a/arch/mips/include/asm/pgalloc.h b/arch/mips/include/asm/pgalloc.h index 1275831dda2..f705735feef 100644 --- a/arch/mips/include/asm/pgalloc.h +++ b/arch/mips/include/asm/pgalloc.h @@ -98,7 +98,7 @@ static inline void pte_free(struct mm_struct *mm, pgtable_t pte) __free_pages(pte, PTE_ORDER); } -#define __pte_free_tlb(tlb,pte) \ +#define __pte_free_tlb(tlb,pte,address) \ do { \ pgtable_page_dtor(pte); \ tlb_remove_page((tlb), pte); \ @@ -111,7 +111,7 @@ do { \ * inside the pgd, so has no extra memory associated with it. */ #define pmd_free(mm, x) do { } while (0) -#define __pmd_free_tlb(tlb, x) do { } while (0) +#define __pmd_free_tlb(tlb, x, addr) do { } while (0) #endif @@ -132,7 +132,7 @@ static inline void pmd_free(struct mm_struct *mm, pmd_t *pmd) free_pages((unsigned long)pmd, PMD_ORDER); } -#define __pmd_free_tlb(tlb, x) pmd_free((tlb)->mm, x) +#define __pmd_free_tlb(tlb, x, addr) pmd_free((tlb)->mm, x) #endif diff --git a/arch/mn10300/include/asm/pgalloc.h b/arch/mn10300/include/asm/pgalloc.h index ec057e1bd4c..a19f11327cd 100644 --- a/arch/mn10300/include/asm/pgalloc.h +++ b/arch/mn10300/include/asm/pgalloc.h @@ -51,6 +51,6 @@ static inline void pte_free(struct mm_struct *mm, struct page *pte) } -#define __pte_free_tlb(tlb, pte) tlb_remove_page((tlb), (pte)) +#define __pte_free_tlb(tlb, pte, addr) tlb_remove_page((tlb), (pte)) #endif /* _ASM_PGALLOC_H */ diff --git a/arch/parisc/include/asm/tlb.h b/arch/parisc/include/asm/tlb.h index 383b1db310e..07924903989 100644 --- a/arch/parisc/include/asm/tlb.h +++ b/arch/parisc/include/asm/tlb.h @@ -21,7 +21,7 @@ do { if (!(tlb)->fullmm) \ #include -#define __pmd_free_tlb(tlb, pmd) pmd_free((tlb)->mm, pmd) -#define __pte_free_tlb(tlb, pte) pte_free((tlb)->mm, pte) +#define __pmd_free_tlb(tlb, pmd, addr) pmd_free((tlb)->mm, pmd) +#define __pte_free_tlb(tlb, pte, addr) pte_free((tlb)->mm, pte) #endif diff --git a/arch/powerpc/include/asm/pgalloc-32.h b/arch/powerpc/include/asm/pgalloc-32.h index 0815eb40aca..c9500d666a1 100644 --- a/arch/powerpc/include/asm/pgalloc-32.h +++ b/arch/powerpc/include/asm/pgalloc-32.h @@ -16,7 +16,7 @@ extern void pgd_free(struct mm_struct *mm, pgd_t *pgd); */ /* #define pmd_alloc_one(mm,address) ({ BUG(); ((pmd_t *)2); }) */ #define pmd_free(mm, x) do { } while (0) -#define __pmd_free_tlb(tlb,x) do { } while (0) +#define __pmd_free_tlb(tlb,x,a) do { } while (0) /* #define pgd_populate(mm, pmd, pte) BUG() */ #ifndef CONFIG_BOOKE diff --git a/arch/powerpc/include/asm/pgalloc-64.h b/arch/powerpc/include/asm/pgalloc-64.h index afda2bdd860..e6f069c4f71 100644 --- a/arch/powerpc/include/asm/pgalloc-64.h +++ b/arch/powerpc/include/asm/pgalloc-64.h @@ -118,11 +118,11 @@ static inline void pgtable_free(pgtable_free_t pgf) kmem_cache_free(pgtable_cache[cachenum], p); } -#define __pmd_free_tlb(tlb, pmd) \ +#define __pmd_free_tlb(tlb, pmd,addr) \ pgtable_free_tlb(tlb, pgtable_free_cache(pmd, \ PMD_CACHE_NUM, PMD_TABLE_SIZE-1)) #ifndef CONFIG_PPC_64K_PAGES -#define __pud_free_tlb(tlb, pud) \ +#define __pud_free_tlb(tlb, pud, addr) \ pgtable_free_tlb(tlb, pgtable_free_cache(pud, \ PUD_CACHE_NUM, PUD_TABLE_SIZE-1)) #endif /* CONFIG_PPC_64K_PAGES */ diff --git a/arch/powerpc/include/asm/pgalloc.h b/arch/powerpc/include/asm/pgalloc.h index 5d8480265a7..1730e5e298d 100644 --- a/arch/powerpc/include/asm/pgalloc.h +++ b/arch/powerpc/include/asm/pgalloc.h @@ -38,14 +38,14 @@ static inline pgtable_free_t pgtable_free_cache(void *p, int cachenum, extern void pgtable_free_tlb(struct mmu_gather *tlb, pgtable_free_t pgf); #ifdef CONFIG_SMP -#define __pte_free_tlb(tlb,ptepage) \ +#define __pte_free_tlb(tlb,ptepage,address) \ do { \ pgtable_page_dtor(ptepage); \ pgtable_free_tlb(tlb, pgtable_free_cache(page_address(ptepage), \ - PTE_NONCACHE_NUM, PTE_TABLE_SIZE-1)); \ + PTE_NONCACHE_NUM, PTE_TABLE_SIZE-1)); \ } while (0) #else -#define __pte_free_tlb(tlb, pte) pte_free((tlb)->mm, (pte)) +#define __pte_free_tlb(tlb, pte, address) pte_free((tlb)->mm, (pte)) #endif diff --git a/arch/powerpc/mm/hugetlbpage.c b/arch/powerpc/mm/hugetlbpage.c index 9920d6a7cf2..c46ef2ffa3d 100644 --- a/arch/powerpc/mm/hugetlbpage.c +++ b/arch/powerpc/mm/hugetlbpage.c @@ -305,7 +305,7 @@ static void hugetlb_free_pmd_range(struct mmu_gather *tlb, pud_t *pud, pmd = pmd_offset(pud, start); pud_clear(pud); - pmd_free_tlb(tlb, pmd); + pmd_free_tlb(tlb, pmd, start); } static void hugetlb_free_pud_range(struct mmu_gather *tlb, pgd_t *pgd, @@ -348,7 +348,7 @@ static void hugetlb_free_pud_range(struct mmu_gather *tlb, pgd_t *pgd, pud = pud_offset(pgd, start); pgd_clear(pgd); - pud_free_tlb(tlb, pud); + pud_free_tlb(tlb, pud, start); } /* diff --git a/arch/s390/include/asm/tlb.h b/arch/s390/include/asm/tlb.h index 3d8a96d39d9..81150b05368 100644 --- a/arch/s390/include/asm/tlb.h +++ b/arch/s390/include/asm/tlb.h @@ -96,7 +96,8 @@ static inline void tlb_remove_page(struct mmu_gather *tlb, struct page *page) * pte_free_tlb frees a pte table and clears the CRSTE for the * page table from the tlb. */ -static inline void pte_free_tlb(struct mmu_gather *tlb, pgtable_t pte) +static inline void pte_free_tlb(struct mmu_gather *tlb, pgtable_t pte, + unsigned long address) { if (!tlb->fullmm) { tlb->array[tlb->nr_ptes++] = pte; @@ -113,7 +114,8 @@ static inline void pte_free_tlb(struct mmu_gather *tlb, pgtable_t pte) * as the pgd. pmd_free_tlb checks the asce_limit against 2GB * to avoid the double free of the pmd in this case. */ -static inline void pmd_free_tlb(struct mmu_gather *tlb, pmd_t *pmd) +static inline void pmd_free_tlb(struct mmu_gather *tlb, pmd_t *pmd, + unsigned long address) { #ifdef __s390x__ if (tlb->mm->context.asce_limit <= (1UL << 31)) @@ -134,7 +136,8 @@ static inline void pmd_free_tlb(struct mmu_gather *tlb, pmd_t *pmd) * as the pgd. pud_free_tlb checks the asce_limit against 4TB * to avoid the double free of the pud in this case. */ -static inline void pud_free_tlb(struct mmu_gather *tlb, pud_t *pud) +static inline void pud_free_tlb(struct mmu_gather *tlb, pud_t *pud, + unsigned long address) { #ifdef __s390x__ if (tlb->mm->context.asce_limit <= (1UL << 42)) diff --git a/arch/sh/include/asm/pgalloc.h b/arch/sh/include/asm/pgalloc.h index 84dd2db7104..89a482750a5 100644 --- a/arch/sh/include/asm/pgalloc.h +++ b/arch/sh/include/asm/pgalloc.h @@ -73,7 +73,7 @@ static inline void pte_free(struct mm_struct *mm, pgtable_t pte) quicklist_free_page(QUICK_PT, NULL, pte); } -#define __pte_free_tlb(tlb,pte) \ +#define __pte_free_tlb(tlb,pte,addr) \ do { \ pgtable_page_dtor(pte); \ tlb_remove_page((tlb), (pte)); \ @@ -85,7 +85,7 @@ do { \ */ #define pmd_free(mm, x) do { } while (0) -#define __pmd_free_tlb(tlb,x) do { } while (0) +#define __pmd_free_tlb(tlb,x,addr) do { } while (0) static inline void check_pgt_cache(void) { diff --git a/arch/sh/include/asm/tlb.h b/arch/sh/include/asm/tlb.h index 9c16f737074..da8fe7ab872 100644 --- a/arch/sh/include/asm/tlb.h +++ b/arch/sh/include/asm/tlb.h @@ -91,9 +91,9 @@ tlb_end_vma(struct mmu_gather *tlb, struct vm_area_struct *vma) } #define tlb_remove_page(tlb,page) free_page_and_swap_cache(page) -#define pte_free_tlb(tlb, ptep) pte_free((tlb)->mm, ptep) -#define pmd_free_tlb(tlb, pmdp) pmd_free((tlb)->mm, pmdp) -#define pud_free_tlb(tlb, pudp) pud_free((tlb)->mm, pudp) +#define pte_free_tlb(tlb, ptep, addr) pte_free((tlb)->mm, ptep) +#define pmd_free_tlb(tlb, pmdp, addr) pmd_free((tlb)->mm, pmdp) +#define pud_free_tlb(tlb, pudp, addr) pud_free((tlb)->mm, pudp) #define tlb_migrate_finish(mm) do { } while (0) diff --git a/arch/sparc/include/asm/pgalloc_32.h b/arch/sparc/include/asm/pgalloc_32.h index 681582d2696..ca2b34456c4 100644 --- a/arch/sparc/include/asm/pgalloc_32.h +++ b/arch/sparc/include/asm/pgalloc_32.h @@ -44,8 +44,8 @@ BTFIXUPDEF_CALL(pmd_t *, pmd_alloc_one, struct mm_struct *, unsigned long) BTFIXUPDEF_CALL(void, free_pmd_fast, pmd_t *) #define free_pmd_fast(pmd) BTFIXUP_CALL(free_pmd_fast)(pmd) -#define pmd_free(mm, pmd) free_pmd_fast(pmd) -#define __pmd_free_tlb(tlb, pmd) pmd_free((tlb)->mm, pmd) +#define pmd_free(mm, pmd) free_pmd_fast(pmd) +#define __pmd_free_tlb(tlb, pmd, addr) pmd_free((tlb)->mm, pmd) BTFIXUPDEF_CALL(void, pmd_populate, pmd_t *, struct page *) #define pmd_populate(MM, PMD, PTE) BTFIXUP_CALL(pmd_populate)(PMD, PTE) @@ -62,7 +62,7 @@ BTFIXUPDEF_CALL(void, free_pte_fast, pte_t *) #define pte_free_kernel(mm, pte) BTFIXUP_CALL(free_pte_fast)(pte) BTFIXUPDEF_CALL(void, pte_free, pgtable_t ) -#define pte_free(mm, pte) BTFIXUP_CALL(pte_free)(pte) -#define __pte_free_tlb(tlb, pte) pte_free((tlb)->mm, pte) +#define pte_free(mm, pte) BTFIXUP_CALL(pte_free)(pte) +#define __pte_free_tlb(tlb, pte, addr) pte_free((tlb)->mm, pte) #endif /* _SPARC_PGALLOC_H */ diff --git a/arch/sparc/include/asm/tlb_64.h b/arch/sparc/include/asm/tlb_64.h index ee38e731bfa..dca406b9b6f 100644 --- a/arch/sparc/include/asm/tlb_64.h +++ b/arch/sparc/include/asm/tlb_64.h @@ -100,9 +100,9 @@ static inline void tlb_remove_page(struct mmu_gather *mp, struct page *page) } #define tlb_remove_tlb_entry(mp,ptep,addr) do { } while (0) -#define pte_free_tlb(mp, ptepage) pte_free((mp)->mm, ptepage) -#define pmd_free_tlb(mp, pmdp) pmd_free((mp)->mm, pmdp) -#define pud_free_tlb(tlb,pudp) __pud_free_tlb(tlb,pudp) +#define pte_free_tlb(mp, ptepage, addr) pte_free((mp)->mm, ptepage) +#define pmd_free_tlb(mp, pmdp, addr) pmd_free((mp)->mm, pmdp) +#define pud_free_tlb(tlb,pudp, addr) __pud_free_tlb(tlb,pudp,addr) #define tlb_migrate_finish(mm) do { } while (0) #define tlb_start_vma(tlb, vma) do { } while (0) diff --git a/arch/um/include/asm/pgalloc.h b/arch/um/include/asm/pgalloc.h index 718984359f8..32c8ce4e151 100644 --- a/arch/um/include/asm/pgalloc.h +++ b/arch/um/include/asm/pgalloc.h @@ -40,7 +40,7 @@ static inline void pte_free(struct mm_struct *mm, pgtable_t pte) __free_page(pte); } -#define __pte_free_tlb(tlb,pte) \ +#define __pte_free_tlb(tlb,pte, address) \ do { \ pgtable_page_dtor(pte); \ tlb_remove_page((tlb),(pte)); \ @@ -53,7 +53,7 @@ static inline void pmd_free(struct mm_struct *mm, pmd_t *pmd) free_page((unsigned long)pmd); } -#define __pmd_free_tlb(tlb,x) tlb_remove_page((tlb),virt_to_page(x)) +#define __pmd_free_tlb(tlb,x, address) tlb_remove_page((tlb),virt_to_page(x)) #endif #define check_pgt_cache() do { } while (0) diff --git a/arch/um/include/asm/tlb.h b/arch/um/include/asm/tlb.h index 5240fa1c5e0..660caedac9e 100644 --- a/arch/um/include/asm/tlb.h +++ b/arch/um/include/asm/tlb.h @@ -116,11 +116,11 @@ static inline void tlb_remove_page(struct mmu_gather *tlb, struct page *page) __tlb_remove_tlb_entry(tlb, ptep, address); \ } while (0) -#define pte_free_tlb(tlb, ptep) __pte_free_tlb(tlb, ptep) +#define pte_free_tlb(tlb, ptep, addr) __pte_free_tlb(tlb, ptep, addr) -#define pud_free_tlb(tlb, pudp) __pud_free_tlb(tlb, pudp) +#define pud_free_tlb(tlb, pudp, addr) __pud_free_tlb(tlb, pudp, addr) -#define pmd_free_tlb(tlb, pmdp) __pmd_free_tlb(tlb, pmdp) +#define pmd_free_tlb(tlb, pmdp, addr) __pmd_free_tlb(tlb, pmdp, addr) #define tlb_migrate_finish(mm) do {} while (0) diff --git a/arch/x86/include/asm/pgalloc.h b/arch/x86/include/asm/pgalloc.h index dd14c54ac71..0e8c2a0fd92 100644 --- a/arch/x86/include/asm/pgalloc.h +++ b/arch/x86/include/asm/pgalloc.h @@ -46,7 +46,13 @@ static inline void pte_free(struct mm_struct *mm, struct page *pte) __free_page(pte); } -extern void __pte_free_tlb(struct mmu_gather *tlb, struct page *pte); +extern void ___pte_free_tlb(struct mmu_gather *tlb, struct page *pte); + +static inline void __pte_free_tlb(struct mmu_gather *tlb, struct page *pte, + unsigned long address) +{ + ___pte_free_tlb(tlb, pte); +} static inline void pmd_populate_kernel(struct mm_struct *mm, pmd_t *pmd, pte_t *pte) @@ -78,7 +84,13 @@ static inline void pmd_free(struct mm_struct *mm, pmd_t *pmd) free_page((unsigned long)pmd); } -extern void __pmd_free_tlb(struct mmu_gather *tlb, pmd_t *pmd); +extern void ___pmd_free_tlb(struct mmu_gather *tlb, pmd_t *pmd); + +static inline void __pmd_free_tlb(struct mmu_gather *tlb, pmd_t *pmd, + unsigned long adddress) +{ + ___pmd_free_tlb(tlb, pmd); +} #ifdef CONFIG_X86_PAE extern void pud_populate(struct mm_struct *mm, pud_t *pudp, pmd_t *pmd); @@ -108,7 +120,14 @@ static inline void pud_free(struct mm_struct *mm, pud_t *pud) free_page((unsigned long)pud); } -extern void __pud_free_tlb(struct mmu_gather *tlb, pud_t *pud); +extern void ___pud_free_tlb(struct mmu_gather *tlb, pud_t *pud); + +static inline void __pud_free_tlb(struct mmu_gather *tlb, pud_t *pud, + unsigned long address) +{ + ___pud_free_tlb(tlb, pud); +} + #endif /* PAGETABLE_LEVELS > 3 */ #endif /* PAGETABLE_LEVELS > 2 */ diff --git a/arch/x86/mm/pgtable.c b/arch/x86/mm/pgtable.c index 8e43bdd4545..af8f9650058 100644 --- a/arch/x86/mm/pgtable.c +++ b/arch/x86/mm/pgtable.c @@ -25,7 +25,7 @@ pgtable_t pte_alloc_one(struct mm_struct *mm, unsigned long address) return pte; } -void __pte_free_tlb(struct mmu_gather *tlb, struct page *pte) +void ___pte_free_tlb(struct mmu_gather *tlb, struct page *pte) { pgtable_page_dtor(pte); paravirt_release_pte(page_to_pfn(pte)); @@ -33,14 +33,14 @@ void __pte_free_tlb(struct mmu_gather *tlb, struct page *pte) } #if PAGETABLE_LEVELS > 2 -void __pmd_free_tlb(struct mmu_gather *tlb, pmd_t *pmd) +void ___pmd_free_tlb(struct mmu_gather *tlb, pmd_t *pmd) { paravirt_release_pmd(__pa(pmd) >> PAGE_SHIFT); tlb_remove_page(tlb, virt_to_page(pmd)); } #if PAGETABLE_LEVELS > 3 -void __pud_free_tlb(struct mmu_gather *tlb, pud_t *pud) +void ___pud_free_tlb(struct mmu_gather *tlb, pud_t *pud) { paravirt_release_pud(__pa(pud) >> PAGE_SHIFT); tlb_remove_page(tlb, virt_to_page(pud)); diff --git a/arch/xtensa/include/asm/tlb.h b/arch/xtensa/include/asm/tlb.h index 31c220faca0..0d766f9c108 100644 --- a/arch/xtensa/include/asm/tlb.h +++ b/arch/xtensa/include/asm/tlb.h @@ -42,6 +42,6 @@ #include -#define __pte_free_tlb(tlb, pte) pte_free((tlb)->mm, pte) +#define __pte_free_tlb(tlb, pte, address) pte_free((tlb)->mm, pte) #endif /* _XTENSA_TLB_H */ diff --git a/include/asm-generic/4level-fixup.h b/include/asm-generic/4level-fixup.h index 9d40e879f99..77ff547730a 100644 --- a/include/asm-generic/4level-fixup.h +++ b/include/asm-generic/4level-fixup.h @@ -27,9 +27,9 @@ #define pud_page_vaddr(pud) pgd_page_vaddr(pud) #undef pud_free_tlb -#define pud_free_tlb(tlb, x) do { } while (0) +#define pud_free_tlb(tlb, x, addr) do { } while (0) #define pud_free(mm, x) do { } while (0) -#define __pud_free_tlb(tlb, x) do { } while (0) +#define __pud_free_tlb(tlb, x, addr) do { } while (0) #undef pud_addr_end #define pud_addr_end(addr, end) (end) diff --git a/include/asm-generic/pgtable-nopmd.h b/include/asm-generic/pgtable-nopmd.h index a7cdc48e8b7..725612b793c 100644 --- a/include/asm-generic/pgtable-nopmd.h +++ b/include/asm-generic/pgtable-nopmd.h @@ -59,7 +59,7 @@ static inline pmd_t * pmd_offset(pud_t * pud, unsigned long address) static inline void pmd_free(struct mm_struct *mm, pmd_t *pmd) { } -#define __pmd_free_tlb(tlb, x) do { } while (0) +#define __pmd_free_tlb(tlb, x, a) do { } while (0) #undef pmd_addr_end #define pmd_addr_end(addr, end) (end) diff --git a/include/asm-generic/pgtable-nopud.h b/include/asm-generic/pgtable-nopud.h index 87cf449a6df..810431d8351 100644 --- a/include/asm-generic/pgtable-nopud.h +++ b/include/asm-generic/pgtable-nopud.h @@ -52,7 +52,7 @@ static inline pud_t * pud_offset(pgd_t * pgd, unsigned long address) */ #define pud_alloc_one(mm, address) NULL #define pud_free(mm, x) do { } while (0) -#define __pud_free_tlb(tlb, x) do { } while (0) +#define __pud_free_tlb(tlb, x, a) do { } while (0) #undef pud_addr_end #define pud_addr_end(addr, end) (end) diff --git a/include/asm-generic/tlb.h b/include/asm-generic/tlb.h index f490e43a90b..e43f9766259 100644 --- a/include/asm-generic/tlb.h +++ b/include/asm-generic/tlb.h @@ -123,24 +123,24 @@ static inline void tlb_remove_page(struct mmu_gather *tlb, struct page *page) __tlb_remove_tlb_entry(tlb, ptep, address); \ } while (0) -#define pte_free_tlb(tlb, ptep) \ +#define pte_free_tlb(tlb, ptep, address) \ do { \ tlb->need_flush = 1; \ - __pte_free_tlb(tlb, ptep); \ + __pte_free_tlb(tlb, ptep, address); \ } while (0) #ifndef __ARCH_HAS_4LEVEL_HACK -#define pud_free_tlb(tlb, pudp) \ +#define pud_free_tlb(tlb, pudp, address) \ do { \ tlb->need_flush = 1; \ - __pud_free_tlb(tlb, pudp); \ + __pud_free_tlb(tlb, pudp, address); \ } while (0) #endif -#define pmd_free_tlb(tlb, pmdp) \ +#define pmd_free_tlb(tlb, pmdp, address) \ do { \ tlb->need_flush = 1; \ - __pmd_free_tlb(tlb, pmdp); \ + __pmd_free_tlb(tlb, pmdp, address); \ } while (0) #define tlb_migrate_finish(mm) do {} while (0) diff --git a/mm/memory.c b/mm/memory.c index 65216194eb8..aede2ce3aba 100644 --- a/mm/memory.c +++ b/mm/memory.c @@ -135,11 +135,12 @@ void pmd_clear_bad(pmd_t *pmd) * Note: this doesn't free the actual pages themselves. That * has been handled earlier when unmapping all the memory regions. */ -static void free_pte_range(struct mmu_gather *tlb, pmd_t *pmd) +static void free_pte_range(struct mmu_gather *tlb, pmd_t *pmd, + unsigned long addr) { pgtable_t token = pmd_pgtable(*pmd); pmd_clear(pmd); - pte_free_tlb(tlb, token); + pte_free_tlb(tlb, token, addr); tlb->mm->nr_ptes--; } @@ -157,7 +158,7 @@ static inline void free_pmd_range(struct mmu_gather *tlb, pud_t *pud, next = pmd_addr_end(addr, end); if (pmd_none_or_clear_bad(pmd)) continue; - free_pte_range(tlb, pmd); + free_pte_range(tlb, pmd, addr); } while (pmd++, addr = next, addr != end); start &= PUD_MASK; @@ -173,7 +174,7 @@ static inline void free_pmd_range(struct mmu_gather *tlb, pud_t *pud, pmd = pmd_offset(pud, start); pud_clear(pud); - pmd_free_tlb(tlb, pmd); + pmd_free_tlb(tlb, pmd, start); } static inline void free_pud_range(struct mmu_gather *tlb, pgd_t *pgd, @@ -206,7 +207,7 @@ static inline void free_pud_range(struct mmu_gather *tlb, pgd_t *pgd, pud = pud_offset(pgd, start); pgd_clear(pgd); - pud_free_tlb(tlb, pud); + pud_free_tlb(tlb, pud, start); } /* -- GitLab From 6560dc160f3a96b8f1f43e2c6b51aa6eb9898b90 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Thu, 23 Jul 2009 23:42:08 +0930 Subject: [PATCH 0370/1342] module: use MODULE_SYMBOL_PREFIX with module_layout The check_modstruct_version() needs to look up the symbol "module_layout" in the kernel, but it does so literally and not by a C identifier. The trouble is that it does not include a symbol prefix for those ports that need it (like the Blackfin and H8300 port). So make sure we tack on the MODULE_SYMBOL_PREFIX define to the front of it. Signed-off-by: Mike Frysinger Signed-off-by: Rusty Russell Signed-off-by: Linus Torvalds --- kernel/module.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/kernel/module.c b/kernel/module.c index 0a049837008..fd141140355 100644 --- a/kernel/module.c +++ b/kernel/module.c @@ -1068,7 +1068,8 @@ static inline int check_modstruct_version(Elf_Shdr *sechdrs, { const unsigned long *crc; - if (!find_symbol("module_layout", NULL, &crc, true, false)) + if (!find_symbol(MODULE_SYMBOL_PREFIX "module_layout", NULL, + &crc, true, false)) BUG(); return check_version(sechdrs, versindex, "module_layout", mod, crc); } -- GitLab From 9ae260270c90643156cda73427aa1f04c923e627 Mon Sep 17 00:00:00 2001 From: Oleg Nesterov Date: Fri, 19 Jun 2009 02:51:13 +0200 Subject: [PATCH 0371/1342] update the comment in kthread_stop() Commit 63706172f332fd3f6e7458ebfb35fa6de9c21dc5 ("kthreads: rework kthread_stop()") removed the limitation that the thread function mysr not call do_exit() itself, but forgot to update the comment. Since that commit it is OK to use kthread_stop() even if kthread can exit itself. Signed-off-by: Oleg Nesterov Signed-off-by: Rusty Russell Signed-off-by: Linus Torvalds --- kernel/kthread.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-) diff --git a/kernel/kthread.c b/kernel/kthread.c index 9b1a7de2697..eb8751aa041 100644 --- a/kernel/kthread.c +++ b/kernel/kthread.c @@ -180,10 +180,12 @@ EXPORT_SYMBOL(kthread_bind); * @k: thread created by kthread_create(). * * Sets kthread_should_stop() for @k to return true, wakes it, and - * waits for it to exit. Your threadfn() must not call do_exit() - * itself if you use this function! This can also be called after - * kthread_create() instead of calling wake_up_process(): the thread - * will exit without calling threadfn(). + * waits for it to exit. This can also be called after kthread_create() + * instead of calling wake_up_process(): the thread will exit without + * calling threadfn(). + * + * If threadfn() may call do_exit() itself, the caller must ensure + * task_struct can't go away. * * Returns the result of threadfn(), or %-EINTR if wake_up_process() * was never called. -- GitLab From 3995bd9332a51b626237d6671cfeb7235e6c1305 Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Fri, 24 Jul 2009 11:13:14 -0700 Subject: [PATCH 0372/1342] iwlwifi: fix TX queue race I had a problem on 4965 hardware (well, probably other hardware too, but others don't survive my stress testing right now, unfortunately) where the driver was sending invalid commands to the device, but no such thing could be seen from the driver's point of view. I could reproduce this fairly easily by sending multiple TCP streams with iperf on different TIDs, though sometimes a single iperf stream was sufficient. It even happened with a single core, but I have forced preemption turned on. The culprit was a queue overrun, where we advanced the queue's write pointer over the read pointer. After careful analysis I've come to the conclusion that the cause is a race condition between iwlwifi and mac80211. mac80211, of course, checks whether the queue is stopped, before transmitting a frame. This effectively looks like this: lock(queues) if (stopped(queue)) { unlock(queues) return busy; } unlock(queues) ... <-- this place will be important there is some more code here drv_tx(frame) The driver, on the other hand, can stop and start queues, which does lock(queues) mark_running/stopped(queue) unlock(queues) [if marked running: wake up tasklet to send pending frames] Now, however, once the driver starts the queue, mac80211 can see that and end up at the marked place above, at which point for some reason the driver seems to stop the queue again (I don't understand that) and then we end up transmitting while the queue is actually full. Now, this shouldn't actually matter much, but for some reason I've seen it happen multiple times in a row and the queue actually overflows, at which point the queue bites itself in the tail and things go completely wrong. This patch fixes this by just dropping the packet should this have happened, and making the lock in iwlwifi cover everything so iwlwifi can't race against itself (dropping the lock there might make it more likely, but it did seem to happen without that too). Since we can't hold the lock across drv_tx() above, I see no way to fix this in mac80211, but I also don't understand why I haven't seen this before -- maybe I just never stress tested it this badly. With this patch, the device has survived many minutes of simultanously sending two iperf streams on different TIDs with combined throughput of about 60 Mbps. Signed-off-by: Johannes Berg Signed-off-by: Reinette Chatre Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-tx.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/drivers/net/wireless/iwlwifi/iwl-tx.c b/drivers/net/wireless/iwlwifi/iwl-tx.c index 9bbeec9427f..5febb318636 100644 --- a/drivers/net/wireless/iwlwifi/iwl-tx.c +++ b/drivers/net/wireless/iwlwifi/iwl-tx.c @@ -720,8 +720,6 @@ int iwl_tx_skb(struct iwl_priv *priv, struct sk_buff *skb) goto drop_unlock; } - spin_unlock_irqrestore(&priv->lock, flags); - hdr_len = ieee80211_hdrlen(fc); /* Find (or create) index into station table for destination station */ @@ -729,7 +727,7 @@ int iwl_tx_skb(struct iwl_priv *priv, struct sk_buff *skb) if (sta_id == IWL_INVALID_STATION) { IWL_DEBUG_DROP(priv, "Dropping - INVALID STATION: %pM\n", hdr->addr1); - goto drop; + goto drop_unlock; } IWL_DEBUG_TX(priv, "station Id %d\n", sta_id); @@ -750,14 +748,17 @@ int iwl_tx_skb(struct iwl_priv *priv, struct sk_buff *skb) txq_id = priv->stations[sta_id].tid[tid].agg.txq_id; swq_id = iwl_virtual_agg_queue_num(swq_id, txq_id); } - priv->stations[sta_id].tid[tid].tfds_in_queue++; } txq = &priv->txq[txq_id]; q = &txq->q; txq->swq_id = swq_id; - spin_lock_irqsave(&priv->lock, flags); + if (unlikely(iwl_queue_space(q) < q->high_mark)) + goto drop_unlock; + + if (ieee80211_is_data_qos(fc)) + priv->stations[sta_id].tid[tid].tfds_in_queue++; /* Set up driver data for this TFD */ memset(&(txq->txb[q->write_ptr]), 0, sizeof(struct iwl_tx_info)); @@ -902,7 +903,6 @@ int iwl_tx_skb(struct iwl_priv *priv, struct sk_buff *skb) drop_unlock: spin_unlock_irqrestore(&priv->lock, flags); -drop: return -1; } EXPORT_SYMBOL(iwl_tx_skb); -- GitLab From 45f5fa32b130b2a59f9b726be45ce7fa73fb834c Mon Sep 17 00:00:00 2001 From: reinette chatre Date: Tue, 21 Jul 2009 09:29:07 -0700 Subject: [PATCH 0373/1342] iwlagn: fix minimum number of queues setting We need to provide a reasonable minimum that will result in a working setup if used. Set minimum to be 10 to provide for 4 standard TX queues + 1 command queue + 2 (unused) HCCA queues + 4 HT queues (one per AC). We allow the user to change the number of queues used via a module parameter and use this minimum value to check if it is valid. Without this patch a user can select a value for the number of queues that will result in a failing setup. Signed-off-by: Reinette Chatre Reviewed-by: Tomas Winkler Acked-by: Tomas Winkler Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-3945.h | 2 +- drivers/net/wireless/iwlwifi/iwl-dev.h | 6 ++++-- drivers/net/wireless/iwlwifi/iwl3945-base.c | 4 ++-- 3 files changed, 7 insertions(+), 5 deletions(-) diff --git a/drivers/net/wireless/iwlwifi/iwl-3945.h b/drivers/net/wireless/iwlwifi/iwl-3945.h index fbb3a573463..2de6471d4be 100644 --- a/drivers/net/wireless/iwlwifi/iwl-3945.h +++ b/drivers/net/wireless/iwlwifi/iwl-3945.h @@ -112,7 +112,7 @@ enum iwl3945_antenna { #define IWL_TX_FIFO_NONE 7 /* Minimum number of queues. MAX_NUM is defined in hw specific files */ -#define IWL_MIN_NUM_QUEUES 4 +#define IWL39_MIN_NUM_QUEUES 4 #define IEEE80211_DATA_LEN 2304 #define IEEE80211_4ADDR_LEN 30 diff --git a/drivers/net/wireless/iwlwifi/iwl-dev.h b/drivers/net/wireless/iwlwifi/iwl-dev.h index e2d620f0b6e..650e20af20f 100644 --- a/drivers/net/wireless/iwlwifi/iwl-dev.h +++ b/drivers/net/wireless/iwlwifi/iwl-dev.h @@ -258,8 +258,10 @@ struct iwl_channel_info { #define IWL_TX_FIFO_HCCA_2 6 #define IWL_TX_FIFO_NONE 7 -/* Minimum number of queues. MAX_NUM is defined in hw specific files */ -#define IWL_MIN_NUM_QUEUES 4 +/* Minimum number of queues. MAX_NUM is defined in hw specific files. + * Set the minimum to accommodate the 4 standard TX queues, 1 command + * queue, 2 (unused) HCCA queues, and 4 HT queues (one for each AC) */ +#define IWL_MIN_NUM_QUEUES 10 /* Power management (not Tx power) structures */ diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c index 956798f2c80..2f50ab60bfd 100644 --- a/drivers/net/wireless/iwlwifi/iwl3945-base.c +++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c @@ -4018,10 +4018,10 @@ static int iwl3945_pci_probe(struct pci_dev *pdev, const struct pci_device_id *e SET_IEEE80211_DEV(hw, &pdev->dev); if ((iwl3945_mod_params.num_of_queues > IWL39_MAX_NUM_QUEUES) || - (iwl3945_mod_params.num_of_queues < IWL_MIN_NUM_QUEUES)) { + (iwl3945_mod_params.num_of_queues < IWL39_MIN_NUM_QUEUES)) { IWL_ERR(priv, "invalid queues_num, should be between %d and %d\n", - IWL_MIN_NUM_QUEUES, IWL39_MAX_NUM_QUEUES); + IWL39_MIN_NUM_QUEUES, IWL39_MAX_NUM_QUEUES); err = -EINVAL; goto out_ieee80211_free_hw; } -- GitLab From 2a21f86917f7a9fe13b180e895a816871a234dee Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Sat, 25 Jul 2009 15:22:59 +0300 Subject: [PATCH 0374/1342] wireless: ERR_PTR vs null iwm_wdev_alloc() returns an ERR_PTR on failure and not null. It also prints its own dev_err() message so I removed that as well. Compile tested only. Sorry. Found by smatch (http://repo.or.cz/w/smatch.git). Signed-off-by: Dan Carpenter Acked-by: Zhu Yi Signed-off-by: John W. Linville --- drivers/net/wireless/iwmc3200wifi/netdev.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) diff --git a/drivers/net/wireless/iwmc3200wifi/netdev.c b/drivers/net/wireless/iwmc3200wifi/netdev.c index aea5ccf24cc..bf294e41753 100644 --- a/drivers/net/wireless/iwmc3200wifi/netdev.c +++ b/drivers/net/wireless/iwmc3200wifi/netdev.c @@ -106,10 +106,8 @@ void *iwm_if_alloc(int sizeof_bus, struct device *dev, int ret = 0; wdev = iwm_wdev_alloc(sizeof_bus, dev); - if (!wdev) { - dev_err(dev, "no memory for wireless device instance\n"); - return ERR_PTR(-ENOMEM); - } + if (IS_ERR(wdev)) + return wdev; iwm = wdev_to_iwm(wdev); iwm->bus_ops = if_ops; -- GitLab From 3d0ccd021b23c18ea2d399fe4a43c955485c765c Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Sat, 25 Jul 2009 23:02:32 +0200 Subject: [PATCH 0375/1342] airo: Buffer overflow SSID_rid has space for only 3 ssids. txPowerLevels[i] is read before the bounds check for i Signed-off-by: Roel Kluin Acked-by: Dan Williams Signed-off-by: John W. Linville --- drivers/net/wireless/airo.c | 13 ++++++------- 1 file changed, 6 insertions(+), 7 deletions(-) diff --git a/drivers/net/wireless/airo.c b/drivers/net/wireless/airo.c index c70604f0329..8ce5e4cee16 100644 --- a/drivers/net/wireless/airo.c +++ b/drivers/net/wireless/airo.c @@ -5918,20 +5918,19 @@ static int airo_set_essid(struct net_device *dev, readSsidRid(local, &SSID_rid); /* Check if we asked for `any' */ - if(dwrq->flags == 0) { + if (dwrq->flags == 0) { /* Just send an empty SSID list */ memset(&SSID_rid, 0, sizeof(SSID_rid)); } else { - int index = (dwrq->flags & IW_ENCODE_INDEX) - 1; + unsigned index = (dwrq->flags & IW_ENCODE_INDEX) - 1; /* Check the size of the string */ - if(dwrq->length > IW_ESSID_MAX_SIZE) { + if (dwrq->length > IW_ESSID_MAX_SIZE) return -E2BIG ; - } + /* Check if index is valid */ - if((index < 0) || (index >= 4)) { + if (index >= ARRAY_SIZE(SSID_rid.ssids)) return -EINVAL; - } /* Set the SSID */ memset(SSID_rid.ssids[index].ssid, 0, @@ -6819,7 +6818,7 @@ static int airo_set_txpow(struct net_device *dev, return -EINVAL; } clear_bit (FLAG_RADIO_OFF, &local->flags); - for (i = 0; cap_rid.txPowerLevels[i] && (i < 8); i++) + for (i = 0; i < 8 && cap_rid.txPowerLevels[i]; i++) if (v == cap_rid.txPowerLevels[i]) { readConfigRid(local, 1); local->config.txPower = v; -- GitLab From 008749fc9917b799c469478141ddd1a4c81d06ca Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Sat, 25 Jul 2009 23:21:22 +0200 Subject: [PATCH 0376/1342] ath9k: Read outside array bounds Incorrect limits leads to reads outside array bounds. Signed-off-by: Roel Kluin Acked-by: Luis R. Rodriguez Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/eeprom.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/wireless/ath/ath9k/eeprom.c b/drivers/net/wireless/ath/ath9k/eeprom.c index a2fda702b62..ce0e86c36a8 100644 --- a/drivers/net/wireless/ath/ath9k/eeprom.c +++ b/drivers/net/wireless/ath/ath9k/eeprom.c @@ -460,7 +460,7 @@ static int ath9k_hw_4k_check_eeprom(struct ath_hw *ah) integer = swab32(eep->modalHeader.antCtrlCommon); eep->modalHeader.antCtrlCommon = integer; - for (i = 0; i < AR5416_MAX_CHAINS; i++) { + for (i = 0; i < AR5416_EEP4K_MAX_CHAINS; i++) { integer = swab32(eep->modalHeader.antCtrlChain[i]); eep->modalHeader.antCtrlChain[i] = integer; } @@ -914,7 +914,7 @@ static void ath9k_hw_set_4k_power_per_rate_table(struct ath_hw *ah, ctlMode, numCtlModes, isHt40CtlMode, (pCtlMode[ctlMode] & EXT_ADDITIVE)); - for (i = 0; (i < AR5416_NUM_CTLS) && + for (i = 0; (i < AR5416_EEP4K_NUM_CTLS) && pEepData->ctlIndex[i]; i++) { DPRINTF(ah->ah_sc, ATH_DBG_EEPROM, " LOOP-Ctlidx %d: cfgCtl 0x%2.2x " -- GitLab From 082e708acc50a5b625b9bde0bb1af90dfdbd1942 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Sat, 25 Jul 2009 23:34:31 +0200 Subject: [PATCH 0377/1342] iwlwifi: Read outside array bounds tid is bounded (above) by the size of default_tid_to_tx_fifo (17 elements), but the size of priv->stations[].tid[] is MAX_TID_COUNT (9) elements. Signed-off-by: Roel Kluin Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-tx.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/net/wireless/iwlwifi/iwl-tx.c b/drivers/net/wireless/iwlwifi/iwl-tx.c index 5febb318636..2e89040e63b 100644 --- a/drivers/net/wireless/iwlwifi/iwl-tx.c +++ b/drivers/net/wireless/iwlwifi/iwl-tx.c @@ -1171,6 +1171,8 @@ int iwl_tx_agg_start(struct iwl_priv *priv, const u8 *ra, u16 tid, u16 *ssn) IWL_ERR(priv, "Start AGG on invalid station\n"); return -ENXIO; } + if (unlikely(tid >= MAX_TID_COUNT)) + return -EINVAL; if (priv->stations[sta_id].tid[tid].agg.state != IWL_AGG_OFF) { IWL_ERR(priv, "Start AGG when state is not IWL_AGG_OFF !\n"); -- GitLab From 78f1a8b758d57c2d2c9f3db7199cd30803854c82 Mon Sep 17 00:00:00 2001 From: "Luis R. Rodriguez" Date: Mon, 27 Jul 2009 08:38:25 -0700 Subject: [PATCH 0378/1342] mac80211: do not queue work after suspend in the dynamic ps timer Signed-off-by: Luis R. Rodriguez Signed-off-by: John W. Linville --- net/mac80211/mlme.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/mac80211/mlme.c b/net/mac80211/mlme.c index aca22b00b6a..07e7e41816b 100644 --- a/net/mac80211/mlme.c +++ b/net/mac80211/mlme.c @@ -721,7 +721,7 @@ void ieee80211_dynamic_ps_timer(unsigned long data) { struct ieee80211_local *local = (void *) data; - if (local->quiescing) + if (local->quiescing || local->suspended) return; queue_work(local->hw.workqueue, &local->dynamic_ps_enable_work); -- GitLab From b68f2fb9e73f46037fbeca5fbd4ae8a7ddd8ef6b Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Mon, 27 Jul 2009 10:58:08 +0100 Subject: [PATCH 0379/1342] tty: Fix a USB serial crash/scribble The port lock is used to protect the port state. However the port structure is freed on a hangup, then the lock taken on a close. The right fix is to drop the port on tty->shutdown() but we can't yet do that due to sleep v non-sleeping rules. Instead do the next best thing and fix it up when we are not in -rc season. Reported-by: Daniel Mack Signed-off-by: Alan Cox Tested-by: Daniel Mack Signed-off-by: Linus Torvalds --- drivers/usb/serial/usb-serial.c | 19 ++++++++++++++++++- 1 file changed, 18 insertions(+), 1 deletion(-) diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c index bd7581b3a48..3c8923f62ed 100644 --- a/drivers/usb/serial/usb-serial.c +++ b/drivers/usb/serial/usb-serial.c @@ -340,6 +340,22 @@ static void serial_close(struct tty_struct *tty, struct file *filp) dbg("%s - port %d", __func__, port->number); + /* FIXME: + This leaves a very narrow race. Really we should do the + serial_do_free() on tty->shutdown(), but tty->shutdown can + be called from IRQ context and serial_do_free can sleep. + + The right fix is probably to make the tty free (which is rare) + and thus tty->shutdown() occur via a work queue and simplify all + the drivers that use it. + */ + if (tty_hung_up_p(filp)) { + /* serial_hangup already called serial_down at this point. + Another user may have already reopened the port but + serial_do_free is refcounted */ + serial_do_free(port); + return; + } if (tty_port_close_start(&port->port, tty, filp) == 0) return; @@ -355,7 +371,8 @@ static void serial_hangup(struct tty_struct *tty) struct usb_serial_port *port = tty->driver_data; serial_do_down(port); tty_port_hangup(&port->port); - serial_do_free(port); + /* We must not free port yet - the USB serial layer depends on it's + continued existence */ } static int serial_write(struct tty_struct *tty, const unsigned char *buf, -- GitLab From 0e83815be719d3391bf5ea24b7fe696c07dbd417 Mon Sep 17 00:00:00 2001 From: Robert Richter Date: Mon, 27 Jul 2009 19:43:52 +0200 Subject: [PATCH 0380/1342] x86: fix section mismatch for i386 init code Startup code for i386 in arch/x86/kernel/head_32.S is using the reference variable initial_code that is located in the .cpuinit.data section. If CONFIG_HOTPLUG_CPU is enabled, startup code is not in an init section and can be called later too. In this case the reference initial_code must be kept too. This patch fixes this. See below for the section mismatch warning. WARNING: vmlinux.o(.cpuinit.data+0x0): Section mismatch in reference from the variable initial_code to the function .init.text:i386_start_kernel() The variable __cpuinitdata initial_code references a function __init i386_start_kernel(). If i386_start_kernel is only used by initial_code then annotate i386_start_kernel with a matching annotation. Signed-off-by: Robert Richter LKML-Reference: <1248716632-26844-1-git-send-email-robert.richter@amd.com> Signed-off-by: H. Peter Anvin --- arch/x86/kernel/head_32.S | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/arch/x86/kernel/head_32.S b/arch/x86/kernel/head_32.S index 8663afb5653..0d98a01cbdb 100644 --- a/arch/x86/kernel/head_32.S +++ b/arch/x86/kernel/head_32.S @@ -602,7 +602,11 @@ ignore_int: #endif iret -.section .cpuinit.data,"wa" +#ifndef CONFIG_HOTPLUG_CPU + __CPUINITDATA +#else + __REFDATA +#endif .align 4 ENTRY(initial_code) .long i386_start_kernel -- GitLab From 7cb7f45c7feef43c8f71f5cfedfc0b19be2142f7 Mon Sep 17 00:00:00 2001 From: Len Brown Date: Mon, 27 Jul 2009 18:42:38 -0400 Subject: [PATCH 0381/1342] Revert "ACPICA: Remove obsolete acpi_os_validate_address interface" This reverts commit f9ca058430333c9a24c5ca926aa445125f88df18. which caused a regression: http://bugzilla.kernel.org/show_bug.cgi?id=13620 Signed-off-by: Lin Ming Signed-off-by: Len Brown --- drivers/acpi/acpica/acobject.h | 1 + drivers/acpi/acpica/dsopcode.c | 24 ++++++++++++++++++++++++ drivers/acpi/acpica/exfldio.c | 6 ++++++ include/acpi/acpiosxf.h | 4 ++++ 4 files changed, 35 insertions(+) diff --git a/drivers/acpi/acpica/acobject.h b/drivers/acpi/acpica/acobject.h index 544dcf83492..eb6f038b03d 100644 --- a/drivers/acpi/acpica/acobject.h +++ b/drivers/acpi/acpica/acobject.h @@ -97,6 +97,7 @@ #define AOPOBJ_OBJECT_INITIALIZED 0x08 #define AOPOBJ_SETUP_COMPLETE 0x10 #define AOPOBJ_SINGLE_DATUM 0x20 +#define AOPOBJ_INVALID 0x40 /* Used if host OS won't allow an op_region address */ /****************************************************************************** * diff --git a/drivers/acpi/acpica/dsopcode.c b/drivers/acpi/acpica/dsopcode.c index 584d766e6f1..b79978f7bc7 100644 --- a/drivers/acpi/acpica/dsopcode.c +++ b/drivers/acpi/acpica/dsopcode.c @@ -397,6 +397,30 @@ acpi_status acpi_ds_get_region_arguments(union acpi_operand_object *obj_desc) status = acpi_ds_execute_arguments(node, acpi_ns_get_parent_node(node), extra_desc->extra.aml_length, extra_desc->extra.aml_start); + if (ACPI_FAILURE(status)) { + return_ACPI_STATUS(status); + } + + /* Validate the region address/length via the host OS */ + + status = acpi_os_validate_address(obj_desc->region.space_id, + obj_desc->region.address, + (acpi_size) obj_desc->region.length, + acpi_ut_get_node_name(node)); + + if (ACPI_FAILURE(status)) { + /* + * Invalid address/length. We will emit an error message and mark + * the region as invalid, so that it will cause an additional error if + * it is ever used. Then return AE_OK. + */ + ACPI_EXCEPTION((AE_INFO, status, + "During address validation of OpRegion [%4.4s]", + node->name.ascii)); + obj_desc->common.flags |= AOPOBJ_INVALID; + status = AE_OK; + } + return_ACPI_STATUS(status); } diff --git a/drivers/acpi/acpica/exfldio.c b/drivers/acpi/acpica/exfldio.c index d4075b82102..6687be167f5 100644 --- a/drivers/acpi/acpica/exfldio.c +++ b/drivers/acpi/acpica/exfldio.c @@ -113,6 +113,12 @@ acpi_ex_setup_region(union acpi_operand_object *obj_desc, } } + /* Exit if Address/Length have been disallowed by the host OS */ + + if (rgn_desc->common.flags & AOPOBJ_INVALID) { + return_ACPI_STATUS(AE_AML_ILLEGAL_ADDRESS); + } + /* * Exit now for SMBus address space, it has a non-linear address space * and the request cannot be directly validated diff --git a/include/acpi/acpiosxf.h b/include/acpi/acpiosxf.h index 3e798593b17..ab0b85cf21f 100644 --- a/include/acpi/acpiosxf.h +++ b/include/acpi/acpiosxf.h @@ -242,6 +242,10 @@ acpi_os_derive_pci_id(acpi_handle rhandle, acpi_status acpi_os_validate_interface(char *interface); acpi_status acpi_osi_invalidate(char* interface); +acpi_status +acpi_os_validate_address(u8 space_id, acpi_physical_address address, + acpi_size length, char *name); + u64 acpi_os_get_timer(void); acpi_status acpi_os_signal(u32 function, void *info); -- GitLab From 3a54297478e6578f96fd54bf4daa1751130aca86 Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Mon, 27 Jul 2009 22:17:51 +0100 Subject: [PATCH 0382/1342] pty: quickfix for the pty ENXIO timing problems This also makes close stall in the normal case which is apparently needed to fix emacs Signed-off-by: Alan Cox Signed-off-by: Linus Torvalds --- drivers/char/pty.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/char/pty.c b/drivers/char/pty.c index 6e6942c45f5..3850a68f265 100644 --- a/drivers/char/pty.c +++ b/drivers/char/pty.c @@ -52,6 +52,7 @@ static void pty_close(struct tty_struct *tty, struct file *filp) return; tty->link->packet = 0; set_bit(TTY_OTHER_CLOSED, &tty->link->flags); + tty_flip_buffer_push(tty->link); wake_up_interruptible(&tty->link->read_wait); wake_up_interruptible(&tty->link->write_wait); if (tty->driver->subtype == PTY_TYPE_MASTER) { @@ -207,6 +208,7 @@ static int pty_open(struct tty_struct *tty, struct file *filp) clear_bit(TTY_OTHER_CLOSED, &tty->link->flags); set_bit(TTY_THROTTLED, &tty->flags); retval = 0; + tty->low_latency = 1; out: return retval; } -- GitLab From 626f5cefc60b281a00db1402b82deff82080c70a Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Tue, 28 Jul 2009 00:54:39 +0200 Subject: [PATCH 0383/1342] ALSA: hda - Add quirk for Dell Studio 1555 Added a quirk entry for Dell Studio 1555. Reference: Novell bnc#525244 https://bugzilla.novell.com/show_bug.cgi?id=525244 Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_sigmatel.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/sound/pci/hda/patch_sigmatel.c b/sound/pci/hda/patch_sigmatel.c index 512f3b9b9a4..5383d8cff88 100644 --- a/sound/pci/hda/patch_sigmatel.c +++ b/sound/pci/hda/patch_sigmatel.c @@ -1809,6 +1809,8 @@ static struct snd_pci_quirk stac92hd73xx_cfg_tbl[] = { "Dell Studio 1537", STAC_DELL_M6_DMIC), SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x02a0, "Dell Studio 17", STAC_DELL_M6_DMIC), + SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x02be, + "Dell Studio 1555", STAC_DELL_M6_DMIC), {} /* terminator */ }; -- GitLab From c56d300086140c93dc3390e5300fd17df802ec0e Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Tue, 28 Jul 2009 00:34:58 +0100 Subject: [PATCH 0384/1342] usb_serial: Fix remaining ref count/lock bugs This fixes - locking bug that was hidden by ecc2e05e739c30870c8e4f252b63a0c4041f2724 - Regression #13821 - Spurious warning when closing and blocking for data write out With these changes my PL2303 always ends up as ttyUSB0 when it should and the module refcounts stay correct. I'll do a more wholesale split & tidy of _open in the next release or two as we get a standard tty_port_open and port->ops->init port->ops->shutdown call backs. Copy sent to Alan Stern and Carlos Mafra just to confirm it fixes all the reports but it passes local testing with the same hardware as Alan Stern. Signed-off-by: Alan Cox Signed-off-by: Linus Torvalds --- drivers/usb/serial/usb-serial.c | 17 +++++++++++++---- 1 file changed, 13 insertions(+), 4 deletions(-) diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c index 3c8923f62ed..99188c92068 100644 --- a/drivers/usb/serial/usb-serial.c +++ b/drivers/usb/serial/usb-serial.c @@ -32,6 +32,7 @@ #include #include #include +#include #include #include #include "pl2303.h" @@ -184,6 +185,7 @@ static int serial_open (struct tty_struct *tty, struct file *filp) struct usb_serial_port *port; unsigned int portNumber; int retval = 0; + int first = 0; dbg("%s", __func__); @@ -223,7 +225,7 @@ static int serial_open (struct tty_struct *tty, struct file *filp) /* If the console is attached, the device is already open */ if (port->port.count == 1 && !port->console) { - + first = 1; /* lock this module before we call it * this may fail, which means we must bail out, * safe because we are called with BKL held */ @@ -246,13 +248,21 @@ static int serial_open (struct tty_struct *tty, struct file *filp) if (retval) goto bailout_interface_put; mutex_unlock(&serial->disc_mutex); + set_bit(ASYNCB_INITIALIZED, &port->port.flags); } mutex_unlock(&port->mutex); /* Now do the correct tty layer semantics */ retval = tty_port_block_til_ready(&port->port, tty, filp); - if (retval == 0) + if (retval == 0) { + if (!first) + usb_serial_put(serial); return 0; - + } + mutex_lock(&port->mutex); + if (first == 0) + goto bailout_mutex_unlock; + /* Undo the initial port actions */ + mutex_lock(&serial->disc_mutex); bailout_interface_put: usb_autopm_put_interface(serial->interface); bailout_module_put: @@ -411,7 +421,6 @@ static int serial_chars_in_buffer(struct tty_struct *tty) struct usb_serial_port *port = tty->driver_data; dbg("%s = port %d", __func__, port->number); - WARN_ON(!port->port.count); /* if the device was unplugged then any remaining characters fell out of the connector ;) */ if (port->serial->disconnected) -- GitLab From 4733fd328f14280900435d9dbae1487d110a4d56 Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Tue, 28 Jul 2009 10:16:48 +1000 Subject: [PATCH 0385/1342] mm: Remove duplicate definitions in MIPS and SH Those definitions are already provided by asm-generic Signed-off-by: Benjamin Herrenschmidt Acked-by: Paul Mundt Signed-off-by: Linus Torvalds --- arch/mips/include/asm/pgalloc.h | 11 ----------- arch/sh/include/asm/pgalloc.h | 8 -------- 2 files changed, 19 deletions(-) diff --git a/arch/mips/include/asm/pgalloc.h b/arch/mips/include/asm/pgalloc.h index f705735feef..3738f4b48cb 100644 --- a/arch/mips/include/asm/pgalloc.h +++ b/arch/mips/include/asm/pgalloc.h @@ -104,17 +104,6 @@ do { \ tlb_remove_page((tlb), pte); \ } while (0) -#ifdef CONFIG_32BIT - -/* - * allocating and freeing a pmd is trivial: the 1-entry pmd is - * inside the pgd, so has no extra memory associated with it. - */ -#define pmd_free(mm, x) do { } while (0) -#define __pmd_free_tlb(tlb, x, addr) do { } while (0) - -#endif - #ifdef CONFIG_64BIT static inline pmd_t *pmd_alloc_one(struct mm_struct *mm, unsigned long address) diff --git a/arch/sh/include/asm/pgalloc.h b/arch/sh/include/asm/pgalloc.h index 89a482750a5..63ca37bd9a9 100644 --- a/arch/sh/include/asm/pgalloc.h +++ b/arch/sh/include/asm/pgalloc.h @@ -79,14 +79,6 @@ do { \ tlb_remove_page((tlb), (pte)); \ } while (0) -/* - * allocating and freeing a pmd is trivial: the 1-entry pmd is - * inside the pgd, so has no extra memory associated with it. - */ - -#define pmd_free(mm, x) do { } while (0) -#define __pmd_free_tlb(tlb,x,addr) do { } while (0) - static inline void check_pgt_cache(void) { quicklist_trim(QUICK_PGD, NULL, 25, 16); -- GitLab From 7b91e2661addd8e2419cb45f6a322aa5dab9bcee Mon Sep 17 00:00:00 2001 From: Jeff Layton Date: Thu, 23 Jul 2009 15:22:30 -0400 Subject: [PATCH 0386/1342] cifs: fix error handling in mount-time DFS referral chasing code If the referral is malformed or the hostname can't be resolved, then the current code generates an oops. Fix it to handle these errors gracefully. Reported-by: Sandro Mathys Acked-by: Igor Mammedov CC: Stable Signed-off-by: Jeff Layton Signed-off-by: Steve French --- fs/cifs/cifs_dfs_ref.c | 12 +++++++++--- fs/cifs/connect.c | 13 ++++++++++--- 2 files changed, 19 insertions(+), 6 deletions(-) diff --git a/fs/cifs/cifs_dfs_ref.c b/fs/cifs/cifs_dfs_ref.c index 3bb11be8b6a..606912d8f2a 100644 --- a/fs/cifs/cifs_dfs_ref.c +++ b/fs/cifs/cifs_dfs_ref.c @@ -55,7 +55,7 @@ void cifs_dfs_release_automount_timer(void) * i.e. strips from UNC trailing path that is not part of share * name and fixup missing '\' in the begining of DFS node refferal * if neccessary. - * Returns pointer to share name on success or NULL on error. + * Returns pointer to share name on success or ERR_PTR on error. * Caller is responsible for freeing returned string. */ static char *cifs_get_share_name(const char *node_name) @@ -68,7 +68,7 @@ static char *cifs_get_share_name(const char *node_name) UNC = kmalloc(len+2 /*for term null and additional \ if it's missed */, GFP_KERNEL); if (!UNC) - return NULL; + return ERR_PTR(-ENOMEM); /* get share name and server name */ if (node_name[1] != '\\') { @@ -87,7 +87,7 @@ static char *cifs_get_share_name(const char *node_name) cERROR(1, ("%s: no server name end in node name: %s", __func__, node_name)); kfree(UNC); - return NULL; + return ERR_PTR(-EINVAL); } /* find sharename end */ @@ -133,6 +133,12 @@ char *cifs_compose_mount_options(const char *sb_mountdata, return ERR_PTR(-EINVAL); *devname = cifs_get_share_name(ref->node_name); + if (IS_ERR(*devname)) { + rc = PTR_ERR(*devname); + *devname = NULL; + goto compose_mount_options_err; + } + rc = dns_resolve_server_name_to_ip(*devname, &srvIP); if (rc != 0) { cERROR(1, ("%s: Failed to resolve server part of %s to IP: %d", diff --git a/fs/cifs/connect.c b/fs/cifs/connect.c index fc44d316d0b..f2486889b7b 100644 --- a/fs/cifs/connect.c +++ b/fs/cifs/connect.c @@ -2544,11 +2544,20 @@ remote_path_check: if (mount_data != mount_data_global) kfree(mount_data); + mount_data = cifs_compose_mount_options( cifs_sb->mountdata, full_path + 1, referrals, &fake_devname); - kfree(fake_devname); + free_dfs_info_array(referrals, num_referrals); + kfree(fake_devname); + kfree(full_path); + + if (IS_ERR(mount_data)) { + rc = PTR_ERR(mount_data); + mount_data = NULL; + goto mount_fail_check; + } if (tcon) cifs_put_tcon(tcon); @@ -2556,8 +2565,6 @@ remote_path_check: cifs_put_smb_ses(pSesInfo); cleanup_volume_info(&volume_info); - FreeXid(xid); - kfree(full_path); referral_walks_count++; goto try_mount_again; } -- GitLab From 9a926d86b29a25456f1dd8c9df938e151b1c3978 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Mon, 27 Jul 2009 18:10:28 -0700 Subject: [PATCH 0387/1342] sparc64: Sign extend length arg to truncate syscalls when compat. The first thing sys_truncate() and sys_ftruncate() do is sign extend the unsigned length arg to a signed type. Thanks to Benjamin Herrenschmidt for the tip. Signed-off-by: David S. Miller --- arch/sparc/kernel/sys32.S | 2 ++ arch/sparc/kernel/systbls_64.S | 4 ++-- 2 files changed, 4 insertions(+), 2 deletions(-) diff --git a/arch/sparc/kernel/sys32.S b/arch/sparc/kernel/sys32.S index f061c4dda9e..577f8fab8b6 100644 --- a/arch/sparc/kernel/sys32.S +++ b/arch/sparc/kernel/sys32.S @@ -138,6 +138,8 @@ SIGN2(sys32_splice, sys_splice, %o0, %o1) SIGN2(sys32_sync_file_range, compat_sync_file_range, %o0, %o5) SIGN2(sys32_tee, sys_tee, %o0, %o1) SIGN1(sys32_vmsplice, compat_sys_vmsplice, %o0) +SIGN1(sys32_truncate, sys_truncate, %o1) +SIGN1(sys32_ftruncate, sys_ftruncate, %o1) .globl sys32_mmap2 sys32_mmap2: diff --git a/arch/sparc/kernel/systbls_64.S b/arch/sparc/kernel/systbls_64.S index 6b3ee88e253..2ee7250ba7a 100644 --- a/arch/sparc/kernel/systbls_64.S +++ b/arch/sparc/kernel/systbls_64.S @@ -43,8 +43,8 @@ sys_call_table32: /*110*/ .word sys_setresgid, sys_getresgid, sys_setregid, sys_nis_syscall, sys_nis_syscall .word sys32_getgroups, compat_sys_gettimeofday, sys32_getrusage, sys_nis_syscall, sys_getcwd /*120*/ .word compat_sys_readv, compat_sys_writev, compat_sys_settimeofday, sys_fchown16, sys_fchmod - .word sys_nis_syscall, sys_setreuid16, sys_setregid16, sys_rename, sys_truncate -/*130*/ .word sys_ftruncate, sys_flock, compat_sys_lstat64, sys_nis_syscall, sys_nis_syscall + .word sys_nis_syscall, sys_setreuid16, sys_setregid16, sys_rename, sys32_truncate +/*130*/ .word sys32_ftruncate, sys_flock, compat_sys_lstat64, sys_nis_syscall, sys_nis_syscall .word sys_nis_syscall, sys32_mkdir, sys_rmdir, compat_sys_utimes, compat_sys_stat64 /*140*/ .word sys32_sendfile64, sys_nis_syscall, sys32_futex, sys_gettid, compat_sys_getrlimit .word compat_sys_setrlimit, sys_pivot_root, sys32_prctl, sys_pciconfig_read, sys_pciconfig_write -- GitLab From 27fed4175acf81ddd91d9a4ee2fd298981f60295 Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Mon, 27 Jul 2009 18:39:45 -0700 Subject: [PATCH 0388/1342] ip: fix logic of reverse path filter sysctl Even though reverse path filter was changed from simple boolean to trinary control, the loose mode only works if both all and device are configured because of this logic error. Signed-off-by: Stephen Hemminger Signed-off-by: David S. Miller --- include/linux/inetdevice.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/linux/inetdevice.h b/include/linux/inetdevice.h index acef2a770b6..ad27c7da879 100644 --- a/include/linux/inetdevice.h +++ b/include/linux/inetdevice.h @@ -82,7 +82,7 @@ static inline void ipv4_devconf_setall(struct in_device *in_dev) #define IN_DEV_FORWARD(in_dev) IN_DEV_CONF_GET((in_dev), FORWARDING) #define IN_DEV_MFORWARD(in_dev) IN_DEV_ANDCONF((in_dev), MC_FORWARDING) -#define IN_DEV_RPFILTER(in_dev) IN_DEV_ANDCONF((in_dev), RP_FILTER) +#define IN_DEV_RPFILTER(in_dev) IN_DEV_MAXCONF((in_dev), RP_FILTER) #define IN_DEV_SOURCE_ROUTE(in_dev) IN_DEV_ANDCONF((in_dev), \ ACCEPT_SOURCE_ROUTE) #define IN_DEV_BOOTP_RELAY(in_dev) IN_DEV_ANDCONF((in_dev), BOOTP_RELAY) -- GitLab From 48f5690d45b79ffeedc5ab24243b576056f1d2ff Mon Sep 17 00:00:00 2001 From: unsik Kim Date: Tue, 28 Jul 2009 08:52:06 +0200 Subject: [PATCH 0389/1342] mg_disk: remove prohibited sleep operation mflash's polling driver operate in standard request_fn_proc's context, sleep in this isn't permitted. Signed-off-by: unsik Kim Signed-off-by: Jens Axboe --- drivers/block/mg_disk.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/drivers/block/mg_disk.c b/drivers/block/mg_disk.c index f703f547824..5b120eab2ba 100644 --- a/drivers/block/mg_disk.c +++ b/drivers/block/mg_disk.c @@ -245,8 +245,6 @@ static unsigned int mg_wait(struct mg_host *host, u32 expect, u32 msec) mg_dump_status("not ready", status, host); return MG_ERR_INV_STAT; } - if (prv_data->use_polling) - msleep(1); status = inb((unsigned long)host->dev_base + MG_REG_STATUS); } while (time_before(cur_jiffies, expire)); -- GitLab From eb32baec15c38ae6f06cb898a9f791578c5f8c79 Mon Sep 17 00:00:00 2001 From: unsik Kim Date: Tue, 28 Jul 2009 08:52:07 +0200 Subject: [PATCH 0390/1342] mg_disk: fix reading invalid status when use polling driver When using polling driver, little delay is required to access status register. Without this, host might read invalid status. Signed-off-by: unsik Kim Signed-off-by: Jens Axboe --- drivers/block/mg_disk.c | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/drivers/block/mg_disk.c b/drivers/block/mg_disk.c index 5b120eab2ba..6440d594541 100644 --- a/drivers/block/mg_disk.c +++ b/drivers/block/mg_disk.c @@ -219,6 +219,16 @@ static unsigned int mg_wait(struct mg_host *host, u32 expect, u32 msec) host->error = MG_ERR_NONE; expire = jiffies + msecs_to_jiffies(msec); + /* These 2 times dummy status read prevents reading invalid + * status. A very little time (3 times of mflash operating clk) + * is required for busy bit is set. Use dummy read instead of + * busy wait, because mflash's PLL is machine dependent. + */ + if (prv_data->use_polling) { + status = inb((unsigned long)host->dev_base + MG_REG_STATUS); + status = inb((unsigned long)host->dev_base + MG_REG_STATUS); + } + status = inb((unsigned long)host->dev_base + MG_REG_STATUS); do { -- GitLab From 394c6cc63c1d6900ad7498a3221a1d48fc00c4fa Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Tue, 28 Jul 2009 08:56:34 +0200 Subject: [PATCH 0391/1342] mg_disk: fix issue with data integrity on error in mg_write() We cannot acknowledge the sector write before checking its status (which is done on the next loop iteration) and we also need to do the final status register check after writing the last sector. Fix mg_write() to match mg_write_intr() in this regard. While at it: - add mg_read_one() and mg_write_one() helpers - always use MG_SECTOR_SIZE and remove MG_STORAGE_BUFFER_SIZE [bart: thanks to Tejun for porting the patch over recent block changes] Cc: unsik Kim Cc: Tejun Heo Signed-off-by: Bartlomiej Zolnierkiewicz =================================================================== Signed-off-by: Jens Axboe --- drivers/block/mg_disk.c | 89 ++++++++++++++++++++++------------------- 1 file changed, 47 insertions(+), 42 deletions(-) diff --git a/drivers/block/mg_disk.c b/drivers/block/mg_disk.c index 6440d594541..19917d5481b 100644 --- a/drivers/block/mg_disk.c +++ b/drivers/block/mg_disk.c @@ -36,7 +36,6 @@ /* Register offsets */ #define MG_BUFF_OFFSET 0x8000 -#define MG_STORAGE_BUFFER_SIZE 0x200 #define MG_REG_OFFSET 0xC000 #define MG_REG_FEATURE (MG_REG_OFFSET + 2) /* write case */ #define MG_REG_ERROR (MG_REG_OFFSET + 2) /* read case */ @@ -477,9 +476,18 @@ static unsigned int mg_out(struct mg_host *host, return MG_ERR_NONE; } +static void mg_read_one(struct mg_host *host, struct request *req) +{ + u16 *buff = (u16 *)req->buffer; + u32 i; + + for (i = 0; i < MG_SECTOR_SIZE >> 1; i++) + *buff++ = inw((unsigned long)host->dev_base + MG_BUFF_OFFSET + + (i << 1)); +} + static void mg_read(struct request *req) { - u32 j; struct mg_host *host = req->rq_disk->private_data; if (mg_out(host, blk_rq_pos(req), blk_rq_sectors(req), @@ -490,26 +498,33 @@ static void mg_read(struct request *req) blk_rq_sectors(req), blk_rq_pos(req), req->buffer); do { - u16 *buff = (u16 *)req->buffer; - if (mg_wait(host, ATA_DRQ, MG_TMAX_WAIT_RD_DRQ) != MG_ERR_NONE) { mg_bad_rw_intr(host); return; } - for (j = 0; j < MG_SECTOR_SIZE >> 1; j++) - *buff++ = inw((unsigned long)host->dev_base + - MG_BUFF_OFFSET + (j << 1)); + + mg_read_one(host, req); outb(MG_CMD_RD_CONF, (unsigned long)host->dev_base + MG_REG_COMMAND); } while (mg_end_request(host, 0, MG_SECTOR_SIZE)); } +static void mg_write_one(struct mg_host *host, struct request *req) +{ + u16 *buff = (u16 *)req->buffer; + u32 i; + + for (i = 0; i < MG_SECTOR_SIZE >> 1; i++) + outw(*buff++, (unsigned long)host->dev_base + MG_BUFF_OFFSET + + (i << 1)); +} + static void mg_write(struct request *req) { - u32 j; struct mg_host *host = req->rq_disk->private_data; + bool rem; if (mg_out(host, blk_rq_pos(req), blk_rq_sectors(req), MG_CMD_WR, NULL) != MG_ERR_NONE) { @@ -520,27 +535,37 @@ static void mg_write(struct request *req) MG_DBG("requested %d sects (from %ld), buffer=0x%p\n", blk_rq_sectors(req), blk_rq_pos(req), req->buffer); - do { - u16 *buff = (u16 *)req->buffer; + if (mg_wait(host, ATA_DRQ, + MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) { + mg_bad_rw_intr(host); + return; + } + + mg_write_one(host, req); + + outb(MG_CMD_WR_CONF, (unsigned long)host->dev_base + MG_REG_COMMAND); - if (mg_wait(host, ATA_DRQ, MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) { + do { + if (blk_rq_sectors(req) > 1 && + mg_wait(host, ATA_DRQ, + MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) { mg_bad_rw_intr(host); return; } - for (j = 0; j < MG_SECTOR_SIZE >> 1; j++) - outw(*buff++, (unsigned long)host->dev_base + - MG_BUFF_OFFSET + (j << 1)); - outb(MG_CMD_WR_CONF, (unsigned long)host->dev_base + - MG_REG_COMMAND); - } while (mg_end_request(host, 0, MG_SECTOR_SIZE)); + rem = mg_end_request(host, 0, MG_SECTOR_SIZE); + if (rem) + mg_write_one(host, req); + + outb(MG_CMD_WR_CONF, + (unsigned long)host->dev_base + MG_REG_COMMAND); + } while (rem); } static void mg_read_intr(struct mg_host *host) { struct request *req = host->req; u32 i; - u16 *buff; /* check status */ do { @@ -558,13 +583,7 @@ static void mg_read_intr(struct mg_host *host) return; ok_to_read: - /* get current segment of request */ - buff = (u16 *)req->buffer; - - /* read 1 sector */ - for (i = 0; i < MG_SECTOR_SIZE >> 1; i++) - *buff++ = inw((unsigned long)host->dev_base + MG_BUFF_OFFSET + - (i << 1)); + mg_read_one(host, req); MG_DBG("sector %ld, remaining=%ld, buffer=0x%p\n", blk_rq_pos(req), blk_rq_sectors(req) - 1, req->buffer); @@ -583,8 +602,7 @@ ok_to_read: static void mg_write_intr(struct mg_host *host) { struct request *req = host->req; - u32 i, j; - u16 *buff; + u32 i; bool rem; /* check status */ @@ -605,12 +623,7 @@ static void mg_write_intr(struct mg_host *host) ok_to_write: if ((rem = mg_end_request(host, 0, MG_SECTOR_SIZE))) { /* write 1 sector and set handler if remains */ - buff = (u16 *)req->buffer; - for (j = 0; j < MG_STORAGE_BUFFER_SIZE >> 1; j++) { - outw(*buff, (unsigned long)host->dev_base + - MG_BUFF_OFFSET + (j << 1)); - buff++; - } + mg_write_one(host, req); MG_DBG("sector %ld, remaining=%ld, buffer=0x%p\n", blk_rq_pos(req), blk_rq_sectors(req), req->buffer); host->mg_do_intr = mg_write_intr; @@ -675,9 +688,6 @@ static unsigned int mg_issue_req(struct request *req, unsigned int sect_num, unsigned int sect_cnt) { - u16 *buff; - u32 i; - switch (rq_data_dir(req)) { case READ: if (mg_out(host, sect_num, sect_cnt, MG_CMD_RD, &mg_read_intr) @@ -701,12 +711,7 @@ static unsigned int mg_issue_req(struct request *req, mg_bad_rw_intr(host); return host->error; } - buff = (u16 *)req->buffer; - for (i = 0; i < MG_SECTOR_SIZE >> 1; i++) { - outw(*buff, (unsigned long)host->dev_base + - MG_BUFF_OFFSET + (i << 1)); - buff++; - } + mg_write_one(host, req); mod_timer(&host->timer, jiffies + 3 * HZ); outb(MG_CMD_WR_CONF, (unsigned long)host->dev_base + MG_REG_COMMAND); -- GitLab From a85a00a699740f6f9863f88aef22060fe1534681 Mon Sep 17 00:00:00 2001 From: unsik Kim Date: Tue, 28 Jul 2009 08:57:33 +0200 Subject: [PATCH 0392/1342] mg_disk: Add missing ready status check on mg_write() When last sector is written, ready bit of status register should be checked. Signed-off-by: unsik Kim Acked-by: Bartlomiej Zolnierkiewicz Signed-off-by: Jens Axboe --- drivers/block/mg_disk.c | 32 +++++++++++++++----------------- 1 file changed, 15 insertions(+), 17 deletions(-) diff --git a/drivers/block/mg_disk.c b/drivers/block/mg_disk.c index 19917d5481b..6d7fbaa9224 100644 --- a/drivers/block/mg_disk.c +++ b/drivers/block/mg_disk.c @@ -524,16 +524,16 @@ static void mg_write_one(struct mg_host *host, struct request *req) static void mg_write(struct request *req) { struct mg_host *host = req->rq_disk->private_data; - bool rem; + unsigned int rem = blk_rq_sectors(req); - if (mg_out(host, blk_rq_pos(req), blk_rq_sectors(req), + if (mg_out(host, blk_rq_pos(req), rem, MG_CMD_WR, NULL) != MG_ERR_NONE) { mg_bad_rw_intr(host); return; } MG_DBG("requested %d sects (from %ld), buffer=0x%p\n", - blk_rq_sectors(req), blk_rq_pos(req), req->buffer); + rem, blk_rq_pos(req), req->buffer); if (mg_wait(host, ATA_DRQ, MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) { @@ -541,25 +541,23 @@ static void mg_write(struct request *req) return; } - mg_write_one(host, req); + do { + mg_write_one(host, req); - outb(MG_CMD_WR_CONF, (unsigned long)host->dev_base + MG_REG_COMMAND); + outb(MG_CMD_WR_CONF, (unsigned long)host->dev_base + + MG_REG_COMMAND); - do { - if (blk_rq_sectors(req) > 1 && - mg_wait(host, ATA_DRQ, - MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) { + rem--; + if (rem > 1 && mg_wait(host, ATA_DRQ, + MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) { + mg_bad_rw_intr(host); + return; + } else if (mg_wait(host, MG_STAT_READY, + MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) { mg_bad_rw_intr(host); return; } - - rem = mg_end_request(host, 0, MG_SECTOR_SIZE); - if (rem) - mg_write_one(host, req); - - outb(MG_CMD_WR_CONF, - (unsigned long)host->dev_base + MG_REG_COMMAND); - } while (rem); + } while (mg_end_request(host, 0, MG_SECTOR_SIZE)); } static void mg_read_intr(struct mg_host *host) -- GitLab From a4e7d46407d73f35d217013b363b79a8f8eafcaa Mon Sep 17 00:00:00 2001 From: Jens Axboe Date: Tue, 28 Jul 2009 09:07:29 +0200 Subject: [PATCH 0393/1342] block: always assign default lock to queues Move the assignment of a default lock below blk_init_queue() to blk_queue_make_request(), so we also get to set the default lock for ->make_request_fn() based drivers. This is important since the queue flag locking requires a lock to be in place. Signed-off-by: Jens Axboe --- block/blk-core.c | 7 ------- block/blk-settings.c | 7 +++++++ 2 files changed, 7 insertions(+), 7 deletions(-) diff --git a/block/blk-core.c b/block/blk-core.c index 4b45435c6ea..a0c340d239b 100644 --- a/block/blk-core.c +++ b/block/blk-core.c @@ -575,13 +575,6 @@ blk_init_queue_node(request_fn_proc *rfn, spinlock_t *lock, int node_id) return NULL; } - /* - * if caller didn't supply a lock, they get per-queue locking with - * our embedded lock - */ - if (!lock) - lock = &q->__queue_lock; - q->request_fn = rfn; q->prep_rq_fn = NULL; q->unplug_fn = generic_unplug_device; diff --git a/block/blk-settings.c b/block/blk-settings.c index bd582a7f531..8a3ea3bba10 100644 --- a/block/blk-settings.c +++ b/block/blk-settings.c @@ -164,6 +164,13 @@ void blk_queue_make_request(struct request_queue *q, make_request_fn *mfn) blk_set_default_limits(&q->limits); + /* + * If the caller didn't supply a lock, fall back to our embedded + * per-queue locks + */ + if (!q->queue_lock) + q->queue_lock = &q->__queue_lock; + /* * by default assume old behaviour and bounce for any highmem page */ -- GitLab From 3839e4b29b4385e4b31075e7805683e2aa2a8103 Mon Sep 17 00:00:00 2001 From: Xiaotian Feng Date: Tue, 28 Jul 2009 09:11:14 +0200 Subject: [PATCH 0394/1342] block: fix improper kobject release in blk_integrity_unregister blk_integrity_unregister should use kobject_put to release the kobject, otherwise after bi is freed, memory of bi->kobj->name is leaked. Signed-off-by: Xiaotian Feng Signed-off-by: Jens Axboe --- block/blk-integrity.c | 1 + 1 file changed, 1 insertion(+) diff --git a/block/blk-integrity.c b/block/blk-integrity.c index 73e28d35568..15c630813b1 100644 --- a/block/blk-integrity.c +++ b/block/blk-integrity.c @@ -379,6 +379,7 @@ void blk_integrity_unregister(struct gendisk *disk) kobject_uevent(&bi->kobj, KOBJ_REMOVE); kobject_del(&bi->kobj); + kobject_put(&bi->kobj); kmem_cache_free(integrity_cachep, bi); disk->integrity = NULL; } -- GitLab From 8666f8deec75a8dce15edd35ec33d29ef79cdb08 Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Fri, 24 Jul 2009 17:30:50 +0200 Subject: [PATCH 0395/1342] mx27 defconfig update - enable MX27_3DS and MX27LITE Board - enable MXC nand driver - enable UBI support Signed-off-by: Sascha Hauer --- arch/arm/configs/mx27_defconfig | 270 ++++++++++++++++++++++---------- 1 file changed, 185 insertions(+), 85 deletions(-) diff --git a/arch/arm/configs/mx27_defconfig b/arch/arm/configs/mx27_defconfig index 083516cd0d7..75263a83741 100644 --- a/arch/arm/configs/mx27_defconfig +++ b/arch/arm/configs/mx27_defconfig @@ -1,15 +1,15 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc1 -# Wed Apr 8 10:18:06 2009 +# Linux kernel version: 2.6.31-rc4 +# Fri Jul 24 16:08:06 2009 # CONFIG_ARM=y +CONFIG_HAVE_PWM=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y CONFIG_GENERIC_GPIO=y CONFIG_GENERIC_TIME=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_MMU=y -# CONFIG_NO_IOPORT is not set CONFIG_GENERIC_HARDIRQS=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y @@ -18,14 +18,13 @@ CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_HARDIRQS_SW_RESEND=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_RWSEM_GENERIC_SPINLOCK=y -# CONFIG_ARCH_HAS_ILOG2_U32 is not set -# CONFIG_ARCH_HAS_ILOG2_U64 is not set CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_ARCH_MTD_XIP=y CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y CONFIG_VECTORS_BASE=0xffff0000 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -85,7 +84,12 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y + +# +# Performance Counters +# CONFIG_VM_EVENT_COUNTERS=y +# CONFIG_STRIP_ASM_SYMS is not set # CONFIG_COMPAT_BRK is not set CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -99,6 +103,12 @@ CONFIG_KPROBES=y CONFIG_KRETPROBES=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y +CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# +# CONFIG_GCOV_KERNEL is not set # CONFIG_SLOW_WORK is not set CONFIG_HAVE_GENERIC_DMA_COHERENT=y CONFIG_SLABINFO=y @@ -111,7 +121,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -138,13 +148,14 @@ CONFIG_FREEZER=y # CONFIG_ARCH_VERSATILE is not set # CONFIG_ARCH_AT91 is not set # CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_GEMINI is not set # CONFIG_ARCH_EBSA110 is not set # CONFIG_ARCH_EP93XX is not set -# CONFIG_ARCH_GEMINI is not set # CONFIG_ARCH_FOOTBRIDGE is not set +CONFIG_ARCH_MXC=y +# CONFIG_ARCH_STMP3XXX is not set # CONFIG_ARCH_NETX is not set # CONFIG_ARCH_H720X is not set -# CONFIG_ARCH_IMX is not set # CONFIG_ARCH_IOP13XX is not set # CONFIG_ARCH_IOP32X is not set # CONFIG_ARCH_IOP33X is not set @@ -153,25 +164,25 @@ CONFIG_FREEZER=y # CONFIG_ARCH_IXP4XX is not set # CONFIG_ARCH_L7200 is not set # CONFIG_ARCH_KIRKWOOD is not set -# CONFIG_ARCH_KS8695 is not set -# CONFIG_ARCH_NS9XXX is not set # CONFIG_ARCH_LOKI is not set # CONFIG_ARCH_MV78XX0 is not set -CONFIG_ARCH_MXC=y # CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_W90X900 is not set # CONFIG_ARCH_PNX4008 is not set # CONFIG_ARCH_PXA is not set -# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_MSM is not set # CONFIG_ARCH_RPC is not set # CONFIG_ARCH_SA1100 is not set # CONFIG_ARCH_S3C2410 is not set # CONFIG_ARCH_S3C64XX is not set # CONFIG_ARCH_SHARK is not set # CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_U300 is not set # CONFIG_ARCH_DAVINCI is not set # CONFIG_ARCH_OMAP is not set -# CONFIG_ARCH_MSM is not set -# CONFIG_ARCH_W90X900 is not set # # Freescale MXC Implementations @@ -188,6 +199,8 @@ CONFIG_MACH_MX27=y CONFIG_MACH_MX27ADS=y CONFIG_MACH_PCM038=y CONFIG_MACH_PCM970_BASEBOARD=y +CONFIG_MACH_MX27_3DS=y +CONFIG_MACH_MX27LITE=y CONFIG_MXC_IRQ_PRIOR=y CONFIG_MXC_PWM=y @@ -213,7 +226,6 @@ CONFIG_ARM_THUMB=y # CONFIG_CPU_DCACHE_DISABLE is not set # CONFIG_CPU_DCACHE_WRITETHROUGH is not set # CONFIG_CPU_CACHE_ROUND_ROBIN is not set -# CONFIG_OUTER_CACHE is not set CONFIG_COMMON_CLKDEV=y # @@ -238,7 +250,6 @@ CONFIG_PREEMPT=y CONFIG_HZ=100 CONFIG_AEABI=y CONFIG_OABI_COMPAT=y -CONFIG_ARCH_FLATMEM_HAS_HOLES=y # CONFIG_ARCH_SPARSEMEM_DEFAULT is not set # CONFIG_ARCH_SELECT_MEMORY_MODEL is not set # CONFIG_HIGHMEM is not set @@ -253,10 +264,11 @@ CONFIG_SPLIT_PTLOCK_CPUS=4096 # CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_ALIGNMENT_TRAP=y +# CONFIG_UACCESS_WITH_MEMCPY is not set # # Boot options @@ -361,6 +373,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -474,7 +487,16 @@ CONFIG_MTD_PHYSMAP=y # CONFIG_MTD_DOC2000 is not set # CONFIG_MTD_DOC2001 is not set # CONFIG_MTD_DOC2001PLUS is not set -# CONFIG_MTD_NAND is not set +CONFIG_MTD_NAND=y +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +# CONFIG_MTD_NAND_GPIO is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_DISKONCHIP is not set +# CONFIG_MTD_NAND_NANDSIM is not set +# CONFIG_MTD_NAND_PLATFORM is not set +CONFIG_MTD_NAND_MXC=y # CONFIG_MTD_ONENAND is not set # @@ -485,7 +507,15 @@ CONFIG_MTD_PHYSMAP=y # # UBI - Unsorted block images # -# CONFIG_MTD_UBI is not set +CONFIG_MTD_UBI=y +CONFIG_MTD_UBI_WL_THRESHOLD=4096 +CONFIG_MTD_UBI_BEB_RESERVE=1 +# CONFIG_MTD_UBI_GLUEBI is not set + +# +# UBI debugging options +# +# CONFIG_MTD_UBI_DEBUG is not set # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_COW_COMMON is not set @@ -494,7 +524,21 @@ CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_RAM is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set -# CONFIG_MISC_DEVICES is not set +# CONFIG_MG_DISK is not set +CONFIG_MISC_DEVICES=y +# CONFIG_ICS932S401 is not set +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_ISL29003 is not set +# CONFIG_C2PORT is not set + +# +# EEPROM support +# +CONFIG_EEPROM_AT24=y +# CONFIG_EEPROM_AT25 is not set +# CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set +# CONFIG_EEPROM_93CX6 is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -508,7 +552,6 @@ CONFIG_HAVE_IDE=y # CONFIG_ATA is not set # CONFIG_MD is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -534,6 +577,8 @@ CONFIG_NET_ETHERNET=y # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set +# CONFIG_KS8851 is not set CONFIG_FEC=y # CONFIG_FEC2 is not set # CONFIG_NETDEV_1000 is not set @@ -580,6 +625,11 @@ CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_TABLET is not set CONFIG_INPUT_TOUCHSCREEN=y # CONFIG_TOUCHSCREEN_ADS7846 is not set +# CONFIG_TOUCHSCREEN_AD7877 is not set +# CONFIG_TOUCHSCREEN_AD7879_I2C is not set +# CONFIG_TOUCHSCREEN_AD7879_SPI is not set +# CONFIG_TOUCHSCREEN_AD7879 is not set +# CONFIG_TOUCHSCREEN_EETI is not set # CONFIG_TOUCHSCREEN_FUJITSU is not set # CONFIG_TOUCHSCREEN_GUNZE is not set # CONFIG_TOUCHSCREEN_ELO is not set @@ -592,6 +642,7 @@ CONFIG_INPUT_TOUCHSCREEN=y # CONFIG_TOUCHSCREEN_TOUCHWIN is not set # CONFIG_TOUCHSCREEN_TOUCHIT213 is not set # CONFIG_TOUCHSCREEN_TSC2007 is not set +# CONFIG_TOUCHSCREEN_W90X900 is not set # CONFIG_INPUT_MISC is not set # @@ -644,6 +695,7 @@ CONFIG_I2C_HELPER_AUTO=y # # I2C system bus drivers (mostly embedded / system-on-chip) # +# CONFIG_I2C_DESIGNWARE is not set # CONFIG_I2C_GPIO is not set CONFIG_I2C_IMX=y # CONFIG_I2C_OCORES is not set @@ -668,7 +720,6 @@ CONFIG_I2C_IMX=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set @@ -719,6 +770,7 @@ CONFIG_W1=y # # CONFIG_W1_MASTER_DS2482 is not set CONFIG_W1_MASTER_MXC=y +# CONFIG_W1_MASTER_DS1WM is not set # CONFIG_W1_MASTER_GPIO is not set # @@ -753,54 +805,16 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_TPS65010 is not set # CONFIG_TWL4030_CORE is not set # CONFIG_MFD_TMIO is not set +# CONFIG_MFD_T7L66XB is not set +# CONFIG_MFD_TC6387XB is not set # CONFIG_MFD_TC6393XB is not set # CONFIG_PMIC_DA903X is not set # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -CONFIG_VIDEO_DEV=y -CONFIG_VIDEO_V4L2_COMMON=y -CONFIG_VIDEO_ALLOW_V4L1=y -CONFIG_VIDEO_V4L1_COMPAT=y -# CONFIG_DVB_CORE is not set -CONFIG_VIDEO_MEDIA=y - -# -# Multimedia drivers -# -# CONFIG_MEDIA_ATTACH is not set -CONFIG_MEDIA_TUNER=y -# CONFIG_MEDIA_TUNER_CUSTOMISE is not set -CONFIG_MEDIA_TUNER_SIMPLE=y -CONFIG_MEDIA_TUNER_TDA8290=y -CONFIG_MEDIA_TUNER_TDA9887=y -CONFIG_MEDIA_TUNER_TEA5761=y -CONFIG_MEDIA_TUNER_TEA5767=y -CONFIG_MEDIA_TUNER_MT20XX=y -CONFIG_MEDIA_TUNER_XC2028=y -CONFIG_MEDIA_TUNER_XC5000=y -CONFIG_MEDIA_TUNER_MC44S803=y -CONFIG_VIDEO_V4L2=y -CONFIG_VIDEO_V4L1=y -CONFIG_VIDEO_CAPTURE_DRIVERS=y -# CONFIG_VIDEO_ADV_DEBUG is not set -# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set -CONFIG_VIDEO_HELPER_CHIPS_AUTO=y -# CONFIG_VIDEO_VIVI is not set -# CONFIG_VIDEO_CPIA is not set -# CONFIG_VIDEO_SAA5246A is not set -# CONFIG_VIDEO_SAA5249 is not set -# CONFIG_SOC_CAMERA is not set -# CONFIG_RADIO_ADAPTERS is not set -# CONFIG_DAB is not set +# CONFIG_AB3100_CORE is not set +# CONFIG_EZX_PCAP is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -917,6 +931,7 @@ CONFIG_RTC_DRV_PCF8563=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -962,12 +977,15 @@ CONFIG_RTC_DRV_PCF8563=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y # CONFIG_DNOTIFY is not set # CONFIG_INOTIFY is not set +CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set @@ -1021,6 +1039,12 @@ CONFIG_JFFS2_ZLIB=y # CONFIG_JFFS2_LZO is not set CONFIG_JFFS2_RTIME=y # CONFIG_JFFS2_RUBIN is not set +CONFIG_UBIFS_FS=y +# CONFIG_UBIFS_FS_XATTR is not set +# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set +CONFIG_UBIFS_FS_LZO=y +CONFIG_UBIFS_FS_ZLIB=y +# CONFIG_UBIFS_FS_DEBUG is not set # CONFIG_CRAMFS is not set # CONFIG_SQUASHFS is not set # CONFIG_VXFS_FS is not set @@ -1119,25 +1143,11 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y CONFIG_NOP_TRACER=y CONFIG_HAVE_FUNCTION_TRACER=y CONFIG_RING_BUFFER=y +CONFIG_EVENT_TRACING=y +CONFIG_CONTEXT_SWITCH_TRACER=y CONFIG_TRACING=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_IRQSOFF_TRACER is not set -# CONFIG_PREEMPT_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set -# CONFIG_FTRACE_STARTUP_TEST is not set +# CONFIG_FTRACE is not set # CONFIG_DYNAMIC_DEBUG is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y @@ -1151,16 +1161,104 @@ CONFIG_ARM_UNWIND=y # CONFIG_SECURITY is not set # CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set -# CONFIG_CRYPTO is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +# CONFIG_CRYPTO_FIPS is not set +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_ALGAPI2=y +# CONFIG_CRYPTO_MANAGER is not set +# CONFIG_CRYPTO_MANAGER2 is not set +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +# CONFIG_CRYPTO_CBC is not set +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +# CONFIG_CRYPTO_ECB is not set +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_PCBC is not set +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +# CONFIG_CRYPTO_MD5 is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_DES is not set +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +CONFIG_CRYPTO_DEFLATE=y +# CONFIG_CRYPTO_ZLIB is not set +CONFIG_CRYPTO_LZO=y + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set +CONFIG_CRYPTO_HW=y CONFIG_BINARY_PRINTF=y # # Library routines # CONFIG_BITREVERSE=y +CONFIG_RATIONAL=y CONFIG_GENERIC_FIND_LAST_BIT=y # CONFIG_CRC_CCITT is not set -# CONFIG_CRC16 is not set +CONFIG_CRC16=y # CONFIG_CRC_T10DIF is not set # CONFIG_CRC_ITU_T is not set CONFIG_CRC32=y @@ -1168,6 +1266,8 @@ CONFIG_CRC32=y # CONFIG_LIBCRC32C is not set CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=y +CONFIG_LZO_COMPRESS=y +CONFIG_LZO_DECOMPRESS=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y -- GitLab From 42469ff014812880d7324285d165841f4b1814e7 Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Fri, 24 Jul 2009 17:31:03 +0200 Subject: [PATCH 0396/1342] mx3 defconfig update - enable PCM043, MX31LILLY, ARMADILLO5X0 and MX35_3DS boards - enable MXC nand driver - enable UBI support - disable cs89x0 support which broke all boards which do not have this chip Signed-off-by: Sascha Hauer --- arch/arm/configs/mx3_defconfig | 151 ++++++++++++++++++++++----------- 1 file changed, 102 insertions(+), 49 deletions(-) diff --git a/arch/arm/configs/mx3_defconfig b/arch/arm/configs/mx3_defconfig index 20ada526f6d..a4f9a2a8149 100644 --- a/arch/arm/configs/mx3_defconfig +++ b/arch/arm/configs/mx3_defconfig @@ -1,15 +1,15 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc1 -# Wed Apr 8 11:06:37 2009 +# Linux kernel version: 2.6.31-rc4 +# Tue Jul 28 14:11:34 2009 # CONFIG_ARM=y +CONFIG_HAVE_PWM=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y CONFIG_GENERIC_GPIO=y CONFIG_GENERIC_TIME=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_MMU=y -# CONFIG_NO_IOPORT is not set CONFIG_GENERIC_HARDIRQS=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y @@ -18,14 +18,13 @@ CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_HARDIRQS_SW_RESEND=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_RWSEM_GENERIC_SPINLOCK=y -# CONFIG_ARCH_HAS_ILOG2_U32 is not set -# CONFIG_ARCH_HAS_ILOG2_U64 is not set CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_ARCH_MTD_XIP=y CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y CONFIG_VECTORS_BASE=0xffff0000 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -86,7 +85,12 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y + +# +# Performance Counters +# CONFIG_VM_EVENT_COUNTERS=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -97,6 +101,11 @@ CONFIG_HAVE_OPROFILE=y # CONFIG_KPROBES is not set CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y +CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set CONFIG_HAVE_GENERIC_DMA_COHERENT=y CONFIG_SLABINFO=y @@ -109,7 +118,7 @@ CONFIG_MODULE_FORCE_UNLOAD=y CONFIG_MODVERSIONS=y # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -136,13 +145,14 @@ CONFIG_FREEZER=y # CONFIG_ARCH_VERSATILE is not set # CONFIG_ARCH_AT91 is not set # CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_GEMINI is not set # CONFIG_ARCH_EBSA110 is not set # CONFIG_ARCH_EP93XX is not set -# CONFIG_ARCH_GEMINI is not set # CONFIG_ARCH_FOOTBRIDGE is not set +CONFIG_ARCH_MXC=y +# CONFIG_ARCH_STMP3XXX is not set # CONFIG_ARCH_NETX is not set # CONFIG_ARCH_H720X is not set -# CONFIG_ARCH_IMX is not set # CONFIG_ARCH_IOP13XX is not set # CONFIG_ARCH_IOP32X is not set # CONFIG_ARCH_IOP33X is not set @@ -151,25 +161,25 @@ CONFIG_FREEZER=y # CONFIG_ARCH_IXP4XX is not set # CONFIG_ARCH_L7200 is not set # CONFIG_ARCH_KIRKWOOD is not set -# CONFIG_ARCH_KS8695 is not set -# CONFIG_ARCH_NS9XXX is not set # CONFIG_ARCH_LOKI is not set # CONFIG_ARCH_MV78XX0 is not set -CONFIG_ARCH_MXC=y # CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_W90X900 is not set # CONFIG_ARCH_PNX4008 is not set # CONFIG_ARCH_PXA is not set -# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_MSM is not set # CONFIG_ARCH_RPC is not set # CONFIG_ARCH_SA1100 is not set # CONFIG_ARCH_S3C2410 is not set # CONFIG_ARCH_S3C64XX is not set # CONFIG_ARCH_SHARK is not set # CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_U300 is not set # CONFIG_ARCH_DAVINCI is not set # CONFIG_ARCH_OMAP is not set -# CONFIG_ARCH_MSM is not set -# CONFIG_ARCH_W90X900 is not set # # Freescale MXC Implementations @@ -178,6 +188,7 @@ CONFIG_ARCH_MXC=y # CONFIG_ARCH_MX2 is not set CONFIG_ARCH_MX3=y CONFIG_ARCH_MX31=y +CONFIG_ARCH_MX35=y # # MX3 platforms: @@ -185,12 +196,19 @@ CONFIG_ARCH_MX31=y CONFIG_MACH_MX31ADS=y CONFIG_MACH_MX31ADS_WM1133_EV1=y CONFIG_MACH_PCM037=y +CONFIG_MACH_PCM037_EET=y CONFIG_MACH_MX31LITE=y CONFIG_MACH_MX31_3DS=y CONFIG_MACH_MX31MOBOARD=y +CONFIG_MACH_MX31LILLY=y CONFIG_MACH_QONG=y +CONFIG_MACH_PCM043=y +CONFIG_MACH_ARMADILLO5X0=y +CONFIG_MACH_MX35_3DS=y CONFIG_MXC_IRQ_PRIOR=y CONFIG_MXC_PWM=y +CONFIG_ARCH_HAS_RNGA=y +CONFIG_ARCH_MXC_IOMUX_V3=y # # Processor Type @@ -218,6 +236,7 @@ CONFIG_ARM_THUMB=y # CONFIG_CPU_BPREDICT_DISABLE is not set CONFIG_OUTER_CACHE=y CONFIG_CACHE_L2X0=y +# CONFIG_ARM_ERRATA_411920 is not set CONFIG_COMMON_CLKDEV=y # @@ -242,7 +261,6 @@ CONFIG_PREEMPT=y CONFIG_HZ=100 CONFIG_AEABI=y CONFIG_OABI_COMPAT=y -CONFIG_ARCH_FLATMEM_HAS_HOLES=y # CONFIG_ARCH_SPARSEMEM_DEFAULT is not set # CONFIG_ARCH_SELECT_MEMORY_MODEL is not set # CONFIG_HIGHMEM is not set @@ -257,10 +275,11 @@ CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_ALIGNMENT_TRAP=y +# CONFIG_UACCESS_WITH_MEMCPY is not set # # Boot options @@ -362,6 +381,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -465,7 +485,16 @@ CONFIG_MTD_PHYSMAP=y # CONFIG_MTD_DOC2000 is not set # CONFIG_MTD_DOC2001 is not set # CONFIG_MTD_DOC2001PLUS is not set -# CONFIG_MTD_NAND is not set +CONFIG_MTD_NAND=y +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +# CONFIG_MTD_NAND_GPIO is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_DISKONCHIP is not set +# CONFIG_MTD_NAND_NANDSIM is not set +# CONFIG_MTD_NAND_PLATFORM is not set +CONFIG_MTD_NAND_MXC=y # CONFIG_MTD_ONENAND is not set # @@ -476,10 +505,30 @@ CONFIG_MTD_PHYSMAP=y # # UBI - Unsorted block images # -# CONFIG_MTD_UBI is not set +CONFIG_MTD_UBI=y +CONFIG_MTD_UBI_WL_THRESHOLD=4096 +CONFIG_MTD_UBI_BEB_RESERVE=1 +# CONFIG_MTD_UBI_GLUEBI is not set + +# +# UBI debugging options +# +# CONFIG_MTD_UBI_DEBUG is not set # CONFIG_PARPORT is not set # CONFIG_BLK_DEV is not set -# CONFIG_MISC_DEVICES is not set +CONFIG_MISC_DEVICES=y +# CONFIG_ICS932S401 is not set +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_ISL29003 is not set +# CONFIG_C2PORT is not set + +# +# EEPROM support +# +CONFIG_EEPROM_AT24=y +# CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set +# CONFIG_EEPROM_93CX6 is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -493,7 +542,6 @@ CONFIG_HAVE_IDE=y # CONFIG_ATA is not set # CONFIG_MD is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -528,7 +576,7 @@ CONFIG_MII=y # CONFIG_ETHOC is not set # CONFIG_SMC911X is not set CONFIG_SMSC911X=y -# CONFIG_DNET is not set +CONFIG_DNET=y # CONFIG_IBM_NEW_EMAC_ZMII is not set # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set @@ -537,8 +585,10 @@ CONFIG_SMSC911X=y # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set -CONFIG_CS89x0=y -CONFIG_CS89x0_NONISA_IRQ=y +# CONFIG_CS89x0 is not set +# CONFIG_KS8842 is not set +CONFIG_FEC=y +# CONFIG_FEC2 is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -609,6 +659,7 @@ CONFIG_I2C_HELPER_AUTO=y # # I2C system bus drivers (mostly embedded / system-on-chip) # +# CONFIG_I2C_DESIGNWARE is not set # CONFIG_I2C_GPIO is not set CONFIG_I2C_IMX=y # CONFIG_I2C_OCORES is not set @@ -633,7 +684,6 @@ CONFIG_I2C_IMX=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set @@ -669,6 +719,7 @@ CONFIG_W1=y # # CONFIG_W1_MASTER_DS2482 is not set CONFIG_W1_MASTER_MXC=y +# CONFIG_W1_MASTER_DS1WM is not set # CONFIG_W1_MASTER_GPIO is not set # @@ -703,6 +754,8 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_TPS65010 is not set # CONFIG_TWL4030_CORE is not set # CONFIG_MFD_TMIO is not set +# CONFIG_MFD_T7L66XB is not set +# CONFIG_MFD_TC6387XB is not set # CONFIG_MFD_TC6393XB is not set # CONFIG_PMIC_DA903X is not set # CONFIG_MFD_WM8400 is not set @@ -711,10 +764,8 @@ CONFIG_MFD_WM8350_CONFIG_MODE_0=y CONFIG_MFD_WM8352_CONFIG_MODE_0=y CONFIG_MFD_WM8350_I2C=y # CONFIG_MFD_PCF50633 is not set - -# -# Multimedia devices -# +# CONFIG_AB3100_CORE is not set +CONFIG_MEDIA_SUPPORT=y # # Multimedia core support @@ -758,8 +809,10 @@ CONFIG_SOC_CAMERA_MT9T031=y CONFIG_SOC_CAMERA_MT9V022=y CONFIG_SOC_CAMERA_TW9910=y # CONFIG_SOC_CAMERA_PLATFORM is not set -# CONFIG_SOC_CAMERA_OV772X is not set +CONFIG_SOC_CAMERA_OV772X=y +CONFIG_MX3_VIDEO=y CONFIG_VIDEO_MX3=y +# CONFIG_VIDEO_SH_MOBILE_CEU is not set # CONFIG_RADIO_ADAPTERS is not set # CONFIG_DAB is not set @@ -847,8 +900,11 @@ CONFIG_REGULATOR=y # CONFIG_REGULATOR_DEBUG is not set # CONFIG_REGULATOR_FIXED_VOLTAGE is not set # CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set +# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set # CONFIG_REGULATOR_BQ24022 is not set +# CONFIG_REGULATOR_MAX1586 is not set CONFIG_REGULATOR_WM8350=y +# CONFIG_REGULATOR_LP3971 is not set # CONFIG_UIO is not set # CONFIG_STAGING is not set @@ -861,10 +917,12 @@ CONFIG_REGULATOR_WM8350=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y # CONFIG_DNOTIFY is not set CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -921,6 +979,12 @@ CONFIG_JFFS2_ZLIB=y # CONFIG_JFFS2_LZO is not set CONFIG_JFFS2_RTIME=y # CONFIG_JFFS2_RUBIN is not set +CONFIG_UBIFS_FS=y +# CONFIG_UBIFS_FS_XATTR is not set +# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set +CONFIG_UBIFS_FS_LZO=y +CONFIG_UBIFS_FS_ZLIB=y +# CONFIG_UBIFS_FS_DEBUG is not set # CONFIG_CRAMFS is not set # CONFIG_SQUASHFS is not set # CONFIG_VXFS_FS is not set @@ -937,6 +1001,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -979,22 +1044,7 @@ CONFIG_FRAME_WARN=1024 CONFIG_SYSCTL_SYSCALL_CHECK=y CONFIG_HAVE_FUNCTION_TRACER=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_IRQSOFF_TRACER is not set -# CONFIG_PREEMPT_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y CONFIG_ARM_UNWIND=y @@ -1094,9 +1144,9 @@ CONFIG_CRYPTO_DES=y # # Compression # -# CONFIG_CRYPTO_DEFLATE is not set +CONFIG_CRYPTO_DEFLATE=y # CONFIG_CRYPTO_ZLIB is not set -# CONFIG_CRYPTO_LZO is not set +CONFIG_CRYPTO_LZO=y # # Random Number Generation @@ -1109,9 +1159,10 @@ CONFIG_CRYPTO_HW=y # Library routines # CONFIG_BITREVERSE=y +CONFIG_RATIONAL=y CONFIG_GENERIC_FIND_LAST_BIT=y # CONFIG_CRC_CCITT is not set -# CONFIG_CRC16 is not set +CONFIG_CRC16=y # CONFIG_CRC_T10DIF is not set # CONFIG_CRC_ITU_T is not set CONFIG_CRC32=y @@ -1119,6 +1170,8 @@ CONFIG_CRC32=y # CONFIG_LIBCRC32C is not set CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=y +CONFIG_LZO_COMPRESS=y +CONFIG_LZO_DECOMPRESS=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y -- GitLab From f25784b35f590c81d5fb8245a8cd45e1afb6f1b2 Mon Sep 17 00:00:00 2001 From: Yan Zheng Date: Tue, 28 Jul 2009 08:41:57 -0400 Subject: [PATCH 0397/1342] Btrfs: Fix async caching interaction with unmount - don't stop the caching thread until btrfs_commit_super return. - if caching is interrupted by umount, set last to (u64)-1. otherwise the un-scanned range of block group will be considered as free extent. Signed-off-by: Chris Mason --- fs/btrfs/disk-io.c | 3 +++ fs/btrfs/extent-tree.c | 4 +++- 2 files changed, 6 insertions(+), 1 deletion(-) diff --git a/fs/btrfs/disk-io.c b/fs/btrfs/disk-io.c index c658397c747..3a9b8875988 100644 --- a/fs/btrfs/disk-io.c +++ b/fs/btrfs/disk-io.c @@ -2317,6 +2317,9 @@ int close_ctree(struct btrfs_root *root) printk(KERN_ERR "btrfs: commit super ret %d\n", ret); } + fs_info->closing = 2; + smp_mb(); + if (fs_info->delalloc_bytes) { printk(KERN_INFO "btrfs: at unmount delalloc count %llu\n", (unsigned long long)fs_info->delalloc_bytes); diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c index 08188f1615d..fadf69a2764 100644 --- a/fs/btrfs/extent-tree.c +++ b/fs/btrfs/extent-tree.c @@ -288,8 +288,10 @@ again: while (1) { smp_mb(); - if (block_group->fs_info->closing) + if (block_group->fs_info->closing > 1) { + last = (u64)-1; break; + } leaf = path->nodes[0]; slot = path->slots[0]; -- GitLab From 1b54ab450b180eaeeb0eee6f0f64349246a22c14 Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Tue, 28 Jul 2009 16:31:39 +0200 Subject: [PATCH 0398/1342] hwmon: (smsc47m1) Differentiate between LPC47M233 and LPC47M292 The SMSC LPC47M233 and LPC47M292 chips have the same device ID but are not compatible. Signed-off-by: Jean Delvare Cc: Juerg Haefliger Acked-by: Hans de Goede --- drivers/hwmon/smsc47m1.c | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/drivers/hwmon/smsc47m1.c b/drivers/hwmon/smsc47m1.c index a92dbb97ee9..ba75bfcf14c 100644 --- a/drivers/hwmon/smsc47m1.c +++ b/drivers/hwmon/smsc47m1.c @@ -86,6 +86,7 @@ superio_exit(void) #define SUPERIO_REG_ACT 0x30 #define SUPERIO_REG_BASE 0x60 #define SUPERIO_REG_DEVID 0x20 +#define SUPERIO_REG_DEVREV 0x21 /* Logical device registers */ @@ -429,6 +430,9 @@ static int __init smsc47m1_find(unsigned short *addr, * The LPC47M292 (device id 0x6B) is somewhat compatible, but it * supports a 3rd fan, and the pin configuration registers are * unfortunately different. + * The LPC47M233 has the same device id (0x6B) but is not compatible. + * We check the high bit of the device revision register to + * differentiate them. */ switch (val) { case 0x51: @@ -448,6 +452,13 @@ static int __init smsc47m1_find(unsigned short *addr, sio_data->type = smsc47m1; break; case 0x6B: + if (superio_inb(SUPERIO_REG_DEVREV) & 0x80) { + pr_debug(DRVNAME ": " + "Found SMSC LPC47M233, unsupported\n"); + superio_exit(); + return -ENODEV; + } + pr_info(DRVNAME ": Found SMSC LPC47M292\n"); sio_data->type = smsc47m2; break; -- GitLab From 8d282497cbf8124d6814d51a74fb13d69531c669 Mon Sep 17 00:00:00 2001 From: Luca Tettamanti Date: Tue, 28 Jul 2009 16:31:39 +0200 Subject: [PATCH 0399/1342] hwmon: (asus_atk0110) Fix upper limit readings On newer Asus boards the "upper" limit of a sensor is encoded as delta from the "lower" limit. Fix the driver to correctly handle this case. Signed-off-by: Luca Tettamanti Tested-by: Alex Macfarlane Smith Signed-off-by: Jean Delvare --- drivers/hwmon/asus_atk0110.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/drivers/hwmon/asus_atk0110.c b/drivers/hwmon/asus_atk0110.c index bff0103610c..fe4fa29c921 100644 --- a/drivers/hwmon/asus_atk0110.c +++ b/drivers/hwmon/asus_atk0110.c @@ -593,7 +593,11 @@ static int atk_add_sensor(struct atk_data *data, union acpi_object *obj) sensor->data = data; sensor->id = flags->integer.value; sensor->limit1 = limit1->integer.value; - sensor->limit2 = limit2->integer.value; + if (data->old_interface) + sensor->limit2 = limit2->integer.value; + else + /* The upper limit is expressed as delta from lower limit */ + sensor->limit2 = sensor->limit1 + limit2->integer.value; snprintf(sensor->input_attr_name, ATTR_NAME_SIZE, "%s%d_input", base_name, start + *num); -- GitLab From 96f699ad09c8b3c55cd229506a9add0047838e3e Mon Sep 17 00:00:00 2001 From: Michele Jr De Candia Date: Tue, 28 Jul 2009 16:33:03 +0200 Subject: [PATCH 0400/1342] i2c/tsl2550: Fix lux value in dark environment I've tested TSL2550 driver and I've found a bug: when light is off, returned value from tsl2550_calculate_lux function is -1 when it should be 0 (sensor correctly read that light was off). I think the bug is that a zero c0 value (approximated value of ch0) is misinterpreted as an error. Signed-off-by: Michele Jr De Candia Acked-by: Rodolfo Giometti Signed-off-by: Jean Delvare --- drivers/i2c/chips/tsl2550.c | 17 ++++++++++------- 1 file changed, 10 insertions(+), 7 deletions(-) diff --git a/drivers/i2c/chips/tsl2550.c b/drivers/i2c/chips/tsl2550.c index 1a9cc135219..b96f3025e58 100644 --- a/drivers/i2c/chips/tsl2550.c +++ b/drivers/i2c/chips/tsl2550.c @@ -27,7 +27,7 @@ #include #define TSL2550_DRV_NAME "tsl2550" -#define DRIVER_VERSION "1.1.1" +#define DRIVER_VERSION "1.1.2" /* * Defines @@ -189,13 +189,16 @@ static int tsl2550_calculate_lux(u8 ch0, u8 ch1) u8 r = 128; /* Avoid division by 0 and count 1 cannot be greater than count 0 */ - if (c0 && (c1 <= c0)) - r = c1 * 128 / c0; + if (c1 <= c0) + if (c0) { + r = c1 * 128 / c0; + + /* Calculate LUX */ + lux = ((c0 - c1) * ratio_lut[r]) / 256; + } else + lux = 0; else - return -1; - - /* Calculate LUX */ - lux = ((c0 - c1) * ratio_lut[r]) / 256; + return -EAGAIN; /* LUX range check */ return lux > TSL2550_MAX_LUX ? TSL2550_MAX_LUX : lux; -- GitLab From 56ad1740d9a8dc271e71fee234be662638c64458 Mon Sep 17 00:00:00 2001 From: Jens Axboe Date: Tue, 28 Jul 2009 22:11:24 +0200 Subject: [PATCH 0401/1342] block: make the end_io functions be non-GPL exports Prior to the change for more sane end_io functions, we exported the helpers with the normal EXPORT_SYMBOL(). That got changed to _GPL() for the new interface. Revert that particular change, on the basis that this is basic functionality and doesn't dip into internal structures. If these exports can't be non-GPL, then we may as well make EXPORT_SYMBOL() imply GPL for everything. Signed-off-by: Jens Axboe --- block/blk-core.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/block/blk-core.c b/block/blk-core.c index a0c340d239b..e3299a77a0d 100644 --- a/block/blk-core.c +++ b/block/blk-core.c @@ -2136,7 +2136,7 @@ bool blk_end_request(struct request *rq, int error, unsigned int nr_bytes) { return blk_end_bidi_request(rq, error, nr_bytes, 0); } -EXPORT_SYMBOL_GPL(blk_end_request); +EXPORT_SYMBOL(blk_end_request); /** * blk_end_request_all - Helper function for drives to finish the request. @@ -2157,7 +2157,7 @@ void blk_end_request_all(struct request *rq, int error) pending = blk_end_bidi_request(rq, error, blk_rq_bytes(rq), bidi_bytes); BUG_ON(pending); } -EXPORT_SYMBOL_GPL(blk_end_request_all); +EXPORT_SYMBOL(blk_end_request_all); /** * blk_end_request_cur - Helper function to finish the current request chunk. @@ -2175,7 +2175,7 @@ bool blk_end_request_cur(struct request *rq, int error) { return blk_end_request(rq, error, blk_rq_cur_bytes(rq)); } -EXPORT_SYMBOL_GPL(blk_end_request_cur); +EXPORT_SYMBOL(blk_end_request_cur); /** * __blk_end_request - Helper function for drivers to complete the request. @@ -2194,7 +2194,7 @@ bool __blk_end_request(struct request *rq, int error, unsigned int nr_bytes) { return __blk_end_bidi_request(rq, error, nr_bytes, 0); } -EXPORT_SYMBOL_GPL(__blk_end_request); +EXPORT_SYMBOL(__blk_end_request); /** * __blk_end_request_all - Helper function for drives to finish the request. @@ -2215,7 +2215,7 @@ void __blk_end_request_all(struct request *rq, int error) pending = __blk_end_bidi_request(rq, error, blk_rq_bytes(rq), bidi_bytes); BUG_ON(pending); } -EXPORT_SYMBOL_GPL(__blk_end_request_all); +EXPORT_SYMBOL(__blk_end_request_all); /** * __blk_end_request_cur - Helper function to finish the current request chunk. @@ -2234,7 +2234,7 @@ bool __blk_end_request_cur(struct request *rq, int error) { return __blk_end_request(rq, error, blk_rq_cur_bytes(rq)); } -EXPORT_SYMBOL_GPL(__blk_end_request_cur); +EXPORT_SYMBOL(__blk_end_request_cur); void blk_rq_bio_prep(struct request_queue *q, struct request *rq, struct bio *bio) -- GitLab From 0f58b44582001c8bcdb75f36cf85ebbe5170e959 Mon Sep 17 00:00:00 2001 From: Peter Oberparleiter Date: Tue, 14 Jul 2009 17:56:15 +0200 Subject: [PATCH 0402/1342] sysfs: fix hardlink count on device_move Update directory hardlink count when moving kobjects to a new parent. Fixes the following problem which occurs when several devices are moved to the same parent and then unregistered: > ls -laF /sys/devices/css0/defunct/ > total 0 > drwxr-xr-x 4294967295 root root 0 2009-07-14 17:02 ./ > drwxr-xr-x 114 root root 0 2009-07-14 17:02 ../ > drwxr-xr-x 2 root root 0 2009-07-14 17:01 power/ > -rw-r--r-- 1 root root 4096 2009-07-14 17:01 uevent Signed-off-by: Peter Oberparleiter Cc: stable Signed-off-by: Greg Kroah-Hartman --- fs/sysfs/dir.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/fs/sysfs/dir.c b/fs/sysfs/dir.c index d88d0fac9fa..14f2d71ea3c 100644 --- a/fs/sysfs/dir.c +++ b/fs/sysfs/dir.c @@ -939,8 +939,10 @@ again: /* Remove from old parent's list and insert into new parent's list. */ sysfs_unlink_sibling(sd); sysfs_get(new_parent_sd); + drop_nlink(old_parent->d_inode); sysfs_put(sd->s_parent); sd->s_parent = new_parent_sd; + inc_nlink(new_parent->d_inode); sysfs_link_sibling(sd); out_unlock: -- GitLab From 3b4418c67a70278964b063b5e1f56dcb3d0a41f3 Mon Sep 17 00:00:00 2001 From: Ming Lei Date: Sat, 11 Jul 2009 11:11:10 +0800 Subject: [PATCH 0403/1342] driver core: firmware_class:fix memory leak of page pointers array The page pointers array is allocated in fw_realloc_buffer() called by firmware_data_write(), and should be freed in release function of firmware device. Signed-off-by: Ming Lei Reported-by: Catalin Marinas Acked-by: David Woodhouse Signed-off-by: Greg Kroah-Hartman --- drivers/base/firmware_class.c | 1 - 1 file changed, 1 deletion(-) diff --git a/drivers/base/firmware_class.c b/drivers/base/firmware_class.c index f285f441fab..7376367bcb8 100644 --- a/drivers/base/firmware_class.c +++ b/drivers/base/firmware_class.c @@ -180,7 +180,6 @@ static ssize_t firmware_loading_store(struct device *dev, goto err; } /* Pages will be freed by vfree() */ - fw_priv->pages = NULL; fw_priv->page_array_size = 0; fw_priv->nr_pages = 0; complete(&fw_priv->completion); -- GitLab From 4df7b3e0370ab6161ea2f258f51dd7c43bef2bda Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Wed, 15 Jul 2009 20:29:07 +0200 Subject: [PATCH 0404/1342] Dynamic debug: fix typo: -/-> The member was intended, not the local variable. Signed-off-by: Roel Kluin Cc: Jason Baron Cc: Greg Banks Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman --- lib/dynamic_debug.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/lib/dynamic_debug.c b/lib/dynamic_debug.c index 833139ce1e2..e22c148e4b7 100644 --- a/lib/dynamic_debug.c +++ b/lib/dynamic_debug.c @@ -164,7 +164,7 @@ static void ddebug_change(const struct ddebug_query *query, if (!newflags) dt->num_enabled--; - else if (!dp-flags) + else if (!dp->flags) dt->num_enabled++; dp->flags = newflags; if (newflags) { -- GitLab From 79f0313bfc67aa13abb931e8c12a1411f0161a68 Mon Sep 17 00:00:00 2001 From: Xiaotian Feng Date: Fri, 24 Jul 2009 17:31:41 +0800 Subject: [PATCH 0405/1342] driver core: sysdev: do not send KOBJ_ADD uevent if kobject_init_and_add fails If kobject_init_and_add fails, sysdev_register should not send KOBJ_ADD uevent to userspace. Signed-off-by: Xiaotian Feng Signed-off-by: Greg Kroah-Hartman --- drivers/base/sys.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/base/sys.c b/drivers/base/sys.c index 79a9ae5238a..0d903909af7 100644 --- a/drivers/base/sys.c +++ b/drivers/base/sys.c @@ -275,9 +275,9 @@ int sysdev_register(struct sys_device *sysdev) drv->add(sysdev); } mutex_unlock(&sysdev_drivers_lock); + kobject_uevent(&sysdev->kobj, KOBJ_ADD); } - kobject_uevent(&sysdev->kobj, KOBJ_ADD); return error; } -- GitLab From a39ea210ec8c8f6ed381f8dafbe755c57b8f30c3 Mon Sep 17 00:00:00 2001 From: Lucian Adrian Grijincu Date: Mon, 27 Jul 2009 09:06:42 -0700 Subject: [PATCH 0406/1342] driver core: documentation: make it clear that sysfs is optional The original text suggested that sysfs is mandatory and always compiled in the kernel. Signed-off-by: Lucian Adrian Grijincu Signed-off-by: Randy Dunlap Signed-off-by: Greg Kroah-Hartman --- Documentation/filesystems/sysfs.txt | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/Documentation/filesystems/sysfs.txt b/Documentation/filesystems/sysfs.txt index 7e81e37c0b1..b245d524d56 100644 --- a/Documentation/filesystems/sysfs.txt +++ b/Documentation/filesystems/sysfs.txt @@ -23,7 +23,8 @@ interface. Using sysfs ~~~~~~~~~~~ -sysfs is always compiled in. You can access it by doing: +sysfs is always compiled in if CONFIG_SYSFS is defined. You can access +it by doing: mount -t sysfs sysfs /sys -- GitLab From f3a756883ac028c536479e2eb283477fec80c828 Mon Sep 17 00:00:00 2001 From: Bill Pemberton Date: Tue, 14 Jul 2009 15:33:52 -0400 Subject: [PATCH 0407/1342] Staging: serqt_usb2: add missing calls to tty_kref_put() tty_port_tty_get() was called without a corresponding tty_kref_put() in qt_read_bulk_callback() and qt_close(). Signed-off-by: Bill Pemberton Signed-off-by: Greg Kroah-Hartman --- drivers/staging/serqt_usb2/serqt_usb2.c | 15 +++++++++------ 1 file changed, 9 insertions(+), 6 deletions(-) diff --git a/drivers/staging/serqt_usb2/serqt_usb2.c b/drivers/staging/serqt_usb2/serqt_usb2.c index a9bd4106beb..f9ff9c26678 100644 --- a/drivers/staging/serqt_usb2/serqt_usb2.c +++ b/drivers/staging/serqt_usb2/serqt_usb2.c @@ -360,18 +360,18 @@ static void qt_read_bulk_callback(struct urb *urb) if (port_paranoia_check(port, __func__) != 0) { dbg("%s - port_paranoia_check, exiting\n", __func__); qt_port->ReadBulkStopped = 1; - return; + goto exit; } if (!serial) { dbg("%s - bad serial pointer, exiting\n", __func__); - return; + goto exit; } if (qt_port->closePending == 1) { /* Were closing , stop reading */ dbg("%s - (qt_port->closepending == 1\n", __func__); qt_port->ReadBulkStopped = 1; - return; + goto exit; } /* @@ -381,7 +381,7 @@ static void qt_read_bulk_callback(struct urb *urb) */ if (qt_port->RxHolding == 1) { qt_port->ReadBulkStopped = 1; - return; + goto exit; } if (urb->status) { @@ -389,7 +389,7 @@ static void qt_read_bulk_callback(struct urb *urb) dbg("%s - nonzero read bulk status received: %d\n", __func__, urb->status); - return; + goto exit; } if (tty && RxCount) { @@ -463,6 +463,8 @@ static void qt_read_bulk_callback(struct urb *urb) } schedule_work(&port->work); +exit: + tty_kref_put(tty); } /* @@ -1041,7 +1043,7 @@ static void qt_block_until_empty(struct tty_struct *tty, } } -static void qt_close( struct usb_serial_port *port) +static void qt_close(struct usb_serial_port *port) { struct usb_serial *serial = port->serial; struct quatech_port *qt_port; @@ -1068,6 +1070,7 @@ static void qt_close( struct usb_serial_port *port) /* wait up to for transmitter to empty */ if (serial->dev) qt_block_until_empty(tty, qt_port); + tty_kref_put(tty); /* Close uart channel */ status = qt_close_channel(serial, index); -- GitLab From de8f8bd63334fe2014be7d9ab3a81ce9b96e5d19 Mon Sep 17 00:00:00 2001 From: Oliver Neukum Date: Mon, 13 Jul 2009 10:46:57 +0200 Subject: [PATCH 0408/1342] Staging: serqt_usb2: fix memory leak in error case a standard memory leak, as later allocations may fail even if prior allocations did not. Then the prior allocations must be undone. Signed-off-by: Oliver Neukum Signed-off-by: Greg Kroah-Hartman --- drivers/staging/serqt_usb2/serqt_usb2.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/staging/serqt_usb2/serqt_usb2.c b/drivers/staging/serqt_usb2/serqt_usb2.c index f9ff9c26678..0fdf8c6dc64 100644 --- a/drivers/staging/serqt_usb2/serqt_usb2.c +++ b/drivers/staging/serqt_usb2/serqt_usb2.c @@ -738,6 +738,11 @@ static int qt_startup(struct usb_serial *serial) if (!qt_port) { dbg("%s: kmalloc for quatech_port (%d) failed!.", __func__, i); + for(--i; i >= 0; i--) { + port = serial->port[i]; + kfree(usb_get_serial_port_data(port)); + usb_set_serial_port_data(port, NULL); + } return -ENOMEM; } spin_lock_init(&qt_port->lock); -- GitLab From a6a9f81ccc9f5c86ccc22bbed1960a57d0316e8b Mon Sep 17 00:00:00 2001 From: David Rientjes Date: Tue, 16 Jun 2009 16:42:53 -0700 Subject: [PATCH 0409/1342] Staging: android: lowmemorykiller.c: fix it for "oom: move oom_adj value from task_struct to mm_struct" I'm about to merge "oom: move oom_adj value from task_struct to mm_struct", and this fixup is needed to repair linux-next's drivers/staging/android/lowmemorykiller.c. Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman --- drivers/staging/android/lowmemorykiller.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) diff --git a/drivers/staging/android/lowmemorykiller.c b/drivers/staging/android/lowmemorykiller.c index fe72240f5a9..f934393f395 100644 --- a/drivers/staging/android/lowmemorykiller.c +++ b/drivers/staging/android/lowmemorykiller.c @@ -96,19 +96,21 @@ static int lowmem_shrink(int nr_to_scan, gfp_t gfp_mask) read_lock(&tasklist_lock); for_each_process(p) { + struct mm_struct *mm; int oom_adj; task_lock(p); - if (!p->mm) { + mm = p->mm; + if (!mm) { task_unlock(p); continue; } - oom_adj = p->oomkilladj; + oom_adj = mm->oom_adj; if (oom_adj < min_adj) { task_unlock(p); continue; } - tasksize = get_mm_rss(p->mm); + tasksize = get_mm_rss(mm); task_unlock(p); if (tasksize <= 0) continue; -- GitLab From 0bfc240575acb8769d0be78facedabd8e3d2c33a Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Sun, 19 Jul 2009 23:37:32 -0700 Subject: [PATCH 0410/1342] staging: remove aten2011 driver This driver is not needed, as the existing mos7840 driver works properly for this device. Thanks to Russell Lang for doing the work to figure this out. Cc: Russell Lang Signed-off-by: Greg Kroah-Hartman --- drivers/staging/Kconfig | 2 - drivers/staging/Makefile | 1 - drivers/staging/uc2322/Kconfig | 10 - drivers/staging/uc2322/Makefile | 1 - drivers/staging/uc2322/TODO | 7 - drivers/staging/uc2322/aten2011.c | 2430 ----------------------------- 6 files changed, 2451 deletions(-) delete mode 100644 drivers/staging/uc2322/Kconfig delete mode 100644 drivers/staging/uc2322/Makefile delete mode 100644 drivers/staging/uc2322/TODO delete mode 100644 drivers/staging/uc2322/aten2011.c diff --git a/drivers/staging/Kconfig b/drivers/staging/Kconfig index 348bf61a8fe..975ecddbce3 100644 --- a/drivers/staging/Kconfig +++ b/drivers/staging/Kconfig @@ -103,8 +103,6 @@ source "drivers/staging/pohmelfs/Kconfig" source "drivers/staging/stlc45xx/Kconfig" -source "drivers/staging/uc2322/Kconfig" - source "drivers/staging/b3dfg/Kconfig" source "drivers/staging/phison/Kconfig" diff --git a/drivers/staging/Makefile b/drivers/staging/Makefile index 8d61d7b4deb..2241ae1b21e 100644 --- a/drivers/staging/Makefile +++ b/drivers/staging/Makefile @@ -34,7 +34,6 @@ obj-$(CONFIG_ANDROID) += android/ obj-$(CONFIG_DST) += dst/ obj-$(CONFIG_POHMELFS) += pohmelfs/ obj-$(CONFIG_STLC45XX) += stlc45xx/ -obj-$(CONFIG_USB_SERIAL_ATEN2011) += uc2322/ obj-$(CONFIG_B3DFG) += b3dfg/ obj-$(CONFIG_IDE_PHISON) += phison/ obj-$(CONFIG_PLAN9AUTH) += p9auth/ diff --git a/drivers/staging/uc2322/Kconfig b/drivers/staging/uc2322/Kconfig deleted file mode 100644 index 2e0c6e79df2..00000000000 --- a/drivers/staging/uc2322/Kconfig +++ /dev/null @@ -1,10 +0,0 @@ -config USB_SERIAL_ATEN2011 - tristate "ATEN 2011 USB to serial device support" - depends on USB_SERIAL - default N - ---help--- - Say Y here if you want to use a ATEN 2011 dual port USB to serial - adapter. - - To compile this driver as a module, choose M here: the module will be - called aten2011. diff --git a/drivers/staging/uc2322/Makefile b/drivers/staging/uc2322/Makefile deleted file mode 100644 index 49c18d6e579..00000000000 --- a/drivers/staging/uc2322/Makefile +++ /dev/null @@ -1 +0,0 @@ -obj-$(CONFIG_USB_SERIAL_ATEN2011) += aten2011.o diff --git a/drivers/staging/uc2322/TODO b/drivers/staging/uc2322/TODO deleted file mode 100644 index c189a64c418..00000000000 --- a/drivers/staging/uc2322/TODO +++ /dev/null @@ -1,7 +0,0 @@ -TODO: - - checkpatch.pl cleanups - - remove dead and useless code (auditing the tty ioctls to - verify that they really are correct and needed.) - -Please send any patches to Greg Kroah-Hartman and -Russell Lang . diff --git a/drivers/staging/uc2322/aten2011.c b/drivers/staging/uc2322/aten2011.c deleted file mode 100644 index 39d0926d1a9..00000000000 --- a/drivers/staging/uc2322/aten2011.c +++ /dev/null @@ -1,2430 +0,0 @@ -/* - * Aten 2011 USB serial driver for 4 port devices - * - * Copyright (C) 2000 Inside Out Networks - * Copyright (C) 2001-2002, 2009 Greg Kroah-Hartman - * Copyright (C) 2009 Novell Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - - -#define ZLP_REG1 0x3A /* Zero_Flag_Reg1 58 */ -#define ZLP_REG2 0x3B /* Zero_Flag_Reg2 59 */ -#define ZLP_REG3 0x3C /* Zero_Flag_Reg3 60 */ -#define ZLP_REG4 0x3D /* Zero_Flag_Reg4 61 */ -#define ZLP_REG5 0x3E /* Zero_Flag_Reg5 62 */ - -/* Interrupt Rotinue Defines */ -#define SERIAL_IIR_RLS 0x06 -#define SERIAL_IIR_RDA 0x04 -#define SERIAL_IIR_CTI 0x0c -#define SERIAL_IIR_THR 0x02 -#define SERIAL_IIR_MS 0x00 - -/* Emulation of the bit mask on the LINE STATUS REGISTER. */ -#define SERIAL_LSR_DR 0x0001 -#define SERIAL_LSR_OE 0x0002 -#define SERIAL_LSR_PE 0x0004 -#define SERIAL_LSR_FE 0x0008 -#define SERIAL_LSR_BI 0x0010 -#define SERIAL_LSR_THRE 0x0020 -#define SERIAL_LSR_TEMT 0x0040 -#define SERIAL_LSR_FIFOERR 0x0080 - -/* MSR bit defines(place holders) */ -#define ATEN_MSR_DELTA_CTS 0x10 -#define ATEN_MSR_DELTA_DSR 0x20 -#define ATEN_MSR_DELTA_RI 0x40 -#define ATEN_MSR_DELTA_CD 0x80 - -/* Serial Port register Address */ -#define RECEIVE_BUFFER_REGISTER ((__u16)(0x00)) -#define TRANSMIT_HOLDING_REGISTER ((__u16)(0x00)) -#define INTERRUPT_ENABLE_REGISTER ((__u16)(0x01)) -#define INTERRUPT_IDENT_REGISTER ((__u16)(0x02)) -#define FIFO_CONTROL_REGISTER ((__u16)(0x02)) -#define LINE_CONTROL_REGISTER ((__u16)(0x03)) -#define MODEM_CONTROL_REGISTER ((__u16)(0x04)) -#define LINE_STATUS_REGISTER ((__u16)(0x05)) -#define MODEM_STATUS_REGISTER ((__u16)(0x06)) -#define SCRATCH_PAD_REGISTER ((__u16)(0x07)) -#define DIVISOR_LATCH_LSB ((__u16)(0x00)) -#define DIVISOR_LATCH_MSB ((__u16)(0x01)) - -#define SP1_REGISTER ((__u16)(0x00)) -#define CONTROL1_REGISTER ((__u16)(0x01)) -#define CLK_MULTI_REGISTER ((__u16)(0x02)) -#define CLK_START_VALUE_REGISTER ((__u16)(0x03)) -#define DCR1_REGISTER ((__u16)(0x04)) -#define GPIO_REGISTER ((__u16)(0x07)) - -#define SERIAL_LCR_DLAB ((__u16)(0x0080)) - -/* - * URB POOL related defines - */ -#define NUM_URBS 16 /* URB Count */ -#define URB_TRANSFER_BUFFER_SIZE 32 /* URB Size */ - -#define USB_VENDOR_ID_ATENINTL 0x0557 -#define ATENINTL_DEVICE_ID_2011 0x2011 -#define ATENINTL_DEVICE_ID_7820 0x7820 - -static struct usb_device_id id_table[] = { - { USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_2011) }, - { USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_7820) }, - { } /* terminating entry */ -}; -MODULE_DEVICE_TABLE(usb, id_table); - -/* This structure holds all of the local port information */ -struct ATENINTL_port { - int port_num; /*Actual port number in the device(1,2,etc)*/ - __u8 bulk_out_endpoint; /* the bulk out endpoint handle */ - unsigned char *bulk_out_buffer; /* buffer used for the bulk out endpoint */ - struct urb *write_urb; /* write URB for this port */ - __u8 bulk_in_endpoint; /* the bulk in endpoint handle */ - unsigned char *bulk_in_buffer; /* the buffer we use for the bulk in endpoint */ - struct urb *read_urb; /* read URB for this port */ - __u8 shadowLCR; /* last LCR value received */ - __u8 shadowMCR; /* last MCR value received */ - char open; - char chaseResponsePending; - wait_queue_head_t wait_chase; /* for handling sleeping while waiting for chase to finish */ - wait_queue_head_t wait_command; /* for handling sleeping while waiting for command to finish */ - struct async_icount icount; - struct usb_serial_port *port; /* loop back to the owner of this object */ - /*Offsets*/ - __u8 SpRegOffset; - __u8 ControlRegOffset; - __u8 DcrRegOffset; - /* for processing control URBS in interrupt context */ - struct urb *control_urb; - char *ctrl_buf; - int MsrLsr; - - struct urb *write_urb_pool[NUM_URBS]; - /* we pass a pointer to this as the arguement sent to cypress_set_termios old_termios */ - struct ktermios tmp_termios; /* stores the old termios settings */ - spinlock_t lock; /* private lock */ -}; - -/* This structure holds all of the individual serial device information */ -struct ATENINTL_serial { - __u8 interrupt_in_endpoint; /* the interrupt endpoint handle */ - unsigned char *interrupt_in_buffer; /* the buffer we use for the interrupt endpoint */ - struct urb *interrupt_read_urb; /* our interrupt urb */ - __u8 bulk_in_endpoint; /* the bulk in endpoint handle */ - unsigned char *bulk_in_buffer; /* the buffer we use for the bulk in endpoint */ - struct urb *read_urb; /* our bulk read urb */ - __u8 bulk_out_endpoint; /* the bulk out endpoint handle */ - struct usb_serial *serial; /* loop back to the owner of this object */ - int ATEN2011_spectrum_2or4ports; /* this says the number of ports in the device */ - /* Indicates about the no.of opened ports of an individual USB-serial adapater. */ - unsigned int NoOfOpenPorts; - /* a flag for Status endpoint polling */ - unsigned char status_polling_started; -}; - -static void ATEN2011_set_termios(struct tty_struct *tty, - struct usb_serial_port *port, - struct ktermios *old_termios); -static void ATEN2011_change_port_settings(struct tty_struct *tty, - struct ATENINTL_port *ATEN2011_port, - struct ktermios *old_termios); - -/************************************* - * Bit definitions for each register * - *************************************/ -#define LCR_BITS_5 0x00 /* 5 bits/char */ -#define LCR_BITS_6 0x01 /* 6 bits/char */ -#define LCR_BITS_7 0x02 /* 7 bits/char */ -#define LCR_BITS_8 0x03 /* 8 bits/char */ -#define LCR_BITS_MASK 0x03 /* Mask for bits/char field */ - -#define LCR_STOP_1 0x00 /* 1 stop bit */ -#define LCR_STOP_1_5 0x04 /* 1.5 stop bits (if 5 bits/char) */ -#define LCR_STOP_2 0x04 /* 2 stop bits (if 6-8 bits/char) */ -#define LCR_STOP_MASK 0x04 /* Mask for stop bits field */ - -#define LCR_PAR_NONE 0x00 /* No parity */ -#define LCR_PAR_ODD 0x08 /* Odd parity */ -#define LCR_PAR_EVEN 0x18 /* Even parity */ -#define LCR_PAR_MARK 0x28 /* Force parity bit to 1 */ -#define LCR_PAR_SPACE 0x38 /* Force parity bit to 0 */ -#define LCR_PAR_MASK 0x38 /* Mask for parity field */ - -#define LCR_SET_BREAK 0x40 /* Set Break condition */ -#define LCR_DL_ENABLE 0x80 /* Enable access to divisor latch */ - -#define MCR_DTR 0x01 /* Assert DTR */ -#define MCR_RTS 0x02 /* Assert RTS */ -#define MCR_OUT1 0x04 /* Loopback only: Sets state of RI */ -#define MCR_MASTER_IE 0x08 /* Enable interrupt outputs */ -#define MCR_LOOPBACK 0x10 /* Set internal (digital) loopback mode */ -#define MCR_XON_ANY 0x20 /* Enable any char to exit XOFF mode */ - -#define ATEN2011_MSR_CTS 0x10 /* Current state of CTS */ -#define ATEN2011_MSR_DSR 0x20 /* Current state of DSR */ -#define ATEN2011_MSR_RI 0x40 /* Current state of RI */ -#define ATEN2011_MSR_CD 0x80 /* Current state of CD */ - - -static int debug; - -/* - * Version Information - */ -#define DRIVER_VERSION "2.0" -#define DRIVER_DESC "ATENINTL 2011 USB Serial Adapter" - -/* - * Defines used for sending commands to port - */ - -#define ATEN_WDR_TIMEOUT (50) /* default urb timeout */ - -/* Requests */ -#define ATEN_RD_RTYPE 0xC0 -#define ATEN_WR_RTYPE 0x40 -#define ATEN_RDREQ 0x0D -#define ATEN_WRREQ 0x0E -#define ATEN_CTRL_TIMEOUT 500 -#define VENDOR_READ_LENGTH (0x01) - -/* set to 1 for RS485 mode and 0 for RS232 mode */ -/* FIXME make this somehow dynamic and not build time specific */ -static int RS485mode; - -static int set_reg_sync(struct usb_serial_port *port, __u16 reg, __u16 val) -{ - struct usb_device *dev = port->serial->dev; - val = val & 0x00ff; - - dbg("%s: is %x, value %x", __func__, reg, val); - - return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), ATEN_WRREQ, - ATEN_WR_RTYPE, val, reg, NULL, 0, - ATEN_WDR_TIMEOUT); -} - -static int get_reg_sync(struct usb_serial_port *port, __u16 reg, __u16 *val) -{ - struct usb_device *dev = port->serial->dev; - int ret; - - ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), ATEN_RDREQ, - ATEN_RD_RTYPE, 0, reg, val, VENDOR_READ_LENGTH, - ATEN_WDR_TIMEOUT); - dbg("%s: offset is %x, return val %x", __func__, reg, *val); - *val = (*val) & 0x00ff; - return ret; -} - -static int set_uart_reg(struct usb_serial_port *port, __u16 reg, __u16 val) -{ - struct usb_device *dev = port->serial->dev; - struct ATENINTL_serial *a_serial; - __u16 minor; - - a_serial = usb_get_serial_data(port->serial); - minor = port->serial->minor; - if (minor == SERIAL_TTY_NO_MINOR) - minor = 0; - val = val & 0x00ff; - - /* - * For the UART control registers, - * the application number need to be Or'ed - */ - if (a_serial->ATEN2011_spectrum_2or4ports == 4) - val |= (((__u16)port->number - minor) + 1) << 8; - else { - if (((__u16) port->number - minor) == 0) - val |= (((__u16)port->number - minor) + 1) << 8; - else - val |= (((__u16)port->number - minor) + 2) << 8; - } - dbg("%s: application number is %x", __func__, val); - - return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), ATEN_WRREQ, - ATEN_WR_RTYPE, val, reg, NULL, 0, - ATEN_WDR_TIMEOUT); -} - -static int get_uart_reg(struct usb_serial_port *port, __u16 reg, __u16 *val) -{ - struct usb_device *dev = port->serial->dev; - int ret = 0; - __u16 wval; - struct ATENINTL_serial *a_serial; - __u16 minor = port->serial->minor; - - a_serial = usb_get_serial_data(port->serial); - if (minor == SERIAL_TTY_NO_MINOR) - minor = 0; - - /* wval is same as application number */ - if (a_serial->ATEN2011_spectrum_2or4ports == 4) - wval = (((__u16)port->number - minor) + 1) << 8; - else { - if (((__u16) port->number - minor) == 0) - wval = (((__u16) port->number - minor) + 1) << 8; - else - wval = (((__u16) port->number - minor) + 2) << 8; - } - dbg("%s: application number is %x", __func__, wval); - ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), ATEN_RDREQ, - ATEN_RD_RTYPE, wval, reg, val, VENDOR_READ_LENGTH, - ATEN_WDR_TIMEOUT); - *val = (*val) & 0x00ff; - return ret; -} - -static int handle_newMsr(struct ATENINTL_port *port, __u8 newMsr) -{ - struct ATENINTL_port *ATEN2011_port; - struct async_icount *icount; - ATEN2011_port = port; - icount = &ATEN2011_port->icount; - if (newMsr & - (ATEN_MSR_DELTA_CTS | ATEN_MSR_DELTA_DSR | ATEN_MSR_DELTA_RI | - ATEN_MSR_DELTA_CD)) { - icount = &ATEN2011_port->icount; - - /* update input line counters */ - if (newMsr & ATEN_MSR_DELTA_CTS) - icount->cts++; - if (newMsr & ATEN_MSR_DELTA_DSR) - icount->dsr++; - if (newMsr & ATEN_MSR_DELTA_CD) - icount->dcd++; - if (newMsr & ATEN_MSR_DELTA_RI) - icount->rng++; - } - - return 0; -} - -static int handle_newLsr(struct ATENINTL_port *port, __u8 newLsr) -{ - struct async_icount *icount; - - dbg("%s - %02x", __func__, newLsr); - - if (newLsr & SERIAL_LSR_BI) { - /* - * Parity and Framing errors only count if they occur exclusive - * of a break being received. - */ - newLsr &= (__u8) (SERIAL_LSR_OE | SERIAL_LSR_BI); - } - - /* update input line counters */ - icount = &port->icount; - if (newLsr & SERIAL_LSR_BI) - icount->brk++; - if (newLsr & SERIAL_LSR_OE) - icount->overrun++; - if (newLsr & SERIAL_LSR_PE) - icount->parity++; - if (newLsr & SERIAL_LSR_FE) - icount->frame++; - - return 0; -} - -static void ATEN2011_control_callback(struct urb *urb) -{ - unsigned char *data; - struct ATENINTL_port *ATEN2011_port; - __u8 regval = 0x0; - - switch (urb->status) { - case 0: - /* success */ - break; - case -ECONNRESET: - case -ENOENT: - case -ESHUTDOWN: - /* this urb is terminated, clean up */ - dbg("%s - urb shutting down with status: %d", __func__, - urb->status); - return; - default: - dbg("%s - nonzero urb status received: %d", __func__, - urb->status); - goto exit; - } - - ATEN2011_port = (struct ATENINTL_port *)urb->context; - - dbg("%s urb buffer size is %d", __func__, urb->actual_length); - dbg("%s ATEN2011_port->MsrLsr is %d port %d", __func__, - ATEN2011_port->MsrLsr, ATEN2011_port->port_num); - data = urb->transfer_buffer; - regval = (__u8) data[0]; - dbg("%s data is %x", __func__, regval); - if (ATEN2011_port->MsrLsr == 0) - handle_newMsr(ATEN2011_port, regval); - else if (ATEN2011_port->MsrLsr == 1) - handle_newLsr(ATEN2011_port, regval); - -exit: - return; -} - -static int ATEN2011_get_reg(struct ATENINTL_port *ATEN, __u16 Wval, __u16 reg, - __u16 *val) -{ - struct usb_device *dev = ATEN->port->serial->dev; - struct usb_ctrlrequest *dr = NULL; - unsigned char *buffer = NULL; - int ret = 0; - buffer = (__u8 *) ATEN->ctrl_buf; - - dr = (void *)(buffer + 2); - dr->bRequestType = ATEN_RD_RTYPE; - dr->bRequest = ATEN_RDREQ; - dr->wValue = cpu_to_le16(Wval); - dr->wIndex = cpu_to_le16(reg); - dr->wLength = cpu_to_le16(2); - - usb_fill_control_urb(ATEN->control_urb, dev, usb_rcvctrlpipe(dev, 0), - (unsigned char *)dr, buffer, 2, - ATEN2011_control_callback, ATEN); - ATEN->control_urb->transfer_buffer_length = 2; - ret = usb_submit_urb(ATEN->control_urb, GFP_ATOMIC); - return ret; -} - -static void ATEN2011_interrupt_callback(struct urb *urb) -{ - int result; - int length; - struct ATENINTL_port *ATEN2011_port; - struct ATENINTL_serial *ATEN2011_serial; - struct usb_serial *serial; - __u16 Data; - unsigned char *data; - __u8 sp[5], st; - int i; - __u16 wval; - int minor; - - dbg("%s", " : Entering"); - - ATEN2011_serial = (struct ATENINTL_serial *)urb->context; - - switch (urb->status) { - case 0: - /* success */ - break; - case -ECONNRESET: - case -ENOENT: - case -ESHUTDOWN: - /* this urb is terminated, clean up */ - dbg("%s - urb shutting down with status: %d", __func__, - urb->status); - return; - default: - dbg("%s - nonzero urb status received: %d", __func__, - urb->status); - goto exit; - } - length = urb->actual_length; - data = urb->transfer_buffer; - - serial = ATEN2011_serial->serial; - - /* ATENINTL get 5 bytes - * Byte 1 IIR Port 1 (port.number is 0) - * Byte 2 IIR Port 2 (port.number is 1) - * Byte 3 IIR Port 3 (port.number is 2) - * Byte 4 IIR Port 4 (port.number is 3) - * Byte 5 FIFO status for both */ - - if (length && length > 5) { - dbg("%s", "Wrong data !!!"); - return; - } - - /* MATRIX */ - if (ATEN2011_serial->ATEN2011_spectrum_2or4ports == 4) { - sp[0] = (__u8) data[0]; - sp[1] = (__u8) data[1]; - sp[2] = (__u8) data[2]; - sp[3] = (__u8) data[3]; - st = (__u8) data[4]; - } else { - sp[0] = (__u8) data[0]; - sp[1] = (__u8) data[2]; - /* sp[2]=(__u8)data[2]; */ - /* sp[3]=(__u8)data[3]; */ - st = (__u8) data[4]; - - } - for (i = 0; i < serial->num_ports; i++) { - ATEN2011_port = usb_get_serial_port_data(serial->port[i]); - minor = serial->minor; - if (minor == SERIAL_TTY_NO_MINOR) - minor = 0; - if ((ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2) - && (i != 0)) - wval = - (((__u16) serial->port[i]->number - - (__u16) (minor)) + 2) << 8; - else - wval = - (((__u16) serial->port[i]->number - - (__u16) (minor)) + 1) << 8; - if (ATEN2011_port->open != 0) { - if (sp[i] & 0x01) { - dbg("SP%d No Interrupt !!!", i); - } else { - switch (sp[i] & 0x0f) { - case SERIAL_IIR_RLS: - dbg("Serial Port %d: Receiver status error or address bit detected in 9-bit mode", i); - ATEN2011_port->MsrLsr = 1; - ATEN2011_get_reg(ATEN2011_port, wval, - LINE_STATUS_REGISTER, - &Data); - break; - case SERIAL_IIR_MS: - dbg("Serial Port %d: Modem status change", i); - ATEN2011_port->MsrLsr = 0; - ATEN2011_get_reg(ATEN2011_port, wval, - MODEM_STATUS_REGISTER, - &Data); - break; - } - } - } - - } -exit: - if (ATEN2011_serial->status_polling_started == 0) - return; - - result = usb_submit_urb(urb, GFP_ATOMIC); - if (result) { - dev_err(&urb->dev->dev, - "%s - Error %d submitting interrupt urb\n", - __func__, result); - } - - return; -} - -static void ATEN2011_bulk_in_callback(struct urb *urb) -{ - int status; - unsigned char *data; - struct usb_serial *serial; - struct usb_serial_port *port; - struct ATENINTL_serial *ATEN2011_serial; - struct ATENINTL_port *ATEN2011_port; - struct tty_struct *tty; - - if (urb->status) { - dbg("nonzero read bulk status received: %d", urb->status); - return; - } - - ATEN2011_port = (struct ATENINTL_port *)urb->context; - - port = (struct usb_serial_port *)ATEN2011_port->port; - serial = port->serial; - - dbg("%s", "Entering..."); - - data = urb->transfer_buffer; - ATEN2011_serial = usb_get_serial_data(serial); - - if (urb->actual_length) { - tty = tty_port_tty_get(&ATEN2011_port->port->port); - if (tty) { - tty_buffer_request_room(tty, urb->actual_length); - tty_insert_flip_string(tty, data, urb->actual_length); - tty_flip_buffer_push(tty); - tty_kref_put(tty); - } - - ATEN2011_port->icount.rx += urb->actual_length; - dbg("ATEN2011_port->icount.rx is %d:", - ATEN2011_port->icount.rx); - } - - if (!ATEN2011_port->read_urb) { - dbg("%s", "URB KILLED !!!"); - return; - } - - if (ATEN2011_port->read_urb->status != -EINPROGRESS) { - ATEN2011_port->read_urb->dev = serial->dev; - - status = usb_submit_urb(ATEN2011_port->read_urb, GFP_ATOMIC); - if (status) - dbg("usb_submit_urb(read bulk) failed, status = %d", status); - } -} - -static void ATEN2011_bulk_out_data_callback(struct urb *urb) -{ - struct ATENINTL_port *ATEN2011_port; - struct tty_struct *tty; - - if (urb->status) { - dbg("nonzero write bulk status received:%d", urb->status); - return; - } - - ATEN2011_port = (struct ATENINTL_port *)urb->context; - - dbg("%s", "Entering ........."); - - tty = tty_port_tty_get(&ATEN2011_port->port->port); - - if (tty && ATEN2011_port->open) - /* tell the tty driver that something has changed */ - tty_wakeup(tty); - - /* schedule_work(&ATEN2011_port->port->work); */ - tty_kref_put(tty); - -} - -#ifdef ATENSerialProbe -static int ATEN2011_serial_probe(struct usb_serial *serial, - const struct usb_device_id *id) -{ - - /*need to implement the mode_reg reading and updating\ - structures usb_serial_ device_type\ - (i.e num_ports, num_bulkin,bulkout etc) */ - /* Also we can update the changes attach */ - return 1; -} -#endif - -static int ATEN2011_open(struct tty_struct *tty, struct usb_serial_port *port, - struct file *filp) -{ - int response; - int j; - struct usb_serial *serial; - struct urb *urb; - __u16 Data; - int status; - struct ATENINTL_serial *ATEN2011_serial; - struct ATENINTL_port *ATEN2011_port; - struct ktermios tmp_termios; - int minor; - - serial = port->serial; - - ATEN2011_port = usb_get_serial_port_data(port); - - if (ATEN2011_port == NULL) - return -ENODEV; - - ATEN2011_serial = usb_get_serial_data(serial); - if (ATEN2011_serial == NULL) - return -ENODEV; - - /* increment the number of opened ports counter here */ - ATEN2011_serial->NoOfOpenPorts++; - - usb_clear_halt(serial->dev, port->write_urb->pipe); - usb_clear_halt(serial->dev, port->read_urb->pipe); - - /* Initialising the write urb pool */ - for (j = 0; j < NUM_URBS; ++j) { - urb = usb_alloc_urb(0, GFP_ATOMIC); - ATEN2011_port->write_urb_pool[j] = urb; - - if (urb == NULL) { - err("No more urbs???"); - continue; - } - - urb->transfer_buffer = NULL; - urb->transfer_buffer = - kmalloc(URB_TRANSFER_BUFFER_SIZE, GFP_KERNEL); - if (!urb->transfer_buffer) { - err("%s-out of memory for urb buffers.", __func__); - continue; - } - } - -/***************************************************************************** - * Initialize ATEN2011 -- Write Init values to corresponding Registers - * - * Register Index - * 1 : IER - * 2 : FCR - * 3 : LCR - * 4 : MCR - * - * 0x08 : SP1/2 Control Reg - *****************************************************************************/ - -/* NEED to check the fallowing Block */ - - Data = 0x0; - status = get_reg_sync(port, ATEN2011_port->SpRegOffset, &Data); - if (status < 0) { - dbg("Reading Spreg failed"); - return -1; - } - Data |= 0x80; - status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data); - if (status < 0) { - dbg("writing Spreg failed"); - return -1; - } - - Data &= ~0x80; - status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data); - if (status < 0) { - dbg("writing Spreg failed"); - return -1; - } - -/* End of block to be checked */ -/**************************CHECK***************************/ - - if (RS485mode == 0) - Data = 0xC0; - else - Data = 0x00; - status = set_uart_reg(port, SCRATCH_PAD_REGISTER, Data); - if (status < 0) { - dbg("Writing SCRATCH_PAD_REGISTER failed status-0x%x", status); - return -1; - } else - dbg("SCRATCH_PAD_REGISTER Writing success status%d", status); - -/**************************CHECK***************************/ - - Data = 0x0; - status = get_reg_sync(port, ATEN2011_port->ControlRegOffset, &Data); - if (status < 0) { - dbg("Reading Controlreg failed"); - return -1; - } - Data |= 0x08; /* Driver done bit */ - Data |= 0x20; /* rx_disable */ - status = 0; - status = - set_reg_sync(port, ATEN2011_port->ControlRegOffset, Data); - if (status < 0) { - dbg("writing Controlreg failed"); - return -1; - } - /* - * do register settings here - * Set all regs to the device default values. - * First Disable all interrupts. - */ - - Data = 0x00; - status = set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data); - if (status < 0) { - dbg("disableing interrupts failed"); - return -1; - } - /* Set FIFO_CONTROL_REGISTER to the default value */ - Data = 0x00; - status = set_uart_reg(port, FIFO_CONTROL_REGISTER, Data); - if (status < 0) { - dbg("Writing FIFO_CONTROL_REGISTER failed"); - return -1; - } - - Data = 0xcf; /* chk */ - status = set_uart_reg(port, FIFO_CONTROL_REGISTER, Data); - if (status < 0) { - dbg("Writing FIFO_CONTROL_REGISTER failed"); - return -1; - } - - Data = 0x03; /* LCR_BITS_8 */ - status = set_uart_reg(port, LINE_CONTROL_REGISTER, Data); - ATEN2011_port->shadowLCR = Data; - - Data = 0x0b; /* MCR_DTR|MCR_RTS|MCR_MASTER_IE */ - status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); - ATEN2011_port->shadowMCR = Data; - -#ifdef Check - Data = 0x00; - status = get_uart_reg(port, LINE_CONTROL_REGISTER, &Data); - ATEN2011_port->shadowLCR = Data; - - Data |= SERIAL_LCR_DLAB; /* data latch enable in LCR 0x80 */ - status = set_uart_reg(port, LINE_CONTROL_REGISTER, Data); - - Data = 0x0c; - status = set_uart_reg(port, DIVISOR_LATCH_LSB, Data); - - Data = 0x0; - status = set_uart_reg(port, DIVISOR_LATCH_MSB, Data); - - Data = 0x00; - status = get_uart_reg(port, LINE_CONTROL_REGISTER, &Data); - -/* Data = ATEN2011_port->shadowLCR; */ /* data latch disable */ - Data = Data & ~SERIAL_LCR_DLAB; - status = set_uart_reg(port, LINE_CONTROL_REGISTER, Data); - ATEN2011_port->shadowLCR = Data; -#endif - /* clearing Bulkin and Bulkout Fifo */ - Data = 0x0; - status = get_reg_sync(port, ATEN2011_port->SpRegOffset, &Data); - - Data = Data | 0x0c; - status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data); - - Data = Data & ~0x0c; - status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data); - /* Finally enable all interrupts */ - Data = 0x0; - Data = 0x0c; - status = set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data); - - /* clearing rx_disable */ - Data = 0x0; - status = get_reg_sync(port, ATEN2011_port->ControlRegOffset, &Data); - Data = Data & ~0x20; - status = set_reg_sync(port, ATEN2011_port->ControlRegOffset, Data); - - /* rx_negate */ - Data = 0x0; - status = get_reg_sync(port, ATEN2011_port->ControlRegOffset, &Data); - Data = Data | 0x10; - status = 0; - status = set_reg_sync(port, ATEN2011_port->ControlRegOffset, Data); - - /* - * Check to see if we've set up our endpoint info yet - * (can't set it up in ATEN2011_startup as the structures - * were not set up at that time.) - */ - if (ATEN2011_serial->NoOfOpenPorts == 1) { - /* start the status polling here */ - ATEN2011_serial->status_polling_started = 1; - /* If not yet set, Set here */ - ATEN2011_serial->interrupt_in_buffer = - serial->port[0]->interrupt_in_buffer; - ATEN2011_serial->interrupt_in_endpoint = - serial->port[0]->interrupt_in_endpointAddress; - ATEN2011_serial->interrupt_read_urb = - serial->port[0]->interrupt_in_urb; - - /* set up interrupt urb */ - usb_fill_int_urb(ATEN2011_serial->interrupt_read_urb, - serial->dev, - usb_rcvintpipe(serial->dev, - ATEN2011_serial-> - interrupt_in_endpoint), - ATEN2011_serial->interrupt_in_buffer, - ATEN2011_serial->interrupt_read_urb-> - transfer_buffer_length, - ATEN2011_interrupt_callback, ATEN2011_serial, - ATEN2011_serial->interrupt_read_urb->interval); - - /* start interrupt read for ATEN2011 * - * will continue as long as ATEN2011 is connected */ - - response = - usb_submit_urb(ATEN2011_serial->interrupt_read_urb, - GFP_KERNEL); - if (response) { - dbg("%s - Error %d submitting interrupt urb", - __func__, response); - } - - } - - /* - * See if we've set up our endpoint info yet - * (can't set it up in ATEN2011_startup as the - * structures were not set up at that time.) - */ - - dbg("port number is %d", port->number); - dbg("serial number is %d", port->serial->minor); - dbg("Bulkin endpoint is %d", port->bulk_in_endpointAddress); - dbg("BulkOut endpoint is %d", port->bulk_out_endpointAddress); - dbg("Interrupt endpoint is %d", - port->interrupt_in_endpointAddress); - dbg("port's number in the device is %d", ATEN2011_port->port_num); - ATEN2011_port->bulk_in_buffer = port->bulk_in_buffer; - ATEN2011_port->bulk_in_endpoint = port->bulk_in_endpointAddress; - ATEN2011_port->read_urb = port->read_urb; - ATEN2011_port->bulk_out_endpoint = port->bulk_out_endpointAddress; - - minor = port->serial->minor; - if (minor == SERIAL_TTY_NO_MINOR) - minor = 0; - - /* set up our bulk in urb */ - if ((ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2) - && (((__u16) port->number - (__u16) (minor)) != 0)) { - usb_fill_bulk_urb(ATEN2011_port->read_urb, serial->dev, - usb_rcvbulkpipe(serial->dev, - (port-> - bulk_in_endpointAddress + - 2)), port->bulk_in_buffer, - ATEN2011_port->read_urb-> - transfer_buffer_length, - ATEN2011_bulk_in_callback, ATEN2011_port); - } else - usb_fill_bulk_urb(ATEN2011_port->read_urb, - serial->dev, - usb_rcvbulkpipe(serial->dev, - port-> - bulk_in_endpointAddress), - port->bulk_in_buffer, - ATEN2011_port->read_urb-> - transfer_buffer_length, - ATEN2011_bulk_in_callback, ATEN2011_port); - - dbg("ATEN2011_open: bulkin endpoint is %d", - port->bulk_in_endpointAddress); - response = usb_submit_urb(ATEN2011_port->read_urb, GFP_KERNEL); - if (response) { - err("%s - Error %d submitting control urb", __func__, - response); - } - - /* initialize our wait queues */ - init_waitqueue_head(&ATEN2011_port->wait_chase); - init_waitqueue_head(&ATEN2011_port->wait_command); - - /* initialize our icount structure */ - memset(&(ATEN2011_port->icount), 0x00, sizeof(ATEN2011_port->icount)); - - /* initialize our port settings */ - ATEN2011_port->shadowMCR = MCR_MASTER_IE; /* Must set to enable ints! */ - ATEN2011_port->chaseResponsePending = 0; - /* send a open port command */ - ATEN2011_port->open = 1; - /* ATEN2011_change_port_settings(ATEN2011_port,old_termios); */ - /* Setup termios */ - ATEN2011_set_termios(tty, port, &tmp_termios); - ATEN2011_port->icount.tx = 0; - ATEN2011_port->icount.rx = 0; - - dbg("usb_serial serial:%x ATEN2011_port:%x\nATEN2011_serial:%x usb_serial_port port:%x", - (unsigned int)serial, (unsigned int)ATEN2011_port, - (unsigned int)ATEN2011_serial, (unsigned int)port); - - return 0; - -} - -static int ATEN2011_chars_in_buffer(struct tty_struct *tty) -{ - struct usb_serial_port *port = tty->driver_data; - int i; - int chars = 0; - struct ATENINTL_port *ATEN2011_port; - - /* dbg("%s"," ATEN2011_chars_in_buffer:entering ..........."); */ - - ATEN2011_port = usb_get_serial_port_data(port); - if (ATEN2011_port == NULL) { - dbg("%s", "ATEN2011_break:leaving ..........."); - return -1; - } - - for (i = 0; i < NUM_URBS; ++i) - if (ATEN2011_port->write_urb_pool[i]->status == -EINPROGRESS) - chars += URB_TRANSFER_BUFFER_SIZE; - - dbg("%s - returns %d", __func__, chars); - return chars; - -} - -static void ATEN2011_block_until_tx_empty(struct tty_struct *tty, - struct ATENINTL_port *ATEN2011_port) -{ - int timeout = HZ / 10; - int wait = 30; - int count; - - while (1) { - count = ATEN2011_chars_in_buffer(tty); - - /* Check for Buffer status */ - if (count <= 0) - return; - - /* Block the thread for a while */ - interruptible_sleep_on_timeout(&ATEN2011_port->wait_chase, - timeout); - - /* No activity.. count down section */ - wait--; - if (wait == 0) { - dbg("%s - TIMEOUT", __func__); - return; - } else { - /* Reset timout value back to seconds */ - wait = 30; - } - } -} - -static void ATEN2011_close(struct tty_struct *tty, struct usb_serial_port *port, - struct file *filp) -{ - struct usb_serial *serial; - struct ATENINTL_serial *ATEN2011_serial; - struct ATENINTL_port *ATEN2011_port; - int no_urbs; - __u16 Data; - - dbg("%s", "ATEN2011_close:entering..."); - serial = port->serial; - - /* take the Adpater and port's private data */ - ATEN2011_serial = usb_get_serial_data(serial); - ATEN2011_port = usb_get_serial_port_data(port); - if ((ATEN2011_serial == NULL) || (ATEN2011_port == NULL)) - return; - - if (serial->dev) { - /* flush and block(wait) until tx is empty */ - ATEN2011_block_until_tx_empty(tty, ATEN2011_port); - } - /* kill the ports URB's */ - for (no_urbs = 0; no_urbs < NUM_URBS; no_urbs++) - usb_kill_urb(ATEN2011_port->write_urb_pool[no_urbs]); - /* Freeing Write URBs */ - for (no_urbs = 0; no_urbs < NUM_URBS; ++no_urbs) { - kfree(ATEN2011_port->write_urb_pool[no_urbs]->transfer_buffer); - usb_free_urb(ATEN2011_port->write_urb_pool[no_urbs]); - } - /* While closing port, shutdown all bulk read, write * - * and interrupt read if they exists */ - if (serial->dev) { - if (ATEN2011_port->write_urb) { - dbg("%s", "Shutdown bulk write"); - usb_kill_urb(ATEN2011_port->write_urb); - } - if (ATEN2011_port->read_urb) { - dbg("%s", "Shutdown bulk read"); - usb_kill_urb(ATEN2011_port->read_urb); - } - if ((&ATEN2011_port->control_urb)) { - dbg("%s", "Shutdown control read"); - /* usb_kill_urb (ATEN2011_port->control_urb); */ - - } - } - /* if(ATEN2011_port->ctrl_buf != NULL) */ - /* kfree(ATEN2011_port->ctrl_buf); */ - /* decrement the no.of open ports counter of an individual USB-serial adapter. */ - ATEN2011_serial->NoOfOpenPorts--; - dbg("NoOfOpenPorts in close%d:in port%d", - ATEN2011_serial->NoOfOpenPorts, port->number); - if (ATEN2011_serial->NoOfOpenPorts == 0) { - /* stop the stus polling here */ - ATEN2011_serial->status_polling_started = 0; - if (ATEN2011_serial->interrupt_read_urb) { - dbg("%s", "Shutdown interrupt_read_urb"); - /* ATEN2011_serial->interrupt_in_buffer=NULL; */ - /* usb_kill_urb (ATEN2011_serial->interrupt_read_urb); */ - } - } - if (ATEN2011_port->write_urb) { - /* if this urb had a transfer buffer already (old tx) free it */ - kfree(ATEN2011_port->write_urb->transfer_buffer); - usb_free_urb(ATEN2011_port->write_urb); - } - - /* clear the MCR & IER */ - Data = 0x00; - set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); - Data = 0x00; - set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data); - - ATEN2011_port->open = 0; - dbg("%s", "Leaving ............"); - -} - -static void ATEN2011_block_until_chase_response(struct tty_struct *tty, - struct ATENINTL_port - *ATEN2011_port) -{ - int timeout = 1 * HZ; - int wait = 10; - int count; - - while (1) { - count = ATEN2011_chars_in_buffer(tty); - - /* Check for Buffer status */ - if (count <= 0) { - ATEN2011_port->chaseResponsePending = 0; - return; - } - - /* Block the thread for a while */ - interruptible_sleep_on_timeout(&ATEN2011_port->wait_chase, - timeout); - /* No activity.. count down section */ - wait--; - if (wait == 0) { - dbg("%s - TIMEOUT", __func__); - return; - } else { - /* Reset timout value back to seconds */ - wait = 10; - } - } - -} - -static void ATEN2011_break(struct tty_struct *tty, int break_state) -{ - struct usb_serial_port *port = tty->driver_data; - unsigned char data; - struct usb_serial *serial; - struct ATENINTL_serial *ATEN2011_serial; - struct ATENINTL_port *ATEN2011_port; - - dbg("%s", "Entering ..........."); - dbg("ATEN2011_break: Start"); - - serial = port->serial; - - ATEN2011_serial = usb_get_serial_data(serial); - ATEN2011_port = usb_get_serial_port_data(port); - - if ((ATEN2011_serial == NULL) || (ATEN2011_port == NULL)) - return; - - /* flush and chase */ - ATEN2011_port->chaseResponsePending = 1; - - if (serial->dev) { - /* flush and block until tx is empty */ - ATEN2011_block_until_chase_response(tty, ATEN2011_port); - } - - if (break_state == -1) - data = ATEN2011_port->shadowLCR | LCR_SET_BREAK; - else - data = ATEN2011_port->shadowLCR & ~LCR_SET_BREAK; - - ATEN2011_port->shadowLCR = data; - dbg("ATEN2011_break ATEN2011_port->shadowLCR is %x", - ATEN2011_port->shadowLCR); - set_uart_reg(port, LINE_CONTROL_REGISTER, ATEN2011_port->shadowLCR); - - return; -} - -static int ATEN2011_write_room(struct tty_struct *tty) -{ - struct usb_serial_port *port = tty->driver_data; - int i; - int room = 0; - struct ATENINTL_port *ATEN2011_port; - - ATEN2011_port = usb_get_serial_port_data(port); - if (ATEN2011_port == NULL) { - dbg("%s", "ATEN2011_break:leaving ..........."); - return -1; - } - - for (i = 0; i < NUM_URBS; ++i) - if (ATEN2011_port->write_urb_pool[i]->status != -EINPROGRESS) - room += URB_TRANSFER_BUFFER_SIZE; - - dbg("%s - returns %d", __func__, room); - return room; - -} - -static int ATEN2011_write(struct tty_struct *tty, struct usb_serial_port *port, - const unsigned char *data, int count) -{ - int status; - int i; - int bytes_sent = 0; - int transfer_size; - int minor; - - struct ATENINTL_port *ATEN2011_port; - struct usb_serial *serial; - struct ATENINTL_serial *ATEN2011_serial; - struct urb *urb; - const unsigned char *current_position = data; - unsigned char *data1; - dbg("%s", "entering ..........."); - - serial = port->serial; - - ATEN2011_port = usb_get_serial_port_data(port); - if (ATEN2011_port == NULL) { - dbg("%s", "ATEN2011_port is NULL"); - return -1; - } - - ATEN2011_serial = usb_get_serial_data(serial); - if (ATEN2011_serial == NULL) { - dbg("%s", "ATEN2011_serial is NULL"); - return -1; - } - - /* try to find a free urb in the list */ - urb = NULL; - - for (i = 0; i < NUM_URBS; ++i) { - if (ATEN2011_port->write_urb_pool[i]->status != -EINPROGRESS) { - urb = ATEN2011_port->write_urb_pool[i]; - dbg("URB:%d", i); - break; - } - } - - if (urb == NULL) { - dbg("%s - no more free urbs", __func__); - goto exit; - } - - if (urb->transfer_buffer == NULL) { - urb->transfer_buffer = - kmalloc(URB_TRANSFER_BUFFER_SIZE, GFP_KERNEL); - - if (urb->transfer_buffer == NULL) { - err("%s no more kernel memory...", __func__); - goto exit; - } - } - transfer_size = min(count, URB_TRANSFER_BUFFER_SIZE); - - memcpy(urb->transfer_buffer, current_position, transfer_size); - /* usb_serial_debug_data (__FILE__, __func__, transfer_size, urb->transfer_buffer); */ - - /* fill urb with data and submit */ - minor = port->serial->minor; - if (minor == SERIAL_TTY_NO_MINOR) - minor = 0; - if ((ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2) - && (((__u16) port->number - (__u16) (minor)) != 0)) { - usb_fill_bulk_urb(urb, ATEN2011_serial->serial->dev, - usb_sndbulkpipe(ATEN2011_serial->serial->dev, - (port-> - bulk_out_endpointAddress) + - 2), urb->transfer_buffer, - transfer_size, - ATEN2011_bulk_out_data_callback, - ATEN2011_port); - } else - - usb_fill_bulk_urb(urb, - ATEN2011_serial->serial->dev, - usb_sndbulkpipe(ATEN2011_serial->serial->dev, - port-> - bulk_out_endpointAddress), - urb->transfer_buffer, transfer_size, - ATEN2011_bulk_out_data_callback, - ATEN2011_port); - - data1 = urb->transfer_buffer; - dbg("bulkout endpoint is %d", port->bulk_out_endpointAddress); - /* for(i=0;i < urb->actual_length;i++) */ - /* dbg("Data is %c ",data1[i]); */ - - /* send it down the pipe */ - status = usb_submit_urb(urb, GFP_ATOMIC); - - if (status) { - err("%s - usb_submit_urb(write bulk) failed with status = %d", - __func__, status); - bytes_sent = status; - goto exit; - } - bytes_sent = transfer_size; - ATEN2011_port->icount.tx += transfer_size; - dbg("ATEN2011_port->icount.tx is %d:", ATEN2011_port->icount.tx); - -exit: - return bytes_sent; -} - -static void ATEN2011_throttle(struct tty_struct *tty) -{ - struct usb_serial_port *port = tty->driver_data; - struct ATENINTL_port *ATEN2011_port; - int status; - - dbg("- port %d", port->number); - - ATEN2011_port = usb_get_serial_port_data(port); - - if (ATEN2011_port == NULL) - return; - - if (!ATEN2011_port->open) { - dbg("%s", "port not opened"); - return; - } - - dbg("%s", "Entering .......... "); - - if (!tty) { - dbg("%s - no tty available", __func__); - return; - } - - /* if we are implementing XON/XOFF, send the stop character */ - if (I_IXOFF(tty)) { - unsigned char stop_char = STOP_CHAR(tty); - status = ATEN2011_write(tty, port, &stop_char, 1); - if (status <= 0) - return; - } - - /* if we are implementing RTS/CTS, toggle that line */ - if (tty->termios->c_cflag & CRTSCTS) { - ATEN2011_port->shadowMCR &= ~MCR_RTS; - status = set_uart_reg(port, MODEM_CONTROL_REGISTER, - ATEN2011_port->shadowMCR); - if (status < 0) - return; - } - - return; -} - -static void ATEN2011_unthrottle(struct tty_struct *tty) -{ - struct usb_serial_port *port = tty->driver_data; - int status; - struct ATENINTL_port *ATEN2011_port = usb_get_serial_port_data(port); - - if (ATEN2011_port == NULL) - return; - - if (!ATEN2011_port->open) { - dbg("%s - port not opened", __func__); - return; - } - - dbg("%s", "Entering .......... "); - - if (!tty) { - dbg("%s - no tty available", __func__); - return; - } - - /* if we are implementing XON/XOFF, send the start character */ - if (I_IXOFF(tty)) { - unsigned char start_char = START_CHAR(tty); - status = ATEN2011_write(tty, port, &start_char, 1); - if (status <= 0) - return; - } - - /* if we are implementing RTS/CTS, toggle that line */ - if (tty->termios->c_cflag & CRTSCTS) { - ATEN2011_port->shadowMCR |= MCR_RTS; - status = set_uart_reg(port, MODEM_CONTROL_REGISTER, - ATEN2011_port->shadowMCR); - if (status < 0) - return; - } - - return; -} - -static int ATEN2011_tiocmget(struct tty_struct *tty, struct file *file) -{ - struct usb_serial_port *port = tty->driver_data; - struct ATENINTL_port *ATEN2011_port; - unsigned int result; - __u16 msr; - __u16 mcr; - /* unsigned int mcr; */ - int status = 0; - ATEN2011_port = usb_get_serial_port_data(port); - - dbg("%s - port %d", __func__, port->number); - - if (ATEN2011_port == NULL) - return -ENODEV; - - status = get_uart_reg(port, MODEM_STATUS_REGISTER, &msr); - status = get_uart_reg(port, MODEM_CONTROL_REGISTER, &mcr); - /* mcr = ATEN2011_port->shadowMCR; */ - /* COMMENT2: the Fallowing three line are commented for updating only MSR values */ - result = ((mcr & MCR_DTR) ? TIOCM_DTR : 0) - | ((mcr & MCR_RTS) ? TIOCM_RTS : 0) - | ((mcr & MCR_LOOPBACK) ? TIOCM_LOOP : 0) - | ((msr & ATEN2011_MSR_CTS) ? TIOCM_CTS : 0) - | ((msr & ATEN2011_MSR_CD) ? TIOCM_CAR : 0) - | ((msr & ATEN2011_MSR_RI) ? TIOCM_RI : 0) - | ((msr & ATEN2011_MSR_DSR) ? TIOCM_DSR : 0); - - dbg("%s - 0x%04X", __func__, result); - - return result; -} - -static int ATEN2011_tiocmset(struct tty_struct *tty, struct file *file, - unsigned int set, unsigned int clear) -{ - struct usb_serial_port *port = tty->driver_data; - struct ATENINTL_port *ATEN2011_port; - unsigned int mcr; - unsigned int status; - - dbg("%s - port %d", __func__, port->number); - - ATEN2011_port = usb_get_serial_port_data(port); - - if (ATEN2011_port == NULL) - return -ENODEV; - - mcr = ATEN2011_port->shadowMCR; - if (clear & TIOCM_RTS) - mcr &= ~MCR_RTS; - if (clear & TIOCM_DTR) - mcr &= ~MCR_DTR; - if (clear & TIOCM_LOOP) - mcr &= ~MCR_LOOPBACK; - - if (set & TIOCM_RTS) - mcr |= MCR_RTS; - if (set & TIOCM_DTR) - mcr |= MCR_DTR; - if (set & TIOCM_LOOP) - mcr |= MCR_LOOPBACK; - - ATEN2011_port->shadowMCR = mcr; - - status = set_uart_reg(port, MODEM_CONTROL_REGISTER, mcr); - if (status < 0) { - dbg("setting MODEM_CONTROL_REGISTER Failed"); - return -1; - } - - return 0; -} - -static void ATEN2011_set_termios(struct tty_struct *tty, - struct usb_serial_port *port, - struct ktermios *old_termios) -{ - int status; - unsigned int cflag; - struct usb_serial *serial; - struct ATENINTL_port *ATEN2011_port; - - dbg("ATEN2011_set_termios: START"); - - serial = port->serial; - - ATEN2011_port = usb_get_serial_port_data(port); - - if (ATEN2011_port == NULL) - return; - - if (!ATEN2011_port->open) { - dbg("%s - port not opened", __func__); - return; - } - - dbg("%s", "setting termios - "); - - cflag = tty->termios->c_cflag; - - dbg("%s - cflag %08x iflag %08x", __func__, - tty->termios->c_cflag, RELEVANT_IFLAG(tty->termios->c_iflag)); - - if (old_termios) { - dbg("%s - old clfag %08x old iflag %08x", __func__, - old_termios->c_cflag, RELEVANT_IFLAG(old_termios->c_iflag)); - } - - dbg("%s - port %d", __func__, port->number); - - /* change the port settings to the new ones specified */ - - ATEN2011_change_port_settings(tty, ATEN2011_port, old_termios); - - if (!ATEN2011_port->read_urb) { - dbg("%s", "URB KILLED !!!!!"); - return; - } - - if (ATEN2011_port->read_urb->status != -EINPROGRESS) { - ATEN2011_port->read_urb->dev = serial->dev; - status = usb_submit_urb(ATEN2011_port->read_urb, GFP_ATOMIC); - if (status) { - dbg - (" usb_submit_urb(read bulk) failed, status = %d", - status); - } - } - return; -} - -static int get_lsr_info(struct tty_struct *tty, - struct ATENINTL_port *ATEN2011_port, - unsigned int __user *value) -{ - int count; - unsigned int result = 0; - - count = ATEN2011_chars_in_buffer(tty); - if (count == 0) { - dbg("%s -- Empty", __func__); - result = TIOCSER_TEMT; - } - - if (copy_to_user(value, &result, sizeof(int))) - return -EFAULT; - return 0; -} - -static int get_number_bytes_avail(struct tty_struct *tty, - struct ATENINTL_port *ATEN2011_port, - unsigned int __user *value) -{ - unsigned int result = 0; - - if (!tty) - return -ENOIOCTLCMD; - - result = tty->read_cnt; - - dbg("%s(%d) = %d", __func__, ATEN2011_port->port->number, result); - if (copy_to_user(value, &result, sizeof(int))) - return -EFAULT; - - return -ENOIOCTLCMD; -} - -static int set_modem_info(struct ATENINTL_port *ATEN2011_port, unsigned int cmd, - unsigned int __user *value) -{ - unsigned int mcr; - unsigned int arg; - __u16 Data; - int status; - struct usb_serial_port *port; - - if (ATEN2011_port == NULL) - return -1; - - port = (struct usb_serial_port *)ATEN2011_port->port; - - mcr = ATEN2011_port->shadowMCR; - - if (copy_from_user(&arg, value, sizeof(int))) - return -EFAULT; - - switch (cmd) { - case TIOCMBIS: - if (arg & TIOCM_RTS) - mcr |= MCR_RTS; - if (arg & TIOCM_DTR) - mcr |= MCR_RTS; - if (arg & TIOCM_LOOP) - mcr |= MCR_LOOPBACK; - break; - - case TIOCMBIC: - if (arg & TIOCM_RTS) - mcr &= ~MCR_RTS; - if (arg & TIOCM_DTR) - mcr &= ~MCR_RTS; - if (arg & TIOCM_LOOP) - mcr &= ~MCR_LOOPBACK; - break; - - case TIOCMSET: - /* turn off the RTS and DTR and LOOPBACK - * and then only turn on what was asked to */ - mcr &= ~(MCR_RTS | MCR_DTR | MCR_LOOPBACK); - mcr |= ((arg & TIOCM_RTS) ? MCR_RTS : 0); - mcr |= ((arg & TIOCM_DTR) ? MCR_DTR : 0); - mcr |= ((arg & TIOCM_LOOP) ? MCR_LOOPBACK : 0); - break; - } - - ATEN2011_port->shadowMCR = mcr; - - Data = ATEN2011_port->shadowMCR; - status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); - if (status < 0) { - dbg("setting MODEM_CONTROL_REGISTER Failed"); - return -1; - } - - return 0; -} - -static int get_modem_info(struct ATENINTL_port *ATEN2011_port, - unsigned int __user *value) -{ - unsigned int result = 0; - __u16 msr; - unsigned int mcr = ATEN2011_port->shadowMCR; - int status; - - status = get_uart_reg(ATEN2011_port->port, MODEM_STATUS_REGISTER, &msr); - result = ((mcr & MCR_DTR) ? TIOCM_DTR : 0) /* 0x002 */ - |((mcr & MCR_RTS) ? TIOCM_RTS : 0) /* 0x004 */ - |((msr & ATEN2011_MSR_CTS) ? TIOCM_CTS : 0) /* 0x020 */ - |((msr & ATEN2011_MSR_CD) ? TIOCM_CAR : 0) /* 0x040 */ - |((msr & ATEN2011_MSR_RI) ? TIOCM_RI : 0) /* 0x080 */ - |((msr & ATEN2011_MSR_DSR) ? TIOCM_DSR : 0); /* 0x100 */ - - dbg("%s -- %x", __func__, result); - - if (copy_to_user(value, &result, sizeof(int))) - return -EFAULT; - return 0; -} - -static int get_serial_info(struct ATENINTL_port *ATEN2011_port, - struct serial_struct __user *retinfo) -{ - struct serial_struct tmp; - - if (ATEN2011_port == NULL) - return -1; - - if (!retinfo) - return -EFAULT; - - memset(&tmp, 0, sizeof(tmp)); - - tmp.type = PORT_16550A; - tmp.line = ATEN2011_port->port->serial->minor; - if (tmp.line == SERIAL_TTY_NO_MINOR) - tmp.line = 0; - tmp.port = ATEN2011_port->port->number; - tmp.irq = 0; - tmp.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ; - tmp.xmit_fifo_size = NUM_URBS * URB_TRANSFER_BUFFER_SIZE; - tmp.baud_base = 9600; - tmp.close_delay = 5 * HZ; - tmp.closing_wait = 30 * HZ; - - if (copy_to_user(retinfo, &tmp, sizeof(*retinfo))) - return -EFAULT; - return 0; -} - -static int ATEN2011_ioctl(struct tty_struct *tty, struct file *file, - unsigned int cmd, unsigned long arg) -{ - struct usb_serial_port *port = tty->driver_data; - struct ATENINTL_port *ATEN2011_port; - struct async_icount cnow; - struct async_icount cprev; - struct serial_icounter_struct icount; - int ATENret = 0; - unsigned int __user *user_arg = (unsigned int __user *)arg; - - ATEN2011_port = usb_get_serial_port_data(port); - - if (ATEN2011_port == NULL) - return -1; - - dbg("%s - port %d, cmd = 0x%x", __func__, port->number, cmd); - - switch (cmd) { - /* return number of bytes available */ - - case TIOCINQ: - dbg("%s (%d) TIOCINQ", __func__, port->number); - return get_number_bytes_avail(tty, ATEN2011_port, user_arg); - break; - - case TIOCOUTQ: - dbg("%s (%d) TIOCOUTQ", __func__, port->number); - return put_user(ATEN2011_chars_in_buffer(tty), user_arg); - break; - - case TIOCSERGETLSR: - dbg("%s (%d) TIOCSERGETLSR", __func__, port->number); - return get_lsr_info(tty, ATEN2011_port, user_arg); - return 0; - - case TIOCMBIS: - case TIOCMBIC: - case TIOCMSET: - dbg("%s (%d) TIOCMSET/TIOCMBIC/TIOCMSET", __func__, - port->number); - ATENret = set_modem_info(ATEN2011_port, cmd, user_arg); - return ATENret; - - case TIOCMGET: - dbg("%s (%d) TIOCMGET", __func__, port->number); - return get_modem_info(ATEN2011_port, user_arg); - - case TIOCGSERIAL: - dbg("%s (%d) TIOCGSERIAL", __func__, port->number); - return get_serial_info(ATEN2011_port, - (struct serial_struct __user *)arg); - - case TIOCSSERIAL: - dbg("%s (%d) TIOCSSERIAL", __func__, port->number); - break; - - case TIOCMIWAIT: - dbg("%s (%d) TIOCMIWAIT", __func__, port->number); - cprev = ATEN2011_port->icount; - while (1) { - /* see if a signal did it */ - if (signal_pending(current)) - return -ERESTARTSYS; - cnow = ATEN2011_port->icount; - if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && - cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) - return -EIO; /* no change => error */ - if (((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) || - ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) || - ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) || - ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts))) { - return 0; - } - cprev = cnow; - } - /* NOTREACHED */ - break; - - case TIOCGICOUNT: - cnow = ATEN2011_port->icount; - icount.cts = cnow.cts; - icount.dsr = cnow.dsr; - icount.rng = cnow.rng; - icount.dcd = cnow.dcd; - icount.rx = cnow.rx; - icount.tx = cnow.tx; - icount.frame = cnow.frame; - icount.overrun = cnow.overrun; - icount.parity = cnow.parity; - icount.brk = cnow.brk; - icount.buf_overrun = cnow.buf_overrun; - - dbg("%s (%d) TIOCGICOUNT RX=%d, TX=%d", __func__, - port->number, icount.rx, icount.tx); - if (copy_to_user((void __user *)arg, &icount, sizeof(icount))) - return -EFAULT; - return 0; - - default: - break; - } - - return -ENOIOCTLCMD; -} - -static int ATEN2011_calc_baud_rate_divisor(int baudRate, int *divisor, - __u16 *clk_sel_val) -{ - dbg("%s - %d", __func__, baudRate); - - if (baudRate <= 115200) { - *divisor = 115200 / baudRate; - *clk_sel_val = 0x0; - } - if ((baudRate > 115200) && (baudRate <= 230400)) { - *divisor = 230400 / baudRate; - *clk_sel_val = 0x10; - } else if ((baudRate > 230400) && (baudRate <= 403200)) { - *divisor = 403200 / baudRate; - *clk_sel_val = 0x20; - } else if ((baudRate > 403200) && (baudRate <= 460800)) { - *divisor = 460800 / baudRate; - *clk_sel_val = 0x30; - } else if ((baudRate > 460800) && (baudRate <= 806400)) { - *divisor = 806400 / baudRate; - *clk_sel_val = 0x40; - } else if ((baudRate > 806400) && (baudRate <= 921600)) { - *divisor = 921600 / baudRate; - *clk_sel_val = 0x50; - } else if ((baudRate > 921600) && (baudRate <= 1572864)) { - *divisor = 1572864 / baudRate; - *clk_sel_val = 0x60; - } else if ((baudRate > 1572864) && (baudRate <= 3145728)) { - *divisor = 3145728 / baudRate; - *clk_sel_val = 0x70; - } - return 0; -} - -static int ATEN2011_send_cmd_write_baud_rate(struct ATENINTL_port - *ATEN2011_port, int baudRate) -{ - int divisor = 0; - int status; - __u16 Data; - unsigned char number; - __u16 clk_sel_val; - struct usb_serial_port *port; - int minor; - - if (ATEN2011_port == NULL) - return -1; - - port = (struct usb_serial_port *)ATEN2011_port->port; - - dbg("%s", "Entering .......... "); - - minor = ATEN2011_port->port->serial->minor; - if (minor == SERIAL_TTY_NO_MINOR) - minor = 0; - number = ATEN2011_port->port->number - minor; - - dbg("%s - port = %d, baud = %d", __func__, - ATEN2011_port->port->number, baudRate); - /* reset clk_uart_sel in spregOffset */ - if (baudRate > 115200) { -#ifdef HW_flow_control - /* - * NOTE: need to see the pther register to modify - * setting h/w flow control bit to 1; - */ - /* Data = ATEN2011_port->shadowMCR; */ - Data = 0x2b; - ATEN2011_port->shadowMCR = Data; - status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); - if (status < 0) { - dbg("Writing spreg failed in set_serial_baud"); - return -1; - } -#endif - - } else { -#ifdef HW_flow_control - /* setting h/w flow control bit to 0; */ - /* Data = ATEN2011_port->shadowMCR; */ - Data = 0xb; - ATEN2011_port->shadowMCR = Data; - status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); - if (status < 0) { - dbg("Writing spreg failed in set_serial_baud"); - return -1; - } -#endif - - } - - if (1) /* baudRate <= 115200) */ { - clk_sel_val = 0x0; - Data = 0x0; - status = - ATEN2011_calc_baud_rate_divisor(baudRate, &divisor, - &clk_sel_val); - status = get_reg_sync(port, ATEN2011_port->SpRegOffset, &Data); - if (status < 0) { - dbg("reading spreg failed in set_serial_baud"); - return -1; - } - Data = (Data & 0x8f) | clk_sel_val; - status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data); - if (status < 0) { - dbg("Writing spreg failed in set_serial_baud"); - return -1; - } - /* Calculate the Divisor */ - - if (status) { - err("%s - bad baud rate", __func__); - dbg("%s", "bad baud rate"); - return status; - } - /* Enable access to divisor latch */ - Data = ATEN2011_port->shadowLCR | SERIAL_LCR_DLAB; - ATEN2011_port->shadowLCR = Data; - set_uart_reg(port, LINE_CONTROL_REGISTER, Data); - - /* Write the divisor */ - Data = (unsigned char)(divisor & 0xff); - dbg("set_serial_baud Value to write DLL is %x", Data); - set_uart_reg(port, DIVISOR_LATCH_LSB, Data); - - Data = (unsigned char)((divisor & 0xff00) >> 8); - dbg("set_serial_baud Value to write DLM is %x", Data); - set_uart_reg(port, DIVISOR_LATCH_MSB, Data); - - /* Disable access to divisor latch */ - Data = ATEN2011_port->shadowLCR & ~SERIAL_LCR_DLAB; - ATEN2011_port->shadowLCR = Data; - set_uart_reg(port, LINE_CONTROL_REGISTER, Data); - - } - - return status; -} - -static void ATEN2011_change_port_settings(struct tty_struct *tty, - struct ATENINTL_port *ATEN2011_port, - struct ktermios *old_termios) -{ - int baud; - unsigned cflag; - unsigned iflag; - __u8 lData; - __u8 lParity; - __u8 lStop; - int status; - __u16 Data; - struct usb_serial_port *port; - struct usb_serial *serial; - - if (ATEN2011_port == NULL) - return; - - port = (struct usb_serial_port *)ATEN2011_port->port; - - serial = port->serial; - - dbg("%s - port %d", __func__, ATEN2011_port->port->number); - - if (!ATEN2011_port->open) { - dbg("%s - port not opened", __func__); - return; - } - - if ((!tty) || (!tty->termios)) { - dbg("%s - no tty structures", __func__); - return; - } - - dbg("%s", "Entering .......... "); - - lData = LCR_BITS_8; - lStop = LCR_STOP_1; - lParity = LCR_PAR_NONE; - - cflag = tty->termios->c_cflag; - iflag = tty->termios->c_iflag; - - /* Change the number of bits */ - - /* COMMENT1: the below Line"if(cflag & CSIZE)" is added for the errors we get for serial loop data test i.e serial_loopback.pl -v */ - /* if(cflag & CSIZE) */ - { - switch (cflag & CSIZE) { - case CS5: - lData = LCR_BITS_5; - break; - - case CS6: - lData = LCR_BITS_6; - break; - - case CS7: - lData = LCR_BITS_7; - break; - default: - case CS8: - lData = LCR_BITS_8; - break; - } - } - /* Change the Parity bit */ - if (cflag & PARENB) { - if (cflag & PARODD) { - lParity = LCR_PAR_ODD; - dbg("%s - parity = odd", __func__); - } else { - lParity = LCR_PAR_EVEN; - dbg("%s - parity = even", __func__); - } - - } else { - dbg("%s - parity = none", __func__); - } - - if (cflag & CMSPAR) - lParity = lParity | 0x20; - - /* Change the Stop bit */ - if (cflag & CSTOPB) { - lStop = LCR_STOP_2; - dbg("%s - stop bits = 2", __func__); - } else { - lStop = LCR_STOP_1; - dbg("%s - stop bits = 1", __func__); - } - - /* Update the LCR with the correct value */ - ATEN2011_port->shadowLCR &= - ~(LCR_BITS_MASK | LCR_STOP_MASK | LCR_PAR_MASK); - ATEN2011_port->shadowLCR |= (lData | lParity | lStop); - - dbg - ("ATEN2011_change_port_settings ATEN2011_port->shadowLCR is %x", - ATEN2011_port->shadowLCR); - /* Disable Interrupts */ - Data = 0x00; - set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data); - - Data = 0x00; - set_uart_reg(port, FIFO_CONTROL_REGISTER, Data); - - Data = 0xcf; - set_uart_reg(port, FIFO_CONTROL_REGISTER, Data); - - /* Send the updated LCR value to the ATEN2011 */ - Data = ATEN2011_port->shadowLCR; - - set_uart_reg(port, LINE_CONTROL_REGISTER, Data); - - Data = 0x00b; - ATEN2011_port->shadowMCR = Data; - set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); - Data = 0x00b; - set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); - - /* set up the MCR register and send it to the ATEN2011 */ - - ATEN2011_port->shadowMCR = MCR_MASTER_IE; - if (cflag & CBAUD) - ATEN2011_port->shadowMCR |= (MCR_DTR | MCR_RTS); - - if (cflag & CRTSCTS) - ATEN2011_port->shadowMCR |= (MCR_XON_ANY); - else - ATEN2011_port->shadowMCR &= ~(MCR_XON_ANY); - - Data = ATEN2011_port->shadowMCR; - set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); - - /* Determine divisor based on baud rate */ - baud = tty_get_baud_rate(tty); - - if (!baud) { - /* pick a default, any default... */ - dbg("%s", "Picked default baud..."); - baud = 9600; - } - - dbg("%s - baud rate = %d", __func__, baud); - status = ATEN2011_send_cmd_write_baud_rate(ATEN2011_port, baud); - - /* Enable Interrupts */ - Data = 0x0c; - set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data); - - if (ATEN2011_port->read_urb->status != -EINPROGRESS) { - ATEN2011_port->read_urb->dev = serial->dev; - - status = usb_submit_urb(ATEN2011_port->read_urb, GFP_ATOMIC); - - if (status) { - dbg - (" usb_submit_urb(read bulk) failed, status = %d", - status); - } - } - dbg - ("ATEN2011_change_port_settings ATEN2011_port->shadowLCR is End %x", - ATEN2011_port->shadowLCR); - - return; -} - -static int ATEN2011_calc_num_ports(struct usb_serial *serial) -{ - - __u16 Data = 0x00; - int ret = 0; - int ATEN2011_2or4ports; - ret = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), - ATEN_RDREQ, ATEN_RD_RTYPE, 0, GPIO_REGISTER, - &Data, VENDOR_READ_LENGTH, ATEN_WDR_TIMEOUT); - -/* ghostgum: here is where the problem appears to bet */ -/* Which of the following are needed? */ -/* Greg used the serial->type->num_ports=2 */ -/* But the code in the ATEN2011_open relies on serial->num_ports=2 */ - if ((Data & 0x01) == 0) { - ATEN2011_2or4ports = 2; - serial->type->num_ports = 2; - serial->num_ports = 2; - } - /* else if(serial->interface->cur_altsetting->desc.bNumEndpoints == 9) */ - else { - ATEN2011_2or4ports = 4; - serial->type->num_ports = 4; - serial->num_ports = 4; - - } - - return ATEN2011_2or4ports; -} - -static int ATEN2011_startup(struct usb_serial *serial) -{ - struct ATENINTL_serial *ATEN2011_serial; - struct ATENINTL_port *ATEN2011_port; - struct usb_device *dev; - int i, status; - int minor; - - __u16 Data; - dbg("%s", " ATEN2011_startup :entering.........."); - - if (!serial) { - dbg("%s", "Invalid Handler"); - return -1; - } - - dev = serial->dev; - - dbg("%s", "Entering..."); - - /* create our private serial structure */ - ATEN2011_serial = kzalloc(sizeof(struct ATENINTL_serial), GFP_KERNEL); - if (ATEN2011_serial == NULL) { - err("%s - Out of memory", __func__); - return -ENOMEM; - } - - /* resetting the private structure field values to zero */ - memset(ATEN2011_serial, 0, sizeof(struct ATENINTL_serial)); - - ATEN2011_serial->serial = serial; - /* initilize status polling flag to 0 */ - ATEN2011_serial->status_polling_started = 0; - - usb_set_serial_data(serial, ATEN2011_serial); - ATEN2011_serial->ATEN2011_spectrum_2or4ports = - ATEN2011_calc_num_ports(serial); - /* we set up the pointers to the endpoints in the ATEN2011_open * - * function, as the structures aren't created yet. */ - - /* set up port private structures */ - for (i = 0; i < serial->num_ports; ++i) { - ATEN2011_port = - kmalloc(sizeof(struct ATENINTL_port), GFP_KERNEL); - if (ATEN2011_port == NULL) { - err("%s - Out of memory", __func__); - usb_set_serial_data(serial, NULL); - kfree(ATEN2011_serial); - return -ENOMEM; - } - memset(ATEN2011_port, 0, sizeof(struct ATENINTL_port)); - - /* - * Initialize all port interrupt end point to port 0 - * int endpoint. Our device has only one interrupt end point - * comman to all port - */ - /* serial->port[i]->interrupt_in_endpointAddress = serial->port[0]->interrupt_in_endpointAddress; */ - - ATEN2011_port->port = serial->port[i]; - usb_set_serial_port_data(serial->port[i], ATEN2011_port); - - minor = serial->port[i]->serial->minor; - if (minor == SERIAL_TTY_NO_MINOR) - minor = 0; - ATEN2011_port->port_num = - ((serial->port[i]->number - minor) + 1); - - if (ATEN2011_port->port_num == 1) { - ATEN2011_port->SpRegOffset = 0x0; - ATEN2011_port->ControlRegOffset = 0x1; - ATEN2011_port->DcrRegOffset = 0x4; - } else if ((ATEN2011_port->port_num == 2) - && (ATEN2011_serial->ATEN2011_spectrum_2or4ports == - 4)) { - ATEN2011_port->SpRegOffset = 0x8; - ATEN2011_port->ControlRegOffset = 0x9; - ATEN2011_port->DcrRegOffset = 0x16; - } else if ((ATEN2011_port->port_num == 2) - && (ATEN2011_serial->ATEN2011_spectrum_2or4ports == - 2)) { - ATEN2011_port->SpRegOffset = 0xa; - ATEN2011_port->ControlRegOffset = 0xb; - ATEN2011_port->DcrRegOffset = 0x19; - } else if ((ATEN2011_port->port_num == 3) - && (ATEN2011_serial->ATEN2011_spectrum_2or4ports == - 4)) { - ATEN2011_port->SpRegOffset = 0xa; - ATEN2011_port->ControlRegOffset = 0xb; - ATEN2011_port->DcrRegOffset = 0x19; - } else if ((ATEN2011_port->port_num == 4) - && (ATEN2011_serial->ATEN2011_spectrum_2or4ports == - 4)) { - ATEN2011_port->SpRegOffset = 0xc; - ATEN2011_port->ControlRegOffset = 0xd; - ATEN2011_port->DcrRegOffset = 0x1c; - } - - usb_set_serial_port_data(serial->port[i], ATEN2011_port); - - /* enable rx_disable bit in control register */ - - status = get_reg_sync(serial->port[i], - ATEN2011_port->ControlRegOffset, &Data); - if (status < 0) { - dbg("Reading ControlReg failed status-0x%x", - status); - break; - } else - dbg - ("ControlReg Reading success val is %x, status%d", - Data, status); - Data |= 0x08; /* setting driver done bit */ - Data |= 0x04; /* sp1_bit to have cts change reflect in modem status reg */ - - /* Data |= 0x20; */ /* rx_disable bit */ - status = set_reg_sync(serial->port[i], - ATEN2011_port->ControlRegOffset, Data); - if (status < 0) { - dbg - ("Writing ControlReg failed(rx_disable) status-0x%x", - status); - break; - } else - dbg - ("ControlReg Writing success(rx_disable) status%d", - status); - - /* - * Write default values in DCR (i.e 0x01 in DCR0, 0x05 in DCR2 - * and 0x24 in DCR3 - */ - Data = 0x01; - status = set_reg_sync(serial->port[i], - (__u16)(ATEN2011_port->DcrRegOffset + 0), - Data); - if (status < 0) { - dbg("Writing DCR0 failed status-0x%x", status); - break; - } else - dbg("DCR0 Writing success status%d", status); - - Data = 0x05; - status = set_reg_sync(serial->port[i], - (__u16)(ATEN2011_port->DcrRegOffset + 1), - Data); - if (status < 0) { - dbg("Writing DCR1 failed status-0x%x", status); - break; - } else - dbg("DCR1 Writing success status%d", status); - - Data = 0x24; - status = set_reg_sync(serial->port[i], - (__u16)(ATEN2011_port->DcrRegOffset + 2), - Data); - if (status < 0) { - dbg("Writing DCR2 failed status-0x%x", status); - break; - } else - dbg("DCR2 Writing success status%d", status); - - /* write values in clkstart0x0 and clkmulti 0x20 */ - Data = 0x0; - status = set_reg_sync(serial->port[i], CLK_START_VALUE_REGISTER, - Data); - if (status < 0) { - dbg - ("Writing CLK_START_VALUE_REGISTER failed status-0x%x", - status); - break; - } else - dbg - ("CLK_START_VALUE_REGISTER Writing success status%d", - status); - - Data = 0x20; - status = set_reg_sync(serial->port[i], CLK_MULTI_REGISTER, - Data); - if (status < 0) { - dbg - ("Writing CLK_MULTI_REGISTER failed status-0x%x", - status); - break; - } else - dbg("CLK_MULTI_REGISTER Writing success status%d", - status); - - /* Zero Length flag register */ - if ((ATEN2011_port->port_num != 1) - && (ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2)) { - - Data = 0xff; - status = set_reg_sync(serial->port[i], - (__u16)(ZLP_REG1 + ((__u16)ATEN2011_port->port_num)), - Data); - dbg("ZLIP offset%x", - (__u16) (ZLP_REG1 + - ((__u16) ATEN2011_port->port_num))); - if (status < 0) { - dbg - ("Writing ZLP_REG%d failed status-0x%x", - i + 2, status); - break; - } else - dbg("ZLP_REG%d Writing success status%d", - i + 2, status); - } else { - Data = 0xff; - status = set_reg_sync(serial->port[i], - (__u16)(ZLP_REG1 + ((__u16)ATEN2011_port->port_num) - 0x1), - Data); - dbg("ZLIP offset%x", - (__u16) (ZLP_REG1 + - ((__u16) ATEN2011_port->port_num) - - 0x1)); - if (status < 0) { - dbg - ("Writing ZLP_REG%d failed status-0x%x", - i + 1, status); - break; - } else - dbg("ZLP_REG%d Writing success status%d", - i + 1, status); - - } - ATEN2011_port->control_urb = usb_alloc_urb(0, GFP_ATOMIC); - ATEN2011_port->ctrl_buf = kmalloc(16, GFP_KERNEL); - - } - - /* Zero Length flag enable */ - Data = 0x0f; - status = set_reg_sync(serial->port[0], ZLP_REG5, Data); - if (status < 0) { - dbg("Writing ZLP_REG5 failed status-0x%x", status); - return -1; - } else - dbg("ZLP_REG5 Writing success status%d", status); - - /* setting configuration feature to one */ - usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), - (__u8) 0x03, 0x00, 0x01, 0x00, NULL, 0x00, 5 * HZ); - return 0; -} - -static void ATEN2011_release(struct usb_serial *serial) -{ - int i; - struct ATENINTL_port *ATEN2011_port; - - /* check for the ports to be closed,close the ports and disconnect */ - - /* free private structure allocated for serial port * - * stop reads and writes on all ports */ - - for (i = 0; i < serial->num_ports; ++i) { - ATEN2011_port = usb_get_serial_port_data(serial->port[i]); - kfree(ATEN2011_port->ctrl_buf); - usb_kill_urb(ATEN2011_port->control_urb); - kfree(ATEN2011_port); - usb_set_serial_port_data(serial->port[i], NULL); - } - - /* free private structure allocated for serial device */ - - kfree(usb_get_serial_data(serial)); - usb_set_serial_data(serial, NULL); -} - -static struct usb_serial_driver aten_serial_driver = { - .driver = { - .owner = THIS_MODULE, - .name = "aten2011", - }, - .description = DRIVER_DESC, - .id_table = id_table, - .open = ATEN2011_open, - .close = ATEN2011_close, - .write = ATEN2011_write, - .write_room = ATEN2011_write_room, - .chars_in_buffer = ATEN2011_chars_in_buffer, - .throttle = ATEN2011_throttle, - .unthrottle = ATEN2011_unthrottle, - .calc_num_ports = ATEN2011_calc_num_ports, - - .ioctl = ATEN2011_ioctl, - .set_termios = ATEN2011_set_termios, - .break_ctl = ATEN2011_break, - .tiocmget = ATEN2011_tiocmget, - .tiocmset = ATEN2011_tiocmset, - .attach = ATEN2011_startup, - .release = ATEN2011_release, - .read_bulk_callback = ATEN2011_bulk_in_callback, - .read_int_callback = ATEN2011_interrupt_callback, -}; - -static struct usb_driver aten_driver = { - .name = "aten2011", - .probe = usb_serial_probe, - .disconnect = usb_serial_disconnect, - .id_table = id_table, -}; - -static int __init aten_init(void) -{ - int retval; - - /* Register with the usb serial */ - retval = usb_serial_register(&aten_serial_driver); - if (retval) - return retval; - - printk(KERN_INFO KBUILD_MODNAME ":" - DRIVER_DESC " " DRIVER_VERSION "\n"); - - /* Register with the usb */ - retval = usb_register(&aten_driver); - if (retval) - usb_serial_deregister(&aten_serial_driver); - - return retval; -} - -static void __exit aten_exit(void) -{ - usb_deregister(&aten_driver); - usb_serial_deregister(&aten_serial_driver); -} - -module_init(aten_init); -module_exit(aten_exit); - -/* Module information */ -MODULE_DESCRIPTION(DRIVER_DESC); -MODULE_LICENSE("GPL"); - -MODULE_PARM_DESC(debug, "Debug enabled or not"); -- GitLab From fb29900217bd89370974870d47cab07bad3e5ac4 Mon Sep 17 00:00:00 2001 From: Amit Kucheria Date: Mon, 27 Jul 2009 12:01:03 +0300 Subject: [PATCH 0411/1342] staging: udlfb: Add vmalloc.h include Required for vmalloc_32 and vfree declarations on non-x86 platforms. Signed-off-by: Amit Kucheria Signed-off-by: Greg Kroah-Hartman --- drivers/staging/udlfb/udlfb.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/staging/udlfb/udlfb.c b/drivers/staging/udlfb/udlfb.c index 0ab9d15f343..f5416af1e90 100644 --- a/drivers/staging/udlfb/udlfb.c +++ b/drivers/staging/udlfb/udlfb.c @@ -21,6 +21,7 @@ #include #include #include +#include #include "udlfb.h" -- GitLab From 38ceb592fcac9110c6b3c87ea0a27bff68c43486 Mon Sep 17 00:00:00 2001 From: Lai Jiangshan Date: Tue, 28 Jul 2009 20:11:24 +0800 Subject: [PATCH 0412/1342] tracing: Fix invalid function_graph entry When print_graph_entry() computes a function call entry event, it needs to also check the next entry to guess if it matches the return event of the current function entry. In order to look at this next event, it needs to consume the current entry before going ahead in the ring buffer. However, if the current event that gets consumed is the last one in the ring buffer head page, the ring_buffer may reuse the page for writers. The consumed entry will then become invalid because of possible racy overwriting. Me must then handle this entry by making a copy of it. The fix also applies on 2.6.30 Signed-off-by: Lai Jiangshan Cc: Steven Rostedt Cc: stable@kernel.org LKML-Reference: <4A6EEAEC.3050508@cn.fujitsu.com> Signed-off-by: Frederic Weisbecker --- kernel/trace/trace_functions_graph.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-) diff --git a/kernel/trace/trace_functions_graph.c b/kernel/trace/trace_functions_graph.c index d2249abafb5..420ec348757 100644 --- a/kernel/trace/trace_functions_graph.c +++ b/kernel/trace/trace_functions_graph.c @@ -843,9 +843,16 @@ print_graph_function(struct trace_iterator *iter) switch (entry->type) { case TRACE_GRAPH_ENT: { - struct ftrace_graph_ent_entry *field; + /* + * print_graph_entry() may consume the current event, + * thus @field may become invalid, so we need to save it. + * sizeof(struct ftrace_graph_ent_entry) is very small, + * it can be safely saved at the stack. + */ + struct ftrace_graph_ent_entry *field, saved; trace_assign_type(field, entry); - return print_graph_entry(field, s, iter); + saved = *field; + return print_graph_entry(&saved, s, iter); } case TRACE_GRAPH_RET: { struct ftrace_graph_ret_entry *field; -- GitLab From 74e7ff8c50b6b022e6ffaa736b16a4dc161d3eaf Mon Sep 17 00:00:00 2001 From: Lai Jiangshan Date: Tue, 28 Jul 2009 20:17:22 +0800 Subject: [PATCH 0413/1342] tracing: Fix missing function_graph events when we splice_read from trace_pipe About a half events are missing when we splice_read from trace_pipe. They are unexpectedly consumed because we ignore the TRACE_TYPE_NO_CONSUME return value used by the function graph tracer when it needs to consume the events by itself to walk on the ring buffer. The same problem appears with ftrace_dump() Example of an output before this patch: 1) | ktime_get_real() { 1) 2.846 us | read_hpet(); 1) 4.558 us | } 1) 6.195 us | } After this patch: 0) | ktime_get_real() { 0) | getnstimeofday() { 0) 1.960 us | read_hpet(); 0) 3.597 us | } 0) 5.196 us | } The fix also applies on 2.6.30 Signed-off-by: Lai Jiangshan Cc: Steven Rostedt Cc: stable@kernel.org LKML-Reference: <4A6EEC52.90704@cn.fujitsu.com> Signed-off-by: Frederic Weisbecker --- kernel/trace/trace.c | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-) diff --git a/kernel/trace/trace.c b/kernel/trace/trace.c index 8bc8d8afea6..da984ad065a 100644 --- a/kernel/trace/trace.c +++ b/kernel/trace/trace.c @@ -3085,7 +3085,8 @@ tracing_fill_pipe_page(size_t rem, struct trace_iterator *iter) break; } - trace_consume(iter); + if (ret != TRACE_TYPE_NO_CONSUME) + trace_consume(iter); rem -= count; if (!find_next_entry_inc(iter)) { rem = 0; @@ -4233,8 +4234,11 @@ static void __ftrace_dump(bool disable_tracing) iter.pos = -1; if (find_next_entry_inc(&iter) != NULL) { - print_trace_line(&iter); - trace_consume(&iter); + int ret; + + ret = print_trace_line(&iter); + if (ret != TRACE_TYPE_NO_CONSUME) + trace_consume(&iter); } trace_printk_seq(&iter.seq); -- GitLab From 6352a29305373ae6196491e6d4669f301e26492e Mon Sep 17 00:00:00 2001 From: Tyler Hicks Date: Tue, 28 Jul 2009 13:57:01 -0500 Subject: [PATCH 0414/1342] eCryptfs: Check Tag 11 literal data buffer size Tag 11 packets are stored in the metadata section of an eCryptfs file to store the key signature(s) used to encrypt the file encryption key. After extracting the packet length field to determine the key signature length, a check is not performed to see if the length would exceed the key signature buffer size that was passed into parse_tag_11_packet(). Thanks to Ramon de Carvalho Valle for finding this bug using fsfuzzer. Signed-off-by: Tyler Hicks Cc: stable@kernel.org (2.6.27 and 30) Signed-off-by: Linus Torvalds --- fs/ecryptfs/keystore.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/fs/ecryptfs/keystore.c b/fs/ecryptfs/keystore.c index af737bb56cb..5414253d4c9 100644 --- a/fs/ecryptfs/keystore.c +++ b/fs/ecryptfs/keystore.c @@ -1449,6 +1449,12 @@ parse_tag_11_packet(unsigned char *data, unsigned char *contents, rc = -EINVAL; goto out; } + if (unlikely((*tag_11_contents_size) > max_contents_bytes)) { + printk(KERN_ERR "Literal data section in tag 11 packet exceeds " + "expected size\n"); + rc = -EINVAL; + goto out; + } if (data[(*packet_size)++] != 0x62) { printk(KERN_WARNING "Unrecognizable packet\n"); rc = -EINVAL; -- GitLab From f151cd2c54ddc7714e2f740681350476cda03a28 Mon Sep 17 00:00:00 2001 From: Ramon de Carvalho Valle Date: Tue, 28 Jul 2009 13:58:22 -0500 Subject: [PATCH 0415/1342] eCryptfs: parse_tag_3_packet check tag 3 packet encrypted key size The parse_tag_3_packet function does not check if the tag 3 packet contains a encrypted key size larger than ECRYPTFS_MAX_ENCRYPTED_KEY_BYTES. Signed-off-by: Ramon de Carvalho Valle [tyhicks@linux.vnet.ibm.com: Added printk newline and changed goto to out_free] Signed-off-by: Tyler Hicks Cc: stable@kernel.org (2.6.27 and 30) Signed-off-by: Linus Torvalds --- fs/ecryptfs/keystore.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/fs/ecryptfs/keystore.c b/fs/ecryptfs/keystore.c index 5414253d4c9..259525c9abb 100644 --- a/fs/ecryptfs/keystore.c +++ b/fs/ecryptfs/keystore.c @@ -1303,6 +1303,13 @@ parse_tag_3_packet(struct ecryptfs_crypt_stat *crypt_stat, } (*new_auth_tok)->session_key.encrypted_key_size = (body_size - (ECRYPTFS_SALT_SIZE + 5)); + if ((*new_auth_tok)->session_key.encrypted_key_size + > ECRYPTFS_MAX_ENCRYPTED_KEY_BYTES) { + printk(KERN_WARNING "Tag 3 packet contains key larger " + "than ECRYPTFS_MAX_ENCRYPTED_KEY_BYTES\n"); + rc = -EINVAL; + goto out_free; + } if (unlikely(data[(*packet_size)++] != 0x04)) { printk(KERN_WARNING "Unknown version number [%d]\n", data[(*packet_size) - 1]); -- GitLab From ce4adcc6e5320062e0d993eb75152d165aaabbe6 Mon Sep 17 00:00:00 2001 From: Andreas Eversberg Date: Mon, 27 Jul 2009 19:24:04 +0200 Subject: [PATCH 0416/1342] mISDN: Fix handling of receive buffer size in L1oIP The size of receive buffer pointer was used to get size of receive buffer instead of recvbuf_size itself, so only 4/8 bytes could be transfered. This is a regression to 2.6.30 introduced by commit 8c90e11e3543d7de612194a042a148caeaab5f1d ("mISDN: Use kernel_{send,recv}msg instead of open coding") Signed-off-by: Andreas Eversberg Signed-off-by: Karsten Keil Signed-off-by: Linus Torvalds --- drivers/isdn/mISDN/l1oip_core.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/isdn/mISDN/l1oip_core.c b/drivers/isdn/mISDN/l1oip_core.c index 990e6a7e667..c3b661a666c 100644 --- a/drivers/isdn/mISDN/l1oip_core.c +++ b/drivers/isdn/mISDN/l1oip_core.c @@ -731,10 +731,10 @@ l1oip_socket_thread(void *data) while (!signal_pending(current)) { struct kvec iov = { .iov_base = recvbuf, - .iov_len = sizeof(recvbuf), + .iov_len = recvbuf_size, }; recvlen = kernel_recvmsg(socket, &msg, &iov, 1, - sizeof(recvbuf), 0); + recvbuf_size, 0); if (recvlen > 0) { l1oip_socket_parse(hc, &sin_rx, recvbuf, recvlen); } else { -- GitLab From f99aa3f9b67ca8c29dc29ef3fc453f0343206c46 Mon Sep 17 00:00:00 2001 From: "Carlos R. Mafra" Date: Mon, 13 Jul 2009 21:45:03 +0200 Subject: [PATCH 0417/1342] USB: option: Remove unused variable After commit f092c240494f2d807401d93f95f683909b90af96 ("USB: option: remove unnecessary and erroneous code") the variable 'serial' becomes unused, as gcc-4.3.2 points out: drivers/usb/serial/option.c: In function 'option_instat_callback': drivers/usb/serial/option.c:834: warning: unused variable 'serial' drivers/usb/serial/option.c: In function 'option_open': drivers/usb/serial/option.c:930: warning: unused variable 'serial' So I removed it. Signed-off-by: Carlos R. Mafra Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 98262dd552b..77b9563ec43 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -831,7 +831,6 @@ static void option_instat_callback(struct urb *urb) int status = urb->status; struct usb_serial_port *port = urb->context; struct option_port_private *portdata = usb_get_serial_port_data(port); - struct usb_serial *serial = port->serial; dbg("%s", __func__); dbg("%s: urb %p port %p has data %p", __func__, urb, port, portdata); @@ -927,7 +926,6 @@ static int option_open(struct tty_struct *tty, struct usb_serial_port *port, struct file *filp) { struct option_port_private *portdata; - struct usb_serial *serial = port->serial; int i, err; struct urb *urb; -- GitLab From 5f4fab91f2b12c12f0506b4da49ed199db8c64ed Mon Sep 17 00:00:00 2001 From: Oliver Neukum Date: Mon, 13 Jul 2009 23:24:10 +0200 Subject: [PATCH 0418/1342] USB: let the option driver compile without CONFIG_PM This is needed for compilation without CONFIG_PM. Signed-off-by: Oliver Neukum Acked-by: Randy Dunlap Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 77b9563ec43..7638d2632ff 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -66,8 +66,10 @@ static int option_tiocmget(struct tty_struct *tty, struct file *file); static int option_tiocmset(struct tty_struct *tty, struct file *file, unsigned int set, unsigned int clear); static int option_send_setup(struct usb_serial_port *port); +#ifdef CONFIG_PM static int option_suspend(struct usb_serial *serial, pm_message_t message); static int option_resume(struct usb_serial *serial); +#endif /* Vendor and product IDs */ #define OPTION_VENDOR_ID 0x0AF0 @@ -555,8 +557,10 @@ static struct usb_driver option_driver = { .name = "option", .probe = usb_serial_probe, .disconnect = usb_serial_disconnect, +#ifdef CONFIG_PM .suspend = usb_serial_suspend, .resume = usb_serial_resume, +#endif .id_table = option_ids, .no_dynamic_id = 1, }; @@ -588,8 +592,10 @@ static struct usb_serial_driver option_1port_device = { .disconnect = option_disconnect, .release = option_release, .read_int_callback = option_instat_callback, +#ifdef CONFIG_PM .suspend = option_suspend, .resume = option_resume, +#endif }; static int debug; @@ -1185,6 +1191,7 @@ static void option_release(struct usb_serial *serial) } } +#ifdef CONFIG_PM static int option_suspend(struct usb_serial *serial, pm_message_t message) { dbg("%s entered", __func__); @@ -1243,6 +1250,7 @@ static int option_resume(struct usb_serial *serial) } return 0; } +#endif MODULE_AUTHOR(DRIVER_AUTHOR); MODULE_DESCRIPTION(DRIVER_DESC); -- GitLab From 7a777919bbeec3eac1d7904a728a60e9c2bb9c67 Mon Sep 17 00:00:00 2001 From: Giacomo Lozito Date: Mon, 13 Jul 2009 23:23:33 +0200 Subject: [PATCH 0419/1342] USB: storage: raise timeout in usb_stor_Bulk_max_lun Requests to get max LUN, for certain USB storage devices, require a longer timeout before a correct reply is returned. This happens for a Realtek USB Card Reader (0bda:0152), which has a max LUN of 3 but is set to 0, thus losing functionality, because of the timeout occurring too quickly. Raising the timeout value fixes the issue and might help other devices to return a correct max LUN value as well. Signed-off-by: Giacomo Lozito Acked-by: Alan Stern Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/transport.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/storage/transport.c b/drivers/usb/storage/transport.c index fcb32021721..e20dc525d17 100644 --- a/drivers/usb/storage/transport.c +++ b/drivers/usb/storage/transport.c @@ -961,7 +961,7 @@ int usb_stor_Bulk_max_lun(struct us_data *us) US_BULK_GET_MAX_LUN, USB_DIR_IN | USB_TYPE_CLASS | USB_RECIP_INTERFACE, - 0, us->ifnum, us->iobuf, 1, HZ); + 0, us->ifnum, us->iobuf, 1, 10*HZ); US_DEBUGP("GetMaxLUN command result is %d, data is %d\n", result, us->iobuf[0]); -- GitLab From 715bfc22ce952a14fac0b9200fd70d81c1951091 Mon Sep 17 00:00:00 2001 From: Anand Gadiyar Date: Tue, 14 Jul 2009 16:41:00 +0530 Subject: [PATCH 0420/1342] USB: OMAP: OHCI: hc_driver's stop method should call ohci_stop OMAP: OHCI: hc_driver's stop method should call ohci_stop Without this, the ohci-omap driver will not cleanup the debugfs nodes when the driver is unloaded. So the next insmod will fail, if CONFIG_DEBUG_FS and CONFIG_USB_DEBUG are both selected. Reported-by: vikram pandita Cc: David Brownell Signed-off-by: Anand Gadiyar Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ohci-omap.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c index f3aaba35e91..83cbecd2a1e 100644 --- a/drivers/usb/host/ohci-omap.c +++ b/drivers/usb/host/ohci-omap.c @@ -282,6 +282,7 @@ static int ohci_omap_init(struct usb_hcd *hcd) static void ohci_omap_stop(struct usb_hcd *hcd) { dev_dbg(hcd->self.controller, "stopping USB Controller\n"); + ohci_stop(hcd); omap_ohci_clock_power(0); } -- GitLab From fca4404c55ab44c7413769f1d9c66451103711a5 Mon Sep 17 00:00:00 2001 From: Ville Sundberg Date: Wed, 15 Jul 2009 00:27:28 +0300 Subject: [PATCH 0421/1342] USB: ftdi_sio: Add support for GN Otometrics Aurical USB Audiometer The patch adds support for the GN Otometrics Aurical USB Audiometer (FT232BM-based). A new VID and a new PID is added. Signed-off-by: Ville Sundberg Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 1 + drivers/usb/serial/ftdi_sio.h | 7 +++++++ 2 files changed, 8 insertions(+) diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 60c64cc5be2..b574878c78b 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -698,6 +698,7 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(MARVELL_VID, MARVELL_SHEEVAPLUG_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(LARSENBRUSGAARD_VID, LB_ALTITRACK_PID) }, + { USB_DEVICE(GN_OTOMETRICS_VID, AURICAL_USB_PID) }, { }, /* Optional parameter entry */ { } /* Terminating entry */ }; diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h index c9fbd741509..24dbd99e87d 100644 --- a/drivers/usb/serial/ftdi_sio.h +++ b/drivers/usb/serial/ftdi_sio.h @@ -946,6 +946,13 @@ #define FTDI_TURTELIZER_PID 0xBDC8 /* JTAG/RS-232 adapter by egnite GmBH */ +/* + * GN Otometrics (http://www.otometrics.com) + * Submitted by Ville Sundberg. + */ +#define GN_OTOMETRICS_VID 0x0c33 /* Vendor ID */ +#define AURICAL_USB_PID 0x0010 /* Aurical USB Audiometer */ + /* * BmRequestType: 1100 0000b * bRequest: FTDI_E2_READ -- GitLab From 8bf16ba7c8ea9d067914e270764c14020a26232f Mon Sep 17 00:00:00 2001 From: Craig Shelley Date: Sun, 12 Jul 2009 21:52:33 +0100 Subject: [PATCH 0422/1342] USB: CP210x Add new device IDs Signed-off-by: Craig Shelley Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/cp210x.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c index e9a40b820fd..985cbcf48bd 100644 --- a/drivers/usb/serial/cp210x.c +++ b/drivers/usb/serial/cp210x.c @@ -80,6 +80,7 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(0x10C4, 0x80F6) }, /* Suunto sports instrument */ { USB_DEVICE(0x10C4, 0x8115) }, /* Arygon NFC/Mifare Reader */ { USB_DEVICE(0x10C4, 0x813D) }, /* Burnside Telecom Deskmobile */ + { USB_DEVICE(0x10C4, 0x813F) }, /* Tams Master Easy Control */ { USB_DEVICE(0x10C4, 0x814A) }, /* West Mountain Radio RIGblaster P&P */ { USB_DEVICE(0x10C4, 0x814B) }, /* West Mountain Radio RIGtalk */ { USB_DEVICE(0x10C4, 0x815E) }, /* Helicomm IP-Link 1220-DVM */ @@ -96,7 +97,9 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(0x10c4, 0x8293) }, /* Telegesys ETRX2USB */ { USB_DEVICE(0x10C4, 0x82F9) }, /* Procyon AVS */ { USB_DEVICE(0x10C4, 0x8341) }, /* Siemens MC35PU GPRS Modem */ + { USB_DEVICE(0x10C4, 0x8382) }, /* Cygnal Integrated Products, Inc. */ { USB_DEVICE(0x10C4, 0x83A8) }, /* Amber Wireless AMB2560 */ + { USB_DEVICE(0x10C4, 0x8411) }, /* Kyocera GPS Module */ { USB_DEVICE(0x10C4, 0x846E) }, /* BEI USB Sensor Interface (VCP) */ { USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */ { USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */ -- GitLab From bcfa4e68d8d0ea617bde4203b2b3848f5a49a423 Mon Sep 17 00:00:00 2001 From: Simon Kagstrom Date: Mon, 13 Jul 2009 08:25:09 +0200 Subject: [PATCH 0423/1342] USB: ehci-orion: Call ehci_reset before ehci_halt I noticed that USB initialization didn't setup correctly on my kirkwood based board (OpenRD base) if I hadn't initialized USB in U-boot first. The error message looks like this: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver orion-ehci orion-ehci.0: Marvell Orion EHCI orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 orion-ehci orion-ehci.0: can't setup orion-ehci orion-ehci.0: USB bus 1 deregistered orion-ehci orion-ehci.0: init orion-ehci.0 fail, -110 orion-ehci: probe of orion-ehci.0 failed with error -110 which is caused by ehci_halt() timing out in the handshake() call. I noticed that U-boot does a reset before calling handshake(), so this patch does the same thing for Linux. USB now works for me. Signed-off-by: Simon Kagstrom Acked-by: Nicolas Pitre Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-orion.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/host/ehci-orion.c b/drivers/usb/host/ehci-orion.c index dc2ac613a9d..1d283e1b2b8 100644 --- a/drivers/usb/host/ehci-orion.c +++ b/drivers/usb/host/ehci-orion.c @@ -105,6 +105,7 @@ static int ehci_orion_setup(struct usb_hcd *hcd) struct ehci_hcd *ehci = hcd_to_ehci(hcd); int retval; + ehci_reset(ehci); retval = ehci_halt(ehci); if (retval) return retval; @@ -118,7 +119,6 @@ static int ehci_orion_setup(struct usb_hcd *hcd) hcd->has_tt = 1; - ehci_reset(ehci); ehci_port_power(ehci, 0); return retval; -- GitLab From c420befde6b2747ebc2b8f015687a5dbd6e167ca Mon Sep 17 00:00:00 2001 From: Herton Ronaldo Krzesinski Date: Wed, 15 Jul 2009 17:10:26 -0300 Subject: [PATCH 0424/1342] USB: option: add ZTE device ids and remove ONDA ids Current listed Onda ids are ZTE devices. Replace them with ZTE id define and add more ZTE device ids. Also remove 19d2:2000, this is the id when device is first plugged in and is a CD-only device, before the switch using eject. These changes are based on a previous patch by Ming Zhao Signed-off-by: Herton Ronaldo Krzesinski Cc: Ming Zhao Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 113 ++++++++++++++++++++++-------------- 1 file changed, 68 insertions(+), 45 deletions(-) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 7638d2632ff..5640f38fdb3 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -261,11 +261,6 @@ static int option_resume(struct usb_serial *serial); #define AXESSTEL_VENDOR_ID 0x1726 #define AXESSTEL_PRODUCT_MV110H 0x1000 -#define ONDA_VENDOR_ID 0x19d2 -#define ONDA_PRODUCT_MSA501HS 0x0001 -#define ONDA_PRODUCT_ET502HS 0x0002 -#define ONDA_PRODUCT_MT503HS 0x2000 - #define BANDRICH_VENDOR_ID 0x1A8D #define BANDRICH_PRODUCT_C100_1 0x1002 #define BANDRICH_PRODUCT_C100_2 0x1003 @@ -476,42 +471,6 @@ static struct usb_device_id option_ids[] = { { USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_500A) }, { USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_620UW) }, { USB_DEVICE(AXESSTEL_VENDOR_ID, AXESSTEL_PRODUCT_MV110H) }, - { USB_DEVICE(ONDA_VENDOR_ID, ONDA_PRODUCT_MSA501HS) }, - { USB_DEVICE(ONDA_VENDOR_ID, ONDA_PRODUCT_ET502HS) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0003) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0004) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0005) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0006) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0007) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0008) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0009) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x000a) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x000b) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x000c) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x000d) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x000e) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x000f) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0010) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0011) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0012) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0013) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0014) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0015) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0016) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0017) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0018) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0019) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0020) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0021) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0022) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0023) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0024) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0025) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0026) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0027) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0028) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0029) }, - { USB_DEVICE(ONDA_VENDOR_ID, ONDA_PRODUCT_MT503HS) }, { USB_DEVICE(YISO_VENDOR_ID, YISO_PRODUCT_U893) }, { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_C100_1) }, { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_C100_2) }, @@ -536,10 +495,74 @@ static struct usb_device_id option_ids[] = { { USB_DEVICE(QUALCOMM_VENDOR_ID, 0x6613)}, /* Onda H600/ZTE MF330 */ { USB_DEVICE(MAXON_VENDOR_ID, 0x6280) }, /* BP3-USB & BP3-EXT HSDPA */ { USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_UC864E) }, - { USB_DEVICE(ZTE_VENDOR_ID, ZTE_PRODUCT_MF622) }, - { USB_DEVICE(ZTE_VENDOR_ID, ZTE_PRODUCT_MF626) }, - { USB_DEVICE(ZTE_VENDOR_ID, ZTE_PRODUCT_MF628) }, - { USB_DEVICE(ZTE_VENDOR_ID, ZTE_PRODUCT_CDMA_TECH) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MF622, 0xff, 0xff, 0xff) }, /* ZTE WCDMA products */ + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0002, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0003, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0004, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0005, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0006, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0007, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0008, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0009, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x000a, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x000b, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x000c, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x000d, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x000e, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x000f, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0010, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0011, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0012, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0013, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MF628, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0016, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0017, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0018, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0019, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0020, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0021, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0022, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0023, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0024, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0025, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0026, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0028, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0029, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0030, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MF626, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0032, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0033, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0037, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0039, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0042, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0043, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0048, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0049, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0051, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0052, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0054, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0055, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0057, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0058, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0061, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0062, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0063, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0064, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0066, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0069, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0076, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0078, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0082, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0086, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x2002, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x2003, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0014, 0xff, 0xff, 0xff) }, /* ZTE CDMA products */ + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0027, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0059, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0060, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0070, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0073, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_CDMA_TECH, 0xff, 0xff, 0xff) }, { USB_DEVICE(BENQ_VENDOR_ID, BENQ_PRODUCT_H10) }, { USB_DEVICE(DLINK_VENDOR_ID, DLINK_PRODUCT_DWM_652) }, { USB_DEVICE(QISDA_VENDOR_ID, QISDA_PRODUCT_H21_4512) }, -- GitLab From f1469fc3ef1d5a8a67146c1c72021f012a59dea6 Mon Sep 17 00:00:00 2001 From: Tim Gardner Date: Fri, 17 Jul 2009 07:55:36 -0600 Subject: [PATCH 0425/1342] USB: option: Add USB ID for Novatel MC727/U727/USB727 refresh BugLink: https://bugs.launchpad.net/bugs/365291 Signed-off-by: Tim Gardner Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 5640f38fdb3..ff61f89918e 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -207,6 +207,7 @@ static int option_resume(struct usb_serial *serial); #define NOVATELWIRELESS_PRODUCT_MC727 0x4100 #define NOVATELWIRELESS_PRODUCT_MC950D 0x4400 #define NOVATELWIRELESS_PRODUCT_U727 0x5010 +#define NOVATELWIRELESS_PRODUCT_MC727_NEW 0x5100 #define NOVATELWIRELESS_PRODUCT_MC760 0x6000 #define NOVATELWIRELESS_PRODUCT_OVMC760 0x6002 @@ -435,6 +436,7 @@ static struct usb_device_id option_ids[] = { { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_EU870D) }, /* Novatel EU850D/EU860D/EU870D */ { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_MC950D) }, /* Novatel MC930D/MC950D */ { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_MC727) }, /* Novatel MC727/U727/USB727 */ + { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_MC727_NEW) }, /* Novatel MC727/U727/USB727 refresh */ { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_U727) }, /* Novatel MC727/U727/USB727 */ { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_MC760) }, /* Novatel MC760/U760/USB760 */ { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_OVMC760) }, /* Novatel Ovation MC760 */ -- GitLab From 9d498beafc0a66ce333f0d9067af0aa5dedd4c8e Mon Sep 17 00:00:00 2001 From: Russell Lang Date: Fri, 17 Jul 2009 19:29:20 +1000 Subject: [PATCH 0426/1342] USB: aten uc2324 is really a moschip 7840 I've opened up the case, and the chips in the ATEN UC2324 are: Moschip MCS7840CV-AA 69507-6B1 0650 (USB to 4-port serial) (logo with AF kerned together) 0748 24BC02 SINGLP (unknown 8-pin chip) (logo looks like 3 or Z in circle) ZT3243LEEA 0752 B7A16420.T (4 chips, so this will be RS232 line driver) (Probably equivalent of Sipex SP3243) So the ATEN 2324 (aten2011.c driver), is definitely the Moschip 7840, and should use the mos7840.c driver. I expect you will remove the aten2011.c driver from the staging area. From the aten2011.c source code, the device ID for the UC2322 (2 port serial) is 0x7820, just like the Moschip evaluation board. This value should be added to the device id table of mos7840.c. Here's a patch that adds these devices to the driver. From: Russell Lang Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/mos7840.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) diff --git a/drivers/usb/serial/mos7840.c b/drivers/usb/serial/mos7840.c index c31940a307f..270009afdf7 100644 --- a/drivers/usb/serial/mos7840.c +++ b/drivers/usb/serial/mos7840.c @@ -124,10 +124,13 @@ #define BANDB_DEVICE_ID_USOPTL4_4 0xAC44 #define BANDB_DEVICE_ID_USOPTL4_2 0xAC42 -/* This driver also supports the ATEN UC2324 device since it is mos7840 based - * - if I knew the device id it would also support the ATEN UC2322 */ +/* This driver also supports + * ATEN UC2324 device using Moschip MCS7840 + * ATEN UC2322 device using Moschip MCS7820 + */ #define USB_VENDOR_ID_ATENINTL 0x0557 #define ATENINTL_DEVICE_ID_UC2324 0x2011 +#define ATENINTL_DEVICE_ID_UC2322 0x7820 /* Interrupt Routine Defines */ @@ -177,6 +180,7 @@ static struct usb_device_id moschip_port_id_table[] = { {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_4)}, {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_2)}, {USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2324)}, + {USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2322)}, {} /* terminating entry */ }; @@ -186,6 +190,7 @@ static __devinitdata struct usb_device_id moschip_id_table_combined[] = { {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_4)}, {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_2)}, {USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2324)}, + {USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2322)}, {} /* terminating entry */ }; -- GitLab From 183791588efd416fc35a71819683b32dee92615b Mon Sep 17 00:00:00 2001 From: Peng Huang Date: Wed, 22 Jul 2009 11:54:48 +0200 Subject: [PATCH 0427/1342] USB: serial: option: Add ZTE AC8710 usb modem device. Signed-off-by: Peng Huang Cc: Jiri Kosina Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index ff61f89918e..b6de085bc78 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -299,6 +299,7 @@ static int option_resume(struct usb_serial *serial); #define ZTE_PRODUCT_MF628 0x0015 #define ZTE_PRODUCT_MF626 0x0031 #define ZTE_PRODUCT_CDMA_TECH 0xfffe +#define ZTE_PRODUCT_AC8710 0xfff1 #define BENQ_VENDOR_ID 0x04a5 #define BENQ_PRODUCT_H10 0x4068 @@ -565,6 +566,7 @@ static struct usb_device_id option_ids[] = { { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0070, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0073, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_CDMA_TECH, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC8710, 0xff, 0xff, 0xff) }, { USB_DEVICE(BENQ_VENDOR_ID, BENQ_PRODUCT_H10) }, { USB_DEVICE(DLINK_VENDOR_ID, DLINK_PRODUCT_DWM_652) }, { USB_DEVICE(QISDA_VENDOR_ID, QISDA_PRODUCT_H21_4512) }, -- GitLab From 48c348cc939aaa3a07d4938669f2f315152e895e Mon Sep 17 00:00:00 2001 From: Javier Martin Date: Thu, 23 Jul 2009 04:03:43 +0200 Subject: [PATCH 0428/1342] USB: option.c to support Alcatel X060S/X200 broadband modems Added support for the Alcatel X060S/X200 broadband modems to the option driver. The device starts in cd-rom emulation mode (1bbb:f000) and requires the use of the usb_modeswitch tool to switch it to modem mode (1bbb:0000). Signed-off-by: Javier Martin Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index b6de085bc78..c784ddbe7b6 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -321,6 +321,11 @@ static int option_resume(struct usb_serial *serial); #define ALINK_VENDOR_ID 0x1e0e #define ALINK_PRODUCT_3GU 0x9200 +/* ALCATEL PRODUCTS */ +#define ALCATEL_VENDOR_ID 0x1bbb +#define ALCATEL_PRODUCT_X060S 0x0000 + + static struct usb_device_id option_ids[] = { { USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_COLT) }, { USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_RICOLA) }, @@ -576,6 +581,7 @@ static struct usb_device_id option_ids[] = { { USB_DEVICE(TOSHIBA_VENDOR_ID, TOSHIBA_PRODUCT_HSDPA_MINICARD ) }, /* Toshiba 3G HSDPA == Novatel Expedite EU870D MiniCard */ { USB_DEVICE(ALINK_VENDOR_ID, 0x9000) }, { USB_DEVICE_AND_INTERFACE_INFO(ALINK_VENDOR_ID, ALINK_PRODUCT_3GU, 0xff, 0xff, 0xff) }, + { USB_DEVICE(ALCATEL_VENDOR_ID, ALCATEL_PRODUCT_X060S) }, { } /* Terminating entry */ }; MODULE_DEVICE_TABLE(usb, option_ids); -- GitLab From f01b017d198486ee3553bee6841f788263cf2c23 Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Fri, 17 Jul 2009 17:30:03 +0300 Subject: [PATCH 0429/1342] USB: musb_gadget_ep0: fix typo in service_zero_data_request() This function uses wrong bit mask to prevent clearing RXCSR status bits when halting an endpoint -- which results in clearing SentStall and RxPktRdy bits (that the code actually tries to avoid); must be a result of cut-and-paste... Signed-off-by: Sergei Shtylyov Acked-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/musb/musb_gadget_ep0.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/musb/musb_gadget_ep0.c b/drivers/usb/musb/musb_gadget_ep0.c index 40ed50ecedf..7a6778675ad 100644 --- a/drivers/usb/musb/musb_gadget_ep0.c +++ b/drivers/usb/musb/musb_gadget_ep0.c @@ -407,7 +407,7 @@ stall: csr |= MUSB_RXCSR_P_SENDSTALL | MUSB_RXCSR_FLUSHFIFO | MUSB_RXCSR_CLRDATATOG - | MUSB_TXCSR_P_WZC_BITS; + | MUSB_RXCSR_P_WZC_BITS; musb_writew(regs, MUSB_RXCSR, csr); } -- GitLab From 3a9f5bd82dc986d496d8484ff54b107b4515f43f Mon Sep 17 00:00:00 2001 From: Amit Kucheria Date: Mon, 27 Jul 2009 12:03:19 +0300 Subject: [PATCH 0430/1342] USB: musb: Refer to musb_otg_timer_func under correct #ifdef musb_otg_timer_func() is defined under #ifdef CONFIG_USB_MUSB_OTG. Make sure any reference to it is also under the same #ifdef. Without this fix, the driver failes to compile when USB_OTG is defined but USB_MUSB_OTG isn't. Signed-off-by: Amit Kucheria Cc: Felipe Balbi Cc: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/musb/musb_core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c index 554a414f65d..642a4e25f7d 100644 --- a/drivers/usb/musb/musb_core.c +++ b/drivers/usb/musb/musb_core.c @@ -1990,7 +1990,7 @@ bad_config: if (status < 0) goto fail2; -#ifdef CONFIG_USB_OTG +#ifdef CONFIG_USB_MUSB_OTG setup_timer(&musb->otg_timer, musb_otg_timer_func, (unsigned long) musb); #endif -- GitLab From 2bbff7b742d55b094ed1467702efe146cd60c64f Mon Sep 17 00:00:00 2001 From: Ajay Kumar Gupta Date: Mon, 27 Jul 2009 14:32:15 -0700 Subject: [PATCH 0431/1342] USB: musb: fix CONFIGDATA register read issue INDEX register has to be set to '0' before reading CONFIGDATA register which is only present in TI musb platforms. Currently the default register access mode is set to FLAT_MODE thus INDEX register is not getting set properly with musb_ep_select() which is just a nop operation in FLAT_MODE.This invalid register read is causing module reinset failure. Fixing the issue by moving INDEX register write part to musb_read_configdata() function itself. Signed-off-by: Vikram Pandita Signed-off-by: Anand Gadiyar Signed-off-by: Ajay Kumar Gupta Acked-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/musb/musb_core.c | 1 - drivers/usb/musb/musb_regs.h | 1 + 2 files changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c index 642a4e25f7d..c7c1ca0494c 100644 --- a/drivers/usb/musb/musb_core.c +++ b/drivers/usb/musb/musb_core.c @@ -1326,7 +1326,6 @@ static int __init musb_core_init(u16 musb_type, struct musb *musb) int i; /* log core options (read using indexed model) */ - musb_ep_select(mbase, 0); reg = musb_read_configdata(mbase); strcpy(aInfo, (reg & MUSB_CONFIGDATA_UTMIDW) ? "UTMI-16" : "UTMI-8"); diff --git a/drivers/usb/musb/musb_regs.h b/drivers/usb/musb/musb_regs.h index de3b2f18db4..fbfd3fd9ce1 100644 --- a/drivers/usb/musb/musb_regs.h +++ b/drivers/usb/musb/musb_regs.h @@ -323,6 +323,7 @@ static inline void musb_write_rxfifoadd(void __iomem *mbase, u16 c_off) static inline u8 musb_read_configdata(void __iomem *mbase) { + musb_writeb(mbase, MUSB_INDEX, 0); return musb_readb(mbase, 0x10 + MUSB_CONFIGDATA); } -- GitLab From 0f157ef3a1284f41d9804ecb87fdcc8ea946b9fa Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Tue, 28 Jul 2009 11:56:17 -0400 Subject: [PATCH 0432/1342] USB: usbtest: no need for USB_DEVICEFS THis patch (as1270) allows the usbtest module to be built even when USB_DEVICEFS isn't configured. Tests can be performed without USB_DEVICEFS, using the /dev/bus/usb/*/* device files. Signed-off-by: Alan Stern Signed-off-by: Greg Kroah-Hartman --- drivers/usb/misc/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig index a68d91a11be..abe3aa67ed0 100644 --- a/drivers/usb/misc/Kconfig +++ b/drivers/usb/misc/Kconfig @@ -220,7 +220,7 @@ config USB_IOWARRIOR config USB_TEST tristate "USB testing driver" - depends on USB && USB_DEVICEFS + depends on USB help This driver is for testing host controller software. It is used with specialized device firmware for regression and stress testing, -- GitLab From d8f1a5ed52a81a953918d4aebe185ba008a7be34 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Mon, 13 Jul 2009 00:23:47 +0200 Subject: [PATCH 0433/1342] USB: xhci: fix less- and greater than confusion Without this change the loops won't start Signed-off-by: Roel Kluin Cc: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-dbg.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/usb/host/xhci-dbg.c b/drivers/usb/host/xhci-dbg.c index 2501c571f85..56032f2d84e 100644 --- a/drivers/usb/host/xhci-dbg.c +++ b/drivers/usb/host/xhci-dbg.c @@ -419,7 +419,7 @@ void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_ad &ctx->add_flags, (unsigned long long)dma, ctx->add_flags); dma += field_size; - for (i = 0; i > 6; ++i) { + for (i = 0; i < 6; ++i) { xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n", &ctx->rsvd[i], (unsigned long long)dma, ctx->rsvd[i], i); @@ -443,7 +443,7 @@ void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_ad &ctx->slot.dev_state, (unsigned long long)dma, ctx->slot.dev_state); dma += field_size; - for (i = 0; i > 4; ++i) { + for (i = 0; i < 4; ++i) { xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n", &ctx->slot.reserved[i], (unsigned long long)dma, ctx->slot.reserved[i], i); -- GitLab From f9dc68fe7ad390428c6bc5d7ff582cdb5d92fcb8 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:03:07 -0700 Subject: [PATCH 0434/1342] USB: xhci: Set TD size in transfer TRB. The 0.95 xHCI specification requires software to set the "TD size" field in each transaction request block (TRB). This field gives the host controller an indication of how much data is remaining in the TD (including the buffer in the current TRB). Set this field in bulk TRBs and data stage TRBs for control transfers. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-ring.c | 20 +++++++++++++++----- 1 file changed, 15 insertions(+), 5 deletions(-) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 02d81985c45..d5b95299742 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -1285,6 +1285,7 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags, /* Queue the first TRB, even if it's zero-length */ do { u32 field = 0; + u32 length_field = 0; /* Don't change the cycle bit of the first TRB until later */ if (first_trb) @@ -1314,10 +1315,13 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags, (unsigned int) (addr + TRB_MAX_BUFF_SIZE) & ~(TRB_MAX_BUFF_SIZE - 1), (unsigned int) addr + trb_buff_len); } + length_field = TRB_LEN(trb_buff_len) | + TD_REMAINDER(urb->transfer_buffer_length - running_total) | + TRB_INTR_TARGET(0); queue_trb(xhci, ep_ring, false, (u32) addr, (u32) ((u64) addr >> 32), - TRB_LEN(trb_buff_len) | TRB_INTR_TARGET(0), + length_field, /* We always want to know if the TRB was short, * or we won't get an event when it completes. * (Unless we use event data TRBs, which are a @@ -1365,7 +1369,7 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, struct xhci_generic_trb *start_trb; bool first_trb; int start_cycle; - u32 field; + u32 field, length_field; int running_total, trb_buff_len, ret; u64 addr; @@ -1443,10 +1447,13 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, td->last_trb = ep_ring->enqueue; field |= TRB_IOC; } + length_field = TRB_LEN(trb_buff_len) | + TD_REMAINDER(urb->transfer_buffer_length - running_total) | + TRB_INTR_TARGET(0); queue_trb(xhci, ep_ring, false, (u32) addr, (u32) ((u64) addr >> 32), - TRB_LEN(trb_buff_len) | TRB_INTR_TARGET(0), + length_field, /* We always want to know if the TRB was short, * or we won't get an event when it completes. * (Unless we use event data TRBs, which are a @@ -1478,7 +1485,7 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags, struct usb_ctrlrequest *setup; struct xhci_generic_trb *start_trb; int start_cycle; - u32 field; + u32 field, length_field; struct xhci_td *td; ep_ring = xhci->devs[slot_id]->ep_rings[ep_index]; @@ -1528,13 +1535,16 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags, /* If there's data, queue data TRBs */ field = 0; + length_field = TRB_LEN(urb->transfer_buffer_length) | + TD_REMAINDER(urb->transfer_buffer_length) | + TRB_INTR_TARGET(0); if (urb->transfer_buffer_length > 0) { if (setup->bRequestType & USB_DIR_IN) field |= TRB_DIR_IN; queue_trb(xhci, ep_ring, false, lower_32_bits(urb->transfer_dma), upper_32_bits(urb->transfer_dma), - TRB_LEN(urb->transfer_buffer_length) | TRB_INTR_TARGET(0), + length_field, /* Event on short tx */ field | TRB_ISP | TRB_TYPE(TRB_DATA) | ep_ring->cycle_state); } -- GitLab From a1587d97ce3e53816c88b513a2038f6c5e5babd7 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:03:15 -0700 Subject: [PATCH 0435/1342] USB: xhci: Deal with stalled endpoints. When an endpoint on a device under an xHCI host controller stalls, the host controller driver must let the hardware know that the USB core has successfully cleared the halt condition. The HCD submits a Reset Endpoint Command, which will clear the toggle bit for USB 2.0 devices, and set the sequence number to zero for USB 3.0 devices. The xHCI urb_enqueue will accept new URBs while the endpoint is halted, and will queue them to the hardware rings. However, the endpoint doorbell will not be rung until the Reset Endpoint Command completes. Don't queue a reset endpoint command for root hubs. khubd clears halt conditions on the roothub during the initialization process, but the roothub isn't a real device, so the xHCI host controller doesn't need to know about the cleared halt. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-hcd.c | 44 +++++++++++++++++++++++++++++++++++- drivers/usb/host/xhci-pci.c | 1 + drivers/usb/host/xhci-ring.c | 36 ++++++++++++++++++++++++++++- drivers/usb/host/xhci.h | 8 +++++-- 4 files changed, 85 insertions(+), 4 deletions(-) diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index dba3e07ccd0..1c5901ad6eb 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -787,8 +787,11 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, int ret = 0; ret = xhci_check_args(hcd, udev, ep, 1, __func__); - if (ret <= 0) + if (ret <= 0) { + /* So we won't queue a reset ep command for a root hub */ + ep->hcpriv = NULL; return ret; + } xhci = hcd_to_xhci(hcd); added_ctxs = xhci_get_endpoint_flag(&ep->desc); @@ -851,6 +854,9 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, } new_slot_info = in_ctx->slot.dev_info; + /* Store the usb_device pointer for later use */ + ep->hcpriv = udev; + xhci_dbg(xhci, "add ep 0x%x, slot id %d, new drop flags = %#x, new add flags = %#x, new slot info = %#x\n", (unsigned int) ep->desc.bEndpointAddress, udev->slot_id, @@ -1026,6 +1032,42 @@ void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev) xhci_zero_in_ctx(virt_dev); } +/* Deal with stalled endpoints. The core should have sent the control message + * to clear the halt condition. However, we need to make the xHCI hardware + * reset its sequence number, since a device will expect a sequence number of + * zero after the halt condition is cleared. + * Context: in_interrupt + */ +void xhci_endpoint_reset(struct usb_hcd *hcd, + struct usb_host_endpoint *ep) +{ + struct xhci_hcd *xhci; + struct usb_device *udev; + unsigned int ep_index; + unsigned long flags; + int ret; + + xhci = hcd_to_xhci(hcd); + udev = (struct usb_device *) ep->hcpriv; + /* Called with a root hub endpoint (or an endpoint that wasn't added + * with xhci_add_endpoint() + */ + if (!ep->hcpriv) + return; + ep_index = xhci_get_endpoint_index(&ep->desc); + + xhci_dbg(xhci, "Queueing reset endpoint command\n"); + spin_lock_irqsave(&xhci->lock, flags); + ret = xhci_queue_reset_ep(xhci, udev->slot_id, ep_index); + if (!ret) { + xhci_ring_cmd_db(xhci); + } + spin_unlock_irqrestore(&xhci->lock, flags); + + if (ret) + xhci_warn(xhci, "FIXME allocate a new ring segment\n"); +} + /* * At this point, the struct usb_device is about to go away, the device has * disconnected, and all traffic has been stopped and the endpoints have been diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c index 1462709e26c..592fe7e623f 100644 --- a/drivers/usb/host/xhci-pci.c +++ b/drivers/usb/host/xhci-pci.c @@ -117,6 +117,7 @@ static const struct hc_driver xhci_pci_hc_driver = { .free_dev = xhci_free_dev, .add_endpoint = xhci_add_endpoint, .drop_endpoint = xhci_drop_endpoint, + .endpoint_reset = xhci_endpoint_reset, .check_bandwidth = xhci_check_bandwidth, .reset_bandwidth = xhci_reset_bandwidth, .address_device = xhci_address_device, diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index d5b95299742..d672ba14ff8 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -279,7 +279,8 @@ static void ring_ep_doorbell(struct xhci_hcd *xhci, /* Don't ring the doorbell for this endpoint if there are pending * cancellations because the we don't want to interrupt processing. */ - if (!ep_ring->cancels_pending && !(ep_ring->state & SET_DEQ_PENDING)) { + if (!ep_ring->cancels_pending && !(ep_ring->state & SET_DEQ_PENDING) + && !(ep_ring->state & EP_HALTED)) { field = xhci_readl(xhci, db_addr) & DB_MASK; xhci_writel(xhci, field | EPI_TO_DB(ep_index), db_addr); /* Flush PCI posted writes - FIXME Matthew Wilcox says this @@ -603,6 +604,25 @@ static void handle_set_deq_completion(struct xhci_hcd *xhci, ring_ep_doorbell(xhci, slot_id, ep_index); } +static void handle_reset_ep_completion(struct xhci_hcd *xhci, + struct xhci_event_cmd *event, + union xhci_trb *trb) +{ + int slot_id; + unsigned int ep_index; + + slot_id = TRB_TO_SLOT_ID(trb->generic.field[3]); + ep_index = TRB_TO_EP_INDEX(trb->generic.field[3]); + /* This command will only fail if the endpoint wasn't halted, + * but we don't care. + */ + xhci_dbg(xhci, "Ignoring reset ep completion code of %u\n", + (unsigned int) GET_COMP_CODE(event->status)); + + /* Clear our internal halted state and restart the ring */ + xhci->devs[slot_id]->ep_rings[ep_index]->state &= ~EP_HALTED; + ring_ep_doorbell(xhci, slot_id, ep_index); +} static void handle_cmd_completion(struct xhci_hcd *xhci, struct xhci_event_cmd *event) @@ -653,6 +673,9 @@ static void handle_cmd_completion(struct xhci_hcd *xhci, case TRB_TYPE(TRB_CMD_NOOP): ++xhci->noops_handled; break; + case TRB_TYPE(TRB_RESET_EP): + handle_reset_ep_completion(xhci, event, xhci->cmd_ring->dequeue); + break; default: /* Skip over unknown commands on the event ring */ xhci->error_bitmask |= 1 << 6; @@ -823,6 +846,7 @@ static int handle_tx_event(struct xhci_hcd *xhci, break; case COMP_STALL: xhci_warn(xhci, "WARN: Stalled endpoint\n"); + ep_ring->state |= EP_HALTED; status = -EPIPE; break; case COMP_TRB_ERR: @@ -1656,3 +1680,13 @@ static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id, return queue_command(xhci, (u32) addr | cycle_state, 0, 0, trb_slot_id | trb_ep_index | type); } + +int xhci_queue_reset_ep(struct xhci_hcd *xhci, int slot_id, + unsigned int ep_index) +{ + u32 trb_slot_id = SLOT_ID_FOR_TRB(slot_id); + u32 trb_ep_index = EP_ID_FOR_TRB(ep_index); + u32 type = TRB_TYPE(TRB_RESET_EP); + + return queue_command(xhci, 0, 0, 0, trb_slot_id | trb_ep_index | type); +} diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 8936eeb5588..cde648a524f 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -848,8 +848,8 @@ union xhci_trb { #define TRB_CONFIG_EP 12 /* Evaluate Context Command */ #define TRB_EVAL_CONTEXT 13 -/* Reset Transfer Ring Command */ -#define TRB_RESET_RING 14 +/* Reset Endpoint Command */ +#define TRB_RESET_EP 14 /* Stop Transfer Ring Command */ #define TRB_STOP_RING 15 /* Set Transfer Ring Dequeue Pointer Command */ @@ -929,6 +929,7 @@ struct xhci_ring { unsigned int cancels_pending; unsigned int state; #define SET_DEQ_PENDING (1 << 0) +#define EP_HALTED (1 << 1) /* The TRB that was last reported in a stopped endpoint ring */ union xhci_trb *stopped_trb; struct xhci_td *stopped_td; @@ -1128,6 +1129,7 @@ int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags); int xhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status); int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, struct usb_host_endpoint *ep); int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev, struct usb_host_endpoint *ep); +void xhci_endpoint_reset(struct usb_hcd *hcd, struct usb_host_endpoint *ep); int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev); void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev); @@ -1148,6 +1150,8 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, struct urb *urb, int slot_id, unsigned int ep_index); int xhci_queue_configure_endpoint(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr, u32 slot_id); +int xhci_queue_reset_ep(struct xhci_hcd *xhci, int slot_id, + unsigned int ep_index); /* xHCI roothub code */ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, u16 wIndex, -- GitLab From b11069f5f6ce6e359f853e908b0917303fcdec8f Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:03:23 -0700 Subject: [PATCH 0436/1342] USB: xhci: Use GFP_ATOMIC while holding spinlocks. The xHCI functions to queue an URB onto the hardware rings must be called with the xhci spinlock held. Those functions will allocate memory, and take a gfp_t memory flags argument. We must pass them the GFP_ATOMIC flag, since we don't want the memory allocation to attempt to sleep while waiting for more memory to become available. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-hcd.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index 1c5901ad6eb..ff99365cae4 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -601,10 +601,13 @@ int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags) goto exit; } if (usb_endpoint_xfer_control(&urb->ep->desc)) - ret = xhci_queue_ctrl_tx(xhci, mem_flags, urb, + /* We have a spinlock and interrupts disabled, so we must pass + * atomic context to this function, which may allocate memory. + */ + ret = xhci_queue_ctrl_tx(xhci, GFP_ATOMIC, urb, slot_id, ep_index); else if (usb_endpoint_xfer_bulk(&urb->ep->desc)) - ret = xhci_queue_bulk_tx(xhci, mem_flags, urb, + ret = xhci_queue_bulk_tx(xhci, GFP_ATOMIC, urb, slot_id, ep_index); else ret = -EINVAL; -- GitLab From 8e595a5d30a5ee4bb745d4da6439d73ed7d91054 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:03:31 -0700 Subject: [PATCH 0437/1342] USB: xhci: Represent 64-bit addresses with one u64. There are several xHCI data structures that use two 32-bit fields to represent a 64-bit address. Since some architectures don't support 64-bit PCI writes, the fields need to be written in two 32-bit writes. The xHCI specification says that if a platform is incapable of generating 64-bit writes, software must write the low 32-bits first, then the high 32-bits. Hardware that supports 64-bit addressing will wait for the high 32-bit write before reading the revised value, and hardware that only supports 32-bit writes will ignore the high 32-bit write. Previous xHCI code represented 64-bit addresses with two u32 values. This lead to buggy code that would write the 32-bits in the wrong order, or forget to write the upper 32-bits. Change the two u32s to one u64 and create a function call to write all 64-bit addresses in the proper order. This new function could be modified in the future if all platforms support 64-bit writes. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-dbg.c | 67 ++++++++++++++---------------------- drivers/usb/host/xhci-hcd.c | 43 ++++++++++------------- drivers/usb/host/xhci-mem.c | 61 +++++++++++++------------------- drivers/usb/host/xhci-ring.c | 49 +++++++++++++------------- drivers/usb/host/xhci.h | 65 +++++++++++++++++++++++----------- 5 files changed, 137 insertions(+), 148 deletions(-) diff --git a/drivers/usb/host/xhci-dbg.c b/drivers/usb/host/xhci-dbg.c index 56032f2d84e..6d62e4abe3c 100644 --- a/drivers/usb/host/xhci-dbg.c +++ b/drivers/usb/host/xhci-dbg.c @@ -173,6 +173,7 @@ void xhci_print_ir_set(struct xhci_hcd *xhci, struct xhci_intr_reg *ir_set, int { void *addr; u32 temp; + u64 temp_64; addr = &ir_set->irq_pending; temp = xhci_readl(xhci, addr); @@ -200,25 +201,15 @@ void xhci_print_ir_set(struct xhci_hcd *xhci, struct xhci_intr_reg *ir_set, int xhci_dbg(xhci, " WARN: %p: ir_set.rsvd = 0x%x\n", addr, (unsigned int)temp); - addr = &ir_set->erst_base[0]; - temp = xhci_readl(xhci, addr); - xhci_dbg(xhci, " %p: ir_set.erst_base[0] = 0x%x\n", - addr, (unsigned int) temp); - - addr = &ir_set->erst_base[1]; - temp = xhci_readl(xhci, addr); - xhci_dbg(xhci, " %p: ir_set.erst_base[1] = 0x%x\n", - addr, (unsigned int) temp); - - addr = &ir_set->erst_dequeue[0]; - temp = xhci_readl(xhci, addr); - xhci_dbg(xhci, " %p: ir_set.erst_dequeue[0] = 0x%x\n", - addr, (unsigned int) temp); + addr = &ir_set->erst_base; + temp_64 = xhci_read_64(xhci, addr); + xhci_dbg(xhci, " %p: ir_set.erst_base = @%08llx\n", + addr, temp_64); - addr = &ir_set->erst_dequeue[1]; - temp = xhci_readl(xhci, addr); - xhci_dbg(xhci, " %p: ir_set.erst_dequeue[1] = 0x%x\n", - addr, (unsigned int) temp); + addr = &ir_set->erst_dequeue; + temp_64 = xhci_read_64(xhci, addr); + xhci_dbg(xhci, " %p: ir_set.erst_dequeue = @%08llx\n", + addr, temp_64); } void xhci_print_run_regs(struct xhci_hcd *xhci) @@ -268,8 +259,7 @@ void xhci_debug_trb(struct xhci_hcd *xhci, union xhci_trb *trb) xhci_dbg(xhci, "Link TRB:\n"); xhci_print_trb_offsets(xhci, trb); - address = trb->link.segment_ptr[0] + - (((u64) trb->link.segment_ptr[1]) << 32); + address = trb->link.segment_ptr; xhci_dbg(xhci, "Next ring segment DMA address = 0x%llx\n", address); xhci_dbg(xhci, "Interrupter target = 0x%x\n", @@ -282,8 +272,7 @@ void xhci_debug_trb(struct xhci_hcd *xhci, union xhci_trb *trb) (unsigned int) (trb->link.control & TRB_NO_SNOOP)); break; case TRB_TYPE(TRB_TRANSFER): - address = trb->trans_event.buffer[0] + - (((u64) trb->trans_event.buffer[1]) << 32); + address = trb->trans_event.buffer; /* * FIXME: look at flags to figure out if it's an address or if * the data is directly in the buffer field. @@ -291,8 +280,7 @@ void xhci_debug_trb(struct xhci_hcd *xhci, union xhci_trb *trb) xhci_dbg(xhci, "DMA address or buffer contents= %llu\n", address); break; case TRB_TYPE(TRB_COMPLETION): - address = trb->event_cmd.cmd_trb[0] + - (((u64) trb->event_cmd.cmd_trb[1]) << 32); + address = trb->event_cmd.cmd_trb; xhci_dbg(xhci, "Command TRB pointer = %llu\n", address); xhci_dbg(xhci, "Completion status = %u\n", (unsigned int) GET_COMP_CODE(trb->event_cmd.status)); @@ -328,8 +316,8 @@ void xhci_debug_segment(struct xhci_hcd *xhci, struct xhci_segment *seg) for (i = 0; i < TRBS_PER_SEGMENT; ++i) { trb = &seg->trbs[i]; xhci_dbg(xhci, "@%08x %08x %08x %08x %08x\n", addr, - (unsigned int) trb->link.segment_ptr[0], - (unsigned int) trb->link.segment_ptr[1], + lower_32_bits(trb->link.segment_ptr), + upper_32_bits(trb->link.segment_ptr), (unsigned int) trb->link.intr_target, (unsigned int) trb->link.control); addr += sizeof(*trb); @@ -386,8 +374,8 @@ void xhci_dbg_erst(struct xhci_hcd *xhci, struct xhci_erst *erst) entry = &erst->entries[i]; xhci_dbg(xhci, "@%08x %08x %08x %08x %08x\n", (unsigned int) addr, - (unsigned int) entry->seg_addr[0], - (unsigned int) entry->seg_addr[1], + lower_32_bits(entry->seg_addr), + upper_32_bits(entry->seg_addr), (unsigned int) entry->seg_size, (unsigned int) entry->rsvd); addr += sizeof(*entry); @@ -396,12 +384,13 @@ void xhci_dbg_erst(struct xhci_hcd *xhci, struct xhci_erst *erst) void xhci_dbg_cmd_ptrs(struct xhci_hcd *xhci) { - u32 val; + u64 val; - val = xhci_readl(xhci, &xhci->op_regs->cmd_ring[0]); - xhci_dbg(xhci, "// xHC command ring deq ptr low bits + flags = 0x%x\n", val); - val = xhci_readl(xhci, &xhci->op_regs->cmd_ring[1]); - xhci_dbg(xhci, "// xHC command ring deq ptr high bits = 0x%x\n", val); + val = xhci_read_64(xhci, &xhci->op_regs->cmd_ring); + xhci_dbg(xhci, "// xHC command ring deq ptr low bits + flags = @%08x\n", + lower_32_bits(val)); + xhci_dbg(xhci, "// xHC command ring deq ptr high bits = @%08x\n", + upper_32_bits(val)); } void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep) @@ -462,14 +451,10 @@ void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_ad &ctx->ep[i].ep_info2, (unsigned long long)dma, ctx->ep[i].ep_info2); dma += field_size; - xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - deq[0]\n", - &ctx->ep[i].deq[0], - (unsigned long long)dma, ctx->ep[i].deq[0]); - dma += field_size; - xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - deq[1]\n", - &ctx->ep[i].deq[1], - (unsigned long long)dma, ctx->ep[i].deq[1]); - dma += field_size; + xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08llx - deq\n", + &ctx->ep[i].deq, + (unsigned long long)dma, ctx->ep[i].deq); + dma += 2*field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - tx_info\n", &ctx->ep[i].tx_info, (unsigned long long)dma, ctx->ep[i].tx_info); diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index ff99365cae4..e15773598e4 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -226,6 +226,7 @@ int xhci_init(struct usb_hcd *hcd) static void xhci_work(struct xhci_hcd *xhci) { u32 temp; + u64 temp_64; /* * Clear the op reg interrupt status first, @@ -249,8 +250,8 @@ static void xhci_work(struct xhci_hcd *xhci) xhci_handle_event(xhci); /* Clear the event handler busy flag; the event ring should be empty. */ - temp = xhci_readl(xhci, &xhci->ir_set->erst_dequeue[0]); - xhci_writel(xhci, temp & ~ERST_EHB, &xhci->ir_set->erst_dequeue[0]); + temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); + xhci_write_64(xhci, temp_64 & ~ERST_EHB, &xhci->ir_set->erst_dequeue); /* Flush posted writes -- FIXME is this necessary? */ xhci_readl(xhci, &xhci->ir_set->irq_pending); } @@ -295,6 +296,7 @@ void xhci_event_ring_work(unsigned long arg) { unsigned long flags; int temp; + u64 temp_64; struct xhci_hcd *xhci = (struct xhci_hcd *) arg; int i, j; @@ -311,9 +313,9 @@ void xhci_event_ring_work(unsigned long arg) xhci_dbg(xhci, "Event ring:\n"); xhci_debug_segment(xhci, xhci->event_ring->deq_seg); xhci_dbg_ring_ptrs(xhci, xhci->event_ring); - temp = xhci_readl(xhci, &xhci->ir_set->erst_dequeue[0]); - temp &= ERST_PTR_MASK; - xhci_dbg(xhci, "ERST deq = 0x%x\n", temp); + temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); + temp_64 &= ~ERST_PTR_MASK; + xhci_dbg(xhci, "ERST deq = 64'h%0lx\n", (long unsigned int) temp_64); xhci_dbg(xhci, "Command ring:\n"); xhci_debug_segment(xhci, xhci->cmd_ring->deq_seg); xhci_dbg_ring_ptrs(xhci, xhci->cmd_ring); @@ -356,6 +358,7 @@ void xhci_event_ring_work(unsigned long arg) int xhci_run(struct usb_hcd *hcd) { u32 temp; + u64 temp_64; struct xhci_hcd *xhci = hcd_to_xhci(hcd); void (*doorbell)(struct xhci_hcd *) = NULL; @@ -416,11 +419,9 @@ int xhci_run(struct usb_hcd *hcd) xhci_dbg(xhci, "Event ring:\n"); xhci_debug_ring(xhci, xhci->event_ring); xhci_dbg_ring_ptrs(xhci, xhci->event_ring); - temp = xhci_readl(xhci, &xhci->ir_set->erst_dequeue[0]); - temp &= ERST_PTR_MASK; - xhci_dbg(xhci, "ERST deq = 0x%x\n", temp); - temp = xhci_readl(xhci, &xhci->ir_set->erst_dequeue[1]); - xhci_dbg(xhci, "ERST deq upper = 0x%x\n", temp); + temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); + temp_64 &= ~ERST_PTR_MASK; + xhci_dbg(xhci, "ERST deq = 64'h%0lx\n", (long unsigned int) temp_64); temp = xhci_readl(xhci, &xhci->op_regs->command); temp |= (CMD_RUN); @@ -888,8 +889,7 @@ static void xhci_zero_in_ctx(struct xhci_virt_device *virt_dev) ep_ctx = &virt_dev->in_ctx->ep[i]; ep_ctx->ep_info = 0; ep_ctx->ep_info2 = 0; - ep_ctx->deq[0] = 0; - ep_ctx->deq[1] = 0; + ep_ctx->deq = 0; ep_ctx->tx_info = 0; } } @@ -1165,7 +1165,7 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) struct xhci_virt_device *virt_dev; int ret = 0; struct xhci_hcd *xhci = hcd_to_xhci(hcd); - u32 temp; + u64 temp_64; if (!udev->slot_id) { xhci_dbg(xhci, "Bad Slot ID %d\n", udev->slot_id); @@ -1227,18 +1227,13 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) if (ret) { return ret; } - temp = xhci_readl(xhci, &xhci->op_regs->dcbaa_ptr[0]); - xhci_dbg(xhci, "Op regs DCBAA ptr[0] = %#08x\n", temp); - temp = xhci_readl(xhci, &xhci->op_regs->dcbaa_ptr[1]); - xhci_dbg(xhci, "Op regs DCBAA ptr[1] = %#08x\n", temp); - xhci_dbg(xhci, "Slot ID %d dcbaa entry[0] @%p = %#08x\n", - udev->slot_id, - &xhci->dcbaa->dev_context_ptrs[2*udev->slot_id], - xhci->dcbaa->dev_context_ptrs[2*udev->slot_id]); - xhci_dbg(xhci, "Slot ID %d dcbaa entry[1] @%p = %#08x\n", + temp_64 = xhci_read_64(xhci, &xhci->op_regs->dcbaa_ptr); + xhci_dbg(xhci, "Op regs DCBAA ptr = %#016llx\n", temp_64); + xhci_dbg(xhci, "Slot ID %d dcbaa entry @%p = %#016llx\n", udev->slot_id, - &xhci->dcbaa->dev_context_ptrs[2*udev->slot_id+1], - xhci->dcbaa->dev_context_ptrs[2*udev->slot_id+1]); + &xhci->dcbaa->dev_context_ptrs[udev->slot_id], + (unsigned long long) + xhci->dcbaa->dev_context_ptrs[udev->slot_id]); xhci_dbg(xhci, "Output Context DMA address = %#08llx\n", (unsigned long long)virt_dev->out_ctx_dma); xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id); diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index c8a72de1c50..ec825f16dce 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -88,7 +88,7 @@ static void xhci_link_segments(struct xhci_hcd *xhci, struct xhci_segment *prev, return; prev->next = next; if (link_trbs) { - prev->trbs[TRBS_PER_SEGMENT-1].link.segment_ptr[0] = next->dma; + prev->trbs[TRBS_PER_SEGMENT-1].link.segment_ptr = next->dma; /* Set the last TRB in the segment to have a TRB type ID of Link TRB */ val = prev->trbs[TRBS_PER_SEGMENT-1].link.control; @@ -200,8 +200,7 @@ void xhci_free_virt_device(struct xhci_hcd *xhci, int slot_id) return; dev = xhci->devs[slot_id]; - xhci->dcbaa->dev_context_ptrs[2*slot_id] = 0; - xhci->dcbaa->dev_context_ptrs[2*slot_id + 1] = 0; + xhci->dcbaa->dev_context_ptrs[slot_id] = 0; if (!dev) return; @@ -265,13 +264,12 @@ int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id, * Point to output device context in dcbaa; skip the output control * context, which is eight 32 bit fields (or 32 bytes long) */ - xhci->dcbaa->dev_context_ptrs[2*slot_id] = + xhci->dcbaa->dev_context_ptrs[slot_id] = (u32) dev->out_ctx_dma + (32); xhci_dbg(xhci, "Set slot id %d dcbaa entry %p to 0x%llx\n", slot_id, - &xhci->dcbaa->dev_context_ptrs[2*slot_id], + &xhci->dcbaa->dev_context_ptrs[slot_id], (unsigned long long)dev->out_ctx_dma); - xhci->dcbaa->dev_context_ptrs[2*slot_id + 1] = 0; return 1; fail: @@ -360,10 +358,9 @@ int xhci_setup_addressable_virt_dev(struct xhci_hcd *xhci, struct usb_device *ud ep0_ctx->ep_info2 |= MAX_BURST(0); ep0_ctx->ep_info2 |= ERROR_COUNT(3); - ep0_ctx->deq[0] = + ep0_ctx->deq = dev->ep_rings[0]->first_seg->dma; - ep0_ctx->deq[0] |= dev->ep_rings[0]->cycle_state; - ep0_ctx->deq[1] = 0; + ep0_ctx->deq |= dev->ep_rings[0]->cycle_state; /* Steps 7 and 8 were done in xhci_alloc_virt_device() */ @@ -477,8 +474,7 @@ int xhci_endpoint_init(struct xhci_hcd *xhci, if (!virt_dev->new_ep_rings[ep_index]) return -ENOMEM; ep_ring = virt_dev->new_ep_rings[ep_index]; - ep_ctx->deq[0] = ep_ring->first_seg->dma | ep_ring->cycle_state; - ep_ctx->deq[1] = 0; + ep_ctx->deq = ep_ring->first_seg->dma | ep_ring->cycle_state; ep_ctx->ep_info = xhci_get_endpoint_interval(udev, ep); @@ -535,8 +531,7 @@ void xhci_endpoint_zero(struct xhci_hcd *xhci, ep_ctx->ep_info = 0; ep_ctx->ep_info2 = 0; - ep_ctx->deq[0] = 0; - ep_ctx->deq[1] = 0; + ep_ctx->deq = 0; ep_ctx->tx_info = 0; /* Don't free the endpoint ring until the set interface or configuration * request succeeds. @@ -551,10 +546,8 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) /* Free the Event Ring Segment Table and the actual Event Ring */ xhci_writel(xhci, 0, &xhci->ir_set->erst_size); - xhci_writel(xhci, 0, &xhci->ir_set->erst_base[0]); - xhci_writel(xhci, 0, &xhci->ir_set->erst_base[1]); - xhci_writel(xhci, 0, &xhci->ir_set->erst_dequeue[0]); - xhci_writel(xhci, 0, &xhci->ir_set->erst_dequeue[1]); + xhci_write_64(xhci, 0, &xhci->ir_set->erst_base); + xhci_write_64(xhci, 0, &xhci->ir_set->erst_dequeue); size = sizeof(struct xhci_erst_entry)*(xhci->erst.num_entries); if (xhci->erst.entries) pci_free_consistent(pdev, size, @@ -566,8 +559,7 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) xhci->event_ring = NULL; xhci_dbg(xhci, "Freed event ring\n"); - xhci_writel(xhci, 0, &xhci->op_regs->cmd_ring[0]); - xhci_writel(xhci, 0, &xhci->op_regs->cmd_ring[1]); + xhci_write_64(xhci, 0, &xhci->op_regs->cmd_ring); if (xhci->cmd_ring) xhci_ring_free(xhci, xhci->cmd_ring); xhci->cmd_ring = NULL; @@ -586,8 +578,7 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) xhci->device_pool = NULL; xhci_dbg(xhci, "Freed device context pool\n"); - xhci_writel(xhci, 0, &xhci->op_regs->dcbaa_ptr[0]); - xhci_writel(xhci, 0, &xhci->op_regs->dcbaa_ptr[1]); + xhci_write_64(xhci, 0, &xhci->op_regs->dcbaa_ptr); if (xhci->dcbaa) pci_free_consistent(pdev, sizeof(*xhci->dcbaa), xhci->dcbaa, xhci->dcbaa->dma); @@ -602,6 +593,7 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) dma_addr_t dma; struct device *dev = xhci_to_hcd(xhci)->self.controller; unsigned int val, val2; + u64 val_64; struct xhci_segment *seg; u32 page_size; int i; @@ -647,8 +639,7 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) xhci->dcbaa->dma = dma; xhci_dbg(xhci, "// Device context base array address = 0x%llx (DMA), %p (virt)\n", (unsigned long long)xhci->dcbaa->dma, xhci->dcbaa); - xhci_writel(xhci, dma, &xhci->op_regs->dcbaa_ptr[0]); - xhci_writel(xhci, (u32) 0, &xhci->op_regs->dcbaa_ptr[1]); + xhci_write_64(xhci, dma, &xhci->op_regs->dcbaa_ptr); /* * Initialize the ring segment pool. The ring must be a contiguous @@ -675,14 +666,12 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) (unsigned long long)xhci->cmd_ring->first_seg->dma); /* Set the address in the Command Ring Control register */ - val = xhci_readl(xhci, &xhci->op_regs->cmd_ring[0]); - val = (val & ~CMD_RING_ADDR_MASK) | - (xhci->cmd_ring->first_seg->dma & CMD_RING_ADDR_MASK) | + val_64 = xhci_read_64(xhci, &xhci->op_regs->cmd_ring); + val_64 = (val_64 & (u64) CMD_RING_RSVD_BITS) | + (xhci->cmd_ring->first_seg->dma & (u64) ~CMD_RING_RSVD_BITS) | xhci->cmd_ring->cycle_state; - xhci_dbg(xhci, "// Setting command ring address low bits to 0x%x\n", val); - xhci_writel(xhci, val, &xhci->op_regs->cmd_ring[0]); - xhci_dbg(xhci, "// Setting command ring address high bits to 0x0\n"); - xhci_writel(xhci, (u32) 0, &xhci->op_regs->cmd_ring[1]); + xhci_dbg(xhci, "// Setting command ring address to 0x%x\n", val); + xhci_write_64(xhci, val_64, &xhci->op_regs->cmd_ring); xhci_dbg_cmd_ptrs(xhci); val = xhci_readl(xhci, &xhci->cap_regs->db_off); @@ -722,8 +711,7 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) /* set ring base address and size for each segment table entry */ for (val = 0, seg = xhci->event_ring->first_seg; val < ERST_NUM_SEGS; val++) { struct xhci_erst_entry *entry = &xhci->erst.entries[val]; - entry->seg_addr[0] = seg->dma; - entry->seg_addr[1] = 0; + entry->seg_addr = seg->dma; entry->seg_size = TRBS_PER_SEGMENT; entry->rsvd = 0; seg = seg->next; @@ -741,11 +729,10 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) /* set the segment table base address */ xhci_dbg(xhci, "// Set ERST base address for ir_set 0 = 0x%llx\n", (unsigned long long)xhci->erst.erst_dma_addr); - val = xhci_readl(xhci, &xhci->ir_set->erst_base[0]); - val &= ERST_PTR_MASK; - val |= (xhci->erst.erst_dma_addr & ~ERST_PTR_MASK); - xhci_writel(xhci, val, &xhci->ir_set->erst_base[0]); - xhci_writel(xhci, 0, &xhci->ir_set->erst_base[1]); + val_64 = xhci_read_64(xhci, &xhci->ir_set->erst_base); + val_64 &= ERST_PTR_MASK; + val_64 |= (xhci->erst.erst_dma_addr & (u64) ~ERST_PTR_MASK); + xhci_write_64(xhci, val_64, &xhci->ir_set->erst_base); /* Set the event ring dequeue address */ xhci_set_hc_event_deq(xhci); diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index d672ba14ff8..588686fca47 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -237,7 +237,7 @@ static int room_on_ring(struct xhci_hcd *xhci, struct xhci_ring *ring, void xhci_set_hc_event_deq(struct xhci_hcd *xhci) { - u32 temp; + u64 temp; dma_addr_t deq; deq = xhci_trb_virt_to_dma(xhci->event_ring->deq_seg, @@ -246,13 +246,12 @@ void xhci_set_hc_event_deq(struct xhci_hcd *xhci) xhci_warn(xhci, "WARN something wrong with SW event ring " "dequeue ptr.\n"); /* Update HC event ring dequeue pointer */ - temp = xhci_readl(xhci, &xhci->ir_set->erst_dequeue[0]); + temp = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); temp &= ERST_PTR_MASK; if (!in_interrupt()) xhci_dbg(xhci, "// Write event ring dequeue pointer\n"); - xhci_writel(xhci, 0, &xhci->ir_set->erst_dequeue[1]); - xhci_writel(xhci, (deq & ~ERST_PTR_MASK) | temp, - &xhci->ir_set->erst_dequeue[0]); + xhci_write_64(xhci, ((u64) deq & (u64) ~ERST_PTR_MASK) | temp, + &xhci->ir_set->erst_dequeue); } /* Ring the host controller doorbell after placing a command on the ring */ @@ -352,7 +351,7 @@ static void find_new_dequeue_state(struct xhci_hcd *xhci, if (!state->new_deq_seg) BUG(); /* Dig out the cycle state saved by the xHC during the stop ep cmd */ - state->new_cycle_state = 0x1 & dev->out_ctx->ep[ep_index].deq[0]; + state->new_cycle_state = 0x1 & dev->out_ctx->ep[ep_index].deq; state->new_deq_ptr = cur_td->last_trb; state->new_deq_seg = find_trb_seg(state->new_deq_seg, @@ -594,10 +593,8 @@ static void handle_set_deq_completion(struct xhci_hcd *xhci, * cancelling URBs, which might not be an error... */ } else { - xhci_dbg(xhci, "Successful Set TR Deq Ptr cmd, deq[0] = 0x%x, " - "deq[1] = 0x%x.\n", - dev->out_ctx->ep[ep_index].deq[0], - dev->out_ctx->ep[ep_index].deq[1]); + xhci_dbg(xhci, "Successful Set TR Deq Ptr cmd, deq = @%08llx\n", + dev->out_ctx->ep[ep_index].deq); } ep_ring->state &= ~SET_DEQ_PENDING; @@ -631,7 +628,7 @@ static void handle_cmd_completion(struct xhci_hcd *xhci, u64 cmd_dma; dma_addr_t cmd_dequeue_dma; - cmd_dma = (((u64) event->cmd_trb[1]) << 32) + event->cmd_trb[0]; + cmd_dma = event->cmd_trb; cmd_dequeue_dma = xhci_trb_virt_to_dma(xhci->cmd_ring->deq_seg, xhci->cmd_ring->dequeue); /* Is the command ring deq ptr out of sync with the deq seg ptr? */ @@ -794,10 +791,7 @@ static int handle_tx_event(struct xhci_hcd *xhci, return -ENODEV; } - event_dma = event->buffer[0]; - if (event->buffer[1] != 0) - xhci_warn(xhci, "WARN ignoring upper 32-bits of 64-bit TRB dma address\n"); - + event_dma = event->buffer; /* This TRB should be in the TD at the head of this ring's TD list */ if (list_empty(&ep_ring->td_list)) { xhci_warn(xhci, "WARN Event TRB for slot %d ep %d with no TDs queued?\n", @@ -821,10 +815,10 @@ static int handle_tx_event(struct xhci_hcd *xhci, event_trb = &event_seg->trbs[(event_dma - event_seg->dma) / sizeof(*event_trb)]; xhci_dbg(xhci, "Event TRB with TRB type ID %u\n", (unsigned int) (event->flags & TRB_TYPE_BITMASK)>>10); - xhci_dbg(xhci, "Offset 0x00 (buffer[0]) = 0x%x\n", - (unsigned int) event->buffer[0]); - xhci_dbg(xhci, "Offset 0x04 (buffer[0]) = 0x%x\n", - (unsigned int) event->buffer[1]); + xhci_dbg(xhci, "Offset 0x00 (buffer lo) = 0x%x\n", + lower_32_bits(event->buffer)); + xhci_dbg(xhci, "Offset 0x04 (buffer hi) = 0x%x\n", + upper_32_bits(event->buffer)); xhci_dbg(xhci, "Offset 0x08 (transfer length) = 0x%x\n", (unsigned int) event->transfer_len); xhci_dbg(xhci, "Offset 0x0C (flags) = 0x%x\n", @@ -1343,8 +1337,8 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags, TD_REMAINDER(urb->transfer_buffer_length - running_total) | TRB_INTR_TARGET(0); queue_trb(xhci, ep_ring, false, - (u32) addr, - (u32) ((u64) addr >> 32), + lower_32_bits(addr), + upper_32_bits(addr), length_field, /* We always want to know if the TRB was short, * or we won't get an event when it completes. @@ -1475,8 +1469,8 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, TD_REMAINDER(urb->transfer_buffer_length - running_total) | TRB_INTR_TARGET(0); queue_trb(xhci, ep_ring, false, - (u32) addr, - (u32) ((u64) addr >> 32), + lower_32_bits(addr), + upper_32_bits(addr), length_field, /* We always want to know if the TRB was short, * or we won't get an event when it completes. @@ -1637,7 +1631,8 @@ int xhci_queue_slot_control(struct xhci_hcd *xhci, u32 trb_type, u32 slot_id) int xhci_queue_address_device(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr, u32 slot_id) { - return queue_command(xhci, in_ctx_ptr, 0, 0, + return queue_command(xhci, lower_32_bits(in_ctx_ptr), + upper_32_bits(in_ctx_ptr), 0, TRB_TYPE(TRB_ADDR_DEV) | SLOT_ID_FOR_TRB(slot_id)); } @@ -1645,7 +1640,8 @@ int xhci_queue_address_device(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr, int xhci_queue_configure_endpoint(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr, u32 slot_id) { - return queue_command(xhci, in_ctx_ptr, 0, 0, + return queue_command(xhci, lower_32_bits(in_ctx_ptr), + upper_32_bits(in_ctx_ptr), 0, TRB_TYPE(TRB_CONFIG_EP) | SLOT_ID_FOR_TRB(slot_id)); } @@ -1677,7 +1673,8 @@ static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id, xhci_warn(xhci, "WARN Cannot submit Set TR Deq Ptr\n"); xhci_warn(xhci, "WARN deq seg = %p, deq pt = %p\n", deq_seg, deq_ptr); - return queue_command(xhci, (u32) addr | cycle_state, 0, 0, + return queue_command(xhci, lower_32_bits(addr) | cycle_state, + upper_32_bits(addr), 0, trb_slot_id | trb_ep_index | type); } diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index cde648a524f..60770c89132 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -25,6 +25,7 @@ #include #include +#include #include "../core/hcd.h" /* Code sharing between pci-quirks and xhci hcd */ @@ -42,14 +43,6 @@ * xHCI register interface. * This corresponds to the eXtensible Host Controller Interface (xHCI) * Revision 0.95 specification - * - * Registers should always be accessed with double word or quad word accesses. - * - * Some xHCI implementations may support 64-bit address pointers. Registers - * with 64-bit address pointers should be written to with dword accesses by - * writing the low dword first (ptr[0]), then the high dword (ptr[1]) second. - * xHCI implementations that do not support 64-bit address pointers will ignore - * the high dword, and write order is irrelevant. */ /** @@ -166,10 +159,10 @@ struct xhci_op_regs { u32 reserved1; u32 reserved2; u32 dev_notification; - u32 cmd_ring[2]; + u64 cmd_ring; /* rsvd: offset 0x20-2F */ u32 reserved3[4]; - u32 dcbaa_ptr[2]; + u64 dcbaa_ptr; u32 config_reg; /* rsvd: offset 0x3C-3FF */ u32 reserved4[241]; @@ -254,7 +247,7 @@ struct xhci_op_regs { #define CMD_RING_RUNNING (1 << 3) /* bits 4:5 reserved and should be preserved */ /* Command Ring pointer - bit mask for the lower 32 bits. */ -#define CMD_RING_ADDR_MASK (0xffffffc0) +#define CMD_RING_RSVD_BITS (0x3f) /* CONFIG - Configure Register - config_reg bitmasks */ /* bits 0:7 - maximum number of device slots enabled (NumSlotsEn) */ @@ -382,8 +375,8 @@ struct xhci_intr_reg { u32 irq_control; u32 erst_size; u32 rsvd; - u32 erst_base[2]; - u32 erst_dequeue[2]; + u64 erst_base; + u64 erst_dequeue; }; /* irq_pending bitmasks */ @@ -538,7 +531,7 @@ struct xhci_slot_ctx { struct xhci_ep_ctx { u32 ep_info; u32 ep_info2; - u32 deq[2]; + u64 deq; u32 tx_info; /* offset 0x14 - 0x1f reserved for HC internal use */ u32 reserved[3]; @@ -641,7 +634,7 @@ struct xhci_virt_device { */ struct xhci_device_context_array { /* 64-bit device addresses; we only write 32-bit addresses */ - u32 dev_context_ptrs[2*MAX_HC_SLOTS]; + u64 dev_context_ptrs[MAX_HC_SLOTS]; /* private xHCD pointers */ dma_addr_t dma; }; @@ -654,7 +647,7 @@ struct xhci_device_context_array { struct xhci_stream_ctx { /* 64-bit stream ring address, cycle state, and stream type */ - u32 stream_ring[2]; + u64 stream_ring; /* offset 0x14 - 0x1f reserved for HC internal use */ u32 reserved[2]; }; @@ -662,7 +655,7 @@ struct xhci_stream_ctx { struct xhci_transfer_event { /* 64-bit buffer address, or immediate data */ - u32 buffer[2]; + u64 buffer; u32 transfer_len; /* This field is interpreted differently based on the type of TRB */ u32 flags; @@ -744,7 +737,7 @@ struct xhci_transfer_event { struct xhci_link_trb { /* 64-bit segment pointer*/ - u32 segment_ptr[2]; + u64 segment_ptr; u32 intr_target; u32 control; }; @@ -755,7 +748,7 @@ struct xhci_link_trb { /* Command completion event TRB */ struct xhci_event_cmd { /* Pointer to command TRB, or the value passed by the event data trb */ - u32 cmd_trb[2]; + u64 cmd_trb; u32 status; u32 flags; }; @@ -943,7 +936,7 @@ struct xhci_ring { struct xhci_erst_entry { /* 64-bit event ring segment address */ - u32 seg_addr[2]; + u64 seg_addr; u32 seg_size; /* Set to zero */ u32 rsvd; @@ -1079,6 +1072,38 @@ static inline void xhci_writel(struct xhci_hcd *xhci, writel(val, regs); } +/* + * Registers should always be accessed with double word or quad word accesses. + * + * Some xHCI implementations may support 64-bit address pointers. Registers + * with 64-bit address pointers should be written to with dword accesses by + * writing the low dword first (ptr[0]), then the high dword (ptr[1]) second. + * xHCI implementations that do not support 64-bit address pointers will ignore + * the high dword, and write order is irrelevant. + */ +static inline u64 xhci_read_64(const struct xhci_hcd *xhci, + __u64 __iomem *regs) +{ + __u32 __iomem *ptr = (__u32 __iomem *) regs; + u64 val_lo = readl(ptr); + u64 val_hi = readl(ptr + 1); + return val_lo + (val_hi << 32); +} +static inline void xhci_write_64(struct xhci_hcd *xhci, + const u64 val, __u64 __iomem *regs) +{ + __u32 __iomem *ptr = (__u32 __iomem *) regs; + u32 val_lo = lower_32_bits(val); + u32 val_hi = upper_32_bits(val); + + if (!in_interrupt()) + xhci_dbg(xhci, + "`MEM_WRITE_DWORD(3'b000, 64'h%p, 64'h%0lx, 4'hf);\n", + regs, (long unsigned int) val); + writel(val_lo, ptr); + writel(val_hi, ptr + 1); +} + /* xHCI debugging */ void xhci_print_ir_set(struct xhci_hcd *xhci, struct xhci_intr_reg *ir_set, int set_num); void xhci_print_registers(struct xhci_hcd *xhci); -- GitLab From 62889610f5591005bed9517360e17531684f72d0 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:03:36 -0700 Subject: [PATCH 0438/1342] USB: xhci: Handle short control packets correctly. When there is a short packet on a control transfer, the xHCI host controller hardware will generate two events. The first event will be for the data stage TD with a completion code for a short packet. The second event will be for the status stage with a successful completion code. Before this patch, the xHCI driver would giveback the short control URB when it received the event for the data stage TD. Then it would become confused when it saw a status stage event for the endpoint for an URB it had already finished processing. Change the xHCI host controller driver to wait for the status stage event when it receives a short transfer completion code for a data stage TD. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-ring.c | 14 +++++++++++--- 1 file changed, 11 insertions(+), 3 deletions(-) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 588686fca47..5dd3b1fd71c 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -892,15 +892,23 @@ static int handle_tx_event(struct xhci_hcd *xhci, if (event_trb != ep_ring->dequeue) { /* The event was for the status stage */ if (event_trb == td->last_trb) { - td->urb->actual_length = - td->urb->transfer_buffer_length; + /* Did we already see a short data stage? */ + if (td->urb->actual_length != 0) + status = -EREMOTEIO; + else + td->urb->actual_length = + td->urb->transfer_buffer_length; } else { /* Maybe the event was for the data stage? */ - if (GET_COMP_CODE(event->transfer_len) != COMP_STOP_INVAL) + if (GET_COMP_CODE(event->transfer_len) != COMP_STOP_INVAL) { /* We didn't stop on a link TRB in the middle */ td->urb->actual_length = td->urb->transfer_buffer_length - TRB_LEN(event->transfer_len); + xhci_dbg(xhci, "Waiting for status stage event\n"); + urb = NULL; + goto cleanup; + } } } } else { -- GitLab From 2d83109be62edd9647c45d7ed2b916b03974a7ec Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:03:40 -0700 Subject: [PATCH 0439/1342] USB: xhci: Correct Event Handler Busy flag usage. The Event Handler Busy bit in the event ring dequeue pointer is write 1 to clear. Fix the interrupt service routine to clear that bit after the event handler has run. xhci_set_hc_event_deq() is designed to update the event ring dequeue pointer without changing any of the four reserved bits in the lower nibble. The event handler busy (EHB) bit is write one to clear, so the new value must always contain a zero in that bit in order to preserve the EHB value. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-hcd.c | 4 ++-- drivers/usb/host/xhci-ring.c | 6 +++++- 2 files changed, 7 insertions(+), 3 deletions(-) diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index e15773598e4..2e8e5bf6b6c 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -249,9 +249,9 @@ static void xhci_work(struct xhci_hcd *xhci) /* FIXME this should be a delayed service routine that clears the EHB */ xhci_handle_event(xhci); - /* Clear the event handler busy flag; the event ring should be empty. */ + /* Clear the event handler busy flag (RW1C); the event ring should be empty. */ temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); - xhci_write_64(xhci, temp_64 & ~ERST_EHB, &xhci->ir_set->erst_dequeue); + xhci_write_64(xhci, temp_64 | ERST_EHB, &xhci->ir_set->erst_dequeue); /* Flush posted writes -- FIXME is this necessary? */ xhci_readl(xhci, &xhci->ir_set->irq_pending); } diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 5dd3b1fd71c..fe9541a89a3 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -248,8 +248,12 @@ void xhci_set_hc_event_deq(struct xhci_hcd *xhci) /* Update HC event ring dequeue pointer */ temp = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); temp &= ERST_PTR_MASK; + /* Don't clear the EHB bit (which is RW1C) because + * there might be more events to service. + */ + temp &= ~ERST_EHB; if (!in_interrupt()) - xhci_dbg(xhci, "// Write event ring dequeue pointer\n"); + xhci_dbg(xhci, "// Write event ring dequeue pointer, preserving EHB bit\n"); xhci_write_64(xhci, ((u64) deq & (u64) ~ERST_PTR_MASK) | temp, &xhci->ir_set->erst_dequeue); } -- GitLab From 66e49d8774fa03539713e8f91169c37c05df1e94 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:03:46 -0700 Subject: [PATCH 0440/1342] USB: xhci: Make debugging more verbose. Add more debugging to the irq handler, slot context initialization, ring operations, URB cancellation, and MMIO writes. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-hcd.c | 47 +++++++++++++++++++++++++----------- drivers/usb/host/xhci-ring.c | 35 +++++++++++++++++++++++++-- drivers/usb/host/xhci.h | 14 +++++------ 3 files changed, 72 insertions(+), 24 deletions(-) diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index 2e8e5bf6b6c..764995fd59e 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -267,8 +267,10 @@ irqreturn_t xhci_irq(struct usb_hcd *hcd) { struct xhci_hcd *xhci = hcd_to_xhci(hcd); u32 temp, temp2; + union xhci_trb *trb; spin_lock(&xhci->lock); + trb = xhci->event_ring->dequeue; /* Check if the xHC generated the interrupt, or the irq is shared */ temp = xhci_readl(xhci, &xhci->op_regs->status); temp2 = xhci_readl(xhci, &xhci->ir_set->irq_pending); @@ -276,6 +278,15 @@ irqreturn_t xhci_irq(struct usb_hcd *hcd) spin_unlock(&xhci->lock); return IRQ_NONE; } + xhci_dbg(xhci, "op reg status = %08x\n", temp); + xhci_dbg(xhci, "ir set irq_pending = %08x\n", temp2); + xhci_dbg(xhci, "Event ring dequeue ptr:\n"); + xhci_dbg(xhci, "@%llx %08x %08x %08x %08x\n", + (unsigned long long)xhci_trb_virt_to_dma(xhci->event_ring->deq_seg, trb), + lower_32_bits(trb->link.segment_ptr), + upper_32_bits(trb->link.segment_ptr), + (unsigned int) trb->link.intr_target, + (unsigned int) trb->link.control); if (temp & STS_FATAL) { xhci_warn(xhci, "WARNING: Host System Error\n"); @@ -385,6 +396,20 @@ int xhci_run(struct usb_hcd *hcd) add_timer(&xhci->event_ring_timer); #endif + xhci_dbg(xhci, "Command ring memory map follows:\n"); + xhci_debug_ring(xhci, xhci->cmd_ring); + xhci_dbg_ring_ptrs(xhci, xhci->cmd_ring); + xhci_dbg_cmd_ptrs(xhci); + + xhci_dbg(xhci, "ERST memory map follows:\n"); + xhci_dbg_erst(xhci, &xhci->erst); + xhci_dbg(xhci, "Event ring:\n"); + xhci_debug_ring(xhci, xhci->event_ring); + xhci_dbg_ring_ptrs(xhci, xhci->event_ring); + temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); + temp_64 &= ~ERST_PTR_MASK; + xhci_dbg(xhci, "ERST deq = 64'h%0lx\n", (long unsigned int) temp_64); + xhci_dbg(xhci, "// Set the interrupt modulation register\n"); temp = xhci_readl(xhci, &xhci->ir_set->irq_control); temp &= ~ER_IRQ_INTERVAL_MASK; @@ -409,20 +434,6 @@ int xhci_run(struct usb_hcd *hcd) if (NUM_TEST_NOOPS > 0) doorbell = xhci_setup_one_noop(xhci); - xhci_dbg(xhci, "Command ring memory map follows:\n"); - xhci_debug_ring(xhci, xhci->cmd_ring); - xhci_dbg_ring_ptrs(xhci, xhci->cmd_ring); - xhci_dbg_cmd_ptrs(xhci); - - xhci_dbg(xhci, "ERST memory map follows:\n"); - xhci_dbg_erst(xhci, &xhci->erst); - xhci_dbg(xhci, "Event ring:\n"); - xhci_debug_ring(xhci, xhci->event_ring); - xhci_dbg_ring_ptrs(xhci, xhci->event_ring); - temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); - temp_64 &= ~ERST_PTR_MASK; - xhci_dbg(xhci, "ERST deq = 64'h%0lx\n", (long unsigned int) temp_64); - temp = xhci_readl(xhci, &xhci->op_regs->command); temp |= (CMD_RUN); xhci_dbg(xhci, "// Turn on HC, cmd = 0x%x.\n", @@ -665,8 +676,12 @@ int xhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status) goto done; xhci_dbg(xhci, "Cancel URB %p\n", urb); + xhci_dbg(xhci, "Event ring:\n"); + xhci_debug_ring(xhci, xhci->event_ring); ep_index = xhci_get_endpoint_index(&urb->ep->desc); ep_ring = xhci->devs[urb->dev->slot_id]->ep_rings[ep_index]; + xhci_dbg(xhci, "Endpoint ring:\n"); + xhci_debug_ring(xhci, ep_ring); td = (struct xhci_td *) urb->hcpriv; ep_ring->cancels_pending++; @@ -1178,6 +1193,8 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) if (!udev->config) xhci_setup_addressable_virt_dev(xhci, udev); /* Otherwise, assume the core has the device configured how it wants */ + xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id); + xhci_dbg_ctx(xhci, virt_dev->in_ctx, virt_dev->in_ctx_dma, 2); spin_lock_irqsave(&xhci->lock, flags); ret = xhci_queue_address_device(xhci, virt_dev->in_ctx_dma, @@ -1221,6 +1238,8 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) default: xhci_err(xhci, "ERROR: unexpected command completion " "code 0x%x.\n", virt_dev->cmd_status); + xhci_dbg(xhci, "Slot ID %d Output Context:\n", udev->slot_id); + xhci_dbg_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, 2); ret = -EINVAL; break; } diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index fe9541a89a3..1fc0decfa0a 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -135,6 +135,7 @@ static void next_trb(struct xhci_hcd *xhci, static void inc_deq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer) { union xhci_trb *next = ++(ring->dequeue); + unsigned long long addr; ring->deq_updates++; /* Update the dequeue pointer further if that was a link TRB or we're at @@ -152,6 +153,13 @@ static void inc_deq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer ring->dequeue = ring->deq_seg->trbs; next = ring->dequeue; } + addr = (unsigned long long) xhci_trb_virt_to_dma(ring->deq_seg, ring->dequeue); + if (ring == xhci->event_ring) + xhci_dbg(xhci, "Event ring deq = 0x%llx (DMA)\n", addr); + else if (ring == xhci->cmd_ring) + xhci_dbg(xhci, "Command ring deq = 0x%llx (DMA)\n", addr); + else + xhci_dbg(xhci, "Ring deq = 0x%llx (DMA)\n", addr); } /* @@ -171,6 +179,7 @@ static void inc_enq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer { u32 chain; union xhci_trb *next; + unsigned long long addr; chain = ring->enqueue->generic.field[3] & TRB_CHAIN; next = ++(ring->enqueue); @@ -204,6 +213,13 @@ static void inc_enq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer ring->enqueue = ring->enq_seg->trbs; next = ring->enqueue; } + addr = (unsigned long long) xhci_trb_virt_to_dma(ring->enq_seg, ring->enqueue); + if (ring == xhci->event_ring) + xhci_dbg(xhci, "Event ring enq = 0x%llx (DMA)\n", addr); + else if (ring == xhci->cmd_ring) + xhci_dbg(xhci, "Command ring enq = 0x%llx (DMA)\n", addr); + else + xhci_dbg(xhci, "Ring enq = 0x%llx (DMA)\n", addr); } /* @@ -252,8 +268,7 @@ void xhci_set_hc_event_deq(struct xhci_hcd *xhci) * there might be more events to service. */ temp &= ~ERST_EHB; - if (!in_interrupt()) - xhci_dbg(xhci, "// Write event ring dequeue pointer, preserving EHB bit\n"); + xhci_dbg(xhci, "// Write event ring dequeue pointer, preserving EHB bit\n"); xhci_write_64(xhci, ((u64) deq & (u64) ~ERST_PTR_MASK) | temp, &xhci->ir_set->erst_dequeue); } @@ -781,6 +796,7 @@ static int handle_tx_event(struct xhci_hcd *xhci, struct urb *urb = 0; int status = -EINPROGRESS; + xhci_dbg(xhci, "In %s\n", __func__); xdev = xhci->devs[TRB_TO_SLOT_ID(event->flags)]; if (!xdev) { xhci_err(xhci, "ERROR Transfer event pointed to bad slot\n"); @@ -789,6 +805,7 @@ static int handle_tx_event(struct xhci_hcd *xhci, /* Endpoint ID is 1 based, our index is zero based */ ep_index = TRB_TO_EP_ID(event->flags) - 1; + xhci_dbg(xhci, "%s - ep index = %d\n", __func__, ep_index); ep_ring = xdev->ep_rings[ep_index]; if (!ep_ring || (xdev->out_ctx->ep[ep_index].ep_info & EP_STATE_MASK) == EP_STATE_DISABLED) { xhci_err(xhci, "ERROR Transfer event pointed to disabled endpoint\n"); @@ -797,6 +814,7 @@ static int handle_tx_event(struct xhci_hcd *xhci, event_dma = event->buffer; /* This TRB should be in the TD at the head of this ring's TD list */ + xhci_dbg(xhci, "%s - checking for list empty\n", __func__); if (list_empty(&ep_ring->td_list)) { xhci_warn(xhci, "WARN Event TRB for slot %d ep %d with no TDs queued?\n", TRB_TO_SLOT_ID(event->flags), ep_index); @@ -806,11 +824,14 @@ static int handle_tx_event(struct xhci_hcd *xhci, urb = NULL; goto cleanup; } + xhci_dbg(xhci, "%s - getting list entry\n", __func__); td = list_entry(ep_ring->td_list.next, struct xhci_td, td_list); /* Is this a TRB in the currently executing TD? */ + xhci_dbg(xhci, "%s - looking for TD\n", __func__); event_seg = trb_in_td(ep_ring->deq_seg, ep_ring->dequeue, td->last_trb, event_dma); + xhci_dbg(xhci, "%s - found event_seg = %p\n", __func__, event_seg); if (!event_seg) { /* HC is busted, give up! */ xhci_err(xhci, "ERROR Transfer event TRB DMA ptr not part of current TD\n"); @@ -1027,6 +1048,8 @@ cleanup: /* FIXME for multi-TD URBs (who have buffers bigger than 64MB) */ if (urb) { usb_hcd_unlink_urb_from_ep(xhci_to_hcd(xhci), urb); + xhci_dbg(xhci, "Giveback URB %p, len = %d, status = %d\n", + urb, td->urb->actual_length, status); spin_unlock(&xhci->lock); usb_hcd_giveback_urb(xhci_to_hcd(xhci), urb, status); spin_lock(&xhci->lock); @@ -1044,6 +1067,7 @@ void xhci_handle_event(struct xhci_hcd *xhci) int update_ptrs = 1; int ret; + xhci_dbg(xhci, "In %s\n", __func__); if (!xhci->event_ring || !xhci->event_ring->dequeue) { xhci->error_bitmask |= 1 << 1; return; @@ -1056,18 +1080,25 @@ void xhci_handle_event(struct xhci_hcd *xhci) xhci->error_bitmask |= 1 << 2; return; } + xhci_dbg(xhci, "%s - OS owns TRB\n", __func__); /* FIXME: Handle more event types. */ switch ((event->event_cmd.flags & TRB_TYPE_BITMASK)) { case TRB_TYPE(TRB_COMPLETION): + xhci_dbg(xhci, "%s - calling handle_cmd_completion\n", __func__); handle_cmd_completion(xhci, &event->event_cmd); + xhci_dbg(xhci, "%s - returned from handle_cmd_completion\n", __func__); break; case TRB_TYPE(TRB_PORT_STATUS): + xhci_dbg(xhci, "%s - calling handle_port_status\n", __func__); handle_port_status(xhci, event); + xhci_dbg(xhci, "%s - returned from handle_port_status\n", __func__); update_ptrs = 0; break; case TRB_TYPE(TRB_TRANSFER): + xhci_dbg(xhci, "%s - calling handle_tx_event\n", __func__); ret = handle_tx_event(xhci, &event->trans_event); + xhci_dbg(xhci, "%s - returned from handle_tx_event\n", __func__); if (ret < 0) xhci->error_bitmask |= 1 << 9; else diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 60770c89132..074728e1022 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -1065,10 +1065,9 @@ static inline unsigned int xhci_readl(const struct xhci_hcd *xhci, static inline void xhci_writel(struct xhci_hcd *xhci, const unsigned int val, __u32 __iomem *regs) { - if (!in_interrupt()) - xhci_dbg(xhci, - "`MEM_WRITE_DWORD(3'b000, 32'h%p, 32'h%0x, 4'hf);\n", - regs, val); + xhci_dbg(xhci, + "`MEM_WRITE_DWORD(3'b000, 32'h%p, 32'h%0x, 4'hf);\n", + regs, val); writel(val, regs); } @@ -1096,10 +1095,9 @@ static inline void xhci_write_64(struct xhci_hcd *xhci, u32 val_lo = lower_32_bits(val); u32 val_hi = upper_32_bits(val); - if (!in_interrupt()) - xhci_dbg(xhci, - "`MEM_WRITE_DWORD(3'b000, 64'h%p, 64'h%0lx, 4'hf);\n", - regs, (long unsigned int) val); + xhci_dbg(xhci, + "`MEM_WRITE_DWORD(3'b000, 64'h%p, 64'h%0lx, 4'hf);\n", + regs, (long unsigned int) val); writel(val_lo, ptr); writel(val_hi, ptr + 1); } -- GitLab From d3512f63494678dc58e44a20c56278718fd58969 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:03:50 -0700 Subject: [PATCH 0441/1342] USB: xhci: Don't oops if the host doesn't halt. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-hcd.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index 764995fd59e..8c3a074a95c 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -103,7 +103,10 @@ int xhci_reset(struct xhci_hcd *xhci) u32 state; state = xhci_readl(xhci, &xhci->op_regs->status); - BUG_ON((state & STS_HALT) == 0); + if ((state & STS_HALT) == 0) { + xhci_warn(xhci, "Host controller not halted, aborting reset.\n"); + return 0; + } xhci_dbg(xhci, "// Reset the HC\n"); command = xhci_readl(xhci, &xhci->op_regs->command); -- GitLab From fcf8f576beafb8c5db8aee8a73eb73763fa7b0ad Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:04:01 -0700 Subject: [PATCH 0442/1342] USB: xhci: Check if the host controller died in IRQ handler. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-hcd.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index 8c3a074a95c..008326d5bc5 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -277,6 +277,9 @@ irqreturn_t xhci_irq(struct usb_hcd *hcd) /* Check if the xHC generated the interrupt, or the irq is shared */ temp = xhci_readl(xhci, &xhci->op_regs->status); temp2 = xhci_readl(xhci, &xhci->ir_set->irq_pending); + if (temp == 0xffffffff && temp2 == 0xffffffff) + goto hw_died; + if (!(temp & STS_EINT) && !ER_IRQ_PENDING(temp2)) { spin_unlock(&xhci->lock); return IRQ_NONE; @@ -294,6 +297,7 @@ irqreturn_t xhci_irq(struct usb_hcd *hcd) if (temp & STS_FATAL) { xhci_warn(xhci, "WARNING: Host System Error\n"); xhci_halt(xhci); +hw_died: xhci_to_hcd(xhci)->state = HC_STATE_HALT; spin_unlock(&xhci->lock); return -ESHUTDOWN; -- GitLab From 47692d179f7a88794bcd302e53ca7899d7592db9 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:04:27 -0700 Subject: [PATCH 0443/1342] USB: xhci: Setup HW retries correctly. The xHCI host controller can be programmed to retry a transfer a certain number of times per endpoint before it passes back an error condition to the host controller driver. The xHC will return an error code when the error count transitions from 1 to 0. Programming an error count of 3 means the xHC tries the transfer 3 times, programming it with a 1 means it tries to transfer once, and programming it with 0 means the HW tries the transfer infinitely. We want isochronous transfers to only be tried once, so set the error count to one. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-mem.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index ec825f16dce..075e1036bcb 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -480,11 +480,13 @@ int xhci_endpoint_init(struct xhci_hcd *xhci, /* FIXME dig Mult and streams info out of ep companion desc */ - /* Allow 3 retries for everything but isoc */ + /* Allow 3 retries for everything but isoc; + * error count = 0 means infinite retries. + */ if (!usb_endpoint_xfer_isoc(&ep->desc)) ep_ctx->ep_info2 = ERROR_COUNT(3); else - ep_ctx->ep_info2 = ERROR_COUNT(0); + ep_ctx->ep_info2 = ERROR_COUNT(1); ep_ctx->ep_info2 |= xhci_get_endpoint_type(udev, ep); -- GitLab From 4a73143ced467868e92d7914d9f8bf797640927b Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:04:32 -0700 Subject: [PATCH 0444/1342] USB: xhci: Handle babble errors on transfers. Pass back a babble error when this error code is seen in the transfer event TRB. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-ring.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 1fc0decfa0a..0903e98989e 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -876,6 +876,10 @@ static int handle_tx_event(struct xhci_hcd *xhci, xhci_warn(xhci, "WARN: transfer error on endpoint\n"); status = -EPROTO; break; + case COMP_BABBLE: + xhci_warn(xhci, "WARN: babble error on endpoint\n"); + status = -EOVERFLOW; + break; case COMP_DB_ERR: xhci_warn(xhci, "WARN: HC couldn't access mem fast enough\n"); status = -ENOSR; -- GitLab From b7d6d99896a6cf38dc354d673afd3fbde10b86c2 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:04:38 -0700 Subject: [PATCH 0445/1342] USB: xhci: Fail gracefully if there's no SS ep companion descriptor. This is a work around for a bug in the SuperSpeed Endpoint Companion Descriptor parsing code. It fails in some corner cases, which means ep->ss_ep_comp may be NULL. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-mem.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index 075e1036bcb..41aca003ee8 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -496,7 +496,12 @@ int xhci_endpoint_init(struct xhci_hcd *xhci, max_packet = ep->desc.wMaxPacketSize; ep_ctx->ep_info2 |= MAX_PACKET(max_packet); /* dig out max burst from ep companion desc */ - max_packet = ep->ss_ep_comp->desc.bMaxBurst; + if (!ep->ss_ep_comp) { + xhci_warn(xhci, "WARN no SS endpoint companion descriptor.\n"); + max_packet = 0; + } else { + max_packet = ep->ss_ep_comp->desc.bMaxBurst; + } ep_ctx->ep_info2 |= MAX_BURST(max_packet); break; case USB_SPEED_HIGH: -- GitLab From 9f8e443816976edd68f415ea25c0223ea921e88c Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:04:52 -0700 Subject: [PATCH 0446/1342] USB: Fix parsing of SuperSpeed Endpoint Companion descriptor. usb_parse_ss_endpoint_companion() was supposed to allocate a structure to hold the SuperSpeed Endpoint Companion descriptor, and either copy the values the device returned, or fill in default values if the device descriptor did not include the companion descriptor. However, the previous code would miss the last endpoint in a configuration with no descriptors after it. Make usb_parse_endpoint() allocate the SS endpoint companion descriptor and fill it with default values, even if we've run out of buffer space in this configuration descriptor. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/config.c | 48 ++++++++++++++++++++++----------------- 1 file changed, 27 insertions(+), 21 deletions(-) diff --git a/drivers/usb/core/config.c b/drivers/usb/core/config.c index 24dfb33f90c..a16c538d013 100644 --- a/drivers/usb/core/config.c +++ b/drivers/usb/core/config.c @@ -80,38 +80,18 @@ static int usb_parse_ss_endpoint_companion(struct device *ddev, int cfgno, int max_tx; int i; - /* Allocate space for the SS endpoint companion descriptor */ - ep->ss_ep_comp = kzalloc(sizeof(struct usb_host_ss_ep_comp), - GFP_KERNEL); - if (!ep->ss_ep_comp) - return -ENOMEM; desc = (struct usb_ss_ep_comp_descriptor *) buffer; if (desc->bDescriptorType != USB_DT_SS_ENDPOINT_COMP) { dev_warn(ddev, "No SuperSpeed endpoint companion for config %d " " interface %d altsetting %d ep %d: " "using minimum values\n", cfgno, inum, asnum, ep->desc.bEndpointAddress); - ep->ss_ep_comp->desc.bLength = USB_DT_SS_EP_COMP_SIZE; - ep->ss_ep_comp->desc.bDescriptorType = USB_DT_SS_ENDPOINT_COMP; - ep->ss_ep_comp->desc.bMaxBurst = 0; - /* - * Leave bmAttributes as zero, which will mean no streams for - * bulk, and isoc won't support multiple bursts of packets. - * With bursts of only one packet, and a Mult of 1, the max - * amount of data moved per endpoint service interval is one - * packet. - */ - if (usb_endpoint_xfer_isoc(&ep->desc) || - usb_endpoint_xfer_int(&ep->desc)) - ep->ss_ep_comp->desc.wBytesPerInterval = - ep->desc.wMaxPacketSize; /* * The next descriptor is for an Endpoint or Interface, * no extra descriptors to copy into the companion structure, * and we didn't eat up any of the buffer. */ - retval = 0; - goto valid; + return 0; } memcpy(&ep->ss_ep_comp->desc, desc, USB_DT_SS_EP_COMP_SIZE); desc = &ep->ss_ep_comp->desc; @@ -320,6 +300,28 @@ static int usb_parse_endpoint(struct device *ddev, int cfgno, int inum, buffer += i; size -= i; + /* Allocate space for the SS endpoint companion descriptor */ + endpoint->ss_ep_comp = kzalloc(sizeof(struct usb_host_ss_ep_comp), + GFP_KERNEL); + if (!endpoint->ss_ep_comp) + return -ENOMEM; + + /* Fill in some default values (may be overwritten later) */ + endpoint->ss_ep_comp->desc.bLength = USB_DT_SS_EP_COMP_SIZE; + endpoint->ss_ep_comp->desc.bDescriptorType = USB_DT_SS_ENDPOINT_COMP; + endpoint->ss_ep_comp->desc.bMaxBurst = 0; + /* + * Leave bmAttributes as zero, which will mean no streams for + * bulk, and isoc won't support multiple bursts of packets. + * With bursts of only one packet, and a Mult of 1, the max + * amount of data moved per endpoint service interval is one + * packet. + */ + if (usb_endpoint_xfer_isoc(&endpoint->desc) || + usb_endpoint_xfer_int(&endpoint->desc)) + endpoint->ss_ep_comp->desc.wBytesPerInterval = + endpoint->desc.wMaxPacketSize; + if (size > 0) { retval = usb_parse_ss_endpoint_companion(ddev, cfgno, inum, asnum, endpoint, num_ep, buffer, @@ -329,6 +331,10 @@ static int usb_parse_endpoint(struct device *ddev, int cfgno, int inum, retval = buffer - buffer0; } } else { + dev_warn(ddev, "config %d interface %d altsetting %d " + "endpoint 0x%X has no " + "SuperSpeed companion descriptor\n", + cfgno, inum, asnum, d->bEndpointAddress); retval = buffer - buffer0; } } else { -- GitLab From 254c80a3a0eb811489f7410c3291f01a60e8e42f Mon Sep 17 00:00:00 2001 From: John Youn Date: Mon, 27 Jul 2009 12:05:03 -0700 Subject: [PATCH 0447/1342] USB: xhci: Scratchpad buffer allocation Allocates and initializes the scratchpad buffer array (XHCI 4.20). This is an array of 64-bit DMA addresses to scratch pages that the controller may use during operation. The number of pages is specified in the "Max Scratchpad Buffers" field of HCSPARAMS2. The DMA address of this array is written into slot 0 of the DCBAA. Signed-off-by: John Youn Acked-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-mem.c | 102 ++++++++++++++++++++++++++++++++++++ drivers/usb/host/xhci.h | 11 ++++ 2 files changed, 113 insertions(+) diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index 41aca003ee8..71121d99235 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -545,6 +545,103 @@ void xhci_endpoint_zero(struct xhci_hcd *xhci, */ } +/* Set up the scratchpad buffer array and scratchpad buffers, if needed. */ +static int scratchpad_alloc(struct xhci_hcd *xhci, gfp_t flags) +{ + int i; + struct device *dev = xhci_to_hcd(xhci)->self.controller; + int num_sp = HCS_MAX_SCRATCHPAD(xhci->hcs_params2); + + xhci_dbg(xhci, "Allocating %d scratchpad buffers\n", num_sp); + + if (!num_sp) + return 0; + + xhci->scratchpad = kzalloc(sizeof(*xhci->scratchpad), flags); + if (!xhci->scratchpad) + goto fail_sp; + + xhci->scratchpad->sp_array = + pci_alloc_consistent(to_pci_dev(dev), + num_sp * sizeof(u64), + &xhci->scratchpad->sp_dma); + if (!xhci->scratchpad->sp_array) + goto fail_sp2; + + xhci->scratchpad->sp_buffers = kzalloc(sizeof(void *) * num_sp, flags); + if (!xhci->scratchpad->sp_buffers) + goto fail_sp3; + + xhci->scratchpad->sp_dma_buffers = + kzalloc(sizeof(dma_addr_t) * num_sp, flags); + + if (!xhci->scratchpad->sp_dma_buffers) + goto fail_sp4; + + xhci->dcbaa->dev_context_ptrs[0] = xhci->scratchpad->sp_dma; + for (i = 0; i < num_sp; i++) { + dma_addr_t dma; + void *buf = pci_alloc_consistent(to_pci_dev(dev), + xhci->page_size, &dma); + if (!buf) + goto fail_sp5; + + xhci->scratchpad->sp_array[i] = dma; + xhci->scratchpad->sp_buffers[i] = buf; + xhci->scratchpad->sp_dma_buffers[i] = dma; + } + + return 0; + + fail_sp5: + for (i = i - 1; i >= 0; i--) { + pci_free_consistent(to_pci_dev(dev), xhci->page_size, + xhci->scratchpad->sp_buffers[i], + xhci->scratchpad->sp_dma_buffers[i]); + } + kfree(xhci->scratchpad->sp_dma_buffers); + + fail_sp4: + kfree(xhci->scratchpad->sp_buffers); + + fail_sp3: + pci_free_consistent(to_pci_dev(dev), num_sp * sizeof(u64), + xhci->scratchpad->sp_array, + xhci->scratchpad->sp_dma); + + fail_sp2: + kfree(xhci->scratchpad); + xhci->scratchpad = NULL; + + fail_sp: + return -ENOMEM; +} + +static void scratchpad_free(struct xhci_hcd *xhci) +{ + int num_sp; + int i; + struct pci_dev *pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller); + + if (!xhci->scratchpad) + return; + + num_sp = HCS_MAX_SCRATCHPAD(xhci->hcs_params2); + + for (i = 0; i < num_sp; i++) { + pci_free_consistent(pdev, xhci->page_size, + xhci->scratchpad->sp_buffers[i], + xhci->scratchpad->sp_dma_buffers[i]); + } + kfree(xhci->scratchpad->sp_dma_buffers); + kfree(xhci->scratchpad->sp_buffers); + pci_free_consistent(pdev, num_sp * sizeof(u64), + xhci->scratchpad->sp_array, + xhci->scratchpad->sp_dma); + kfree(xhci->scratchpad); + xhci->scratchpad = NULL; +} + void xhci_mem_cleanup(struct xhci_hcd *xhci) { struct pci_dev *pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller); @@ -593,6 +690,7 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) xhci->page_size = 0; xhci->page_shift = 0; + scratchpad_free(xhci); } int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) @@ -755,7 +853,11 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) for (i = 0; i < MAX_HC_SLOTS; ++i) xhci->devs[i] = 0; + if (scratchpad_alloc(xhci, flags)) + goto fail; + return 0; + fail: xhci_warn(xhci, "Couldn't initialize memory\n"); xhci_mem_cleanup(xhci); diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 074728e1022..5a09b9a26e0 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -89,6 +89,7 @@ struct xhci_cap_regs { #define HCS_ERST_MAX(p) (((p) >> 4) & 0xf) /* bit 26 Scratchpad restore - for save/restore HW state - not used yet */ /* bits 27:31 number of Scratchpad buffers SW must allocate for the HW */ +#define HCS_MAX_SCRATCHPAD(p) (((p) >> 27) & 0x1f) /* HCSPARAMS3 - hcs_params3 - bitmasks */ /* bits 0:7, Max U1 to U0 latency for the roothub ports */ @@ -951,6 +952,13 @@ struct xhci_erst { unsigned int erst_size; }; +struct xhci_scratchpad { + u64 *sp_array; + dma_addr_t sp_dma; + void **sp_buffers; + dma_addr_t *sp_dma_buffers; +}; + /* * Each segment table entry is 4*32bits long. 1K seems like an ok size: * (1K bytes * 8bytes/bit) / (4*32 bits) = 64 segment entries in the table, @@ -1005,6 +1013,9 @@ struct xhci_hcd { struct xhci_ring *cmd_ring; struct xhci_ring *event_ring; struct xhci_erst erst; + /* Scratchpad */ + struct xhci_scratchpad *scratchpad; + /* slot enabling and address device helpers */ struct completion addr_dev; int slot_id; -- GitLab From 28c2d2efb48dec2f0b050affae6d5787d6449e47 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:05:08 -0700 Subject: [PATCH 0448/1342] USB: xhci: Always align output device contexts to 64 bytes. Make sure the xHCI output device context is 64-byte aligned. Previous code was using the same structure for both the output device context and the input control context. Since the structure had 32 bytes of flags before the device context, the output device context wouldn't be 64-byte aligned. Define a new structure to use for the output device context and clean up the debugging for these two structures. The copy of the device context in the input control context does *not* need to be 64-byte aligned. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-dbg.c | 101 ++++++++++++++++++++++-------------- drivers/usb/host/xhci-hcd.c | 7 +-- drivers/usb/host/xhci-mem.c | 15 +++--- drivers/usb/host/xhci.h | 19 ++++++- 4 files changed, 89 insertions(+), 53 deletions(-) diff --git a/drivers/usb/host/xhci-dbg.c b/drivers/usb/host/xhci-dbg.c index 6d62e4abe3c..d77f8de1125 100644 --- a/drivers/usb/host/xhci-dbg.c +++ b/drivers/usb/host/xhci-dbg.c @@ -393,78 +393,103 @@ void xhci_dbg_cmd_ptrs(struct xhci_hcd *xhci) upper_32_bits(val)); } -void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep) +dma_addr_t xhci_dbg_slot_ctx(struct xhci_hcd *xhci, struct xhci_slot_ctx *slot, dma_addr_t dma) { - int i, j; - int last_ep_ctx = 31; /* Fields are 32 bits wide, DMA addresses are in bytes */ int field_size = 32 / 8; - - xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - drop flags\n", - &ctx->drop_flags, (unsigned long long)dma, - ctx->drop_flags); - dma += field_size; - xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - add flags\n", - &ctx->add_flags, (unsigned long long)dma, - ctx->add_flags); - dma += field_size; - for (i = 0; i < 6; ++i) { - xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n", - &ctx->rsvd[i], (unsigned long long)dma, - ctx->rsvd[i], i); - dma += field_size; - } + int i; xhci_dbg(xhci, "Slot Context:\n"); xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_info\n", - &ctx->slot.dev_info, - (unsigned long long)dma, ctx->slot.dev_info); + &slot->dev_info, + (unsigned long long)dma, slot->dev_info); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_info2\n", - &ctx->slot.dev_info2, - (unsigned long long)dma, ctx->slot.dev_info2); + &slot->dev_info2, + (unsigned long long)dma, slot->dev_info2); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - tt_info\n", - &ctx->slot.tt_info, - (unsigned long long)dma, ctx->slot.tt_info); + &slot->tt_info, + (unsigned long long)dma, slot->tt_info); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_state\n", - &ctx->slot.dev_state, - (unsigned long long)dma, ctx->slot.dev_state); + &slot->dev_state, + (unsigned long long)dma, slot->dev_state); dma += field_size; for (i = 0; i < 4; ++i) { xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n", - &ctx->slot.reserved[i], (unsigned long long)dma, - ctx->slot.reserved[i], i); + &slot->reserved[i], (unsigned long long)dma, + slot->reserved[i], i); dma += field_size; } + return dma; +} + +dma_addr_t xhci_dbg_ep_ctx(struct xhci_hcd *xhci, struct xhci_ep_ctx *ep, dma_addr_t dma, unsigned int last_ep) +{ + int i, j; + int last_ep_ctx = 31; + /* Fields are 32 bits wide, DMA addresses are in bytes */ + int field_size = 32 / 8; + if (last_ep < 31) last_ep_ctx = last_ep + 1; for (i = 0; i < last_ep_ctx; ++i) { xhci_dbg(xhci, "Endpoint %02d Context:\n", i); xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - ep_info\n", - &ctx->ep[i].ep_info, - (unsigned long long)dma, ctx->ep[i].ep_info); + &ep[i].ep_info, + (unsigned long long)dma, ep[i].ep_info); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - ep_info2\n", - &ctx->ep[i].ep_info2, - (unsigned long long)dma, ctx->ep[i].ep_info2); + &ep[i].ep_info2, + (unsigned long long)dma, ep[i].ep_info2); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08llx - deq\n", - &ctx->ep[i].deq, - (unsigned long long)dma, ctx->ep[i].deq); + &ep[i].deq, + (unsigned long long)dma, ep[i].deq); dma += 2*field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - tx_info\n", - &ctx->ep[i].tx_info, - (unsigned long long)dma, ctx->ep[i].tx_info); + &ep[i].tx_info, + (unsigned long long)dma, ep[i].tx_info); dma += field_size; for (j = 0; j < 3; ++j) { xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n", - &ctx->ep[i].reserved[j], + &ep[i].reserved[j], (unsigned long long)dma, - ctx->ep[i].reserved[j], j); + ep[i].reserved[j], j); dma += field_size; } } + return dma; +} + +void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep) +{ + int i; + /* Fields are 32 bits wide, DMA addresses are in bytes */ + int field_size = 32 / 8; + + xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - drop flags\n", + &ctx->drop_flags, (unsigned long long)dma, + ctx->drop_flags); + dma += field_size; + xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - add flags\n", + &ctx->add_flags, (unsigned long long)dma, + ctx->add_flags); + dma += field_size; + for (i = 0; i < 6; ++i) { + xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n", + &ctx->rsvd[i], (unsigned long long)dma, + ctx->rsvd[i], i); + dma += field_size; + } + dma = xhci_dbg_slot_ctx(xhci, &ctx->slot, dma); + dma = xhci_dbg_ep_ctx(xhci, ctx->ep, dma, last_ep); +} + +void xhci_dbg_device_ctx(struct xhci_hcd *xhci, struct xhci_device_ctx *ctx, dma_addr_t dma, unsigned int last_ep) +{ + dma = xhci_dbg_slot_ctx(xhci, &ctx->slot, dma); + dma = xhci_dbg_ep_ctx(xhci, ctx->ep, dma, last_ep); } diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index 008326d5bc5..921dd173d79 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -1013,7 +1013,7 @@ int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev) } xhci_dbg(xhci, "Output context after successful config ep cmd:\n"); - xhci_dbg_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, + xhci_dbg_device_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, LAST_CTX_TO_EP_NUM(virt_dev->in_ctx->slot.dev_info)); xhci_zero_in_ctx(virt_dev); @@ -1265,7 +1265,7 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id); xhci_dbg_ctx(xhci, virt_dev->in_ctx, virt_dev->in_ctx_dma, 2); xhci_dbg(xhci, "Slot ID %d Output Context:\n", udev->slot_id); - xhci_dbg_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, 2); + xhci_dbg_device_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, 2); /* * USB core uses address 1 for the roothubs, so we add one to the * address given back to us by the HC. @@ -1274,9 +1274,6 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) /* Zero the input context control for later use */ virt_dev->in_ctx->add_flags = 0; virt_dev->in_ctx->drop_flags = 0; - /* Mirror flags in the output context for future ep enable/disable */ - virt_dev->out_ctx->add_flags = SLOT_FLAG | EP0_FLAG; - virt_dev->out_ctx->drop_flags = 0; xhci_dbg(xhci, "Device address = %d\n", udev->devnum); /* XXX Meh, not sure if anyone else but choose_address uses this. */ diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index 71121d99235..8d6bdf2f801 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -235,7 +235,10 @@ int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id, return 0; dev = xhci->devs[slot_id]; - /* Allocate the (output) device context that will be used in the HC */ + /* Allocate the (output) device context that will be used in the HC. + * The structure is 32 bytes smaller than the input context, but that's + * fine. + */ dev->out_ctx = dma_pool_alloc(xhci->device_pool, flags, &dma); if (!dev->out_ctx) goto fail; @@ -260,16 +263,12 @@ int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id, init_completion(&dev->cmd_completion); - /* - * Point to output device context in dcbaa; skip the output control - * context, which is eight 32 bit fields (or 32 bytes long) - */ - xhci->dcbaa->dev_context_ptrs[slot_id] = - (u32) dev->out_ctx_dma + (32); + /* Point to output device context in dcbaa. */ + xhci->dcbaa->dev_context_ptrs[slot_id] = dev->out_ctx_dma; xhci_dbg(xhci, "Set slot id %d dcbaa entry %p to 0x%llx\n", slot_id, &xhci->dcbaa->dev_context_ptrs[slot_id], - (unsigned long long)dev->out_ctx_dma); + (unsigned long long) xhci->dcbaa->dev_context_ptrs[slot_id]); return 1; fail: diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 5a09b9a26e0..d4d3c7777fb 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -584,15 +584,29 @@ struct xhci_ep_ctx { /** * struct xhci_device_control - * Input/Output context; see section 6.2.5. + * Input context; see section 6.2.5. * * @drop_context: set the bit of the endpoint context you want to disable * @add_context: set the bit of the endpoint context you want to enable */ struct xhci_device_control { + /* Input control context */ u32 drop_flags; u32 add_flags; u32 rsvd[6]; + /* Copy of device context */ + struct xhci_slot_ctx slot; + struct xhci_ep_ctx ep[31]; +}; + +/** + * struct xhci_device_ctx + * Device context; see section 6.2.1. + * + * @slot: slot context for the device. + * @ep: array of endpoint contexts for the device. + */ +struct xhci_device_ctx { struct xhci_slot_ctx slot; struct xhci_ep_ctx ep[31]; }; @@ -612,7 +626,7 @@ struct xhci_virt_device { * track of input and output contexts separately because * these commands might fail and we don't trust the hardware. */ - struct xhci_device_control *out_ctx; + struct xhci_device_ctx *out_ctx; dma_addr_t out_ctx_dma; /* Used for addressing devices and configuration changes */ struct xhci_device_control *in_ctx; @@ -1126,6 +1140,7 @@ void xhci_dbg_erst(struct xhci_hcd *xhci, struct xhci_erst *erst); void xhci_dbg_cmd_ptrs(struct xhci_hcd *xhci); void xhci_dbg_ring_ptrs(struct xhci_hcd *xhci, struct xhci_ring *ring); void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep); +void xhci_dbg_device_ctx(struct xhci_hcd *xhci, struct xhci_device_ctx *ctx, dma_addr_t dma, unsigned int last_ep); /* xHCI memory managment */ void xhci_mem_cleanup(struct xhci_hcd *xhci); -- GitLab From d115b04818e57bdbc7ccde4d0660b15e33013dc8 Mon Sep 17 00:00:00 2001 From: John Youn Date: Mon, 27 Jul 2009 12:05:15 -0700 Subject: [PATCH 0449/1342] USB: xhci: Support for 64-byte contexts Adds support for controllers that use 64-byte contexts. The following context data structures are affected by this: Device, Input, Input Control, Endpoint, and Slot. To accommodate the use of either 32 or 64-byte contexts, a Device or Input context can only be accessed through functions which look-up and return pointers to their contained contexts. Signed-off-by: John Youn Acked-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-dbg.c | 125 ++++++++++++++++++++++------------- drivers/usb/host/xhci-hcd.c | 121 +++++++++++++++++++-------------- drivers/usb/host/xhci-mem.c | 121 +++++++++++++++++++++++---------- drivers/usb/host/xhci-ring.c | 22 ++++-- drivers/usb/host/xhci.h | 61 +++++++++-------- 5 files changed, 287 insertions(+), 163 deletions(-) diff --git a/drivers/usb/host/xhci-dbg.c b/drivers/usb/host/xhci-dbg.c index d77f8de1125..705e3432415 100644 --- a/drivers/usb/host/xhci-dbg.c +++ b/drivers/usb/host/xhci-dbg.c @@ -393,103 +393,138 @@ void xhci_dbg_cmd_ptrs(struct xhci_hcd *xhci) upper_32_bits(val)); } -dma_addr_t xhci_dbg_slot_ctx(struct xhci_hcd *xhci, struct xhci_slot_ctx *slot, dma_addr_t dma) +/* Print the last 32 bytes for 64-byte contexts */ +static void dbg_rsvd64(struct xhci_hcd *xhci, u64 *ctx, dma_addr_t dma) +{ + int i; + for (i = 0; i < 4; ++i) { + xhci_dbg(xhci, "@%p (virt) @%08llx " + "(dma) %#08llx - rsvd64[%d]\n", + &ctx[4 + i], (unsigned long long)dma, + ctx[4 + i], i); + dma += 8; + } +} + +void xhci_dbg_slot_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx) { /* Fields are 32 bits wide, DMA addresses are in bytes */ int field_size = 32 / 8; int i; + struct xhci_slot_ctx *slot_ctx = xhci_get_slot_ctx(xhci, ctx); + dma_addr_t dma = ctx->dma + ((unsigned long)slot_ctx - (unsigned long)ctx); + int csz = HCC_64BYTE_CONTEXT(xhci->hcc_params); + xhci_dbg(xhci, "Slot Context:\n"); xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_info\n", - &slot->dev_info, - (unsigned long long)dma, slot->dev_info); + &slot_ctx->dev_info, + (unsigned long long)dma, slot_ctx->dev_info); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_info2\n", - &slot->dev_info2, - (unsigned long long)dma, slot->dev_info2); + &slot_ctx->dev_info2, + (unsigned long long)dma, slot_ctx->dev_info2); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - tt_info\n", - &slot->tt_info, - (unsigned long long)dma, slot->tt_info); + &slot_ctx->tt_info, + (unsigned long long)dma, slot_ctx->tt_info); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_state\n", - &slot->dev_state, - (unsigned long long)dma, slot->dev_state); + &slot_ctx->dev_state, + (unsigned long long)dma, slot_ctx->dev_state); dma += field_size; for (i = 0; i < 4; ++i) { xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n", - &slot->reserved[i], (unsigned long long)dma, - slot->reserved[i], i); + &slot_ctx->reserved[i], (unsigned long long)dma, + slot_ctx->reserved[i], i); dma += field_size; } - return dma; + if (csz) + dbg_rsvd64(xhci, (u64 *)slot_ctx, dma); } -dma_addr_t xhci_dbg_ep_ctx(struct xhci_hcd *xhci, struct xhci_ep_ctx *ep, dma_addr_t dma, unsigned int last_ep) +void xhci_dbg_ep_ctx(struct xhci_hcd *xhci, + struct xhci_container_ctx *ctx, + unsigned int last_ep) { int i, j; int last_ep_ctx = 31; /* Fields are 32 bits wide, DMA addresses are in bytes */ int field_size = 32 / 8; + int csz = HCC_64BYTE_CONTEXT(xhci->hcc_params); if (last_ep < 31) last_ep_ctx = last_ep + 1; for (i = 0; i < last_ep_ctx; ++i) { + struct xhci_ep_ctx *ep_ctx = xhci_get_ep_ctx(xhci, ctx, i); + dma_addr_t dma = ctx->dma + + ((unsigned long)ep_ctx - (unsigned long)ctx); + xhci_dbg(xhci, "Endpoint %02d Context:\n", i); xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - ep_info\n", - &ep[i].ep_info, - (unsigned long long)dma, ep[i].ep_info); + &ep_ctx->ep_info, + (unsigned long long)dma, ep_ctx->ep_info); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - ep_info2\n", - &ep[i].ep_info2, - (unsigned long long)dma, ep[i].ep_info2); + &ep_ctx->ep_info2, + (unsigned long long)dma, ep_ctx->ep_info2); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08llx - deq\n", - &ep[i].deq, - (unsigned long long)dma, ep[i].deq); + &ep_ctx->deq, + (unsigned long long)dma, ep_ctx->deq); dma += 2*field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - tx_info\n", - &ep[i].tx_info, - (unsigned long long)dma, ep[i].tx_info); + &ep_ctx->tx_info, + (unsigned long long)dma, ep_ctx->tx_info); dma += field_size; for (j = 0; j < 3; ++j) { xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n", - &ep[i].reserved[j], + &ep_ctx->reserved[j], (unsigned long long)dma, - ep[i].reserved[j], j); + ep_ctx->reserved[j], j); dma += field_size; } + + if (csz) + dbg_rsvd64(xhci, (u64 *)ep_ctx, dma); } - return dma; } -void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep) +void xhci_dbg_ctx(struct xhci_hcd *xhci, + struct xhci_container_ctx *ctx, + unsigned int last_ep) { int i; /* Fields are 32 bits wide, DMA addresses are in bytes */ int field_size = 32 / 8; - - xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - drop flags\n", - &ctx->drop_flags, (unsigned long long)dma, - ctx->drop_flags); - dma += field_size; - xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - add flags\n", - &ctx->add_flags, (unsigned long long)dma, - ctx->add_flags); - dma += field_size; - for (i = 0; i < 6; ++i) { - xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n", - &ctx->rsvd[i], (unsigned long long)dma, - ctx->rsvd[i], i); + struct xhci_slot_ctx *slot_ctx; + dma_addr_t dma = ctx->dma; + int csz = HCC_64BYTE_CONTEXT(xhci->hcc_params); + + if (ctx->type == XHCI_CTX_TYPE_INPUT) { + struct xhci_input_control_ctx *ctrl_ctx = + xhci_get_input_control_ctx(xhci, ctx); + xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - drop flags\n", + &ctrl_ctx->drop_flags, (unsigned long long)dma, + ctrl_ctx->drop_flags); dma += field_size; + xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - add flags\n", + &ctrl_ctx->add_flags, (unsigned long long)dma, + ctrl_ctx->add_flags); + dma += field_size; + for (i = 0; i < 6; ++i) { + xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd2[%d]\n", + &ctrl_ctx->rsvd2[i], (unsigned long long)dma, + ctrl_ctx->rsvd2[i], i); + dma += field_size; + } + + if (csz) + dbg_rsvd64(xhci, (u64 *)ctrl_ctx, dma); } - dma = xhci_dbg_slot_ctx(xhci, &ctx->slot, dma); - dma = xhci_dbg_ep_ctx(xhci, ctx->ep, dma, last_ep); -} -void xhci_dbg_device_ctx(struct xhci_hcd *xhci, struct xhci_device_ctx *ctx, dma_addr_t dma, unsigned int last_ep) -{ - dma = xhci_dbg_slot_ctx(xhci, &ctx->slot, dma); - dma = xhci_dbg_ep_ctx(xhci, ctx->ep, dma, last_ep); + slot_ctx = xhci_get_slot_ctx(xhci, ctx); + xhci_dbg_slot_ctx(xhci, ctx); + xhci_dbg_ep_ctx(xhci, ctx, last_ep); } diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index 921dd173d79..057a07e876b 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -722,7 +722,9 @@ int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev, struct usb_host_endpoint *ep) { struct xhci_hcd *xhci; - struct xhci_device_control *in_ctx; + struct xhci_container_ctx *in_ctx, *out_ctx; + struct xhci_input_control_ctx *ctrl_ctx; + struct xhci_slot_ctx *slot_ctx; unsigned int last_ctx; unsigned int ep_index; struct xhci_ep_ctx *ep_ctx; @@ -750,31 +752,34 @@ int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev, } in_ctx = xhci->devs[udev->slot_id]->in_ctx; + out_ctx = xhci->devs[udev->slot_id]->out_ctx; + ctrl_ctx = xhci_get_input_control_ctx(xhci, in_ctx); ep_index = xhci_get_endpoint_index(&ep->desc); - ep_ctx = &xhci->devs[udev->slot_id]->out_ctx->ep[ep_index]; + ep_ctx = xhci_get_ep_ctx(xhci, out_ctx, ep_index); /* If the HC already knows the endpoint is disabled, * or the HCD has noted it is disabled, ignore this request */ if ((ep_ctx->ep_info & EP_STATE_MASK) == EP_STATE_DISABLED || - in_ctx->drop_flags & xhci_get_endpoint_flag(&ep->desc)) { + ctrl_ctx->drop_flags & xhci_get_endpoint_flag(&ep->desc)) { xhci_warn(xhci, "xHCI %s called with disabled ep %p\n", __func__, ep); return 0; } - in_ctx->drop_flags |= drop_flag; - new_drop_flags = in_ctx->drop_flags; + ctrl_ctx->drop_flags |= drop_flag; + new_drop_flags = ctrl_ctx->drop_flags; - in_ctx->add_flags = ~drop_flag; - new_add_flags = in_ctx->add_flags; + ctrl_ctx->add_flags = ~drop_flag; + new_add_flags = ctrl_ctx->add_flags; - last_ctx = xhci_last_valid_endpoint(in_ctx->add_flags); + last_ctx = xhci_last_valid_endpoint(ctrl_ctx->add_flags); + slot_ctx = xhci_get_slot_ctx(xhci, in_ctx); /* Update the last valid endpoint context, if we deleted the last one */ - if ((in_ctx->slot.dev_info & LAST_CTX_MASK) > LAST_CTX(last_ctx)) { - in_ctx->slot.dev_info &= ~LAST_CTX_MASK; - in_ctx->slot.dev_info |= LAST_CTX(last_ctx); + if ((slot_ctx->dev_info & LAST_CTX_MASK) > LAST_CTX(last_ctx)) { + slot_ctx->dev_info &= ~LAST_CTX_MASK; + slot_ctx->dev_info |= LAST_CTX(last_ctx); } - new_slot_info = in_ctx->slot.dev_info; + new_slot_info = slot_ctx->dev_info; xhci_endpoint_zero(xhci, xhci->devs[udev->slot_id], ep); @@ -804,9 +809,11 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, struct usb_host_endpoint *ep) { struct xhci_hcd *xhci; - struct xhci_device_control *in_ctx; + struct xhci_container_ctx *in_ctx, *out_ctx; unsigned int ep_index; struct xhci_ep_ctx *ep_ctx; + struct xhci_slot_ctx *slot_ctx; + struct xhci_input_control_ctx *ctrl_ctx; u32 added_ctxs; unsigned int last_ctx; u32 new_add_flags, new_drop_flags, new_slot_info; @@ -839,12 +846,14 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, } in_ctx = xhci->devs[udev->slot_id]->in_ctx; + out_ctx = xhci->devs[udev->slot_id]->out_ctx; + ctrl_ctx = xhci_get_input_control_ctx(xhci, in_ctx); ep_index = xhci_get_endpoint_index(&ep->desc); - ep_ctx = &xhci->devs[udev->slot_id]->out_ctx->ep[ep_index]; + ep_ctx = xhci_get_ep_ctx(xhci, out_ctx, ep_index); /* If the HCD has already noted the endpoint is enabled, * ignore this request. */ - if (in_ctx->add_flags & xhci_get_endpoint_flag(&ep->desc)) { + if (ctrl_ctx->add_flags & xhci_get_endpoint_flag(&ep->desc)) { xhci_warn(xhci, "xHCI %s called with enabled ep %p\n", __func__, ep); return 0; @@ -862,8 +871,8 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, return -ENOMEM; } - in_ctx->add_flags |= added_ctxs; - new_add_flags = in_ctx->add_flags; + ctrl_ctx->add_flags |= added_ctxs; + new_add_flags = ctrl_ctx->add_flags; /* If xhci_endpoint_disable() was called for this endpoint, but the * xHC hasn't been notified yet through the check_bandwidth() call, @@ -871,14 +880,15 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, * descriptors. We must drop and re-add this endpoint, so we leave the * drop flags alone. */ - new_drop_flags = in_ctx->drop_flags; + new_drop_flags = ctrl_ctx->drop_flags; + slot_ctx = xhci_get_slot_ctx(xhci, in_ctx); /* Update the last valid endpoint context, if we just added one past */ - if ((in_ctx->slot.dev_info & LAST_CTX_MASK) < LAST_CTX(last_ctx)) { - in_ctx->slot.dev_info &= ~LAST_CTX_MASK; - in_ctx->slot.dev_info |= LAST_CTX(last_ctx); + if ((slot_ctx->dev_info & LAST_CTX_MASK) < LAST_CTX(last_ctx)) { + slot_ctx->dev_info &= ~LAST_CTX_MASK; + slot_ctx->dev_info |= LAST_CTX(last_ctx); } - new_slot_info = in_ctx->slot.dev_info; + new_slot_info = slot_ctx->dev_info; /* Store the usb_device pointer for later use */ ep->hcpriv = udev; @@ -892,9 +902,11 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, return 0; } -static void xhci_zero_in_ctx(struct xhci_virt_device *virt_dev) +static void xhci_zero_in_ctx(struct xhci_hcd *xhci, struct xhci_virt_device *virt_dev) { + struct xhci_input_control_ctx *ctrl_ctx; struct xhci_ep_ctx *ep_ctx; + struct xhci_slot_ctx *slot_ctx; int i; /* When a device's add flag and drop flag are zero, any subsequent @@ -902,13 +914,15 @@ static void xhci_zero_in_ctx(struct xhci_virt_device *virt_dev) * untouched. Make sure we don't leave any old state in the input * endpoint contexts. */ - virt_dev->in_ctx->drop_flags = 0; - virt_dev->in_ctx->add_flags = 0; - virt_dev->in_ctx->slot.dev_info &= ~LAST_CTX_MASK; + ctrl_ctx = xhci_get_input_control_ctx(xhci, virt_dev->in_ctx); + ctrl_ctx->drop_flags = 0; + ctrl_ctx->add_flags = 0; + slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx); + slot_ctx->dev_info &= ~LAST_CTX_MASK; /* Endpoint 0 is always valid */ - virt_dev->in_ctx->slot.dev_info |= LAST_CTX(1); + slot_ctx->dev_info |= LAST_CTX(1); for (i = 1; i < 31; ++i) { - ep_ctx = &virt_dev->in_ctx->ep[i]; + ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, i); ep_ctx->ep_info = 0; ep_ctx->ep_info2 = 0; ep_ctx->deq = 0; @@ -934,6 +948,8 @@ int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev) unsigned long flags; struct xhci_hcd *xhci; struct xhci_virt_device *virt_dev; + struct xhci_input_control_ctx *ctrl_ctx; + struct xhci_slot_ctx *slot_ctx; ret = xhci_check_args(hcd, udev, NULL, 0, __func__); if (ret <= 0) @@ -949,16 +965,18 @@ int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev) virt_dev = xhci->devs[udev->slot_id]; /* See section 4.6.6 - A0 = 1; A1 = D0 = D1 = 0 */ - virt_dev->in_ctx->add_flags |= SLOT_FLAG; - virt_dev->in_ctx->add_flags &= ~EP0_FLAG; - virt_dev->in_ctx->drop_flags &= ~SLOT_FLAG; - virt_dev->in_ctx->drop_flags &= ~EP0_FLAG; + ctrl_ctx = xhci_get_input_control_ctx(xhci, virt_dev->in_ctx); + ctrl_ctx->add_flags |= SLOT_FLAG; + ctrl_ctx->add_flags &= ~EP0_FLAG; + ctrl_ctx->drop_flags &= ~SLOT_FLAG; + ctrl_ctx->drop_flags &= ~EP0_FLAG; xhci_dbg(xhci, "New Input Control Context:\n"); - xhci_dbg_ctx(xhci, virt_dev->in_ctx, virt_dev->in_ctx_dma, - LAST_CTX_TO_EP_NUM(virt_dev->in_ctx->slot.dev_info)); + slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx); + xhci_dbg_ctx(xhci, virt_dev->in_ctx, + LAST_CTX_TO_EP_NUM(slot_ctx->dev_info)); spin_lock_irqsave(&xhci->lock, flags); - ret = xhci_queue_configure_endpoint(xhci, virt_dev->in_ctx_dma, + ret = xhci_queue_configure_endpoint(xhci, virt_dev->in_ctx->dma, udev->slot_id); if (ret < 0) { spin_unlock_irqrestore(&xhci->lock, flags); @@ -1013,10 +1031,10 @@ int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev) } xhci_dbg(xhci, "Output context after successful config ep cmd:\n"); - xhci_dbg_device_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, - LAST_CTX_TO_EP_NUM(virt_dev->in_ctx->slot.dev_info)); + xhci_dbg_ctx(xhci, virt_dev->out_ctx, + LAST_CTX_TO_EP_NUM(slot_ctx->dev_info)); - xhci_zero_in_ctx(virt_dev); + xhci_zero_in_ctx(xhci, virt_dev); /* Free any old rings */ for (i = 1; i < 31; ++i) { if (virt_dev->new_ep_rings[i]) { @@ -1054,7 +1072,7 @@ void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev) virt_dev->new_ep_rings[i] = NULL; } } - xhci_zero_in_ctx(virt_dev); + xhci_zero_in_ctx(xhci, virt_dev); } /* Deal with stalled endpoints. The core should have sent the control message @@ -1187,6 +1205,8 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) struct xhci_virt_device *virt_dev; int ret = 0; struct xhci_hcd *xhci = hcd_to_xhci(hcd); + struct xhci_slot_ctx *slot_ctx; + struct xhci_input_control_ctx *ctrl_ctx; u64 temp_64; if (!udev->slot_id) { @@ -1201,11 +1221,11 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) xhci_setup_addressable_virt_dev(xhci, udev); /* Otherwise, assume the core has the device configured how it wants */ xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id); - xhci_dbg_ctx(xhci, virt_dev->in_ctx, virt_dev->in_ctx_dma, 2); + xhci_dbg_ctx(xhci, virt_dev->in_ctx, 2); spin_lock_irqsave(&xhci->lock, flags); - ret = xhci_queue_address_device(xhci, virt_dev->in_ctx_dma, - udev->slot_id); + ret = xhci_queue_address_device(xhci, virt_dev->in_ctx->dma, + udev->slot_id); if (ret) { spin_unlock_irqrestore(&xhci->lock, flags); xhci_dbg(xhci, "FIXME: allocate a command ring segment\n"); @@ -1246,7 +1266,7 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) xhci_err(xhci, "ERROR: unexpected command completion " "code 0x%x.\n", virt_dev->cmd_status); xhci_dbg(xhci, "Slot ID %d Output Context:\n", udev->slot_id); - xhci_dbg_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, 2); + xhci_dbg_ctx(xhci, virt_dev->out_ctx, 2); ret = -EINVAL; break; } @@ -1261,19 +1281,21 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) (unsigned long long) xhci->dcbaa->dev_context_ptrs[udev->slot_id]); xhci_dbg(xhci, "Output Context DMA address = %#08llx\n", - (unsigned long long)virt_dev->out_ctx_dma); + (unsigned long long)virt_dev->out_ctx->dma); xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id); - xhci_dbg_ctx(xhci, virt_dev->in_ctx, virt_dev->in_ctx_dma, 2); + xhci_dbg_ctx(xhci, virt_dev->in_ctx, 2); xhci_dbg(xhci, "Slot ID %d Output Context:\n", udev->slot_id); - xhci_dbg_device_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, 2); + xhci_dbg_ctx(xhci, virt_dev->out_ctx, 2); /* * USB core uses address 1 for the roothubs, so we add one to the * address given back to us by the HC. */ - udev->devnum = (virt_dev->out_ctx->slot.dev_state & DEV_ADDR_MASK) + 1; + slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->out_ctx); + udev->devnum = (slot_ctx->dev_state & DEV_ADDR_MASK) + 1; /* Zero the input context control for later use */ - virt_dev->in_ctx->add_flags = 0; - virt_dev->in_ctx->drop_flags = 0; + ctrl_ctx = xhci_get_input_control_ctx(xhci, virt_dev->in_ctx); + ctrl_ctx->add_flags = 0; + ctrl_ctx->drop_flags = 0; xhci_dbg(xhci, "Device address = %d\n", udev->devnum); /* XXX Meh, not sure if anyone else but choose_address uses this. */ @@ -1315,7 +1337,6 @@ static int __init xhci_hcd_init(void) /* xhci_device_control has eight fields, and also * embeds one xhci_slot_ctx and 31 xhci_ep_ctx */ - BUILD_BUG_ON(sizeof(struct xhci_device_control) != (8+8+8*31)*32/8); BUILD_BUG_ON(sizeof(struct xhci_stream_ctx) != 4*32/8); BUILD_BUG_ON(sizeof(union xhci_trb) != 4*32/8); BUILD_BUG_ON(sizeof(struct xhci_erst_entry) != 4*32/8); diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index 8d6bdf2f801..e6b9a1c6002 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -189,6 +189,63 @@ fail: return 0; } +#define CTX_SIZE(_hcc) (HCC_64BYTE_CONTEXT(_hcc) ? 64 : 32) + +struct xhci_container_ctx *xhci_alloc_container_ctx(struct xhci_hcd *xhci, + int type, gfp_t flags) +{ + struct xhci_container_ctx *ctx = kzalloc(sizeof(*ctx), flags); + if (!ctx) + return NULL; + + BUG_ON((type != XHCI_CTX_TYPE_DEVICE) && (type != XHCI_CTX_TYPE_INPUT)); + ctx->type = type; + ctx->size = HCC_64BYTE_CONTEXT(xhci->hcc_params) ? 2048 : 1024; + if (type == XHCI_CTX_TYPE_INPUT) + ctx->size += CTX_SIZE(xhci->hcc_params); + + ctx->bytes = dma_pool_alloc(xhci->device_pool, flags, &ctx->dma); + memset(ctx->bytes, 0, ctx->size); + return ctx; +} + +void xhci_free_container_ctx(struct xhci_hcd *xhci, + struct xhci_container_ctx *ctx) +{ + dma_pool_free(xhci->device_pool, ctx->bytes, ctx->dma); + kfree(ctx); +} + +struct xhci_input_control_ctx *xhci_get_input_control_ctx(struct xhci_hcd *xhci, + struct xhci_container_ctx *ctx) +{ + BUG_ON(ctx->type != XHCI_CTX_TYPE_INPUT); + return (struct xhci_input_control_ctx *)ctx->bytes; +} + +struct xhci_slot_ctx *xhci_get_slot_ctx(struct xhci_hcd *xhci, + struct xhci_container_ctx *ctx) +{ + if (ctx->type == XHCI_CTX_TYPE_DEVICE) + return (struct xhci_slot_ctx *)ctx->bytes; + + return (struct xhci_slot_ctx *) + (ctx->bytes + CTX_SIZE(xhci->hcc_params)); +} + +struct xhci_ep_ctx *xhci_get_ep_ctx(struct xhci_hcd *xhci, + struct xhci_container_ctx *ctx, + unsigned int ep_index) +{ + /* increment ep index by offset of start of ep ctx array */ + ep_index++; + if (ctx->type == XHCI_CTX_TYPE_INPUT) + ep_index++; + + return (struct xhci_ep_ctx *) + (ctx->bytes + (ep_index * CTX_SIZE(xhci->hcc_params))); +} + /* All the xhci_tds in the ring's TD list should be freed at this point */ void xhci_free_virt_device(struct xhci_hcd *xhci, int slot_id) { @@ -209,11 +266,10 @@ void xhci_free_virt_device(struct xhci_hcd *xhci, int slot_id) xhci_ring_free(xhci, dev->ep_rings[i]); if (dev->in_ctx) - dma_pool_free(xhci->device_pool, - dev->in_ctx, dev->in_ctx_dma); + xhci_free_container_ctx(xhci, dev->in_ctx); if (dev->out_ctx) - dma_pool_free(xhci->device_pool, - dev->out_ctx, dev->out_ctx_dma); + xhci_free_container_ctx(xhci, dev->out_ctx); + kfree(xhci->devs[slot_id]); xhci->devs[slot_id] = 0; } @@ -221,7 +277,6 @@ void xhci_free_virt_device(struct xhci_hcd *xhci, int slot_id) int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id, struct usb_device *udev, gfp_t flags) { - dma_addr_t dma; struct xhci_virt_device *dev; /* Slot ID 0 is reserved */ @@ -235,26 +290,21 @@ int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id, return 0; dev = xhci->devs[slot_id]; - /* Allocate the (output) device context that will be used in the HC. - * The structure is 32 bytes smaller than the input context, but that's - * fine. - */ - dev->out_ctx = dma_pool_alloc(xhci->device_pool, flags, &dma); + /* Allocate the (output) device context that will be used in the HC. */ + dev->out_ctx = xhci_alloc_container_ctx(xhci, XHCI_CTX_TYPE_DEVICE, flags); if (!dev->out_ctx) goto fail; - dev->out_ctx_dma = dma; + xhci_dbg(xhci, "Slot %d output ctx = 0x%llx (dma)\n", slot_id, - (unsigned long long)dma); - memset(dev->out_ctx, 0, sizeof(*dev->out_ctx)); + (unsigned long long)dev->out_ctx->dma); /* Allocate the (input) device context for address device command */ - dev->in_ctx = dma_pool_alloc(xhci->device_pool, flags, &dma); + dev->in_ctx = xhci_alloc_container_ctx(xhci, XHCI_CTX_TYPE_INPUT, flags); if (!dev->in_ctx) goto fail; - dev->in_ctx_dma = dma; + xhci_dbg(xhci, "Slot %d input ctx = 0x%llx (dma)\n", slot_id, - (unsigned long long)dma); - memset(dev->in_ctx, 0, sizeof(*dev->in_ctx)); + (unsigned long long)dev->in_ctx->dma); /* Allocate endpoint 0 ring */ dev->ep_rings[0] = xhci_ring_alloc(xhci, 1, true, flags); @@ -264,7 +314,7 @@ int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id, init_completion(&dev->cmd_completion); /* Point to output device context in dcbaa. */ - xhci->dcbaa->dev_context_ptrs[slot_id] = dev->out_ctx_dma; + xhci->dcbaa->dev_context_ptrs[slot_id] = dev->out_ctx->dma; xhci_dbg(xhci, "Set slot id %d dcbaa entry %p to 0x%llx\n", slot_id, &xhci->dcbaa->dev_context_ptrs[slot_id], @@ -282,6 +332,8 @@ int xhci_setup_addressable_virt_dev(struct xhci_hcd *xhci, struct usb_device *ud struct xhci_virt_device *dev; struct xhci_ep_ctx *ep0_ctx; struct usb_device *top_dev; + struct xhci_slot_ctx *slot_ctx; + struct xhci_input_control_ctx *ctrl_ctx; dev = xhci->devs[udev->slot_id]; /* Slot ID 0 is reserved */ @@ -290,27 +342,29 @@ int xhci_setup_addressable_virt_dev(struct xhci_hcd *xhci, struct usb_device *ud udev->slot_id); return -EINVAL; } - ep0_ctx = &dev->in_ctx->ep[0]; + ep0_ctx = xhci_get_ep_ctx(xhci, dev->in_ctx, 0); + ctrl_ctx = xhci_get_input_control_ctx(xhci, dev->in_ctx); + slot_ctx = xhci_get_slot_ctx(xhci, dev->in_ctx); /* 2) New slot context and endpoint 0 context are valid*/ - dev->in_ctx->add_flags = SLOT_FLAG | EP0_FLAG; + ctrl_ctx->add_flags = SLOT_FLAG | EP0_FLAG; /* 3) Only the control endpoint is valid - one endpoint context */ - dev->in_ctx->slot.dev_info |= LAST_CTX(1); + slot_ctx->dev_info |= LAST_CTX(1); switch (udev->speed) { case USB_SPEED_SUPER: - dev->in_ctx->slot.dev_info |= (u32) udev->route; - dev->in_ctx->slot.dev_info |= (u32) SLOT_SPEED_SS; + slot_ctx->dev_info |= (u32) udev->route; + slot_ctx->dev_info |= (u32) SLOT_SPEED_SS; break; case USB_SPEED_HIGH: - dev->in_ctx->slot.dev_info |= (u32) SLOT_SPEED_HS; + slot_ctx->dev_info |= (u32) SLOT_SPEED_HS; break; case USB_SPEED_FULL: - dev->in_ctx->slot.dev_info |= (u32) SLOT_SPEED_FS; + slot_ctx->dev_info |= (u32) SLOT_SPEED_FS; break; case USB_SPEED_LOW: - dev->in_ctx->slot.dev_info |= (u32) SLOT_SPEED_LS; + slot_ctx->dev_info |= (u32) SLOT_SPEED_LS; break; case USB_SPEED_VARIABLE: xhci_dbg(xhci, "FIXME xHCI doesn't support wireless speeds\n"); @@ -324,7 +378,7 @@ int xhci_setup_addressable_virt_dev(struct xhci_hcd *xhci, struct usb_device *ud for (top_dev = udev; top_dev->parent && top_dev->parent->parent; top_dev = top_dev->parent) /* Found device below root hub */; - dev->in_ctx->slot.dev_info2 |= (u32) ROOT_HUB_PORT(top_dev->portnum); + slot_ctx->dev_info2 |= (u32) ROOT_HUB_PORT(top_dev->portnum); xhci_dbg(xhci, "Set root hub portnum to %d\n", top_dev->portnum); /* Is this a LS/FS device under a HS hub? */ @@ -334,8 +388,8 @@ int xhci_setup_addressable_virt_dev(struct xhci_hcd *xhci, struct usb_device *ud */ if ((udev->speed == USB_SPEED_LOW || udev->speed == USB_SPEED_FULL) && udev->tt) { - dev->in_ctx->slot.tt_info = udev->tt->hub->slot_id; - dev->in_ctx->slot.tt_info |= udev->ttport << 8; + slot_ctx->tt_info = udev->tt->hub->slot_id; + slot_ctx->tt_info |= udev->ttport << 8; } xhci_dbg(xhci, "udev->tt = %p\n", udev->tt); xhci_dbg(xhci, "udev->ttport = 0x%x\n", udev->ttport); @@ -466,7 +520,7 @@ int xhci_endpoint_init(struct xhci_hcd *xhci, unsigned int max_burst; ep_index = xhci_get_endpoint_index(&ep->desc); - ep_ctx = &virt_dev->in_ctx->ep[ep_index]; + ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index); /* Set up the endpoint ring */ virt_dev->new_ep_rings[ep_index] = xhci_ring_alloc(xhci, 1, true, mem_flags); @@ -533,7 +587,7 @@ void xhci_endpoint_zero(struct xhci_hcd *xhci, struct xhci_ep_ctx *ep_ctx; ep_index = xhci_get_endpoint_index(&ep->desc); - ep_ctx = &virt_dev->in_ctx->ep[ep_index]; + ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index); ep_ctx->ep_info = 0; ep_ctx->ep_info2 = 0; @@ -753,11 +807,10 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) */ xhci->segment_pool = dma_pool_create("xHCI ring segments", dev, SEGMENT_SIZE, 64, xhci->page_size); + /* See Table 46 and Note on Figure 55 */ - /* FIXME support 64-byte contexts */ xhci->device_pool = dma_pool_create("xHCI input/output contexts", dev, - sizeof(struct xhci_device_control), - 64, xhci->page_size); + 2112, 64, xhci->page_size); if (!xhci->segment_pool || !xhci->device_pool) goto fail; diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 0903e98989e..ea31753c313 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -362,6 +362,7 @@ static void find_new_dequeue_state(struct xhci_hcd *xhci, struct xhci_virt_device *dev = xhci->devs[slot_id]; struct xhci_ring *ep_ring = dev->ep_rings[ep_index]; struct xhci_generic_trb *trb; + struct xhci_ep_ctx *ep_ctx; state->new_cycle_state = 0; state->new_deq_seg = find_trb_seg(cur_td->start_seg, @@ -370,7 +371,8 @@ static void find_new_dequeue_state(struct xhci_hcd *xhci, if (!state->new_deq_seg) BUG(); /* Dig out the cycle state saved by the xHC during the stop ep cmd */ - state->new_cycle_state = 0x1 & dev->out_ctx->ep[ep_index].deq; + ep_ctx = xhci_get_ep_ctx(xhci, dev->out_ctx, ep_index); + state->new_cycle_state = 0x1 & ep_ctx->deq; state->new_deq_ptr = cur_td->last_trb; state->new_deq_seg = find_trb_seg(state->new_deq_seg, @@ -570,11 +572,15 @@ static void handle_set_deq_completion(struct xhci_hcd *xhci, unsigned int ep_index; struct xhci_ring *ep_ring; struct xhci_virt_device *dev; + struct xhci_ep_ctx *ep_ctx; + struct xhci_slot_ctx *slot_ctx; slot_id = TRB_TO_SLOT_ID(trb->generic.field[3]); ep_index = TRB_TO_EP_INDEX(trb->generic.field[3]); dev = xhci->devs[slot_id]; ep_ring = dev->ep_rings[ep_index]; + ep_ctx = xhci_get_ep_ctx(xhci, dev->out_ctx, ep_index); + slot_ctx = xhci_get_slot_ctx(xhci, dev->out_ctx); if (GET_COMP_CODE(event->status) != COMP_SUCCESS) { unsigned int ep_state; @@ -588,9 +594,9 @@ static void handle_set_deq_completion(struct xhci_hcd *xhci, case COMP_CTX_STATE: xhci_warn(xhci, "WARN Set TR Deq Ptr cmd failed due " "to incorrect slot or ep state.\n"); - ep_state = dev->out_ctx->ep[ep_index].ep_info; + ep_state = ep_ctx->ep_info; ep_state &= EP_STATE_MASK; - slot_state = dev->out_ctx->slot.dev_state; + slot_state = slot_ctx->dev_state; slot_state = GET_SLOT_STATE(slot_state); xhci_dbg(xhci, "Slot state = %u, EP state = %u\n", slot_state, ep_state); @@ -613,7 +619,7 @@ static void handle_set_deq_completion(struct xhci_hcd *xhci, */ } else { xhci_dbg(xhci, "Successful Set TR Deq Ptr cmd, deq = @%08llx\n", - dev->out_ctx->ep[ep_index].deq); + ep_ctx->deq); } ep_ring->state &= ~SET_DEQ_PENDING; @@ -795,6 +801,7 @@ static int handle_tx_event(struct xhci_hcd *xhci, union xhci_trb *event_trb; struct urb *urb = 0; int status = -EINPROGRESS; + struct xhci_ep_ctx *ep_ctx; xhci_dbg(xhci, "In %s\n", __func__); xdev = xhci->devs[TRB_TO_SLOT_ID(event->flags)]; @@ -807,7 +814,8 @@ static int handle_tx_event(struct xhci_hcd *xhci, ep_index = TRB_TO_EP_ID(event->flags) - 1; xhci_dbg(xhci, "%s - ep index = %d\n", __func__, ep_index); ep_ring = xdev->ep_rings[ep_index]; - if (!ep_ring || (xdev->out_ctx->ep[ep_index].ep_info & EP_STATE_MASK) == EP_STATE_DISABLED) { + ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index); + if (!ep_ring || (ep_ctx->ep_info & EP_STATE_MASK) == EP_STATE_DISABLED) { xhci_err(xhci, "ERROR Transfer event pointed to disabled endpoint\n"); return -ENODEV; } @@ -1193,9 +1201,9 @@ static int prepare_transfer(struct xhci_hcd *xhci, gfp_t mem_flags) { int ret; - + struct xhci_ep_ctx *ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index); ret = prepare_ring(xhci, xdev->ep_rings[ep_index], - xdev->out_ctx->ep[ep_index].ep_info & EP_STATE_MASK, + ep_ctx->ep_info & EP_STATE_MASK, num_trbs, mem_flags); if (ret) return ret; diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index d4d3c7777fb..9c108c63270 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -446,6 +446,27 @@ struct xhci_doorbell_array { #define EPI_TO_DB(p) (((p) + 1) & 0xff) +/** + * struct xhci_container_ctx + * @type: Type of context. Used to calculated offsets to contained contexts. + * @size: Size of the context data + * @bytes: The raw context data given to HW + * @dma: dma address of the bytes + * + * Represents either a Device or Input context. Holds a pointer to the raw + * memory used for the context (bytes) and dma address of it (dma). + */ +struct xhci_container_ctx { + unsigned type; +#define XHCI_CTX_TYPE_DEVICE 0x1 +#define XHCI_CTX_TYPE_INPUT 0x2 + + int size; + + u8 *bytes; + dma_addr_t dma; +}; + /** * struct xhci_slot_ctx * @dev_info: Route string, device speed, hub info, and last valid endpoint @@ -583,32 +604,16 @@ struct xhci_ep_ctx { /** - * struct xhci_device_control - * Input context; see section 6.2.5. + * struct xhci_input_control_context + * Input control context; see section 6.2.5. * * @drop_context: set the bit of the endpoint context you want to disable * @add_context: set the bit of the endpoint context you want to enable */ -struct xhci_device_control { - /* Input control context */ +struct xhci_input_control_ctx { u32 drop_flags; u32 add_flags; - u32 rsvd[6]; - /* Copy of device context */ - struct xhci_slot_ctx slot; - struct xhci_ep_ctx ep[31]; -}; - -/** - * struct xhci_device_ctx - * Device context; see section 6.2.1. - * - * @slot: slot context for the device. - * @ep: array of endpoint contexts for the device. - */ -struct xhci_device_ctx { - struct xhci_slot_ctx slot; - struct xhci_ep_ctx ep[31]; + u32 rsvd2[6]; }; /* drop context bitmasks */ @@ -616,7 +621,6 @@ struct xhci_device_ctx { /* add context bitmasks */ #define ADD_EP(x) (0x1 << x) - struct xhci_virt_device { /* * Commands to the hardware are passed an "input context" that @@ -626,11 +630,10 @@ struct xhci_virt_device { * track of input and output contexts separately because * these commands might fail and we don't trust the hardware. */ - struct xhci_device_ctx *out_ctx; - dma_addr_t out_ctx_dma; + struct xhci_container_ctx *out_ctx; /* Used for addressing devices and configuration changes */ - struct xhci_device_control *in_ctx; - dma_addr_t in_ctx_dma; + struct xhci_container_ctx *in_ctx; + /* FIXME when stream support is added */ struct xhci_ring *ep_rings[31]; /* Temporary storage in case the configure endpoint command fails and we @@ -1139,8 +1142,7 @@ void xhci_debug_ring(struct xhci_hcd *xhci, struct xhci_ring *ring); void xhci_dbg_erst(struct xhci_hcd *xhci, struct xhci_erst *erst); void xhci_dbg_cmd_ptrs(struct xhci_hcd *xhci); void xhci_dbg_ring_ptrs(struct xhci_hcd *xhci, struct xhci_ring *ring); -void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep); -void xhci_dbg_device_ctx(struct xhci_hcd *xhci, struct xhci_device_ctx *ctx, dma_addr_t dma, unsigned int last_ep); +void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx, unsigned int last_ep); /* xHCI memory managment */ void xhci_mem_cleanup(struct xhci_hcd *xhci); @@ -1207,4 +1209,9 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, u16 wIndex, char *buf, u16 wLength); int xhci_hub_status_data(struct usb_hcd *hcd, char *buf); +/* xHCI contexts */ +struct xhci_input_control_ctx *xhci_get_input_control_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx); +struct xhci_slot_ctx *xhci_get_slot_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx); +struct xhci_ep_ctx *xhci_get_ep_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx, unsigned int ep_index); + #endif /* __LINUX_XHCI_HCD_H */ -- GitLab From c92bcfa7b4038d8ffe1f02e21269f18eb0b64144 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:05:21 -0700 Subject: [PATCH 0450/1342] USB: xhci: Stall handling bug fixes. Correct the xHCI code to handle stalls on USB endpoints. We need to move the endpoint ring's dequeue pointer past the stalled transfer, or the HW will try to restart the transfer the next time the doorbell is rung. Don't attempt to clear a halt on an endpoint if we haven't seen a stalled transfer for it. The USB core will attempt to clear a halt on all endpoints when it selects a new configuration. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-hcd.c | 24 +++++++ drivers/usb/host/xhci-ring.c | 133 ++++++++++++++++++++++------------- drivers/usb/host/xhci.h | 12 ++++ 3 files changed, 120 insertions(+), 49 deletions(-) diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index 057a07e876b..816c39caca1 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -1089,6 +1089,8 @@ void xhci_endpoint_reset(struct usb_hcd *hcd, unsigned int ep_index; unsigned long flags; int ret; + struct xhci_dequeue_state deq_state; + struct xhci_ring *ep_ring; xhci = hcd_to_xhci(hcd); udev = (struct usb_device *) ep->hcpriv; @@ -1098,11 +1100,33 @@ void xhci_endpoint_reset(struct usb_hcd *hcd, if (!ep->hcpriv) return; ep_index = xhci_get_endpoint_index(&ep->desc); + ep_ring = xhci->devs[udev->slot_id]->ep_rings[ep_index]; + if (!ep_ring->stopped_td) { + xhci_dbg(xhci, "Endpoint 0x%x not halted, refusing to reset.\n", + ep->desc.bEndpointAddress); + return; + } xhci_dbg(xhci, "Queueing reset endpoint command\n"); spin_lock_irqsave(&xhci->lock, flags); ret = xhci_queue_reset_ep(xhci, udev->slot_id, ep_index); + /* + * Can't change the ring dequeue pointer until it's transitioned to the + * stopped state, which is only upon a successful reset endpoint + * command. Better hope that last command worked! + */ if (!ret) { + xhci_dbg(xhci, "Cleaning up stalled endpoint ring\n"); + /* We need to move the HW's dequeue pointer past this TD, + * or it will attempt to resend it on the next doorbell ring. + */ + xhci_find_new_dequeue_state(xhci, udev->slot_id, + ep_index, ep_ring->stopped_td, &deq_state); + xhci_dbg(xhci, "Queueing new dequeue state\n"); + xhci_queue_new_dequeue_state(xhci, ep_ring, + udev->slot_id, + ep_index, &deq_state); + kfree(ep_ring->stopped_td); xhci_ring_cmd_db(xhci); } spin_unlock_irqrestore(&xhci->lock, flags); diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index ea31753c313..aa88a067148 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -335,12 +335,6 @@ static struct xhci_segment *find_trb_seg( return cur_seg; } -struct dequeue_state { - struct xhci_segment *new_deq_seg; - union xhci_trb *new_deq_ptr; - int new_cycle_state; -}; - /* * Move the xHC's endpoint ring dequeue pointer past cur_td. * Record the new state of the xHC's endpoint ring dequeue segment, @@ -355,26 +349,30 @@ struct dequeue_state { * - Finally we move the dequeue state one TRB further, toggling the cycle bit * if we've moved it past a link TRB with the toggle cycle bit set. */ -static void find_new_dequeue_state(struct xhci_hcd *xhci, +void xhci_find_new_dequeue_state(struct xhci_hcd *xhci, unsigned int slot_id, unsigned int ep_index, - struct xhci_td *cur_td, struct dequeue_state *state) + struct xhci_td *cur_td, struct xhci_dequeue_state *state) { struct xhci_virt_device *dev = xhci->devs[slot_id]; struct xhci_ring *ep_ring = dev->ep_rings[ep_index]; struct xhci_generic_trb *trb; struct xhci_ep_ctx *ep_ctx; + dma_addr_t addr; state->new_cycle_state = 0; + xhci_dbg(xhci, "Finding segment containing stopped TRB.\n"); state->new_deq_seg = find_trb_seg(cur_td->start_seg, ep_ring->stopped_trb, &state->new_cycle_state); if (!state->new_deq_seg) BUG(); /* Dig out the cycle state saved by the xHC during the stop ep cmd */ + xhci_dbg(xhci, "Finding endpoint context\n"); ep_ctx = xhci_get_ep_ctx(xhci, dev->out_ctx, ep_index); state->new_cycle_state = 0x1 & ep_ctx->deq; state->new_deq_ptr = cur_td->last_trb; + xhci_dbg(xhci, "Finding segment containing last TRB in TD.\n"); state->new_deq_seg = find_trb_seg(state->new_deq_seg, state->new_deq_ptr, &state->new_cycle_state); @@ -388,6 +386,12 @@ static void find_new_dequeue_state(struct xhci_hcd *xhci, next_trb(xhci, ep_ring, &state->new_deq_seg, &state->new_deq_ptr); /* Don't update the ring cycle state for the producer (us). */ + xhci_dbg(xhci, "New dequeue segment = %p (virtual)\n", + state->new_deq_seg); + addr = xhci_trb_virt_to_dma(state->new_deq_seg, state->new_deq_ptr); + xhci_dbg(xhci, "New dequeue pointer = 0x%llx (DMA)\n", + (unsigned long long) addr); + xhci_dbg(xhci, "Setting dequeue pointer in internal ring state.\n"); ep_ring->dequeue = state->new_deq_ptr; ep_ring->deq_seg = state->new_deq_seg; } @@ -437,6 +441,30 @@ static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id, unsigned int ep_index, struct xhci_segment *deq_seg, union xhci_trb *deq_ptr, u32 cycle_state); +void xhci_queue_new_dequeue_state(struct xhci_hcd *xhci, + struct xhci_ring *ep_ring, unsigned int slot_id, + unsigned int ep_index, struct xhci_dequeue_state *deq_state) +{ + xhci_dbg(xhci, "Set TR Deq Ptr cmd, new deq seg = %p (0x%llx dma), " + "new deq ptr = %p (0x%llx dma), new cycle = %u\n", + deq_state->new_deq_seg, + (unsigned long long)deq_state->new_deq_seg->dma, + deq_state->new_deq_ptr, + (unsigned long long)xhci_trb_virt_to_dma(deq_state->new_deq_seg, deq_state->new_deq_ptr), + deq_state->new_cycle_state); + queue_set_tr_deq(xhci, slot_id, ep_index, + deq_state->new_deq_seg, + deq_state->new_deq_ptr, + (u32) deq_state->new_cycle_state); + /* Stop the TD queueing code from ringing the doorbell until + * this command completes. The HC won't set the dequeue pointer + * if the ring is running, and ringing the doorbell starts the + * ring running. + */ + ep_ring->state |= SET_DEQ_PENDING; + xhci_ring_cmd_db(xhci); +} + /* * When we get a command completion for a Stop Endpoint Command, we need to * unlink any cancelled TDs from the ring. There are two ways to do that: @@ -457,7 +485,7 @@ static void handle_stopped_endpoint(struct xhci_hcd *xhci, struct xhci_td *cur_td = 0; struct xhci_td *last_unlinked_td; - struct dequeue_state deq_state; + struct xhci_dequeue_state deq_state; #ifdef CONFIG_USB_HCD_STAT ktime_t stop_time = ktime_get(); #endif @@ -485,7 +513,7 @@ static void handle_stopped_endpoint(struct xhci_hcd *xhci, * move the xHC endpoint ring dequeue pointer past this TD. */ if (cur_td == ep_ring->stopped_td) - find_new_dequeue_state(xhci, slot_id, ep_index, cur_td, + xhci_find_new_dequeue_state(xhci, slot_id, ep_index, cur_td, &deq_state); else td_to_noop(xhci, ep_ring, cur_td); @@ -501,24 +529,8 @@ static void handle_stopped_endpoint(struct xhci_hcd *xhci, /* If necessary, queue a Set Transfer Ring Dequeue Pointer command */ if (deq_state.new_deq_ptr && deq_state.new_deq_seg) { - xhci_dbg(xhci, "Set TR Deq Ptr cmd, new deq seg = %p (0x%llx dma), " - "new deq ptr = %p (0x%llx dma), new cycle = %u\n", - deq_state.new_deq_seg, - (unsigned long long)deq_state.new_deq_seg->dma, - deq_state.new_deq_ptr, - (unsigned long long)xhci_trb_virt_to_dma(deq_state.new_deq_seg, deq_state.new_deq_ptr), - deq_state.new_cycle_state); - queue_set_tr_deq(xhci, slot_id, ep_index, - deq_state.new_deq_seg, - deq_state.new_deq_ptr, - (u32) deq_state.new_cycle_state); - /* Stop the TD queueing code from ringing the doorbell until - * this command completes. The HC won't set the dequeue pointer - * if the ring is running, and ringing the doorbell starts the - * ring running. - */ - ep_ring->state |= SET_DEQ_PENDING; - xhci_ring_cmd_db(xhci); + xhci_queue_new_dequeue_state(xhci, ep_ring, + slot_id, ep_index, &deq_state); } else { /* Otherwise just ring the doorbell to restart the ring */ ring_ep_doorbell(xhci, slot_id, ep_index); @@ -929,12 +941,15 @@ static int handle_tx_event(struct xhci_hcd *xhci, if (event_trb != ep_ring->dequeue) { /* The event was for the status stage */ if (event_trb == td->last_trb) { - /* Did we already see a short data stage? */ - if (td->urb->actual_length != 0) - status = -EREMOTEIO; - else + if (td->urb->actual_length != 0) { + /* Don't overwrite a previously set error code */ + if (status == -EINPROGRESS || status == 0) + /* Did we already see a short data stage? */ + status = -EREMOTEIO; + } else { td->urb->actual_length = td->urb->transfer_buffer_length; + } } else { /* Maybe the event was for the data stage? */ if (GET_COMP_CODE(event->transfer_len) != COMP_STOP_INVAL) { @@ -992,16 +1007,20 @@ static int handle_tx_event(struct xhci_hcd *xhci, TRB_LEN(event->transfer_len)); td->urb->actual_length = 0; } - if (td->urb->transfer_flags & URB_SHORT_NOT_OK) - status = -EREMOTEIO; - else - status = 0; + /* Don't overwrite a previously set error code */ + if (status == -EINPROGRESS) { + if (td->urb->transfer_flags & URB_SHORT_NOT_OK) + status = -EREMOTEIO; + else + status = 0; + } } else { td->urb->actual_length = td->urb->transfer_buffer_length; /* Ignore a short packet completion if the * untransferred length was zero. */ - status = 0; + if (status == -EREMOTEIO) + status = 0; } } else { /* Slow path - walk the list, starting from the dequeue @@ -1028,19 +1047,30 @@ static int handle_tx_event(struct xhci_hcd *xhci, TRB_LEN(event->transfer_len); } } - /* The Endpoint Stop Command completion will take care of - * any stopped TDs. A stopped TD may be restarted, so don't update the - * ring dequeue pointer or take this TD off any lists yet. - */ if (GET_COMP_CODE(event->transfer_len) == COMP_STOP_INVAL || GET_COMP_CODE(event->transfer_len) == COMP_STOP) { + /* The Endpoint Stop Command completion will take care of any + * stopped TDs. A stopped TD may be restarted, so don't update + * the ring dequeue pointer or take this TD off any lists yet. + */ ep_ring->stopped_td = td; ep_ring->stopped_trb = event_trb; } else { - /* Update ring dequeue pointer */ - while (ep_ring->dequeue != td->last_trb) + if (GET_COMP_CODE(event->transfer_len) == COMP_STALL) { + /* The transfer is completed from the driver's + * perspective, but we need to issue a set dequeue + * command for this stalled endpoint to move the dequeue + * pointer past the TD. We can't do that here because + * the halt condition must be cleared first. + */ + ep_ring->stopped_td = td; + ep_ring->stopped_trb = event_trb; + } else { + /* Update ring dequeue pointer */ + while (ep_ring->dequeue != td->last_trb) + inc_deq(xhci, ep_ring, false); inc_deq(xhci, ep_ring, false); - inc_deq(xhci, ep_ring, false); + } /* Clean up the endpoint's TD list */ urb = td->urb; @@ -1050,7 +1080,10 @@ static int handle_tx_event(struct xhci_hcd *xhci, list_del(&td->cancelled_td_list); ep_ring->cancels_pending--; } - kfree(td); + /* Leave the TD around for the reset endpoint function to use */ + if (GET_COMP_CODE(event->transfer_len) != COMP_STALL) { + kfree(td); + } urb->hcpriv = NULL; } cleanup: @@ -1166,13 +1199,13 @@ static int prepare_ring(struct xhci_hcd *xhci, struct xhci_ring *ep_ring, */ xhci_warn(xhci, "WARN urb submitted to disabled ep\n"); return -ENOENT; - case EP_STATE_HALTED: case EP_STATE_ERROR: - xhci_warn(xhci, "WARN waiting for halt or error on ep " - "to be cleared\n"); + xhci_warn(xhci, "WARN waiting for error on ep to be cleared\n"); /* FIXME event handling code for error needs to clear it */ /* XXX not sure if this should be -ENOENT or not */ return -EINVAL; + case EP_STATE_HALTED: + xhci_dbg(xhci, "WARN halted endpoint, queueing URB anyway.\n"); case EP_STATE_STOPPED: case EP_STATE_RUNNING: break; @@ -1724,10 +1757,12 @@ static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id, u32 type = TRB_TYPE(TRB_SET_DEQ); addr = xhci_trb_virt_to_dma(deq_seg, deq_ptr); - if (addr == 0) + if (addr == 0) { xhci_warn(xhci, "WARN Cannot submit Set TR Deq Ptr\n"); xhci_warn(xhci, "WARN deq seg = %p, deq pt = %p\n", deq_seg, deq_ptr); + return 0; + } return queue_command(xhci, lower_32_bits(addr) | cycle_state, upper_32_bits(addr), 0, trb_slot_id | trb_ep_index | type); diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 9c108c63270..d31d32206ba 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -952,6 +952,12 @@ struct xhci_ring { u32 cycle_state; }; +struct xhci_dequeue_state { + struct xhci_segment *new_deq_seg; + union xhci_trb *new_deq_ptr; + int new_cycle_state; +}; + struct xhci_erst_entry { /* 64-bit event ring segment address */ u64 seg_addr; @@ -1203,6 +1209,12 @@ int xhci_queue_configure_endpoint(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr, u32 slot_id); int xhci_queue_reset_ep(struct xhci_hcd *xhci, int slot_id, unsigned int ep_index); +void xhci_find_new_dequeue_state(struct xhci_hcd *xhci, + unsigned int slot_id, unsigned int ep_index, + struct xhci_td *cur_td, struct xhci_dequeue_state *state); +void xhci_queue_new_dequeue_state(struct xhci_hcd *xhci, + struct xhci_ring *ep_ring, unsigned int slot_id, + unsigned int ep_index, struct xhci_dequeue_state *deq_state); /* xHCI roothub code */ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, u16 wIndex, -- GitLab From 044dcc824a167e3d39ba69a49e2b723dd10678f6 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Sun, 26 Jul 2009 18:27:29 +0200 Subject: [PATCH 0451/1342] pata_pcmcia: add CNF-CDROM-ID Fixes this report: http://article.gmane.org/gmane.linux.kernel.pcmcia.devel/2228/ Reported-by: John McGrath Signed-off-by: Wolfram Sang Signed-off-by: Jeff Garzik --- drivers/ata/pata_pcmcia.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/ata/pata_pcmcia.c b/drivers/ata/pata_pcmcia.c index f4d009ed50a..dc99e26f8e5 100644 --- a/drivers/ata/pata_pcmcia.c +++ b/drivers/ata/pata_pcmcia.c @@ -411,6 +411,7 @@ static struct pcmcia_device_id pcmcia_devices[] = { PCMCIA_DEVICE_PROD_ID123("PCMCIA", "IDE CARD", "F1", 0x281f1c5d, 0x1907960c, 0xf7fde8b9), PCMCIA_DEVICE_PROD_ID12("ARGOSY", "CD-ROM", 0x78f308dc, 0x66536591), PCMCIA_DEVICE_PROD_ID12("ARGOSY", "PnPIDE", 0x78f308dc, 0x0c694728), + PCMCIA_DEVICE_PROD_ID12("CNF ", "CD-ROM", 0x46d7db81, 0x66536591), PCMCIA_DEVICE_PROD_ID12("CNF CD-M", "CD-ROM", 0x7d93b852, 0x66536591), PCMCIA_DEVICE_PROD_ID12("Creative Technology Ltd.", "PCMCIA CD-ROM Interface Card", 0xff8c8a45, 0xfe8020c4), PCMCIA_DEVICE_PROD_ID12("Digital Equipment Corporation.", "Digital Mobile Media CD-ROM", 0x17692a66, 0xef1dcbde), -- GitLab From 705d201414382b0966d7c903d738dfdb9380e4af Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Sun, 26 Jul 2009 16:21:01 +0200 Subject: [PATCH 0452/1342] libata: add missing NULL pointer check to ata_eh_reset() drivers/ata/libata-eh.c +2403 ata_eh_reset(80) warning: variable derefenced before check 'slave' Please note that this is _not_ a real bug at the moment since ata_eh_context structure is embedded into ata_list structure and the code alwas checks for 'slave' before accessing 'sehc'. Anyway lets add missing check and always have a valid 'sehc' pointer (which makes code easier to understand and prevents introducing some possible bugs in the future). Reported-by: Dan Carpenter Cc: corbet@lwn.net Cc: eteo@redhat.com Signed-off-by: Bartlomiej Zolnierkiewicz Signed-off-by: Jeff Garzik --- drivers/ata/libata-eh.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c index 1a07c061f64..79711b64054 100644 --- a/drivers/ata/libata-eh.c +++ b/drivers/ata/libata-eh.c @@ -2327,7 +2327,7 @@ int ata_eh_reset(struct ata_link *link, int classify, struct ata_port *ap = link->ap; struct ata_link *slave = ap->slave_link; struct ata_eh_context *ehc = &link->eh_context; - struct ata_eh_context *sehc = &slave->eh_context; + struct ata_eh_context *sehc = slave ? &slave->eh_context : NULL; unsigned int *classes = ehc->classes; unsigned int lflags = link->flags; int verbose = !(ehc->i.flags & ATA_EHI_QUIET); -- GitLab From c9abde12d6debe5b97f36fb43cf188c1b9cd477f Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Sun, 26 Jul 2009 16:05:13 +0200 Subject: [PATCH 0453/1342] libata: remove superfluous NULL pointer checks host->ports[] always contain pointers to valid port structures since a "dummy port" structure is used in case if there is no physical port. This patch takes care of two entries from Dan's list: drivers/ata/sata_sil.c +535 sil_interrupt(13) warning: variable derefenced before check 'ap' drivers/ata/sata_mv.c +2517 mv_unexpected_intr(6) warning: variable derefenced before check 'ap' and of another needless NULL pointer check in pata_octeon_cf.c. Reported-by: Dan Carpenter Cc: corbet@lwn.net Cc: eteo@redhat.com Signed-off-by: Bartlomiej Zolnierkiewicz Signed-off-by: Jeff Garzik --- drivers/ata/pata_octeon_cf.c | 3 ++- drivers/ata/sata_mv.c | 2 +- drivers/ata/sata_sil.c | 2 +- 3 files changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/ata/pata_octeon_cf.c b/drivers/ata/pata_octeon_cf.c index 8d9343accf3..abdd19fe990 100644 --- a/drivers/ata/pata_octeon_cf.c +++ b/drivers/ata/pata_octeon_cf.c @@ -653,7 +653,8 @@ static irqreturn_t octeon_cf_interrupt(int irq, void *dev_instance) ap = host->ports[i]; ocd = ap->dev->platform_data; - if (!ap || (ap->flags & ATA_FLAG_DISABLED)) + + if (ap->flags & ATA_FLAG_DISABLED) continue; ocd = ap->dev->platform_data; diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index 23714aefb82..c19417e0220 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -2514,7 +2514,7 @@ static void mv_unexpected_intr(struct ata_port *ap, int edma_was_enabled) char *when = "idle"; ata_ehi_clear_desc(ehi); - if (!ap || (ap->flags & ATA_FLAG_DISABLED)) { + if (ap->flags & ATA_FLAG_DISABLED) { when = "disabled"; } else if (edma_was_enabled) { when = "EDMA enabled"; diff --git a/drivers/ata/sata_sil.c b/drivers/ata/sata_sil.c index 030ec079b18..35bd5cc7f28 100644 --- a/drivers/ata/sata_sil.c +++ b/drivers/ata/sata_sil.c @@ -532,7 +532,7 @@ static irqreturn_t sil_interrupt(int irq, void *dev_instance) struct ata_port *ap = host->ports[i]; u32 bmdma2 = readl(mmio_base + sil_port[ap->port_no].bmdma2); - if (unlikely(!ap || ap->flags & ATA_FLAG_DISABLED)) + if (unlikely(ap->flags & ATA_FLAG_DISABLED)) continue; /* turn off SATA_IRQ if not supported */ -- GitLab From c1f57d9b9846e7366c328f916d1a82d03ba4312c Mon Sep 17 00:00:00 2001 From: David Milburn Date: Wed, 22 Jul 2009 15:15:56 -0500 Subject: [PATCH 0454/1342] ahci: add device IDs for Ibex Peak ahci controllers Add device IDS for Ibex Peak SATA AHCI Controllers Signed-off-by: Jaroslav Kysela Signed-off-by: David Milburn Signed-off-by: Jeff Garzik --- drivers/ata/ahci.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c index 336eb1ed73c..958c1fa4190 100644 --- a/drivers/ata/ahci.c +++ b/drivers/ata/ahci.c @@ -515,10 +515,14 @@ static const struct pci_device_id ahci_pci_tbl[] = { { PCI_VDEVICE(INTEL, 0x3a05), board_ahci }, /* ICH10 */ { PCI_VDEVICE(INTEL, 0x3a22), board_ahci }, /* ICH10 */ { PCI_VDEVICE(INTEL, 0x3a25), board_ahci }, /* ICH10 */ + { PCI_VDEVICE(INTEL, 0x3b22), board_ahci }, /* PCH AHCI */ + { PCI_VDEVICE(INTEL, 0x3b23), board_ahci }, /* PCH AHCI */ { PCI_VDEVICE(INTEL, 0x3b24), board_ahci }, /* PCH RAID */ { PCI_VDEVICE(INTEL, 0x3b25), board_ahci }, /* PCH RAID */ + { PCI_VDEVICE(INTEL, 0x3b29), board_ahci }, /* PCH AHCI */ { PCI_VDEVICE(INTEL, 0x3b2b), board_ahci }, /* PCH RAID */ { PCI_VDEVICE(INTEL, 0x3b2c), board_ahci }, /* PCH RAID */ + { PCI_VDEVICE(INTEL, 0x3b2f), board_ahci }, /* PCH AHCI */ /* JMicron 360/1/3/5/6, match class to avoid IDE function */ { PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, -- GitLab From 6034734d333c1bd01119a5b480b34a507a3adf56 Mon Sep 17 00:00:00 2001 From: Steve Conklin Date: Thu, 16 Jul 2009 16:27:56 -0500 Subject: [PATCH 0455/1342] ata_piix: Add new laptop short cable IDs OriginalAuthor: Michael Frey Signed-off-by: Steve Conklin Signed-off-by: Jeff Garzik --- drivers/ata/ata_piix.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c index d0a14cf2bd7..deada1fe6a0 100644 --- a/drivers/ata/ata_piix.c +++ b/drivers/ata/ata_piix.c @@ -596,9 +596,11 @@ static const struct ich_laptop ich_laptop[] = { { 0x27DF, 0x0005, 0x0280 }, /* ICH7 on Acer 5602WLMi */ { 0x27DF, 0x1025, 0x0102 }, /* ICH7 on Acer 5602aWLMi */ { 0x27DF, 0x1025, 0x0110 }, /* ICH7 on Acer 3682WLMi */ + { 0x27DF, 0x1028, 0x02b0 }, /* ICH7 on unknown Dell */ { 0x27DF, 0x1043, 0x1267 }, /* ICH7 on Asus W5F */ { 0x27DF, 0x103C, 0x30A1 }, /* ICH7 on HP Compaq nc2400 */ { 0x27DF, 0x1071, 0xD221 }, /* ICH7 on Hercules EC-900 */ + { 0x27DF, 0x152D, 0x0778 }, /* ICH7 on unknown Intel */ { 0x24CA, 0x1025, 0x0061 }, /* ICH4 on ACER Aspire 2023WLMi */ { 0x24CA, 0x1025, 0x003d }, /* ICH4 on ACER TM290 */ { 0x266F, 0x1025, 0x0066 }, /* ICH6 on ACER Aspire 1694WLMi */ -- GitLab From 760cdb7760be928e85a021552253eb1b39acdf37 Mon Sep 17 00:00:00 2001 From: Steve Conklin Date: Thu, 16 Jul 2009 16:31:10 -0500 Subject: [PATCH 0456/1342] ata_piix: Add new short cable ID OriginalAuthor: Tony Espy Signed-off-by: Steve Conklin Signed-off-by: Jeff Garzik --- drivers/ata/ata_piix.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c index deada1fe6a0..56b8a3ff128 100644 --- a/drivers/ata/ata_piix.c +++ b/drivers/ata/ata_piix.c @@ -599,6 +599,7 @@ static const struct ich_laptop ich_laptop[] = { { 0x27DF, 0x1028, 0x02b0 }, /* ICH7 on unknown Dell */ { 0x27DF, 0x1043, 0x1267 }, /* ICH7 on Asus W5F */ { 0x27DF, 0x103C, 0x30A1 }, /* ICH7 on HP Compaq nc2400 */ + { 0x27DF, 0x103C, 0x361a }, /* ICH7 on unkown HP */ { 0x27DF, 0x1071, 0xD221 }, /* ICH7 on Hercules EC-900 */ { 0x27DF, 0x152D, 0x0778 }, /* ICH7 on unknown Intel */ { 0x24CA, 0x1025, 0x0061 }, /* ICH4 on ACER Aspire 2023WLMi */ -- GitLab From 7d084d96fdf1d791cb171da57efc1ca89d68dd6c Mon Sep 17 00:00:00 2001 From: Sergey Matyukevich Date: Thu, 16 Jul 2009 22:38:55 +0400 Subject: [PATCH 0457/1342] libata: Updates and fixes for pata_at91 driver Please consider the following updates and fixes for pata_at91 driver. * Removed extra headers Here we need only static memory controller properties, which are contained in generic header at91sam9_smc.h. No need to include any specific headers for at91sam9260 SoC. * No harsh BUG_ON for get_clk in set_smc_timing function get_clk is now performed in driver probing function, probing fails if master clock is not available * Fixed uint/ulong mess in calc_mck_cycles function Signed-off-by: Sergey Matyukevich Signed-off-by: Jeff Garzik --- drivers/ata/pata_at91.c | 67 ++++++++++++++++++++++------------------- 1 file changed, 36 insertions(+), 31 deletions(-) diff --git a/drivers/ata/pata_at91.c b/drivers/ata/pata_at91.c index 8561a9f195c..5702affcb32 100644 --- a/drivers/ata/pata_at91.c +++ b/drivers/ata/pata_at91.c @@ -26,9 +26,7 @@ #include #include -#include #include -#include #include #include @@ -44,65 +42,62 @@ struct at91_ide_info { unsigned long mode; unsigned int cs; + struct clk *mck; + void __iomem *ide_addr; void __iomem *alt_addr; }; -const struct ata_timing initial_timing = +static const struct ata_timing initial_timing = {XFER_PIO_0, 70, 290, 240, 600, 165, 150, 600, 0}; -static unsigned int calc_mck_cycles(unsigned int ns, unsigned int mck_hz) +static unsigned long calc_mck_cycles(unsigned long ns, unsigned long mck_hz) { unsigned long mul; - /* - * cycles = x [nsec] * f [Hz] / 10^9 [ns in sec] = - * x * (f / 1_000_000_000) = - * x * ((f * 65536) / 1_000_000_000) / 65536 = - * x * (((f / 10_000) * 65536) / 100_000) / 65536 = - */ + /* + * cycles = x [nsec] * f [Hz] / 10^9 [ns in sec] = + * x * (f / 1_000_000_000) = + * x * ((f * 65536) / 1_000_000_000) / 65536 = + * x * (((f / 10_000) * 65536) / 100_000) / 65536 = + */ - mul = (mck_hz / 10000) << 16; - mul /= 100000; + mul = (mck_hz / 10000) << 16; + mul /= 100000; - return (ns * mul + 65536) >> 16; /* rounding */ + return (ns * mul + 65536) >> 16; /* rounding */ } static void set_smc_mode(struct at91_ide_info *info) { - at91_sys_write(AT91_SMC_MODE(info->cs), info->mode); - return; + at91_sys_write(AT91_SMC_MODE(info->cs), info->mode); + return; } static void set_smc_timing(struct device *dev, struct at91_ide_info *info, const struct ata_timing *ata) { - int read_cycle, write_cycle, active, recover; - int nrd_setup, nrd_pulse, nrd_recover; - int nwe_setup, nwe_pulse; + unsigned long read_cycle, write_cycle, active, recover; + unsigned long nrd_setup, nrd_pulse, nrd_recover; + unsigned long nwe_setup, nwe_pulse; - int ncs_write_setup, ncs_write_pulse; - int ncs_read_setup, ncs_read_pulse; + unsigned long ncs_write_setup, ncs_write_pulse; + unsigned long ncs_read_setup, ncs_read_pulse; - unsigned int mck_hz; - struct clk *mck; + unsigned long mck_hz; read_cycle = ata->cyc8b; nrd_setup = ata->setup; nrd_pulse = ata->act8b; nrd_recover = ata->rec8b; - mck = clk_get(NULL, "mck"); - BUG_ON(IS_ERR(mck)); - mck_hz = clk_get_rate(mck); + mck_hz = clk_get_rate(info->mck); read_cycle = calc_mck_cycles(read_cycle, mck_hz); nrd_setup = calc_mck_cycles(nrd_setup, mck_hz); nrd_pulse = calc_mck_cycles(nrd_pulse, mck_hz); nrd_recover = calc_mck_cycles(nrd_recover, mck_hz); - clk_put(mck); - active = nrd_setup + nrd_pulse; recover = read_cycle - active; @@ -121,13 +116,13 @@ static void set_smc_timing(struct device *dev, ncs_write_setup = ncs_read_setup; ncs_write_pulse = ncs_read_pulse; - dev_dbg(dev, "ATA timings: nrd_setup = %d nrd_pulse = %d nrd_cycle = %d\n", + dev_dbg(dev, "ATA timings: nrd_setup = %lu nrd_pulse = %lu nrd_cycle = %lu\n", nrd_setup, nrd_pulse, read_cycle); - dev_dbg(dev, "ATA timings: nwe_setup = %d nwe_pulse = %d nwe_cycle = %d\n", + dev_dbg(dev, "ATA timings: nwe_setup = %lu nwe_pulse = %lu nwe_cycle = %lu\n", nwe_setup, nwe_pulse, write_cycle); - dev_dbg(dev, "ATA timings: ncs_read_setup = %d ncs_read_pulse = %d\n", + dev_dbg(dev, "ATA timings: ncs_read_setup = %lu ncs_read_pulse = %lu\n", ncs_read_setup, ncs_read_pulse); - dev_dbg(dev, "ATA timings: ncs_write_setup = %d ncs_write_pulse = %d\n", + dev_dbg(dev, "ATA timings: ncs_write_setup = %lu ncs_write_pulse = %lu\n", ncs_write_setup, ncs_write_pulse); at91_sys_write(AT91_SMC_SETUP(info->cs), @@ -217,6 +212,7 @@ static int __devinit pata_at91_probe(struct platform_device *pdev) struct resource *mem_res; struct ata_host *host; struct ata_port *ap; + int irq_flags = 0; int irq = 0; int ret; @@ -261,6 +257,13 @@ static int __devinit pata_at91_probe(struct platform_device *pdev) return -ENOMEM; } + info->mck = clk_get(NULL, "mck"); + + if (IS_ERR(info->mck)) { + dev_err(dev, "failed to get access to mck clock\n"); + return -ENODEV; + } + info->cs = board->chipselect; info->mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_READY | AT91_SMC_BAT_SELECT | @@ -304,6 +307,7 @@ err_alt_ioremap: devm_iounmap(dev, info->ide_addr); err_ide_ioremap: + clk_put(info->mck); kfree(info); return ret; @@ -326,6 +330,7 @@ static int __devexit pata_at91_remove(struct platform_device *pdev) devm_iounmap(dev, info->ide_addr); devm_iounmap(dev, info->alt_addr); + clk_put(info->mck); kfree(info); return 0; -- GitLab From 5920dadfb4aec6c1372c5570e71bcd3b4837e63c Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Wed, 15 Jul 2009 17:11:41 +0900 Subject: [PATCH 0458/1342] libata: accept late unlocking of HPA On certain configurations, HPA isn't or can't be unlocked during probing but it somehow ends up unlocked afterwards. In the following thread, the problem can be reliably reproduced after resuming from STR. The BIOS turns on HPA during boot but forgets to do it during resume. http://thread.gmane.org/gmane.linux.kernel/858310 This patch updates libata revalidation such that it considers native n_sectors. If the device size has increased to match native n_sectors, it's assumed that HPA has been unlocked involuntarily and the device is recognized as the same one. This should be fairly safe while nicely working around the problem. Signed-off-by: Tejun Heo Reported-by: Christof Warlich Signed-off-by: Jeff Garzik --- drivers/ata/libata-core.c | 30 +++++++++++++++++++++++------- include/linux/libata.h | 1 + 2 files changed, 24 insertions(+), 7 deletions(-) diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index 2c6aedaef71..8ac98ff16d7 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -1515,6 +1515,7 @@ static int ata_hpa_resize(struct ata_device *dev) return rc; } + dev->n_native_sectors = native_sectors; /* nothing to do? */ if (native_sectors <= sectors || !ata_ignore_hpa) { @@ -4099,6 +4100,7 @@ int ata_dev_revalidate(struct ata_device *dev, unsigned int new_class, unsigned int readid_flags) { u64 n_sectors = dev->n_sectors; + u64 n_native_sectors = dev->n_native_sectors; int rc; if (!ata_dev_enabled(dev)) @@ -4128,16 +4130,30 @@ int ata_dev_revalidate(struct ata_device *dev, unsigned int new_class, /* verify n_sectors hasn't changed */ if (dev->class == ATA_DEV_ATA && n_sectors && dev->n_sectors != n_sectors) { - ata_dev_printk(dev, KERN_INFO, "n_sectors mismatch " + ata_dev_printk(dev, KERN_WARNING, "n_sectors mismatch " "%llu != %llu\n", (unsigned long long)n_sectors, (unsigned long long)dev->n_sectors); - - /* restore original n_sectors */ - dev->n_sectors = n_sectors; - - rc = -ENODEV; - goto fail; + /* + * Something could have caused HPA to be unlocked + * involuntarily. If n_native_sectors hasn't changed + * and the new size matches it, keep the device. + */ + if (dev->n_native_sectors == n_native_sectors && + dev->n_sectors > n_sectors && + dev->n_sectors == n_native_sectors) { + ata_dev_printk(dev, KERN_WARNING, + "new n_sectors matches native, probably " + "late HPA unlock, continuing\n"); + /* keep using the old n_sectors */ + dev->n_sectors = n_sectors; + } else { + /* restore original n_[native]_sectors and fail */ + dev->n_native_sectors = n_native_sectors; + dev->n_sectors = n_sectors; + rc = -ENODEV; + goto fail; + } } return 0; diff --git a/include/linux/libata.h b/include/linux/libata.h index 79b6d7fd4ac..e5b6e33c657 100644 --- a/include/linux/libata.h +++ b/include/linux/libata.h @@ -589,6 +589,7 @@ struct ata_device { #endif /* n_sector is CLEAR_BEGIN, read comment above CLEAR_BEGIN */ u64 n_sectors; /* size of device, if ATA */ + u64 n_native_sectors; /* native size, if ATA */ unsigned int class; /* ATA_DEV_xxx */ unsigned long unpark_deadline; -- GitLab From 68dbcb726e372b3c8ef60b79b5aff4174dd2bdf0 Mon Sep 17 00:00:00 2001 From: Jeff Garzik Date: Tue, 28 Jul 2009 22:36:59 -0400 Subject: [PATCH 0459/1342] Remove zero-length file drivers/char/vr41xx_giu.c Signed-off-by: Jeff Garzik --- drivers/char/vr41xx_giu.c | 0 1 file changed, 0 insertions(+), 0 deletions(-) delete mode 100644 drivers/char/vr41xx_giu.c diff --git a/drivers/char/vr41xx_giu.c b/drivers/char/vr41xx_giu.c deleted file mode 100644 index e69de29bb2d..00000000000 -- GitLab From e024e11070a0a0dc7163ce1ec2da354a638bdbed Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Wed, 24 Jun 2009 09:48:08 +1000 Subject: [PATCH 0460/1342] drm/radeon/kms: add initial colortiling support. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This adds new set/get tiling interfaces where the pitch and macro/micro tiling enables can be set. Along with a flag to decide if this object should have a surface when mapped. The only thing we need to allocate with a mapped surface should be the frontbuffer. Note rotate scanout shouldn't require one, and back/depth shouldn't either, though mesa needs some fixes. It fixes the TTM interfaces along Thomas's suggestions, and I've tested the surface stealing code with two X servers and not seen any lockdep issues. I've stopped tiling the fbcon frontbuffer, as I don't see there being any advantage other than testing, I've left the testing commands in there, just flip the fb_tiled to true in radeon_fb.c Open: Can we integrate endian swapping in with this? Future features: texture tiling - need to relocate texture registers TXOFFSET* with tiling info. This also merges Michel's cleanup surfaces regs at init time patch even though it makes sense on its own, this patch really relies on it. Some PowerMac firmwares set up a tiling surface at the beginning of VRAM which messes us up otherwise. that patch is: Signed-off-by: Michel Dänzer Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/atombios_crtc.c | 11 +- drivers/gpu/drm/radeon/r100.c | 79 +++++++++++- drivers/gpu/drm/radeon/r300.c | 51 +++++++- drivers/gpu/drm/radeon/r300_reg.h | 4 +- drivers/gpu/drm/radeon/radeon.h | 32 ++++- drivers/gpu/drm/radeon/radeon_asic.h | 19 +++ drivers/gpu/drm/radeon/radeon_device.c | 2 + drivers/gpu/drm/radeon/radeon_fb.c | 12 +- drivers/gpu/drm/radeon/radeon_gem.c | 41 ++++++ drivers/gpu/drm/radeon/radeon_kms.c | 2 + drivers/gpu/drm/radeon/radeon_legacy_crtc.c | 15 ++- drivers/gpu/drm/radeon/radeon_object.c | 130 ++++++++++++++++++++ drivers/gpu/drm/radeon/radeon_ttm.c | 2 + drivers/gpu/drm/ttm/ttm_bo.c | 5 +- drivers/gpu/drm/ttm/ttm_bo_vm.c | 3 + include/drm/radeon_drm.h | 23 +++- include/drm/ttm/ttm_bo_driver.h | 15 +++ 17 files changed, 427 insertions(+), 19 deletions(-) diff --git a/drivers/gpu/drm/radeon/atombios_crtc.c b/drivers/gpu/drm/radeon/atombios_crtc.c index e64a199b5ee..eac26cdb5da 100644 --- a/drivers/gpu/drm/radeon/atombios_crtc.c +++ b/drivers/gpu/drm/radeon/atombios_crtc.c @@ -327,7 +327,7 @@ int atombios_crtc_set_base(struct drm_crtc *crtc, int x, int y, struct drm_gem_object *obj; struct drm_radeon_gem_object *obj_priv; uint64_t fb_location; - uint32_t fb_format, fb_pitch_pixels; + uint32_t fb_format, fb_pitch_pixels, tiling_flags; if (!crtc->fb) return -EINVAL; @@ -364,7 +364,14 @@ int atombios_crtc_set_base(struct drm_crtc *crtc, int x, int y, return -EINVAL; } - /* TODO tiling */ + radeon_object_get_tiling_flags(obj->driver_private, + &tiling_flags, NULL); + if (tiling_flags & RADEON_TILING_MACRO) + fb_format |= AVIVO_D1GRPH_MACRO_ADDRESS_MODE; + + if (tiling_flags & RADEON_TILING_MICRO) + fb_format |= AVIVO_D1GRPH_TILED; + if (radeon_crtc->crtc_id == 0) WREG32(AVIVO_D1VGA_CONTROL, 0); else diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index 0d05909f03f..69bd7cb5997 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -909,6 +909,7 @@ static int r100_packet0_check(struct radeon_cs_parser *p, unsigned idx; bool onereg; int r; + u32 tile_flags = 0; ib = p->ib->ptr; ib_chunk = &p->chunks[p->chunk_ib_idx]; @@ -942,7 +943,20 @@ static int r100_packet0_check(struct radeon_cs_parser *p, } tmp = ib_chunk->kdata[idx] & 0x003fffff; tmp += (((u32)reloc->lobj.gpu_offset) >> 10); - ib[idx] = (ib_chunk->kdata[idx] & 0xffc00000) | tmp; + + if (reloc->lobj.tiling_flags & RADEON_TILING_MACRO) + tile_flags |= RADEON_DST_TILE_MACRO; + if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO) { + if (reg == RADEON_SRC_PITCH_OFFSET) { + DRM_ERROR("Cannot src blit from microtiled surface\n"); + r100_cs_dump_packet(p, pkt); + return -EINVAL; + } + tile_flags |= RADEON_DST_TILE_MICRO; + } + + tmp |= tile_flags; + ib[idx] = (ib_chunk->kdata[idx] & 0x3fc00000) | tmp; break; case RADEON_RB3D_DEPTHOFFSET: case RADEON_RB3D_COLOROFFSET: @@ -987,6 +1001,25 @@ static int r100_packet0_check(struct radeon_cs_parser *p, } ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset); break; + case R300_RB3D_COLORPITCH0: + case RADEON_RB3D_COLORPITCH: + r = r100_cs_packet_next_reloc(p, &reloc); + if (r) { + DRM_ERROR("No reloc for ib[%d]=0x%04X\n", + idx, reg); + r100_cs_dump_packet(p, pkt); + return r; + } + + if (reloc->lobj.tiling_flags & RADEON_TILING_MACRO) + tile_flags |= RADEON_COLOR_TILE_ENABLE; + if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO) + tile_flags |= RADEON_COLOR_MICROTILE_ENABLE; + + tmp = ib_chunk->kdata[idx] & ~(0x7 << 16); + tmp |= tile_flags; + ib[idx] = tmp; + break; default: /* FIXME: we don't want to allow anyothers packet */ break; @@ -1707,3 +1740,47 @@ int r100_debugfs_mc_info_init(struct radeon_device *rdev) return 0; #endif } + +int r100_set_surface_reg(struct radeon_device *rdev, int reg, + uint32_t tiling_flags, uint32_t pitch, + uint32_t offset, uint32_t obj_size) +{ + int surf_index = reg * 16; + int flags = 0; + + /* r100/r200 divide by 16 */ + if (rdev->family < CHIP_R300) + flags = pitch / 16; + else + flags = pitch / 8; + + if (rdev->family <= CHIP_RS200) { + if ((tiling_flags & (RADEON_TILING_MACRO|RADEON_TILING_MICRO)) + == (RADEON_TILING_MACRO|RADEON_TILING_MICRO)) + flags |= RADEON_SURF_TILE_COLOR_BOTH; + if (tiling_flags & RADEON_TILING_MACRO) + flags |= RADEON_SURF_TILE_COLOR_MACRO; + } else if (rdev->family <= CHIP_RV280) { + if (tiling_flags & (RADEON_TILING_MACRO)) + flags |= R200_SURF_TILE_COLOR_MACRO; + if (tiling_flags & RADEON_TILING_MICRO) + flags |= R200_SURF_TILE_COLOR_MICRO; + } else { + if (tiling_flags & RADEON_TILING_MACRO) + flags |= R300_SURF_TILE_MACRO; + if (tiling_flags & RADEON_TILING_MICRO) + flags |= R300_SURF_TILE_MICRO; + } + + DRM_DEBUG("writing surface %d %d %x %x\n", reg, flags, offset, offset+obj_size-1); + WREG32(RADEON_SURFACE0_INFO + surf_index, flags); + WREG32(RADEON_SURFACE0_LOWER_BOUND + surf_index, offset); + WREG32(RADEON_SURFACE0_UPPER_BOUND + surf_index, offset + obj_size - 1); + return 0; +} + +void r100_clear_surface_reg(struct radeon_device *rdev, int reg) +{ + int surf_index = reg * 16; + WREG32(RADEON_SURFACE0_INFO + surf_index, 0); +} diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c index 0e0e094da50..28e5777658b 100644 --- a/drivers/gpu/drm/radeon/r300.c +++ b/drivers/gpu/drm/radeon/r300.c @@ -30,6 +30,7 @@ #include "drm.h" #include "radeon_reg.h" #include "radeon.h" +#include "radeon_drm.h" /* r300,r350,rv350,rv370,rv380 depends on : */ void r100_hdp_reset(struct radeon_device *rdev); @@ -1023,7 +1024,7 @@ static int r300_packet0_check(struct radeon_cs_parser *p, struct radeon_cs_reloc *reloc; struct r300_cs_track *track; volatile uint32_t *ib; - uint32_t tmp; + uint32_t tmp, tile_flags = 0; unsigned i; int r; @@ -1052,7 +1053,19 @@ static int r300_packet0_check(struct radeon_cs_parser *p, } tmp = ib_chunk->kdata[idx] & 0x003fffff; tmp += (((u32)reloc->lobj.gpu_offset) >> 10); - ib[idx] = (ib_chunk->kdata[idx] & 0xffc00000) | tmp; + + if (reloc->lobj.tiling_flags & RADEON_TILING_MACRO) + tile_flags |= RADEON_DST_TILE_MACRO; + if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO) { + if (reg == RADEON_SRC_PITCH_OFFSET) { + DRM_ERROR("Cannot src blit from microtiled surface\n"); + r100_cs_dump_packet(p, pkt); + return -EINVAL; + } + tile_flags |= RADEON_DST_TILE_MICRO; + } + tmp |= tile_flags; + ib[idx] = (ib_chunk->kdata[idx] & 0x3fc00000) | tmp; break; case R300_RB3D_COLOROFFSET0: case R300_RB3D_COLOROFFSET1: @@ -1141,6 +1154,23 @@ static int r300_packet0_check(struct radeon_cs_parser *p, /* RB3D_COLORPITCH1 */ /* RB3D_COLORPITCH2 */ /* RB3D_COLORPITCH3 */ + r = r100_cs_packet_next_reloc(p, &reloc); + if (r) { + DRM_ERROR("No reloc for ib[%d]=0x%04X\n", + idx, reg); + r100_cs_dump_packet(p, pkt); + return r; + } + + if (reloc->lobj.tiling_flags & RADEON_TILING_MACRO) + tile_flags |= R300_COLOR_TILE_ENABLE; + if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO) + tile_flags |= R300_COLOR_MICROTILE_ENABLE; + + tmp = ib_chunk->kdata[idx] & ~(0x7 << 16); + tmp |= tile_flags; + ib[idx] = tmp; + i = (reg - 0x4E38) >> 2; track->cb[i].pitch = ib_chunk->kdata[idx] & 0x3FFE; switch (((ib_chunk->kdata[idx] >> 21) & 0xF)) { @@ -1196,6 +1226,23 @@ static int r300_packet0_check(struct radeon_cs_parser *p, break; case 0x4F24: /* ZB_DEPTHPITCH */ + r = r100_cs_packet_next_reloc(p, &reloc); + if (r) { + DRM_ERROR("No reloc for ib[%d]=0x%04X\n", + idx, reg); + r100_cs_dump_packet(p, pkt); + return r; + } + + if (reloc->lobj.tiling_flags & RADEON_TILING_MACRO) + tile_flags |= R300_DEPTHMACROTILE_ENABLE; + if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO) + tile_flags |= R300_DEPTHMICROTILE_TILED;; + + tmp = ib_chunk->kdata[idx] & ~(0x7 << 16); + tmp |= tile_flags; + ib[idx] = tmp; + track->zb.pitch = ib_chunk->kdata[idx] & 0x3FFC; break; case 0x4104: diff --git a/drivers/gpu/drm/radeon/r300_reg.h b/drivers/gpu/drm/radeon/r300_reg.h index 70f48609515..4b7afef35a6 100644 --- a/drivers/gpu/drm/radeon/r300_reg.h +++ b/drivers/gpu/drm/radeon/r300_reg.h @@ -27,7 +27,9 @@ #ifndef _R300_REG_H_ #define _R300_REG_H_ - +#define R300_SURF_TILE_MACRO (1<<16) +#define R300_SURF_TILE_MICRO (2<<16) +#define R300_SURF_TILE_BOTH (3<<16) #define R300_MC_INIT_MISC_LAT_TIMER 0x180 diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index 7f007185e7f..af12a2fe322 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -201,6 +201,14 @@ int radeon_fence_wait_last(struct radeon_device *rdev); struct radeon_fence *radeon_fence_ref(struct radeon_fence *fence); void radeon_fence_unref(struct radeon_fence **fence); +/* + * Tiling registers + */ +struct radeon_surface_reg { + struct radeon_object *robj; +}; + +#define RADEON_GEM_MAX_SURFACES 8 /* * Radeon buffer. @@ -213,6 +221,7 @@ struct radeon_object_list { uint64_t gpu_offset; unsigned rdomain; unsigned wdomain; + uint32_t tiling_flags; }; int radeon_object_init(struct radeon_device *rdev); @@ -242,8 +251,15 @@ void radeon_object_list_clean(struct list_head *head); int radeon_object_fbdev_mmap(struct radeon_object *robj, struct vm_area_struct *vma); unsigned long radeon_object_size(struct radeon_object *robj); - - +void radeon_object_clear_surface_reg(struct radeon_object *robj); +int radeon_object_check_tiling(struct radeon_object *robj, bool has_moved, + bool force_drop); +void radeon_object_set_tiling_flags(struct radeon_object *robj, + uint32_t tiling_flags, uint32_t pitch); +void radeon_object_get_tiling_flags(struct radeon_object *robj, uint32_t *tiling_flags, uint32_t *pitch); +void radeon_bo_move_notify(struct ttm_buffer_object *bo, + struct ttm_mem_reg *mem); +void radeon_bo_fault_reserve_notify(struct ttm_buffer_object *bo); /* * GEM objects. */ @@ -535,6 +551,11 @@ struct radeon_asic { void (*set_memory_clock)(struct radeon_device *rdev, uint32_t mem_clock); void (*set_pcie_lanes)(struct radeon_device *rdev, int lanes); void (*set_clock_gating)(struct radeon_device *rdev, int enable); + + int (*set_surface_reg)(struct radeon_device *rdev, int reg, + uint32_t tiling_flags, uint32_t pitch, + uint32_t offset, uint32_t obj_size); + int (*clear_surface_reg)(struct radeon_device *rdev, int reg); }; union radeon_asic_config { @@ -568,6 +589,10 @@ int radeon_gem_busy_ioctl(struct drm_device *dev, void *data, int radeon_gem_wait_idle_ioctl(struct drm_device *dev, void *data, struct drm_file *filp); int radeon_cs_ioctl(struct drm_device *dev, void *data, struct drm_file *filp); +int radeon_gem_set_tiling_ioctl(struct drm_device *dev, void *data, + struct drm_file *filp); +int radeon_gem_get_tiling_ioctl(struct drm_device *dev, void *data, + struct drm_file *filp); /* @@ -627,6 +652,7 @@ struct radeon_device { bool shutdown; bool suspend; bool need_dma32; + struct radeon_surface_reg surface_regs[RADEON_GEM_MAX_SURFACES]; }; int radeon_device_init(struct radeon_device *rdev, @@ -801,5 +827,7 @@ static inline void radeon_ring_write(struct radeon_device *rdev, uint32_t v) #define radeon_set_memory_clock(rdev, e) (rdev)->asic->set_engine_clock((rdev), (e)) #define radeon_set_pcie_lanes(rdev, l) (rdev)->asic->set_pcie_lanes((rdev), (l)) #define radeon_set_clock_gating(rdev, e) (rdev)->asic->set_clock_gating((rdev), (e)) +#define radeon_set_surface_reg(rdev, r, f, p, o, s) ((rdev)->asic->set_surface_reg((rdev), (r), (f), (p), (o), (s))) +#define radeon_clear_surface_reg(rdev, r) ((rdev)->asic->clear_surface_reg((rdev), (r))) #endif diff --git a/drivers/gpu/drm/radeon/radeon_asic.h b/drivers/gpu/drm/radeon/radeon_asic.h index e2e567395df..dd903d32940 100644 --- a/drivers/gpu/drm/radeon/radeon_asic.h +++ b/drivers/gpu/drm/radeon/radeon_asic.h @@ -71,6 +71,10 @@ int r100_copy_blit(struct radeon_device *rdev, uint64_t dst_offset, unsigned num_pages, struct radeon_fence *fence); +int r100_set_surface_reg(struct radeon_device *rdev, int reg, + uint32_t tiling_flags, uint32_t pitch, + uint32_t offset, uint32_t obj_size); +int r100_clear_surface_reg(struct radeon_device *rdev, int reg); static struct radeon_asic r100_asic = { .init = &r100_init, @@ -100,6 +104,8 @@ static struct radeon_asic r100_asic = { .set_memory_clock = NULL, .set_pcie_lanes = NULL, .set_clock_gating = &radeon_legacy_set_clock_gating, + .set_surface_reg = r100_set_surface_reg, + .clear_surface_reg = r100_clear_surface_reg, }; @@ -128,6 +134,7 @@ int r300_copy_dma(struct radeon_device *rdev, uint64_t dst_offset, unsigned num_pages, struct radeon_fence *fence); + static struct radeon_asic r300_asic = { .init = &r300_init, .errata = &r300_errata, @@ -156,6 +163,8 @@ static struct radeon_asic r300_asic = { .set_memory_clock = NULL, .set_pcie_lanes = &rv370_set_pcie_lanes, .set_clock_gating = &radeon_legacy_set_clock_gating, + .set_surface_reg = r100_set_surface_reg, + .clear_surface_reg = r100_clear_surface_reg, }; /* @@ -193,6 +202,8 @@ static struct radeon_asic r420_asic = { .set_memory_clock = &radeon_atom_set_memory_clock, .set_pcie_lanes = &rv370_set_pcie_lanes, .set_clock_gating = &radeon_atom_set_clock_gating, + .set_surface_reg = r100_set_surface_reg, + .clear_surface_reg = r100_clear_surface_reg, }; @@ -237,6 +248,8 @@ static struct radeon_asic rs400_asic = { .set_memory_clock = NULL, .set_pcie_lanes = NULL, .set_clock_gating = &radeon_legacy_set_clock_gating, + .set_surface_reg = r100_set_surface_reg, + .clear_surface_reg = r100_clear_surface_reg, }; @@ -322,6 +335,8 @@ static struct radeon_asic rs690_asic = { .set_memory_clock = &radeon_atom_set_memory_clock, .set_pcie_lanes = NULL, .set_clock_gating = &radeon_atom_set_clock_gating, + .set_surface_reg = r100_set_surface_reg, + .clear_surface_reg = r100_clear_surface_reg, }; @@ -367,6 +382,8 @@ static struct radeon_asic rv515_asic = { .set_memory_clock = &radeon_atom_set_memory_clock, .set_pcie_lanes = &rv370_set_pcie_lanes, .set_clock_gating = &radeon_atom_set_clock_gating, + .set_surface_reg = r100_set_surface_reg, + .clear_surface_reg = r100_clear_surface_reg, }; @@ -405,6 +422,8 @@ static struct radeon_asic r520_asic = { .set_memory_clock = &radeon_atom_set_memory_clock, .set_pcie_lanes = &rv370_set_pcie_lanes, .set_clock_gating = &radeon_atom_set_clock_gating, + .set_surface_reg = r100_set_surface_reg, + .clear_surface_reg = r100_clear_surface_reg, }; /* diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c index cdef6eb01ba..f23083bbba3 100644 --- a/drivers/gpu/drm/radeon/radeon_device.c +++ b/drivers/gpu/drm/radeon/radeon_device.c @@ -48,6 +48,8 @@ static void radeon_surface_init(struct radeon_device *rdev) i * (RADEON_SURFACE1_INFO - RADEON_SURFACE0_INFO), 0); } + /* enable surfaces */ + WREG32(RADEON_SURFACE_CNTL, 0); } } diff --git a/drivers/gpu/drm/radeon/radeon_fb.c b/drivers/gpu/drm/radeon/radeon_fb.c index 260870a29d8..36d2f5588f2 100644 --- a/drivers/gpu/drm/radeon/radeon_fb.c +++ b/drivers/gpu/drm/radeon/radeon_fb.c @@ -471,10 +471,10 @@ static struct notifier_block paniced = { .notifier_call = radeonfb_panic, }; -static int radeon_align_pitch(struct radeon_device *rdev, int width, int bpp) +static int radeon_align_pitch(struct radeon_device *rdev, int width, int bpp, bool tiled) { int aligned = width; - int align_large = (ASIC_IS_AVIVO(rdev)); + int align_large = (ASIC_IS_AVIVO(rdev)) || tiled; int pitch_mask = 0; switch (bpp / 8) { @@ -512,12 +512,13 @@ int radeonfb_create(struct radeon_device *rdev, u64 fb_gpuaddr; void *fbptr = NULL; unsigned long tmp; + bool fb_tiled = false; /* useful for testing */ mode_cmd.width = surface_width; mode_cmd.height = surface_height; mode_cmd.bpp = 32; /* need to align pitch with crtc limits */ - mode_cmd.pitch = radeon_align_pitch(rdev, mode_cmd.width, mode_cmd.bpp) * ((mode_cmd.bpp + 1) / 8); + mode_cmd.pitch = radeon_align_pitch(rdev, mode_cmd.width, mode_cmd.bpp, fb_tiled) * ((mode_cmd.bpp + 1) / 8); mode_cmd.depth = 24; size = mode_cmd.pitch * mode_cmd.height; @@ -535,6 +536,8 @@ int radeonfb_create(struct radeon_device *rdev, } robj = gobj->driver_private; + if (fb_tiled) + radeon_object_set_tiling_flags(robj, RADEON_TILING_MACRO|RADEON_TILING_SURFACE, mode_cmd.pitch); mutex_lock(&rdev->ddev->struct_mutex); fb = radeon_framebuffer_create(rdev->ddev, &mode_cmd, gobj); if (fb == NULL) { @@ -563,6 +566,9 @@ int radeonfb_create(struct radeon_device *rdev, } rfbdev = info->par; + if (fb_tiled) + radeon_object_check_tiling(robj, 0, 0); + ret = radeon_object_kmap(robj, &fbptr); if (ret) { goto out_unref; diff --git a/drivers/gpu/drm/radeon/radeon_gem.c b/drivers/gpu/drm/radeon/radeon_gem.c index eb516034235..12542087b29 100644 --- a/drivers/gpu/drm/radeon/radeon_gem.c +++ b/drivers/gpu/drm/radeon/radeon_gem.c @@ -285,3 +285,44 @@ int radeon_gem_wait_idle_ioctl(struct drm_device *dev, void *data, mutex_unlock(&dev->struct_mutex); return r; } + +int radeon_gem_set_tiling_ioctl(struct drm_device *dev, void *data, + struct drm_file *filp) +{ + struct drm_radeon_gem_set_tiling *args = data; + struct drm_gem_object *gobj; + struct radeon_object *robj; + int r = 0; + + DRM_DEBUG("%d \n", args->handle); + gobj = drm_gem_object_lookup(dev, filp, args->handle); + if (gobj == NULL) + return -EINVAL; + robj = gobj->driver_private; + radeon_object_set_tiling_flags(robj, args->tiling_flags, args->pitch); + mutex_lock(&dev->struct_mutex); + drm_gem_object_unreference(gobj); + mutex_unlock(&dev->struct_mutex); + return r; +} + +int radeon_gem_get_tiling_ioctl(struct drm_device *dev, void *data, + struct drm_file *filp) +{ + struct drm_radeon_gem_get_tiling *args = data; + struct drm_gem_object *gobj; + struct radeon_object *robj; + int r = 0; + + DRM_DEBUG("\n"); + gobj = drm_gem_object_lookup(dev, filp, args->handle); + if (gobj == NULL) + return -EINVAL; + robj = gobj->driver_private; + radeon_object_get_tiling_flags(robj, &args->tiling_flags, + &args->pitch); + mutex_lock(&dev->struct_mutex); + drm_gem_object_unreference(gobj); + mutex_unlock(&dev->struct_mutex); + return r; +} diff --git a/drivers/gpu/drm/radeon/radeon_kms.c b/drivers/gpu/drm/radeon/radeon_kms.c index 4612a7c146d..937a2f1cdb4 100644 --- a/drivers/gpu/drm/radeon/radeon_kms.c +++ b/drivers/gpu/drm/radeon/radeon_kms.c @@ -291,5 +291,7 @@ struct drm_ioctl_desc radeon_ioctls_kms[] = { DRM_IOCTL_DEF(DRM_RADEON_GEM_WAIT_IDLE, radeon_gem_wait_idle_ioctl, DRM_AUTH), DRM_IOCTL_DEF(DRM_RADEON_CS, radeon_cs_ioctl, DRM_AUTH), DRM_IOCTL_DEF(DRM_RADEON_INFO, radeon_info_ioctl, DRM_AUTH), + DRM_IOCTL_DEF(DRM_RADEON_GEM_SET_TILING, radeon_gem_set_tiling_ioctl, DRM_AUTH), + DRM_IOCTL_DEF(DRM_RADEON_GEM_GET_TILING, radeon_gem_get_tiling_ioctl, DRM_AUTH), }; int radeon_max_kms_ioctl = DRM_ARRAY_SIZE(radeon_ioctls_kms); diff --git a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c index 14c1a5107fc..0613790e2a5 100644 --- a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c +++ b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c @@ -235,6 +235,7 @@ int radeon_crtc_set_base(struct drm_crtc *crtc, int x, int y, uint64_t base; uint32_t crtc_offset, crtc_offset_cntl, crtc_tile_x0_y0 = 0; uint32_t crtc_pitch, pitch_pixels; + uint32_t tiling_flags; DRM_DEBUG("\n"); @@ -258,8 +259,12 @@ int radeon_crtc_set_base(struct drm_crtc *crtc, int x, int y, (crtc->fb->bits_per_pixel * 8)); crtc_pitch |= crtc_pitch << 16; - /* TODO tiling */ - if (0) { + radeon_object_get_tiling_flags(obj->driver_private, + &tiling_flags, NULL); + if (tiling_flags & RADEON_TILING_MICRO) + DRM_ERROR("trying to scanout microtiled buffer\n"); + + if (tiling_flags & RADEON_TILING_MACRO) { if (ASIC_IS_R300(rdev)) crtc_offset_cntl |= (R300_CRTC_X_Y_MODE_EN | R300_CRTC_MICRO_TILE_BUFFER_DIS | @@ -275,15 +280,13 @@ int radeon_crtc_set_base(struct drm_crtc *crtc, int x, int y, crtc_offset_cntl &= ~RADEON_CRTC_TILE_EN; } - - /* TODO more tiling */ - if (0) { + if (tiling_flags & RADEON_TILING_MACRO) { if (ASIC_IS_R300(rdev)) { crtc_tile_x0_y0 = x | (y << 16); base &= ~0x7ff; } else { int byteshift = crtc->fb->bits_per_pixel >> 4; - int tile_addr = (((y >> 3) * crtc->fb->width + x) >> (8 - byteshift)) << 11; + int tile_addr = (((y >> 3) * pitch_pixels + x) >> (8 - byteshift)) << 11; base += tile_addr + ((x << byteshift) % 256) + ((y % 8) << 8); crtc_offset_cntl |= (y % 16); } diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c index bac0d06c52a..d5b1fd562d8 100644 --- a/drivers/gpu/drm/radeon/radeon_object.c +++ b/drivers/gpu/drm/radeon/radeon_object.c @@ -44,6 +44,9 @@ struct radeon_object { uint64_t gpu_addr; void *kptr; bool is_iomem; + uint32_t tiling_flags; + uint32_t pitch; + int surface_reg; }; int radeon_ttm_init(struct radeon_device *rdev); @@ -70,6 +73,7 @@ static void radeon_ttm_object_object_destroy(struct ttm_buffer_object *tobj) robj = container_of(tobj, struct radeon_object, tobj); list_del_init(&robj->list); + radeon_object_clear_surface_reg(robj); kfree(robj); } @@ -141,6 +145,7 @@ int radeon_object_create(struct radeon_device *rdev, } robj->rdev = rdev; robj->gobj = gobj; + robj->surface_reg = -1; INIT_LIST_HEAD(&robj->list); flags = radeon_object_flags_from_domain(domain); @@ -435,6 +440,7 @@ int radeon_object_list_validate(struct list_head *head, void *fence) radeon_object_gpu_addr(robj); } lobj->gpu_offset = robj->gpu_addr; + lobj->tiling_flags = robj->tiling_flags; if (fence) { old_fence = (struct radeon_fence *)robj->tobj.sync_obj; robj->tobj.sync_obj = radeon_fence_ref(fence); @@ -479,3 +485,127 @@ unsigned long radeon_object_size(struct radeon_object *robj) { return robj->tobj.num_pages << PAGE_SHIFT; } + +int radeon_object_get_surface_reg(struct radeon_object *robj) +{ + struct radeon_device *rdev = robj->rdev; + struct radeon_surface_reg *reg; + struct radeon_object *old_object; + int steal; + int i; + + if (!robj->tiling_flags) + return 0; + + if (robj->surface_reg >= 0) { + reg = &rdev->surface_regs[robj->surface_reg]; + i = robj->surface_reg; + goto out; + } + + steal = -1; + for (i = 0; i < RADEON_GEM_MAX_SURFACES; i++) { + + reg = &rdev->surface_regs[i]; + if (!reg->robj) + break; + + old_object = reg->robj; + if (old_object->pin_count == 0) + steal = i; + } + + /* if we are all out */ + if (i == RADEON_GEM_MAX_SURFACES) { + if (steal == -1) + return -ENOMEM; + /* find someone with a surface reg and nuke their BO */ + reg = &rdev->surface_regs[steal]; + old_object = reg->robj; + /* blow away the mapping */ + DRM_DEBUG("stealing surface reg %d from %p\n", steal, old_object); + ttm_bo_unmap_virtual(&old_object->tobj); + old_object->surface_reg = -1; + i = steal; + } + + robj->surface_reg = i; + reg->robj = robj; + +out: + radeon_set_surface_reg(rdev, i, robj->tiling_flags, robj->pitch, + robj->tobj.mem.mm_node->start << PAGE_SHIFT, + robj->tobj.num_pages << PAGE_SHIFT); + return 0; +} + +void radeon_object_clear_surface_reg(struct radeon_object *robj) +{ + struct radeon_device *rdev = robj->rdev; + struct radeon_surface_reg *reg; + + if (robj->surface_reg == -1) + return; + + reg = &rdev->surface_regs[robj->surface_reg]; + radeon_clear_surface_reg(rdev, robj->surface_reg); + + reg->robj = NULL; + robj->surface_reg = -1; +} + +void radeon_object_set_tiling_flags(struct radeon_object *robj, + uint32_t tiling_flags, uint32_t pitch) +{ + robj->tiling_flags = tiling_flags; + robj->pitch = pitch; +} + +void radeon_object_get_tiling_flags(struct radeon_object *robj, + uint32_t *tiling_flags, + uint32_t *pitch) +{ + if (tiling_flags) + *tiling_flags = robj->tiling_flags; + if (pitch) + *pitch = robj->pitch; +} + +int radeon_object_check_tiling(struct radeon_object *robj, bool has_moved, + bool force_drop) +{ + if (!(robj->tiling_flags & RADEON_TILING_SURFACE)) + return 0; + + if (force_drop) { + radeon_object_clear_surface_reg(robj); + return 0; + } + + if (robj->tobj.mem.mem_type != TTM_PL_VRAM) { + if (!has_moved) + return 0; + + if (robj->surface_reg >= 0) + radeon_object_clear_surface_reg(robj); + return 0; + } + + if ((robj->surface_reg >= 0) && !has_moved) + return 0; + + return radeon_object_get_surface_reg(robj); +} + +void radeon_bo_move_notify(struct ttm_buffer_object *bo, + struct ttm_mem_reg *mem) +{ + struct radeon_object *robj = container_of(bo, struct radeon_object, tobj); + radeon_object_check_tiling(robj, 0, 1); +} + +void radeon_bo_fault_reserve_notify(struct ttm_buffer_object *bo) +{ + struct radeon_object *robj = container_of(bo, struct radeon_object, tobj); + radeon_object_check_tiling(robj, 0, 0); +} diff --git a/drivers/gpu/drm/radeon/radeon_ttm.c b/drivers/gpu/drm/radeon/radeon_ttm.c index 4ca9aa9203d..37e1cbcce3a 100644 --- a/drivers/gpu/drm/radeon/radeon_ttm.c +++ b/drivers/gpu/drm/radeon/radeon_ttm.c @@ -429,6 +429,8 @@ static struct ttm_bo_driver radeon_bo_driver = { .sync_obj_flush = &radeon_sync_obj_flush, .sync_obj_unref = &radeon_sync_obj_unref, .sync_obj_ref = &radeon_sync_obj_ref, + .move_notify = &radeon_bo_move_notify, + .fault_reserve_notify = &radeon_bo_fault_reserve_notify, }; int radeon_ttm_init(struct radeon_device *rdev) diff --git a/drivers/gpu/drm/ttm/ttm_bo.c b/drivers/gpu/drm/ttm/ttm_bo.c index e55e7972c89..6538d423698 100644 --- a/drivers/gpu/drm/ttm/ttm_bo.c +++ b/drivers/gpu/drm/ttm/ttm_bo.c @@ -43,7 +43,6 @@ #define TTM_BO_HASH_ORDER 13 static int ttm_bo_setup_vm(struct ttm_buffer_object *bo); -static void ttm_bo_unmap_virtual(struct ttm_buffer_object *bo); static int ttm_bo_swapout(struct ttm_mem_shrink *shrink); static inline uint32_t ttm_bo_type_flags(unsigned type) @@ -307,6 +306,9 @@ static int ttm_bo_handle_move_mem(struct ttm_buffer_object *bo, } + if (bdev->driver->move_notify) + bdev->driver->move_notify(bo, mem); + if (!(old_man->flags & TTM_MEMTYPE_FLAG_FIXED) && !(new_man->flags & TTM_MEMTYPE_FLAG_FIXED)) ret = ttm_bo_move_ttm(bo, evict, no_wait, mem); @@ -1451,6 +1453,7 @@ void ttm_bo_unmap_virtual(struct ttm_buffer_object *bo) unmap_mapping_range(bdev->dev_mapping, offset, holelen, 1); } +EXPORT_SYMBOL(ttm_bo_unmap_virtual); static void ttm_bo_vm_insert_rb(struct ttm_buffer_object *bo) { diff --git a/drivers/gpu/drm/ttm/ttm_bo_vm.c b/drivers/gpu/drm/ttm/ttm_bo_vm.c index 40b75032ea4..41c907f6c56 100644 --- a/drivers/gpu/drm/ttm/ttm_bo_vm.c +++ b/drivers/gpu/drm/ttm/ttm_bo_vm.c @@ -101,6 +101,9 @@ static int ttm_bo_vm_fault(struct vm_area_struct *vma, struct vm_fault *vmf) return VM_FAULT_NOPAGE; } + if (bdev->driver->fault_reserve_notify) + bdev->driver->fault_reserve_notify(bo); + /* * Wait for buffer data in transit, due to a pipelined * move. diff --git a/include/drm/radeon_drm.h b/include/drm/radeon_drm.h index 41862e9a4c2..af4b4826997 100644 --- a/include/drm/radeon_drm.h +++ b/include/drm/radeon_drm.h @@ -506,6 +506,8 @@ typedef struct { #define DRM_RADEON_GEM_WAIT_IDLE 0x24 #define DRM_RADEON_CS 0x26 #define DRM_RADEON_INFO 0x27 +#define DRM_RADEON_GEM_SET_TILING 0x28 +#define DRM_RADEON_GEM_GET_TILING 0x29 #define DRM_IOCTL_RADEON_CP_INIT DRM_IOW( DRM_COMMAND_BASE + DRM_RADEON_CP_INIT, drm_radeon_init_t) #define DRM_IOCTL_RADEON_CP_START DRM_IO( DRM_COMMAND_BASE + DRM_RADEON_CP_START) @@ -544,7 +546,8 @@ typedef struct { #define DRM_IOCTL_RADEON_GEM_WAIT_IDLE DRM_IOW(DRM_COMMAND_BASE + DRM_RADEON_GEM_WAIT_IDLE, struct drm_radeon_gem_wait_idle) #define DRM_IOCTL_RADEON_CS DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_CS, struct drm_radeon_cs) #define DRM_IOCTL_RADEON_INFO DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_INFO, struct drm_radeon_info) - +#define DRM_IOCTL_RADEON_SET_TILING DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_GEM_SET_TILING, struct drm_radeon_gem_set_tiling) +#define DRM_IOCTL_RADEON_GET_TILING DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_GEM_GET_TILING, struct drm_radeon_gem_get_tiling) typedef struct drm_radeon_init { enum { @@ -796,6 +799,24 @@ struct drm_radeon_gem_create { uint32_t flags; }; +#define RADEON_TILING_MACRO 0x1 +#define RADEON_TILING_MICRO 0x2 +#define RADEON_TILING_SWAP 0x4 +#define RADEON_TILING_SURFACE 0x8 /* this object requires a surface + * when mapped - i.e. front buffer */ + +struct drm_radeon_gem_set_tiling { + uint32_t handle; + uint32_t tiling_flags; + uint32_t pitch; +}; + +struct drm_radeon_gem_get_tiling { + uint32_t handle; + uint32_t tiling_flags; + uint32_t pitch; +}; + struct drm_radeon_gem_mmap { uint32_t handle; uint32_t pad; diff --git a/include/drm/ttm/ttm_bo_driver.h b/include/drm/ttm/ttm_bo_driver.h index ea83dd23a4d..a68829db381 100644 --- a/include/drm/ttm/ttm_bo_driver.h +++ b/include/drm/ttm/ttm_bo_driver.h @@ -354,6 +354,14 @@ struct ttm_bo_driver { int (*sync_obj_flush) (void *sync_obj, void *sync_arg); void (*sync_obj_unref) (void **sync_obj); void *(*sync_obj_ref) (void *sync_obj); + + /* hook to notify driver about a driver move so it + * can do tiling things */ + void (*move_notify)(struct ttm_buffer_object *bo, + struct ttm_mem_reg *new_mem); + /* notify the driver we are taking a fault on this BO + * and have reserved it */ + void (*fault_reserve_notify)(struct ttm_buffer_object *bo); }; #define TTM_NUM_MEM_TYPES 8 @@ -653,6 +661,13 @@ extern int ttm_bo_device_init(struct ttm_bo_device *bdev, struct ttm_bo_driver *driver, uint64_t file_page_offset, bool need_dma32); +/** + * ttm_bo_unmap_virtual + * + * @bo: tear down the virtual mappings for this BO + */ +extern void ttm_bo_unmap_virtual(struct ttm_buffer_object *bo); + /** * ttm_bo_reserve: * -- GitLab From c93bb85b5cba3e3a06f2cad8e9bc5c23d3d10aac Mon Sep 17 00:00:00 2001 From: Jerome Glisse Date: Mon, 13 Jul 2009 21:04:08 +0200 Subject: [PATCH 0461/1342] drm/radeon/kms: fix bandwidth computation on avivo hardware Fix bandwidth computation and crtc priority in memory controller so that crtc memory request are fullfill in time to avoid display artifact. Signed-off-by: Jerome Glisse Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/atombios_crtc.c | 276 +++---- drivers/gpu/drm/radeon/r100.c | 483 +++++++++++ drivers/gpu/drm/radeon/r300.c | 1 + drivers/gpu/drm/radeon/r520.c | 14 + drivers/gpu/drm/radeon/radeon.h | 40 +- drivers/gpu/drm/radeon/radeon_asic.h | 13 + drivers/gpu/drm/radeon/radeon_device.c | 10 +- drivers/gpu/drm/radeon/radeon_display.c | 68 +- drivers/gpu/drm/radeon/radeon_encoders.c | 369 +-------- drivers/gpu/drm/radeon/radeon_legacy_crtc.c | 661 ++++----------- .../gpu/drm/radeon/radeon_legacy_encoders.c | 188 +---- drivers/gpu/drm/radeon/radeon_mode.h | 48 +- drivers/gpu/drm/radeon/radeon_share.h | 39 + drivers/gpu/drm/radeon/rs400.c | 1 + drivers/gpu/drm/radeon/rs600.c | 5 + drivers/gpu/drm/radeon/rs690.c | 472 +++++++++++ drivers/gpu/drm/radeon/rs690r.h | 99 +++ drivers/gpu/drm/radeon/rv515.c | 774 +++++++++++++++--- drivers/gpu/drm/radeon/rv515r.h | 170 ++++ 19 files changed, 2377 insertions(+), 1354 deletions(-) create mode 100644 drivers/gpu/drm/radeon/radeon_share.h create mode 100644 drivers/gpu/drm/radeon/rs690r.h create mode 100644 drivers/gpu/drm/radeon/rv515r.h diff --git a/drivers/gpu/drm/radeon/atombios_crtc.c b/drivers/gpu/drm/radeon/atombios_crtc.c index eac26cdb5da..74d034f77c6 100644 --- a/drivers/gpu/drm/radeon/atombios_crtc.c +++ b/drivers/gpu/drm/radeon/atombios_crtc.c @@ -31,6 +31,132 @@ #include "atom.h" #include "atom-bits.h" +static void atombios_overscan_setup(struct drm_crtc *crtc, + struct drm_display_mode *mode, + struct drm_display_mode *adjusted_mode) +{ + struct drm_device *dev = crtc->dev; + struct radeon_device *rdev = dev->dev_private; + struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc); + SET_CRTC_OVERSCAN_PS_ALLOCATION args; + int index = GetIndexIntoMasterTable(COMMAND, SetCRTC_OverScan); + int a1, a2; + + memset(&args, 0, sizeof(args)); + + args.usOverscanRight = 0; + args.usOverscanLeft = 0; + args.usOverscanBottom = 0; + args.usOverscanTop = 0; + args.ucCRTC = radeon_crtc->crtc_id; + + switch (radeon_crtc->rmx_type) { + case RMX_CENTER: + args.usOverscanTop = (adjusted_mode->crtc_vdisplay - mode->crtc_vdisplay) / 2; + args.usOverscanBottom = (adjusted_mode->crtc_vdisplay - mode->crtc_vdisplay) / 2; + args.usOverscanLeft = (adjusted_mode->crtc_hdisplay - mode->crtc_hdisplay) / 2; + args.usOverscanRight = (adjusted_mode->crtc_hdisplay - mode->crtc_hdisplay) / 2; + atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args); + break; + case RMX_ASPECT: + a1 = mode->crtc_vdisplay * adjusted_mode->crtc_hdisplay; + a2 = adjusted_mode->crtc_vdisplay * mode->crtc_hdisplay; + + if (a1 > a2) { + args.usOverscanLeft = (adjusted_mode->crtc_hdisplay - (a2 / mode->crtc_vdisplay)) / 2; + args.usOverscanRight = (adjusted_mode->crtc_hdisplay - (a2 / mode->crtc_vdisplay)) / 2; + } else if (a2 > a1) { + args.usOverscanLeft = (adjusted_mode->crtc_vdisplay - (a1 / mode->crtc_hdisplay)) / 2; + args.usOverscanRight = (adjusted_mode->crtc_vdisplay - (a1 / mode->crtc_hdisplay)) / 2; + } + atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args); + break; + case RMX_FULL: + default: + args.usOverscanRight = 0; + args.usOverscanLeft = 0; + args.usOverscanBottom = 0; + args.usOverscanTop = 0; + atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args); + break; + } +} + +static void atombios_scaler_setup(struct drm_crtc *crtc) +{ + struct drm_device *dev = crtc->dev; + struct radeon_device *rdev = dev->dev_private; + struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc); + ENABLE_SCALER_PS_ALLOCATION args; + int index = GetIndexIntoMasterTable(COMMAND, EnableScaler); + /* fixme - fill in enc_priv for atom dac */ + enum radeon_tv_std tv_std = TV_STD_NTSC; + + if (!ASIC_IS_AVIVO(rdev) && radeon_crtc->crtc_id) + return; + + memset(&args, 0, sizeof(args)); + + args.ucScaler = radeon_crtc->crtc_id; + + if (radeon_crtc->devices & (ATOM_DEVICE_TV_SUPPORT)) { + switch (tv_std) { + case TV_STD_NTSC: + default: + args.ucTVStandard = ATOM_TV_NTSC; + break; + case TV_STD_PAL: + args.ucTVStandard = ATOM_TV_PAL; + break; + case TV_STD_PAL_M: + args.ucTVStandard = ATOM_TV_PALM; + break; + case TV_STD_PAL_60: + args.ucTVStandard = ATOM_TV_PAL60; + break; + case TV_STD_NTSC_J: + args.ucTVStandard = ATOM_TV_NTSCJ; + break; + case TV_STD_SCART_PAL: + args.ucTVStandard = ATOM_TV_PAL; /* ??? */ + break; + case TV_STD_SECAM: + args.ucTVStandard = ATOM_TV_SECAM; + break; + case TV_STD_PAL_CN: + args.ucTVStandard = ATOM_TV_PALCN; + break; + } + args.ucEnable = SCALER_ENABLE_MULTITAP_MODE; + } else if (radeon_crtc->devices & (ATOM_DEVICE_CV_SUPPORT)) { + args.ucTVStandard = ATOM_TV_CV; + args.ucEnable = SCALER_ENABLE_MULTITAP_MODE; + } else { + switch (radeon_crtc->rmx_type) { + case RMX_FULL: + args.ucEnable = ATOM_SCALER_EXPANSION; + break; + case RMX_CENTER: + args.ucEnable = ATOM_SCALER_CENTER; + break; + case RMX_ASPECT: + args.ucEnable = ATOM_SCALER_EXPANSION; + break; + default: + if (ASIC_IS_AVIVO(rdev)) + args.ucEnable = ATOM_SCALER_DISABLE; + else + args.ucEnable = ATOM_SCALER_CENTER; + break; + } + } + atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args); + if (radeon_crtc->devices & (ATOM_DEVICE_CV_SUPPORT | ATOM_DEVICE_TV_SUPPORT) + && rdev->family >= CHIP_RV515 && rdev->family <= CHIP_RV570) { + atom_rv515_force_tv_scaler(rdev); + } +} + static void atombios_lock_crtc(struct drm_crtc *crtc, int lock) { struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc); @@ -522,6 +648,9 @@ int atombios_crtc_mode_set(struct drm_crtc *crtc, radeon_crtc_set_base(crtc, x, y, old_fb); radeon_legacy_atom_set_surface(crtc); } + atombios_overscan_setup(crtc, mode, adjusted_mode); + atombios_scaler_setup(crtc); + radeon_bandwidth_update(rdev); return 0; } @@ -529,6 +658,8 @@ static bool atombios_crtc_mode_fixup(struct drm_crtc *crtc, struct drm_display_mode *mode, struct drm_display_mode *adjusted_mode) { + if (!radeon_crtc_scaling_mode_fixup(crtc, mode, adjusted_mode)) + return false; return true; } @@ -561,148 +692,3 @@ void radeon_atombios_init_crtc(struct drm_device *dev, AVIVO_D2CRTC_H_TOTAL - AVIVO_D1CRTC_H_TOTAL; drm_crtc_helper_add(&radeon_crtc->base, &atombios_helper_funcs); } - -void radeon_init_disp_bw_avivo(struct drm_device *dev, - struct drm_display_mode *mode1, - uint32_t pixel_bytes1, - struct drm_display_mode *mode2, - uint32_t pixel_bytes2) -{ - struct radeon_device *rdev = dev->dev_private; - fixed20_12 min_mem_eff; - fixed20_12 peak_disp_bw, mem_bw, pix_clk, pix_clk2, temp_ff; - fixed20_12 sclk_ff, mclk_ff; - uint32_t dc_lb_memory_split, temp; - - min_mem_eff.full = rfixed_const_8(0); - if (rdev->disp_priority == 2) { - uint32_t mc_init_misc_lat_timer = 0; - if (rdev->family == CHIP_RV515) - mc_init_misc_lat_timer = - RREG32_MC(RV515_MC_INIT_MISC_LAT_TIMER); - else if (rdev->family == CHIP_RS690) - mc_init_misc_lat_timer = - RREG32_MC(RS690_MC_INIT_MISC_LAT_TIMER); - - mc_init_misc_lat_timer &= - ~(R300_MC_DISP1R_INIT_LAT_MASK << - R300_MC_DISP1R_INIT_LAT_SHIFT); - mc_init_misc_lat_timer &= - ~(R300_MC_DISP0R_INIT_LAT_MASK << - R300_MC_DISP0R_INIT_LAT_SHIFT); - - if (mode2) - mc_init_misc_lat_timer |= - (1 << R300_MC_DISP1R_INIT_LAT_SHIFT); - if (mode1) - mc_init_misc_lat_timer |= - (1 << R300_MC_DISP0R_INIT_LAT_SHIFT); - - if (rdev->family == CHIP_RV515) - WREG32_MC(RV515_MC_INIT_MISC_LAT_TIMER, - mc_init_misc_lat_timer); - else if (rdev->family == CHIP_RS690) - WREG32_MC(RS690_MC_INIT_MISC_LAT_TIMER, - mc_init_misc_lat_timer); - } - - /* - * determine is there is enough bw for current mode - */ - temp_ff.full = rfixed_const(100); - mclk_ff.full = rfixed_const(rdev->clock.default_mclk); - mclk_ff.full = rfixed_div(mclk_ff, temp_ff); - sclk_ff.full = rfixed_const(rdev->clock.default_sclk); - sclk_ff.full = rfixed_div(sclk_ff, temp_ff); - - temp = (rdev->mc.vram_width / 8) * (rdev->mc.vram_is_ddr ? 2 : 1); - temp_ff.full = rfixed_const(temp); - mem_bw.full = rfixed_mul(mclk_ff, temp_ff); - mem_bw.full = rfixed_mul(mem_bw, min_mem_eff); - - pix_clk.full = 0; - pix_clk2.full = 0; - peak_disp_bw.full = 0; - if (mode1) { - temp_ff.full = rfixed_const(1000); - pix_clk.full = rfixed_const(mode1->clock); /* convert to fixed point */ - pix_clk.full = rfixed_div(pix_clk, temp_ff); - temp_ff.full = rfixed_const(pixel_bytes1); - peak_disp_bw.full += rfixed_mul(pix_clk, temp_ff); - } - if (mode2) { - temp_ff.full = rfixed_const(1000); - pix_clk2.full = rfixed_const(mode2->clock); /* convert to fixed point */ - pix_clk2.full = rfixed_div(pix_clk2, temp_ff); - temp_ff.full = rfixed_const(pixel_bytes2); - peak_disp_bw.full += rfixed_mul(pix_clk2, temp_ff); - } - - if (peak_disp_bw.full >= mem_bw.full) { - DRM_ERROR - ("You may not have enough display bandwidth for current mode\n" - "If you have flickering problem, try to lower resolution, refresh rate, or color depth\n"); - printk("peak disp bw %d, mem_bw %d\n", - rfixed_trunc(peak_disp_bw), rfixed_trunc(mem_bw)); - } - - /* - * Line Buffer Setup - * There is a single line buffer shared by both display controllers. - * DC_LB_MEMORY_SPLIT controls how that line buffer is shared between the display - * controllers. The paritioning can either be done manually or via one of four - * preset allocations specified in bits 1:0: - * 0 - line buffer is divided in half and shared between each display controller - * 1 - D1 gets 3/4 of the line buffer, D2 gets 1/4 - * 2 - D1 gets the whole buffer - * 3 - D1 gets 1/4 of the line buffer, D2 gets 3/4 - * Setting bit 2 of DC_LB_MEMORY_SPLIT controls switches to manual allocation mode. - * In manual allocation mode, D1 always starts at 0, D1 end/2 is specified in bits - * 14:4; D2 allocation follows D1. - */ - - /* is auto or manual better ? */ - dc_lb_memory_split = - RREG32(AVIVO_DC_LB_MEMORY_SPLIT) & ~AVIVO_DC_LB_MEMORY_SPLIT_MASK; - dc_lb_memory_split &= ~AVIVO_DC_LB_MEMORY_SPLIT_SHIFT_MODE; -#if 1 - /* auto */ - if (mode1 && mode2) { - if (mode1->hdisplay > mode2->hdisplay) { - if (mode1->hdisplay > 2560) - dc_lb_memory_split |= - AVIVO_DC_LB_MEMORY_SPLIT_D1_3Q_D2_1Q; - else - dc_lb_memory_split |= - AVIVO_DC_LB_MEMORY_SPLIT_D1HALF_D2HALF; - } else if (mode2->hdisplay > mode1->hdisplay) { - if (mode2->hdisplay > 2560) - dc_lb_memory_split |= - AVIVO_DC_LB_MEMORY_SPLIT_D1_1Q_D2_3Q; - else - dc_lb_memory_split |= - AVIVO_DC_LB_MEMORY_SPLIT_D1HALF_D2HALF; - } else - dc_lb_memory_split |= - AVIVO_DC_LB_MEMORY_SPLIT_D1HALF_D2HALF; - } else if (mode1) { - dc_lb_memory_split |= AVIVO_DC_LB_MEMORY_SPLIT_D1_ONLY; - } else if (mode2) { - dc_lb_memory_split |= AVIVO_DC_LB_MEMORY_SPLIT_D1_1Q_D2_3Q; - } -#else - /* manual */ - dc_lb_memory_split |= AVIVO_DC_LB_MEMORY_SPLIT_SHIFT_MODE; - dc_lb_memory_split &= - ~(AVIVO_DC_LB_DISP1_END_ADR_MASK << - AVIVO_DC_LB_DISP1_END_ADR_SHIFT); - if (mode1) { - dc_lb_memory_split |= - ((((mode1->hdisplay / 2) + 64) & AVIVO_DC_LB_DISP1_END_ADR_MASK) - << AVIVO_DC_LB_DISP1_END_ADR_SHIFT); - } else if (mode2) { - dc_lb_memory_split |= (0 << AVIVO_DC_LB_DISP1_END_ADR_SHIFT); - } -#endif - WREG32(AVIVO_DC_LB_MEMORY_SPLIT, dc_lb_memory_split); -} diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index 69bd7cb5997..0e00fef0b84 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -1784,3 +1784,486 @@ void r100_clear_surface_reg(struct radeon_device *rdev, int reg) int surf_index = reg * 16; WREG32(RADEON_SURFACE0_INFO + surf_index, 0); } + +void r100_bandwidth_update(struct radeon_device *rdev) +{ + fixed20_12 trcd_ff, trp_ff, tras_ff, trbs_ff, tcas_ff; + fixed20_12 sclk_ff, mclk_ff, sclk_eff_ff, sclk_delay_ff; + fixed20_12 peak_disp_bw, mem_bw, pix_clk, pix_clk2, temp_ff, crit_point_ff; + uint32_t temp, data, mem_trcd, mem_trp, mem_tras; + fixed20_12 memtcas_ff[8] = { + fixed_init(1), + fixed_init(2), + fixed_init(3), + fixed_init(0), + fixed_init_half(1), + fixed_init_half(2), + fixed_init(0), + }; + fixed20_12 memtcas_rs480_ff[8] = { + fixed_init(0), + fixed_init(1), + fixed_init(2), + fixed_init(3), + fixed_init(0), + fixed_init_half(1), + fixed_init_half(2), + fixed_init_half(3), + }; + fixed20_12 memtcas2_ff[8] = { + fixed_init(0), + fixed_init(1), + fixed_init(2), + fixed_init(3), + fixed_init(4), + fixed_init(5), + fixed_init(6), + fixed_init(7), + }; + fixed20_12 memtrbs[8] = { + fixed_init(1), + fixed_init_half(1), + fixed_init(2), + fixed_init_half(2), + fixed_init(3), + fixed_init_half(3), + fixed_init(4), + fixed_init_half(4) + }; + fixed20_12 memtrbs_r4xx[8] = { + fixed_init(4), + fixed_init(5), + fixed_init(6), + fixed_init(7), + fixed_init(8), + fixed_init(9), + fixed_init(10), + fixed_init(11) + }; + fixed20_12 min_mem_eff; + fixed20_12 mc_latency_sclk, mc_latency_mclk, k1; + fixed20_12 cur_latency_mclk, cur_latency_sclk; + fixed20_12 disp_latency, disp_latency_overhead, disp_drain_rate, + disp_drain_rate2, read_return_rate; + fixed20_12 time_disp1_drop_priority; + int c; + int cur_size = 16; /* in octawords */ + int critical_point = 0, critical_point2; +/* uint32_t read_return_rate, time_disp1_drop_priority; */ + int stop_req, max_stop_req; + struct drm_display_mode *mode1 = NULL; + struct drm_display_mode *mode2 = NULL; + uint32_t pixel_bytes1 = 0; + uint32_t pixel_bytes2 = 0; + + if (rdev->mode_info.crtcs[0]->base.enabled) { + mode1 = &rdev->mode_info.crtcs[0]->base.mode; + pixel_bytes1 = rdev->mode_info.crtcs[0]->base.fb->bits_per_pixel / 8; + } + if (rdev->mode_info.crtcs[1]->base.enabled) { + mode2 = &rdev->mode_info.crtcs[1]->base.mode; + pixel_bytes2 = rdev->mode_info.crtcs[1]->base.fb->bits_per_pixel / 8; + } + + min_mem_eff.full = rfixed_const_8(0); + /* get modes */ + if ((rdev->disp_priority == 2) && ASIC_IS_R300(rdev)) { + uint32_t mc_init_misc_lat_timer = RREG32(R300_MC_INIT_MISC_LAT_TIMER); + mc_init_misc_lat_timer &= ~(R300_MC_DISP1R_INIT_LAT_MASK << R300_MC_DISP1R_INIT_LAT_SHIFT); + mc_init_misc_lat_timer &= ~(R300_MC_DISP0R_INIT_LAT_MASK << R300_MC_DISP0R_INIT_LAT_SHIFT); + /* check crtc enables */ + if (mode2) + mc_init_misc_lat_timer |= (1 << R300_MC_DISP1R_INIT_LAT_SHIFT); + if (mode1) + mc_init_misc_lat_timer |= (1 << R300_MC_DISP0R_INIT_LAT_SHIFT); + WREG32(R300_MC_INIT_MISC_LAT_TIMER, mc_init_misc_lat_timer); + } + + /* + * determine is there is enough bw for current mode + */ + mclk_ff.full = rfixed_const(rdev->clock.default_mclk); + temp_ff.full = rfixed_const(100); + mclk_ff.full = rfixed_div(mclk_ff, temp_ff); + sclk_ff.full = rfixed_const(rdev->clock.default_sclk); + sclk_ff.full = rfixed_div(sclk_ff, temp_ff); + + temp = (rdev->mc.vram_width / 8) * (rdev->mc.vram_is_ddr ? 2 : 1); + temp_ff.full = rfixed_const(temp); + mem_bw.full = rfixed_mul(mclk_ff, temp_ff); + + pix_clk.full = 0; + pix_clk2.full = 0; + peak_disp_bw.full = 0; + if (mode1) { + temp_ff.full = rfixed_const(1000); + pix_clk.full = rfixed_const(mode1->clock); /* convert to fixed point */ + pix_clk.full = rfixed_div(pix_clk, temp_ff); + temp_ff.full = rfixed_const(pixel_bytes1); + peak_disp_bw.full += rfixed_mul(pix_clk, temp_ff); + } + if (mode2) { + temp_ff.full = rfixed_const(1000); + pix_clk2.full = rfixed_const(mode2->clock); /* convert to fixed point */ + pix_clk2.full = rfixed_div(pix_clk2, temp_ff); + temp_ff.full = rfixed_const(pixel_bytes2); + peak_disp_bw.full += rfixed_mul(pix_clk2, temp_ff); + } + + mem_bw.full = rfixed_mul(mem_bw, min_mem_eff); + if (peak_disp_bw.full >= mem_bw.full) { + DRM_ERROR("You may not have enough display bandwidth for current mode\n" + "If you have flickering problem, try to lower resolution, refresh rate, or color depth\n"); + } + + /* Get values from the EXT_MEM_CNTL register...converting its contents. */ + temp = RREG32(RADEON_MEM_TIMING_CNTL); + if ((rdev->family == CHIP_RV100) || (rdev->flags & RADEON_IS_IGP)) { /* RV100, M6, IGPs */ + mem_trcd = ((temp >> 2) & 0x3) + 1; + mem_trp = ((temp & 0x3)) + 1; + mem_tras = ((temp & 0x70) >> 4) + 1; + } else if (rdev->family == CHIP_R300 || + rdev->family == CHIP_R350) { /* r300, r350 */ + mem_trcd = (temp & 0x7) + 1; + mem_trp = ((temp >> 8) & 0x7) + 1; + mem_tras = ((temp >> 11) & 0xf) + 4; + } else if (rdev->family == CHIP_RV350 || + rdev->family <= CHIP_RV380) { + /* rv3x0 */ + mem_trcd = (temp & 0x7) + 3; + mem_trp = ((temp >> 8) & 0x7) + 3; + mem_tras = ((temp >> 11) & 0xf) + 6; + } else if (rdev->family == CHIP_R420 || + rdev->family == CHIP_R423 || + rdev->family == CHIP_RV410) { + /* r4xx */ + mem_trcd = (temp & 0xf) + 3; + if (mem_trcd > 15) + mem_trcd = 15; + mem_trp = ((temp >> 8) & 0xf) + 3; + if (mem_trp > 15) + mem_trp = 15; + mem_tras = ((temp >> 12) & 0x1f) + 6; + if (mem_tras > 31) + mem_tras = 31; + } else { /* RV200, R200 */ + mem_trcd = (temp & 0x7) + 1; + mem_trp = ((temp >> 8) & 0x7) + 1; + mem_tras = ((temp >> 12) & 0xf) + 4; + } + /* convert to FF */ + trcd_ff.full = rfixed_const(mem_trcd); + trp_ff.full = rfixed_const(mem_trp); + tras_ff.full = rfixed_const(mem_tras); + + /* Get values from the MEM_SDRAM_MODE_REG register...converting its */ + temp = RREG32(RADEON_MEM_SDRAM_MODE_REG); + data = (temp & (7 << 20)) >> 20; + if ((rdev->family == CHIP_RV100) || rdev->flags & RADEON_IS_IGP) { + if (rdev->family == CHIP_RS480) /* don't think rs400 */ + tcas_ff = memtcas_rs480_ff[data]; + else + tcas_ff = memtcas_ff[data]; + } else + tcas_ff = memtcas2_ff[data]; + + if (rdev->family == CHIP_RS400 || + rdev->family == CHIP_RS480) { + /* extra cas latency stored in bits 23-25 0-4 clocks */ + data = (temp >> 23) & 0x7; + if (data < 5) + tcas_ff.full += rfixed_const(data); + } + + if (ASIC_IS_R300(rdev) && !(rdev->flags & RADEON_IS_IGP)) { + /* on the R300, Tcas is included in Trbs. + */ + temp = RREG32(RADEON_MEM_CNTL); + data = (R300_MEM_NUM_CHANNELS_MASK & temp); + if (data == 1) { + if (R300_MEM_USE_CD_CH_ONLY & temp) { + temp = RREG32(R300_MC_IND_INDEX); + temp &= ~R300_MC_IND_ADDR_MASK; + temp |= R300_MC_READ_CNTL_CD_mcind; + WREG32(R300_MC_IND_INDEX, temp); + temp = RREG32(R300_MC_IND_DATA); + data = (R300_MEM_RBS_POSITION_C_MASK & temp); + } else { + temp = RREG32(R300_MC_READ_CNTL_AB); + data = (R300_MEM_RBS_POSITION_A_MASK & temp); + } + } else { + temp = RREG32(R300_MC_READ_CNTL_AB); + data = (R300_MEM_RBS_POSITION_A_MASK & temp); + } + if (rdev->family == CHIP_RV410 || + rdev->family == CHIP_R420 || + rdev->family == CHIP_R423) + trbs_ff = memtrbs_r4xx[data]; + else + trbs_ff = memtrbs[data]; + tcas_ff.full += trbs_ff.full; + } + + sclk_eff_ff.full = sclk_ff.full; + + if (rdev->flags & RADEON_IS_AGP) { + fixed20_12 agpmode_ff; + agpmode_ff.full = rfixed_const(radeon_agpmode); + temp_ff.full = rfixed_const_666(16); + sclk_eff_ff.full -= rfixed_mul(agpmode_ff, temp_ff); + } + /* TODO PCIE lanes may affect this - agpmode == 16?? */ + + if (ASIC_IS_R300(rdev)) { + sclk_delay_ff.full = rfixed_const(250); + } else { + if ((rdev->family == CHIP_RV100) || + rdev->flags & RADEON_IS_IGP) { + if (rdev->mc.vram_is_ddr) + sclk_delay_ff.full = rfixed_const(41); + else + sclk_delay_ff.full = rfixed_const(33); + } else { + if (rdev->mc.vram_width == 128) + sclk_delay_ff.full = rfixed_const(57); + else + sclk_delay_ff.full = rfixed_const(41); + } + } + + mc_latency_sclk.full = rfixed_div(sclk_delay_ff, sclk_eff_ff); + + if (rdev->mc.vram_is_ddr) { + if (rdev->mc.vram_width == 32) { + k1.full = rfixed_const(40); + c = 3; + } else { + k1.full = rfixed_const(20); + c = 1; + } + } else { + k1.full = rfixed_const(40); + c = 3; + } + + temp_ff.full = rfixed_const(2); + mc_latency_mclk.full = rfixed_mul(trcd_ff, temp_ff); + temp_ff.full = rfixed_const(c); + mc_latency_mclk.full += rfixed_mul(tcas_ff, temp_ff); + temp_ff.full = rfixed_const(4); + mc_latency_mclk.full += rfixed_mul(tras_ff, temp_ff); + mc_latency_mclk.full += rfixed_mul(trp_ff, temp_ff); + mc_latency_mclk.full += k1.full; + + mc_latency_mclk.full = rfixed_div(mc_latency_mclk, mclk_ff); + mc_latency_mclk.full += rfixed_div(temp_ff, sclk_eff_ff); + + /* + HW cursor time assuming worst case of full size colour cursor. + */ + temp_ff.full = rfixed_const((2 * (cur_size - (rdev->mc.vram_is_ddr + 1)))); + temp_ff.full += trcd_ff.full; + if (temp_ff.full < tras_ff.full) + temp_ff.full = tras_ff.full; + cur_latency_mclk.full = rfixed_div(temp_ff, mclk_ff); + + temp_ff.full = rfixed_const(cur_size); + cur_latency_sclk.full = rfixed_div(temp_ff, sclk_eff_ff); + /* + Find the total latency for the display data. + */ + disp_latency_overhead.full = rfixed_const(80); + disp_latency_overhead.full = rfixed_div(disp_latency_overhead, sclk_ff); + mc_latency_mclk.full += disp_latency_overhead.full + cur_latency_mclk.full; + mc_latency_sclk.full += disp_latency_overhead.full + cur_latency_sclk.full; + + if (mc_latency_mclk.full > mc_latency_sclk.full) + disp_latency.full = mc_latency_mclk.full; + else + disp_latency.full = mc_latency_sclk.full; + + /* setup Max GRPH_STOP_REQ default value */ + if (ASIC_IS_RV100(rdev)) + max_stop_req = 0x5c; + else + max_stop_req = 0x7c; + + if (mode1) { + /* CRTC1 + Set GRPH_BUFFER_CNTL register using h/w defined optimal values. + GRPH_STOP_REQ <= MIN[ 0x7C, (CRTC_H_DISP + 1) * (bit depth) / 0x10 ] + */ + stop_req = mode1->hdisplay * pixel_bytes1 / 16; + + if (stop_req > max_stop_req) + stop_req = max_stop_req; + + /* + Find the drain rate of the display buffer. + */ + temp_ff.full = rfixed_const((16/pixel_bytes1)); + disp_drain_rate.full = rfixed_div(pix_clk, temp_ff); + + /* + Find the critical point of the display buffer. + */ + crit_point_ff.full = rfixed_mul(disp_drain_rate, disp_latency); + crit_point_ff.full += rfixed_const_half(0); + + critical_point = rfixed_trunc(crit_point_ff); + + if (rdev->disp_priority == 2) { + critical_point = 0; + } + + /* + The critical point should never be above max_stop_req-4. Setting + GRPH_CRITICAL_CNTL = 0 will thus force high priority all the time. + */ + if (max_stop_req - critical_point < 4) + critical_point = 0; + + if (critical_point == 0 && mode2 && rdev->family == CHIP_R300) { + /* some R300 cards have problem with this set to 0, when CRTC2 is enabled.*/ + critical_point = 0x10; + } + + temp = RREG32(RADEON_GRPH_BUFFER_CNTL); + temp &= ~(RADEON_GRPH_STOP_REQ_MASK); + temp |= (stop_req << RADEON_GRPH_STOP_REQ_SHIFT); + temp &= ~(RADEON_GRPH_START_REQ_MASK); + if ((rdev->family == CHIP_R350) && + (stop_req > 0x15)) { + stop_req -= 0x10; + } + temp |= (stop_req << RADEON_GRPH_START_REQ_SHIFT); + temp |= RADEON_GRPH_BUFFER_SIZE; + temp &= ~(RADEON_GRPH_CRITICAL_CNTL | + RADEON_GRPH_CRITICAL_AT_SOF | + RADEON_GRPH_STOP_CNTL); + /* + Write the result into the register. + */ + WREG32(RADEON_GRPH_BUFFER_CNTL, ((temp & ~RADEON_GRPH_CRITICAL_POINT_MASK) | + (critical_point << RADEON_GRPH_CRITICAL_POINT_SHIFT))); + +#if 0 + if ((rdev->family == CHIP_RS400) || + (rdev->family == CHIP_RS480)) { + /* attempt to program RS400 disp regs correctly ??? */ + temp = RREG32(RS400_DISP1_REG_CNTL); + temp &= ~(RS400_DISP1_START_REQ_LEVEL_MASK | + RS400_DISP1_STOP_REQ_LEVEL_MASK); + WREG32(RS400_DISP1_REQ_CNTL1, (temp | + (critical_point << RS400_DISP1_START_REQ_LEVEL_SHIFT) | + (critical_point << RS400_DISP1_STOP_REQ_LEVEL_SHIFT))); + temp = RREG32(RS400_DMIF_MEM_CNTL1); + temp &= ~(RS400_DISP1_CRITICAL_POINT_START_MASK | + RS400_DISP1_CRITICAL_POINT_STOP_MASK); + WREG32(RS400_DMIF_MEM_CNTL1, (temp | + (critical_point << RS400_DISP1_CRITICAL_POINT_START_SHIFT) | + (critical_point << RS400_DISP1_CRITICAL_POINT_STOP_SHIFT))); + } +#endif + + DRM_DEBUG("GRPH_BUFFER_CNTL from to %x\n", + /* (unsigned int)info->SavedReg->grph_buffer_cntl, */ + (unsigned int)RREG32(RADEON_GRPH_BUFFER_CNTL)); + } + + if (mode2) { + u32 grph2_cntl; + stop_req = mode2->hdisplay * pixel_bytes2 / 16; + + if (stop_req > max_stop_req) + stop_req = max_stop_req; + + /* + Find the drain rate of the display buffer. + */ + temp_ff.full = rfixed_const((16/pixel_bytes2)); + disp_drain_rate2.full = rfixed_div(pix_clk2, temp_ff); + + grph2_cntl = RREG32(RADEON_GRPH2_BUFFER_CNTL); + grph2_cntl &= ~(RADEON_GRPH_STOP_REQ_MASK); + grph2_cntl |= (stop_req << RADEON_GRPH_STOP_REQ_SHIFT); + grph2_cntl &= ~(RADEON_GRPH_START_REQ_MASK); + if ((rdev->family == CHIP_R350) && + (stop_req > 0x15)) { + stop_req -= 0x10; + } + grph2_cntl |= (stop_req << RADEON_GRPH_START_REQ_SHIFT); + grph2_cntl |= RADEON_GRPH_BUFFER_SIZE; + grph2_cntl &= ~(RADEON_GRPH_CRITICAL_CNTL | + RADEON_GRPH_CRITICAL_AT_SOF | + RADEON_GRPH_STOP_CNTL); + + if ((rdev->family == CHIP_RS100) || + (rdev->family == CHIP_RS200)) + critical_point2 = 0; + else { + temp = (rdev->mc.vram_width * rdev->mc.vram_is_ddr + 1)/128; + temp_ff.full = rfixed_const(temp); + temp_ff.full = rfixed_mul(mclk_ff, temp_ff); + if (sclk_ff.full < temp_ff.full) + temp_ff.full = sclk_ff.full; + + read_return_rate.full = temp_ff.full; + + if (mode1) { + temp_ff.full = read_return_rate.full - disp_drain_rate.full; + time_disp1_drop_priority.full = rfixed_div(crit_point_ff, temp_ff); + } else { + time_disp1_drop_priority.full = 0; + } + crit_point_ff.full = disp_latency.full + time_disp1_drop_priority.full + disp_latency.full; + crit_point_ff.full = rfixed_mul(crit_point_ff, disp_drain_rate2); + crit_point_ff.full += rfixed_const_half(0); + + critical_point2 = rfixed_trunc(crit_point_ff); + + if (rdev->disp_priority == 2) { + critical_point2 = 0; + } + + if (max_stop_req - critical_point2 < 4) + critical_point2 = 0; + + } + + if (critical_point2 == 0 && rdev->family == CHIP_R300) { + /* some R300 cards have problem with this set to 0 */ + critical_point2 = 0x10; + } + + WREG32(RADEON_GRPH2_BUFFER_CNTL, ((grph2_cntl & ~RADEON_GRPH_CRITICAL_POINT_MASK) | + (critical_point2 << RADEON_GRPH_CRITICAL_POINT_SHIFT))); + + if ((rdev->family == CHIP_RS400) || + (rdev->family == CHIP_RS480)) { +#if 0 + /* attempt to program RS400 disp2 regs correctly ??? */ + temp = RREG32(RS400_DISP2_REQ_CNTL1); + temp &= ~(RS400_DISP2_START_REQ_LEVEL_MASK | + RS400_DISP2_STOP_REQ_LEVEL_MASK); + WREG32(RS400_DISP2_REQ_CNTL1, (temp | + (critical_point2 << RS400_DISP1_START_REQ_LEVEL_SHIFT) | + (critical_point2 << RS400_DISP1_STOP_REQ_LEVEL_SHIFT))); + temp = RREG32(RS400_DISP2_REQ_CNTL2); + temp &= ~(RS400_DISP2_CRITICAL_POINT_START_MASK | + RS400_DISP2_CRITICAL_POINT_STOP_MASK); + WREG32(RS400_DISP2_REQ_CNTL2, (temp | + (critical_point2 << RS400_DISP2_CRITICAL_POINT_START_SHIFT) | + (critical_point2 << RS400_DISP2_CRITICAL_POINT_STOP_SHIFT))); +#endif + WREG32(RS400_DISP2_REQ_CNTL1, 0x105DC1CC); + WREG32(RS400_DISP2_REQ_CNTL2, 0x2749D000); + WREG32(RS400_DMIF_MEM_CNTL1, 0x29CA71DC); + WREG32(RS400_DISP1_REQ_CNTL1, 0x28FBC3AC); + } + + DRM_DEBUG("GRPH2_BUFFER_CNTL from to %x\n", + (unsigned int)RREG32(RADEON_GRPH2_BUFFER_CNTL)); + } +} diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c index 28e5777658b..9c8d41534a5 100644 --- a/drivers/gpu/drm/radeon/r300.c +++ b/drivers/gpu/drm/radeon/r300.c @@ -31,6 +31,7 @@ #include "radeon_reg.h" #include "radeon.h" #include "radeon_drm.h" +#include "radeon_share.h" /* r300,r350,rv350,rv370,rv380 depends on : */ void r100_hdp_reset(struct radeon_device *rdev); diff --git a/drivers/gpu/drm/radeon/r520.c b/drivers/gpu/drm/radeon/r520.c index b6bd3758db6..0a981e2ee2f 100644 --- a/drivers/gpu/drm/radeon/r520.c +++ b/drivers/gpu/drm/radeon/r520.c @@ -28,6 +28,7 @@ #include "drmP.h" #include "radeon_reg.h" #include "radeon.h" +#include "radeon_share.h" /* r520,rv530,rv560,rv570,r580 depends on : */ void r100_hdp_reset(struct radeon_device *rdev); @@ -226,7 +227,20 @@ static void r520_vram_get_type(struct radeon_device *rdev) void r520_vram_info(struct radeon_device *rdev) { + fixed20_12 a; + r520_vram_get_type(rdev); r100_vram_init_sizes(rdev); + /* FIXME: we should enforce default clock in case GPU is not in + * default setup + */ + a.full = rfixed_const(100); + rdev->pm.sclk.full = rfixed_const(rdev->clock.default_sclk); + rdev->pm.sclk.full = rfixed_div(rdev->pm.sclk, a); +} + +void r520_bandwidth_update(struct radeon_device *rdev) +{ + rv515_bandwidth_avivo_update(rdev); } diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index af12a2fe322..63a3fe32e58 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -113,6 +113,7 @@ enum radeon_family { CHIP_RV770, CHIP_RV730, CHIP_RV710, + CHIP_RS880, CHIP_LAST, }; @@ -490,6 +491,39 @@ struct radeon_wb { uint64_t gpu_addr; }; +/** + * struct radeon_pm - power management datas + * @max_bandwidth: maximum bandwidth the gpu has (MByte/s) + * @igp_sideport_mclk: sideport memory clock Mhz (rs690,rs740,rs780,rs880) + * @igp_system_mclk: system clock Mhz (rs690,rs740,rs780,rs880) + * @igp_ht_link_clk: ht link clock Mhz (rs690,rs740,rs780,rs880) + * @igp_ht_link_width: ht link width in bits (rs690,rs740,rs780,rs880) + * @k8_bandwidth: k8 bandwidth the gpu has (MByte/s) (IGP) + * @sideport_bandwidth: sideport bandwidth the gpu has (MByte/s) (IGP) + * @ht_bandwidth: ht bandwidth the gpu has (MByte/s) (IGP) + * @core_bandwidth: core GPU bandwidth the gpu has (MByte/s) (IGP) + * @sclk: GPU clock Mhz (core bandwith depends of this clock) + * @needed_bandwidth: current bandwidth needs + * + * It keeps track of various data needed to take powermanagement decision. + * Bandwith need is used to determine minimun clock of the GPU and memory. + * Equation between gpu/memory clock and available bandwidth is hw dependent + * (type of memory, bus size, efficiency, ...) + */ +struct radeon_pm { + fixed20_12 max_bandwidth; + fixed20_12 igp_sideport_mclk; + fixed20_12 igp_system_mclk; + fixed20_12 igp_ht_link_clk; + fixed20_12 igp_ht_link_width; + fixed20_12 k8_bandwidth; + fixed20_12 sideport_bandwidth; + fixed20_12 ht_bandwidth; + fixed20_12 core_bandwidth; + fixed20_12 sclk; + fixed20_12 needed_bandwidth; +}; + /* * Benchmarking @@ -551,19 +585,17 @@ struct radeon_asic { void (*set_memory_clock)(struct radeon_device *rdev, uint32_t mem_clock); void (*set_pcie_lanes)(struct radeon_device *rdev, int lanes); void (*set_clock_gating)(struct radeon_device *rdev, int enable); - int (*set_surface_reg)(struct radeon_device *rdev, int reg, uint32_t tiling_flags, uint32_t pitch, uint32_t offset, uint32_t obj_size); int (*clear_surface_reg)(struct radeon_device *rdev, int reg); + void (*bandwidth_update)(struct radeon_device *rdev); }; union radeon_asic_config { struct r300_asic r300; }; -/* r100 */ -void r100_vram_init_sizes(struct radeon_device *rdev); /* * IOCTL. @@ -646,6 +678,7 @@ struct radeon_device { struct radeon_irq irq; struct radeon_asic *asic; struct radeon_gem gem; + struct radeon_pm pm; struct mutex cs_mutex; struct radeon_wb wb; bool gpu_lockup; @@ -829,5 +862,6 @@ static inline void radeon_ring_write(struct radeon_device *rdev, uint32_t v) #define radeon_set_clock_gating(rdev, e) (rdev)->asic->set_clock_gating((rdev), (e)) #define radeon_set_surface_reg(rdev, r, f, p, o, s) ((rdev)->asic->set_surface_reg((rdev), (r), (f), (p), (o), (s))) #define radeon_clear_surface_reg(rdev, r) ((rdev)->asic->clear_surface_reg((rdev), (r))) +#define radeon_bandwidth_update(rdev) (rdev)->asic->bandwidth_update((rdev)) #endif diff --git a/drivers/gpu/drm/radeon/radeon_asic.h b/drivers/gpu/drm/radeon/radeon_asic.h index dd903d32940..9a75876e0c3 100644 --- a/drivers/gpu/drm/radeon/radeon_asic.h +++ b/drivers/gpu/drm/radeon/radeon_asic.h @@ -75,6 +75,7 @@ int r100_set_surface_reg(struct radeon_device *rdev, int reg, uint32_t tiling_flags, uint32_t pitch, uint32_t offset, uint32_t obj_size); int r100_clear_surface_reg(struct radeon_device *rdev, int reg); +void r100_bandwidth_update(struct radeon_device *rdev); static struct radeon_asic r100_asic = { .init = &r100_init, @@ -106,6 +107,7 @@ static struct radeon_asic r100_asic = { .set_clock_gating = &radeon_legacy_set_clock_gating, .set_surface_reg = r100_set_surface_reg, .clear_surface_reg = r100_clear_surface_reg, + .bandwidth_update = &r100_bandwidth_update, }; @@ -165,6 +167,7 @@ static struct radeon_asic r300_asic = { .set_clock_gating = &radeon_legacy_set_clock_gating, .set_surface_reg = r100_set_surface_reg, .clear_surface_reg = r100_clear_surface_reg, + .bandwidth_update = &r100_bandwidth_update, }; /* @@ -204,6 +207,7 @@ static struct radeon_asic r420_asic = { .set_clock_gating = &radeon_atom_set_clock_gating, .set_surface_reg = r100_set_surface_reg, .clear_surface_reg = r100_clear_surface_reg, + .bandwidth_update = &r100_bandwidth_update, }; @@ -250,6 +254,7 @@ static struct radeon_asic rs400_asic = { .set_clock_gating = &radeon_legacy_set_clock_gating, .set_surface_reg = r100_set_surface_reg, .clear_surface_reg = r100_clear_surface_reg, + .bandwidth_update = &r100_bandwidth_update, }; @@ -267,6 +272,7 @@ void rs600_gart_tlb_flush(struct radeon_device *rdev); int rs600_gart_set_page(struct radeon_device *rdev, int i, uint64_t addr); uint32_t rs600_mc_rreg(struct radeon_device *rdev, uint32_t reg); void rs600_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v); +void rs600_bandwidth_update(struct radeon_device *rdev); static struct radeon_asic rs600_asic = { .init = &r300_init, .errata = &rs600_errata, @@ -295,6 +301,7 @@ static struct radeon_asic rs600_asic = { .set_memory_clock = &radeon_atom_set_memory_clock, .set_pcie_lanes = NULL, .set_clock_gating = &radeon_atom_set_clock_gating, + .bandwidth_update = &rs600_bandwidth_update, }; @@ -307,6 +314,7 @@ int rs690_mc_init(struct radeon_device *rdev); void rs690_mc_fini(struct radeon_device *rdev); uint32_t rs690_mc_rreg(struct radeon_device *rdev, uint32_t reg); void rs690_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v); +void rs690_bandwidth_update(struct radeon_device *rdev); static struct radeon_asic rs690_asic = { .init = &r300_init, .errata = &rs690_errata, @@ -337,6 +345,7 @@ static struct radeon_asic rs690_asic = { .set_clock_gating = &radeon_atom_set_clock_gating, .set_surface_reg = r100_set_surface_reg, .clear_surface_reg = r100_clear_surface_reg, + .bandwidth_update = &rs690_bandwidth_update, }; @@ -354,6 +363,7 @@ void rv515_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v); void rv515_ring_start(struct radeon_device *rdev); uint32_t rv515_pcie_rreg(struct radeon_device *rdev, uint32_t reg); void rv515_pcie_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v); +void rv515_bandwidth_update(struct radeon_device *rdev); static struct radeon_asic rv515_asic = { .init = &rv515_init, .errata = &rv515_errata, @@ -384,6 +394,7 @@ static struct radeon_asic rv515_asic = { .set_clock_gating = &radeon_atom_set_clock_gating, .set_surface_reg = r100_set_surface_reg, .clear_surface_reg = r100_clear_surface_reg, + .bandwidth_update = &rv515_bandwidth_update, }; @@ -394,6 +405,7 @@ void r520_errata(struct radeon_device *rdev); void r520_vram_info(struct radeon_device *rdev); int r520_mc_init(struct radeon_device *rdev); void r520_mc_fini(struct radeon_device *rdev); +void r520_bandwidth_update(struct radeon_device *rdev); static struct radeon_asic r520_asic = { .init = &rv515_init, .errata = &r520_errata, @@ -424,6 +436,7 @@ static struct radeon_asic r520_asic = { .set_clock_gating = &radeon_atom_set_clock_gating, .set_surface_reg = r100_set_surface_reg, .clear_surface_reg = r100_clear_surface_reg, + .bandwidth_update = &r520_bandwidth_update, }; /* diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c index f23083bbba3..f78db5c8008 100644 --- a/drivers/gpu/drm/radeon/radeon_device.c +++ b/drivers/gpu/drm/radeon/radeon_device.c @@ -561,6 +561,11 @@ int radeon_device_init(struct radeon_device *rdev, radeon_combios_asic_init(rdev->ddev); } } + /* Initialize clocks */ + r = radeon_clocks_init(rdev); + if (r) { + return r; + } /* Get vram informations */ radeon_vram_info(rdev); @@ -572,11 +577,6 @@ int radeon_device_init(struct radeon_device *rdev, (unsigned)rdev->mc.aper_size >> 20); DRM_INFO("RAM width %dbits %cDR\n", rdev->mc.vram_width, rdev->mc.vram_is_ddr ? 'D' : 'S'); - /* Initialize clocks */ - r = radeon_clocks_init(rdev); - if (r) { - return r; - } /* Initialize memory controller (also test AGP) */ r = radeon_mc_init(rdev); if (r) { diff --git a/drivers/gpu/drm/radeon/radeon_display.c b/drivers/gpu/drm/radeon/radeon_display.c index bc312f3d9a0..a8fa1bb84cf 100644 --- a/drivers/gpu/drm/radeon/radeon_display.c +++ b/drivers/gpu/drm/radeon/radeon_display.c @@ -187,6 +187,7 @@ static void radeon_crtc_init(struct drm_device *dev, int index) drm_mode_crtc_set_gamma_size(&radeon_crtc->base, 256); radeon_crtc->crtc_id = index; + rdev->mode_info.crtcs[index] = radeon_crtc; radeon_crtc->mode_set.crtc = &radeon_crtc->base; radeon_crtc->mode_set.connectors = (struct drm_connector **)(radeon_crtc + 1); @@ -661,36 +662,51 @@ void radeon_modeset_fini(struct radeon_device *rdev) } } -void radeon_init_disp_bandwidth(struct drm_device *dev) +bool radeon_crtc_scaling_mode_fixup(struct drm_crtc *crtc, + struct drm_display_mode *mode, + struct drm_display_mode *adjusted_mode) { - struct radeon_device *rdev = dev->dev_private; - struct drm_display_mode *modes[2]; - int pixel_bytes[2]; - struct drm_crtc *crtc; - - pixel_bytes[0] = pixel_bytes[1] = 0; - modes[0] = modes[1] = NULL; - - list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) { - struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc); + struct drm_device *dev = crtc->dev; + struct drm_encoder *encoder; + struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc); + struct radeon_encoder *radeon_encoder; + bool first = true; - if (crtc->enabled && crtc->fb) { - modes[radeon_crtc->crtc_id] = &crtc->mode; - pixel_bytes[radeon_crtc->crtc_id] = crtc->fb->bits_per_pixel / 8; + list_for_each_entry(encoder, &dev->mode_config.encoder_list, head) { + radeon_encoder = to_radeon_encoder(encoder); + if (encoder->crtc != crtc) + continue; + if (first) { + radeon_crtc->rmx_type = radeon_encoder->rmx_type; + radeon_crtc->devices = radeon_encoder->devices; + memcpy(&radeon_crtc->native_mode, + &radeon_encoder->native_mode, + sizeof(struct radeon_native_mode)); + first = false; + } else { + if (radeon_crtc->rmx_type != radeon_encoder->rmx_type) { + /* WARNING: Right now this can't happen but + * in the future we need to check that scaling + * are consistent accross different encoder + * (ie all encoder can work with the same + * scaling). + */ + DRM_ERROR("Scaling not consistent accross encoder.\n"); + return false; + } } } - - if (ASIC_IS_AVIVO(rdev)) { - radeon_init_disp_bw_avivo(dev, - modes[0], - pixel_bytes[0], - modes[1], - pixel_bytes[1]); + if (radeon_crtc->rmx_type != RMX_OFF) { + fixed20_12 a, b; + a.full = rfixed_const(crtc->mode.vdisplay); + b.full = rfixed_const(radeon_crtc->native_mode.panel_xres); + radeon_crtc->vsc.full = rfixed_div(a, b); + a.full = rfixed_const(crtc->mode.hdisplay); + b.full = rfixed_const(radeon_crtc->native_mode.panel_yres); + radeon_crtc->hsc.full = rfixed_div(a, b); } else { - radeon_init_disp_bw_legacy(dev, - modes[0], - pixel_bytes[0], - modes[1], - pixel_bytes[1]); + radeon_crtc->vsc.full = rfixed_const(1); + radeon_crtc->hsc.full = rfixed_const(1); } + return true; } diff --git a/drivers/gpu/drm/radeon/radeon_encoders.c b/drivers/gpu/drm/radeon/radeon_encoders.c index ea15284e758..0a92706eac1 100644 --- a/drivers/gpu/drm/radeon/radeon_encoders.c +++ b/drivers/gpu/drm/radeon/radeon_encoders.c @@ -154,7 +154,6 @@ void radeon_rmx_mode_fixup(struct drm_encoder *encoder, if (mode->hdisplay < native_mode->panel_xres || mode->vdisplay < native_mode->panel_yres) { - radeon_encoder->flags |= RADEON_USE_RMX; if (ASIC_IS_AVIVO(rdev)) { adjusted_mode->hdisplay = native_mode->panel_xres; adjusted_mode->vdisplay = native_mode->panel_yres; @@ -197,15 +196,13 @@ void radeon_rmx_mode_fixup(struct drm_encoder *encoder, } } + static bool radeon_atom_mode_fixup(struct drm_encoder *encoder, struct drm_display_mode *mode, struct drm_display_mode *adjusted_mode) { - struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder); - radeon_encoder->flags &= ~RADEON_USE_RMX; - drm_mode_set_crtcinfo(adjusted_mode, 0); if (radeon_encoder->rmx_type != RMX_OFF) @@ -808,234 +805,6 @@ atombios_dig_transmitter_setup(struct drm_encoder *encoder, int action) } -static void atom_rv515_force_tv_scaler(struct radeon_device *rdev) -{ - - WREG32(0x659C, 0x0); - WREG32(0x6594, 0x705); - WREG32(0x65A4, 0x10001); - WREG32(0x65D8, 0x0); - WREG32(0x65B0, 0x0); - WREG32(0x65C0, 0x0); - WREG32(0x65D4, 0x0); - WREG32(0x6578, 0x0); - WREG32(0x657C, 0x841880A8); - WREG32(0x6578, 0x1); - WREG32(0x657C, 0x84208680); - WREG32(0x6578, 0x2); - WREG32(0x657C, 0xBFF880B0); - WREG32(0x6578, 0x100); - WREG32(0x657C, 0x83D88088); - WREG32(0x6578, 0x101); - WREG32(0x657C, 0x84608680); - WREG32(0x6578, 0x102); - WREG32(0x657C, 0xBFF080D0); - WREG32(0x6578, 0x200); - WREG32(0x657C, 0x83988068); - WREG32(0x6578, 0x201); - WREG32(0x657C, 0x84A08680); - WREG32(0x6578, 0x202); - WREG32(0x657C, 0xBFF080F8); - WREG32(0x6578, 0x300); - WREG32(0x657C, 0x83588058); - WREG32(0x6578, 0x301); - WREG32(0x657C, 0x84E08660); - WREG32(0x6578, 0x302); - WREG32(0x657C, 0xBFF88120); - WREG32(0x6578, 0x400); - WREG32(0x657C, 0x83188040); - WREG32(0x6578, 0x401); - WREG32(0x657C, 0x85008660); - WREG32(0x6578, 0x402); - WREG32(0x657C, 0xBFF88150); - WREG32(0x6578, 0x500); - WREG32(0x657C, 0x82D88030); - WREG32(0x6578, 0x501); - WREG32(0x657C, 0x85408640); - WREG32(0x6578, 0x502); - WREG32(0x657C, 0xBFF88180); - WREG32(0x6578, 0x600); - WREG32(0x657C, 0x82A08018); - WREG32(0x6578, 0x601); - WREG32(0x657C, 0x85808620); - WREG32(0x6578, 0x602); - WREG32(0x657C, 0xBFF081B8); - WREG32(0x6578, 0x700); - WREG32(0x657C, 0x82608010); - WREG32(0x6578, 0x701); - WREG32(0x657C, 0x85A08600); - WREG32(0x6578, 0x702); - WREG32(0x657C, 0x800081F0); - WREG32(0x6578, 0x800); - WREG32(0x657C, 0x8228BFF8); - WREG32(0x6578, 0x801); - WREG32(0x657C, 0x85E085E0); - WREG32(0x6578, 0x802); - WREG32(0x657C, 0xBFF88228); - WREG32(0x6578, 0x10000); - WREG32(0x657C, 0x82A8BF00); - WREG32(0x6578, 0x10001); - WREG32(0x657C, 0x82A08CC0); - WREG32(0x6578, 0x10002); - WREG32(0x657C, 0x8008BEF8); - WREG32(0x6578, 0x10100); - WREG32(0x657C, 0x81F0BF28); - WREG32(0x6578, 0x10101); - WREG32(0x657C, 0x83608CA0); - WREG32(0x6578, 0x10102); - WREG32(0x657C, 0x8018BED0); - WREG32(0x6578, 0x10200); - WREG32(0x657C, 0x8148BF38); - WREG32(0x6578, 0x10201); - WREG32(0x657C, 0x84408C80); - WREG32(0x6578, 0x10202); - WREG32(0x657C, 0x8008BEB8); - WREG32(0x6578, 0x10300); - WREG32(0x657C, 0x80B0BF78); - WREG32(0x6578, 0x10301); - WREG32(0x657C, 0x85008C20); - WREG32(0x6578, 0x10302); - WREG32(0x657C, 0x8020BEA0); - WREG32(0x6578, 0x10400); - WREG32(0x657C, 0x8028BF90); - WREG32(0x6578, 0x10401); - WREG32(0x657C, 0x85E08BC0); - WREG32(0x6578, 0x10402); - WREG32(0x657C, 0x8018BE90); - WREG32(0x6578, 0x10500); - WREG32(0x657C, 0xBFB8BFB0); - WREG32(0x6578, 0x10501); - WREG32(0x657C, 0x86C08B40); - WREG32(0x6578, 0x10502); - WREG32(0x657C, 0x8010BE90); - WREG32(0x6578, 0x10600); - WREG32(0x657C, 0xBF58BFC8); - WREG32(0x6578, 0x10601); - WREG32(0x657C, 0x87A08AA0); - WREG32(0x6578, 0x10602); - WREG32(0x657C, 0x8010BE98); - WREG32(0x6578, 0x10700); - WREG32(0x657C, 0xBF10BFF0); - WREG32(0x6578, 0x10701); - WREG32(0x657C, 0x886089E0); - WREG32(0x6578, 0x10702); - WREG32(0x657C, 0x8018BEB0); - WREG32(0x6578, 0x10800); - WREG32(0x657C, 0xBED8BFE8); - WREG32(0x6578, 0x10801); - WREG32(0x657C, 0x89408940); - WREG32(0x6578, 0x10802); - WREG32(0x657C, 0xBFE8BED8); - WREG32(0x6578, 0x20000); - WREG32(0x657C, 0x80008000); - WREG32(0x6578, 0x20001); - WREG32(0x657C, 0x90008000); - WREG32(0x6578, 0x20002); - WREG32(0x657C, 0x80008000); - WREG32(0x6578, 0x20003); - WREG32(0x657C, 0x80008000); - WREG32(0x6578, 0x20100); - WREG32(0x657C, 0x80108000); - WREG32(0x6578, 0x20101); - WREG32(0x657C, 0x8FE0BF70); - WREG32(0x6578, 0x20102); - WREG32(0x657C, 0xBFE880C0); - WREG32(0x6578, 0x20103); - WREG32(0x657C, 0x80008000); - WREG32(0x6578, 0x20200); - WREG32(0x657C, 0x8018BFF8); - WREG32(0x6578, 0x20201); - WREG32(0x657C, 0x8F80BF08); - WREG32(0x6578, 0x20202); - WREG32(0x657C, 0xBFD081A0); - WREG32(0x6578, 0x20203); - WREG32(0x657C, 0xBFF88000); - WREG32(0x6578, 0x20300); - WREG32(0x657C, 0x80188000); - WREG32(0x6578, 0x20301); - WREG32(0x657C, 0x8EE0BEC0); - WREG32(0x6578, 0x20302); - WREG32(0x657C, 0xBFB082A0); - WREG32(0x6578, 0x20303); - WREG32(0x657C, 0x80008000); - WREG32(0x6578, 0x20400); - WREG32(0x657C, 0x80188000); - WREG32(0x6578, 0x20401); - WREG32(0x657C, 0x8E00BEA0); - WREG32(0x6578, 0x20402); - WREG32(0x657C, 0xBF8883C0); - WREG32(0x6578, 0x20403); - WREG32(0x657C, 0x80008000); - WREG32(0x6578, 0x20500); - WREG32(0x657C, 0x80188000); - WREG32(0x6578, 0x20501); - WREG32(0x657C, 0x8D00BE90); - WREG32(0x6578, 0x20502); - WREG32(0x657C, 0xBF588500); - WREG32(0x6578, 0x20503); - WREG32(0x657C, 0x80008008); - WREG32(0x6578, 0x20600); - WREG32(0x657C, 0x80188000); - WREG32(0x6578, 0x20601); - WREG32(0x657C, 0x8BC0BE98); - WREG32(0x6578, 0x20602); - WREG32(0x657C, 0xBF308660); - WREG32(0x6578, 0x20603); - WREG32(0x657C, 0x80008008); - WREG32(0x6578, 0x20700); - WREG32(0x657C, 0x80108000); - WREG32(0x6578, 0x20701); - WREG32(0x657C, 0x8A80BEB0); - WREG32(0x6578, 0x20702); - WREG32(0x657C, 0xBF0087C0); - WREG32(0x6578, 0x20703); - WREG32(0x657C, 0x80008008); - WREG32(0x6578, 0x20800); - WREG32(0x657C, 0x80108000); - WREG32(0x6578, 0x20801); - WREG32(0x657C, 0x8920BED0); - WREG32(0x6578, 0x20802); - WREG32(0x657C, 0xBED08920); - WREG32(0x6578, 0x20803); - WREG32(0x657C, 0x80008010); - WREG32(0x6578, 0x30000); - WREG32(0x657C, 0x90008000); - WREG32(0x6578, 0x30001); - WREG32(0x657C, 0x80008000); - WREG32(0x6578, 0x30100); - WREG32(0x657C, 0x8FE0BF90); - WREG32(0x6578, 0x30101); - WREG32(0x657C, 0xBFF880A0); - WREG32(0x6578, 0x30200); - WREG32(0x657C, 0x8F60BF40); - WREG32(0x6578, 0x30201); - WREG32(0x657C, 0xBFE88180); - WREG32(0x6578, 0x30300); - WREG32(0x657C, 0x8EC0BF00); - WREG32(0x6578, 0x30301); - WREG32(0x657C, 0xBFC88280); - WREG32(0x6578, 0x30400); - WREG32(0x657C, 0x8DE0BEE0); - WREG32(0x6578, 0x30401); - WREG32(0x657C, 0xBFA083A0); - WREG32(0x6578, 0x30500); - WREG32(0x657C, 0x8CE0BED0); - WREG32(0x6578, 0x30501); - WREG32(0x657C, 0xBF7884E0); - WREG32(0x6578, 0x30600); - WREG32(0x657C, 0x8BA0BED8); - WREG32(0x6578, 0x30601); - WREG32(0x657C, 0xBF508640); - WREG32(0x6578, 0x30700); - WREG32(0x657C, 0x8A60BEE8); - WREG32(0x6578, 0x30701); - WREG32(0x657C, 0xBF2087A0); - WREG32(0x6578, 0x30800); - WREG32(0x657C, 0x8900BF00); - WREG32(0x6578, 0x30801); - WREG32(0x657C, 0xBF008900); -} - static void atombios_yuv_setup(struct drm_encoder *encoder, bool enable) { @@ -1073,129 +842,6 @@ atombios_yuv_setup(struct drm_encoder *encoder, bool enable) WREG32(reg, temp); } -static void -atombios_overscan_setup(struct drm_encoder *encoder, - struct drm_display_mode *mode, - struct drm_display_mode *adjusted_mode) -{ - struct drm_device *dev = encoder->dev; - struct radeon_device *rdev = dev->dev_private; - struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder); - struct radeon_crtc *radeon_crtc = to_radeon_crtc(encoder->crtc); - SET_CRTC_OVERSCAN_PS_ALLOCATION args; - int index = GetIndexIntoMasterTable(COMMAND, SetCRTC_OverScan); - - memset(&args, 0, sizeof(args)); - - args.usOverscanRight = 0; - args.usOverscanLeft = 0; - args.usOverscanBottom = 0; - args.usOverscanTop = 0; - args.ucCRTC = radeon_crtc->crtc_id; - - if (radeon_encoder->flags & RADEON_USE_RMX) { - if (radeon_encoder->rmx_type == RMX_FULL) { - args.usOverscanRight = 0; - args.usOverscanLeft = 0; - args.usOverscanBottom = 0; - args.usOverscanTop = 0; - } else if (radeon_encoder->rmx_type == RMX_CENTER) { - args.usOverscanTop = (adjusted_mode->crtc_vdisplay - mode->crtc_vdisplay) / 2; - args.usOverscanBottom = (adjusted_mode->crtc_vdisplay - mode->crtc_vdisplay) / 2; - args.usOverscanLeft = (adjusted_mode->crtc_hdisplay - mode->crtc_hdisplay) / 2; - args.usOverscanRight = (adjusted_mode->crtc_hdisplay - mode->crtc_hdisplay) / 2; - } else if (radeon_encoder->rmx_type == RMX_ASPECT) { - int a1 = mode->crtc_vdisplay * adjusted_mode->crtc_hdisplay; - int a2 = adjusted_mode->crtc_vdisplay * mode->crtc_hdisplay; - - if (a1 > a2) { - args.usOverscanLeft = (adjusted_mode->crtc_hdisplay - (a2 / mode->crtc_vdisplay)) / 2; - args.usOverscanRight = (adjusted_mode->crtc_hdisplay - (a2 / mode->crtc_vdisplay)) / 2; - } else if (a2 > a1) { - args.usOverscanLeft = (adjusted_mode->crtc_vdisplay - (a1 / mode->crtc_hdisplay)) / 2; - args.usOverscanRight = (adjusted_mode->crtc_vdisplay - (a1 / mode->crtc_hdisplay)) / 2; - } - } - } - - atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args); - -} - -static void -atombios_scaler_setup(struct drm_encoder *encoder) -{ - struct drm_device *dev = encoder->dev; - struct radeon_device *rdev = dev->dev_private; - struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder); - struct radeon_crtc *radeon_crtc = to_radeon_crtc(encoder->crtc); - ENABLE_SCALER_PS_ALLOCATION args; - int index = GetIndexIntoMasterTable(COMMAND, EnableScaler); - /* fixme - fill in enc_priv for atom dac */ - enum radeon_tv_std tv_std = TV_STD_NTSC; - - if (!ASIC_IS_AVIVO(rdev) && radeon_crtc->crtc_id) - return; - - memset(&args, 0, sizeof(args)); - - args.ucScaler = radeon_crtc->crtc_id; - - if (radeon_encoder->devices & (ATOM_DEVICE_TV_SUPPORT)) { - switch (tv_std) { - case TV_STD_NTSC: - default: - args.ucTVStandard = ATOM_TV_NTSC; - break; - case TV_STD_PAL: - args.ucTVStandard = ATOM_TV_PAL; - break; - case TV_STD_PAL_M: - args.ucTVStandard = ATOM_TV_PALM; - break; - case TV_STD_PAL_60: - args.ucTVStandard = ATOM_TV_PAL60; - break; - case TV_STD_NTSC_J: - args.ucTVStandard = ATOM_TV_NTSCJ; - break; - case TV_STD_SCART_PAL: - args.ucTVStandard = ATOM_TV_PAL; /* ??? */ - break; - case TV_STD_SECAM: - args.ucTVStandard = ATOM_TV_SECAM; - break; - case TV_STD_PAL_CN: - args.ucTVStandard = ATOM_TV_PALCN; - break; - } - args.ucEnable = SCALER_ENABLE_MULTITAP_MODE; - } else if (radeon_encoder->devices & (ATOM_DEVICE_CV_SUPPORT)) { - args.ucTVStandard = ATOM_TV_CV; - args.ucEnable = SCALER_ENABLE_MULTITAP_MODE; - } else if (radeon_encoder->flags & RADEON_USE_RMX) { - if (radeon_encoder->rmx_type == RMX_FULL) - args.ucEnable = ATOM_SCALER_EXPANSION; - else if (radeon_encoder->rmx_type == RMX_CENTER) - args.ucEnable = ATOM_SCALER_CENTER; - else if (radeon_encoder->rmx_type == RMX_ASPECT) - args.ucEnable = ATOM_SCALER_EXPANSION; - } else { - if (ASIC_IS_AVIVO(rdev)) - args.ucEnable = ATOM_SCALER_DISABLE; - else - args.ucEnable = ATOM_SCALER_CENTER; - } - - atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args); - - if (radeon_encoder->devices & (ATOM_DEVICE_CV_SUPPORT | ATOM_DEVICE_TV_SUPPORT) - && rdev->family >= CHIP_RV515 && rdev->family <= CHIP_RV570) { - atom_rv515_force_tv_scaler(rdev); - } - -} - static void radeon_atom_encoder_dpms(struct drm_encoder *encoder, int mode) { @@ -1448,8 +1094,6 @@ radeon_atom_encoder_mode_set(struct drm_encoder *encoder, radeon_encoder->pixel_clock = adjusted_mode->clock; radeon_atombios_encoder_crtc_scratch_regs(encoder, radeon_crtc->crtc_id); - atombios_overscan_setup(encoder, mode, adjusted_mode); - atombios_scaler_setup(encoder); atombios_set_encoder_crtc_source(encoder); if (ASIC_IS_AVIVO(rdev)) { @@ -1667,6 +1311,7 @@ radeon_add_atom_encoder(struct drm_device *dev, uint32_t encoder_id, uint32_t su radeon_encoder->encoder_id = encoder_id; radeon_encoder->devices = supported_device; + radeon_encoder->rmx_type = RMX_OFF; switch (radeon_encoder->encoder_id) { case ENCODER_OBJECT_ID_INTERNAL_LVDS: @@ -1700,14 +1345,8 @@ radeon_add_atom_encoder(struct drm_device *dev, uint32_t encoder_id, uint32_t su case ENCODER_OBJECT_ID_INTERNAL_KLDSCP_LVTMA: case ENCODER_OBJECT_ID_INTERNAL_UNIPHY1: case ENCODER_OBJECT_ID_INTERNAL_UNIPHY2: - if (radeon_encoder->devices & (ATOM_DEVICE_LCD_SUPPORT)) { - radeon_encoder->rmx_type = RMX_FULL; - drm_encoder_init(dev, encoder, &radeon_atom_enc_funcs, DRM_MODE_ENCODER_LVDS); - radeon_encoder->enc_priv = radeon_atombios_get_lvds_info(radeon_encoder); - } else { - drm_encoder_init(dev, encoder, &radeon_atom_enc_funcs, DRM_MODE_ENCODER_TMDS); - radeon_encoder->enc_priv = radeon_atombios_set_dig_info(radeon_encoder); - } + drm_encoder_init(dev, encoder, &radeon_atom_enc_funcs, DRM_MODE_ENCODER_TMDS); + radeon_encoder->enc_priv = radeon_atombios_set_dig_info(radeon_encoder); drm_encoder_helper_add(encoder, &radeon_atom_dig_helper_funcs); break; } diff --git a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c index 0613790e2a5..7d06dc98a42 100644 --- a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c +++ b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c @@ -29,6 +29,171 @@ #include "radeon_fixed.h" #include "radeon.h" +static void radeon_legacy_rmx_mode_set(struct drm_crtc *crtc, + struct drm_display_mode *mode, + struct drm_display_mode *adjusted_mode) +{ + struct drm_device *dev = crtc->dev; + struct radeon_device *rdev = dev->dev_private; + struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc); + int xres = mode->hdisplay; + int yres = mode->vdisplay; + bool hscale = true, vscale = true; + int hsync_wid; + int vsync_wid; + int hsync_start; + int blank_width; + u32 scale, inc, crtc_more_cntl; + u32 fp_horz_stretch, fp_vert_stretch, fp_horz_vert_active; + u32 fp_h_sync_strt_wid, fp_crtc_h_total_disp; + u32 fp_v_sync_strt_wid, fp_crtc_v_total_disp; + struct radeon_native_mode *native_mode = &radeon_crtc->native_mode; + + fp_vert_stretch = RREG32(RADEON_FP_VERT_STRETCH) & + (RADEON_VERT_STRETCH_RESERVED | + RADEON_VERT_AUTO_RATIO_INC); + fp_horz_stretch = RREG32(RADEON_FP_HORZ_STRETCH) & + (RADEON_HORZ_FP_LOOP_STRETCH | + RADEON_HORZ_AUTO_RATIO_INC); + + crtc_more_cntl = 0; + if ((rdev->family == CHIP_RS100) || + (rdev->family == CHIP_RS200)) { + /* This is to workaround the asic bug for RMX, some versions + of BIOS dosen't have this register initialized correctly. */ + crtc_more_cntl |= RADEON_CRTC_H_CUTOFF_ACTIVE_EN; + } + + + fp_crtc_h_total_disp = ((((mode->crtc_htotal / 8) - 1) & 0x3ff) + | ((((mode->crtc_hdisplay / 8) - 1) & 0x1ff) << 16)); + + hsync_wid = (mode->crtc_hsync_end - mode->crtc_hsync_start) / 8; + if (!hsync_wid) + hsync_wid = 1; + hsync_start = mode->crtc_hsync_start - 8; + + fp_h_sync_strt_wid = ((hsync_start & 0x1fff) + | ((hsync_wid & 0x3f) << 16) + | ((mode->flags & DRM_MODE_FLAG_NHSYNC) + ? RADEON_CRTC_H_SYNC_POL + : 0)); + + fp_crtc_v_total_disp = (((mode->crtc_vtotal - 1) & 0xffff) + | ((mode->crtc_vdisplay - 1) << 16)); + + vsync_wid = mode->crtc_vsync_end - mode->crtc_vsync_start; + if (!vsync_wid) + vsync_wid = 1; + + fp_v_sync_strt_wid = (((mode->crtc_vsync_start - 1) & 0xfff) + | ((vsync_wid & 0x1f) << 16) + | ((mode->flags & DRM_MODE_FLAG_NVSYNC) + ? RADEON_CRTC_V_SYNC_POL + : 0)); + + fp_horz_vert_active = 0; + + if (native_mode->panel_xres == 0 || + native_mode->panel_yres == 0) { + hscale = false; + vscale = false; + } else { + if (xres > native_mode->panel_xres) + xres = native_mode->panel_xres; + if (yres > native_mode->panel_yres) + yres = native_mode->panel_yres; + + if (xres == native_mode->panel_xres) + hscale = false; + if (yres == native_mode->panel_yres) + vscale = false; + } + + switch (radeon_crtc->rmx_type) { + case RMX_FULL: + case RMX_ASPECT: + if (!hscale) + fp_horz_stretch |= ((xres/8-1) << 16); + else { + inc = (fp_horz_stretch & RADEON_HORZ_AUTO_RATIO_INC) ? 1 : 0; + scale = ((xres + inc) * RADEON_HORZ_STRETCH_RATIO_MAX) + / native_mode->panel_xres + 1; + fp_horz_stretch |= (((scale) & RADEON_HORZ_STRETCH_RATIO_MASK) | + RADEON_HORZ_STRETCH_BLEND | + RADEON_HORZ_STRETCH_ENABLE | + ((native_mode->panel_xres/8-1) << 16)); + } + + if (!vscale) + fp_vert_stretch |= ((yres-1) << 12); + else { + inc = (fp_vert_stretch & RADEON_VERT_AUTO_RATIO_INC) ? 1 : 0; + scale = ((yres + inc) * RADEON_VERT_STRETCH_RATIO_MAX) + / native_mode->panel_yres + 1; + fp_vert_stretch |= (((scale) & RADEON_VERT_STRETCH_RATIO_MASK) | + RADEON_VERT_STRETCH_ENABLE | + RADEON_VERT_STRETCH_BLEND | + ((native_mode->panel_yres-1) << 12)); + } + break; + case RMX_CENTER: + fp_horz_stretch |= ((xres/8-1) << 16); + fp_vert_stretch |= ((yres-1) << 12); + + crtc_more_cntl |= (RADEON_CRTC_AUTO_HORZ_CENTER_EN | + RADEON_CRTC_AUTO_VERT_CENTER_EN); + + blank_width = (mode->crtc_hblank_end - mode->crtc_hblank_start) / 8; + if (blank_width > 110) + blank_width = 110; + + fp_crtc_h_total_disp = (((blank_width) & 0x3ff) + | ((((mode->crtc_hdisplay / 8) - 1) & 0x1ff) << 16)); + + hsync_wid = (mode->crtc_hsync_end - mode->crtc_hsync_start) / 8; + if (!hsync_wid) + hsync_wid = 1; + + fp_h_sync_strt_wid = ((((mode->crtc_hsync_start - mode->crtc_hblank_start) / 8) & 0x1fff) + | ((hsync_wid & 0x3f) << 16) + | ((mode->flags & DRM_MODE_FLAG_NHSYNC) + ? RADEON_CRTC_H_SYNC_POL + : 0)); + + fp_crtc_v_total_disp = (((mode->crtc_vblank_end - mode->crtc_vblank_start) & 0xffff) + | ((mode->crtc_vdisplay - 1) << 16)); + + vsync_wid = mode->crtc_vsync_end - mode->crtc_vsync_start; + if (!vsync_wid) + vsync_wid = 1; + + fp_v_sync_strt_wid = ((((mode->crtc_vsync_start - mode->crtc_vblank_start) & 0xfff) + | ((vsync_wid & 0x1f) << 16) + | ((mode->flags & DRM_MODE_FLAG_NVSYNC) + ? RADEON_CRTC_V_SYNC_POL + : 0))); + + fp_horz_vert_active = (((native_mode->panel_yres) & 0xfff) | + (((native_mode->panel_xres / 8) & 0x1ff) << 16)); + break; + case RMX_OFF: + default: + fp_horz_stretch |= ((xres/8-1) << 16); + fp_vert_stretch |= ((yres-1) << 12); + break; + } + + WREG32(RADEON_FP_HORZ_STRETCH, fp_horz_stretch); + WREG32(RADEON_FP_VERT_STRETCH, fp_vert_stretch); + WREG32(RADEON_CRTC_MORE_CNTL, crtc_more_cntl); + WREG32(RADEON_FP_HORZ_VERT_ACTIVE, fp_horz_vert_active); + WREG32(RADEON_FP_H_SYNC_STRT_WID, fp_h_sync_strt_wid); + WREG32(RADEON_FP_V_SYNC_STRT_WID, fp_v_sync_strt_wid); + WREG32(RADEON_FP_CRTC_H_TOTAL_DISP, fp_crtc_h_total_disp); + WREG32(RADEON_FP_CRTC_V_TOTAL_DISP, fp_crtc_v_total_disp); +} + void radeon_restore_common_regs(struct drm_device *dev) { /* don't need this yet */ @@ -757,6 +922,8 @@ static bool radeon_crtc_mode_fixup(struct drm_crtc *crtc, struct drm_display_mode *mode, struct drm_display_mode *adjusted_mode) { + if (!radeon_crtc_scaling_mode_fixup(crtc, mode, adjusted_mode)) + return false; return true; } @@ -765,16 +932,25 @@ static int radeon_crtc_mode_set(struct drm_crtc *crtc, struct drm_display_mode *adjusted_mode, int x, int y, struct drm_framebuffer *old_fb) { - - DRM_DEBUG("\n"); + struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc); + struct drm_device *dev = crtc->dev; + struct radeon_device *rdev = dev->dev_private; /* TODO TV */ - radeon_crtc_set_base(crtc, x, y, old_fb); radeon_set_crtc_timing(crtc, adjusted_mode); radeon_set_pll(crtc, adjusted_mode); - radeon_init_disp_bandwidth(crtc->dev); - + radeon_bandwidth_update(rdev); + if (radeon_crtc->crtc_id == 0) { + radeon_legacy_rmx_mode_set(crtc, mode, adjusted_mode); + } else { + if (radeon_crtc->rmx_type != RMX_OFF) { + /* FIXME: only first crtc has rmx what should we + * do ? + */ + DRM_ERROR("Mode need scaling but only first crtc can do that.\n"); + } + } return 0; } @@ -805,478 +981,3 @@ void radeon_legacy_init_crtc(struct drm_device *dev, radeon_crtc->crtc_offset = RADEON_CRTC2_H_TOTAL_DISP - RADEON_CRTC_H_TOTAL_DISP; drm_crtc_helper_add(&radeon_crtc->base, &legacy_helper_funcs); } - -void radeon_init_disp_bw_legacy(struct drm_device *dev, - struct drm_display_mode *mode1, - uint32_t pixel_bytes1, - struct drm_display_mode *mode2, - uint32_t pixel_bytes2) -{ - struct radeon_device *rdev = dev->dev_private; - fixed20_12 trcd_ff, trp_ff, tras_ff, trbs_ff, tcas_ff; - fixed20_12 sclk_ff, mclk_ff, sclk_eff_ff, sclk_delay_ff; - fixed20_12 peak_disp_bw, mem_bw, pix_clk, pix_clk2, temp_ff, crit_point_ff; - uint32_t temp, data, mem_trcd, mem_trp, mem_tras; - fixed20_12 memtcas_ff[8] = { - fixed_init(1), - fixed_init(2), - fixed_init(3), - fixed_init(0), - fixed_init_half(1), - fixed_init_half(2), - fixed_init(0), - }; - fixed20_12 memtcas_rs480_ff[8] = { - fixed_init(0), - fixed_init(1), - fixed_init(2), - fixed_init(3), - fixed_init(0), - fixed_init_half(1), - fixed_init_half(2), - fixed_init_half(3), - }; - fixed20_12 memtcas2_ff[8] = { - fixed_init(0), - fixed_init(1), - fixed_init(2), - fixed_init(3), - fixed_init(4), - fixed_init(5), - fixed_init(6), - fixed_init(7), - }; - fixed20_12 memtrbs[8] = { - fixed_init(1), - fixed_init_half(1), - fixed_init(2), - fixed_init_half(2), - fixed_init(3), - fixed_init_half(3), - fixed_init(4), - fixed_init_half(4) - }; - fixed20_12 memtrbs_r4xx[8] = { - fixed_init(4), - fixed_init(5), - fixed_init(6), - fixed_init(7), - fixed_init(8), - fixed_init(9), - fixed_init(10), - fixed_init(11) - }; - fixed20_12 min_mem_eff; - fixed20_12 mc_latency_sclk, mc_latency_mclk, k1; - fixed20_12 cur_latency_mclk, cur_latency_sclk; - fixed20_12 disp_latency, disp_latency_overhead, disp_drain_rate, - disp_drain_rate2, read_return_rate; - fixed20_12 time_disp1_drop_priority; - int c; - int cur_size = 16; /* in octawords */ - int critical_point = 0, critical_point2; -/* uint32_t read_return_rate, time_disp1_drop_priority; */ - int stop_req, max_stop_req; - - min_mem_eff.full = rfixed_const_8(0); - /* get modes */ - if ((rdev->disp_priority == 2) && ASIC_IS_R300(rdev)) { - uint32_t mc_init_misc_lat_timer = RREG32(R300_MC_INIT_MISC_LAT_TIMER); - mc_init_misc_lat_timer &= ~(R300_MC_DISP1R_INIT_LAT_MASK << R300_MC_DISP1R_INIT_LAT_SHIFT); - mc_init_misc_lat_timer &= ~(R300_MC_DISP0R_INIT_LAT_MASK << R300_MC_DISP0R_INIT_LAT_SHIFT); - /* check crtc enables */ - if (mode2) - mc_init_misc_lat_timer |= (1 << R300_MC_DISP1R_INIT_LAT_SHIFT); - if (mode1) - mc_init_misc_lat_timer |= (1 << R300_MC_DISP0R_INIT_LAT_SHIFT); - WREG32(R300_MC_INIT_MISC_LAT_TIMER, mc_init_misc_lat_timer); - } - - /* - * determine is there is enough bw for current mode - */ - mclk_ff.full = rfixed_const(rdev->clock.default_mclk); - temp_ff.full = rfixed_const(100); - mclk_ff.full = rfixed_div(mclk_ff, temp_ff); - sclk_ff.full = rfixed_const(rdev->clock.default_sclk); - sclk_ff.full = rfixed_div(sclk_ff, temp_ff); - - temp = (rdev->mc.vram_width / 8) * (rdev->mc.vram_is_ddr ? 2 : 1); - temp_ff.full = rfixed_const(temp); - mem_bw.full = rfixed_mul(mclk_ff, temp_ff); - - pix_clk.full = 0; - pix_clk2.full = 0; - peak_disp_bw.full = 0; - if (mode1) { - temp_ff.full = rfixed_const(1000); - pix_clk.full = rfixed_const(mode1->clock); /* convert to fixed point */ - pix_clk.full = rfixed_div(pix_clk, temp_ff); - temp_ff.full = rfixed_const(pixel_bytes1); - peak_disp_bw.full += rfixed_mul(pix_clk, temp_ff); - } - if (mode2) { - temp_ff.full = rfixed_const(1000); - pix_clk2.full = rfixed_const(mode2->clock); /* convert to fixed point */ - pix_clk2.full = rfixed_div(pix_clk2, temp_ff); - temp_ff.full = rfixed_const(pixel_bytes2); - peak_disp_bw.full += rfixed_mul(pix_clk2, temp_ff); - } - - mem_bw.full = rfixed_mul(mem_bw, min_mem_eff); - if (peak_disp_bw.full >= mem_bw.full) { - DRM_ERROR("You may not have enough display bandwidth for current mode\n" - "If you have flickering problem, try to lower resolution, refresh rate, or color depth\n"); - } - - /* Get values from the EXT_MEM_CNTL register...converting its contents. */ - temp = RREG32(RADEON_MEM_TIMING_CNTL); - if ((rdev->family == CHIP_RV100) || (rdev->flags & RADEON_IS_IGP)) { /* RV100, M6, IGPs */ - mem_trcd = ((temp >> 2) & 0x3) + 1; - mem_trp = ((temp & 0x3)) + 1; - mem_tras = ((temp & 0x70) >> 4) + 1; - } else if (rdev->family == CHIP_R300 || - rdev->family == CHIP_R350) { /* r300, r350 */ - mem_trcd = (temp & 0x7) + 1; - mem_trp = ((temp >> 8) & 0x7) + 1; - mem_tras = ((temp >> 11) & 0xf) + 4; - } else if (rdev->family == CHIP_RV350 || - rdev->family <= CHIP_RV380) { - /* rv3x0 */ - mem_trcd = (temp & 0x7) + 3; - mem_trp = ((temp >> 8) & 0x7) + 3; - mem_tras = ((temp >> 11) & 0xf) + 6; - } else if (rdev->family == CHIP_R420 || - rdev->family == CHIP_R423 || - rdev->family == CHIP_RV410) { - /* r4xx */ - mem_trcd = (temp & 0xf) + 3; - if (mem_trcd > 15) - mem_trcd = 15; - mem_trp = ((temp >> 8) & 0xf) + 3; - if (mem_trp > 15) - mem_trp = 15; - mem_tras = ((temp >> 12) & 0x1f) + 6; - if (mem_tras > 31) - mem_tras = 31; - } else { /* RV200, R200 */ - mem_trcd = (temp & 0x7) + 1; - mem_trp = ((temp >> 8) & 0x7) + 1; - mem_tras = ((temp >> 12) & 0xf) + 4; - } - /* convert to FF */ - trcd_ff.full = rfixed_const(mem_trcd); - trp_ff.full = rfixed_const(mem_trp); - tras_ff.full = rfixed_const(mem_tras); - - /* Get values from the MEM_SDRAM_MODE_REG register...converting its */ - temp = RREG32(RADEON_MEM_SDRAM_MODE_REG); - data = (temp & (7 << 20)) >> 20; - if ((rdev->family == CHIP_RV100) || rdev->flags & RADEON_IS_IGP) { - if (rdev->family == CHIP_RS480) /* don't think rs400 */ - tcas_ff = memtcas_rs480_ff[data]; - else - tcas_ff = memtcas_ff[data]; - } else - tcas_ff = memtcas2_ff[data]; - - if (rdev->family == CHIP_RS400 || - rdev->family == CHIP_RS480) { - /* extra cas latency stored in bits 23-25 0-4 clocks */ - data = (temp >> 23) & 0x7; - if (data < 5) - tcas_ff.full += rfixed_const(data); - } - - if (ASIC_IS_R300(rdev) && !(rdev->flags & RADEON_IS_IGP)) { - /* on the R300, Tcas is included in Trbs. - */ - temp = RREG32(RADEON_MEM_CNTL); - data = (R300_MEM_NUM_CHANNELS_MASK & temp); - if (data == 1) { - if (R300_MEM_USE_CD_CH_ONLY & temp) { - temp = RREG32(R300_MC_IND_INDEX); - temp &= ~R300_MC_IND_ADDR_MASK; - temp |= R300_MC_READ_CNTL_CD_mcind; - WREG32(R300_MC_IND_INDEX, temp); - temp = RREG32(R300_MC_IND_DATA); - data = (R300_MEM_RBS_POSITION_C_MASK & temp); - } else { - temp = RREG32(R300_MC_READ_CNTL_AB); - data = (R300_MEM_RBS_POSITION_A_MASK & temp); - } - } else { - temp = RREG32(R300_MC_READ_CNTL_AB); - data = (R300_MEM_RBS_POSITION_A_MASK & temp); - } - if (rdev->family == CHIP_RV410 || - rdev->family == CHIP_R420 || - rdev->family == CHIP_R423) - trbs_ff = memtrbs_r4xx[data]; - else - trbs_ff = memtrbs[data]; - tcas_ff.full += trbs_ff.full; - } - - sclk_eff_ff.full = sclk_ff.full; - - if (rdev->flags & RADEON_IS_AGP) { - fixed20_12 agpmode_ff; - agpmode_ff.full = rfixed_const(radeon_agpmode); - temp_ff.full = rfixed_const_666(16); - sclk_eff_ff.full -= rfixed_mul(agpmode_ff, temp_ff); - } - /* TODO PCIE lanes may affect this - agpmode == 16?? */ - - if (ASIC_IS_R300(rdev)) { - sclk_delay_ff.full = rfixed_const(250); - } else { - if ((rdev->family == CHIP_RV100) || - rdev->flags & RADEON_IS_IGP) { - if (rdev->mc.vram_is_ddr) - sclk_delay_ff.full = rfixed_const(41); - else - sclk_delay_ff.full = rfixed_const(33); - } else { - if (rdev->mc.vram_width == 128) - sclk_delay_ff.full = rfixed_const(57); - else - sclk_delay_ff.full = rfixed_const(41); - } - } - - mc_latency_sclk.full = rfixed_div(sclk_delay_ff, sclk_eff_ff); - - if (rdev->mc.vram_is_ddr) { - if (rdev->mc.vram_width == 32) { - k1.full = rfixed_const(40); - c = 3; - } else { - k1.full = rfixed_const(20); - c = 1; - } - } else { - k1.full = rfixed_const(40); - c = 3; - } - - temp_ff.full = rfixed_const(2); - mc_latency_mclk.full = rfixed_mul(trcd_ff, temp_ff); - temp_ff.full = rfixed_const(c); - mc_latency_mclk.full += rfixed_mul(tcas_ff, temp_ff); - temp_ff.full = rfixed_const(4); - mc_latency_mclk.full += rfixed_mul(tras_ff, temp_ff); - mc_latency_mclk.full += rfixed_mul(trp_ff, temp_ff); - mc_latency_mclk.full += k1.full; - - mc_latency_mclk.full = rfixed_div(mc_latency_mclk, mclk_ff); - mc_latency_mclk.full += rfixed_div(temp_ff, sclk_eff_ff); - - /* - HW cursor time assuming worst case of full size colour cursor. - */ - temp_ff.full = rfixed_const((2 * (cur_size - (rdev->mc.vram_is_ddr + 1)))); - temp_ff.full += trcd_ff.full; - if (temp_ff.full < tras_ff.full) - temp_ff.full = tras_ff.full; - cur_latency_mclk.full = rfixed_div(temp_ff, mclk_ff); - - temp_ff.full = rfixed_const(cur_size); - cur_latency_sclk.full = rfixed_div(temp_ff, sclk_eff_ff); - /* - Find the total latency for the display data. - */ - disp_latency_overhead.full = rfixed_const(80); - disp_latency_overhead.full = rfixed_div(disp_latency_overhead, sclk_ff); - mc_latency_mclk.full += disp_latency_overhead.full + cur_latency_mclk.full; - mc_latency_sclk.full += disp_latency_overhead.full + cur_latency_sclk.full; - - if (mc_latency_mclk.full > mc_latency_sclk.full) - disp_latency.full = mc_latency_mclk.full; - else - disp_latency.full = mc_latency_sclk.full; - - /* setup Max GRPH_STOP_REQ default value */ - if (ASIC_IS_RV100(rdev)) - max_stop_req = 0x5c; - else - max_stop_req = 0x7c; - - if (mode1) { - /* CRTC1 - Set GRPH_BUFFER_CNTL register using h/w defined optimal values. - GRPH_STOP_REQ <= MIN[ 0x7C, (CRTC_H_DISP + 1) * (bit depth) / 0x10 ] - */ - stop_req = mode1->hdisplay * pixel_bytes1 / 16; - - if (stop_req > max_stop_req) - stop_req = max_stop_req; - - /* - Find the drain rate of the display buffer. - */ - temp_ff.full = rfixed_const((16/pixel_bytes1)); - disp_drain_rate.full = rfixed_div(pix_clk, temp_ff); - - /* - Find the critical point of the display buffer. - */ - crit_point_ff.full = rfixed_mul(disp_drain_rate, disp_latency); - crit_point_ff.full += rfixed_const_half(0); - - critical_point = rfixed_trunc(crit_point_ff); - - if (rdev->disp_priority == 2) { - critical_point = 0; - } - - /* - The critical point should never be above max_stop_req-4. Setting - GRPH_CRITICAL_CNTL = 0 will thus force high priority all the time. - */ - if (max_stop_req - critical_point < 4) - critical_point = 0; - - if (critical_point == 0 && mode2 && rdev->family == CHIP_R300) { - /* some R300 cards have problem with this set to 0, when CRTC2 is enabled.*/ - critical_point = 0x10; - } - - temp = RREG32(RADEON_GRPH_BUFFER_CNTL); - temp &= ~(RADEON_GRPH_STOP_REQ_MASK); - temp |= (stop_req << RADEON_GRPH_STOP_REQ_SHIFT); - temp &= ~(RADEON_GRPH_START_REQ_MASK); - if ((rdev->family == CHIP_R350) && - (stop_req > 0x15)) { - stop_req -= 0x10; - } - temp |= (stop_req << RADEON_GRPH_START_REQ_SHIFT); - temp |= RADEON_GRPH_BUFFER_SIZE; - temp &= ~(RADEON_GRPH_CRITICAL_CNTL | - RADEON_GRPH_CRITICAL_AT_SOF | - RADEON_GRPH_STOP_CNTL); - /* - Write the result into the register. - */ - WREG32(RADEON_GRPH_BUFFER_CNTL, ((temp & ~RADEON_GRPH_CRITICAL_POINT_MASK) | - (critical_point << RADEON_GRPH_CRITICAL_POINT_SHIFT))); - -#if 0 - if ((rdev->family == CHIP_RS400) || - (rdev->family == CHIP_RS480)) { - /* attempt to program RS400 disp regs correctly ??? */ - temp = RREG32(RS400_DISP1_REG_CNTL); - temp &= ~(RS400_DISP1_START_REQ_LEVEL_MASK | - RS400_DISP1_STOP_REQ_LEVEL_MASK); - WREG32(RS400_DISP1_REQ_CNTL1, (temp | - (critical_point << RS400_DISP1_START_REQ_LEVEL_SHIFT) | - (critical_point << RS400_DISP1_STOP_REQ_LEVEL_SHIFT))); - temp = RREG32(RS400_DMIF_MEM_CNTL1); - temp &= ~(RS400_DISP1_CRITICAL_POINT_START_MASK | - RS400_DISP1_CRITICAL_POINT_STOP_MASK); - WREG32(RS400_DMIF_MEM_CNTL1, (temp | - (critical_point << RS400_DISP1_CRITICAL_POINT_START_SHIFT) | - (critical_point << RS400_DISP1_CRITICAL_POINT_STOP_SHIFT))); - } -#endif - - DRM_DEBUG("GRPH_BUFFER_CNTL from to %x\n", - /* (unsigned int)info->SavedReg->grph_buffer_cntl, */ - (unsigned int)RREG32(RADEON_GRPH_BUFFER_CNTL)); - } - - if (mode2) { - u32 grph2_cntl; - stop_req = mode2->hdisplay * pixel_bytes2 / 16; - - if (stop_req > max_stop_req) - stop_req = max_stop_req; - - /* - Find the drain rate of the display buffer. - */ - temp_ff.full = rfixed_const((16/pixel_bytes2)); - disp_drain_rate2.full = rfixed_div(pix_clk2, temp_ff); - - grph2_cntl = RREG32(RADEON_GRPH2_BUFFER_CNTL); - grph2_cntl &= ~(RADEON_GRPH_STOP_REQ_MASK); - grph2_cntl |= (stop_req << RADEON_GRPH_STOP_REQ_SHIFT); - grph2_cntl &= ~(RADEON_GRPH_START_REQ_MASK); - if ((rdev->family == CHIP_R350) && - (stop_req > 0x15)) { - stop_req -= 0x10; - } - grph2_cntl |= (stop_req << RADEON_GRPH_START_REQ_SHIFT); - grph2_cntl |= RADEON_GRPH_BUFFER_SIZE; - grph2_cntl &= ~(RADEON_GRPH_CRITICAL_CNTL | - RADEON_GRPH_CRITICAL_AT_SOF | - RADEON_GRPH_STOP_CNTL); - - if ((rdev->family == CHIP_RS100) || - (rdev->family == CHIP_RS200)) - critical_point2 = 0; - else { - temp = (rdev->mc.vram_width * rdev->mc.vram_is_ddr + 1)/128; - temp_ff.full = rfixed_const(temp); - temp_ff.full = rfixed_mul(mclk_ff, temp_ff); - if (sclk_ff.full < temp_ff.full) - temp_ff.full = sclk_ff.full; - - read_return_rate.full = temp_ff.full; - - if (mode1) { - temp_ff.full = read_return_rate.full - disp_drain_rate.full; - time_disp1_drop_priority.full = rfixed_div(crit_point_ff, temp_ff); - } else { - time_disp1_drop_priority.full = 0; - } - crit_point_ff.full = disp_latency.full + time_disp1_drop_priority.full + disp_latency.full; - crit_point_ff.full = rfixed_mul(crit_point_ff, disp_drain_rate2); - crit_point_ff.full += rfixed_const_half(0); - - critical_point2 = rfixed_trunc(crit_point_ff); - - if (rdev->disp_priority == 2) { - critical_point2 = 0; - } - - if (max_stop_req - critical_point2 < 4) - critical_point2 = 0; - - } - - if (critical_point2 == 0 && rdev->family == CHIP_R300) { - /* some R300 cards have problem with this set to 0 */ - critical_point2 = 0x10; - } - - WREG32(RADEON_GRPH2_BUFFER_CNTL, ((grph2_cntl & ~RADEON_GRPH_CRITICAL_POINT_MASK) | - (critical_point2 << RADEON_GRPH_CRITICAL_POINT_SHIFT))); - - if ((rdev->family == CHIP_RS400) || - (rdev->family == CHIP_RS480)) { -#if 0 - /* attempt to program RS400 disp2 regs correctly ??? */ - temp = RREG32(RS400_DISP2_REQ_CNTL1); - temp &= ~(RS400_DISP2_START_REQ_LEVEL_MASK | - RS400_DISP2_STOP_REQ_LEVEL_MASK); - WREG32(RS400_DISP2_REQ_CNTL1, (temp | - (critical_point2 << RS400_DISP1_START_REQ_LEVEL_SHIFT) | - (critical_point2 << RS400_DISP1_STOP_REQ_LEVEL_SHIFT))); - temp = RREG32(RS400_DISP2_REQ_CNTL2); - temp &= ~(RS400_DISP2_CRITICAL_POINT_START_MASK | - RS400_DISP2_CRITICAL_POINT_STOP_MASK); - WREG32(RS400_DISP2_REQ_CNTL2, (temp | - (critical_point2 << RS400_DISP2_CRITICAL_POINT_START_SHIFT) | - (critical_point2 << RS400_DISP2_CRITICAL_POINT_STOP_SHIFT))); -#endif - WREG32(RS400_DISP2_REQ_CNTL1, 0x105DC1CC); - WREG32(RS400_DISP2_REQ_CNTL2, 0x2749D000); - WREG32(RS400_DMIF_MEM_CNTL1, 0x29CA71DC); - WREG32(RS400_DISP1_REQ_CNTL1, 0x28FBC3AC); - } - - DRM_DEBUG("GRPH2_BUFFER_CNTL from to %x\n", - (unsigned int)RREG32(RADEON_GRPH2_BUFFER_CNTL)); - } -} diff --git a/drivers/gpu/drm/radeon/radeon_legacy_encoders.c b/drivers/gpu/drm/radeon/radeon_legacy_encoders.c index 2c2f42de1d4..34d0f58eb94 100644 --- a/drivers/gpu/drm/radeon/radeon_legacy_encoders.c +++ b/drivers/gpu/drm/radeon/radeon_legacy_encoders.c @@ -30,170 +30,6 @@ #include "atom.h" -static void radeon_legacy_rmx_mode_set(struct drm_encoder *encoder, - struct drm_display_mode *mode, - struct drm_display_mode *adjusted_mode) -{ - struct drm_device *dev = encoder->dev; - struct radeon_device *rdev = dev->dev_private; - struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder); - int xres = mode->hdisplay; - int yres = mode->vdisplay; - bool hscale = true, vscale = true; - int hsync_wid; - int vsync_wid; - int hsync_start; - uint32_t scale, inc; - uint32_t fp_horz_stretch, fp_vert_stretch, crtc_more_cntl, fp_horz_vert_active; - uint32_t fp_h_sync_strt_wid, fp_v_sync_strt_wid, fp_crtc_h_total_disp, fp_crtc_v_total_disp; - struct radeon_native_mode *native_mode = &radeon_encoder->native_mode; - - DRM_DEBUG("\n"); - - fp_vert_stretch = RREG32(RADEON_FP_VERT_STRETCH) & - (RADEON_VERT_STRETCH_RESERVED | - RADEON_VERT_AUTO_RATIO_INC); - fp_horz_stretch = RREG32(RADEON_FP_HORZ_STRETCH) & - (RADEON_HORZ_FP_LOOP_STRETCH | - RADEON_HORZ_AUTO_RATIO_INC); - - crtc_more_cntl = 0; - if ((rdev->family == CHIP_RS100) || - (rdev->family == CHIP_RS200)) { - /* This is to workaround the asic bug for RMX, some versions - of BIOS dosen't have this register initialized correctly. */ - crtc_more_cntl |= RADEON_CRTC_H_CUTOFF_ACTIVE_EN; - } - - - fp_crtc_h_total_disp = ((((mode->crtc_htotal / 8) - 1) & 0x3ff) - | ((((mode->crtc_hdisplay / 8) - 1) & 0x1ff) << 16)); - - hsync_wid = (mode->crtc_hsync_end - mode->crtc_hsync_start) / 8; - if (!hsync_wid) - hsync_wid = 1; - hsync_start = mode->crtc_hsync_start - 8; - - fp_h_sync_strt_wid = ((hsync_start & 0x1fff) - | ((hsync_wid & 0x3f) << 16) - | ((mode->flags & DRM_MODE_FLAG_NHSYNC) - ? RADEON_CRTC_H_SYNC_POL - : 0)); - - fp_crtc_v_total_disp = (((mode->crtc_vtotal - 1) & 0xffff) - | ((mode->crtc_vdisplay - 1) << 16)); - - vsync_wid = mode->crtc_vsync_end - mode->crtc_vsync_start; - if (!vsync_wid) - vsync_wid = 1; - - fp_v_sync_strt_wid = (((mode->crtc_vsync_start - 1) & 0xfff) - | ((vsync_wid & 0x1f) << 16) - | ((mode->flags & DRM_MODE_FLAG_NVSYNC) - ? RADEON_CRTC_V_SYNC_POL - : 0)); - - fp_horz_vert_active = 0; - - if (native_mode->panel_xres == 0 || - native_mode->panel_yres == 0) { - hscale = false; - vscale = false; - } else { - if (xres > native_mode->panel_xres) - xres = native_mode->panel_xres; - if (yres > native_mode->panel_yres) - yres = native_mode->panel_yres; - - if (xres == native_mode->panel_xres) - hscale = false; - if (yres == native_mode->panel_yres) - vscale = false; - } - - if (radeon_encoder->flags & RADEON_USE_RMX) { - if (radeon_encoder->rmx_type != RMX_CENTER) { - if (!hscale) - fp_horz_stretch |= ((xres/8-1) << 16); - else { - inc = (fp_horz_stretch & RADEON_HORZ_AUTO_RATIO_INC) ? 1 : 0; - scale = ((xres + inc) * RADEON_HORZ_STRETCH_RATIO_MAX) - / native_mode->panel_xres + 1; - fp_horz_stretch |= (((scale) & RADEON_HORZ_STRETCH_RATIO_MASK) | - RADEON_HORZ_STRETCH_BLEND | - RADEON_HORZ_STRETCH_ENABLE | - ((native_mode->panel_xres/8-1) << 16)); - } - - if (!vscale) - fp_vert_stretch |= ((yres-1) << 12); - else { - inc = (fp_vert_stretch & RADEON_VERT_AUTO_RATIO_INC) ? 1 : 0; - scale = ((yres + inc) * RADEON_VERT_STRETCH_RATIO_MAX) - / native_mode->panel_yres + 1; - fp_vert_stretch |= (((scale) & RADEON_VERT_STRETCH_RATIO_MASK) | - RADEON_VERT_STRETCH_ENABLE | - RADEON_VERT_STRETCH_BLEND | - ((native_mode->panel_yres-1) << 12)); - } - } else if (radeon_encoder->rmx_type == RMX_CENTER) { - int blank_width; - - fp_horz_stretch |= ((xres/8-1) << 16); - fp_vert_stretch |= ((yres-1) << 12); - - crtc_more_cntl |= (RADEON_CRTC_AUTO_HORZ_CENTER_EN | - RADEON_CRTC_AUTO_VERT_CENTER_EN); - - blank_width = (mode->crtc_hblank_end - mode->crtc_hblank_start) / 8; - if (blank_width > 110) - blank_width = 110; - - fp_crtc_h_total_disp = (((blank_width) & 0x3ff) - | ((((mode->crtc_hdisplay / 8) - 1) & 0x1ff) << 16)); - - hsync_wid = (mode->crtc_hsync_end - mode->crtc_hsync_start) / 8; - if (!hsync_wid) - hsync_wid = 1; - - fp_h_sync_strt_wid = ((((mode->crtc_hsync_start - mode->crtc_hblank_start) / 8) & 0x1fff) - | ((hsync_wid & 0x3f) << 16) - | ((mode->flags & DRM_MODE_FLAG_NHSYNC) - ? RADEON_CRTC_H_SYNC_POL - : 0)); - - fp_crtc_v_total_disp = (((mode->crtc_vblank_end - mode->crtc_vblank_start) & 0xffff) - | ((mode->crtc_vdisplay - 1) << 16)); - - vsync_wid = mode->crtc_vsync_end - mode->crtc_vsync_start; - if (!vsync_wid) - vsync_wid = 1; - - fp_v_sync_strt_wid = ((((mode->crtc_vsync_start - mode->crtc_vblank_start) & 0xfff) - | ((vsync_wid & 0x1f) << 16) - | ((mode->flags & DRM_MODE_FLAG_NVSYNC) - ? RADEON_CRTC_V_SYNC_POL - : 0))); - - fp_horz_vert_active = (((native_mode->panel_yres) & 0xfff) | - (((native_mode->panel_xres / 8) & 0x1ff) << 16)); - } - } else { - fp_horz_stretch |= ((xres/8-1) << 16); - fp_vert_stretch |= ((yres-1) << 12); - } - - WREG32(RADEON_FP_HORZ_STRETCH, fp_horz_stretch); - WREG32(RADEON_FP_VERT_STRETCH, fp_vert_stretch); - WREG32(RADEON_CRTC_MORE_CNTL, crtc_more_cntl); - WREG32(RADEON_FP_HORZ_VERT_ACTIVE, fp_horz_vert_active); - WREG32(RADEON_FP_H_SYNC_STRT_WID, fp_h_sync_strt_wid); - WREG32(RADEON_FP_V_SYNC_STRT_WID, fp_v_sync_strt_wid); - WREG32(RADEON_FP_CRTC_H_TOTAL_DISP, fp_crtc_h_total_disp); - WREG32(RADEON_FP_CRTC_V_TOTAL_DISP, fp_crtc_v_total_disp); - -} - static void radeon_legacy_lvds_dpms(struct drm_encoder *encoder, int mode) { struct drm_device *dev = encoder->dev; @@ -287,9 +123,6 @@ static void radeon_legacy_lvds_mode_set(struct drm_encoder *encoder, DRM_DEBUG("\n"); - if (radeon_crtc->crtc_id == 0) - radeon_legacy_rmx_mode_set(encoder, mode, adjusted_mode); - lvds_pll_cntl = RREG32(RADEON_LVDS_PLL_CNTL); lvds_pll_cntl &= ~RADEON_LVDS_PLL_EN; @@ -318,7 +151,7 @@ static void radeon_legacy_lvds_mode_set(struct drm_encoder *encoder, if (radeon_crtc->crtc_id == 0) { if (ASIC_IS_R300(rdev)) { - if (radeon_encoder->flags & RADEON_USE_RMX) + if (radeon_encoder->rmx_type != RMX_OFF) lvds_pll_cntl |= R300_LVDS_SRC_SEL_RMX; } else lvds_gen_cntl &= ~RADEON_LVDS_SEL_CRTC2; @@ -350,8 +183,6 @@ static bool radeon_legacy_lvds_mode_fixup(struct drm_encoder *encoder, drm_mode_set_crtcinfo(adjusted_mode, 0); - radeon_encoder->flags &= ~RADEON_USE_RMX; - if (radeon_encoder->rmx_type != RMX_OFF) radeon_rmx_mode_fixup(encoder, mode, adjusted_mode); @@ -455,9 +286,6 @@ static void radeon_legacy_primary_dac_mode_set(struct drm_encoder *encoder, DRM_DEBUG("\n"); - if (radeon_crtc->crtc_id == 0) - radeon_legacy_rmx_mode_set(encoder, mode, adjusted_mode); - if (radeon_crtc->crtc_id == 0) { if (rdev->family == CHIP_R200 || ASIC_IS_R300(rdev)) { disp_output_cntl = RREG32(RADEON_DISP_OUTPUT_CNTL) & @@ -653,9 +481,6 @@ static void radeon_legacy_tmds_int_mode_set(struct drm_encoder *encoder, DRM_DEBUG("\n"); - if (radeon_crtc->crtc_id == 0) - radeon_legacy_rmx_mode_set(encoder, mode, adjusted_mode); - tmp = tmds_pll_cntl = RREG32(RADEON_TMDS_PLL_CNTL); tmp &= 0xfffff; if (rdev->family == CHIP_RV280) { @@ -711,7 +536,7 @@ static void radeon_legacy_tmds_int_mode_set(struct drm_encoder *encoder, if (radeon_crtc->crtc_id == 0) { if (ASIC_IS_R300(rdev) || rdev->family == CHIP_R200) { fp_gen_cntl &= ~R200_FP_SOURCE_SEL_MASK; - if (radeon_encoder->flags & RADEON_USE_RMX) + if (radeon_encoder->rmx_type != RMX_OFF) fp_gen_cntl |= R200_FP_SOURCE_SEL_RMX; else fp_gen_cntl |= R200_FP_SOURCE_SEL_CRTC1; @@ -820,9 +645,6 @@ static void radeon_legacy_tmds_ext_mode_set(struct drm_encoder *encoder, DRM_DEBUG("\n"); - if (radeon_crtc->crtc_id == 0) - radeon_legacy_rmx_mode_set(encoder, mode, adjusted_mode); - if (rdev->is_atom_bios) { radeon_encoder->pixel_clock = adjusted_mode->clock; atombios_external_tmds_setup(encoder, ATOM_ENABLE); @@ -856,7 +678,7 @@ static void radeon_legacy_tmds_ext_mode_set(struct drm_encoder *encoder, if (radeon_crtc->crtc_id == 0) { if ((rdev->family == CHIP_R200) || ASIC_IS_R300(rdev)) { fp2_gen_cntl &= ~R200_FP2_SOURCE_SEL_MASK; - if (radeon_encoder->flags & RADEON_USE_RMX) + if (radeon_encoder->rmx_type != RMX_OFF) fp2_gen_cntl |= R200_FP2_SOURCE_SEL_RMX; else fp2_gen_cntl |= R200_FP2_SOURCE_SEL_CRTC1; @@ -1014,9 +836,6 @@ static void radeon_legacy_tv_dac_mode_set(struct drm_encoder *encoder, DRM_DEBUG("\n"); - if (radeon_crtc->crtc_id == 0) - radeon_legacy_rmx_mode_set(encoder, mode, adjusted_mode); - if (rdev->family != CHIP_R200) { tv_dac_cntl = RREG32(RADEON_TV_DAC_CNTL); if (rdev->family == CHIP_R420 || @@ -1243,6 +1062,7 @@ radeon_add_legacy_encoder(struct drm_device *dev, uint32_t encoder_id, uint32_t radeon_encoder->encoder_id = encoder_id; radeon_encoder->devices = supported_device; + radeon_encoder->rmx_type = RMX_OFF; switch (radeon_encoder->encoder_id) { case ENCODER_OBJECT_ID_INTERNAL_LVDS: diff --git a/drivers/gpu/drm/radeon/radeon_mode.h b/drivers/gpu/drm/radeon/radeon_mode.h index ba89b59f6e5..3b09a1f2d8f 100644 --- a/drivers/gpu/drm/radeon/radeon_mode.h +++ b/drivers/gpu/drm/radeon/radeon_mode.h @@ -36,6 +36,9 @@ #include #include #include +#include "radeon_fixed.h" + +struct radeon_device; #define to_radeon_crtc(x) container_of(x, struct radeon_crtc, base) #define to_radeon_connector(x) container_of(x, struct radeon_connector, base) @@ -171,6 +174,18 @@ struct radeon_mode_info { struct atom_context *atom_context; enum radeon_connector_table connector_table; bool mode_config_initialized; + struct radeon_crtc *crtcs[2]; +}; + +struct radeon_native_mode { + /* preferred mode */ + uint32_t panel_xres, panel_yres; + uint32_t hoverplus, hsync_width; + uint32_t hblank; + uint32_t voverplus, vsync_width; + uint32_t vblank; + uint32_t dotclock; + uint32_t flags; }; struct radeon_crtc { @@ -188,19 +203,11 @@ struct radeon_crtc { int cursor_height; uint32_t legacy_display_base_addr; uint32_t legacy_cursor_offset; -}; - -#define RADEON_USE_RMX 1 - -struct radeon_native_mode { - /* preferred mode */ - uint32_t panel_xres, panel_yres; - uint32_t hoverplus, hsync_width; - uint32_t hblank; - uint32_t voverplus, vsync_width; - uint32_t vblank; - uint32_t dotclock; - uint32_t flags; + enum radeon_rmx_type rmx_type; + uint32_t devices; + fixed20_12 vsc; + fixed20_12 hsc; + struct radeon_native_mode native_mode; }; struct radeon_encoder_primary_dac { @@ -386,16 +393,9 @@ void radeon_enc_destroy(struct drm_encoder *encoder); void radeon_copy_fb(struct drm_device *dev, struct drm_gem_object *dst_obj); void radeon_combios_asic_init(struct drm_device *dev); extern int radeon_static_clocks_init(struct drm_device *dev); -void radeon_init_disp_bw_legacy(struct drm_device *dev, - struct drm_display_mode *mode1, - uint32_t pixel_bytes1, - struct drm_display_mode *mode2, - uint32_t pixel_bytes2); -void radeon_init_disp_bw_avivo(struct drm_device *dev, - struct drm_display_mode *mode1, - uint32_t pixel_bytes1, - struct drm_display_mode *mode2, - uint32_t pixel_bytes2); -void radeon_init_disp_bandwidth(struct drm_device *dev); +bool radeon_crtc_scaling_mode_fixup(struct drm_crtc *crtc, + struct drm_display_mode *mode, + struct drm_display_mode *adjusted_mode); +void atom_rv515_force_tv_scaler(struct radeon_device *rdev); #endif diff --git a/drivers/gpu/drm/radeon/radeon_share.h b/drivers/gpu/drm/radeon/radeon_share.h new file mode 100644 index 00000000000..63a773578f1 --- /dev/null +++ b/drivers/gpu/drm/radeon/radeon_share.h @@ -0,0 +1,39 @@ +/* + * Copyright 2008 Advanced Micro Devices, Inc. + * Copyright 2008 Red Hat Inc. + * Copyright 2009 Jerome Glisse. + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the "Software"), + * to deal in the Software without restriction, including without limitation + * the rights to use, copy, modify, merge, publish, distribute, sublicense, + * and/or sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR + * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, + * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + * + * Authors: Dave Airlie + * Alex Deucher + * Jerome Glisse + */ +#ifndef __RADEON_SHARE_H__ +#define __RADEON_SHARE_H__ + +void r100_vram_init_sizes(struct radeon_device *rdev); + +void rs690_line_buffer_adjust(struct radeon_device *rdev, + struct drm_display_mode *mode1, + struct drm_display_mode *mode2); + +void rv515_bandwidth_avivo_update(struct radeon_device *rdev); + +#endif diff --git a/drivers/gpu/drm/radeon/rs400.c b/drivers/gpu/drm/radeon/rs400.c index daf24e85cba..96a3c8486d2 100644 --- a/drivers/gpu/drm/radeon/rs400.c +++ b/drivers/gpu/drm/radeon/rs400.c @@ -29,6 +29,7 @@ #include #include "radeon_reg.h" #include "radeon.h" +#include "radeon_share.h" /* rs400,rs480 depends on : */ void r100_hdp_reset(struct radeon_device *rdev); diff --git a/drivers/gpu/drm/radeon/rs600.c b/drivers/gpu/drm/radeon/rs600.c index ab0c967553e..bccdce7fd37 100644 --- a/drivers/gpu/drm/radeon/rs600.c +++ b/drivers/gpu/drm/radeon/rs600.c @@ -301,6 +301,11 @@ void rs600_vram_info(struct radeon_device *rdev) rdev->mc.vram_width = 128; } +void rs600_bandwidth_update(struct radeon_device *rdev) +{ + /* FIXME: implement, should this be like rs690 ? */ +} + /* * Indirect registers accessor diff --git a/drivers/gpu/drm/radeon/rs690.c b/drivers/gpu/drm/radeon/rs690.c index 79ba85042b5..97eaee3d28b 100644 --- a/drivers/gpu/drm/radeon/rs690.c +++ b/drivers/gpu/drm/radeon/rs690.c @@ -28,6 +28,9 @@ #include "drmP.h" #include "radeon_reg.h" #include "radeon.h" +#include "rs690r.h" +#include "atom.h" +#include "atom-bits.h" /* rs690,rs740 depends on : */ void r100_hdp_reset(struct radeon_device *rdev); @@ -138,9 +141,82 @@ void rs690_gpu_init(struct radeon_device *rdev) /* * VRAM info. */ +void rs690_pm_info(struct radeon_device *rdev) +{ + int index = GetIndexIntoMasterTable(DATA, IntegratedSystemInfo); + struct _ATOM_INTEGRATED_SYSTEM_INFO *info; + struct _ATOM_INTEGRATED_SYSTEM_INFO_V2 *info_v2; + void *ptr; + uint16_t data_offset; + uint8_t frev, crev; + fixed20_12 tmp; + + atom_parse_data_header(rdev->mode_info.atom_context, index, NULL, + &frev, &crev, &data_offset); + ptr = rdev->mode_info.atom_context->bios + data_offset; + info = (struct _ATOM_INTEGRATED_SYSTEM_INFO *)ptr; + info_v2 = (struct _ATOM_INTEGRATED_SYSTEM_INFO_V2 *)ptr; + /* Get various system informations from bios */ + switch (crev) { + case 1: + tmp.full = rfixed_const(100); + rdev->pm.igp_sideport_mclk.full = rfixed_const(info->ulBootUpMemoryClock); + rdev->pm.igp_sideport_mclk.full = rfixed_div(rdev->pm.igp_sideport_mclk, tmp); + rdev->pm.igp_system_mclk.full = rfixed_const(le16_to_cpu(info->usK8MemoryClock)); + rdev->pm.igp_ht_link_clk.full = rfixed_const(le16_to_cpu(info->usFSBClock)); + rdev->pm.igp_ht_link_width.full = rfixed_const(info->ucHTLinkWidth); + break; + case 2: + tmp.full = rfixed_const(100); + rdev->pm.igp_sideport_mclk.full = rfixed_const(info_v2->ulBootUpSidePortClock); + rdev->pm.igp_sideport_mclk.full = rfixed_div(rdev->pm.igp_sideport_mclk, tmp); + rdev->pm.igp_system_mclk.full = rfixed_const(info_v2->ulBootUpUMAClock); + rdev->pm.igp_system_mclk.full = rfixed_div(rdev->pm.igp_system_mclk, tmp); + rdev->pm.igp_ht_link_clk.full = rfixed_const(info_v2->ulHTLinkFreq); + rdev->pm.igp_ht_link_clk.full = rfixed_div(rdev->pm.igp_ht_link_clk, tmp); + rdev->pm.igp_ht_link_width.full = rfixed_const(le16_to_cpu(info_v2->usMinHTLinkWidth)); + break; + default: + tmp.full = rfixed_const(100); + /* We assume the slower possible clock ie worst case */ + /* DDR 333Mhz */ + rdev->pm.igp_sideport_mclk.full = rfixed_const(333); + /* FIXME: system clock ? */ + rdev->pm.igp_system_mclk.full = rfixed_const(100); + rdev->pm.igp_system_mclk.full = rfixed_div(rdev->pm.igp_system_mclk, tmp); + rdev->pm.igp_ht_link_clk.full = rfixed_const(200); + rdev->pm.igp_ht_link_width.full = rfixed_const(8); + DRM_ERROR("No integrated system info for your GPU, using safe default\n"); + break; + } + /* Compute various bandwidth */ + /* k8_bandwidth = (memory_clk / 2) * 2 * 8 * 0.5 = memory_clk * 4 */ + tmp.full = rfixed_const(4); + rdev->pm.k8_bandwidth.full = rfixed_mul(rdev->pm.igp_system_mclk, tmp); + /* ht_bandwidth = ht_clk * 2 * ht_width / 8 * 0.8 + * = ht_clk * ht_width / 5 + */ + tmp.full = rfixed_const(5); + rdev->pm.ht_bandwidth.full = rfixed_mul(rdev->pm.igp_ht_link_clk, + rdev->pm.igp_ht_link_width); + rdev->pm.ht_bandwidth.full = rfixed_div(rdev->pm.ht_bandwidth, tmp); + if (tmp.full < rdev->pm.max_bandwidth.full) { + /* HT link is a limiting factor */ + rdev->pm.max_bandwidth.full = tmp.full; + } + /* sideport_bandwidth = (sideport_clk / 2) * 2 * 2 * 0.7 + * = (sideport_clk * 14) / 10 + */ + tmp.full = rfixed_const(14); + rdev->pm.sideport_bandwidth.full = rfixed_mul(rdev->pm.igp_sideport_mclk, tmp); + tmp.full = rfixed_const(10); + rdev->pm.sideport_bandwidth.full = rfixed_div(rdev->pm.sideport_bandwidth, tmp); +} + void rs690_vram_info(struct radeon_device *rdev) { uint32_t tmp; + fixed20_12 a; rs400_gart_adjust_size(rdev); /* DDR for all card after R300 & IGP */ @@ -156,8 +232,404 @@ void rs690_vram_info(struct radeon_device *rdev) rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); + rs690_pm_info(rdev); + /* FIXME: we should enforce default clock in case GPU is not in + * default setup + */ + a.full = rfixed_const(100); + rdev->pm.sclk.full = rfixed_const(rdev->clock.default_sclk); + rdev->pm.sclk.full = rfixed_div(rdev->pm.sclk, a); + a.full = rfixed_const(16); + /* core_bandwidth = sclk(Mhz) * 16 */ + rdev->pm.core_bandwidth.full = rfixed_div(rdev->pm.sclk, a); +} + +void rs690_line_buffer_adjust(struct radeon_device *rdev, + struct drm_display_mode *mode1, + struct drm_display_mode *mode2) +{ + u32 tmp; + + /* + * Line Buffer Setup + * There is a single line buffer shared by both display controllers. + * DC_LB_MEMORY_SPLIT controls how that line buffer is shared between + * the display controllers. The paritioning can either be done + * manually or via one of four preset allocations specified in bits 1:0: + * 0 - line buffer is divided in half and shared between crtc + * 1 - D1 gets 3/4 of the line buffer, D2 gets 1/4 + * 2 - D1 gets the whole buffer + * 3 - D1 gets 1/4 of the line buffer, D2 gets 3/4 + * Setting bit 2 of DC_LB_MEMORY_SPLIT controls switches to manual + * allocation mode. In manual allocation mode, D1 always starts at 0, + * D1 end/2 is specified in bits 14:4; D2 allocation follows D1. + */ + tmp = RREG32(DC_LB_MEMORY_SPLIT) & ~DC_LB_MEMORY_SPLIT_MASK; + tmp &= ~DC_LB_MEMORY_SPLIT_SHIFT_MODE; + /* auto */ + if (mode1 && mode2) { + if (mode1->hdisplay > mode2->hdisplay) { + if (mode1->hdisplay > 2560) + tmp |= DC_LB_MEMORY_SPLIT_D1_3Q_D2_1Q; + else + tmp |= DC_LB_MEMORY_SPLIT_D1HALF_D2HALF; + } else if (mode2->hdisplay > mode1->hdisplay) { + if (mode2->hdisplay > 2560) + tmp |= DC_LB_MEMORY_SPLIT_D1_1Q_D2_3Q; + else + tmp |= DC_LB_MEMORY_SPLIT_D1HALF_D2HALF; + } else + tmp |= AVIVO_DC_LB_MEMORY_SPLIT_D1HALF_D2HALF; + } else if (mode1) { + tmp |= DC_LB_MEMORY_SPLIT_D1_ONLY; + } else if (mode2) { + tmp |= DC_LB_MEMORY_SPLIT_D1_1Q_D2_3Q; + } + WREG32(DC_LB_MEMORY_SPLIT, tmp); } +struct rs690_watermark { + u32 lb_request_fifo_depth; + fixed20_12 num_line_pair; + fixed20_12 estimated_width; + fixed20_12 worst_case_latency; + fixed20_12 consumption_rate; + fixed20_12 active_time; + fixed20_12 dbpp; + fixed20_12 priority_mark_max; + fixed20_12 priority_mark; + fixed20_12 sclk; +}; + +void rs690_crtc_bandwidth_compute(struct radeon_device *rdev, + struct radeon_crtc *crtc, + struct rs690_watermark *wm) +{ + struct drm_display_mode *mode = &crtc->base.mode; + fixed20_12 a, b, c; + fixed20_12 pclk, request_fifo_depth, tolerable_latency, estimated_width; + fixed20_12 consumption_time, line_time, chunk_time, read_delay_latency; + /* FIXME: detect IGP with sideport memory, i don't think there is any + * such product available + */ + bool sideport = false; + + if (!crtc->base.enabled) { + /* FIXME: wouldn't it better to set priority mark to maximum */ + wm->lb_request_fifo_depth = 4; + return; + } + + if (crtc->vsc.full > rfixed_const(2)) + wm->num_line_pair.full = rfixed_const(2); + else + wm->num_line_pair.full = rfixed_const(1); + + b.full = rfixed_const(mode->crtc_hdisplay); + c.full = rfixed_const(256); + a.full = rfixed_mul(wm->num_line_pair, b); + request_fifo_depth.full = rfixed_div(a, c); + if (a.full < rfixed_const(4)) { + wm->lb_request_fifo_depth = 4; + } else { + wm->lb_request_fifo_depth = rfixed_trunc(request_fifo_depth); + } + + /* Determine consumption rate + * pclk = pixel clock period(ns) = 1000 / (mode.clock / 1000) + * vtaps = number of vertical taps, + * vsc = vertical scaling ratio, defined as source/destination + * hsc = horizontal scaling ration, defined as source/destination + */ + a.full = rfixed_const(mode->clock); + b.full = rfixed_const(1000); + a.full = rfixed_div(a, b); + pclk.full = rfixed_div(b, a); + if (crtc->rmx_type != RMX_OFF) { + b.full = rfixed_const(2); + if (crtc->vsc.full > b.full) + b.full = crtc->vsc.full; + b.full = rfixed_mul(b, crtc->hsc); + c.full = rfixed_const(2); + b.full = rfixed_div(b, c); + consumption_time.full = rfixed_div(pclk, b); + } else { + consumption_time.full = pclk.full; + } + a.full = rfixed_const(1); + wm->consumption_rate.full = rfixed_div(a, consumption_time); + + + /* Determine line time + * LineTime = total time for one line of displayhtotal + * LineTime = total number of horizontal pixels + * pclk = pixel clock period(ns) + */ + a.full = rfixed_const(crtc->base.mode.crtc_htotal); + line_time.full = rfixed_mul(a, pclk); + + /* Determine active time + * ActiveTime = time of active region of display within one line, + * hactive = total number of horizontal active pixels + * htotal = total number of horizontal pixels + */ + a.full = rfixed_const(crtc->base.mode.crtc_htotal); + b.full = rfixed_const(crtc->base.mode.crtc_hdisplay); + wm->active_time.full = rfixed_mul(line_time, b); + wm->active_time.full = rfixed_div(wm->active_time, a); + + /* Maximun bandwidth is the minimun bandwidth of all component */ + rdev->pm.max_bandwidth = rdev->pm.core_bandwidth; + if (sideport) { + if (rdev->pm.max_bandwidth.full > rdev->pm.sideport_bandwidth.full && + rdev->pm.sideport_bandwidth.full) + rdev->pm.max_bandwidth = rdev->pm.sideport_bandwidth; + read_delay_latency.full = rfixed_const(370 * 800 * 1000); + read_delay_latency.full = rfixed_div(read_delay_latency, + rdev->pm.igp_sideport_mclk); + } else { + if (rdev->pm.max_bandwidth.full > rdev->pm.k8_bandwidth.full && + rdev->pm.k8_bandwidth.full) + rdev->pm.max_bandwidth = rdev->pm.k8_bandwidth; + if (rdev->pm.max_bandwidth.full > rdev->pm.ht_bandwidth.full && + rdev->pm.ht_bandwidth.full) + rdev->pm.max_bandwidth = rdev->pm.ht_bandwidth; + read_delay_latency.full = rfixed_const(5000); + } + + /* sclk = system clocks(ns) = 1000 / max_bandwidth / 16 */ + a.full = rfixed_const(16); + rdev->pm.sclk.full = rfixed_mul(rdev->pm.max_bandwidth, a); + a.full = rfixed_const(1000); + rdev->pm.sclk.full = rfixed_div(a, rdev->pm.sclk); + /* Determine chunk time + * ChunkTime = the time it takes the DCP to send one chunk of data + * to the LB which consists of pipeline delay and inter chunk gap + * sclk = system clock(ns) + */ + a.full = rfixed_const(256 * 13); + chunk_time.full = rfixed_mul(rdev->pm.sclk, a); + a.full = rfixed_const(10); + chunk_time.full = rfixed_div(chunk_time, a); + + /* Determine the worst case latency + * NumLinePair = Number of line pairs to request(1=2 lines, 2=4 lines) + * WorstCaseLatency = worst case time from urgent to when the MC starts + * to return data + * READ_DELAY_IDLE_MAX = constant of 1us + * ChunkTime = time it takes the DCP to send one chunk of data to the LB + * which consists of pipeline delay and inter chunk gap + */ + if (rfixed_trunc(wm->num_line_pair) > 1) { + a.full = rfixed_const(3); + wm->worst_case_latency.full = rfixed_mul(a, chunk_time); + wm->worst_case_latency.full += read_delay_latency.full; + } else { + a.full = rfixed_const(2); + wm->worst_case_latency.full = rfixed_mul(a, chunk_time); + wm->worst_case_latency.full += read_delay_latency.full; + } + + /* Determine the tolerable latency + * TolerableLatency = Any given request has only 1 line time + * for the data to be returned + * LBRequestFifoDepth = Number of chunk requests the LB can + * put into the request FIFO for a display + * LineTime = total time for one line of display + * ChunkTime = the time it takes the DCP to send one chunk + * of data to the LB which consists of + * pipeline delay and inter chunk gap + */ + if ((2+wm->lb_request_fifo_depth) >= rfixed_trunc(request_fifo_depth)) { + tolerable_latency.full = line_time.full; + } else { + tolerable_latency.full = rfixed_const(wm->lb_request_fifo_depth - 2); + tolerable_latency.full = request_fifo_depth.full - tolerable_latency.full; + tolerable_latency.full = rfixed_mul(tolerable_latency, chunk_time); + tolerable_latency.full = line_time.full - tolerable_latency.full; + } + /* We assume worst case 32bits (4 bytes) */ + wm->dbpp.full = rfixed_const(4 * 8); + + /* Determine the maximum priority mark + * width = viewport width in pixels + */ + a.full = rfixed_const(16); + wm->priority_mark_max.full = rfixed_const(crtc->base.mode.crtc_hdisplay); + wm->priority_mark_max.full = rfixed_div(wm->priority_mark_max, a); + + /* Determine estimated width */ + estimated_width.full = tolerable_latency.full - wm->worst_case_latency.full; + estimated_width.full = rfixed_div(estimated_width, consumption_time); + if (rfixed_trunc(estimated_width) > crtc->base.mode.crtc_hdisplay) { + wm->priority_mark.full = rfixed_const(10); + } else { + a.full = rfixed_const(16); + wm->priority_mark.full = rfixed_div(estimated_width, a); + wm->priority_mark.full = wm->priority_mark_max.full - wm->priority_mark.full; + } +} + +void rs690_bandwidth_update(struct radeon_device *rdev) +{ + struct drm_display_mode *mode0 = NULL; + struct drm_display_mode *mode1 = NULL; + struct rs690_watermark wm0; + struct rs690_watermark wm1; + u32 tmp; + fixed20_12 priority_mark02, priority_mark12, fill_rate; + fixed20_12 a, b; + + if (rdev->mode_info.crtcs[0]->base.enabled) + mode0 = &rdev->mode_info.crtcs[0]->base.mode; + if (rdev->mode_info.crtcs[1]->base.enabled) + mode1 = &rdev->mode_info.crtcs[1]->base.mode; + /* + * Set display0/1 priority up in the memory controller for + * modes if the user specifies HIGH for displaypriority + * option. + */ + if (rdev->disp_priority == 2) { + tmp = RREG32_MC(MC_INIT_MISC_LAT_TIMER); + tmp &= ~MC_DISP1R_INIT_LAT_MASK; + tmp &= ~MC_DISP0R_INIT_LAT_MASK; + if (mode1) + tmp |= (1 << MC_DISP1R_INIT_LAT_SHIFT); + if (mode0) + tmp |= (1 << MC_DISP0R_INIT_LAT_SHIFT); + WREG32_MC(MC_INIT_MISC_LAT_TIMER, tmp); + } + rs690_line_buffer_adjust(rdev, mode0, mode1); + + if ((rdev->family == CHIP_RS690) || (rdev->family == CHIP_RS740)) + WREG32(DCP_CONTROL, 0); + if ((rdev->family == CHIP_RS780) || (rdev->family == CHIP_RS880)) + WREG32(DCP_CONTROL, 2); + + rs690_crtc_bandwidth_compute(rdev, rdev->mode_info.crtcs[0], &wm0); + rs690_crtc_bandwidth_compute(rdev, rdev->mode_info.crtcs[1], &wm1); + + tmp = (wm0.lb_request_fifo_depth - 1); + tmp |= (wm1.lb_request_fifo_depth - 1) << 16; + WREG32(LB_MAX_REQ_OUTSTANDING, tmp); + + if (mode0 && mode1) { + if (rfixed_trunc(wm0.dbpp) > 64) + a.full = rfixed_mul(wm0.dbpp, wm0.num_line_pair); + else + a.full = wm0.num_line_pair.full; + if (rfixed_trunc(wm1.dbpp) > 64) + b.full = rfixed_mul(wm1.dbpp, wm1.num_line_pair); + else + b.full = wm1.num_line_pair.full; + a.full += b.full; + fill_rate.full = rfixed_div(wm0.sclk, a); + if (wm0.consumption_rate.full > fill_rate.full) { + b.full = wm0.consumption_rate.full - fill_rate.full; + b.full = rfixed_mul(b, wm0.active_time); + a.full = rfixed_mul(wm0.worst_case_latency, + wm0.consumption_rate); + a.full = a.full + b.full; + b.full = rfixed_const(16 * 1000); + priority_mark02.full = rfixed_div(a, b); + } else { + a.full = rfixed_mul(wm0.worst_case_latency, + wm0.consumption_rate); + b.full = rfixed_const(16 * 1000); + priority_mark02.full = rfixed_div(a, b); + } + if (wm1.consumption_rate.full > fill_rate.full) { + b.full = wm1.consumption_rate.full - fill_rate.full; + b.full = rfixed_mul(b, wm1.active_time); + a.full = rfixed_mul(wm1.worst_case_latency, + wm1.consumption_rate); + a.full = a.full + b.full; + b.full = rfixed_const(16 * 1000); + priority_mark12.full = rfixed_div(a, b); + } else { + a.full = rfixed_mul(wm1.worst_case_latency, + wm1.consumption_rate); + b.full = rfixed_const(16 * 1000); + priority_mark12.full = rfixed_div(a, b); + } + if (wm0.priority_mark.full > priority_mark02.full) + priority_mark02.full = wm0.priority_mark.full; + if (rfixed_trunc(priority_mark02) < 0) + priority_mark02.full = 0; + if (wm0.priority_mark_max.full > priority_mark02.full) + priority_mark02.full = wm0.priority_mark_max.full; + if (wm1.priority_mark.full > priority_mark12.full) + priority_mark12.full = wm1.priority_mark.full; + if (rfixed_trunc(priority_mark12) < 0) + priority_mark12.full = 0; + if (wm1.priority_mark_max.full > priority_mark12.full) + priority_mark12.full = wm1.priority_mark_max.full; + WREG32(D1MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark02)); + WREG32(D1MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark02)); + WREG32(D2MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark12)); + WREG32(D2MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark12)); + } else if (mode0) { + if (rfixed_trunc(wm0.dbpp) > 64) + a.full = rfixed_mul(wm0.dbpp, wm0.num_line_pair); + else + a.full = wm0.num_line_pair.full; + fill_rate.full = rfixed_div(wm0.sclk, a); + if (wm0.consumption_rate.full > fill_rate.full) { + b.full = wm0.consumption_rate.full - fill_rate.full; + b.full = rfixed_mul(b, wm0.active_time); + a.full = rfixed_mul(wm0.worst_case_latency, + wm0.consumption_rate); + a.full = a.full + b.full; + b.full = rfixed_const(16 * 1000); + priority_mark02.full = rfixed_div(a, b); + } else { + a.full = rfixed_mul(wm0.worst_case_latency, + wm0.consumption_rate); + b.full = rfixed_const(16 * 1000); + priority_mark02.full = rfixed_div(a, b); + } + if (wm0.priority_mark.full > priority_mark02.full) + priority_mark02.full = wm0.priority_mark.full; + if (rfixed_trunc(priority_mark02) < 0) + priority_mark02.full = 0; + if (wm0.priority_mark_max.full > priority_mark02.full) + priority_mark02.full = wm0.priority_mark_max.full; + WREG32(D1MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark02)); + WREG32(D1MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark02)); + WREG32(D2MODE_PRIORITY_A_CNT, MODE_PRIORITY_OFF); + WREG32(D2MODE_PRIORITY_B_CNT, MODE_PRIORITY_OFF); + } else { + if (rfixed_trunc(wm1.dbpp) > 64) + a.full = rfixed_mul(wm1.dbpp, wm1.num_line_pair); + else + a.full = wm1.num_line_pair.full; + fill_rate.full = rfixed_div(wm1.sclk, a); + if (wm1.consumption_rate.full > fill_rate.full) { + b.full = wm1.consumption_rate.full - fill_rate.full; + b.full = rfixed_mul(b, wm1.active_time); + a.full = rfixed_mul(wm1.worst_case_latency, + wm1.consumption_rate); + a.full = a.full + b.full; + b.full = rfixed_const(16 * 1000); + priority_mark12.full = rfixed_div(a, b); + } else { + a.full = rfixed_mul(wm1.worst_case_latency, + wm1.consumption_rate); + b.full = rfixed_const(16 * 1000); + priority_mark12.full = rfixed_div(a, b); + } + if (wm1.priority_mark.full > priority_mark12.full) + priority_mark12.full = wm1.priority_mark.full; + if (rfixed_trunc(priority_mark12) < 0) + priority_mark12.full = 0; + if (wm1.priority_mark_max.full > priority_mark12.full) + priority_mark12.full = wm1.priority_mark_max.full; + WREG32(D1MODE_PRIORITY_A_CNT, MODE_PRIORITY_OFF); + WREG32(D1MODE_PRIORITY_B_CNT, MODE_PRIORITY_OFF); + WREG32(D2MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark12)); + WREG32(D2MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark12)); + } +} /* * Indirect registers accessor diff --git a/drivers/gpu/drm/radeon/rs690r.h b/drivers/gpu/drm/radeon/rs690r.h new file mode 100644 index 00000000000..c0d9faa2175 --- /dev/null +++ b/drivers/gpu/drm/radeon/rs690r.h @@ -0,0 +1,99 @@ +/* + * Copyright 2008 Advanced Micro Devices, Inc. + * Copyright 2008 Red Hat Inc. + * Copyright 2009 Jerome Glisse. + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the "Software"), + * to deal in the Software without restriction, including without limitation + * the rights to use, copy, modify, merge, publish, distribute, sublicense, + * and/or sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR + * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, + * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + * + * Authors: Dave Airlie + * Alex Deucher + * Jerome Glisse + */ +#ifndef RS690R_H +#define RS690R_H + +/* RS690/RS740 registers */ +#define MC_INDEX 0x0078 +# define MC_INDEX_MASK 0x1FF +# define MC_INDEX_WR_EN (1 << 9) +# define MC_INDEX_WR_ACK 0x7F +#define MC_DATA 0x007C +#define HDP_FB_LOCATION 0x0134 +#define DC_LB_MEMORY_SPLIT 0x6520 +#define DC_LB_MEMORY_SPLIT_MASK 0x00000003 +#define DC_LB_MEMORY_SPLIT_SHIFT 0 +#define DC_LB_MEMORY_SPLIT_D1HALF_D2HALF 0 +#define DC_LB_MEMORY_SPLIT_D1_3Q_D2_1Q 1 +#define DC_LB_MEMORY_SPLIT_D1_ONLY 2 +#define DC_LB_MEMORY_SPLIT_D1_1Q_D2_3Q 3 +#define DC_LB_MEMORY_SPLIT_SHIFT_MODE (1 << 2) +#define DC_LB_DISP1_END_ADR_SHIFT 4 +#define DC_LB_DISP1_END_ADR_MASK 0x00007FF0 +#define D1MODE_PRIORITY_A_CNT 0x6548 +#define MODE_PRIORITY_MARK_MASK 0x00007FFF +#define MODE_PRIORITY_OFF (1 << 16) +#define MODE_PRIORITY_ALWAYS_ON (1 << 20) +#define MODE_PRIORITY_FORCE_MASK (1 << 24) +#define D1MODE_PRIORITY_B_CNT 0x654C +#define LB_MAX_REQ_OUTSTANDING 0x6D58 +#define LB_D1_MAX_REQ_OUTSTANDING_MASK 0x0000000F +#define LB_D1_MAX_REQ_OUTSTANDING_SHIFT 0 +#define LB_D2_MAX_REQ_OUTSTANDING_MASK 0x000F0000 +#define LB_D2_MAX_REQ_OUTSTANDING_SHIFT 16 +#define DCP_CONTROL 0x6C9C +#define D2MODE_PRIORITY_A_CNT 0x6D48 +#define D2MODE_PRIORITY_B_CNT 0x6D4C + +/* MC indirect registers */ +#define MC_STATUS_IDLE (1 << 0) +#define MC_MISC_CNTL 0x18 +#define DISABLE_GTW (1 << 1) +#define GART_INDEX_REG_EN (1 << 12) +#define BLOCK_GFX_D3_EN (1 << 14) +#define GART_FEATURE_ID 0x2B +#define HANG_EN (1 << 11) +#define TLB_ENABLE (1 << 18) +#define P2P_ENABLE (1 << 19) +#define GTW_LAC_EN (1 << 25) +#define LEVEL2_GART (0 << 30) +#define LEVEL1_GART (1 << 30) +#define PDC_EN (1 << 31) +#define GART_BASE 0x2C +#define GART_CACHE_CNTRL 0x2E +# define GART_CACHE_INVALIDATE (1 << 0) +#define MC_STATUS 0x90 +#define MCCFG_FB_LOCATION 0x100 +#define MC_FB_START_MASK 0x0000FFFF +#define MC_FB_START_SHIFT 0 +#define MC_FB_TOP_MASK 0xFFFF0000 +#define MC_FB_TOP_SHIFT 16 +#define MCCFG_AGP_LOCATION 0x101 +#define MC_AGP_START_MASK 0x0000FFFF +#define MC_AGP_START_SHIFT 0 +#define MC_AGP_TOP_MASK 0xFFFF0000 +#define MC_AGP_TOP_SHIFT 16 +#define MCCFG_AGP_BASE 0x102 +#define MCCFG_AGP_BASE_2 0x103 +#define MC_INIT_MISC_LAT_TIMER 0x104 +#define MC_DISP0R_INIT_LAT_SHIFT 8 +#define MC_DISP0R_INIT_LAT_MASK 0x00000F00 +#define MC_DISP1R_INIT_LAT_SHIFT 12 +#define MC_DISP1R_INIT_LAT_MASK 0x0000F000 + +#endif diff --git a/drivers/gpu/drm/radeon/rv515.c b/drivers/gpu/drm/radeon/rv515.c index 677929ed8ed..4fd411893b9 100644 --- a/drivers/gpu/drm/radeon/rv515.c +++ b/drivers/gpu/drm/radeon/rv515.c @@ -27,8 +27,9 @@ */ #include #include "drmP.h" -#include "radeon_reg.h" +#include "rv515r.h" #include "radeon.h" +#include "radeon_share.h" /* rv515 depends on : */ void r100_hdp_reset(struct radeon_device *rdev); @@ -100,25 +101,25 @@ int rv515_mc_init(struct radeon_device *rdev) } /* Write VRAM size in case we are limiting it */ WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); - tmp = REG_SET(RV515_MC_FB_START, rdev->mc.vram_location >> 16); + tmp = REG_SET(MC_FB_START, rdev->mc.vram_location >> 16); WREG32(0x134, tmp); tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1; - tmp = REG_SET(RV515_MC_FB_TOP, tmp >> 16); - tmp |= REG_SET(RV515_MC_FB_START, rdev->mc.vram_location >> 16); - WREG32_MC(RV515_MC_FB_LOCATION, tmp); - WREG32(RS690_HDP_FB_LOCATION, rdev->mc.vram_location >> 16); + tmp = REG_SET(MC_FB_TOP, tmp >> 16); + tmp |= REG_SET(MC_FB_START, rdev->mc.vram_location >> 16); + WREG32_MC(MC_FB_LOCATION, tmp); + WREG32(HDP_FB_LOCATION, rdev->mc.vram_location >> 16); WREG32(0x310, rdev->mc.vram_location); if (rdev->flags & RADEON_IS_AGP) { tmp = rdev->mc.gtt_location + rdev->mc.gtt_size - 1; - tmp = REG_SET(RV515_MC_AGP_TOP, tmp >> 16); - tmp |= REG_SET(RV515_MC_AGP_START, rdev->mc.gtt_location >> 16); - WREG32_MC(RV515_MC_AGP_LOCATION, tmp); - WREG32_MC(RV515_MC_AGP_BASE, rdev->mc.agp_base); - WREG32_MC(RV515_MC_AGP_BASE_2, 0); + tmp = REG_SET(MC_AGP_TOP, tmp >> 16); + tmp |= REG_SET(MC_AGP_START, rdev->mc.gtt_location >> 16); + WREG32_MC(MC_AGP_LOCATION, tmp); + WREG32_MC(MC_AGP_BASE, rdev->mc.agp_base); + WREG32_MC(MC_AGP_BASE_2, 0); } else { - WREG32_MC(RV515_MC_AGP_LOCATION, 0x0FFFFFFF); - WREG32_MC(RV515_MC_AGP_BASE, 0); - WREG32_MC(RV515_MC_AGP_BASE_2, 0); + WREG32_MC(MC_AGP_LOCATION, 0x0FFFFFFF); + WREG32_MC(MC_AGP_BASE, 0); + WREG32_MC(MC_AGP_BASE_2, 0); } return 0; } @@ -136,95 +137,67 @@ void rv515_mc_fini(struct radeon_device *rdev) */ void rv515_ring_start(struct radeon_device *rdev) { - unsigned gb_tile_config; int r; - /* Sub pixel 1/12 so we can have 4K rendering according to doc */ - gb_tile_config = R300_ENABLE_TILING | R300_TILE_SIZE_16; - switch (rdev->num_gb_pipes) { - case 2: - gb_tile_config |= R300_PIPE_COUNT_R300; - break; - case 3: - gb_tile_config |= R300_PIPE_COUNT_R420_3P; - break; - case 4: - gb_tile_config |= R300_PIPE_COUNT_R420; - break; - case 1: - default: - gb_tile_config |= R300_PIPE_COUNT_RV350; - break; - } - r = radeon_ring_lock(rdev, 64); if (r) { return; } - radeon_ring_write(rdev, PACKET0(RADEON_ISYNC_CNTL, 0)); - radeon_ring_write(rdev, - RADEON_ISYNC_ANY2D_IDLE3D | - RADEON_ISYNC_ANY3D_IDLE2D | - RADEON_ISYNC_WAIT_IDLEGUI | - RADEON_ISYNC_CPSCRATCH_IDLEGUI); - radeon_ring_write(rdev, PACKET0(R300_GB_TILE_CONFIG, 0)); - radeon_ring_write(rdev, gb_tile_config); - radeon_ring_write(rdev, PACKET0(RADEON_WAIT_UNTIL, 0)); + radeon_ring_write(rdev, PACKET0(ISYNC_CNTL, 0)); radeon_ring_write(rdev, - RADEON_WAIT_2D_IDLECLEAN | - RADEON_WAIT_3D_IDLECLEAN); + ISYNC_ANY2D_IDLE3D | + ISYNC_ANY3D_IDLE2D | + ISYNC_WAIT_IDLEGUI | + ISYNC_CPSCRATCH_IDLEGUI); + radeon_ring_write(rdev, PACKET0(WAIT_UNTIL, 0)); + radeon_ring_write(rdev, WAIT_2D_IDLECLEAN | WAIT_3D_IDLECLEAN); radeon_ring_write(rdev, PACKET0(0x170C, 0)); radeon_ring_write(rdev, 1 << 31); - radeon_ring_write(rdev, PACKET0(R300_GB_SELECT, 0)); + radeon_ring_write(rdev, PACKET0(GB_SELECT, 0)); radeon_ring_write(rdev, 0); - radeon_ring_write(rdev, PACKET0(R300_GB_ENABLE, 0)); + radeon_ring_write(rdev, PACKET0(GB_ENABLE, 0)); radeon_ring_write(rdev, 0); radeon_ring_write(rdev, PACKET0(0x42C8, 0)); radeon_ring_write(rdev, (1 << rdev->num_gb_pipes) - 1); - radeon_ring_write(rdev, PACKET0(R500_VAP_INDEX_OFFSET, 0)); + radeon_ring_write(rdev, PACKET0(VAP_INDEX_OFFSET, 0)); radeon_ring_write(rdev, 0); - radeon_ring_write(rdev, PACKET0(R300_RB3D_DSTCACHE_CTLSTAT, 0)); - radeon_ring_write(rdev, R300_RB3D_DC_FLUSH | R300_RB3D_DC_FREE); - radeon_ring_write(rdev, PACKET0(R300_RB3D_ZCACHE_CTLSTAT, 0)); - radeon_ring_write(rdev, R300_ZC_FLUSH | R300_ZC_FREE); - radeon_ring_write(rdev, PACKET0(RADEON_WAIT_UNTIL, 0)); - radeon_ring_write(rdev, - RADEON_WAIT_2D_IDLECLEAN | - RADEON_WAIT_3D_IDLECLEAN); - radeon_ring_write(rdev, PACKET0(R300_GB_AA_CONFIG, 0)); + radeon_ring_write(rdev, PACKET0(RB3D_DSTCACHE_CTLSTAT, 0)); + radeon_ring_write(rdev, RB3D_DC_FLUSH | RB3D_DC_FREE); + radeon_ring_write(rdev, PACKET0(ZB_ZCACHE_CTLSTAT, 0)); + radeon_ring_write(rdev, ZC_FLUSH | ZC_FREE); + radeon_ring_write(rdev, PACKET0(WAIT_UNTIL, 0)); + radeon_ring_write(rdev, WAIT_2D_IDLECLEAN | WAIT_3D_IDLECLEAN); + radeon_ring_write(rdev, PACKET0(GB_AA_CONFIG, 0)); radeon_ring_write(rdev, 0); - radeon_ring_write(rdev, PACKET0(R300_RB3D_DSTCACHE_CTLSTAT, 0)); - radeon_ring_write(rdev, R300_RB3D_DC_FLUSH | R300_RB3D_DC_FREE); - radeon_ring_write(rdev, PACKET0(R300_RB3D_ZCACHE_CTLSTAT, 0)); - radeon_ring_write(rdev, R300_ZC_FLUSH | R300_ZC_FREE); - radeon_ring_write(rdev, PACKET0(R300_GB_MSPOS0, 0)); - radeon_ring_write(rdev, - ((6 << R300_MS_X0_SHIFT) | - (6 << R300_MS_Y0_SHIFT) | - (6 << R300_MS_X1_SHIFT) | - (6 << R300_MS_Y1_SHIFT) | - (6 << R300_MS_X2_SHIFT) | - (6 << R300_MS_Y2_SHIFT) | - (6 << R300_MSBD0_Y_SHIFT) | - (6 << R300_MSBD0_X_SHIFT))); - radeon_ring_write(rdev, PACKET0(R300_GB_MSPOS1, 0)); - radeon_ring_write(rdev, - ((6 << R300_MS_X3_SHIFT) | - (6 << R300_MS_Y3_SHIFT) | - (6 << R300_MS_X4_SHIFT) | - (6 << R300_MS_Y4_SHIFT) | - (6 << R300_MS_X5_SHIFT) | - (6 << R300_MS_Y5_SHIFT) | - (6 << R300_MSBD1_SHIFT))); - radeon_ring_write(rdev, PACKET0(R300_GA_ENHANCE, 0)); - radeon_ring_write(rdev, R300_GA_DEADLOCK_CNTL | R300_GA_FASTSYNC_CNTL); - radeon_ring_write(rdev, PACKET0(R300_GA_POLY_MODE, 0)); + radeon_ring_write(rdev, PACKET0(RB3D_DSTCACHE_CTLSTAT, 0)); + radeon_ring_write(rdev, RB3D_DC_FLUSH | RB3D_DC_FREE); + radeon_ring_write(rdev, PACKET0(ZB_ZCACHE_CTLSTAT, 0)); + radeon_ring_write(rdev, ZC_FLUSH | ZC_FREE); + radeon_ring_write(rdev, PACKET0(GB_MSPOS0, 0)); radeon_ring_write(rdev, - R300_FRONT_PTYPE_TRIANGE | R300_BACK_PTYPE_TRIANGE); - radeon_ring_write(rdev, PACKET0(R300_GA_ROUND_MODE, 0)); + ((6 << MS_X0_SHIFT) | + (6 << MS_Y0_SHIFT) | + (6 << MS_X1_SHIFT) | + (6 << MS_Y1_SHIFT) | + (6 << MS_X2_SHIFT) | + (6 << MS_Y2_SHIFT) | + (6 << MSBD0_Y_SHIFT) | + (6 << MSBD0_X_SHIFT))); + radeon_ring_write(rdev, PACKET0(GB_MSPOS1, 0)); radeon_ring_write(rdev, - R300_GEOMETRY_ROUND_NEAREST | - R300_COLOR_ROUND_NEAREST); + ((6 << MS_X3_SHIFT) | + (6 << MS_Y3_SHIFT) | + (6 << MS_X4_SHIFT) | + (6 << MS_Y4_SHIFT) | + (6 << MS_X5_SHIFT) | + (6 << MS_Y5_SHIFT) | + (6 << MSBD1_SHIFT))); + radeon_ring_write(rdev, PACKET0(GA_ENHANCE, 0)); + radeon_ring_write(rdev, GA_DEADLOCK_CNTL | GA_FASTSYNC_CNTL); + radeon_ring_write(rdev, PACKET0(GA_POLY_MODE, 0)); + radeon_ring_write(rdev, FRONT_PTYPE_TRIANGE | BACK_PTYPE_TRIANGE); + radeon_ring_write(rdev, PACKET0(GA_ROUND_MODE, 0)); + radeon_ring_write(rdev, GEOMETRY_ROUND_NEAREST | COLOR_ROUND_NEAREST); radeon_ring_write(rdev, PACKET0(0x20C8, 0)); radeon_ring_write(rdev, 0); radeon_ring_unlock_commit(rdev); @@ -242,8 +215,8 @@ int rv515_mc_wait_for_idle(struct radeon_device *rdev) for (i = 0; i < rdev->usec_timeout; i++) { /* read MC_STATUS */ - tmp = RREG32_MC(RV515_MC_STATUS); - if (tmp & RV515_MC_STATUS_IDLE) { + tmp = RREG32_MC(MC_STATUS); + if (tmp & MC_STATUS_IDLE) { return 0; } DRM_UDELAY(1); @@ -291,33 +264,33 @@ int rv515_ga_reset(struct radeon_device *rdev) reinit_cp = rdev->cp.ready; rdev->cp.ready = false; for (i = 0; i < rdev->usec_timeout; i++) { - WREG32(RADEON_CP_CSQ_MODE, 0); - WREG32(RADEON_CP_CSQ_CNTL, 0); - WREG32(RADEON_RBBM_SOFT_RESET, 0x32005); - (void)RREG32(RADEON_RBBM_SOFT_RESET); + WREG32(CP_CSQ_MODE, 0); + WREG32(CP_CSQ_CNTL, 0); + WREG32(RBBM_SOFT_RESET, 0x32005); + (void)RREG32(RBBM_SOFT_RESET); udelay(200); - WREG32(RADEON_RBBM_SOFT_RESET, 0); + WREG32(RBBM_SOFT_RESET, 0); /* Wait to prevent race in RBBM_STATUS */ mdelay(1); - tmp = RREG32(RADEON_RBBM_STATUS); + tmp = RREG32(RBBM_STATUS); if (tmp & ((1 << 20) | (1 << 26))) { DRM_ERROR("VAP & CP still busy (RBBM_STATUS=0x%08X)\n", tmp); /* GA still busy soft reset it */ WREG32(0x429C, 0x200); - WREG32(R300_VAP_PVS_STATE_FLUSH_REG, 0); + WREG32(VAP_PVS_STATE_FLUSH_REG, 0); WREG32(0x43E0, 0); WREG32(0x43E4, 0); WREG32(0x24AC, 0); } /* Wait to prevent race in RBBM_STATUS */ mdelay(1); - tmp = RREG32(RADEON_RBBM_STATUS); + tmp = RREG32(RBBM_STATUS); if (!(tmp & ((1 << 20) | (1 << 26)))) { break; } } for (i = 0; i < rdev->usec_timeout; i++) { - tmp = RREG32(RADEON_RBBM_STATUS); + tmp = RREG32(RBBM_STATUS); if (!(tmp & ((1 << 20) | (1 << 26)))) { DRM_INFO("GA reset succeed (RBBM_STATUS=0x%08X)\n", tmp); @@ -331,7 +304,7 @@ int rv515_ga_reset(struct radeon_device *rdev) } DRM_UDELAY(1); } - tmp = RREG32(RADEON_RBBM_STATUS); + tmp = RREG32(RBBM_STATUS); DRM_ERROR("Failed to reset GA ! (RBBM_STATUS=0x%08X)\n", tmp); return -1; } @@ -341,7 +314,7 @@ int rv515_gpu_reset(struct radeon_device *rdev) uint32_t status; /* reset order likely matter */ - status = RREG32(RADEON_RBBM_STATUS); + status = RREG32(RBBM_STATUS); /* reset HDP */ r100_hdp_reset(rdev); /* reset rb2d */ @@ -353,12 +326,12 @@ int rv515_gpu_reset(struct radeon_device *rdev) rv515_ga_reset(rdev); } /* reset CP */ - status = RREG32(RADEON_RBBM_STATUS); + status = RREG32(RBBM_STATUS); if (status & (1 << 16)) { r100_cp_reset(rdev); } /* Check if GPU is idle */ - status = RREG32(RADEON_RBBM_STATUS); + status = RREG32(RBBM_STATUS); if (status & (1 << 31)) { DRM_ERROR("Failed to reset GPU (RBBM_STATUS=0x%08X)\n", status); return -1; @@ -377,8 +350,7 @@ static void rv515_vram_get_type(struct radeon_device *rdev) rdev->mc.vram_width = 128; rdev->mc.vram_is_ddr = true; - tmp = RREG32_MC(RV515_MC_CNTL); - tmp &= RV515_MEM_NUM_CHANNELS_MASK; + tmp = RREG32_MC(RV515_MC_CNTL) & MEM_NUM_CHANNELS_MASK; switch (tmp) { case 0: rdev->mc.vram_width = 64; @@ -394,9 +366,19 @@ static void rv515_vram_get_type(struct radeon_device *rdev) void rv515_vram_info(struct radeon_device *rdev) { + fixed20_12 a; + rv515_vram_get_type(rdev); - - r100_vram_init_sizes(rdev); + rdev->mc.vram_size = RREG32(CONFIG_MEMSIZE); + + rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); + rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); + /* FIXME: we should enforce default clock in case GPU is not in + * default setup + */ + a.full = rfixed_const(100); + rdev->pm.sclk.full = rfixed_const(rdev->clock.default_sclk); + rdev->pm.sclk.full = rfixed_div(rdev->pm.sclk, a); } @@ -407,35 +389,35 @@ uint32_t rv515_mc_rreg(struct radeon_device *rdev, uint32_t reg) { uint32_t r; - WREG32(R520_MC_IND_INDEX, 0x7f0000 | (reg & 0xffff)); - r = RREG32(R520_MC_IND_DATA); - WREG32(R520_MC_IND_INDEX, 0); + WREG32(MC_IND_INDEX, 0x7f0000 | (reg & 0xffff)); + r = RREG32(MC_IND_DATA); + WREG32(MC_IND_INDEX, 0); return r; } void rv515_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) { - WREG32(R520_MC_IND_INDEX, 0xff0000 | ((reg) & 0xffff)); - WREG32(R520_MC_IND_DATA, (v)); - WREG32(R520_MC_IND_INDEX, 0); + WREG32(MC_IND_INDEX, 0xff0000 | ((reg) & 0xffff)); + WREG32(MC_IND_DATA, (v)); + WREG32(MC_IND_INDEX, 0); } uint32_t rv515_pcie_rreg(struct radeon_device *rdev, uint32_t reg) { uint32_t r; - WREG32(RADEON_PCIE_INDEX, ((reg) & 0x7ff)); - (void)RREG32(RADEON_PCIE_INDEX); - r = RREG32(RADEON_PCIE_DATA); + WREG32(PCIE_INDEX, ((reg) & 0x7ff)); + (void)RREG32(PCIE_INDEX); + r = RREG32(PCIE_DATA); return r; } void rv515_pcie_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) { - WREG32(RADEON_PCIE_INDEX, ((reg) & 0x7ff)); - (void)RREG32(RADEON_PCIE_INDEX); - WREG32(RADEON_PCIE_DATA, (v)); - (void)RREG32(RADEON_PCIE_DATA); + WREG32(PCIE_INDEX, ((reg) & 0x7ff)); + (void)RREG32(PCIE_INDEX); + WREG32(PCIE_DATA, (v)); + (void)RREG32(PCIE_DATA); } @@ -450,13 +432,13 @@ static int rv515_debugfs_pipes_info(struct seq_file *m, void *data) struct radeon_device *rdev = dev->dev_private; uint32_t tmp; - tmp = RREG32(R400_GB_PIPE_SELECT); + tmp = RREG32(GB_PIPE_SELECT); seq_printf(m, "GB_PIPE_SELECT 0x%08x\n", tmp); - tmp = RREG32(R500_SU_REG_DEST); + tmp = RREG32(SU_REG_DEST); seq_printf(m, "SU_REG_DEST 0x%08x\n", tmp); - tmp = RREG32(R300_GB_TILE_CONFIG); + tmp = RREG32(GB_TILE_CONFIG); seq_printf(m, "GB_TILE_CONFIG 0x%08x\n", tmp); - tmp = RREG32(R300_DST_PIPE_CONFIG); + tmp = RREG32(DST_PIPE_CONFIG); seq_printf(m, "DST_PIPE_CONFIG 0x%08x\n", tmp); return 0; } @@ -571,3 +553,551 @@ int rv515_init(struct radeon_device *rdev) rdev->config.r300.reg_safe_bm_size = ARRAY_SIZE(r500_reg_safe_bm); return 0; } + +void atom_rv515_force_tv_scaler(struct radeon_device *rdev) +{ + + WREG32(0x659C, 0x0); + WREG32(0x6594, 0x705); + WREG32(0x65A4, 0x10001); + WREG32(0x65D8, 0x0); + WREG32(0x65B0, 0x0); + WREG32(0x65C0, 0x0); + WREG32(0x65D4, 0x0); + WREG32(0x6578, 0x0); + WREG32(0x657C, 0x841880A8); + WREG32(0x6578, 0x1); + WREG32(0x657C, 0x84208680); + WREG32(0x6578, 0x2); + WREG32(0x657C, 0xBFF880B0); + WREG32(0x6578, 0x100); + WREG32(0x657C, 0x83D88088); + WREG32(0x6578, 0x101); + WREG32(0x657C, 0x84608680); + WREG32(0x6578, 0x102); + WREG32(0x657C, 0xBFF080D0); + WREG32(0x6578, 0x200); + WREG32(0x657C, 0x83988068); + WREG32(0x6578, 0x201); + WREG32(0x657C, 0x84A08680); + WREG32(0x6578, 0x202); + WREG32(0x657C, 0xBFF080F8); + WREG32(0x6578, 0x300); + WREG32(0x657C, 0x83588058); + WREG32(0x6578, 0x301); + WREG32(0x657C, 0x84E08660); + WREG32(0x6578, 0x302); + WREG32(0x657C, 0xBFF88120); + WREG32(0x6578, 0x400); + WREG32(0x657C, 0x83188040); + WREG32(0x6578, 0x401); + WREG32(0x657C, 0x85008660); + WREG32(0x6578, 0x402); + WREG32(0x657C, 0xBFF88150); + WREG32(0x6578, 0x500); + WREG32(0x657C, 0x82D88030); + WREG32(0x6578, 0x501); + WREG32(0x657C, 0x85408640); + WREG32(0x6578, 0x502); + WREG32(0x657C, 0xBFF88180); + WREG32(0x6578, 0x600); + WREG32(0x657C, 0x82A08018); + WREG32(0x6578, 0x601); + WREG32(0x657C, 0x85808620); + WREG32(0x6578, 0x602); + WREG32(0x657C, 0xBFF081B8); + WREG32(0x6578, 0x700); + WREG32(0x657C, 0x82608010); + WREG32(0x6578, 0x701); + WREG32(0x657C, 0x85A08600); + WREG32(0x6578, 0x702); + WREG32(0x657C, 0x800081F0); + WREG32(0x6578, 0x800); + WREG32(0x657C, 0x8228BFF8); + WREG32(0x6578, 0x801); + WREG32(0x657C, 0x85E085E0); + WREG32(0x6578, 0x802); + WREG32(0x657C, 0xBFF88228); + WREG32(0x6578, 0x10000); + WREG32(0x657C, 0x82A8BF00); + WREG32(0x6578, 0x10001); + WREG32(0x657C, 0x82A08CC0); + WREG32(0x6578, 0x10002); + WREG32(0x657C, 0x8008BEF8); + WREG32(0x6578, 0x10100); + WREG32(0x657C, 0x81F0BF28); + WREG32(0x6578, 0x10101); + WREG32(0x657C, 0x83608CA0); + WREG32(0x6578, 0x10102); + WREG32(0x657C, 0x8018BED0); + WREG32(0x6578, 0x10200); + WREG32(0x657C, 0x8148BF38); + WREG32(0x6578, 0x10201); + WREG32(0x657C, 0x84408C80); + WREG32(0x6578, 0x10202); + WREG32(0x657C, 0x8008BEB8); + WREG32(0x6578, 0x10300); + WREG32(0x657C, 0x80B0BF78); + WREG32(0x6578, 0x10301); + WREG32(0x657C, 0x85008C20); + WREG32(0x6578, 0x10302); + WREG32(0x657C, 0x8020BEA0); + WREG32(0x6578, 0x10400); + WREG32(0x657C, 0x8028BF90); + WREG32(0x6578, 0x10401); + WREG32(0x657C, 0x85E08BC0); + WREG32(0x6578, 0x10402); + WREG32(0x657C, 0x8018BE90); + WREG32(0x6578, 0x10500); + WREG32(0x657C, 0xBFB8BFB0); + WREG32(0x6578, 0x10501); + WREG32(0x657C, 0x86C08B40); + WREG32(0x6578, 0x10502); + WREG32(0x657C, 0x8010BE90); + WREG32(0x6578, 0x10600); + WREG32(0x657C, 0xBF58BFC8); + WREG32(0x6578, 0x10601); + WREG32(0x657C, 0x87A08AA0); + WREG32(0x6578, 0x10602); + WREG32(0x657C, 0x8010BE98); + WREG32(0x6578, 0x10700); + WREG32(0x657C, 0xBF10BFF0); + WREG32(0x6578, 0x10701); + WREG32(0x657C, 0x886089E0); + WREG32(0x6578, 0x10702); + WREG32(0x657C, 0x8018BEB0); + WREG32(0x6578, 0x10800); + WREG32(0x657C, 0xBED8BFE8); + WREG32(0x6578, 0x10801); + WREG32(0x657C, 0x89408940); + WREG32(0x6578, 0x10802); + WREG32(0x657C, 0xBFE8BED8); + WREG32(0x6578, 0x20000); + WREG32(0x657C, 0x80008000); + WREG32(0x6578, 0x20001); + WREG32(0x657C, 0x90008000); + WREG32(0x6578, 0x20002); + WREG32(0x657C, 0x80008000); + WREG32(0x6578, 0x20003); + WREG32(0x657C, 0x80008000); + WREG32(0x6578, 0x20100); + WREG32(0x657C, 0x80108000); + WREG32(0x6578, 0x20101); + WREG32(0x657C, 0x8FE0BF70); + WREG32(0x6578, 0x20102); + WREG32(0x657C, 0xBFE880C0); + WREG32(0x6578, 0x20103); + WREG32(0x657C, 0x80008000); + WREG32(0x6578, 0x20200); + WREG32(0x657C, 0x8018BFF8); + WREG32(0x6578, 0x20201); + WREG32(0x657C, 0x8F80BF08); + WREG32(0x6578, 0x20202); + WREG32(0x657C, 0xBFD081A0); + WREG32(0x6578, 0x20203); + WREG32(0x657C, 0xBFF88000); + WREG32(0x6578, 0x20300); + WREG32(0x657C, 0x80188000); + WREG32(0x6578, 0x20301); + WREG32(0x657C, 0x8EE0BEC0); + WREG32(0x6578, 0x20302); + WREG32(0x657C, 0xBFB082A0); + WREG32(0x6578, 0x20303); + WREG32(0x657C, 0x80008000); + WREG32(0x6578, 0x20400); + WREG32(0x657C, 0x80188000); + WREG32(0x6578, 0x20401); + WREG32(0x657C, 0x8E00BEA0); + WREG32(0x6578, 0x20402); + WREG32(0x657C, 0xBF8883C0); + WREG32(0x6578, 0x20403); + WREG32(0x657C, 0x80008000); + WREG32(0x6578, 0x20500); + WREG32(0x657C, 0x80188000); + WREG32(0x6578, 0x20501); + WREG32(0x657C, 0x8D00BE90); + WREG32(0x6578, 0x20502); + WREG32(0x657C, 0xBF588500); + WREG32(0x6578, 0x20503); + WREG32(0x657C, 0x80008008); + WREG32(0x6578, 0x20600); + WREG32(0x657C, 0x80188000); + WREG32(0x6578, 0x20601); + WREG32(0x657C, 0x8BC0BE98); + WREG32(0x6578, 0x20602); + WREG32(0x657C, 0xBF308660); + WREG32(0x6578, 0x20603); + WREG32(0x657C, 0x80008008); + WREG32(0x6578, 0x20700); + WREG32(0x657C, 0x80108000); + WREG32(0x6578, 0x20701); + WREG32(0x657C, 0x8A80BEB0); + WREG32(0x6578, 0x20702); + WREG32(0x657C, 0xBF0087C0); + WREG32(0x6578, 0x20703); + WREG32(0x657C, 0x80008008); + WREG32(0x6578, 0x20800); + WREG32(0x657C, 0x80108000); + WREG32(0x6578, 0x20801); + WREG32(0x657C, 0x8920BED0); + WREG32(0x6578, 0x20802); + WREG32(0x657C, 0xBED08920); + WREG32(0x6578, 0x20803); + WREG32(0x657C, 0x80008010); + WREG32(0x6578, 0x30000); + WREG32(0x657C, 0x90008000); + WREG32(0x6578, 0x30001); + WREG32(0x657C, 0x80008000); + WREG32(0x6578, 0x30100); + WREG32(0x657C, 0x8FE0BF90); + WREG32(0x6578, 0x30101); + WREG32(0x657C, 0xBFF880A0); + WREG32(0x6578, 0x30200); + WREG32(0x657C, 0x8F60BF40); + WREG32(0x6578, 0x30201); + WREG32(0x657C, 0xBFE88180); + WREG32(0x6578, 0x30300); + WREG32(0x657C, 0x8EC0BF00); + WREG32(0x6578, 0x30301); + WREG32(0x657C, 0xBFC88280); + WREG32(0x6578, 0x30400); + WREG32(0x657C, 0x8DE0BEE0); + WREG32(0x6578, 0x30401); + WREG32(0x657C, 0xBFA083A0); + WREG32(0x6578, 0x30500); + WREG32(0x657C, 0x8CE0BED0); + WREG32(0x6578, 0x30501); + WREG32(0x657C, 0xBF7884E0); + WREG32(0x6578, 0x30600); + WREG32(0x657C, 0x8BA0BED8); + WREG32(0x6578, 0x30601); + WREG32(0x657C, 0xBF508640); + WREG32(0x6578, 0x30700); + WREG32(0x657C, 0x8A60BEE8); + WREG32(0x6578, 0x30701); + WREG32(0x657C, 0xBF2087A0); + WREG32(0x6578, 0x30800); + WREG32(0x657C, 0x8900BF00); + WREG32(0x6578, 0x30801); + WREG32(0x657C, 0xBF008900); +} + +struct rv515_watermark { + u32 lb_request_fifo_depth; + fixed20_12 num_line_pair; + fixed20_12 estimated_width; + fixed20_12 worst_case_latency; + fixed20_12 consumption_rate; + fixed20_12 active_time; + fixed20_12 dbpp; + fixed20_12 priority_mark_max; + fixed20_12 priority_mark; + fixed20_12 sclk; +}; + +void rv515_crtc_bandwidth_compute(struct radeon_device *rdev, + struct radeon_crtc *crtc, + struct rv515_watermark *wm) +{ + struct drm_display_mode *mode = &crtc->base.mode; + fixed20_12 a, b, c; + fixed20_12 pclk, request_fifo_depth, tolerable_latency, estimated_width; + fixed20_12 consumption_time, line_time, chunk_time, read_delay_latency; + + if (!crtc->base.enabled) { + /* FIXME: wouldn't it better to set priority mark to maximum */ + wm->lb_request_fifo_depth = 4; + return; + } + + if (crtc->vsc.full > rfixed_const(2)) + wm->num_line_pair.full = rfixed_const(2); + else + wm->num_line_pair.full = rfixed_const(1); + + b.full = rfixed_const(mode->crtc_hdisplay); + c.full = rfixed_const(256); + a.full = rfixed_mul(wm->num_line_pair, b); + request_fifo_depth.full = rfixed_div(a, c); + if (a.full < rfixed_const(4)) { + wm->lb_request_fifo_depth = 4; + } else { + wm->lb_request_fifo_depth = rfixed_trunc(request_fifo_depth); + } + + /* Determine consumption rate + * pclk = pixel clock period(ns) = 1000 / (mode.clock / 1000) + * vtaps = number of vertical taps, + * vsc = vertical scaling ratio, defined as source/destination + * hsc = horizontal scaling ration, defined as source/destination + */ + a.full = rfixed_const(mode->clock); + b.full = rfixed_const(1000); + a.full = rfixed_div(a, b); + pclk.full = rfixed_div(b, a); + if (crtc->rmx_type != RMX_OFF) { + b.full = rfixed_const(2); + if (crtc->vsc.full > b.full) + b.full = crtc->vsc.full; + b.full = rfixed_mul(b, crtc->hsc); + c.full = rfixed_const(2); + b.full = rfixed_div(b, c); + consumption_time.full = rfixed_div(pclk, b); + } else { + consumption_time.full = pclk.full; + } + a.full = rfixed_const(1); + wm->consumption_rate.full = rfixed_div(a, consumption_time); + + + /* Determine line time + * LineTime = total time for one line of displayhtotal + * LineTime = total number of horizontal pixels + * pclk = pixel clock period(ns) + */ + a.full = rfixed_const(crtc->base.mode.crtc_htotal); + line_time.full = rfixed_mul(a, pclk); + + /* Determine active time + * ActiveTime = time of active region of display within one line, + * hactive = total number of horizontal active pixels + * htotal = total number of horizontal pixels + */ + a.full = rfixed_const(crtc->base.mode.crtc_htotal); + b.full = rfixed_const(crtc->base.mode.crtc_hdisplay); + wm->active_time.full = rfixed_mul(line_time, b); + wm->active_time.full = rfixed_div(wm->active_time, a); + + /* Determine chunk time + * ChunkTime = the time it takes the DCP to send one chunk of data + * to the LB which consists of pipeline delay and inter chunk gap + * sclk = system clock(Mhz) + */ + a.full = rfixed_const(600 * 1000); + chunk_time.full = rfixed_div(a, rdev->pm.sclk); + read_delay_latency.full = rfixed_const(1000); + + /* Determine the worst case latency + * NumLinePair = Number of line pairs to request(1=2 lines, 2=4 lines) + * WorstCaseLatency = worst case time from urgent to when the MC starts + * to return data + * READ_DELAY_IDLE_MAX = constant of 1us + * ChunkTime = time it takes the DCP to send one chunk of data to the LB + * which consists of pipeline delay and inter chunk gap + */ + if (rfixed_trunc(wm->num_line_pair) > 1) { + a.full = rfixed_const(3); + wm->worst_case_latency.full = rfixed_mul(a, chunk_time); + wm->worst_case_latency.full += read_delay_latency.full; + } else { + wm->worst_case_latency.full = chunk_time.full + read_delay_latency.full; + } + + /* Determine the tolerable latency + * TolerableLatency = Any given request has only 1 line time + * for the data to be returned + * LBRequestFifoDepth = Number of chunk requests the LB can + * put into the request FIFO for a display + * LineTime = total time for one line of display + * ChunkTime = the time it takes the DCP to send one chunk + * of data to the LB which consists of + * pipeline delay and inter chunk gap + */ + if ((2+wm->lb_request_fifo_depth) >= rfixed_trunc(request_fifo_depth)) { + tolerable_latency.full = line_time.full; + } else { + tolerable_latency.full = rfixed_const(wm->lb_request_fifo_depth - 2); + tolerable_latency.full = request_fifo_depth.full - tolerable_latency.full; + tolerable_latency.full = rfixed_mul(tolerable_latency, chunk_time); + tolerable_latency.full = line_time.full - tolerable_latency.full; + } + /* We assume worst case 32bits (4 bytes) */ + wm->dbpp.full = rfixed_const(2 * 16); + + /* Determine the maximum priority mark + * width = viewport width in pixels + */ + a.full = rfixed_const(16); + wm->priority_mark_max.full = rfixed_const(crtc->base.mode.crtc_hdisplay); + wm->priority_mark_max.full = rfixed_div(wm->priority_mark_max, a); + + /* Determine estimated width */ + estimated_width.full = tolerable_latency.full - wm->worst_case_latency.full; + estimated_width.full = rfixed_div(estimated_width, consumption_time); + if (rfixed_trunc(estimated_width) > crtc->base.mode.crtc_hdisplay) { + wm->priority_mark.full = rfixed_const(10); + } else { + a.full = rfixed_const(16); + wm->priority_mark.full = rfixed_div(estimated_width, a); + wm->priority_mark.full = wm->priority_mark_max.full - wm->priority_mark.full; + } +} + +void rv515_bandwidth_avivo_update(struct radeon_device *rdev) +{ + struct drm_display_mode *mode0 = NULL; + struct drm_display_mode *mode1 = NULL; + struct rv515_watermark wm0; + struct rv515_watermark wm1; + u32 tmp; + fixed20_12 priority_mark02, priority_mark12, fill_rate; + fixed20_12 a, b; + + if (rdev->mode_info.crtcs[0]->base.enabled) + mode0 = &rdev->mode_info.crtcs[0]->base.mode; + if (rdev->mode_info.crtcs[1]->base.enabled) + mode1 = &rdev->mode_info.crtcs[1]->base.mode; + rs690_line_buffer_adjust(rdev, mode0, mode1); + + rv515_crtc_bandwidth_compute(rdev, rdev->mode_info.crtcs[0], &wm0); + rv515_crtc_bandwidth_compute(rdev, rdev->mode_info.crtcs[1], &wm1); + + tmp = wm0.lb_request_fifo_depth; + tmp |= wm1.lb_request_fifo_depth << 16; + WREG32(LB_MAX_REQ_OUTSTANDING, tmp); + + if (mode0 && mode1) { + if (rfixed_trunc(wm0.dbpp) > 64) + a.full = rfixed_div(wm0.dbpp, wm0.num_line_pair); + else + a.full = wm0.num_line_pair.full; + if (rfixed_trunc(wm1.dbpp) > 64) + b.full = rfixed_div(wm1.dbpp, wm1.num_line_pair); + else + b.full = wm1.num_line_pair.full; + a.full += b.full; + fill_rate.full = rfixed_div(wm0.sclk, a); + if (wm0.consumption_rate.full > fill_rate.full) { + b.full = wm0.consumption_rate.full - fill_rate.full; + b.full = rfixed_mul(b, wm0.active_time); + a.full = rfixed_const(16); + b.full = rfixed_div(b, a); + a.full = rfixed_mul(wm0.worst_case_latency, + wm0.consumption_rate); + priority_mark02.full = a.full + b.full; + } else { + a.full = rfixed_mul(wm0.worst_case_latency, + wm0.consumption_rate); + b.full = rfixed_const(16 * 1000); + priority_mark02.full = rfixed_div(a, b); + } + if (wm1.consumption_rate.full > fill_rate.full) { + b.full = wm1.consumption_rate.full - fill_rate.full; + b.full = rfixed_mul(b, wm1.active_time); + a.full = rfixed_const(16); + b.full = rfixed_div(b, a); + a.full = rfixed_mul(wm1.worst_case_latency, + wm1.consumption_rate); + priority_mark12.full = a.full + b.full; + } else { + a.full = rfixed_mul(wm1.worst_case_latency, + wm1.consumption_rate); + b.full = rfixed_const(16 * 1000); + priority_mark12.full = rfixed_div(a, b); + } + if (wm0.priority_mark.full > priority_mark02.full) + priority_mark02.full = wm0.priority_mark.full; + if (rfixed_trunc(priority_mark02) < 0) + priority_mark02.full = 0; + if (wm0.priority_mark_max.full > priority_mark02.full) + priority_mark02.full = wm0.priority_mark_max.full; + if (wm1.priority_mark.full > priority_mark12.full) + priority_mark12.full = wm1.priority_mark.full; + if (rfixed_trunc(priority_mark12) < 0) + priority_mark12.full = 0; + if (wm1.priority_mark_max.full > priority_mark12.full) + priority_mark12.full = wm1.priority_mark_max.full; + WREG32(D1MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark02)); + WREG32(D1MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark02)); + WREG32(D2MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark12)); + WREG32(D2MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark12)); + } else if (mode0) { + if (rfixed_trunc(wm0.dbpp) > 64) + a.full = rfixed_div(wm0.dbpp, wm0.num_line_pair); + else + a.full = wm0.num_line_pair.full; + fill_rate.full = rfixed_div(wm0.sclk, a); + if (wm0.consumption_rate.full > fill_rate.full) { + b.full = wm0.consumption_rate.full - fill_rate.full; + b.full = rfixed_mul(b, wm0.active_time); + a.full = rfixed_const(16); + b.full = rfixed_div(b, a); + a.full = rfixed_mul(wm0.worst_case_latency, + wm0.consumption_rate); + priority_mark02.full = a.full + b.full; + } else { + a.full = rfixed_mul(wm0.worst_case_latency, + wm0.consumption_rate); + b.full = rfixed_const(16); + priority_mark02.full = rfixed_div(a, b); + } + if (wm0.priority_mark.full > priority_mark02.full) + priority_mark02.full = wm0.priority_mark.full; + if (rfixed_trunc(priority_mark02) < 0) + priority_mark02.full = 0; + if (wm0.priority_mark_max.full > priority_mark02.full) + priority_mark02.full = wm0.priority_mark_max.full; + WREG32(D1MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark02)); + WREG32(D1MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark02)); + WREG32(D2MODE_PRIORITY_A_CNT, MODE_PRIORITY_OFF); + WREG32(D2MODE_PRIORITY_B_CNT, MODE_PRIORITY_OFF); + } else { + if (rfixed_trunc(wm1.dbpp) > 64) + a.full = rfixed_div(wm1.dbpp, wm1.num_line_pair); + else + a.full = wm1.num_line_pair.full; + fill_rate.full = rfixed_div(wm1.sclk, a); + if (wm1.consumption_rate.full > fill_rate.full) { + b.full = wm1.consumption_rate.full - fill_rate.full; + b.full = rfixed_mul(b, wm1.active_time); + a.full = rfixed_const(16); + b.full = rfixed_div(b, a); + a.full = rfixed_mul(wm1.worst_case_latency, + wm1.consumption_rate); + priority_mark12.full = a.full + b.full; + } else { + a.full = rfixed_mul(wm1.worst_case_latency, + wm1.consumption_rate); + b.full = rfixed_const(16 * 1000); + priority_mark12.full = rfixed_div(a, b); + } + if (wm1.priority_mark.full > priority_mark12.full) + priority_mark12.full = wm1.priority_mark.full; + if (rfixed_trunc(priority_mark12) < 0) + priority_mark12.full = 0; + if (wm1.priority_mark_max.full > priority_mark12.full) + priority_mark12.full = wm1.priority_mark_max.full; + WREG32(D1MODE_PRIORITY_A_CNT, MODE_PRIORITY_OFF); + WREG32(D1MODE_PRIORITY_B_CNT, MODE_PRIORITY_OFF); + WREG32(D2MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark12)); + WREG32(D2MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark12)); + } +} + +void rv515_bandwidth_update(struct radeon_device *rdev) +{ + uint32_t tmp; + struct drm_display_mode *mode0 = NULL; + struct drm_display_mode *mode1 = NULL; + + if (rdev->mode_info.crtcs[0]->base.enabled) + mode0 = &rdev->mode_info.crtcs[0]->base.mode; + if (rdev->mode_info.crtcs[1]->base.enabled) + mode1 = &rdev->mode_info.crtcs[1]->base.mode; + /* + * Set display0/1 priority up in the memory controller for + * modes if the user specifies HIGH for displaypriority + * option. + */ + if (rdev->disp_priority == 2) { + tmp = RREG32_MC(MC_MISC_LAT_TIMER); + tmp &= ~MC_DISP1R_INIT_LAT_MASK; + tmp &= ~MC_DISP0R_INIT_LAT_MASK; + if (mode1) + tmp |= (1 << MC_DISP1R_INIT_LAT_SHIFT); + if (mode0) + tmp |= (1 << MC_DISP0R_INIT_LAT_SHIFT); + WREG32_MC(MC_MISC_LAT_TIMER, tmp); + } + rv515_bandwidth_avivo_update(rdev); +} diff --git a/drivers/gpu/drm/radeon/rv515r.h b/drivers/gpu/drm/radeon/rv515r.h new file mode 100644 index 00000000000..f3cf8403990 --- /dev/null +++ b/drivers/gpu/drm/radeon/rv515r.h @@ -0,0 +1,170 @@ +/* + * Copyright 2008 Advanced Micro Devices, Inc. + * Copyright 2008 Red Hat Inc. + * Copyright 2009 Jerome Glisse. + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the "Software"), + * to deal in the Software without restriction, including without limitation + * the rights to use, copy, modify, merge, publish, distribute, sublicense, + * and/or sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR + * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, + * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + * + * Authors: Dave Airlie + * Alex Deucher + * Jerome Glisse + */ +#ifndef RV515R_H +#define RV515R_H + +/* RV515 registers */ +#define PCIE_INDEX 0x0030 +#define PCIE_DATA 0x0034 +#define MC_IND_INDEX 0x0070 +#define MC_IND_WR_EN (1 << 24) +#define MC_IND_DATA 0x0074 +#define RBBM_SOFT_RESET 0x00F0 +#define CONFIG_MEMSIZE 0x00F8 +#define HDP_FB_LOCATION 0x0134 +#define CP_CSQ_CNTL 0x0740 +#define CP_CSQ_MODE 0x0744 +#define CP_CSQ_ADDR 0x07F0 +#define CP_CSQ_DATA 0x07F4 +#define CP_CSQ_STAT 0x07F8 +#define CP_CSQ2_STAT 0x07FC +#define RBBM_STATUS 0x0E40 +#define DST_PIPE_CONFIG 0x170C +#define WAIT_UNTIL 0x1720 +#define WAIT_2D_IDLE (1 << 14) +#define WAIT_3D_IDLE (1 << 15) +#define WAIT_2D_IDLECLEAN (1 << 16) +#define WAIT_3D_IDLECLEAN (1 << 17) +#define ISYNC_CNTL 0x1724 +#define ISYNC_ANY2D_IDLE3D (1 << 0) +#define ISYNC_ANY3D_IDLE2D (1 << 1) +#define ISYNC_TRIG2D_IDLE3D (1 << 2) +#define ISYNC_TRIG3D_IDLE2D (1 << 3) +#define ISYNC_WAIT_IDLEGUI (1 << 4) +#define ISYNC_CPSCRATCH_IDLEGUI (1 << 5) +#define VAP_INDEX_OFFSET 0x208C +#define VAP_PVS_STATE_FLUSH_REG 0x2284 +#define GB_ENABLE 0x4008 +#define GB_MSPOS0 0x4010 +#define MS_X0_SHIFT 0 +#define MS_Y0_SHIFT 4 +#define MS_X1_SHIFT 8 +#define MS_Y1_SHIFT 12 +#define MS_X2_SHIFT 16 +#define MS_Y2_SHIFT 20 +#define MSBD0_Y_SHIFT 24 +#define MSBD0_X_SHIFT 28 +#define GB_MSPOS1 0x4014 +#define MS_X3_SHIFT 0 +#define MS_Y3_SHIFT 4 +#define MS_X4_SHIFT 8 +#define MS_Y4_SHIFT 12 +#define MS_X5_SHIFT 16 +#define MS_Y5_SHIFT 20 +#define MSBD1_SHIFT 24 +#define GB_TILE_CONFIG 0x4018 +#define ENABLE_TILING (1 << 0) +#define PIPE_COUNT_MASK 0x0000000E +#define PIPE_COUNT_SHIFT 1 +#define TILE_SIZE_8 (0 << 4) +#define TILE_SIZE_16 (1 << 4) +#define TILE_SIZE_32 (2 << 4) +#define SUBPIXEL_1_12 (0 << 16) +#define SUBPIXEL_1_16 (1 << 16) +#define GB_SELECT 0x401C +#define GB_AA_CONFIG 0x4020 +#define GB_PIPE_SELECT 0x402C +#define GA_ENHANCE 0x4274 +#define GA_DEADLOCK_CNTL (1 << 0) +#define GA_FASTSYNC_CNTL (1 << 1) +#define GA_POLY_MODE 0x4288 +#define FRONT_PTYPE_POINT (0 << 4) +#define FRONT_PTYPE_LINE (1 << 4) +#define FRONT_PTYPE_TRIANGE (2 << 4) +#define BACK_PTYPE_POINT (0 << 7) +#define BACK_PTYPE_LINE (1 << 7) +#define BACK_PTYPE_TRIANGE (2 << 7) +#define GA_ROUND_MODE 0x428C +#define GEOMETRY_ROUND_TRUNC (0 << 0) +#define GEOMETRY_ROUND_NEAREST (1 << 0) +#define COLOR_ROUND_TRUNC (0 << 2) +#define COLOR_ROUND_NEAREST (1 << 2) +#define SU_REG_DEST 0x42C8 +#define RB3D_DSTCACHE_CTLSTAT 0x4E4C +#define RB3D_DC_FLUSH (2 << 0) +#define RB3D_DC_FREE (2 << 2) +#define RB3D_DC_FINISH (1 << 4) +#define ZB_ZCACHE_CTLSTAT 0x4F18 +#define ZC_FLUSH (1 << 0) +#define ZC_FREE (1 << 1) +#define DC_LB_MEMORY_SPLIT 0x6520 +#define DC_LB_MEMORY_SPLIT_MASK 0x00000003 +#define DC_LB_MEMORY_SPLIT_SHIFT 0 +#define DC_LB_MEMORY_SPLIT_D1HALF_D2HALF 0 +#define DC_LB_MEMORY_SPLIT_D1_3Q_D2_1Q 1 +#define DC_LB_MEMORY_SPLIT_D1_ONLY 2 +#define DC_LB_MEMORY_SPLIT_D1_1Q_D2_3Q 3 +#define DC_LB_MEMORY_SPLIT_SHIFT_MODE (1 << 2) +#define DC_LB_DISP1_END_ADR_SHIFT 4 +#define DC_LB_DISP1_END_ADR_MASK 0x00007FF0 +#define D1MODE_PRIORITY_A_CNT 0x6548 +#define MODE_PRIORITY_MARK_MASK 0x00007FFF +#define MODE_PRIORITY_OFF (1 << 16) +#define MODE_PRIORITY_ALWAYS_ON (1 << 20) +#define MODE_PRIORITY_FORCE_MASK (1 << 24) +#define D1MODE_PRIORITY_B_CNT 0x654C +#define LB_MAX_REQ_OUTSTANDING 0x6D58 +#define LB_D1_MAX_REQ_OUTSTANDING_MASK 0x0000000F +#define LB_D1_MAX_REQ_OUTSTANDING_SHIFT 0 +#define LB_D2_MAX_REQ_OUTSTANDING_MASK 0x000F0000 +#define LB_D2_MAX_REQ_OUTSTANDING_SHIFT 16 +#define D2MODE_PRIORITY_A_CNT 0x6D48 +#define D2MODE_PRIORITY_B_CNT 0x6D4C + +/* ix[MC] registers */ +#define MC_FB_LOCATION 0x01 +#define MC_FB_START_MASK 0x0000FFFF +#define MC_FB_START_SHIFT 0 +#define MC_FB_TOP_MASK 0xFFFF0000 +#define MC_FB_TOP_SHIFT 16 +#define MC_AGP_LOCATION 0x02 +#define MC_AGP_START_MASK 0x0000FFFF +#define MC_AGP_START_SHIFT 0 +#define MC_AGP_TOP_MASK 0xFFFF0000 +#define MC_AGP_TOP_SHIFT 16 +#define MC_AGP_BASE 0x03 +#define MC_AGP_BASE_2 0x04 +#define MC_CNTL 0x5 +#define MEM_NUM_CHANNELS_MASK 0x00000003 +#define MC_STATUS 0x08 +#define MC_STATUS_IDLE (1 << 4) +#define MC_MISC_LAT_TIMER 0x09 +#define MC_CPR_INIT_LAT_MASK 0x0000000F +#define MC_VF_INIT_LAT_MASK 0x000000F0 +#define MC_DISP0R_INIT_LAT_MASK 0x00000F00 +#define MC_DISP0R_INIT_LAT_SHIFT 8 +#define MC_DISP1R_INIT_LAT_MASK 0x0000F000 +#define MC_DISP1R_INIT_LAT_SHIFT 12 +#define MC_FIXED_INIT_LAT_MASK 0x000F0000 +#define MC_E2R_INIT_LAT_MASK 0x00F00000 +#define SAME_PAGE_PRIO_MASK 0x0F000000 +#define MC_GLOBW_INIT_LAT_MASK 0xF0000000 + + +#endif + -- GitLab From e46074effd5510e7a8fe34b93828d98a50835da2 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Michel=20D=C3=A4nzer?= Date: Tue, 28 Jul 2009 12:30:55 +0200 Subject: [PATCH 0462/1342] drm/radeon: Don't unreserve twice on failure to validate. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This is done later in radeon_object_list_unvalidate(). Doing it twice triggers a BUG in TTM, rendering X on KMS unusable until reboot. Signed-off-by: Michel Dänzer Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_object.c | 1 - 1 file changed, 1 deletion(-) diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c index d5b1fd562d8..3961a44c5dc 100644 --- a/drivers/gpu/drm/radeon/radeon_object.c +++ b/drivers/gpu/drm/radeon/radeon_object.c @@ -433,7 +433,6 @@ int radeon_object_list_validate(struct list_head *head, void *fence) robj->tobj.proposed_placement, true, false); if (unlikely(r)) { - radeon_object_list_unreserve(head); DRM_ERROR("radeon: failed to validate.\n"); return r; } -- GitLab From 1ab2e1059916b917af19e4137a4222988bd7a169 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Michel=20D=C3=A4nzer?= Date: Tue, 28 Jul 2009 12:30:56 +0200 Subject: [PATCH 0463/1342] drm/radeon: Fall back to evicting BOs with memcpy if necessary. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Otherwise if there's no GTT space we would fail the eviction, leading to cascaded failure. Signed-off-by: Michel Dänzer Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_ttm.c | 15 +++++++++------ 1 file changed, 9 insertions(+), 6 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon_ttm.c b/drivers/gpu/drm/radeon/radeon_ttm.c index 37e1cbcce3a..f3469b96208 100644 --- a/drivers/gpu/drm/radeon/radeon_ttm.c +++ b/drivers/gpu/drm/radeon/radeon_ttm.c @@ -355,23 +355,26 @@ static int radeon_bo_move(struct ttm_buffer_object *bo, if (!rdev->cp.ready) { /* use memcpy */ DRM_ERROR("CP is not ready use memcpy.\n"); - return ttm_bo_move_memcpy(bo, evict, no_wait, new_mem); + goto memcpy; } if (old_mem->mem_type == TTM_PL_VRAM && new_mem->mem_type == TTM_PL_SYSTEM) { - return radeon_move_vram_ram(bo, evict, interruptible, + r = radeon_move_vram_ram(bo, evict, interruptible, no_wait, new_mem); } else if (old_mem->mem_type == TTM_PL_SYSTEM && new_mem->mem_type == TTM_PL_VRAM) { - return radeon_move_ram_vram(bo, evict, interruptible, + r = radeon_move_ram_vram(bo, evict, interruptible, no_wait, new_mem); } else { r = radeon_move_blit(bo, evict, no_wait, new_mem, old_mem); - if (unlikely(r)) { - return r; - } } + + if (r) { +memcpy: + r = ttm_bo_move_memcpy(bo, evict, no_wait, new_mem); + } + return r; } -- GitLab From 664f86590295217b2319edf88830e87b800f6c4a Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Michel=20D=C3=A4nzer?= Date: Tue, 28 Jul 2009 12:30:57 +0200 Subject: [PATCH 0464/1342] drm/radeon: Pay more attention to object placement requested by userspace. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Previously we were basically always setting the GTT and VRAM flags regardless of what userspace requested. Signed-off-by: Michel Dänzer Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_object.c | 25 +++++++++++-------------- 1 file changed, 11 insertions(+), 14 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c index 3961a44c5dc..81573c3a9b4 100644 --- a/drivers/gpu/drm/radeon/radeon_object.c +++ b/drivers/gpu/drm/radeon/radeon_object.c @@ -103,16 +103,16 @@ static inline uint32_t radeon_object_flags_from_domain(uint32_t domain) { uint32_t flags = 0; if (domain & RADEON_GEM_DOMAIN_VRAM) { - flags |= TTM_PL_FLAG_VRAM; + flags |= TTM_PL_FLAG_VRAM | TTM_PL_FLAG_WC | TTM_PL_FLAG_UNCACHED; } if (domain & RADEON_GEM_DOMAIN_GTT) { - flags |= TTM_PL_FLAG_TT; + flags |= TTM_PL_FLAG_TT | TTM_PL_FLAG_WC | TTM_PL_FLAG_UNCACHED; } if (domain & RADEON_GEM_DOMAIN_CPU) { - flags |= TTM_PL_FLAG_SYSTEM; + flags |= TTM_PL_FLAG_SYSTEM | TTM_PL_MASK_CACHING; } if (!flags) { - flags |= TTM_PL_FLAG_SYSTEM; + flags |= TTM_PL_FLAG_SYSTEM | TTM_PL_MASK_CACHING; } return flags; } @@ -408,7 +408,6 @@ int radeon_object_list_validate(struct list_head *head, void *fence) struct radeon_object *robj; struct radeon_fence *old_fence = NULL; struct list_head *i; - uint32_t flags; int r; r = radeon_object_list_reserve(head); @@ -419,16 +418,14 @@ int radeon_object_list_validate(struct list_head *head, void *fence) list_for_each(i, head) { lobj = list_entry(i, struct radeon_object_list, list); robj = lobj->robj; - if (lobj->wdomain) { - flags = radeon_object_flags_from_domain(lobj->wdomain); - flags |= TTM_PL_FLAG_TT; - } else { - flags = radeon_object_flags_from_domain(lobj->rdomain); - flags |= TTM_PL_FLAG_TT; - flags |= TTM_PL_FLAG_VRAM; - } if (!robj->pin_count) { - robj->tobj.proposed_placement = flags | TTM_PL_MASK_CACHING; + if (lobj->wdomain) { + robj->tobj.proposed_placement = + radeon_object_flags_from_domain(lobj->wdomain); + } else { + robj->tobj.proposed_placement = + radeon_object_flags_from_domain(lobj->rdomain); + } r = ttm_buffer_object_validate(&robj->tobj, robj->tobj.proposed_placement, true, false); -- GitLab From 7a50f01a4ab89d5c05eb2cf62e206ac0bfc61d2c Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Tue, 21 Jul 2009 20:39:30 +1000 Subject: [PATCH 0465/1342] drm/radeon/kms: vram sizing on certain r100 chips needs workaround. If an rn50/r100/m6/m7 GPU has < 64MB RAM, i.e. 8/16/32, the aperture used to calculate the MC_FB_LOCATION needs to be worked out from the CONFIG_APER_SIZE register, and not the actual vram size. TTM VRAM size was also being initialised wrong, use actual vram size to initialise it. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 34 +++++++++++++++++--------- drivers/gpu/drm/radeon/r520.c | 4 +-- drivers/gpu/drm/radeon/r600.c | 5 ++-- drivers/gpu/drm/radeon/radeon.h | 5 +++- drivers/gpu/drm/radeon/radeon_device.c | 20 ++++++++------- drivers/gpu/drm/radeon/radeon_gem.c | 4 +-- drivers/gpu/drm/radeon/radeon_ttm.c | 4 +-- drivers/gpu/drm/radeon/rs400.c | 4 +-- drivers/gpu/drm/radeon/rs600.c | 2 +- drivers/gpu/drm/radeon/rs690.c | 7 +++--- drivers/gpu/drm/radeon/rv515.c | 7 ++---- drivers/gpu/drm/radeon/rv770.c | 2 +- 12 files changed, 56 insertions(+), 42 deletions(-) diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index 0e00fef0b84..05a44896dff 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -173,8 +173,12 @@ void r100_mc_setup(struct radeon_device *rdev) DRM_ERROR("Failed to register debugfs file for R100 MC !\n"); } /* Write VRAM size in case we are limiting it */ - WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); - tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1; + WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.real_vram_size); + /* Novell bug 204882 for RN50/M6/M7 with 8/16/32MB VRAM, + * if the aperture is 64MB but we have 32MB VRAM + * we report only 32MB VRAM but we have to set MC_FB_LOCATION + * to 64MB, otherwise the gpu accidentially dies */ + tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1; tmp = REG_SET(RADEON_MC_FB_TOP, tmp >> 16); tmp |= REG_SET(RADEON_MC_FB_START, rdev->mc.vram_location >> 16); WREG32(RADEON_MC_FB_LOCATION, tmp); @@ -1447,25 +1451,28 @@ void r100_vram_init_sizes(struct radeon_device *rdev) uint32_t tom; /* read NB_TOM to get the amount of ram stolen for the GPU */ tom = RREG32(RADEON_NB_TOM); - rdev->mc.vram_size = (((tom >> 16) - (tom & 0xffff) + 1) << 16); + rdev->mc.real_vram_size = (((tom >> 16) - (tom & 0xffff) + 1) << 16); /* for IGPs we need to keep VRAM where it was put by the BIOS */ rdev->mc.vram_location = (tom & 0xffff) << 16; - WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); + WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.real_vram_size); + rdev->mc.mc_vram_size = rdev->mc.real_vram_size; } else { - rdev->mc.vram_size = RREG32(RADEON_CONFIG_MEMSIZE); + rdev->mc.real_vram_size = RREG32(RADEON_CONFIG_MEMSIZE); /* Some production boards of m6 will report 0 * if it's 8 MB */ - if (rdev->mc.vram_size == 0) { - rdev->mc.vram_size = 8192 * 1024; - WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); + if (rdev->mc.real_vram_size == 0) { + rdev->mc.real_vram_size = 8192 * 1024; + WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.real_vram_size); } /* let driver place VRAM */ rdev->mc.vram_location = 0xFFFFFFFFUL; /* Fix for RN50, M6, M7 with 8/16/32(??) MBs of VRAM - * Novell bug 204882 + along with lots of ubuntu ones */ - if (config_aper_size > rdev->mc.vram_size) - rdev->mc.vram_size = config_aper_size; + if (config_aper_size > rdev->mc.real_vram_size) + rdev->mc.mc_vram_size = config_aper_size; + else + rdev->mc.mc_vram_size = rdev->mc.real_vram_size; } /* work out accessible VRAM */ @@ -1477,8 +1484,11 @@ void r100_vram_init_sizes(struct radeon_device *rdev) if (accessible > rdev->mc.aper_size) accessible = rdev->mc.aper_size; - if (rdev->mc.vram_size > rdev->mc.aper_size) - rdev->mc.vram_size = rdev->mc.aper_size; + if (rdev->mc.mc_vram_size > rdev->mc.aper_size) + rdev->mc.mc_vram_size = rdev->mc.aper_size; + + if (rdev->mc.real_vram_size > rdev->mc.aper_size) + rdev->mc.real_vram_size = rdev->mc.aper_size; } void r100_vram_info(struct radeon_device *rdev) diff --git a/drivers/gpu/drm/radeon/r520.c b/drivers/gpu/drm/radeon/r520.c index 0a981e2ee2f..09fb0b6ec7d 100644 --- a/drivers/gpu/drm/radeon/r520.c +++ b/drivers/gpu/drm/radeon/r520.c @@ -95,8 +95,8 @@ int r520_mc_init(struct radeon_device *rdev) "programming pipes. Bad things might happen.\n"); } /* Write VRAM size in case we are limiting it */ - WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); - tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1; + WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.real_vram_size); + tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1; tmp = REG_SET(R520_MC_FB_TOP, tmp >> 16); tmp |= REG_SET(R520_MC_FB_START, rdev->mc.vram_location >> 16); WREG32_MC(R520_MC_FB_LOCATION, tmp); diff --git a/drivers/gpu/drm/radeon/r600.c b/drivers/gpu/drm/radeon/r600.c index c45559fc97f..538cd907df6 100644 --- a/drivers/gpu/drm/radeon/r600.c +++ b/drivers/gpu/drm/radeon/r600.c @@ -67,7 +67,7 @@ int r600_mc_init(struct radeon_device *rdev) "programming pipes. Bad things might happen.\n"); } - tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1; + tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1; tmp = REG_SET(R600_MC_FB_TOP, tmp >> 24); tmp |= REG_SET(R600_MC_FB_BASE, rdev->mc.vram_location >> 24); WREG32(R600_MC_VM_FB_LOCATION, tmp); @@ -140,7 +140,8 @@ void r600_vram_get_type(struct radeon_device *rdev) void r600_vram_info(struct radeon_device *rdev) { r600_vram_get_type(rdev); - rdev->mc.vram_size = RREG32(R600_CONFIG_MEMSIZE); + rdev->mc.real_vram_size = RREG32(R600_CONFIG_MEMSIZE); + rdev->mc.mc_vram_size = rdev->mc.real_vram_size; /* Could aper size report 0 ? */ rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index 63a3fe32e58..045b33b3bf2 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -332,8 +332,11 @@ struct radeon_mc { unsigned gtt_location; unsigned gtt_size; unsigned vram_location; - unsigned vram_size; + /* for some chips with <= 32MB we need to lie + * about vram size near mc fb location */ + unsigned mc_vram_size; unsigned vram_width; + unsigned real_vram_size; int vram_mtrr; bool vram_is_ddr; }; diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c index f78db5c8008..6d1749e4422 100644 --- a/drivers/gpu/drm/radeon/radeon_device.c +++ b/drivers/gpu/drm/radeon/radeon_device.c @@ -121,7 +121,7 @@ int radeon_mc_setup(struct radeon_device *rdev) if (rdev->mc.vram_location != 0xFFFFFFFFUL) { /* vram location was already setup try to put gtt after * if it fits */ - tmp = rdev->mc.vram_location + rdev->mc.vram_size; + tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size; tmp = (tmp + rdev->mc.gtt_size - 1) & ~(rdev->mc.gtt_size - 1); if ((0xFFFFFFFFUL - tmp) >= rdev->mc.gtt_size) { rdev->mc.gtt_location = tmp; @@ -136,13 +136,13 @@ int radeon_mc_setup(struct radeon_device *rdev) } else if (rdev->mc.gtt_location != 0xFFFFFFFFUL) { /* gtt location was already setup try to put vram before * if it fits */ - if (rdev->mc.vram_size < rdev->mc.gtt_location) { + if (rdev->mc.mc_vram_size < rdev->mc.gtt_location) { rdev->mc.vram_location = 0; } else { tmp = rdev->mc.gtt_location + rdev->mc.gtt_size; - tmp += (rdev->mc.vram_size - 1); - tmp &= ~(rdev->mc.vram_size - 1); - if ((0xFFFFFFFFUL - tmp) >= rdev->mc.vram_size) { + tmp += (rdev->mc.mc_vram_size - 1); + tmp &= ~(rdev->mc.mc_vram_size - 1); + if ((0xFFFFFFFFUL - tmp) >= rdev->mc.mc_vram_size) { rdev->mc.vram_location = tmp; } else { printk(KERN_ERR "[drm] vram too big to fit " @@ -152,12 +152,14 @@ int radeon_mc_setup(struct radeon_device *rdev) } } else { rdev->mc.vram_location = 0; - rdev->mc.gtt_location = rdev->mc.vram_size; + rdev->mc.gtt_location = rdev->mc.mc_vram_size; } - DRM_INFO("radeon: VRAM %uM\n", rdev->mc.vram_size >> 20); + DRM_INFO("radeon: VRAM %uM\n", rdev->mc.real_vram_size >> 20); DRM_INFO("radeon: VRAM from 0x%08X to 0x%08X\n", rdev->mc.vram_location, - rdev->mc.vram_location + rdev->mc.vram_size - 1); + rdev->mc.vram_location + rdev->mc.mc_vram_size - 1); + if (rdev->mc.real_vram_size != rdev->mc.mc_vram_size) + DRM_INFO("radeon: VRAM less than aperture workaround enabled\n"); DRM_INFO("radeon: GTT %uM\n", rdev->mc.gtt_size >> 20); DRM_INFO("radeon: GTT from 0x%08X to 0x%08X\n", rdev->mc.gtt_location, @@ -573,7 +575,7 @@ int radeon_device_init(struct radeon_device *rdev, rdev->mc.vram_mtrr = mtrr_add(rdev->mc.aper_base, rdev->mc.aper_size, MTRR_TYPE_WRCOMB, 1); DRM_INFO("Detected VRAM RAM=%uM, BAR=%uM\n", - rdev->mc.vram_size >> 20, + rdev->mc.real_vram_size >> 20, (unsigned)rdev->mc.aper_size >> 20); DRM_INFO("RAM width %dbits %cDR\n", rdev->mc.vram_width, rdev->mc.vram_is_ddr ? 'D' : 'S'); diff --git a/drivers/gpu/drm/radeon/radeon_gem.c b/drivers/gpu/drm/radeon/radeon_gem.c index 12542087b29..cded5180c75 100644 --- a/drivers/gpu/drm/radeon/radeon_gem.c +++ b/drivers/gpu/drm/radeon/radeon_gem.c @@ -157,9 +157,9 @@ int radeon_gem_info_ioctl(struct drm_device *dev, void *data, struct radeon_device *rdev = dev->dev_private; struct drm_radeon_gem_info *args = data; - args->vram_size = rdev->mc.vram_size; + args->vram_size = rdev->mc.real_vram_size; /* FIXME: report somethings that makes sense */ - args->vram_visible = rdev->mc.vram_size - (4 * 1024 * 1024); + args->vram_visible = rdev->mc.real_vram_size - (4 * 1024 * 1024); args->gart_size = rdev->mc.gtt_size; return 0; } diff --git a/drivers/gpu/drm/radeon/radeon_ttm.c b/drivers/gpu/drm/radeon/radeon_ttm.c index f3469b96208..15c3531377e 100644 --- a/drivers/gpu/drm/radeon/radeon_ttm.c +++ b/drivers/gpu/drm/radeon/radeon_ttm.c @@ -454,7 +454,7 @@ int radeon_ttm_init(struct radeon_device *rdev) return r; } r = ttm_bo_init_mm(&rdev->mman.bdev, TTM_PL_VRAM, 0, - ((rdev->mc.aper_size) >> PAGE_SHIFT)); + ((rdev->mc.real_vram_size) >> PAGE_SHIFT)); if (r) { DRM_ERROR("Failed initializing VRAM heap.\n"); return r; @@ -471,7 +471,7 @@ int radeon_ttm_init(struct radeon_device *rdev) return r; } DRM_INFO("radeon: %uM of VRAM memory ready\n", - rdev->mc.vram_size / (1024 * 1024)); + rdev->mc.real_vram_size / (1024 * 1024)); r = ttm_bo_init_mm(&rdev->mman.bdev, TTM_PL_TT, 0, ((rdev->mc.gtt_size) >> PAGE_SHIFT)); if (r) { diff --git a/drivers/gpu/drm/radeon/rs400.c b/drivers/gpu/drm/radeon/rs400.c index 96a3c8486d2..b29affd9c5d 100644 --- a/drivers/gpu/drm/radeon/rs400.c +++ b/drivers/gpu/drm/radeon/rs400.c @@ -233,7 +233,7 @@ int rs400_mc_init(struct radeon_device *rdev) rs400_gpu_init(rdev); rs400_gart_disable(rdev); - rdev->mc.gtt_location = rdev->mc.vram_size; + rdev->mc.gtt_location = rdev->mc.mc_vram_size; rdev->mc.gtt_location += (rdev->mc.gtt_size - 1); rdev->mc.gtt_location &= ~(rdev->mc.gtt_size - 1); r = radeon_mc_setup(rdev); @@ -247,7 +247,7 @@ int rs400_mc_init(struct radeon_device *rdev) "programming pipes. Bad things might happen.\n"); } - tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1; + tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1; tmp = REG_SET(RADEON_MC_FB_TOP, tmp >> 16); tmp |= REG_SET(RADEON_MC_FB_START, rdev->mc.vram_location >> 16); WREG32(RADEON_MC_FB_LOCATION, tmp); diff --git a/drivers/gpu/drm/radeon/rs600.c b/drivers/gpu/drm/radeon/rs600.c index bccdce7fd37..bbea6dee4a9 100644 --- a/drivers/gpu/drm/radeon/rs600.c +++ b/drivers/gpu/drm/radeon/rs600.c @@ -223,7 +223,7 @@ int rs600_mc_init(struct radeon_device *rdev) printk(KERN_WARNING "Failed to wait MC idle while " "programming pipes. Bad things might happen.\n"); } - tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1; + tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1; tmp = REG_SET(RS600_MC_FB_TOP, tmp >> 16); tmp |= REG_SET(RS600_MC_FB_START, rdev->mc.vram_location >> 16); WREG32_MC(RS600_MC_FB_LOCATION, tmp); diff --git a/drivers/gpu/drm/radeon/rs690.c b/drivers/gpu/drm/radeon/rs690.c index 97eaee3d28b..839595b0072 100644 --- a/drivers/gpu/drm/radeon/rs690.c +++ b/drivers/gpu/drm/radeon/rs690.c @@ -67,7 +67,7 @@ int rs690_mc_init(struct radeon_device *rdev) rs400_gart_disable(rdev); /* Setup GPU memory space */ - rdev->mc.gtt_location = rdev->mc.vram_size; + rdev->mc.gtt_location = rdev->mc.mc_vram_size; rdev->mc.gtt_location += (rdev->mc.gtt_size - 1); rdev->mc.gtt_location &= ~(rdev->mc.gtt_size - 1); rdev->mc.vram_location = 0xFFFFFFFFUL; @@ -82,7 +82,7 @@ int rs690_mc_init(struct radeon_device *rdev) printk(KERN_WARNING "Failed to wait MC idle while " "programming pipes. Bad things might happen.\n"); } - tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1; + tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1; tmp = REG_SET(RS690_MC_FB_TOP, tmp >> 16); tmp |= REG_SET(RS690_MC_FB_START, rdev->mc.vram_location >> 16); WREG32_MC(RS690_MCCFG_FB_LOCATION, tmp); @@ -228,7 +228,8 @@ void rs690_vram_info(struct radeon_device *rdev) } else { rdev->mc.vram_width = 64; } - rdev->mc.vram_size = RREG32(RADEON_CONFIG_MEMSIZE); + rdev->mc.real_vram_size = RREG32(RADEON_CONFIG_MEMSIZE); + rdev->mc.mc_vram_size = rdev->mc.real_vram_size; rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); diff --git a/drivers/gpu/drm/radeon/rv515.c b/drivers/gpu/drm/radeon/rv515.c index 4fd411893b9..551e608702e 100644 --- a/drivers/gpu/drm/radeon/rv515.c +++ b/drivers/gpu/drm/radeon/rv515.c @@ -100,10 +100,10 @@ int rv515_mc_init(struct radeon_device *rdev) "programming pipes. Bad things might happen.\n"); } /* Write VRAM size in case we are limiting it */ - WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); + WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.real_vram_size); tmp = REG_SET(MC_FB_START, rdev->mc.vram_location >> 16); WREG32(0x134, tmp); - tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1; + tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1; tmp = REG_SET(MC_FB_TOP, tmp >> 16); tmp |= REG_SET(MC_FB_START, rdev->mc.vram_location >> 16); WREG32_MC(MC_FB_LOCATION, tmp); @@ -369,10 +369,7 @@ void rv515_vram_info(struct radeon_device *rdev) fixed20_12 a; rv515_vram_get_type(rdev); - rdev->mc.vram_size = RREG32(CONFIG_MEMSIZE); - rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); - rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); /* FIXME: we should enforce default clock in case GPU is not in * default setup */ diff --git a/drivers/gpu/drm/radeon/rv770.c b/drivers/gpu/drm/radeon/rv770.c index da50cc51ede..21d8ffd5730 100644 --- a/drivers/gpu/drm/radeon/rv770.c +++ b/drivers/gpu/drm/radeon/rv770.c @@ -67,7 +67,7 @@ int rv770_mc_init(struct radeon_device *rdev) "programming pipes. Bad things might happen.\n"); } - tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1; + tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1; tmp = REG_SET(R700_MC_FB_TOP, tmp >> 24); tmp |= REG_SET(R700_MC_FB_BASE, rdev->mc.vram_location >> 24); WREG32(R700_MC_VM_FB_LOCATION, tmp); -- GitLab From 4677f15c60421d48566c48c3149474e64977f071 Mon Sep 17 00:00:00 2001 From: Thomas Hellstrom Date: Tue, 21 Jul 2009 17:45:13 +0200 Subject: [PATCH 0466/1342] drm/ttm: Fix an oops and sync object leak. The code was potentially dereferencig a NULL sync object pointer. At the same time a sync object reference was potentially leaked. Signed-off-by: Thomas Hellstrom Signed-off-by: Dave Airlie --- drivers/gpu/drm/ttm/ttm_bo_util.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/gpu/drm/ttm/ttm_bo_util.c b/drivers/gpu/drm/ttm/ttm_bo_util.c index bdec583901e..3e5d0c4ad85 100644 --- a/drivers/gpu/drm/ttm/ttm_bo_util.c +++ b/drivers/gpu/drm/ttm/ttm_bo_util.c @@ -509,8 +509,8 @@ int ttm_bo_move_accel_cleanup(struct ttm_buffer_object *bo, if (evict) { ret = ttm_bo_wait(bo, false, false, false); spin_unlock(&bo->lock); - driver->sync_obj_unref(&bo->sync_obj); - + if (tmp_obj) + driver->sync_obj_unref(&tmp_obj); if (ret) return ret; @@ -532,6 +532,8 @@ int ttm_bo_move_accel_cleanup(struct ttm_buffer_object *bo, set_bit(TTM_BO_PRIV_FLAG_MOVING, &bo->priv_flags); spin_unlock(&bo->lock); + if (tmp_obj) + driver->sync_obj_unref(&tmp_obj); ret = ttm_buffer_object_transfer(bo, &ghost_obj); if (ret) -- GitLab From 542c6f6df51327dbb180cf4d9b34827e147efe17 Mon Sep 17 00:00:00 2001 From: Thomas Hellstrom Date: Fri, 24 Jul 2009 09:57:34 +0200 Subject: [PATCH 0467/1342] drm/ttm: Fix ttm in-kernel copying of pages with non-standard caching attributes. For x86 this affected highmem pages only, since they were always kmapped cache-coherent, and this is fixed using kmap_atomic_prot(). For other architectures that may not modify the linear kernel map we resort to vmap() for now, since kmap_atomic_prot() generally uses the linear kernel map for lowmem pages. This of course comes with a performance impact and should be optimized when possible. Signed-off-by: Thomas Hellstrom Signed-off-by: Dave Airlie --- drivers/gpu/drm/ttm/ttm_bo_util.c | 63 +++++++++++++++++++++++++------ 1 file changed, 52 insertions(+), 11 deletions(-) diff --git a/drivers/gpu/drm/ttm/ttm_bo_util.c b/drivers/gpu/drm/ttm/ttm_bo_util.c index 3e5d0c4ad85..ce2e6f38ea0 100644 --- a/drivers/gpu/drm/ttm/ttm_bo_util.c +++ b/drivers/gpu/drm/ttm/ttm_bo_util.c @@ -136,7 +136,8 @@ static int ttm_copy_io_page(void *dst, void *src, unsigned long page) } static int ttm_copy_io_ttm_page(struct ttm_tt *ttm, void *src, - unsigned long page) + unsigned long page, + pgprot_t prot) { struct page *d = ttm_tt_get_page(ttm, page); void *dst; @@ -145,17 +146,35 @@ static int ttm_copy_io_ttm_page(struct ttm_tt *ttm, void *src, return -ENOMEM; src = (void *)((unsigned long)src + (page << PAGE_SHIFT)); - dst = kmap(d); + +#ifdef CONFIG_X86 + dst = kmap_atomic_prot(d, KM_USER0, prot); +#else + if (prot != PAGE_KERNEL) + dst = vmap(&d, 1, 0, prot); + else + dst = kmap(d); +#endif if (!dst) return -ENOMEM; memcpy_fromio(dst, src, PAGE_SIZE); - kunmap(d); + +#ifdef CONFIG_X86 + kunmap_atomic(dst, KM_USER0); +#else + if (prot != PAGE_KERNEL) + vunmap(dst); + else + kunmap(d); +#endif + return 0; } static int ttm_copy_ttm_io_page(struct ttm_tt *ttm, void *dst, - unsigned long page) + unsigned long page, + pgprot_t prot) { struct page *s = ttm_tt_get_page(ttm, page); void *src; @@ -164,12 +183,28 @@ static int ttm_copy_ttm_io_page(struct ttm_tt *ttm, void *dst, return -ENOMEM; dst = (void *)((unsigned long)dst + (page << PAGE_SHIFT)); - src = kmap(s); +#ifdef CONFIG_X86 + src = kmap_atomic_prot(s, KM_USER0, prot); +#else + if (prot != PAGE_KERNEL) + src = vmap(&s, 1, 0, prot); + else + src = kmap(s); +#endif if (!src) return -ENOMEM; memcpy_toio(dst, src, PAGE_SIZE); - kunmap(s); + +#ifdef CONFIG_X86 + kunmap_atomic(src, KM_USER0); +#else + if (prot != PAGE_KERNEL) + vunmap(src); + else + kunmap(s); +#endif + return 0; } @@ -214,11 +249,17 @@ int ttm_bo_move_memcpy(struct ttm_buffer_object *bo, for (i = 0; i < new_mem->num_pages; ++i) { page = i * dir + add; - if (old_iomap == NULL) - ret = ttm_copy_ttm_io_page(ttm, new_iomap, page); - else if (new_iomap == NULL) - ret = ttm_copy_io_ttm_page(ttm, old_iomap, page); - else + if (old_iomap == NULL) { + pgprot_t prot = ttm_io_prot(old_mem->placement, + PAGE_KERNEL); + ret = ttm_copy_ttm_io_page(ttm, new_iomap, page, + prot); + } else if (new_iomap == NULL) { + pgprot_t prot = ttm_io_prot(new_mem->placement, + PAGE_KERNEL); + ret = ttm_copy_io_ttm_page(ttm, old_iomap, page, + prot); + } else ret = ttm_copy_io_page(new_iomap, old_iomap, page); if (ret) goto out1; -- GitLab From 73ba651fc246fcc3e446da4155e0425b4219d2c4 Mon Sep 17 00:00:00 2001 From: Thomas Hellstrom Date: Fri, 24 Jul 2009 09:57:33 +0200 Subject: [PATCH 0468/1342] x86: Export kmap_atomic_prot() needed for TTM. This functionality is needed to kmap_atomic() highmem pages that may potentially have or are about to set up other mappings with non-standard caching attributes. Signed-off-by: Thomas Hellstrom Signed-off-by: Dave Airlie --- arch/x86/mm/highmem_32.c | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/x86/mm/highmem_32.c b/arch/x86/mm/highmem_32.c index 58f621e8191..2112ed55e7e 100644 --- a/arch/x86/mm/highmem_32.c +++ b/arch/x86/mm/highmem_32.c @@ -103,6 +103,7 @@ EXPORT_SYMBOL(kmap); EXPORT_SYMBOL(kunmap); EXPORT_SYMBOL(kmap_atomic); EXPORT_SYMBOL(kunmap_atomic); +EXPORT_SYMBOL(kmap_atomic_prot); void __init set_highmem_pages_init(void) { -- GitLab From f121ecfebbea1452a17d57c656def7d1537440f7 Mon Sep 17 00:00:00 2001 From: Thomas Hellstrom Date: Fri, 24 Jul 2009 10:22:36 +0200 Subject: [PATCH 0469/1342] drm/ttm: powerpc: Fix Highmem cache flushing. Temporarily maps highmem pages while flushing to get a valid virtual address to flush. Signed-off-by: Thomas Hellstrom Signed-off-by: Dave Airlie --- drivers/gpu/drm/ttm/ttm_tt.c | 14 ++++++++++---- 1 file changed, 10 insertions(+), 4 deletions(-) diff --git a/drivers/gpu/drm/ttm/ttm_tt.c b/drivers/gpu/drm/ttm/ttm_tt.c index 81ab81f030a..9b2248a80cf 100644 --- a/drivers/gpu/drm/ttm/ttm_tt.c +++ b/drivers/gpu/drm/ttm/ttm_tt.c @@ -86,10 +86,16 @@ void ttm_tt_cache_flush(struct page *pages[], unsigned long num_pages) unsigned long i; for (i = 0; i < num_pages; ++i) { - if (pages[i]) { - unsigned long start = (unsigned long)page_address(pages[i]); - flush_dcache_range(start, start + PAGE_SIZE); - } + struct page *page = pages[i]; + void *page_virtual; + + if (unlikely(page == NULL)) + continue; + + page_virtual = kmap_atomic(page, KM_USER0); + flush_dcache_range((unsigned long) page_virtual, + (unsigned long) page_virtual + PAGE_SIZE); + kunmap_atomic(page_virtual, KM_USER0); } #else if (on_each_cpu(ttm_tt_ipi_handler, NULL, 1) != 0) -- GitLab From 3b170c3b2e688665fbc2845ba5bb4304bf38a119 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Fri, 24 Jul 2009 13:47:45 +1000 Subject: [PATCH 0470/1342] drm/radeon/kms: allow interruptible waits for objects. Blocking here isn't something the X server mouse appreciates, avoid the block and let userspace retry the waits. libdrm_radeon userspace library is also expecting EBUSY not ERESTART Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_fence.c | 2 +- drivers/gpu/drm/radeon/radeon_object.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon_fence.c b/drivers/gpu/drm/radeon/radeon_fence.c index 96afbf5ae2a..b4e48dd2e85 100644 --- a/drivers/gpu/drm/radeon/radeon_fence.c +++ b/drivers/gpu/drm/radeon/radeon_fence.c @@ -195,7 +195,7 @@ retry: r = wait_event_interruptible_timeout(rdev->fence_drv.queue, radeon_fence_signaled(fence), timeout); if (unlikely(r == -ERESTARTSYS)) { - return -ERESTART; + return -EBUSY; } } else { r = wait_event_timeout(rdev->fence_drv.queue, diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c index 81573c3a9b4..dd9ac2fed6d 100644 --- a/drivers/gpu/drm/radeon/radeon_object.c +++ b/drivers/gpu/drm/radeon/radeon_object.c @@ -309,7 +309,7 @@ int radeon_object_wait(struct radeon_object *robj) } spin_lock(&robj->tobj.lock); if (robj->tobj.sync_obj) { - r = ttm_bo_wait(&robj->tobj, true, false, false); + r = ttm_bo_wait(&robj->tobj, true, true, false); } spin_unlock(&robj->tobj.lock); radeon_object_unreserve(robj); -- GitLab From ecc0b32645bf19a3a240e72be3022ab3b46ad3d0 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Michel=20D=C3=A4nzer?= Date: Tue, 21 Jul 2009 11:23:57 +0200 Subject: [PATCH 0471/1342] drm/radeon: Add radeon.test parameter for running BO GPU copy tests. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit If enabled, during initialization BO GTT->VRAM and VRAM->GTT GPU copies are tested across the whole GTT aperture. This has helped uncover the benchmark copy size bug and verify the maximum aperture size supported by the AGP bridge in my PowerBook. Signed-off-by: Michel Dänzer Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/Makefile | 3 +- drivers/gpu/drm/radeon/radeon.h | 7 + drivers/gpu/drm/radeon/radeon_device.c | 3 + drivers/gpu/drm/radeon/radeon_drv.c | 4 + drivers/gpu/drm/radeon/radeon_test.c | 209 +++++++++++++++++++++++++ 5 files changed, 225 insertions(+), 1 deletion(-) create mode 100644 drivers/gpu/drm/radeon/radeon_test.c diff --git a/drivers/gpu/drm/radeon/Makefile b/drivers/gpu/drm/radeon/Makefile index 5fae1e074b4..013d3805994 100644 --- a/drivers/gpu/drm/radeon/Makefile +++ b/drivers/gpu/drm/radeon/Makefile @@ -13,7 +13,8 @@ radeon-$(CONFIG_DRM_RADEON_KMS) += radeon_device.o radeon_kms.o \ radeon_encoders.o radeon_display.o radeon_cursor.o radeon_i2c.o \ radeon_clocks.o radeon_fb.o radeon_gem.o radeon_ring.o radeon_irq_kms.o \ radeon_cs.o radeon_bios.o radeon_benchmark.o r100.o r300.o r420.o \ - rs400.o rs600.o rs690.o rv515.o r520.o r600.o rs780.o rv770.o + rs400.o rs600.o rs690.o rv515.o r520.o r600.o rs780.o rv770.o \ + radeon_test.o radeon-$(CONFIG_COMPAT) += radeon_ioc32.o diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index 045b33b3bf2..b1d945b8ed6 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -64,6 +64,7 @@ extern int radeon_agpmode; extern int radeon_vram_limit; extern int radeon_gart_size; extern int radeon_benchmarking; +extern int radeon_testing; extern int radeon_connector_table; /* @@ -534,6 +535,12 @@ struct radeon_pm { void radeon_benchmark(struct radeon_device *rdev); +/* + * Testing + */ +void radeon_test_moves(struct radeon_device *rdev); + + /* * Debugfs */ diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c index 6d1749e4422..a162ade74b7 100644 --- a/drivers/gpu/drm/radeon/radeon_device.c +++ b/drivers/gpu/drm/radeon/radeon_device.c @@ -638,6 +638,9 @@ int radeon_device_init(struct radeon_device *rdev, if (!ret) { DRM_INFO("radeon: kernel modesetting successfully initialized.\n"); } + if (radeon_testing) { + radeon_test_moves(rdev); + } if (radeon_benchmarking) { radeon_benchmark(rdev); } diff --git a/drivers/gpu/drm/radeon/radeon_drv.c b/drivers/gpu/drm/radeon/radeon_drv.c index 84ba69f4878..3cfcee17dc5 100644 --- a/drivers/gpu/drm/radeon/radeon_drv.c +++ b/drivers/gpu/drm/radeon/radeon_drv.c @@ -89,6 +89,7 @@ int radeon_agpmode = 0; int radeon_vram_limit = 0; int radeon_gart_size = 512; /* default gart size */ int radeon_benchmarking = 0; +int radeon_testing = 0; int radeon_connector_table = 0; #endif @@ -117,6 +118,9 @@ module_param_named(gartsize, radeon_gart_size, int, 0600); MODULE_PARM_DESC(benchmark, "Run benchmark"); module_param_named(benchmark, radeon_benchmarking, int, 0444); +MODULE_PARM_DESC(test, "Run tests"); +module_param_named(test, radeon_testing, int, 0444); + MODULE_PARM_DESC(connector_table, "Force connector table"); module_param_named(connector_table, radeon_connector_table, int, 0444); #endif diff --git a/drivers/gpu/drm/radeon/radeon_test.c b/drivers/gpu/drm/radeon/radeon_test.c new file mode 100644 index 00000000000..03c33cf4e14 --- /dev/null +++ b/drivers/gpu/drm/radeon/radeon_test.c @@ -0,0 +1,209 @@ +/* + * Copyright 2009 VMware, Inc. + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the "Software"), + * to deal in the Software without restriction, including without limitation + * the rights to use, copy, modify, merge, publish, distribute, sublicense, + * and/or sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR + * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, + * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + * + * Authors: Michel Dänzer + */ +#include +#include +#include "radeon_reg.h" +#include "radeon.h" + + +/* Test BO GTT->VRAM and VRAM->GTT GPU copies across the whole GTT aperture */ +void radeon_test_moves(struct radeon_device *rdev) +{ + struct radeon_object *vram_obj = NULL; + struct radeon_object **gtt_obj = NULL; + struct radeon_fence *fence = NULL; + uint64_t gtt_addr, vram_addr; + unsigned i, n, size; + int r; + + size = 1024 * 1024; + + /* Number of tests = + * (Total GTT - IB pool - writeback page - ring buffer) / test size + */ + n = (rdev->mc.gtt_size - RADEON_IB_POOL_SIZE*64*1024 - 4096 - + rdev->cp.ring_size) / size; + + gtt_obj = kzalloc(n * sizeof(*gtt_obj), GFP_KERNEL); + if (!gtt_obj) { + DRM_ERROR("Failed to allocate %d pointers\n", n); + r = 1; + goto out_cleanup; + } + + r = radeon_object_create(rdev, NULL, size, true, RADEON_GEM_DOMAIN_VRAM, + false, &vram_obj); + if (r) { + DRM_ERROR("Failed to create VRAM object\n"); + goto out_cleanup; + } + + r = radeon_object_pin(vram_obj, RADEON_GEM_DOMAIN_VRAM, &vram_addr); + if (r) { + DRM_ERROR("Failed to pin VRAM object\n"); + goto out_cleanup; + } + + for (i = 0; i < n; i++) { + void *gtt_map, *vram_map; + void **gtt_start, **gtt_end; + void **vram_start, **vram_end; + + r = radeon_object_create(rdev, NULL, size, true, + RADEON_GEM_DOMAIN_GTT, false, gtt_obj + i); + if (r) { + DRM_ERROR("Failed to create GTT object %d\n", i); + goto out_cleanup; + } + + r = radeon_object_pin(gtt_obj[i], RADEON_GEM_DOMAIN_GTT, >t_addr); + if (r) { + DRM_ERROR("Failed to pin GTT object %d\n", i); + goto out_cleanup; + } + + r = radeon_object_kmap(gtt_obj[i], >t_map); + if (r) { + DRM_ERROR("Failed to map GTT object %d\n", i); + goto out_cleanup; + } + + for (gtt_start = gtt_map, gtt_end = gtt_map + size; + gtt_start < gtt_end; + gtt_start++) + *gtt_start = gtt_start; + + radeon_object_kunmap(gtt_obj[i]); + + r = radeon_fence_create(rdev, &fence); + if (r) { + DRM_ERROR("Failed to create GTT->VRAM fence %d\n", i); + goto out_cleanup; + } + + r = radeon_copy(rdev, gtt_addr, vram_addr, size / 4096, fence); + if (r) { + DRM_ERROR("Failed GTT->VRAM copy %d\n", i); + goto out_cleanup; + } + + r = radeon_fence_wait(fence, false); + if (r) { + DRM_ERROR("Failed to wait for GTT->VRAM fence %d\n", i); + goto out_cleanup; + } + + radeon_fence_unref(&fence); + + r = radeon_object_kmap(vram_obj, &vram_map); + if (r) { + DRM_ERROR("Failed to map VRAM object after copy %d\n", i); + goto out_cleanup; + } + + for (gtt_start = gtt_map, gtt_end = gtt_map + size, + vram_start = vram_map, vram_end = vram_map + size; + vram_start < vram_end; + gtt_start++, vram_start++) { + if (*vram_start != gtt_start) { + DRM_ERROR("Incorrect GTT->VRAM copy %d: Got 0x%p, " + "expected 0x%p (GTT map 0x%p-0x%p)\n", + i, *vram_start, gtt_start, gtt_map, + gtt_end); + radeon_object_kunmap(vram_obj); + goto out_cleanup; + } + *vram_start = vram_start; + } + + radeon_object_kunmap(vram_obj); + + r = radeon_fence_create(rdev, &fence); + if (r) { + DRM_ERROR("Failed to create VRAM->GTT fence %d\n", i); + goto out_cleanup; + } + + r = radeon_copy(rdev, vram_addr, gtt_addr, size / 4096, fence); + if (r) { + DRM_ERROR("Failed VRAM->GTT copy %d\n", i); + goto out_cleanup; + } + + r = radeon_fence_wait(fence, false); + if (r) { + DRM_ERROR("Failed to wait for VRAM->GTT fence %d\n", i); + goto out_cleanup; + } + + radeon_fence_unref(&fence); + + r = radeon_object_kmap(gtt_obj[i], >t_map); + if (r) { + DRM_ERROR("Failed to map GTT object after copy %d\n", i); + goto out_cleanup; + } + + for (gtt_start = gtt_map, gtt_end = gtt_map + size, + vram_start = vram_map, vram_end = vram_map + size; + gtt_start < gtt_end; + gtt_start++, vram_start++) { + if (*gtt_start != vram_start) { + DRM_ERROR("Incorrect VRAM->GTT copy %d: Got 0x%p, " + "expected 0x%p (VRAM map 0x%p-0x%p)\n", + i, *gtt_start, vram_start, vram_map, + vram_end); + radeon_object_kunmap(gtt_obj[i]); + goto out_cleanup; + } + } + + radeon_object_kunmap(gtt_obj[i]); + + DRM_INFO("Tested GTT->VRAM and VRAM->GTT copy for GTT offset 0x%llx\n", + gtt_addr - rdev->mc.gtt_location); + } + +out_cleanup: + if (vram_obj) { + radeon_object_unpin(vram_obj); + radeon_object_unref(&vram_obj); + } + if (gtt_obj) { + for (i = 0; i < n; i++) { + if (gtt_obj[i]) { + radeon_object_unpin(gtt_obj[i]); + radeon_object_unref(>t_obj[i]); + } + } + kfree(gtt_obj); + } + if (fence) { + radeon_fence_unref(&fence); + } + if (r) { + printk(KERN_WARNING "Error while testing BO move.\n"); + } +} + -- GitLab From ea3c13bd8c2ed1d3670bd72e60f562a427355fdf Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Michel=20D=C3=A4nzer?= Date: Mon, 20 Jul 2009 01:44:03 +0200 Subject: [PATCH 0472/1342] drm/radeon: Fix size used for benchmarking BO copies. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The incorrect size caused benchmark results to be inflated by a factor of 4. Signed-off-by: Michel Dänzer Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_benchmark.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon_benchmark.c b/drivers/gpu/drm/radeon/radeon_benchmark.c index c44403a2ca7..2e938f7496f 100644 --- a/drivers/gpu/drm/radeon/radeon_benchmark.c +++ b/drivers/gpu/drm/radeon/radeon_benchmark.c @@ -63,7 +63,7 @@ void radeon_benchmark_move(struct radeon_device *rdev, unsigned bsize, if (r) { goto out_cleanup; } - r = radeon_copy_dma(rdev, saddr, daddr, size >> 14, fence); + r = radeon_copy_dma(rdev, saddr, daddr, size / 4096, fence); if (r) { goto out_cleanup; } @@ -88,7 +88,7 @@ void radeon_benchmark_move(struct radeon_device *rdev, unsigned bsize, if (r) { goto out_cleanup; } - r = radeon_copy_blit(rdev, saddr, daddr, size >> 14, fence); + r = radeon_copy_blit(rdev, saddr, daddr, size / 4096, fence); if (r) { goto out_cleanup; } -- GitLab From b42db2b12df7b4f7b2ace581a7726cb5bcb2d658 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Wed, 29 Jul 2009 16:56:52 +1000 Subject: [PATCH 0473/1342] drm/ttm: fix highuser vs dma32 confusion. DMA32 and highmem are sort of exclusive. Noticed by AndrewR on #radeon. Signed-off-by: Dave Airlie --- drivers/gpu/drm/ttm/ttm_tt.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/ttm/ttm_tt.c b/drivers/gpu/drm/ttm/ttm_tt.c index 9b2248a80cf..b8b6c4a5f98 100644 --- a/drivers/gpu/drm/ttm/ttm_tt.c +++ b/drivers/gpu/drm/ttm/ttm_tt.c @@ -137,13 +137,15 @@ static void ttm_tt_free_page_directory(struct ttm_tt *ttm) static struct page *ttm_tt_alloc_page(unsigned page_flags) { - gfp_t gfp_flags = GFP_HIGHUSER; + gfp_t gfp_flags = GFP_USER; if (page_flags & TTM_PAGE_FLAG_ZERO_ALLOC) gfp_flags |= __GFP_ZERO; if (page_flags & TTM_PAGE_FLAG_DMA32) gfp_flags |= __GFP_DMA32; + else + gfp_flags |= __GFP_HIGHMEM; return alloc_page(gfp_flags); } -- GitLab From ed8f0d9e708a1a7c9222e7d0a35d97521e904223 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Wed, 29 Jul 2009 17:07:38 +1000 Subject: [PATCH 0474/1342] drm/radeon: set fb aperture sizes for framebuffer handoff. This will allow efi/vesa to handoff to radeon. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_fb.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/gpu/drm/radeon/radeon_fb.c b/drivers/gpu/drm/radeon/radeon_fb.c index 36d2f5588f2..3206c0ad7b6 100644 --- a/drivers/gpu/drm/radeon/radeon_fb.c +++ b/drivers/gpu/drm/radeon/radeon_fb.c @@ -602,6 +602,11 @@ int radeonfb_create(struct radeon_device *rdev, info->var.width = -1; info->var.xres = fb_width; info->var.yres = fb_height; + + /* setup aperture base/size for vesafb takeover */ + info->aperture_base = rdev->ddev->mode_config.fb_base; + info->aperture_size = rdev->mc.real_vram_size; + info->fix.mmio_start = 0; info->fix.mmio_len = 0; info->pixmap.size = 64*1024; -- GitLab From 78735cffc2d9ab0dec32f1ba7cbc1d84b45bbf29 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Wed, 29 Jul 2009 14:35:20 +0200 Subject: [PATCH 0475/1342] ALSA: hda: fix out-of-bound hdmi_eld.sad[] write e->sad[] is declared with size ELD_MAX_SAD=16, but the guard allows range 0-31. Signed-off-by: Roel Kluin Signed-off-by: Wu Fengguang Signed-off-by: Takashi Iwai --- sound/pci/hda/hda_eld.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/sound/pci/hda/hda_eld.c b/sound/pci/hda/hda_eld.c index fcad5ec3177..9446a5abea1 100644 --- a/sound/pci/hda/hda_eld.c +++ b/sound/pci/hda/hda_eld.c @@ -508,7 +508,7 @@ static void hdmi_write_eld_info(struct snd_info_entry *entry, char name[64]; char *sname; long long val; - int n; + unsigned int n; while (!snd_info_get_line(buffer, line, sizeof(line))) { if (sscanf(line, "%s %llx", name, &val) != 2) @@ -539,7 +539,7 @@ static void hdmi_write_eld_info(struct snd_info_entry *entry, sname++; n = 10 * n + name[4] - '0'; } - if (n < 0 || n > 31) /* double the CEA limit */ + if (n >= ELD_MAX_SAD) continue; if (!strcmp(sname, "_coding_type")) e->sad[n].format = val; -- GitLab From c45ec06c74512265969aef40b00f320c6afb7a90 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Wed, 29 Jul 2009 11:46:59 +0200 Subject: [PATCH 0476/1342] sound: aedsp16: Buffer overflow DSPVersion is declared as char[3], but the sprintf writes at least 4 bytes including terminating null. Signed-off-by: Roel Kluin Signed-off-by: Takashi Iwai --- sound/oss/aedsp16.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) diff --git a/sound/oss/aedsp16.c b/sound/oss/aedsp16.c index 3ee9900ffd7..35b5912cf3f 100644 --- a/sound/oss/aedsp16.c +++ b/sound/oss/aedsp16.c @@ -325,8 +325,9 @@ /* * Size of character arrays that store name and version of sound card */ -#define CARDNAMELEN 15 /* Size of the card's name in chars */ -#define CARDVERLEN 2 /* Size of the card's version in chars */ +#define CARDNAMELEN 15 /* Size of the card's name in chars */ +#define CARDVERLEN 10 /* Size of the card's version in chars */ +#define CARDVERDIGITS 2 /* Number of digits in the version */ #if defined(CONFIG_SC6600) /* @@ -410,7 +411,7 @@ static int soft_cfg __initdata = 0; /* bitmapped config */ static int soft_cfg_mss __initdata = 0; /* bitmapped mss config */ -static int ver[CARDVERLEN] __initdata = {0, 0}; /* DSP Ver: +static int ver[CARDVERDIGITS] __initdata = {0, 0}; /* DSP Ver: hi->ver[0] lo->ver[1] */ #if defined(CONFIG_SC6600) @@ -957,7 +958,7 @@ static int __init aedsp16_dsp_version(int port) * string is finished. */ ver[len++] = ret; - } while (len < CARDVERLEN); + } while (len < CARDVERDIGITS); sprintf(DSPVersion, "%d.%d", ver[0], ver[1]); DBG(("success.\n")); -- GitLab From a987004fbcf163b100d227284999602f83044d7e Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Wed, 29 Jul 2009 12:12:09 +0200 Subject: [PATCH 0477/1342] sound: mpu401.c: Buffer overflow mpu_synth_info[m].name is a char[30], and the minimum length of the data written by sprintf is 31 bytes including terminating null. Signed-off-by: Roel Kluin Signed-off-by: Takashi Iwai --- sound/oss/mpu401.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/oss/mpu401.c b/sound/oss/mpu401.c index 1b2316f35b1..734b8f9e2f7 100644 --- a/sound/oss/mpu401.c +++ b/sound/oss/mpu401.c @@ -1074,7 +1074,7 @@ int attach_mpu401(struct address_info *hw_config, struct module *owner) sprintf(mpu_synth_info[m].name, "%s (MPU401)", hw_config->name); else sprintf(mpu_synth_info[m].name, - "MPU-401 %d.%d%c Midi interface #%d", + "MPU-401 %d.%d%c MIDI #%d", (int) (devc->version & 0xf0) >> 4, devc->version & 0x0f, revision_char, -- GitLab From 430453fc2a5f3f2c1d98ebc3c3d4c54f3060e3c3 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Tue, 28 Jul 2009 09:59:47 +0200 Subject: [PATCH 0478/1342] libertas: Read outside array bounds reads bss->rates[j] before checking bounds of index, and should use ARRAY_SIZE to determine the size of the array. Signed-off-by: Roel Kluin Acked-by: Holger Schurig Acked-by: Dan Williams Signed-off-by: John W. Linville --- drivers/net/wireless/libertas/scan.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/net/wireless/libertas/scan.c b/drivers/net/wireless/libertas/scan.c index 601b5424967..6c95af3023c 100644 --- a/drivers/net/wireless/libertas/scan.c +++ b/drivers/net/wireless/libertas/scan.c @@ -5,6 +5,7 @@ * for sending scan commands to the firmware. */ #include +#include #include #include #include @@ -876,7 +877,7 @@ static inline char *lbs_translate_scan(struct lbs_private *priv, iwe.u.bitrate.disabled = 0; iwe.u.bitrate.value = 0; - for (j = 0; bss->rates[j] && (j < sizeof(bss->rates)); j++) { + for (j = 0; j < ARRAY_SIZE(bss->rates) && bss->rates[j]; j++) { /* Bit rate given in 500 kb/s units */ iwe.u.bitrate.value = bss->rates[j] * 500000; current_val = iwe_stream_add_value(info, start, current_val, -- GitLab From 57921c312e8cef72ba35a4cfe870b376da0b1b87 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Tue, 28 Jul 2009 12:05:00 +0200 Subject: [PATCH 0479/1342] libertas: Read buffer overflow Several arrays were read before checking whether the index was within bounds. ARRAY_SIZE() should be used to determine the size of arrays. rates->rates has an arraysize of 1, so calling get_common_rates() with a rates_size of MAX_RATES (14) was causing reads out of bounds. tmp_size can increment at most to (ARRAY_SIZE(lbs_bg_rates) - 1) * (*rates_size - 1), so that should be the number of elements of tmp[]. A goto can be eliminated: ret was already set upon its declaration. Signed-off-by: Roel Kluin Signed-off-by: John W. Linville --- drivers/net/wireless/libertas/assoc.c | 18 ++++++++---------- 1 file changed, 8 insertions(+), 10 deletions(-) diff --git a/drivers/net/wireless/libertas/assoc.c b/drivers/net/wireless/libertas/assoc.c index b9b37411903..d6997371c27 100644 --- a/drivers/net/wireless/libertas/assoc.c +++ b/drivers/net/wireless/libertas/assoc.c @@ -1,6 +1,7 @@ /* Copyright (C) 2006, Red Hat, Inc. */ #include +#include #include #include #include @@ -43,21 +44,21 @@ static int get_common_rates(struct lbs_private *priv, u16 *rates_size) { u8 *card_rates = lbs_bg_rates; - size_t num_card_rates = sizeof(lbs_bg_rates); int ret = 0, i, j; - u8 tmp[30]; + u8 tmp[(ARRAY_SIZE(lbs_bg_rates) - 1) * (*rates_size - 1)]; size_t tmp_size = 0; /* For each rate in card_rates that exists in rate1, copy to tmp */ - for (i = 0; card_rates[i] && (i < num_card_rates); i++) { - for (j = 0; rates[j] && (j < *rates_size); j++) { + for (i = 0; i < ARRAY_SIZE(lbs_bg_rates) && card_rates[i]; i++) { + for (j = 0; j < *rates_size && rates[j]; j++) { if (rates[j] == card_rates[i]) tmp[tmp_size++] = card_rates[i]; } } lbs_deb_hex(LBS_DEB_JOIN, "AP rates ", rates, *rates_size); - lbs_deb_hex(LBS_DEB_JOIN, "card rates ", card_rates, num_card_rates); + lbs_deb_hex(LBS_DEB_JOIN, "card rates ", card_rates, + ARRAY_SIZE(lbs_bg_rates)); lbs_deb_hex(LBS_DEB_JOIN, "common rates", tmp, tmp_size); lbs_deb_join("TX data rate 0x%02x\n", priv->cur_rate); @@ -69,10 +70,7 @@ static int get_common_rates(struct lbs_private *priv, lbs_pr_alert("Previously set fixed data rate %#x isn't " "compatible with the network.\n", priv->cur_rate); ret = -1; - goto done; } - ret = 0; - done: memset(rates, 0, *rates_size); *rates_size = min_t(int, tmp_size, *rates_size); @@ -322,7 +320,7 @@ static int lbs_associate(struct lbs_private *priv, rates = (struct mrvl_ie_rates_param_set *) pos; rates->header.type = cpu_to_le16(TLV_TYPE_RATES); memcpy(&rates->rates, &bss->rates, MAX_RATES); - tmplen = MAX_RATES; + tmplen = min_t(u16, ARRAY_SIZE(rates->rates), MAX_RATES); if (get_common_rates(priv, rates->rates, &tmplen)) { ret = -1; goto done; @@ -598,7 +596,7 @@ static int lbs_adhoc_join(struct lbs_private *priv, /* Copy Data rates from the rates recorded in scan response */ memset(cmd.bss.rates, 0, sizeof(cmd.bss.rates)); - ratesize = min_t(u16, sizeof(cmd.bss.rates), MAX_RATES); + ratesize = min_t(u16, ARRAY_SIZE(cmd.bss.rates), MAX_RATES); memcpy(cmd.bss.rates, bss->rates, ratesize); if (get_common_rates(priv, cmd.bss.rates, &ratesize)) { lbs_deb_join("ADHOC_JOIN: get_common_rates returned error.\n"); -- GitLab From 89c3a8aca28e6d57f2ae945d97858a372d624b81 Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Tue, 28 Jul 2009 18:10:17 +0200 Subject: [PATCH 0480/1342] mac80211: fix suspend Jan reported that his b43-based laptop hangs during suspend. The problem turned out to be mac80211 asking the driver to stop the hardware before removing interfaces, and interface removal caused b43 to touch the hardware (while down, which causes the hang). This patch fixes mac80211 to do reorder these operations to have them in the correct order -- first remove interfaces and then stop the hardware. Some more code is necessary to be able to do so in a race-free manner, in particular it is necessary to not process frames received during quiescing. Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13337. Reported-by: Jan Scholz Signed-off-by: Johannes Berg Signed-off-by: John W. Linville --- net/mac80211/pm.c | 24 +++++++++++++++--------- net/mac80211/rx.c | 12 ++++++++++++ 2 files changed, 27 insertions(+), 9 deletions(-) diff --git a/net/mac80211/pm.c b/net/mac80211/pm.c index 7a549f9deb9..5e3d476972f 100644 --- a/net/mac80211/pm.c +++ b/net/mac80211/pm.c @@ -55,15 +55,6 @@ int __ieee80211_suspend(struct ieee80211_hw *hw) rcu_read_unlock(); - /* flush again, in case driver queued work */ - flush_workqueue(local->hw.workqueue); - - /* stop hardware - this must stop RX */ - if (local->open_count) { - ieee80211_led_radio(local, false); - drv_stop(local); - } - /* remove STAs */ spin_lock_irqsave(&local->sta_lock, flags); list_for_each_entry(sta, &local->sta_list, list) { @@ -111,7 +102,22 @@ int __ieee80211_suspend(struct ieee80211_hw *hw) drv_remove_interface(local, &conf); } + /* stop hardware - this must stop RX */ + if (local->open_count) { + ieee80211_led_radio(local, false); + drv_stop(local); + } + + /* + * flush again, in case driver queued work -- it + * shouldn't be doing (or cancel everything in the + * stop callback) that but better safe than sorry. + */ + flush_workqueue(local->hw.workqueue); + local->suspended = true; + /* need suspended to be visible before quiescing is false */ + barrier(); local->quiescing = false; return 0; diff --git a/net/mac80211/rx.c b/net/mac80211/rx.c index de5bba7f910..0936fc24942 100644 --- a/net/mac80211/rx.c +++ b/net/mac80211/rx.c @@ -2453,6 +2453,18 @@ void __ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb, return; } + /* + * If we're suspending, it is possible although not too likely + * that we'd be receiving frames after having already partially + * quiesced the stack. We can't process such frames then since + * that might, for example, cause stations to be added or other + * driver callbacks be invoked. + */ + if (unlikely(local->quiescing || local->suspended)) { + kfree_skb(skb); + return; + } + if (status->flag & RX_FLAG_HT) { /* rate_idx is MCS index */ if (WARN_ON(status->rate_idx < 0 || -- GitLab From ec79be26875f6c1468784876cb99192b7f41c7a5 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Wed, 29 Jul 2009 21:07:47 +0200 Subject: [PATCH 0481/1342] PM / ACPI: HP G7000 Notebook needs a SCI_EN resume quirk This fixes regression (battery "vanishing" on resume) introduced by commit d0c71fe7ebc180f1b7bc7da1d39a07fc19eec768 ("ACPI Suspend: Enable ACPI during resume if SCI_EN is not set") and also the issue with the "screaming" IRQ 9. Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13745 Reported-and-tested-by: Alan Jenkins Cc: stable@kernel.org Signed-off-by: Bartlomiej Zolnierkiewicz Acked-by: Len Brown Signed-off-by: Rafael J. Wysocki --- drivers/acpi/sleep.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/drivers/acpi/sleep.c b/drivers/acpi/sleep.c index 01574a06653..42159a28f43 100644 --- a/drivers/acpi/sleep.c +++ b/drivers/acpi/sleep.c @@ -397,6 +397,14 @@ static struct dmi_system_id __initdata acpisleep_dmi_table[] = { }, }, { + .callback = init_set_sci_en_on_resume, + .ident = "Hewlett-Packard HP G7000 Notebook PC", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"), + DMI_MATCH(DMI_PRODUCT_NAME, "HP G7000 Notebook PC"), + }, + }, + { .callback = init_old_suspend_ordering, .ident = "Panasonic CF51-2L", .matches = { -- GitLab From dddac6a7b445de95515f64fdf82fe5dc36c02f26 Mon Sep 17 00:00:00 2001 From: Alan Jenkins Date: Wed, 29 Jul 2009 21:07:55 +0200 Subject: [PATCH 0482/1342] PM / Hibernate: Replace bdget call with simple atomic_inc of i_count Create bdgrab(). This function copies an existing reference to a block_device. It is safe to call from any context. Hibernation code wishes to copy a reference to the active swap device. Right now it calls bdget() under a spinlock, but this is wrong because bdget() can sleep. It doesn't need a full bdget() because we already hold a reference to active swap devices (and the spinlock protects against swapoff). Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13827 Signed-off-by: Alan Jenkins Signed-off-by: Rafael J. Wysocki --- fs/block_dev.c | 10 ++++++++++ include/linux/fs.h | 1 + mm/swapfile.c | 4 ++-- 3 files changed, 13 insertions(+), 2 deletions(-) diff --git a/fs/block_dev.c b/fs/block_dev.c index 3a6d4fb2a32..94dfda24c06 100644 --- a/fs/block_dev.c +++ b/fs/block_dev.c @@ -564,6 +564,16 @@ struct block_device *bdget(dev_t dev) EXPORT_SYMBOL(bdget); +/** + * bdgrab -- Grab a reference to an already referenced block device + * @bdev: Block device to grab a reference to. + */ +struct block_device *bdgrab(struct block_device *bdev) +{ + atomic_inc(&bdev->bd_inode->i_count); + return bdev; +} + long nr_blockdev_pages(void) { struct block_device *bdev; diff --git a/include/linux/fs.h b/include/linux/fs.h index 0872372184f..a36ffa5a77a 100644 --- a/include/linux/fs.h +++ b/include/linux/fs.h @@ -1946,6 +1946,7 @@ extern void putname(const char *name); extern int register_blkdev(unsigned int, const char *); extern void unregister_blkdev(unsigned int, const char *); extern struct block_device *bdget(dev_t); +extern struct block_device *bdgrab(struct block_device *bdev); extern void bd_set_size(struct block_device *, loff_t size); extern void bd_forget(struct inode *inode); extern void bdput(struct block_device *); diff --git a/mm/swapfile.c b/mm/swapfile.c index d1ade1a48ee..8ffdc0d23c5 100644 --- a/mm/swapfile.c +++ b/mm/swapfile.c @@ -753,7 +753,7 @@ int swap_type_of(dev_t device, sector_t offset, struct block_device **bdev_p) if (!bdev) { if (bdev_p) - *bdev_p = bdget(sis->bdev->bd_dev); + *bdev_p = bdgrab(sis->bdev); spin_unlock(&swap_lock); return i; @@ -765,7 +765,7 @@ int swap_type_of(dev_t device, sector_t offset, struct block_device **bdev_p) struct swap_extent, list); if (se->start_block == offset) { if (bdev_p) - *bdev_p = bdget(sis->bdev->bd_dev); + *bdev_p = bdgrab(sis->bdev); spin_unlock(&swap_lock); bdput(bdev); -- GitLab From e043e42bdb66885b3ac10d27a01ccb9972e2b0a3 Mon Sep 17 00:00:00 2001 From: OGAWA Hirofumi Date: Wed, 29 Jul 2009 12:15:56 -0700 Subject: [PATCH 0483/1342] pty: avoid forcing 'low_latency' tty flag We really don't want to mark the pty as a low-latency device, because as Alan points out, the ->write method can be called from an IRQ (ppp?), and that means we can't use ->low_latency=1 as we take mutexes in the low_latency case. So rather than using low_latency to force the written data to be pushed to the ldisc handling at 'write()' time, just make the reader side (or the poll function) do the flush when it checks whether there is data to be had. This also fixes the problem with lost data in an emacs compile buffer (bugzilla 13815), and we can thus revert the low_latency pty hack (commit 3a54297478e6578f96fd54bf4daa1751130aca86: "pty: quickfix for the pty ENXIO timing problems"). Signed-off-by: OGAWA Hirofumi Tested-by: Aneesh Kumar K.V [ Modified to do the tty_flush_to_ldisc() inside input_available_p() so that it triggers for both read and poll() - Linus] Signed-off-by: Linus Torvalds --- drivers/char/n_tty.c | 1 + drivers/char/pty.c | 2 -- drivers/char/tty_buffer.c | 13 +++++++++++++ include/linux/tty.h | 1 + 4 files changed, 15 insertions(+), 2 deletions(-) diff --git a/drivers/char/n_tty.c b/drivers/char/n_tty.c index ff47907ff1b..973be2f4419 100644 --- a/drivers/char/n_tty.c +++ b/drivers/char/n_tty.c @@ -1583,6 +1583,7 @@ static int n_tty_open(struct tty_struct *tty) static inline int input_available_p(struct tty_struct *tty, int amt) { + tty_flush_to_ldisc(tty); if (tty->icanon) { if (tty->canon_data) return 1; diff --git a/drivers/char/pty.c b/drivers/char/pty.c index 3850a68f265..6e6942c45f5 100644 --- a/drivers/char/pty.c +++ b/drivers/char/pty.c @@ -52,7 +52,6 @@ static void pty_close(struct tty_struct *tty, struct file *filp) return; tty->link->packet = 0; set_bit(TTY_OTHER_CLOSED, &tty->link->flags); - tty_flip_buffer_push(tty->link); wake_up_interruptible(&tty->link->read_wait); wake_up_interruptible(&tty->link->write_wait); if (tty->driver->subtype == PTY_TYPE_MASTER) { @@ -208,7 +207,6 @@ static int pty_open(struct tty_struct *tty, struct file *filp) clear_bit(TTY_OTHER_CLOSED, &tty->link->flags); set_bit(TTY_THROTTLED, &tty->flags); retval = 0; - tty->low_latency = 1; out: return retval; } diff --git a/drivers/char/tty_buffer.c b/drivers/char/tty_buffer.c index 810ee25d66a..3108991c5c8 100644 --- a/drivers/char/tty_buffer.c +++ b/drivers/char/tty_buffer.c @@ -461,6 +461,19 @@ static void flush_to_ldisc(struct work_struct *work) tty_ldisc_deref(disc); } +/** + * tty_flush_to_ldisc + * @tty: tty to push + * + * Push the terminal flip buffers to the line discipline. + * + * Must not be called from IRQ context. + */ +void tty_flush_to_ldisc(struct tty_struct *tty) +{ + flush_to_ldisc(&tty->buf.work.work); +} + /** * tty_flip_buffer_push - terminal * @tty: tty to push diff --git a/include/linux/tty.h b/include/linux/tty.h index 1488d8c81aa..e8c6c9136c9 100644 --- a/include/linux/tty.h +++ b/include/linux/tty.h @@ -394,6 +394,7 @@ extern void __do_SAK(struct tty_struct *tty); extern void disassociate_ctty(int priv); extern void no_tty(void); extern void tty_flip_buffer_push(struct tty_struct *tty); +extern void tty_flush_to_ldisc(struct tty_struct *tty); extern void tty_buffer_free_all(struct tty_struct *tty); extern void tty_buffer_flush(struct tty_struct *tty); extern void tty_buffer_init(struct tty_struct *tty); -- GitLab From f5886c7f96f2542382d3a983c5f13e03d7fc5259 Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Wed, 29 Jul 2009 16:26:57 +0100 Subject: [PATCH 0484/1342] kmemleak: Protect the seq start/next/stop sequence by rcu_read_lock() Objects passed to kmemleak_seq_next() have an incremented reference count (hence not freed) but they may point via object_list.next to other freed objects. To avoid this, the whole start/next/stop sequence must be protected by rcu_read_lock(). Signed-off-by: Catalin Marinas Signed-off-by: Linus Torvalds --- mm/kmemleak.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/mm/kmemleak.c b/mm/kmemleak.c index 5aabd41ffb8..487267310a8 100644 --- a/mm/kmemleak.c +++ b/mm/kmemleak.c @@ -1217,7 +1217,6 @@ static void *kmemleak_seq_start(struct seq_file *seq, loff_t *pos) } object = NULL; out: - rcu_read_unlock(); return object; } @@ -1233,13 +1232,11 @@ static void *kmemleak_seq_next(struct seq_file *seq, void *v, loff_t *pos) ++(*pos); - rcu_read_lock(); list_for_each_continue_rcu(n, &object_list) { next_obj = list_entry(n, struct kmemleak_object, object_list); if (get_object(next_obj)) break; } - rcu_read_unlock(); put_object(prev_obj); return next_obj; @@ -1255,6 +1252,7 @@ static void kmemleak_seq_stop(struct seq_file *seq, void *v) * kmemleak_seq_start may return ERR_PTR if the scan_mutex * waiting was interrupted, so only release it if !IS_ERR. */ + rcu_read_unlock(); mutex_unlock(&scan_mutex); if (v) put_object(v); -- GitLab From cdaa052b05e26d96a990af5d253fd2af5db2b1fc Mon Sep 17 00:00:00 2001 From: Zhao Yakui Date: Tue, 28 Jul 2009 10:54:13 +0800 Subject: [PATCH 0485/1342] drm/I915: Fix offset to DVO timings in LVDS data Now the DVO timing in LVDS data entry is obtained by using the following step: a. get the entry size for every LVDS panel data b. Get the LVDS fp entry for the preferred panel type c. get the DVO timing by using entry->dvo_timing In our driver the entry->dvo_timing is related with the size of lvds_fp_timing. For example: the size is 46. But it seems that the size of lvds_fp_timing varies on the differnt platform. In such case we will get the incorrect DVO timing entry because of the incorrect DVO offset in LVDS panel data entry. This also removes a hack on new IGDNG to get proper DVO timing. Calculate the DVO timing offset in LVDS data entry to get the DVO timing a. get the DVO timing offset in the LVDS fp data entry by using the pointer definition in LVDS data ptr b. get the LVDS data entry c. get the DVO timing by adding the DVO timing offset to data entry https://bugs.freedesktop.org/show_bug.cgi?id=22787 Signed-off-by: Zhao Yakui Tested-by: Zhenyu Wang Acked-by: Jesse Barnes Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_bios.c | 19 ++++++++++--------- 1 file changed, 10 insertions(+), 9 deletions(-) diff --git a/drivers/gpu/drm/i915/intel_bios.c b/drivers/gpu/drm/i915/intel_bios.c index 7cc44719102..5c7a62a96ae 100644 --- a/drivers/gpu/drm/i915/intel_bios.c +++ b/drivers/gpu/drm/i915/intel_bios.c @@ -97,14 +97,13 @@ static void parse_lfp_panel_data(struct drm_i915_private *dev_priv, struct bdb_header *bdb) { - struct drm_device *dev = dev_priv->dev; struct bdb_lvds_options *lvds_options; struct bdb_lvds_lfp_data *lvds_lfp_data; struct bdb_lvds_lfp_data_ptrs *lvds_lfp_data_ptrs; struct bdb_lvds_lfp_data_entry *entry; struct lvds_dvo_timing *dvo_timing; struct drm_display_mode *panel_fixed_mode; - int lfp_data_size; + int lfp_data_size, dvo_timing_offset; /* Defaults if we can't find VBT info */ dev_priv->lvds_dither = 0; @@ -133,14 +132,16 @@ parse_lfp_panel_data(struct drm_i915_private *dev_priv, entry = (struct bdb_lvds_lfp_data_entry *) ((uint8_t *)lvds_lfp_data->data + (lfp_data_size * lvds_options->panel_type)); + dvo_timing_offset = lvds_lfp_data_ptrs->ptr[0].dvo_timing_offset - + lvds_lfp_data_ptrs->ptr[0].fp_timing_offset; - /* On IGDNG mobile, LVDS data block removes panel fitting registers. - So dec 2 dword from dvo_timing offset */ - if (IS_IGDNG(dev)) - dvo_timing = (struct lvds_dvo_timing *) - ((u8 *)&entry->dvo_timing - 8); - else - dvo_timing = &entry->dvo_timing; + /* + * the size of fp_timing varies on the different platform. + * So calculate the DVO timing relative offset in LVDS data + * entry to get the DVO timing entry + */ + dvo_timing = (struct lvds_dvo_timing *) + ((unsigned char *)entry + dvo_timing_offset); panel_fixed_mode = kzalloc(sizeof(*panel_fixed_mode), GFP_KERNEL); -- GitLab From 24f119c769bacac5729297b682fec7811a983cc6 Mon Sep 17 00:00:00 2001 From: Zhenyu Wang Date: Fri, 24 Jul 2009 01:00:28 +0800 Subject: [PATCH 0486/1342] drm/i915: disable VGA plane reliably This does VGA disable like DDX driver. SR01 bit 5 should be set before VGA plane disable through control register, otherwise we might get random crash and lockups. Signed-off-by: Zhenyu Wang Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_display.c | 28 +++++++++++++++++++++++++--- 1 file changed, 25 insertions(+), 3 deletions(-) diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index a58bfadabd6..b06364ed259 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -998,6 +998,29 @@ intel_pipe_set_base(struct drm_crtc *crtc, int x, int y, return 0; } +/* Disable the VGA plane that we never use */ +static void i915_disable_vga (struct drm_device *dev) +{ + struct drm_i915_private *dev_priv = dev->dev_private; + u8 sr1; + u32 vga_reg; + + if (IS_IGDNG(dev)) + vga_reg = CPU_VGACNTRL; + else + vga_reg = VGACNTRL; + + if (I915_READ(vga_reg) & VGA_DISP_DISABLE) + return; + + I915_WRITE8(VGA_SR_INDEX, 1); + sr1 = I915_READ8(VGA_SR_DATA); + I915_WRITE8(VGA_SR_DATA, sr1 | (1 << 5)); + udelay(100); + + I915_WRITE(vga_reg, VGA_DISP_DISABLE); +} + static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) { struct drm_device *dev = crtc->dev; @@ -1200,8 +1223,7 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) case DRM_MODE_DPMS_OFF: DRM_DEBUG("crtc %d dpms off\n", pipe); - /* Disable the VGA plane that we never use */ - I915_WRITE(CPU_VGACNTRL, VGA_DISP_DISABLE); + i915_disable_vga(dev); /* Disable display plane */ temp = I915_READ(dspcntr_reg); @@ -1342,7 +1364,7 @@ static void i9xx_crtc_dpms(struct drm_crtc *crtc, int mode) //intel_crtc_dpms_video(crtc, FALSE); TODO /* Disable the VGA plane that we never use */ - I915_WRITE(VGACNTRL, VGA_DISP_DISABLE); + i915_disable_vga(dev); /* Disable display plane */ temp = I915_READ(dspcntr_reg); -- GitLab From 249c0e64c24bf455a4e4815f72750f2b16cedd94 Mon Sep 17 00:00:00 2001 From: Zhenyu Wang Date: Fri, 24 Jul 2009 01:00:29 +0800 Subject: [PATCH 0487/1342] drm/i915: fix issue in display pipe setup on IGDNG During pipe DPMS off, instead of busy waiting pipe off, insert delays during wait and don't loop after enough tries which matches spec requirement. Also try to match DPMS on path by disable FDI TX PLL in DPMS off. Disable PF by writing PF_WIN_SZ which really trigger the update. Signed-off-by: Zhenyu Wang Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/i915_reg.h | 2 + drivers/gpu/drm/i915/intel_display.c | 56 ++++++++++++++++++++++------ 2 files changed, 46 insertions(+), 12 deletions(-) diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h index 897a116cad1..7c77c4c53c5 100644 --- a/drivers/gpu/drm/i915/i915_reg.h +++ b/drivers/gpu/drm/i915/i915_reg.h @@ -1848,6 +1848,8 @@ #define PFA_CTL_1 0x68080 #define PFB_CTL_1 0x68880 #define PF_ENABLE (1<<31) +#define PFA_WIN_SZ 0x68074 +#define PFB_WIN_SZ 0x68874 /* legacy palette */ #define LGC_PALETTE_A 0x4a000 diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index b06364ed259..15a8c3908ac 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -1038,6 +1038,7 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) int fdi_rx_imr_reg = (pipe == 0) ? FDI_RXA_IMR : FDI_RXB_IMR; int transconf_reg = (pipe == 0) ? TRANSACONF : TRANSBCONF; int pf_ctl_reg = (pipe == 0) ? PFA_CTL_1 : PFB_CTL_1; + int pf_win_size = (pipe == 0) ? PFA_WIN_SZ : PFB_WIN_SZ; int cpu_htot_reg = (pipe == 0) ? HTOTAL_A : HTOTAL_B; int cpu_hblank_reg = (pipe == 0) ? HBLANK_A : HBLANK_B; int cpu_hsync_reg = (pipe == 0) ? HSYNC_A : HSYNC_B; @@ -1051,7 +1052,7 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) int trans_vblank_reg = (pipe == 0) ? TRANS_VBLANK_A : TRANS_VBLANK_B; int trans_vsync_reg = (pipe == 0) ? TRANS_VSYNC_A : TRANS_VSYNC_B; u32 temp; - int tries = 5, j; + int tries = 5, j, n; /* XXX: When our outputs are all unaware of DPMS modes other than off * and on, we should map those modes to DRM_MODE_DPMS_OFF in the CRTC. @@ -1239,19 +1240,21 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) if ((temp & PIPEACONF_ENABLE) != 0) { I915_WRITE(pipeconf_reg, temp & ~PIPEACONF_ENABLE); I915_READ(pipeconf_reg); + n = 0; /* wait for cpu pipe off, pipe state */ - while ((I915_READ(pipeconf_reg) & I965_PIPECONF_ACTIVE) != 0) - ; + while ((I915_READ(pipeconf_reg) & I965_PIPECONF_ACTIVE) != 0) { + n++; + if (n < 60) { + udelay(500); + continue; + } else { + DRM_DEBUG("pipe %d off delay\n", pipe); + break; + } + } } else DRM_DEBUG("crtc %d is disabled\n", pipe); - /* IGDNG-A : disable cpu panel fitter ? */ - temp = I915_READ(pf_ctl_reg); - if ((temp & PF_ENABLE) != 0) { - I915_WRITE(pf_ctl_reg, temp & ~PF_ENABLE); - I915_READ(pf_ctl_reg); - } - /* disable CPU FDI tx and PCH FDI rx */ temp = I915_READ(fdi_tx_reg); I915_WRITE(fdi_tx_reg, temp & ~FDI_TX_ENABLE); @@ -1261,6 +1264,8 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) I915_WRITE(fdi_rx_reg, temp & ~FDI_RX_ENABLE); I915_READ(fdi_rx_reg); + udelay(100); + /* still set train pattern 1 */ temp = I915_READ(fdi_tx_reg); temp &= ~FDI_LINK_TRAIN_NONE; @@ -1272,14 +1277,25 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) temp |= FDI_LINK_TRAIN_PATTERN_1; I915_WRITE(fdi_rx_reg, temp); + udelay(100); + /* disable PCH transcoder */ temp = I915_READ(transconf_reg); if ((temp & TRANS_ENABLE) != 0) { I915_WRITE(transconf_reg, temp & ~TRANS_ENABLE); I915_READ(transconf_reg); + n = 0; /* wait for PCH transcoder off, transcoder state */ - while ((I915_READ(transconf_reg) & TRANS_STATE_ENABLE) != 0) - ; + while ((I915_READ(transconf_reg) & TRANS_STATE_ENABLE) != 0) { + n++; + if (n < 60) { + udelay(500); + continue; + } else { + DRM_DEBUG("transcoder %d off delay\n", pipe); + break; + } + } } /* disable PCH DPLL */ @@ -1297,6 +1313,22 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) I915_READ(fdi_rx_reg); } + /* Disable CPU FDI TX PLL */ + temp = I915_READ(fdi_tx_reg); + if ((temp & FDI_TX_PLL_ENABLE) != 0) { + I915_WRITE(fdi_tx_reg, temp & ~FDI_TX_PLL_ENABLE); + I915_READ(fdi_tx_reg); + udelay(100); + } + + /* Disable PF */ + temp = I915_READ(pf_ctl_reg); + if ((temp & PF_ENABLE) != 0) { + I915_WRITE(pf_ctl_reg, temp & ~PF_ENABLE); + I915_READ(pf_ctl_reg); + } + I915_WRITE(pf_win_size, 0); + /* Wait for the clocks to turn off. */ udelay(150); break; -- GitLab From eebc863e469cd91d96c4e3636450596ae29f0502 Mon Sep 17 00:00:00 2001 From: Zhenyu Wang Date: Fri, 24 Jul 2009 01:00:30 +0800 Subject: [PATCH 0488/1342] drm/i915: Fix channel ending action for DP aux transaction We should use current channel 'status' bits to clear DP aux channel's done and error bits, instead of using the channel setting bits, that will set send/busy bit again to initiate new transaction. This also includes also some minor cleanup. Signed-off-by: Zhenyu Wang Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_dp.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c index 6770ae88370..afec65c5ad8 100644 --- a/drivers/gpu/drm/i915/intel_dp.c +++ b/drivers/gpu/drm/i915/intel_dp.c @@ -236,7 +236,7 @@ intel_dp_aux_ch(struct intel_output *intel_output, } /* Clear done status and any errors */ - I915_WRITE(ch_ctl, (ctl | + I915_WRITE(ch_ctl, (status | DP_AUX_CH_CTL_DONE | DP_AUX_CH_CTL_TIME_OUT_ERROR | DP_AUX_CH_CTL_RECEIVE_ERROR)); @@ -295,7 +295,7 @@ intel_dp_aux_native_write(struct intel_output *intel_output, return -1; msg[0] = AUX_NATIVE_WRITE << 4; msg[1] = address >> 8; - msg[2] = address; + msg[2] = address & 0xff; msg[3] = send_bytes - 1; memcpy(&msg[4], send, send_bytes); msg_bytes = send_bytes + 4; @@ -387,8 +387,8 @@ intel_dp_i2c_init(struct intel_output *intel_output, const char *name) memset(&dp_priv->adapter, '\0', sizeof (dp_priv->adapter)); dp_priv->adapter.owner = THIS_MODULE; dp_priv->adapter.class = I2C_CLASS_DDC; - strncpy (dp_priv->adapter.name, name, sizeof dp_priv->adapter.name - 1); - dp_priv->adapter.name[sizeof dp_priv->adapter.name - 1] = '\0'; + strncpy (dp_priv->adapter.name, name, sizeof(dp_priv->adapter.name) - 1); + dp_priv->adapter.name[sizeof(dp_priv->adapter.name) - 1] = '\0'; dp_priv->adapter.algo_data = &dp_priv->algo; dp_priv->adapter.dev.parent = &intel_output->base.kdev; -- GitLab From 5eb08b69f510fadaba77eb9a1bda0f7299c4ebcc Mon Sep 17 00:00:00 2001 From: Zhenyu Wang Date: Fri, 24 Jul 2009 01:00:31 +0800 Subject: [PATCH 0489/1342] drm/i915: enable DisplayPort support on IGDNG Signed-off-by: Zhenyu Wang Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/i915_reg.h | 25 +++++++ drivers/gpu/drm/i915/intel_display.c | 51 +++++++++++++- drivers/gpu/drm/i915/intel_dp.c | 102 ++++++++++++++++++++++----- 3 files changed, 157 insertions(+), 21 deletions(-) diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h index 7c77c4c53c5..4518a9489ed 100644 --- a/drivers/gpu/drm/i915/i915_reg.h +++ b/drivers/gpu/drm/i915/i915_reg.h @@ -1444,6 +1444,7 @@ #define DP_CLOCK_OUTPUT_ENABLE (1 << 13) #define DP_SCRAMBLING_DISABLE (1 << 12) +#define DP_SCRAMBLING_DISABLE_IGDNG (1 << 7) /** limit RGB values to avoid confusing TVs */ #define DP_COLOR_RANGE_16_235 (1 << 8) @@ -2210,4 +2211,28 @@ #define PCH_PP_OFF_DELAYS 0xc720c #define PCH_PP_DIVISOR 0xc7210 +#define PCH_DP_B 0xe4100 +#define PCH_DPB_AUX_CH_CTL 0xe4110 +#define PCH_DPB_AUX_CH_DATA1 0xe4114 +#define PCH_DPB_AUX_CH_DATA2 0xe4118 +#define PCH_DPB_AUX_CH_DATA3 0xe411c +#define PCH_DPB_AUX_CH_DATA4 0xe4120 +#define PCH_DPB_AUX_CH_DATA5 0xe4124 + +#define PCH_DP_C 0xe4200 +#define PCH_DPC_AUX_CH_CTL 0xe4210 +#define PCH_DPC_AUX_CH_DATA1 0xe4214 +#define PCH_DPC_AUX_CH_DATA2 0xe4218 +#define PCH_DPC_AUX_CH_DATA3 0xe421c +#define PCH_DPC_AUX_CH_DATA4 0xe4220 +#define PCH_DPC_AUX_CH_DATA5 0xe4224 + +#define PCH_DP_D 0xe4300 +#define PCH_DPD_AUX_CH_CTL 0xe4310 +#define PCH_DPD_AUX_CH_DATA1 0xe4314 +#define PCH_DPD_AUX_CH_DATA2 0xe4318 +#define PCH_DPD_AUX_CH_DATA3 0xe431c +#define PCH_DPD_AUX_CH_DATA4 0xe4320 +#define PCH_DPD_AUX_CH_DATA5 0xe4324 + #endif /* _I915_REG_H_ */ diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 15a8c3908ac..34c50460eaa 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -268,6 +268,9 @@ intel_igdng_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc, static bool intel_find_pll_g4x_dp(const intel_limit_t *, struct drm_crtc *crtc, int target, int refclk, intel_clock_t *best_clock); +static bool +intel_find_pll_igdng_dp(const intel_limit_t *, struct drm_crtc *crtc, + int target, int refclk, intel_clock_t *best_clock); static const intel_limit_t intel_limits_i8xx_dvo = { .dot = { .min = I8XX_DOT_MIN, .max = I8XX_DOT_MAX }, @@ -751,6 +754,30 @@ intel_g4x_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc, return found; } +static bool +intel_find_pll_igdng_dp(const intel_limit_t *limit, struct drm_crtc *crtc, + int target, int refclk, intel_clock_t *best_clock) +{ + struct drm_device *dev = crtc->dev; + intel_clock_t clock; + if (target < 200000) { + clock.n = 1; + clock.p1 = 2; + clock.p2 = 10; + clock.m1 = 12; + clock.m2 = 9; + } else { + clock.n = 2; + clock.p1 = 1; + clock.p2 = 10; + clock.m1 = 14; + clock.m2 = 8; + } + intel_clock(dev, refclk, &clock); + memcpy(best_clock, &clock, sizeof(intel_clock_t)); + return true; +} + static bool intel_igdng_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc, int target, int refclk, intel_clock_t *best_clock) @@ -763,6 +790,10 @@ intel_igdng_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc, int err_most = 47; found = false; + if (intel_pipe_has_type(crtc, INTEL_OUTPUT_DISPLAYPORT)) + return intel_find_pll_igdng_dp(limit, crtc, target, + refclk, best_clock); + if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS)) { if ((I915_READ(LVDS) & LVDS_CLKB_POWER_MASK) == LVDS_CLKB_POWER_UP) @@ -2136,6 +2167,7 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc, int lvds_reg = LVDS; u32 temp; int sdvo_pixel_multiply; + int target_clock; drm_vblank_pre_modeset(dev, pipe); @@ -2218,11 +2250,18 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc, } /* FDI link */ - if (IS_IGDNG(dev)) + if (IS_IGDNG(dev)) { + /* DP over FDI requires target mode clock + instead of link clock */ + if (is_dp) + target_clock = mode->clock; + else + target_clock = adjusted_mode->clock; igdng_compute_m_n(3, 4, /* lane num 4 */ - adjusted_mode->clock, + target_clock, 270000, /* lane clock */ &m_n); + } if (IS_IGD(dev)) fp = (1 << clock.n) << 16 | clock.m1 << 8 | clock.m2; @@ -3050,6 +3089,8 @@ static void intel_setup_outputs(struct drm_device *dev) found = 0; if (!found) intel_hdmi_init(dev, HDMIB); + if (!found && (I915_READ(PCH_DP_B) & DP_DETECTED)) + intel_dp_init(dev, PCH_DP_B); } if (I915_READ(HDMIC) & PORT_DETECTED) @@ -3058,6 +3099,12 @@ static void intel_setup_outputs(struct drm_device *dev) if (I915_READ(HDMID) & PORT_DETECTED) intel_hdmi_init(dev, HDMID); + if (I915_READ(PCH_DP_C) & DP_DETECTED) + intel_dp_init(dev, PCH_DP_C); + + if (I915_READ(PCH_DP_D) & DP_DETECTED) + intel_dp_init(dev, PCH_DP_D); + } else if (IS_I9XX(dev)) { int found; u32 reg; diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c index afec65c5ad8..0715911cbd8 100644 --- a/drivers/gpu/drm/i915/intel_dp.c +++ b/drivers/gpu/drm/i915/intel_dp.c @@ -206,7 +206,12 @@ intel_dp_aux_ch(struct intel_output *intel_output, * and would like to run at 2MHz. So, take the * hrawclk value and divide by 2 and use that */ - aux_clock_divider = intel_hrawclk(dev) / 2; + /* IGDNG: input clock fixed at 125Mhz, so aux_bit_clk always 62 */ + if (IS_IGDNG(dev)) + aux_clock_divider = 62; + else + aux_clock_divider = intel_hrawclk(dev) / 2; + /* Must try at least 3 times according to DP spec */ for (try = 0; try < 5; try++) { /* Load the send data into the aux channel data registers */ @@ -493,22 +498,40 @@ intel_dp_set_m_n(struct drm_crtc *crtc, struct drm_display_mode *mode, intel_dp_compute_m_n(3, lane_count, mode->clock, adjusted_mode->clock, &m_n); - if (intel_crtc->pipe == 0) { - I915_WRITE(PIPEA_GMCH_DATA_M, - ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) | - m_n.gmch_m); - I915_WRITE(PIPEA_GMCH_DATA_N, - m_n.gmch_n); - I915_WRITE(PIPEA_DP_LINK_M, m_n.link_m); - I915_WRITE(PIPEA_DP_LINK_N, m_n.link_n); + if (IS_IGDNG(dev)) { + if (intel_crtc->pipe == 0) { + I915_WRITE(TRANSA_DATA_M1, + ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) | + m_n.gmch_m); + I915_WRITE(TRANSA_DATA_N1, m_n.gmch_n); + I915_WRITE(TRANSA_DP_LINK_M1, m_n.link_m); + I915_WRITE(TRANSA_DP_LINK_N1, m_n.link_n); + } else { + I915_WRITE(TRANSB_DATA_M1, + ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) | + m_n.gmch_m); + I915_WRITE(TRANSB_DATA_N1, m_n.gmch_n); + I915_WRITE(TRANSB_DP_LINK_M1, m_n.link_m); + I915_WRITE(TRANSB_DP_LINK_N1, m_n.link_n); + } } else { - I915_WRITE(PIPEB_GMCH_DATA_M, - ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) | - m_n.gmch_m); - I915_WRITE(PIPEB_GMCH_DATA_N, - m_n.gmch_n); - I915_WRITE(PIPEB_DP_LINK_M, m_n.link_m); - I915_WRITE(PIPEB_DP_LINK_N, m_n.link_n); + if (intel_crtc->pipe == 0) { + I915_WRITE(PIPEA_GMCH_DATA_M, + ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) | + m_n.gmch_m); + I915_WRITE(PIPEA_GMCH_DATA_N, + m_n.gmch_n); + I915_WRITE(PIPEA_DP_LINK_M, m_n.link_m); + I915_WRITE(PIPEA_DP_LINK_N, m_n.link_n); + } else { + I915_WRITE(PIPEB_GMCH_DATA_M, + ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) | + m_n.gmch_m); + I915_WRITE(PIPEB_GMCH_DATA_N, + m_n.gmch_n); + I915_WRITE(PIPEB_DP_LINK_M, m_n.link_m); + I915_WRITE(PIPEB_DP_LINK_N, m_n.link_n); + } } } @@ -935,6 +958,12 @@ intel_dp_link_down(struct intel_output *intel_output, uint32_t DP) struct drm_i915_private *dev_priv = dev->dev_private; struct intel_dp_priv *dp_priv = intel_output->dev_priv; + DP &= ~DP_LINK_TRAIN_MASK; + I915_WRITE(dp_priv->output_reg, DP | DP_LINK_TRAIN_PAT_IDLE); + POSTING_READ(dp_priv->output_reg); + + udelay(17000); + I915_WRITE(dp_priv->output_reg, DP & ~DP_PORT_EN); POSTING_READ(dp_priv->output_reg); } @@ -978,6 +1007,24 @@ intel_dp_check_link_status(struct intel_output *intel_output) intel_dp_link_train(intel_output, dp_priv->DP, dp_priv->link_configuration); } +static enum drm_connector_status +igdng_dp_detect(struct drm_connector *connector) +{ + struct intel_output *intel_output = to_intel_output(connector); + struct intel_dp_priv *dp_priv = intel_output->dev_priv; + enum drm_connector_status status; + + status = connector_status_disconnected; + if (intel_dp_aux_native_read(intel_output, + 0x000, dp_priv->dpcd, + sizeof (dp_priv->dpcd)) == sizeof (dp_priv->dpcd)) + { + if (dp_priv->dpcd[0] != 0) + status = connector_status_connected; + } + return status; +} + /** * Uses CRT_HOTPLUG_EN and CRT_HOTPLUG_STAT to detect DP connection. * @@ -996,6 +1043,9 @@ intel_dp_detect(struct drm_connector *connector) dp_priv->has_audio = false; + if (IS_IGDNG(dev)) + return igdng_dp_detect(connector); + temp = I915_READ(PORT_HOTPLUG_EN); I915_WRITE(PORT_HOTPLUG_EN, @@ -1106,6 +1156,7 @@ intel_dp_init(struct drm_device *dev, int output_reg) struct drm_connector *connector; struct intel_output *intel_output; struct intel_dp_priv *dp_priv; + const char *name = NULL; intel_output = kcalloc(sizeof(struct intel_output) + sizeof(struct intel_dp_priv), 1, GFP_KERNEL); @@ -1139,9 +1190,22 @@ intel_dp_init(struct drm_device *dev, int output_reg) drm_sysfs_connector_add(connector); /* Set up the DDC bus. */ - intel_dp_i2c_init(intel_output, - (output_reg == DP_B) ? "DPDDC-B" : - (output_reg == DP_C) ? "DPDDC-C" : "DPDDC-D"); + switch (output_reg) { + case DP_B: + case PCH_DP_B: + name = "DPDDC-B"; + break; + case DP_C: + case PCH_DP_C: + name = "DPDDC-C"; + break; + case DP_D: + case PCH_DP_D: + name = "DPDDC-D"; + break; + } + + intel_dp_i2c_init(intel_output, name); intel_output->ddc_bus = &dp_priv->adapter; intel_output->hot_plug = intel_dp_hot_plug; -- GitLab From 32f9d658aee5be09ebdd28fc730630e61d0b46db Mon Sep 17 00:00:00 2001 From: Zhenyu Wang Date: Fri, 24 Jul 2009 01:00:32 +0800 Subject: [PATCH 0490/1342] drm/i915: Add eDP support on IGDNG mobile chip This adds embedded DisplayPort support on next mobile chip which aims to replace origin LVDS port. VBT's driver feature block has been used to determine the type of current internal panel for eDP or LVDS. Currently no panel fitting support for eDP and backlight control would be added in future. Signed-off-by: Zhenyu Wang Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/i915_drv.h | 2 + drivers/gpu/drm/i915/i915_reg.h | 16 + drivers/gpu/drm/i915/intel_bios.c | 21 ++ drivers/gpu/drm/i915/intel_bios.h | 45 +++ drivers/gpu/drm/i915/intel_display.c | 433 +++++++++++++++++---------- drivers/gpu/drm/i915/intel_dp.c | 112 ++++++- drivers/gpu/drm/i915/intel_drv.h | 3 + drivers/gpu/drm/i915/intel_lvds.c | 4 + 8 files changed, 468 insertions(+), 168 deletions(-) diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h index b05b44dd3bf..5f3a259d95e 100644 --- a/drivers/gpu/drm/i915/i915_drv.h +++ b/drivers/gpu/drm/i915/i915_drv.h @@ -219,6 +219,7 @@ typedef struct drm_i915_private { unsigned int lvds_vbt:1; unsigned int int_crt_support:1; unsigned int lvds_use_ssc:1; + unsigned int edp_support:1; int lvds_ssc_freq; struct drm_i915_fence_reg fence_regs[16]; /* assume 965 */ @@ -889,6 +890,7 @@ extern int i915_wait_ring(struct drm_device * dev, int n, const char *caller); IS_I915GM(dev))) #define SUPPORTS_INTEGRATED_HDMI(dev) (IS_G4X(dev) || IS_IGDNG(dev)) #define SUPPORTS_INTEGRATED_DP(dev) (IS_G4X(dev) || IS_IGDNG(dev)) +#define SUPPORTS_EDP(dev) (IS_IGDNG_M(dev)) #define I915_HAS_HOTPLUG(dev) (IS_I945G(dev) || IS_I945GM(dev) || IS_I965G(dev)) /* dsparb controlled by hw only */ #define DSPARB_HWCONTROL(dev) (IS_G4X(dev) || IS_IGDNG(dev)) diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h index 4518a9489ed..2955083aa47 100644 --- a/drivers/gpu/drm/i915/i915_reg.h +++ b/drivers/gpu/drm/i915/i915_reg.h @@ -1395,6 +1395,7 @@ #define TV_V_CHROMA_42 0x684a8 /* Display Port */ +#define DP_A 0x64000 /* eDP */ #define DP_B 0x64100 #define DP_C 0x64200 #define DP_D 0x64300 @@ -1437,9 +1438,17 @@ /* Mystic DPCD version 1.1 special mode */ #define DP_ENHANCED_FRAMING (1 << 18) +/* eDP */ +#define DP_PLL_FREQ_270MHZ (0 << 16) +#define DP_PLL_FREQ_160MHZ (1 << 16) +#define DP_PLL_FREQ_MASK (3 << 16) + /** locked once port is enabled */ #define DP_PORT_REVERSAL (1 << 15) +/* eDP */ +#define DP_PLL_ENABLE (1 << 14) + /** sends the clock on lane 15 of the PEG for debug */ #define DP_CLOCK_OUTPUT_ENABLE (1 << 13) @@ -1464,6 +1473,13 @@ * is 20 bytes in each direction, hence the 5 fixed * data registers */ +#define DPA_AUX_CH_CTL 0x64010 +#define DPA_AUX_CH_DATA1 0x64014 +#define DPA_AUX_CH_DATA2 0x64018 +#define DPA_AUX_CH_DATA3 0x6401c +#define DPA_AUX_CH_DATA4 0x64020 +#define DPA_AUX_CH_DATA5 0x64024 + #define DPB_AUX_CH_CTL 0x64110 #define DPB_AUX_CH_DATA1 0x64114 #define DPB_AUX_CH_DATA2 0x64118 diff --git a/drivers/gpu/drm/i915/intel_bios.c b/drivers/gpu/drm/i915/intel_bios.c index 5c7a62a96ae..300aee3296c 100644 --- a/drivers/gpu/drm/i915/intel_bios.c +++ b/drivers/gpu/drm/i915/intel_bios.c @@ -296,6 +296,25 @@ parse_sdvo_device_mapping(struct drm_i915_private *dev_priv, } return; } + +static void +parse_driver_features(struct drm_i915_private *dev_priv, + struct bdb_header *bdb) +{ + struct drm_device *dev = dev_priv->dev; + struct bdb_driver_features *driver; + + /* set default for chips without eDP */ + if (!SUPPORTS_EDP(dev)) { + dev_priv->edp_support = 0; + return; + } + + driver = find_section(bdb, BDB_DRIVER_FEATURES); + if (driver && driver->lvds_config == BDB_DRIVER_FEATURE_EDP) + dev_priv->edp_support = 1; +} + /** * intel_init_bios - initialize VBIOS settings & find VBT * @dev: DRM device @@ -346,6 +365,8 @@ intel_init_bios(struct drm_device *dev) parse_lfp_panel_data(dev_priv, bdb); parse_sdvo_panel_data(dev_priv, bdb); parse_sdvo_device_mapping(dev_priv, bdb); + parse_driver_features(dev_priv, bdb); + pci_unmap_rom(pdev, bios); return 0; diff --git a/drivers/gpu/drm/i915/intel_bios.h b/drivers/gpu/drm/i915/intel_bios.h index fe72e1c225d..0f8e5f69ac7 100644 --- a/drivers/gpu/drm/i915/intel_bios.h +++ b/drivers/gpu/drm/i915/intel_bios.h @@ -381,6 +381,51 @@ struct bdb_sdvo_lvds_options { } __attribute__((packed)); +#define BDB_DRIVER_FEATURE_NO_LVDS 0 +#define BDB_DRIVER_FEATURE_INT_LVDS 1 +#define BDB_DRIVER_FEATURE_SDVO_LVDS 2 +#define BDB_DRIVER_FEATURE_EDP 3 + +struct bdb_driver_features { + u8 boot_dev_algorithm:1; + u8 block_display_switch:1; + u8 allow_display_switch:1; + u8 hotplug_dvo:1; + u8 dual_view_zoom:1; + u8 int15h_hook:1; + u8 sprite_in_clone:1; + u8 primary_lfp_id:1; + + u16 boot_mode_x; + u16 boot_mode_y; + u8 boot_mode_bpp; + u8 boot_mode_refresh; + + u16 enable_lfp_primary:1; + u16 selective_mode_pruning:1; + u16 dual_frequency:1; + u16 render_clock_freq:1; /* 0: high freq; 1: low freq */ + u16 nt_clone_support:1; + u16 power_scheme_ui:1; /* 0: CUI; 1: 3rd party */ + u16 sprite_display_assign:1; /* 0: secondary; 1: primary */ + u16 cui_aspect_scaling:1; + u16 preserve_aspect_ratio:1; + u16 sdvo_device_power_down:1; + u16 crt_hotplug:1; + u16 lvds_config:2; + u16 tv_hotplug:1; + u16 hdmi_config:2; + + u8 static_display:1; + u8 reserved2:7; + u16 legacy_crt_max_x; + u16 legacy_crt_max_y; + u8 legacy_crt_max_refresh; + + u8 hdmi_termination; + u8 custom_vbt_version; +} __attribute__((packed)); + bool intel_init_bios(struct drm_device *dev); /* diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 34c50460eaa..a9f1307d32d 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -34,6 +34,8 @@ #include "drm_crtc_helper.h" +#define HAS_eDP (intel_pipe_has_type(crtc, INTEL_OUTPUT_EDP)) + bool intel_pipe_has_type (struct drm_crtc *crtc, int type); static void intel_update_watermarks(struct drm_device *dev); @@ -601,6 +603,23 @@ bool intel_pipe_has_type (struct drm_crtc *crtc, int type) return false; } +struct drm_connector * +intel_pipe_get_output (struct drm_crtc *crtc) +{ + struct drm_device *dev = crtc->dev; + struct drm_mode_config *mode_config = &dev->mode_config; + struct drm_connector *l_entry, *ret = NULL; + + list_for_each_entry(l_entry, &mode_config->connector_list, head) { + if (l_entry->encoder && + l_entry->encoder->crtc == crtc) { + ret = l_entry; + break; + } + } + return ret; +} + #define INTELPllInvalid(s) do { /* DRM_DEBUG(s); */ return false; } while (0) /** * Returns whether the given set of divisors are valid for a given refclk with @@ -790,6 +809,10 @@ intel_igdng_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc, int err_most = 47; found = false; + /* eDP has only 2 clock choice, no n/m/p setting */ + if (HAS_eDP) + return true; + if (intel_pipe_has_type(crtc, INTEL_OUTPUT_DISPLAYPORT)) return intel_find_pll_igdng_dp(limit, crtc, target, refclk, best_clock); @@ -1052,6 +1075,67 @@ static void i915_disable_vga (struct drm_device *dev) I915_WRITE(vga_reg, VGA_DISP_DISABLE); } +static void igdng_disable_pll_edp (struct drm_crtc *crtc) +{ + struct drm_device *dev = crtc->dev; + struct drm_i915_private *dev_priv = dev->dev_private; + u32 dpa_ctl; + + DRM_DEBUG("\n"); + dpa_ctl = I915_READ(DP_A); + dpa_ctl &= ~DP_PLL_ENABLE; + I915_WRITE(DP_A, dpa_ctl); +} + +static void igdng_enable_pll_edp (struct drm_crtc *crtc) +{ + struct drm_device *dev = crtc->dev; + struct drm_i915_private *dev_priv = dev->dev_private; + u32 dpa_ctl; + + dpa_ctl = I915_READ(DP_A); + dpa_ctl |= DP_PLL_ENABLE; + I915_WRITE(DP_A, dpa_ctl); + udelay(200); +} + + +static void igdng_set_pll_edp (struct drm_crtc *crtc, int clock) +{ + struct drm_device *dev = crtc->dev; + struct drm_i915_private *dev_priv = dev->dev_private; + u32 dpa_ctl; + + DRM_DEBUG("eDP PLL enable for clock %d\n", clock); + dpa_ctl = I915_READ(DP_A); + dpa_ctl &= ~DP_PLL_FREQ_MASK; + + if (clock < 200000) { + u32 temp; + dpa_ctl |= DP_PLL_FREQ_160MHZ; + /* workaround for 160Mhz: + 1) program 0x4600c bits 15:0 = 0x8124 + 2) program 0x46010 bit 0 = 1 + 3) program 0x46034 bit 24 = 1 + 4) program 0x64000 bit 14 = 1 + */ + temp = I915_READ(0x4600c); + temp &= 0xffff0000; + I915_WRITE(0x4600c, temp | 0x8124); + + temp = I915_READ(0x46010); + I915_WRITE(0x46010, temp | 1); + + temp = I915_READ(0x46034); + I915_WRITE(0x46034, temp | (1 << 24)); + } else { + dpa_ctl |= DP_PLL_FREQ_270MHZ; + } + I915_WRITE(DP_A, dpa_ctl); + + udelay(500); +} + static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) { struct drm_device *dev = crtc->dev; @@ -1093,27 +1177,32 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) case DRM_MODE_DPMS_STANDBY: case DRM_MODE_DPMS_SUSPEND: DRM_DEBUG("crtc %d dpms on\n", pipe); - /* enable PCH DPLL */ - temp = I915_READ(pch_dpll_reg); - if ((temp & DPLL_VCO_ENABLE) == 0) { - I915_WRITE(pch_dpll_reg, temp | DPLL_VCO_ENABLE); - I915_READ(pch_dpll_reg); - } - - /* enable PCH FDI RX PLL, wait warmup plus DMI latency */ - temp = I915_READ(fdi_rx_reg); - I915_WRITE(fdi_rx_reg, temp | FDI_RX_PLL_ENABLE | - FDI_SEL_PCDCLK | - FDI_DP_PORT_WIDTH_X4); /* default 4 lanes */ - I915_READ(fdi_rx_reg); - udelay(200); + if (HAS_eDP) { + /* enable eDP PLL */ + igdng_enable_pll_edp(crtc); + } else { + /* enable PCH DPLL */ + temp = I915_READ(pch_dpll_reg); + if ((temp & DPLL_VCO_ENABLE) == 0) { + I915_WRITE(pch_dpll_reg, temp | DPLL_VCO_ENABLE); + I915_READ(pch_dpll_reg); + } - /* Enable CPU FDI TX PLL, always on for IGDNG */ - temp = I915_READ(fdi_tx_reg); - if ((temp & FDI_TX_PLL_ENABLE) == 0) { - I915_WRITE(fdi_tx_reg, temp | FDI_TX_PLL_ENABLE); - I915_READ(fdi_tx_reg); - udelay(100); + /* enable PCH FDI RX PLL, wait warmup plus DMI latency */ + temp = I915_READ(fdi_rx_reg); + I915_WRITE(fdi_rx_reg, temp | FDI_RX_PLL_ENABLE | + FDI_SEL_PCDCLK | + FDI_DP_PORT_WIDTH_X4); /* default 4 lanes */ + I915_READ(fdi_rx_reg); + udelay(200); + + /* Enable CPU FDI TX PLL, always on for IGDNG */ + temp = I915_READ(fdi_tx_reg); + if ((temp & FDI_TX_PLL_ENABLE) == 0) { + I915_WRITE(fdi_tx_reg, temp | FDI_TX_PLL_ENABLE); + I915_READ(fdi_tx_reg); + udelay(100); + } } /* Enable CPU pipe */ @@ -1132,122 +1221,126 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) I915_WRITE(dspbase_reg, I915_READ(dspbase_reg)); } - /* enable CPU FDI TX and PCH FDI RX */ - temp = I915_READ(fdi_tx_reg); - temp |= FDI_TX_ENABLE; - temp |= FDI_DP_PORT_WIDTH_X4; /* default */ - temp &= ~FDI_LINK_TRAIN_NONE; - temp |= FDI_LINK_TRAIN_PATTERN_1; - I915_WRITE(fdi_tx_reg, temp); - I915_READ(fdi_tx_reg); + if (!HAS_eDP) { + /* enable CPU FDI TX and PCH FDI RX */ + temp = I915_READ(fdi_tx_reg); + temp |= FDI_TX_ENABLE; + temp |= FDI_DP_PORT_WIDTH_X4; /* default */ + temp &= ~FDI_LINK_TRAIN_NONE; + temp |= FDI_LINK_TRAIN_PATTERN_1; + I915_WRITE(fdi_tx_reg, temp); + I915_READ(fdi_tx_reg); - temp = I915_READ(fdi_rx_reg); - temp &= ~FDI_LINK_TRAIN_NONE; - temp |= FDI_LINK_TRAIN_PATTERN_1; - I915_WRITE(fdi_rx_reg, temp | FDI_RX_ENABLE); - I915_READ(fdi_rx_reg); + temp = I915_READ(fdi_rx_reg); + temp &= ~FDI_LINK_TRAIN_NONE; + temp |= FDI_LINK_TRAIN_PATTERN_1; + I915_WRITE(fdi_rx_reg, temp | FDI_RX_ENABLE); + I915_READ(fdi_rx_reg); - udelay(150); + udelay(150); - /* Train FDI. */ - /* umask FDI RX Interrupt symbol_lock and bit_lock bit - for train result */ - temp = I915_READ(fdi_rx_imr_reg); - temp &= ~FDI_RX_SYMBOL_LOCK; - temp &= ~FDI_RX_BIT_LOCK; - I915_WRITE(fdi_rx_imr_reg, temp); - I915_READ(fdi_rx_imr_reg); - udelay(150); + /* Train FDI. */ + /* umask FDI RX Interrupt symbol_lock and bit_lock bit + for train result */ + temp = I915_READ(fdi_rx_imr_reg); + temp &= ~FDI_RX_SYMBOL_LOCK; + temp &= ~FDI_RX_BIT_LOCK; + I915_WRITE(fdi_rx_imr_reg, temp); + I915_READ(fdi_rx_imr_reg); + udelay(150); - temp = I915_READ(fdi_rx_iir_reg); - DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp); + temp = I915_READ(fdi_rx_iir_reg); + DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp); - if ((temp & FDI_RX_BIT_LOCK) == 0) { - for (j = 0; j < tries; j++) { - temp = I915_READ(fdi_rx_iir_reg); - DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp); - if (temp & FDI_RX_BIT_LOCK) - break; - udelay(200); - } - if (j != tries) + if ((temp & FDI_RX_BIT_LOCK) == 0) { + for (j = 0; j < tries; j++) { + temp = I915_READ(fdi_rx_iir_reg); + DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp); + if (temp & FDI_RX_BIT_LOCK) + break; + udelay(200); + } + if (j != tries) + I915_WRITE(fdi_rx_iir_reg, + temp | FDI_RX_BIT_LOCK); + else + DRM_DEBUG("train 1 fail\n"); + } else { I915_WRITE(fdi_rx_iir_reg, temp | FDI_RX_BIT_LOCK); - else - DRM_DEBUG("train 1 fail\n"); - } else { - I915_WRITE(fdi_rx_iir_reg, - temp | FDI_RX_BIT_LOCK); - DRM_DEBUG("train 1 ok 2!\n"); - } - temp = I915_READ(fdi_tx_reg); - temp &= ~FDI_LINK_TRAIN_NONE; - temp |= FDI_LINK_TRAIN_PATTERN_2; - I915_WRITE(fdi_tx_reg, temp); - - temp = I915_READ(fdi_rx_reg); - temp &= ~FDI_LINK_TRAIN_NONE; - temp |= FDI_LINK_TRAIN_PATTERN_2; - I915_WRITE(fdi_rx_reg, temp); + DRM_DEBUG("train 1 ok 2!\n"); + } + temp = I915_READ(fdi_tx_reg); + temp &= ~FDI_LINK_TRAIN_NONE; + temp |= FDI_LINK_TRAIN_PATTERN_2; + I915_WRITE(fdi_tx_reg, temp); + + temp = I915_READ(fdi_rx_reg); + temp &= ~FDI_LINK_TRAIN_NONE; + temp |= FDI_LINK_TRAIN_PATTERN_2; + I915_WRITE(fdi_rx_reg, temp); - udelay(150); + udelay(150); - temp = I915_READ(fdi_rx_iir_reg); - DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp); + temp = I915_READ(fdi_rx_iir_reg); + DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp); - if ((temp & FDI_RX_SYMBOL_LOCK) == 0) { - for (j = 0; j < tries; j++) { - temp = I915_READ(fdi_rx_iir_reg); - DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp); - if (temp & FDI_RX_SYMBOL_LOCK) - break; - udelay(200); - } - if (j != tries) { + if ((temp & FDI_RX_SYMBOL_LOCK) == 0) { + for (j = 0; j < tries; j++) { + temp = I915_READ(fdi_rx_iir_reg); + DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp); + if (temp & FDI_RX_SYMBOL_LOCK) + break; + udelay(200); + } + if (j != tries) { + I915_WRITE(fdi_rx_iir_reg, + temp | FDI_RX_SYMBOL_LOCK); + DRM_DEBUG("train 2 ok 1!\n"); + } else + DRM_DEBUG("train 2 fail\n"); + } else { I915_WRITE(fdi_rx_iir_reg, temp | FDI_RX_SYMBOL_LOCK); - DRM_DEBUG("train 2 ok 1!\n"); - } else - DRM_DEBUG("train 2 fail\n"); - } else { - I915_WRITE(fdi_rx_iir_reg, temp | FDI_RX_SYMBOL_LOCK); - DRM_DEBUG("train 2 ok 2!\n"); - } - DRM_DEBUG("train done\n"); + DRM_DEBUG("train 2 ok 2!\n"); + } + DRM_DEBUG("train done\n"); - /* set transcoder timing */ - I915_WRITE(trans_htot_reg, I915_READ(cpu_htot_reg)); - I915_WRITE(trans_hblank_reg, I915_READ(cpu_hblank_reg)); - I915_WRITE(trans_hsync_reg, I915_READ(cpu_hsync_reg)); + /* set transcoder timing */ + I915_WRITE(trans_htot_reg, I915_READ(cpu_htot_reg)); + I915_WRITE(trans_hblank_reg, I915_READ(cpu_hblank_reg)); + I915_WRITE(trans_hsync_reg, I915_READ(cpu_hsync_reg)); - I915_WRITE(trans_vtot_reg, I915_READ(cpu_vtot_reg)); - I915_WRITE(trans_vblank_reg, I915_READ(cpu_vblank_reg)); - I915_WRITE(trans_vsync_reg, I915_READ(cpu_vsync_reg)); + I915_WRITE(trans_vtot_reg, I915_READ(cpu_vtot_reg)); + I915_WRITE(trans_vblank_reg, I915_READ(cpu_vblank_reg)); + I915_WRITE(trans_vsync_reg, I915_READ(cpu_vsync_reg)); - /* enable PCH transcoder */ - temp = I915_READ(transconf_reg); - I915_WRITE(transconf_reg, temp | TRANS_ENABLE); - I915_READ(transconf_reg); + /* enable PCH transcoder */ + temp = I915_READ(transconf_reg); + I915_WRITE(transconf_reg, temp | TRANS_ENABLE); + I915_READ(transconf_reg); - while ((I915_READ(transconf_reg) & TRANS_STATE_ENABLE) == 0) - ; + while ((I915_READ(transconf_reg) & TRANS_STATE_ENABLE) == 0) + ; - /* enable normal */ + /* enable normal */ - temp = I915_READ(fdi_tx_reg); - temp &= ~FDI_LINK_TRAIN_NONE; - I915_WRITE(fdi_tx_reg, temp | FDI_LINK_TRAIN_NONE | - FDI_TX_ENHANCE_FRAME_ENABLE); - I915_READ(fdi_tx_reg); + temp = I915_READ(fdi_tx_reg); + temp &= ~FDI_LINK_TRAIN_NONE; + I915_WRITE(fdi_tx_reg, temp | FDI_LINK_TRAIN_NONE | + FDI_TX_ENHANCE_FRAME_ENABLE); + I915_READ(fdi_tx_reg); - temp = I915_READ(fdi_rx_reg); - temp &= ~FDI_LINK_TRAIN_NONE; - I915_WRITE(fdi_rx_reg, temp | FDI_LINK_TRAIN_NONE | - FDI_RX_ENHANCE_FRAME_ENABLE); - I915_READ(fdi_rx_reg); + temp = I915_READ(fdi_rx_reg); + temp &= ~FDI_LINK_TRAIN_NONE; + I915_WRITE(fdi_rx_reg, temp | FDI_LINK_TRAIN_NONE | + FDI_RX_ENHANCE_FRAME_ENABLE); + I915_READ(fdi_rx_reg); - /* wait one idle pattern time */ - udelay(100); + /* wait one idle pattern time */ + udelay(100); + + } intel_crtc_load_lut(crtc); @@ -1286,6 +1379,10 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) } else DRM_DEBUG("crtc %d is disabled\n", pipe); + if (HAS_eDP) { + igdng_disable_pll_edp(crtc); + } + /* disable CPU FDI tx and PCH FDI rx */ temp = I915_READ(fdi_tx_reg); I915_WRITE(fdi_tx_reg, temp & ~FDI_TX_ENABLE); @@ -2152,6 +2249,7 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc, u32 dpll = 0, fp = 0, dspcntr, pipeconf; bool ok, is_sdvo = false, is_dvo = false; bool is_crt = false, is_lvds = false, is_tv = false, is_dp = false; + bool is_edp = false; struct drm_mode_config *mode_config = &dev->mode_config; struct drm_connector *connector; const intel_limit_t *limit; @@ -2199,6 +2297,9 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc, case INTEL_OUTPUT_DISPLAYPORT: is_dp = true; break; + case INTEL_OUTPUT_EDP: + is_edp = true; + break; } num_outputs++; @@ -2251,16 +2352,27 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc, /* FDI link */ if (IS_IGDNG(dev)) { - /* DP over FDI requires target mode clock - instead of link clock */ - if (is_dp) + int lane, link_bw; + /* eDP doesn't require FDI link, so just set DP M/N + according to current link config */ + if (is_edp) { + struct drm_connector *edp; target_clock = mode->clock; - else - target_clock = adjusted_mode->clock; - igdng_compute_m_n(3, 4, /* lane num 4 */ - target_clock, - 270000, /* lane clock */ - &m_n); + edp = intel_pipe_get_output(crtc); + intel_edp_link_config(to_intel_output(edp), + &lane, &link_bw); + } else { + /* DP over FDI requires target mode clock + instead of link clock */ + if (is_dp) + target_clock = mode->clock; + else + target_clock = adjusted_mode->clock; + lane = 4; + link_bw = 270000; + } + igdng_compute_m_n(3, lane, target_clock, + link_bw, &m_n); } if (IS_IGD(dev)) @@ -2382,29 +2494,15 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc, dpll_reg = pch_dpll_reg; } - if (dpll & DPLL_VCO_ENABLE) { + if (is_edp) { + igdng_disable_pll_edp(crtc); + } else if ((dpll & DPLL_VCO_ENABLE)) { I915_WRITE(fp_reg, fp); I915_WRITE(dpll_reg, dpll & ~DPLL_VCO_ENABLE); I915_READ(dpll_reg); udelay(150); } - if (IS_IGDNG(dev)) { - /* enable PCH clock reference source */ - /* XXX need to change the setting for other outputs */ - u32 temp; - temp = I915_READ(PCH_DREF_CONTROL); - temp &= ~DREF_NONSPREAD_SOURCE_MASK; - temp |= DREF_NONSPREAD_CK505_ENABLE; - temp &= ~DREF_SSC_SOURCE_MASK; - temp |= DREF_SSC_SOURCE_ENABLE; - temp &= ~DREF_SSC1_ENABLE; - /* if no eDP, disable source output to CPU */ - temp &= ~DREF_CPU_SOURCE_OUTPUT_MASK; - temp |= DREF_CPU_SOURCE_OUTPUT_DISABLE; - I915_WRITE(PCH_DREF_CONTROL, temp); - } - /* The LVDS pin pair needs to be on before the DPLLs are enabled. * This is an exception to the general rule that mode_set doesn't turn * things on. @@ -2436,23 +2534,25 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc, if (is_dp) intel_dp_set_m_n(crtc, mode, adjusted_mode); - I915_WRITE(fp_reg, fp); - I915_WRITE(dpll_reg, dpll); - I915_READ(dpll_reg); - /* Wait for the clocks to stabilize. */ - udelay(150); - - if (IS_I965G(dev) && !IS_IGDNG(dev)) { - sdvo_pixel_multiply = adjusted_mode->clock / mode->clock; - I915_WRITE(dpll_md_reg, (0 << DPLL_MD_UDI_DIVIDER_SHIFT) | - ((sdvo_pixel_multiply - 1) << DPLL_MD_UDI_MULTIPLIER_SHIFT)); - } else { - /* write it again -- the BIOS does, after all */ + if (!is_edp) { + I915_WRITE(fp_reg, fp); I915_WRITE(dpll_reg, dpll); + I915_READ(dpll_reg); + /* Wait for the clocks to stabilize. */ + udelay(150); + + if (IS_I965G(dev) && !IS_IGDNG(dev)) { + sdvo_pixel_multiply = adjusted_mode->clock / mode->clock; + I915_WRITE(dpll_md_reg, (0 << DPLL_MD_UDI_DIVIDER_SHIFT) | + ((sdvo_pixel_multiply - 1) << DPLL_MD_UDI_MULTIPLIER_SHIFT)); + } else { + /* write it again -- the BIOS does, after all */ + I915_WRITE(dpll_reg, dpll); + } + I915_READ(dpll_reg); + /* Wait for the clocks to stabilize. */ + udelay(150); } - I915_READ(dpll_reg); - /* Wait for the clocks to stabilize. */ - udelay(150); I915_WRITE(htot_reg, (adjusted_mode->crtc_hdisplay - 1) | ((adjusted_mode->crtc_htotal - 1) << 16)); @@ -2482,10 +2582,14 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc, I915_WRITE(link_m1_reg, m_n.link_m); I915_WRITE(link_n1_reg, m_n.link_n); - /* enable FDI RX PLL too */ - temp = I915_READ(fdi_rx_reg); - I915_WRITE(fdi_rx_reg, temp | FDI_RX_PLL_ENABLE); - udelay(200); + if (is_edp) { + igdng_set_pll_edp(crtc, adjusted_mode->clock); + } else { + /* enable FDI RX PLL too */ + temp = I915_READ(fdi_rx_reg); + I915_WRITE(fdi_rx_reg, temp | FDI_RX_PLL_ENABLE); + udelay(200); + } } I915_WRITE(pipeconf_reg, pipeconf); @@ -3083,6 +3187,9 @@ static void intel_setup_outputs(struct drm_device *dev) if (IS_IGDNG(dev)) { int found; + if (IS_MOBILE(dev) && (I915_READ(DP_A) & DP_DETECTED)) + intel_dp_init(dev, DP_A); + if (I915_READ(HDMIB) & PORT_DETECTED) { /* check SDVOB */ /* found = intel_sdvo_init(dev, HDMIB); */ @@ -3179,6 +3286,10 @@ static void intel_setup_outputs(struct drm_device *dev) (1 << 1)); clone_mask = (1 << INTEL_OUTPUT_DISPLAYPORT); break; + case INTEL_OUTPUT_EDP: + crtc_mask = (1 << 1); + clone_mask = (1 << INTEL_OUTPUT_EDP); + break; } encoder->possible_crtcs = crtc_mask; encoder->possible_clones = intel_connector_clones(dev, clone_mask); diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c index 0715911cbd8..a6ff15ac548 100644 --- a/drivers/gpu/drm/i915/intel_dp.c +++ b/drivers/gpu/drm/i915/intel_dp.c @@ -40,6 +40,8 @@ #define DP_LINK_CONFIGURATION_SIZE 9 +#define IS_eDP(i) ((i)->type == INTEL_OUTPUT_EDP) + struct intel_dp_priv { uint32_t output_reg; uint32_t DP; @@ -63,6 +65,19 @@ intel_dp_link_train(struct intel_output *intel_output, uint32_t DP, static void intel_dp_link_down(struct intel_output *intel_output, uint32_t DP); +void +intel_edp_link_config (struct intel_output *intel_output, + int *lane_num, int *link_bw) +{ + struct intel_dp_priv *dp_priv = intel_output->dev_priv; + + *lane_num = dp_priv->lane_count; + if (dp_priv->link_bw == DP_LINK_BW_1_62) + *link_bw = 162000; + else if (dp_priv->link_bw == DP_LINK_BW_2_7) + *link_bw = 270000; +} + static int intel_dp_max_lane_count(struct intel_output *intel_output) { @@ -206,9 +221,10 @@ intel_dp_aux_ch(struct intel_output *intel_output, * and would like to run at 2MHz. So, take the * hrawclk value and divide by 2 and use that */ - /* IGDNG: input clock fixed at 125Mhz, so aux_bit_clk always 62 */ - if (IS_IGDNG(dev)) - aux_clock_divider = 62; + if (IS_eDP(intel_output)) + aux_clock_divider = 225; /* eDP input clock at 450Mhz */ + else if (IS_IGDNG(dev)) + aux_clock_divider = 62; /* IGDNG: input clock fixed at 125Mhz */ else aux_clock_divider = intel_hrawclk(dev) / 2; @@ -579,8 +595,38 @@ intel_dp_mode_set(struct drm_encoder *encoder, struct drm_display_mode *mode, if (intel_crtc->pipe == 1) dp_priv->DP |= DP_PIPEB_SELECT; + + if (IS_eDP(intel_output)) { + /* don't miss out required setting for eDP */ + dp_priv->DP |= DP_PLL_ENABLE; + if (adjusted_mode->clock < 200000) + dp_priv->DP |= DP_PLL_FREQ_160MHZ; + else + dp_priv->DP |= DP_PLL_FREQ_270MHZ; + } } +static void igdng_edp_backlight_on (struct drm_device *dev) +{ + struct drm_i915_private *dev_priv = dev->dev_private; + u32 pp; + + DRM_DEBUG("\n"); + pp = I915_READ(PCH_PP_CONTROL); + pp |= EDP_BLC_ENABLE; + I915_WRITE(PCH_PP_CONTROL, pp); +} + +static void igdng_edp_backlight_off (struct drm_device *dev) +{ + struct drm_i915_private *dev_priv = dev->dev_private; + u32 pp; + + DRM_DEBUG("\n"); + pp = I915_READ(PCH_PP_CONTROL); + pp &= ~EDP_BLC_ENABLE; + I915_WRITE(PCH_PP_CONTROL, pp); +} static void intel_dp_dpms(struct drm_encoder *encoder, int mode) @@ -592,11 +638,17 @@ intel_dp_dpms(struct drm_encoder *encoder, int mode) uint32_t dp_reg = I915_READ(dp_priv->output_reg); if (mode != DRM_MODE_DPMS_ON) { - if (dp_reg & DP_PORT_EN) + if (dp_reg & DP_PORT_EN) { intel_dp_link_down(intel_output, dp_priv->DP); + if (IS_eDP(intel_output)) + igdng_edp_backlight_off(dev); + } } else { - if (!(dp_reg & DP_PORT_EN)) + if (!(dp_reg & DP_PORT_EN)) { intel_dp_link_train(intel_output, dp_priv->DP, dp_priv->link_configuration); + if (IS_eDP(intel_output)) + igdng_edp_backlight_on(dev); + } } dp_priv->dpms_mode = mode; } @@ -958,12 +1010,23 @@ intel_dp_link_down(struct intel_output *intel_output, uint32_t DP) struct drm_i915_private *dev_priv = dev->dev_private; struct intel_dp_priv *dp_priv = intel_output->dev_priv; + DRM_DEBUG("\n"); + + if (IS_eDP(intel_output)) { + DP &= ~DP_PLL_ENABLE; + I915_WRITE(dp_priv->output_reg, DP); + POSTING_READ(dp_priv->output_reg); + udelay(100); + } + DP &= ~DP_LINK_TRAIN_MASK; I915_WRITE(dp_priv->output_reg, DP | DP_LINK_TRAIN_PAT_IDLE); POSTING_READ(dp_priv->output_reg); udelay(17000); + if (IS_eDP(intel_output)) + DP |= DP_LINK_TRAIN_OFF; I915_WRITE(dp_priv->output_reg, DP & ~DP_PORT_EN); POSTING_READ(dp_priv->output_reg); } @@ -1089,11 +1152,27 @@ intel_dp_detect(struct drm_connector *connector) static int intel_dp_get_modes(struct drm_connector *connector) { struct intel_output *intel_output = to_intel_output(connector); + struct drm_device *dev = intel_output->base.dev; + struct drm_i915_private *dev_priv = dev->dev_private; + int ret; /* We should parse the EDID data and find out if it has an audio sink */ - return intel_ddc_get_modes(intel_output); + ret = intel_ddc_get_modes(intel_output); + if (ret) + return ret; + + /* if eDP has no EDID, try to use fixed panel mode from VBT */ + if (IS_eDP(intel_output)) { + if (dev_priv->panel_fixed_mode != NULL) { + struct drm_display_mode *mode; + mode = drm_mode_duplicate(dev, dev_priv->panel_fixed_mode); + drm_mode_probed_add(connector, mode); + return 1; + } + } + return 0; } static void @@ -1170,7 +1249,10 @@ intel_dp_init(struct drm_device *dev, int output_reg) DRM_MODE_CONNECTOR_DisplayPort); drm_connector_helper_add(connector, &intel_dp_connector_helper_funcs); - intel_output->type = INTEL_OUTPUT_DISPLAYPORT; + if (output_reg == DP_A) + intel_output->type = INTEL_OUTPUT_EDP; + else + intel_output->type = INTEL_OUTPUT_DISPLAYPORT; connector->interlace_allowed = true; connector->doublescan_allowed = 0; @@ -1191,6 +1273,9 @@ intel_dp_init(struct drm_device *dev, int output_reg) /* Set up the DDC bus. */ switch (output_reg) { + case DP_A: + name = "DPDDC-A"; + break; case DP_B: case PCH_DP_B: name = "DPDDC-B"; @@ -1206,9 +1291,22 @@ intel_dp_init(struct drm_device *dev, int output_reg) } intel_dp_i2c_init(intel_output, name); + intel_output->ddc_bus = &dp_priv->adapter; intel_output->hot_plug = intel_dp_hot_plug; + if (output_reg == DP_A) { + /* initialize panel mode from VBT if available for eDP */ + if (dev_priv->lfp_lvds_vbt_mode) { + dev_priv->panel_fixed_mode = + drm_mode_duplicate(dev, dev_priv->lfp_lvds_vbt_mode); + if (dev_priv->panel_fixed_mode) { + dev_priv->panel_fixed_mode->type |= + DRM_MODE_TYPE_PREFERRED; + } + } + } + /* For G4X desktop chip, PEG_BAND_GAP_DATA 3:0 must first be written * 0xd. Failure to do so will result in spurious interrupts being * generated on the port when a cable is not attached. diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h index 004541c935a..d6f92ea1b55 100644 --- a/drivers/gpu/drm/i915/intel_drv.h +++ b/drivers/gpu/drm/i915/intel_drv.h @@ -55,6 +55,7 @@ #define INTEL_OUTPUT_TVOUT 5 #define INTEL_OUTPUT_HDMI 6 #define INTEL_OUTPUT_DISPLAYPORT 7 +#define INTEL_OUTPUT_EDP 8 #define INTEL_DVO_CHIP_NONE 0 #define INTEL_DVO_CHIP_LVDS 1 @@ -121,6 +122,8 @@ extern void intel_dp_init(struct drm_device *dev, int dp_reg); void intel_dp_set_m_n(struct drm_crtc *crtc, struct drm_display_mode *mode, struct drm_display_mode *adjusted_mode); +extern void intel_edp_link_config (struct intel_output *, int *, int *); + extern void intel_crtc_load_lut(struct drm_crtc *crtc); extern void intel_encoder_prepare (struct drm_encoder *encoder); diff --git a/drivers/gpu/drm/i915/intel_lvds.c b/drivers/gpu/drm/i915/intel_lvds.c index 43c7d9aa59c..3f445a80c55 100644 --- a/drivers/gpu/drm/i915/intel_lvds.c +++ b/drivers/gpu/drm/i915/intel_lvds.c @@ -892,6 +892,10 @@ void intel_lvds_init(struct drm_device *dev) if (IS_IGDNG(dev)) { if ((I915_READ(PCH_LVDS) & LVDS_DETECTED) == 0) return; + if (dev_priv->edp_support) { + DRM_DEBUG("disable LVDS for eDP support\n"); + return; + } gpio = PCH_GPIOC; } -- GitLab From 67941da28d59cca6817d35823fcb1e3e4eed030e Mon Sep 17 00:00:00 2001 From: Zhenyu Wang Date: Fri, 24 Jul 2009 01:00:33 +0800 Subject: [PATCH 0491/1342] drm/i915: fix VGA detect on IGDNG Check FORCE_DETECT bit to be clear for the finish of hotplug detect process. Also check possible mono monitor which should also be marked as connected. Signed-off-by: Zhenyu Wang Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_crt.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) diff --git a/drivers/gpu/drm/i915/intel_crt.c b/drivers/gpu/drm/i915/intel_crt.c index d6a1a6e5539..4cf8e2e88a4 100644 --- a/drivers/gpu/drm/i915/intel_crt.c +++ b/drivers/gpu/drm/i915/intel_crt.c @@ -156,6 +156,9 @@ static bool intel_igdng_crt_detect_hotplug(struct drm_connector *connector) temp = adpa = I915_READ(PCH_ADPA); + adpa &= ~ADPA_DAC_ENABLE; + I915_WRITE(PCH_ADPA, adpa); + adpa &= ~ADPA_CRT_HOTPLUG_MASK; adpa |= (ADPA_CRT_HOTPLUG_PERIOD_128 | @@ -169,13 +172,14 @@ static bool intel_igdng_crt_detect_hotplug(struct drm_connector *connector) DRM_DEBUG("pch crt adpa 0x%x", adpa); I915_WRITE(PCH_ADPA, adpa); - /* This might not be needed as not specified in spec...*/ - udelay(1000); + while ((I915_READ(PCH_ADPA) & ADPA_CRT_HOTPLUG_FORCE_TRIGGER) != 0) + ; /* Check the status to see if both blue and green are on now */ adpa = I915_READ(PCH_ADPA); - if ((adpa & ADPA_CRT_HOTPLUG_MONITOR_MASK) == - ADPA_CRT_HOTPLUG_MONITOR_COLOR) + adpa &= ADPA_CRT_HOTPLUG_MONITOR_MASK; + if ((adpa == ADPA_CRT_HOTPLUG_MONITOR_COLOR) || + (adpa == ADPA_CRT_HOTPLUG_MONITOR_MONO)) ret = true; else ret = false; -- GitLab From f360132626b11d0dc60814033873ca0e3111677c Mon Sep 17 00:00:00 2001 From: Jesse Barnes Date: Wed, 22 Jul 2009 12:54:59 -0700 Subject: [PATCH 0492/1342] drm/i915: fix 845G FIFO size & burst length I had one report of flicker due to FIFO underruns on 845G. Scott was kind enough to test a few patches and report success with this one. Looks like 845G measures FIFO size slightly differently than other chips, and we were also clobbering the FIFO burst length. Fixing both of those issues gives him a healthy machine again. Note that we still only adjust plane A's watermark in the 830/845 case. If someone is willing to test we could support a bigger variety of dual-head 830/845 configurations with a bit more code. Fixes fdo bug #19304 (again). Reported-by: Scott Hansen Tested-by: Scott Hansen Signed-off-by: Jesse Barnes Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_display.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index a9f1307d32d..1da7b0b9ed3 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -2026,6 +2026,9 @@ static int intel_get_fifo_size(struct drm_device *dev, int plane) size = ((dsparb >> DSPARB_BEND_SHIFT) & 0x1ff) - (dsparb & 0x1ff); size >>= 1; /* Convert to cachelines */ + } else if (IS_845G(dev)) { + size = dsparb & 0x7f; + size >>= 2; /* Convert to cachelines */ } else { size = dsparb & 0x7f; size >>= 1; /* Convert to cachelines */ @@ -2125,14 +2128,16 @@ static void i830_update_wm(struct drm_device *dev, int planea_clock, int pixel_size) { struct drm_i915_private *dev_priv = dev->dev_private; - uint32_t fwater_lo = I915_READ(FW_BLC) & MM_FIFO_WATERMARK; + uint32_t fwater_lo = I915_READ(FW_BLC) & ~0xfff; int planea_wm; i830_wm_info.fifo_size = intel_get_fifo_size(dev, 0); planea_wm = intel_calculate_wm(planea_clock, &i830_wm_info, pixel_size, latency_ns); - fwater_lo = fwater_lo | planea_wm; + fwater_lo |= (3<<8) | planea_wm; + + DRM_DEBUG("Setting FIFO watermarks - A: %d\n", planea_wm); I915_WRITE(FW_BLC, fwater_lo); } -- GitLab From bcae2ca81c4a085e3e0e8941b7c64f9aeb6fc05c Mon Sep 17 00:00:00 2001 From: "ling.ma@intel.com" Date: Mon, 20 Jul 2009 13:20:23 +0800 Subject: [PATCH 0493/1342] drm/i915: Set preferred mode for integrated TV according to TV format In order to get best possible quality image we chose 640x480 for NTSC, PAL and 480p, 1280x720 for 720p, 1920x1080 for 1080i/p TV format respectively. Signed-off-by: Ma Ling Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_tv.c | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+) diff --git a/drivers/gpu/drm/i915/intel_tv.c b/drivers/gpu/drm/i915/intel_tv.c index a43c98e3f07..da4ab4dc163 100644 --- a/drivers/gpu/drm/i915/intel_tv.c +++ b/drivers/gpu/drm/i915/intel_tv.c @@ -1490,6 +1490,27 @@ static struct input_res { {"1920x1080", 1920, 1080}, }; +/* + * Chose preferred mode according to line number of TV format + */ +static void +intel_tv_chose_preferred_modes(struct drm_connector *connector, + struct drm_display_mode *mode_ptr) +{ + struct intel_output *intel_output = to_intel_output(connector); + const struct tv_mode *tv_mode = intel_tv_mode_find(intel_output); + + if (tv_mode->nbr_end < 480 && mode_ptr->vdisplay == 480) + mode_ptr->type |= DRM_MODE_TYPE_PREFERRED; + else if (tv_mode->nbr_end > 480) { + if (tv_mode->progressive == true && tv_mode->nbr_end < 720) { + if (mode_ptr->vdisplay == 720) + mode_ptr->type |= DRM_MODE_TYPE_PREFERRED; + } else if (mode_ptr->vdisplay == 1080) + mode_ptr->type |= DRM_MODE_TYPE_PREFERRED; + } +} + /** * Stub get_modes function. * @@ -1544,6 +1565,7 @@ intel_tv_get_modes(struct drm_connector *connector) mode_ptr->clock = (int) tmp; mode_ptr->type = DRM_MODE_TYPE_DRIVER; + intel_tv_chose_preferred_modes(connector, mode_ptr); drm_mode_probed_add(connector, mode_ptr); count++; } -- GitLab From fb7a46f3cc7d7dcf7c5edb3a38c84e3f730d7adb Mon Sep 17 00:00:00 2001 From: "ling.ma@intel.com" Date: Thu, 23 Jul 2009 17:11:34 +0800 Subject: [PATCH 0494/1342] drm/i915: Choose real sdvo output according to result from detection Baed on Eric's idea in order to handle multiple sdvo encoders we implement another approach to dynamically chose real one encoder after detection, which is contrasted with patch - drm/i915:Construct all possible sdvo outputs for sdvo encoder. Signed-off-by: Ma Ling Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_sdvo.c | 231 ++++++++++++++++++++---------- 1 file changed, 153 insertions(+), 78 deletions(-) diff --git a/drivers/gpu/drm/i915/intel_sdvo.c b/drivers/gpu/drm/i915/intel_sdvo.c index 4f0c30948bc..b68746f0380 100644 --- a/drivers/gpu/drm/i915/intel_sdvo.c +++ b/drivers/gpu/drm/i915/intel_sdvo.c @@ -55,6 +55,12 @@ struct intel_sdvo_priv { /* Pixel clock limitations reported by the SDVO device, in kHz */ int pixel_clock_min, pixel_clock_max; + /* + * For multiple function SDVO device, + * this is for current attached outputs. + */ + uint16_t attached_output; + /** * This is set if we're going to treat the device as TV-out. * @@ -114,6 +120,9 @@ struct intel_sdvo_priv { u32 save_SDVOX; }; +static bool +intel_sdvo_output_setup(struct intel_output *intel_output, uint16_t flags); + /** * Writes the SDVOB or SDVOC with the given value, but always writes both * SDVOB and SDVOC to work around apparent hardware issues (according to @@ -1435,6 +1444,39 @@ void intel_sdvo_set_hotplug(struct drm_connector *connector, int on) intel_sdvo_read_response(intel_output, &response, 2); } +static bool +intel_sdvo_multifunc_encoder(struct intel_output *intel_output) +{ + struct intel_sdvo_priv *sdvo_priv = intel_output->dev_priv; + int caps = 0; + + if (sdvo_priv->caps.output_flags & + (SDVO_OUTPUT_TMDS0 | SDVO_OUTPUT_TMDS1)) + caps++; + if (sdvo_priv->caps.output_flags & + (SDVO_OUTPUT_RGB0 | SDVO_OUTPUT_RGB1)) + caps++; + if (sdvo_priv->caps.output_flags & + (SDVO_OUTPUT_SVID0 | SDVO_OUTPUT_SVID0)) + caps++; + if (sdvo_priv->caps.output_flags & + (SDVO_OUTPUT_CVBS0 | SDVO_OUTPUT_CVBS1)) + caps++; + if (sdvo_priv->caps.output_flags & + (SDVO_OUTPUT_YPRPB0 | SDVO_OUTPUT_YPRPB1)) + caps++; + + if (sdvo_priv->caps.output_flags & + (SDVO_OUTPUT_SCART0 | SDVO_OUTPUT_SCART1)) + caps++; + + if (sdvo_priv->caps.output_flags & + (SDVO_OUTPUT_LVDS0 | SDVO_OUTPUT_LVDS1)) + caps++; + + return (caps > 1); +} + static void intel_sdvo_hdmi_sink_detect(struct drm_connector *connector) { @@ -1453,23 +1495,31 @@ intel_sdvo_hdmi_sink_detect(struct drm_connector *connector) static enum drm_connector_status intel_sdvo_detect(struct drm_connector *connector) { - u8 response[2]; + uint16_t response; u8 status; struct intel_output *intel_output = to_intel_output(connector); + struct intel_sdvo_priv *sdvo_priv = intel_output->dev_priv; intel_sdvo_write_cmd(intel_output, SDVO_CMD_GET_ATTACHED_DISPLAYS, NULL, 0); status = intel_sdvo_read_response(intel_output, &response, 2); - DRM_DEBUG("SDVO response %d %d\n", response[0], response[1]); + DRM_DEBUG("SDVO response %d %d\n", response & 0xff, response >> 8); if (status != SDVO_CMD_STATUS_SUCCESS) return connector_status_unknown; - if ((response[0] != 0) || (response[1] != 0)) { - intel_sdvo_hdmi_sink_detect(connector); - return connector_status_connected; - } else + if (response == 0) return connector_status_disconnected; + + if (intel_sdvo_multifunc_encoder(intel_output) && + sdvo_priv->attached_output != response) { + if (sdvo_priv->controlled_output != response && + intel_sdvo_output_setup(intel_output, response) != true) + return connector_status_unknown; + sdvo_priv->attached_output = response; + } + intel_sdvo_hdmi_sink_detect(connector); + return connector_status_connected; } static void intel_sdvo_get_ddc_modes(struct drm_connector *connector) @@ -1866,16 +1916,101 @@ intel_sdvo_get_slave_addr(struct drm_device *dev, int output_device) return 0x72; } +static bool +intel_sdvo_output_setup(struct intel_output *intel_output, uint16_t flags) +{ + struct drm_connector *connector = &intel_output->base; + struct drm_encoder *encoder = &intel_output->enc; + struct intel_sdvo_priv *sdvo_priv = intel_output->dev_priv; + bool ret = true, registered = false; + + sdvo_priv->is_tv = false; + intel_output->needs_tv_clock = false; + sdvo_priv->is_lvds = false; + + if (device_is_registered(&connector->kdev)) { + drm_sysfs_connector_remove(connector); + registered = true; + } + + if (flags & + (SDVO_OUTPUT_TMDS0 | SDVO_OUTPUT_TMDS1)) { + if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_TMDS0) + sdvo_priv->controlled_output = SDVO_OUTPUT_TMDS0; + else + sdvo_priv->controlled_output = SDVO_OUTPUT_TMDS1; + + encoder->encoder_type = DRM_MODE_ENCODER_TMDS; + connector->connector_type = DRM_MODE_CONNECTOR_DVID; + + if (intel_sdvo_get_supp_encode(intel_output, + &sdvo_priv->encode) && + intel_sdvo_get_digital_encoding_mode(intel_output) && + sdvo_priv->is_hdmi) { + /* enable hdmi encoding mode if supported */ + intel_sdvo_set_encode(intel_output, SDVO_ENCODE_HDMI); + intel_sdvo_set_colorimetry(intel_output, + SDVO_COLORIMETRY_RGB256); + connector->connector_type = DRM_MODE_CONNECTOR_HDMIA; + } + } else if (flags & SDVO_OUTPUT_SVID0) { + + sdvo_priv->controlled_output = SDVO_OUTPUT_SVID0; + encoder->encoder_type = DRM_MODE_ENCODER_TVDAC; + connector->connector_type = DRM_MODE_CONNECTOR_SVIDEO; + sdvo_priv->is_tv = true; + intel_output->needs_tv_clock = true; + } else if (flags & SDVO_OUTPUT_RGB0) { + + sdvo_priv->controlled_output = SDVO_OUTPUT_RGB0; + encoder->encoder_type = DRM_MODE_ENCODER_DAC; + connector->connector_type = DRM_MODE_CONNECTOR_VGA; + } else if (flags & SDVO_OUTPUT_RGB1) { + + sdvo_priv->controlled_output = SDVO_OUTPUT_RGB1; + encoder->encoder_type = DRM_MODE_ENCODER_DAC; + connector->connector_type = DRM_MODE_CONNECTOR_VGA; + } else if (flags & SDVO_OUTPUT_LVDS0) { + + sdvo_priv->controlled_output = SDVO_OUTPUT_LVDS0; + encoder->encoder_type = DRM_MODE_ENCODER_LVDS; + connector->connector_type = DRM_MODE_CONNECTOR_LVDS; + sdvo_priv->is_lvds = true; + } else if (flags & SDVO_OUTPUT_LVDS1) { + + sdvo_priv->controlled_output = SDVO_OUTPUT_LVDS1; + encoder->encoder_type = DRM_MODE_ENCODER_LVDS; + connector->connector_type = DRM_MODE_CONNECTOR_LVDS; + sdvo_priv->is_lvds = true; + } else { + + unsigned char bytes[2]; + + sdvo_priv->controlled_output = 0; + memcpy(bytes, &sdvo_priv->caps.output_flags, 2); + DRM_DEBUG_KMS(I915_SDVO, + "%s: Unknown SDVO output type (0x%02x%02x)\n", + SDVO_NAME(sdvo_priv), + bytes[0], bytes[1]); + ret = false; + } + + if (ret && registered) + ret = drm_sysfs_connector_add(connector) == 0 ? true : false; + + + return ret; + +} + bool intel_sdvo_init(struct drm_device *dev, int output_device) { struct drm_connector *connector; struct intel_output *intel_output; struct intel_sdvo_priv *sdvo_priv; - int connector_type; u8 ch[0x40]; int i; - int encoder_type; intel_output = kcalloc(sizeof(struct intel_output)+sizeof(struct intel_sdvo_priv), 1, GFP_KERNEL); if (!intel_output) { @@ -1925,88 +2060,28 @@ bool intel_sdvo_init(struct drm_device *dev, int output_device) intel_output->ddc_bus->algo = &intel_sdvo_i2c_bit_algo; /* In defaut case sdvo lvds is false */ - sdvo_priv->is_lvds = false; intel_sdvo_get_capabilities(intel_output, &sdvo_priv->caps); - if (sdvo_priv->caps.output_flags & - (SDVO_OUTPUT_TMDS0 | SDVO_OUTPUT_TMDS1)) { - if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_TMDS0) - sdvo_priv->controlled_output = SDVO_OUTPUT_TMDS0; - else - sdvo_priv->controlled_output = SDVO_OUTPUT_TMDS1; - - encoder_type = DRM_MODE_ENCODER_TMDS; - connector_type = DRM_MODE_CONNECTOR_DVID; - - if (intel_sdvo_get_supp_encode(intel_output, - &sdvo_priv->encode) && - intel_sdvo_get_digital_encoding_mode(intel_output) && - sdvo_priv->is_hdmi) { - /* enable hdmi encoding mode if supported */ - intel_sdvo_set_encode(intel_output, SDVO_ENCODE_HDMI); - intel_sdvo_set_colorimetry(intel_output, - SDVO_COLORIMETRY_RGB256); - connector_type = DRM_MODE_CONNECTOR_HDMIA; - } - } - else if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_SVID0) - { - sdvo_priv->controlled_output = SDVO_OUTPUT_SVID0; - encoder_type = DRM_MODE_ENCODER_TVDAC; - connector_type = DRM_MODE_CONNECTOR_SVIDEO; - sdvo_priv->is_tv = true; - intel_output->needs_tv_clock = true; - } - else if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_RGB0) - { - sdvo_priv->controlled_output = SDVO_OUTPUT_RGB0; - encoder_type = DRM_MODE_ENCODER_DAC; - connector_type = DRM_MODE_CONNECTOR_VGA; - } - else if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_RGB1) - { - sdvo_priv->controlled_output = SDVO_OUTPUT_RGB1; - encoder_type = DRM_MODE_ENCODER_DAC; - connector_type = DRM_MODE_CONNECTOR_VGA; - } - else if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_LVDS0) - { - sdvo_priv->controlled_output = SDVO_OUTPUT_LVDS0; - encoder_type = DRM_MODE_ENCODER_LVDS; - connector_type = DRM_MODE_CONNECTOR_LVDS; - sdvo_priv->is_lvds = true; - } - else if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_LVDS1) - { - sdvo_priv->controlled_output = SDVO_OUTPUT_LVDS1; - encoder_type = DRM_MODE_ENCODER_LVDS; - connector_type = DRM_MODE_CONNECTOR_LVDS; - sdvo_priv->is_lvds = true; - } - else - { - unsigned char bytes[2]; - - sdvo_priv->controlled_output = 0; - memcpy (bytes, &sdvo_priv->caps.output_flags, 2); - DRM_DEBUG_KMS(I915_SDVO, - "%s: Unknown SDVO output type (0x%02x%02x)\n", - SDVO_NAME(sdvo_priv), - bytes[0], bytes[1]); - encoder_type = DRM_MODE_ENCODER_NONE; - connector_type = DRM_MODE_CONNECTOR_Unknown; + if (intel_sdvo_output_setup(intel_output, + sdvo_priv->caps.output_flags) != true) { + DRM_DEBUG("SDVO output failed to setup on SDVO%c\n", + output_device == SDVOB ? 'B' : 'C'); goto err_i2c; } + connector = &intel_output->base; drm_connector_init(dev, connector, &intel_sdvo_connector_funcs, - connector_type); + connector->connector_type); + drm_connector_helper_add(connector, &intel_sdvo_connector_helper_funcs); connector->interlace_allowed = 0; connector->doublescan_allowed = 0; connector->display_info.subpixel_order = SubPixelHorizontalRGB; - drm_encoder_init(dev, &intel_output->enc, &intel_sdvo_enc_funcs, encoder_type); + drm_encoder_init(dev, &intel_output->enc, + &intel_sdvo_enc_funcs, intel_output->enc.encoder_type); + drm_encoder_helper_add(&intel_output->enc, &intel_sdvo_helper_funcs); drm_mode_connector_attach_encoder(&intel_output->base, &intel_output->enc); -- GitLab From 0c997c0eaac8c68fa23719617484dae29bddaedd Mon Sep 17 00:00:00 2001 From: Lars-Peter Clausen Date: Wed, 22 Jul 2009 00:33:06 +0200 Subject: [PATCH 0495/1342] S3C24XX: GPIO: Fix pin range check in s3c_gpiolib_getchip In the s3c_gpiolib_getchip implementation for s3c24xx the check whether a pin is in the gpio banks range is reversed. Thus the function returns NULL for valid pins and the gpio chip if its not valid. As a result gpio states are not saved/restored properly during suspend/resume. Signed-off-by: Ben Dooks --- arch/arm/mach-s3c2410/include/mach/gpio-core.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-s3c2410/include/mach/gpio-core.h b/arch/arm/mach-s3c2410/include/mach/gpio-core.h index 8fe192081d3..f8b879a7973 100644 --- a/arch/arm/mach-s3c2410/include/mach/gpio-core.h +++ b/arch/arm/mach-s3c2410/include/mach/gpio-core.h @@ -28,7 +28,7 @@ static inline struct s3c_gpio_chip *s3c_gpiolib_getchip(unsigned int pin) return NULL; chip = &s3c24xx_gpios[pin/32]; - return (S3C2410_GPIO_OFFSET(pin) > chip->chip.ngpio) ? chip : NULL; + return (S3C2410_GPIO_OFFSET(pin) < chip->chip.ngpio) ? chip : NULL; } #endif /* __ASM_ARCH_GPIO_CORE_H */ -- GitLab From 1d91e1a296244690461a7c36d71710dfbabbc219 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Wed, 15 Jul 2009 13:03:34 +0100 Subject: [PATCH 0496/1342] S3C64XX: Fix get_rate() for ARMCLK If the requested clock is faster than the parent clock then the parent clock is the closest we can get to the request so we need to return that instead of the requested clock. Signed-off-by: Mark Brown Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/s3c6400-clock.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/plat-s3c64xx/s3c6400-clock.c b/arch/arm/plat-s3c64xx/s3c6400-clock.c index 1debc1f9f98..f8165e62247 100644 --- a/arch/arm/plat-s3c64xx/s3c6400-clock.c +++ b/arch/arm/plat-s3c64xx/s3c6400-clock.c @@ -153,7 +153,7 @@ static unsigned long s3c64xx_clk_arm_round_rate(struct clk *clk, u32 div; if (parent < rate) - return rate; + return parent; div = (parent / rate) - 1; if (div > armclk_mask) -- GitLab From 9b71de49b030ad8fd4d13d38571b5c42dc9ed8dd Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Wed, 15 Jul 2009 13:03:35 +0100 Subject: [PATCH 0497/1342] S3C64XX: Fix ARMCLK configuration The value of armclk_mask needs to be inverted for use as a mask on the register value when updating ARM_RATIO. This is critical for cpufreq support, without it attempts to scale the frequency of the core trash pretty much the entire clock tree. Signed-off-by: Mark Brown Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/s3c6400-clock.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/plat-s3c64xx/s3c6400-clock.c b/arch/arm/plat-s3c64xx/s3c6400-clock.c index f8165e62247..febac1950d8 100644 --- a/arch/arm/plat-s3c64xx/s3c6400-clock.c +++ b/arch/arm/plat-s3c64xx/s3c6400-clock.c @@ -175,7 +175,7 @@ static int s3c64xx_clk_arm_set_rate(struct clk *clk, unsigned long rate) div = clk_get_rate(clk->parent) / rate; val = __raw_readl(S3C_CLK_DIV0); - val &= armclk_mask; + val &= ~armclk_mask; val |= (div - 1); __raw_writel(val, S3C_CLK_DIV0); -- GitLab From 0e014e92ba93d905bcb39881dce2d38807b90c34 Mon Sep 17 00:00:00 2001 From: Peter Korsgaard Date: Fri, 17 Jul 2009 22:33:37 +0200 Subject: [PATCH 0498/1342] i2c-s3c2410: s3c24xx_i2c_init: don't clobber IICLC value s3c24xx_i2c_init() was overwriting the IICLC value set just above in s3c24xx_i2c_clockrate() with zero, effectively disabling the platform line control setting. Signed-off-by: Peter Korsgaard Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-s3c2410.c | 5 ----- 1 file changed, 5 deletions(-) diff --git a/drivers/i2c/busses/i2c-s3c2410.c b/drivers/i2c/busses/i2c-s3c2410.c index 8f42a4536cd..20bb0ceb027 100644 --- a/drivers/i2c/busses/i2c-s3c2410.c +++ b/drivers/i2c/busses/i2c-s3c2410.c @@ -763,11 +763,6 @@ static int s3c24xx_i2c_init(struct s3c24xx_i2c *i2c) dev_info(i2c->dev, "bus frequency set to %d KHz\n", freq); dev_dbg(i2c->dev, "S3C2410_IICCON=0x%02lx\n", iicon); - /* check for s3c2440 i2c controller */ - - if (s3c24xx_i2c_is2440(i2c)) - writel(0x0, i2c->regs + S3C2440_IICLC); - return 0; } -- GitLab From 783fd6fa4c144e3f6913e6fed89de10a6dd715a5 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Fri, 17 Jul 2009 15:24:00 +0200 Subject: [PATCH 0499/1342] i2c: strncpy does not null terminate string strlcpy() will always null terminate the string. Signed-off-by: Roel Kluin Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-omap.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index fdd83277c8a..f2b82ee39ad 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -879,7 +879,7 @@ omap_i2c_probe(struct platform_device *pdev) i2c_set_adapdata(adap, dev); adap->owner = THIS_MODULE; adap->class = I2C_CLASS_HWMON; - strncpy(adap->name, "OMAP I2C adapter", sizeof(adap->name)); + strlcpy(adap->name, "OMAP I2C adapter", sizeof(adap->name)); adap->algo = &omap_i2c_algo; adap->dev.parent = &pdev->dev; -- GitLab From ccb3bc16b4891a82649d4bccbeefe60b1d9a62e2 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Wed, 22 Jul 2009 23:58:39 +0900 Subject: [PATCH 0500/1342] i2c-sh_mobile: change module_init() to subsys_initcall() Convert the i2c-sh_mobile i2c bus driver to use subsys_initcall() instead of module_init(). This change makes the driver register a bit earlier which together with earlier platform data moves the time for probe(). The earlier probe() makes it possible to use i2c_get_adapter() and i2c_transfer() from device_initcall(). The same strategy is used by other i2c bus drivers such as i2c-pxa.c and i2c-s3c2410.c. Signed-off-by: Magnus Damm [ben-linux@fluff.org: minor subject updaye] Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-sh_mobile.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/i2c/busses/i2c-sh_mobile.c b/drivers/i2c/busses/i2c-sh_mobile.c index 4f3d99cd169..820487d0d5c 100644 --- a/drivers/i2c/busses/i2c-sh_mobile.c +++ b/drivers/i2c/busses/i2c-sh_mobile.c @@ -637,7 +637,7 @@ static void __exit sh_mobile_i2c_adap_exit(void) platform_driver_unregister(&sh_mobile_i2c_driver); } -module_init(sh_mobile_i2c_adap_init); +subsys_initcall(sh_mobile_i2c_adap_init); module_exit(sh_mobile_i2c_adap_exit); MODULE_DESCRIPTION("SuperH Mobile I2C Bus Controller driver"); -- GitLab From bfb6b6588af5ff762222cee79152d2be738ccc06 Mon Sep 17 00:00:00 2001 From: "Sonasath, Moiz" Date: Tue, 21 Jul 2009 10:14:06 -0500 Subject: [PATCH 0501/1342] i2c-omap: Bug in reading the RXSTAT/TXSTAT values from the I2C_BUFFSTAT register Fix bug in reading the I2C_BUFFSTAT register for getting byte count on RX/TX interrupt. On Interrupt: I2C_STAT[RDR], read 'RXSTAT' from I2C_BUFFSTAT[8-13] On Interrupt: I2C_STAT[XDR] read 'TXSTAT' from I2C_BUFFSTAT[0-5] Signed-off-by: Jagadeesh Pakaravoor Signed-off-by: Moiz Sonasath Signed-off-by: Vikram pandita [ben-linux@fluff.org: fixed mail format and added i2c-omap to subject] Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-omap.c | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-) diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index f2b82ee39ad..a6966578851 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -692,9 +692,10 @@ omap_i2c_isr(int this_irq, void *dev_id) if (dev->fifo_size) { if (stat & OMAP_I2C_STAT_RRDY) num_bytes = dev->fifo_size; - else - num_bytes = omap_i2c_read_reg(dev, - OMAP_I2C_BUFSTAT_REG); + else /* read RXSTAT on RDR interrupt */ + num_bytes = (omap_i2c_read_reg(dev, + OMAP_I2C_BUFSTAT_REG) + >> 8) & 0x3F; } while (num_bytes) { num_bytes--; @@ -731,9 +732,10 @@ omap_i2c_isr(int this_irq, void *dev_id) if (dev->fifo_size) { if (stat & OMAP_I2C_STAT_XRDY) num_bytes = dev->fifo_size; - else + else /* read TXSTAT on XDR interrupt */ num_bytes = omap_i2c_read_reg(dev, - OMAP_I2C_BUFSTAT_REG); + OMAP_I2C_BUFSTAT_REG) + & 0x3F; } while (num_bytes) { num_bytes--; -- GitLab From 04c688dd7a65935568b44629bfaa122eddf76e94 Mon Sep 17 00:00:00 2001 From: "Sonasath, Moiz" Date: Tue, 21 Jul 2009 10:14:40 -0500 Subject: [PATCH 0502/1342] i2c-omap: In case of a NACK|ARDY|AL return from the ISR In case of a NACK or ARDY or AL interrupt, complete the request. There is no need to service the RRDY/RDR or XRDY/XDR interrupts. Refer TRM SWPU114: Figure 18-31.I2C Master Transmitter Mode, Interrupt Method, in F/S and HS Modes http://focus.ti.com/pdfs/wtbu/SWPU114T_PrelimFinalEPDF_06_25_2009.pdf Signed-off-by: Moiz Sonasath Signed-off-by: Vikram pandita [ben-linux@fluff.org: fixed mail format and added i2c-omap to subject] Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-omap.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index a6966578851..5c508ccf438 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -685,8 +685,10 @@ omap_i2c_isr(int this_irq, void *dev_id) err |= OMAP_I2C_STAT_AL; } if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK | - OMAP_I2C_STAT_AL)) + OMAP_I2C_STAT_AL)) { omap_i2c_complete_cmd(dev, err); + return IRQ_HANDLED; + } if (stat & (OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR)) { u8 num_bytes = 1; if (dev->fifo_size) { -- GitLab From cd086d3aa6f7f7bf4d4e1f9fa09af0f0b6bb99ec Mon Sep 17 00:00:00 2001 From: "Sonasath, Moiz" Date: Tue, 21 Jul 2009 10:15:12 -0500 Subject: [PATCH 0503/1342] i2c-omap: OMAP3430 Silicon Errata 1.153 When an XRDY/XDR is hit, wait for XUDF before writing data to DATA_REG. Otherwise some data bytes can be lost while transferring them from the memory to the I2C interface. Do a Busy-wait for XUDF, before writing data to DATA_REG. While waiting if there is NACK | AL, set the appropriate error flags, ack the pending interrupts and return from the ISR. Signed-off-by: Moiz Sonasath Signed-off-by: Vikram pandita [ben-linux@fluff.org: fixed mail format and added i2c-omap to subject] Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-omap.c | 24 +++++++++++++++++++++++- 1 file changed, 23 insertions(+), 1 deletion(-) diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index 5c508ccf438..d258b02aef4 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -672,9 +672,10 @@ omap_i2c_isr(int this_irq, void *dev_id) break; } + err = 0; +complete: omap_i2c_write_reg(dev, OMAP_I2C_STAT_REG, stat); - err = 0; if (stat & OMAP_I2C_STAT_NACK) { err |= OMAP_I2C_STAT_NACK; omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, @@ -764,6 +765,27 @@ omap_i2c_isr(int this_irq, void *dev_id) "data to send\n"); break; } + + /* + * OMAP3430 Errata 1.153: When an XRDY/XDR + * is hit, wait for XUDF before writing data + * to DATA_REG. Otherwise some data bytes can + * be lost while transferring them from the + * memory to the I2C interface. + */ + + if (cpu_is_omap34xx()) { + while (!(stat & OMAP_I2C_STAT_XUDF)) { + if (stat & (OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) { + omap_i2c_ack_stat(dev, stat & (OMAP_I2C_STAT_XRDY | OMAP_I2C_STAT_XDR)); + err |= OMAP_I2C_STAT_XUDF; + goto complete; + } + cpu_relax(); + stat = omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG); + } + } + omap_i2c_write_reg(dev, OMAP_I2C_DATA_REG, w); } omap_i2c_ack_stat(dev, -- GitLab From 51fbb4bab6c8710eb897ab3fb06efbbc921f3a8d Mon Sep 17 00:00:00 2001 From: Matthew Wilcox Date: Wed, 29 Jul 2009 15:02:03 -0700 Subject: [PATCH 0504/1342] markup_oops: fix it with 32-bit userspace on a 64-bit kernel A 32-bit perl can't handle 64-bit addresses without using the BigInt package. Signed-off-by: Matthew Wilcox Acked-by: Arjan van de Ven Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- scripts/markup_oops.pl | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/scripts/markup_oops.pl b/scripts/markup_oops.pl index 528492bcba5..89774011965 100644 --- a/scripts/markup_oops.pl +++ b/scripts/markup_oops.pl @@ -1,6 +1,7 @@ #!/usr/bin/perl use File::Basename; +use Math::BigInt; # Copyright 2008, Intel Corporation # @@ -172,8 +173,8 @@ while () { parse_x86_regs($line); } -my $decodestart = hex($target) - hex($func_offset); -my $decodestop = hex($target) + 8192; +my $decodestart = Math::BigInt->from_hex("0x$target") - Math::BigInt->from_hex("0x$func_offset"); +my $decodestop = Math::BigInt->from_hex("0x$target") + 8192; if ($target eq "0") { print "No oops found!\n"; print "Usage: \n"; -- GitLab From e084b2d95e48b31aa45f9c49ffc6cdae8bdb21d4 Mon Sep 17 00:00:00 2001 From: Mel Gorman Date: Wed, 29 Jul 2009 15:02:04 -0700 Subject: [PATCH 0505/1342] page-allocator: preserve PFN ordering when __GFP_COLD is set Fix a post-2.6.24 performace regression caused by 3dfa5721f12c3d5a441448086bee156887daa961 ("page-allocator: preserve PFN ordering when __GFP_COLD is set"). Narayanan reports "The regression is around 15%. There is no disk controller as our setup is based on Samsung OneNAND used as a memory mapped device on a OMAP2430 based board." The page allocator tries to preserve contiguous PFN ordering when returning pages such that repeated callers to the allocator have a strong chance of getting physically contiguous pages, particularly when external fragmentation is low. However, of the bulk of the allocations have __GFP_COLD set as they are due to aio_read() for example, then the PFNs are in reverse PFN order. This can cause performance degration when used with IO controllers that could have merged the requests. This patch attempts to preserve the contiguous ordering of PFNs for users of __GFP_COLD. Signed-off-by: Mel Gorman Reported-by: Narayananu Gopalakrishnan Tested-by: Narayanan Gopalakrishnan Cc: KAMEZAWA Hiroyuki Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- mm/page_alloc.c | 13 +++++++++---- 1 file changed, 9 insertions(+), 4 deletions(-) diff --git a/mm/page_alloc.c b/mm/page_alloc.c index caa92689aac..ae28c22a7fd 100644 --- a/mm/page_alloc.c +++ b/mm/page_alloc.c @@ -882,7 +882,7 @@ retry_reserve: */ static int rmqueue_bulk(struct zone *zone, unsigned int order, unsigned long count, struct list_head *list, - int migratetype) + int migratetype, int cold) { int i; @@ -901,7 +901,10 @@ static int rmqueue_bulk(struct zone *zone, unsigned int order, * merge IO requests if the physical pages are ordered * properly. */ - list_add(&page->lru, list); + if (likely(cold == 0)) + list_add(&page->lru, list); + else + list_add_tail(&page->lru, list); set_page_private(page, migratetype); list = &page->lru; } @@ -1119,7 +1122,8 @@ again: local_irq_save(flags); if (!pcp->count) { pcp->count = rmqueue_bulk(zone, 0, - pcp->batch, &pcp->list, migratetype); + pcp->batch, &pcp->list, + migratetype, cold); if (unlikely(!pcp->count)) goto failed; } @@ -1138,7 +1142,8 @@ again: /* Allocate more to the pcp list if necessary */ if (unlikely(&page->lru == &pcp->list)) { pcp->count += rmqueue_bulk(zone, 0, - pcp->batch, &pcp->list, migratetype); + pcp->batch, &pcp->list, + migratetype, cold); page = list_entry(pcp->list.next, struct page, lru); } -- GitLab From 6583bb64fc370842b32a87c67750c26f6d559af0 Mon Sep 17 00:00:00 2001 From: David Rientjes Date: Wed, 29 Jul 2009 15:02:06 -0700 Subject: [PATCH 0506/1342] mm: avoid endless looping for oom killed tasks If a task is oom killed and still cannot find memory when trying with no watermarks, it's better to fail the allocation attempt than to loop endlessly. Direct reclaim has already failed and the oom killer will be a no-op since current has yet to die, so there is no other alternative for allocations that are not __GFP_NOFAIL. Acked-by: Mel Gorman Signed-off-by: David Rientjes Acked-by: Hugh Dickins Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- mm/page_alloc.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/mm/page_alloc.c b/mm/page_alloc.c index ae28c22a7fd..2dbb2fc6883 100644 --- a/mm/page_alloc.c +++ b/mm/page_alloc.c @@ -1794,6 +1794,10 @@ rebalance: if (p->flags & PF_MEMALLOC) goto nopage; + /* Avoid allocations with no watermarks from looping endlessly */ + if (test_thread_flag(TIF_MEMDIE) && !(gfp_mask & __GFP_NOFAIL)) + goto nopage; + /* Try direct reclaim and then allocating */ page = __alloc_pages_direct_reclaim(gfp_mask, order, zonelist, high_zoneidx, -- GitLab From 933b787b57ca8bdc0fc8fb2cbf67b5e6d21beb84 Mon Sep 17 00:00:00 2001 From: Rik van Riel Date: Wed, 29 Jul 2009 15:02:07 -0700 Subject: [PATCH 0507/1342] mm: copy over oom_adj value at fork time Fix a post-2.6.31 regression which was introduced by 2ff05b2b4eac2e63d345fc731ea151a060247f53 ("oom: move oom_adj value from task_struct to mm_struct"). After moving the oom_adj value from the task struct to the mm_struct, the oom_adj value was no longer properly inherited by child processes. Copying over the oom_adj value at fork time fixes that bug. [kosaki.motohiro@jp.fujitsu.com: test for current->mm before dereferencing it] Signed-off-by: Rik van Riel Reported-by: Paul Menage Cc: KOSAKI Motohiro Acked-by: David Rientjes Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- kernel/fork.c | 1 + 1 file changed, 1 insertion(+) diff --git a/kernel/fork.c b/kernel/fork.c index 9b42695f0d1..29b532e718f 100644 --- a/kernel/fork.c +++ b/kernel/fork.c @@ -426,6 +426,7 @@ static struct mm_struct * mm_init(struct mm_struct * mm, struct task_struct *p) init_rwsem(&mm->mmap_sem); INIT_LIST_HEAD(&mm->mmlist); mm->flags = (current->mm) ? current->mm->flags : default_dump_filter; + mm->oom_adj = (current->mm) ? current->mm->oom_adj : 0; mm->core_state = NULL; mm->nr_ptes = 0; set_mm_counter(mm, file_rss, 0); -- GitLab From 11c7da4b0ca76a57f51c996c883c480e203cf5a9 Mon Sep 17 00:00:00 2001 From: Hidetoshi Seto Date: Wed, 29 Jul 2009 15:02:08 -0700 Subject: [PATCH 0508/1342] kexec: fix omitting offset in extended crashkernel syntax Setting "crashkernel=512M-2G:64M,2G-:128M" does not work but it turns to work if it has a trailing-whitespace, like "crashkernel=512M-2G:64M,2G-:128M ". It was because of a bug in the parser, running over the cmdline. This patch adds a check of the termination. Reported-by: Jin Dongming Signed-off-by: Hidetoshi Seto Tested-by: Jin Dongming Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- kernel/kexec.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/kexec.c b/kernel/kexec.c index ae1c35201cc..f336e2107f9 100644 --- a/kernel/kexec.c +++ b/kernel/kexec.c @@ -1228,7 +1228,7 @@ static int __init parse_crashkernel_mem(char *cmdline, } while (*cur++ == ','); if (*crash_size > 0) { - while (*cur != ' ' && *cur != '@') + while (*cur && *cur != ' ' && *cur != '@') cur++; if (*cur == '@') { cur++; -- GitLab From 3d768213a6c34a27fac1804143da8cf18b8b175f Mon Sep 17 00:00:00 2001 From: Lu Zhihe Date: Wed, 29 Jul 2009 15:02:09 -0700 Subject: [PATCH 0509/1342] edac: x38 fix mchbar high register addr Intel X38 MCHBAR is a 64bits register, base from 0x48, so its higher base is 0x4C. Signed-off-by: Lu Zhihe Signed-off-by: Doug Thompson Cc: [2.6.30.x] Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/edac/x38_edac.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/edac/x38_edac.c b/drivers/edac/x38_edac.c index 2406c2ce284..d4ec6059317 100644 --- a/drivers/edac/x38_edac.c +++ b/drivers/edac/x38_edac.c @@ -30,7 +30,7 @@ /* Intel X38 register addresses - device 0 function 0 - DRAM Controller */ #define X38_MCHBAR_LOW 0x48 /* MCH Memory Mapped Register BAR */ -#define X38_MCHBAR_HIGH 0x4b +#define X38_MCHBAR_HIGH 0x4c #define X38_MCHBAR_MASK 0xfffffc000ULL /* bits 35:14 */ #define X38_MMR_WINDOW_SIZE 16384 -- GitLab From c42b110caeb128819104d057acdaa1ae564b7c8d Mon Sep 17 00:00:00 2001 From: Pawel Osciak Date: Wed, 29 Jul 2009 15:02:10 -0700 Subject: [PATCH 0510/1342] s3c-fb: fix off-by-one bug in loop indexes Fixed off-by-one bug in loop indexes - some elements beyond windows' array were accessed, which might result in memory access violations when removing/suspending the device. Signed-off-by: Pawel Osciak Reviewed-by: Kyungmin Park Signed-off-by: Marek Szyprowski Cc: Krzysztof Helt Cc: Ben Dooks Cc: Russell King Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/s3c-fb.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/video/s3c-fb.c b/drivers/video/s3c-fb.c index bb63c07e13d..5a72083dc67 100644 --- a/drivers/video/s3c-fb.c +++ b/drivers/video/s3c-fb.c @@ -964,7 +964,7 @@ static int __devexit s3c_fb_remove(struct platform_device *pdev) struct s3c_fb *sfb = platform_get_drvdata(pdev); int win; - for (win = 0; win <= S3C_FB_MAX_WIN; win++) + for (win = 0; win < S3C_FB_MAX_WIN; win++) if (sfb->windows[win]) s3c_fb_release_win(sfb, sfb->windows[win]); @@ -988,7 +988,7 @@ static int s3c_fb_suspend(struct platform_device *pdev, pm_message_t state) struct s3c_fb_win *win; int win_no; - for (win_no = S3C_FB_MAX_WIN; win_no >= 0; win_no--) { + for (win_no = S3C_FB_MAX_WIN - 1; win_no >= 0; win_no--) { win = sfb->windows[win_no]; if (!win) continue; -- GitLab From ddb22195cb3dc5175ba3aac5e957d0e34cd2ee73 Mon Sep 17 00:00:00 2001 From: Jouni Hogander Date: Wed, 29 Jul 2009 15:02:11 -0700 Subject: [PATCH 0511/1342] spi: omap2_mcspi supports wake events Currently mcspi wake-ups are not enabled. This might cause cases where OMAP is not waking up on mcspi events. Signed-off-by: Jouni Hogander Signed-off-by: Tony Lindgren Signed-off-by: David Brownell Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/spi/omap2_mcspi.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-) diff --git a/drivers/spi/omap2_mcspi.c b/drivers/spi/omap2_mcspi.c index eee4b6e0af2..2b64091b0f1 100644 --- a/drivers/spi/omap2_mcspi.c +++ b/drivers/spi/omap2_mcspi.c @@ -59,6 +59,8 @@ /* per-register bitmasks: */ +#define OMAP2_MCSPI_SYSCONFIG_SMARTIDLE (2 << 3) +#define OMAP2_MCSPI_SYSCONFIG_ENAWAKEUP (1 << 2) #define OMAP2_MCSPI_SYSCONFIG_AUTOIDLE (1 << 0) #define OMAP2_MCSPI_SYSCONFIG_SOFTRESET (1 << 1) @@ -90,6 +92,7 @@ #define OMAP2_MCSPI_CHCTRL_EN (1 << 0) +#define OMAP2_MCSPI_WAKEUPENABLE_WKEN (1 << 0) /* We have 2 DMA channels per CS, one for RX and one for TX */ struct omap2_mcspi_dma { @@ -873,8 +876,12 @@ static int __init omap2_mcspi_reset(struct omap2_mcspi *mcspi) } while (!(tmp & OMAP2_MCSPI_SYSSTATUS_RESETDONE)); mcspi_write_reg(master, OMAP2_MCSPI_SYSCONFIG, - /* (3 << 8) | (2 << 3) | */ - OMAP2_MCSPI_SYSCONFIG_AUTOIDLE); + OMAP2_MCSPI_SYSCONFIG_AUTOIDLE | + OMAP2_MCSPI_SYSCONFIG_ENAWAKEUP | + OMAP2_MCSPI_SYSCONFIG_SMARTIDLE); + + mcspi_write_reg(master, OMAP2_MCSPI_WAKEUPENABLE, + OMAP2_MCSPI_WAKEUPENABLE_WKEN); omap2_mcspi_set_master_mode(master); -- GitLab From 57c5c28dbc835c67a9c23912bab56b7f165e7715 Mon Sep 17 00:00:00 2001 From: Eero Nurkkala Date: Wed, 29 Jul 2009 15:02:12 -0700 Subject: [PATCH 0512/1342] spi: omap2_mcspi rxdma bugfix When data is read through DMA, the last element must be read separately through the RX register. It cannot be transferred by the DMA. For further details see e.g. OMAP35x TRM (table 19-16). Without the fix the driver causes extra clocks to be clocked to the bus after DMA RX operations. This can cause interesting behaviour with some devices. Signed-off-by: Juuso Oikarinen Signed-off-by: Eero Nurkkala [aaro.koskinen@nokia.com: Simplified the patch while keeping the idea.] Signed-off-by: Aaro Koskinen Signed-off-by: David Brownell Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/spi/omap2_mcspi.c | 21 ++++++++++++++++++++- 1 file changed, 20 insertions(+), 1 deletion(-) diff --git a/drivers/spi/omap2_mcspi.c b/drivers/spi/omap2_mcspi.c index 2b64091b0f1..9b80ad36dbb 100644 --- a/drivers/spi/omap2_mcspi.c +++ b/drivers/spi/omap2_mcspi.c @@ -272,7 +272,7 @@ omap2_mcspi_txrx_dma(struct spi_device *spi, struct spi_transfer *xfer) if (rx != NULL) { omap_set_dma_transfer_params(mcspi_dma->dma_rx_channel, - data_type, element_count, 1, + data_type, element_count - 1, 1, OMAP_DMA_SYNC_ELEMENT, mcspi_dma->dma_rx_sync_dev, 1); @@ -303,6 +303,25 @@ omap2_mcspi_txrx_dma(struct spi_device *spi, struct spi_transfer *xfer) if (rx != NULL) { wait_for_completion(&mcspi_dma->dma_rx_completion); dma_unmap_single(NULL, xfer->rx_dma, count, DMA_FROM_DEVICE); + omap2_mcspi_set_enable(spi, 0); + if (likely(mcspi_read_cs_reg(spi, OMAP2_MCSPI_CHSTAT0) + & OMAP2_MCSPI_CHSTAT_RXS)) { + u32 w; + + w = mcspi_read_cs_reg(spi, OMAP2_MCSPI_RX0); + if (word_len <= 8) + ((u8 *)xfer->rx_buf)[element_count - 1] = w; + else if (word_len <= 16) + ((u16 *)xfer->rx_buf)[element_count - 1] = w; + else /* word_len <= 32 */ + ((u32 *)xfer->rx_buf)[element_count - 1] = w; + } else { + dev_err(&spi->dev, "DMA RX last word empty"); + count -= (word_len <= 8) ? 1 : + (word_len <= 16) ? 2 : + /* word_len <= 32 */ 4; + } + omap2_mcspi_set_enable(spi, 1); } return count; } -- GitLab From 659098141d02eb8e3545be8969d262e02d2f3f98 Mon Sep 17 00:00:00 2001 From: Thadeu Lima de Souza Cascardo Date: Wed, 29 Jul 2009 15:02:13 -0700 Subject: [PATCH 0513/1342] rtc: mark if rtc-cmos drivers were successfully registered rtc-cmos has two drivers, one PNP and one platform. When PNP has not succeeded probing, platform is registered. However, it tries to unregister both drivers unconditionally, instead of only unregistering those that were successfully registered. This causes runtime warnings to be emitted from the driver core code. Fix this with a boolean variable for each driver indicating whether registering was successful. Signed-off-by: Thadeu Lima de Souza Cascardo Cc: David Brownell Cc: Bjorn Helgaas Cc: Alessandro Zummo Cc: Ingo Molnar Cc: David Brownell Cc: Kay Sievers Cc: Greg KH Cc: Ozan Caglayan Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/rtc/rtc-cmos.c | 23 ++++++++++++++++++----- 1 file changed, 18 insertions(+), 5 deletions(-) diff --git a/drivers/rtc/rtc-cmos.c b/drivers/rtc/rtc-cmos.c index 23e10b6263d..f7a4701bf86 100644 --- a/drivers/rtc/rtc-cmos.c +++ b/drivers/rtc/rtc-cmos.c @@ -1174,23 +1174,34 @@ static struct platform_driver cmos_platform_driver = { } }; +#ifdef CONFIG_PNP +static bool pnp_driver_registered; +#endif +static bool platform_driver_registered; + static int __init cmos_init(void) { int retval = 0; #ifdef CONFIG_PNP - pnp_register_driver(&cmos_pnp_driver); + retval = pnp_register_driver(&cmos_pnp_driver); + if (retval == 0) + pnp_driver_registered = true; #endif - if (!cmos_rtc.dev) + if (!cmos_rtc.dev) { retval = platform_driver_probe(&cmos_platform_driver, cmos_platform_probe); + if (retval == 0) + platform_driver_registered = true; + } if (retval == 0) return 0; #ifdef CONFIG_PNP - pnp_unregister_driver(&cmos_pnp_driver); + if (pnp_driver_registered) + pnp_unregister_driver(&cmos_pnp_driver); #endif return retval; } @@ -1199,9 +1210,11 @@ module_init(cmos_init); static void __exit cmos_exit(void) { #ifdef CONFIG_PNP - pnp_unregister_driver(&cmos_pnp_driver); + if (pnp_driver_registered) + pnp_unregister_driver(&cmos_pnp_driver); #endif - platform_driver_unregister(&cmos_platform_driver); + if (platform_driver_registered) + platform_driver_unregister(&cmos_platform_driver); } module_exit(cmos_exit); -- GitLab From e4c6f8bed01f9f9a5c607bd689bf67e7b8a36bd8 Mon Sep 17 00:00:00 2001 From: Eric Sandeen Date: Wed, 29 Jul 2009 15:02:16 -0700 Subject: [PATCH 0514/1342] hugetlbfs: fix i_blocks accounting As reported in Red Hat bz #509671, i_blocks for files on hugetlbfs get accounting wrong when doing something like: $ > foo $ date > foo date: write error: Invalid argument $ /usr/bin/stat foo File: `foo' Size: 0 Blocks: 18446744073709547520 IO Block: 2097152 regular ... This is because hugetlb_unreserve_pages() is unconditionally removing blocks_per_huge_page(h) on each call rather than using the freed amount. If there were 0 blocks, it goes negative, resulting in the above. This is a regression from commit a5516438959d90b071ff0a484ce4f3f523dc3152 ("hugetlb: modular state for hugetlb page size") which did: - inode->i_blocks -= BLOCKS_PER_HUGEPAGE * freed; + inode->i_blocks -= blocks_per_huge_page(h); so just put back the freed multiplier, and it's all happy again. Signed-off-by: Eric Sandeen Acked-by: Andi Kleen Cc: William Lee Irwin III Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- mm/hugetlb.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/mm/hugetlb.c b/mm/hugetlb.c index d0351e31f47..cafdcee154e 100644 --- a/mm/hugetlb.c +++ b/mm/hugetlb.c @@ -2370,7 +2370,7 @@ void hugetlb_unreserve_pages(struct inode *inode, long offset, long freed) long chg = region_truncate(&inode->i_mapping->private_list, offset); spin_lock(&inode->i_lock); - inode->i_blocks -= blocks_per_huge_page(h); + inode->i_blocks -= (blocks_per_huge_page(h) * freed); spin_unlock(&inode->i_lock); hugetlb_put_quota(inode->i_mapping, (chg - freed)); -- GitLab From 3fc7b4b220c7e830a5b3ce0ea5f85a635e0c50f0 Mon Sep 17 00:00:00 2001 From: Roland Dreier Date: Wed, 29 Jul 2009 15:04:02 -0700 Subject: [PATCH 0515/1342] lib: export generic atomic64_t functions The generic atomic64_t implementation in lib/ did not export the functions it defined, which means that modules that use atomic64_t would not link on platforms (such as 32-bit powerpc). For example, trying to build a kernel with CONFIG_NET_RDS on such a platform would fail with: ERROR: "atomic64_read" [net/rds/rds.ko] undefined! ERROR: "atomic64_set" [net/rds/rds.ko] undefined! Fix this by exporting the atomic64_t functions to modules. (I export the entire API even if it's not all currently used by in-tree modules to avoid having to continue fixing this in dribs and drabs) Signed-off-by: Roland Dreier Acked-by: Paul Mackerras Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- lib/atomic64.c | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/lib/atomic64.c b/lib/atomic64.c index c5e72556241..8bee16ec752 100644 --- a/lib/atomic64.c +++ b/lib/atomic64.c @@ -13,6 +13,7 @@ #include #include #include +#include #include /* @@ -52,6 +53,7 @@ long long atomic64_read(const atomic64_t *v) spin_unlock_irqrestore(lock, flags); return val; } +EXPORT_SYMBOL(atomic64_read); void atomic64_set(atomic64_t *v, long long i) { @@ -62,6 +64,7 @@ void atomic64_set(atomic64_t *v, long long i) v->counter = i; spin_unlock_irqrestore(lock, flags); } +EXPORT_SYMBOL(atomic64_set); void atomic64_add(long long a, atomic64_t *v) { @@ -72,6 +75,7 @@ void atomic64_add(long long a, atomic64_t *v) v->counter += a; spin_unlock_irqrestore(lock, flags); } +EXPORT_SYMBOL(atomic64_add); long long atomic64_add_return(long long a, atomic64_t *v) { @@ -84,6 +88,7 @@ long long atomic64_add_return(long long a, atomic64_t *v) spin_unlock_irqrestore(lock, flags); return val; } +EXPORT_SYMBOL(atomic64_add_return); void atomic64_sub(long long a, atomic64_t *v) { @@ -94,6 +99,7 @@ void atomic64_sub(long long a, atomic64_t *v) v->counter -= a; spin_unlock_irqrestore(lock, flags); } +EXPORT_SYMBOL(atomic64_sub); long long atomic64_sub_return(long long a, atomic64_t *v) { @@ -106,6 +112,7 @@ long long atomic64_sub_return(long long a, atomic64_t *v) spin_unlock_irqrestore(lock, flags); return val; } +EXPORT_SYMBOL(atomic64_sub_return); long long atomic64_dec_if_positive(atomic64_t *v) { @@ -120,6 +127,7 @@ long long atomic64_dec_if_positive(atomic64_t *v) spin_unlock_irqrestore(lock, flags); return val; } +EXPORT_SYMBOL(atomic64_dec_if_positive); long long atomic64_cmpxchg(atomic64_t *v, long long o, long long n) { @@ -134,6 +142,7 @@ long long atomic64_cmpxchg(atomic64_t *v, long long o, long long n) spin_unlock_irqrestore(lock, flags); return val; } +EXPORT_SYMBOL(atomic64_cmpxchg); long long atomic64_xchg(atomic64_t *v, long long new) { @@ -147,6 +156,7 @@ long long atomic64_xchg(atomic64_t *v, long long new) spin_unlock_irqrestore(lock, flags); return val; } +EXPORT_SYMBOL(atomic64_xchg); int atomic64_add_unless(atomic64_t *v, long long a, long long u) { @@ -162,6 +172,7 @@ int atomic64_add_unless(atomic64_t *v, long long a, long long u) spin_unlock_irqrestore(lock, flags); return ret; } +EXPORT_SYMBOL(atomic64_add_unless); static int init_atomic64_lock(void) { -- GitLab From b317c833211b7fbf902163de766f09554090e0bf Mon Sep 17 00:00:00 2001 From: Kristoffer Ericson Date: Wed, 29 Jul 2009 15:04:03 -0700 Subject: [PATCH 0516/1342] drivers/video/backlight/jornada720_bl.c: fix build Signed-off-by: Kristoffer Ericson Cc: Richard Purdie Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/backlight/jornada720_bl.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/video/backlight/jornada720_bl.c b/drivers/video/backlight/jornada720_bl.c index c3ebb6b41ce..7aed2565c1b 100644 --- a/drivers/video/backlight/jornada720_bl.c +++ b/drivers/video/backlight/jornada720_bl.c @@ -72,7 +72,7 @@ static int jornada_bl_update_status(struct backlight_device *bd) if (jornada_ssp_byte(SETBRIGHTNESS) != TXDUMMY) { printk(KERN_INFO "bl : failed to set brightness\n"); ret = -ETIMEDOUT; - goto out + goto out; } /* at this point we expect that the mcu has accepted -- GitLab From 096b7fe012d66ed55e98bc8022405ede0cc80e96 Mon Sep 17 00:00:00 2001 From: Li Zefan Date: Wed, 29 Jul 2009 15:04:04 -0700 Subject: [PATCH 0517/1342] cgroups: fix pid namespace bug The bug was introduced by commit cc31edceee04a7b87f2be48f9489ebb72d264844 ("cgroups: convert tasks file to use a seq_file with shared pid array"). We cache a pid array for all threads that are opening the same "tasks" file, but the pids in the array are always from the namespace of the last process that opened the file, so all other threads will read pids from that namespace instead of their own namespaces. To fix it, we maintain a list of pid arrays, which is keyed by pid_ns. The list will be of length 1 at most time. Reported-by: Paul Menage Idea-by: Paul Menage Signed-off-by: Li Zefan Reviewed-by: Serge Hallyn Cc: Balbir Singh Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- include/linux/cgroup.h | 11 ++--- kernel/cgroup.c | 96 +++++++++++++++++++++++++++++++----------- 2 files changed, 76 insertions(+), 31 deletions(-) diff --git a/include/linux/cgroup.h b/include/linux/cgroup.h index 665fa70e409..20411d2876f 100644 --- a/include/linux/cgroup.h +++ b/include/linux/cgroup.h @@ -179,14 +179,11 @@ struct cgroup { */ struct list_head release_list; - /* pids_mutex protects the fields below */ + /* pids_mutex protects pids_list and cached pid arrays. */ struct rw_semaphore pids_mutex; - /* Array of process ids in the cgroup */ - pid_t *tasks_pids; - /* How many files are using the current tasks_pids array */ - int pids_use_count; - /* Length of the current tasks_pids array */ - int pids_length; + + /* Linked list of struct cgroup_pids */ + struct list_head pids_list; /* For RCU-protected deletion */ struct rcu_head rcu_head; diff --git a/kernel/cgroup.c b/kernel/cgroup.c index 3737a682cdf..250dac05680 100644 --- a/kernel/cgroup.c +++ b/kernel/cgroup.c @@ -47,6 +47,7 @@ #include #include #include +#include #include @@ -960,6 +961,7 @@ static void init_cgroup_housekeeping(struct cgroup *cgrp) INIT_LIST_HEAD(&cgrp->children); INIT_LIST_HEAD(&cgrp->css_sets); INIT_LIST_HEAD(&cgrp->release_list); + INIT_LIST_HEAD(&cgrp->pids_list); init_rwsem(&cgrp->pids_mutex); } static void init_cgroup_root(struct cgroupfs_root *root) @@ -2201,12 +2203,30 @@ err: return ret; } +/* + * Cache pids for all threads in the same pid namespace that are + * opening the same "tasks" file. + */ +struct cgroup_pids { + /* The node in cgrp->pids_list */ + struct list_head list; + /* The cgroup those pids belong to */ + struct cgroup *cgrp; + /* The namepsace those pids belong to */ + struct pid_namespace *ns; + /* Array of process ids in the cgroup */ + pid_t *tasks_pids; + /* How many files are using the this tasks_pids array */ + int use_count; + /* Length of the current tasks_pids array */ + int length; +}; + static int cmppid(const void *a, const void *b) { return *(pid_t *)a - *(pid_t *)b; } - /* * seq_file methods for the "tasks" file. The seq_file position is the * next pid to display; the seq_file iterator is a pointer to the pid @@ -2221,45 +2241,47 @@ static void *cgroup_tasks_start(struct seq_file *s, loff_t *pos) * after a seek to the start). Use a binary-search to find the * next pid to display, if any */ - struct cgroup *cgrp = s->private; + struct cgroup_pids *cp = s->private; + struct cgroup *cgrp = cp->cgrp; int index = 0, pid = *pos; int *iter; down_read(&cgrp->pids_mutex); if (pid) { - int end = cgrp->pids_length; + int end = cp->length; while (index < end) { int mid = (index + end) / 2; - if (cgrp->tasks_pids[mid] == pid) { + if (cp->tasks_pids[mid] == pid) { index = mid; break; - } else if (cgrp->tasks_pids[mid] <= pid) + } else if (cp->tasks_pids[mid] <= pid) index = mid + 1; else end = mid; } } /* If we're off the end of the array, we're done */ - if (index >= cgrp->pids_length) + if (index >= cp->length) return NULL; /* Update the abstract position to be the actual pid that we found */ - iter = cgrp->tasks_pids + index; + iter = cp->tasks_pids + index; *pos = *iter; return iter; } static void cgroup_tasks_stop(struct seq_file *s, void *v) { - struct cgroup *cgrp = s->private; + struct cgroup_pids *cp = s->private; + struct cgroup *cgrp = cp->cgrp; up_read(&cgrp->pids_mutex); } static void *cgroup_tasks_next(struct seq_file *s, void *v, loff_t *pos) { - struct cgroup *cgrp = s->private; + struct cgroup_pids *cp = s->private; int *p = v; - int *end = cgrp->tasks_pids + cgrp->pids_length; + int *end = cp->tasks_pids + cp->length; /* * Advance to the next pid in the array. If this goes off the @@ -2286,26 +2308,33 @@ static struct seq_operations cgroup_tasks_seq_operations = { .show = cgroup_tasks_show, }; -static void release_cgroup_pid_array(struct cgroup *cgrp) +static void release_cgroup_pid_array(struct cgroup_pids *cp) { + struct cgroup *cgrp = cp->cgrp; + down_write(&cgrp->pids_mutex); - BUG_ON(!cgrp->pids_use_count); - if (!--cgrp->pids_use_count) { - kfree(cgrp->tasks_pids); - cgrp->tasks_pids = NULL; - cgrp->pids_length = 0; + BUG_ON(!cp->use_count); + if (!--cp->use_count) { + list_del(&cp->list); + put_pid_ns(cp->ns); + kfree(cp->tasks_pids); + kfree(cp); } up_write(&cgrp->pids_mutex); } static int cgroup_tasks_release(struct inode *inode, struct file *file) { - struct cgroup *cgrp = __d_cgrp(file->f_dentry->d_parent); + struct seq_file *seq; + struct cgroup_pids *cp; if (!(file->f_mode & FMODE_READ)) return 0; - release_cgroup_pid_array(cgrp); + seq = file->private_data; + cp = seq->private; + + release_cgroup_pid_array(cp); return seq_release(inode, file); } @@ -2324,6 +2353,8 @@ static struct file_operations cgroup_tasks_operations = { static int cgroup_tasks_open(struct inode *unused, struct file *file) { struct cgroup *cgrp = __d_cgrp(file->f_dentry->d_parent); + struct pid_namespace *ns = current->nsproxy->pid_ns; + struct cgroup_pids *cp; pid_t *pidarray; int npids; int retval; @@ -2350,20 +2381,37 @@ static int cgroup_tasks_open(struct inode *unused, struct file *file) * array if necessary */ down_write(&cgrp->pids_mutex); - kfree(cgrp->tasks_pids); - cgrp->tasks_pids = pidarray; - cgrp->pids_length = npids; - cgrp->pids_use_count++; + + list_for_each_entry(cp, &cgrp->pids_list, list) { + if (ns == cp->ns) + goto found; + } + + cp = kzalloc(sizeof(*cp), GFP_KERNEL); + if (!cp) { + up_write(&cgrp->pids_mutex); + kfree(pidarray); + return -ENOMEM; + } + cp->cgrp = cgrp; + cp->ns = ns; + get_pid_ns(ns); + list_add(&cp->list, &cgrp->pids_list); +found: + kfree(cp->tasks_pids); + cp->tasks_pids = pidarray; + cp->length = npids; + cp->use_count++; up_write(&cgrp->pids_mutex); file->f_op = &cgroup_tasks_operations; retval = seq_open(file, &cgroup_tasks_seq_operations); if (retval) { - release_cgroup_pid_array(cgrp); + release_cgroup_pid_array(cp); return retval; } - ((struct seq_file *)file->private_data)->private = cgrp; + ((struct seq_file *)file->private_data)->private = cp; return 0; } -- GitLab From f0d83679a8d471dc8b646919f70595d6fe8c9606 Mon Sep 17 00:00:00 2001 From: Sebastian Heutling Date: Wed, 29 Jul 2009 15:04:05 -0700 Subject: [PATCH 0518/1342] eeprom/at25: bugfix "not ready" timeout after write Under certain circumstances msleep(1) within the loop, which waits for the EEPROM to be finished, might take longer than the timeout. On the next loop the status register might now return to be ready and therefore the loop finishes. The following check now tests if a timeout occurred and if so returns an error although the device reported it was ready. This fix replaces testing the occurrence of the timeout by testing the "not ready" bit in the status register. Signed-off-by: Sebastian Heutling Signed-off-by: David Brownell Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/misc/eeprom/at25.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/misc/eeprom/at25.c b/drivers/misc/eeprom/at25.c index b34cb5f79ee..2e535a0ccd5 100644 --- a/drivers/misc/eeprom/at25.c +++ b/drivers/misc/eeprom/at25.c @@ -173,6 +173,7 @@ at25_ee_write(struct at25_data *at25, const char *buf, loff_t off, unsigned segment; unsigned offset = (unsigned) off; u8 *cp = bounce + 1; + int sr; *cp = AT25_WREN; status = spi_write(at25->spi, cp, 1); @@ -214,7 +215,6 @@ at25_ee_write(struct at25_data *at25, const char *buf, loff_t off, timeout = jiffies + msecs_to_jiffies(EE_TIMEOUT); retries = 0; do { - int sr; sr = spi_w8r8(at25->spi, AT25_RDSR); if (sr < 0 || (sr & AT25_SR_nRDY)) { @@ -228,7 +228,7 @@ at25_ee_write(struct at25_data *at25, const char *buf, loff_t off, break; } while (retries++ < 3 || time_before_eq(jiffies, timeout)); - if (time_after(jiffies, timeout)) { + if ((sr < 0) || (sr & AT25_SR_nRDY)) { dev_err(&at25->spi->dev, "write %d bytes offset %d, " "timeout after %u msecs\n", -- GitLab From 887032670d47366a8c8f25396ea7c14b7b2cc620 Mon Sep 17 00:00:00 2001 From: KAMEZAWA Hiroyuki Date: Wed, 29 Jul 2009 15:04:06 -0700 Subject: [PATCH 0519/1342] cgroup avoid permanent sleep at rmdir After commit ec64f51545fffbc4cb968f0cea56341a4b07e85a ("cgroup: fix frequent -EBUSY at rmdir"), cgroup's rmdir (especially against memcg) doesn't return -EBUSY by temporary ref counts. That commit expects all refs after pre_destroy() is temporary but...it wasn't. Then, rmdir can wait permanently. This patch tries to fix that and change followings. - set CGRP_WAIT_ON_RMDIR flag before pre_destroy(). - clear CGRP_WAIT_ON_RMDIR flag when the subsys finds racy case. if there are sleeping ones, wakes them up. - rmdir() sleeps only when CGRP_WAIT_ON_RMDIR flag is set. Tested-by: Daisuke Nishimura Reported-by: Daisuke Nishimura Reviewed-by: Paul Menage Acked-by: Balbir Sigh Signed-off-by: KAMEZAWA Hiroyuki Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- include/linux/cgroup.h | 17 +++++++++++++ kernel/cgroup.c | 55 +++++++++++++++++++++++++++++------------- mm/memcontrol.c | 23 +++++++++++++++--- 3 files changed, 75 insertions(+), 20 deletions(-) diff --git a/include/linux/cgroup.h b/include/linux/cgroup.h index 20411d2876f..90bba9e6228 100644 --- a/include/linux/cgroup.h +++ b/include/linux/cgroup.h @@ -362,6 +362,23 @@ int cgroup_task_count(const struct cgroup *cgrp); /* Return true if cgrp is a descendant of the task's cgroup */ int cgroup_is_descendant(const struct cgroup *cgrp, struct task_struct *task); +/* + * When the subsys has to access css and may add permanent refcnt to css, + * it should take care of racy conditions with rmdir(). Following set of + * functions, is for stop/restart rmdir if necessary. + * Because these will call css_get/put, "css" should be alive css. + * + * cgroup_exclude_rmdir(); + * ...do some jobs which may access arbitrary empty cgroup + * cgroup_release_and_wakeup_rmdir(); + * + * When someone removes a cgroup while cgroup_exclude_rmdir() holds it, + * it sleeps and cgroup_release_and_wakeup_rmdir() will wake him up. + */ + +void cgroup_exclude_rmdir(struct cgroup_subsys_state *css); +void cgroup_release_and_wakeup_rmdir(struct cgroup_subsys_state *css); + /* * Control Group subsystem type. * See Documentation/cgroups/cgroups.txt for details diff --git a/kernel/cgroup.c b/kernel/cgroup.c index 250dac05680..b6eadfe30e7 100644 --- a/kernel/cgroup.c +++ b/kernel/cgroup.c @@ -735,16 +735,28 @@ static void cgroup_d_remove_dir(struct dentry *dentry) * reference to css->refcnt. In general, this refcnt is expected to goes down * to zero, soon. * - * CGRP_WAIT_ON_RMDIR flag is modified under cgroup's inode->i_mutex; + * CGRP_WAIT_ON_RMDIR flag is set under cgroup's inode->i_mutex; */ DECLARE_WAIT_QUEUE_HEAD(cgroup_rmdir_waitq); -static void cgroup_wakeup_rmdir_waiters(const struct cgroup *cgrp) +static void cgroup_wakeup_rmdir_waiter(struct cgroup *cgrp) { - if (unlikely(test_bit(CGRP_WAIT_ON_RMDIR, &cgrp->flags))) + if (unlikely(test_and_clear_bit(CGRP_WAIT_ON_RMDIR, &cgrp->flags))) wake_up_all(&cgroup_rmdir_waitq); } +void cgroup_exclude_rmdir(struct cgroup_subsys_state *css) +{ + css_get(css); +} + +void cgroup_release_and_wakeup_rmdir(struct cgroup_subsys_state *css) +{ + cgroup_wakeup_rmdir_waiter(css->cgroup); + css_put(css); +} + + static int rebind_subsystems(struct cgroupfs_root *root, unsigned long final_bits) { @@ -1359,7 +1371,7 @@ int cgroup_attach_task(struct cgroup *cgrp, struct task_struct *tsk) * wake up rmdir() waiter. the rmdir should fail since the cgroup * is no longer empty. */ - cgroup_wakeup_rmdir_waiters(cgrp); + cgroup_wakeup_rmdir_waiter(cgrp); return 0; } @@ -2743,34 +2755,43 @@ again: } mutex_unlock(&cgroup_mutex); + /* + * In general, subsystem has no css->refcnt after pre_destroy(). But + * in racy cases, subsystem may have to get css->refcnt after + * pre_destroy() and it makes rmdir return with -EBUSY. This sometimes + * make rmdir return -EBUSY too often. To avoid that, we use waitqueue + * for cgroup's rmdir. CGRP_WAIT_ON_RMDIR is for synchronizing rmdir + * and subsystem's reference count handling. Please see css_get/put + * and css_tryget() and cgroup_wakeup_rmdir_waiter() implementation. + */ + set_bit(CGRP_WAIT_ON_RMDIR, &cgrp->flags); + /* * Call pre_destroy handlers of subsys. Notify subsystems * that rmdir() request comes. */ ret = cgroup_call_pre_destroy(cgrp); - if (ret) + if (ret) { + clear_bit(CGRP_WAIT_ON_RMDIR, &cgrp->flags); return ret; + } mutex_lock(&cgroup_mutex); parent = cgrp->parent; if (atomic_read(&cgrp->count) || !list_empty(&cgrp->children)) { + clear_bit(CGRP_WAIT_ON_RMDIR, &cgrp->flags); mutex_unlock(&cgroup_mutex); return -EBUSY; } - /* - * css_put/get is provided for subsys to grab refcnt to css. In typical - * case, subsystem has no reference after pre_destroy(). But, under - * hierarchy management, some *temporal* refcnt can be hold. - * To avoid returning -EBUSY to a user, waitqueue is used. If subsys - * is really busy, it should return -EBUSY at pre_destroy(). wake_up - * is called when css_put() is called and refcnt goes down to 0. - */ - set_bit(CGRP_WAIT_ON_RMDIR, &cgrp->flags); prepare_to_wait(&cgroup_rmdir_waitq, &wait, TASK_INTERRUPTIBLE); - if (!cgroup_clear_css_refs(cgrp)) { mutex_unlock(&cgroup_mutex); - schedule(); + /* + * Because someone may call cgroup_wakeup_rmdir_waiter() before + * prepare_to_wait(), we need to check this flag. + */ + if (test_bit(CGRP_WAIT_ON_RMDIR, &cgrp->flags)) + schedule(); finish_wait(&cgroup_rmdir_waitq, &wait); clear_bit(CGRP_WAIT_ON_RMDIR, &cgrp->flags); if (signal_pending(current)) @@ -3342,7 +3363,7 @@ void __css_put(struct cgroup_subsys_state *css) set_bit(CGRP_RELEASABLE, &cgrp->flags); check_for_release(cgrp); } - cgroup_wakeup_rmdir_waiters(cgrp); + cgroup_wakeup_rmdir_waiter(cgrp); } rcu_read_unlock(); } diff --git a/mm/memcontrol.c b/mm/memcontrol.c index e717964cb5a..fd4529d86de 100644 --- a/mm/memcontrol.c +++ b/mm/memcontrol.c @@ -1207,6 +1207,12 @@ static int mem_cgroup_move_account(struct page_cgroup *pc, ret = 0; out: unlock_page_cgroup(pc); + /* + * We charges against "to" which may not have any tasks. Then, "to" + * can be under rmdir(). But in current implementation, caller of + * this function is just force_empty() and it's garanteed that + * "to" is never removed. So, we don't check rmdir status here. + */ return ret; } @@ -1428,6 +1434,7 @@ __mem_cgroup_commit_charge_swapin(struct page *page, struct mem_cgroup *ptr, return; if (!ptr) return; + cgroup_exclude_rmdir(&ptr->css); pc = lookup_page_cgroup(page); mem_cgroup_lru_del_before_commit_swapcache(page); __mem_cgroup_commit_charge(ptr, pc, ctype); @@ -1457,8 +1464,12 @@ __mem_cgroup_commit_charge_swapin(struct page *page, struct mem_cgroup *ptr, } rcu_read_unlock(); } - /* add this page(page_cgroup) to the LRU we want. */ - + /* + * At swapin, we may charge account against cgroup which has no tasks. + * So, rmdir()->pre_destroy() can be called while we do this charge. + * In that case, we need to call pre_destroy() again. check it here. + */ + cgroup_release_and_wakeup_rmdir(&ptr->css); } void mem_cgroup_commit_charge_swapin(struct page *page, struct mem_cgroup *ptr) @@ -1664,7 +1675,7 @@ void mem_cgroup_end_migration(struct mem_cgroup *mem, if (!mem) return; - + cgroup_exclude_rmdir(&mem->css); /* at migration success, oldpage->mapping is NULL. */ if (oldpage->mapping) { target = oldpage; @@ -1704,6 +1715,12 @@ void mem_cgroup_end_migration(struct mem_cgroup *mem, */ if (ctype == MEM_CGROUP_CHARGE_TYPE_MAPPED) mem_cgroup_uncharge_page(target); + /* + * At migration, we may charge account against cgroup which has no tasks + * So, rmdir()->pre_destroy() can be called while we do this charge. + * In that case, we need to call pre_destroy() again. check it here. + */ + cgroup_release_and_wakeup_rmdir(&mem->css); } /* -- GitLab From 1fc28b70fe2dbf87e061b6ce5091a1f8e4e5d4e7 Mon Sep 17 00:00:00 2001 From: Mel Gorman Date: Wed, 29 Jul 2009 15:04:08 -0700 Subject: [PATCH 0520/1342] page-allocator: allow too high-order warning messages to be suppressed with __GFP_NOWARN The page allocator warns once when an order >= MAX_ORDER is specified. This is to catch callers of the allocator that are always falling back to their worst-case when it was not expected. However, there are cases where the caller is behaving correctly but cannot suppress the warning. This patch allows the warning to be suppressed by the callers by specifying __GFP_NOWARN. Signed-off-by: Mel Gorman Acked-by: David Rientjes Cc: Arnaldo Carvalho de Melo Cc: "David S. Miller" Cc: "Rafael J. Wysocki" Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- mm/page_alloc.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/mm/page_alloc.c b/mm/page_alloc.c index 2dbb2fc6883..d052abbe306 100644 --- a/mm/page_alloc.c +++ b/mm/page_alloc.c @@ -1745,8 +1745,10 @@ __alloc_pages_slowpath(gfp_t gfp_mask, unsigned int order, * be using allocators in order of preference for an area that is * too large. */ - if (WARN_ON_ONCE(order >= MAX_ORDER)) + if (order >= MAX_ORDER) { + WARN_ON_ONCE(!(gfp_mask & __GFP_NOWARN)); return NULL; + } /* * GFP_THISNODE (meaning __GFP_THISNODE, __GFP_NORETRY and -- GitLab From b62f495dad04fa94b5083aec638ff3072bccaaca Mon Sep 17 00:00:00 2001 From: Mel Gorman Date: Wed, 29 Jul 2009 15:04:09 -0700 Subject: [PATCH 0521/1342] profile: suppress warning about large allocations when profile=1 is specified When profile= is used, a large buffer is allocated early at boot. This can be larger than what the page allocator can provide so it prints a warning. However, the caller is able to handle the situation so this patch suppresses the warning. Signed-off-by: Mel Gorman Cc: "Rafael J. Wysocki" Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- kernel/profile.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/kernel/profile.c b/kernel/profile.c index 69911b5745e..419250ebec4 100644 --- a/kernel/profile.c +++ b/kernel/profile.c @@ -117,11 +117,12 @@ int __ref profile_init(void) cpumask_copy(prof_cpu_mask, cpu_possible_mask); - prof_buffer = kzalloc(buffer_bytes, GFP_KERNEL); + prof_buffer = kzalloc(buffer_bytes, GFP_KERNEL|__GFP_NOWARN); if (prof_buffer) return 0; - prof_buffer = alloc_pages_exact(buffer_bytes, GFP_KERNEL|__GFP_ZERO); + prof_buffer = alloc_pages_exact(buffer_bytes, + GFP_KERNEL|__GFP_ZERO|__GFP_NOWARN); if (prof_buffer) return 0; -- GitLab From 1c29b3ff4f2d847464f7be3a0e179c6dfc69bd02 Mon Sep 17 00:00:00 2001 From: Mel Gorman Date: Wed, 29 Jul 2009 15:04:10 -0700 Subject: [PATCH 0522/1342] net-dccp: suppress warning about large allocations from DCCP The DCCP protocol tries to allocate some large hash tables during initialisation using the largest size possible. This can be larger than what the page allocator can provide so it prints a warning. However, the caller is able to handle the situation so this patch suppresses the warning. Signed-off-by: Mel Gorman Acked-by: Arnaldo Carvalho de Melo Cc: "David S. Miller" Cc: "Rafael J. Wysocki" Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- net/dccp/proto.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/net/dccp/proto.c b/net/dccp/proto.c index 94ca8eaace7..3281013ce03 100644 --- a/net/dccp/proto.c +++ b/net/dccp/proto.c @@ -1066,7 +1066,7 @@ static int __init dccp_init(void) (dccp_hashinfo.ehash_size - 1)) dccp_hashinfo.ehash_size--; dccp_hashinfo.ehash = (struct inet_ehash_bucket *) - __get_free_pages(GFP_ATOMIC, ehash_order); + __get_free_pages(GFP_ATOMIC|__GFP_NOWARN, ehash_order); } while (!dccp_hashinfo.ehash && --ehash_order > 0); if (!dccp_hashinfo.ehash) { @@ -1091,7 +1091,7 @@ static int __init dccp_init(void) bhash_order > 0) continue; dccp_hashinfo.bhash = (struct inet_bind_hashbucket *) - __get_free_pages(GFP_ATOMIC, bhash_order); + __get_free_pages(GFP_ATOMIC|__GFP_NOWARN, bhash_order); } while (!dccp_hashinfo.bhash && --bhash_order >= 0); if (!dccp_hashinfo.bhash) { -- GitLab From 5c8053652328693d10551131432ef3573e77ed2d Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Wed, 29 Jul 2009 15:04:11 -0700 Subject: [PATCH 0523/1342] fs/ramfs/file-nommu.c needs include/linux/sched.h This file makes use of various macros defined in files like asm/current.h or asm-generic/resource.h. All these files can be included via sched.h. The building of the !MMU ARM kernel (with additional patches) fails without this change. Signed-off-by: Catalin Marinas Acked-by: David Howells Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- fs/ramfs/file-nommu.c | 1 + 1 file changed, 1 insertion(+) diff --git a/fs/ramfs/file-nommu.c b/fs/ramfs/file-nommu.c index ebb2c417912..11f0c06316d 100644 --- a/fs/ramfs/file-nommu.c +++ b/fs/ramfs/file-nommu.c @@ -20,6 +20,7 @@ #include #include #include +#include #include #include "internal.h" -- GitLab From f5a55efa140f5e9c9dd0f398fef54f20cdb74ec9 Mon Sep 17 00:00:00 2001 From: Dave Jones Date: Wed, 29 Jul 2009 15:04:12 -0700 Subject: [PATCH 0524/1342] pps.h needs Found with make headers_check /usr/include/linux/pps.h:52: found __[us]{8,16,32,64} type without #include Signed-off-by: Dave Jones Cc: Rodolfo Giometti Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- include/linux/pps.h | 2 ++ 1 file changed, 2 insertions(+) diff --git a/include/linux/pps.h b/include/linux/pps.h index cfe5c7214ec..0194ab06177 100644 --- a/include/linux/pps.h +++ b/include/linux/pps.h @@ -22,6 +22,8 @@ #ifndef _PPS_H_ #define _PPS_H_ +#include + #define PPS_VERSION "5.3.6" #define PPS_MAX_SOURCES 16 /* should be enough... */ -- GitLab From cab8bd3410d448279e3bd0fbf96d31db0bf770fa Mon Sep 17 00:00:00 2001 From: Hidetoshi Seto Date: Wed, 29 Jul 2009 15:04:14 -0700 Subject: [PATCH 0525/1342] sysrq, kdump: make sysrq-c consistent commit d6580a9f15238b87e618310c862231ae3f352d2d ("kexec: sysrq: simplify sysrq-c handler") changed the behavior of sysrq-c to unconditional dereference of NULL pointer. So in cases with CONFIG_KEXEC, where crash_kexec() was directly called from sysrq-c before, now it can be said that a step of "real oops" was inserted before starting kdump. However, in contrast to oops via SysRq-c from keyboard which results in panic due to in_interrupt(), oops via "echo c > /proc/sysrq-trigger" will not become panic unless panic_on_oops=1. It means that even if dump is properly configured to be taken on panic, the sysrq-c from proc interface might not start crashdump while the sysrq-c from keyboard can start crashdump. This confuses traditional users of kdump, i.e. people who expect sysrq-c to do common behavior in both of the keyboard and proc interface. This patch brings the keyboard and proc interface behavior of sysrq-c in line, by forcing panic_on_oops=1 before oops in sysrq-c handler. And some updates in documentation are included, to clarify that there is no longer dependency with CONFIG_KEXEC, and that now the system can just crash by sysrq-c if no dump mechanism is configured. Signed-off-by: Hidetoshi Seto Cc: Lai Jiangshan Cc: Ken'ichi Ohmichi Acked-by: Neil Horman Acked-by: Vivek Goyal Cc: Brayan Arraes Cc: Eric W. Biederman Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/sysrq.txt | 7 ++++--- drivers/char/sysrq.c | 8 +++++--- 2 files changed, 9 insertions(+), 6 deletions(-) diff --git a/Documentation/sysrq.txt b/Documentation/sysrq.txt index cf42b820ff9..d56a0177542 100644 --- a/Documentation/sysrq.txt +++ b/Documentation/sysrq.txt @@ -66,7 +66,8 @@ On all - write a character to /proc/sysrq-trigger. e.g.: 'b' - Will immediately reboot the system without syncing or unmounting your disks. -'c' - Will perform a kexec reboot in order to take a crashdump. +'c' - Will perform a system crash by a NULL pointer dereference. + A crashdump will be taken if configured. 'd' - Shows all locks that are held. @@ -141,8 +142,8 @@ useful when you want to exit a program that will not let you switch consoles. re'B'oot is good when you're unable to shut down. But you should also 'S'ync and 'U'mount first. -'C'rashdump can be used to manually trigger a crashdump when the system is hung. -The kernel needs to have been built with CONFIG_KEXEC enabled. +'C'rash can be used to manually trigger a crashdump when the system is hung. +Note that this just triggers a crash if there is no dump mechanism available. 'S'ync is great when your system is locked up, it allows you to sync your disks and will certainly lessen the chance of data loss and fscking. Note diff --git a/drivers/char/sysrq.c b/drivers/char/sysrq.c index 0db35857e4d..5d7a02f63e1 100644 --- a/drivers/char/sysrq.c +++ b/drivers/char/sysrq.c @@ -35,7 +35,6 @@ #include #include #include -#include #include #include @@ -124,9 +123,12 @@ static struct sysrq_key_op sysrq_unraw_op = { static void sysrq_handle_crash(int key, struct tty_struct *tty) { char *killer = NULL; + + panic_on_oops = 1; /* force panic */ + wmb(); *killer = 1; } -static struct sysrq_key_op sysrq_crashdump_op = { +static struct sysrq_key_op sysrq_crash_op = { .handler = sysrq_handle_crash, .help_msg = "Crash", .action_msg = "Trigger a crash", @@ -401,7 +403,7 @@ static struct sysrq_key_op *sysrq_key_table[36] = { */ NULL, /* a */ &sysrq_reboot_op, /* b */ - &sysrq_crashdump_op, /* c & ibm_emac driver debug */ + &sysrq_crash_op, /* c & ibm_emac driver debug */ &sysrq_showlocks_op, /* d */ &sysrq_term_op, /* e */ &sysrq_moom_op, /* f */ -- GitLab From a9e58f25734e153b8c6516d904e2398fb8b0b23d Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Wed, 29 Jul 2009 15:04:16 -0700 Subject: [PATCH 0526/1342] sdhci: get rid of "frequency too high" flood when using eSDHC Since commit 8dfd0374be84793360db7fff2e635d2cd3bbcb21 ("MMC core: limit minimum initialization frequency to 400kHz") MMC core checks for minimum frequency, and that causes following messages flood when using eSDHC controllers: ... mmc0: Minimum clock frequency too high for identification mode mmc0: Minimum clock frequency too high for identification mode ... The warnings are legitimate, since if we'd use 133 MHz clocks for standard SDHCI controllers, we'd not able to scale frequency down to 400 kHz. But eSDHC controllers have a non-standard SD clock management, so we can divide clock by 256 * 16, not just 256. This patch introduces get_min_clock() callback for sdhci core and implements it for sdhci-of driver, and thus fixes the issue. Signed-off-by: Anton Vorontsov Cc: Matt Fleming Cc: Ian Molton Cc: "Roberto A. Foglietta" Cc: Pierre Ossman Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/mmc/host/sdhci-of.c | 8 ++++++++ drivers/mmc/host/sdhci.c | 5 ++++- drivers/mmc/host/sdhci.h | 1 + 3 files changed, 13 insertions(+), 1 deletion(-) diff --git a/drivers/mmc/host/sdhci-of.c b/drivers/mmc/host/sdhci-of.c index d79fa55c3b8..908844327db 100644 --- a/drivers/mmc/host/sdhci-of.c +++ b/drivers/mmc/host/sdhci-of.c @@ -158,6 +158,13 @@ static unsigned int esdhc_get_max_clock(struct sdhci_host *host) return of_host->clock; } +static unsigned int esdhc_get_min_clock(struct sdhci_host *host) +{ + struct sdhci_of_host *of_host = sdhci_priv(host); + + return of_host->clock / 256 / 16; +} + static unsigned int esdhc_get_timeout_clock(struct sdhci_host *host) { struct sdhci_of_host *of_host = sdhci_priv(host); @@ -184,6 +191,7 @@ static struct sdhci_of_data sdhci_esdhc = { .set_clock = esdhc_set_clock, .enable_dma = esdhc_enable_dma, .get_max_clock = esdhc_get_max_clock, + .get_min_clock = esdhc_get_min_clock, .get_timeout_clock = esdhc_get_timeout_clock, }, }; diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index 6779b4ecab1..62041c7e924 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -1766,7 +1766,10 @@ int sdhci_add_host(struct sdhci_host *host) * Set host parameters. */ mmc->ops = &sdhci_ops; - mmc->f_min = host->max_clk / 256; + if (host->ops->get_min_clock) + mmc->f_min = host->ops->get_min_clock(host); + else + mmc->f_min = host->max_clk / 256; mmc->f_max = host->max_clk; mmc->caps = MMC_CAP_SDIO_IRQ; diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h index 831ddf7dcb4..c77e9ff3022 100644 --- a/drivers/mmc/host/sdhci.h +++ b/drivers/mmc/host/sdhci.h @@ -302,6 +302,7 @@ struct sdhci_ops { int (*enable_dma)(struct sdhci_host *host); unsigned int (*get_max_clock)(struct sdhci_host *host); + unsigned int (*get_min_clock)(struct sdhci_host *host); unsigned int (*get_timeout_clock)(struct sdhci_host *host); }; -- GitLab From 534acc057b5a08ec33fa57cdd2f5a09ef124e7f2 Mon Sep 17 00:00:00 2001 From: Dave Hansen Date: Wed, 29 Jul 2009 15:04:18 -0700 Subject: [PATCH 0527/1342] lib: flexible array implementation Once a structure goes over PAGE_SIZE*2, we see occasional allocation failures. Some people have chosen to switch over to things like vmalloc() that will let them keep array-like access to such a large structures. But, vmalloc() has plenty of downsides. Here's an alternative. I think it's what Andrew was suggesting here: http://lkml.org/lkml/2009/7/2/518 I call it a flexible array. It does all of its work in PAGE_SIZE bits, so never does an order>0 allocation. The base level has PAGE_SIZE-2*sizeof(int) bytes of storage for pointers to the second level. So, with a 32-bit arch, you get about 4MB (4183112 bytes) of total storage when the objects pack nicely into a page. It is half that on 64-bit because the pointers are twice the size. There's a table detailing this in the code. There are kerneldocs for the functions, but here's an overview: flex_array_alloc() - dynamically allocate a base structure flex_array_free() - free the array and all of the second-level pages flex_array_free_parts() - free the second-level pages, but not the base (for static bases) flex_array_put() - copy into the array at the given index flex_array_get() - copy out of the array at the given index flex_array_prealloc() - preallocate the second-level pages between the given indexes to guarantee no allocs will occur at put() time. We could also potentially just pass the "element_size" into each of the API functions instead of storing it internally. That would get us one more base pointer on 32-bit. I've been testing this by running it in userspace. The header and patch that I've been using are here, as well as the little script I'm using to generate the size table which goes in the kerneldocs. http://sr71.net/~dave/linux/flexarray/ [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Dave Hansen Reviewed-by: KAMEZAWA Hiroyuki Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- include/linux/flex_array.h | 47 +++++++ lib/Makefile | 2 +- lib/flex_array.c | 269 +++++++++++++++++++++++++++++++++++++ 3 files changed, 317 insertions(+), 1 deletion(-) create mode 100644 include/linux/flex_array.h create mode 100644 lib/flex_array.c diff --git a/include/linux/flex_array.h b/include/linux/flex_array.h new file mode 100644 index 00000000000..23c1ec79a31 --- /dev/null +++ b/include/linux/flex_array.h @@ -0,0 +1,47 @@ +#ifndef _FLEX_ARRAY_H +#define _FLEX_ARRAY_H + +#include +#include + +#define FLEX_ARRAY_PART_SIZE PAGE_SIZE +#define FLEX_ARRAY_BASE_SIZE PAGE_SIZE + +struct flex_array_part; + +/* + * This is meant to replace cases where an array-like + * structure has gotten too big to fit into kmalloc() + * and the developer is getting tempted to use + * vmalloc(). + */ + +struct flex_array { + union { + struct { + int element_size; + int total_nr_elements; + struct flex_array_part *parts[0]; + }; + /* + * This little trick makes sure that + * sizeof(flex_array) == PAGE_SIZE + */ + char padding[FLEX_ARRAY_BASE_SIZE]; + }; +}; + +#define FLEX_ARRAY_INIT(size, total) { { {\ + .element_size = (size), \ + .total_nr_elements = (total), \ +} } } + +struct flex_array *flex_array_alloc(int element_size, int total, gfp_t flags); +int flex_array_prealloc(struct flex_array *fa, int start, int end, gfp_t flags); +void flex_array_free(struct flex_array *fa); +void flex_array_free_parts(struct flex_array *fa); +int flex_array_put(struct flex_array *fa, int element_nr, void *src, + gfp_t flags); +void *flex_array_get(struct flex_array *fa, int element_nr); + +#endif /* _FLEX_ARRAY_H */ diff --git a/lib/Makefile b/lib/Makefile index b6d1857bbf0..2e78277eff9 100644 --- a/lib/Makefile +++ b/lib/Makefile @@ -12,7 +12,7 @@ lib-y := ctype.o string.o vsprintf.o cmdline.o \ idr.o int_sqrt.o extable.o prio_tree.o \ sha1.o irq_regs.o reciprocal_div.o argv_split.o \ proportions.o prio_heap.o ratelimit.o show_mem.o \ - is_single_threaded.o plist.o decompress.o + is_single_threaded.o plist.o decompress.o flex_array.o lib-$(CONFIG_MMU) += ioremap.o lib-$(CONFIG_SMP) += cpumask.o diff --git a/lib/flex_array.c b/lib/flex_array.c new file mode 100644 index 00000000000..0e7894ce888 --- /dev/null +++ b/lib/flex_array.c @@ -0,0 +1,269 @@ +/* + * Flexible array managed in PAGE_SIZE parts + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + * + * Copyright IBM Corporation, 2009 + * + * Author: Dave Hansen + */ + +#include +#include +#include + +struct flex_array_part { + char elements[FLEX_ARRAY_PART_SIZE]; +}; + +static inline int __elements_per_part(int element_size) +{ + return FLEX_ARRAY_PART_SIZE / element_size; +} + +static inline int bytes_left_in_base(void) +{ + int element_offset = offsetof(struct flex_array, parts); + int bytes_left = FLEX_ARRAY_BASE_SIZE - element_offset; + return bytes_left; +} + +static inline int nr_base_part_ptrs(void) +{ + return bytes_left_in_base() / sizeof(struct flex_array_part *); +} + +/* + * If a user requests an allocation which is small + * enough, we may simply use the space in the + * flex_array->parts[] array to store the user + * data. + */ +static inline int elements_fit_in_base(struct flex_array *fa) +{ + int data_size = fa->element_size * fa->total_nr_elements; + if (data_size <= bytes_left_in_base()) + return 1; + return 0; +} + +/** + * flex_array_alloc - allocate a new flexible array + * @element_size: the size of individual elements in the array + * @total: total number of elements that this should hold + * + * Note: all locking must be provided by the caller. + * + * @total is used to size internal structures. If the user ever + * accesses any array indexes >=@total, it will produce errors. + * + * The maximum number of elements is defined as: the number of + * elements that can be stored in a page times the number of + * page pointers that we can fit in the base structure or (using + * integer math): + * + * (PAGE_SIZE/element_size) * (PAGE_SIZE-8)/sizeof(void *) + * + * Here's a table showing example capacities. Note that the maximum + * index that the get/put() functions is just nr_objects-1. This + * basically means that you get 4MB of storage on 32-bit and 2MB on + * 64-bit. + * + * + * Element size | Objects | Objects | + * PAGE_SIZE=4k | 32-bit | 64-bit | + * ---------------------------------| + * 1 bytes | 4186112 | 2093056 | + * 2 bytes | 2093056 | 1046528 | + * 3 bytes | 1395030 | 697515 | + * 4 bytes | 1046528 | 523264 | + * 32 bytes | 130816 | 65408 | + * 33 bytes | 126728 | 63364 | + * 2048 bytes | 2044 | 1022 | + * 2049 bytes | 1022 | 511 | + * void * | 1046528 | 261632 | + * + * Since 64-bit pointers are twice the size, we lose half the + * capacity in the base structure. Also note that no effort is made + * to efficiently pack objects across page boundaries. + */ +struct flex_array *flex_array_alloc(int element_size, int total, gfp_t flags) +{ + struct flex_array *ret; + int max_size = nr_base_part_ptrs() * __elements_per_part(element_size); + + /* max_size will end up 0 if element_size > PAGE_SIZE */ + if (total > max_size) + return NULL; + ret = kzalloc(sizeof(struct flex_array), flags); + if (!ret) + return NULL; + ret->element_size = element_size; + ret->total_nr_elements = total; + return ret; +} + +static int fa_element_to_part_nr(struct flex_array *fa, int element_nr) +{ + return element_nr / __elements_per_part(fa->element_size); +} + +/** + * flex_array_free_parts - just free the second-level pages + * @src: address of data to copy into the array + * @element_nr: index of the position in which to insert + * the new element. + * + * This is to be used in cases where the base 'struct flex_array' + * has been statically allocated and should not be free. + */ +void flex_array_free_parts(struct flex_array *fa) +{ + int part_nr; + int max_part = nr_base_part_ptrs(); + + if (elements_fit_in_base(fa)) + return; + for (part_nr = 0; part_nr < max_part; part_nr++) + kfree(fa->parts[part_nr]); +} + +void flex_array_free(struct flex_array *fa) +{ + flex_array_free_parts(fa); + kfree(fa); +} + +static int fa_index_inside_part(struct flex_array *fa, int element_nr) +{ + return element_nr % __elements_per_part(fa->element_size); +} + +static int index_inside_part(struct flex_array *fa, int element_nr) +{ + int part_offset = fa_index_inside_part(fa, element_nr); + return part_offset * fa->element_size; +} + +static struct flex_array_part * +__fa_get_part(struct flex_array *fa, int part_nr, gfp_t flags) +{ + struct flex_array_part *part = fa->parts[part_nr]; + if (!part) { + /* + * This leaves the part pages uninitialized + * and with potentially random data, just + * as if the user had kmalloc()'d the whole. + * __GFP_ZERO can be used to zero it. + */ + part = kmalloc(FLEX_ARRAY_PART_SIZE, flags); + if (!part) + return NULL; + fa->parts[part_nr] = part; + } + return part; +} + +/** + * flex_array_put - copy data into the array at @element_nr + * @src: address of data to copy into the array + * @element_nr: index of the position in which to insert + * the new element. + * + * Note that this *copies* the contents of @src into + * the array. If you are trying to store an array of + * pointers, make sure to pass in &ptr instead of ptr. + * + * Locking must be provided by the caller. + */ +int flex_array_put(struct flex_array *fa, int element_nr, void *src, gfp_t flags) +{ + int part_nr = fa_element_to_part_nr(fa, element_nr); + struct flex_array_part *part; + void *dst; + + if (element_nr >= fa->total_nr_elements) + return -ENOSPC; + if (elements_fit_in_base(fa)) + part = (struct flex_array_part *)&fa->parts[0]; + else + part = __fa_get_part(fa, part_nr, flags); + if (!part) + return -ENOMEM; + dst = &part->elements[index_inside_part(fa, element_nr)]; + memcpy(dst, src, fa->element_size); + return 0; +} + +/** + * flex_array_prealloc - guarantee that array space exists + * @start: index of first array element for which space is allocated + * @end: index of last (inclusive) element for which space is allocated + * + * This will guarantee that no future calls to flex_array_put() + * will allocate memory. It can be used if you are expecting to + * be holding a lock or in some atomic context while writing + * data into the array. + * + * Locking must be provided by the caller. + */ +int flex_array_prealloc(struct flex_array *fa, int start, int end, gfp_t flags) +{ + int start_part; + int end_part; + int part_nr; + struct flex_array_part *part; + + if (start >= fa->total_nr_elements || end >= fa->total_nr_elements) + return -ENOSPC; + if (elements_fit_in_base(fa)) + return 0; + start_part = fa_element_to_part_nr(fa, start); + end_part = fa_element_to_part_nr(fa, end); + for (part_nr = start_part; part_nr <= end_part; part_nr++) { + part = __fa_get_part(fa, part_nr, flags); + if (!part) + return -ENOMEM; + } + return 0; +} + +/** + * flex_array_get - pull data back out of the array + * @element_nr: index of the element to fetch from the array + * + * Returns a pointer to the data at index @element_nr. Note + * that this is a copy of the data that was passed in. If you + * are using this to store pointers, you'll get back &ptr. + * + * Locking must be provided by the caller. + */ +void *flex_array_get(struct flex_array *fa, int element_nr) +{ + int part_nr = fa_element_to_part_nr(fa, element_nr); + struct flex_array_part *part; + int index; + + if (element_nr >= fa->total_nr_elements) + return NULL; + if (!fa->parts[part_nr]) + return NULL; + if (elements_fit_in_base(fa)) + part = (struct flex_array_part *)&fa->parts[0]; + else + part = fa->parts[part_nr]; + index = index_inside_part(fa, element_nr); + return &part->elements[index_inside_part(fa, element_nr)]; +} -- GitLab From 8da14b5fc32368f582df09fe9c0bec2507868583 Mon Sep 17 00:00:00 2001 From: Albin Tonnerre Date: Wed, 29 Jul 2009 15:04:18 -0700 Subject: [PATCH 0528/1342] drivers/serial/atmel_serial.c: fix compile when CONFIG_SERIAL_ATMEL=Y and CONFIG_SERIAL_ATMEL_CONSOLE=N When SERIAL_ATMEL_CONSOLE is disabled, ATMEL_CONSOLE_DEVICE is set to NULL, and trying to access ATMEL_CONSOLE_DEVICE->flags in atmel_serial_probe makes the compile fail. This fixes the issue by only accessing it if CONFIG_SERIAL_ATMEL_CONSOLE is defined Signed-off-by: Albin Tonnerre Signed-off-by: Haavard Skinnemoen Cc: Nicolas Ferre Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/serial/atmel_serial.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/serial/atmel_serial.c b/drivers/serial/atmel_serial.c index 338b15c0a54..607d43a3104 100644 --- a/drivers/serial/atmel_serial.c +++ b/drivers/serial/atmel_serial.c @@ -1551,6 +1551,7 @@ static int __devinit atmel_serial_probe(struct platform_device *pdev) if (ret) goto err_add_port; +#ifdef CONFIG_SERIAL_ATMEL_CONSOLE if (atmel_is_console_port(&port->uart) && ATMEL_CONSOLE_DEVICE->flags & CON_ENABLED) { /* @@ -1559,6 +1560,7 @@ static int __devinit atmel_serial_probe(struct platform_device *pdev) */ clk_disable(port->clk); } +#endif device_init_wakeup(&pdev->dev, 1); platform_set_drvdata(pdev, port); -- GitLab From 812ed032cdc8138b7546eecc996879756b92d801 Mon Sep 17 00:00:00 2001 From: Jiri Slaby Date: Wed, 29 Jul 2009 15:04:19 -0700 Subject: [PATCH 0529/1342] uio: mark uio.h functions __KERNEL__ only To avoid userspace build failures such as: .../linux/uio.h:37: error: expected `=', `,', `;', `asm' or `__attribute__' before `iov_length' .../linux/uio.h:47: error: expected declaration specifiers or `...' before `size_t' move uio functions inside a __KERNEL__ block. Signed-off-by: Jiri Slaby Acked-by: Sam Ravnborg Cc: Alexander Viro Cc: Christoph Hellwig Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- include/linux/uio.h | 17 ++++++++--------- 1 file changed, 8 insertions(+), 9 deletions(-) diff --git a/include/linux/uio.h b/include/linux/uio.h index b7fe13883bd..98c114323a8 100644 --- a/include/linux/uio.h +++ b/include/linux/uio.h @@ -19,15 +19,6 @@ struct iovec __kernel_size_t iov_len; /* Must be size_t (1003.1g) */ }; -#ifdef __KERNEL__ - -struct kvec { - void *iov_base; /* and that should *never* hold a userland pointer */ - size_t iov_len; -}; - -#endif - /* * UIO_MAXIOV shall be at least 16 1003.1g (5.4.1.1) */ @@ -35,6 +26,13 @@ struct kvec { #define UIO_FASTIOV 8 #define UIO_MAXIOV 1024 +#ifdef __KERNEL__ + +struct kvec { + void *iov_base; /* and that should *never* hold a userland pointer */ + size_t iov_len; +}; + /* * Total number of bytes covered by an iovec. * @@ -53,5 +51,6 @@ static inline size_t iov_length(const struct iovec *iov, unsigned long nr_segs) } unsigned long iov_shorten(struct iovec *iov, unsigned long nr_segs, size_t to); +#endif #endif -- GitLab From 56d44f05177e69b757a01987827db8ef79fb759c Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:20 -0700 Subject: [PATCH 0530/1342] MAINTAINERS: IA64 - pair P:/M: entries properly Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/MAINTAINERS b/MAINTAINERS index ebc269152fa..5fe36a33ca6 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2858,8 +2858,8 @@ S: Maintained IA64 (Itanium) PLATFORM P: Tony Luck -P: Fenghua Yu M: tony.luck@intel.com +P: Fenghua Yu M: fenghua.yu@intel.com L: linux-ia64@vger.kernel.org W: http://www.ia64-linux.org/ -- GitLab From 30e10993512c94daf0ab5cb4b512979aa1c85daf Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:21 -0700 Subject: [PATCH 0531/1342] MAINTAINERS: Remove ivtv-user lists, add CX18 url Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index 5fe36a33ca6..104850879f2 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1728,10 +1728,10 @@ M: hverkuil@xs4all.nl P: Andy Walls M: awalls@radix.net L: ivtv-devel@ivtvdriver.org -L: ivtv-users@ivtvdriver.org L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git W: http://linuxtv.org +W: http://www.ivtvdriver.org/index.php/Cx18 S: Maintained F: Documentation/video4linux/cx18.txt F: drivers/media/video/cx18/ @@ -3283,7 +3283,6 @@ IVTV VIDEO4LINUX DRIVER P: Hans Verkuil M: hverkuil@xs4all.nl L: ivtv-devel@ivtvdriver.org -L: ivtv-users@ivtvdriver.org L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git W: http://www.ivtvdriver.org -- GitLab From 4cbfbe256dc0b0491351bc5bea89f229cfae2284 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:21 -0700 Subject: [PATCH 0532/1342] MAINTAINERS: QLGE 10Gb ETHERNET - pair P:/M: entries properly Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/MAINTAINERS b/MAINTAINERS index 104850879f2..a6d6420d5b1 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -4821,8 +4821,8 @@ F: drivers/net/qla3xxx.* QLOGIC QLGE 10Gb ETHERNET DRIVER P: Ron Mercer -M: linux-driver@qlogic.com M: ron.mercer@qlogic.com +M: linux-driver@qlogic.com L: netdev@vger.kernel.org S: Supported F: drivers/net/qlge/ -- GitLab From 4fc26e36acce714ca26b576e3e6862887fa130d3 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:22 -0700 Subject: [PATCH 0533/1342] MAINTAINERS: Use tabs in ACER ASPIRE ONE Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index a6d6420d5b1..6504fb916a1 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -231,11 +231,11 @@ S: Maintained F: drivers/net/acenic* ACER ASPIRE ONE TEMPERATURE AND FAN DRIVER -P: Peter Feuerer -M: peter@piie.net -W: http://piie.net/?section=acerhdf -S: Maintained -F: drivers/platform/x86/acerhdf.c +P: Peter Feuerer +M: peter@piie.net +W: http://piie.net/?section=acerhdf +S: Maintained +F: drivers/platform/x86/acerhdf.c ACER WMI LAPTOP EXTRAS P: Carlos Corbacho -- GitLab From 5daa2963f8bd51c161d5b244e439e0c9fdec358b Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:23 -0700 Subject: [PATCH 0534/1342] MAINTAINERS: Remove L: linux-kernel@vger.kernel.org from sections that should not have them. Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 5 ----- 1 file changed, 5 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index 6504fb916a1..7d10f06d088 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2204,7 +2204,6 @@ F: drivers/scsi/lpfc/ ENE CB710 FLASH CARD READER DRIVER P: Michał Mirosław M: mirq-linux@rere.qmqm.pl -L: linux-kernel@vger.kernel.org S: Maintained F: drivers/misc/cb710/ F: drivers/mmc/host/cb710-mmc.* @@ -3480,13 +3479,11 @@ P: Vegard Nossum M: vegardno@ifi.uio.no P Pekka Enberg M: penberg@cs.helsinki.fi -L: linux-kernel@vger.kernel.org S: Maintained KMEMLEAK P: Catalin Marinas M: catalin.marinas@arm.com -L: linux-kernel@vger.kernel.org S: Maintained F: Documentation/kmemleak.txt F: include/linux/kmemleak.h @@ -4306,7 +4303,6 @@ F: drivers/video/omap/ OMAP MMC SUPPORT P: Jarkko Lavinen M: jarkko.lavinen@nokia.com -L: linux-kernel@vger.kernel.org L: linux-omap@vger.kernel.org S: Maintained F: drivers/mmc/host/*omap* @@ -4588,7 +4584,6 @@ P: Paul Mackerras M: paulus@samba.org P: Ingo Molnar M: mingo@elte.hu -L: linux-kernel@vger.kernel.org S: Supported PERSONALITY HANDLING -- GitLab From eb51b0349df8efccc37fc06aa25aecbd4d39551b Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:23 -0700 Subject: [PATCH 0535/1342] MAINTAINERS: Move ARPD to CREDITS Jonathan Layes is hard to find. Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- CREDITS | 3 +++ MAINTAINERS | 6 ------ 2 files changed, 3 insertions(+), 6 deletions(-) diff --git a/CREDITS b/CREDITS index e76d300e9fe..44c13d19e7e 100644 --- a/CREDITS +++ b/CREDITS @@ -2006,6 +2006,9 @@ E: paul@laufernet.com D: Soundblaster driver fixes, ISAPnP quirk S: California, USA +N: Jonathan Layes +D: ARPD support + N: Tom Lees E: tom@lpsg.demon.co.uk W: http://www.lpsg.demon.co.uk/ diff --git a/MAINTAINERS b/MAINTAINERS index 7d10f06d088..b42f1b11fa0 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -951,12 +951,6 @@ W: http://www.arm.linux.org.uk/ S: Maintained F: arch/arm/vfp/ -ARPD SUPPORT -P: Jonathan Layes -L: netdev@vger.kernel.org -S: Maintained -F: net/ipv4/arp.c - ASUS ACPI EXTRAS DRIVER P: Corentin Chary M: corentincj@iksaif.net -- GitLab From 24725d1ecf26ba05d74c1cc3ae7467b61a900421 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:24 -0700 Subject: [PATCH 0536/1342] MAINTAINERS: Update KERNEL JANITORS Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index b42f1b11fa0..7a22e706852 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -3373,10 +3373,9 @@ F: Makefile F: scripts/Makefile.* KERNEL JANITORS -P: Several L: kernel-janitors@vger.kernel.org W: http://www.kerneljanitors.org/ -S: Maintained +S: Odd fixes KERNEL NFSD, SUNRPC, AND LOCKD SERVERS P: J. Bruce Fields -- GitLab From cabaaf415cc9820cfbf2bc86308b94b78e31fe3e Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:24 -0700 Subject: [PATCH 0537/1342] MAINTAINERS: Add PPS patterns Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 3 +++ 1 file changed, 3 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index 7a22e706852..b1859597fa2 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -4667,6 +4667,9 @@ M: giometti@enneenne.com W: http://wiki.enneenne.com/index.php/LinuxPPS_support L: linuxpps@ml.enneenne.com (subscribers-only) S: Maintained +F: Documentation/pps/ +F: drivers/pps/ +F: include/linux/pps*.h PREEMPTIBLE KERNEL P: Robert Love -- GitLab From a72f8024f4c9b06ff35d0bf6df479ea7fae4e2f8 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:25 -0700 Subject: [PATCH 0538/1342] MAINTAINERS: USB Serial Digi Acceleport: use separate P: for Al Borchers Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/MAINTAINERS b/MAINTAINERS index b1859597fa2..b8d6bd35563 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -6105,8 +6105,9 @@ S: Maintained F: drivers/usb/serial/cyberjack.c USB SERIAL DIGI ACCELEPORT DRIVER -P: Peter Berger and Al Borchers +P: Peter Berger M: pberger@brimson.com +P: Al Borchers M: alborchers@steinerpoint.com L: linux-usb@vger.kernel.org S: Maintained -- GitLab From 5bee73ff71e17f5a807376e29653998755211ceb Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:25 -0700 Subject: [PATCH 0539/1342] MAINTAINERS: INPUT: Add Dmitry's name to his email address Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 1 + 1 file changed, 1 insertion(+) diff --git a/MAINTAINERS b/MAINTAINERS index b8d6bd35563..6ef63194996 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2979,6 +2979,7 @@ F: include/linux/inotify.h INPUT (KEYBOARD, MOUSE, JOYSTICK, TOUCHSCREEN) DRIVERS P: Dmitry Torokhov M: dmitry.torokhov@gmail.com +P: Dmitry Torokhov M: dtor@mail.ru L: linux-input@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input.git -- GitLab From 9ae9a7f119a8def8e68d7f5ab0d96b3aba80accb Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:26 -0700 Subject: [PATCH 0540/1342] MAINTAINERS: Remove CS461x sound card section Thomas Woller's email address bounces Nils Faerber isn't active Added Thomas Woller to CREDITS, Nils already has an entry Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- CREDITS | 3 +++ MAINTAINERS | 9 --------- 2 files changed, 3 insertions(+), 9 deletions(-) diff --git a/CREDITS b/CREDITS index 44c13d19e7e..1a41bf4addd 100644 --- a/CREDITS +++ b/CREDITS @@ -3805,6 +3805,9 @@ S: van Bronckhorststraat 12 S: 2612 XV Delft S: The Netherlands +N: Thomas Woller +D: CS461x Cirrus Logic sound driver + N: David Woodhouse E: dwmw2@infradead.org D: JFFS2 file system, Memory Technology Device subsystem, diff --git a/MAINTAINERS b/MAINTAINERS index 6ef63194996..1b02be36d96 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1508,15 +1508,6 @@ L: alsa-devel@alsa-project.org (moderated for non-subscribers) S: Supported F: sound/soc/codecs/cs4270* -CIRRUS LOGIC CS4280/CS461x SOUNDDRIVER -P: Cirrus Logic Corporation (kernel 2.2 driver) -M: Cirrus Logic Corporation, Thomas Woller -P: Nils Faerber (port to kernel 2.4) -M: Nils Faerber -S: Maintained -F: Documentation/input/cs461x.txt -F: sound/pci/cs46xx/ - CLK API P: Russell King M: linux@arm.linux.org.uk -- GitLab From edf4b0a980bf481bbcef0977e2c7369f13f3428f Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:26 -0700 Subject: [PATCH 0541/1342] MAINTAINERS: QLOGIC QLA2XXX - add Andrew Vasquez email address Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 1 + 1 file changed, 1 insertion(+) diff --git a/MAINTAINERS b/MAINTAINERS index 1b02be36d96..8ca15f6a460 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -4788,6 +4788,7 @@ S: Maintained QLOGIC QLA2XXX FC-SCSI DRIVER P: Andrew Vasquez +M: andrew.vasquez@qlogic.com M: linux-driver@qlogic.com L: linux-scsi@vger.kernel.org S: Supported -- GitLab From 2bd1944899354b6f1328fe84886fa8f4d5918aef Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:27 -0700 Subject: [PATCH 0542/1342] MAINTAINERS: QLOGIC QLA3XXX - Add Ron Mercer email address Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 1 + 1 file changed, 1 insertion(+) diff --git a/MAINTAINERS b/MAINTAINERS index 8ca15f6a460..4daf259782e 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -4797,6 +4797,7 @@ F: drivers/scsi/qla2xxx/ QLOGIC QLA3XXX NETWORK DRIVER P: Ron Mercer +M: ron.mercer@qlogic.com M: linux-driver@qlogic.com L: netdev@vger.kernel.org S: Supported -- GitLab From 82c4dfc76200055bd2ae600a08404c10df5f4ff6 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:27 -0700 Subject: [PATCH 0543/1342] MAINTAINERS: Scott Murray is no longer with SomaNetworks Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 9 +++------ 1 file changed, 3 insertions(+), 6 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index 4daf259782e..e4e3471cd0e 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1546,26 +1546,23 @@ F: fs/cifs/ COMPACTPCI HOTPLUG CORE P: Scott Murray -M: scottm@somanetworks.com M: scott@spiteful.org L: linux-pci@vger.kernel.org -S: Supported +S: Maintained F: drivers/pci/hotplug/cpci_hotplug* COMPACTPCI HOTPLUG ZIATECH ZT5550 DRIVER P: Scott Murray -M: scottm@somanetworks.com M: scott@spiteful.org L: linux-pci@vger.kernel.org -S: Supported +S: Maintained F: drivers/pci/hotplug/cpcihp_zt5550.* COMPACTPCI HOTPLUG GENERIC DRIVER P: Scott Murray -M: scottm@somanetworks.com M: scott@spiteful.org L: linux-pci@vger.kernel.org -S: Supported +S: Maintained F: drivers/pci/hotplug/cpcihp_generic.c COMPAL LAPTOP SUPPORT -- GitLab From 870020f93af2323a81f179091a0780dc1d5b916b Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:28 -0700 Subject: [PATCH 0544/1342] scripts/get_maintainer.pl: Add -f directory use Don't require a specific file in a directory to be tested. Also Arnd Bergmann pointed out that the MAINTAINERS pattern requirement that directory patterns have a trailing slash was unnecessary and was likely to be error prone. Removed that requirement. Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- scripts/get_maintainer.pl | 23 +++++++++++++++++++---- 1 file changed, 19 insertions(+), 4 deletions(-) diff --git a/scripts/get_maintainer.pl b/scripts/get_maintainer.pl index 3e733146cd5..7fc09fc91e8 100755 --- a/scripts/get_maintainer.pl +++ b/scripts/get_maintainer.pl @@ -13,7 +13,7 @@ use strict; my $P = $0; -my $V = '0.16'; +my $V = '0.17'; use Getopt::Long qw(:config no_auto_abbrev); @@ -132,6 +132,10 @@ while () { $value =~ s@\.@\\\.@g; ##Convert . to \. $value =~ s/\*/\.\*/g; ##Convert * to .* $value =~ s/\?/\./g; ##Convert ? to . + ##if pattern is a directory and it lacks a trailing slash, add one + if ((-d $value)) { + $value =~ s@([^/])$@$1/@; + } } push(@typevalue, "$type:$value"); } elsif (!/^(\s)*$/) { @@ -146,8 +150,10 @@ close(MAINT); my @files = (); foreach my $file (@ARGV) { - next if ((-d $file)); - if (!(-f $file)) { + ##if $file is a directory and it lacks a trailing slash, add one + if ((-d $file)) { + $file =~ s@([^/])$@$1/@; + } elsif (!(-f $file)) { die "$P: file '${file}' not found\n"; } if ($from_filename) { @@ -292,7 +298,7 @@ sub file_match_pattern { sub usage { print < show version --help => show this help information +Notes: + Using "-f directory" may give unexpected results: + + Used with "--git", git signators for _all_ files in and below + directory are examined as git recurses directories. + Any specified X: (exclude) pattern matches are _not_ ignored. + Used with "--nogit", directory is used as a pattern match, + no individual file within the directory or subdirectory + is matched. EOT } -- GitLab From afa81ee13033de791c41c1d9333853504653939b Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:28 -0700 Subject: [PATCH 0545/1342] get_maintainer.pl: Add git-min-percent option Allow an option to control the minimum percentage of sign-offs required before being considered a maintainer. git-min-percent has a default value of 5 Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- scripts/get_maintainer.pl | 19 ++++++++++++++++--- 1 file changed, 16 insertions(+), 3 deletions(-) diff --git a/scripts/get_maintainer.pl b/scripts/get_maintainer.pl index 7fc09fc91e8..61ef27564ed 100755 --- a/scripts/get_maintainer.pl +++ b/scripts/get_maintainer.pl @@ -27,6 +27,7 @@ my $email_git = 1; my $email_git_penguin_chiefs = 0; my $email_git_min_signatures = 1; my $email_git_max_maintainers = 5; +my $email_git_min_percent = 5; my $email_git_since = "1-year-ago"; my $output_multiline = 1; my $output_separator = ", "; @@ -65,6 +66,7 @@ if (!GetOptions( 'git-chief-penguins!' => \$email_git_penguin_chiefs, 'git-min-signatures=i' => \$email_git_min_signatures, 'git-max-maintainers=i' => \$email_git_max_maintainers, + 'git-min-percent=i' => \$email_git_min_percent, 'git-since=s' => \$email_git_since, 'm!' => \$email_maintainer, 'n!' => \$email_usename, @@ -307,6 +309,7 @@ MAINTAINER field selection options: --git-chief-penguins => include ${penguin_chiefs} --git-min-signatures => number of signatures required (default: 1) --git-max-maintainers => maximum maintainers to add (default: 5) + --git-min-percent => minimum percentage of commits required (default: 0) --git-since => git history to use (default: 1-year-ago) --m => include maintainer(s) if any --n => include name 'Full Name ' @@ -497,6 +500,7 @@ sub recent_git_signoffs { my $output = ""; my $count = 0; my @lines = (); + my $total_sign_offs; if (which("git") eq "") { warn("$P: git not found. Add --nogit to options?\n"); @@ -520,17 +524,26 @@ sub recent_git_signoffs { $output =~ s/^\s*//gm; @lines = split("\n", $output); + + $total_sign_offs = 0; + foreach my $line (@lines) { + if ($line =~ m/([0-9]+)\s+(.*)/) { + $total_sign_offs += $1; + } else { + die("$P: Unexpected git output: ${line}\n"); + } + } + foreach my $line (@lines) { if ($line =~ m/([0-9]+)\s+(.*)/) { my $sign_offs = $1; $line = $2; $count++; if ($sign_offs < $email_git_min_signatures || - $count > $email_git_max_maintainers) { + $count > $email_git_max_maintainers || + $sign_offs * 100 / $total_sign_offs < $email_git_min_percent) { last; } - } else { - die("$P: Unexpected git output: ${line}\n"); } if ($line =~ m/(.+)<(.+)>/) { my $git_name = $1; -- GitLab From 3d202aeb7b7b33d5a5b2040ee5af5b309782941c Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:29 -0700 Subject: [PATCH 0546/1342] get_maintainerpl-add-git-min-percent-option-fix Allow an option to control the minimum percentage of sign-offs required before being considered a maintainer. git-min-percent has a default value of 5 Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- scripts/get_maintainer.pl | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/scripts/get_maintainer.pl b/scripts/get_maintainer.pl index 61ef27564ed..278a45bd45a 100755 --- a/scripts/get_maintainer.pl +++ b/scripts/get_maintainer.pl @@ -309,7 +309,7 @@ MAINTAINER field selection options: --git-chief-penguins => include ${penguin_chiefs} --git-min-signatures => number of signatures required (default: 1) --git-max-maintainers => maximum maintainers to add (default: 5) - --git-min-percent => minimum percentage of commits required (default: 0) + --git-min-percent => minimum percentage of commits required (default: 5) --git-since => git history to use (default: 1-year-ago) --m => include maintainer(s) if any --n => include name 'Full Name ' -- GitLab From 8b58be884a9fd650abb7f7adf3f885fb9cecd79d Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:30 -0700 Subject: [PATCH 0547/1342] MAINTAINERS: coalesce name and email address lines Switch the MAINTAINERS email address format from P: Linus Torvalds M: torvalds@linux-foundation.org to M: Linus Torvalds Mainly to ease the copy-n-pasting of maitnainer addresses into email clients. The script to perform this operation: #! /bin/sh # # Change MAINTAINERS from # P: name # M: address # to: # M: name
# # Integrate P: and M: lines # perl -i -e 'local $/; while(<>) { s@P: ([^\n]+)\nM: ([^\n]+)\n@M: \1 <\2>\n@g; print; }' MAINTAINERS # # Quote names with periods, commas and parentheses # sed -r -i -e "s/^M: (.+)([\.,'\(])(.*) Acked-by: Pavel Machek Acked-by: Randy Dunlap Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 2721 +++++++++++++++++---------------------------------- 1 file changed, 907 insertions(+), 1814 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index e4e3471cd0e..a013e963fc0 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -104,67 +104,58 @@ X: Files and directories that are NOT maintained, same rules as F: matches all files in and below net excluding net/ipv6/ 3C505 NETWORK DRIVER -P: Philip Blundell -M: philb@gnu.org +M: Philip Blundell L: netdev@vger.kernel.org S: Maintained F: drivers/net/3c505* 3C59X NETWORK DRIVER -P: Steffen Klassert -M: klassert@mathematik.tu-chemnitz.de +M: Steffen Klassert L: netdev@vger.kernel.org S: Maintained F: Documentation/networking/vortex.txt F: drivers/net/3c59x.c 3CR990 NETWORK DRIVER -P: David Dillow -M: dave@thedillows.org +M: David Dillow L: netdev@vger.kernel.org S: Maintained F: drivers/net/typhoon* 3W-9XXX SATA-RAID CONTROLLER DRIVER -P: Adam Radford -M: linuxraid@amcc.com +M: Adam Radford L: linux-scsi@vger.kernel.org W: http://www.amcc.com S: Supported F: drivers/scsi/3w-9xxx* 3W-XXXX ATA-RAID CONTROLLER DRIVER -P: Adam Radford -M: linuxraid@amcc.com +M: Adam Radford L: linux-scsi@vger.kernel.org W: http://www.amcc.com S: Supported F: drivers/scsi/3w-xxxx* 53C700 AND 53C700-66 SCSI DRIVER -P: James E.J. Bottomley -M: James.Bottomley@HansenPartnership.com +M: "James E.J. Bottomley" L: linux-scsi@vger.kernel.org S: Maintained F: drivers/scsi/53c700* 6PACK NETWORK DRIVER FOR AX.25 -P: Andreas Koensgen -M: ajk@comnets.uni-bremen.de +M: Andreas Koensgen L: linux-hams@vger.kernel.org S: Maintained F: drivers/net/hamradio/6pack.c 8169 10/100/1000 GIGABIT ETHERNET DRIVER -P: Francois Romieu -M: romieu@fr.zoreil.com +M: Francois Romieu L: netdev@vger.kernel.org S: Maintained F: drivers/net/r8169.c 8250/16?50 (AND CLONE UARTS) SERIAL DRIVER -P: Alan Cox -M: alan@lxorguk.ukuu.org.uk +M: Alan Cox L: linux-serial@vger.kernel.org W: http://serial.sourceforge.net S: Odd Fixes @@ -172,20 +163,16 @@ F: drivers/serial/8250* F: include/linux/serial_8250.h 8390 NETWORK DRIVERS [WD80x3/SMC-ELITE, SMC-ULTRA, NE2000, 3C503, etc.] -P: Paul Gortmaker -M: p_gortmaker@yahoo.com +M: Paul Gortmaker L: netdev@vger.kernel.org S: Maintained F: drivers/net/*8390* F: drivers/net/ax88796.c 9P FILE SYSTEM -P: Eric Van Hensbergen -M: ericvh@gmail.com -P: Ron Minnich -M: rminnich@sandia.gov -P: Latchesar Ionkov -M: lucho@ionkov.net +M: Eric Van Hensbergen +M: Ron Minnich +M: Latchesar Ionkov L: v9fs-developer@lists.sourceforge.net W: http://swik.net/v9fs T: git git://git.kernel.org/pub/scm/linux/kernel/ericvh/v9fs.git @@ -194,15 +181,13 @@ F: Documentation/filesystems/9p.txt F: fs/9p/ A2232 SERIAL BOARD DRIVER -P: Enver Haase -M: A2232@gmx.net +M: Enver Haase L: linux-m68k@lists.linux-m68k.org S: Maintained F: drivers/char/ser_a2232* AACRAID SCSI RAID DRIVER -P: Adaptec OEM Raid Solutions -M: aacraid@adaptec.com +M: Adaptec OEM Raid Solutions L: linux-scsi@vger.kernel.org W: http://www.adaptec.com/ S: Supported @@ -210,44 +195,38 @@ F: Documentation/scsi/aacraid.txt F: drivers/scsi/aacraid/ ABIT UGURU 1,2 HARDWARE MONITOR DRIVER -P: Hans de Goede -M: j.w.r.degoede@hhs.nl +M: Hans de Goede L: lm-sensors@lm-sensors.org S: Maintained F: drivers/hwmon/abituguru.c ABIT UGURU 3 HARDWARE MONITOR DRIVER -P: Alistair John Strachan -M: alistair@devzero.co.uk +M: Alistair John Strachan L: lm-sensors@lm-sensors.org S: Maintained F: drivers/hwmon/abituguru3.c ACENIC DRIVER -P: Jes Sorensen -M: jes@trained-monkey.org +M: Jes Sorensen L: linux-acenic@sunsite.dk S: Maintained F: drivers/net/acenic* ACER ASPIRE ONE TEMPERATURE AND FAN DRIVER -P: Peter Feuerer -M: peter@piie.net +M: Peter Feuerer W: http://piie.net/?section=acerhdf S: Maintained F: drivers/platform/x86/acerhdf.c ACER WMI LAPTOP EXTRAS -P: Carlos Corbacho -M: carlos@strangeworlds.co.uk +M: Carlos Corbacho L: aceracpi@googlegroups.com (subscribers-only) W: http://code.google.com/p/aceracpi S: Maintained F: drivers/platform/x86/acer-wmi.c ACPI -P: Len Brown -M: lenb@kernel.org +M: Len Brown L: linux-acpi@vger.kernel.org W: http://www.lesswatts.org/projects/acpi/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6.git @@ -257,8 +236,7 @@ F: drivers/pnp/pnpacpi/ F: include/linux/acpi.h ACPI BATTERY DRIVERS -P: Alexey Starikovskiy -M: astarikovskiy@suse.de +M: Alexey Starikovskiy L: linux-acpi@vger.kernel.org W: http://www.lesswatts.org/projects/acpi/ S: Supported @@ -266,80 +244,69 @@ F: drivers/acpi/battery.c F: drivers/acpi/*sbs* ACPI EC DRIVER -P: Alexey Starikovskiy -M: astarikovskiy@suse.de +M: Alexey Starikovskiy L: linux-acpi@vger.kernel.org W: http://www.lesswatts.org/projects/acpi/ S: Supported F: drivers/acpi/ec.c ACPI FAN DRIVER -P: Zhang Rui -M: rui.zhang@intel.com +M: Zhang Rui L: linux-acpi@vger.kernel.org W: http://www.lesswatts.org/projects/acpi/ S: Supported F: drivers/acpi/fan.c ACPI PCI HOTPLUG DRIVER -P: Kristen Carlson Accardi -M: kristen.c.accardi@intel.com +M: Kristen Carlson Accardi L: linux-pci@vger.kernel.org S: Supported F: drivers/pci/hotplug/acpi* ACPI THERMAL DRIVER -P: Zhang Rui -M: rui.zhang@intel.com +M: Zhang Rui L: linux-acpi@vger.kernel.org W: http://www.lesswatts.org/projects/acpi/ S: Supported F: drivers/acpi/*thermal* ACPI VIDEO DRIVER -P: Zhang Rui -M: rui.zhang@intel.com +M: Zhang Rui L: linux-acpi@vger.kernel.org W: http://www.lesswatts.org/projects/acpi/ S: Supported F: drivers/acpi/video.c ACPI WMI DRIVER -P: Carlos Corbacho -M: carlos@strangeworlds.co.uk +M: Carlos Corbacho L: linux-acpi@vger.kernel.org W: http://www.lesswatts.org/projects/acpi/ S: Maintained F: drivers/platform/x86/wmi.c AD1889 ALSA SOUND DRIVER -P: Kyle McMartin -M: kyle@mcmartin.ca -P: Thibaut Varene -M: T-Bone@parisc-linux.org +M: Kyle McMartin +M: Thibaut Varene W: http://wiki.parisc-linux.org/AD1889 L: linux-parisc@vger.kernel.org S: Maintained F: sound/pci/ad1889.* ADM1025 HARDWARE MONITOR DRIVER -P: Jean Delvare -M: khali@linux-fr.org +M: Jean Delvare L: lm-sensors@lm-sensors.org S: Maintained F: Documentation/hwmon/adm1025 F: drivers/hwmon/adm1025.c ADM1029 HARDWARE MONITOR DRIVER -P: Corentin Labbe -M: corentin.labbe@geomatys.fr +M: Corentin Labbe L: lm-sensors@lm-sensors.org S: Maintained F: drivers/hwmon/adm1029.c ADM8211 WIRELESS DRIVER -P: Michael Wu -M: flamingice@sourmilk.net +M: Michael Wu L: linux-wireless@vger.kernel.org W: http://linuxwireless.org/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/mwu/mac80211-drivers.git @@ -347,35 +314,30 @@ S: Maintained F: drivers/net/wireless/adm8211.* ADT746X FAN DRIVER -P: Colin Leroy -M: colin@colino.net +M: Colin Leroy S: Maintained F: drivers/macintosh/therm_adt746x.c ADVANSYS SCSI DRIVER -P: Matthew Wilcox -M: matthew@wil.cx +M: Matthew Wilcox L: linux-scsi@vger.kernel.org S: Maintained F: Documentation/scsi/advansys.txt F: drivers/scsi/advansys.c AEDSP16 DRIVER -P: Riccardo Facchetti -M: fizban@tin.it +M: Riccardo Facchetti S: Maintained F: sound/oss/aedsp16.c AFFS FILE SYSTEM -P: Roman Zippel -M: zippel@linux-m68k.org +M: Roman Zippel S: Maintained F: Documentation/filesystems/affs.txt F: fs/affs/ AFS FILESYSTEM & AF_RXRPC SOCKET DOMAIN -P: David Howells -M: dhowells@redhat.com +M: David Howells L: linux-afs@lists.infradead.org S: Supported F: fs/afs/ @@ -383,40 +345,35 @@ F: include/net/af_rxrpc.h F: net/rxrpc/af_rxrpc.c AGPGART DRIVER -P: David Airlie -M: airlied@linux.ie +M: David Airlie T: git git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6.git S: Maintained F: drivers/char/agp/ F: include/linux/agp* AHA152X SCSI DRIVER -P: Juergen E. Fischer -M: fischer@norbit.de +M: "Juergen E. Fischer" L: linux-scsi@vger.kernel.org S: Maintained F: drivers/scsi/aha152x* F: drivers/scsi/pcmcia/aha152x* AIC7XXX / AIC79XX SCSI DRIVER -P: Hannes Reinecke -M: hare@suse.de +M: Hannes Reinecke L: linux-scsi@vger.kernel.org S: Maintained F: drivers/scsi/aic7xxx/ F: drivers/scsi/aic7xxx_old/ AIO -P: Benjamin LaHaise -M: bcrl@kvack.org +M: Benjamin LaHaise L: linux-aio@kvack.org S: Supported F: fs/aio.c F: include/linux/*aio*.h ALCATEL SPEEDTOUCH USB DRIVER -P: Duncan Sands -M: duncan.sands@free.fr +M: Duncan Sands L: linux-usb@vger.kernel.org W: http://www.linux-usb.org/SpeedTouch/ S: Maintained @@ -424,32 +381,27 @@ F: drivers/usb/atm/speedtch.c F: drivers/usb/atm/usbatm.c ALCHEMY AU1XX0 MMC DRIVER -P: Manuel Lauss -M: manuel.lauss@gmail.com +M: Manuel Lauss S: Maintained F: drivers/mmc/host/au1xmmc.c ALI1563 I2C DRIVER -P: Rudolf Marek -M: r.marek@assembler.cz +M: Rudolf Marek L: linux-i2c@vger.kernel.org S: Maintained F: Documentation/i2c/busses/i2c-ali1563 F: drivers/i2c/busses/i2c-ali1563.c ALPHA PORT -P: Richard Henderson -M: rth@twiddle.net +M: Richard Henderson S: Odd Fixes for 2.4; Maintained for 2.6. -P: Ivan Kokshaysky -M: ink@jurassic.park.msu.ru +M: Ivan Kokshaysky S: Maintained for 2.4; PCI support for 2.6. L: linux-alpha@vger.kernel.org F: arch/alpha/ AMD GEODE CS5536 USB DEVICE CONTROLLER DRIVER -P: Thomas Dahlmann -M: dahlmann.thomas@arcor.de +M: Thomas Dahlmann L: linux-geode@lists.infradead.org (moderated for non-subscribers) S: Supported F: drivers/usb/gadget/amd5536udc.* @@ -466,8 +418,7 @@ F: drivers/video/geode/ F: arch/x86/include/asm/geode.h AMD IOMMU (AMD-VI) -P: Joerg Roedel -M: joerg.roedel@amd.com +M: Joerg Roedel L: iommu@lists.linux-foundation.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/joro/linux-2.6-iommu.git S: Supported @@ -475,40 +426,33 @@ F: arch/x86/kernel/amd_iommu*.c F: arch/x86/include/asm/amd_iommu*.h AMD MICROCODE UPDATE SUPPORT -P: Andreas Herrmann -M: andreas.herrmann3@amd.com +M: Andreas Herrmann L: amd64-microcode@amd64.org S: Supported F: arch/x86/kernel/microcode_amd.c AMS (Apple Motion Sensor) DRIVER -P: Stelian Pop -M: stelian@popies.net -P: Michael Hanselmann -M: linux-kernel@hansmi.ch +M: Stelian Pop +M: Michael Hanselmann S: Supported F: drivers/hwmon/ams/ AMSO1100 RNIC DRIVER -P: Tom Tucker -M: tom@opengridcomputing.com -P: Steve Wise -M: swise@opengridcomputing.com +M: Tom Tucker +M: Steve Wise L: general@lists.openfabrics.org S: Maintained F: drivers/infiniband/hw/amso1100/ AOA (Apple Onboard Audio) ALSA DRIVER -P: Johannes Berg -M: johannes@sipsolutions.net +M: Johannes Berg L: linuxppc-dev@ozlabs.org L: alsa-devel@alsa-project.org (moderated for non-subscribers) S: Maintained F: sound/aoa/ APM DRIVER -P: Stephen Rothwell -M: sfr@canb.auug.org.au +M: Stephen Rothwell L: linux-laptop@vger.kernel.org W: http://www.canb.auug.org.au/~sfr/ S: Supported @@ -516,51 +460,44 @@ F: arch/x86/kernel/apm_32.c F: include/linux/apm_bios.h APPLE BCM5974 MULTITOUCH DRIVER -P: Henrik Rydberg -M: rydberg@euromail.se +M: Henrik Rydberg L: linux-input@vger.kernel.org S: Maintained F: drivers/input/mouse/bcm5974.c APPLE SMC DRIVER -P: Nicolas Boichat -M: nicolas@boichat.ch +M: Nicolas Boichat L: mactel-linux-devel@lists.sourceforge.net S: Maintained F: drivers/hwmon/applesmc.c APPLETALK NETWORK LAYER -P: Arnaldo Carvalho de Melo -M: acme@ghostprotocols.net +M: Arnaldo Carvalho de Melo S: Maintained F: drivers/net/appletalk/ F: net/appletalk/ APPLETOUCH TOUCHPAD DRIVER -P: Johannes Berg -M: johannes@sipsolutions.net +M: Johannes Berg L: linux-input@vger.kernel.org S: Maintained F: Documentation/input/appletouch.txt F: drivers/input/mouse/appletouch.c ARC FRAMEBUFFER DRIVER -P: Jaya Kumar -M: jayalk@intworks.biz +M: Jaya Kumar S: Maintained F: drivers/video/arcfb.c F: drivers/video/fb_defio.c ARM MFM AND FLOPPY DRIVERS -P: Ian Molton -M: spyro@f2s.com +M: Ian Molton S: Maintained F: arch/arm/lib/floppydma.S F: arch/arm/include/asm/floppy.h ARM PORT -P: Russell King -M: linux@arm.linux.org.uk +M: Russell King L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) W: http://www.arm.linux.org.uk/ S: Maintained @@ -571,79 +508,67 @@ S: Orphan F: drivers/mmc/host/mmci.* ARM/ADI ROADRUNNER MACHINE SUPPORT -P: Lennert Buytenhek -M: kernel@wantstofly.org +M: Lennert Buytenhek L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained F: arch/arm/mach-ixp23xx/ F: arch/arm/mach-ixp23xx/include/mach/ ARM/ADS SPHERE MACHINE SUPPORT -P: Lennert Buytenhek -M: kernel@wantstofly.org +M: Lennert Buytenhek L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained ARM/AFEB9260 MACHINE SUPPORT -P: Sergey Lapin -M: slapin@ossfans.org +M: Sergey Lapin L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained ARM/AJECO 1ARM MACHINE SUPPORT -P: Lennert Buytenhek -M: kernel@wantstofly.org +M: Lennert Buytenhek L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained ARM/ATMEL AT91RM9200 ARM ARCHITECTURE -P: Andrew Victor -M: linux@maxim.org.za +M: Andrew Victor L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) W: http://maxim.org.za/at91_26.html S: Maintained ARM/CIRRUS LOGIC EP93XX ARM ARCHITECTURE -P: Lennert Buytenhek -M: kernel@wantstofly.org +M: Lennert Buytenhek L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained ARM/CIRRUS LOGIC EDB9315A MACHINE SUPPORT -P: Lennert Buytenhek -M: kernel@wantstofly.org +M: Lennert Buytenhek L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained ARM/CLKDEV SUPPORT -P: Russell King -M: linux@arm.linux.org.uk +M: Russell King L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) F: arch/arm/common/clkdev.c F: arch/arm/include/asm/clkdev.h ARM/COMPULAB CM-X270/EM-X270 and CM-X300 MACHINE SUPPORT -P: Mike Rapoport -M: mike@compulab.co.il +M: Mike Rapoport L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained ARM/CORGI MACHINE SUPPORT -P: Richard Purdie -M: rpurdie@rpsys.net +M: Richard Purdie S: Maintained ARM/CORTINA SYSTEMS GEMINI ARM ARCHITECTURE -P: Paulius Zaleckas -M: paulius.zaleckas@teltonika.lt +M: Paulius Zaleckas L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) T: git git://gitorious.org/linux-gemini/mainline.git S: Maintained F: arch/arm/mach-gemini/ ARM/EBSA110 MACHINE SUPPORT -P: Russell King -M: linux@arm.linux.org.uk +M: Russell King L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) W: http://www.arm.linux.org.uk/ S: Maintained @@ -651,12 +576,9 @@ F: arch/arm/mach-ebsa110/ F: drivers/net/arm/am79c961a.* ARM/EZX SMARTPHONES (A780, A910, A1200, E680, ROKR E2 and ROKR E6) -P: Daniel Ribeiro -M: drwyrm@gmail.com -P: Stefan Schmidt -M: stefan@openezx.org -P: Harald Welte -M: laforge@openezx.org +M: Daniel Ribeiro +M: Stefan Schmidt +M: Harald Welte L: openezx-devel@lists.openezx.org (subscribers-only) W: http://www.openezx.org/ S: Maintained @@ -664,15 +586,13 @@ T: topgit git://git.openezx.org/openezx.git F: arch/arm/mach-pxa/ezx.c ARM/FARADAY FA526 PORT -P: Paulius Zaleckas -M: paulius.zaleckas@teltonika.lt +M: Paulius Zaleckas L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained F: arch/arm/mm/*-fa* ARM/FOOTBRIDGE ARCHITECTURE -P: Russell King -M: linux@arm.linux.org.uk +M: Russell King L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) W: http://www.arm.linux.org.uk/ S: Maintained @@ -680,175 +600,143 @@ F: arch/arm/include/asm/hardware/dec21285.h F: arch/arm/mach-footbridge/ ARM/FREESCALE IMX / MXC ARM ARCHITECTURE -P: Sascha Hauer -M: kernel@pengutronix.de +M: Sascha Hauer L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained ARM/GLOMATION GESBC9312SX MACHINE SUPPORT -P: Lennert Buytenhek -M: kernel@wantstofly.org +M: Lennert Buytenhek L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained ARM/GUMSTIX MACHINE SUPPORT -P: Steve Sakoman -M: sakoman@gmail.com +M: Steve Sakoman L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained ARM/H4700 (HP IPAQ HX4700) MACHINE SUPPORT -P: Philipp Zabel -M: philipp.zabel@gmail.com +M: Philipp Zabel S: Maintained F: arch/arm/mach-pxa/hx4700.c F: arch/arm/mach-pxa/include/mach/hx4700.h ARM/HP JORNADA 7XX MACHINE SUPPORT -P: Kristoffer Ericson -M: kristoffer.ericson@gmail.com +M: Kristoffer Ericson W: www.jlime.com S: Maintained ARM/INTEL IOP32X ARM ARCHITECTURE -P: Lennert Buytenhek -M: kernel@wantstofly.org -P: Dan Williams -M: dan.j.williams@intel.com +M: Lennert Buytenhek +M: Dan Williams L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Supported ARM/INTEL IOP33X ARM ARCHITECTURE -P: Dan Williams -M: dan.j.williams@intel.com +M: Dan Williams L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Supported ARM/INTEL IOP13XX ARM ARCHITECTURE -P: Lennert Buytenhek -M: kernel@wantstofly.org -P: Dan Williams -M: dan.j.williams@intel.com +M: Lennert Buytenhek +M: Dan Williams L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Supported ARM/INTEL IQ81342EX MACHINE SUPPORT -P: Lennert Buytenhek -M: kernel@wantstofly.org -P: Dan Williams -M: dan.j.williams@intel.com +M: Lennert Buytenhek +M: Dan Williams L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Supported ARM/INTEL IXP2000 ARM ARCHITECTURE -P: Lennert Buytenhek -M: kernel@wantstofly.org +M: Lennert Buytenhek L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained ARM/INTEL IXDP2850 MACHINE SUPPORT -P: Lennert Buytenhek -M: kernel@wantstofly.org +M: Lennert Buytenhek L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained ARM/INTEL IXP23XX ARM ARCHITECTURE -P: Lennert Buytenhek -M: kernel@wantstofly.org +M: Lennert Buytenhek L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained ARM/INTEL XSC3 (MANZANO) ARM CORE -P: Lennert Buytenhek -M: kernel@wantstofly.org -P: Dan Williams -M: dan.j.williams@intel.com +M: Lennert Buytenhek +M: Dan Williams L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Supported ARM/IP FABRICS DOUBLE ESPRESSO MACHINE SUPPORT -P: Lennert Buytenhek -M: kernel@wantstofly.org +M: Lennert Buytenhek L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained ARM/LOGICPD PXA270 MACHINE SUPPORT -P: Lennert Buytenhek -M: kernel@wantstofly.org +M: Lennert Buytenhek L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained ARM/MAGICIAN MACHINE SUPPORT -P: Philipp Zabel -M: philipp.zabel@gmail.com +M: Philipp Zabel S: Maintained ARM/MIOA701 MACHINE SUPPORT -P: Robert Jarzmik -M: robert.jarzmik@free.fr +M: Robert Jarzmik L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) F: arch/arm/mach-pxa/mioa701.c S: Maintained ARM/NEC MOBILEPRO 900/c MACHINE SUPPORT -P: Michael Petchkovsky -M: mkpetch@internode.on.net +M: Michael Petchkovsky S: Maintained ARM/OPENMOKO NEO FREERUNNER (GTA02) MACHINE SUPPORT -P: Nelson Castillo -M: arhuaco@freaks-unidos.net +M: Nelson Castillo L: openmoko-kernel@lists.openmoko.org (subscribers-only) W: http://wiki.openmoko.org/wiki/Neo_FreeRunner S: Supported ARM/TOSA MACHINE SUPPORT -P: Dmitry Eremin-Solenikov -M: dbaryshkov@gmail.com -P: Dirk Opfer -M: dirk@opfer-online.de +M: Dmitry Eremin-Solenikov +M: Dirk Opfer S: Maintained ARM/PALMTX,PALMT5,PALMLD,PALMTE2 SUPPORT -P: Marek Vasut -M: marek.vasut@gmail.com +M: Marek Vasut W: http://hackndev.com S: Maintained ARM/PALM TREO 680 SUPPORT -P: Tomas Cech -M: sleep_walker@suse.cz +M: Tomas Cech W: http://hackndev.com S: Maintained ARM/PALMZ72 SUPPORT -P: Sergey Lapin -M: slapin@ossfans.org +M: Sergey Lapin W: http://hackndev.com S: Maintained ARM/PLEB SUPPORT -P: Peter Chubb -M: pleb@gelato.unsw.edu.au +M: Peter Chubb W: http://www.disy.cse.unsw.edu.au/Hardware/PLEB S: Maintained ARM/PT DIGITAL BOARD PORT -P: Stefan Eletzhofer -M: stefan.eletzhofer@eletztrick.de +M: Stefan Eletzhofer L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) W: http://www.arm.linux.org.uk/ S: Maintained ARM/RADISYS ENP2611 MACHINE SUPPORT -P: Lennert Buytenhek -M: kernel@wantstofly.org +M: Lennert Buytenhek L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained ARM/RISCPC ARCHITECTURE -P: Russell King -M: linux@arm.linux.org.uk +M: Russell King L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) W: http://www.arm.linux.org.uk/ S: Maintained @@ -862,14 +750,12 @@ F: drivers/net/arm/ether* F: drivers/scsi/arm/ ARM/SHARK MACHINE SUPPORT -P: Alexander Schulz -M: alex@shark-linux.de +M: Alexander Schulz W: http://www.shark-linux.de/shark.html S: Maintained ARM/SAMSUNG ARM ARCHITECTURES -P: Ben Dooks -M: ben-linux@fluff.org +M: Ben Dooks L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) W: http://www.fluff.org/ben/linux/ S: Maintained @@ -877,85 +763,73 @@ F: arch/arm/plat-s3c/ F: arch/arm/plat-s3c24xx/ ARM/S3C2410 ARM ARCHITECTURE -P: Ben Dooks -M: ben-linux@fluff.org +M: Ben Dooks L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) W: http://www.fluff.org/ben/linux/ S: Maintained F: arch/arm/mach-s3c2410/ ARM/S3C2440 ARM ARCHITECTURE -P: Ben Dooks -M: ben-linux@fluff.org +M: Ben Dooks L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) W: http://www.fluff.org/ben/linux/ S: Maintained F: arch/arm/mach-s3c2440/ ARM/S3C2442 ARM ARCHITECTURE -P: Ben Dooks -M: ben-linux@fluff.org +M: Ben Dooks L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) W: http://www.fluff.org/ben/linux/ S: Maintained F: arch/arm/mach-s3c2442/ ARM/S3C2443 ARM ARCHITECTURE -P: Ben Dooks -M: ben-linux@fluff.org +M: Ben Dooks L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) W: http://www.fluff.org/ben/linux/ S: Maintained F: arch/arm/mach-s3c2443/ ARM/S3C6400 ARM ARCHITECTURE -P: Ben Dooks -M: ben-linux@fluff.org +M: Ben Dooks L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) W: http://www.fluff.org/ben/linux/ S: Maintained F: arch/arm/mach-s3c6400/ ARM/S3C6410 ARM ARCHITECTURE -P: Ben Dooks -M: ben-linux@fluff.org +M: Ben Dooks L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) W: http://www.fluff.org/ben/linux/ S: Maintained F: arch/arm/mach-s3c6410/ ARM/TECHNOLOGIC SYSTEMS TS7250 MACHINE SUPPORT -P: Lennert Buytenhek -M: kernel@wantstofly.org +M: Lennert Buytenhek L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained ARM/THECUS N2100 MACHINE SUPPORT -P: Lennert Buytenhek -M: kernel@wantstofly.org +M: Lennert Buytenhek L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained ARM/NUVOTON W90X900 ARM ARCHITECTURE -P: Wan ZongShun -M: mcuos.com@gmail.com +M: Wan ZongShun L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) W: http://www.mcuos.com S: Maintained ARM/VFP SUPPORT -P: Russell King -M: linux@arm.linux.org.uk +M: Russell King L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) W: http://www.arm.linux.org.uk/ S: Maintained F: arch/arm/vfp/ ASUS ACPI EXTRAS DRIVER -P: Corentin Chary -M: corentincj@iksaif.net -P: Karol Kozimor -M: sziwan@users.sourceforge.net +M: Corentin Chary +M: Karol Kozimor L: acpi4asus-user@lists.sourceforge.net W: http://acpi4asus.sf.net S: Maintained @@ -963,25 +837,21 @@ F: arch/x86/kernel/acpi/boot.c F: drivers/platform/x86/asus_acpi.c ASUS ASB100 HARDWARE MONITOR DRIVER -P: Mark M. Hoffman -M: mhoffman@lightlink.com +M: "Mark M. Hoffman" L: lm-sensors@lm-sensors.org S: Maintained F: drivers/hwmon/asb100.c ASUS LAPTOP EXTRAS DRIVER -P: Corentin Chary -M: corentincj@iksaif.net +M: Corentin Chary L: acpi4asus-user@lists.sourceforge.net W: http://acpi4asus.sf.net S: Maintained F: drivers/platform/x86/asus-laptop.c ASYNCHRONOUS TRANSFERS/TRANSFORMS (IOAT) API -P: Dan Williams -M: dan.j.williams@intel.com -P: Maciej Sosnowski -M: maciej.sosnowski@intel.com +M: Dan Williams +M: Maciej Sosnowski W: http://sourceforge.net/projects/xscaleiop S: Supported F: Documentation/crypto/async-tx-api.txt @@ -991,64 +861,49 @@ F: include/linux/dmaengine.h F: include/linux/async_tx.h ATA OVER ETHERNET (AOE) DRIVER -P: Ed L. Cashin -M: ecashin@coraid.com +M: "Ed L. Cashin" W: http://www.coraid.com/support/linux S: Supported F: Documentation/aoe/ F: drivers/block/aoe/ ATHEROS ATH5K WIRELESS DRIVER -P: Jiri Slaby -M: jirislaby@gmail.com -P: Nick Kossifidis -M: mickflemm@gmail.com -P: Luis R. Rodriguez -M: lrodriguez@atheros.com -P: Bob Copeland -M: me@bobcopeland.com +M: Jiri Slaby +M: Nick Kossifidis +M: "Luis R. Rodriguez" +M: Bob Copeland L: linux-wireless@vger.kernel.org L: ath5k-devel@lists.ath5k.org S: Maintained F: drivers/net/wireless/ath/ath5k/ ATHEROS ATH9K WIRELESS DRIVER -P: Luis R. Rodriguez -M: lrodriguez@atheros.com -P: Jouni Malinen -M: jmalinen@atheros.com -P: Sujith Manoharan -M: Sujith.Manoharan@atheros.com -P: Vasanthakumar Thiagarajan -M: vasanth@atheros.com -P: Senthil Balasubramanian -M: senthilkumar@atheros.com +M: "Luis R. Rodriguez" +M: Jouni Malinen +M: Sujith Manoharan +M: Vasanthakumar Thiagarajan +M: Senthil Balasubramanian L: linux-wireless@vger.kernel.org L: ath9k-devel@lists.ath9k.org S: Supported F: drivers/net/wireless/ath/ath9k/ ATHEROS AR9170 WIRELESS DRIVER -P: Christian Lamparter -M: chunkeey@web.de +M: Christian Lamparter L: linux-wireless@vger.kernel.org W: http://wireless.kernel.org/en/users/Drivers/ar9170 S: Maintained F: drivers/net/wireless/ath/ar9170/ ATI_REMOTE2 DRIVER -P: Ville Syrjala -M: syrjala@sci.fi +M: Ville Syrjala S: Maintained F: drivers/input/misc/ati_remote2.c ATLX ETHERNET DRIVERS -P: Jay Cliburn -M: jcliburn@gmail.com -P: Chris Snook -M: csnook@redhat.com -P: Jie Yang -M: jie.yang@atheros.com +M: Jay Cliburn +M: Chris Snook +M: Jie Yang L: atl1-devel@lists.sourceforge.net W: http://sourceforge.net/projects/atl1 W: http://atl1.sourceforge.net @@ -1056,8 +911,7 @@ S: Maintained F: drivers/net/atlx/ ATM -P: Chas Williams -M: chas@cmf.nrl.navy.mil +M: Chas Williams L: linux-atm-general@lists.sourceforge.net (subscribers-only) L: netdev@vger.kernel.org W: http://linux-atm.sourceforge.net @@ -1066,8 +920,7 @@ F: drivers/atm/ F: include/linux/atm* ATMEL AT91 MCI DRIVER -P: Nicolas Ferre -M: nicolas.ferre@atmel.com +M: Nicolas Ferre L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) W: http://www.atmel.com/products/AT91/ W: http://www.at91.com/ @@ -1075,49 +928,42 @@ S: Maintained F: drivers/mmc/host/at91_mci.c ATMEL AT91 / AT32 MCI DRIVER -P: Nicolas Ferre -M: nicolas.ferre@atmel.com +M: Nicolas Ferre S: Maintained F: drivers/mmc/host/atmel-mci.c F: drivers/mmc/host/atmel-mci-regs.h ATMEL AT91 / AT32 SERIAL DRIVER -P: Haavard Skinnemoen -M: hskinnemoen@atmel.com +M: Haavard Skinnemoen S: Supported F: drivers/serial/atmel_serial.c ATMEL LCDFB DRIVER -P: Nicolas Ferre -M: nicolas.ferre@atmel.com +M: Nicolas Ferre L: linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers) S: Maintained F: drivers/video/atmel_lcdfb.c F: include/video/atmel_lcdc.h ATMEL MACB ETHERNET DRIVER -P: Haavard Skinnemoen -M: hskinnemoen@atmel.com +M: Haavard Skinnemoen S: Supported F: drivers/net/macb.* ATMEL SPI DRIVER -P: Haavard Skinnemoen -M: hskinnemoen@atmel.com +M: Haavard Skinnemoen S: Supported F: drivers/spi/atmel_spi.* ATMEL USBA UDC DRIVER -P: Haavard Skinnemoen -M: hskinnemoen@atmel.com +M: Haavard Skinnemoen L: kernel@avr32linux.org W: http://avr32linux.org/twiki/bin/view/Main/AtmelUsbDeviceDriver S: Supported F: drivers/usb/gadget/atmel_usba_udc.* ATMEL WIRELESS DRIVER -P: Simon Kelley -M: simon@thekelleys.org.uk +M: Simon Kelley L: linux-wireless@vger.kernel.org W: http://www.thekelleys.org.uk/atmel W: http://atmelwlandriver.sourceforge.net/ @@ -1125,10 +971,8 @@ S: Maintained F: drivers/net/wireless/atmel* AUDIT SUBSYSTEM -P: Al Viro -M: viro@zeniv.linux.org.uk -P: Eric Paris -M: eparis@redhat.com +M: Al Viro +M: Eric Paris L: linux-audit@redhat.com (subscribers-only) W: http://people.redhat.com/sgrubb/audit/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current.git @@ -1137,8 +981,7 @@ F: include/linux/audit.h F: kernel/audit* AUXILIARY DISPLAY DRIVERS -P: Miguel Ojeda Sandonis -M: miguel.ojeda.sandonis@gmail.com +M: Miguel Ojeda Sandonis W: http://miguelojeda.es/auxdisplay.htm W: http://jair.lab.fi.uva.es/~migojed/auxdisplay.htm S: Maintained @@ -1146,8 +989,7 @@ F: drivers/auxdisplay/ F: include/linux/cfag12864b.h AVR32 ARCHITECTURE -P: Haavard Skinnemoen -M: hskinnemoen@atmel.com +M: Haavard Skinnemoen W: http://www.atmel.com/products/AVR32/ W: http://avr32linux.org/ W: http://avrfreaks.net/ @@ -1155,14 +997,12 @@ S: Supported F: arch/avr32/ AVR32/AT32AP MACHINE SUPPORT -P: Haavard Skinnemoen -M: hskinnemoen@atmel.com +M: Haavard Skinnemoen S: Supported F: arch/avr32/mach-at32ap/ AX.25 NETWORK LAYER -P: Ralf Baechle -M: ralf@linux-mips.org +M: Ralf Baechle L: linux-hams@vger.kernel.org W: http://www.linux-ax25.org/ S: Maintained @@ -1171,128 +1011,110 @@ F: include/net/ax25.h F: net/ax25/ B43 WIRELESS DRIVER -P: Michael Buesch -M: mb@bu3sch.de -P: Stefano Brivio -M: stefano.brivio@polimi.it +M: Michael Buesch +M: Stefano Brivio L: linux-wireless@vger.kernel.org W: http://linuxwireless.org/en/users/Drivers/b43 S: Maintained F: drivers/net/wireless/b43/ B43LEGACY WIRELESS DRIVER -P: Larry Finger -M: Larry.Finger@lwfinger.net -P: Stefano Brivio -M: stefano.brivio@polimi.it +M: Larry Finger +M: Stefano Brivio L: linux-wireless@vger.kernel.org W: http://linuxwireless.org/en/users/Drivers/b43 S: Maintained F: drivers/net/wireless/b43legacy/ BACKLIGHT CLASS/SUBSYSTEM -P: Richard Purdie -M: rpurdie@rpsys.net +M: Richard Purdie S: Maintained F: drivers/video/backlight/ F: include/linux/backlight.h BAYCOM/HDLCDRV DRIVERS FOR AX.25 -P: Thomas Sailer -M: t.sailer@alumni.ethz.ch +M: Thomas Sailer L: linux-hams@vger.kernel.org W: http://www.baycom.org/~tom/ham/ham.html S: Maintained F: drivers/net/hamradio/baycom* BEFS FILE SYSTEM -P: Sergey S. Kostyliov -M: rathamahata@php4.ru +M: "Sergey S. Kostyliov" S: Maintained F: Documentation/filesystems/befs.txt F: fs/befs/ BFS FILE SYSTEM -P: Tigran A. Aivazian -M: tigran@aivazian.fsnet.co.uk +M: "Tigran A. Aivazian" S: Maintained F: Documentation/filesystems/bfs.txt F: fs/bfs/ F: include/linux/bfs_fs.h BLACKFIN ARCHITECTURE -P: Mike Frysinger -M: vapier@gentoo.org +M: Mike Frysinger L: uclinux-dist-devel@blackfin.uclinux.org W: http://blackfin.uclinux.org S: Supported F: arch/blackfin/ BLACKFIN EMAC DRIVER -P: Michael Hennerich -M: michael.hennerich@analog.com +M: Michael Hennerich L: uclinux-dist-devel@blackfin.uclinux.org W: http://blackfin.uclinux.org S: Supported F: drivers/net/bfin_mac.* BLACKFIN RTC DRIVER -P: Mike Frysinger -M: vapier.adi@gmail.com +M: Mike Frysinger L: uclinux-dist-devel@blackfin.uclinux.org W: http://blackfin.uclinux.org S: Supported F: drivers/rtc/rtc-bfin.c BLACKFIN SERIAL DRIVER -P: Sonic Zhang -M: sonic.zhang@analog.com +M: Sonic Zhang L: uclinux-dist-devel@blackfin.uclinux.org W: http://blackfin.uclinux.org S: Supported F: drivers/serial/bfin_5xx.c BLACKFIN WATCHDOG DRIVER -P: Mike Frysinger -M: vapier.adi@gmail.com +M: Mike Frysinger L: uclinux-dist-devel@blackfin.uclinux.org W: http://blackfin.uclinux.org S: Supported F: drivers/watchdog/bfin_wdt.c BLACKFIN I2C TWI DRIVER -P: Sonic Zhang -M: sonic.zhang@analog.com +M: Sonic Zhang L: uclinux-dist-devel@blackfin.uclinux.org W: http://blackfin.uclinux.org/ S: Supported F: drivers/i2c/busses/i2c-bfin-twi.c BLOCK LAYER -P: Jens Axboe -M: axboe@kernel.dk +M: Jens Axboe T: git git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux-2.6-block.git S: Maintained F: block/ BLOCK2MTD DRIVER -P: Joern Engel -M: joern@lazybastard.org +M: Joern Engel L: linux-mtd@lists.infradead.org S: Maintained F: drivers/mtd/devices/block2mtd.c BLUETOOTH DRIVERS -P: Marcel Holtmann -M: marcel@holtmann.org +M: Marcel Holtmann L: linux-bluetooth@vger.kernel.org W: http://www.bluez.org/ S: Maintained F: drivers/bluetooth/ BLUETOOTH SUBSYSTEM -P: Marcel Holtmann -M: marcel@holtmann.org +M: Marcel Holtmann L: linux-bluetooth@vger.kernel.org W: http://www.bluez.org/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/holtmann/bluetooth-2.6.git @@ -1301,8 +1123,7 @@ F: net/bluetooth/ F: include/net/bluetooth/ BONDING DRIVER -P: Jay Vosburgh -M: fubar@us.ibm.com +M: Jay Vosburgh L: bonding-devel@lists.sourceforge.net W: http://sourceforge.net/projects/bonding/ S: Supported @@ -1310,54 +1131,46 @@ F: drivers/net/bonding/ F: include/linux/if_bonding.h BROADCOM B44 10/100 ETHERNET DRIVER -P: Gary Zambrano -M: zambrano@broadcom.com +M: Gary Zambrano L: netdev@vger.kernel.org S: Supported F: drivers/net/b44.* BROADCOM BNX2 GIGABIT ETHERNET DRIVER -P: Michael Chan -M: mchan@broadcom.com +M: Michael Chan L: netdev@vger.kernel.org S: Supported F: drivers/net/bnx2.* F: drivers/net/bnx2_* BROADCOM BNX2X 10 GIGABIT ETHERNET DRIVER -P: Eilon Greenstein -M: eilong@broadcom.com +M: Eilon Greenstein L: netdev@vger.kernel.org S: Supported F: drivers/net/bnx2x* BROADCOM TG3 GIGABIT ETHERNET DRIVER -P: Matt Carlson -M: mcarlson@broadcom.com -P: Michael Chan -M: mchan@broadcom.com +M: Matt Carlson +M: Michael Chan L: netdev@vger.kernel.org S: Supported F: drivers/net/tg3.* BSG (block layer generic sg v4 driver) -P: FUJITA Tomonori -M: fujita.tomonori@lab.ntt.co.jp +M: FUJITA Tomonori L: linux-scsi@vger.kernel.org S: Supported F: block/bsg.c F: include/linux/bsg.h BT8XXGPIO DRIVER -P: Michael Buesch -M: mb@bu3sch.de +M: Michael Buesch W: http://bu3sch.de/btgpio.php S: Maintained F: drivers/gpio/bt8xxgpio.c BTRFS FILE SYSTEM -P: Chris Mason -M: chris.mason@oracle.com +M: Chris Mason L: linux-btrfs@vger.kernel.org W: http://btrfs.wiki.kernel.org/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable.git @@ -1366,8 +1179,7 @@ F: Documentation/filesystems/btrfs.txt F: fs/btrfs/ BTTV VIDEO4LINUX DRIVER -P: Mauro Carvalho Chehab -M: mchehab@infradead.org +M: Mauro Carvalho Chehab L: linux-media@vger.kernel.org W: http://linuxtv.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git @@ -1376,16 +1188,14 @@ F: Documentation/video4linux/bttv/ F: drivers/media/video/bt8xx/bttv* CACHEFILES: FS-CACHE BACKEND FOR CACHING ON MOUNTED FILESYSTEMS -P: David Howells -M: dhowells@redhat.com +M: David Howells L: linux-cachefs@redhat.com S: Supported F: Documentation/filesystems/caching/cachefiles.txt F: fs/cachefiles/ CAFE CMOS INTEGRATED CAMERA CONTROLLER DRIVER -P: Jonathan Corbet -M: corbet@lwn.net +M: Jonathan Corbet L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git S: Maintained @@ -1393,10 +1203,8 @@ F: Documentation/video4linux/cafe_ccic F: drivers/media/video/cafe_ccic* CALGARY x86-64 IOMMU -P: Muli Ben-Yehuda -M: muli@il.ibm.com -P: Jon D. Mason -M: jdmason@kudzu.us +M: Muli Ben-Yehuda +M: "Jon D. Mason" L: discuss@x86-64.org S: Maintained F: arch/x86/kernel/pci-calgary_64.c @@ -1405,10 +1213,8 @@ F: arch/x86/include/asm/calgary.h F: arch/x86/include/asm/tce.h CAN NETWORK LAYER -P: Urs Thuermann -M: urs.thuermann@volkswagen.de -P: Oliver Hartkopp -M: oliver.hartkopp@volkswagen.de +M: Urs Thuermann +M: Oliver Hartkopp L: socketcan-core@lists.berlios.de (subscribers-only) W: http://developer.berlios.de/projects/socketcan/ S: Maintained @@ -1417,15 +1223,13 @@ F: include/linux/can/ F: include/linux/can.h CAN NETWORK DRIVERS -P: Wolfgang Grandegger -M: wg@grandegger.com +M: Wolfgang Grandegger L: socketcan-core@lists.berlios.de (subscribers-only) W: http://developer.berlios.de/projects/socketcan/ S: Maintained CELL BROADBAND ENGINE ARCHITECTURE -P: Arnd Bergmann -M: arnd@arndb.de +M: Arnd Bergmann L: linuxppc-dev@ozlabs.org L: cbe-oss-dev@ozlabs.org W: http://www.ibm.com/developerworks/power/cell/ @@ -1436,8 +1240,7 @@ F: arch/powerpc/oprofile/*cell* F: arch/powerpc/platforms/cell/ CERTIFIED WIRELESS USB (WUSB) SUBSYSTEM: -P: David Vrabel -M: david.vrabel@csr.com +M: David Vrabel L: linux-usb@vger.kernel.org S: Supported F: Documentation/usb/WUSB-Design-overview.txt @@ -1446,8 +1249,7 @@ F: drivers/usb/wusbcore/ F: include/linux/usb/wusb* CFAG12864B LCD DRIVER -P: Miguel Ojeda Sandonis -M: miguel.ojeda.sandonis@gmail.com +M: Miguel Ojeda Sandonis W: http://miguelojeda.es/auxdisplay.htm W: http://jair.lab.fi.uva.es/~migojed/auxdisplay.htm S: Maintained @@ -1455,8 +1257,7 @@ F: drivers/auxdisplay/cfag12864b.c F: include/linux/cfag12864b.h CFAG12864BFB LCD FRAMEBUFFER DRIVER -P: Miguel Ojeda Sandonis -M: miguel.ojeda.sandonis@gmail.com +M: Miguel Ojeda Sandonis W: http://miguelojeda.es/auxdisplay.htm W: http://jair.lab.fi.uva.es/~migojed/auxdisplay.htm S: Maintained @@ -1464,8 +1265,7 @@ F: drivers/auxdisplay/cfag12864bfb.c F: include/linux/cfag12864b.h CFG80211 and NL80211 -P: Johannes Berg -M: johannes@sipsolutions.net +M: Johannes Berg L: linux-wireless@vger.kernel.org S: Maintained F: include/linux/nl80211.h @@ -1474,57 +1274,47 @@ F: net/wireless/* X: net/wireless/wext* CHECKPATCH -P: Andy Whitcroft -M: apw@canonical.com +M: Andy Whitcroft S: Supported F: scripts/checkpatch.pl CISCO 10G ETHERNET DRIVER -P: Scott Feldman -M: scofeldm@cisco.com -P: Joe Eykholt -M: jeykholt@cisco.com +M: Scott Feldman +M: Joe Eykholt S: Supported F: drivers/net/enic/ CIRRUS LOGIC EP93XX ETHERNET DRIVER -P: Lennert Buytenhek -M: kernel@wantstofly.org +M: Lennert Buytenhek L: netdev@vger.kernel.org S: Maintained F: drivers/net/arm/ep93xx_eth.c CIRRUS LOGIC EP93XX OHCI USB HOST DRIVER -P: Lennert Buytenhek -M: kernel@wantstofly.org +M: Lennert Buytenhek L: linux-usb@vger.kernel.org S: Maintained F: drivers/usb/host/ohci-ep93xx.c CIRRUS LOGIC CS4270 SOUND DRIVER -P: Timur Tabi -M: timur@freescale.com +M: Timur Tabi L: alsa-devel@alsa-project.org (moderated for non-subscribers) S: Supported F: sound/soc/codecs/cs4270* CLK API -P: Russell King -M: linux@arm.linux.org.uk +M: Russell King F: include/linux/clk.h CISCO FCOE HBA DRIVER -P: Abhijeet Joglekar -M: abjoglek@cisco.com -P: Joe Eykholt -M: jeykholt@cisco.com +M: Abhijeet Joglekar +M: Joe Eykholt L: linux-scsi@vger.kernel.org S: Supported F: drivers/scsi/fnic/ CODA FILE SYSTEM -P: Jan Harkes -M: jaharkes@cs.cmu.edu +M: Jan Harkes M: coda@cs.cmu.edu L: codalist@coda.cs.cmu.edu W: http://www.coda.cs.cmu.edu/ @@ -1534,8 +1324,7 @@ F: fs/coda/ F: include/linux/coda*.h COMMON INTERNET FILE SYSTEM (CIFS) -P: Steve French -M: sfrench@samba.org +M: Steve French L: linux-cifs-client@lists.samba.org L: samba-technical@lists.samba.org W: http://linux-cifs.samba.org/ @@ -1545,67 +1334,57 @@ F: Documentation/filesystems/cifs.txt F: fs/cifs/ COMPACTPCI HOTPLUG CORE -P: Scott Murray -M: scott@spiteful.org +M: Scott Murray L: linux-pci@vger.kernel.org S: Maintained F: drivers/pci/hotplug/cpci_hotplug* COMPACTPCI HOTPLUG ZIATECH ZT5550 DRIVER -P: Scott Murray -M: scott@spiteful.org +M: Scott Murray L: linux-pci@vger.kernel.org S: Maintained F: drivers/pci/hotplug/cpcihp_zt5550.* COMPACTPCI HOTPLUG GENERIC DRIVER -P: Scott Murray -M: scott@spiteful.org +M: Scott Murray L: linux-pci@vger.kernel.org S: Maintained F: drivers/pci/hotplug/cpcihp_generic.c COMPAL LAPTOP SUPPORT -P: Cezary Jackiewicz -M: cezary.jackiewicz@gmail.com +M: Cezary Jackiewicz S: Maintained F: drivers/platform/x86/compal-laptop.c COMPUTONE INTELLIPORT MULTIPORT CARD -P: Michael H. Warfield -M: mhw@wittsend.com +M: "Michael H. Warfield" W: http://www.wittsend.com/computone.html S: Maintained F: Documentation/serial/computone.txt F: drivers/char/ip2/ CONEXANT ACCESSRUNNER USB DRIVER -P: Simon Arlott -M: cxacru@fire.lp0.eu +M: Simon Arlott L: accessrunner-general@lists.sourceforge.net W: http://accessrunner.sourceforge.net/ S: Maintained F: drivers/usb/atm/cxacru.c CONFIGFS -P: Joel Becker -M: joel.becker@oracle.com +M: Joel Becker S: Supported F: fs/configfs/ F: include/linux/configfs.h CONNECTOR -P: Evgeniy Polyakov -M: zbr@ioremap.net +M: Evgeniy Polyakov L: netdev@vger.kernel.org S: Maintained F: drivers/connector/ CONTROL GROUPS (CGROUPS) -P: Paul Menage -M: menage@google.com -P: Li Zefan -M: lizf@cn.fujitsu.com +M: Paul Menage +M: Li Zefan L: containers@lists.linux-foundation.org S: Maintained F: include/linux/cgroup* @@ -1613,30 +1392,26 @@ F: kernel/cgroup* F: mm/*cgroup* CORETEMP HARDWARE MONITORING DRIVER -P: Rudolf Marek -M: r.marek@assembler.cz +M: Rudolf Marek L: lm-sensors@lm-sensors.org S: Maintained F: Documentation/hwmon/coretemp F: drivers/hwmon/coretemp.c COSA/SRP SYNC SERIAL DRIVER -P: Jan "Yenya" Kasprzak -M: kas@fi.muni.cz +M: Jan "Yenya" Kasprzak W: http://www.fi.muni.cz/~kas/cosa/ S: Maintained F: drivers/net/wan/cosa* CPMAC ETHERNET DRIVER -P: Florian Fainelli -M: florian@openwrt.org +M: Florian Fainelli L: netdev@vger.kernel.org S: Maintained F: drivers/net/cpmac.c CPU FREQUENCY DRIVERS -P: Dave Jones -M: davej@redhat.com +M: Dave Jones L: cpufreq@vger.kernel.org W: http://www.codemonkey.org.uk/projects/cpufreq/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq.git @@ -1646,15 +1421,13 @@ F: drivers/cpufreq/ F: include/linux/cpufreq.h CPUID/MSR DRIVER -P: H. Peter Anvin -M: hpa@zytor.com +M: "H. Peter Anvin" S: Maintained F: arch/x86/kernel/cpuid.c F: arch/x86/kernel/msr.c CPUSETS -P: Paul Menage -M: menage@google.com +M: Paul Menage W: http://www.bullopensource.org/cpuset/ W: http://oss.sgi.com/projects/cpusets/ S: Supported @@ -1669,20 +1442,16 @@ F: Documentation/filesystems/cramfs.txt F: fs/cramfs/ CRIS PORT -P: Mikael Starvik -M: starvik@axis.com -P: Jesper Nilsson -M: jesper.nilsson@axis.com +M: Mikael Starvik +M: Jesper Nilsson L: linux-cris-kernel@axis.com W: http://developer.axis.com S: Maintained F: arch/cris/ CRYPTO API -P: Herbert Xu -M: herbert@gondor.apana.org.au -P: David S. Miller -M: davem@davemloft.net +M: Herbert Xu +M: "David S. Miller" L: linux-crypto@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6.git S: Maintained @@ -1693,22 +1462,18 @@ F: drivers/crypto/ F: include/crypto/ CRYPTOGRAPHIC RANDOM NUMBER GENERATOR -P: Neil Horman -M: nhorman@tuxdriver.com +M: Neil Horman L: linux-crypto@vger.kernel.org S: Maintained CS5535 Audio ALSA driver -P: Jaya Kumar -M: jayakumar.alsa@gmail.com +M: Jaya Kumar S: Maintained F: sound/pci/cs5535audio/ CX18 VIDEO4LINUX DRIVER -P: Hans Verkuil -M: hverkuil@xs4all.nl -P: Andy Walls -M: awalls@radix.net +M: Hans Verkuil +M: Andy Walls L: ivtv-devel@ivtvdriver.org L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git @@ -1719,32 +1484,28 @@ F: Documentation/video4linux/cx18.txt F: drivers/media/video/cx18/ CXGB3 ETHERNET DRIVER (CXGB3) -P: Divy Le Ray -M: divy@chelsio.com +M: Divy Le Ray L: netdev@vger.kernel.org W: http://www.chelsio.com S: Supported F: drivers/net/cxgb3/ CXGB3 IWARP RNIC DRIVER (IW_CXGB3) -P: Steve Wise -M: swise@chelsio.com +M: Steve Wise L: general@lists.openfabrics.org W: http://www.openfabrics.org S: Supported F: drivers/infiniband/hw/cxgb3/ CYBERPRO FB DRIVER -P: Russell King -M: linux@arm.linux.org.uk +M: Russell King L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) W: http://www.arm.linux.org.uk/ S: Maintained F: drivers/video/cyber2000fb.* CYCLADES 2X SYNC CARD DRIVER -P: Arnaldo Carvalho de Melo -M: acme@ghostprotocols.net +M: Arnaldo Carvalho de Melo W: http://oops.ghostprotocols.net:81/blog S: Maintained F: drivers/net/wan/cycx* @@ -1761,8 +1522,7 @@ S: Orphan F: drivers/net/wan/pc300* DAMA SLAVE for AX.25 -P: Joerg Reuter -M: jreuter@yaina.de +M: Joerg Reuter W: http://yaina.de/jreuter/ W: http://www.qsl.net/dl1bke/ L: linux-hams@vger.kernel.org @@ -1776,29 +1536,23 @@ F: net/ax25/ax25_timer.c F: net/ax25/sysctl_net_ax25.c DAVICOM FAST ETHERNET (DMFE) NETWORK DRIVER -P: Tobias Ringstrom -M: tori@unhappy.mine.nu +M: Tobias Ringstrom L: netdev@vger.kernel.org S: Maintained F: Documentation/networking/dmfe.txt F: drivers/net/tulip/dmfe.c DC390/AM53C974 SCSI driver -P: Kurt Garloff -M: garloff@suse.de +M: Kurt Garloff W: http://www.garloff.de/kurt/linux/dc390/ -P: Guennadi Liakhovetski -M: g.liakhovetski@gmx.de +M: Guennadi Liakhovetski S: Maintained F: drivers/scsi/tmscsim.* DC395x SCSI driver -P: Oliver Neukum -M: oliver@neukum.name -P: Ali Akcaagac -M: aliakc@web.de -P: Jamie Lenehan -M: lenehan@twibble.org +M: Oliver Neukum +M: Ali Akcaagac +M: Jamie Lenehan W: http://twibble.org/dist/dc395x/ L: dc395x@twibble.org L: http://lists.twibble.org/mailman/listinfo/dc395x/ @@ -1807,8 +1561,7 @@ F: Documentation/scsi/dc395x.txt F: drivers/scsi/dc395x.* DCCP PROTOCOL -P: Arnaldo Carvalho de Melo -M: acme@ghostprotocols.net +M: Arnaldo Carvalho de Melo L: dccp@vger.kernel.org W: http://linux-net.osdl.org/index.php/DCCP S: Maintained @@ -1817,8 +1570,7 @@ F: include/linux/tfrc.h F: net/dccp/ DECnet NETWORK LAYER -P: Christine Caulfield -M: christine.caulfield@googlemail.com +M: Christine Caulfield W: http://linux-decnet.sourceforge.net L: linux-decnet-user@lists.sourceforge.net S: Maintained @@ -1826,40 +1578,34 @@ F: Documentation/networking/decnet.txt F: net/decnet/ DEFXX FDDI NETWORK DRIVER -P: Maciej W. Rozycki -M: macro@linux-mips.org +M: "Maciej W. Rozycki" S: Maintained F: drivers/net/defxx.* DELL LAPTOP DRIVER -P: Matthew Garrett -M: mjg59@srcf.ucam.org +M: Matthew Garrett S: Maintained F: drivers/platform/x86/dell-laptop.c DELL LAPTOP SMM DRIVER -P: Massimo Dal Zotto -M: dz@debian.org +M: Massimo Dal Zotto W: http://www.debian.org/~dz/i8k/ S: Maintained F: drivers/char/i8k.c F: include/linux/i8k.h DELL SYSTEMS MANAGEMENT BASE DRIVER (dcdbas) -P: Doug Warzecha -M: Douglas_Warzecha@dell.com +M: Doug Warzecha S: Maintained F: Documentation/dcdbas.txt F: drivers/firmware/dcdbas.* DELL WMI EXTRAS DRIVER -P: Matthew Garrett -M: mjg59@srcf.ucam.org +M: Matthew Garrett S: Maintained DEVICE NUMBER REGISTRY -P: Torben Mathiasen -M: device@lanana.org +M: Torben Mathiasen W: http://lanana.org/docs/device-list/index.html S: Maintained @@ -1874,8 +1620,7 @@ F: include/linux/device-mapper.h F: include/linux/dm-*.h DIGI INTL. EPCA DRIVER -P: Digi International, Inc -M: Eng.Linux@digi.com +M: "Digi International, Inc" L: Eng.Linux@digi.com W: http://www.digi.com S: Orphan @@ -1884,34 +1629,29 @@ F: drivers/char/epca* F: drivers/char/digi* DIRECTORY NOTIFICATION (DNOTIFY) -P: Eric Paris -M: eparis@parisplace.org +M: Eric Paris S: Maintained F: Documentation/filesystems/dnotify.txt F: fs/notify/dnotify/ F: include/linux/dnotify.h DISK GEOMETRY AND PARTITION HANDLING -P: Andries Brouwer -M: aeb@cwi.nl +M: Andries Brouwer W: http://www.win.tue.nl/~aeb/linux/Large-Disk.html W: http://www.win.tue.nl/~aeb/linux/zip/zip-1.html W: http://www.win.tue.nl/~aeb/partitions/partition_types-1.html S: Maintained DISKQUOTA -P: Jan Kara -M: jack@suse.cz +M: Jan Kara S: Maintained F: Documentation/filesystems/quota.txt F: fs/quota/ F: include/linux/quota*.h DISTRIBUTED LOCK MANAGER (DLM) -P: Christine Caulfield -M: ccaulfie@redhat.com -P: David Teigland -M: teigland@redhat.com +M: Christine Caulfield +M: David Teigland L: cluster-devel@redhat.com W: http://sources.redhat.com/cluster/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm.git @@ -1919,52 +1659,44 @@ S: Supported F: fs/dlm/ DMA GENERIC OFFLOAD ENGINE SUBSYSTEM -P: Maciej Sosnowski -M: maciej.sosnowski@intel.com -P: Dan Williams -M: dan.j.williams@intel.com +M: Maciej Sosnowski +M: Dan Williams S: Supported F: drivers/dma/ F: include/linux/dma* DME1737 HARDWARE MONITOR DRIVER -P: Juerg Haefliger -M: juergh@gmail.com +M: Juerg Haefliger L: lm-sensors@lm-sensors.org S: Maintained F: Documentation/hwmon/dme1737 F: drivers/hwmon/dme1737.c DOCBOOK FOR DOCUMENTATION -P: Randy Dunlap -M: rdunlap@xenotime.net +M: Randy Dunlap S: Maintained DOCKING STATION DRIVER -P: Shaohua Li -M: shaohua.li@intel.com +M: Shaohua Li L: linux-acpi@vger.kernel.org S: Supported F: drivers/acpi/dock.c DOCUMENTATION -P: Randy Dunlap -M: rdunlap@xenotime.net +M: Randy Dunlap L: linux-doc@vger.kernel.org S: Maintained F: Documentation/ DOUBLETALK DRIVER -P: James R. Van Zandt -M: jrv@vanzandt.mv.com +M: "James R. Van Zandt" L: blinux-list@redhat.com S: Maintained F: drivers/char/dtlk.c F: include/linux/dtlk.h DPT_I2O SCSI RAID DRIVER -P: Adaptec OEM Raid Solutions -M: aacraid@adaptec.com +M: Adaptec OEM Raid Solutions L: linux-scsi@vger.kernel.org W: http://www.adaptec.com/ S: Maintained @@ -1972,8 +1704,7 @@ F: drivers/scsi/dpt* F: drivers/scsi/dpt/ DRIVER CORE, KOBJECTS, AND SYSFS -P: Greg Kroah-Hartman -M: gregkh@suse.de +M: Greg Kroah-Hartman T: quilt kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/ S: Supported F: Documentation/kobject.txt @@ -1983,52 +1714,45 @@ F: include/linux/kobj* F: lib/kobj* DRM DRIVERS -P: David Airlie -M: airlied@linux.ie +M: David Airlie L: dri-devel@lists.sourceforge.net T: git git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6.git S: Maintained F: drivers/gpu/drm/ DSCC4 DRIVER -P: Francois Romieu -M: romieu@fr.zoreil.com +M: Francois Romieu L: netdev@vger.kernel.org S: Maintained F: drivers/net/wan/dscc4.c DZ DECSTATION DZ11 SERIAL DRIVER -P: Maciej W. Rozycki -M: macro@linux-mips.org +M: "Maciej W. Rozycki" S: Maintained F: drivers/serial/dz.* EATA-DMA SCSI DRIVER -P: Michael Neuffer -M: mike@i-Connect.Net +M: Michael Neuffer L: linux-eata@i-connect.net L: linux-scsi@vger.kernel.org S: Maintained F: drivers/scsi/eata* EATA ISA/EISA/PCI SCSI DRIVER -P: Dario Ballabio -M: ballabio_dario@emc.com +M: Dario Ballabio L: linux-scsi@vger.kernel.org S: Maintained F: drivers/scsi/eata.c EATA-PIO SCSI DRIVER -P: Michael Neuffer -M: mike@i-Connect.Net +M: Michael Neuffer L: linux-eata@i-connect.net L: linux-scsi@vger.kernel.org S: Maintained F: drivers/scsi/eata_pio.* EBTABLES -P: Bart De Schuymer -M: bart.de.schuymer@pandora.be +M: Bart De Schuymer L: ebtables-user@lists.sourceforge.net L: ebtables-devel@lists.sourceforge.net W: http://ebtables.sourceforge.net/ @@ -2037,10 +1761,8 @@ F: include/linux/netfilter_bridge/ebt_*.h F: net/bridge/netfilter/ebt*.c ECRYPT FILE SYSTEM -P: Tyler Hicks -M: tyhicks@linux.vnet.ibm.com -P: Dustin Kirkland -M: kirkland@canonical.com +M: Tyler Hicks +M: Dustin Kirkland L: ecryptfs-devel@lists.launchpad.net W: https://launchpad.net/ecryptfs S: Supported @@ -2048,8 +1770,7 @@ F: Documentation/filesystems/ecryptfs.txt F: fs/ecryptfs/ EDAC-CORE -P: Doug Thompson -M: dougthompson@xmission.com +M: Doug Thompson L: bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers) W: bluesmoke.sourceforge.net S: Supported @@ -2058,94 +1779,80 @@ F: drivers/edac/edac_* F: include/linux/edac.h EDAC-AMD64 -P: Doug Thompson -M: dougthompson@xmission.com -P: Borislav Petkov -M: borislav.petkov@amd.com +M: Doug Thompson +M: Borislav Petkov L: bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers) W: bluesmoke.sourceforge.net S: Supported F: drivers/edac/amd64_edac* EDAC-E752X -P: Mark Gross -M: mark.gross@intel.com -P: Doug Thompson -M: dougthompson@xmission.com +M: Mark Gross +M: Doug Thompson L: bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers) W: bluesmoke.sourceforge.net S: Maintained F: drivers/edac/e752x_edac.c EDAC-E7XXX -P: Doug Thompson -M: dougthompson@xmission.com +M: Doug Thompson L: bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers) W: bluesmoke.sourceforge.net S: Maintained F: drivers/edac/e7xxx_edac.c EDAC-I82443BXGX -P: Tim Small -M: tim@buttersideup.com +M: Tim Small L: bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers) W: bluesmoke.sourceforge.net S: Maintained F: drivers/edac/i82443bxgx_edac.c EDAC-I3000 -P: Jason Uhlenkott -M: juhlenko@akamai.com +M: Jason Uhlenkott L: bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers) W: bluesmoke.sourceforge.net S: Maintained F: drivers/edac/i3000_edac.c EDAC-I5000 -P: Doug Thompson -M: dougthompson@xmission.com +M: Doug Thompson L: bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers) W: bluesmoke.sourceforge.net S: Maintained F: drivers/edac/i5000_edac.c EDAC-I5400 -P: Mauro Carvalho Chehab -M: mchehab@redhat.com +M: Mauro Carvalho Chehab L: bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers) W: bluesmoke.sourceforge.net S: Maintained F: drivers/edac/i5400_edac.c EDAC-I82975X -P: Ranganathan Desikan -M: ravi@jetztechnologies.com -P: Arvind R. -M: arvind@jetztechnologies.com +M: Ranganathan Desikan +M: "Arvind R." L: bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers) W: bluesmoke.sourceforge.net S: Maintained F: drivers/edac/i82975x_edac.c EDAC-PASEMI -P: Egor Martovetsky -M: egor@pasemi.com +M: Egor Martovetsky L: bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers) W: bluesmoke.sourceforge.net S: Maintained F: drivers/edac/pasemi_edac.c EDAC-R82600 -P: Tim Small -M: tim@buttersideup.com +M: Tim Small L: bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers) W: bluesmoke.sourceforge.net S: Maintained F: drivers/edac/r82600_edac.c EEEPC LAPTOP EXTRAS DRIVER -P: Corentin Chary -M: corentincj@iksaif.net +M: Corentin Chary L: acpi4asus-user@lists.sourceforge.net W: http://acpi4asus.sf.net S: Maintained @@ -2157,65 +1864,53 @@ S: Orphan F: fs/efs/ EHCA (IBM GX bus InfiniBand adapter) DRIVER -P: Hoang-Nam Nguyen -M: hnguyen@de.ibm.com -P: Christoph Raisch -M: raisch@de.ibm.com +M: Hoang-Nam Nguyen +M: Christoph Raisch L: general@lists.openfabrics.org S: Supported F: drivers/infiniband/hw/ehca/ EMBEDDED LINUX -P: Paul Gortmaker -M: paul.gortmaker@windriver.com -P: Matt Mackall -M: mpm@selenic.com -P: David Woodhouse -M: dwmw2@infradead.org +M: Paul Gortmaker +M: Matt Mackall +M: David Woodhouse L: linux-embedded@vger.kernel.org S: Maintained EMULEX LPFC FC SCSI DRIVER -P: James Smart -M: james.smart@emulex.com +M: James Smart L: linux-scsi@vger.kernel.org W: http://sourceforge.net/projects/lpfcxxxx S: Supported F: drivers/scsi/lpfc/ ENE CB710 FLASH CARD READER DRIVER -P: MichaÅ‚ MirosÅ‚aw -M: mirq-linux@rere.qmqm.pl +M: MichaÅ‚ MirosÅ‚aw S: Maintained F: drivers/misc/cb710/ F: drivers/mmc/host/cb710-mmc.* F: include/linux/cb710.h EPSON 1355 FRAMEBUFFER DRIVER -P: Christopher Hoover -M: ch@murgatroid.com -P: Christopher Hoover -M: ch@hpl.hp.com +M: Christopher Hoover +M: Christopher Hoover S: Maintained F: drivers/video/epson1355fb.c EPSON S1D13XXX FRAMEBUFFER DRIVER -P: Kristoffer Ericson -M: kristoffer.ericson@gmail.com +M: Kristoffer Ericson S: Maintained F: drivers/video/s1d13xxxfb.c F: include/video/s1d13xxxfb.h ETHEREXPRESS-16 NETWORK DRIVER -P: Philip Blundell -M: philb@gnu.org +M: Philip Blundell L: netdev@vger.kernel.org S: Maintained F: drivers/net/eexpress.* ETHERNET BRIDGE -P: Stephen Hemminger -M: shemminger@linux-foundation.org +M: Stephen Hemminger L: bridge@lists.linux-foundation.org W: http://www.linux-foundation.org/en/Net:Bridge S: Maintained @@ -2223,8 +1918,7 @@ F: include/linux/netfilter_bridge/ F: net/bridge/ ETHERTEAM 16I DRIVER -P: Mika Kuoppala -M: miku@iki.fi +M: Mika Kuoppala S: Maintained F: drivers/net/eth16i.c @@ -2236,12 +1930,9 @@ F: fs/ext2/ F: include/linux/ext2* EXT3 FILE SYSTEM -P: Stephen Tweedie -M: sct@redhat.com -P: Andrew Morton -M: akpm@linux-foundation.org -P: Andreas Dilger -M: adilger@sun.com +M: Stephen Tweedie +M: Andrew Morton +M: Andreas Dilger L: linux-ext4@vger.kernel.org S: Maintained F: Documentation/filesystems/ext3.txt @@ -2249,10 +1940,8 @@ F: fs/ext3/ F: include/linux/ext3* EXT4 FILE SYSTEM -P: Theodore Ts'o -M: tytso@mit.edu -P: Andreas Dilger -M: adilger@sun.com +M: "Theodore Ts'o" +M: Andreas Dilger L: linux-ext4@vger.kernel.org W: http://ext4.wiki.kernel.org S: Maintained @@ -2260,30 +1949,26 @@ F: Documentation/filesystems/ext4.txt F: fs/ext4/ F71805F HARDWARE MONITORING DRIVER -P: Jean Delvare -M: khali@linux-fr.org +M: Jean Delvare L: lm-sensors@lm-sensors.org S: Maintained F: Documentation/hwmon/f71805f F: drivers/hwmon/f71805f.c FARSYNC SYNCHRONOUS DRIVER -P: Kevin Curtis -M: kevin.curtis@farsite.co.uk +M: Kevin Curtis W: http://www.farsite.co.uk/ S: Supported F: drivers/net/wan/farsync.* FAULT INJECTION SUPPORT -P: Akinobu Mita -M: akinobu.mita@gmail.com +M: Akinobu Mita S: Supported F: Documentation/fault-injection/ F: lib/fault-inject.c FILE LOCKING (flock() and fcntl()/lockf()) -P: Matthew Wilcox -M: matthew@wil.cx +M: Matthew Wilcox L: linux-fsdevel@vger.kernel.org S: Maintained F: include/linux/fcntl.h @@ -2292,25 +1977,21 @@ F: fs/fcntl.c F: fs/locks.c FILESYSTEMS (VFS and infrastructure) -P: Alexander Viro -M: viro@zeniv.linux.org.uk +M: Alexander Viro L: linux-fsdevel@vger.kernel.org S: Maintained F: fs/* FINTEK F75375S HARDWARE MONITOR AND FAN CONTROLLER DRIVER -P: Riku Voipio -M: riku.vipio@iki.fi +M: Riku Voipio L: lm-sensors@lm-sensors.org S: Maintained F: drivers/hwmon/f75375s.c F: include/linux/f75375s.h FIREWIRE SUBSYSTEM -P: Kristian Hoegsberg -M: krh@redhat.com -P: Stefan Richter -M: stefanr@s5r6.in-berlin.de +M: Kristian Hoegsberg +M: Stefan Richter L: linux1394-devel@lists.sourceforge.net W: http://www.linux1394.org/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6.git @@ -2325,15 +2006,13 @@ F: drivers/base/firmware*.c F: include/linux/firmware.h FPU EMULATOR -P: Bill Metzenthen -M: billm@melbpc.org.au +M: Bill Metzenthen W: http://floatingpoint.sourceforge.net/emulator/index.html S: Maintained F: arch/x86/math-emu/ FRAME RELAY DLCI/FRAD (Sangoma drivers too) -P: Mike McLagan -M: mike.mclagan@linux.org +M: Mike McLagan L: netdev@vger.kernel.org S: Maintained F: drivers/net/wan/dlci.c @@ -2348,25 +2027,21 @@ F: drivers/video/fb* F: include/linux/fb.h FREESCALE DMA DRIVER -P: Li Yang -M: leoli@freescale.com -P: Zhang Wei -M: zw@zh-kernel.org +M: Li Yang +M: Zhang Wei L: linuxppc-dev@ozlabs.org S: Maintained F: drivers/dma/fsldma.* FREESCALE I2C CPM DRIVER -P: Jochen Friedrich -M: jochen@scram.de +M: Jochen Friedrich L: linuxppc-dev@ozlabs.org L: linux-i2c@vger.kernel.org S: Maintained F: drivers/i2c/busses/i2c-cpm.c FREESCALE IMX / MXC FRAMEBUFFER DRIVER -P: Sascha Hauer -M: kernel@pengutronix.de +M: Sascha Hauer L: linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers) L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained @@ -2374,10 +2049,8 @@ F: arch/arm/plat-mxc/include/mach/imxfb.h F: drivers/video/imxfb.c FREESCALE SOC FS_ENET DRIVER -P: Pantelis Antoniou -M: pantelis.antoniou@gmail.com -P: Vitaly Bordug -M: vbordug@ru.mvista.com +M: Pantelis Antoniou +M: Vitaly Bordug L: linuxppc-dev@ozlabs.org L: netdev@vger.kernel.org S: Maintained @@ -2385,39 +2058,34 @@ F: drivers/net/fs_enet/ F: include/linux/fs_enet_pd.h FREESCALE QUICC ENGINE LIBRARY -P: Timur Tabi -M: timur@freescale.com +M: Timur Tabi L: linuxppc-dev@ozlabs.org S: Supported F: arch/powerpc/sysdev/qe_lib/ F: arch/powerpc/include/asm/*qe.h FREESCALE HIGHSPEED USB DEVICE DRIVER -P: Li Yang -M: leoli@freescale.com +M: Li Yang L: linux-usb@vger.kernel.org L: linuxppc-dev@ozlabs.org S: Maintained F: drivers/usb/gadget/fsl_usb2_udc.c FREESCALE QUICC ENGINE UCC ETHERNET DRIVER -P: Li Yang -M: leoli@freescale.com +M: Li Yang L: netdev@vger.kernel.org L: linuxppc-dev@ozlabs.org S: Maintained F: drivers/net/ucc_geth* FREESCALE QUICC ENGINE UCC UART DRIVER -P: Timur Tabi -M: timur@freescale.com +M: Timur Tabi L: linuxppc-dev@ozlabs.org S: Supported F: drivers/serial/ucc_uart.c FREESCALE SOC SOUND DRIVERS -P: Timur Tabi -M: timur@freescale.com +M: Timur Tabi L: alsa-devel@alsa-project.org (moderated for non-subscribers) L: linuxppc-dev@ozlabs.org S: Supported @@ -2425,17 +2093,14 @@ F: sound/soc/fsl/fsl* F: sound/soc/fsl/mpc8610_hpcd.c FREEVXFS FILESYSTEM -P: Christoph Hellwig -M: hch@infradead.org +M: Christoph Hellwig W: ftp://ftp.openlinux.org/pub/people/hch/vxfs S: Maintained F: fs/freevxfs/ FREEZER -P: Pavel Machek -M: pavel@ucw.cz -P: Rafael J. Wysocki -M: rjw@sisk.pl +M: Pavel Machek +M: "Rafael J. Wysocki" L: linux-pm@lists.linux-foundation.org S: Supported F: Documentation/power/freezing-of-tasks.txt @@ -2443,8 +2108,7 @@ F: include/linux/freezer.h F: kernel/freezer.c FS-CACHE: LOCAL CACHING FOR NETWORK FILESYSTEMS -P: David Howells -M: dhowells@redhat.com +M: David Howells L: linux-cachefs@redhat.com S: Supported F: Documentation/filesystems/caching/ @@ -2452,8 +2116,7 @@ F: fs/fscache/ F: include/linux/fscache*.h FTRACE -P: Steven Rostedt -M: rostedt@goodmis.org +M: Steven Rostedt S: Maintained F: Documentation/trace/ftrace.txt F: arch/*/*/*/ftrace.h @@ -2462,21 +2125,18 @@ F: include/*/ftrace.h F: kernel/trace/ FUJITSU FR-V (FRV) PORT -P: David Howells -M: dhowells@redhat.com +M: David Howells S: Maintained F: arch/frv/ FUJITSU LAPTOP EXTRAS -P: Jonathan Woithe -M: jwoithe@physics.adelaide.edu.au +M: Jonathan Woithe L: linux-acpi@vger.kernel.org S: Maintained F: drivers/platform/x86/fujitsu-laptop.c FUSE: FILESYSTEM IN USERSPACE -P: Miklos Szeredi -M: miklos@szeredi.hu +M: Miklos Szeredi L: fuse-devel@lists.sourceforge.net W: http://fuse.sourceforge.net/ S: Maintained @@ -2484,30 +2144,26 @@ F: fs/fuse/ F: include/linux/fuse.h FUTURE DOMAIN TMC-16x0 SCSI DRIVER (16-bit) -P: Rik Faith -M: faith@cs.unc.edu +M: Rik Faith L: linux-scsi@vger.kernel.org S: Odd Fixes (e.g., new signatures) F: drivers/scsi/fdomain.* GDT SCSI DISK ARRAY CONTROLLER DRIVER -P: Achim Leubner -M: achim_leubner@adaptec.com +M: Achim Leubner L: linux-scsi@vger.kernel.org W: http://www.icp-vortex.com/ S: Supported F: drivers/scsi/gdt* GENERIC GPIO I2C DRIVER -P: Haavard Skinnemoen -M: hskinnemoen@atmel.com +M: Haavard Skinnemoen S: Supported F: drivers/i2c/busses/i2c-gpio.c F: include/linux/i2c-gpio.h GENERIC HDLC (WAN) DRIVERS -P: Krzysztof Halasa -M: khc@pm.waw.pl +M: Krzysztof Halasa W: http://www.kernel.org/pub/linux/utils/net/hdlc/ S: Maintained F: drivers/net/wan/c101.c @@ -2519,16 +2175,14 @@ F: drivers/net/wan/pci200syn.c F: drivers/net/wan/wanxl* GENERIC INCLUDE/ASM HEADER FILES -P: Arnd Bergmann -M: arnd@arndb.de +M: Arnd Bergmann L: linux-arch@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic.git S: Maintained F: include/asm-generic GFS2 FILE SYSTEM -P: Steven Whitehouse -M: swhiteho@redhat.com +M: Steven Whitehouse L: cluster-devel@redhat.com W: http://sources.redhat.com/cluster/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes.git @@ -2539,10 +2193,8 @@ F: fs/gfs2/ F: include/linux/gfs2_ondisk.h GIGASET ISDN DRIVERS -P: Hansjoerg Lipp -M: hjlipp@web.de -P: Tilman Schmidt -M: tilman@imap.cc +M: Hansjoerg Lipp +M: Tilman Schmidt L: gigaset307x-common@lists.sourceforge.net W: http://gigaset307x.sourceforge.net/ S: Maintained @@ -2551,8 +2203,7 @@ F: drivers/isdn/gigaset/ F: include/linux/gigaset_dev.h HARD DRIVE ACTIVE PROTECTION SYSTEM (HDAPS) DRIVER -P: Frank Seidel -M: frank@f-seidel.de +M: Frank Seidel L: lm-sensors@lm-sensors.org W: http://www.kernel.org/pub/linux/kernel/people/fseidel/hdaps/ S: Maintained @@ -2564,40 +2215,35 @@ S: Odd Fixes F: drivers/char/hvc_* GSPCA FINEPIX SUBDRIVER -P: Frank Zago -M: frank@zago.net +M: Frank Zago L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git S: Maintained F: drivers/media/video/gspca/finepix.c GSPCA M5602 SUBDRIVER -P: Erik Andren -M: erik.andren@gmail.com +M: Erik Andren L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git S: Maintained F: drivers/media/video/gspca/m5602/ GSPCA PAC207 SONIXB SUBDRIVER -P: Hans de Goede -M: hdegoede@redhat.com +M: Hans de Goede L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git S: Maintained F: drivers/media/video/gspca/pac207.c GSPCA T613 SUBDRIVER -P: Leandro Costantino -M: lcostantino@gmail.com +M: Leandro Costantino L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git S: Maintained F: drivers/media/video/gspca/t613.c GSPCA USB WEBCAM DRIVER -P: Jean-Francois Moine -M: moinejf@free.fr +M: Jean-Francois Moine W: http://moinejf.free.fr L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git @@ -2617,31 +2263,27 @@ F: drivers/char/hw_random/ F: include/linux/hw_random.h HARMONY SOUND DRIVER -P: Kyle McMartin -M: kyle@mcmartin.ca +M: Kyle McMartin L: linux-parisc@vger.kernel.org S: Maintained F: sound/parisc/harmony.* HAYES ESP SERIAL DRIVER -P: Andrew J. Robinson -M: arobinso@nyx.net +M: "Andrew J. Robinson" W: http://www.nyx.net/~arobinso S: Maintained F: Documentation/serial/hayes-esp.txt F: drivers/char/esp.c HEWLETT-PACKARD SMART2 RAID DRIVER -P: Chirag Kantharia -M: chirag.kantharia@hp.com +M: Chirag Kantharia L: iss_storagedev@hp.com S: Maintained F: Documentation/blockdev/cpqarray.txt F: drivers/block/cpqarray.* HEWLETT-PACKARD SMART CISS RAID DRIVER (cciss) -P: Mike Miller -M: mike.miller@hp.com +M: Mike Miller L: iss_storagedev@hp.com S: Supported F: Documentation/blockdev/cciss.txt @@ -2649,25 +2291,21 @@ F: drivers/block/cciss* F: include/linux/cciss_ioctl.h HFS FILESYSTEM -P: Roman Zippel -M: zippel@linux-m68k.org +M: Roman Zippel S: Maintained F: Documentation/filesystems/hfs.txt F: fs/hfs/ HGA FRAMEBUFFER DRIVER -P: Ferenc Bakonyi -M: fero@drama.obuda.kando.hu +M: Ferenc Bakonyi L: linux-nvidia@lists.surfsouth.com W: http://drama.obuda.kando.hu/~fero/cgi-bin/hgafb.shtml S: Maintained F: drivers/video/hgafb.c HIBERNATION (aka Software Suspend, aka swsusp) -P: Pavel Machek -M: pavel@ucw.cz -P: Rafael J. Wysocki -M: rjw@sisk.pl +M: Pavel Machek +M: "Rafael J. Wysocki" L: linux-pm@lists.linux-foundation.org S: Supported F: arch/x86/power/ @@ -2679,8 +2317,7 @@ F: include/linux/pm.h F: arch/*/include/asm/suspend*.h HID CORE LAYER -P: Jiri Kosina -M: jkosina@suse.cz +M: Jiri Kosina L: linux-input@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid.git S: Maintained @@ -2688,16 +2325,14 @@ F: drivers/hid/ F: include/linux/hid* HIGH-RESOLUTION TIMERS, CLOCKEVENTS, DYNTICKS -P: Thomas Gleixner -M: tglx@linutronix.de +M: Thomas Gleixner S: Maintained F: Documentation/timers/ F: kernel/hrtimer.c F: include/linux/hrtimer.h HIGH-SPEED SCC DRIVER FOR AX.25 -P: Klaus Kudielka -M: klaus.kudielka@ieee.org +M: Klaus Kudielka L: linux-hams@vger.kernel.org W: http://www.nt.tuwien.ac.at/~kkudielk/Linux/ S: Maintained @@ -2705,16 +2340,14 @@ F: drivers/net/hamradio/dmascc.c F: drivers/net/hamradio/scc.c HIGHPOINT ROCKETRAID 3xxx RAID DRIVER -P: HighPoint Linux Team -M: linux@highpoint-tech.com +M: HighPoint Linux Team W: http://www.highpoint-tech.com S: Supported F: Documentation/scsi/hptiop.txt F: drivers/scsi/hptiop.c HIPPI -P: Jes Sorensen -M: jes@trained-monkey.org +M: Jes Sorensen L: linux-hippi@sunsite.dk S: Maintained F: include/linux/hippidevice.h @@ -2722,8 +2355,7 @@ F: include/linux/if_hippi.h F: net/802/hippi.c HOST AP DRIVER -P: Jouni Malinen -M: j@w1.fi +M: Jouni Malinen L: hostap@shmoo.com (subscribers-only) L: linux-wireless@vger.kernel.org W: http://hostap.epitest.fi/ @@ -2731,82 +2363,69 @@ S: Maintained F: drivers/net/wireless/hostap/ HP COMPAQ TC1100 TABLET WMI EXTRAS DRIVER -P: Carlos Corbacho -M: carlos@strangeworlds.co.uk +M: Carlos Corbacho S: Odd Fixes F: drivers/platform/x86/tc1100-wmi.c HP100: Driver for HP 10/100 Mbit/s Voice Grade Network Adapter Series -P: Jaroslav Kysela -M: perex@perex.cz +M: Jaroslav Kysela S: Maintained F: drivers/net/hp100.* HPET: High Precision Event Timers driver -P: Clemens Ladisch -M: clemens@ladisch.de +M: Clemens Ladisch S: Maintained F: Documentation/timers/hpet.txt F: drivers/char/hpet.c F: include/linux/hpet.h HPET: i386 -P: Venkatesh Pallipadi (Venki) -M: venkatesh.pallipadi@intel.com +M: "Venkatesh Pallipadi (Venki)" S: Maintained F: arch/x86/kernel/hpet.c F: arch/x86/include/asm/hpet.h HPET: x86_64 -P: Vojtech Pavlik -M: vojtech@suse.cz +M: Vojtech Pavlik S: Maintained HPET: ACPI -P: Bob Picco -M: bob.picco@hp.com +M: Bob Picco S: Maintained F: drivers/char/hpet.c HPFS FILESYSTEM -P: Mikulas Patocka -M: mikulas@artax.karlin.mff.cuni.cz +M: Mikulas Patocka W: http://artax.karlin.mff.cuni.cz/~mikulas/vyplody/hpfs/index-e.cgi S: Maintained F: fs/hpfs/ HSO 3G MODEM DRIVER -P: Jan Dumon -M: j.dumon@option.com +M: Jan Dumon W: http://www.pharscape.org S: Maintained F: drivers/net/usb/hso.c HTCPEN TOUCHSCREEN DRIVER -P: Pau Oliva Fora -M: pof@eslack.org +M: Pau Oliva Fora L: linux-input@vger.kernel.org S: Maintained F: drivers/input/touchscreen/htcpen.c HUGETLB FILESYSTEM -P: William Irwin -M: wli@holomorphy.com +M: William Irwin S: Maintained F: fs/hugetlbfs/ I2C/SMBUS STUB DRIVER -P: Mark M. Hoffman -M: mhoffman@lightlink.com +M: "Mark M. Hoffman" L: linux-i2c@vger.kernel.org S: Maintained F: drivers/i2c/busses/i2c-stub.c I2C SUBSYSTEM -P: Jean Delvare (PC drivers, core) -M: khali@linux-fr.org -P: Ben Dooks (embedded platforms) -M: ben-linux@fluff.org +M: "Jean Delvare (PC drivers, core)" +M: "Ben Dooks (embedded platforms)" L: linux-i2c@vger.kernel.org W: http://i2c.wiki.kernel.org/ T: quilt kernel.org/pub/linux/kernel/people/jdelvare/linux-2.6/jdelvare-i2c/ @@ -2818,30 +2437,25 @@ F: include/linux/i2c-dev.h F: include/linux/i2c-id.h I2C-TINY-USB DRIVER -P: Till Harbaum -M: till@harbaum.org +M: Till Harbaum L: linux-i2c@vger.kernel.org W: http://www.harbaum.org/till/i2c_tiny_usb S: Maintained F: drivers/i2c/busses/i2c-tiny-usb.c i386 BOOT CODE -P: H. Peter Anvin -M: hpa@zytor.com +M: "H. Peter Anvin" S: Maintained F: arch/x86/boot/ i386 SETUP CODE / CPU ERRATA WORKAROUNDS -P: H. Peter Anvin -M: hpa@zytor.com +M: "H. Peter Anvin" T: git git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup.git S: Maintained IA64 (Itanium) PLATFORM -P: Tony Luck -M: tony.luck@intel.com -P: Fenghua Yu -M: fenghua.yu@intel.com +M: Tony Luck +M: Fenghua Yu L: linux-ia64@vger.kernel.org W: http://www.ia64-linux.org/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6.git @@ -2849,29 +2463,25 @@ S: Maintained F: arch/ia64/ IBM MCA SCSI SUBSYSTEM DRIVER -P: Michael Lang -M: langa2@kph.uni-mainz.de +M: Michael Lang W: http://www.uni-mainz.de/~langm000/linux.html S: Maintained F: drivers/scsi/ibmmca.c IBM Power Linux RAID adapter -P: Brian King -M: brking@us.ibm.com +M: Brian King S: Supported F: drivers/scsi/ipr.* IBM ServeRAID RAID DRIVER P: Jack Hammer -P: Dave Jeffery -M: ipslinux@adaptec.com +M: Dave Jeffery W: http://www.developer.ibm.com/welcome/netfinity/serveraid.html S: Supported F: drivers/scsi/ips.* IDE SUBSYSTEM -P: David S. Miller -M: davem@davemloft.net +M: "David S. Miller" L: linux-ide@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6.git S: Maintained @@ -2880,25 +2490,21 @@ F: drivers/ide/ F: include/linux/ide.h IDE/ATAPI DRIVERS -P: Borislav Petkov -M: petkovbb@gmail.com +M: Borislav Petkov L: linux-ide@vger.kernel.org S: Maintained F: Documentation/cdrom/ide-cd F: drivers/ide/ide-cd* IDLE-I7300 -P: Andy Henroid -M: andrew.d.henroid@intel.com +M: Andy Henroid L: linux-pm@lists.linux-foundation.org S: Supported F: drivers/idle/i7300_idle.c IEEE 1394 SUBSYSTEM -P: Ben Collins -M: ben.collins@ubuntu.com -P: Stefan Richter -M: stefanr@s5r6.in-berlin.de +M: Ben Collins +M: Stefan Richter L: linux1394-devel@lists.sourceforge.net W: http://www.linux1394.org/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6.git @@ -2906,19 +2512,15 @@ S: Maintained F: drivers/ieee1394/ IEEE 1394 RAW I/O DRIVER -P: Dan Dennedy -M: dan@dennedy.org -P: Stefan Richter -M: stefanr@s5r6.in-berlin.de +M: Dan Dennedy +M: Stefan Richter L: linux1394-devel@lists.sourceforge.net S: Maintained F: drivers/ieee1394/raw1394* IEEE 802.15.4 SUBSYSTEM -P: Dmitry Eremin-Solenikov -M: dbaryshkov@gmail.com -P: Sergey Lapin -M: slapin@ossfans.org +M: Dmitry Eremin-Solenikov +M: Sergey Lapin L: linux-zigbee-devel@lists.sourceforge.net (moderated for non-subscribers) W: http://apps.sourceforge.net/trac/linux-zigbee T: git git://git.kernel.org/pub/scm/linux/kernel/git/lowpan/lowpan.git @@ -2927,8 +2529,7 @@ F: net/ieee802154/ F: drivers/ieee802154/ INTEGRITY MEASUREMENT ARCHITECTURE (IMA) -P: Mimi Zohar -M: zohar@us.ibm.com +M: Mimi Zohar S: Supported F: security/integrity/ima/ @@ -2938,12 +2539,9 @@ S: Orphan F: drivers/video/imsttfb.c INFINIBAND SUBSYSTEM -P: Roland Dreier -M: rolandd@cisco.com -P: Sean Hefty -M: sean.hefty@intel.com -P: Hal Rosenstock -M: hal.rosenstock@gmail.com +M: Roland Dreier +M: Sean Hefty +M: Hal Rosenstock L: general@lists.openfabrics.org (moderated for non-subscribers) W: http://www.openib.org/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband.git @@ -2953,66 +2551,55 @@ F: drivers/infiniband/ F: include/linux/if_infiniband.h INOTIFY -P: John McCutchan -M: john@johnmccutchan.com -P: Robert Love -M: rlove@rlove.org -P: Eric Paris -M: eparis@parisplace.org +M: John McCutchan +M: Robert Love +M: Eric Paris S: Maintained F: Documentation/filesystems/inotify.txt F: fs/notify/inotify/ F: include/linux/inotify.h INPUT (KEYBOARD, MOUSE, JOYSTICK, TOUCHSCREEN) DRIVERS -P: Dmitry Torokhov -M: dmitry.torokhov@gmail.com -P: Dmitry Torokhov -M: dtor@mail.ru +M: Dmitry Torokhov +M: Dmitry Torokhov L: linux-input@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input.git S: Maintained F: drivers/input/ INTEL FRAMEBUFFER DRIVER (excluding 810 and 815) -P: Sylvain Meyer -M: sylvain.meyer@worldonline.fr +M: Sylvain Meyer L: linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers) S: Maintained F: Documentation/fb/intelfb.txt F: drivers/video/intelfb/ INTEL 810/815 FRAMEBUFFER DRIVER -P: Antonino Daplas -M: adaplas@gmail.com +M: Antonino Daplas L: linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers) S: Maintained F: drivers/video/i810/ INTEL MENLOW THERMAL DRIVER -P: Sujith Thomas -M: sujith.thomas@intel.com +M: Sujith Thomas L: linux-acpi@vger.kernel.org W: http://www.lesswatts.org/projects/acpi/ S: Supported F: drivers/platform/x86/intel_menlow.c INTEL IA32 MICROCODE UPDATE SUPPORT -P: Tigran Aivazian -M: tigran@aivazian.fsnet.co.uk +M: Tigran Aivazian S: Maintained F: arch/x86/kernel/microcode_core.c F: arch/x86/kernel/microcode_intel.c INTEL I/OAT DMA DRIVER -P: Maciej Sosnowski -M: maciej.sosnowski@intel.com +M: Maciej Sosnowski S: Supported F: drivers/dma/ioat* INTEL IOMMU (VT-d) -P: David Woodhouse -M: dwmw2@infradead.org +M: David Woodhouse L: iommu@lists.linux-foundation.org T: git git://git.infradead.org/iommu-2.6.git S: Supported @@ -3020,14 +2607,12 @@ F: drivers/pci/intel-iommu.c F: include/linux/intel-iommu.h INTEL IOP-ADMA DMA DRIVER -P: Dan Williams -M: dan.j.williams@intel.com +M: Dan Williams S: Supported F: drivers/dma/iop-adma.c INTEL IXP4XX QMGR, NPE, ETHERNET and HSS SUPPORT -P: Krzysztof Halasa -M: khc@pm.waw.pl +M: Krzysztof Halasa S: Maintained F: arch/arm/mach-ixp4xx/include/mach/qmgr.h F: arch/arm/mach-ixp4xx/include/mach/npe.h @@ -3037,29 +2622,22 @@ F: drivers/net/arm/ixp4xx_eth.c F: drivers/net/wan/ixp4xx_hss.c INTEL IXP4XX RANDOM NUMBER GENERATOR SUPPORT -P: Deepak Saxena -M: dsaxena@plexity.net +M: Deepak Saxena S: Maintained F: drivers/char/hw_random/ixp4xx-rng.c INTEL IXP2000 ETHERNET DRIVER -P: Lennert Buytenhek -M: kernel@wantstofly.org +M: Lennert Buytenhek L: netdev@vger.kernel.org S: Maintained F: drivers/net/ixp2000/ INTEL ETHERNET DRIVERS (e100/e1000/e1000e/igb/ixgb/ixgbe) -P: Jeff Kirsher -M: jeffrey.t.kirsher@intel.com -P: Jesse Brandeburg -M: jesse.brandeburg@intel.com -P: Bruce Allan -M: bruce.w.allan@intel.com -P: PJ Waskiewicz -M: peter.p.waskiewicz.jr@intel.com -P: John Ronciak -M: john.ronciak@intel.com +M: Jeff Kirsher +M: Jesse Brandeburg +M: Bruce Allan +M: PJ Waskiewicz +M: John Ronciak L: e1000-devel@lists.sourceforge.net W: http://e1000.sourceforge.net/ S: Supported @@ -3071,12 +2649,9 @@ F: drivers/net/ixgb/ F: drivers/net/ixgbe/ INTEL PRO/WIRELESS 2100 NETWORK CONNECTION SUPPORT -P: Zhu Yi -M: yi.zhu@intel.com -P: James Ketrenos -M: jketreno@linux.intel.com -P: Reinette Chatre -M: reinette.chatre@intel.com +M: Zhu Yi +M: James Ketrenos +M: Reinette Chatre L: linux-wireless@vger.kernel.org L: ipw2100-devel@lists.sourceforge.net W: http://lists.sourceforge.net/mailman/listinfo/ipw2100-devel @@ -3086,12 +2661,9 @@ F: Documentation/networking/README.ipw2100 F: drivers/net/wireless/ipw2x00/ipw2100.* INTEL PRO/WIRELESS 2915ABG NETWORK CONNECTION SUPPORT -P: Zhu Yi -M: yi.zhu@intel.com -P: James Ketrenos -M: jketreno@linux.intel.com -P: Reinette Chatre -M: reinette.chatre@intel.com +M: Zhu Yi +M: James Ketrenos +M: Reinette Chatre L: linux-wireless@vger.kernel.org L: ipw2100-devel@lists.sourceforge.net W: http://lists.sourceforge.net/mailman/listinfo/ipw2100-devel @@ -3101,8 +2673,7 @@ F: Documentation/networking/README.ipw2200 F: drivers/net/wireless/ipw2x00/ipw2200.* INTEL WIRELESS WIMAX CONNECTION 2400 -P: Inaky Perez-Gonzalez -M: inaky.perez-gonzalez@intel.com +M: Inaky Perez-Gonzalez M: linux-wimax@intel.com L: wimax@linuxwimax.org S: Supported @@ -3112,10 +2683,8 @@ F: drivers/net/wimax/i2400m/ F: include/linux/wimax/i2400m.h INTEL WIRELESS WIFI LINK (iwlwifi) -P: Zhu Yi -M: yi.zhu@intel.com -P: Reinette Chatre -M: reinette.chatre@intel.com +M: Zhu Yi +M: Reinette Chatre L: linux-wireless@vger.kernel.org L: ipw3945-devel@lists.sourceforge.net W: http://intellinuxwireless.org @@ -3124,47 +2693,39 @@ S: Supported F: drivers/net/wireless/iwlwifi/ IOC3 ETHERNET DRIVER -P: Ralf Baechle -M: ralf@linux-mips.org +M: Ralf Baechle L: linux-mips@linux-mips.org S: Maintained F: drivers/net/ioc3-eth.c IOC3 SERIAL DRIVER -P: Pat Gefre -M: pfg@sgi.com +M: Pat Gefre L: linux-mips@linux-mips.org S: Maintained F: drivers/serial/ioc3_serial.c IP MASQUERADING -P: Juanjo Ciarlante -M: jjciarla@raiz.uncu.edu.ar +M: Juanjo Ciarlante S: Maintained F: net/ipv4/netfilter/ipt_MASQUERADE.c IP1000A 10/100/1000 GIGABIT ETHERNET DRIVER -P: Francois Romieu -M: romieu@fr.zoreil.com -P: Sorbica Shieh -M: sorbica@icplus.com.tw -P: Jesse Huang -M: jesse@icplus.com.tw +M: Francois Romieu +M: Sorbica Shieh +M: Jesse Huang L: netdev@vger.kernel.org S: Maintained F: drivers/net/ipg.c IPATH DRIVER -P: Ralph Campbell -M: infinipath@qlogic.com +M: Ralph Campbell L: general@lists.openfabrics.org T: git git://git.qlogic.com/ipath-linux-2.6 S: Supported F: drivers/infiniband/hw/ipath/ IPMI SUBSYSTEM -P: Corey Minyard -M: minyard@acm.org +M: Corey Minyard L: openipmi-developer@lists.sourceforge.net W: http://openipmi.sourceforge.net/ S: Supported @@ -3173,20 +2734,16 @@ F: drivers/char/ipmi/ F: include/linux/ipmi* IPS SCSI RAID DRIVER -P: Adaptec OEM Raid Solutions -M: aacraid@adaptec.com +M: Adaptec OEM Raid Solutions L: linux-scsi@vger.kernel.org W: http://www.adaptec.com/ S: Maintained F: drivers/scsi/ips* IPVS -P: Wensong Zhang -M: wensong@linux-vs.org -P: Simon Horman -M: horms@verge.net.au -P: Julian Anastasov -M: ja@ssi.bg +M: Wensong Zhang +M: Simon Horman +M: Julian Anastasov L: netdev@vger.kernel.org L: lvs-devel@vger.kernel.org S: Maintained @@ -3194,17 +2751,14 @@ F: Documentation/networking/ipvs-sysctl.txt F: net/netfilter/ipvs/ IPWIRELESS DRIVER -P: Jiri Kosina -M: jkosina@suse.cz -P: David Sterba -M: dsterba@suse.cz +M: Jiri Kosina +M: David Sterba S: Maintained T: git git://git.kernel.org/pub/scm/linux/kernel/git/jikos/ipwireless_cs.git F: drivers/char/pcmcia/ipwireless/ IPX NETWORK LAYER -P: Arnaldo Carvalho de Melo -M: acme@ghostprotocols.net +M: Arnaldo Carvalho de Melo L: netdev@vger.kernel.org S: Maintained F: include/linux/ipx.h @@ -3212,8 +2766,7 @@ F: include/net/ipx.h F: net/ipx/ IRDA SUBSYSTEM -P: Samuel Ortiz -M: samuel@sortiz.org +M: Samuel Ortiz L: irda-users@lists.sourceforge.net (subscribers-only) W: http://irda.sourceforge.net/ S: Maintained @@ -3224,16 +2777,14 @@ F: include/net/irda/ F: net/irda/ ISAPNP -P: Jaroslav Kysela -M: perex@perex.cz +M: Jaroslav Kysela S: Maintained F: Documentation/isapnp.txt F: drivers/pnp/isapnp/ F: include/linux/isapnp.h ISCSI -P: Mike Christie -M: michaelc@cs.wisc.edu +M: Mike Christie L: open-iscsi@googlegroups.com W: www.open-iscsi.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mnc/linux-2.6-iscsi.git @@ -3242,8 +2793,7 @@ F: drivers/scsi/*iscsi* F: include/scsi/*iscsi* ISDN SUBSYSTEM -P: Karsten Keil -M: isdn@linux-pingi.de +M: Karsten Keil L: isdn4linux@listserv.isdn4linux.de (subscribers-only) W: http://www.isdn4linux.de T: git git://git.kernel.org/pub/scm/linux/kernel/git/kkeil/isdn-2.6.git @@ -3254,16 +2804,14 @@ F: include/linux/isdn.h F: include/linux/isdn/ ISDN SUBSYSTEM (Eicon active card driver) -P: Armin Schindler -M: mac@melware.de +M: Armin Schindler L: isdn4linux@listserv.isdn4linux.de (subscribers-only) W: http://www.melware.de S: Maintained F: drivers/isdn/hardware/eicon/ IVTV VIDEO4LINUX DRIVER -P: Hans Verkuil -M: hverkuil@xs4all.nl +M: Hans Verkuil L: ivtv-devel@ivtvdriver.org L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git @@ -3274,8 +2822,7 @@ F: drivers/media/video/ivtv/ F: include/linux/ivtv* JFS FILESYSTEM -P: Dave Kleikamp -M: shaggy@linux.vnet.ibm.com +M: Dave Kleikamp L: jfs-discussion@lists.sourceforge.net W: http://jfs.sourceforge.net/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6.git @@ -3284,15 +2831,13 @@ F: Documentation/filesystems/jfs.txt F: fs/jfs/ JME NETWORK DRIVER -P: Guo-Fu Tseng -M: cooldavid@cooldavid.org +M: Guo-Fu Tseng L: netdev@vger.kernel.org S: Maintained F: drivers/net/jme.* JOURNALLING FLASH FILE SYSTEM V2 (JFFS2) -P: David Woodhouse -M: dwmw2@infradead.org +M: David Woodhouse L: linux-mtd@lists.infradead.org W: http://www.linux-mtd.infradead.org/doc/jffs2.html S: Maintained @@ -3300,10 +2845,8 @@ F: fs/jffs2/ F: include/linux/jffs2.h JOURNALLING LAYER FOR BLOCK DEVICES (JBD) -P: Stephen Tweedie -M: sct@redhat.com -P: Andrew Morton -M: akpm@linux-foundation.org +M: Stephen Tweedie +M: Andrew Morton L: linux-ext4@vger.kernel.org S: Maintained F: fs/jbd*/ @@ -3311,48 +2854,41 @@ F: include/linux/ext*jbd*.h F: include/linux/jbd*.h K8TEMP HARDWARE MONITORING DRIVER -P: Rudolf Marek -M: r.marek@assembler.cz +M: Rudolf Marek L: lm-sensors@lm-sensors.org S: Maintained F: Documentation/hwmon/k8temp F: drivers/hwmon/k8temp.c KCONFIG -P: Roman Zippel -M: zippel@linux-m68k.org +M: Roman Zippel L: linux-kbuild@vger.kernel.org S: Maintained F: Documentation/kbuild/kconfig-language.txt F: scripts/kconfig/ KDUMP -P: Vivek Goyal -M: vgoyal@redhat.com -P: Haren Myneni -M: hbabu@us.ibm.com +M: Vivek Goyal +M: Haren Myneni L: kexec@lists.infradead.org W: http://lse.sourceforge.net/kdump/ S: Maintained F: Documentation/kdump/ KERNEL AUTOMOUNTER (AUTOFS) -P: H. Peter Anvin -M: hpa@zytor.com +M: "H. Peter Anvin" L: autofs@linux.kernel.org S: Odd Fixes F: fs/autofs/ KERNEL AUTOMOUNTER v4 (AUTOFS4) -P: Ian Kent -M: raven@themaw.net +M: Ian Kent L: autofs@linux.kernel.org S: Maintained F: fs/autofs4/ KERNEL BUILD -P: Sam Ravnborg -M: sam@ravnborg.org +M: Sam Ravnborg T: git git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-next.git T: git git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes.git L: linux-kbuild@vger.kernel.org @@ -3367,10 +2903,8 @@ W: http://www.kerneljanitors.org/ S: Odd fixes KERNEL NFSD, SUNRPC, AND LOCKD SERVERS -P: J. Bruce Fields -M: bfields@fieldses.org -P: Neil Brown -M: neilb@suse.de +M: "J. Bruce Fields" +M: Neil Brown L: linux-nfs@vger.kernel.org W: http://nfs.sourceforge.net/ S: Supported @@ -3383,8 +2917,7 @@ F: include/linux/lockd/ F: include/linux/sunrpc/ KERNEL VIRTUAL MACHINE (KVM) -P: Avi Kivity -M: avi@redhat.com +M: Avi Kivity L: kvm@vger.kernel.org W: http://kvm.qumranet.com S: Supported @@ -3395,8 +2928,7 @@ F: include/linux/kvm* F: virt/kvm/ KERNEL VIRTUAL MACHINE (KVM) FOR AMD-V -P: Joerg Roedel -M: joerg.roedel@amd.com +M: Joerg Roedel L: kvm@vger.kernel.org W: http://kvm.qumranet.com S: Supported @@ -3405,8 +2937,7 @@ F: arch/x86/kvm/kvm_svm.h F: arch/x86/kvm/svm.c KERNEL VIRTUAL MACHINE (KVM) FOR POWERPC -P: Hollis Blanchard -M: hollisb@us.ibm.com +M: Hollis Blanchard L: kvm-ppc@vger.kernel.org W: http://kvm.qumranet.com S: Supported @@ -3414,8 +2945,7 @@ F: arch/powerpc/include/asm/kvm* F: arch/powerpc/kvm/ KERNEL VIRTUAL MACHINE For Itanium (KVM/IA64) -P: Xiantao Zhang -M: xiantao.zhang@intel.com +M: Xiantao Zhang L: kvm-ia64@vger.kernel.org W: http://kvm.qumranet.com S: Supported @@ -3424,10 +2954,8 @@ F: arch/ia64/include/asm/kvm* F: arch/ia64/kvm/ KERNEL VIRTUAL MACHINE for s390 (KVM/s390) -P: Carsten Otte -M: cotte@de.ibm.com -P: Christian Borntraeger -M: borntraeger@de.ibm.com +M: Carsten Otte +M: Christian Borntraeger M: linux390@de.ibm.com L: linux-s390@vger.kernel.org W: http://www.ibm.com/developerworks/linux/linux390/ @@ -3437,8 +2965,7 @@ F: arch/s390/include/asm/kvm* F: arch/s390/kvm/ KEXEC -P: Eric Biederman -M: ebiederm@xmission.com +M: Eric Biederman W: http://ftp.kernel.org/pub/linux/kernel/people/horms/kexec-tools/ L: kexec@lists.infradead.org S: Maintained @@ -3446,8 +2973,7 @@ F: include/linux/kexec.h F: kernel/kexec.c KGDB -P: Jason Wessel -M: jason.wessel@windriver.com +M: Jason Wessel L: kgdb-bugreport@lists.sourceforge.net S: Maintained F: Documentation/DocBook/kgdb.tmpl @@ -3457,15 +2983,13 @@ F: include/linux/kgdb.h F: kernel/kgdb.c KMEMCHECK -P: Vegard Nossum -M: vegardno@ifi.uio.no +M: Vegard Nossum P Pekka Enberg M: penberg@cs.helsinki.fi S: Maintained KMEMLEAK -P: Catalin Marinas -M: catalin.marinas@arm.com +M: Catalin Marinas S: Maintained F: Documentation/kmemleak.txt F: include/linux/kmemleak.h @@ -3473,30 +2997,24 @@ F: mm/kmemleak.c F: mm/kmemleak-test.c KMEMTRACE -P: Eduard - Gabriel Munteanu -M: eduard.munteanu@linux360.ro +M: Eduard - Gabriel Munteanu S: Maintained F: Documentation/trace/kmemtrace.txt F: include/linux/kmemtrace.h F: kernel/trace/kmemtrace.c KPROBES -P: Ananth N Mavinakayanahalli -M: ananth@in.ibm.com -P: Anil S Keshavamurthy -M: anil.s.keshavamurthy@intel.com -P: David S. Miller -M: davem@davemloft.net -P: Masami Hiramatsu -M: mhiramat@redhat.com +M: Ananth N Mavinakayanahalli +M: Anil S Keshavamurthy +M: "David S. Miller" +M: Masami Hiramatsu S: Maintained F: Documentation/kprobes.txt F: include/linux/kprobes.h F: kernel/kprobes.c KS0108 LCD CONTROLLER DRIVER -P: Miguel Ojeda Sandonis -M: miguel.ojeda.sandonis@gmail.com +M: Miguel Ojeda Sandonis W: http://miguelojeda.es/auxdisplay.htm W: http://jair.lab.fi.uva.es/~migojed/auxdisplay.htm S: Maintained @@ -3512,31 +3030,27 @@ F: include/*/lapb.h F: net/lapb/ LASI 53c700 driver for PARISC -P: James E.J. Bottomley -M: James.Bottomley@HansenPartnership.com +M: "James E.J. Bottomley" L: linux-scsi@vger.kernel.org S: Maintained F: Documentation/scsi/53c700.txt F: drivers/scsi/53c700* LED SUBSYSTEM -P: Richard Purdie -M: rpurdie@rpsys.net +M: Richard Purdie S: Maintained F: drivers/leds/ F: include/linux/leds.h LEGO USB Tower driver -P: Juergen Stuber -M: starblue@users.sourceforge.net +M: Juergen Stuber L: legousb-devel@lists.sourceforge.net W: http://legousb.sourceforge.net/ S: Maintained F: drivers/usb/misc/legousbtower.c LGUEST -P: Rusty Russell -M: rusty@rustcorp.com.au +M: Rusty Russell L: lguest@ozlabs.org W: http://lguest.ozlabs.org/ S: Maintained @@ -3547,119 +3061,100 @@ F: include/linux/lguest*.h F: arch/x86/include/asm/lguest*.h LINUX FOR IBM pSERIES (RS/6000) -P: Paul Mackerras -M: paulus@au.ibm.com +M: Paul Mackerras W: http://www.ibm.com/linux/ltc/projects/ppc S: Supported LINUX FOR POWERPC (32-BIT AND 64-BIT) -P: Benjamin Herrenschmidt -M: benh@kernel.crashing.org -P: Paul Mackerras -M: paulus@samba.org +M: Benjamin Herrenschmidt +M: Paul Mackerras W: http://www.penguinppc.org/ L: linuxppc-dev@ozlabs.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc.git S: Supported LINUX FOR POWER MACINTOSH -P: Benjamin Herrenschmidt -M: benh@kernel.crashing.org +M: Benjamin Herrenschmidt W: http://www.penguinppc.org/ L: linuxppc-dev@ozlabs.org S: Maintained LINUX FOR POWERPC EMBEDDED MPC5XXX -P: Grant Likely -M: grant.likely@secretlab.ca +M: Grant Likely L: linuxppc-dev@ozlabs.org T: git git://git.secretlab.ca/git/linux-2.6.git S: Maintained LINUX FOR POWERPC EMBEDDED PPC4XX -P: Josh Boyer -M: jwboyer@linux.vnet.ibm.com -P: Matt Porter -M: mporter@kernel.crashing.org +M: Josh Boyer +M: Matt Porter W: http://www.penguinppc.org/ L: linuxppc-dev@ozlabs.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/jwboyer/powerpc-4xx.git S: Maintained LINUX FOR POWERPC EMBEDDED XILINX VIRTEX -P: Grant Likely -M: grant.likely@secretlab.ca +M: Grant Likely W: http://wiki.secretlab.ca/index.php/Linux_on_Xilinx_Virtex L: linuxppc-dev@ozlabs.org T: git git://git.secretlab.ca/git/linux-2.6.git S: Maintained LINUX FOR POWERPC EMBEDDED PPC8XX -P: Vitaly Bordug -M: vitb@kernel.crashing.org -P: Marcelo Tosatti -M: marcelo@kvack.org +M: Vitaly Bordug +M: Marcelo Tosatti W: http://www.penguinppc.org/ L: linuxppc-dev@ozlabs.org S: Maintained LINUX FOR POWERPC EMBEDDED PPC83XX AND PPC85XX -P: Kumar Gala -M: galak@kernel.crashing.org +M: Kumar Gala W: http://www.penguinppc.org/ L: linuxppc-dev@ozlabs.org S: Maintained LINUX FOR POWERPC PA SEMI PWRFICIENT -P: Olof Johansson -M: olof@lixom.net +M: Olof Johansson W: http://www.pasemi.com/ L: linuxppc-dev@ozlabs.org S: Supported LINUX SECURITY MODULE (LSM) FRAMEWORK -P: Chris Wright -M: chrisw@sous-sol.org +M: Chris Wright L: linux-security-module@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/chrisw/lsm-2.6.git S: Supported LLC (802.2) -P: Arnaldo Carvalho de Melo -M: acme@ghostprotocols.net +M: Arnaldo Carvalho de Melo S: Maintained F: include/linux/llc.h F: include/net/llc* F: net/llc/ LIS3LV02D ACCELEROMETER DRIVER -P: Eric Piel -M: eric.piel@tremplin-utc.net +M: Eric Piel S: Maintained F: Documentation/hwmon/lis3lv02d F: drivers/hwmon/lis3lv02d.* LM83 HARDWARE MONITOR DRIVER -P: Jean Delvare -M: khali@linux-fr.org +M: Jean Delvare L: lm-sensors@lm-sensors.org S: Maintained F: Documentation/hwmon/lm83 F: drivers/hwmon/lm83.c LM90 HARDWARE MONITOR DRIVER -P: Jean Delvare -M: khali@linux-fr.org +M: Jean Delvare L: lm-sensors@lm-sensors.org S: Maintained F: Documentation/hwmon/lm90 F: drivers/hwmon/lm90.c LOCKDEP AND LOCKSTAT -P: Peter Zijlstra -M: peterz@infradead.org -P: Ingo Molnar -M: mingo@redhat.com +M: Peter Zijlstra +M: Ingo Molnar T: git git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-lockdep.git S: Maintained F: Documentation/lockdep*.txt @@ -3668,8 +3163,7 @@ F: include/linux/lockdep.h F: kernel/lockdep* LOGICAL DISK MANAGER SUPPORT (LDM, Windows 2000/XP/Vista Dynamic Disks) -P: Richard Russon (FlatCap) -M: ldm@flatcap.org +M: "Richard Russon (FlatCap)" L: linux-ntfs-dev@lists.sourceforge.net W: http://www.linux-ntfs.org/content/view/19/37/ S: Maintained @@ -3677,8 +3171,7 @@ F: Documentation/ldm.txt F: fs/partitions/ldm.* LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI) -P: Eric Moore -M: Eric.Moore@lsi.com +M: Eric Moore M: support@lsi.com L: DL-MPTFusionLinux@lsi.com L: linux-scsi@vger.kernel.org @@ -3687,25 +3180,21 @@ S: Supported F: drivers/message/fusion/ LSILOGIC/SYMBIOS/NCR 53C8XX and 53C1010 PCI-SCSI drivers -P: Matthew Wilcox -M: matthew@wil.cx +M: Matthew Wilcox L: linux-scsi@vger.kernel.org S: Maintained F: drivers/scsi/sym53c8xx_2/ LTP (Linux Test Project) -P: Subrata Modak -M: subrata@linux.vnet.ibm.com -P: Mike Frysinger -M: vapier@gentoo.org +M: Subrata Modak +M: Mike Frysinger L: ltp-list@lists.sourceforge.net (subscribers-only) W: http://ltp.sourceforge.net/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/galak/ltp.git S: Maintained M32R ARCHITECTURE -P: Hirokazu Takata -M: takata@linux-m32r.org +M: Hirokazu Takata L: linux-m32r@ml.linux-m32r.org L: linux-m32r-ja@ml.linux-m32r.org (in Japanese) W: http://www.linux-m32r.org/ @@ -3713,10 +3202,8 @@ S: Maintained F: arch/m32r/ M68K ARCHITECTURE -P: Geert Uytterhoeven -M: geert@linux-m68k.org -P: Roman Zippel -M: zippel@linux-m68k.org +M: Geert Uytterhoeven +M: Roman Zippel L: linux-m68k@lists.linux-m68k.org W: http://www.linux-m68k.org/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k.git @@ -3725,23 +3212,20 @@ F: arch/m68k/ F: drivers/zorro/ M68K ON APPLE MACINTOSH -P: Joshua Thompson -M: funaho@jurai.org +M: Joshua Thompson W: http://www.mac.linux-m68k.org/ L: linux-m68k@lists.linux-m68k.org S: Maintained F: arch/m68k/mac/ M68K ON HP9000/300 -P: Philip Blundell -M: philb@gnu.org +M: Philip Blundell W: http://www.tazenda.demon.co.uk/phil/linux-hp S: Maintained F: arch/m68k/hp300/ MAC80211 -P: Johannes Berg -M: johannes@sipsolutions.net +M: Johannes Berg L: linux-wireless@vger.kernel.org W: http://linuxwireless.org/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6.git @@ -3751,10 +3235,8 @@ F: include/net/mac80211.h F: net/mac80211/ MAC80211 PID RATE CONTROL -P: Stefano Brivio -M: stefano.brivio@polimi.it -P: Mattias Nissler -M: mattias.nissler@gmx.de +M: Stefano Brivio +M: Mattias Nissler L: linux-wireless@vger.kernel.org W: http://linuxwireless.org/en/developers/Documentation/mac80211/RateControl/PID T: git git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6.git @@ -3762,67 +3244,57 @@ S: Maintained F: net/mac80211/rc80211_pid* MACVLAN DRIVER -P: Patrick McHardy -M: kaber@trash.net +M: Patrick McHardy L: netdev@vger.kernel.org S: Maintained F: drivers/net/macvlan.c F: include/linux/if_macvlan.h MAN-PAGES: MANUAL PAGES FOR LINUX -- Sections 2, 3, 4, 5, and 7 -P: Michael Kerrisk -M: mtk.manpages@gmail.com +M: Michael Kerrisk W: http://www.kernel.org/doc/man-pages L: linux-man@vger.kernel.org S: Maintained MARVELL LIBERTAS WIRELESS DRIVER -P: Dan Williams -M: dcbw@redhat.com +M: Dan Williams L: libertas-dev@lists.infradead.org S: Maintained F: drivers/net/wireless/libertas/ MARVELL MV643XX ETHERNET DRIVER -P: Lennert Buytenhek -M: buytenh@marvell.com +M: Lennert Buytenhek L: netdev@vger.kernel.org S: Supported F: drivers/net/mv643xx_eth.* F: include/linux/mv643xx.h MARVELL SOC MMC/SD/SDIO CONTROLLER DRIVER -P: Nicolas Pitre -M: nico@cam.org +M: Nicolas Pitre S: Maintained MARVELL YUKON / SYSKONNECT DRIVER -P: Mirko Lindner -M: mlindner@syskonnect.de -P: Ralph Roesler -M: rroesler@syskonnect.de +M: Mirko Lindner +M: Ralph Roesler W: http://www.syskonnect.com S: Supported MATROX FRAMEBUFFER DRIVER -P: Petr Vandrovec -M: vandrove@vc.cvut.cz +M: Petr Vandrovec L: linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers) S: Maintained F: drivers/video/matrox/matroxfb_* F: include/linux/matroxfb.h MAX6650 HARDWARE MONITOR AND FAN CONTROLLER DRIVER -P: Hans J. Koch -M: hjk@linutronix.de +M: "Hans J. Koch" L: lm-sensors@lm-sensors.org S: Maintained F: Documentation/hwmon/max6650 F: drivers/hwmon/max6650.c MEDIA INPUT INFRASTRUCTURE (V4L/DVB) -P: Mauro Carvalho Chehab -M: mchehab@infradead.org +M: Mauro Carvalho Chehab P: LinuxTV.org Project L: linux-media@vger.kernel.org W: http://linuxtv.org @@ -3836,8 +3308,7 @@ F: include/linux/dvb/ F: include/linux/videodev*.h MEGARAID SCSI DRIVERS -P: Neela Syam Kolli -M: megaraidlinux@lsi.com +M: Neela Syam Kolli L: linux-scsi@vger.kernel.org W: http://megaraid.lsilogic.com S: Maintained @@ -3853,19 +3324,15 @@ F: include/linux/mm.h F: mm/ MEMORY RESOURCE CONTROLLER -P: Balbir Singh -M: balbir@linux.vnet.ibm.com -P: Pavel Emelyanov -M: xemul@openvz.org -P: KAMEZAWA Hiroyuki -M: kamezawa.hiroyu@jp.fujitsu.com +M: Balbir Singh +M: Pavel Emelyanov +M: KAMEZAWA Hiroyuki L: linux-mm@kvack.org S: Maintained F: mm/memcontrol.c MEMORY TECHNOLOGY DEVICES (MTD) -P: David Woodhouse -M: dwmw2@infradead.org +M: David Woodhouse W: http://www.linux-mtd.infradead.org/ L: linux-mtd@lists.infradead.org T: git git://git.infradead.org/mtd-2.6.git @@ -3875,8 +3342,7 @@ F: include/linux/mtd/ F: include/mtd/ MICROBLAZE ARCHITECTURE -P: Michal Simek -M: monstr@monstr.eu +M: Michal Simek L: microblaze-uclinux@itee.uq.edu.au W: http://www.monstr.eu/fdt/ T: git git://git.monstr.eu/linux-2.6-microblaze.git @@ -3884,14 +3350,12 @@ S: Supported F: arch/microblaze/ MICROTEK X6 SCANNER -P: Oliver Neukum -M: oliver@neukum.name +M: Oliver Neukum S: Maintained F: drivers/usb/image/microtek.* MIPS -P: Ralf Baechle -M: ralf@linux-mips.org +M: Ralf Baechle W: http://www.linux-mips.org/ L: linux-mips@linux-mips.org T: git git://git.linux-mips.org/pub/scm/linux.git @@ -3900,8 +3364,7 @@ F: Documentation/mips/ F: arch/mips/ MISCELLANEOUS MCA-SUPPORT -P: James Bottomley -M: James.Bottomley@HansenPartnership.com +M: James Bottomley S: Maintained F: Documentation/ia64/mca.txt F: Documentation/mca.txt @@ -3909,15 +3372,13 @@ F: drivers/mca/ F: include/linux/mca* MODULE SUPPORT -P: Rusty Russell -M: rusty@rustcorp.com.au +M: Rusty Russell S: Maintained F: include/linux/module.h F: kernel/module.c MOTION EYE VAIO PICTUREBOOK CAMERA DRIVER -P: Stelian Pop -M: stelian@popies.net +M: Stelian Pop W: http://popies.net/meye/ S: Maintained F: Documentation/video4linux/meye.txt @@ -3925,135 +3386,112 @@ F: drivers/media/video/meye.* F: include/linux/meye.h MOTOROLA IMX MMC/SD HOST CONTROLLER INTERFACE DRIVER -P: Pavel Pisa -M: ppisa@pikron.com +M: Pavel Pisa L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained F: drivers/mmc/host/imxmmc.* MOUSE AND MISC DEVICES [GENERAL] -P: Alessandro Rubini -M: rubini@ipvvis.unipv.it +M: Alessandro Rubini S: Maintained F: drivers/input/mouse/ F: include/linux/gpio_mouse.h MOXA SMARTIO/INDUSTIO/INTELLIO SERIAL CARD -P: Jiri Slaby -M: jirislaby@gmail.com +M: Jiri Slaby S: Maintained F: Documentation/serial/moxa-smartio F: drivers/char/mxser.* MSI LAPTOP SUPPORT -P: Lennart Poettering -M: mzxreary@0pointer.de +M: Lennart Poettering W: https://tango.0pointer.de/mailman/listinfo/s270-linux W: http://0pointer.de/lennart/tchibo.html S: Maintained F: drivers/platform/x86/msi-laptop.c MULTIFUNCTION DEVICES (MFD) -P: Samuel Ortiz -M: sameo@linux.intel.com +M: Samuel Ortiz T: git git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6.git S: Supported F: drivers/mfd/ MULTIMEDIA CARD (MMC), SECURE DIGITAL (SD) AND SDIO SUBSYSTEM -P: Pierre Ossman -M: pierre@ossman.eu +M: Pierre Ossman S: Maintained F: drivers/mmc/ F: include/linux/mmc/ MULTIMEDIA CARD (MMC) ETC. OVER SPI -P: David Brownell -M: dbrownell@users.sourceforge.net +M: David Brownell S: Odd Fixes F: drivers/mmc/host/mmc_spi.c F: include/linux/spi/mmc_spi.h MULTISOUND SOUND DRIVER -P: Andrew Veliath -M: andrewtv@usa.net +M: Andrew Veliath S: Maintained F: Documentation/sound/oss/MultiSound F: sound/oss/msnd* MULTITECH MULTIPORT CARD (ISICOM) -P: Jiri Slaby -M: jirislaby@gmail.com +M: Jiri Slaby S: Maintained F: drivers/char/isicom.c F: include/linux/isicom.h MUSB MULTIPOINT HIGH SPEED DUAL-ROLE CONTROLLER -P: Felipe Balbi -M: felipe.balbi@nokia.com +M: Felipe Balbi L: linux-usb@vger.kernel.org T: git git://gitorious.org/musb/mainline.git S: Maintained F: drivers/usb/musb/ MYRICOM MYRI-10G 10GbE DRIVER (MYRI10GE) -P: Andrew Gallatin -M: gallatin@myri.com -P: Brice Goglin -M: brice@myri.com +M: Andrew Gallatin +M: Brice Goglin L: netdev@vger.kernel.org W: http://www.myri.com/scs/download-Myri10GE.html S: Supported F: drivers/net/myri10ge/ NATSEMI ETHERNET DRIVER (DP8381x) -P: Tim Hockin -M: thockin@hockin.org +M: Tim Hockin S: Maintained F: drivers/net/natsemi.c NCP FILESYSTEM -P: Petr Vandrovec -M: vandrove@vc.cvut.cz +M: Petr Vandrovec L: linware@sh.cvut.cz S: Maintained F: fs/ncpfs/ NCR DUAL 700 SCSI DRIVER (MICROCHANNEL) -P: James E.J. Bottomley -M: James.Bottomley@HansenPartnership.com +M: "James E.J. Bottomley" L: linux-scsi@vger.kernel.org S: Maintained F: drivers/scsi/NCR_D700.* NETEFFECT IWARP RNIC DRIVER (IW_NES) -P: Faisal Latif -M: faisal.latif@intel.com -P: Chien Tung -M: chien.tin.tung@intel.com +M: Faisal Latif +M: Chien Tung L: general@lists.openfabrics.org W: http://www.neteffect.com S: Supported F: drivers/infiniband/hw/nes/ NETEM NETWORK EMULATOR -P: Stephen Hemminger -M: shemminger@linux-foundation.org +M: Stephen Hemminger L: netem@lists.linux-foundation.org S: Maintained F: net/sched/sch_netem.c NETERION (S2IO) 10GbE DRIVER (xframe/vxge) -P: Ramkrishna Vepa -M: ram.vepa@neterion.com -P: Rastapur Santosh -M: santosh.rastapur@neterion.com -P: Sivakumar Subramani -M: sivakumar.subramani@neterion.com -P: Sreenivasa Honnur -M: sreenivasa.honnur@neterion.com -P: Anil Murthy -M: anil.murthy@neterion.com +M: Ramkrishna Vepa +M: Rastapur Santosh +M: Sivakumar Subramani +M: Sreenivasa Honnur +M: Anil Murthy L: netdev@vger.kernel.org W: http://trac.neterion.com/cgi-bin/trac.cgi/wiki/Linux?Anonymous W: http://trac.neterion.com/cgi-bin/trac.cgi/wiki/X3100Linux?Anonymous @@ -4067,8 +3505,7 @@ P: Marc Boucher P: James Morris P: Harald Welte P: Jozsef Kadlecsik -P: Patrick McHardy -M: kaber@trash.net +M: Patrick McHardy L: netfilter-devel@vger.kernel.org L: netfilter@vger.kernel.org L: coreteam@netfilter.org @@ -4084,8 +3521,7 @@ F: net/*/netfilter/ F: net/netfilter/ NETLABEL -P: Paul Moore -M: paul.moore@hp.com +M: Paul Moore W: http://netlabel.sf.net L: netdev@vger.kernel.org S: Supported @@ -4094,8 +3530,7 @@ F: include/net/netlabel.h F: net/netlabel/ NETROM NETWORK LAYER -P: Ralf Baechle -M: ralf@linux-mips.org +M: Ralf Baechle L: linux-hams@vger.kernel.org W: http://www.linux-ax25.org/ S: Maintained @@ -4104,16 +3539,14 @@ F: include/net/netrom.h F: net/netrom/ NETWORK BLOCK DEVICE (NBD) -P: Paul Clements -M: Paul.Clements@steeleye.com +M: Paul Clements S: Maintained F: Documentation/blockdev/nbd.txt F: drivers/block/nbd.c F: include/linux/nbd.h NETWORKING [GENERAL] -P: David S. Miller -M: davem@davemloft.net +M: "David S. Miller" L: netdev@vger.kernel.org W: http://www.linuxfoundation.org/en/Net T: git git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.git @@ -4122,18 +3555,12 @@ F: net/ F: include/net/ NETWORKING [IPv4/IPv6] -P: David S. Miller -M: davem@davemloft.net -P: Alexey Kuznetsov -M: kuznet@ms2.inr.ac.ru -P: Pekka Savola (ipv6) -M: pekkas@netcore.fi -P: James Morris -M: jmorris@namei.org -P: Hideaki YOSHIFUJI -M: yoshfuji@linux-ipv6.org -P: Patrick McHardy -M: kaber@trash.net +M: "David S. Miller" +M: Alexey Kuznetsov +M: "Pekka Savola (ipv6)" +M: James Morris +M: Hideaki YOSHIFUJI +M: Patrick McHardy L: netdev@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.git S: Maintained @@ -4142,14 +3569,12 @@ F: net/ipv6/ F: include/net/ip* NETWORKING [LABELED] (NetLabel, CIPSO, Labeled IPsec, SECMARK) -P: Paul Moore -M: paul.moore@hp.com +M: Paul Moore L: netdev@vger.kernel.org S: Maintained NETWORKING [WIRELESS] -P: John W. Linville -M: linville@tuxdriver.com +M: "John W. Linville" L: linux-wireless@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6.git S: Maintained @@ -4165,16 +3590,14 @@ S: Odd Fixes F: drivers/net/ NETXEN (1/10) GbE SUPPORT -P: Dhananjay Phadke -M: dhananjay@netxen.com +M: Dhananjay Phadke L: netdev@vger.kernel.org W: http://www.netxen.com S: Supported F: drivers/net/netxen/ NFS, SUNRPC, AND LOCKD CLIENTS -P: Trond Myklebust -M: Trond.Myklebust@netapp.com +M: Trond Myklebust L: linux-nfs@vger.kernel.org W: http://client.linux-nfs.org T: git git://git.linux-nfs.org/pub/linux/nfs-2.6.git @@ -4188,17 +3611,14 @@ F: include/linux/nfs* F: include/linux/sunrpc/ NI5010 NETWORK DRIVER -P: Jan-Pascal van Best -M: janpascal@vanbest.org -P: Andreas Mohr -M: andi@lisas.de +M: Jan-Pascal van Best +M: Andreas Mohr L: netdev@vger.kernel.org S: Maintained F: drivers/net/ni5010.* NILFS2 FILESYSTEM -P: KONISHI Ryusuke -M: konishi.ryusuke@lab.ntt.co.jp +M: KONISHI Ryusuke L: users@nilfs.org W: http://www.nilfs.org/en/ S: Supported @@ -4207,26 +3627,22 @@ F: fs/nilfs2/ F: include/linux/nilfs2_fs.h NINJA SCSI-3 / NINJA SCSI-32Bi (16bit/CardBus) PCMCIA SCSI HOST ADAPTER DRIVER -P: YOKOTA Hiroshi -M: yokota@netlab.is.tsukuba.ac.jp +M: YOKOTA Hiroshi W: http://www.netlab.is.tsukuba.ac.jp/~yokota/izumi/ninja/ S: Maintained F: Documentation/scsi/NinjaSCSI.txt F: drivers/scsi/pcmcia/nsp_* NINJA SCSI-32Bi/UDE PCI/CARDBUS SCSI HOST ADAPTER DRIVER -P: GOTO Masanori -M: gotom@debian.or.jp -P: YOKOTA Hiroshi -M: yokota@netlab.is.tsukuba.ac.jp +M: GOTO Masanori +M: YOKOTA Hiroshi W: http://www.netlab.is.tsukuba.ac.jp/~yokota/izumi/ninja/ S: Maintained F: Documentation/scsi/NinjaSCSI.txt F: drivers/scsi/nsp32* NTFS FILESYSTEM -P: Anton Altaparmakov -M: aia21@cantab.net +M: Anton Altaparmakov L: linux-ntfs-dev@lists.sourceforge.net W: http://www.linux-ntfs.org/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/aia21/ntfs-2.6.git @@ -4235,16 +3651,14 @@ F: Documentation/filesystems/ntfs.txt F: fs/ntfs/ NVIDIA (rivafb and nvidiafb) FRAMEBUFFER DRIVER -P: Antonino Daplas -M: adaplas@gmail.com +M: Antonino Daplas L: linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers) S: Maintained F: drivers/video/riva/ F: drivers/video/nvidia/ OMAP SUPPORT -P: Tony Lindgren -M: tony@atomide.com +M: "Tony Lindgren " L: linux-omap@vger.kernel.org W: http://www.muru.com/linux/omap/ W: http://linux.omap.com/ @@ -4253,97 +3667,83 @@ S: Maintained F: arch/arm/*omap* OMAP CLOCK FRAMEWORK SUPPORT -P: Paul Walmsley -M: paul@pwsan.com +M: Paul Walmsley L: linux-omap@vger.kernel.org S: Maintained F: arch/arm/*omap*/*clock* OMAP POWER MANAGEMENT SUPPORT -P: Kevin Hilman -M: khilman@deeprootsystems.com +M: Kevin Hilman L: linux-omap@vger.kernel.org S: Maintained F: arch/arm/*omap*/*pm* OMAP AUDIO SUPPORT -P: Jarkko Nikula -M: jhnikula@gmail.com +M: Jarkko Nikula L: alsa-devel@alsa-project.org (subscribers-only) L: linux-omap@vger.kernel.org S: Maintained F: sound/soc/omap/ OMAP FRAMEBUFFER SUPPORT -P: Imre Deak -M: imre.deak@nokia.com +M: Imre Deak L: linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers) L: linux-omap@vger.kernel.org S: Maintained F: drivers/video/omap/ OMAP MMC SUPPORT -P: Jarkko Lavinen -M: jarkko.lavinen@nokia.com +M: Jarkko Lavinen L: linux-omap@vger.kernel.org S: Maintained F: drivers/mmc/host/*omap* OMAP RANDOM NUMBER GENERATOR SUPPORT -P: Deepak Saxena -M: dsaxena@plexity.net +M: Deepak Saxena S: Maintained F: drivers/char/hw_random/omap-rng.c OMAP USB SUPPORT -P: Felipe Balbi -M: felipe.balbi@nokia.com -P: David Brownell -M: dbrownell@users.sourceforge.net +M: Felipe Balbi +M: David Brownell L: linux-usb@vger.kernel.org L: linux-omap@vger.kernel.org S: Maintained OMFS FILESYSTEM -P: Bob Copeland -M: me@bobcopeland.com +M: Bob Copeland L: linux-karma-devel@lists.sourceforge.net S: Maintained F: Documentation/filesystems/omfs.txt F: fs/omfs/ OMNIKEY CARDMAN 4000 DRIVER -P: Harald Welte -M: laforge@gnumonks.org +M: Harald Welte S: Maintained F: drivers/char/pcmcia/cm4000_cs.c F: include/linux/cm4000_cs.h OMNIKEY CARDMAN 4040 DRIVER -P: Harald Welte -M: laforge@gnumonks.org +M: Harald Welte S: Maintained F: drivers/char/pcmcia/cm4040_cs.* OMNIVISION OV7670 SENSOR DRIVER -P: Jonathan Corbet -M: corbet@lwn.net +M: Jonathan Corbet L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git S: Maintained F: drivers/media/video/ov7670.c ONENAND FLASH DRIVER -P: Kyungmin Park -M: kyungmin.park@samsung.com +M: Kyungmin Park L: linux-mtd@lists.infradead.org S: Maintained F: drivers/mtd/onenand/ F: include/linux/mtd/onenand*.h ONSTREAM SCSI TAPE DRIVER -P: Willem Riede -M: osst@riede.org +M: Willem Riede L: osst-users@lists.sourceforge.net L: linux-scsi@vger.kernel.org S: Maintained @@ -4351,16 +3751,14 @@ F: drivers/scsi/osst* F: drivers/scsi/st* OPENCORES I2C BUS DRIVER -P: Peter Korsgaard -M: jacmet@sunsite.dk +M: Peter Korsgaard L: linux-i2c@vger.kernel.org S: Maintained F: Documentation/i2c/busses/i2c-ocores F: drivers/i2c/busses/i2c-ocores.c OPROFILE -P: Robert Richter -M: robert.richter@amd.com +M: Robert Richter L: oprofile-list@lists.sf.net S: Maintained F: arch/*/oprofile/ @@ -4368,10 +3766,8 @@ F: drivers/oprofile/ F: include/linux/oprofile.h ORACLE CLUSTER FILESYSTEM 2 (OCFS2) -P: Mark Fasheh -M: mfasheh@suse.com -P: Joel Becker -M: joel.becker@oracle.com +M: Mark Fasheh +M: Joel Becker L: ocfs2-devel@oss.oracle.com (moderated for non-subscribers) W: http://oss.oracle.com/projects/ocfs2/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2.git @@ -4381,10 +3777,8 @@ F: Documentation/filesystems/dlmfs.txt F: fs/ocfs2/ ORINOCO DRIVER -P: Pavel Roskin -M: proski@gnu.org -P: David Gibson -M: hermes@gibson.dropbear.id.au +M: Pavel Roskin +M: David Gibson L: linux-wireless@vger.kernel.org L: orinoco-users@lists.sourceforge.net L: orinoco-devel@lists.sourceforge.net @@ -4393,10 +3787,8 @@ S: Maintained F: drivers/net/wireless/orinoco/ OSD LIBRARY and FILESYSTEM -P: Boaz Harrosh -M: bharrosh@panasas.com -P: Benny Halevy -M: bhalevy@panasas.com +M: Boaz Harrosh +M: Benny Halevy L: osd-dev@open-osd.org W: http://open-osd.org T: git git://git.open-osd.org/open-osd.git @@ -4406,8 +3798,7 @@ F: drivers/include/scsi/osd_* F: fs/exofs/ P54 WIRELESS DRIVER -P: Michael Wu -M: flamingice@sourmilk.net +M: Michael Wu L: linux-wireless@vger.kernel.org W: http://prism54.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mwu/mac80211-drivers.git @@ -4415,30 +3806,25 @@ S: Maintained F: drivers/net/wireless/p54/ PA SEMI ETHERNET DRIVER -P: Olof Johansson -M: olof@lixom.net +M: Olof Johansson L: netdev@vger.kernel.org S: Maintained F: drivers/net/pasemi_mac.* PA SEMI SMBUS DRIVER -P: Olof Johansson -M: olof@lixom.net +M: Olof Johansson L: linux-i2c@vger.kernel.org S: Maintained F: drivers/i2c/busses/i2c-pasemi.c PANASONIC LAPTOP ACPI EXTRAS DRIVER -P: Harald Welte -M: laforge@gnumonks.org +M: Harald Welte S: Maintained F: drivers/platform/x86/panasonic-laptop.c PANASONIC MN10300/AM33 PORT -P: David Howells -M: dhowells@redhat.com -P: Koichi Yasutake -M: yasutake.koichi@jp.panasonic.com +M: David Howells +M: Koichi Yasutake L: linux-am33-list@redhat.com (moderated for non-subscribers) W: ftp://ftp.redhat.com/pub/redhat/gnupro/AM33/ S: Maintained @@ -4454,14 +3840,10 @@ F: drivers/char/ppdev.c F: include/linux/ppdev.h PARAVIRT_OPS INTERFACE -P: Jeremy Fitzhardinge -M: jeremy@xensource.com -P: Chris Wright -M: chrisw@sous-sol.org -P: Alok Kataria -M: akataria@vmware.com -P: Rusty Russell -M: rusty@rustcorp.com.au +M: Jeremy Fitzhardinge +M: Chris Wright +M: Alok Kataria +M: Rusty Russell L: virtualization@lists.osdl.org S: Supported F: Documentation/ia64/paravirt_ops.txt @@ -4469,8 +3851,7 @@ F: arch/*/kernel/paravirt* F: arch/*/include/asm/paravirt.h PARIDE DRIVERS FOR PARALLEL PORT IDE DEVICES -P: Tim Waugh -M: tim@cyberelk.net +M: Tim Waugh L: linux-parport@lists.infradead.org (subscribers-only) W: http://www.torque.net/linux-pp.html S: Maintained @@ -4478,10 +3859,8 @@ F: Documentation/blockdev/paride.txt F: drivers/block/paride/ PARISC ARCHITECTURE -P: Kyle McMartin -M: kyle@mcmartin.ca -P: Helge Deller -M: deller@gmx.de +M: Kyle McMartin +M: Helge Deller L: linux-parisc@vger.kernel.org W: http://www.parisc-linux.org/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6.git @@ -4490,37 +3869,32 @@ F: arch/parisc/ F: drivers/parisc/ PC87360 HARDWARE MONITORING DRIVER -P: Jim Cromie -M: jim.cromie@gmail.com +M: Jim Cromie L: lm-sensors@lm-sensors.org S: Maintained F: Documentation/hwmon/pc87360 F: drivers/hwmon/pc87360.c PC8736x GPIO DRIVER -P: Jim Cromie -M: jim.cromie@gmail.com +M: Jim Cromie S: Maintained F: drivers/char/pc8736x_gpio.c PCA9532 LED DRIVER -P: Riku Voipio -M: riku.voipio@iki.fi +M: Riku Voipio S: Maintained F: drivers/leds/leds-pca9532.c F: include/linux/leds-pca9532.h PCI ERROR RECOVERY -P: Linas Vepstas -M: linas@austin.ibm.com +M: Linas Vepstas L: linux-pci@vger.kernel.org S: Supported F: Documentation/PCI/pci-error-recovery.txt F: Documentation/powerpc/eeh-pci-error-recovery.txt PCI SUBSYSTEM -P: Jesse Barnes -M: jbarnes@virtuousgeek.org +M: Jesse Barnes L: linux-pci@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6.git S: Supported @@ -4529,8 +3903,7 @@ F: drivers/pci/ F: include/linux/pci* PCIE HOTPLUG DRIVER -P: Kristen Carlson Accardi -M: kristen.c.accardi@intel.com +M: Kristen Carlson Accardi L: linux-pci@vger.kernel.org S: Supported F: drivers/pci/pcie/ @@ -4546,113 +3919,94 @@ F: drivers/pcmcia/ F: include/pcmcia/ PCNET32 NETWORK DRIVER -P: Don Fry -M: pcnet32@verizon.net +M: Don Fry L: netdev@vger.kernel.org S: Maintained F: drivers/net/pcnet32.c PER-TASK DELAY ACCOUNTING -P: Balbir Singh -M: balbir@linux.vnet.ibm.com +M: Balbir Singh S: Maintained F: include/linux/delayacct.h F: kernel/delayacct.c PERFORMANCE COUNTER SUBSYSTEM -P: Peter Zijlstra -M: a.p.zijlstra@chello.nl -P: Paul Mackerras -M: paulus@samba.org -P: Ingo Molnar -M: mingo@elte.hu +M: Peter Zijlstra +M: Paul Mackerras +M: Ingo Molnar S: Supported PERSONALITY HANDLING -P: Christoph Hellwig -M: hch@infradead.org +M: Christoph Hellwig L: linux-abi-devel@lists.sourceforge.net S: Maintained F: include/linux/personality.h PHRAM MTD DRIVER -P: Joern Engel -M: joern@lazybastard.org +M: Joern Engel L: linux-mtd@lists.infradead.org S: Maintained F: drivers/mtd/devices/phram.c PKTCDVD DRIVER -P: Peter Osterlund -M: petero2@telia.com +M: Peter Osterlund S: Maintained F: drivers/block/pktcdvd.c F: include/linux/pktcdvd.h POSIX CLOCKS and TIMERS -P: Thomas Gleixner -M: tglx@linutronix.de +M: Thomas Gleixner S: Supported F: fs/timerfd.c F: include/linux/timer* F: kernel/*timer* POWER SUPPLY CLASS/SUBSYSTEM and DRIVERS -P: Anton Vorontsov -M: cbou@mail.ru -P: David Woodhouse -M: dwmw2@infradead.org +M: Anton Vorontsov +M: David Woodhouse T: git git://git.infradead.org/battery-2.6.git S: Maintained F: include/linux/power_supply.h F: drivers/power/power_supply* PNP SUPPORT -P: Adam Belay -M: abelay@mit.edu -P: Bjorn Helgaas -M: bjorn.helgaas@hp.com +M: Adam Belay +M: Bjorn Helgaas S: Maintained F: drivers/pnp/ PNXxxxx I2C DRIVER -P: Vitaly Wool -M: vitalywool@gmail.com +M: Vitaly Wool L: linux-i2c@vger.kernel.org S: Maintained F: drivers/i2c/busses/i2c-pnx.c PPP PROTOCOL DRIVERS AND COMPRESSORS -P: Paul Mackerras -M: paulus@samba.org +M: Paul Mackerras L: linux-ppp@vger.kernel.org S: Maintained F: drivers/net/ppp_* PPP OVER ATM (RFC 2364) -P: Mitchell Blank Jr -M: mitch@sfgoth.com +M: Mitchell Blank Jr S: Maintained F: net/atm/pppoatm.c F: include/linux/atmppp.h PPP OVER ETHERNET -P: Michal Ostrowski -M: mostrows@earthlink.net +M: Michal Ostrowski S: Maintained F: drivers/net/pppoe.c F: drivers/net/pppox.c PPP OVER L2TP -P: James Chapman -M: jchapman@katalix.com +M: James Chapman S: Maintained F: drivers/net/pppol2tp.c F: include/linux/if_pppol2tp.h PPS SUPPORT -P: Rodolfo Giometti -M: giometti@enneenne.com +M: Rodolfo Giometti W: http://wiki.enneenne.com/index.php/LinuxPPS_support L: linuxpps@ml.enneenne.com (subscribers-only) S: Maintained @@ -4661,8 +4015,7 @@ F: drivers/pps/ F: include/linux/pps*.h PREEMPTIBLE KERNEL -P: Robert Love -M: rml@tech9.net +M: Robert Love L: kpreempt-tech@lists.sourceforge.net W: ftp://ftp.kernel.org/pub/linux/kernel/people/rml/preempt-kernel S: Supported @@ -4670,37 +4023,32 @@ F: Documentation/preempt-locking.txt F: include/linux/preempt.h PRISM54 WIRELESS DRIVER -P: Luis R. Rodriguez -M: mcgrof@gmail.com +M: "Luis R. Rodriguez" L: linux-wireless@vger.kernel.org W: http://prism54.org S: Maintained F: drivers/net/wireless/prism54/ PROMISE DC4030 CACHING DISK CONTROLLER DRIVER -P: Peter Denison -M: promise@pnd-pc.demon.co.uk +M: Peter Denison W: http://www.pnd-pc.demon.co.uk/promise/ S: Maintained PROMISE SATA TX2/TX4 CONTROLLER LIBATA DRIVER -P: Mikael Pettersson -M: mikpe@it.uu.se +M: Mikael Pettersson L: linux-ide@vger.kernel.org S: Maintained F: drivers/ata/sata_promise.* PS3 NETWORK SUPPORT -P: Geoff Levand -M: geoffrey.levand@am.sony.com +M: Geoff Levand L: netdev@vger.kernel.org L: cbe-oss-dev@ozlabs.org S: Supported F: drivers/net/ps3_gelic_net.* PS3 PLATFORM SUPPORT -P: Geoff Levand -M: geoffrey.levand@am.sony.com +M: Geoff Levand L: linuxppc-dev@ozlabs.org L: cbe-oss-dev@ozlabs.org S: Supported @@ -4715,16 +4063,13 @@ F: drivers/usb/host/*ps3.c F: sound/ppc/snd_ps3* PS3VRAM DRIVER -P: Jim Paris -M: jim@jtan.com +M: Jim Paris L: cbe-oss-dev@ozlabs.org S: Maintained PTRACE SUPPORT -P: Roland McGrath -M: roland@redhat.com -P: Oleg Nesterov -M: oleg@redhat.com +M: Roland McGrath +M: Oleg Nesterov S: Maintained F: include/asm-generic/syscall.h F: include/linux/ptrace.h @@ -4733,8 +4078,7 @@ F: include/linux/tracehook.h F: kernel/ptrace.c PVRUSB2 VIDEO4LINUX DRIVER -P: Mike Isely -M: isely@pobox.com +M: Mike Isely L: pvrusb2@isely.net (subscribers-only) L: linux-media@vger.kernel.org W: http://www.isely.net/pvrusb2/ @@ -4744,10 +4088,8 @@ F: Documentation/video4linux/README.pvrusb2 F: drivers/media/video/pvrusb2/ PXA2xx/PXA3xx SUPPORT -P: Eric Miao -M: eric.y.miao@gmail.com -P: Russell King -M: linux@arm.linux.org.uk +M: Eric Miao +M: Russell King L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained F: arch/arm/mach-pxa/ @@ -4759,17 +4101,14 @@ F: sound/arm/pxa* F: sound/soc/pxa PXA168 SUPPORT -P: Eric Miao -M: eric.y.miao@gmail.com -P: Jason Chagas -M: jason.chagas@marvell.com +M: Eric Miao +M: Jason Chagas L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) T: git git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6.git S: Maintained PXA910 SUPPORT -P: Eric Miao -M: eric.y.miao@gmail.com +M: Eric Miao L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) T: git git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6.git S: Maintained @@ -4778,14 +4117,12 @@ PXA MMCI DRIVER S: Orphan PXA RTC DRIVER -P: Robert Jarzmik -M: robert.jarzmik@free.fr +M: Robert Jarzmik L: rtc-linux@googlegroups.com S: Maintained QLOGIC QLA2XXX FC-SCSI DRIVER -P: Andrew Vasquez -M: andrew.vasquez@qlogic.com +M: Andrew Vasquez M: linux-driver@qlogic.com L: linux-scsi@vger.kernel.org S: Supported @@ -4793,8 +4130,7 @@ F: Documentation/scsi/LICENSE.qla2xxx F: drivers/scsi/qla2xxx/ QLOGIC QLA3XXX NETWORK DRIVER -P: Ron Mercer -M: ron.mercer@qlogic.com +M: Ron Mercer M: linux-driver@qlogic.com L: netdev@vger.kernel.org S: Supported @@ -4802,16 +4138,14 @@ F: Documentation/networking/LICENSE.qla3xxx F: drivers/net/qla3xxx.* QLOGIC QLGE 10Gb ETHERNET DRIVER -P: Ron Mercer -M: ron.mercer@qlogic.com +M: Ron Mercer M: linux-driver@qlogic.com L: netdev@vger.kernel.org S: Supported F: drivers/net/qlge/ QNX4 FILESYSTEM -P: Anders Larsen -M: al@alarsen.net +M: Anders Larsen W: http://www.alarsen.net/linux/qnx4fs/ S: Maintained F: fs/qnx4/ @@ -4819,16 +4153,14 @@ F: include/linux/qnx4_fs.h F: include/linux/qnxtypes.h RADEON FRAMEBUFFER DISPLAY DRIVER -P: Benjamin Herrenschmidt -M: benh@kernel.crashing.org +M: Benjamin Herrenschmidt L: linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers) S: Maintained F: drivers/video/aty/radeon* F: include/linux/radeonfb.h RAGE128 FRAMEBUFFER DISPLAY DRIVER -P: Paul Mackerras -M: paulus@samba.org +M: Paul Mackerras L: linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers) S: Maintained F: drivers/video/aty/aty128fb.c @@ -4843,64 +4175,53 @@ T: git git://git.kernel.org/pub/scm/linux/kernel/git/ivd/rt2x00.git F: drivers/net/wireless/rt2x00/ RAMDISK RAM BLOCK DEVICE DRIVER -P: Nick Piggin -M: npiggin@suse.de +M: Nick Piggin S: Maintained F: Documentation/blockdev/ramdisk.txt F: drivers/block/brd.c RANDOM NUMBER DRIVER -P: Matt Mackall -M: mpm@selenic.com +M: Matt Mackall S: Maintained F: drivers/char/random.c RAPIDIO SUBSYSTEM -P: Matt Porter -M: mporter@kernel.crashing.org +M: Matt Porter S: Maintained F: drivers/rapidio/ RAYLINK/WEBGEAR 802.11 WIRELESS LAN DRIVER -P: Corey Thomas -M: coreythomas@charter.net +M: Corey Thomas L: linux-wireless@vger.kernel.org S: Maintained F: drivers/net/wireless/ray* RCUTORTURE MODULE -P: Josh Triplett -M: josh@freedesktop.org -P: Paul E. McKenney -M: paulmck@linux.vnet.ibm.com +M: Josh Triplett +M: "Paul E. McKenney" S: Maintained F: Documentation/RCU/torture.txt F: kernel/rcutorture.c RDC R-321X SoC -P: Florian Fainelli -M: florian@openwrt.org +M: Florian Fainelli S: Maintained RDC R6040 FAST ETHERNET DRIVER -P: Florian Fainelli -M: florian@openwrt.org +M: Florian Fainelli L: netdev@vger.kernel.org S: Maintained F: drivers/net/r6040.c RDS - RELIABLE DATAGRAM SOCKETS -P: Andy Grover -M: andy.grover@oracle.com +M: Andy Grover L: rds-devel@oss.oracle.com (moderated for non-subscribers) S: Supported F: net/rds/ READ-COPY UPDATE (RCU) -P: Dipankar Sarma -M: dipankar@in.ibm.com -P: Paul E. McKenney -M: paulmck@linux.vnet.ibm.com +M: Dipankar Sarma +M: "Paul E. McKenney" W: http://www.rdrop.com/users/paulmck/rclock/ S: Supported F: Documentation/RCU/rcu.txt @@ -4910,16 +4231,14 @@ F: include/linux/srcu.h F: kernel/rcupdate.c REAL TIME CLOCK DRIVER -P: Paul Gortmaker -M: p_gortmaker@yahoo.com +M: Paul Gortmaker S: Maintained F: Documentation/rtc.txt F: drivers/rtc/ F: include/linux/rtc.h REAL TIME CLOCK (RTC) SUBSYSTEM -P: Alessandro Zummo -M: a.zummo@towertech.it +M: Alessandro Zummo L: rtc-linux@googlegroups.com S: Maintained F: Documentation/rtc.txt @@ -4932,8 +4251,7 @@ S: Supported F: fs/reiserfs/ RFKILL -P: Johannes Berg -M: johannes@sipsolutions.net +M: Johannes Berg L: linux-wireless@vger.kernel.org S: Maintained F Documentation/rfkill.txt @@ -4952,8 +4270,7 @@ F: Documentation/serial/rocket.txt F: drivers/char/rocket* ROSE NETWORK LAYER -P: Ralf Baechle -M: ralf@linux-mips.org +M: Ralf Baechle L: linux-hams@vger.kernel.org W: http://www.linux-ax25.org/ S: Maintained @@ -4962,8 +4279,7 @@ F: include/net/rose.h F: net/rose/ RTL8180 WIRELESS DRIVER -P: John W. Linville -M: linville@tuxdriver.com +M: "John W. Linville" L: linux-wireless@vger.kernel.org W: http://linuxwireless.org/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-testing.git @@ -4971,12 +4287,9 @@ S: Maintained F: drivers/net/wireless/rtl818* RTL8187 WIRELESS DRIVER -P: Herton Ronaldo Krzesinski -M: herton@mandriva.com.br -P: Hin-Tak Leung -M: htl10@users.sourceforge.net -P: Larry Finger -M: Larry.Finger@lwfinger.net +M: Herton Ronaldo Krzesinski +M: Hin-Tak Leung +M: Larry Finger L: linux-wireless@vger.kernel.org W: http://linuxwireless.org/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-testing.git @@ -4984,17 +4297,14 @@ S: Maintained F: drivers/net/wireless/rtl818x/rtl8187* S3 SAVAGE FRAMEBUFFER DRIVER -P: Antonino Daplas -M: adaplas@gmail.com +M: Antonino Daplas L: linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers) S: Maintained F: drivers/video/savage/ S390 -P: Martin Schwidefsky -M: schwidefsky@de.ibm.com -P: Heiko Carstens -M: heiko.carstens@de.ibm.com +M: Martin Schwidefsky +M: Heiko Carstens M: linux390@de.ibm.com L: linux-s390@vger.kernel.org W: http://www.ibm.com/developerworks/linux/linux390/ @@ -5002,10 +4312,8 @@ S: Supported F: arch/s390/ S390 NETWORK DRIVERS -P: Ursula Braun -M: ursula.braun@de.ibm.com -P: Frank Blaschka -M: blaschka@linux.vnet.ibm.com +M: Ursula Braun +M: Frank Blaschka M: linux390@de.ibm.com L: linux-s390@vger.kernel.org W: http://www.ibm.com/developerworks/linux/linux390/ @@ -5013,20 +4321,16 @@ S: Supported F: drivers/s390/net/ S390 ZCRYPT DRIVER -P: Felix Beck -M: felix.beck@de.ibm.com -P: Ralph Wuerthner -M: ralph.wuerthner@de.ibm.com +M: Felix Beck +M: Ralph Wuerthner M: linux390@de.ibm.com L: linux-s390@vger.kernel.org S: Supported F: drivers/s390/crypto/ S390 ZFCP DRIVER -P: Christof Schmitt -M: christof.schmitt@de.ibm.com -P: Martin Peschke -M: mp3@de.ibm.com +M: Christof Schmitt +M: Martin Peschke M: linux390@de.ibm.com L: linux-s390@vger.kernel.org W: http://www.ibm.com/developerworks/linux/linux390/ @@ -5035,8 +4339,7 @@ F: Documentation/s390/zfcpdump.txt F: drivers/s390/scsi/zfcp_* S390 IUCV NETWORK LAYER -P: Ursula Braun -M: ursula.braun@de.ibm.com +M: Ursula Braun M: linux390@de.ibm.com L: linux-s390@vger.kernel.org W: http://www.ibm.com/developerworks/linux/linux390/ @@ -5046,15 +4349,13 @@ F: include/net/iucv/ F: net/iucv/ S3C24XX SD/MMC Driver -P: Ben Dooks -M: ben-linux@fluff.org +M: Ben Dooks L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Supported F: drivers/mmc/host/s3cmci.* SAA7146 VIDEO4LINUX-2 DRIVER -P: Michael Hunold -M: michael@mihu.de +M: Michael Hunold L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git W: http://www.mihu.de/linux/saa7146 @@ -5064,31 +4365,26 @@ F: drivers/media/video/*7146* F: include/media/*7146* SC1200 WDT DRIVER -P: Zwane Mwaikambo -M: zwane@arm.linux.org.uk +M: Zwane Mwaikambo S: Maintained F: drivers/watchdog/sc1200wdt.c SCHEDULER -P: Ingo Molnar -M: mingo@elte.hu -P: Peter Zijlstra -M: peterz@infradead.org +M: Ingo Molnar +M: Peter Zijlstra S: Maintained F: kernel/sched* F: include/linux/sched.h SCSI CDROM DRIVER -P: Jens Axboe -M: axboe@kernel.dk +M: Jens Axboe L: linux-scsi@vger.kernel.org W: http://www.kernel.dk S: Maintained F: drivers/scsi/sr* SCSI SG DRIVER -P: Doug Gilbert -M: dgilbert@interlog.com +M: Doug Gilbert L: linux-scsi@vger.kernel.org W: http://www.torque.net/sg S: Maintained @@ -5096,8 +4392,7 @@ F: drivers/scsi/sg.c F: include/scsi/sg.h SCSI SUBSYSTEM -P: James E.J. Bottomley -M: James.Bottomley@HansenPartnership.com +M: "James E.J. Bottomley" L: linux-scsi@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6.git T: git git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6.git @@ -5107,18 +4402,15 @@ F: drivers/scsi/ F: include/scsi/ SCSI TAPE DRIVER -P: Kai Mäkisara -M: Kai.Makisara@kolumbus.fi +M: Kai Mäkisara L: linux-scsi@vger.kernel.org S: Maintained F: Documentation/scsi/st.txt F: drivers/scsi/st* SCTP PROTOCOL -P: Vlad Yasevich -M: vladislav.yasevich@hp.com -P: Sridhar Samudrala -M: sri@us.ibm.com +M: Vlad Yasevich +M: Sridhar Samudrala L: linux-sctp@vger.kernel.org W: http://lksctp.sourceforge.net S: Supported @@ -5128,8 +4420,7 @@ F: include/net/sctp/ F: net/sctp/ SCx200 CPU SUPPORT -P: Jim Cromie -M: jim.cromie@gmail.com +M: Jim Cromie S: Odd Fixes F: Documentation/i2c/busses/scx200_acb F: arch/x86/kernel/scx200_32.c @@ -5139,49 +4430,42 @@ F: drivers/mtd/maps/scx200_docflash.c F: include/linux/scx200.h SCx200 GPIO DRIVER -P: Jim Cromie -M: jim.cromie@gmail.com +M: Jim Cromie S: Maintained F: drivers/char/scx200_gpio.c F: include/linux/scx200_gpio.h SCx200 HRT CLOCKSOURCE DRIVER -P: Jim Cromie -M: jim.cromie@gmail.com +M: Jim Cromie S: Maintained F: drivers/clocksource/scx200_hrt.c SDRICOH_CS MMC/SD HOST CONTROLLER INTERFACE DRIVER -P: Sascha Sommer -M: saschasommer@freenet.de +M: Sascha Sommer L: sdricohcs-devel@lists.sourceforge.net (subscribers-only) S: Maintained F: drivers/mmc/host/sdricoh_cs.c SECURE DIGITAL HOST CONTROLLER INTERFACE (SDHCI) DRIVER -P: Pierre Ossman -M: pierre@ossman.eu +M: Pierre Ossman L: sdhci-devel@lists.ossman.eu S: Maintained SECURE DIGITAL HOST CONTROLLER INTERFACE, OPEN FIRMWARE BINDINGS (SDHCI-OF) -P: Anton Vorontsov -M: avorontsov@ru.mvista.com +M: Anton Vorontsov L: linuxppc-dev@ozlabs.org L: sdhci-devel@lists.ossman.eu S: Maintained F: drivers/mmc/host/sdhci.* SECURE DIGITAL HOST CONTROLLER INTERFACE (SDHCI) SAMSUNG DRIVER -P: Ben Dooks -M: ben-linux@fluff.org +M: Ben Dooks L: sdhci-devel@lists.ossman.eu S: Maintained F: drivers/mmc/host/sdhci-s3c.c SECURITY SUBSYSTEM -P: James Morris -M: jmorris@namei.org +M: James Morris L: linux-security-module@vger.kernel.org (suggested Cc:) T: git git://www.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6.git W: http://security.wiki.kernel.org/ @@ -5189,17 +4473,13 @@ S: Supported F: security/ SECURITY CONTACT -P: Security Officers -M: security@kernel.org +M: Security Officers S: Supported SELINUX SECURITY MODULE -P: Stephen Smalley -M: sds@tycho.nsa.gov -P: James Morris -M: jmorris@namei.org -P: Eric Paris -M: eparis@parisplace.org +M: Stephen Smalley +M: James Morris +M: Eric Paris L: selinux@tycho.nsa.gov (subscribers-only, general discussion) W: http://selinuxproject.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6.git @@ -5208,15 +4488,13 @@ F: include/linux/selinux* F: security/selinux/ SENSABLE PHANTOM -P: Jiri Slaby -M: jirislaby@gmail.com +M: Jiri Slaby S: Maintained F: drivers/misc/phantom.c F: include/linux/phantom.h SERIAL ATA (SATA) SUBSYSTEM -P: Jeff Garzik -M: jgarzik@pobox.com +M: Jeff Garzik L: linux-ide@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev.git S: Supported @@ -5225,10 +4503,8 @@ F: include/linux/ata.h F: include/linux/libata.h SERVER ENGINES 10Gbps NIC - BladeEngine 2 DRIVER -P: Sathya Perla -M: sathyap@serverengines.com -P: Subbu Seetharaman -M: subbus@serverengines.com +M: Sathya Perla +M: Subbu Seetharaman L: netdev@vger.kernel.org W: http://www.serverengines.com S: Supported @@ -5237,20 +4513,17 @@ F: drivers/net/benet/ SFC NETWORK DRIVER P: Steve Hodgson P: Ben Hutchings -P: Robert Stonehouse -M: linux-net-drivers@solarflare.com +M: Robert Stonehouse S: Supported F: drivers/net/sfc/ SGI GRU DRIVER -P: Jack Steiner -M: steiner@sgi.com +M: Jack Steiner S: Maintained F: drivers/misc/sgi-gru/ SGI SN-IA64 (Altix) SERIAL CONSOLE DRIVER -P: Pat Gefre -M: pfg@sgi.com +M: Pat Gefre L: linux-ia64@vger.kernel.org S: Supported F: Documentation/ia64/serial.txt @@ -5258,22 +4531,19 @@ F: drivers/serial/ioc?_serial.c F: include/linux/ioc?.h SGI VISUAL WORKSTATION 320 AND 540 -P: Andrey Panin -M: pazke@donpac.ru +M: Andrey Panin L: linux-visws-devel@lists.sf.net W: http://linux-visws.sf.net S: Maintained for 2.6. F: Documentation/sgi-visws.txt SGI XP/XPC/XPNET DRIVER -P: Robin Holt -M: holt@sgi.com +M: Robin Holt S: Maintained F: drivers/misc/sgi-xp/ SHARP LH SUPPORT (LH7952X & LH7A40X) -P: Marc Singer -M: elf@buici.com +M: Marc Singer W: http://projects.buici.com/arm L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) S: Maintained @@ -5284,23 +4554,20 @@ F: drivers/usb/gadget/lh7a40* F: drivers/usb/host/ohci-lh7a40* SHPC HOTPLUG DRIVER -P: Kristen Carlson Accardi -M: kristen.c.accardi@intel.com +M: Kristen Carlson Accardi L: linux-pci@vger.kernel.org S: Supported F: drivers/pci/hotplug/shpchp* SIMTEC EB110ATX (Chalice CATS) P: Ben Dooks -P: Vincent Sanders -M: support@simtec.co.uk +M: Vincent Sanders W: http://www.simtec.co.uk/products/EB110ATX/ S: Supported SIMTEC EB2410ITX (BAST) P: Ben Dooks -P: Vincent Sanders -M: support@simtec.co.uk +M: Vincent Sanders W: http://www.simtec.co.uk/products/EB2410ITX/ S: Supported F: arch/arm/mach-s3c2410/ @@ -5308,31 +4575,27 @@ F: drivers/*/*s3c2410* F: drivers/*/*/*s3c2410* SIS 190 ETHERNET DRIVER -P: Francois Romieu -M: romieu@fr.zoreil.com +M: Francois Romieu L: netdev@vger.kernel.org S: Maintained F: drivers/net/sis190.c SIS 900/7016 FAST ETHERNET DRIVER -P: Daniele Venzano -M: venza@brownhat.org +M: Daniele Venzano W: http://www.brownhat.org/sis900.html L: netdev@vger.kernel.org S: Maintained F: drivers/net/sis900.* SIS 96X I2C/SMBUS DRIVER -P: Mark M. Hoffman -M: mhoffman@lightlink.com +M: "Mark M. Hoffman" L: linux-i2c@vger.kernel.org S: Maintained F: Documentation/i2c/busses/i2c-sis96x F: drivers/i2c/busses/i2c-sis96x.c SIS FRAMEBUFFER DRIVER -P: Thomas Winischhofer -M: thomas@winischhofer.net +M: Thomas Winischhofer W: http://www.winischhofer.net/linuxsisvga.shtml S: Maintained F: Documentation/fb/sisfb.txt @@ -5340,70 +4603,59 @@ F: drivers/video/sis/ F: include/video/sisfb.h SIS USB2VGA DRIVER -P: Thomas Winischhofer -M: thomas@winischhofer.net +M: Thomas Winischhofer W: http://www.winischhofer.at/linuxsisusbvga.shtml S: Maintained F: drivers/usb/misc/sisusbvga/ SKGE, SKY2 10/100/1000 GIGABIT ETHERNET DRIVERS -P: Stephen Hemminger -M: shemminger@linux-foundation.org +M: Stephen Hemminger L: netdev@vger.kernel.org S: Maintained F: drivers/net/skge.* F: drivers/net/sky2.* SLAB ALLOCATOR -P: Christoph Lameter -M: cl@linux-foundation.org -P: Pekka Enberg -M: penberg@cs.helsinki.fi -P: Matt Mackall -M: mpm@selenic.com +M: Christoph Lameter +M: Pekka Enberg +M: Matt Mackall L: linux-mm@kvack.org S: Maintained F: include/linux/sl?b*.h F: mm/sl?b.c SMC91x ETHERNET DRIVER -P: Nicolas Pitre -M: nico@cam.org +M: Nicolas Pitre S: Maintained F: drivers/net/smc91x.* SMSC47B397 HARDWARE MONITOR DRIVER -P: Mark M. Hoffman -M: mhoffman@lightlink.com +M: "Mark M. Hoffman" L: lm-sensors@lm-sensors.org S: Maintained F: Documentation/hwmon/smsc47b397 F: drivers/hwmon/smsc47b397.c SMSC911x ETHERNET DRIVER -P: Steve Glendinning -M: steve.glendinning@smsc.com +M: Steve Glendinning L: netdev@vger.kernel.org S: Supported F: include/linux/smsc911x.h F: drivers/net/smsc911x.* SMSC9420 PCI ETHERNET DRIVER -P: Steve Glendinning -M: steve.glendinning@smsc.com +M: Steve Glendinning L: netdev@vger.kernel.org S: Supported F: drivers/net/smsc9420.* SMX UIO Interface -P: Ben Nizette -M: bn@niasdigital.com +M: Ben Nizette S: Maintained F: drivers/uio/uio_smx.c SN-IA64 (Itanium) SUB-PLATFORM -P: Jes Sorensen -M: jes@sgi.com +M: Jes Sorensen L: linux-altix@sgi.com L: linux-ia64@vger.kernel.org W: http://www.sgi.com/altix @@ -5411,8 +4663,7 @@ S: Maintained F: arch/ia64/sn/ SOC-CAMERA V4L2 SUBSYSTEM -P: Guennadi Liakhovetski -M: g.liakhovetski@gmx.de +M: Guennadi Liakhovetski L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git S: Maintained @@ -5420,37 +4671,32 @@ F: include/media/v4l2* F: drivers/media/video/v4l2* SOEKRIS NET48XX LED SUPPORT -P: Chris Boot -M: bootc@bootc.net +M: Chris Boot S: Maintained F: drivers/leds/leds-net48xx.c SOFTWARE RAID (Multiple Disks) SUPPORT -P: Neil Brown -M: neilb@suse.de +M: Neil Brown L: linux-raid@vger.kernel.org S: Supported F: drivers/md/ F: include/linux/raid/ SONIC NETWORK DRIVER -P: Thomas Bogendoerfer -M: tsbogend@alpha.franken.de +M: Thomas Bogendoerfer L: netdev@vger.kernel.org S: Maintained F: drivers/net/sonic.* SONICS SILICON BACKPLANE DRIVER (SSB) -P: Michael Buesch -M: mb@bu3sch.de +M: Michael Buesch L: netdev@vger.kernel.org S: Maintained F: drivers/ssb/ F: include/linux/ssb/ SONY VAIO CONTROL DEVICE DRIVER -P: Mattia Dongili -M: malattia@linux.it +M: Mattia Dongili L: linux-acpi@vger.kernel.org W: http://www.linux.it/~malattia/wiki/index.php/Sony_drivers S: Maintained @@ -5460,17 +4706,14 @@ F: drivers/platform/x86/sony-laptop.c F: include/linux/sony-laptop.h SONY MEMORYSTICK CARD SUPPORT -P: Alex Dubov -M: oakad@yahoo.com +M: Alex Dubov W: http://tifmxx.berlios.de/ S: Maintained F: drivers/memstick/host/tifm_ms.c SOUND -P: Jaroslav Kysela -M: perex@perex.cz -P: Takashi Iwai -M: tiwai@suse.de +M: Jaroslav Kysela +M: Takashi Iwai L: alsa-devel@alsa-project.org (moderated for non-subscribers) W: http://www.alsa-project.org/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6.git @@ -5481,10 +4724,8 @@ F: include/sound/ F: sound/ SOUND - SOC LAYER / DYNAMIC AUDIO POWER MANAGEMENT (ASoC) -P: Liam Girdwood -M: lrg@slimlogic.co.uk -P: Mark Brown -M: broonie@opensource.wolfsonmicro.com +M: Liam Girdwood +M: Mark Brown T: git git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6.git L: alsa-devel@alsa-project.org (moderated for non-subscribers) W: http://alsa-project.org/main/index.php/ASoC @@ -5493,8 +4734,7 @@ F: sound/soc/ F: include/sound/soc* SPARC + UltraSPARC (sparc/sparc64) -P: David S. Miller -M: davem@davemloft.net +M: "David S. Miller" L: sparclinux@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6.git T: git git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6.git @@ -5502,15 +4742,13 @@ S: Maintained F: arch/sparc/ SPECIALIX IO8+ MULTIPORT SERIAL CARD DRIVER -P: Roger Wolff -M: R.E.Wolff@BitWizard.nl +M: Roger Wolff S: Supported F: Documentation/serial/specialix.txt F: drivers/char/specialix* SPI SUBSYSTEM -P: David Brownell -M: dbrownell@users.sourceforge.net +M: David Brownell L: spi-devel-general@lists.sourceforge.net S: Maintained F: Documentation/spi/ @@ -5518,18 +4756,15 @@ F: drivers/spi/ F: include/linux/spi/ SPIDERNET NETWORK DRIVER for CELL -P: Ishizaki Kou -M: kou.ishizaki@toshiba.co.jp -P: Jens Osterkamp -M: jens@de.ibm.com +M: Ishizaki Kou +M: Jens Osterkamp L: netdev@vger.kernel.org S: Supported F: Documentation/networking/spider_net.txt F: drivers/net/spider_net* SPU FILE SYSTEM -P: Jeremy Kerr -M: jk@ozlabs.org +M: Jeremy Kerr L: linuxppc-dev@ozlabs.org L: cbe-oss-dev@ozlabs.org W: http://www.ibm.com/developerworks/power/cell/ @@ -5538,8 +4773,7 @@ F: Documentation/filesystems/spufs.txt F: arch/powerpc/platforms/cell/spufs/ SQUASHFS FILE SYSTEM -P: Phillip Lougher -M: phillip@lougher.demon.co.uk +M: Phillip Lougher L: squashfs-devel@lists.sourceforge.net (subscribers-only) W: http://squashfs.org.uk S: Maintained @@ -5547,30 +4781,25 @@ F: Documentation/filesystems/squashfs.txt F: fs/squashfs/ SRM (Alpha) environment access -P: Jan-Benedict Glaw -M: jbglaw@lug-owl.de +M: Jan-Benedict Glaw S: Maintained F: arch/alpha/kernel/srm_env.c STABLE BRANCH -P: Greg Kroah-Hartman -M: greg@kroah.com -P: Chris Wright -M: chrisw@sous-sol.org +M: Greg Kroah-Hartman +M: Chris Wright L: stable@kernel.org S: Maintained STAGING SUBSYSTEM -P: Greg Kroah-Hartman -M: gregkh@suse.de +M: Greg Kroah-Hartman T: quilt kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/ L: devel@driverdev.osuosl.org S: Maintained F: drivers/staging/ STARFIRE/DURALAN NETWORK DRIVER -P: Ion Badulescu -M: ionut@badula.org +M: Ion Badulescu S: Odd Fixes F: drivers/net/starfire* @@ -5580,15 +4809,13 @@ F: drivers/net/wireless/strip.c F: include/linux/if_strip.h STRADIS MPEG-2 DECODER DRIVER -P: Nathan Laredo -M: laredo@gnu.org +M: Nathan Laredo W: http://www.stradis.com/ S: Maintained F: drivers/media/video/stradis.c SUN3/3X -P: Sam Creasey -M: sammy@sammy.net +M: Sam Creasey W: http://sammy.net/sun3/ S: Maintained F: arch/m68k/kernel/*sun3* @@ -5596,8 +4823,7 @@ F: arch/m68k/sun3*/ F: arch/m68k/include/asm/sun3* SUPERH -P: Paul Mundt -M: lethal@linux-sh.org +M: Paul Mundt L: linux-sh@vger.kernel.org W: http://www.linux-sh.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.git @@ -5607,12 +4833,9 @@ F: arch/sh/ F: drivers/sh/ SUSPEND TO RAM -P: Len Brown -M: len.brown@intel.com -P: Pavel Machek -M: pavel@ucw.cz -P: Rafael J. Wysocki -M: rjw@sisk.pl +M: Len Brown +M: Pavel Machek +M: "Rafael J. Wysocki" L: linux-pm@lists.linux-foundation.org S: Supported F: Documentation/power/ @@ -5624,32 +4847,28 @@ F: include/linux/freezer.h F: include/linux/pm.h SVGA HANDLING -P: Martin Mares -M: mj@ucw.cz +M: Martin Mares L: linux-video@atrey.karlin.mff.cuni.cz S: Maintained F: Documentation/svga.txt F: arch/x86/boot/video* SYSV FILESYSTEM -P: Christoph Hellwig -M: hch@infradead.org +M: Christoph Hellwig S: Maintained F: Documentation/filesystems/sysv-fs.txt F: fs/sysv/ F: include/linux/sysv_fs.h TASKSTATS STATISTICS INTERFACE -P: Balbir Singh -M: balbir@linux.vnet.ibm.com +M: Balbir Singh S: Maintained F: Documentation/accounting/taskstats* F: include/linux/taskstats* F: kernel/taskstats.c TC CLASSIFIER -P: Jamal Hadi Salim -M: hadi@cyberus.ca +M: Jamal Hadi Salim L: netdev@vger.kernel.org S: Maintained F: include/linux/pkt_cls.h @@ -5657,38 +4876,31 @@ F: include/net/pkt_cls.h F: net/sched/ TCP LOW PRIORITY MODULE -P: Wong Hoi Sing, Edison -M: hswong3i@gmail.com -P: Hung Hing Lun, Mike -M: hlhung3i@gmail.com +M: "Wong Hoi Sing, Edison" +M: "Hung Hing Lun, Mike" W: http://tcp-lp-mod.sourceforge.net/ S: Maintained F: net/ipv4/tcp_lp.c TEHUTI ETHERNET DRIVER -P: Alexander Indenbaum -M: baum@tehutinetworks.net -P: Andy Gospodarek -M: andy@greyhouse.net +M: Alexander Indenbaum +M: Andy Gospodarek L: netdev@vger.kernel.org S: Supported F: drivers/net/tehuti* Telecom Clock Driver for MCPL0010 -P: Mark Gross -M: mark.gross@intel.com +M: Mark Gross S: Supported F: drivers/char/tlclk.c TENSILICA XTENSA PORT (xtensa) -P: Chris Zankel -M: chris@zankel.net +M: Chris Zankel S: Maintained F: arch/xtensa/ THINKPAD ACPI EXTRAS DRIVER -P: Henrique de Moraes Holschuh -M: ibm-acpi@hmh.eng.br +M: Henrique de Moraes Holschuh L: ibm-acpi-devel@lists.sourceforge.net W: http://ibm-acpi.sourceforge.net W: http://thinkwiki.org/wiki/Ibm-acpi @@ -5697,27 +4909,22 @@ S: Maintained F: drivers/platform/x86/thinkpad_acpi.c TI FLASH MEDIA INTERFACE DRIVER -P: Alex Dubov -M: oakad@yahoo.com +M: Alex Dubov S: Maintained F: drivers/misc/tifm* F: drivers/mmc/host/tifm_sd.c F: include/linux/tifm.h TI TWL4030 SERIES SOC CODEC DRIVER -P: Peter Ujfalusi -M: peter.ujfalusi@nokia.com +M: Peter Ujfalusi L: alsa-devel@alsa-project.org (moderated for non-subscribers) S: Maintained F: sound/soc/codecs/twl4030* TIPC NETWORK LAYER -P: Per Liden -M: per.liden@ericsson.com -P: Jon Maloy -M: jon.maloy@ericsson.com -P: Allan Stephens -M: allan.stephens@windriver.com +M: Per Liden +M: Jon Maloy +M: Allan Stephens L: tipc-discussion@lists.sourceforge.net W: http://tipc.sourceforge.net/ W: http://tipc.cslab.ericsson.net/ @@ -5728,8 +4935,7 @@ F: include/net/tipc/ F: net/tipc/ TLAN NETWORK DRIVER -P: Samuel Chessman -M: chessman@tux.org +M: Samuel Chessman L: tlan-devel@lists.sourceforge.net (subscribers-only) W: http://sourceforge.net/projects/tlan/ S: Maintained @@ -5737,10 +4943,8 @@ F: Documentation/networking/tlan.txt F: drivers/net/tlan.* TOMOYO SECURITY MODULE -P: Kentaro Takeda -M: takedakn@nttdata.co.jp -P: Tetsuo Handa -M: penguin-kernel@I-love.SAKURA.ne.jp +M: Kentaro Takeda +M: Tetsuo Handa L: tomoyo-users-en@lists.sourceforge.jp (subscribers-only, for developers and users in English) L: tomoyo-dev@lists.sourceforge.jp (subscribers-only, for developers in Japanese) L: tomoyo-users@lists.sourceforge.jp (subscribers-only, for users in Japanese) @@ -5754,8 +4958,7 @@ S: Orphan F: drivers/platform/x86/toshiba_acpi.c TOSHIBA SMM DRIVER -P: Jonathan Buzzard -M: jonathan@buzzard.org.uk +M: Jonathan Buzzard L: tlinux-users@tce.toshiba-dme.co.jp W: http://www.buzzard.org.uk/toshiba/ S: Maintained @@ -5763,41 +4966,34 @@ F: drivers/char/toshiba.c F: include/linux/toshiba.h TMIO MMC DRIVER -P: Ian Molton -M: ian@mnementh.co.uk +M: Ian Molton S: Maintained F: drivers/mmc/host/tmio_mmc.* TMPFS (SHMEM FILESYSTEM) -P: Hugh Dickins -M: hugh.dickins@tiscali.co.uk +M: Hugh Dickins L: linux-mm@kvack.org S: Maintained F: include/linux/shmem_fs.h F: mm/shmem.c TPM DEVICE DRIVER -P: Debora Velarde -M: debora@linux.vnet.ibm.com -P: Rajiv Andrade -M: srajiv@linux.vnet.ibm.com +M: Debora Velarde +M: Rajiv Andrade W: http://tpmdd.sourceforge.net -P: Marcel Selhorst -M: m.selhorst@sirrix.com +M: Marcel Selhorst W: http://www.sirrix.com L: tpmdd-devel@lists.sourceforge.net (moderated for non-subscribers) S: Maintained F: drivers/char/tpm/ TRIVIAL PATCHES -P: Jiri Kosina -M: trivial@kernel.org +M: Jiri Kosina T: git git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial.git S: Maintained TTY LAYER -P: Alan Cox -M: alan@lxorguk.ukuu.org.uk +M: Alan Cox S: Maintained T: stgit http://zeniv.linux.org.uk/~alan/ttydev/ F: drivers/char/tty_* @@ -5807,17 +5003,14 @@ F: include/linux/serial.h F: include/linux/tty.h TULIP NETWORK DRIVERS -P: Grant Grundler -M: grundler@parisc-linux.org -P: Kyle McMartin -M: kyle@mcmartin.ca +M: Grant Grundler +M: Kyle McMartin L: netdev@vger.kernel.org S: Maintained F: drivers/net/tulip/ TUN/TAP driver -P: Maxim Krasnyansky -M: maxk@qualcomm.com +M: Maxim Krasnyansky L: vtun@office.satix.net W: http://vtun.sourceforge.net/tun S: Maintained @@ -5825,24 +5018,20 @@ F: Documentation/networking/tuntap.txt F: arch/um/os-Linux/drivers/ TURBOCHANNEL SUBSYSTEM -P: Maciej W. Rozycki -M: macro@linux-mips.org +M: "Maciej W. Rozycki" S: Maintained F: drivers/tc/ F: include/linux/tc.h U14-34F SCSI DRIVER -P: Dario Ballabio -M: ballabio_dario@emc.com +M: Dario Ballabio L: linux-scsi@vger.kernel.org S: Maintained F: drivers/scsi/u14-34f.c UBI FILE SYSTEM (UBIFS) -P: Artem Bityutskiy -M: dedekind@infradead.org -P: Adrian Hunter -M: adrian.hunter@nokia.com +M: Artem Bityutskiy +M: Adrian Hunter L: linux-mtd@lists.infradead.org T: git git://git.infradead.org/ubifs-2.6.git W: http://www.linux-mtd.infradead.org/doc/ubifs.html @@ -5851,37 +5040,32 @@ F: Documentation/filesystems/ubifs.txt F: fs/ubifs/ UCLINUX (AND M68KNOMMU) -P: Greg Ungerer -M: gerg@uclinux.org +M: Greg Ungerer W: http://www.uclinux.org/ L: uclinux-dev@uclinux.org (subscribers-only) S: Maintained F: arch/m68knommu/ UCLINUX FOR RENESAS H8/300 (H8300) -P: Yoshinori Sato -M: ysato@users.sourceforge.jp +M: Yoshinori Sato W: http://uclinux-h8.sourceforge.jp/ S: Supported UDF FILESYSTEM -P: Jan Kara -M: jack@suse.cz +M: Jan Kara W: http://linux-udf.sourceforge.net S: Maintained F: Documentation/filesystems/udf.txt F: fs/udf/ UFS FILESYSTEM -P: Evgeniy Dushistov -M: dushistov@mail.ru +M: Evgeniy Dushistov S: Maintained F: Documentation/filesystems/ufs.txt F: fs/ufs/ ULTRA-WIDEBAND (UWB) SUBSYSTEM: -P: David Vrabel -M: david.vrabel@csr.com +M: David Vrabel L: linux-usb@vger.kernel.org S: Supported F: drivers/uwb/* @@ -5889,8 +5073,7 @@ F: include/linux/uwb.h F: include/linux/uwb/ UNIFORM CDROM DRIVER -P: Jens Axboe -M: axboe@kernel.dk +M: Jens Axboe W: http://www.kernel.dk S: Maintained F: Documentation/cdrom/ @@ -5898,8 +5081,7 @@ F: drivers/cdrom/cdrom.c F: include/linux/cdrom.h UNSORTED BLOCK IMAGES (UBI) -P: Artem Bityutskiy -M: dedekind@infradead.org +M: Artem Bityutskiy W: http://www.linux-mtd.infradead.org/ L: linux-mtd@lists.infradead.org T: git git://git.infradead.org/ubi-2.6.git @@ -5909,23 +5091,20 @@ F: include/linux/mtd/ubi.h F: include/mtd/ubi-user.h USB ACM DRIVER -P: Oliver Neukum -M: oliver@neukum.name +M: Oliver Neukum L: linux-usb@vger.kernel.org S: Maintained F: Documentation/usb/acm.txt F: drivers/usb/class/cdc-acm.* USB BLOCK DRIVER (UB ub) -P: Pete Zaitcev -M: zaitcev@redhat.com +M: Pete Zaitcev L: linux-usb@vger.kernel.org S: Supported F: drivers/block/ub.c USB CDC ETHERNET DRIVER -P: Greg Kroah-Hartman -M: greg@kroah.com +M: Greg Kroah-Hartman L: linux-usb@vger.kernel.org S: Maintained W: http://www.kroah.com/linux-usb/ @@ -5933,39 +5112,34 @@ F: drivers/net/usb/cdc_*.c F: include/linux/usb/cdc.h USB CYPRESS C67X00 DRIVER -P: Peter Korsgaard -M: jacmet@sunsite.dk +M: Peter Korsgaard L: linux-usb@vger.kernel.org S: Maintained F: drivers/usb/c67x00/ USB DAVICOM DM9601 DRIVER -P: Peter Korsgaard -M: jacmet@sunsite.dk +M: Peter Korsgaard L: netdev@vger.kernel.org W: http://www.linux-usb.org/usbnet S: Maintained F: drivers/net/usb/dm9601.c USB DIAMOND RIO500 DRIVER -P: Cesar Miquel -M: miquel@df.uba.ar +M: Cesar Miquel L: rio500-users@lists.sourceforge.net W: http://rio500.sourceforge.net S: Maintained F: drivers/usb/misc/rio500* USB EHCI DRIVER -P: David Brownell -M: dbrownell@users.sourceforge.net +M: David Brownell L: linux-usb@vger.kernel.org S: Odd Fixes F: Documentation/usb/ehci.txt F: drivers/usb/host/ehci* USB ET61X[12]51 DRIVER -P: Luca Risolia -M: luca.risolia@studio.unibo.it +M: Luca Risolia L: linux-usb@vger.kernel.org L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git @@ -5974,8 +5148,7 @@ S: Maintained F: drivers/media/video/et61x251/ USB GADGET/PERIPHERAL SUBSYSTEM -P: David Brownell -M: dbrownell@users.sourceforge.net +M: David Brownell L: linux-usb@vger.kernel.org W: http://www.linux-usb.org/gadget S: Maintained @@ -5983,8 +5156,7 @@ F: drivers/usb/gadget/ F: include/linux/usb/gadget* USB HID/HIDBP DRIVERS (USB KEYBOARDS, MICE, REMOTE CONTROLS, ...) -P: Jiri Kosina -M: jkosina@suse.cz +M: Jiri Kosina L: linux-usb@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid.git S: Maintained @@ -5992,23 +5164,20 @@ F: Documentation/usb/hiddev.txt F: drivers/hid/usbhid/ USB ISP116X DRIVER -P: Olav Kongas -M: ok@artecdesign.ee +M: Olav Kongas L: linux-usb@vger.kernel.org S: Maintained F: drivers/usb/host/isp116x* F: include/linux/usb/isp116x.h USB KAWASAKI LSI DRIVER -P: Oliver Neukum -M: oliver@neukum.name +M: Oliver Neukum L: linux-usb@vger.kernel.org S: Maintained F: drivers/usb/serial/kl5kusb105.* USB MASS STORAGE DRIVER -P: Matthew Dharm -M: mdharm-usb@one-eyed-alien.net +M: Matthew Dharm L: linux-usb@vger.kernel.org L: usb-storage@lists.one-eyed-alien.net S: Maintained @@ -6016,31 +5185,27 @@ W: http://www.one-eyed-alien.net/~mdharm/linux-usb/ F: drivers/usb/storage/ USB OHCI DRIVER -P: David Brownell -M: dbrownell@users.sourceforge.net +M: David Brownell L: linux-usb@vger.kernel.org S: Odd Fixes F: Documentation/usb/ohci.txt F: drivers/usb/host/ohci* USB OPTION-CARD DRIVER -P: Matthias Urlichs -M: smurf@smurf.noris.de +M: Matthias Urlichs L: linux-usb@vger.kernel.org S: Maintained F: drivers/usb/serial/option.c USB OV511 DRIVER -P: Mark McClelland -M: mmcclell@bigfoot.com +M: Mark McClelland L: linux-usb@vger.kernel.org W: http://alpha.dyndns.org/ov511/ S: Maintained F: drivers/media/video/ov511.* USB PEGASUS DRIVER -P: Petko Manolov -M: petkan@users.sourceforge.net +M: Petko Manolov L: linux-usb@vger.kernel.org L: netdev@vger.kernel.org W: http://pegasus2.sourceforge.net/ @@ -6048,15 +5213,13 @@ S: Maintained F: drivers/net/usb/pegasus.* USB PRINTER DRIVER (usblp) -P: Pete Zaitcev -M: zaitcev@redhat.com +M: Pete Zaitcev L: linux-usb@vger.kernel.org S: Supported F: drivers/usb/class/usblp.c USB RTL8150 DRIVER -P: Petko Manolov -M: petkan@users.sourceforge.net +M: Petko Manolov L: linux-usb@vger.kernel.org L: netdev@vger.kernel.org W: http://pegasus2.sourceforge.net/ @@ -6064,8 +5227,7 @@ S: Maintained F: drivers/net/usb/rtl8150.c USB SE401 DRIVER -P: Jeroen Vreeken -M: pe1rxq@amsat.org +M: Jeroen Vreeken L: linux-usb@vger.kernel.org W: http://www.chello.nl/~j.vreeken/se401/ S: Maintained @@ -6073,15 +5235,13 @@ F: Documentation/video4linux/se401.txt F: drivers/media/video/se401.* USB SERIAL BELKIN F5U103 DRIVER -P: William Greathouse -M: wgreathouse@smva.com +M: William Greathouse L: linux-usb@vger.kernel.org S: Maintained F: drivers/usb/serial/belkin_sa.* USB SERIAL CYPRESS M8 DRIVER -P: Lonnie Mendez -M: dignome@gmail.com +M: Lonnie Mendez L: linux-usb@vger.kernel.org S: Maintained W: http://geocities.com/i0xox0i @@ -6089,24 +5249,20 @@ W: http://firstlight.net/cvs F: drivers/usb/serial/cypress_m8.* USB SERIAL CYBERJACK DRIVER -P: Matthias Bruestle and Harald Welte -M: support@reiner-sct.com +M: Matthias Bruestle and Harald Welte W: http://www.reiner-sct.de/support/treiber_cyberjack.php S: Maintained F: drivers/usb/serial/cyberjack.c USB SERIAL DIGI ACCELEPORT DRIVER -P: Peter Berger -M: pberger@brimson.com -P: Al Borchers -M: alborchers@steinerpoint.com +M: Peter Berger +M: Al Borchers L: linux-usb@vger.kernel.org S: Maintained F: drivers/usb/serial/digi_acceleport.c USB SERIAL DRIVER -P: Greg Kroah-Hartman -M: gregkh@suse.de +M: Greg Kroah-Hartman L: linux-usb@vger.kernel.org S: Supported F: Documentation/usb/usb-serial.txt @@ -6115,38 +5271,33 @@ F: drivers/usb/serial/usb-serial.c F: include/linux/usb/serial.h USB SERIAL EMPEG EMPEG-CAR MARK I/II DRIVER -P: Gary Brubaker -M: xavyer@ix.netcom.com +M: Gary Brubaker L: linux-usb@vger.kernel.org S: Maintained F: drivers/usb/serial/empeg.c USB SERIAL KEYSPAN DRIVER -P: Greg Kroah-Hartman -M: greg@kroah.com +M: Greg Kroah-Hartman L: linux-usb@vger.kernel.org W: http://www.kroah.com/linux/ S: Maintained F: drivers/usb/serial/*keyspan* USB SERIAL WHITEHEAT DRIVER -P: Support Department -M: support@connecttech.com +M: Support Department L: linux-usb@vger.kernel.org W: http://www.connecttech.com S: Supported F: drivers/usb/serial/whiteheat* USB SMSC95XX ETHERNET DRIVER -P: Steve Glendinning -M: steve.glendinning@smsc.com +M: Steve Glendinning L: netdev@vger.kernel.org S: Supported F: drivers/net/usb/smsc95xx.* USB SN9C1xx DRIVER -P: Luca Risolia -M: luca.risolia@studio.unibo.it +M: Luca Risolia L: linux-usb@vger.kernel.org L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git @@ -6156,8 +5307,7 @@ F: Documentation/video4linux/sn9c102.txt F: drivers/media/video/sn9c102/ USB SUBSYSTEM -P: Greg Kroah-Hartman -M: gregkh@suse.de +M: Greg Kroah-Hartman L: linux-usb@vger.kernel.org W: http://www.linux-usb.org T: quilt kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/ @@ -6169,15 +5319,13 @@ F: include/linux/usb.h F: include/linux/usb/ USB UHCI DRIVER -P: Alan Stern -M: stern@rowland.harvard.edu +M: Alan Stern L: linux-usb@vger.kernel.org S: Maintained F: drivers/usb/host/uhci* USB "USBNET" DRIVER FRAMEWORK -P: David Brownell -M: dbrownell@users.sourceforge.net +M: David Brownell L: netdev@vger.kernel.org W: http://www.linux-usb.org/usbnet S: Maintained @@ -6185,8 +5333,7 @@ F: drivers/net/usb/usbnet.c F: include/linux/usb/usbnet.h USB VIDEO CLASS -P: Laurent Pinchart -M: laurent.pinchart@skynet.be +M: Laurent Pinchart L: linux-uvc-devel@lists.berlios.de (subscribers-only) L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git @@ -6195,8 +5342,7 @@ S: Maintained F: drivers/media/video/uvc/ USB W996[87]CF DRIVER -P: Luca Risolia -M: luca.risolia@studio.unibo.it +M: Luca Risolia L: linux-usb@vger.kernel.org L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git @@ -6206,21 +5352,18 @@ F: Documentation/video4linux/w9968cf.txt F: drivers/media/video/w996* USB WIRELESS RNDIS DRIVER (rndis_wlan) -P: Jussi Kivilinna -M: jussi.kivilinna@mbnet.fi +M: Jussi Kivilinna L: linux-wireless@vger.kernel.org S: Maintained F: drivers/net/wireless/rndis_wlan.c USB XHCI DRIVER -P: Sarah Sharp -M: sarah.a.sharp@intel.com +M: Sarah Sharp L: linux-usb@vger.kernel.org S: Supported USB ZC0301 DRIVER -P: Luca Risolia -M: luca.risolia@studio.unibo.it +M: Luca Risolia L: linux-usb@vger.kernel.org L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git @@ -6230,16 +5373,14 @@ F: Documentation/video4linux/zc0301.txt F: drivers/media/video/zc0301/ USB ZD1201 DRIVER -P: Jeroen Vreeken -M: pe1rxq@amsat.org +M: Jeroen Vreeken L: linux-usb@vger.kernel.org W: http://linux-lc100020.sourceforge.net S: Maintained F: drivers/net/wireless/zd1201.* USB ZR364XX DRIVER -P: Antoine Jacquet -M: royale@zerezo.com +M: Antoine Jacquet L: linux-usb@vger.kernel.org L: linux-media@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git @@ -6249,8 +5390,7 @@ F: Documentation/video4linux/zr364xx.txt F: drivers/media/video/zr364xx.c USER-MODE LINUX (UML) -P: Jeff Dike -M: jdike@addtoit.com +M: Jeff Dike L: user-mode-linux-devel@lists.sourceforge.net L: user-mode-linux-user@lists.sourceforge.net W: http://user-mode-linux.sourceforge.net @@ -6261,26 +5401,22 @@ F: fs/hostfs/ F: fs/hppfs/ USERSPACE I/O (UIO) -P: Hans J. Koch -M: hjk@linutronix.de -P: Greg Kroah-Hartman -M: gregkh@suse.de +M: "Hans J. Koch" +M: Greg Kroah-Hartman S: Maintained F: Documentation/DocBook/uio-howto.tmpl F: drivers/uio/ F: include/linux/uio*.h UTIL-LINUX-NG PACKAGE -P: Karel Zak -M: kzak@redhat.com +M: Karel Zak L: util-linux-ng@vger.kernel.org W: http://kernel.org/~kzak/util-linux-ng/ T: git git://git.kernel.org/pub/scm/utils/util-linux-ng/util-linux-ng.git S: Maintained UVESAFB DRIVER -P: Michal Januszewski -M: spock@gentoo.org +M: Michal Januszewski L: linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers) W: http://dev.gentoo.org/~spock/projects/uvesafb/ S: Maintained @@ -6288,53 +5424,44 @@ F: Documentation/fb/uvesafb.txt F: drivers/video/uvesafb.* VFAT/FAT/MSDOS FILESYSTEM -P: OGAWA Hirofumi -M: hirofumi@mail.parknet.co.jp +M: OGAWA Hirofumi S: Maintained F: Documentation/filesystems/vfat.txt F: fs/fat/ VIA RHINE NETWORK DRIVER -P: Roger Luethi -M: rl@hellgate.ch +M: Roger Luethi S: Maintained F: drivers/net/via-rhine.c VIAPRO SMBUS DRIVER -P: Jean Delvare -M: khali@linux-fr.org +M: Jean Delvare L: linux-i2c@vger.kernel.org S: Maintained F: Documentation/i2c/busses/i2c-viapro F: drivers/i2c/busses/i2c-viapro.c VIA SD/MMC CARD CONTROLLER DRIVER -P: Joseph Chan -M: JosephChan@via.com.tw -P: Harald Welte -M: HaraldWelte@viatech.com +M: Joseph Chan +M: Harald Welte S: Maintained F: drivers/mmc/host/via-sdmmc.c VIA UNICHROME(PRO)/CHROME9 FRAMEBUFFER DRIVER -P: Joseph Chan -M: JosephChan@via.com.tw -P: Scott Fang -M: ScottFang@viatech.com.cn +M: Joseph Chan +M: Scott Fang L: linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers) S: Maintained F: drivers/video/via/ VIA VELOCITY NETWORK DRIVER -P: Francois Romieu -M: romieu@fr.zoreil.com +M: Francois Romieu L: netdev@vger.kernel.org S: Maintained F: drivers/net/via-velocity.* VLAN (802.1Q) -P: Patrick McHardy -M: kaber@trash.net +M: Patrick McHardy L: netdev@vger.kernel.org S: Maintained F: drivers/net/macvlan.c @@ -6342,18 +5469,15 @@ F: include/linux/if_*vlan.h F: net/8021q/ VLYNQ BUS -P: Florian Fainelli -M: florian@openwrt.org +M: Florian Fainelli L: openwrt-devel@lists.openwrt.org S: Maintained F: drivers/vlynq/vlynq.c F: include/linux/vlynq.h VOLTAGE AND CURRENT REGULATOR FRAMEWORK -P: Liam Girdwood -M: lrg@slimlogic.co.uk -P: Mark Brown -M: broonie@opensource.wolfsonmicro.com +M: Liam Girdwood +M: Mark Brown W: http://opensource.wolfsonmicro.com/node/15 W: http://www.slimlogic.co.uk/?p=48 T: git git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6.git @@ -6362,52 +5486,45 @@ F: drivers/regulator/ F: include/linux/regulator/ VT1211 HARDWARE MONITOR DRIVER -P: Juerg Haefliger -M: juergh@gmail.com +M: Juerg Haefliger L: lm-sensors@lm-sensors.org S: Maintained F: Documentation/hwmon/vt1211 F: drivers/hwmon/vt1211.c VT8231 HARDWARE MONITOR DRIVER -P: Roger Lucas -M: vt8231@hiddenengine.co.uk +M: Roger Lucas L: lm-sensors@lm-sensors.org S: Maintained F: drivers/hwmon/vt8231.c W1 DALLAS'S 1-WIRE BUS -P: Evgeniy Polyakov -M: johnpol@2ka.mipt.ru +M: Evgeniy Polyakov S: Maintained F: Documentation/w1/ F: drivers/w1/ W83791D HARDWARE MONITORING DRIVER -P: Marc Hulsman -M: m.hulsman@tudelft.nl +M: Marc Hulsman L: lm-sensors@lm-sensors.org S: Maintained F: Documentation/hwmon/w83791d F: drivers/hwmon/w83791d.c W83793 HARDWARE MONITORING DRIVER -P: Rudolf Marek -M: r.marek@assembler.cz +M: Rudolf Marek L: lm-sensors@lm-sensors.org S: Maintained F: Documentation/hwmon/w83793 F: drivers/hwmon/w83793.c W83L51xD SD/MMC CARD INTERFACE DRIVER -P: Pierre Ossman -M: pierre@ossman.eu +M: Pierre Ossman S: Maintained F: drivers/mmc/host/wbsd.* WATCHDOG DEVICE DRIVERS -P: Wim Van Sebroeck -M: wim@iguana.be +M: Wim Van Sebroeck T: git git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog.git S: Maintained F: Documentation/watchdog/ @@ -6415,8 +5532,7 @@ F: drivers/watchdog/ F: include/linux/watchdog.h WAVELAN NETWORK DRIVER & WIRELESS EXTENSIONS -P: Jean Tourrilhes -M: jt@hpl.hp.com +M: Jean Tourrilhes L: linux-wireless@vger.kernel.org W: http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/ S: Maintained @@ -6424,46 +5540,39 @@ F: Documentation/networking/wavelan.txt F: drivers/net/wireless/wavelan* WD7000 SCSI DRIVER -P: Miroslav Zagorac -M: zaga@fly.cc.fer.hr +M: Miroslav Zagorac L: linux-scsi@vger.kernel.org S: Maintained F: drivers/scsi/wd7000.c WIMAX STACK -P: Inaky Perez-Gonzalez -M: inaky.perez-gonzalez@intel.com +M: Inaky Perez-Gonzalez M: linux-wimax@intel.com L: wimax@linuxwimax.org S: Supported W: http://linuxwimax.org WIMEDIA LLC PROTOCOL (WLP) SUBSYSTEM -P: David Vrabel -M: david.vrabel@csr.com +M: David Vrabel S: Maintained F: include/linux/wlp.h F: drivers/uwb/wlp/ WISTRON LAPTOP BUTTON DRIVER -P: Miloslav Trmac -M: mitr@volny.cz +M: Miloslav Trmac S: Maintained F: drivers/input/misc/wistron_btns.c WL3501 WIRELESS PCMCIA CARD DRIVER -P: Arnaldo Carvalho de Melo -M: acme@ghostprotocols.net +M: Arnaldo Carvalho de Melo L: linux-wireless@vger.kernel.org W: http://oops.ghostprotocols.net:81/blog S: Maintained F: drivers/net/wireless/wl3501* WM97XX TOUCHSCREEN DRIVERS -P: Mark Brown -M: broonie@opensource.wolfsonmicro.com -P: Liam Girdwood -M: lrg@slimlogic.co.uk +M: Mark Brown +M: Liam Girdwood L: linux-input@vger.kernel.org T: git git://opensource.wolfsonmicro.com/linux-2.6-touch W: http://opensource.wolfsonmicro.com/node/7 @@ -6472,8 +5581,7 @@ F: drivers/input/touchscreen/*wm97* F: include/linux/wm97xx.h X.25 NETWORK LAYER -P: Henner Eisen -M: eis@baty.hanse.de +M: Henner Eisen L: linux-x25@vger.kernel.org S: Maintained F: Documentation/networking/x25* @@ -6481,12 +5589,9 @@ F: include/net/x25* F: net/x25/ X86 ARCHITECTURE (32-BIT AND 64-BIT) -P: Thomas Gleixner -M: tglx@linutronix.de -P: Ingo Molnar -M: mingo@redhat.com -P: H. Peter Anvin -M: hpa@zytor.com +M: Thomas Gleixner +M: Ingo Molnar +M: "H. Peter Anvin" M: x86@kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86.git S: Maintained @@ -6494,10 +5599,8 @@ F: Documentation/x86/ F: arch/x86/ XEN HYPERVISOR INTERFACE -P: Jeremy Fitzhardinge -M: jeremy@xensource.com -P: Chris Wright -M: chrisw@sous-sol.org +M: Jeremy Fitzhardinge +M: Chris Wright L: virtualization@lists.osdl.org L: xen-devel@lists.xensource.com S: Supported @@ -6509,8 +5612,7 @@ F: include/xen/ XFS FILESYSTEM P: Silicon Graphics Inc -P: Felix Blyakher -M: felixb@sgi.com +M: Felix Blyakher M: xfs-masters@oss.sgi.com L: xfs@oss.sgi.com W: http://oss.sgi.com/projects/xfs @@ -6520,38 +5622,33 @@ F: Documentation/filesystems/xfs.txt F: fs/xfs/ XILINX SYSTEMACE DRIVER -P: Grant Likely -M: grant.likely@secretlab.ca +M: Grant Likely W: http://www.secretlab.ca/ S: Maintained F: drivers/block/xsysace.c XILINX UARTLITE SERIAL DRIVER -P: Peter Korsgaard -M: jacmet@sunsite.dk +M: Peter Korsgaard L: linux-serial@vger.kernel.org S: Maintained F: drivers/serial/uartlite.c YAM DRIVER FOR AX.25 -P: Jean-Paul Roubelat -M: jpr@f6fbb.org +M: Jean-Paul Roubelat L: linux-hams@vger.kernel.org S: Maintained F: drivers/net/hamradio/yam* F: include/linux/yam.h YEALINK PHONE DRIVER -P: Henk Vergonet -M: Henk.Vergonet@gmail.com +M: Henk Vergonet L: usbb2k-api-dev@nongnu.org S: Maintained F: Documentation/input/yealink.txt F: drivers/input/misc/yealink.* Z8530 DRIVER FOR AX.25 -P: Joerg Reuter -M: jreuter@yaina.de +M: Joerg Reuter W: http://yaina.de/jreuter/ W: http://www.qsl.net/dl1bke/ L: linux-hams@vger.kernel.org @@ -6561,10 +5658,8 @@ F: drivers/net/hamradio/*scc.c F: drivers/net/hamradio/z8530.h ZD1211RW WIRELESS DRIVER -P: Daniel Drake -M: dsd@gentoo.org -P: Ulrich Kunitz -M: kune@deine-taler.de +M: Daniel Drake +M: Ulrich Kunitz W: http://zd1211.ath.cx/wiki/DriverRewrite L: linux-wireless@vger.kernel.org L: zd1211-devs@lists.sourceforge.net (subscribers-only) @@ -6580,14 +5675,12 @@ S: Odd Fixes F: drivers/media/video/zoran/ ZS DECSTATION Z85C30 SERIAL DRIVER -P: Maciej W. Rozycki -M: macro@linux-mips.org +M: "Maciej W. Rozycki" S: Maintained F: drivers/serial/zs.* THE REST -P: Linus Torvalds -M: torvalds@linux-foundation.org +M: Linus Torvalds L: linux-kernel@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git S: Buried alive in reporters -- GitLab From 2bed6eeb8cb0b5198d8f93e415ee595704bc3534 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Wed, 29 Jul 2009 15:04:32 -0700 Subject: [PATCH 0548/1342] MAINTAINERS: finish off the email address coalescing Add some touchups to the sample record. Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index a013e963fc0..a39f3cf940b 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -73,8 +73,8 @@ Note: For the hard of thinking, this list is meant to remain in alphabetical order. If you could add yourselves to it in alphabetical order that would be so much easier [Ed] -P: Person -M: Mail patches to +P: Person (obsolete) +M: Mail patches to: FullName L: Mailing list that is relevant to this area W: Web-page with status/info T: SCM tree type and location. Type is one of: git, hg, quilt, stgit. -- GitLab From 084bad91afd0f40ff4db9ceb56e29234c314d8d1 Mon Sep 17 00:00:00 2001 From: Kristoffer Ericson Date: Wed, 29 Jul 2009 15:04:32 -0700 Subject: [PATCH 0549/1342] MAINTAINERS: update HP Jornada 700-series and Epson s1d13xxxfb support Add the relevant git repositories and affected files to the maintainership of HP Jornada 700-series and Epson s1d13xxxfb support. Signed-off-by: Kristoffer Ericson Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index a39f3cf940b..66a3865da88 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -624,6 +624,9 @@ ARM/HP JORNADA 7XX MACHINE SUPPORT M: Kristoffer Ericson W: www.jlime.com S: Maintained +T: git git://git.kernel.org/pub/scm/linux/kernel/git/kristoffer/linux-hpc.git +F: arch/arm/mach-sa1100/jornada720.c +F: arch/arm/mach-sa1100/include/mach/jornada720.h ARM/INTEL IOP32X ARM ARCHITECTURE M: Lennert Buytenhek @@ -1900,6 +1903,7 @@ F: drivers/video/epson1355fb.c EPSON S1D13XXX FRAMEBUFFER DRIVER M: Kristoffer Ericson S: Maintained +T: git git://git.kernel.org/pub/scm/linux/kernel/git/kristoffer/linux-hpc.git F: drivers/video/s1d13xxxfb.c F: include/video/s1d13xxxfb.h -- GitLab From 5bd9052d79daa4c8beb45436c408b6de672adb82 Mon Sep 17 00:00:00 2001 From: Steve French Date: Thu, 30 Jul 2009 02:26:14 +0000 Subject: [PATCH 0550/1342] [CIFS] Updates fs/cifs/CHANGES Signed-off-by: Steve French --- fs/cifs/CHANGES | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/fs/cifs/CHANGES b/fs/cifs/CHANGES index 92888aa9074..651cefde385 100644 --- a/fs/cifs/CHANGES +++ b/fs/cifs/CHANGES @@ -1,3 +1,9 @@ +Version 1.60 +------------- +Fix memory leak in reconnect. Fix oops in DFS mount error path. +Set s_maxbytes to smaller (the max that vfs can handle) so that +sendfile will now work over cifs mounts again. + Version 1.59 ------------ Client uses server inode numbers (which are persistent) rather than -- GitLab From 5156ddce6c0a152ee7ccab2c976c6a8abc8a49b5 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Wed, 29 Jul 2009 23:04:25 -0500 Subject: [PATCH 0551/1342] powerpc/mm: Fix SMP issue with MMU context handling code In switch_mmu_context() if we call steal_context_smp() to get a context to use we shouldn't fall through and than call steal_context_up(). Doing so can be problematic in that the 'mm' that steal_context_up() ends up using will not get marked dirty in the stale_map[] for other CPUs that might have used that mm. Thus we could end up with stale TLB entries in the other CPUs that can cause all kinda of havoc. Signed-off-by: Kumar Gala --- arch/powerpc/mm/mmu_context_nohash.c | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/powerpc/mm/mmu_context_nohash.c b/arch/powerpc/mm/mmu_context_nohash.c index 92a197117d5..b1a727def15 100644 --- a/arch/powerpc/mm/mmu_context_nohash.c +++ b/arch/powerpc/mm/mmu_context_nohash.c @@ -217,6 +217,7 @@ void switch_mmu_context(struct mm_struct *prev, struct mm_struct *next) id = steal_context_smp(id); if (id == MMU_NO_CONTEXT) goto again; + goto stolen; } #endif /* CONFIG_SMP */ id = steal_context_up(id); -- GitLab From c4673f9a32d7b02bcd2057763d3d368efe5809c3 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Wed, 24 Jun 2009 20:30:28 +0400 Subject: [PATCH 0552/1342] powerpc/85xx: Fix ethernet link detection on MPC8569E-MDS boards Linux isn't able to detect link changes on ethernet ports that were used by U-Boot. This is because U-Boot wrongly clears interrupt polarity bit (INTPOL, 0x400) in the extended status register (EXT_SR, 0x1b) of Marvell PHYs. There is no easy way for PHY drivers to know IRQ line polarity (we could extract it from the device tree and pass it to phydevs, but that'll be quite a lot of work), so for now just reset the PHYs to their default states. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- arch/powerpc/platforms/85xx/mpc85xx_mds.c | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/powerpc/platforms/85xx/mpc85xx_mds.c b/arch/powerpc/platforms/85xx/mpc85xx_mds.c index 60ed9c067b1..bfb32834ab0 100644 --- a/arch/powerpc/platforms/85xx/mpc85xx_mds.c +++ b/arch/powerpc/platforms/85xx/mpc85xx_mds.c @@ -233,6 +233,19 @@ static void __init mpc85xx_mds_setup_arch(void) /* Turn UCC1 & UCC2 on */ setbits8(&bcsr_regs[8], BCSR_UCC1_GETH_EN); setbits8(&bcsr_regs[9], BCSR_UCC2_GETH_EN); + } else if (machine_is(mpc8569_mds)) { +#define BCSR7_UCC12_GETHnRST (0x1 << 2) +#define BCSR8_UEM_MARVELL_RST (0x1 << 1) + /* + * U-Boot mangles interrupt polarity for Marvell PHYs, + * so reset built-in and UEM Marvell PHYs, this puts + * the PHYs into their normal state. + */ + clrbits8(&bcsr_regs[7], BCSR7_UCC12_GETHnRST); + setbits8(&bcsr_regs[8], BCSR8_UEM_MARVELL_RST); + + setbits8(&bcsr_regs[7], BCSR7_UCC12_GETHnRST); + clrbits8(&bcsr_regs[8], BCSR8_UEM_MARVELL_RST); } iounmap(bcsr_regs); } -- GitLab From 8a0b177f367a8fd03dc5ba1f5a4494d1424471aa Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Wed, 1 Jul 2009 21:39:25 +0400 Subject: [PATCH 0553/1342] powerpc/85xx: Don't scan for TBI PHY addresses on MPC8569E-MDS boards Sometimes (e.g. when there are no UEMs attached to a board) fsl_pq_mdio_find_free() fails to find a spare address for a TBI PHY, this is because get_phy_id() returns bogus 0x0000ffff values (0xffffffff is expected), and therefore mdio bus probing fails with the following message: fsl-pq_mdio: probe of e0082120.mdio failed with error -16 And obviously ethernet doesn't work after this. This patch solves the problem by adding tbi-phy node into mdio node, so that we won't scan for spare addresses, we'll just use a fixed one. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc8569mds.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/powerpc/boot/dts/mpc8569mds.dts b/arch/powerpc/boot/dts/mpc8569mds.dts index a680165292f..9e4ce99e161 100644 --- a/arch/powerpc/boot/dts/mpc8569mds.dts +++ b/arch/powerpc/boot/dts/mpc8569mds.dts @@ -501,6 +501,10 @@ reg = <0x6>; device_type = "ethernet-phy"; }; + tbi-phy@11 { + reg = <0x11>; + device_type = "tbi-phy"; + }; }; mdio@3520 { #address-cells = <1>; -- GitLab From 1333c3d6d35bdb109ddbd4b7086cbf066a27b156 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Tue, 21 Jul 2009 01:36:43 +0400 Subject: [PATCH 0554/1342] powerpc/83xx: Fix PCI IO base address on MPC837xE-RDB boards U-Boot maps PCI IO at 0xe0300000, while current dts files specify 0xe2000000. This leads to the following oops with CONFIG_8139TOO_PIO=y. 8139too Fast Ethernet driver 0.9.28 Machine check in kernel mode. Caused by (from SRR1=41000): Transfer error ack signal Oops: Machine check, sig: 7 [#1] MPC837x RDB [...] NIP [00000900] 0x900 LR [c0439df8] rtl8139_init_board+0x238/0x524 Call Trace: [cf831d90] [c0439dcc] rtl8139_init_board+0x20c/0x524 (unreliable) [cf831de0] [c043a15c] rtl8139_init_one+0x78/0x65c [cf831e40] [c0235250] pci_call_probe+0x20/0x30 [...] This patch fixes the issue by specifying the correct PCI IO base address. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc8377_rdb.dts | 2 +- arch/powerpc/boot/dts/mpc8378_rdb.dts | 2 +- arch/powerpc/boot/dts/mpc8379_rdb.dts | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/powerpc/boot/dts/mpc8377_rdb.dts b/arch/powerpc/boot/dts/mpc8377_rdb.dts index 224b4f0704b..4f06dbc0d27 100644 --- a/arch/powerpc/boot/dts/mpc8377_rdb.dts +++ b/arch/powerpc/boot/dts/mpc8377_rdb.dts @@ -410,7 +410,7 @@ bus-range = <0 0>; ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000 - 0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>; + 0x01000000 0x0 0x00000000 0xe0300000 0x0 0x00100000>; sleep = <&pmc 0x00010000>; clock-frequency = <66666666>; #interrupt-cells = <1>; diff --git a/arch/powerpc/boot/dts/mpc8378_rdb.dts b/arch/powerpc/boot/dts/mpc8378_rdb.dts index 474ea2fa3f8..aabf3437cad 100644 --- a/arch/powerpc/boot/dts/mpc8378_rdb.dts +++ b/arch/powerpc/boot/dts/mpc8378_rdb.dts @@ -394,7 +394,7 @@ bus-range = <0 0>; ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000 - 0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>; + 0x01000000 0x0 0x00000000 0xe0300000 0x0 0x00100000>; sleep = <&pmc 0x00010000>; clock-frequency = <66666666>; #interrupt-cells = <1>; diff --git a/arch/powerpc/boot/dts/mpc8379_rdb.dts b/arch/powerpc/boot/dts/mpc8379_rdb.dts index d4838af8d37..9b1da864d89 100644 --- a/arch/powerpc/boot/dts/mpc8379_rdb.dts +++ b/arch/powerpc/boot/dts/mpc8379_rdb.dts @@ -424,7 +424,7 @@ bus-range = <0x0 0x0>; ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000 - 0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>; + 0x01000000 0x0 0x00000000 0xe0300000 0x0 0x00100000>; sleep = <&pmc 0x00010000>; clock-frequency = <66666666>; #interrupt-cells = <1>; -- GitLab From 6e900de3fff01e84c96632409359a84825c54b28 Mon Sep 17 00:00:00 2001 From: Mark Ware Date: Mon, 20 Jul 2009 21:51:03 +1000 Subject: [PATCH 0555/1342] cpm_uart: Don't use alloc_bootmem in cpm_uart_cpm2.c This is another alloc_bootmem() -> kzalloc() change, this time to fix the non-fatal badness caused when booting with a cpm2_uart console. Signed-off-by: Mark Ware Signed-off-by: Kumar Gala --- drivers/serial/cpm_uart/cpm_uart_cpm2.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm2.c b/drivers/serial/cpm_uart/cpm_uart_cpm2.c index 141c0a3333a..a9802e76b5f 100644 --- a/drivers/serial/cpm_uart/cpm_uart_cpm2.c +++ b/drivers/serial/cpm_uart/cpm_uart_cpm2.c @@ -132,7 +132,7 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con) memsz = L1_CACHE_ALIGN(pinfo->rx_nrfifos * pinfo->rx_fifosize) + L1_CACHE_ALIGN(pinfo->tx_nrfifos * pinfo->tx_fifosize); if (is_con) { - mem_addr = alloc_bootmem(memsz); + mem_addr = kzalloc(memsz, GFP_NOWAIT); dma_addr = virt_to_bus(mem_addr); } else -- GitLab From f27d4d47dcf8906c8a22908dc1d32ec641e9fbe0 Mon Sep 17 00:00:00 2001 From: Martyn Welch Date: Thu, 2 Jul 2009 15:18:35 +0100 Subject: [PATCH 0556/1342] powerpc/86xx: Update defconfig for GE Fanuc's PPC9A General update of defconfig including the following notable changes: - Enable GPIO access via sysfs on GE Fanuc's PPC9A. - Enable Highmem support. - Support for PCMCIA based daughter card. Signed-off-by: Martyn Welch Signed-off-by: Kumar Gala --- arch/powerpc/configs/86xx/gef_ppc9a_defconfig | 518 +++++++----------- 1 file changed, 196 insertions(+), 322 deletions(-) diff --git a/arch/powerpc/configs/86xx/gef_ppc9a_defconfig b/arch/powerpc/configs/86xx/gef_ppc9a_defconfig index b6a23af57f4..d8354d993b2 100644 --- a/arch/powerpc/configs/86xx/gef_ppc9a_defconfig +++ b/arch/powerpc/configs/86xx/gef_ppc9a_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:31 2009 +# Linux kernel version: 2.6.30 +# Thu Jul 2 13:55:24 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_PHYS_64BIT is not set CONFIG_ALTIVEC=y CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y CONFIG_SMP=y CONFIG_NR_CPUS=2 CONFIG_PPC32=y @@ -32,6 +34,7 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y @@ -41,7 +44,6 @@ CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_GENERIC_LOCKBREAK=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -56,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y CONFIG_GENERIC_TBSYNC=y CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -112,9 +116,7 @@ CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y -# CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -127,8 +129,15 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -143,6 +152,10 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_USE_GENERIC_SMP_HELPERS=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -156,7 +169,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -216,7 +229,7 @@ CONFIG_MPIC=y # # Kernel options # -# CONFIG_HIGHMEM is not set +CONFIG_HIGHMEM=y CONFIG_TICK_ONESHOT=y # CONFIG_NO_HZ is not set CONFIG_HIGH_RES_TIMERS=y @@ -235,6 +248,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=m # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -256,9 +270,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -285,14 +299,32 @@ CONFIG_PCI_DOMAINS=y CONFIG_PCI_SYSCALL=y CONFIG_PCIEPORTBUS=y CONFIG_PCIEAER=y +# CONFIG_PCIE_ECRC is not set +# CONFIG_PCIEAER_INJECT is not set # CONFIG_PCIEASPM is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set # CONFIG_PCI_LEGACY is not set -CONFIG_PCI_DEBUG=y # CONFIG_PCI_STUB is not set # CONFIG_PCI_IOV is not set -# CONFIG_PCCARD is not set +CONFIG_PCCARD=y +# CONFIG_PCMCIA_DEBUG is not set +CONFIG_PCMCIA=y +# CONFIG_PCMCIA_LOAD_CIS is not set +# CONFIG_PCMCIA_IOCTL is not set +# CONFIG_CARDBUS is not set + +# +# PC-card bridges +# +CONFIG_YENTA=y +# CONFIG_YENTA_O2 is not set +# CONFIG_YENTA_RICOH is not set +CONFIG_YENTA_TI=y +# CONFIG_YENTA_TOSHIBA is not set +# CONFIG_PD6729 is not set +# CONFIG_I82092 is not set +CONFIG_PCCARD_NONSTATIC=y # CONFIG_HOTPLUG_PCI is not set # CONFIG_HAS_RAPIDIO is not set @@ -353,8 +385,8 @@ CONFIG_INET_XFRM_TUNNEL=m CONFIG_INET_TUNNEL=m CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y -CONFIG_INET_XFRM_MODE_BEET=y -# CONFIG_INET_LRO is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +CONFIG_INET_LRO=y CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -380,174 +412,26 @@ CONFIG_IPV6_NDISC_NODETYPE=y CONFIG_IPV6_TUNNEL=m # CONFIG_IPV6_MULTIPLE_TABLES is not set # CONFIG_IPV6_MROUTE is not set -# CONFIG_NETLABEL is not set # CONFIG_NETWORK_SECMARK is not set -CONFIG_NETFILTER=y -# CONFIG_NETFILTER_DEBUG is not set -CONFIG_NETFILTER_ADVANCED=y -CONFIG_BRIDGE_NETFILTER=y - -# -# Core Netfilter Configuration -# -# CONFIG_NETFILTER_NETLINK_QUEUE is not set -# CONFIG_NETFILTER_NETLINK_LOG is not set -# CONFIG_NF_CONNTRACK is not set -# CONFIG_NETFILTER_TPROXY is not set -CONFIG_NETFILTER_XTABLES=m -# CONFIG_NETFILTER_XT_TARGET_CLASSIFY is not set -# CONFIG_NETFILTER_XT_TARGET_DSCP is not set -# CONFIG_NETFILTER_XT_TARGET_HL is not set -# CONFIG_NETFILTER_XT_TARGET_MARK is not set -# CONFIG_NETFILTER_XT_TARGET_NFLOG is not set -# CONFIG_NETFILTER_XT_TARGET_NFQUEUE is not set -# CONFIG_NETFILTER_XT_TARGET_RATEEST is not set -# CONFIG_NETFILTER_XT_TARGET_TRACE is not set -# CONFIG_NETFILTER_XT_TARGET_TCPMSS is not set -# CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP is not set -# CONFIG_NETFILTER_XT_MATCH_COMMENT is not set -# CONFIG_NETFILTER_XT_MATCH_DCCP is not set -# CONFIG_NETFILTER_XT_MATCH_DSCP is not set -# CONFIG_NETFILTER_XT_MATCH_ESP is not set -# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set -CONFIG_NETFILTER_XT_MATCH_HL=m -# CONFIG_NETFILTER_XT_MATCH_IPRANGE is not set -# CONFIG_NETFILTER_XT_MATCH_LENGTH is not set -# CONFIG_NETFILTER_XT_MATCH_LIMIT is not set -# CONFIG_NETFILTER_XT_MATCH_MAC is not set -# CONFIG_NETFILTER_XT_MATCH_MARK is not set -# CONFIG_NETFILTER_XT_MATCH_MULTIPORT is not set -# CONFIG_NETFILTER_XT_MATCH_OWNER is not set -# CONFIG_NETFILTER_XT_MATCH_POLICY is not set -# CONFIG_NETFILTER_XT_MATCH_PHYSDEV is not set -# CONFIG_NETFILTER_XT_MATCH_PKTTYPE is not set -# CONFIG_NETFILTER_XT_MATCH_QUOTA is not set -# CONFIG_NETFILTER_XT_MATCH_RATEEST is not set -# CONFIG_NETFILTER_XT_MATCH_REALM is not set -# CONFIG_NETFILTER_XT_MATCH_RECENT is not set -# CONFIG_NETFILTER_XT_MATCH_SCTP is not set -# CONFIG_NETFILTER_XT_MATCH_STATISTIC is not set -# CONFIG_NETFILTER_XT_MATCH_STRING is not set -# CONFIG_NETFILTER_XT_MATCH_TCPMSS is not set -# CONFIG_NETFILTER_XT_MATCH_TIME is not set -# CONFIG_NETFILTER_XT_MATCH_U32 is not set -# CONFIG_IP_VS is not set - -# -# IP: Netfilter Configuration -# -# CONFIG_NF_DEFRAG_IPV4 is not set -CONFIG_IP_NF_QUEUE=m -CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_ADDRTYPE=m -# CONFIG_IP_NF_MATCH_AH is not set -CONFIG_IP_NF_MATCH_ECN=m -CONFIG_IP_NF_MATCH_TTL=m -CONFIG_IP_NF_FILTER=m -CONFIG_IP_NF_TARGET_REJECT=m -CONFIG_IP_NF_TARGET_LOG=m -CONFIG_IP_NF_TARGET_ULOG=m -CONFIG_IP_NF_MANGLE=m -CONFIG_IP_NF_TARGET_ECN=m -# CONFIG_IP_NF_TARGET_TTL is not set -CONFIG_IP_NF_RAW=m -# CONFIG_IP_NF_SECURITY is not set -CONFIG_IP_NF_ARPTABLES=m -CONFIG_IP_NF_ARPFILTER=m -CONFIG_IP_NF_ARP_MANGLE=m - -# -# IPv6: Netfilter Configuration -# -CONFIG_IP6_NF_QUEUE=m -CONFIG_IP6_NF_IPTABLES=m -# CONFIG_IP6_NF_MATCH_AH is not set -CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_MATCH_FRAG=m -CONFIG_IP6_NF_MATCH_OPTS=m -CONFIG_IP6_NF_MATCH_HL=m -CONFIG_IP6_NF_MATCH_IPV6HEADER=m -# CONFIG_IP6_NF_MATCH_MH is not set -CONFIG_IP6_NF_MATCH_RT=m -# CONFIG_IP6_NF_TARGET_HL is not set -CONFIG_IP6_NF_TARGET_LOG=m -CONFIG_IP6_NF_FILTER=m -# CONFIG_IP6_NF_TARGET_REJECT is not set -CONFIG_IP6_NF_MANGLE=m -CONFIG_IP6_NF_RAW=m -# CONFIG_IP6_NF_SECURITY is not set -# CONFIG_BRIDGE_NF_EBTABLES is not set +# CONFIG_NETFILTER is not set # CONFIG_IP_DCCP is not set -CONFIG_IP_SCTP=m -# CONFIG_SCTP_DBG_MSG is not set -# CONFIG_SCTP_DBG_OBJCNT is not set -# CONFIG_SCTP_HMAC_NONE is not set -# CONFIG_SCTP_HMAC_SHA1 is not set -CONFIG_SCTP_HMAC_MD5=y -CONFIG_TIPC=m -# CONFIG_TIPC_ADVANCED is not set -# CONFIG_TIPC_DEBUG is not set -CONFIG_ATM=m -CONFIG_ATM_CLIP=m -# CONFIG_ATM_CLIP_NO_ICMP is not set -CONFIG_ATM_LANE=m -CONFIG_ATM_MPOA=m -CONFIG_ATM_BR2684=m -# CONFIG_ATM_BR2684_IPFILTER is not set -CONFIG_STP=m -CONFIG_BRIDGE=m +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set # CONFIG_NET_DSA is not set -CONFIG_VLAN_8021Q=m -# CONFIG_VLAN_8021Q_GVRP is not set +# CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set -CONFIG_LLC=m # CONFIG_LLC2 is not set # CONFIG_IPX is not set # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set # CONFIG_ECONET is not set -CONFIG_WAN_ROUTER=m +# CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set -CONFIG_NET_SCHED=y - -# -# Queueing/Scheduling -# -CONFIG_NET_SCH_CBQ=m -CONFIG_NET_SCH_HTB=m -CONFIG_NET_SCH_HFSC=m -CONFIG_NET_SCH_ATM=m -CONFIG_NET_SCH_PRIO=m -# CONFIG_NET_SCH_MULTIQ is not set -CONFIG_NET_SCH_RED=m -CONFIG_NET_SCH_SFQ=m -CONFIG_NET_SCH_TEQL=m -CONFIG_NET_SCH_TBF=m -CONFIG_NET_SCH_GRED=m -CONFIG_NET_SCH_DSMARK=m -CONFIG_NET_SCH_NETEM=m -# CONFIG_NET_SCH_DRR is not set - -# -# Classification -# -CONFIG_NET_CLS=y -# CONFIG_NET_CLS_BASIC is not set -CONFIG_NET_CLS_TCINDEX=m -CONFIG_NET_CLS_ROUTE4=m -CONFIG_NET_CLS_ROUTE=y -CONFIG_NET_CLS_FW=m -CONFIG_NET_CLS_U32=m -# CONFIG_CLS_U32_PERF is not set -# CONFIG_CLS_U32_MARK is not set -CONFIG_NET_CLS_RSVP=m -CONFIG_NET_CLS_RSVP6=m -# CONFIG_NET_CLS_FLOW is not set -# CONFIG_NET_EMATCH is not set -# CONFIG_NET_CLS_ACT is not set -# CONFIG_NET_CLS_IND is not set -CONFIG_NET_SCH_FIFO=y +# CONFIG_IEEE802154 is not set +# CONFIG_NET_SCHED is not set # CONFIG_DCB is not set # @@ -560,12 +444,7 @@ CONFIG_NET_PKTGEN=m # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set CONFIG_FIB_RULES=y -CONFIG_WIRELESS=y -# CONFIG_CFG80211 is not set -CONFIG_WIRELESS_OLD_REGULATORY=y -# CONFIG_WIRELESS_EXT is not set -# CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set +# CONFIG_WIRELESS is not set # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -580,9 +459,9 @@ CONFIG_WIRELESS_OLD_REGULATORY=y CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y -# CONFIG_FW_LOADER is not set -# CONFIG_DEBUG_DRIVER is not set -# CONFIG_DEBUG_DEVRES is not set +CONFIG_FW_LOADER=y +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_EXTRA_FIRMWARE="" # CONFIG_SYS_HYPERVISOR is not set # CONFIG_CONNECTOR is not set CONFIG_MTD=y @@ -672,6 +551,7 @@ CONFIG_MTD_PHYSMAP_OF=y CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -707,9 +587,60 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y -# CONFIG_IDE is not set +CONFIG_IDE=y + +# +# Please see Documentation/ide/ide.txt for help/info on IDE drives +# +# CONFIG_BLK_DEV_IDE_SATA is not set +CONFIG_IDE_GD=y +CONFIG_IDE_GD_ATA=y +# CONFIG_IDE_GD_ATAPI is not set +CONFIG_BLK_DEV_IDECS=y +# CONFIG_BLK_DEV_IDECD is not set +# CONFIG_BLK_DEV_IDETAPE is not set +# CONFIG_IDE_TASK_IOCTL is not set +CONFIG_IDE_PROC_FS=y + +# +# IDE chipset support/bugfixes +# +# CONFIG_BLK_DEV_PLATFORM is not set + +# +# PCI IDE chipsets support +# +# CONFIG_BLK_DEV_GENERIC is not set +# CONFIG_BLK_DEV_OPTI621 is not set +# CONFIG_BLK_DEV_AEC62XX is not set +# CONFIG_BLK_DEV_ALI15X3 is not set +# CONFIG_BLK_DEV_AMD74XX is not set +# CONFIG_BLK_DEV_CMD64X is not set +# CONFIG_BLK_DEV_TRIFLEX is not set +# CONFIG_BLK_DEV_CS5520 is not set +# CONFIG_BLK_DEV_CS5530 is not set +# CONFIG_BLK_DEV_HPT366 is not set +# CONFIG_BLK_DEV_JMICRON is not set +# CONFIG_BLK_DEV_SC1200 is not set +# CONFIG_BLK_DEV_PIIX is not set +# CONFIG_BLK_DEV_IT8172 is not set +# CONFIG_BLK_DEV_IT8213 is not set +# CONFIG_BLK_DEV_IT821X is not set +# CONFIG_BLK_DEV_NS87415 is not set +# CONFIG_BLK_DEV_PDC202XX_OLD is not set +# CONFIG_BLK_DEV_PDC202XX_NEW is not set +# CONFIG_BLK_DEV_SVWKS is not set +# CONFIG_BLK_DEV_SIIMAGE is not set +# CONFIG_BLK_DEV_SL82C105 is not set +# CONFIG_BLK_DEV_SLC90E66 is not set +# CONFIG_BLK_DEV_TRM290 is not set +# CONFIG_BLK_DEV_VIA82CXXX is not set +# CONFIG_BLK_DEV_TC86C001 is not set +# CONFIG_BLK_DEV_IDEDMA is not set # # SCSI device support @@ -731,10 +662,6 @@ CONFIG_BLK_DEV_SR=y # CONFIG_BLK_DEV_SR_VENDOR is not set # CONFIG_CHR_DEV_SG is not set # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -751,6 +678,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -759,6 +687,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -778,7 +707,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -791,6 +719,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_NSP32 is not set # CONFIG_SCSI_DEBUG is not set # CONFIG_SCSI_SRP is not set +# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set # CONFIG_SCSI_DH is not set # CONFIG_SCSI_OSD_INITIATOR is not set CONFIG_ATA=y @@ -842,6 +771,7 @@ CONFIG_SATA_SIL=y # CONFIG_PATA_NS87415 is not set # CONFIG_PATA_OPTI is not set # CONFIG_PATA_OPTIDMA is not set +# CONFIG_PATA_PCMCIA is not set # CONFIG_PATA_PDC_OLD is not set # CONFIG_PATA_RADISYS is not set # CONFIG_PATA_RZ1000 is not set @@ -862,14 +792,17 @@ CONFIG_SATA_SIL=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_DUMMY=m CONFIG_BONDING=m # CONFIG_MACVLAN is not set @@ -916,6 +849,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -935,8 +869,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -963,22 +899,8 @@ CONFIG_GIANFAR=y # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set # CONFIG_USB_USBNET is not set +# CONFIG_NET_PCMCIA is not set # CONFIG_WAN is not set -CONFIG_ATM_DRIVERS=y -# CONFIG_ATM_DUMMY is not set -# CONFIG_ATM_TCP is not set -# CONFIG_ATM_LANAI is not set -# CONFIG_ATM_ENI is not set -# CONFIG_ATM_FIRESTREAM is not set -# CONFIG_ATM_ZATM is not set -# CONFIG_ATM_NICSTAR is not set -# CONFIG_ATM_IDT77252 is not set -# CONFIG_ATM_AMBASSADOR is not set -# CONFIG_ATM_HORIZON is not set -# CONFIG_ATM_IA is not set -# CONFIG_ATM_FORE200E is not set -# CONFIG_ATM_HE is not set -# CONFIG_ATM_SOLOS is not set # CONFIG_FDDI is not set # CONFIG_HIPPI is not set CONFIG_PPP=m @@ -990,7 +912,6 @@ CONFIG_PPP_DEFLATE=m CONFIG_PPP_BSDCOMP=m # CONFIG_PPP_MPPE is not set CONFIG_PPPOE=m -CONFIG_PPPOATM=m # CONFIG_PPPOL2TP is not set CONFIG_SLIP=m CONFIG_SLIP_COMPRESSED=y @@ -1010,7 +931,7 @@ CONFIG_NET_POLL_CONTROLLER=y # Input device support # CONFIG_INPUT=y -CONFIG_INPUT_FF_MEMLESS=m +# CONFIG_INPUT_FF_MEMLESS is not set # CONFIG_INPUT_POLLDEV is not set # @@ -1058,6 +979,7 @@ CONFIG_DEVKMEM=y CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y # CONFIG_SERIAL_8250_PCI is not set +# CONFIG_SERIAL_8250_CS is not set CONFIG_SERIAL_8250_NR_UARTS=2 CONFIG_SERIAL_8250_RUNTIME_UARTS=2 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -1080,6 +1002,14 @@ CONFIG_HW_RANDOM=y CONFIG_NVRAM=y # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set + +# +# PCMCIA character devices +# +# CONFIG_SYNCLINK_CS is not set +# CONFIG_CARDMAN_4000 is not set +# CONFIG_CARDMAN_4040 is not set +# CONFIG_IPWIRELESS is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -1143,18 +1073,21 @@ CONFIG_DS1682=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y -# CONFIG_DEBUG_GPIO is not set -# CONFIG_GPIO_SYSFS is not set +CONFIG_GPIO_SYSFS=y # # Memory mapped GPIO expanders: @@ -1229,6 +1162,7 @@ CONFIG_SENSORS_LM92=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -1284,24 +1218,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1346,7 +1265,7 @@ CONFIG_HID_BELKIN=y CONFIG_HID_CHERRY=y CONFIG_HID_CHICONY=y CONFIG_HID_CYPRESS=y -# CONFIG_DRAGONRISE_FF is not set +# CONFIG_HID_DRAGONRISE is not set CONFIG_HID_EZKEY=y # CONFIG_HID_KYE is not set CONFIG_HID_GYRATION=y @@ -1363,10 +1282,11 @@ CONFIG_HID_PETALYNX=y CONFIG_HID_SAMSUNG=y CONFIG_HID_SONY=y CONFIG_HID_SUNPLUS=y -# CONFIG_GREENASIA_FF is not set +# CONFIG_HID_GREENASIA is not set +# CONFIG_HID_SMARTJOYPLUS is not set # CONFIG_HID_TOPSEED is not set -CONFIG_THRUSTMASTER_FF=m -CONFIG_ZEROPLUS_FF=m +# CONFIG_HID_THRUSTMASTER is not set +# CONFIG_HID_ZEROPLUS is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -1392,6 +1312,7 @@ CONFIG_USB=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y # CONFIG_USB_EHCI_ROOT_HUB_TT is not set # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1475,7 +1396,6 @@ CONFIG_USB_STORAGE=y # CONFIG_USB_IOWARRIOR is not set # CONFIG_USB_ISIGHTFW is not set # CONFIG_USB_VST is not set -# CONFIG_USB_ATM is not set # CONFIG_USB_GADGET is not set # @@ -1521,6 +1441,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set CONFIG_RTC_DRV_RX8581=y +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1548,6 +1469,10 @@ CONFIG_RTC_DRV_RX8581=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1569,10 +1494,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1589,8 +1516,11 @@ CONFIG_INOTIFY_USER=y # # CD-ROM/DVD Filesystems # -# CONFIG_ISO9660_FS is not set -# CONFIG_UDF_FS is not set +CONFIG_ISO9660_FS=y +CONFIG_JOLIET=y +CONFIG_ZISOFS=y +CONFIG_UDF_FS=y +CONFIG_UDF_NLS=y # # DOS/FAT/NT Filesystems @@ -1598,8 +1528,8 @@ CONFIG_INOTIFY_USER=y CONFIG_FAT_FS=y CONFIG_MSDOS_FS=y CONFIG_VFAT_FS=y -CONFIG_FAT_DEFAULT_CODEPAGE=437 -CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +CONFIG_FAT_DEFAULT_CODEPAGE=850 +CONFIG_FAT_DEFAULT_IOCHARSET="ascii" # CONFIG_NTFS_FS is not set # @@ -1649,6 +1579,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1723,13 +1654,13 @@ CONFIG_NLS_UTF8=m # CONFIG_BITREVERSE=y CONFIG_GENERIC_FIND_LAST_BIT=y -CONFIG_CRC_CCITT=m +CONFIG_CRC_CCITT=y # CONFIG_CRC16 is not set -# CONFIG_CRC_T10DIF is not set -# CONFIG_CRC_ITU_T is not set +CONFIG_CRC_T10DIF=y +CONFIG_CRC_ITU_T=y CONFIG_CRC32=y # CONFIG_CRC7 is not set -CONFIG_LIBCRC32C=m +CONFIG_LIBCRC32C=y CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=y CONFIG_DECOMPRESS_GZIP=y @@ -1738,6 +1669,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1750,75 +1682,24 @@ CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set -CONFIG_DEBUG_KERNEL=y -# CONFIG_DEBUG_SHIRQ is not set -CONFIG_DETECT_SOFTLOCKUP=y -# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set -CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 -CONFIG_DETECT_HUNG_TASK=y -# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set -CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0 -CONFIG_SCHED_DEBUG=y -# CONFIG_SCHEDSTATS is not set -# CONFIG_TIMER_STATS is not set -# CONFIG_DEBUG_OBJECTS is not set -# CONFIG_DEBUG_SLAB is not set -# CONFIG_DEBUG_RT_MUTEXES is not set -# CONFIG_RT_MUTEX_TESTER is not set -# CONFIG_DEBUG_SPINLOCK is not set -# CONFIG_DEBUG_MUTEXES is not set -# CONFIG_DEBUG_SPINLOCK_SLEEP is not set -# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set -# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_KERNEL is not set # CONFIG_DEBUG_BUGVERBOSE is not set -CONFIG_DEBUG_INFO=y -# CONFIG_DEBUG_VM is not set -# CONFIG_DEBUG_WRITECOUNT is not set # CONFIG_DEBUG_MEMORY_INIT is not set -# CONFIG_DEBUG_LIST is not set -# CONFIG_DEBUG_SG is not set -# CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set -# CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set -# CONFIG_BACKTRACE_SELF_TEST is not set -# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set -# CONFIG_FAULT_INJECTION is not set # CONFIG_LATENCYTOP is not set CONFIG_SYSCTL_SYSCALL_CHECK=y -# CONFIG_DEBUG_PAGEALLOC is not set CONFIG_HAVE_FUNCTION_TRACER=y CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_PREEMPT_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y -# CONFIG_KGDB is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 -# CONFIG_DEBUG_STACKOVERFLOW is not set -# CONFIG_DEBUG_STACK_USAGE is not set -# CONFIG_CODE_PATCHING_SELFTEST is not set -# CONFIG_FTR_FIXUP_SELFTEST is not set -# CONFIG_MSI_BITMAP_SELFTEST is not set -# CONFIG_XMON is not set # CONFIG_IRQSTACKS is not set -# CONFIG_BDI_SWITCH is not set # CONFIG_BOOTX_TEXT is not set # CONFIG_PPC_EARLY_DEBUG is not set @@ -1826,15 +1707,9 @@ CONFIG_PRINT_STACK_DEPTH=64 # Security options # # CONFIG_KEYS is not set -CONFIG_SECURITY=y +# CONFIG_SECURITY is not set # CONFIG_SECURITYFS is not set -CONFIG_SECURITY_NETWORK=y -# CONFIG_SECURITY_NETWORK_XFRM is not set -# CONFIG_SECURITY_PATH is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set -# CONFIG_SECURITY_ROOTPLUG is not set -CONFIG_SECURITY_DEFAULT_MMAP_MIN_ADDR=0 -# CONFIG_SECURITY_TOMOYO is not set CONFIG_CRYPTO=y # @@ -1854,11 +1729,11 @@ CONFIG_CRYPTO_PCOMP=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_MANAGER2=y # CONFIG_CRYPTO_GF128MUL is not set -CONFIG_CRYPTO_NULL=m +# CONFIG_CRYPTO_NULL is not set CONFIG_CRYPTO_WORKQUEUE=y # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_AUTHENC=m -CONFIG_CRYPTO_TEST=m +# CONFIG_CRYPTO_TEST is not set # # Authenticated Encryption with Associated Data @@ -1873,53 +1748,52 @@ CONFIG_CRYPTO_TEST=m CONFIG_CRYPTO_CBC=y # CONFIG_CRYPTO_CTR is not set # CONFIG_CRYPTO_CTS is not set -CONFIG_CRYPTO_ECB=m +# CONFIG_CRYPTO_ECB is not set # CONFIG_CRYPTO_LRW is not set -CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_PCBC is not set # CONFIG_CRYPTO_XTS is not set # # Hash modes # -CONFIG_CRYPTO_HMAC=y +CONFIG_CRYPTO_HMAC=m # CONFIG_CRYPTO_XCBC is not set # # Digest # -CONFIG_CRYPTO_CRC32C=m -CONFIG_CRYPTO_MD4=m +CONFIG_CRYPTO_CRC32C=y +# CONFIG_CRYPTO_MD4 is not set CONFIG_CRYPTO_MD5=y -CONFIG_CRYPTO_MICHAEL_MIC=m +# CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_RMD128 is not set # CONFIG_CRYPTO_RMD160 is not set # CONFIG_CRYPTO_RMD256 is not set # CONFIG_CRYPTO_RMD320 is not set CONFIG_CRYPTO_SHA1=m -CONFIG_CRYPTO_SHA256=m -CONFIG_CRYPTO_SHA512=m +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set # CONFIG_CRYPTO_TGR192 is not set -CONFIG_CRYPTO_WP512=m +# CONFIG_CRYPTO_WP512 is not set # # Ciphers # -CONFIG_CRYPTO_AES=m -CONFIG_CRYPTO_ANUBIS=m -CONFIG_CRYPTO_ARC4=m -CONFIG_CRYPTO_BLOWFISH=m +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set # CONFIG_CRYPTO_CAMELLIA is not set -CONFIG_CRYPTO_CAST5=m -CONFIG_CRYPTO_CAST6=m +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set -CONFIG_CRYPTO_KHAZAD=m +# CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_SALSA20 is not set # CONFIG_CRYPTO_SEED is not set -CONFIG_CRYPTO_SERPENT=m -CONFIG_CRYPTO_TEA=m -CONFIG_CRYPTO_TWOFISH=m -CONFIG_CRYPTO_TWOFISH_COMMON=m +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set # # Compression -- GitLab From 083e268c8b78606658f2e4524168ff45825d879e Mon Sep 17 00:00:00 2001 From: Martyn Welch Date: Thu, 2 Jul 2009 15:18:44 +0100 Subject: [PATCH 0557/1342] powerpc/86xx: Update GE Fanuc sbc310 default configuration General update of defconfig including the following notable changes: - Enable Highmem support. - Support for PCMCIA based daughter card. Signed-off-by: Martyn Welch Signed-off-by: Kumar Gala --- .../powerpc/configs/86xx/gef_sbc310_defconfig | 213 +++++++++++++----- 1 file changed, 154 insertions(+), 59 deletions(-) diff --git a/arch/powerpc/configs/86xx/gef_sbc310_defconfig b/arch/powerpc/configs/86xx/gef_sbc310_defconfig index a66910e6334..f2362e5bf06 100644 --- a/arch/powerpc/configs/86xx/gef_sbc310_defconfig +++ b/arch/powerpc/configs/86xx/gef_sbc310_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:29 2009 +# Linux kernel version: 2.6.30 +# Thu Jul 2 14:10:12 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_PHYS_64BIT is not set CONFIG_ALTIVEC=y CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y CONFIG_SMP=y CONFIG_NR_CPUS=2 CONFIG_PPC32=y @@ -32,6 +34,7 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y @@ -41,7 +44,6 @@ CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_GENERIC_LOCKBREAK=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -56,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y CONFIG_GENERIC_TBSYNC=y CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -91,7 +95,11 @@ CONFIG_CLASSIC_RCU=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 -# CONFIG_GROUP_SCHED is not set +CONFIG_GROUP_SCHED=y +CONFIG_FAIR_GROUP_SCHED=y +# CONFIG_RT_GROUP_SCHED is not set +CONFIG_USER_SCHED=y +# CONFIG_CGROUP_SCHED is not set # CONFIG_CGROUPS is not set CONFIG_SYSFS_DEPRECATED=y CONFIG_SYSFS_DEPRECATED_V2=y @@ -109,7 +117,6 @@ CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -122,8 +129,15 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -138,6 +152,10 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_USE_GENERIC_SMP_HELPERS=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -151,7 +169,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -168,7 +186,6 @@ CONFIG_DEFAULT_CFQ=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="cfq" # CONFIG_FREEZER is not set -CONFIG_PPC_MSI_BITMAP=y # # Platform support @@ -212,7 +229,7 @@ CONFIG_MPIC=y # # Kernel options # -# CONFIG_HIGHMEM is not set +CONFIG_HIGHMEM=y CONFIG_TICK_ONESHOT=y # CONFIG_NO_HZ is not set CONFIG_HIGH_RES_TIMERS=y @@ -231,6 +248,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -252,9 +270,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -281,13 +299,32 @@ CONFIG_PCI_DOMAINS=y CONFIG_PCI_SYSCALL=y CONFIG_PCIEPORTBUS=y CONFIG_PCIEAER=y +# CONFIG_PCIE_ECRC is not set +# CONFIG_PCIEAER_INJECT is not set # CONFIG_PCIEASPM is not set CONFIG_ARCH_SUPPORTS_MSI=y -CONFIG_PCI_MSI=y +# CONFIG_PCI_MSI is not set # CONFIG_PCI_LEGACY is not set # CONFIG_PCI_STUB is not set # CONFIG_PCI_IOV is not set -# CONFIG_PCCARD is not set +CONFIG_PCCARD=y +# CONFIG_PCMCIA_DEBUG is not set +CONFIG_PCMCIA=y +# CONFIG_PCMCIA_LOAD_CIS is not set +# CONFIG_PCMCIA_IOCTL is not set +# CONFIG_CARDBUS is not set + +# +# PC-card bridges +# +CONFIG_YENTA=y +# CONFIG_YENTA_O2 is not set +# CONFIG_YENTA_RICOH is not set +CONFIG_YENTA_TI=y +# CONFIG_YENTA_TOSHIBA is not set +# CONFIG_PD6729 is not set +# CONFIG_I82092 is not set +CONFIG_PCCARD_NONSTATIC=y # CONFIG_HOTPLUG_PCI is not set # CONFIG_HAS_RAPIDIO is not set @@ -393,6 +430,7 @@ CONFIG_IPV6_TUNNEL=m # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -421,7 +459,9 @@ CONFIG_FIB_RULES=y CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y -# CONFIG_FW_LOADER is not set +CONFIG_FW_LOADER=y +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_EXTRA_FIRMWARE="" # CONFIG_SYS_HYPERVISOR is not set # CONFIG_CONNECTOR is not set CONFIG_MTD=y @@ -511,6 +551,7 @@ CONFIG_MTD_PHYSMAP_OF=y CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -546,9 +587,60 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y -# CONFIG_IDE is not set +CONFIG_IDE=y + +# +# Please see Documentation/ide/ide.txt for help/info on IDE drives +# +# CONFIG_BLK_DEV_IDE_SATA is not set +CONFIG_IDE_GD=y +CONFIG_IDE_GD_ATA=y +# CONFIG_IDE_GD_ATAPI is not set +CONFIG_BLK_DEV_IDECS=y +# CONFIG_BLK_DEV_IDECD is not set +# CONFIG_BLK_DEV_IDETAPE is not set +# CONFIG_IDE_TASK_IOCTL is not set +CONFIG_IDE_PROC_FS=y + +# +# IDE chipset support/bugfixes +# +# CONFIG_BLK_DEV_PLATFORM is not set + +# +# PCI IDE chipsets support +# +# CONFIG_BLK_DEV_GENERIC is not set +# CONFIG_BLK_DEV_OPTI621 is not set +# CONFIG_BLK_DEV_AEC62XX is not set +# CONFIG_BLK_DEV_ALI15X3 is not set +# CONFIG_BLK_DEV_AMD74XX is not set +# CONFIG_BLK_DEV_CMD64X is not set +# CONFIG_BLK_DEV_TRIFLEX is not set +# CONFIG_BLK_DEV_CS5520 is not set +# CONFIG_BLK_DEV_CS5530 is not set +# CONFIG_BLK_DEV_HPT366 is not set +# CONFIG_BLK_DEV_JMICRON is not set +# CONFIG_BLK_DEV_SC1200 is not set +# CONFIG_BLK_DEV_PIIX is not set +# CONFIG_BLK_DEV_IT8172 is not set +# CONFIG_BLK_DEV_IT8213 is not set +# CONFIG_BLK_DEV_IT821X is not set +# CONFIG_BLK_DEV_NS87415 is not set +# CONFIG_BLK_DEV_PDC202XX_OLD is not set +# CONFIG_BLK_DEV_PDC202XX_NEW is not set +# CONFIG_BLK_DEV_SVWKS is not set +# CONFIG_BLK_DEV_SIIMAGE is not set +# CONFIG_BLK_DEV_SL82C105 is not set +# CONFIG_BLK_DEV_SLC90E66 is not set +# CONFIG_BLK_DEV_TRM290 is not set +# CONFIG_BLK_DEV_VIA82CXXX is not set +# CONFIG_BLK_DEV_TC86C001 is not set +# CONFIG_BLK_DEV_IDEDMA is not set # # SCSI device support @@ -570,10 +662,6 @@ CONFIG_BLK_DEV_SR=y # CONFIG_BLK_DEV_SR_VENDOR is not set # CONFIG_CHR_DEV_SG is not set # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -590,6 +678,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -598,6 +687,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -617,7 +707,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -630,6 +719,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_NSP32 is not set # CONFIG_SCSI_DEBUG is not set # CONFIG_SCSI_SRP is not set +# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set # CONFIG_SCSI_DH is not set # CONFIG_SCSI_OSD_INITIATOR is not set CONFIG_ATA=y @@ -647,14 +737,17 @@ CONFIG_SATA_SIL24=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_DUMMY=m CONFIG_BONDING=m # CONFIG_MACVLAN is not set @@ -701,6 +794,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -720,8 +814,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -748,6 +844,7 @@ CONFIG_GIANFAR=y # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set # CONFIG_USB_USBNET is not set +# CONFIG_NET_PCMCIA is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set # CONFIG_HIPPI is not set @@ -827,6 +924,7 @@ CONFIG_DEVKMEM=y CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y # CONFIG_SERIAL_8250_PCI is not set +# CONFIG_SERIAL_8250_CS is not set CONFIG_SERIAL_8250_NR_UARTS=2 CONFIG_SERIAL_8250_RUNTIME_UARTS=2 # CONFIG_SERIAL_8250_EXTENDED is not set @@ -849,6 +947,14 @@ CONFIG_HW_RANDOM=y CONFIG_NVRAM=y # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set + +# +# PCMCIA character devices +# +# CONFIG_SYNCLINK_CS is not set +# CONFIG_CARDMAN_4000 is not set +# CONFIG_CARDMAN_4040 is not set +# CONFIG_IPWIRELESS is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -912,13 +1018,17 @@ CONFIG_DS1682=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y @@ -997,6 +1107,7 @@ CONFIG_SENSORS_LM92=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -1052,24 +1163,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1114,7 +1210,7 @@ CONFIG_HID_BELKIN=y CONFIG_HID_CHERRY=y CONFIG_HID_CHICONY=y CONFIG_HID_CYPRESS=y -# CONFIG_DRAGONRISE_FF is not set +# CONFIG_HID_DRAGONRISE is not set CONFIG_HID_EZKEY=y # CONFIG_HID_KYE is not set CONFIG_HID_GYRATION=y @@ -1131,10 +1227,11 @@ CONFIG_HID_PETALYNX=y CONFIG_HID_SAMSUNG=y CONFIG_HID_SONY=y CONFIG_HID_SUNPLUS=y -# CONFIG_GREENASIA_FF is not set +# CONFIG_HID_GREENASIA is not set +# CONFIG_HID_SMARTJOYPLUS is not set # CONFIG_HID_TOPSEED is not set -# CONFIG_THRUSTMASTER_FF is not set -# CONFIG_ZEROPLUS_FF is not set +# CONFIG_HID_THRUSTMASTER is not set +# CONFIG_HID_ZEROPLUS is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -1160,6 +1257,7 @@ CONFIG_USB=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y # CONFIG_USB_EHCI_ROOT_HUB_TT is not set # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1288,6 +1386,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set CONFIG_RTC_DRV_RX8581=y +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1315,6 +1414,10 @@ CONFIG_RTC_DRV_RX8581=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1336,10 +1439,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1419,6 +1524,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1508,6 +1614,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1531,23 +1638,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_PREEMPT_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_BOOTX_TEXT is not set -- GitLab From 34466c5be4dd1490acf98e6d2ff8f3728d8ca5c1 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Wed, 29 Jul 2009 23:34:01 -0500 Subject: [PATCH 0558/1342] powerpc: Update defconfigs for embedded 6xx/7xxx, 8xx, 8{3,5,6}xxx Signed-off-by: Kumar Gala --- arch/powerpc/configs/83xx/asp8347_defconfig | 106 ++++++---- arch/powerpc/configs/83xx/kmeter1_defconfig | 176 ++++++++++------ .../configs/83xx/mpc8313_rdb_defconfig | 168 ++++++++++----- .../configs/83xx/mpc8315_rdb_defconfig | 168 ++++++++++----- .../configs/83xx/mpc832x_mds_defconfig | 111 +++++----- .../configs/83xx/mpc832x_rdb_defconfig | 120 ++++++----- .../configs/83xx/mpc834x_itx_defconfig | 114 ++++++----- .../configs/83xx/mpc834x_itxgp_defconfig | 114 ++++++----- .../configs/83xx/mpc834x_mds_defconfig | 104 ++++++---- .../configs/83xx/mpc836x_mds_defconfig | 111 +++++----- .../configs/83xx/mpc836x_rdk_defconfig | 104 ++++++---- .../configs/83xx/mpc837x_mds_defconfig | 110 +++++----- .../configs/83xx/mpc837x_rdb_defconfig | 162 ++++++++++----- arch/powerpc/configs/83xx/sbc834x_defconfig | 103 ++++++---- arch/powerpc/configs/85xx/ksi8560_defconfig | 93 ++++++--- .../configs/85xx/mpc8540_ads_defconfig | 91 ++++++--- .../configs/85xx/mpc8560_ads_defconfig | 99 +++++---- .../configs/85xx/mpc85xx_cds_defconfig | 99 +++++---- arch/powerpc/configs/85xx/sbc8548_defconfig | 96 +++++---- arch/powerpc/configs/85xx/sbc8560_defconfig | 91 ++++++--- arch/powerpc/configs/85xx/socrates_defconfig | 165 ++++++++++----- arch/powerpc/configs/85xx/stx_gp3_defconfig | 119 +++++++---- arch/powerpc/configs/85xx/tqm8540_defconfig | 100 +++++---- arch/powerpc/configs/85xx/tqm8541_defconfig | 101 +++++---- arch/powerpc/configs/85xx/tqm8548_defconfig | 100 +++++---- arch/powerpc/configs/85xx/tqm8555_defconfig | 101 +++++---- arch/powerpc/configs/85xx/tqm8560_defconfig | 101 +++++---- .../configs/85xx/xes_mpc85xx_defconfig | 118 ++++++----- arch/powerpc/configs/86xx/gef_ppc9a_defconfig | 7 +- .../powerpc/configs/86xx/gef_sbc310_defconfig | 7 +- .../powerpc/configs/86xx/gef_sbc610_defconfig | 130 +++++++----- .../configs/86xx/mpc8610_hpcd_defconfig | 118 +++++++---- .../configs/86xx/mpc8641_hpcn_defconfig | 186 ++++++++--------- arch/powerpc/configs/86xx/sbc8641d_defconfig | 112 ++++++---- arch/powerpc/configs/adder875_defconfig | 97 +++++---- arch/powerpc/configs/c2k_defconfig | 121 ++++++----- arch/powerpc/configs/ep8248e_defconfig | 97 +++++---- arch/powerpc/configs/ep88xc_defconfig | 91 ++++++--- arch/powerpc/configs/linkstation_defconfig | 116 +++++++---- arch/powerpc/configs/mgcoge_defconfig | 97 +++++---- arch/powerpc/configs/mgsuvd_defconfig | 89 ++++---- arch/powerpc/configs/mpc7448_hpc2_defconfig | 103 +++++----- arch/powerpc/configs/mpc8272_ads_defconfig | 104 ++++++---- arch/powerpc/configs/mpc83xx_defconfig | 162 ++++++++++----- arch/powerpc/configs/mpc85xx_defconfig | 193 ++++++++---------- arch/powerpc/configs/mpc85xx_smp_defconfig | 193 ++++++++---------- arch/powerpc/configs/mpc866_ads_defconfig | 92 +++++---- arch/powerpc/configs/mpc86xx_defconfig | 186 ++++++++--------- arch/powerpc/configs/mpc885_ads_defconfig | 91 ++++++--- arch/powerpc/configs/pq2fads_defconfig | 110 ++++++---- arch/powerpc/configs/prpmc2800_defconfig | 158 +++++++++----- arch/powerpc/configs/storcenter_defconfig | 108 +++++----- 52 files changed, 3639 insertions(+), 2374 deletions(-) diff --git a/arch/powerpc/configs/83xx/asp8347_defconfig b/arch/powerpc/configs/83xx/asp8347_defconfig index 27893971377..a2df0635b6d 100644 --- a/arch/powerpc/configs/83xx/asp8347_defconfig +++ b/arch/powerpc/configs/83xx/asp8347_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:05 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:02 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y CONFIG_FSL_EMB_PERFMON=y # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -53,6 +56,7 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y # CONFIG_DEFAULT_UIMAGE is not set CONFIG_REDBOOT=y CONFIG_ARCH_SUSPEND_POSSIBLE=y @@ -60,6 +64,7 @@ CONFIG_ARCH_SUSPEND_POSSIBLE=y # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -108,7 +113,6 @@ CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y # CONFIG_KALLSYMS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -121,9 +125,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -136,6 +147,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -148,7 +163,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -190,6 +205,7 @@ CONFIG_PPC_83xx=y # CONFIG_MPC837x_RDB is not set # CONFIG_SBC834x is not set CONFIG_ASP834x=y +# CONFIG_KMETER1 is not set CONFIG_PPC_MPC834x=y # CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set @@ -235,6 +251,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -255,9 +272,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -366,6 +383,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -383,7 +401,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -490,6 +512,7 @@ CONFIG_MTD_PHYSMAP_OF=y # CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -525,7 +548,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -545,14 +570,17 @@ CONFIG_HAVE_IDE=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -599,6 +627,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -618,8 +647,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -786,13 +817,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -847,6 +882,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -900,24 +936,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -960,6 +981,7 @@ CONFIG_USB_MON=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_ROOT_HUB_TT=y # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1069,6 +1091,7 @@ CONFIG_RTC_DRV_DS1374=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1096,6 +1119,10 @@ CONFIG_RTC_DRV_DS1374=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1115,10 +1142,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1192,6 +1221,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1287,6 +1317,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1312,22 +1343,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_BOOTX_TEXT is not set diff --git a/arch/powerpc/configs/83xx/kmeter1_defconfig b/arch/powerpc/configs/83xx/kmeter1_defconfig index bf0853f29f3..93ebd443a18 100644 --- a/arch/powerpc/configs/83xx/kmeter1_defconfig +++ b/arch/powerpc/configs/83xx/kmeter1_defconfig @@ -1,25 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.28 -# Fri Apr 3 10:34:33 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:03 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set +CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_FSL_EMB_PERFMON is not set # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -30,21 +33,22 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y CONFIG_EARLY_PRINTK=y CONFIG_GENERIC_NVRAM=y -CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_SCHED_OMIT_FRAME_POINTER=y CONFIG_ARCH_MAY_HAVE_PC_FDC=y CONFIG_PPC_OF=y CONFIG_OF=y @@ -52,11 +56,14 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y CONFIG_ARCH_SUSPEND_POSSIBLE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set +CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -71,19 +78,30 @@ CONFIG_LOCALVERSION_AUTO=y CONFIG_SYSVIPC=y CONFIG_SYSVIPC_SYSCTL=y CONFIG_POSIX_MQUEUE=y +CONFIG_POSIX_MQUEUE_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_AUDIT is not set + +# +# RCU Subsystem +# +CONFIG_CLASSIC_RCU=y +# CONFIG_TREE_RCU is not set +# CONFIG_PREEMPT_RCU is not set +# CONFIG_TREE_RCU_TRACE is not set +# CONFIG_PREEMPT_RCU_TRACE is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 -# CONFIG_CGROUPS is not set # CONFIG_GROUP_SCHED is not set +# CONFIG_CGROUPS is not set # CONFIG_SYSFS_DEPRECATED_V2 is not set # CONFIG_RELAY is not set # CONFIG_NAMESPACES is not set # CONFIG_BLK_DEV_INITRD is not set CONFIG_CC_OPTIMIZE_FOR_SIZE=y CONFIG_SYSCTL=y +CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y @@ -93,17 +111,23 @@ CONFIG_KALLSYMS_ALL=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y -CONFIG_COMPAT_BRK=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y -CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y +# CONFIG_STRIP_ASM_SYMS is not set +CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set @@ -116,10 +140,15 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# +# CONFIG_GCOV_KERNEL is not set +# CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y -# CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 CONFIG_MODULES=y # CONFIG_MODULE_FORCE_LOAD is not set @@ -127,11 +156,8 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set -CONFIG_KMOD=y CONFIG_BLOCK=y -# CONFIG_LBD is not set -# CONFIG_BLK_DEV_IO_TRACE is not set -# CONFIG_LSF is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -147,14 +173,11 @@ CONFIG_IOSCHED_NOOP=y # CONFIG_DEFAULT_CFQ is not set CONFIG_DEFAULT_NOOP=y CONFIG_DEFAULT_IOSCHED="noop" -CONFIG_CLASSIC_RCU=y # CONFIG_FREEZER is not set # # Platform support # -CONFIG_PPC_MULTIPLATFORM=y -CONFIG_CLASSIC32=y # CONFIG_PPC_CHRP is not set # CONFIG_MPC5121_ADS is not set # CONFIG_MPC5121_GENERIC is not set @@ -179,6 +202,8 @@ CONFIG_PPC_83xx=y CONFIG_KMETER1=y # CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set +# CONFIG_AMIGAONE is not set +CONFIG_PPC_OF_BOOT_TRAMPOLINE=y CONFIG_IPIC=y # CONFIG_MPIC is not set # CONFIG_MPIC_WEIRD is not set @@ -194,6 +219,8 @@ CONFIG_IPIC=y CONFIG_QUICC_ENGINE=y # CONFIG_QE_GPIO is not set # CONFIG_FSL_ULI1575 is not set +# CONFIG_SIMPLE_GPIO is not set +# CONFIG_MCU_MPC8349EMITX is not set # # Kernel options @@ -212,16 +239,17 @@ CONFIG_SCHED_HRTICK=y # CONFIG_PREEMPT_NONE is not set # CONFIG_PREEMPT_VOLUNTARY is not set CONFIG_PREEMPT=y -# CONFIG_PREEMPT_RCU is not set CONFIG_BINFMT_ELF=y # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y # CONFIG_KEXEC is not set +# CONFIG_CRASH_DUMP is not set CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_ARCH_POPULATES_NODE_MAP=y CONFIG_SELECT_MEMORY_MODEL=y @@ -233,12 +261,17 @@ CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_MIGRATION=y -# CONFIG_RESOURCES_64BIT is not set # CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y +CONFIG_HAVE_MLOCK=y +CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 +CONFIG_PPC_4K_PAGES=y +# CONFIG_PPC_16K_PAGES is not set +# CONFIG_PPC_64K_PAGES is not set +# CONFIG_PPC_256K_PAGES is not set CONFIG_FORCE_MAX_ZONEORDER=11 CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set @@ -331,7 +364,10 @@ CONFIG_LLC=m # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set +# CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set +# CONFIG_DCB is not set # # Network testing @@ -342,8 +378,8 @@ CONFIG_LLC=m # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set -# CONFIG_PHONET is not set # CONFIG_WIRELESS is not set +# CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -362,6 +398,7 @@ CONFIG_MTD=y # CONFIG_MTD_DEBUG is not set CONFIG_MTD_CONCAT=y CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_TESTS is not set # CONFIG_MTD_REDBOOT_PARTS is not set CONFIG_MTD_CMDLINE_PARTS=y CONFIG_MTD_OF_PARTS=y @@ -430,6 +467,11 @@ CONFIG_MTD_PHRAM=y # CONFIG_MTD_NAND is not set # CONFIG_MTD_ONENAND is not set +# +# LPDDR flash memory drivers +# +# CONFIG_MTD_LPDDR is not set + # # UBI - Unsorted block images # @@ -445,7 +487,6 @@ CONFIG_MTD_UBI_DEBUG=y # CONFIG_MTD_UBI_DEBUG_MSG is not set # CONFIG_MTD_UBI_DEBUG_PARANOID is not set # CONFIG_MTD_UBI_DEBUG_DISABLE_BGT is not set -# CONFIG_MTD_UBI_DEBUG_USERSPACE_IO is not set # CONFIG_MTD_UBI_DEBUG_EMULATE_BITFLIPS is not set # CONFIG_MTD_UBI_DEBUG_EMULATE_WRITE_FAILURES is not set # CONFIG_MTD_UBI_DEBUG_EMULATE_ERASE_FAILURES is not set @@ -459,6 +500,7 @@ CONFIG_MTD_UBI_DEBUG=y # CONFIG_MTD_UBI_DEBUG_MSG_IO is not set CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -505,10 +547,15 @@ CONFIG_MARVELL_PHY=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_REALTEK_PHY is not set +# CONFIG_NATIONAL_PHY is not set +# CONFIG_STE10XP is not set +# CONFIG_LSI_ET1011C_PHY is not set # CONFIG_FIXED_PHY is not set # CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y +# CONFIG_ETHOC is not set +# CONFIG_DNET is not set # CONFIG_IBM_NEW_EMAC_ZMII is not set # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set @@ -517,11 +564,12 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set CONFIG_NETDEV_1000=y +CONFIG_FSL_PQ_MDIO=y # CONFIG_GIANFAR is not set CONFIG_UCC_GETH=y # CONFIG_UGETH_MAGIC_PACKET is not set -# CONFIG_UGETH_FILTERING is not set # CONFIG_UGETH_TX_ON_DEMAND is not set # CONFIG_MV643XX_ETH is not set # CONFIG_NETDEV_10000 is not set @@ -531,7 +579,10 @@ CONFIG_UCC_GETH=y # # CONFIG_WLAN_PRE80211 is not set # CONFIG_WLAN_80211 is not set -# CONFIG_IWLWIFI_LEDS is not set + +# +# Enable WiMAX (Networking options) to see the WiMAX drivers +# CONFIG_WAN=y CONFIG_HDLC=y # CONFIG_HDLC_RAW is not set @@ -543,8 +594,6 @@ CONFIG_HDLC=y # # X.25/LAPB support is disabled # -CONFIG_HDLC_KM=y -CONFIG_FS_UCC_HDLC=y # CONFIG_DLCI is not set CONFIG_PPP=y CONFIG_PPP_MULTILINK=y @@ -600,16 +649,18 @@ CONFIG_SERIAL_CORE_CONSOLE=y # CONFIG_SERIAL_OF_PLATFORM is not set # CONFIG_SERIAL_QE is not set CONFIG_UNIX98_PTYS=y +# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 +# CONFIG_HVC_UDBG is not set # CONFIG_IPMI_HANDLER is not set CONFIG_HW_RANDOM=y +# CONFIG_HW_RANDOM_TIMERIOMEM is not set # CONFIG_NVRAM is not set # CONFIG_GEN_RTC is not set # CONFIG_R3964 is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set -CONFIG_BOOTCOUNT=y CONFIG_I2C=y CONFIG_I2C_BOARDINFO=y CONFIG_I2C_CHARDEV=y @@ -642,20 +693,20 @@ CONFIG_I2C_MPC=y # Miscellaneous I2C Chip support # # CONFIG_DS1682 is not set -# CONFIG_AT24 is not set -# CONFIG_SENSORS_EEPROM is not set # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_PCF8591 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set -# CONFIG_MCU_MPC8349EMITX is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -677,27 +728,15 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set +# CONFIG_TWL4030_CORE is not set # CONFIG_MFD_TMIO is not set # CONFIG_PMIC_DA903X is not set # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set +# CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -# CONFIG_DAB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -720,11 +759,16 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_EDAC is not set # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set +# CONFIG_AUXDISPLAY is not set CONFIG_UIO=y # CONFIG_UIO_PDRV is not set # CONFIG_UIO_PDRV_GENIRQ is not set # CONFIG_UIO_SMX is not set # CONFIG_UIO_SERCOS3 is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -736,9 +780,12 @@ CONFIG_UIO=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set +# CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y # CONFIG_DNOTIFY is not set CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -747,6 +794,11 @@ CONFIG_INOTIFY_USER=y # CONFIG_AUTOFS4_FS is not set # CONFIG_FUSE_FS is not set +# +# Caches +# +# CONFIG_FSCACHE is not set + # # CD-ROM/DVD Filesystems # @@ -772,10 +824,7 @@ CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set # CONFIG_CONFIGFS_FS is not set - -# -# Miscellaneous filesystems -# +CONFIG_MISC_FILESYSTEMS=y # CONFIG_ADFS_FS is not set # CONFIG_AFFS_FS is not set # CONFIG_HFS_FS is not set @@ -796,6 +845,7 @@ CONFIG_JFFS2_RTIME=y # CONFIG_JFFS2_RUBIN is not set # CONFIG_UBIFS_FS is not set # CONFIG_CRAMFS is not set +# CONFIG_SQUASHFS is not set # CONFIG_VXFS_FS is not set # CONFIG_MINIX_FS is not set # CONFIG_OMFS_FS is not set @@ -804,6 +854,7 @@ CONFIG_JFFS2_RTIME=y # CONFIG_ROMFS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set +# CONFIG_NILFS2_FS is not set CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y @@ -815,7 +866,6 @@ CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y -# CONFIG_SUNRPC_REGISTER_V4 is not set # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set @@ -845,11 +895,13 @@ CONFIG_PARTITION_ADVANCED=y # CONFIG_DLM is not set CONFIG_UCC_FAST=y CONFIG_UCC=y +# CONFIG_BINARY_PRINTF is not set # # Library routines # CONFIG_BITREVERSE=y +CONFIG_GENERIC_FIND_LAST_BIT=y # CONFIG_CRC_CCITT is not set # CONFIG_CRC16 is not set # CONFIG_CRC_T10DIF is not set @@ -859,11 +911,12 @@ CONFIG_CRC32=y # CONFIG_LIBCRC32C is not set CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=y -CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y +CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -883,13 +936,18 @@ CONFIG_DEBUG_FS=y # CONFIG_LATENCYTOP is not set CONFIG_SYSCTL_SYSCALL_CHECK=y CONFIG_HAVE_FUNCTION_TRACER=y - -# -# Tracers -# -# CONFIG_DYNAMIC_PRINTK_DEBUG is not set +CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y +CONFIG_TRACING_SUPPORT=y +# CONFIG_FTRACE is not set +# CONFIG_DYNAMIC_DEBUG is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y +CONFIG_PRINT_STACK_DEPTH=64 +# CONFIG_PPC_EMULATED_STATS is not set # CONFIG_IRQSTACKS is not set # CONFIG_VIRQ_DEBUG is not set # CONFIG_BOOTX_TEXT is not set diff --git a/arch/powerpc/configs/83xx/mpc8313_rdb_defconfig b/arch/powerpc/configs/83xx/mpc8313_rdb_defconfig index c5c0fe71a43..ff33a7db2ea 100644 --- a/arch/powerpc/configs/83xx/mpc8313_rdb_defconfig +++ b/arch/powerpc/configs/83xx/mpc8313_rdb_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:06 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:04 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_FSL_EMB_PERFMON is not set # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y CONFIG_ARCH_SUSPEND_POSSIBLE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -107,7 +112,6 @@ CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y # CONFIG_KALLSYMS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -120,9 +124,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -135,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -147,7 +162,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -189,6 +204,7 @@ CONFIG_MPC831x_RDB=y # CONFIG_MPC837x_RDB is not set # CONFIG_SBC834x is not set # CONFIG_ASP834x is not set +# CONFIG_KMETER1 is not set CONFIG_PPC_MPC831x=y # CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set @@ -234,6 +250,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -254,9 +271,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -366,6 +383,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -383,7 +401,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -503,6 +525,7 @@ CONFIG_MTD_NAND_FSL_ELBC=y CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y CONFIG_OF_SPI=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -539,7 +562,9 @@ CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_AT25 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -562,10 +587,6 @@ CONFIG_SCSI_PROC_FS=y # CONFIG_BLK_DEV_SR is not set CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -583,6 +604,7 @@ CONFIG_SCSI_SPI_ATTRS=y CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_CXGB3_ISCSI is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -591,6 +613,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -610,7 +633,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_QLOGIC_1280 is not set @@ -643,14 +665,17 @@ CONFIG_MD_RAID1=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -714,6 +739,8 @@ CONFIG_E100=y # CONFIG_SMSC9420 is not set # CONFIG_SUNDANCE is not set # CONFIG_TLAN is not set +# CONFIG_KS8842 is not set +# CONFIG_KS8851 is not set # CONFIG_VIA_RHINE is not set # CONFIG_SC92031 is not set # CONFIG_ATL2 is not set @@ -735,8 +762,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -924,7 +953,6 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set @@ -938,13 +966,18 @@ CONFIG_SPI_MASTER=y # SPI Master Controller Drivers # CONFIG_SPI_BITBANG=y -CONFIG_SPI_MPC83xx=y +# CONFIG_SPI_MPC8xxx is not set # # SPI Protocol Masters # # CONFIG_SPI_SPIDEV is not set # CONFIG_SPI_TLE62X0 is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -1002,6 +1035,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -1056,24 +1090,10 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set +# CONFIG_EZX_PCAP is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1135,6 +1155,7 @@ CONFIG_USB_MON=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_ROOT_HUB_TT=y # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1144,9 +1165,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=y -CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PPC_OF_BE=y # CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set +CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PCI=y CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y @@ -1235,8 +1256,9 @@ CONFIG_USB_GADGET_SELECTED=y # CONFIG_USB_GADGET_OMAP is not set # CONFIG_USB_GADGET_PXA25X is not set # CONFIG_USB_GADGET_PXA27X is not set -# CONFIG_USB_GADGET_S3C2410 is not set +# CONFIG_USB_GADGET_S3C_HSOTG is not set # CONFIG_USB_GADGET_IMX is not set +# CONFIG_USB_GADGET_S3C2410 is not set # CONFIG_USB_GADGET_M66592 is not set # CONFIG_USB_GADGET_AMD5536UDC is not set # CONFIG_USB_GADGET_FSL_QE is not set @@ -1244,9 +1266,11 @@ CONFIG_USB_GADGET_SELECTED=y CONFIG_USB_GADGET_NET2280=y CONFIG_USB_NET2280=y # CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LANGWELL is not set # CONFIG_USB_GADGET_DUMMY_HCD is not set CONFIG_USB_GADGET_DUALSPEED=y # CONFIG_USB_ZERO is not set +# CONFIG_USB_AUDIO is not set CONFIG_USB_ETH=y CONFIG_USB_ETH_RNDIS=y # CONFIG_USB_GADGETFS is not set @@ -1298,6 +1322,7 @@ CONFIG_RTC_DRV_DS1307=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1332,6 +1357,10 @@ CONFIG_RTC_DRV_DS1307=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1351,10 +1380,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1428,6 +1459,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1464,7 +1496,46 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set -# CONFIG_NLS is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +# CONFIG_NLS_CODEPAGE_437 is not set +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +# CONFIG_NLS_ISO8859_1 is not set +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set # CONFIG_DLM is not set # CONFIG_BINARY_PRINTF is not set @@ -1488,6 +1559,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1518,6 +1590,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -1529,7 +1604,6 @@ CONFIG_SCHED_DEBUG=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -1543,16 +1617,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -1560,6 +1633,9 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set diff --git a/arch/powerpc/configs/83xx/mpc8315_rdb_defconfig b/arch/powerpc/configs/83xx/mpc8315_rdb_defconfig index af4952feba3..76237d46670 100644 --- a/arch/powerpc/configs/83xx/mpc8315_rdb_defconfig +++ b/arch/powerpc/configs/83xx/mpc8315_rdb_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:06 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:05 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_FSL_EMB_PERFMON is not set # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y CONFIG_ARCH_SUSPEND_POSSIBLE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -107,7 +112,6 @@ CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y # CONFIG_KALLSYMS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -120,9 +124,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -135,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -147,7 +162,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -189,6 +204,7 @@ CONFIG_MPC831x_RDB=y # CONFIG_MPC837x_RDB is not set # CONFIG_SBC834x is not set # CONFIG_ASP834x is not set +# CONFIG_KMETER1 is not set CONFIG_PPC_MPC831x=y # CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set @@ -234,6 +250,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -254,9 +271,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -366,6 +383,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -383,7 +401,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -503,6 +525,7 @@ CONFIG_MTD_NAND_IDS=y CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y CONFIG_OF_SPI=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -539,7 +562,9 @@ CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_AT25 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -562,10 +587,6 @@ CONFIG_SCSI_PROC_FS=y # CONFIG_BLK_DEV_SR is not set CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -583,6 +604,7 @@ CONFIG_SCSI_SPI_ATTRS=y CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_CXGB3_ISCSI is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -591,6 +613,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -610,7 +633,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -704,14 +726,17 @@ CONFIG_MD_RAID1=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -775,6 +800,8 @@ CONFIG_E100=y # CONFIG_SMSC9420 is not set # CONFIG_SUNDANCE is not set # CONFIG_TLAN is not set +# CONFIG_KS8842 is not set +# CONFIG_KS8851 is not set # CONFIG_VIA_RHINE is not set # CONFIG_SC92031 is not set # CONFIG_ATL2 is not set @@ -796,8 +823,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -985,7 +1014,6 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set @@ -999,13 +1027,18 @@ CONFIG_SPI_MASTER=y # SPI Master Controller Drivers # CONFIG_SPI_BITBANG=y -CONFIG_SPI_MPC83xx=y +# CONFIG_SPI_MPC8xxx is not set # # SPI Protocol Masters # # CONFIG_SPI_SPIDEV is not set # CONFIG_SPI_TLE62X0 is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -1063,6 +1096,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -1117,24 +1151,10 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set +# CONFIG_EZX_PCAP is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1196,6 +1216,7 @@ CONFIG_USB_MON=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_ROOT_HUB_TT=y # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1205,9 +1226,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=y -CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PPC_OF_BE=y # CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set +CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PCI=y CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y @@ -1296,8 +1317,9 @@ CONFIG_USB_GADGET_SELECTED=y # CONFIG_USB_GADGET_OMAP is not set # CONFIG_USB_GADGET_PXA25X is not set # CONFIG_USB_GADGET_PXA27X is not set -# CONFIG_USB_GADGET_S3C2410 is not set +# CONFIG_USB_GADGET_S3C_HSOTG is not set # CONFIG_USB_GADGET_IMX is not set +# CONFIG_USB_GADGET_S3C2410 is not set # CONFIG_USB_GADGET_M66592 is not set # CONFIG_USB_GADGET_AMD5536UDC is not set # CONFIG_USB_GADGET_FSL_QE is not set @@ -1305,9 +1327,11 @@ CONFIG_USB_GADGET_SELECTED=y CONFIG_USB_GADGET_NET2280=y CONFIG_USB_NET2280=y # CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LANGWELL is not set # CONFIG_USB_GADGET_DUMMY_HCD is not set CONFIG_USB_GADGET_DUALSPEED=y # CONFIG_USB_ZERO is not set +# CONFIG_USB_AUDIO is not set CONFIG_USB_ETH=y CONFIG_USB_ETH_RNDIS=y # CONFIG_USB_GADGETFS is not set @@ -1359,6 +1383,7 @@ CONFIG_RTC_DRV_DS1307=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1393,6 +1418,10 @@ CONFIG_RTC_DRV_DS1307=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1412,10 +1441,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1489,6 +1520,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1525,7 +1557,46 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set -# CONFIG_NLS is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +# CONFIG_NLS_CODEPAGE_437 is not set +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +# CONFIG_NLS_ISO8859_1 is not set +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set # CONFIG_DLM is not set # CONFIG_BINARY_PRINTF is not set @@ -1549,6 +1620,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1579,6 +1651,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -1590,7 +1665,6 @@ CONFIG_SCHED_DEBUG=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -1604,16 +1678,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -1621,6 +1694,9 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set diff --git a/arch/powerpc/configs/83xx/mpc832x_mds_defconfig b/arch/powerpc/configs/83xx/mpc832x_mds_defconfig index 8c8f660b4fc..e0e36a11340 100644 --- a/arch/powerpc/configs/83xx/mpc832x_mds_defconfig +++ b/arch/powerpc/configs/83xx/mpc832x_mds_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:07 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:06 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_FSL_EMB_PERFMON is not set # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y CONFIG_ARCH_SUSPEND_POSSIBLE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -107,7 +112,6 @@ CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y # CONFIG_KALLSYMS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -120,9 +124,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -135,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -147,7 +162,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -189,6 +204,7 @@ CONFIG_MPC832x_MDS=y # CONFIG_MPC837x_RDB is not set # CONFIG_SBC834x is not set # CONFIG_ASP834x is not set +# CONFIG_KMETER1 is not set CONFIG_PPC_MPC832x=y # CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set @@ -235,6 +251,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -255,9 +272,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -366,6 +383,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -383,7 +401,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -404,6 +426,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_MTD is not set CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -438,7 +461,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -461,10 +486,6 @@ CONFIG_SCSI_PROC_FS=y # CONFIG_BLK_DEV_SR is not set # CONFIG_CHR_DEV_SG is not set # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -482,6 +503,7 @@ CONFIG_SCSI_WAIT_SCAN=m CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_CXGB3_ISCSI is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -490,6 +512,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -509,7 +532,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_QLOGIC_1280 is not set @@ -532,14 +554,17 @@ CONFIG_SCSI_LOWLEVEL=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -586,6 +611,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -605,11 +631,13 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y # CONFIG_GIANFAR is not set CONFIG_UCC_GETH=y # CONFIG_UGETH_MAGIC_PACKET is not set # CONFIG_UGETH_TX_ON_DEMAND is not set +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -787,13 +815,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -848,6 +880,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -896,23 +929,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -996,6 +1015,7 @@ CONFIG_RTC_DRV_DS1374=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1023,6 +1043,10 @@ CONFIG_RTC_DRV_DS1374=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1042,10 +1066,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1108,6 +1134,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1165,6 +1192,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1190,22 +1218,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_BOOTX_TEXT is not set diff --git a/arch/powerpc/configs/83xx/mpc832x_rdb_defconfig b/arch/powerpc/configs/83xx/mpc832x_rdb_defconfig index 227dbba7679..4f27d454822 100644 --- a/arch/powerpc/configs/83xx/mpc832x_rdb_defconfig +++ b/arch/powerpc/configs/83xx/mpc832x_rdb_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:08 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:07 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_FSL_EMB_PERFMON is not set # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y CONFIG_ARCH_SUSPEND_POSSIBLE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -107,7 +112,6 @@ CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y # CONFIG_KALLSYMS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -120,9 +124,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -135,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -147,7 +162,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -189,6 +204,7 @@ CONFIG_MPC832x_RDB=y # CONFIG_MPC837x_RDB is not set # CONFIG_SBC834x is not set # CONFIG_ASP834x is not set +# CONFIG_KMETER1 is not set CONFIG_PPC_MPC832x=y # CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set @@ -235,6 +251,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -255,9 +272,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -366,6 +383,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -383,7 +401,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -405,6 +427,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y CONFIG_OF_SPI=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -441,7 +464,9 @@ CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_AT25 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -464,10 +489,6 @@ CONFIG_BLK_DEV_SD=y # CONFIG_BLK_DEV_SR is not set # CONFIG_CHR_DEV_SG is not set # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -485,6 +506,7 @@ CONFIG_SCSI_WAIT_SCAN=m CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_CXGB3_ISCSI is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -493,6 +515,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -512,7 +535,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_QLOGIC_1280 is not set @@ -535,14 +557,17 @@ CONFIG_SCSI_LOWLEVEL=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -590,6 +615,8 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set +# CONFIG_KS8851 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -609,11 +636,13 @@ CONFIG_E1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y # CONFIG_GIANFAR is not set CONFIG_UCC_GETH=y # CONFIG_UGETH_MAGIC_PACKET is not set # CONFIG_UGETH_TX_ON_DEMAND is not set +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -804,7 +833,6 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set @@ -817,13 +845,18 @@ CONFIG_SPI_MASTER=y # SPI Master Controller Drivers # CONFIG_SPI_BITBANG=y -CONFIG_SPI_MPC83xx=y +# CONFIG_SPI_MPC8xxx is not set # # SPI Protocol Masters # # CONFIG_SPI_SPIDEV is not set # CONFIG_SPI_TLE62X0 is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -881,6 +914,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -935,24 +969,10 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set +# CONFIG_EZX_PCAP is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1014,6 +1034,7 @@ CONFIG_USB_MON=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y # CONFIG_USB_EHCI_ROOT_HUB_TT is not set # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1023,9 +1044,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=y -CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PPC_OF_BE=y # CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set +CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PCI=y CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y @@ -1127,6 +1148,8 @@ CONFIG_MMC_BLOCK_BOUNCE=y # CONFIG_MMC_WBSD is not set # CONFIG_MMC_TIFM_SD is not set CONFIG_MMC_SPI=y +# CONFIG_MMC_CB710 is not set +# CONFIG_MMC_VIA_SDMMC is not set # CONFIG_MEMSTICK is not set # CONFIG_NEW_LEDS is not set # CONFIG_ACCESSIBILITY is not set @@ -1136,6 +1159,10 @@ CONFIG_MMC_SPI=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1155,10 +1182,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1224,6 +1253,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1325,6 +1355,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1350,22 +1381,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_BOOTX_TEXT is not set diff --git a/arch/powerpc/configs/83xx/mpc834x_itx_defconfig b/arch/powerpc/configs/83xx/mpc834x_itx_defconfig index 24ee7fcac87..648dac0c9d8 100644 --- a/arch/powerpc/configs/83xx/mpc834x_itx_defconfig +++ b/arch/powerpc/configs/83xx/mpc834x_itx_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:09 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:07 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_FSL_EMB_PERFMON is not set # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y CONFIG_ARCH_SUSPEND_POSSIBLE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -107,7 +112,6 @@ CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y # CONFIG_KALLSYMS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -120,9 +124,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -135,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -147,7 +162,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -189,6 +204,7 @@ CONFIG_MPC834x_ITX=y # CONFIG_MPC837x_RDB is not set # CONFIG_SBC834x is not set # CONFIG_ASP834x is not set +# CONFIG_KMETER1 is not set CONFIG_PPC_MPC834x=y # CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set @@ -234,6 +250,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -254,9 +271,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -365,6 +382,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -382,7 +400,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -487,6 +509,7 @@ CONFIG_MTD_PHYSMAP=y CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y CONFIG_OF_SPI=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -523,7 +546,9 @@ CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_AT25 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y CONFIG_IDE=y @@ -594,10 +619,6 @@ CONFIG_BLK_DEV_SD=y # CONFIG_BLK_DEV_SR is not set CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -615,6 +636,7 @@ CONFIG_SCSI_SPI_ATTRS=y CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_CXGB3_ISCSI is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -623,6 +645,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -642,7 +665,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -737,14 +759,17 @@ CONFIG_MD_RAID1=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -791,8 +816,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -960,7 +987,6 @@ CONFIG_I2C_MPC=y CONFIG_SENSORS_PCF8574=y # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set @@ -973,13 +999,18 @@ CONFIG_SPI_MASTER=y # SPI Master Controller Drivers # CONFIG_SPI_BITBANG=y -CONFIG_SPI_MPC83xx=y +# CONFIG_SPI_MPC8xxx is not set # # SPI Protocol Masters # # CONFIG_SPI_SPIDEV is not set # CONFIG_SPI_TLE62X0 is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -1026,24 +1057,10 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set +# CONFIG_EZX_PCAP is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1085,6 +1102,7 @@ CONFIG_USB_MON=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_ROOT_HUB_TT=y # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1208,6 +1226,7 @@ CONFIG_RTC_DRV_DS1307=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1242,6 +1261,10 @@ CONFIG_RTC_DRV_DS1307=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1261,10 +1284,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1331,6 +1356,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1429,6 +1455,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1454,22 +1481,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_BOOTX_TEXT is not set diff --git a/arch/powerpc/configs/83xx/mpc834x_itxgp_defconfig b/arch/powerpc/configs/83xx/mpc834x_itxgp_defconfig index 7f39543205a..bf6deb831dc 100644 --- a/arch/powerpc/configs/83xx/mpc834x_itxgp_defconfig +++ b/arch/powerpc/configs/83xx/mpc834x_itxgp_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:10 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:08 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_FSL_EMB_PERFMON is not set # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y CONFIG_ARCH_SUSPEND_POSSIBLE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -107,7 +112,6 @@ CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y # CONFIG_KALLSYMS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -120,9 +124,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -135,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -147,7 +162,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -189,6 +204,7 @@ CONFIG_MPC834x_ITX=y # CONFIG_MPC837x_RDB is not set # CONFIG_SBC834x is not set # CONFIG_ASP834x is not set +# CONFIG_KMETER1 is not set CONFIG_PPC_MPC834x=y # CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set @@ -234,6 +250,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -254,9 +271,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -365,6 +382,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -382,7 +400,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -487,6 +509,7 @@ CONFIG_MTD_PHYSMAP=y CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y CONFIG_OF_SPI=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -523,7 +546,9 @@ CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_AT25 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -546,10 +571,6 @@ CONFIG_BLK_DEV_SD=y # CONFIG_BLK_DEV_SR is not set CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -567,6 +588,7 @@ CONFIG_SCSI_SPI_ATTRS=y CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_CXGB3_ISCSI is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -575,6 +597,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -594,7 +617,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_QLOGIC_1280 is not set @@ -617,14 +639,17 @@ CONFIG_SCSI_LOWLEVEL=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -671,8 +696,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -840,7 +867,6 @@ CONFIG_I2C_MPC=y CONFIG_SENSORS_PCF8574=y # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set @@ -853,13 +879,18 @@ CONFIG_SPI_MASTER=y # SPI Master Controller Drivers # CONFIG_SPI_BITBANG=y -CONFIG_SPI_MPC83xx=y +# CONFIG_SPI_MPC8xxx is not set # # SPI Protocol Masters # # CONFIG_SPI_SPIDEV is not set # CONFIG_SPI_TLE62X0 is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -906,24 +937,10 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set +# CONFIG_EZX_PCAP is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -965,6 +982,7 @@ CONFIG_USB_MON=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_ROOT_HUB_TT=y # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1087,6 +1105,7 @@ CONFIG_RTC_DRV_DS1307=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1121,6 +1140,10 @@ CONFIG_RTC_DRV_DS1307=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1140,10 +1163,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1210,6 +1235,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1308,6 +1334,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1333,22 +1360,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_BOOTX_TEXT is not set diff --git a/arch/powerpc/configs/83xx/mpc834x_mds_defconfig b/arch/powerpc/configs/83xx/mpc834x_mds_defconfig index 1cd1fcac22c..3236c47712c 100644 --- a/arch/powerpc/configs/83xx/mpc834x_mds_defconfig +++ b/arch/powerpc/configs/83xx/mpc834x_mds_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:11 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:09 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_FSL_EMB_PERFMON is not set # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y CONFIG_ARCH_SUSPEND_POSSIBLE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -107,7 +112,6 @@ CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y # CONFIG_KALLSYMS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -120,9 +124,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -135,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -147,7 +162,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -189,6 +204,7 @@ CONFIG_MPC834x_MDS=y # CONFIG_MPC837x_RDB is not set # CONFIG_SBC834x is not set # CONFIG_ASP834x is not set +# CONFIG_KMETER1 is not set CONFIG_PPC_MPC834x=y # CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set @@ -234,6 +250,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -254,9 +271,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -365,6 +382,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -382,7 +400,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -403,6 +425,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_MTD is not set CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -437,7 +460,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -457,14 +482,17 @@ CONFIG_HAVE_IDE=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -527,6 +555,7 @@ CONFIG_E100=y # CONFIG_SMSC9420 is not set # CONFIG_SUNDANCE is not set # CONFIG_TLAN is not set +# CONFIG_KS8842 is not set # CONFIG_VIA_RHINE is not set # CONFIG_SC92031 is not set # CONFIG_ATL2 is not set @@ -548,8 +577,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -724,13 +755,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -785,6 +820,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -833,23 +869,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -933,6 +955,7 @@ CONFIG_RTC_DRV_DS1374=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -960,6 +983,10 @@ CONFIG_RTC_DRV_DS1374=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -979,10 +1006,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1045,6 +1074,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1100,6 +1130,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1125,22 +1156,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_BOOTX_TEXT is not set diff --git a/arch/powerpc/configs/83xx/mpc836x_mds_defconfig b/arch/powerpc/configs/83xx/mpc836x_mds_defconfig index ce5177393a0..8c5299d7481 100644 --- a/arch/powerpc/configs/83xx/mpc836x_mds_defconfig +++ b/arch/powerpc/configs/83xx/mpc836x_mds_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:12 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:10 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_FSL_EMB_PERFMON is not set # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y CONFIG_ARCH_SUSPEND_POSSIBLE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -107,7 +112,6 @@ CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y # CONFIG_KALLSYMS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -120,9 +124,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -135,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -147,7 +162,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -189,6 +204,7 @@ CONFIG_MPC836x_MDS=y # CONFIG_MPC837x_RDB is not set # CONFIG_SBC834x is not set # CONFIG_ASP834x is not set +# CONFIG_KMETER1 is not set # CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set # CONFIG_AMIGAONE is not set @@ -233,6 +249,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -253,9 +270,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -364,6 +381,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -381,7 +399,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -485,6 +507,7 @@ CONFIG_MTD_PHYSMAP_OF=y # CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -519,7 +542,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -542,10 +567,6 @@ CONFIG_SCSI_PROC_FS=y # CONFIG_BLK_DEV_SR is not set # CONFIG_CHR_DEV_SG is not set # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -563,6 +584,7 @@ CONFIG_SCSI_WAIT_SCAN=m CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_CXGB3_ISCSI is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -571,6 +593,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -590,7 +613,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_QLOGIC_1280 is not set @@ -613,14 +635,17 @@ CONFIG_SCSI_LOWLEVEL=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -667,6 +692,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -686,11 +712,13 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y # CONFIG_GIANFAR is not set CONFIG_UCC_GETH=y # CONFIG_UGETH_MAGIC_PACKET is not set # CONFIG_UGETH_TX_ON_DEMAND is not set +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -868,13 +896,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -929,6 +961,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -977,23 +1010,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1077,6 +1096,7 @@ CONFIG_RTC_DRV_DS1374=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1104,6 +1124,10 @@ CONFIG_RTC_DRV_DS1374=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1123,10 +1147,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1190,6 +1216,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1247,6 +1274,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1272,22 +1300,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_BOOTX_TEXT is not set diff --git a/arch/powerpc/configs/83xx/mpc836x_rdk_defconfig b/arch/powerpc/configs/83xx/mpc836x_rdk_defconfig index 7f1d1383a24..ff31667a890 100644 --- a/arch/powerpc/configs/83xx/mpc836x_rdk_defconfig +++ b/arch/powerpc/configs/83xx/mpc836x_rdk_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:13 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:12 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_FSL_EMB_PERFMON is not set # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -54,12 +57,14 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y CONFIG_ARCH_SUSPEND_POSSIBLE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -108,7 +113,6 @@ CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y # CONFIG_KALLSYMS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -121,9 +125,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -136,6 +147,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -148,7 +163,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -190,6 +205,7 @@ CONFIG_MPC836x_RDK=y # CONFIG_MPC837x_RDB is not set # CONFIG_SBC834x is not set # CONFIG_ASP834x is not set +# CONFIG_KMETER1 is not set # CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set # CONFIG_AMIGAONE is not set @@ -233,6 +249,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -253,9 +270,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -366,6 +383,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -383,7 +401,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -498,6 +520,7 @@ CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y CONFIG_OF_I2C=y CONFIG_OF_SPI=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -533,7 +556,9 @@ CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_AT25 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -553,14 +578,17 @@ CONFIG_HAVE_IDE=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -607,11 +635,13 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y # CONFIG_GIANFAR is not set CONFIG_UCC_GETH=y # CONFIG_UGETH_MAGIC_PACKET is not set # CONFIG_UGETH_TX_ON_DEMAND is not set +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -777,7 +807,6 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set @@ -791,13 +820,18 @@ CONFIG_SPI_MASTER=y # CONFIG_SPI_BITBANG=y # CONFIG_SPI_GPIO is not set -CONFIG_SPI_MPC83xx=y +# CONFIG_SPI_MPC8xxx is not set # # SPI Protocol Masters # CONFIG_SPI_SPIDEV=y # CONFIG_SPI_TLE62X0 is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y @@ -865,23 +899,10 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set +# CONFIG_EZX_PCAP is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -990,6 +1011,10 @@ CONFIG_HID=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1009,10 +1034,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1086,6 +1113,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1145,6 +1173,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1170,22 +1199,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_BOOTX_TEXT is not set diff --git a/arch/powerpc/configs/83xx/mpc837x_mds_defconfig b/arch/powerpc/configs/83xx/mpc837x_mds_defconfig index bf636fd560a..e285ec0fe95 100644 --- a/arch/powerpc/configs/83xx/mpc837x_mds_defconfig +++ b/arch/powerpc/configs/83xx/mpc837x_mds_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:12 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:11 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_FSL_EMB_PERFMON is not set # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y CONFIG_ARCH_SUSPEND_POSSIBLE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -108,7 +113,6 @@ CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -121,8 +125,15 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -136,6 +147,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -148,7 +163,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -190,6 +205,7 @@ CONFIG_MPC837x_MDS=y # CONFIG_MPC837x_RDB is not set # CONFIG_SBC834x is not set # CONFIG_ASP834x is not set +# CONFIG_KMETER1 is not set CONFIG_PPC_MPC837x=y # CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set @@ -234,6 +250,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -254,9 +271,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -365,6 +382,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -382,7 +400,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -403,6 +425,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_MTD is not set CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -437,7 +460,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -460,10 +485,6 @@ CONFIG_BLK_DEV_SD=y # CONFIG_BLK_DEV_SR is not set CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -481,6 +502,7 @@ CONFIG_SCSI_WAIT_SCAN=m CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_CXGB3_ISCSI is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -489,6 +511,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -508,7 +531,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -592,14 +614,17 @@ CONFIG_ATA_SFF=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -646,6 +671,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -665,8 +691,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -844,13 +872,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -905,6 +937,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -953,23 +986,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1026,6 +1045,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1045,10 +1068,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1111,6 +1136,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1170,6 +1196,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1193,22 +1220,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_BOOTX_TEXT is not set diff --git a/arch/powerpc/configs/83xx/mpc837x_rdb_defconfig b/arch/powerpc/configs/83xx/mpc837x_rdb_defconfig index fe6454eacbd..1ab3e4cd301 100644 --- a/arch/powerpc/configs/83xx/mpc837x_rdb_defconfig +++ b/arch/powerpc/configs/83xx/mpc837x_rdb_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:14 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:13 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_FSL_EMB_PERFMON is not set # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y CONFIG_ARCH_SUSPEND_POSSIBLE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -108,7 +113,6 @@ CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -121,8 +125,15 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -136,6 +147,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -148,7 +163,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -190,6 +205,7 @@ CONFIG_PPC_83xx=y CONFIG_MPC837x_RDB=y # CONFIG_SBC834x is not set # CONFIG_ASP834x is not set +# CONFIG_KMETER1 is not set CONFIG_PPC_MPC837x=y # CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set @@ -234,6 +250,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -254,9 +271,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -360,6 +377,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -377,7 +395,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -398,6 +420,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_MTD is not set CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -433,7 +456,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -456,10 +481,6 @@ CONFIG_BLK_DEV_SD=y # CONFIG_BLK_DEV_SR is not set CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -476,6 +497,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -484,6 +506,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -503,7 +526,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -598,14 +620,17 @@ CONFIG_MD_RAID6_PQ=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -652,6 +677,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -671,8 +697,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -842,13 +870,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -903,6 +935,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -956,24 +989,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1011,7 +1029,7 @@ CONFIG_HID_BELKIN=y CONFIG_HID_CHERRY=y CONFIG_HID_CHICONY=y CONFIG_HID_CYPRESS=y -# CONFIG_DRAGONRISE_FF is not set +# CONFIG_HID_DRAGONRISE is not set CONFIG_HID_EZKEY=y # CONFIG_HID_KYE is not set CONFIG_HID_GYRATION=y @@ -1028,10 +1046,11 @@ CONFIG_HID_PETALYNX=y CONFIG_HID_SAMSUNG=y CONFIG_HID_SONY=y CONFIG_HID_SUNPLUS=y -# CONFIG_GREENASIA_FF is not set +# CONFIG_HID_GREENASIA is not set +# CONFIG_HID_SMARTJOYPLUS is not set # CONFIG_HID_TOPSEED is not set -CONFIG_THRUSTMASTER_FF=m -CONFIG_ZEROPLUS_FF=m +# CONFIG_HID_THRUSTMASTER is not set +# CONFIG_HID_ZEROPLUS is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -1057,6 +1076,7 @@ CONFIG_USB_MON=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_ROOT_HUB_TT=y # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1141,6 +1161,10 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1160,10 +1184,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1226,6 +1252,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1262,7 +1289,46 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set -# CONFIG_NLS is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +# CONFIG_NLS_CODEPAGE_437 is not set +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +# CONFIG_NLS_ISO8859_1 is not set +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set # CONFIG_DLM is not set # CONFIG_BINARY_PRINTF is not set @@ -1285,6 +1351,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1308,22 +1375,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_BOOTX_TEXT is not set diff --git a/arch/powerpc/configs/83xx/sbc834x_defconfig b/arch/powerpc/configs/83xx/sbc834x_defconfig index fe08f672cb2..a592b5efdc4 100644 --- a/arch/powerpc/configs/83xx/sbc834x_defconfig +++ b/arch/powerpc/configs/83xx/sbc834x_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:15 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:13 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_FSL_EMB_PERFMON is not set # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y CONFIG_ARCH_SUSPEND_POSSIBLE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -107,7 +112,6 @@ CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y # CONFIG_KALLSYMS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -120,8 +124,15 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -134,6 +145,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -146,7 +161,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -188,6 +203,7 @@ CONFIG_PPC_83xx=y # CONFIG_MPC837x_RDB is not set CONFIG_SBC834x=y # CONFIG_ASP834x is not set +# CONFIG_KMETER1 is not set CONFIG_PPC_MPC834x=y # CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set @@ -232,6 +248,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -252,9 +269,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -363,6 +380,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -380,7 +398,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -401,6 +423,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_MTD is not set CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -435,7 +458,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -455,14 +480,17 @@ CONFIG_HAVE_IDE=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -509,6 +537,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -528,8 +557,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -688,13 +719,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -749,6 +784,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -797,23 +833,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -# CONFIG_DAB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -851,6 +873,10 @@ CONFIG_HID=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -862,10 +888,12 @@ CONFIG_HID=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -928,6 +956,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -971,6 +1000,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -994,22 +1024,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_BOOTX_TEXT is not set diff --git a/arch/powerpc/configs/85xx/ksi8560_defconfig b/arch/powerpc/configs/85xx/ksi8560_defconfig index 09146ddaa3c..ff04e1028f5 100644 --- a/arch/powerpc/configs/85xx/ksi8560_defconfig +++ b/arch/powerpc/configs/85xx/ksi8560_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:16 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:14 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set CONFIG_PPC_85xx=y # CONFIG_PPC_8xx is not set # CONFIG_40x is not set @@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -57,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -108,7 +111,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -121,8 +123,15 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -136,6 +145,11 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# +# CONFIG_GCOV_KERNEL is not set # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -143,7 +157,7 @@ CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -176,6 +190,7 @@ CONFIG_MPC85xx=y # CONFIG_MPC85xx_DS is not set # CONFIG_SOCRATES is not set CONFIG_KSI8560=y +# CONFIG_XES_MPC85xx is not set # CONFIG_STX_GP3 is not set # CONFIG_TQM8540 is not set # CONFIG_TQM8541 is not set @@ -224,6 +239,7 @@ CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=y CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -242,9 +258,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -346,6 +362,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -363,7 +380,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -466,6 +487,7 @@ CONFIG_MTD_PHYSMAP_OF=y # CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -520,7 +542,6 @@ CONFIG_IDE_PROC_FS=y # CONFIG_MD is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -560,6 +581,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set CONFIG_FS_ENET=y # CONFIG_FS_ENET_HAS_SCC is not set CONFIG_FS_ENET_HAS_FCC=y @@ -567,6 +589,7 @@ CONFIG_FS_ENET_MDIO_FCC=y CONFIG_NETDEV_1000=y CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set CONFIG_NETDEV_10000=y # @@ -654,6 +677,11 @@ CONFIG_GEN_RTC=y # CONFIG_TCG_TPM is not set # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y @@ -710,22 +738,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -777,6 +790,10 @@ CONFIG_USB_SUPPORT=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -797,10 +814,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -916,6 +935,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -946,6 +966,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -958,7 +981,6 @@ CONFIG_DEBUG_MUTEXES=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -972,16 +994,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -990,9 +1011,13 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_PPC_EMULATED_STATS is not set # CONFIG_CODE_PATCHING_SELFTEST is not set # CONFIG_FTR_FIXUP_SELFTEST is not set # CONFIG_MSI_BITMAP_SELFTEST is not set diff --git a/arch/powerpc/configs/85xx/mpc8540_ads_defconfig b/arch/powerpc/configs/85xx/mpc8540_ads_defconfig index 7b43be7586b..fb10cc83702 100644 --- a/arch/powerpc/configs/85xx/mpc8540_ads_defconfig +++ b/arch/powerpc/configs/85xx/mpc8540_ads_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:17 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:15 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set CONFIG_PPC_85xx=y # CONFIG_PPC_8xx is not set # CONFIG_40x is not set @@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -56,11 +57,13 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -111,7 +114,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -124,8 +126,15 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -138,6 +147,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -145,7 +158,7 @@ CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -178,6 +191,7 @@ CONFIG_MPC8540_ADS=y # CONFIG_MPC85xx_DS is not set # CONFIG_SOCRATES is not set # CONFIG_KSI8560 is not set +# CONFIG_XES_MPC85xx is not set # CONFIG_STX_GP3 is not set # CONFIG_TQM8540 is not set # CONFIG_TQM8541 is not set @@ -226,6 +240,7 @@ CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=y CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -244,9 +259,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -348,6 +363,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -365,7 +381,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -387,6 +407,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_CONNECTOR is not set # CONFIG_MTD is not set CONFIG_OF_DEVICE=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -423,7 +444,6 @@ CONFIG_HAVE_IDE=y # CONFIG_MD is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -462,9 +482,11 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set CONFIG_NETDEV_1000=y CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set CONFIG_NETDEV_10000=y # @@ -555,6 +577,11 @@ CONFIG_GEN_RTC=y # CONFIG_TCG_TPM is not set # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -590,22 +617,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -657,6 +669,10 @@ CONFIG_USB_SUPPORT=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -676,10 +692,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -794,6 +812,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -824,6 +843,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -835,7 +857,6 @@ CONFIG_DEBUG_MUTEXES=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -849,16 +870,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -866,6 +886,9 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set diff --git a/arch/powerpc/configs/85xx/mpc8560_ads_defconfig b/arch/powerpc/configs/85xx/mpc8560_ads_defconfig index 62adb71a5d4..5c8ce697882 100644 --- a/arch/powerpc/configs/85xx/mpc8560_ads_defconfig +++ b/arch/powerpc/configs/85xx/mpc8560_ads_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:17 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:16 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set CONFIG_PPC_85xx=y # CONFIG_PPC_8xx is not set # CONFIG_40x is not set @@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -57,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -112,7 +115,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -125,9 +127,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -141,6 +150,10 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -148,7 +161,7 @@ CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -181,6 +194,7 @@ CONFIG_MPC8560_ADS=y # CONFIG_MPC85xx_DS is not set # CONFIG_SOCRATES is not set # CONFIG_KSI8560 is not set +# CONFIG_XES_MPC85xx is not set # CONFIG_STX_GP3 is not set # CONFIG_TQM8540 is not set # CONFIG_TQM8541 is not set @@ -229,6 +243,7 @@ CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=y CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -247,9 +262,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -360,6 +375,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -377,7 +393,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -400,6 +420,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_MTD is not set CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -431,6 +452,7 @@ CONFIG_MISC_DEVICES=y # EEPROM support # # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -450,14 +472,17 @@ CONFIG_HAVE_IDE=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -504,6 +529,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_FS_ENET=y # CONFIG_FS_ENET_HAS_SCC is not set @@ -527,8 +553,10 @@ CONFIG_E1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -646,6 +674,11 @@ CONFIG_GEN_RTC=y CONFIG_DEVPORT=y # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y @@ -707,22 +740,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -779,6 +797,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -798,10 +820,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -916,6 +940,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -946,6 +971,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -957,7 +985,6 @@ CONFIG_DEBUG_MUTEXES=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -971,16 +998,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -988,6 +1014,9 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set diff --git a/arch/powerpc/configs/85xx/mpc85xx_cds_defconfig b/arch/powerpc/configs/85xx/mpc85xx_cds_defconfig index 41209e3a654..158e63e8607 100644 --- a/arch/powerpc/configs/85xx/mpc85xx_cds_defconfig +++ b/arch/powerpc/configs/85xx/mpc85xx_cds_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:18 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:17 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set CONFIG_PPC_85xx=y # CONFIG_PPC_8xx is not set # CONFIG_40x is not set @@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -56,11 +57,13 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -111,7 +114,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -124,9 +126,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -139,6 +148,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -146,7 +159,7 @@ CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -179,6 +192,7 @@ CONFIG_MPC85xx_CDS=y # CONFIG_MPC85xx_DS is not set # CONFIG_SOCRATES is not set # CONFIG_KSI8560 is not set +# CONFIG_XES_MPC85xx is not set # CONFIG_STX_GP3 is not set # CONFIG_TQM8540 is not set # CONFIG_TQM8541 is not set @@ -227,6 +241,7 @@ CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=y CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -245,9 +260,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -358,6 +373,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -375,7 +391,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -397,6 +417,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_CONNECTOR is not set # CONFIG_MTD is not set CONFIG_OF_DEVICE=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -428,6 +449,7 @@ CONFIG_MISC_DEVICES=y # EEPROM support # # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y CONFIG_IDE=y @@ -502,14 +524,17 @@ CONFIG_BLK_DEV_IDEDMA=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -556,6 +581,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -575,8 +601,10 @@ CONFIG_E1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -698,6 +726,11 @@ CONFIG_GEN_RTC=y CONFIG_DEVPORT=y # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -737,22 +770,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -809,6 +827,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -828,10 +850,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -946,6 +970,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -976,6 +1001,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -987,7 +1015,6 @@ CONFIG_DEBUG_MUTEXES=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -1001,16 +1028,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -1018,6 +1044,9 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set diff --git a/arch/powerpc/configs/85xx/sbc8548_defconfig b/arch/powerpc/configs/85xx/sbc8548_defconfig index 6c36c9c7abf..2726fca1d69 100644 --- a/arch/powerpc/configs/85xx/sbc8548_defconfig +++ b/arch/powerpc/configs/85xx/sbc8548_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:19 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:18 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set CONFIG_PPC_85xx=y # CONFIG_PPC_8xx is not set # CONFIG_40x is not set @@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -56,11 +57,13 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -110,7 +113,6 @@ CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -123,8 +125,15 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -137,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -144,7 +157,7 @@ CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -177,6 +190,7 @@ CONFIG_MPC85xx=y # CONFIG_MPC85xx_DS is not set # CONFIG_SOCRATES is not set # CONFIG_KSI8560 is not set +# CONFIG_XES_MPC85xx is not set # CONFIG_STX_GP3 is not set # CONFIG_TQM8540 is not set # CONFIG_TQM8541 is not set @@ -224,6 +238,7 @@ CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=y CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -242,9 +257,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -354,6 +369,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -371,7 +387,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -391,6 +411,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_CONNECTOR is not set # CONFIG_MTD is not set CONFIG_OF_DEVICE=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -422,6 +443,7 @@ CONFIG_MISC_DEVICES=y # EEPROM support # # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -441,14 +463,17 @@ CONFIG_HAVE_IDE=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -495,6 +520,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -514,8 +540,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -637,6 +665,11 @@ CONFIG_GEN_RTC=y CONFIG_DEVPORT=y # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -676,22 +709,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -721,6 +739,10 @@ CONFIG_VIDEO_OUTPUT_CONTROL=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -732,10 +754,12 @@ CONFIG_VIDEO_OUTPUT_CONTROL=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -838,6 +862,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -861,22 +886,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_PPC_EARLY_DEBUG is not set diff --git a/arch/powerpc/configs/85xx/sbc8560_defconfig b/arch/powerpc/configs/85xx/sbc8560_defconfig index 4aaf1a6bdc7..b0c469823b0 100644 --- a/arch/powerpc/configs/85xx/sbc8560_defconfig +++ b/arch/powerpc/configs/85xx/sbc8560_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:20 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:19 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set CONFIG_PPC_85xx=y # CONFIG_PPC_8xx is not set # CONFIG_40x is not set @@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -56,11 +57,13 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -111,7 +114,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -124,7 +126,14 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -137,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -144,7 +157,7 @@ CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -177,6 +190,7 @@ CONFIG_MPC85xx=y # CONFIG_MPC85xx_DS is not set # CONFIG_SOCRATES is not set # CONFIG_KSI8560 is not set +# CONFIG_XES_MPC85xx is not set # CONFIG_STX_GP3 is not set # CONFIG_TQM8540 is not set # CONFIG_TQM8541 is not set @@ -224,6 +238,7 @@ CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=y # CONFIG_MATH_EMULATION is not set # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -242,9 +257,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -346,6 +361,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -363,7 +379,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -385,6 +405,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_CONNECTOR is not set # CONFIG_MTD is not set CONFIG_OF_DEVICE=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -421,7 +442,6 @@ CONFIG_HAVE_IDE=y # CONFIG_MD is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -460,9 +480,11 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set CONFIG_NETDEV_1000=y CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set CONFIG_NETDEV_10000=y # @@ -551,6 +573,11 @@ CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_TCG_TPM is not set # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -586,22 +613,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -690,6 +702,10 @@ CONFIG_RTC_DRV_M48T59=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -701,10 +717,12 @@ CONFIG_RTC_DRV_M48T59=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -819,6 +837,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -848,6 +867,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -859,7 +881,6 @@ CONFIG_DEBUG_MUTEXES=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -873,16 +894,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -890,6 +910,9 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set diff --git a/arch/powerpc/configs/85xx/socrates_defconfig b/arch/powerpc/configs/85xx/socrates_defconfig index 79984589db6..04c85dada84 100644 --- a/arch/powerpc/configs/85xx/socrates_defconfig +++ b/arch/powerpc/configs/85xx/socrates_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:21 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:19 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set CONFIG_PPC_85xx=y # CONFIG_PPC_8xx is not set # CONFIG_40x is not set @@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -56,11 +57,13 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -109,7 +112,6 @@ CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y # CONFIG_KALLSYMS is not set -# CONFIG_STRIP_ASM_SYMS is not set # CONFIG_HOTPLUG is not set CONFIG_PRINTK=y CONFIG_BUG=y @@ -122,9 +124,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -137,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -149,7 +162,7 @@ CONFIG_MODULE_FORCE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -182,6 +195,7 @@ CONFIG_MPC85xx=y # CONFIG_MPC85xx_DS is not set CONFIG_SOCRATES=y # CONFIG_KSI8560 is not set +# CONFIG_XES_MPC85xx is not set # CONFIG_STX_GP3 is not set # CONFIG_TQM8540 is not set # CONFIG_TQM8541 is not set @@ -229,6 +243,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -247,9 +262,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -357,6 +372,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -373,6 +389,7 @@ CONFIG_CAN_BCM=y # CAN Device Drivers # # CONFIG_CAN_VCAN is not set +# CONFIG_CAN_DEV is not set # CONFIG_CAN_DEBUG_DEVICES is not set # CONFIG_IRDA is not set # CONFIG_BT is not set @@ -382,7 +399,11 @@ CONFIG_WIRELESS=y # CONFIG_WIRELESS_OLD_REGULATORY is not set # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -499,6 +520,7 @@ CONFIG_MTD_NAND_SOCRATES=y CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y CONFIG_OF_SPI=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -535,7 +557,9 @@ CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_AT25 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -558,10 +582,6 @@ CONFIG_BLK_DEV_SD=y # CONFIG_BLK_DEV_SR is not set # CONFIG_CHR_DEV_SG is not set # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -588,14 +608,17 @@ CONFIG_SCSI_WAIT_SCAN=m # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -643,6 +666,8 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set +# CONFIG_KS8851 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -662,8 +687,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -733,6 +760,7 @@ CONFIG_INPUT_TOUCHSCREEN=y # CONFIG_TOUCHSCREEN_AD7879_I2C is not set # CONFIG_TOUCHSCREEN_AD7879_SPI is not set # CONFIG_TOUCHSCREEN_AD7879 is not set +# CONFIG_TOUCHSCREEN_EETI is not set # CONFIG_TOUCHSCREEN_FUJITSU is not set # CONFIG_TOUCHSCREEN_GUNZE is not set # CONFIG_TOUCHSCREEN_ELO is not set @@ -746,6 +774,7 @@ CONFIG_INPUT_TOUCHSCREEN=y # CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set # CONFIG_TOUCHSCREEN_TOUCHIT213 is not set # CONFIG_TOUCHSCREEN_TSC2007 is not set +# CONFIG_TOUCHSCREEN_W90X900 is not set # CONFIG_INPUT_MISC is not set # @@ -862,7 +891,6 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set @@ -875,12 +903,18 @@ CONFIG_SPI_MASTER=y # SPI Master Controller Drivers # # CONFIG_SPI_BITBANG is not set +# CONFIG_SPI_MPC8xxx is not set # # SPI Protocol Masters # # CONFIG_SPI_SPIDEV is not set # CONFIG_SPI_TLE62X0 is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -938,6 +972,7 @@ CONFIG_SENSORS_LM75=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -973,24 +1008,10 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set +# CONFIG_EZX_PCAP is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1110,7 +1131,7 @@ CONFIG_USB_HID=y # CONFIG_HID_CHERRY is not set # CONFIG_HID_CHICONY is not set # CONFIG_HID_CYPRESS is not set -# CONFIG_DRAGONRISE_FF is not set +# CONFIG_HID_DRAGONRISE is not set # CONFIG_HID_EZKEY is not set # CONFIG_HID_KYE is not set # CONFIG_HID_GYRATION is not set @@ -1124,10 +1145,11 @@ CONFIG_USB_HID=y # CONFIG_HID_SAMSUNG is not set # CONFIG_HID_SONY is not set # CONFIG_HID_SUNPLUS is not set -# CONFIG_GREENASIA_FF is not set +# CONFIG_HID_GREENASIA is not set +# CONFIG_HID_SMARTJOYPLUS is not set # CONFIG_HID_TOPSEED is not set -# CONFIG_THRUSTMASTER_FF is not set -# CONFIG_ZEROPLUS_FF is not set +# CONFIG_HID_THRUSTMASTER is not set +# CONFIG_HID_ZEROPLUS is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -1153,6 +1175,7 @@ CONFIG_USB_MON=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y # CONFIG_USB_EHCI_ROOT_HUB_TT is not set # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1162,9 +1185,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=y -CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PPC_OF_BE=y # CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set +CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PCI=y CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y @@ -1284,6 +1307,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1318,6 +1342,10 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1337,10 +1365,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1449,7 +1479,46 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set -# CONFIG_NLS is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +# CONFIG_NLS_CODEPAGE_437 is not set +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +# CONFIG_NLS_ISO8859_1 is not set +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set # CONFIG_DLM is not set # CONFIG_BINARY_PRINTF is not set @@ -1473,6 +1542,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1498,22 +1568,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_PPC_EARLY_DEBUG is not set diff --git a/arch/powerpc/configs/85xx/stx_gp3_defconfig b/arch/powerpc/configs/85xx/stx_gp3_defconfig index bd1bfcddbd0..e7e81d6769f 100644 --- a/arch/powerpc/configs/85xx/stx_gp3_defconfig +++ b/arch/powerpc/configs/85xx/stx_gp3_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:22 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:20 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set CONFIG_PPC_85xx=y # CONFIG_PPC_8xx is not set # CONFIG_40x is not set @@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -57,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -112,7 +115,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -125,9 +127,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -142,6 +151,10 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -153,7 +166,7 @@ CONFIG_MODULES=y CONFIG_MODVERSIONS=y # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -186,6 +199,7 @@ CONFIG_MPC85xx=y # CONFIG_MPC85xx_DS is not set # CONFIG_SOCRATES is not set # CONFIG_KSI8560 is not set +# CONFIG_XES_MPC85xx is not set CONFIG_STX_GP3=y # CONFIG_TQM8540 is not set # CONFIG_TQM8541 is not set @@ -234,6 +248,7 @@ CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=m CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -252,9 +267,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -425,6 +440,7 @@ CONFIG_IP_NF_FILTER=m # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -442,7 +458,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -466,6 +486,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y CONFIG_OF_I2C=m +CONFIG_OF_MDIO=y CONFIG_PARPORT=m CONFIG_PARPORT_PC=m # CONFIG_PARPORT_PC_FIFO is not set @@ -507,7 +528,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y CONFIG_IDE=y @@ -581,10 +604,6 @@ CONFIG_BLK_DEV_SR=m # CONFIG_BLK_DEV_SR_VENDOR is not set CONFIG_CHR_DEV_SG=m # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# CONFIG_SCSI_MULTI_LUN=y CONFIG_SCSI_CONSTANTS=y # CONFIG_SCSI_LOGGING is not set @@ -602,6 +621,7 @@ CONFIG_SCSI_WAIT_SCAN=m CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_CXGB3_ISCSI is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -610,6 +630,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -631,7 +652,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_INIA100 is not set # CONFIG_SCSI_PPA is not set # CONFIG_SCSI_IMM is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_QLOGIC_1280 is not set @@ -654,14 +674,17 @@ CONFIG_SCSI_LOWLEVEL=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -708,6 +731,7 @@ CONFIG_NET_ETHERNET=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_NET_POCKET is not set # CONFIG_ATL2 is not set # CONFIG_FS_ENET is not set @@ -729,8 +753,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -802,12 +828,13 @@ CONFIG_INPUT_EVDEV=m # CONFIG_INPUT_KEYBOARD=y CONFIG_KEYBOARD_ATKBD=y -# CONFIG_KEYBOARD_SUNKBD is not set # CONFIG_KEYBOARD_LKKBD is not set -# CONFIG_KEYBOARD_XTKBD is not set +# CONFIG_KEYBOARD_GPIO is not set +# CONFIG_KEYBOARD_MATRIX is not set # CONFIG_KEYBOARD_NEWTON is not set # CONFIG_KEYBOARD_STOWAWAY is not set -# CONFIG_KEYBOARD_GPIO is not set +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set CONFIG_INPUT_MOUSE=y CONFIG_MOUSE_PS2=y CONFIG_MOUSE_PS2_ALPS=y @@ -821,6 +848,7 @@ CONFIG_MOUSE_PS2_TRACKPOINT=y # CONFIG_MOUSE_BCM5974 is not set # CONFIG_MOUSE_VSXXXAA is not set # CONFIG_MOUSE_GPIO is not set +# CONFIG_MOUSE_SYNAPTICS_I2C is not set # CONFIG_INPUT_JOYSTICK is not set # CONFIG_INPUT_TABLET is not set # CONFIG_INPUT_TOUCHSCREEN is not set @@ -911,6 +939,7 @@ CONFIG_I2C_ALGOBIT=m # I2C system bus drivers (mostly embedded / system-on-chip) # # CONFIG_I2C_CPM is not set +# CONFIG_I2C_DESIGNWARE is not set # CONFIG_I2C_GPIO is not set # CONFIG_I2C_MPC is not set # CONFIG_I2C_OCORES is not set @@ -941,13 +970,17 @@ CONFIG_I2C_ALGOBIT=m # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y @@ -1027,6 +1060,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -1060,23 +1094,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1143,6 +1163,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1162,10 +1186,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1316,6 +1342,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1346,6 +1373,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -1358,7 +1388,6 @@ CONFIG_SCHED_DEBUG=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -1372,16 +1401,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -1389,6 +1417,9 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set diff --git a/arch/powerpc/configs/85xx/tqm8540_defconfig b/arch/powerpc/configs/85xx/tqm8540_defconfig index 767600145fb..2c407523aad 100644 --- a/arch/powerpc/configs/85xx/tqm8540_defconfig +++ b/arch/powerpc/configs/85xx/tqm8540_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:23 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:21 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set CONFIG_PPC_85xx=y # CONFIG_PPC_8xx is not set # CONFIG_40x is not set @@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -56,11 +57,13 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -109,7 +112,6 @@ CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y # CONFIG_KALLSYMS is not set -# CONFIG_STRIP_ASM_SYMS is not set # CONFIG_HOTPLUG is not set CONFIG_PRINTK=y CONFIG_BUG=y @@ -122,9 +124,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -137,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -144,7 +157,7 @@ CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -177,6 +190,7 @@ CONFIG_MPC85xx=y # CONFIG_MPC85xx_DS is not set # CONFIG_SOCRATES is not set # CONFIG_KSI8560 is not set +# CONFIG_XES_MPC85xx is not set # CONFIG_STX_GP3 is not set CONFIG_TQM8540=y # CONFIG_TQM8541 is not set @@ -225,6 +239,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -243,9 +258,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -353,6 +368,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -370,7 +386,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -471,6 +491,7 @@ CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -505,7 +526,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y CONFIG_IDE=y @@ -580,14 +603,17 @@ CONFIG_BLK_DEV_IDEDMA=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -650,6 +676,7 @@ CONFIG_E100=y # CONFIG_SMSC9420 is not set # CONFIG_SUNDANCE is not set # CONFIG_TLAN is not set +# CONFIG_KS8842 is not set # CONFIG_VIA_RHINE is not set # CONFIG_SC92031 is not set # CONFIG_ATL2 is not set @@ -671,8 +698,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -850,13 +879,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -911,6 +944,7 @@ CONFIG_SENSORS_LM75=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -945,23 +979,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1018,6 +1038,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1037,10 +1061,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1167,6 +1193,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1192,22 +1219,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_PPC_EARLY_DEBUG is not set diff --git a/arch/powerpc/configs/85xx/tqm8541_defconfig b/arch/powerpc/configs/85xx/tqm8541_defconfig index 52fafc006dd..845731dc51c 100644 --- a/arch/powerpc/configs/85xx/tqm8541_defconfig +++ b/arch/powerpc/configs/85xx/tqm8541_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:23 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:22 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set CONFIG_PPC_85xx=y # CONFIG_PPC_8xx is not set # CONFIG_40x is not set @@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -57,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -110,7 +113,6 @@ CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y # CONFIG_KALLSYMS is not set -# CONFIG_STRIP_ASM_SYMS is not set # CONFIG_HOTPLUG is not set CONFIG_PRINTK=y CONFIG_BUG=y @@ -123,9 +125,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -139,6 +148,10 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -146,7 +159,7 @@ CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -179,6 +192,7 @@ CONFIG_MPC85xx=y # CONFIG_MPC85xx_DS is not set # CONFIG_SOCRATES is not set # CONFIG_KSI8560 is not set +# CONFIG_XES_MPC85xx is not set # CONFIG_STX_GP3 is not set # CONFIG_TQM8540 is not set CONFIG_TQM8541=y @@ -228,6 +242,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -246,9 +261,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -356,6 +371,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -373,7 +389,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -475,6 +495,7 @@ CONFIG_MTD_CFI_UTIL=y CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -509,7 +530,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y CONFIG_IDE=y @@ -584,14 +607,17 @@ CONFIG_BLK_DEV_IDEDMA=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -654,6 +680,7 @@ CONFIG_E100=y # CONFIG_SMSC9420 is not set # CONFIG_SUNDANCE is not set # CONFIG_TLAN is not set +# CONFIG_KS8842 is not set # CONFIG_VIA_RHINE is not set # CONFIG_SC92031 is not set # CONFIG_ATL2 is not set @@ -676,8 +703,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -831,6 +860,7 @@ CONFIG_I2C_HELPER_AUTO=y # I2C system bus drivers (mostly embedded / system-on-chip) # # CONFIG_I2C_CPM is not set +# CONFIG_I2C_DESIGNWARE is not set # CONFIG_I2C_GPIO is not set CONFIG_I2C_MPC=y # CONFIG_I2C_OCORES is not set @@ -859,13 +889,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y @@ -944,6 +978,7 @@ CONFIG_SENSORS_LM75=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -979,23 +1014,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1052,6 +1073,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1071,10 +1096,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1201,6 +1228,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1226,22 +1254,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_PPC_EARLY_DEBUG is not set diff --git a/arch/powerpc/configs/85xx/tqm8548_defconfig b/arch/powerpc/configs/85xx/tqm8548_defconfig index 8b4faae7a9a..4f228a90527 100644 --- a/arch/powerpc/configs/85xx/tqm8548_defconfig +++ b/arch/powerpc/configs/85xx/tqm8548_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:24 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:23 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set CONFIG_PPC_85xx=y # CONFIG_PPC_8xx is not set # CONFIG_40x is not set @@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -56,11 +57,13 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -111,7 +114,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -124,9 +126,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -140,6 +149,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -152,7 +165,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -185,6 +198,7 @@ CONFIG_MPC85xx=y # CONFIG_MPC85xx_DS is not set # CONFIG_SOCRATES is not set # CONFIG_KSI8560 is not set +# CONFIG_XES_MPC85xx is not set # CONFIG_STX_GP3 is not set # CONFIG_TQM8540 is not set # CONFIG_TQM8541 is not set @@ -234,6 +248,7 @@ CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=y CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -252,9 +267,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -281,6 +296,8 @@ CONFIG_PCI_DOMAINS=y CONFIG_PCI_SYSCALL=y CONFIG_PCIEPORTBUS=y CONFIG_PCIEAER=y +# CONFIG_PCIE_ECRC is not set +# CONFIG_PCIEAER_INJECT is not set # CONFIG_PCIEASPM is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set @@ -368,6 +385,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -497,6 +515,7 @@ CONFIG_MTD_NAND_FSL_UPM=y # CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -531,7 +550,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -551,14 +572,17 @@ CONFIG_HAVE_IDE=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -605,6 +629,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -624,8 +649,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -801,13 +828,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -862,6 +893,7 @@ CONFIG_SENSORS_LM75=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -896,23 +928,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -977,6 +995,7 @@ CONFIG_RTC_DRV_DS1307=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1004,6 +1023,10 @@ CONFIG_RTC_DRV_DS1307=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1015,10 +1038,12 @@ CONFIG_RTC_DRV_DS1307=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1145,6 +1170,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1175,6 +1201,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -1187,7 +1216,6 @@ CONFIG_DEBUG_MUTEXES=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -1201,16 +1229,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -1218,6 +1245,9 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set diff --git a/arch/powerpc/configs/85xx/tqm8555_defconfig b/arch/powerpc/configs/85xx/tqm8555_defconfig index 170360934ce..9196724bebc 100644 --- a/arch/powerpc/configs/85xx/tqm8555_defconfig +++ b/arch/powerpc/configs/85xx/tqm8555_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:25 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:24 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set CONFIG_PPC_85xx=y # CONFIG_PPC_8xx is not set # CONFIG_40x is not set @@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -57,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -110,7 +113,6 @@ CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y # CONFIG_KALLSYMS is not set -# CONFIG_STRIP_ASM_SYMS is not set # CONFIG_HOTPLUG is not set CONFIG_PRINTK=y CONFIG_BUG=y @@ -123,9 +125,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -139,6 +148,10 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -146,7 +159,7 @@ CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -179,6 +192,7 @@ CONFIG_MPC85xx=y # CONFIG_MPC85xx_DS is not set # CONFIG_SOCRATES is not set # CONFIG_KSI8560 is not set +# CONFIG_XES_MPC85xx is not set # CONFIG_STX_GP3 is not set # CONFIG_TQM8540 is not set # CONFIG_TQM8541 is not set @@ -228,6 +242,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -246,9 +261,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -356,6 +371,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -373,7 +389,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -475,6 +495,7 @@ CONFIG_MTD_CFI_UTIL=y CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -509,7 +530,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y CONFIG_IDE=y @@ -584,14 +607,17 @@ CONFIG_BLK_DEV_IDEDMA=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -654,6 +680,7 @@ CONFIG_E100=y # CONFIG_SMSC9420 is not set # CONFIG_SUNDANCE is not set # CONFIG_TLAN is not set +# CONFIG_KS8842 is not set # CONFIG_VIA_RHINE is not set # CONFIG_SC92031 is not set # CONFIG_ATL2 is not set @@ -676,8 +703,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -831,6 +860,7 @@ CONFIG_I2C_HELPER_AUTO=y # I2C system bus drivers (mostly embedded / system-on-chip) # # CONFIG_I2C_CPM is not set +# CONFIG_I2C_DESIGNWARE is not set # CONFIG_I2C_GPIO is not set CONFIG_I2C_MPC=y # CONFIG_I2C_OCORES is not set @@ -859,13 +889,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y @@ -944,6 +978,7 @@ CONFIG_SENSORS_LM75=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -979,23 +1014,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1052,6 +1073,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1071,10 +1096,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1201,6 +1228,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1226,22 +1254,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_PPC_EARLY_DEBUG is not set diff --git a/arch/powerpc/configs/85xx/tqm8560_defconfig b/arch/powerpc/configs/85xx/tqm8560_defconfig index f41cc2444d4..2e49a6e9faf 100644 --- a/arch/powerpc/configs/85xx/tqm8560_defconfig +++ b/arch/powerpc/configs/85xx/tqm8560_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:26 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:25 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set CONFIG_PPC_85xx=y # CONFIG_PPC_8xx is not set # CONFIG_40x is not set @@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -57,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -110,7 +113,6 @@ CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y # CONFIG_KALLSYMS is not set -# CONFIG_STRIP_ASM_SYMS is not set # CONFIG_HOTPLUG is not set CONFIG_PRINTK=y CONFIG_BUG=y @@ -123,9 +125,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -139,6 +148,10 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -146,7 +159,7 @@ CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -179,6 +192,7 @@ CONFIG_MPC85xx=y # CONFIG_MPC85xx_DS is not set # CONFIG_SOCRATES is not set # CONFIG_KSI8560 is not set +# CONFIG_XES_MPC85xx is not set # CONFIG_STX_GP3 is not set # CONFIG_TQM8540 is not set # CONFIG_TQM8541 is not set @@ -228,6 +242,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -246,9 +261,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -356,6 +371,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -373,7 +389,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -475,6 +495,7 @@ CONFIG_MTD_CFI_UTIL=y CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -509,7 +530,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y CONFIG_IDE=y @@ -584,14 +607,17 @@ CONFIG_BLK_DEV_IDEDMA=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -654,6 +680,7 @@ CONFIG_E100=y # CONFIG_SMSC9420 is not set # CONFIG_SUNDANCE is not set # CONFIG_TLAN is not set +# CONFIG_KS8842 is not set # CONFIG_VIA_RHINE is not set # CONFIG_SC92031 is not set # CONFIG_ATL2 is not set @@ -676,8 +703,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -831,6 +860,7 @@ CONFIG_I2C_HELPER_AUTO=y # I2C system bus drivers (mostly embedded / system-on-chip) # # CONFIG_I2C_CPM is not set +# CONFIG_I2C_DESIGNWARE is not set # CONFIG_I2C_GPIO is not set CONFIG_I2C_MPC=y # CONFIG_I2C_OCORES is not set @@ -859,13 +889,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y @@ -944,6 +978,7 @@ CONFIG_SENSORS_LM75=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -979,23 +1014,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1052,6 +1073,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1071,10 +1096,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1201,6 +1228,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1226,22 +1254,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_PPC_EARLY_DEBUG is not set diff --git a/arch/powerpc/configs/85xx/xes_mpc85xx_defconfig b/arch/powerpc/configs/85xx/xes_mpc85xx_defconfig index 2552cbefba6..1025da2bf06 100644 --- a/arch/powerpc/configs/85xx/xes_mpc85xx_defconfig +++ b/arch/powerpc/configs/85xx/xes_mpc85xx_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc6 -# Thu Jun 11 11:25:17 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:25 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set CONFIG_PPC_85xx=y # CONFIG_PPC_8xx is not set # CONFIG_40x is not set @@ -35,15 +35,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -64,6 +65,7 @@ CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -114,7 +116,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_ALL=y CONFIG_KALLSYMS_EXTRA_PASS=y -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -127,9 +128,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -144,6 +152,10 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_USE_GENERIC_SMP_HELPERS=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -157,7 +169,7 @@ CONFIG_MODVERSIONS=y # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y -CONFIG_LBD=y +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -239,6 +251,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -258,9 +271,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -287,6 +300,8 @@ CONFIG_PCI_DOMAINS=y CONFIG_PCI_SYSCALL=y CONFIG_PCIEPORTBUS=y CONFIG_PCIEAER=y +# CONFIG_PCIE_ECRC is not set +# CONFIG_PCIEAER_INJECT is not set # CONFIG_PCIEASPM is not set CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_PCI_MSI=y @@ -404,6 +419,7 @@ CONFIG_IPV6_NDISC_NODETYPE=y # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -540,6 +556,7 @@ CONFIG_MTD_NAND_FSL_UPM=y CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -575,7 +592,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -599,10 +618,6 @@ CONFIG_BLK_DEV_SR=y # CONFIG_BLK_DEV_SR_VENDOR is not set CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# CONFIG_SCSI_MULTI_LUN=y # CONFIG_SCSI_CONSTANTS is not set CONFIG_SCSI_LOGGING=y @@ -619,6 +634,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -627,6 +643,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -646,7 +663,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -730,14 +746,17 @@ CONFIG_PATA_ALI=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_DUMMY=y # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -784,6 +803,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -803,8 +823,10 @@ CONFIG_E1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -986,13 +1008,17 @@ CONFIG_I2C_MPC=y # CONFIG_DS1682 is not set # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y @@ -1072,6 +1098,7 @@ CONFIG_SENSORS_LM90=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -1126,23 +1153,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -# CONFIG_DAB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1187,7 +1200,7 @@ CONFIG_USB_HID=y # CONFIG_HID_CHERRY is not set # CONFIG_HID_CHICONY is not set # CONFIG_HID_CYPRESS is not set -# CONFIG_DRAGONRISE_FF is not set +# CONFIG_HID_DRAGONRISE is not set # CONFIG_HID_EZKEY is not set # CONFIG_HID_KYE is not set # CONFIG_HID_GYRATION is not set @@ -1201,10 +1214,11 @@ CONFIG_USB_HID=y # CONFIG_HID_SAMSUNG is not set # CONFIG_HID_SONY is not set # CONFIG_HID_SUNPLUS is not set -# CONFIG_GREENASIA_FF is not set +# CONFIG_HID_GREENASIA is not set +# CONFIG_HID_SMARTJOYPLUS is not set # CONFIG_HID_TOPSEED is not set -# CONFIG_THRUSTMASTER_FF is not set -# CONFIG_ZEROPLUS_FF is not set +# CONFIG_HID_THRUSTMASTER is not set +# CONFIG_HID_ZEROPLUS is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -1230,6 +1244,7 @@ CONFIG_USB_MON=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set # CONFIG_USB_EHCI_HCD is not set # CONFIG_USB_OXU210HP_HCD is not set # CONFIG_USB_ISP116X_HCD is not set @@ -1325,7 +1340,7 @@ CONFIG_LEDS_CLASS=y CONFIG_LEDS_GPIO=y CONFIG_LEDS_GPIO_PLATFORM=y CONFIG_LEDS_GPIO_OF=y -# CONFIG_LEDS_LP5521 is not set +# CONFIG_LEDS_LP3944 is not set CONFIG_LEDS_PCA955X=y # CONFIG_LEDS_BD2802 is not set @@ -1352,8 +1367,6 @@ CONFIG_EDAC=y # CONFIG_EDAC_DEBUG is not set CONFIG_EDAC_MM_EDAC=y CONFIG_EDAC_MPC85XX=y -# CONFIG_EDAC_AMD8131 is not set -# CONFIG_EDAC_AMD8111 is not set CONFIG_RTC_LIB=y CONFIG_RTC_CLASS=y CONFIG_RTC_HCTOSYS=y @@ -1385,6 +1398,7 @@ CONFIG_RTC_DRV_DS1307=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1425,6 +1439,10 @@ CONFIG_NET_DMA=y # CONFIG_DMATEST is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1444,11 +1462,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1629,6 +1648,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1659,6 +1679,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -1671,7 +1694,6 @@ CONFIG_SCHED_DEBUG=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -1685,16 +1707,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -1702,6 +1723,9 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set diff --git a/arch/powerpc/configs/86xx/gef_ppc9a_defconfig b/arch/powerpc/configs/86xx/gef_ppc9a_defconfig index d8354d993b2..527ad1a5e80 100644 --- a/arch/powerpc/configs/86xx/gef_ppc9a_defconfig +++ b/arch/powerpc/configs/86xx/gef_ppc9a_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30 -# Thu Jul 2 13:55:24 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:31 2009 # # CONFIG_PPC64 is not set @@ -39,6 +39,7 @@ CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_GENERIC_LOCKBREAK=y @@ -1322,6 +1323,8 @@ CONFIG_USB_EHCI_HCD=y # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=y +# CONFIG_USB_OHCI_HCD_PPC_OF_BE is not set +# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set # CONFIG_USB_OHCI_HCD_PPC_OF is not set # CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set # CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set diff --git a/arch/powerpc/configs/86xx/gef_sbc310_defconfig b/arch/powerpc/configs/86xx/gef_sbc310_defconfig index f2362e5bf06..cd338d493be 100644 --- a/arch/powerpc/configs/86xx/gef_sbc310_defconfig +++ b/arch/powerpc/configs/86xx/gef_sbc310_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30 -# Thu Jul 2 14:10:12 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:29 2009 # # CONFIG_PPC64 is not set @@ -39,6 +39,7 @@ CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_GENERIC_LOCKBREAK=y @@ -1267,6 +1268,8 @@ CONFIG_USB_EHCI_HCD=y # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=y +# CONFIG_USB_OHCI_HCD_PPC_OF_BE is not set +# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set # CONFIG_USB_OHCI_HCD_PPC_OF is not set # CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set # CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set diff --git a/arch/powerpc/configs/86xx/gef_sbc610_defconfig b/arch/powerpc/configs/86xx/gef_sbc610_defconfig index c6a7fc82b69..ba47883f4aa 100644 --- a/arch/powerpc/configs/86xx/gef_sbc610_defconfig +++ b/arch/powerpc/configs/86xx/gef_sbc610_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:30 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:30 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_PHYS_64BIT is not set CONFIG_ALTIVEC=y CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y CONFIG_SMP=y CONFIG_NR_CPUS=2 CONFIG_PPC32=y @@ -32,16 +34,17 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_GENERIC_LOCKBREAK=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -56,11 +59,13 @@ CONFIG_PPC_UDBG_16550=y CONFIG_GENERIC_TBSYNC=y CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -114,7 +119,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -127,8 +131,15 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -143,6 +154,10 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_USE_GENERIC_SMP_HELPERS=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -156,7 +171,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -235,6 +250,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=m # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -256,9 +272,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -285,6 +301,8 @@ CONFIG_PCI_DOMAINS=y CONFIG_PCI_SYSCALL=y CONFIG_PCIEPORTBUS=y CONFIG_PCIEAER=y +# CONFIG_PCIE_ECRC is not set +# CONFIG_PCIEAER_INJECT is not set # CONFIG_PCIEASPM is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set @@ -510,6 +528,7 @@ CONFIG_LLC=m # CONFIG_ECONET is not set CONFIG_WAN_ROUTER=m # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set CONFIG_NET_SCHED=y # @@ -566,7 +585,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -678,6 +701,7 @@ CONFIG_MTD_PHYSMAP_OF=y CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -713,7 +737,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -737,10 +763,6 @@ CONFIG_BLK_DEV_SR=y # CONFIG_BLK_DEV_SR_VENDOR is not set # CONFIG_CHR_DEV_SG is not set # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -757,6 +779,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -765,6 +788,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -784,7 +808,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -868,14 +891,17 @@ CONFIG_SATA_SIL=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_DUMMY=m CONFIG_BONDING=m # CONFIG_MACVLAN is not set @@ -922,6 +948,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -941,8 +968,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -1149,13 +1178,17 @@ CONFIG_DS1682=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y @@ -1235,6 +1268,7 @@ CONFIG_SENSORS_LM92=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -1290,24 +1324,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1352,7 +1371,7 @@ CONFIG_HID_BELKIN=y CONFIG_HID_CHERRY=y CONFIG_HID_CHICONY=y CONFIG_HID_CYPRESS=y -# CONFIG_DRAGONRISE_FF is not set +# CONFIG_HID_DRAGONRISE is not set CONFIG_HID_EZKEY=y # CONFIG_HID_KYE is not set CONFIG_HID_GYRATION=y @@ -1369,10 +1388,11 @@ CONFIG_HID_PETALYNX=y CONFIG_HID_SAMSUNG=y CONFIG_HID_SONY=y CONFIG_HID_SUNPLUS=y -# CONFIG_GREENASIA_FF is not set +# CONFIG_HID_GREENASIA is not set +# CONFIG_HID_SMARTJOYPLUS is not set # CONFIG_HID_TOPSEED is not set -CONFIG_THRUSTMASTER_FF=m -CONFIG_ZEROPLUS_FF=m +# CONFIG_HID_THRUSTMASTER is not set +# CONFIG_HID_ZEROPLUS is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -1398,6 +1418,7 @@ CONFIG_USB=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y # CONFIG_USB_EHCI_ROOT_HUB_TT is not set # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1407,6 +1428,8 @@ CONFIG_USB_EHCI_HCD=y # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=y +# CONFIG_USB_OHCI_HCD_PPC_OF_BE is not set +# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set # CONFIG_USB_OHCI_HCD_PPC_OF is not set # CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set # CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set @@ -1527,6 +1550,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set CONFIG_RTC_DRV_RX8581=y +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1554,6 +1578,10 @@ CONFIG_RTC_DRV_RX8581=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1575,10 +1603,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1645,6 +1675,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1734,6 +1765,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1759,10 +1791,14 @@ CONFIG_SCHED_DEBUG=y # CONFIG_TIMER_STATS is not set # CONFIG_DEBUG_OBJECTS is not set # CONFIG_DEBUG_SLAB is not set +CONFIG_DEBUG_PREEMPT=y # CONFIG_DEBUG_RT_MUTEXES is not set # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -1774,7 +1810,6 @@ CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -1788,17 +1823,16 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_PREEMPT_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -1806,6 +1840,9 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set @@ -1829,7 +1866,6 @@ CONFIG_SECURITY_NETWORK=y # CONFIG_SECURITY_PATH is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set # CONFIG_SECURITY_ROOTPLUG is not set -CONFIG_SECURITY_DEFAULT_MMAP_MIN_ADDR=0 # CONFIG_SECURITY_TOMOYO is not set CONFIG_CRYPTO=y diff --git a/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig b/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig index cfd2efcc6bc..a61f183f718 100644 --- a/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig +++ b/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:28 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:27 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_PHYS_64BIT is not set CONFIG_ALTIVEC=y CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -53,11 +56,13 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -109,7 +114,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set CONFIG_KALLSYMS_EXTRA_PASS=y -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -122,9 +126,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -138,6 +149,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -150,7 +165,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -230,6 +245,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -250,9 +266,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -279,6 +295,8 @@ CONFIG_PCI_DOMAINS=y CONFIG_PCI_SYSCALL=y CONFIG_PCIEPORTBUS=y CONFIG_PCIEAER=y +# CONFIG_PCIE_ECRC is not set +# CONFIG_PCIEAER_INJECT is not set # CONFIG_PCIEASPM is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set @@ -381,6 +399,7 @@ CONFIG_IPV6_NDISC_NODETYPE=y # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -398,7 +417,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -549,7 +572,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y CONFIG_IDE=y @@ -620,10 +645,6 @@ CONFIG_BLK_DEV_SD=y # CONFIG_BLK_DEV_SR is not set CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -640,6 +661,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -648,6 +670,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -667,7 +690,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -751,14 +773,17 @@ CONFIG_PATA_ALI=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_DUMMY=y # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -792,6 +817,7 @@ CONFIG_ULI526X=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -959,13 +985,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -993,23 +1023,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1106,6 +1122,11 @@ CONFIG_SND_PCM_OSS_PLUGINS=y CONFIG_SND_VERBOSE_PROCFS=y # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set +# CONFIG_SND_RAWMIDI_SEQ is not set +# CONFIG_SND_OPL3_LIB_SEQ is not set +# CONFIG_SND_OPL4_LIB_SEQ is not set +# CONFIG_SND_SBAWE_SEQ is not set +# CONFIG_SND_EMU10K1_SEQ is not set CONFIG_SND_DRIVERS=y # CONFIG_SND_DUMMY is not set # CONFIG_SND_MTPAV is not set @@ -1130,6 +1151,7 @@ CONFIG_SND_PCI=y # CONFIG_SND_CS4281 is not set # CONFIG_SND_CS46XX is not set # CONFIG_SND_CS5530 is not set +# CONFIG_SND_CTXFI is not set # CONFIG_SND_DARLA20 is not set # CONFIG_SND_GINA20 is not set # CONFIG_SND_LAYLA20 is not set @@ -1160,6 +1182,7 @@ CONFIG_SND_PCI=y # CONFIG_SND_INTEL8X0 is not set # CONFIG_SND_INTEL8X0M is not set # CONFIG_SND_KORG1212 is not set +# CONFIG_SND_LX6464ES is not set # CONFIG_SND_MAESTRO3 is not set # CONFIG_SND_MIXART is not set # CONFIG_SND_NM256 is not set @@ -1251,6 +1274,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1278,6 +1302,10 @@ CONFIG_RTC_DRV_CMOS=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1297,12 +1325,15 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y # CONFIG_DNOTIFY is not set # CONFIG_INOTIFY is not set +CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set @@ -1464,6 +1495,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1494,6 +1526,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -1506,7 +1541,6 @@ CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -1520,16 +1554,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -1537,6 +1570,9 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set diff --git a/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig b/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig index 0bee3e30394..7016ce73260 100644 --- a/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig +++ b/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:28 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:28 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_PHYS_64BIT is not set CONFIG_ALTIVEC=y CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y CONFIG_SMP=y CONFIG_NR_CPUS=2 CONFIG_PPC32=y @@ -32,15 +34,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -54,11 +57,13 @@ CONFIG_PPC_UDBG_16550=y CONFIG_GENERIC_TBSYNC=y CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -113,7 +118,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_ALL=y CONFIG_KALLSYMS_EXTRA_PASS=y -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -126,9 +130,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -143,6 +154,10 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_USE_GENERIC_SMP_HELPERS=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -156,7 +171,7 @@ CONFIG_MODVERSIONS=y # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y -CONFIG_LBD=y +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -234,7 +249,9 @@ CONFIG_BINFMT_ELF=y # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set # CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=m -# CONFIG_IOMMU_HELPER is not set +CONFIG_IOMMU_HELPER=y +CONFIG_SWIOTLB=y +CONFIG_PPC_NEED_DMA_SYNC_OPS=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -256,9 +273,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -401,6 +418,7 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -419,7 +437,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -444,6 +466,7 @@ CONFIG_EXTRA_FIRMWARE="" # CONFIG_MTD is not set CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -479,7 +502,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set CONFIG_EEPROM_LEGACY=y +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -503,10 +528,6 @@ CONFIG_BLK_DEV_SR=y # CONFIG_BLK_DEV_SR_VENDOR is not set CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# CONFIG_SCSI_MULTI_LUN=y # CONFIG_SCSI_CONSTANTS is not set CONFIG_SCSI_LOGGING=y @@ -524,6 +545,7 @@ CONFIG_SCSI_WAIT_SCAN=m CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_CXGB3_ISCSI is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -532,6 +554,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -551,7 +574,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -635,14 +657,17 @@ CONFIG_PATA_ALI=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_DUMMY=y # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -689,6 +714,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -708,8 +734,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -909,13 +937,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -943,76 +975,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -CONFIG_DVB_CORE=m -CONFIG_VIDEO_MEDIA=m - -# -# Multimedia drivers -# -# CONFIG_MEDIA_ATTACH is not set -CONFIG_MEDIA_TUNER=m -# CONFIG_MEDIA_TUNER_CUSTOMISE is not set -CONFIG_MEDIA_TUNER_SIMPLE=m -CONFIG_MEDIA_TUNER_TDA8290=m -CONFIG_MEDIA_TUNER_TDA9887=m -CONFIG_MEDIA_TUNER_TEA5761=m -CONFIG_MEDIA_TUNER_TEA5767=m -CONFIG_MEDIA_TUNER_MT20XX=m -CONFIG_MEDIA_TUNER_XC2028=m -CONFIG_MEDIA_TUNER_XC5000=m -CONFIG_MEDIA_TUNER_MC44S803=m -# CONFIG_DVB_DYNAMIC_MINORS is not set -CONFIG_DVB_CAPTURE_DRIVERS=y - -# -# Supported SAA7146 based PCI Adapters -# -# CONFIG_TTPCI_EEPROM is not set -# CONFIG_DVB_BUDGET_CORE is not set - -# -# Supported USB Adapters -# -# CONFIG_DVB_USB is not set -# CONFIG_DVB_TTUSB_BUDGET is not set -# CONFIG_DVB_TTUSB_DEC is not set -# CONFIG_DVB_SIANO_SMS1XXX is not set - -# -# Supported FlexCopII (B2C2) Adapters -# -# CONFIG_DVB_B2C2_FLEXCOP is not set - -# -# Supported BT878 Adapters -# - -# -# Supported Pluto2 Adapters -# -# CONFIG_DVB_PLUTO2 is not set - -# -# Supported SDMC DM1105 Adapters -# -# CONFIG_DVB_DM1105 is not set - -# -# Supported DVB Frontends -# -# CONFIG_DVB_FE_CUSTOMISE is not set -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1052,6 +1017,11 @@ CONFIG_SND_VERBOSE_PROCFS=y # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set CONFIG_SND_VMASTER=y +# CONFIG_SND_RAWMIDI_SEQ is not set +# CONFIG_SND_OPL3_LIB_SEQ is not set +# CONFIG_SND_OPL4_LIB_SEQ is not set +# CONFIG_SND_SBAWE_SEQ is not set +# CONFIG_SND_EMU10K1_SEQ is not set CONFIG_SND_AC97_CODEC=y CONFIG_SND_DRIVERS=y # CONFIG_SND_DUMMY is not set @@ -1078,6 +1048,7 @@ CONFIG_SND_PCI=y # CONFIG_SND_CS4281 is not set # CONFIG_SND_CS46XX is not set # CONFIG_SND_CS5530 is not set +# CONFIG_SND_CTXFI is not set # CONFIG_SND_DARLA20 is not set # CONFIG_SND_GINA20 is not set # CONFIG_SND_LAYLA20 is not set @@ -1108,6 +1079,7 @@ CONFIG_SND_PCI=y CONFIG_SND_INTEL8X0=y # CONFIG_SND_INTEL8X0M is not set # CONFIG_SND_KORG1212 is not set +# CONFIG_SND_LX6464ES is not set # CONFIG_SND_MAESTRO3 is not set # CONFIG_SND_MIXART is not set # CONFIG_SND_NM256 is not set @@ -1152,7 +1124,7 @@ CONFIG_HID_BELKIN=y CONFIG_HID_CHERRY=y CONFIG_HID_CHICONY=y CONFIG_HID_CYPRESS=y -# CONFIG_DRAGONRISE_FF is not set +# CONFIG_HID_DRAGONRISE is not set CONFIG_HID_EZKEY=y # CONFIG_HID_KYE is not set CONFIG_HID_GYRATION=y @@ -1169,10 +1141,11 @@ CONFIG_HID_PETALYNX=y CONFIG_HID_SAMSUNG=y CONFIG_HID_SONY=y CONFIG_HID_SUNPLUS=y -# CONFIG_GREENASIA_FF is not set +# CONFIG_HID_GREENASIA is not set +# CONFIG_HID_SMARTJOYPLUS is not set # CONFIG_HID_TOPSEED is not set -CONFIG_THRUSTMASTER_FF=m -CONFIG_ZEROPLUS_FF=m +# CONFIG_HID_THRUSTMASTER is not set +# CONFIG_HID_ZEROPLUS is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -1198,6 +1171,7 @@ CONFIG_USB_MON=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y # CONFIG_USB_EHCI_ROOT_HUB_TT is not set # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1207,9 +1181,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=y -CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PPC_OF_BE=y CONFIG_USB_OHCI_HCD_PPC_OF_LE=y +CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PCI=y CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y @@ -1329,6 +1303,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1356,6 +1331,10 @@ CONFIG_RTC_DRV_CMOS=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1375,11 +1354,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1454,6 +1434,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y CONFIG_NFSD=y # CONFIG_NFSD_V3 is not set @@ -1555,6 +1536,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1585,6 +1567,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -1597,7 +1582,6 @@ CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -1611,16 +1595,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -1628,6 +1611,9 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set diff --git a/arch/powerpc/configs/86xx/sbc8641d_defconfig b/arch/powerpc/configs/86xx/sbc8641d_defconfig index c30a0c71587..f5ca2e0cd40 100644 --- a/arch/powerpc/configs/86xx/sbc8641d_defconfig +++ b/arch/powerpc/configs/86xx/sbc8641d_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:27 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:26 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_PHYS_64BIT is not set CONFIG_ALTIVEC=y CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y CONFIG_SMP=y CONFIG_NR_CPUS=2 CONFIG_PPC32=y @@ -32,16 +34,17 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_GENERIC_LOCKBREAK=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -55,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y CONFIG_GENERIC_TBSYNC=y CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -113,7 +118,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -126,8 +130,15 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -142,6 +153,11 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_USE_GENERIC_SMP_HELPERS=y + +# +# GCOV-based kernel profiling +# +# CONFIG_GCOV_KERNEL is not set # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -155,7 +171,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -234,6 +250,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=m # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -255,9 +272,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -284,6 +301,8 @@ CONFIG_PCI_DOMAINS=y CONFIG_PCI_SYSCALL=y CONFIG_PCIEPORTBUS=y CONFIG_PCIEAER=y +# CONFIG_PCIE_ECRC is not set +# CONFIG_PCIEAER_INJECT is not set # CONFIG_PCIEASPM is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set @@ -508,6 +527,7 @@ CONFIG_LLC=m # CONFIG_ECONET is not set CONFIG_WAN_ROUTER=m # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set CONFIG_NET_SCHED=y # @@ -564,7 +584,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -675,6 +699,7 @@ CONFIG_MTD_PHYSMAP_OF=y # CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -709,7 +734,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -736,6 +763,7 @@ CONFIG_BLK_DEV_DM=y CONFIG_DM_CRYPT=y CONFIG_DM_SNAPSHOT=y CONFIG_DM_MIRROR=y +# CONFIG_DM_LOG_USERSPACE is not set CONFIG_DM_ZERO=y # CONFIG_DM_MULTIPATH is not set # CONFIG_DM_DELAY is not set @@ -747,14 +775,17 @@ CONFIG_DM_ZERO=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_DUMMY=m CONFIG_BONDING=m # CONFIG_MACVLAN is not set @@ -801,6 +832,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -820,8 +852,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -1018,13 +1052,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -1079,6 +1117,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -1127,23 +1166,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1207,6 +1232,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1236,8 +1265,8 @@ CONFIG_REISERFS_FS_POSIX_ACL=y # CONFIG_REISERFS_FS_SECURITY is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set CONFIG_OCFS2_FS=m CONFIG_OCFS2_FS_O2CB=m CONFIG_OCFS2_FS_STATS=y @@ -1245,6 +1274,8 @@ CONFIG_OCFS2_DEBUG_MASKLOG=y # CONFIG_OCFS2_DEBUG_FS is not set # CONFIG_OCFS2_FS_POSIX_ACL is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1318,6 +1349,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1409,6 +1441,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1434,10 +1467,14 @@ CONFIG_SCHED_DEBUG=y # CONFIG_TIMER_STATS is not set # CONFIG_DEBUG_OBJECTS is not set # CONFIG_DEBUG_SLAB is not set +CONFIG_DEBUG_PREEMPT=y # CONFIG_DEBUG_RT_MUTEXES is not set # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -1449,7 +1486,6 @@ CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -1463,17 +1499,16 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_PREEMPT_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -1482,9 +1517,13 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_PPC_EMULATED_STATS is not set # CONFIG_CODE_PATCHING_SELFTEST is not set # CONFIG_FTR_FIXUP_SELFTEST is not set # CONFIG_MSI_BITMAP_SELFTEST is not set @@ -1505,7 +1544,6 @@ CONFIG_SECURITY_NETWORK=y # CONFIG_SECURITY_NETWORK_XFRM is not set # CONFIG_SECURITY_PATH is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set -CONFIG_SECURITY_DEFAULT_MMAP_MIN_ADDR=0 # CONFIG_SECURITY_TOMOYO is not set CONFIG_CRYPTO=y diff --git a/arch/powerpc/configs/adder875_defconfig b/arch/powerpc/configs/adder875_defconfig index 74f7f7c6fdc..aece6bb5f73 100644 --- a/arch/powerpc/configs/adder875_defconfig +++ b/arch/powerpc/configs/adder875_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:21:50 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:31:47 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set # CONFIG_PPC_85xx is not set CONFIG_PPC_8xx=y # CONFIG_40x is not set @@ -27,15 +27,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -49,12 +50,14 @@ CONFIG_OF=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y # CONFIG_DEFAULT_UIMAGE is not set CONFIG_REDBOOT=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -101,7 +104,6 @@ CONFIG_EMBEDDED=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -114,8 +116,15 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set # CONFIG_VM_EVENT_COUNTERS is not set CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -129,13 +138,18 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# +# CONFIG_GCOV_KERNEL is not set # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_BASE_SMALL=1 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -220,6 +234,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_MATH_EMULATION is not set # CONFIG_8XX_MINIMAL_FPEMU is not set # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_PPC_NEED_DMA_SYNC_OPS=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y @@ -239,9 +254,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -280,6 +295,7 @@ CONFIG_PAGE_OFFSET=0xc0000000 CONFIG_KERNEL_START=0xc0000000 CONFIG_PHYSICAL_START=0x00000000 CONFIG_TASK_SIZE=0x80000000 +CONFIG_CONSISTENT_SIZE=0x00200000 CONFIG_NET=y # @@ -336,6 +352,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -353,7 +370,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -452,6 +473,7 @@ CONFIG_MTD_PHYSMAP_OF=y # # CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set # CONFIG_BLK_DEV is not set # CONFIG_MISC_DEVICES is not set @@ -469,7 +491,6 @@ CONFIG_HAVE_IDE=y # CONFIG_MD is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -508,6 +529,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set CONFIG_FS_ENET=y # CONFIG_FS_ENET_HAS_SCC is not set CONFIG_FS_ENET_HAS_FEC=y @@ -556,11 +578,11 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_KEYBOARD=y CONFIG_KEYBOARD_ATKBD=y -# CONFIG_KEYBOARD_SUNKBD is not set # CONFIG_KEYBOARD_LKKBD is not set -# CONFIG_KEYBOARD_XTKBD is not set # CONFIG_KEYBOARD_NEWTON is not set # CONFIG_KEYBOARD_STOWAWAY is not set +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set CONFIG_INPUT_MOUSE=y CONFIG_MOUSE_PS2=y CONFIG_MOUSE_PS2_ALPS=y @@ -622,6 +644,11 @@ CONFIG_GEN_RTC=y # CONFIG_TCG_TPM is not set # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -644,22 +671,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -685,6 +697,10 @@ CONFIG_VIDEO_OUTPUT_CONTROL=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -696,12 +712,15 @@ CONFIG_VIDEO_OUTPUT_CONTROL=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y # CONFIG_DNOTIFY is not set # CONFIG_INOTIFY is not set +CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set @@ -818,6 +837,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -846,6 +866,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_SLUB_STATS is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -857,7 +880,6 @@ CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -870,16 +892,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -888,9 +909,13 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_PPC_EMULATED_STATS is not set # CONFIG_CODE_PATCHING_SELFTEST is not set # CONFIG_FTR_FIXUP_SELFTEST is not set # CONFIG_MSI_BITMAP_SELFTEST is not set diff --git a/arch/powerpc/configs/c2k_defconfig b/arch/powerpc/configs/c2k_defconfig index 9ffa8de9280..8105360d53f 100644 --- a/arch/powerpc/configs/c2k_defconfig +++ b/arch/powerpc/configs/c2k_defconfig @@ -1,25 +1,27 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:21:51 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:31:48 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_NOT_COHERENT_CACHE=y CONFIG_CHECK_CACHE_COHERENCY=y @@ -32,15 +34,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -54,11 +57,13 @@ CONFIG_OF=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y # CONFIG_DEFAULT_UIMAGE is not set # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -118,7 +123,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set CONFIG_KALLSYMS_EXTRA_PASS=y -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -131,16 +135,23 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y # CONFIG_SLOB is not set CONFIG_PROFILING=y CONFIG_TRACEPOINTS=y -# CONFIG_MARKERS is not set +CONFIG_MARKERS=y CONFIG_OPROFILE=m CONFIG_HAVE_OPROFILE=y CONFIG_KPROBES=y @@ -150,6 +161,11 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# +# CONFIG_GCOV_KERNEL is not set # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -162,7 +178,7 @@ CONFIG_MODULE_UNLOAD=y CONFIG_MODVERSIONS=y # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -CONFIG_LBD=y +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -258,6 +274,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_PPC_NEED_DMA_SYNC_OPS=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y @@ -279,9 +296,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -331,6 +348,7 @@ CONFIG_PAGE_OFFSET=0xc0000000 CONFIG_KERNEL_START=0xc0000000 CONFIG_PHYSICAL_START=0x00000000 CONFIG_TASK_SIZE=0xc0000000 +CONFIG_CONSISTENT_SIZE=0x00200000 CONFIG_NET=y # @@ -583,6 +601,7 @@ CONFIG_LLC=m # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set CONFIG_NET_SCHED=y # @@ -663,7 +682,11 @@ CONFIG_WIRELESS_OLD_REGULATORY=y CONFIG_WIRELESS_EXT=y CONFIG_WIRELESS_EXT_SYSFS=y # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -772,6 +795,7 @@ CONFIG_MTD_PHYSMAP_OF=y # CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y CONFIG_OF_I2C=m +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -816,10 +840,6 @@ CONFIG_BLK_DEV_SR=m CONFIG_BLK_DEV_SR_VENDOR=y CONFIG_CHR_DEV_SG=m # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set CONFIG_SCSI_CONSTANTS=y CONFIG_SCSI_LOGGING=y @@ -836,6 +856,7 @@ CONFIG_SCSI_ISCSI_ATTRS=m CONFIG_SCSI_SRP_ATTRS=m CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_BNX2_ISCSI is not set CONFIG_BLK_DEV_3W_XXXX_RAID=m CONFIG_SCSI_3W_9XXX=m CONFIG_SCSI_ACARD=m @@ -854,6 +875,7 @@ CONFIG_AIC79XX_RESET_DELAY_MS=15000 CONFIG_AIC79XX_DEBUG_MASK=0 # CONFIG_AIC79XX_REG_PRETTY_PRINT is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set CONFIG_SCSI_ARCMSR=m @@ -875,7 +897,6 @@ CONFIG_SCSI_GDTH=m CONFIG_SCSI_IPS=m CONFIG_SCSI_INITIO=m # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set CONFIG_SCSI_SYM53C8XX_2=m CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1 @@ -903,14 +924,17 @@ CONFIG_SCSI_LPFC=m # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_DUMMY=m CONFIG_BONDING=m # CONFIG_MACVLAN is not set @@ -957,6 +981,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -976,6 +1001,7 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_MV643XX_ETH=y # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set @@ -1177,13 +1203,17 @@ CONFIG_I2C_MV64XXX=m CONFIG_SENSORS_PCF8574=m # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -1238,6 +1268,7 @@ CONFIG_SENSORS_SMSC47M1=m CONFIG_SENSORS_SMSC47B397=m # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set CONFIG_SENSORS_VIA686A=m # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -1266,7 +1297,6 @@ CONFIG_SOFT_WATCHDOG=m # CONFIG_PCIPCWATCHDOG=m CONFIG_WDTPCI=m -CONFIG_WDT_501_PCI=y # # USB-based Watchdog Cards @@ -1289,23 +1319,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -# CONFIG_DAB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1354,6 +1370,7 @@ CONFIG_USB_MON=m # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=m CONFIG_USB_EHCI_ROOT_HUB_TT=y # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1362,9 +1379,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=m -CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PPC_OF_BE=y # CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set +CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PCI=y CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y @@ -1545,6 +1562,10 @@ CONFIG_DMADEVICES=y # # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1563,11 +1584,12 @@ CONFIG_FS_MBCACHE=m # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1652,6 +1674,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1764,6 +1787,7 @@ CONFIG_HAS_DMA=y CONFIG_CHECK_SIGNATURE=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1794,6 +1818,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_RT_MUTEX_TESTER is not set CONFIG_DEBUG_SPINLOCK=y # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set CONFIG_DEBUG_SPINLOCK_SLEEP=y # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set CONFIG_STACKTRACE=y @@ -1807,7 +1834,6 @@ CONFIG_DEBUG_MEMORY_INIT=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_KPROBES_SANITY_TEST is not set @@ -1824,30 +1850,34 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_RING_BUFFER=y +CONFIG_EVENT_TRACING=y +CONFIG_CONTEXT_SWITCH_TRACER=y CONFIG_TRACING=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set # CONFIG_BLK_DEV_IO_TRACE is not set -# CONFIG_FTRACE_STARTUP_TEST is not set +# CONFIG_RING_BUFFER_BENCHMARK is not set # CONFIG_DYNAMIC_DEBUG is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 CONFIG_DEBUG_STACKOVERFLOW=y CONFIG_DEBUG_STACK_USAGE=y +# CONFIG_PPC_EMULATED_STATS is not set # CONFIG_CODE_PATCHING_SELFTEST is not set # CONFIG_FTR_FIXUP_SELFTEST is not set # CONFIG_MSI_BITMAP_SELFTEST is not set @@ -1869,7 +1899,6 @@ CONFIG_SECURITY_NETWORK=y # CONFIG_SECURITY_NETWORK_XFRM is not set # CONFIG_SECURITY_PATH is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set -CONFIG_SECURITY_DEFAULT_MMAP_MIN_ADDR=0 CONFIG_SECURITY_SELINUX=y CONFIG_SECURITY_SELINUX_BOOTPARAM=y CONFIG_SECURITY_SELINUX_BOOTPARAM_VALUE=1 diff --git a/arch/powerpc/configs/ep8248e_defconfig b/arch/powerpc/configs/ep8248e_defconfig index 04915c3a43f..0aa5b43ffeb 100644 --- a/arch/powerpc/configs/ep8248e_defconfig +++ b/arch/powerpc/configs/ep8248e_defconfig @@ -1,25 +1,27 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:21:52 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:31:49 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -30,15 +32,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -53,11 +56,13 @@ CONFIG_OF=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y # CONFIG_DEFAULT_UIMAGE is not set # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -99,7 +104,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_ALL=y # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -112,8 +116,15 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -127,6 +138,10 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -134,7 +149,7 @@ CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_INTEGRITY is not set # @@ -213,6 +228,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -228,9 +244,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -300,6 +316,7 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_NET_IPIP is not set # CONFIG_NET_IPGRE is not set # CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set CONFIG_SYN_COOKIES=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set @@ -380,7 +397,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set @@ -485,6 +506,7 @@ CONFIG_MTD_PHYSMAP_OF=y # CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -520,13 +542,17 @@ CONFIG_HAVE_IDE=y # # -# A new alternative FireWire stack is available with EXPERIMENTAL=y +# You can enable one or both FireWire driver stacks. # + +# +# See the help texts for more information. +# +# CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_EQUALIZER is not set @@ -573,6 +599,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_FS_ENET=y # CONFIG_FS_ENET_HAS_SCC is not set @@ -594,8 +621,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set # CONFIG_FSL_PQ_MDIO is not set # CONFIG_GIANFAR is not set +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_JME is not set @@ -685,6 +714,10 @@ CONFIG_HW_RANDOM=y CONFIG_DEVPORT=y # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y @@ -728,22 +761,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -771,6 +789,10 @@ CONFIG_DAB=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -787,9 +809,10 @@ CONFIG_JBD=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_OCFS2_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -935,6 +958,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -960,6 +984,9 @@ CONFIG_DEBUG_KERNEL=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -971,7 +998,6 @@ CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -985,22 +1011,23 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set diff --git a/arch/powerpc/configs/ep88xc_defconfig b/arch/powerpc/configs/ep88xc_defconfig index c2a439595f4..2c292e25cc0 100644 --- a/arch/powerpc/configs/ep88xc_defconfig +++ b/arch/powerpc/configs/ep88xc_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:21:53 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:31:49 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set # CONFIG_PPC_85xx is not set CONFIG_PPC_8xx=y # CONFIG_40x is not set @@ -27,15 +27,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -49,11 +50,13 @@ CONFIG_OF=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y # CONFIG_DEFAULT_UIMAGE is not set # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -100,7 +103,6 @@ CONFIG_EMBEDDED=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -113,8 +115,15 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set # CONFIG_VM_EVENT_COUNTERS is not set CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -128,13 +137,17 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_BASE_SMALL=1 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -220,6 +233,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_MATH_EMULATION is not set CONFIG_8XX_MINIMAL_FPEMU=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_PPC_NEED_DMA_SYNC_OPS=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y @@ -239,9 +253,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -280,6 +294,7 @@ CONFIG_PAGE_OFFSET=0xc0000000 CONFIG_KERNEL_START=0xc0000000 CONFIG_PHYSICAL_START=0x00000000 CONFIG_TASK_SIZE=0x80000000 +CONFIG_CONSISTENT_SIZE=0x00200000 CONFIG_NET=y # @@ -336,6 +351,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -353,7 +369,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -452,6 +472,7 @@ CONFIG_MTD_PHYSMAP_OF=y # # CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set # CONFIG_BLK_DEV is not set # CONFIG_MISC_DEVICES is not set @@ -469,7 +490,6 @@ CONFIG_HAVE_IDE=y # CONFIG_MD is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -508,6 +528,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set CONFIG_FS_ENET=y # CONFIG_FS_ENET_HAS_SCC is not set CONFIG_FS_ENET_HAS_FEC=y @@ -579,6 +600,11 @@ CONFIG_GEN_RTC=y # CONFIG_TCG_TPM is not set # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -602,22 +628,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -642,6 +653,10 @@ CONFIG_DAB=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -653,12 +668,15 @@ CONFIG_DAB=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y # CONFIG_DNOTIFY is not set # CONFIG_INOTIFY is not set +CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set @@ -775,6 +793,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -803,6 +822,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_SLUB_STATS is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -814,7 +836,6 @@ CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -827,16 +848,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -844,6 +864,9 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set diff --git a/arch/powerpc/configs/linkstation_defconfig b/arch/powerpc/configs/linkstation_defconfig index a4053ab9e24..45671e7dd2c 100644 --- a/arch/powerpc/configs/linkstation_defconfig +++ b/arch/powerpc/configs/linkstation_defconfig @@ -1,25 +1,27 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:21:54 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:31:50 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -30,15 +32,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -52,11 +55,13 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -114,7 +119,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -127,9 +131,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set # CONFIG_COMPAT_BRK is not set # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -143,6 +154,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -155,7 +170,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -237,6 +252,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -257,9 +273,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -480,6 +496,7 @@ CONFIG_IP_NF_ARP_MANGLE=m # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -498,7 +515,11 @@ CONFIG_WIRELESS_OLD_REGULATORY=y CONFIG_WIRELESS_EXT=y CONFIG_WIRELESS_EXT_SYSFS=y # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -647,7 +668,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set CONFIG_EEPROM_LEGACY=m +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -670,10 +693,6 @@ CONFIG_BLK_DEV_SD=y # CONFIG_BLK_DEV_SR is not set CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# CONFIG_SCSI_MULTI_LUN=y # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -691,6 +710,7 @@ CONFIG_SCSI_WAIT_SCAN=m CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_CXGB3_ISCSI is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -699,6 +719,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -718,7 +739,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -802,14 +822,17 @@ CONFIG_PATA_SIL680=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -846,6 +869,7 @@ CONFIG_TULIP_MMIO=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -865,8 +889,10 @@ CONFIG_R8169=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set # CONFIG_FSL_PQ_MDIO is not set # CONFIG_GIANFAR is not set +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -1074,13 +1100,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -1135,6 +1165,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -1169,23 +1200,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -# CONFIG_DAB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1245,6 +1262,7 @@ CONFIG_USB_MON=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y # CONFIG_USB_EHCI_ROOT_HUB_TT is not set # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1254,9 +1272,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=y -CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PPC_OF_BE=y # CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set +CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PCI=y CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y @@ -1423,6 +1441,7 @@ CONFIG_RTC_DRV_RS5C372=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1450,6 +1469,10 @@ CONFIG_RTC_DRV_RS5C372=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1469,14 +1492,16 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y -CONFIG_FILE_LOCKING=y CONFIG_XFS_FS=m # CONFIG_XFS_QUOTA is not set # CONFIG_XFS_POSIX_ACL is not set # CONFIG_XFS_RT is not set # CONFIG_XFS_DEBUG is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1548,6 +1573,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y CONFIG_NFSD=m CONFIG_NFSD_V3=y @@ -1578,7 +1604,7 @@ CONFIG_CIFS=m # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y -CONFIG_NLS=m +CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=m # CONFIG_NLS_CODEPAGE_737 is not set @@ -1645,6 +1671,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1675,6 +1702,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -1686,7 +1716,6 @@ CONFIG_DEBUG_MEMORY_INIT=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -1700,16 +1729,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -1717,6 +1745,8 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set diff --git a/arch/powerpc/configs/mgcoge_defconfig b/arch/powerpc/configs/mgcoge_defconfig index 31e1df66515..e9491c1c3f3 100644 --- a/arch/powerpc/configs/mgcoge_defconfig +++ b/arch/powerpc/configs/mgcoge_defconfig @@ -1,25 +1,27 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:21:55 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:31:51 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -30,15 +32,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -53,6 +56,7 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y # CONFIG_DEFAULT_UIMAGE is not set CONFIG_HIBERNATE_32=y CONFIG_ARCH_HIBERNATION_POSSIBLE=y @@ -60,6 +64,7 @@ CONFIG_ARCH_HIBERNATION_POSSIBLE=y # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -105,7 +110,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_ALL=y # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -119,8 +123,15 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -134,6 +145,11 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# +# CONFIG_GCOV_KERNEL is not set # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -141,7 +157,7 @@ CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_INTEGRITY is not set # @@ -225,6 +241,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -240,9 +257,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -313,6 +330,7 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_NET_IPIP is not set # CONFIG_NET_IPGRE is not set # CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set CONFIG_SYN_COOKIES=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set @@ -374,7 +392,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set @@ -484,6 +506,7 @@ CONFIG_MTD_PHYSMAP_OF=y # CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -523,13 +546,17 @@ CONFIG_HAVE_IDE=y # # -# A new alternative FireWire stack is available with EXPERIMENTAL=y +# You can enable one or both FireWire driver stacks. # + +# +# See the help texts for more information. +# +# CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_EQUALIZER is not set @@ -577,6 +604,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_FS_ENET=y CONFIG_FS_ENET_HAS_SCC=y @@ -654,6 +682,10 @@ CONFIG_HW_RANDOM=y CONFIG_DEVPORT=y # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y @@ -697,22 +729,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -# CONFIG_DAB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -740,6 +757,10 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -757,9 +778,10 @@ CONFIG_JBD=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_OCFS2_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -916,6 +938,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -941,6 +964,9 @@ CONFIG_DEBUG_KERNEL=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -952,7 +978,6 @@ CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -966,16 +991,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -983,9 +1007,12 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_DYNAMIC_DEBUG is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_PPC_EMULATED_STATS is not set # CONFIG_CODE_PATCHING_SELFTEST is not set # CONFIG_FTR_FIXUP_SELFTEST is not set # CONFIG_MSI_BITMAP_SELFTEST is not set diff --git a/arch/powerpc/configs/mgsuvd_defconfig b/arch/powerpc/configs/mgsuvd_defconfig index 24fa90792c5..1ae85a3b294 100644 --- a/arch/powerpc/configs/mgsuvd_defconfig +++ b/arch/powerpc/configs/mgsuvd_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:21:55 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:31:52 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set # CONFIG_PPC_85xx is not set CONFIG_PPC_8xx=y # CONFIG_40x is not set @@ -27,15 +27,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -48,11 +49,13 @@ CONFIG_OF=y # CONFIG_PPC_UDBG_16550 is not set # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y +CONFIG_DTC=y # CONFIG_DEFAULT_UIMAGE is not set # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -102,7 +105,6 @@ CONFIG_EMBEDDED=y # CONFIG_SYSCTL_SYSCALL is not set CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set # CONFIG_HOTPLUG is not set CONFIG_PRINTK=y # CONFIG_BUG is not set @@ -115,7 +117,14 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set # CONFIG_VM_EVENT_COUNTERS is not set +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -129,6 +138,11 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# +# CONFIG_GCOV_KERNEL is not set # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -136,7 +150,7 @@ CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=1 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -222,6 +236,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_PPC_NEED_DMA_SYNC_OPS=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y @@ -241,9 +256,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -281,6 +296,7 @@ CONFIG_PAGE_OFFSET=0xc0000000 CONFIG_KERNEL_START=0xc0000000 CONFIG_PHYSICAL_START=0x00000000 CONFIG_TASK_SIZE=0x80000000 +CONFIG_CONSISTENT_SIZE=0x00200000 CONFIG_NET=y # @@ -342,6 +358,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -359,7 +376,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -463,6 +484,7 @@ CONFIG_MTD_PHYSMAP_OF=y # # CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -492,7 +514,6 @@ CONFIG_HAVE_IDE=y # CONFIG_MD is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -531,6 +552,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set CONFIG_FS_ENET=y CONFIG_FS_ENET_HAS_SCC=y # CONFIG_FS_ENET_HAS_FEC is not set @@ -602,6 +624,11 @@ CONFIG_GEN_RTC=y # CONFIG_TCG_TPM is not set # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -625,22 +652,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -# CONFIG_DAB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -665,6 +677,10 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -687,10 +703,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -823,6 +841,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -844,24 +863,14 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_DYNAMIC_DEBUG is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 +# CONFIG_PPC_EMULATED_STATS is not set # CONFIG_IRQSTACKS is not set # CONFIG_VIRQ_DEBUG is not set # CONFIG_PPC_EARLY_DEBUG is not set diff --git a/arch/powerpc/configs/mpc7448_hpc2_defconfig b/arch/powerpc/configs/mpc7448_hpc2_defconfig index 642ab67c843..f23428c3b34 100644 --- a/arch/powerpc/configs/mpc7448_hpc2_defconfig +++ b/arch/powerpc/configs/mpc7448_hpc2_defconfig @@ -1,25 +1,27 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:21:56 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:31:53 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y CONFIG_ALTIVEC=y CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -30,15 +32,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -52,11 +55,13 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -106,7 +111,6 @@ CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -119,9 +123,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -134,6 +145,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -141,7 +156,7 @@ CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 # CONFIG_MODULES is not set CONFIG_BLOCK=y -CONFIG_LBD=y +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -220,6 +235,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -240,9 +256,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -348,6 +364,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -365,7 +382,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -385,6 +406,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_CONNECTOR is not set # CONFIG_MTD is not set CONFIG_OF_DEVICE=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -416,6 +438,7 @@ CONFIG_MISC_DEVICES=y # EEPROM support # # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -438,10 +461,6 @@ CONFIG_BLK_DEV_SD=y # CONFIG_BLK_DEV_SR is not set # CONFIG_CHR_DEV_SG is not set # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -458,6 +477,7 @@ CONFIG_BLK_DEV_SD=y CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_CXGB3_ISCSI is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -466,6 +486,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -485,7 +506,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -568,14 +588,17 @@ CONFIG_SATA_MV=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -642,6 +665,7 @@ CONFIG_8139TOO=y # CONFIG_SMSC9420 is not set # CONFIG_SUNDANCE is not set # CONFIG_TLAN is not set +# CONFIG_KS8842 is not set # CONFIG_VIA_RHINE is not set # CONFIG_SC92031 is not set # CONFIG_ATL2 is not set @@ -663,7 +687,9 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_TSI108_ETH=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -785,6 +811,11 @@ CONFIG_GEN_RTC=y CONFIG_DEVPORT=y # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -824,22 +855,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -896,6 +912,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -915,11 +935,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1038,6 +1059,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1063,22 +1085,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_BOOTX_TEXT is not set diff --git a/arch/powerpc/configs/mpc8272_ads_defconfig b/arch/powerpc/configs/mpc8272_ads_defconfig index cb966ca2ce8..02716f72db6 100644 --- a/arch/powerpc/configs/mpc8272_ads_defconfig +++ b/arch/powerpc/configs/mpc8272_ads_defconfig @@ -1,25 +1,27 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:21:57 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:31:54 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -30,15 +32,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -53,11 +56,13 @@ CONFIG_OF=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -99,7 +104,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_ALL=y # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -112,9 +116,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -128,6 +139,10 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -135,7 +150,7 @@ CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_INTEGRITY is not set # @@ -216,6 +231,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -231,9 +247,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -303,6 +319,7 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_NET_IPIP is not set # CONFIG_NET_IPGRE is not set # CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set CONFIG_SYN_COOKIES=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set @@ -383,7 +400,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set @@ -489,6 +510,7 @@ CONFIG_MTD_PHYSMAP_OF=y # CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -524,13 +546,17 @@ CONFIG_HAVE_IDE=y # # -# A new alternative FireWire stack is available with EXPERIMENTAL=y +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # +# CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_EQUALIZER is not set @@ -577,6 +603,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_FS_ENET=y # CONFIG_FS_ENET_HAS_SCC is not set @@ -598,8 +625,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set # CONFIG_FSL_PQ_MDIO is not set # CONFIG_GIANFAR is not set +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_JME is not set @@ -671,12 +700,13 @@ CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_KEYBOARD=y CONFIG_KEYBOARD_ATKBD=y -# CONFIG_KEYBOARD_SUNKBD is not set # CONFIG_KEYBOARD_LKKBD is not set -# CONFIG_KEYBOARD_XTKBD is not set +# CONFIG_KEYBOARD_GPIO is not set +# CONFIG_KEYBOARD_MATRIX is not set # CONFIG_KEYBOARD_NEWTON is not set # CONFIG_KEYBOARD_STOWAWAY is not set -# CONFIG_KEYBOARD_GPIO is not set +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set CONFIG_INPUT_MOUSE=y CONFIG_MOUSE_PS2=y CONFIG_MOUSE_PS2_ALPS=y @@ -741,6 +771,10 @@ CONFIG_HW_RANDOM=y CONFIG_DEVPORT=y # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y @@ -784,22 +818,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -828,6 +847,10 @@ CONFIG_DAB=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -847,9 +870,10 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_OCFS2_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -998,6 +1022,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1028,6 +1053,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -1039,7 +1067,6 @@ CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -1053,22 +1080,23 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set diff --git a/arch/powerpc/configs/mpc83xx_defconfig b/arch/powerpc/configs/mpc83xx_defconfig index 433c303eb82..4a96cb6925b 100644 --- a/arch/powerpc/configs/mpc83xx_defconfig +++ b/arch/powerpc/configs/mpc83xx_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:21:58 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:31:55 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_FSL_EMB_PERFMON is not set # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -54,6 +57,7 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y CONFIG_REDBOOT=y CONFIG_ARCH_SUSPEND_POSSIBLE=y @@ -61,6 +65,7 @@ CONFIG_ARCH_SUSPEND_POSSIBLE=y # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -110,7 +115,6 @@ CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -123,8 +127,15 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -138,6 +149,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -150,7 +165,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -192,6 +207,7 @@ CONFIG_MPC837x_MDS=y CONFIG_MPC837x_RDB=y CONFIG_SBC834x=y CONFIG_ASP834x=y +# CONFIG_KMETER1 is not set CONFIG_PPC_MPC831x=y CONFIG_PPC_MPC832x=y CONFIG_PPC_MPC834x=y @@ -241,6 +257,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -261,9 +278,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -374,6 +391,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -391,7 +409,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -507,6 +529,7 @@ CONFIG_MTD_NAND_FSL_ELBC=y CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -542,7 +565,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -565,10 +590,6 @@ CONFIG_BLK_DEV_SD=y # CONFIG_BLK_DEV_SR is not set CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -586,6 +607,7 @@ CONFIG_SCSI_WAIT_SCAN=m CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_CXGB3_ISCSI is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -594,6 +616,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -613,7 +636,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -697,14 +719,17 @@ CONFIG_ATA_SFF=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -751,6 +776,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -770,11 +796,13 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y CONFIG_UCC_GETH=y # CONFIG_UGETH_MAGIC_PACKET is not set # CONFIG_UGETH_TX_ON_DEMAND is not set +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -965,13 +993,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y @@ -1050,6 +1082,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -1104,24 +1137,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1159,7 +1177,7 @@ CONFIG_HID_BELKIN=y CONFIG_HID_CHERRY=y CONFIG_HID_CHICONY=y CONFIG_HID_CYPRESS=y -# CONFIG_DRAGONRISE_FF is not set +# CONFIG_HID_DRAGONRISE is not set CONFIG_HID_EZKEY=y # CONFIG_HID_KYE is not set CONFIG_HID_GYRATION=y @@ -1176,10 +1194,11 @@ CONFIG_HID_PETALYNX=y CONFIG_HID_SAMSUNG=y CONFIG_HID_SONY=y CONFIG_HID_SUNPLUS=y -# CONFIG_GREENASIA_FF is not set +# CONFIG_HID_GREENASIA is not set +# CONFIG_HID_SMARTJOYPLUS is not set # CONFIG_HID_TOPSEED is not set -CONFIG_THRUSTMASTER_FF=m -CONFIG_ZEROPLUS_FF=m +# CONFIG_HID_THRUSTMASTER is not set +# CONFIG_HID_ZEROPLUS is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -1205,6 +1224,7 @@ CONFIG_USB_MON=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_ROOT_HUB_TT=y # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1291,6 +1311,10 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1310,10 +1334,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1377,6 +1403,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1413,7 +1440,46 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set -# CONFIG_NLS is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +# CONFIG_NLS_CODEPAGE_437 is not set +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +# CONFIG_NLS_ISO8859_1 is not set +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set # CONFIG_DLM is not set CONFIG_UCC_FAST=y CONFIG_UCC=y @@ -1438,6 +1504,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1461,22 +1528,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_BOOTX_TEXT is not set diff --git a/arch/powerpc/configs/mpc85xx_defconfig b/arch/powerpc/configs/mpc85xx_defconfig index c162724fed4..ada595898af 100644 --- a/arch/powerpc/configs/mpc85xx_defconfig +++ b/arch/powerpc/configs/mpc85xx_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc2 -# Tue Apr 21 15:40:23 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:31:55 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set CONFIG_PPC_85xx=y # CONFIG_PPC_8xx is not set # CONFIG_40x is not set @@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -57,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -116,7 +119,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_ALL=y CONFIG_KALLSYMS_EXTRA_PASS=y -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -129,9 +131,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -146,6 +155,11 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# +# CONFIG_GCOV_KERNEL is not set # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -158,7 +172,7 @@ CONFIG_MODULE_FORCE_UNLOAD=y CONFIG_MODVERSIONS=y # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -CONFIG_LBD=y +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -191,6 +205,7 @@ CONFIG_MPC8536_DS=y CONFIG_MPC85xx_DS=y CONFIG_SOCRATES=y CONFIG_KSI8560=y +# CONFIG_XES_MPC85xx is not set CONFIG_STX_GP3=y CONFIG_TQM8540=y CONFIG_TQM8541=y @@ -241,7 +256,9 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=m CONFIG_MATH_EMULATION=y -# CONFIG_IOMMU_HELPER is not set +CONFIG_IOMMU_HELPER=y +CONFIG_SWIOTLB=y +CONFIG_PPC_NEED_DMA_SYNC_OPS=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -260,9 +277,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -296,7 +313,8 @@ CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_IOV is not set # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set -# CONFIG_HAS_RAPIDIO is not set +CONFIG_HAS_RAPIDIO=y +# CONFIG_RAPIDIO is not set # # Advanced setup @@ -406,6 +424,7 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -424,7 +443,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -450,6 +473,7 @@ CONFIG_EXTRA_FIRMWARE="" CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -485,7 +509,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set CONFIG_EEPROM_LEGACY=y +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -509,10 +535,6 @@ CONFIG_BLK_DEV_SR=y # CONFIG_BLK_DEV_SR_VENDOR is not set CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# CONFIG_SCSI_MULTI_LUN=y # CONFIG_SCSI_CONSTANTS is not set CONFIG_SCSI_LOGGING=y @@ -530,6 +552,7 @@ CONFIG_SCSI_WAIT_SCAN=m CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_CXGB3_ISCSI is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -538,6 +561,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -557,7 +581,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -641,14 +664,17 @@ CONFIG_PATA_ALI=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_DUMMY=y # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -695,6 +721,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_FS_ENET=y CONFIG_FS_ENET_HAS_SCC=y @@ -718,11 +745,13 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y CONFIG_UCC_GETH=y # CONFIG_UGETH_MAGIC_PACKET is not set # CONFIG_UGETH_TX_ON_DEMAND is not set +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -897,6 +926,7 @@ CONFIG_I2C_HELPER_AUTO=y # I2C system bus drivers (mostly embedded / system-on-chip) # CONFIG_I2C_CPM=m +# CONFIG_I2C_DESIGNWARE is not set # CONFIG_I2C_GPIO is not set CONFIG_I2C_MPC=y # CONFIG_I2C_OCORES is not set @@ -927,13 +957,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y @@ -987,76 +1021,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -CONFIG_DVB_CORE=m -CONFIG_VIDEO_MEDIA=m - -# -# Multimedia drivers -# -# CONFIG_MEDIA_ATTACH is not set -CONFIG_MEDIA_TUNER=m -# CONFIG_MEDIA_TUNER_CUSTOMISE is not set -CONFIG_MEDIA_TUNER_SIMPLE=m -CONFIG_MEDIA_TUNER_TDA8290=m -CONFIG_MEDIA_TUNER_TDA9887=m -CONFIG_MEDIA_TUNER_TEA5761=m -CONFIG_MEDIA_TUNER_TEA5767=m -CONFIG_MEDIA_TUNER_MT20XX=m -CONFIG_MEDIA_TUNER_XC2028=m -CONFIG_MEDIA_TUNER_XC5000=m -CONFIG_MEDIA_TUNER_MC44S803=m -# CONFIG_DVB_DYNAMIC_MINORS is not set -CONFIG_DVB_CAPTURE_DRIVERS=y - -# -# Supported SAA7146 based PCI Adapters -# -# CONFIG_TTPCI_EEPROM is not set -# CONFIG_DVB_BUDGET_CORE is not set - -# -# Supported USB Adapters -# -# CONFIG_DVB_USB is not set -# CONFIG_DVB_TTUSB_BUDGET is not set -# CONFIG_DVB_TTUSB_DEC is not set -# CONFIG_DVB_SIANO_SMS1XXX is not set - -# -# Supported FlexCopII (B2C2) Adapters -# -# CONFIG_DVB_B2C2_FLEXCOP is not set - -# -# Supported BT878 Adapters -# - -# -# Supported Pluto2 Adapters -# -# CONFIG_DVB_PLUTO2 is not set - -# -# Supported SDMC DM1105 Adapters -# -# CONFIG_DVB_DM1105 is not set - -# -# Supported DVB Frontends -# -# CONFIG_DVB_FE_CUSTOMISE is not set -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1096,6 +1063,11 @@ CONFIG_SND_VERBOSE_PROCFS=y # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set CONFIG_SND_VMASTER=y +# CONFIG_SND_RAWMIDI_SEQ is not set +# CONFIG_SND_OPL3_LIB_SEQ is not set +# CONFIG_SND_OPL4_LIB_SEQ is not set +# CONFIG_SND_SBAWE_SEQ is not set +# CONFIG_SND_EMU10K1_SEQ is not set CONFIG_SND_AC97_CODEC=y CONFIG_SND_DRIVERS=y # CONFIG_SND_DUMMY is not set @@ -1122,6 +1094,7 @@ CONFIG_SND_PCI=y # CONFIG_SND_CS4281 is not set # CONFIG_SND_CS46XX is not set # CONFIG_SND_CS5530 is not set +# CONFIG_SND_CTXFI is not set # CONFIG_SND_DARLA20 is not set # CONFIG_SND_GINA20 is not set # CONFIG_SND_LAYLA20 is not set @@ -1152,6 +1125,7 @@ CONFIG_SND_PCI=y CONFIG_SND_INTEL8X0=y # CONFIG_SND_INTEL8X0M is not set # CONFIG_SND_KORG1212 is not set +# CONFIG_SND_LX6464ES is not set # CONFIG_SND_MAESTRO3 is not set # CONFIG_SND_MIXART is not set # CONFIG_SND_NM256 is not set @@ -1196,7 +1170,7 @@ CONFIG_HID_BELKIN=y CONFIG_HID_CHERRY=y CONFIG_HID_CHICONY=y CONFIG_HID_CYPRESS=y -# CONFIG_DRAGONRISE_FF is not set +# CONFIG_HID_DRAGONRISE is not set CONFIG_HID_EZKEY=y # CONFIG_HID_KYE is not set CONFIG_HID_GYRATION=y @@ -1213,10 +1187,11 @@ CONFIG_HID_PETALYNX=y CONFIG_HID_SAMSUNG=y CONFIG_HID_SONY=y CONFIG_HID_SUNPLUS=y -# CONFIG_GREENASIA_FF is not set +# CONFIG_HID_GREENASIA is not set +# CONFIG_HID_SMARTJOYPLUS is not set # CONFIG_HID_TOPSEED is not set -CONFIG_THRUSTMASTER_FF=m -CONFIG_ZEROPLUS_FF=m +# CONFIG_HID_THRUSTMASTER is not set +# CONFIG_HID_ZEROPLUS is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -1242,6 +1217,7 @@ CONFIG_USB_MON=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_ROOT_HUB_TT=y # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1251,9 +1227,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=y -CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PPC_OF_BE=y CONFIG_USB_OHCI_HCD_PPC_OF_LE=y +CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PCI=y CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y @@ -1352,8 +1328,6 @@ CONFIG_EDAC=y # CONFIG_EDAC_DEBUG is not set CONFIG_EDAC_MM_EDAC=y CONFIG_EDAC_MPC85XX=y -# CONFIG_EDAC_AMD8131 is not set -# CONFIG_EDAC_AMD8111 is not set CONFIG_RTC_LIB=y CONFIG_RTC_CLASS=y CONFIG_RTC_HCTOSYS=y @@ -1385,6 +1359,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1425,6 +1400,10 @@ CONFIG_DMA_ENGINE=y # CONFIG_DMATEST is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1445,11 +1424,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1524,6 +1504,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y CONFIG_NFSD=y # CONFIG_NFSD_V3 is not set @@ -1628,6 +1609,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1658,6 +1640,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -1670,7 +1655,6 @@ CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -1684,16 +1668,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -1702,9 +1685,13 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_PPC_EMULATED_STATS is not set # CONFIG_CODE_PATCHING_SELFTEST is not set # CONFIG_FTR_FIXUP_SELFTEST is not set # CONFIG_MSI_BITMAP_SELFTEST is not set diff --git a/arch/powerpc/configs/mpc85xx_smp_defconfig b/arch/powerpc/configs/mpc85xx_smp_defconfig index 1aa1c508d60..db082ce5a1c 100644 --- a/arch/powerpc/configs/mpc85xx_smp_defconfig +++ b/arch/powerpc/configs/mpc85xx_smp_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc2 -# Tue Apr 21 15:41:18 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:31:56 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set CONFIG_PPC_85xx=y # CONFIG_PPC_8xx is not set # CONFIG_40x is not set @@ -35,15 +35,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -58,11 +59,13 @@ CONFIG_PPC_UDBG_16550=y CONFIG_GENERIC_TBSYNC=y CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -117,7 +120,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_ALL=y CONFIG_KALLSYMS_EXTRA_PASS=y -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -130,9 +132,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -148,6 +157,11 @@ CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_USE_GENERIC_SMP_HELPERS=y CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# +# CONFIG_GCOV_KERNEL is not set # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -161,7 +175,7 @@ CONFIG_MODVERSIONS=y # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y -CONFIG_LBD=y +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -194,6 +208,7 @@ CONFIG_MPC8536_DS=y CONFIG_MPC85xx_DS=y CONFIG_SOCRATES=y CONFIG_KSI8560=y +# CONFIG_XES_MPC85xx is not set CONFIG_STX_GP3=y CONFIG_TQM8540=y CONFIG_TQM8541=y @@ -244,7 +259,9 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=m CONFIG_MATH_EMULATION=y -# CONFIG_IOMMU_HELPER is not set +CONFIG_IOMMU_HELPER=y +CONFIG_SWIOTLB=y +CONFIG_PPC_NEED_DMA_SYNC_OPS=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -264,9 +281,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -300,7 +317,8 @@ CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_IOV is not set # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set -# CONFIG_HAS_RAPIDIO is not set +CONFIG_HAS_RAPIDIO=y +# CONFIG_RAPIDIO is not set # # Advanced setup @@ -410,6 +428,7 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -428,7 +447,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -454,6 +477,7 @@ CONFIG_EXTRA_FIRMWARE="" CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -489,7 +513,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set CONFIG_EEPROM_LEGACY=y +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -513,10 +539,6 @@ CONFIG_BLK_DEV_SR=y # CONFIG_BLK_DEV_SR_VENDOR is not set CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# CONFIG_SCSI_MULTI_LUN=y # CONFIG_SCSI_CONSTANTS is not set CONFIG_SCSI_LOGGING=y @@ -534,6 +556,7 @@ CONFIG_SCSI_WAIT_SCAN=m CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_CXGB3_ISCSI is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -542,6 +565,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -561,7 +585,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -645,14 +668,17 @@ CONFIG_PATA_ALI=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_DUMMY=y # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -699,6 +725,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_FS_ENET=y CONFIG_FS_ENET_HAS_SCC=y @@ -722,11 +749,13 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y CONFIG_UCC_GETH=y # CONFIG_UGETH_MAGIC_PACKET is not set # CONFIG_UGETH_TX_ON_DEMAND is not set +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -901,6 +930,7 @@ CONFIG_I2C_HELPER_AUTO=y # I2C system bus drivers (mostly embedded / system-on-chip) # CONFIG_I2C_CPM=m +# CONFIG_I2C_DESIGNWARE is not set # CONFIG_I2C_GPIO is not set CONFIG_I2C_MPC=y # CONFIG_I2C_OCORES is not set @@ -931,13 +961,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y @@ -991,76 +1025,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -CONFIG_DVB_CORE=m -CONFIG_VIDEO_MEDIA=m - -# -# Multimedia drivers -# -# CONFIG_MEDIA_ATTACH is not set -CONFIG_MEDIA_TUNER=m -# CONFIG_MEDIA_TUNER_CUSTOMISE is not set -CONFIG_MEDIA_TUNER_SIMPLE=m -CONFIG_MEDIA_TUNER_TDA8290=m -CONFIG_MEDIA_TUNER_TDA9887=m -CONFIG_MEDIA_TUNER_TEA5761=m -CONFIG_MEDIA_TUNER_TEA5767=m -CONFIG_MEDIA_TUNER_MT20XX=m -CONFIG_MEDIA_TUNER_XC2028=m -CONFIG_MEDIA_TUNER_XC5000=m -CONFIG_MEDIA_TUNER_MC44S803=m -# CONFIG_DVB_DYNAMIC_MINORS is not set -CONFIG_DVB_CAPTURE_DRIVERS=y - -# -# Supported SAA7146 based PCI Adapters -# -# CONFIG_TTPCI_EEPROM is not set -# CONFIG_DVB_BUDGET_CORE is not set - -# -# Supported USB Adapters -# -# CONFIG_DVB_USB is not set -# CONFIG_DVB_TTUSB_BUDGET is not set -# CONFIG_DVB_TTUSB_DEC is not set -# CONFIG_DVB_SIANO_SMS1XXX is not set - -# -# Supported FlexCopII (B2C2) Adapters -# -# CONFIG_DVB_B2C2_FLEXCOP is not set - -# -# Supported BT878 Adapters -# - -# -# Supported Pluto2 Adapters -# -# CONFIG_DVB_PLUTO2 is not set - -# -# Supported SDMC DM1105 Adapters -# -# CONFIG_DVB_DM1105 is not set - -# -# Supported DVB Frontends -# -# CONFIG_DVB_FE_CUSTOMISE is not set -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1100,6 +1067,11 @@ CONFIG_SND_VERBOSE_PROCFS=y # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set CONFIG_SND_VMASTER=y +# CONFIG_SND_RAWMIDI_SEQ is not set +# CONFIG_SND_OPL3_LIB_SEQ is not set +# CONFIG_SND_OPL4_LIB_SEQ is not set +# CONFIG_SND_SBAWE_SEQ is not set +# CONFIG_SND_EMU10K1_SEQ is not set CONFIG_SND_AC97_CODEC=y CONFIG_SND_DRIVERS=y # CONFIG_SND_DUMMY is not set @@ -1126,6 +1098,7 @@ CONFIG_SND_PCI=y # CONFIG_SND_CS4281 is not set # CONFIG_SND_CS46XX is not set # CONFIG_SND_CS5530 is not set +# CONFIG_SND_CTXFI is not set # CONFIG_SND_DARLA20 is not set # CONFIG_SND_GINA20 is not set # CONFIG_SND_LAYLA20 is not set @@ -1156,6 +1129,7 @@ CONFIG_SND_PCI=y CONFIG_SND_INTEL8X0=y # CONFIG_SND_INTEL8X0M is not set # CONFIG_SND_KORG1212 is not set +# CONFIG_SND_LX6464ES is not set # CONFIG_SND_MAESTRO3 is not set # CONFIG_SND_MIXART is not set # CONFIG_SND_NM256 is not set @@ -1200,7 +1174,7 @@ CONFIG_HID_BELKIN=y CONFIG_HID_CHERRY=y CONFIG_HID_CHICONY=y CONFIG_HID_CYPRESS=y -# CONFIG_DRAGONRISE_FF is not set +# CONFIG_HID_DRAGONRISE is not set CONFIG_HID_EZKEY=y # CONFIG_HID_KYE is not set CONFIG_HID_GYRATION=y @@ -1217,10 +1191,11 @@ CONFIG_HID_PETALYNX=y CONFIG_HID_SAMSUNG=y CONFIG_HID_SONY=y CONFIG_HID_SUNPLUS=y -# CONFIG_GREENASIA_FF is not set +# CONFIG_HID_GREENASIA is not set +# CONFIG_HID_SMARTJOYPLUS is not set # CONFIG_HID_TOPSEED is not set -CONFIG_THRUSTMASTER_FF=m -CONFIG_ZEROPLUS_FF=m +# CONFIG_HID_THRUSTMASTER is not set +# CONFIG_HID_ZEROPLUS is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -1246,6 +1221,7 @@ CONFIG_USB_MON=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_ROOT_HUB_TT=y # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1255,9 +1231,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=y -CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PPC_OF_BE=y CONFIG_USB_OHCI_HCD_PPC_OF_LE=y +CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PCI=y CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y @@ -1356,8 +1332,6 @@ CONFIG_EDAC=y # CONFIG_EDAC_DEBUG is not set CONFIG_EDAC_MM_EDAC=y CONFIG_EDAC_MPC85XX=y -# CONFIG_EDAC_AMD8131 is not set -# CONFIG_EDAC_AMD8111 is not set CONFIG_RTC_LIB=y CONFIG_RTC_CLASS=y CONFIG_RTC_HCTOSYS=y @@ -1389,6 +1363,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1429,6 +1404,10 @@ CONFIG_DMA_ENGINE=y # CONFIG_DMATEST is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1449,11 +1428,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1528,6 +1508,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y CONFIG_NFSD=y # CONFIG_NFSD_V3 is not set @@ -1632,6 +1613,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1662,6 +1644,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -1674,7 +1659,6 @@ CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -1688,16 +1672,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -1706,9 +1689,13 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_PPC_EMULATED_STATS is not set # CONFIG_CODE_PATCHING_SELFTEST is not set # CONFIG_FTR_FIXUP_SELFTEST is not set # CONFIG_MSI_BITMAP_SELFTEST is not set diff --git a/arch/powerpc/configs/mpc866_ads_defconfig b/arch/powerpc/configs/mpc866_ads_defconfig index 3add6f62b21..6809b61ed3d 100644 --- a/arch/powerpc/configs/mpc866_ads_defconfig +++ b/arch/powerpc/configs/mpc866_ads_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:00 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:31:57 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set # CONFIG_PPC_85xx is not set CONFIG_PPC_8xx=y # CONFIG_40x is not set @@ -27,15 +27,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -48,11 +49,13 @@ CONFIG_OF=y # CONFIG_PPC_UDBG_16550 is not set # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y +CONFIG_DTC=y # CONFIG_DEFAULT_UIMAGE is not set # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -98,7 +101,6 @@ CONFIG_EMBEDDED=y # CONFIG_SYSCTL_SYSCALL is not set CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set # CONFIG_HOTPLUG is not set CONFIG_PRINTK=y # CONFIG_BUG is not set @@ -111,8 +113,15 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set # CONFIG_VM_EVENT_COUNTERS is not set CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -126,6 +135,10 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -133,7 +146,7 @@ CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=1 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -219,6 +232,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_PPC_NEED_DMA_SYNC_OPS=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y @@ -238,9 +252,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -278,6 +292,7 @@ CONFIG_PAGE_OFFSET=0xc0000000 CONFIG_KERNEL_START=0xc0000000 CONFIG_PHYSICAL_START=0x00000000 CONFIG_TASK_SIZE=0x80000000 +CONFIG_CONSISTENT_SIZE=0x00200000 CONFIG_NET=y # @@ -339,6 +354,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -356,7 +372,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -374,6 +394,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_CONNECTOR is not set # CONFIG_MTD is not set CONFIG_OF_DEVICE=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -407,7 +428,6 @@ CONFIG_HAVE_IDE=y # CONFIG_MD is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -446,6 +466,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set CONFIG_FS_ENET=y CONFIG_FS_ENET_HAS_SCC=y CONFIG_FS_ENET_HAS_FEC=y @@ -453,6 +474,7 @@ CONFIG_FS_ENET_MDIO_FEC=y CONFIG_NETDEV_1000=y # CONFIG_FSL_PQ_MDIO is not set # CONFIG_GIANFAR is not set +# CONFIG_MV643XX_ETH is not set CONFIG_NETDEV_10000=y # @@ -496,11 +518,11 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_KEYBOARD=y CONFIG_KEYBOARD_ATKBD=y -# CONFIG_KEYBOARD_SUNKBD is not set # CONFIG_KEYBOARD_LKKBD is not set -# CONFIG_KEYBOARD_XTKBD is not set # CONFIG_KEYBOARD_NEWTON is not set # CONFIG_KEYBOARD_STOWAWAY is not set +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set CONFIG_INPUT_MOUSE=y CONFIG_MOUSE_PS2=y CONFIG_MOUSE_PS2_ALPS=y @@ -562,6 +584,11 @@ CONFIG_GEN_RTC=y # CONFIG_TCG_TPM is not set # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -597,22 +624,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -664,6 +676,10 @@ CONFIG_USB_SUPPORT=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -685,10 +701,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -808,6 +826,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -831,22 +850,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_PPC_EARLY_DEBUG is not set diff --git a/arch/powerpc/configs/mpc86xx_defconfig b/arch/powerpc/configs/mpc86xx_defconfig index 5bb1b8eb0b4..0e8684a3138 100644 --- a/arch/powerpc/configs/mpc86xx_defconfig +++ b/arch/powerpc/configs/mpc86xx_defconfig @@ -1,26 +1,28 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:00 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:31:58 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_PHYS_64BIT is not set CONFIG_ALTIVEC=y CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y CONFIG_SMP=y CONFIG_NR_CPUS=2 CONFIG_PPC32=y @@ -32,15 +34,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -55,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y CONFIG_GENERIC_TBSYNC=y CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -114,7 +119,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_ALL=y CONFIG_KALLSYMS_EXTRA_PASS=y -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -127,9 +131,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -144,6 +155,10 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_USE_GENERIC_SMP_HELPERS=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -157,7 +172,7 @@ CONFIG_MODVERSIONS=y # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y -CONFIG_LBD=y +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -236,7 +251,9 @@ CONFIG_BINFMT_ELF=y # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set # CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=m -# CONFIG_IOMMU_HELPER is not set +CONFIG_IOMMU_HELPER=y +CONFIG_SWIOTLB=y +CONFIG_PPC_NEED_DMA_SYNC_OPS=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -258,9 +275,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -403,6 +420,7 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -421,7 +439,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -447,6 +469,7 @@ CONFIG_EXTRA_FIRMWARE="" CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -482,7 +505,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set CONFIG_EEPROM_LEGACY=y +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -506,10 +531,6 @@ CONFIG_BLK_DEV_SR=y # CONFIG_BLK_DEV_SR_VENDOR is not set CONFIG_CHR_DEV_SG=y # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# CONFIG_SCSI_MULTI_LUN=y # CONFIG_SCSI_CONSTANTS is not set CONFIG_SCSI_LOGGING=y @@ -527,6 +548,7 @@ CONFIG_SCSI_WAIT_SCAN=m CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_CXGB3_ISCSI is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -535,6 +557,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -554,7 +577,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -638,14 +660,17 @@ CONFIG_PATA_ALI=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_DUMMY=y # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -692,6 +717,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -711,8 +737,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_FSL_PQ_MDIO=y CONFIG_GIANFAR=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -913,13 +941,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y @@ -973,76 +1005,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -CONFIG_DVB_CORE=m -CONFIG_VIDEO_MEDIA=m - -# -# Multimedia drivers -# -# CONFIG_MEDIA_ATTACH is not set -CONFIG_MEDIA_TUNER=m -# CONFIG_MEDIA_TUNER_CUSTOMISE is not set -CONFIG_MEDIA_TUNER_SIMPLE=m -CONFIG_MEDIA_TUNER_TDA8290=m -CONFIG_MEDIA_TUNER_TDA9887=m -CONFIG_MEDIA_TUNER_TEA5761=m -CONFIG_MEDIA_TUNER_TEA5767=m -CONFIG_MEDIA_TUNER_MT20XX=m -CONFIG_MEDIA_TUNER_XC2028=m -CONFIG_MEDIA_TUNER_XC5000=m -CONFIG_MEDIA_TUNER_MC44S803=m -# CONFIG_DVB_DYNAMIC_MINORS is not set -CONFIG_DVB_CAPTURE_DRIVERS=y - -# -# Supported SAA7146 based PCI Adapters -# -# CONFIG_TTPCI_EEPROM is not set -# CONFIG_DVB_BUDGET_CORE is not set - -# -# Supported USB Adapters -# -# CONFIG_DVB_USB is not set -# CONFIG_DVB_TTUSB_BUDGET is not set -# CONFIG_DVB_TTUSB_DEC is not set -# CONFIG_DVB_SIANO_SMS1XXX is not set - -# -# Supported FlexCopII (B2C2) Adapters -# -# CONFIG_DVB_B2C2_FLEXCOP is not set - -# -# Supported BT878 Adapters -# - -# -# Supported Pluto2 Adapters -# -# CONFIG_DVB_PLUTO2 is not set - -# -# Supported SDMC DM1105 Adapters -# -# CONFIG_DVB_DM1105 is not set - -# -# Supported DVB Frontends -# -# CONFIG_DVB_FE_CUSTOMISE is not set -CONFIG_DAB=y -# CONFIG_USB_DABUSB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1082,6 +1047,11 @@ CONFIG_SND_VERBOSE_PROCFS=y # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set CONFIG_SND_VMASTER=y +# CONFIG_SND_RAWMIDI_SEQ is not set +# CONFIG_SND_OPL3_LIB_SEQ is not set +# CONFIG_SND_OPL4_LIB_SEQ is not set +# CONFIG_SND_SBAWE_SEQ is not set +# CONFIG_SND_EMU10K1_SEQ is not set CONFIG_SND_AC97_CODEC=y CONFIG_SND_DRIVERS=y # CONFIG_SND_DUMMY is not set @@ -1108,6 +1078,7 @@ CONFIG_SND_PCI=y # CONFIG_SND_CS4281 is not set # CONFIG_SND_CS46XX is not set # CONFIG_SND_CS5530 is not set +# CONFIG_SND_CTXFI is not set # CONFIG_SND_DARLA20 is not set # CONFIG_SND_GINA20 is not set # CONFIG_SND_LAYLA20 is not set @@ -1138,6 +1109,7 @@ CONFIG_SND_PCI=y CONFIG_SND_INTEL8X0=y # CONFIG_SND_INTEL8X0M is not set # CONFIG_SND_KORG1212 is not set +# CONFIG_SND_LX6464ES is not set # CONFIG_SND_MAESTRO3 is not set # CONFIG_SND_MIXART is not set # CONFIG_SND_NM256 is not set @@ -1182,7 +1154,7 @@ CONFIG_HID_BELKIN=y CONFIG_HID_CHERRY=y CONFIG_HID_CHICONY=y CONFIG_HID_CYPRESS=y -# CONFIG_DRAGONRISE_FF is not set +# CONFIG_HID_DRAGONRISE is not set CONFIG_HID_EZKEY=y # CONFIG_HID_KYE is not set CONFIG_HID_GYRATION=y @@ -1199,10 +1171,11 @@ CONFIG_HID_PETALYNX=y CONFIG_HID_SAMSUNG=y CONFIG_HID_SONY=y CONFIG_HID_SUNPLUS=y -# CONFIG_GREENASIA_FF is not set +# CONFIG_HID_GREENASIA is not set +# CONFIG_HID_SMARTJOYPLUS is not set # CONFIG_HID_TOPSEED is not set -CONFIG_THRUSTMASTER_FF=m -CONFIG_ZEROPLUS_FF=m +# CONFIG_HID_THRUSTMASTER is not set +# CONFIG_HID_ZEROPLUS is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -1228,6 +1201,7 @@ CONFIG_USB_MON=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y # CONFIG_USB_EHCI_ROOT_HUB_TT is not set # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1237,9 +1211,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=y -CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PPC_OF_BE=y CONFIG_USB_OHCI_HCD_PPC_OF_LE=y +CONFIG_USB_OHCI_HCD_PPC_OF=y CONFIG_USB_OHCI_HCD_PCI=y CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y @@ -1360,6 +1334,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1387,6 +1362,10 @@ CONFIG_RTC_DRV_CMOS=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1406,11 +1385,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1485,6 +1465,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y CONFIG_NFSD=y # CONFIG_NFSD_V3 is not set @@ -1586,6 +1567,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1616,6 +1598,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -1628,7 +1613,6 @@ CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -1642,16 +1626,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -1659,6 +1642,9 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set diff --git a/arch/powerpc/configs/mpc885_ads_defconfig b/arch/powerpc/configs/mpc885_ads_defconfig index 42e64ebc279..dbe8e869a82 100644 --- a/arch/powerpc/configs/mpc885_ads_defconfig +++ b/arch/powerpc/configs/mpc885_ads_defconfig @@ -1,14 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:01 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:31:59 2009 # # CONFIG_PPC64 is not set # # Processor support # -# CONFIG_6xx is not set +# CONFIG_PPC_BOOK3S_32 is not set # CONFIG_PPC_85xx is not set CONFIG_PPC_8xx=y # CONFIG_40x is not set @@ -27,15 +27,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -49,11 +50,13 @@ CONFIG_OF=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y # CONFIG_DEFAULT_UIMAGE is not set # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -100,7 +103,6 @@ CONFIG_EMBEDDED=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -113,8 +115,15 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set # CONFIG_VM_EVENT_COUNTERS is not set CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -128,13 +137,17 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_BASE_SMALL=1 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -227,6 +240,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_MATH_EMULATION is not set CONFIG_8XX_MINIMAL_FPEMU=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_PPC_NEED_DMA_SYNC_OPS=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y @@ -246,9 +260,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -287,6 +301,7 @@ CONFIG_PAGE_OFFSET=0xc0000000 CONFIG_KERNEL_START=0xc0000000 CONFIG_PHYSICAL_START=0x00000000 CONFIG_TASK_SIZE=0x80000000 +CONFIG_CONSISTENT_SIZE=0x00200000 CONFIG_NET=y # @@ -343,6 +358,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -360,7 +376,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -463,6 +483,7 @@ CONFIG_MTD_PHYSMAP_OF=y # # CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set # CONFIG_BLK_DEV is not set # CONFIG_MISC_DEVICES is not set @@ -480,7 +501,6 @@ CONFIG_HAVE_IDE=y # CONFIG_MD is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -519,6 +539,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set CONFIG_FS_ENET=y # CONFIG_FS_ENET_HAS_SCC is not set CONFIG_FS_ENET_HAS_FEC=y @@ -590,6 +611,11 @@ CONFIG_GEN_RTC=y # CONFIG_TCG_TPM is not set # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -613,22 +639,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -653,6 +664,10 @@ CONFIG_DAB=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -664,12 +679,15 @@ CONFIG_DAB=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y # CONFIG_DNOTIFY is not set # CONFIG_INOTIFY is not set +CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set @@ -786,6 +804,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -814,6 +833,9 @@ CONFIG_SCHED_DEBUG=y # CONFIG_SLUB_STATS is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -825,7 +847,6 @@ CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -838,16 +859,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set @@ -855,6 +875,9 @@ CONFIG_TRACING_SUPPORT=y # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_KMEMCHECK is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set diff --git a/arch/powerpc/configs/pq2fads_defconfig b/arch/powerpc/configs/pq2fads_defconfig index 129d80860f2..ff96bb43c32 100644 --- a/arch/powerpc/configs/pq2fads_defconfig +++ b/arch/powerpc/configs/pq2fads_defconfig @@ -1,25 +1,27 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:02 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:00 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -30,15 +32,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set @@ -53,11 +56,13 @@ CONFIG_OF=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y CONFIG_DEFAULT_UIMAGE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -103,7 +108,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_ALL=y # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -116,9 +120,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -132,6 +143,10 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -139,7 +154,7 @@ CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 # CONFIG_MODULES is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_INTEGRITY is not set # @@ -219,6 +234,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -234,9 +250,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -307,6 +323,7 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_NET_IPIP is not set # CONFIG_NET_IPGRE is not set # CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set CONFIG_SYN_COOKIES=y # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set @@ -387,7 +404,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set @@ -493,6 +514,7 @@ CONFIG_MTD_PHYSMAP_OF=y # CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -518,6 +540,7 @@ CONFIG_MISC_DEVICES=y # EEPROM support # # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y CONFIG_IDE=y @@ -583,13 +606,17 @@ CONFIG_IDE_PROC_FS=y # # -# A new alternative FireWire stack is available with EXPERIMENTAL=y +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # +# CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_EQUALIZER is not set @@ -636,6 +663,7 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_FS_ENET=y # CONFIG_FS_ENET_HAS_SCC is not set @@ -657,8 +685,10 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set # CONFIG_FSL_PQ_MDIO is not set # CONFIG_GIANFAR is not set +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_JME is not set @@ -730,12 +760,13 @@ CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_KEYBOARD=y CONFIG_KEYBOARD_ATKBD=y -# CONFIG_KEYBOARD_SUNKBD is not set # CONFIG_KEYBOARD_LKKBD is not set -# CONFIG_KEYBOARD_XTKBD is not set +# CONFIG_KEYBOARD_GPIO is not set +# CONFIG_KEYBOARD_MATRIX is not set # CONFIG_KEYBOARD_NEWTON is not set # CONFIG_KEYBOARD_STOWAWAY is not set -# CONFIG_KEYBOARD_GPIO is not set +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set CONFIG_INPUT_MOUSE=y CONFIG_MOUSE_PS2=y CONFIG_MOUSE_PS2_ALPS=y @@ -802,6 +833,10 @@ CONFIG_HW_RANDOM=y CONFIG_DEVPORT=y # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_ARCH_REQUIRE_GPIOLIB=y CONFIG_GPIOLIB=y @@ -845,22 +880,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -903,8 +923,9 @@ CONFIG_USB_GADGET_SELECTED=y # CONFIG_USB_GADGET_OMAP is not set # CONFIG_USB_GADGET_PXA25X is not set # CONFIG_USB_GADGET_PXA27X is not set -# CONFIG_USB_GADGET_S3C2410 is not set +# CONFIG_USB_GADGET_S3C_HSOTG is not set # CONFIG_USB_GADGET_IMX is not set +# CONFIG_USB_GADGET_S3C2410 is not set CONFIG_USB_GADGET_M66592=y CONFIG_USB_M66592=y # CONFIG_USB_GADGET_AMD5536UDC is not set @@ -912,9 +933,11 @@ CONFIG_USB_M66592=y # CONFIG_USB_GADGET_CI13XXX is not set # CONFIG_USB_GADGET_NET2280 is not set # CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LANGWELL is not set # CONFIG_USB_GADGET_DUMMY_HCD is not set CONFIG_USB_GADGET_DUALSPEED=y # CONFIG_USB_ZERO is not set +# CONFIG_USB_AUDIO is not set CONFIG_USB_ETH=y CONFIG_USB_ETH_RNDIS=y # CONFIG_USB_GADGETFS is not set @@ -939,6 +962,10 @@ CONFIG_USB_ETH_RNDIS=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -958,9 +985,10 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_OCFS2_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1110,6 +1138,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1140,6 +1169,9 @@ CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0 # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_DEBUG_KOBJECT is not set @@ -1151,7 +1183,6 @@ CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -1165,22 +1196,23 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# +CONFIG_FTRACE=y # CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set # CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set # CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set # CONFIG_STACK_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set diff --git a/arch/powerpc/configs/prpmc2800_defconfig b/arch/powerpc/configs/prpmc2800_defconfig index e9f287f313f..1293c465d7f 100644 --- a/arch/powerpc/configs/prpmc2800_defconfig +++ b/arch/powerpc/configs/prpmc2800_defconfig @@ -1,25 +1,27 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:03 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:01 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y CONFIG_ALTIVEC=y CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_NOT_COHERENT_CACHE=y CONFIG_CHECK_CACHE_COHERENCY=y @@ -32,15 +34,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -54,11 +57,13 @@ CONFIG_OF=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y # CONFIG_DEFAULT_UIMAGE is not set # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -114,7 +119,6 @@ CONFIG_ANON_INODES=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -127,9 +131,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -142,6 +153,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -149,7 +164,7 @@ CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 # CONFIG_MODULES is not set CONFIG_BLOCK=y -CONFIG_LBD=y +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -228,6 +243,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_PPC_NEED_DMA_SYNC_OPS=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y @@ -249,9 +265,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -296,6 +312,7 @@ CONFIG_PAGE_OFFSET=0xc0000000 CONFIG_KERNEL_START=0xc0000000 CONFIG_PHYSICAL_START=0x00000000 CONFIG_TASK_SIZE=0xc0000000 +CONFIG_CONSISTENT_SIZE=0x00200000 CONFIG_NET=y # @@ -357,6 +374,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -374,7 +392,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -479,6 +501,7 @@ CONFIG_MTD_PHYSMAP_OF=y # CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y +CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -514,7 +537,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y CONFIG_IDE=y @@ -591,10 +616,6 @@ CONFIG_BLK_DEV_SD=y # CONFIG_BLK_DEV_SR is not set # CONFIG_CHR_DEV_SG is not set # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -611,6 +632,7 @@ CONFIG_BLK_DEV_SD=y CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_CXGB3_ISCSI is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -619,6 +641,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -638,7 +661,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -721,7 +743,11 @@ CONFIG_SATA_MV=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set @@ -730,7 +756,6 @@ CONFIG_MACINTOSH_DRIVERS=y # CONFIG_MAC_EMUMOUSEBTN is not set # CONFIG_WINDFARM is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -797,6 +822,7 @@ CONFIG_8139TOO=y # CONFIG_SMSC9420 is not set # CONFIG_SUNDANCE is not set # CONFIG_TLAN is not set +# CONFIG_KS8842 is not set # CONFIG_VIA_RHINE is not set # CONFIG_SC92031 is not set # CONFIG_ATL2 is not set @@ -818,6 +844,7 @@ CONFIG_E1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_MV643XX_ETH=y # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set @@ -1007,13 +1034,17 @@ CONFIG_I2C_MV64XXX=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -1068,6 +1099,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -1102,23 +1134,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -# CONFIG_DAB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1163,6 +1181,7 @@ CONFIG_HID_BELKIN=y CONFIG_HID_CHERRY=y CONFIG_HID_CHICONY=y CONFIG_HID_CYPRESS=y +CONFIG_HID_DRAGONRISE=y # CONFIG_DRAGONRISE_FF is not set CONFIG_HID_EZKEY=y CONFIG_HID_KYE=y @@ -1180,9 +1199,14 @@ CONFIG_HID_PETALYNX=y CONFIG_HID_SAMSUNG=y CONFIG_HID_SONY=y CONFIG_HID_SUNPLUS=y +CONFIG_HID_GREENASIA=y # CONFIG_GREENASIA_FF is not set +CONFIG_HID_SMARTJOYPLUS=y +# CONFIG_SMARTJOYPLUS_FF is not set CONFIG_HID_TOPSEED=y +CONFIG_HID_THRUSTMASTER=y CONFIG_THRUSTMASTER_FF=y +CONFIG_HID_ZEROPLUS=y CONFIG_ZEROPLUS_FF=y CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y @@ -1207,6 +1231,7 @@ CONFIG_USB_MON=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y # CONFIG_USB_EHCI_ROOT_HUB_TT is not set # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1215,6 +1240,8 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=y +# CONFIG_USB_OHCI_HCD_PPC_OF_BE is not set +# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set # CONFIG_USB_OHCI_HCD_PPC_OF is not set # CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set # CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set @@ -1322,6 +1349,7 @@ CONFIG_RTC_DRV_MAX6900=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1349,6 +1377,10 @@ CONFIG_RTC_DRV_MAX6900=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1368,11 +1400,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1469,7 +1502,46 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set -# CONFIG_NLS is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +# CONFIG_NLS_CODEPAGE_437 is not set +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +# CONFIG_NLS_ISO8859_1 is not set +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set # CONFIG_DLM is not set # CONFIG_BINARY_PRINTF is not set @@ -1494,6 +1566,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1519,22 +1592,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_BOOTX_TEXT is not set diff --git a/arch/powerpc/configs/storcenter_defconfig b/arch/powerpc/configs/storcenter_defconfig index bd4a8d435c5..28384dc0100 100644 --- a/arch/powerpc/configs/storcenter_defconfig +++ b/arch/powerpc/configs/storcenter_defconfig @@ -1,25 +1,27 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc3 -# Wed May 13 17:22:04 2009 +# Linux kernel version: 2.6.31-rc4 +# Wed Jul 29 23:32:01 2009 # # CONFIG_PPC64 is not set # # Processor support # -CONFIG_6xx=y +CONFIG_PPC_BOOK3S_32=y # CONFIG_PPC_85xx is not set # CONFIG_PPC_8xx is not set # CONFIG_40x is not set # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_BOOK3S=y +CONFIG_6xx=y CONFIG_PPC_FPU=y # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set +CONFIG_PPC_HAVE_PMU_SUPPORT=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 @@ -30,15 +32,16 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y @@ -52,11 +55,13 @@ CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y +CONFIG_DTC=y # CONFIG_DEFAULT_UIMAGE is not set # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -101,7 +106,6 @@ CONFIG_ANON_INODES=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y # CONFIG_KALLSYMS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -114,9 +118,16 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -129,6 +140,10 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -141,7 +156,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -CONFIG_LBD=y +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -222,6 +237,7 @@ CONFIG_BINFMT_ELF=y # CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=y # CONFIG_IOMMU_HELPER is not set +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -242,9 +258,9 @@ CONFIG_MIGRATION=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_PPC_4K_PAGES=y # CONFIG_PPC_16K_PAGES is not set # CONFIG_PPC_64K_PAGES is not set @@ -347,6 +363,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -364,7 +381,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -501,7 +522,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y CONFIG_IDE=y @@ -579,10 +602,6 @@ CONFIG_BLK_DEV_SR=y # CONFIG_BLK_DEV_SR_VENDOR is not set # CONFIG_CHR_DEV_SG is not set # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -599,6 +618,7 @@ CONFIG_SCSI_SPI_ATTRS=y # CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -607,6 +627,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -626,7 +647,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_QLOGIC_1280 is not set @@ -660,14 +680,17 @@ CONFIG_MD_RAID6_PQ=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_DUMMY=m # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -695,8 +718,10 @@ CONFIG_R8169=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set # CONFIG_FSL_PQ_MDIO is not set # CONFIG_GIANFAR is not set +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -845,13 +870,17 @@ CONFIG_I2C_MPC=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -879,23 +908,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -# CONFIG_DAB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -937,6 +952,7 @@ CONFIG_USB_DEVICE_CLASS=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y # CONFIG_USB_EHCI_ROOT_HUB_TT is not set # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -946,6 +962,8 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=y +# CONFIG_USB_OHCI_HCD_PPC_OF_BE is not set +# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set # CONFIG_USB_OHCI_HCD_PPC_OF is not set # CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set # CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set @@ -1064,6 +1082,7 @@ CONFIG_RTC_DRV_DS1307=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1091,6 +1110,10 @@ CONFIG_RTC_DRV_DS1307=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1110,7 +1133,6 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y CONFIG_XFS_FS=m # CONFIG_XFS_QUOTA is not set # CONFIG_XFS_POSIX_ACL is not set @@ -1119,6 +1141,8 @@ CONFIG_XFS_FS=m # CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1273,6 +1297,7 @@ CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y +CONFIG_GENERIC_ATOMIC64=y # # Kernel hacking @@ -1298,22 +1323,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 # CONFIG_IRQSTACKS is not set # CONFIG_BOOTX_TEXT is not set -- GitLab From f294526279cda8934b0313ebd02184a16ba888c9 Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Sun, 19 Jul 2009 14:46:09 +0300 Subject: [PATCH 0559/1342] lguest: dereferencing freed mem in add_eventfd() "new" was freed and then dereferenced. Also the return value wasn't being used so I modified the caller as well. Compile tested only. Found by smatch (http://repo.or.cz/w/smatch.git). regards, dan carpenter Signed-off-by: Dan Carpenter Signed-off-by: Rusty Russell --- drivers/lguest/lguest_user.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/lguest/lguest_user.c b/drivers/lguest/lguest_user.c index 9f9a2953b38..407722a8e0c 100644 --- a/drivers/lguest/lguest_user.c +++ b/drivers/lguest/lguest_user.c @@ -52,8 +52,9 @@ static int add_eventfd(struct lguest *lg, unsigned long addr, int fd) new->map[new->num].addr = addr; new->map[new->num].event = eventfd_ctx_fdget(fd); if (IS_ERR(new->map[new->num].event)) { + int err = PTR_ERR(new->map[new->num].event); kfree(new); - return PTR_ERR(new->map[new->num].event); + return err; } new->num++; @@ -83,7 +84,7 @@ static int attach_eventfd(struct lguest *lg, const unsigned long __user *input) err = add_eventfd(lg, addr, fd); mutex_unlock(&lguest_lock); - return 0; + return err; } /*L:050 Sending an interrupt is done by writing LHREQ_IRQ and an interrupt -- GitLab From 8ef562d112c82ec539775698f8b63ac5ec1bd766 Mon Sep 17 00:00:00 2001 From: Rusty Russell Date: Thu, 30 Jul 2009 16:03:43 -0600 Subject: [PATCH 0560/1342] lguest: fix descriptor corruption in example launcher 1d589bb16b825b3a7b4edd34d997f1f1f953033d "Add serial number support for virtio_blk, V4a" extended 'struct virtio_blk_config' to 536 bytes. Lguest and S/390 both use an 8 bit value for the feature length, and this change broke them (if the code is naive). Signed-off-by: Rusty Russell Cc: John Cooper Cc: Christian Borntraeger --- Documentation/lguest/lguest.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/Documentation/lguest/lguest.c b/Documentation/lguest/lguest.c index 9ebcd6ef361..45d7d6dcae7 100644 --- a/Documentation/lguest/lguest.c +++ b/Documentation/lguest/lguest.c @@ -1105,6 +1105,9 @@ static void set_config(struct device *dev, unsigned len, const void *conf) /* Copy in the config information, and store the length. */ memcpy(device_config(dev), conf, len); dev->desc->config_len = len; + + /* Size must fit in config_len field (8 bits)! */ + assert(dev->desc->config_len == len); } /* This routine does all the creation and setup of a new device, including @@ -1515,7 +1518,8 @@ static void setup_block_file(const char *filename) add_feature(dev, VIRTIO_BLK_F_SEG_MAX); conf.seg_max = cpu_to_le32(VIRTQUEUE_NUM - 2); - set_config(dev, sizeof(conf), &conf); + /* Don't try to put whole struct: we have 8 bit limit. */ + set_config(dev, offsetof(struct virtio_blk_config, geometry), &conf); verbose("device %u: virtblock %llu sectors\n", ++devices.device_num, le64_to_cpu(conf.capacity)); -- GitLab From ff52c3fc7188855ede75d87b022271f0da309e5b Mon Sep 17 00:00:00 2001 From: "Michael S. Tsirkin" Date: Thu, 23 Jul 2009 14:57:37 +0300 Subject: [PATCH 0561/1342] virtio: fix memory leak on device removal Make vp_free_vectors do the reverse of vq_request_vectors. Signed-off-by: Michael S. Tsirkin Signed-off-by: Rusty Russell --- drivers/virtio/virtio_pci.c | 28 +++++++++++++++------------- 1 file changed, 15 insertions(+), 13 deletions(-) diff --git a/drivers/virtio/virtio_pci.c b/drivers/virtio/virtio_pci.c index bcec78ffc76..ca40517ef9c 100644 --- a/drivers/virtio/virtio_pci.c +++ b/drivers/virtio/virtio_pci.c @@ -258,7 +258,6 @@ static void vp_free_vectors(struct virtio_device *vdev) for (i = 0; i < vp_dev->msix_used_vectors; ++i) free_irq(vp_dev->msix_entries[i].vector, vp_dev); - vp_dev->msix_used_vectors = 0; if (vp_dev->msix_enabled) { /* Disable the vector used for configuration */ @@ -267,9 +266,16 @@ static void vp_free_vectors(struct virtio_device *vdev) /* Flush the write out to device */ ioread16(vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR); - vp_dev->msix_enabled = 0; pci_disable_msix(vp_dev->pci_dev); + vp_dev->msix_enabled = 0; + vp_dev->msix_vectors = 0; } + + vp_dev->msix_used_vectors = 0; + kfree(vp_dev->msix_names); + vp_dev->msix_names = NULL; + kfree(vp_dev->msix_entries); + vp_dev->msix_entries = NULL; } static int vp_enable_msix(struct pci_dev *dev, struct msix_entry *entries, @@ -297,11 +303,11 @@ static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs) vp_dev->msix_entries = kmalloc(nvectors * sizeof *vp_dev->msix_entries, GFP_KERNEL); if (!vp_dev->msix_entries) - goto error_entries; + goto error; vp_dev->msix_names = kmalloc(nvectors * sizeof *vp_dev->msix_names, GFP_KERNEL); if (!vp_dev->msix_names) - goto error_names; + goto error; for (i = 0; i < nvectors; ++i) vp_dev->msix_entries[i].entry = i; @@ -314,7 +320,7 @@ static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs) err = request_irq(vp_dev->pci_dev->irq, vp_interrupt, IRQF_SHARED, name, vp_dev); if (err) - goto error_irq; + goto error; vp_dev->intx_enabled = 1; } else { vp_dev->msix_vectors = err; @@ -328,7 +334,7 @@ static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs) vp_config_changed, 0, vp_dev->msix_names[v], vp_dev); if (err) - goto error_irq; + goto error; ++vp_dev->msix_used_vectors; iowrite16(v, vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR); @@ -336,7 +342,7 @@ static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs) v = ioread16(vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR); if (v == VIRTIO_MSI_NO_VECTOR) { err = -EBUSY; - goto error_irq; + goto error; } } @@ -349,16 +355,12 @@ static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs) vp_vring_interrupt, 0, vp_dev->msix_names[v], vp_dev); if (err) - goto error_irq; + goto error; ++vp_dev->msix_used_vectors; } return 0; -error_irq: +error: vp_free_vectors(vdev); - kfree(vp_dev->msix_names); -error_names: - kfree(vp_dev->msix_entries); -error_entries: return err; } -- GitLab From f6c82507030d61e15928d5cad946d3eac1c4a384 Mon Sep 17 00:00:00 2001 From: "Michael S. Tsirkin" Date: Sun, 26 Jul 2009 15:48:01 +0300 Subject: [PATCH 0562/1342] virtio: delete vq from list This makes delete vq the reverse of find vq. This is required to make it possible to retry find_vqs after a failure, otherwise the list gets corrupted. Signed-off-by: Michael S. Tsirkin Signed-off-by: Rusty Russell --- drivers/virtio/virtio_pci.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/drivers/virtio/virtio_pci.c b/drivers/virtio/virtio_pci.c index ca40517ef9c..a1cb1a1c652 100644 --- a/drivers/virtio/virtio_pci.c +++ b/drivers/virtio/virtio_pci.c @@ -464,7 +464,11 @@ static void vp_del_vq(struct virtqueue *vq) { struct virtio_pci_device *vp_dev = to_vp_device(vq->vdev); struct virtio_pci_vq_info *info = vq->priv; - unsigned long size; + unsigned long flags, size; + + spin_lock_irqsave(&vp_dev->lock, flags); + list_del(&info->node); + spin_unlock_irqrestore(&vp_dev->lock, flags); iowrite16(info->queue_index, vp_dev->ioaddr + VIRTIO_PCI_QUEUE_SEL); -- GitLab From e969fed542cae08cb11d666efac4f7c5d624d09f Mon Sep 17 00:00:00 2001 From: "Michael S. Tsirkin" Date: Sun, 26 Jul 2009 15:48:08 +0300 Subject: [PATCH 0563/1342] virtio: refactor find_vqs This refactors find_vqs, making it more readable and robust, and fixing two regressions from 2.6.30: - double free_irq causing BUG_ON on device removal - probe failure when vq can't be assigned to msi-x vector (reported on old host kernels) Tested-by: Amit Shah Signed-off-by: Michael S. Tsirkin Signed-off-by: Rusty Russell --- drivers/virtio/virtio_pci.c | 212 ++++++++++++++++++++---------------- 1 file changed, 119 insertions(+), 93 deletions(-) diff --git a/drivers/virtio/virtio_pci.c b/drivers/virtio/virtio_pci.c index a1cb1a1c652..248e00ec4dc 100644 --- a/drivers/virtio/virtio_pci.c +++ b/drivers/virtio/virtio_pci.c @@ -52,8 +52,10 @@ struct virtio_pci_device char (*msix_names)[256]; /* Number of available vectors */ unsigned msix_vectors; - /* Vectors allocated */ + /* Vectors allocated, excluding per-vq vectors if any */ unsigned msix_used_vectors; + /* Whether we have vector per vq */ + bool per_vq_vectors; }; /* Constants for MSI-X */ @@ -278,27 +280,24 @@ static void vp_free_vectors(struct virtio_device *vdev) vp_dev->msix_entries = NULL; } -static int vp_enable_msix(struct pci_dev *dev, struct msix_entry *entries, - int *options, int noptions) -{ - int i; - for (i = 0; i < noptions; ++i) - if (!pci_enable_msix(dev, entries, options[i])) - return options[i]; - return -EBUSY; -} - -static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs) +static int vp_request_vectors(struct virtio_device *vdev, int nvectors, + bool per_vq_vectors) { struct virtio_pci_device *vp_dev = to_vp_device(vdev); const char *name = dev_name(&vp_dev->vdev.dev); unsigned i, v; int err = -ENOMEM; - /* We want at most one vector per queue and one for config changes. - * Fallback to separate vectors for config and a shared for queues. - * Finally fall back to regular interrupts. */ - int options[] = { max_vqs + 1, 2 }; - int nvectors = max(options[0], options[1]); + + if (!nvectors) { + /* Can't allocate MSI-X vectors, use regular interrupt */ + vp_dev->msix_vectors = 0; + err = request_irq(vp_dev->pci_dev->irq, vp_interrupt, + IRQF_SHARED, name, vp_dev); + if (err) + return err; + vp_dev->intx_enabled = 1; + return 0; + } vp_dev->msix_entries = kmalloc(nvectors * sizeof *vp_dev->msix_entries, GFP_KERNEL); @@ -312,41 +311,34 @@ static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs) for (i = 0; i < nvectors; ++i) vp_dev->msix_entries[i].entry = i; - err = vp_enable_msix(vp_dev->pci_dev, vp_dev->msix_entries, - options, ARRAY_SIZE(options)); - if (err < 0) { - /* Can't allocate enough MSI-X vectors, use regular interrupt */ - vp_dev->msix_vectors = 0; - err = request_irq(vp_dev->pci_dev->irq, vp_interrupt, - IRQF_SHARED, name, vp_dev); - if (err) - goto error; - vp_dev->intx_enabled = 1; - } else { - vp_dev->msix_vectors = err; - vp_dev->msix_enabled = 1; - - /* Set the vector used for configuration */ - v = vp_dev->msix_used_vectors; - snprintf(vp_dev->msix_names[v], sizeof *vp_dev->msix_names, - "%s-config", name); - err = request_irq(vp_dev->msix_entries[v].vector, - vp_config_changed, 0, vp_dev->msix_names[v], - vp_dev); - if (err) - goto error; - ++vp_dev->msix_used_vectors; + err = pci_enable_msix(vp_dev->pci_dev, vp_dev->msix_entries, nvectors); + if (err > 0) + err = -ENOSPC; + if (err) + goto error; + vp_dev->msix_vectors = nvectors; + vp_dev->msix_enabled = 1; + + /* Set the vector used for configuration */ + v = vp_dev->msix_used_vectors; + snprintf(vp_dev->msix_names[v], sizeof *vp_dev->msix_names, + "%s-config", name); + err = request_irq(vp_dev->msix_entries[v].vector, + vp_config_changed, 0, vp_dev->msix_names[v], + vp_dev); + if (err) + goto error; + ++vp_dev->msix_used_vectors; - iowrite16(v, vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR); - /* Verify we had enough resources to assign the vector */ - v = ioread16(vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR); - if (v == VIRTIO_MSI_NO_VECTOR) { - err = -EBUSY; - goto error; - } + iowrite16(v, vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR); + /* Verify we had enough resources to assign the vector */ + v = ioread16(vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR); + if (v == VIRTIO_MSI_NO_VECTOR) { + err = -EBUSY; + goto error; } - if (vp_dev->msix_vectors && vp_dev->msix_vectors != max_vqs + 1) { + if (!per_vq_vectors) { /* Shared vector for all VQs */ v = vp_dev->msix_used_vectors; snprintf(vp_dev->msix_names[v], sizeof *vp_dev->msix_names, @@ -366,13 +358,14 @@ error: static struct virtqueue *vp_find_vq(struct virtio_device *vdev, unsigned index, void (*callback)(struct virtqueue *vq), - const char *name) + const char *name, + u16 vector) { struct virtio_pci_device *vp_dev = to_vp_device(vdev); struct virtio_pci_vq_info *info; struct virtqueue *vq; unsigned long flags, size; - u16 num, vector; + u16 num; int err; /* Select the queue we're interested in */ @@ -391,7 +384,7 @@ static struct virtqueue *vp_find_vq(struct virtio_device *vdev, unsigned index, info->queue_index = index; info->num = num; - info->vector = VIRTIO_MSI_NO_VECTOR; + info->vector = vector; size = PAGE_ALIGN(vring_size(num, VIRTIO_PCI_VRING_ALIGN)); info->queue = alloc_pages_exact(size, GFP_KERNEL|__GFP_ZERO); @@ -415,22 +408,7 @@ static struct virtqueue *vp_find_vq(struct virtio_device *vdev, unsigned index, vq->priv = info; info->vq = vq; - /* allocate per-vq vector if available and necessary */ - if (callback && vp_dev->msix_used_vectors < vp_dev->msix_vectors) { - vector = vp_dev->msix_used_vectors; - snprintf(vp_dev->msix_names[vector], sizeof *vp_dev->msix_names, - "%s-%s", dev_name(&vp_dev->vdev.dev), name); - err = request_irq(vp_dev->msix_entries[vector].vector, - vring_interrupt, 0, - vp_dev->msix_names[vector], vq); - if (err) - goto out_request_irq; - info->vector = vector; - ++vp_dev->msix_used_vectors; - } else - vector = VP_MSIX_VQ_VECTOR; - - if (callback && vp_dev->msix_enabled) { + if (vector != VIRTIO_MSI_NO_VECTOR) { iowrite16(vector, vp_dev->ioaddr + VIRTIO_MSI_QUEUE_VECTOR); vector = ioread16(vp_dev->ioaddr + VIRTIO_MSI_QUEUE_VECTOR); if (vector == VIRTIO_MSI_NO_VECTOR) { @@ -446,11 +424,6 @@ static struct virtqueue *vp_find_vq(struct virtio_device *vdev, unsigned index, return vq; out_assign: - if (info->vector != VIRTIO_MSI_NO_VECTOR) { - free_irq(vp_dev->msix_entries[info->vector].vector, vq); - --vp_dev->msix_used_vectors; - } -out_request_irq: vring_del_virtqueue(vq); out_activate_queue: iowrite32(0, vp_dev->ioaddr + VIRTIO_PCI_QUEUE_PFN); @@ -472,9 +445,6 @@ static void vp_del_vq(struct virtqueue *vq) iowrite16(info->queue_index, vp_dev->ioaddr + VIRTIO_PCI_QUEUE_SEL); - if (info->vector != VIRTIO_MSI_NO_VECTOR) - free_irq(vp_dev->msix_entries[info->vector].vector, vq); - if (vp_dev->msix_enabled) { iowrite16(VIRTIO_MSI_NO_VECTOR, vp_dev->ioaddr + VIRTIO_MSI_QUEUE_VECTOR); @@ -495,36 +465,62 @@ static void vp_del_vq(struct virtqueue *vq) /* the config->del_vqs() implementation */ static void vp_del_vqs(struct virtio_device *vdev) { + struct virtio_pci_device *vp_dev = to_vp_device(vdev); struct virtqueue *vq, *n; + struct virtio_pci_vq_info *info; - list_for_each_entry_safe(vq, n, &vdev->vqs, list) + list_for_each_entry_safe(vq, n, &vdev->vqs, list) { + info = vq->priv; + if (vp_dev->per_vq_vectors) + free_irq(vp_dev->msix_entries[info->vector].vector, vq); vp_del_vq(vq); + } + vp_dev->per_vq_vectors = false; vp_free_vectors(vdev); } -/* the config->find_vqs() implementation */ -static int vp_find_vqs(struct virtio_device *vdev, unsigned nvqs, - struct virtqueue *vqs[], - vq_callback_t *callbacks[], - const char *names[]) +static int vp_try_to_find_vqs(struct virtio_device *vdev, unsigned nvqs, + struct virtqueue *vqs[], + vq_callback_t *callbacks[], + const char *names[], + int nvectors, + bool per_vq_vectors) { - int vectors = 0; - int i, err; - - /* How many vectors would we like? */ - for (i = 0; i < nvqs; ++i) - if (callbacks[i]) - ++vectors; + struct virtio_pci_device *vp_dev = to_vp_device(vdev); + u16 vector; + int i, err, allocated_vectors; - err = vp_request_vectors(vdev, vectors); + err = vp_request_vectors(vdev, nvectors, per_vq_vectors); if (err) goto error_request; + vp_dev->per_vq_vectors = per_vq_vectors; + allocated_vectors = vp_dev->msix_used_vectors; for (i = 0; i < nvqs; ++i) { - vqs[i] = vp_find_vq(vdev, i, callbacks[i], names[i]); - if (IS_ERR(vqs[i])) + if (!callbacks[i] || !vp_dev->msix_enabled) + vector = VIRTIO_MSI_NO_VECTOR; + else if (vp_dev->per_vq_vectors) + vector = allocated_vectors++; + else + vector = VP_MSIX_VQ_VECTOR; + vqs[i] = vp_find_vq(vdev, i, callbacks[i], names[i], vector); + if (IS_ERR(vqs[i])) { + err = PTR_ERR(vqs[i]); goto error_find; + } + /* allocate per-vq irq if available and necessary */ + if (vp_dev->per_vq_vectors && vector != VIRTIO_MSI_NO_VECTOR) { + snprintf(vp_dev->msix_names[vector], sizeof *vp_dev->msix_names, + "%s-%s", dev_name(&vp_dev->vdev.dev), names[i]); + err = request_irq(vp_dev->msix_entries[vector].vector, + vring_interrupt, 0, + vp_dev->msix_names[vector], vqs[i]); + if (err) { + vp_del_vq(vqs[i]); + goto error_find; + } + } } return 0; @@ -532,7 +528,37 @@ error_find: vp_del_vqs(vdev); error_request: - return PTR_ERR(vqs[i]); + return err; +} + +/* the config->find_vqs() implementation */ +static int vp_find_vqs(struct virtio_device *vdev, unsigned nvqs, + struct virtqueue *vqs[], + vq_callback_t *callbacks[], + const char *names[]) +{ + int vectors = 0; + int i, uninitialized_var(err); + + /* How many vectors would we like? */ + for (i = 0; i < nvqs; ++i) + if (callbacks[i]) + ++vectors; + + /* We want at most one vector per queue and one for config changes. */ + err = vp_try_to_find_vqs(vdev, nvqs, vqs, callbacks, names, + vectors + 1, true); + if (!err) + return 0; + /* Fallback to separate vectors for config and a shared for queues. */ + err = vp_try_to_find_vqs(vdev, nvqs, vqs, callbacks, names, + 2, false); + if (!err) + return 0; + /* Finally fall back to regular interrupts. */ + err = vp_try_to_find_vqs(vdev, nvqs, vqs, callbacks, names, + 0, false); + return err; } static struct virtio_config_ops virtio_pci_config_ops = { -- GitLab From 2e04ef76916d1e29a077ea9d0f2003c8fd86724d Mon Sep 17 00:00:00 2001 From: Rusty Russell Date: Thu, 30 Jul 2009 16:03:45 -0600 Subject: [PATCH 0564/1342] lguest: fix comment style I don't really notice it (except to begrudge the extra vertical space), but Ingo does. And he pointed out that one excuse of lguest is as a teaching tool, it should set a good example. Signed-off-by: Rusty Russell Cc: Ingo Molnar --- Documentation/lguest/lguest.c | 540 +++++++++++++++++--------- arch/x86/include/asm/lguest.h | 3 +- arch/x86/include/asm/lguest_hcall.h | 10 +- arch/x86/lguest/boot.c | 428 +++++++++++++------- arch/x86/lguest/i386_head.S | 110 ++++-- drivers/lguest/core.c | 114 ++++-- drivers/lguest/hypercalls.c | 141 ++++--- drivers/lguest/interrupts_and_traps.c | 288 +++++++++----- drivers/lguest/lg.h | 23 +- drivers/lguest/lguest_device.c | 150 ++++--- drivers/lguest/lguest_user.c | 137 ++++--- drivers/lguest/page_tables.c | 427 +++++++++++++------- drivers/lguest/segments.c | 106 +++-- drivers/lguest/x86/core.c | 372 ++++++++++++------ drivers/lguest/x86/switcher_32.S | 18 +- include/linux/lguest.h | 36 +- include/linux/lguest_launcher.h | 18 +- 17 files changed, 1906 insertions(+), 1015 deletions(-) diff --git a/Documentation/lguest/lguest.c b/Documentation/lguest/lguest.c index 45d7d6dcae7..aa66a52b73e 100644 --- a/Documentation/lguest/lguest.c +++ b/Documentation/lguest/lguest.c @@ -1,7 +1,9 @@ -/*P:100 This is the Launcher code, a simple program which lays out the - * "physical" memory for the new Guest by mapping the kernel image and - * the virtual devices, then opens /dev/lguest to tell the kernel - * about the Guest and control it. :*/ +/*P:100 + * This is the Launcher code, a simple program which lays out the "physical" + * memory for the new Guest by mapping the kernel image and the virtual + * devices, then opens /dev/lguest to tell the kernel about the Guest and + * control it. +:*/ #define _LARGEFILE64_SOURCE #define _GNU_SOURCE #include @@ -46,13 +48,15 @@ #include "linux/virtio_rng.h" #include "linux/virtio_ring.h" #include "asm/bootparam.h" -/*L:110 We can ignore the 39 include files we need for this program, but I do - * want to draw attention to the use of kernel-style types. +/*L:110 + * We can ignore the 39 include files we need for this program, but I do want + * to draw attention to the use of kernel-style types. * * As Linus said, "C is a Spartan language, and so should your naming be." I * like these abbreviations, so we define them here. Note that u64 is always * unsigned long long, which works on all Linux systems: this means that we can - * use %llu in printf for any u64. */ + * use %llu in printf for any u64. + */ typedef unsigned long long u64; typedef uint32_t u32; typedef uint16_t u16; @@ -69,8 +73,10 @@ typedef uint8_t u8; /* This will occupy 3 pages: it must be a power of 2. */ #define VIRTQUEUE_NUM 256 -/*L:120 verbose is both a global flag and a macro. The C preprocessor allows - * this, and although I wouldn't recommend it, it works quite nicely here. */ +/*L:120 + * verbose is both a global flag and a macro. The C preprocessor allows + * this, and although I wouldn't recommend it, it works quite nicely here. + */ static bool verbose; #define verbose(args...) \ do { if (verbose) printf(args); } while(0) @@ -100,8 +106,7 @@ struct device_list /* A single linked list of devices. */ struct device *dev; - /* And a pointer to the last device for easy append and also for - * configuration appending. */ + /* And a pointer to the last device for easy append. */ struct device *lastdev; }; @@ -168,20 +173,24 @@ static char **main_args; /* The original tty settings to restore on exit. */ static struct termios orig_term; -/* We have to be careful with barriers: our devices are all run in separate +/* + * We have to be careful with barriers: our devices are all run in separate * threads and so we need to make sure that changes visible to the Guest happen - * in precise order. */ + * in precise order. + */ #define wmb() __asm__ __volatile__("" : : : "memory") #define mb() __asm__ __volatile__("" : : : "memory") -/* Convert an iovec element to the given type. +/* + * Convert an iovec element to the given type. * * This is a fairly ugly trick: we need to know the size of the type and * alignment requirement to check the pointer is kosher. It's also nice to * have the name of the type in case we report failure. * * Typing those three things all the time is cumbersome and error prone, so we - * have a macro which sets them all up and passes to the real function. */ + * have a macro which sets them all up and passes to the real function. + */ #define convert(iov, type) \ ((type *)_convert((iov), sizeof(type), __alignof__(type), #type)) @@ -198,8 +207,10 @@ static void *_convert(struct iovec *iov, size_t size, size_t align, /* Wrapper for the last available index. Makes it easier to change. */ #define lg_last_avail(vq) ((vq)->last_avail_idx) -/* The virtio configuration space is defined to be little-endian. x86 is - * little-endian too, but it's nice to be explicit so we have these helpers. */ +/* + * The virtio configuration space is defined to be little-endian. x86 is + * little-endian too, but it's nice to be explicit so we have these helpers. + */ #define cpu_to_le16(v16) (v16) #define cpu_to_le32(v32) (v32) #define cpu_to_le64(v64) (v64) @@ -241,11 +252,12 @@ static u8 *get_feature_bits(struct device *dev) + dev->num_vq * sizeof(struct lguest_vqconfig); } -/*L:100 The Launcher code itself takes us out into userspace, that scary place - * where pointers run wild and free! Unfortunately, like most userspace - * programs, it's quite boring (which is why everyone likes to hack on the - * kernel!). Perhaps if you make up an Lguest Drinking Game at this point, it - * will get you through this section. Or, maybe not. +/*L:100 + * The Launcher code itself takes us out into userspace, that scary place where + * pointers run wild and free! Unfortunately, like most userspace programs, + * it's quite boring (which is why everyone likes to hack on the kernel!). + * Perhaps if you make up an Lguest Drinking Game at this point, it will get + * you through this section. Or, maybe not. * * The Launcher sets up a big chunk of memory to be the Guest's "physical" * memory and stores it in "guest_base". In other words, Guest physical == @@ -253,7 +265,8 @@ static u8 *get_feature_bits(struct device *dev) * * This can be tough to get your head around, but usually it just means that we * use these trivial conversion functions when the Guest gives us it's - * "physical" addresses: */ + * "physical" addresses: + */ static void *from_guest_phys(unsigned long addr) { return guest_base + addr; @@ -268,7 +281,8 @@ static unsigned long to_guest_phys(const void *addr) * Loading the Kernel. * * We start with couple of simple helper routines. open_or_die() avoids - * error-checking code cluttering the callers: */ + * error-checking code cluttering the callers: + */ static int open_or_die(const char *name, int flags) { int fd = open(name, flags); @@ -283,8 +297,10 @@ static void *map_zeroed_pages(unsigned int num) int fd = open_or_die("/dev/zero", O_RDONLY); void *addr; - /* We use a private mapping (ie. if we write to the page, it will be - * copied). */ + /* + * We use a private mapping (ie. if we write to the page, it will be + * copied). + */ addr = mmap(NULL, getpagesize() * num, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE, fd, 0); if (addr == MAP_FAILED) @@ -305,20 +321,24 @@ static void *get_pages(unsigned int num) return addr; } -/* This routine is used to load the kernel or initrd. It tries mmap, but if +/* + * This routine is used to load the kernel or initrd. It tries mmap, but if * that fails (Plan 9's kernel file isn't nicely aligned on page boundaries), - * it falls back to reading the memory in. */ + * it falls back to reading the memory in. + */ static void map_at(int fd, void *addr, unsigned long offset, unsigned long len) { ssize_t r; - /* We map writable even though for some segments are marked read-only. + /* + * We map writable even though for some segments are marked read-only. * The kernel really wants to be writable: it patches its own * instructions. * * MAP_PRIVATE means that the page won't be copied until a write is * done to it. This allows us to share untouched memory between - * Guests. */ + * Guests. + */ if (mmap(addr, len, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_FIXED|MAP_PRIVATE, fd, offset) != MAP_FAILED) return; @@ -329,7 +349,8 @@ static void map_at(int fd, void *addr, unsigned long offset, unsigned long len) err(1, "Reading offset %lu len %lu gave %zi", offset, len, r); } -/* This routine takes an open vmlinux image, which is in ELF, and maps it into +/* + * This routine takes an open vmlinux image, which is in ELF, and maps it into * the Guest memory. ELF = Embedded Linking Format, which is the format used * by all modern binaries on Linux including the kernel. * @@ -337,23 +358,28 @@ static void map_at(int fd, void *addr, unsigned long offset, unsigned long len) * address. We use the physical address; the Guest will map itself to the * virtual address. * - * We return the starting address. */ + * We return the starting address. + */ static unsigned long map_elf(int elf_fd, const Elf32_Ehdr *ehdr) { Elf32_Phdr phdr[ehdr->e_phnum]; unsigned int i; - /* Sanity checks on the main ELF header: an x86 executable with a - * reasonable number of correctly-sized program headers. */ + /* + * Sanity checks on the main ELF header: an x86 executable with a + * reasonable number of correctly-sized program headers. + */ if (ehdr->e_type != ET_EXEC || ehdr->e_machine != EM_386 || ehdr->e_phentsize != sizeof(Elf32_Phdr) || ehdr->e_phnum < 1 || ehdr->e_phnum > 65536U/sizeof(Elf32_Phdr)) errx(1, "Malformed elf header"); - /* An ELF executable contains an ELF header and a number of "program" + /* + * An ELF executable contains an ELF header and a number of "program" * headers which indicate which parts ("segments") of the program to - * load where. */ + * load where. + */ /* We read in all the program headers at once: */ if (lseek(elf_fd, ehdr->e_phoff, SEEK_SET) < 0) @@ -361,8 +387,10 @@ static unsigned long map_elf(int elf_fd, const Elf32_Ehdr *ehdr) if (read(elf_fd, phdr, sizeof(phdr)) != sizeof(phdr)) err(1, "Reading program headers"); - /* Try all the headers: there are usually only three. A read-only one, - * a read-write one, and a "note" section which we don't load. */ + /* + * Try all the headers: there are usually only three. A read-only one, + * a read-write one, and a "note" section which we don't load. + */ for (i = 0; i < ehdr->e_phnum; i++) { /* If this isn't a loadable segment, we ignore it */ if (phdr[i].p_type != PT_LOAD) @@ -380,13 +408,15 @@ static unsigned long map_elf(int elf_fd, const Elf32_Ehdr *ehdr) return ehdr->e_entry; } -/*L:150 A bzImage, unlike an ELF file, is not meant to be loaded. You're - * supposed to jump into it and it will unpack itself. We used to have to - * perform some hairy magic because the unpacking code scared me. +/*L:150 + * A bzImage, unlike an ELF file, is not meant to be loaded. You're supposed + * to jump into it and it will unpack itself. We used to have to perform some + * hairy magic because the unpacking code scared me. * * Fortunately, Jeremy Fitzhardinge convinced me it wasn't that hard and wrote * a small patch to jump over the tricky bits in the Guest, so now we just read - * the funky header so we know where in the file to load, and away we go! */ + * the funky header so we know where in the file to load, and away we go! + */ static unsigned long load_bzimage(int fd) { struct boot_params boot; @@ -394,8 +424,10 @@ static unsigned long load_bzimage(int fd) /* Modern bzImages get loaded at 1M. */ void *p = from_guest_phys(0x100000); - /* Go back to the start of the file and read the header. It should be - * a Linux boot header (see Documentation/x86/i386/boot.txt) */ + /* + * Go back to the start of the file and read the header. It should be + * a Linux boot header (see Documentation/x86/i386/boot.txt) + */ lseek(fd, 0, SEEK_SET); read(fd, &boot, sizeof(boot)); @@ -414,9 +446,11 @@ static unsigned long load_bzimage(int fd) return boot.hdr.code32_start; } -/*L:140 Loading the kernel is easy when it's a "vmlinux", but most kernels +/*L:140 + * Loading the kernel is easy when it's a "vmlinux", but most kernels * come wrapped up in the self-decompressing "bzImage" format. With a little - * work, we can load those, too. */ + * work, we can load those, too. + */ static unsigned long load_kernel(int fd) { Elf32_Ehdr hdr; @@ -433,24 +467,28 @@ static unsigned long load_kernel(int fd) return load_bzimage(fd); } -/* This is a trivial little helper to align pages. Andi Kleen hated it because +/* + * This is a trivial little helper to align pages. Andi Kleen hated it because * it calls getpagesize() twice: "it's dumb code." * * Kernel guys get really het up about optimization, even when it's not - * necessary. I leave this code as a reaction against that. */ + * necessary. I leave this code as a reaction against that. + */ static inline unsigned long page_align(unsigned long addr) { /* Add upwards and truncate downwards. */ return ((addr + getpagesize()-1) & ~(getpagesize()-1)); } -/*L:180 An "initial ram disk" is a disk image loaded into memory along with - * the kernel which the kernel can use to boot from without needing any - * drivers. Most distributions now use this as standard: the initrd contains - * the code to load the appropriate driver modules for the current machine. +/*L:180 + * An "initial ram disk" is a disk image loaded into memory along with the + * kernel which the kernel can use to boot from without needing any drivers. + * Most distributions now use this as standard: the initrd contains the code to + * load the appropriate driver modules for the current machine. * * Importantly, James Morris works for RedHat, and Fedora uses initrds for its - * kernels. He sent me this (and tells me when I break it). */ + * kernels. He sent me this (and tells me when I break it). + */ static unsigned long load_initrd(const char *name, unsigned long mem) { int ifd; @@ -462,12 +500,16 @@ static unsigned long load_initrd(const char *name, unsigned long mem) if (fstat(ifd, &st) < 0) err(1, "fstat() on initrd '%s'", name); - /* We map the initrd at the top of memory, but mmap wants it to be - * page-aligned, so we round the size up for that. */ + /* + * We map the initrd at the top of memory, but mmap wants it to be + * page-aligned, so we round the size up for that. + */ len = page_align(st.st_size); map_at(ifd, from_guest_phys(mem - len), 0, st.st_size); - /* Once a file is mapped, you can close the file descriptor. It's a - * little odd, but quite useful. */ + /* + * Once a file is mapped, you can close the file descriptor. It's a + * little odd, but quite useful. + */ close(ifd); verbose("mapped initrd %s size=%lu @ %p\n", name, len, (void*)mem-len); @@ -476,8 +518,10 @@ static unsigned long load_initrd(const char *name, unsigned long mem) } /*:*/ -/* Simple routine to roll all the commandline arguments together with spaces - * between them. */ +/* + * Simple routine to roll all the commandline arguments together with spaces + * between them. + */ static void concat(char *dst, char *args[]) { unsigned int i, len = 0; @@ -494,10 +538,12 @@ static void concat(char *dst, char *args[]) dst[len] = '\0'; } -/*L:185 This is where we actually tell the kernel to initialize the Guest. We +/*L:185 + * This is where we actually tell the kernel to initialize the Guest. We * saw the arguments it expects when we looked at initialize() in lguest_user.c: * the base of Guest "physical" memory, the top physical page to allow and the - * entry point for the Guest. */ + * entry point for the Guest. + */ static void tell_kernel(unsigned long start) { unsigned long args[] = { LHREQ_INITIALIZE, @@ -522,20 +568,26 @@ static void tell_kernel(unsigned long start) static void *_check_pointer(unsigned long addr, unsigned int size, unsigned int line) { - /* We have to separately check addr and addr+size, because size could - * be huge and addr + size might wrap around. */ + /* + * We have to separately check addr and addr+size, because size could + * be huge and addr + size might wrap around. + */ if (addr >= guest_limit || addr + size >= guest_limit) errx(1, "%s:%i: Invalid address %#lx", __FILE__, line, addr); - /* We return a pointer for the caller's convenience, now we know it's - * safe to use. */ + /* + * We return a pointer for the caller's convenience, now we know it's + * safe to use. + */ return from_guest_phys(addr); } /* A macro which transparently hands the line number to the real function. */ #define check_pointer(addr,size) _check_pointer(addr, size, __LINE__) -/* Each buffer in the virtqueues is actually a chain of descriptors. This +/* + * Each buffer in the virtqueues is actually a chain of descriptors. This * function returns the next descriptor in the chain, or vq->vring.num if we're - * at the end. */ + * at the end. + */ static unsigned next_desc(struct vring_desc *desc, unsigned int i, unsigned int max) { @@ -576,12 +628,14 @@ static void trigger_irq(struct virtqueue *vq) err(1, "Triggering irq %i", vq->config.irq); } -/* This looks in the virtqueue and for the first available buffer, and converts +/* + * This looks in the virtqueue and for the first available buffer, and converts * it to an iovec for convenient access. Since descriptors consist of some * number of output then some number of input descriptors, it's actually two * iovecs, but we pack them into one and note how many of each there were. * - * This function returns the descriptor number found. */ + * This function returns the descriptor number found. + */ static unsigned wait_for_vq_desc(struct virtqueue *vq, struct iovec iov[], unsigned int *out_num, unsigned int *in_num) @@ -599,8 +653,10 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq, /* OK, now we need to know about added descriptors. */ vq->vring.used->flags &= ~VRING_USED_F_NO_NOTIFY; - /* They could have slipped one in as we were doing that: make - * sure it's written, then check again. */ + /* + * They could have slipped one in as we were doing that: make + * sure it's written, then check again. + */ mb(); if (last_avail != vq->vring.avail->idx) { vq->vring.used->flags |= VRING_USED_F_NO_NOTIFY; @@ -620,8 +676,10 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq, errx(1, "Guest moved used index from %u to %u", last_avail, vq->vring.avail->idx); - /* Grab the next descriptor number they're advertising, and increment - * the index we've seen. */ + /* + * Grab the next descriptor number they're advertising, and increment + * the index we've seen. + */ head = vq->vring.avail->ring[last_avail % vq->vring.num]; lg_last_avail(vq)++; @@ -636,8 +694,10 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq, desc = vq->vring.desc; i = head; - /* If this is an indirect entry, then this buffer contains a descriptor - * table which we handle as if it's any normal descriptor chain. */ + /* + * If this is an indirect entry, then this buffer contains a descriptor + * table which we handle as if it's any normal descriptor chain. + */ if (desc[i].flags & VRING_DESC_F_INDIRECT) { if (desc[i].len % sizeof(struct vring_desc)) errx(1, "Invalid size for indirect buffer table"); @@ -656,8 +716,10 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq, if (desc[i].flags & VRING_DESC_F_WRITE) (*in_num)++; else { - /* If it's an output descriptor, they're all supposed - * to come before any input descriptors. */ + /* + * If it's an output descriptor, they're all supposed + * to come before any input descriptors. + */ if (*in_num) errx(1, "Descriptor has out after in"); (*out_num)++; @@ -671,14 +733,18 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq, return head; } -/* After we've used one of their buffers, we tell them about it. We'll then - * want to send them an interrupt, using trigger_irq(). */ +/* + * After we've used one of their buffers, we tell them about it. We'll then + * want to send them an interrupt, using trigger_irq(). + */ static void add_used(struct virtqueue *vq, unsigned int head, int len) { struct vring_used_elem *used; - /* The virtqueue contains a ring of used buffers. Get a pointer to the - * next entry in that used ring. */ + /* + * The virtqueue contains a ring of used buffers. Get a pointer to the + * next entry in that used ring. + */ used = &vq->vring.used->ring[vq->vring.used->idx % vq->vring.num]; used->id = head; used->len = len; @@ -698,7 +764,8 @@ static void add_used_and_trigger(struct virtqueue *vq, unsigned head, int len) /* * The Console * - * We associate some data with the console for our exit hack. */ + * We associate some data with the console for our exit hack. + */ struct console_abort { /* How many times have they hit ^C? */ @@ -725,20 +792,24 @@ static void console_input(struct virtqueue *vq) if (len <= 0) { /* Ran out of input? */ warnx("Failed to get console input, ignoring console."); - /* For simplicity, dying threads kill the whole Launcher. So - * just nap here. */ + /* + * For simplicity, dying threads kill the whole Launcher. So + * just nap here. + */ for (;;) pause(); } add_used_and_trigger(vq, head, len); - /* Three ^C within one second? Exit. + /* + * Three ^C within one second? Exit. * * This is such a hack, but works surprisingly well. Each ^C has to * be in a buffer by itself, so they can't be too fast. But we check * that we get three within about a second, so they can't be too - * slow. */ + * slow. + */ if (len != 1 || ((char *)iov[0].iov_base)[0] != 3) { abort->count = 0; return; @@ -809,8 +880,7 @@ static bool will_block(int fd) return select(fd+1, &fdset, NULL, NULL, &zero) != 1; } -/* This is where we handle packets coming in from the tun device to our - * Guest. */ +/* This handles packets coming in from the tun device to our Guest. */ static void net_input(struct virtqueue *vq) { int len; @@ -842,8 +912,10 @@ static int do_thread(void *_vq) return 0; } -/* When a child dies, we kill our entire process group with SIGTERM. This - * also has the side effect that the shell restores the console for us! */ +/* + * When a child dies, we kill our entire process group with SIGTERM. This + * also has the side effect that the shell restores the console for us! + */ static void kill_launcher(int signal) { kill(0, SIGTERM); @@ -880,9 +952,10 @@ static void reset_device(struct device *dev) static void create_thread(struct virtqueue *vq) { - /* Create stack for thread and run it. Since stack grows - * upwards, we point the stack pointer to the end of this - * region. */ + /* + * Create stack for thread and run it. Since the stack grows upwards, + * we point the stack pointer to the end of this region. + */ char *stack = malloc(32768); unsigned long args[] = { LHREQ_EVENTFD, vq->config.pfn*getpagesize(), 0 }; @@ -981,8 +1054,11 @@ static void handle_output(unsigned long addr) } } - /* Early console write is done using notify on a nul-terminated string - * in Guest memory. */ + /* + * Early console write is done using notify on a nul-terminated string + * in Guest memory. It's also great for hacking debugging messages + * into a Guest. + */ if (addr >= guest_limit) errx(1, "Bad NOTIFY %#lx", addr); @@ -998,10 +1074,12 @@ static void handle_output(unsigned long addr) * routines to allocate and manage them. */ -/* The layout of the device page is a "struct lguest_device_desc" followed by a +/* + * The layout of the device page is a "struct lguest_device_desc" followed by a * number of virtqueue descriptors, then two sets of feature bits, then an * array of configuration bytes. This routine returns the configuration - * pointer. */ + * pointer. + */ static u8 *device_config(const struct device *dev) { return (void *)(dev->desc + 1) @@ -1009,9 +1087,11 @@ static u8 *device_config(const struct device *dev) + dev->feature_len * 2; } -/* This routine allocates a new "struct lguest_device_desc" from descriptor +/* + * This routine allocates a new "struct lguest_device_desc" from descriptor * table page just above the Guest's normal memory. It returns a pointer to - * that descriptor. */ + * that descriptor. + */ static struct lguest_device_desc *new_dev_desc(u16 type) { struct lguest_device_desc d = { .type = type }; @@ -1032,8 +1112,10 @@ static struct lguest_device_desc *new_dev_desc(u16 type) return memcpy(p, &d, sizeof(d)); } -/* Each device descriptor is followed by the description of its virtqueues. We - * specify how many descriptors the virtqueue is to have. */ +/* + * Each device descriptor is followed by the description of its virtqueues. We + * specify how many descriptors the virtqueue is to have. + */ static void add_virtqueue(struct device *dev, unsigned int num_descs, void (*service)(struct virtqueue *)) { @@ -1061,10 +1143,12 @@ static void add_virtqueue(struct device *dev, unsigned int num_descs, /* Initialize the vring. */ vring_init(&vq->vring, num_descs, p, LGUEST_VRING_ALIGN); - /* Append virtqueue to this device's descriptor. We use + /* + * Append virtqueue to this device's descriptor. We use * device_config() to get the end of the device's current virtqueues; * we check that we haven't added any config or feature information - * yet, otherwise we'd be overwriting them. */ + * yet, otherwise we'd be overwriting them. + */ assert(dev->desc->config_len == 0 && dev->desc->feature_len == 0); memcpy(device_config(dev), &vq->config, sizeof(vq->config)); dev->num_vq++; @@ -1072,14 +1156,18 @@ static void add_virtqueue(struct device *dev, unsigned int num_descs, verbose("Virtqueue page %#lx\n", to_guest_phys(p)); - /* Add to tail of list, so dev->vq is first vq, dev->vq->next is - * second. */ + /* + * Add to tail of list, so dev->vq is first vq, dev->vq->next is + * second. + */ for (i = &dev->vq; *i; i = &(*i)->next); *i = vq; } -/* The first half of the feature bitmask is for us to advertise features. The - * second half is for the Guest to accept features. */ +/* + * The first half of the feature bitmask is for us to advertise features. The + * second half is for the Guest to accept features. + */ static void add_feature(struct device *dev, unsigned bit) { u8 *features = get_feature_bits(dev); @@ -1093,9 +1181,11 @@ static void add_feature(struct device *dev, unsigned bit) features[bit / CHAR_BIT] |= (1 << (bit % CHAR_BIT)); } -/* This routine sets the configuration fields for an existing device's +/* + * This routine sets the configuration fields for an existing device's * descriptor. It only works for the last device, but that's OK because that's - * how we use it. */ + * how we use it. + */ static void set_config(struct device *dev, unsigned len, const void *conf) { /* Check we haven't overflowed our single page. */ @@ -1110,10 +1200,12 @@ static void set_config(struct device *dev, unsigned len, const void *conf) assert(dev->desc->config_len == len); } -/* This routine does all the creation and setup of a new device, including +/* + * This routine does all the creation and setup of a new device, including * calling new_dev_desc() to allocate the descriptor and device memory. * - * See what I mean about userspace being boring? */ + * See what I mean about userspace being boring? + */ static struct device *new_device(const char *name, u16 type) { struct device *dev = malloc(sizeof(*dev)); @@ -1126,10 +1218,12 @@ static struct device *new_device(const char *name, u16 type) dev->num_vq = 0; dev->running = false; - /* Append to device list. Prepending to a single-linked list is + /* + * Append to device list. Prepending to a single-linked list is * easier, but the user expects the devices to be arranged on the bus * in command-line order. The first network device on the command line - * is eth0, the first block device /dev/vda, etc. */ + * is eth0, the first block device /dev/vda, etc. + */ if (devices.lastdev) devices.lastdev->next = dev; else @@ -1139,8 +1233,10 @@ static struct device *new_device(const char *name, u16 type) return dev; } -/* Our first setup routine is the console. It's a fairly simple device, but - * UNIX tty handling makes it uglier than it could be. */ +/* + * Our first setup routine is the console. It's a fairly simple device, but + * UNIX tty handling makes it uglier than it could be. + */ static void setup_console(void) { struct device *dev; @@ -1148,8 +1244,10 @@ static void setup_console(void) /* If we can save the initial standard input settings... */ if (tcgetattr(STDIN_FILENO, &orig_term) == 0) { struct termios term = orig_term; - /* Then we turn off echo, line buffering and ^C etc. We want a - * raw input stream to the Guest. */ + /* + * Then we turn off echo, line buffering and ^C etc: We want a + * raw input stream to the Guest. + */ term.c_lflag &= ~(ISIG|ICANON|ECHO); tcsetattr(STDIN_FILENO, TCSANOW, &term); } @@ -1160,10 +1258,12 @@ static void setup_console(void) dev->priv = malloc(sizeof(struct console_abort)); ((struct console_abort *)dev->priv)->count = 0; - /* The console needs two virtqueues: the input then the output. When + /* + * The console needs two virtqueues: the input then the output. When * they put something the input queue, we make sure we're listening to * stdin. When they put something in the output queue, we write it to - * stdout. */ + * stdout. + */ add_virtqueue(dev, VIRTQUEUE_NUM, console_input); add_virtqueue(dev, VIRTQUEUE_NUM, console_output); @@ -1171,7 +1271,8 @@ static void setup_console(void) } /*:*/ -/*M:010 Inter-guest networking is an interesting area. Simplest is to have a +/*M:010 + * Inter-guest networking is an interesting area. Simplest is to have a * --sharenet= option which opens or creates a named pipe. This can be * used to send packets to another guest in a 1:1 manner. * @@ -1185,7 +1286,8 @@ static void setup_console(void) * multiple inter-guest channels behind one interface, although it would * require some manner of hotplugging new virtio channels. * - * Finally, we could implement a virtio network switch in the kernel. :*/ + * Finally, we could implement a virtio network switch in the kernel. +:*/ static u32 str2ip(const char *ipaddr) { @@ -1210,11 +1312,13 @@ static void str2mac(const char *macaddr, unsigned char mac[6]) mac[5] = m[5]; } -/* This code is "adapted" from libbridge: it attaches the Host end of the +/* + * This code is "adapted" from libbridge: it attaches the Host end of the * network device to the bridge device specified by the command line. * * This is yet another James Morris contribution (I'm an IP-level guy, so I - * dislike bridging), and I just try not to break it. */ + * dislike bridging), and I just try not to break it. + */ static void add_to_bridge(int fd, const char *if_name, const char *br_name) { int ifidx; @@ -1234,9 +1338,11 @@ static void add_to_bridge(int fd, const char *if_name, const char *br_name) err(1, "can't add %s to bridge %s", if_name, br_name); } -/* This sets up the Host end of the network device with an IP address, brings +/* + * This sets up the Host end of the network device with an IP address, brings * it up so packets will flow, the copies the MAC address into the hwaddr - * pointer. */ + * pointer. + */ static void configure_device(int fd, const char *tapif, u32 ipaddr) { struct ifreq ifr; @@ -1263,10 +1369,12 @@ static int get_tun_device(char tapif[IFNAMSIZ]) /* Start with this zeroed. Messy but sure. */ memset(&ifr, 0, sizeof(ifr)); - /* We open the /dev/net/tun device and tell it we want a tap device. A + /* + * We open the /dev/net/tun device and tell it we want a tap device. A * tap device is like a tun device, only somehow different. To tell * the truth, I completely blundered my way through this code, but it - * works now! */ + * works now! + */ netfd = open_or_die("/dev/net/tun", O_RDWR); ifr.ifr_flags = IFF_TAP | IFF_NO_PI | IFF_VNET_HDR; strcpy(ifr.ifr_name, "tap%d"); @@ -1277,18 +1385,22 @@ static int get_tun_device(char tapif[IFNAMSIZ]) TUN_F_CSUM|TUN_F_TSO4|TUN_F_TSO6|TUN_F_TSO_ECN) != 0) err(1, "Could not set features for tun device"); - /* We don't need checksums calculated for packets coming in this - * device: trust us! */ + /* + * We don't need checksums calculated for packets coming in this + * device: trust us! + */ ioctl(netfd, TUNSETNOCSUM, 1); memcpy(tapif, ifr.ifr_name, IFNAMSIZ); return netfd; } -/*L:195 Our network is a Host<->Guest network. This can either use bridging or +/*L:195 + * Our network is a Host<->Guest network. This can either use bridging or * routing, but the principle is the same: it uses the "tun" device to inject * packets into the Host as if they came in from a normal network card. We - * just shunt packets between the Guest and the tun device. */ + * just shunt packets between the Guest and the tun device. + */ static void setup_tun_net(char *arg) { struct device *dev; @@ -1305,13 +1417,14 @@ static void setup_tun_net(char *arg) dev = new_device("net", VIRTIO_ID_NET); dev->priv = net_info; - /* Network devices need a receive and a send queue, just like - * console. */ + /* Network devices need a recv and a send queue, just like console. */ add_virtqueue(dev, VIRTQUEUE_NUM, net_input); add_virtqueue(dev, VIRTQUEUE_NUM, net_output); - /* We need a socket to perform the magic network ioctls to bring up the - * tap interface, connect to the bridge etc. Any socket will do! */ + /* + * We need a socket to perform the magic network ioctls to bring up the + * tap interface, connect to the bridge etc. Any socket will do! + */ ipfd = socket(PF_INET, SOCK_DGRAM, IPPROTO_IP); if (ipfd < 0) err(1, "opening IP socket"); @@ -1366,7 +1479,8 @@ static void setup_tun_net(char *arg) devices.device_num, tapif, arg); } -/* Our block (disk) device should be really simple: the Guest asks for a block +/* + * Our block (disk) device should be really simple: the Guest asks for a block * number and we read or write that position in the file. Unfortunately, that * was amazingly slow: the Guest waits until the read is finished before * running anything else, even if it could have been doing useful work. @@ -1374,7 +1488,9 @@ static void setup_tun_net(char *arg) * We could use async I/O, except it's reputed to suck so hard that characters * actually go missing from your code when you try to use it. * - * So we farm the I/O out to thread, and communicate with it via a pipe. */ + * So this was one reason why lguest now does all virtqueue servicing in + * separate threads: it's more efficient and more like a real device. + */ /* This hangs off device->priv. */ struct vblk_info @@ -1412,9 +1528,11 @@ static void blk_request(struct virtqueue *vq) /* Get the next request. */ head = wait_for_vq_desc(vq, iov, &out_num, &in_num); - /* Every block request should contain at least one output buffer + /* + * Every block request should contain at least one output buffer * (detailing the location on disk and the type of request) and one - * input buffer (to hold the result). */ + * input buffer (to hold the result). + */ if (out_num == 0 || in_num == 0) errx(1, "Bad virtblk cmd %u out=%u in=%u", head, out_num, in_num); @@ -1423,33 +1541,41 @@ static void blk_request(struct virtqueue *vq) in = convert(&iov[out_num+in_num-1], u8); off = out->sector * 512; - /* The block device implements "barriers", where the Guest indicates + /* + * The block device implements "barriers", where the Guest indicates * that it wants all previous writes to occur before this write. We * don't have a way of asking our kernel to do a barrier, so we just - * synchronize all the data in the file. Pretty poor, no? */ + * synchronize all the data in the file. Pretty poor, no? + */ if (out->type & VIRTIO_BLK_T_BARRIER) fdatasync(vblk->fd); - /* In general the virtio block driver is allowed to try SCSI commands. - * It'd be nice if we supported eject, for example, but we don't. */ + /* + * In general the virtio block driver is allowed to try SCSI commands. + * It'd be nice if we supported eject, for example, but we don't. + */ if (out->type & VIRTIO_BLK_T_SCSI_CMD) { fprintf(stderr, "Scsi commands unsupported\n"); *in = VIRTIO_BLK_S_UNSUPP; wlen = sizeof(*in); } else if (out->type & VIRTIO_BLK_T_OUT) { - /* Write */ - - /* Move to the right location in the block file. This can fail - * if they try to write past end. */ + /* + * Write + * + * Move to the right location in the block file. This can fail + * if they try to write past end. + */ if (lseek64(vblk->fd, off, SEEK_SET) != off) err(1, "Bad seek to sector %llu", out->sector); ret = writev(vblk->fd, iov+1, out_num-1); verbose("WRITE to sector %llu: %i\n", out->sector, ret); - /* Grr... Now we know how long the descriptor they sent was, we + /* + * Grr... Now we know how long the descriptor they sent was, we * make sure they didn't try to write over the end of the block - * file (possibly extending it). */ + * file (possibly extending it). + */ if (ret > 0 && off + ret > vblk->len) { /* Trim it back to the correct length */ ftruncate64(vblk->fd, vblk->len); @@ -1459,10 +1585,12 @@ static void blk_request(struct virtqueue *vq) wlen = sizeof(*in); *in = (ret >= 0 ? VIRTIO_BLK_S_OK : VIRTIO_BLK_S_IOERR); } else { - /* Read */ - - /* Move to the right location in the block file. This can fail - * if they try to read past end. */ + /* + * Read + * + * Move to the right location in the block file. This can fail + * if they try to read past end. + */ if (lseek64(vblk->fd, off, SEEK_SET) != off) err(1, "Bad seek to sector %llu", out->sector); @@ -1477,10 +1605,12 @@ static void blk_request(struct virtqueue *vq) } } - /* OK, so we noted that it was pretty poor to use an fdatasync as a + /* + * OK, so we noted that it was pretty poor to use an fdatasync as a * barrier. But Christoph Hellwig points out that we need a sync * *afterwards* as well: "Barriers specify no reordering to the front - * or the back." And Jens Axboe confirmed it, so here we are: */ + * or the back." And Jens Axboe confirmed it, so here we are: + */ if (out->type & VIRTIO_BLK_T_BARRIER) fdatasync(vblk->fd); @@ -1494,7 +1624,7 @@ static void setup_block_file(const char *filename) struct vblk_info *vblk; struct virtio_blk_config conf; - /* The device responds to return from I/O thread. */ + /* Creat the device. */ dev = new_device("block", VIRTIO_ID_BLOCK); /* The device has one virtqueue, where the Guest places requests. */ @@ -1513,8 +1643,10 @@ static void setup_block_file(const char *filename) /* Tell Guest how many sectors this device has. */ conf.capacity = cpu_to_le64(vblk->len / 512); - /* Tell Guest not to put in too many descriptors at once: two are used - * for the in and out elements. */ + /* + * Tell Guest not to put in too many descriptors at once: two are used + * for the in and out elements. + */ add_feature(dev, VIRTIO_BLK_F_SEG_MAX); conf.seg_max = cpu_to_le32(VIRTQUEUE_NUM - 2); @@ -1525,16 +1657,18 @@ static void setup_block_file(const char *filename) ++devices.device_num, le64_to_cpu(conf.capacity)); } -struct rng_info { - int rfd; -}; - -/* Our random number generator device reads from /dev/random into the Guest's +/*L:211 + * Our random number generator device reads from /dev/random into the Guest's * input buffers. The usual case is that the Guest doesn't want random numbers * and so has no buffers although /dev/random is still readable, whereas * console is the reverse. * - * The same logic applies, however. */ + * The same logic applies, however. + */ +struct rng_info { + int rfd; +}; + static void rng_input(struct virtqueue *vq) { int len; @@ -1547,9 +1681,11 @@ static void rng_input(struct virtqueue *vq) if (out_num) errx(1, "Output buffers in rng?"); - /* This is why we convert to iovecs: the readv() call uses them, and so + /* + * This is why we convert to iovecs: the readv() call uses them, and so * it reads straight into the Guest's buffer. We loop to make sure we - * fill it. */ + * fill it. + */ while (!iov_empty(iov, in_num)) { len = readv(rng_info->rfd, iov, in_num); if (len <= 0) @@ -1562,15 +1698,18 @@ static void rng_input(struct virtqueue *vq) add_used(vq, head, totlen); } -/* And this creates a "hardware" random number device for the Guest. */ +/*L:199 + * This creates a "hardware" random number device for the Guest. + */ static void setup_rng(void) { struct device *dev; struct rng_info *rng_info = malloc(sizeof(*rng_info)); + /* Our device's privat info simply contains the /dev/random fd. */ rng_info->rfd = open_or_die("/dev/random", O_RDONLY); - /* The device responds to return from I/O thread. */ + /* Create the new device. */ dev = new_device("rng", VIRTIO_ID_RNG); dev->priv = rng_info; @@ -1586,8 +1725,10 @@ static void __attribute__((noreturn)) restart_guest(void) { unsigned int i; - /* Since we don't track all open fds, we simply close everything beyond - * stderr. */ + /* + * Since we don't track all open fds, we simply close everything beyond + * stderr. + */ for (i = 3; i < FD_SETSIZE; i++) close(i); @@ -1598,8 +1739,10 @@ static void __attribute__((noreturn)) restart_guest(void) err(1, "Could not exec %s", main_args[0]); } -/*L:220 Finally we reach the core of the Launcher which runs the Guest, serves - * its input and output, and finally, lays it to rest. */ +/*L:220 + * Finally we reach the core of the Launcher which runs the Guest, serves + * its input and output, and finally, lays it to rest. + */ static void __attribute__((noreturn)) run_guest(void) { for (;;) { @@ -1634,7 +1777,7 @@ static void __attribute__((noreturn)) run_guest(void) * * Are you ready? Take a deep breath and join me in the core of the Host, in * "make Host". - :*/ +:*/ static struct option opts[] = { { "verbose", 0, NULL, 'v' }, @@ -1655,8 +1798,7 @@ static void usage(void) /*L:105 The main routine is where the real work begins: */ int main(int argc, char *argv[]) { - /* Memory, top-level pagetable, code startpoint and size of the - * (optional) initrd. */ + /* Memory, code startpoint and size of the (optional) initrd. */ unsigned long mem = 0, start, initrd_size = 0; /* Two temporaries. */ int i, c; @@ -1668,24 +1810,30 @@ int main(int argc, char *argv[]) /* Save the args: we "reboot" by execing ourselves again. */ main_args = argv; - /* First we initialize the device list. We keep a pointer to the last + /* + * First we initialize the device list. We keep a pointer to the last * device, and the next interrupt number to use for devices (1: - * remember that 0 is used by the timer). */ + * remember that 0 is used by the timer). + */ devices.lastdev = NULL; devices.next_irq = 1; cpu_id = 0; - /* We need to know how much memory so we can set up the device + /* + * We need to know how much memory so we can set up the device * descriptor and memory pages for the devices as we parse the command * line. So we quickly look through the arguments to find the amount - * of memory now. */ + * of memory now. + */ for (i = 1; i < argc; i++) { if (argv[i][0] != '-') { mem = atoi(argv[i]) * 1024 * 1024; - /* We start by mapping anonymous pages over all of + /* + * We start by mapping anonymous pages over all of * guest-physical memory range. This fills it with 0, * and ensures that the Guest won't be killed when it - * tries to access it. */ + * tries to access it. + */ guest_base = map_zeroed_pages(mem / getpagesize() + DEVICE_PAGES); guest_limit = mem; @@ -1718,8 +1866,10 @@ int main(int argc, char *argv[]) usage(); } } - /* After the other arguments we expect memory and kernel image name, - * followed by command line arguments for the kernel. */ + /* + * After the other arguments we expect memory and kernel image name, + * followed by command line arguments for the kernel. + */ if (optind + 2 > argc) usage(); @@ -1737,20 +1887,26 @@ int main(int argc, char *argv[]) /* Map the initrd image if requested (at top of physical memory) */ if (initrd_name) { initrd_size = load_initrd(initrd_name, mem); - /* These are the location in the Linux boot header where the - * start and size of the initrd are expected to be found. */ + /* + * These are the location in the Linux boot header where the + * start and size of the initrd are expected to be found. + */ boot->hdr.ramdisk_image = mem - initrd_size; boot->hdr.ramdisk_size = initrd_size; /* The bootloader type 0xFF means "unknown"; that's OK. */ boot->hdr.type_of_loader = 0xFF; } - /* The Linux boot header contains an "E820" memory map: ours is a - * simple, single region. */ + /* + * The Linux boot header contains an "E820" memory map: ours is a + * simple, single region. + */ boot->e820_entries = 1; boot->e820_map[0] = ((struct e820entry) { 0, mem, E820_RAM }); - /* The boot header contains a command line pointer: we put the command - * line after the boot header. */ + /* + * The boot header contains a command line pointer: we put the command + * line after the boot header. + */ boot->hdr.cmd_line_ptr = to_guest_phys(boot + 1); /* We use a simple helper to copy the arguments separated by spaces. */ concat((char *)(boot + 1), argv+optind+2); @@ -1764,8 +1920,10 @@ int main(int argc, char *argv[]) /* Tell the entry path not to try to reload segment registers. */ boot->hdr.loadflags |= KEEP_SEGMENTS; - /* We tell the kernel to initialize the Guest: this returns the open - * /dev/lguest file descriptor. */ + /* + * We tell the kernel to initialize the Guest: this returns the open + * /dev/lguest file descriptor. + */ tell_kernel(start); /* Ensure that we terminate if a child dies. */ diff --git a/arch/x86/include/asm/lguest.h b/arch/x86/include/asm/lguest.h index 313389cd50d..5136dad57cb 100644 --- a/arch/x86/include/asm/lguest.h +++ b/arch/x86/include/asm/lguest.h @@ -17,8 +17,7 @@ /* Pages for switcher itself, then two pages per cpu */ #define TOTAL_SWITCHER_PAGES (SHARED_SWITCHER_PAGES + 2 * nr_cpu_ids) -/* We map at -4M (-2M when PAE is activated) for ease of mapping - * into the guest (one PTE page). */ +/* We map at -4M (-2M for PAE) for ease of mapping (one PTE page). */ #ifdef CONFIG_X86_PAE #define SWITCHER_ADDR 0xFFE00000 #else diff --git a/arch/x86/include/asm/lguest_hcall.h b/arch/x86/include/asm/lguest_hcall.h index 33600a66755..cceb73e12e5 100644 --- a/arch/x86/include/asm/lguest_hcall.h +++ b/arch/x86/include/asm/lguest_hcall.h @@ -30,7 +30,8 @@ #include #include -/*G:030 But first, how does our Guest contact the Host to ask for privileged +/*G:030 + * But first, how does our Guest contact the Host to ask for privileged * operations? There are two ways: the direct way is to make a "hypercall", * to make requests of the Host Itself. * @@ -41,16 +42,15 @@ * * Grossly invalid calls result in Sudden Death at the hands of the vengeful * Host, rather than returning failure. This reflects Winston Churchill's - * definition of a gentleman: "someone who is only rude intentionally". */ -/*:*/ + * definition of a gentleman: "someone who is only rude intentionally". +:*/ /* Can't use our min() macro here: needs to be a constant */ #define LGUEST_IRQS (NR_IRQS < 32 ? NR_IRQS: 32) #define LHCALL_RING_SIZE 64 struct hcall_args { - /* These map directly onto eax, ebx, ecx, edx and esi - * in struct lguest_regs */ + /* These map directly onto eax/ebx/ecx/edx/esi in struct lguest_regs */ unsigned long arg0, arg1, arg2, arg3, arg4; }; diff --git a/arch/x86/lguest/boot.c b/arch/x86/lguest/boot.c index f2bf1f73d46..025c04d18f2 100644 --- a/arch/x86/lguest/boot.c +++ b/arch/x86/lguest/boot.c @@ -22,7 +22,8 @@ * * So how does the kernel know it's a Guest? We'll see that later, but let's * just say that we end up here where we replace the native functions various - * "paravirt" structures with our Guest versions, then boot like normal. :*/ + * "paravirt" structures with our Guest versions, then boot like normal. +:*/ /* * Copyright (C) 2006, Rusty Russell IBM Corporation. @@ -74,7 +75,8 @@ * * The Guest in our tale is a simple creature: identical to the Host but * behaving in simplified but equivalent ways. In particular, the Guest is the - * same kernel as the Host (or at least, built from the same source code). :*/ + * same kernel as the Host (or at least, built from the same source code). +:*/ struct lguest_data lguest_data = { .hcall_status = { [0 ... LHCALL_RING_SIZE-1] = 0xFF }, @@ -85,7 +87,8 @@ struct lguest_data lguest_data = { .syscall_vec = SYSCALL_VECTOR, }; -/*G:037 async_hcall() is pretty simple: I'm quite proud of it really. We have a +/*G:037 + * async_hcall() is pretty simple: I'm quite proud of it really. We have a * ring buffer of stored hypercalls which the Host will run though next time we * do a normal hypercall. Each entry in the ring has 5 slots for the hypercall * arguments, and a "hcall_status" word which is 0 if the call is ready to go, @@ -94,7 +97,8 @@ struct lguest_data lguest_data = { * If we come around to a slot which hasn't been finished, then the table is * full and we just make the hypercall directly. This has the nice side * effect of causing the Host to run all the stored calls in the ring buffer - * which empties it for next time! */ + * which empties it for next time! + */ static void async_hcall(unsigned long call, unsigned long arg1, unsigned long arg2, unsigned long arg3, unsigned long arg4) @@ -103,9 +107,11 @@ static void async_hcall(unsigned long call, unsigned long arg1, static unsigned int next_call; unsigned long flags; - /* Disable interrupts if not already disabled: we don't want an + /* + * Disable interrupts if not already disabled: we don't want an * interrupt handler making a hypercall while we're already doing - * one! */ + * one! + */ local_irq_save(flags); if (lguest_data.hcall_status[next_call] != 0xFF) { /* Table full, so do normal hcall which will flush table. */ @@ -125,8 +131,9 @@ static void async_hcall(unsigned long call, unsigned long arg1, local_irq_restore(flags); } -/*G:035 Notice the lazy_hcall() above, rather than hcall(). This is our first - * real optimization trick! +/*G:035 + * Notice the lazy_hcall() above, rather than hcall(). This is our first real + * optimization trick! * * When lazy_mode is set, it means we're allowed to defer all hypercalls and do * them as a batch when lazy_mode is eventually turned off. Because hypercalls @@ -136,7 +143,8 @@ static void async_hcall(unsigned long call, unsigned long arg1, * lguest_leave_lazy_mode(). * * So, when we're in lazy mode, we call async_hcall() to store the call for - * future processing: */ + * future processing: + */ static void lazy_hcall1(unsigned long call, unsigned long arg1) { @@ -208,9 +216,11 @@ static void lguest_end_context_switch(struct task_struct *next) * check there before it tries to deliver an interrupt. */ -/* save_flags() is expected to return the processor state (ie. "flags"). The +/* + * save_flags() is expected to return the processor state (ie. "flags"). The * flags word contains all kind of stuff, but in practice Linux only cares - * about the interrupt flag. Our "save_flags()" just returns that. */ + * about the interrupt flag. Our "save_flags()" just returns that. + */ static unsigned long save_fl(void) { return lguest_data.irq_enabled; @@ -222,13 +232,15 @@ static void irq_disable(void) lguest_data.irq_enabled = 0; } -/* Let's pause a moment. Remember how I said these are called so often? +/* + * Let's pause a moment. Remember how I said these are called so often? * Jeremy Fitzhardinge optimized them so hard early in 2009 that he had to * break some rules. In particular, these functions are assumed to save their * own registers if they need to: normal C functions assume they can trash the * eax register. To use normal C functions, we use * PV_CALLEE_SAVE_REGS_THUNK(), which pushes %eax onto the stack, calls the - * C function, then restores it. */ + * C function, then restores it. + */ PV_CALLEE_SAVE_REGS_THUNK(save_fl); PV_CALLEE_SAVE_REGS_THUNK(irq_disable); /*:*/ @@ -237,18 +249,20 @@ PV_CALLEE_SAVE_REGS_THUNK(irq_disable); extern void lg_irq_enable(void); extern void lg_restore_fl(unsigned long flags); -/*M:003 Note that we don't check for outstanding interrupts when we re-enable - * them (or when we unmask an interrupt). This seems to work for the moment, - * since interrupts are rare and we'll just get the interrupt on the next timer - * tick, but now we can run with CONFIG_NO_HZ, we should revisit this. One way - * would be to put the "irq_enabled" field in a page by itself, and have the - * Host write-protect it when an interrupt comes in when irqs are disabled. - * There will then be a page fault as soon as interrupts are re-enabled. +/*M:003 + * Note that we don't check for outstanding interrupts when we re-enable them + * (or when we unmask an interrupt). This seems to work for the moment, since + * interrupts are rare and we'll just get the interrupt on the next timer tick, + * but now we can run with CONFIG_NO_HZ, we should revisit this. One way would + * be to put the "irq_enabled" field in a page by itself, and have the Host + * write-protect it when an interrupt comes in when irqs are disabled. There + * will then be a page fault as soon as interrupts are re-enabled. * * A better method is to implement soft interrupt disable generally for x86: * instead of disabling interrupts, we set a flag. If an interrupt does come * in, we then disable them for real. This is uncommon, so we could simply use - * a hypercall for interrupt control and not worry about efficiency. :*/ + * a hypercall for interrupt control and not worry about efficiency. +:*/ /*G:034 * The Interrupt Descriptor Table (IDT). @@ -261,10 +275,12 @@ extern void lg_restore_fl(unsigned long flags); static void lguest_write_idt_entry(gate_desc *dt, int entrynum, const gate_desc *g) { - /* The gate_desc structure is 8 bytes long: we hand it to the Host in + /* + * The gate_desc structure is 8 bytes long: we hand it to the Host in * two 32-bit chunks. The whole 32-bit kernel used to hand descriptors * around like this; typesafety wasn't a big concern in Linux's early - * years. */ + * years. + */ u32 *desc = (u32 *)g; /* Keep the local copy up to date. */ native_write_idt_entry(dt, entrynum, g); @@ -272,9 +288,11 @@ static void lguest_write_idt_entry(gate_desc *dt, kvm_hypercall3(LHCALL_LOAD_IDT_ENTRY, entrynum, desc[0], desc[1]); } -/* Changing to a different IDT is very rare: we keep the IDT up-to-date every +/* + * Changing to a different IDT is very rare: we keep the IDT up-to-date every * time it is written, so we can simply loop through all entries and tell the - * Host about them. */ + * Host about them. + */ static void lguest_load_idt(const struct desc_ptr *desc) { unsigned int i; @@ -305,9 +323,11 @@ static void lguest_load_gdt(const struct desc_ptr *desc) kvm_hypercall3(LHCALL_LOAD_GDT_ENTRY, i, gdt[i].a, gdt[i].b); } -/* For a single GDT entry which changes, we do the lazy thing: alter our GDT, +/* + * For a single GDT entry which changes, we do the lazy thing: alter our GDT, * then tell the Host to reload the entire thing. This operation is so rare - * that this naive implementation is reasonable. */ + * that this naive implementation is reasonable. + */ static void lguest_write_gdt_entry(struct desc_struct *dt, int entrynum, const void *desc, int type) { @@ -317,29 +337,36 @@ static void lguest_write_gdt_entry(struct desc_struct *dt, int entrynum, dt[entrynum].a, dt[entrynum].b); } -/* OK, I lied. There are three "thread local storage" GDT entries which change +/* + * OK, I lied. There are three "thread local storage" GDT entries which change * on every context switch (these three entries are how glibc implements - * __thread variables). So we have a hypercall specifically for this case. */ + * __thread variables). So we have a hypercall specifically for this case. + */ static void lguest_load_tls(struct thread_struct *t, unsigned int cpu) { - /* There's one problem which normal hardware doesn't have: the Host + /* + * There's one problem which normal hardware doesn't have: the Host * can't handle us removing entries we're currently using. So we clear - * the GS register here: if it's needed it'll be reloaded anyway. */ + * the GS register here: if it's needed it'll be reloaded anyway. + */ lazy_load_gs(0); lazy_hcall2(LHCALL_LOAD_TLS, __pa(&t->tls_array), cpu); } -/*G:038 That's enough excitement for now, back to ploughing through each of - * the different pv_ops structures (we're about 1/3 of the way through). +/*G:038 + * That's enough excitement for now, back to ploughing through each of the + * different pv_ops structures (we're about 1/3 of the way through). * * This is the Local Descriptor Table, another weird Intel thingy. Linux only * uses this for some strange applications like Wine. We don't do anything - * here, so they'll get an informative and friendly Segmentation Fault. */ + * here, so they'll get an informative and friendly Segmentation Fault. + */ static void lguest_set_ldt(const void *addr, unsigned entries) { } -/* This loads a GDT entry into the "Task Register": that entry points to a +/* + * This loads a GDT entry into the "Task Register": that entry points to a * structure called the Task State Segment. Some comments scattered though the * kernel code indicate that this used for task switching in ages past, along * with blood sacrifice and astrology. @@ -347,19 +374,21 @@ static void lguest_set_ldt(const void *addr, unsigned entries) * Now there's nothing interesting in here that we don't get told elsewhere. * But the native version uses the "ltr" instruction, which makes the Host * complain to the Guest about a Segmentation Fault and it'll oops. So we - * override the native version with a do-nothing version. */ + * override the native version with a do-nothing version. + */ static void lguest_load_tr_desc(void) { } -/* The "cpuid" instruction is a way of querying both the CPU identity +/* + * The "cpuid" instruction is a way of querying both the CPU identity * (manufacturer, model, etc) and its features. It was introduced before the * Pentium in 1993 and keeps getting extended by both Intel, AMD and others. * As you might imagine, after a decade and a half this treatment, it is now a * giant ball of hair. Its entry in the current Intel manual runs to 28 pages. * * This instruction even it has its own Wikipedia entry. The Wikipedia entry - * has been translated into 4 languages. I am not making this up! + * has been translated into 5 languages. I am not making this up! * * We could get funky here and identify ourselves as "GenuineLguest", but * instead we just use the real "cpuid" instruction. Then I pretty much turned @@ -371,7 +400,8 @@ static void lguest_load_tr_desc(void) * Replacing the cpuid so we can turn features off is great for the kernel, but * anyone (including userspace) can just use the raw "cpuid" instruction and * the Host won't even notice since it isn't privileged. So we try not to get - * too worked up about it. */ + * too worked up about it. + */ static void lguest_cpuid(unsigned int *ax, unsigned int *bx, unsigned int *cx, unsigned int *dx) { @@ -379,43 +409,63 @@ static void lguest_cpuid(unsigned int *ax, unsigned int *bx, native_cpuid(ax, bx, cx, dx); switch (function) { - case 0: /* ID and highest CPUID. Futureproof a little by sticking to - * older ones. */ + /* + * CPUID 0 gives the highest legal CPUID number (and the ID string). + * We futureproof our code a little by sticking to known CPUID values. + */ + case 0: if (*ax > 5) *ax = 5; break; - case 1: /* Basic feature request. */ - /* We only allow kernel to see SSE3, CMPXCHG16B and SSSE3 */ + + /* + * CPUID 1 is a basic feature request. + * + * CX: we only allow kernel to see SSE3, CMPXCHG16B and SSSE3 + * DX: SSE, SSE2, FXSR, MMX, CMOV, CMPXCHG8B, TSC, FPU and PAE. + */ + case 1: *cx &= 0x00002201; - /* SSE, SSE2, FXSR, MMX, CMOV, CMPXCHG8B, TSC, FPU, PAE. */ *dx &= 0x07808151; - /* The Host can do a nice optimization if it knows that the + /* + * The Host can do a nice optimization if it knows that the * kernel mappings (addresses above 0xC0000000 or whatever * PAGE_OFFSET is set to) haven't changed. But Linux calls * flush_tlb_user() for both user and kernel mappings unless - * the Page Global Enable (PGE) feature bit is set. */ + * the Page Global Enable (PGE) feature bit is set. + */ *dx |= 0x00002000; - /* We also lie, and say we're family id 5. 6 or greater + /* + * We also lie, and say we're family id 5. 6 or greater * leads to a rdmsr in early_init_intel which we can't handle. - * Family ID is returned as bits 8-12 in ax. */ + * Family ID is returned as bits 8-12 in ax. + */ *ax &= 0xFFFFF0FF; *ax |= 0x00000500; break; + /* + * 0x80000000 returns the highest Extended Function, so we futureproof + * like we do above by limiting it to known fields. + */ case 0x80000000: - /* Futureproof this a little: if they ask how much extended - * processor information there is, limit it to known fields. */ if (*ax > 0x80000008) *ax = 0x80000008; break; + + /* + * PAE systems can mark pages as non-executable. Linux calls this the + * NX bit. Intel calls it XD (eXecute Disable), AMD EVP (Enhanced + * Virus Protection). We just switch turn if off here, since we don't + * support it. + */ case 0x80000001: - /* Here we should fix nx cap depending on host. */ - /* For this version of PAE, we just clear NX bit. */ *dx &= ~(1 << 20); break; } } -/* Intel has four control registers, imaginatively named cr0, cr2, cr3 and cr4. +/* + * Intel has four control registers, imaginatively named cr0, cr2, cr3 and cr4. * I assume there's a cr1, but it hasn't bothered us yet, so we'll not bother * it. The Host needs to know when the Guest wants to change them, so we have * a whole series of functions like read_cr0() and write_cr0(). @@ -430,7 +480,8 @@ static void lguest_cpuid(unsigned int *ax, unsigned int *bx, * name like "FPUTRAP bit" be a little less cryptic? * * We store cr0 locally because the Host never changes it. The Guest sometimes - * wants to read it and we'd prefer not to bother the Host unnecessarily. */ + * wants to read it and we'd prefer not to bother the Host unnecessarily. + */ static unsigned long current_cr0; static void lguest_write_cr0(unsigned long val) { @@ -443,18 +494,22 @@ static unsigned long lguest_read_cr0(void) return current_cr0; } -/* Intel provided a special instruction to clear the TS bit for people too cool +/* + * Intel provided a special instruction to clear the TS bit for people too cool * to use write_cr0() to do it. This "clts" instruction is faster, because all - * the vowels have been optimized out. */ + * the vowels have been optimized out. + */ static void lguest_clts(void) { lazy_hcall1(LHCALL_TS, 0); current_cr0 &= ~X86_CR0_TS; } -/* cr2 is the virtual address of the last page fault, which the Guest only ever +/* + * cr2 is the virtual address of the last page fault, which the Guest only ever * reads. The Host kindly writes this into our "struct lguest_data", so we - * just read it out of there. */ + * just read it out of there. + */ static unsigned long lguest_read_cr2(void) { return lguest_data.cr2; @@ -463,10 +518,12 @@ static unsigned long lguest_read_cr2(void) /* See lguest_set_pte() below. */ static bool cr3_changed = false; -/* cr3 is the current toplevel pagetable page: the principle is the same as +/* + * cr3 is the current toplevel pagetable page: the principle is the same as * cr0. Keep a local copy, and tell the Host when it changes. The only * difference is that our local copy is in lguest_data because the Host needs - * to set it upon our initial hypercall. */ + * to set it upon our initial hypercall. + */ static void lguest_write_cr3(unsigned long cr3) { lguest_data.pgdir = cr3; @@ -538,10 +595,12 @@ static void lguest_write_cr4(unsigned long val) * the real page tables based on the Guests'. */ -/* The Guest calls this to set a second-level entry (pte), ie. to map a page +/* + * The Guest calls this to set a second-level entry (pte), ie. to map a page * into a process' address space. We set the entry then tell the Host the * toplevel and address this corresponds to. The Guest uses one pagetable per - * process, so we need to tell the Host which one we're changing (mm->pgd). */ + * process, so we need to tell the Host which one we're changing (mm->pgd). + */ static void lguest_pte_update(struct mm_struct *mm, unsigned long addr, pte_t *ptep) { @@ -560,10 +619,13 @@ static void lguest_set_pte_at(struct mm_struct *mm, unsigned long addr, lguest_pte_update(mm, addr, ptep); } -/* The Guest calls lguest_set_pud to set a top-level entry and lguest_set_pmd +/* + * The Guest calls lguest_set_pud to set a top-level entry and lguest_set_pmd * to set a middle-level entry when PAE is activated. + * * Again, we set the entry then tell the Host which page we changed, - * and the index of the entry we changed. */ + * and the index of the entry we changed. + */ #ifdef CONFIG_X86_PAE static void lguest_set_pud(pud_t *pudp, pud_t pudval) { @@ -582,8 +644,7 @@ static void lguest_set_pmd(pmd_t *pmdp, pmd_t pmdval) } #else -/* The Guest calls lguest_set_pmd to set a top-level entry when PAE is not - * activated. */ +/* The Guest calls lguest_set_pmd to set a top-level entry when !PAE. */ static void lguest_set_pmd(pmd_t *pmdp, pmd_t pmdval) { native_set_pmd(pmdp, pmdval); @@ -592,7 +653,8 @@ static void lguest_set_pmd(pmd_t *pmdp, pmd_t pmdval) } #endif -/* There are a couple of legacy places where the kernel sets a PTE, but we +/* + * There are a couple of legacy places where the kernel sets a PTE, but we * don't know the top level any more. This is useless for us, since we don't * know which pagetable is changing or what address, so we just tell the Host * to forget all of them. Fortunately, this is very rare. @@ -600,7 +662,8 @@ static void lguest_set_pmd(pmd_t *pmdp, pmd_t pmdval) * ... except in early boot when the kernel sets up the initial pagetables, * which makes booting astonishingly slow: 1.83 seconds! So we don't even tell * the Host anything changed until we've done the first page table switch, - * which brings boot back to 0.25 seconds. */ + * which brings boot back to 0.25 seconds. + */ static void lguest_set_pte(pte_t *ptep, pte_t pteval) { native_set_pte(ptep, pteval); @@ -628,7 +691,8 @@ void lguest_pmd_clear(pmd_t *pmdp) } #endif -/* Unfortunately for Lguest, the pv_mmu_ops for page tables were based on +/* + * Unfortunately for Lguest, the pv_mmu_ops for page tables were based on * native page table operations. On native hardware you can set a new page * table entry whenever you want, but if you want to remove one you have to do * a TLB flush (a TLB is a little cache of page table entries kept by the CPU). @@ -637,24 +701,29 @@ void lguest_pmd_clear(pmd_t *pmdp) * called when a valid entry is written, not when it's removed (ie. marked not * present). Instead, this is where we come when the Guest wants to remove a * page table entry: we tell the Host to set that entry to 0 (ie. the present - * bit is zero). */ + * bit is zero). + */ static void lguest_flush_tlb_single(unsigned long addr) { /* Simply set it to zero: if it was not, it will fault back in. */ lazy_hcall3(LHCALL_SET_PTE, lguest_data.pgdir, addr, 0); } -/* This is what happens after the Guest has removed a large number of entries. +/* + * This is what happens after the Guest has removed a large number of entries. * This tells the Host that any of the page table entries for userspace might - * have changed, ie. virtual addresses below PAGE_OFFSET. */ + * have changed, ie. virtual addresses below PAGE_OFFSET. + */ static void lguest_flush_tlb_user(void) { lazy_hcall1(LHCALL_FLUSH_TLB, 0); } -/* This is called when the kernel page tables have changed. That's not very +/* + * This is called when the kernel page tables have changed. That's not very * common (unless the Guest is using highmem, which makes the Guest extremely - * slow), so it's worth separating this from the user flushing above. */ + * slow), so it's worth separating this from the user flushing above. + */ static void lguest_flush_tlb_kernel(void) { lazy_hcall1(LHCALL_FLUSH_TLB, 1); @@ -691,23 +760,27 @@ static struct irq_chip lguest_irq_controller = { .unmask = enable_lguest_irq, }; -/* This sets up the Interrupt Descriptor Table (IDT) entry for each hardware +/* + * This sets up the Interrupt Descriptor Table (IDT) entry for each hardware * interrupt (except 128, which is used for system calls), and then tells the * Linux infrastructure that each interrupt is controlled by our level-based - * lguest interrupt controller. */ + * lguest interrupt controller. + */ static void __init lguest_init_IRQ(void) { unsigned int i; for (i = FIRST_EXTERNAL_VECTOR; i < NR_VECTORS; i++) { - /* Some systems map "vectors" to interrupts weirdly. Lguest has - * a straightforward 1 to 1 mapping, so force that here. */ + /* Some systems map "vectors" to interrupts weirdly. Not us! */ __get_cpu_var(vector_irq)[i] = i - FIRST_EXTERNAL_VECTOR; if (i != SYSCALL_VECTOR) set_intr_gate(i, interrupt[i - FIRST_EXTERNAL_VECTOR]); } - /* This call is required to set up for 4k stacks, where we have - * separate stacks for hard and soft interrupts. */ + + /* + * This call is required to set up for 4k stacks, where we have + * separate stacks for hard and soft interrupts. + */ irq_ctx_init(smp_processor_id()); } @@ -729,31 +802,39 @@ static unsigned long lguest_get_wallclock(void) return lguest_data.time.tv_sec; } -/* The TSC is an Intel thing called the Time Stamp Counter. The Host tells us +/* + * The TSC is an Intel thing called the Time Stamp Counter. The Host tells us * what speed it runs at, or 0 if it's unusable as a reliable clock source. * This matches what we want here: if we return 0 from this function, the x86 - * TSC clock will give up and not register itself. */ + * TSC clock will give up and not register itself. + */ static unsigned long lguest_tsc_khz(void) { return lguest_data.tsc_khz; } -/* If we can't use the TSC, the kernel falls back to our lower-priority - * "lguest_clock", where we read the time value given to us by the Host. */ +/* + * If we can't use the TSC, the kernel falls back to our lower-priority + * "lguest_clock", where we read the time value given to us by the Host. + */ static cycle_t lguest_clock_read(struct clocksource *cs) { unsigned long sec, nsec; - /* Since the time is in two parts (seconds and nanoseconds), we risk + /* + * Since the time is in two parts (seconds and nanoseconds), we risk * reading it just as it's changing from 99 & 0.999999999 to 100 and 0, * and getting 99 and 0. As Linux tends to come apart under the stress - * of time travel, we must be careful: */ + * of time travel, we must be careful: + */ do { /* First we read the seconds part. */ sec = lguest_data.time.tv_sec; - /* This read memory barrier tells the compiler and the CPU that + /* + * This read memory barrier tells the compiler and the CPU that * this can't be reordered: we have to complete the above - * before going on. */ + * before going on. + */ rmb(); /* Now we read the nanoseconds part. */ nsec = lguest_data.time.tv_nsec; @@ -777,9 +858,11 @@ static struct clocksource lguest_clock = { .flags = CLOCK_SOURCE_IS_CONTINUOUS, }; -/* We also need a "struct clock_event_device": Linux asks us to set it to go +/* + * We also need a "struct clock_event_device": Linux asks us to set it to go * off some time in the future. Actually, James Morris figured all this out, I - * just applied the patch. */ + * just applied the patch. + */ static int lguest_clockevent_set_next_event(unsigned long delta, struct clock_event_device *evt) { @@ -829,8 +912,10 @@ static struct clock_event_device lguest_clockevent = { .max_delta_ns = LG_CLOCK_MAX_DELTA, }; -/* This is the Guest timer interrupt handler (hardware interrupt 0). We just - * call the clockevent infrastructure and it does whatever needs doing. */ +/* + * This is the Guest timer interrupt handler (hardware interrupt 0). We just + * call the clockevent infrastructure and it does whatever needs doing. + */ static void lguest_time_irq(unsigned int irq, struct irq_desc *desc) { unsigned long flags; @@ -841,10 +926,12 @@ static void lguest_time_irq(unsigned int irq, struct irq_desc *desc) local_irq_restore(flags); } -/* At some point in the boot process, we get asked to set up our timing +/* + * At some point in the boot process, we get asked to set up our timing * infrastructure. The kernel doesn't expect timer interrupts before this, but * we cleverly initialized the "blocked_interrupts" field of "struct - * lguest_data" so that timer interrupts were blocked until now. */ + * lguest_data" so that timer interrupts were blocked until now. + */ static void lguest_time_init(void) { /* Set up the timer interrupt (0) to go to our simple timer routine */ @@ -868,14 +955,16 @@ static void lguest_time_init(void) * to work. They're pretty simple. */ -/* The Guest needs to tell the Host what stack it expects traps to use. For +/* + * The Guest needs to tell the Host what stack it expects traps to use. For * native hardware, this is part of the Task State Segment mentioned above in * lguest_load_tr_desc(), but to help hypervisors there's this special call. * * We tell the Host the segment we want to use (__KERNEL_DS is the kernel data * segment), the privilege level (we're privilege level 1, the Host is 0 and * will not tolerate us trying to use that), the stack pointer, and the number - * of pages in the stack. */ + * of pages in the stack. + */ static void lguest_load_sp0(struct tss_struct *tss, struct thread_struct *thread) { @@ -889,7 +978,8 @@ static void lguest_set_debugreg(int regno, unsigned long value) /* FIXME: Implement */ } -/* There are times when the kernel wants to make sure that no memory writes are +/* + * There are times when the kernel wants to make sure that no memory writes are * caught in the cache (that they've all reached real hardware devices). This * doesn't matter for the Guest which has virtual hardware. * @@ -903,11 +993,13 @@ static void lguest_wbinvd(void) { } -/* If the Guest expects to have an Advanced Programmable Interrupt Controller, +/* + * If the Guest expects to have an Advanced Programmable Interrupt Controller, * we play dumb by ignoring writes and returning 0 for reads. So it's no * longer Programmable nor Controlling anything, and I don't think 8 lines of * code qualifies for Advanced. It will also never interrupt anything. It - * does, however, allow us to get through the Linux boot code. */ + * does, however, allow us to get through the Linux boot code. + */ #ifdef CONFIG_X86_LOCAL_APIC static void lguest_apic_write(u32 reg, u32 v) { @@ -956,11 +1048,13 @@ static void lguest_safe_halt(void) kvm_hypercall0(LHCALL_HALT); } -/* The SHUTDOWN hypercall takes a string to describe what's happening, and +/* + * The SHUTDOWN hypercall takes a string to describe what's happening, and * an argument which says whether this to restart (reboot) the Guest or not. * * Note that the Host always prefers that the Guest speak in physical addresses - * rather than virtual addresses, so we use __pa() here. */ + * rather than virtual addresses, so we use __pa() here. + */ static void lguest_power_off(void) { kvm_hypercall2(LHCALL_SHUTDOWN, __pa("Power down"), @@ -991,8 +1085,10 @@ static __init char *lguest_memory_setup(void) * nice to move it back to lguest_init. Patch welcome... */ atomic_notifier_chain_register(&panic_notifier_list, &paniced); - /* The Linux bootloader header contains an "e820" memory map: the - * Launcher populated the first entry with our memory limit. */ + /* + *The Linux bootloader header contains an "e820" memory map: the + * Launcher populated the first entry with our memory limit. + */ e820_add_region(boot_params.e820_map[0].addr, boot_params.e820_map[0].size, boot_params.e820_map[0].type); @@ -1001,16 +1097,17 @@ static __init char *lguest_memory_setup(void) return "LGUEST"; } -/* We will eventually use the virtio console device to produce console output, +/* + * We will eventually use the virtio console device to produce console output, * but before that is set up we use LHCALL_NOTIFY on normal memory to produce - * console output. */ + * console output. + */ static __init int early_put_chars(u32 vtermno, const char *buf, int count) { char scratch[17]; unsigned int len = count; - /* We use a nul-terminated string, so we have to make a copy. Icky, - * huh? */ + /* We use a nul-terminated string, so we make a copy. Icky, huh? */ if (len > sizeof(scratch) - 1) len = sizeof(scratch) - 1; scratch[len] = '\0'; @@ -1021,8 +1118,10 @@ static __init int early_put_chars(u32 vtermno, const char *buf, int count) return len; } -/* Rebooting also tells the Host we're finished, but the RESTART flag tells the - * Launcher to reboot us. */ +/* + * Rebooting also tells the Host we're finished, but the RESTART flag tells the + * Launcher to reboot us. + */ static void lguest_restart(char *reason) { kvm_hypercall2(LHCALL_SHUTDOWN, __pa(reason), LGUEST_SHUTDOWN_RESTART); @@ -1049,7 +1148,8 @@ static void lguest_restart(char *reason) * fit comfortably. * * First we need assembly templates of each of the patchable Guest operations, - * and these are in i386_head.S. */ + * and these are in i386_head.S. + */ /*G:060 We construct a table from the assembler templates: */ static const struct lguest_insns @@ -1060,9 +1160,11 @@ static const struct lguest_insns [PARAVIRT_PATCH(pv_irq_ops.save_fl)] = { lgstart_pushf, lgend_pushf }, }; -/* Now our patch routine is fairly simple (based on the native one in +/* + * Now our patch routine is fairly simple (based on the native one in * paravirt.c). If we have a replacement, we copy it in and return how much of - * the available space we used. */ + * the available space we used. + */ static unsigned lguest_patch(u8 type, u16 clobber, void *ibuf, unsigned long addr, unsigned len) { @@ -1074,8 +1176,7 @@ static unsigned lguest_patch(u8 type, u16 clobber, void *ibuf, insn_len = lguest_insns[type].end - lguest_insns[type].start; - /* Similarly if we can't fit replacement (shouldn't happen, but let's - * be thorough). */ + /* Similarly if it can't fit (doesn't happen, but let's be thorough). */ if (len < insn_len) return paravirt_patch_default(type, clobber, ibuf, addr, len); @@ -1084,22 +1185,28 @@ static unsigned lguest_patch(u8 type, u16 clobber, void *ibuf, return insn_len; } -/*G:029 Once we get to lguest_init(), we know we're a Guest. The various +/*G:029 + * Once we get to lguest_init(), we know we're a Guest. The various * pv_ops structures in the kernel provide points for (almost) every routine we - * have to override to avoid privileged instructions. */ + * have to override to avoid privileged instructions. + */ __init void lguest_init(void) { - /* We're under lguest, paravirt is enabled, and we're running at - * privilege level 1, not 0 as normal. */ + /* We're under lguest. */ pv_info.name = "lguest"; + /* Paravirt is enabled. */ pv_info.paravirt_enabled = 1; + /* We're running at privilege level 1, not 0 as normal. */ pv_info.kernel_rpl = 1; + /* Everyone except Xen runs with this set. */ pv_info.shared_kernel_pmd = 1; - /* We set up all the lguest overrides for sensitive operations. These - * are detailed with the operations themselves. */ + /* + * We set up all the lguest overrides for sensitive operations. These + * are detailed with the operations themselves. + */ - /* interrupt-related operations */ + /* Interrupt-related operations */ pv_irq_ops.init_IRQ = lguest_init_IRQ; pv_irq_ops.save_fl = PV_CALLEE_SAVE(save_fl); pv_irq_ops.restore_fl = __PV_IS_CALLEE_SAVE(lg_restore_fl); @@ -1107,11 +1214,11 @@ __init void lguest_init(void) pv_irq_ops.irq_enable = __PV_IS_CALLEE_SAVE(lg_irq_enable); pv_irq_ops.safe_halt = lguest_safe_halt; - /* init-time operations */ + /* Setup operations */ pv_init_ops.memory_setup = lguest_memory_setup; pv_init_ops.patch = lguest_patch; - /* Intercepts of various cpu instructions */ + /* Intercepts of various CPU instructions */ pv_cpu_ops.load_gdt = lguest_load_gdt; pv_cpu_ops.cpuid = lguest_cpuid; pv_cpu_ops.load_idt = lguest_load_idt; @@ -1132,7 +1239,7 @@ __init void lguest_init(void) pv_cpu_ops.start_context_switch = paravirt_start_context_switch; pv_cpu_ops.end_context_switch = lguest_end_context_switch; - /* pagetable management */ + /* Pagetable management */ pv_mmu_ops.write_cr3 = lguest_write_cr3; pv_mmu_ops.flush_tlb_user = lguest_flush_tlb_user; pv_mmu_ops.flush_tlb_single = lguest_flush_tlb_single; @@ -1154,54 +1261,71 @@ __init void lguest_init(void) pv_mmu_ops.pte_update_defer = lguest_pte_update; #ifdef CONFIG_X86_LOCAL_APIC - /* apic read/write intercepts */ + /* APIC read/write intercepts */ set_lguest_basic_apic_ops(); #endif - /* time operations */ + /* Time operations */ pv_time_ops.get_wallclock = lguest_get_wallclock; pv_time_ops.time_init = lguest_time_init; pv_time_ops.get_tsc_khz = lguest_tsc_khz; - /* Now is a good time to look at the implementations of these functions - * before returning to the rest of lguest_init(). */ + /* + * Now is a good time to look at the implementations of these functions + * before returning to the rest of lguest_init(). + */ - /*G:070 Now we've seen all the paravirt_ops, we return to + /*G:070 + * Now we've seen all the paravirt_ops, we return to * lguest_init() where the rest of the fairly chaotic boot setup - * occurs. */ + * occurs. + */ - /* The stack protector is a weird thing where gcc places a canary + /* + * The stack protector is a weird thing where gcc places a canary * value on the stack and then checks it on return. This file is * compiled with -fno-stack-protector it, so we got this far without * problems. The value of the canary is kept at offset 20 from the * %gs register, so we need to set that up before calling C functions - * in other files. */ + * in other files. + */ setup_stack_canary_segment(0); - /* We could just call load_stack_canary_segment(), but we might as - * call switch_to_new_gdt() which loads the whole table and sets up - * the per-cpu segment descriptor register %fs as well. */ + + /* + * We could just call load_stack_canary_segment(), but we might as well + * call switch_to_new_gdt() which loads the whole table and sets up the + * per-cpu segment descriptor register %fs as well. + */ switch_to_new_gdt(0); /* As described in head_32.S, we map the first 128M of memory. */ max_pfn_mapped = (128*1024*1024) >> PAGE_SHIFT; - /* The Host<->Guest Switcher lives at the top of our address space, and + /* + * The Host<->Guest Switcher lives at the top of our address space, and * the Host told us how big it is when we made LGUEST_INIT hypercall: - * it put the answer in lguest_data.reserve_mem */ + * it put the answer in lguest_data.reserve_mem + */ reserve_top_address(lguest_data.reserve_mem); - /* If we don't initialize the lock dependency checker now, it crashes - * paravirt_disable_iospace. */ + /* + * If we don't initialize the lock dependency checker now, it crashes + * paravirt_disable_iospace. + */ lockdep_init(); - /* The IDE code spends about 3 seconds probing for disks: if we reserve + /* + * The IDE code spends about 3 seconds probing for disks: if we reserve * all the I/O ports up front it can't get them and so doesn't probe. * Other device drivers are similar (but less severe). This cuts the - * kernel boot time on my machine from 4.1 seconds to 0.45 seconds. */ + * kernel boot time on my machine from 4.1 seconds to 0.45 seconds. + */ paravirt_disable_iospace(); - /* This is messy CPU setup stuff which the native boot code does before - * start_kernel, so we have to do, too: */ + /* + * This is messy CPU setup stuff which the native boot code does before + * start_kernel, so we have to do, too: + */ cpu_detect(&new_cpu_data); /* head.S usually sets up the first capability word, so do it here. */ new_cpu_data.x86_capability[0] = cpuid_edx(1); @@ -1218,22 +1342,28 @@ __init void lguest_init(void) acpi_ht = 0; #endif - /* We set the preferred console to "hvc". This is the "hypervisor + /* + * We set the preferred console to "hvc". This is the "hypervisor * virtual console" driver written by the PowerPC people, which we also - * adapted for lguest's use. */ + * adapted for lguest's use. + */ add_preferred_console("hvc", 0, NULL); /* Register our very early console. */ virtio_cons_early_init(early_put_chars); - /* Last of all, we set the power management poweroff hook to point to + /* + * Last of all, we set the power management poweroff hook to point to * the Guest routine to power off, and the reboot hook to our restart - * routine. */ + * routine. + */ pm_power_off = lguest_power_off; machine_ops.restart = lguest_restart; - /* Now we're set up, call i386_start_kernel() in head32.c and we proceed - * to boot as normal. It never returns. */ + /* + * Now we're set up, call i386_start_kernel() in head32.c and we proceed + * to boot as normal. It never returns. + */ i386_start_kernel(); } /* diff --git a/arch/x86/lguest/i386_head.S b/arch/x86/lguest/i386_head.S index a9c8cfe61cd..db6aa95eb05 100644 --- a/arch/x86/lguest/i386_head.S +++ b/arch/x86/lguest/i386_head.S @@ -5,7 +5,8 @@ #include #include -/*G:020 Our story starts with the kernel booting into startup_32 in +/*G:020 + * Our story starts with the kernel booting into startup_32 in * arch/x86/kernel/head_32.S. It expects a boot header, which is created by * the bootloader (the Launcher in our case). * @@ -21,11 +22,14 @@ * data without remembering to subtract __PAGE_OFFSET! * * The .section line puts this code in .init.text so it will be discarded after - * boot. */ + * boot. + */ .section .init.text, "ax", @progbits ENTRY(lguest_entry) - /* We make the "initialization" hypercall now to tell the Host about - * us, and also find out where it put our page tables. */ + /* + * We make the "initialization" hypercall now to tell the Host about + * us, and also find out where it put our page tables. + */ movl $LHCALL_LGUEST_INIT, %eax movl $lguest_data - __PAGE_OFFSET, %ebx .byte 0x0f,0x01,0xc1 /* KVM_HYPERCALL */ @@ -33,13 +37,14 @@ ENTRY(lguest_entry) /* Set up the initial stack so we can run C code. */ movl $(init_thread_union+THREAD_SIZE),%esp - /* Jumps are relative, and we're running __PAGE_OFFSET too low at the - * moment. */ + /* Jumps are relative: we're running __PAGE_OFFSET too low. */ jmp lguest_init+__PAGE_OFFSET -/*G:055 We create a macro which puts the assembler code between lgstart_ and - * lgend_ markers. These templates are put in the .text section: they can't be - * discarded after boot as we may need to patch modules, too. */ +/*G:055 + * We create a macro which puts the assembler code between lgstart_ and lgend_ + * markers. These templates are put in the .text section: they can't be + * discarded after boot as we may need to patch modules, too. + */ .text #define LGUEST_PATCH(name, insns...) \ lgstart_##name: insns; lgend_##name:; \ @@ -48,58 +53,74 @@ ENTRY(lguest_entry) LGUEST_PATCH(cli, movl $0, lguest_data+LGUEST_DATA_irq_enabled) LGUEST_PATCH(pushf, movl lguest_data+LGUEST_DATA_irq_enabled, %eax) -/*G:033 But using those wrappers is inefficient (we'll see why that doesn't - * matter for save_fl and irq_disable later). If we write our routines - * carefully in assembler, we can avoid clobbering any registers and avoid - * jumping through the wrapper functions. +/*G:033 + * But using those wrappers is inefficient (we'll see why that doesn't matter + * for save_fl and irq_disable later). If we write our routines carefully in + * assembler, we can avoid clobbering any registers and avoid jumping through + * the wrapper functions. * * I skipped over our first piece of assembler, but this one is worth studying - * in a bit more detail so I'll describe in easy stages. First, the routine - * to enable interrupts: */ + * in a bit more detail so I'll describe in easy stages. First, the routine to + * enable interrupts: + */ ENTRY(lg_irq_enable) - /* The reverse of irq_disable, this sets lguest_data.irq_enabled to - * X86_EFLAGS_IF (ie. "Interrupts enabled"). */ + /* + * The reverse of irq_disable, this sets lguest_data.irq_enabled to + * X86_EFLAGS_IF (ie. "Interrupts enabled"). + */ movl $X86_EFLAGS_IF, lguest_data+LGUEST_DATA_irq_enabled - /* But now we need to check if the Host wants to know: there might have + /* + * But now we need to check if the Host wants to know: there might have * been interrupts waiting to be delivered, in which case it will have * set lguest_data.irq_pending to X86_EFLAGS_IF. If it's not zero, we - * jump to send_interrupts, otherwise we're done. */ + * jump to send_interrupts, otherwise we're done. + */ testl $0, lguest_data+LGUEST_DATA_irq_pending jnz send_interrupts - /* One cool thing about x86 is that you can do many things without using + /* + * One cool thing about x86 is that you can do many things without using * a register. In this case, the normal path hasn't needed to save or - * restore any registers at all! */ + * restore any registers at all! + */ ret send_interrupts: - /* OK, now we need a register: eax is used for the hypercall number, + /* + * OK, now we need a register: eax is used for the hypercall number, * which is LHCALL_SEND_INTERRUPTS. * * We used not to bother with this pending detection at all, which was * much simpler. Sooner or later the Host would realize it had to * send us an interrupt. But that turns out to make performance 7 * times worse on a simple tcp benchmark. So now we do this the hard - * way. */ + * way. + */ pushl %eax movl $LHCALL_SEND_INTERRUPTS, %eax - /* This is a vmcall instruction (same thing that KVM uses). Older + /* + * This is a vmcall instruction (same thing that KVM uses). Older * assembler versions might not know the "vmcall" instruction, so we - * create one manually here. */ + * create one manually here. + */ .byte 0x0f,0x01,0xc1 /* KVM_HYPERCALL */ popl %eax ret -/* Finally, the "popf" or "restore flags" routine. The %eax register holds the +/* + * Finally, the "popf" or "restore flags" routine. The %eax register holds the * flags (in practice, either X86_EFLAGS_IF or 0): if it's X86_EFLAGS_IF we're - * enabling interrupts again, if it's 0 we're leaving them off. */ + * enabling interrupts again, if it's 0 we're leaving them off. + */ ENTRY(lg_restore_fl) /* This is just "lguest_data.irq_enabled = flags;" */ movl %eax, lguest_data+LGUEST_DATA_irq_enabled - /* Now, if the %eax value has enabled interrupts and + /* + * Now, if the %eax value has enabled interrupts and * lguest_data.irq_pending is set, we want to tell the Host so it can * deliver any outstanding interrupts. Fortunately, both values will * be X86_EFLAGS_IF (ie. 512) in that case, and the "testl" * instruction will AND them together for us. If both are set, we - * jump to send_interrupts. */ + * jump to send_interrupts. + */ testl lguest_data+LGUEST_DATA_irq_pending, %eax jnz send_interrupts /* Again, the normal path has used no extra registers. Clever, huh? */ @@ -109,22 +130,24 @@ ENTRY(lg_restore_fl) .global lguest_noirq_start .global lguest_noirq_end -/*M:004 When the Host reflects a trap or injects an interrupt into the Guest, - * it sets the eflags interrupt bit on the stack based on - * lguest_data.irq_enabled, so the Guest iret logic does the right thing when - * restoring it. However, when the Host sets the Guest up for direct traps, - * such as system calls, the processor is the one to push eflags onto the - * stack, and the interrupt bit will be 1 (in reality, interrupts are always - * enabled in the Guest). +/*M:004 + * When the Host reflects a trap or injects an interrupt into the Guest, it + * sets the eflags interrupt bit on the stack based on lguest_data.irq_enabled, + * so the Guest iret logic does the right thing when restoring it. However, + * when the Host sets the Guest up for direct traps, such as system calls, the + * processor is the one to push eflags onto the stack, and the interrupt bit + * will be 1 (in reality, interrupts are always enabled in the Guest). * * This turns out to be harmless: the only trap which should happen under Linux * with interrupts disabled is Page Fault (due to our lazy mapping of vmalloc * regions), which has to be reflected through the Host anyway. If another * trap *does* go off when interrupts are disabled, the Guest will panic, and - * we'll never get to this iret! :*/ + * we'll never get to this iret! +:*/ -/*G:045 There is one final paravirt_op that the Guest implements, and glancing - * at it you can see why I left it to last. It's *cool*! It's in *assembler*! +/*G:045 + * There is one final paravirt_op that the Guest implements, and glancing at it + * you can see why I left it to last. It's *cool*! It's in *assembler*! * * The "iret" instruction is used to return from an interrupt or trap. The * stack looks like this: @@ -148,15 +171,18 @@ ENTRY(lg_restore_fl) * return to userspace or wherever. Our solution to this is to surround the * code with lguest_noirq_start: and lguest_noirq_end: labels. We tell the * Host that it is *never* to interrupt us there, even if interrupts seem to be - * enabled. */ + * enabled. + */ ENTRY(lguest_iret) pushl %eax movl 12(%esp), %eax lguest_noirq_start: - /* Note the %ss: segment prefix here. Normal data accesses use the + /* + * Note the %ss: segment prefix here. Normal data accesses use the * "ds" segment, but that will have already been restored for whatever * we're returning to (such as userspace): we can't trust it. The %ss: - * prefix makes sure we use the stack segment, which is still valid. */ + * prefix makes sure we use the stack segment, which is still valid. + */ movl %eax,%ss:lguest_data+LGUEST_DATA_irq_enabled popl %eax iret diff --git a/drivers/lguest/core.c b/drivers/lguest/core.c index a6974e9b8eb..cd058bc903f 100644 --- a/drivers/lguest/core.c +++ b/drivers/lguest/core.c @@ -1,6 +1,8 @@ -/*P:400 This contains run_guest() which actually calls into the Host<->Guest +/*P:400 + * This contains run_guest() which actually calls into the Host<->Guest * Switcher and analyzes the return, such as determining if the Guest wants the - * Host to do something. This file also contains useful helper routines. :*/ + * Host to do something. This file also contains useful helper routines. +:*/ #include #include #include @@ -24,7 +26,8 @@ static struct page **switcher_page; /* This One Big lock protects all inter-guest data structures. */ DEFINE_MUTEX(lguest_lock); -/*H:010 We need to set up the Switcher at a high virtual address. Remember the +/*H:010 + * We need to set up the Switcher at a high virtual address. Remember the * Switcher is a few hundred bytes of assembler code which actually changes the * CPU to run the Guest, and then changes back to the Host when a trap or * interrupt happens. @@ -33,7 +36,8 @@ DEFINE_MUTEX(lguest_lock); * Host since it will be running as the switchover occurs. * * Trying to map memory at a particular address is an unusual thing to do, so - * it's not a simple one-liner. */ + * it's not a simple one-liner. + */ static __init int map_switcher(void) { int i, err; @@ -47,8 +51,10 @@ static __init int map_switcher(void) * easy. */ - /* We allocate an array of struct page pointers. map_vm_area() wants - * this, rather than just an array of pages. */ + /* + * We allocate an array of struct page pointers. map_vm_area() wants + * this, rather than just an array of pages. + */ switcher_page = kmalloc(sizeof(switcher_page[0])*TOTAL_SWITCHER_PAGES, GFP_KERNEL); if (!switcher_page) { @@ -56,8 +62,10 @@ static __init int map_switcher(void) goto out; } - /* Now we actually allocate the pages. The Guest will see these pages, - * so we make sure they're zeroed. */ + /* + * Now we actually allocate the pages. The Guest will see these pages, + * so we make sure they're zeroed. + */ for (i = 0; i < TOTAL_SWITCHER_PAGES; i++) { unsigned long addr = get_zeroed_page(GFP_KERNEL); if (!addr) { @@ -67,19 +75,23 @@ static __init int map_switcher(void) switcher_page[i] = virt_to_page(addr); } - /* First we check that the Switcher won't overlap the fixmap area at + /* + * First we check that the Switcher won't overlap the fixmap area at * the top of memory. It's currently nowhere near, but it could have - * very strange effects if it ever happened. */ + * very strange effects if it ever happened. + */ if (SWITCHER_ADDR + (TOTAL_SWITCHER_PAGES+1)*PAGE_SIZE > FIXADDR_START){ err = -ENOMEM; printk("lguest: mapping switcher would thwack fixmap\n"); goto free_pages; } - /* Now we reserve the "virtual memory area" we want: 0xFFC00000 + /* + * Now we reserve the "virtual memory area" we want: 0xFFC00000 * (SWITCHER_ADDR). We might not get it in theory, but in practice * it's worked so far. The end address needs +1 because __get_vm_area - * allocates an extra guard page, so we need space for that. */ + * allocates an extra guard page, so we need space for that. + */ switcher_vma = __get_vm_area(TOTAL_SWITCHER_PAGES * PAGE_SIZE, VM_ALLOC, SWITCHER_ADDR, SWITCHER_ADDR + (TOTAL_SWITCHER_PAGES+1) * PAGE_SIZE); @@ -89,11 +101,13 @@ static __init int map_switcher(void) goto free_pages; } - /* This code actually sets up the pages we've allocated to appear at + /* + * This code actually sets up the pages we've allocated to appear at * SWITCHER_ADDR. map_vm_area() takes the vma we allocated above, the * kind of pages we're mapping (kernel pages), and a pointer to our * array of struct pages. It increments that pointer, but we don't - * care. */ + * care. + */ pagep = switcher_page; err = map_vm_area(switcher_vma, PAGE_KERNEL_EXEC, &pagep); if (err) { @@ -101,8 +115,10 @@ static __init int map_switcher(void) goto free_vma; } - /* Now the Switcher is mapped at the right address, we can't fail! - * Copy in the compiled-in Switcher code (from _switcher.S). */ + /* + * Now the Switcher is mapped at the right address, we can't fail! + * Copy in the compiled-in Switcher code (from _switcher.S). + */ memcpy(switcher_vma->addr, start_switcher_text, end_switcher_text - start_switcher_text); @@ -124,8 +140,7 @@ out: } /*:*/ -/* Cleaning up the mapping when the module is unloaded is almost... - * too easy. */ +/* Cleaning up the mapping when the module is unloaded is almost... too easy. */ static void unmap_switcher(void) { unsigned int i; @@ -151,16 +166,19 @@ static void unmap_switcher(void) * But we can't trust the Guest: it might be trying to access the Launcher * code. We have to check that the range is below the pfn_limit the Launcher * gave us. We have to make sure that addr + len doesn't give us a false - * positive by overflowing, too. */ + * positive by overflowing, too. + */ bool lguest_address_ok(const struct lguest *lg, unsigned long addr, unsigned long len) { return (addr+len) / PAGE_SIZE < lg->pfn_limit && (addr+len >= addr); } -/* This routine copies memory from the Guest. Here we can see how useful the +/* + * This routine copies memory from the Guest. Here we can see how useful the * kill_lguest() routine we met in the Launcher can be: we return a random - * value (all zeroes) instead of needing to return an error. */ + * value (all zeroes) instead of needing to return an error. + */ void __lgread(struct lg_cpu *cpu, void *b, unsigned long addr, unsigned bytes) { if (!lguest_address_ok(cpu->lg, addr, bytes) @@ -181,9 +199,11 @@ void __lgwrite(struct lg_cpu *cpu, unsigned long addr, const void *b, } /*:*/ -/*H:030 Let's jump straight to the the main loop which runs the Guest. +/*H:030 + * Let's jump straight to the the main loop which runs the Guest. * Remember, this is called by the Launcher reading /dev/lguest, and we keep - * going around and around until something interesting happens. */ + * going around and around until something interesting happens. + */ int run_guest(struct lg_cpu *cpu, unsigned long __user *user) { /* We stop running once the Guest is dead. */ @@ -195,8 +215,10 @@ int run_guest(struct lg_cpu *cpu, unsigned long __user *user) if (cpu->hcall) do_hypercalls(cpu); - /* It's possible the Guest did a NOTIFY hypercall to the - * Launcher, in which case we return from the read() now. */ + /* + * It's possible the Guest did a NOTIFY hypercall to the + * Launcher, in which case we return from the read() now. + */ if (cpu->pending_notify) { if (!send_notify_to_eventfd(cpu)) { if (put_user(cpu->pending_notify, user)) @@ -209,29 +231,39 @@ int run_guest(struct lg_cpu *cpu, unsigned long __user *user) if (signal_pending(current)) return -ERESTARTSYS; - /* Check if there are any interrupts which can be delivered now: + /* + * Check if there are any interrupts which can be delivered now: * if so, this sets up the hander to be executed when we next - * run the Guest. */ + * run the Guest. + */ irq = interrupt_pending(cpu, &more); if (irq < LGUEST_IRQS) try_deliver_interrupt(cpu, irq, more); - /* All long-lived kernel loops need to check with this horrible + /* + * All long-lived kernel loops need to check with this horrible * thing called the freezer. If the Host is trying to suspend, - * it stops us. */ + * it stops us. + */ try_to_freeze(); - /* Just make absolutely sure the Guest is still alive. One of - * those hypercalls could have been fatal, for example. */ + /* + * Just make absolutely sure the Guest is still alive. One of + * those hypercalls could have been fatal, for example. + */ if (cpu->lg->dead) break; - /* If the Guest asked to be stopped, we sleep. The Guest's - * clock timer will wake us. */ + /* + * If the Guest asked to be stopped, we sleep. The Guest's + * clock timer will wake us. + */ if (cpu->halted) { set_current_state(TASK_INTERRUPTIBLE); - /* Just before we sleep, make sure no interrupt snuck in - * which we should be doing. */ + /* + * Just before we sleep, make sure no interrupt snuck in + * which we should be doing. + */ if (interrupt_pending(cpu, &more) < LGUEST_IRQS) set_current_state(TASK_RUNNING); else @@ -239,8 +271,10 @@ int run_guest(struct lg_cpu *cpu, unsigned long __user *user) continue; } - /* OK, now we're ready to jump into the Guest. First we put up - * the "Do Not Disturb" sign: */ + /* + * OK, now we're ready to jump into the Guest. First we put up + * the "Do Not Disturb" sign: + */ local_irq_disable(); /* Actually run the Guest until something happens. */ @@ -327,8 +361,10 @@ static void __exit fini(void) } /*:*/ -/* The Host side of lguest can be a module. This is a nice way for people to - * play with it. */ +/* + * The Host side of lguest can be a module. This is a nice way for people to + * play with it. + */ module_init(init); module_exit(fini); MODULE_LICENSE("GPL"); diff --git a/drivers/lguest/hypercalls.c b/drivers/lguest/hypercalls.c index c29ffa19cb7..787ab4bc09f 100644 --- a/drivers/lguest/hypercalls.c +++ b/drivers/lguest/hypercalls.c @@ -1,8 +1,10 @@ -/*P:500 Just as userspace programs request kernel operations through a system +/*P:500 + * Just as userspace programs request kernel operations through a system * call, the Guest requests Host operations through a "hypercall". You might * notice this nomenclature doesn't really follow any logic, but the name has * been around for long enough that we're stuck with it. As you'd expect, this - * code is basically a one big switch statement. :*/ + * code is basically a one big switch statement. +:*/ /* Copyright (C) 2006 Rusty Russell IBM Corporation @@ -28,30 +30,41 @@ #include #include "lg.h" -/*H:120 This is the core hypercall routine: where the Guest gets what it wants. - * Or gets killed. Or, in the case of LHCALL_SHUTDOWN, both. */ +/*H:120 + * This is the core hypercall routine: where the Guest gets what it wants. + * Or gets killed. Or, in the case of LHCALL_SHUTDOWN, both. + */ static void do_hcall(struct lg_cpu *cpu, struct hcall_args *args) { switch (args->arg0) { case LHCALL_FLUSH_ASYNC: - /* This call does nothing, except by breaking out of the Guest - * it makes us process all the asynchronous hypercalls. */ + /* + * This call does nothing, except by breaking out of the Guest + * it makes us process all the asynchronous hypercalls. + */ break; case LHCALL_SEND_INTERRUPTS: - /* This call does nothing too, but by breaking out of the Guest - * it makes us process any pending interrupts. */ + /* + * This call does nothing too, but by breaking out of the Guest + * it makes us process any pending interrupts. + */ break; case LHCALL_LGUEST_INIT: - /* You can't get here unless you're already initialized. Don't - * do that. */ + /* + * You can't get here unless you're already initialized. Don't + * do that. + */ kill_guest(cpu, "already have lguest_data"); break; case LHCALL_SHUTDOWN: { - /* Shutdown is such a trivial hypercall that we do it in four - * lines right here. */ char msg[128]; - /* If the lgread fails, it will call kill_guest() itself; the - * kill_guest() with the message will be ignored. */ + /* + * Shutdown is such a trivial hypercall that we do it in four + * lines right here. + * + * If the lgread fails, it will call kill_guest() itself; the + * kill_guest() with the message will be ignored. + */ __lgread(cpu, msg, args->arg1, sizeof(msg)); msg[sizeof(msg)-1] = '\0'; kill_guest(cpu, "CRASH: %s", msg); @@ -60,16 +73,17 @@ static void do_hcall(struct lg_cpu *cpu, struct hcall_args *args) break; } case LHCALL_FLUSH_TLB: - /* FLUSH_TLB comes in two flavors, depending on the - * argument: */ + /* FLUSH_TLB comes in two flavors, depending on the argument: */ if (args->arg1) guest_pagetable_clear_all(cpu); else guest_pagetable_flush_user(cpu); break; - /* All these calls simply pass the arguments through to the right - * routines. */ + /* + * All these calls simply pass the arguments through to the right + * routines. + */ case LHCALL_NEW_PGTABLE: guest_new_pagetable(cpu, args->arg1); break; @@ -112,15 +126,16 @@ static void do_hcall(struct lg_cpu *cpu, struct hcall_args *args) kill_guest(cpu, "Bad hypercall %li\n", args->arg0); } } -/*:*/ -/*H:124 Asynchronous hypercalls are easy: we just look in the array in the +/*H:124 + * Asynchronous hypercalls are easy: we just look in the array in the * Guest's "struct lguest_data" to see if any new ones are marked "ready". * * We are careful to do these in order: obviously we respect the order the * Guest put them in the ring, but we also promise the Guest that they will * happen before any normal hypercall (which is why we check this before - * checking for a normal hcall). */ + * checking for a normal hcall). + */ static void do_async_hcalls(struct lg_cpu *cpu) { unsigned int i; @@ -133,22 +148,28 @@ static void do_async_hcalls(struct lg_cpu *cpu) /* We process "struct lguest_data"s hcalls[] ring once. */ for (i = 0; i < ARRAY_SIZE(st); i++) { struct hcall_args args; - /* We remember where we were up to from last time. This makes + /* + * We remember where we were up to from last time. This makes * sure that the hypercalls are done in the order the Guest - * places them in the ring. */ + * places them in the ring. + */ unsigned int n = cpu->next_hcall; /* 0xFF means there's no call here (yet). */ if (st[n] == 0xFF) break; - /* OK, we have hypercall. Increment the "next_hcall" cursor, - * and wrap back to 0 if we reach the end. */ + /* + * OK, we have hypercall. Increment the "next_hcall" cursor, + * and wrap back to 0 if we reach the end. + */ if (++cpu->next_hcall == LHCALL_RING_SIZE) cpu->next_hcall = 0; - /* Copy the hypercall arguments into a local copy of - * the hcall_args struct. */ + /* + * Copy the hypercall arguments into a local copy of the + * hcall_args struct. + */ if (copy_from_user(&args, &cpu->lg->lguest_data->hcalls[n], sizeof(struct hcall_args))) { kill_guest(cpu, "Fetching async hypercalls"); @@ -164,19 +185,25 @@ static void do_async_hcalls(struct lg_cpu *cpu) break; } - /* Stop doing hypercalls if they want to notify the Launcher: - * it needs to service this first. */ + /* + * Stop doing hypercalls if they want to notify the Launcher: + * it needs to service this first. + */ if (cpu->pending_notify) break; } } -/* Last of all, we look at what happens first of all. The very first time the - * Guest makes a hypercall, we end up here to set things up: */ +/* + * Last of all, we look at what happens first of all. The very first time the + * Guest makes a hypercall, we end up here to set things up: + */ static void initialize(struct lg_cpu *cpu) { - /* You can't do anything until you're initialized. The Guest knows the - * rules, so we're unforgiving here. */ + /* + * You can't do anything until you're initialized. The Guest knows the + * rules, so we're unforgiving here. + */ if (cpu->hcall->arg0 != LHCALL_LGUEST_INIT) { kill_guest(cpu, "hypercall %li before INIT", cpu->hcall->arg0); return; @@ -185,32 +212,40 @@ static void initialize(struct lg_cpu *cpu) if (lguest_arch_init_hypercalls(cpu)) kill_guest(cpu, "bad guest page %p", cpu->lg->lguest_data); - /* The Guest tells us where we're not to deliver interrupts by putting - * the range of addresses into "struct lguest_data". */ + /* + * The Guest tells us where we're not to deliver interrupts by putting + * the range of addresses into "struct lguest_data". + */ if (get_user(cpu->lg->noirq_start, &cpu->lg->lguest_data->noirq_start) || get_user(cpu->lg->noirq_end, &cpu->lg->lguest_data->noirq_end)) kill_guest(cpu, "bad guest page %p", cpu->lg->lguest_data); - /* We write the current time into the Guest's data page once so it can - * set its clock. */ + /* + * We write the current time into the Guest's data page once so it can + * set its clock. + */ write_timestamp(cpu); /* page_tables.c will also do some setup. */ page_table_guest_data_init(cpu); - /* This is the one case where the above accesses might have been the + /* + * This is the one case where the above accesses might have been the * first write to a Guest page. This may have caused a copy-on-write * fault, but the old page might be (read-only) in the Guest - * pagetable. */ + * pagetable. + */ guest_pagetable_clear_all(cpu); } /*:*/ -/*M:013 If a Guest reads from a page (so creates a mapping) that it has never +/*M:013 + * If a Guest reads from a page (so creates a mapping) that it has never * written to, and then the Launcher writes to it (ie. the output of a virtual * device), the Guest will still see the old page. In practice, this never * happens: why would the Guest read a page which it has never written to? But - * a similar scenario might one day bite us, so it's worth mentioning. :*/ + * a similar scenario might one day bite us, so it's worth mentioning. +:*/ /*H:100 * Hypercalls @@ -229,17 +264,22 @@ void do_hypercalls(struct lg_cpu *cpu) return; } - /* The Guest has initialized. + /* + * The Guest has initialized. * - * Look in the hypercall ring for the async hypercalls: */ + * Look in the hypercall ring for the async hypercalls: + */ do_async_hcalls(cpu); - /* If we stopped reading the hypercall ring because the Guest did a + /* + * If we stopped reading the hypercall ring because the Guest did a * NOTIFY to the Launcher, we want to return now. Otherwise we do - * the hypercall. */ + * the hypercall. + */ if (!cpu->pending_notify) { do_hcall(cpu, cpu->hcall); - /* Tricky point: we reset the hcall pointer to mark the + /* + * Tricky point: we reset the hcall pointer to mark the * hypercall as "done". We use the hcall pointer rather than * the trap number to indicate a hypercall is pending. * Normally it doesn't matter: the Guest will run again and @@ -248,13 +288,16 @@ void do_hypercalls(struct lg_cpu *cpu) * However, if we are signalled or the Guest sends I/O to the * Launcher, the run_guest() loop will exit without running the * Guest. When it comes back it would try to re-run the - * hypercall. Finding that bug sucked. */ + * hypercall. Finding that bug sucked. + */ cpu->hcall = NULL; } } -/* This routine supplies the Guest with time: it's used for wallclock time at - * initial boot and as a rough time source if the TSC isn't available. */ +/* + * This routine supplies the Guest with time: it's used for wallclock time at + * initial boot and as a rough time source if the TSC isn't available. + */ void write_timestamp(struct lg_cpu *cpu) { struct timespec now; diff --git a/drivers/lguest/interrupts_and_traps.c b/drivers/lguest/interrupts_and_traps.c index 0e9067b0d50..18648180db0 100644 --- a/drivers/lguest/interrupts_and_traps.c +++ b/drivers/lguest/interrupts_and_traps.c @@ -1,4 +1,5 @@ -/*P:800 Interrupts (traps) are complicated enough to earn their own file. +/*P:800 + * Interrupts (traps) are complicated enough to earn their own file. * There are three classes of interrupts: * * 1) Real hardware interrupts which occur while we're running the Guest, @@ -10,7 +11,8 @@ * just like real hardware would deliver them. Traps from the Guest can be set * up to go directly back into the Guest, but sometimes the Host wants to see * them first, so we also have a way of "reflecting" them into the Guest as if - * they had been delivered to it directly. :*/ + * they had been delivered to it directly. +:*/ #include #include #include @@ -26,8 +28,10 @@ static unsigned long idt_address(u32 lo, u32 hi) return (lo & 0x0000FFFF) | (hi & 0xFFFF0000); } -/* The "type" of the interrupt handler is a 4 bit field: we only support a - * couple of types. */ +/* + * The "type" of the interrupt handler is a 4 bit field: we only support a + * couple of types. + */ static int idt_type(u32 lo, u32 hi) { return (hi >> 8) & 0xF; @@ -39,8 +43,10 @@ static bool idt_present(u32 lo, u32 hi) return (hi & 0x8000); } -/* We need a helper to "push" a value onto the Guest's stack, since that's a - * big part of what delivering an interrupt does. */ +/* + * We need a helper to "push" a value onto the Guest's stack, since that's a + * big part of what delivering an interrupt does. + */ static void push_guest_stack(struct lg_cpu *cpu, unsigned long *gstack, u32 val) { /* Stack grows upwards: move stack then write value. */ @@ -48,7 +54,8 @@ static void push_guest_stack(struct lg_cpu *cpu, unsigned long *gstack, u32 val) lgwrite(cpu, *gstack, u32, val); } -/*H:210 The set_guest_interrupt() routine actually delivers the interrupt or +/*H:210 + * The set_guest_interrupt() routine actually delivers the interrupt or * trap. The mechanics of delivering traps and interrupts to the Guest are the * same, except some traps have an "error code" which gets pushed onto the * stack as well: the caller tells us if this is one. @@ -59,7 +66,8 @@ static void push_guest_stack(struct lg_cpu *cpu, unsigned long *gstack, u32 val) * * We set up the stack just like the CPU does for a real interrupt, so it's * identical for the Guest (and the standard "iret" instruction will undo - * it). */ + * it). + */ static void set_guest_interrupt(struct lg_cpu *cpu, u32 lo, u32 hi, bool has_err) { @@ -67,20 +75,26 @@ static void set_guest_interrupt(struct lg_cpu *cpu, u32 lo, u32 hi, u32 eflags, ss, irq_enable; unsigned long virtstack; - /* There are two cases for interrupts: one where the Guest is already + /* + * There are two cases for interrupts: one where the Guest is already * in the kernel, and a more complex one where the Guest is in - * userspace. We check the privilege level to find out. */ + * userspace. We check the privilege level to find out. + */ if ((cpu->regs->ss&0x3) != GUEST_PL) { - /* The Guest told us their kernel stack with the SET_STACK - * hypercall: both the virtual address and the segment */ + /* + * The Guest told us their kernel stack with the SET_STACK + * hypercall: both the virtual address and the segment. + */ virtstack = cpu->esp1; ss = cpu->ss1; origstack = gstack = guest_pa(cpu, virtstack); - /* We push the old stack segment and pointer onto the new + /* + * We push the old stack segment and pointer onto the new * stack: when the Guest does an "iret" back from the interrupt * handler the CPU will notice they're dropping privilege - * levels and expect these here. */ + * levels and expect these here. + */ push_guest_stack(cpu, &gstack, cpu->regs->ss); push_guest_stack(cpu, &gstack, cpu->regs->esp); } else { @@ -91,18 +105,22 @@ static void set_guest_interrupt(struct lg_cpu *cpu, u32 lo, u32 hi, origstack = gstack = guest_pa(cpu, virtstack); } - /* Remember that we never let the Guest actually disable interrupts, so + /* + * Remember that we never let the Guest actually disable interrupts, so * the "Interrupt Flag" bit is always set. We copy that bit from the * Guest's "irq_enabled" field into the eflags word: we saw the Guest - * copy it back in "lguest_iret". */ + * copy it back in "lguest_iret". + */ eflags = cpu->regs->eflags; if (get_user(irq_enable, &cpu->lg->lguest_data->irq_enabled) == 0 && !(irq_enable & X86_EFLAGS_IF)) eflags &= ~X86_EFLAGS_IF; - /* An interrupt is expected to push three things on the stack: the old + /* + * An interrupt is expected to push three things on the stack: the old * "eflags" word, the old code segment, and the old instruction - * pointer. */ + * pointer. + */ push_guest_stack(cpu, &gstack, eflags); push_guest_stack(cpu, &gstack, cpu->regs->cs); push_guest_stack(cpu, &gstack, cpu->regs->eip); @@ -111,15 +129,19 @@ static void set_guest_interrupt(struct lg_cpu *cpu, u32 lo, u32 hi, if (has_err) push_guest_stack(cpu, &gstack, cpu->regs->errcode); - /* Now we've pushed all the old state, we change the stack, the code - * segment and the address to execute. */ + /* + * Now we've pushed all the old state, we change the stack, the code + * segment and the address to execute. + */ cpu->regs->ss = ss; cpu->regs->esp = virtstack + (gstack - origstack); cpu->regs->cs = (__KERNEL_CS|GUEST_PL); cpu->regs->eip = idt_address(lo, hi); - /* There are two kinds of interrupt handlers: 0xE is an "interrupt - * gate" which expects interrupts to be disabled on entry. */ + /* + * There are two kinds of interrupt handlers: 0xE is an "interrupt + * gate" which expects interrupts to be disabled on entry. + */ if (idt_type(lo, hi) == 0xE) if (put_user(0, &cpu->lg->lguest_data->irq_enabled)) kill_guest(cpu, "Disabling interrupts"); @@ -130,7 +152,8 @@ static void set_guest_interrupt(struct lg_cpu *cpu, u32 lo, u32 hi, * * interrupt_pending() returns the first pending interrupt which isn't blocked * by the Guest. It is called before every entry to the Guest, and just before - * we go to sleep when the Guest has halted itself. */ + * we go to sleep when the Guest has halted itself. + */ unsigned int interrupt_pending(struct lg_cpu *cpu, bool *more) { unsigned int irq; @@ -140,8 +163,10 @@ unsigned int interrupt_pending(struct lg_cpu *cpu, bool *more) if (!cpu->lg->lguest_data) return LGUEST_IRQS; - /* Take our "irqs_pending" array and remove any interrupts the Guest - * wants blocked: the result ends up in "blk". */ + /* + * Take our "irqs_pending" array and remove any interrupts the Guest + * wants blocked: the result ends up in "blk". + */ if (copy_from_user(&blk, cpu->lg->lguest_data->blocked_interrupts, sizeof(blk))) return LGUEST_IRQS; @@ -154,16 +179,20 @@ unsigned int interrupt_pending(struct lg_cpu *cpu, bool *more) return irq; } -/* This actually diverts the Guest to running an interrupt handler, once an - * interrupt has been identified by interrupt_pending(). */ +/* + * This actually diverts the Guest to running an interrupt handler, once an + * interrupt has been identified by interrupt_pending(). + */ void try_deliver_interrupt(struct lg_cpu *cpu, unsigned int irq, bool more) { struct desc_struct *idt; BUG_ON(irq >= LGUEST_IRQS); - /* They may be in the middle of an iret, where they asked us never to - * deliver interrupts. */ + /* + * They may be in the middle of an iret, where they asked us never to + * deliver interrupts. + */ if (cpu->regs->eip >= cpu->lg->noirq_start && (cpu->regs->eip < cpu->lg->noirq_end)) return; @@ -187,29 +216,37 @@ void try_deliver_interrupt(struct lg_cpu *cpu, unsigned int irq, bool more) } } - /* Look at the IDT entry the Guest gave us for this interrupt. The + /* + * Look at the IDT entry the Guest gave us for this interrupt. The * first 32 (FIRST_EXTERNAL_VECTOR) entries are for traps, so we skip - * over them. */ + * over them. + */ idt = &cpu->arch.idt[FIRST_EXTERNAL_VECTOR+irq]; /* If they don't have a handler (yet?), we just ignore it */ if (idt_present(idt->a, idt->b)) { /* OK, mark it no longer pending and deliver it. */ clear_bit(irq, cpu->irqs_pending); - /* set_guest_interrupt() takes the interrupt descriptor and a + /* + * set_guest_interrupt() takes the interrupt descriptor and a * flag to say whether this interrupt pushes an error code onto - * the stack as well: virtual interrupts never do. */ + * the stack as well: virtual interrupts never do. + */ set_guest_interrupt(cpu, idt->a, idt->b, false); } - /* Every time we deliver an interrupt, we update the timestamp in the + /* + * Every time we deliver an interrupt, we update the timestamp in the * Guest's lguest_data struct. It would be better for the Guest if we * did this more often, but it can actually be quite slow: doing it * here is a compromise which means at least it gets updated every - * timer interrupt. */ + * timer interrupt. + */ write_timestamp(cpu); - /* If there are no other interrupts we want to deliver, clear - * the pending flag. */ + /* + * If there are no other interrupts we want to deliver, clear + * the pending flag. + */ if (!more) put_user(0, &cpu->lg->lguest_data->irq_pending); } @@ -217,24 +254,29 @@ void try_deliver_interrupt(struct lg_cpu *cpu, unsigned int irq, bool more) /* And this is the routine when we want to set an interrupt for the Guest. */ void set_interrupt(struct lg_cpu *cpu, unsigned int irq) { - /* Next time the Guest runs, the core code will see if it can deliver - * this interrupt. */ + /* + * Next time the Guest runs, the core code will see if it can deliver + * this interrupt. + */ set_bit(irq, cpu->irqs_pending); - /* Make sure it sees it; it might be asleep (eg. halted), or - * running the Guest right now, in which case kick_process() - * will knock it out. */ + /* + * Make sure it sees it; it might be asleep (eg. halted), or running + * the Guest right now, in which case kick_process() will knock it out. + */ if (!wake_up_process(cpu->tsk)) kick_process(cpu->tsk); } /*:*/ -/* Linux uses trap 128 for system calls. Plan9 uses 64, and Ron Minnich sent +/* + * Linux uses trap 128 for system calls. Plan9 uses 64, and Ron Minnich sent * me a patch, so we support that too. It'd be a big step for lguest if half * the Plan 9 user base were to start using it. * * Actually now I think of it, it's possible that Ron *is* half the Plan 9 - * userbase. Oh well. */ + * userbase. Oh well. + */ static bool could_be_syscall(unsigned int num) { /* Normal Linux SYSCALL_VECTOR or reserved vector? */ @@ -274,9 +316,11 @@ void free_interrupts(void) clear_bit(syscall_vector, used_vectors); } -/*H:220 Now we've got the routines to deliver interrupts, delivering traps like +/*H:220 + * Now we've got the routines to deliver interrupts, delivering traps like * page fault is easy. The only trick is that Intel decided that some traps - * should have error codes: */ + * should have error codes: + */ static bool has_err(unsigned int trap) { return (trap == 8 || (trap >= 10 && trap <= 14) || trap == 17); @@ -285,13 +329,17 @@ static bool has_err(unsigned int trap) /* deliver_trap() returns true if it could deliver the trap. */ bool deliver_trap(struct lg_cpu *cpu, unsigned int num) { - /* Trap numbers are always 8 bit, but we set an impossible trap number - * for traps inside the Switcher, so check that here. */ + /* + * Trap numbers are always 8 bit, but we set an impossible trap number + * for traps inside the Switcher, so check that here. + */ if (num >= ARRAY_SIZE(cpu->arch.idt)) return false; - /* Early on the Guest hasn't set the IDT entries (or maybe it put a - * bogus one in): if we fail here, the Guest will be killed. */ + /* + * Early on the Guest hasn't set the IDT entries (or maybe it put a + * bogus one in): if we fail here, the Guest will be killed. + */ if (!idt_present(cpu->arch.idt[num].a, cpu->arch.idt[num].b)) return false; set_guest_interrupt(cpu, cpu->arch.idt[num].a, @@ -299,7 +347,8 @@ bool deliver_trap(struct lg_cpu *cpu, unsigned int num) return true; } -/*H:250 Here's the hard part: returning to the Host every time a trap happens +/*H:250 + * Here's the hard part: returning to the Host every time a trap happens * and then calling deliver_trap() and re-entering the Guest is slow. * Particularly because Guest userspace system calls are traps (usually trap * 128). @@ -311,69 +360,87 @@ bool deliver_trap(struct lg_cpu *cpu, unsigned int num) * the other hypervisors would beat it up at lunchtime. * * This routine indicates if a particular trap number could be delivered - * directly. */ + * directly. + */ static bool direct_trap(unsigned int num) { - /* Hardware interrupts don't go to the Guest at all (except system - * call). */ + /* + * Hardware interrupts don't go to the Guest at all (except system + * call). + */ if (num >= FIRST_EXTERNAL_VECTOR && !could_be_syscall(num)) return false; - /* The Host needs to see page faults (for shadow paging and to save the + /* + * The Host needs to see page faults (for shadow paging and to save the * fault address), general protection faults (in/out emulation) and * device not available (TS handling), invalid opcode fault (kvm hcall), - * and of course, the hypercall trap. */ + * and of course, the hypercall trap. + */ return num != 14 && num != 13 && num != 7 && num != 6 && num != LGUEST_TRAP_ENTRY; } /*:*/ -/*M:005 The Guest has the ability to turn its interrupt gates into trap gates, +/*M:005 + * The Guest has the ability to turn its interrupt gates into trap gates, * if it is careful. The Host will let trap gates can go directly to the * Guest, but the Guest needs the interrupts atomically disabled for an * interrupt gate. It can do this by pointing the trap gate at instructions - * within noirq_start and noirq_end, where it can safely disable interrupts. */ + * within noirq_start and noirq_end, where it can safely disable interrupts. + */ -/*M:006 The Guests do not use the sysenter (fast system call) instruction, +/*M:006 + * The Guests do not use the sysenter (fast system call) instruction, * because it's hardcoded to enter privilege level 0 and so can't go direct. * It's about twice as fast as the older "int 0x80" system call, so it might * still be worthwhile to handle it in the Switcher and lcall down to the * Guest. The sysenter semantics are hairy tho: search for that keyword in - * entry.S :*/ + * entry.S +:*/ -/*H:260 When we make traps go directly into the Guest, we need to make sure +/*H:260 + * When we make traps go directly into the Guest, we need to make sure * the kernel stack is valid (ie. mapped in the page tables). Otherwise, the * CPU trying to deliver the trap will fault while trying to push the interrupt * words on the stack: this is called a double fault, and it forces us to kill * the Guest. * - * Which is deeply unfair, because (literally!) it wasn't the Guests' fault. */ + * Which is deeply unfair, because (literally!) it wasn't the Guests' fault. + */ void pin_stack_pages(struct lg_cpu *cpu) { unsigned int i; - /* Depending on the CONFIG_4KSTACKS option, the Guest can have one or - * two pages of stack space. */ + /* + * Depending on the CONFIG_4KSTACKS option, the Guest can have one or + * two pages of stack space. + */ for (i = 0; i < cpu->lg->stack_pages; i++) - /* The stack grows *upwards*, so the address we're given is the + /* + * The stack grows *upwards*, so the address we're given is the * start of the page after the kernel stack. Subtract one to * get back onto the first stack page, and keep subtracting to - * get to the rest of the stack pages. */ + * get to the rest of the stack pages. + */ pin_page(cpu, cpu->esp1 - 1 - i * PAGE_SIZE); } -/* Direct traps also mean that we need to know whenever the Guest wants to use +/* + * Direct traps also mean that we need to know whenever the Guest wants to use * a different kernel stack, so we can change the IDT entries to use that * stack. The IDT entries expect a virtual address, so unlike most addresses * the Guest gives us, the "esp" (stack pointer) value here is virtual, not * physical. * * In Linux each process has its own kernel stack, so this happens a lot: we - * change stacks on each context switch. */ + * change stacks on each context switch. + */ void guest_set_stack(struct lg_cpu *cpu, u32 seg, u32 esp, unsigned int pages) { - /* You are not allowed have a stack segment with privilege level 0: bad - * Guest! */ + /* + * You're not allowed a stack segment with privilege level 0: bad Guest! + */ if ((seg & 0x3) != GUEST_PL) kill_guest(cpu, "bad stack segment %i", seg); /* We only expect one or two stack pages. */ @@ -387,11 +454,15 @@ void guest_set_stack(struct lg_cpu *cpu, u32 seg, u32 esp, unsigned int pages) pin_stack_pages(cpu); } -/* All this reference to mapping stacks leads us neatly into the other complex - * part of the Host: page table handling. */ +/* + * All this reference to mapping stacks leads us neatly into the other complex + * part of the Host: page table handling. + */ -/*H:235 This is the routine which actually checks the Guest's IDT entry and - * transfers it into the entry in "struct lguest": */ +/*H:235 + * This is the routine which actually checks the Guest's IDT entry and + * transfers it into the entry in "struct lguest": + */ static void set_trap(struct lg_cpu *cpu, struct desc_struct *trap, unsigned int num, u32 lo, u32 hi) { @@ -407,30 +478,38 @@ static void set_trap(struct lg_cpu *cpu, struct desc_struct *trap, if (type != 0xE && type != 0xF) kill_guest(cpu, "bad IDT type %i", type); - /* We only copy the handler address, present bit, privilege level and + /* + * We only copy the handler address, present bit, privilege level and * type. The privilege level controls where the trap can be triggered * manually with an "int" instruction. This is usually GUEST_PL, - * except for system calls which userspace can use. */ + * except for system calls which userspace can use. + */ trap->a = ((__KERNEL_CS|GUEST_PL)<<16) | (lo&0x0000FFFF); trap->b = (hi&0xFFFFEF00); } -/*H:230 While we're here, dealing with delivering traps and interrupts to the +/*H:230 + * While we're here, dealing with delivering traps and interrupts to the * Guest, we might as well complete the picture: how the Guest tells us where * it wants them to go. This would be simple, except making traps fast * requires some tricks. * * We saw the Guest setting Interrupt Descriptor Table (IDT) entries with the - * LHCALL_LOAD_IDT_ENTRY hypercall before: that comes here. */ + * LHCALL_LOAD_IDT_ENTRY hypercall before: that comes here. + */ void load_guest_idt_entry(struct lg_cpu *cpu, unsigned int num, u32 lo, u32 hi) { - /* Guest never handles: NMI, doublefault, spurious interrupt or - * hypercall. We ignore when it tries to set them. */ + /* + * Guest never handles: NMI, doublefault, spurious interrupt or + * hypercall. We ignore when it tries to set them. + */ if (num == 2 || num == 8 || num == 15 || num == LGUEST_TRAP_ENTRY) return; - /* Mark the IDT as changed: next time the Guest runs we'll know we have - * to copy this again. */ + /* + * Mark the IDT as changed: next time the Guest runs we'll know we have + * to copy this again. + */ cpu->changed |= CHANGED_IDT; /* Check that the Guest doesn't try to step outside the bounds. */ @@ -440,9 +519,11 @@ void load_guest_idt_entry(struct lg_cpu *cpu, unsigned int num, u32 lo, u32 hi) set_trap(cpu, &cpu->arch.idt[num], num, lo, hi); } -/* The default entry for each interrupt points into the Switcher routines which +/* + * The default entry for each interrupt points into the Switcher routines which * simply return to the Host. The run_guest() loop will then call - * deliver_trap() to bounce it back into the Guest. */ + * deliver_trap() to bounce it back into the Guest. + */ static void default_idt_entry(struct desc_struct *idt, int trap, const unsigned long handler, @@ -451,13 +532,17 @@ static void default_idt_entry(struct desc_struct *idt, /* A present interrupt gate. */ u32 flags = 0x8e00; - /* Set the privilege level on the entry for the hypercall: this allows - * the Guest to use the "int" instruction to trigger it. */ + /* + * Set the privilege level on the entry for the hypercall: this allows + * the Guest to use the "int" instruction to trigger it. + */ if (trap == LGUEST_TRAP_ENTRY) flags |= (GUEST_PL << 13); else if (base) - /* Copy priv. level from what Guest asked for. This allows - * debug (int 3) traps from Guest userspace, for example. */ + /* + * Copy privilege level from what Guest asked for. This allows + * debug (int 3) traps from Guest userspace, for example. + */ flags |= (base->b & 0x6000); /* Now pack it into the IDT entry in its weird format. */ @@ -475,16 +560,20 @@ void setup_default_idt_entries(struct lguest_ro_state *state, default_idt_entry(&state->guest_idt[i], i, def[i], NULL); } -/*H:240 We don't use the IDT entries in the "struct lguest" directly, instead +/*H:240 + * We don't use the IDT entries in the "struct lguest" directly, instead * we copy them into the IDT which we've set up for Guests on this CPU, just - * before we run the Guest. This routine does that copy. */ + * before we run the Guest. This routine does that copy. + */ void copy_traps(const struct lg_cpu *cpu, struct desc_struct *idt, const unsigned long *def) { unsigned int i; - /* We can simply copy the direct traps, otherwise we use the default - * ones in the Switcher: they will return to the Host. */ + /* + * We can simply copy the direct traps, otherwise we use the default + * ones in the Switcher: they will return to the Host. + */ for (i = 0; i < ARRAY_SIZE(cpu->arch.idt); i++) { const struct desc_struct *gidt = &cpu->arch.idt[i]; @@ -492,14 +581,16 @@ void copy_traps(const struct lg_cpu *cpu, struct desc_struct *idt, if (!direct_trap(i)) continue; - /* Only trap gates (type 15) can go direct to the Guest. + /* + * Only trap gates (type 15) can go direct to the Guest. * Interrupt gates (type 14) disable interrupts as they are * entered, which we never let the Guest do. Not present * entries (type 0x0) also can't go direct, of course. * * If it can't go direct, we still need to copy the priv. level: * they might want to give userspace access to a software - * interrupt. */ + * interrupt. + */ if (idt_type(gidt->a, gidt->b) == 0xF) idt[i] = *gidt; else @@ -518,7 +609,8 @@ void copy_traps(const struct lg_cpu *cpu, struct desc_struct *idt, * the next timer interrupt (in nanoseconds). We use the high-resolution timer * infrastructure to set a callback at that time. * - * 0 means "turn off the clock". */ + * 0 means "turn off the clock". + */ void guest_set_clockevent(struct lg_cpu *cpu, unsigned long delta) { ktime_t expires; @@ -529,9 +621,11 @@ void guest_set_clockevent(struct lg_cpu *cpu, unsigned long delta) return; } - /* We use wallclock time here, so the Guest might not be running for + /* + * We use wallclock time here, so the Guest might not be running for * all the time between now and the timer interrupt it asked for. This - * is almost always the right thing to do. */ + * is almost always the right thing to do. + */ expires = ktime_add_ns(ktime_get_real(), delta); hrtimer_start(&cpu->hrt, expires, HRTIMER_MODE_ABS); } diff --git a/drivers/lguest/lg.h b/drivers/lguest/lg.h index 01c59192379..74c0db691b5 100644 --- a/drivers/lguest/lg.h +++ b/drivers/lguest/lg.h @@ -54,13 +54,13 @@ struct lg_cpu { unsigned long pending_notify; /* pfn from LHCALL_NOTIFY */ - /* At end of a page shared mapped over lguest_pages in guest. */ + /* At end of a page shared mapped over lguest_pages in guest. */ unsigned long regs_page; struct lguest_regs *regs; struct lguest_pages *last_pages; - int cpu_pgd; /* which pgd this cpu is currently using */ + int cpu_pgd; /* Which pgd this cpu is currently using */ /* If a hypercall was asked for, this points to the arguments. */ struct hcall_args *hcall; @@ -96,8 +96,11 @@ struct lguest unsigned int nr_cpus; u32 pfn_limit; - /* This provides the offset to the base of guest-physical - * memory in the Launcher. */ + + /* + * This provides the offset to the base of guest-physical memory in the + * Launcher. + */ void __user *mem_base; unsigned long kernel_address; @@ -122,11 +125,13 @@ bool lguest_address_ok(const struct lguest *lg, void __lgread(struct lg_cpu *, void *, unsigned long, unsigned); void __lgwrite(struct lg_cpu *, unsigned long, const void *, unsigned); -/*H:035 Using memory-copy operations like that is usually inconvient, so we +/*H:035 + * Using memory-copy operations like that is usually inconvient, so we * have the following helper macros which read and write a specific type (often * an unsigned long). * - * This reads into a variable of the given type then returns that. */ + * This reads into a variable of the given type then returns that. + */ #define lgread(cpu, addr, type) \ ({ type _v; __lgread((cpu), &_v, (addr), sizeof(_v)); _v; }) @@ -140,9 +145,11 @@ void __lgwrite(struct lg_cpu *, unsigned long, const void *, unsigned); int run_guest(struct lg_cpu *cpu, unsigned long __user *user); -/* Helper macros to obtain the first 12 or the last 20 bits, this is only the +/* + * Helper macros to obtain the first 12 or the last 20 bits, this is only the * first step in the migration to the kernel types. pte_pfn is already defined - * in the kernel. */ + * in the kernel. + */ #define pgd_flags(x) (pgd_val(x) & ~PAGE_MASK) #define pgd_pfn(x) (pgd_val(x) >> PAGE_SHIFT) #define pmd_flags(x) (pmd_val(x) & ~PAGE_MASK) diff --git a/drivers/lguest/lguest_device.c b/drivers/lguest/lguest_device.c index e082cdac88b..cc000e79c3d 100644 --- a/drivers/lguest/lguest_device.c +++ b/drivers/lguest/lguest_device.c @@ -1,10 +1,12 @@ -/*P:050 Lguest guests use a very simple method to describe devices. It's a +/*P:050 + * Lguest guests use a very simple method to describe devices. It's a * series of device descriptors contained just above the top of normal Guest * memory. * * We use the standard "virtio" device infrastructure, which provides us with a * console, a network and a block driver. Each one expects some configuration - * information and a "virtqueue" or two to send and receive data. :*/ + * information and a "virtqueue" or two to send and receive data. +:*/ #include #include #include @@ -20,8 +22,10 @@ /* The pointer to our (page) of device descriptions. */ static void *lguest_devices; -/* For Guests, device memory can be used as normal memory, so we cast away the - * __iomem to quieten sparse. */ +/* + * For Guests, device memory can be used as normal memory, so we cast away the + * __iomem to quieten sparse. + */ static inline void *lguest_map(unsigned long phys_addr, unsigned long pages) { return (__force void *)ioremap_cache(phys_addr, PAGE_SIZE*pages); @@ -32,8 +36,10 @@ static inline void lguest_unmap(void *addr) iounmap((__force void __iomem *)addr); } -/*D:100 Each lguest device is just a virtio device plus a pointer to its entry - * in the lguest_devices page. */ +/*D:100 + * Each lguest device is just a virtio device plus a pointer to its entry + * in the lguest_devices page. + */ struct lguest_device { struct virtio_device vdev; @@ -41,9 +47,11 @@ struct lguest_device { struct lguest_device_desc *desc; }; -/* Since the virtio infrastructure hands us a pointer to the virtio_device all +/* + * Since the virtio infrastructure hands us a pointer to the virtio_device all * the time, it helps to have a curt macro to get a pointer to the struct - * lguest_device it's enclosed in. */ + * lguest_device it's enclosed in. + */ #define to_lgdev(vd) container_of(vd, struct lguest_device, vdev) /*D:130 @@ -55,7 +63,8 @@ struct lguest_device { * the driver will look at them during setup. * * A convenient routine to return the device's virtqueue config array: - * immediately after the descriptor. */ + * immediately after the descriptor. + */ static struct lguest_vqconfig *lg_vq(const struct lguest_device_desc *desc) { return (void *)(desc + 1); @@ -98,10 +107,12 @@ static u32 lg_get_features(struct virtio_device *vdev) return features; } -/* The virtio core takes the features the Host offers, and copies the - * ones supported by the driver into the vdev->features array. Once - * that's all sorted out, this routine is called so we can tell the - * Host which features we understand and accept. */ +/* + * The virtio core takes the features the Host offers, and copies the ones + * supported by the driver into the vdev->features array. Once that's all + * sorted out, this routine is called so we can tell the Host which features we + * understand and accept. + */ static void lg_finalize_features(struct virtio_device *vdev) { unsigned int i, bits; @@ -112,10 +123,11 @@ static void lg_finalize_features(struct virtio_device *vdev) /* Give virtio_ring a chance to accept features. */ vring_transport_features(vdev); - /* The vdev->feature array is a Linux bitmask: this isn't the - * same as a the simple array of bits used by lguest devices - * for features. So we do this slow, manual conversion which is - * completely general. */ + /* + * The vdev->feature array is a Linux bitmask: this isn't the same as a + * the simple array of bits used by lguest devices for features. So we + * do this slow, manual conversion which is completely general. + */ memset(out_features, 0, desc->feature_len); bits = min_t(unsigned, desc->feature_len, sizeof(vdev->features)) * 8; for (i = 0; i < bits; i++) { @@ -146,15 +158,19 @@ static void lg_set(struct virtio_device *vdev, unsigned int offset, memcpy(lg_config(desc) + offset, buf, len); } -/* The operations to get and set the status word just access the status field - * of the device descriptor. */ +/* + * The operations to get and set the status word just access the status field + * of the device descriptor. + */ static u8 lg_get_status(struct virtio_device *vdev) { return to_lgdev(vdev)->desc->status; } -/* To notify on status updates, we (ab)use the NOTIFY hypercall, with the - * descriptor address of the device. A zero status means "reset". */ +/* + * To notify on status updates, we (ab)use the NOTIFY hypercall, with the + * descriptor address of the device. A zero status means "reset". + */ static void set_status(struct virtio_device *vdev, u8 status) { unsigned long offset = (void *)to_lgdev(vdev)->desc - lguest_devices; @@ -200,13 +216,17 @@ struct lguest_vq_info void *pages; }; -/* When the virtio_ring code wants to prod the Host, it calls us here and we +/* + * When the virtio_ring code wants to prod the Host, it calls us here and we * make a hypercall. We hand the physical address of the virtqueue so the Host - * knows which virtqueue we're talking about. */ + * knows which virtqueue we're talking about. + */ static void lg_notify(struct virtqueue *vq) { - /* We store our virtqueue information in the "priv" pointer of the - * virtqueue structure. */ + /* + * We store our virtqueue information in the "priv" pointer of the + * virtqueue structure. + */ struct lguest_vq_info *lvq = vq->priv; kvm_hypercall1(LHCALL_NOTIFY, lvq->config.pfn << PAGE_SHIFT); @@ -215,7 +235,8 @@ static void lg_notify(struct virtqueue *vq) /* An extern declaration inside a C file is bad form. Don't do it. */ extern void lguest_setup_irq(unsigned int irq); -/* This routine finds the first virtqueue described in the configuration of +/* + * This routine finds the first virtqueue described in the configuration of * this device and sets it up. * * This is kind of an ugly duckling. It'd be nicer to have a standard @@ -225,7 +246,8 @@ extern void lguest_setup_irq(unsigned int irq); * simpler for the Host to simply tell us where the pages are. * * So we provide drivers with a "find the Nth virtqueue and set it up" - * function. */ + * function. + */ static struct virtqueue *lg_find_vq(struct virtio_device *vdev, unsigned index, void (*callback)(struct virtqueue *vq), @@ -244,9 +266,11 @@ static struct virtqueue *lg_find_vq(struct virtio_device *vdev, if (!lvq) return ERR_PTR(-ENOMEM); - /* Make a copy of the "struct lguest_vqconfig" entry, which sits after + /* + * Make a copy of the "struct lguest_vqconfig" entry, which sits after * the descriptor. We need a copy because the config space might not - * be aligned correctly. */ + * be aligned correctly. + */ memcpy(&lvq->config, lg_vq(ldev->desc)+index, sizeof(lvq->config)); printk("Mapping virtqueue %i addr %lx\n", index, @@ -261,8 +285,10 @@ static struct virtqueue *lg_find_vq(struct virtio_device *vdev, goto free_lvq; } - /* OK, tell virtio_ring.c to set up a virtqueue now we know its size - * and we've got a pointer to its pages. */ + /* + * OK, tell virtio_ring.c to set up a virtqueue now we know its size + * and we've got a pointer to its pages. + */ vq = vring_new_virtqueue(lvq->config.num, LGUEST_VRING_ALIGN, vdev, lvq->pages, lg_notify, callback, name); if (!vq) { @@ -273,18 +299,23 @@ static struct virtqueue *lg_find_vq(struct virtio_device *vdev, /* Make sure the interrupt is allocated. */ lguest_setup_irq(lvq->config.irq); - /* Tell the interrupt for this virtqueue to go to the virtio_ring - * interrupt handler. */ - /* FIXME: We used to have a flag for the Host to tell us we could use + /* + * Tell the interrupt for this virtqueue to go to the virtio_ring + * interrupt handler. + * + * FIXME: We used to have a flag for the Host to tell us we could use * the interrupt as a source of randomness: it'd be nice to have that - * back.. */ + * back. + */ err = request_irq(lvq->config.irq, vring_interrupt, IRQF_SHARED, dev_name(&vdev->dev), vq); if (err) goto destroy_vring; - /* Last of all we hook up our 'struct lguest_vq_info" to the - * virtqueue's priv pointer. */ + /* + * Last of all we hook up our 'struct lguest_vq_info" to the + * virtqueue's priv pointer. + */ vq->priv = lvq; return vq; @@ -358,11 +389,14 @@ static struct virtio_config_ops lguest_config_ops = { .del_vqs = lg_del_vqs, }; -/* The root device for the lguest virtio devices. This makes them appear as - * /sys/devices/lguest/0,1,2 not /sys/devices/0,1,2. */ +/* + * The root device for the lguest virtio devices. This makes them appear as + * /sys/devices/lguest/0,1,2 not /sys/devices/0,1,2. + */ static struct device *lguest_root; -/*D:120 This is the core of the lguest bus: actually adding a new device. +/*D:120 + * This is the core of the lguest bus: actually adding a new device. * It's a separate function because it's neater that way, and because an * earlier version of the code supported hotplug and unplug. They were removed * early on because they were never used. @@ -371,14 +405,14 @@ static struct device *lguest_root; * * It's worth reading this carefully: we start with a pointer to the new device * descriptor in the "lguest_devices" page, and the offset into the device - * descriptor page so we can uniquely identify it if things go badly wrong. */ + * descriptor page so we can uniquely identify it if things go badly wrong. + */ static void add_lguest_device(struct lguest_device_desc *d, unsigned int offset) { struct lguest_device *ldev; - /* Start with zeroed memory; Linux's device layer seems to count on - * it. */ + /* Start with zeroed memory; Linux's device layer counts on it. */ ldev = kzalloc(sizeof(*ldev), GFP_KERNEL); if (!ldev) { printk(KERN_EMERG "Cannot allocate lguest dev %u type %u\n", @@ -390,15 +424,19 @@ static void add_lguest_device(struct lguest_device_desc *d, ldev->vdev.dev.parent = lguest_root; /* We have a unique device index thanks to the dev_index counter. */ ldev->vdev.id.device = d->type; - /* We have a simple set of routines for querying the device's - * configuration information and setting its status. */ + /* + * We have a simple set of routines for querying the device's + * configuration information and setting its status. + */ ldev->vdev.config = &lguest_config_ops; /* And we remember the device's descriptor for lguest_config_ops. */ ldev->desc = d; - /* register_virtio_device() sets up the generic fields for the struct + /* + * register_virtio_device() sets up the generic fields for the struct * virtio_device and calls device_register(). This makes the bus - * infrastructure look for a matching driver. */ + * infrastructure look for a matching driver. + */ if (register_virtio_device(&ldev->vdev) != 0) { printk(KERN_ERR "Failed to register lguest dev %u type %u\n", offset, d->type); @@ -406,8 +444,10 @@ static void add_lguest_device(struct lguest_device_desc *d, } } -/*D:110 scan_devices() simply iterates through the device page. The type 0 is - * reserved to mean "end of devices". */ +/*D:110 + * scan_devices() simply iterates through the device page. The type 0 is + * reserved to mean "end of devices". + */ static void scan_devices(void) { unsigned int i; @@ -426,7 +466,8 @@ static void scan_devices(void) } } -/*D:105 Fairly early in boot, lguest_devices_init() is called to set up the +/*D:105 + * Fairly early in boot, lguest_devices_init() is called to set up the * lguest device infrastructure. We check that we are a Guest by checking * pv_info.name: there are other ways of checking, but this seems most * obvious to me. @@ -437,7 +478,8 @@ static void scan_devices(void) * correct sysfs incantation). * * Finally we call scan_devices() which adds all the devices found in the - * lguest_devices page. */ + * lguest_devices page. + */ static int __init lguest_devices_init(void) { if (strcmp(pv_info.name, "lguest") != 0) @@ -456,11 +498,13 @@ static int __init lguest_devices_init(void) /* We do this after core stuff, but before the drivers. */ postcore_initcall(lguest_devices_init); -/*D:150 At this point in the journey we used to now wade through the lguest +/*D:150 + * At this point in the journey we used to now wade through the lguest * devices themselves: net, block and console. Since they're all now virtio * devices rather than lguest-specific, I've decided to ignore them. Mostly, * they're kind of boring. But this does mean you'll never experience the * thrill of reading the forbidden love scene buried deep in the block driver. * * "make Launcher" beckons, where we answer questions like "Where do Guests - * come from?", and "What do you do when someone asks for optimization?". */ + * come from?", and "What do you do when someone asks for optimization?". + */ diff --git a/drivers/lguest/lguest_user.c b/drivers/lguest/lguest_user.c index 407722a8e0c..7e92017103d 100644 --- a/drivers/lguest/lguest_user.c +++ b/drivers/lguest/lguest_user.c @@ -1,8 +1,10 @@ -/*P:200 This contains all the /dev/lguest code, whereby the userspace launcher +/*P:200 + * This contains all the /dev/lguest code, whereby the userspace launcher * controls and communicates with the Guest. For example, the first write will * tell us the Guest's memory layout, pagetable, entry point and kernel address * offset. A read will run the Guest until something happens, such as a signal - * or the Guest doing a NOTIFY out to the Launcher. :*/ + * or the Guest doing a NOTIFY out to the Launcher. +:*/ #include #include #include @@ -37,8 +39,10 @@ static int add_eventfd(struct lguest *lg, unsigned long addr, int fd) if (!addr) return -EINVAL; - /* Replace the old array with the new one, carefully: others can - * be accessing it at the same time */ + /* + * Replace the old array with the new one, carefully: others can + * be accessing it at the same time. + */ new = kmalloc(sizeof(*new) + sizeof(new->map[0]) * (old->num + 1), GFP_KERNEL); if (!new) @@ -61,8 +65,10 @@ static int add_eventfd(struct lguest *lg, unsigned long addr, int fd) /* Now put new one in place. */ rcu_assign_pointer(lg->eventfds, new); - /* We're not in a big hurry. Wait until noone's looking at old - * version, then delete it. */ + /* + * We're not in a big hurry. Wait until noone's looking at old + * version, then delete it. + */ synchronize_rcu(); kfree(old); @@ -87,8 +93,10 @@ static int attach_eventfd(struct lguest *lg, const unsigned long __user *input) return err; } -/*L:050 Sending an interrupt is done by writing LHREQ_IRQ and an interrupt - * number to /dev/lguest. */ +/*L:050 + * Sending an interrupt is done by writing LHREQ_IRQ and an interrupt + * number to /dev/lguest. + */ static int user_send_irq(struct lg_cpu *cpu, const unsigned long __user *input) { unsigned long irq; @@ -102,8 +110,10 @@ static int user_send_irq(struct lg_cpu *cpu, const unsigned long __user *input) return 0; } -/*L:040 Once our Guest is initialized, the Launcher makes it run by reading - * from /dev/lguest. */ +/*L:040 + * Once our Guest is initialized, the Launcher makes it run by reading + * from /dev/lguest. + */ static ssize_t read(struct file *file, char __user *user, size_t size,loff_t*o) { struct lguest *lg = file->private_data; @@ -139,8 +149,10 @@ static ssize_t read(struct file *file, char __user *user, size_t size,loff_t*o) return len; } - /* If we returned from read() last time because the Guest sent I/O, - * clear the flag. */ + /* + * If we returned from read() last time because the Guest sent I/O, + * clear the flag. + */ if (cpu->pending_notify) cpu->pending_notify = 0; @@ -148,8 +160,10 @@ static ssize_t read(struct file *file, char __user *user, size_t size,loff_t*o) return run_guest(cpu, (unsigned long __user *)user); } -/*L:025 This actually initializes a CPU. For the moment, a Guest is only - * uniprocessor, so "id" is always 0. */ +/*L:025 + * This actually initializes a CPU. For the moment, a Guest is only + * uniprocessor, so "id" is always 0. + */ static int lg_cpu_start(struct lg_cpu *cpu, unsigned id, unsigned long start_ip) { /* We have a limited number the number of CPUs in the lguest struct. */ @@ -164,8 +178,10 @@ static int lg_cpu_start(struct lg_cpu *cpu, unsigned id, unsigned long start_ip) /* Each CPU has a timer it can set. */ init_clockdev(cpu); - /* We need a complete page for the Guest registers: they are accessible - * to the Guest and we can only grant it access to whole pages. */ + /* + * We need a complete page for the Guest registers: they are accessible + * to the Guest and we can only grant it access to whole pages. + */ cpu->regs_page = get_zeroed_page(GFP_KERNEL); if (!cpu->regs_page) return -ENOMEM; @@ -173,29 +189,38 @@ static int lg_cpu_start(struct lg_cpu *cpu, unsigned id, unsigned long start_ip) /* We actually put the registers at the bottom of the page. */ cpu->regs = (void *)cpu->regs_page + PAGE_SIZE - sizeof(*cpu->regs); - /* Now we initialize the Guest's registers, handing it the start - * address. */ + /* + * Now we initialize the Guest's registers, handing it the start + * address. + */ lguest_arch_setup_regs(cpu, start_ip); - /* We keep a pointer to the Launcher task (ie. current task) for when - * other Guests want to wake this one (eg. console input). */ + /* + * We keep a pointer to the Launcher task (ie. current task) for when + * other Guests want to wake this one (eg. console input). + */ cpu->tsk = current; - /* We need to keep a pointer to the Launcher's memory map, because if + /* + * We need to keep a pointer to the Launcher's memory map, because if * the Launcher dies we need to clean it up. If we don't keep a - * reference, it is destroyed before close() is called. */ + * reference, it is destroyed before close() is called. + */ cpu->mm = get_task_mm(cpu->tsk); - /* We remember which CPU's pages this Guest used last, for optimization - * when the same Guest runs on the same CPU twice. */ + /* + * We remember which CPU's pages this Guest used last, for optimization + * when the same Guest runs on the same CPU twice. + */ cpu->last_pages = NULL; /* No error == success. */ return 0; } -/*L:020 The initialization write supplies 3 pointer sized (32 or 64 bit) - * values (in addition to the LHREQ_INITIALIZE value). These are: +/*L:020 + * The initialization write supplies 3 pointer sized (32 or 64 bit) values (in + * addition to the LHREQ_INITIALIZE value). These are: * * base: The start of the Guest-physical memory inside the Launcher memory. * @@ -207,14 +232,15 @@ static int lg_cpu_start(struct lg_cpu *cpu, unsigned id, unsigned long start_ip) */ static int initialize(struct file *file, const unsigned long __user *input) { - /* "struct lguest" contains everything we (the Host) know about a - * Guest. */ + /* "struct lguest" contains all we (the Host) know about a Guest. */ struct lguest *lg; int err; unsigned long args[3]; - /* We grab the Big Lguest lock, which protects against multiple - * simultaneous initializations. */ + /* + * We grab the Big Lguest lock, which protects against multiple + * simultaneous initializations. + */ mutex_lock(&lguest_lock); /* You can't initialize twice! Close the device and start again... */ if (file->private_data) { @@ -249,8 +275,10 @@ static int initialize(struct file *file, const unsigned long __user *input) if (err) goto free_eventfds; - /* Initialize the Guest's shadow page tables, using the toplevel - * address the Launcher gave us. This allocates memory, so can fail. */ + /* + * Initialize the Guest's shadow page tables, using the toplevel + * address the Launcher gave us. This allocates memory, so can fail. + */ err = init_guest_pagetable(lg); if (err) goto free_regs; @@ -275,7 +303,8 @@ unlock: return err; } -/*L:010 The first operation the Launcher does must be a write. All writes +/*L:010 + * The first operation the Launcher does must be a write. All writes * start with an unsigned long number: for the first write this must be * LHREQ_INITIALIZE to set up the Guest. After that the Launcher can use * writes of other values to send interrupts. @@ -283,12 +312,15 @@ unlock: * Note that we overload the "offset" in the /dev/lguest file to indicate what * CPU number we're dealing with. Currently this is always 0, since we only * support uniprocessor Guests, but you can see the beginnings of SMP support - * here. */ + * here. + */ static ssize_t write(struct file *file, const char __user *in, size_t size, loff_t *off) { - /* Once the Guest is initialized, we hold the "struct lguest" in the - * file private data. */ + /* + * Once the Guest is initialized, we hold the "struct lguest" in the + * file private data. + */ struct lguest *lg = file->private_data; const unsigned long __user *input = (const unsigned long __user *)in; unsigned long req; @@ -323,13 +355,15 @@ static ssize_t write(struct file *file, const char __user *in, } } -/*L:060 The final piece of interface code is the close() routine. It reverses +/*L:060 + * The final piece of interface code is the close() routine. It reverses * everything done in initialize(). This is usually called because the * Launcher exited. * * Note that the close routine returns 0 or a negative error number: it can't * really fail, but it can whine. I blame Sun for this wart, and K&R C for - * letting them do it. :*/ + * letting them do it. +:*/ static int close(struct inode *inode, struct file *file) { struct lguest *lg = file->private_data; @@ -339,8 +373,10 @@ static int close(struct inode *inode, struct file *file) if (!lg) return 0; - /* We need the big lock, to protect from inter-guest I/O and other - * Launchers initializing guests. */ + /* + * We need the big lock, to protect from inter-guest I/O and other + * Launchers initializing guests. + */ mutex_lock(&lguest_lock); /* Free up the shadow page tables for the Guest. */ @@ -351,8 +387,10 @@ static int close(struct inode *inode, struct file *file) hrtimer_cancel(&lg->cpus[i].hrt); /* We can free up the register page we allocated. */ free_page(lg->cpus[i].regs_page); - /* Now all the memory cleanups are done, it's safe to release - * the Launcher's memory management structure. */ + /* + * Now all the memory cleanups are done, it's safe to release + * the Launcher's memory management structure. + */ mmput(lg->cpus[i].mm); } @@ -361,8 +399,10 @@ static int close(struct inode *inode, struct file *file) eventfd_ctx_put(lg->eventfds->map[i].event); kfree(lg->eventfds); - /* If lg->dead doesn't contain an error code it will be NULL or a - * kmalloc()ed string, either of which is ok to hand to kfree(). */ + /* + * If lg->dead doesn't contain an error code it will be NULL or a + * kmalloc()ed string, either of which is ok to hand to kfree(). + */ if (!IS_ERR(lg->dead)) kfree(lg->dead); /* Free the memory allocated to the lguest_struct */ @@ -386,7 +426,8 @@ static int close(struct inode *inode, struct file *file) * * We begin our understanding with the Host kernel interface which the Launcher * uses: reading and writing a character device called /dev/lguest. All the - * work happens in the read(), write() and close() routines: */ + * work happens in the read(), write() and close() routines: + */ static struct file_operations lguest_fops = { .owner = THIS_MODULE, .release = close, @@ -394,8 +435,10 @@ static struct file_operations lguest_fops = { .read = read, }; -/* This is a textbook example of a "misc" character device. Populate a "struct - * miscdevice" and register it with misc_register(). */ +/* + * This is a textbook example of a "misc" character device. Populate a "struct + * miscdevice" and register it with misc_register(). + */ static struct miscdevice lguest_dev = { .minor = MISC_DYNAMIC_MINOR, .name = "lguest", diff --git a/drivers/lguest/page_tables.c b/drivers/lguest/page_tables.c index a6fe1abda24..3da902e4b4c 100644 --- a/drivers/lguest/page_tables.c +++ b/drivers/lguest/page_tables.c @@ -1,9 +1,11 @@ -/*P:700 The pagetable code, on the other hand, still shows the scars of +/*P:700 + * The pagetable code, on the other hand, still shows the scars of * previous encounters. It's functional, and as neat as it can be in the * circumstances, but be wary, for these things are subtle and break easily. * The Guest provides a virtual to physical mapping, but we can neither trust * it nor use it: we verify and convert it here then point the CPU to the - * converted Guest pages when running the Guest. :*/ + * converted Guest pages when running the Guest. +:*/ /* Copyright (C) Rusty Russell IBM Corporation 2006. * GPL v2 and any later version */ @@ -17,10 +19,12 @@ #include #include "lg.h" -/*M:008 We hold reference to pages, which prevents them from being swapped. +/*M:008 + * We hold reference to pages, which prevents them from being swapped. * It'd be nice to have a callback in the "struct mm_struct" when Linux wants * to swap out. If we had this, and a shrinker callback to trim PTE pages, we - * could probably consider launching Guests as non-root. :*/ + * could probably consider launching Guests as non-root. +:*/ /*H:300 * The Page Table Code @@ -45,16 +49,19 @@ * (v) Flushing (throwing away) page tables, * (vi) Mapping the Switcher when the Guest is about to run, * (vii) Setting up the page tables initially. - :*/ +:*/ - -/* 1024 entries in a page table page maps 1024 pages: 4MB. The Switcher is +/* + * 1024 entries in a page table page maps 1024 pages: 4MB. The Switcher is * conveniently placed at the top 4MB, so it uses a separate, complete PTE - * page. */ + * page. + */ #define SWITCHER_PGD_INDEX (PTRS_PER_PGD - 1) -/* For PAE we need the PMD index as well. We use the last 2MB, so we - * will need the last pmd entry of the last pmd page. */ +/* + * For PAE we need the PMD index as well. We use the last 2MB, so we + * will need the last pmd entry of the last pmd page. + */ #ifdef CONFIG_X86_PAE #define SWITCHER_PMD_INDEX (PTRS_PER_PMD - 1) #define RESERVE_MEM 2U @@ -64,13 +71,16 @@ #define CHECK_GPGD_MASK _PAGE_TABLE #endif -/* We actually need a separate PTE page for each CPU. Remember that after the +/* + * We actually need a separate PTE page for each CPU. Remember that after the * Switcher code itself comes two pages for each CPU, and we don't want this - * CPU's guest to see the pages of any other CPU. */ + * CPU's guest to see the pages of any other CPU. + */ static DEFINE_PER_CPU(pte_t *, switcher_pte_pages); #define switcher_pte_page(cpu) per_cpu(switcher_pte_pages, cpu) -/*H:320 The page table code is curly enough to need helper functions to keep it +/*H:320 + * The page table code is curly enough to need helper functions to keep it * clear and clean. * * There are two functions which return pointers to the shadow (aka "real") @@ -79,7 +89,8 @@ static DEFINE_PER_CPU(pte_t *, switcher_pte_pages); * spgd_addr() takes the virtual address and returns a pointer to the top-level * page directory entry (PGD) for that address. Since we keep track of several * page tables, the "i" argument tells us which one we're interested in (it's - * usually the current one). */ + * usually the current one). + */ static pgd_t *spgd_addr(struct lg_cpu *cpu, u32 i, unsigned long vaddr) { unsigned int index = pgd_index(vaddr); @@ -96,9 +107,11 @@ static pgd_t *spgd_addr(struct lg_cpu *cpu, u32 i, unsigned long vaddr) } #ifdef CONFIG_X86_PAE -/* This routine then takes the PGD entry given above, which contains the +/* + * This routine then takes the PGD entry given above, which contains the * address of the PMD page. It then returns a pointer to the PMD entry for the - * given address. */ + * given address. + */ static pmd_t *spmd_addr(struct lg_cpu *cpu, pgd_t spgd, unsigned long vaddr) { unsigned int index = pmd_index(vaddr); @@ -119,9 +132,11 @@ static pmd_t *spmd_addr(struct lg_cpu *cpu, pgd_t spgd, unsigned long vaddr) } #endif -/* This routine then takes the page directory entry returned above, which +/* + * This routine then takes the page directory entry returned above, which * contains the address of the page table entry (PTE) page. It then returns a - * pointer to the PTE entry for the given address. */ + * pointer to the PTE entry for the given address. + */ static pte_t *spte_addr(struct lg_cpu *cpu, pgd_t spgd, unsigned long vaddr) { #ifdef CONFIG_X86_PAE @@ -139,8 +154,10 @@ static pte_t *spte_addr(struct lg_cpu *cpu, pgd_t spgd, unsigned long vaddr) return &page[pte_index(vaddr)]; } -/* These two functions just like the above two, except they access the Guest - * page tables. Hence they return a Guest address. */ +/* + * These two functions just like the above two, except they access the Guest + * page tables. Hence they return a Guest address. + */ static unsigned long gpgd_addr(struct lg_cpu *cpu, unsigned long vaddr) { unsigned int index = vaddr >> (PGDIR_SHIFT); @@ -175,17 +192,21 @@ static unsigned long gpte_addr(struct lg_cpu *cpu, #endif /*:*/ -/*M:014 get_pfn is slow: we could probably try to grab batches of pages here as - * an optimization (ie. pre-faulting). :*/ +/*M:014 + * get_pfn is slow: we could probably try to grab batches of pages here as + * an optimization (ie. pre-faulting). +:*/ -/*H:350 This routine takes a page number given by the Guest and converts it to +/*H:350 + * This routine takes a page number given by the Guest and converts it to * an actual, physical page number. It can fail for several reasons: the * virtual address might not be mapped by the Launcher, the write flag is set * and the page is read-only, or the write flag was set and the page was * shared so had to be copied, but we ran out of memory. * * This holds a reference to the page, so release_pte() is careful to put that - * back. */ + * back. + */ static unsigned long get_pfn(unsigned long virtpfn, int write) { struct page *page; @@ -198,33 +219,41 @@ static unsigned long get_pfn(unsigned long virtpfn, int write) return -1UL; } -/*H:340 Converting a Guest page table entry to a shadow (ie. real) page table +/*H:340 + * Converting a Guest page table entry to a shadow (ie. real) page table * entry can be a little tricky. The flags are (almost) the same, but the * Guest PTE contains a virtual page number: the CPU needs the real page - * number. */ + * number. + */ static pte_t gpte_to_spte(struct lg_cpu *cpu, pte_t gpte, int write) { unsigned long pfn, base, flags; - /* The Guest sets the global flag, because it thinks that it is using + /* + * The Guest sets the global flag, because it thinks that it is using * PGE. We only told it to use PGE so it would tell us whether it was * flushing a kernel mapping or a userspace mapping. We don't actually - * use the global bit, so throw it away. */ + * use the global bit, so throw it away. + */ flags = (pte_flags(gpte) & ~_PAGE_GLOBAL); /* The Guest's pages are offset inside the Launcher. */ base = (unsigned long)cpu->lg->mem_base / PAGE_SIZE; - /* We need a temporary "unsigned long" variable to hold the answer from + /* + * We need a temporary "unsigned long" variable to hold the answer from * get_pfn(), because it returns 0xFFFFFFFF on failure, which wouldn't * fit in spte.pfn. get_pfn() finds the real physical number of the - * page, given the virtual number. */ + * page, given the virtual number. + */ pfn = get_pfn(base + pte_pfn(gpte), write); if (pfn == -1UL) { kill_guest(cpu, "failed to get page %lu", pte_pfn(gpte)); - /* When we destroy the Guest, we'll go through the shadow page + /* + * When we destroy the Guest, we'll go through the shadow page * tables and release_pte() them. Make sure we don't think - * this one is valid! */ + * this one is valid! + */ flags = 0; } /* Now we assemble our shadow PTE from the page number and flags. */ @@ -234,8 +263,10 @@ static pte_t gpte_to_spte(struct lg_cpu *cpu, pte_t gpte, int write) /*H:460 And to complete the chain, release_pte() looks like this: */ static void release_pte(pte_t pte) { - /* Remember that get_user_pages_fast() took a reference to the page, in - * get_pfn()? We have to put it back now. */ + /* + * Remember that get_user_pages_fast() took a reference to the page, in + * get_pfn()? We have to put it back now. + */ if (pte_flags(pte) & _PAGE_PRESENT) put_page(pte_page(pte)); } @@ -273,7 +304,8 @@ static void check_gpmd(struct lg_cpu *cpu, pmd_t gpmd) * and return to the Guest without it knowing. * * If we fixed up the fault (ie. we mapped the address), this routine returns - * true. Otherwise, it was a real fault and we need to tell the Guest. */ + * true. Otherwise, it was a real fault and we need to tell the Guest. + */ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) { pgd_t gpgd; @@ -298,22 +330,26 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) if (!(pgd_flags(*spgd) & _PAGE_PRESENT)) { /* No shadow entry: allocate a new shadow PTE page. */ unsigned long ptepage = get_zeroed_page(GFP_KERNEL); - /* This is not really the Guest's fault, but killing it is - * simple for this corner case. */ + /* + * This is not really the Guest's fault, but killing it is + * simple for this corner case. + */ if (!ptepage) { kill_guest(cpu, "out of memory allocating pte page"); return false; } /* We check that the Guest pgd is OK. */ check_gpgd(cpu, gpgd); - /* And we copy the flags to the shadow PGD entry. The page - * number in the shadow PGD is the page we just allocated. */ + /* + * And we copy the flags to the shadow PGD entry. The page + * number in the shadow PGD is the page we just allocated. + */ set_pgd(spgd, __pgd(__pa(ptepage) | pgd_flags(gpgd))); } #ifdef CONFIG_X86_PAE gpmd = lgread(cpu, gpmd_addr(gpgd, vaddr), pmd_t); - /* middle level not present? We can't map it in. */ + /* Middle level not present? We can't map it in. */ if (!(pmd_flags(gpmd) & _PAGE_PRESENT)) return false; @@ -324,8 +360,10 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) /* No shadow entry: allocate a new shadow PTE page. */ unsigned long ptepage = get_zeroed_page(GFP_KERNEL); - /* This is not really the Guest's fault, but killing it is - * simple for this corner case. */ + /* + * This is not really the Guest's fault, but killing it is + * simple for this corner case. + */ if (!ptepage) { kill_guest(cpu, "out of memory allocating pte page"); return false; @@ -334,17 +372,23 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) /* We check that the Guest pmd is OK. */ check_gpmd(cpu, gpmd); - /* And we copy the flags to the shadow PMD entry. The page - * number in the shadow PMD is the page we just allocated. */ + /* + * And we copy the flags to the shadow PMD entry. The page + * number in the shadow PMD is the page we just allocated. + */ native_set_pmd(spmd, __pmd(__pa(ptepage) | pmd_flags(gpmd))); } - /* OK, now we look at the lower level in the Guest page table: keep its - * address, because we might update it later. */ + /* + * OK, now we look at the lower level in the Guest page table: keep its + * address, because we might update it later. + */ gpte_ptr = gpte_addr(cpu, gpmd, vaddr); #else - /* OK, now we look at the lower level in the Guest page table: keep its - * address, because we might update it later. */ + /* + * OK, now we look at the lower level in the Guest page table: keep its + * address, because we might update it later. + */ gpte_ptr = gpte_addr(cpu, gpgd, vaddr); #endif gpte = lgread(cpu, gpte_ptr, pte_t); @@ -353,8 +397,10 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) if (!(pte_flags(gpte) & _PAGE_PRESENT)) return false; - /* Check they're not trying to write to a page the Guest wants - * read-only (bit 2 of errcode == write). */ + /* + * Check they're not trying to write to a page the Guest wants + * read-only (bit 2 of errcode == write). + */ if ((errcode & 2) && !(pte_flags(gpte) & _PAGE_RW)) return false; @@ -362,8 +408,10 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) if ((errcode & 4) && !(pte_flags(gpte) & _PAGE_USER)) return false; - /* Check that the Guest PTE flags are OK, and the page number is below - * the pfn_limit (ie. not mapping the Launcher binary). */ + /* + * Check that the Guest PTE flags are OK, and the page number is below + * the pfn_limit (ie. not mapping the Launcher binary). + */ check_gpte(cpu, gpte); /* Add the _PAGE_ACCESSED and (for a write) _PAGE_DIRTY flag */ @@ -373,29 +421,40 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) /* Get the pointer to the shadow PTE entry we're going to set. */ spte = spte_addr(cpu, *spgd, vaddr); - /* If there was a valid shadow PTE entry here before, we release it. - * This can happen with a write to a previously read-only entry. */ + + /* + * If there was a valid shadow PTE entry here before, we release it. + * This can happen with a write to a previously read-only entry. + */ release_pte(*spte); - /* If this is a write, we insist that the Guest page is writable (the - * final arg to gpte_to_spte()). */ + /* + * If this is a write, we insist that the Guest page is writable (the + * final arg to gpte_to_spte()). + */ if (pte_dirty(gpte)) *spte = gpte_to_spte(cpu, gpte, 1); else - /* If this is a read, don't set the "writable" bit in the page + /* + * If this is a read, don't set the "writable" bit in the page * table entry, even if the Guest says it's writable. That way * we will come back here when a write does actually occur, so - * we can update the Guest's _PAGE_DIRTY flag. */ + * we can update the Guest's _PAGE_DIRTY flag. + */ native_set_pte(spte, gpte_to_spte(cpu, pte_wrprotect(gpte), 0)); - /* Finally, we write the Guest PTE entry back: we've set the - * _PAGE_ACCESSED and maybe the _PAGE_DIRTY flags. */ + /* + * Finally, we write the Guest PTE entry back: we've set the + * _PAGE_ACCESSED and maybe the _PAGE_DIRTY flags. + */ lgwrite(cpu, gpte_ptr, pte_t, gpte); - /* The fault is fixed, the page table is populated, the mapping + /* + * The fault is fixed, the page table is populated, the mapping * manipulated, the result returned and the code complete. A small * delay and a trace of alliteration are the only indications the Guest - * has that a page fault occurred at all. */ + * has that a page fault occurred at all. + */ return true; } @@ -408,7 +467,8 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) * mapped, so it's overkill. * * This is a quick version which answers the question: is this virtual address - * mapped by the shadow page tables, and is it writable? */ + * mapped by the shadow page tables, and is it writable? + */ static bool page_writable(struct lg_cpu *cpu, unsigned long vaddr) { pgd_t *spgd; @@ -428,16 +488,20 @@ static bool page_writable(struct lg_cpu *cpu, unsigned long vaddr) return false; #endif - /* Check the flags on the pte entry itself: it must be present and - * writable. */ + /* + * Check the flags on the pte entry itself: it must be present and + * writable. + */ flags = pte_flags(*(spte_addr(cpu, *spgd, vaddr))); return (flags & (_PAGE_PRESENT|_PAGE_RW)) == (_PAGE_PRESENT|_PAGE_RW); } -/* So, when pin_stack_pages() asks us to pin a page, we check if it's already +/* + * So, when pin_stack_pages() asks us to pin a page, we check if it's already * in the page tables, and if not, we call demand_page() with error code 2 - * (meaning "write"). */ + * (meaning "write"). + */ void pin_page(struct lg_cpu *cpu, unsigned long vaddr) { if (!page_writable(cpu, vaddr) && !demand_page(cpu, vaddr, 2)) @@ -485,9 +549,11 @@ static void release_pgd(pgd_t *spgd) /* If the entry's not present, there's nothing to release. */ if (pgd_flags(*spgd) & _PAGE_PRESENT) { unsigned int i; - /* Converting the pfn to find the actual PTE page is easy: turn + /* + * Converting the pfn to find the actual PTE page is easy: turn * the page number into a physical address, then convert to a - * virtual address (easy for kernel pages like this one). */ + * virtual address (easy for kernel pages like this one). + */ pte_t *ptepage = __va(pgd_pfn(*spgd) << PAGE_SHIFT); /* For each entry in the page, we might need to release it. */ for (i = 0; i < PTRS_PER_PTE; i++) @@ -499,9 +565,12 @@ static void release_pgd(pgd_t *spgd) } } #endif -/*H:445 We saw flush_user_mappings() twice: once from the flush_user_mappings() + +/*H:445 + * We saw flush_user_mappings() twice: once from the flush_user_mappings() * hypercall and once in new_pgdir() when we re-used a top-level pgdir page. - * It simply releases every PTE page from 0 up to the Guest's kernel address. */ + * It simply releases every PTE page from 0 up to the Guest's kernel address. + */ static void flush_user_mappings(struct lguest *lg, int idx) { unsigned int i; @@ -510,10 +579,12 @@ static void flush_user_mappings(struct lguest *lg, int idx) release_pgd(lg->pgdirs[idx].pgdir + i); } -/*H:440 (v) Flushing (throwing away) page tables, +/*H:440 + * (v) Flushing (throwing away) page tables, * * The Guest has a hypercall to throw away the page tables: it's used when a - * large number of mappings have been changed. */ + * large number of mappings have been changed. + */ void guest_pagetable_flush_user(struct lg_cpu *cpu) { /* Drop the userspace part of the current page table. */ @@ -551,9 +622,11 @@ unsigned long guest_pa(struct lg_cpu *cpu, unsigned long vaddr) return pte_pfn(gpte) * PAGE_SIZE | (vaddr & ~PAGE_MASK); } -/* We keep several page tables. This is a simple routine to find the page +/* + * We keep several page tables. This is a simple routine to find the page * table (if any) corresponding to this top-level address the Guest has given - * us. */ + * us. + */ static unsigned int find_pgdir(struct lguest *lg, unsigned long pgtable) { unsigned int i; @@ -563,9 +636,11 @@ static unsigned int find_pgdir(struct lguest *lg, unsigned long pgtable) return i; } -/*H:435 And this is us, creating the new page directory. If we really do +/*H:435 + * And this is us, creating the new page directory. If we really do * allocate a new one (and so the kernel parts are not there), we set - * blank_pgdir. */ + * blank_pgdir. + */ static unsigned int new_pgdir(struct lg_cpu *cpu, unsigned long gpgdir, int *blank_pgdir) @@ -575,8 +650,10 @@ static unsigned int new_pgdir(struct lg_cpu *cpu, pmd_t *pmd_table; #endif - /* We pick one entry at random to throw out. Choosing the Least - * Recently Used might be better, but this is easy. */ + /* + * We pick one entry at random to throw out. Choosing the Least + * Recently Used might be better, but this is easy. + */ next = random32() % ARRAY_SIZE(cpu->lg->pgdirs); /* If it's never been allocated at all before, try now. */ if (!cpu->lg->pgdirs[next].pgdir) { @@ -587,8 +664,10 @@ static unsigned int new_pgdir(struct lg_cpu *cpu, next = cpu->cpu_pgd; else { #ifdef CONFIG_X86_PAE - /* In PAE mode, allocate a pmd page and populate the - * last pgd entry. */ + /* + * In PAE mode, allocate a pmd page and populate the + * last pgd entry. + */ pmd_table = (pmd_t *)get_zeroed_page(GFP_KERNEL); if (!pmd_table) { free_page((long)cpu->lg->pgdirs[next].pgdir); @@ -598,8 +677,10 @@ static unsigned int new_pgdir(struct lg_cpu *cpu, set_pgd(cpu->lg->pgdirs[next].pgdir + SWITCHER_PGD_INDEX, __pgd(__pa(pmd_table) | _PAGE_PRESENT)); - /* This is a blank page, so there are no kernel - * mappings: caller must map the stack! */ + /* + * This is a blank page, so there are no kernel + * mappings: caller must map the stack! + */ *blank_pgdir = 1; } #else @@ -615,19 +696,23 @@ static unsigned int new_pgdir(struct lg_cpu *cpu, return next; } -/*H:430 (iv) Switching page tables +/*H:430 + * (iv) Switching page tables * * Now we've seen all the page table setting and manipulation, let's see * what happens when the Guest changes page tables (ie. changes the top-level - * pgdir). This occurs on almost every context switch. */ + * pgdir). This occurs on almost every context switch. + */ void guest_new_pagetable(struct lg_cpu *cpu, unsigned long pgtable) { int newpgdir, repin = 0; /* Look to see if we have this one already. */ newpgdir = find_pgdir(cpu->lg, pgtable); - /* If not, we allocate or mug an existing one: if it's a fresh one, - * repin gets set to 1. */ + /* + * If not, we allocate or mug an existing one: if it's a fresh one, + * repin gets set to 1. + */ if (newpgdir == ARRAY_SIZE(cpu->lg->pgdirs)) newpgdir = new_pgdir(cpu, pgtable, &repin); /* Change the current pgd index to the new one. */ @@ -637,9 +722,11 @@ void guest_new_pagetable(struct lg_cpu *cpu, unsigned long pgtable) pin_stack_pages(cpu); } -/*H:470 Finally, a routine which throws away everything: all PGD entries in all +/*H:470 + * Finally, a routine which throws away everything: all PGD entries in all * the shadow page tables, including the Guest's kernel mappings. This is used - * when we destroy the Guest. */ + * when we destroy the Guest. + */ static void release_all_pagetables(struct lguest *lg) { unsigned int i, j; @@ -656,8 +743,10 @@ static void release_all_pagetables(struct lguest *lg) spgd = lg->pgdirs[i].pgdir + SWITCHER_PGD_INDEX; pmdpage = __va(pgd_pfn(*spgd) << PAGE_SHIFT); - /* And release the pmd entries of that pmd page, - * except for the switcher pmd. */ + /* + * And release the pmd entries of that pmd page, + * except for the switcher pmd. + */ for (k = 0; k < SWITCHER_PMD_INDEX; k++) release_pmd(&pmdpage[k]); #endif @@ -667,10 +756,12 @@ static void release_all_pagetables(struct lguest *lg) } } -/* We also throw away everything when a Guest tells us it's changed a kernel +/* + * We also throw away everything when a Guest tells us it's changed a kernel * mapping. Since kernel mappings are in every page table, it's easiest to * throw them all away. This traps the Guest in amber for a while as - * everything faults back in, but it's rare. */ + * everything faults back in, but it's rare. + */ void guest_pagetable_clear_all(struct lg_cpu *cpu) { release_all_pagetables(cpu->lg); @@ -678,15 +769,19 @@ void guest_pagetable_clear_all(struct lg_cpu *cpu) pin_stack_pages(cpu); } /*:*/ -/*M:009 Since we throw away all mappings when a kernel mapping changes, our + +/*M:009 + * Since we throw away all mappings when a kernel mapping changes, our * performance sucks for guests using highmem. In fact, a guest with * PAGE_OFFSET 0xc0000000 (the default) and more than about 700MB of RAM is * usually slower than a Guest with less memory. * * This, of course, cannot be fixed. It would take some kind of... well, I - * don't know, but the term "puissant code-fu" comes to mind. :*/ + * don't know, but the term "puissant code-fu" comes to mind. +:*/ -/*H:420 This is the routine which actually sets the page table entry for then +/*H:420 + * This is the routine which actually sets the page table entry for then * "idx"'th shadow page table. * * Normally, we can just throw out the old entry and replace it with 0: if they @@ -715,31 +810,36 @@ static void do_set_pte(struct lg_cpu *cpu, int idx, spmd = spmd_addr(cpu, *spgd, vaddr); if (pmd_flags(*spmd) & _PAGE_PRESENT) { #endif - /* Otherwise, we start by releasing - * the existing entry. */ + /* Otherwise, start by releasing the existing entry. */ pte_t *spte = spte_addr(cpu, *spgd, vaddr); release_pte(*spte); - /* If they're setting this entry as dirty or accessed, - * we might as well put that entry they've given us - * in now. This shaves 10% off a - * copy-on-write micro-benchmark. */ + /* + * If they're setting this entry as dirty or accessed, + * we might as well put that entry they've given us in + * now. This shaves 10% off a copy-on-write + * micro-benchmark. + */ if (pte_flags(gpte) & (_PAGE_DIRTY | _PAGE_ACCESSED)) { check_gpte(cpu, gpte); native_set_pte(spte, gpte_to_spte(cpu, gpte, pte_flags(gpte) & _PAGE_DIRTY)); - } else - /* Otherwise kill it and we can demand_page() - * it in later. */ + } else { + /* + * Otherwise kill it and we can demand_page() + * it in later. + */ native_set_pte(spte, __pte(0)); + } #ifdef CONFIG_X86_PAE } #endif } } -/*H:410 Updating a PTE entry is a little trickier. +/*H:410 + * Updating a PTE entry is a little trickier. * * We keep track of several different page tables (the Guest uses one for each * process, so it makes sense to cache at least a few). Each of these have @@ -748,12 +848,15 @@ static void do_set_pte(struct lg_cpu *cpu, int idx, * all the page tables, not just the current one. This is rare. * * The benefit is that when we have to track a new page table, we can keep all - * the kernel mappings. This speeds up context switch immensely. */ + * the kernel mappings. This speeds up context switch immensely. + */ void guest_set_pte(struct lg_cpu *cpu, unsigned long gpgdir, unsigned long vaddr, pte_t gpte) { - /* Kernel mappings must be changed on all top levels. Slow, but doesn't - * happen often. */ + /* + * Kernel mappings must be changed on all top levels. Slow, but doesn't + * happen often. + */ if (vaddr >= cpu->lg->kernel_address) { unsigned int i; for (i = 0; i < ARRAY_SIZE(cpu->lg->pgdirs); i++) @@ -802,12 +905,14 @@ void guest_set_pmd(struct lguest *lg, unsigned long pmdp, u32 idx) } #endif -/* Once we know how much memory we have we can construct simple identity - * (which set virtual == physical) and linear mappings - * which will get the Guest far enough into the boot to create its own. +/* + * Once we know how much memory we have we can construct simple identity (which + * set virtual == physical) and linear mappings which will get the Guest far + * enough into the boot to create its own. * * We lay them out of the way, just below the initrd (which is why we need to - * know its size here). */ + * know its size here). + */ static unsigned long setup_pagetables(struct lguest *lg, unsigned long mem, unsigned long initrd_size) @@ -825,8 +930,10 @@ static unsigned long setup_pagetables(struct lguest *lg, unsigned int phys_linear; #endif - /* We have mapped_pages frames to map, so we need - * linear_pages page tables to map them. */ + /* + * We have mapped_pages frames to map, so we need linear_pages page + * tables to map them. + */ mapped_pages = mem / PAGE_SIZE; linear_pages = (mapped_pages + PTRS_PER_PTE - 1) / PTRS_PER_PTE; @@ -839,8 +946,10 @@ static unsigned long setup_pagetables(struct lguest *lg, #ifdef CONFIG_X86_PAE pmds = (void *)linear - PAGE_SIZE; #endif - /* Linear mapping is easy: put every page's address into the - * mapping in order. */ + /* + * Linear mapping is easy: put every page's address into the + * mapping in order. + */ for (i = 0; i < mapped_pages; i++) { pte_t pte; pte = pfn_pte(i, __pgprot(_PAGE_PRESENT|_PAGE_RW|_PAGE_USER)); @@ -848,8 +957,10 @@ static unsigned long setup_pagetables(struct lguest *lg, return -EFAULT; } - /* The top level points to the linear page table pages above. - * We setup the identity and linear mappings here. */ + /* + * The top level points to the linear page table pages above. + * We setup the identity and linear mappings here. + */ #ifdef CONFIG_X86_PAE for (i = j = 0; i < mapped_pages && j < PTRS_PER_PMD; i += PTRS_PER_PTE, j++) { @@ -880,15 +991,19 @@ static unsigned long setup_pagetables(struct lguest *lg, } #endif - /* We return the top level (guest-physical) address: remember where - * this is. */ + /* + * We return the top level (guest-physical) address: remember where + * this is. + */ return (unsigned long)pgdir - mem_base; } -/*H:500 (vii) Setting up the page tables initially. +/*H:500 + * (vii) Setting up the page tables initially. * * When a Guest is first created, the Launcher tells us where the toplevel of - * its first page table is. We set some things up here: */ + * its first page table is. We set some things up here: + */ int init_guest_pagetable(struct lguest *lg) { u64 mem; @@ -898,14 +1013,18 @@ int init_guest_pagetable(struct lguest *lg) pgd_t *pgd; pmd_t *pmd_table; #endif - /* Get the Guest memory size and the ramdisk size from the boot header - * located at lg->mem_base (Guest address 0). */ + /* + * Get the Guest memory size and the ramdisk size from the boot header + * located at lg->mem_base (Guest address 0). + */ if (copy_from_user(&mem, &boot->e820_map[0].size, sizeof(mem)) || get_user(initrd_size, &boot->hdr.ramdisk_size)) return -EFAULT; - /* We start on the first shadow page table, and give it a blank PGD - * page. */ + /* + * We start on the first shadow page table, and give it a blank PGD + * page. + */ lg->pgdirs[0].gpgdir = setup_pagetables(lg, mem, initrd_size); if (IS_ERR_VALUE(lg->pgdirs[0].gpgdir)) return lg->pgdirs[0].gpgdir; @@ -931,17 +1050,21 @@ void page_table_guest_data_init(struct lg_cpu *cpu) /* We get the kernel address: above this is all kernel memory. */ if (get_user(cpu->lg->kernel_address, &cpu->lg->lguest_data->kernel_address) - /* We tell the Guest that it can't use the top 2 or 4 MB - * of virtual addresses used by the Switcher. */ + /* + * We tell the Guest that it can't use the top 2 or 4 MB + * of virtual addresses used by the Switcher. + */ || put_user(RESERVE_MEM * 1024 * 1024, &cpu->lg->lguest_data->reserve_mem) || put_user(cpu->lg->pgdirs[0].gpgdir, &cpu->lg->lguest_data->pgdir)) kill_guest(cpu, "bad guest page %p", cpu->lg->lguest_data); - /* In flush_user_mappings() we loop from 0 to + /* + * In flush_user_mappings() we loop from 0 to * "pgd_index(lg->kernel_address)". This assumes it won't hit the - * Switcher mappings, so check that now. */ + * Switcher mappings, so check that now. + */ #ifdef CONFIG_X86_PAE if (pgd_index(cpu->lg->kernel_address) == SWITCHER_PGD_INDEX && pmd_index(cpu->lg->kernel_address) == SWITCHER_PMD_INDEX) @@ -964,12 +1087,14 @@ void free_guest_pagetable(struct lguest *lg) free_page((long)lg->pgdirs[i].pgdir); } -/*H:480 (vi) Mapping the Switcher when the Guest is about to run. +/*H:480 + * (vi) Mapping the Switcher when the Guest is about to run. * * The Switcher and the two pages for this CPU need to be visible in the * Guest (and not the pages for other CPUs). We have the appropriate PTE pages * for each CPU already set up, we just need to hook them in now we know which - * Guest is about to run on this CPU. */ + * Guest is about to run on this CPU. + */ void map_switcher_in_guest(struct lg_cpu *cpu, struct lguest_pages *pages) { pte_t *switcher_pte_page = __get_cpu_var(switcher_pte_pages); @@ -990,20 +1115,24 @@ void map_switcher_in_guest(struct lg_cpu *cpu, struct lguest_pages *pages) #else pgd_t switcher_pgd; - /* Make the last PGD entry for this Guest point to the Switcher's PTE - * page for this CPU (with appropriate flags). */ + /* + * Make the last PGD entry for this Guest point to the Switcher's PTE + * page for this CPU (with appropriate flags). + */ switcher_pgd = __pgd(__pa(switcher_pte_page) | __PAGE_KERNEL_EXEC); cpu->lg->pgdirs[cpu->cpu_pgd].pgdir[SWITCHER_PGD_INDEX] = switcher_pgd; #endif - /* We also change the Switcher PTE page. When we're running the Guest, + /* + * We also change the Switcher PTE page. When we're running the Guest, * we want the Guest's "regs" page to appear where the first Switcher * page for this CPU is. This is an optimization: when the Switcher * saves the Guest registers, it saves them into the first page of this * CPU's "struct lguest_pages": if we make sure the Guest's register * page is already mapped there, we don't have to copy them out - * again. */ + * again. + */ pfn = __pa(cpu->regs_page) >> PAGE_SHIFT; native_set_pte(®s_pte, pfn_pte(pfn, PAGE_KERNEL)); native_set_pte(&switcher_pte_page[pte_index((unsigned long)pages)], @@ -1019,10 +1148,12 @@ static void free_switcher_pte_pages(void) free_page((long)switcher_pte_page(i)); } -/*H:520 Setting up the Switcher PTE page for given CPU is fairly easy, given +/*H:520 + * Setting up the Switcher PTE page for given CPU is fairly easy, given * the CPU number and the "struct page"s for the Switcher code itself. * - * Currently the Switcher is less than a page long, so "pages" is always 1. */ + * Currently the Switcher is less than a page long, so "pages" is always 1. + */ static __init void populate_switcher_pte_page(unsigned int cpu, struct page *switcher_page[], unsigned int pages) @@ -1043,13 +1174,16 @@ static __init void populate_switcher_pte_page(unsigned int cpu, native_set_pte(&pte[i], pfn_pte(page_to_pfn(switcher_page[i]), __pgprot(_PAGE_PRESENT|_PAGE_ACCESSED|_PAGE_RW))); - /* The second page contains the "struct lguest_ro_state", and is - * read-only. */ + /* + * The second page contains the "struct lguest_ro_state", and is + * read-only. + */ native_set_pte(&pte[i+1], pfn_pte(page_to_pfn(switcher_page[i+1]), __pgprot(_PAGE_PRESENT|_PAGE_ACCESSED))); } -/* We've made it through the page table code. Perhaps our tired brains are +/* + * We've made it through the page table code. Perhaps our tired brains are * still processing the details, or perhaps we're simply glad it's over. * * If nothing else, note that all this complexity in juggling shadow page tables @@ -1058,10 +1192,13 @@ static __init void populate_switcher_pte_page(unsigned int cpu, * uses exotic direct Guest pagetable manipulation, and why both Intel and AMD * have implemented shadow page table support directly into hardware. * - * There is just one file remaining in the Host. */ + * There is just one file remaining in the Host. + */ -/*H:510 At boot or module load time, init_pagetables() allocates and populates - * the Switcher PTE page for each CPU. */ +/*H:510 + * At boot or module load time, init_pagetables() allocates and populates + * the Switcher PTE page for each CPU. + */ __init int init_pagetables(struct page **switcher_page, unsigned int pages) { unsigned int i; diff --git a/drivers/lguest/segments.c b/drivers/lguest/segments.c index 482ed5a1875..951c57b0a7e 100644 --- a/drivers/lguest/segments.c +++ b/drivers/lguest/segments.c @@ -1,4 +1,5 @@ -/*P:600 The x86 architecture has segments, which involve a table of descriptors +/*P:600 + * The x86 architecture has segments, which involve a table of descriptors * which can be used to do funky things with virtual address interpretation. * We originally used to use segments so the Guest couldn't alter the * Guest<->Host Switcher, and then we had to trim Guest segments, and restore @@ -8,7 +9,8 @@ * * In these modern times, the segment handling code consists of simple sanity * checks, and the worst you'll experience reading this code is butterfly-rash - * from frolicking through its parklike serenity. :*/ + * from frolicking through its parklike serenity. +:*/ #include "lg.h" /*H:600 @@ -41,10 +43,12 @@ * begin. */ -/* There are several entries we don't let the Guest set. The TSS entry is the +/* + * There are several entries we don't let the Guest set. The TSS entry is the * "Task State Segment" which controls all kinds of delicate things. The * LGUEST_CS and LGUEST_DS entries are reserved for the Switcher, and the - * the Guest can't be trusted to deal with double faults. */ + * the Guest can't be trusted to deal with double faults. + */ static bool ignored_gdt(unsigned int num) { return (num == GDT_ENTRY_TSS @@ -53,42 +57,52 @@ static bool ignored_gdt(unsigned int num) || num == GDT_ENTRY_DOUBLEFAULT_TSS); } -/*H:630 Once the Guest gave us new GDT entries, we fix them up a little. We +/*H:630 + * Once the Guest gave us new GDT entries, we fix them up a little. We * don't care if they're invalid: the worst that can happen is a General * Protection Fault in the Switcher when it restores a Guest segment register * which tries to use that entry. Then we kill the Guest for causing such a - * mess: the message will be "unhandled trap 256". */ + * mess: the message will be "unhandled trap 256". + */ static void fixup_gdt_table(struct lg_cpu *cpu, unsigned start, unsigned end) { unsigned int i; for (i = start; i < end; i++) { - /* We never copy these ones to real GDT, so we don't care what - * they say */ + /* + * We never copy these ones to real GDT, so we don't care what + * they say + */ if (ignored_gdt(i)) continue; - /* Segment descriptors contain a privilege level: the Guest is + /* + * Segment descriptors contain a privilege level: the Guest is * sometimes careless and leaves this as 0, even though it's - * running at privilege level 1. If so, we fix it here. */ + * running at privilege level 1. If so, we fix it here. + */ if ((cpu->arch.gdt[i].b & 0x00006000) == 0) cpu->arch.gdt[i].b |= (GUEST_PL << 13); - /* Each descriptor has an "accessed" bit. If we don't set it + /* + * Each descriptor has an "accessed" bit. If we don't set it * now, the CPU will try to set it when the Guest first loads * that entry into a segment register. But the GDT isn't - * writable by the Guest, so bad things can happen. */ + * writable by the Guest, so bad things can happen. + */ cpu->arch.gdt[i].b |= 0x00000100; } } -/*H:610 Like the IDT, we never simply use the GDT the Guest gives us. We keep +/*H:610 + * Like the IDT, we never simply use the GDT the Guest gives us. We keep * a GDT for each CPU, and copy across the Guest's entries each time we want to * run the Guest on that CPU. * * This routine is called at boot or modprobe time for each CPU to set up the * constant GDT entries: the ones which are the same no matter what Guest we're - * running. */ + * running. + */ void setup_default_gdt_entries(struct lguest_ro_state *state) { struct desc_struct *gdt = state->guest_gdt; @@ -98,30 +112,37 @@ void setup_default_gdt_entries(struct lguest_ro_state *state) gdt[GDT_ENTRY_LGUEST_CS] = FULL_EXEC_SEGMENT; gdt[GDT_ENTRY_LGUEST_DS] = FULL_SEGMENT; - /* The TSS segment refers to the TSS entry for this particular CPU. + /* + * The TSS segment refers to the TSS entry for this particular CPU. * Forgive the magic flags: the 0x8900 means the entry is Present, it's * privilege level 0 Available 386 TSS system segment, and the 0x67 - * means Saturn is eclipsed by Mercury in the twelfth house. */ + * means Saturn is eclipsed by Mercury in the twelfth house. + */ gdt[GDT_ENTRY_TSS].a = 0x00000067 | (tss << 16); gdt[GDT_ENTRY_TSS].b = 0x00008900 | (tss & 0xFF000000) | ((tss >> 16) & 0x000000FF); } -/* This routine sets up the initial Guest GDT for booting. All entries start - * as 0 (unusable). */ +/* + * This routine sets up the initial Guest GDT for booting. All entries start + * as 0 (unusable). + */ void setup_guest_gdt(struct lg_cpu *cpu) { - /* Start with full 0-4G segments... */ + /* + * Start with full 0-4G segments...except the Guest is allowed to use + * them, so set the privilege level appropriately in the flags. + */ cpu->arch.gdt[GDT_ENTRY_KERNEL_CS] = FULL_EXEC_SEGMENT; cpu->arch.gdt[GDT_ENTRY_KERNEL_DS] = FULL_SEGMENT; - /* ...except the Guest is allowed to use them, so set the privilege - * level appropriately in the flags. */ cpu->arch.gdt[GDT_ENTRY_KERNEL_CS].b |= (GUEST_PL << 13); cpu->arch.gdt[GDT_ENTRY_KERNEL_DS].b |= (GUEST_PL << 13); } -/*H:650 An optimization of copy_gdt(), for just the three "thead-local storage" - * entries. */ +/*H:650 + * An optimization of copy_gdt(), for just the three "thead-local storage" + * entries. + */ void copy_gdt_tls(const struct lg_cpu *cpu, struct desc_struct *gdt) { unsigned int i; @@ -130,26 +151,34 @@ void copy_gdt_tls(const struct lg_cpu *cpu, struct desc_struct *gdt) gdt[i] = cpu->arch.gdt[i]; } -/*H:640 When the Guest is run on a different CPU, or the GDT entries have - * changed, copy_gdt() is called to copy the Guest's GDT entries across to this - * CPU's GDT. */ +/*H:640 + * When the Guest is run on a different CPU, or the GDT entries have changed, + * copy_gdt() is called to copy the Guest's GDT entries across to this CPU's + * GDT. + */ void copy_gdt(const struct lg_cpu *cpu, struct desc_struct *gdt) { unsigned int i; - /* The default entries from setup_default_gdt_entries() are not - * replaced. See ignored_gdt() above. */ + /* + * The default entries from setup_default_gdt_entries() are not + * replaced. See ignored_gdt() above. + */ for (i = 0; i < GDT_ENTRIES; i++) if (!ignored_gdt(i)) gdt[i] = cpu->arch.gdt[i]; } -/*H:620 This is where the Guest asks us to load a new GDT entry - * (LHCALL_LOAD_GDT_ENTRY). We tweak the entry and copy it in. */ +/*H:620 + * This is where the Guest asks us to load a new GDT entry + * (LHCALL_LOAD_GDT_ENTRY). We tweak the entry and copy it in. + */ void load_guest_gdt_entry(struct lg_cpu *cpu, u32 num, u32 lo, u32 hi) { - /* We assume the Guest has the same number of GDT entries as the - * Host, otherwise we'd have to dynamically allocate the Guest GDT. */ + /* + * We assume the Guest has the same number of GDT entries as the + * Host, otherwise we'd have to dynamically allocate the Guest GDT. + */ if (num >= ARRAY_SIZE(cpu->arch.gdt)) kill_guest(cpu, "too many gdt entries %i", num); @@ -157,15 +186,19 @@ void load_guest_gdt_entry(struct lg_cpu *cpu, u32 num, u32 lo, u32 hi) cpu->arch.gdt[num].a = lo; cpu->arch.gdt[num].b = hi; fixup_gdt_table(cpu, num, num+1); - /* Mark that the GDT changed so the core knows it has to copy it again, - * even if the Guest is run on the same CPU. */ + /* + * Mark that the GDT changed so the core knows it has to copy it again, + * even if the Guest is run on the same CPU. + */ cpu->changed |= CHANGED_GDT; } -/* This is the fast-track version for just changing the three TLS entries. +/* + * This is the fast-track version for just changing the three TLS entries. * Remember that this happens on every context switch, so it's worth * optimizing. But wouldn't it be neater to have a single hypercall to cover - * both cases? */ + * both cases? + */ void guest_load_tls(struct lg_cpu *cpu, unsigned long gtls) { struct desc_struct *tls = &cpu->arch.gdt[GDT_ENTRY_TLS_MIN]; @@ -175,7 +208,6 @@ void guest_load_tls(struct lg_cpu *cpu, unsigned long gtls) /* Note that just the TLS entries have changed. */ cpu->changed |= CHANGED_GDT_TLS; } -/*:*/ /*H:660 * With this, we have finished the Host. diff --git a/drivers/lguest/x86/core.c b/drivers/lguest/x86/core.c index eaf722fe309..96f7d88ec7f 100644 --- a/drivers/lguest/x86/core.c +++ b/drivers/lguest/x86/core.c @@ -17,13 +17,15 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ -/*P:450 This file contains the x86-specific lguest code. It used to be all +/*P:450 + * This file contains the x86-specific lguest code. It used to be all * mixed in with drivers/lguest/core.c but several foolhardy code slashers * wrestled most of the dependencies out to here in preparation for porting * lguest to other architectures (see what I mean by foolhardy?). * * This also contains a couple of non-obvious setup and teardown pieces which - * were implemented after days of debugging pain. :*/ + * were implemented after days of debugging pain. +:*/ #include #include #include @@ -82,25 +84,33 @@ static DEFINE_PER_CPU(struct lg_cpu *, last_cpu); */ static void copy_in_guest_info(struct lg_cpu *cpu, struct lguest_pages *pages) { - /* Copying all this data can be quite expensive. We usually run the + /* + * Copying all this data can be quite expensive. We usually run the * same Guest we ran last time (and that Guest hasn't run anywhere else * meanwhile). If that's not the case, we pretend everything in the - * Guest has changed. */ + * Guest has changed. + */ if (__get_cpu_var(last_cpu) != cpu || cpu->last_pages != pages) { __get_cpu_var(last_cpu) = cpu; cpu->last_pages = pages; cpu->changed = CHANGED_ALL; } - /* These copies are pretty cheap, so we do them unconditionally: */ - /* Save the current Host top-level page directory. */ + /* + * These copies are pretty cheap, so we do them unconditionally: */ + /* Save the current Host top-level page directory. + */ pages->state.host_cr3 = __pa(current->mm->pgd); - /* Set up the Guest's page tables to see this CPU's pages (and no - * other CPU's pages). */ + /* + * Set up the Guest's page tables to see this CPU's pages (and no + * other CPU's pages). + */ map_switcher_in_guest(cpu, pages); - /* Set up the two "TSS" members which tell the CPU what stack to use + /* + * Set up the two "TSS" members which tell the CPU what stack to use * for traps which do directly into the Guest (ie. traps at privilege - * level 1). */ + * level 1). + */ pages->state.guest_tss.sp1 = cpu->esp1; pages->state.guest_tss.ss1 = cpu->ss1; @@ -125,40 +135,53 @@ static void run_guest_once(struct lg_cpu *cpu, struct lguest_pages *pages) /* This is a dummy value we need for GCC's sake. */ unsigned int clobber; - /* Copy the guest-specific information into this CPU's "struct - * lguest_pages". */ + /* + * Copy the guest-specific information into this CPU's "struct + * lguest_pages". + */ copy_in_guest_info(cpu, pages); - /* Set the trap number to 256 (impossible value). If we fault while + /* + * Set the trap number to 256 (impossible value). If we fault while * switching to the Guest (bad segment registers or bug), this will - * cause us to abort the Guest. */ + * cause us to abort the Guest. + */ cpu->regs->trapnum = 256; - /* Now: we push the "eflags" register on the stack, then do an "lcall". + /* + * Now: we push the "eflags" register on the stack, then do an "lcall". * This is how we change from using the kernel code segment to using * the dedicated lguest code segment, as well as jumping into the * Switcher. * * The lcall also pushes the old code segment (KERNEL_CS) onto the * stack, then the address of this call. This stack layout happens to - * exactly match the stack layout created by an interrupt... */ + * exactly match the stack layout created by an interrupt... + */ asm volatile("pushf; lcall *lguest_entry" - /* This is how we tell GCC that %eax ("a") and %ebx ("b") - * are changed by this routine. The "=" means output. */ + /* + * This is how we tell GCC that %eax ("a") and %ebx ("b") + * are changed by this routine. The "=" means output. + */ : "=a"(clobber), "=b"(clobber) - /* %eax contains the pages pointer. ("0" refers to the + /* + * %eax contains the pages pointer. ("0" refers to the * 0-th argument above, ie "a"). %ebx contains the * physical address of the Guest's top-level page - * directory. */ + * directory. + */ : "0"(pages), "1"(__pa(cpu->lg->pgdirs[cpu->cpu_pgd].pgdir)) - /* We tell gcc that all these registers could change, + /* + * We tell gcc that all these registers could change, * which means we don't have to save and restore them in - * the Switcher. */ + * the Switcher. + */ : "memory", "%edx", "%ecx", "%edi", "%esi"); } /*:*/ -/*M:002 There are hooks in the scheduler which we can register to tell when we +/*M:002 + * There are hooks in the scheduler which we can register to tell when we * get kicked off the CPU (preempt_notifier_register()). This would allow us * to lazily disable SYSENTER which would regain some performance, and should * also simplify copy_in_guest_info(). Note that we'd still need to restore @@ -166,56 +189,72 @@ static void run_guest_once(struct lg_cpu *cpu, struct lguest_pages *pages) * * We could also try using this hooks for PGE, but that might be too expensive. * - * The hooks were designed for KVM, but we can also put them to good use. :*/ + * The hooks were designed for KVM, but we can also put them to good use. +:*/ -/*H:040 This is the i386-specific code to setup and run the Guest. Interrupts - * are disabled: we own the CPU. */ +/*H:040 + * This is the i386-specific code to setup and run the Guest. Interrupts + * are disabled: we own the CPU. + */ void lguest_arch_run_guest(struct lg_cpu *cpu) { - /* Remember the awfully-named TS bit? If the Guest has asked to set it + /* + * Remember the awfully-named TS bit? If the Guest has asked to set it * we set it now, so we can trap and pass that trap to the Guest if it - * uses the FPU. */ + * uses the FPU. + */ if (cpu->ts) unlazy_fpu(current); - /* SYSENTER is an optimized way of doing system calls. We can't allow + /* + * SYSENTER is an optimized way of doing system calls. We can't allow * it because it always jumps to privilege level 0. A normal Guest * won't try it because we don't advertise it in CPUID, but a malicious * Guest (or malicious Guest userspace program) could, so we tell the - * CPU to disable it before running the Guest. */ + * CPU to disable it before running the Guest. + */ if (boot_cpu_has(X86_FEATURE_SEP)) wrmsr(MSR_IA32_SYSENTER_CS, 0, 0); - /* Now we actually run the Guest. It will return when something + /* + * Now we actually run the Guest. It will return when something * interesting happens, and we can examine its registers to see what it - * was doing. */ + * was doing. + */ run_guest_once(cpu, lguest_pages(raw_smp_processor_id())); - /* Note that the "regs" structure contains two extra entries which are + /* + * Note that the "regs" structure contains two extra entries which are * not really registers: a trap number which says what interrupt or * trap made the switcher code come back, and an error code which some - * traps set. */ + * traps set. + */ /* Restore SYSENTER if it's supposed to be on. */ if (boot_cpu_has(X86_FEATURE_SEP)) wrmsr(MSR_IA32_SYSENTER_CS, __KERNEL_CS, 0); - /* If the Guest page faulted, then the cr2 register will tell us the + /* + * If the Guest page faulted, then the cr2 register will tell us the * bad virtual address. We have to grab this now, because once we * re-enable interrupts an interrupt could fault and thus overwrite - * cr2, or we could even move off to a different CPU. */ + * cr2, or we could even move off to a different CPU. + */ if (cpu->regs->trapnum == 14) cpu->arch.last_pagefault = read_cr2(); - /* Similarly, if we took a trap because the Guest used the FPU, + /* + * Similarly, if we took a trap because the Guest used the FPU, * we have to restore the FPU it expects to see. * math_state_restore() may sleep and we may even move off to * a different CPU. So all the critical stuff should be done - * before this. */ + * before this. + */ else if (cpu->regs->trapnum == 7) math_state_restore(); } -/*H:130 Now we've examined the hypercall code; our Guest can make requests. +/*H:130 + * Now we've examined the hypercall code; our Guest can make requests. * Our Guest is usually so well behaved; it never tries to do things it isn't * allowed to, and uses hypercalls instead. Unfortunately, Linux's paravirtual * infrastructure isn't quite complete, because it doesn't contain replacements @@ -225,26 +264,33 @@ void lguest_arch_run_guest(struct lg_cpu *cpu) * * When the Guest uses one of these instructions, we get a trap (General * Protection Fault) and come here. We see if it's one of those troublesome - * instructions and skip over it. We return true if we did. */ + * instructions and skip over it. We return true if we did. + */ static int emulate_insn(struct lg_cpu *cpu) { u8 insn; unsigned int insnlen = 0, in = 0, shift = 0; - /* The eip contains the *virtual* address of the Guest's instruction: - * guest_pa just subtracts the Guest's page_offset. */ + /* + * The eip contains the *virtual* address of the Guest's instruction: + * guest_pa just subtracts the Guest's page_offset. + */ unsigned long physaddr = guest_pa(cpu, cpu->regs->eip); - /* This must be the Guest kernel trying to do something, not userspace! + /* + * This must be the Guest kernel trying to do something, not userspace! * The bottom two bits of the CS segment register are the privilege - * level. */ + * level. + */ if ((cpu->regs->cs & 3) != GUEST_PL) return 0; /* Decoding x86 instructions is icky. */ insn = lgread(cpu, physaddr, u8); - /* 0x66 is an "operand prefix". It means it's using the upper 16 bits - of the eax register. */ + /* + * 0x66 is an "operand prefix". It means it's using the upper 16 bits + * of the eax register. + */ if (insn == 0x66) { shift = 16; /* The instruction is 1 byte so far, read the next byte. */ @@ -252,8 +298,10 @@ static int emulate_insn(struct lg_cpu *cpu) insn = lgread(cpu, physaddr + insnlen, u8); } - /* We can ignore the lower bit for the moment and decode the 4 opcodes - * we need to emulate. */ + /* + * We can ignore the lower bit for the moment and decode the 4 opcodes + * we need to emulate. + */ switch (insn & 0xFE) { case 0xE4: /* in ,%al */ insnlen += 2; @@ -274,9 +322,11 @@ static int emulate_insn(struct lg_cpu *cpu) return 0; } - /* If it was an "IN" instruction, they expect the result to be read + /* + * If it was an "IN" instruction, they expect the result to be read * into %eax, so we change %eax. We always return all-ones, which - * traditionally means "there's nothing there". */ + * traditionally means "there's nothing there". + */ if (in) { /* Lower bit tells is whether it's a 16 or 32 bit access */ if (insn & 0x1) @@ -290,7 +340,8 @@ static int emulate_insn(struct lg_cpu *cpu) return 1; } -/* Our hypercalls mechanism used to be based on direct software interrupts. +/* + * Our hypercalls mechanism used to be based on direct software interrupts. * After Anthony's "Refactor hypercall infrastructure" kvm patch, we decided to * change over to using kvm hypercalls. * @@ -318,16 +369,20 @@ static int emulate_insn(struct lg_cpu *cpu) */ static void rewrite_hypercall(struct lg_cpu *cpu) { - /* This are the opcodes we use to patch the Guest. The opcode for "int + /* + * This are the opcodes we use to patch the Guest. The opcode for "int * $0x1f" is "0xcd 0x1f" but vmcall instruction is 3 bytes long, so we - * complete the sequence with a NOP (0x90). */ + * complete the sequence with a NOP (0x90). + */ u8 insn[3] = {0xcd, 0x1f, 0x90}; __lgwrite(cpu, guest_pa(cpu, cpu->regs->eip), insn, sizeof(insn)); - /* The above write might have caused a copy of that page to be made + /* + * The above write might have caused a copy of that page to be made * (if it was read-only). We need to make sure the Guest has * up-to-date pagetables. As this doesn't happen often, we can just - * drop them all. */ + * drop them all. + */ guest_pagetable_clear_all(cpu); } @@ -335,9 +390,11 @@ static bool is_hypercall(struct lg_cpu *cpu) { u8 insn[3]; - /* This must be the Guest kernel trying to do something. + /* + * This must be the Guest kernel trying to do something. * The bottom two bits of the CS segment register are the privilege - * level. */ + * level. + */ if ((cpu->regs->cs & 3) != GUEST_PL) return false; @@ -351,86 +408,105 @@ void lguest_arch_handle_trap(struct lg_cpu *cpu) { switch (cpu->regs->trapnum) { case 13: /* We've intercepted a General Protection Fault. */ - /* Check if this was one of those annoying IN or OUT + /* + * Check if this was one of those annoying IN or OUT * instructions which we need to emulate. If so, we just go - * back into the Guest after we've done it. */ + * back into the Guest after we've done it. + */ if (cpu->regs->errcode == 0) { if (emulate_insn(cpu)) return; } - /* If KVM is active, the vmcall instruction triggers a - * General Protection Fault. Normally it triggers an - * invalid opcode fault (6): */ + /* + * If KVM is active, the vmcall instruction triggers a General + * Protection Fault. Normally it triggers an invalid opcode + * fault (6): + */ case 6: - /* We need to check if ring == GUEST_PL and - * faulting instruction == vmcall. */ + /* + * We need to check if ring == GUEST_PL and faulting + * instruction == vmcall. + */ if (is_hypercall(cpu)) { rewrite_hypercall(cpu); return; } break; case 14: /* We've intercepted a Page Fault. */ - /* The Guest accessed a virtual address that wasn't mapped. + /* + * The Guest accessed a virtual address that wasn't mapped. * This happens a lot: we don't actually set up most of the page * tables for the Guest at all when we start: as it runs it asks * for more and more, and we set them up as required. In this * case, we don't even tell the Guest that the fault happened. * * The errcode tells whether this was a read or a write, and - * whether kernel or userspace code. */ + * whether kernel or userspace code. + */ if (demand_page(cpu, cpu->arch.last_pagefault, cpu->regs->errcode)) return; - /* OK, it's really not there (or not OK): the Guest needs to + /* + * OK, it's really not there (or not OK): the Guest needs to * know. We write out the cr2 value so it knows where the * fault occurred. * * Note that if the Guest were really messed up, this could * happen before it's done the LHCALL_LGUEST_INIT hypercall, so - * lg->lguest_data could be NULL */ + * lg->lguest_data could be NULL + */ if (cpu->lg->lguest_data && put_user(cpu->arch.last_pagefault, &cpu->lg->lguest_data->cr2)) kill_guest(cpu, "Writing cr2"); break; case 7: /* We've intercepted a Device Not Available fault. */ - /* If the Guest doesn't want to know, we already restored the - * Floating Point Unit, so we just continue without telling - * it. */ + /* + * If the Guest doesn't want to know, we already restored the + * Floating Point Unit, so we just continue without telling it. + */ if (!cpu->ts) return; break; case 32 ... 255: - /* These values mean a real interrupt occurred, in which case + /* + * These values mean a real interrupt occurred, in which case * the Host handler has already been run. We just do a * friendly check if another process should now be run, then - * return to run the Guest again */ + * return to run the Guest again + */ cond_resched(); return; case LGUEST_TRAP_ENTRY: - /* Our 'struct hcall_args' maps directly over our regs: we set - * up the pointer now to indicate a hypercall is pending. */ + /* + * Our 'struct hcall_args' maps directly over our regs: we set + * up the pointer now to indicate a hypercall is pending. + */ cpu->hcall = (struct hcall_args *)cpu->regs; return; } /* We didn't handle the trap, so it needs to go to the Guest. */ if (!deliver_trap(cpu, cpu->regs->trapnum)) - /* If the Guest doesn't have a handler (either it hasn't + /* + * If the Guest doesn't have a handler (either it hasn't * registered any yet, or it's one of the faults we don't let - * it handle), it dies with this cryptic error message. */ + * it handle), it dies with this cryptic error message. + */ kill_guest(cpu, "unhandled trap %li at %#lx (%#lx)", cpu->regs->trapnum, cpu->regs->eip, cpu->regs->trapnum == 14 ? cpu->arch.last_pagefault : cpu->regs->errcode); } -/* Now we can look at each of the routines this calls, in increasing order of +/* + * Now we can look at each of the routines this calls, in increasing order of * complexity: do_hypercalls(), emulate_insn(), maybe_do_interrupt(), * deliver_trap() and demand_page(). After all those, we'll be ready to * examine the Switcher, and our philosophical understanding of the Host/Guest - * duality will be complete. :*/ + * duality will be complete. +:*/ static void adjust_pge(void *on) { if (on) @@ -439,13 +515,16 @@ static void adjust_pge(void *on) write_cr4(read_cr4() & ~X86_CR4_PGE); } -/*H:020 Now the Switcher is mapped and every thing else is ready, we need to do - * some more i386-specific initialization. */ +/*H:020 + * Now the Switcher is mapped and every thing else is ready, we need to do + * some more i386-specific initialization. + */ void __init lguest_arch_host_init(void) { int i; - /* Most of the i386/switcher.S doesn't care that it's been moved; on + /* + * Most of the i386/switcher.S doesn't care that it's been moved; on * Intel, jumps are relative, and it doesn't access any references to * external code or data. * @@ -453,7 +532,8 @@ void __init lguest_arch_host_init(void) * addresses are placed in a table (default_idt_entries), so we need to * update the table with the new addresses. switcher_offset() is a * convenience function which returns the distance between the - * compiled-in switcher code and the high-mapped copy we just made. */ + * compiled-in switcher code and the high-mapped copy we just made. + */ for (i = 0; i < IDT_ENTRIES; i++) default_idt_entries[i] += switcher_offset(); @@ -468,63 +548,81 @@ void __init lguest_arch_host_init(void) for_each_possible_cpu(i) { /* lguest_pages() returns this CPU's two pages. */ struct lguest_pages *pages = lguest_pages(i); - /* This is a convenience pointer to make the code fit one - * statement to a line. */ + /* This is a convenience pointer to make the code neater. */ struct lguest_ro_state *state = &pages->state; - /* The Global Descriptor Table: the Host has a different one + /* + * The Global Descriptor Table: the Host has a different one * for each CPU. We keep a descriptor for the GDT which says * where it is and how big it is (the size is actually the last - * byte, not the size, hence the "-1"). */ + * byte, not the size, hence the "-1"). + */ state->host_gdt_desc.size = GDT_SIZE-1; state->host_gdt_desc.address = (long)get_cpu_gdt_table(i); - /* All CPUs on the Host use the same Interrupt Descriptor + /* + * All CPUs on the Host use the same Interrupt Descriptor * Table, so we just use store_idt(), which gets this CPU's IDT - * descriptor. */ + * descriptor. + */ store_idt(&state->host_idt_desc); - /* The descriptors for the Guest's GDT and IDT can be filled + /* + * The descriptors for the Guest's GDT and IDT can be filled * out now, too. We copy the GDT & IDT into ->guest_gdt and - * ->guest_idt before actually running the Guest. */ + * ->guest_idt before actually running the Guest. + */ state->guest_idt_desc.size = sizeof(state->guest_idt)-1; state->guest_idt_desc.address = (long)&state->guest_idt; state->guest_gdt_desc.size = sizeof(state->guest_gdt)-1; state->guest_gdt_desc.address = (long)&state->guest_gdt; - /* We know where we want the stack to be when the Guest enters + /* + * We know where we want the stack to be when the Guest enters * the Switcher: in pages->regs. The stack grows upwards, so - * we start it at the end of that structure. */ + * we start it at the end of that structure. + */ state->guest_tss.sp0 = (long)(&pages->regs + 1); - /* And this is the GDT entry to use for the stack: we keep a - * couple of special LGUEST entries. */ + /* + * And this is the GDT entry to use for the stack: we keep a + * couple of special LGUEST entries. + */ state->guest_tss.ss0 = LGUEST_DS; - /* x86 can have a finegrained bitmap which indicates what I/O + /* + * x86 can have a finegrained bitmap which indicates what I/O * ports the process can use. We set it to the end of our - * structure, meaning "none". */ + * structure, meaning "none". + */ state->guest_tss.io_bitmap_base = sizeof(state->guest_tss); - /* Some GDT entries are the same across all Guests, so we can - * set them up now. */ + /* + * Some GDT entries are the same across all Guests, so we can + * set them up now. + */ setup_default_gdt_entries(state); /* Most IDT entries are the same for all Guests, too.*/ setup_default_idt_entries(state, default_idt_entries); - /* The Host needs to be able to use the LGUEST segments on this - * CPU, too, so put them in the Host GDT. */ + /* + * The Host needs to be able to use the LGUEST segments on this + * CPU, too, so put them in the Host GDT. + */ get_cpu_gdt_table(i)[GDT_ENTRY_LGUEST_CS] = FULL_EXEC_SEGMENT; get_cpu_gdt_table(i)[GDT_ENTRY_LGUEST_DS] = FULL_SEGMENT; } - /* In the Switcher, we want the %cs segment register to use the + /* + * In the Switcher, we want the %cs segment register to use the * LGUEST_CS GDT entry: we've put that in the Host and Guest GDTs, so * it will be undisturbed when we switch. To change %cs and jump we - * need this structure to feed to Intel's "lcall" instruction. */ + * need this structure to feed to Intel's "lcall" instruction. + */ lguest_entry.offset = (long)switch_to_guest + switcher_offset(); lguest_entry.segment = LGUEST_CS; - /* Finally, we need to turn off "Page Global Enable". PGE is an + /* + * Finally, we need to turn off "Page Global Enable". PGE is an * optimization where page table entries are specially marked to show * they never change. The Host kernel marks all the kernel pages this * way because it's always present, even when userspace is running. @@ -534,16 +632,21 @@ void __init lguest_arch_host_init(void) * you'll get really weird bugs that you'll chase for two days. * * I used to turn PGE off every time we switched to the Guest and back - * on when we return, but that slowed the Switcher down noticibly. */ + * on when we return, but that slowed the Switcher down noticibly. + */ - /* We don't need the complexity of CPUs coming and going while we're - * doing this. */ + /* + * We don't need the complexity of CPUs coming and going while we're + * doing this. + */ get_online_cpus(); if (cpu_has_pge) { /* We have a broader idea of "global". */ /* Remember that this was originally set (for cleanup). */ cpu_had_pge = 1; - /* adjust_pge is a helper function which sets or unsets the PGE - * bit on its CPU, depending on the argument (0 == unset). */ + /* + * adjust_pge is a helper function which sets or unsets the PGE + * bit on its CPU, depending on the argument (0 == unset). + */ on_each_cpu(adjust_pge, (void *)0, 1); /* Turn off the feature in the global feature set. */ clear_cpu_cap(&boot_cpu_data, X86_FEATURE_PGE); @@ -590,26 +693,32 @@ int lguest_arch_init_hypercalls(struct lg_cpu *cpu) { u32 tsc_speed; - /* The pointer to the Guest's "struct lguest_data" is the only argument. - * We check that address now. */ + /* + * The pointer to the Guest's "struct lguest_data" is the only argument. + * We check that address now. + */ if (!lguest_address_ok(cpu->lg, cpu->hcall->arg1, sizeof(*cpu->lg->lguest_data))) return -EFAULT; - /* Having checked it, we simply set lg->lguest_data to point straight + /* + * Having checked it, we simply set lg->lguest_data to point straight * into the Launcher's memory at the right place and then use * copy_to_user/from_user from now on, instead of lgread/write. I put * this in to show that I'm not immune to writing stupid - * optimizations. */ + * optimizations. + */ cpu->lg->lguest_data = cpu->lg->mem_base + cpu->hcall->arg1; - /* We insist that the Time Stamp Counter exist and doesn't change with + /* + * We insist that the Time Stamp Counter exist and doesn't change with * cpu frequency. Some devious chip manufacturers decided that TSC * changes could be handled in software. I decided that time going * backwards might be good for benchmarks, but it's bad for users. * * We also insist that the TSC be stable: the kernel detects unreliable - * TSCs for its own purposes, and we use that here. */ + * TSCs for its own purposes, and we use that here. + */ if (boot_cpu_has(X86_FEATURE_CONSTANT_TSC) && !check_tsc_unstable()) tsc_speed = tsc_khz; else @@ -625,38 +734,47 @@ int lguest_arch_init_hypercalls(struct lg_cpu *cpu) } /*:*/ -/*L:030 lguest_arch_setup_regs() +/*L:030 + * lguest_arch_setup_regs() * * Most of the Guest's registers are left alone: we used get_zeroed_page() to - * allocate the structure, so they will be 0. */ + * allocate the structure, so they will be 0. + */ void lguest_arch_setup_regs(struct lg_cpu *cpu, unsigned long start) { struct lguest_regs *regs = cpu->regs; - /* There are four "segment" registers which the Guest needs to boot: + /* + * There are four "segment" registers which the Guest needs to boot: * The "code segment" register (cs) refers to the kernel code segment * __KERNEL_CS, and the "data", "extra" and "stack" segment registers * refer to the kernel data segment __KERNEL_DS. * * The privilege level is packed into the lower bits. The Guest runs - * at privilege level 1 (GUEST_PL).*/ + * at privilege level 1 (GUEST_PL). + */ regs->ds = regs->es = regs->ss = __KERNEL_DS|GUEST_PL; regs->cs = __KERNEL_CS|GUEST_PL; - /* The "eflags" register contains miscellaneous flags. Bit 1 (0x002) + /* + * The "eflags" register contains miscellaneous flags. Bit 1 (0x002) * is supposed to always be "1". Bit 9 (0x200) controls whether * interrupts are enabled. We always leave interrupts enabled while - * running the Guest. */ + * running the Guest. + */ regs->eflags = X86_EFLAGS_IF | 0x2; - /* The "Extended Instruction Pointer" register says where the Guest is - * running. */ + /* + * The "Extended Instruction Pointer" register says where the Guest is + * running. + */ regs->eip = start; - /* %esi points to our boot information, at physical address 0, so don't - * touch it. */ + /* + * %esi points to our boot information, at physical address 0, so don't + * touch it. + */ - /* There are a couple of GDT entries the Guest expects when first - * booting. */ + /* There are a couple of GDT entries the Guest expects at boot. */ setup_guest_gdt(cpu); } diff --git a/drivers/lguest/x86/switcher_32.S b/drivers/lguest/x86/switcher_32.S index 3fc15318a80..6dec0979383 100644 --- a/drivers/lguest/x86/switcher_32.S +++ b/drivers/lguest/x86/switcher_32.S @@ -1,12 +1,15 @@ -/*P:900 This is the Switcher: code which sits at 0xFFC00000 astride both the +/*P:900 + * This is the Switcher: code which sits at 0xFFC00000 astride both the * Host and Guest to do the low-level Guest<->Host switch. It is as simple as * it can be made, but it's naturally very specific to x86. * * You have now completed Preparation. If this has whet your appetite; if you * are feeling invigorated and refreshed then the next, more challenging stage - * can be found in "make Guest". :*/ + * can be found in "make Guest". + :*/ -/*M:012 Lguest is meant to be simple: my rule of thumb is that 1% more LOC must +/*M:012 + * Lguest is meant to be simple: my rule of thumb is that 1% more LOC must * gain at least 1% more performance. Since neither LOC nor performance can be * measured beforehand, it generally means implementing a feature then deciding * if it's worth it. And once it's implemented, who can say no? @@ -31,11 +34,14 @@ * Host (which is actually really easy). * * Two questions remain. Would the performance gain outweigh the complexity? - * And who would write the verse documenting it? :*/ + * And who would write the verse documenting it? +:*/ -/*M:011 Lguest64 handles NMI. This gave me NMI envy (until I looked at their +/*M:011 + * Lguest64 handles NMI. This gave me NMI envy (until I looked at their * code). It's worth doing though, since it would let us use oprofile in the - * Host when a Guest is running. :*/ + * Host when a Guest is running. +:*/ /*S:100 * Welcome to the Switcher itself! diff --git a/include/linux/lguest.h b/include/linux/lguest.h index dbf2479e808..0a3a11afd64 100644 --- a/include/linux/lguest.h +++ b/include/linux/lguest.h @@ -1,5 +1,7 @@ -/* Things the lguest guest needs to know. Note: like all lguest interfaces, - * this is subject to wild and random change between versions. */ +/* + * Things the lguest guest needs to know. Note: like all lguest interfaces, + * this is subject to wild and random change between versions. + */ #ifndef _LINUX_LGUEST_H #define _LINUX_LGUEST_H @@ -11,32 +13,42 @@ #define LG_CLOCK_MIN_DELTA 100UL #define LG_CLOCK_MAX_DELTA ULONG_MAX -/*G:031 The second method of communicating with the Host is to via "struct +/*G:031 + * The second method of communicating with the Host is to via "struct * lguest_data". Once the Guest's initialization hypercall tells the Host where - * this is, the Guest and Host both publish information in it. :*/ + * this is, the Guest and Host both publish information in it. +:*/ struct lguest_data { - /* 512 == enabled (same as eflags in normal hardware). The Guest - * changes interrupts so often that a hypercall is too slow. */ + /* + * 512 == enabled (same as eflags in normal hardware). The Guest + * changes interrupts so often that a hypercall is too slow. + */ unsigned int irq_enabled; /* Fine-grained interrupt disabling by the Guest */ DECLARE_BITMAP(blocked_interrupts, LGUEST_IRQS); - /* The Host writes the virtual address of the last page fault here, + /* + * The Host writes the virtual address of the last page fault here, * which saves the Guest a hypercall. CR2 is the native register where - * this address would normally be found. */ + * this address would normally be found. + */ unsigned long cr2; /* Wallclock time set by the Host. */ struct timespec time; - /* Interrupt pending set by the Host. The Guest should do a hypercall - * if it re-enables interrupts and sees this set (to X86_EFLAGS_IF). */ + /* + * Interrupt pending set by the Host. The Guest should do a hypercall + * if it re-enables interrupts and sees this set (to X86_EFLAGS_IF). + */ int irq_pending; - /* Async hypercall ring. Instead of directly making hypercalls, we can + /* + * Async hypercall ring. Instead of directly making hypercalls, we can * place them in here for processing the next time the Host wants. - * This batching can be quite efficient. */ + * This batching can be quite efficient. + */ /* 0xFF == done (set by Host), 0 == pending (set by Guest). */ u8 hcall_status[LHCALL_RING_SIZE]; diff --git a/include/linux/lguest_launcher.h b/include/linux/lguest_launcher.h index bfefbdf7498..495203ff221 100644 --- a/include/linux/lguest_launcher.h +++ b/include/linux/lguest_launcher.h @@ -29,8 +29,10 @@ struct lguest_device_desc { __u8 type; /* The number of virtqueues (first in config array) */ __u8 num_vq; - /* The number of bytes of feature bits. Multiply by 2: one for host - * features and one for Guest acknowledgements. */ + /* + * The number of bytes of feature bits. Multiply by 2: one for host + * features and one for Guest acknowledgements. + */ __u8 feature_len; /* The number of bytes of the config array after virtqueues. */ __u8 config_len; @@ -39,8 +41,10 @@ struct lguest_device_desc { __u8 config[0]; }; -/*D:135 This is how we expect the device configuration field for a virtqueue - * to be laid out in config space. */ +/*D:135 + * This is how we expect the device configuration field for a virtqueue + * to be laid out in config space. + */ struct lguest_vqconfig { /* The number of entries in the virtio_ring */ __u16 num; @@ -61,7 +65,9 @@ enum lguest_req LHREQ_EVENTFD, /* + address, fd. */ }; -/* The alignment to use between consumer and producer parts of vring. - * x86 pagesize for historical reasons. */ +/* + * The alignment to use between consumer and producer parts of vring. + * x86 pagesize for historical reasons. + */ #define LGUEST_VRING_ALIGN 4096 #endif /* _LINUX_LGUEST_LAUNCHER */ -- GitLab From a91d74a3c4de8115295ee87350c13a329164aaaf Mon Sep 17 00:00:00 2001 From: Rusty Russell Date: Thu, 30 Jul 2009 16:03:45 -0600 Subject: [PATCH 0565/1342] lguest: update commentry Every so often, after code shuffles, I need to go through and unbitrot the Lguest Journey (see drivers/lguest/README). Since we now use RCU in a simple form in one place I took the opportunity to expand that explanation. Signed-off-by: Rusty Russell Cc: Ingo Molnar Cc: Paul McKenney --- Documentation/lguest/lguest.c | 184 +++++++++++++++++++++------- arch/x86/include/asm/lguest_hcall.h | 8 +- arch/x86/lguest/boot.c | 99 +++++++++++---- arch/x86/lguest/i386_head.S | 2 + drivers/lguest/core.c | 7 +- drivers/lguest/hypercalls.c | 6 +- drivers/lguest/lguest_device.c | 11 +- drivers/lguest/lguest_user.c | 100 +++++++++++++-- drivers/lguest/page_tables.c | 84 ++++++++++--- drivers/lguest/x86/core.c | 2 +- drivers/lguest/x86/switcher_32.S | 6 +- 11 files changed, 398 insertions(+), 111 deletions(-) diff --git a/Documentation/lguest/lguest.c b/Documentation/lguest/lguest.c index aa66a52b73e..45163651b51 100644 --- a/Documentation/lguest/lguest.c +++ b/Documentation/lguest/lguest.c @@ -49,7 +49,7 @@ #include "linux/virtio_ring.h" #include "asm/bootparam.h" /*L:110 - * We can ignore the 39 include files we need for this program, but I do want + * We can ignore the 42 include files we need for this program, but I do want * to draw attention to the use of kernel-style types. * * As Linus said, "C is a Spartan language, and so should your naming be." I @@ -305,6 +305,11 @@ static void *map_zeroed_pages(unsigned int num) PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE, fd, 0); if (addr == MAP_FAILED) err(1, "Mmaping %u pages of /dev/zero", num); + + /* + * One neat mmap feature is that you can close the fd, and it + * stays mapped. + */ close(fd); return addr; @@ -557,7 +562,7 @@ static void tell_kernel(unsigned long start) } /*:*/ -/* +/*L:200 * Device Handling. * * When the Guest gives us a buffer, it sends an array of addresses and sizes. @@ -608,7 +613,10 @@ static unsigned next_desc(struct vring_desc *desc, return next; } -/* This actually sends the interrupt for this virtqueue */ +/* + * This actually sends the interrupt for this virtqueue, if we've used a + * buffer. + */ static void trigger_irq(struct virtqueue *vq) { unsigned long buf[] = { LHREQ_IRQ, vq->config.irq }; @@ -629,12 +637,12 @@ static void trigger_irq(struct virtqueue *vq) } /* - * This looks in the virtqueue and for the first available buffer, and converts + * This looks in the virtqueue for the first available buffer, and converts * it to an iovec for convenient access. Since descriptors consist of some * number of output then some number of input descriptors, it's actually two * iovecs, but we pack them into one and note how many of each there were. * - * This function returns the descriptor number found. + * This function waits if necessary, and returns the descriptor number found. */ static unsigned wait_for_vq_desc(struct virtqueue *vq, struct iovec iov[], @@ -644,10 +652,14 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq, struct vring_desc *desc; u16 last_avail = lg_last_avail(vq); + /* There's nothing available? */ while (last_avail == vq->vring.avail->idx) { u64 event; - /* OK, tell Guest about progress up to now. */ + /* + * Since we're about to sleep, now is a good time to tell the + * Guest about what we've used up to now. + */ trigger_irq(vq); /* OK, now we need to know about added descriptors. */ @@ -734,8 +746,9 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq, } /* - * After we've used one of their buffers, we tell them about it. We'll then - * want to send them an interrupt, using trigger_irq(). + * After we've used one of their buffers, we tell the Guest about it. Sometime + * later we'll want to send them an interrupt using trigger_irq(); note that + * wait_for_vq_desc() does that for us if it has to wait. */ static void add_used(struct virtqueue *vq, unsigned int head, int len) { @@ -782,12 +795,12 @@ static void console_input(struct virtqueue *vq) struct console_abort *abort = vq->dev->priv; struct iovec iov[vq->vring.num]; - /* Make sure there's a descriptor waiting. */ + /* Make sure there's a descriptor available. */ head = wait_for_vq_desc(vq, iov, &out_num, &in_num); if (out_num) errx(1, "Output buffers in console in queue?"); - /* Read it in. */ + /* Read into it. This is where we usually wait. */ len = readv(STDIN_FILENO, iov, in_num); if (len <= 0) { /* Ran out of input? */ @@ -800,6 +813,7 @@ static void console_input(struct virtqueue *vq) pause(); } + /* Tell the Guest we used a buffer. */ add_used_and_trigger(vq, head, len); /* @@ -834,15 +848,23 @@ static void console_output(struct virtqueue *vq) unsigned int head, out, in; struct iovec iov[vq->vring.num]; + /* We usually wait in here, for the Guest to give us something. */ head = wait_for_vq_desc(vq, iov, &out, &in); if (in) errx(1, "Input buffers in console output queue?"); + + /* writev can return a partial write, so we loop here. */ while (!iov_empty(iov, out)) { int len = writev(STDOUT_FILENO, iov, out); if (len <= 0) err(1, "Write to stdout gave %i", len); iov_consume(iov, out, len); } + + /* + * We're finished with that buffer: if we're going to sleep, + * wait_for_vq_desc() will prod the Guest with an interrupt. + */ add_used(vq, head, 0); } @@ -862,15 +884,30 @@ static void net_output(struct virtqueue *vq) unsigned int head, out, in; struct iovec iov[vq->vring.num]; + /* We usually wait in here for the Guest to give us a packet. */ head = wait_for_vq_desc(vq, iov, &out, &in); if (in) errx(1, "Input buffers in net output queue?"); + /* + * Send the whole thing through to /dev/net/tun. It expects the exact + * same format: what a coincidence! + */ if (writev(net_info->tunfd, iov, out) < 0) errx(1, "Write to tun failed?"); + + /* + * Done with that one; wait_for_vq_desc() will send the interrupt if + * all packets are processed. + */ add_used(vq, head, 0); } -/* Will reading from this file descriptor block? */ +/* + * Handling network input is a bit trickier, because I've tried to optimize it. + * + * First we have a helper routine which tells is if from this file descriptor + * (ie. the /dev/net/tun device) will block: + */ static bool will_block(int fd) { fd_set fdset; @@ -880,7 +917,11 @@ static bool will_block(int fd) return select(fd+1, &fdset, NULL, NULL, &zero) != 1; } -/* This handles packets coming in from the tun device to our Guest. */ +/* + * This handles packets coming in from the tun device to our Guest. Like all + * service routines, it gets called again as soon as it returns, so you don't + * see a while(1) loop here. + */ static void net_input(struct virtqueue *vq) { int len; @@ -888,21 +929,38 @@ static void net_input(struct virtqueue *vq) struct iovec iov[vq->vring.num]; struct net_info *net_info = vq->dev->priv; + /* + * Get a descriptor to write an incoming packet into. This will also + * send an interrupt if they're out of descriptors. + */ head = wait_for_vq_desc(vq, iov, &out, &in); if (out) errx(1, "Output buffers in net input queue?"); - /* Deliver interrupt now, since we're about to sleep. */ + /* + * If it looks like we'll block reading from the tun device, send them + * an interrupt. + */ if (vq->pending_used && will_block(net_info->tunfd)) trigger_irq(vq); + /* + * Read in the packet. This is where we normally wait (when there's no + * incoming network traffic). + */ len = readv(net_info->tunfd, iov, in); if (len <= 0) err(1, "Failed to read from tun."); + + /* + * Mark that packet buffer as used, but don't interrupt here. We want + * to wait until we've done as much work as we can. + */ add_used(vq, head, len); } +/*:*/ -/* This is the helper to create threads. */ +/* This is the helper to create threads: run the service routine in a loop. */ static int do_thread(void *_vq) { struct virtqueue *vq = _vq; @@ -950,11 +1008,14 @@ static void reset_device(struct device *dev) signal(SIGCHLD, (void *)kill_launcher); } +/*L:216 + * This actually creates the thread which services the virtqueue for a device. + */ static void create_thread(struct virtqueue *vq) { /* - * Create stack for thread and run it. Since the stack grows upwards, - * we point the stack pointer to the end of this region. + * Create stack for thread. Since the stack grows upwards, we point + * the stack pointer to the end of this region. */ char *stack = malloc(32768); unsigned long args[] = { LHREQ_EVENTFD, @@ -966,17 +1027,22 @@ static void create_thread(struct virtqueue *vq) err(1, "Creating eventfd"); args[2] = vq->eventfd; - /* Attach an eventfd to this virtqueue: it will go off - * when the Guest does an LHCALL_NOTIFY for this vq. */ + /* + * Attach an eventfd to this virtqueue: it will go off when the Guest + * does an LHCALL_NOTIFY for this vq. + */ if (write(lguest_fd, &args, sizeof(args)) != 0) err(1, "Attaching eventfd"); - /* CLONE_VM: because it has to access the Guest memory, and - * SIGCHLD so we get a signal if it dies. */ + /* + * CLONE_VM: because it has to access the Guest memory, and SIGCHLD so + * we get a signal if it dies. + */ vq->thread = clone(do_thread, stack + 32768, CLONE_VM | SIGCHLD, vq); if (vq->thread == (pid_t)-1) err(1, "Creating clone"); - /* We close our local copy, now the child has it. */ + + /* We close our local copy now the child has it. */ close(vq->eventfd); } @@ -1028,7 +1094,10 @@ static void update_device_status(struct device *dev) } } -/* This is the generic routine we call when the Guest uses LHCALL_NOTIFY. */ +/*L:215 + * This is the generic routine we call when the Guest uses LHCALL_NOTIFY. In + * particular, it's used to notify us of device status changes during boot. + */ static void handle_output(unsigned long addr) { struct device *i; @@ -1037,18 +1106,32 @@ static void handle_output(unsigned long addr) for (i = devices.dev; i; i = i->next) { struct virtqueue *vq; - /* Notifications to device descriptors update device status. */ + /* + * Notifications to device descriptors mean they updated the + * device status. + */ if (from_guest_phys(addr) == i->desc) { update_device_status(i); return; } - /* Devices *can* be used before status is set to DRIVER_OK. */ + /* + * Devices *can* be used before status is set to DRIVER_OK. + * The original plan was that they would never do this: they + * would always finish setting up their status bits before + * actually touching the virtqueues. In practice, we allowed + * them to, and they do (eg. the disk probes for partition + * tables as part of initialization). + * + * If we see this, we start the device: once it's running, we + * expect the device to catch all the notifications. + */ for (vq = i->vq; vq; vq = vq->next) { if (addr != vq->config.pfn*getpagesize()) continue; if (i->running) errx(1, "Notification on running %s", i->name); + /* This just calls create_thread() for each virtqueue */ start_device(i); return; } @@ -1132,6 +1215,11 @@ static void add_virtqueue(struct device *dev, unsigned int num_descs, vq->next = NULL; vq->last_avail_idx = 0; vq->dev = dev; + + /* + * This is the routine the service thread will run, and its Process ID + * once it's running. + */ vq->service = service; vq->thread = (pid_t)-1; @@ -1202,7 +1290,8 @@ static void set_config(struct device *dev, unsigned len, const void *conf) /* * This routine does all the creation and setup of a new device, including - * calling new_dev_desc() to allocate the descriptor and device memory. + * calling new_dev_desc() to allocate the descriptor and device memory. We + * don't actually start the service threads until later. * * See what I mean about userspace being boring? */ @@ -1478,19 +1567,7 @@ static void setup_tun_net(char *arg) verbose("device %u: tun %s: %s\n", devices.device_num, tapif, arg); } - -/* - * Our block (disk) device should be really simple: the Guest asks for a block - * number and we read or write that position in the file. Unfortunately, that - * was amazingly slow: the Guest waits until the read is finished before - * running anything else, even if it could have been doing useful work. - * - * We could use async I/O, except it's reputed to suck so hard that characters - * actually go missing from your code when you try to use it. - * - * So this was one reason why lguest now does all virtqueue servicing in - * separate threads: it's more efficient and more like a real device. - */ +/*:*/ /* This hangs off device->priv. */ struct vblk_info @@ -1512,8 +1589,16 @@ struct vblk_info /*L:210 * The Disk * - * Remember that the block device is handled by a separate I/O thread. We head - * straight into the core of that thread here: + * The disk only has one virtqueue, so it only has one thread. It is really + * simple: the Guest asks for a block number and we read or write that position + * in the file. + * + * Before we serviced each virtqueue in a separate thread, that was unacceptably + * slow: the Guest waits until the read is finished before running anything + * else, even if it could have been doing useful work. + * + * We could have used async I/O, except it's reputed to suck so hard that + * characters actually go missing from your code when you try to use it. */ static void blk_request(struct virtqueue *vq) { @@ -1525,7 +1610,10 @@ static void blk_request(struct virtqueue *vq) struct iovec iov[vq->vring.num]; off64_t off; - /* Get the next request. */ + /* + * Get the next request, where we normally wait. It triggers the + * interrupt to acknowledge previously serviced requests (if any). + */ head = wait_for_vq_desc(vq, iov, &out_num, &in_num); /* @@ -1539,6 +1627,10 @@ static void blk_request(struct virtqueue *vq) out = convert(&iov[0], struct virtio_blk_outhdr); in = convert(&iov[out_num+in_num-1], u8); + /* + * For historical reasons, block operations are expressed in 512 byte + * "sectors". + */ off = out->sector * 512; /* @@ -1614,6 +1706,7 @@ static void blk_request(struct virtqueue *vq) if (out->type & VIRTIO_BLK_T_BARRIER) fdatasync(vblk->fd); + /* Finished that request. */ add_used(vq, head, wlen); } @@ -1682,9 +1775,8 @@ static void rng_input(struct virtqueue *vq) errx(1, "Output buffers in rng?"); /* - * This is why we convert to iovecs: the readv() call uses them, and so - * it reads straight into the Guest's buffer. We loop to make sure we - * fill it. + * Just like the console write, we loop to cover the whole iovec. + * In this case, short reads actually happen quite a bit. */ while (!iov_empty(iov, in_num)) { len = readv(rng_info->rfd, iov, in_num); @@ -1818,7 +1910,9 @@ int main(int argc, char *argv[]) devices.lastdev = NULL; devices.next_irq = 1; + /* We're CPU 0. In fact, that's the only CPU possible right now. */ cpu_id = 0; + /* * We need to know how much memory so we can set up the device * descriptor and memory pages for the devices as we parse the command @@ -1926,7 +2020,7 @@ int main(int argc, char *argv[]) */ tell_kernel(start); - /* Ensure that we terminate if a child dies. */ + /* Ensure that we terminate if a device-servicing child dies. */ signal(SIGCHLD, kill_launcher); /* If we exit via err(), this kills all the threads, restores tty. */ diff --git a/arch/x86/include/asm/lguest_hcall.h b/arch/x86/include/asm/lguest_hcall.h index cceb73e12e5..ba0eed8aa1a 100644 --- a/arch/x86/include/asm/lguest_hcall.h +++ b/arch/x86/include/asm/lguest_hcall.h @@ -35,10 +35,10 @@ * operations? There are two ways: the direct way is to make a "hypercall", * to make requests of the Host Itself. * - * We use the KVM hypercall mechanism. Seventeen hypercalls are - * available: the hypercall number is put in the %eax register, and the - * arguments (when required) are placed in %ebx, %ecx, %edx and %esi. - * If a return value makes sense, it's returned in %eax. + * We use the KVM hypercall mechanism, though completely different hypercall + * numbers. Seventeen hypercalls are available: the hypercall number is put in + * the %eax register, and the arguments (when required) are placed in %ebx, + * %ecx, %edx and %esi. If a return value makes sense, it's returned in %eax. * * Grossly invalid calls result in Sudden Death at the hands of the vengeful * Host, rather than returning failure. This reflects Winston Churchill's diff --git a/arch/x86/lguest/boot.c b/arch/x86/lguest/boot.c index 025c04d18f2..d677fa9ca65 100644 --- a/arch/x86/lguest/boot.c +++ b/arch/x86/lguest/boot.c @@ -154,6 +154,7 @@ static void lazy_hcall1(unsigned long call, async_hcall(call, arg1, 0, 0, 0); } +/* You can imagine what lazy_hcall2, 3 and 4 look like. :*/ static void lazy_hcall2(unsigned long call, unsigned long arg1, unsigned long arg2) @@ -189,8 +190,10 @@ static void lazy_hcall4(unsigned long call, } #endif -/* When lazy mode is turned off reset the per-cpu lazy mode variable and then - * issue the do-nothing hypercall to flush any stored calls. */ +/*G:036 + * When lazy mode is turned off reset the per-cpu lazy mode variable and then + * issue the do-nothing hypercall to flush any stored calls. +:*/ static void lguest_leave_lazy_mmu_mode(void) { kvm_hypercall0(LHCALL_FLUSH_ASYNC); @@ -250,13 +253,11 @@ extern void lg_irq_enable(void); extern void lg_restore_fl(unsigned long flags); /*M:003 - * Note that we don't check for outstanding interrupts when we re-enable them - * (or when we unmask an interrupt). This seems to work for the moment, since - * interrupts are rare and we'll just get the interrupt on the next timer tick, - * but now we can run with CONFIG_NO_HZ, we should revisit this. One way would - * be to put the "irq_enabled" field in a page by itself, and have the Host - * write-protect it when an interrupt comes in when irqs are disabled. There - * will then be a page fault as soon as interrupts are re-enabled. + * We could be more efficient in our checking of outstanding interrupts, rather + * than using a branch. One way would be to put the "irq_enabled" field in a + * page by itself, and have the Host write-protect it when an interrupt comes + * in when irqs are disabled. There will then be a page fault as soon as + * interrupts are re-enabled. * * A better method is to implement soft interrupt disable generally for x86: * instead of disabling interrupts, we set a flag. If an interrupt does come @@ -568,7 +569,7 @@ static void lguest_write_cr4(unsigned long val) * cr3 ---> +---------+ * | --------->+---------+ * | | | PADDR1 | - * Top-level | | PADDR2 | + * Mid-level | | PADDR2 | * (PMD) page | | | * | | Lower-level | * | | (PTE) page | @@ -588,23 +589,62 @@ static void lguest_write_cr4(unsigned long val) * Index into top Index into second Offset within page * page directory page pagetable page * - * The kernel spends a lot of time changing both the top-level page directory - * and lower-level pagetable pages. The Guest doesn't know physical addresses, - * so while it maintains these page tables exactly like normal, it also needs - * to keep the Host informed whenever it makes a change: the Host will create - * the real page tables based on the Guests'. + * Now, unfortunately, this isn't the whole story: Intel added Physical Address + * Extension (PAE) to allow 32 bit systems to use 64GB of memory (ie. 36 bits). + * These are held in 64-bit page table entries, so we can now only fit 512 + * entries in a page, and the neat three-level tree breaks down. + * + * The result is a four level page table: + * + * cr3 --> [ 4 Upper ] + * [ Level ] + * [ Entries ] + * [(PUD Page)]---> +---------+ + * | --------->+---------+ + * | | | PADDR1 | + * Mid-level | | PADDR2 | + * (PMD) page | | | + * | | Lower-level | + * | | (PTE) page | + * | | | | + * .... .... + * + * + * And the virtual address is decoded as: + * + * 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + * |<-2->|<--- 9 bits ---->|<---- 9 bits --->|<------ 12 bits ------>| + * Index into Index into mid Index into lower Offset within page + * top entries directory page pagetable page + * + * It's too hard to switch between these two formats at runtime, so Linux only + * supports one or the other depending on whether CONFIG_X86_PAE is set. Many + * distributions turn it on, and not just for people with silly amounts of + * memory: the larger PTE entries allow room for the NX bit, which lets the + * kernel disable execution of pages and increase security. + * + * This was a problem for lguest, which couldn't run on these distributions; + * then Matias Zabaljauregui figured it all out and implemented it, and only a + * handful of puppies were crushed in the process! + * + * Back to our point: the kernel spends a lot of time changing both the + * top-level page directory and lower-level pagetable pages. The Guest doesn't + * know physical addresses, so while it maintains these page tables exactly + * like normal, it also needs to keep the Host informed whenever it makes a + * change: the Host will create the real page tables based on the Guests'. */ /* - * The Guest calls this to set a second-level entry (pte), ie. to map a page - * into a process' address space. We set the entry then tell the Host the - * toplevel and address this corresponds to. The Guest uses one pagetable per - * process, so we need to tell the Host which one we're changing (mm->pgd). + * The Guest calls this after it has set a second-level entry (pte), ie. to map + * a page into a process' address space. Wetell the Host the toplevel and + * address this corresponds to. The Guest uses one pagetable per process, so + * we need to tell the Host which one we're changing (mm->pgd). */ static void lguest_pte_update(struct mm_struct *mm, unsigned long addr, pte_t *ptep) { #ifdef CONFIG_X86_PAE + /* PAE needs to hand a 64 bit page table entry, so it uses two args. */ lazy_hcall4(LHCALL_SET_PTE, __pa(mm->pgd), addr, ptep->pte_low, ptep->pte_high); #else @@ -612,6 +652,7 @@ static void lguest_pte_update(struct mm_struct *mm, unsigned long addr, #endif } +/* This is the "set and update" combo-meal-deal version. */ static void lguest_set_pte_at(struct mm_struct *mm, unsigned long addr, pte_t *ptep, pte_t pteval) { @@ -672,6 +713,11 @@ static void lguest_set_pte(pte_t *ptep, pte_t pteval) } #ifdef CONFIG_X86_PAE +/* + * With 64-bit PTE values, we need to be careful setting them: if we set 32 + * bits at a time, the hardware could see a weird half-set entry. These + * versions ensure we update all 64 bits at once. + */ static void lguest_set_pte_atomic(pte_t *ptep, pte_t pte) { native_set_pte_atomic(ptep, pte); @@ -679,13 +725,14 @@ static void lguest_set_pte_atomic(pte_t *ptep, pte_t pte) lazy_hcall1(LHCALL_FLUSH_TLB, 1); } -void lguest_pte_clear(struct mm_struct *mm, unsigned long addr, pte_t *ptep) +static void lguest_pte_clear(struct mm_struct *mm, unsigned long addr, + pte_t *ptep) { native_pte_clear(mm, addr, ptep); lguest_pte_update(mm, addr, ptep); } -void lguest_pmd_clear(pmd_t *pmdp) +static void lguest_pmd_clear(pmd_t *pmdp) { lguest_set_pmd(pmdp, __pmd(0)); } @@ -784,6 +831,14 @@ static void __init lguest_init_IRQ(void) irq_ctx_init(smp_processor_id()); } +/* + * With CONFIG_SPARSE_IRQ, interrupt descriptors are allocated as-needed, so + * rather than set them in lguest_init_IRQ we are called here every time an + * lguest device needs an interrupt. + * + * FIXME: irq_to_desc_alloc_node() can fail due to lack of memory, we should + * pass that up! + */ void lguest_setup_irq(unsigned int irq) { irq_to_desc_alloc_node(irq, 0); @@ -1298,7 +1353,7 @@ __init void lguest_init(void) */ switch_to_new_gdt(0); - /* As described in head_32.S, we map the first 128M of memory. */ + /* We actually boot with all memory mapped, but let's say 128MB. */ max_pfn_mapped = (128*1024*1024) >> PAGE_SHIFT; /* diff --git a/arch/x86/lguest/i386_head.S b/arch/x86/lguest/i386_head.S index db6aa95eb05..27eac0faee4 100644 --- a/arch/x86/lguest/i386_head.S +++ b/arch/x86/lguest/i386_head.S @@ -102,6 +102,7 @@ send_interrupts: * create one manually here. */ .byte 0x0f,0x01,0xc1 /* KVM_HYPERCALL */ + /* Put eax back the way we found it. */ popl %eax ret @@ -125,6 +126,7 @@ ENTRY(lg_restore_fl) jnz send_interrupts /* Again, the normal path has used no extra registers. Clever, huh? */ ret +/*:*/ /* These demark the EIP range where host should never deliver interrupts. */ .global lguest_noirq_start diff --git a/drivers/lguest/core.c b/drivers/lguest/core.c index cd058bc903f..1e2cb846b3c 100644 --- a/drivers/lguest/core.c +++ b/drivers/lguest/core.c @@ -217,10 +217,15 @@ int run_guest(struct lg_cpu *cpu, unsigned long __user *user) /* * It's possible the Guest did a NOTIFY hypercall to the - * Launcher, in which case we return from the read() now. + * Launcher. */ if (cpu->pending_notify) { + /* + * Does it just needs to write to a registered + * eventfd (ie. the appropriate virtqueue thread)? + */ if (!send_notify_to_eventfd(cpu)) { + /* OK, we tell the main Laucher. */ if (put_user(cpu->pending_notify, user)) return -EFAULT; return sizeof(cpu->pending_notify); diff --git a/drivers/lguest/hypercalls.c b/drivers/lguest/hypercalls.c index 787ab4bc09f..83511eb0923 100644 --- a/drivers/lguest/hypercalls.c +++ b/drivers/lguest/hypercalls.c @@ -59,7 +59,7 @@ static void do_hcall(struct lg_cpu *cpu, struct hcall_args *args) case LHCALL_SHUTDOWN: { char msg[128]; /* - * Shutdown is such a trivial hypercall that we do it in four + * Shutdown is such a trivial hypercall that we do it in five * lines right here. * * If the lgread fails, it will call kill_guest() itself; the @@ -245,6 +245,10 @@ static void initialize(struct lg_cpu *cpu) * device), the Guest will still see the old page. In practice, this never * happens: why would the Guest read a page which it has never written to? But * a similar scenario might one day bite us, so it's worth mentioning. + * + * Note that if we used a shared anonymous mapping in the Launcher instead of + * mapping /dev/zero private, we wouldn't worry about cop-on-write. And we + * need that to switch the Launcher to processes (away from threads) anyway. :*/ /*H:100 diff --git a/drivers/lguest/lguest_device.c b/drivers/lguest/lguest_device.c index cc000e79c3d..1401c1ace1e 100644 --- a/drivers/lguest/lguest_device.c +++ b/drivers/lguest/lguest_device.c @@ -236,7 +236,7 @@ static void lg_notify(struct virtqueue *vq) extern void lguest_setup_irq(unsigned int irq); /* - * This routine finds the first virtqueue described in the configuration of + * This routine finds the Nth virtqueue described in the configuration of * this device and sets it up. * * This is kind of an ugly duckling. It'd be nicer to have a standard @@ -244,9 +244,6 @@ extern void lguest_setup_irq(unsigned int irq); * everyone wants to do it differently. The KVM coders want the Guest to * allocate its own pages and tell the Host where they are, but for lguest it's * simpler for the Host to simply tell us where the pages are. - * - * So we provide drivers with a "find the Nth virtqueue and set it up" - * function. */ static struct virtqueue *lg_find_vq(struct virtio_device *vdev, unsigned index, @@ -422,7 +419,11 @@ static void add_lguest_device(struct lguest_device_desc *d, /* This devices' parent is the lguest/ dir. */ ldev->vdev.dev.parent = lguest_root; - /* We have a unique device index thanks to the dev_index counter. */ + /* + * The device type comes straight from the descriptor. There's also a + * device vendor field in the virtio_device struct, which we leave as + * 0. + */ ldev->vdev.id.device = d->type; /* * We have a simple set of routines for querying the device's diff --git a/drivers/lguest/lguest_user.c b/drivers/lguest/lguest_user.c index 7e92017103d..b4d3f7ca554 100644 --- a/drivers/lguest/lguest_user.c +++ b/drivers/lguest/lguest_user.c @@ -1,9 +1,8 @@ -/*P:200 - * This contains all the /dev/lguest code, whereby the userspace launcher +/*P:200 This contains all the /dev/lguest code, whereby the userspace launcher * controls and communicates with the Guest. For example, the first write will - * tell us the Guest's memory layout, pagetable, entry point and kernel address - * offset. A read will run the Guest until something happens, such as a signal - * or the Guest doing a NOTIFY out to the Launcher. + * tell us the Guest's memory layout and entry point. A read will run the + * Guest until something happens, such as a signal or the Guest doing a NOTIFY + * out to the Launcher. :*/ #include #include @@ -13,14 +12,41 @@ #include #include "lg.h" +/*L:056 + * Before we move on, let's jump ahead and look at what the kernel does when + * it needs to look up the eventfds. That will complete our picture of how we + * use RCU. + * + * The notification value is in cpu->pending_notify: we return true if it went + * to an eventfd. + */ bool send_notify_to_eventfd(struct lg_cpu *cpu) { unsigned int i; struct lg_eventfd_map *map; - /* lg->eventfds is RCU-protected */ + /* + * This "rcu_read_lock()" helps track when someone is still looking at + * the (RCU-using) eventfds array. It's not actually a lock at all; + * indeed it's a noop in many configurations. (You didn't expect me to + * explain all the RCU secrets here, did you?) + */ rcu_read_lock(); + /* + * rcu_dereference is the counter-side of rcu_assign_pointer(); it + * makes sure we don't access the memory pointed to by + * cpu->lg->eventfds before cpu->lg->eventfds is set. Sounds crazy, + * but Alpha allows this! Paul McKenney points out that a really + * aggressive compiler could have the same effect: + * http://lists.ozlabs.org/pipermail/lguest/2009-July/001560.html + * + * So play safe, use rcu_dereference to get the rcu-protected pointer: + */ map = rcu_dereference(cpu->lg->eventfds); + /* + * Simple array search: even if they add an eventfd while we do this, + * we'll continue to use the old array and just won't see the new one. + */ for (i = 0; i < map->num; i++) { if (map->map[i].addr == cpu->pending_notify) { eventfd_signal(map->map[i].event, 1); @@ -28,14 +54,43 @@ bool send_notify_to_eventfd(struct lg_cpu *cpu) break; } } + /* We're done with the rcu-protected variable cpu->lg->eventfds. */ rcu_read_unlock(); + + /* If we cleared the notification, it's because we found a match. */ return cpu->pending_notify == 0; } +/*L:055 + * One of the more tricksy tricks in the Linux Kernel is a technique called + * Read Copy Update. Since one point of lguest is to teach lguest journeyers + * about kernel coding, I use it here. (In case you're curious, other purposes + * include learning about virtualization and instilling a deep appreciation for + * simplicity and puppies). + * + * We keep a simple array which maps LHCALL_NOTIFY values to eventfds, but we + * add new eventfds without ever blocking readers from accessing the array. + * The current Launcher only does this during boot, so that never happens. But + * Read Copy Update is cool, and adding a lock risks damaging even more puppies + * than this code does. + * + * We allocate a brand new one-larger array, copy the old one and add our new + * element. Then we make the lg eventfd pointer point to the new array. + * That's the easy part: now we need to free the old one, but we need to make + * sure no slow CPU somewhere is still looking at it. That's what + * synchronize_rcu does for us: waits until every CPU has indicated that it has + * moved on to know it's no longer using the old one. + * + * If that's unclear, see http://en.wikipedia.org/wiki/Read-copy-update. + */ static int add_eventfd(struct lguest *lg, unsigned long addr, int fd) { struct lg_eventfd_map *new, *old = lg->eventfds; + /* + * We don't allow notifications on value 0 anyway (pending_notify of + * 0 means "nothing pending"). + */ if (!addr) return -EINVAL; @@ -62,12 +117,20 @@ static int add_eventfd(struct lguest *lg, unsigned long addr, int fd) } new->num++; - /* Now put new one in place. */ + /* + * Now put new one in place: rcu_assign_pointer() is a fancy way of + * doing "lg->eventfds = new", but it uses memory barriers to make + * absolutely sure that the contents of "new" written above is nailed + * down before we actually do the assignment. + * + * We have to think about these kinds of things when we're operating on + * live data without locks. + */ rcu_assign_pointer(lg->eventfds, new); /* * We're not in a big hurry. Wait until noone's looking at old - * version, then delete it. + * version, then free it. */ synchronize_rcu(); kfree(old); @@ -75,6 +138,14 @@ static int add_eventfd(struct lguest *lg, unsigned long addr, int fd) return 0; } +/*L:052 + * Receiving notifications from the Guest is usually done by attaching a + * particular LHCALL_NOTIFY value to an event filedescriptor. The eventfd will + * become readable when the Guest does an LHCALL_NOTIFY with that value. + * + * This is really convenient for processing each virtqueue in a separate + * thread. + */ static int attach_eventfd(struct lguest *lg, const unsigned long __user *input) { unsigned long addr, fd; @@ -86,6 +157,11 @@ static int attach_eventfd(struct lguest *lg, const unsigned long __user *input) if (get_user(fd, input) != 0) return -EFAULT; + /* + * Just make sure two callers don't add eventfds at once. We really + * only need to lock against callers adding to the same Guest, so using + * the Big Lguest Lock is overkill. But this is setup, not a fast path. + */ mutex_lock(&lguest_lock); err = add_eventfd(lg, addr, fd); mutex_unlock(&lguest_lock); @@ -106,6 +182,10 @@ static int user_send_irq(struct lg_cpu *cpu, const unsigned long __user *input) if (irq >= LGUEST_IRQS) return -EINVAL; + /* + * Next time the Guest runs, the core code will see if it can deliver + * this interrupt. + */ set_interrupt(cpu, irq); return 0; } @@ -307,10 +387,10 @@ unlock: * The first operation the Launcher does must be a write. All writes * start with an unsigned long number: for the first write this must be * LHREQ_INITIALIZE to set up the Guest. After that the Launcher can use - * writes of other values to send interrupts. + * writes of other values to send interrupts or set up receipt of notifications. * * Note that we overload the "offset" in the /dev/lguest file to indicate what - * CPU number we're dealing with. Currently this is always 0, since we only + * CPU number we're dealing with. Currently this is always 0 since we only * support uniprocessor Guests, but you can see the beginnings of SMP support * here. */ diff --git a/drivers/lguest/page_tables.c b/drivers/lguest/page_tables.c index 3da902e4b4c..a8d0aee3bc0 100644 --- a/drivers/lguest/page_tables.c +++ b/drivers/lguest/page_tables.c @@ -29,10 +29,10 @@ /*H:300 * The Page Table Code * - * We use two-level page tables for the Guest. If you're not entirely - * comfortable with virtual addresses, physical addresses and page tables then - * I recommend you review arch/x86/lguest/boot.c's "Page Table Handling" (with - * diagrams!). + * We use two-level page tables for the Guest, or three-level with PAE. If + * you're not entirely comfortable with virtual addresses, physical addresses + * and page tables then I recommend you review arch/x86/lguest/boot.c's "Page + * Table Handling" (with diagrams!). * * The Guest keeps page tables, but we maintain the actual ones here: these are * called "shadow" page tables. Which is a very Guest-centric name: these are @@ -52,9 +52,8 @@ :*/ /* - * 1024 entries in a page table page maps 1024 pages: 4MB. The Switcher is - * conveniently placed at the top 4MB, so it uses a separate, complete PTE - * page. + * The Switcher uses the complete top PTE page. That's 1024 PTE entries (4MB) + * or 512 PTE entries with PAE (2MB). */ #define SWITCHER_PGD_INDEX (PTRS_PER_PGD - 1) @@ -81,7 +80,8 @@ static DEFINE_PER_CPU(pte_t *, switcher_pte_pages); /*H:320 * The page table code is curly enough to need helper functions to keep it - * clear and clean. + * clear and clean. The kernel itself provides many of them; one advantage + * of insisting that the Guest and Host use the same CONFIG_PAE setting. * * There are two functions which return pointers to the shadow (aka "real") * page tables. @@ -155,7 +155,7 @@ static pte_t *spte_addr(struct lg_cpu *cpu, pgd_t spgd, unsigned long vaddr) } /* - * These two functions just like the above two, except they access the Guest + * These functions are just like the above two, except they access the Guest * page tables. Hence they return a Guest address. */ static unsigned long gpgd_addr(struct lg_cpu *cpu, unsigned long vaddr) @@ -165,6 +165,7 @@ static unsigned long gpgd_addr(struct lg_cpu *cpu, unsigned long vaddr) } #ifdef CONFIG_X86_PAE +/* Follow the PGD to the PMD. */ static unsigned long gpmd_addr(pgd_t gpgd, unsigned long vaddr) { unsigned long gpage = pgd_pfn(gpgd) << PAGE_SHIFT; @@ -172,6 +173,7 @@ static unsigned long gpmd_addr(pgd_t gpgd, unsigned long vaddr) return gpage + pmd_index(vaddr) * sizeof(pmd_t); } +/* Follow the PMD to the PTE. */ static unsigned long gpte_addr(struct lg_cpu *cpu, pmd_t gpmd, unsigned long vaddr) { @@ -181,6 +183,7 @@ static unsigned long gpte_addr(struct lg_cpu *cpu, return gpage + pte_index(vaddr) * sizeof(pte_t); } #else +/* Follow the PGD to the PTE (no mid-level for !PAE). */ static unsigned long gpte_addr(struct lg_cpu *cpu, pgd_t gpgd, unsigned long vaddr) { @@ -314,6 +317,7 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) pte_t gpte; pte_t *spte; + /* Mid level for PAE. */ #ifdef CONFIG_X86_PAE pmd_t *spmd; pmd_t gpmd; @@ -391,6 +395,8 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) */ gpte_ptr = gpte_addr(cpu, gpgd, vaddr); #endif + + /* Read the actual PTE value. */ gpte = lgread(cpu, gpte_ptr, pte_t); /* If this page isn't in the Guest page tables, we can't page it in. */ @@ -507,6 +513,7 @@ void pin_page(struct lg_cpu *cpu, unsigned long vaddr) if (!page_writable(cpu, vaddr) && !demand_page(cpu, vaddr, 2)) kill_guest(cpu, "bad stack page %#lx", vaddr); } +/*:*/ #ifdef CONFIG_X86_PAE static void release_pmd(pmd_t *spmd) @@ -543,7 +550,11 @@ static void release_pgd(pgd_t *spgd) } #else /* !CONFIG_X86_PAE */ -/*H:450 If we chase down the release_pgd() code, it looks like this: */ +/*H:450 + * If we chase down the release_pgd() code, the non-PAE version looks like + * this. The PAE version is almost identical, but instead of calling + * release_pte it calls release_pmd(), which looks much like this. + */ static void release_pgd(pgd_t *spgd) { /* If the entry's not present, there's nothing to release. */ @@ -898,17 +909,21 @@ void guest_set_pgd(struct lguest *lg, unsigned long gpgdir, u32 idx) /* ... throw it away. */ release_pgd(lg->pgdirs[pgdir].pgdir + idx); } + #ifdef CONFIG_X86_PAE +/* For setting a mid-level, we just throw everything away. It's easy. */ void guest_set_pmd(struct lguest *lg, unsigned long pmdp, u32 idx) { guest_pagetable_clear_all(&lg->cpus[0]); } #endif -/* - * Once we know how much memory we have we can construct simple identity (which +/*H:505 + * To get through boot, we construct simple identity page mappings (which * set virtual == physical) and linear mappings which will get the Guest far - * enough into the boot to create its own. + * enough into the boot to create its own. The linear mapping means we + * simplify the Guest boot, but it makes assumptions about their PAGE_OFFSET, + * as you'll see. * * We lay them out of the way, just below the initrd (which is why we need to * know its size here). @@ -944,6 +959,10 @@ static unsigned long setup_pagetables(struct lguest *lg, linear = (void *)pgdir - linear_pages * PAGE_SIZE; #ifdef CONFIG_X86_PAE + /* + * And the single mid page goes below that. We only use one, but + * that's enough to map 1G, which definitely gets us through boot. + */ pmds = (void *)linear - PAGE_SIZE; #endif /* @@ -957,13 +976,14 @@ static unsigned long setup_pagetables(struct lguest *lg, return -EFAULT; } +#ifdef CONFIG_X86_PAE /* - * The top level points to the linear page table pages above. - * We setup the identity and linear mappings here. + * Make the Guest PMD entries point to the corresponding place in the + * linear mapping (up to one page worth of PMD). */ -#ifdef CONFIG_X86_PAE for (i = j = 0; i < mapped_pages && j < PTRS_PER_PMD; i += PTRS_PER_PTE, j++) { + /* FIXME: native_set_pmd is overkill here. */ native_set_pmd(&pmd, __pmd(((unsigned long)(linear + i) - mem_base) | _PAGE_PRESENT | _PAGE_RW | _PAGE_USER)); @@ -971,18 +991,36 @@ static unsigned long setup_pagetables(struct lguest *lg, return -EFAULT; } + /* One PGD entry, pointing to that PMD page. */ set_pgd(&pgd, __pgd(((u32)pmds - mem_base) | _PAGE_PRESENT)); + /* Copy it in as the first PGD entry (ie. addresses 0-1G). */ if (copy_to_user(&pgdir[0], &pgd, sizeof(pgd)) != 0) return -EFAULT; + /* + * And the third PGD entry (ie. addresses 3G-4G). + * + * FIXME: This assumes that PAGE_OFFSET for the Guest is 0xC0000000. + */ if (copy_to_user(&pgdir[3], &pgd, sizeof(pgd)) != 0) return -EFAULT; #else + /* + * The top level points to the linear page table pages above. + * We setup the identity and linear mappings here. + */ phys_linear = (unsigned long)linear - mem_base; for (i = 0; i < mapped_pages; i += PTRS_PER_PTE) { pgd_t pgd; + /* + * Create a PGD entry which points to the right part of the + * linear PTE pages. + */ pgd = __pgd((phys_linear + i * sizeof(pte_t)) | (_PAGE_PRESENT | _PAGE_RW | _PAGE_USER)); + /* + * Copy it into the PGD page at 0 and PAGE_OFFSET. + */ if (copy_to_user(&pgdir[i / PTRS_PER_PTE], &pgd, sizeof(pgd)) || copy_to_user(&pgdir[pgd_index(PAGE_OFFSET) + i / PTRS_PER_PTE], @@ -992,8 +1030,8 @@ static unsigned long setup_pagetables(struct lguest *lg, #endif /* - * We return the top level (guest-physical) address: remember where - * this is. + * We return the top level (guest-physical) address: we remember where + * this is to write it into lguest_data when the Guest initializes. */ return (unsigned long)pgdir - mem_base; } @@ -1031,7 +1069,9 @@ int init_guest_pagetable(struct lguest *lg) lg->pgdirs[0].pgdir = (pgd_t *)get_zeroed_page(GFP_KERNEL); if (!lg->pgdirs[0].pgdir) return -ENOMEM; + #ifdef CONFIG_X86_PAE + /* For PAE, we also create the initial mid-level. */ pgd = lg->pgdirs[0].pgdir; pmd_table = (pmd_t *) get_zeroed_page(GFP_KERNEL); if (!pmd_table) @@ -1040,11 +1080,13 @@ int init_guest_pagetable(struct lguest *lg) set_pgd(pgd + SWITCHER_PGD_INDEX, __pgd(__pa(pmd_table) | _PAGE_PRESENT)); #endif + + /* This is the current page table. */ lg->cpus[0].cpu_pgd = 0; return 0; } -/* When the Guest calls LHCALL_LGUEST_INIT we do more setup. */ +/*H:508 When the Guest calls LHCALL_LGUEST_INIT we do more setup. */ void page_table_guest_data_init(struct lg_cpu *cpu) { /* We get the kernel address: above this is all kernel memory. */ @@ -1105,12 +1147,16 @@ void map_switcher_in_guest(struct lg_cpu *cpu, struct lguest_pages *pages) pmd_t switcher_pmd; pmd_t *pmd_table; + /* FIXME: native_set_pmd is overkill here. */ native_set_pmd(&switcher_pmd, pfn_pmd(__pa(switcher_pte_page) >> PAGE_SHIFT, PAGE_KERNEL_EXEC)); + /* Figure out where the pmd page is, by reading the PGD, and converting + * it to a virtual address. */ pmd_table = __va(pgd_pfn(cpu->lg-> pgdirs[cpu->cpu_pgd].pgdir[SWITCHER_PGD_INDEX]) << PAGE_SHIFT); + /* Now write it into the shadow page table. */ native_set_pmd(&pmd_table[SWITCHER_PMD_INDEX], switcher_pmd); #else pgd_t switcher_pgd; diff --git a/drivers/lguest/x86/core.c b/drivers/lguest/x86/core.c index 96f7d88ec7f..6ae388849a3 100644 --- a/drivers/lguest/x86/core.c +++ b/drivers/lguest/x86/core.c @@ -187,7 +187,7 @@ static void run_guest_once(struct lg_cpu *cpu, struct lguest_pages *pages) * also simplify copy_in_guest_info(). Note that we'd still need to restore * things when we exit to Launcher userspace, but that's fairly easy. * - * We could also try using this hooks for PGE, but that might be too expensive. + * We could also try using these hooks for PGE, but that might be too expensive. * * The hooks were designed for KVM, but we can also put them to good use. :*/ diff --git a/drivers/lguest/x86/switcher_32.S b/drivers/lguest/x86/switcher_32.S index 6dec0979383..40634b0db9f 100644 --- a/drivers/lguest/x86/switcher_32.S +++ b/drivers/lguest/x86/switcher_32.S @@ -1,7 +1,7 @@ /*P:900 - * This is the Switcher: code which sits at 0xFFC00000 astride both the - * Host and Guest to do the low-level Guest<->Host switch. It is as simple as - * it can be made, but it's naturally very specific to x86. + * This is the Switcher: code which sits at 0xFFC00000 (or 0xFFE00000) astride + * both the Host and Guest to do the low-level Guest<->Host switch. It is as + * simple as it can be made, but it's naturally very specific to x86. * * You have now completed Preparation. If this has whet your appetite; if you * are feeling invigorated and refreshed then the next, more challenging stage -- GitLab From 1842f23c05b6a866be831aa60bc8a8731c58ddd0 Mon Sep 17 00:00:00 2001 From: Rusty Russell Date: Thu, 30 Jul 2009 16:03:46 -0600 Subject: [PATCH 0566/1342] lguest and virtio: cleanup struct definitions to Linux style. I've been doing this for years, and akpm picked me up on it about 12 months ago. lguest partly serves as example code, so let's do it Right. Also, remove two unused fields in struct vblk_info in the example launcher. Signed-off-by: Rusty Russell Cc: Ingo Molnar --- Documentation/lguest/lguest.c | 21 +++++---------------- drivers/lguest/lg.h | 9 +++------ drivers/lguest/lguest_device.c | 3 +-- include/linux/lguest.h | 3 +-- include/linux/virtio_blk.h | 6 ++---- include/linux/virtio_config.h | 3 +-- include/linux/virtio_net.h | 6 ++---- include/linux/virtio_ring.h | 12 ++++-------- 8 files changed, 19 insertions(+), 44 deletions(-) diff --git a/Documentation/lguest/lguest.c b/Documentation/lguest/lguest.c index 45163651b51..950cde6d6e5 100644 --- a/Documentation/lguest/lguest.c +++ b/Documentation/lguest/lguest.c @@ -93,8 +93,7 @@ static int lguest_fd; static unsigned int __thread cpu_id; /* This is our list of devices. */ -struct device_list -{ +struct device_list { /* Counter to assign interrupt numbers. */ unsigned int next_irq; @@ -114,8 +113,7 @@ struct device_list static struct device_list devices; /* The device structure describes a single device. */ -struct device -{ +struct device { /* The linked-list pointer. */ struct device *next; @@ -140,8 +138,7 @@ struct device }; /* The virtqueue structure describes a queue attached to a device. */ -struct virtqueue -{ +struct virtqueue { struct virtqueue *next; /* Which device owns me. */ @@ -779,8 +776,7 @@ static void add_used_and_trigger(struct virtqueue *vq, unsigned head, int len) * * We associate some data with the console for our exit hack. */ -struct console_abort -{ +struct console_abort { /* How many times have they hit ^C? */ int count; /* When did they start? */ @@ -1570,20 +1566,13 @@ static void setup_tun_net(char *arg) /*:*/ /* This hangs off device->priv. */ -struct vblk_info -{ +struct vblk_info { /* The size of the file. */ off64_t len; /* The file descriptor for the file. */ int fd; - /* IO thread listens on this file descriptor [0]. */ - int workpipe[2]; - - /* IO thread writes to this file descriptor to mark it done, then - * Launcher triggers interrupt to Guest. */ - int done_fd; }; /*L:210 diff --git a/drivers/lguest/lg.h b/drivers/lguest/lg.h index 74c0db691b5..bc28745d05a 100644 --- a/drivers/lguest/lg.h +++ b/drivers/lguest/lg.h @@ -16,15 +16,13 @@ void free_pagetables(void); int init_pagetables(struct page **switcher_page, unsigned int pages); -struct pgdir -{ +struct pgdir { unsigned long gpgdir; pgd_t *pgdir; }; /* We have two pages shared with guests, per cpu. */ -struct lguest_pages -{ +struct lguest_pages { /* This is the stack page mapped rw in guest */ char spare[PAGE_SIZE - sizeof(struct lguest_regs)]; struct lguest_regs regs; @@ -89,8 +87,7 @@ struct lg_eventfd_map { }; /* The private info the thread maintains about the guest. */ -struct lguest -{ +struct lguest { struct lguest_data __user *lguest_data; struct lg_cpu cpus[NR_CPUS]; unsigned int nr_cpus; diff --git a/drivers/lguest/lguest_device.c b/drivers/lguest/lguest_device.c index 1401c1ace1e..b6200bc39b5 100644 --- a/drivers/lguest/lguest_device.c +++ b/drivers/lguest/lguest_device.c @@ -207,8 +207,7 @@ static void lg_reset(struct virtio_device *vdev) */ /*D:140 This is the information we remember about each virtqueue. */ -struct lguest_vq_info -{ +struct lguest_vq_info { /* A copy of the information contained in the device config. */ struct lguest_vqconfig config; diff --git a/include/linux/lguest.h b/include/linux/lguest.h index 0a3a11afd64..2fb1dcbcb5a 100644 --- a/include/linux/lguest.h +++ b/include/linux/lguest.h @@ -18,8 +18,7 @@ * lguest_data". Once the Guest's initialization hypercall tells the Host where * this is, the Guest and Host both publish information in it. :*/ -struct lguest_data -{ +struct lguest_data { /* * 512 == enabled (same as eflags in normal hardware). The Guest * changes interrupts so often that a hypercall is too slow. diff --git a/include/linux/virtio_blk.h b/include/linux/virtio_blk.h index be7d255fc7c..8dab9f2b883 100644 --- a/include/linux/virtio_blk.h +++ b/include/linux/virtio_blk.h @@ -20,8 +20,7 @@ #define VIRTIO_BLK_ID_BYTES (sizeof(__u16[256])) /* IDENTIFY DATA */ -struct virtio_blk_config -{ +struct virtio_blk_config { /* The capacity (in 512-byte sectors). */ __u64 capacity; /* The maximum segment size (if VIRTIO_BLK_F_SIZE_MAX) */ @@ -50,8 +49,7 @@ struct virtio_blk_config #define VIRTIO_BLK_T_BARRIER 0x80000000 /* This is the first element of the read scatter-gather list. */ -struct virtio_blk_outhdr -{ +struct virtio_blk_outhdr { /* VIRTIO_BLK_T* */ __u32 type; /* io priority. */ diff --git a/include/linux/virtio_config.h b/include/linux/virtio_config.h index 99f514575f6..e547e3c8ee9 100644 --- a/include/linux/virtio_config.h +++ b/include/linux/virtio_config.h @@ -79,8 +79,7 @@ * the dev->feature bits if it wants. */ typedef void vq_callback_t(struct virtqueue *); -struct virtio_config_ops -{ +struct virtio_config_ops { void (*get)(struct virtio_device *vdev, unsigned offset, void *buf, unsigned len); void (*set)(struct virtio_device *vdev, unsigned offset, diff --git a/include/linux/virtio_net.h b/include/linux/virtio_net.h index 9c543d6ac53..d8dd539c9f4 100644 --- a/include/linux/virtio_net.h +++ b/include/linux/virtio_net.h @@ -31,8 +31,7 @@ #define VIRTIO_NET_S_LINK_UP 1 /* Link is up */ -struct virtio_net_config -{ +struct virtio_net_config { /* The config defining mac address (if VIRTIO_NET_F_MAC) */ __u8 mac[6]; /* See VIRTIO_NET_F_STATUS and VIRTIO_NET_S_* above */ @@ -41,8 +40,7 @@ struct virtio_net_config /* This is the first element of the scatter-gather list. If you don't * specify GSO or CSUM features, you can simply ignore the header. */ -struct virtio_net_hdr -{ +struct virtio_net_hdr { #define VIRTIO_NET_HDR_F_NEEDS_CSUM 1 // Use csum_start, csum_offset __u8 flags; #define VIRTIO_NET_HDR_GSO_NONE 0 // Not a GSO frame diff --git a/include/linux/virtio_ring.h b/include/linux/virtio_ring.h index 693e0ec5afa..e4d144b132b 100644 --- a/include/linux/virtio_ring.h +++ b/include/linux/virtio_ring.h @@ -30,8 +30,7 @@ #define VIRTIO_RING_F_INDIRECT_DESC 28 /* Virtio ring descriptors: 16 bytes. These can chain together via "next". */ -struct vring_desc -{ +struct vring_desc { /* Address (guest-physical). */ __u64 addr; /* Length. */ @@ -42,24 +41,21 @@ struct vring_desc __u16 next; }; -struct vring_avail -{ +struct vring_avail { __u16 flags; __u16 idx; __u16 ring[]; }; /* u32 is used here for ids for padding reasons. */ -struct vring_used_elem -{ +struct vring_used_elem { /* Index of start of used descriptor chain. */ __u32 id; /* Total length of the descriptor chain which was used (written to) */ __u32 len; }; -struct vring_used -{ +struct vring_used { __u16 flags; __u16 idx; struct vring_used_elem ring[]; -- GitLab From e624859e7eb6ae2930df3923af73406dc6ccdad8 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Mon, 27 Jul 2009 22:11:59 +0100 Subject: [PATCH 0567/1342] ARM: 5624/1: Document cache aliasing region Augment the memory.txt file for ARM to list the cache aliasing region ffff4000-fffffff. Signed-off-by: Linus Walleij Signed-off-by: Russell King --- Documentation/arm/memory.txt | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/arm/memory.txt b/Documentation/arm/memory.txt index 43cb1004d35..9d58c7c5edd 100644 --- a/Documentation/arm/memory.txt +++ b/Documentation/arm/memory.txt @@ -21,6 +21,8 @@ ffff8000 ffffffff copy_user_page / clear_user_page use. For SA11xx and Xscale, this is used to setup a minicache mapping. +ffff4000 ffffffff cache aliasing on ARMv6 and later CPUs. + ffff1000 ffff7fff Reserved. Platforms must not use this address range. -- GitLab From 3ef7143d2287b21e09e00a25a8cb4fbdcf0c6c4c Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= Date: Wed, 29 Jul 2009 19:31:30 +0100 Subject: [PATCH 0568/1342] ARM: 5627/1: Fix restoring of lr at the end of mcount MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit After ftrace_trace_function is called r1 is probably clobbered so don't try to use its value for restoring. This was introduced in v2.6.29~38^2~7 Signed-off-by: Uwe Kleine-König Signed-off-by: Russell King --- arch/arm/kernel/entry-common.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/kernel/entry-common.S b/arch/arm/kernel/entry-common.S index 366e5097a41..8c3de1a350b 100644 --- a/arch/arm/kernel/entry-common.S +++ b/arch/arm/kernel/entry-common.S @@ -148,7 +148,7 @@ trace: sub r0, r0, #MCOUNT_INSN_SIZE mov lr, pc mov pc, r2 - mov lr, r1 @ restore lr + ldr lr, [fp, #-4] @ restore lr ldmia sp!, {r0-r3, pc} #endif /* CONFIG_DYNAMIC_FTRACE */ -- GitLab From 320145fac91955ee35a6af7e1c2b42388a17b3d8 Mon Sep 17 00:00:00 2001 From: Yegor Yefremov Date: Thu, 9 Jul 2009 08:48:03 +0100 Subject: [PATCH 0569/1342] ARM: 5597/1: [PCI] reset all internal hardware prior PCI initialization Make software reset to avoid freeze if PCI bus was messed up Signed-off-by: Yegor Yefremov Acked-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mach-ks8695/pci.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm/mach-ks8695/pci.c b/arch/arm/mach-ks8695/pci.c index f5ebcc0fcab..78499667eb7 100644 --- a/arch/arm/mach-ks8695/pci.c +++ b/arch/arm/mach-ks8695/pci.c @@ -245,6 +245,9 @@ static int ks8695_pci_fault(unsigned long addr, unsigned int fsr, struct pt_regs static void __init ks8695_pci_preinit(void) { + /* make software reset to avoid freeze if PCI bus was messed up */ + __raw_writel(0x80000000, KS8695_PCI_VA + KS8695_PBCS); + /* stage 1 initialization, subid, subdevice = 0x0001 */ __raw_writel(0x00010001, KS8695_PCI_VA + KS8695_CRCSID); -- GitLab From 2163b1e616c41c286f5ab79912671cd4bf52057c Mon Sep 17 00:00:00 2001 From: Steven Whitehouse Date: Thu, 25 Jun 2009 16:30:26 +0100 Subject: [PATCH 0570/1342] GFS2: Shrink the shrinker This patch removes some of the special cases that the shrinker was trying to deal with. As a result we leave fewer items on the list and none at all which cannot be demoted. This makes the list scanning more efficient and solves some issues seen with large numbers of inodes. Signed-off-by: Steven Whitehouse --- fs/gfs2/glock.c | 23 +++++------------------ 1 file changed, 5 insertions(+), 18 deletions(-) diff --git a/fs/gfs2/glock.c b/fs/gfs2/glock.c index 297421c0427..fdb796c4f94 100644 --- a/fs/gfs2/glock.c +++ b/fs/gfs2/glock.c @@ -1300,7 +1300,6 @@ static int gfs2_shrink_glock_memory(int nr, gfp_t gfp_mask) struct gfs2_glock *gl; int may_demote; int nr_skipped = 0; - int got_ref = 0; LIST_HEAD(skipped); if (nr == 0) @@ -1318,7 +1317,6 @@ static int gfs2_shrink_glock_memory(int nr, gfp_t gfp_mask) /* Test for being demotable */ if (!test_and_set_bit(GLF_LOCK, &gl->gl_flags)) { gfs2_glock_hold(gl); - got_ref = 1; spin_unlock(&lru_lock); spin_lock(&gl->gl_spin); may_demote = demote_ok(gl); @@ -1327,25 +1325,14 @@ static int gfs2_shrink_glock_memory(int nr, gfp_t gfp_mask) if (may_demote) { handle_callback(gl, LM_ST_UNLOCKED, 0); nr--; - if (queue_delayed_work(glock_workqueue, &gl->gl_work, 0) == 0) - gfs2_glock_put(gl); - got_ref = 0; } + if (queue_delayed_work(glock_workqueue, &gl->gl_work, 0) == 0) + gfs2_glock_put(gl); spin_lock(&lru_lock); - if (may_demote) - continue; - } - if (list_empty(&gl->gl_lru) && - (atomic_read(&gl->gl_ref) <= (2 + got_ref))) { - nr_skipped++; - list_add(&gl->gl_lru, &skipped); - } - if (got_ref) { - spin_unlock(&lru_lock); - gfs2_glock_put(gl); - spin_lock(&lru_lock); - got_ref = 0; + continue; } + nr_skipped++; + list_add(&gl->gl_lru, &skipped); } list_splice(&skipped, &lru_list); atomic_add(nr_skipped, &lru_count); -- GitLab From 1946f70ab5e4eb8b54a8eaaedba2293a3750ab7e Mon Sep 17 00:00:00 2001 From: Benjamin Marzinski Date: Thu, 25 Jun 2009 15:09:51 -0500 Subject: [PATCH 0571/1342] GFS2: keep statfs info in sync on grows GFS2 wasn't syncing its statfs info on grows. This causes a problem when you grow the filesystem on multiple nodes. GFS2 would calculate the new space based on the resource groups (which are always current), and then assume that the filesystem had grown the from the existing statfs size. If you grew the filesystem on two different nodes in a short time, the second node wouldn't see the statfs size change from the first node, and would assume that it was grown by a larger amount than it was. When all these changes were synced out, the total fileystem size would be incorrect (the first grow would be counted twice). This patch syncs makes GFS2 read in the statfs changes from disk before a grow, and write them out after the grow, while the master statfs inode is locked. Signed-off-by: Benjamin Marzinski Signed-off-by: Steven Whitehouse --- fs/gfs2/aops.c | 39 +++++++++++++++++++++++++++++++++++++++ fs/gfs2/super.c | 39 +++++++++++++++++++++++++-------------- fs/gfs2/super.h | 4 ++++ 3 files changed, 68 insertions(+), 14 deletions(-) diff --git a/fs/gfs2/aops.c b/fs/gfs2/aops.c index 03ebb439ace..7ebae9a4ecc 100644 --- a/fs/gfs2/aops.c +++ b/fs/gfs2/aops.c @@ -624,6 +624,7 @@ static int gfs2_write_begin(struct file *file, struct address_space *mapping, { struct gfs2_inode *ip = GFS2_I(mapping->host); struct gfs2_sbd *sdp = GFS2_SB(mapping->host); + struct gfs2_inode *m_ip = GFS2_I(sdp->sd_statfs_inode); unsigned int data_blocks = 0, ind_blocks = 0, rblocks; int alloc_required; int error = 0; @@ -637,6 +638,14 @@ static int gfs2_write_begin(struct file *file, struct address_space *mapping, error = gfs2_glock_nq(&ip->i_gh); if (unlikely(error)) goto out_uninit; + if (&ip->i_inode == sdp->sd_rindex) { + error = gfs2_glock_nq_init(m_ip->i_gl, LM_ST_EXCLUSIVE, + GL_NOCACHE, &m_ip->i_gh); + if (unlikely(error)) { + gfs2_glock_dq(&ip->i_gh); + goto out_uninit; + } + } error = gfs2_write_alloc_required(ip, pos, len, &alloc_required); if (error) @@ -667,6 +676,8 @@ static int gfs2_write_begin(struct file *file, struct address_space *mapping, rblocks += data_blocks ? data_blocks : 1; if (ind_blocks || data_blocks) rblocks += RES_STATFS + RES_QUOTA; + if (&ip->i_inode == sdp->sd_rindex) + rblocks += 2 * RES_STATFS; error = gfs2_trans_begin(sdp, rblocks, PAGE_CACHE_SIZE/sdp->sd_sb.sb_bsize); @@ -712,6 +723,10 @@ out_alloc_put: gfs2_alloc_put(ip); } out_unlock: + if (&ip->i_inode == sdp->sd_rindex) { + gfs2_glock_dq(&m_ip->i_gh); + gfs2_holder_uninit(&m_ip->i_gh); + } gfs2_glock_dq(&ip->i_gh); out_uninit: gfs2_holder_uninit(&ip->i_gh); @@ -725,14 +740,21 @@ out_uninit: static void adjust_fs_space(struct inode *inode) { struct gfs2_sbd *sdp = inode->i_sb->s_fs_info; + struct gfs2_inode *m_ip = GFS2_I(sdp->sd_statfs_inode); + struct gfs2_inode *l_ip = GFS2_I(sdp->sd_sc_inode); struct gfs2_statfs_change_host *m_sc = &sdp->sd_statfs_master; struct gfs2_statfs_change_host *l_sc = &sdp->sd_statfs_local; + struct buffer_head *m_bh, *l_bh; u64 fs_total, new_free; /* Total up the file system space, according to the latest rindex. */ fs_total = gfs2_ri_total(sdp); + if (gfs2_meta_inode_buffer(m_ip, &m_bh) != 0) + return; spin_lock(&sdp->sd_statfs_spin); + gfs2_statfs_change_in(m_sc, m_bh->b_data + + sizeof(struct gfs2_dinode)); if (fs_total > (m_sc->sc_total + l_sc->sc_total)) new_free = fs_total - (m_sc->sc_total + l_sc->sc_total); else @@ -741,6 +763,13 @@ static void adjust_fs_space(struct inode *inode) fs_warn(sdp, "File system extended by %llu blocks.\n", (unsigned long long)new_free); gfs2_statfs_change(sdp, new_free, new_free, 0); + + if (gfs2_meta_inode_buffer(l_ip, &l_bh) != 0) + goto out; + update_statfs(sdp, m_bh, l_bh); + brelse(l_bh); +out: + brelse(m_bh); } /** @@ -763,6 +792,7 @@ static int gfs2_stuffed_write_end(struct inode *inode, struct buffer_head *dibh, { struct gfs2_inode *ip = GFS2_I(inode); struct gfs2_sbd *sdp = GFS2_SB(inode); + struct gfs2_inode *m_ip = GFS2_I(sdp->sd_statfs_inode); u64 to = pos + copied; void *kaddr; unsigned char *buf = dibh->b_data + sizeof(struct gfs2_dinode); @@ -794,6 +824,10 @@ static int gfs2_stuffed_write_end(struct inode *inode, struct buffer_head *dibh, brelse(dibh); gfs2_trans_end(sdp); + if (inode == sdp->sd_rindex) { + gfs2_glock_dq(&m_ip->i_gh); + gfs2_holder_uninit(&m_ip->i_gh); + } gfs2_glock_dq(&ip->i_gh); gfs2_holder_uninit(&ip->i_gh); return copied; @@ -823,6 +857,7 @@ static int gfs2_write_end(struct file *file, struct address_space *mapping, struct inode *inode = page->mapping->host; struct gfs2_inode *ip = GFS2_I(inode); struct gfs2_sbd *sdp = GFS2_SB(inode); + struct gfs2_inode *m_ip = GFS2_I(sdp->sd_statfs_inode); struct buffer_head *dibh; struct gfs2_alloc *al = ip->i_alloc; unsigned int from = pos & (PAGE_CACHE_SIZE - 1); @@ -865,6 +900,10 @@ failed: gfs2_quota_unlock(ip); gfs2_alloc_put(ip); } + if (inode == sdp->sd_rindex) { + gfs2_glock_dq(&m_ip->i_gh); + gfs2_holder_uninit(&m_ip->i_gh); + } gfs2_glock_dq(&ip->i_gh); gfs2_holder_uninit(&ip->i_gh); return ret; diff --git a/fs/gfs2/super.c b/fs/gfs2/super.c index 0a680133647..552e321cee5 100644 --- a/fs/gfs2/super.c +++ b/fs/gfs2/super.c @@ -353,7 +353,7 @@ fail: return error; } -static void gfs2_statfs_change_in(struct gfs2_statfs_change_host *sc, const void *buf) +void gfs2_statfs_change_in(struct gfs2_statfs_change_host *sc, const void *buf) { const struct gfs2_statfs_change *str = buf; @@ -441,6 +441,29 @@ void gfs2_statfs_change(struct gfs2_sbd *sdp, s64 total, s64 free, brelse(l_bh); } +void update_statfs(struct gfs2_sbd *sdp, struct buffer_head *m_bh, + struct buffer_head *l_bh) +{ + struct gfs2_inode *m_ip = GFS2_I(sdp->sd_statfs_inode); + struct gfs2_inode *l_ip = GFS2_I(sdp->sd_sc_inode); + struct gfs2_statfs_change_host *m_sc = &sdp->sd_statfs_master; + struct gfs2_statfs_change_host *l_sc = &sdp->sd_statfs_local; + + gfs2_trans_add_bh(l_ip->i_gl, l_bh, 1); + + spin_lock(&sdp->sd_statfs_spin); + m_sc->sc_total += l_sc->sc_total; + m_sc->sc_free += l_sc->sc_free; + m_sc->sc_dinodes += l_sc->sc_dinodes; + memset(l_sc, 0, sizeof(struct gfs2_statfs_change)); + memset(l_bh->b_data + sizeof(struct gfs2_dinode), + 0, sizeof(struct gfs2_statfs_change)); + spin_unlock(&sdp->sd_statfs_spin); + + gfs2_trans_add_bh(m_ip->i_gl, m_bh, 1); + gfs2_statfs_change_out(m_sc, m_bh->b_data + sizeof(struct gfs2_dinode)); +} + int gfs2_statfs_sync(struct gfs2_sbd *sdp) { struct gfs2_inode *m_ip = GFS2_I(sdp->sd_statfs_inode); @@ -477,19 +500,7 @@ int gfs2_statfs_sync(struct gfs2_sbd *sdp) if (error) goto out_bh2; - gfs2_trans_add_bh(l_ip->i_gl, l_bh, 1); - - spin_lock(&sdp->sd_statfs_spin); - m_sc->sc_total += l_sc->sc_total; - m_sc->sc_free += l_sc->sc_free; - m_sc->sc_dinodes += l_sc->sc_dinodes; - memset(l_sc, 0, sizeof(struct gfs2_statfs_change)); - memset(l_bh->b_data + sizeof(struct gfs2_dinode), - 0, sizeof(struct gfs2_statfs_change)); - spin_unlock(&sdp->sd_statfs_spin); - - gfs2_trans_add_bh(m_ip->i_gl, m_bh, 1); - gfs2_statfs_change_out(m_sc, m_bh->b_data + sizeof(struct gfs2_dinode)); + update_statfs(sdp, m_bh, l_bh); gfs2_trans_end(sdp); diff --git a/fs/gfs2/super.h b/fs/gfs2/super.h index b56413e3e40..22e0417ed99 100644 --- a/fs/gfs2/super.h +++ b/fs/gfs2/super.h @@ -40,6 +40,10 @@ extern int gfs2_make_fs_rw(struct gfs2_sbd *sdp); extern int gfs2_statfs_init(struct gfs2_sbd *sdp); extern void gfs2_statfs_change(struct gfs2_sbd *sdp, s64 total, s64 free, s64 dinodes); +extern void gfs2_statfs_change_in(struct gfs2_statfs_change_host *sc, + const void *buf); +extern void update_statfs(struct gfs2_sbd *sdp, struct buffer_head *m_bh, + struct buffer_head *l_bh); extern int gfs2_statfs_sync(struct gfs2_sbd *sdp); extern int gfs2_freeze_fs(struct gfs2_sbd *sdp); -- GitLab From a51b56fff3f04fc5aa66b21a2a6d693ee9862d66 Mon Sep 17 00:00:00 2001 From: Benjamin Marzinski Date: Tue, 30 Jun 2009 13:51:11 -0500 Subject: [PATCH 0572/1342] GFS2: Fix panic in glock memory shrinker It is possible for gfs2_shrink_glock_memory() to check a glock for demotion that's in the process of being freed by gfs2_glock_put(). In this case, gfs2_shrink_glock_memory() will acquire a new reference to this glock, and then try to free the glock itself when it drops the refernce. To solve this, gfs2_shrink_glock_memory() just needs to check if the glock is in the process of being freed, and if so skip it without ever unlocking the lru_lock. Signed-off-by: Benjamin Marzinski Acked-by: Bob Peterson Signed-off-by: Steven Whitehouse --- fs/gfs2/glock.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/fs/gfs2/glock.c b/fs/gfs2/glock.c index fdb796c4f94..827136ee794 100644 --- a/fs/gfs2/glock.c +++ b/fs/gfs2/glock.c @@ -1314,6 +1314,10 @@ static int gfs2_shrink_glock_memory(int nr, gfp_t gfp_mask) list_del_init(&gl->gl_lru); atomic_dec(&lru_count); + /* Check if glock is about to be freed */ + if (atomic_read(&gl->gl_ref) == 0) + continue; + /* Test for being demotable */ if (!test_and_set_bit(GLF_LOCK, &gl->gl_flags)) { gfs2_glock_hold(gl); -- GitLab From 1e19a19584b332eb92a573b66b7342fb97e67507 Mon Sep 17 00:00:00 2001 From: Steven Whitehouse Date: Fri, 10 Jul 2009 21:13:38 +0100 Subject: [PATCH 0573/1342] GFS2: Don't try and dealloc own inode When searching for unlinked, but still allocated inodes during block allocation, avoid the block relating to the inode that is doing the allocation. This fixes a hang caused when an unlinked, but still open, inode tries to allocate some more blocks and lands up finding itself during the search for deallocatable inodes. Signed-off-by: Steven Whitehouse --- fs/gfs2/rgrp.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) diff --git a/fs/gfs2/rgrp.c b/fs/gfs2/rgrp.c index daa4ae341a2..5e5074176da 100644 --- a/fs/gfs2/rgrp.c +++ b/fs/gfs2/rgrp.c @@ -961,7 +961,8 @@ static int try_rgrp_fit(struct gfs2_rgrpd *rgd, struct gfs2_alloc *al) * Returns: The inode, if one has been found */ -static struct inode *try_rgrp_unlink(struct gfs2_rgrpd *rgd, u64 *last_unlinked) +static struct inode *try_rgrp_unlink(struct gfs2_rgrpd *rgd, u64 *last_unlinked, + u64 skip) { struct inode *inode; u32 goal = 0, block; @@ -985,6 +986,8 @@ static struct inode *try_rgrp_unlink(struct gfs2_rgrpd *rgd, u64 *last_unlinked) goal++; if (*last_unlinked != NO_BLOCK && no_addr <= *last_unlinked) continue; + if (no_addr == skip) + continue; *last_unlinked = no_addr; inode = gfs2_inode_lookup(rgd->rd_sbd->sd_vfs, DT_UNKNOWN, no_addr, -1, 1); @@ -1104,7 +1107,7 @@ static struct inode *get_local_rgrp(struct gfs2_inode *ip, u64 *last_unlinked) if (try_rgrp_fit(rgd, al)) goto out; if (rgd->rd_flags & GFS2_RDF_CHECK) - inode = try_rgrp_unlink(rgd, last_unlinked); + inode = try_rgrp_unlink(rgd, last_unlinked, ip->i_no_addr); if (!rg_locked) gfs2_glock_dq_uninit(&al->al_rgd_gh); if (inode) @@ -1138,7 +1141,7 @@ static struct inode *get_local_rgrp(struct gfs2_inode *ip, u64 *last_unlinked) if (try_rgrp_fit(rgd, al)) goto out; if (rgd->rd_flags & GFS2_RDF_CHECK) - inode = try_rgrp_unlink(rgd, last_unlinked); + inode = try_rgrp_unlink(rgd, last_unlinked, ip->i_no_addr); if (!rg_locked) gfs2_glock_dq_uninit(&al->al_rgd_gh); if (inode) -- GitLab From 8ff22a6f9bdaac87c0eeb1d56c736181f11b4221 Mon Sep 17 00:00:00 2001 From: Benjamin Marzinski Date: Fri, 10 Jul 2009 18:04:24 -0500 Subject: [PATCH 0574/1342] GFS2: Don't put unlikely reclaim candidates on the reclaim list. GFS2 was placing far too many glocks on the reclaim list that were not good candidates for freeing up from cache. These locks would sit there and repeatedly get scanned to see if they could be reclaimed, wasting a lot of time when there was memory pressure. This fix does more checks on the locks to see if they are actually likely to be removable from cache. Signed-off-by: Benjamin Marzinski Signed-off-by: Steven Whitehouse --- fs/gfs2/glock.c | 72 +++++++++++++++++++++++++++++++------------------ 1 file changed, 46 insertions(+), 26 deletions(-) diff --git a/fs/gfs2/glock.c b/fs/gfs2/glock.c index 827136ee794..f041a89e1ab 100644 --- a/fs/gfs2/glock.c +++ b/fs/gfs2/glock.c @@ -173,6 +173,26 @@ static void gfs2_glock_hold(struct gfs2_glock *gl) atomic_inc(&gl->gl_ref); } +/** + * demote_ok - Check to see if it's ok to unlock a glock + * @gl: the glock + * + * Returns: 1 if it's ok + */ + +static int demote_ok(const struct gfs2_glock *gl) +{ + const struct gfs2_glock_operations *glops = gl->gl_ops; + + if (gl->gl_state == LM_ST_UNLOCKED) + return 0; + if (!list_empty(&gl->gl_holders)) + return 0; + if (glops->go_demote_ok) + return glops->go_demote_ok(gl); + return 1; +} + /** * gfs2_glock_schedule_for_reclaim - Add a glock to the reclaim list * @gl: the glock @@ -181,14 +201,34 @@ static void gfs2_glock_hold(struct gfs2_glock *gl) static void gfs2_glock_schedule_for_reclaim(struct gfs2_glock *gl) { + int may_reclaim; + may_reclaim = (demote_ok(gl) && + (atomic_read(&gl->gl_ref) == 1 || + (gl->gl_name.ln_type == LM_TYPE_INODE && + atomic_read(&gl->gl_ref) <= 2))); spin_lock(&lru_lock); - if (list_empty(&gl->gl_lru) && gl->gl_state != LM_ST_UNLOCKED) { + if (list_empty(&gl->gl_lru) && may_reclaim) { list_add_tail(&gl->gl_lru, &lru_list); atomic_inc(&lru_count); } spin_unlock(&lru_lock); } +/** + * gfs2_glock_put_nolock() - Decrement reference count on glock + * @gl: The glock to put + * + * This function should only be used if the caller has its own reference + * to the glock, in addition to the one it is dropping. + */ + +static void gfs2_glock_put_nolock(struct gfs2_glock *gl) +{ + if (atomic_dec_and_test(&gl->gl_ref)) + GLOCK_BUG_ON(gl, 1); + gfs2_glock_schedule_for_reclaim(gl); +} + /** * gfs2_glock_put() - Decrement reference count on glock * @gl: The glock to put @@ -214,9 +254,9 @@ int gfs2_glock_put(struct gfs2_glock *gl) rv = 1; goto out; } - /* 1 for being hashed, 1 for having state != LM_ST_UNLOCKED */ - if (atomic_read(&gl->gl_ref) == 2) - gfs2_glock_schedule_for_reclaim(gl); + spin_lock(&gl->gl_spin); + gfs2_glock_schedule_for_reclaim(gl); + spin_unlock(&gl->gl_spin); write_unlock(gl_lock_addr(gl->gl_hash)); out: return rv; @@ -398,7 +438,7 @@ static void state_change(struct gfs2_glock *gl, unsigned int new_state) if (held2) gfs2_glock_hold(gl); else - gfs2_glock_put(gl); + gfs2_glock_put_nolock(gl); } gl->gl_state = new_state; @@ -633,7 +673,7 @@ out: out_sched: gfs2_glock_hold(gl); if (queue_delayed_work(glock_workqueue, &gl->gl_work, 0) == 0) - gfs2_glock_put(gl); + gfs2_glock_put_nolock(gl); out_unlock: clear_bit(GLF_LOCK, &gl->gl_flags); goto out; @@ -1274,26 +1314,6 @@ void gfs2_glock_complete(struct gfs2_glock *gl, int ret) gfs2_glock_put(gl); } -/** - * demote_ok - Check to see if it's ok to unlock a glock - * @gl: the glock - * - * Returns: 1 if it's ok - */ - -static int demote_ok(const struct gfs2_glock *gl) -{ - const struct gfs2_glock_operations *glops = gl->gl_ops; - - if (gl->gl_state == LM_ST_UNLOCKED) - return 0; - if (!list_empty(&gl->gl_holders)) - return 0; - if (glops->go_demote_ok) - return glops->go_demote_ok(gl); - return 1; -} - static int gfs2_shrink_glock_memory(int nr, gfp_t gfp_mask) { -- GitLab From 6b94617024bd6810cde1d0d491202c30d5a38d91 Mon Sep 17 00:00:00 2001 From: Benjamin Marzinski Date: Fri, 10 Jul 2009 18:13:26 -0500 Subject: [PATCH 0575/1342] GFS2: Fix incorrent statfs consistency check Since both linked and unlinked inodes are counted by rgd->rd_dinodes, It makes no sense to count them with the used data blocks (first check that I changed), it makes sense to count them with the linked inodes (second check), and it makes no sense to care if there are more unlinked inodes than linked ones. This fixes these errors. Signed-off-by: Benjamin Marzinski Signed-off-by: Steven Whitehouse --- fs/gfs2/rgrp.c | 14 +++----------- 1 file changed, 3 insertions(+), 11 deletions(-) diff --git a/fs/gfs2/rgrp.c b/fs/gfs2/rgrp.c index 5e5074176da..fba795798d3 100644 --- a/fs/gfs2/rgrp.c +++ b/fs/gfs2/rgrp.c @@ -285,27 +285,19 @@ void gfs2_rgrp_verify(struct gfs2_rgrpd *rgd) } tmp = rgd->rd_data - rgd->rd_free - rgd->rd_dinodes; - if (count[1] + count[2] != tmp) { + if (count[1] != tmp) { if (gfs2_consist_rgrpd(rgd)) fs_err(sdp, "used data mismatch: %u != %u\n", count[1], tmp); return; } - if (count[3] != rgd->rd_dinodes) { + if (count[2] + count[3] != rgd->rd_dinodes) { if (gfs2_consist_rgrpd(rgd)) fs_err(sdp, "used metadata mismatch: %u != %u\n", - count[3], rgd->rd_dinodes); + count[2] + count[3], rgd->rd_dinodes); return; } - - if (count[2] > count[3]) { - if (gfs2_consist_rgrpd(rgd)) - fs_err(sdp, "unlinked inodes > inodes: %u\n", - count[2]); - return; - } - } static inline int rgrp_contains_block(struct gfs2_rgrpd *rgd, u64 block) -- GitLab From b94a170e96dc416828af9d350ae2e34b70ae7347 Mon Sep 17 00:00:00 2001 From: Benjamin Marzinski Date: Thu, 23 Jul 2009 18:52:34 -0500 Subject: [PATCH 0576/1342] GFS2: remove dcache entries for remote deleted inodes When a file is deleted from a gfs2 filesystem on one node, a dcache entry for it may still exist on other nodes in the cluster. If this happens, gfs2 will be unable to free this file on disk. Because of this, it's possible to have a gfs2 filesystem with no files on it and no free space. With this patch, when a node receives a callback notifying it that the file is being deleted on another node, it schedules a new workqueue thread to remove the file's dcache entry. Signed-off-by: Benjamin Marzinski Signed-off-by: Steven Whitehouse --- fs/gfs2/glock.c | 43 ++++++++++++++++++++++++++++++++++++++----- fs/gfs2/glock.h | 3 +++ fs/gfs2/glops.c | 21 +++++++++++++++++++++ fs/gfs2/incore.h | 2 ++ fs/gfs2/super.c | 1 + 5 files changed, 65 insertions(+), 5 deletions(-) diff --git a/fs/gfs2/glock.c b/fs/gfs2/glock.c index f041a89e1ab..8b674b1f3a5 100644 --- a/fs/gfs2/glock.c +++ b/fs/gfs2/glock.c @@ -63,6 +63,7 @@ static void do_xmote(struct gfs2_glock *gl, struct gfs2_holder *gh, unsigned int static DECLARE_RWSEM(gfs2_umount_flush_sem); static struct dentry *gfs2_root; static struct workqueue_struct *glock_workqueue; +struct workqueue_struct *gfs2_delete_workqueue; static LIST_HEAD(lru_list); static atomic_t lru_count = ATOMIC_INIT(0); static DEFINE_SPINLOCK(lru_lock); @@ -167,7 +168,7 @@ static void glock_free(struct gfs2_glock *gl) * */ -static void gfs2_glock_hold(struct gfs2_glock *gl) +void gfs2_glock_hold(struct gfs2_glock *gl) { GLOCK_BUG_ON(gl, atomic_read(&gl->gl_ref) == 0); atomic_inc(&gl->gl_ref); @@ -222,7 +223,7 @@ static void gfs2_glock_schedule_for_reclaim(struct gfs2_glock *gl) * to the glock, in addition to the one it is dropping. */ -static void gfs2_glock_put_nolock(struct gfs2_glock *gl) +void gfs2_glock_put_nolock(struct gfs2_glock *gl) { if (atomic_dec_and_test(&gl->gl_ref)) GLOCK_BUG_ON(gl, 1); @@ -679,6 +680,29 @@ out_unlock: goto out; } +static void delete_work_func(struct work_struct *work) +{ + struct gfs2_glock *gl = container_of(work, struct gfs2_glock, gl_delete); + struct gfs2_sbd *sdp = gl->gl_sbd; + struct gfs2_inode *ip = NULL; + struct inode *inode; + u64 no_addr = 0; + + spin_lock(&gl->gl_spin); + ip = (struct gfs2_inode *)gl->gl_object; + if (ip) + no_addr = ip->i_no_addr; + spin_unlock(&gl->gl_spin); + if (ip) { + inode = gfs2_ilookup(sdp->sd_vfs, no_addr); + if (inode) { + d_prune_aliases(inode); + iput(inode); + } + } + gfs2_glock_put(gl); +} + static void glock_work_func(struct work_struct *work) { unsigned long delay = 0; @@ -757,6 +781,7 @@ int gfs2_glock_get(struct gfs2_sbd *sdp, u64 number, gl->gl_sbd = sdp; gl->gl_aspace = NULL; INIT_DELAYED_WORK(&gl->gl_work, glock_work_func); + INIT_WORK(&gl->gl_delete, delete_work_func); /* If this glock protects actual on-disk data or metadata blocks, create a VFS inode to manage the pages/buffers holding them. */ @@ -898,6 +923,8 @@ static void handle_callback(struct gfs2_glock *gl, unsigned int state, gl->gl_demote_state != state) { gl->gl_demote_state = LM_ST_UNLOCKED; } + if (gl->gl_ops->go_callback) + gl->gl_ops->go_callback(gl); trace_gfs2_demote_rq(gl); } @@ -1344,14 +1371,14 @@ static int gfs2_shrink_glock_memory(int nr, gfp_t gfp_mask) spin_unlock(&lru_lock); spin_lock(&gl->gl_spin); may_demote = demote_ok(gl); - spin_unlock(&gl->gl_spin); - clear_bit(GLF_LOCK, &gl->gl_flags); if (may_demote) { handle_callback(gl, LM_ST_UNLOCKED, 0); nr--; } if (queue_delayed_work(glock_workqueue, &gl->gl_work, 0) == 0) - gfs2_glock_put(gl); + gfs2_glock_put_nolock(gl); + spin_unlock(&gl->gl_spin); + clear_bit(GLF_LOCK, &gl->gl_flags); spin_lock(&lru_lock); continue; } @@ -1738,6 +1765,11 @@ int __init gfs2_glock_init(void) glock_workqueue = create_workqueue("glock_workqueue"); if (IS_ERR(glock_workqueue)) return PTR_ERR(glock_workqueue); + gfs2_delete_workqueue = create_workqueue("delete_workqueue"); + if (IS_ERR(gfs2_delete_workqueue)) { + destroy_workqueue(glock_workqueue); + return PTR_ERR(gfs2_delete_workqueue); + } register_shrinker(&glock_shrinker); @@ -1748,6 +1780,7 @@ void gfs2_glock_exit(void) { unregister_shrinker(&glock_shrinker); destroy_workqueue(glock_workqueue); + destroy_workqueue(gfs2_delete_workqueue); } static int gfs2_glock_iter_next(struct gfs2_glock_iter *gi) diff --git a/fs/gfs2/glock.h b/fs/gfs2/glock.h index a602a28f6f0..c609894ec0d 100644 --- a/fs/gfs2/glock.h +++ b/fs/gfs2/glock.h @@ -143,6 +143,7 @@ struct lm_lockops { #define GLR_TRYFAILED 13 +extern struct workqueue_struct *gfs2_delete_workqueue; static inline struct gfs2_holder *gfs2_glock_is_locked_by_me(struct gfs2_glock *gl) { struct gfs2_holder *gh; @@ -191,6 +192,8 @@ static inline int gfs2_glock_is_blocking(struct gfs2_glock *gl) int gfs2_glock_get(struct gfs2_sbd *sdp, u64 number, const struct gfs2_glock_operations *glops, int create, struct gfs2_glock **glp); +void gfs2_glock_hold(struct gfs2_glock *gl); +void gfs2_glock_put_nolock(struct gfs2_glock *gl); int gfs2_glock_put(struct gfs2_glock *gl); void gfs2_holder_init(struct gfs2_glock *gl, unsigned int state, unsigned flags, struct gfs2_holder *gh); diff --git a/fs/gfs2/glops.c b/fs/gfs2/glops.c index d5e4ab155ca..6985eef06c3 100644 --- a/fs/gfs2/glops.c +++ b/fs/gfs2/glops.c @@ -323,6 +323,7 @@ static void trans_go_sync(struct gfs2_glock *gl) if (gl->gl_state != LM_ST_UNLOCKED && test_bit(SDF_JOURNAL_LIVE, &sdp->sd_flags)) { + flush_workqueue(gfs2_delete_workqueue); gfs2_meta_syncfs(sdp); gfs2_log_shutdown(sdp); } @@ -372,6 +373,25 @@ static int trans_go_demote_ok(const struct gfs2_glock *gl) return 0; } +/** + * iopen_go_callback - schedule the dcache entry for the inode to be deleted + * @gl: the glock + * + * gl_spin lock is held while calling this + */ +static void iopen_go_callback(struct gfs2_glock *gl) +{ + struct gfs2_inode *ip = (struct gfs2_inode *)gl->gl_object; + + if (gl->gl_demote_state == LM_ST_UNLOCKED && + gl->gl_state == LM_ST_SHARED && + ip && test_bit(GIF_USER, &ip->i_flags)) { + gfs2_glock_hold(gl); + if (queue_work(gfs2_delete_workqueue, &gl->gl_delete) == 0) + gfs2_glock_put_nolock(gl); + } +} + const struct gfs2_glock_operations gfs2_meta_glops = { .go_type = LM_TYPE_META, }; @@ -406,6 +426,7 @@ const struct gfs2_glock_operations gfs2_trans_glops = { const struct gfs2_glock_operations gfs2_iopen_glops = { .go_type = LM_TYPE_IOPEN, + .go_callback = iopen_go_callback, }; const struct gfs2_glock_operations gfs2_flock_glops = { diff --git a/fs/gfs2/incore.h b/fs/gfs2/incore.h index 225347fbff3..61801ada36f 100644 --- a/fs/gfs2/incore.h +++ b/fs/gfs2/incore.h @@ -159,6 +159,7 @@ struct gfs2_glock_operations { int (*go_lock) (struct gfs2_holder *gh); void (*go_unlock) (struct gfs2_holder *gh); int (*go_dump)(struct seq_file *seq, const struct gfs2_glock *gl); + void (*go_callback) (struct gfs2_glock *gl); const int go_type; const unsigned long go_min_hold_time; }; @@ -228,6 +229,7 @@ struct gfs2_glock { struct list_head gl_ail_list; atomic_t gl_ail_count; struct delayed_work gl_work; + struct work_struct gl_delete; }; #define GFS2_MIN_LVB_SIZE 32 /* Min size of LVB that gfs2 supports */ diff --git a/fs/gfs2/super.c b/fs/gfs2/super.c index 552e321cee5..f522bb01797 100644 --- a/fs/gfs2/super.c +++ b/fs/gfs2/super.c @@ -691,6 +691,7 @@ static int gfs2_make_fs_ro(struct gfs2_sbd *sdp) struct gfs2_holder t_gh; int error; + flush_workqueue(gfs2_delete_workqueue); gfs2_quota_sync(sdp); gfs2_statfs_sync(sdp); -- GitLab From 276e680d192a67d222fcea51af37b056feffb665 Mon Sep 17 00:00:00 2001 From: Yan Zheng Date: Thu, 30 Jul 2009 09:40:40 -0400 Subject: [PATCH 0577/1342] Btrfs: preserve commit_root for async caching The async block group caching code uses the commit_root pointer to get a stable version of the extent allocation tree for scanning. This copy of the tree root isn't going to change and it significantly reduces the complexity of the scanning code. During a commit, we have a loop where we update the extent allocation tree root. We need to loop because updating the root pointer in the tree of tree roots may allocate blocks which may change the extent allocation tree. Right now the commit_root pointer is changed inside this loop. It is more correct to change the commit_root pointer only after all the looping is done. Signed-off-by: Yan Zheng Signed-off-by: Chris Mason --- fs/btrfs/ctree.h | 4 +--- fs/btrfs/disk-io.c | 2 +- fs/btrfs/extent-tree.c | 6 +++--- fs/btrfs/transaction.c | 12 +++++++++--- 4 files changed, 14 insertions(+), 10 deletions(-) diff --git a/fs/btrfs/ctree.h b/fs/btrfs/ctree.h index 17ad92c29cf..38eeb6c49c8 100644 --- a/fs/btrfs/ctree.h +++ b/fs/btrfs/ctree.h @@ -827,6 +827,7 @@ struct btrfs_fs_info { struct mutex drop_mutex; struct mutex volume_mutex; struct mutex tree_reloc_mutex; + struct rw_semaphore extent_commit_sem; /* * this protects the ordered operations list only while we are @@ -961,9 +962,6 @@ struct btrfs_root { /* the node lock is held while changing the node pointer */ spinlock_t node_lock; - /* taken when updating the commit root */ - struct rw_semaphore commit_root_sem; - struct extent_buffer *commit_root; struct btrfs_root *log_root; struct btrfs_root *reloc_root; diff --git a/fs/btrfs/disk-io.c b/fs/btrfs/disk-io.c index 3a9b8875988..3cf4cfa575c 100644 --- a/fs/btrfs/disk-io.c +++ b/fs/btrfs/disk-io.c @@ -907,7 +907,6 @@ static int __setup_root(u32 nodesize, u32 leafsize, u32 sectorsize, spin_lock_init(&root->inode_lock); mutex_init(&root->objectid_mutex); mutex_init(&root->log_mutex); - init_rwsem(&root->commit_root_sem); init_waitqueue_head(&root->log_writer_wait); init_waitqueue_head(&root->log_commit_wait[0]); init_waitqueue_head(&root->log_commit_wait[1]); @@ -1624,6 +1623,7 @@ struct btrfs_root *open_ctree(struct super_block *sb, mutex_init(&fs_info->cleaner_mutex); mutex_init(&fs_info->volume_mutex); mutex_init(&fs_info->tree_reloc_mutex); + init_rwsem(&fs_info->extent_commit_sem); btrfs_init_free_cluster(&fs_info->meta_alloc_cluster); btrfs_init_free_cluster(&fs_info->data_alloc_cluster); diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c index fadf69a2764..2fe21fa7491 100644 --- a/fs/btrfs/extent-tree.c +++ b/fs/btrfs/extent-tree.c @@ -267,7 +267,7 @@ static int caching_kthread(void *data) last = max_t(u64, block_group->key.objectid, BTRFS_SUPER_INFO_OFFSET); again: /* need to make sure the commit_root doesn't disappear */ - down_read(&fs_info->extent_root->commit_root_sem); + down_read(&fs_info->extent_commit_sem); /* * We don't want to deadlock with somebody trying to allocate a new @@ -304,7 +304,7 @@ again: if (need_resched()) { btrfs_release_path(fs_info->extent_root, path); - up_read(&fs_info->extent_root->commit_root_sem); + up_read(&fs_info->extent_commit_sem); cond_resched(); goto again; } @@ -345,7 +345,7 @@ next: err: btrfs_free_path(path); - up_read(&fs_info->extent_root->commit_root_sem); + up_read(&fs_info->extent_commit_sem); atomic_dec(&block_group->space_info->caching_threads); wake_up(&block_group->caching_q); diff --git a/fs/btrfs/transaction.c b/fs/btrfs/transaction.c index e51d2bc532f..de48e4ec808 100644 --- a/fs/btrfs/transaction.c +++ b/fs/btrfs/transaction.c @@ -42,10 +42,8 @@ static noinline void put_transaction(struct btrfs_transaction *transaction) static noinline void switch_commit_root(struct btrfs_root *root) { - down_write(&root->commit_root_sem); free_extent_buffer(root->commit_root); root->commit_root = btrfs_root_node(root); - up_write(&root->commit_root_sem); } /* @@ -466,7 +464,10 @@ static int update_cowonly_root(struct btrfs_trans_handle *trans, ret = btrfs_write_dirty_block_groups(trans, root); BUG_ON(ret); } - switch_commit_root(root); + + if (root != root->fs_info->extent_root) + switch_commit_root(root); + return 0; } @@ -499,6 +500,11 @@ static noinline int commit_cowonly_roots(struct btrfs_trans_handle *trans, update_cowonly_root(trans, root); } + + down_write(&fs_info->extent_commit_sem); + switch_commit_root(fs_info->extent_root); + up_write(&fs_info->extent_commit_sem); + return 0; } -- GitLab From dfb3cf00e402686f671db697adbd8b9f4c219268 Mon Sep 17 00:00:00 2001 From: Swen Schillig Date: Mon, 13 Jul 2009 15:06:02 +0200 Subject: [PATCH 0578/1342] [SCSI] zfcp: Fix invalid command order We should not modify the port status after triggering an ERP action for the port. It is not guaranteed which status is finally active when the ERP action is performed. This can lead to situations which are unwanted and hard to debug in case of a failure. Signed-off-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_fsf.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c index c57658f3d34..bbb7ef0b052 100644 --- a/drivers/s390/scsi/zfcp_fsf.c +++ b/drivers/s390/scsi/zfcp_fsf.c @@ -1731,15 +1731,16 @@ static void zfcp_fsf_close_physical_port_handler(struct zfcp_fsf_req *req) zfcp_fsf_access_denied_port(req, port); break; case FSF_PORT_BOXED: - zfcp_erp_port_boxed(port, "fscpph2", req); - req->status |= ZFCP_STATUS_FSFREQ_ERROR | - ZFCP_STATUS_FSFREQ_RETRY; /* can't use generic zfcp_erp_modify_port_status because * ZFCP_STATUS_COMMON_OPEN must not be reset for the port */ atomic_clear_mask(ZFCP_STATUS_PORT_PHYS_OPEN, &port->status); list_for_each_entry(unit, &port->unit_list_head, list) atomic_clear_mask(ZFCP_STATUS_COMMON_OPEN, &unit->status); + zfcp_erp_port_boxed(port, "fscpph2", req); + req->status |= ZFCP_STATUS_FSFREQ_ERROR | + ZFCP_STATUS_FSFREQ_RETRY; + break; case FSF_ADAPTER_STATUS_AVAILABLE: switch (header->fsf_status_qual.word[0]) { -- GitLab From acf7b86150701de105aa8307b4b3f9dc533c45bb Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:03 +0200 Subject: [PATCH 0579/1342] [SCSI] zfcp: Acquire qdio_stat_lock when reading the queue utilization req_q_util is not atomic, so the qdio_stat_lock must be held when reading this variable. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_sysfs.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/drivers/s390/scsi/zfcp_sysfs.c b/drivers/s390/scsi/zfcp_sysfs.c index 3e51e64d110..0fe5cce818c 100644 --- a/drivers/s390/scsi/zfcp_sysfs.c +++ b/drivers/s390/scsi/zfcp_sysfs.c @@ -494,9 +494,14 @@ static ssize_t zfcp_sysfs_adapter_q_full_show(struct device *dev, struct Scsi_Host *scsi_host = class_to_shost(dev); struct zfcp_adapter *adapter = (struct zfcp_adapter *) scsi_host->hostdata[0]; + u64 util; + + spin_lock_bh(&adapter->qdio_stat_lock); + util = adapter->req_q_util; + spin_unlock_bh(&adapter->qdio_stat_lock); return sprintf(buf, "%d %llu\n", atomic_read(&adapter->qdio_outb_full), - (unsigned long long)adapter->req_q_util); + (unsigned long long)util); } static DEVICE_ATTR(queue_full, S_IRUGO, zfcp_sysfs_adapter_q_full_show, NULL); -- GitLab From 1e9b16430ff4fd09408a74342d6b8338228e2f70 Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:04 +0200 Subject: [PATCH 0580/1342] [SCSI] zfcp: Return -ENOMEM for allocation failures in zfcp_fsf When a fsf_req or a qtcb cannot be allocated return -ENOMEM instead of -EIO. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_fsf.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c index bbb7ef0b052..c4eb62b32a3 100644 --- a/drivers/s390/scsi/zfcp_fsf.c +++ b/drivers/s390/scsi/zfcp_fsf.c @@ -722,7 +722,7 @@ static struct zfcp_fsf_req *zfcp_fsf_req_create(struct zfcp_adapter *adapter, req = zfcp_fsf_alloc_qtcb(pool); if (unlikely(!req)) - return ERR_PTR(-EIO); + return ERR_PTR(-ENOMEM); if (adapter->req_no == 0) adapter->req_no++; -- GitLab From 688a1820bde27749f22b18b94ef1c9bc179b1b29 Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:05 +0200 Subject: [PATCH 0581/1342] [SCSI] zfcp: Use correct flags for zfcp_erp_notify zfcp_erp_notify uses the ZFCP_ERP_STATUS_* flags, so it is ZFCP_STATUS_ERP_LOWMEM instead of ZFCP_ERP_NOMEM. Signalling ZFCP_ERP_FAILED is not necessary, the missing d_id will show that the nameserver did not return the d_id. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_erp.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/s390/scsi/zfcp_erp.c b/drivers/s390/scsi/zfcp_erp.c index 8030e25152f..e7d7ef55e37 100644 --- a/drivers/s390/scsi/zfcp_erp.c +++ b/drivers/s390/scsi/zfcp_erp.c @@ -854,10 +854,10 @@ void zfcp_erp_port_strategy_open_lookup(struct work_struct *work) retval = zfcp_fc_ns_gid_pn(&port->erp_action); if (retval == -ENOMEM) - zfcp_erp_notify(&port->erp_action, ZFCP_ERP_NOMEM); + zfcp_erp_notify(&port->erp_action, ZFCP_STATUS_ERP_LOWMEM); port->erp_action.step = ZFCP_ERP_STEP_NAMESERVER_LOOKUP; if (retval) - zfcp_erp_notify(&port->erp_action, ZFCP_ERP_FAILED); + zfcp_erp_notify(&port->erp_action, 0); zfcp_port_put(port); } -- GitLab From 426f6059b0eb66cec139f4b9066168ab72b85774 Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:06 +0200 Subject: [PATCH 0582/1342] [SCSI] zfcp: Use unchained mode for small ct and els requests The ELS ADISC and the GID_PN requests sent from zfcp fit into unchained FSF requests. Change the FSF allocation logic to use unchained requests whenever possible where everything fits in one SBAL. This avoids acquiring more SBALs than necessary, especially during zfcp recovery when things might be stalled. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_fsf.c | 33 +++++++++++++++++++++++++-------- 1 file changed, 25 insertions(+), 8 deletions(-) diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c index c4eb62b32a3..bec912547fb 100644 --- a/drivers/s390/scsi/zfcp_fsf.c +++ b/drivers/s390/scsi/zfcp_fsf.c @@ -1010,6 +1010,23 @@ skip_fsfstatus: send_ct->handler(send_ct->handler_data); } +static void zfcp_fsf_setup_ct_els_unchained(struct qdio_buffer_element *sbale, + struct scatterlist *sg_req, + struct scatterlist *sg_resp) +{ + sbale[0].flags |= SBAL_FLAGS0_TYPE_WRITE_READ; + sbale[2].addr = sg_virt(sg_req); + sbale[2].length = sg_req->length; + sbale[3].addr = sg_virt(sg_resp); + sbale[3].length = sg_resp->length; + sbale[3].flags |= SBAL_FLAGS_LAST_ENTRY; +} + +static int zfcp_fsf_one_sbal(struct scatterlist *sg) +{ + return sg_is_last(sg) && sg->length <= PAGE_SIZE; +} + static int zfcp_fsf_setup_ct_els_sbals(struct zfcp_fsf_req *req, struct scatterlist *sg_req, struct scatterlist *sg_resp, @@ -1020,16 +1037,16 @@ static int zfcp_fsf_setup_ct_els_sbals(struct zfcp_fsf_req *req, int bytes; if (!(feat & FSF_FEATURE_ELS_CT_CHAINED_SBALS)) { - if (sg_req->length > PAGE_SIZE || sg_resp->length > PAGE_SIZE || - !sg_is_last(sg_req) || !sg_is_last(sg_resp)) + if (!zfcp_fsf_one_sbal(sg_req) || !zfcp_fsf_one_sbal(sg_resp)) return -EOPNOTSUPP; - sbale[0].flags |= SBAL_FLAGS0_TYPE_WRITE_READ; - sbale[2].addr = sg_virt(sg_req); - sbale[2].length = sg_req->length; - sbale[3].addr = sg_virt(sg_resp); - sbale[3].length = sg_resp->length; - sbale[3].flags |= SBAL_FLAGS_LAST_ENTRY; + zfcp_fsf_setup_ct_els_unchained(sbale, sg_req, sg_resp); + return 0; + } + + /* use single, unchained SBAL if it can hold the request */ + if (zfcp_fsf_one_sbal(sg_req) && zfcp_fsf_one_sbal(sg_resp)) { + zfcp_fsf_setup_ct_els_unchained(sbale, sg_req, sg_resp); return 0; } -- GitLab From 9072df4dc6e8fd569d583815edb0198af4b688b8 Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:07 +0200 Subject: [PATCH 0583/1342] [SCSI] zfcp: Use -EIO for SBAL allocation failures -ENOMEM is for memory allocation problems, -EIO for queue/SBAL allocation problems. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_fsf.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c index bec912547fb..0c24695a53c 100644 --- a/drivers/s390/scsi/zfcp_fsf.c +++ b/drivers/s390/scsi/zfcp_fsf.c @@ -1053,14 +1053,14 @@ static int zfcp_fsf_setup_ct_els_sbals(struct zfcp_fsf_req *req, bytes = zfcp_qdio_sbals_from_sg(req, SBAL_FLAGS0_TYPE_WRITE_READ, sg_req, max_sbals); if (bytes <= 0) - return -ENOMEM; + return -EIO; req->qtcb->bottom.support.req_buf_length = bytes; req->sbale_curr = ZFCP_LAST_SBALE_PER_SBAL; bytes = zfcp_qdio_sbals_from_sg(req, SBAL_FLAGS0_TYPE_WRITE_READ, sg_resp, max_sbals); if (bytes <= 0) - return -ENOMEM; + return -EIO; req->qtcb->bottom.support.resp_buf_length = bytes; return 0; @@ -2559,7 +2559,6 @@ struct zfcp_fsf_req *zfcp_fsf_control_file(struct zfcp_adapter *adapter, bytes = zfcp_qdio_sbals_from_sg(req, direction, fsf_cfdc->sg, FSF_MAX_SBALS_PER_REQ); if (bytes != ZFCP_CFDC_MAX_SIZE) { - retval = -ENOMEM; zfcp_fsf_req_free(req); goto out; } -- GitLab From ddb3e0c111fed0a8bf74884dc918274acec2b618 Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:08 +0200 Subject: [PATCH 0584/1342] [SCSI] zfcp: Fix logic for physical port close After closing the port, we want it to be "not open" to consider the action to be successful. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_erp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/s390/scsi/zfcp_erp.c b/drivers/s390/scsi/zfcp_erp.c index e7d7ef55e37..0a7c6aef532 100644 --- a/drivers/s390/scsi/zfcp_erp.c +++ b/drivers/s390/scsi/zfcp_erp.c @@ -801,7 +801,7 @@ static int zfcp_erp_port_forced_strategy(struct zfcp_erp_action *erp_action) return ZFCP_ERP_FAILED; case ZFCP_ERP_STEP_PHYS_PORT_CLOSING: - if (status & ZFCP_STATUS_PORT_PHYS_OPEN) + if (!(status & ZFCP_STATUS_PORT_PHYS_OPEN)) return ZFCP_ERP_SUCCEEDED; } return ZFCP_ERP_FAILED; -- GitLab From 85600f7f8370fe5b4be0debd8b401de7986b52ae Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:09 +0200 Subject: [PATCH 0585/1342] [SCSI] zfcp: Fix erp escalation procedure If an action fails, retry it until the erp count exceeds the threshold. If there is something fundamentally wrong, the FSF layer will trigger a more appropriate action depending on the FSF status codes. The followup for successful actions is a different followup than retrying failed actions, so split the code two functions to make this clear. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_erp.c | 50 +++++++++++++++++------------------- 1 file changed, 24 insertions(+), 26 deletions(-) diff --git a/drivers/s390/scsi/zfcp_erp.c b/drivers/s390/scsi/zfcp_erp.c index 0a7c6aef532..b5562f95265 100644 --- a/drivers/s390/scsi/zfcp_erp.c +++ b/drivers/s390/scsi/zfcp_erp.c @@ -553,40 +553,35 @@ static void _zfcp_erp_unit_reopen_all(struct zfcp_port *port, int clear, _zfcp_erp_unit_reopen(unit, clear, id, ref); } -static void zfcp_erp_strategy_followup_actions(struct zfcp_erp_action *act) +static void zfcp_erp_strategy_followup_failed(struct zfcp_erp_action *act) { - struct zfcp_adapter *adapter = act->adapter; - struct zfcp_port *port = act->port; - struct zfcp_unit *unit = act->unit; - u32 status = act->status; - - /* initiate follow-up actions depending on success of finished action */ switch (act->action) { - case ZFCP_ERP_ACTION_REOPEN_ADAPTER: - if (status == ZFCP_ERP_SUCCEEDED) - _zfcp_erp_port_reopen_all(adapter, 0, "ersfa_1", NULL); - else - _zfcp_erp_adapter_reopen(adapter, 0, "ersfa_2", NULL); + _zfcp_erp_adapter_reopen(act->adapter, 0, "ersff_1", NULL); break; - case ZFCP_ERP_ACTION_REOPEN_PORT_FORCED: - if (status == ZFCP_ERP_SUCCEEDED) - _zfcp_erp_port_reopen(port, 0, "ersfa_3", NULL); - else - _zfcp_erp_adapter_reopen(adapter, 0, "ersfa_4", NULL); + _zfcp_erp_port_forced_reopen(act->port, 0, "ersff_2", NULL); break; - case ZFCP_ERP_ACTION_REOPEN_PORT: - if (status == ZFCP_ERP_SUCCEEDED) - _zfcp_erp_unit_reopen_all(port, 0, "ersfa_5", NULL); - else - _zfcp_erp_port_forced_reopen(port, 0, "ersfa_6", NULL); + _zfcp_erp_port_reopen(act->port, 0, "ersff_3", NULL); break; - case ZFCP_ERP_ACTION_REOPEN_UNIT: - if (status != ZFCP_ERP_SUCCEEDED) - _zfcp_erp_port_reopen(unit->port, 0, "ersfa_7", NULL); + _zfcp_erp_unit_reopen(act->unit, 0, "ersff_4", NULL); + break; + } +} + +static void zfcp_erp_strategy_followup_success(struct zfcp_erp_action *act) +{ + switch (act->action) { + case ZFCP_ERP_ACTION_REOPEN_ADAPTER: + _zfcp_erp_port_reopen_all(act->adapter, 0, "ersfs_1", NULL); + break; + case ZFCP_ERP_ACTION_REOPEN_PORT_FORCED: + _zfcp_erp_port_reopen(act->port, 0, "ersfs_2", NULL); + break; + case ZFCP_ERP_ACTION_REOPEN_PORT: + _zfcp_erp_unit_reopen_all(act->port, 0, "ersfs_3", NULL); break; } } @@ -1289,7 +1284,10 @@ static int zfcp_erp_strategy(struct zfcp_erp_action *erp_action) retval = zfcp_erp_strategy_statechange(erp_action, retval); if (retval == ZFCP_ERP_EXIT) goto unlock; - zfcp_erp_strategy_followup_actions(erp_action); + if (retval == ZFCP_ERP_SUCCEEDED) + zfcp_erp_strategy_followup_success(erp_action); + if (retval == ZFCP_ERP_FAILED) + zfcp_erp_strategy_followup_failed(erp_action); unlock: write_unlock(&adapter->erp_lock); -- GitLab From cbf1ed0264da104573458aedc220ebfcd02567f6 Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:10 +0200 Subject: [PATCH 0586/1342] [SCSI] zfcp: Recover from stalled outbound queue Depending on interruptions on some storage systems, the complete channel can stall which looks like an outbound queue stall to Linux. When trying to acquire a free SBAL for a non-SCSI command, zfcp waits for 5 seconds for a free slot to appear. This is the right place to detect a queue stall: If the wait times out, we assume a stalled queue and try to recover this. The overall strategy should be to trigger the erp from specific events, and not try an overall escalation from one failed port to a full-blown queue recovery. If we manage to send a command, the status codes for this command or a timeout will trigger the right follow-on actions. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_fsf.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c index 0c24695a53c..b7e48844056 100644 --- a/drivers/s390/scsi/zfcp_fsf.c +++ b/drivers/s390/scsi/zfcp_fsf.c @@ -670,8 +670,11 @@ static int zfcp_fsf_req_sbal_get(struct zfcp_adapter *adapter) zfcp_fsf_sbal_check(adapter), 5 * HZ); if (ret > 0) return 0; - if (!ret) + if (!ret) { atomic_inc(&adapter->qdio_outb_full); + /* assume hanging outbound queue, try queue recovery */ + zfcp_erp_adapter_reopen(adapter, 0, "fsrsg_1", NULL); + } spin_lock_bh(&adapter->req_q_lock); return -EIO; -- GitLab From 379d6bf6573ee6541a38bbe9140c1f0b94e3feae Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:11 +0200 Subject: [PATCH 0587/1342] [SCSI] zfcp: Add port only once to FC transport class When calling fc_remote_port_add make sure to not call it again before fc_remote_port_delete has been called. In other words, ensure to create a new fc_rport, then delete it, then create a new one again. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_scsi.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/drivers/s390/scsi/zfcp_scsi.c b/drivers/s390/scsi/zfcp_scsi.c index 967ede73f4c..ba32709921a 100644 --- a/drivers/s390/scsi/zfcp_scsi.c +++ b/drivers/s390/scsi/zfcp_scsi.c @@ -534,6 +534,9 @@ static void zfcp_scsi_rport_register(struct zfcp_port *port) struct fc_rport_identifiers ids; struct fc_rport *rport; + if (port->rport) + return; + ids.node_name = port->wwnn; ids.port_name = port->wwpn; ids.port_id = port->d_id; @@ -557,8 +560,10 @@ static void zfcp_scsi_rport_block(struct zfcp_port *port) { struct fc_rport *rport = port->rport; - if (rport) + if (rport) { fc_remote_port_delete(rport); + port->rport = NULL; + } } void zfcp_scsi_schedule_rport_register(struct zfcp_port *port) -- GitLab From 17a093ef018481ee1760da19568bad3c11da395d Mon Sep 17 00:00:00 2001 From: Swen Schillig Date: Mon, 13 Jul 2009 15:06:12 +0200 Subject: [PATCH 0588/1342] [SCSI] zfcp: avoid double notify in lowmem scenario In a LOWMEM condition an ERP notification would have been sent twice causing an unpredictable behaviour of the ERP. Signed-off-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_erp.c | 14 ++++++++++---- 1 file changed, 10 insertions(+), 4 deletions(-) diff --git a/drivers/s390/scsi/zfcp_erp.c b/drivers/s390/scsi/zfcp_erp.c index b5562f95265..c75d6f35cb5 100644 --- a/drivers/s390/scsi/zfcp_erp.c +++ b/drivers/s390/scsi/zfcp_erp.c @@ -848,11 +848,17 @@ void zfcp_erp_port_strategy_open_lookup(struct work_struct *work) gid_pn_work); retval = zfcp_fc_ns_gid_pn(&port->erp_action); - if (retval == -ENOMEM) + if (!retval) { + port->erp_action.step = ZFCP_ERP_STEP_NAMESERVER_LOOKUP; + goto out; + } + if (retval == -ENOMEM) { zfcp_erp_notify(&port->erp_action, ZFCP_STATUS_ERP_LOWMEM); - port->erp_action.step = ZFCP_ERP_STEP_NAMESERVER_LOOKUP; - if (retval) - zfcp_erp_notify(&port->erp_action, 0); + goto out; + } + /* all other error condtions */ + zfcp_erp_notify(&port->erp_action, 0); +out: zfcp_port_put(port); } -- GitLab From 27f492ccec94b6acd8440c83bfe0515ce4db0af0 Mon Sep 17 00:00:00 2001 From: Swen Schillig Date: Mon, 13 Jul 2009 15:06:13 +0200 Subject: [PATCH 0589/1342] [SCSI] zfcp: Fix wka port processing Under certain conditions it is possible that a WKA port ist not opened within the expected timeframe of half a second. In this situation the WKA port remains in the state OPENING preventing any succeding request to open the port. This led to unrecoverable remote ports. Fixing this by always setting an appropriate WKA port status before leaving the function and removing the timeout value here since it's not needed here because the general timeout processing would deal with it if required. Signed-off-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_fc.c | 8 +++----- drivers/s390/scsi/zfcp_fsf.c | 4 ++-- 2 files changed, 5 insertions(+), 7 deletions(-) diff --git a/drivers/s390/scsi/zfcp_fc.c b/drivers/s390/scsi/zfcp_fc.c index 2f0705d76b7..47daebfa7e5 100644 --- a/drivers/s390/scsi/zfcp_fc.c +++ b/drivers/s390/scsi/zfcp_fc.c @@ -79,11 +79,9 @@ static int zfcp_wka_port_get(struct zfcp_wka_port *wka_port) mutex_unlock(&wka_port->mutex); - wait_event_timeout( - wka_port->completion_wq, - wka_port->status == ZFCP_WKA_PORT_ONLINE || - wka_port->status == ZFCP_WKA_PORT_OFFLINE, - HZ >> 1); + wait_event(wka_port->completion_wq, + wka_port->status == ZFCP_WKA_PORT_ONLINE || + wka_port->status == ZFCP_WKA_PORT_OFFLINE); if (wka_port->status == ZFCP_WKA_PORT_ONLINE) { atomic_inc(&wka_port->refcount); diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c index b7e48844056..47795fbf081 100644 --- a/drivers/s390/scsi/zfcp_fsf.c +++ b/drivers/s390/scsi/zfcp_fsf.c @@ -1627,10 +1627,10 @@ static void zfcp_fsf_open_wka_port_handler(struct zfcp_fsf_req *req) case FSF_ACCESS_DENIED: wka_port->status = ZFCP_WKA_PORT_OFFLINE; break; - case FSF_PORT_ALREADY_OPEN: - break; case FSF_GOOD: wka_port->handle = header->port_handle; + /* fall through */ + case FSF_PORT_ALREADY_OPEN: wka_port->status = ZFCP_WKA_PORT_ONLINE; } out: -- GitLab From a11a52be115889a5d1f738ed2e154807bceed4ee Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:14 +0200 Subject: [PATCH 0590/1342] [SCSI] zfcp: Fix tracing of request id for abort requests The trace record for SCSI abort requests has a field for the request id of the request to be aborted. Put the real request id instead of zero. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_scsi.c | 18 ++++++++++-------- 1 file changed, 10 insertions(+), 8 deletions(-) diff --git a/drivers/s390/scsi/zfcp_scsi.c b/drivers/s390/scsi/zfcp_scsi.c index ba32709921a..6925a178468 100644 --- a/drivers/s390/scsi/zfcp_scsi.c +++ b/drivers/s390/scsi/zfcp_scsi.c @@ -167,20 +167,21 @@ static int zfcp_scsi_eh_abort_handler(struct scsi_cmnd *scpnt) struct zfcp_unit *unit = scpnt->device->hostdata; struct zfcp_fsf_req *old_req, *abrt_req; unsigned long flags; - unsigned long old_req_id = (unsigned long) scpnt->host_scribble; + unsigned long old_reqid = (unsigned long) scpnt->host_scribble; int retval = SUCCESS; int retry = 3; + char *dbf_tag; /* avoid race condition between late normal completion and abort */ write_lock_irqsave(&adapter->abort_lock, flags); spin_lock(&adapter->req_list_lock); - old_req = zfcp_reqlist_find(adapter, old_req_id); + old_req = zfcp_reqlist_find(adapter, old_reqid); spin_unlock(&adapter->req_list_lock); if (!old_req) { write_unlock_irqrestore(&adapter->abort_lock, flags); zfcp_scsi_dbf_event_abort("lte1", adapter, scpnt, NULL, - old_req_id); + old_reqid); return FAILED; /* completion could be in progress */ } old_req->data = NULL; @@ -189,7 +190,7 @@ static int zfcp_scsi_eh_abort_handler(struct scsi_cmnd *scpnt) write_unlock_irqrestore(&adapter->abort_lock, flags); while (retry--) { - abrt_req = zfcp_fsf_abort_fcp_command(old_req_id, unit); + abrt_req = zfcp_fsf_abort_fcp_command(old_reqid, unit); if (abrt_req) break; @@ -197,7 +198,7 @@ static int zfcp_scsi_eh_abort_handler(struct scsi_cmnd *scpnt) if (!(atomic_read(&adapter->status) & ZFCP_STATUS_COMMON_RUNNING)) { zfcp_scsi_dbf_event_abort("nres", adapter, scpnt, NULL, - old_req_id); + old_reqid); return SUCCESS; } } @@ -208,13 +209,14 @@ static int zfcp_scsi_eh_abort_handler(struct scsi_cmnd *scpnt) abrt_req->status & ZFCP_STATUS_FSFREQ_COMPLETED); if (abrt_req->status & ZFCP_STATUS_FSFREQ_ABORTSUCCEEDED) - zfcp_scsi_dbf_event_abort("okay", adapter, scpnt, abrt_req, 0); + dbf_tag = "okay"; else if (abrt_req->status & ZFCP_STATUS_FSFREQ_ABORTNOTNEEDED) - zfcp_scsi_dbf_event_abort("lte2", adapter, scpnt, abrt_req, 0); + dbf_tag = "lte2"; else { - zfcp_scsi_dbf_event_abort("fail", adapter, scpnt, abrt_req, 0); + dbf_tag = "fail"; retval = FAILED; } + zfcp_scsi_dbf_event_abort(dbf_tag, adapter, scpnt, abrt_req, old_reqid); zfcp_fsf_req_free(abrt_req); return retval; } -- GitLab From 6187c242089d334102be76427a5a020240e6c19a Mon Sep 17 00:00:00 2001 From: Mike Christie Date: Wed, 15 Jul 2009 15:02:57 -0500 Subject: [PATCH 0591/1342] [SCSI] libiscsi: disable bh in and abort handler. The session lock can be held in the scsi eh thread or the completion paths run from the net softirq. This disables bhs in iscsi_eh_abort when taking the session lock. Signed-off-by: Mike Christie Signed-off-by: James Bottomley --- drivers/scsi/libiscsi.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/scsi/libiscsi.c b/drivers/scsi/libiscsi.c index 716cc344c5d..a751f6230c2 100644 --- a/drivers/scsi/libiscsi.c +++ b/drivers/scsi/libiscsi.c @@ -1974,10 +1974,10 @@ int iscsi_eh_abort(struct scsi_cmnd *sc) * good and have never sent us a successful tmf response * then sent more data for the cmd. */ - spin_lock(&session->lock); + spin_lock_bh(&session->lock); fail_scsi_task(task, DID_ABORT); conn->tmf_state = TMF_INITIAL; - spin_unlock(&session->lock); + spin_unlock_bh(&session->lock); iscsi_start_tx(conn); goto success_unlocked; case TMF_TIMEDOUT: -- GitLab From 94bced3c1b371014cbd187f2df5539b13a0e3b90 Mon Sep 17 00:00:00 2001 From: Karen Higgins Date: Wed, 15 Jul 2009 15:02:58 -0500 Subject: [PATCH 0592/1342] [SCSI] qla4xxx: Correct Extended Sense Data Errors Fixed sense data errors occurring above the first 32 bytes, as required by some third party applications. Sense data in the first 32 bytes has always been correct. Patch updated to use srb data variables instead of scsi command scratchpad data area, as scratchpad area is already used. Also, corrected debug print alignment bug in dump_buffer routine. Changed KERN_DEBUG to KERN_INFO in printk statements in this routine. Changed version number to 5.01.00-k9 Signed-off-by: Karen Higgins [michaelc: fixed checkpath.pl errors] Signed-off-by: Mike Christie Signed-off-by: James Bottomley --- drivers/scsi/qla4xxx/ql4_dbg.c | 15 ++- drivers/scsi/qla4xxx/ql4_def.h | 7 ++ drivers/scsi/qla4xxx/ql4_fw.h | 7 ++ drivers/scsi/qla4xxx/ql4_isr.c | 145 ++++++++++++++++++++--------- drivers/scsi/qla4xxx/ql4_version.h | 2 +- 5 files changed, 122 insertions(+), 54 deletions(-) diff --git a/drivers/scsi/qla4xxx/ql4_dbg.c b/drivers/scsi/qla4xxx/ql4_dbg.c index fcc184cd066..cbceb0ebabf 100644 --- a/drivers/scsi/qla4xxx/ql4_dbg.c +++ b/drivers/scsi/qla4xxx/ql4_dbg.c @@ -15,19 +15,18 @@ void qla4xxx_dump_buffer(void *b, uint32_t size) uint32_t cnt; uint8_t *c = b; - printk(" 0 1 2 3 4 5 6 7 8 9 Ah Bh Ch Dh Eh " + printk(" 0 1 2 3 4 5 6 7 8 9 Ah Bh Ch Dh Eh " "Fh\n"); printk("------------------------------------------------------------" "--\n"); - for (cnt = 0; cnt < size; cnt++, c++) { - printk(KERN_DEBUG "%02x", *c); - if (!(cnt % 16)) - printk(KERN_DEBUG "\n"); + for (cnt = 0; cnt < size; c++) { + printk(KERN_INFO "%02x", *c); + if (!(++cnt % 16)) + printk(KERN_INFO "\n"); else - printk(KERN_DEBUG " "); + printk(KERN_INFO " "); } - if (cnt % 16) - printk(KERN_DEBUG "\n"); + printk(KERN_INFO "\n"); } diff --git a/drivers/scsi/qla4xxx/ql4_def.h b/drivers/scsi/qla4xxx/ql4_def.h index b586f27c3bd..963e8553d21 100644 --- a/drivers/scsi/qla4xxx/ql4_def.h +++ b/drivers/scsi/qla4xxx/ql4_def.h @@ -184,6 +184,11 @@ struct srb { uint16_t cc_stat; u_long r_start; /* Time we recieve a cmd from OS */ u_long u_start; /* Time when we handed the cmd to F/W */ + + /* Used for extended sense / status continuation */ + uint8_t *req_sense_ptr; + uint16_t req_sense_len; + uint16_t reserved2; }; /* @@ -436,6 +441,8 @@ struct scsi_qla_host { /* Map ddb_list entry by FW ddb index */ struct ddb_entry *fw_ddb_index_map[MAX_DDB_ENTRIES]; + /* Saved srb for status continuation entry processing */ + struct srb *status_srb; }; static inline int is_qla4010(struct scsi_qla_host *ha) diff --git a/drivers/scsi/qla4xxx/ql4_fw.h b/drivers/scsi/qla4xxx/ql4_fw.h index 1b667a70cff..9cd7a608df3 100644 --- a/drivers/scsi/qla4xxx/ql4_fw.h +++ b/drivers/scsi/qla4xxx/ql4_fw.h @@ -572,6 +572,7 @@ struct conn_event_log_entry { *************************************************************************/ #define IOCB_MAX_CDB_LEN 16 /* Bytes in a CBD */ #define IOCB_MAX_SENSEDATA_LEN 32 /* Bytes of sense data */ +#define IOCB_MAX_EXT_SENSEDATA_LEN 60 /* Bytes of extended sense data */ /* IOCB header structure */ struct qla4_header { @@ -733,6 +734,12 @@ struct status_entry { }; +/* Status Continuation entry */ +struct status_cont_entry { + struct qla4_header hdr; /* 00-03 */ + uint8_t ext_sense_data[IOCB_MAX_EXT_SENSEDATA_LEN]; /* 04-63 */ +}; + struct passthru0 { struct qla4_header hdr; /* 00-03 */ uint32_t handle; /* 04-07 */ diff --git a/drivers/scsi/qla4xxx/ql4_isr.c b/drivers/scsi/qla4xxx/ql4_isr.c index 799120fcb9b..8025ee16588 100644 --- a/drivers/scsi/qla4xxx/ql4_isr.c +++ b/drivers/scsi/qla4xxx/ql4_isr.c @@ -10,6 +10,98 @@ #include "ql4_dbg.h" #include "ql4_inline.h" +/** + * qla4xxx_copy_sense - copy sense data into cmd sense buffer + * @ha: Pointer to host adapter structure. + * @sts_entry: Pointer to status entry structure. + * @srb: Pointer to srb structure. + **/ +static void qla4xxx_copy_sense(struct scsi_qla_host *ha, + struct status_entry *sts_entry, + struct srb *srb) +{ + struct scsi_cmnd *cmd = srb->cmd; + uint16_t sense_len; + + memset(cmd->sense_buffer, 0, SCSI_SENSE_BUFFERSIZE); + sense_len = le16_to_cpu(sts_entry->senseDataByteCnt); + if (sense_len == 0) + return; + + /* Save total available sense length, + * not to exceed cmd's sense buffer size */ + sense_len = min_t(uint16_t, sense_len, SCSI_SENSE_BUFFERSIZE); + srb->req_sense_ptr = cmd->sense_buffer; + srb->req_sense_len = sense_len; + + /* Copy sense from sts_entry pkt */ + sense_len = min_t(uint16_t, sense_len, IOCB_MAX_SENSEDATA_LEN); + memcpy(cmd->sense_buffer, sts_entry->senseData, sense_len); + + DEBUG2(printk(KERN_INFO "scsi%ld:%d:%d:%d: %s: sense key = %x, " + "ASL= %02x, ASC/ASCQ = %02x/%02x\n", ha->host_no, + cmd->device->channel, cmd->device->id, + cmd->device->lun, __func__, + sts_entry->senseData[2] & 0x0f, + sts_entry->senseData[7], + sts_entry->senseData[12], + sts_entry->senseData[13])); + + DEBUG5(qla4xxx_dump_buffer(cmd->sense_buffer, sense_len)); + srb->flags |= SRB_GOT_SENSE; + + /* Update srb, in case a sts_cont pkt follows */ + srb->req_sense_ptr += sense_len; + srb->req_sense_len -= sense_len; + if (srb->req_sense_len != 0) + ha->status_srb = srb; + else + ha->status_srb = NULL; +} + +/** + * qla4xxx_status_cont_entry - Process a Status Continuations entry. + * @ha: SCSI driver HA context + * @sts_cont: Entry pointer + * + * Extended sense data. + */ +static void +qla4xxx_status_cont_entry(struct scsi_qla_host *ha, + struct status_cont_entry *sts_cont) +{ + struct srb *srb = ha->status_srb; + struct scsi_cmnd *cmd; + uint8_t sense_len; + + if (srb == NULL) + return; + + cmd = srb->cmd; + if (cmd == NULL) { + DEBUG2(printk(KERN_INFO "scsi%ld: %s: Cmd already returned " + "back to OS srb=%p srb->state:%d\n", ha->host_no, + __func__, srb, srb->state)); + ha->status_srb = NULL; + return; + } + + /* Copy sense data. */ + sense_len = min_t(uint16_t, srb->req_sense_len, + IOCB_MAX_EXT_SENSEDATA_LEN); + memcpy(srb->req_sense_ptr, sts_cont->ext_sense_data, sense_len); + DEBUG5(qla4xxx_dump_buffer(srb->req_sense_ptr, sense_len)); + + srb->req_sense_ptr += sense_len; + srb->req_sense_len -= sense_len; + + /* Place command on done queue. */ + if (srb->req_sense_len == 0) { + qla4xxx_srb_compl(ha, srb); + ha->status_srb = NULL; + } +} + /** * qla4xxx_status_entry - processes status IOCBs * @ha: Pointer to host adapter structure. @@ -23,7 +115,6 @@ static void qla4xxx_status_entry(struct scsi_qla_host *ha, struct srb *srb; struct ddb_entry *ddb_entry; uint32_t residual; - uint16_t sensebytecnt; srb = qla4xxx_del_from_active_array(ha, le32_to_cpu(sts_entry->handle)); if (!srb) { @@ -92,24 +183,7 @@ static void qla4xxx_status_entry(struct scsi_qla_host *ha, break; /* Copy Sense Data into sense buffer. */ - memset(cmd->sense_buffer, 0, SCSI_SENSE_BUFFERSIZE); - - sensebytecnt = le16_to_cpu(sts_entry->senseDataByteCnt); - if (sensebytecnt == 0) - break; - - memcpy(cmd->sense_buffer, sts_entry->senseData, - min_t(uint16_t, sensebytecnt, SCSI_SENSE_BUFFERSIZE)); - - DEBUG2(printk("scsi%ld:%d:%d:%d: %s: sense key = %x, " - "ASC/ASCQ = %02x/%02x\n", ha->host_no, - cmd->device->channel, cmd->device->id, - cmd->device->lun, __func__, - sts_entry->senseData[2] & 0x0f, - sts_entry->senseData[12], - sts_entry->senseData[13])); - - srb->flags |= SRB_GOT_SENSE; + qla4xxx_copy_sense(ha, sts_entry, srb); break; case SCS_INCOMPLETE: @@ -176,23 +250,7 @@ static void qla4xxx_status_entry(struct scsi_qla_host *ha, break; /* Copy Sense Data into sense buffer. */ - memset(cmd->sense_buffer, 0, SCSI_SENSE_BUFFERSIZE); - - sensebytecnt = - le16_to_cpu(sts_entry->senseDataByteCnt); - if (sensebytecnt == 0) - break; - - memcpy(cmd->sense_buffer, sts_entry->senseData, - min_t(uint16_t, sensebytecnt, SCSI_SENSE_BUFFERSIZE)); - - DEBUG2(printk("scsi%ld:%d:%d:%d: %s: sense key = %x, " - "ASC/ASCQ = %02x/%02x\n", ha->host_no, - cmd->device->channel, cmd->device->id, - cmd->device->lun, __func__, - sts_entry->senseData[2] & 0x0f, - sts_entry->senseData[12], - sts_entry->senseData[13])); + qla4xxx_copy_sense(ha, sts_entry, srb); } else { /* * If RISC reports underrun and target does not @@ -268,9 +326,10 @@ static void qla4xxx_status_entry(struct scsi_qla_host *ha, status_entry_exit: - /* complete the request */ + /* complete the request, if not waiting for status_continuation pkt */ srb->cc_stat = sts_entry->completionStatus; - qla4xxx_srb_compl(ha, srb); + if (ha->status_srb == NULL) + qla4xxx_srb_compl(ha, srb); } /** @@ -305,10 +364,7 @@ static void qla4xxx_process_response_queue(struct scsi_qla_host * ha) /* process entry */ switch (sts_entry->hdr.entryType) { case ET_STATUS: - /* - * Common status - Single completion posted in single - * IOSB. - */ + /* Common status */ qla4xxx_status_entry(ha, sts_entry); break; @@ -316,9 +372,8 @@ static void qla4xxx_process_response_queue(struct scsi_qla_host * ha) break; case ET_STATUS_CONTINUATION: - /* Just throw away the status continuation entries */ - DEBUG2(printk("scsi%ld: %s: Status Continuation entry " - "- ignoring\n", ha->host_no, __func__)); + qla4xxx_status_cont_entry(ha, + (struct status_cont_entry *) sts_entry); break; case ET_COMMAND: diff --git a/drivers/scsi/qla4xxx/ql4_version.h b/drivers/scsi/qla4xxx/ql4_version.h index ab984cb89ce..6980cb279c8 100644 --- a/drivers/scsi/qla4xxx/ql4_version.h +++ b/drivers/scsi/qla4xxx/ql4_version.h @@ -5,5 +5,5 @@ * See LICENSE.qla4xxx for copyright and licensing details. */ -#define QLA4XXX_DRIVER_VERSION "5.01.00-k8" +#define QLA4XXX_DRIVER_VERSION "5.01.00-k9" -- GitLab From 5c656af7e4edfe44c85034d6fa7002909f9c3c59 Mon Sep 17 00:00:00 2001 From: Mike Christie Date: Wed, 15 Jul 2009 15:02:59 -0500 Subject: [PATCH 0593/1342] [SCSI] qla4xxx: add timeout handler Recently dm-multipath began calling blk_abort_queue. This causes all the commands/request running on the path to have the timeout function called. If a path does go down, and the LLD returns DID_*, dm-multpiath will eventually get this error and begin to call the cmd timeout handler. qla4xxx currently does not set a timed out handler and so the default one could return BLK_EH_NOT_HANDLED and end up firing the scsi eh and stopping IO to all paths on the host when only one path is affected. For software and offload iscsi we have a timed out handler already. This patch adds a driver specific one to qla4xxx because there are some ddb->state and session->state and command completion races that are better handled in the LLD. This also handles the problem where if the session is down, we do not need the scsi eh to run until the transport code has tried to reconnect us. Signed-off-by: Mike Christie Signed-off-by: James Bottomley --- drivers/scsi/qla4xxx/ql4_os.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) diff --git a/drivers/scsi/qla4xxx/ql4_os.c b/drivers/scsi/qla4xxx/ql4_os.c index ec9da6ce848..6841883b361 100644 --- a/drivers/scsi/qla4xxx/ql4_os.c +++ b/drivers/scsi/qla4xxx/ql4_os.c @@ -66,6 +66,7 @@ static int qla4xxx_sess_get_param(struct iscsi_cls_session *sess, static int qla4xxx_host_get_param(struct Scsi_Host *shost, enum iscsi_host_param param, char *buf); static void qla4xxx_recovery_timedout(struct iscsi_cls_session *session); +static enum blk_eh_timer_return qla4xxx_eh_cmd_timed_out(struct scsi_cmnd *sc); /* * SCSI host template entry points @@ -89,6 +90,7 @@ static struct scsi_host_template qla4xxx_driver_template = { .eh_device_reset_handler = qla4xxx_eh_device_reset, .eh_target_reset_handler = qla4xxx_eh_target_reset, .eh_host_reset_handler = qla4xxx_eh_host_reset, + .eh_timed_out = qla4xxx_eh_cmd_timed_out, .slave_configure = qla4xxx_slave_configure, .slave_alloc = qla4xxx_slave_alloc, @@ -124,6 +126,21 @@ static struct iscsi_transport qla4xxx_iscsi_transport = { static struct scsi_transport_template *qla4xxx_scsi_transport; +static enum blk_eh_timer_return qla4xxx_eh_cmd_timed_out(struct scsi_cmnd *sc) +{ + struct iscsi_cls_session *session; + struct ddb_entry *ddb_entry; + + session = starget_to_session(scsi_target(sc->device)); + ddb_entry = session->dd_data; + + /* if we are not logged in then the LLD is going to clean up the cmd */ + if (atomic_read(&ddb_entry->state) != DDB_STATE_ONLINE) + return BLK_EH_RESET_TIMER; + else + return BLK_EH_NOT_HANDLED; +} + static void qla4xxx_recovery_timedout(struct iscsi_cls_session *session) { struct ddb_entry *ddb_entry = session->dd_data; -- GitLab From dca05c4c07c48da0509708d9e562578d269e90e5 Mon Sep 17 00:00:00 2001 From: Karen Higgins Date: Wed, 15 Jul 2009 15:03:00 -0500 Subject: [PATCH 0594/1342] [SCSI] qla4xxx: Fix Driver Fault Recovery Completion Fixed driver bug where adapter recovery did not complete if there were outstanding commands detected on that host adapter. Signed-off-by: Karen Higgins Signed-off-by: Mike Christie Signed-off-by: James Bottomley --- drivers/scsi/qla4xxx/ql4_os.c | 19 +++++++++---------- 1 file changed, 9 insertions(+), 10 deletions(-) diff --git a/drivers/scsi/qla4xxx/ql4_os.c b/drivers/scsi/qla4xxx/ql4_os.c index 6841883b361..e1cc0d21d89 100644 --- a/drivers/scsi/qla4xxx/ql4_os.c +++ b/drivers/scsi/qla4xxx/ql4_os.c @@ -921,18 +921,17 @@ static int qla4xxx_recover_adapter(struct scsi_qla_host *ha, /* Flush any pending ddb changed AENs */ qla4xxx_process_aen(ha, FLUSH_DDB_CHANGED_AENS); + qla4xxx_flush_active_srbs(ha); + /* Reset the firmware. If successful, function * returns with ISP interrupts enabled. */ - if (status == QLA_SUCCESS) { - DEBUG2(printk("scsi%ld: %s - Performing soft reset..\n", - ha->host_no, __func__)); - qla4xxx_flush_active_srbs(ha); - if (ql4xxx_lock_drvr_wait(ha) == QLA_SUCCESS) - status = qla4xxx_soft_reset(ha); - else - status = QLA_ERROR; - } + DEBUG2(printk("scsi%ld: %s - Performing soft reset..\n", + ha->host_no, __func__)); + if (ql4xxx_lock_drvr_wait(ha) == QLA_SUCCESS) + status = qla4xxx_soft_reset(ha); + else + status = QLA_ERROR; /* Flush any pending ddb changed AENs */ qla4xxx_process_aen(ha, FLUSH_DDB_CHANGED_AENS); @@ -1661,7 +1660,7 @@ static int qla4xxx_eh_host_reset(struct scsi_cmnd *cmd) ha = (struct scsi_qla_host *) cmd->device->host->hostdata; dev_info(&ha->pdev->dev, - "scsi(%ld:%d:%d:%d): ADAPTER RESET ISSUED.\n", ha->host_no, + "scsi(%ld:%d:%d:%d): HOST RESET ISSUED.\n", ha->host_no, cmd->device->channel, cmd->device->id, cmd->device->lun); if (qla4xxx_wait_for_hba_online(ha) != QLA_SUCCESS) { -- GitLab From 612f73488785829d4f34aad00bfe30b904c94c9e Mon Sep 17 00:00:00 2001 From: Karen Higgins Date: Wed, 15 Jul 2009 15:03:01 -0500 Subject: [PATCH 0595/1342] [SCSI] qla4xxx: Fix srb lookup in qla4xxx_eh_device_reset eh_device_reset may be called from scsi error handler or sg_reset, etc. When called from sg_reset, there will not be an associated srb. The driver should lookup the corresponding device handle given information from the supplied cmd structure and should not assume that there exists an srb. Signed-off-by: Karen Higgins Signed-off-by: Mike Christie Signed-off-by: James Bottomley --- drivers/scsi/qla4xxx/ql4_os.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/drivers/scsi/qla4xxx/ql4_os.c b/drivers/scsi/qla4xxx/ql4_os.c index e1cc0d21d89..40e3cafb3a9 100644 --- a/drivers/scsi/qla4xxx/ql4_os.c +++ b/drivers/scsi/qla4xxx/ql4_os.c @@ -1543,11 +1543,9 @@ static int qla4xxx_eh_device_reset(struct scsi_cmnd *cmd) { struct scsi_qla_host *ha = to_qla_host(cmd->device->host); struct ddb_entry *ddb_entry = cmd->device->hostdata; - struct srb *sp; int ret = FAILED, stat; - sp = (struct srb *) cmd->SCp.ptr; - if (!sp || !ddb_entry) + if (!ddb_entry) return ret; dev_info(&ha->pdev->dev, -- GitLab From 16ed55f9de6743ceece9bf528362cadff10f1c5c Mon Sep 17 00:00:00 2001 From: Karen Higgins Date: Wed, 15 Jul 2009 15:03:02 -0500 Subject: [PATCH 0596/1342] [SCSI] qla4xxx: Remove hiwat code so scsi eh does not get escalated when we can make progress Removed unnecessary hiwat code to free up the number available IOCBs. Eliminates unnecessary eh_ escalations due to inability to obtain IOCB pkt for marker. v2. - Remove define not used anymore and fix req_q_coun accounting. Signed-off-by: Karen Higgins [michaelc: ported patch from qlogic.com driver to upstream] Signed-off-by: Mike Christie Signed-off-by: James Bottomley --- drivers/scsi/qla4xxx/ql4_def.h | 2 - drivers/scsi/qla4xxx/ql4_iocb.c | 133 ++++++++++++++------------------ drivers/scsi/qla4xxx/ql4_mbx.c | 10 --- 3 files changed, 60 insertions(+), 85 deletions(-) diff --git a/drivers/scsi/qla4xxx/ql4_def.h b/drivers/scsi/qla4xxx/ql4_def.h index 963e8553d21..81b5f29254e 100644 --- a/drivers/scsi/qla4xxx/ql4_def.h +++ b/drivers/scsi/qla4xxx/ql4_def.h @@ -100,7 +100,6 @@ #define MAX_SRBS MAX_CMDS_TO_RISC #define MBOX_AEN_REG_COUNT 5 #define MAX_INIT_RETRIES 5 -#define IOCB_HIWAT_CUSHION 16 /* * Buffer sizes @@ -307,7 +306,6 @@ struct scsi_qla_host { uint32_t tot_ddbs; uint16_t iocb_cnt; - uint16_t iocb_hiwat; /* SRB cache. */ #define SRB_MIN_REQ 128 diff --git a/drivers/scsi/qla4xxx/ql4_iocb.c b/drivers/scsi/qla4xxx/ql4_iocb.c index 912a67494ad..e0c32159749 100644 --- a/drivers/scsi/qla4xxx/ql4_iocb.c +++ b/drivers/scsi/qla4xxx/ql4_iocb.c @@ -10,9 +10,42 @@ #include "ql4_dbg.h" #include "ql4_inline.h" - #include +static int +qla4xxx_space_in_req_ring(struct scsi_qla_host *ha, uint16_t req_cnt) +{ + uint16_t cnt; + + /* Calculate number of free request entries. */ + if ((req_cnt + 2) >= ha->req_q_count) { + cnt = (uint16_t) le32_to_cpu(ha->shadow_regs->req_q_out); + if (ha->request_in < cnt) + ha->req_q_count = cnt - ha->request_in; + else + ha->req_q_count = REQUEST_QUEUE_DEPTH - + (ha->request_in - cnt); + } + + /* Check if room for request in request ring. */ + if ((req_cnt + 2) < ha->req_q_count) + return 1; + else + return 0; +} + +static void qla4xxx_advance_req_ring_ptr(struct scsi_qla_host *ha) +{ + /* Advance request queue pointer */ + if (ha->request_in == (REQUEST_QUEUE_DEPTH - 1)) { + ha->request_in = 0; + ha->request_ptr = ha->request_ring; + } else { + ha->request_in++; + ha->request_ptr++; + } +} + /** * qla4xxx_get_req_pkt - returns a valid entry in request queue. * @ha: Pointer to host adapter structure. @@ -26,35 +59,18 @@ static int qla4xxx_get_req_pkt(struct scsi_qla_host *ha, struct queue_entry **queue_entry) { - uint16_t request_in; - uint8_t status = QLA_SUCCESS; - - *queue_entry = ha->request_ptr; + uint16_t req_cnt = 1; - /* get the latest request_in and request_out index */ - request_in = ha->request_in; - ha->request_out = (uint16_t) le32_to_cpu(ha->shadow_regs->req_q_out); - - /* Advance request queue pointer and check for queue full */ - if (request_in == (REQUEST_QUEUE_DEPTH - 1)) { - request_in = 0; - ha->request_ptr = ha->request_ring; - } else { - request_in++; - ha->request_ptr++; - } - - /* request queue is full, try again later */ - if ((ha->iocb_cnt + 1) >= ha->iocb_hiwat) { - /* restore request pointer */ - ha->request_ptr = *queue_entry; - status = QLA_ERROR; - } else { - ha->request_in = request_in; + if (qla4xxx_space_in_req_ring(ha, req_cnt)) { + *queue_entry = ha->request_ptr; memset(*queue_entry, 0, sizeof(**queue_entry)); + + qla4xxx_advance_req_ring_ptr(ha); + ha->req_q_count -= req_cnt; + return QLA_SUCCESS; } - return status; + return QLA_ERROR; } /** @@ -100,21 +116,14 @@ exit_send_marker: return status; } -static struct continuation_t1_entry* qla4xxx_alloc_cont_entry( - struct scsi_qla_host *ha) +static struct continuation_t1_entry * +qla4xxx_alloc_cont_entry(struct scsi_qla_host *ha) { struct continuation_t1_entry *cont_entry; cont_entry = (struct continuation_t1_entry *)ha->request_ptr; - /* Advance request queue pointer */ - if (ha->request_in == (REQUEST_QUEUE_DEPTH - 1)) { - ha->request_in = 0; - ha->request_ptr = ha->request_ring; - } else { - ha->request_in++; - ha->request_ptr++; - } + qla4xxx_advance_req_ring_ptr(ha); /* Load packet defaults */ cont_entry->hdr.entryType = ET_CONTINUE; @@ -197,13 +206,10 @@ int qla4xxx_send_command_to_isp(struct scsi_qla_host *ha, struct srb * srb) struct scsi_cmnd *cmd = srb->cmd; struct ddb_entry *ddb_entry; struct command_t3_entry *cmd_entry; - int nseg; uint16_t tot_dsds; uint16_t req_cnt; - unsigned long flags; - uint16_t cnt; uint32_t index; char tag[2]; @@ -217,6 +223,19 @@ int qla4xxx_send_command_to_isp(struct scsi_qla_host *ha, struct srb * srb) index = (uint32_t)cmd->request->tag; + /* + * Check to see if adapter is online before placing request on + * request queue. If a reset occurs and a request is in the queue, + * the firmware will still attempt to process the request, retrieving + * garbage for pointers. + */ + if (!test_bit(AF_ONLINE, &ha->flags)) { + DEBUG2(printk("scsi%ld: %s: Adapter OFFLINE! " + "Do not issue command.\n", + ha->host_no, __func__)); + goto queuing_error; + } + /* Calculate the number of request entries needed. */ nseg = scsi_dma_map(cmd); if (nseg < 0) @@ -224,17 +243,7 @@ int qla4xxx_send_command_to_isp(struct scsi_qla_host *ha, struct srb * srb) tot_dsds = nseg; req_cnt = qla4xxx_calc_request_entries(tot_dsds); - - if (ha->req_q_count < (req_cnt + 2)) { - cnt = (uint16_t) le32_to_cpu(ha->shadow_regs->req_q_out); - if (ha->request_in < cnt) - ha->req_q_count = cnt - ha->request_in; - else - ha->req_q_count = REQUEST_QUEUE_DEPTH - - (ha->request_in - cnt); - } - - if (ha->req_q_count < (req_cnt + 2)) + if (!qla4xxx_space_in_req_ring(ha, req_cnt)) goto queuing_error; /* total iocbs active */ @@ -286,32 +295,10 @@ int qla4xxx_send_command_to_isp(struct scsi_qla_host *ha, struct srb * srb) break; } - - /* Advance request queue pointer */ - ha->request_in++; - if (ha->request_in == REQUEST_QUEUE_DEPTH) { - ha->request_in = 0; - ha->request_ptr = ha->request_ring; - } else - ha->request_ptr++; - - + qla4xxx_advance_req_ring_ptr(ha); qla4xxx_build_scsi_iocbs(srb, cmd_entry, tot_dsds); wmb(); - /* - * Check to see if adapter is online before placing request on - * request queue. If a reset occurs and a request is in the queue, - * the firmware will still attempt to process the request, retrieving - * garbage for pointers. - */ - if (!test_bit(AF_ONLINE, &ha->flags)) { - DEBUG2(printk("scsi%ld: %s: Adapter OFFLINE! " - "Do not issue command.\n", - ha->host_no, __func__)); - goto queuing_error; - } - srb->cmd->host_scribble = (unsigned char *)srb; /* update counters */ diff --git a/drivers/scsi/qla4xxx/ql4_mbx.c b/drivers/scsi/qla4xxx/ql4_mbx.c index 051b0f5e8c8..09d6d4b76f3 100644 --- a/drivers/scsi/qla4xxx/ql4_mbx.c +++ b/drivers/scsi/qla4xxx/ql4_mbx.c @@ -385,16 +385,6 @@ int qla4xxx_get_firmware_status(struct scsi_qla_host * ha) mbox_sts[0])); return QLA_ERROR; } - - /* High-water mark of IOCBs */ - ha->iocb_hiwat = mbox_sts[2]; - if (ha->iocb_hiwat > IOCB_HIWAT_CUSHION) - ha->iocb_hiwat -= IOCB_HIWAT_CUSHION; - else - dev_info(&ha->pdev->dev, "WARNING!!! You have less than %d " - "firmware IOCBs available (%d).\n", - IOCB_HIWAT_CUSHION, ha->iocb_hiwat); - return QLA_SUCCESS; } -- GitLab From a0cc1ecc098e31d03b3265712a3e280a7fabf438 Mon Sep 17 00:00:00 2001 From: Vasu Dev Date: Tue, 28 Jul 2009 17:33:37 -0700 Subject: [PATCH 0597/1342] [SCSI] libfc: fix a circular locking warning during sending RRQ Currently the fc_exch_rrq is called with fc_exch's ex_lock held. The fc_exch_rrq allocates new exch and that requires taking ex_lock again after EM lock. This locking order causes warning, see more details on this warning at :- http://www.open-fcoe.org/pipermail/devel/2009-July/003251.html This patch fixes this by dropping the ex_lock before calling fc_exch_rrq(). The fc_exch_rrq needs to grab ex_lock lock again to schedule RRQ retry and in the meanwhile fc_exch_reset could occur before ex_lock is grabbed inside fc_exch_rrq. So to handle this case, this patch adds additional check to detect fc_exch_reset after ex_lock acquired and in case the fc_exch_reset occurred then abandons the RRQ retry and releases the exch. Signed-off-by: Vasu Dev Signed-off-by: Robert Love Signed-off-by: James Bottomley --- drivers/scsi/libfc/fc_exch.c | 23 +++++++++++++++-------- 1 file changed, 15 insertions(+), 8 deletions(-) diff --git a/drivers/scsi/libfc/fc_exch.c b/drivers/scsi/libfc/fc_exch.c index 2bc22be5f84..145ab9ba55e 100644 --- a/drivers/scsi/libfc/fc_exch.c +++ b/drivers/scsi/libfc/fc_exch.c @@ -415,9 +415,9 @@ static void fc_exch_timeout(struct work_struct *work) e_stat = ep->esb_stat; if (e_stat & ESB_ST_COMPLETE) { ep->esb_stat = e_stat & ~ESB_ST_REC_QUAL; + spin_unlock_bh(&ep->ex_lock); if (e_stat & ESB_ST_REC_QUAL) fc_exch_rrq(ep); - spin_unlock_bh(&ep->ex_lock); goto done; } else { resp = ep->resp; @@ -1624,14 +1624,14 @@ static void fc_exch_rrq(struct fc_exch *ep) struct fc_lport *lp; struct fc_els_rrq *rrq; struct fc_frame *fp; - struct fc_seq *rrq_sp; u32 did; lp = ep->lp; fp = fc_frame_alloc(lp, sizeof(*rrq)); if (!fp) - return; + goto retry; + rrq = fc_frame_payload_get(fp, sizeof(*rrq)); memset(rrq, 0, sizeof(*rrq)); rrq->rrq_cmd = ELS_RRQ; @@ -1647,13 +1647,20 @@ static void fc_exch_rrq(struct fc_exch *ep) fc_host_port_id(lp->host), FC_TYPE_ELS, FC_FC_FIRST_SEQ | FC_FC_END_SEQ | FC_FC_SEQ_INIT, 0); - rrq_sp = fc_exch_seq_send(lp, fp, fc_exch_rrq_resp, NULL, ep, - lp->e_d_tov); - if (!rrq_sp) { - ep->esb_stat |= ESB_ST_REC_QUAL; - fc_exch_timer_set_locked(ep, ep->r_a_tov); + if (fc_exch_seq_send(lp, fp, fc_exch_rrq_resp, NULL, ep, lp->e_d_tov)) + return; + +retry: + spin_lock_bh(&ep->ex_lock); + if (ep->state & (FC_EX_RST_CLEANUP | FC_EX_DONE)) { + spin_unlock_bh(&ep->ex_lock); + /* drop hold for rec qual */ + fc_exch_release(ep); return; } + ep->esb_stat |= ESB_ST_REC_QUAL; + fc_exch_timer_set_locked(ep, ep->r_a_tov); + spin_unlock_bh(&ep->ex_lock); } -- GitLab From f36f3042eae238bdaefe7c79310afe573bfc3622 Mon Sep 17 00:00:00 2001 From: Chris Mason Date: Thu, 30 Jul 2009 10:04:48 -0400 Subject: [PATCH 0598/1342] Btrfs: be more polite in the async caching threads The semaphore used by the async caching threads can prevent a transaction commit, which can make the FS appear to stall. This releases the semaphore more often when a transaction commit is in progress. Signed-off-by: Chris Mason --- fs/btrfs/extent-tree.c | 5 +++-- fs/btrfs/transaction.c | 10 ++++++++++ fs/btrfs/transaction.h | 1 + 3 files changed, 14 insertions(+), 2 deletions(-) diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c index 2fe21fa7491..dc84daee6bc 100644 --- a/fs/btrfs/extent-tree.c +++ b/fs/btrfs/extent-tree.c @@ -302,10 +302,11 @@ again: else if (ret) break; - if (need_resched()) { + if (need_resched() || + btrfs_transaction_in_commit(fs_info)) { btrfs_release_path(fs_info->extent_root, path); up_read(&fs_info->extent_commit_sem); - cond_resched(); + schedule_timeout(1); goto again; } diff --git a/fs/btrfs/transaction.c b/fs/btrfs/transaction.c index de48e4ec808..cdbb5022da5 100644 --- a/fs/btrfs/transaction.c +++ b/fs/btrfs/transaction.c @@ -857,6 +857,16 @@ static void update_super_roots(struct btrfs_root *root) super->root_level = root_item->level; } +int btrfs_transaction_in_commit(struct btrfs_fs_info *info) +{ + int ret = 0; + spin_lock(&info->new_trans_lock); + if (info->running_transaction) + ret = info->running_transaction->in_commit; + spin_unlock(&info->new_trans_lock); + return ret; +} + int btrfs_commit_transaction(struct btrfs_trans_handle *trans, struct btrfs_root *root) { diff --git a/fs/btrfs/transaction.h b/fs/btrfs/transaction.h index 961c3ee5a2e..663c6740491 100644 --- a/fs/btrfs/transaction.h +++ b/fs/btrfs/transaction.h @@ -107,4 +107,5 @@ int btrfs_record_root_in_trans(struct btrfs_trans_handle *trans, struct btrfs_root *root); int btrfs_write_and_wait_marked_extents(struct btrfs_root *root, struct extent_io_tree *dirty_pages); +int btrfs_transaction_in_commit(struct btrfs_fs_info *info); #endif -- GitLab From 19252de6818ced0def0551d64a0a2975f52a523d Mon Sep 17 00:00:00 2001 From: Tom Peng Date: Fri, 17 Jul 2009 16:02:04 +0800 Subject: [PATCH 0599/1342] [SCSI] libsas: fix wide port hotplug issues Hotplug of phys which form wide ports simply does not work at the moment. Fix this by adding checks at the hotplug points to see if the attached sas address of the phy already exists (in which case it's part of a wide port) and act accordingly. Signed-off-by: Tom Peng Signed-off-by: Jack Wang Signed-off-by: Lindar Liu Signed-off-by: Kevin Ao [jejb: tidied up coding, fixed an error case and made TRUE/FALSE lower case to fix a ppc64 compile error in linux-next] Signed-off-by: James Bottomley --- drivers/scsi/libsas/sas_expander.c | 147 +++++++++++++++++++++-------- 1 file changed, 107 insertions(+), 40 deletions(-) diff --git a/drivers/scsi/libsas/sas_expander.c b/drivers/scsi/libsas/sas_expander.c index 54fa1e42dc4..b3381959acc 100644 --- a/drivers/scsi/libsas/sas_expander.c +++ b/drivers/scsi/libsas/sas_expander.c @@ -766,6 +766,7 @@ static int sas_ex_join_wide_port(struct domain_device *parent, int phy_id) if (!memcmp(phy->attached_sas_addr, ephy->attached_sas_addr, SAS_ADDR_SIZE) && ephy->port) { sas_port_add_phy(ephy->port, phy->phy); + phy->port = ephy->port; phy->phy_state = PHY_DEVICE_DISCOVERED; return 0; } @@ -945,11 +946,21 @@ static int sas_ex_discover_dev(struct domain_device *dev, int phy_id) if (ex->ex_phy[i].phy_state == PHY_VACANT || ex->ex_phy[i].phy_state == PHY_NOT_PRESENT) continue; - + /* + * Due to races, the phy might not get added to the + * wide port, so we add the phy to the wide port here. + */ if (SAS_ADDR(ex->ex_phy[i].attached_sas_addr) == - SAS_ADDR(child->sas_addr)) + SAS_ADDR(child->sas_addr)) { ex->ex_phy[i].phy_state= PHY_DEVICE_DISCOVERED; + res = sas_ex_join_wide_port(dev, i); + if (!res) + SAS_DPRINTK("Attaching ex phy%d to wide port %016llx\n", + i, SAS_ADDR(ex->ex_phy[i].attached_sas_addr)); + + } } + res = 0; } return res; @@ -1598,7 +1609,7 @@ static int sas_get_phy_attached_sas_addr(struct domain_device *dev, } static int sas_find_bcast_phy(struct domain_device *dev, int *phy_id, - int from_phy) + int from_phy, bool update) { struct expander_device *ex = &dev->ex_dev; int res = 0; @@ -1611,7 +1622,9 @@ static int sas_find_bcast_phy(struct domain_device *dev, int *phy_id, if (res) goto out; else if (phy_change_count != ex->ex_phy[i].phy_change_count) { - ex->ex_phy[i].phy_change_count = phy_change_count; + if (update) + ex->ex_phy[i].phy_change_count = + phy_change_count; *phy_id = i; return 0; } @@ -1653,31 +1666,52 @@ out: kfree(rg_req); return res; } +/** + * sas_find_bcast_dev - find the device issue BROADCAST(CHANGE). + * @dev:domain device to be detect. + * @src_dev: the device which originated BROADCAST(CHANGE). + * + * Add self-configuration expander suport. Suppose two expander cascading, + * when the first level expander is self-configuring, hotplug the disks in + * second level expander, BROADCAST(CHANGE) will not only be originated + * in the second level expander, but also be originated in the first level + * expander (see SAS protocol SAS 2r-14, 7.11 for detail), it is to say, + * expander changed count in two level expanders will all increment at least + * once, but the phy which chang count has changed is the source device which + * we concerned. + */ static int sas_find_bcast_dev(struct domain_device *dev, struct domain_device **src_dev) { struct expander_device *ex = &dev->ex_dev; int ex_change_count = -1; + int phy_id = -1; int res; + struct domain_device *ch; res = sas_get_ex_change_count(dev, &ex_change_count); if (res) goto out; - if (ex_change_count != -1 && - ex_change_count != ex->ex_change_count) { - *src_dev = dev; - ex->ex_change_count = ex_change_count; - } else { - struct domain_device *ch; - - list_for_each_entry(ch, &ex->children, siblings) { - if (ch->dev_type == EDGE_DEV || - ch->dev_type == FANOUT_DEV) { - res = sas_find_bcast_dev(ch, src_dev); - if (src_dev) - return res; - } + if (ex_change_count != -1 && ex_change_count != ex->ex_change_count) { + /* Just detect if this expander phys phy change count changed, + * in order to determine if this expander originate BROADCAST, + * and do not update phy change count field in our structure. + */ + res = sas_find_bcast_phy(dev, &phy_id, 0, false); + if (phy_id != -1) { + *src_dev = dev; + ex->ex_change_count = ex_change_count; + SAS_DPRINTK("Expander phy change count has changed\n"); + return res; + } else + SAS_DPRINTK("Expander phys DID NOT change\n"); + } + list_for_each_entry(ch, &ex->children, siblings) { + if (ch->dev_type == EDGE_DEV || ch->dev_type == FANOUT_DEV) { + res = sas_find_bcast_dev(ch, src_dev); + if (src_dev) + return res; } } out: @@ -1700,24 +1734,26 @@ static void sas_unregister_ex_tree(struct domain_device *dev) } static void sas_unregister_devs_sas_addr(struct domain_device *parent, - int phy_id) + int phy_id, bool last) { struct expander_device *ex_dev = &parent->ex_dev; struct ex_phy *phy = &ex_dev->ex_phy[phy_id]; struct domain_device *child, *n; - - list_for_each_entry_safe(child, n, &ex_dev->children, siblings) { - if (SAS_ADDR(child->sas_addr) == - SAS_ADDR(phy->attached_sas_addr)) { - if (child->dev_type == EDGE_DEV || - child->dev_type == FANOUT_DEV) - sas_unregister_ex_tree(child); - else - sas_unregister_dev(child); - break; + if (last) { + list_for_each_entry_safe(child, n, + &ex_dev->children, siblings) { + if (SAS_ADDR(child->sas_addr) == + SAS_ADDR(phy->attached_sas_addr)) { + if (child->dev_type == EDGE_DEV || + child->dev_type == FANOUT_DEV) + sas_unregister_ex_tree(child); + else + sas_unregister_dev(child); + break; + } } + sas_disable_routing(parent, phy->attached_sas_addr); } - sas_disable_routing(parent, phy->attached_sas_addr); memset(phy->attached_sas_addr, 0, SAS_ADDR_SIZE); sas_port_delete_phy(phy->port, phy->phy); if (phy->port->num_phys == 0) @@ -1770,15 +1806,31 @@ static int sas_discover_new(struct domain_device *dev, int phy_id) { struct ex_phy *ex_phy = &dev->ex_dev.ex_phy[phy_id]; struct domain_device *child; - int res; + bool found = false; + int res, i; SAS_DPRINTK("ex %016llx phy%d new device attached\n", SAS_ADDR(dev->sas_addr), phy_id); res = sas_ex_phy_discover(dev, phy_id); if (res) goto out; + /* to support the wide port inserted */ + for (i = 0; i < dev->ex_dev.num_phys; i++) { + struct ex_phy *ex_phy_temp = &dev->ex_dev.ex_phy[i]; + if (i == phy_id) + continue; + if (SAS_ADDR(ex_phy_temp->attached_sas_addr) == + SAS_ADDR(ex_phy->attached_sas_addr)) { + found = true; + break; + } + } + if (found) { + sas_ex_join_wide_port(dev, phy_id); + return 0; + } res = sas_ex_discover_devices(dev, phy_id); - if (res) + if (!res) goto out; list_for_each_entry(child, &dev->ex_dev.children, siblings) { if (SAS_ADDR(child->sas_addr) == @@ -1793,7 +1845,7 @@ out: return res; } -static int sas_rediscover_dev(struct domain_device *dev, int phy_id) +static int sas_rediscover_dev(struct domain_device *dev, int phy_id, bool last) { struct expander_device *ex = &dev->ex_dev; struct ex_phy *phy = &ex->ex_phy[phy_id]; @@ -1804,11 +1856,11 @@ static int sas_rediscover_dev(struct domain_device *dev, int phy_id) switch (res) { case SMP_RESP_NO_PHY: phy->phy_state = PHY_NOT_PRESENT; - sas_unregister_devs_sas_addr(dev, phy_id); + sas_unregister_devs_sas_addr(dev, phy_id, last); goto out; break; case SMP_RESP_PHY_VACANT: phy->phy_state = PHY_VACANT; - sas_unregister_devs_sas_addr(dev, phy_id); + sas_unregister_devs_sas_addr(dev, phy_id, last); goto out; break; case SMP_RESP_FUNC_ACC: break; @@ -1816,7 +1868,7 @@ static int sas_rediscover_dev(struct domain_device *dev, int phy_id) if (SAS_ADDR(attached_sas_addr) == 0) { phy->phy_state = PHY_EMPTY; - sas_unregister_devs_sas_addr(dev, phy_id); + sas_unregister_devs_sas_addr(dev, phy_id, last); } else if (SAS_ADDR(attached_sas_addr) == SAS_ADDR(phy->attached_sas_addr)) { SAS_DPRINTK("ex %016llx phy 0x%x broadcast flutter\n", @@ -1828,12 +1880,27 @@ out: return res; } +/** + * sas_rediscover - revalidate the domain. + * @dev:domain device to be detect. + * @phy_id: the phy id will be detected. + * + * NOTE: this process _must_ quit (return) as soon as any connection + * errors are encountered. Connection recovery is done elsewhere. + * Discover process only interrogates devices in order to discover the + * domain.For plugging out, we un-register the device only when it is + * the last phy in the port, for other phys in this port, we just delete it + * from the port.For inserting, we do discovery when it is the + * first phy,for other phys in this port, we add it to the port to + * forming the wide-port. + */ static int sas_rediscover(struct domain_device *dev, const int phy_id) { struct expander_device *ex = &dev->ex_dev; struct ex_phy *changed_phy = &ex->ex_phy[phy_id]; int res = 0; int i; + bool last = true; /* is this the last phy of the port */ SAS_DPRINTK("ex %016llx phy%d originated BROADCAST(CHANGE)\n", SAS_ADDR(dev->sas_addr), phy_id); @@ -1848,13 +1915,13 @@ static int sas_rediscover(struct domain_device *dev, const int phy_id) SAS_ADDR(changed_phy->attached_sas_addr)) { SAS_DPRINTK("phy%d part of wide port with " "phy%d\n", phy_id, i); - goto out; + last = false; + break; } } - res = sas_rediscover_dev(dev, phy_id); + res = sas_rediscover_dev(dev, phy_id, last); } else res = sas_discover_new(dev, phy_id); -out: return res; } @@ -1881,7 +1948,7 @@ int sas_ex_revalidate_domain(struct domain_device *port_dev) do { phy_id = -1; - res = sas_find_bcast_phy(dev, &phy_id, i); + res = sas_find_bcast_phy(dev, &phy_id, i, true); if (phy_id == -1) break; res = sas_rediscover(dev, phy_id); -- GitLab From 4bf17af0dbfe4cf20cb750e22e8e926273e7a7a4 Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Tue, 14 Jul 2009 19:30:23 +0200 Subject: [PATCH 0600/1342] udf: Fix loading of VAT inode when drive wrongly reports number of recorded blocks VAT inode is located in the last block recorded block of the medium. When the drive errorneously reports number of recorded blocks, we failed to load the VAT inode and thus mount the medium. This patch makes kernel try to read VAT inode from the last block of the device if it is different from the last recorded block. Signed-off-by: Jan Kara --- fs/udf/super.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/fs/udf/super.c b/fs/udf/super.c index 6832135159b..9d1b8c2e6c4 100644 --- a/fs/udf/super.c +++ b/fs/udf/super.c @@ -1087,11 +1087,23 @@ static int udf_load_vat(struct super_block *sb, int p_index, int type1_index) struct udf_inode_info *vati; uint32_t pos; struct virtualAllocationTable20 *vat20; + sector_t blocks = sb->s_bdev->bd_inode->i_size >> sb->s_blocksize_bits; /* VAT file entry is in the last recorded block */ ino.partitionReferenceNum = type1_index; ino.logicalBlockNum = sbi->s_last_block - map->s_partition_root; sbi->s_vat_inode = udf_iget(sb, &ino); + if (!sbi->s_vat_inode && + sbi->s_last_block != blocks - 1) { + printk(KERN_NOTICE "UDF-fs: Failed to read VAT inode from the" + " last recorded block (%lu), retrying with the last " + "block of the device (%lu).\n", + (unsigned long)sbi->s_last_block, + (unsigned long)blocks - 1); + ino.partitionReferenceNum = type1_index; + ino.logicalBlockNum = blocks - 1 - map->s_partition_root; + sbi->s_vat_inode = udf_iget(sb, &ino); + } if (!sbi->s_vat_inode) return 1; -- GitLab From dee865656f2d8b866f8ac22c60d6363b914e9f12 Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Wed, 22 Jul 2009 18:12:17 +0200 Subject: [PATCH 0601/1342] quota: Silence lockdep on quota_on Commit d01730d74d2b0155da50d44555001706294014f7 didn't completely fix the problem since we still take dqio_mutex and i_mutex in the wrong order. Move taking of i_mutex further down (luckily it's needed only for updating inode flags) below where dqio_mutex is taken. Tested-by: Valdis Kletnieks Signed-off-by: Jan Kara --- fs/quota/dquot.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/fs/quota/dquot.c b/fs/quota/dquot.c index 70f36c043d6..38f7bd559f3 100644 --- a/fs/quota/dquot.c +++ b/fs/quota/dquot.c @@ -2043,7 +2043,6 @@ static int vfs_load_quota_inode(struct inode *inode, int type, int format_id, invalidate_bdev(sb->s_bdev); } mutex_lock(&dqopt->dqonoff_mutex); - mutex_lock_nested(&inode->i_mutex, I_MUTEX_QUOTA); if (sb_has_quota_loaded(sb, type)) { error = -EBUSY; goto out_lock; @@ -2054,9 +2053,11 @@ static int vfs_load_quota_inode(struct inode *inode, int type, int format_id, * possible) Also nobody should write to the file - we use * special IO operations which ignore the immutable bit. */ down_write(&dqopt->dqptr_sem); + mutex_lock_nested(&inode->i_mutex, I_MUTEX_QUOTA); oldflags = inode->i_flags & (S_NOATIME | S_IMMUTABLE | S_NOQUOTA); inode->i_flags |= S_NOQUOTA | S_NOATIME | S_IMMUTABLE; + mutex_unlock(&inode->i_mutex); up_write(&dqopt->dqptr_sem); sb->dq_op->drop(inode); } @@ -2080,7 +2081,6 @@ static int vfs_load_quota_inode(struct inode *inode, int type, int format_id, goto out_file_init; } mutex_unlock(&dqopt->dqio_mutex); - mutex_unlock(&inode->i_mutex); spin_lock(&dq_state_lock); dqopt->flags |= dquot_state_flag(flags, type); spin_unlock(&dq_state_lock); @@ -2096,13 +2096,14 @@ out_file_init: out_lock: if (oldflags != -1) { down_write(&dqopt->dqptr_sem); + mutex_lock_nested(&inode->i_mutex, I_MUTEX_QUOTA); /* Set the flags back (in the case of accidental quotaon() * on a wrong file we don't want to mess up the flags) */ inode->i_flags &= ~(S_NOATIME | S_NOQUOTA | S_IMMUTABLE); inode->i_flags |= oldflags; + mutex_unlock(&inode->i_mutex); up_write(&dqopt->dqptr_sem); } - mutex_unlock(&inode->i_mutex); mutex_unlock(&dqopt->dqonoff_mutex); out_fmt: put_quota_format(fmt); -- GitLab From ffd4bc2a984fab40ed969163efdff321490e8032 Mon Sep 17 00:00:00 2001 From: "Martin K. Petersen" Date: Wed, 29 Jul 2009 14:06:53 -0400 Subject: [PATCH 0602/1342] [SCSI] sd: Avoid sending extended inquiry to legacy devices Some USB devices crash when we send them an inquiry with the EVPD bit set, regardless of page requested (i.e. including page 0). We only need the extended inquiry to gain access to VPD pages 0xB0 and 0xB1. These appeared in SBC2 and SBC3 respectively, so we can restrict sending the extended inquiry to devices reporting SPC3 or higher. This fixes bugzilla.kernel.org #13657. Signed-off-by: Martin K. Petersen [jejb: added comment] Signed-off-by: James Bottomley --- drivers/scsi/sd.c | 20 ++++++++++++++++++-- 1 file changed, 18 insertions(+), 2 deletions(-) diff --git a/drivers/scsi/sd.c b/drivers/scsi/sd.c index 5616cd780ff..b7b9fec67a9 100644 --- a/drivers/scsi/sd.c +++ b/drivers/scsi/sd.c @@ -1840,6 +1840,18 @@ static void sd_read_block_characteristics(struct scsi_disk *sdkp) kfree(buffer); } +static int sd_try_extended_inquiry(struct scsi_device *sdp) +{ + /* + * Although VPD inquiries can go to SCSI-2 type devices, + * some USB ones crash on receiving them, and the pages + * we currently ask for are for SPC-3 and beyond + */ + if (sdp->scsi_level > SCSI_SPC_2) + return 1; + return 0; +} + /** * sd_revalidate_disk - called the first time a new disk is seen, * performs disk spin up, read_capacity, etc. @@ -1877,8 +1889,12 @@ static int sd_revalidate_disk(struct gendisk *disk) */ if (sdkp->media_present) { sd_read_capacity(sdkp, buffer); - sd_read_block_limits(sdkp); - sd_read_block_characteristics(sdkp); + + if (sd_try_extended_inquiry(sdp)) { + sd_read_block_limits(sdkp); + sd_read_block_characteristics(sdkp); + } + sd_read_write_protect_flag(sdkp, buffer); sd_read_cache_type(sdkp, buffer); sd_read_app_tag_own(sdkp, buffer); -- GitLab From 2b8d33f714477d1719f96459370037993520de84 Mon Sep 17 00:00:00 2001 From: "ling.ma@intel.com" Date: Wed, 29 Jul 2009 11:31:18 +0800 Subject: [PATCH 0603/1342] drm/i915: Return disconnected for SDVO DVI when there's no digital EDID. The patch fixed a bug on MP965-D. When VGA is connected to a DVI-I connector, it incorrectly shows sdvo dvi as connected. Signed-off-by: Ma Ling [anholt: hand-resolved against previous commit and fixed up commit message] Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_sdvo.c | 27 +++++++++++++++++++++------ 1 file changed, 21 insertions(+), 6 deletions(-) diff --git a/drivers/gpu/drm/i915/intel_sdvo.c b/drivers/gpu/drm/i915/intel_sdvo.c index b68746f0380..5371d933255 100644 --- a/drivers/gpu/drm/i915/intel_sdvo.c +++ b/drivers/gpu/drm/i915/intel_sdvo.c @@ -31,6 +31,7 @@ #include "drm.h" #include "drm_crtc.h" #include "intel_drv.h" +#include "drm_edid.h" #include "i915_drm.h" #include "i915_drv.h" #include "intel_sdvo_regs.h" @@ -1477,20 +1478,35 @@ intel_sdvo_multifunc_encoder(struct intel_output *intel_output) return (caps > 1); } -static void -intel_sdvo_hdmi_sink_detect(struct drm_connector *connector) +enum drm_connector_status +intel_sdvo_hdmi_sink_detect(struct drm_connector *connector, u16 response) { struct intel_output *intel_output = to_intel_output(connector); struct intel_sdvo_priv *sdvo_priv = intel_output->dev_priv; + enum drm_connector_status status = connector_status_connected; struct edid *edid = NULL; edid = drm_get_edid(&intel_output->base, intel_output->ddc_bus); if (edid != NULL) { - sdvo_priv->is_hdmi = drm_detect_hdmi_monitor(edid); + /* Don't report the output as connected if it's a DVI-I + * connector with a non-digital EDID coming out. + */ + if (response & (SDVO_OUTPUT_TMDS0 | SDVO_OUTPUT_TMDS1)) { + if (edid->input & DRM_EDID_INPUT_DIGITAL) + sdvo_priv->is_hdmi = + drm_detect_hdmi_monitor(edid); + else + status = connector_status_disconnected; + } + kfree(edid); intel_output->base.display_info.raw_edid = NULL; - } + + } else if (response & (SDVO_OUTPUT_TMDS0 | SDVO_OUTPUT_TMDS1)) + status = connector_status_disconnected; + + return status; } static enum drm_connector_status intel_sdvo_detect(struct drm_connector *connector) @@ -1518,8 +1534,7 @@ static enum drm_connector_status intel_sdvo_detect(struct drm_connector *connect return connector_status_unknown; sdvo_priv->attached_output = response; } - intel_sdvo_hdmi_sink_detect(connector); - return connector_status_connected; + return intel_sdvo_hdmi_sink_detect(connector, response); } static void intel_sdvo_get_ddc_modes(struct drm_connector *connector) -- GitLab From 0c2e39525b3b53a97a0202c5f35058147e53977e Mon Sep 17 00:00:00 2001 From: "ling.ma@intel.com" Date: Fri, 17 Jul 2009 11:44:30 +0800 Subject: [PATCH 0604/1342] drm/i915: Add support for dual-channel LVDS on 8xx. This corresponds to a fix to UMS back in 2007. Fixes fd.o bug #20115. Signed-off-by: Ma Ling Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_display.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 1da7b0b9ed3..d6fce213341 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -90,7 +90,7 @@ struct intel_limit { #define I8XX_P2_SLOW 4 #define I8XX_P2_FAST 2 #define I8XX_P2_LVDS_SLOW 14 -#define I8XX_P2_LVDS_FAST 14 /* No fast option */ +#define I8XX_P2_LVDS_FAST 7 #define I8XX_P2_SLOW_LIMIT 165000 #define I9XX_DOT_MIN 20000 -- GitLab From ca7daea612b480ecf0fc5bd1630b88447fe73fc5 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Thu, 30 Jul 2009 04:38:19 +0000 Subject: [PATCH 0605/1342] net/netlabel: Add kmalloc NULL tests The test on map4 should be a test on map6. The semantic match that finds this problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // @@ expression *x; identifier f; constant char *C; @@ x = \(kmalloc\|kcalloc\|kzalloc\)(...); ... when != x == NULL when != x != NULL when != (x || ...) ( kfree(x) | f(...,C,...,x,...) | *f(...,x,...) | *x->f ) // Signed-off-by: Julia Lawall Acked-by: Paul Moore Signed-off-by: David S. Miller --- net/netlabel/netlabel_kapi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/netlabel/netlabel_kapi.c b/net/netlabel/netlabel_kapi.c index b0e582f2d37..16e6c4378ff 100644 --- a/net/netlabel/netlabel_kapi.c +++ b/net/netlabel/netlabel_kapi.c @@ -151,7 +151,7 @@ int netlbl_cfg_unlbl_map_add(const char *domain, addr6 = addr; mask6 = mask; map6 = kzalloc(sizeof(*map6), GFP_ATOMIC); - if (map4 == NULL) + if (map6 == NULL) goto cfg_unlbl_map_add_failure; map6->type = NETLBL_NLTYPE_UNLABELED; ipv6_addr_copy(&map6->list.addr, addr6); -- GitLab From a541f8401d8e9113a89ee902cb8d8e412d6d3569 Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Wed, 29 Jul 2009 08:49:52 +0000 Subject: [PATCH 0606/1342] iscsi: Use GFP_ATOMIC in iscsi_offload_mesg(). Changing to GFP_ATOMIC because the only caller in cnic/bnx2i may be calling this function while holding spin_lock. This problem was discovered by Mike Christie. Signed-off-by: Michael Chan Acked-by: Mike Christie Signed-off-by: David S. Miller --- drivers/scsi/scsi_transport_iscsi.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/scsi/scsi_transport_iscsi.c b/drivers/scsi/scsi_transport_iscsi.c index 783e33c65eb..b47240ca4b1 100644 --- a/drivers/scsi/scsi_transport_iscsi.c +++ b/drivers/scsi/scsi_transport_iscsi.c @@ -990,7 +990,7 @@ int iscsi_offload_mesg(struct Scsi_Host *shost, struct iscsi_uevent *ev; int len = NLMSG_SPACE(sizeof(*ev) + data_size); - skb = alloc_skb(len, GFP_NOIO); + skb = alloc_skb(len, GFP_ATOMIC); if (!skb) { printk(KERN_ERR "can not deliver iscsi offload message:OOM\n"); return -ENOMEM; @@ -1012,7 +1012,7 @@ int iscsi_offload_mesg(struct Scsi_Host *shost, memcpy((char *)ev + sizeof(*ev), data, data_size); - return iscsi_multicast_skb(skb, ISCSI_NL_GRP_UIP, GFP_NOIO); + return iscsi_multicast_skb(skb, ISCSI_NL_GRP_UIP, GFP_ATOMIC); } EXPORT_SYMBOL_GPL(iscsi_offload_mesg); -- GitLab From e9956fae7dbce6ac770e7a00436c496ddbbd3215 Mon Sep 17 00:00:00 2001 From: Tao Ma Date: Thu, 30 Jul 2009 16:07:10 +0800 Subject: [PATCH 0607/1342] ocfs2/quota: Release lock for error in ocfs2_quota_write. ocfs2_quota_write needs to release the lock if it fails to read quota block. So use "goto out" instead of "return err". Signed-off-by: Tao Ma Acked-by: Jan Kara Signed-off-by: Joel Becker --- fs/ocfs2/quota_global.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/ocfs2/quota_global.c b/fs/ocfs2/quota_global.c index cc8785cf8f6..d604a6aa0a2 100644 --- a/fs/ocfs2/quota_global.c +++ b/fs/ocfs2/quota_global.c @@ -238,7 +238,7 @@ ssize_t ocfs2_quota_write(struct super_block *sb, int type, } if (err) { mlog_errno(err); - return err; + goto out; } lock_buffer(bh); if (new) -- GitLab From 2a8aaacda5097fa92a39948da1b4c6614b6e150e Mon Sep 17 00:00:00 2001 From: Tobias Klauser Date: Thu, 30 Jul 2009 13:10:50 -0700 Subject: [PATCH 0608/1342] docbook: fix printk of ip address Use the %pI4 format string instead of %d.%d.%d.%d and NIPQUAD. Signed-off-by: Tobias Klauser Signed-off-by: Randy Dunlap Signed-off-by: David S. Miller --- Documentation/DocBook/kernel-hacking.tmpl | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/Documentation/DocBook/kernel-hacking.tmpl b/Documentation/DocBook/kernel-hacking.tmpl index a50d6cd5857..992e67e6be7 100644 --- a/Documentation/DocBook/kernel-hacking.tmpl +++ b/Documentation/DocBook/kernel-hacking.tmpl @@ -449,8 +449,8 @@ printk(KERN_INFO "i = %u\n", i); -__u32 ipaddress; -printk(KERN_INFO "my ip: %d.%d.%d.%d\n", NIPQUAD(ipaddress)); +__be32 ipaddress; +printk(KERN_INFO "my ip: %pI4\n", &ipaddress); -- GitLab From 3d54015b750e5d5e950a1dcee2735387fd4b6e1a Mon Sep 17 00:00:00 2001 From: roel kluin Date: Thu, 30 Jul 2009 00:26:32 +0000 Subject: [PATCH 0609/1342] 3c515: Write outside array bounds if dev_alloc_skb() fails on the first iteration, a write to cp->rx_ring[-1] occurs. Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/3c515.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/net/3c515.c b/drivers/net/3c515.c index 3e00fa8ea65..4a7c32895be 100644 --- a/drivers/net/3c515.c +++ b/drivers/net/3c515.c @@ -832,7 +832,9 @@ static int corkscrew_open(struct net_device *dev) skb_reserve(skb, 2); /* Align IP on 16 byte boundaries */ vp->rx_ring[i].addr = isa_virt_to_bus(skb->data); } - vp->rx_ring[i - 1].next = isa_virt_to_bus(&vp->rx_ring[0]); /* Wrap the ring. */ + if (i != 0) + vp->rx_ring[i - 1].next = + isa_virt_to_bus(&vp->rx_ring[0]); /* Wrap the ring. */ outl(isa_virt_to_bus(&vp->rx_ring[0]), ioaddr + UpListPtr); } if (vp->full_bus_master_tx) { /* Boomerang bus master Tx. */ -- GitLab From a3e8ee682003685b8b9c98c89340a42e48c3e813 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Wed, 29 Jul 2009 23:46:59 +0000 Subject: [PATCH 0610/1342] ipv4: ARP neigh procfs buffer overflow If arp_format_neigh_entry() can be called with n->dev->addr_len == 0, then a write to hbuffer[-1] occurs. Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- net/ipv4/arp.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/net/ipv4/arp.c b/net/ipv4/arp.c index c29d75d8f1b..090e9991ac2 100644 --- a/net/ipv4/arp.c +++ b/net/ipv4/arp.c @@ -1304,7 +1304,9 @@ static void arp_format_neigh_entry(struct seq_file *seq, hbuffer[k++] = hex_asc_lo(n->ha[j]); hbuffer[k++] = ':'; } - hbuffer[--k] = 0; + if (k != 0) + --k; + hbuffer[k] = 0; #if defined(CONFIG_AX25) || defined(CONFIG_AX25_MODULE) } #endif -- GitLab From f0c5b35c6c93c89a9d8ccab19b0b4842f5dfddc5 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Wed, 29 Jul 2009 03:18:56 +0000 Subject: [PATCH 0611/1342] eexpress: Read buffer overflow start_code is 69 words, but the code always writes a multiple of 16 words, so the last 11 words written are outside the array. Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/eexpress.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/net/eexpress.c b/drivers/net/eexpress.c index 1686dca2874..1f016d66684 100644 --- a/drivers/net/eexpress.c +++ b/drivers/net/eexpress.c @@ -1474,13 +1474,13 @@ static void eexp_hw_init586(struct net_device *dev) outw(0x0000, ioaddr + 0x800c); outw(0x0000, ioaddr + 0x800e); - for (i = 0; i < (sizeof(start_code)); i+=32) { + for (i = 0; i < ARRAY_SIZE(start_code) * 2; i+=32) { int j; outw(i, ioaddr + SM_PTR); - for (j = 0; j < 16; j+=2) + for (j = 0; j < 16 && (i+j)/2 < ARRAY_SIZE(start_code); j+=2) outw(start_code[(i+j)/2], ioaddr+0x4000+j); - for (j = 0; j < 16; j+=2) + for (j = 0; j < 16 && (i+j+16)/2 < ARRAY_SIZE(start_code); j+=2) outw(start_code[(i+j+16)/2], ioaddr+0x8000+j); } -- GitLab From daed953721850381673687c59f3a0df553eb6626 Mon Sep 17 00:00:00 2001 From: Frans Pop Date: Thu, 30 Jul 2009 17:16:05 -0400 Subject: [PATCH 0612/1342] hp-wmi: check that an input device exists in resume handler MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Some systems may not support input events, or registering the input handler may have failed. So check that an input device exists before trying to set the docking and tablet mode state during resume. Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=13865 Reported-and-tested-by: Cédric Godin Signed-off-by: Frans Pop Acked-by: Matthew Garrett Signed-off-by: Len Brown --- drivers/platform/x86/hp-wmi.c | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-) diff --git a/drivers/platform/x86/hp-wmi.c b/drivers/platform/x86/hp-wmi.c index ca508564a18..a2ad53e1587 100644 --- a/drivers/platform/x86/hp-wmi.c +++ b/drivers/platform/x86/hp-wmi.c @@ -520,11 +520,13 @@ static int hp_wmi_resume_handler(struct platform_device *device) * the input layer will only actually pass it on if the state * changed. */ - - input_report_switch(hp_wmi_input_dev, SW_DOCK, hp_wmi_dock_state()); - input_report_switch(hp_wmi_input_dev, SW_TABLET_MODE, - hp_wmi_tablet_state()); - input_sync(hp_wmi_input_dev); + if (hp_wmi_input_dev) { + input_report_switch(hp_wmi_input_dev, SW_DOCK, + hp_wmi_dock_state()); + input_report_switch(hp_wmi_input_dev, SW_TABLET_MODE, + hp_wmi_tablet_state()); + input_sync(hp_wmi_input_dev); + } return 0; } -- GitLab From 72fc939789dbe7ca091b50b686d45ac0df15417a Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Tue, 28 Jul 2009 23:43:08 +0000 Subject: [PATCH 0613/1342] pppoe: fix /proc/net/pppoe If a socket is hashed in last slot of pppoe hash table (PPPOE_HASH_SIZE-1) we report it many times (up to filling seq buffer) (Only the last socket of last slot) Signed-off-by: Eric Dumazet Signed-off-by: David S. Miller --- drivers/net/pppoe.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/net/pppoe.c b/drivers/net/pppoe.c index f0031f1f97e..5f2090233d7 100644 --- a/drivers/net/pppoe.c +++ b/drivers/net/pppoe.c @@ -1063,6 +1063,7 @@ static void *pppoe_seq_next(struct seq_file *seq, void *v, loff_t *pos) else { int hash = hash_item(po->pppoe_pa.sid, po->pppoe_pa.remote); + po = NULL; while (++hash < PPPOE_HASH_SIZE) { po = pn->hash_table[hash]; if (po) -- GitLab From accff95c2500c7bce671c1f722de6f8810fe550d Mon Sep 17 00:00:00 2001 From: Jiajun Wu Date: Thu, 30 Jul 2009 14:20:42 -0700 Subject: [PATCH 0614/1342] gianfar: fix coalescing setup in ethtool support Parameter order for using mk_ic_value(count, time) was reversed, the patch fixes this. Signed-off-by: Jiajun Wu Signed-off-by: Li Yang Signed-off-by: David S. Miller --- drivers/net/gianfar_ethtool.c | 10 ++++------ 1 file changed, 4 insertions(+), 6 deletions(-) diff --git a/drivers/net/gianfar_ethtool.c b/drivers/net/gianfar_ethtool.c index dbf06e9313c..2234118eedb 100644 --- a/drivers/net/gianfar_ethtool.c +++ b/drivers/net/gianfar_ethtool.c @@ -366,9 +366,8 @@ static int gfar_scoalesce(struct net_device *dev, struct ethtool_coalesce *cvals return -EINVAL; } - priv->rxic = mk_ic_value( - gfar_usecs2ticks(priv, cvals->rx_coalesce_usecs), - cvals->rx_max_coalesced_frames); + priv->rxic = mk_ic_value(cvals->rx_max_coalesced_frames, + gfar_usecs2ticks(priv, cvals->rx_coalesce_usecs)); /* Set up tx coalescing */ if ((cvals->tx_coalesce_usecs == 0) || @@ -390,9 +389,8 @@ static int gfar_scoalesce(struct net_device *dev, struct ethtool_coalesce *cvals return -EINVAL; } - priv->txic = mk_ic_value( - gfar_usecs2ticks(priv, cvals->tx_coalesce_usecs), - cvals->tx_max_coalesced_frames); + priv->txic = mk_ic_value(cvals->tx_max_coalesced_frames, + gfar_usecs2ticks(priv, cvals->tx_coalesce_usecs)); gfar_write(&priv->regs->rxic, 0); if (priv->rxcoalescing) -- GitLab From 165f5f64199f972a21f21effc125d89ed2488e58 Mon Sep 17 00:00:00 2001 From: Peter Korsgaard Date: Wed, 1 Jul 2009 17:47:08 +0200 Subject: [PATCH 0615/1342] ARM: S3C: PWM fix for low duty cycle The pwm hardware only checks the compare register after a decrement, so the pin never toggles if tcmp = tcnt. This happens when a very low duty cycle is requested. Fix it by always ensuring that tcmp < tcnt. Signed-off-by: Peter Korsgaard Signed-off-by: Ben Dooks --- arch/arm/plat-s3c24xx/pwm.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/plat-s3c24xx/pwm.c b/arch/arm/plat-s3c24xx/pwm.c index 0120b760315..82a6d4de02a 100644 --- a/arch/arm/plat-s3c24xx/pwm.c +++ b/arch/arm/plat-s3c24xx/pwm.c @@ -246,6 +246,10 @@ int pwm_config(struct pwm_device *pwm, int duty_ns, int period_ns) tcmp = duty_ns / tin_ns; tcmp = tcnt - tcmp; + /* the pwm hw only checks the compare register after a decrement, + so the pin never toggles if tcmp = tcnt */ + if (tcmp == tcnt) + tcmp--; pwm_dbg(pwm, "tin_ns=%lu, tcmp=%ld/%lu\n", tin_ns, tcmp, tcnt); -- GitLab From 8fe70a5f7167e02bbc18086970f0e92a5e55b80d Mon Sep 17 00:00:00 2001 From: Ramax Lo Date: Thu, 9 Jul 2009 16:28:33 +0800 Subject: [PATCH 0616/1342] ARM: S3C24XX: serial: Fix section mismatch warnings During kernel build process, the following warning was found: WARNING: drivers/serial/built-in.o(.data+0x304): Section mismatch in reference from the variable s3c2440_serial_drv to the function .devexit.text:s3c24xx_serial_remove() The variable s3c2440_serial_drv references the function __devexit s3c24xx_serial_remove() If the reference is valid then annotate the variable with __exit* (see linux/init.h) or name the variable: *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, The same warning happened for s3c241x platform. We rename variables to avoid these warnings. These changes also apply to s3c2400 & s3c24a0 for consistency. Signed-off-by: Ramax Lo Signed-off-by: Ben Dooks --- drivers/serial/s3c2400.c | 8 ++++---- drivers/serial/s3c2410.c | 8 ++++---- drivers/serial/s3c2412.c | 8 ++++---- drivers/serial/s3c2440.c | 8 ++++---- drivers/serial/s3c24a0.c | 8 ++++---- 5 files changed, 20 insertions(+), 20 deletions(-) diff --git a/drivers/serial/s3c2400.c b/drivers/serial/s3c2400.c index fb00ed5296e..fed1a9a1ffb 100644 --- a/drivers/serial/s3c2400.c +++ b/drivers/serial/s3c2400.c @@ -76,7 +76,7 @@ static int s3c2400_serial_probe(struct platform_device *dev) return s3c24xx_serial_probe(dev, &s3c2400_uart_inf); } -static struct platform_driver s3c2400_serial_drv = { +static struct platform_driver s3c2400_serial_driver = { .probe = s3c2400_serial_probe, .remove = __devexit_p(s3c24xx_serial_remove), .driver = { @@ -85,16 +85,16 @@ static struct platform_driver s3c2400_serial_drv = { }, }; -s3c24xx_console_init(&s3c2400_serial_drv, &s3c2400_uart_inf); +s3c24xx_console_init(&s3c2400_serial_driver, &s3c2400_uart_inf); static inline int s3c2400_serial_init(void) { - return s3c24xx_serial_init(&s3c2400_serial_drv, &s3c2400_uart_inf); + return s3c24xx_serial_init(&s3c2400_serial_driver, &s3c2400_uart_inf); } static inline void s3c2400_serial_exit(void) { - platform_driver_unregister(&s3c2400_serial_drv); + platform_driver_unregister(&s3c2400_serial_driver); } module_init(s3c2400_serial_init); diff --git a/drivers/serial/s3c2410.c b/drivers/serial/s3c2410.c index b5d7cbcba2a..c99f0821cae 100644 --- a/drivers/serial/s3c2410.c +++ b/drivers/serial/s3c2410.c @@ -88,7 +88,7 @@ static int s3c2410_serial_probe(struct platform_device *dev) return s3c24xx_serial_probe(dev, &s3c2410_uart_inf); } -static struct platform_driver s3c2410_serial_drv = { +static struct platform_driver s3c2410_serial_driver = { .probe = s3c2410_serial_probe, .remove = __devexit_p(s3c24xx_serial_remove), .driver = { @@ -97,16 +97,16 @@ static struct platform_driver s3c2410_serial_drv = { }, }; -s3c24xx_console_init(&s3c2410_serial_drv, &s3c2410_uart_inf); +s3c24xx_console_init(&s3c2410_serial_driver, &s3c2410_uart_inf); static int __init s3c2410_serial_init(void) { - return s3c24xx_serial_init(&s3c2410_serial_drv, &s3c2410_uart_inf); + return s3c24xx_serial_init(&s3c2410_serial_driver, &s3c2410_uart_inf); } static void __exit s3c2410_serial_exit(void) { - platform_driver_unregister(&s3c2410_serial_drv); + platform_driver_unregister(&s3c2410_serial_driver); } module_init(s3c2410_serial_init); diff --git a/drivers/serial/s3c2412.c b/drivers/serial/s3c2412.c index 11dcb90bdfe..6e057d8809d 100644 --- a/drivers/serial/s3c2412.c +++ b/drivers/serial/s3c2412.c @@ -121,7 +121,7 @@ static int s3c2412_serial_probe(struct platform_device *dev) return s3c24xx_serial_probe(dev, &s3c2412_uart_inf); } -static struct platform_driver s3c2412_serial_drv = { +static struct platform_driver s3c2412_serial_driver = { .probe = s3c2412_serial_probe, .remove = __devexit_p(s3c24xx_serial_remove), .driver = { @@ -130,16 +130,16 @@ static struct platform_driver s3c2412_serial_drv = { }, }; -s3c24xx_console_init(&s3c2412_serial_drv, &s3c2412_uart_inf); +s3c24xx_console_init(&s3c2412_serial_driver, &s3c2412_uart_inf); static inline int s3c2412_serial_init(void) { - return s3c24xx_serial_init(&s3c2412_serial_drv, &s3c2412_uart_inf); + return s3c24xx_serial_init(&s3c2412_serial_driver, &s3c2412_uart_inf); } static inline void s3c2412_serial_exit(void) { - platform_driver_unregister(&s3c2412_serial_drv); + platform_driver_unregister(&s3c2412_serial_driver); } module_init(s3c2412_serial_init); diff --git a/drivers/serial/s3c2440.c b/drivers/serial/s3c2440.c index 06c5b0cc47a..69ff5d340f0 100644 --- a/drivers/serial/s3c2440.c +++ b/drivers/serial/s3c2440.c @@ -151,7 +151,7 @@ static int s3c2440_serial_probe(struct platform_device *dev) return s3c24xx_serial_probe(dev, &s3c2440_uart_inf); } -static struct platform_driver s3c2440_serial_drv = { +static struct platform_driver s3c2440_serial_driver = { .probe = s3c2440_serial_probe, .remove = __devexit_p(s3c24xx_serial_remove), .driver = { @@ -160,16 +160,16 @@ static struct platform_driver s3c2440_serial_drv = { }, }; -s3c24xx_console_init(&s3c2440_serial_drv, &s3c2440_uart_inf); +s3c24xx_console_init(&s3c2440_serial_driver, &s3c2440_uart_inf); static int __init s3c2440_serial_init(void) { - return s3c24xx_serial_init(&s3c2440_serial_drv, &s3c2440_uart_inf); + return s3c24xx_serial_init(&s3c2440_serial_driver, &s3c2440_uart_inf); } static void __exit s3c2440_serial_exit(void) { - platform_driver_unregister(&s3c2440_serial_drv); + platform_driver_unregister(&s3c2440_serial_driver); } module_init(s3c2440_serial_init); diff --git a/drivers/serial/s3c24a0.c b/drivers/serial/s3c24a0.c index 786a067d62a..26c49e18bdd 100644 --- a/drivers/serial/s3c24a0.c +++ b/drivers/serial/s3c24a0.c @@ -92,7 +92,7 @@ static int s3c24a0_serial_probe(struct platform_device *dev) return s3c24xx_serial_probe(dev, &s3c24a0_uart_inf); } -static struct platform_driver s3c24a0_serial_drv = { +static struct platform_driver s3c24a0_serial_driver = { .probe = s3c24a0_serial_probe, .remove = __devexit_p(s3c24xx_serial_remove), .driver = { @@ -101,16 +101,16 @@ static struct platform_driver s3c24a0_serial_drv = { }, }; -s3c24xx_console_init(&s3c24a0_serial_drv, &s3c24a0_uart_inf); +s3c24xx_console_init(&s3c24a0_serial_driver, &s3c24a0_uart_inf); static int __init s3c24a0_serial_init(void) { - return s3c24xx_serial_init(&s3c24a0_serial_drv, &s3c24a0_uart_inf); + return s3c24xx_serial_init(&s3c24a0_serial_driver, &s3c24a0_uart_inf); } static void __exit s3c24a0_serial_exit(void) { - platform_driver_unregister(&s3c24a0_serial_drv); + platform_driver_unregister(&s3c24a0_serial_driver); } module_init(s3c24a0_serial_init); -- GitLab From 909db80297ba65699a77d877f7bf618ba960f6fc Mon Sep 17 00:00:00 2001 From: Ramax Lo Date: Fri, 10 Jul 2009 19:30:56 +0800 Subject: [PATCH 0617/1342] ARM: S3C64XX: serial: Fix section mismatch warning Rename the structure to avoid the following warning: WARNING: vmlinux.o(.data+0x11ef4): Section mismatch in reference from the variable s3c6400_serial_drv to the function .devexit.text:s3c24xx_serial_remove() The variable s3c6400_serial_drv references the function __devexit s3c24xx_serial_remove() If the reference is valid then annotate the variable with __exit* (see linux/init.h) or name the variable: *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, Signed-off-by: Ramax Lo Signed-off-by: Ben Dooks --- drivers/serial/s3c6400.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/serial/s3c6400.c b/drivers/serial/s3c6400.c index 48f1a3781f0..4be92ab5005 100644 --- a/drivers/serial/s3c6400.c +++ b/drivers/serial/s3c6400.c @@ -122,7 +122,7 @@ static int s3c6400_serial_probe(struct platform_device *dev) return s3c24xx_serial_probe(dev, &s3c6400_uart_inf); } -static struct platform_driver s3c6400_serial_drv = { +static struct platform_driver s3c6400_serial_driver = { .probe = s3c6400_serial_probe, .remove = __devexit_p(s3c24xx_serial_remove), .driver = { @@ -131,16 +131,16 @@ static struct platform_driver s3c6400_serial_drv = { }, }; -s3c24xx_console_init(&s3c6400_serial_drv, &s3c6400_uart_inf); +s3c24xx_console_init(&s3c6400_serial_driver, &s3c6400_uart_inf); static int __init s3c6400_serial_init(void) { - return s3c24xx_serial_init(&s3c6400_serial_drv, &s3c6400_uart_inf); + return s3c24xx_serial_init(&s3c6400_serial_driver, &s3c6400_uart_inf); } static void __exit s3c6400_serial_exit(void) { - platform_driver_unregister(&s3c6400_serial_drv); + platform_driver_unregister(&s3c6400_serial_driver); } module_init(s3c6400_serial_init); -- GitLab From 90a09c9cf78344d18e2438c3b87363b949629fa3 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Thu, 30 Jul 2009 16:40:37 -0700 Subject: [PATCH 0618/1342] Alan doesn't want to maintain tty code any more Not that anybody can blame him. It's a morass. But hey, it's way better than it _used_ to be, though, so thanks for all the fish. Signed-off-by: Linus Torvalds --- MAINTAINERS | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index 66a3865da88..79471ba4981 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -155,10 +155,9 @@ S: Maintained F: drivers/net/r8169.c 8250/16?50 (AND CLONE UARTS) SERIAL DRIVER -M: Alan Cox L: linux-serial@vger.kernel.org W: http://serial.sourceforge.net -S: Odd Fixes +S: Orphan F: drivers/serial/8250* F: include/linux/serial_8250.h @@ -4997,9 +4996,7 @@ T: git git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial.git S: Maintained TTY LAYER -M: Alan Cox -S: Maintained -T: stgit http://zeniv.linux.org.uk/~alan/ttydev/ +S: Orphan F: drivers/char/tty_* F: drivers/serial/serial_core.c F: include/linux/serial_core.h -- GitLab From ec30c5f3a18722f8fcf8c83146a10b03ac4d9ff1 Mon Sep 17 00:00:00 2001 From: Masami Hiramatsu Date: Tue, 28 Jul 2009 19:47:23 -0400 Subject: [PATCH 0619/1342] kprobes: Use kernel_text_address() for checking probe address Use kernel_text_address() for checking probe address instead of __kernel_text_address(), because __kernel_text_address() returns true for init functions even after relaseing those functions. That will hit a BUG() in text_poke(). Signed-off-by: Masami Hiramatsu Cc: Ananth N Mavinakayanahalli Cc: Jim Keniston Signed-off-by: Linus Torvalds --- kernel/kprobes.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/kprobes.c b/kernel/kprobes.c index 16b5739c516..0540948e29a 100644 --- a/kernel/kprobes.c +++ b/kernel/kprobes.c @@ -694,7 +694,7 @@ int __kprobes register_kprobe(struct kprobe *p) p->addr = addr; preempt_disable(); - if (!__kernel_text_address((unsigned long) p->addr) || + if (!kernel_text_address((unsigned long) p->addr) || in_kprobes_functions((unsigned long) p->addr)) { preempt_enable(); return -EINVAL; -- GitLab From bdc6340f4eb68295b1e7c0ade2356b56dca93d93 Mon Sep 17 00:00:00 2001 From: "Pallipadi, Venkatesh" Date: Thu, 30 Jul 2009 14:43:19 -0700 Subject: [PATCH 0620/1342] x86, pat: Fix set_memory_wc related corruption Changeset 3869c4aa18835c8c61b44bd0f3ace36e9d3b5bd0 that went in after 2.6.30-rc1 was a seemingly small change to _set_memory_wc() to make it complaint with SDM requirements. But, introduced a nasty bug, which can result in crash and/or strange corruptions when set_memory_wc is used. One such crash reported here http://lkml.org/lkml/2009/7/30/94 Actually, that changeset introduced two bugs. * change_page_attr_set() takes &addr as first argument and can the addr value might have changed on return, even for single page change_page_attr_set() call. That will make the second change_page_attr_set() in this routine operate on unrelated addr, that can eventually cause strange corruptions and bad page state crash. * The second change_page_attr_set() call, before setting _PAGE_CACHE_WC, should clear the earlier _PAGE_CACHE_UC_MINUS, as otherwise cache attribute will not be WC (will be UC instead). The patch below fixes both these problems. Sending a single patch to fix both the problems, as the change is to the same line of code. The change to have a addr_copy is not very clean. But, it is simpler than making more changes through various routines in pageattr.c. A huge thanks to Jerome for reporting this problem and providing a simple test case that helped us root cause the problem. Reported-by: Jerome Glisse Signed-off-by: Venkatesh Pallipadi Signed-off-by: Suresh Siddha LKML-Reference: <20090730214319.GA1889@linux-os.sc.intel.com> Acked-by: Dave Airlie Signed-off-by: H. Peter Anvin --- arch/x86/mm/pageattr.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) diff --git a/arch/x86/mm/pageattr.c b/arch/x86/mm/pageattr.c index 1b734d7a896..895d90e1a81 100644 --- a/arch/x86/mm/pageattr.c +++ b/arch/x86/mm/pageattr.c @@ -997,12 +997,15 @@ EXPORT_SYMBOL(set_memory_array_uc); int _set_memory_wc(unsigned long addr, int numpages) { int ret; + unsigned long addr_copy = addr; + ret = change_page_attr_set(&addr, numpages, __pgprot(_PAGE_CACHE_UC_MINUS), 0); - if (!ret) { - ret = change_page_attr_set(&addr, numpages, - __pgprot(_PAGE_CACHE_WC), 0); + ret = change_page_attr_set_clr(&addr_copy, numpages, + __pgprot(_PAGE_CACHE_WC), + __pgprot(_PAGE_CACHE_MASK), + 0, 0, NULL); } return ret; } -- GitLab From 8f9a71673d9f397a365f4d18c307e91141b8fe92 Mon Sep 17 00:00:00 2001 From: Peter P Waskiewicz Jr Date: Thu, 30 Jul 2009 12:25:09 +0000 Subject: [PATCH 0621/1342] ixgbe: Fix netpoll to be properly multiqueue aware Our ndo_poll_controller callback is broken for anything but non-multiqueue setups. This fixes that issue. Signed-off-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_main.c | 13 ++++++++++--- 1 file changed, 10 insertions(+), 3 deletions(-) diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index 200454f30f6..60c4a8bf7d3 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -5360,12 +5360,19 @@ static int ixgbe_del_sanmac_netdev(struct net_device *dev) static void ixgbe_netpoll(struct net_device *netdev) { struct ixgbe_adapter *adapter = netdev_priv(netdev); + int i; - disable_irq(adapter->pdev->irq); adapter->flags |= IXGBE_FLAG_IN_NETPOLL; - ixgbe_intr(adapter->pdev->irq, netdev); + if (adapter->flags & IXGBE_FLAG_MSIX_ENABLED) { + int num_q_vectors = adapter->num_msix_vectors - NON_Q_VECTORS; + for (i = 0; i < num_q_vectors; i++) { + struct ixgbe_q_vector *q_vector = adapter->q_vector[i]; + ixgbe_msix_clean_many(0, q_vector); + } + } else { + ixgbe_intr(adapter->pdev->irq, netdev); + } adapter->flags &= ~IXGBE_FLAG_IN_NETPOLL; - enable_irq(adapter->pdev->irq); } #endif -- GitLab From 0c19d6af9253f19b41821c29b9c49c2214f19425 Mon Sep 17 00:00:00 2001 From: Peter P Waskiewicz Jr Date: Thu, 30 Jul 2009 12:25:28 +0000 Subject: [PATCH 0622/1342] ixgbe: Fix usage of second flags bitmap when using LRO/RSC A second set of feature flag bits was added, and the hardware RSC engine flags were moved there. However, the code itself didn't make the move completely to use the new bitmap. Signed-off-by: Peter P Waskiewicz Jr Acked-by: Mallikarjuna R Chilakala Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_ethtool.c | 6 +++--- drivers/net/ixgbe/ixgbe_main.c | 12 ++++++------ 2 files changed, 9 insertions(+), 9 deletions(-) diff --git a/drivers/net/ixgbe/ixgbe_ethtool.c b/drivers/net/ixgbe/ixgbe_ethtool.c index 2a978008fd6..7ddb50c03f0 100644 --- a/drivers/net/ixgbe/ixgbe_ethtool.c +++ b/drivers/net/ixgbe/ixgbe_ethtool.c @@ -1999,13 +1999,13 @@ static int ixgbe_set_flags(struct net_device *netdev, u32 data) ethtool_op_set_flags(netdev, data); - if (!(adapter->flags & IXGBE_FLAG2_RSC_CAPABLE)) + if (!(adapter->flags2 & IXGBE_FLAG2_RSC_CAPABLE)) return 0; /* if state changes we need to update adapter->flags and reset */ if ((!!(data & ETH_FLAG_LRO)) != - (!!(adapter->flags & IXGBE_FLAG2_RSC_ENABLED))) { - adapter->flags ^= IXGBE_FLAG2_RSC_ENABLED; + (!!(adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED))) { + adapter->flags2 ^= IXGBE_FLAG2_RSC_ENABLED; if (netif_running(netdev)) ixgbe_reinit_locked(adapter); else diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index 60c4a8bf7d3..110c65ab5cb 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -780,7 +780,7 @@ static bool ixgbe_clean_rx_irq(struct ixgbe_q_vector *q_vector, prefetch(next_rxd); cleaned_count++; - if (adapter->flags & IXGBE_FLAG2_RSC_CAPABLE) + if (adapter->flags2 & IXGBE_FLAG2_RSC_CAPABLE) rsc_count = ixgbe_get_rsc_count(rx_desc); if (rsc_count) { @@ -2036,7 +2036,7 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) IXGBE_WRITE_REG(hw, IXGBE_PSRTYPE(0), psrtype); } } else { - if (!(adapter->flags & IXGBE_FLAG2_RSC_ENABLED) && + if (!(adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED) && (netdev->mtu <= ETH_DATA_LEN)) rx_buf_len = MAXIMUM_ETHERNET_VLAN_SIZE; else @@ -2165,7 +2165,7 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) IXGBE_WRITE_REG(hw, IXGBE_RDRXCTL, rdrxctl); } - if (adapter->flags & IXGBE_FLAG2_RSC_ENABLED) { + if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED) { /* Enable 82599 HW-RSC */ for (i = 0; i < adapter->num_rx_queues; i++) { j = adapter->rx_ring[i].reg_idx; @@ -3812,8 +3812,8 @@ static int __devinit ixgbe_sw_init(struct ixgbe_adapter *adapter) adapter->max_msix_q_vectors = MAX_MSIX_Q_VECTORS_82598; } else if (hw->mac.type == ixgbe_mac_82599EB) { adapter->max_msix_q_vectors = MAX_MSIX_Q_VECTORS_82599; - adapter->flags |= IXGBE_FLAG2_RSC_CAPABLE; - adapter->flags |= IXGBE_FLAG2_RSC_ENABLED; + adapter->flags2 |= IXGBE_FLAG2_RSC_CAPABLE; + adapter->flags2 |= IXGBE_FLAG2_RSC_ENABLED; adapter->flags |= IXGBE_FLAG_FDIR_HASH_CAPABLE; adapter->ring_feature[RING_F_FDIR].indices = IXGBE_MAX_FDIR_INDICES; @@ -5618,7 +5618,7 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev, if (pci_using_dac) netdev->features |= NETIF_F_HIGHDMA; - if (adapter->flags & IXGBE_FLAG2_RSC_ENABLED) + if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED) netdev->features |= NETIF_F_LRO; /* make sure the EEPROM is good */ -- GitLab From 0a924578bc4a2823a95c151f56975c71f5c156bb Mon Sep 17 00:00:00 2001 From: Peter P Waskiewicz Jr Date: Thu, 30 Jul 2009 12:26:00 +0000 Subject: [PATCH 0623/1342] ixgbe: Fix RSC completion delay causing Rx interrupts to stop When a user disables interrupt throttling with ethtool on 82599 devices, the interrupt timer may not be re-enabled if hardware RSC is running. The RSC completions in hardware don't complete before the next ITR event tries to fire, so the ITR timer never gets re-armed. This patch increases the amount of time between interrupts when throttling is disabled (rx-usecs = 0) when the hardware RSC deature is enabled. Signed-off-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe.h | 2 ++ drivers/net/ixgbe/ixgbe_ethtool.c | 5 ++++- 2 files changed, 6 insertions(+), 1 deletion(-) diff --git a/drivers/net/ixgbe/ixgbe.h b/drivers/net/ixgbe/ixgbe.h index 1b12c7ba275..e11d83d5852 100644 --- a/drivers/net/ixgbe/ixgbe.h +++ b/drivers/net/ixgbe/ixgbe.h @@ -96,6 +96,8 @@ #define IXGBE_TX_FLAGS_VLAN_PRIO_MASK 0x0000e000 #define IXGBE_TX_FLAGS_VLAN_SHIFT 16 +#define IXGBE_MAX_RSC_INT_RATE 162760 + /* wrapper around a pointer to a socket buffer, * so a DMA handle can be stored along with the buffer */ struct ixgbe_tx_buffer { diff --git a/drivers/net/ixgbe/ixgbe_ethtool.c b/drivers/net/ixgbe/ixgbe_ethtool.c index 7ddb50c03f0..79144e950a3 100644 --- a/drivers/net/ixgbe/ixgbe_ethtool.c +++ b/drivers/net/ixgbe/ixgbe_ethtool.c @@ -1975,7 +1975,10 @@ static int ixgbe_set_coalesce(struct net_device *netdev, * any other value means disable eitr, which is best * served by setting the interrupt rate very high */ - adapter->eitr_param = IXGBE_MAX_INT_RATE; + if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED) + adapter->eitr_param = IXGBE_MAX_RSC_INT_RATE; + else + adapter->eitr_param = IXGBE_MAX_INT_RATE; adapter->itr_setting = 0; } -- GitLab From 95fc17aac45300f45968aacd97a536ddd8db8101 Mon Sep 17 00:00:00 2001 From: Dan Williams Date: Fri, 31 Jul 2009 12:39:15 +1000 Subject: [PATCH 0624/1342] md/raid6: release spare page at ->stop() Add missing call to safe_put_page from stop() by unifying open coded raid5_conf_t de-allocation under free_conf(). Cc: Signed-off-by: Dan Williams Signed-off-by: NeilBrown --- drivers/md/raid5.c | 26 ++++++++++++-------------- 1 file changed, 12 insertions(+), 14 deletions(-) diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c index 37835538b58..39374230a46 100644 --- a/drivers/md/raid5.c +++ b/drivers/md/raid5.c @@ -4316,6 +4316,15 @@ raid5_size(mddev_t *mddev, sector_t sectors, int raid_disks) return sectors * (raid_disks - conf->max_degraded); } +static void free_conf(raid5_conf_t *conf) +{ + shrink_stripes(conf); + safe_put_page(conf->spare_page); + kfree(conf->disks); + kfree(conf->stripe_hashtbl); + kfree(conf); +} + static raid5_conf_t *setup_conf(mddev_t *mddev) { raid5_conf_t *conf; @@ -4447,11 +4456,7 @@ static raid5_conf_t *setup_conf(mddev_t *mddev) abort: if (conf) { - shrink_stripes(conf); - safe_put_page(conf->spare_page); - kfree(conf->disks); - kfree(conf->stripe_hashtbl); - kfree(conf); + free_conf(conf); return ERR_PTR(-EIO); } else return ERR_PTR(-ENOMEM); @@ -4629,12 +4634,8 @@ abort: md_unregister_thread(mddev->thread); mddev->thread = NULL; if (conf) { - shrink_stripes(conf); print_raid5_conf(conf); - safe_put_page(conf->spare_page); - kfree(conf->disks); - kfree(conf->stripe_hashtbl); - kfree(conf); + free_conf(conf); } mddev->private = NULL; printk(KERN_ALERT "raid5: failed to run raid set %s\n", mdname(mddev)); @@ -4649,13 +4650,10 @@ static int stop(mddev_t *mddev) md_unregister_thread(mddev->thread); mddev->thread = NULL; - shrink_stripes(conf); - kfree(conf->stripe_hashtbl); mddev->queue->backing_dev_info.congested_fn = NULL; blk_sync_queue(mddev->queue); /* the unplug fn references 'conf'*/ sysfs_remove_group(&mddev->kobj, &raid5_attrs_group); - kfree(conf->disks); - kfree(conf); + free_conf(conf); mddev->private = NULL; return 0; } -- GitLab From 97db39a1f6f69e906e98118392400de5217aa33a Mon Sep 17 00:00:00 2001 From: Eric Sandeen Date: Sun, 26 Jul 2009 21:52:01 -0500 Subject: [PATCH 0625/1342] xfs: reduce bmv_count in xfs_vn_fiemap commit 6321e3ed2acf3ee9643cdd403e1c88605d7944ba caused the full bmv_count's worth of getbmapx structures to get allocated; telling it to do MAXEXTNUM was a bit insane, resulting in ENOMEM every time. Chop it down to something reasonable, the number of slots in the caller's input buffer. If this is too large the caller may get ENOMEM but the reason should not be a mystery, and they can try again with something smaller. We add 1 to the value because in the normal getbmap world, bmv_count includes the header and xfs_getbmap does: nex = bmv->bmv_count - 1; if (nex <= 0) return XFS_ERROR(EINVAL); Signed-off-by: Eric Sandeen Reviewed-by: Olaf Weber Reviewed-by: Christoph Hellwig Signed-off-by: Felix Blyakher --- fs/xfs/linux-2.6/xfs_iops.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_iops.c b/fs/xfs/linux-2.6/xfs_iops.c index 58973bb4603..8070b34cc28 100644 --- a/fs/xfs/linux-2.6/xfs_iops.c +++ b/fs/xfs/linux-2.6/xfs_iops.c @@ -680,8 +680,8 @@ xfs_vn_fiemap( else bm.bmv_length = BTOBB(length); - /* our formatter will tell xfs_getbmap when to stop. */ - bm.bmv_count = MAXEXTNUM; + /* We add one because in getbmap world count includes the header */ + bm.bmv_count = fieinfo->fi_extents_max + 1; bm.bmv_iflags = BMV_IF_PREALLOC; if (fieinfo->fi_flags & FIEMAP_FLAG_XATTR) bm.bmv_iflags |= BMV_IF_ATTRFORK; -- GitLab From c8a4051c3731b6db224482218cfd535ab9393ff8 Mon Sep 17 00:00:00 2001 From: Eric Sandeen Date: Fri, 31 Jul 2009 00:02:17 -0500 Subject: [PATCH 0626/1342] xfs: bump up nr_to_write in xfs_vm_writepage VM calculation for nr_to_write seems off. Bump it way up, this gets simple streaming writes zippy again. To be reviewed again after Jens' writeback changes. Signed-off-by: Christoph Hellwig Signed-off-by: Eric Sandeen Cc: Chris Mason Reviewed-by: Felix Blyakher Signed-off-by: Felix Blyakher --- fs/xfs/linux-2.6/xfs_aops.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/fs/xfs/linux-2.6/xfs_aops.c b/fs/xfs/linux-2.6/xfs_aops.c index 7ec89fc05b2..aecf2519db7 100644 --- a/fs/xfs/linux-2.6/xfs_aops.c +++ b/fs/xfs/linux-2.6/xfs_aops.c @@ -1268,6 +1268,14 @@ xfs_vm_writepage( if (!page_has_buffers(page)) create_empty_buffers(page, 1 << inode->i_blkbits, 0); + + /* + * VM calculation for nr_to_write seems off. Bump it way + * up, this gets simple streaming writes zippy again. + * To be reviewed again after Jens' writeback changes. + */ + wbc->nr_to_write *= 4; + /* * Convert delayed allocate, unwritten or unmapped space * to real space and flush out to disk. -- GitLab From cbb4f2646d77b536ed2b1500ef6641083228ed8f Mon Sep 17 00:00:00 2001 From: Li Zefan Date: Fri, 31 Jul 2009 08:55:48 +0200 Subject: [PATCH 0627/1342] io context: fix ref counting Commit d9c7d394a8ebacb60097b192939ae9f15235225e ("block: prevent possible io_context->refcount overflow") mistakenly changed atomic_inc(&ioc->nr_tasks) to atomic_long_inc(&ioc->refcount). Signed-off-by: Li Zefan Acked-by: Nikanth Karthikesan Signed-off-by: Jens Axboe --- include/linux/iocontext.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/linux/iocontext.h b/include/linux/iocontext.h index dd05434fa45..4da4a75c3f1 100644 --- a/include/linux/iocontext.h +++ b/include/linux/iocontext.h @@ -92,7 +92,7 @@ static inline struct io_context *ioc_task_link(struct io_context *ioc) * a race). */ if (ioc && atomic_long_inc_not_zero(&ioc->refcount)) { - atomic_long_inc(&ioc->refcount); + atomic_inc(&ioc->nr_tasks); return ioc; } -- GitLab From aa563af763373a7e67a7b8fdb427d2a2fcbeab3b Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Fri, 31 Jul 2009 10:05:11 +0200 Subject: [PATCH 0628/1342] ALSA: hda - Increase PCM stream name buf in patch_realtek.c The name buf with size 16 is too short for some codec names, e.g. truncated like "ALC861-VD Analo". Now the size is doubled. Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_realtek.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 8c8b273116f..b95df5d5dcc 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -275,13 +275,13 @@ struct alc_spec { */ unsigned int num_init_verbs; - char stream_name_analog[16]; /* analog PCM stream */ + char stream_name_analog[32]; /* analog PCM stream */ struct hda_pcm_stream *stream_analog_playback; struct hda_pcm_stream *stream_analog_capture; struct hda_pcm_stream *stream_analog_alt_playback; struct hda_pcm_stream *stream_analog_alt_capture; - char stream_name_digital[16]; /* digital PCM stream */ + char stream_name_digital[32]; /* digital PCM stream */ struct hda_pcm_stream *stream_digital_playback; struct hda_pcm_stream *stream_digital_capture; -- GitLab From f065fabc864f4c98857bf67caa2365e9f8545751 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Fri, 31 Jul 2009 08:32:03 +0200 Subject: [PATCH 0629/1342] ALSA: sound/aoa: Add kmalloc NULL tests Check that the result of kzalloc is not NULL before a dereference. The semantic match that finds this problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // @@ expression *x; identifier f; constant char *C; @@ x = \(kmalloc\|kcalloc\|kzalloc\)(...); ... when != x == NULL when != x != NULL when != (x || ...) ( kfree(x) | f(...,C,...,x,...) | *f(...,x,...) | *x->f ) // Signed-off-by: Julia Lawall Signed-off-by: Takashi Iwai --- sound/aoa/core/gpio-pmf.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/sound/aoa/core/gpio-pmf.c b/sound/aoa/core/gpio-pmf.c index 5ca2220eac7..1dd0c28d1fb 100644 --- a/sound/aoa/core/gpio-pmf.c +++ b/sound/aoa/core/gpio-pmf.c @@ -182,6 +182,10 @@ static int pmf_set_notify(struct gpio_runtime *rt, if (!old && notify) { irq_client = kzalloc(sizeof(struct pmf_irq_client), GFP_KERNEL); + if (!irq_client) { + err = -ENOMEM; + goto out_unlock; + } irq_client->data = notif; irq_client->handler = pmf_handle_notify_irq; irq_client->owner = THIS_MODULE; -- GitLab From 6de7e356faf54aa75de5b624bbce28a5b776dfa8 Mon Sep 17 00:00:00 2001 From: Sebastian Andrzej Siewior Date: Thu, 18 Jun 2009 10:19:12 +0200 Subject: [PATCH 0630/1342] lib/scatterlist: add a flags to signalize mapping direction sg_miter_start() is currently unaware of the direction of the copy process (to or from the scatter list). It is important to know the direction because the page has to be flushed in case the data written is seen on a different mapping in user land on cache incoherent architectures. Signed-off-by: Sebastian Andrzej Siewior Acked-by: FUJITA Tomonori Acked-by: Tejun Heo Signed-off-by: Pierre Ossman --- include/linux/scatterlist.h | 2 ++ lib/scatterlist.c | 16 ++++++++++++---- 2 files changed, 14 insertions(+), 4 deletions(-) diff --git a/include/linux/scatterlist.h b/include/linux/scatterlist.h index e5996984ddd..9aaf5bfdad1 100644 --- a/include/linux/scatterlist.h +++ b/include/linux/scatterlist.h @@ -242,6 +242,8 @@ size_t sg_copy_to_buffer(struct scatterlist *sgl, unsigned int nents, */ #define SG_MITER_ATOMIC (1 << 0) /* use kmap_atomic */ +#define SG_MITER_TO_SG (1 << 1) /* flush back to phys on unmap */ +#define SG_MITER_FROM_SG (1 << 2) /* nop */ struct sg_mapping_iter { /* the following three fields can be accessed directly */ diff --git a/lib/scatterlist.c b/lib/scatterlist.c index a295e404e90..0d475d8167b 100644 --- a/lib/scatterlist.c +++ b/lib/scatterlist.c @@ -314,6 +314,7 @@ void sg_miter_start(struct sg_mapping_iter *miter, struct scatterlist *sgl, miter->__sg = sgl; miter->__nents = nents; miter->__offset = 0; + WARN_ON(!(flags & (SG_MITER_TO_SG | SG_MITER_FROM_SG))); miter->__flags = flags; } EXPORT_SYMBOL(sg_miter_start); @@ -394,6 +395,9 @@ void sg_miter_stop(struct sg_mapping_iter *miter) if (miter->addr) { miter->__offset += miter->consumed; + if (miter->__flags & SG_MITER_TO_SG) + flush_kernel_dcache_page(miter->page); + if (miter->__flags & SG_MITER_ATOMIC) { WARN_ON(!irqs_disabled()); kunmap_atomic(miter->addr, KM_BIO_SRC_IRQ); @@ -426,8 +430,14 @@ static size_t sg_copy_buffer(struct scatterlist *sgl, unsigned int nents, unsigned int offset = 0; struct sg_mapping_iter miter; unsigned long flags; + unsigned int sg_flags = SG_MITER_ATOMIC; + + if (to_buffer) + sg_flags |= SG_MITER_FROM_SG; + else + sg_flags |= SG_MITER_TO_SG; - sg_miter_start(&miter, sgl, nents, SG_MITER_ATOMIC); + sg_miter_start(&miter, sgl, nents, sg_flags); local_irq_save(flags); @@ -438,10 +448,8 @@ static size_t sg_copy_buffer(struct scatterlist *sgl, unsigned int nents, if (to_buffer) memcpy(buf + offset, miter.addr, len); - else { + else memcpy(miter.addr, buf + offset, len); - flush_kernel_dcache_page(miter.page); - } offset += len; } -- GitLab From da60a91d012bcb10bc5bcd86d585c4281742832c Mon Sep 17 00:00:00 2001 From: Sebastian Andrzej Siewior Date: Thu, 18 Jun 2009 09:33:32 +0200 Subject: [PATCH 0631/1342] sdhci: use SG_MITER_TO_SG/SG_MITER_FROM_SG so the page will be flushed on unmap on ARCH which need it. Signed-off-by: Sebastian Andrzej Siewior Signed-off-by: Pierre Ossman --- drivers/mmc/host/sdhci.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index 62041c7e924..fc96f8cb9c0 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -773,8 +773,14 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data) } if (!(host->flags & SDHCI_REQ_USE_DMA)) { - sg_miter_start(&host->sg_miter, - data->sg, data->sg_len, SG_MITER_ATOMIC); + int flags; + + flags = SG_MITER_ATOMIC; + if (host->data->flags & MMC_DATA_READ) + flags |= SG_MITER_TO_SG; + else + flags |= SG_MITER_FROM_SG; + sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags); host->blocks = data->blocks; } -- GitLab From 4b2a108cd0d34880fe9d932258ca5b2ccebcd05e Mon Sep 17 00:00:00 2001 From: Sebastian Andrzej Siewior Date: Mon, 22 Jun 2009 09:18:05 +0200 Subject: [PATCH 0632/1342] cb710: use SG_MITER_TO_SG/SG_MITER_FROM_SG MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit the code allready uses flush_kernel_dcache_page(). This patch updates the driver to the recent sg API changes which require that either SG_MITER_TO_SG or SG_MITER_FROM_SG is set. SG_MITER_TO_SG calls flush_kernel_dcache_page() in sg_mitter_stop() Signed-off-by: Sebastian Andrzej Siewior Acked-by: MichaÅ‚ MirosÅ‚aw Signed-off-by: Pierre Ossman --- drivers/misc/cb710/sgbuf2.c | 4 ---- drivers/mmc/host/cb710-mmc.c | 6 +++--- include/linux/cb710.h | 29 +++-------------------------- 3 files changed, 6 insertions(+), 33 deletions(-) diff --git a/drivers/misc/cb710/sgbuf2.c b/drivers/misc/cb710/sgbuf2.c index d38a7acdb6e..d019746551f 100644 --- a/drivers/misc/cb710/sgbuf2.c +++ b/drivers/misc/cb710/sgbuf2.c @@ -114,7 +114,6 @@ static void sg_dwiter_write_slow(struct sg_mapping_iter *miter, uint32_t data) if (!left) return; addr += len; - flush_kernel_dcache_page(miter->page); } while (sg_dwiter_next(miter)); } @@ -142,9 +141,6 @@ void cb710_sg_dwiter_write_next_block(struct sg_mapping_iter *miter, uint32_t da return; } else sg_dwiter_write_slow(miter, data); - - if (miter->length == miter->consumed) - flush_kernel_dcache_page(miter->page); } EXPORT_SYMBOL_GPL(cb710_sg_dwiter_write_next_block); diff --git a/drivers/mmc/host/cb710-mmc.c b/drivers/mmc/host/cb710-mmc.c index 11efefb1af5..4e72964a7b4 100644 --- a/drivers/mmc/host/cb710-mmc.c +++ b/drivers/mmc/host/cb710-mmc.c @@ -278,7 +278,7 @@ static int cb710_mmc_receive(struct cb710_slot *slot, struct mmc_data *data) if (unlikely(data->blksz & 15 && (data->blocks != 1 || data->blksz != 8))) return -EINVAL; - sg_miter_start(&miter, data->sg, data->sg_len, 0); + sg_miter_start(&miter, data->sg, data->sg_len, SG_MITER_TO_SG); cb710_modify_port_8(slot, CB710_MMC_CONFIG2_PORT, 15, CB710_MMC_C2_READ_PIO_SIZE_MASK); @@ -307,7 +307,7 @@ static int cb710_mmc_receive(struct cb710_slot *slot, struct mmc_data *data) goto out; } out: - cb710_sg_miter_stop_writing(&miter); + sg_miter_stop(&miter); return err; } @@ -322,7 +322,7 @@ static int cb710_mmc_send(struct cb710_slot *slot, struct mmc_data *data) if (unlikely(data->blocks > 1 && data->blksz & 15)) return -EINVAL; - sg_miter_start(&miter, data->sg, data->sg_len, 0); + sg_miter_start(&miter, data->sg, data->sg_len, SG_MITER_FROM_SG); cb710_modify_port_8(slot, CB710_MMC_CONFIG2_PORT, 0, CB710_MMC_C2_READ_PIO_SIZE_MASK); diff --git a/include/linux/cb710.h b/include/linux/cb710.h index 63bc9a4d292..8cc10411bab 100644 --- a/include/linux/cb710.h +++ b/include/linux/cb710.h @@ -140,29 +140,6 @@ void cb710_dump_regs(struct cb710_chip *chip, unsigned dump); #include #include -/** - * cb710_sg_miter_stop_writing - stop mapping iteration after writing - * @miter: sg mapping iter to be stopped - * - * Description: - * Stops mapping iterator @miter. @miter should have been started - * started using sg_miter_start(). A stopped iteration can be - * resumed by calling sg_miter_next() on it. This is useful when - * resources (kmap) need to be released during iteration. - * - * This is a convenience wrapper that will be optimized out for arches - * that don't need flush_kernel_dcache_page(). - * - * Context: - * IRQ disabled if the SG_MITER_ATOMIC is set. Don't care otherwise. - */ -static inline void cb710_sg_miter_stop_writing(struct sg_mapping_iter *miter) -{ - if (miter->page) - flush_kernel_dcache_page(miter->page); - sg_miter_stop(miter); -} - /* * 32-bit PIO mapping sg iterator * @@ -171,12 +148,12 @@ static inline void cb710_sg_miter_stop_writing(struct sg_mapping_iter *miter) * without DMA support). * * Best-case reading (transfer from device): - * sg_miter_start(); + * sg_miter_start(, SG_MITER_TO_SG); * cb710_sg_dwiter_write_from_io(); - * cb710_sg_miter_stop_writing(); + * sg_miter_stop(); * * Best-case writing (transfer to device): - * sg_miter_start(); + * sg_miter_start(, SG_MITER_FROM_SG); * cb710_sg_dwiter_read_to_io(); * sg_miter_stop(); */ -- GitLab From a9239d750d9991f2feee78fc5669a4613abc1adb Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Sun, 28 Jun 2009 09:26:31 -0700 Subject: [PATCH 0633/1342] imxmmc: Remove unnecessary semicolons Signed-off-by: Joe Perches Acked-by: Pavel Pisa Signed-off-by: Pierre Ossman --- drivers/mmc/host/imxmmc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/mmc/host/imxmmc.c b/drivers/mmc/host/imxmmc.c index e0be21a4a69..bf98d7cc928 100644 --- a/drivers/mmc/host/imxmmc.c +++ b/drivers/mmc/host/imxmmc.c @@ -652,7 +652,7 @@ static irqreturn_t imxmci_irq(int irq, void *devid) set_bit(IMXMCI_PEND_STARTED_b, &host->pending_events); tasklet_schedule(&host->tasklet); - return IRQ_RETVAL(handled);; + return IRQ_RETVAL(handled); } static void imxmci_tasklet_fnc(unsigned long data) -- GitLab From 3822a0e38c329a598cb6f5baa16be7504e0db8d9 Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Fri, 31 Jul 2009 12:27:28 +0200 Subject: [PATCH 0634/1342] mmc: orphan subsystem I do not have the time to take care of this, so remove myself as maintainer. Signed-off-by: Pierre Ossman --- MAINTAINERS | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index 79471ba4981..d6befb2c470 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -3420,8 +3420,7 @@ S: Supported F: drivers/mfd/ MULTIMEDIA CARD (MMC), SECURE DIGITAL (SD) AND SDIO SUBSYSTEM -M: Pierre Ossman -S: Maintained +S: Orphan F: drivers/mmc/ F: include/linux/mmc/ -- GitLab From c7121843685de2bf7f3afd3ae1d6a146010bf1fc Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Tue, 28 Jul 2009 14:09:55 -0700 Subject: [PATCH 0635/1342] clocksource: Save mult_orig in clocksource_disable() To fix the common case where ->enable() does not set up mult, make sure mult_orig is saved in mult on disable. Also add comments to explain why we do this. Signed-off-by: Magnus Damm Cc: johnstul@us.ibm.com Cc: lethal@linux-sh.org Cc: akpm@linux-foundation.org LKML-Reference: <20090618152432.10136.9932.sendpatchset@rx1.opensource.se> Signed-off-by: Thomas Gleixner --- include/linux/clocksource.h | 14 +++++++++++++- 1 file changed, 13 insertions(+), 1 deletion(-) diff --git a/include/linux/clocksource.h b/include/linux/clocksource.h index c56457c8334..1219be4fb42 100644 --- a/include/linux/clocksource.h +++ b/include/linux/clocksource.h @@ -293,7 +293,12 @@ static inline int clocksource_enable(struct clocksource *cs) if (cs->enable) ret = cs->enable(cs); - /* save mult_orig on enable */ + /* + * The frequency may have changed while the clocksource + * was disabled. If so the code in ->enable() must update + * the mult value to reflect the new frequency. Make sure + * mult_orig follows this change. + */ cs->mult_orig = cs->mult; return ret; @@ -309,6 +314,13 @@ static inline int clocksource_enable(struct clocksource *cs) */ static inline void clocksource_disable(struct clocksource *cs) { + /* + * Save mult_orig in mult so clocksource_enable() can + * restore the value regardless if ->enable() updates + * the value of mult or not. + */ + cs->mult = cs->mult_orig; + if (cs->disable) cs->disable(cs); } -- GitLab From ff46a474ca2566d79e8d7454442b56d82bce37c1 Mon Sep 17 00:00:00 2001 From: Guennadi Liakhovetski Date: Fri, 31 Jul 2009 15:42:09 +0200 Subject: [PATCH 0636/1342] mx3: Fix double pin allocation in pcm037_eet.c SPI pins are now allocated in pcm037.c, remove them from EET. Signed-off-by: Guennadi Liakhovetski Signed-off-by: Sascha Hauer --- arch/arm/mach-mx3/pcm037_eet.c | 9 --------- 1 file changed, 9 deletions(-) diff --git a/arch/arm/mach-mx3/pcm037_eet.c b/arch/arm/mach-mx3/pcm037_eet.c index fe52fb1bb8b..8d386000fc4 100644 --- a/arch/arm/mach-mx3/pcm037_eet.c +++ b/arch/arm/mach-mx3/pcm037_eet.c @@ -24,15 +24,6 @@ #include "devices.h" static unsigned int pcm037_eet_pins[] = { - /* SPI #1 */ - MX31_PIN_CSPI1_MISO__MISO, - MX31_PIN_CSPI1_MOSI__MOSI, - MX31_PIN_CSPI1_SCLK__SCLK, - MX31_PIN_CSPI1_SPI_RDY__SPI_RDY, - MX31_PIN_CSPI1_SS0__SS0, - MX31_PIN_CSPI1_SS1__SS1, - MX31_PIN_CSPI1_SS2__SS2, - /* Reserve and hardwire GPIO 57 high - S6E63D6 chipselect */ IOMUX_MODE(MX31_PIN_KEY_COL7, IOMUX_CONFIG_GPIO), /* GPIO keys */ -- GitLab From 6606bb97e146a387932efee263745b7240a11193 Mon Sep 17 00:00:00 2001 From: Josef Bacik Date: Fri, 31 Jul 2009 11:03:58 -0400 Subject: [PATCH 0637/1342] Btrfs: fix btrfs_remove_from_free_space corner case Yan Zheng hit a problem where we tried to remove some free space but failed because we couldn't find the free space entry. This is because the free space was held within a bitmap that had a starting offset well before the actual offset of the free space, and there were free space extents that were in the same range as that offset, so tree_search_offset returned with NULL because we couldn't find a free space extent that had that offset. This is fixed by making sure that if we fail to find the entry, we re-search again with bitmap_only set to 1 and do an offset_to_bitmap so we can get the appropriate bitmap. A similar problem happens in btrfs_alloc_from_bitmap for the clustering code, but that is not as bad since we will just go and redo our cluster allocation. Also this adds some debugging checks to make sure that the free space we are trying to remove from the bitmap is in fact there. This can probably go away after a while, but since this code is only used by the tree-logging stuff it would be nice to run with it for a while to make sure there are no problems. Signed-off-by: Josef Bacik Signed-off-by: Chris Mason --- fs/btrfs/free-space-cache.c | 73 ++++++++++++++++++++++++++++++++----- 1 file changed, 64 insertions(+), 9 deletions(-) diff --git a/fs/btrfs/free-space-cache.c b/fs/btrfs/free-space-cache.c index af99b78b288..5edcee3a617 100644 --- a/fs/btrfs/free-space-cache.c +++ b/fs/btrfs/free-space-cache.c @@ -414,11 +414,29 @@ static noinline int remove_from_bitmap(struct btrfs_block_group_cache *block_gro u64 *offset, u64 *bytes) { u64 end; + u64 search_start, search_bytes; + int ret; again: end = bitmap_info->offset + (u64)(BITS_PER_BITMAP * block_group->sectorsize) - 1; + /* + * XXX - this can go away after a few releases. + * + * since the only user of btrfs_remove_free_space is the tree logging + * stuff, and the only way to test that is under crash conditions, we + * want to have this debug stuff here just in case somethings not + * working. Search the bitmap for the space we are trying to use to + * make sure its actually there. If its not there then we need to stop + * because something has gone wrong. + */ + search_start = *offset; + search_bytes = *bytes; + ret = search_bitmap(block_group, bitmap_info, &search_start, + &search_bytes); + BUG_ON(ret < 0 || search_start != *offset); + if (*offset > bitmap_info->offset && *offset + *bytes > end) { bitmap_clear_bits(block_group, bitmap_info, *offset, end - *offset + 1); @@ -430,6 +448,7 @@ again: } if (*bytes) { + struct rb_node *next = rb_next(&bitmap_info->offset_index); if (!bitmap_info->bytes) { unlink_free_space(block_group, bitmap_info); kfree(bitmap_info->bitmap); @@ -438,16 +457,36 @@ again: recalculate_thresholds(block_group); } - bitmap_info = tree_search_offset(block_group, - offset_to_bitmap(block_group, - *offset), - 1, 0); - if (!bitmap_info) + /* + * no entry after this bitmap, but we still have bytes to + * remove, so something has gone wrong. + */ + if (!next) return -EINVAL; + bitmap_info = rb_entry(next, struct btrfs_free_space, + offset_index); + + /* + * if the next entry isn't a bitmap we need to return to let the + * extent stuff do its work. + */ if (!bitmap_info->bitmap) return -EAGAIN; + /* + * Ok the next item is a bitmap, but it may not actually hold + * the information for the rest of this free space stuff, so + * look for it, and if we don't find it return so we can try + * everything over again. + */ + search_start = *offset; + search_bytes = *bytes; + ret = search_bitmap(block_group, bitmap_info, &search_start, + &search_bytes); + if (ret < 0 || search_start != *offset) + return -EAGAIN; + goto again; } else if (!bitmap_info->bytes) { unlink_free_space(block_group, bitmap_info); @@ -644,8 +683,17 @@ int btrfs_remove_free_space(struct btrfs_block_group_cache *block_group, again: info = tree_search_offset(block_group, offset, 0, 0); if (!info) { - WARN_ON(1); - goto out_lock; + /* + * oops didn't find an extent that matched the space we wanted + * to remove, look for a bitmap instead + */ + info = tree_search_offset(block_group, + offset_to_bitmap(block_group, offset), + 1, 0); + if (!info) { + WARN_ON(1); + goto out_lock; + } } if (info->bytes < bytes && rb_next(&info->offset_index)) { @@ -957,8 +1005,15 @@ static u64 btrfs_alloc_from_bitmap(struct btrfs_block_group_cache *block_group, if (cluster->block_group != block_group) goto out; - entry = tree_search_offset(block_group, search_start, 0, 0); - + /* + * search_start is the beginning of the bitmap, but at some point it may + * be a good idea to point to the actual start of the free area in the + * bitmap, so do the offset_to_bitmap trick anyway, and set bitmap_only + * to 1 to make sure we get the bitmap entry + */ + entry = tree_search_offset(block_group, + offset_to_bitmap(block_group, search_start), + 1, 0); if (!entry || !entry->bitmap) goto out; -- GitLab From 013f1b12f4fc479f697acae2f31bad220162cd03 Mon Sep 17 00:00:00 2001 From: Chris Mason Date: Fri, 31 Jul 2009 14:57:55 -0400 Subject: [PATCH 0638/1342] Btrfs: make sure the async caching thread advances the key The async caching thread can end up looping forever if a given search puts it at the last key in a leaf. It will end up calling btrfs_next_leaf and then checking if it needs to politely drop the read semaphore. Most of the time this looping isn't noticed because it is able to make progress the next time around. But, during log replay, we wait on the async caching thread to finish, and the async thread is waiting on the commit, and no progress is really made. The fix used here is to copy the key out of the next leaf, that way our search lands there properly. Signed-off-by: Chris Mason --- fs/btrfs/extent-tree.c | 21 +++++++++++++++++---- 1 file changed, 17 insertions(+), 4 deletions(-) diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c index dc84daee6bc..72a2b9c28e9 100644 --- a/fs/btrfs/extent-tree.c +++ b/fs/btrfs/extent-tree.c @@ -265,10 +265,6 @@ static int caching_kthread(void *data) atomic_inc(&block_group->space_info->caching_threads); last = max_t(u64, block_group->key.objectid, BTRFS_SUPER_INFO_OFFSET); -again: - /* need to make sure the commit_root doesn't disappear */ - down_read(&fs_info->extent_commit_sem); - /* * We don't want to deadlock with somebody trying to allocate a new * extent for the extent root while also trying to search the extent @@ -282,6 +278,10 @@ again: key.objectid = last; key.offset = 0; btrfs_set_key_type(&key, BTRFS_EXTENT_ITEM_KEY); +again: + /* need to make sure the commit_root doesn't disappear */ + down_read(&fs_info->extent_commit_sem); + ret = btrfs_search_slot(NULL, fs_info->extent_root, &key, path, 0, 0); if (ret < 0) goto err; @@ -304,6 +304,19 @@ again: if (need_resched() || btrfs_transaction_in_commit(fs_info)) { + leaf = path->nodes[0]; + + /* this shouldn't happen, but if the + * leaf is empty just move on. + */ + if (btrfs_header_nritems(leaf) == 0) + break; + /* + * we need to copy the key out so that + * we are sure the next search advances + * us forward in the btree. + */ + btrfs_item_key_to_cpu(leaf, &key, 0); btrfs_release_path(fs_info->extent_root, path); up_read(&fs_info->extent_commit_sem); schedule_timeout(1); -- GitLab From ab57a40827d99e2d8e59066a56b93bf6c844c916 Mon Sep 17 00:00:00 2001 From: Goldwyn Rodrigues Date: Fri, 31 Jul 2009 14:28:02 -0500 Subject: [PATCH 0639/1342] ocfs2: Remove redundant BUG_ON in __dlm_queue_ast() We BUG_ON() the same thing twice. Signed-off-by: Goldwyn Rodrigues Signed-off-by: Joel Becker --- fs/ocfs2/dlm/dlmast.c | 1 - 1 file changed, 1 deletion(-) diff --git a/fs/ocfs2/dlm/dlmast.c b/fs/ocfs2/dlm/dlmast.c index d07ddbe4b28..81eff8e5832 100644 --- a/fs/ocfs2/dlm/dlmast.c +++ b/fs/ocfs2/dlm/dlmast.c @@ -103,7 +103,6 @@ static void __dlm_queue_ast(struct dlm_ctxt *dlm, struct dlm_lock *lock) lock->ast_pending, lock->ml.type); BUG(); } - BUG_ON(!list_empty(&lock->ast_list)); if (lock->ast_pending) mlog(0, "lock has an ast getting flushed right now\n"); -- GitLab From ed680c4ad478d0fee9740f7d029087f181346564 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Fri, 31 Jul 2009 17:40:45 -0700 Subject: [PATCH 0640/1342] Linux 2.6.31-rc5 --- Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Makefile b/Makefile index 063d738405e..0d46615bffe 100644 --- a/Makefile +++ b/Makefile @@ -1,7 +1,7 @@ VERSION = 2 PATCHLEVEL = 6 SUBLEVEL = 31 -EXTRAVERSION = -rc4 +EXTRAVERSION = -rc5 NAME = Man-Eating Seals of Antiquity # *DOCUMENTATION* -- GitLab From fef246672b009cf3f7a74e2fc9a76932ef2eeed2 Mon Sep 17 00:00:00 2001 From: "Martin K. Petersen" Date: Fri, 31 Jul 2009 11:49:10 -0400 Subject: [PATCH 0641/1342] block: Make blk_queue_stack_limits use the new stacking interface blk_queue_stack_limits() has been superceded by blk_stack_limits() and disk_stack_limits(). Wrap the function call for now, we'll deprecate it later. Signed-off-by: Martin K. Petersen Signed-off-by: Jens Axboe --- block/blk-settings.c | 22 +--------------------- 1 file changed, 1 insertion(+), 21 deletions(-) diff --git a/block/blk-settings.c b/block/blk-settings.c index 8a3ea3bba10..8e86e2d2b14 100644 --- a/block/blk-settings.c +++ b/block/blk-settings.c @@ -433,27 +433,7 @@ EXPORT_SYMBOL(blk_queue_io_opt); **/ void blk_queue_stack_limits(struct request_queue *t, struct request_queue *b) { - /* zero is "infinity" */ - t->limits.max_sectors = min_not_zero(queue_max_sectors(t), - queue_max_sectors(b)); - - t->limits.max_hw_sectors = min_not_zero(queue_max_hw_sectors(t), - queue_max_hw_sectors(b)); - - t->limits.seg_boundary_mask = min_not_zero(queue_segment_boundary(t), - queue_segment_boundary(b)); - - t->limits.max_phys_segments = min_not_zero(queue_max_phys_segments(t), - queue_max_phys_segments(b)); - - t->limits.max_hw_segments = min_not_zero(queue_max_hw_segments(t), - queue_max_hw_segments(b)); - - t->limits.max_segment_size = min_not_zero(queue_max_segment_size(t), - queue_max_segment_size(b)); - - t->limits.logical_block_size = max(queue_logical_block_size(t), - queue_logical_block_size(b)); + blk_stack_limits(&t->limits, &b->limits, 0); if (!t->queue_lock) WARN_ON_ONCE(1); -- GitLab From 7c958e32649e0c35801762878fb0b6da8c55a515 Mon Sep 17 00:00:00 2001 From: "Martin K. Petersen" Date: Fri, 31 Jul 2009 11:49:11 -0400 Subject: [PATCH 0642/1342] block: Add a wrapper for setting minimum request size without a queue Introduce blk_limits_io_min() and make blk_queue_io_min() call it. Signed-off-by: Mike Snitzer Signed-off-by: Martin K. Petersen Signed-off-by: Jens Axboe --- block/blk-settings.c | 31 ++++++++++++++++++++++++------- include/linux/blkdev.h | 1 + 2 files changed, 25 insertions(+), 7 deletions(-) diff --git a/block/blk-settings.c b/block/blk-settings.c index 8e86e2d2b14..1f719743416 100644 --- a/block/blk-settings.c +++ b/block/blk-settings.c @@ -383,6 +383,29 @@ void blk_queue_alignment_offset(struct request_queue *q, unsigned int offset) } EXPORT_SYMBOL(blk_queue_alignment_offset); +/** + * blk_limits_io_min - set minimum request size for a device + * @limits: the queue limits + * @min: smallest I/O size in bytes + * + * Description: + * Some devices have an internal block size bigger than the reported + * hardware sector size. This function can be used to signal the + * smallest I/O the device can perform without incurring a performance + * penalty. + */ +void blk_limits_io_min(struct queue_limits *limits, unsigned int min) +{ + limits->io_min = min; + + if (limits->io_min < limits->logical_block_size) + limits->io_min = limits->logical_block_size; + + if (limits->io_min < limits->physical_block_size) + limits->io_min = limits->physical_block_size; +} +EXPORT_SYMBOL(blk_limits_io_min); + /** * blk_queue_io_min - set minimum request size for the queue * @q: the request queue for the device @@ -396,13 +419,7 @@ EXPORT_SYMBOL(blk_queue_alignment_offset); */ void blk_queue_io_min(struct request_queue *q, unsigned int min) { - q->limits.io_min = min; - - if (q->limits.io_min < q->limits.logical_block_size) - q->limits.io_min = q->limits.logical_block_size; - - if (q->limits.io_min < q->limits.physical_block_size) - q->limits.io_min = q->limits.physical_block_size; + blk_limits_io_min(&q->limits, min); } EXPORT_SYMBOL(blk_queue_io_min); diff --git a/include/linux/blkdev.h b/include/linux/blkdev.h index e7cb5dbf6c2..69103e053c9 100644 --- a/include/linux/blkdev.h +++ b/include/linux/blkdev.h @@ -913,6 +913,7 @@ extern void blk_queue_logical_block_size(struct request_queue *, unsigned short) extern void blk_queue_physical_block_size(struct request_queue *, unsigned short); extern void blk_queue_alignment_offset(struct request_queue *q, unsigned int alignment); +extern void blk_limits_io_min(struct queue_limits *limits, unsigned int min); extern void blk_queue_io_min(struct request_queue *q, unsigned int min); extern void blk_queue_io_opt(struct request_queue *q, unsigned int opt); extern void blk_set_default_limits(struct queue_limits *lim); -- GitLab From 70dd5bf3b99964d52862ad2810c24cc32a553535 Mon Sep 17 00:00:00 2001 From: "Martin K. Petersen" Date: Fri, 31 Jul 2009 11:49:12 -0400 Subject: [PATCH 0643/1342] block: Stack optimal I/O size When stacking block devices ensure that optimal I/O size is scaled accordingly. Signed-off-by: Martin K. Petersen Reviewed-by: Mike Snitzer Signed-off-by: Jens Axboe --- block/blk-settings.c | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/block/blk-settings.c b/block/blk-settings.c index 1f719743416..e1327ddfc13 100644 --- a/block/blk-settings.c +++ b/block/blk-settings.c @@ -7,6 +7,7 @@ #include #include #include /* for max_pfn/max_low_pfn */ +#include #include "blk.h" @@ -520,6 +521,16 @@ int blk_stack_limits(struct queue_limits *t, struct queue_limits *b, return -1; } + /* Find lcm() of optimal I/O size */ + if (t->io_opt && b->io_opt) + t->io_opt = (t->io_opt * b->io_opt) / gcd(t->io_opt, b->io_opt); + else if (b->io_opt) + t->io_opt = b->io_opt; + + /* Verify that optimal I/O size is a multiple of io_min */ + if (t->io_min && t->io_opt % t->io_min) + return -1; + return 0; } EXPORT_SYMBOL(blk_stack_limits); -- GitLab From 7e5f5fb09e6fc657f21816b5a18ba645a913368e Mon Sep 17 00:00:00 2001 From: "Martin K. Petersen" Date: Fri, 31 Jul 2009 11:49:13 -0400 Subject: [PATCH 0644/1342] block: Update topology documentation Update topology comments and sysfs documentation based upon discussions with Neil Brown. Signed-off-by: Martin K. Petersen Signed-off-by: Jens Axboe --- Documentation/ABI/testing/sysfs-block | 37 +++++++++++++++++---------- block/blk-settings.c | 19 +++++++++----- 2 files changed, 36 insertions(+), 20 deletions(-) diff --git a/Documentation/ABI/testing/sysfs-block b/Documentation/ABI/testing/sysfs-block index cbbd3e06994..5f3bedaf8e3 100644 --- a/Documentation/ABI/testing/sysfs-block +++ b/Documentation/ABI/testing/sysfs-block @@ -94,28 +94,37 @@ What: /sys/block//queue/physical_block_size Date: May 2009 Contact: Martin K. Petersen Description: - This is the smallest unit the storage device can write - without resorting to read-modify-write operation. It is - usually the same as the logical block size but may be - bigger. One example is SATA drives with 4KB sectors - that expose a 512-byte logical block size to the - operating system. + This is the smallest unit a physical storage device can + write atomically. It is usually the same as the logical + block size but may be bigger. One example is SATA + drives with 4KB sectors that expose a 512-byte logical + block size to the operating system. For stacked block + devices the physical_block_size variable contains the + maximum physical_block_size of the component devices. What: /sys/block//queue/minimum_io_size Date: April 2009 Contact: Martin K. Petersen Description: - Storage devices may report a preferred minimum I/O size, - which is the smallest request the device can perform - without incurring a read-modify-write penalty. For disk - drives this is often the physical block size. For RAID - arrays it is often the stripe chunk size. + Storage devices may report a granularity or preferred + minimum I/O size which is the smallest request the + device can perform without incurring a performance + penalty. For disk drives this is often the physical + block size. For RAID arrays it is often the stripe + chunk size. A properly aligned multiple of + minimum_io_size is the preferred request size for + workloads where a high number of I/O operations is + desired. What: /sys/block//queue/optimal_io_size Date: April 2009 Contact: Martin K. Petersen Description: Storage devices may report an optimal I/O size, which is - the device's preferred unit of receiving I/O. This is - rarely reported for disk drives. For RAID devices it is - usually the stripe width or the internal block size. + the device's preferred unit for sustained I/O. This is + rarely reported for disk drives. For RAID arrays it is + usually the stripe width or the internal track size. A + properly aligned multiple of optimal_io_size is the + preferred request size for workloads where sustained + throughput is desired. If no optimal I/O size is + reported this file contains 0. diff --git a/block/blk-settings.c b/block/blk-settings.c index e1327ddfc13..476d8706507 100644 --- a/block/blk-settings.c +++ b/block/blk-settings.c @@ -413,10 +413,13 @@ EXPORT_SYMBOL(blk_limits_io_min); * @min: smallest I/O size in bytes * * Description: - * Some devices have an internal block size bigger than the reported - * hardware sector size. This function can be used to signal the - * smallest I/O the device can perform without incurring a performance - * penalty. + * Storage devices may report a granularity or preferred minimum I/O + * size which is the smallest request the device can perform without + * incurring a performance penalty. For disk drives this is often the + * physical block size. For RAID arrays it is often the stripe chunk + * size. A properly aligned multiple of minimum_io_size is the + * preferred request size for workloads where a high number of I/O + * operations is desired. */ void blk_queue_io_min(struct request_queue *q, unsigned int min) { @@ -430,8 +433,12 @@ EXPORT_SYMBOL(blk_queue_io_min); * @opt: optimal request size in bytes * * Description: - * Drivers can call this function to set the preferred I/O request - * size for devices that report such a value. + * Storage devices may report an optimal I/O size, which is the + * device's preferred unit for sustained I/O. This is rarely reported + * for disk drives. For RAID arrays it is usually the stripe width or + * the internal track size. A properly aligned multiple of + * optimal_io_size is the preferred request size for workloads where + * sustained throughput is desired. */ void blk_queue_io_opt(struct request_queue *q, unsigned int opt) { -- GitLab From 2d1b6949d2c855f195de0f5146625015ecca3944 Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Sat, 1 Aug 2009 13:15:36 +0200 Subject: [PATCH 0645/1342] perf_counter tools: Fix link errors with older toolchains On older distros (F8 for example) the perf build could fail with such missing symbols: LINK perf /usr/lib/gcc/x86_64-redhat-linux/4.3.2/../../../../lib64/libbfd.a(bfd.o): In function `bfd_demangle': (.text+0x2b3): undefined reference to `cplus_demangle' /usr/lib/gcc/x86_64-redhat-linux/4.3.2/../../../../lib64/libbfd.a(bfd.o): In function `bfd_demangle': Link in -liberty too. Cc: Peter Zijlstra Cc: Mike Galbraith Cc: Paul Mackerras Cc: Arnaldo Carvalho de Melo Cc: Frederic Weisbecker LKML-Reference: Signed-off-by: Ingo Molnar --- tools/perf/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/tools/perf/Makefile b/tools/perf/Makefile index a5e9b876ca0..4b20fa47c3a 100644 --- a/tools/perf/Makefile +++ b/tools/perf/Makefile @@ -345,7 +345,7 @@ BUILTIN_OBJS += builtin-stat.o BUILTIN_OBJS += builtin-top.o PERFLIBS = $(LIB_FILE) -EXTLIBS = -lbfd +EXTLIBS = -lbfd -liberty # # Platform specific tweaks -- GitLab From a97778457f22181e8c38c4cd7d7e528378738a98 Mon Sep 17 00:00:00 2001 From: Ryusuke Konishi Date: Tue, 28 Jul 2009 17:55:29 +0900 Subject: [PATCH 0646/1342] nilfs2: fix oops due to inconsistent state in page with discrete b-tree nodes Andrea Gelmini gave me a report that a kernel oops hit on a nilfs filesystem with a 1KB block size when doing rsync. This turned out to be caused by an inconsistency of dirty state between a page and its buffers storing b-tree node blocks. If the page had multiple buffers split over multiple logs, and if the logs were written at a time, a dirty flag remained in the page even every dirty flag in the buffers was cleared. This will fix the failure by dropping the dirty flag properly for pages with the discrete multiple b-tree nodes. Reported-by: Andrea Gelmini Signed-off-by: Ryusuke Konishi Tested-by: Andrea Gelmini Cc: stable@kernel.org --- fs/nilfs2/segment.c | 16 +++++++++++++++- 1 file changed, 15 insertions(+), 1 deletion(-) diff --git a/fs/nilfs2/segment.c b/fs/nilfs2/segment.c index 8b5e4778cf2..51ff3d0a4ee 100644 --- a/fs/nilfs2/segment.c +++ b/fs/nilfs2/segment.c @@ -1859,12 +1859,26 @@ static void nilfs_end_page_io(struct page *page, int err) if (!page) return; - if (buffer_nilfs_node(page_buffers(page)) && !PageWriteback(page)) + if (buffer_nilfs_node(page_buffers(page)) && !PageWriteback(page)) { /* * For b-tree node pages, this function may be called twice * or more because they might be split in a segment. */ + if (PageDirty(page)) { + /* + * For pages holding split b-tree node buffers, dirty + * flag on the buffers may be cleared discretely. + * In that case, the page is once redirtied for + * remaining buffers, and it must be cancelled if + * all the buffers get cleaned later. + */ + lock_page(page); + if (nilfs_page_buffers_clean(page)) + __nilfs_clear_page_dirty(page); + unlock_page(page); + } return; + } __nilfs_end_page_io(page, err); } -- GitLab From 0083fc2c50e6c5127c2802ad323adf8143ab7856 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sat, 1 Aug 2009 10:34:56 -0700 Subject: [PATCH 0647/1342] do_sigaltstack: avoid copying 'stack_t' as a structure to user space Ulrich Drepper correctly points out that there is generally padding in the structure on 64-bit hosts, and that copying the structure from kernel to user space can leak information from the kernel stack in those padding bytes. Avoid the whole issue by just copying the three members one by one instead, which also means that the function also can avoid the need for a stack frame. This also happens to match how we copy the new structure from user space, so it all even makes sense. [ The obvious solution of adding a memset() generates horrid code, gcc does really stupid things. ] Reported-by: Ulrich Drepper Signed-off-by: Linus Torvalds --- kernel/signal.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-) diff --git a/kernel/signal.c b/kernel/signal.c index ccf1ceedaeb..f268372c0cc 100644 --- a/kernel/signal.c +++ b/kernel/signal.c @@ -2454,11 +2454,9 @@ do_sigaltstack (const stack_t __user *uss, stack_t __user *uoss, unsigned long s stack_t oss; int error; - if (uoss) { - oss.ss_sp = (void __user *) current->sas_ss_sp; - oss.ss_size = current->sas_ss_size; - oss.ss_flags = sas_ss_flags(sp); - } + oss.ss_sp = (void __user *) current->sas_ss_sp; + oss.ss_size = current->sas_ss_size; + oss.ss_flags = sas_ss_flags(sp); if (uss) { void __user *ss_sp; @@ -2501,13 +2499,16 @@ do_sigaltstack (const stack_t __user *uss, stack_t __user *uoss, unsigned long s current->sas_ss_size = ss_size; } + error = 0; if (uoss) { error = -EFAULT; - if (copy_to_user(uoss, &oss, sizeof(oss))) + if (!access_ok(VERIFY_WRITE, uoss, sizeof(*uoss))) goto out; + error = __put_user(oss.ss_sp, &uoss->ss_sp) | + __put_user(oss.ss_size, &uoss->ss_size) | + __put_user(oss.ss_flags, &uoss->ss_flags); } - error = 0; out: return error; } -- GitLab From 0dd8486b5cfe8048e0613334659d9252ecd1b08a Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sat, 1 Aug 2009 11:18:56 -0700 Subject: [PATCH 0648/1342] do_sigaltstack: small cleanups The previous commit ("do_sigaltstack: avoid copying 'stack_t' as a structure to user space") fixed a real bug. This one just cleans up the copy from user space to that gcc can generate better code for it (and so that it looks the same as the later copy back to user space). Signed-off-by: Linus Torvalds --- kernel/signal.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-) diff --git a/kernel/signal.c b/kernel/signal.c index f268372c0cc..64c5deeaca5 100644 --- a/kernel/signal.c +++ b/kernel/signal.c @@ -2464,10 +2464,12 @@ do_sigaltstack (const stack_t __user *uss, stack_t __user *uoss, unsigned long s int ss_flags; error = -EFAULT; - if (!access_ok(VERIFY_READ, uss, sizeof(*uss)) - || __get_user(ss_sp, &uss->ss_sp) - || __get_user(ss_flags, &uss->ss_flags) - || __get_user(ss_size, &uss->ss_size)) + if (!access_ok(VERIFY_READ, uss, sizeof(*uss))) + goto out; + error = __get_user(ss_sp, &uss->ss_sp) | + __get_user(ss_flags, &uss->ss_flags) | + __get_user(ss_size, &uss->ss_size); + if (error) goto out; error = -EPERM; -- GitLab From 550e7fd8afb7664ae7cedb398c407694e2bf7d3c Mon Sep 17 00:00:00 2001 From: Henrique de Moraes Holschuh Date: Sat, 1 Aug 2009 12:04:17 -0300 Subject: [PATCH 0649/1342] thinkpad-acpi: disable broken bay and dock subdrivers Currently, the ThinkPad-ACPI bay and dock drivers are completely broken, and cause a NULL pointer derreference in kernel mode (and, therefore, an OOPS) when they try to issue events (i.e. on dock, undock, bay ejection, etc). OTOH, the standard ACPI dock driver can handle the hotplug bays and docks of the ThinkPads just fine (including batteries) as of 2.6.27. In fact, it does a much better job of it than thinkpad-acpi ever did. It is just not worth the hassle to find a way to fix this crap without breaking the (deprecated) thinkpad-acpi dock/bay ABI. This is old, deprecated code that sees little testing or use. As a quick fix suitable for -stable backports, mark the thinkpad-acpi bay and dock subdrivers as BROKEN in Kconfig. The dead code will be removed by a later patch. This fixes bugzilla #13669, and should be applied to 2.6.27 and later. Signed-off-by: Henrique de Moraes Holschuh Reported-by: Joerg Platte Cc: stable@kernel.org Signed-off-by: Len Brown --- drivers/platform/x86/Kconfig | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/platform/x86/Kconfig b/drivers/platform/x86/Kconfig index 46dad12f952..6335f63892d 100644 --- a/drivers/platform/x86/Kconfig +++ b/drivers/platform/x86/Kconfig @@ -281,6 +281,7 @@ config THINKPAD_ACPI_DOCK bool "Legacy Docking Station Support" depends on THINKPAD_ACPI depends on ACPI_DOCK=n + depends on BROKEN default n ---help--- Allows the thinkpad_acpi driver to handle docking station events. @@ -294,7 +295,8 @@ config THINKPAD_ACPI_DOCK config THINKPAD_ACPI_BAY bool "Legacy Removable Bay Support" depends on THINKPAD_ACPI - default y + depends on BROKEN + default n ---help--- Allows the thinkpad_acpi driver to handle removable bays. It will electrically disable the device in the bay, and also generate -- GitLab From 1f6fc2de9525e34ee93bd392fa046369a8cfbf1e Mon Sep 17 00:00:00 2001 From: Henrique de Moraes Holschuh Date: Sat, 1 Aug 2009 12:04:18 -0300 Subject: [PATCH 0650/1342] thinkpad-acpi: remove dock and bay subdrivers The standard ACPI dock driver can handle the hotplug bays and docks of the ThinkPads just fine (including batteries) as of 2.6.27, and the code in thinkpad-acpi for the dock and bay subdrivers is currently broken anyway... Userspace needs some love to support the two-stage ejection nicely, but it is simple enough to do through udev rules (you don't even need HAL) so this wouldn't justify fixing the dock and bay subdrivers, either. That leaves warm-swap bays (_EJ3) support for thinkpad-acpi, as well as support for the weird dock of the model 570, but since such support has never left the "experimental" stage, it is also not a strong enough reason to find a way to fix this code. Users of ThinkPads with warm-swap bays are urged to request that _EJ3 support be added to the regular ACPI dock driver, if such feature is indeed useful for them. Signed-off-by: Henrique de Moraes Holschuh Signed-off-by: Len Brown --- Documentation/laptops/thinkpad-acpi.txt | 127 --------- drivers/platform/x86/Kconfig | 27 -- drivers/platform/x86/thinkpad_acpi.c | 327 ------------------------ 3 files changed, 481 deletions(-) diff --git a/Documentation/laptops/thinkpad-acpi.txt b/Documentation/laptops/thinkpad-acpi.txt index f2296ecedb8..e2ddcdeb61b 100644 --- a/Documentation/laptops/thinkpad-acpi.txt +++ b/Documentation/laptops/thinkpad-acpi.txt @@ -36,8 +36,6 @@ detailed description): - Bluetooth enable and disable - video output switching, expansion control - ThinkLight on and off - - limited docking and undocking - - UltraBay eject - CMOS/UCMS control - LED control - ACPI sounds @@ -729,131 +727,6 @@ cannot be read or if it is unknown, thinkpad-acpi will report it as "off". It is impossible to know if the status returned through sysfs is valid. -Docking / undocking -- /proc/acpi/ibm/dock ------------------------------------------- - -Docking and undocking (e.g. with the X4 UltraBase) requires some -actions to be taken by the operating system to safely make or break -the electrical connections with the dock. - -The docking feature of this driver generates the following ACPI events: - - ibm/dock GDCK 00000003 00000001 -- eject request - ibm/dock GDCK 00000003 00000002 -- undocked - ibm/dock GDCK 00000000 00000003 -- docked - -NOTE: These events will only be generated if the laptop was docked -when originally booted. This is due to the current lack of support for -hot plugging of devices in the Linux ACPI framework. If the laptop was -booted while not in the dock, the following message is shown in the -logs: - - Mar 17 01:42:34 aero kernel: thinkpad_acpi: dock device not present - -In this case, no dock-related events are generated but the dock and -undock commands described below still work. They can be executed -manually or triggered by Fn key combinations (see the example acpid -configuration files included in the driver tarball package available -on the web site). - -When the eject request button on the dock is pressed, the first event -above is generated. The handler for this event should issue the -following command: - - echo undock > /proc/acpi/ibm/dock - -After the LED on the dock goes off, it is safe to eject the laptop. -Note: if you pressed this key by mistake, go ahead and eject the -laptop, then dock it back in. Otherwise, the dock may not function as -expected. - -When the laptop is docked, the third event above is generated. The -handler for this event should issue the following command to fully -enable the dock: - - echo dock > /proc/acpi/ibm/dock - -The contents of the /proc/acpi/ibm/dock file shows the current status -of the dock, as provided by the ACPI framework. - -The docking support in this driver does not take care of enabling or -disabling any other devices you may have attached to the dock. For -example, a CD drive plugged into the UltraBase needs to be disabled or -enabled separately. See the provided example acpid configuration files -for how this can be accomplished. - -There is no support yet for PCI devices that may be attached to a -docking station, e.g. in the ThinkPad Dock II. The driver currently -does not recognize, enable or disable such devices. This means that -the only docking stations currently supported are the X-series -UltraBase docks and "dumb" port replicators like the Mini Dock (the -latter don't need any ACPI support, actually). - - -UltraBay eject -- /proc/acpi/ibm/bay ------------------------------------- - -Inserting or ejecting an UltraBay device requires some actions to be -taken by the operating system to safely make or break the electrical -connections with the device. - -This feature generates the following ACPI events: - - ibm/bay MSTR 00000003 00000000 -- eject request - ibm/bay MSTR 00000001 00000000 -- eject lever inserted - -NOTE: These events will only be generated if the UltraBay was present -when the laptop was originally booted (on the X series, the UltraBay -is in the dock, so it may not be present if the laptop was undocked). -This is due to the current lack of support for hot plugging of devices -in the Linux ACPI framework. If the laptop was booted without the -UltraBay, the following message is shown in the logs: - - Mar 17 01:42:34 aero kernel: thinkpad_acpi: bay device not present - -In this case, no bay-related events are generated but the eject -command described below still works. It can be executed manually or -triggered by a hot key combination. - -Sliding the eject lever generates the first event shown above. The -handler for this event should take whatever actions are necessary to -shut down the device in the UltraBay (e.g. call idectl), then issue -the following command: - - echo eject > /proc/acpi/ibm/bay - -After the LED on the UltraBay goes off, it is safe to pull out the -device. - -When the eject lever is inserted, the second event above is -generated. The handler for this event should take whatever actions are -necessary to enable the UltraBay device (e.g. call idectl). - -The contents of the /proc/acpi/ibm/bay file shows the current status -of the UltraBay, as provided by the ACPI framework. - -EXPERIMENTAL warm eject support on the 600e/x, A22p and A3x (To use -this feature, you need to supply the experimental=1 parameter when -loading the module): - -These models do not have a button near the UltraBay device to request -a hot eject but rather require the laptop to be put to sleep -(suspend-to-ram) before the bay device is ejected or inserted). -The sequence of steps to eject the device is as follows: - - echo eject > /proc/acpi/ibm/bay - put the ThinkPad to sleep - remove the drive - resume from sleep - cat /proc/acpi/ibm/bay should show that the drive was removed - -On the A3x, both the UltraBay 2000 and UltraBay Plus devices are -supported. Use "eject2" instead of "eject" for the second bay. - -Note: the UltraBay eject support on the 600e/x, A22p and A3x is -EXPERIMENTAL and may not work as expected. USE WITH CAUTION! - - CMOS/UCMS control ----------------- diff --git a/drivers/platform/x86/Kconfig b/drivers/platform/x86/Kconfig index 6335f63892d..77c6097ced8 100644 --- a/drivers/platform/x86/Kconfig +++ b/drivers/platform/x86/Kconfig @@ -277,33 +277,6 @@ config THINKPAD_ACPI_UNSAFE_LEDS Say N here, unless you are building a kernel for your own use, and need to control the important firmware LEDs. -config THINKPAD_ACPI_DOCK - bool "Legacy Docking Station Support" - depends on THINKPAD_ACPI - depends on ACPI_DOCK=n - depends on BROKEN - default n - ---help--- - Allows the thinkpad_acpi driver to handle docking station events. - This support was made obsolete by the generic ACPI docking station - support (CONFIG_ACPI_DOCK). It will allow locking and removing the - laptop from the docking station, but will not properly connect PCI - devices. - - If you are not sure, say N here. - -config THINKPAD_ACPI_BAY - bool "Legacy Removable Bay Support" - depends on THINKPAD_ACPI - depends on BROKEN - default n - ---help--- - Allows the thinkpad_acpi driver to handle removable bays. It will - electrically disable the device in the bay, and also generate - notifications when the bay lever is ejected or inserted. - - If you are not sure, say Y here. - config THINKPAD_ACPI_VIDEO bool "Video output control support" depends on THINKPAD_ACPI diff --git a/drivers/platform/x86/thinkpad_acpi.c b/drivers/platform/x86/thinkpad_acpi.c index a463fd72c49..27d68e719e9 100644 --- a/drivers/platform/x86/thinkpad_acpi.c +++ b/drivers/platform/x86/thinkpad_acpi.c @@ -239,12 +239,6 @@ struct ibm_init_struct { }; static struct { -#ifdef CONFIG_THINKPAD_ACPI_BAY - u32 bay_status:1; - u32 bay_eject:1; - u32 bay_status2:1; - u32 bay_eject2:1; -#endif u32 bluetooth:1; u32 hotkey:1; u32 hotkey_mask:1; @@ -589,18 +583,6 @@ static int acpi_ec_write(int i, u8 v) return 1; } -#if defined(CONFIG_THINKPAD_ACPI_DOCK) || defined(CONFIG_THINKPAD_ACPI_BAY) -static int _sta(acpi_handle handle) -{ - int status; - - if (!handle || !acpi_evalf(handle, &status, "_STA", "d")) - status = 0; - - return status; -} -#endif - static int issue_thinkpad_cmos_command(int cmos_cmd) { if (!cmos_handle) @@ -4441,293 +4423,6 @@ static struct ibm_struct light_driver_data = { .exit = light_exit, }; -/************************************************************************* - * Dock subdriver - */ - -#ifdef CONFIG_THINKPAD_ACPI_DOCK - -static void dock_notify(struct ibm_struct *ibm, u32 event); -static int dock_read(char *p); -static int dock_write(char *buf); - -TPACPI_HANDLE(dock, root, "\\_SB.GDCK", /* X30, X31, X40 */ - "\\_SB.PCI0.DOCK", /* 600e/x,770e,770x,A2xm/p,T20-22,X20-21 */ - "\\_SB.PCI0.PCI1.DOCK", /* all others */ - "\\_SB.PCI.ISA.SLCE", /* 570 */ - ); /* A21e,G4x,R30,R31,R32,R40,R40e,R50e */ - -/* don't list other alternatives as we install a notify handler on the 570 */ -TPACPI_HANDLE(pci, root, "\\_SB.PCI"); /* 570 */ - -static const struct acpi_device_id ibm_pci_device_ids[] = { - {PCI_ROOT_HID_STRING, 0}, - {"", 0}, -}; - -static struct tp_acpi_drv_struct ibm_dock_acpidriver[2] = { - { - .notify = dock_notify, - .handle = &dock_handle, - .type = ACPI_SYSTEM_NOTIFY, - }, - { - /* THIS ONE MUST NEVER BE USED FOR DRIVER AUTOLOADING. - * We just use it to get notifications of dock hotplug - * in very old thinkpads */ - .hid = ibm_pci_device_ids, - .notify = dock_notify, - .handle = &pci_handle, - .type = ACPI_SYSTEM_NOTIFY, - }, -}; - -static struct ibm_struct dock_driver_data[2] = { - { - .name = "dock", - .read = dock_read, - .write = dock_write, - .acpi = &ibm_dock_acpidriver[0], - }, - { - .name = "dock", - .acpi = &ibm_dock_acpidriver[1], - }, -}; - -#define dock_docked() (_sta(dock_handle) & 1) - -static int __init dock_init(struct ibm_init_struct *iibm) -{ - vdbg_printk(TPACPI_DBG_INIT, "initializing dock subdriver\n"); - - TPACPI_ACPIHANDLE_INIT(dock); - - vdbg_printk(TPACPI_DBG_INIT, "dock is %s\n", - str_supported(dock_handle != NULL)); - - return (dock_handle)? 0 : 1; -} - -static int __init dock_init2(struct ibm_init_struct *iibm) -{ - int dock2_needed; - - vdbg_printk(TPACPI_DBG_INIT, "initializing dock subdriver part 2\n"); - - if (dock_driver_data[0].flags.acpi_driver_registered && - dock_driver_data[0].flags.acpi_notify_installed) { - TPACPI_ACPIHANDLE_INIT(pci); - dock2_needed = (pci_handle != NULL); - vdbg_printk(TPACPI_DBG_INIT, - "dock PCI handler for the TP 570 is %s\n", - str_supported(dock2_needed)); - } else { - vdbg_printk(TPACPI_DBG_INIT, - "dock subdriver part 2 not required\n"); - dock2_needed = 0; - } - - return (dock2_needed)? 0 : 1; -} - -static void dock_notify(struct ibm_struct *ibm, u32 event) -{ - int docked = dock_docked(); - int pci = ibm->acpi->hid && ibm->acpi->device && - acpi_match_device_ids(ibm->acpi->device, ibm_pci_device_ids); - int data; - - if (event == 1 && !pci) /* 570 */ - data = 1; /* button */ - else if (event == 1 && pci) /* 570 */ - data = 3; /* dock */ - else if (event == 3 && docked) - data = 1; /* button */ - else if (event == 3 && !docked) - data = 2; /* undock */ - else if (event == 0 && docked) - data = 3; /* dock */ - else { - printk(TPACPI_ERR "unknown dock event %d, status %d\n", - event, _sta(dock_handle)); - data = 0; /* unknown */ - } - acpi_bus_generate_proc_event(ibm->acpi->device, event, data); - acpi_bus_generate_netlink_event(ibm->acpi->device->pnp.device_class, - dev_name(&ibm->acpi->device->dev), - event, data); -} - -static int dock_read(char *p) -{ - int len = 0; - int docked = dock_docked(); - - if (!dock_handle) - len += sprintf(p + len, "status:\t\tnot supported\n"); - else if (!docked) - len += sprintf(p + len, "status:\t\tundocked\n"); - else { - len += sprintf(p + len, "status:\t\tdocked\n"); - len += sprintf(p + len, "commands:\tdock, undock\n"); - } - - return len; -} - -static int dock_write(char *buf) -{ - char *cmd; - - if (!dock_docked()) - return -ENODEV; - - while ((cmd = next_cmd(&buf))) { - if (strlencmp(cmd, "undock") == 0) { - if (!acpi_evalf(dock_handle, NULL, "_DCK", "vd", 0) || - !acpi_evalf(dock_handle, NULL, "_EJ0", "vd", 1)) - return -EIO; - } else if (strlencmp(cmd, "dock") == 0) { - if (!acpi_evalf(dock_handle, NULL, "_DCK", "vd", 1)) - return -EIO; - } else - return -EINVAL; - } - - return 0; -} - -#endif /* CONFIG_THINKPAD_ACPI_DOCK */ - -/************************************************************************* - * Bay subdriver - */ - -#ifdef CONFIG_THINKPAD_ACPI_BAY - -TPACPI_HANDLE(bay, root, "\\_SB.PCI.IDE.SECN.MAST", /* 570 */ - "\\_SB.PCI0.IDE0.IDES.IDSM", /* 600e/x, 770e, 770x */ - "\\_SB.PCI0.SATA.SCND.MSTR", /* T60, X60, Z60 */ - "\\_SB.PCI0.IDE0.SCND.MSTR", /* all others */ - ); /* A21e, R30, R31 */ -TPACPI_HANDLE(bay_ej, bay, "_EJ3", /* 600e/x, A2xm/p, A3x */ - "_EJ0", /* all others */ - ); /* 570,A21e,G4x,R30,R31,R32,R40e,R50e */ -TPACPI_HANDLE(bay2, root, "\\_SB.PCI0.IDE0.PRIM.SLAV", /* A3x, R32 */ - "\\_SB.PCI0.IDE0.IDEP.IDPS", /* 600e/x, 770e, 770x */ - ); /* all others */ -TPACPI_HANDLE(bay2_ej, bay2, "_EJ3", /* 600e/x, 770e, A3x */ - "_EJ0", /* 770x */ - ); /* all others */ - -static int __init bay_init(struct ibm_init_struct *iibm) -{ - vdbg_printk(TPACPI_DBG_INIT, "initializing bay subdriver\n"); - - TPACPI_ACPIHANDLE_INIT(bay); - if (bay_handle) - TPACPI_ACPIHANDLE_INIT(bay_ej); - TPACPI_ACPIHANDLE_INIT(bay2); - if (bay2_handle) - TPACPI_ACPIHANDLE_INIT(bay2_ej); - - tp_features.bay_status = bay_handle && - acpi_evalf(bay_handle, NULL, "_STA", "qv"); - tp_features.bay_status2 = bay2_handle && - acpi_evalf(bay2_handle, NULL, "_STA", "qv"); - - tp_features.bay_eject = bay_handle && bay_ej_handle && - (strlencmp(bay_ej_path, "_EJ0") == 0 || experimental); - tp_features.bay_eject2 = bay2_handle && bay2_ej_handle && - (strlencmp(bay2_ej_path, "_EJ0") == 0 || experimental); - - vdbg_printk(TPACPI_DBG_INIT, - "bay 1: status %s, eject %s; bay 2: status %s, eject %s\n", - str_supported(tp_features.bay_status), - str_supported(tp_features.bay_eject), - str_supported(tp_features.bay_status2), - str_supported(tp_features.bay_eject2)); - - return (tp_features.bay_status || tp_features.bay_eject || - tp_features.bay_status2 || tp_features.bay_eject2)? 0 : 1; -} - -static void bay_notify(struct ibm_struct *ibm, u32 event) -{ - acpi_bus_generate_proc_event(ibm->acpi->device, event, 0); - acpi_bus_generate_netlink_event(ibm->acpi->device->pnp.device_class, - dev_name(&ibm->acpi->device->dev), - event, 0); -} - -#define bay_occupied(b) (_sta(b##_handle) & 1) - -static int bay_read(char *p) -{ - int len = 0; - int occupied = bay_occupied(bay); - int occupied2 = bay_occupied(bay2); - int eject, eject2; - - len += sprintf(p + len, "status:\t\t%s\n", - tp_features.bay_status ? - (occupied ? "occupied" : "unoccupied") : - "not supported"); - if (tp_features.bay_status2) - len += sprintf(p + len, "status2:\t%s\n", occupied2 ? - "occupied" : "unoccupied"); - - eject = tp_features.bay_eject && occupied; - eject2 = tp_features.bay_eject2 && occupied2; - - if (eject && eject2) - len += sprintf(p + len, "commands:\teject, eject2\n"); - else if (eject) - len += sprintf(p + len, "commands:\teject\n"); - else if (eject2) - len += sprintf(p + len, "commands:\teject2\n"); - - return len; -} - -static int bay_write(char *buf) -{ - char *cmd; - - if (!tp_features.bay_eject && !tp_features.bay_eject2) - return -ENODEV; - - while ((cmd = next_cmd(&buf))) { - if (tp_features.bay_eject && strlencmp(cmd, "eject") == 0) { - if (!acpi_evalf(bay_ej_handle, NULL, NULL, "vd", 1)) - return -EIO; - } else if (tp_features.bay_eject2 && - strlencmp(cmd, "eject2") == 0) { - if (!acpi_evalf(bay2_ej_handle, NULL, NULL, "vd", 1)) - return -EIO; - } else - return -EINVAL; - } - - return 0; -} - -static struct tp_acpi_drv_struct ibm_bay_acpidriver = { - .notify = bay_notify, - .handle = &bay_handle, - .type = ACPI_SYSTEM_NOTIFY, -}; - -static struct ibm_struct bay_driver_data = { - .name = "bay", - .read = bay_read, - .write = bay_write, - .acpi = &ibm_bay_acpidriver, -}; - -#endif /* CONFIG_THINKPAD_ACPI_BAY */ - /************************************************************************* * CMOS subdriver */ @@ -7854,22 +7549,6 @@ static struct ibm_init_struct ibms_init[] __initdata = { .init = light_init, .data = &light_driver_data, }, -#ifdef CONFIG_THINKPAD_ACPI_DOCK - { - .init = dock_init, - .data = &dock_driver_data[0], - }, - { - .init = dock_init2, - .data = &dock_driver_data[1], - }, -#endif -#ifdef CONFIG_THINKPAD_ACPI_BAY - { - .init = bay_init, - .data = &bay_driver_data, - }, -#endif { .init = cmos_init, .data = &cmos_driver_data, @@ -7968,12 +7647,6 @@ TPACPI_PARAM(hotkey); TPACPI_PARAM(bluetooth); TPACPI_PARAM(video); TPACPI_PARAM(light); -#ifdef CONFIG_THINKPAD_ACPI_DOCK -TPACPI_PARAM(dock); -#endif -#ifdef CONFIG_THINKPAD_ACPI_BAY -TPACPI_PARAM(bay); -#endif /* CONFIG_THINKPAD_ACPI_BAY */ TPACPI_PARAM(cmos); TPACPI_PARAM(led); TPACPI_PARAM(beep); -- GitLab From 9b9d6b2434fe942895c341b9a982f158529788ec Mon Sep 17 00:00:00 2001 From: Jeff Layton Date: Fri, 31 Jul 2009 06:56:09 -0400 Subject: [PATCH 0651/1342] cifs: reinstate original behavior when uid=/gid= options are specified This patch fixes the regression reported here: http://bugzilla.kernel.org/show_bug.cgi?id=13861 commit 4ae1507f6d266d0cc3dd36e474d83aad70fec9e4 changed the default behavior when the uid= or gid= option was specified for a mount. The existing behavior was to always clobber the ownership information provided by the server when these options were specified. The above commit changed this behavior so that these options simply provided defaults when the server did not provide this information (unless "forceuid" or "forcegid" were specified) This patch reverts this change so that the default behavior is restored. It also adds "noforceuid" and "noforcegid" options to make it so that ownership information from the server is preserved, even when the mount has uid= or gid= options specified. It also adds a couple of printk notices that pop up when forceuid or forcegid options are specified without a uid= or gid= option. Reported-by: Tom Chiverton Reviewed-by: Shirish Pargaonkar Signed-off-by: Jeff Layton Signed-off-by: Steve French --- fs/cifs/connect.c | 42 ++++++++++++++++++++++++++++++------------ 1 file changed, 30 insertions(+), 12 deletions(-) diff --git a/fs/cifs/connect.c b/fs/cifs/connect.c index f2486889b7b..1f3345d7fa7 100644 --- a/fs/cifs/connect.c +++ b/fs/cifs/connect.c @@ -803,6 +803,10 @@ cifs_parse_mount_options(char *options, const char *devname, char *data; unsigned int temp_len, i, j; char separator[2]; + short int override_uid = -1; + short int override_gid = -1; + bool uid_specified = false; + bool gid_specified = false; separator[0] = ','; separator[1] = 0; @@ -1093,18 +1097,20 @@ cifs_parse_mount_options(char *options, const char *devname, "too long.\n"); return 1; } - } else if (strnicmp(data, "uid", 3) == 0) { - if (value && *value) - vol->linux_uid = - simple_strtoul(value, &value, 0); - } else if (strnicmp(data, "forceuid", 8) == 0) { - vol->override_uid = 1; - } else if (strnicmp(data, "gid", 3) == 0) { - if (value && *value) - vol->linux_gid = - simple_strtoul(value, &value, 0); - } else if (strnicmp(data, "forcegid", 8) == 0) { - vol->override_gid = 1; + } else if (!strnicmp(data, "uid", 3) && value && *value) { + vol->linux_uid = simple_strtoul(value, &value, 0); + uid_specified = true; + } else if (!strnicmp(data, "forceuid", 8)) { + override_uid = 1; + } else if (!strnicmp(data, "noforceuid", 10)) { + override_uid = 0; + } else if (!strnicmp(data, "gid", 3) && value && *value) { + vol->linux_gid = simple_strtoul(value, &value, 0); + gid_specified = true; + } else if (!strnicmp(data, "forcegid", 8)) { + override_gid = 1; + } else if (!strnicmp(data, "noforcegid", 10)) { + override_gid = 0; } else if (strnicmp(data, "file_mode", 4) == 0) { if (value && *value) { vol->file_mode = @@ -1355,6 +1361,18 @@ cifs_parse_mount_options(char *options, const char *devname, if (vol->UNCip == NULL) vol->UNCip = &vol->UNC[2]; + if (uid_specified) + vol->override_uid = override_uid; + else if (override_uid == 1) + printk(KERN_NOTICE "CIFS: ignoring forceuid mount option " + "specified with no uid= option.\n"); + + if (gid_specified) + vol->override_gid = override_gid; + else if (override_gid == 1) + printk(KERN_NOTICE "CIFS: ignoring forcegid mount option " + "specified with no gid= option.\n"); + return 0; } -- GitLab From 5b05d4696d38c3172e79e855cc1e2ed044589508 Mon Sep 17 00:00:00 2001 From: Michael Buesch Date: Sat, 1 Aug 2009 12:04:19 -0300 Subject: [PATCH 0652/1342] thinkpad-acpi: restrict procfs count value to sane upper limit Signed-off-by: Michael Buesch Acked-by: Henrique de Moraes Holschuh Signed-off-by: Len Brown --- drivers/platform/x86/thinkpad_acpi.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/platform/x86/thinkpad_acpi.c b/drivers/platform/x86/thinkpad_acpi.c index 27d68e719e9..18f9ee63c50 100644 --- a/drivers/platform/x86/thinkpad_acpi.c +++ b/drivers/platform/x86/thinkpad_acpi.c @@ -766,6 +766,8 @@ static int dispatch_procfs_write(struct file *file, if (!ibm || !ibm->write) return -EINVAL; + if (count > PAGE_SIZE - 2) + return -EINVAL; kernbuf = kmalloc(count + 2, GFP_KERNEL); if (!kernbuf) -- GitLab From 59fe4fe34d7afdf63208124f313be9056feaa2f4 Mon Sep 17 00:00:00 2001 From: Henrique de Moraes Holschuh Date: Sat, 1 Aug 2009 12:04:20 -0300 Subject: [PATCH 0653/1342] thinkpad-acpi: fix incorrect use of TPACPI_BRGHT_MODE_ECNVRAM HBRV-based default selection of backlight control strategy didn't work well, at least the X41 defines it but doesn't use it and I don't think it will stop there. Switch to a white/blacklist. All models that have HBRV defined have been included in the list, and initially all ATI GPUs will get ECNVRAM, and the Intel GPUs will get UCMS_STEP. Symptoms of incorrect backlight mode selection are: 1. Non-working backlight control through sysfs; 2. Backlight gets reset to the lowest level at every shutdown, reboot and when thinkpad-acpi gets unloaded; This fixes a regression in 2.6.30, bugzilla #13826 Signed-off-by: Henrique de Moraes Holschuh Reported-by: Tobias Diedrich Cc: stable@kernel.org Signed-off-by: Len Brown --- drivers/platform/x86/thinkpad_acpi.c | 61 +++++++++++++++++++++------- 1 file changed, 47 insertions(+), 14 deletions(-) diff --git a/drivers/platform/x86/thinkpad_acpi.c b/drivers/platform/x86/thinkpad_acpi.c index 18f9ee63c50..e8560085250 100644 --- a/drivers/platform/x86/thinkpad_acpi.c +++ b/drivers/platform/x86/thinkpad_acpi.c @@ -5642,14 +5642,48 @@ static struct backlight_ops ibm_backlight_data = { /* --------------------------------------------------------------------- */ +/* + * These are only useful for models that have only one possibility + * of GPU. If the BIOS model handles both ATI and Intel, don't use + * these quirks. + */ +#define TPACPI_BRGHT_Q_NOEC 0x0001 /* Must NOT use EC HBRV */ +#define TPACPI_BRGHT_Q_EC 0x0002 /* Should or must use EC HBRV */ +#define TPACPI_BRGHT_Q_ASK 0x8000 /* Ask for user report */ + +static const struct tpacpi_quirk brightness_quirk_table[] __initconst = { + /* Models with ATI GPUs known to require ECNVRAM mode */ + TPACPI_Q_IBM('1', 'Y', TPACPI_BRGHT_Q_EC), /* T43/p ATI */ + + /* Models with ATI GPUs (waiting confirmation) */ + TPACPI_Q_IBM('1', 'R', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_EC), + TPACPI_Q_IBM('1', 'Q', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_EC), + TPACPI_Q_IBM('7', '6', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_EC), + TPACPI_Q_IBM('7', '8', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_EC), + + /* Models with Intel Extreme Graphics 2 (waiting confirmation) */ + TPACPI_Q_IBM('1', 'V', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_NOEC), + TPACPI_Q_IBM('1', 'W', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_NOEC), + TPACPI_Q_IBM('1', 'U', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_NOEC), + + /* Models with Intel GMA900 */ + TPACPI_Q_IBM('7', '0', TPACPI_BRGHT_Q_NOEC), /* T43, R52 */ + TPACPI_Q_IBM('7', '4', TPACPI_BRGHT_Q_NOEC), /* X41 */ + TPACPI_Q_IBM('7', '5', TPACPI_BRGHT_Q_NOEC), /* X41 Tablet */ +}; + static int __init brightness_init(struct ibm_init_struct *iibm) { int b; + unsigned long quirks; vdbg_printk(TPACPI_DBG_INIT, "initializing brightness subdriver\n"); mutex_init(&brightness_mutex); + quirks = tpacpi_check_quirks(brightness_quirk_table, + ARRAY_SIZE(brightness_quirk_table)); + /* * We always attempt to detect acpi support, so as to switch * Lenovo Vista BIOS to ACPI brightness mode even if we are not @@ -5706,23 +5740,13 @@ static int __init brightness_init(struct ibm_init_struct *iibm) /* TPACPI_BRGHT_MODE_AUTO not implemented yet, just use default */ if (brightness_mode == TPACPI_BRGHT_MODE_AUTO || brightness_mode == TPACPI_BRGHT_MODE_MAX) { - if (thinkpad_id.vendor == PCI_VENDOR_ID_IBM) { - /* - * IBM models that define HBRV probably have - * EC-based backlight level control - */ - if (acpi_evalf(ec_handle, NULL, "HBRV", "qd")) - /* T40-T43, R50-R52, R50e, R51e, X31-X41 */ - brightness_mode = TPACPI_BRGHT_MODE_ECNVRAM; - else - /* all other IBM ThinkPads */ - brightness_mode = TPACPI_BRGHT_MODE_UCMS_STEP; - } else - /* All Lenovo ThinkPads */ + if (quirks & TPACPI_BRGHT_Q_EC) + brightness_mode = TPACPI_BRGHT_MODE_ECNVRAM; + else brightness_mode = TPACPI_BRGHT_MODE_UCMS_STEP; dbg_printk(TPACPI_DBG_BRGHT, - "selected brightness_mode=%d\n", + "driver auto-selected brightness_mode=%d\n", brightness_mode); } @@ -5749,6 +5773,15 @@ static int __init brightness_init(struct ibm_init_struct *iibm) vdbg_printk(TPACPI_DBG_INIT | TPACPI_DBG_BRGHT, "brightness is supported\n"); + if (quirks & TPACPI_BRGHT_Q_ASK) { + printk(TPACPI_NOTICE + "brightness: will use unverified default: " + "brightness_mode=%d\n", brightness_mode); + printk(TPACPI_NOTICE + "brightness: please report to %s whether it works well " + "or not on your ThinkPad\n", TPACPI_MAIL); + } + ibm_backlight_device->props.max_brightness = (tp_features.bright_16levels)? 15 : 7; ibm_backlight_device->props.brightness = b & TP_EC_BACKLIGHT_LVLMSK; -- GitLab From b4f2e2ad5348063ef94aa623f6f09b52ecaf0990 Mon Sep 17 00:00:00 2001 From: John David Anglin Date: Sun, 2 Aug 2009 12:34:08 +0200 Subject: [PATCH 0654/1342] parisc: Fix GOT overflow during module load on 64bit kernel Signed-off-by: John David Anglin Signed-off-by: Helge Deller --- arch/parisc/kernel/module.c | 50 +++++++++++++++++++++++++++++++++---- 1 file changed, 45 insertions(+), 5 deletions(-) diff --git a/arch/parisc/kernel/module.c b/arch/parisc/kernel/module.c index ef5caf2e6ed..61ee0eec4e6 100644 --- a/arch/parisc/kernel/module.c +++ b/arch/parisc/kernel/module.c @@ -86,8 +86,12 @@ * the bottom of the table, which has a maximum signed displacement of * 0x3fff; however, since we're only going forward, this becomes * 0x1fff, and thus, since each GOT entry is 8 bytes long we can have - * at most 1023 entries */ -#define MAX_GOTS 1023 + * at most 1023 entries. + * To overcome this 14bit displacement with some kernel modules, we'll + * use instead the unusal 16bit displacement method (see reassemble_16a) + * which gives us a maximum positive displacement of 0x7fff, and as such + * allows us to allocate up to 4095 GOT entries. */ +#define MAX_GOTS 4095 /* three functions to determine where in the module core * or init pieces the location is */ @@ -145,12 +149,40 @@ struct stub_entry { /* The reassemble_* functions prepare an immediate value for insertion into an opcode. pa-risc uses all sorts of weird bitfields in the instruction to hold the value. */ +static inline int sign_unext(int x, int len) +{ + int len_ones; + + len_ones = (1 << len) - 1; + return x & len_ones; +} + +static inline int low_sign_unext(int x, int len) +{ + int sign, temp; + + sign = (x >> (len-1)) & 1; + temp = sign_unext(x, len-1); + return (temp << 1) | sign; +} + static inline int reassemble_14(int as14) { return (((as14 & 0x1fff) << 1) | ((as14 & 0x2000) >> 13)); } +static inline int reassemble_16a(int as16) +{ + int s, t; + + /* Unusual 16-bit encoding, for wide mode only. */ + t = (as16 << 1) & 0xffff; + s = (as16 & 0x8000); + return (t ^ s ^ (s >> 1)) | (s >> 15); +} + + static inline int reassemble_17(int as17) { return (((as17 & 0x10000) >> 16) | @@ -407,6 +439,7 @@ static Elf_Addr get_stub(struct module *me, unsigned long value, long addend, enum elf_stub_type stub_type, Elf_Addr loc0, unsigned int targetsec) { struct stub_entry *stub; + int __maybe_unused d; /* initialize stub_offset to point in front of the section */ if (!me->arch.section[targetsec].stub_offset) { @@ -460,12 +493,19 @@ static Elf_Addr get_stub(struct module *me, unsigned long value, long addend, */ switch (stub_type) { case ELF_STUB_GOT: - stub->insns[0] = 0x537b0000; /* ldd 0(%dp),%dp */ + d = get_got(me, value, addend); + if (d <= 15) { + /* Format 5 */ + stub->insns[0] = 0x0f6010db; /* ldd 0(%dp),%dp */ + stub->insns[0] |= low_sign_unext(d, 5) << 16; + } else { + /* Format 3 */ + stub->insns[0] = 0x537b0000; /* ldd 0(%dp),%dp */ + stub->insns[0] |= reassemble_16a(d); + } stub->insns[1] = 0x53610020; /* ldd 10(%dp),%r1 */ stub->insns[2] = 0xe820d000; /* bve (%r1) */ stub->insns[3] = 0x537b0030; /* ldd 18(%dp),%dp */ - - stub->insns[0] |= reassemble_14(get_got(me, value, addend) & 0x3fff); break; case ELF_STUB_MILLI: stub->insns[0] = 0x20200000; /* ldil 0,%r1 */ -- GitLab From 447c233da4d109c6194fefd69e5185cbc93cc062 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Sun, 2 Aug 2009 08:02:28 +0000 Subject: [PATCH 0655/1342] parisc: Fix read buffer overflow in pdc_stable driver Check whether index is within bounds before testing the element. Signed-off-by: Roel Kluin Signed-off-by: Helge Deller --- drivers/parisc/pdc_stable.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/parisc/pdc_stable.c b/drivers/parisc/pdc_stable.c index f9f9a5f1bbd..13a64bc081b 100644 --- a/drivers/parisc/pdc_stable.c +++ b/drivers/parisc/pdc_stable.c @@ -370,7 +370,7 @@ pdcspath_layer_read(struct pdcspath_entry *entry, char *buf) if (!i) /* entry is not ready */ return -ENODATA; - for (i = 0; devpath->layers[i] && (likely(i < 6)); i++) + for (i = 0; i < 6 && devpath->layers[i]; i++) out += sprintf(out, "%u ", devpath->layers[i]); out += sprintf(out, "\n"); -- GitLab From 450d6e306b4717bfae11218a02648509baf04ce1 Mon Sep 17 00:00:00 2001 From: Stoyan Gaydarov Date: Thu, 30 Jul 2009 10:25:19 +0000 Subject: [PATCH 0656/1342] parisc: fixed faulty check in lba_pci This patche fixes a spelling error that has resulted from copy and pasting. The location of the error was found using a semantic patch but the semantic patch was not trying to find these errors. After looking things over it seemed logical that this change was needed. Signed-off-by: Stoyan Gaydarov Signed-off-by: Helge Deller --- drivers/parisc/lba_pci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/parisc/lba_pci.c b/drivers/parisc/lba_pci.c index ede614616f8..3aeb3279c92 100644 --- a/drivers/parisc/lba_pci.c +++ b/drivers/parisc/lba_pci.c @@ -992,7 +992,7 @@ lba_pat_resources(struct parisc_device *pa_dev, struct lba_device *lba_dev) return; io_pdc_cell = kzalloc(sizeof(pdc_pat_cell_mod_maddr_block_t), GFP_KERNEL); - if (!pa_pdc_cell) { + if (!io_pdc_cell) { kfree(pa_pdc_cell); return; } -- GitLab From 6b4dbcd86a9d464057fcc7abe4d0574093071fcc Mon Sep 17 00:00:00 2001 From: Michael Buesch Date: Mon, 20 Jul 2009 22:58:44 +0000 Subject: [PATCH 0657/1342] parisc: isa-eeprom - Fix loff_t usage loff_t is a signed type. If userspace passes a negative ppos, the "count" range check is weakened. "count"s bigger than HPEE_MAX_LENGTH will pass the check. Also, if ppos is negative, the readb(eisa_eeprom_addr + *ppos) will poke in random memory. Signed-off-by: Michael Buesch Cc: stable@kernel.org Signed-off-by: Helge Deller --- drivers/parisc/eisa_eeprom.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/parisc/eisa_eeprom.c b/drivers/parisc/eisa_eeprom.c index 685d94e69d4..8c0b26e9b98 100644 --- a/drivers/parisc/eisa_eeprom.c +++ b/drivers/parisc/eisa_eeprom.c @@ -55,7 +55,7 @@ static ssize_t eisa_eeprom_read(struct file * file, ssize_t ret; int i; - if (*ppos >= HPEE_MAX_LENGTH) + if (*ppos < 0 || *ppos >= HPEE_MAX_LENGTH) return 0; count = *ppos + count < HPEE_MAX_LENGTH ? count : HPEE_MAX_LENGTH - *ppos; -- GitLab From 2678251b207394aa8b9d92c653c05a8b3449f1f5 Mon Sep 17 00:00:00 2001 From: John David Anglin Date: Mon, 13 Jul 2009 01:44:37 +0000 Subject: [PATCH 0658/1342] parisc: Set correct bit in protection flags Signed-off-by: John David Anglin Signed-off-by: Helge Deller --- arch/parisc/kernel/entry.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/parisc/kernel/entry.S b/arch/parisc/kernel/entry.S index ae3e70cd1e1..e552e547cb9 100644 --- a/arch/parisc/kernel/entry.S +++ b/arch/parisc/kernel/entry.S @@ -553,7 +553,7 @@ * on most of those machines only handles cache transactions. */ extrd,u,*= \pte,_PAGE_NO_CACHE_BIT+32,1,%r0 - depi 1,12,1,\prot + depdi 1,12,1,\prot /* Drop prot bits and convert to page addr for iitlbt and idtlbt */ convert_for_tlb_insert20 \pte -- GitLab From b10ff54f9f58adfb708b53e6e56ed3d7804ade74 Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 15:27:20 +0000 Subject: [PATCH 0659/1342] parisc: includecheck fix for ccio-dma.c fix the following 'make includecheck' warning: drivers/parisc/ccio-dma.c: linux/proc_fs.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Signed-off-by: Helge Deller --- drivers/parisc/ccio-dma.c | 1 - 1 file changed, 1 deletion(-) diff --git a/drivers/parisc/ccio-dma.c b/drivers/parisc/ccio-dma.c index 0f0e0b919ef..a45b0c0d574 100644 --- a/drivers/parisc/ccio-dma.c +++ b/drivers/parisc/ccio-dma.c @@ -70,7 +70,6 @@ #undef CCIO_COLLECT_STATS #endif -#include #include /* for proc_runway_root */ #ifdef DEBUG_CCIO_INIT -- GitLab From 470a1396c25c27b4aff08b14d5c9cd9b3da15e09 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Wed, 29 Jul 2009 10:50:09 +0200 Subject: [PATCH 0660/1342] tracing, perf_counter: Add help text to CONFIG_EVENT_PROFILE Explain what tracepoint profiling sources are about. Signed-off-by: Peter Zijlstra Acked-by: Jeff Garzik LKML-Reference: <1248856508.6987.3041.camel@twins> Signed-off-by: Ingo Molnar --- init/Kconfig | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-) diff --git a/init/Kconfig b/init/Kconfig index cb2c0927022..823ee0a2d2a 100644 --- a/init/Kconfig +++ b/init/Kconfig @@ -961,9 +961,17 @@ config PERF_COUNTERS Say Y if unsure. config EVENT_PROFILE - bool "Tracepoint profile sources" + bool "Tracepoint profiling sources" depends on PERF_COUNTERS && EVENT_TRACING default y + help + Allow the use of tracepoints as software performance counters. + + When this is enabled, you can create perf counters based on + tracepoints using PERF_TYPE_TRACEPOINT and the tracepoint ID + found in debugfs://tracing/events/*/*/id. (The -e/--events + option to the perf tool can parse and interpret symbolic + tracepoints, in the subsystem:tracepoint_name format.) endmenu -- GitLab From e53c0994709166b111fbe9162d1a16ece7dfc45b Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Fri, 24 Jul 2009 14:42:10 +0200 Subject: [PATCH 0661/1342] perf_counter: Collapse inherit on read() Currently the counter value returned by read() is the value of the parent counter, to which child counters are only fed back on child exit. Thus read() can return rather erratic (and meaningless) numbers depending on the state of the child processes. Change this by always iterating the full child hierarchy on read() and sum all counters. Suggested-by: Corey Ashford Signed-off-by: Peter Zijlstra LKML-Reference: Signed-off-by: Ingo Molnar --- kernel/perf_counter.c | 14 +++++++++++++- 1 file changed, 13 insertions(+), 1 deletion(-) diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index 95093104195..48471d75ae0 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -1688,6 +1688,18 @@ static int perf_release(struct inode *inode, struct file *file) return 0; } +static u64 perf_counter_read_tree(struct perf_counter *counter) +{ + struct perf_counter *child; + u64 total = 0; + + total += perf_counter_read(counter); + list_for_each_entry(child, &counter->child_list, child_list) + total += perf_counter_read(child); + + return total; +} + /* * Read the performance counter - simple non blocking version for now */ @@ -1707,7 +1719,7 @@ perf_read_hw(struct perf_counter *counter, char __user *buf, size_t count) WARN_ON_ONCE(counter->ctx->parent_ctx); mutex_lock(&counter->child_mutex); - values[0] = perf_counter_read(counter); + values[0] = perf_counter_read_tree(counter); n = 1; if (counter->attr.read_format & PERF_FORMAT_TOTAL_TIME_ENABLED) values[n++] = counter->total_time_enabled + -- GitLab From 9f498cc5be7e013d8d6e4c616980ed0ffc8680d2 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Thu, 23 Jul 2009 14:46:33 +0200 Subject: [PATCH 0662/1342] perf_counter: Full task tracing In order to be able to distinguish between no samples due to inactivity and no samples due to task ended, Arjan asked for PERF_EVENT_EXIT events. This is useful to the boot delay instrumentation (bootchart) app. This patch changes the PERF_EVENT_FORK to be emitted on every clone, and adds PERF_EVENT_EXIT to be emitted on task exit, after the task's counters have been closed. This task tracing is controlled through: attr.comm || attr.mmap and through the new attr.task field. Suggested-by: Arjan van de Ven Cc: Paul Mackerras Cc: Anton Blanchard Signed-off-by: Peter Zijlstra [ cleaned up perf_counter.h a bit ] Signed-off-by: Ingo Molnar --- include/linux/perf_counter.h | 13 +++++- kernel/fork.c | 4 +- kernel/perf_counter.c | 87 ++++++++++++++++++++++++------------ 3 files changed, 71 insertions(+), 33 deletions(-) diff --git a/include/linux/perf_counter.h b/include/linux/perf_counter.h index bd15d7a5f5c..e604e6ef72d 100644 --- a/include/linux/perf_counter.h +++ b/include/linux/perf_counter.h @@ -181,8 +181,9 @@ struct perf_counter_attr { freq : 1, /* use freq, not period */ inherit_stat : 1, /* per task counts */ enable_on_exec : 1, /* next exec enables */ + task : 1, /* trace fork/exit */ - __reserved_1 : 51; + __reserved_1 : 50; __u32 wakeup_events; /* wakeup every n events */ __u32 __reserved_2; @@ -308,6 +309,15 @@ enum perf_event_type { */ PERF_EVENT_COMM = 3, + /* + * struct { + * struct perf_event_header header; + * u32 pid, ppid; + * u32 tid, ptid; + * }; + */ + PERF_EVENT_EXIT = 4, + /* * struct { * struct perf_event_header header; @@ -323,6 +333,7 @@ enum perf_event_type { * struct { * struct perf_event_header header; * u32 pid, ppid; + * u32 tid, ptid; * }; */ PERF_EVENT_FORK = 7, diff --git a/kernel/fork.c b/kernel/fork.c index 29b532e718f..466531eb92c 100644 --- a/kernel/fork.c +++ b/kernel/fork.c @@ -1269,6 +1269,7 @@ static struct task_struct *copy_process(unsigned long clone_flags, write_unlock_irq(&tasklist_lock); proc_fork_connector(p); cgroup_post_fork(p); + perf_counter_fork(p); return p; bad_fork_free_pid: @@ -1410,9 +1411,6 @@ long do_fork(unsigned long clone_flags, init_completion(&vfork); } - if (!(clone_flags & CLONE_THREAD)) - perf_counter_fork(p); - audit_finish_fork(p); tracehook_report_clone(regs, clone_flags, nr, p); diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index 48471d75ae0..199ed477131 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -42,6 +42,7 @@ static int perf_overcommit __read_mostly = 1; static atomic_t nr_counters __read_mostly; static atomic_t nr_mmap_counters __read_mostly; static atomic_t nr_comm_counters __read_mostly; +static atomic_t nr_task_counters __read_mostly; /* * perf counter paranoia level: @@ -1654,6 +1655,8 @@ static void free_counter(struct perf_counter *counter) atomic_dec(&nr_mmap_counters); if (counter->attr.comm) atomic_dec(&nr_comm_counters); + if (counter->attr.task) + atomic_dec(&nr_task_counters); } if (counter->destroy) @@ -2831,10 +2834,12 @@ perf_counter_read_event(struct perf_counter *counter, } /* - * fork tracking + * task tracking -- fork/exit + * + * enabled by: attr.comm | attr.mmap | attr.task */ -struct perf_fork_event { +struct perf_task_event { struct task_struct *task; struct { @@ -2842,37 +2847,42 @@ struct perf_fork_event { u32 pid; u32 ppid; + u32 tid; + u32 ptid; } event; }; -static void perf_counter_fork_output(struct perf_counter *counter, - struct perf_fork_event *fork_event) +static void perf_counter_task_output(struct perf_counter *counter, + struct perf_task_event *task_event) { struct perf_output_handle handle; - int size = fork_event->event.header.size; - struct task_struct *task = fork_event->task; + int size = task_event->event.header.size; + struct task_struct *task = task_event->task; int ret = perf_output_begin(&handle, counter, size, 0, 0); if (ret) return; - fork_event->event.pid = perf_counter_pid(counter, task); - fork_event->event.ppid = perf_counter_pid(counter, task->real_parent); + task_event->event.pid = perf_counter_pid(counter, task); + task_event->event.ppid = perf_counter_pid(counter, task->real_parent); - perf_output_put(&handle, fork_event->event); + task_event->event.tid = perf_counter_tid(counter, task); + task_event->event.ptid = perf_counter_tid(counter, task->real_parent); + + perf_output_put(&handle, task_event->event); perf_output_end(&handle); } -static int perf_counter_fork_match(struct perf_counter *counter) +static int perf_counter_task_match(struct perf_counter *counter) { - if (counter->attr.comm || counter->attr.mmap) + if (counter->attr.comm || counter->attr.mmap || counter->attr.task) return 1; return 0; } -static void perf_counter_fork_ctx(struct perf_counter_context *ctx, - struct perf_fork_event *fork_event) +static void perf_counter_task_ctx(struct perf_counter_context *ctx, + struct perf_task_event *task_event) { struct perf_counter *counter; @@ -2881,19 +2891,19 @@ static void perf_counter_fork_ctx(struct perf_counter_context *ctx, rcu_read_lock(); list_for_each_entry_rcu(counter, &ctx->event_list, event_entry) { - if (perf_counter_fork_match(counter)) - perf_counter_fork_output(counter, fork_event); + if (perf_counter_task_match(counter)) + perf_counter_task_output(counter, task_event); } rcu_read_unlock(); } -static void perf_counter_fork_event(struct perf_fork_event *fork_event) +static void perf_counter_task_event(struct perf_task_event *task_event) { struct perf_cpu_context *cpuctx; struct perf_counter_context *ctx; cpuctx = &get_cpu_var(perf_cpu_context); - perf_counter_fork_ctx(&cpuctx->ctx, fork_event); + perf_counter_task_ctx(&cpuctx->ctx, task_event); put_cpu_var(perf_cpu_context); rcu_read_lock(); @@ -2903,32 +2913,40 @@ static void perf_counter_fork_event(struct perf_fork_event *fork_event) */ ctx = rcu_dereference(current->perf_counter_ctxp); if (ctx) - perf_counter_fork_ctx(ctx, fork_event); + perf_counter_task_ctx(ctx, task_event); rcu_read_unlock(); } -void perf_counter_fork(struct task_struct *task) +static void perf_counter_task(struct task_struct *task, int new) { - struct perf_fork_event fork_event; + struct perf_task_event task_event; if (!atomic_read(&nr_comm_counters) && - !atomic_read(&nr_mmap_counters)) + !atomic_read(&nr_mmap_counters) && + !atomic_read(&nr_task_counters)) return; - fork_event = (struct perf_fork_event){ + task_event = (struct perf_task_event){ .task = task, .event = { .header = { - .type = PERF_EVENT_FORK, + .type = new ? PERF_EVENT_FORK : PERF_EVENT_EXIT, .misc = 0, - .size = sizeof(fork_event.event), + .size = sizeof(task_event.event), }, /* .pid */ /* .ppid */ + /* .tid */ + /* .ptid */ }, }; - perf_counter_fork_event(&fork_event); + perf_counter_task_event(&task_event); +} + +void perf_counter_fork(struct task_struct *task) +{ + perf_counter_task(task, 1); } /* @@ -3887,6 +3905,8 @@ done: atomic_inc(&nr_mmap_counters); if (counter->attr.comm) atomic_inc(&nr_comm_counters); + if (counter->attr.task) + atomic_inc(&nr_task_counters); } return counter; @@ -4248,8 +4268,10 @@ void perf_counter_exit_task(struct task_struct *child) struct perf_counter_context *child_ctx; unsigned long flags; - if (likely(!child->perf_counter_ctxp)) + if (likely(!child->perf_counter_ctxp)) { + perf_counter_task(child, 0); return; + } local_irq_save(flags); /* @@ -4267,15 +4289,22 @@ void perf_counter_exit_task(struct task_struct *child) * incremented the context's refcount before we do put_ctx below. */ spin_lock(&child_ctx->lock); - child->perf_counter_ctxp = NULL; /* * If this context is a clone; unclone it so it can't get * swapped to another process while we're removing all * the counters from it. */ unclone_ctx(child_ctx); - spin_unlock(&child_ctx->lock); - local_irq_restore(flags); + spin_unlock_irqrestore(&child_ctx->lock, flags); + + /* + * Report the task dead after unscheduling the counters so that we + * won't get any samples after PERF_EVENT_EXIT. We can however still + * get a few PERF_EVENT_READ events. + */ + perf_counter_task(child, 0); + + child->perf_counter_ctxp = NULL; /* * We can recurse on the same lock type through: -- GitLab From 27d028de64bd7e1f8e72bdeae6b0586939574fcb Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Thu, 23 Jul 2009 16:52:41 +0200 Subject: [PATCH 0663/1342] perf report: Update for the new FORK/EXIT events Since FORK is now also issued for threads, detect those by comparing the parent and child PID. Teach it about EXIT events and ignore them. Signed-off-by: Peter Zijlstra Cc: Paul Mackerras Signed-off-by: Ingo Molnar --- tools/perf/builtin-report.c | 22 ++++++++++++++++++---- 1 file changed, 18 insertions(+), 4 deletions(-) diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c index b20a4b6e31b..95fd06cdaa9 100644 --- a/tools/perf/builtin-report.c +++ b/tools/perf/builtin-report.c @@ -99,6 +99,7 @@ struct comm_event { struct fork_event { struct perf_event_header header; u32 pid, ppid; + u32 tid, ptid; }; struct lost_event { @@ -1608,15 +1609,27 @@ process_comm_event(event_t *event, unsigned long offset, unsigned long head) } static int -process_fork_event(event_t *event, unsigned long offset, unsigned long head) +process_task_event(event_t *event, unsigned long offset, unsigned long head) { struct thread *thread = threads__findnew(event->fork.pid); struct thread *parent = threads__findnew(event->fork.ppid); - dprintf("%p [%p]: PERF_EVENT_FORK: %d:%d\n", + dprintf("%p [%p]: PERF_EVENT_%s: (%d:%d):(%d:%d)\n", (void *)(offset + head), (void *)(long)(event->header.size), - event->fork.pid, event->fork.ppid); + event->header.type == PERF_EVENT_FORK ? "FORK" : "EXIT", + event->fork.pid, event->fork.tid, + event->fork.ppid, event->fork.ptid); + + /* + * A thread clone will have the same PID for both + * parent and child. + */ + if (thread == parent) + return 0; + + if (event->header.type == PERF_EVENT_EXIT) + return 0; if (!thread || !parent || thread__fork(thread, parent)) { dprintf("problem processing PERF_EVENT_FORK, skipping event.\n"); @@ -1706,7 +1719,8 @@ process_event(event_t *event, unsigned long offset, unsigned long head) return process_comm_event(event, offset, head); case PERF_EVENT_FORK: - return process_fork_event(event, offset, head); + case PERF_EVENT_EXIT: + return process_task_event(event, offset, head); case PERF_EVENT_LOST: return process_lost_event(event, offset, head); -- GitLab From 9b30a26bf3d2c56dcb1c3afaca28b73fcd6ed405 Mon Sep 17 00:00:00 2001 From: Stoyan Gaydarov Date: Thu, 30 Jul 2009 05:25:29 -0500 Subject: [PATCH 0664/1342] perf tools: Fix faulty check This patch fixes a spelling error that has resulted from copy and pasting. The location of the error was found using a semantic patch but the semantic patch was not trying to find these errors. After looking things over it seemed logical that this change was needed. Please review it and then include the patch if it is in fact the correct change. Signed-off-by: Stoyan Gaydarov Signed-off-by: Peter Zijlstra Cc: Mike Galbraith Cc: Paul Mackerras Cc: Arnaldo Carvalho de Melo Cc: Frederic Weisbecker LKML-Reference: <1248949529-20891-1-git-send-email-sgayda2@uiuc.edu> Signed-off-by: Ingo Molnar --- tools/perf/util/symbol.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/tools/perf/util/symbol.c b/tools/perf/util/symbol.c index 28106059bf1..b4fe0579bd6 100644 --- a/tools/perf/util/symbol.c +++ b/tools/perf/util/symbol.c @@ -565,7 +565,7 @@ static int dso__load_sym(struct dso *self, int fd, const char *name, goto out_elf_end; secstrs = elf_getdata(sec_strndx, NULL); - if (symstrs == NULL) + if (secstrs == NULL) goto out_elf_end; nr_syms = shdr.sh_size / shdr.sh_entsize; -- GitLab From 59b9005692d4c8b5d73cfc41aa7229f47be163a9 Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Sun, 26 Jul 2009 19:06:19 -0300 Subject: [PATCH 0665/1342] perf top: Add mwait_idle_with_hints to skip_symbols[] We skip the display of idle routine related symbols because they are typically rather erratic and confusing: they depend on the IRQ rate or sometimes they dominate the profile if they are polling based. Add mwait_idle_with_hints too, this is one of the idle routines on x86. Signed-off-by: Arnaldo Carvalho de Melo Signed-off-by: Ingo Molnar --- tools/perf/builtin-top.c | 1 + 1 file changed, 1 insertion(+) diff --git a/tools/perf/builtin-top.c b/tools/perf/builtin-top.c index c0a423004e1..f139f1ab933 100644 --- a/tools/perf/builtin-top.c +++ b/tools/perf/builtin-top.c @@ -285,6 +285,7 @@ static const char *skip_symbols[] = { "enter_idle", "exit_idle", "mwait_idle", + "mwait_idle_with_hints", "ppc64_runlatch_off", "pseries_dedicated_idle_sleep", NULL -- GitLab From e414314cce7539788dd5d2c35decad11782dd858 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Thu, 23 Jul 2009 20:13:26 +0200 Subject: [PATCH 0666/1342] sched: Fix latencytop and sleep profiling vs group scheduling The latencytop and sleep accounting code assumes that any scheduler entity represents a task, this is not so. Cc: Arjan van de Ven Signed-off-by: Peter Zijlstra Signed-off-by: Ingo Molnar --- kernel/sched_fair.c | 32 +++++++++++++++++++------------- 1 file changed, 19 insertions(+), 13 deletions(-) diff --git a/kernel/sched_fair.c b/kernel/sched_fair.c index 9ffb2b2ceba..652e8bdef9a 100644 --- a/kernel/sched_fair.c +++ b/kernel/sched_fair.c @@ -611,9 +611,13 @@ account_entity_dequeue(struct cfs_rq *cfs_rq, struct sched_entity *se) static void enqueue_sleeper(struct cfs_rq *cfs_rq, struct sched_entity *se) { #ifdef CONFIG_SCHEDSTATS + struct task_struct *tsk = NULL; + + if (entity_is_task(se)) + tsk = task_of(se); + if (se->sleep_start) { u64 delta = rq_of(cfs_rq)->clock - se->sleep_start; - struct task_struct *tsk = task_of(se); if ((s64)delta < 0) delta = 0; @@ -624,11 +628,11 @@ static void enqueue_sleeper(struct cfs_rq *cfs_rq, struct sched_entity *se) se->sleep_start = 0; se->sum_sleep_runtime += delta; - account_scheduler_latency(tsk, delta >> 10, 1); + if (tsk) + account_scheduler_latency(tsk, delta >> 10, 1); } if (se->block_start) { u64 delta = rq_of(cfs_rq)->clock - se->block_start; - struct task_struct *tsk = task_of(se); if ((s64)delta < 0) delta = 0; @@ -639,17 +643,19 @@ static void enqueue_sleeper(struct cfs_rq *cfs_rq, struct sched_entity *se) se->block_start = 0; se->sum_sleep_runtime += delta; - /* - * Blocking time is in units of nanosecs, so shift by 20 to - * get a milliseconds-range estimation of the amount of - * time that the task spent sleeping: - */ - if (unlikely(prof_on == SLEEP_PROFILING)) { - - profile_hits(SLEEP_PROFILING, (void *)get_wchan(tsk), - delta >> 20); + if (tsk) { + /* + * Blocking time is in units of nanosecs, so shift by + * 20 to get a milliseconds-range estimation of the + * amount of time that the task spent sleeping: + */ + if (unlikely(prof_on == SLEEP_PROFILING)) { + profile_hits(SLEEP_PROFILING, + (void *)get_wchan(tsk), + delta >> 20); + } + account_scheduler_latency(tsk, delta >> 10, 0); } - account_scheduler_latency(tsk, delta >> 10, 0); } #endif } -- GitLab From 07903af152b0597d94e9b0030746b63c4664e787 Mon Sep 17 00:00:00 2001 From: Gregory Haskins Date: Thu, 30 Jul 2009 10:57:28 -0400 Subject: [PATCH 0667/1342] sched: Fix race in cpupri introduced by cpumask_var changes Background: Several race conditions in the scheduler have cropped up recently, which Steven and I have tracked down using ftrace. The most recent one turns out to be a race in how the scheduler determines a suitable migration target for RT tasks, introduced recently with commit: commit 68e74568fbe5854952355e942acca51f138096d9 Date: Tue Nov 25 02:35:13 2008 +1030 sched: convert struct cpupri_vec cpumask_var_t. The original design of cpupri allowed lockless readers to quickly determine a best-estimate target. Races between the pri_active bitmap and the vec->mask were handled in the original code because we would detect and return "0" when this occured. The design was predicated on the *effective* atomicity (*) of caching the result of cpus_and() between the cpus_allowed and the vec->mask. Commit 68e74568 changed the behavior such that vec->mask is accessed multiple times. This introduces a subtle race, the result of which means we can have a result that returns "1", but with an empty bitmap. *) yes, we know cpus_and() is not a locked operator across the entire composite array, but it is implicitly atomic on a per-word basis which is all the design required to work. Implementation: Rather than forgoing the lockless design, or reverting to a stack-based cpumask_t, we simply check for when the race has been encountered and continue processing in the event that the race is hit. This renders the removal race as if the priority bit had been atomically cleared as well, and allows the algorithm to execute correctly. Signed-off-by: Gregory Haskins CC: Rusty Russell CC: Steven Rostedt Signed-off-by: Peter Zijlstra LKML-Reference: <20090730145728.25226.92769.stgit@dev.haskins.net> Signed-off-by: Ingo Molnar --- kernel/sched_cpupri.c | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-) diff --git a/kernel/sched_cpupri.c b/kernel/sched_cpupri.c index e6c251790dd..d014efbf947 100644 --- a/kernel/sched_cpupri.c +++ b/kernel/sched_cpupri.c @@ -81,8 +81,21 @@ int cpupri_find(struct cpupri *cp, struct task_struct *p, if (cpumask_any_and(&p->cpus_allowed, vec->mask) >= nr_cpu_ids) continue; - if (lowest_mask) + if (lowest_mask) { cpumask_and(lowest_mask, &p->cpus_allowed, vec->mask); + + /* + * We have to ensure that we have at least one bit + * still set in the array, since the map could have + * been concurrently emptied between the first and + * second reads of vec->mask. If we hit this + * condition, simply act as though we never hit this + * priority level and continue on. + */ + if (cpumask_any(lowest_mask) >= nr_cpu_ids) + continue; + } + return 1; } -- GitLab From c6fe6b0783a8fd923d11dd0388cbd561ff15bdf1 Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Sun, 2 Aug 2009 15:13:29 +0200 Subject: [PATCH 0668/1342] parisc: hp_sdc_mlc.c - check return value of down_trylock() Signed-off-by: Helge Deller --- drivers/input/serio/hp_sdc_mlc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/input/serio/hp_sdc_mlc.c b/drivers/input/serio/hp_sdc_mlc.c index b587e2d576a..820e51673b2 100644 --- a/drivers/input/serio/hp_sdc_mlc.c +++ b/drivers/input/serio/hp_sdc_mlc.c @@ -296,7 +296,7 @@ static void hp_sdc_mlc_out(hil_mlc *mlc) priv->tseq[3] = 0; if (mlc->opacket & HIL_CTRL_APE) { priv->tseq[3] |= HP_SDC_LPC_APE_IPF; - down_trylock(&mlc->csem); + BUG_ON(down_trylock(&mlc->csem)); } enqueue: hp_sdc_enqueue_transaction(&priv->trans); -- GitLab From 1e0deabd35f210f22c03cc734a0335c07ae71ff3 Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Sun, 2 Aug 2009 15:17:37 +0200 Subject: [PATCH 0669/1342] parisc: dino.c - check return value of pci_assign_resource() Signed-off-by: Helge Deller --- drivers/parisc/dino.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/parisc/dino.c b/drivers/parisc/dino.c index c590974e981..d69bde6a234 100644 --- a/drivers/parisc/dino.c +++ b/drivers/parisc/dino.c @@ -614,7 +614,7 @@ dino_fixup_bus(struct pci_bus *bus) dev_name(&bus->self->dev), i, bus->self->resource[i].start, bus->self->resource[i].end); - pci_assign_resource(bus->self, i); + WARN_ON(pci_assign_resource(bus->self, i)); DBG("DEBUG %s after assign %d [0x%lx,0x%lx]\n", dev_name(&bus->self->dev), i, bus->self->resource[i].start, -- GitLab From 01a261e09a21e0ba342d3907a79cf5c78ee3f37a Mon Sep 17 00:00:00 2001 From: Ryusuke Konishi Date: Sun, 2 Aug 2009 17:45:55 +0900 Subject: [PATCH 0670/1342] nilfs2: fix missing unlock in error path of nilfs_mdt_write_page This adds a missing unlock of nilfs->ns_writer_mutex in nilfs_mdt_write_page() function. Signed-off-by: Ryusuke Konishi --- fs/nilfs2/mdt.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/fs/nilfs2/mdt.c b/fs/nilfs2/mdt.c index 3d3ddb3f517..2dfd47714ae 100644 --- a/fs/nilfs2/mdt.c +++ b/fs/nilfs2/mdt.c @@ -412,8 +412,10 @@ nilfs_mdt_write_page(struct page *page, struct writeback_control *wbc) return 0; /* Do not request flush for shadow page cache */ if (!sb) { writer = nilfs_get_writer(NILFS_MDT(inode)->mi_nilfs); - if (!writer) + if (!writer) { + nilfs_put_writer(NILFS_MDT(inode)->mi_nilfs); return -EROFS; + } sb = writer->s_super; } -- GitLab From 1a1dba32412c15c51d5fc0b9efadd2ea310356d7 Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Sun, 2 Aug 2009 15:26:51 +0200 Subject: [PATCH 0671/1342] parisc: sticore.c - check return values Signed-off-by: Helge Deller --- drivers/video/console/sticore.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) diff --git a/drivers/video/console/sticore.c b/drivers/video/console/sticore.c index ef7870f5ea0..857b3668b3b 100644 --- a/drivers/video/console/sticore.c +++ b/drivers/video/console/sticore.c @@ -957,9 +957,14 @@ static int __devinit sticore_pci_init(struct pci_dev *pd, #ifdef CONFIG_PCI unsigned long fb_base, rom_base; unsigned int fb_len, rom_len; + int err; struct sti_struct *sti; - pci_enable_device(pd); + err = pci_enable_device(pd); + if (err < 0) { + dev_err(&pd->dev, "Cannot enable PCI device\n"); + return err; + } fb_base = pci_resource_start(pd, 0); fb_len = pci_resource_len(pd, 0); @@ -1048,7 +1053,7 @@ static void __devinit sti_init_roms(void) /* Register drivers for native & PCI cards */ register_parisc_driver(&pa_sti_driver); - pci_register_driver(&pci_sti_driver); + WARN_ON(pci_register_driver(&pci_sti_driver)); /* if we didn't find the given default sti, take the first one */ if (!default_sti) -- GitLab From c43962321e8af5309dd3ffcd78743c89581265e5 Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Sun, 2 Aug 2009 15:35:43 +0200 Subject: [PATCH 0672/1342] parisc: parisc-agp.c - use correct page_mask function Fix those compiler warnings, which indeed point to a bug: drivers/char/agp/parisc-agp.c:228: warning: initialization from incompatible pointer type drivers/char/agp/parisc-agp.c:201: warning: 'parisc_agp_page_mask_memory' defined but not used Signed-off-by: Helge Deller --- drivers/char/agp/parisc-agp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/char/agp/parisc-agp.c b/drivers/char/agp/parisc-agp.c index f4bb43fb801..e077701ae3d 100644 --- a/drivers/char/agp/parisc-agp.c +++ b/drivers/char/agp/parisc-agp.c @@ -225,7 +225,7 @@ static const struct agp_bridge_driver parisc_agp_driver = { .configure = parisc_agp_configure, .fetch_size = parisc_agp_fetch_size, .tlb_flush = parisc_agp_tlbflush, - .mask_memory = parisc_agp_mask_memory, + .mask_memory = parisc_agp_page_mask_memory, .masks = parisc_agp_masks, .agp_enable = parisc_agp_enable, .cache_flush = global_cache_flush, -- GitLab From cae5a39f34d52c46ca49edfc3f297656a0fd60b7 Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Sun, 2 Aug 2009 15:42:39 +0200 Subject: [PATCH 0673/1342] parisc: hppb.c - fix printk format strings Fix those warnings: drivers/parisc/hppb.c: In function 'hppb_probe': drivers/parisc/hppb.c:65: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'resource_size_t' drivers/parisc/hppb.c:77: warning: format '%08x' expects type 'unsigned int', but argument 3 has type 'resource_size_t' drivers/parisc/hppb.c:77: warning: format '%08x' expects type 'unsigned int', but argument 4 has type 'resource_size_t' Signed-off-by: Helge Deller --- drivers/parisc/hppb.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) diff --git a/drivers/parisc/hppb.c b/drivers/parisc/hppb.c index 13856415b43..815db175d42 100644 --- a/drivers/parisc/hppb.c +++ b/drivers/parisc/hppb.c @@ -62,7 +62,8 @@ static int hppb_probe(struct parisc_device *dev) } card = card->next; } - printk(KERN_INFO "Found GeckoBoa at 0x%x\n", dev->hpa.start); + printk(KERN_INFO "Found GeckoBoa at 0x%llx\n", + (unsigned long long) dev->hpa.start); card->hpa = dev->hpa.start; card->mmio_region.name = "HP-PB Bus"; @@ -73,8 +74,10 @@ static int hppb_probe(struct parisc_device *dev) status = ccio_request_resource(dev, &card->mmio_region); if(status < 0) { - printk(KERN_ERR "%s: failed to claim HP-PB bus space (%08x, %08x)\n", - __FILE__, card->mmio_region.start, card->mmio_region.end); + printk(KERN_ERR "%s: failed to claim HP-PB " + "bus space (0x%08llx, 0x%08llx)\n", + __FILE__, (unsigned long long) card->mmio_region.start, + (unsigned long long) card->mmio_region.end); } return 0; -- GitLab From d0006f3281c920fbfead0f5035c62ec8053f980a Mon Sep 17 00:00:00 2001 From: Len Brown Date: Thu, 30 Jul 2009 16:00:53 -0400 Subject: [PATCH 0674/1342] ACPI: root-only read protection on /sys/firmware/acpi/tables/* they were world readable. Signed-off-by: Len Brown --- drivers/acpi/system.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/acpi/system.c b/drivers/acpi/system.c index 0944daec064..9c61ab2177c 100644 --- a/drivers/acpi/system.c +++ b/drivers/acpi/system.c @@ -121,7 +121,7 @@ static void acpi_table_attr_init(struct acpi_table_attr *table_attr, table_attr->attr.size = 0; table_attr->attr.read = acpi_table_show; table_attr->attr.attr.name = table_attr->name; - table_attr->attr.attr.mode = 0444; + table_attr->attr.attr.mode = 0400; return; } -- GitLab From 74b5820808215f65b70b05a099d6d3c969b82689 Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Wed, 29 Jul 2009 15:54:25 -0600 Subject: [PATCH 0675/1342] ACPI: bind workqueues to CPU 0 to avoid SMI corruption On some machines, a software-initiated SMI causes corruption unless the SMI runs on CPU 0. An SMI can be initiated by any AML, but typically it's done in GPE-related methods that are run via workqueues, so we can avoid the known corruption cases by binding the workqueues to CPU 0. References: http://bugzilla.kernel.org/show_bug.cgi?id=13751 https://bugs.launchpad.net/bugs/157171 https://bugs.launchpad.net/bugs/157691 Signed-off-by: Bjorn Helgaas Signed-off-by: Len Brown --- drivers/acpi/osl.c | 25 +++++++++++++++++++++++++ 1 file changed, 25 insertions(+) diff --git a/drivers/acpi/osl.c b/drivers/acpi/osl.c index 71670719d61..5691f165a95 100644 --- a/drivers/acpi/osl.c +++ b/drivers/acpi/osl.c @@ -189,11 +189,36 @@ acpi_status __init acpi_os_initialize(void) return AE_OK; } +static void bind_to_cpu0(struct work_struct *work) +{ + set_cpus_allowed(current, cpumask_of_cpu(0)); + kfree(work); +} + +static void bind_workqueue(struct workqueue_struct *wq) +{ + struct work_struct *work; + + work = kzalloc(sizeof(struct work_struct), GFP_KERNEL); + INIT_WORK(work, bind_to_cpu0); + queue_work(wq, work); +} + acpi_status acpi_os_initialize1(void) { + /* + * On some machines, a software-initiated SMI causes corruption unless + * the SMI runs on CPU 0. An SMI can be initiated by any AML, but + * typically it's done in GPE-related methods that are run via + * workqueues, so we can avoid the known corruption cases by binding + * the workqueues to CPU 0. + */ kacpid_wq = create_singlethread_workqueue("kacpid"); + bind_workqueue(kacpid_wq); kacpi_notify_wq = create_singlethread_workqueue("kacpi_notify"); + bind_workqueue(kacpi_notify_wq); kacpi_hotplug_wq = create_singlethread_workqueue("kacpi_hotplug"); + bind_workqueue(kacpi_hotplug_wq); BUG_ON(!kacpid_wq); BUG_ON(!kacpi_notify_wq); BUG_ON(!kacpi_hotplug_wq); -- GitLab From aa7b2b2e973874df99a45b31adbed5978b46be1f Mon Sep 17 00:00:00 2001 From: Zhao Yakui Date: Fri, 3 Jul 2009 10:49:03 +0800 Subject: [PATCH 0676/1342] ACPI: Don't treat generic error as ACPI error code in acpi memory hotplug driver Don't treat the generic error as ACPI error code. Otherwise when the generic code is returned, it will complain the following warning messag: >ACPI Exception (acpi_memhotplug-0171): UNKNOWN_STATUS_CODE, Cannot get acpi bus device [20080609] >ACPI: Cannot find driver data > ACPI Error (utglobal-0127): Unknown exception code: 0xFFFFFFED [20080609] > Pid: 85, comm: kacpi_notify Not tainted 2.6.27.19-5-default #1 Call Trace: [] show_trace_log_lvl+0x41/0x58 [] dump_stack+0x69/0x6f ..... At the same time when the generic error code is returned, the ACPI_EXCEPTION is replaced by the printk. Signed-off-by: Zhao Yakui Signed-off-by: Len Brown --- drivers/acpi/acpi_memhotplug.c | 16 ++++++++++------ 1 file changed, 10 insertions(+), 6 deletions(-) diff --git a/drivers/acpi/acpi_memhotplug.c b/drivers/acpi/acpi_memhotplug.c index 7a0f4aa4fa1..37cbe72d17e 100644 --- a/drivers/acpi/acpi_memhotplug.c +++ b/drivers/acpi/acpi_memhotplug.c @@ -38,6 +38,9 @@ #define _COMPONENT ACPI_MEMORY_DEVICE_COMPONENT +#undef PREFIX +#define PREFIX "ACPI:memory_hp:" + ACPI_MODULE_NAME("acpi_memhotplug"); MODULE_AUTHOR("Naveen B S "); MODULE_DESCRIPTION("Hotplug Mem Driver"); @@ -153,6 +156,7 @@ acpi_memory_get_device(acpi_handle handle, acpi_handle phandle; struct acpi_device *device = NULL; struct acpi_device *pdevice = NULL; + int result; if (!acpi_bus_get_device(handle, &device) && device) @@ -165,9 +169,9 @@ acpi_memory_get_device(acpi_handle handle, } /* Get the parent device */ - status = acpi_bus_get_device(phandle, &pdevice); - if (ACPI_FAILURE(status)) { - ACPI_EXCEPTION((AE_INFO, status, "Cannot get acpi bus device")); + result = acpi_bus_get_device(phandle, &pdevice); + if (result) { + printk(KERN_WARNING PREFIX "Cannot get acpi bus device"); return -EINVAL; } @@ -175,9 +179,9 @@ acpi_memory_get_device(acpi_handle handle, * Now add the notified device. This creates the acpi_device * and invokes .add function */ - status = acpi_bus_add(&device, pdevice, handle, ACPI_BUS_TYPE_DEVICE); - if (ACPI_FAILURE(status)) { - ACPI_EXCEPTION((AE_INFO, status, "Cannot add acpi bus")); + result = acpi_bus_add(&device, pdevice, handle, ACPI_BUS_TYPE_DEVICE); + if (result) { + printk(KERN_WARNING PREFIX "Cannot add acpi bus"); return -EINVAL; } -- GitLab From 5d2619fca753d270e63e76c9e18437b0d9bc8d75 Mon Sep 17 00:00:00 2001 From: Zhao Yakui Date: Tue, 7 Jul 2009 10:56:11 +0800 Subject: [PATCH 0677/1342] ACPI: Ingore the memory block with zero block size in course of memory hotplug If the memory block size is zero, ignore it and don't do the memory hotplug flowchart. Otherwise it will complain the following warning message: >System RAM resource 0 - ffffffffffffffff cannot be added Signed-off-by: Zhao Yakui Signed-off-by: Len Brown --- drivers/acpi/acpi_memhotplug.c | 18 +++++++++++++++--- 1 file changed, 15 insertions(+), 3 deletions(-) diff --git a/drivers/acpi/acpi_memhotplug.c b/drivers/acpi/acpi_memhotplug.c index 37cbe72d17e..9a62224cc27 100644 --- a/drivers/acpi/acpi_memhotplug.c +++ b/drivers/acpi/acpi_memhotplug.c @@ -242,7 +242,12 @@ static int acpi_memory_enable_device(struct acpi_memory_device *mem_device) num_enabled++; continue; } - + /* + * If the memory block size is zero, please ignore it. + * Don't try to do the following memory hotplug flowchart. + */ + if (!info->length) + continue; if (node < 0) node = memory_add_physaddr_to_nid(info->start_addr); @@ -257,8 +262,15 @@ static int acpi_memory_enable_device(struct acpi_memory_device *mem_device) mem_device->state = MEMORY_INVALID_STATE; return -EINVAL; } - - return result; + /* + * Sometimes the memory device will contain several memory blocks. + * When one memory block is hot-added to the system memory, it will + * be regarded as a success. + * Otherwise if the last memory block can't be hot-added to the system + * memory, it will be failure and the memory device can't be bound with + * driver. + */ + return 0; } static int acpi_memory_powerdown_device(struct acpi_memory_device *mem_device) -- GitLab From 7334546a52c6764df120459509b1f803a073eacc Mon Sep 17 00:00:00 2001 From: Alan Jenkins Date: Mon, 29 Jun 2009 09:40:07 +0100 Subject: [PATCH 0678/1342] eeepc-laptop: fix hot-unplug on resume OOPS on resume when the wireless adaptor is disabled during suspend was introduced by "eeepc-laptop: read rfkill soft-blocked state on resume". Unable to handle kernel NULL pointer dereference Process s2disk Tainted: G W IP: klist_put Call trace: ? klist_del ? device_del ? device_unregister ? pci_stop_dev ? pci_stop_bus ? pci_remove_device ? eeepc_rfkill_hotplug [eeepc_laptop] ? eeepc_hotk_resume [eeepc_laptop] ? acpi_device_resume ? device_resume ? hibernation_snapshot It appears the PCI device is removed twice. The eeepc_rfkill_hotplug() call from the resume handler is racing against the call from the ACPI notifier callback. The ACPI notification is triggered by the resume handler when it refreshes the value of CM_ASL_WLAN. The fix is to serialize hotplug calls using a workqueue. http://bugzilla.kernel.org/show_bug.cgi?id=13825 Signed-off-by: Alan Jenkins Acked-by: Corentin Chary Signed-off-by: Len Brown --- drivers/platform/x86/eeepc-laptop.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) diff --git a/drivers/platform/x86/eeepc-laptop.c b/drivers/platform/x86/eeepc-laptop.c index ec560f16d72..222ffb892f2 100644 --- a/drivers/platform/x86/eeepc-laptop.c +++ b/drivers/platform/x86/eeepc-laptop.c @@ -143,6 +143,7 @@ struct eeepc_hotk { struct rfkill *bluetooth_rfkill; struct rfkill *wwan3g_rfkill; struct hotplug_slot *hotplug_slot; + struct work_struct hotplug_work; }; /* The actual device the driver binds to */ @@ -660,7 +661,7 @@ static int eeepc_get_adapter_status(struct hotplug_slot *hotplug_slot, return 0; } -static void eeepc_rfkill_hotplug(void) +static void eeepc_hotplug_work(struct work_struct *work) { struct pci_dev *dev; struct pci_bus *bus = pci_find_bus(0, 1); @@ -701,7 +702,7 @@ static void eeepc_rfkill_notify(acpi_handle handle, u32 event, void *data) if (event != ACPI_NOTIFY_BUS_CHECK) return; - eeepc_rfkill_hotplug(); + schedule_work(&ehotk->hotplug_work); } static void eeepc_hotk_notify(struct acpi_device *device, u32 event) @@ -892,7 +893,7 @@ static int eeepc_hotk_resume(struct acpi_device *device) rfkill_set_sw_state(ehotk->wlan_rfkill, wlan != 1); - eeepc_rfkill_hotplug(); + schedule_work(&ehotk->hotplug_work); } if (ehotk->bluetooth_rfkill) @@ -1093,6 +1094,8 @@ static int eeepc_rfkill_init(struct device *dev) { int result = 0; + INIT_WORK(&ehotk->hotplug_work, eeepc_hotplug_work); + eeepc_register_rfkill_notifier("\\_SB.PCI0.P0P6"); eeepc_register_rfkill_notifier("\\_SB.PCI0.P0P7"); -- GitLab From a53a8b56827cc429c6d9f861ad558beeb5f6103f Mon Sep 17 00:00:00 2001 From: Ben McKeegan Date: Tue, 28 Jul 2009 07:43:57 +0000 Subject: [PATCH 0679/1342] ppp: fix lost fragments in ppp_mp_explode() (resubmit) This patch fixes the corner cases where the sum of MTU of the free channels (adjusted for fragmentation overheads) is less than the MTU of PPP link. There are at least 3 situations where this case might arise: - some of the channels are busy - the multilink session is running in a degraded state (i.e. with less than its full complement of active channels) - by design, where multilink protocol is being used to artificially increase the effective link MTU of a single link. Without this patch, at most 1 fragment is ever sent per free channel for a given PPP frame and any remaining part of the PPP frame that does not fit into those fragments is silently discarded. This patch restores the original behaviour which was broken by commit 9c705260feea6ae329bc6b6d5f6d2ef0227eda0a 'ppp:ppp_mp_explode() redesign'. Once all 'free' channels have been given a fragment, an additional fragment is queued to each available channel in turn, as many times as necessary, until the entire PPP frame has been consumed. Signed-off-by: Ben McKeegan Signed-off-by: David S. Miller --- drivers/net/ppp_generic.c | 34 ++++++++++++++++++---------------- 1 file changed, 18 insertions(+), 16 deletions(-) diff --git a/drivers/net/ppp_generic.c b/drivers/net/ppp_generic.c index 639d11bc444..cd37d739ac7 100644 --- a/drivers/net/ppp_generic.c +++ b/drivers/net/ppp_generic.c @@ -1384,7 +1384,7 @@ static int ppp_mp_explode(struct ppp *ppp, struct sk_buff *skb) /* create a fragment for each channel */ bits = B; - while (nfree > 0 && len > 0) { + while (len > 0) { list = list->next; if (list == &ppp->channels) { i = 0; @@ -1431,29 +1431,31 @@ static int ppp_mp_explode(struct ppp *ppp, struct sk_buff *skb) *otherwise divide it according to the speed *of the channel we are going to transmit on */ - if (pch->speed == 0) { - flen = totlen/nfree ; - if (nbigger > 0) { - flen++; - nbigger--; - } - } else { - flen = (((totfree - nzero)*(totlen + hdrlen*totfree)) / - ((totspeed*totfree)/pch->speed)) - hdrlen; - if (nbigger > 0) { - flen += ((totfree - nzero)*pch->speed)/totspeed; - nbigger -= ((totfree - nzero)*pch->speed)/ + if (nfree > 0) { + if (pch->speed == 0) { + flen = totlen/nfree ; + if (nbigger > 0) { + flen++; + nbigger--; + } + } else { + flen = (((totfree - nzero)*(totlen + hdrlen*totfree)) / + ((totspeed*totfree)/pch->speed)) - hdrlen; + if (nbigger > 0) { + flen += ((totfree - nzero)*pch->speed)/totspeed; + nbigger -= ((totfree - nzero)*pch->speed)/ totspeed; + } } + nfree--; } - nfree--; /* *check if we are on the last channel or *we exceded the lenght of the data to *fragment */ - if ((nfree == 0) || (flen > len)) + if ((nfree <= 0) || (flen > len)) flen = len; /* *it is not worth to tx on slow channels: @@ -1467,7 +1469,7 @@ static int ppp_mp_explode(struct ppp *ppp, struct sk_buff *skb) continue; } - mtu = pch->chan->mtu + 2 - hdrlen; + mtu = pch->chan->mtu - hdrlen; if (mtu < 4) mtu = 4; if (flen > mtu) -- GitLab From 446e72f30eca76d6f9a1a54adf84d2c6ba2831f8 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Tue, 28 Jul 2009 03:47:39 +0000 Subject: [PATCH 0680/1342] pppol2tp: calls unregister_pernet_gen_device() at unload time Failure to call unregister_pernet_gen_device() can exhaust memory if module is loaded/unloaded many times. Signed-off-by: Eric Dumazet Acked-by: Cyrill Gorcunov Signed-off-by: David S. Miller --- drivers/net/pppol2tp.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/net/pppol2tp.c b/drivers/net/pppol2tp.c index e7935d09c89..e0f9219a0ae 100644 --- a/drivers/net/pppol2tp.c +++ b/drivers/net/pppol2tp.c @@ -2680,6 +2680,7 @@ out_unregister_pppol2tp_proto: static void __exit pppol2tp_exit(void) { unregister_pppox_proto(PX_PROTO_OL2TP); + unregister_pernet_gen_device(pppol2tp_net_id, &pppol2tp_net_ops); proto_unregister(&pppol2tp_sk_proto); } -- GitLab From 144586301f6af5ae5943a002f030d8c626fa4fdd Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Tue, 28 Jul 2009 02:36:15 +0000 Subject: [PATCH 0681/1342] net: net_assign_generic() fix memcpy() should take into account size of pointers, not only number of pointers to copy. Signed-off-by: Eric Dumazet Acked-by: Pavel Emelyanov Signed-off-by: David S. Miller --- net/core/net_namespace.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/core/net_namespace.c b/net/core/net_namespace.c index b7292a2719d..197283072cc 100644 --- a/net/core/net_namespace.c +++ b/net/core/net_namespace.c @@ -488,7 +488,7 @@ int net_assign_generic(struct net *net, int id, void *data) */ ng->len = id; - memcpy(&ng->ptr, &old_ng->ptr, old_ng->len); + memcpy(&ng->ptr, &old_ng->ptr, old_ng->len * sizeof(void*)); rcu_assign_pointer(net->gen, ng); call_rcu(&old_ng->rcu, net_generic_release); -- GitLab From 1b994b5a1b3cb5395598a08ef3bb0ac118d75c1b Mon Sep 17 00:00:00 2001 From: roel kluin Date: Sat, 1 Aug 2009 20:26:52 +0000 Subject: [PATCH 0682/1342] tulip: Read buffer overflow Check whether index is within bounds before testing the element. Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/tulip/de4x5.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/net/tulip/de4x5.c b/drivers/net/tulip/de4x5.c index eb72d2e9ab3..acfdccd4456 100644 --- a/drivers/net/tulip/de4x5.c +++ b/drivers/net/tulip/de4x5.c @@ -5059,7 +5059,7 @@ mii_get_phy(struct net_device *dev) if ((id == 0) || (id == 65535)) continue; /* Valid ID? */ for (j=0; jphy[k].id && (k < DE4X5_MAX_PHY); k++); + for (k=0; k < DE4X5_MAX_PHY && lp->phy[k].id; k++); if (k < DE4X5_MAX_PHY) { memcpy((char *)&lp->phy[k], (char *)&phy_info[j], sizeof(struct phy_table)); @@ -5072,7 +5072,7 @@ mii_get_phy(struct net_device *dev) break; } if ((j == limit) && (i < DE4X5_MAX_MII)) { - for (k=0; lp->phy[k].id && (k < DE4X5_MAX_PHY); k++); + for (k=0; k < DE4X5_MAX_PHY && lp->phy[k].id; k++); lp->phy[k].addr = i; lp->phy[k].id = id; lp->phy[k].spd.reg = GENERIC_REG; /* ANLPA register */ @@ -5091,7 +5091,7 @@ mii_get_phy(struct net_device *dev) purgatory: lp->active = 0; if (lp->phy[0].id) { /* Reset the PHY devices */ - for (k=0; lp->phy[k].id && (k < DE4X5_MAX_PHY); k++) { /*For each PHY*/ + for (k=0; k < DE4X5_MAX_PHY && lp->phy[k].id; k++) { /*For each PHY*/ mii_wr(MII_CR_RST, MII_CR, lp->phy[k].addr, DE4X5_MII); while (mii_rd(MII_CR, lp->phy[k].addr, DE4X5_MII) & MII_CR_RST); -- GitLab From 54706d99051582993037be5a076aa543fd7f1c38 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Sat, 1 Aug 2009 20:20:13 +0000 Subject: [PATCH 0683/1342] s6gmac: Read buffer overflow Check whether index is within bounds before testing the element. In the last iteration i is PHY_MAX_ADDR. the condition `!(p = pd->mii.bus->phy_map[PHY_MAX_ADDR])' is undefined and may evaluate to false, which leads to a dereference of this invalid phy_map in the phy_connect() below. Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/s6gmac.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/s6gmac.c b/drivers/net/s6gmac.c index 5345e47b35a..4525cbe8dd6 100644 --- a/drivers/net/s6gmac.c +++ b/drivers/net/s6gmac.c @@ -793,7 +793,7 @@ static inline int s6gmac_phy_start(struct net_device *dev) struct s6gmac *pd = netdev_priv(dev); int i = 0; struct phy_device *p = NULL; - while ((!(p = pd->mii.bus->phy_map[i])) && (i < PHY_MAX_ADDR)) + while ((i < PHY_MAX_ADDR) && (!(p = pd->mii.bus->phy_map[i]))) i++; p = phy_connect(dev, dev_name(&p->dev), &s6gmac_adjust_link, 0, PHY_INTERFACE_MODE_RGMII); -- GitLab From 9bfdac94c78faf68ce038d5c45a385927f2667ce Mon Sep 17 00:00:00 2001 From: roel kluin Date: Fri, 31 Jul 2009 03:43:59 +0000 Subject: [PATCH 0684/1342] mISDN: Read buffer overflow Check whether index is within bounds before testing the element. Signed-off-by: Roel Kluin Acked-by: Karsten Keil Signed-off-by: David S. Miller --- drivers/isdn/mISDN/l1oip_core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/isdn/mISDN/l1oip_core.c b/drivers/isdn/mISDN/l1oip_core.c index 990e6a7e667..0ebce046ade 100644 --- a/drivers/isdn/mISDN/l1oip_core.c +++ b/drivers/isdn/mISDN/l1oip_core.c @@ -1480,7 +1480,7 @@ l1oip_init(void) return -ENOMEM; l1oip_cnt = 0; - while (type[l1oip_cnt] && l1oip_cnt < MAX_CARDS) { + while (l1oip_cnt < MAX_CARDS && type[l1oip_cnt]) { switch (type[l1oip_cnt] & 0xff) { case 1: pri = 0; -- GitLab From 50c643e7652458e649955408685a16e88ea6dbae Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Sat, 1 Aug 2009 21:36:16 +0000 Subject: [PATCH 0685/1342] netxen: fix coherent dma mask setting Change default dma mask for NX3031 to 39 bit with ability to update it to 64-bit (if firmware indicates support). Old code was restricting it under 4GB (32-bit), sometimes causing failure to allocate descriptor rings on heavily populated system. NX2031 based NICs will still get 32-bit coherent mask. Signed-off-by: Dhananjay Phadke Signed-off-by: David S. Miller --- drivers/net/netxen/netxen_nic_main.c | 37 +++++++++++++++++++--------- 1 file changed, 25 insertions(+), 12 deletions(-) diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index 637ac8b89ba..3cd8cfcf627 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -221,7 +221,7 @@ netxen_napi_disable(struct netxen_adapter *adapter) } } -static int nx_set_dma_mask(struct netxen_adapter *adapter, uint8_t revision_id) +static int nx_set_dma_mask(struct netxen_adapter *adapter) { struct pci_dev *pdev = adapter->pdev; uint64_t mask, cmask; @@ -229,19 +229,17 @@ static int nx_set_dma_mask(struct netxen_adapter *adapter, uint8_t revision_id) adapter->pci_using_dac = 0; mask = DMA_BIT_MASK(32); - /* - * Consistent DMA mask is set to 32 bit because it cannot be set to - * 35 bits. For P3 also leave it at 32 bits for now. Only the rings - * come off this pool. - */ cmask = DMA_BIT_MASK(32); + if (NX_IS_REVISION_P2(adapter->ahw.revision_id)) { #ifndef CONFIG_IA64 - if (revision_id >= NX_P3_B0) - mask = DMA_BIT_MASK(39); - else if (revision_id == NX_P2_C1) mask = DMA_BIT_MASK(35); #endif + } else { + mask = DMA_BIT_MASK(39); + cmask = mask; + } + if (pci_set_dma_mask(pdev, mask) == 0 && pci_set_consistent_dma_mask(pdev, cmask) == 0) { adapter->pci_using_dac = 1; @@ -256,7 +254,7 @@ static int nx_update_dma_mask(struct netxen_adapter *adapter) { int change, shift, err; - uint64_t mask, old_mask; + uint64_t mask, old_mask, old_cmask; struct pci_dev *pdev = adapter->pdev; change = 0; @@ -272,14 +270,29 @@ nx_update_dma_mask(struct netxen_adapter *adapter) if (change) { old_mask = pdev->dma_mask; + old_cmask = pdev->dev.coherent_dma_mask; + mask = (1ULL<<(32+shift)) - 1; err = pci_set_dma_mask(pdev, mask); if (err) - return pci_set_dma_mask(pdev, old_mask); + goto err_out; + + if (NX_IS_REVISION_P3(adapter->ahw.revision_id)) { + + err = pci_set_consistent_dma_mask(pdev, mask); + if (err) + goto err_out; + } + dev_info(&pdev->dev, "using %d-bit dma mask\n", 32+shift); } return 0; + +err_out: + pci_set_dma_mask(pdev, old_mask); + pci_set_consistent_dma_mask(pdev, old_cmask); + return err; } static void netxen_check_options(struct netxen_adapter *adapter) @@ -1006,7 +1019,7 @@ netxen_nic_probe(struct pci_dev *pdev, const struct pci_device_id *ent) revision_id = pdev->revision; adapter->ahw.revision_id = revision_id; - err = nx_set_dma_mask(adapter, revision_id); + err = nx_set_dma_mask(adapter); if (err) goto err_out_free_netdev; -- GitLab From a6ac65db2329e7685299666f5f7b6093c7b0f3a0 Mon Sep 17 00:00:00 2001 From: Jiri Pirko Date: Thu, 30 Jul 2009 01:06:12 +0000 Subject: [PATCH 0686/1342] net: restore the original spinlock to protect unicast list There is a path when an assetion in dev_unicast_sync() appears. igmp6_group_added -> dev_mc_add -> __dev_set_rx_mode -> -> vlan_dev_set_rx_mode -> dev_unicast_sync Therefore we cannot protect this list with rtnl. This patch restores the original protecting this list with spinlock. Signed-off-by: Jiri Pirko Tested-by: Meelis Roos Signed-off-by: David S. Miller --- net/core/dev.c | 25 ++++++++++++++++--------- 1 file changed, 16 insertions(+), 9 deletions(-) diff --git a/net/core/dev.c b/net/core/dev.c index 70c27e0c7c3..43e61ba7bd9 100644 --- a/net/core/dev.c +++ b/net/core/dev.c @@ -3865,10 +3865,12 @@ int dev_unicast_delete(struct net_device *dev, void *addr) ASSERT_RTNL(); + netif_addr_lock_bh(dev); err = __hw_addr_del(&dev->uc, addr, dev->addr_len, NETDEV_HW_ADDR_T_UNICAST); if (!err) __dev_set_rx_mode(dev); + netif_addr_unlock_bh(dev); return err; } EXPORT_SYMBOL(dev_unicast_delete); @@ -3889,10 +3891,12 @@ int dev_unicast_add(struct net_device *dev, void *addr) ASSERT_RTNL(); + netif_addr_lock_bh(dev); err = __hw_addr_add(&dev->uc, addr, dev->addr_len, NETDEV_HW_ADDR_T_UNICAST); if (!err) __dev_set_rx_mode(dev); + netif_addr_unlock_bh(dev); return err; } EXPORT_SYMBOL(dev_unicast_add); @@ -3949,7 +3953,8 @@ void __dev_addr_unsync(struct dev_addr_list **to, int *to_count, * @from: source device * * Add newly added addresses to the destination device and release - * addresses that have no users left. + * addresses that have no users left. The source device must be + * locked by netif_tx_lock_bh. * * This function is intended to be called from the dev->set_rx_mode * function of layered software devices. @@ -3958,14 +3963,14 @@ int dev_unicast_sync(struct net_device *to, struct net_device *from) { int err = 0; - ASSERT_RTNL(); - if (to->addr_len != from->addr_len) return -EINVAL; + netif_addr_lock_bh(to); err = __hw_addr_sync(&to->uc, &from->uc, to->addr_len); if (!err) __dev_set_rx_mode(to); + netif_addr_unlock_bh(to); return err; } EXPORT_SYMBOL(dev_unicast_sync); @@ -3981,28 +3986,30 @@ EXPORT_SYMBOL(dev_unicast_sync); */ void dev_unicast_unsync(struct net_device *to, struct net_device *from) { - ASSERT_RTNL(); - if (to->addr_len != from->addr_len) return; + netif_addr_lock_bh(from); + netif_addr_lock(to); __hw_addr_unsync(&to->uc, &from->uc, to->addr_len); __dev_set_rx_mode(to); + netif_addr_unlock(to); + netif_addr_unlock_bh(from); } EXPORT_SYMBOL(dev_unicast_unsync); static void dev_unicast_flush(struct net_device *dev) { - /* rtnl_mutex must be held here */ - + netif_addr_lock_bh(dev); __hw_addr_flush(&dev->uc); + netif_addr_unlock_bh(dev); } static void dev_unicast_init(struct net_device *dev) { - /* rtnl_mutex must be held here */ - + netif_addr_lock_bh(dev); __hw_addr_init(&dev->uc); + netif_addr_unlock_bh(dev); } -- GitLab From df4e7f72f5156ef16a918da8a575ba90ec27ab77 Mon Sep 17 00:00:00 2001 From: Don Fry Date: Fri, 31 Jul 2009 08:40:06 +0000 Subject: [PATCH 0687/1342] pcnet32: remove superfluous NULL pointer check in pcnet32_probe1() Move the debug printk() into the proper place and remove superfluous NULL pointer check in pcnet32_probe1(). This takes care of the following entry from Dan's list: drivers/net/pcnet32.c +1889 pcnet32_probe1(298) warning: variable derefenced before check 'pdev' Reported-by: Dan Carpenter Signed-off-by: Bartlomiej Zolnierkiewicz Acked-by: Don Fry Signed-off-by: David S. Miller --- drivers/net/pcnet32.c | 18 +++++++----------- 1 file changed, 7 insertions(+), 11 deletions(-) diff --git a/drivers/net/pcnet32.c b/drivers/net/pcnet32.c index 1c35e1d637a..b61c97254b3 100644 --- a/drivers/net/pcnet32.c +++ b/drivers/net/pcnet32.c @@ -1611,8 +1611,11 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) if (pcnet32_dwio_read_csr(ioaddr, 0) == 4 && pcnet32_dwio_check(ioaddr)) { a = &pcnet32_dwio; - } else + } else { + if (pcnet32_debug & NETIF_MSG_PROBE) + printk(KERN_ERR PFX "No access methods\n"); goto err_release_region; + } } chip_version = @@ -1852,12 +1855,6 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) ((cards_found >= MAX_UNITS) || full_duplex[cards_found])) lp->options |= PCNET32_PORT_FD; - if (!a) { - if (pcnet32_debug & NETIF_MSG_PROBE) - printk(KERN_ERR PFX "No access methods\n"); - ret = -ENODEV; - goto err_free_consistent; - } lp->a = *a; /* prior to register_netdev, dev->name is not yet correct */ @@ -1973,14 +1970,13 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) return 0; - err_free_ring: +err_free_ring: pcnet32_free_ring(dev); - err_free_consistent: pci_free_consistent(lp->pci_dev, sizeof(*lp->init_block), lp->init_block, lp->init_dma_addr); - err_free_netdev: +err_free_netdev: free_netdev(dev); - err_release_region: +err_release_region: release_region(ioaddr, PCNET32_TOTAL_SIZE); return ret; } -- GitLab From 63097b3ad85788a64c75091bff351ecc850761b2 Mon Sep 17 00:00:00 2001 From: Don Fry Date: Fri, 31 Jul 2009 08:45:29 +0000 Subject: [PATCH 0688/1342] pcnet32: VLB support fixes VLB support has been broken since at least 2004-2005 period as some changes introduced back then assumed that ->pci_dev is always valid, lets try to fix it: - remove duplicated SET_NETDEV_DEV() call - call SET_NETDEV_DEV() only for PCI devices - check for ->pci_dev validity in pcnet32_open() [ Alternatively we may consider removing VLB support but there would not be much gain in it since an extra driver code needed for VLB support is minimal and quite simple. ] This takes care of the following entry from Dan's list: drivers/net/pcnet32.c +1889 pcnet32_probe1(298) warning: variable derefenced before check 'pdev' Reported-by: Dan Carpenter Signed-off-by: Bartlomiej Zolnierkiewicz Acked-by: Don Fry Signed-off-by: David S. Miller --- drivers/net/pcnet32.c | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-) diff --git a/drivers/net/pcnet32.c b/drivers/net/pcnet32.c index b61c97254b3..16964ec73e6 100644 --- a/drivers/net/pcnet32.c +++ b/drivers/net/pcnet32.c @@ -1722,7 +1722,9 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) ret = -ENOMEM; goto err_release_region; } - SET_NETDEV_DEV(dev, &pdev->dev); + + if (pdev) + SET_NETDEV_DEV(dev, &pdev->dev); if (pcnet32_debug & NETIF_MSG_PROBE) printk(KERN_INFO PFX "%s at %#3lx,", chipname, ioaddr); @@ -1821,7 +1823,6 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) spin_lock_init(&lp->lock); - SET_NETDEV_DEV(dev, &pdev->dev); lp->name = chipname; lp->shared_irq = shared; lp->tx_ring_size = TX_RING_SIZE; /* default tx ring size */ @@ -2085,6 +2086,7 @@ static void pcnet32_free_ring(struct net_device *dev) static int pcnet32_open(struct net_device *dev) { struct pcnet32_private *lp = netdev_priv(dev); + struct pci_dev *pdev = lp->pci_dev; unsigned long ioaddr = dev->base_addr; u16 val; int i; @@ -2145,9 +2147,9 @@ static int pcnet32_open(struct net_device *dev) lp->a.write_csr(ioaddr, 124, val); /* Allied Telesyn AT 2700/2701 FX are 100Mbit only and do not negotiate */ - if (lp->pci_dev->subsystem_vendor == PCI_VENDOR_ID_AT && - (lp->pci_dev->subsystem_device == PCI_SUBDEVICE_ID_AT_2700FX || - lp->pci_dev->subsystem_device == PCI_SUBDEVICE_ID_AT_2701FX)) { + if (pdev && pdev->subsystem_vendor == PCI_VENDOR_ID_AT && + (pdev->subsystem_device == PCI_SUBDEVICE_ID_AT_2700FX || + pdev->subsystem_device == PCI_SUBDEVICE_ID_AT_2701FX)) { if (lp->options & PCNET32_PORT_ASEL) { lp->options = PCNET32_PORT_FD | PCNET32_PORT_100; if (netif_msg_link(lp)) -- GitLab From 5973bee46fe66db94fab198979dec87f263fc2a8 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Tue, 21 Jul 2009 00:40:46 +0200 Subject: [PATCH 0689/1342] [WATCHDOG] Fix COH 901 327 watchdog enablement Since the COH 901 327 found in U300 is clocked at 32 kHz we need to wait for the interrupt clearing flag to propagate through hardware in order not to accidentally fire off any interrupts when we enable them. Signed-off-by: Linus Walleij Signed-off-by: Wim Van Sebroeck --- drivers/watchdog/coh901327_wdt.c | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/drivers/watchdog/coh901327_wdt.c b/drivers/watchdog/coh901327_wdt.c index fecb307d28e..aec7cefdef2 100644 --- a/drivers/watchdog/coh901327_wdt.c +++ b/drivers/watchdog/coh901327_wdt.c @@ -18,6 +18,7 @@ #include #include #include +#include #define DRV_NAME "WDOG COH 901 327" @@ -92,6 +93,8 @@ static struct clk *clk; static void coh901327_enable(u16 timeout) { u16 val; + unsigned long freq; + unsigned long delay_ns; clk_enable(clk); /* Restart timer if it is disabled */ @@ -102,6 +105,14 @@ static void coh901327_enable(u16 timeout) /* Acknowledge any pending interrupt so it doesn't just fire off */ writew(U300_WDOG_IER_WILL_BARK_IRQ_ACK_ENABLE, virtbase + U300_WDOG_IER); + /* + * The interrupt is cleared in the 32 kHz clock domain. + * Wait 3 32 kHz cycles for it to take effect + */ + freq = clk_get_rate(clk); + delay_ns = (1000000000 + freq - 1) / freq; /* Freq to ns and round up */ + delay_ns = 3 * delay_ns; /* Wait 3 cycles */ + ndelay(delay_ns); /* Enable the watchdog interrupt */ writew(U300_WDOG_IMR_WILL_BARK_IRQ_ENABLE, virtbase + U300_WDOG_IMR); /* Activate the watchdog timer */ -- GitLab From b564afcfb82fe3e63a7ce05a944eb5e11244d7cb Mon Sep 17 00:00:00 2001 From: Andreas Eversberg Date: Mon, 27 Jul 2009 07:24:04 +0000 Subject: [PATCH 0690/1342] mISDN: Fix handling of receive buffer size in L1oIP The size of receive buffer pointer was used to get size of receive buffer instead of recvbuf_size itself, so only 4/8 bytes could be transfered. This is a regression to 2.6.30 introduced by commit 8c90e11e3543d7de612194a042a148caeaab5f1d mISDN: Use kernel_{send,recv}msg instead of open coding Signed-off-by: Andreas Eversberg Signed-off-by: Karsten Keil Signed-off-by: David S. Miller --- drivers/isdn/mISDN/l1oip_core.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/isdn/mISDN/l1oip_core.c b/drivers/isdn/mISDN/l1oip_core.c index 0ebce046ade..7e5f30dbc0a 100644 --- a/drivers/isdn/mISDN/l1oip_core.c +++ b/drivers/isdn/mISDN/l1oip_core.c @@ -731,10 +731,10 @@ l1oip_socket_thread(void *data) while (!signal_pending(current)) { struct kvec iov = { .iov_base = recvbuf, - .iov_len = sizeof(recvbuf), + .iov_len = recvbuf_size, }; recvlen = kernel_recvmsg(socket, &msg, &iov, 1, - sizeof(recvbuf), 0); + recvbuf_size, 0); if (recvlen > 0) { l1oip_socket_parse(hc, &sin_rx, recvbuf, recvlen); } else { -- GitLab From 79896cf42f6a96d7e14f2dc3473443d68d74031d Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sun, 2 Aug 2009 14:04:19 -0700 Subject: [PATCH 0691/1342] Make pci_claim_resource() use request_resource() rather than insert_resource() This function has traditionally used "insert_resource()", because before commit cebd78a8c5 ("Fix pci_claim_resource") it used to just insert the resource into whatever root resource tree that was indicated by "pcibios_select_root()". So there Matthew fixed it to actually look up the proper parent resource, which means that now it's actively wrong to then traverse the resource tree any more: we already know exactly where the new resource should go. And when we then did commit a76117dfd6 ("x86: Use pci_claim_resource"), which changed the x86 PCI code from the open-coded pr = pci_find_parent_resource(dev, r); if (!pr || request_resource(pr, r) < 0) { to using if (pci_claim_resource(dev, idx) < 0) { that "insert_resource()" now suddenly became a problem, and causes a regression covered by http://bugzilla.kernel.org/show_bug.cgi?id=13891 which this fixes. Reported-and-tested-by: Rafael J. Wysocki Cc: Matthew Wilcox Cc: Andrew Patterson Cc: Linux PCI Signed-off-by: Linus Torvalds --- drivers/pci/setup-res.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/pci/setup-res.c b/drivers/pci/setup-res.c index b711fb7181e..1898c7b4790 100644 --- a/drivers/pci/setup-res.c +++ b/drivers/pci/setup-res.c @@ -100,16 +100,16 @@ int pci_claim_resource(struct pci_dev *dev, int resource) { struct resource *res = &dev->resource[resource]; struct resource *root; - char *dtype = resource < PCI_BRIDGE_RESOURCES ? "device" : "bridge"; int err; root = pci_find_parent_resource(dev, res); err = -EINVAL; if (root != NULL) - err = insert_resource(root, res); + err = request_resource(root, res); if (err) { + const char *dtype = resource < PCI_BRIDGE_RESOURCES ? "device" : "bridge"; dev_err(&dev->dev, "BAR %d: %s of %s %pR\n", resource, root ? "address space collision on" : -- GitLab From 57d7f282271a83fe4ca4bd15eee79be577210210 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Fri, 31 Jul 2009 21:28:16 -0700 Subject: [PATCH 0692/1342] TTY: Maintainer change Clearly, I am a glutton for punishment. I'll see if I can see Alan's changes through to the end, otherwise I'll be fending off a lot of bug reports for usb-serial devices. Cc: Alan Cox Signed-off-by: Greg Kroah-Hartman Signed-off-by: Linus Torvalds --- MAINTAINERS | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/MAINTAINERS b/MAINTAINERS index d6befb2c470..b1114cfac6b 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -4995,7 +4995,9 @@ T: git git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial.git S: Maintained TTY LAYER -S: Orphan +M: Greg Kroah-Hartman +S: Maintained +T: quilt kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/ F: drivers/char/tty_* F: drivers/serial/serial_core.c F: include/linux/serial_core.h -- GitLab From ac5e7113e74872928844d00085bd47c988f12728 Mon Sep 17 00:00:00 2001 From: Andre Noll Date: Mon, 3 Aug 2009 10:59:47 +1000 Subject: [PATCH 0693/1342] md: Push down data integrity code to personalities. This patch replaces md_integrity_check() by two new public functions: md_integrity_register() and md_integrity_add_rdev() which are both personality-independent. md_integrity_register() is called from the ->run and ->hot_remove methods of all personalities that support data integrity. The function iterates over the component devices of the array and determines if all active devices are integrity capable and if their profiles match. If this is the case, the common profile is registered for the mddev via blk_integrity_register(). The second new function, md_integrity_add_rdev() is called from the ->hot_add_disk methods, i.e. whenever a new device is being added to a raid array. If the new device does not support data integrity, or has a profile different from the one already registered, data integrity for the mddev is disabled. For raid0 and linear, only the call to md_integrity_register() from the ->run method is necessary. Signed-off-by: Andre Noll Signed-off-by: NeilBrown --- drivers/md/linear.c | 1 + drivers/md/md.c | 94 ++++++++++++++++++++++++++++-------------- drivers/md/md.h | 2 + drivers/md/multipath.c | 5 ++- drivers/md/raid0.c | 1 + drivers/md/raid1.c | 6 ++- drivers/md/raid10.c | 4 ++ 7 files changed, 80 insertions(+), 33 deletions(-) diff --git a/drivers/md/linear.c b/drivers/md/linear.c index 5810fa906af..54c8677f1e5 100644 --- a/drivers/md/linear.c +++ b/drivers/md/linear.c @@ -220,6 +220,7 @@ static int linear_run (mddev_t *mddev) mddev->queue->unplug_fn = linear_unplug; mddev->queue->backing_dev_info.congested_fn = linear_congested; mddev->queue->backing_dev_info.congested_data = mddev; + md_integrity_register(mddev); return 0; } diff --git a/drivers/md/md.c b/drivers/md/md.c index d4351ff0849..180949e94a7 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -1487,37 +1487,76 @@ static int match_mddev_units(mddev_t *mddev1, mddev_t *mddev2) static LIST_HEAD(pending_raid_disks); -static void md_integrity_check(mdk_rdev_t *rdev, mddev_t *mddev) +/* + * Try to register data integrity profile for an mddev + * + * This is called when an array is started and after a disk has been kicked + * from the array. It only succeeds if all working and active component devices + * are integrity capable with matching profiles. + */ +int md_integrity_register(mddev_t *mddev) +{ + mdk_rdev_t *rdev, *reference = NULL; + + if (list_empty(&mddev->disks)) + return 0; /* nothing to do */ + if (blk_get_integrity(mddev->gendisk)) + return 0; /* already registered */ + list_for_each_entry(rdev, &mddev->disks, same_set) { + /* skip spares and non-functional disks */ + if (test_bit(Faulty, &rdev->flags)) + continue; + if (rdev->raid_disk < 0) + continue; + /* + * If at least one rdev is not integrity capable, we can not + * enable data integrity for the md device. + */ + if (!bdev_get_integrity(rdev->bdev)) + return -EINVAL; + if (!reference) { + /* Use the first rdev as the reference */ + reference = rdev; + continue; + } + /* does this rdev's profile match the reference profile? */ + if (blk_integrity_compare(reference->bdev->bd_disk, + rdev->bdev->bd_disk) < 0) + return -EINVAL; + } + /* + * All component devices are integrity capable and have matching + * profiles, register the common profile for the md device. + */ + if (blk_integrity_register(mddev->gendisk, + bdev_get_integrity(reference->bdev)) != 0) { + printk(KERN_ERR "md: failed to register integrity for %s\n", + mdname(mddev)); + return -EINVAL; + } + printk(KERN_NOTICE "md: data integrity on %s enabled\n", + mdname(mddev)); + return 0; +} +EXPORT_SYMBOL(md_integrity_register); + +/* Disable data integrity if non-capable/non-matching disk is being added */ +void md_integrity_add_rdev(mdk_rdev_t *rdev, mddev_t *mddev) { - struct mdk_personality *pers = mddev->pers; - struct gendisk *disk = mddev->gendisk; struct blk_integrity *bi_rdev = bdev_get_integrity(rdev->bdev); - struct blk_integrity *bi_mddev = blk_get_integrity(disk); + struct blk_integrity *bi_mddev = blk_get_integrity(mddev->gendisk); - /* Data integrity passthrough not supported on RAID 4, 5 and 6 */ - if (pers && pers->level >= 4 && pers->level <= 6) + if (!bi_mddev) /* nothing to do */ return; - - /* If rdev is integrity capable, register profile for mddev */ - if (!bi_mddev && bi_rdev) { - if (blk_integrity_register(disk, bi_rdev)) - printk(KERN_ERR "%s: %s Could not register integrity!\n", - __func__, disk->disk_name); - else - printk(KERN_NOTICE "Enabling data integrity on %s\n", - disk->disk_name); + if (rdev->raid_disk < 0) /* skip spares */ return; - } - - /* Check that mddev and rdev have matching profiles */ - if (blk_integrity_compare(disk, rdev->bdev->bd_disk) < 0) { - printk(KERN_ERR "%s: %s/%s integrity mismatch!\n", __func__, - disk->disk_name, rdev->bdev->bd_disk->disk_name); - printk(KERN_NOTICE "Disabling data integrity on %s\n", - disk->disk_name); - blk_integrity_unregister(disk); - } + if (bi_rdev && blk_integrity_compare(mddev->gendisk, + rdev->bdev->bd_disk) >= 0) + return; + printk(KERN_NOTICE "disabling data integrity on %s\n", mdname(mddev)); + blk_integrity_unregister(mddev->gendisk); } +EXPORT_SYMBOL(md_integrity_add_rdev); static int bind_rdev_to_array(mdk_rdev_t * rdev, mddev_t * mddev) { @@ -1591,7 +1630,6 @@ static int bind_rdev_to_array(mdk_rdev_t * rdev, mddev_t * mddev) /* May as well allow recovery to be retried once */ mddev->recovery_disabled = 0; - md_integrity_check(rdev, mddev); return 0; fail: @@ -4048,10 +4086,6 @@ static int do_md_run(mddev_t * mddev) } strlcpy(mddev->clevel, pers->name, sizeof(mddev->clevel)); - if (pers->level >= 4 && pers->level <= 6) - /* Cannot support integrity (yet) */ - blk_integrity_unregister(mddev->gendisk); - if (mddev->reshape_position != MaxSector && pers->start_reshape == NULL) { /* This personality cannot handle reshaping... */ diff --git a/drivers/md/md.h b/drivers/md/md.h index 9430a110db9..78f03168baf 100644 --- a/drivers/md/md.h +++ b/drivers/md/md.h @@ -431,5 +431,7 @@ extern int md_allow_write(mddev_t *mddev); extern void md_wait_for_blocked_rdev(mdk_rdev_t *rdev, mddev_t *mddev); extern void md_set_array_sectors(mddev_t *mddev, sector_t array_sectors); extern int md_check_no_bitmap(mddev_t *mddev); +extern int md_integrity_register(mddev_t *mddev); +void md_integrity_add_rdev(mdk_rdev_t *rdev, mddev_t *mddev); #endif /* _MD_MD_H */ diff --git a/drivers/md/multipath.c b/drivers/md/multipath.c index 237fe3fd235..7140909f666 100644 --- a/drivers/md/multipath.c +++ b/drivers/md/multipath.c @@ -313,6 +313,7 @@ static int multipath_add_disk(mddev_t *mddev, mdk_rdev_t *rdev) set_bit(In_sync, &rdev->flags); rcu_assign_pointer(p->rdev, rdev); err = 0; + md_integrity_add_rdev(rdev, mddev); break; } @@ -345,7 +346,9 @@ static int multipath_remove_disk(mddev_t *mddev, int number) /* lost the race, try later */ err = -EBUSY; p->rdev = rdev; + goto abort; } + md_integrity_register(mddev); } abort: @@ -519,7 +522,7 @@ static int multipath_run (mddev_t *mddev) mddev->queue->unplug_fn = multipath_unplug; mddev->queue->backing_dev_info.congested_fn = multipath_congested; mddev->queue->backing_dev_info.congested_data = mddev; - + md_integrity_register(mddev); return 0; out_free_conf: diff --git a/drivers/md/raid0.c b/drivers/md/raid0.c index 335f490dcad..898e2bdfee4 100644 --- a/drivers/md/raid0.c +++ b/drivers/md/raid0.c @@ -351,6 +351,7 @@ static int raid0_run(mddev_t *mddev) blk_queue_merge_bvec(mddev->queue, raid0_mergeable_bvec); dump_zones(mddev); + md_integrity_register(mddev); return 0; } diff --git a/drivers/md/raid1.c b/drivers/md/raid1.c index 0569efba0c0..67e794d0097 100644 --- a/drivers/md/raid1.c +++ b/drivers/md/raid1.c @@ -1144,7 +1144,7 @@ static int raid1_add_disk(mddev_t *mddev, mdk_rdev_t *rdev) rcu_assign_pointer(p->rdev, rdev); break; } - + md_integrity_add_rdev(rdev, mddev); print_conf(conf); return err; } @@ -1178,7 +1178,9 @@ static int raid1_remove_disk(mddev_t *mddev, int number) /* lost the race, try later */ err = -EBUSY; p->rdev = rdev; + goto abort; } + md_integrity_register(mddev); } abort: @@ -2067,7 +2069,7 @@ static int run(mddev_t *mddev) mddev->queue->unplug_fn = raid1_unplug; mddev->queue->backing_dev_info.congested_fn = raid1_congested; mddev->queue->backing_dev_info.congested_data = mddev; - + md_integrity_register(mddev); return 0; out_no_mem: diff --git a/drivers/md/raid10.c b/drivers/md/raid10.c index 7298a5e5a18..3d9020cf6f6 100644 --- a/drivers/md/raid10.c +++ b/drivers/md/raid10.c @@ -1170,6 +1170,7 @@ static int raid10_add_disk(mddev_t *mddev, mdk_rdev_t *rdev) break; } + md_integrity_add_rdev(rdev, mddev); print_conf(conf); return err; } @@ -1203,7 +1204,9 @@ static int raid10_remove_disk(mddev_t *mddev, int number) /* lost the race, try later */ err = -EBUSY; p->rdev = rdev; + goto abort; } + md_integrity_register(mddev); } abort: @@ -2225,6 +2228,7 @@ static int run(mddev_t *mddev) if (conf->near_copies < mddev->raid_disks) blk_queue_merge_bvec(mddev->queue, raid10_mergeable_bvec); + md_integrity_register(mddev); return 0; out_free_conf: -- GitLab From 3a981b03f38dc3b8a69b77cbc679e66c1318a44a Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Mon, 3 Aug 2009 10:59:55 +1000 Subject: [PATCH 0694/1342] md: when a level change reduces the number of devices, remove the excess. When an array is changed from RAID6 to RAID5, fewer drives are needed. So any device that is made superfluous by the level conversion must be marked as not-active. For the RAID6->RAID5 conversion, this will be a drive which only has 'Q' blocks on it. Cc: stable@kernel.org Signed-off-by: NeilBrown --- drivers/md/md.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/md/md.c b/drivers/md/md.c index 180949e94a7..c194955aeca 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -2695,6 +2695,7 @@ level_store(mddev_t *mddev, const char *buf, size_t len) ssize_t rv = len; struct mdk_personality *pers; void *priv; + mdk_rdev_t *rdev; if (mddev->pers == NULL) { if (len == 0) @@ -2774,6 +2775,12 @@ level_store(mddev_t *mddev, const char *buf, size_t len) mddev_suspend(mddev); mddev->pers->stop(mddev); module_put(mddev->pers->owner); + /* Invalidate devices that are now superfluous */ + list_for_each_entry(rdev, &mddev->disks, same_set) + if (rdev->raid_disk >= mddev->raid_disks) { + rdev->raid_disk = -1; + clear_bit(In_sync, &rdev->flags); + } mddev->pers = pers; mddev->private = priv; strlcpy(mddev->clevel, pers->name, sizeof(mddev->clevel)); -- GitLab From 3673f305faf1bc66ead751344f8262ace851ff44 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Mon, 3 Aug 2009 10:59:56 +1000 Subject: [PATCH 0695/1342] md: avoid array overflow with bad v1.x metadata We trust the 'desc_nr' field in v1.x metadata enough to use it as an index in an array. This isn't really safe. So range-check the value first. Signed-off-by: NeilBrown --- drivers/md/md.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/drivers/md/md.c b/drivers/md/md.c index c194955aeca..249b2896d4e 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -1308,7 +1308,12 @@ static int super_1_validate(mddev_t *mddev, mdk_rdev_t *rdev) } if (mddev->level != LEVEL_MULTIPATH) { int role; - role = le16_to_cpu(sb->dev_roles[rdev->desc_nr]); + if (rdev->desc_nr < 0 || + rdev->desc_nr >= le32_to_cpu(sb->max_dev)) { + role = 0xffff; + rdev->desc_nr = -1; + } else + role = le16_to_cpu(sb->dev_roles[rdev->desc_nr]); switch(role) { case 0xffff: /* spare */ break; -- GitLab From 70471dafe3390243c598a3165dfb86b8b8b3f4fe Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Mon, 3 Aug 2009 10:59:57 +1000 Subject: [PATCH 0696/1342] md: Handle growth of v1.x metadata correctly. The v1.x metadata does not have a fixed size and can grow when devices are added. If it grows enough to require an extra sector of storage, we need to update the 'sb_size' to match. Without this, md can write out an incomplete superblock with a bad checksum, which will be rejected when trying to re-assemble the array. Cc: stable@kernel.org Signed-off-by: NeilBrown --- drivers/md/md.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/drivers/md/md.c b/drivers/md/md.c index 249b2896d4e..52c988b072d 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -1399,8 +1399,14 @@ static void super_1_sync(mddev_t *mddev, mdk_rdev_t *rdev) if (rdev2->desc_nr+1 > max_dev) max_dev = rdev2->desc_nr+1; - if (max_dev > le32_to_cpu(sb->max_dev)) + if (max_dev > le32_to_cpu(sb->max_dev)) { + int bmask; sb->max_dev = cpu_to_le32(max_dev); + rdev->sb_size = max_dev * 2 + 256; + bmask = queue_logical_block_size(rdev->bdev->bd_disk->queue)-1; + if (rdev->sb_size & bmask) + rdev->sb_size = (rdev->sb_size | bmask) + 1; + } for (i=0; idev_roles[i] = cpu_to_le16(0xfffe); -- GitLab From e516402c0d4fc02be4af9fa8c18954d4f9deb44e Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Mon, 3 Aug 2009 10:59:57 +1000 Subject: [PATCH 0697/1342] md/raid5: set reshape_position correctly when reshape starts. As the internal reshape_progress counter is the main driver for reshape, the fact that reshape_position sometimes starts with the wrong value has minimal effect. It is visible in sysfs and that is all. Signed-off-by: NeilBrown --- drivers/md/raid5.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c index 39374230a46..659151e5eda 100644 --- a/drivers/md/raid5.c +++ b/drivers/md/raid5.c @@ -5000,7 +5000,7 @@ static int raid5_start_reshape(mddev_t *mddev) spin_unlock_irqrestore(&conf->device_lock, flags); } mddev->raid_disks = conf->raid_disks; - mddev->reshape_position = 0; + mddev->reshape_position = conf->reshape_progress; set_bit(MD_CHANGE_DEVS, &mddev->flags); clear_bit(MD_RECOVERY_SYNC, &mddev->recovery); -- GitLab From 64bd660b51b2da92e99a5e97349f6558349f11c5 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Mon, 3 Aug 2009 10:59:58 +1000 Subject: [PATCH 0698/1342] md: allow raid5_quiesce to work properly when reshape is happening. The ->quiesce method is not supposed to stop resync/recovery/reshape, just normal IO. But in raid5 we don't have a way to know which stripes are being used for normal IO and which for resync etc, so we need to wait for all stripes to be idle to be sure that all writes have completed. However reshape keeps at least some stripe busy for an extended period of time, so a call to raid5_quiesce can block for several seconds needlessly. So arrange for reshape etc to pause briefly while raid5_quiesce is trying to quiesce the array so that the active_stripes count can drop to zero. Signed-off-by: NeilBrown --- drivers/md/raid5.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-) diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c index 659151e5eda..2dc35b4c20a 100644 --- a/drivers/md/raid5.c +++ b/drivers/md/raid5.c @@ -3999,6 +3999,9 @@ static inline sector_t sync_request(mddev_t *mddev, sector_t sector_nr, int *ski return 0; } + /* Allow raid5_quiesce to complete */ + wait_event(conf->wait_for_overlap, conf->quiesce != 2); + if (test_bit(MD_RECOVERY_RESHAPE, &mddev->recovery)) return reshape_request(mddev, sector_nr, skipped); @@ -5104,12 +5107,18 @@ static void raid5_quiesce(mddev_t *mddev, int state) case 1: /* stop all writes */ spin_lock_irq(&conf->device_lock); - conf->quiesce = 1; + /* '2' tells resync/reshape to pause so that all + * active stripes can drain + */ + conf->quiesce = 2; wait_event_lock_irq(conf->wait_for_stripe, atomic_read(&conf->active_stripes) == 0 && atomic_read(&conf->active_aligned_reads) == 0, conf->device_lock, /* nothing */); + conf->quiesce = 1; spin_unlock_irq(&conf->device_lock); + /* allow reshape to continue */ + wake_up(&conf->wait_for_overlap); break; case 0: /* re-enable writes */ -- GitLab From 449aad3e25358812c43afc60918c5ad3819488e7 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Mon, 3 Aug 2009 10:59:58 +1000 Subject: [PATCH 0699/1342] md: Use revalidate_disk to effect changes in size of device. As revalidate_disk calls check_disk_size_change, it will cause any capacity change of a gendisk to be propagated to the blockdev inode. So use that instead of mucking about with locks and i_size_write. Also add a call to revalidate_disk in do_md_run and a few other places where the gendisk capacity is changed. Signed-off-by: NeilBrown --- drivers/md/linear.c | 1 + drivers/md/md.c | 28 +++++----------------------- drivers/md/raid1.c | 1 + drivers/md/raid5.c | 12 ++---------- 4 files changed, 9 insertions(+), 33 deletions(-) diff --git a/drivers/md/linear.c b/drivers/md/linear.c index 54c8677f1e5..5fe39c2a3d2 100644 --- a/drivers/md/linear.c +++ b/drivers/md/linear.c @@ -257,6 +257,7 @@ static int linear_add(mddev_t *mddev, mdk_rdev_t *rdev) rcu_assign_pointer(mddev->private, newconf); md_set_array_sectors(mddev, linear_size(mddev, 0, 0)); set_capacity(mddev->gendisk, mddev->array_sectors); + revalidate_disk(mddev->gendisk); call_rcu(&oldconf->rcu, free_conf); return 0; } diff --git a/drivers/md/md.c b/drivers/md/md.c index 52c988b072d..5b98bea4ff9 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -3741,17 +3741,8 @@ array_size_store(mddev_t *mddev, const char *buf, size_t len) mddev->array_sectors = sectors; set_capacity(mddev->gendisk, mddev->array_sectors); - if (mddev->pers) { - struct block_device *bdev = bdget_disk(mddev->gendisk, 0); - - if (bdev) { - mutex_lock(&bdev->bd_inode->i_mutex); - i_size_write(bdev->bd_inode, - (loff_t)mddev->array_sectors << 9); - mutex_unlock(&bdev->bd_inode->i_mutex); - bdput(bdev); - } - } + if (mddev->pers) + revalidate_disk(mddev->gendisk); return len; } @@ -4241,6 +4232,7 @@ static int do_md_run(mddev_t * mddev) md_wakeup_thread(mddev->thread); md_wakeup_thread(mddev->sync_thread); /* possibly kick off a reshape */ + revalidate_disk(mddev->gendisk); mddev->changed = 1; md_new_event(mddev); sysfs_notify_dirent(mddev->sysfs_state); @@ -5139,18 +5131,8 @@ static int update_size(mddev_t *mddev, sector_t num_sectors) return -ENOSPC; } rv = mddev->pers->resize(mddev, num_sectors); - if (!rv) { - struct block_device *bdev; - - bdev = bdget_disk(mddev->gendisk, 0); - if (bdev) { - mutex_lock(&bdev->bd_inode->i_mutex); - i_size_write(bdev->bd_inode, - (loff_t)mddev->array_sectors << 9); - mutex_unlock(&bdev->bd_inode->i_mutex); - bdput(bdev); - } - } + if (!rv) + revalidate_disk(mddev->gendisk); return rv; } diff --git a/drivers/md/raid1.c b/drivers/md/raid1.c index 67e794d0097..8726fd7ebce 100644 --- a/drivers/md/raid1.c +++ b/drivers/md/raid1.c @@ -2134,6 +2134,7 @@ static int raid1_resize(mddev_t *mddev, sector_t sectors) return -EINVAL; set_capacity(mddev->gendisk, mddev->array_sectors); mddev->changed = 1; + revalidate_disk(mddev->gendisk); if (sectors > mddev->dev_sectors && mddev->recovery_cp == MaxSector) { mddev->recovery_cp = mddev->dev_sectors; diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c index 2dc35b4c20a..2b521ee67df 100644 --- a/drivers/md/raid5.c +++ b/drivers/md/raid5.c @@ -4858,6 +4858,7 @@ static int raid5_resize(mddev_t *mddev, sector_t sectors) return -EINVAL; set_capacity(mddev->gendisk, mddev->array_sectors); mddev->changed = 1; + revalidate_disk(mddev->gendisk); if (sectors > mddev->dev_sectors && mddev->recovery_cp == MaxSector) { mddev->recovery_cp = mddev->dev_sectors; set_bit(MD_RECOVERY_NEEDED, &mddev->recovery); @@ -5058,7 +5059,6 @@ static void end_reshape(raid5_conf_t *conf) */ static void raid5_finish_reshape(mddev_t *mddev) { - struct block_device *bdev; raid5_conf_t *conf = mddev->private; if (!test_bit(MD_RECOVERY_INTR, &mddev->recovery)) { @@ -5067,15 +5067,7 @@ static void raid5_finish_reshape(mddev_t *mddev) md_set_array_sectors(mddev, raid5_size(mddev, 0, 0)); set_capacity(mddev->gendisk, mddev->array_sectors); mddev->changed = 1; - - bdev = bdget_disk(mddev->gendisk, 0); - if (bdev) { - mutex_lock(&bdev->bd_inode->i_mutex); - i_size_write(bdev->bd_inode, - (loff_t)mddev->array_sectors << 9); - mutex_unlock(&bdev->bd_inode->i_mutex); - bdput(bdev); - } + revalidate_disk(mddev->gendisk); } else { int d; mddev->degraded = conf->raid_disks; -- GitLab From a923c28fc538a4161b15e9b5d7d48248d73d3e6f Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Sun, 2 Aug 2009 19:17:15 -0700 Subject: [PATCH 0700/1342] sparc: Use page_fault_out_of_memory() for VM_FAULT_OOM. As noted by Nick Piggin. Signed-off-by: David S. Miller --- arch/sparc/mm/fault_32.c | 7 ++++--- arch/sparc/mm/fault_64.c | 7 ++++--- 2 files changed, 8 insertions(+), 6 deletions(-) diff --git a/arch/sparc/mm/fault_32.c b/arch/sparc/mm/fault_32.c index a5e30c642ee..b99f81c4906 100644 --- a/arch/sparc/mm/fault_32.c +++ b/arch/sparc/mm/fault_32.c @@ -319,9 +319,10 @@ no_context: */ out_of_memory: up_read(&mm->mmap_sem); - printk("VM: killing process %s\n", tsk->comm); - if (from_user) - do_group_exit(SIGKILL); + if (from_user) { + pagefault_out_of_memory(); + return; + } goto no_context; do_sigbus: diff --git a/arch/sparc/mm/fault_64.c b/arch/sparc/mm/fault_64.c index e5620b27c8b..43b0da96a4f 100644 --- a/arch/sparc/mm/fault_64.c +++ b/arch/sparc/mm/fault_64.c @@ -447,9 +447,10 @@ handle_kernel_fault: out_of_memory: insn = get_fault_insn(regs, insn); up_read(&mm->mmap_sem); - printk("VM: killing process %s\n", current->comm); - if (!(regs->tstate & TSTATE_PRIV)) - do_group_exit(SIGKILL); + if (!(regs->tstate & TSTATE_PRIV)) { + pagefault_out_of_memory(); + return; + } goto handle_kernel_fault; intr_or_no_mm: -- GitLab From eb4ad826419ab5b1260bc1625249114767d36bea Mon Sep 17 00:00:00 2001 From: Yevgeny Petrilin Date: Sun, 2 Aug 2009 20:22:18 -0700 Subject: [PATCH 0701/1342] mlx4_en: Fix double pci unmapping. In cases of fragmented skb, with the data pointers being wrapped around the TX buffer, the completion handling code would not forward the data pointer and the firs fragment was unmapped several times, while others were not unmapped at all. Signed-off-by: Yevgeny Petrilin Signed-off-by: David S. Miller --- drivers/net/mlx4/en_tx.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/net/mlx4/en_tx.c b/drivers/net/mlx4/en_tx.c index 08c43f2ae72..5a88b3f5769 100644 --- a/drivers/net/mlx4/en_tx.c +++ b/drivers/net/mlx4/en_tx.c @@ -249,6 +249,7 @@ static u32 mlx4_en_free_tx_desc(struct mlx4_en_priv *priv, pci_unmap_page(mdev->pdev, (dma_addr_t) be64_to_cpu(data->addr), frag->size, PCI_DMA_TODEVICE); + ++data; } } /* Stamp the freed descriptor */ -- GitLab From ce577e8cf5ddb4216553c9d563a9835d6de70ffa Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Mon, 3 Aug 2009 08:23:52 +0200 Subject: [PATCH 0702/1342] ALSA: hda - Fix quirk for Toshiba Satellite A135-S4527 Use model=lenovo instead of model=dallas for Toshiba Satellite A135-S4527 with ALC861-VD codec. Reference: Novell bnc#526325 https://bugzilla.novell.com/show_bug.cgi?id=526325 Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_realtek.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index b95df5d5dcc..f6b4cbf1ead 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -15157,7 +15157,7 @@ static struct snd_pci_quirk alc861vd_cfg_tbl[] = { SND_PCI_QUIRK(0x10de, 0x03f0, "Realtek ALC660 demo", ALC660VD_3ST), SND_PCI_QUIRK(0x1179, 0xff00, "Toshiba A135", ALC861VD_LENOVO), /*SND_PCI_QUIRK(0x1179, 0xff00, "DALLAS", ALC861VD_DALLAS),*/ /*lenovo*/ - SND_PCI_QUIRK(0x1179, 0xff01, "DALLAS", ALC861VD_DALLAS), + SND_PCI_QUIRK(0x1179, 0xff01, "Toshiba A135", ALC861VD_LENOVO), SND_PCI_QUIRK(0x1179, 0xff03, "Toshiba P205", ALC861VD_LENOVO), SND_PCI_QUIRK(0x1179, 0xff31, "Toshiba L30-149", ALC861VD_DALLAS), SND_PCI_QUIRK(0x1565, 0x820d, "Biostar NF61S SE", ALC861VD_6ST_DIG), -- GitLab From deadff1665491afce124a8ff83f00f784161f660 Mon Sep 17 00:00:00 2001 From: Wu Fengguang Date: Sat, 1 Aug 2009 18:45:16 +0800 Subject: [PATCH 0703/1342] ALSA: hda: track CIRB/CORB command/response states for each codec Recently we hit a bug in our dev board, whose HDMI codec#3 may emit redundant/spurious responses, which were then taken as responses to command for another onboard Realtek codec#2, and mess up both codecs. Extend the azx_rb.cmds and azx_rb.res to array and track each codec's commands/responses separately. This helps keep good codec safe from broken ones. Signed-off-by: Wu Fengguang Signed-off-by: Takashi Iwai --- sound/pci/hda/hda_codec.c | 2 +- sound/pci/hda/hda_codec.h | 2 +- sound/pci/hda/hda_intel.c | 76 +++++++++++++++++++++++++++------------ 3 files changed, 56 insertions(+), 24 deletions(-) diff --git a/sound/pci/hda/hda_codec.c b/sound/pci/hda/hda_codec.c index 88480c0c58a..c7df01b72ca 100644 --- a/sound/pci/hda/hda_codec.c +++ b/sound/pci/hda/hda_codec.c @@ -174,7 +174,7 @@ static int codec_exec_verb(struct hda_codec *codec, unsigned int cmd, mutex_lock(&bus->cmd_mutex); err = bus->ops.command(bus, cmd); if (!err && res) - *res = bus->ops.get_response(bus); + *res = bus->ops.get_response(bus, codec->addr); mutex_unlock(&bus->cmd_mutex); snd_hda_power_down(codec); if (res && *res == -1 && bus->rirb_error) { diff --git a/sound/pci/hda/hda_codec.h b/sound/pci/hda/hda_codec.h index cad79efaabc..1b75f28ed09 100644 --- a/sound/pci/hda/hda_codec.h +++ b/sound/pci/hda/hda_codec.h @@ -568,7 +568,7 @@ struct hda_bus_ops { /* send a single command */ int (*command)(struct hda_bus *bus, unsigned int cmd); /* get a response from the last command */ - unsigned int (*get_response)(struct hda_bus *bus); + unsigned int (*get_response)(struct hda_bus *bus, unsigned int addr); /* free the private data */ void (*private_free)(struct hda_bus *); /* attach a PCM stream */ diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c index 77c1b840ca8..19e67a1b602 100644 --- a/sound/pci/hda/hda_intel.c +++ b/sound/pci/hda/hda_intel.c @@ -253,7 +253,7 @@ enum { SDI0, SDI1, SDI2, SDI3, SDO0, SDO1, SDO2, SDO3 }; /* STATESTS int mask: S3,SD2,SD1,SD0 */ #define AZX_MAX_CODECS 4 -#define STATESTS_INT_MASK 0x0f +#define STATESTS_INT_MASK ((1 << AZX_MAX_CODECS) - 1) /* SD_CTL bits */ #define SD_CTL_STREAM_RESET 0x01 /* stream reset bit */ @@ -361,8 +361,8 @@ struct azx_rb { dma_addr_t addr; /* physical address of CORB/RIRB buffer */ /* for RIRB */ unsigned short rp, wp; /* read/write pointers */ - int cmds; /* number of pending requests */ - u32 res; /* last read value */ + int cmds[AZX_MAX_CODECS]; /* number of pending requests */ + u32 res[AZX_MAX_CODECS]; /* last read value */ }; struct azx { @@ -531,7 +531,8 @@ static void azx_init_cmd_io(struct azx *chip) /* RIRB set up */ chip->rirb.addr = chip->rb.addr + 2048; chip->rirb.buf = (u32 *)(chip->rb.area + 2048); - chip->rirb.wp = chip->rirb.rp = chip->rirb.cmds = 0; + chip->rirb.wp = chip->rirb.rp = 0; + memset(chip->rirb.cmds, 0, sizeof(chip->rirb.cmds)); azx_writel(chip, RIRBLBASE, (u32)chip->rirb.addr); azx_writel(chip, RIRBUBASE, upper_32_bits(chip->rirb.addr)); @@ -552,10 +553,35 @@ static void azx_free_cmd_io(struct azx *chip) azx_writeb(chip, CORBCTL, 0); } +static unsigned int azx_command_addr(u32 cmd) +{ + unsigned int addr = cmd >> 28; + + if (addr >= AZX_MAX_CODECS) { + snd_BUG(); + addr = 0; + } + + return addr; +} + +static unsigned int azx_response_addr(u32 res) +{ + unsigned int addr = res & 0xf; + + if (addr >= AZX_MAX_CODECS) { + snd_BUG(); + addr = 0; + } + + return addr; +} + /* send a command */ static int azx_corb_send_cmd(struct hda_bus *bus, u32 val) { struct azx *chip = bus->private_data; + unsigned int addr = azx_command_addr(val); unsigned int wp; /* add command to corb */ @@ -564,7 +590,7 @@ static int azx_corb_send_cmd(struct hda_bus *bus, u32 val) wp %= ICH6_MAX_CORB_ENTRIES; spin_lock_irq(&chip->reg_lock); - chip->rirb.cmds++; + chip->rirb.cmds[addr]++; chip->corb.buf[wp] = cpu_to_le32(val); azx_writel(chip, CORBWP, wp); spin_unlock_irq(&chip->reg_lock); @@ -578,13 +604,14 @@ static int azx_corb_send_cmd(struct hda_bus *bus, u32 val) static void azx_update_rirb(struct azx *chip) { unsigned int rp, wp; + unsigned int addr; u32 res, res_ex; wp = azx_readb(chip, RIRBWP); if (wp == chip->rirb.wp) return; chip->rirb.wp = wp; - + while (chip->rirb.rp != wp) { chip->rirb.rp++; chip->rirb.rp %= ICH6_MAX_RIRB_ENTRIES; @@ -592,18 +619,20 @@ static void azx_update_rirb(struct azx *chip) rp = chip->rirb.rp << 1; /* an RIRB entry is 8-bytes */ res_ex = le32_to_cpu(chip->rirb.buf[rp + 1]); res = le32_to_cpu(chip->rirb.buf[rp]); + addr = azx_response_addr(res_ex); if (res_ex & ICH6_RIRB_EX_UNSOL_EV) snd_hda_queue_unsol_event(chip->bus, res, res_ex); - else if (chip->rirb.cmds) { - chip->rirb.res = res; + else if (chip->rirb.cmds[addr]) { + chip->rirb.res[addr] = res; smp_wmb(); - chip->rirb.cmds--; + chip->rirb.cmds[addr]--; } } } /* receive a response */ -static unsigned int azx_rirb_get_response(struct hda_bus *bus) +static unsigned int azx_rirb_get_response(struct hda_bus *bus, + unsigned int addr) { struct azx *chip = bus->private_data; unsigned long timeout; @@ -616,10 +645,10 @@ static unsigned int azx_rirb_get_response(struct hda_bus *bus) azx_update_rirb(chip); spin_unlock_irq(&chip->reg_lock); } - if (!chip->rirb.cmds) { + if (!chip->rirb.cmds[addr]) { smp_rmb(); bus->rirb_error = 0; - return chip->rirb.res; /* the last value */ + return chip->rirb.res[addr]; /* the last value */ } if (time_after(jiffies, timeout)) break; @@ -692,7 +721,7 @@ static unsigned int azx_rirb_get_response(struct hda_bus *bus) */ /* receive a response */ -static int azx_single_wait_for_response(struct azx *chip) +static int azx_single_wait_for_response(struct azx *chip, unsigned int addr) { int timeout = 50; @@ -700,7 +729,7 @@ static int azx_single_wait_for_response(struct azx *chip) /* check IRV busy bit */ if (azx_readw(chip, IRS) & ICH6_IRS_VALID) { /* reuse rirb.res as the response return value */ - chip->rirb.res = azx_readl(chip, IR); + chip->rirb.res[addr] = azx_readl(chip, IR); return 0; } udelay(1); @@ -708,7 +737,7 @@ static int azx_single_wait_for_response(struct azx *chip) if (printk_ratelimit()) snd_printd(SFX "get_response timeout: IRS=0x%x\n", azx_readw(chip, IRS)); - chip->rirb.res = -1; + chip->rirb.res[addr] = -1; return -EIO; } @@ -716,6 +745,7 @@ static int azx_single_wait_for_response(struct azx *chip) static int azx_single_send_cmd(struct hda_bus *bus, u32 val) { struct azx *chip = bus->private_data; + unsigned int addr = azx_command_addr(val); int timeout = 50; bus->rirb_error = 0; @@ -728,7 +758,7 @@ static int azx_single_send_cmd(struct hda_bus *bus, u32 val) azx_writel(chip, IC, val); azx_writew(chip, IRS, azx_readw(chip, IRS) | ICH6_IRS_BUSY); - return azx_single_wait_for_response(chip); + return azx_single_wait_for_response(chip, addr); } udelay(1); } @@ -739,10 +769,11 @@ static int azx_single_send_cmd(struct hda_bus *bus, u32 val) } /* receive a response */ -static unsigned int azx_single_get_response(struct hda_bus *bus) +static unsigned int azx_single_get_response(struct hda_bus *bus, + unsigned int addr) { struct azx *chip = bus->private_data; - return chip->rirb.res; + return chip->rirb.res[addr]; } /* @@ -765,13 +796,14 @@ static int azx_send_cmd(struct hda_bus *bus, unsigned int val) } /* get a response */ -static unsigned int azx_get_response(struct hda_bus *bus) +static unsigned int azx_get_response(struct hda_bus *bus, + unsigned int addr) { struct azx *chip = bus->private_data; if (chip->single_cmd) - return azx_single_get_response(bus); + return azx_single_get_response(bus, addr); else - return azx_rirb_get_response(bus); + return azx_rirb_get_response(bus, addr); } #ifdef CONFIG_SND_HDA_POWER_SAVE @@ -1245,7 +1277,7 @@ static int probe_codec(struct azx *chip, int addr) chip->probing = 1; azx_send_cmd(chip->bus, cmd); - res = azx_get_response(chip->bus); + res = azx_get_response(chip->bus, addr); chip->probing = 0; if (res == -1) return -EIO; -- GitLab From a678cdee25a387c8fc3b2754974695412baf1d85 Mon Sep 17 00:00:00 2001 From: Wu Fengguang Date: Sat, 1 Aug 2009 18:46:46 +0800 Subject: [PATCH 0704/1342] ALSA: hda: take cmd_mutex in probe_codec() Now that each codec will have its own module, it is possible for the user to load one codec while another one is running. So cmd_mutex would be a safe addition to probe_codec(). Signed-off-by: Wu Fengguang Signed-off-by: Takashi Iwai --- sound/pci/hda/hda_intel.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c index 19e67a1b602..ddabc827ac4 100644 --- a/sound/pci/hda/hda_intel.c +++ b/sound/pci/hda/hda_intel.c @@ -1275,10 +1275,12 @@ static int probe_codec(struct azx *chip, int addr) (AC_VERB_PARAMETERS << 8) | AC_PAR_VENDOR_ID; unsigned int res; + mutex_lock(&chip->bus->cmd_mutex); chip->probing = 1; azx_send_cmd(chip->bus, cmd); res = azx_get_response(chip->bus, addr); chip->probing = 0; + mutex_unlock(&chip->bus->cmd_mutex); if (res == -1) return -EIO; snd_printdd(SFX "codec #%d probed OK\n", addr); -- GitLab From cdb1fbf23181c133fb24f12ad14ccea7dc399599 Mon Sep 17 00:00:00 2001 From: Wu Fengguang Date: Sat, 1 Aug 2009 18:47:41 +0800 Subject: [PATCH 0705/1342] ALSA: hda: take reg_lock in azx_init_cmd_io/azx_free_cmd_io Just for safety. azx_init_cmd_io() and azx_free_cmd_io() may be called when switching to single command mode. Signed-off-by: Wu Fengguang Signed-off-by: Takashi Iwai --- sound/pci/hda/hda_intel.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c index ddabc827ac4..b6e6314d006 100644 --- a/sound/pci/hda/hda_intel.c +++ b/sound/pci/hda/hda_intel.c @@ -513,6 +513,7 @@ static int azx_alloc_cmd_io(struct azx *chip) static void azx_init_cmd_io(struct azx *chip) { + spin_lock_irq(&chip->reg_lock); /* CORB set up */ chip->corb.addr = chip->rb.addr; chip->corb.buf = (u32 *)chip->rb.area; @@ -544,13 +545,16 @@ static void azx_init_cmd_io(struct azx *chip) azx_writew(chip, RINTCNT, 1); /* enable rirb dma and response irq */ azx_writeb(chip, RIRBCTL, ICH6_RBCTL_DMA_EN | ICH6_RBCTL_IRQ_EN); + spin_unlock_irq(&chip->reg_lock); } static void azx_free_cmd_io(struct azx *chip) { + spin_lock_irq(&chip->reg_lock); /* disable ringbuffer DMAs */ azx_writeb(chip, RIRBCTL, 0); azx_writeb(chip, CORBCTL, 0); + spin_unlock_irq(&chip->reg_lock); } static unsigned int azx_command_addr(u32 cmd) -- GitLab From c32649feb4573b31f0a2bfdf35cbe1351256c764 Mon Sep 17 00:00:00 2001 From: Wu Fengguang Date: Sat, 1 Aug 2009 18:48:12 +0800 Subject: [PATCH 0706/1342] ALSA: hda: read CORBWP inside reg_lock This converts the last CORBWP access outside of reg_lock. Signed-off-by: Wu Fengguang Signed-off-by: Takashi Iwai --- sound/pci/hda/hda_intel.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c index b6e6314d006..df6d9820efa 100644 --- a/sound/pci/hda/hda_intel.c +++ b/sound/pci/hda/hda_intel.c @@ -588,15 +588,17 @@ static int azx_corb_send_cmd(struct hda_bus *bus, u32 val) unsigned int addr = azx_command_addr(val); unsigned int wp; + spin_lock_irq(&chip->reg_lock); + /* add command to corb */ wp = azx_readb(chip, CORBWP); wp++; wp %= ICH6_MAX_CORB_ENTRIES; - spin_lock_irq(&chip->reg_lock); chip->rirb.cmds[addr]++; chip->corb.buf[wp] = cpu_to_le32(val); azx_writel(chip, CORBWP, wp); + spin_unlock_irq(&chip->reg_lock); return 0; -- GitLab From feb273404f15d86098cb0e81e46330d5c1e22b1b Mon Sep 17 00:00:00 2001 From: Wu Fengguang Date: Sat, 1 Aug 2009 19:17:14 +0800 Subject: [PATCH 0707/1342] ALSA: hda: remember last command for each codec Signed-off-by: Wu Fengguang Signed-off-by: Takashi Iwai --- sound/pci/hda/hda_intel.c | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-) diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c index df6d9820efa..7c43f92de2f 100644 --- a/sound/pci/hda/hda_intel.c +++ b/sound/pci/hda/hda_intel.c @@ -418,7 +418,7 @@ struct azx { unsigned int probing :1; /* codec probing phase */ /* for debugging */ - unsigned int last_cmd; /* last issued command (to sync) */ + unsigned int last_cmd[AZX_MAX_CODECS]; /* for pending irqs */ struct work_struct irq_pending_work; @@ -668,7 +668,8 @@ static unsigned int azx_rirb_get_response(struct hda_bus *bus, if (chip->msi) { snd_printk(KERN_WARNING SFX "No response from codec, " - "disabling MSI: last cmd=0x%08x\n", chip->last_cmd); + "disabling MSI: last cmd=0x%08x\n", + chip->last_cmd[addr]); free_irq(chip->irq, chip); chip->irq = -1; pci_disable_msi(chip->pci); @@ -683,7 +684,7 @@ static unsigned int azx_rirb_get_response(struct hda_bus *bus, if (!chip->polling_mode) { snd_printk(KERN_WARNING SFX "azx_get_response timeout, " "switching to polling mode: last cmd=0x%08x\n", - chip->last_cmd); + chip->last_cmd[addr]); chip->polling_mode = 1; goto again; } @@ -707,7 +708,7 @@ static unsigned int azx_rirb_get_response(struct hda_bus *bus, snd_printk(KERN_ERR "hda_intel: azx_get_response timeout, " "switching to single_cmd mode: last cmd=0x%08x\n", - chip->last_cmd); + chip->last_cmd[addr]); chip->single_cmd = 1; bus->response_reset = 0; /* re-initialize CORB/RIRB */ @@ -794,7 +795,7 @@ static int azx_send_cmd(struct hda_bus *bus, unsigned int val) { struct azx *chip = bus->private_data; - chip->last_cmd = val; + chip->last_cmd[azx_command_addr(val)] = val; if (chip->single_cmd) return azx_single_send_cmd(bus, val); else -- GitLab From e310bb0646e57a4f9182865115c5780931456c65 Mon Sep 17 00:00:00 2001 From: Wu Fengguang Date: Sat, 1 Aug 2009 19:18:45 +0800 Subject: [PATCH 0708/1342] ALSA: hda: warn on spurious response To help disclose hardware bugs. Signed-off-by: Wu Fengguang Signed-off-by: Takashi Iwai --- sound/pci/hda/hda_intel.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c index 7c43f92de2f..175f07a381b 100644 --- a/sound/pci/hda/hda_intel.c +++ b/sound/pci/hda/hda_intel.c @@ -632,7 +632,11 @@ static void azx_update_rirb(struct azx *chip) chip->rirb.res[addr] = res; smp_wmb(); chip->rirb.cmds[addr]--; - } + } else + snd_printk(KERN_ERR SFX "spurious response %#x:%#x, " + "last cmd=%#08x\n", + res, res_ex, + chip->last_cmd[addr]); } } -- GitLab From 84d3dc200fc8b878acf7c1840b238e6a0450e4d0 Mon Sep 17 00:00:00 2001 From: Chengu Wang Date: Thu, 30 Jul 2009 19:43:55 +0800 Subject: [PATCH 0709/1342] ALSA: hda: Correct EAPD for Dell Inspiron 1525 The commit 24918b61b55c21e09a3e07cd82e1b3a8154782dc statically changes the model from dell-bios to dell-3stack to solve the sound decreasing regression (http://lkml.org/lkml/2008/9/12/203), however it leads to another problem that the 2nd headphone jack doesn't work (https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3987). So I think the commit 249**2dc is just a workaround. I would like to give a true solution here. The datasheet for STAC9228 says, GPIO2 is the same pin as VOL DOWN, and the EAPD pin is GPIO0. This is why the sound decreases if we set EAPD as GPIO2. This patch changes EAPD to GPIO0 to solve the problem. Signed-off-by: Chengu Wang Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_sigmatel.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) diff --git a/sound/pci/hda/patch_sigmatel.c b/sound/pci/hda/patch_sigmatel.c index 5383d8cff88..456ef6ac12e 100644 --- a/sound/pci/hda/patch_sigmatel.c +++ b/sound/pci/hda/patch_sigmatel.c @@ -2266,7 +2266,7 @@ static struct snd_pci_quirk stac927x_cfg_tbl[] = { SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x01f3, "Dell Inspiron 1420", STAC_DELL_BIOS), SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x0227, "Dell Vostro 1400 ", STAC_DELL_BIOS), SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x022e, "Dell ", STAC_DELL_BIOS), - SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x022f, "Dell Inspiron 1525", STAC_DELL_3ST), + SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x022f, "Dell Inspiron 1525", STAC_DELL_BIOS), SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x0242, "Dell ", STAC_DELL_BIOS), SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x0243, "Dell ", STAC_DELL_BIOS), SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x02ff, "Dell ", STAC_DELL_BIOS), @@ -5645,6 +5645,13 @@ static int patch_stac927x(struct hda_codec *codec) /* GPIO2 High = Enable EAPD */ spec->eapd_mask = spec->gpio_mask = spec->gpio_dir = 0x04; spec->gpio_data = 0x04; + switch (codec->subsystem_id) { + case 0x1028022f: + /* correct EAPD to be GPIO0 */ + spec->eapd_mask = spec->gpio_mask = 0x01; + spec->gpio_dir = spec->gpio_data = 0x01; + break; + }; spec->dmic_nids = stac927x_dmic_nids; spec->num_dmics = STAC927X_NUM_DMICS; -- GitLab From 4b35d2ca2307d40ccb6b3b6f9cc25ac9178b2a6c Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Sun, 2 Aug 2009 13:30:45 +0200 Subject: [PATCH 0710/1342] ALSA: hda - Read buffer overflow Check whether index is within bounds before testing the element. Signed-off-by: Roel Kluin Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_realtek.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index f6b4cbf1ead..51c44fdbc0f 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -559,7 +559,7 @@ static int alc_pin_mode_get(struct snd_kcontrol *kcontrol, /* Find enumerated value for current pinctl setting */ i = alc_pin_mode_min(dir); - while (alc_pin_mode_values[i] != pinctl && i <= alc_pin_mode_max(dir)) + while (i <= alc_pin_mode_max(dir) && alc_pin_mode_values[i] != pinctl) i++; *valp = i <= alc_pin_mode_max(dir) ? i: alc_pin_mode_min(dir); return 0; -- GitLab From 7699ad35ed06044c4fc1be162553880f98658616 Mon Sep 17 00:00:00 2001 From: Nicolas Pitre Date: Mon, 15 Jun 2009 01:10:18 -0400 Subject: [PATCH 0711/1342] mtd: let include/linux/mtd/partitions.h stand on its own When declaring static MTD partitions in board specific code, only including should suffice without gcc nagging us with: In file included from arch/arm/mach-kirkwood/sheevaplug-setup.c:14: include/linux/mtd/partitions.h:50: warning: 'struct mtd_info' declared inside parameter list include/linux/mtd/partitions.h:50: warning: its scope is only this definition or declaration, which is probably not what you want include/linux/mtd/partitions.h:51: warning: 'struct mtd_info' declared inside parameter list include/linux/mtd/partitions.h:61: warning: 'struct mtd_info' declared inside parameter list include/linux/mtd/partitions.h:67: warning: 'struct mtd_info' declared inside parameter list Signed-off-by: Nicolas Pitre Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse --- include/linux/mtd/partitions.h | 2 ++ 1 file changed, 2 insertions(+) diff --git a/include/linux/mtd/partitions.h b/include/linux/mtd/partitions.h index af6dcb992bc..b70313d33ff 100644 --- a/include/linux/mtd/partitions.h +++ b/include/linux/mtd/partitions.h @@ -47,6 +47,8 @@ struct mtd_partition { #define MTDPART_SIZ_FULL (0) +struct mtd_info; + int add_mtd_partitions(struct mtd_info *, const struct mtd_partition *, int); int del_mtd_partitions(struct mtd_info *); -- GitLab From 6afc4fdb3e94ba60cd566cb878b60c6c01979277 Mon Sep 17 00:00:00 2001 From: Saeed Bishara Date: Tue, 28 Jul 2009 04:56:43 -0700 Subject: [PATCH 0712/1342] mtd: fix the conversion from dev to mtd_info The patch fixes a bug when converting dev to mtd_info by using the drvdata of the dev, the previous code used container_of(dev, struct mtd_info, dev), but won't work for the mtdXro devices as they created without being contained inside mtd_info structure. Signed-off-by: Saeed Bishara Signed-off-by: David Woodhouse --- drivers/mtd/mtdcore.c | 7 ++++--- include/linux/mtd/mtd.h | 2 +- 2 files changed, 5 insertions(+), 4 deletions(-) diff --git a/drivers/mtd/mtdcore.c b/drivers/mtd/mtdcore.c index fac54a3fa3f..00ebf7af746 100644 --- a/drivers/mtd/mtdcore.c +++ b/drivers/mtd/mtdcore.c @@ -65,8 +65,8 @@ static void mtd_release(struct device *dev) static int mtd_cls_suspend(struct device *dev, pm_message_t state) { struct mtd_info *mtd = dev_to_mtd(dev); - - if (mtd->suspend) + + if (mtd && mtd->suspend) return mtd->suspend(mtd); else return 0; @@ -76,7 +76,7 @@ static int mtd_cls_resume(struct device *dev) { struct mtd_info *mtd = dev_to_mtd(dev); - if (mtd->resume) + if (mtd && mtd->resume) mtd->resume(mtd); return 0; } @@ -298,6 +298,7 @@ int add_mtd_device(struct mtd_info *mtd) mtd->dev.class = &mtd_class; mtd->dev.devt = MTD_DEVT(i); dev_set_name(&mtd->dev, "mtd%d", i); + dev_set_drvdata(&mtd->dev, mtd); if (device_register(&mtd->dev) != 0) { mtd_table[i] = NULL; break; diff --git a/include/linux/mtd/mtd.h b/include/linux/mtd/mtd.h index 5675b63a063..0f32a9b6ff5 100644 --- a/include/linux/mtd/mtd.h +++ b/include/linux/mtd/mtd.h @@ -251,7 +251,7 @@ struct mtd_info { static inline struct mtd_info *dev_to_mtd(struct device *dev) { - return dev ? container_of(dev, struct mtd_info, dev) : NULL; + return dev ? dev_get_drvdata(dev) : NULL; } static inline uint32_t mtd_div_by_eb(uint64_t sz, struct mtd_info *mtd) -- GitLab From 8022c13c27b822cf22f13df10b42aae89cd56bf0 Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Fri, 10 Jul 2009 17:02:17 +0300 Subject: [PATCH 0713/1342] mtd: blkdevs: do not forget to get MTD devices Nowadays MTD devices have to be "get" before they can be used. This has to be done with 'get_mtd_device()'. The 'blktrans_open()' function did not do this and instead used 'try_module_get()'. Fix this. Since 'get_mtd_device()' already gets the module, extra 'try_module_get()' is not needed. This fixes oops when one tries to use mtdblock on top of gluebi. Reported-by: Holger Brunck Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse --- drivers/mtd/mtd_blkdevs.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/mtd/mtd_blkdevs.c b/drivers/mtd/mtd_blkdevs.c index c3f62654b6d..7baba40c1ed 100644 --- a/drivers/mtd/mtd_blkdevs.c +++ b/drivers/mtd/mtd_blkdevs.c @@ -144,7 +144,7 @@ static int blktrans_open(struct block_device *bdev, fmode_t mode) struct mtd_blktrans_ops *tr = dev->tr; int ret = -ENODEV; - if (!try_module_get(dev->mtd->owner)) + if (!get_mtd_device(NULL, dev->mtd->index)) goto out; if (!try_module_get(tr->owner)) @@ -158,7 +158,7 @@ static int blktrans_open(struct block_device *bdev, fmode_t mode) ret = 0; if (tr->open && (ret = tr->open(dev))) { dev->mtd->usecount--; - module_put(dev->mtd->owner); + put_mtd_device(dev->mtd); out_tr: module_put(tr->owner); } @@ -177,7 +177,7 @@ static int blktrans_release(struct gendisk *disk, fmode_t mode) if (!ret) { dev->mtd->usecount--; - module_put(dev->mtd->owner); + put_mtd_device(dev->mtd); module_put(tr->owner); } -- GitLab From 00acf4a80779611a7ea77ff5b5ffab886ed5cc42 Mon Sep 17 00:00:00 2001 From: Mika Korhonen Date: Thu, 11 Jun 2009 14:05:07 +0300 Subject: [PATCH 0714/1342] mtd: OneNAND: fix incorrect bufferram offset Fixes the case where CONFIG_MTD_ONENAND_2X_PROGRAM is set and the real page size differs from mtd_info.writesize. Signed-off-by: Mika Korhonen Acked-by: Kyungmin Park Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse --- drivers/mtd/onenand/omap2.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c index 38d656b9b2e..6fac1f496d4 100644 --- a/drivers/mtd/onenand/omap2.c +++ b/drivers/mtd/onenand/omap2.c @@ -266,7 +266,7 @@ static inline int omap2_onenand_bufferram_offset(struct mtd_info *mtd, int area) if (ONENAND_CURRENT_BUFFERRAM(this)) { if (area == ONENAND_DATARAM) - return mtd->writesize; + return this->writesize; if (area == ONENAND_SPARERAM) return mtd->oobsize; } -- GitLab From 3cae1cc149c40c14424162496eb5a7c8db1cd4fb Mon Sep 17 00:00:00 2001 From: Mika Korhonen Date: Thu, 25 Jun 2009 15:32:19 +0300 Subject: [PATCH 0715/1342] mtd: OneNAND: OMAP2/3: free GPMC CS on module removal GPMC CS was not freed in omap2_onenand_remove() preventing the module from reloading after removal. Signed-off-by: Mika Korhonen Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse --- drivers/mtd/onenand/omap2.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c index 6fac1f496d4..0108ed42e87 100644 --- a/drivers/mtd/onenand/omap2.c +++ b/drivers/mtd/onenand/omap2.c @@ -770,6 +770,7 @@ static int __devexit omap2_onenand_remove(struct platform_device *pdev) } iounmap(c->onenand.base); release_mem_region(c->phys_base, ONENAND_IO_SIZE); + gpmc_cs_free(c->gpmc_cs); kfree(c); return 0; -- GitLab From 2bf961b7ccd69e108ac435c67e2b0522b403c578 Mon Sep 17 00:00:00 2001 From: Subrata Modak Date: Wed, 1 Jul 2009 19:22:47 +0530 Subject: [PATCH 0716/1342] mtd: remove 'SBC8240 Wind River' Device Driver Code This driver is causing build errors and is no longer needed -- it is obsoleted by physmap_of. Signed-off-by: Subrata Modak Tested-on-PPC64-by: Subrata Modak Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse --- drivers/mtd/maps/Kconfig | 7 -- drivers/mtd/maps/Makefile | 1 - drivers/mtd/maps/sbc8240.c | 250 ------------------------------------- 3 files changed, 258 deletions(-) diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig index 0b98654d8ee..7a58bd5522f 100644 --- a/drivers/mtd/maps/Kconfig +++ b/drivers/mtd/maps/Kconfig @@ -284,13 +284,6 @@ config MTD_L440GX BE VERY CAREFUL. -config MTD_SBC8240 - tristate "Flash device on SBC8240" - depends on MTD_JEDECPROBE && 8260 - help - Flash access on the SBC8240 board from Wind River. See - - config MTD_TQM8XXL tristate "CFI Flash device mapped on TQM8XXL" depends on MTD_CFI && TQM8xxL diff --git a/drivers/mtd/maps/Makefile b/drivers/mtd/maps/Makefile index 8bae7f9850c..5beb0662d72 100644 --- a/drivers/mtd/maps/Makefile +++ b/drivers/mtd/maps/Makefile @@ -50,7 +50,6 @@ obj-$(CONFIG_MTD_UCLINUX) += uclinux.o obj-$(CONFIG_MTD_NETtel) += nettel.o obj-$(CONFIG_MTD_SCB2_FLASH) += scb2_flash.o obj-$(CONFIG_MTD_H720X) += h720x-flash.o -obj-$(CONFIG_MTD_SBC8240) += sbc8240.o obj-$(CONFIG_MTD_IXP4XX) += ixp4xx.o obj-$(CONFIG_MTD_IXP2000) += ixp2000.o obj-$(CONFIG_MTD_WRSBC8260) += wr_sbc82xx_flash.o diff --git a/drivers/mtd/maps/sbc8240.c b/drivers/mtd/maps/sbc8240.c index d5374cdcb16..e69de29bb2d 100644 --- a/drivers/mtd/maps/sbc8240.c +++ b/drivers/mtd/maps/sbc8240.c @@ -1,250 +0,0 @@ -/* - * Handle mapping of the flash memory access routines on the SBC8240 board. - * - * Carolyn Smith, Tektronix, Inc. - * - * This code is GPLed - */ - -/* - * The SBC8240 has 2 flash banks. - * Bank 0 is a 512 KiB AMD AM29F040B; 8 x 64 KiB sectors. - * It contains the U-Boot code (7 sectors) and the environment (1 sector). - * Bank 1 is 4 x 1 MiB AMD AM29LV800BT; 15 x 64 KiB sectors, 1 x 32 KiB sector, - * 2 x 8 KiB sectors, 1 x 16 KiB sectors. - * Both parts are JEDEC compatible. - */ - -#include -#include -#include -#include - -#include -#include -#include - -#ifdef CONFIG_MTD_PARTITIONS -#include -#endif - -#define DEBUG - -#ifdef DEBUG -# define debugk(fmt,args...) printk(fmt ,##args) -#else -# define debugk(fmt,args...) -#endif - - -#define WINDOW_ADDR0 0xFFF00000 /* 512 KiB */ -#define WINDOW_SIZE0 0x00080000 -#define BUSWIDTH0 1 - -#define WINDOW_ADDR1 0xFF000000 /* 4 MiB */ -#define WINDOW_SIZE1 0x00400000 -#define BUSWIDTH1 8 - -#define MSG_PREFIX "sbc8240:" /* prefix for our printk()'s */ -#define MTDID "sbc8240-%d" /* for mtdparts= partitioning */ - - -static struct map_info sbc8240_map[2] = { - { - .name = "sbc8240 Flash Bank #0", - .size = WINDOW_SIZE0, - .bankwidth = BUSWIDTH0, - }, - { - .name = "sbc8240 Flash Bank #1", - .size = WINDOW_SIZE1, - .bankwidth = BUSWIDTH1, - } -}; - -#define NUM_FLASH_BANKS ARRAY_SIZE(sbc8240_map) - -/* - * The following defines the partition layout of SBC8240 boards. - * - * See include/linux/mtd/partitions.h for definition of the - * mtd_partition structure. - * - * The *_max_flash_size is the maximum possible mapped flash size - * which is not necessarily the actual flash size. It must correspond - * to the value specified in the mapping definition defined by the - * "struct map_desc *_io_desc" for the corresponding machine. - */ - -#ifdef CONFIG_MTD_PARTITIONS - -static struct mtd_partition sbc8240_uboot_partitions [] = { - /* Bank 0 */ - { - .name = "U-boot", /* U-Boot Firmware */ - .offset = 0, - .size = 0x00070000, /* 7 x 64 KiB sectors */ - .mask_flags = MTD_WRITEABLE, /* force read-only */ - }, - { - .name = "environment", /* U-Boot environment */ - .offset = 0x00070000, - .size = 0x00010000, /* 1 x 64 KiB sector */ - }, -}; - -static struct mtd_partition sbc8240_fs_partitions [] = { - { - .name = "jffs", /* JFFS filesystem */ - .offset = 0, - .size = 0x003C0000, /* 4 * 15 * 64KiB */ - }, - { - .name = "tmp32", - .offset = 0x003C0000, - .size = 0x00020000, /* 4 * 32KiB */ - }, - { - .name = "tmp8a", - .offset = 0x003E0000, - .size = 0x00008000, /* 4 * 8KiB */ - }, - { - .name = "tmp8b", - .offset = 0x003E8000, - .size = 0x00008000, /* 4 * 8KiB */ - }, - { - .name = "tmp16", - .offset = 0x003F0000, - .size = 0x00010000, /* 4 * 16KiB */ - } -}; - -/* trivial struct to describe partition information */ -struct mtd_part_def -{ - int nums; - unsigned char *type; - struct mtd_partition* mtd_part; -}; - -static struct mtd_info *sbc8240_mtd[NUM_FLASH_BANKS]; -static struct mtd_part_def sbc8240_part_banks[NUM_FLASH_BANKS]; - - -#endif /* CONFIG_MTD_PARTITIONS */ - - -static int __init init_sbc8240_mtd (void) -{ - static struct _cjs { - u_long addr; - u_long size; - } pt[NUM_FLASH_BANKS] = { - { - .addr = WINDOW_ADDR0, - .size = WINDOW_SIZE0 - }, - { - .addr = WINDOW_ADDR1, - .size = WINDOW_SIZE1 - }, - }; - - int devicesfound = 0; - int i,j; - - for (i = 0; i < NUM_FLASH_BANKS; i++) { - printk (KERN_NOTICE MSG_PREFIX - "Probing 0x%08lx at 0x%08lx\n", pt[i].size, pt[i].addr); - - sbc8240_map[i].map_priv_1 = - (unsigned long) ioremap (pt[i].addr, pt[i].size); - if (!sbc8240_map[i].map_priv_1) { - printk (MSG_PREFIX "failed to ioremap\n"); - for (j = 0; j < i; j++) { - iounmap((void *) sbc8240_map[j].map_priv_1); - sbc8240_map[j].map_priv_1 = 0; - } - return -EIO; - } - simple_map_init(&sbc8240_mtd[i]); - - sbc8240_mtd[i] = do_map_probe("jedec_probe", &sbc8240_map[i]); - - if (sbc8240_mtd[i]) { - sbc8240_mtd[i]->module = THIS_MODULE; - devicesfound++; - } else { - if (sbc8240_map[i].map_priv_1) { - iounmap((void *) sbc8240_map[i].map_priv_1); - sbc8240_map[i].map_priv_1 = 0; - } - } - } - - if (!devicesfound) { - printk(KERN_NOTICE MSG_PREFIX - "No suppported flash chips found!\n"); - return -ENXIO; - } - -#ifdef CONFIG_MTD_PARTITIONS - sbc8240_part_banks[0].mtd_part = sbc8240_uboot_partitions; - sbc8240_part_banks[0].type = "static image"; - sbc8240_part_banks[0].nums = ARRAY_SIZE(sbc8240_uboot_partitions); - sbc8240_part_banks[1].mtd_part = sbc8240_fs_partitions; - sbc8240_part_banks[1].type = "static file system"; - sbc8240_part_banks[1].nums = ARRAY_SIZE(sbc8240_fs_partitions); - - for (i = 0; i < NUM_FLASH_BANKS; i++) { - - if (!sbc8240_mtd[i]) continue; - if (sbc8240_part_banks[i].nums == 0) { - printk (KERN_NOTICE MSG_PREFIX - "No partition info available, registering whole device\n"); - add_mtd_device(sbc8240_mtd[i]); - } else { - printk (KERN_NOTICE MSG_PREFIX - "Using %s partition definition\n", sbc8240_part_banks[i].mtd_part->name); - add_mtd_partitions (sbc8240_mtd[i], - sbc8240_part_banks[i].mtd_part, - sbc8240_part_banks[i].nums); - } - } -#else - printk(KERN_NOTICE MSG_PREFIX - "Registering %d flash banks at once\n", devicesfound); - - for (i = 0; i < devicesfound; i++) { - add_mtd_device(sbc8240_mtd[i]); - } -#endif /* CONFIG_MTD_PARTITIONS */ - - return devicesfound == 0 ? -ENXIO : 0; -} - -static void __exit cleanup_sbc8240_mtd (void) -{ - int i; - - for (i = 0; i < NUM_FLASH_BANKS; i++) { - if (sbc8240_mtd[i]) { - del_mtd_device (sbc8240_mtd[i]); - map_destroy (sbc8240_mtd[i]); - } - if (sbc8240_map[i].map_priv_1) { - iounmap ((void *) sbc8240_map[i].map_priv_1); - sbc8240_map[i].map_priv_1 = 0; - } - } -} - -module_init (init_sbc8240_mtd); -module_exit (cleanup_sbc8240_mtd); - -MODULE_LICENSE ("GPL"); -MODULE_AUTHOR ("Carolyn Smith "); -MODULE_DESCRIPTION ("MTD map driver for SBC8240 boards"); - -- GitLab From d676c11727815761e41a81b00c054b4bec452ae5 Mon Sep 17 00:00:00 2001 From: Matthias Kaehlcke Date: Tue, 14 Jul 2009 22:04:29 +0200 Subject: [PATCH 0717/1342] mtd: mtdblock: introduce mtdblks_lock The mtdblks array and its content are prone to race conditions. Introduce the mutex mtdblks_lock in order to solve this. [Amended by Artem Bityutskiy] Signed-off-by: Matthias Kaehlcke Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse --- drivers/mtd/mtdblock.c | 16 +++++++++++++++- 1 file changed, 15 insertions(+), 1 deletion(-) diff --git a/drivers/mtd/mtdblock.c b/drivers/mtd/mtdblock.c index 208c6faa035..77db5ce24d9 100644 --- a/drivers/mtd/mtdblock.c +++ b/drivers/mtd/mtdblock.c @@ -29,6 +29,8 @@ static struct mtdblk_dev { enum { STATE_EMPTY, STATE_CLEAN, STATE_DIRTY } cache_state; } *mtdblks[MAX_MTD_DEVICES]; +static struct mutex mtdblks_lock; + /* * Cache stuff... * @@ -270,15 +272,19 @@ static int mtdblock_open(struct mtd_blktrans_dev *mbd) DEBUG(MTD_DEBUG_LEVEL1,"mtdblock_open\n"); + mutex_lock(&mtdblks_lock); if (mtdblks[dev]) { mtdblks[dev]->count++; + mutex_unlock(&mtdblks_lock); return 0; } /* OK, it's not open. Create cache info for it */ mtdblk = kzalloc(sizeof(struct mtdblk_dev), GFP_KERNEL); - if (!mtdblk) + if (!mtdblk) { + mutex_unlock(&mtdblks_lock); return -ENOMEM; + } mtdblk->count = 1; mtdblk->mtd = mtd; @@ -291,6 +297,7 @@ static int mtdblock_open(struct mtd_blktrans_dev *mbd) } mtdblks[dev] = mtdblk; + mutex_unlock(&mtdblks_lock); DEBUG(MTD_DEBUG_LEVEL1, "ok\n"); @@ -304,6 +311,8 @@ static int mtdblock_release(struct mtd_blktrans_dev *mbd) DEBUG(MTD_DEBUG_LEVEL1, "mtdblock_release\n"); + mutex_lock(&mtdblks_lock); + mutex_lock(&mtdblk->cache_mutex); write_cached_data(mtdblk); mutex_unlock(&mtdblk->cache_mutex); @@ -316,6 +325,9 @@ static int mtdblock_release(struct mtd_blktrans_dev *mbd) vfree(mtdblk->cache_data); kfree(mtdblk); } + + mutex_unlock(&mtdblks_lock); + DEBUG(MTD_DEBUG_LEVEL1, "ok\n"); return 0; @@ -376,6 +388,8 @@ static struct mtd_blktrans_ops mtdblock_tr = { static int __init init_mtdblock(void) { + mutex_init(&mtdblks_lock); + return register_mtd_blktrans(&mtdblock_tr); } -- GitLab From 126b67b8d26f6623d199aa59279f2e3243f2144c Mon Sep 17 00:00:00 2001 From: Doug Thompson Date: Mon, 3 Aug 2009 12:37:06 +0200 Subject: [PATCH 0718/1342] amd64_edac: fix ECC checking On the good path of BIOS enabled ECC and no override, the value returned is 1 by omission and thus is deemed failing by the probe-function. Allow proper module initialization by clearing the retval explicitly. Signed-off-by: Doug Thompson Signed-off-by: Borislav Petkov --- drivers/edac/amd64_edac.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/edac/amd64_edac.c b/drivers/edac/amd64_edac.c index 24964c1d0af..5fa924d61b1 100644 --- a/drivers/edac/amd64_edac.c +++ b/drivers/edac/amd64_edac.c @@ -2977,6 +2977,9 @@ static int amd64_check_ecc_enabled(struct amd64_pvt *pvt) "ECC is enabled by BIOS, Proceeding " "with EDAC module initialization\n"); + /* Signal good ECC status */ + ret = 0; + /* CLEAR the override, since BIOS controlled it */ ecc_enable_override = 0; } -- GitLab From 1c1a90d866c5fb029099b9f0f40534e01b7c4d91 Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Sun, 5 Jul 2009 19:23:30 +0100 Subject: [PATCH 0719/1342] [PATCH] MIPS: Cavium: Move swapped comments to their rightful place. Signed-off-by: Ralf Baechle --- arch/mips/mm/c-octeon.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/mips/mm/c-octeon.c b/arch/mips/mm/c-octeon.c index b165cdcb281..10ab69f7183 100644 --- a/arch/mips/mm/c-octeon.c +++ b/arch/mips/mm/c-octeon.c @@ -289,7 +289,7 @@ static void cache_parity_error_octeon(int non_recoverable) } /** - * Called when the the exception is not recoverable + * Called when the the exception is recoverable */ asmlinkage void cache_parity_error_octeon_recoverable(void) @@ -298,7 +298,7 @@ asmlinkage void cache_parity_error_octeon_recoverable(void) } /** - * Called when the the exception is recoverable + * Called when the the exception is not recoverable */ asmlinkage void cache_parity_error_octeon_non_recoverable(void) -- GitLab From 49316cbf0a9875f102f98dc8b7c80cfa142e33cf Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Mon, 6 Jul 2009 09:13:17 +0100 Subject: [PATCH 0720/1342] MIPS: Eleminate filenames from comments They tend to get not updated when files are moved around or copied and lack any obvious use. While at it zap some only too obvious comments and as per Shinya's suggestion, add a copyright header to extable.c. Signed-off-by: Ralf Baechle Acked-by: Shinya Kuribayashi Acked-by: Thadeu Lima de Souza Cascardo --- arch/mips/dec/ecc-berr.c | 2 -- arch/mips/dec/int-handler.S | 2 -- arch/mips/dec/ioasic-irq.c | 2 -- arch/mips/dec/kn01-berr.c | 2 -- arch/mips/dec/kn02-irq.c | 2 -- arch/mips/dec/kn02xa-berr.c | 2 -- arch/mips/dec/prom/call_o32.S | 2 -- arch/mips/dec/prom/console.c | 2 -- arch/mips/dec/time.c | 2 -- arch/mips/emma/common/Makefile | 3 --- arch/mips/emma/common/prom.c | 3 --- arch/mips/emma/markeins/Makefile | 3 --- arch/mips/emma/markeins/irq.c | 3 --- arch/mips/emma/markeins/led.c | 3 --- arch/mips/emma/markeins/platform.c | 3 --- arch/mips/emma/markeins/setup.c | 3 --- arch/mips/fw/lib/call_o32.S | 2 -- arch/mips/include/asm/emma/emma2rh.h | 3 --- arch/mips/include/asm/emma/markeins.h | 3 --- arch/mips/kernel/irq_txx9.c | 2 -- arch/mips/kernel/proc.c | 2 -- arch/mips/kernel/stacktrace.c | 2 -- arch/mips/mm/extable.c | 6 +++++- arch/mips/pci/fixup-emma2rh.c | 3 --- arch/mips/pci/fixup-sb1250.c | 2 -- arch/mips/pci/ops-emma2rh.c | 3 --- arch/mips/pci/pci-emma2rh.c | 3 --- arch/mips/pci/pci-tx4927.c | 2 -- arch/mips/pci/pci-tx4938.c | 2 -- arch/mips/pci/pci-tx4939.c | 2 -- arch/mips/pmc-sierra/msp71xx/gpio.c | 2 -- arch/mips/pmc-sierra/msp71xx/gpio_extended.c | 2 -- arch/mips/pmc-sierra/yosemite/atmel_read_eeprom.c | 2 -- arch/mips/sibyte/swarm/swarm-i2c.c | 2 -- arch/mips/txx9/generic/mem_tx4927.c | 2 -- arch/mips/txx9/generic/setup.c | 2 -- 36 files changed, 5 insertions(+), 83 deletions(-) diff --git a/arch/mips/dec/ecc-berr.c b/arch/mips/dec/ecc-berr.c index 6a17c9b508e..7abce661b90 100644 --- a/arch/mips/dec/ecc-berr.c +++ b/arch/mips/dec/ecc-berr.c @@ -1,6 +1,4 @@ /* - * linux/arch/mips/dec/ecc-berr.c - * * Bus error event handling code for systems equipped with ECC * handling logic, i.e. DECstation/DECsystem 5000/200 (KN02), * 5000/240 (KN03), 5000/260 (KN05) and DECsystem 5900 (KN03), diff --git a/arch/mips/dec/int-handler.S b/arch/mips/dec/int-handler.S index 00cecdcc75f..82c85281878 100644 --- a/arch/mips/dec/int-handler.S +++ b/arch/mips/dec/int-handler.S @@ -1,6 +1,4 @@ /* - * arch/mips/dec/int-handler.S - * * Copyright (C) 1995, 1996, 1997 Paul M. Antoine and Harald Koerfgen * Copyright (C) 2000, 2001, 2002, 2003, 2005 Maciej W. Rozycki * diff --git a/arch/mips/dec/ioasic-irq.c b/arch/mips/dec/ioasic-irq.c index 3acb133668d..cb41954fc32 100644 --- a/arch/mips/dec/ioasic-irq.c +++ b/arch/mips/dec/ioasic-irq.c @@ -1,6 +1,4 @@ /* - * linux/arch/mips/dec/ioasic-irq.c - * * DEC I/O ASIC interrupts. * * Copyright (c) 2002, 2003 Maciej W. Rozycki diff --git a/arch/mips/dec/kn01-berr.c b/arch/mips/dec/kn01-berr.c index d3b8002bf1e..b0dc6d53edd 100644 --- a/arch/mips/dec/kn01-berr.c +++ b/arch/mips/dec/kn01-berr.c @@ -1,6 +1,4 @@ /* - * linux/arch/mips/dec/kn01-berr.c - * * Bus error event handling code for DECstation/DECsystem 3100 * and 2100 (KN01) systems equipped with parity error detection * logic. diff --git a/arch/mips/dec/kn02-irq.c b/arch/mips/dec/kn02-irq.c index 02439dc0ba8..ed90a8deabc 100644 --- a/arch/mips/dec/kn02-irq.c +++ b/arch/mips/dec/kn02-irq.c @@ -1,6 +1,4 @@ /* - * linux/arch/mips/dec/kn02-irq.c - * * DECstation 5000/200 (KN02) Control and Status Register * interrupts. * diff --git a/arch/mips/dec/kn02xa-berr.c b/arch/mips/dec/kn02xa-berr.c index 5f04545c360..07ca5405d48 100644 --- a/arch/mips/dec/kn02xa-berr.c +++ b/arch/mips/dec/kn02xa-berr.c @@ -1,6 +1,4 @@ /* - * linux/arch/mips/dec/kn02xa-berr.c - * * Bus error event handling code for 5000-series systems equipped * with parity error detection logic, i.e. DECstation/DECsystem * 5000/120, /125, /133 (KN02-BA), 5000/150 (KN04-BA) and Personal diff --git a/arch/mips/dec/prom/call_o32.S b/arch/mips/dec/prom/call_o32.S index e523454bda3..8c8498159e4 100644 --- a/arch/mips/dec/prom/call_o32.S +++ b/arch/mips/dec/prom/call_o32.S @@ -1,6 +1,4 @@ /* - * arch/mips/dec/prom/call_o32.S - * * O32 interface for the 64 (or N32) ABI. * * Copyright (C) 2002 Maciej W. Rozycki diff --git a/arch/mips/dec/prom/console.c b/arch/mips/dec/prom/console.c index 078e1a12421..caa6e047caf 100644 --- a/arch/mips/dec/prom/console.c +++ b/arch/mips/dec/prom/console.c @@ -1,6 +1,4 @@ /* - * arch/mips/dec/prom/console.c - * * DECstation PROM-based early console support. * * Copyright (C) 2004, 2007 Maciej W. Rozycki diff --git a/arch/mips/dec/time.c b/arch/mips/dec/time.c index 1359c03ded5..463136e6685 100644 --- a/arch/mips/dec/time.c +++ b/arch/mips/dec/time.c @@ -1,6 +1,4 @@ /* - * linux/arch/mips/dec/time.c - * * Copyright (C) 1991, 1992, 1995 Linus Torvalds * Copyright (C) 2000, 2003 Maciej W. Rozycki * diff --git a/arch/mips/emma/common/Makefile b/arch/mips/emma/common/Makefile index c392d28c1ef..f27d84d1904 100644 --- a/arch/mips/emma/common/Makefile +++ b/arch/mips/emma/common/Makefile @@ -1,7 +1,4 @@ # -# arch/mips/emma2rh/common/Makefile -# Makefile for the common code of NEC EMMA2RH based board. -# # Copyright (C) NEC Electronics Corporation 2005-2006 # # This program is free software; you can redistribute it and/or modify diff --git a/arch/mips/emma/common/prom.c b/arch/mips/emma/common/prom.c index 120f53fbdb4..708f0876140 100644 --- a/arch/mips/emma/common/prom.c +++ b/arch/mips/emma/common/prom.c @@ -1,7 +1,4 @@ /* - * arch/mips/emma2rh/common/prom.c - * This file is prom file. - * * Copyright (C) NEC Electronics Corporation 2004-2006 * * This file is based on the arch/mips/ddb5xxx/common/prom.c diff --git a/arch/mips/emma/markeins/Makefile b/arch/mips/emma/markeins/Makefile index 16e0017ba91..f8ba2508fa2 100644 --- a/arch/mips/emma/markeins/Makefile +++ b/arch/mips/emma/markeins/Makefile @@ -1,7 +1,4 @@ # -# arch/mips/emma2rh/markeins/Makefile -# Makefile for the common code of NEC EMMA2RH based board. -# # Copyright (C) NEC Electronics Corporation 2005-2006 # # This program is free software; you can redistribute it and/or modify diff --git a/arch/mips/emma/markeins/irq.c b/arch/mips/emma/markeins/irq.c index 43828ae796e..9504b7ee0b7 100644 --- a/arch/mips/emma/markeins/irq.c +++ b/arch/mips/emma/markeins/irq.c @@ -1,7 +1,4 @@ /* - * arch/mips/emma2rh/markeins/irq.c - * This file defines the irq handler for EMMA2RH. - * * Copyright (C) NEC Electronics Corporation 2004-2006 * * This file is based on the arch/mips/ddb5xxx/ddb5477/irq.c diff --git a/arch/mips/emma/markeins/led.c b/arch/mips/emma/markeins/led.c index 377a181b656..49755896857 100644 --- a/arch/mips/emma/markeins/led.c +++ b/arch/mips/emma/markeins/led.c @@ -1,7 +1,4 @@ /* - * arch/mips/emma2rh/markeins/led.c - * This file defines the led display for Mark-eins. - * * Copyright (C) NEC Electronics Corporation 2004-2006 * * This program is free software; you can redistribute it and/or modify diff --git a/arch/mips/emma/markeins/platform.c b/arch/mips/emma/markeins/platform.c index 80ae12ef87d..b05b08b92a3 100644 --- a/arch/mips/emma/markeins/platform.c +++ b/arch/mips/emma/markeins/platform.c @@ -1,7 +1,4 @@ /* - * arch/mips/emma2rh/markeins/platofrm.c - * This file sets up platform devices for EMMA2RH Mark-eins. - * * Copyright(C) MontaVista Software Inc, 2006 * * Author: dmitry pervushin diff --git a/arch/mips/emma/markeins/setup.c b/arch/mips/emma/markeins/setup.c index 67f45650008..335dc8c1a1b 100644 --- a/arch/mips/emma/markeins/setup.c +++ b/arch/mips/emma/markeins/setup.c @@ -1,7 +1,4 @@ /* - * arch/mips/emma2rh/markeins/setup.c - * This file is setup for EMMA2RH Mark-eins. - * * Copyright (C) NEC Electronics Corporation 2004-2006 * * This file is based on the arch/mips/ddb5xxx/ddb5477/setup.c. diff --git a/arch/mips/fw/lib/call_o32.S b/arch/mips/fw/lib/call_o32.S index bdf7d1d4081..e0a68713b3c 100644 --- a/arch/mips/fw/lib/call_o32.S +++ b/arch/mips/fw/lib/call_o32.S @@ -1,6 +1,4 @@ /* - * arch/mips/dec/prom/call_o32.S - * * O32 interface for the 64 (or N32) ABI. * * Copyright (C) 2002 Maciej W. Rozycki diff --git a/arch/mips/include/asm/emma/emma2rh.h b/arch/mips/include/asm/emma/emma2rh.h index 30aea91de62..2afb2fe11b3 100644 --- a/arch/mips/include/asm/emma/emma2rh.h +++ b/arch/mips/include/asm/emma/emma2rh.h @@ -1,7 +1,4 @@ /* - * arch/mips/include/asm/emma/emma2rh.h - * This file is EMMA2RH common header. - * * Copyright (C) NEC Electronics Corporation 2005-2006 * * This file based on include/asm-mips/ddb5xxx/ddb5xxx.h diff --git a/arch/mips/include/asm/emma/markeins.h b/arch/mips/include/asm/emma/markeins.h index 973b0628490..2618bf23024 100644 --- a/arch/mips/include/asm/emma/markeins.h +++ b/arch/mips/include/asm/emma/markeins.h @@ -1,7 +1,4 @@ /* - * include/asm-mips/emma2rh/markeins.h - * This file is EMMA2RH board depended header. - * * Copyright (C) NEC Electronics Corporation 2005-2006 * * This file based on include/asm-mips/ddb5xxx/ddb5xxx.h diff --git a/arch/mips/kernel/irq_txx9.c b/arch/mips/kernel/irq_txx9.c index a4d1462c27f..9b78029bea7 100644 --- a/arch/mips/kernel/irq_txx9.c +++ b/arch/mips/kernel/irq_txx9.c @@ -1,6 +1,4 @@ /* - * linux/arch/mips/kernel/irq_txx9.c - * * Based on linux/arch/mips/jmr3927/rbhma3100/irq.c, * linux/arch/mips/tx4927/common/tx4927_irq.c, * linux/arch/mips/tx4938/common/irq.c diff --git a/arch/mips/kernel/proc.c b/arch/mips/kernel/proc.c index e0a4ac18fa0..26109c4d517 100644 --- a/arch/mips/kernel/proc.c +++ b/arch/mips/kernel/proc.c @@ -1,6 +1,4 @@ /* - * linux/arch/mips/kernel/proc.c - * * Copyright (C) 1995, 1996, 2001 Ralf Baechle * Copyright (C) 2001, 2004 MIPS Technologies, Inc. * Copyright (C) 2004 Maciej W. Rozycki diff --git a/arch/mips/kernel/stacktrace.c b/arch/mips/kernel/stacktrace.c index 58f5cd76c8c..d52ff77baf3 100644 --- a/arch/mips/kernel/stacktrace.c +++ b/arch/mips/kernel/stacktrace.c @@ -1,6 +1,4 @@ /* - * arch/mips/kernel/stacktrace.c - * * Stack trace management functions * * Copyright (C) 2006 Atsushi Nemoto diff --git a/arch/mips/mm/extable.c b/arch/mips/mm/extable.c index 297fb9f390d..9d25d2ba4b9 100644 --- a/arch/mips/mm/extable.c +++ b/arch/mips/mm/extable.c @@ -1,5 +1,9 @@ /* - * linux/arch/mips/mm/extable.c + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + * + * Copyright (C) 1997, 99, 2001 - 2004 Ralf Baechle */ #include #include diff --git a/arch/mips/pci/fixup-emma2rh.c b/arch/mips/pci/fixup-emma2rh.c index fba5aad00d5..0d9ccf4dfc5 100644 --- a/arch/mips/pci/fixup-emma2rh.c +++ b/arch/mips/pci/fixup-emma2rh.c @@ -1,7 +1,4 @@ /* - * arch/mips/pci/fixup-emma2rh.c - * This file defines the PCI configration. - * * Copyright (C) NEC Electronics Corporation 2004-2006 * * This file is based on the arch/mips/ddb5xxx/ddb5477/pci.c diff --git a/arch/mips/pci/fixup-sb1250.c b/arch/mips/pci/fixup-sb1250.c index 0ad39e53f7b..f0bb9146e6c 100644 --- a/arch/mips/pci/fixup-sb1250.c +++ b/arch/mips/pci/fixup-sb1250.c @@ -1,6 +1,4 @@ /* - * arch/mips/pci/fixup-sb1250.c - * * Copyright (C) 2004, 2006 MIPS Technologies, Inc. All rights reserved. * Author: Maciej W. Rozycki * diff --git a/arch/mips/pci/ops-emma2rh.c b/arch/mips/pci/ops-emma2rh.c index 5947a70b0b7..710aef5c070 100644 --- a/arch/mips/pci/ops-emma2rh.c +++ b/arch/mips/pci/ops-emma2rh.c @@ -1,7 +1,4 @@ /* - * arch/mips/pci/ops-emma2rh.c - * This file defines the PCI operation for EMMA2RH. - * * Copyright (C) NEC Electronics Corporation 2004-2006 * * This file is based on the arch/mips/pci/ops-vr41xx.c diff --git a/arch/mips/pci/pci-emma2rh.c b/arch/mips/pci/pci-emma2rh.c index 2df4190232c..773e34ff4d1 100644 --- a/arch/mips/pci/pci-emma2rh.c +++ b/arch/mips/pci/pci-emma2rh.c @@ -1,7 +1,4 @@ /* - * arch/mips/pci/pci-emma2rh.c - * This file defines the PCI configration. - * * Copyright (C) NEC Electronics Corporation 2004-2006 * * This file is based on the arch/mips/ddb5xxx/ddb5477/pci.c diff --git a/arch/mips/pci/pci-tx4927.c b/arch/mips/pci/pci-tx4927.c index aaa90059679..a5807406a7f 100644 --- a/arch/mips/pci/pci-tx4927.c +++ b/arch/mips/pci/pci-tx4927.c @@ -1,6 +1,4 @@ /* - * linux/arch/mips/pci/pci-tx4927.c - * * Based on linux/arch/mips/txx9/rbtx4938/setup.c, * and RBTX49xx patch from CELF patch archive. * diff --git a/arch/mips/pci/pci-tx4938.c b/arch/mips/pci/pci-tx4938.c index 1ea257bc3b8..20e45f30b2e 100644 --- a/arch/mips/pci/pci-tx4938.c +++ b/arch/mips/pci/pci-tx4938.c @@ -1,6 +1,4 @@ /* - * linux/arch/mips/pci/pci-tx4938.c - * * Based on linux/arch/mips/txx9/rbtx4938/setup.c, * and RBTX49xx patch from CELF patch archive. * diff --git a/arch/mips/pci/pci-tx4939.c b/arch/mips/pci/pci-tx4939.c index 5fecf1cdc32..9ef840693ba 100644 --- a/arch/mips/pci/pci-tx4939.c +++ b/arch/mips/pci/pci-tx4939.c @@ -1,6 +1,4 @@ /* - * linux/arch/mips/pci/pci-tx4939.c - * * Based on linux/arch/mips/txx9/rbtx4939/setup.c, * and RBTX49xx patch from CELF patch archive. * diff --git a/arch/mips/pmc-sierra/msp71xx/gpio.c b/arch/mips/pmc-sierra/msp71xx/gpio.c index 69848c5813e..aaccbe52438 100644 --- a/arch/mips/pmc-sierra/msp71xx/gpio.c +++ b/arch/mips/pmc-sierra/msp71xx/gpio.c @@ -1,6 +1,4 @@ /* - * @file /arch/mips/pmc-sierra/msp71xx/gpio.c - * * Generic PMC MSP71xx GPIO handling. These base gpio are controlled by two * types of registers. The data register sets the output level when in output * mode and when in input mode will contain the value at the input. The config diff --git a/arch/mips/pmc-sierra/msp71xx/gpio_extended.c b/arch/mips/pmc-sierra/msp71xx/gpio_extended.c index fc6dbc6cf1c..2a99f360fae 100644 --- a/arch/mips/pmc-sierra/msp71xx/gpio_extended.c +++ b/arch/mips/pmc-sierra/msp71xx/gpio_extended.c @@ -1,6 +1,4 @@ /* - * @file /arch/mips/pmc-sierra/msp71xx/gpio_extended.c - * * Generic PMC MSP71xx EXTENDED (EXD) GPIO handling. The extended gpio is * a set of hardware registers that have no need for explicit locking as * it is handled by unique method of writing individual set/clr bits. diff --git a/arch/mips/pmc-sierra/yosemite/atmel_read_eeprom.c b/arch/mips/pmc-sierra/yosemite/atmel_read_eeprom.c index caf5e9a0acc..fc990cb3194 100644 --- a/arch/mips/pmc-sierra/yosemite/atmel_read_eeprom.c +++ b/arch/mips/pmc-sierra/yosemite/atmel_read_eeprom.c @@ -1,6 +1,4 @@ /* - * arch/mips/pmc-sierra/yosemite/atmel_read_eeprom.c - * * Copyright (C) 2003 PMC-Sierra Inc. * Author: Manish Lachwani (lachwani@pmc-sierra.com) * diff --git a/arch/mips/sibyte/swarm/swarm-i2c.c b/arch/mips/sibyte/swarm/swarm-i2c.c index 4282ac9d01d..062505054d4 100644 --- a/arch/mips/sibyte/swarm/swarm-i2c.c +++ b/arch/mips/sibyte/swarm/swarm-i2c.c @@ -1,6 +1,4 @@ /* - * arch/mips/sibyte/swarm/swarm-i2c.c - * * Broadcom BCM91250A (SWARM), etc. I2C platform setup. * * Copyright (c) 2008 Maciej W. Rozycki diff --git a/arch/mips/txx9/generic/mem_tx4927.c b/arch/mips/txx9/generic/mem_tx4927.c index ef6ea6e9787..70f9626f822 100644 --- a/arch/mips/txx9/generic/mem_tx4927.c +++ b/arch/mips/txx9/generic/mem_tx4927.c @@ -1,6 +1,4 @@ /* - * linux/arch/mips/txx9/generic/mem_tx4927.c - * * common tx4927 memory interface * * Author: MontaVista Software, Inc. diff --git a/arch/mips/txx9/generic/setup.c b/arch/mips/txx9/generic/setup.c index 3b7d77d61ce..a205e2ba8e7 100644 --- a/arch/mips/txx9/generic/setup.c +++ b/arch/mips/txx9/generic/setup.c @@ -1,6 +1,4 @@ /* - * linux/arch/mips/txx9/generic/setup.c - * * Based on linux/arch/mips/txx9/rbtx4938/setup.c, * and RBTX49xx patch from CELF patch archive. * -- GitLab From a887b4dada2f23b2ff2aa725e0509c92dc652597 Mon Sep 17 00:00:00 2001 From: Akinobu Mita Date: Sat, 4 Jul 2009 01:33:09 +0900 Subject: [PATCH 0721/1342] MIPS: Drop mmap_sem in pagefault oom path Fix the pagefault oom path which does not drop mm->mmap_sem. This was introduced by commit c7c1e3846bac1e4b8a8941f6a194812e28b0a519 Signed-off-by: Akinobu Mita Signed-off-by: Ralf Baechle --- arch/mips/mm/fault.c | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/mips/mm/fault.c b/arch/mips/mm/fault.c index 6751ce9ede9..f956ecbb813 100644 --- a/arch/mips/mm/fault.c +++ b/arch/mips/mm/fault.c @@ -171,6 +171,7 @@ out_of_memory: * We ran out of memory, call the OOM killer, and return the userspace * (which will retry the fault, or kill us if we got oom-killed). */ + up_read(&mm->mmap_sem); pagefault_out_of_memory(); return; -- GitLab From 7d35cdc07dd26eb6667f66f8e2f43f833a926ecf Mon Sep 17 00:00:00 2001 From: Alexander Clouter Date: Sun, 5 Jul 2009 12:00:55 +0100 Subject: [PATCH 0722/1342] MIPS: Fix compile for !CONFIG_SMP Commit fc03bc1715ca0ad4ccfe97aab16bcc9e7129c1a4 breaks compiling MIPS with SMP disabled. This patch fixes that. Signed-off-by: Alexander Clouter Signed-off-by: Ralf Baechle --- arch/mips/include/asm/gic.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/mips/include/asm/gic.h b/arch/mips/include/asm/gic.h index 10292e37c1f..a8f57341f12 100644 --- a/arch/mips/include/asm/gic.h +++ b/arch/mips/include/asm/gic.h @@ -20,7 +20,7 @@ #define GIC_TRIG_EDGE 1 #define GIC_TRIG_LEVEL 0 -#if CONFIG_SMP +#ifdef CONFIG_SMP #define GIC_NUM_INTRS (24 + NR_CPUS * 2) #else #define GIC_NUM_INTRS 32 -- GitLab From 78fe01a5a80da4621321a1dc199c3a0875e2fbb0 Mon Sep 17 00:00:00 2001 From: Yoichi Yuasa Date: Wed, 8 Jul 2009 15:08:19 +0900 Subject: [PATCH 0723/1342] MIPS: MIPSsim: Fix unbalance brace in mipssim get_c0_compare_int() cc1: warnings being treated as errors arch/mips/mipssim/sim_time.c: In function 'get_c0_compare_int': arch/mips/mipssim/sim_time.c:103: warning: ISO C90 forbids mixed declarations and code arch/mips/mipssim/sim_time.c:116: error: expected declaration or statement at end of input make[1]: *** [arch/mips/mipssim/sim_time.o] Error 1 Signed-off-by: Yoichi Yuasa Signed-off-by: Ralf Baechle --- arch/mips/mipssim/sim_time.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/arch/mips/mipssim/sim_time.c b/arch/mips/mipssim/sim_time.c index 0cea932f124..5492c42f765 100644 --- a/arch/mips/mipssim/sim_time.c +++ b/arch/mips/mipssim/sim_time.c @@ -89,13 +89,13 @@ unsigned __cpuinit get_c0_compare_int(void) if (cpu_has_veic) { set_vi_handler(MSC01E_INT_CPUCTR, mips_timer_dispatch); mips_cpu_timer_irq = MSC01E_INT_BASE + MSC01E_INT_CPUCTR; - } else { -#endif - { - if (cpu_has_vint) - set_vi_handler(cp0_compare_irq, mips_timer_dispatch); - mips_cpu_timer_irq = MIPS_CPU_IRQ_BASE + cp0_compare_irq; + + return mips_cpu_timer_irq; } +#endif + if (cpu_has_vint) + set_vi_handler(cp0_compare_irq, mips_timer_dispatch); + mips_cpu_timer_irq = MIPS_CPU_IRQ_BASE + cp0_compare_irq; return mips_cpu_timer_irq; } -- GitLab From 1de010a2702eb21d90883b83bf8c737d5e69d234 Mon Sep 17 00:00:00 2001 From: Huang Weiyi Date: Thu, 9 Jul 2009 06:14:37 +0800 Subject: [PATCH 0724/1342] MIPS: AR7: Remove unused inclusions of . Signed-off-by: Huang Weiyi Signed-off-by: Ralf Baechle --- arch/mips/ar7/platform.c | 1 - arch/mips/ar7/setup.c | 1 - 2 files changed, 2 deletions(-) diff --git a/arch/mips/ar7/platform.c b/arch/mips/ar7/platform.c index 54224496178..c4d71fb18de 100644 --- a/arch/mips/ar7/platform.c +++ b/arch/mips/ar7/platform.c @@ -28,7 +28,6 @@ #include #include #include -#include #include #include #include diff --git a/arch/mips/ar7/setup.c b/arch/mips/ar7/setup.c index 6ebb5f16d96..39f6b5b9646 100644 --- a/arch/mips/ar7/setup.c +++ b/arch/mips/ar7/setup.c @@ -15,7 +15,6 @@ * with this program; if not, write to the Free Software Foundation, Inc., * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA. */ -#include #include #include #include -- GitLab From 484889fc85a223ef56edc31828b86751b2296b7c Mon Sep 17 00:00:00 2001 From: David Daney Date: Wed, 8 Jul 2009 10:07:50 -0700 Subject: [PATCH 0725/1342] MIPS: Avoid clobbering struct pt_regs in kthreads The resume() implementation octeon_switch.S examines the saved cp0_status register. We were clobbering the entire pt_regs structure in kernel threads leading to random crashes. When switching away from a kernel thread, the saved cp0_status is examined and if bit 30 is set it is cleared and the CP2 state saved into the pt_regs structure. Since the kernel thread stack overlaid the pt_regs structure this resulted in a corrupt stack. When the kthread with the corrupt stack was resumed, it could crash if it used any of the data in the stack that was clobbered. We fix it by moving the kernel thread stack down so it doesn't overlay pt_regs. Signed-off-by: David Daney Signed-off-by: Ralf Baechle --- arch/mips/include/asm/processor.h | 5 +++-- arch/mips/kernel/head.S | 3 ++- arch/mips/kernel/process.c | 4 +++- 3 files changed, 8 insertions(+), 4 deletions(-) diff --git a/arch/mips/include/asm/processor.h b/arch/mips/include/asm/processor.h index 0f926aa0cb4..087a8884ef0 100644 --- a/arch/mips/include/asm/processor.h +++ b/arch/mips/include/asm/processor.h @@ -311,8 +311,9 @@ extern void start_thread(struct pt_regs * regs, unsigned long pc, unsigned long unsigned long get_wchan(struct task_struct *p); -#define __KSTK_TOS(tsk) ((unsigned long)task_stack_page(tsk) + THREAD_SIZE - 32) -#define task_pt_regs(tsk) ((struct pt_regs *)__KSTK_TOS(tsk) - 1) +#define __KSTK_TOS(tsk) ((unsigned long)task_stack_page(tsk) + \ + THREAD_SIZE - 32 - sizeof(struct pt_regs)) +#define task_pt_regs(tsk) ((struct pt_regs *)__KSTK_TOS(tsk)) #define KSTK_EIP(tsk) (task_pt_regs(tsk)->cp0_epc) #define KSTK_ESP(tsk) (task_pt_regs(tsk)->regs[29]) #define KSTK_STATUS(tsk) (task_pt_regs(tsk)->cp0_status) diff --git a/arch/mips/kernel/head.S b/arch/mips/kernel/head.S index 492a0a8d70f..531ce7b1612 100644 --- a/arch/mips/kernel/head.S +++ b/arch/mips/kernel/head.S @@ -188,7 +188,8 @@ NESTED(kernel_entry, 16, sp) # kernel entry point MTC0 zero, CP0_CONTEXT # clear context register PTR_LA $28, init_thread_union - PTR_LI sp, _THREAD_SIZE - 32 + /* Set the SP after an empty pt_regs. */ + PTR_LI sp, _THREAD_SIZE - 32 - PT_SIZE PTR_ADDU sp, $28 set_saved_sp sp, t0, t1 PTR_SUBU sp, 4 * SZREG # init stack pointer diff --git a/arch/mips/kernel/process.c b/arch/mips/kernel/process.c index c09d681b718..f3d73e1831c 100644 --- a/arch/mips/kernel/process.c +++ b/arch/mips/kernel/process.c @@ -115,7 +115,7 @@ int copy_thread(unsigned long clone_flags, unsigned long usp, { struct thread_info *ti = task_thread_info(p); struct pt_regs *childregs; - long childksp; + unsigned long childksp; p->set_child_tid = p->clear_child_tid = NULL; childksp = (unsigned long)task_stack_page(p) + THREAD_SIZE - 32; @@ -132,6 +132,8 @@ int copy_thread(unsigned long clone_flags, unsigned long usp, /* set up new TSS. */ childregs = (struct pt_regs *) childksp - 1; + /* Put the stack after the struct pt_regs. */ + childksp = (unsigned long) childregs; *childregs = *regs; childregs->regs[7] = 0; /* Clear error flag */ -- GitLab From 008ee96f1204225503934cb57ac38c49f519c7ab Mon Sep 17 00:00:00 2001 From: Raghu Gandham Date: Wed, 8 Jul 2009 17:00:44 -0700 Subject: [PATCH 0726/1342] [PATCH] MIPS: SMTC: Fix compile error Commit fc03bc1715ca0ad4ccfe97aab16bcc9e7129c1a4 breaks when SMTC support is enabled on Malta. Signed-off-by: Raghu Gandham Signed-off-by: Ralf Baechle --- arch/mips/mti-malta/malta-int.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/mips/mti-malta/malta-int.c b/arch/mips/mti-malta/malta-int.c index a8756f82c31..3e0a9b35ba5 100644 --- a/arch/mips/mti-malta/malta-int.c +++ b/arch/mips/mti-malta/malta-int.c @@ -331,6 +331,7 @@ static struct irqaction irq_call = { .flags = IRQF_DISABLED|IRQF_PERCPU, .name = "IPI_call" }; +#endif /* CONFIG_MIPS_MT_SMP */ static int gic_resched_int_base; static int gic_call_int_base; @@ -346,7 +347,6 @@ unsigned int plat_ipi_resched_int_xlate(unsigned int cpu) { return GIC_RESCHED_INT(cpu); } -#endif /* CONFIG_MIPS_MT_SMP */ static struct irqaction i8259irq = { .handler = no_action, -- GitLab From d8e5f9fe5dab0e07985f2456cb6cc57788f53131 Mon Sep 17 00:00:00 2001 From: Kurt Martin Date: Wed, 8 Jul 2009 19:22:35 -0700 Subject: [PATCH 0727/1342] MIPS: SMTC: Move cross VPE writes to after a TC is assigned to VPE. Signed-off-by: Chris Dearman Signed-off-by: Raghu Gandham Signed-off-by: Ralf Baechle --- arch/mips/kernel/smtc.c | 13 ++++++++----- 1 file changed, 8 insertions(+), 5 deletions(-) diff --git a/arch/mips/kernel/smtc.c b/arch/mips/kernel/smtc.c index 8a0626cbb10..c16bb6d6c25 100644 --- a/arch/mips/kernel/smtc.c +++ b/arch/mips/kernel/smtc.c @@ -465,11 +465,8 @@ void smtc_prepare_cpus(int cpus) smtc_configure_tlb(); for (tc = 0, vpe = 0 ; (vpe < nvpe) && (tc < ntc) ; vpe++) { - /* - * Set the MVP bits. - */ - settc(tc); - write_vpe_c0_vpeconf0(read_vpe_c0_vpeconf0() | VPECONF0_MVP); + if (tcpervpe[vpe] == 0) + continue; if (vpe != 0) printk(", "); printk("VPE %d: TC", vpe); @@ -487,6 +484,12 @@ void smtc_prepare_cpus(int cpus) tc++; } if (vpe != 0) { + /* + * Allow this VPE to control others. + */ + write_vpe_c0_vpeconf0(read_vpe_c0_vpeconf0() | + VPECONF0_MVP); + /* * Clear any stale software interrupts from VPE's Cause */ -- GitLab From 0e66fff883ef1b6e4c5031e8add8827cd0e2a195 Mon Sep 17 00:00:00 2001 From: Gabor Juhos Date: Mon, 13 Jul 2009 11:14:24 +0200 Subject: [PATCH 0728/1342] MIPS: Fix loading of modules with unresolved weak symbols Loading of modules with unresolved weak symbols fails on MIPS since '88173507e4fc1e7ecd111b0565e8cba0cb7dae6d'. Modules: handle symbols that have a zero value The module subsystem cannot handle symbols that are zero. If symbols are present that have a zero value then the module resolver prints out a message that these symbols are unresolved. We have to use IS_ERR_VALUE() to check that a symbol has been resolved or not. Signed-off-by: Gabor Juhos Signed-off-by: Ralf Baechle --- arch/mips/kernel/module.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/mips/kernel/module.c b/arch/mips/kernel/module.c index 3e9100dcc12..e465851a616 100644 --- a/arch/mips/kernel/module.c +++ b/arch/mips/kernel/module.c @@ -301,7 +301,7 @@ int apply_relocate(Elf_Shdr *sechdrs, const char *strtab, /* This is the symbol it is referring to */ sym = (Elf_Sym *)sechdrs[symindex].sh_addr + ELF_MIPS_R_SYM(rel[i]); - if (!sym->st_value) { + if (IS_ERR_VALUE(sym->st_value)) { /* Ignore unresolved weak symbol */ if (ELF_ST_BIND(sym->st_info) == STB_WEAK) continue; @@ -341,7 +341,7 @@ int apply_relocate_add(Elf_Shdr *sechdrs, const char *strtab, /* This is the symbol it is referring to */ sym = (Elf_Sym *)sechdrs[symindex].sh_addr + ELF_MIPS_R_SYM(rel[i]); - if (!sym->st_value) { + if (IS_ERR_VALUE(sym->st_value)) { /* Ignore unresolved weak symbol */ if (ELF_ST_BIND(sym->st_info) == STB_WEAK) continue; -- GitLab From 4824f20c8b3adcbc5067c1bdd88408ee68da6bb2 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Mon, 27 Apr 2009 16:59:48 +0200 Subject: [PATCH 0729/1342] MIPS: MSP71xx: fix build failures on msp_irq_slp.c Trying to build MSP4200 VoIP defconfig also fails on msp_irq_slp.c with a non-existing reference to mask_slp_irq, which is in turn mask_msp_slp_irq. Passed that, we will also miss a comma when calling set_irq_chip_and_handler. This patch fixes both issues. Signed-off-by: Florian Fainelli Acked-by: Shane McDonald Signed-off-by: Ralf Baechle --- arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c b/arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c index f5f1b8d2bb9..66f6f8505e7 100644 --- a/arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c +++ b/arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c @@ -45,7 +45,7 @@ static inline void mask_msp_slp_irq(unsigned int irq) */ static inline void ack_msp_slp_irq(unsigned int irq) { - mask_slp_irq(irq); + mask_msp_slp_irq(irq); /* * only really necessary for 18, 16-14 and sometimes 3:0 (since @@ -79,7 +79,7 @@ void __init msp_slp_irq_init(void) /* initialize all the IRQ descriptors */ for (i = MSP_SLP_INTBASE; i < MSP_PER_INTBASE + 32; i++) - set_irq_chip_and_handler(i, &msp_slp_irq_controller + set_irq_chip_and_handler(i, &msp_slp_irq_controller, handle_level_irq); } -- GitLab From 6577890fd68c2671850214663dd9ae97feacbc47 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Mon, 27 Apr 2009 16:47:23 +0200 Subject: [PATCH 0730/1342] MIPS: MSPxxxx: define MIPS34K_MISSED_ITLB_WAR for other PMC-Sierra SoC Trying to build a PMC-Sierra MSP4200 VoIP gateway defconfig will not work since MIPS34K_MISSED_ITLB_WAR is not defined for all boards supported within pmc-serria/msp71xx. This patch defines MIPS34K_MISSED_ITLB_WAR to prevent such build failures: CHK include/linux/version.h CHK include/linux/utsrelease.h SYMLINK include/asm -> include/asm-mips CC arch/mips/kernel/asm-offsets.s In file included fromlinux-msp71xx/linux-2.6.29/arch/mips/include/asm/bitops.h:24, from include/linux/bitops.h:17, from include/linux/kernel.h:15, from include/linux/sched.h:52, from arch/mips/kernel/asm-offsets.c:13: linux-msp71xx/linux-2.6.29/arch/mips/include/asm/war.h:241:2: error: #error Check setting of MIPS34K_MISSED_ITLB_WAR for your platform This fixes a compile error when building for the MSP4200 boards. Identical patches to fix this were send by Florian Fainelli Shane McDonald Signed-off-by: Florian Fainelli Signed-off-by: Ralf Baechle --- arch/mips/include/asm/pmc-sierra/msp71xx/war.h | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/mips/include/asm/pmc-sierra/msp71xx/war.h b/arch/mips/include/asm/pmc-sierra/msp71xx/war.h index 0bf48fc1892..9e2ee429c52 100644 --- a/arch/mips/include/asm/pmc-sierra/msp71xx/war.h +++ b/arch/mips/include/asm/pmc-sierra/msp71xx/war.h @@ -23,6 +23,8 @@ #if defined(CONFIG_PMC_MSP7120_EVAL) || defined(CONFIG_PMC_MSP7120_GW) || \ defined(CONFIG_PMC_MSP7120_FPGA) #define MIPS34K_MISSED_ITLB_WAR 1 +#else +#define MIPS34K_MISSED_ITLB_WAR 0 #endif #endif /* __ASM_MIPS_PMC_SIERRA_WAR_H */ -- GitLab From 0ca71737fee65521ede964afbd2d5484976ed0ed Mon Sep 17 00:00:00 2001 From: Shane McDonald Date: Sun, 12 Jul 2009 10:42:06 -0600 Subject: [PATCH 0731/1342] MIPS: Simplify and correct interrupt handling for MSP4200 The current interrupt handling code for the MSP4200 always masks an interrupt before acknowledging it. This is not required, as that will be handled by the level interrupt handler. This change simplifies the MSP4200 code to remove the masking in the ack routine, and makes sure that the minimum required operation is performed for masking and acking, rather than always both masking and acking the interrupt. Signed-off-by: Shane McDonald Signed-off-by: Ralf Baechle --- arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c | 10 +--------- 1 file changed, 1 insertion(+), 9 deletions(-) diff --git a/arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c b/arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c index 66f6f8505e7..61f39023234 100644 --- a/arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c +++ b/arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c @@ -45,13 +45,6 @@ static inline void mask_msp_slp_irq(unsigned int irq) */ static inline void ack_msp_slp_irq(unsigned int irq) { - mask_msp_slp_irq(irq); - - /* - * only really necessary for 18, 16-14 and sometimes 3:0 (since - * these can be edge sensitive) but it doesn't hurt for the others. - */ - /* check for PER interrupt range */ if (irq < MSP_PER_INTBASE) *SLP_INT_STS_REG = (1 << (irq - MSP_SLP_INTBASE)); @@ -62,8 +55,7 @@ static inline void ack_msp_slp_irq(unsigned int irq) static struct irq_chip msp_slp_irq_controller = { .name = "MSP_SLP", .ack = ack_msp_slp_irq, - .mask = ack_msp_slp_irq, - .mask_ack = ack_msp_slp_irq, + .mask = mask_msp_slp_irq, .unmask = unmask_msp_slp_irq, }; -- GitLab From 3e6e92183118d26d856e8efb549987164d1b49b4 Mon Sep 17 00:00:00 2001 From: Atsushi Nemoto Date: Wed, 15 Jul 2009 22:03:56 +0900 Subject: [PATCH 0732/1342] MIPS: RBTX4939: Fix IOC pin-enable register updating The rbtx4939_update_ioc_pen() expects txx9_ce_res[] already initialized. Call it after tx4939_setup(). Signed-off-by: Atsushi Nemoto Signed-off-by: Ralf Baechle --- arch/mips/txx9/rbtx4939/setup.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/mips/txx9/rbtx4939/setup.c b/arch/mips/txx9/rbtx4939/setup.c index c033ffe71cd..b0c241ecf60 100644 --- a/arch/mips/txx9/rbtx4939/setup.c +++ b/arch/mips/txx9/rbtx4939/setup.c @@ -512,10 +512,10 @@ static void __init rbtx4939_setup(void) rbtx4939_ebusc_setup(); /* always enable ATA0 */ txx9_set64(&tx4939_ccfgptr->pcfg, TX4939_PCFG_ATA0MODE); - rbtx4939_update_ioc_pen(); if (txx9_master_clock == 0) txx9_master_clock = 20000000; tx4939_setup(); + rbtx4939_update_ioc_pen(); #ifdef HAVE_RBTX4939_IOSWAB ioswabw = rbtx4939_ioswabw; __mem_ioswabw = rbtx4939_mem_ioswabw; -- GitLab From 838c05705ef8c110037a713526bb18762db0a241 Mon Sep 17 00:00:00 2001 From: David Daney Date: Tue, 14 Jul 2009 18:16:50 -0700 Subject: [PATCH 0733/1342] MIPS: Octeon PCIe: Make hardware and software bus numbers match. Some SiliconImage PCIe SATA controlers are not detected when the bus numbers differ. Signed-off-by: David Daney Signed-off-by: Ralf Baechle --- arch/mips/pci/pcie-octeon.c | 31 +++++++++++++++++-------------- 1 file changed, 17 insertions(+), 14 deletions(-) diff --git a/arch/mips/pci/pcie-octeon.c b/arch/mips/pci/pcie-octeon.c index 75262247f3e..6aa5c542d52 100644 --- a/arch/mips/pci/pcie-octeon.c +++ b/arch/mips/pci/pcie-octeon.c @@ -1040,19 +1040,29 @@ static inline int octeon_pcie_read_config(int pcie_port, struct pci_bus *bus, int bus_number = bus->number; /* - * We need to force the bus number to be zero on the root - * bus. Linux numbers the 2nd root bus to start after all - * buses on root 0. + * For the top level bus make sure our hardware bus number + * matches the software one. */ - if (bus->parent == NULL) - bus_number = 0; + if (bus->parent == NULL) { + union cvmx_pciercx_cfg006 pciercx_cfg006; + pciercx_cfg006.u32 = cvmx_pcie_cfgx_read(pcie_port, + CVMX_PCIERCX_CFG006(pcie_port)); + if (pciercx_cfg006.s.pbnum != bus_number) { + pciercx_cfg006.s.pbnum = bus_number; + pciercx_cfg006.s.sbnum = bus_number; + pciercx_cfg006.s.subbnum = bus_number; + cvmx_pcie_cfgx_write(pcie_port, + CVMX_PCIERCX_CFG006(pcie_port), + pciercx_cfg006.u32); + } + } /* * PCIe only has a single device connected to Octeon. It is * always device ID 0. Don't bother doing reads for other * device IDs on the first segment. */ - if ((bus_number == 0) && (devfn >> 3 != 0)) + if ((bus->parent == NULL) && (devfn >> 3 != 0)) return PCIBIOS_FUNC_NOT_SUPPORTED; /* @@ -1070,7 +1080,7 @@ static inline int octeon_pcie_read_config(int pcie_port, struct pci_bus *bus, * bridge only respondes to device ID 0, function * 0-1 */ - if ((bus_number == 0) && (devfn >= 2)) + if ((bus->parent == NULL) && (devfn >= 2)) return PCIBIOS_FUNC_NOT_SUPPORTED; /* * The PCI-X slots are device ID 2,3. Choose one of @@ -1167,13 +1177,6 @@ static inline int octeon_pcie_write_config(int pcie_port, struct pci_bus *bus, int size, u32 val) { int bus_number = bus->number; - /* - * We need to force the bus number to be zero on the root - * bus. Linux numbers the 2nd root bus to start after all - * busses on root 0. - */ - if (bus->parent == NULL) - bus_number = 0; switch (size) { case 4: -- GitLab From dd34b5a82feadfaee4f8dea83a694d9349f94a28 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Tue, 21 Jul 2009 12:38:10 +0200 Subject: [PATCH 0734/1342] MIPS: AR7: Fix build warning on memory.c This patch fixes the following build warning: arch/mips/ar7/memory.c: In function 'memsize': arch/mips/ar7/memory.c:55: warning: passing argument 1 of 'writel' makes integer from pointer without a cast Signed-off-by: Florian Fainelli Signed-off-by: Ralf Baechle --- arch/mips/ar7/memory.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/mips/ar7/memory.c b/arch/mips/ar7/memory.c index 46fed44825a..696c723dc6d 100644 --- a/arch/mips/ar7/memory.c +++ b/arch/mips/ar7/memory.c @@ -52,7 +52,7 @@ static int __init memsize(void) size <<= 1; } while (size < (64 << 20)); - writel(tmpaddr, &addr); + writel((u32)tmpaddr, &addr); return size; } -- GitLab From ea85a0e4cc870d2bb92e3b2007007901209bb7de Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Wed, 29 Jul 2009 22:02:53 +0200 Subject: [PATCH 0735/1342] MIPS: Fix read buffer overflow Signed-off-by: Roel Kluin Signed-off-by: Ralf Baechle --- arch/mips/ar7/prom.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/mips/ar7/prom.c b/arch/mips/ar7/prom.c index a320bceb2f9..5ad6f1db656 100644 --- a/arch/mips/ar7/prom.c +++ b/arch/mips/ar7/prom.c @@ -144,7 +144,7 @@ static char * __init lookup_psp_var_map(u8 num) { int i; - for (i = 0; i < sizeof(psp_var_map); i++) + for (i = 0; i < ARRAY_SIZE(psp_var_map); i++) if (psp_var_map[i].num == num) return psp_var_map[i].value; -- GitLab From 50ca961912be315035cb0f3508e35c974851da2a Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Fri, 24 Jul 2009 13:24:15 +0200 Subject: [PATCH 0736/1342] MIPS: AR7: Fix build failures when CONFIG_SERIAL_8250 is not enabled This patch fixes the following build failure when CONFIG_SERIAL_8250 is not enabled in the kernel configuration: arch/mips/ar7/built-in.o: In function 'ar7_register_devices': platform.c:(.init.text+0x61c): undefined reference to 'early_serial_setup' platform.c:(.init.text+0x61c): relocation truncated to fit: R_MIPS_26 against 'early_serial_setup' platform.c:(.init.text+0x68c): undefined reference to 'early_serial_setup' platform.c:(.init.text+0x68c): relocation truncated to fit: R_MIPS_26 against 'early_serial_setup' Signed-off-by: Florian Fainelli Signed-off-by: Ralf Baechle --- arch/mips/ar7/platform.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/arch/mips/ar7/platform.c b/arch/mips/ar7/platform.c index c4d71fb18de..8ef8266e47f 100644 --- a/arch/mips/ar7/platform.c +++ b/arch/mips/ar7/platform.c @@ -480,6 +480,7 @@ static void __init detect_leds(void) static int __init ar7_register_devices(void) { int res; +#ifdef CONFIG_SERIAL_8250 static struct uart_port uart_port[2]; memset(uart_port, 0, sizeof(struct uart_port) * 2); @@ -511,7 +512,7 @@ static int __init ar7_register_devices(void) if (res) return res; } - +#endif /* CONFIG_SERIAL_8250 */ res = platform_device_register(&physmap_flash); if (res) return res; -- GitLab From 8e84c1480d2e7d98d487b567100717b9cc9dcfd7 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Fri, 24 Jul 2009 13:18:16 +0200 Subject: [PATCH 0737/1342] MIPS: AR7: Use DMA_BIT_MASK(nn) instead of deprecated DMA_nnBIT_MASK Signed-off-by: Florian Fainelli Signed-off-by: Ralf Baechle --- arch/mips/ar7/platform.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/mips/ar7/platform.c b/arch/mips/ar7/platform.c index 8ef8266e47f..2ecab615593 100644 --- a/arch/mips/ar7/platform.c +++ b/arch/mips/ar7/platform.c @@ -242,13 +242,13 @@ static struct platform_device physmap_flash = { .num_resources = 1, }; -static u64 cpmac_dma_mask = DMA_32BIT_MASK; +static u64 cpmac_dma_mask = DMA_BIT_MASK(32); static struct platform_device cpmac_low = { .id = 0, .name = "cpmac", .dev = { .dma_mask = &cpmac_dma_mask, - .coherent_dma_mask = DMA_32BIT_MASK, + .coherent_dma_mask = DMA_BIT_MASK(32), .platform_data = &cpmac_low_data, }, .resource = cpmac_low_res, @@ -260,7 +260,7 @@ static struct platform_device cpmac_high = { .name = "cpmac", .dev = { .dma_mask = &cpmac_dma_mask, - .coherent_dma_mask = DMA_32BIT_MASK, + .coherent_dma_mask = DMA_BIT_MASK(32), .platform_data = &cpmac_high_data, }, .resource = cpmac_high_res, -- GitLab From e5b3837a52c7fe5c7086590bed902f0fac5f9ec0 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Fri, 24 Jul 2009 13:18:42 +0200 Subject: [PATCH 0738/1342] MIPS: AR7: Remove unused tnetd7200_get_clock function Signed-off-by: Florian Fainelli Signed-off-by: Ralf Baechle --- arch/mips/ar7/clock.c | 13 ------------- 1 file changed, 13 deletions(-) diff --git a/arch/mips/ar7/clock.c b/arch/mips/ar7/clock.c index 27dc6663f2f..cc65c8eb391 100644 --- a/arch/mips/ar7/clock.c +++ b/arch/mips/ar7/clock.c @@ -264,19 +264,6 @@ static void __init tnetd7300_init_clocks(void) iounmap(bootcr); } -static int tnetd7200_get_clock(int base, struct tnetd7200_clock *clock, - u32 *bootcr, u32 bus_clock) -{ - int divisor = ((readl(&clock->prediv) & 0x1f) + 1) * - ((readl(&clock->postdiv) & 0x1f) + 1); - - if (*bootcr & BOOT_PLL_BYPASS) - return base / divisor; - - return base * ((readl(&clock->mul) & 0xf) + 1) / divisor; -} - - static void tnetd7200_set_clock(int base, struct tnetd7200_clock *clock, int prediv, int postdiv, int postdiv2, int mul, u32 frequency) { -- GitLab From 619e22632ea3110323b1851a7fecb52bf8505fd2 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Fri, 24 Jul 2009 13:19:10 +0200 Subject: [PATCH 0739/1342] MIPS: AR7: Override CFLAGS with -Werror Now that we have removed all warnings from the ar7 board code we can use -Werror like on other MIPS boards. Signed-off-by: Florian Fainelli Signed-off-by: Ralf Baechle --- arch/mips/ar7/Makefile | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/mips/ar7/Makefile b/arch/mips/ar7/Makefile index 7435e44b396..26bc5da1899 100644 --- a/arch/mips/ar7/Makefile +++ b/arch/mips/ar7/Makefile @@ -8,3 +8,4 @@ obj-y := \ platform.o \ gpio.o \ clock.o +EXTRA_CFLAGS += -Werror -- GitLab From a1b021d3992d9be03b0abec1a7ed78e713b94206 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Sat, 1 Aug 2009 23:51:20 +0200 Subject: [PATCH 0740/1342] MIPS: MTX-1: Request button GPIO before setting its direction This patch fixes the following warning at boot time: WARNING: at drivers/gpio/gpiolib.c:83 0x8021d5e0() autorequest GPIO-207 Modules linked in: Call Trace:[<8011e0ec>] 0x8011e0ec [<80110a28>] 0x80110a28 [<80110a28>] 0x80110a28 [..snip..] The current code does not request the GPIO and attempts to set its direction, which is a violation of the GPIO API. This patch also unhardcode the GPIO we request and use the one we defined in the button driver. Signed-off-by: Florian Fainelli Signed-off-by: Ralf Baechle --- arch/mips/alchemy/mtx-1/platform.c | 14 ++++++++++++-- 1 file changed, 12 insertions(+), 2 deletions(-) diff --git a/arch/mips/alchemy/mtx-1/platform.c b/arch/mips/alchemy/mtx-1/platform.c index 8b5914d1241..e30e42add69 100644 --- a/arch/mips/alchemy/mtx-1/platform.c +++ b/arch/mips/alchemy/mtx-1/platform.c @@ -1,7 +1,7 @@ /* * MTX-1 platform devices registration * - * Copyright (C) 2007, Florian Fainelli + * Copyright (C) 2007-2009, Florian Fainelli * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -142,7 +142,17 @@ static struct __initdata platform_device * mtx1_devs[] = { static int __init mtx1_register_devices(void) { - gpio_direction_input(207); + int rc; + + rc = gpio_request(mtx1_gpio_button[0].gpio, + mtx1_gpio_button[0].desc); + if (rc < 0) { + printk(KERN_INFO "mtx1: failed to request %d\n", + mtx1_gpio_button[0].gpio); + goto out; + } + gpio_direction_input(mtx1_gpio_button[0].gpio); +out: return platform_add_devices(mtx1_devs, ARRAY_SIZE(mtx1_devs)); } -- GitLab From 64f1815507f207ec54ee6b9ae69c48bd153e83b4 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Sun, 2 Aug 2009 10:48:08 +0200 Subject: [PATCH 0741/1342] MIPS: Use DIV_ROUND_CLOSEST The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d but is perhaps more readable. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // @haskernel@ @@ #include @depends on haskernel@ expression x,__divisor; @@ - (((x) + ((__divisor) / 2)) / (__divisor)) + DIV_ROUND_CLOSEST(x,__divisor) // Signed-off-by: Julia Lawall Signed-off-by: Ralf Baechle --- arch/mips/nxp/pnx8550/common/time.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/mips/nxp/pnx8550/common/time.c b/arch/mips/nxp/pnx8550/common/time.c index 8df43e9e4d9..18b19278487 100644 --- a/arch/mips/nxp/pnx8550/common/time.c +++ b/arch/mips/nxp/pnx8550/common/time.c @@ -138,7 +138,7 @@ __init void plat_time_init(void) * HZ timer interrupts per second. */ mips_hpt_frequency = 27UL * ((1000000UL * n)/(m * pow2p)); - cpj = (mips_hpt_frequency + HZ / 2) / HZ; + cpj = DIV_ROUND_CLOSEST(mips_hpt_frequency, HZ); write_c0_count(0); timer_ack(); -- GitLab From 3d4656d68bad84604f5b01f93e066cd02f77154b Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Fri, 31 Jul 2009 14:52:51 +0200 Subject: [PATCH 0742/1342] MIPS: Jazz: Fix read buffer overflow Check whether index is within bounds before testing the element. Signed-off-by: Roel Kluin Signed-off-by: Ralf Baechle --- arch/mips/jazz/jazzdma.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/mips/jazz/jazzdma.c b/arch/mips/jazz/jazzdma.c index f0fd636723b..0d64d0f4641 100644 --- a/arch/mips/jazz/jazzdma.c +++ b/arch/mips/jazz/jazzdma.c @@ -190,7 +190,7 @@ int vdma_free(unsigned long laddr) return -1; } - while (pgtbl[i].owner == laddr && i < VDMA_PGTBL_ENTRIES) { + while (i < VDMA_PGTBL_ENTRIES && pgtbl[i].owner == laddr) { pgtbl[i].owner = VDMA_PAGE_EMPTY; i++; } -- GitLab From 39b3d44624e9c54e7406274beaf569fe33af2b96 Mon Sep 17 00:00:00 2001 From: David Daney Date: Fri, 31 Jul 2009 14:30:07 -0700 Subject: [PATCH 0743/1342] MIPS: Octeon: Run IPI code with interrupts disabled. In mm/slab.c the function do_ccupdate_local requires that interrupts be disabled. If they are not, we panic with CONFIG_DEBUG_SLAB. So we disable interrupts while processing IPIs. Also these are not shared irqs, so get rid of the IRQF_SHARED flag. Signed-off-by: David Daney Signed-off-by: Ralf Baechle --- arch/mips/cavium-octeon/smp.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/mips/cavium-octeon/smp.c b/arch/mips/cavium-octeon/smp.c index 0b891a9c625..32d51a31dc4 100644 --- a/arch/mips/cavium-octeon/smp.c +++ b/arch/mips/cavium-octeon/smp.c @@ -194,11 +194,11 @@ static void octeon_init_secondary(void) void octeon_prepare_cpus(unsigned int max_cpus) { cvmx_write_csr(CVMX_CIU_MBOX_CLRX(cvmx_get_core_num()), 0xffffffff); - if (request_irq(OCTEON_IRQ_MBOX0, mailbox_interrupt, IRQF_SHARED, + if (request_irq(OCTEON_IRQ_MBOX0, mailbox_interrupt, IRQF_DISABLED, "mailbox0", mailbox_interrupt)) { panic("Cannot request_irq(OCTEON_IRQ_MBOX0)\n"); } - if (request_irq(OCTEON_IRQ_MBOX1, mailbox_interrupt, IRQF_SHARED, + if (request_irq(OCTEON_IRQ_MBOX1, mailbox_interrupt, IRQF_DISABLED, "mailbox1", mailbox_interrupt)) { panic("Cannot request_irq(OCTEON_IRQ_MBOX1)\n"); } -- GitLab From 6f9fdeb6761a46ded6bf4b799993a3f235ab853d Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Mon, 3 Aug 2009 10:50:19 +0100 Subject: [PATCH 0744/1342] MIPS: Module: Make error messages unique. There were three different errors resulting in a "dangerous relocation" message. Add the relocation type to the messgages to make them more useful. Signed-off-by: Ralf Baechle --- arch/mips/kernel/module.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) diff --git a/arch/mips/kernel/module.c b/arch/mips/kernel/module.c index e465851a616..6f51dda87fc 100644 --- a/arch/mips/kernel/module.c +++ b/arch/mips/kernel/module.c @@ -98,7 +98,8 @@ static int apply_r_mips_32_rela(struct module *me, u32 *location, Elf_Addr v) static int apply_r_mips_26_rel(struct module *me, u32 *location, Elf_Addr v) { if (v % 4) { - printk(KERN_ERR "module %s: dangerous relocation\n", me->name); + pr_err("module %s: dangerous R_MIPS_26 REL relocation\n", + me->name); return -ENOEXEC; } @@ -118,7 +119,8 @@ static int apply_r_mips_26_rel(struct module *me, u32 *location, Elf_Addr v) static int apply_r_mips_26_rela(struct module *me, u32 *location, Elf_Addr v) { if (v % 4) { - printk(KERN_ERR "module %s: dangerous relocation\n", me->name); + pr_err("module %s: dangerous R_MIPS_26 RELArelocation\n", + me->name); return -ENOEXEC; } @@ -222,7 +224,7 @@ static int apply_r_mips_lo16_rel(struct module *me, u32 *location, Elf_Addr v) return 0; out_danger: - printk(KERN_ERR "module %s: dangerous " "relocation\n", me->name); + pr_err("module %s: dangerous R_MIPS_LO16 REL relocation\n", me->name); return -ENOEXEC; } -- GitLab From e2a9cf96a0af24f33206b4bb98cc3a12242260c1 Mon Sep 17 00:00:00 2001 From: Raghu Gandham Date: Fri, 10 Jul 2009 02:01:32 -0700 Subject: [PATCH 0745/1342] MIPS: VPE: Fix compiler warning. Signed-off-by: Raghu Gandham Signed-off-by: Ralf Baechle --- arch/mips/kernel/vpe.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/arch/mips/kernel/vpe.c b/arch/mips/kernel/vpe.c index 07b9ec2c6e3..3d4ef841d82 100644 --- a/arch/mips/kernel/vpe.c +++ b/arch/mips/kernel/vpe.c @@ -327,7 +327,8 @@ static void layout_sections(struct module *mod, const Elf_Ehdr * hdr, || (s->sh_flags & masks[m][1]) || s->sh_entsize != ~0UL) continue; - s->sh_entsize = get_offset(&mod->core_size, s); + s->sh_entsize = + get_offset((unsigned long *)&mod->core_size, s); } if (m == 0) -- GitLab From 477c4b07406357ad93d0e32788dbf3ee814eadaa Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Mon, 3 Aug 2009 12:26:40 +0100 Subject: [PATCH 0746/1342] MIPS: VPE: Free relocation chain on error. This may happen if a bad sequence of relocations is being encountered. Signed-off-by: Ralf Baechle --- arch/mips/kernel/vpe.c | 15 ++++++++++++--- 1 file changed, 12 insertions(+), 3 deletions(-) diff --git a/arch/mips/kernel/vpe.c b/arch/mips/kernel/vpe.c index 3d4ef841d82..245b03e8808 100644 --- a/arch/mips/kernel/vpe.c +++ b/arch/mips/kernel/vpe.c @@ -462,16 +462,15 @@ static int apply_r_mips_lo16(struct module *me, uint32_t *location, { unsigned long insnlo = *location; Elf32_Addr val, vallo; + struct mips_hi16 *l, *next; /* Sign extend the addend we extract from the lo insn. */ vallo = ((insnlo & 0xffff) ^ 0x8000) - 0x8000; if (mips_hi16_list != NULL) { - struct mips_hi16 *l; l = mips_hi16_list; while (l != NULL) { - struct mips_hi16 *next; unsigned long insn; /* @@ -481,7 +480,7 @@ static int apply_r_mips_lo16(struct module *me, uint32_t *location, printk(KERN_DEBUG "VPE loader: " "apply_r_mips_lo16/hi16: \t" "inconsistent value information\n"); - return -ENOEXEC; + goto out_free; } /* @@ -519,6 +518,16 @@ static int apply_r_mips_lo16(struct module *me, uint32_t *location, *location = insnlo; return 0; + +out_free: + while (l != NULL) { + next = l->next; + kfree(l); + l = next; + } + mips_hi16_list = NULL; + + return -ENOEXEC; } static int (*reloc_handlers[]) (struct module *me, uint32_t *location, -- GitLab From f18b51cc1f97ca290256e8f94127f6856a42d605 Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Mon, 3 Aug 2009 12:54:35 +0100 Subject: [PATCH 0747/1342] MIPS: VPE: Make various functions static. None of these is used outside the VPE loader. Signed-off-by: Ralf Baechle --- arch/mips/kernel/vpe.c | 17 ++++++++--------- 1 file changed, 8 insertions(+), 9 deletions(-) diff --git a/arch/mips/kernel/vpe.c b/arch/mips/kernel/vpe.c index 245b03e8808..6cbeb2a5452 100644 --- a/arch/mips/kernel/vpe.c +++ b/arch/mips/kernel/vpe.c @@ -155,10 +155,9 @@ struct { }; static void release_progmem(void *ptr); -extern void save_gp_address(unsigned int secbase, unsigned int rel); /* get the vpe associated with this minor */ -struct vpe *get_vpe(int minor) +static struct vpe *get_vpe(int minor) { struct vpe *v; @@ -174,7 +173,7 @@ struct vpe *get_vpe(int minor) } /* get the vpe associated with this minor */ -struct tc *get_tc(int index) +static struct tc *get_tc(int index) { struct tc *t; @@ -199,7 +198,7 @@ struct tc *get_tc_unused(void) } /* allocate a vpe and associate it with this minor (or index) */ -struct vpe *alloc_vpe(int minor) +static struct vpe *alloc_vpe(int minor) { struct vpe *v; @@ -216,7 +215,7 @@ struct vpe *alloc_vpe(int minor) } /* allocate a tc. At startup only tc0 is running, all other can be halted. */ -struct tc *alloc_tc(int index) +static struct tc *alloc_tc(int index) { struct tc *tc; @@ -232,7 +231,7 @@ out: } /* clean up and free everything */ -void release_vpe(struct vpe *v) +static void release_vpe(struct vpe *v) { list_del(&v->list); if (v->load_addr) @@ -240,7 +239,7 @@ void release_vpe(struct vpe *v) kfree(v); } -void dump_mtregs(void) +static void dump_mtregs(void) { unsigned long val; @@ -551,7 +550,7 @@ static char *rstrs[] = { [R_MIPS_PC16] = "MIPS_PC16" }; -int apply_relocations(Elf32_Shdr *sechdrs, +static int apply_relocations(Elf32_Shdr *sechdrs, const char *strtab, unsigned int symindex, unsigned int relsec, @@ -596,7 +595,7 @@ int apply_relocations(Elf32_Shdr *sechdrs, return 0; } -void save_gp_address(unsigned int secbase, unsigned int rel) +static inline void save_gp_address(unsigned int secbase, unsigned int rel) { gp_addr = secbase + rel; gp_offs = gp_addr - (secbase & 0xffff0000); -- GitLab From 349c4229ed305146a558008d393c622d715cd11d Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Mon, 3 Aug 2009 12:56:39 +0100 Subject: [PATCH 0748/1342] MIPS: VPE: Fix bogus indentation. Signed-off-by: Ralf Baechle --- arch/mips/kernel/vpe.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/mips/kernel/vpe.c b/arch/mips/kernel/vpe.c index 6cbeb2a5452..e3687524fdb 100644 --- a/arch/mips/kernel/vpe.c +++ b/arch/mips/kernel/vpe.c @@ -73,7 +73,7 @@ static int major; static const int minor = 1; /* fixed for now */ #ifdef CONFIG_MIPS_APSP_KSPD - static struct kspd_notifications kspd_events; +static struct kspd_notifications kspd_events; static int kspd_events_reqd = 0; #endif -- GitLab From ce21f4e86f89d352efecd044958db1917033b49b Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Mon, 3 Aug 2009 12:57:52 +0100 Subject: [PATCH 0749/1342] MIPS: VPE: Delete unused function get_tc_unused(). Signed-off-by: Ralf Baechle --- arch/mips/kernel/vpe.c | 12 ------------ 1 file changed, 12 deletions(-) diff --git a/arch/mips/kernel/vpe.c b/arch/mips/kernel/vpe.c index e3687524fdb..9a1ab7e87fd 100644 --- a/arch/mips/kernel/vpe.c +++ b/arch/mips/kernel/vpe.c @@ -185,18 +185,6 @@ static struct tc *get_tc(int index) return NULL; } -struct tc *get_tc_unused(void) -{ - struct tc *t; - - list_for_each_entry(t, &vpecontrol.tc_list, list) { - if (t->state == TC_STATE_UNUSED) - return t; - } - - return NULL; -} - /* allocate a vpe and associate it with this minor (or index) */ static struct vpe *alloc_vpe(int minor) { -- GitLab From 54822de7793bf9aa56d79cc173281cdb23b37f9f Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Mon, 3 Aug 2009 17:27:19 +0100 Subject: [PATCH 0750/1342] MIPS: Wire up accept4 syscall. Signed-off-by: Ralf Baechle --- arch/mips/include/asm/unistd.h | 15 +++++++++------ arch/mips/kernel/scall32-o32.S | 1 + arch/mips/kernel/scall64-64.S | 1 + arch/mips/kernel/scall64-n32.S | 1 + arch/mips/kernel/scall64-o32.S | 1 + 5 files changed, 13 insertions(+), 6 deletions(-) diff --git a/arch/mips/include/asm/unistd.h b/arch/mips/include/asm/unistd.h index b70c49fdda2..e753a777949 100644 --- a/arch/mips/include/asm/unistd.h +++ b/arch/mips/include/asm/unistd.h @@ -354,16 +354,17 @@ #define __NR_pwritev (__NR_Linux + 331) #define __NR_rt_tgsigqueueinfo (__NR_Linux + 332) #define __NR_perf_counter_open (__NR_Linux + 333) +#define __NR_accept4 (__NR_Linux + 334) /* * Offset of the last Linux o32 flavoured syscall */ -#define __NR_Linux_syscalls 333 +#define __NR_Linux_syscalls 334 #endif /* _MIPS_SIM == _MIPS_SIM_ABI32 */ #define __NR_O32_Linux 4000 -#define __NR_O32_Linux_syscalls 333 +#define __NR_O32_Linux_syscalls 334 #if _MIPS_SIM == _MIPS_SIM_ABI64 @@ -664,16 +665,17 @@ #define __NR_pwritev (__NR_Linux + 290) #define __NR_rt_tgsigqueueinfo (__NR_Linux + 291) #define __NR_perf_counter_open (__NR_Linux + 292) +#define __NR_accept4 (__NR_Linux + 293) /* * Offset of the last Linux 64-bit flavoured syscall */ -#define __NR_Linux_syscalls 292 +#define __NR_Linux_syscalls 293 #endif /* _MIPS_SIM == _MIPS_SIM_ABI64 */ #define __NR_64_Linux 5000 -#define __NR_64_Linux_syscalls 292 +#define __NR_64_Linux_syscalls 293 #if _MIPS_SIM == _MIPS_SIM_NABI32 @@ -978,16 +980,17 @@ #define __NR_pwritev (__NR_Linux + 294) #define __NR_rt_tgsigqueueinfo (__NR_Linux + 295) #define __NR_perf_counter_open (__NR_Linux + 296) +#define __NR_accept4 (__NR_Linux + 297) /* * Offset of the last N32 flavoured syscall */ -#define __NR_Linux_syscalls 296 +#define __NR_Linux_syscalls 297 #endif /* _MIPS_SIM == _MIPS_SIM_NABI32 */ #define __NR_N32_Linux 6000 -#define __NR_N32_Linux_syscalls 296 +#define __NR_N32_Linux_syscalls 297 #ifdef __KERNEL__ diff --git a/arch/mips/kernel/scall32-o32.S b/arch/mips/kernel/scall32-o32.S index 20a86e08fd5..b5708212353 100644 --- a/arch/mips/kernel/scall32-o32.S +++ b/arch/mips/kernel/scall32-o32.S @@ -654,6 +654,7 @@ einval: li v0, -ENOSYS sys sys_pwritev 6 sys sys_rt_tgsigqueueinfo 4 sys sys_perf_counter_open 5 + sys sys_accept4 4 .endm /* We pre-compute the number of _instruction_ bytes needed to diff --git a/arch/mips/kernel/scall64-64.S b/arch/mips/kernel/scall64-64.S index b046130d4c5..3d866f24e06 100644 --- a/arch/mips/kernel/scall64-64.S +++ b/arch/mips/kernel/scall64-64.S @@ -491,4 +491,5 @@ sys_call_table: PTR sys_pwritev /* 5390 */ PTR sys_rt_tgsigqueueinfo PTR sys_perf_counter_open + PTR sys_accept4 .size sys_call_table,.-sys_call_table diff --git a/arch/mips/kernel/scall64-n32.S b/arch/mips/kernel/scall64-n32.S index 15874f9812c..e855b118a07 100644 --- a/arch/mips/kernel/scall64-n32.S +++ b/arch/mips/kernel/scall64-n32.S @@ -417,4 +417,5 @@ EXPORT(sysn32_call_table) PTR sys_pwritev PTR compat_sys_rt_tgsigqueueinfo /* 5295 */ PTR sys_perf_counter_open + PTR sys_accept4 .size sysn32_call_table,.-sysn32_call_table diff --git a/arch/mips/kernel/scall64-o32.S b/arch/mips/kernel/scall64-o32.S index 781e0f1e953..0c49f1a660b 100644 --- a/arch/mips/kernel/scall64-o32.S +++ b/arch/mips/kernel/scall64-o32.S @@ -537,4 +537,5 @@ sys_call_table: PTR compat_sys_pwritev PTR compat_sys_rt_tgsigqueueinfo PTR sys_perf_counter_open + PTR sys_accept4 .size sys_call_table,.-sys_call_table -- GitLab From 8523acfe40efc1a8d3da8f473ca67cb195b06f0c Mon Sep 17 00:00:00 2001 From: Thomas Hellstrom Date: Mon, 3 Aug 2009 09:25:45 +0200 Subject: [PATCH 0751/1342] x86: Fix CPA memtype reserving in the set_pages_array*() cases The code was incorrectly reserving memtypes using the page virtual address instead of the physical address. Furthermore, the code was not ignoring highmem pages as it ought to. ( upstream does not pass in highmem pages yet - but upcoming graphics code will do it and there's no reason to not handle this properly in the CPA APIs.) Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=13884 Signed-off-by: Thomas Hellstrom Acked-by: Suresh Siddha Cc: Cc: dri-devel@lists.sourceforge.net Cc: venkatesh.pallipadi@intel.com LKML-Reference: <1249284345-7654-1-git-send-email-thellstrom@vmware.com> Signed-off-by: Ingo Molnar --- arch/x86/mm/pageattr.c | 30 +++++++++++++++++++++--------- 1 file changed, 21 insertions(+), 9 deletions(-) diff --git a/arch/x86/mm/pageattr.c b/arch/x86/mm/pageattr.c index 895d90e1a81..7e600c1962d 100644 --- a/arch/x86/mm/pageattr.c +++ b/arch/x86/mm/pageattr.c @@ -591,9 +591,12 @@ static int __change_page_attr(struct cpa_data *cpa, int primary) unsigned int level; pte_t *kpte, old_pte; - if (cpa->flags & CPA_PAGES_ARRAY) - address = (unsigned long)page_address(cpa->pages[cpa->curpage]); - else if (cpa->flags & CPA_ARRAY) + if (cpa->flags & CPA_PAGES_ARRAY) { + struct page *page = cpa->pages[cpa->curpage]; + if (unlikely(PageHighMem(page))) + return 0; + address = (unsigned long)page_address(page); + } else if (cpa->flags & CPA_ARRAY) address = cpa->vaddr[cpa->curpage]; else address = *cpa->vaddr; @@ -697,9 +700,12 @@ static int cpa_process_alias(struct cpa_data *cpa) * No need to redo, when the primary call touched the direct * mapping already: */ - if (cpa->flags & CPA_PAGES_ARRAY) - vaddr = (unsigned long)page_address(cpa->pages[cpa->curpage]); - else if (cpa->flags & CPA_ARRAY) + if (cpa->flags & CPA_PAGES_ARRAY) { + struct page *page = cpa->pages[cpa->curpage]; + if (unlikely(PageHighMem(page))) + return 0; + vaddr = (unsigned long)page_address(page); + } else if (cpa->flags & CPA_ARRAY) vaddr = cpa->vaddr[cpa->curpage]; else vaddr = *cpa->vaddr; @@ -1122,7 +1128,9 @@ int set_pages_array_uc(struct page **pages, int addrinarray) int free_idx; for (i = 0; i < addrinarray; i++) { - start = (unsigned long)page_address(pages[i]); + if (PageHighMem(pages[i])) + continue; + start = page_to_pfn(pages[i]) << PAGE_SHIFT; end = start + PAGE_SIZE; if (reserve_memtype(start, end, _PAGE_CACHE_UC_MINUS, NULL)) goto err_out; @@ -1135,7 +1143,9 @@ int set_pages_array_uc(struct page **pages, int addrinarray) err_out: free_idx = i; for (i = 0; i < free_idx; i++) { - start = (unsigned long)page_address(pages[i]); + if (PageHighMem(pages[i])) + continue; + start = page_to_pfn(pages[i]) << PAGE_SHIFT; end = start + PAGE_SIZE; free_memtype(start, end); } @@ -1164,7 +1174,9 @@ int set_pages_array_wb(struct page **pages, int addrinarray) return retval; for (i = 0; i < addrinarray; i++) { - start = (unsigned long)page_address(pages[i]); + if (PageHighMem(pages[i])) + continue; + start = page_to_pfn(pages[i]) << PAGE_SHIFT; end = start + PAGE_SIZE; free_memtype(start, end); } -- GitLab From af0d3b103bcfa877343ee338de12002cd50c9ee5 Mon Sep 17 00:00:00 2001 From: Dave Young Date: Mon, 3 Aug 2009 04:26:16 +0000 Subject: [PATCH 0752/1342] bluetooth: rfcomm_init bug fix rfcomm tty may be used before rfcomm_tty_driver initilized, The problem is that now socket layer init before tty layer, if userspace program do socket callback right here then oops will happen. reporting in: http://marc.info/?l=linux-bluetooth&m=124404919324542&w=2 make 3 changes: 1. remove #ifdef in rfcomm/core.c, make it blank function when rfcomm tty not selected in rfcomm.h 2. tune the rfcomm_init error patch to ensure tty driver initilized before rfcomm socket usage. 3. remove __exit for rfcomm_cleanup_sockets because above change need call it in a __init function. Reported-by: Oliver Hartkopp Tested-by: Oliver Hartkopp Signed-off-by: Dave Young Signed-off-by: David S. Miller --- include/net/bluetooth/rfcomm.h | 12 +++++++++++- net/bluetooth/rfcomm/core.c | 27 +++++++++++++++++++-------- net/bluetooth/rfcomm/sock.c | 2 +- 3 files changed, 31 insertions(+), 10 deletions(-) diff --git a/include/net/bluetooth/rfcomm.h b/include/net/bluetooth/rfcomm.h index 80072611d26..c274993234e 100644 --- a/include/net/bluetooth/rfcomm.h +++ b/include/net/bluetooth/rfcomm.h @@ -355,7 +355,17 @@ struct rfcomm_dev_list_req { }; int rfcomm_dev_ioctl(struct sock *sk, unsigned int cmd, void __user *arg); + +#ifdef CONFIG_BT_RFCOMM_TTY int rfcomm_init_ttys(void); void rfcomm_cleanup_ttys(void); - +#else +static inline int rfcomm_init_ttys(void) +{ + return 0; +} +static inline void rfcomm_cleanup_ttys(void) +{ +} +#endif #endif /* __RFCOMM_H */ diff --git a/net/bluetooth/rfcomm/core.c b/net/bluetooth/rfcomm/core.c index e50566ebf9f..94b3388c188 100644 --- a/net/bluetooth/rfcomm/core.c +++ b/net/bluetooth/rfcomm/core.c @@ -2080,28 +2080,41 @@ static CLASS_ATTR(rfcomm_dlc, S_IRUGO, rfcomm_dlc_sysfs_show, NULL); /* ---- Initialization ---- */ static int __init rfcomm_init(void) { + int ret; + l2cap_load(); hci_register_cb(&rfcomm_cb); rfcomm_thread = kthread_run(rfcomm_run, NULL, "krfcommd"); if (IS_ERR(rfcomm_thread)) { - hci_unregister_cb(&rfcomm_cb); - return PTR_ERR(rfcomm_thread); + ret = PTR_ERR(rfcomm_thread); + goto out_thread; } if (class_create_file(bt_class, &class_attr_rfcomm_dlc) < 0) BT_ERR("Failed to create RFCOMM info file"); - rfcomm_init_sockets(); + ret = rfcomm_init_ttys(); + if (ret) + goto out_tty; -#ifdef CONFIG_BT_RFCOMM_TTY - rfcomm_init_ttys(); -#endif + ret = rfcomm_init_sockets(); + if (ret) + goto out_sock; BT_INFO("RFCOMM ver %s", VERSION); return 0; + +out_sock: + rfcomm_cleanup_ttys(); +out_tty: + kthread_stop(rfcomm_thread); +out_thread: + hci_unregister_cb(&rfcomm_cb); + + return ret; } static void __exit rfcomm_exit(void) @@ -2112,9 +2125,7 @@ static void __exit rfcomm_exit(void) kthread_stop(rfcomm_thread); -#ifdef CONFIG_BT_RFCOMM_TTY rfcomm_cleanup_ttys(); -#endif rfcomm_cleanup_sockets(); } diff --git a/net/bluetooth/rfcomm/sock.c b/net/bluetooth/rfcomm/sock.c index 7f482784e9f..0b85e811685 100644 --- a/net/bluetooth/rfcomm/sock.c +++ b/net/bluetooth/rfcomm/sock.c @@ -1132,7 +1132,7 @@ error: return err; } -void __exit rfcomm_cleanup_sockets(void) +void rfcomm_cleanup_sockets(void) { class_remove_file(bt_class, &class_attr_rfcomm); -- GitLab From 202ff1ec8e53d5dd36e1a5bd4b0a7ed7dbd45087 Mon Sep 17 00:00:00 2001 From: Mallikarjuna R Chilakala Date: Mon, 3 Aug 2009 07:20:38 +0000 Subject: [PATCH 0753/1342] ixgbe: Patch to modify 82598 PCIe completion timeout values The default completion timeout values for 82598 should be in the range of 50us to 50ms, however the hardware default for these parts is 500us to 1ms which is less than the 10ms recommended by the pcie spec. To address this we need to increase the value to either 10ms to 250ms for capability version 1 configuration, or 16ms to 55ms for version 2. Signed-off-by: Mallikarjuna R Chilakala Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_82598.c | 67 ++++++++++++++++++++++++++++++++- drivers/net/ixgbe/ixgbe_type.h | 8 ++++ 2 files changed, 74 insertions(+), 1 deletion(-) diff --git a/drivers/net/ixgbe/ixgbe_82598.c b/drivers/net/ixgbe/ixgbe_82598.c index b9923047ce1..522c03bc1da 100644 --- a/drivers/net/ixgbe/ixgbe_82598.c +++ b/drivers/net/ixgbe/ixgbe_82598.c @@ -49,6 +49,51 @@ static s32 ixgbe_setup_copper_link_speed_82598(struct ixgbe_hw *hw, static s32 ixgbe_read_i2c_eeprom_82598(struct ixgbe_hw *hw, u8 byte_offset, u8 *eeprom_data); +/** + * ixgbe_set_pcie_completion_timeout - set pci-e completion timeout + * @hw: pointer to the HW structure + * + * The defaults for 82598 should be in the range of 50us to 50ms, + * however the hardware default for these parts is 500us to 1ms which is less + * than the 10ms recommended by the pci-e spec. To address this we need to + * increase the value to either 10ms to 250ms for capability version 1 config, + * or 16ms to 55ms for version 2. + **/ +void ixgbe_set_pcie_completion_timeout(struct ixgbe_hw *hw) +{ + struct ixgbe_adapter *adapter = hw->back; + u32 gcr = IXGBE_READ_REG(hw, IXGBE_GCR); + u16 pcie_devctl2; + + /* only take action if timeout value is defaulted to 0 */ + if (gcr & IXGBE_GCR_CMPL_TMOUT_MASK) + goto out; + + /* + * if capababilities version is type 1 we can write the + * timeout of 10ms to 250ms through the GCR register + */ + if (!(gcr & IXGBE_GCR_CAP_VER2)) { + gcr |= IXGBE_GCR_CMPL_TMOUT_10ms; + goto out; + } + + /* + * for version 2 capabilities we need to write the config space + * directly in order to set the completion timeout value for + * 16ms to 55ms + */ + pci_read_config_word(adapter->pdev, + IXGBE_PCI_DEVICE_CONTROL2, &pcie_devctl2); + pcie_devctl2 |= IXGBE_PCI_DEVICE_CONTROL2_16ms; + pci_write_config_word(adapter->pdev, + IXGBE_PCI_DEVICE_CONTROL2, pcie_devctl2); +out: + /* disable completion timeout resend */ + gcr &= ~IXGBE_GCR_CMPL_TMOUT_RESEND; + IXGBE_WRITE_REG(hw, IXGBE_GCR, gcr); +} + /** * ixgbe_get_pcie_msix_count_82598 - Gets MSI-X vector count * @hw: pointer to hardware structure @@ -152,6 +197,26 @@ out: return ret_val; } +/** + * ixgbe_start_hw_82598 - Prepare hardware for Tx/Rx + * @hw: pointer to hardware structure + * + * Starts the hardware using the generic start_hw function. + * Then set pcie completion timeout + **/ +s32 ixgbe_start_hw_82598(struct ixgbe_hw *hw) +{ + s32 ret_val = 0; + + ret_val = ixgbe_start_hw_generic(hw); + + /* set the completion timeout for interface */ + if (ret_val == 0) + ixgbe_set_pcie_completion_timeout(hw); + + return ret_val; +} + /** * ixgbe_get_link_capabilities_82598 - Determines link capabilities * @hw: pointer to hardware structure @@ -1085,7 +1150,7 @@ out: static struct ixgbe_mac_operations mac_ops_82598 = { .init_hw = &ixgbe_init_hw_generic, .reset_hw = &ixgbe_reset_hw_82598, - .start_hw = &ixgbe_start_hw_generic, + .start_hw = &ixgbe_start_hw_82598, .clear_hw_cntrs = &ixgbe_clear_hw_cntrs_generic, .get_media_type = &ixgbe_get_media_type_82598, .get_supported_physical_layer = &ixgbe_get_supported_physical_layer_82598, diff --git a/drivers/net/ixgbe/ixgbe_type.h b/drivers/net/ixgbe/ixgbe_type.h index fa87309dc08..be90eb4575f 100644 --- a/drivers/net/ixgbe/ixgbe_type.h +++ b/drivers/net/ixgbe/ixgbe_type.h @@ -718,6 +718,12 @@ #define IXGBE_ECC_STATUS_82599 0x110E0 #define IXGBE_BAR_CTRL_82599 0x110F4 +/* PCI Express Control */ +#define IXGBE_GCR_CMPL_TMOUT_MASK 0x0000F000 +#define IXGBE_GCR_CMPL_TMOUT_10ms 0x00001000 +#define IXGBE_GCR_CMPL_TMOUT_RESEND 0x00010000 +#define IXGBE_GCR_CAP_VER2 0x00040000 + /* Time Sync Registers */ #define IXGBE_TSYNCRXCTL 0x05188 /* Rx Time Sync Control register - RW */ #define IXGBE_TSYNCTXCTL 0x08C00 /* Tx Time Sync Control register - RW */ @@ -1521,6 +1527,7 @@ /* PCI Bus Info */ #define IXGBE_PCI_LINK_STATUS 0xB2 +#define IXGBE_PCI_DEVICE_CONTROL2 0xC8 #define IXGBE_PCI_LINK_WIDTH 0x3F0 #define IXGBE_PCI_LINK_WIDTH_1 0x10 #define IXGBE_PCI_LINK_WIDTH_2 0x20 @@ -1531,6 +1538,7 @@ #define IXGBE_PCI_LINK_SPEED_5000 0x2 #define IXGBE_PCI_HEADER_TYPE_REGISTER 0x0E #define IXGBE_PCI_HEADER_TYPE_MULTIFUNC 0x80 +#define IXGBE_PCI_DEVICE_CONTROL2_16ms 0x0005 /* Number of 100 microseconds we wait for PCI Express master disable */ #define IXGBE_PCI_MASTER_DISABLE_TIMEOUT 800 -- GitLab From cd3468bad96c00b5a512f551674f36776129520e Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Wed, 29 Jul 2009 22:07:44 +0200 Subject: [PATCH 0754/1342] cfg80211: add two missing NULL pointer checks These pointers can be NULL, the is_mesh() case isn't ever hit in the current kernel, but cmp_ies() can be hit under certain conditions. Signed-off-by: Johannes Berg Cc: stable@kernel.org [2.6.29, 2.6.30] Signed-off-by: John W. Linville --- net/wireless/scan.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/net/wireless/scan.c b/net/wireless/scan.c index 9271118e1fc..7e595ce24ee 100644 --- a/net/wireless/scan.c +++ b/net/wireless/scan.c @@ -118,7 +118,7 @@ static int cmp_ies(u8 num, u8 *ies1, size_t len1, u8 *ies2, size_t len2) if (!ie1 && !ie2) return 0; - if (!ie1) + if (!ie1 || !ie2) return -1; r = memcmp(ie1 + 2, ie2 + 2, min(ie1[1], ie2[1])); @@ -171,6 +171,8 @@ static bool is_mesh(struct cfg80211_bss *a, ie = find_ie(WLAN_EID_MESH_CONFIG, a->information_elements, a->len_information_elements); + if (!ie) + return false; if (ie[1] != IEEE80211_MESH_CONFIG_LEN) return false; -- GitLab From 371842448c05b42d11a4be1c8e4e81d62ecc7534 Mon Sep 17 00:00:00 2001 From: "Luis R. Rodriguez" Date: Thu, 30 Jul 2009 17:43:48 -0700 Subject: [PATCH 0755/1342] cfg80211: fix regression on beacon world roaming feature A regression was added through patch a4ed90d6: "cfg80211: respect API on orig_flags on channel for beacon hint" We did indeed respect _orig flags but the intention was not clearly stated in the commit log. This patch fixes firmware issues picked up by iwlwifi when we lift passive scan of beaconing restrictions on channels its EEPROM has been configured to always enable. By doing so though we also disallowed beacon hints on devices registering their wiphy with custom world regulatory domains enabled, this happens to be currently ath5k, ath9k and ar9170. The passive scan and beacon restrictions on those devices would never be lifted even if we did find a beacon and the hardware did support such enhancements when world roaming. Since Johannes indicates iwlwifi firmware cannot be changed to allow beacon hinting we set up a flag now to specifically allow drivers to disable beacon hints for devices which cannot use them. We enable the flag on iwlwifi to disable beacon hints and by default enable it for all other drivers. It should be noted beacon hints lift passive scan flags and beacon restrictions when we receive a beacon from an AP on any 5 GHz non-DFS channels, and channels 12-14 on the 2.4 GHz band. We don't bother with channels 1-11 as those channels are allowed world wide. This should fix world roaming for ath5k, ath9k and ar9170, thereby improving scan time when we receive the first beacon from any AP, and also enabling beaconing operation (AP/IBSS/Mesh) on cards which would otherwise not be allowed to do so. Drivers not using custom regulatory stuff (wiphy_apply_custom_regulatory()) were not affected by this as the orig_flags for the channels would have been cleared upon wiphy registration. I tested this with a world roaming ath5k card. Cc: Jouni Malinen Signed-off-by: Luis R. Rodriguez Reviewed-by: Johannes Berg Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-core.c | 3 +++ drivers/net/wireless/iwlwifi/iwl3945-base.c | 3 +++ include/net/cfg80211.h | 5 +++++ net/wireless/reg.c | 9 +++++---- net/wireless/reg.h | 3 ++- 5 files changed, 18 insertions(+), 5 deletions(-) diff --git a/drivers/net/wireless/iwlwifi/iwl-core.c b/drivers/net/wireless/iwlwifi/iwl-core.c index 6ab07165ea2..18b135f510e 100644 --- a/drivers/net/wireless/iwlwifi/iwl-core.c +++ b/drivers/net/wireless/iwlwifi/iwl-core.c @@ -1332,6 +1332,9 @@ int iwl_setup_mac(struct iwl_priv *priv) hw->wiphy->custom_regulatory = true; + /* Firmware does not support this */ + hw->wiphy->disable_beacon_hints = true; + hw->wiphy->max_scan_ssids = PROBE_OPTION_MAX; /* we create the 802.11 header and a zero-length SSID element */ hw->wiphy->max_scan_ie_len = IWL_MAX_PROBE_REQUEST - 24 - 2; diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c index 2f50ab60bfd..523843369ca 100644 --- a/drivers/net/wireless/iwlwifi/iwl3945-base.c +++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c @@ -3968,6 +3968,9 @@ static int iwl3945_setup_mac(struct iwl_priv *priv) hw->wiphy->custom_regulatory = true; + /* Firmware does not support this */ + hw->wiphy->disable_beacon_hints = true; + hw->wiphy->max_scan_ssids = PROBE_OPTION_MAX_3945; /* we create the 802.11 header and a zero-length SSID element */ hw->wiphy->max_scan_ie_len = IWL_MAX_PROBE_REQUEST - 24 - 2; diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index 1a21895b732..d1892d66701 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -979,6 +979,10 @@ struct cfg80211_ops { * channels at a later time. This can be used for devices which do not * have calibration information gauranteed for frequencies or settings * outside of its regulatory domain. + * @disable_beacon_hints: enable this if your driver needs to ensure that + * passive scan flags and beaconing flags may not be lifted by cfg80211 + * due to regulatory beacon hints. For more information on beacon + * hints read the documenation for regulatory_hint_found_beacon() * @reg_notifier: the driver's regulatory notification callback * @regd: the driver's regulatory domain, if one was requested via * the regulatory_hint() API. This can be used by the driver @@ -1004,6 +1008,7 @@ struct wiphy { bool custom_regulatory; bool strict_regulatory; + bool disable_beacon_hints; enum cfg80211_signal_type signal_type; diff --git a/net/wireless/reg.c b/net/wireless/reg.c index 5e14371cda7..75a406d3361 100644 --- a/net/wireless/reg.c +++ b/net/wireless/reg.c @@ -1089,17 +1089,18 @@ static void handle_reg_beacon(struct wiphy *wiphy, chan->beacon_found = true; + if (wiphy->disable_beacon_hints) + return; + chan_before.center_freq = chan->center_freq; chan_before.flags = chan->flags; - if ((chan->flags & IEEE80211_CHAN_PASSIVE_SCAN) && - !(chan->orig_flags & IEEE80211_CHAN_PASSIVE_SCAN)) { + if (chan->flags & IEEE80211_CHAN_PASSIVE_SCAN) { chan->flags &= ~IEEE80211_CHAN_PASSIVE_SCAN; channel_changed = true; } - if ((chan->flags & IEEE80211_CHAN_NO_IBSS) && - !(chan->orig_flags & IEEE80211_CHAN_NO_IBSS)) { + if (chan->flags & IEEE80211_CHAN_NO_IBSS) { chan->flags &= ~IEEE80211_CHAN_NO_IBSS; channel_changed = true; } diff --git a/net/wireless/reg.h b/net/wireless/reg.h index e37829a49dc..4e167a8e11b 100644 --- a/net/wireless/reg.h +++ b/net/wireless/reg.h @@ -30,7 +30,8 @@ int set_regdom(const struct ieee80211_regdomain *rd); * non-radar 5 GHz channels. * * Drivers do not need to call this, cfg80211 will do it for after a scan - * on a newly found BSS. + * on a newly found BSS. If you cannot make use of this feature you can + * set the wiphy->disable_beacon_hints to true. */ int regulatory_hint_found_beacon(struct wiphy *wiphy, struct ieee80211_channel *beacon_chan, -- GitLab From dbc1eec485625228895ded6baf6bd01ce2475410 Mon Sep 17 00:00:00 2001 From: Patrick Simmons Date: Sun, 2 Aug 2009 02:46:28 -0600 Subject: [PATCH 0756/1342] zd1211rw: fix unaligned access in zd_mac_rx Fix an unaligned memory access in the zd_mac_rx function of zd1211rw that causes problems on SPARC64. Signed-off-by: Patrick Simmons Signed-off-by: John W. Linville --- drivers/net/wireless/zd1211rw/zd_mac.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/wireless/zd1211rw/zd_mac.c b/drivers/net/wireless/zd1211rw/zd_mac.c index 40b07b98822..3bd3c779fff 100644 --- a/drivers/net/wireless/zd1211rw/zd_mac.c +++ b/drivers/net/wireless/zd1211rw/zd_mac.c @@ -698,7 +698,7 @@ int zd_mac_rx(struct ieee80211_hw *hw, const u8 *buffer, unsigned int length) && !mac->pass_ctrl) return 0; - fc = *(__le16 *)buffer; + fc = get_unaligned((__le16*)buffer); need_padding = ieee80211_is_data_qos(fc) ^ ieee80211_has_a4(fc); skb = dev_alloc_skb(length + (need_padding ? 2 : 0)); -- GitLab From c37457e69ffd7d3c94cbfcc1c39be9a45dd7ad21 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Mon, 3 Aug 2009 11:11:45 +0200 Subject: [PATCH 0757/1342] drivers/net/wireless/iwlwifi: introduce missing kfree Move orthogonal error handling code up before a kzalloc, so that it doesn't have to free the allocated data. The semantic match that finds the problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // @r exists@ local idexpression x; statement S; expression E; identifier f,f1,l; position p1,p2; expression *ptr != NULL; @@ x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...); ... if (x == NULL) S <... when != x when != if (...) { <+...x...+> } ( x->f1 = E | (x->f1 == NULL || ...) | f(...,x->f1,...) ) ...> ( return \(0\|<+...x...+>\|ptr\); | return@p2 ...; ) @script:python@ p1 << r.p1; p2 << r.p2; @@ print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line) // Signed-off-by: Julia Lawall Acked-by: Zhu Yi Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-debugfs.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/drivers/net/wireless/iwlwifi/iwl-debugfs.c b/drivers/net/wireless/iwlwifi/iwl-debugfs.c index 11e08c06891..ca00cc8ad4c 100644 --- a/drivers/net/wireless/iwlwifi/iwl-debugfs.c +++ b/drivers/net/wireless/iwlwifi/iwl-debugfs.c @@ -308,18 +308,18 @@ static ssize_t iwl_dbgfs_nvm_read(struct file *file, return -ENODATA; } + ptr = priv->eeprom; + if (!ptr) { + IWL_ERR(priv, "Invalid EEPROM/OTP memory\n"); + return -ENOMEM; + } + /* 4 characters for byte 0xYY */ buf = kzalloc(buf_size, GFP_KERNEL); if (!buf) { IWL_ERR(priv, "Can not allocate Buffer\n"); return -ENOMEM; } - - ptr = priv->eeprom; - if (!ptr) { - IWL_ERR(priv, "Invalid EEPROM/OTP memory\n"); - return -ENOMEM; - } pos += scnprintf(buf + pos, buf_size - pos, "NVM Type: %s\n", (priv->nvm_device_type == NVM_DEVICE_TYPE_OTP) ? "OTP" : "EEPROM"); -- GitLab From 9f9857bb5e147b977b9878c46e3dd87c9e8caf50 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Sat, 1 Aug 2009 10:55:53 +0200 Subject: [PATCH 0758/1342] drivers/net/wireless: introduce missing kfree Error handling code following a kzalloc should free the allocated data. The semantic match that finds the problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // @r exists@ local idexpression x; statement S; expression E; identifier f,f1,l; position p1,p2; expression *ptr != NULL; @@ x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...); ... if (x == NULL) S <... when != x when != if (...) { <+...x...+> } ( x->f1 = E | (x->f1 == NULL || ...) | f(...,x->f1,...) ) ...> ( return \(0\|<+...x...+>\|ptr\); | return@p2 ...; ) @script:python@ p1 << r.p1; p2 << r.p2; @@ print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line) // Signed-off-by: Julia Lawall Signed-off-by: John W. Linville --- drivers/net/wireless/iwmc3200wifi/commands.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/net/wireless/iwmc3200wifi/commands.c b/drivers/net/wireless/iwmc3200wifi/commands.c index 834a7f544e5..e2334d12359 100644 --- a/drivers/net/wireless/iwmc3200wifi/commands.c +++ b/drivers/net/wireless/iwmc3200wifi/commands.c @@ -220,6 +220,7 @@ int iwm_store_rxiq_calib_result(struct iwm_priv *iwm) eeprom_rxiq = iwm_eeprom_access(iwm, IWM_EEPROM_CALIB_RXIQ); if (IS_ERR(eeprom_rxiq)) { IWM_ERR(iwm, "Couldn't access EEPROM RX IQ entry\n"); + kfree(rxiq); return PTR_ERR(eeprom_rxiq); } -- GitLab From b929c633b4067be18a335d278a66fd5deef3cabe Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Sun, 2 Aug 2009 09:44:12 +0200 Subject: [PATCH 0759/1342] libertas: Read buffer overflow Check whether index is within bounds before testing the element. Signed-off-by: Roel Kluin Signed-off-by: John W. Linville --- drivers/net/wireless/libertas/11d.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/wireless/libertas/11d.c b/drivers/net/wireless/libertas/11d.c index 9a5408e7d94..5c6968101f0 100644 --- a/drivers/net/wireless/libertas/11d.c +++ b/drivers/net/wireless/libertas/11d.c @@ -47,7 +47,7 @@ static u8 lbs_region_2_code(u8 *region) { u8 i; - for (i = 0; region[i] && i < COUNTRY_CODE_LEN; i++) + for (i = 0; i < COUNTRY_CODE_LEN && region[i]; i++) region[i] = toupper(region[i]); for (i = 0; i < ARRAY_SIZE(region_code_mapping); i++) { -- GitLab From 99f1b01562b7dcae75b043114f76163fbf84fcab Mon Sep 17 00:00:00 2001 From: Reinette Chatre Date: Mon, 3 Aug 2009 12:10:16 -0700 Subject: [PATCH 0760/1342] iwlagn: do not send key clear commands when rfkill enabled Do all key clearing except sending sommands to device when rfkill enabled. When rfkill enabled the interface is brought down and will be brought back up correctly after rfkill is enabled again. Same change is not needed for iwl3945 as it ignores return code when sending key clearing command to device. This fixes http://bugzilla.kernel.org/show_bug.cgi?id=13742 Signed-off-by: Reinette Chatre Tested-by: Frans Pop Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-sta.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/drivers/net/wireless/iwlwifi/iwl-sta.c b/drivers/net/wireless/iwlwifi/iwl-sta.c index 2addf735b19..ffd5c61a755 100644 --- a/drivers/net/wireless/iwlwifi/iwl-sta.c +++ b/drivers/net/wireless/iwlwifi/iwl-sta.c @@ -566,6 +566,8 @@ int iwl_remove_default_wep_key(struct iwl_priv *priv, unsigned long flags; spin_lock_irqsave(&priv->sta_lock, flags); + IWL_DEBUG_WEP(priv, "Removing default WEP key: idx=%d\n", + keyconf->keyidx); if (!test_and_clear_bit(keyconf->keyidx, &priv->ucode_key_table)) IWL_ERR(priv, "index %d not used in uCode key table.\n", @@ -573,6 +575,11 @@ int iwl_remove_default_wep_key(struct iwl_priv *priv, priv->default_wep_key--; memset(&priv->wep_keys[keyconf->keyidx], 0, sizeof(priv->wep_keys[0])); + if (iwl_is_rfkill(priv)) { + IWL_DEBUG_WEP(priv, "Not sending REPLY_WEPKEY command due to RFKILL.\n"); + spin_unlock_irqrestore(&priv->sta_lock, flags); + return 0; + } ret = iwl_send_static_wepkey_cmd(priv, 1); IWL_DEBUG_WEP(priv, "Remove default WEP key: idx=%d ret=%d\n", keyconf->keyidx, ret); @@ -853,6 +860,11 @@ int iwl_remove_dynamic_key(struct iwl_priv *priv, priv->stations[sta_id].sta.sta.modify_mask = STA_MODIFY_KEY_MASK; priv->stations[sta_id].sta.mode = STA_CONTROL_MODIFY_MSK; + if (iwl_is_rfkill(priv)) { + IWL_DEBUG_WEP(priv, "Not sending REPLY_ADD_STA command because RFKILL enabled. \n"); + spin_unlock_irqrestore(&priv->sta_lock, flags); + return 0; + } ret = iwl_send_add_sta(priv, &priv->stations[sta_id].sta, CMD_ASYNC); spin_unlock_irqrestore(&priv->sta_lock, flags); return ret; -- GitLab From 6c6c51e4cc11a5456fb1172008f7c69d955af9f6 Mon Sep 17 00:00:00 2001 From: Paul Mackerras Date: Mon, 3 Aug 2009 22:47:32 +1000 Subject: [PATCH 0761/1342] x86: Add quirk to make Apple MacBook5,2 use reboot=pci The latest Apple MacBook (MacBook5,2) doesn't reboot successfully under Linux; neither the EFI reboot method nor the default method using the keyboard controller works (the system just hangs and doesn't reset). However, the method using the "PCI reset register" at 0xcf9 does work. This adds a quirk to detect this machine via DMI and force the reboot_type to BOOT_CF9. With this it reboots successfully without requiring a command-line option. Note that the EFI code forces reboot_type to BOOT_EFI when the machine is booted via EFI, but this overrides that since the core_initcall runs after the EFI initialization code. Signed-off-by: Paul Mackerras LKML-Reference: <19062.56420.501516.316181@cargo.ozlabs.ibm.com> Signed-off-by: H. Peter Anvin --- arch/x86/kernel/reboot.c | 34 +++++++++++++++++++++++++++++++++- 1 file changed, 33 insertions(+), 1 deletion(-) diff --git a/arch/x86/kernel/reboot.c b/arch/x86/kernel/reboot.c index 508e982dd07..834c9da8bf9 100644 --- a/arch/x86/kernel/reboot.c +++ b/arch/x86/kernel/reboot.c @@ -3,6 +3,7 @@ #include #include #include +#include #include #include #include @@ -17,7 +18,6 @@ #include #ifdef CONFIG_X86_32 -# include # include # include #else @@ -404,6 +404,38 @@ EXPORT_SYMBOL(machine_real_restart); #endif /* CONFIG_X86_32 */ +/* + * Apple MacBook5,2 (2009 MacBook) needs reboot=p + */ +static int __init set_pci_reboot(const struct dmi_system_id *d) +{ + if (reboot_type != BOOT_CF9) { + reboot_type = BOOT_CF9; + printk(KERN_INFO "%s series board detected. " + "Selecting PCI-method for reboots.\n", d->ident); + } + return 0; +} + +static struct dmi_system_id __initdata pci_reboot_dmi_table[] = { + { /* Handle problems with rebooting on Apple MacBook5,2 */ + .callback = set_pci_reboot, + .ident = "Apple MacBook", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Apple Inc."), + DMI_MATCH(DMI_PRODUCT_NAME, "MacBook5,2"), + }, + }, + { } +}; + +static int __init pci_reboot_init(void) +{ + dmi_check_system(pci_reboot_dmi_table); + return 0; +} +core_initcall(pci_reboot_init); + static inline void kb_wait(void) { int i; -- GitLab From 6a7bbd57ed50bb62c9a81ae5f2e202ca689e5964 Mon Sep 17 00:00:00 2001 From: Paul Mackerras Date: Mon, 3 Aug 2009 22:38:10 +1000 Subject: [PATCH 0762/1342] x86: Make 64-bit efi_ioremap use ioremap on MMIO regions Booting current 64-bit x86 kernels on the latest Apple MacBook (MacBook5,2) via EFI gives the following warning: [ 0.182209] ------------[ cut here ]------------ [ 0.182222] WARNING: at arch/x86/mm/pageattr.c:581 __cpa_process_fault+0x44/0xa0() [ 0.182227] Hardware name: MacBook5,2 [ 0.182231] CPA: called for zero pte. vaddr = ffff8800ffe00000 cpa->vaddr = ffff8800ffe00000 [ 0.182236] Modules linked in: [ 0.182242] Pid: 0, comm: swapper Not tainted 2.6.31-rc4 #6 [ 0.182246] Call Trace: [ 0.182254] [] ? __cpa_process_fault+0x44/0xa0 [ 0.182261] [] warn_slowpath_common+0x78/0xd0 [ 0.182266] [] warn_slowpath_fmt+0x64/0x70 [ 0.182272] [] ? update_page_count+0x3c/0x50 [ 0.182280] [] ? phys_pmd_init+0x140/0x22e [ 0.182286] [] __cpa_process_fault+0x44/0xa0 [ 0.182292] [] __change_page_attr_set_clr+0x5f0/0xb40 [ 0.182301] [] ? vm_unmap_aliases+0x175/0x190 [ 0.182307] [] change_page_attr_set_clr+0xfe/0x3d0 [ 0.182314] [] _set_memory_uc+0x2a/0x30 [ 0.182319] [] set_memory_uc+0x7b/0xb0 [ 0.182327] [] efi_enter_virtual_mode+0x2ad/0x2c9 [ 0.182334] [] start_kernel+0x2db/0x3f4 [ 0.182340] [] x86_64_start_reservations+0x99/0xb9 [ 0.182345] [] x86_64_start_kernel+0xe0/0xf2 [ 0.182357] ---[ end trace 4eaa2a86a8e2da22 ]--- [ 0.182982] init_memory_mapping: 00000000ffffc000-0000000100000000 [ 0.182993] 00ffffc000 - 0100000000 page 4k This happens because the 64-bit version of efi_ioremap calls init_memory_mapping for all addresses, regardless of whether they are RAM or MMIO. The EFI tables on this machine ask for runtime access to some MMIO regions: [ 0.000000] EFI: mem195: type=11, attr=0x8000000000000000, range=[0x0000000093400000-0x0000000093401000) (0MB) [ 0.000000] EFI: mem196: type=11, attr=0x8000000000000000, range=[0x00000000ffc00000-0x00000000ffc40000) (0MB) [ 0.000000] EFI: mem197: type=11, attr=0x8000000000000000, range=[0x00000000ffc40000-0x00000000ffc80000) (0MB) [ 0.000000] EFI: mem198: type=11, attr=0x8000000000000000, range=[0x00000000ffc80000-0x00000000ffca4000) (0MB) [ 0.000000] EFI: mem199: type=11, attr=0x8000000000000000, range=[0x00000000ffca4000-0x00000000ffcb4000) (0MB) [ 0.000000] EFI: mem200: type=11, attr=0x8000000000000000, range=[0x00000000ffcb4000-0x00000000ffffc000) (3MB) [ 0.000000] EFI: mem201: type=11, attr=0x8000000000000000, range=[0x00000000ffffc000-0x0000000100000000) (0MB) This arranges to pass the EFI memory type through to efi_ioremap, and makes efi_ioremap use ioremap rather than init_memory_mapping if the type is EFI_MEMORY_MAPPED_IO. With this, the above warning goes away. Signed-off-by: Paul Mackerras LKML-Reference: <19062.55858.533494.471153@cargo.ozlabs.ibm.com> Cc: Huang Ying Signed-off-by: H. Peter Anvin --- arch/x86/include/asm/efi.h | 5 +++-- arch/x86/kernel/efi.c | 2 +- arch/x86/kernel/efi_64.c | 6 +++++- 3 files changed, 9 insertions(+), 4 deletions(-) diff --git a/arch/x86/include/asm/efi.h b/arch/x86/include/asm/efi.h index edc90f23e70..8406ed7f992 100644 --- a/arch/x86/include/asm/efi.h +++ b/arch/x86/include/asm/efi.h @@ -33,7 +33,7 @@ extern unsigned long asmlinkage efi_call_phys(void *, ...); #define efi_call_virt6(f, a1, a2, a3, a4, a5, a6) \ efi_call_virt(f, a1, a2, a3, a4, a5, a6) -#define efi_ioremap(addr, size) ioremap_cache(addr, size) +#define efi_ioremap(addr, size, type) ioremap_cache(addr, size) #else /* !CONFIG_X86_32 */ @@ -84,7 +84,8 @@ extern u64 efi_call6(void *fp, u64 arg1, u64 arg2, u64 arg3, efi_call6((void *)(efi.systab->runtime->f), (u64)(a1), (u64)(a2), \ (u64)(a3), (u64)(a4), (u64)(a5), (u64)(a6)) -extern void __iomem *efi_ioremap(unsigned long addr, unsigned long size); +extern void __iomem *efi_ioremap(unsigned long addr, unsigned long size, + u32 type); #endif /* CONFIG_X86_32 */ diff --git a/arch/x86/kernel/efi.c b/arch/x86/kernel/efi.c index 96f7ac0bbf0..19ccf6d0dcc 100644 --- a/arch/x86/kernel/efi.c +++ b/arch/x86/kernel/efi.c @@ -512,7 +512,7 @@ void __init efi_enter_virtual_mode(void) && end_pfn <= max_pfn_mapped)) va = __va(md->phys_addr); else - va = efi_ioremap(md->phys_addr, size); + va = efi_ioremap(md->phys_addr, size, md->type); md->virt_addr = (u64) (unsigned long) va; diff --git a/arch/x86/kernel/efi_64.c b/arch/x86/kernel/efi_64.c index 22c3b7828c5..ac0621a7ac3 100644 --- a/arch/x86/kernel/efi_64.c +++ b/arch/x86/kernel/efi_64.c @@ -98,10 +98,14 @@ void __init efi_call_phys_epilog(void) early_runtime_code_mapping_set_exec(0); } -void __iomem *__init efi_ioremap(unsigned long phys_addr, unsigned long size) +void __iomem *__init efi_ioremap(unsigned long phys_addr, unsigned long size, + u32 type) { unsigned long last_map_pfn; + if (type == EFI_MEMORY_MAPPED_IO) + return ioremap(phys_addr, size); + last_map_pfn = init_memory_mapping(phys_addr, phys_addr + size); if ((last_map_pfn << PAGE_SHIFT) < phys_addr + size) return NULL; -- GitLab From 4486d6ede16b362f89b29845af6fe1a26ae78a54 Mon Sep 17 00:00:00 2001 From: Jeff Layton Date: Mon, 3 Aug 2009 12:45:10 -0400 Subject: [PATCH 0763/1342] cifs: show noforceuid/noforcegid mount options (try #2) Since forceuid is the default, we now need to show when it's disabled. Signed-off-by: Jeff Layton Signed-off-by: Steve French --- fs/cifs/cifsfs.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/fs/cifs/cifsfs.c b/fs/cifs/cifsfs.c index 44f30504b82..84b75253b05 100644 --- a/fs/cifs/cifsfs.c +++ b/fs/cifs/cifsfs.c @@ -376,10 +376,14 @@ cifs_show_options(struct seq_file *s, struct vfsmount *m) seq_printf(s, ",uid=%d", cifs_sb->mnt_uid); if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_OVERR_UID) seq_printf(s, ",forceuid"); + else + seq_printf(s, ",noforceuid"); seq_printf(s, ",gid=%d", cifs_sb->mnt_gid); if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_OVERR_GID) seq_printf(s, ",forcegid"); + else + seq_printf(s, ",noforcegid"); cifs_show_address(s, tcon->ses->server); -- GitLab From 24e2fb615fd6b624c320cec9ea9d91a75dad902e Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Sun, 2 Aug 2009 13:00:18 +0200 Subject: [PATCH 0764/1342] cifs: Read buffer overflow Check whether index is within bounds before testing the element. Acked-by: Jeff Layton Signed-off-by: Roel Kluin Signed-off-by: Steve French --- fs/cifs/cifs_unicode.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/cifs/cifs_unicode.c b/fs/cifs/cifs_unicode.c index 60e3c4253de..714a542cbaf 100644 --- a/fs/cifs/cifs_unicode.c +++ b/fs/cifs/cifs_unicode.c @@ -44,7 +44,7 @@ cifs_ucs2_bytes(const __le16 *from, int maxbytes, int maxwords = maxbytes / 2; char tmp[NLS_MAX_CHARSET_SIZE]; - for (i = 0; from[i] && i < maxwords; i++) { + for (i = 0; i < maxwords && from[i]; i++) { charlen = codepage->uni2char(le16_to_cpu(from[i]), tmp, NLS_MAX_CHARSET_SIZE); if (charlen > 0) -- GitLab From d2ba8b211bb8abc29aa627dbd4dce08cfbc8082b Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Mon, 3 Aug 2009 14:44:54 -0700 Subject: [PATCH 0765/1342] x86: Fix assert syntax in vmlinux.lds.S Older versions of binutils did not accept the naked "ASSERT" syntax; it is considered an expression whose value needs to be assigned to something. Reported-tested-and-fixed-by: Jean Delvare Signed-off-by: H. Peter Anvin --- arch/x86/kernel/vmlinux.lds.S | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) diff --git a/arch/x86/kernel/vmlinux.lds.S b/arch/x86/kernel/vmlinux.lds.S index 59f31d2dd43..78d185d797d 100644 --- a/arch/x86/kernel/vmlinux.lds.S +++ b/arch/x86/kernel/vmlinux.lds.S @@ -393,8 +393,8 @@ SECTIONS #ifdef CONFIG_X86_32 -ASSERT((_end - LOAD_OFFSET <= KERNEL_IMAGE_SIZE), - "kernel image bigger than KERNEL_IMAGE_SIZE") +. = ASSERT((_end - LOAD_OFFSET <= KERNEL_IMAGE_SIZE), + "kernel image bigger than KERNEL_IMAGE_SIZE"); #else /* * Per-cpu symbols which need to be offset from __per_cpu_load @@ -407,12 +407,12 @@ INIT_PER_CPU(irq_stack_union); /* * Build-time check on the image size: */ -ASSERT((_end - _text <= KERNEL_IMAGE_SIZE), - "kernel image bigger than KERNEL_IMAGE_SIZE") +. = ASSERT((_end - _text <= KERNEL_IMAGE_SIZE), + "kernel image bigger than KERNEL_IMAGE_SIZE"); #ifdef CONFIG_SMP -ASSERT((per_cpu__irq_stack_union == 0), - "irq_stack_union is not at start of per-cpu area"); +. = ASSERT((per_cpu__irq_stack_union == 0), + "irq_stack_union is not at start of per-cpu area"); #endif #endif /* CONFIG_X86_32 */ @@ -420,7 +420,7 @@ ASSERT((per_cpu__irq_stack_union == 0), #ifdef CONFIG_KEXEC #include -ASSERT(kexec_control_code_size <= KEXEC_CONTROL_CODE_MAX_SIZE, - "kexec control code size is too big") +. = ASSERT(kexec_control_code_size <= KEXEC_CONTROL_CODE_MAX_SIZE, + "kexec control code size is too big"); #endif -- GitLab From bab9a3da93bfe09c609407dedae5708b07a7ac56 Mon Sep 17 00:00:00 2001 From: Borislav Petkov Date: Thu, 30 Jul 2009 11:10:01 +0200 Subject: [PATCH 0766/1342] x86, msr: execute on the correct CPU subset Make rdmsr_on_cpus/wrmsr_on_cpus execute on the current CPU only if it is in the supplied bitmask. Signed-off-by: Borislav Petkov Signed-off-by: H. Peter Anvin --- arch/x86/lib/msr.c | 26 ++++++++++---------------- 1 file changed, 10 insertions(+), 16 deletions(-) diff --git a/arch/x86/lib/msr.c b/arch/x86/lib/msr.c index 1440b9c0547..caa24aca811 100644 --- a/arch/x86/lib/msr.c +++ b/arch/x86/lib/msr.c @@ -89,16 +89,13 @@ void rdmsr_on_cpus(const cpumask_t *mask, u32 msr_no, struct msr *msrs) rv.msrs = msrs; rv.msr_no = msr_no; - preempt_disable(); - /* - * FIXME: handle the CPU we're executing on separately for now until - * smp_call_function_many has been fixed to not skip it. - */ - this_cpu = raw_smp_processor_id(); - smp_call_function_single(this_cpu, __rdmsr_on_cpu, &rv, 1); + this_cpu = get_cpu(); + + if (cpumask_test_cpu(this_cpu, mask)) + __rdmsr_on_cpu(&rv); smp_call_function_many(mask, __rdmsr_on_cpu, &rv, 1); - preempt_enable(); + put_cpu(); } EXPORT_SYMBOL(rdmsr_on_cpus); @@ -121,16 +118,13 @@ void wrmsr_on_cpus(const cpumask_t *mask, u32 msr_no, struct msr *msrs) rv.msrs = msrs; rv.msr_no = msr_no; - preempt_disable(); - /* - * FIXME: handle the CPU we're executing on separately for now until - * smp_call_function_many has been fixed to not skip it. - */ - this_cpu = raw_smp_processor_id(); - smp_call_function_single(this_cpu, __wrmsr_on_cpu, &rv, 1); + this_cpu = get_cpu(); + + if (cpumask_test_cpu(this_cpu, mask)) + __wrmsr_on_cpu(&rv); smp_call_function_many(mask, __wrmsr_on_cpu, &rv, 1); - preempt_enable(); + put_cpu(); } EXPORT_SYMBOL(wrmsr_on_cpus); -- GitLab From f1f029c7bfbf4ee1918b90a431ab823bed812504 Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Mon, 3 Aug 2009 16:33:40 -0700 Subject: [PATCH 0767/1342] x86: fix assembly constraints in native_save_fl() From Gabe Black in bugzilla 13888: native_save_fl is implemented as follows: 11static inline unsigned long native_save_fl(void) 12{ 13 unsigned long flags; 14 15 asm volatile("# __raw_save_flags\n\t" 16 "pushf ; pop %0" 17 : "=g" (flags) 18 : /* no input */ 19 : "memory"); 20 21 return flags; 22} If gcc chooses to put flags on the stack, for instance because this is inlined into a larger function with more register pressure, the offset of the flags variable from the stack pointer will change when the pushf is performed. gcc doesn't attempt to understand that fact, and address used for pop will still be the same. It will write to somewhere near flags on the stack but not actually into it and overwrite some other value. I saw this happen in the ide_device_add_all function when running in a simulator I work on. I'm assuming that some quirk of how the simulated hardware is set up caused the code path this is on to be executed when it normally wouldn't. A simple fix might be to change "=g" to "=r". Reported-by: Gabe Black Signed-off-by: H. Peter Anvin Cc: Stable Team --- arch/x86/include/asm/irqflags.h | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/arch/x86/include/asm/irqflags.h b/arch/x86/include/asm/irqflags.h index 2bdab21f089..c6ccbe7e81a 100644 --- a/arch/x86/include/asm/irqflags.h +++ b/arch/x86/include/asm/irqflags.h @@ -12,9 +12,15 @@ static inline unsigned long native_save_fl(void) { unsigned long flags; + /* + * Note: this needs to be "=r" not "=rm", because we have the + * stack offset from what gcc expects at the time the "pop" is + * executed, and so a memory reference with respect to the stack + * would end up using the wrong address. + */ asm volatile("# __raw_save_flags\n\t" "pushf ; pop %0" - : "=g" (flags) + : "=r" (flags) : /* no input */ : "memory"); -- GitLab From f6caa14aa0b126d4a2933907d1519611b2a8524a Mon Sep 17 00:00:00 2001 From: Mike McCormack Date: Fri, 31 Jul 2009 01:57:42 +0000 Subject: [PATCH 0768/1342] sky2: Avoid transmits during sky2_down() This patch supersedes my previous patch "sky2: Avoid transmitting during sky2_restart". I have reworked the patch to avoid crashes during both sky2_restart() and sky2_set_ringparam(). Without this patch, the sky2 driver can be crashed by doing: # pktgen eth1 & (transmit many packets on eth1) # ethtool -G eth1 tx 510 I am aware you object to storing extra state, but I can't see a way around this. Without remembering that we're restarting, netif_wake_queue() is called in the ISR from sky2_tx_complete(), and netif_tx_lock() is used in sky2_tx_done(). If anybody can see a way around this, please let me know. Signed-off-by: Mike McCormack Signed-off-by: David S. Miller --- drivers/net/sky2.c | 14 +++++++++++++- drivers/net/sky2.h | 1 + 2 files changed, 14 insertions(+), 1 deletion(-) diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index 3550c5dcd93..0a551d8f5d9 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -1488,6 +1488,8 @@ static int sky2_up(struct net_device *dev) sky2_set_vlan_mode(hw, port, sky2->vlgrp != NULL); #endif + sky2->restarting = 0; + err = sky2_rx_start(sky2); if (err) goto err_out; @@ -1500,6 +1502,9 @@ static int sky2_up(struct net_device *dev) sky2_set_multicast(dev); + /* wake queue incase we are restarting */ + netif_wake_queue(dev); + if (netif_msg_ifup(sky2)) printk(KERN_INFO PFX "%s: enabling interface\n", dev->name); return 0; @@ -1533,6 +1538,8 @@ static inline int tx_dist(unsigned tail, unsigned head) /* Number of list elements available for next tx */ static inline int tx_avail(const struct sky2_port *sky2) { + if (unlikely(sky2->restarting)) + return 0; return sky2->tx_pending - tx_dist(sky2->tx_cons, sky2->tx_prod); } @@ -1818,6 +1825,10 @@ static int sky2_down(struct net_device *dev) if (netif_msg_ifdown(sky2)) printk(KERN_INFO PFX "%s: disabling interface\n", dev->name); + /* explicitly shut off tx incase we're restarting */ + sky2->restarting = 1; + netif_tx_disable(dev); + /* Force flow control off */ sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF); @@ -2359,7 +2370,7 @@ static inline void sky2_tx_done(struct net_device *dev, u16 last) { struct sky2_port *sky2 = netdev_priv(dev); - if (netif_running(dev)) { + if (likely(netif_running(dev) && !sky2->restarting)) { netif_tx_lock(dev); sky2_tx_complete(sky2, last); netif_tx_unlock(dev); @@ -4283,6 +4294,7 @@ static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw, spin_lock_init(&sky2->phy_lock); sky2->tx_pending = TX_DEF_PENDING; sky2->rx_pending = RX_DEF_PENDING; + sky2->restarting = 0; hw->dev[port] = dev; diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h index b5549c9e510..4486b066b43 100644 --- a/drivers/net/sky2.h +++ b/drivers/net/sky2.h @@ -2051,6 +2051,7 @@ struct sky2_port { u8 duplex; /* DUPLEX_HALF, DUPLEX_FULL */ u8 rx_csum; u8 wol; + u8 restarting; enum flow_control flow_mode; enum flow_control flow_status; -- GitLab From 7781de74568bddfefbd2d32a934a8c791a2420cd Mon Sep 17 00:00:00 2001 From: Jakob Bornecrantz Date: Mon, 3 Aug 2009 13:43:58 +0100 Subject: [PATCH 0769/1342] drm: Small logic fix in drm_mode_setcrtc Match the logic to the comments in the debug message Signed-off-by: Jakob Bornecrantz Signed-off-by: Dave Airlie --- drivers/gpu/drm/drm_crtc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/gpu/drm/drm_crtc.c b/drivers/gpu/drm/drm_crtc.c index 8fab7890a36..33be210d672 100644 --- a/drivers/gpu/drm/drm_crtc.c +++ b/drivers/gpu/drm/drm_crtc.c @@ -1461,7 +1461,7 @@ int drm_mode_setcrtc(struct drm_device *dev, void *data, goto out; } - if (crtc_req->count_connectors > 0 && !mode && !fb) { + if (crtc_req->count_connectors > 0 && (!mode || !fb)) { DRM_DEBUG("Count connectors is %d but no mode or fb set\n", crtc_req->count_connectors); ret = -EINVAL; -- GitLab From 4cb72b1727140f131b2df5f37c2e54f5965f98c2 Mon Sep 17 00:00:00 2001 From: Jakob Bornecrantz Date: Mon, 3 Aug 2009 13:43:59 +0100 Subject: [PATCH 0770/1342] drm: Catch stop possible NULL pointer reference This was caught by Weiss. Also added some comments to the fb_changed and mode_changed variables to explain what they do. Signed-off-by: Jakob Bornecrantz Tested-by: Thomas White Signed-off-by: Dave Airlie --- drivers/gpu/drm/drm_crtc_helper.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/gpu/drm/drm_crtc_helper.c b/drivers/gpu/drm/drm_crtc_helper.c index 3da9cfa3184..6aaa2cb2336 100644 --- a/drivers/gpu/drm/drm_crtc_helper.c +++ b/drivers/gpu/drm/drm_crtc_helper.c @@ -706,8 +706,8 @@ int drm_crtc_helper_set_config(struct drm_mode_set *set) struct drm_encoder **save_encoders, *new_encoder; struct drm_framebuffer *old_fb = NULL; bool save_enabled; - bool mode_changed = false; - bool fb_changed = false; + bool mode_changed = false; /* if true do a full mode set */ + bool fb_changed = false; /* if true and !mode_changed just do a flip */ struct drm_connector *connector; int count = 0, ro, fail = 0; struct drm_crtc_helper_funcs *crtc_funcs; @@ -758,6 +758,8 @@ int drm_crtc_helper_set_config(struct drm_mode_set *set) if (set->crtc->fb == NULL) { DRM_DEBUG("crtc has no fb, full mode set\n"); mode_changed = true; + } else if (set->fb == NULL) { + mode_changed = true; } else if ((set->fb->bits_per_pixel != set->crtc->fb->bits_per_pixel) || set->fb->depth != set->crtc->fb->depth) -- GitLab From 7320700df1864b601cef5adbddce8654a0e3f78b Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Mon, 3 Aug 2009 17:01:53 -0400 Subject: [PATCH 0771/1342] drm/radeon: add some new r7xx pci ids Signed-off-by: Alex Deucher Signed-off-by: Dave Airlie --- include/drm/drm_pciids.h | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/include/drm/drm_pciids.h b/include/drm/drm_pciids.h index 7174818c2c1..9d4c0049154 100644 --- a/include/drm/drm_pciids.h +++ b/include/drm/drm_pciids.h @@ -257,9 +257,12 @@ {0x1002, 0x940F, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R600|RADEON_NEW_MEMMAP}, \ {0x1002, 0x94A0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV740|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \ {0x1002, 0x94A1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV740|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \ + {0x1002, 0x94A3, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV740|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \ {0x1002, 0x94B1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV740|RADEON_NEW_MEMMAP}, \ {0x1002, 0x94B3, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV740|RADEON_NEW_MEMMAP}, \ + {0x1002, 0x94B4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV740|RADEON_NEW_MEMMAP}, \ {0x1002, 0x94B5, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV740|RADEON_NEW_MEMMAP}, \ + {0x1002, 0x94B9, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV740|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \ {0x1002, 0x9440, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV770|RADEON_NEW_MEMMAP}, \ {0x1002, 0x9441, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV770|RADEON_NEW_MEMMAP}, \ {0x1002, 0x9442, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV770|RADEON_NEW_MEMMAP}, \ @@ -288,6 +291,7 @@ {0x1002, 0x948F, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV730|RADEON_NEW_MEMMAP}, \ {0x1002, 0x9490, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV730|RADEON_NEW_MEMMAP}, \ {0x1002, 0x9491, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV730|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \ + {0x1002, 0x9495, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV730|RADEON_NEW_MEMMAP}, \ {0x1002, 0x9498, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV730|RADEON_NEW_MEMMAP}, \ {0x1002, 0x949C, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV730|RADEON_NEW_MEMMAP}, \ {0x1002, 0x949E, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV730|RADEON_NEW_MEMMAP}, \ @@ -325,6 +329,7 @@ {0x1002, 0x9552, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV710|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \ {0x1002, 0x9553, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV710|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \ {0x1002, 0x9555, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV710|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \ + {0x1002, 0x9557, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV710|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \ {0x1002, 0x9580, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV630|RADEON_NEW_MEMMAP}, \ {0x1002, 0x9581, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV630|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \ {0x1002, 0x9583, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV630|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \ -- GitLab From 0924d942256ac470c5f7b4ebaf7fe0415fc6fa59 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 3 Aug 2009 12:03:03 +1000 Subject: [PATCH 0772/1342] drm/radeon/kms: fix rv515 VRAM initialisation. This got missed in the VRAM init re-workings. Signed-of-by: Dave Airlie --- drivers/gpu/drm/radeon/rv515.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/gpu/drm/radeon/rv515.c b/drivers/gpu/drm/radeon/rv515.c index 551e608702e..fd8f3ca716e 100644 --- a/drivers/gpu/drm/radeon/rv515.c +++ b/drivers/gpu/drm/radeon/rv515.c @@ -370,6 +370,7 @@ void rv515_vram_info(struct radeon_device *rdev) rv515_vram_get_type(rdev); + r100_vram_init_sizes(rdev); /* FIXME: we should enforce default clock in case GPU is not in * default setup */ -- GitLab From 6d0897ba58139523d37e97855ee0fe2d78629da6 Mon Sep 17 00:00:00 2001 From: Thomas Hellstrom Date: Fri, 31 Jul 2009 10:47:51 +0200 Subject: [PATCH 0773/1342] drm/ttm: Fix a potential comparison of structs. On some architectures the comparison may cause a compilation failure. Original partial fix Signed-off-by: Thomas Hellstrom Signed-off-by: Pekka Paalanen Signed-off-by: Dave Airlie --- drivers/gpu/drm/ttm/ttm_bo_util.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/gpu/drm/ttm/ttm_bo_util.c b/drivers/gpu/drm/ttm/ttm_bo_util.c index ce2e6f38ea0..ad4ada07c6c 100644 --- a/drivers/gpu/drm/ttm/ttm_bo_util.c +++ b/drivers/gpu/drm/ttm/ttm_bo_util.c @@ -150,7 +150,7 @@ static int ttm_copy_io_ttm_page(struct ttm_tt *ttm, void *src, #ifdef CONFIG_X86 dst = kmap_atomic_prot(d, KM_USER0, prot); #else - if (prot != PAGE_KERNEL) + if (pgprot_val(prot) != pgprot_val(PAGE_KERNEL)) dst = vmap(&d, 1, 0, prot); else dst = kmap(d); @@ -163,7 +163,7 @@ static int ttm_copy_io_ttm_page(struct ttm_tt *ttm, void *src, #ifdef CONFIG_X86 kunmap_atomic(dst, KM_USER0); #else - if (prot != PAGE_KERNEL) + if (pgprot_val(prot) != pgprot_val(PAGE_KERNEL)) vunmap(dst); else kunmap(d); @@ -186,7 +186,7 @@ static int ttm_copy_ttm_io_page(struct ttm_tt *ttm, void *dst, #ifdef CONFIG_X86 src = kmap_atomic_prot(s, KM_USER0, prot); #else - if (prot != PAGE_KERNEL) + if (pgprot_val(prot) != pgprot_val(PAGE_KERNEL)) src = vmap(&s, 1, 0, prot); else src = kmap(s); @@ -199,7 +199,7 @@ static int ttm_copy_ttm_io_page(struct ttm_tt *ttm, void *dst, #ifdef CONFIG_X86 kunmap_atomic(src, KM_USER0); #else - if (prot != PAGE_KERNEL) + if (pgprot_val(prot) != pgprot_val(PAGE_KERNEL)) vunmap(src); else kunmap(s); -- GitLab From de05065ff5d6878523317ff4a0b48a1239f80f73 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 3 Aug 2009 12:05:34 +1000 Subject: [PATCH 0774/1342] drm/radeon/kms: fix nomodeset. The ordering was wrong to get the nomodeset parameter to work. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_drv.c | 17 ++++++++--------- 1 file changed, 8 insertions(+), 9 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon_drv.c b/drivers/gpu/drm/radeon/radeon_drv.c index 3cfcee17dc5..0bd5879a495 100644 --- a/drivers/gpu/drm/radeon/radeon_drv.c +++ b/drivers/gpu/drm/radeon/radeon_drv.c @@ -318,6 +318,14 @@ static int __init radeon_init(void) driver = &driver_old; driver->num_ioctls = radeon_max_ioctl; #if defined(CONFIG_DRM_RADEON_KMS) +#ifdef CONFIG_VGA_CONSOLE + if (vgacon_text_force() && radeon_modeset == -1) { + DRM_INFO("VGACON disable radeon kernel modesetting.\n"); + driver = &driver_old; + driver->driver_features &= ~DRIVER_MODESET; + radeon_modeset = 0; + } +#endif /* if enabled by default */ if (radeon_modeset == -1) { DRM_INFO("radeon default to kernel modesetting.\n"); @@ -329,17 +337,8 @@ static int __init radeon_init(void) driver->driver_features |= DRIVER_MODESET; driver->num_ioctls = radeon_max_kms_ioctl; } - /* if the vga console setting is enabled still * let modprobe override it */ -#ifdef CONFIG_VGA_CONSOLE - if (vgacon_text_force() && radeon_modeset == -1) { - DRM_INFO("VGACON disable radeon kernel modesetting.\n"); - driver = &driver_old; - driver->driver_features &= ~DRIVER_MODESET; - radeon_modeset = 0; - } -#endif #endif return drm_init(driver); } -- GitLab From c9b7fb54f0a51e587fa09be3a85666b43d36a850 Mon Sep 17 00:00:00 2001 From: Xiaotian Feng Date: Wed, 29 Jul 2009 21:28:24 +0800 Subject: [PATCH 0775/1342] drm/radeon/kms: fix memory leak in radeon_driver_load_kms This patch fixes following kmemleak report: unreferenced object 0xffff88022cb53000 (size 4096): comm "work_for_cpu", pid 97, jiffies 4294672345 backtrace: [] create_object+0x19f/0x2a0 [] kmemleak_alloc+0x26/0x4c [] __kmalloc+0x187/0x1b0 [] kzalloc.clone.0+0x13/0x15 [radeon] [] radeon_driver_load_kms+0x26/0xe1 [radeon] [] drm_get_dev+0x37f/0x480 [drm] [] radeon_pci_probe+0x15/0x269 [radeon] [] local_pci_probe+0x17/0x1b [] do_work_for_cpu+0x18/0x2a [] kthread+0x8a/0x92 [] child_rip+0xa/0x20 [] 0xffffffffffffffff Signed-off-by: Xiaotian Feng Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_kms.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/gpu/drm/radeon/radeon_kms.c b/drivers/gpu/drm/radeon/radeon_kms.c index 937a2f1cdb4..3357110e30c 100644 --- a/drivers/gpu/drm/radeon/radeon_kms.c +++ b/drivers/gpu/drm/radeon/radeon_kms.c @@ -58,6 +58,8 @@ int radeon_driver_load_kms(struct drm_device *dev, unsigned long flags) if (r) { DRM_ERROR("Failed to initialize radeon, disabling IOCTL\n"); radeon_device_fini(rdev); + kfree(rdev); + dev->dev_private = NULL; return r; } return 0; -- GitLab From fee280d3fd9bc5247bef9f4ab35a4693bfffdcfd Mon Sep 17 00:00:00 2001 From: Thomas Hellstrom Date: Mon, 3 Aug 2009 12:39:06 +0200 Subject: [PATCH 0776/1342] drm/ttm: Fix a sync object leak. If there are multiple simultaneous waiters for the same buffer object, a temporary reference to its sync object may be leaked. Signed-off-by: Thomas Hellstrom Signed-off-by: Dave Airlie --- drivers/gpu/drm/ttm/ttm_bo.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/gpu/drm/ttm/ttm_bo.c b/drivers/gpu/drm/ttm/ttm_bo.c index 6538d423698..aa82d5370c3 100644 --- a/drivers/gpu/drm/ttm/ttm_bo.c +++ b/drivers/gpu/drm/ttm/ttm_bo.c @@ -1575,6 +1575,10 @@ int ttm_bo_wait(struct ttm_buffer_object *bo, driver->sync_obj_unref(&sync_obj); driver->sync_obj_unref(&tmp_obj); spin_lock(&bo->lock); + } else { + spin_unlock(&bo->lock); + driver->sync_obj_unref(&sync_obj); + spin_lock(&bo->lock); } } return 0; -- GitLab From fa99239cb73dbf419bea9f334b85ba94ac88a532 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Mon, 3 Aug 2009 14:20:32 +0200 Subject: [PATCH 0777/1342] drm/radeon: Read buffer overflow Check whether index is within bounds before grabbing the element. Signed-off-by: Roel Kluin Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index 05a44896dff..f1ba8ff4113 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -722,13 +722,14 @@ int r100_cs_packet_parse(struct radeon_cs_parser *p, unsigned idx) { struct radeon_cs_chunk *ib_chunk = &p->chunks[p->chunk_ib_idx]; - uint32_t header = ib_chunk->kdata[idx]; + uint32_t header; if (idx >= ib_chunk->length_dw) { DRM_ERROR("Can not parse packet at %d after CS end %d !\n", idx, ib_chunk->length_dw); return -EINVAL; } + header = ib_chunk->kdata[idx]; pkt->idx = idx; pkt->type = CP_PACKET_GET_TYPE(header); pkt->count = CP_PACKET_GET_COUNT(header); -- GitLab From c96e7c7a3a79931446ecf9494a8415e4d164ebd8 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Mon, 3 Aug 2009 14:22:53 +0200 Subject: [PATCH 0778/1342] drm/ttm: Read buffer overflow Check whether index is within bounds before grabbing the element. Signed-off-by: Roel Kluin Signed-off-by: Dave Airlie --- drivers/gpu/drm/ttm/ttm_bo.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/ttm/ttm_bo.c b/drivers/gpu/drm/ttm/ttm_bo.c index aa82d5370c3..c2b0d710d10 100644 --- a/drivers/gpu/drm/ttm/ttm_bo.c +++ b/drivers/gpu/drm/ttm/ttm_bo.c @@ -1182,13 +1182,14 @@ static int ttm_bo_force_list_clean(struct ttm_bo_device *bdev, int ttm_bo_clean_mm(struct ttm_bo_device *bdev, unsigned mem_type) { - struct ttm_mem_type_manager *man = &bdev->man[mem_type]; + struct ttm_mem_type_manager *man; int ret = -EINVAL; if (mem_type >= TTM_NUM_MEM_TYPES) { printk(KERN_ERR TTM_PFX "Illegal memory type %d\n", mem_type); return ret; } + man = &bdev->man[mem_type]; if (!man->has_type) { printk(KERN_ERR TTM_PFX "Trying to take down uninitialized " -- GitLab From d098564f3b2b5d555e51bca765a6a9e0dda8f2cd Mon Sep 17 00:00:00 2001 From: Steve French Date: Tue, 4 Aug 2009 03:53:28 +0000 Subject: [PATCH 0779/1342] [CIFS] Update readme to reflect forceuid mount parms Signed-off-by: Steve French --- fs/cifs/CHANGES | 3 ++- fs/cifs/README | 25 ++++++++++++------------- 2 files changed, 14 insertions(+), 14 deletions(-) diff --git a/fs/cifs/CHANGES b/fs/cifs/CHANGES index 651cefde385..e85b1e4389e 100644 --- a/fs/cifs/CHANGES +++ b/fs/cifs/CHANGES @@ -2,7 +2,8 @@ Version 1.60 ------------- Fix memory leak in reconnect. Fix oops in DFS mount error path. Set s_maxbytes to smaller (the max that vfs can handle) so that -sendfile will now work over cifs mounts again. +sendfile will now work over cifs mounts again. Add noforcegid +and noforceuid mount parameters. Version 1.59 ------------ diff --git a/fs/cifs/README b/fs/cifs/README index ad92921dbde..79c1a93400b 100644 --- a/fs/cifs/README +++ b/fs/cifs/README @@ -262,11 +262,11 @@ A partial list of the supported mount options follows: mount. domain Set the SMB/CIFS workgroup name prepended to the username during CIFS session establishment - forceuid Set the default uid for inodes based on the uid - passed in. For mounts to servers + forceuid Set the default uid for inodes to the uid + passed in on mount. For mounts to servers which do support the CIFS Unix extensions, such as a properly configured Samba server, the server provides - the uid, gid and mode so this parameter should not be + the uid, gid and mode so this parameter should not be specified unless the server and clients uid and gid numbering differ. If the server and client are in the same domain (e.g. running winbind or nss_ldap) and @@ -278,11 +278,7 @@ A partial list of the supported mount options follows: of existing files will be the uid (gid) of the person who executed the mount (root, except when mount.cifs is configured setuid for user mounts) unless the "uid=" - (gid) mount option is specified. For the uid (gid) of newly - created files and directories, ie files created since - the last mount of the server share, the expected uid - (gid) is cached as long as the inode remains in - memory on the client. Also note that permission + (gid) mount option is specified. Also note that permission checks (authorization checks) on accesses to a file occur at the server, but there are cases in which an administrator may want to restrict at the client as well. For those @@ -290,12 +286,15 @@ A partial list of the supported mount options follows: (such as Windows), permissions can also be checked at the client, and a crude form of client side permission checking can be enabled by specifying file_mode and dir_mode on - the client. Note that the mount.cifs helper must be - at version 1.10 or higher to support specifying the uid - (or gid) in non-numeric form. - forcegid (similar to above but for the groupid instead of uid) + the client. (default) + forcegid (similar to above but for the groupid instead of uid) (default) + noforceuid Fill in file owner information (uid) by requesting it from + the server if possible. With this option, the value given in + the uid= option (on mount) will only be used if the server + can not support returning uids on inodes. + noforcegid (similar to above but for the group owner, gid, instead of uid) uid Set the default uid for inodes, and indicate to the - cifs kernel driver which local user mounted . If the server + cifs kernel driver which local user mounted. If the server supports the unix extensions the default uid is not used to fill in the owner fields of inodes (files) unless the "forceuid" parameter is specified. -- GitLab From 0cb13536c3382004bd9b833565e2af33f26ed1fb Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Mon, 3 Aug 2009 21:10:01 -0700 Subject: [PATCH 0780/1342] 3c59x: Fix build failure with gcc 3.2 Fix the following build failure with gcc 3.2: CC [M] drivers/net/3c59x.o drivers/net/3c59x.c:2726:1: directives may not be used inside a macro argument drivers/net/3c59x.c:2725:59: unterminated argument list invoking macro "pr_err" drivers/net/3c59x.c: In function `dump_tx_ring': drivers/net/3c59x.c:2727: implicit declaration of function `pr_err' drivers/net/3c59x.c:2731: syntax error before ')' token Apparently gcc 3.2 doesn't like #if interleaved with a macro call. Signed-off-by: Jean Delvare Signed-off-by: David S. Miller --- drivers/net/3c59x.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-) diff --git a/drivers/net/3c59x.c b/drivers/net/3c59x.c index c34aee91250..c2041685094 100644 --- a/drivers/net/3c59x.c +++ b/drivers/net/3c59x.c @@ -2721,13 +2721,15 @@ dump_tx_ring(struct net_device *dev) &vp->tx_ring[vp->dirty_tx % TX_RING_SIZE]); issue_and_wait(dev, DownStall); for (i = 0; i < TX_RING_SIZE; i++) { - pr_err(" %d: @%p length %8.8x status %8.8x\n", i, - &vp->tx_ring[i], + unsigned int length; + #if DO_ZEROCOPY - le32_to_cpu(vp->tx_ring[i].frag[0].length), + length = le32_to_cpu(vp->tx_ring[i].frag[0].length); #else - le32_to_cpu(vp->tx_ring[i].length), + length = le32_to_cpu(vp->tx_ring[i].length); #endif + pr_err(" %d: @%p length %8.8x status %8.8x\n", + i, &vp->tx_ring[i], length, le32_to_cpu(vp->tx_ring[i].status)); } if (!stalled) -- GitLab From 70d715fd0597f18528f389b5ac59102263067744 Mon Sep 17 00:00:00 2001 From: Hiroshi Shimamoto Date: Mon, 3 Aug 2009 11:48:19 +0900 Subject: [PATCH 0781/1342] posix-timers: Fix oops in clock_nanosleep() with CLOCK_MONOTONIC_RAW Prevent calling do_nanosleep() with clockid CLOCK_MONOTONIC_RAW, it may cause oops, such as NULL pointer dereference. Signed-off-by: Hiroshi Shimamoto Cc: Andrew Morton Cc: Thomas Gleixner Cc: John Stultz Cc: LKML-Reference: <4A764FF3.50607@ct.jp.nec.com> Signed-off-by: Ingo Molnar --- kernel/posix-timers.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/kernel/posix-timers.c b/kernel/posix-timers.c index 052ec4d195c..d089d052c4a 100644 --- a/kernel/posix-timers.c +++ b/kernel/posix-timers.c @@ -202,6 +202,12 @@ static int no_timer_create(struct k_itimer *new_timer) return -EOPNOTSUPP; } +static int no_nsleep(const clockid_t which_clock, int flags, + struct timespec *tsave, struct timespec __user *rmtp) +{ + return -EOPNOTSUPP; +} + /* * Return nonzero if we know a priori this clockid_t value is bogus. */ @@ -254,6 +260,7 @@ static __init int init_posix_timers(void) .clock_get = posix_get_monotonic_raw, .clock_set = do_posix_clock_nosettime, .timer_create = no_timer_create, + .nsleep = no_nsleep, }; register_posix_clock(CLOCK_REALTIME, &clock_realtime); -- GitLab From 7e030655dda5b5efc4305e2a8f46c4967d32eb3d Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Sun, 2 Aug 2009 13:43:11 +0200 Subject: [PATCH 0782/1342] perf: Fix read buffer overflow Check whether index is within bounds before testing the element. Signed-off-by: Roel Kluin Cc: a.p.zijlstra@chello.nl Cc: Andrew Morton LKML-Reference: <4A757BCF.40101@gmail.com> Signed-off-by: Ingo Molnar --- tools/perf/builtin-report.c | 2 +- tools/perf/util/quote.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c index 95fd06cdaa9..ce4f28645e6 100644 --- a/tools/perf/builtin-report.c +++ b/tools/perf/builtin-report.c @@ -253,7 +253,7 @@ static int strcommon(const char *pathname) { int n = 0; - while (pathname[n] == cwd[n] && n < cwdlen) + while (n < cwdlen && pathname[n] == cwd[n]) ++n; return n; diff --git a/tools/perf/util/quote.c b/tools/perf/util/quote.c index c6e5dc0dc82..2726fe40eb5 100644 --- a/tools/perf/util/quote.c +++ b/tools/perf/util/quote.c @@ -318,7 +318,7 @@ char *quote_path_relative(const char *in, int len, strbuf_addch(out, '"'); if (prefix) { int off = 0; - while (prefix[off] && off < len && prefix[off] == in[off]) + while (off < len && prefix[off] && prefix[off] == in[off]) if (prefix[off] == '/') { prefix += off + 1; in += off + 1; -- GitLab From c2718348b41a8e7646516d9af8bb0231c6a44374 Mon Sep 17 00:00:00 2001 From: Doug Thompson Date: Tue, 4 Aug 2009 12:02:20 +0200 Subject: [PATCH 0783/1342] amd64_edac: print debug statements only on error Add forgotten return calls for the successful cases. Signed-off-by: Doug Thompson Signed-off-by: Borislav Petkov --- drivers/edac/amd64_edac.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/edac/amd64_edac.c b/drivers/edac/amd64_edac.c index 5fa924d61b1..e2a10bcba7a 100644 --- a/drivers/edac/amd64_edac.c +++ b/drivers/edac/amd64_edac.c @@ -868,6 +868,8 @@ static void amd64_read_dbam_reg(struct amd64_pvt *pvt) goto err_reg; } + return; + err_reg: debugf0("Error reading F2x%03x.\n", reg); } @@ -2634,6 +2636,8 @@ static void amd64_read_mc_registers(struct amd64_pvt *pvt) amd64_dump_misc_regs(pvt); + return; + err_reg: debugf0("Reading an MC register failed\n"); -- GitLab From 57ca7deb062abf56168d15f000c16e25f88a9cf3 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Anders=20Grafstr=C3=B6m?= Date: Tue, 4 Aug 2009 13:11:47 +0200 Subject: [PATCH 0784/1342] jffs2: Fix return value from jffs2_do_readpage_nolock() MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This fixes "kernel BUG at fs/jffs2/file.c:251!". This pseudocode hopefully illustrates the scenario that triggers it: jffs2_write_begin { jffs2_do_readpage_nolock { jffs2_read_inode_range { jffs2_read_dnode { Data CRC 33c102e9 != calculated CRC 0ef77e7b for node at 005d42e4 return -EIO; } } ClearPageUptodate(pg); return 0; } } jffs2_write_end { BUG_ON(!PageUptodate(pg)); } Signed-off-by: Anders Grafström Signed-off-by: David Woodhouse --- fs/jffs2/file.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/jffs2/file.c b/fs/jffs2/file.c index 5edc2bf2058..23c94753986 100644 --- a/fs/jffs2/file.c +++ b/fs/jffs2/file.c @@ -99,7 +99,7 @@ static int jffs2_do_readpage_nolock (struct inode *inode, struct page *pg) kunmap(pg); D2(printk(KERN_DEBUG "readpage finished\n")); - return 0; + return ret; } int jffs2_do_readpage_unlock(struct inode *inode, struct page *pg) -- GitLab From 6c7184b77464261b7d55583a48accbd1350923a3 Mon Sep 17 00:00:00 2001 From: Jack Steiner Date: Mon, 27 Jul 2009 09:35:07 -0500 Subject: [PATCH 0785/1342] x86, UV: Handle missing blade-local memory correctly UV blades may not have any blade-local memory. Add a field (nid) to the UV blade structure to indicates whether the node has local memory. This is needed by the GRU driver (pushed separately). Signed-off-by: Jack Steiner Cc: linux-mm@kvack.org LKML-Reference: <20090727143507.GA7006@sgi.com> Signed-off-by: Ingo Molnar --- arch/x86/include/asm/uv/uv_hub.h | 7 +++++++ arch/x86/kernel/apic/x2apic_uv_x.c | 5 +++++ 2 files changed, 12 insertions(+) diff --git a/arch/x86/include/asm/uv/uv_hub.h b/arch/x86/include/asm/uv/uv_hub.h index 341070f7ad5..a6dde059e02 100644 --- a/arch/x86/include/asm/uv/uv_hub.h +++ b/arch/x86/include/asm/uv/uv_hub.h @@ -327,6 +327,7 @@ struct uv_blade_info { unsigned short nr_possible_cpus; unsigned short nr_online_cpus; unsigned short pnode; + short memory_nid; }; extern struct uv_blade_info *uv_blade_info; extern short *uv_node_to_blade; @@ -363,6 +364,12 @@ static inline int uv_blade_to_pnode(int bid) return uv_blade_info[bid].pnode; } +/* Nid of memory node on blade. -1 if no blade-local memory */ +static inline int uv_blade_to_memory_nid(int bid) +{ + return uv_blade_info[bid].memory_nid; +} + /* Determine the number of possible cpus on a blade */ static inline int uv_blade_nr_possible_cpus(int bid) { diff --git a/arch/x86/kernel/apic/x2apic_uv_x.c b/arch/x86/kernel/apic/x2apic_uv_x.c index 096d19aea2f..ad3f0a984ca 100644 --- a/arch/x86/kernel/apic/x2apic_uv_x.c +++ b/arch/x86/kernel/apic/x2apic_uv_x.c @@ -591,6 +591,8 @@ void __init uv_system_init(void) bytes = sizeof(struct uv_blade_info) * uv_num_possible_blades(); uv_blade_info = kmalloc(bytes, GFP_KERNEL); BUG_ON(!uv_blade_info); + for (blade = 0; blade < uv_num_possible_blades(); blade++) + uv_blade_info[blade].memory_nid = -1; get_lowmem_redirect(&lowmem_redir_base, &lowmem_redir_size); @@ -629,6 +631,9 @@ void __init uv_system_init(void) lcpu = uv_blade_info[blade].nr_possible_cpus; uv_blade_info[blade].nr_possible_cpus++; + /* Any node on the blade, else will contain -1. */ + uv_blade_info[blade].memory_nid = nid; + uv_cpu_hub_info(cpu)->lowmem_remap_base = lowmem_redir_base; uv_cpu_hub_info(cpu)->lowmem_remap_top = lowmem_redir_size; uv_cpu_hub_info(cpu)->m_val = m_val; -- GitLab From cc5e4fa1bd4d2f56da07f9092281afdcd2374ab9 Mon Sep 17 00:00:00 2001 From: Jack Steiner Date: Mon, 27 Jul 2009 09:36:56 -0500 Subject: [PATCH 0786/1342] x86, UV: Delete mapping of MMR rangs mapped by BIOS The UV BIOS has added additional MMR ranges that are mapped via EFI virtual mode mappings. These ranges should be deleted from ranges mapped by uv_system_init(). Signed-off-by: Jack Steiner Cc: linux-mm@kvack.org LKML-Reference: <20090727143656.GA7698@sgi.com> Signed-off-by: Ingo Molnar --- arch/x86/kernel/apic/x2apic_uv_x.c | 31 +----------------------------- 1 file changed, 1 insertion(+), 30 deletions(-) diff --git a/arch/x86/kernel/apic/x2apic_uv_x.c b/arch/x86/kernel/apic/x2apic_uv_x.c index ad3f0a984ca..445c210daf8 100644 --- a/arch/x86/kernel/apic/x2apic_uv_x.c +++ b/arch/x86/kernel/apic/x2apic_uv_x.c @@ -362,12 +362,6 @@ static __init void get_lowmem_redirect(unsigned long *base, unsigned long *size) BUG(); } -static __init void map_low_mmrs(void) -{ - init_extra_mapping_uc(UV_GLOBAL_MMR32_BASE, UV_GLOBAL_MMR32_SIZE); - init_extra_mapping_uc(UV_LOCAL_MMR_BASE, UV_LOCAL_MMR_SIZE); -} - enum map_type {map_wb, map_uc}; static __init void map_high(char *id, unsigned long base, int shift, @@ -395,26 +389,6 @@ static __init void map_gru_high(int max_pnode) map_high("GRU", gru.s.base, shift, max_pnode, map_wb); } -static __init void map_config_high(int max_pnode) -{ - union uvh_rh_gam_cfg_overlay_config_mmr_u cfg; - int shift = UVH_RH_GAM_CFG_OVERLAY_CONFIG_MMR_BASE_SHFT; - - cfg.v = uv_read_local_mmr(UVH_RH_GAM_CFG_OVERLAY_CONFIG_MMR); - if (cfg.s.enable) - map_high("CONFIG", cfg.s.base, shift, max_pnode, map_uc); -} - -static __init void map_mmr_high(int max_pnode) -{ - union uvh_rh_gam_mmr_overlay_config_mmr_u mmr; - int shift = UVH_RH_GAM_MMR_OVERLAY_CONFIG_MMR_BASE_SHFT; - - mmr.v = uv_read_local_mmr(UVH_RH_GAM_MMR_OVERLAY_CONFIG_MMR); - if (mmr.s.enable) - map_high("MMR", mmr.s.base, shift, max_pnode, map_uc); -} - static __init void map_mmioh_high(int max_pnode) { union uvh_rh_gam_mmioh_overlay_config_mmr_u mmioh; @@ -566,8 +540,6 @@ void __init uv_system_init(void) unsigned long mmr_base, present, paddr; unsigned short pnode_mask; - map_low_mmrs(); - m_n_config.v = uv_read_local_mmr(UVH_SI_ADDR_MAP_CONFIG); m_val = m_n_config.s.m_skt; n_val = m_n_config.s.n_skt; @@ -667,11 +639,10 @@ void __init uv_system_init(void) pnode = (paddr >> m_val) & pnode_mask; blade = boot_pnode_to_blade(pnode); uv_node_to_blade[nid] = blade; + max_pnode = max(pnode, max_pnode); } map_gru_high(max_pnode); - map_mmr_high(max_pnode); - map_config_high(max_pnode); map_mmioh_high(max_pnode); uv_cpu_init(); -- GitLab From 67e83f309ed0baaf01a2c956b5174905bcdc1242 Mon Sep 17 00:00:00 2001 From: Jack Steiner Date: Mon, 27 Jul 2009 09:38:08 -0500 Subject: [PATCH 0787/1342] x86, UV: Fix macros for accessing large node numbers The UV chipset automatically supplies the upper bits on nodes being referenced by MMR accesses. These bit can be deleted from the hub addressing macros. Signed-off-by: Jack Steiner LKML-Reference: <20090727143808.GA8076@sgi.com> Signed-off-by: Ingo Molnar --- arch/x86/include/asm/uv/uv_hub.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/include/asm/uv/uv_hub.h b/arch/x86/include/asm/uv/uv_hub.h index a6dde059e02..77a68505419 100644 --- a/arch/x86/include/asm/uv/uv_hub.h +++ b/arch/x86/include/asm/uv/uv_hub.h @@ -175,7 +175,7 @@ DECLARE_PER_CPU(struct uv_hub_info_s, __uv_hub_info); #define UV_GLOBAL_MMR32_PNODE_BITS(p) ((p) << (UV_GLOBAL_MMR32_PNODE_SHIFT)) #define UV_GLOBAL_MMR64_PNODE_BITS(p) \ - ((unsigned long)(UV_PNODE_TO_GNODE(p)) << UV_GLOBAL_MMR64_PNODE_SHIFT) + (((unsigned long)(p)) << UV_GLOBAL_MMR64_PNODE_SHIFT) #define UV_APIC_PNODE_SHIFT 6 -- GitLab From c5997fa8d7aca3c9876a6ff71bacf27c41095ce9 Mon Sep 17 00:00:00 2001 From: Jack Steiner Date: Mon, 27 Jul 2009 09:38:56 -0500 Subject: [PATCH 0788/1342] x86, UV: Fix UV apic mode Change SGI UV default apicid mode to "physical". This is required to match settings in the UV hub chip. Signed-off-by: Jack Steiner LKML-Reference: <20090727143856.GA8905@sgi.com> Signed-off-by: Ingo Molnar --- arch/x86/kernel/apic/x2apic_uv_x.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/apic/x2apic_uv_x.c b/arch/x86/kernel/apic/x2apic_uv_x.c index 445c210daf8..832e908adcb 100644 --- a/arch/x86/kernel/apic/x2apic_uv_x.c +++ b/arch/x86/kernel/apic/x2apic_uv_x.c @@ -261,7 +261,7 @@ struct apic apic_x2apic_uv_x = { .apic_id_registered = uv_apic_id_registered, .irq_delivery_mode = dest_Fixed, - .irq_dest_mode = 1, /* logical */ + .irq_dest_mode = 0, /* physical */ .target_cpus = uv_target_cpus, .disable_esr = 0, -- GitLab From d8c7eb34c2db6268909ae8c3958be63bde254292 Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Sat, 25 Jul 2009 03:23:09 -0700 Subject: [PATCH 0789/1342] x86: Don't use current_cpu_data in x2apic phys_pkg_id One system has socket 1 come up as BSP. kexeced kernel reports BSP as: [ 1.524550] Initializing cgroup subsys cpuacct [ 1.536064] initial_apicid:20 [ 1.537135] ht_mask_width:1 [ 1.538128] core_select_mask:f [ 1.539126] core_plus_mask_width:5 [ 1.558479] CPU: Physical Processor ID: 0 [ 1.559501] CPU: Processor Core ID: 0 [ 1.560539] CPU: L1 I cache: 32K, L1 D cache: 32K [ 1.579098] CPU: L2 cache: 256K [ 1.580085] CPU: L3 cache: 24576K [ 1.581108] CPU 0/0x20 -> Node 0 [ 1.596193] CPU 0 microcode level: 0xffff0008 It doesn't have correct physical processor id and will get an error: [ 38.840859] CPU0 attaching sched-domain: [ 38.848287] domain 0: span 0,8,72 level SIBLING [ 38.851151] groups: 0 8 72 [ 38.858137] domain 1: span 0,8-15,72-79 level MC [ 38.868944] groups: 0,8,72 9,73 10,74 11,75 12,76 13,77 14,78 15,79 [ 38.881383] ERROR: parent span is not a superset of domain->span [ 38.890724] domain 2: span 0-7,64-71 level CPU [ 38.899237] ERROR: domain->groups does not contain CPU0 [ 38.909229] groups: 8-15,72-79 [ 38.912547] ERROR: groups don't span domain->span [ 38.919665] domain 3: span 0-127 level NODE [ 38.930739] groups: 0-7,64-71 8-15,72-79 16-23,80-87 24-31,88-95 32-39,96-103 40-47,104-111 48-55,112-119 56-63,120-127 it turns out: we can not use current_cpu_data in phys_pgd_id for x2apic. identify_boot_cpu() is called by check_bugs() before smp_prepare_cpus() and till smp_prepare_cpus() current_cpu_data for bsp is assigned with boot_cpu_data. Just make phys_pkg_id for x2apic is aligned to xapic. Signed-off-by: Yinghai Lu Acked-by: Suresh Siddha Cc: Andrew Morton LKML-Reference: <4A6ADD0D.10002@kernel.org> Signed-off-by: Ingo Molnar --- arch/x86/kernel/apic/x2apic_cluster.c | 2 +- arch/x86/kernel/apic/x2apic_phys.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/x86/kernel/apic/x2apic_cluster.c b/arch/x86/kernel/apic/x2apic_cluster.c index 8e4cbb255c3..2ed4e2bb3b3 100644 --- a/arch/x86/kernel/apic/x2apic_cluster.c +++ b/arch/x86/kernel/apic/x2apic_cluster.c @@ -170,7 +170,7 @@ static unsigned long set_apic_id(unsigned int id) static int x2apic_cluster_phys_pkg_id(int initial_apicid, int index_msb) { - return current_cpu_data.initial_apicid >> index_msb; + return initial_apicid >> index_msb; } static void x2apic_send_IPI_self(int vector) diff --git a/arch/x86/kernel/apic/x2apic_phys.c b/arch/x86/kernel/apic/x2apic_phys.c index a284359627e..0b631c6a2e0 100644 --- a/arch/x86/kernel/apic/x2apic_phys.c +++ b/arch/x86/kernel/apic/x2apic_phys.c @@ -162,7 +162,7 @@ static unsigned long set_apic_id(unsigned int id) static int x2apic_phys_pkg_id(int initial_apicid, int index_msb) { - return current_cpu_data.initial_apicid >> index_msb; + return initial_apicid >> index_msb; } static void x2apic_send_IPI_self(int vector) -- GitLab From 6abf65510944d33b47575d151c6b318993c8d2b5 Mon Sep 17 00:00:00 2001 From: Jan Beulich Date: Thu, 30 Jul 2009 16:49:30 +0100 Subject: [PATCH 0790/1342] x86, 32-bit: Fix double accounting in reserve_top_address() With VMALLOC_END included in the calculation of MAXMEM (as of 2.6.28) it is no longer correct to also bump __VMALLOC_RESERVE in reserve_top_address(). Doing so results in needlessly small lowmem. Signed-off-by: Jan Beulich LKML-Reference: <4A71DD2A020000780000D482@vpn.id2.novell.com> Signed-off-by: Ingo Molnar --- arch/x86/mm/pgtable.c | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/x86/mm/pgtable.c b/arch/x86/mm/pgtable.c index af8f9650058..ed34f5e3599 100644 --- a/arch/x86/mm/pgtable.c +++ b/arch/x86/mm/pgtable.c @@ -329,7 +329,6 @@ void __init reserve_top_address(unsigned long reserve) printk(KERN_INFO "Reserving virtual address space above 0x%08x\n", (int)-reserve); __FIXADDR_TOP = -reserve - PAGE_SIZE; - __VMALLOC_RESERVE += reserve; #endif } -- GitLab From 2a5ef41661b56cf4eee042a6967c4e14b63e8eac Mon Sep 17 00:00:00 2001 From: Jack Steiner Date: Mon, 20 Jul 2009 09:28:41 -0500 Subject: [PATCH 0791/1342] x86, UV: Complete IRQ interrupt migration in arch_enable_uv_irq() In uv_setup_irq(), the call to create_irq() initially assigns IRQ vectors to cpu 0. The subsequent call to assign_irq_vector() in arch_enable_uv_irq() migrates the IRQ to another cpu and frees the cpu 0 vector - at least it will be freed as soon as the "IRQ move" completes. arch_enable_uv_irq() needs to send a cleanup IPI to complete the IRQ move. Otherwise, assignment of GRU interrupts on large systems (>200 cpus) will exhaust the cpu 0 interrupt vectors and initialization of the GRU driver will fail. Signed-off-by: Jack Steiner LKML-Reference: <20090720142840.GA8885@sgi.com> Signed-off-by: Ingo Molnar --- arch/x86/kernel/apic/io_apic.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/x86/kernel/apic/io_apic.c b/arch/x86/kernel/apic/io_apic.c index 2284a4812b6..d2ed6c5ddc8 100644 --- a/arch/x86/kernel/apic/io_apic.c +++ b/arch/x86/kernel/apic/io_apic.c @@ -3793,6 +3793,9 @@ int arch_enable_uv_irq(char *irq_name, unsigned int irq, int cpu, int mmr_blade, mmr_pnode = uv_blade_to_pnode(mmr_blade); uv_write_global_mmr64(mmr_pnode, mmr_offset, mmr_value); + if (cfg->move_in_progress) + send_cleanup_vector(cfg); + return irq; } -- GitLab From dc731fbbadf5d65c98fcd6c86472aa286c16458a Mon Sep 17 00:00:00 2001 From: Subrata Modak Date: Tue, 21 Jul 2009 08:02:27 +0530 Subject: [PATCH 0792/1342] x86: Work around compilation warning in arch/x86/kernel/apm_32.c The following fix was initially inspired by David Howells fix few days back: http://lkml.org/lkml/2009/7/9/109 However, Ingo disapproves such fixes as it's dangerous (it can hide future, relevant warnings) - in something as performance-uncritical. So, initialize 'err' to '0' to work around a GCC false positive warning: http://lkml.org/lkml/2009/7/18/89 Signed-off-by: Subrata Modak Cc: Sachin P Sant Cc: David Howells Cc: Balbir Singh Cc: Stephen Rothwell LKML-Reference: <20090721023226.31855.67236.sendpatchset@subratamodak.linux.ibm.com> Signed-off-by: Ingo Molnar --- arch/x86/kernel/apm_32.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/apm_32.c b/arch/x86/kernel/apm_32.c index 79302e9a33a..442b5508893 100644 --- a/arch/x86/kernel/apm_32.c +++ b/arch/x86/kernel/apm_32.c @@ -811,7 +811,7 @@ static int apm_do_idle(void) u8 ret = 0; int idled = 0; int polling; - int err; + int err = 0; polling = !!(current_thread_info()->status & TS_POLLING); if (polling) { -- GitLab From f26542600e605482a1231c44ddb2966d69bd09b0 Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Mon, 29 Jun 2009 10:40:20 +0200 Subject: [PATCH 0793/1342] perf_counter: Set the CONFIG_PERF_COUNTERS default to y if CONFIG_PROFILING=y If user has already enabled profiling support in the kernel (for oprofile, old-style profiling of ftrace) then offer up perfcounters with a y default in interactive kconfig sessions. Still keep it off by default otherwise. Cc: Peter Zijlstra Cc: Linus Torvalds Signed-off-by: Ingo Molnar --- init/Kconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/init/Kconfig b/init/Kconfig index 823ee0a2d2a..3f7e60995c8 100644 --- a/init/Kconfig +++ b/init/Kconfig @@ -940,6 +940,7 @@ menu "Performance Counters" config PERF_COUNTERS bool "Kernel Performance Counters" + default y if PROFILING depends on HAVE_PERF_COUNTERS select ANON_INODES help -- GitLab From 1cef8e41073efe47e809f49670eb461307e52ccc Mon Sep 17 00:00:00 2001 From: Russell King Date: Mon, 27 Jul 2009 11:30:48 +0530 Subject: [PATCH 0794/1342] mfd: twl4030 irq fixes The TWL4030 IRQ handler has a bug which leads to spinlock lock-up. It is calling the 'unmask' function in a process context. :The mask/unmask/ack functions are only designed to be called from the IRQ handler code, or the proper API interfaces found in linux/interrupt.h. Also there is no need to have IRQ chaining mechanism. The right way to handle this is to claim the parent interrupt as a standard interrupt and arrange for handle_twl4030_pih to take care of the rest of the devices. Mail thread on this issue can be found at: http://marc.info/?l=linux-arm-kernel&m=124629940123396&w=2 Signed-off-by: Russell King Tested-by: Santosh Shilimkar Acked-by: Tony Lindgren Signed-off-by: Samuel Ortiz --- drivers/mfd/twl4030-irq.c | 55 +++++++++++++++++---------------------- 1 file changed, 24 insertions(+), 31 deletions(-) diff --git a/drivers/mfd/twl4030-irq.c b/drivers/mfd/twl4030-irq.c index bae61b22501..7d430835655 100644 --- a/drivers/mfd/twl4030-irq.c +++ b/drivers/mfd/twl4030-irq.c @@ -180,14 +180,9 @@ static struct completion irq_event; static int twl4030_irq_thread(void *data) { long irq = (long)data; - struct irq_desc *desc = irq_to_desc(irq); static unsigned i2c_errors; static const unsigned max_i2c_errors = 100; - if (!desc) { - pr_err("twl4030: Invalid IRQ: %ld\n", irq); - return -EINVAL; - } current->flags |= PF_NOFREEZE; @@ -240,7 +235,7 @@ static int twl4030_irq_thread(void *data) } local_irq_enable(); - desc->chip->unmask(irq); + enable_irq(irq); } return 0; @@ -255,25 +250,13 @@ static int twl4030_irq_thread(void *data) * thread. All we do here is acknowledge and mask the interrupt and wakeup * the kernel thread. */ -static void handle_twl4030_pih(unsigned int irq, struct irq_desc *desc) +static irqreturn_t handle_twl4030_pih(int irq, void *devid) { /* Acknowledge, clear *AND* mask the interrupt... */ - desc->chip->ack(irq); - complete(&irq_event); -} - -static struct task_struct *start_twl4030_irq_thread(long irq) -{ - struct task_struct *thread; - - init_completion(&irq_event); - thread = kthread_run(twl4030_irq_thread, (void *)irq, "twl4030-irq"); - if (!thread) - pr_err("twl4030: could not create irq %ld thread!\n", irq); - - return thread; + disable_irq_nosync(irq); + complete(devid); + return IRQ_HANDLED; } - /*----------------------------------------------------------------------*/ /* @@ -734,18 +717,28 @@ int twl_init_irq(int irq_num, unsigned irq_base, unsigned irq_end) } /* install an irq handler to demultiplex the TWL4030 interrupt */ - task = start_twl4030_irq_thread(irq_num); - if (!task) { - pr_err("twl4030: irq thread FAIL\n"); - status = -ESRCH; - goto fail; - } - set_irq_data(irq_num, task); - set_irq_chained_handler(irq_num, handle_twl4030_pih); - return status; + init_completion(&irq_event); + status = request_irq(irq_num, handle_twl4030_pih, IRQF_DISABLED, + "TWL4030-PIH", &irq_event); + if (status < 0) { + pr_err("twl4030: could not claim irq%d: %d\n", irq_num, status); + goto fail_rqirq; + } + + task = kthread_run(twl4030_irq_thread, (void *)irq_num, "twl4030-irq"); + if (IS_ERR(task)) { + pr_err("twl4030: could not create irq %d thread!\n", irq_num); + status = PTR_ERR(task); + goto fail_kthread; + } + return status; +fail_kthread: + free_irq(irq_num, &irq_event); +fail_rqirq: + /* clean up twl4030_sih_setup */ fail: for (i = irq_base; i < irq_end; i++) set_irq_chip_and_handler(i, NULL, NULL); -- GitLab From 26d204afa18f7df177f21bdb3759e0098ca8f7d5 Mon Sep 17 00:00:00 2001 From: "Pallipadi, Venkatesh" Date: Wed, 29 Jul 2009 13:36:10 -0700 Subject: [PATCH 0795/1342] [CPUFREQ] Fix NULL pointer dereference regression in conservative governor Commit ee88415caf736b89500f16e0a545614541a45005 introduced this regression when it removed enable bit in cpu_dbs_info_s. That added a possibility of dbs_cpufreq_notifier getting called for a CPU that is not yet managed by conservative governor. That will happen as the transition notifier is set as soon as one CPU switches to conservative governor and other CPUs can get a NULL pointer dereference without the enable bit check. Add the enable bit back again. Reported-by: Lermytte Christophe Signed-off-by: Venkatesh Pallipadi Signed-off-by: Dave Jones --- drivers/cpufreq/cpufreq_conservative.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/cpufreq/cpufreq_conservative.c b/drivers/cpufreq/cpufreq_conservative.c index 57490502b21..bdea7e2f94b 100644 --- a/drivers/cpufreq/cpufreq_conservative.c +++ b/drivers/cpufreq/cpufreq_conservative.c @@ -63,6 +63,7 @@ struct cpu_dbs_info_s { unsigned int down_skip; unsigned int requested_freq; int cpu; + unsigned int enable:1; /* * percpu mutex that serializes governor limit change with * do_dbs_timer invocation. We do not want do_dbs_timer to run @@ -141,6 +142,9 @@ dbs_cpufreq_notifier(struct notifier_block *nb, unsigned long val, struct cpufreq_policy *policy; + if (!this_dbs_info->enable) + return 0; + policy = this_dbs_info->cur_policy; /* @@ -497,6 +501,7 @@ static inline void dbs_timer_init(struct cpu_dbs_info_s *dbs_info) int delay = usecs_to_jiffies(dbs_tuners_ins.sampling_rate); delay -= jiffies % delay; + dbs_info->enable = 1; INIT_DELAYED_WORK_DEFERRABLE(&dbs_info->work, do_dbs_timer); queue_delayed_work_on(dbs_info->cpu, kconservative_wq, &dbs_info->work, delay); @@ -504,6 +509,7 @@ static inline void dbs_timer_init(struct cpu_dbs_info_s *dbs_info) static inline void dbs_timer_exit(struct cpu_dbs_info_s *dbs_info) { + dbs_info->enable = 0; cancel_delayed_work_sync(&dbs_info->work); } -- GitLab From 42c74b84c64633dd3badbfc2abd2ef1728b64b30 Mon Sep 17 00:00:00 2001 From: Prarit Bhargava Date: Mon, 3 Aug 2009 10:58:11 -0400 Subject: [PATCH 0796/1342] [CPUFREQ] Do not set policy for offline cpus Suspend/Resume fails on multi socket, multi core systems because the cpufreq code erroneously sets the per_cpu policy_cpu value when a logical cpu is offline. This most notably results in missing sysfs files that are used to set the cpu frequencies of the various cpus. Signed-off-by: Prarit Bhargava Signed-off-by: Dave Jones --- drivers/cpufreq/cpufreq.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/cpufreq/cpufreq.c b/drivers/cpufreq/cpufreq.c index b90eda8b344..120d236c0ff 100644 --- a/drivers/cpufreq/cpufreq.c +++ b/drivers/cpufreq/cpufreq.c @@ -924,6 +924,8 @@ static int cpufreq_add_dev(struct sys_device *sys_dev) spin_lock_irqsave(&cpufreq_driver_lock, flags); for_each_cpu(j, policy->cpus) { + if (!cpu_online(j)) + continue; per_cpu(cpufreq_cpu_data, j) = policy; per_cpu(policy_cpu, j) = policy->cpu; } -- GitLab From d5194decd0a6f792b2789eebd4ddf022a248f655 Mon Sep 17 00:00:00 2001 From: Thomas Renninger Date: Wed, 29 Jul 2009 11:26:20 +0200 Subject: [PATCH 0797/1342] [CPUFREQ] Fix a kobject reference bug related to managed CPUs The first offline/online cycle is successful, the second not. Doing: echo 0 >cpu1/online echo 1 >cpu1/online echo 0 >cpu1/online The last command will trigger: Jul 22 14:39:50 linux kernel: [ 593.210125] ------------[ cut here ]------------ Jul 22 14:39:50 linux kernel: [ 593.210139] WARNING: at lib/kref.c:43 kref_get+0x23/0x2b() Jul 22 14:39:50 linux kernel: [ 593.210144] Hardware name: To Be Filled By O.E.M. Jul 22 14:39:50 linux kernel: [ 593.210148] Modules linked in: powernow_k8 Jul 22 14:39:50 linux kernel: [ 593.210158] Pid: 378, comm: kondemand/2 Tainted: G W 2.6.31-rc2 #38 Jul 22 14:39:50 linux kernel: [ 593.210163] Call Trace: Jul 22 14:39:50 linux kernel: [ 593.210171] [] ? kref_get+0x23/0x2b Jul 22 14:39:50 linux kernel: [ 593.210181] [] warn_slowpath_common+0x77/0xa4 Jul 22 14:39:50 linux kernel: [ 593.210190] [] warn_slowpath_null+0xf/0x11 Jul 22 14:39:50 linux kernel: [ 593.210198] [] kref_get+0x23/0x2b Jul 22 14:39:50 linux kernel: [ 593.210206] [] kobject_get+0x1a/0x22 Jul 22 14:39:50 linux kernel: [ 593.210214] [] cpufreq_cpu_get+0x8a/0xcb Jul 22 14:39:50 linux kernel: [ 593.210222] [] __cpufreq_driver_getavg+0x1d/0x67 Jul 22 14:39:50 linux kernel: [ 593.210231] [] do_dbs_timer+0x158/0x27f Jul 22 14:39:50 linux kernel: [ 593.210240] [] worker_thread+0x200/0x313 ... The output continues on every do_dbs_timer ondemand freq checking poll. This regression was introduced by git commit: 3f4a782b5ce2698b1870b5a7b573cd721d4fce33 The policy is released when the cpufreq device is removed in: __cpufreq_remove_dev(): /* if this isn't the CPU which is the parent of the kobj, we * only need to unlink, put and exit */ Not creating the symlink is not sever at all. As long as: sysfs_remove_link(&sys_dev->kobj, "cpufreq"); handles it gracefully that the symlink did not exist. Possibly no error should be returned at all, because ondemand governor would still provide the same functionality. Userspace in userspace gov case might be confused if the link is missing. Resolves http://bugzilla.kernel.org/show_bug.cgi?id=13903 CC: Mathieu Desnoyers CC: Venkatesh Pallipadi Signed-off-by: Thomas Renninger Signed-off-by: Dave Jones --- drivers/cpufreq/cpufreq.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/cpufreq/cpufreq.c b/drivers/cpufreq/cpufreq.c index 120d236c0ff..bd74a0b1217 100644 --- a/drivers/cpufreq/cpufreq.c +++ b/drivers/cpufreq/cpufreq.c @@ -858,6 +858,8 @@ static int cpufreq_add_dev(struct sys_device *sys_dev) /* Check for existing affected CPUs. * They may not be aware of it due to CPU Hotplug. + * cpufreq_cpu_put is called when the device is removed + * in __cpufreq_remove_dev() */ managed_policy = cpufreq_cpu_get(j); if (unlikely(managed_policy)) { @@ -884,7 +886,7 @@ static int cpufreq_add_dev(struct sys_device *sys_dev) ret = sysfs_create_link(&sys_dev->kobj, &managed_policy->kobj, "cpufreq"); - if (!ret) + if (ret) cpufreq_cpu_put(managed_policy); /* * Success. We only needed to be added to the mask. -- GitLab From 4bc5d34135039566b8d6efa2de7515b2be505da8 Mon Sep 17 00:00:00 2001 From: Dave Jones Date: Tue, 4 Aug 2009 14:03:25 -0400 Subject: [PATCH 0798/1342] [CPUFREQ] Make cpufreq suspend code conditional on powerpc. The suspend code runs with interrupts disabled, and the powerpc workaround we do in the cpufreq suspend hook calls the drivers ->get method. powernow-k8's ->get does an smp_call_function_single which needs interrupts enabled cpufreq's suspend/resume code was added in 42d4dc3f4e1e to work around a hardware problem on ppc powerbooks. If we make all this code conditional on powerpc, we avoid the issue above. Signed-off-by: Dave Jones --- drivers/cpufreq/cpufreq.c | 21 +++++++++++++++++++-- 1 file changed, 19 insertions(+), 2 deletions(-) diff --git a/drivers/cpufreq/cpufreq.c b/drivers/cpufreq/cpufreq.c index bd74a0b1217..fd69086d08d 100644 --- a/drivers/cpufreq/cpufreq.c +++ b/drivers/cpufreq/cpufreq.c @@ -1248,13 +1248,22 @@ EXPORT_SYMBOL(cpufreq_get); static int cpufreq_suspend(struct sys_device *sysdev, pm_message_t pmsg) { - int cpu = sysdev->id; int ret = 0; + +#ifdef __powerpc__ + int cpu = sysdev->id; unsigned int cur_freq = 0; struct cpufreq_policy *cpu_policy; dprintk("suspending cpu %u\n", cpu); + /* + * This whole bogosity is here because Powerbooks are made of fail. + * No sane platform should need any of the code below to be run. + * (it's entirely the wrong thing to do, as driver->get may + * reenable interrupts on some architectures). + */ + if (!cpu_online(cpu)) return 0; @@ -1313,6 +1322,7 @@ static int cpufreq_suspend(struct sys_device *sysdev, pm_message_t pmsg) out: cpufreq_cpu_put(cpu_policy); +#endif /* __powerpc__ */ return ret; } @@ -1326,12 +1336,18 @@ out: */ static int cpufreq_resume(struct sys_device *sysdev) { - int cpu = sysdev->id; int ret = 0; + +#ifdef __powerpc__ + int cpu = sysdev->id; struct cpufreq_policy *cpu_policy; dprintk("resuming cpu %u\n", cpu); + /* As with the ->suspend method, all the code below is + * only necessary because Powerbooks suck. + * See commit 42d4dc3f4e1e for jokes. */ + if (!cpu_online(cpu)) return 0; @@ -1395,6 +1411,7 @@ out: schedule_work(&cpu_policy->update); fail: cpufreq_cpu_put(cpu_policy); +#endif /* __powerpc__ */ return ret; } -- GitLab From e0cff5ed27acd355264b210d9622da801a431e19 Mon Sep 17 00:00:00 2001 From: Alexander Duyck Date: Tue, 4 Aug 2009 11:46:41 -0700 Subject: [PATCH 0799/1342] igbvf: Allow VF driver to correctly recognize failure to set mac The VF driver was not correctly recognizing that it did not correctly set it's mac address. As a result the VF driver was unable to receive network traffic until being unloaded and reloaded. The issue was root caused to the fact that the CTS bit was not taken into account when checking for the request being NAKed. Signed-off-by: Alexander Duyck Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/igbvf/vf.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/net/igbvf/vf.c b/drivers/net/igbvf/vf.c index 2a4faf9ade6..a9a61efa964 100644 --- a/drivers/net/igbvf/vf.c +++ b/drivers/net/igbvf/vf.c @@ -274,6 +274,8 @@ static s32 e1000_set_vfta_vf(struct e1000_hw *hw, u16 vid, bool set) err = mbx->ops.read_posted(hw, msgbuf, 2); + msgbuf[0] &= ~E1000_VT_MSGTYPE_CTS; + /* if nacked the vlan was rejected */ if (!err && (msgbuf[0] == (E1000_VF_SET_VLAN | E1000_VT_MSGTYPE_NACK))) err = -E1000_ERR_MAC_INIT; @@ -317,6 +319,8 @@ static void e1000_rar_set_vf(struct e1000_hw *hw, u8 * addr, u32 index) if (!ret_val) ret_val = mbx->ops.read_posted(hw, msgbuf, 3); + msgbuf[0] &= ~E1000_VT_MSGTYPE_CTS; + /* if nacked the address was rejected, use "perm_addr" */ if (!ret_val && (msgbuf[0] == (E1000_VF_SET_MAC_ADDR | E1000_VT_MSGTYPE_NACK))) -- GitLab From 357eb46d8f275b4e8484541234ea3ba06065e258 Mon Sep 17 00:00:00 2001 From: Hannes Hering Date: Tue, 4 Aug 2009 11:48:39 -0700 Subject: [PATCH 0800/1342] ehea: Fix napi list corruption on ifconfig down This patch fixes the napi list handling when an ehea interface is shut down to avoid corruption of the napi list. Signed-off-by: Hannes Hering Signed-off-by: David S. Miller --- drivers/net/ehea/ehea.h | 2 +- drivers/net/ehea/ehea_main.c | 3 +++ 2 files changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/net/ehea/ehea.h b/drivers/net/ehea/ehea.h index 78952f8324e..fa311a95099 100644 --- a/drivers/net/ehea/ehea.h +++ b/drivers/net/ehea/ehea.h @@ -40,7 +40,7 @@ #include #define DRV_NAME "ehea" -#define DRV_VERSION "EHEA_0101" +#define DRV_VERSION "EHEA_0102" /* eHEA capability flags */ #define DLPAR_PORT_ADD_REM 1 diff --git a/drivers/net/ehea/ehea_main.c b/drivers/net/ehea/ehea_main.c index e8d46cc1bec..977c3d35827 100644 --- a/drivers/net/ehea/ehea_main.c +++ b/drivers/net/ehea/ehea_main.c @@ -1545,6 +1545,9 @@ static int ehea_clean_portres(struct ehea_port *port, struct ehea_port_res *pr) { int ret, i; + if (pr->qp) + netif_napi_del(&pr->napi); + ret = ehea_destroy_qp(pr->qp); if (!ret) { -- GitLab From 14d9fa352592582e457cf75022202766baac1348 Mon Sep 17 00:00:00 2001 From: John Stoffel Date: Tue, 4 Aug 2009 22:10:17 +0200 Subject: [PATCH 0801/1342] Make SCSI SG v4 driver enabled by default and remove EXPERIMENTAL dependency, since udev depends on BSG Make Block Layer SG support v4 the default, since recent udev versions depend on this to access serial numbers and other low level info properly. This should be backported to older kernels as well, since most distros have enabled this for a long time. Signed-off-by: John Stoffel Cc: stable@kernel.org Signed-off-by: Jens Axboe --- block/Kconfig | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-) diff --git a/block/Kconfig b/block/Kconfig index 95a86adc33a..9be0b56eaee 100644 --- a/block/Kconfig +++ b/block/Kconfig @@ -48,9 +48,9 @@ config LBDAF If unsure, say Y. config BLK_DEV_BSG - bool "Block layer SG support v4 (EXPERIMENTAL)" - depends on EXPERIMENTAL - ---help--- + bool "Block layer SG support v4" + default y + help Saying Y here will enable generic SG (SCSI generic) v4 support for any block device. @@ -60,7 +60,10 @@ config BLK_DEV_BSG protocols (e.g. Task Management Functions and SMP in Serial Attached SCSI). - If unsure, say N. + This option is required by recent UDEV versions to properly + access device serial numbers, etc. + + If unsure, say Y. config BLK_DEV_INTEGRITY bool "Block layer data integrity support" -- GitLab From 18eac1cc100fa2afd5f39085aae6b694e417734b Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Mon, 3 Aug 2009 10:58:29 -0700 Subject: [PATCH 0802/1342] tty-ldisc: make refcount be atomic_t 'users' count This is pure preparation of changing the ldisc reference counting to be a true refcount that defines the lifetime of the ldisc. But this is a purely syntactic change for now to make the next steps easier. This patch should make no semantic changes at all. But I wanted to make the ldisc refcount be an atomic (I will be touching it without locks soon enough), and I wanted to rename it so that there isn't quite as much confusion between 'ldo->refcount' (ldisk operations refcount) and 'ld->refcount' (ldisc refcount itself) in the same file. So it's now an atomic 'ld->users' count. It still starts at zero, despite having a reference from 'tty->ldisc', but that will change once we turn it into a _real_ refcount. Signed-off-by: Linus Torvalds Tested-by: OGAWA Hirofumi Tested-by: Sergey Senozhatsky Acked-by: Alan Cox Signed-off-by: Greg Kroah-Hartman --- drivers/char/tty_ldisc.c | 18 ++++++++---------- include/linux/tty_ldisc.h | 2 +- 2 files changed, 9 insertions(+), 11 deletions(-) diff --git a/drivers/char/tty_ldisc.c b/drivers/char/tty_ldisc.c index acd76b767d4..fd175e60aad 100644 --- a/drivers/char/tty_ldisc.c +++ b/drivers/char/tty_ldisc.c @@ -142,7 +142,7 @@ static struct tty_ldisc *tty_ldisc_try_get(int disc) /* lock it */ ldops->refcount++; ld->ops = ldops; - ld->refcount = 0; + atomic_set(&ld->users, 0); err = 0; } } @@ -206,7 +206,7 @@ static void tty_ldisc_put(struct tty_ldisc *ld) ldo->refcount--; module_put(ldo->owner); spin_unlock_irqrestore(&tty_ldisc_lock, flags); - WARN_ON(ld->refcount); + WARN_ON(atomic_read(&ld->users)); kfree(ld); } @@ -297,7 +297,7 @@ static int tty_ldisc_try(struct tty_struct *tty) spin_lock_irqsave(&tty_ldisc_lock, flags); ld = tty->ldisc; if (test_bit(TTY_LDISC, &tty->flags)) { - ld->refcount++; + atomic_inc(&ld->users); ret = 1; } spin_unlock_irqrestore(&tty_ldisc_lock, flags); @@ -324,7 +324,7 @@ struct tty_ldisc *tty_ldisc_ref_wait(struct tty_struct *tty) { /* wait_event is a macro */ wait_event(tty_ldisc_wait, tty_ldisc_try(tty)); - WARN_ON(tty->ldisc->refcount == 0); + WARN_ON(atomic_read(&tty->ldisc->users) == 0); return tty->ldisc; } EXPORT_SYMBOL_GPL(tty_ldisc_ref_wait); @@ -365,11 +365,9 @@ void tty_ldisc_deref(struct tty_ldisc *ld) BUG_ON(ld == NULL); spin_lock_irqsave(&tty_ldisc_lock, flags); - if (ld->refcount == 0) + if (atomic_read(&ld->users) == 0) printk(KERN_ERR "tty_ldisc_deref: no references.\n"); - else - ld->refcount--; - if (ld->refcount == 0) + else if (atomic_dec_and_test(&ld->users)) wake_up(&tty_ldisc_wait); spin_unlock_irqrestore(&tty_ldisc_lock, flags); } @@ -536,10 +534,10 @@ static int tty_ldisc_wait_idle(struct tty_struct *tty) { unsigned long flags; spin_lock_irqsave(&tty_ldisc_lock, flags); - while (tty->ldisc->refcount) { + while (atomic_read(&tty->ldisc->users)) { spin_unlock_irqrestore(&tty_ldisc_lock, flags); if (wait_event_timeout(tty_ldisc_wait, - tty->ldisc->refcount == 0, 5 * HZ) == 0) + atomic_read(&tty->ldisc->users) == 0, 5 * HZ) == 0) return -EBUSY; spin_lock_irqsave(&tty_ldisc_lock, flags); } diff --git a/include/linux/tty_ldisc.h b/include/linux/tty_ldisc.h index 40f38d89677..0c4ee9b88f8 100644 --- a/include/linux/tty_ldisc.h +++ b/include/linux/tty_ldisc.h @@ -144,7 +144,7 @@ struct tty_ldisc_ops { struct tty_ldisc { struct tty_ldisc_ops *ops; - int refcount; + atomic_t users; }; #define TTY_LDISC_MAGIC 0x5403 -- GitLab From 65b770468e98941e45e19780dff9283e663e6b8b Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Mon, 3 Aug 2009 11:11:19 -0700 Subject: [PATCH 0803/1342] tty-ldisc: turn ldisc user count into a proper refcount By using the user count for the actual lifetime rules, we can get rid of the silly "wait_for_idle" logic, because any busy ldisc will automatically stay around until the last user releases it. This avoids a host of odd issues, and simplifies the code. So now, when the last ldisc reference is dropped, we just release the ldisc operations struct reference, and free the ldisc. It looks obvious enough, and it does work for me, but the counting _could_ be off. It probably isn't (bad counting in the new version would generally imply that the old code did something really bad, like free an ldisc with a non-zero count), but it does need some testing, and preferably somebody looking at it. With this change, both 'tty_ldisc_put()' and 'tty_ldisc_deref()' are just aliases for the new ref-counting 'put_ldisc()'. Both of them decrement the ldisc user count and free it if it goes down to zero. They're identical functions, in other words. But the reason they still exist as sepate functions is that one of them was exported (tty_ldisc_deref) and had a stupid name (so I don't want to use it as the main name), and the other one was used in multiple places (and I didn't want to make the patch larger just to rename the users). In addition to the refcounting, I did do some minimal cleanup. For example, now "tty_ldisc_try()" actually returns the ldisc it got under the lock, rather than returning true/false and then the caller would look up the ldisc again (now without the protection of the lock). That said, there's tons of dubious use of 'tty->ldisc' without obviously proper locking or refcounting left. I expressly did _not_ want to try to fix it all, keeping the patch minimal. There may or may not be bugs in that kind of code, but they wouldn't be _new_ bugs. That said, even if the bugs aren't new, the timing and lifetime will change. For example, some silly code may depend on the 'tty->ldisc' pointer not changing because they hold a refcount on the 'ldisc'. And that's no longer true - if you hold a ref on the ldisc, the 'ldisc' itself is safe, but tty->ldisc may change. So the proper locking (remains) to hold tty->ldisc_mutex if you expect tty->ldisc to be stable. That's not really a _new_ rule, but it's an example of something that the old code might have unintentionally depended on and hidden bugs. Whatever. The patch _looks_ sensible to me. The only users of ldisc->users are: - get_ldisc() - atomically increment the count - put_ldisc() - atomically decrements the count and releases if zero - tty_ldisc_try_get() - creates the ldisc, and sets the count to 1. The ldisc should then either be released, or be attached to a tty. Signed-off-by: Linus Torvalds Tested-by: OGAWA Hirofumi Tested-by: Sergey Senozhatsky Acked-by: Alan Cox Signed-off-by: Greg Kroah-Hartman --- drivers/char/tty_ldisc.c | 143 +++++++++++++-------------------------- 1 file changed, 46 insertions(+), 97 deletions(-) diff --git a/drivers/char/tty_ldisc.c b/drivers/char/tty_ldisc.c index fd175e60aad..be55dfcf59a 100644 --- a/drivers/char/tty_ldisc.c +++ b/drivers/char/tty_ldisc.c @@ -48,6 +48,34 @@ static DECLARE_WAIT_QUEUE_HEAD(tty_ldisc_wait); /* Line disc dispatch table */ static struct tty_ldisc_ops *tty_ldiscs[NR_LDISCS]; +static inline struct tty_ldisc *get_ldisc(struct tty_ldisc *ld) +{ + if (ld) + atomic_inc(&ld->users); + return ld; +} + +static inline void put_ldisc(struct tty_ldisc *ld) +{ + if (WARN_ON_ONCE(!ld)) + return; + + /* + * If this is the last user, free the ldisc, and + * release the ldisc ops. + */ + if (atomic_dec_and_test(&ld->users)) { + unsigned long flags; + struct tty_ldisc_ops *ldo = ld->ops; + + kfree(ld); + spin_lock_irqsave(&tty_ldisc_lock, flags); + ldo->refcount--; + module_put(ldo->owner); + spin_unlock_irqrestore(&tty_ldisc_lock, flags); + } +} + /** * tty_register_ldisc - install a line discipline * @disc: ldisc number @@ -142,7 +170,7 @@ static struct tty_ldisc *tty_ldisc_try_get(int disc) /* lock it */ ldops->refcount++; ld->ops = ldops; - atomic_set(&ld->users, 0); + atomic_set(&ld->users, 1); err = 0; } } @@ -181,35 +209,6 @@ static struct tty_ldisc *tty_ldisc_get(int disc) return ld; } -/** - * tty_ldisc_put - drop ldisc reference - * @ld: ldisc - * - * Drop a reference to a line discipline. Manage refcounts and - * module usage counts. Free the ldisc once the recount hits zero. - * - * Locking: - * takes tty_ldisc_lock to guard against ldisc races - */ - -static void tty_ldisc_put(struct tty_ldisc *ld) -{ - unsigned long flags; - int disc = ld->ops->num; - struct tty_ldisc_ops *ldo; - - BUG_ON(disc < N_TTY || disc >= NR_LDISCS); - - spin_lock_irqsave(&tty_ldisc_lock, flags); - ldo = tty_ldiscs[disc]; - BUG_ON(ldo->refcount == 0); - ldo->refcount--; - module_put(ldo->owner); - spin_unlock_irqrestore(&tty_ldisc_lock, flags); - WARN_ON(atomic_read(&ld->users)); - kfree(ld); -} - static void *tty_ldiscs_seq_start(struct seq_file *m, loff_t *pos) { return (*pos < NR_LDISCS) ? pos : NULL; @@ -234,7 +233,7 @@ static int tty_ldiscs_seq_show(struct seq_file *m, void *v) if (IS_ERR(ld)) return 0; seq_printf(m, "%-10s %2d\n", ld->ops->name ? ld->ops->name : "???", i); - tty_ldisc_put(ld); + put_ldisc(ld); return 0; } @@ -288,20 +287,17 @@ static void tty_ldisc_assign(struct tty_struct *tty, struct tty_ldisc *ld) * Locking: takes tty_ldisc_lock */ -static int tty_ldisc_try(struct tty_struct *tty) +static struct tty_ldisc *tty_ldisc_try(struct tty_struct *tty) { unsigned long flags; struct tty_ldisc *ld; - int ret = 0; spin_lock_irqsave(&tty_ldisc_lock, flags); - ld = tty->ldisc; - if (test_bit(TTY_LDISC, &tty->flags)) { - atomic_inc(&ld->users); - ret = 1; - } + ld = NULL; + if (test_bit(TTY_LDISC, &tty->flags)) + ld = get_ldisc(tty->ldisc); spin_unlock_irqrestore(&tty_ldisc_lock, flags); - return ret; + return ld; } /** @@ -322,10 +318,11 @@ static int tty_ldisc_try(struct tty_struct *tty) struct tty_ldisc *tty_ldisc_ref_wait(struct tty_struct *tty) { + struct tty_ldisc *ld; + /* wait_event is a macro */ - wait_event(tty_ldisc_wait, tty_ldisc_try(tty)); - WARN_ON(atomic_read(&tty->ldisc->users) == 0); - return tty->ldisc; + wait_event(tty_ldisc_wait, (ld = tty_ldisc_try(tty)) != NULL); + return ld; } EXPORT_SYMBOL_GPL(tty_ldisc_ref_wait); @@ -342,9 +339,7 @@ EXPORT_SYMBOL_GPL(tty_ldisc_ref_wait); struct tty_ldisc *tty_ldisc_ref(struct tty_struct *tty) { - if (tty_ldisc_try(tty)) - return tty->ldisc; - return NULL; + return tty_ldisc_try(tty); } EXPORT_SYMBOL_GPL(tty_ldisc_ref); @@ -360,19 +355,15 @@ EXPORT_SYMBOL_GPL(tty_ldisc_ref); void tty_ldisc_deref(struct tty_ldisc *ld) { - unsigned long flags; - - BUG_ON(ld == NULL); - - spin_lock_irqsave(&tty_ldisc_lock, flags); - if (atomic_read(&ld->users) == 0) - printk(KERN_ERR "tty_ldisc_deref: no references.\n"); - else if (atomic_dec_and_test(&ld->users)) - wake_up(&tty_ldisc_wait); - spin_unlock_irqrestore(&tty_ldisc_lock, flags); + put_ldisc(ld); } EXPORT_SYMBOL_GPL(tty_ldisc_deref); +static inline void tty_ldisc_put(struct tty_ldisc *ld) +{ + put_ldisc(ld); +} + /** * tty_ldisc_enable - allow ldisc use * @tty: terminal to activate ldisc on @@ -520,31 +511,6 @@ static int tty_ldisc_halt(struct tty_struct *tty) return cancel_delayed_work(&tty->buf.work); } -/** - * tty_ldisc_wait_idle - wait for the ldisc to become idle - * @tty: tty to wait for - * - * Wait for the line discipline to become idle. The discipline must - * have been halted for this to guarantee it remains idle. - * - * tty_ldisc_lock protects the ref counts currently. - */ - -static int tty_ldisc_wait_idle(struct tty_struct *tty) -{ - unsigned long flags; - spin_lock_irqsave(&tty_ldisc_lock, flags); - while (atomic_read(&tty->ldisc->users)) { - spin_unlock_irqrestore(&tty_ldisc_lock, flags); - if (wait_event_timeout(tty_ldisc_wait, - atomic_read(&tty->ldisc->users) == 0, 5 * HZ) == 0) - return -EBUSY; - spin_lock_irqsave(&tty_ldisc_lock, flags); - } - spin_unlock_irqrestore(&tty_ldisc_lock, flags); - return 0; -} - /** * tty_set_ldisc - set line discipline * @tty: the terminal to set @@ -640,14 +606,6 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc) flush_scheduled_work(); - /* Let any existing reference holders finish */ - retval = tty_ldisc_wait_idle(tty); - if (retval < 0) { - clear_bit(TTY_LDISC_CHANGING, &tty->flags); - tty_ldisc_put(new_ldisc); - return retval; - } - mutex_lock(&tty->ldisc_mutex); if (test_bit(TTY_HUPPED, &tty->flags)) { /* We were raced by the hangup method. It will have stomped @@ -793,7 +751,6 @@ void tty_ldisc_hangup(struct tty_struct *tty) if (tty->ldisc) { /* Not yet closed */ /* Switch back to N_TTY */ tty_ldisc_halt(tty); - tty_ldisc_wait_idle(tty); tty_ldisc_reinit(tty); /* At this point we have a closed ldisc and we want to reopen it. We could defer this to the next open but @@ -858,14 +815,6 @@ void tty_ldisc_release(struct tty_struct *tty, struct tty_struct *o_tty) tty_ldisc_halt(tty); flush_scheduled_work(); - /* - * Wait for any short term users (we know they are just driver - * side waiters as the file is closing so user count on the file - * side is zero. - */ - - tty_ldisc_wait_idle(tty); - mutex_lock(&tty->ldisc_mutex); /* * Now kill off the ldisc -- GitLab From cbe9352fa08f90aa03b4dbf1bbabfc95d196e562 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Mon, 3 Aug 2009 14:54:56 -0700 Subject: [PATCH 0804/1342] tty-ldisc: be more careful in 'put_ldisc' locking Use 'atomic_dec_and_lock()' to make sure that we always hold the tty_ldisc_lock when the ldisc count goes to zero. That way we can never race against 'tty_ldisc_try()' increasing the count again. Reported-by: OGAWA Hirofumi Signed-off-by: Linus Torvalds Tested-by: Sergey Senozhatsky Signed-off-by: Greg Kroah-Hartman --- drivers/char/tty_ldisc.c | 17 ++++++++++++----- 1 file changed, 12 insertions(+), 5 deletions(-) diff --git a/drivers/char/tty_ldisc.c b/drivers/char/tty_ldisc.c index be55dfcf59a..1733d3439ad 100644 --- a/drivers/char/tty_ldisc.c +++ b/drivers/char/tty_ldisc.c @@ -55,25 +55,32 @@ static inline struct tty_ldisc *get_ldisc(struct tty_ldisc *ld) return ld; } -static inline void put_ldisc(struct tty_ldisc *ld) +static void put_ldisc(struct tty_ldisc *ld) { + unsigned long flags; + if (WARN_ON_ONCE(!ld)) return; /* * If this is the last user, free the ldisc, and * release the ldisc ops. + * + * We really want an "atomic_dec_and_lock_irqsave()", + * but we don't have it, so this does it by hand. */ - if (atomic_dec_and_test(&ld->users)) { - unsigned long flags; + local_irq_save(flags); + if (atomic_dec_and_lock(&ld->users, &tty_ldisc_lock)) { struct tty_ldisc_ops *ldo = ld->ops; - kfree(ld); - spin_lock_irqsave(&tty_ldisc_lock, flags); ldo->refcount--; module_put(ldo->owner); spin_unlock_irqrestore(&tty_ldisc_lock, flags); + + kfree(ld); + return; } + local_irq_restore(flags); } /** -- GitLab From 07868201070d87484bd00610a4921e879be78746 Mon Sep 17 00:00:00 2001 From: Jonathan Corbet Date: Tue, 4 Aug 2009 13:35:17 -0600 Subject: [PATCH 0805/1342] flex_array: remove unneeded index calculation flex_array_get() calculates an index value, then drops it on the floor; simply remove it. Signed-off-by: Jonathan Corbet Acked-by: Dave Hansen Signed-off-by: Linus Torvalds --- lib/flex_array.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/lib/flex_array.c b/lib/flex_array.c index 0e7894ce888..08f1636d296 100644 --- a/lib/flex_array.c +++ b/lib/flex_array.c @@ -254,7 +254,6 @@ void *flex_array_get(struct flex_array *fa, int element_nr) { int part_nr = fa_element_to_part_nr(fa, element_nr); struct flex_array_part *part; - int index; if (element_nr >= fa->total_nr_elements) return NULL; @@ -264,6 +263,5 @@ void *flex_array_get(struct flex_array *fa, int element_nr) part = (struct flex_array_part *)&fa->parts[0]; else part = fa->parts[part_nr]; - index = index_inside_part(fa, element_nr); return &part->elements[index_inside_part(fa, element_nr)]; } -- GitLab From 6502fbfaf81b09b3f474bb7b3796257e9450273e Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Tue, 4 Aug 2009 11:24:24 -0400 Subject: [PATCH 0806/1342] drm/radeon: Add support for RS880 chips These are new AMD IGP chips Signed-off-by: Alex Deucher Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r600_cp.c | 22 +++++++++++++++------- drivers/gpu/drm/radeon/radeon_drv.h | 1 + include/drm/drm_pciids.h | 5 +++++ 3 files changed, 21 insertions(+), 7 deletions(-) diff --git a/drivers/gpu/drm/radeon/r600_cp.c b/drivers/gpu/drm/radeon/r600_cp.c index 146f3570af8..20f17908b03 100644 --- a/drivers/gpu/drm/radeon/r600_cp.c +++ b/drivers/gpu/drm/radeon/r600_cp.c @@ -384,8 +384,9 @@ static void r600_cp_load_microcode(drm_radeon_private_t *dev_priv) DRM_INFO("Loading RV670 PFP Microcode\n"); for (i = 0; i < PFP_UCODE_SIZE; i++) RADEON_WRITE(R600_CP_PFP_UCODE_DATA, RV670_pfp_microcode[i]); - } else if (((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780)) { - DRM_INFO("Loading RS780 CP Microcode\n"); + } else if (((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780) || + ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS880)) { + DRM_INFO("Loading RS780/RS880 CP Microcode\n"); for (i = 0; i < PM4_UCODE_SIZE; i++) { RADEON_WRITE(R600_CP_ME_RAM_DATA, RS780_cp_microcode[i][0]); @@ -396,7 +397,7 @@ static void r600_cp_load_microcode(drm_radeon_private_t *dev_priv) } RADEON_WRITE(R600_CP_PFP_UCODE_ADDR, 0); - DRM_INFO("Loading RS780 PFP Microcode\n"); + DRM_INFO("Loading RS780/RS880 PFP Microcode\n"); for (i = 0; i < PFP_UCODE_SIZE; i++) RADEON_WRITE(R600_CP_PFP_UCODE_DATA, RS780_pfp_microcode[i]); } @@ -783,6 +784,7 @@ static void r600_gfx_init(struct drm_device *dev, break; case CHIP_RV610: case CHIP_RS780: + case CHIP_RS880: case CHIP_RV620: dev_priv->r600_max_pipes = 1; dev_priv->r600_max_tile_pipes = 1; @@ -917,7 +919,8 @@ static void r600_gfx_init(struct drm_device *dev, ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV630) || ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV610) || ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV620) || - ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780)) + ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780) || + ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS880)) RADEON_WRITE(R600_DB_DEBUG, R600_PREZ_MUST_WAIT_FOR_POSTZ_DONE); else RADEON_WRITE(R600_DB_DEBUG, 0); @@ -935,7 +938,8 @@ static void r600_gfx_init(struct drm_device *dev, sq_ms_fifo_sizes = RADEON_READ(R600_SQ_MS_FIFO_SIZES); if (((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV610) || ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV620) || - ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780)) { + ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780) || + ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS880)) { sq_ms_fifo_sizes = (R600_CACHE_FIFO_SIZE(0xa) | R600_FETCH_FIFO_HIWATER(0xa) | R600_DONE_FIFO_HIWATER(0xe0) | @@ -978,7 +982,8 @@ static void r600_gfx_init(struct drm_device *dev, R600_NUM_ES_STACK_ENTRIES(0)); } else if (((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV610) || ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV620) || - ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780)) { + ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780) || + ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS880)) { /* no vertex cache */ sq_config &= ~R600_VC_ENABLE; @@ -1035,7 +1040,8 @@ static void r600_gfx_init(struct drm_device *dev, if (((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV610) || ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV620) || - ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780)) + ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780) || + ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS880)) RADEON_WRITE(R600_VGT_CACHE_INVALIDATION, R600_CACHE_INVALIDATION(R600_TC_ONLY)); else RADEON_WRITE(R600_VGT_CACHE_INVALIDATION, R600_CACHE_INVALIDATION(R600_VC_AND_TC)); @@ -1078,6 +1084,7 @@ static void r600_gfx_init(struct drm_device *dev, break; case CHIP_RV610: case CHIP_RS780: + case CHIP_RS880: case CHIP_RV620: gs_prim_buffer_depth = 32; break; @@ -1123,6 +1130,7 @@ static void r600_gfx_init(struct drm_device *dev, switch (dev_priv->flags & RADEON_FAMILY_MASK) { case CHIP_RV610: case CHIP_RS780: + case CHIP_RS880: case CHIP_RV620: tc_cntl = R600_TC_L2_SIZE(8); break; diff --git a/drivers/gpu/drm/radeon/radeon_drv.h b/drivers/gpu/drm/radeon/radeon_drv.h index 127d0456f62..3933f8216a3 100644 --- a/drivers/gpu/drm/radeon/radeon_drv.h +++ b/drivers/gpu/drm/radeon/radeon_drv.h @@ -143,6 +143,7 @@ enum radeon_family { CHIP_RV635, CHIP_RV670, CHIP_RS780, + CHIP_RS880, CHIP_RV770, CHIP_RV730, CHIP_RV710, diff --git a/include/drm/drm_pciids.h b/include/drm/drm_pciids.h index 9d4c0049154..853508499d2 100644 --- a/include/drm/drm_pciids.h +++ b/include/drm/drm_pciids.h @@ -370,6 +370,11 @@ {0x1002, 0x9614, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS780|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \ {0x1002, 0x9615, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS780|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \ {0x1002, 0x9616, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS780|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \ + {0x1002, 0x9710, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS880|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \ + {0x1002, 0x9711, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS880|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \ + {0x1002, 0x9712, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS880|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \ + {0x1002, 0x9713, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS880|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \ + {0x1002, 0x9714, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS880|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \ {0, 0, 0} #define r128_PCI_IDS \ -- GitLab From 685aaca751271b2c5191901931a19ccaceeae1ce Mon Sep 17 00:00:00 2001 From: "Jory A. Pratt" Date: Mon, 3 Aug 2009 09:32:34 -0700 Subject: [PATCH 0807/1342] Input: i8042 - add Asus G1S to noloop exception list The synaptic touchpad on the Asus G1S is not properly detected when rebooting machine or on cold boot from time to time. Adding the Asus G1S to the noloop exception table resolves the issue. # dmidecode 2.10 SMBIOS 2.4 present. Handle 0x0001, DMI type 1, 27 bytes System Information Manufacturer: ASUSTeK Computer Inc. Product Name: G1S Version: 1.0 Wake-up Type: Power Switch SKU Number: Family: Signed-off-by: Jory A. Pratt Signed-off-by: Dmitry Torokhov --- drivers/input/serio/i8042-x86ia64io.h | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/drivers/input/serio/i8042-x86ia64io.h b/drivers/input/serio/i8042-x86ia64io.h index 924e8ed7f2c..ae04d8a494e 100644 --- a/drivers/input/serio/i8042-x86ia64io.h +++ b/drivers/input/serio/i8042-x86ia64io.h @@ -77,6 +77,14 @@ static struct dmi_system_id __initdata i8042_dmi_noloop_table[] = { DMI_MATCH(DMI_BOARD_VERSION, "Rev E"), }, }, + { + .ident = "ASUS G1S", + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, "ASUSTeK Computer Inc."), + DMI_MATCH(DMI_BOARD_NAME, "G1S"), + DMI_MATCH(DMI_BOARD_VERSION, "1.0"), + }, + }, { /* AUX LOOP command does not raise AUX IRQ */ .ident = "ASUS P65UP5", -- GitLab From f532959b77e5e567c84c914cb7c7b07d2582448b Mon Sep 17 00:00:00 2001 From: Fenghua Yu Date: Tue, 4 Aug 2009 15:09:37 -0700 Subject: [PATCH 0808/1342] intel-iommu: Correct sglist size calculation. In domain_sg_mapping(), use aligned_nrpages() instead of hand-coded rounding code for calculating the size of each sg elem. This means that on IA64 we correctly round up to the MM page size, not just to the VT-d page size. Also remove the incorrect mm_to_dma_pfn() when intel_map_sg() calls domain_sg_mapping() -- the 'size' variable is in VT-d pages already. Signed-off-by: Fenghua Yu Signed-off-by: David Woodhouse --- drivers/pci/intel-iommu.c | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) diff --git a/drivers/pci/intel-iommu.c b/drivers/pci/intel-iommu.c index ebc9b8dca88..11b317a78b4 100644 --- a/drivers/pci/intel-iommu.c +++ b/drivers/pci/intel-iommu.c @@ -1648,6 +1648,14 @@ static int domain_context_mapped(struct pci_dev *pdev) tmp->devfn); } +/* Returns a number of VTD pages, but aligned to MM page size */ +static inline unsigned long aligned_nrpages(unsigned long host_addr, + size_t size) +{ + host_addr &= ~PAGE_MASK; + return PAGE_ALIGN(host_addr + size) >> VTD_PAGE_SHIFT; +} + static int __domain_mapping(struct dmar_domain *domain, unsigned long iov_pfn, struct scatterlist *sg, unsigned long phys_pfn, unsigned long nr_pages, int prot) @@ -1675,7 +1683,7 @@ static int __domain_mapping(struct dmar_domain *domain, unsigned long iov_pfn, uint64_t tmp; if (!sg_res) { - sg_res = (sg->offset + sg->length + VTD_PAGE_SIZE - 1) >> VTD_PAGE_SHIFT; + sg_res = aligned_nrpages(sg->offset, sg->length); sg->dma_address = ((dma_addr_t)iov_pfn << VTD_PAGE_SHIFT) + sg->offset; sg->dma_length = sg->length; pteval = page_to_phys(sg_page(sg)) | prot; @@ -2415,14 +2423,6 @@ error: return ret; } -/* Returns a number of VTD pages, but aligned to MM page size */ -static inline unsigned long aligned_nrpages(unsigned long host_addr, - size_t size) -{ - host_addr &= ~PAGE_MASK; - return PAGE_ALIGN(host_addr + size) >> VTD_PAGE_SHIFT; -} - /* This takes a number of _MM_ pages, not VTD pages */ static struct iova *intel_alloc_iova(struct device *dev, struct dmar_domain *domain, @@ -2875,7 +2875,7 @@ static int intel_map_sg(struct device *hwdev, struct scatterlist *sglist, int ne start_vpfn = mm_to_dma_pfn(iova->pfn_lo); - ret = domain_sg_mapping(domain, start_vpfn, sglist, mm_to_dma_pfn(size), prot); + ret = domain_sg_mapping(domain, start_vpfn, sglist, size, prot); if (unlikely(ret)) { /* clear the page */ dma_pte_clear_range(domain, start_vpfn, -- GitLab From 33041ec049d39a6e0463c7edc7b6f631d24559e3 Mon Sep 17 00:00:00 2001 From: Fenghua Yu Date: Tue, 4 Aug 2009 15:10:59 -0700 Subject: [PATCH 0809/1342] intel-iommu: Mask physical address to correct page size in intel_map_single() The physical address passed to domain_pfn_mapping() should be rounded down to the start of the MM page, not the VT-d page. This issue causes kernel panic on PAGE_SIZE>VTD_PAGE_SIZE platforms e.g. ia64 platforms. Signed-off-by: Fenghua Yu Signed-off-by: David Woodhouse --- drivers/pci/intel-iommu.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/pci/intel-iommu.c b/drivers/pci/intel-iommu.c index 11b317a78b4..af7ff9b5aed 100644 --- a/drivers/pci/intel-iommu.c +++ b/drivers/pci/intel-iommu.c @@ -2551,6 +2551,7 @@ static dma_addr_t __intel_map_single(struct device *hwdev, phys_addr_t paddr, int prot = 0; int ret; struct intel_iommu *iommu; + unsigned long paddr_pfn = paddr >> PAGE_SHIFT; BUG_ON(dir == DMA_NONE); @@ -2585,7 +2586,7 @@ static dma_addr_t __intel_map_single(struct device *hwdev, phys_addr_t paddr, * is not a big problem */ ret = domain_pfn_mapping(domain, mm_to_dma_pfn(iova->pfn_lo), - paddr >> VTD_PAGE_SHIFT, size, prot); + mm_to_dma_pfn(paddr_pfn), size, prot); if (ret) goto error; -- GitLab From 7d5b005652bc5ae3e1e0efc53fd0e25a643ec506 Mon Sep 17 00:00:00 2001 From: Alok Kataria Date: Tue, 4 Aug 2009 15:34:22 -0700 Subject: [PATCH 0810/1342] x86: Fix VMI && stack protector With CONFIG_STACK_PROTECTOR turned on, VMI doesn't boot with more than one processor. The problem is with the gs value not being initialized correctly when registering the secondary processor for VMI's case. The patch below initializes the gs value for the AP to __KERNEL_STACK_CANARY. Without this the secondary processor keeps on taking a GP on every gs access. Signed-off-by: Alok N Kataria Cc: # for v2.6.30.x LKML-Reference: <1249425262.18955.40.camel@ank32.eng.vmware.com> Signed-off-by: Ingo Molnar --- arch/x86/kernel/vmi_32.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/vmi_32.c b/arch/x86/kernel/vmi_32.c index b263423fbe2..95a7289e4b0 100644 --- a/arch/x86/kernel/vmi_32.c +++ b/arch/x86/kernel/vmi_32.c @@ -441,7 +441,7 @@ vmi_startup_ipi_hook(int phys_apicid, unsigned long start_eip, ap.ds = __USER_DS; ap.es = __USER_DS; ap.fs = __KERNEL_PERCPU; - ap.gs = 0; + ap.gs = __KERNEL_STACK_CANARY; ap.eflags = 0; -- GitLab From e125e7b6944898831b56739a5448e705578bf7e2 Mon Sep 17 00:00:00 2001 From: Jan Kiszka Date: Thu, 2 Jul 2009 21:45:47 +0200 Subject: [PATCH 0811/1342] KVM: Fix KVM_GET_MSR_INDEX_LIST So far, KVM copied the emulated_msrs (only MSR_IA32_MISC_ENABLE) to a wrong address in user space due to broken pointer arithmetic. This caused subtle corruption up there (missing MSR_IA32_MISC_ENABLE had probably no practical relevance). Moreover, the size check for the user-provided kvm_msr_list forgot about emulated MSRs. Cc: stable@kernel.org Signed-off-by: Jan Kiszka Signed-off-by: Avi Kivity --- arch/x86/kvm/x86.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c index fe5474aec41..7bc311464fa 100644 --- a/arch/x86/kvm/x86.c +++ b/arch/x86/kvm/x86.c @@ -1079,14 +1079,13 @@ long kvm_arch_dev_ioctl(struct file *filp, if (copy_to_user(user_msr_list, &msr_list, sizeof msr_list)) goto out; r = -E2BIG; - if (n < num_msrs_to_save) + if (n < msr_list.nmsrs) goto out; r = -EFAULT; if (copy_to_user(user_msr_list->indices, &msrs_to_save, num_msrs_to_save * sizeof(u32))) goto out; - if (copy_to_user(user_msr_list->indices - + num_msrs_to_save * sizeof(u32), + if (copy_to_user(user_msr_list->indices + num_msrs_to_save, &emulated_msrs, ARRAY_SIZE(emulated_msrs) * sizeof(u32))) goto out; -- GitLab From 0ff77873b1318fc2d77a85e70690d3cd6cafbd41 Mon Sep 17 00:00:00 2001 From: Marcelo Tosatti Date: Thu, 2 Jul 2009 20:02:15 -0300 Subject: [PATCH 0812/1342] KVM: PIT: fix kpit_elapsed division by zero Fix division by zero triggered by latch count command on uninitialized counter. Cc: stable@kernel.org Signed-off-by: Marcelo Tosatti Signed-off-by: Avi Kivity --- arch/x86/kvm/i8254.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/x86/kvm/i8254.c b/arch/x86/kvm/i8254.c index 4d6f0d293ee..21f68e00524 100644 --- a/arch/x86/kvm/i8254.c +++ b/arch/x86/kvm/i8254.c @@ -104,6 +104,9 @@ static s64 __kpit_elapsed(struct kvm *kvm) ktime_t remaining; struct kvm_kpit_state *ps = &kvm->arch.vpit->pit_state; + if (!ps->pit_timer.period) + return 0; + /* * The Counter does not stop when it reaches zero. In * Modes 0, 1, 4, and 5 the Counter ``wraps around'' to -- GitLab From d6289b9365c3f622a8cfe62c4fb054bb70b5061a Mon Sep 17 00:00:00 2001 From: Marcelo Tosatti Date: Mon, 22 Jun 2009 15:27:56 -0300 Subject: [PATCH 0813/1342] KVM: x86: verify MTRR/PAT validity Do not allow invalid memory types in MTRR/PAT (generating a #GP otherwise). Signed-off-by: Marcelo Tosatti Signed-off-by: Avi Kivity --- arch/x86/kvm/x86.c | 39 ++++++++++++++++++++++++++++++++++++++- 1 file changed, 38 insertions(+), 1 deletion(-) diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c index 7bc311464fa..3d452901182 100644 --- a/arch/x86/kvm/x86.c +++ b/arch/x86/kvm/x86.c @@ -704,11 +704,48 @@ static bool msr_mtrr_valid(unsigned msr) return false; } +static bool valid_pat_type(unsigned t) +{ + return t < 8 && (1 << t) & 0xf3; /* 0, 1, 4, 5, 6, 7 */ +} + +static bool valid_mtrr_type(unsigned t) +{ + return t < 8 && (1 << t) & 0x73; /* 0, 1, 4, 5, 6 */ +} + +static bool mtrr_valid(struct kvm_vcpu *vcpu, u32 msr, u64 data) +{ + int i; + + if (!msr_mtrr_valid(msr)) + return false; + + if (msr == MSR_IA32_CR_PAT) { + for (i = 0; i < 8; i++) + if (!valid_pat_type((data >> (i * 8)) & 0xff)) + return false; + return true; + } else if (msr == MSR_MTRRdefType) { + if (data & ~0xcff) + return false; + return valid_mtrr_type(data & 0xff); + } else if (msr >= MSR_MTRRfix64K_00000 && msr <= MSR_MTRRfix4K_F8000) { + for (i = 0; i < 8 ; i++) + if (!valid_mtrr_type((data >> (i * 8)) & 0xff)) + return false; + return true; + } + + /* variable MTRRs */ + return valid_mtrr_type(data & 0xff); +} + static int set_msr_mtrr(struct kvm_vcpu *vcpu, u32 msr, u64 data) { u64 *p = (u64 *)&vcpu->arch.mtrr_state.fixed_ranges; - if (!msr_mtrr_valid(msr)) + if (!mtrr_valid(vcpu, msr, data)) return 1; if (msr == MSR_MTRRdefType) { -- GitLab From 4b656b1202498184a0ecef86b3b89ff613b9c6ab Mon Sep 17 00:00:00 2001 From: Marcelo Tosatti Date: Tue, 21 Jul 2009 12:47:45 -0300 Subject: [PATCH 0814/1342] KVM: SVM: force new asid on vcpu migration If a migrated vcpu matches the asid_generation value of the target pcpu, there will be no TLB flush via TLB_CONTROL_FLUSH_ALL_ASID. The check for vcpu.cpu in pre_svm_run is meaningless since svm_vcpu_load already updated it on schedule in. Such vcpu will VMRUN with stale TLB entries. Based on original patch from Joerg Roedel (http://patchwork.kernel.org/patch/10021/) Signed-off-by: Marcelo Tosatti Acked-by: Joerg Roedel Signed-off-by: Avi Kivity --- arch/x86/kvm/svm.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/x86/kvm/svm.c b/arch/x86/kvm/svm.c index 71510e07e69..b1f658ad2f0 100644 --- a/arch/x86/kvm/svm.c +++ b/arch/x86/kvm/svm.c @@ -711,6 +711,7 @@ static void svm_vcpu_load(struct kvm_vcpu *vcpu, int cpu) svm->vmcb->control.tsc_offset += delta; vcpu->cpu = cpu; kvm_migrate_timers(vcpu); + svm->asid_generation = 0; } for (i = 0; i < NR_HOST_SAVE_USER_MSRS; i++) @@ -1031,7 +1032,6 @@ static void new_asid(struct vcpu_svm *svm, struct svm_cpu_data *svm_data) svm->vmcb->control.tlb_ctl = TLB_CONTROL_FLUSH_ALL_ASID; } - svm->vcpu.cpu = svm_data->cpu; svm->asid_generation = svm_data->asid_generation; svm->vmcb->control.asid = svm_data->next_asid++; } @@ -2300,8 +2300,8 @@ static void pre_svm_run(struct vcpu_svm *svm) struct svm_cpu_data *svm_data = per_cpu(svm_data, cpu); svm->vmcb->control.tlb_ctl = TLB_CONTROL_DO_NOTHING; - if (svm->vcpu.cpu != cpu || - svm->asid_generation != svm_data->asid_generation) + /* FIXME: handle wraparound of asid_generation */ + if (svm->asid_generation != svm_data->asid_generation) new_asid(svm, svm_data); } -- GitLab From 025dbbf36a7680bffe54d9dcbf0a8bc01a7cbd10 Mon Sep 17 00:00:00 2001 From: Marcelo Tosatti Date: Wed, 22 Jul 2009 13:05:49 -0300 Subject: [PATCH 0815/1342] KVM: MMU: handle n_free_mmu_pages > n_alloc_mmu_pages in kvm_mmu_change_mmu_pages kvm_mmu_change_mmu_pages mishandles the case where n_alloc_mmu_pages is smaller then n_free_mmu_pages, by not checking if the result of the subtraction is negative. Its a valid condition which can happen if a large number of pages has been recently freed. Signed-off-by: Marcelo Tosatti Signed-off-by: Avi Kivity --- arch/x86/kvm/mmu.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-) diff --git a/arch/x86/kvm/mmu.c b/arch/x86/kvm/mmu.c index 7030b5f911b..49a10d00830 100644 --- a/arch/x86/kvm/mmu.c +++ b/arch/x86/kvm/mmu.c @@ -1407,24 +1407,25 @@ static int kvm_mmu_zap_page(struct kvm *kvm, struct kvm_mmu_page *sp) */ void kvm_mmu_change_mmu_pages(struct kvm *kvm, unsigned int kvm_nr_mmu_pages) { + int used_pages; + + used_pages = kvm->arch.n_alloc_mmu_pages - kvm->arch.n_free_mmu_pages; + used_pages = max(0, used_pages); + /* * If we set the number of mmu pages to be smaller be than the * number of actived pages , we must to free some mmu pages before we * change the value */ - if ((kvm->arch.n_alloc_mmu_pages - kvm->arch.n_free_mmu_pages) > - kvm_nr_mmu_pages) { - int n_used_mmu_pages = kvm->arch.n_alloc_mmu_pages - - kvm->arch.n_free_mmu_pages; - - while (n_used_mmu_pages > kvm_nr_mmu_pages) { + if (used_pages > kvm_nr_mmu_pages) { + while (used_pages > kvm_nr_mmu_pages) { struct kvm_mmu_page *page; page = container_of(kvm->arch.active_mmu_pages.prev, struct kvm_mmu_page, link); kvm_mmu_zap_page(kvm, page); - n_used_mmu_pages--; + used_pages--; } kvm->arch.n_free_mmu_pages = 0; } -- GitLab From 34f0c1ad27a74bd5eb0f99ea43ab6a4658d6419d Mon Sep 17 00:00:00 2001 From: Jan Kiszka Date: Wed, 22 Jul 2009 23:53:26 +0200 Subject: [PATCH 0816/1342] KVM: VMX: Fix locking order in handle_invalid_guest_state Release and re-acquire preemption and IRQ lock in the same order as vcpu_enter_guest does. Signed-off-by: Jan Kiszka Signed-off-by: Marcelo Tosatti Signed-off-by: Avi Kivity --- arch/x86/kvm/vmx.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/x86/kvm/vmx.c b/arch/x86/kvm/vmx.c index 356a0ce85c6..6bf58c083f0 100644 --- a/arch/x86/kvm/vmx.c +++ b/arch/x86/kvm/vmx.c @@ -3157,8 +3157,8 @@ static void handle_invalid_guest_state(struct kvm_vcpu *vcpu, struct vcpu_vmx *vmx = to_vmx(vcpu); enum emulation_result err = EMULATE_DONE; - preempt_enable(); local_irq_enable(); + preempt_enable(); while (!guest_state_valid(vcpu)) { err = emulate_instruction(vcpu, kvm_run, 0, 0, 0); @@ -3177,8 +3177,8 @@ static void handle_invalid_guest_state(struct kvm_vcpu *vcpu, schedule(); } - local_irq_disable(); preempt_disable(); + local_irq_disable(); vmx->invalid_state_emulation_result = err; } -- GitLab From 263799a3616242201e20fd2025fe84047b1379b1 Mon Sep 17 00:00:00 2001 From: Jan Kiszka Date: Tue, 21 Jul 2009 10:43:07 +0200 Subject: [PATCH 0817/1342] KVM: VMX: Fix locking imbalance on emulation failure We have to disable preemption and IRQs on every exit from handle_invalid_guest_state, otherwise we generate at least a preempt_disable imbalance. Signed-off-by: Jan Kiszka Signed-off-by: Marcelo Tosatti Signed-off-by: Avi Kivity --- arch/x86/kvm/vmx.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kvm/vmx.c b/arch/x86/kvm/vmx.c index 6bf58c083f0..29f912927a5 100644 --- a/arch/x86/kvm/vmx.c +++ b/arch/x86/kvm/vmx.c @@ -3168,7 +3168,7 @@ static void handle_invalid_guest_state(struct kvm_vcpu *vcpu, if (err != EMULATE_DONE) { kvm_report_emulation_failure(vcpu, "emulation failure"); - return; + break; } if (signal_pending(current)) -- GitLab From d3bc2f91b4761a8d9f96bea167fef2f8c00dea54 Mon Sep 17 00:00:00 2001 From: Christian Borntraeger Date: Thu, 16 Jul 2009 17:17:37 +0200 Subject: [PATCH 0818/1342] KVM: s390: fix wait_queue handling There are two waitqueues in kvm for wait handling: vcpu->wq for virt/kvm/kvm_main.c and vpcu->arch.local_int.wq for the s390 specific wait code. the wait handling in kvm_s390_handle_wait was broken by using different wait_queues for add_wait queue and remove_wait_queue. There are two options to fix the problem: o move all the s390 specific code to vcpu->wq and remove vcpu->arch.local_int.wq o move all the s390 specific code to vcpu->arch.local_int.wq This patch chooses the 2nd variant for two reasons: o s390 does not use kvm_vcpu_block but implements its own enabled wait handling. Having a separate wait_queue make it clear, that our wait mechanism is different o the patch is much smaller Report-by: Julia Lawall Signed-off-by: Christian Borntraeger Signed-off-by: Marcelo Tosatti Signed-off-by: Avi Kivity --- arch/s390/kvm/interrupt.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/s390/kvm/interrupt.c b/arch/s390/kvm/interrupt.c index f04f5301b1b..4d613415c43 100644 --- a/arch/s390/kvm/interrupt.c +++ b/arch/s390/kvm/interrupt.c @@ -386,7 +386,7 @@ no_timer: } __unset_cpu_idle(vcpu); __set_current_state(TASK_RUNNING); - remove_wait_queue(&vcpu->wq, &wait); + remove_wait_queue(&vcpu->arch.local_int.wq, &wait); spin_unlock_bh(&vcpu->arch.local_int.lock); spin_unlock(&vcpu->arch.local_int.float_int->lock); hrtimer_try_to_cancel(&vcpu->arch.ckc_timer); -- GitLab From 5116d8f6b977970ebefc1932c0f313163a6ec91f Mon Sep 17 00:00:00 2001 From: "Michael S. Tsirkin" Date: Sun, 26 Jul 2009 17:10:01 +0300 Subject: [PATCH 0819/1342] KVM: fix ack not being delivered when msi present kvm_notify_acked_irq does not check irq type, so that it sometimes interprets msi vector as irq. As a result, ack notifiers are not called, which typially hangs the guest. The fix is to track and check irq type. Signed-off-by: Michael S. Tsirkin Signed-off-by: Avi Kivity --- include/linux/kvm_host.h | 1 + virt/kvm/irq_comm.c | 4 +++- 2 files changed, 4 insertions(+), 1 deletion(-) diff --git a/include/linux/kvm_host.h b/include/linux/kvm_host.h index 16713dc672e..3060bdc35ff 100644 --- a/include/linux/kvm_host.h +++ b/include/linux/kvm_host.h @@ -110,6 +110,7 @@ struct kvm_memory_slot { struct kvm_kernel_irq_routing_entry { u32 gsi; + u32 type; int (*set)(struct kvm_kernel_irq_routing_entry *e, struct kvm *kvm, int level); union { diff --git a/virt/kvm/irq_comm.c b/virt/kvm/irq_comm.c index a8bd466d00c..ddc17f0e2f3 100644 --- a/virt/kvm/irq_comm.c +++ b/virt/kvm/irq_comm.c @@ -160,7 +160,8 @@ void kvm_notify_acked_irq(struct kvm *kvm, unsigned irqchip, unsigned pin) unsigned gsi = pin; list_for_each_entry(e, &kvm->irq_routing, link) - if (e->irqchip.irqchip == irqchip && + if (e->type == KVM_IRQ_ROUTING_IRQCHIP && + e->irqchip.irqchip == irqchip && e->irqchip.pin == pin) { gsi = e->gsi; break; @@ -259,6 +260,7 @@ static int setup_routing_entry(struct kvm_kernel_irq_routing_entry *e, int delta; e->gsi = ue->gsi; + e->type = ue->type; switch (ue->type) { case KVM_IRQ_ROUTING_IRQCHIP: delta = 0; -- GitLab From 114cfab222233f50f46d7162cf7d99fdc6c271e5 Mon Sep 17 00:00:00 2001 From: Pekka Enberg Date: Wed, 5 Aug 2009 13:25:21 +0300 Subject: [PATCH 0820/1342] perf report: Make --sort comm,dso,symbol the default If you're doing performance testing, you're interested in the symbols anyway so lets make "--sort comm,dso,symbol" the default sort option. Signed-off-by: Pekka Enberg Acked-by: Peter Zijlstra Cc: acme@redhat.com LKML-Reference: <1249467921-10450-1-git-send-email-penberg@cs.helsinki.fi> Signed-off-by: Ingo Molnar --- tools/perf/builtin-report.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c index ce4f28645e6..8cb58d68a00 100644 --- a/tools/perf/builtin-report.c +++ b/tools/perf/builtin-report.c @@ -31,7 +31,7 @@ static char const *input_name = "perf.data"; static char *vmlinux = NULL; -static char default_sort_order[] = "comm,dso"; +static char default_sort_order[] = "comm,dso,symbol"; static char *sort_order = default_sort_order; static char *dso_list_str, *comm_list_str, *sym_list_str, *col_width_list_str; @@ -1424,7 +1424,7 @@ print_entries: if (sort_order == default_sort_order && parent_pattern == default_parent_pattern) { fprintf(fp, "#\n"); - fprintf(fp, "# (For more details, try: perf report --sort comm,dso,symbol)\n"); + fprintf(fp, "# (For a higher level overview, try: perf report --sort comm,dso)\n"); fprintf(fp, "#\n"); } fprintf(fp, "\n"); -- GitLab From c428dcc9b9f967945992a2f8529e8c50a31d7913 Mon Sep 17 00:00:00 2001 From: Stephen Rothwell Date: Wed, 17 Jun 2009 15:04:19 +1000 Subject: [PATCH 0821/1342] KVM: Make KVM_HPAGES_PER_HPAGE unsigned long to avoid build error on powerpc Eliminates this compiler warning: arch/powerpc/kvm/../../../virt/kvm/kvm_main.c:1178: error: integer overflow in expression Signed-off-by: Stephen Rothwell Signed-off-by: Avi Kivity --- arch/powerpc/include/asm/kvm_host.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/powerpc/include/asm/kvm_host.h b/arch/powerpc/include/asm/kvm_host.h index dfdf13c9fef..fddc3ed715f 100644 --- a/arch/powerpc/include/asm/kvm_host.h +++ b/arch/powerpc/include/asm/kvm_host.h @@ -34,7 +34,7 @@ #define KVM_COALESCED_MMIO_PAGE_OFFSET 1 /* We don't currently support large pages. */ -#define KVM_PAGES_PER_HPAGE (1<<31) +#define KVM_PAGES_PER_HPAGE (1UL << 31) struct kvm; struct kvm_run; -- GitLab From e9cbde8c158629cc96a26b2323c4a243536c1951 Mon Sep 17 00:00:00 2001 From: Avi Kivity Date: Mon, 6 Jul 2009 12:49:39 +0300 Subject: [PATCH 0822/1342] KVM: ia64: fix build failures due to ia64/unsigned long mismatches Signed-off-by: Avi Kivity --- arch/ia64/kvm/mmio.c | 6 ++++-- arch/ia64/kvm/vcpu.c | 6 +++--- arch/ia64/kvm/vcpu.h | 13 +++++++------ 3 files changed, 14 insertions(+), 11 deletions(-) diff --git a/arch/ia64/kvm/mmio.c b/arch/ia64/kvm/mmio.c index 21f63fffc37..9bf55afd08d 100644 --- a/arch/ia64/kvm/mmio.c +++ b/arch/ia64/kvm/mmio.c @@ -247,7 +247,8 @@ void emulate_io_inst(struct kvm_vcpu *vcpu, u64 padr, u64 ma) vcpu_get_fpreg(vcpu, inst.M9.f2, &v); /* Write high word. FIXME: this is a kludge! */ v.u.bits[1] &= 0x3ffff; - mmio_access(vcpu, padr + 8, &v.u.bits[1], 8, ma, IOREQ_WRITE); + mmio_access(vcpu, padr + 8, (u64 *)&v.u.bits[1], 8, + ma, IOREQ_WRITE); data = v.u.bits[0]; size = 3; } else if (inst.M10.major == 7 && inst.M10.x6 == 0x3B) { @@ -265,7 +266,8 @@ void emulate_io_inst(struct kvm_vcpu *vcpu, u64 padr, u64 ma) /* Write high word.FIXME: this is a kludge! */ v.u.bits[1] &= 0x3ffff; - mmio_access(vcpu, padr + 8, &v.u.bits[1], 8, ma, IOREQ_WRITE); + mmio_access(vcpu, padr + 8, (u64 *)&v.u.bits[1], + 8, ma, IOREQ_WRITE); data = v.u.bits[0]; size = 3; } else if (inst.M10.major == 7 && inst.M10.x6 == 0x31) { diff --git a/arch/ia64/kvm/vcpu.c b/arch/ia64/kvm/vcpu.c index 46b02cbcc87..cc406d064a0 100644 --- a/arch/ia64/kvm/vcpu.c +++ b/arch/ia64/kvm/vcpu.c @@ -461,7 +461,7 @@ void setreg(unsigned long regnum, unsigned long val, u64 vcpu_get_gr(struct kvm_vcpu *vcpu, unsigned long reg) { struct kvm_pt_regs *regs = vcpu_regs(vcpu); - u64 val; + unsigned long val; if (!reg) return 0; @@ -469,7 +469,7 @@ u64 vcpu_get_gr(struct kvm_vcpu *vcpu, unsigned long reg) return val; } -void vcpu_set_gr(struct kvm_vcpu *vcpu, u64 reg, u64 value, int nat) +void vcpu_set_gr(struct kvm_vcpu *vcpu, unsigned long reg, u64 value, int nat) { struct kvm_pt_regs *regs = vcpu_regs(vcpu); long sof = (regs->cr_ifs) & 0x7f; @@ -1072,7 +1072,7 @@ void kvm_ttag(struct kvm_vcpu *vcpu, INST64 inst) vcpu_set_gr(vcpu, inst.M46.r1, tag, 0); } -int vcpu_tpa(struct kvm_vcpu *vcpu, u64 vadr, u64 *padr) +int vcpu_tpa(struct kvm_vcpu *vcpu, u64 vadr, unsigned long *padr) { struct thash_data *data; union ia64_isr visr, pt_isr; diff --git a/arch/ia64/kvm/vcpu.h b/arch/ia64/kvm/vcpu.h index 042af92ced8..360724d3ae6 100644 --- a/arch/ia64/kvm/vcpu.h +++ b/arch/ia64/kvm/vcpu.h @@ -686,14 +686,15 @@ static inline int highest_inservice_irq(struct kvm_vcpu *vcpu) return highest_bits((int *)&(VMX(vcpu, insvc[0]))); } -extern void vcpu_get_fpreg(struct kvm_vcpu *vcpu, u64 reg, +extern void vcpu_get_fpreg(struct kvm_vcpu *vcpu, unsigned long reg, struct ia64_fpreg *val); -extern void vcpu_set_fpreg(struct kvm_vcpu *vcpu, u64 reg, +extern void vcpu_set_fpreg(struct kvm_vcpu *vcpu, unsigned long reg, struct ia64_fpreg *val); -extern u64 vcpu_get_gr(struct kvm_vcpu *vcpu, u64 reg); -extern void vcpu_set_gr(struct kvm_vcpu *vcpu, u64 reg, u64 val, int nat); -extern u64 vcpu_get_psr(struct kvm_vcpu *vcpu); -extern void vcpu_set_psr(struct kvm_vcpu *vcpu, u64 val); +extern u64 vcpu_get_gr(struct kvm_vcpu *vcpu, unsigned long reg); +extern void vcpu_set_gr(struct kvm_vcpu *vcpu, unsigned long reg, + u64 val, int nat); +extern unsigned long vcpu_get_psr(struct kvm_vcpu *vcpu); +extern void vcpu_set_psr(struct kvm_vcpu *vcpu, unsigned long val); extern u64 vcpu_thash(struct kvm_vcpu *vcpu, u64 vadr); extern void vcpu_bsw0(struct kvm_vcpu *vcpu); extern void thash_vhpt_insert(struct kvm_vcpu *v, u64 pte, -- GitLab From 2cdbc46d7b2cb0acb68c3ecad93b000552121fa6 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Wed, 5 Aug 2009 14:05:16 +0200 Subject: [PATCH 0823/1342] perf: Auto-detect libbfd Since the C++ demangling isn't needed for everybody and bfd/iberty aren't widely/easily available on all machines, make it optional. It also allows you to forcefully disable demangling by using NO_DEMANGLE=1 and otherwise tries to detect libbfd/libiberty combinations that result in a compiling demangler. Reported-by: Jens Axboe Signed-off-by: Peter Zijlstra Cc: Arnaldo Carvalho de Melo Cc: Kyle McMartin LKML-Reference: <20090801082048.GX12579@kernel.dk> Signed-off-by: Ingo Molnar --- tools/perf/Makefile | 18 +++++++++++++++++- tools/perf/util/symbol.c | 9 +++++++++ 2 files changed, 26 insertions(+), 1 deletion(-) diff --git a/tools/perf/Makefile b/tools/perf/Makefile index 4b20fa47c3a..ff905aceb4f 100644 --- a/tools/perf/Makefile +++ b/tools/perf/Makefile @@ -345,7 +345,6 @@ BUILTIN_OBJS += builtin-stat.o BUILTIN_OBJS += builtin-top.o PERFLIBS = $(LIB_FILE) -EXTLIBS = -lbfd -liberty # # Platform specific tweaks @@ -374,6 +373,23 @@ ifeq ($(uname_S),Darwin) PTHREAD_LIBS = endif +ifdef NO_DEMANGLE + BASIC_CFLAGS += -DNO_DEMANGLE +else + + has_bfd := $(shell sh -c "(echo '\#include '; echo '\#include '; echo '\#ifndef DMGL_PARAMS'; echo '\#define DMGL_PARAMS (1 << 0)'; echo '\#define DMGL_ANSI (1 << 1)'; echo '\#endif'; echo 'int main(int argc, char **argv) { bfd_demangle(NULL, argv[0], DMGL_PARAMS | DMGL_ANSI); return 0; }') | gcc -x c - -lbfd > /dev/null 2>&1 && echo y") + + has_bfd_iberty := $(shell sh -c "(echo '\#include '; echo '\#include '; echo '\#ifndef DMGL_PARAMS'; echo '\#define DMGL_PARAMS (1 << 0)'; echo '\#define DMGL_ANSI (1 << 1)'; echo '\#endif'; echo 'int main(int argc, char **argv) { bfd_demangle(NULL, argv[0], DMGL_PARAMS | DMGL_ANSI); return 0; }') | gcc -x c - -lbfd -liberty > /dev/null 2>&1 && echo y") + + ifeq ($(has_bfd),y) + EXTLIBS += -lbfd + else ifeq ($(has_bfd_iberty),y) + EXTLIBS += -lbfd -liberty + else + BASIC_CFLAGS += -DNO_DEMANGLE + endif +endif + ifndef CC_LD_DYNPATH ifdef NO_R_TO_GCC_LINKER # Some gcc does not accept and pass -R to the linker to specify diff --git a/tools/perf/util/symbol.c b/tools/perf/util/symbol.c index b4fe0579bd6..0580b94785e 100644 --- a/tools/perf/util/symbol.c +++ b/tools/perf/util/symbol.c @@ -6,7 +6,16 @@ #include #include #include + +#ifndef NO_DEMANGLE #include +#else +static inline +char *bfd_demangle(void __used *v, const char __used *c, int __used i) +{ + return NULL; +} +#endif const char *sym_hist_filter; -- GitLab From b37c45b8c27c049dc44673e40fd63820fd9a9d91 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 5 Aug 2009 16:53:24 +0300 Subject: [PATCH 0824/1342] OMAP: GPIO: Fix incorrect gpio_get logic for output GPIOs gpio_get() should return DATAIN register value when the GPIO is configured as input whereas it should return DATAOUT register value when the GPIO is configured as output. Now /sys/kernel/debug/gpio shows proper values for output GPIOs Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/plat-omap/gpio.c | 121 ++++++++++++++++++++++++++++---------- 1 file changed, 89 insertions(+), 32 deletions(-) diff --git a/arch/arm/plat-omap/gpio.c b/arch/arm/plat-omap/gpio.c index 26b387c1242..9c16ca8d293 100644 --- a/arch/arm/plat-omap/gpio.c +++ b/arch/arm/plat-omap/gpio.c @@ -476,14 +476,12 @@ static void _set_gpio_dataout(struct gpio_bank *bank, int gpio, int enable) __raw_writel(l, reg); } -static int __omap_get_gpio_datain(int gpio) +static int _get_gpio_datain(struct gpio_bank *bank, int gpio) { - struct gpio_bank *bank; void __iomem *reg; if (check_gpio(gpio) < 0) return -EINVAL; - bank = get_gpio_bank(gpio); reg = bank->base; switch (bank->method) { #ifdef CONFIG_ARCH_OMAP1 @@ -524,6 +522,53 @@ static int __omap_get_gpio_datain(int gpio) & (1 << get_gpio_index(gpio))) != 0; } +static int _get_gpio_dataout(struct gpio_bank *bank, int gpio) +{ + void __iomem *reg; + + if (check_gpio(gpio) < 0) + return -EINVAL; + reg = bank->base; + + switch (bank->method) { +#ifdef CONFIG_ARCH_OMAP1 + case METHOD_MPUIO: + reg += OMAP_MPUIO_OUTPUT; + break; +#endif +#ifdef CONFIG_ARCH_OMAP15XX + case METHOD_GPIO_1510: + reg += OMAP1510_GPIO_DATA_OUTPUT; + break; +#endif +#ifdef CONFIG_ARCH_OMAP16XX + case METHOD_GPIO_1610: + reg += OMAP1610_GPIO_DATAOUT; + break; +#endif +#ifdef CONFIG_ARCH_OMAP730 + case METHOD_GPIO_730: + reg += OMAP730_GPIO_DATA_OUTPUT; + break; +#endif +#ifdef CONFIG_ARCH_OMAP850 + case METHOD_GPIO_850: + reg += OMAP850_GPIO_DATA_OUTPUT; + break; +#endif +#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \ + defined(CONFIG_ARCH_OMAP4) + case METHOD_GPIO_24XX: + reg += OMAP24XX_GPIO_DATAOUT; + break; +#endif + default: + return -EINVAL; + } + + return (__raw_readl(reg) & (1 << get_gpio_index(gpio))) != 0; +} + #define MOD_REG_BIT(reg, bit_mask, set) \ do { \ int l = __raw_readl(base + reg); \ @@ -1350,9 +1395,49 @@ static int gpio_input(struct gpio_chip *chip, unsigned offset) return 0; } +static int gpio_is_input(struct gpio_bank *bank, int mask) +{ + void __iomem *reg = bank->base; + + switch (bank->method) { + case METHOD_MPUIO: + reg += OMAP_MPUIO_IO_CNTL; + break; + case METHOD_GPIO_1510: + reg += OMAP1510_GPIO_DIR_CONTROL; + break; + case METHOD_GPIO_1610: + reg += OMAP1610_GPIO_DIRECTION; + break; + case METHOD_GPIO_730: + reg += OMAP730_GPIO_DIR_CONTROL; + break; + case METHOD_GPIO_850: + reg += OMAP850_GPIO_DIR_CONTROL; + break; + case METHOD_GPIO_24XX: + reg += OMAP24XX_GPIO_OE; + break; + } + return __raw_readl(reg) & mask; +} + static int gpio_get(struct gpio_chip *chip, unsigned offset) { - return __omap_get_gpio_datain(chip->base + offset); + struct gpio_bank *bank; + void __iomem *reg; + int gpio; + u32 mask; + + gpio = chip->base + offset; + bank = get_gpio_bank(gpio); + reg = bank->base; + mask = 1 << get_gpio_index(gpio); + + if (gpio_is_input(bank, mask)) + return _get_gpio_datain(bank, gpio); + else + return _get_gpio_dataout(bank, gpio); } static int gpio_output(struct gpio_chip *chip, unsigned offset, int value) @@ -1886,34 +1971,6 @@ arch_initcall(omap_gpio_sysinit); #include #include -static int gpio_is_input(struct gpio_bank *bank, int mask) -{ - void __iomem *reg = bank->base; - - switch (bank->method) { - case METHOD_MPUIO: - reg += OMAP_MPUIO_IO_CNTL; - break; - case METHOD_GPIO_1510: - reg += OMAP1510_GPIO_DIR_CONTROL; - break; - case METHOD_GPIO_1610: - reg += OMAP1610_GPIO_DIRECTION; - break; - case METHOD_GPIO_730: - reg += OMAP730_GPIO_DIR_CONTROL; - break; - case METHOD_GPIO_850: - reg += OMAP850_GPIO_DIR_CONTROL; - break; - case METHOD_GPIO_24XX: - reg += OMAP24XX_GPIO_OE; - break; - } - return __raw_readl(reg) & mask; -} - - static int dbg_gpio_show(struct seq_file *s, void *unused) { unsigned i, j, gpio; -- GitLab From 386c0b702b1ea81c0f54f5c9832a3d4a52270f14 Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Wed, 5 Aug 2009 10:04:53 -0300 Subject: [PATCH 0825/1342] perf report: Add missing command line options to man page Signed-off-by: Arnaldo Carvalho de Melo Cc: Peter Zijlstra LKML-Reference: <20090805130453.GC10688@ghostprotocols.net> Signed-off-by: Ingo Molnar --- tools/perf/Documentation/perf-record.txt | 60 ++++++++++++++++++++++-- 1 file changed, 57 insertions(+), 3 deletions(-) diff --git a/tools/perf/Documentation/perf-record.txt b/tools/perf/Documentation/perf-record.txt index 1dbc1eeb4c0..6be696b0a2b 100644 --- a/tools/perf/Documentation/perf-record.txt +++ b/tools/perf/Documentation/perf-record.txt @@ -29,13 +29,67 @@ OPTIONS Select the PMU event. Selection can be a symbolic event name (use 'perf list' to list all events) or a raw PMU event (eventsel+umask) in the form of rNNN where NNN is a - hexadecimal event descriptor. + hexadecimal event descriptor. -a:: - system-wide collection + System-wide collection. -l:: - scale counter values + Scale counter values. + +-p:: +--pid=:: + Record events on existing pid. + +-r:: +--realtime=:: + Collect data with this RT SCHED_FIFO priority. +-A:: +--append:: + Append to the output file to do incremental profiling. + +-f:: +--force:: + Overwrite existing data file. + +-c:: +--count=:: + Event period to sample. + +-o:: +--output=:: + Output file name. + +-i:: +--inherit:: + Child tasks inherit counters. +-F:: +--freq=:: + Profile at this frequency. + +-m:: +--mmap-pages=:: + Number of mmap data pages. + +-g:: +--call-graph:: + Do call-graph (stack chain/backtrace) recording. + +-v:: +--verbose:: + Be more verbose (show counter open errors, etc). + +-s:: +--stat:: + Per thread counts. + +-d:: +--data:: + Sample addresses. + +-n:: +--no-samples:: + Don't sample. SEE ALSO -------- -- GitLab From 0bf52b981770cbf006323bab5177f2858a196766 Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Tue, 4 Aug 2009 21:16:58 +0000 Subject: [PATCH 0826/1342] net: Fix spinlock use in alloc_netdev_mq() -tip testing found this lockdep warning: [ 2.272010] calling net_dev_init+0x0/0x164 @ 1 [ 2.276033] device class 'net': registering [ 2.280191] INFO: trying to register non-static key. [ 2.284005] the code is fine but needs lockdep annotation. [ 2.284005] turning off the locking correctness validator. [ 2.284005] Pid: 1, comm: swapper Not tainted 2.6.31-rc5-tip #1145 [ 2.284005] Call Trace: [ 2.284005] [<7958eb4e>] ? printk+0xf/0x11 [ 2.284005] [<7904f83c>] __lock_acquire+0x11b/0x622 [ 2.284005] [<7908c9b7>] ? alloc_debug_processing+0xf9/0x144 [ 2.284005] [<7904e2be>] ? mark_held_locks+0x3a/0x52 [ 2.284005] [<7908dbc4>] ? kmem_cache_alloc+0xa8/0x13f [ 2.284005] [<7904e475>] ? trace_hardirqs_on_caller+0xa2/0xc3 [ 2.284005] [<7904fdf6>] lock_acquire+0xb3/0xd0 [ 2.284005] [<79489678>] ? alloc_netdev_mq+0xf5/0x1ad [ 2.284005] [<79591514>] _spin_lock_bh+0x2d/0x5d [ 2.284005] [<79489678>] ? alloc_netdev_mq+0xf5/0x1ad [ 2.284005] [<79489678>] alloc_netdev_mq+0xf5/0x1ad [ 2.284005] [<793a38f2>] ? loopback_setup+0x0/0x74 [ 2.284005] [<798eecd0>] loopback_net_init+0x20/0x5d [ 2.284005] [<79483efb>] register_pernet_device+0x23/0x4b [ 2.284005] [<798f5c9f>] net_dev_init+0x115/0x164 [ 2.284005] [<7900104f>] do_one_initcall+0x4a/0x11a [ 2.284005] [<798f5b8a>] ? net_dev_init+0x0/0x164 [ 2.284005] [<79066f6d>] ? register_irq_proc+0x8c/0xa8 [ 2.284005] [<798cc29a>] do_basic_setup+0x42/0x52 [ 2.284005] [<798cc30a>] kernel_init+0x60/0xa1 [ 2.284005] [<798cc2aa>] ? kernel_init+0x0/0xa1 [ 2.284005] [<79003e03>] kernel_thread_helper+0x7/0x10 [ 2.284078] device: 'lo': device_add [ 2.288248] initcall net_dev_init+0x0/0x164 returned 0 after 11718 usecs [ 2.292010] calling neigh_init+0x0/0x66 @ 1 [ 2.296010] initcall neigh_init+0x0/0x66 returned 0 after 0 usecs it's using an zero-initialized spinlock. This is a side-effect of: dev_unicast_init(dev); in alloc_netdev_mq() making use of dev->addr_list_lock. The device has just been allocated freshly, it's not accessible anywhere yet so no locking is needed at all - in fact it's wrong to lock it here (the lock isnt initialized yet). This bug was introduced via: | commit a6ac65db2329e7685299666f5f7b6093c7b0f3a0 | Date: Thu Jul 30 01:06:12 2009 +0000 | | net: restore the original spinlock to protect unicast list Signed-off-by: Ingo Molnar Acked-by: Jiri Pirko Tested-by: Mark Brown Signed-off-by: David S. Miller --- net/core/dev.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/net/core/dev.c b/net/core/dev.c index 43e61ba7bd9..6a94475aee8 100644 --- a/net/core/dev.c +++ b/net/core/dev.c @@ -4007,9 +4007,7 @@ static void dev_unicast_flush(struct net_device *dev) static void dev_unicast_init(struct net_device *dev) { - netif_addr_lock_bh(dev); __hw_addr_init(&dev->uc); - netif_addr_unlock_bh(dev); } -- GitLab From 7cc515f74d2871daff106a17714bfd16bcb045ca Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Wed, 10 Jun 2009 09:02:25 -0700 Subject: [PATCH 0827/1342] OMAP2/3: PM: make PM __init calls static Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm.h | 3 --- arch/arm/mach-omap2/pm24xx.c | 2 +- arch/arm/mach-omap2/pm34xx.c | 2 +- 3 files changed, 2 insertions(+), 5 deletions(-) diff --git a/arch/arm/mach-omap2/pm.h b/arch/arm/mach-omap2/pm.h index f7b3baf7667..21201cd4117 100644 --- a/arch/arm/mach-omap2/pm.h +++ b/arch/arm/mach-omap2/pm.h @@ -11,9 +11,6 @@ #ifndef __ARCH_ARM_MACH_OMAP2_PM_H #define __ARCH_ARM_MACH_OMAP2_PM_H -extern int omap2_pm_init(void); -extern int omap3_pm_init(void); - #ifdef CONFIG_PM_DEBUG extern void omap2_pm_dump(int mode, int resume, unsigned int us); extern int omap2_pm_debug; diff --git a/arch/arm/mach-omap2/pm24xx.c b/arch/arm/mach-omap2/pm24xx.c index db1025562fb..528dbdc26e2 100644 --- a/arch/arm/mach-omap2/pm24xx.c +++ b/arch/arm/mach-omap2/pm24xx.c @@ -470,7 +470,7 @@ static void __init prcm_setup_regs(void) WKUP_MOD, PM_WKEN); } -int __init omap2_pm_init(void) +static int __init omap2_pm_init(void) { u32 l; diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index 841d4c5ed8b..765cdc0cd7a 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -652,7 +652,7 @@ static int __init clkdms_setup(struct clockdomain *clkdm) return 0; } -int __init omap3_pm_init(void) +static int __init omap3_pm_init(void) { struct power_state *pwrst, *tmp; int ret; -- GitLab From 364dd47466ff7a7749bf037df4bf3b7aedbfe6f4 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Tue, 9 Jun 2009 11:45:30 -0700 Subject: [PATCH 0828/1342] OMAP3: PM: CM_REGADDR macros using wrong name Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/cm.h | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm/mach-omap2/cm.h b/arch/arm/mach-omap2/cm.h index 1d3c93bf86d..f3c91a1ca39 100644 --- a/arch/arm/mach-omap2/cm.h +++ b/arch/arm/mach-omap2/cm.h @@ -29,9 +29,9 @@ * These registers appear once per CM module. */ -#define OMAP3430_CM_REVISION OMAP_CM_REGADDR(OCP_MOD, 0x0000) -#define OMAP3430_CM_SYSCONFIG OMAP_CM_REGADDR(OCP_MOD, 0x0010) -#define OMAP3430_CM_POLCTRL OMAP_CM_REGADDR(OCP_MOD, 0x009c) +#define OMAP3430_CM_REVISION OMAP34XX_CM_REGADDR(OCP_MOD, 0x0000) +#define OMAP3430_CM_SYSCONFIG OMAP34XX_CM_REGADDR(OCP_MOD, 0x0010) +#define OMAP3430_CM_POLCTRL OMAP34XX_CM_REGADDR(OCP_MOD, 0x009c) #define OMAP3_CM_CLKOUT_CTRL_OFFSET 0x0070 #define OMAP3430_CM_CLKOUT_CTRL OMAP_CM_REGADDR(OMAP3430_CCR_MOD, 0x0070) -- GitLab From 3a6667acf916b3e32be4682196882fc2ed0ec23e Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Mon, 27 Apr 2009 07:50:23 -0700 Subject: [PATCH 0829/1342] OMAP3: PM: Ensure PRCM interrupts are cleared at boot Any pending PRCM interrupts can prevent retention. Ensure they are cleared during boot. Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index 765cdc0cd7a..cc83dfc39a8 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -613,6 +613,9 @@ static void __init prcm_setup_regs(void) /* Clear any pending PRCM interrupts */ prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); + /* Clear any pending PRCM interrupts */ + prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); + omap3_iva_idle(); omap3_d2d_idle(); } -- GitLab From 3a07ae30a0bfa93ff2b242acf670c6d8e2de35de Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Mon, 27 Apr 2009 16:14:54 -0700 Subject: [PATCH 0830/1342] OMAP3: PM: Clear pending PRCM reset flags on init Any pending reset flags can prevent retention. Ensure they are all cleared during boot. Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index cc83dfc39a8..1422e931f57 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -613,6 +613,15 @@ static void __init prcm_setup_regs(void) /* Clear any pending PRCM interrupts */ prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); + /* Clear any pending 'reset' flags */ + prm_write_mod_reg(0xffffffff, MPU_MOD, RM_RSTST); + prm_write_mod_reg(0xffffffff, CORE_MOD, RM_RSTST); + prm_write_mod_reg(0xffffffff, OMAP3430_PER_MOD, RM_RSTST); + prm_write_mod_reg(0xffffffff, OMAP3430_EMU_MOD, RM_RSTST); + prm_write_mod_reg(0xffffffff, OMAP3430_NEON_MOD, RM_RSTST); + prm_write_mod_reg(0xffffffff, OMAP3430_DSS_MOD, RM_RSTST); + prm_write_mod_reg(0xffffffff, OMAP3430ES2_USBHOST_MOD, RM_RSTST); + /* Clear any pending PRCM interrupts */ prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); -- GitLab From 040fed059c34da5115790609f1a038fc9aec88d1 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Tue, 5 May 2009 16:34:25 -0700 Subject: [PATCH 0831/1342] OMAP3: PM: prevent module wakeups from waking IVA2 By default, prevent functional wakeups from inside a module from waking up the IVA2. Let DSP Bridge code handle this when loaded. Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index 1422e931f57..c813a081c3c 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -613,6 +613,12 @@ static void __init prcm_setup_regs(void) /* Clear any pending PRCM interrupts */ prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); + /* Don't attach IVA interrupts */ + prm_write_mod_reg(0, WKUP_MOD, OMAP3430_PM_IVAGRPSEL); + prm_write_mod_reg(0, CORE_MOD, OMAP3430_PM_IVAGRPSEL1); + prm_write_mod_reg(0, CORE_MOD, OMAP3430ES2_PM_IVAGRPSEL3); + prm_write_mod_reg(0, OMAP3430_PER_MOD, OMAP3430_PM_IVAGRPSEL); + /* Clear any pending 'reset' flags */ prm_write_mod_reg(0xffffffff, MPU_MOD, RM_RSTST); prm_write_mod_reg(0xffffffff, CORE_MOD, RM_RSTST); -- GitLab From 10f90ed2d727c0f344d910c02c9726d0481d9b00 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Wed, 24 Jun 2009 11:39:18 -0700 Subject: [PATCH 0832/1342] OMAP3: PM: Do not build suspend code if SUSPEND is not enabled Signed-off-by: Jouni Hogander Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index c813a081c3c..528f725722a 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -39,7 +39,9 @@ struct power_state { struct powerdomain *pwrdm; u32 next_state; +#ifdef CONFIG_SUSPEND u32 saved_state; +#endif struct list_head node; }; @@ -293,6 +295,7 @@ out: local_irq_enable(); } +#ifdef CONFIG_SUSPEND static int omap3_pm_prepare(void) { disable_hlt(); @@ -366,6 +369,7 @@ static struct platform_suspend_ops omap_pm_ops = { .finish = omap3_pm_finish, .valid = suspend_valid_only_mem, }; +#endif /* CONFIG_SUSPEND */ /** @@ -710,7 +714,9 @@ static int __init omap3_pm_init(void) _omap_sram_idle = omap_sram_push(omap34xx_cpu_suspend, omap34xx_cpu_suspend_sz); +#ifdef CONFIG_SUSPEND suspend_set_ops(&omap_pm_ops); +#endif /* CONFIG_SUSPEND */ pm_idle = omap3_pm_idle; -- GitLab From 4789998a30d845d94a7595076d1392ffd5a9d39e Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Wed, 24 Jun 2009 10:32:03 -0700 Subject: [PATCH 0833/1342] OMAP4: UART: cleanup special case IRQ handling Streamline the OMAP4 special IRQ assignments by putting inside normal init loop instead of having a separate loop. Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/serial.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index b094c15bfe4..c82ec95cd79 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -496,10 +496,6 @@ void __init omap_serial_init(void) if (info == NULL) return; - if (cpu_is_omap44xx()) { - for (i = 0; i < OMAP_MAX_NR_PORTS; i++) - serial_platform_data[i].irq += 32; - } for (i = 0; i < OMAP_MAX_NR_PORTS; i++) { struct plat_serial8250_port *p = serial_platform_data + i; @@ -533,6 +529,9 @@ void __init omap_serial_init(void) uart->p = p; list_add(&uart->node, &uart_list); + if (cpu_is_omap44xx()) + p->irq += 32; + omap_uart_enable_clocks(uart); omap_uart_reset(uart); omap_uart_idle_init(uart); -- GitLab From 2466211e5debd205fc550d871fe0ab9b9a6d02ed Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Thu, 5 Mar 2009 16:32:23 +0200 Subject: [PATCH 0834/1342] OMAP3: Fixed crash bug with serial + suspend It was possible for an unhandled interrupt to occur if there was incoming serial traffic during wakeup from suspend. This was caused by the code in arch-arm/mach-omap2/serial.c keeping interrupt enabled all the time, but not acking its interrupts. Applies on top of PM branch. Use the PM begin/end hooks to ensure that the "serial idle" interrupts are disabled during the suspend path. Also, since begin/end hooks are now used, use the suspend_state that is passed in the begin hook instead of the enter hook as per the platform_suspend_ops docs. Signed-off-by: Tero Kristo Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 23 +++++++++++++++++++++-- arch/arm/mach-omap2/serial.c | 14 ++++++++++++++ arch/arm/plat-omap/include/mach/serial.h | 1 + 3 files changed, 36 insertions(+), 2 deletions(-) diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index 528f725722a..b07efb26de1 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -296,6 +296,8 @@ out: } #ifdef CONFIG_SUSPEND +static suspend_state_t suspend_state; + static int omap3_pm_prepare(void) { disable_hlt(); @@ -342,11 +344,11 @@ restore: return ret; } -static int omap3_pm_enter(suspend_state_t state) +static int omap3_pm_enter(suspend_state_t unused) { int ret = 0; - switch (state) { + switch (suspend_state) { case PM_SUSPEND_STANDBY: case PM_SUSPEND_MEM: ret = omap3_pm_suspend(); @@ -363,7 +365,24 @@ static void omap3_pm_finish(void) enable_hlt(); } +/* Hooks to enable / disable UART interrupts during suspend */ +static int omap3_pm_begin(suspend_state_t state) +{ + suspend_state = state; + omap_uart_enable_irqs(0); + return 0; +} + +static void omap3_pm_end(void) +{ + suspend_state = PM_SUSPEND_ON; + omap_uart_enable_irqs(1); + return; +} + static struct platform_suspend_ops omap_pm_ops = { + .begin = omap3_pm_begin, + .end = omap3_pm_end, .prepare = omap3_pm_prepare, .enter = omap3_pm_enter, .finish = omap3_pm_finish, diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index c82ec95cd79..5352d05b42d 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -435,6 +435,20 @@ static void omap_uart_idle_init(struct omap_uart_state *uart) WARN_ON(ret); } +void omap_uart_enable_irqs(int enable) +{ + int ret; + struct omap_uart_state *uart; + + list_for_each_entry(uart, &uart_list, node) { + if (enable) + ret = request_irq(uart->p->irq, omap_uart_interrupt, + IRQF_SHARED, "serial idle", (void *)uart); + else + free_irq(uart->p->irq, (void *)uart); + } +} + static ssize_t sleep_timeout_show(struct kobject *kobj, struct kobj_attribute *attr, char *buf) diff --git a/arch/arm/plat-omap/include/mach/serial.h b/arch/arm/plat-omap/include/mach/serial.h index 13abd02d152..def0529c75e 100644 --- a/arch/arm/plat-omap/include/mach/serial.h +++ b/arch/arm/plat-omap/include/mach/serial.h @@ -59,6 +59,7 @@ extern void omap_uart_check_wakeup(void); extern void omap_uart_prepare_suspend(void); extern void omap_uart_prepare_idle(int num); extern void omap_uart_resume_idle(int num); +extern void omap_uart_enable_irqs(int enable); #endif #endif -- GitLab From fd455ea899b5a14a8cdd276e15f3b47696526f92 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Mon, 27 Apr 2009 12:27:36 -0700 Subject: [PATCH 0835/1342] OMAP2/3/4: UART: Allow per-UART disabling wakeup for serial ports This patch causes the OMAP uarts to honor the sysfs power/wakeup file for IOPAD wakeups. Before the OMAP was always woken up from off mode on a rs232 signal change. This patch also creates a different platform device for each serial port so that the wakeup properties can be control per port. By default, IOPAD wakeups are enabled for each UART. To disable, # echo disabled > /sys/devices/platform/serial8250.0/power/wakeup Where serial8250.0 can be replaced by .1, or .2 to control the other ports. Original idea and original patch from Russ Dill Cc: Russ Dill Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/serial.c | 174 +++++++++++++++++++++++------------ 1 file changed, 116 insertions(+), 58 deletions(-) diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index 5352d05b42d..6f35a7e4893 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -54,6 +54,7 @@ struct omap_uart_state { struct plat_serial8250_port *p; struct list_head node; + struct platform_device pdev; #if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM) int context_valid; @@ -68,10 +69,9 @@ struct omap_uart_state { #endif }; -static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS]; static LIST_HEAD(uart_list); -static struct plat_serial8250_port serial_platform_data[] = { +static struct plat_serial8250_port serial_platform_data0[] = { { .membase = IO_ADDRESS(OMAP_UART1_BASE), .mapbase = OMAP_UART1_BASE, @@ -81,6 +81,12 @@ static struct plat_serial8250_port serial_platform_data[] = { .regshift = 2, .uartclk = OMAP24XX_BASE_BAUD * 16, }, { + .flags = 0 + } +}; + +static struct plat_serial8250_port serial_platform_data1[] = { + { .membase = IO_ADDRESS(OMAP_UART2_BASE), .mapbase = OMAP_UART2_BASE, .irq = 73, @@ -89,6 +95,12 @@ static struct plat_serial8250_port serial_platform_data[] = { .regshift = 2, .uartclk = OMAP24XX_BASE_BAUD * 16, }, { + .flags = 0 + } +}; + +static struct plat_serial8250_port serial_platform_data2[] = { + { .membase = IO_ADDRESS(OMAP_UART3_BASE), .mapbase = OMAP_UART3_BASE, .irq = 74, @@ -217,6 +229,40 @@ static inline void omap_uart_disable_clocks(struct omap_uart_state *uart) clk_disable(uart->fck); } +static void omap_uart_enable_wakeup(struct omap_uart_state *uart) +{ + /* Set wake-enable bit */ + if (uart->wk_en && uart->wk_mask) { + u32 v = __raw_readl(uart->wk_en); + v |= uart->wk_mask; + __raw_writel(v, uart->wk_en); + } + + /* Ensure IOPAD wake-enables are set */ + if (cpu_is_omap34xx() && uart->padconf) { + u16 v = omap_ctrl_readw(uart->padconf); + v |= OMAP3_PADCONF_WAKEUPENABLE0; + omap_ctrl_writew(v, uart->padconf); + } +} + +static void omap_uart_disable_wakeup(struct omap_uart_state *uart) +{ + /* Clear wake-enable bit */ + if (uart->wk_en && uart->wk_mask) { + u32 v = __raw_readl(uart->wk_en); + v &= ~uart->wk_mask; + __raw_writel(v, uart->wk_en); + } + + /* Ensure IOPAD wake-enables are cleared */ + if (cpu_is_omap34xx() && uart->padconf) { + u16 v = omap_ctrl_readw(uart->padconf); + v &= ~OMAP3_PADCONF_WAKEUPENABLE0; + omap_ctrl_writew(v, uart->padconf); + } +} + static void omap_uart_smart_idle_enable(struct omap_uart_state *uart, int enable) { @@ -246,6 +292,11 @@ static void omap_uart_block_sleep(struct omap_uart_state *uart) static void omap_uart_allow_sleep(struct omap_uart_state *uart) { + if (device_may_wakeup(&uart->pdev.dev)) + omap_uart_enable_wakeup(uart); + else + omap_uart_disable_wakeup(uart); + if (!uart->clocked) return; @@ -292,7 +343,6 @@ void omap_uart_resume_idle(int num) /* Check for normal UART wakeup */ if (__raw_readl(uart->wk_st) & uart->wk_mask) omap_uart_block_sleep(uart); - return; } } @@ -346,16 +396,13 @@ static irqreturn_t omap_uart_interrupt(int irq, void *dev_id) return IRQ_NONE; } -static u32 sleep_timeout = DEFAULT_TIMEOUT; - static void omap_uart_idle_init(struct omap_uart_state *uart) { - u32 v; struct plat_serial8250_port *p = uart->p; int ret; uart->can_sleep = 0; - uart->timeout = sleep_timeout; + uart->timeout = DEFAULT_TIMEOUT; setup_timer(&uart->timer, omap_uart_idle_timer, (unsigned long) uart); mod_timer(&uart->timer, jiffies + uart->timeout); @@ -413,22 +460,6 @@ static void omap_uart_idle_init(struct omap_uart_state *uart) uart->padconf = 0; } - /* Set wake-enable bit */ - if (uart->wk_en && uart->wk_mask) { - v = __raw_readl(uart->wk_en); - v |= uart->wk_mask; - __raw_writel(v, uart->wk_en); - } - - /* Ensure IOPAD wake-enables are set */ - if (cpu_is_omap34xx() && uart->padconf) { - u16 v; - - v = omap_ctrl_readw(uart->padconf); - v |= OMAP3_PADCONF_WAKEUPENABLE0; - omap_ctrl_writew(v, uart->padconf); - } - p->flags |= UPF_SHARE_IRQ; ret = request_irq(p->irq, omap_uart_interrupt, IRQF_SHARED, "serial idle", (void *)uart); @@ -449,54 +480,81 @@ void omap_uart_enable_irqs(int enable) } } -static ssize_t sleep_timeout_show(struct kobject *kobj, - struct kobj_attribute *attr, +static ssize_t sleep_timeout_show(struct device *dev, + struct device_attribute *attr, char *buf) { - return sprintf(buf, "%u\n", sleep_timeout / HZ); + struct platform_device *pdev = container_of(dev, + struct platform_device, dev); + struct omap_uart_state *uart = container_of(pdev, + struct omap_uart_state, pdev); + + return sprintf(buf, "%u\n", uart->timeout / HZ); } -static ssize_t sleep_timeout_store(struct kobject *kobj, - struct kobj_attribute *attr, +static ssize_t sleep_timeout_store(struct device *dev, + struct device_attribute *attr, const char *buf, size_t n) { - struct omap_uart_state *uart; + struct platform_device *pdev = container_of(dev, + struct platform_device, dev); + struct omap_uart_state *uart = container_of(pdev, + struct omap_uart_state, pdev); unsigned int value; if (sscanf(buf, "%u", &value) != 1) { printk(KERN_ERR "sleep_timeout_store: Invalid value\n"); return -EINVAL; } - sleep_timeout = value * HZ; - list_for_each_entry(uart, &uart_list, node) { - uart->timeout = sleep_timeout; - if (uart->timeout) - mod_timer(&uart->timer, jiffies + uart->timeout); - else - /* A zero value means disable timeout feature */ - omap_uart_block_sleep(uart); - } + + uart->timeout = value * HZ; + if (uart->timeout) + mod_timer(&uart->timer, jiffies + uart->timeout); + else + /* A zero value means disable timeout feature */ + omap_uart_block_sleep(uart); + return n; } -static struct kobj_attribute sleep_timeout_attr = - __ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store); - +DEVICE_ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store); +#define DEV_CREATE_FILE(dev, attr) WARN_ON(device_create_file(dev, attr)) #else static inline void omap_uart_idle_init(struct omap_uart_state *uart) {} +#define DEV_CREATE_FILE(dev, attr) #endif /* CONFIG_PM */ -static struct platform_device serial_device = { - .name = "serial8250", - .id = PLAT8250_DEV_PLATFORM, - .dev = { - .platform_data = serial_platform_data, +static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS] = { + { + .pdev = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM, + .dev = { + .platform_data = serial_platform_data0, + }, + }, + }, { + .pdev = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM1, + .dev = { + .platform_data = serial_platform_data1, + }, + }, + }, { + .pdev = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM2, + .dev = { + .platform_data = serial_platform_data2, + }, + }, }, }; void __init omap_serial_init(void) { - int i, err; + int i; const struct omap_uart_config *info; char name[16]; @@ -512,8 +570,10 @@ void __init omap_serial_init(void) return; for (i = 0; i < OMAP_MAX_NR_PORTS; i++) { - struct plat_serial8250_port *p = serial_platform_data + i; struct omap_uart_state *uart = &omap_uart[i]; + struct platform_device *pdev = &uart->pdev; + struct device *dev = &pdev->dev; + struct plat_serial8250_port *p = dev->platform_data; if (!(info->enabled_uarts & (1 << i))) { p->membase = NULL; @@ -549,15 +609,13 @@ void __init omap_serial_init(void) omap_uart_enable_clocks(uart); omap_uart_reset(uart); omap_uart_idle_init(uart); - } - - err = platform_device_register(&serial_device); - -#ifdef CONFIG_PM - if (!err) - err = sysfs_create_file(&serial_device.dev.kobj, - &sleep_timeout_attr.attr); -#endif + if (WARN_ON(platform_device_register(pdev))) + continue; + if ((cpu_is_omap34xx() && uart->padconf) || + (uart->wk_en && uart->wk_mask)) { + device_init_wakeup(dev, true); + DEV_CREATE_FILE(dev, &dev_attr_sleep_timeout); + } + } } - -- GitLab From bcf396c48012a5e4c7ab77be5c40df10d6bdb8ad Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Tue, 30 Jun 2009 21:02:45 -0700 Subject: [PATCH 0836/1342] OMAP2/3/4: UART: allow in-order port traversal Use list_add_tail() when adding discovered UART ports. This is so traversal using list_for_each_entry() will traverse the list in the order they were found. Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/serial.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index 6f35a7e4893..a7421a50410 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -601,7 +601,7 @@ void __init omap_serial_init(void) uart->num = i; p->private_data = uart; uart->p = p; - list_add(&uart->node, &uart_list); + list_add_tail(&uart->node, &uart_list); if (cpu_is_omap44xx()) p->irq += 32; -- GitLab From 60c45ae1107c4ec47d2c84e5984ea59d02b2863d Mon Sep 17 00:00:00 2001 From: Eero Nurkkala Date: Tue, 23 Jun 2009 12:53:29 +0300 Subject: [PATCH 0837/1342] OMAP: PM: CPUfreq: obey min/max settings of policy Use the min/max settings from CPUfreq policy rather than processor defined min/max settings. Without this patch, it's possible to scale frequency outside the current policy range. Signed-off-by: Eero Nurkkala Signed-off-by: Kevin Hilman --- arch/arm/plat-omap/cpu-omap.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/arm/plat-omap/cpu-omap.c b/arch/arm/plat-omap/cpu-omap.c index 843e8af6406..1868c0d8f9b 100644 --- a/arch/arm/plat-omap/cpu-omap.c +++ b/arch/arm/plat-omap/cpu-omap.c @@ -78,10 +78,10 @@ static int omap_target(struct cpufreq_policy *policy, /* Ensure desired rate is within allowed range. Some govenors * (ondemand) will just pass target_freq=0 to get the minimum. */ - if (target_freq < policy->cpuinfo.min_freq) - target_freq = policy->cpuinfo.min_freq; - if (target_freq > policy->cpuinfo.max_freq) - target_freq = policy->cpuinfo.max_freq; + if (target_freq < policy->min) + target_freq = policy->min; + if (target_freq > policy->max) + target_freq = policy->max; freqs.old = omap_getspeed(0); freqs.new = clk_round_rate(mpu_clk, target_freq * 1000) / 1000; -- GitLab From 6c5f80393b107b0c9e2a54b03b65d1880e706655 Mon Sep 17 00:00:00 2001 From: Jouni Hogander Date: Wed, 29 Oct 2008 12:06:04 +0200 Subject: [PATCH 0838/1342] OMAP3: PM: Fix wrong sequence in suspend. Powerdomain previous state is checked after restoring new states in suspend. This patch fixes this problem. Signed-off-by: Jouni Hogander Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index b07efb26de1..488d595d8e4 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -326,7 +326,6 @@ static int omap3_pm_suspend(void) restore: /* Restore next_pwrsts */ list_for_each_entry(pwrst, &pwrst_list, node) { - set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state); state = pwrdm_read_prev_pwrst(pwrst->pwrdm); if (state > pwrst->next_state) { printk(KERN_INFO "Powerdomain (%s) didn't enter " @@ -334,6 +333,7 @@ restore: pwrst->pwrdm->name, pwrst->next_state); ret = -1; } + set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state); } if (ret) printk(KERN_ERR "Could not enter target state in pm_suspend\n"); -- GitLab From 55b6019ae29456e0f1e4087546bf4221c48622a0 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Thu, 4 Jun 2009 15:57:10 -0700 Subject: [PATCH 0839/1342] OMAP: GPIO: clear/restore level/edge detect settings on mask/unmask If IRQ triggering is enabled, it can trigger a pending interrupt even for masked interrupts. Any pending GPIO interrupts can prevent the powerdomain from hitting retention. Problem found, reported and additional review and testing by Chunquiu Wang. Tested-by: Chunquiu Wang Signed-off-by: Kevin Hilman --- arch/arm/plat-omap/gpio.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/plat-omap/gpio.c b/arch/arm/plat-omap/gpio.c index 26b387c1242..77bad14633e 100644 --- a/arch/arm/plat-omap/gpio.c +++ b/arch/arm/plat-omap/gpio.c @@ -1189,6 +1189,7 @@ static void gpio_mask_irq(unsigned int irq) struct gpio_bank *bank = get_irq_chip_data(irq); _set_gpio_irqenable(bank, gpio, 0); + _set_gpio_triggering(bank, get_gpio_index(gpio), IRQ_TYPE_NONE); } static void gpio_unmask_irq(unsigned int irq) @@ -1196,6 +1197,11 @@ static void gpio_unmask_irq(unsigned int irq) unsigned int gpio = irq - IH_GPIO_BASE; struct gpio_bank *bank = get_irq_chip_data(irq); unsigned int irq_mask = 1 << get_gpio_index(gpio); + struct irq_desc *desc = irq_to_desc(irq); + u32 trigger = desc->status & IRQ_TYPE_SENSE_MASK; + + if (trigger) + _set_gpio_triggering(bank, get_gpio_index(gpio), trigger); /* For level-triggered GPIOs, the clearing must be done after * the HW source is cleared, thus after the handler has run */ -- GitLab From 6fd210a9cc398ecbff7bcdbe220651b73b654f56 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Mon, 20 Jul 2009 09:09:23 -0700 Subject: [PATCH 0840/1342] OMAP3: Overo: add missing pen-down GPIO definition Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/board-overo.c | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index dff5528fbfb..e26af837510 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -51,6 +51,7 @@ #define OVERO_GPIO_BT_XGATE 15 #define OVERO_GPIO_W2W_NRESET 16 +#define OVERO_GPIO_PENDOWN 114 #define OVERO_GPIO_BT_NRESET 164 #define OVERO_GPIO_USBH_CPEN 168 #define OVERO_GPIO_USBH_NRESET 183 -- GitLab From f60f785679b507cbeeb03d2db080ab649ac86027 Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Tue, 4 Aug 2009 10:39:03 +0000 Subject: [PATCH 0841/1342] netxen: fix dma mask update calculation Fix dma mask calculation that caps at 63-bit addressing even when firmware advertises full 64-bit support. Signed-off-by: Dhananjay Phadke Signed-off-by: David S. Miller --- drivers/net/netxen/netxen_nic_main.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index 3cd8cfcf627..70c05c4c0ca 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -260,7 +260,7 @@ nx_update_dma_mask(struct netxen_adapter *adapter) change = 0; shift = NXRD32(adapter, CRB_DMA_SHIFT); - if (shift >= 32) + if (shift > 32) return 0; if (NX_IS_REVISION_P3(adapter->ahw.revision_id) && (shift > 9)) @@ -272,7 +272,7 @@ nx_update_dma_mask(struct netxen_adapter *adapter) old_mask = pdev->dma_mask; old_cmask = pdev->dev.coherent_dma_mask; - mask = (1ULL<<(32+shift)) - 1; + mask = DMA_BIT_MASK(32+shift); err = pci_set_dma_mask(pdev, mask); if (err) -- GitLab From 476181cb05c6a3aea3ef42309388e255c934a06f Mon Sep 17 00:00:00 2001 From: Wei Yongjun Date: Tue, 4 Aug 2009 21:44:39 +0000 Subject: [PATCH 0842/1342] dccp: missing destroy of percpu counter variable while unload module percpu counter dccp_orphan_count is init in dccp_init() by percpu_counter_init() while dccp module is loaded, but the destroy of it is missing while dccp module is unloaded. We can get the kernel WARNING about this. Reproduct by the following commands: $ modprobe dccp $ rmmod dccp $ modprobe dccp WARNING: at lib/list_debug.c:26 __list_add+0x27/0x5c() Hardware name: VMware Virtual Platform list_add corruption. next->prev should be prev (c080c0c4), but was (null). (next =ca7188cc). Modules linked in: dccp(+) nfsd lockd nfs_acl auth_rpcgss exportfs sunrpc Pid: 1956, comm: modprobe Not tainted 2.6.31-rc5 #55 Call Trace: [] warn_slowpath_common+0x6a/0x81 [] ? __list_add+0x27/0x5c [] warn_slowpath_fmt+0x29/0x2c [] __list_add+0x27/0x5c [] __percpu_counter_init+0x4d/0x5d [] dccp_init+0x19/0x2ed [dccp] [] do_one_initcall+0x4f/0x111 [] ? dccp_init+0x0/0x2ed [dccp] [] ? notifier_call_chain+0x26/0x48 [] ? __blocking_notifier_call_chain+0x45/0x51 [] sys_init_module+0xac/0x1bd [] sysenter_do_call+0x12/0x22 Signed-off-by: Wei Yongjun Acked-by: Eric Dumazet Signed-off-by: David S. Miller --- net/dccp/proto.c | 1 + 1 file changed, 1 insertion(+) diff --git a/net/dccp/proto.c b/net/dccp/proto.c index 94ca8eaace7..6294f57162b 100644 --- a/net/dccp/proto.c +++ b/net/dccp/proto.c @@ -1159,6 +1159,7 @@ static void __exit dccp_fini(void) kmem_cache_destroy(dccp_hashinfo.bind_bucket_cachep); dccp_ackvec_exit(); dccp_sysctl_exit(); + percpu_counter_destroy(&dccp_orphan_count); } module_init(dccp_init); -- GitLab From 9c9fe1f841745184bbc5460c6f3909fded3b929b Mon Sep 17 00:00:00 2001 From: Eric Anholt Date: Mon, 3 Aug 2009 16:09:16 -0700 Subject: [PATCH 0843/1342] drm/i915: Use our own workqueue to avoid wedging the system along with the GPU. Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/i915_dma.c | 15 +++++++++++++-- drivers/gpu/drm/i915/i915_drv.h | 1 + drivers/gpu/drm/i915/i915_gem.c | 4 ++-- drivers/gpu/drm/i915/i915_irq.c | 5 +++-- 4 files changed, 19 insertions(+), 6 deletions(-) diff --git a/drivers/gpu/drm/i915/i915_dma.c b/drivers/gpu/drm/i915/i915_dma.c index 8c4783180bf..50d1f782768 100644 --- a/drivers/gpu/drm/i915/i915_dma.c +++ b/drivers/gpu/drm/i915/i915_dma.c @@ -1186,6 +1186,13 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags) if (ret) goto out_iomapfree; + dev_priv->wq = create_workqueue("i915"); + if (dev_priv->wq == NULL) { + DRM_ERROR("Failed to create our workqueue.\n"); + ret = -ENOMEM; + goto out_iomapfree; + } + /* enable GEM by default */ dev_priv->has_gem = 1; @@ -1211,7 +1218,7 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags) if (!I915_NEED_GFX_HWS(dev)) { ret = i915_init_phys_hws(dev); if (ret != 0) - goto out_iomapfree; + goto out_workqueue_free; } i915_get_mem_freq(dev); @@ -1245,7 +1252,7 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags) ret = i915_load_modeset_init(dev, prealloc_size, agp_size); if (ret < 0) { DRM_ERROR("failed to init modeset\n"); - goto out_rmmap; + goto out_workqueue_free; } } @@ -1256,6 +1263,8 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags) return 0; +out_workqueue_free: + destroy_workqueue(dev_priv->wq); out_iomapfree: io_mapping_free(dev_priv->mm.gtt_mapping); out_rmmap: @@ -1269,6 +1278,8 @@ int i915_driver_unload(struct drm_device *dev) { struct drm_i915_private *dev_priv = dev->dev_private; + destroy_workqueue(dev_priv->wq); + io_mapping_free(dev_priv->mm.gtt_mapping); if (dev_priv->mm.gtt_mtrr >= 0) { mtrr_del(dev_priv->mm.gtt_mtrr, dev->agp->base, diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h index 5f3a259d95e..7537f57d8a8 100644 --- a/drivers/gpu/drm/i915/i915_drv.h +++ b/drivers/gpu/drm/i915/i915_drv.h @@ -231,6 +231,7 @@ typedef struct drm_i915_private { spinlock_t error_lock; struct drm_i915_error_state *first_error; struct work_struct error_work; + struct workqueue_struct *wq; /* Register state */ u8 saveLBB; diff --git a/drivers/gpu/drm/i915/i915_gem.c b/drivers/gpu/drm/i915/i915_gem.c index 5bf420378b6..140bee142fc 100644 --- a/drivers/gpu/drm/i915/i915_gem.c +++ b/drivers/gpu/drm/i915/i915_gem.c @@ -1570,7 +1570,7 @@ i915_add_request(struct drm_device *dev, struct drm_file *file_priv, } if (was_empty && !dev_priv->mm.suspended) - schedule_delayed_work(&dev_priv->mm.retire_work, HZ); + queue_delayed_work(dev_priv->wq, &dev_priv->mm.retire_work, HZ); return seqno; } @@ -1719,7 +1719,7 @@ i915_gem_retire_work_handler(struct work_struct *work) i915_gem_retire_requests(dev); if (!dev_priv->mm.suspended && !list_empty(&dev_priv->mm.request_list)) - schedule_delayed_work(&dev_priv->mm.retire_work, HZ); + queue_delayed_work(dev_priv->wq, &dev_priv->mm.retire_work, HZ); mutex_unlock(&dev->struct_mutex); } diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c index f340b3fd54e..83aee80e77a 100644 --- a/drivers/gpu/drm/i915/i915_irq.c +++ b/drivers/gpu/drm/i915/i915_irq.c @@ -482,7 +482,7 @@ static void i915_handle_error(struct drm_device *dev) I915_WRITE(IIR, I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT); } - schedule_work(&dev_priv->error_work); + queue_work(dev_priv->wq, &dev_priv->error_work); } irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS) @@ -560,7 +560,8 @@ irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS) DRM_DEBUG("hotplug event received, stat 0x%08x\n", hotplug_status); if (hotplug_status & dev_priv->hotplug_supported_mask) - schedule_work(&dev_priv->hotplug_work); + queue_work(dev_priv->wq, + &dev_priv->hotplug_work); I915_WRITE(PORT_HOTPLUG_STAT, hotplug_status); I915_READ(PORT_HOTPLUG_STAT); -- GitLab From 819e0064634f580ab618189e657ea58341d214b7 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Sun, 26 Jul 2009 00:50:38 +0200 Subject: [PATCH 0844/1342] drm/i915: Fix read outside array bounds in restoring the SWF10 range. dev_priv->saveSWF1 is a 16 element array, but this reads up to index 22, and restored values from the wrong registers. Signed-off-by: Roel Kluin Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/i915_suspend.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/gpu/drm/i915/i915_suspend.c b/drivers/gpu/drm/i915/i915_suspend.c index 9e1d16e5c3e..1d04e1904ac 100644 --- a/drivers/gpu/drm/i915/i915_suspend.c +++ b/drivers/gpu/drm/i915/i915_suspend.c @@ -598,7 +598,7 @@ int i915_restore_state(struct drm_device *dev) for (i = 0; i < 16; i++) { I915_WRITE(SWF00 + (i << 2), dev_priv->saveSWF0[i]); - I915_WRITE(SWF10 + (i << 2), dev_priv->saveSWF1[i+7]); + I915_WRITE(SWF10 + (i << 2), dev_priv->saveSWF1[i]); } for (i = 0; i < 3; i++) I915_WRITE(SWF30 + (i << 2), dev_priv->saveSWF2[i]); -- GitLab From cf39c4c572dc54adbdf8933d1e6cd87ee94d8fc0 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Mon, 27 Jul 2009 08:03:18 -0700 Subject: [PATCH 0845/1342] phonet: phonet_device_get() fix MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit net/phonet/pn_dev.c: In function `phonet_device_get': net/phonet/pn_dev.c:99: warning: 'dev' might be used uninitialized in this function Signed-off-by: Eric Dumazet Acked-by: Rémi Denis-Courmont Signed-off-by: David S. Miller --- net/phonet/pn_dev.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/phonet/pn_dev.c b/net/phonet/pn_dev.c index b0d6ddd82a9..c2b77a69869 100644 --- a/net/phonet/pn_dev.c +++ b/net/phonet/pn_dev.c @@ -96,7 +96,7 @@ struct net_device *phonet_device_get(struct net *net) { struct phonet_device_list *pndevs = phonet_device_list(net); struct phonet_device *pnd; - struct net_device *dev; + struct net_device *dev = NULL; spin_lock_bh(&pndevs->lock); list_for_each_entry(pnd, &pndevs->list, list) { -- GitLab From 0a51810aa058a0a4ac76dd6f87f4d10bee774e2e Mon Sep 17 00:00:00 2001 From: Andrew Victor Date: Tue, 4 Aug 2009 19:55:56 +0100 Subject: [PATCH 0846/1342] ARM: 5637/1: [KS8695] Don't reference CLOCK_TICK_RATE in drivers Stop referencing CLOCK_TICK_RATE in the KS8695 drivers, rather refer to a KS8695_CLOCK_RATE. Issue pointed out by Russell King on arm-linux-kernel mailing list. Signed-off-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mach-ks8695/include/mach/hardware.h | 5 +++++ arch/arm/mach-ks8695/include/mach/timex.h | 5 +++-- drivers/serial/serial_ks8695.c | 2 +- drivers/watchdog/ks8695_wdt.c | 4 ++-- 4 files changed, 11 insertions(+), 5 deletions(-) diff --git a/arch/arm/mach-ks8695/include/mach/hardware.h b/arch/arm/mach-ks8695/include/mach/hardware.h index 1d640d075b7..e0f911d9e02 100644 --- a/arch/arm/mach-ks8695/include/mach/hardware.h +++ b/arch/arm/mach-ks8695/include/mach/hardware.h @@ -16,6 +16,11 @@ #include +/* + * Clocks are derived from MCLK, which is 25Mhz + */ +#define KS8695_CLOCK_RATE 25000000 + /* * Physical RAM address. */ diff --git a/arch/arm/mach-ks8695/include/mach/timex.h b/arch/arm/mach-ks8695/include/mach/timex.h index 4682e350369..10f716371bd 100644 --- a/arch/arm/mach-ks8695/include/mach/timex.h +++ b/arch/arm/mach-ks8695/include/mach/timex.h @@ -14,7 +14,8 @@ #ifndef __ASM_ARCH_TIMEX_H #define __ASM_ARCH_TIMEX_H -/* timers are derived from MCLK, which is 25MHz */ -#define CLOCK_TICK_RATE 25000000 +#include + +#define CLOCK_TICK_RATE KS8695_CLOCK_RATE #endif diff --git a/drivers/serial/serial_ks8695.c b/drivers/serial/serial_ks8695.c index 998e89dc5aa..e0665630e4d 100644 --- a/drivers/serial/serial_ks8695.c +++ b/drivers/serial/serial_ks8695.c @@ -549,7 +549,7 @@ static struct uart_port ks8695uart_ports[SERIAL_KS8695_NR] = { .mapbase = KS8695_UART_VA, .iotype = SERIAL_IO_MEM, .irq = KS8695_IRQ_UART_TX, - .uartclk = CLOCK_TICK_RATE * 16, + .uartclk = KS8695_CLOCK_RATE * 16, .fifosize = 16, .ops = &ks8695uart_pops, .flags = ASYNC_BOOT_AUTOCONF, diff --git a/drivers/watchdog/ks8695_wdt.c b/drivers/watchdog/ks8695_wdt.c index 00b03eb43bf..e1c82769b08 100644 --- a/drivers/watchdog/ks8695_wdt.c +++ b/drivers/watchdog/ks8695_wdt.c @@ -66,7 +66,7 @@ static inline void ks8695_wdt_stop(void) static inline void ks8695_wdt_start(void) { unsigned long tmcon; - unsigned long tval = wdt_time * CLOCK_TICK_RATE; + unsigned long tval = wdt_time * KS8695_CLOCK_RATE; spin_lock(&ks8695_lock); /* disable timer0 */ @@ -103,7 +103,7 @@ static inline void ks8695_wdt_reload(void) static int ks8695_wdt_settimeout(int new_time) { /* - * All counting occurs at SLOW_CLOCK / 128 = 0.256 Hz + * All counting occurs at KS8695_CLOCK_RATE / 128 = 0.256 Hz * * Since WDV is a 16-bit counter, the maximum period is * 65536 / 0.256 = 256 seconds. -- GitLab From 65a5053b764a42d33b334ba55810bb5b56eb92df Mon Sep 17 00:00:00 2001 From: Hartley Sweeten Date: Tue, 4 Aug 2009 23:20:45 +0100 Subject: [PATCH 0847/1342] ARM: 5638/1: arch/arm/kernel/signal.c: use correct address space for CRUNCH preserve_crunch_context() calls __copy_to_user() which expects the destination address to be in __user space. setup_sigframe() properly passes the destination address. restore_crunch_context() calls __copy_from_user() which expects the source address to be in __user space. restore_sigframe() properly passes the source address. This fixes {preserve/restore}_crunch_context() to accept the address as __user space and resolves the following sparse warnings: arch/arm/kernel/signal.c:146:31: warning: incorrect type in argument 1 (different address spaces) expected void [noderef] *to got struct crunch_sigframe *frame arch/arm/kernel/signal.c:156:38: warning: incorrect type in argument 2 (different address spaces) expected void const [noderef] *from got struct crunch_sigframe *frame arch/arm/kernel/signal.c:250:48: warning: incorrect type in argument 1 (different address spaces) expected struct crunch_sigframe *frame got struct crunch_sigframe [noderef] * arch/arm/kernel/signal.c:365:49: warning: incorrect type in argument 1 (different address spaces) expected struct crunch_sigframe *frame got struct crunch_sigframe [noderef] * Signed-off-by: H Hartley Sweeten Signed-off-by: Russell King --- arch/arm/kernel/signal.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/kernel/signal.c b/arch/arm/kernel/signal.c index 93bb4247b7e..f6bc5d44278 100644 --- a/arch/arm/kernel/signal.c +++ b/arch/arm/kernel/signal.c @@ -133,7 +133,7 @@ sys_sigaction(int sig, const struct old_sigaction __user *act, } #ifdef CONFIG_CRUNCH -static int preserve_crunch_context(struct crunch_sigframe *frame) +static int preserve_crunch_context(struct crunch_sigframe __user *frame) { char kbuf[sizeof(*frame) + 8]; struct crunch_sigframe *kframe; @@ -146,7 +146,7 @@ static int preserve_crunch_context(struct crunch_sigframe *frame) return __copy_to_user(frame, kframe, sizeof(*frame)); } -static int restore_crunch_context(struct crunch_sigframe *frame) +static int restore_crunch_context(struct crunch_sigframe __user *frame) { char kbuf[sizeof(*frame) + 8]; struct crunch_sigframe *kframe; -- GitLab From c0c60c4b9ab45bb02b20796401dd6a90770fd0ee Mon Sep 17 00:00:00 2001 From: Hartley Sweeten Date: Tue, 4 Aug 2009 23:38:06 +0100 Subject: [PATCH 0848/1342] ARM: 5639/1: arm: clkdev.c should include should be included to get the base API prototypes. This fixes the following sparse warnings: arch/arm/common/clkdev.c:65:12: warning: symbol 'clk_get_sys' was not declared. Should it be static? arch/arm/common/clkdev.c:79:12: warning: symbol 'clk_get' was not declared. Should it be static? arch/arm/common/clkdev.c:87:6: warning: symbol 'clk_put' was not declared. Should it be static? Signed-off-by: H Hartley Sweeten Signed-off-by: Russell King --- arch/arm/common/clkdev.c | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/common/clkdev.c b/arch/arm/common/clkdev.c index f37afd9422f..aae5bc01acc 100644 --- a/arch/arm/common/clkdev.c +++ b/arch/arm/common/clkdev.c @@ -17,6 +17,7 @@ #include #include #include +#include #include #include -- GitLab From 0f2541d299d233eddddee4345795e0c46264fd56 Mon Sep 17 00:00:00 2001 From: Steven Rostedt Date: Wed, 5 Aug 2009 12:02:48 -0400 Subject: [PATCH 0849/1342] ring-buffer: fix check of try_to_discard result The function ring_buffer_discard_commit inversed the code path of the result of try_to_discard. It should skip incrementing the entry counter if try_to_discard succeeded. But instead, it increments the entry conder if it succeeded to discard, and does not increment it if it fails. The result of this bug is that filtering will make the stat counters incorrect. Signed-off-by: Steven Rostedt --- kernel/trace/ring_buffer.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/trace/ring_buffer.c b/kernel/trace/ring_buffer.c index bf27bb7a63e..2fd1752f0c8 100644 --- a/kernel/trace/ring_buffer.c +++ b/kernel/trace/ring_buffer.c @@ -1785,7 +1785,7 @@ void ring_buffer_discard_commit(struct ring_buffer *buffer, */ RB_WARN_ON(buffer, !local_read(&cpu_buffer->committing)); - if (!rb_try_to_discard(cpu_buffer, event)) + if (rb_try_to_discard(cpu_buffer, event)) goto out; /* -- GitLab From 464e85eb0e63096bd52e4c3e2a6fb8357fb95828 Mon Sep 17 00:00:00 2001 From: Steven Rostedt Date: Wed, 5 Aug 2009 15:26:37 -0400 Subject: [PATCH 0850/1342] ring-buffer: do not disable ring buffer on oops_in_progress The commit: commit e0fdace10e75dac67d906213b780ff1b1a4cc360 Author: David Miller Date: Fri Aug 1 01:11:22 2008 -0700 debug_locks: set oops_in_progress if we will log messages. Otherwise lock debugging messages on runqueue locks can deadlock the system due to the wakeups performed by printk(). Signed-off-by: David S. Miller Signed-off-by: Ingo Molnar Will permanently set oops_in_progress on any lockdep failure. When this triggers it will cause any read from the ring buffer to permanently disable the ring buffer (not to mention no locking of printk). This patch removes the check. It keeps the print in NMI which makes sense. This is probably OK, since the ring buffer should not cause something to set oops_in_progress anyway. Signed-off-by: Steven Rostedt --- kernel/trace/ring_buffer.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/trace/ring_buffer.c b/kernel/trace/ring_buffer.c index 2fd1752f0c8..2606cee433d 100644 --- a/kernel/trace/ring_buffer.c +++ b/kernel/trace/ring_buffer.c @@ -2486,7 +2486,7 @@ static inline int rb_ok_to_lock(void) * buffer too. A one time deal is all you get from reading * the ring buffer from an NMI. */ - if (likely(!in_nmi() && !oops_in_progress)) + if (likely(!in_nmi())) return 1; tracing_off_permanent(); -- GitLab From 3f6e968ef4e1d8d93d8a8505461b0e50a9e97ad8 Mon Sep 17 00:00:00 2001 From: Steven Rostedt Date: Wed, 5 Aug 2009 22:00:14 -0400 Subject: [PATCH 0851/1342] tracing: do not use functions starting with .L in recordmcount.pl On Wed, 5 Aug 2009, Ingo Molnar wrote: > * Dave Airlie wrote: > > > Hey, > > > > So I spent 3-4 hrs today (I'm stupid yes) tracking down a .o > > breakage by blaming rawhide gcc/binutils as I was using make > > V=1and seeing only the compiler chain running, > > Hm, is this that powerpc related build bug you just reported? Well we tracked it down and it is powerpc64 specific. Seems that in drivers/hwmon/lm93.c there's a function called: LM93_IN_FROM_REG() But PPC64 has function descriptors and the real function names (the ones you see in objdump) start with a '.'. Thus this in objdump you have: Disassembly of section .text: 0000000000000000 <.LM93_IN_FROM_REG>: 0: 7c 08 02 a6 mflr r0 4: fb 81 ff e0 std r28,-32(r1) The function name used is .LM93_IN_FROM_REG. But gcc considers symbols that start with ".L" as a special symbol that is used inside the assembly stage. The nm passed into recordmcount uses the --synthetic option which shows the ".L" symbols (my runs outside of the build did not include the --synthetic option, so my older patch worked). We see the function as a local. Now to capture all the locations that use "mcount" we need to have a reference to link into the object file a list of mcount callers. We need a reference that will not disappear. We try to use a global function and if that does not work, we use a local function as a reference. But to relink the section back into the object, we need to make it global. In this case, we run objcopy using --globalize-symbol and --localize-symbol to convert the symbol into a global symbol, link the mcount list, then convert it back to a local symbol. This works great except for this case. .L* symbols can not be converted into a global symbol, and the mcount section referencing it will remain unresolved. Reported-by: Dave Airlie LKML-Reference: Signed-off-by: Steven Rostedt --- scripts/recordmcount.pl | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/scripts/recordmcount.pl b/scripts/recordmcount.pl index d29baa2e063..4889c44d71b 100755 --- a/scripts/recordmcount.pl +++ b/scripts/recordmcount.pl @@ -414,7 +414,10 @@ while () { $offset = hex $1; } else { # if we already have a function, and this is weak, skip it - if (!defined($ref_func) && !defined($weak{$text})) { + if (!defined($ref_func) && !defined($weak{$text}) && + # PPC64 can have symbols that start with .L and + # gcc considers these special. Don't use them! + $text !~ /^\.L/) { $ref_func = $text; $offset = hex $1; } -- GitLab From b4adbb4ddf63091f48668e7ff1b9b0f6f84d4b40 Mon Sep 17 00:00:00 2001 From: Pascal Terjan Date: Wed, 5 Aug 2009 04:11:39 +0000 Subject: [PATCH 0852/1342] Add IDs for 3C905B-TX Fast Etherlink XL PCI We found this old card which was not supported, and physically looks similar to the other 3C905B we have (9055). After adding the IDs it seems to work fine (MII report, dhcp, scp, ...) Acked-by: Steffen Klassert Signed-off-by: David S. Miller --- drivers/net/3c59x.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/net/3c59x.c b/drivers/net/3c59x.c index c2041685094..45675889850 100644 --- a/drivers/net/3c59x.c +++ b/drivers/net/3c59x.c @@ -235,6 +235,7 @@ enum vortex_chips { CH_3C900B_FL, CH_3C905_1, CH_3C905_2, + CH_3C905B_TX, CH_3C905B_1, CH_3C905B_2, @@ -307,6 +308,8 @@ static struct vortex_chip_info { PCI_USES_MASTER, IS_BOOMERANG|HAS_MII|EEPROM_RESET, 64, }, {"3c905 Boomerang 100baseT4", PCI_USES_MASTER, IS_BOOMERANG|HAS_MII|EEPROM_RESET, 64, }, + {"3C905B-TX Fast Etherlink XL PCI", + PCI_USES_MASTER, IS_CYCLONE|HAS_NWAY|HAS_HWCKSM|EXTRA_PREAMBLE, 128, }, {"3c905B Cyclone 100baseTx", PCI_USES_MASTER, IS_CYCLONE|HAS_NWAY|HAS_HWCKSM|EXTRA_PREAMBLE, 128, }, @@ -389,6 +392,7 @@ static struct pci_device_id vortex_pci_tbl[] = { { 0x10B7, 0x900A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CH_3C900B_FL }, { 0x10B7, 0x9050, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CH_3C905_1 }, { 0x10B7, 0x9051, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CH_3C905_2 }, + { 0x10B7, 0x9054, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CH_3C905B_TX }, { 0x10B7, 0x9055, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CH_3C905B_1 }, { 0x10B7, 0x9058, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CH_3C905B_2 }, -- GitLab From 1bbf20835c4e088667a090ce6523a0f70b62dc76 Mon Sep 17 00:00:00 2001 From: Darren Hart Date: Wed, 5 Aug 2009 12:05:21 -0700 Subject: [PATCH 0853/1342] rtmutex: Avoid deadlock in rt_mutex_start_proxy_lock() In the event of a lock steal or owner died, rt_mutex_start_proxy_lock() will give the rt_mutex to the waiting task, but it fails to release the wait_lock. This leads to subsequent deadlocks when other tasks try to acquire the rt_mutex. I also removed a few extra blank lines that really spaced this routine out. I must have been high on the \n when I wrote this originally... Signed-off-by: Darren Hart Cc: Peter Zijlstra Cc: Steven Rostedt Cc: Dinakar Guniguntala Cc: John Stultz LKML-Reference: <4A79D7F1.4000405@us.ibm.com> Signed-off-by: Ingo Molnar --- kernel/rtmutex.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/kernel/rtmutex.c b/kernel/rtmutex.c index fcd107a78c5..29bd4baf9e7 100644 --- a/kernel/rtmutex.c +++ b/kernel/rtmutex.c @@ -1039,16 +1039,14 @@ int rt_mutex_start_proxy_lock(struct rt_mutex *lock, if (!rt_mutex_owner(lock) || try_to_steal_lock(lock, task)) { /* We got the lock for task. */ debug_rt_mutex_lock(lock); - rt_mutex_set_owner(lock, task, 0); - + spin_unlock(&lock->wait_lock); rt_mutex_deadlock_account_lock(lock, task); return 1; } ret = task_blocks_on_rt_mutex(lock, waiter, task, detect_deadlock); - if (ret && !waiter->task) { /* * Reset the return value. We might have -- GitLab From af6af30c0fcd77e621638e53ef8b176bca8bd3b4 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Wed, 5 Aug 2009 20:41:04 +0200 Subject: [PATCH 0854/1342] ftrace: Fix perf-tracepoint OOPS Not all tracepoints are created equal, in specific the ftrace tracepoints are created with TRACE_EVENT_FORMAT() which does not generate the needed bits to tie them into perf counters. For those events, don't create the 'id' file and fail ->profile_enable when their ID is specified through other means. Reported-by: Chris Mason Signed-off-by: Peter Zijlstra Cc: Steven Rostedt LKML-Reference: <1249497664.5890.4.camel@laptop> [ v2: fix build error in the !CONFIG_EVENT_PROFILE case ] Signed-off-by: Ingo Molnar --- include/linux/ftrace_event.h | 8 +++----- kernel/trace/trace_event_profile.c | 2 +- kernel/trace/trace_events.c | 2 +- 3 files changed, 5 insertions(+), 7 deletions(-) diff --git a/include/linux/ftrace_event.h b/include/linux/ftrace_event.h index 5c093ffc655..d7cd193c227 100644 --- a/include/linux/ftrace_event.h +++ b/include/linux/ftrace_event.h @@ -119,11 +119,9 @@ struct ftrace_event_call { void *filter; void *mod; -#ifdef CONFIG_EVENT_PROFILE - atomic_t profile_count; - int (*profile_enable)(struct ftrace_event_call *); - void (*profile_disable)(struct ftrace_event_call *); -#endif + atomic_t profile_count; + int (*profile_enable)(struct ftrace_event_call *); + void (*profile_disable)(struct ftrace_event_call *); }; #define MAX_FILTER_PRED 32 diff --git a/kernel/trace/trace_event_profile.c b/kernel/trace/trace_event_profile.c index 5b5895afecf..11ba5bb4ed0 100644 --- a/kernel/trace/trace_event_profile.c +++ b/kernel/trace/trace_event_profile.c @@ -14,7 +14,7 @@ int ftrace_profile_enable(int event_id) mutex_lock(&event_mutex); list_for_each_entry(event, &ftrace_events, list) { - if (event->id == event_id) { + if (event->id == event_id && event->profile_enable) { ret = event->profile_enable(event); break; } diff --git a/kernel/trace/trace_events.c b/kernel/trace/trace_events.c index 23d2972b22d..e75276a49cf 100644 --- a/kernel/trace/trace_events.c +++ b/kernel/trace/trace_events.c @@ -940,7 +940,7 @@ event_create_dir(struct ftrace_event_call *call, struct dentry *d_events, entry = trace_create_file("enable", 0644, call->dir, call, enable); - if (call->id) + if (call->id && call->profile_enable) entry = trace_create_file("id", 0444, call->dir, call, id); -- GitLab From 985fe845aea9cd56fd351800302270444556e45a Mon Sep 17 00:00:00 2001 From: Jerome Glisse Date: Wed, 29 Jul 2009 18:55:53 +0200 Subject: [PATCH 0855/1342] drm/radeon/kms: Fix caching mode selection for GTT object GTT object can either be cached,uncached or wc just let core ttm pick the best mode according to how the bo driver and GTT memory type was initialized. Signed-off-by: Jerome Glisse Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_object.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c index dd9ac2fed6d..e98cae3bf4a 100644 --- a/drivers/gpu/drm/radeon/radeon_object.c +++ b/drivers/gpu/drm/radeon/radeon_object.c @@ -106,7 +106,7 @@ static inline uint32_t radeon_object_flags_from_domain(uint32_t domain) flags |= TTM_PL_FLAG_VRAM | TTM_PL_FLAG_WC | TTM_PL_FLAG_UNCACHED; } if (domain & RADEON_GEM_DOMAIN_GTT) { - flags |= TTM_PL_FLAG_TT | TTM_PL_FLAG_WC | TTM_PL_FLAG_UNCACHED; + flags |= TTM_PL_FLAG_TT | TTM_PL_MASK_CACHING; } if (domain & RADEON_GEM_DOMAIN_CPU) { flags |= TTM_PL_FLAG_SYSTEM | TTM_PL_MASK_CACHING; -- GitLab From 194934785a846e0a7b1b674b7b475a9d0125d2f8 Mon Sep 17 00:00:00 2001 From: TJ Date: Mon, 3 Aug 2009 13:39:09 -0700 Subject: [PATCH 0856/1342] Input: wistron_btns - support Prestigio Wifi RF kill button The Prestigio 157, an old no-name clone laptop uses input keys very similar to the Wistron 1557/MS2141 with the addition of BIOS-controlled wireless radio frequency kill switch. This patch adds support for the RF kill switch control and adds manual identification of the model. The Prestigio does not expose any recognisable identity via dmidecode and so requires manual selection at module init using force=1 keymap=prestigio Signed-off-by: TJ Signed-off-by: Dmitry Torokhov --- drivers/input/misc/wistron_btns.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/drivers/input/misc/wistron_btns.c b/drivers/input/misc/wistron_btns.c index 26e17a9a22e..27ee976eb54 100644 --- a/drivers/input/misc/wistron_btns.c +++ b/drivers/input/misc/wistron_btns.c @@ -611,6 +611,20 @@ static struct key_entry keymap_wistron_generic[] __initdata = { { KE_END, 0 } }; +static struct key_entry keymap_prestigio[] __initdata = { + { KE_KEY, 0x11, {KEY_PROG1} }, + { KE_KEY, 0x12, {KEY_PROG2} }, + { KE_WIFI, 0x30 }, + { KE_KEY, 0x22, {KEY_REWIND} }, + { KE_KEY, 0x23, {KEY_FORWARD} }, + { KE_KEY, 0x24, {KEY_PLAYPAUSE} }, + { KE_KEY, 0x25, {KEY_STOPCD} }, + { KE_KEY, 0x31, {KEY_MAIL} }, + { KE_KEY, 0x36, {KEY_WWW} }, + { KE_END, 0 } +}; + + /* * If your machine is not here (which is currently rather likely), please send * a list of buttons and their key codes (reported when loading this module @@ -971,6 +985,8 @@ static int __init select_keymap(void) if (keymap_name != NULL) { if (strcmp (keymap_name, "1557/MS2141") == 0) keymap = keymap_wistron_ms2141; + else if (strcmp (keymap_name, "prestigio") == 0) + keymap = keymap_prestigio; else if (strcmp (keymap_name, "generic") == 0) keymap = keymap_wistron_generic; else { -- GitLab From d82f1c35348cebe2fb2d4a4d31ce0ab0769e3d93 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Wed, 5 Aug 2009 01:24:41 -0700 Subject: [PATCH 0857/1342] Input: matrix_keypad - make matrix keymap size dynamic Remove assumption on the shift and size of rows/columns form matrix_keypad driver. Signed-off-by: Eric Miao Signed-off-by: Dmitry Torokhov --- drivers/input/keyboard/matrix_keypad.c | 18 +++++++++--------- include/linux/input/matrix_keypad.h | 13 +++++++------ 2 files changed, 16 insertions(+), 15 deletions(-) diff --git a/drivers/input/keyboard/matrix_keypad.c b/drivers/input/keyboard/matrix_keypad.c index e9b2e7cb05b..541b981ff07 100644 --- a/drivers/input/keyboard/matrix_keypad.c +++ b/drivers/input/keyboard/matrix_keypad.c @@ -27,6 +27,7 @@ struct matrix_keypad { const struct matrix_keypad_platform_data *pdata; struct input_dev *input_dev; unsigned short *keycodes; + unsigned int row_shift; uint32_t last_key_state[MATRIX_MAX_COLS]; struct delayed_work work; @@ -136,7 +137,7 @@ static void matrix_keypad_scan(struct work_struct *work) if ((bits_changed & (1 << row)) == 0) continue; - code = (row << 4) + col; + code = MATRIX_SCAN_CODE(row, col, keypad->row_shift); input_event(input_dev, EV_MSC, MSC_SCAN, code); input_report_key(input_dev, keypad->keycodes[code], @@ -317,6 +318,7 @@ static int __devinit matrix_keypad_probe(struct platform_device *pdev) struct matrix_keypad *keypad; struct input_dev *input_dev; unsigned short *keycodes; + unsigned int row_shift; int i; int err; @@ -332,14 +334,11 @@ static int __devinit matrix_keypad_probe(struct platform_device *pdev) return -EINVAL; } - if (!keymap_data->max_keymap_size) { - dev_err(&pdev->dev, "invalid keymap data supplied\n"); - return -EINVAL; - } + row_shift = get_count_order(pdata->num_col_gpios); keypad = kzalloc(sizeof(struct matrix_keypad), GFP_KERNEL); - keycodes = kzalloc(keymap_data->max_keymap_size * - sizeof(keypad->keycodes), + keycodes = kzalloc((pdata->num_row_gpios << row_shift) * + sizeof(*keycodes), GFP_KERNEL); input_dev = input_allocate_device(); if (!keypad || !keycodes || !input_dev) { @@ -350,6 +349,7 @@ static int __devinit matrix_keypad_probe(struct platform_device *pdev) keypad->input_dev = input_dev; keypad->pdata = pdata; keypad->keycodes = keycodes; + keypad->row_shift = row_shift; keypad->stopped = true; INIT_DELAYED_WORK(&keypad->work, matrix_keypad_scan); spin_lock_init(&keypad->lock); @@ -363,7 +363,7 @@ static int __devinit matrix_keypad_probe(struct platform_device *pdev) input_dev->keycode = keycodes; input_dev->keycodesize = sizeof(*keycodes); - input_dev->keycodemax = keymap_data->max_keymap_size; + input_dev->keycodemax = pdata->num_row_gpios << keypad->row_shift; for (i = 0; i < keymap_data->keymap_size; i++) { unsigned int key = keymap_data->keymap[i]; @@ -371,7 +371,7 @@ static int __devinit matrix_keypad_probe(struct platform_device *pdev) unsigned int col = KEY_COL(key); unsigned short code = KEY_VAL(key); - keycodes[(row << 4) + col] = code; + keycodes[MATRIX_SCAN_CODE(row, col, row_shift)] = code; __set_bit(code, input_dev->keybit); } __clear_bit(KEY_RESERVED, input_dev->keybit); diff --git a/include/linux/input/matrix_keypad.h b/include/linux/input/matrix_keypad.h index 7964516c695..15d5903af2d 100644 --- a/include/linux/input/matrix_keypad.h +++ b/include/linux/input/matrix_keypad.h @@ -15,12 +15,13 @@ #define KEY_COL(k) (((k) >> 16) & 0xff) #define KEY_VAL(k) ((k) & 0xffff) +#define MATRIX_SCAN_CODE(row, col, row_shift) (((row) << (row_shift)) + (col)) + /** * struct matrix_keymap_data - keymap for matrix keyboards * @keymap: pointer to array of uint32 values encoded with KEY() macro * representing keymap * @keymap_size: number of entries (initialized) in this keymap - * @max_keymap_size: maximum size of keymap supported by the device * * This structure is supposed to be used by platform code to supply * keymaps to drivers that implement matrix-like keypads/keyboards. @@ -28,14 +29,13 @@ struct matrix_keymap_data { const uint32_t *keymap; unsigned int keymap_size; - unsigned int max_keymap_size; }; /** * struct matrix_keypad_platform_data - platform-dependent keypad data * @keymap_data: pointer to &matrix_keymap_data - * @row_gpios: array of gpio numbers reporesenting rows - * @col_gpios: array of gpio numbers reporesenting colums + * @row_gpios: pointer to array of gpio numbers representing rows + * @col_gpios: pointer to array of gpio numbers reporesenting colums * @num_row_gpios: actual number of row gpios used by device * @num_col_gpios: actual number of col gpios used by device * @col_scan_delay_us: delay, measured in microseconds, that is @@ -48,8 +48,9 @@ struct matrix_keymap_data { struct matrix_keypad_platform_data { const struct matrix_keymap_data *keymap_data; - unsigned int row_gpios[MATRIX_MAX_ROWS]; - unsigned int col_gpios[MATRIX_MAX_COLS]; + const unsigned int *row_gpios; + const unsigned int *col_gpios; + unsigned int num_row_gpios; unsigned int num_col_gpios; -- GitLab From 45a41d147a3a31bb218201b0dd70cfe4e9ed5105 Mon Sep 17 00:00:00 2001 From: Dmitry Eremin-Solenikov Date: Sun, 2 Aug 2009 14:12:01 +0400 Subject: [PATCH 0858/1342] af_ieee802154: fix ioctl processing fix two errors in ioctl processing: 1) if the ioctl isn't supported one should return -ENOIOCTLCMD 2) don't call ndo_do_ioctl if the device doesn't provide it Signed-off-by: Dmitry Eremin-Solenikov --- net/ieee802154/af_ieee802154.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) diff --git a/net/ieee802154/af_ieee802154.c b/net/ieee802154/af_ieee802154.c index 3bb6bdb1dac..af661805b9f 100644 --- a/net/ieee802154/af_ieee802154.c +++ b/net/ieee802154/af_ieee802154.c @@ -136,7 +136,7 @@ static int ieee802154_dev_ioctl(struct sock *sk, struct ifreq __user *arg, unsigned int cmd) { struct ifreq ifr; - int ret = -EINVAL; + int ret = -ENOIOCTLCMD; struct net_device *dev; if (copy_from_user(&ifr, arg, sizeof(struct ifreq))) @@ -146,8 +146,10 @@ static int ieee802154_dev_ioctl(struct sock *sk, struct ifreq __user *arg, dev_load(sock_net(sk), ifr.ifr_name); dev = dev_get_by_name(sock_net(sk), ifr.ifr_name); - if (dev->type == ARPHRD_IEEE802154 || - dev->type == ARPHRD_IEEE802154_PHY) + + if ((dev->type == ARPHRD_IEEE802154 || + dev->type == ARPHRD_IEEE802154_PHY) && + dev->netdev_ops->ndo_do_ioctl) ret = dev->netdev_ops->ndo_do_ioctl(dev, &ifr, cmd); if (!ret && copy_to_user(arg, &ifr, sizeof(struct ifreq))) -- GitLab From a9dfac3353b03432e3d46a0dde6795588c46256d Mon Sep 17 00:00:00 2001 From: Dmitry Eremin-Solenikov Date: Mon, 3 Aug 2009 17:53:00 +0400 Subject: [PATCH 0859/1342] af_ieee802154: provide dummy get/setsockopt Provide dummt get/setsockopt implementations to stop these syscalls from oopsing on our sockets. Signed-off-by: Dmitry Eremin-Solenikov --- net/ieee802154/dgram.c | 14 ++++++++++++++ net/ieee802154/raw.c | 14 ++++++++++++++ 2 files changed, 28 insertions(+) diff --git a/net/ieee802154/dgram.c b/net/ieee802154/dgram.c index 14d39840dd6..ba8b214dda8 100644 --- a/net/ieee802154/dgram.c +++ b/net/ieee802154/dgram.c @@ -377,6 +377,18 @@ int ieee802154_dgram_deliver(struct net_device *dev, struct sk_buff *skb) return ret; } +static int dgram_getsockopt(struct sock *sk, int level, int optname, + char __user *optval, int __user *optlen) +{ + return -EOPNOTSUPP; +} + +static int dgram_setsockopt(struct sock *sk, int level, int optname, + char __user *optval, int __user optlen) +{ + return -EOPNOTSUPP; +} + struct proto ieee802154_dgram_prot = { .name = "IEEE-802.15.4-MAC", .owner = THIS_MODULE, @@ -391,5 +403,7 @@ struct proto ieee802154_dgram_prot = { .connect = dgram_connect, .disconnect = dgram_disconnect, .ioctl = dgram_ioctl, + .getsockopt = dgram_getsockopt, + .setsockopt = dgram_setsockopt, }; diff --git a/net/ieee802154/raw.c b/net/ieee802154/raw.c index fca44d59f97..9315977c4c6 100644 --- a/net/ieee802154/raw.c +++ b/net/ieee802154/raw.c @@ -238,6 +238,18 @@ void ieee802154_raw_deliver(struct net_device *dev, struct sk_buff *skb) read_unlock(&raw_lock); } +static int raw_getsockopt(struct sock *sk, int level, int optname, + char __user *optval, int __user *optlen) +{ + return -EOPNOTSUPP; +} + +static int raw_setsockopt(struct sock *sk, int level, int optname, + char __user *optval, int __user optlen) +{ + return -EOPNOTSUPP; +} + struct proto ieee802154_raw_prot = { .name = "IEEE-802.15.4-RAW", .owner = THIS_MODULE, @@ -250,5 +262,7 @@ struct proto ieee802154_raw_prot = { .unhash = raw_unhash, .connect = raw_connect, .disconnect = raw_disconnect, + .getsockopt = raw_getsockopt, + .setsockopt = raw_setsockopt, }; -- GitLab From 53a27b39ff4d2492f84b1fdc2f0047175f0b0b93 Mon Sep 17 00:00:00 2001 From: Marcelo Tosatti Date: Wed, 5 Aug 2009 15:43:58 -0300 Subject: [PATCH 0860/1342] KVM: MMU: limit rmap chain length Otherwise the host can spend too long traversing an rmap chain, which happens under a spinlock. Cc: stable@kernel.org Signed-off-by: Marcelo Tosatti Signed-off-by: Avi Kivity --- arch/x86/kvm/mmu.c | 33 ++++++++++++++++++++++++++++----- 1 file changed, 28 insertions(+), 5 deletions(-) diff --git a/arch/x86/kvm/mmu.c b/arch/x86/kvm/mmu.c index 49a10d00830..0ef5bb2b404 100644 --- a/arch/x86/kvm/mmu.c +++ b/arch/x86/kvm/mmu.c @@ -489,16 +489,20 @@ static unsigned long *gfn_to_rmap(struct kvm *kvm, gfn_t gfn, int lpage) * * If rmapp bit zero is one, (then rmap & ~1) points to a struct kvm_rmap_desc * containing more mappings. + * + * Returns the number of rmap entries before the spte was added or zero if + * the spte was not added. + * */ -static void rmap_add(struct kvm_vcpu *vcpu, u64 *spte, gfn_t gfn, int lpage) +static int rmap_add(struct kvm_vcpu *vcpu, u64 *spte, gfn_t gfn, int lpage) { struct kvm_mmu_page *sp; struct kvm_rmap_desc *desc; unsigned long *rmapp; - int i; + int i, count = 0; if (!is_rmap_pte(*spte)) - return; + return count; gfn = unalias_gfn(vcpu->kvm, gfn); sp = page_header(__pa(spte)); sp->gfns[spte - sp->spt] = gfn; @@ -515,8 +519,10 @@ static void rmap_add(struct kvm_vcpu *vcpu, u64 *spte, gfn_t gfn, int lpage) } else { rmap_printk("rmap_add: %p %llx many->many\n", spte, *spte); desc = (struct kvm_rmap_desc *)(*rmapp & ~1ul); - while (desc->shadow_ptes[RMAP_EXT-1] && desc->more) + while (desc->shadow_ptes[RMAP_EXT-1] && desc->more) { desc = desc->more; + count += RMAP_EXT; + } if (desc->shadow_ptes[RMAP_EXT-1]) { desc->more = mmu_alloc_rmap_desc(vcpu); desc = desc->more; @@ -525,6 +531,7 @@ static void rmap_add(struct kvm_vcpu *vcpu, u64 *spte, gfn_t gfn, int lpage) ; desc->shadow_ptes[i] = spte; } + return count; } static void rmap_desc_remove_entry(unsigned long *rmapp, @@ -754,6 +761,19 @@ static int kvm_age_rmapp(struct kvm *kvm, unsigned long *rmapp) return young; } +#define RMAP_RECYCLE_THRESHOLD 1000 + +static void rmap_recycle(struct kvm_vcpu *vcpu, gfn_t gfn, int lpage) +{ + unsigned long *rmapp; + + gfn = unalias_gfn(vcpu->kvm, gfn); + rmapp = gfn_to_rmap(vcpu->kvm, gfn, lpage); + + kvm_unmap_rmapp(vcpu->kvm, rmapp); + kvm_flush_remote_tlbs(vcpu->kvm); +} + int kvm_age_hva(struct kvm *kvm, unsigned long hva) { return kvm_handle_hva(kvm, hva, kvm_age_rmapp); @@ -1741,6 +1761,7 @@ static void mmu_set_spte(struct kvm_vcpu *vcpu, u64 *shadow_pte, { int was_rmapped = 0; int was_writeble = is_writeble_pte(*shadow_pte); + int rmap_count; pgprintk("%s: spte %llx access %x write_fault %d" " user_fault %d gfn %lx\n", @@ -1782,9 +1803,11 @@ static void mmu_set_spte(struct kvm_vcpu *vcpu, u64 *shadow_pte, page_header_update_slot(vcpu->kvm, shadow_pte, gfn); if (!was_rmapped) { - rmap_add(vcpu, shadow_pte, gfn, largepage); + rmap_count = rmap_add(vcpu, shadow_pte, gfn, largepage); if (!is_rmap_pte(*shadow_pte)) kvm_release_pfn_clean(pfn); + if (rmap_count > RMAP_RECYCLE_THRESHOLD) + rmap_recycle(vcpu, gfn, largepage); } else { if (was_writeble) kvm_release_pfn_dirty(pfn); -- GitLab From c5b1525533c484238015c48c78f86d49a1bfb86b Mon Sep 17 00:00:00 2001 From: Sheng Yang Date: Thu, 6 Aug 2009 13:31:56 +0800 Subject: [PATCH 0861/1342] intel-iommu: Fix enabling snooping feature by mistake Two defects work together result in KVM device passthrough randomly can't work: 1. iommu_snooping is not initialized to zero when vm_iommu_init() called. So it is possible to get a random value. 2. One line added by commit 2c2e2c38("IOMMU Identity Mapping Support") change the code path, let it bypass domain_update_iommu_cap(), as well as missing the increment of domain iommu reference count. The latter is also likely to cause a leak of domains on repeated VMM assignment and deassignment. Signed-off-by: Sheng Yang Signed-off-by: David Woodhouse --- drivers/pci/intel-iommu.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/pci/intel-iommu.c b/drivers/pci/intel-iommu.c index af7ff9b5aed..2314ad7ee5f 100644 --- a/drivers/pci/intel-iommu.c +++ b/drivers/pci/intel-iommu.c @@ -1505,7 +1505,6 @@ static int domain_context_mapping_one(struct dmar_domain *domain, int segment, } set_bit(num, iommu->domain_ids); - set_bit(iommu->seq_id, &domain->iommu_bmp); iommu->domains[num] = domain; id = num; } @@ -3409,6 +3408,7 @@ static int md_domain_init(struct dmar_domain *domain, int guest_width) domain->iommu_count = 0; domain->iommu_coherency = 0; + domain->iommu_snooping = 0; domain->max_addr = 0; /* always allocate the top pgd */ -- GitLab From e0d82a0a4e9841b787e6431ccfbb515546c55dc2 Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Thu, 6 Aug 2009 21:16:44 +1000 Subject: [PATCH 0862/1342] perf_counter/powerpc: Check oprofile_cpu_type for NULL before using it If the current CPU doesn't support performance counters, cur_cpu_spec->oprofile_cpu_type can be NULL. The current perf_counter modules don't test for that case and would thus crash at boot time. Bug reported by David Woodhouse. Reported-by: David Woodhouse Signed-off-by: Benjamin Herrenschmidt Cc: Peter Zijlstra Signed-off-by: Paul Mackerras LKML-Reference: <19066.48028.446975.501454@cargo.ozlabs.ibm.com> Signed-off-by: Ingo Molnar --- arch/powerpc/kernel/mpc7450-pmu.c | 3 ++- arch/powerpc/kernel/power4-pmu.c | 3 ++- arch/powerpc/kernel/power5+-pmu.c | 5 +++-- arch/powerpc/kernel/power5-pmu.c | 3 ++- arch/powerpc/kernel/power6-pmu.c | 3 ++- arch/powerpc/kernel/power7-pmu.c | 3 ++- arch/powerpc/kernel/ppc970-pmu.c | 5 +++-- 7 files changed, 16 insertions(+), 9 deletions(-) diff --git a/arch/powerpc/kernel/mpc7450-pmu.c b/arch/powerpc/kernel/mpc7450-pmu.c index c244133c67a..cc466d039af 100644 --- a/arch/powerpc/kernel/mpc7450-pmu.c +++ b/arch/powerpc/kernel/mpc7450-pmu.c @@ -407,7 +407,8 @@ struct power_pmu mpc7450_pmu = { static int init_mpc7450_pmu(void) { - if (strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc/7450")) + if (!cur_cpu_spec->oprofile_cpu_type || + strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc/7450")) return -ENODEV; return register_power_pmu(&mpc7450_pmu); diff --git a/arch/powerpc/kernel/power4-pmu.c b/arch/powerpc/kernel/power4-pmu.c index db90b0c5c27..3c90a3d9173 100644 --- a/arch/powerpc/kernel/power4-pmu.c +++ b/arch/powerpc/kernel/power4-pmu.c @@ -606,7 +606,8 @@ static struct power_pmu power4_pmu = { static int init_power4_pmu(void) { - if (strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power4")) + if (!cur_cpu_spec->oprofile_cpu_type || + strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power4")) return -ENODEV; return register_power_pmu(&power4_pmu); diff --git a/arch/powerpc/kernel/power5+-pmu.c b/arch/powerpc/kernel/power5+-pmu.c index f4adca8e98a..31918af3e35 100644 --- a/arch/powerpc/kernel/power5+-pmu.c +++ b/arch/powerpc/kernel/power5+-pmu.c @@ -678,8 +678,9 @@ static struct power_pmu power5p_pmu = { static int init_power5p_pmu(void) { - if (strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power5+") - && strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power5++")) + if (!cur_cpu_spec->oprofile_cpu_type || + (strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power5+") + && strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power5++"))) return -ENODEV; return register_power_pmu(&power5p_pmu); diff --git a/arch/powerpc/kernel/power5-pmu.c b/arch/powerpc/kernel/power5-pmu.c index 29b2c6c0e83..867f6f66396 100644 --- a/arch/powerpc/kernel/power5-pmu.c +++ b/arch/powerpc/kernel/power5-pmu.c @@ -618,7 +618,8 @@ static struct power_pmu power5_pmu = { static int init_power5_pmu(void) { - if (strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power5")) + if (!cur_cpu_spec->oprofile_cpu_type || + strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power5")) return -ENODEV; return register_power_pmu(&power5_pmu); diff --git a/arch/powerpc/kernel/power6-pmu.c b/arch/powerpc/kernel/power6-pmu.c index 09ae5bf5bda..fa21890531d 100644 --- a/arch/powerpc/kernel/power6-pmu.c +++ b/arch/powerpc/kernel/power6-pmu.c @@ -537,7 +537,8 @@ static struct power_pmu power6_pmu = { static int init_power6_pmu(void) { - if (strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power6")) + if (!cur_cpu_spec->oprofile_cpu_type || + strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power6")) return -ENODEV; return register_power_pmu(&power6_pmu); diff --git a/arch/powerpc/kernel/power7-pmu.c b/arch/powerpc/kernel/power7-pmu.c index 5a9f5cbd40a..388cf57ad82 100644 --- a/arch/powerpc/kernel/power7-pmu.c +++ b/arch/powerpc/kernel/power7-pmu.c @@ -366,7 +366,8 @@ static struct power_pmu power7_pmu = { static int init_power7_pmu(void) { - if (strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power7")) + if (!cur_cpu_spec->oprofile_cpu_type || + strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power7")) return -ENODEV; return register_power_pmu(&power7_pmu); diff --git a/arch/powerpc/kernel/ppc970-pmu.c b/arch/powerpc/kernel/ppc970-pmu.c index 833097ac45d..75dccb71a04 100644 --- a/arch/powerpc/kernel/ppc970-pmu.c +++ b/arch/powerpc/kernel/ppc970-pmu.c @@ -488,8 +488,9 @@ static struct power_pmu ppc970_pmu = { static int init_ppc970_pmu(void) { - if (strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/970") - && strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/970MP")) + if (!cur_cpu_spec->oprofile_cpu_type || + (strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/970") + && strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/970MP"))) return -ENODEV; return register_power_pmu(&ppc970_pmu); -- GitLab From 469535a598f28c13a2a42037e1b778f671af1d16 Mon Sep 17 00:00:00 2001 From: Robert Richter Date: Thu, 30 Jul 2009 19:19:18 +0200 Subject: [PATCH 0863/1342] ring-buffer: Fix advance of reader in rb_buffer_peek() When calling rb_buffer_peek() from ring_buffer_consume() and a padding event is returned, the function rb_advance_reader() is called twice. This may lead to missing samples or under high workloads to the warning below. This patch fixes this. If a padding event is returned by rb_buffer_peek() it will be consumed by the calling function now. Also, I simplified some code in ring_buffer_consume(). ------------[ cut here ]------------ WARNING: at /dev/shm/.source/linux/kernel/trace/ring_buffer.c:2289 rb_advance_reader+0x2e/0xc5() Hardware name: Anaheim Modules linked in: Pid: 29, comm: events/2 Tainted: G W 2.6.31-rc3-oprofile-x86_64-standard-00059-g5050dc2 #1 Call Trace: [] ? rb_advance_reader+0x2e/0xc5 [] warn_slowpath_common+0x77/0x8f [] warn_slowpath_null+0xf/0x11 [] rb_advance_reader+0x2e/0xc5 [] ring_buffer_consume+0xa0/0xd2 [] op_cpu_buffer_read_entry+0x21/0x9e [] ? __find_get_block+0x4b/0x165 [] sync_buffer+0xa5/0x401 [] ? __find_get_block+0x4b/0x165 [] ? wq_sync_buffer+0x0/0x78 [] wq_sync_buffer+0x5b/0x78 [] worker_thread+0x113/0x1ac [] ? autoremove_wake_function+0x0/0x38 [] ? worker_thread+0x0/0x1ac [] kthread+0x88/0x92 [] child_rip+0xa/0x20 [] ? kthread+0x0/0x92 [] ? child_rip+0x0/0x20 ---[ end trace f561c0a58fcc89bd ]--- Cc: Steven Rostedt Cc: Signed-off-by: Robert Richter Signed-off-by: Ingo Molnar --- kernel/trace/ring_buffer.c | 10 ++++------ 1 file changed, 4 insertions(+), 6 deletions(-) diff --git a/kernel/trace/ring_buffer.c b/kernel/trace/ring_buffer.c index 2606cee433d..d4d3580a894 100644 --- a/kernel/trace/ring_buffer.c +++ b/kernel/trace/ring_buffer.c @@ -2383,7 +2383,6 @@ rb_buffer_peek(struct ring_buffer *buffer, int cpu, u64 *ts) * the box. Return the padding, and we will release * the current locks, and try again. */ - rb_advance_reader(cpu_buffer); return event; case RINGBUF_TYPE_TIME_EXTEND: @@ -2519,6 +2518,8 @@ ring_buffer_peek(struct ring_buffer *buffer, int cpu, u64 *ts) if (dolock) spin_lock(&cpu_buffer->reader_lock); event = rb_buffer_peek(buffer, cpu, ts); + if (event && event->type_len == RINGBUF_TYPE_PADDING) + rb_advance_reader(cpu_buffer); if (dolock) spin_unlock(&cpu_buffer->reader_lock); local_irq_restore(flags); @@ -2590,12 +2591,9 @@ ring_buffer_consume(struct ring_buffer *buffer, int cpu, u64 *ts) spin_lock(&cpu_buffer->reader_lock); event = rb_buffer_peek(buffer, cpu, ts); - if (!event) - goto out_unlock; - - rb_advance_reader(cpu_buffer); + if (event) + rb_advance_reader(cpu_buffer); - out_unlock: if (dolock) spin_unlock(&cpu_buffer->reader_lock); local_irq_restore(flags); -- GitLab From 4d1e00a8af426500edfb8643fa6c375b89f1f804 Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Wed, 5 Aug 2009 19:02:49 -0300 Subject: [PATCH 0864/1342] perf symbol: Fix symbol parsing in certain cases: use the build-id as a symlink In some cases distros have binaries and debuginfo in weird places: [root@doppio tuna]# ls -la /usr/lib64/{xulrunner-1.9.1/xulrunner-stub,firefox-3.5.2/firefox} -rwxr-xr-x 1 root root 90024 2009-08-03 19:45 /usr/lib64/firefox-3.5.2/firefox -rwxr-xr-x 1 root root 90024 2009-08-03 18:23 /usr/lib64/xulrunner-1.9.1/xulrunner-stub [root@doppio tuna]# sha1sum /usr/lib64/{xulrunner-1.9.1/xulrunner-stub,firefox-3.5.2/firefox} 19a858077d263d5de22c9c5da250d3e4396ae739 /usr/lib64/xulrunner-1.9.1/xulrunner-stub 19a858077d263d5de22c9c5da250d3e4396ae739 /usr/lib64/firefox-3.5.2/firefox [root@doppio tuna]# rpm -qf /usr/lib64/{xulrunner-1.9.1/xulrunner-stub,firefox-3.5.2/firefox} xulrunner-1.9.1.2-1.fc11.x86_64 firefox-3.5.2-2.fc11.x86_64 [root@doppio tuna]# ls -la /usr/lib/debug/{usr/lib64/xulrunner-1.9.1/xulrunner-stub,usr/lib64/firefox-3.5.2/firefox}.debug ls: cannot access /usr/lib/debug/usr/lib64/firefox-3.5.2/firefox.debug: No such file or directory -rwxr-xr-x 1 root root 403608 2009-08-03 18:22 /usr/lib/debug/usr/lib64/xulrunner-1.9.1/xulrunner-stub.debug Seemingly we don't have a .symtab when we actually can find it if we use the .note.gnu.build-id ELF section put in place by some distros. Use it and find the symbols we need. Signed-off-by: Arnaldo Carvalho de Melo Acked-by: Peter Zijlstra LKML-Reference: Signed-off-by: Ingo Molnar --- tools/perf/util/symbol.c | 76 ++++++++++++++++++++++++++++++++++++++-- 1 file changed, 73 insertions(+), 3 deletions(-) diff --git a/tools/perf/util/symbol.c b/tools/perf/util/symbol.c index 0580b94785e..16ddca20294 100644 --- a/tools/perf/util/symbol.c +++ b/tools/perf/util/symbol.c @@ -661,10 +661,69 @@ out_close: return err; } +#define BUILD_ID_SIZE 128 + +static char *dso__read_build_id(struct dso *self, int verbose) +{ + int i; + GElf_Ehdr ehdr; + GElf_Shdr shdr; + Elf_Data *build_id_data; + Elf_Scn *sec; + char *build_id = NULL, *bid; + unsigned char *raw; + Elf *elf; + int fd = open(self->name, O_RDONLY); + + if (fd < 0) + goto out; + + elf = elf_begin(fd, ELF_C_READ_MMAP, NULL); + if (elf == NULL) { + if (verbose) + fprintf(stderr, "%s: cannot read %s ELF file.\n", + __func__, self->name); + goto out_close; + } + + if (gelf_getehdr(elf, &ehdr) == NULL) { + if (verbose) + fprintf(stderr, "%s: cannot get elf header.\n", __func__); + goto out_elf_end; + } + + sec = elf_section_by_name(elf, &ehdr, &shdr, ".note.gnu.build-id", NULL); + if (sec == NULL) + goto out_elf_end; + + build_id_data = elf_getdata(sec, NULL); + if (build_id_data == NULL) + goto out_elf_end; + build_id = malloc(BUILD_ID_SIZE); + if (build_id == NULL) + goto out_elf_end; + raw = build_id_data->d_buf + 16; + bid = build_id; + + for (i = 0; i < 20; ++i) { + sprintf(bid, "%02x", *raw); + ++raw; + bid += 2; + } + if (verbose) + printf("%s(%s): %s\n", __func__, self->name, build_id); +out_elf_end: + elf_end(elf); +out_close: + close(fd); +out: + return build_id; +} + int dso__load(struct dso *self, symbol_filter_t filter, int verbose) { - int size = strlen(self->name) + sizeof("/usr/lib/debug%s.debug"); - char *name = malloc(size); + int size = PATH_MAX; + char *name = malloc(size), *build_id = NULL; int variant = 0; int ret = -1; int fd; @@ -686,7 +745,18 @@ more: case 1: /* Ubuntu */ snprintf(name, size, "/usr/lib/debug%s", self->name); break; - case 2: /* Sane people */ + case 2: + build_id = dso__read_build_id(self, verbose); + if (build_id != NULL) { + snprintf(name, size, + "/usr/lib/debug/.build-id/%.2s/%s.debug", + build_id, build_id + 2); + free(build_id); + break; + } + variant++; + /* Fall thru */ + case 3: /* Sane people */ snprintf(name, size, "%s", self->name); break; -- GitLab From 9424edc2da097c8589fcc24a72552d33e54be161 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Wed, 5 Aug 2009 14:05:16 +0200 Subject: [PATCH 0865/1342] perf: Auto-detect libelf Adds autodetection for libelf as well, and simplifies the libbfd code. Furthermore, fail make with an error when libelf is not found and warn about the lack of libbfd. Also provide an option to build a 32bit version even though you might be running a 64bit kernel. Signed-off-by: Peter Zijlstra Signed-off-by: Ingo Molnar --- tools/perf/Makefile | 15 +++++++++++---- 1 file changed, 11 insertions(+), 4 deletions(-) diff --git a/tools/perf/Makefile b/tools/perf/Makefile index ff905aceb4f..1916e44b9bb 100644 --- a/tools/perf/Makefile +++ b/tools/perf/Makefile @@ -158,8 +158,10 @@ uname_P := $(shell sh -c 'uname -p 2>/dev/null || echo not') uname_V := $(shell sh -c 'uname -v 2>/dev/null || echo not') # If we're on a 64-bit kernel, use -m64 -ifneq ($(patsubst %64,%,$(uname_M)),$(uname_M)) - M64 := -m64 +ifndef NO_64BIT + ifneq ($(patsubst %64,%,$(uname_M)),$(uname_M)) + M64 := -m64 + endif endif # CFLAGS and LDFLAGS are for the users to override from the command line. @@ -373,19 +375,24 @@ ifeq ($(uname_S),Darwin) PTHREAD_LIBS = endif +ifneq ($(shell sh -c "(echo '\#include '; echo 'int main(void) { Elf * elf = elf_begin(0, ELF_C_READ_MMAP, 0); return (long)elf; }') | $(CC) -x c - $(ALL_CFLAGS) -D_LARGEFILE64_SOURCE -D_FILE_OFFSET_BITS=64 -o /dev/null $(ALL_LDFLAGS) > /dev/null 2>&1 && echo y"), y) + msg := $(error No libelf.h/libelf found, please install libelf-dev/elfutils-libelf-devel); +endif + ifdef NO_DEMANGLE BASIC_CFLAGS += -DNO_DEMANGLE else - has_bfd := $(shell sh -c "(echo '\#include '; echo '\#include '; echo '\#ifndef DMGL_PARAMS'; echo '\#define DMGL_PARAMS (1 << 0)'; echo '\#define DMGL_ANSI (1 << 1)'; echo '\#endif'; echo 'int main(int argc, char **argv) { bfd_demangle(NULL, argv[0], DMGL_PARAMS | DMGL_ANSI); return 0; }') | gcc -x c - -lbfd > /dev/null 2>&1 && echo y") + has_bfd := $(shell sh -c "(echo '\#include '; echo 'int main(void) { bfd_demangle(0, 0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -lbfd > /dev/null 2>&1 && echo y") - has_bfd_iberty := $(shell sh -c "(echo '\#include '; echo '\#include '; echo '\#ifndef DMGL_PARAMS'; echo '\#define DMGL_PARAMS (1 << 0)'; echo '\#define DMGL_ANSI (1 << 1)'; echo '\#endif'; echo 'int main(int argc, char **argv) { bfd_demangle(NULL, argv[0], DMGL_PARAMS | DMGL_ANSI); return 0; }') | gcc -x c - -lbfd -liberty > /dev/null 2>&1 && echo y") + has_bfd_iberty := $(shell sh -c "(echo '\#include '; echo 'int main(void) { bfd_demangle(0, 0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -lbfd -liberty > /dev/null 2>&1 && echo y") ifeq ($(has_bfd),y) EXTLIBS += -lbfd else ifeq ($(has_bfd_iberty),y) EXTLIBS += -lbfd -liberty else + msg := $(warning No bfd.h/libbfd found, install binutils-dev[el] to gain symbol demangling) BASIC_CFLAGS += -DNO_DEMANGLE endif endif -- GitLab From 1054598cab8674438675085fae459e960eb10799 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Thu, 6 Aug 2009 18:06:26 +0200 Subject: [PATCH 0866/1342] perf_counter: Fix double list iteration in per task precise stats Brice Goglin reported this crash with per task precise stats: > I finally managed to test the threaded perfcounter statistics (thanks a > lot for implementing it). I am running 2.6.31-rc5 (with the AMD > magny-cours patches but I don't think they matter here). I am trying to > measure local/remote memory accesses per thread during the well-known > stream benchmark. It's compiled with OpenMP using 16 threads on a > quad-socket quad-core barcelona machine. > > Command line is: > /mnt/scratch/bgoglin/cpunode/linux-2.6.31/tools/perf/perf record -f -s > -e r1000001e0 -e r1000002e0 -e r1000004e0 -e r1000008e0 ./stream > > It seems to work fine with a single -e on the command line > while it crashes when there are at least 2 of them. > It seems to work fine without -s as well. A silly copy-paste resulted in a messed up iteration which would cause the OOPS. Reported-by: Brice Goglin Signed-off-by: Peter Zijlstra Tested-by: Brice Goglin LKML-Reference: <1249574786.32113.550.camel@twins> Signed-off-by: Ingo Molnar --- kernel/perf_counter.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index 199ed477131..673c1aaf733 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -1104,7 +1104,7 @@ static void perf_counter_sync_stat(struct perf_counter_context *ctx, __perf_counter_sync_stat(counter, next_counter); counter = list_next_entry(counter, event_entry); - next_counter = list_next_entry(counter, event_entry); + next_counter = list_next_entry(next_counter, event_entry); } } -- GitLab From 17ac2e9c58b69a1e25460a568eae1b0dc0188c25 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Thu, 6 Aug 2009 03:34:06 +0000 Subject: [PATCH 0867/1342] rose: Fix rose_getname() leak rose_getname() can leak kernel memory to user. Signed-off-by: Eric Dumazet Signed-off-by: David S. Miller --- net/rose/af_rose.c | 1 + 1 file changed, 1 insertion(+) diff --git a/net/rose/af_rose.c b/net/rose/af_rose.c index f0a76f6bca7..e5f478ca3d6 100644 --- a/net/rose/af_rose.c +++ b/net/rose/af_rose.c @@ -954,6 +954,7 @@ static int rose_getname(struct socket *sock, struct sockaddr *uaddr, struct rose_sock *rose = rose_sk(sk); int n; + memset(srose, 0, sizeof(*srose)); if (peer != 0) { if (sk->sk_state != TCP_ESTABLISHED) return -ENOTCONN; -- GitLab From 80922bbb12a105f858a8f0abb879cb4302d0ecaa Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Thu, 6 Aug 2009 03:48:36 +0000 Subject: [PATCH 0868/1342] econet: Fix econet_getname() leak econet_getname() can leak kernel memory to user. Signed-off-by: Eric Dumazet Signed-off-by: David S. Miller --- net/econet/af_econet.c | 1 + 1 file changed, 1 insertion(+) diff --git a/net/econet/af_econet.c b/net/econet/af_econet.c index 2e1f836d424..f0bbc57926c 100644 --- a/net/econet/af_econet.c +++ b/net/econet/af_econet.c @@ -520,6 +520,7 @@ static int econet_getname(struct socket *sock, struct sockaddr *uaddr, if (peer) return -EOPNOTSUPP; + memset(sec, 0, sizeof(*sec)); mutex_lock(&econet_mutex); sk = sock->sk; -- GitLab From f6b97b29513950bfbf621a83d85b6f86b39ec8db Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Thu, 6 Aug 2009 03:31:07 +0000 Subject: [PATCH 0869/1342] netrom: Fix nr_getname() leak nr_getname() can leak kernel memory to user. Signed-off-by: Eric Dumazet Signed-off-by: David S. Miller --- net/netrom/af_netrom.c | 1 + 1 file changed, 1 insertion(+) diff --git a/net/netrom/af_netrom.c b/net/netrom/af_netrom.c index ce51ce012cd..ce1a34b99c2 100644 --- a/net/netrom/af_netrom.c +++ b/net/netrom/af_netrom.c @@ -847,6 +847,7 @@ static int nr_getname(struct socket *sock, struct sockaddr *uaddr, sax->fsa_ax25.sax25_family = AF_NETROM; sax->fsa_ax25.sax25_ndigis = 1; sax->fsa_ax25.sax25_call = nr->user_addr; + memset(sax->fsa_digipeater, 0, sizeof(sax->fsa_digipeater)); sax->fsa_digipeater[0] = nr->dest_addr; *uaddr_len = sizeof(struct full_sockaddr_ax25); } else { -- GitLab From 3d392475c873c10c10d6d96b94d092a34ebd4791 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Thu, 6 Aug 2009 02:27:43 +0000 Subject: [PATCH 0870/1342] appletalk: fix atalk_getname() leak atalk_getname() can leak 8 bytes of kernel memory to user Signed-off-by: Eric Dumazet Signed-off-by: David S. Miller --- net/appletalk/ddp.c | 1 + 1 file changed, 1 insertion(+) diff --git a/net/appletalk/ddp.c b/net/appletalk/ddp.c index 590b8396362..9ef6ff26eb0 100644 --- a/net/appletalk/ddp.c +++ b/net/appletalk/ddp.c @@ -1237,6 +1237,7 @@ static int atalk_getname(struct socket *sock, struct sockaddr *uaddr, return -ENOBUFS; *uaddr_len = sizeof(struct sockaddr_at); + memset(&sat.sat_zero, 0, sizeof(sat.sat_zero)); if (peer) { if (sk->sk_state != TCP_ESTABLISHED) -- GitLab From 09384dfc76e526c3993c09c42e016372dc9dd22c Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Thu, 6 Aug 2009 03:55:04 +0000 Subject: [PATCH 0871/1342] irda: Fix irda_getname() leak irda_getname() can leak kernel memory to user. Signed-off-by: Eric Dumazet Signed-off-by: David S. Miller --- net/irda/af_irda.c | 1 + 1 file changed, 1 insertion(+) diff --git a/net/irda/af_irda.c b/net/irda/af_irda.c index cb762c8723e..3ec2b434ea7 100644 --- a/net/irda/af_irda.c +++ b/net/irda/af_irda.c @@ -714,6 +714,7 @@ static int irda_getname(struct socket *sock, struct sockaddr *uaddr, struct sock *sk = sock->sk; struct irda_sock *self = irda_sk(sk); + memset(&saddr, 0, sizeof(saddr)); if (peer) { if (sk->sk_state != TCP_ESTABLISHED) return -ENOTCONN; -- GitLab From 7dbdee2e9a2ac42ea5135801bcc9d1a8e3f672aa Mon Sep 17 00:00:00 2001 From: Steven Rostedt Date: Thu, 6 Aug 2009 19:53:18 -0400 Subject: [PATCH 0872/1342] tracing: Fix recordmcount.pl to handle sections with only weak functions Roland Dreier found that a section that contained only a weak function in one of the staging drivers and this caused recordmcount.pl to spit out a warning and fail. Although it is strange that a driver would have a weak function, and this function only be used in one place, it should not be something to make recordmcount.pl fail. This patch fixes the issue in a simple manner: if only weak functions exist in a section, then that section will not be recorded. Reported-by: Roland Dreier Signed-off-by: Steven Rostedt Signed-off-by: Ingo Molnar --- scripts/recordmcount.pl | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/scripts/recordmcount.pl b/scripts/recordmcount.pl index 4889c44d71b..911ba7ffab8 100755 --- a/scripts/recordmcount.pl +++ b/scripts/recordmcount.pl @@ -393,7 +393,7 @@ while () { $read_function = 0; } # print out any recorded offsets - update_funcs() if ($text_found); + update_funcs() if (defined($ref_func)); # reset all markers and arrays $text_found = 0; @@ -444,7 +444,7 @@ while () { } # dump out anymore offsets that may have been found -update_funcs() if ($text_found); +update_funcs() if (defined($ref_func)); # If we did not find any mcount callers, we are done (do nothing). if (!$opened) { -- GitLab From 677c1dd706d9cc384730cbd52baf821923d8be9b Mon Sep 17 00:00:00 2001 From: Hendrik Brueckner Date: Fri, 7 Aug 2009 10:39:24 +0200 Subject: [PATCH 0873/1342] [S390] kernel: Storing machine flags early in lowcore Currently, the machine_flags are stored late in the startup initialization which results in failing machine type checks (e.g. for MACHINE_IS_VM). To allow these checks, store the machine flags in the lowcore when the machine type has been detected. Moving the machine_flags to the lowcore has been introduced with git commit 25097bf153391f7be4c591d47061b3dc4990dac2 Signed-off-by: Hendrik Brueckner Signed-off-by: Martin Schwidefsky --- arch/s390/kernel/early.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/s390/kernel/early.c b/arch/s390/kernel/early.c index 8d15314381e..cae14c49951 100644 --- a/arch/s390/kernel/early.c +++ b/arch/s390/kernel/early.c @@ -208,6 +208,9 @@ static noinline __init void detect_machine_type(void) machine_flags |= MACHINE_FLAG_KVM; else machine_flags |= MACHINE_FLAG_VM; + + /* Store machine flags for setting up lowcore early */ + S390_lowcore.machine_flags = machine_flags; } static __init void early_pgm_check_handler(void) -- GitLab From 53cb780adbe69df90c8dc23e992ce40455e687c3 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Fri, 7 Aug 2009 10:39:25 +0200 Subject: [PATCH 0874/1342] [S390] KVM: Read buffer overflow Check whether index is within bounds before testing the element. Signed-off-by: Roel Kluin Signed-off-by: Martin Schwidefsky --- arch/s390/kvm/sigp.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/arch/s390/kvm/sigp.c b/arch/s390/kvm/sigp.c index 36678835034..0ef81d6776e 100644 --- a/arch/s390/kvm/sigp.c +++ b/arch/s390/kvm/sigp.c @@ -169,7 +169,7 @@ static int __sigp_set_prefix(struct kvm_vcpu *vcpu, u16 cpu_addr, u32 address, unsigned long *reg) { struct kvm_s390_float_interrupt *fi = &vcpu->kvm->arch.float_int; - struct kvm_s390_local_interrupt *li; + struct kvm_s390_local_interrupt *li = NULL; struct kvm_s390_interrupt_info *inti; int rc; u8 tmp; @@ -189,9 +189,10 @@ static int __sigp_set_prefix(struct kvm_vcpu *vcpu, u16 cpu_addr, u32 address, return 2; /* busy */ spin_lock(&fi->lock); - li = fi->local_int[cpu_addr]; + if (cpu_addr < KVM_MAX_VCPUS) + li = fi->local_int[cpu_addr]; - if ((cpu_addr >= KVM_MAX_VCPUS) || (li == NULL)) { + if (li == NULL) { rc = 1; /* incorrect state */ *reg &= SIGP_STAT_INCORRECT_STATE; kfree(inti); -- GitLab From 9795447f71324d8f14c19ed68b43c883135c3f59 Mon Sep 17 00:00:00 2001 From: Li Zefan Date: Fri, 7 Aug 2009 16:37:10 +0800 Subject: [PATCH 0875/1342] lockdep: Fix file mode of lock_stat /proc/lock_stat is writable. Signed-off-by: Li Zefan Cc: Peter Zijlstra LKML-Reference: <4A7BE7B6.10904@cn.fujitsu.com> Signed-off-by: Ingo Molnar --- kernel/lockdep_proc.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/kernel/lockdep_proc.c b/kernel/lockdep_proc.c index d7135aa2d2c..e94caa666db 100644 --- a/kernel/lockdep_proc.c +++ b/kernel/lockdep_proc.c @@ -758,7 +758,8 @@ static int __init lockdep_proc_init(void) &proc_lockdep_stats_operations); #ifdef CONFIG_LOCK_STAT - proc_create("lock_stat", S_IRUSR, NULL, &proc_lock_stat_operations); + proc_create("lock_stat", S_IRUSR | S_IWUSR, NULL, + &proc_lock_stat_operations); #endif return 0; -- GitLab From 0e692a94e378628b7d527260ad939894454bcca8 Mon Sep 17 00:00:00 2001 From: Li Zefan Date: Fri, 7 Aug 2009 15:10:54 +0800 Subject: [PATCH 0876/1342] lockdep: Fix typos in documentation s/head/held Signed-off-by: Li Zefan Cc: Peter Zijlstra LKML-Reference: <4A7BD37E.9060806@cn.fujitsu.com> Signed-off-by: Ingo Molnar --- Documentation/lockdep-design.txt | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/Documentation/lockdep-design.txt b/Documentation/lockdep-design.txt index e20d913d591..abf768c681e 100644 --- a/Documentation/lockdep-design.txt +++ b/Documentation/lockdep-design.txt @@ -30,9 +30,9 @@ State The validator tracks lock-class usage history into 4n + 1 separate state bits: - 'ever held in STATE context' -- 'ever head as readlock in STATE context' -- 'ever head with STATE enabled' -- 'ever head as readlock with STATE enabled' +- 'ever held as readlock in STATE context' +- 'ever held with STATE enabled' +- 'ever held as readlock with STATE enabled' Where STATE can be either one of (kernel/lockdep_states.h) - hardirq -- GitLab From 17332925d7b11bb6c2d0c49450ae58dd836005da Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Fri, 7 Aug 2009 11:03:26 +1000 Subject: [PATCH 0877/1342] drm/radeon/kms: setup MC/VRAM the same way for suspend/resume we should align the GTT after VRAM no matter what, as we can come back from resume and put in a different place and bad things happen. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_device.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c index a162ade74b7..9ff6dcb97f9 100644 --- a/drivers/gpu/drm/radeon/radeon_device.c +++ b/drivers/gpu/drm/radeon/radeon_device.c @@ -152,7 +152,9 @@ int radeon_mc_setup(struct radeon_device *rdev) } } else { rdev->mc.vram_location = 0; - rdev->mc.gtt_location = rdev->mc.mc_vram_size; + tmp = rdev->mc.mc_vram_size; + tmp = (tmp + rdev->mc.gtt_size - 1) & ~(rdev->mc.gtt_size - 1); + rdev->mc.gtt_location = tmp; } DRM_INFO("radeon: VRAM %uM\n", rdev->mc.real_vram_size >> 20); DRM_INFO("radeon: VRAM from 0x%08X to 0x%08X\n", -- GitLab From afc5e65245255a268ab22a20477ed2c9f2cdfcd3 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Fri, 7 Aug 2009 16:33:53 +0200 Subject: [PATCH 0878/1342] ASoC: Add missing DRV_NAME definitions for fsl/* drivers Module builds are broken due to missing DRV_NAME for efika-audio-fabric and pcm030-audio-fabric. Signed-off-by: Takashi Iwai --- sound/soc/fsl/efika-audio-fabric.c | 2 ++ sound/soc/fsl/pcm030-audio-fabric.c | 2 ++ 2 files changed, 4 insertions(+) diff --git a/sound/soc/fsl/efika-audio-fabric.c b/sound/soc/fsl/efika-audio-fabric.c index 85b0e756950..3326e2a1e86 100644 --- a/sound/soc/fsl/efika-audio-fabric.c +++ b/sound/soc/fsl/efika-audio-fabric.c @@ -30,6 +30,8 @@ #include "mpc5200_psc_ac97.h" #include "../codecs/stac9766.h" +#define DRV_NAME "efika-audio-fabric" + static struct snd_soc_device device; static struct snd_soc_card card; diff --git a/sound/soc/fsl/pcm030-audio-fabric.c b/sound/soc/fsl/pcm030-audio-fabric.c index 8766f7a3893..b928ef7d28e 100644 --- a/sound/soc/fsl/pcm030-audio-fabric.c +++ b/sound/soc/fsl/pcm030-audio-fabric.c @@ -30,6 +30,8 @@ #include "mpc5200_psc_ac97.h" #include "../codecs/wm9712.h" +#define DRV_NAME "pcm030-audio-fabric" + static struct snd_soc_device device; static struct snd_soc_card card; -- GitLab From bd3f02212d6a457267e0c9c02c426151c436d9d4 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Fri, 7 Aug 2009 12:49:29 +0200 Subject: [PATCH 0879/1342] ring-buffer: Fix memleak in ring_buffer_free() I noticed oprofile memleaked in linux-2.6 current tree, and tracked this ring-buffer leak. Signed-off-by: Eric Dumazet LKML-Reference: <4A7C06B9.2090302@gmail.com> Cc: stable@kernel.org Signed-off-by: Steven Rostedt --- kernel/trace/ring_buffer.c | 1 + 1 file changed, 1 insertion(+) diff --git a/kernel/trace/ring_buffer.c b/kernel/trace/ring_buffer.c index d4d3580a894..a330513d96c 100644 --- a/kernel/trace/ring_buffer.c +++ b/kernel/trace/ring_buffer.c @@ -735,6 +735,7 @@ ring_buffer_free(struct ring_buffer *buffer) put_online_cpus(); + kfree(buffer->buffers); free_cpumask_var(buffer->cpumask); kfree(buffer); -- GitLab From 7dd2459d8f7a967bcd1466591aec72bb3ddc07cc Mon Sep 17 00:00:00 2001 From: Zhu Yi Date: Mon, 27 Jul 2009 10:10:20 +0800 Subject: [PATCH 0880/1342] ipw2x00: Write outside array bounds > channel_index loops up to IPW_SCAN_CHANNELS, but is used after being > incremented. This might be able to access 1 past the end of the array Reported-by: Roel Kluin Signed-off-by: John W. Linville --- drivers/net/wireless/ipw2x00/ipw2200.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/wireless/ipw2x00/ipw2200.c b/drivers/net/wireless/ipw2x00/ipw2200.c index 44c29b3f672..6dcac73b4d2 100644 --- a/drivers/net/wireless/ipw2x00/ipw2200.c +++ b/drivers/net/wireless/ipw2x00/ipw2200.c @@ -6226,7 +6226,7 @@ static void ipw_add_scan_channels(struct ipw_priv *priv, }; u8 channel; - while (channel_index < IPW_SCAN_CHANNELS) { + while (channel_index < IPW_SCAN_CHANNELS - 1) { channel = priv->speed_scan[priv->speed_scan_pos]; if (channel == 0) { -- GitLab From d25f9f1357139bbdc79bc960ea84909a7c22ec2b Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Mon, 3 Aug 2009 21:58:26 +0200 Subject: [PATCH 0881/1342] mwl8k: fix NULL pointer dereference on receive out-of-memory When we go into out-of-memory and fail to allocate skbuffs to refill the receive ring with, rxq_process can end up running into a receive ring entry that is marked as host-owned but doesn't have an associated skbuff. If this happens, we must break out of the rx processing loop instead of trying to process the descriptor. Signed-off-by: Lennert Buytenhek Acked-by: Nicolas Pitre Signed-off-by: John W. Linville --- drivers/net/wireless/mwl8k.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/net/wireless/mwl8k.c b/drivers/net/wireless/mwl8k.c index a263d5c84c0..71f3eb67981 100644 --- a/drivers/net/wireless/mwl8k.c +++ b/drivers/net/wireless/mwl8k.c @@ -1012,6 +1012,8 @@ static int rxq_process(struct ieee80211_hw *hw, int index, int limit) rmb(); skb = rxq->rx_skb[rxq->rx_head]; + if (skb == NULL) + break; rxq->rx_skb[rxq->rx_head] = NULL; rxq->rx_head = (rxq->rx_head + 1) % MWL8K_RX_DESCS; -- GitLab From 4ff6432ea620ba467e50ec04b8271ea0eb94e62e Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Mon, 3 Aug 2009 21:58:39 +0200 Subject: [PATCH 0882/1342] mwl8k: add various missing GET_HW_SPEC endian conversions Signed-off-by: Lennert Buytenhek Acked-by: Nicolas Pitre Signed-off-by: John W. Linville --- drivers/net/wireless/mwl8k.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/net/wireless/mwl8k.c b/drivers/net/wireless/mwl8k.c index 71f3eb67981..9643aa4751c 100644 --- a/drivers/net/wireless/mwl8k.c +++ b/drivers/net/wireless/mwl8k.c @@ -1656,18 +1656,18 @@ static int mwl8k_cmd_get_hw_spec(struct ieee80211_hw *hw) memset(cmd->perm_addr, 0xff, sizeof(cmd->perm_addr)); cmd->ps_cookie = cpu_to_le32(priv->cookie_dma); cmd->rx_queue_ptr = cpu_to_le32(priv->rxq[0].rx_desc_dma); - cmd->num_tx_queues = MWL8K_TX_QUEUES; + cmd->num_tx_queues = cpu_to_le32(MWL8K_TX_QUEUES); for (i = 0; i < MWL8K_TX_QUEUES; i++) cmd->tx_queue_ptrs[i] = cpu_to_le32(priv->txq[i].tx_desc_dma); - cmd->num_tx_desc_per_queue = MWL8K_TX_DESCS; - cmd->total_rx_desc = MWL8K_RX_DESCS; + cmd->num_tx_desc_per_queue = cpu_to_le32(MWL8K_TX_DESCS); + cmd->total_rx_desc = cpu_to_le32(MWL8K_RX_DESCS); rc = mwl8k_post_cmd(hw, &cmd->header); if (!rc) { SET_IEEE80211_PERM_ADDR(hw, cmd->perm_addr); priv->num_mcaddrs = le16_to_cpu(cmd->num_mcaddrs); - priv->fw_rev = cmd->fw_rev; + priv->fw_rev = le32_to_cpu(cmd->fw_rev); priv->hw_rev = cmd->hw_rev; priv->region_code = le16_to_cpu(cmd->region_code); } -- GitLab From 37055bd455b31b8220c35a1ede9c6aceb791cc88 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Mon, 3 Aug 2009 21:58:47 +0200 Subject: [PATCH 0883/1342] mwl8k: call pci_unmap_single() before accessing command structure again Signed-off-by: Lennert Buytenhek Acked-by: Nicolas Pitre Signed-off-by: John W. Linville --- drivers/net/wireless/mwl8k.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/net/wireless/mwl8k.c b/drivers/net/wireless/mwl8k.c index 9643aa4751c..25423c05aff 100644 --- a/drivers/net/wireless/mwl8k.c +++ b/drivers/net/wireless/mwl8k.c @@ -1593,6 +1593,9 @@ static int mwl8k_post_cmd(struct ieee80211_hw *hw, struct mwl8k_cmd_pkt *cmd) timeout = wait_for_completion_timeout(&cmd_wait, msecs_to_jiffies(MWL8K_CMD_TIMEOUT_MS)); + pci_unmap_single(priv->pdev, dma_addr, dma_size, + PCI_DMA_BIDIRECTIONAL); + result = &cmd->result; if (!timeout) { spin_lock_irq(&priv->fw_lock); @@ -1612,8 +1615,6 @@ static int mwl8k_post_cmd(struct ieee80211_hw *hw, struct mwl8k_cmd_pkt *cmd) *result); } - pci_unmap_single(priv->pdev, dma_addr, dma_size, - PCI_DMA_BIDIRECTIONAL); return rc; } -- GitLab From a94cc97e14c5750ec2b50b2e4ecdfb0f369ed0f4 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Mon, 3 Aug 2009 21:58:57 +0200 Subject: [PATCH 0884/1342] mwl8k: prevent crash in ->configure_filter() if no interface was added Signed-off-by: Lennert Buytenhek Acked-by: Nicolas Pitre Signed-off-by: John W. Linville --- drivers/net/wireless/mwl8k.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) diff --git a/drivers/net/wireless/mwl8k.c b/drivers/net/wireless/mwl8k.c index 25423c05aff..6e491171f73 100644 --- a/drivers/net/wireless/mwl8k.c +++ b/drivers/net/wireless/mwl8k.c @@ -261,7 +261,7 @@ struct mwl8k_vif { */ }; -#define MWL8K_VIF(_vif) (struct mwl8k_vif *)(&((_vif)->drv_priv)) +#define MWL8K_VIF(_vif) ((struct mwl8k_vif *)&((_vif)->drv_priv)) static const struct ieee80211_channel mwl8k_channels[] = { { .center_freq = 2412, .hw_value = 1, }, @@ -3219,15 +3219,19 @@ static int mwl8k_configure_filter_wt(struct work_struct *wt) struct dev_addr_list *mclist = worker->mclist; struct mwl8k_priv *priv = hw->priv; - struct mwl8k_vif *mv_vif; int rc = 0; if (changed_flags & FIF_BCN_PRBRESP_PROMISC) { if (*total_flags & FIF_BCN_PRBRESP_PROMISC) rc = mwl8k_cmd_set_pre_scan(hw); else { - mv_vif = MWL8K_VIF(priv->vif); - rc = mwl8k_cmd_set_post_scan(hw, mv_vif->bssid); + u8 *bssid; + + bssid = "\x00\x00\x00\x00\x00\x00"; + if (priv->vif != NULL) + bssid = MWL8K_VIF(priv->vif)->bssid; + + rc = mwl8k_cmd_set_post_scan(hw, bssid); } } -- GitLab From 60aa569f9212a13382c29cc734f275dec0f55e0b Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Mon, 3 Aug 2009 21:59:09 +0200 Subject: [PATCH 0885/1342] mwl8k: prevent module unload hang We need to unregister our ieee80211_hw before resetting the chip, as the former causes firmware commands to be issued which will time out once the chip has been reset. Signed-off-by: Lennert Buytenhek Acked-by: Nicolas Pitre Signed-off-by: John W. Linville --- drivers/net/wireless/mwl8k.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/wireless/mwl8k.c b/drivers/net/wireless/mwl8k.c index 6e491171f73..83967afe082 100644 --- a/drivers/net/wireless/mwl8k.c +++ b/drivers/net/wireless/mwl8k.c @@ -3733,6 +3733,8 @@ static void __devexit mwl8k_remove(struct pci_dev *pdev) ieee80211_stop_queues(hw); + ieee80211_unregister_hw(hw); + /* Remove tx reclaim tasklet */ tasklet_kill(&priv->tx_reclaim_task); @@ -3746,8 +3748,6 @@ static void __devexit mwl8k_remove(struct pci_dev *pdev) for (i = 0; i < MWL8K_TX_QUEUES; i++) mwl8k_txq_reclaim(hw, i, 1); - ieee80211_unregister_hw(hw); - for (i = 0; i < MWL8K_TX_QUEUES; i++) mwl8k_txq_deinit(hw, i); -- GitLab From dd1f57ecaf9688efa69d982652ecfa3e64f1fa55 Mon Sep 17 00:00:00 2001 From: Bob Dunlop Date: Thu, 6 Aug 2009 12:01:03 -0400 Subject: [PATCH 0886/1342] libertas: correct packing of rxpd structure Older Gcc compilers (3.4.5 tested) need additional hints in order to get the packing of the rxpd structure (which contains a 16 bit union) correct on the ARM processor. struct txpd does not need these hints since it contains a 32 bit union that packs naturally. Signed-off-by: R.J.Dunlop Acked-by: Dan Williams Signed-off-by: John W. Linville --- drivers/net/wireless/libertas/hostcmd.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/wireless/libertas/hostcmd.h b/drivers/net/wireless/libertas/hostcmd.h index 0a2e29140ad..c8a1998d474 100644 --- a/drivers/net/wireless/libertas/hostcmd.h +++ b/drivers/net/wireless/libertas/hostcmd.h @@ -56,8 +56,8 @@ struct rxpd { u8 bss_type; /* BSS number */ u8 bss_num; - } bss; - } u; + } __attribute__ ((packed)) bss; + } __attribute__ ((packed)) u; /* SNR */ u8 snr; -- GitLab From d25f14389a65c7f95512b01415d8d4a8d62855ab Mon Sep 17 00:00:00 2001 From: Kenji Kaneshige Date: Mon, 27 Jul 2009 12:05:38 +0900 Subject: [PATCH 0887/1342] PCI hotplug: SGI hotplug: fix build failure The commit bd3d99c17039fd05a29587db3f4a180c48da115a ("PCI: Remove untested Electromechanical Interlock (EMI) support in pciehp."), which removes the definition of "struct hotplug_slot_attr", broke SGI hotplug driver. By this commit, we get the following compile error. drivers/pci/hotplug/sgi_hotplug.c:106: error: variable 'sn_slot_path_attr' has initializer but incomplete type drivers/pci/hotplug/sgi_hotplug.c:106: error: unknown field 'attr' specified in initializer drivers/pci/hotplug/sgi_hotplug.c:106: error: extra brace group at end of initializer drivers/pci/hotplug/sgi_hotplug.c:106: error: (near initialization for 'sn_slot_path_attr') drivers/pci/hotplug/sgi_hotplug.c:106: warning: excess elements in struct initializer drivers/pci/hotplug/sgi_hotplug.c:106: warning: (near initialization for 'sn_slot_path_attr') drivers/pci/hotplug/sgi_hotplug.c:106: error: unknown field 'show' specified in initializer drivers/pci/hotplug/sgi_hotplug.c:106: warning: excess elements in struct initializer drivers/pci/hotplug/sgi_hotplug.c:106: warning: (near initialization for 'sn_slot_path_attr') drivers/pci/hotplug/sgi_hotplug.c: In function 'sn_hp_destroy': drivers/pci/hotplug/sgi_hotplug.c:203: error: invalid use of undefined type 'struct hotplug_slot_attribute' drivers/pci/hotplug/sgi_hotplug.c: In function 'sn_hotplug_slot_register': drivers/pci/hotplug/sgi_hotplug.c:655: error: invalid use of undefined type 'struct hotplug_slot_attribute' This patch fixes this regression by adding the definition of struct hotplug_slot_attr into sgi_hotplug.c. Tested-by: Mike Habeck Signed-off-by: Kenji Kaneshige Signed-off-by: Jesse Barnes --- drivers/pci/hotplug/sgi_hotplug.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/pci/hotplug/sgi_hotplug.c b/drivers/pci/hotplug/sgi_hotplug.c index a4494d78e7c..0a724bb6ba1 100644 --- a/drivers/pci/hotplug/sgi_hotplug.c +++ b/drivers/pci/hotplug/sgi_hotplug.c @@ -103,6 +103,12 @@ static ssize_t path_show (struct hotplug_slot *bss_hotplug_slot, return retval; } +struct hotplug_slot_attribute { + struct attribute attr; + ssize_t (*show)(struct hotplug_slot *, char *); + ssize_t (*store)(struct hotplug_slot *, const char *, size_t); +}; + static struct hotplug_slot_attribute sn_slot_path_attr = __ATTR_RO(path); static int sn_pci_slot_valid(struct pci_bus *pci_bus, int device) -- GitLab From 94f81a47c4a7a2d7a16fcfdd6d81da381732c101 Mon Sep 17 00:00:00 2001 From: Kenji Kaneshige Date: Mon, 27 Jul 2009 12:06:46 +0900 Subject: [PATCH 0888/1342] PCI hotplug: SGI hotplug: do not use hotplug_slot_attr By the pci slot changes, callbacks of attributes under slot directory (/sys/bus/pci/slots) had been changed to get the pointer to struct pci_slot instead of struct hotplug_slot. So the path_show() that assumes the parameter is a pointer to struct hotplug_slot seems broken. Tested-by: Mike Habeck Signed-off-by: Kenji Kaneshige Signed-off-by: Jesse Barnes --- drivers/pci/hotplug/sgi_hotplug.c | 13 +++---------- 1 file changed, 3 insertions(+), 10 deletions(-) diff --git a/drivers/pci/hotplug/sgi_hotplug.c b/drivers/pci/hotplug/sgi_hotplug.c index 0a724bb6ba1..8aebe1e9d3d 100644 --- a/drivers/pci/hotplug/sgi_hotplug.c +++ b/drivers/pci/hotplug/sgi_hotplug.c @@ -90,11 +90,10 @@ static struct hotplug_slot_ops sn_hotplug_slot_ops = { static DEFINE_MUTEX(sn_hotplug_mutex); -static ssize_t path_show (struct hotplug_slot *bss_hotplug_slot, - char *buf) +static ssize_t path_show(struct pci_slot *pci_slot, char *buf) { int retval = -ENOENT; - struct slot *slot = bss_hotplug_slot->private; + struct slot *slot = pci_slot->hotplug->private; if (!slot) return retval; @@ -103,13 +102,7 @@ static ssize_t path_show (struct hotplug_slot *bss_hotplug_slot, return retval; } -struct hotplug_slot_attribute { - struct attribute attr; - ssize_t (*show)(struct hotplug_slot *, char *); - ssize_t (*store)(struct hotplug_slot *, const char *, size_t); -}; - -static struct hotplug_slot_attribute sn_slot_path_attr = __ATTR_RO(path); +static struct pci_slot_attribute sn_slot_path_attr = __ATTR_RO(path); static int sn_pci_slot_valid(struct pci_bus *pci_bus, int device) { -- GitLab From 54e346215e4fe2ca8c94c54e546cc61902060510 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Fri, 7 Aug 2009 14:38:25 -0300 Subject: [PATCH 0889/1342] vfs: fix inode_init_always calling convention Currently inode_init_always calls into ->destroy_inode if the additional initialization fails. That's not only counter-intuitive because inode_init_always did not allocate the inode structure, but in case of XFS it's actively harmful as ->destroy_inode might delete the inode from a radix-tree that has never been added. This in turn might end up deleting the inode for the same inum that has been instanciated by another process and cause lots of cause subtile problems. Also in the case of re-initializing a reclaimable inode in XFS it would free an inode we still want to keep alive. Signed-off-by: Christoph Hellwig Reviewed-by: Eric Sandeen --- fs/inode.c | 30 +++++++++++++++++------------- fs/xfs/xfs_iget.c | 17 +++++------------ include/linux/fs.h | 2 +- 3 files changed, 23 insertions(+), 26 deletions(-) diff --git a/fs/inode.c b/fs/inode.c index 901bad1e5f1..af2c05235cc 100644 --- a/fs/inode.c +++ b/fs/inode.c @@ -120,12 +120,11 @@ static void wake_up_inode(struct inode *inode) * These are initializations that need to be done on every inode * allocation as the fields are not initialised by slab allocation. */ -struct inode *inode_init_always(struct super_block *sb, struct inode *inode) +int inode_init_always(struct super_block *sb, struct inode *inode) { static const struct address_space_operations empty_aops; static struct inode_operations empty_iops; static const struct file_operations empty_fops; - struct address_space *const mapping = &inode->i_data; inode->i_sb = sb; @@ -152,7 +151,7 @@ struct inode *inode_init_always(struct super_block *sb, struct inode *inode) inode->dirtied_when = 0; if (security_inode_alloc(inode)) - goto out_free_inode; + goto out; /* allocate and initialize an i_integrity */ if (ima_inode_alloc(inode)) @@ -198,16 +197,12 @@ struct inode *inode_init_always(struct super_block *sb, struct inode *inode) inode->i_fsnotify_mask = 0; #endif - return inode; + return 0; out_free_security: security_inode_free(inode); -out_free_inode: - if (inode->i_sb->s_op->destroy_inode) - inode->i_sb->s_op->destroy_inode(inode); - else - kmem_cache_free(inode_cachep, (inode)); - return NULL; +out: + return -ENOMEM; } EXPORT_SYMBOL(inode_init_always); @@ -220,9 +215,18 @@ static struct inode *alloc_inode(struct super_block *sb) else inode = kmem_cache_alloc(inode_cachep, GFP_KERNEL); - if (inode) - return inode_init_always(sb, inode); - return NULL; + if (!inode) + return NULL; + + if (unlikely(inode_init_always(sb, inode))) { + if (inode->i_sb->s_op->destroy_inode) + inode->i_sb->s_op->destroy_inode(inode); + else + kmem_cache_free(inode_cachep, inode); + return NULL; + } + + return inode; } void destroy_inode(struct inode *inode) diff --git a/fs/xfs/xfs_iget.c b/fs/xfs/xfs_iget.c index 5fcec6f020a..719c85b155f 100644 --- a/fs/xfs/xfs_iget.c +++ b/fs/xfs/xfs_iget.c @@ -64,6 +64,10 @@ xfs_inode_alloc( ip = kmem_zone_alloc(xfs_inode_zone, KM_SLEEP); if (!ip) return NULL; + if (inode_init_always(mp->m_super, VFS_I(ip))) { + kmem_zone_free(xfs_inode_zone, ip); + return NULL; + } ASSERT(atomic_read(&ip->i_iocount) == 0); ASSERT(atomic_read(&ip->i_pincount) == 0); @@ -105,17 +109,6 @@ xfs_inode_alloc( #ifdef XFS_DIR2_TRACE ip->i_dir_trace = ktrace_alloc(XFS_DIR2_KTRACE_SIZE, KM_NOFS); #endif - /* - * Now initialise the VFS inode. We do this after the xfs_inode - * initialisation as internal failures will result in ->destroy_inode - * being called and that will pass down through the reclaim path and - * free the XFS inode. This path requires the XFS inode to already be - * initialised. Hence if this call fails, the xfs_inode has already - * been freed and we should not reference it at all in the error - * handling. - */ - if (!inode_init_always(mp->m_super, VFS_I(ip))) - return NULL; /* prevent anyone from using this yet */ VFS_I(ip)->i_state = I_NEW|I_LOCK; @@ -167,7 +160,7 @@ xfs_iget_cache_hit( * errors cleanly, then tag it so it can be set up correctly * later. */ - if (!inode_init_always(mp->m_super, VFS_I(ip))) { + if (inode_init_always(mp->m_super, VFS_I(ip))) { error = ENOMEM; goto out_error; } diff --git a/include/linux/fs.h b/include/linux/fs.h index a36ffa5a77a..0c3b5e58a98 100644 --- a/include/linux/fs.h +++ b/include/linux/fs.h @@ -2137,7 +2137,7 @@ extern loff_t default_llseek(struct file *file, loff_t offset, int origin); extern loff_t vfs_llseek(struct file *file, loff_t offset, int origin); -extern struct inode * inode_init_always(struct super_block *, struct inode *); +extern int inode_init_always(struct super_block *, struct inode *); extern void inode_init_once(struct inode *); extern void inode_add_to_lists(struct super_block *, struct inode *); extern void iput(struct inode *); -- GitLab From 2e00c97e2c1d2ffc9e26252ca26b237678b0b772 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Fri, 7 Aug 2009 14:38:29 -0300 Subject: [PATCH 0890/1342] vfs: add __destroy_inode When we want to tear down an inode that lost the add to the cache race in XFS we must not call into ->destroy_inode because that would delete the inode that won the race from the inode cache radix tree. This patch provides the __destroy_inode helper needed to fix this, the actual fix will be in th next patch. As XFS was the only reason destroy_inode was exported we shift the export to the new __destroy_inode. Signed-off-by: Christoph Hellwig Reviewed-by: Eric Sandeen --- fs/inode.c | 10 +++++++--- include/linux/fs.h | 1 + 2 files changed, 8 insertions(+), 3 deletions(-) diff --git a/fs/inode.c b/fs/inode.c index af2c05235cc..ae7b67e4866 100644 --- a/fs/inode.c +++ b/fs/inode.c @@ -229,7 +229,7 @@ static struct inode *alloc_inode(struct super_block *sb) return inode; } -void destroy_inode(struct inode *inode) +void __destroy_inode(struct inode *inode) { BUG_ON(inode_has_buffers(inode)); ima_inode_free(inode); @@ -241,13 +241,17 @@ void destroy_inode(struct inode *inode) if (inode->i_default_acl && inode->i_default_acl != ACL_NOT_CACHED) posix_acl_release(inode->i_default_acl); #endif +} +EXPORT_SYMBOL(__destroy_inode); + +void destroy_inode(struct inode *inode) +{ + __destroy_inode(inode); if (inode->i_sb->s_op->destroy_inode) inode->i_sb->s_op->destroy_inode(inode); else kmem_cache_free(inode_cachep, (inode)); } -EXPORT_SYMBOL(destroy_inode); - /* * These are initializations that only need to be done diff --git a/include/linux/fs.h b/include/linux/fs.h index 0c3b5e58a98..67888a9e065 100644 --- a/include/linux/fs.h +++ b/include/linux/fs.h @@ -2164,6 +2164,7 @@ extern void __iget(struct inode * inode); extern void iget_failed(struct inode *); extern void clear_inode(struct inode *); extern void destroy_inode(struct inode *); +extern void __destroy_inode(struct inode *); extern struct inode *new_inode(struct super_block *); extern int should_remove_suid(struct dentry *); extern int file_remove_suid(struct file *); -- GitLab From b36ec0428a06fcbdb67d61e9e664154e5dd9a8c7 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Fri, 7 Aug 2009 14:38:34 -0300 Subject: [PATCH 0891/1342] xfs: fix freeing of inodes not yet added to the inode cache When freeing an inode that lost race getting added to the inode cache we must not call into ->destroy_inode, because that would delete the inode that won the race from the inode cache radix tree. This patch uses splits a new xfs_inode_free helper out of xfs_ireclaim and uses that plus __destroy_inode to make sure we really only free the memory allocted for the inode that lost the race, and not mess with the inode cache state. Signed-off-by: Christoph Hellwig Reviewed-by: Eric Sandeen Reported-by: Alex Samad Reported-by: Andrew Randrianasulu Reported-by: Stephane Reported-by: Tommy Reported-by: Miah Gregory Reported-by: Gabriel Barazer Reported-by: Leandro Lucarella Reported-by: Daniel Burr Reported-by: Nickolay Reported-by: Michael Guntsche Reported-by: Dan Carley Reported-by: Michael Ole Olsen Reported-by: Michael Weissenbacher Reported-by: Martin Spott Reported-by: Christian Kujau Tested-by: Michael Guntsche Tested-by: Dan Carley Tested-by: Christian Kujau --- fs/xfs/xfs_iget.c | 125 ++++++++++++++++++++++++--------------------- fs/xfs/xfs_inode.h | 17 ------ 2 files changed, 68 insertions(+), 74 deletions(-) diff --git a/fs/xfs/xfs_iget.c b/fs/xfs/xfs_iget.c index 719c85b155f..34ec86923f7 100644 --- a/fs/xfs/xfs_iget.c +++ b/fs/xfs/xfs_iget.c @@ -116,6 +116,71 @@ xfs_inode_alloc( return ip; } +STATIC void +xfs_inode_free( + struct xfs_inode *ip) +{ + switch (ip->i_d.di_mode & S_IFMT) { + case S_IFREG: + case S_IFDIR: + case S_IFLNK: + xfs_idestroy_fork(ip, XFS_DATA_FORK); + break; + } + + if (ip->i_afp) + xfs_idestroy_fork(ip, XFS_ATTR_FORK); + +#ifdef XFS_INODE_TRACE + ktrace_free(ip->i_trace); +#endif +#ifdef XFS_BMAP_TRACE + ktrace_free(ip->i_xtrace); +#endif +#ifdef XFS_BTREE_TRACE + ktrace_free(ip->i_btrace); +#endif +#ifdef XFS_RW_TRACE + ktrace_free(ip->i_rwtrace); +#endif +#ifdef XFS_ILOCK_TRACE + ktrace_free(ip->i_lock_trace); +#endif +#ifdef XFS_DIR2_TRACE + ktrace_free(ip->i_dir_trace); +#endif + + if (ip->i_itemp) { + /* + * Only if we are shutting down the fs will we see an + * inode still in the AIL. If it is there, we should remove + * it to prevent a use-after-free from occurring. + */ + xfs_log_item_t *lip = &ip->i_itemp->ili_item; + struct xfs_ail *ailp = lip->li_ailp; + + ASSERT(((lip->li_flags & XFS_LI_IN_AIL) == 0) || + XFS_FORCED_SHUTDOWN(ip->i_mount)); + if (lip->li_flags & XFS_LI_IN_AIL) { + spin_lock(&ailp->xa_lock); + if (lip->li_flags & XFS_LI_IN_AIL) + xfs_trans_ail_delete(ailp, lip); + else + spin_unlock(&ailp->xa_lock); + } + xfs_inode_item_destroy(ip); + ip->i_itemp = NULL; + } + + /* asserts to verify all state is correct here */ + ASSERT(atomic_read(&ip->i_iocount) == 0); + ASSERT(atomic_read(&ip->i_pincount) == 0); + ASSERT(!spin_is_locked(&ip->i_flags_lock)); + ASSERT(completion_done(&ip->i_flush)); + + kmem_zone_free(xfs_inode_zone, ip); +} + /* * Check the validity of the inode we just found it the cache */ @@ -292,7 +357,8 @@ out_preload_end: if (lock_flags) xfs_iunlock(ip, lock_flags); out_destroy: - xfs_destroy_inode(ip); + __destroy_inode(VFS_I(ip)); + xfs_inode_free(ip); return error; } @@ -497,62 +563,7 @@ xfs_ireclaim( xfs_qm_dqdetach(ip); xfs_iunlock(ip, XFS_ILOCK_EXCL | XFS_IOLOCK_EXCL); - switch (ip->i_d.di_mode & S_IFMT) { - case S_IFREG: - case S_IFDIR: - case S_IFLNK: - xfs_idestroy_fork(ip, XFS_DATA_FORK); - break; - } - - if (ip->i_afp) - xfs_idestroy_fork(ip, XFS_ATTR_FORK); - -#ifdef XFS_INODE_TRACE - ktrace_free(ip->i_trace); -#endif -#ifdef XFS_BMAP_TRACE - ktrace_free(ip->i_xtrace); -#endif -#ifdef XFS_BTREE_TRACE - ktrace_free(ip->i_btrace); -#endif -#ifdef XFS_RW_TRACE - ktrace_free(ip->i_rwtrace); -#endif -#ifdef XFS_ILOCK_TRACE - ktrace_free(ip->i_lock_trace); -#endif -#ifdef XFS_DIR2_TRACE - ktrace_free(ip->i_dir_trace); -#endif - if (ip->i_itemp) { - /* - * Only if we are shutting down the fs will we see an - * inode still in the AIL. If it is there, we should remove - * it to prevent a use-after-free from occurring. - */ - xfs_log_item_t *lip = &ip->i_itemp->ili_item; - struct xfs_ail *ailp = lip->li_ailp; - - ASSERT(((lip->li_flags & XFS_LI_IN_AIL) == 0) || - XFS_FORCED_SHUTDOWN(ip->i_mount)); - if (lip->li_flags & XFS_LI_IN_AIL) { - spin_lock(&ailp->xa_lock); - if (lip->li_flags & XFS_LI_IN_AIL) - xfs_trans_ail_delete(ailp, lip); - else - spin_unlock(&ailp->xa_lock); - } - xfs_inode_item_destroy(ip); - ip->i_itemp = NULL; - } - /* asserts to verify all state is correct here */ - ASSERT(atomic_read(&ip->i_iocount) == 0); - ASSERT(atomic_read(&ip->i_pincount) == 0); - ASSERT(!spin_is_locked(&ip->i_flags_lock)); - ASSERT(completion_done(&ip->i_flush)); - kmem_zone_free(xfs_inode_zone, ip); + xfs_inode_free(ip); } /* diff --git a/fs/xfs/xfs_inode.h b/fs/xfs/xfs_inode.h index 1804f866a71..65f24a3cc99 100644 --- a/fs/xfs/xfs_inode.h +++ b/fs/xfs/xfs_inode.h @@ -309,23 +309,6 @@ static inline struct inode *VFS_I(struct xfs_inode *ip) return &ip->i_vnode; } -/* - * Get rid of a partially initialized inode. - * - * We have to go through destroy_inode to make sure allocations - * from init_inode_always like the security data are undone. - * - * We mark the inode bad so that it takes the short cut in - * the reclaim path instead of going through the flush path - * which doesn't make sense for an inode that has never seen the - * light of day. - */ -static inline void xfs_destroy_inode(struct xfs_inode *ip) -{ - make_bad_inode(VFS_I(ip)); - return destroy_inode(VFS_I(ip)); -} - /* * i_flags helper functions */ -- GitLab From 2020002a878403a6858868d85a43623f74859dba Mon Sep 17 00:00:00 2001 From: Stoyan Gaydarov Date: Thu, 6 Aug 2009 15:07:28 -0700 Subject: [PATCH 0892/1342] drivers/w1/masters/omap_hdq.c: fix missing mutex unlock This was found using a semantic patch, more info can be found at: http://www.emn.fr/x-info/coccinelle/ Signed-off-by: Stoyan Gaydarov Acked-by: Evgeniy Polyakov Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/w1/masters/omap_hdq.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/w1/masters/omap_hdq.c b/drivers/w1/masters/omap_hdq.c index a7e3b706b9d..0d92969404c 100644 --- a/drivers/w1/masters/omap_hdq.c +++ b/drivers/w1/masters/omap_hdq.c @@ -687,6 +687,7 @@ static int omap_hdq_remove(struct platform_device *pdev) if (hdq_data->hdq_usecount) { dev_dbg(&pdev->dev, "removed when use count is not zero\n"); + mutex_unlock(&hdq_data->hdq_mutex); return -EBUSY; } -- GitLab From 69dd647f969c28d18de77e2153f30d05a1874571 Mon Sep 17 00:00:00 2001 From: Xiao Guangrong Date: Thu, 6 Aug 2009 15:07:29 -0700 Subject: [PATCH 0893/1342] generic-ipi: fix hotplug_cfd() Use CONFIG_HOTPLUG_CPU, not CONFIG_CPU_HOTPLUG When hot-unpluging a cpu, it will leak memory allocated at cpu hotplug, but only if CPUMASK_OFFSTACK=y, which is default to n. The bug was introduced by 8969a5ede0f9e17da4b943712429aef2c9bcd82b ("generic-ipi: remove kmalloc()"). Signed-off-by: Xiao Guangrong Cc: Ingo Molnar Cc: Jens Axboe Cc: Nick Piggin Cc: Peter Zijlstra Cc: Rusty Russell Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- kernel/smp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/smp.c b/kernel/smp.c index ad63d850120..94188b8ecc3 100644 --- a/kernel/smp.c +++ b/kernel/smp.c @@ -57,7 +57,7 @@ hotplug_cfd(struct notifier_block *nfb, unsigned long action, void *hcpu) return NOTIFY_BAD; break; -#ifdef CONFIG_CPU_HOTPLUG +#ifdef CONFIG_HOTPLUG_CPU case CPU_UP_CANCELED: case CPU_UP_CANCELED_FROZEN: -- GitLab From 93274e4d4e9416ad1fa47e2f26011e2c483fe5fe Mon Sep 17 00:00:00 2001 From: Stefani Seibold Date: Thu, 6 Aug 2009 15:07:30 -0700 Subject: [PATCH 0894/1342] fbcon: fix rotate upside down crash Fix the rotate_ud() function not to crash in case of a font which has not a width of multiple by 8: The inner loop of the font pixel copy should not access a bit outside the font memory area. Subtract the shift offset from the font width will prevent this. Signed-off-by: Stefani Seibold Cc: Krzysztof Helt Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/console/fbcon_rotate.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/video/console/fbcon_rotate.h b/drivers/video/console/fbcon_rotate.h index 75be5ce53dc..e233444cda6 100644 --- a/drivers/video/console/fbcon_rotate.h +++ b/drivers/video/console/fbcon_rotate.h @@ -45,7 +45,7 @@ static inline void rotate_ud(const char *in, char *out, u32 width, u32 height) width = (width + 7) & ~7; for (i = 0; i < height; i++) { - for (j = 0; j < width; j++) { + for (j = 0; j < width - shift; j++) { if (pattern_test_bit(j, i, width, in)) pattern_set_bit(width - (1 + j + shift), height - (1 + i), -- GitLab From 4bfc44958e499af9a73f62201543b3a1f617cfeb Mon Sep 17 00:00:00 2001 From: KAMEZAWA Hiroyuki Date: Thu, 6 Aug 2009 15:07:33 -0700 Subject: [PATCH 0895/1342] mm: make set_mempolicy(MPOL_INTERLEAV) N_HIGH_MEMORY aware At first, init_task's mems_allowed is initialized as this. init_task->mems_allowed == node_state[N_POSSIBLE] And cpuset's top_cpuset mask is initialized as this top_cpuset->mems_allowed = node_state[N_HIGH_MEMORY] Before 2.6.29: policy's mems_allowed is initialized as this. 1. update tasks->mems_allowed by its cpuset->mems_allowed. 2. policy->mems_allowed = nodes_and(tasks->mems_allowed, user's mask) Updating task's mems_allowed in reference to top_cpuset's one. cpuset's mems_allowed is aware of N_HIGH_MEMORY, always. In 2.6.30: After commit 58568d2a8215cb6f55caf2332017d7bdff954e1c ("cpuset,mm: update tasks' mems_allowed in time"), policy's mems_allowed is initialized as this. 1. policy->mems_allowd = nodes_and(task->mems_allowed, user's mask) Here, if task is in top_cpuset, task->mems_allowed is not updated from init's one. Assume user excutes command as #numactrl --interleave=all ,.... policy->mems_allowd = nodes_and(N_POSSIBLE, ALL_SET_MASK) Then, policy's mems_allowd can includes a possible node, which has no pgdat. MPOL's INTERLEAVE just scans nodemask of task->mems_allowd and access this directly. NODE_DATA(nid)->zonelist even if NODE_DATA(nid)==NULL Then, what's we need is making policy->mems_allowed be aware of N_HIGH_MEMORY. This patch does that. But to do so, extra nodemask will be on statck. Because I know cpumask has a new interface of CPUMASK_ALLOC(), I added it to node. This patch stands on old behavior. But I feel this fix itself is just a Band-Aid. But to do fundametal fix, we have to take care of memory hotplug and it takes time. (task->mems_allowd should be N_HIGH_MEMORY, I think.) mpol_set_nodemask() should be aware of N_HIGH_MEMORY and policy's nodemask should be includes only online nodes. In old behavior, this is guaranteed by frequent reference to cpuset's code. Now, most of them are removed and mempolicy has to check it by itself. To do check, a few nodemask_t will be used for calculating nodemask. But, size of nodemask_t can be big and it's not good to allocate them on stack. Now, cpumask_t has CPUMASK_ALLOC/FREE an easy code for get scratch area. NODEMASK_ALLOC/FREE shoudl be there. [akpm@linux-foundation.org: cleanups & tweaks] Tested-by: KOSAKI Motohiro Signed-off-by: KAMEZAWA Hiroyuki Cc: Miao Xie Cc: Ingo Molnar Cc: Peter Zijlstra Cc: Christoph Lameter Cc: Paul Menage Cc: Nick Piggin Cc: Yasunori Goto Cc: Pekka Enberg Cc: David Rientjes Cc: Lee Schermerhorn Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- include/linux/nodemask.h | 28 ++++++++++++++ mm/mempolicy.c | 84 +++++++++++++++++++++++++++------------- 2 files changed, 86 insertions(+), 26 deletions(-) diff --git a/include/linux/nodemask.h b/include/linux/nodemask.h index 829b94b156f..b359c4a9ec9 100644 --- a/include/linux/nodemask.h +++ b/include/linux/nodemask.h @@ -82,6 +82,12 @@ * to generate slightly worse code. So use a simple one-line #define * for node_isset(), instead of wrapping an inline inside a macro, the * way we do the other calls. + * + * NODEMASK_SCRATCH + * When doing above logical AND, OR, XOR, Remap operations the callers tend to + * need temporary nodemask_t's on the stack. But if NODES_SHIFT is large, + * nodemask_t's consume too much stack space. NODEMASK_SCRATCH is a helper + * for such situations. See below and CPUMASK_ALLOC also. */ #include @@ -473,4 +479,26 @@ static inline int num_node_state(enum node_states state) #define for_each_node(node) for_each_node_state(node, N_POSSIBLE) #define for_each_online_node(node) for_each_node_state(node, N_ONLINE) +/* + * For nodemask scrach area.(See CPUMASK_ALLOC() in cpumask.h) + */ + +#if NODES_SHIFT > 8 /* nodemask_t > 64 bytes */ +#define NODEMASK_ALLOC(x, m) struct x *m = kmalloc(sizeof(*m), GFP_KERNEL) +#define NODEMASK_FREE(m) kfree(m) +#else +#define NODEMASK_ALLOC(x, m) struct x _m, *m = &_m +#define NODEMASK_FREE(m) +#endif + +/* A example struture for using NODEMASK_ALLOC, used in mempolicy. */ +struct nodemask_scratch { + nodemask_t mask1; + nodemask_t mask2; +}; + +#define NODEMASK_SCRATCH(x) NODEMASK_ALLOC(nodemask_scratch, x) +#define NODEMASK_SCRATCH_FREE(x) NODEMASK_FREE(x) + + #endif /* __LINUX_NODEMASK_H */ diff --git a/mm/mempolicy.c b/mm/mempolicy.c index e08e2c4da63..7dd9d9f8069 100644 --- a/mm/mempolicy.c +++ b/mm/mempolicy.c @@ -191,25 +191,27 @@ static int mpol_new_bind(struct mempolicy *pol, const nodemask_t *nodes) * Must be called holding task's alloc_lock to protect task's mems_allowed * and mempolicy. May also be called holding the mmap_semaphore for write. */ -static int mpol_set_nodemask(struct mempolicy *pol, const nodemask_t *nodes) +static int mpol_set_nodemask(struct mempolicy *pol, + const nodemask_t *nodes, struct nodemask_scratch *nsc) { - nodemask_t cpuset_context_nmask; int ret; /* if mode is MPOL_DEFAULT, pol is NULL. This is right. */ if (pol == NULL) return 0; + /* Check N_HIGH_MEMORY */ + nodes_and(nsc->mask1, + cpuset_current_mems_allowed, node_states[N_HIGH_MEMORY]); VM_BUG_ON(!nodes); if (pol->mode == MPOL_PREFERRED && nodes_empty(*nodes)) nodes = NULL; /* explicit local allocation */ else { if (pol->flags & MPOL_F_RELATIVE_NODES) - mpol_relative_nodemask(&cpuset_context_nmask, nodes, - &cpuset_current_mems_allowed); + mpol_relative_nodemask(&nsc->mask2, nodes,&nsc->mask1); else - nodes_and(cpuset_context_nmask, *nodes, - cpuset_current_mems_allowed); + nodes_and(nsc->mask2, *nodes, nsc->mask1); + if (mpol_store_user_nodemask(pol)) pol->w.user_nodemask = *nodes; else @@ -217,8 +219,10 @@ static int mpol_set_nodemask(struct mempolicy *pol, const nodemask_t *nodes) cpuset_current_mems_allowed; } - ret = mpol_ops[pol->mode].create(pol, - nodes ? &cpuset_context_nmask : NULL); + if (nodes) + ret = mpol_ops[pol->mode].create(pol, &nsc->mask2); + else + ret = mpol_ops[pol->mode].create(pol, NULL); return ret; } @@ -620,12 +624,17 @@ static long do_set_mempolicy(unsigned short mode, unsigned short flags, { struct mempolicy *new, *old; struct mm_struct *mm = current->mm; + NODEMASK_SCRATCH(scratch); int ret; - new = mpol_new(mode, flags, nodes); - if (IS_ERR(new)) - return PTR_ERR(new); + if (!scratch) + return -ENOMEM; + new = mpol_new(mode, flags, nodes); + if (IS_ERR(new)) { + ret = PTR_ERR(new); + goto out; + } /* * prevent changing our mempolicy while show_numa_maps() * is using it. @@ -635,13 +644,13 @@ static long do_set_mempolicy(unsigned short mode, unsigned short flags, if (mm) down_write(&mm->mmap_sem); task_lock(current); - ret = mpol_set_nodemask(new, nodes); + ret = mpol_set_nodemask(new, nodes, scratch); if (ret) { task_unlock(current); if (mm) up_write(&mm->mmap_sem); mpol_put(new); - return ret; + goto out; } old = current->mempolicy; current->mempolicy = new; @@ -654,7 +663,10 @@ static long do_set_mempolicy(unsigned short mode, unsigned short flags, up_write(&mm->mmap_sem); mpol_put(old); - return 0; + ret = 0; +out: + NODEMASK_SCRATCH_FREE(scratch); + return ret; } /* @@ -1014,12 +1026,20 @@ static long do_mbind(unsigned long start, unsigned long len, if (err) return err; } - down_write(&mm->mmap_sem); - task_lock(current); - err = mpol_set_nodemask(new, nmask); - task_unlock(current); + { + NODEMASK_SCRATCH(scratch); + if (scratch) { + down_write(&mm->mmap_sem); + task_lock(current); + err = mpol_set_nodemask(new, nmask, scratch); + task_unlock(current); + if (err) + up_write(&mm->mmap_sem); + } else + err = -ENOMEM; + NODEMASK_SCRATCH_FREE(scratch); + } if (err) { - up_write(&mm->mmap_sem); mpol_put(new); return err; } @@ -1891,6 +1911,7 @@ restart: * Install non-NULL @mpol in inode's shared policy rb-tree. * On entry, the current task has a reference on a non-NULL @mpol. * This must be released on exit. + * This is called at get_inode() calls and we can use GFP_KERNEL. */ void mpol_shared_policy_init(struct shared_policy *sp, struct mempolicy *mpol) { @@ -1902,19 +1923,24 @@ void mpol_shared_policy_init(struct shared_policy *sp, struct mempolicy *mpol) if (mpol) { struct vm_area_struct pvma; struct mempolicy *new; + NODEMASK_SCRATCH(scratch); + if (!scratch) + return; /* contextualize the tmpfs mount point mempolicy */ new = mpol_new(mpol->mode, mpol->flags, &mpol->w.user_nodemask); if (IS_ERR(new)) { mpol_put(mpol); /* drop our ref on sb mpol */ + NODEMASK_SCRATCH_FREE(scratch); return; /* no valid nodemask intersection */ } task_lock(current); - ret = mpol_set_nodemask(new, &mpol->w.user_nodemask); + ret = mpol_set_nodemask(new, &mpol->w.user_nodemask, scratch); task_unlock(current); mpol_put(mpol); /* drop our ref on sb mpol */ if (ret) { + NODEMASK_SCRATCH_FREE(scratch); mpol_put(new); return; } @@ -1924,6 +1950,7 @@ void mpol_shared_policy_init(struct shared_policy *sp, struct mempolicy *mpol) pvma.vm_end = TASK_SIZE; /* policy covers entire file */ mpol_set_shared_policy(sp, &pvma, new); /* adds ref */ mpol_put(new); /* drop initial ref */ + NODEMASK_SCRATCH_FREE(scratch); } } @@ -2140,13 +2167,18 @@ int mpol_parse_str(char *str, struct mempolicy **mpol, int no_context) err = 1; else { int ret; - - task_lock(current); - ret = mpol_set_nodemask(new, &nodes); - task_unlock(current); - if (ret) + NODEMASK_SCRATCH(scratch); + if (scratch) { + task_lock(current); + ret = mpol_set_nodemask(new, &nodes, scratch); + task_unlock(current); + } else + ret = -ENOMEM; + NODEMASK_SCRATCH_FREE(scratch); + if (ret) { err = 1; - else if (no_context) { + mpol_put(new); + } else if (no_context) { /* save for contextualization */ new->w.user_nodemask = nodes; } -- GitLab From 521594442cc62d1c2af8436a05ab5918b7730b19 Mon Sep 17 00:00:00 2001 From: Florian Tobias Schandinat Date: Thu, 6 Aug 2009 15:07:34 -0700 Subject: [PATCH 0896/1342] viafb: fix rmmod bug This fixes a bug caused by changing pointers (viafb_mode, viafb_mode1) assigned by module_param. It reduces driver complexity by not needlessly changing these vars as they are only read once and removing now superfluous code. On unpatched kernels loading viafb with viafb_mode or viafb_mode1 option used and afterwards unloading it results in: kernel BUG at mm/slub.c:2926! invalid opcode: 0000 [#1] PREEMPT last sysfs file: /sys/devices/virtual/block/loop0/removable Modules linked in: snd_hda_codec_realtek snd_hda_intel snd_hda_codec snd_hwdep snd_pcm rtl8187 snd_timer eeprom_93cx6 mmc_block snd soundcore via_sdmmc fb snd_page_alloc i2c_algo_bit i2c_viapro ehci_hcd uhci_hcd cfbcopyarea mmc_core cfbimgblt cfbfillrect video output [last unloaded: viafb] Pid: 3355, comm: rmmod Not tainted (2.6.31-rc1 #0) EIP: 0060:[] EFLAGS: 00010246 CPU: 0 EIP is at kfree+0x80/0xda EAX: c17c2da0 EBX: dc7edbdc ECX: 0000010f EDX: 00000000 ESI: c102c700 EDI: dc7ed8fa EBP: d703ff2c ESP: d703ff20 DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068 Process rmmod (pid: 3355, ti=d703e000 task=db1412c0 task.ti=d703e000) Stack: dc7edbdc 00000014 00000016 d703ff40 c102c700 dc7f45d4 dc7f45d4 00000880 d703ff4c c103e571 00000000 d703ffac c103e751 66616976 da140062 db89ba80 00000328 d702edf8 db89ba80 d703ff9c c105d0f0 00000200 da14f898 00000014 Call Trace: [] ? destroy_params+0x1e/0x2b [] ? free_module+0xa2/0xd7 [] ? sys_delete_module+0x1ab/0x1da [] ? do_munmap+0x20a/0x225 [] ? sysenter_do_call+0x12/0x26 Code: 10 76 7a 8d 87 00 00 00 40 c1 e8 0c c1 e0 05 03 05 1c 87 41 c1 66 83 38 00 79 03 8b 40 0c 8b 10 84 d2 78 12 66 f7 c2 00 c0 75 04 <0f> 0b eb fe e8 6f 5a fe ff eb 47 8b 55 04 8b 58 0c 9c 5e fa 3b EIP: [] kfree+0x80/0xda SS:ESP 0068:d703ff20 This is caused by the current code changing the pointers assigned by module_param. During unload it tries to free the memory the pointers point at which is now part of an internal structure. The patch simply avoids changing the pointers. This is okay as they are read only once during the initialization process. Signed-off-by: Florian Tobias Schandinat Cc: Scott Fang Cc: Joseph Chan Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/via/hw.c | 4 +- drivers/video/via/lcd.c | 15 ++---- drivers/video/via/viafbdev.c | 101 ++++++++++++++++------------------- drivers/video/via/viafbdev.h | 3 +- 4 files changed, 53 insertions(+), 70 deletions(-) diff --git a/drivers/video/via/hw.c b/drivers/video/via/hw.c index fcd53ceb88f..c8960003f47 100644 --- a/drivers/video/via/hw.c +++ b/drivers/video/via/hw.c @@ -2407,14 +2407,14 @@ int viafb_setmode(int vmode_index, int hor_res, int ver_res, int video_bpp, viafb_dvi_set_mode(viafb_get_mode_index (viaparinfo->tmds_setting_info->h_active, viaparinfo->tmds_setting_info-> - v_active, 1), + v_active), video_bpp1, viaparinfo-> tmds_setting_info->iga_path); } else { viafb_dvi_set_mode(viafb_get_mode_index (viaparinfo->tmds_setting_info->h_active, viaparinfo-> - tmds_setting_info->v_active, 0), + tmds_setting_info->v_active), video_bpp, viaparinfo-> tmds_setting_info->iga_path); } diff --git a/drivers/video/via/lcd.c b/drivers/video/via/lcd.c index 6c7290a6a44..78c6b338794 100644 --- a/drivers/video/via/lcd.c +++ b/drivers/video/via/lcd.c @@ -580,10 +580,7 @@ static void load_lcd_k400_patch_tbl(int set_hres, int set_vres, int reg_num = 0; struct io_reg *lcd_patch_reg = NULL; - if (viaparinfo->lvds_setting_info->iga_path == IGA2) - vmode_index = viafb_get_mode_index(set_hres, set_vres, 1); - else - vmode_index = viafb_get_mode_index(set_hres, set_vres, 0); + vmode_index = viafb_get_mode_index(set_hres, set_vres); switch (panel_id) { /* LCD 800x600 */ case LCD_PANEL_ID1_800X600: @@ -761,10 +758,7 @@ static void load_lcd_p880_patch_tbl(int set_hres, int set_vres, int reg_num = 0; struct io_reg *lcd_patch_reg = NULL; - if (viaparinfo->lvds_setting_info->iga_path == IGA2) - vmode_index = viafb_get_mode_index(set_hres, set_vres, 1); - else - vmode_index = viafb_get_mode_index(set_hres, set_vres, 0); + vmode_index = viafb_get_mode_index(set_hres, set_vres); switch (panel_id) { case LCD_PANEL_ID5_1400X1050: @@ -832,10 +826,7 @@ static void load_lcd_patch_regs(int set_hres, int set_vres, { int vmode_index; - if (viaparinfo->lvds_setting_info->iga_path == IGA2) - vmode_index = viafb_get_mode_index(set_hres, set_vres, 1); - else - vmode_index = viafb_get_mode_index(set_hres, set_vres, 0); + vmode_index = viafb_get_mode_index(set_hres, set_vres); viafb_unlock_crt(); diff --git a/drivers/video/via/viafbdev.c b/drivers/video/via/viafbdev.c index a0fec298216..72833f3334b 100644 --- a/drivers/video/via/viafbdev.c +++ b/drivers/video/via/viafbdev.c @@ -32,7 +32,6 @@ static u32 pseudo_pal[17]; /* video mode */ static char *viafb_mode = "640x480"; static char *viafb_mode1 = "640x480"; -static int viafb_resMode = VIA_RES_640X480; /* Added for specifying active devices.*/ char *viafb_active_dev = ""; @@ -56,47 +55,47 @@ static void viafb_get_video_device(u32 *video_dev_info); /* Mode information */ static const struct viafb_modeinfo viafb_modentry[] = { - {480, 640, VIA_RES_480X640, "480x640"}, - {640, 480, VIA_RES_640X480, "640x480"}, - {800, 480, VIA_RES_800X480, "800x480"}, - {800, 600, VIA_RES_800X600, "800x600"}, - {1024, 768, VIA_RES_1024X768, "1024x768"}, - {1152, 864, VIA_RES_1152X864, "1152x864"}, - {1280, 1024, VIA_RES_1280X1024, "1280x1024"}, - {1600, 1200, VIA_RES_1600X1200, "1600x1200"}, - {1440, 1050, VIA_RES_1440X1050, "1440x1050"}, - {1280, 768, VIA_RES_1280X768, "1280x768"}, - {1280, 800, VIA_RES_1280X800, "1280x800"}, - {1280, 960, VIA_RES_1280X960, "1280x960"}, - {1920, 1440, VIA_RES_1920X1440, "1920x1440"}, - {848, 480, VIA_RES_848X480, "848x480"}, - {1400, 1050, VIA_RES_1400X1050, "1400x1050"}, - {720, 480, VIA_RES_720X480, "720x480"}, - {720, 576, VIA_RES_720X576, "720x576"}, - {1024, 512, VIA_RES_1024X512, "1024x512"}, - {1024, 576, VIA_RES_1024X576, "1024x576"}, - {1024, 600, VIA_RES_1024X600, "1024x600"}, - {1280, 720, VIA_RES_1280X720, "1280x720"}, - {1920, 1080, VIA_RES_1920X1080, "1920x1080"}, - {1366, 768, VIA_RES_1368X768, "1368x768"}, - {1680, 1050, VIA_RES_1680X1050, "1680x1050"}, - {960, 600, VIA_RES_960X600, "960x600"}, - {1000, 600, VIA_RES_1000X600, "1000x600"}, - {1024, 576, VIA_RES_1024X576, "1024x576"}, - {1024, 600, VIA_RES_1024X600, "1024x600"}, - {1088, 612, VIA_RES_1088X612, "1088x612"}, - {1152, 720, VIA_RES_1152X720, "1152x720"}, - {1200, 720, VIA_RES_1200X720, "1200x720"}, - {1280, 600, VIA_RES_1280X600, "1280x600"}, - {1360, 768, VIA_RES_1360X768, "1360x768"}, - {1440, 900, VIA_RES_1440X900, "1440x900"}, - {1600, 900, VIA_RES_1600X900, "1600x900"}, - {1600, 1024, VIA_RES_1600X1024, "1600x1024"}, - {1792, 1344, VIA_RES_1792X1344, "1792x1344"}, - {1856, 1392, VIA_RES_1856X1392, "1856x1392"}, - {1920, 1200, VIA_RES_1920X1200, "1920x1200"}, - {2048, 1536, VIA_RES_2048X1536, "2048x1536"}, - {0, 0, VIA_RES_INVALID, "640x480"} + {480, 640, VIA_RES_480X640}, + {640, 480, VIA_RES_640X480}, + {800, 480, VIA_RES_800X480}, + {800, 600, VIA_RES_800X600}, + {1024, 768, VIA_RES_1024X768}, + {1152, 864, VIA_RES_1152X864}, + {1280, 1024, VIA_RES_1280X1024}, + {1600, 1200, VIA_RES_1600X1200}, + {1440, 1050, VIA_RES_1440X1050}, + {1280, 768, VIA_RES_1280X768,}, + {1280, 800, VIA_RES_1280X800}, + {1280, 960, VIA_RES_1280X960}, + {1920, 1440, VIA_RES_1920X1440}, + {848, 480, VIA_RES_848X480}, + {1400, 1050, VIA_RES_1400X1050}, + {720, 480, VIA_RES_720X480}, + {720, 576, VIA_RES_720X576}, + {1024, 512, VIA_RES_1024X512}, + {1024, 576, VIA_RES_1024X576}, + {1024, 600, VIA_RES_1024X600}, + {1280, 720, VIA_RES_1280X720}, + {1920, 1080, VIA_RES_1920X1080}, + {1366, 768, VIA_RES_1368X768}, + {1680, 1050, VIA_RES_1680X1050}, + {960, 600, VIA_RES_960X600}, + {1000, 600, VIA_RES_1000X600}, + {1024, 576, VIA_RES_1024X576}, + {1024, 600, VIA_RES_1024X600}, + {1088, 612, VIA_RES_1088X612}, + {1152, 720, VIA_RES_1152X720}, + {1200, 720, VIA_RES_1200X720}, + {1280, 600, VIA_RES_1280X600}, + {1360, 768, VIA_RES_1360X768}, + {1440, 900, VIA_RES_1440X900}, + {1600, 900, VIA_RES_1600X900}, + {1600, 1024, VIA_RES_1600X1024}, + {1792, 1344, VIA_RES_1792X1344}, + {1856, 1392, VIA_RES_1856X1392}, + {1920, 1200, VIA_RES_1920X1200}, + {2048, 1536, VIA_RES_2048X1536}, + {0, 0, VIA_RES_INVALID} }; static struct fb_ops viafb_ops; @@ -177,7 +176,7 @@ static int viafb_check_var(struct fb_var_screeninfo *var, if (var->vmode & FB_VMODE_INTERLACED || var->vmode & FB_VMODE_DOUBLE) return -EINVAL; - vmode_index = viafb_get_mode_index(var->xres, var->yres, 0); + vmode_index = viafb_get_mode_index(var->xres, var->yres); if (vmode_index == VIA_RES_INVALID) { DEBUG_MSG(KERN_INFO "viafb: Mode %dx%dx%d not supported!!\n", @@ -233,14 +232,14 @@ static int viafb_set_par(struct fb_info *info) viafb_update_device_setting(info->var.xres, info->var.yres, info->var.bits_per_pixel, viafb_refresh, 0); - vmode_index = viafb_get_mode_index(info->var.xres, info->var.yres, 0); + vmode_index = viafb_get_mode_index(info->var.xres, info->var.yres); if (viafb_SAMM_ON == 1) { DEBUG_MSG(KERN_INFO "viafb_second_xres = %d, viafb_second_yres = %d, bpp = %d\n", viafb_second_xres, viafb_second_yres, viafb_bpp1); vmode_index1 = viafb_get_mode_index(viafb_second_xres, - viafb_second_yres, 1); + viafb_second_yres); DEBUG_MSG(KERN_INFO "->viafb_SAMM_ON: index=%d\n", vmode_index1); @@ -1262,7 +1261,7 @@ static int viafb_sync(struct fb_info *info) return 0; } -int viafb_get_mode_index(int hres, int vres, int flag) +int viafb_get_mode_index(int hres, int vres) { u32 i; DEBUG_MSG(KERN_INFO "viafb_get_mode_index!\n"); @@ -1272,13 +1271,7 @@ int viafb_get_mode_index(int hres, int vres, int flag) viafb_modentry[i].yres == vres) break; - viafb_resMode = viafb_modentry[i].mode_index; - if (flag) - viafb_mode1 = viafb_modentry[i].mode_res; - else - viafb_mode = viafb_modentry[i].mode_res; - - return viafb_resMode; + return viafb_modentry[i].mode_index; } static void check_available_device_to_enable(int device_id) @@ -2199,7 +2192,7 @@ static int __devinit via_pci_probe(void) strict_strtoul(tmpc, 0, &default_xres); strict_strtoul(tmpm, 0, &default_yres); - vmode_index = viafb_get_mode_index(default_xres, default_yres, 0); + vmode_index = viafb_get_mode_index(default_xres, default_yres); DEBUG_MSG(KERN_INFO "0->index=%d\n", vmode_index); if (viafb_SAMM_ON == 1) { diff --git a/drivers/video/via/viafbdev.h b/drivers/video/via/viafbdev.h index a4158e87287..227b000feb3 100644 --- a/drivers/video/via/viafbdev.h +++ b/drivers/video/via/viafbdev.h @@ -81,7 +81,6 @@ struct viafb_modeinfo { u32 xres; u32 yres; int mode_index; - char *mode_res; }; extern unsigned int viafb_second_virtual_yres; extern unsigned int viafb_second_virtual_xres; @@ -102,7 +101,7 @@ extern int strict_strtoul(const char *cp, unsigned int base, void viafb_memory_pitch_patch(struct fb_info *info); void viafb_fill_var_timing_info(struct fb_var_screeninfo *var, int refresh, int mode_index); -int viafb_get_mode_index(int hres, int vres, int flag); +int viafb_get_mode_index(int hres, int vres); u8 viafb_gpio_i2c_read_lvds(struct lvds_setting_information *plvds_setting_info, struct lvds_chip_information *plvds_chip_info, u8 index); -- GitLab From 0035fe00f77d2b0a1a2d001f7442136d1ec5aefa Mon Sep 17 00:00:00 2001 From: Johannes Weiner Date: Thu, 6 Aug 2009 15:07:36 -0700 Subject: [PATCH 0897/1342] fbcon: don't use vc_resize() on initialization Catalin and kmemleak spotted a leak of a VC screen buffer in vc_allocate() due to the following chain of events: vc_allocate() visual_init(init=1) vc->vc_sw->con_init(init=1) fbcon_init() vc_resize() vc->screen_buf = kmalloc() vc->screen_buf = kmalloc() The common way for the VC drivers is to set the screen dimension parameters manually in the init case and only call vc_resize() for !init - which allocates a screen buffer according to the new dimensions. fbcon instead would do vc_resize() unconditionally and afterwards set the dimensions manually (again) for !init - i.e. completely upside down. The vc_resize() allocated buffer would then get lost by vc_allocate() allocating a fresh one. Use vc_resize() only for actual resizing to close the leak. Set the dimensions manually only in initialization mode to remove the redundant setting in resize mode. The kmemleak trace from Catalin: unreferenced object 0xde158000 (size 12288): comm "Xorg", pid 1439, jiffies 4294961016 hex dump (first 32 bytes): 20 00 20 00 20 00 20 00 20 00 20 00 20 00 20 00 . . . . . . . . 20 00 20 00 20 00 20 00 20 00 20 00 20 00 20 00 . . . . . . . . backtrace: [] __save_stack_trace+0x17/0x1c [] create_object+0xcd/0x188 [] kmemleak_alloc+0x1b/0x3c [] __kmalloc+0xdb/0xe8 [] vc_do_resize+0x73/0x1e0 [] vc_resize+0x15/0x18 [] fbcon_init+0x1f9/0x2b8 [] visual_init+0x9f/0xdc [] vc_allocate+0x7f/0xfc [] con_open+0x17/0x80 [] tty_open+0x1f7/0x2e4 [] chrdev_open+0x101/0x118 [] __dentry_open+0x105/0x1cc [] nameidata_to_filp+0x2d/0x38 [] do_filp_open+0x2c1/0x54c [] do_sys_open+0x3b/0xb4 Reported-by: Catalin Marinas Signed-off-by: Johannes Weiner Tested-by: Catalin Marinas Cc: Pekka Enberg Cc: Krzysztof Helt Tested-by: Dave Young Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/console/fbcon.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/video/console/fbcon.c b/drivers/video/console/fbcon.c index 471a9a60376..3a44695b9c0 100644 --- a/drivers/video/console/fbcon.c +++ b/drivers/video/console/fbcon.c @@ -1082,7 +1082,6 @@ static void fbcon_init(struct vc_data *vc, int init) new_rows = FBCON_SWAP(ops->rotate, info->var.yres, info->var.xres); new_cols /= vc->vc_font.width; new_rows /= vc->vc_font.height; - vc_resize(vc, new_cols, new_rows); /* * We must always set the mode. The mode of the previous console @@ -1111,10 +1110,11 @@ static void fbcon_init(struct vc_data *vc, int init) * vc_{cols,rows}, but we must not set those if we are only * resizing the console. */ - if (!init) { + if (init) { vc->vc_cols = new_cols; vc->vc_rows = new_rows; - } + } else + vc_resize(vc, new_cols, new_rows); if (logo) fbcon_prepare_logo(vc, info, cols, rows, new_cols, new_rows); -- GitLab From 69130c7cf96ea853dc5be599dd6a4b98907d39cc Mon Sep 17 00:00:00 2001 From: Eric Sandeen Date: Thu, 6 Aug 2009 15:07:37 -0700 Subject: [PATCH 0898/1342] compat_ioctl: hook up compat handler for FIEMAP ioctl The FIEMAP_IOC_FIEMAP mapping ioctl was missing a 32-bit compat handler, which means that 32-bit suerspace on 64-bit kernels cannot use this ioctl command. The structure is nicely aligned, padded, and sized, so it is just this simple. Tested w/ 32-bit ioctl tester (from Josef) on a 64-bit kernel on ext4. Signed-off-by: Eric Sandeen Cc: Cc: Mark Lord Cc: Arnd Bergmann Cc: Josef Bacik Cc: Jan Kara Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- fs/compat_ioctl.c | 1 + 1 file changed, 1 insertion(+) diff --git a/fs/compat_ioctl.c b/fs/compat_ioctl.c index f28f070a60f..f91fd51b32e 100644 --- a/fs/compat_ioctl.c +++ b/fs/compat_ioctl.c @@ -1905,6 +1905,7 @@ COMPATIBLE_IOCTL(FIONCLEX) COMPATIBLE_IOCTL(FIOASYNC) COMPATIBLE_IOCTL(FIONBIO) COMPATIBLE_IOCTL(FIONREAD) /* This is also TIOCINQ */ +COMPATIBLE_IOCTL(FS_IOC_FIEMAP) /* 0x00 */ COMPATIBLE_IOCTL(FIBMAP) COMPATIBLE_IOCTL(FIGETBSZ) -- GitLab From 2d8dd38a5aa0cc2490bbad9b75e77fa154e1d145 Mon Sep 17 00:00:00 2001 From: OGAWA Hirofumi Date: Thu, 6 Aug 2009 15:07:39 -0700 Subject: [PATCH 0899/1342] vfs: mnt_want_write_file(): fix special file handling I suspect that mnt_want_write_file() may have wrong assumption. I think mnt_want_write_file() is assuming it increments ->mnt_writers if (file->f_mode & FMODE_WRITE). But, if it's special_file(), it is false? Signed-off-by: OGAWA Hirofumi Acked-by: Dave Hansen Cc: Al Viro Cc: Nick Piggin Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- fs/namespace.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/fs/namespace.c b/fs/namespace.c index 277c28a63ea..7230787d18b 100644 --- a/fs/namespace.c +++ b/fs/namespace.c @@ -316,7 +316,8 @@ EXPORT_SYMBOL_GPL(mnt_clone_write); */ int mnt_want_write_file(struct file *file) { - if (!(file->f_mode & FMODE_WRITE)) + struct inode *inode = file->f_dentry->d_inode; + if (!(file->f_mode & FMODE_WRITE) || special_file(inode->i_mode)) return mnt_want_write(file->f_path.mnt); else return mnt_clone_write(file->f_path.mnt); -- GitLab From 20de03dae54e10271ffd308654dfb4a117f4789d Mon Sep 17 00:00:00 2001 From: Guennadi Liakhovetski Date: Thu, 6 Aug 2009 15:07:40 -0700 Subject: [PATCH 0900/1342] i.MX31: fix framebuffer locking regressions Recent framebuffer locking patches first made affected systems unbootable, then the dead-lock has been fixed but as of 2.6.31-rc4 the framebuffer on mx3 machines doesn't work. Fix this. Signed-off-by: Guennadi Liakhovetski Cc: Sascha Hauer Cc: Krzysztof Helt Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/mx3fb.c | 86 ++++++++++++++++++++++++++++--------------- 1 file changed, 56 insertions(+), 30 deletions(-) diff --git a/drivers/video/mx3fb.c b/drivers/video/mx3fb.c index f8778cde218..054ef29be47 100644 --- a/drivers/video/mx3fb.c +++ b/drivers/video/mx3fb.c @@ -669,7 +669,8 @@ static uint32_t bpp_to_pixfmt(int bpp) } static int mx3fb_blank(int blank, struct fb_info *fbi); -static int mx3fb_map_video_memory(struct fb_info *fbi, unsigned int mem_len); +static int mx3fb_map_video_memory(struct fb_info *fbi, unsigned int mem_len, + bool lock); static int mx3fb_unmap_video_memory(struct fb_info *fbi); /** @@ -711,12 +712,7 @@ static void mx3fb_dma_done(void *arg) complete(&mx3_fbi->flip_cmpl); } -/** - * mx3fb_set_par() - set framebuffer parameters and change the operating mode. - * @fbi: framebuffer information pointer. - * @return: 0 on success or negative error code on failure. - */ -static int mx3fb_set_par(struct fb_info *fbi) +static int __set_par(struct fb_info *fbi, bool lock) { u32 mem_len; struct ipu_di_signal_cfg sig_cfg; @@ -727,10 +723,6 @@ static int mx3fb_set_par(struct fb_info *fbi) struct idmac_video_param *video = &ichan->params.video; struct scatterlist *sg = mx3_fbi->sg; - dev_dbg(mx3fb->dev, "%s [%c]\n", __func__, list_empty(&ichan->queue) ? '-' : '+'); - - mutex_lock(&mx3_fbi->mutex); - /* Total cleanup */ if (mx3_fbi->txd) sdc_disable_channel(mx3_fbi); @@ -742,10 +734,8 @@ static int mx3fb_set_par(struct fb_info *fbi) if (fbi->fix.smem_start) mx3fb_unmap_video_memory(fbi); - if (mx3fb_map_video_memory(fbi, mem_len) < 0) { - mutex_unlock(&mx3_fbi->mutex); + if (mx3fb_map_video_memory(fbi, mem_len, lock) < 0) return -ENOMEM; - } } sg_init_table(&sg[0], 1); @@ -791,7 +781,6 @@ static int mx3fb_set_par(struct fb_info *fbi) fbi->var.vsync_len, fbi->var.lower_margin + fbi->var.vsync_len, sig_cfg) != 0) { - mutex_unlock(&mx3_fbi->mutex); dev_err(fbi->device, "mx3fb: Error initializing panel.\n"); return -EINVAL; @@ -810,9 +799,30 @@ static int mx3fb_set_par(struct fb_info *fbi) if (mx3_fbi->blank == FB_BLANK_UNBLANK) sdc_enable_channel(mx3_fbi); + return 0; +} + +/** + * mx3fb_set_par() - set framebuffer parameters and change the operating mode. + * @fbi: framebuffer information pointer. + * @return: 0 on success or negative error code on failure. + */ +static int mx3fb_set_par(struct fb_info *fbi) +{ + struct mx3fb_info *mx3_fbi = fbi->par; + struct mx3fb_data *mx3fb = mx3_fbi->mx3fb; + struct idmac_channel *ichan = mx3_fbi->idmac_channel; + int ret; + + dev_dbg(mx3fb->dev, "%s [%c]\n", __func__, list_empty(&ichan->queue) ? '-' : '+'); + + mutex_lock(&mx3_fbi->mutex); + + ret = __set_par(fbi, true); + mutex_unlock(&mx3_fbi->mutex); - return 0; + return ret; } /** @@ -966,21 +976,11 @@ static int mx3fb_setcolreg(unsigned int regno, unsigned int red, return ret; } -/** - * mx3fb_blank() - blank the display. - */ -static int mx3fb_blank(int blank, struct fb_info *fbi) +static void __blank(int blank, struct fb_info *fbi) { struct mx3fb_info *mx3_fbi = fbi->par; struct mx3fb_data *mx3fb = mx3_fbi->mx3fb; - dev_dbg(fbi->device, "%s, blank = %d, base %p, len %u\n", __func__, - blank, fbi->screen_base, fbi->fix.smem_len); - - if (mx3_fbi->blank == blank) - return 0; - - mutex_lock(&mx3_fbi->mutex); mx3_fbi->blank = blank; switch (blank) { @@ -999,6 +999,23 @@ static int mx3fb_blank(int blank, struct fb_info *fbi) sdc_set_brightness(mx3fb, mx3fb->backlight_level); break; } +} + +/** + * mx3fb_blank() - blank the display. + */ +static int mx3fb_blank(int blank, struct fb_info *fbi) +{ + struct mx3fb_info *mx3_fbi = fbi->par; + + dev_dbg(fbi->device, "%s, blank = %d, base %p, len %u\n", __func__, + blank, fbi->screen_base, fbi->fix.smem_len); + + if (mx3_fbi->blank == blank) + return 0; + + mutex_lock(&mx3_fbi->mutex); + __blank(blank, fbi); mutex_unlock(&mx3_fbi->mutex); return 0; @@ -1198,6 +1215,7 @@ static int mx3fb_resume(struct platform_device *pdev) * mx3fb_map_video_memory() - allocates the DRAM memory for the frame buffer. * @fbi: framebuffer information pointer * @mem_len: length of mapped memory + * @lock: do not lock during initialisation * @return: Error code indicating success or failure * * This buffer is remapped into a non-cached, non-buffered, memory region to @@ -1205,7 +1223,8 @@ static int mx3fb_resume(struct platform_device *pdev) * area is remapped, all virtual memory access to the video memory should occur * at the new region. */ -static int mx3fb_map_video_memory(struct fb_info *fbi, unsigned int mem_len) +static int mx3fb_map_video_memory(struct fb_info *fbi, unsigned int mem_len, + bool lock) { int retval = 0; dma_addr_t addr; @@ -1221,10 +1240,12 @@ static int mx3fb_map_video_memory(struct fb_info *fbi, unsigned int mem_len) goto err0; } - mutex_lock(&fbi->mm_lock); + if (lock) + mutex_lock(&fbi->mm_lock); fbi->fix.smem_start = addr; fbi->fix.smem_len = mem_len; - mutex_unlock(&fbi->mm_lock); + if (lock) + mutex_unlock(&fbi->mm_lock); dev_dbg(fbi->device, "allocated fb @ p=0x%08x, v=0x%p, size=%d.\n", (uint32_t) fbi->fix.smem_start, fbi->screen_base, fbi->fix.smem_len); @@ -1365,6 +1386,11 @@ static int init_fb_chan(struct mx3fb_data *mx3fb, struct idmac_channel *ichan) init_completion(&mx3fbi->flip_cmpl); disable_irq(ichan->eof_irq); dev_dbg(mx3fb->dev, "disabling irq %d\n", ichan->eof_irq); + ret = __set_par(fbi, false); + if (ret < 0) + goto esetpar; + + __blank(FB_BLANK_UNBLANK, fbi); dev_info(dev, "registered, using mode %s\n", fb_mode); -- GitLab From 2198a64a7487aba036f71998ade8a6528070d32c Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Thu, 6 Aug 2009 15:07:41 -0700 Subject: [PATCH 0901/1342] drivers/mmc: correct error-handling code sdhci_alloc_host returns an ERR_PTR value in an error case instead of NULL. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // @match exists@ expression x, E; statement S1, S2; @@ x = sdhci_alloc_host(...) ... when != x = E ( * if (x == NULL || ...) S1 else S2 | * if (x == NULL && ...) S1 else S2 ) // Signed-off-by: Julia Lawall Acked-by: Anton Vorontsov Cc: Matt Fleming Cc: Ian Molton Cc: "Roberto A. Foglietta" Cc: Philip Langdale Cc: Pierre Ossman Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/mmc/host/sdhci-of.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/mmc/host/sdhci-of.c b/drivers/mmc/host/sdhci-of.c index 908844327db..1e8aa590bb3 100644 --- a/drivers/mmc/host/sdhci-of.c +++ b/drivers/mmc/host/sdhci-of.c @@ -234,7 +234,7 @@ static int __devinit sdhci_of_probe(struct of_device *ofdev, return -ENODEV; host = sdhci_alloc_host(&ofdev->dev, sizeof(*of_host)); - if (!host) + if (IS_ERR(host)) return -ENOMEM; of_host = sdhci_priv(host); -- GitLab From 9c8a8228d0827e0d91d28527209988f672f97d28 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Thu, 6 Aug 2009 15:09:28 -0700 Subject: [PATCH 0902/1342] execve: must clear current->clear_child_tid While looking at Jens Rosenboom bug report (http://lkml.org/lkml/2009/7/27/35) about strange sys_futex call done from a dying "ps" program, we found following problem. clone() syscall has special support for TID of created threads. This support includes two features. One (CLONE_CHILD_SETTID) is to set an integer into user memory with the TID value. One (CLONE_CHILD_CLEARTID) is to clear this same integer once the created thread dies. The integer location is a user provided pointer, provided at clone() time. kernel keeps this pointer value into current->clear_child_tid. At execve() time, we should make sure kernel doesnt keep this user provided pointer, as full user memory is replaced by a new one. As glibc fork() actually uses clone() syscall with CLONE_CHILD_SETTID and CLONE_CHILD_CLEARTID set, chances are high that we might corrupt user memory in forked processes. Following sequence could happen: 1) bash (or any program) starts a new process, by a fork() call that glibc maps to a clone( ... CLONE_CHILD_SETTID | CLONE_CHILD_CLEARTID ...) syscall 2) When new process starts, its current->clear_child_tid is set to a location that has a meaning only in bash (or initial program) context (&THREAD_SELF->tid) 3) This new process does the execve() syscall to start a new program. current->clear_child_tid is left unchanged (a non NULL value) 4) If this new program creates some threads, and initial thread exits, kernel will attempt to clear the integer pointed by current->clear_child_tid from mm_release() : if (tsk->clear_child_tid && !(tsk->flags & PF_SIGNALED) && atomic_read(&mm->mm_users) > 1) { u32 __user * tidptr = tsk->clear_child_tid; tsk->clear_child_tid = NULL; /* * We don't check the error code - if userspace has * not set up a proper pointer then tough luck. */ << here >> put_user(0, tidptr); sys_futex(tidptr, FUTEX_WAKE, 1, NULL, NULL, 0); } 5) OR : if new program is not multi-threaded, but spied by /proc/pid users (ps command for example), mm_users > 1, and the exiting program could corrupt 4 bytes in a persistent memory area (shm or memory mapped file) If current->clear_child_tid points to a writeable portion of memory of the new program, kernel happily and silently corrupts 4 bytes of memory, with unexpected effects. Fix is straightforward and should not break any sane program. Reported-by: Jens Rosenboom Acked-by: Linus Torvalds Signed-off-by: Eric Dumazet Signed-off-by: Oleg Nesterov Cc: Peter Zijlstra Cc: Sonny Rao Cc: Ingo Molnar Cc: Thomas Gleixner Cc: Ulrich Drepper Cc: Oleg Nesterov Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- kernel/fork.c | 22 +++++++++++----------- 1 file changed, 11 insertions(+), 11 deletions(-) diff --git a/kernel/fork.c b/kernel/fork.c index 466531eb92c..021e1138556 100644 --- a/kernel/fork.c +++ b/kernel/fork.c @@ -568,18 +568,18 @@ void mm_release(struct task_struct *tsk, struct mm_struct *mm) * the value intact in a core dump, and to save the unnecessary * trouble otherwise. Userland only wants this done for a sys_exit. */ - if (tsk->clear_child_tid - && !(tsk->flags & PF_SIGNALED) - && atomic_read(&mm->mm_users) > 1) { - u32 __user * tidptr = tsk->clear_child_tid; + if (tsk->clear_child_tid) { + if (!(tsk->flags & PF_SIGNALED) && + atomic_read(&mm->mm_users) > 1) { + /* + * We don't check the error code - if userspace has + * not set up a proper pointer then tough luck. + */ + put_user(0, tsk->clear_child_tid); + sys_futex(tsk->clear_child_tid, FUTEX_WAKE, + 1, NULL, NULL, 0); + } tsk->clear_child_tid = NULL; - - /* - * We don't check the error code - if userspace has - * not set up a proper pointer then tough luck. - */ - put_user(0, tidptr); - sys_futex(tidptr, FUTEX_WAKE, 1, NULL, NULL, 0); } } -- GitLab From daeb6b6fbe27049f465c48a7d0ee5555c3b84064 Mon Sep 17 00:00:00 2001 From: Phillip Lougher Date: Thu, 6 Aug 2009 15:09:30 -0700 Subject: [PATCH 0903/1342] bzip2/lzma/gzip: fix comments describing decompressor API Fix and improve comments in decompress/generic.h that describe the decompressor API. Also remove an unused definition, and rename INBUF_LEN in lib/decompress_inflate.c to conform to bzip2/lzma naming. Signed-off-by: Phillip Lougher Cc: "H. Peter Anvin" Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- include/linux/decompress/generic.h | 32 ++++++++++++++++++------------ lib/decompress_inflate.c | 8 ++++---- 2 files changed, 23 insertions(+), 17 deletions(-) diff --git a/include/linux/decompress/generic.h b/include/linux/decompress/generic.h index 6dfb856327b..0c7111a55a1 100644 --- a/include/linux/decompress/generic.h +++ b/include/linux/decompress/generic.h @@ -1,31 +1,37 @@ #ifndef DECOMPRESS_GENERIC_H #define DECOMPRESS_GENERIC_H -/* Minimal chunksize to be read. - *Bzip2 prefers at least 4096 - *Lzma prefers 0x10000 */ -#define COMPR_IOBUF_SIZE 4096 - typedef int (*decompress_fn) (unsigned char *inbuf, int len, int(*fill)(void*, unsigned int), - int(*writebb)(void*, unsigned int), - unsigned char *output, + int(*flush)(void*, unsigned int), + unsigned char *outbuf, int *posp, void(*error)(char *x)); /* inbuf - input buffer *len - len of pre-read data in inbuf - *fill - function to fill inbuf if empty - *writebb - function to write out outbug + *fill - function to fill inbuf when empty + *flush - function to write out outbuf + *outbuf - output buffer *posp - if non-null, input position (number of bytes read) will be * returned here * - *If len != 0, the inbuf is initialized (with as much data), and fill - *should not be called - *If len = 0, the inbuf is allocated, but empty. Its size is IOBUF_SIZE - *fill should be called (repeatedly...) to read data, at most IOBUF_SIZE + *If len != 0, inbuf should contain all the necessary input data, and fill + *should be NULL + *If len = 0, inbuf can be NULL, in which case the decompressor will allocate + *the input buffer. If inbuf != NULL it must be at least XXX_IOBUF_SIZE bytes. + *fill will be called (repeatedly...) to read data, at most XXX_IOBUF_SIZE + *bytes should be read per call. Replace XXX with the appropriate decompressor + *name, i.e. LZMA_IOBUF_SIZE. + * + *If flush = NULL, outbuf must be large enough to buffer all the expected + *output. If flush != NULL, the output buffer will be allocated by the + *decompressor (outbuf = NULL), and the flush function will be called to + *flush the output buffer at the appropriate time (decompressor and stream + *dependent). */ + /* Utility routine to detect the decompression method */ decompress_fn decompress_method(const unsigned char *inbuf, int len, const char **name); diff --git a/lib/decompress_inflate.c b/lib/decompress_inflate.c index e36b296fc9f..bfe605ac534 100644 --- a/lib/decompress_inflate.c +++ b/lib/decompress_inflate.c @@ -25,7 +25,7 @@ #include #include -#define INBUF_LEN (16*1024) +#define GZIP_IOBUF_SIZE (16*1024) /* Included from initramfs et al code */ STATIC int INIT gunzip(unsigned char *buf, int len, @@ -55,7 +55,7 @@ STATIC int INIT gunzip(unsigned char *buf, int len, if (buf) zbuf = buf; else { - zbuf = malloc(INBUF_LEN); + zbuf = malloc(GZIP_IOBUF_SIZE); len = 0; } if (!zbuf) { @@ -77,7 +77,7 @@ STATIC int INIT gunzip(unsigned char *buf, int len, } if (len == 0) - len = fill(zbuf, INBUF_LEN); + len = fill(zbuf, GZIP_IOBUF_SIZE); /* verify the gzip header */ if (len < 10 || @@ -113,7 +113,7 @@ STATIC int INIT gunzip(unsigned char *buf, int len, while (rc == Z_OK) { if (strm->avail_in == 0) { /* TODO: handle case where both pos and fill are set */ - len = fill(zbuf, INBUF_LEN); + len = fill(zbuf, GZIP_IOBUF_SIZE); if (len < 0) { rc = -1; error("read error"); -- GitLab From b1af4315d823a2b6659c5b14bc17f7bc61878ef4 Mon Sep 17 00:00:00 2001 From: Phillip Lougher Date: Thu, 6 Aug 2009 15:09:31 -0700 Subject: [PATCH 0904/1342] bzip2/lzma: remove nasty uncompressed size hack in pre-boot environment decompress_bunzip2 and decompress_unlzma have a nasty hack that subtracts 4 from the input length if being called in the pre-boot environment. This is a nasty hack because it relies on the fact that flush = NULL only when called from the pre-boot environment (i.e. arch/x86/boot/compressed/misc.c). initramfs.c/do_mounts_rd.c pass in a flush buffer (flush != NULL). This hack prevents the decompressors from being used with flush = NULL by other callers unless knowledge of the hack is propagated to them. This patch removes the hack by making decompress (called only from the pre-boot environment) a wrapper function that subtracts 4 from the input length before calling the decompressor. Signed-off-by: Phillip Lougher Cc: "H. Peter Anvin" Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- lib/decompress_bunzip2.c | 22 ++++++++++++++++------ lib/decompress_unlzma.c | 21 ++++++++++++++++----- 2 files changed, 32 insertions(+), 11 deletions(-) diff --git a/lib/decompress_bunzip2.c b/lib/decompress_bunzip2.c index 708e2a86d87..d3dc9f2beb2 100644 --- a/lib/decompress_bunzip2.c +++ b/lib/decompress_bunzip2.c @@ -45,9 +45,11 @@ */ -#ifndef STATIC +#ifdef STATIC +#define PREBOOT +#else #include -#endif /* !STATIC */ +#endif /* STATIC */ #include #include @@ -681,9 +683,7 @@ STATIC int INIT bunzip2(unsigned char *buf, int len, set_error_fn(error_fn); if (flush) outbuf = malloc(BZIP2_IOBUF_SIZE); - else - len -= 4; /* Uncompressed size hack active in pre-boot - environment */ + if (!outbuf) { error("Could not allocate output bufer"); return -1; @@ -733,4 +733,14 @@ exit_0: return i; } -#define decompress bunzip2 +#ifdef PREBOOT +STATIC int INIT decompress(unsigned char *buf, int len, + int(*fill)(void*, unsigned int), + int(*flush)(void*, unsigned int), + unsigned char *outbuf, + int *pos, + void(*error_fn)(char *x)) +{ + return bunzip2(buf, len - 4, fill, flush, outbuf, pos, error_fn); +} +#endif diff --git a/lib/decompress_unlzma.c b/lib/decompress_unlzma.c index 32123a1340e..d3f9468e49d 100644 --- a/lib/decompress_unlzma.c +++ b/lib/decompress_unlzma.c @@ -29,7 +29,9 @@ *Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ -#ifndef STATIC +#ifdef STATIC +#define PREBOOT +#else #include #endif /* STATIC */ @@ -543,9 +545,7 @@ STATIC inline int INIT unlzma(unsigned char *buf, int in_len, int ret = -1; set_error_fn(error_fn); - if (!flush) - in_len -= 4; /* Uncompressed size hack active in pre-boot - environment */ + if (buf) inbuf = buf; else @@ -645,4 +645,15 @@ exit_0: return ret; } -#define decompress unlzma +#ifdef PREBOOT +STATIC int INIT decompress(unsigned char *buf, int in_len, + int(*fill)(void*, unsigned int), + int(*flush)(void*, unsigned int), + unsigned char *output, + int *posp, + void(*error_fn)(char *x) + ) +{ + return unlzma(buf, in_len - 4, fill, flush, output, posp, error_fn); +} +#endif -- GitLab From 9e5cf0ca2e9b65110ae5f094d7f0f7165cd1bbbb Mon Sep 17 00:00:00 2001 From: Albin Tonnerre Date: Thu, 6 Aug 2009 15:09:32 -0700 Subject: [PATCH 0905/1342] lib/decompress_*: only include if STATIC is not defined These includes were added by 079effb6933f34b9b1b67b08bd4fd7fb672d16ef ("kmemtrace, kbuild: fix slab.h dependency problem in lib/decompress_inflate.c") to fix the build when using kmemtrace. However this is not necessary when used to create a compressed kernel, and actually creates issues (brings a lot of things unavailable in the decompression environment), so don't include it if STATIC is defined. Signed-off-by: Albin Tonnerre Cc: Sam Ravnborg Cc: Russell King Cc: Ingo Molnar Cc: Thomas Gleixner Cc: "H. Peter Anvin" Cc: Pekka Enberg Cc: Eduard - Gabriel Munteanu Cc: Phillip Lougher Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- lib/decompress_bunzip2.c | 2 +- lib/decompress_inflate.c | 2 +- lib/decompress_unlzma.c | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) diff --git a/lib/decompress_bunzip2.c b/lib/decompress_bunzip2.c index d3dc9f2beb2..600f473a561 100644 --- a/lib/decompress_bunzip2.c +++ b/lib/decompress_bunzip2.c @@ -49,10 +49,10 @@ #define PREBOOT #else #include +#include #endif /* STATIC */ #include -#include #ifndef INT_MAX #define INT_MAX 0x7fffffff diff --git a/lib/decompress_inflate.c b/lib/decompress_inflate.c index bfe605ac534..68dfce59c1b 100644 --- a/lib/decompress_inflate.c +++ b/lib/decompress_inflate.c @@ -19,11 +19,11 @@ #include "zlib_inflate/inflate.h" #include "zlib_inflate/infutil.h" +#include #endif /* STATIC */ #include -#include #define GZIP_IOBUF_SIZE (16*1024) diff --git a/lib/decompress_unlzma.c b/lib/decompress_unlzma.c index d3f9468e49d..0b954e04bd3 100644 --- a/lib/decompress_unlzma.c +++ b/lib/decompress_unlzma.c @@ -33,10 +33,10 @@ #define PREBOOT #else #include +#include #endif /* STATIC */ #include -#include #define MIN(a, b) (((a) < (b)) ? (a) : (b)) -- GitLab From 3440625d78711bee41a84cf29c3d8c579b522666 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Thu, 6 Aug 2009 15:09:34 -0700 Subject: [PATCH 0906/1342] flat: fix uninitialized ptr with shared libs The new credentials code broke load_flat_shared_library() as it now uses an uninitialized cred pointer. Reported-by: Bernd Schmidt Tested-by: Bernd Schmidt Cc: Mike Frysinger Cc: David Howells Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- fs/binfmt_flat.c | 17 ++++++++++++----- 1 file changed, 12 insertions(+), 5 deletions(-) diff --git a/fs/binfmt_flat.c b/fs/binfmt_flat.c index 697f6b5f131..e92f229e3c6 100644 --- a/fs/binfmt_flat.c +++ b/fs/binfmt_flat.c @@ -828,15 +828,22 @@ static int load_flat_shared_library(int id, struct lib_info *libs) if (IS_ERR(bprm.file)) return res; + bprm.cred = prepare_exec_creds(); + res = -ENOMEM; + if (!bprm.cred) + goto out; + res = prepare_binprm(&bprm); if (res <= (unsigned long)-4096) res = load_flat_file(&bprm, libs, id, NULL); - if (bprm.file) { - allow_write_access(bprm.file); - fput(bprm.file); - bprm.file = NULL; - } + + abort_creds(bprm.cred); + +out: + allow_write_access(bprm.file); + fput(bprm.file); + return(res); } -- GitLab From 4baf8c9201e88546918cbfa61ea8062c38bc1644 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Fri, 7 Aug 2009 13:47:08 -0400 Subject: [PATCH 0907/1342] Btrfs: remove superfluous NULL pointer check in btrfs_rename() This takes care of the following entry from Dan's list: fs/btrfs/inode.c +4788 btrfs_rename(36) warning: variable derefenced before check 'old_inode' Reported-by: Dan Carpenter Cc: Jonathan Corbet Cc: Eugene Teo Cc: Julia Lawall Signed-off-by: Bartlomiej Zolnierkiewicz Signed-off-by: Chris Mason --- fs/btrfs/inode.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/fs/btrfs/inode.c b/fs/btrfs/inode.c index 3ea827ddf0f..04b53b5ebe5 100644 --- a/fs/btrfs/inode.c +++ b/fs/btrfs/inode.c @@ -4806,8 +4806,7 @@ static int btrfs_rename(struct inode *old_dir, struct dentry *old_dentry, * and the replacement file is large. Start IO on it now so * we don't add too much work to the end of the transaction */ - if (new_inode && old_inode && S_ISREG(old_inode->i_mode) && - new_inode->i_size && + if (new_inode && S_ISREG(old_inode->i_mode) && new_inode->i_size && old_inode->i_size > BTRFS_ORDERED_OPERATIONS_FLUSH_LIMIT) filemap_flush(old_inode->i_mapping); -- GitLab From 60f2e8f8a07331097a57ec4abcdc680405579377 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Fri, 7 Aug 2009 13:51:33 -0400 Subject: [PATCH 0908/1342] Btrfs: correct error-handling zlib error handling find_zlib_workspace returns an ERR_PTR value in an error case instead of NULL. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // @match exists@ expression x, E; statement S1, S2; @@ x = find_zlib_workspace(...) ... when != x = E ( * if (x == NULL || ...) S1 else S2 | * if (x == NULL && ...) S1 else S2 ) // Signed-off-by: Julia Lawall Signed-off-by: Chris Mason --- fs/btrfs/zlib.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/fs/btrfs/zlib.c b/fs/btrfs/zlib.c index ecfbce836d3..3e2b90eaa23 100644 --- a/fs/btrfs/zlib.c +++ b/fs/btrfs/zlib.c @@ -208,7 +208,7 @@ int btrfs_zlib_compress_pages(struct address_space *mapping, *total_in = 0; workspace = find_zlib_workspace(); - if (!workspace) + if (IS_ERR(workspace)) return -1; if (Z_OK != zlib_deflateInit(&workspace->def_strm, 3)) { @@ -366,7 +366,7 @@ int btrfs_zlib_decompress_biovec(struct page **pages_in, char *kaddr; workspace = find_zlib_workspace(); - if (!workspace) + if (IS_ERR(workspace)) return -ENOMEM; data_in = kmap(pages_in[page_in_index]); @@ -547,7 +547,7 @@ int btrfs_zlib_decompress(unsigned char *data_in, return -ENOMEM; workspace = find_zlib_workspace(); - if (!workspace) + if (IS_ERR(workspace)) return -ENOMEM; workspace->inf_strm.next_in = data_in; -- GitLab From ceab36edd3d3ad3ffd01d41d6d1e05ac1ff8357e Mon Sep 17 00:00:00 2001 From: Yan Zheng Date: Fri, 7 Aug 2009 13:51:33 -0400 Subject: [PATCH 0909/1342] Btrfs: fix balancing oops when invalidate_inode_pages2 returns EBUSY invalidate_inode_pages2_range may return -EBUSY occasionally which results Oops. This patch fixes the issue by moving invalidate_inode_pages2_range into a loop and keeping calling it until the return value is not -EBUSY. The EBUSY return is temporary, and can happen when the btrfs release page function is unable to release a page because the EXTENT_LOCK bit is set. Signed-off-by: Yan Zheng Signed-off-by: Chris Mason --- fs/btrfs/relocation.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) diff --git a/fs/btrfs/relocation.c b/fs/btrfs/relocation.c index e71264d1c2c..c04f7f21260 100644 --- a/fs/btrfs/relocation.c +++ b/fs/btrfs/relocation.c @@ -2553,8 +2553,13 @@ int relocate_inode_pages(struct inode *inode, u64 start, u64 len) last_index = (start + len - 1) >> PAGE_CACHE_SHIFT; /* make sure the dirty trick played by the caller work */ - ret = invalidate_inode_pages2_range(inode->i_mapping, - first_index, last_index); + while (1) { + ret = invalidate_inode_pages2_range(inode->i_mapping, + first_index, last_index); + if (ret != -EBUSY) + break; + schedule_timeout(HZ/10); + } if (ret) goto out_unlock; -- GitLab From e7432675f8ca868a4af365759a8d4c3779a3d922 Mon Sep 17 00:00:00 2001 From: Sunil Mushran Date: Thu, 6 Aug 2009 16:12:58 -0700 Subject: [PATCH 0910/1342] ocfs2: Initialize the cluster we're writing to in a non-sparse extend In a non-sparse extend, we correctly allocate (and zero) the clusters between the old_i_size and pos, but we don't zero the portions of the cluster we're writing to outside of pos<->len. It handles clustersize > pagesize and blocksize < pagesize. [Cleaned up by Joel Becker.] Signed-off-by: Sunil Mushran Signed-off-by: Joel Becker --- fs/ocfs2/aops.c | 66 +++++++++++++++++++++++++++++++++++-------------- 1 file changed, 47 insertions(+), 19 deletions(-) diff --git a/fs/ocfs2/aops.c b/fs/ocfs2/aops.c index e511df10145..b401654011a 100644 --- a/fs/ocfs2/aops.c +++ b/fs/ocfs2/aops.c @@ -895,18 +895,17 @@ struct ocfs2_write_cluster_desc { */ unsigned c_new; unsigned c_unwritten; + unsigned c_needs_zero; }; -static inline int ocfs2_should_zero_cluster(struct ocfs2_write_cluster_desc *d) -{ - return d->c_new || d->c_unwritten; -} - struct ocfs2_write_ctxt { /* Logical cluster position / len of write */ u32 w_cpos; u32 w_clen; + /* First cluster allocated in a nonsparse extend */ + u32 w_first_new_cpos; + struct ocfs2_write_cluster_desc w_desc[OCFS2_MAX_CLUSTERS_PER_PAGE]; /* @@ -984,6 +983,7 @@ static int ocfs2_alloc_write_ctxt(struct ocfs2_write_ctxt **wcp, return -ENOMEM; wc->w_cpos = pos >> osb->s_clustersize_bits; + wc->w_first_new_cpos = UINT_MAX; cend = (pos + len - 1) >> osb->s_clustersize_bits; wc->w_clen = cend - wc->w_cpos + 1; get_bh(di_bh); @@ -1218,20 +1218,18 @@ out: */ static int ocfs2_write_cluster(struct address_space *mapping, u32 phys, unsigned int unwritten, + unsigned int should_zero, struct ocfs2_alloc_context *data_ac, struct ocfs2_alloc_context *meta_ac, struct ocfs2_write_ctxt *wc, u32 cpos, loff_t user_pos, unsigned user_len) { - int ret, i, new, should_zero = 0; + int ret, i, new; u64 v_blkno, p_blkno; struct inode *inode = mapping->host; struct ocfs2_extent_tree et; new = phys == 0 ? 1 : 0; - if (new || unwritten) - should_zero = 1; - if (new) { u32 tmp_pos; @@ -1342,7 +1340,9 @@ static int ocfs2_write_cluster_by_desc(struct address_space *mapping, local_len = osb->s_clustersize - cluster_off; ret = ocfs2_write_cluster(mapping, desc->c_phys, - desc->c_unwritten, data_ac, meta_ac, + desc->c_unwritten, + desc->c_needs_zero, + data_ac, meta_ac, wc, desc->c_cpos, pos, local_len); if (ret) { mlog_errno(ret); @@ -1392,14 +1392,14 @@ static void ocfs2_set_target_boundaries(struct ocfs2_super *osb, * newly allocated cluster. */ desc = &wc->w_desc[0]; - if (ocfs2_should_zero_cluster(desc)) + if (desc->c_needs_zero) ocfs2_figure_cluster_boundaries(osb, desc->c_cpos, &wc->w_target_from, NULL); desc = &wc->w_desc[wc->w_clen - 1]; - if (ocfs2_should_zero_cluster(desc)) + if (desc->c_needs_zero) ocfs2_figure_cluster_boundaries(osb, desc->c_cpos, NULL, @@ -1467,13 +1467,28 @@ static int ocfs2_populate_write_desc(struct inode *inode, phys++; } + /* + * If w_first_new_cpos is < UINT_MAX, we have a non-sparse + * file that got extended. w_first_new_cpos tells us + * where the newly allocated clusters are so we can + * zero them. + */ + if (desc->c_cpos >= wc->w_first_new_cpos) { + BUG_ON(phys == 0); + desc->c_needs_zero = 1; + } + desc->c_phys = phys; if (phys == 0) { desc->c_new = 1; + desc->c_needs_zero = 1; *clusters_to_alloc = *clusters_to_alloc + 1; } - if (ext_flags & OCFS2_EXT_UNWRITTEN) + + if (ext_flags & OCFS2_EXT_UNWRITTEN) { desc->c_unwritten = 1; + desc->c_needs_zero = 1; + } num_clusters--; } @@ -1633,10 +1648,13 @@ static int ocfs2_expand_nonsparse_inode(struct inode *inode, loff_t pos, if (newsize <= i_size_read(inode)) return 0; - ret = ocfs2_extend_no_holes(inode, newsize, newsize - len); + ret = ocfs2_extend_no_holes(inode, newsize, pos); if (ret) mlog_errno(ret); + wc->w_first_new_cpos = + ocfs2_clusters_for_bytes(inode->i_sb, i_size_read(inode)); + return ret; } @@ -1645,7 +1663,7 @@ int ocfs2_write_begin_nolock(struct address_space *mapping, struct page **pagep, void **fsdata, struct buffer_head *di_bh, struct page *mmap_page) { - int ret, credits = OCFS2_INODE_UPDATE_CREDITS; + int ret, cluster_of_pages, credits = OCFS2_INODE_UPDATE_CREDITS; unsigned int clusters_to_alloc, extents_to_split; struct ocfs2_write_ctxt *wc; struct inode *inode = mapping->host; @@ -1723,8 +1741,19 @@ int ocfs2_write_begin_nolock(struct address_space *mapping, } - ocfs2_set_target_boundaries(osb, wc, pos, len, - clusters_to_alloc + extents_to_split); + /* + * We have to zero sparse allocated clusters, unwritten extent clusters, + * and non-sparse clusters we just extended. For non-sparse writes, + * we know zeros will only be needed in the first and/or last cluster. + */ + if (clusters_to_alloc || extents_to_split || + wc->w_desc[0].c_needs_zero || + wc->w_desc[wc->w_clen - 1].c_needs_zero) + cluster_of_pages = 1; + else + cluster_of_pages = 0; + + ocfs2_set_target_boundaries(osb, wc, pos, len, cluster_of_pages); handle = ocfs2_start_trans(osb, credits); if (IS_ERR(handle)) { @@ -1757,8 +1786,7 @@ int ocfs2_write_begin_nolock(struct address_space *mapping, * extent. */ ret = ocfs2_grab_pages_for_write(mapping, wc, wc->w_cpos, pos, - clusters_to_alloc + extents_to_split, - mmap_page); + cluster_of_pages, mmap_page); if (ret) { mlog_errno(ret); goto out_quota; -- GitLab From 8a57a9dda760ea7845390f1cd36f3eb2a49391d8 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Thu, 6 Aug 2009 16:07:50 -0700 Subject: [PATCH 0911/1342] ocfs2: keep index within status_map[] Do not exceed array status_map[] Signed-off-by: Roel Kluin Cc: Mark Fasheh Signed-off-by: Andrew Morton Signed-off-by: Joel Becker --- fs/ocfs2/stack_o2cb.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/fs/ocfs2/stack_o2cb.c b/fs/ocfs2/stack_o2cb.c index 3f661376a2d..e49c4105026 100644 --- a/fs/ocfs2/stack_o2cb.c +++ b/fs/ocfs2/stack_o2cb.c @@ -17,6 +17,7 @@ * General Public License for more details. */ +#include #include #include @@ -153,7 +154,7 @@ static int status_map[] = { static int dlm_status_to_errno(enum dlm_status status) { - BUG_ON(status > (sizeof(status_map) / sizeof(status_map[0]))); + BUG_ON(status < 0 || status >= ARRAY_SIZE(status_map)); return status_map[status]; } -- GitLab From 49276560c9004fce24c42e3c0ad75f34d956fc63 Mon Sep 17 00:00:00 2001 From: Khanh-Dang Nguyen Thu Lam Date: Tue, 28 Jul 2009 19:41:17 +0200 Subject: [PATCH 0912/1342] USB: pl2303: New vendor and product id I am submitting a patch for the pl2303 driver. This patch adds support for the "Sony QN-3USB" cable (vendor=0x054c, product=0x0437). This USB cable is a so-called data cable used to connect a Sony mobile phone to a computer. Supported models are Sony CMD-J5, J6, J7, J16, J26, J70 and Z7. I have used this patch with my Sony CMD-J70 for several days and I haven't encountered any kernel/hardware issue. From: Khanh-Dang Nguyen Thu Lam Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/pl2303.c | 1 + drivers/usb/serial/pl2303.h | 4 ++++ 2 files changed, 5 insertions(+) diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c index 7d15bfa7c2d..3e86815b270 100644 --- a/drivers/usb/serial/pl2303.c +++ b/drivers/usb/serial/pl2303.c @@ -95,6 +95,7 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(SUPERIAL_VENDOR_ID, SUPERIAL_PRODUCT_ID) }, { USB_DEVICE(HP_VENDOR_ID, HP_LD220_PRODUCT_ID) }, { USB_DEVICE(CRESSI_VENDOR_ID, CRESSI_EDY_PRODUCT_ID) }, + { USB_DEVICE(SONY_VENDOR_ID, SONY_QN3USB_PRODUCT_ID) }, { } /* Terminating entry */ }; diff --git a/drivers/usb/serial/pl2303.h b/drivers/usb/serial/pl2303.h index 12aac7d2462..ee9505e1dd9 100644 --- a/drivers/usb/serial/pl2303.h +++ b/drivers/usb/serial/pl2303.h @@ -126,3 +126,7 @@ /* Cressi Edy (diving computer) PC interface */ #define CRESSI_VENDOR_ID 0x04b8 #define CRESSI_EDY_PRODUCT_ID 0x0521 + +/* Sony, USB data cable for CMD-Jxx mobile phones */ +#define SONY_VENDOR_ID 0x054c +#define SONY_QN3USB_PRODUCT_ID 0x0437 -- GitLab From 18753ebc8a98efe0e8ff6167afb31cef220c8e50 Mon Sep 17 00:00:00 2001 From: Michael Buesch Date: Wed, 29 Jul 2009 11:39:03 +0200 Subject: [PATCH 0913/1342] USB: devio: Properly do access_ok() checks access_ok() checks must be done on every part of the userspace structure that is accessed. If access_ok() on one part of the struct succeeded, it does not imply it will succeed on other parts of the struct. (Does depend on the architecture implementation of access_ok()). This changes the __get_user() users to first check access_ok() on the data structure. Signed-off-by: Michael Buesch Cc: stable Cc: Pete Zaitcev Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/devio.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c index 38b8bce782d..e192fa05f8a 100644 --- a/drivers/usb/core/devio.c +++ b/drivers/usb/core/devio.c @@ -1321,7 +1321,8 @@ static int get_urb32(struct usbdevfs_urb *kurb, struct usbdevfs_urb32 __user *uurb) { __u32 uptr; - if (get_user(kurb->type, &uurb->type) || + if (!access_ok(VERIFY_READ, uurb, sizeof(*uurb)) || + __get_user(kurb->type, &uurb->type) || __get_user(kurb->endpoint, &uurb->endpoint) || __get_user(kurb->status, &uurb->status) || __get_user(kurb->flags, &uurb->flags) || @@ -1536,8 +1537,9 @@ static int proc_ioctl_compat(struct dev_state *ps, compat_uptr_t arg) u32 udata; uioc = compat_ptr((long)arg); - if (get_user(ctrl.ifno, &uioc->ifno) || - get_user(ctrl.ioctl_code, &uioc->ioctl_code) || + if (!access_ok(VERIFY_READ, uioc, sizeof(*uioc)) || + __get_user(ctrl.ifno, &uioc->ifno) || + __get_user(ctrl.ioctl_code, &uioc->ioctl_code) || __get_user(udata, &uioc->data)) return -EFAULT; ctrl.data = compat_ptr(udata); -- GitLab From e8e2ff462dd92693f29eb848f42d3eb720390d59 Mon Sep 17 00:00:00 2001 From: "Gupta, Ajay Kumar" Date: Wed, 29 Jul 2009 11:58:57 +0530 Subject: [PATCH 0914/1342] USB: musb: fix the nop registration for OMAP3EVM OMAP3EVM uses ISP1504 phy which doesn't require any programming and thus has to use NOP otg transceiver. Cleanups being done: - Remove unwanted code in usb-musb.c file - Register NOP in OMAP3EVM board file using usb_nop_xceiv_register(). - Select NOP_USB_XCEIV for OMAP3EVM boards. - Don't enable TWL4030_USB in omap3_evm_defconfig Signed-off-by: Ajay Kumar Gupta Signed-off-by: Eino-Ville Talvala Acked-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- arch/arm/configs/omap3_evm_defconfig | 2 +- arch/arm/mach-omap2/board-omap3evm.c | 5 +++++ arch/arm/mach-omap2/usb-musb.c | 21 --------------------- drivers/usb/musb/Kconfig | 1 + 4 files changed, 7 insertions(+), 22 deletions(-) diff --git a/arch/arm/configs/omap3_evm_defconfig b/arch/arm/configs/omap3_evm_defconfig index 28be17fbc15..d5ff4776cd0 100644 --- a/arch/arm/configs/omap3_evm_defconfig +++ b/arch/arm/configs/omap3_evm_defconfig @@ -1107,7 +1107,7 @@ CONFIG_USB_ZERO=m CONFIG_USB_OTG_UTILS=y # CONFIG_USB_GPIO_VBUS is not set # CONFIG_ISP1301_OMAP is not set -CONFIG_TWL4030_USB=y +# CONFIG_TWL4030_USB is not set # CONFIG_NOP_USB_XCEIV is not set CONFIG_MMC=y # CONFIG_MMC_DEBUG is not set diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index d3cc145814d..cf3dd771a67 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -25,6 +25,7 @@ #include #include #include +#include #include #include @@ -307,6 +308,10 @@ static void __init omap3_evm_init(void) ARRAY_SIZE(omap3evm_spi_board_info)); omap_serial_init(); +#ifdef CONFIG_NOP_USB_XCEIV + /* OMAP3EVM uses ISP1504 phy and so register nop transceiver */ + usb_nop_xceiv_register(); +#endif usb_musb_init(); ads7846_dev_init(); } diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c index d85296dc896..739e59e8025 100644 --- a/arch/arm/mach-omap2/usb-musb.c +++ b/arch/arm/mach-omap2/usb-musb.c @@ -155,20 +155,6 @@ static struct platform_device musb_device = { .resource = musb_resources, }; -#ifdef CONFIG_NOP_USB_XCEIV -static u64 nop_xceiv_dmamask = DMA_BIT_MASK(32); - -static struct platform_device nop_xceiv_device = { - .name = "nop_usb_xceiv", - .id = -1, - .dev = { - .dma_mask = &nop_xceiv_dmamask, - .coherent_dma_mask = DMA_BIT_MASK(32), - .platform_data = NULL, - }, -}; -#endif - void __init usb_musb_init(void) { if (cpu_is_omap243x()) @@ -183,13 +169,6 @@ void __init usb_musb_init(void) */ musb_plat.clock = "ick"; -#ifdef CONFIG_NOP_USB_XCEIV - if (platform_device_register(&nop_xceiv_device) < 0) { - printk(KERN_ERR "Unable to register NOP-XCEIV device\n"); - return; - } -#endif - if (platform_device_register(&musb_device) < 0) { printk(KERN_ERR "Unable to register HS-USB (MUSB) device\n"); return; diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig index 70073b157f0..803adcb5ac1 100644 --- a/drivers/usb/musb/Kconfig +++ b/drivers/usb/musb/Kconfig @@ -12,6 +12,7 @@ config USB_MUSB_HDRC depends on !SUPERH select NOP_USB_XCEIV if ARCH_DAVINCI select TWL4030_USB if MACH_OMAP_3430SDP + select NOP_USB_XCEIV if MACH_OMAP3EVM select USB_OTG_UTILS tristate 'Inventra Highspeed Dual Role Controller (TI, ADI, ...)' help -- GitLab From 01105a246345f011fde64d24a601090b646e9e4c Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Thu, 30 Jul 2009 15:28:14 -0400 Subject: [PATCH 0915/1342] USB: usbfs: fix -ENOENT error code to be -ENODEV This patch (as1272) changes the error code returned when an open call for a USB device node fails to locate the corresponding device. The appropriate error code is -ENODEV, not -ENOENT. Signed-off-by: Alan Stern CC: Kay Sievers Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/devio.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c index e192fa05f8a..4247eccf858 100644 --- a/drivers/usb/core/devio.c +++ b/drivers/usb/core/devio.c @@ -595,7 +595,7 @@ static int usbdev_open(struct inode *inode, struct file *file) if (!ps) goto out; - ret = -ENOENT; + ret = -ENODEV; /* usbdev device-node */ if (imajor(inode) == USB_DEVICE_MAJOR) -- GitLab From 7a0f0d951273eee889c2441846842348ebc00a2a Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Fri, 31 Jul 2009 10:40:22 -0400 Subject: [PATCH 0916/1342] USB: EHCI: fix two new bugs related to Clear-TT-Buffer This patch (as1273) fixes two(!) bugs introduced by the new Clear-TT-Buffer implementation in ehci-hcd. It is now possible for an idle QH to have some URBs on its queue -- this will happen if a Clear-TT-Buffer is pending for the QH's endpoint. Consequently we should not issue a warning when someone tries to unlink an URB from an idle QH; instead we should process the request immediately. The refcounts for QHs could get messed up, because submit_async() would increment the refcount when calling qh_link_async() and qh_link_async() would then refuse to link the QH into the schedule if a Clear-TT-Buffer was pending. Instead we should increment the refcount only when the QH actually is added to the schedule. The current code tries to be clever by leaving the refcount alone if an unlink is immediately followed by a relink; the patch changes this to an unconditional decrement and increment (although they occur in the opposite order). Signed-off-by: Alan Stern CC: David Brownell Tested-by: Manuel Lauss Tested-by: Matthijs Kooijman Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-hcd.c | 3 ++- drivers/usb/host/ehci-q.c | 6 +++--- 2 files changed, 5 insertions(+), 4 deletions(-) diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c index 7d03549c333..11c627ce602 100644 --- a/drivers/usb/host/ehci-hcd.c +++ b/drivers/usb/host/ehci-hcd.c @@ -903,7 +903,8 @@ static int ehci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status) /* already started */ break; case QH_STATE_IDLE: - WARN_ON(1); + /* QH might be waiting for a Clear-TT-Buffer */ + qh_completions(ehci, qh); break; } break; diff --git a/drivers/usb/host/ehci-q.c b/drivers/usb/host/ehci-q.c index 9a1384747f3..b2738050557 100644 --- a/drivers/usb/host/ehci-q.c +++ b/drivers/usb/host/ehci-q.c @@ -940,6 +940,7 @@ static void qh_link_async (struct ehci_hcd *ehci, struct ehci_qh *qh) head->qh_next.qh = qh; head->hw_next = dma; + qh_get(qh); qh->xacterrs = QH_XACTERR_MAX; qh->qh_state = QH_STATE_LINKED; /* qtd completions reported later by interrupt */ @@ -1080,7 +1081,7 @@ submit_async ( * the HC and TT handle it when the TT has a buffer ready. */ if (likely (qh->qh_state == QH_STATE_IDLE)) - qh_link_async (ehci, qh_get (qh)); + qh_link_async(ehci, qh); done: spin_unlock_irqrestore (&ehci->lock, flags); if (unlikely (qh == NULL)) @@ -1115,8 +1116,6 @@ static void end_unlink_async (struct ehci_hcd *ehci) && HC_IS_RUNNING (ehci_to_hcd(ehci)->state)) qh_link_async (ehci, qh); else { - qh_put (qh); // refcount from async list - /* it's not free to turn the async schedule on/off; leave it * active but idle for a while once it empties. */ @@ -1124,6 +1123,7 @@ static void end_unlink_async (struct ehci_hcd *ehci) && ehci->async->qh_next.qh == NULL) timer_action (ehci, TIMER_ASYNC_OFF); } + qh_put(qh); /* refcount from async list */ if (next) { ehci->reclaim = NULL; -- GitLab From ef4638f955f2c4a667c8af20769d03f5ed3781ca Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Fri, 31 Jul 2009 10:41:40 -0400 Subject: [PATCH 0917/1342] USB: EHCI: fix counting of transaction error retries This patch (as1274) simplifies the counting of transaction-error retries. Now we will count up from 0 to QH_XACTERR_MAX instead of down from QH_XACTERR_MAX to 0. The patch also fixes a small bug: qh->xacterr was not getting initialized for interrupt endpoints. Signed-off-by: Alan Stern Tested-by: Matthijs Kooijman Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-q.c | 9 ++++----- drivers/usb/host/ehci-sched.c | 1 + 2 files changed, 5 insertions(+), 5 deletions(-) diff --git a/drivers/usb/host/ehci-q.c b/drivers/usb/host/ehci-q.c index b2738050557..7673554fa64 100644 --- a/drivers/usb/host/ehci-q.c +++ b/drivers/usb/host/ehci-q.c @@ -375,12 +375,11 @@ qh_completions (struct ehci_hcd *ehci, struct ehci_qh *qh) */ if ((token & QTD_STS_XACT) && QTD_CERR(token) == 0 && - --qh->xacterrs > 0 && + ++qh->xacterrs < QH_XACTERR_MAX && !urb->unlinked) { ehci_dbg(ehci, "detected XactErr len %zu/%zu retry %d\n", - qtd->length - QTD_LENGTH(token), qtd->length, - QH_XACTERR_MAX - qh->xacterrs); + qtd->length - QTD_LENGTH(token), qtd->length, qh->xacterrs); /* reset the token in the qtd and the * qh overlay (which still contains @@ -494,7 +493,7 @@ halt: last = qtd; /* reinit the xacterr counter for the next qtd */ - qh->xacterrs = QH_XACTERR_MAX; + qh->xacterrs = 0; } /* last urb's completion might still need calling */ @@ -941,7 +940,7 @@ static void qh_link_async (struct ehci_hcd *ehci, struct ehci_qh *qh) head->hw_next = dma; qh_get(qh); - qh->xacterrs = QH_XACTERR_MAX; + qh->xacterrs = 0; qh->qh_state = QH_STATE_LINKED; /* qtd completions reported later by interrupt */ } diff --git a/drivers/usb/host/ehci-sched.c b/drivers/usb/host/ehci-sched.c index 74f7f83b29a..edd61ee9032 100644 --- a/drivers/usb/host/ehci-sched.c +++ b/drivers/usb/host/ehci-sched.c @@ -542,6 +542,7 @@ static int qh_link_periodic (struct ehci_hcd *ehci, struct ehci_qh *qh) } } qh->qh_state = QH_STATE_LINKED; + qh->xacterrs = 0; qh_get (qh); /* update per-qh bandwidth for usbfs */ -- GitLab From c47aacc67a3d26dfab9c9b8965975ed2b2010b30 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Marko=20H=C3=A4nninen?= Date: Fri, 31 Jul 2009 22:32:39 +0300 Subject: [PATCH 0918/1342] USB: ftdi_sio: add vendor and product id for Bayer glucose meter serial converter cable MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Attached patch adds USB vendor and product IDs for Bayer's USB to serial converter cable used by Bayer blood glucose meters. It seems to be a FT232RL based device and works without any problem with ftdi_sio driver when this patch is applied. See: http://winglucofacts.com/cables/ Signed-off-by: Marko Hänninen Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 1 + drivers/usb/serial/ftdi_sio.h | 7 +++++++ 2 files changed, 8 insertions(+) diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index b574878c78b..500087ea58a 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -699,6 +699,7 @@ static struct usb_device_id id_table_combined [] = { .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(LARSENBRUSGAARD_VID, LB_ALTITRACK_PID) }, { USB_DEVICE(GN_OTOMETRICS_VID, AURICAL_USB_PID) }, + { USB_DEVICE(BAYER_VID, BAYER_CONTOUR_CABLE_PID) }, { }, /* Optional parameter entry */ { } /* Terminating entry */ }; diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h index 24dbd99e87d..f203b2a5130 100644 --- a/drivers/usb/serial/ftdi_sio.h +++ b/drivers/usb/serial/ftdi_sio.h @@ -953,6 +953,13 @@ #define GN_OTOMETRICS_VID 0x0c33 /* Vendor ID */ #define AURICAL_USB_PID 0x0010 /* Aurical USB Audiometer */ +/* + * Bayer Ascensia Contour blood glucose meter USB-converter cable. + * http://winglucofacts.com/cables/ + */ +#define BAYER_VID 0x1A79 +#define BAYER_CONTOUR_CABLE_PID 0x6001 + /* * BmRequestType: 1100 0000b * bRequest: FTDI_E2_READ -- GitLab From 50d0678e2026c18e4147f0b16b5853113659b82d Mon Sep 17 00:00:00 2001 From: Dhaval Vasa Date: Fri, 7 Aug 2009 17:26:49 +0530 Subject: [PATCH 0919/1342] USB: ftdi_sio: add product_id for Marvell OpenRD Base, Client reference: http://www.open-rd.org Signed-off-by: Dhaval Vasa Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 2 ++ drivers/usb/serial/ftdi_sio.h | 7 +++++++ 2 files changed, 9 insertions(+) diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 500087ea58a..8fec5d4455c 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -700,6 +700,8 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(LARSENBRUSGAARD_VID, LB_ALTITRACK_PID) }, { USB_DEVICE(GN_OTOMETRICS_VID, AURICAL_USB_PID) }, { USB_DEVICE(BAYER_VID, BAYER_CONTOUR_CABLE_PID) }, + { USB_DEVICE(FTDI_VID, MARVELL_OPENRD_PID), + .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { }, /* Optional parameter entry */ { } /* Terminating entry */ }; diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h index f203b2a5130..8c92b88166a 100644 --- a/drivers/usb/serial/ftdi_sio.h +++ b/drivers/usb/serial/ftdi_sio.h @@ -960,6 +960,13 @@ #define BAYER_VID 0x1A79 #define BAYER_CONTOUR_CABLE_PID 0x6001 +/* + * Marvell OpenRD Base, Client + * http://www.open-rd.org + * OpenRD Base, Client use VID 0x0403 + */ +#define MARVELL_OPENRD_PID 0x9e90 + /* * BmRequestType: 1100 0000b * bRequest: FTDI_E2_READ -- GitLab From c15e3ca1d822abba78c00b1ffc3e7b382a50396e Mon Sep 17 00:00:00 2001 From: Rogerio Brito Date: Thu, 6 Aug 2009 15:20:19 -0700 Subject: [PATCH 0920/1342] USB: storage: include Prolific Technology USB drive in unusual_devs list Add a quirk entry for the Leading Driver UD-11 usb flash drive. As Alan Stern told me, the device doesn't deal correctly with the locking media feature of the device, and this patch incorporates it. Compiled, tested, working. Signed-off-by: Rogerio Brito Cc: Phil Dibowitz Cc: Alan Stern Cc: Robert Hancock Cc: stable Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/unusual_devs.h | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h index 1b9c5dd0fb2..7477d411959 100644 --- a/drivers/usb/storage/unusual_devs.h +++ b/drivers/usb/storage/unusual_devs.h @@ -838,6 +838,13 @@ UNUSUAL_DEV( 0x066f, 0x8000, 0x0001, 0x0001, US_SC_DEVICE, US_PR_DEVICE, NULL, US_FL_FIX_CAPACITY ), +/* Reported by Rogerio Brito */ +UNUSUAL_DEV( 0x067b, 0x2317, 0x0001, 0x001, + "Prolific Technology, Inc.", + "Mass Storage Device", + US_SC_DEVICE, US_PR_DEVICE, NULL, + US_FL_NOT_LOCKABLE ), + /* Reported by Richard -=[]=- */ /* Change to bcdDeviceMin (0x0100 to 0x0001) reported by * Thomas Bartosik */ -- GitLab From cf7fdd57f978d40ceb9a0f58a25f5cf9c84d6f33 Mon Sep 17 00:00:00 2001 From: Oliver Neukum Date: Tue, 4 Aug 2009 23:52:09 +0200 Subject: [PATCH 0921/1342] USB: fix oops on disconnect in cdc-acm This patch fixes an oops caused when during an unplug a device's table of endpoints is zeroed before the driver is notified. A pointer to the endpoint must be cached. this fixes a regression caused by commit 5186ffee2320942c3dc9745f7930e0eb15329ca6 Therefore it should go into 2.6.31 Signed-off-by: Oliver Neukum Signed-off-by: Greg Kroah-Hartman --- drivers/usb/class/cdc-acm.c | 10 +++++----- drivers/usb/class/cdc-acm.h | 2 ++ 2 files changed, 7 insertions(+), 5 deletions(-) diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index e1f89416ef8..2bfc41ece0e 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -387,7 +387,6 @@ static void acm_rx_tasklet(unsigned long _acm) struct acm_ru *rcv; unsigned long flags; unsigned char throttled; - struct usb_host_endpoint *ep; dbg("Entering acm_rx_tasklet"); @@ -463,14 +462,12 @@ urbs: rcv->buffer = buf; - ep = (usb_pipein(acm->rx_endpoint) ? acm->dev->ep_in : acm->dev->ep_out) - [usb_pipeendpoint(acm->rx_endpoint)]; - if (usb_endpoint_xfer_int(&ep->desc)) + if (acm->is_int_ep) usb_fill_int_urb(rcv->urb, acm->dev, acm->rx_endpoint, buf->base, acm->readsize, - acm_read_bulk, rcv, ep->desc.bInterval); + acm_read_bulk, rcv, acm->bInterval); else usb_fill_bulk_urb(rcv->urb, acm->dev, acm->rx_endpoint, @@ -1183,6 +1180,9 @@ made_compressed_probe: spin_lock_init(&acm->read_lock); mutex_init(&acm->mutex); acm->rx_endpoint = usb_rcvbulkpipe(usb_dev, epread->bEndpointAddress); + acm->is_int_ep = usb_endpoint_xfer_int(epread); + if (acm->is_int_ep) + acm->bInterval = epread->bInterval; tty_port_init(&acm->port); acm->port.ops = &acm_port_ops; diff --git a/drivers/usb/class/cdc-acm.h b/drivers/usb/class/cdc-acm.h index 1602324808b..c4a0ee8ffcc 100644 --- a/drivers/usb/class/cdc-acm.h +++ b/drivers/usb/class/cdc-acm.h @@ -126,6 +126,8 @@ struct acm { unsigned int ctrl_caps; /* control capabilities from the class specific header */ unsigned int susp_count; /* number of suspended interfaces */ int combined_interfaces:1; /* control and data collapsed */ + int is_int_ep:1; /* interrupt endpoints contrary to spec used */ + u8 bInterval; struct acm_wb *delayed_wb; /* write queued for a device about to be woken */ }; -- GitLab From 4d2da07bc876fc5bc455e0721df388a3db7e4ba5 Mon Sep 17 00:00:00 2001 From: Jakob Gruber Date: Thu, 30 Jul 2009 20:37:36 +0200 Subject: [PATCH 0922/1342] Staging: rt2870: Add USB ID for Linksys, Planex Communications, Belkin Linksys WUSB100, Belkin F5D8053 N, Planex Communications unknown model. Signed-off-by: Jakob Gruber Signed-off-by: Greg Kroah-Hartman --- drivers/staging/rt2870/rt2870.h | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/staging/rt2870/rt2870.h b/drivers/staging/rt2870/rt2870.h index 29e3b53e52a..10e1640d61e 100644 --- a/drivers/staging/rt2870/rt2870.h +++ b/drivers/staging/rt2870/rt2870.h @@ -79,6 +79,7 @@ { \ {USB_DEVICE(0x148F,0x2770)}, /* Ralink */ \ {USB_DEVICE(0x1737,0x0071)}, /* Linksys WUSB600N */ \ + {USB_DEVICE(0x1737,0x0070)}, /* Linksys */ \ {USB_DEVICE(0x148F,0x2870)}, /* Ralink */ \ {USB_DEVICE(0x148F,0x3070)}, /* Ralink */ \ {USB_DEVICE(0x0B05,0x1731)}, /* Asus */ \ @@ -93,12 +94,14 @@ {USB_DEVICE(0x14B2,0x3C06)}, /* Conceptronic */ \ {USB_DEVICE(0x14B2,0x3C28)}, /* Conceptronic */ \ {USB_DEVICE(0x2019,0xED06)}, /* Planex Communications, Inc. */ \ + {USB_DEVICE(0x2019,0xED14)}, /* Planex Communications, Inc. */ \ {USB_DEVICE(0x2019,0xAB25)}, /* Planex Communications, Inc. RT3070 */ \ {USB_DEVICE(0x07D1,0x3C09)}, /* D-Link */ \ {USB_DEVICE(0x07D1,0x3C11)}, /* D-Link */ \ {USB_DEVICE(0x14B2,0x3C07)}, /* AL */ \ {USB_DEVICE(0x14B2,0x3C12)}, /* AL */ \ {USB_DEVICE(0x050D,0x8053)}, /* Belkin */ \ + {USB_DEVICE(0x050D,0x815C)}, /* Belkin */ \ {USB_DEVICE(0x14B2,0x3C23)}, /* Airlink */ \ {USB_DEVICE(0x14B2,0x3C27)}, /* Airlink */ \ {USB_DEVICE(0x07AA,0x002F)}, /* Corega */ \ -- GitLab From 2c63abf9e8a51dec886da482dfd8ae752581a61c Mon Sep 17 00:00:00 2001 From: Mike Galbraith Date: Fri, 31 Jul 2009 07:14:04 +0200 Subject: [PATCH 0923/1342] Staging: rt2870: Revert d44ca7 Removal of kernel_thread() API Staging: rt2870: Revert d44ca7 Removal of kernel_thread() API The sanity check this patch introduced triggers on shutdown, apparently due to threads having already exited by the time BUG_ON() is reached. Signed-off-by: Mike Galbraith Cc: Peter Teoh Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/staging/rt2860/rt_linux.h | 13 ++-- drivers/staging/rt2870/2870_main_dev.c | 67 +++++++++++++------ .../staging/rt2870/common/2870_rtmp_init.c | 33 +++++---- drivers/staging/rt2870/common/rtusb_io.c | 3 +- drivers/staging/rt2870/rt2870.h | 6 +- 5 files changed, 68 insertions(+), 54 deletions(-) diff --git a/drivers/staging/rt2860/rt_linux.h b/drivers/staging/rt2860/rt_linux.h index 85175c18243..25b53ac3f82 100644 --- a/drivers/staging/rt2860/rt_linux.h +++ b/drivers/staging/rt2860/rt_linux.h @@ -43,9 +43,6 @@ #include "rtmp_type.h" #include #include -#if !defined(RT2860) && !defined(RT30xx) -#include -#endif #include #include @@ -166,9 +163,7 @@ typedef int (*HARD_START_XMIT_FUNC)(struct sk_buff *skb, struct net_device *net_ #ifndef RT30xx typedef struct pid * THREAD_PID; -#ifdef RT2860 #define THREAD_PID_INIT_VALUE NULL -#endif #define GET_PID(_v) find_get_pid(_v) #define GET_PID_NUMBER(_v) pid_nr(_v) #define CHECK_PID_LEGALITY(_pid) if (pid_nr(_pid) >= 0) @@ -188,12 +183,12 @@ struct os_cookie { dma_addr_t pAd_pa; #endif #ifdef RT2870 - struct usb_device *pUsb_Dev; + struct usb_device *pUsb_Dev; #ifndef RT30xx - struct task_struct *MLMEThr_task; - struct task_struct *RTUSBCmdThr_task; - struct task_struct *TimerQThr_task; + THREAD_PID MLMEThr_pid; + THREAD_PID RTUSBCmdThr_pid; + THREAD_PID TimerQThr_pid; #endif #ifdef RT30xx struct pid *MLMEThr_pid; diff --git a/drivers/staging/rt2870/2870_main_dev.c b/drivers/staging/rt2870/2870_main_dev.c index dd01c64fbf6..a4e8696ca39 100644 --- a/drivers/staging/rt2870/2870_main_dev.c +++ b/drivers/staging/rt2870/2870_main_dev.c @@ -235,7 +235,7 @@ INT MlmeThread( DBGPRINT(RT_DEBUG_TRACE,( "<---%s\n",__func__)); #ifndef RT30xx - pObj->MLMEThr_task = NULL; + pObj->MLMEThr_pid = THREAD_PID_INIT_VALUE; #endif #ifdef RT30xx pObj->MLMEThr_pid = NULL; @@ -348,7 +348,7 @@ INT RTUSBCmdThread( DBGPRINT(RT_DEBUG_TRACE,( "<---RTUSBCmdThread\n")); #ifndef RT30xx - pObj->RTUSBCmdThr_task = NULL; + pObj->RTUSBCmdThr_pid = THREAD_PID_INIT_VALUE; #endif #ifdef RT30xx pObj->RTUSBCmdThr_pid = NULL; @@ -447,7 +447,7 @@ INT TimerQThread( DBGPRINT(RT_DEBUG_TRACE,( "<---%s\n",__func__)); #ifndef RT30xx - pObj->TimerQThr_task = NULL; + pObj->TimerQThr_pid = THREAD_PID_INIT_VALUE; #endif #ifdef RT30xx pObj->TimerQThr_pid = NULL; @@ -883,46 +883,69 @@ VOID RT28xxThreadTerminate( // Terminate Threads #ifndef RT30xx - BUG_ON(pObj->TimerQThr_task == NULL); - CHECK_PID_LEGALITY(task_pid(pObj->TimerQThr_task)) + CHECK_PID_LEGALITY(pObj->TimerQThr_pid) { POS_COOKIE pObj = (POS_COOKIE)pAd->OS_Cookie; - printk(KERN_DEBUG "Terminate the TimerQThr pid=%d!\n", - pid_nr(task_pid(pObj->TimerQThr_task))); + printk("Terminate the TimerQThr_pid=%d!\n", GET_PID_NUMBER(pObj->TimerQThr_pid)); mb(); pAd->TimerFunc_kill = 1; mb(); - kthread_stop(pObj->TimerQThr_task); - pObj->TimerQThr_task = NULL; + ret = KILL_THREAD_PID(pObj->TimerQThr_pid, SIGTERM, 1); + if (ret) + { + printk(KERN_WARNING "%s: unable to stop TimerQThread, pid=%d, ret=%d!\n", + pAd->net_dev->name, GET_PID_NUMBER(pObj->TimerQThr_pid), ret); + } + else + { + wait_for_completion(&pAd->TimerQComplete); + pObj->TimerQThr_pid = THREAD_PID_INIT_VALUE; + } } - BUG_ON(pObj->MLMEThr_task == NULL); - CHECK_PID_LEGALITY(task_pid(pObj->MLMEThr_task)) + CHECK_PID_LEGALITY(pObj->MLMEThr_pid) { - printk(KERN_DEBUG "Terminate the MLMEThr pid=%d!\n", - pid_nr(task_pid(pObj->MLMEThr_task))); + printk("Terminate the MLMEThr_pid=%d!\n", GET_PID_NUMBER(pObj->MLMEThr_pid)); mb(); pAd->mlme_kill = 1; //RT28XX_MLME_HANDLER(pAd); mb(); - kthread_stop(pObj->MLMEThr_task); - pObj->MLMEThr_task = NULL; + ret = KILL_THREAD_PID(pObj->MLMEThr_pid, SIGTERM, 1); + if (ret) + { + printk (KERN_WARNING "%s: unable to Mlme thread, pid=%d, ret=%d!\n", + pAd->net_dev->name, GET_PID_NUMBER(pObj->MLMEThr_pid), ret); + } + else + { + //wait_for_completion (&pAd->notify); + wait_for_completion (&pAd->mlmeComplete); + pObj->MLMEThr_pid = THREAD_PID_INIT_VALUE; + } } - BUG_ON(pObj->RTUSBCmdThr_task == NULL); - CHECK_PID_LEGALITY(task_pid(pObj->RTUSBCmdThr_task)) + CHECK_PID_LEGALITY(pObj->RTUSBCmdThr_pid) { - printk(KERN_DEBUG "Terminate the RTUSBCmdThr pid=%d!\n", - pid_nr(task_pid(pObj->RTUSBCmdThr_task))); + printk("Terminate the RTUSBCmdThr_pid=%d!\n", GET_PID_NUMBER(pObj->RTUSBCmdThr_pid)); mb(); NdisAcquireSpinLock(&pAd->CmdQLock); pAd->CmdQ.CmdQState = RT2870_THREAD_STOPED; NdisReleaseSpinLock(&pAd->CmdQLock); mb(); //RTUSBCMDUp(pAd); - kthread_stop(pObj->RTUSBCmdThr_task); - pObj->RTUSBCmdThr_task = NULL; + ret = KILL_THREAD_PID(pObj->RTUSBCmdThr_pid, SIGTERM, 1); + if (ret) + { + printk(KERN_WARNING "%s: unable to RTUSBCmd thread, pid=%d, ret=%d!\n", + pAd->net_dev->name, GET_PID_NUMBER(pObj->RTUSBCmdThr_pid), ret); + } + else + { + //wait_for_completion (&pAd->notify); + wait_for_completion (&pAd->CmdQComplete); + pObj->RTUSBCmdThr_pid = THREAD_PID_INIT_VALUE; + } } #endif #ifdef RT30xx @@ -1045,7 +1068,7 @@ BOOLEAN RT28XXChipsetCheck( dev_p->descriptor.idProduct == rtusb_usb_id[i].idProduct) { #ifndef RT30xx - printk(KERN_DEBUG "rt2870: idVendor = 0x%x, idProduct = 0x%x\n", + printk("rt2870: idVendor = 0x%x, idProduct = 0x%x\n", #endif #ifdef RT30xx printk("rt2870: idVendor = 0x%x, idProduct = 0x%x\n", diff --git a/drivers/staging/rt2870/common/2870_rtmp_init.c b/drivers/staging/rt2870/common/2870_rtmp_init.c index 0f4c8af97e4..80909e9ab5a 100644 --- a/drivers/staging/rt2870/common/2870_rtmp_init.c +++ b/drivers/staging/rt2870/common/2870_rtmp_init.c @@ -700,8 +700,8 @@ NDIS_STATUS AdapterBlockAllocateMemory( usb_dev = pObj->pUsb_Dev; #ifndef RT30xx - pObj->MLMEThr_task = NULL; - pObj->RTUSBCmdThr_task = NULL; + pObj->MLMEThr_pid = THREAD_PID_INIT_VALUE; + pObj->RTUSBCmdThr_pid = THREAD_PID_INIT_VALUE; #endif #ifdef RT30xx pObj->MLMEThr_pid = NULL; @@ -743,7 +743,7 @@ NDIS_STATUS CreateThreads( PRTMP_ADAPTER pAd = net_dev->ml_priv; POS_COOKIE pObj = (POS_COOKIE) pAd->OS_Cookie; #ifndef RT30xx - struct task_struct *tsk; + pid_t pid_number = -1; #endif #ifdef RT30xx pid_t pid_number; @@ -762,10 +762,10 @@ NDIS_STATUS CreateThreads( // Creat MLME Thread #ifndef RT30xx - pObj->MLMEThr_task = NULL; - tsk = kthread_run(MlmeThread, pAd, "%s", pAd->net_dev->name); - - if (IS_ERR(tsk)) { + pObj->MLMEThr_pid= THREAD_PID_INIT_VALUE; + pid_number = kernel_thread(MlmeThread, pAd, CLONE_VM); + if (pid_number < 0) + { #endif #ifdef RT30xx pObj->MLMEThr_pid = NULL; @@ -778,7 +778,7 @@ NDIS_STATUS CreateThreads( } #ifndef RT30xx - pObj->MLMEThr_task = tsk; + pObj->MLMEThr_pid = GET_PID(pid_number); #endif #ifdef RT30xx pObj->MLMEThr_pid = find_get_pid(pid_number); @@ -788,10 +788,9 @@ NDIS_STATUS CreateThreads( // Creat Command Thread #ifndef RT30xx - pObj->RTUSBCmdThr_task = NULL; - tsk = kthread_run(RTUSBCmdThread, pAd, "%s", pAd->net_dev->name); - - if (IS_ERR(tsk) < 0) + pObj->RTUSBCmdThr_pid= THREAD_PID_INIT_VALUE; + pid_number = kernel_thread(RTUSBCmdThread, pAd, CLONE_VM); + if (pid_number < 0) #endif #ifdef RT30xx pObj->RTUSBCmdThr_pid = NULL; @@ -804,7 +803,7 @@ NDIS_STATUS CreateThreads( } #ifndef RT30xx - pObj->RTUSBCmdThr_task = tsk; + pObj->RTUSBCmdThr_pid = GET_PID(pid_number); #endif #ifdef RT30xx pObj->RTUSBCmdThr_pid = find_get_pid(pid_number); @@ -812,9 +811,9 @@ NDIS_STATUS CreateThreads( wait_for_completion(&(pAd->CmdQComplete)); #ifndef RT30xx - pObj->TimerQThr_task = NULL; - tsk = kthread_run(TimerQThread, pAd, "%s", pAd->net_dev->name); - if (IS_ERR(tsk) < 0) + pObj->TimerQThr_pid= THREAD_PID_INIT_VALUE; + pid_number = kernel_thread(TimerQThread, pAd, CLONE_VM); + if (pid_number < 0) #endif #ifdef RT30xx pObj->TimerQThr_pid = NULL; @@ -826,7 +825,7 @@ NDIS_STATUS CreateThreads( return NDIS_STATUS_FAILURE; } #ifndef RT30xx - pObj->TimerQThr_task = tsk; + pObj->TimerQThr_pid = GET_PID(pid_number); #endif #ifdef RT30xx pObj->TimerQThr_pid = find_get_pid(pid_number); diff --git a/drivers/staging/rt2870/common/rtusb_io.c b/drivers/staging/rt2870/common/rtusb_io.c index fd1b0c18f2a..704b5c2d509 100644 --- a/drivers/staging/rt2870/common/rtusb_io.c +++ b/drivers/staging/rt2870/common/rtusb_io.c @@ -984,8 +984,7 @@ NDIS_STATUS RTUSBEnqueueCmdFromNdis( POS_COOKIE pObj = (POS_COOKIE) pAd->OS_Cookie; #ifndef RT30xx - BUG_ON(pObj->RTUSBCmdThr_task == NULL); - CHECK_PID_LEGALITY(task_pid(pObj->RTUSBCmdThr_task)) + CHECK_PID_LEGALITY(pObj->RTUSBCmdThr_pid) #endif #ifdef RT30xx if (pObj->RTUSBCmdThr_pid < 0) diff --git a/drivers/staging/rt2870/rt2870.h b/drivers/staging/rt2870/rt2870.h index 10e1640d61e..2b8872b2fd9 100644 --- a/drivers/staging/rt2870/rt2870.h +++ b/drivers/staging/rt2870/rt2870.h @@ -590,16 +590,14 @@ VOID RTUSBBulkRxComplete(purbb_t pUrb, struct pt_regs *pt_regs); #define RTUSBMlmeUp(pAd) \ { \ POS_COOKIE pObj = (POS_COOKIE) pAd->OS_Cookie; \ - BUG_ON(pObj->MLMEThr_task == NULL); \ - CHECK_PID_LEGALITY(task_pid(pObj->MLMEThr_task)) \ + CHECK_PID_LEGALITY(pObj->MLMEThr_pid) \ up(&(pAd->mlme_semaphore)); \ } #define RTUSBCMDUp(pAd) \ { \ POS_COOKIE pObj = (POS_COOKIE) pAd->OS_Cookie; \ - BUG_ON(pObj->RTUSBCmdThr_task == NULL); \ - CHECK_PID_LEGALITY(task_pid(pObj->RTUSBCmdThr_task)) \ + CHECK_PID_LEGALITY(pObj->RTUSBCmdThr_pid) \ up(&(pAd->RTUSBCmd_semaphore)); \ } #endif -- GitLab From ce9c010c5c39df05ed81a06aba492c45ee0c6f19 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Tue, 4 Aug 2009 16:53:36 -0700 Subject: [PATCH 0924/1342] Staging: rtl8192su: fix build error This fixes a build error when selecting the rtl8192su driver as a module. This has been reported by me, and the opensuse kernel developer team, and I finally tracked it down. Signed-off-by: Greg Kroah-Hartman --- drivers/staging/rtl8192su/ieee80211.h | 2 +- drivers/staging/rtl8192su/ieee80211/ieee80211.h | 2 +- drivers/staging/rtl8192su/ieee80211/ieee80211_tx.c | 3 ++- drivers/staging/rtl8192su/r8192U_core.c | 2 +- 4 files changed, 5 insertions(+), 4 deletions(-) diff --git a/drivers/staging/rtl8192su/ieee80211.h b/drivers/staging/rtl8192su/ieee80211.h index 0edb09a536f..ea973931803 100644 --- a/drivers/staging/rtl8192su/ieee80211.h +++ b/drivers/staging/rtl8192su/ieee80211.h @@ -2645,7 +2645,7 @@ extern int ieee80211_encrypt_fragment( struct sk_buff *frag, int hdr_len); -extern int ieee80211_xmit(struct sk_buff *skb, +extern int rtl8192_ieee80211_xmit(struct sk_buff *skb, struct net_device *dev); extern void ieee80211_txb_free(struct ieee80211_txb *); diff --git a/drivers/staging/rtl8192su/ieee80211/ieee80211.h b/drivers/staging/rtl8192su/ieee80211/ieee80211.h index 720bfcbfadc..5e3a2cbed2b 100644 --- a/drivers/staging/rtl8192su/ieee80211/ieee80211.h +++ b/drivers/staging/rtl8192su/ieee80211/ieee80211.h @@ -2645,7 +2645,7 @@ extern int ieee80211_encrypt_fragment( struct sk_buff *frag, int hdr_len); -extern int ieee80211_xmit(struct sk_buff *skb, +extern int rtl8192_ieee80211_xmit(struct sk_buff *skb, struct net_device *dev); extern void ieee80211_txb_free(struct ieee80211_txb *); diff --git a/drivers/staging/rtl8192su/ieee80211/ieee80211_tx.c b/drivers/staging/rtl8192su/ieee80211/ieee80211_tx.c index 7294572b990..cba12b84be5 100644 --- a/drivers/staging/rtl8192su/ieee80211/ieee80211_tx.c +++ b/drivers/staging/rtl8192su/ieee80211/ieee80211_tx.c @@ -618,7 +618,7 @@ void ieee80211_query_seqnum(struct ieee80211_device*ieee, struct sk_buff* skb, u } } -int ieee80211_xmit(struct sk_buff *skb, struct net_device *dev) +int rtl8192_ieee80211_xmit(struct sk_buff *skb, struct net_device *dev) { #if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,5,0)) struct ieee80211_device *ieee = netdev_priv(dev); @@ -943,5 +943,6 @@ int ieee80211_xmit(struct sk_buff *skb, struct net_device *dev) return 1; } +EXPORT_SYMBOL(rtl8192_ieee80211_xmit); EXPORT_SYMBOL(ieee80211_txb_free); diff --git a/drivers/staging/rtl8192su/r8192U_core.c b/drivers/staging/rtl8192su/r8192U_core.c index 4ab250743e8..70f81a8f129 100644 --- a/drivers/staging/rtl8192su/r8192U_core.c +++ b/drivers/staging/rtl8192su/r8192U_core.c @@ -12142,7 +12142,7 @@ static const struct net_device_ops rtl8192_netdev_ops = { .ndo_set_mac_address = r8192_set_mac_adr, .ndo_validate_addr = eth_validate_addr, .ndo_change_mtu = eth_change_mtu, - .ndo_start_xmit = ieee80211_xmit, + .ndo_start_xmit = rtl8192_ieee80211_xmit, }; #if LINUX_VERSION_CODE > KERNEL_VERSION(2,5,0) -- GitLab From 5fb4d2525b6dcffbb8bc26a7dfc7ed17ad323a06 Mon Sep 17 00:00:00 2001 From: Jeff Mahoney Date: Fri, 7 Aug 2009 16:12:03 -0700 Subject: [PATCH 0925/1342] staging: add dependencies on PCI for drivers that require it This patch adds PCI dependencies to staging drivers that require it. Signed-off-by: Jeff Mahoney Signed-off-by: Greg Kroah-Hartman --- drivers/staging/b3dfg/Kconfig | 1 + drivers/staging/heci/Kconfig | 1 + 2 files changed, 2 insertions(+) diff --git a/drivers/staging/b3dfg/Kconfig b/drivers/staging/b3dfg/Kconfig index 524231047de..9e6573cf97d 100644 --- a/drivers/staging/b3dfg/Kconfig +++ b/drivers/staging/b3dfg/Kconfig @@ -1,5 +1,6 @@ config B3DFG tristate "Brontes 3d Frame Framegrabber" + depends on PCI default n ---help--- This driver provides support for the Brontes 3d Framegrabber diff --git a/drivers/staging/heci/Kconfig b/drivers/staging/heci/Kconfig index ae8d588d3a2..c7206f8bcd9 100644 --- a/drivers/staging/heci/Kconfig +++ b/drivers/staging/heci/Kconfig @@ -1,5 +1,6 @@ config HECI tristate "Intel Management Engine Interface (MEI) Support" + depends on PCI ---help--- The Intel Management Engine Interface (Intel MEI) driver allows applications to access the Active Management Technology -- GitLab From 749d00dbf154fc2f9ac59df669205039de0d5b45 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Fri, 7 Aug 2009 21:00:10 +0200 Subject: [PATCH 0926/1342] Staging: rspiusb: Fix buffer overflow usb_buffer_map_sg() may return -1. This will result in a read from pdx->PixelUrb[frameInfo][-1] Signed-off-by: Roel Kluin Signed-off-by: Greg Kroah-Hartman --- drivers/staging/rspiusb/rspiusb.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/staging/rspiusb/rspiusb.c b/drivers/staging/rspiusb/rspiusb.c index 2f8155c1968..04e2f92c0f6 100644 --- a/drivers/staging/rspiusb/rspiusb.c +++ b/drivers/staging/rspiusb/rspiusb.c @@ -716,6 +716,8 @@ static int MapUserBuffer(struct ioctl_struct *io, struct device_extension *pdx) pdx->PixelUrb[frameInfo][i]->transfer_flags = URB_NO_TRANSFER_DMA_MAP | URB_NO_INTERRUPT; } + if (i == 0) + return -EINVAL; /* only interrupt when last URB completes */ pdx->PixelUrb[frameInfo][--i]->transfer_flags &= ~URB_NO_INTERRUPT; pdx->pendedPixelUrbs[frameInfo] = -- GitLab From 087d7e56deffb611a098e7e257388a41edbeef1f Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Tue, 4 Aug 2009 08:59:59 -0700 Subject: [PATCH 0927/1342] x86: Fix MSI-X initialization by using online_mask for x2apic target_cpus found a system where x2apic reports an MSI-X irq initialization failure: [ 302.859446] igbvf 0000:81:10.4: enabling device (0000 -> 0002) [ 302.874369] igbvf 0000:81:10.4: using 64bit DMA mask [ 302.879023] igbvf 0000:81:10.4: using 64bit consistent DMA mask [ 302.894386] igbvf 0000:81:10.4: enabling bus mastering [ 302.898171] igbvf 0000:81:10.4: setting latency timer to 64 [ 302.914050] reserve_memtype added 0xefb08000-0xefb0c000, track uncached-minus, req uncached-minus, ret uncached-minus [ 302.933839] reserve_memtype added 0xefb28000-0xefb29000, track uncached-minus, req uncached-minus, ret uncached-minus [ 302.940367] alloc irq_desc for 265 on node 4 [ 302.956874] alloc kstat_irqs on node 4 [ 302.959452] alloc irq_2_iommu on node 0 [ 302.974328] igbvf 0000:81:10.4: irq 265 for MSI/MSI-X [ 302.977778] alloc irq_desc for 266 on node 4 [ 302.980347] alloc kstat_irqs on node 4 [ 302.995312] free_memtype request 0xefb28000-0xefb29000 [ 302.998816] igbvf 0000:81:10.4: Failed to initialize MSI-X interrupts. ... it turns out that when trying to enable MSI-X, __assign_irq_vector(new, cfg_new, apic->target_cpus()) can not get vector because for x2apic target-cpus returns cpumask_of(0) Update that to online_mask like xapic. Signed-off-by: Yinghai Lu Acked-by: Suresh Siddha LKML-Reference: <4A785AFF.3050902@kernel.org> Signed-off-by: Ingo Molnar --- arch/x86/kernel/apic/x2apic_cluster.c | 8 +++++--- arch/x86/kernel/apic/x2apic_phys.c | 8 +++++--- 2 files changed, 10 insertions(+), 6 deletions(-) diff --git a/arch/x86/kernel/apic/x2apic_cluster.c b/arch/x86/kernel/apic/x2apic_cluster.c index 2ed4e2bb3b3..a5371ec3677 100644 --- a/arch/x86/kernel/apic/x2apic_cluster.c +++ b/arch/x86/kernel/apic/x2apic_cluster.c @@ -17,11 +17,13 @@ static int x2apic_acpi_madt_oem_check(char *oem_id, char *oem_table_id) return x2apic_enabled(); } -/* Start with all IRQs pointing to boot CPU. IRQ balancing will shift them. */ - +/* + * need to use more than cpu 0, because we need more vectors when + * MSI-X are used. + */ static const struct cpumask *x2apic_target_cpus(void) { - return cpumask_of(0); + return cpu_online_mask; } /* diff --git a/arch/x86/kernel/apic/x2apic_phys.c b/arch/x86/kernel/apic/x2apic_phys.c index 0b631c6a2e0..a8989aadc99 100644 --- a/arch/x86/kernel/apic/x2apic_phys.c +++ b/arch/x86/kernel/apic/x2apic_phys.c @@ -27,11 +27,13 @@ static int x2apic_acpi_madt_oem_check(char *oem_id, char *oem_table_id) return 0; } -/* Start with all IRQs pointing to boot CPU. IRQ balancing will shift them. */ - +/* + * need to use more than cpu 0, because we need more vectors when + * MSI-X are used. + */ static const struct cpumask *x2apic_target_cpus(void) { - return cpumask_of(0); + return cpu_online_mask; } static void x2apic_vector_allocation_domain(int cpu, struct cpumask *retmask) -- GitLab From ad7d6c7a0654a4bbda3e109f56af713267e96274 Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Tue, 4 Aug 2009 09:01:33 -0700 Subject: [PATCH 0928/1342] x86/irq: Fix move_irq_desc() for nodes without ram Don't move it if target node is -1. Signed-off-by: Yinghai Lu LKML-Reference: <4A785B5D.4070702@kernel.org> Signed-off-by: Ingo Molnar --- kernel/irq/numa_migrate.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/kernel/irq/numa_migrate.c b/kernel/irq/numa_migrate.c index 2f69bee57bf..3fd30197da2 100644 --- a/kernel/irq/numa_migrate.c +++ b/kernel/irq/numa_migrate.c @@ -107,8 +107,8 @@ out_unlock: struct irq_desc *move_irq_desc(struct irq_desc *desc, int node) { - /* those all static, do move them */ - if (desc->irq < NR_IRQS_LEGACY) + /* those static or target node is -1, do not move them */ + if (desc->irq < NR_IRQS_LEGACY || node == -1) return desc; if (desc->node != node) -- GitLab From 498cdbfbcf98e0d2c90a26e6a02a82f043876e48 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Ozan=20=C3=87a=C4=9Flayan?= Date: Tue, 4 Aug 2009 19:39:31 +0300 Subject: [PATCH 0929/1342] x86: Add quirk to make Apple MacBookPro5,1 use reboot=pci MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit MacBookPro5,1 is not able to reboot unless reboot=pci is set. This patch forces it through a DMI quirk specific to this device. Signed-off-by: Ozan ÇaÄŸlayan LKML-Reference: <1249403971-6543-1-git-send-email-ozan@pardus.org.tr> Signed-off-by: Ingo Molnar --- arch/x86/kernel/reboot.c | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-) diff --git a/arch/x86/kernel/reboot.c b/arch/x86/kernel/reboot.c index 834c9da8bf9..9eb89760370 100644 --- a/arch/x86/kernel/reboot.c +++ b/arch/x86/kernel/reboot.c @@ -405,7 +405,7 @@ EXPORT_SYMBOL(machine_real_restart); #endif /* CONFIG_X86_32 */ /* - * Apple MacBook5,2 (2009 MacBook) needs reboot=p + * Some Apple MacBook and MacBookPro's needs reboot=p to be able to reboot */ static int __init set_pci_reboot(const struct dmi_system_id *d) { @@ -426,6 +426,14 @@ static struct dmi_system_id __initdata pci_reboot_dmi_table[] = { DMI_MATCH(DMI_PRODUCT_NAME, "MacBook5,2"), }, }, + { /* Handle problems with rebooting on Apple MacBookPro5,1 */ + .callback = set_pci_reboot, + .ident = "Apple MacBookPro5,1", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Apple Inc."), + DMI_MATCH(DMI_PRODUCT_NAME, "MacBookPro5,1"), + }, + }, { } }; -- GitLab From 96b2de313b1e0e02aea80ee47df6a2b5cbdf8e13 Mon Sep 17 00:00:00 2001 From: Tom Zanussi Date: Sat, 8 Aug 2009 10:49:09 -0500 Subject: [PATCH 0930/1342] tracing/filters: Don't use pred on alloc failure Dan Carpenter sent me a fix to prevent pred from being used if it couldn't be allocated. I noticed the same problem also existed for the create_pred() case and added a fix for that. Reported-by: Dan Carpenter Signed-off-by: Tom Zanussi Cc: Steven Rostedt Cc: Frederic Weisbecker Cc: Li Zefan LKML-Reference: <1249746549.6453.29.camel@tropicana> Signed-off-by: Ingo Molnar --- kernel/trace/trace_events_filter.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/kernel/trace/trace_events_filter.c b/kernel/trace/trace_events_filter.c index 936c621bbf4..1557148be34 100644 --- a/kernel/trace/trace_events_filter.c +++ b/kernel/trace/trace_events_filter.c @@ -1029,6 +1029,8 @@ static int replace_preds(struct event_subsystem *system, if (elt->op == OP_AND || elt->op == OP_OR) { pred = create_logical_pred(elt->op); + if (!pred) + return -ENOMEM; if (call) { err = filter_add_pred(ps, call, pred); filter_free_pred(pred); @@ -1048,6 +1050,8 @@ static int replace_preds(struct event_subsystem *system, } pred = create_pred(elt->op, operand1, operand2); + if (!pred) + return -ENOMEM; if (call) { err = filter_add_pred(ps, call, pred); filter_free_pred(pred); -- GitLab From 26528e773ecc74fb1b61b7275f86f761cbb340ec Mon Sep 17 00:00:00 2001 From: Tom Zanussi Date: Sat, 8 Aug 2009 10:49:53 -0500 Subject: [PATCH 0931/1342] tracing/filters: Always free pred on filter_add_subsystem_pred() failure If filter_add_subsystem_pred() fails due to ENOSPC or ENOMEM, the pred doesn't get freed, while as a side effect it does for other errors. Make it so the caller always frees the pred for any error. Signed-off-by: Tom Zanussi Cc: Steven Rostedt Cc: Frederic Weisbecker Cc: Li Zefan LKML-Reference: <1249746593.6453.32.camel@tropicana> Signed-off-by: Ingo Molnar --- kernel/trace/trace_events_filter.c | 16 +++++++++++----- 1 file changed, 11 insertions(+), 5 deletions(-) diff --git a/kernel/trace/trace_events_filter.c b/kernel/trace/trace_events_filter.c index 1557148be34..f32dc9d1ea7 100644 --- a/kernel/trace/trace_events_filter.c +++ b/kernel/trace/trace_events_filter.c @@ -624,9 +624,6 @@ static int filter_add_subsystem_pred(struct filter_parse_state *ps, return -ENOSPC; } - filter->preds[filter->n_preds] = pred; - filter->n_preds++; - list_for_each_entry(call, &ftrace_events, list) { if (!call->define_fields) @@ -643,6 +640,9 @@ static int filter_add_subsystem_pred(struct filter_parse_state *ps, } replace_filter_string(call->filter, filter_string); } + + filter->preds[filter->n_preds] = pred; + filter->n_preds++; out: return err; } @@ -1034,9 +1034,12 @@ static int replace_preds(struct event_subsystem *system, if (call) { err = filter_add_pred(ps, call, pred); filter_free_pred(pred); - } else + } else { err = filter_add_subsystem_pred(ps, system, pred, filter_string); + if (err) + filter_free_pred(pred); + } if (err) return err; @@ -1055,9 +1058,12 @@ static int replace_preds(struct event_subsystem *system, if (call) { err = filter_add_pred(ps, call, pred); filter_free_pred(pred); - } else + } else { err = filter_add_subsystem_pred(ps, system, pred, filter_string); + if (err) + filter_free_pred(pred); + } if (err) return err; -- GitLab From 17d42c1c497aa54952b9e58c1502a46f0df40315 Mon Sep 17 00:00:00 2001 From: Stanislaw Gruszka Date: Thu, 6 Aug 2009 16:03:30 -0700 Subject: [PATCH 0932/1342] posix_cpu_timers_exit_group(): Do not use thread_group_cputimer() When the process exits we don't have to run new cputimer nor use running one (as it not accounts when tsk->exit_state != 0) to get process CPU times. As there is only one thread we can just use CPU times fields from task and signal structs. Signed-off-by: Stanislaw Gruszka Cc: Peter Zijlstra Cc: Roland McGrath Cc: Vitaly Mayatskikh Signed-off-by: Andrew Morton Signed-off-by: Ingo Molnar --- kernel/posix-cpu-timers.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/kernel/posix-cpu-timers.c b/kernel/posix-cpu-timers.c index bece7c0b67b..e33a21cb940 100644 --- a/kernel/posix-cpu-timers.c +++ b/kernel/posix-cpu-timers.c @@ -521,11 +521,12 @@ void posix_cpu_timers_exit(struct task_struct *tsk) } void posix_cpu_timers_exit_group(struct task_struct *tsk) { - struct task_cputime cputime; + struct signal_struct *const sig = tsk->signal; - thread_group_cputimer(tsk, &cputime); cleanup_timers(tsk->signal->cpu_timers, - cputime.utime, cputime.stime, cputime.sum_exec_runtime); + cputime_add(tsk->utime, sig->utime), + cputime_add(tsk->stime, sig->stime), + tsk->se.sum_exec_runtime + sig->sum_sched_runtime); } static void clear_dead_task(struct k_itimer *timer, union cpu_time_count now) -- GitLab From 38d5487db7f289be1d56ac7df704ee49ed3213b9 Mon Sep 17 00:00:00 2001 From: Keith Packard Date: Mon, 20 Jul 2009 14:49:17 -0700 Subject: [PATCH 0933/1342] drm: When adding probed modes, preserve duplicate mode types The code which takes probed modes and adds them to a connector eliminates duplicate modes by comparing them using drm_mode_equal. That function doesn't consider the type bits, which means that any modes which differ only in the type field will be lost. One of the bits in the mode->type field is the DRM_MODE_TYPE_PREFERRED bit. If the mode with that bit is lost, then higher level code will not know which mode to select, causing a random mode to be used instead. This patch simply merges the two mode type bits together; that seems reasonable to me, but perhaps only a subset of the bits should be used? None of these can be user defined as they all come from looking at just the hardware. Signed-off-by: Keith Packard Signed-off-by: Dave Airlie --- drivers/gpu/drm/drm_modes.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/gpu/drm/drm_modes.c b/drivers/gpu/drm/drm_modes.c index 54f492a488a..7914097b09c 100644 --- a/drivers/gpu/drm/drm_modes.c +++ b/drivers/gpu/drm/drm_modes.c @@ -566,6 +566,8 @@ void drm_mode_connector_list_update(struct drm_connector *connector) found_it = 1; /* if equal delete the probed mode */ mode->status = pmode->status; + /* Merge type bits together */ + mode->type |= pmode->type; list_del(&pmode->head); drm_mode_destroy(connector->dev, pmode); break; -- GitLab From 8d3457ec3198a569dd14dc9e3ae8b6163bcaa0b5 Mon Sep 17 00:00:00 2001 From: Paul Rolland Date: Sun, 9 Aug 2009 12:24:01 +1000 Subject: [PATCH 0934/1342] drm: silence pointless vblank warning. Some applications/hardware combinations are triggering the message "failed to acquire vblank counter" to be issued up to 20 times a second, which makes it both useless and dangerous, as this may hide other important messages. This changes makes it only appear when people are debugging. Signed-off-by: Paul Rolland Reviewed-by: Jesse Barnes Lost-twice-by: Dave Airlie Signed-off-by: Dave Airlie --- drivers/gpu/drm/drm_irq.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/gpu/drm/drm_irq.c b/drivers/gpu/drm/drm_irq.c index b4a3dbcebe9..f85aaf21e78 100644 --- a/drivers/gpu/drm/drm_irq.c +++ b/drivers/gpu/drm/drm_irq.c @@ -566,7 +566,7 @@ int drm_wait_vblank(struct drm_device *dev, void *data, ret = drm_vblank_get(dev, crtc); if (ret) { - DRM_ERROR("failed to acquire vblank counter, %d\n", ret); + DRM_DEBUG("failed to acquire vblank counter, %d\n", ret); return ret; } seq = drm_vblank_count(dev, crtc); -- GitLab From 6cb504c29b1338925c83e4430e42a51eaa43781e Mon Sep 17 00:00:00 2001 From: Frans Pop Date: Sun, 9 Aug 2009 12:25:29 +1000 Subject: [PATCH 0935/1342] drm/i915: silence vblank warnings these errors are pretty pointless Reviewed-by: Jesse Barnes Signed-off-by: Dave Airlie --- drivers/gpu/drm/i915/i915_irq.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c index 83aee80e77a..7ebc84c2881 100644 --- a/drivers/gpu/drm/i915/i915_irq.c +++ b/drivers/gpu/drm/i915/i915_irq.c @@ -190,7 +190,7 @@ u32 i915_get_vblank_counter(struct drm_device *dev, int pipe) low_frame = pipe ? PIPEBFRAMEPIXEL : PIPEAFRAMEPIXEL; if (!i915_pipe_enabled(dev, pipe)) { - DRM_ERROR("trying to get vblank count for disabled pipe %d\n", pipe); + DRM_DEBUG("trying to get vblank count for disabled pipe %d\n", pipe); return 0; } @@ -219,7 +219,7 @@ u32 gm45_get_vblank_counter(struct drm_device *dev, int pipe) int reg = pipe ? PIPEB_FRMCOUNT_GM45 : PIPEA_FRMCOUNT_GM45; if (!i915_pipe_enabled(dev, pipe)) { - DRM_ERROR("trying to get vblank count for disabled pipe %d\n", pipe); + DRM_DEBUG("trying to get vblank count for disabled pipe %d\n", pipe); return 0; } -- GitLab From fdb8a42742ac95606668f73481dfb2f760658fdd Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Thu, 6 Aug 2009 15:58:13 -0700 Subject: [PATCH 0936/1342] x86: fix buffer overflow in efi_init() If the vendor name (from c16) can be longer than 100 bytes (or missing a terminating null), then the null is written past the end of vendor[]. Found with Parfait, http://research.sun.com/projects/parfait/ Signed-off-by: Roel Kluin Cc: Ingo Molnar Signed-off-by: Andrew Morton Signed-off-by: H. Peter Anvin Cc: Huang Ying --- arch/x86/kernel/efi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/efi.c b/arch/x86/kernel/efi.c index 19ccf6d0dcc..fe26ba3e345 100644 --- a/arch/x86/kernel/efi.c +++ b/arch/x86/kernel/efi.c @@ -354,7 +354,7 @@ void __init efi_init(void) */ c16 = tmp = early_ioremap(efi.systab->fw_vendor, 2); if (c16) { - for (i = 0; i < sizeof(vendor) && *c16; ++i) + for (i = 0; i < sizeof(vendor) - 1 && *c16; ++i) vendor[i] = *c16++; vendor[i] = '\0'; } else -- GitLab From b4a2f5e723e4f7df46731106faf9e2405673c073 Mon Sep 17 00:00:00 2001 From: Gleb Natapov Date: Sun, 5 Jul 2009 18:48:11 +0300 Subject: [PATCH 0937/1342] KVM: Avoid redelivery of edge interrupt before next edge The check for an edge is broken in current ioapic code. ioapic->irr is cleared on each edge interrupt by ioapic_service() and this makes old_irr != ioapic->irr condition in kvm_ioapic_set_irq() to be always true. The patch fixes the code to properly recognise edge. Some HW emulation calls set_irq() without level change. If each such call is propagated to an OS it may confuse a device driver. This is the case with keyboard device emulation and Windows XP x64 installer on SMP VM. Each keystroke produce two interrupts (down/up) one interrupt is submitted to CPU0 and another to CPU1. This confuses Windows somehow and it ignores keystrokes. Signed-off-by: Gleb Natapov Signed-off-by: Avi Kivity --- virt/kvm/ioapic.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/virt/kvm/ioapic.c b/virt/kvm/ioapic.c index 1eddae94bab..1150c6d5c7b 100644 --- a/virt/kvm/ioapic.c +++ b/virt/kvm/ioapic.c @@ -95,8 +95,6 @@ static int ioapic_service(struct kvm_ioapic *ioapic, unsigned int idx) if (injected && pent->fields.trig_mode == IOAPIC_LEVEL_TRIG) pent->fields.remote_irr = 1; } - if (!pent->fields.trig_mode) - ioapic->irr &= ~(1 << idx); return injected; } @@ -136,7 +134,8 @@ static void ioapic_write_indirect(struct kvm_ioapic *ioapic, u32 val) mask_after = ioapic->redirtbl[index].fields.mask; if (mask_before != mask_after) kvm_fire_mask_notifiers(ioapic->kvm, index, mask_after); - if (ioapic->irr & (1 << index)) + if (ioapic->redirtbl[index].fields.trig_mode == IOAPIC_LEVEL_TRIG + && ioapic->irr & (1 << index)) ioapic_service(ioapic, index); break; } @@ -184,9 +183,10 @@ int kvm_ioapic_set_irq(struct kvm_ioapic *ioapic, int irq, int level) if (!level) ioapic->irr &= ~mask; else { + int edge = (entry.fields.trig_mode == IOAPIC_EDGE_TRIG); ioapic->irr |= mask; - if ((!entry.fields.trig_mode && old_irr != ioapic->irr) - || !entry.fields.remote_irr) + if ((edge && old_irr != ioapic->irr) || + (!edge && !entry.fields.remote_irr)) ret = ioapic_service(ioapic, irq); } } -- GitLab From 3a6593050fbd8bbcaed3a44d01c31d907315c86c Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Tue, 21 Jul 2009 17:34:57 +0200 Subject: [PATCH 0938/1342] perf_counter, ftrace: Fix perf_counter integration Adds possible second part to the assign argument of TP_EVENT(). TP_perf_assign( __perf_count(foo); __perf_addr(bar); ) Which, when specified make the swcounter increment with @foo instead of the usual 1, and report @bar for PERF_SAMPLE_ADDR (data address associated with the event) when this triggers a counter overflow. Signed-off-by: Peter Zijlstra Acked-by: Steven Rostedt Cc: Frederic Weisbecker Cc: Jason Baron Cc: Paul Mackerras Signed-off-by: Ingo Molnar --- include/trace/ftrace.h | 110 +++++++++++++++++++++++++++++++---------- kernel/perf_counter.c | 6 +-- 2 files changed, 88 insertions(+), 28 deletions(-) diff --git a/include/trace/ftrace.h b/include/trace/ftrace.h index 1867553c61e..fec71f8dbc4 100644 --- a/include/trace/ftrace.h +++ b/include/trace/ftrace.h @@ -144,6 +144,9 @@ #undef TP_fast_assign #define TP_fast_assign(args...) args +#undef TP_perf_assign +#define TP_perf_assign(args...) + #undef TRACE_EVENT #define TRACE_EVENT(call, proto, args, tstruct, func, print) \ static int \ @@ -345,6 +348,88 @@ static inline int ftrace_get_offsets_##call( \ #include TRACE_INCLUDE(TRACE_INCLUDE_FILE) +#ifdef CONFIG_EVENT_PROFILE + +/* + * Generate the functions needed for tracepoint perf_counter support. + * + * static void ftrace_profile_(proto) + * { + * extern void perf_tpcounter_event(int, u64, u64); + * u64 __addr = 0, __count = 1; + * + * <-- here we expand the TP_perf_assign() macro + * + * perf_tpcounter_event(event_.id, __addr, __count); + * } + * + * static int ftrace_profile_enable_(struct ftrace_event_call *event_call) + * { + * int ret = 0; + * + * if (!atomic_inc_return(&event_call->profile_count)) + * ret = register_trace_(ftrace_profile_); + * + * return ret; + * } + * + * static void ftrace_profile_disable_(struct ftrace_event_call *event_call) + * { + * if (atomic_add_negative(-1, &event->call->profile_count)) + * unregister_trace_(ftrace_profile_); + * } + * + */ + +#undef TP_fast_assign +#define TP_fast_assign(args...) + +#undef TP_perf_assign +#define TP_perf_assign(args...) args + +#undef __perf_addr +#define __perf_addr(a) __addr = (a) + +#undef __perf_count +#define __perf_count(c) __count = (c) + +#undef TRACE_EVENT +#define TRACE_EVENT(call, proto, args, tstruct, assign, print) \ + \ +static void ftrace_profile_##call(proto) \ +{ \ + extern void perf_tpcounter_event(int, u64, u64); \ + u64 __addr = 0, __count = 1; \ + { assign; } \ + perf_tpcounter_event(event_##call.id, __addr, __count); \ +} \ + \ +static int ftrace_profile_enable_##call(struct ftrace_event_call *event_call) \ +{ \ + int ret = 0; \ + \ + if (!atomic_inc_return(&event_call->profile_count)) \ + ret = register_trace_##call(ftrace_profile_##call); \ + \ + return ret; \ +} \ + \ +static void ftrace_profile_disable_##call(struct ftrace_event_call *event_call)\ +{ \ + if (atomic_add_negative(-1, &event_call->profile_count)) \ + unregister_trace_##call(ftrace_profile_##call); \ +} + +#include TRACE_INCLUDE(TRACE_INCLUDE_FILE) + +#undef TP_fast_assign +#define TP_fast_assign(args...) args + +#undef TP_perf_assign +#define TP_perf_assign(args...) + +#endif + /* * Stage 4 of the trace events. * @@ -447,28 +532,6 @@ static inline int ftrace_get_offsets_##call( \ #define TP_FMT(fmt, args...) fmt "\n", ##args #ifdef CONFIG_EVENT_PROFILE -#define _TRACE_PROFILE(call, proto, args) \ -static void ftrace_profile_##call(proto) \ -{ \ - extern void perf_tpcounter_event(int); \ - perf_tpcounter_event(event_##call.id); \ -} \ - \ -static int ftrace_profile_enable_##call(struct ftrace_event_call *event_call) \ -{ \ - int ret = 0; \ - \ - if (!atomic_inc_return(&event_call->profile_count)) \ - ret = register_trace_##call(ftrace_profile_##call); \ - \ - return ret; \ -} \ - \ -static void ftrace_profile_disable_##call(struct ftrace_event_call *event_call)\ -{ \ - if (atomic_add_negative(-1, &event_call->profile_count)) \ - unregister_trace_##call(ftrace_profile_##call); \ -} #define _TRACE_PROFILE_INIT(call) \ .profile_count = ATOMIC_INIT(-1), \ @@ -476,7 +539,6 @@ static void ftrace_profile_disable_##call(struct ftrace_event_call *event_call)\ .profile_disable = ftrace_profile_disable_##call, #else -#define _TRACE_PROFILE(call, proto, args) #define _TRACE_PROFILE_INIT(call) #endif @@ -502,7 +564,6 @@ static void ftrace_profile_disable_##call(struct ftrace_event_call *event_call)\ #undef TRACE_EVENT #define TRACE_EVENT(call, proto, args, tstruct, assign, print) \ -_TRACE_PROFILE(call, PARAMS(proto), PARAMS(args)) \ \ static struct ftrace_event_call event_##call; \ \ @@ -586,6 +647,5 @@ __attribute__((section("_ftrace_events"))) event_##call = { \ #include TRACE_INCLUDE(TRACE_INCLUDE_FILE) -#undef _TRACE_PROFILE #undef _TRACE_PROFILE_INIT diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index 673c1aaf733..52eb4b68d34 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -3703,17 +3703,17 @@ static const struct pmu perf_ops_task_clock = { }; #ifdef CONFIG_EVENT_PROFILE -void perf_tpcounter_event(int event_id) +void perf_tpcounter_event(int event_id, u64 addr, u64 count) { struct perf_sample_data data = { .regs = get_irq_regs(), - .addr = 0, + .addr = addr, }; if (!data.regs) data.regs = task_pt_regs(current); - do_perf_swcounter_event(PERF_TYPE_TRACEPOINT, event_id, 1, 1, &data); + do_perf_swcounter_event(PERF_TYPE_TRACEPOINT, event_id, count, 1, &data); } EXPORT_SYMBOL_GPL(perf_tpcounter_event); -- GitLab From f413cdb80ce00ec1a4d0ab949b5d96c81cae7f75 Mon Sep 17 00:00:00 2001 From: Frederic Weisbecker Date: Fri, 7 Aug 2009 01:25:54 +0200 Subject: [PATCH 0939/1342] perf_counter: Fix/complete ftrace event records sampling This patch implements the kernel side support for ftrace event record sampling. A new counter sampling attribute is added: PERF_SAMPLE_TP_RECORD which requests ftrace events record sampling. In this case if a PERF_TYPE_TRACEPOINT counter is active and a tracepoint fires, we emit the tracepoint binary record to the perfcounter event buffer, as a sample. Result, after setting PERF_SAMPLE_TP_RECORD attribute from perf record: perf record -f -F 1 -a -e workqueue:workqueue_execution perf report -D 0x21e18 [0x48]: event: 9 . . ... raw event: size 72 bytes . 0000: 09 00 00 00 01 00 48 00 d0 c7 00 81 ff ff ff ff ......H........ . 0010: 0a 00 00 00 0a 00 00 00 21 00 00 00 00 00 00 00 ........!...... . 0020: 2b 00 01 02 0a 00 00 00 0a 00 00 00 65 76 65 6e +...........eve . 0030: 74 73 2f 31 00 00 00 00 00 00 00 00 0a 00 00 00 ts/1........... . 0040: e0 b1 31 81 ff ff ff ff ....... . 0x21e18 [0x48]: PERF_EVENT_SAMPLE (IP, 1): 10: 0xffffffff8100c7d0 period: 33 The raw ftrace binary record starts at offset 0020. Translation: struct trace_entry { type = 0x2b = 43; flags = 1; preempt_count = 2; pid = 0xa = 10; tgid = 0xa = 10; } thread_comm = "events/1" thread_pid = 0xa = 10; func = 0xffffffff8131b1e0 = flush_to_ldisc() What will come next? - Userspace support ('perf trace'), 'flight data recorder' mode for perf trace, etc. - The unconditional copy from the profiling callback brings some costs however if someone wants no such sampling to occur, and needs to be fixed in the future. For that we need to have an instant access to the perf counter attribute. This is a matter of a flag to add in the struct ftrace_event. - Take care of the events recursivity! Don't ever try to record a lock event for example, it seems some locking is used in the profiling fast path and lead to a tracing recursivity. That will be fixed using raw spinlock or recursivity protection. - [...] - Profit! :-) Signed-off-by: Frederic Weisbecker Cc: Li Zefan Cc: Tom Zanussi Cc: Arnaldo Carvalho de Melo Cc: Peter Zijlstra Cc: Mike Galbraith Cc: Steven Rostedt Cc: Paul Mackerras Cc: Pekka Enberg Cc: Gabriel Munteanu Cc: Lai Jiangshan Signed-off-by: Ingo Molnar --- include/linux/ftrace_event.h | 4 +- include/linux/perf_counter.h | 9 ++- include/trace/ftrace.h | 130 ++++++++++++++++++++++++++--------- kernel/perf_counter.c | 18 ++++- kernel/trace/trace.c | 1 + kernel/trace/trace.h | 4 -- tools/perf/builtin-record.c | 1 + 7 files changed, 126 insertions(+), 41 deletions(-) diff --git a/include/linux/ftrace_event.h b/include/linux/ftrace_event.h index d7cd193c227..a81170de7f6 100644 --- a/include/linux/ftrace_event.h +++ b/include/linux/ftrace_event.h @@ -89,7 +89,9 @@ enum print_line_t { TRACE_TYPE_NO_CONSUME = 3 /* Handled but ask to not consume */ }; - +void tracing_generic_entry_update(struct trace_entry *entry, + unsigned long flags, + int pc); struct ring_buffer_event * trace_current_buffer_lock_reserve(int type, unsigned long len, unsigned long flags, int pc); diff --git a/include/linux/perf_counter.h b/include/linux/perf_counter.h index e604e6ef72d..a67dd5c5b6d 100644 --- a/include/linux/perf_counter.h +++ b/include/linux/perf_counter.h @@ -121,8 +121,9 @@ enum perf_counter_sample_format { PERF_SAMPLE_CPU = 1U << 7, PERF_SAMPLE_PERIOD = 1U << 8, PERF_SAMPLE_STREAM_ID = 1U << 9, + PERF_SAMPLE_TP_RECORD = 1U << 10, - PERF_SAMPLE_MAX = 1U << 10, /* non-ABI */ + PERF_SAMPLE_MAX = 1U << 11, /* non-ABI */ }; /* @@ -413,6 +414,11 @@ struct perf_callchain_entry { __u64 ip[PERF_MAX_STACK_DEPTH]; }; +struct perf_tracepoint_record { + int size; + char *record; +}; + struct task_struct; /** @@ -681,6 +687,7 @@ struct perf_sample_data { struct pt_regs *regs; u64 addr; u64 period; + void *private; }; extern int perf_counter_overflow(struct perf_counter *counter, int nmi, diff --git a/include/trace/ftrace.h b/include/trace/ftrace.h index fec71f8dbc4..7fb16d90e7b 100644 --- a/include/trace/ftrace.h +++ b/include/trace/ftrace.h @@ -353,15 +353,7 @@ static inline int ftrace_get_offsets_##call( \ /* * Generate the functions needed for tracepoint perf_counter support. * - * static void ftrace_profile_(proto) - * { - * extern void perf_tpcounter_event(int, u64, u64); - * u64 __addr = 0, __count = 1; - * - * <-- here we expand the TP_perf_assign() macro - * - * perf_tpcounter_event(event_.id, __addr, __count); - * } + * NOTE: The insertion profile callback (ftrace_profile_) is defined later * * static int ftrace_profile_enable_(struct ftrace_event_call *event_call) * { @@ -381,28 +373,10 @@ static inline int ftrace_get_offsets_##call( \ * */ -#undef TP_fast_assign -#define TP_fast_assign(args...) - -#undef TP_perf_assign -#define TP_perf_assign(args...) args - -#undef __perf_addr -#define __perf_addr(a) __addr = (a) - -#undef __perf_count -#define __perf_count(c) __count = (c) - #undef TRACE_EVENT #define TRACE_EVENT(call, proto, args, tstruct, assign, print) \ \ -static void ftrace_profile_##call(proto) \ -{ \ - extern void perf_tpcounter_event(int, u64, u64); \ - u64 __addr = 0, __count = 1; \ - { assign; } \ - perf_tpcounter_event(event_##call.id, __addr, __count); \ -} \ +static void ftrace_profile_##call(proto); \ \ static int ftrace_profile_enable_##call(struct ftrace_event_call *event_call) \ { \ @@ -422,12 +396,6 @@ static void ftrace_profile_disable_##call(struct ftrace_event_call *event_call)\ #include TRACE_INCLUDE(TRACE_INCLUDE_FILE) -#undef TP_fast_assign -#define TP_fast_assign(args...) args - -#undef TP_perf_assign -#define TP_perf_assign(args...) - #endif /* @@ -647,5 +615,99 @@ __attribute__((section("_ftrace_events"))) event_##call = { \ #include TRACE_INCLUDE(TRACE_INCLUDE_FILE) +/* + * Define the insertion callback to profile events + * + * The job is very similar to ftrace_raw_event_ except that we don't + * insert in the ring buffer but in a perf counter. + * + * static void ftrace_profile_(proto) + * { + * struct ftrace_data_offsets_ __maybe_unused __data_offsets; + * struct ftrace_event_call *event_call = &event_; + * extern void perf_tpcounter_event(int, u64, u64, void *, int); + * struct ftrace_raw_##call *entry; + * u64 __addr = 0, __count = 1; + * unsigned long irq_flags; + * int __entry_size; + * int __data_size; + * int pc; + * + * local_save_flags(irq_flags); + * pc = preempt_count(); + * + * __data_size = ftrace_get_offsets_(&__data_offsets, args); + * __entry_size = __data_size + sizeof(*entry); + * + * do { + * char raw_data[__entry_size]; <- allocate our sample in the stack + * struct trace_entry *ent; + * + * entry = (struct ftrace_raw_ *)raw_data; + * ent = &entry->ent; + * tracing_generic_entry_update(ent, irq_flags, pc); + * ent->type = event_call->id; + * + * <- do some jobs with dynamic arrays + * + * <- affect our values + * + * perf_tpcounter_event(event_call->id, __addr, __count, entry, + * __entry_size); <- submit them to perf counter + * } while (0); + * + * } + */ + +#ifdef CONFIG_EVENT_PROFILE + +#undef __perf_addr +#define __perf_addr(a) __addr = (a) + +#undef __perf_count +#define __perf_count(c) __count = (c) + +#undef TRACE_EVENT +#define TRACE_EVENT(call, proto, args, tstruct, assign, print) \ +static void ftrace_profile_##call(proto) \ +{ \ + struct ftrace_data_offsets_##call __maybe_unused __data_offsets;\ + struct ftrace_event_call *event_call = &event_##call; \ + extern void perf_tpcounter_event(int, u64, u64, void *, int); \ + struct ftrace_raw_##call *entry; \ + u64 __addr = 0, __count = 1; \ + unsigned long irq_flags; \ + int __entry_size; \ + int __data_size; \ + int pc; \ + \ + local_save_flags(irq_flags); \ + pc = preempt_count(); \ + \ + __data_size = ftrace_get_offsets_##call(&__data_offsets, args); \ + __entry_size = ALIGN(__data_size + sizeof(*entry), sizeof(u64));\ + \ + do { \ + char raw_data[__entry_size]; \ + struct trace_entry *ent; \ + \ + entry = (struct ftrace_raw_##call *)raw_data; \ + ent = &entry->ent; \ + tracing_generic_entry_update(ent, irq_flags, pc); \ + ent->type = event_call->id; \ + \ + tstruct \ + \ + { assign; } \ + \ + perf_tpcounter_event(event_call->id, __addr, __count, entry,\ + __entry_size); \ + } while (0); \ + \ +} + +#include TRACE_INCLUDE(TRACE_INCLUDE_FILE) +#endif /* CONFIG_EVENT_PROFILE */ + #undef _TRACE_PROFILE_INIT diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index 52eb4b68d34..868102172aa 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -2646,6 +2646,7 @@ static void perf_counter_output(struct perf_counter *counter, int nmi, u64 counter; } group_entry; struct perf_callchain_entry *callchain = NULL; + struct perf_tracepoint_record *tp; int callchain_size = 0; u64 time; struct { @@ -2714,6 +2715,11 @@ static void perf_counter_output(struct perf_counter *counter, int nmi, header.size += sizeof(u64); } + if (sample_type & PERF_SAMPLE_TP_RECORD) { + tp = data->private; + header.size += tp->size; + } + ret = perf_output_begin(&handle, counter, header.size, nmi, 1); if (ret) return; @@ -2777,6 +2783,9 @@ static void perf_counter_output(struct perf_counter *counter, int nmi, } } + if (sample_type & PERF_SAMPLE_TP_RECORD) + perf_output_copy(&handle, tp->record, tp->size); + perf_output_end(&handle); } @@ -3703,11 +3712,18 @@ static const struct pmu perf_ops_task_clock = { }; #ifdef CONFIG_EVENT_PROFILE -void perf_tpcounter_event(int event_id, u64 addr, u64 count) +void perf_tpcounter_event(int event_id, u64 addr, u64 count, void *record, + int entry_size) { + struct perf_tracepoint_record tp = { + .size = entry_size, + .record = record, + }; + struct perf_sample_data data = { .regs = get_irq_regs(), .addr = addr, + .private = &tp, }; if (!data.regs) diff --git a/kernel/trace/trace.c b/kernel/trace/trace.c index 8930e39b9d8..c22b40f8f57 100644 --- a/kernel/trace/trace.c +++ b/kernel/trace/trace.c @@ -848,6 +848,7 @@ tracing_generic_entry_update(struct trace_entry *entry, unsigned long flags, ((pc & SOFTIRQ_MASK) ? TRACE_FLAG_SOFTIRQ : 0) | (need_resched() ? TRACE_FLAG_NEED_RESCHED : 0); } +EXPORT_SYMBOL_GPL(tracing_generic_entry_update); struct ring_buffer_event *trace_buffer_lock_reserve(struct trace_array *tr, int type, diff --git a/kernel/trace/trace.h b/kernel/trace/trace.h index 3548ae5cc78..8b9f4f6e955 100644 --- a/kernel/trace/trace.h +++ b/kernel/trace/trace.h @@ -438,10 +438,6 @@ struct trace_entry *tracing_get_trace_entry(struct trace_array *tr, struct trace_entry *trace_find_next_entry(struct trace_iterator *iter, int *ent_cpu, u64 *ent_ts); -void tracing_generic_entry_update(struct trace_entry *entry, - unsigned long flags, - int pc); - void default_wait_pipe(struct trace_iterator *iter); void poll_wait_pipe(struct trace_iterator *iter); diff --git a/tools/perf/builtin-record.c b/tools/perf/builtin-record.c index 6da09928130..90c98082af1 100644 --- a/tools/perf/builtin-record.c +++ b/tools/perf/builtin-record.c @@ -412,6 +412,7 @@ static void create_counter(int counter, int cpu, pid_t pid) if (call_graph) attr->sample_type |= PERF_SAMPLE_CALLCHAIN; + attr->mmap = track; attr->comm = track; attr->inherit = (cpu < 0) && inherit; -- GitLab From 923c42c19944da214d697e312a040384a0e33e78 Mon Sep 17 00:00:00 2001 From: Mike Galbraith Date: Wed, 22 Jul 2009 20:36:03 +0200 Subject: [PATCH 0940/1342] perf_counter tools: Fix/resurrect perf top annotation in a simple interactive form perf top used to have annotation support, but it has bitrotted and removed. This patch restores that: it allows the user to select any symbol in kernel space for source level annotation on the fly, switch between event counters and alter display variables. When symbol details are being displayed, stopping annotation reverts to normal. known keys: [d] select display delay. [e] select display entries (lines). [E] select annotation event counter. [f] select normal display count filter. [F] select annotation display count filter (percentage). [qQ] quit. [s] select annotation symbol and start annotation. [S] stop annotation, revert to normal display. [z] toggle event count zeroing. Sample: ------------------------------------------------------------------------------ PerfTop: 16719 irqs/sec kernel:78.7% [cache-misses/cache-references/instructions/cycles], (all, 4 CPUs) ------------------------------------------------------------------------------ Showing cache-misses for e1000_clean_rx_irq Events Pcnt (>=3%) 0 0.0% /* adjust length to remove Ethernet CRC */ 0 0.0% if (!(adapter->flags2 & FLAG2_CRC_STRIPPING)) 0 0.0% length -= 4; 436 5.0% f039: 41 f6 84 24 5c 29 00 testb $0x1,0x295c(%r12) 0 0.0% f089: 8b 4d 84 mov -0x7c(%rbp),%ecx 0 0.0% f08c: 48 83 ef 02 sub $0x2,%rdi 0 0.0% f090: 48 83 ee 02 sub $0x2,%rsi 811 9.3% f094: f3 a4 rep movsb %ds:(%rsi),%es:(%rdi) 0 0.0% 0 0.0% while (rx_desc->status & E1000_RXD_STAT_DD) { 0 0.0% f114: 41 f6 47 0c 01 testb $0x1,0xc(%r15) 7226 82.6% f119: 0f 85 24 fe ff ff jne ef43 Available events: 0 cache-misses 1 cache-references 2 instructions 3 cycles Enter details event counter: 2 ------------------------------------------------------------------------------ PerfTop: 15035 irqs/sec kernel:79.0% [cache-misses/cache-references/instructions/cycles], (all, 4 CPUs) ------------------------------------------------------------------------------ Showing instructions for e1000_clean_rx_irq Events Pcnt (>=3%) 0 0.0% int *work_done, int work_to_do) 0 0.0% { 175 0.9% eebf: 55 push %rbp 1898 9.8% eec0: 48 89 e5 mov %rsp,%rbp 0 0.0% 0 0.0% i = rx_ring->next_to_clean; 140 0.7% ef0a: 0f b7 41 1a movzwl 0x1a(%rcx),%eax 670 3.4% ef0e: 89 45 ac mov %eax,-0x54(%rbp) 0 0.0% { 0 0.0% memcpy(skb->data + offset, from, len); 91 0.5% f07b: 49 8b b6 e8 00 00 00 mov 0xe8(%r14),%rsi 1153 5.9% f082: 48 8b b8 e8 00 00 00 mov 0xe8(%rax),%rdi 42 0.2% f089: 8b 4d 84 mov -0x7c(%rbp),%ecx 14 0.1% f08c: 48 83 ef 02 sub $0x2,%rdi 0 0.0% f090: 48 83 ee 02 sub $0x2,%rsi 1618 8.3% f094: f3 a4 rep movsb %ds:(%rsi),%es:(%rdi) 0 0.0% 0 0.0% /* return some buffers to hardware, one at a time is too slow */ 0 0.0% if (cleaned_count >= E1000_RX_BUFFER_WRITE) { 867 4.5% f0e7: 83 7d b0 0f cmpl $0xf,-0x50(%rbp) 0 0.0% 0 0.0% while (rx_desc->status & E1000_RXD_STAT_DD) { 37 0.2% f114: 41 f6 47 0c 01 testb $0x1,0xc(%r15) 4047 20.8% f119: 0f 85 24 fe ff ff jne ef43 Signed-off-by: Mike Galbraith Signed-off-by: Peter Zijlstra Cc: Paul Mackerras Signed-off-by: Ingo Molnar --- tools/perf/builtin-top.c | 496 +++++++++++++++++++++++++++++++++++---- 1 file changed, 456 insertions(+), 40 deletions(-) diff --git a/tools/perf/builtin-top.c b/tools/perf/builtin-top.c index f139f1ab933..d58701346b1 100644 --- a/tools/perf/builtin-top.c +++ b/tools/perf/builtin-top.c @@ -31,6 +31,8 @@ #include #include +#include +#include #include #include @@ -54,7 +56,7 @@ static int system_wide = 0; static int default_interval = 100000; -static u64 count_filter = 5; +static int count_filter = 5; static int print_entries = 15; static int target_pid = -1; @@ -69,14 +71,26 @@ static int freq = 0; static int verbose = 0; static char *vmlinux = NULL; -static char *sym_filter; -static unsigned long filter_start; -static unsigned long filter_end; - static int delay_secs = 2; static int zero; static int dump_symtab; +/* + * Source + */ + +struct source_line { + u64 eip; + unsigned long count[MAX_COUNTERS]; + char *line; + struct source_line *next; +}; + +static char *sym_filter = NULL; +struct sym_entry *sym_filter_entry = NULL; +static int sym_pcnt_filter = 5; +static int sym_counter = 0; + /* * Symbols */ @@ -91,9 +105,237 @@ struct sym_entry { unsigned long snap_count; double weight; int skip; + struct source_line *source; + struct source_line *lines; + struct source_line **lines_tail; + pthread_mutex_t source_lock; }; -struct sym_entry *sym_filter_entry; +/* + * Source functions + */ + +static void parse_source(struct sym_entry *syme) +{ + struct symbol *sym; + struct module *module; + struct section *section = NULL; + FILE *file; + char command[PATH_MAX*2], *path = vmlinux; + u64 start, end, len; + + if (!syme) + return; + + if (syme->lines) { + pthread_mutex_lock(&syme->source_lock); + goto out_assign; + } + + sym = (struct symbol *)(syme + 1); + module = sym->module; + + if (module) + path = module->path; + if (!path) + return; + + start = sym->obj_start; + if (!start) + start = sym->start; + + if (module) { + section = module->sections->find_section(module->sections, ".text"); + if (section) + start -= section->vma; + } + + end = start + sym->end - sym->start + 1; + len = sym->end - sym->start; + + sprintf(command, "objdump --start-address=0x%016Lx --stop-address=0x%016Lx -dS %s", start, end, path); + + file = popen(command, "r"); + if (!file) + return; + + pthread_mutex_lock(&syme->source_lock); + syme->lines_tail = &syme->lines; + while (!feof(file)) { + struct source_line *src; + size_t dummy = 0; + char *c; + + src = malloc(sizeof(struct source_line)); + assert(src != NULL); + memset(src, 0, sizeof(struct source_line)); + + if (getline(&src->line, &dummy, file) < 0) + break; + if (!src->line) + break; + + c = strchr(src->line, '\n'); + if (c) + *c = 0; + + src->next = NULL; + *syme->lines_tail = src; + syme->lines_tail = &src->next; + + if (strlen(src->line)>8 && src->line[8] == ':') { + src->eip = strtoull(src->line, NULL, 16); + if (section) + src->eip += section->vma; + } + if (strlen(src->line)>8 && src->line[16] == ':') { + src->eip = strtoull(src->line, NULL, 16); + if (section) + src->eip += section->vma; + } + } + pclose(file); +out_assign: + sym_filter_entry = syme; + pthread_mutex_unlock(&syme->source_lock); +} + +static void __zero_source_counters(struct sym_entry *syme) +{ + int i; + struct source_line *line; + + line = syme->lines; + while (line) { + for (i = 0; i < nr_counters; i++) + line->count[i] = 0; + line = line->next; + } +} + +static void record_precise_ip(struct sym_entry *syme, int counter, u64 ip) +{ + struct source_line *line; + + if (syme != sym_filter_entry) + return; + + if (pthread_mutex_trylock(&syme->source_lock)) + return; + + if (!syme->source) + goto out_unlock; + + for (line = syme->lines; line; line = line->next) { + if (line->eip == ip) { + line->count[counter]++; + break; + } + if (line->eip > ip) + break; + } +out_unlock: + pthread_mutex_unlock(&syme->source_lock); +} + +static void lookup_sym_source(struct sym_entry *syme) +{ + struct symbol *symbol = (struct symbol *)(syme + 1); + struct source_line *line; + char pattern[PATH_MAX]; + char *idx; + + sprintf(pattern, "<%s>:", symbol->name); + + if (symbol->module) { + idx = strstr(pattern, "\t"); + if (idx) + *idx = 0; + } + + pthread_mutex_lock(&syme->source_lock); + for (line = syme->lines; line; line = line->next) { + if (strstr(line->line, pattern)) { + syme->source = line; + break; + } + } + pthread_mutex_unlock(&syme->source_lock); +} + +static void show_lines(struct source_line *queue, int count, int total) +{ + int i; + struct source_line *line; + + line = queue; + for (i = 0; i < count; i++) { + float pcnt = 100.0*(float)line->count[sym_counter]/(float)total; + + printf("%8li %4.1f%%\t%s\n", line->count[sym_counter], pcnt, line->line); + line = line->next; + } +} + +#define TRACE_COUNT 3 + +static void show_details(struct sym_entry *syme) +{ + struct symbol *symbol; + struct source_line *line; + struct source_line *line_queue = NULL; + int displayed = 0; + int line_queue_count = 0, total = 0, more = 0; + + if (!syme) + return; + + if (!syme->source) + lookup_sym_source(syme); + + if (!syme->source) + return; + + symbol = (struct symbol *)(syme + 1); + printf("Showing %s for %s\n", event_name(sym_counter), symbol->name); + printf(" Events Pcnt (>=%d%%)\n", sym_pcnt_filter); + + pthread_mutex_lock(&syme->source_lock); + line = syme->source; + while (line) { + total += line->count[sym_counter]; + line = line->next; + } + + line = syme->source; + while (line) { + float pcnt = 0.0; + + if (!line_queue_count) + line_queue = line; + line_queue_count++; + + if (line->count[sym_counter]) + pcnt = 100.0 * line->count[sym_counter] / (float)total; + if (pcnt >= (float)sym_pcnt_filter) { + if (displayed <= print_entries) + show_lines(line_queue, line_queue_count, total); + else more++; + displayed += line_queue_count; + line_queue_count = 0; + line_queue = NULL; + } else if (line_queue_count > TRACE_COUNT) { + line_queue = line_queue->next; + line_queue_count--; + } + + line->count[sym_counter] = zero ? 0 : line->count[sym_counter] * 7 / 8; + line = line->next; + } + pthread_mutex_unlock(&syme->source_lock); + if (more) + printf("%d lines not displayed, maybe increase display entries [e]\n", more); +} struct dso *kernel_dso; @@ -228,6 +470,11 @@ static void print_sym_table(void) printf("------------------------------------------------------------------------------\n\n"); + if (sym_filter_entry) { + show_details(sym_filter_entry); + return; + } + if (nr_counters == 1) printf(" samples pcnt"); else @@ -242,7 +489,7 @@ static void print_sym_table(void) struct symbol *sym = (struct symbol *)(syme + 1); double pcnt; - if (++printed > print_entries || syme->snap_count < count_filter) + if (++printed > print_entries || (int)syme->snap_count < count_filter) continue; pcnt = 100.0 - (100.0 * ((sum_ksamples - syme->snap_count) / @@ -261,19 +508,208 @@ static void print_sym_table(void) } } +static void prompt_integer(int *target, const char *msg) +{ + char *buf = malloc(0), *p; + size_t dummy = 0; + int tmp; + + fprintf(stdout, "\n%s: ", msg); + if (getline(&buf, &dummy, stdin) < 0) + return; + + p = strchr(buf, '\n'); + if (p) + *p = 0; + + p = buf; + while(*p) { + if (!isdigit(*p)) + goto out_free; + p++; + } + tmp = strtoul(buf, NULL, 10); + *target = tmp; +out_free: + free(buf); +} + +static void prompt_percent(int *target, const char *msg) +{ + int tmp = 0; + + prompt_integer(&tmp, msg); + if (tmp >= 0 && tmp <= 100) + *target = tmp; +} + +static void prompt_symbol(struct sym_entry **target, const char *msg) +{ + char *buf = malloc(0), *p; + struct sym_entry *syme = *target, *n, *found = NULL; + size_t dummy = 0; + + /* zero counters of active symbol */ + if (syme) { + pthread_mutex_lock(&syme->source_lock); + __zero_source_counters(syme); + *target = NULL; + pthread_mutex_unlock(&syme->source_lock); + } + + fprintf(stdout, "\n%s: ", msg); + if (getline(&buf, &dummy, stdin) < 0) + goto out_free; + + p = strchr(buf, '\n'); + if (p) + *p = 0; + + pthread_mutex_lock(&active_symbols_lock); + syme = list_entry(active_symbols.next, struct sym_entry, node); + pthread_mutex_unlock(&active_symbols_lock); + + list_for_each_entry_safe_from(syme, n, &active_symbols, node) { + struct symbol *sym = (struct symbol *)(syme + 1); + + if (!strcmp(buf, sym->name)) { + found = syme; + break; + } + } + + if (!found) { + fprintf(stderr, "Sorry, %s is not active.\n", sym_filter); + sleep(1); + return; + } else + parse_source(found); + +out_free: + free(buf); +} + +static void print_known_keys(void) +{ + fprintf(stdout, "\nknown keys:\n"); + fprintf(stdout, "\t[d] select display delay.\n"); + fprintf(stdout, "\t[e] select display entries (lines).\n"); + fprintf(stdout, "\t[E] select annotation event counter.\n"); + fprintf(stdout, "\t[f] select normal display count filter.\n"); + fprintf(stdout, "\t[F] select annotation display count filter (percentage).\n"); + fprintf(stdout, "\t[qQ] quit.\n"); + fprintf(stdout, "\t[s] select annotation symbol and start annotation.\n"); + fprintf(stdout, "\t[S] stop annotation, revert to normal display.\n"); + fprintf(stdout, "\t[z] toggle event count zeroing.\n"); +} + +static void handle_keypress(int c) +{ + int once = 0; +repeat: + switch (c) { + case 'd': + prompt_integer(&delay_secs, "Enter display delay"); + break; + case 'e': + prompt_integer(&print_entries, "Enter display entries (lines)"); + break; + case 'E': + if (nr_counters > 1) { + int i; + + fprintf(stderr, "\nAvailable events:"); + for (i = 0; i < nr_counters; i++) + fprintf(stderr, "\n\t%d %s", i, event_name(i)); + + prompt_integer(&sym_counter, "Enter details event counter"); + + if (sym_counter >= nr_counters) { + fprintf(stderr, "Sorry, no such event, using %s.\n", event_name(0)); + sym_counter = 0; + sleep(1); + } + } else sym_counter = 0; + break; + case 'f': + prompt_integer(&count_filter, "Enter display event count filter"); + break; + case 'F': + prompt_percent(&sym_pcnt_filter, "Enter details display event filter (percent)"); + break; + case 'q': + case 'Q': + printf("exiting.\n"); + exit(0); + case 's': + prompt_symbol(&sym_filter_entry, "Enter details symbol"); + break; + case 'S': + if (!sym_filter_entry) + break; + else { + struct sym_entry *syme = sym_filter_entry; + + pthread_mutex_lock(&syme->source_lock); + sym_filter_entry = NULL; + __zero_source_counters(syme); + pthread_mutex_unlock(&syme->source_lock); + } + break; + case 'z': + zero = ~zero; + break; + default: { + struct pollfd stdin_poll = { .fd = 0, .events = POLLIN }; + struct termios tc, save; + + if (!once) { + print_known_keys(); + once++; + } + + tcgetattr(0, &save); + tc = save; + tc.c_lflag &= ~(ICANON | ECHO); + tc.c_cc[VMIN] = 0; + tc.c_cc[VTIME] = 0; + tcsetattr(0, TCSANOW, &tc); + + poll(&stdin_poll, 1, -1); + c = getc(stdin); + + tcsetattr(0, TCSAFLUSH, &save); + goto repeat; + } + } +} + static void *display_thread(void *arg __used) { struct pollfd stdin_poll = { .fd = 0, .events = POLLIN }; - int delay_msecs = delay_secs * 1000; - - printf("PerfTop refresh period: %d seconds\n", delay_secs); + struct termios tc, save; + int delay_msecs, c; + + tcgetattr(0, &save); + tc = save; + tc.c_lflag &= ~(ICANON | ECHO); + tc.c_cc[VMIN] = 0; + tc.c_cc[VTIME] = 0; +repeat: + delay_msecs = delay_secs * 1000; + tcsetattr(0, TCSANOW, &tc); + /* trash return*/ + getc(stdin); do { print_sym_table(); } while (!poll(&stdin_poll, 1, delay_msecs) == 1); - printf("key pressed - exiting.\n"); - exit(0); + c = getc(stdin); + tcsetattr(0, TCSAFLUSH, &save); + + handle_keypress(c); + goto repeat; return NULL; } @@ -293,7 +729,6 @@ static const char *skip_symbols[] = { static int symbol_filter(struct dso *self, struct symbol *sym) { - static int filter_match; struct sym_entry *syme; const char *name = sym->name; int i; @@ -315,6 +750,10 @@ static int symbol_filter(struct dso *self, struct symbol *sym) return 1; syme = dso__sym_priv(self, sym); + pthread_mutex_init(&syme->source_lock, NULL); + if (!sym_filter_entry && sym_filter && !strcmp(name, sym_filter)) + sym_filter_entry = syme; + for (i = 0; skip_symbols[i]; i++) { if (!strcmp(skip_symbols[i], name)) { syme->skip = 1; @@ -322,29 +761,6 @@ static int symbol_filter(struct dso *self, struct symbol *sym) } } - if (filter_match == 1) { - filter_end = sym->start; - filter_match = -1; - if (filter_end - filter_start > 10000) { - fprintf(stderr, - "hm, too large filter symbol <%s> - skipping.\n", - sym_filter); - fprintf(stderr, "symbol filter start: %016lx\n", - filter_start); - fprintf(stderr, " end: %016lx\n", - filter_end); - filter_end = filter_start = 0; - sym_filter = NULL; - sleep(1); - } - } - - if (filter_match == 0 && sym_filter && !strcmp(name, sym_filter)) { - filter_match = 1; - filter_start = sym->start; - } - - return 0; } @@ -380,8 +796,6 @@ out_delete_dso: return -1; } -#define TRACE_COUNT 3 - /* * Binary search in the histogram table and record the hit: */ @@ -394,6 +808,7 @@ static void record_ip(u64 ip, int counter) if (!syme->skip) { syme->count[counter]++; + record_precise_ip(syme, counter, ip); pthread_mutex_lock(&active_symbols_lock); if (list_empty(&syme->node) || !syme->node.next) __list_insert_active_sym(syme); @@ -690,8 +1105,8 @@ static const struct option options[] = { "put the counters into a counter group"), OPT_BOOLEAN('i', "inherit", &inherit, "child tasks inherit counters"), - OPT_STRING('s', "sym-filter", &sym_filter, "pattern", - "only display symbols matchig this pattern"), + OPT_STRING('s', "sym-annotate", &sym_filter, "symbol name", + "symbol to annotate - requires -k option"), OPT_BOOLEAN('z', "zero", &zero, "zero history across updates"), OPT_INTEGER('F', "freq", &freq, @@ -734,6 +1149,7 @@ int cmd_top(int argc, const char **argv, const char *prefix __used) delay_secs = 1; parse_symbols(); + parse_source(sym_filter_entry); /* * Fill in the ones not specifically initialized via -c: -- GitLab From 46ab976443c6c566c8fe6fc72a6733a55ba9fbea Mon Sep 17 00:00:00 2001 From: Mike Galbraith Date: Fri, 24 Jul 2009 10:09:50 +0200 Subject: [PATCH 0941/1342] perf_counter tools: Allow perf top top users to switch between weighted and individual counter display Add [w]eighted hotkey. Pressing [w] toggles between displaying weighted total of all counters, and the counter selected via [E]vent select key. ------------------------------------------------------------------------------ PerfTop: 90395 irqs/sec kernel:16.1% [cache-misses/cache-references/instructions], (all, 4 CPUs) ------------------------------------------------------------------------------ weight samples pcnt RIP kernel function ______ _______ _____ ________________ _______________ 1275408.6 10881 - 5.3% - ffffffff81146f70 : copy_page_c 553683.4 43569 - 21.3% - ffffffff81146f20 : clear_page_c 74075.0 6768 - 3.3% - ffffffff81147190 : copy_user_generic_string 40602.9 7538 - 3.7% - ffffffff81284ba2 : _spin_lock 26882.1 965 - 0.5% - ffffffff8109d280 : file_ra_state_init [w] ------------------------------------------------------------------------------ PerfTop: 91221 irqs/sec kernel:14.5% [10000Hz cache-misses], (all, 4 CPUs) ------------------------------------------------------------------------------ weight samples pcnt RIP kernel function ______ _______ _____ ________________ _______________ 47320.00 - 22.3% - ffffffff81146f20 : clear_page_c 14261.00 - 6.7% - ffffffff810992f5 : __rmqueue 11046.00 - 5.2% - ffffffff81146f70 : copy_page_c 7842.00 - 3.7% - ffffffff81284ba2 : _spin_lock 7234.00 - 3.4% - ffffffff810aa1d6 : unmap_vmas Signed-off-by: Mike Galbraith Signed-off-by: Peter Zijlstra Signed-off-by: Ingo Molnar --- tools/perf/builtin-top.c | 24 +++++++++++++++++------- 1 file changed, 17 insertions(+), 7 deletions(-) diff --git a/tools/perf/builtin-top.c b/tools/perf/builtin-top.c index d58701346b1..4eef3465e83 100644 --- a/tools/perf/builtin-top.c +++ b/tools/perf/builtin-top.c @@ -90,6 +90,7 @@ static char *sym_filter = NULL; struct sym_entry *sym_filter_entry = NULL; static int sym_pcnt_filter = 5; static int sym_counter = 0; +static int display_weighted = -1; /* * Symbols @@ -354,6 +355,9 @@ static double sym_weight(const struct sym_entry *sym) double weight = sym->snap_count; int counter; + if (!display_weighted) + return weight; + for (counter = 1; counter < nr_counters-1; counter++) weight *= sym->count[counter]; @@ -401,7 +405,7 @@ static void rb_insert_active_sym(struct rb_root *tree, struct sym_entry *se) static void print_sym_table(void) { int printed = 0, j; - int counter; + int counter, snap = !display_weighted ? sym_counter : 0; float samples_per_sec = samples/delay_secs; float ksamples_per_sec = (samples-userspace_samples)/delay_secs; float sum_ksamples = 0.0; @@ -417,7 +421,7 @@ static void print_sym_table(void) pthread_mutex_unlock(&active_symbols_lock); list_for_each_entry_safe_from(syme, n, &active_symbols, node) { - syme->snap_count = syme->count[0]; + syme->snap_count = syme->count[snap]; if (syme->snap_count != 0) { syme->weight = sym_weight(syme); rb_insert_active_sym(&tmp, syme); @@ -437,7 +441,7 @@ static void print_sym_table(void) samples_per_sec, 100.0 - (100.0*((samples_per_sec-ksamples_per_sec)/samples_per_sec))); - if (nr_counters == 1) { + if (nr_counters == 1 || !display_weighted) { printf("%Ld", (u64)attrs[0].sample_period); if (freq) printf("Hz "); @@ -445,7 +449,9 @@ static void print_sym_table(void) printf(" "); } - for (counter = 0; counter < nr_counters; counter++) { + if (!display_weighted) + printf("%s", event_name(sym_counter)); + else for (counter = 0; counter < nr_counters; counter++) { if (counter) printf("/"); @@ -495,7 +501,7 @@ static void print_sym_table(void) pcnt = 100.0 - (100.0 * ((sum_ksamples - syme->snap_count) / sum_ksamples)); - if (nr_counters == 1) + if (nr_counters == 1 || !display_weighted) printf("%20.2f - ", syme->weight); else printf("%9.1f %10ld - ", syme->weight, syme->snap_count); @@ -594,13 +600,14 @@ static void print_known_keys(void) fprintf(stdout, "\nknown keys:\n"); fprintf(stdout, "\t[d] select display delay.\n"); fprintf(stdout, "\t[e] select display entries (lines).\n"); - fprintf(stdout, "\t[E] select annotation event counter.\n"); + fprintf(stdout, "\t[E] active event counter. \t(%s)\n", event_name(sym_counter)); fprintf(stdout, "\t[f] select normal display count filter.\n"); fprintf(stdout, "\t[F] select annotation display count filter (percentage).\n"); fprintf(stdout, "\t[qQ] quit.\n"); fprintf(stdout, "\t[s] select annotation symbol and start annotation.\n"); fprintf(stdout, "\t[S] stop annotation, revert to normal display.\n"); - fprintf(stdout, "\t[z] toggle event count zeroing.\n"); + fprintf(stdout, "\t[w] toggle display weighted/count[E]r. \t(%d)\n", display_weighted ? 1 : 0); + fprintf(stdout, "\t[z] toggle sample zeroing. \t(%d)\n", zero ? 1 : 0); } static void handle_keypress(int c) @@ -656,6 +663,9 @@ repeat: pthread_mutex_unlock(&syme->source_lock); } break; + case 'w': + display_weighted = ~display_weighted; + break; case 'z': zero = ~zero; break; -- GitLab From 7b4b6658e152ed4568cfff48175d93645df081d1 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Wed, 22 Jul 2009 09:29:32 +0200 Subject: [PATCH 0942/1342] perf_counter: Fix software counters for fast moving event sources Reimplement the software counters to deal with fast moving event sources (such as tracepoints). This means being able to generate multiple overflows from a single 'event' as well as support throttling. Signed-off-by: Peter Zijlstra Cc: Paul Mackerras Signed-off-by: Ingo Molnar --- kernel/perf_counter.c | 164 ++++++++++++++++++++++++------------------ 1 file changed, 94 insertions(+), 70 deletions(-) diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index 868102172aa..615440ab929 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -3344,87 +3344,81 @@ int perf_counter_overflow(struct perf_counter *counter, int nmi, * Generic software counter infrastructure */ -static void perf_swcounter_update(struct perf_counter *counter) +/* + * We directly increment counter->count and keep a second value in + * counter->hw.period_left to count intervals. This period counter + * is kept in the range [-sample_period, 0] so that we can use the + * sign as trigger. + */ + +static u64 perf_swcounter_set_period(struct perf_counter *counter) { struct hw_perf_counter *hwc = &counter->hw; - u64 prev, now; - s64 delta; + u64 period = hwc->last_period; + u64 nr, offset; + s64 old, val; + + hwc->last_period = hwc->sample_period; again: - prev = atomic64_read(&hwc->prev_count); - now = atomic64_read(&hwc->count); - if (atomic64_cmpxchg(&hwc->prev_count, prev, now) != prev) - goto again; + old = val = atomic64_read(&hwc->period_left); + if (val < 0) + return 0; - delta = now - prev; + nr = div64_u64(period + val, period); + offset = nr * period; + val -= offset; + if (atomic64_cmpxchg(&hwc->period_left, old, val) != old) + goto again; - atomic64_add(delta, &counter->count); - atomic64_sub(delta, &hwc->period_left); + return nr; } -static void perf_swcounter_set_period(struct perf_counter *counter) +static void perf_swcounter_overflow(struct perf_counter *counter, + int nmi, struct perf_sample_data *data) { struct hw_perf_counter *hwc = &counter->hw; - s64 left = atomic64_read(&hwc->period_left); - s64 period = hwc->sample_period; + u64 overflow; - if (unlikely(left <= -period)) { - left = period; - atomic64_set(&hwc->period_left, left); - hwc->last_period = period; - } + data->period = counter->hw.last_period; + overflow = perf_swcounter_set_period(counter); - if (unlikely(left <= 0)) { - left += period; - atomic64_add(period, &hwc->period_left); - hwc->last_period = period; - } + if (hwc->interrupts == MAX_INTERRUPTS) + return; - atomic64_set(&hwc->prev_count, -left); - atomic64_set(&hwc->count, -left); + for (; overflow; overflow--) { + if (perf_counter_overflow(counter, nmi, data)) { + /* + * We inhibit the overflow from happening when + * hwc->interrupts == MAX_INTERRUPTS. + */ + break; + } + } } -static enum hrtimer_restart perf_swcounter_hrtimer(struct hrtimer *hrtimer) +static void perf_swcounter_unthrottle(struct perf_counter *counter) { - enum hrtimer_restart ret = HRTIMER_RESTART; - struct perf_sample_data data; - struct perf_counter *counter; - u64 period; - - counter = container_of(hrtimer, struct perf_counter, hw.hrtimer); - counter->pmu->read(counter); - - data.addr = 0; - data.regs = get_irq_regs(); /* - * In case we exclude kernel IPs or are somehow not in interrupt - * context, provide the next best thing, the user IP. + * Nothing to do, we already reset hwc->interrupts. */ - if ((counter->attr.exclude_kernel || !data.regs) && - !counter->attr.exclude_user) - data.regs = task_pt_regs(current); +} - if (data.regs) { - if (perf_counter_overflow(counter, 0, &data)) - ret = HRTIMER_NORESTART; - } +static void perf_swcounter_add(struct perf_counter *counter, u64 nr, + int nmi, struct perf_sample_data *data) +{ + struct hw_perf_counter *hwc = &counter->hw; - period = max_t(u64, 10000, counter->hw.sample_period); - hrtimer_forward_now(hrtimer, ns_to_ktime(period)); + atomic64_add(nr, &counter->count); - return ret; -} + if (!hwc->sample_period) + return; -static void perf_swcounter_overflow(struct perf_counter *counter, - int nmi, struct perf_sample_data *data) -{ - data->period = counter->hw.last_period; + if (!data->regs) + return; - perf_swcounter_update(counter); - perf_swcounter_set_period(counter); - if (perf_counter_overflow(counter, nmi, data)) - /* soft-disable the counter */ - ; + if (!atomic64_add_negative(nr, &hwc->period_left)) + perf_swcounter_overflow(counter, nmi, data); } static int perf_swcounter_is_counting(struct perf_counter *counter) @@ -3488,15 +3482,6 @@ static int perf_swcounter_match(struct perf_counter *counter, return 1; } -static void perf_swcounter_add(struct perf_counter *counter, u64 nr, - int nmi, struct perf_sample_data *data) -{ - int neg = atomic64_add_negative(nr, &counter->hw.count); - - if (counter->hw.sample_period && !neg && data->regs) - perf_swcounter_overflow(counter, nmi, data); -} - static void perf_swcounter_ctx_event(struct perf_counter_context *ctx, enum perf_type_id type, u32 event, u64 nr, int nmi, @@ -3575,26 +3560,65 @@ void __perf_swcounter_event(u32 event, u64 nr, int nmi, static void perf_swcounter_read(struct perf_counter *counter) { - perf_swcounter_update(counter); } static int perf_swcounter_enable(struct perf_counter *counter) { - perf_swcounter_set_period(counter); + struct hw_perf_counter *hwc = &counter->hw; + + if (hwc->sample_period) { + hwc->last_period = hwc->sample_period; + perf_swcounter_set_period(counter); + } return 0; } static void perf_swcounter_disable(struct perf_counter *counter) { - perf_swcounter_update(counter); } static const struct pmu perf_ops_generic = { .enable = perf_swcounter_enable, .disable = perf_swcounter_disable, .read = perf_swcounter_read, + .unthrottle = perf_swcounter_unthrottle, }; +/* + * hrtimer based swcounter callback + */ + +static enum hrtimer_restart perf_swcounter_hrtimer(struct hrtimer *hrtimer) +{ + enum hrtimer_restart ret = HRTIMER_RESTART; + struct perf_sample_data data; + struct perf_counter *counter; + u64 period; + + counter = container_of(hrtimer, struct perf_counter, hw.hrtimer); + counter->pmu->read(counter); + + data.addr = 0; + data.regs = get_irq_regs(); + /* + * In case we exclude kernel IPs or are somehow not in interrupt + * context, provide the next best thing, the user IP. + */ + if ((counter->attr.exclude_kernel || !data.regs) && + !counter->attr.exclude_user) + data.regs = task_pt_regs(current); + + if (data.regs) { + if (perf_counter_overflow(counter, 0, &data)) + ret = HRTIMER_NORESTART; + } + + period = max_t(u64, 10000, counter->hw.sample_period); + hrtimer_forward_now(hrtimer, ns_to_ktime(period)); + + return ret; +} + /* * Software counter: cpu wall time clock */ -- GitLab From 091bd2e993fcb1094a23e36157285b62bc87afdf Mon Sep 17 00:00:00 2001 From: Mike Galbraith Date: Tue, 4 Aug 2009 10:21:23 +0200 Subject: [PATCH 0943/1342] perf top: Improve interactive key handling Pressing any key which is not currently mapped to functionality, based on startup command line options, displays currently mapped keys, and prompts for input. Pressing any unmapped key at the prompt returns the user to display mode with variables unchanged. eg, pressing ? etc displays currently available keys, the value of the variable associated with that key, and prompts. Pressing same again aborts input. Signed-off-by: Mike Galbraith Cc: Peter Zijlstra Signed-off-by: Ingo Molnar --- tools/perf/builtin-top.c | 108 ++++++++++++++++++++++++++------------- 1 file changed, 73 insertions(+), 35 deletions(-) diff --git a/tools/perf/builtin-top.c b/tools/perf/builtin-top.c index 4eef3465e83..7de28ce9ca2 100644 --- a/tools/perf/builtin-top.c +++ b/tools/perf/builtin-top.c @@ -595,25 +595,84 @@ out_free: free(buf); } -static void print_known_keys(void) +static void print_mapped_keys(void) { - fprintf(stdout, "\nknown keys:\n"); - fprintf(stdout, "\t[d] select display delay.\n"); - fprintf(stdout, "\t[e] select display entries (lines).\n"); - fprintf(stdout, "\t[E] active event counter. \t(%s)\n", event_name(sym_counter)); - fprintf(stdout, "\t[f] select normal display count filter.\n"); - fprintf(stdout, "\t[F] select annotation display count filter (percentage).\n"); - fprintf(stdout, "\t[qQ] quit.\n"); - fprintf(stdout, "\t[s] select annotation symbol and start annotation.\n"); - fprintf(stdout, "\t[S] stop annotation, revert to normal display.\n"); - fprintf(stdout, "\t[w] toggle display weighted/count[E]r. \t(%d)\n", display_weighted ? 1 : 0); + char *name = NULL; + + if (sym_filter_entry) { + struct symbol *sym = (struct symbol *)(sym_filter_entry+1); + name = sym->name; + } + + fprintf(stdout, "\nMapped keys:\n"); + fprintf(stdout, "\t[d] display refresh delay. \t(%d)\n", delay_secs); + fprintf(stdout, "\t[e] display entries (lines). \t(%d)\n", print_entries); + + if (nr_counters > 1) + fprintf(stdout, "\t[E] active event counter. \t(%s)\n", event_name(sym_counter)); + + fprintf(stdout, "\t[f] profile display filter (count). \t(%d)\n", count_filter); + + if (vmlinux) { + fprintf(stdout, "\t[F] annotate display filter (percent). \t(%d%%)\n", sym_pcnt_filter); + fprintf(stdout, "\t[s] annotate symbol. \t(%s)\n", name?: "NULL"); + fprintf(stdout, "\t[S] stop annotation.\n"); + } + + if (nr_counters > 1) + fprintf(stdout, "\t[w] toggle display weighted/count[E]r. \t(%d)\n", display_weighted ? 1 : 0); + fprintf(stdout, "\t[z] toggle sample zeroing. \t(%d)\n", zero ? 1 : 0); + fprintf(stdout, "\t[qQ] quit.\n"); +} + +static int key_mapped(int c) +{ + switch (c) { + case 'd': + case 'e': + case 'f': + case 'z': + case 'q': + case 'Q': + return 1; + case 'E': + case 'w': + return nr_counters > 1 ? 1 : 0; + case 'F': + case 's': + case 'S': + return vmlinux ? 1 : 0; + } + + return 0; } static void handle_keypress(int c) { - int once = 0; -repeat: + if (!key_mapped(c)) { + struct pollfd stdin_poll = { .fd = 0, .events = POLLIN }; + struct termios tc, save; + + print_mapped_keys(); + fprintf(stdout, "\nEnter selection, or unmapped key to continue: "); + fflush(stdout); + + tcgetattr(0, &save); + tc = save; + tc.c_lflag &= ~(ICANON | ECHO); + tc.c_cc[VMIN] = 0; + tc.c_cc[VTIME] = 0; + tcsetattr(0, TCSANOW, &tc); + + poll(&stdin_poll, 1, -1); + c = getc(stdin); + + tcsetattr(0, TCSAFLUSH, &save); + if (!key_mapped(c)) + return; + } + switch (c) { case 'd': prompt_integer(&delay_secs, "Enter display delay"); @@ -669,28 +728,6 @@ repeat: case 'z': zero = ~zero; break; - default: { - struct pollfd stdin_poll = { .fd = 0, .events = POLLIN }; - struct termios tc, save; - - if (!once) { - print_known_keys(); - once++; - } - - tcgetattr(0, &save); - tc = save; - tc.c_lflag &= ~(ICANON | ECHO); - tc.c_cc[VMIN] = 0; - tc.c_cc[VTIME] = 0; - tcsetattr(0, TCSANOW, &tc); - - poll(&stdin_poll, 1, -1); - c = getc(stdin); - - tcsetattr(0, TCSAFLUSH, &save); - goto repeat; - } } } @@ -705,6 +742,7 @@ static void *display_thread(void *arg __used) tc.c_lflag &= ~(ICANON | ECHO); tc.c_cc[VMIN] = 0; tc.c_cc[VTIME] = 0; + repeat: delay_msecs = delay_secs * 1000; tcsetattr(0, TCSANOW, &tc); -- GitLab From 836179834833272f89098c6d1e1b89e8e69797c2 Mon Sep 17 00:00:00 2001 From: Mike Galbraith Date: Tue, 4 Aug 2009 10:24:41 +0200 Subject: [PATCH 0944/1342] perf top: Update man page perf_counter tools: update perf top manual page to reflect current implementation. Signed-off-by: Mike Galbraith Cc: Peter Zijlstra Signed-off-by: Ingo Molnar --- tools/perf/Documentation/perf-top.txt | 112 +++++++++++++++++++++++--- 1 file changed, 99 insertions(+), 13 deletions(-) diff --git a/tools/perf/Documentation/perf-top.txt b/tools/perf/Documentation/perf-top.txt index 539d0128972..4a7d558dc30 100644 --- a/tools/perf/Documentation/perf-top.txt +++ b/tools/perf/Documentation/perf-top.txt @@ -3,36 +3,122 @@ perf-top(1) NAME ---- -perf-top - Run a command and profile it +perf-top - System profiling tool. SYNOPSIS -------- [verse] -'perf top' [-e | --event=EVENT] [-l] [-a] +'perf top' [-e | --event=EVENT] [] DESCRIPTION ----------- -This command runs a command and gathers a performance counter profile -from it. +This command generates and displays a performance counter profile in realtime. OPTIONS ------- -...:: - Any command you can specify in a shell. +-a:: +--all-cpus:: + System-wide collection. (default) + +-c :: +--count=:: + Event period to sample. + +-C :: +--CPU=:: + CPU to profile. + +-d :: +--delay=:: + Number of seconds to delay between refreshes. --e:: ---event=:: +-e :: +--event=:: Select the PMU event. Selection can be a symbolic event name (use 'perf list' to list all events) or a raw PMU event (eventsel+umask) in the form of rNNN where NNN is a - hexadecimal event descriptor. + hexadecimal event descriptor. --a:: - system-wide collection +-E :: +--entries=:: + Display this many functions. + +-f :: +--count-filter=:: + Only display functions with more events than this. + +-F :: +--freq=:: + Profile at this frequency. + +-i:: +--inherit:: + Child tasks inherit counters, only makes sens with -p option. + +-k :: +--vmlinux=:: + Path to vmlinux. Required for annotation functionality. + +-m :: +--mmap-pages=:: + Number of mmapped data pages. + +-p :: +--pid=:: + Profile events on existing pid. + +-r :: +--realtime=:: + Collect data with this RT SCHED_FIFO priority. + +-s :: +--sym-annotate=:: + Annotate this symbol. Requires -k option. + +-v:: +--verbose:: + Be more verbose (show counter open errors, etc). + +-z:: +--zero:: + Zero history across display updates. + +INTERACTIVE PROMPTING KEYS +-------------------------- + +[d]:: + Display refresh delay. + +[e]:: + Number of entries to display. + +[E]:: + Event to display when multiple counters are active. + +[f]:: + Profile display filter (>= hit count). + +[F]:: + Annotation display filter (>= % of total). + +[s]:: + Annotate symbol. + +[S]:: + Stop annotation, return to full profile display. + +[w]:: + Toggle between weighted sum and individual count[E]r profile. + +[z]:: + Toggle event count zeroing across display updates. + +[qQ]:: + Quit. + +Pressing any unmapped key displays a menu, and prompts for input. --l:: - scale counter values SEE ALSO -------- -- GitLab From 1953287bfe8afcbbd235bd6c42c9df06d52438dc Mon Sep 17 00:00:00 2001 From: Frederic Weisbecker Date: Fri, 7 Aug 2009 07:11:05 +0200 Subject: [PATCH 0945/1342] perf tools: Fix call-chain cumul hit based sub-total (fractal mode) The callchain fractal mode builds each new total hits in a new branch of profiling by using the parent's hits of the current branch plus the hits of the children. This is wrong, the total hits of a branch should be made of the sum of every children hits, we must ignore the parent hits in this scope. This patch also fixes another mistake with the hit counting. Now the rates are correct. Signed-off-by: Frederic Weisbecker Cc: Frederic Weisbecker Cc: Peter Zijlstra Cc: Arnaldo Carvalho de Melo Cc: Mike Galbraith Cc: Pekka Enberg Signed-off-by: Ingo Molnar --- tools/perf/builtin-report.c | 4 ++-- tools/perf/util/callchain.c | 27 ++++++++++++++++----------- tools/perf/util/callchain.h | 7 ++++++- 3 files changed, 24 insertions(+), 14 deletions(-) diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c index 8cb58d68a00..da402e18656 100644 --- a/tools/perf/builtin-report.c +++ b/tools/perf/builtin-report.c @@ -901,7 +901,7 @@ callchain__fprintf_graph(FILE *fp, struct callchain_node *self, int i; if (callchain_param.mode == CHAIN_GRAPH_REL) - new_total = self->cumul_hit; + new_total = self->children_hit; else new_total = total_samples; @@ -930,7 +930,7 @@ callchain__fprintf_graph(FILE *fp, struct callchain_node *self, ret += ipchain__fprintf_graph(fp, chain, depth, new_depth_mask, i++, new_total, - child->cumul_hit); + cumul_hits(child)); } ret += callchain__fprintf_graph(fp, child, new_total, depth + 1, diff --git a/tools/perf/util/callchain.c b/tools/perf/util/callchain.c index 9d3c8141b8c..98c5627f327 100644 --- a/tools/perf/util/callchain.c +++ b/tools/perf/util/callchain.c @@ -26,10 +26,14 @@ rb_insert_callchain(struct rb_root *root, struct callchain_node *chain, struct rb_node **p = &root->rb_node; struct rb_node *parent = NULL; struct callchain_node *rnode; + u64 chain_cumul = cumul_hits(chain); while (*p) { + u64 rnode_cumul; + parent = *p; rnode = rb_entry(parent, struct callchain_node, rb_node); + rnode_cumul = cumul_hits(rnode); switch (mode) { case CHAIN_FLAT: @@ -40,7 +44,7 @@ rb_insert_callchain(struct rb_root *root, struct callchain_node *chain, break; case CHAIN_GRAPH_ABS: /* Falldown */ case CHAIN_GRAPH_REL: - if (rnode->cumul_hit < chain->cumul_hit) + if (rnode_cumul < chain_cumul) p = &(*p)->rb_left; else p = &(*p)->rb_right; @@ -87,7 +91,7 @@ static void __sort_chain_graph_abs(struct callchain_node *node, chain_for_each_child(child, node) { __sort_chain_graph_abs(child, min_hit); - if (child->cumul_hit >= min_hit) + if (cumul_hits(child) >= min_hit) rb_insert_callchain(&node->rb_root, child, CHAIN_GRAPH_ABS); } @@ -108,11 +112,11 @@ static void __sort_chain_graph_rel(struct callchain_node *node, u64 min_hit; node->rb_root = RB_ROOT; - min_hit = node->cumul_hit * min_percent / 100.0; + min_hit = node->children_hit * min_percent / 100.0; chain_for_each_child(child, node) { __sort_chain_graph_rel(child, min_percent); - if (child->cumul_hit >= min_hit) + if (cumul_hits(child) >= min_hit) rb_insert_callchain(&node->rb_root, child, CHAIN_GRAPH_REL); } @@ -211,7 +215,8 @@ add_child(struct callchain_node *parent, struct ip_callchain *chain, new = create_child(parent, false); fill_node(new, chain, start, syms); - new->cumul_hit = new->hit = 1; + new->children_hit = 0; + new->hit = 1; } /* @@ -241,7 +246,8 @@ split_add_child(struct callchain_node *parent, struct ip_callchain *chain, /* split the hits */ new->hit = parent->hit; - new->cumul_hit = parent->cumul_hit; + new->children_hit = parent->children_hit; + parent->children_hit = cumul_hits(new); new->val_nr = parent->val_nr - idx_local; parent->val_nr = idx_local; @@ -249,6 +255,7 @@ split_add_child(struct callchain_node *parent, struct ip_callchain *chain, if (idx_total < chain->nr) { parent->hit = 0; add_child(parent, chain, idx_total, syms); + parent->children_hit++; } else { parent->hit = 1; } @@ -269,13 +276,13 @@ __append_chain_children(struct callchain_node *root, struct ip_callchain *chain, unsigned int ret = __append_chain(rnode, chain, start, syms); if (!ret) - goto cumul; + goto inc_children_hit; } /* nothing in children, add to the current node */ add_child(root, chain, start, syms); -cumul: - root->cumul_hit++; +inc_children_hit: + root->children_hit++; } static int @@ -317,8 +324,6 @@ __append_chain(struct callchain_node *root, struct ip_callchain *chain, /* we match 100% of the path, increment the hit */ if (i - start == root->val_nr && i == chain->nr) { root->hit++; - root->cumul_hit++; - return 0; } diff --git a/tools/perf/util/callchain.h b/tools/perf/util/callchain.h index 7812122bea1..b2d128e07c8 100644 --- a/tools/perf/util/callchain.h +++ b/tools/perf/util/callchain.h @@ -21,7 +21,7 @@ struct callchain_node { struct rb_root rb_root; /* sorted tree of children */ unsigned int val_nr; u64 hit; - u64 cumul_hit; /* hit + hits of children */ + u64 children_hit; }; struct callchain_param; @@ -48,6 +48,11 @@ static inline void callchain_init(struct callchain_node *node) INIT_LIST_HEAD(&node->val); } +static inline u64 cumul_hits(struct callchain_node *node) +{ + return node->hit + node->children_hit; +} + int register_callchain_param(struct callchain_param *param); void append_chain(struct callchain_node *root, struct ip_callchain *chain, struct symbol **syms); -- GitLab From 1c222bce7dd0cb9578b4c5cd3874a74f1db497c3 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Thu, 6 Aug 2009 20:57:41 +0200 Subject: [PATCH 0946/1342] perf tools: Fix multi-counter stat bug caused by incorrect reading of perf.data file header Brice Goglin reported that only the first result from a multi-counter perf record --stat run is accurate, the rest looks bogus. A silly mistake made us re-read the first attribute for every recorded attribute. Reported-by: Brice Goglin Signed-off-by: Peter Zijlstra Tested-by: Brice Goglin Cc: paulus@samba.org Signed-off-by: Ingo Molnar --- tools/perf/util/header.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/tools/perf/util/header.c b/tools/perf/util/header.c index 450384b3bbe..95a44bcfc2d 100644 --- a/tools/perf/util/header.c +++ b/tools/perf/util/header.c @@ -213,9 +213,10 @@ struct perf_header *perf_header__read(int fd) for (i = 0; i < nr_attrs; i++) { struct perf_header_attr *attr; - off_t tmp = lseek(fd, 0, SEEK_CUR); + off_t tmp; do_read(fd, &f_attr, sizeof(f_attr)); + tmp = lseek(fd, 0, SEEK_CUR); attr = perf_header_attr__new(&f_attr.attr); -- GitLab From 8f18aec535b5ca513dd13b531730177d35175ffa Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Thu, 6 Aug 2009 19:40:28 +0200 Subject: [PATCH 0947/1342] perf report: Fix per task mult-counter stat reporting Brice Goglin reported: > I can easily sort them by thread id, but I don't know how to match > my 4 events with each group of 4 lines. Also report the counter id and the time running/enabled stats (in case the counter got time-shared). Reported-by: Brice Goglin Signed-off-by: Peter Zijlstra Tested-by: Brice Goglin Signed-off-by: Ingo Molnar --- tools/perf/builtin-report.c | 31 +++++++++++++++++++++++++++---- tools/perf/util/parse-events.c | 8 +++++++- tools/perf/util/parse-events.h | 1 + 3 files changed, 35 insertions(+), 5 deletions(-) diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c index da402e18656..84205462e07 100644 --- a/tools/perf/builtin-report.c +++ b/tools/perf/builtin-report.c @@ -112,7 +112,9 @@ struct read_event { struct perf_event_header header; u32 pid,tid; u64 value; - u64 format[3]; + u64 time_enabled; + u64 time_running; + u64 id; }; typedef union event_union { @@ -1690,14 +1692,37 @@ static void trace_event(event_t *event) dprintf(".\n"); } +static struct perf_header *header; + +static struct perf_counter_attr *perf_header__find_attr(u64 id) +{ + int i; + + for (i = 0; i < header->attrs; i++) { + struct perf_header_attr *attr = header->attr[i]; + int j; + + for (j = 0; j < attr->ids; j++) { + if (attr->id[j] == id) + return &attr->attr; + } + } + + return NULL; +} + static int process_read_event(event_t *event, unsigned long offset, unsigned long head) { - dprintf("%p [%p]: PERF_EVENT_READ: %d %d %Lu\n", + struct perf_counter_attr *attr = perf_header__find_attr(event->read.id); + + dprintf("%p [%p]: PERF_EVENT_READ: %d %d %s %Lu\n", (void *)(offset + head), (void *)(long)(event->header.size), event->read.pid, event->read.tid, + attr ? __event_name(attr->type, attr->config) + : "FAIL", event->read.value); return 0; @@ -1743,8 +1768,6 @@ process_event(event_t *event, unsigned long offset, unsigned long head) return 0; } -static struct perf_header *header; - static u64 perf_header__sample_type(void) { u64 sample_type = 0; diff --git a/tools/perf/util/parse-events.c b/tools/perf/util/parse-events.c index 7bdad8df22a..f77407b5832 100644 --- a/tools/perf/util/parse-events.c +++ b/tools/perf/util/parse-events.c @@ -223,9 +223,15 @@ char *event_name(int counter) { u64 config = attrs[counter].config; int type = attrs[counter].type; + + return __event_name(type, config); +} + +char *__event_name(int type, u64 config) +{ static char buf[32]; - if (attrs[counter].type == PERF_TYPE_RAW) { + if (type == PERF_TYPE_RAW) { sprintf(buf, "raw 0x%llx", config); return buf; } diff --git a/tools/perf/util/parse-events.h b/tools/perf/util/parse-events.h index 1ea5d09b6eb..192a962e3a0 100644 --- a/tools/perf/util/parse-events.h +++ b/tools/perf/util/parse-events.h @@ -10,6 +10,7 @@ extern int nr_counters; extern struct perf_counter_attr attrs[MAX_COUNTERS]; extern char *event_name(int ctr); +extern char *__event_name(int type, u64 config); extern int parse_events(const struct option *opt, const char *str, int unset); -- GitLab From 94cb9e385d5b4d55a5ae389baa10ad2835ea39bb Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Thu, 6 Aug 2009 14:43:17 -0300 Subject: [PATCH 0948/1342] perf report: Add debug help for the finding of symbol bugs - show the symtab origin (DSO, build-id, kernel, etc) Used with perf report --verbose: [acme@doppio linux-2.6-tip]$ perf report -v | head -16 5.17% firefox /usr/lib64/xulrunner-1.9.1/libxul.so 0x00000000005d8eee f [.] imgContainer::DrawFrameTo(gfxIImageFrame*, gfxIImageFrame*, nsRect&) 2.56% firefox /lib64/libpthread-2.10.1.so 0x0000000000008e02 d [.] __pthread_mutex_lock_internal 1.94% firefox /usr/lib64/xulrunner-1.9.1/libxul.so 0x0000000000d0af8f f [.] SearchTable 1.75% firefox [kernel] 0xffffffffff60013b k [.] vread_hpet 1.63% firefox /lib64/libpthread-2.10.1.so 0x000000000000a404 d [.] __pthread_mutex_unlock 1.47% firefox /usr/lib64/xulrunner-1.9.1/libmozjs.so 0x00000000000482ea f [.] js_Interpret 1.42% firefox /usr/lib64/xulrunner-1.9.1/libmozjs.so 0x000000000003eda3 f [.] JS_CallTracer 1.24% firefox [kernel] 0xffffffff8102ca4a k [k] read_hpet 1.16% firefox [kernel] 0xffffffff810f3dd4 k [k] fget_light 1.11% firefox /usr/lib64/xulrunner-1.9.1/libmozjs.so 0x00000000000567ff f [.] js_TraceObject 0.98% firefox /usr/lib64/firefox-3.5.2/firefox 0x000000000000dd23 b [.] arena_ralloc [acme@doppio linux-2.6-tip]$ The new field is just after the symbol address. To help in figuring out symbol resolution bugs. Signed-off-by: Arnaldo Carvalho de Melo Acked-by: Peter Zijlstra Signed-off-by: Ingo Molnar --- tools/perf/builtin-report.c | 3 +- tools/perf/util/symbol.c | 57 ++++++++++++++++++++++++++++++------- tools/perf/util/symbol.h | 2 ++ 3 files changed, 50 insertions(+), 12 deletions(-) diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c index 84205462e07..a5e2f8df411 100644 --- a/tools/perf/builtin-report.c +++ b/tools/perf/builtin-report.c @@ -700,7 +700,8 @@ sort__sym_print(FILE *fp, struct hist_entry *self, unsigned int width __used) size_t ret = 0; if (verbose) - ret += repsep_fprintf(fp, "%#018llx ", (u64)self->ip); + ret += repsep_fprintf(fp, "%#018llx %c ", (u64)self->ip, + dso__symtab_origin(self->dso)); ret += repsep_fprintf(fp, "[%c] ", self->level); if (self->sym) { diff --git a/tools/perf/util/symbol.c b/tools/perf/util/symbol.c index 16ddca20294..f1dcede1430 100644 --- a/tools/perf/util/symbol.c +++ b/tools/perf/util/symbol.c @@ -24,6 +24,16 @@ const char *sym_hist_filter; #define DMGL_ANSI (1 << 1) /* Include const, volatile, etc */ #endif +enum dso_origin { + DSO__ORIG_KERNEL = 0, + DSO__ORIG_JAVA_JIT, + DSO__ORIG_FEDORA, + DSO__ORIG_UBUNTU, + DSO__ORIG_BUILDID, + DSO__ORIG_DSO, + DSO__ORIG_NOT_FOUND, +}; + static struct symbol *symbol__new(u64 start, u64 len, const char *name, unsigned int priv_size, u64 obj_start, int verbose) @@ -81,6 +91,7 @@ struct dso *dso__new(const char *name, unsigned int sym_priv_size) self->sym_priv_size = sym_priv_size; self->find_symbol = dso__find_symbol; self->slen_calculated = 0; + self->origin = DSO__ORIG_NOT_FOUND; } return self; @@ -710,7 +721,7 @@ static char *dso__read_build_id(struct dso *self, int verbose) ++raw; bid += 2; } - if (verbose) + if (verbose >= 2) printf("%s(%s): %s\n", __func__, self->name, build_id); out_elf_end: elf_end(elf); @@ -720,11 +731,26 @@ out: return build_id; } +char dso__symtab_origin(const struct dso *self) +{ + static const char origin[] = { + [DSO__ORIG_KERNEL] = 'k', + [DSO__ORIG_JAVA_JIT] = 'j', + [DSO__ORIG_FEDORA] = 'f', + [DSO__ORIG_UBUNTU] = 'u', + [DSO__ORIG_BUILDID] = 'b', + [DSO__ORIG_DSO] = 'd', + }; + + if (self == NULL || self->origin == DSO__ORIG_NOT_FOUND) + return '!'; + return origin[self->origin]; +} + int dso__load(struct dso *self, symbol_filter_t filter, int verbose) { int size = PATH_MAX; char *name = malloc(size), *build_id = NULL; - int variant = 0; int ret = -1; int fd; @@ -733,19 +759,26 @@ int dso__load(struct dso *self, symbol_filter_t filter, int verbose) self->adjust_symbols = 0; - if (strncmp(self->name, "/tmp/perf-", 10) == 0) - return dso__load_perf_map(self, filter, verbose); + if (strncmp(self->name, "/tmp/perf-", 10) == 0) { + ret = dso__load_perf_map(self, filter, verbose); + self->origin = ret > 0 ? DSO__ORIG_JAVA_JIT : + DSO__ORIG_NOT_FOUND; + return ret; + } + + self->origin = DSO__ORIG_FEDORA - 1; more: do { - switch (variant) { - case 0: /* Fedora */ + self->origin++; + switch (self->origin) { + case DSO__ORIG_FEDORA: snprintf(name, size, "/usr/lib/debug%s.debug", self->name); break; - case 1: /* Ubuntu */ + case DSO__ORIG_UBUNTU: snprintf(name, size, "/usr/lib/debug%s", self->name); break; - case 2: + case DSO__ORIG_BUILDID: build_id = dso__read_build_id(self, verbose); if (build_id != NULL) { snprintf(name, size, @@ -754,16 +787,15 @@ more: free(build_id); break; } - variant++; + self->origin++; /* Fall thru */ - case 3: /* Sane people */ + case DSO__ORIG_DSO: snprintf(name, size, "%s", self->name); break; default: goto out; } - variant++; fd = open(name, O_RDONLY); } while (fd < 0); @@ -899,6 +931,9 @@ int dso__load_kernel(struct dso *self, const char *vmlinux, if (err <= 0) err = dso__load_kallsyms(self, filter, verbose); + if (err > 0) + self->origin = DSO__ORIG_KERNEL; + return err; } diff --git a/tools/perf/util/symbol.h b/tools/perf/util/symbol.h index 2f92b21c712..1e003ec2f4b 100644 --- a/tools/perf/util/symbol.h +++ b/tools/perf/util/symbol.h @@ -26,6 +26,7 @@ struct dso { unsigned int sym_priv_size; unsigned char adjust_symbols; unsigned char slen_calculated; + unsigned char origin; char name[0]; }; @@ -49,6 +50,7 @@ int dso__load_modules(struct dso *self, symbol_filter_t filter, int verbose); int dso__load(struct dso *self, symbol_filter_t filter, int verbose); size_t dso__fprintf(struct dso *self, FILE *fp); +char dso__symtab_origin(const struct dso *self); void symbol__init(void); #endif /* _PERF_SYMBOL_ */ -- GitLab From b26bc5a7f81474937e427b0c855eabee5ad56f89 Mon Sep 17 00:00:00 2001 From: Brice Goglin Date: Fri, 7 Aug 2009 10:18:39 +0200 Subject: [PATCH 0949/1342] perf stat: Fix tool option consistency: rename -S/--scale to -c/--scale We want to use a coherent flag for -S/--stat across all tools, so free up -S in perf stat. Signed-off-by: Brice Goglin Cc: Peter Zijlstra Cc: paulus@samba.org Signed-off-by: Ingo Molnar --- tools/perf/Documentation/perf-stat.txt | 2 +- tools/perf/builtin-stat.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/tools/perf/Documentation/perf-stat.txt b/tools/perf/Documentation/perf-stat.txt index 0d74346d21a..484080dd5b6 100644 --- a/tools/perf/Documentation/perf-stat.txt +++ b/tools/perf/Documentation/perf-stat.txt @@ -40,7 +40,7 @@ OPTIONS -a:: system-wide collection --S:: +-c:: scale counter values EXAMPLES diff --git a/tools/perf/builtin-stat.c b/tools/perf/builtin-stat.c index f9510eeeb6c..b4b06c7903e 100644 --- a/tools/perf/builtin-stat.c +++ b/tools/perf/builtin-stat.c @@ -496,7 +496,7 @@ static const struct option options[] = { "stat events on existing pid"), OPT_BOOLEAN('a', "all-cpus", &system_wide, "system-wide collection from all CPUs"), - OPT_BOOLEAN('S', "scale", &scale, + OPT_BOOLEAN('c', "scale", &scale, "scale/normalize counters"), OPT_BOOLEAN('v', "verbose", &verbose, "be more verbose (show counter open errors, etc)"), -- GitLab From f36a1a133a947973efb8e6a1fbdcc23e4a011437 Mon Sep 17 00:00:00 2001 From: Paul Mackerras Date: Fri, 7 Aug 2009 16:59:45 +1000 Subject: [PATCH 0950/1342] perf_counter/powerpc: Fix oops on cpus without perf_counter hardware support If we have the powerpc perf_counter backend compiled in, but the cpu we are running on is one where we don't support the PMU, we currently oops in hw_perf_group_sched_in if we try to use any counters, because ppmu is NULL in that case, and we unconditionally dereference ppmu. This fixes the problem by adding a check if ppmu is NULL at the beginning of hw_perf_group_sched_in, and also at the beginning of the other functions that get called from the perf_counter core, i.e. hw_perf_disable, hw_perf_enable, and hw_perf_counter_setup. Signed-off-by: Paul Mackerras Cc: Peter Zijlstra Cc: benh@kernel.crashing.org Signed-off-by: Ingo Molnar --- arch/powerpc/kernel/perf_counter.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/powerpc/kernel/perf_counter.c b/arch/powerpc/kernel/perf_counter.c index 809fdf94b95..70e1f57f7dd 100644 --- a/arch/powerpc/kernel/perf_counter.c +++ b/arch/powerpc/kernel/perf_counter.c @@ -518,6 +518,8 @@ void hw_perf_disable(void) struct cpu_hw_counters *cpuhw; unsigned long flags; + if (!ppmu) + return; local_irq_save(flags); cpuhw = &__get_cpu_var(cpu_hw_counters); @@ -572,6 +574,8 @@ void hw_perf_enable(void) int n_lim; int idx; + if (!ppmu) + return; local_irq_save(flags); cpuhw = &__get_cpu_var(cpu_hw_counters); if (!cpuhw->disabled) { @@ -737,6 +741,8 @@ int hw_perf_group_sched_in(struct perf_counter *group_leader, long i, n, n0; struct perf_counter *sub; + if (!ppmu) + return 0; cpuhw = &__get_cpu_var(cpu_hw_counters); n0 = cpuhw->n_counters; n = collect_events(group_leader, ppmu->n_counter - n0, @@ -1281,6 +1287,8 @@ void hw_perf_counter_setup(int cpu) { struct cpu_hw_counters *cpuhw = &per_cpu(cpu_hw_counters, cpu); + if (!ppmu) + return; memset(cpuhw, 0, sizeof(*cpuhw)); cpuhw->mmcr[0] = MMCR0_FC; } -- GitLab From ae07b63f4b6728e1f98aa5c5416cfc1280f59f51 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Thu, 6 Aug 2009 16:48:54 +0200 Subject: [PATCH 0951/1342] perf list: Fix the output to not include tracepoints without an id Stop perf list from displaying tracepoints without an id file, those are special tracepoints that are not interfaced to perfcounters so listing them is erroneous and passing them as events will produce no output. Signed-off-by: Peter Zijlstra Acked-by: Jason Baron Cc: Steven Rostedt Cc: Chris Mason Signed-off-by: Ingo Molnar --- tools/perf/util/parse-events.c | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-) diff --git a/tools/perf/util/parse-events.c b/tools/perf/util/parse-events.c index f77407b5832..4858d83b3b6 100644 --- a/tools/perf/util/parse-events.c +++ b/tools/perf/util/parse-events.c @@ -121,13 +121,29 @@ static unsigned long hw_cache_stat[C(MAX)] = { (strcmp(sys_dirent.d_name, ".")) && \ (strcmp(sys_dirent.d_name, ".."))) +static int tp_event_has_id(struct dirent *sys_dir, struct dirent *evt_dir) +{ + char evt_path[MAXPATHLEN]; + int fd; + + snprintf(evt_path, MAXPATHLEN, "%s/%s/%s/id", debugfs_path, + sys_dir->d_name, evt_dir->d_name); + fd = open(evt_path, O_RDONLY); + if (fd < 0) + return -EINVAL; + close(fd); + + return 0; +} + #define for_each_event(sys_dirent, evt_dir, evt_dirent, evt_next, file, st) \ while (!readdir_r(evt_dir, &evt_dirent, &evt_next) && evt_next) \ if (snprintf(file, MAXPATHLEN, "%s/%s/%s", debugfs_path, \ sys_dirent.d_name, evt_dirent.d_name) && \ (!stat(file, &st)) && (S_ISDIR(st.st_mode)) && \ (strcmp(evt_dirent.d_name, ".")) && \ - (strcmp(evt_dirent.d_name, ".."))) + (strcmp(evt_dirent.d_name, "..")) && \ + (!tp_event_has_id(&sys_dirent, &evt_dirent))) #define MAX_EVENT_LENGTH 30 -- GitLab From 7eac7e9e726c1b136bd7e0ad6671ce315f48bb18 Mon Sep 17 00:00:00 2001 From: Pierre Habouzit Date: Fri, 7 Aug 2009 14:16:00 +0200 Subject: [PATCH 0952/1342] perf util: Fix do_read() to fail on EOF instead of busy-looping While toying with perf, I've noticed that perf record can easily enter a busy loop when doing something as silly as: $ perf record -A ls Yeah, do_read here really wants to read a known size, not being able to should die(), not busy-loop ;) That was the cause for the bug. Signed-off-by: Pierre Habouzit Acked-by: Peter Zijlstra Cc: Paul Mackerras Signed-off-by: Ingo Molnar --- tools/perf/util/header.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/tools/perf/util/header.c b/tools/perf/util/header.c index 95a44bcfc2d..b92a457ca32 100644 --- a/tools/perf/util/header.c +++ b/tools/perf/util/header.c @@ -185,6 +185,8 @@ static void do_read(int fd, void *buf, size_t size) if (ret < 0) die("failed to read"); + if (ret == 0) + die("failed to read: missing data"); size -= ret; buf += ret; -- GitLab From 266e0e219888420a1a7cafc82e82891cf7b5a979 Mon Sep 17 00:00:00 2001 From: Pierre Habouzit Date: Fri, 7 Aug 2009 14:16:01 +0200 Subject: [PATCH 0953/1342] perf record: Fix the -A UI for empty or non-existent perf.data 1. Ignore the -A argument if there is no perf.data file 2. Treat an empty file like a non existent file. Else, perf will try to read the perf.data header, and fail with an error. Treating an empty file like a non-existent file makes sense, since an interupted (as in SIGKILLed) perf could leave such files around, and you don't want to annoy the user with errors for files with no data in it. Signed-off-by: Pierre Habouzit Acked-by: Peter Zijlstra Cc: Paul Mackerras Signed-off-by: Ingo Molnar --- tools/perf/builtin-record.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) diff --git a/tools/perf/builtin-record.c b/tools/perf/builtin-record.c index 90c98082af1..0345aad8eba 100644 --- a/tools/perf/builtin-record.c +++ b/tools/perf/builtin-record.c @@ -525,10 +525,14 @@ static int __cmd_record(int argc, const char **argv) signal(SIGCHLD, sig_handler); signal(SIGINT, sig_handler); - if (!stat(output_name, &st) && !force && !append_file) { - fprintf(stderr, "Error, output file %s exists, use -A to append or -f to overwrite.\n", - output_name); - exit(-1); + if (!stat(output_name, &st) && st.st_size) { + if (!force && !append_file) { + fprintf(stderr, "Error, output file %s exists, use -A to append or -f to overwrite.\n", + output_name); + exit(-1); + } + } else { + append_file = 0; } flags = O_CREAT|O_RDWR; -- GitLab From b0efe213f84f7fd5ccfe07053e3d9fb827b7c188 Mon Sep 17 00:00:00 2001 From: Frederic Weisbecker Date: Sat, 8 Aug 2009 02:16:23 +0200 Subject: [PATCH 0954/1342] perf tools: callchain: Fix spurious 'perf report' warnings: ignore empty callchains When the callchain tree comes to insert an empty backtrace, it raises a spurious warning about the fact we are inserting an empty. This is spurious because the radix tree assumes it did something wrong to reach this state. But it didn't, we just met an empty callchain that has to be ignored. This happens occasionally with certain types of call-chain recordings. If it happens it's a big nuisance as perf report output starts with thousands of warning lines. Reported-by: Ingo Molnar Signed-off-by: Frederic Weisbecker Cc: Peter Zijlstra Cc: Arnaldo Carvalho de Melo Cc: Mike Galbraith LKML-Reference: <1249690585-9145-2-git-send-email-fweisbec@gmail.com> Signed-off-by: Ingo Molnar --- tools/perf/util/callchain.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/tools/perf/util/callchain.c b/tools/perf/util/callchain.c index 98c5627f327..a8e67aa9ef4 100644 --- a/tools/perf/util/callchain.c +++ b/tools/perf/util/callchain.c @@ -336,5 +336,7 @@ __append_chain(struct callchain_node *root, struct ip_callchain *chain, void append_chain(struct callchain_node *root, struct ip_callchain *chain, struct symbol **syms) { + if (!chain->nr) + return; __append_chain_children(root, chain, syms, 0); } -- GitLab From b1a88349c37624755b28ac3b3152b48f52c1f487 Mon Sep 17 00:00:00 2001 From: Frederic Weisbecker Date: Sat, 8 Aug 2009 02:16:24 +0200 Subject: [PATCH 0955/1342] perf tools: callchain: Fix 'perf report' display to be callchain by default If we recorded with -g option to record the callchain, right now we require a -g option to perf report as well - and people reported this as unnecessary complication: the user already specified -g once, no need to require it a second time. So if the recording includes call-chains, display the callchain by default from perf report. ( The user can override this default using "-g none" option from perf report. ) Reported-by: Ingo Molnar Signed-off-by: Frederic Weisbecker Cc: Peter Zijlstra Cc: Arnaldo Carvalho de Melo Cc: Mike Galbraith LKML-Reference: <1249690585-9145-3-git-send-email-fweisbec@gmail.com> Signed-off-by: Ingo Molnar --- tools/perf/builtin-report.c | 16 +++++++++++++++- tools/perf/util/callchain.h | 1 + 2 files changed, 16 insertions(+), 1 deletion(-) diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c index a5e2f8df411..c4a8e108e52 100644 --- a/tools/perf/builtin-report.c +++ b/tools/perf/builtin-report.c @@ -68,7 +68,7 @@ static int callchain; static struct callchain_param callchain_param = { - .mode = CHAIN_GRAPH_ABS, + .mode = CHAIN_GRAPH_REL, .min_percent = 0.5 }; @@ -1836,6 +1836,13 @@ static int __cmd_report(void) " -g?\n"); exit(-1); } + } else if (callchain_param.mode != CHAIN_NONE && !callchain) { + callchain = 1; + if (register_callchain_param(&callchain_param) < 0) { + fprintf(stderr, "Can't register callchain" + " params\n"); + exit(-1); + } } if (load_kernel() < 0) { @@ -1974,6 +1981,13 @@ parse_callchain_opt(const struct option *opt __used, const char *arg, else if (!strncmp(tok, "fractal", strlen(arg))) callchain_param.mode = CHAIN_GRAPH_REL; + else if (!strncmp(tok, "none", strlen(arg))) { + callchain_param.mode = CHAIN_NONE; + callchain = 0; + + return 0; + } + else return -1; diff --git a/tools/perf/util/callchain.h b/tools/perf/util/callchain.h index b2d128e07c8..a926ae4f5a1 100644 --- a/tools/perf/util/callchain.h +++ b/tools/perf/util/callchain.h @@ -7,6 +7,7 @@ #include "symbol.h" enum chain_mode { + CHAIN_NONE, CHAIN_FLAT, CHAIN_GRAPH_ABS, CHAIN_GRAPH_REL -- GitLab From 25446036cbfc2c89faacdb4fb4603943d2197dc6 Mon Sep 17 00:00:00 2001 From: Frederic Weisbecker Date: Sat, 8 Aug 2009 02:16:25 +0200 Subject: [PATCH 0956/1342] perf tools: callchain: Fix sum of percentages to be 100% by displaying amount of ignored chains in fractal mode When we filter the callchains below a given percentage, we ignore them and the end result only shows entries that have an upper percentage than the filter threshold. It seems to users then that we have an imbalance in the percentage, as if the sum inside a profiled branch doesn't reach 100%. Since in the past there have been real perf report bugs that showed the same sypmtom, it would be nice to assure the user that the data is perfect and trustable and it all sums up to 100.00%. So fix this by displaying the remaining hits that have been filtered but without more detail than their amount in each branches. Example while filtering below 50%: 7.73% [k] delay_tsc | |--98.22%-- __const_udelay | | | |--86.37%-- ath5k_hw_register_timeout | | ath5k_hw_noise_floor_calibration | | ath5k_hw_reset | | ath5k_reset | | ath5k_config | | ieee80211_hw_config | | | | | |--88.53%-- ieee80211_scan_work | | | worker_thread | | | kthread | | | child_rip | | --11.47%-- [...] | --13.63%-- [...] --1.78%-- [...] Reported-by: Ingo Molnar Signed-off-by: Frederic Weisbecker Cc: Peter Zijlstra Cc: Arnaldo Carvalho de Melo Cc: Mike Galbraith LKML-Reference: <1249690585-9145-4-git-send-email-fweisbec@gmail.com> Signed-off-by: Ingo Molnar --- tools/perf/builtin-report.c | 47 ++++++++++++++++++++++++++++++++++--- 1 file changed, 44 insertions(+), 3 deletions(-) diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c index c4a8e108e52..99274cec0ad 100644 --- a/tools/perf/builtin-report.c +++ b/tools/perf/builtin-report.c @@ -891,6 +891,21 @@ ipchain__fprintf_graph(FILE *fp, struct callchain_list *chain, int depth, return ret; } +static struct symbol *rem_sq_bracket; +static struct callchain_list rem_hits; + +static void init_rem_hits(void) +{ + rem_sq_bracket = malloc(sizeof(*rem_sq_bracket) + 6); + if (!rem_sq_bracket) { + fprintf(stderr, "Not enough memory to display remaining hits\n"); + return; + } + + strcpy(rem_sq_bracket->name, "[...]"); + rem_hits.sym = rem_sq_bracket; +} + static size_t callchain__fprintf_graph(FILE *fp, struct callchain_node *self, u64 total_samples, int depth, int depth_mask) @@ -900,6 +915,7 @@ callchain__fprintf_graph(FILE *fp, struct callchain_node *self, struct callchain_list *chain; int new_depth_mask = depth_mask; u64 new_total; + u64 remaining; size_t ret = 0; int i; @@ -908,17 +924,25 @@ callchain__fprintf_graph(FILE *fp, struct callchain_node *self, else new_total = total_samples; + remaining = new_total; + node = rb_first(&self->rb_root); while (node) { + u64 cumul; + child = rb_entry(node, struct callchain_node, rb_node); + cumul = cumul_hits(child); + remaining -= cumul; /* * The depth mask manages the output of pipes that show * the depth. We don't want to keep the pipes of the current - * level for the last child of this depth + * level for the last child of this depth. + * Except if we have remaining filtered hits. They will + * supersede the last child */ next = rb_next(node); - if (!next) + if (!next && (callchain_param.mode != CHAIN_GRAPH_REL || !remaining)) new_depth_mask &= ~(1 << (depth - 1)); /* @@ -933,7 +957,7 @@ callchain__fprintf_graph(FILE *fp, struct callchain_node *self, ret += ipchain__fprintf_graph(fp, chain, depth, new_depth_mask, i++, new_total, - cumul_hits(child)); + cumul); } ret += callchain__fprintf_graph(fp, child, new_total, depth + 1, @@ -941,6 +965,19 @@ callchain__fprintf_graph(FILE *fp, struct callchain_node *self, node = next; } + if (callchain_param.mode == CHAIN_GRAPH_REL && + remaining && remaining != new_total) { + + if (!rem_sq_bracket) + return ret; + + new_depth_mask &= ~(1 << (depth - 1)); + + ret += ipchain__fprintf_graph(fp, &rem_hits, depth, + new_depth_mask, 0, new_total, + remaining); + } + return ret; } @@ -1361,6 +1398,8 @@ static size_t output__fprintf(FILE *fp, u64 total_samples) unsigned int width; char *col_width = col_width_list_str; + init_rem_hits(); + fprintf(fp, "# Samples: %Ld\n", (u64)total_samples); fprintf(fp, "#\n"); @@ -1432,6 +1471,8 @@ print_entries: } fprintf(fp, "\n"); + free(rem_sq_bracket); + return ret; } -- GitLab From 10b8e3066066708f304e0fc5cfe658e05abf943d Mon Sep 17 00:00:00 2001 From: Frederic Weisbecker Date: Sat, 8 Aug 2009 04:26:35 +0200 Subject: [PATCH 0957/1342] perf_counter: Work around gcc warning by initializing tracepoint record unconditionally MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Despite that the tracepoint record is always present when the PERF_SAMPLE_TP_RECORD flag is set, gcc raises a warning, thinking it might not be initialized: kernel/perf_counter.c: In function ‘perf_counter_output’: kernel/perf_counter.c:2650: warning: ‘tp’ may be used uninitialized in this function Then, initialize it to NULL and always check if it's not NULL before dereference it. Reported-by: Ingo Molnar Signed-off-by: Frederic Weisbecker Cc: Peter Zijlstra Cc: Arnaldo Carvalho de Melo Cc: Mike Galbraith Cc: Paul Mackerras LKML-Reference: <1249698400-5441-2-git-send-email-fweisbec@gmail.com> Signed-off-by: Ingo Molnar --- kernel/perf_counter.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index 615440ab929..117622cb73a 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -2646,7 +2646,7 @@ static void perf_counter_output(struct perf_counter *counter, int nmi, u64 counter; } group_entry; struct perf_callchain_entry *callchain = NULL; - struct perf_tracepoint_record *tp; + struct perf_tracepoint_record *tp = NULL; int callchain_size = 0; u64 time; struct { @@ -2717,7 +2717,8 @@ static void perf_counter_output(struct perf_counter *counter, int nmi, if (sample_type & PERF_SAMPLE_TP_RECORD) { tp = data->private; - header.size += tp->size; + if (tp) + header.size += tp->size; } ret = perf_output_begin(&handle, counter, header.size, nmi, 1); @@ -2783,7 +2784,7 @@ static void perf_counter_output(struct perf_counter *counter, int nmi, } } - if (sample_type & PERF_SAMPLE_TP_RECORD) + if ((sample_type & PERF_SAMPLE_TP_RECORD) && tp) perf_output_copy(&handle, tp->record, tp->size); perf_output_end(&handle); -- GitLab From 3a43ce68ae1758fa6a839386025ef45acb6baa22 Mon Sep 17 00:00:00 2001 From: Frederic Weisbecker Date: Sat, 8 Aug 2009 04:26:37 +0200 Subject: [PATCH 0958/1342] perf_counter: Fix tracepoint sampling to be part of generic sampling Based on Peter's comments, make tracepoint sampling generic just like all the other sampling bits are. This is a rename with no code changes: - PERF_SAMPLE_TP_RECORD to PERF_SAMPLE_RAW - struct perf_tracepoint_record to perf_raw_record We want the system in place that transport tracepoints raw samples events into the perf ring buffer to be generalized and usable by any type of counter. Reported-by; Peter Zijlstra Signed-off-by: Frederic Weisbecker Cc: Peter Zijlstra Cc: Arnaldo Carvalho de Melo Cc: Mike Galbraith Cc: Paul Mackerras LKML-Reference: <1249698400-5441-4-git-send-email-fweisbec@gmail.com> Signed-off-by: Ingo Molnar --- include/linux/perf_counter.h | 10 +++++----- kernel/perf_counter.c | 20 ++++++++++---------- 2 files changed, 15 insertions(+), 15 deletions(-) diff --git a/include/linux/perf_counter.h b/include/linux/perf_counter.h index a67dd5c5b6d..2aabe43c1d0 100644 --- a/include/linux/perf_counter.h +++ b/include/linux/perf_counter.h @@ -121,7 +121,7 @@ enum perf_counter_sample_format { PERF_SAMPLE_CPU = 1U << 7, PERF_SAMPLE_PERIOD = 1U << 8, PERF_SAMPLE_STREAM_ID = 1U << 9, - PERF_SAMPLE_TP_RECORD = 1U << 10, + PERF_SAMPLE_RAW = 1U << 10, PERF_SAMPLE_MAX = 1U << 11, /* non-ABI */ }; @@ -414,9 +414,9 @@ struct perf_callchain_entry { __u64 ip[PERF_MAX_STACK_DEPTH]; }; -struct perf_tracepoint_record { - int size; - char *record; +struct perf_raw_record { + u32 size; + void *data; }; struct task_struct; @@ -687,7 +687,7 @@ struct perf_sample_data { struct pt_regs *regs; u64 addr; u64 period; - void *private; + struct perf_raw_record *raw; }; extern int perf_counter_overflow(struct perf_counter *counter, int nmi, diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index 117622cb73a..00231054041 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -2646,7 +2646,7 @@ static void perf_counter_output(struct perf_counter *counter, int nmi, u64 counter; } group_entry; struct perf_callchain_entry *callchain = NULL; - struct perf_tracepoint_record *tp = NULL; + struct perf_raw_record *raw = NULL; int callchain_size = 0; u64 time; struct { @@ -2715,10 +2715,10 @@ static void perf_counter_output(struct perf_counter *counter, int nmi, header.size += sizeof(u64); } - if (sample_type & PERF_SAMPLE_TP_RECORD) { - tp = data->private; - if (tp) - header.size += tp->size; + if (sample_type & PERF_SAMPLE_RAW) { + raw = data->raw; + if (raw) + header.size += raw->size; } ret = perf_output_begin(&handle, counter, header.size, nmi, 1); @@ -2784,8 +2784,8 @@ static void perf_counter_output(struct perf_counter *counter, int nmi, } } - if ((sample_type & PERF_SAMPLE_TP_RECORD) && tp) - perf_output_copy(&handle, tp->record, tp->size); + if ((sample_type & PERF_SAMPLE_RAW) && raw) + perf_output_copy(&handle, raw->data, raw->size); perf_output_end(&handle); } @@ -3740,15 +3740,15 @@ static const struct pmu perf_ops_task_clock = { void perf_tpcounter_event(int event_id, u64 addr, u64 count, void *record, int entry_size) { - struct perf_tracepoint_record tp = { + struct perf_raw_record raw = { .size = entry_size, - .record = record, + .data = record, }; struct perf_sample_data data = { .regs = get_irq_regs(), .addr = addr, - .private = &tp, + .raw = &raw, }; if (!data.regs) -- GitLab From 3a80b4a3539696f4b0574876326860323035a302 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Fri, 7 Aug 2009 19:49:01 +0200 Subject: [PATCH 0959/1342] perf_counter: Fix a race on perf_counter_ctx While extending perfcounters with BTS hw-tracing, Markus Metzger managed to trigger this warning: [ 995.557128] WARNING: at kernel/perf_counter.c:1191 __perf_counter_task_sched_out+0x48/0x6b() triggers because commit 9f498cc5be7e013d8d6e4c616980ed0ffc8680d2 (perf_counter: Full task tracing) removed clearing of tsk->perf_counter_ctxp out from under ctx->lock which introduced a race (against perf_lock_task_context). Move it back and deal with the exit notification by explicitly passing along the former task context. Reported-by: Markus T Metzger Signed-off-by: Peter Zijlstra Cc: Paul Mackerras LKML-Reference: <1249667341.17467.5.camel@twins> Signed-off-by: Ingo Molnar --- kernel/perf_counter.c | 30 +++++++++++++++--------------- 1 file changed, 15 insertions(+), 15 deletions(-) diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index 00231054041..546e62d6294 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -2850,7 +2850,8 @@ perf_counter_read_event(struct perf_counter *counter, */ struct perf_task_event { - struct task_struct *task; + struct task_struct *task; + struct perf_counter_context *task_ctx; struct { struct perf_event_header header; @@ -2910,24 +2911,23 @@ static void perf_counter_task_ctx(struct perf_counter_context *ctx, static void perf_counter_task_event(struct perf_task_event *task_event) { struct perf_cpu_context *cpuctx; - struct perf_counter_context *ctx; + struct perf_counter_context *ctx = task_event->task_ctx; cpuctx = &get_cpu_var(perf_cpu_context); perf_counter_task_ctx(&cpuctx->ctx, task_event); put_cpu_var(perf_cpu_context); rcu_read_lock(); - /* - * doesn't really matter which of the child contexts the - * events ends up in. - */ - ctx = rcu_dereference(current->perf_counter_ctxp); + if (!ctx) + ctx = rcu_dereference(task_event->task->perf_counter_ctxp); if (ctx) perf_counter_task_ctx(ctx, task_event); rcu_read_unlock(); } -static void perf_counter_task(struct task_struct *task, int new) +static void perf_counter_task(struct task_struct *task, + struct perf_counter_context *task_ctx, + int new) { struct perf_task_event task_event; @@ -2937,8 +2937,9 @@ static void perf_counter_task(struct task_struct *task, int new) return; task_event = (struct perf_task_event){ - .task = task, - .event = { + .task = task, + .task_ctx = task_ctx, + .event = { .header = { .type = new ? PERF_EVENT_FORK : PERF_EVENT_EXIT, .misc = 0, @@ -2956,7 +2957,7 @@ static void perf_counter_task(struct task_struct *task, int new) void perf_counter_fork(struct task_struct *task) { - perf_counter_task(task, 1); + perf_counter_task(task, NULL, 1); } /* @@ -4310,7 +4311,7 @@ void perf_counter_exit_task(struct task_struct *child) unsigned long flags; if (likely(!child->perf_counter_ctxp)) { - perf_counter_task(child, 0); + perf_counter_task(child, NULL, 0); return; } @@ -4330,6 +4331,7 @@ void perf_counter_exit_task(struct task_struct *child) * incremented the context's refcount before we do put_ctx below. */ spin_lock(&child_ctx->lock); + child->perf_counter_ctxp = NULL; /* * If this context is a clone; unclone it so it can't get * swapped to another process while we're removing all @@ -4343,9 +4345,7 @@ void perf_counter_exit_task(struct task_struct *child) * won't get any samples after PERF_EVENT_EXIT. We can however still * get a few PERF_EVENT_READ events. */ - perf_counter_task(child, 0); - - child->perf_counter_ctxp = NULL; + perf_counter_task(child, child_ctx, 0); /* * We can recurse on the same lock type through: -- GitLab From c24b513337f06712b8c81eb4f1413d44591dfee7 Mon Sep 17 00:00:00 2001 From: "Carlos R. Mafra" Date: Wed, 5 Aug 2009 20:53:34 +0200 Subject: [PATCH 0960/1342] perf: "Longum est iter per praecepta, breve et efficax per exempla" A few examples of how 'perf' can be used, from an e-mail by Ingo Molnar http://lkml.org/lkml/2009/8/4/346. Signed-off-by: Carlos R. Mafra Cc: Peter Zijlstra Cc: Valdis.Kletnieks@vt.edu LKML-Reference: <20090805185334.GA4535@Pilar.aei.mpg.de> Signed-off-by: Ingo Molnar --- tools/perf/Documentation/perf-examples.txt | 225 +++++++++++++++++++++ 1 file changed, 225 insertions(+) create mode 100644 tools/perf/Documentation/perf-examples.txt diff --git a/tools/perf/Documentation/perf-examples.txt b/tools/perf/Documentation/perf-examples.txt new file mode 100644 index 00000000000..8eb6c489fb1 --- /dev/null +++ b/tools/perf/Documentation/perf-examples.txt @@ -0,0 +1,225 @@ + + ------------------------------ + ****** perf by examples ****** + ------------------------------ + +[ From an e-mail by Ingo Molnar, http://lkml.org/lkml/2009/8/4/346 ] + + +First, discovery/enumeration of available counters can be done via +'perf list': + +titan:~> perf list + [...] + kmem:kmalloc [Tracepoint event] + kmem:kmem_cache_alloc [Tracepoint event] + kmem:kmalloc_node [Tracepoint event] + kmem:kmem_cache_alloc_node [Tracepoint event] + kmem:kfree [Tracepoint event] + kmem:kmem_cache_free [Tracepoint event] + kmem:mm_page_free_direct [Tracepoint event] + kmem:mm_pagevec_free [Tracepoint event] + kmem:mm_page_alloc [Tracepoint event] + kmem:mm_page_alloc_zone_locked [Tracepoint event] + kmem:mm_page_pcpu_drain [Tracepoint event] + kmem:mm_page_alloc_extfrag [Tracepoint event] + +Then any (or all) of the above event sources can be activated and +measured. For example the page alloc/free properties of a 'hackbench +run' are: + + titan:~> perf stat -e kmem:mm_page_pcpu_drain -e kmem:mm_page_alloc + -e kmem:mm_pagevec_free -e kmem:mm_page_free_direct ./hackbench 10 + Time: 0.575 + + Performance counter stats for './hackbench 10': + + 13857 kmem:mm_page_pcpu_drain + 27576 kmem:mm_page_alloc + 6025 kmem:mm_pagevec_free + 20934 kmem:mm_page_free_direct + + 0.613972165 seconds time elapsed + +You can observe the statistical properties as well, by using the +'repeat the workload N times' feature of perf stat: + + titan:~> perf stat --repeat 5 -e kmem:mm_page_pcpu_drain -e + kmem:mm_page_alloc -e kmem:mm_pagevec_free -e + kmem:mm_page_free_direct ./hackbench 10 + Time: 0.627 + Time: 0.644 + Time: 0.564 + Time: 0.559 + Time: 0.626 + + Performance counter stats for './hackbench 10' (5 runs): + + 12920 kmem:mm_page_pcpu_drain ( +- 3.359% ) + 25035 kmem:mm_page_alloc ( +- 3.783% ) + 6104 kmem:mm_pagevec_free ( +- 0.934% ) + 18376 kmem:mm_page_free_direct ( +- 4.941% ) + + 0.643954516 seconds time elapsed ( +- 2.363% ) + +Furthermore, these tracepoints can be used to sample the workload as +well. For example the page allocations done by a 'git gc' can be +captured the following way: + + titan:~/git> perf record -f -e kmem:mm_page_alloc -c 1 ./git gc + Counting objects: 1148, done. + Delta compression using up to 2 threads. + Compressing objects: 100% (450/450), done. + Writing objects: 100% (1148/1148), done. + Total 1148 (delta 690), reused 1148 (delta 690) + [ perf record: Captured and wrote 0.267 MB perf.data (~11679 samples) ] + +To check which functions generated page allocations: + + titan:~/git> perf report + # Samples: 10646 + # + # Overhead Command Shared Object + # ........ ............... .......................... + # + 23.57% git-repack /lib64/libc-2.5.so + 21.81% git /lib64/libc-2.5.so + 14.59% git ./git + 11.79% git-repack ./git + 7.12% git /lib64/ld-2.5.so + 3.16% git-repack /lib64/libpthread-2.5.so + 2.09% git-repack /bin/bash + 1.97% rm /lib64/libc-2.5.so + 1.39% mv /lib64/ld-2.5.so + 1.37% mv /lib64/libc-2.5.so + 1.12% git-repack /lib64/ld-2.5.so + 0.95% rm /lib64/ld-2.5.so + 0.90% git-update-serv /lib64/libc-2.5.so + 0.73% git-update-serv /lib64/ld-2.5.so + 0.68% perf /lib64/libpthread-2.5.so + 0.64% git-repack /usr/lib64/libz.so.1.2.3 + +Or to see it on a more finegrained level: + +titan:~/git> perf report --sort comm,dso,symbol +# Samples: 10646 +# +# Overhead Command Shared Object Symbol +# ........ ............... .......................... ...... +# + 9.35% git-repack ./git [.] insert_obj_hash + 9.12% git ./git [.] insert_obj_hash + 7.31% git /lib64/libc-2.5.so [.] memcpy + 6.34% git-repack /lib64/libc-2.5.so [.] _int_malloc + 6.24% git-repack /lib64/libc-2.5.so [.] memcpy + 5.82% git-repack /lib64/libc-2.5.so [.] __GI___fork + 5.47% git /lib64/libc-2.5.so [.] _int_malloc + 2.99% git /lib64/libc-2.5.so [.] memset + +Furthermore, call-graph sampling can be done too, of page +allocations - to see precisely what kind of page allocations there +are: + + titan:~/git> perf record -f -g -e kmem:mm_page_alloc -c 1 ./git gc + Counting objects: 1148, done. + Delta compression using up to 2 threads. + Compressing objects: 100% (450/450), done. + Writing objects: 100% (1148/1148), done. + Total 1148 (delta 690), reused 1148 (delta 690) + [ perf record: Captured and wrote 0.963 MB perf.data (~42069 samples) ] + + titan:~/git> perf report -g + # Samples: 10686 + # + # Overhead Command Shared Object + # ........ ............... .......................... + # + 23.25% git-repack /lib64/libc-2.5.so + | + |--50.00%-- _int_free + | + |--37.50%-- __GI___fork + | make_child + | + |--12.50%-- ptmalloc_unlock_all2 + | make_child + | + --6.25%-- __GI_strcpy + 21.61% git /lib64/libc-2.5.so + | + |--30.00%-- __GI_read + | | + | --83.33%-- git_config_from_file + | git_config + | | + [...] + +Or you can observe the whole system's page allocations for 10 +seconds: + +titan:~/git> perf stat -a -e kmem:mm_page_pcpu_drain -e +kmem:mm_page_alloc -e kmem:mm_pagevec_free -e +kmem:mm_page_free_direct sleep 10 + + Performance counter stats for 'sleep 10': + + 171585 kmem:mm_page_pcpu_drain + 322114 kmem:mm_page_alloc + 73623 kmem:mm_pagevec_free + 254115 kmem:mm_page_free_direct + + 10.000591410 seconds time elapsed + +Or observe how fluctuating the page allocations are, via statistical +analysis done over ten 1-second intervals: + + titan:~/git> perf stat --repeat 10 -a -e kmem:mm_page_pcpu_drain -e + kmem:mm_page_alloc -e kmem:mm_pagevec_free -e + kmem:mm_page_free_direct sleep 1 + + Performance counter stats for 'sleep 1' (10 runs): + + 17254 kmem:mm_page_pcpu_drain ( +- 3.709% ) + 34394 kmem:mm_page_alloc ( +- 4.617% ) + 7509 kmem:mm_pagevec_free ( +- 4.820% ) + 25653 kmem:mm_page_free_direct ( +- 3.672% ) + + 1.058135029 seconds time elapsed ( +- 3.089% ) + +Or you can annotate the recorded 'git gc' run on a per symbol basis +and check which instructions/source-code generated page allocations: + + titan:~/git> perf annotate __GI___fork + ------------------------------------------------ + Percent | Source code & Disassembly of libc-2.5.so + ------------------------------------------------ + : + : + : Disassembly of section .plt: + : Disassembly of section .text: + : + : 00000031a2e95560 <__fork>: + [...] + 0.00 : 31a2e95602: b8 38 00 00 00 mov $0x38,%eax + 0.00 : 31a2e95607: 0f 05 syscall + 83.42 : 31a2e95609: 48 3d 00 f0 ff ff cmp $0xfffffffffffff000,%rax + 0.00 : 31a2e9560f: 0f 87 4d 01 00 00 ja 31a2e95762 <__fork+0x202> + 0.00 : 31a2e95615: 85 c0 test %eax,%eax + +( this shows that 83.42% of __GI___fork's page allocations come from + the 0x38 system call it performs. ) + +etc. etc. - a lot more is possible. I could list a dozen of +other different usecases straight away - neither of which is +possible via /proc/vmstat. + +/proc/vmstat is not in the same league really, in terms of +expressive power of system analysis and performance +analysis. + +All that the above results needed were those new tracepoints +in include/tracing/events/kmem.h. + + Ingo + + -- GitLab From 183f3b0887083d36c8a25cd5e3518906415d1889 Mon Sep 17 00:00:00 2001 From: Mike Galbraith Date: Sat, 8 Aug 2009 14:14:15 +0200 Subject: [PATCH 0961/1342] perf_counter tools: Fix libbfd detection for systems with libz dependency Due to a libz dependency in some distro's binutils package, C++ demangle support isn't compiled in despite the necessary libraries being available. Fix this by adding a -lz link test to the dependency detection rules. Signed-off-by: Mike Galbraith Acked-by: Peter Zijlstra LKML-Reference: <1249733655.6929.5.camel@marge.simson.net> Signed-off-by: Ingo Molnar --- tools/perf/Makefile | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/tools/perf/Makefile b/tools/perf/Makefile index 1916e44b9bb..60411e94113 100644 --- a/tools/perf/Makefile +++ b/tools/perf/Makefile @@ -387,10 +387,14 @@ else has_bfd_iberty := $(shell sh -c "(echo '\#include '; echo 'int main(void) { bfd_demangle(0, 0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -lbfd -liberty > /dev/null 2>&1 && echo y") + has_bfd_iberty_z := $(shell sh -c "(echo '\#include '; echo 'int main(void) { bfd_demangle(0, 0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -lbfd -liberty -lz > /dev/null 2>&1 && echo y") + ifeq ($(has_bfd),y) EXTLIBS += -lbfd else ifeq ($(has_bfd_iberty),y) EXTLIBS += -lbfd -liberty + else ifeq ($(has_bfd_iberty_z),y) + EXTLIBS += -lbfd -liberty -lz else msg := $(warning No bfd.h/libbfd found, install binutils-dev[el] to gain symbol demangling) BASIC_CFLAGS += -DNO_DEMANGLE -- GitLab From c0a8865e32c8d1a562db38e06ef31ef23282f646 Mon Sep 17 00:00:00 2001 From: Frederic Weisbecker Date: Sun, 9 Aug 2009 04:19:15 +0200 Subject: [PATCH 0962/1342] perf tools: callchain: Fix bad rounding of minimum rate Sometimes we get callchain branches that have a rate under the limit given by the user. Say you launched: perf record -f -g -a ./hackbench 10 perf report -g fractal,10.0 And you got: 2.33% hackbench [kernel] [k] _spin_lock_irqsave | |--78.57%-- remove_wait_queue | poll_freewait | do_sys_poll | sys_poll | sysenter_dispatch | 0xf7ffa430 | 0x1ffadea3c | |--7.14%-- __up_read | up_read | do_page_fault | page_fault | 0xf7ffa430 | 0xa0df710000000a ... It is abnormal to get a 7.14% branch whereas we passed a 10% filter. The problem is that we round down the minimum threshold. This happens mostly when we have very low number of events. If the total amount of your branch is 4 and you have a subranch of 3 events, filtering to 90% will be computed like follows: limit = 4 * 0.9; The result is about 3.6, but the cast to integer will round down to 3. It means that our filter is actually of 75% We must then explicitly round up the minimum threshold. Reported-by: Ingo Molnar Signed-off-by: Frederic Weisbecker Cc: acme@redhat.com Cc: peterz@infradead.org Cc: efault@gmx.de LKML-Reference: <20090809024235.GA10146@nowhere> Signed-off-by: Ingo Molnar --- tools/perf/util/callchain.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/tools/perf/util/callchain.c b/tools/perf/util/callchain.c index a8e67aa9ef4..01147341164 100644 --- a/tools/perf/util/callchain.c +++ b/tools/perf/util/callchain.c @@ -13,6 +13,7 @@ #include #include #include +#include #include "callchain.h" @@ -112,7 +113,7 @@ static void __sort_chain_graph_rel(struct callchain_node *node, u64 min_hit; node->rb_root = RB_ROOT; - min_hit = node->children_hit * min_percent / 100.0; + min_hit = ceil(node->children_hit * min_percent); chain_for_each_child(child, node) { __sort_chain_graph_rel(child, min_percent); @@ -126,7 +127,7 @@ static void sort_chain_graph_rel(struct rb_root *rb_root, struct callchain_node *chain_root, u64 min_hit __used, struct callchain_param *param) { - __sort_chain_graph_rel(chain_root, param->min_percent); + __sort_chain_graph_rel(chain_root, param->min_percent / 100.0); rb_root->rb_node = chain_root->rb_root.rb_node; } -- GitLab From c8c00a6915a2e3d10416e8bdd3138429beb96210 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Mon, 10 Aug 2009 12:50:52 +1000 Subject: [PATCH 0963/1342] Remove deadlock potential in md_open A recent commit: commit 449aad3e25358812c43afc60918c5ad3819488e7 introduced the possibility of an A-B/B-A deadlock between bd_mutex and reconfig_mutex. __blkdev_get holds bd_mutex while calling md_open which takes reconfig_mutex, do_md_run is always called with reconfig_mutex held, and it now takes bd_mutex in the call the revalidate_disk. This potential deadlock was not caught by lockdep due to the use of mutex_lock_interruptible_nexted which was introduced by commit d63a5a74dee87883fda6b7d170244acaac5b05e8 do avoid a warning of an impossible deadlock. It is quite possible to split reconfig_mutex in to two locks. One protects the array data structures while it is being reconfigured, the other ensures that an array is never even partially open while it is being deactivated. In particular, the second lock prevents an open from completing between the time when do_md_stop checks if there are any active opens, and the time when the array is either set read-only, or when ->pers is set to NULL. So we can be certain that no IO is in flight as the array is being destroyed. So create a new lock, open_mutex, just to ensure exclusion between 'open' and 'stop'. This avoids the deadlock and also avoids the lockdep warning mentioned in commit d63a5a74d Reported-by: "Mike Snitzer" Reported-by: "H. Peter Anvin" Signed-off-by: NeilBrown --- drivers/md/md.c | 18 ++++++++++-------- drivers/md/md.h | 10 ++++++++++ 2 files changed, 20 insertions(+), 8 deletions(-) diff --git a/drivers/md/md.c b/drivers/md/md.c index 5b98bea4ff9..5614500092e 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -359,6 +359,7 @@ static mddev_t * mddev_find(dev_t unit) else new->md_minor = MINOR(unit) >> MdpMinorShift; + mutex_init(&new->open_mutex); mutex_init(&new->reconfig_mutex); INIT_LIST_HEAD(&new->disks); INIT_LIST_HEAD(&new->all_mddevs); @@ -4304,12 +4305,11 @@ static int do_md_stop(mddev_t * mddev, int mode, int is_open) struct gendisk *disk = mddev->gendisk; mdk_rdev_t *rdev; + mutex_lock(&mddev->open_mutex); if (atomic_read(&mddev->openers) > is_open) { printk("md: %s still in use.\n",mdname(mddev)); - return -EBUSY; - } - - if (mddev->pers) { + err = -EBUSY; + } else if (mddev->pers) { if (mddev->sync_thread) { set_bit(MD_RECOVERY_FROZEN, &mddev->recovery); @@ -4367,7 +4367,10 @@ static int do_md_stop(mddev_t * mddev, int mode, int is_open) set_disk_ro(disk, 1); clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery); } - +out: + mutex_unlock(&mddev->open_mutex); + if (err) + return err; /* * Free resources if final stop */ @@ -4433,7 +4436,6 @@ static int do_md_stop(mddev_t * mddev, int mode, int is_open) blk_integrity_unregister(disk); md_new_event(mddev); sysfs_notify_dirent(mddev->sysfs_state); -out: return err; } @@ -5518,12 +5520,12 @@ static int md_open(struct block_device *bdev, fmode_t mode) } BUG_ON(mddev != bdev->bd_disk->private_data); - if ((err = mutex_lock_interruptible_nested(&mddev->reconfig_mutex, 1))) + if ((err = mutex_lock_interruptible(&mddev->open_mutex))) goto out; err = 0; atomic_inc(&mddev->openers); - mddev_unlock(mddev); + mutex_unlock(&mddev->open_mutex); check_disk_change(bdev); out: diff --git a/drivers/md/md.h b/drivers/md/md.h index 78f03168baf..f8fc188bc76 100644 --- a/drivers/md/md.h +++ b/drivers/md/md.h @@ -223,6 +223,16 @@ struct mddev_s * so we don't loop trying */ int in_sync; /* know to not need resync */ + /* 'open_mutex' avoids races between 'md_open' and 'do_md_stop', so + * that we are never stopping an array while it is open. + * 'reconfig_mutex' protects all other reconfiguration. + * These locks are separate due to conflicting interactions + * with bdev->bd_mutex. + * Lock ordering is: + * reconfig_mutex -> bd_mutex : e.g. do_md_run -> revalidate_disk + * bd_mutex -> open_mutex: e.g. __blkdev_get -> md_open + */ + struct mutex open_mutex; struct mutex reconfig_mutex; atomic_t active; /* general refcount */ atomic_t openers; /* number of active opens */ -- GitLab From cb2f33e9596632979c140c243ac1e8e994f62180 Mon Sep 17 00:00:00 2001 From: Chris Snook Date: Thu, 6 Aug 2009 12:19:31 +0000 Subject: [PATCH 0964/1342] MAINTAINERS: update atlx contact info Update MAINTAINERS to reflect my current (non-)affiliation. Anyone hiring? Signed-off-by: Chris Snook Cc: Jay Cliburn Cc: Jie Yang Cc: "David S. Miller" Signed-off-by: Andrew Morton Signed-off-by: David S. Miller --- MAINTAINERS | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/MAINTAINERS b/MAINTAINERS index b1114cfac6b..fa76ad0a37e 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -904,7 +904,7 @@ F: drivers/input/misc/ati_remote2.c ATLX ETHERNET DRIVERS M: Jay Cliburn -M: Chris Snook +M: Chris Snook M: Jie Yang L: atl1-devel@lists.sourceforge.net W: http://sourceforge.net/projects/atl1 -- GitLab From 5d5ceb8bdde403529ad9849f300dc80b1884550f Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Thu, 6 Aug 2009 13:06:03 +0000 Subject: [PATCH 0965/1342] irda: fix read buffer overflow io[i] is read before the bounds check on i, order should be reversed. Signed-off-by: Roel Kluin Cc: Samuel Ortiz Signed-off-by: Andrew Morton Signed-off-by: David S. Miller --- drivers/net/irda/w83977af_ir.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/irda/w83977af_ir.c b/drivers/net/irda/w83977af_ir.c index d0883835b0c..fe4f2b2bff9 100644 --- a/drivers/net/irda/w83977af_ir.c +++ b/drivers/net/irda/w83977af_ir.c @@ -115,7 +115,7 @@ static int __init w83977af_init(void) IRDA_DEBUG(0, "%s()\n", __func__ ); - for (i=0; (io[i] < 2000) && (i < ARRAY_SIZE(dev_self)); i++) { + for (i=0; i < ARRAY_SIZE(dev_self) && io[i] < 2000; i++) { if (w83977af_open(i, io[i], irq[i], dma[i]) == 0) return 0; } -- GitLab From 082ba88a5e6b1425abed3fae4ad65e0e985ed081 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Thu, 6 Aug 2009 13:06:56 +0000 Subject: [PATCH 0966/1342] atlx: strncpy does not null terminate string strlcpy() will always null terminate the string. Signed-off-by: Roel Kluin Cc: Jay Cliburn Cc: Chris Snook Cc: Jie Yang Signed-off-by: Andrew Morton Signed-off-by: David S. Miller --- drivers/net/atl1c/atl1c_ethtool.c | 8 ++++---- drivers/net/atlx/atl1.c | 8 ++++---- 2 files changed, 8 insertions(+), 8 deletions(-) diff --git a/drivers/net/atl1c/atl1c_ethtool.c b/drivers/net/atl1c/atl1c_ethtool.c index 607007d75b6..00d11b480af 100644 --- a/drivers/net/atl1c/atl1c_ethtool.c +++ b/drivers/net/atl1c/atl1c_ethtool.c @@ -232,11 +232,11 @@ static void atl1c_get_drvinfo(struct net_device *netdev, { struct atl1c_adapter *adapter = netdev_priv(netdev); - strncpy(drvinfo->driver, atl1c_driver_name, sizeof(drvinfo->driver)); - strncpy(drvinfo->version, atl1c_driver_version, + strlcpy(drvinfo->driver, atl1c_driver_name, sizeof(drvinfo->driver)); + strlcpy(drvinfo->version, atl1c_driver_version, sizeof(drvinfo->version)); - strncpy(drvinfo->fw_version, "N/A", sizeof(drvinfo->fw_version)); - strncpy(drvinfo->bus_info, pci_name(adapter->pdev), + strlcpy(drvinfo->fw_version, "N/A", sizeof(drvinfo->fw_version)); + strlcpy(drvinfo->bus_info, pci_name(adapter->pdev), sizeof(drvinfo->bus_info)); drvinfo->n_stats = 0; drvinfo->testinfo_len = 0; diff --git a/drivers/net/atlx/atl1.c b/drivers/net/atlx/atl1.c index 94d7325caf4..8bca12f7139 100644 --- a/drivers/net/atlx/atl1.c +++ b/drivers/net/atlx/atl1.c @@ -3378,11 +3378,11 @@ static void atl1_get_drvinfo(struct net_device *netdev, { struct atl1_adapter *adapter = netdev_priv(netdev); - strncpy(drvinfo->driver, ATLX_DRIVER_NAME, sizeof(drvinfo->driver)); - strncpy(drvinfo->version, ATLX_DRIVER_VERSION, + strlcpy(drvinfo->driver, ATLX_DRIVER_NAME, sizeof(drvinfo->driver)); + strlcpy(drvinfo->version, ATLX_DRIVER_VERSION, sizeof(drvinfo->version)); - strncpy(drvinfo->fw_version, "N/A", sizeof(drvinfo->fw_version)); - strncpy(drvinfo->bus_info, pci_name(adapter->pdev), + strlcpy(drvinfo->fw_version, "N/A", sizeof(drvinfo->fw_version)); + strlcpy(drvinfo->bus_info, pci_name(adapter->pdev), sizeof(drvinfo->bus_info)); drvinfo->eedump_len = ATL1_EEDUMP_LEN; } -- GitLab From b79a79471bd31d737c939a6ddc347417047b4320 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Jussi=20M=C3=A4ki?= Date: Thu, 6 Aug 2009 21:38:14 +0000 Subject: [PATCH 0967/1342] Fix xfrm hash collisions by changing __xfrm4_daddr_saddr_hash to hash addresses with addition This patch fixes hash collisions in cases where number of entries have incrementing IP source and destination addresses from single respective subnets (i.e. 192.168.0.1-172.16.0.1, 192.168.0.2-172.16.0.2, and so on.). Signed-off-by: Jussi Maki Signed-off-by: David S. Miller --- net/xfrm/xfrm_hash.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/xfrm/xfrm_hash.h b/net/xfrm/xfrm_hash.h index d401dc8f05e..e5195c99f71 100644 --- a/net/xfrm/xfrm_hash.h +++ b/net/xfrm/xfrm_hash.h @@ -16,7 +16,7 @@ static inline unsigned int __xfrm6_addr_hash(xfrm_address_t *addr) static inline unsigned int __xfrm4_daddr_saddr_hash(xfrm_address_t *daddr, xfrm_address_t *saddr) { - return ntohl(daddr->a4 ^ saddr->a4); + return ntohl(daddr->a4 + saddr->a4); } static inline unsigned int __xfrm6_daddr_saddr_hash(xfrm_address_t *daddr, xfrm_address_t *saddr) -- GitLab From e84b90ae5eb3c112d1f208964df1d8156a538289 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Thu, 6 Aug 2009 20:27:04 +0000 Subject: [PATCH 0968/1342] can: Fix raw_getname() leak raw_getname() can leak 10 bytes of kernel memory to user (two bytes hole between can_family and can_ifindex, 8 bytes at the end of sockaddr_can structure) Signed-off-by: Eric Dumazet Acked-by: Oliver Hartkopp Signed-off-by: David S. Miller --- net/can/raw.c | 1 + 1 file changed, 1 insertion(+) diff --git a/net/can/raw.c b/net/can/raw.c index f4cc44548bd..db3152df7d2 100644 --- a/net/can/raw.c +++ b/net/can/raw.c @@ -401,6 +401,7 @@ static int raw_getname(struct socket *sock, struct sockaddr *uaddr, if (peer) return -EOPNOTSUPP; + memset(addr, 0, sizeof(*addr)); addr->can_family = AF_CAN; addr->can_ifindex = ro->ifindex; -- GitLab From 9555b31e8c29d2000e1e1f569f6f242ebd596e47 Mon Sep 17 00:00:00 2001 From: Greg Ungerer Date: Thu, 6 Aug 2009 17:58:18 +0000 Subject: [PATCH 0969/1342] fec: fix FEC driver packet transmission breakage Commit f0b3fbeae11a526c3d308b691684589ee37c359b ("FEC Buffer rework") breaks transmission of packets where the skb data buffer is not memory aligned according to FEC_ALIGNMENT. It incorrectly passes to dma_sync_single() the buffer address directly from the skb, instead of the address calculated for use (which may be the skb address or one of the bounce buffers). It seems there is no use converting the cpu address of the buffer to a physical either, since dma_map_single() expects the cpu address and will return the dma address to use in the descriptor. So remove the use of __pa() on the buffer address as well. This patch is against 2.6.30-rc5. This breakage is a regression over 2.6.30, which does not have this problem. Signed-off-by: Greg Ungerer Signed-off-by: David S. Miller --- drivers/net/fec.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) diff --git a/drivers/net/fec.c b/drivers/net/fec.c index d4b98074b1b..c9fd82d3a80 100644 --- a/drivers/net/fec.c +++ b/drivers/net/fec.c @@ -285,6 +285,7 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev) { struct fec_enet_private *fep = netdev_priv(dev); struct bufdesc *bdp; + void *bufaddr; unsigned short status; unsigned long flags; @@ -312,7 +313,7 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev) status &= ~BD_ENET_TX_STATS; /* Set buffer length and buffer pointer */ - bdp->cbd_bufaddr = __pa(skb->data); + bufaddr = skb->data; bdp->cbd_datlen = skb->len; /* @@ -320,11 +321,11 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev) * 4-byte boundaries. Use bounce buffers to copy data * and get it aligned. Ugh. */ - if (bdp->cbd_bufaddr & FEC_ALIGNMENT) { + if (((unsigned long) bufaddr) & FEC_ALIGNMENT) { unsigned int index; index = bdp - fep->tx_bd_base; memcpy(fep->tx_bounce[index], (void *)skb->data, skb->len); - bdp->cbd_bufaddr = __pa(fep->tx_bounce[index]); + bufaddr = fep->tx_bounce[index]; } /* Save skb pointer */ @@ -336,7 +337,7 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev) /* Push the data cache so the CPM does not get stale memory * data. */ - bdp->cbd_bufaddr = dma_map_single(&dev->dev, skb->data, + bdp->cbd_bufaddr = dma_map_single(&dev->dev, bufaddr, FEC_ENET_TX_FRSIZE, DMA_TO_DEVICE); /* Send it on its way. Tell FEC it's ready, interrupt when done, -- GitLab From 876bfd4d0f18cd1f698249870c7e7fb944de1c26 Mon Sep 17 00:00:00 2001 From: Herbert Xu Date: Thu, 6 Aug 2009 14:22:44 +0000 Subject: [PATCH 0970/1342] tun: Extend RTNL lock coverage over whole ioctl As it is, parts of the ioctl runs under the RTNL and parts of it do not. The unlocked section is still protected by the BKL, but there can be subtle races. For example, Eric Biederman and Paul Moore observed that if two threads tried to create two tun devices on the same file descriptor, then unexpected results may occur. As there isn't anything in the ioctl that is expected to sleep indefinitely, we can prevent this from occurring by extending the RTNL lock coverage. This also allows to get rid of the BKL. Finally, I changed tun_get_iff to take a tun device in order to avoid calling tun_put which would dead-lock as it also tries to take the RTNL lock. Signed-off-by: Herbert Xu Signed-off-by: David S. Miller --- drivers/net/tun.c | 50 ++++++++++++++++++----------------------------- 1 file changed, 19 insertions(+), 31 deletions(-) diff --git a/drivers/net/tun.c b/drivers/net/tun.c index 027f7aba26a..42b6c6319bc 100644 --- a/drivers/net/tun.c +++ b/drivers/net/tun.c @@ -1048,20 +1048,15 @@ static int tun_set_iff(struct net *net, struct file *file, struct ifreq *ifr) return err; } -static int tun_get_iff(struct net *net, struct file *file, struct ifreq *ifr) +static int tun_get_iff(struct net *net, struct tun_struct *tun, + struct ifreq *ifr) { - struct tun_struct *tun = tun_get(file); - - if (!tun) - return -EBADFD; - DBG(KERN_INFO "%s: tun_get_iff\n", tun->dev->name); strcpy(ifr->ifr_name, tun->dev->name); ifr->ifr_flags = tun_flags(tun); - tun_put(tun); return 0; } @@ -1105,8 +1100,8 @@ static int set_offload(struct net_device *dev, unsigned long arg) return 0; } -static int tun_chr_ioctl(struct inode *inode, struct file *file, - unsigned int cmd, unsigned long arg) +static long tun_chr_ioctl(struct file *file, unsigned int cmd, + unsigned long arg) { struct tun_file *tfile = file->private_data; struct tun_struct *tun; @@ -1128,34 +1123,32 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file, (unsigned int __user*)argp); } + rtnl_lock(); + tun = __tun_get(tfile); if (cmd == TUNSETIFF && !tun) { - int err; - ifr.ifr_name[IFNAMSIZ-1] = '\0'; - rtnl_lock(); - err = tun_set_iff(tfile->net, file, &ifr); - rtnl_unlock(); + ret = tun_set_iff(tfile->net, file, &ifr); - if (err) - return err; + if (ret) + goto unlock; if (copy_to_user(argp, &ifr, sizeof(ifr))) - return -EFAULT; - return 0; + ret = -EFAULT; + goto unlock; } - + ret = -EBADFD; if (!tun) - return -EBADFD; + goto unlock; DBG(KERN_INFO "%s: tun_chr_ioctl cmd %d\n", tun->dev->name, cmd); ret = 0; switch (cmd) { case TUNGETIFF: - ret = tun_get_iff(current->nsproxy->net_ns, file, &ifr); + ret = tun_get_iff(current->nsproxy->net_ns, tun, &ifr); if (ret) break; @@ -1201,7 +1194,6 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file, case TUNSETLINK: /* Only allow setting the type when the interface is down */ - rtnl_lock(); if (tun->dev->flags & IFF_UP) { DBG(KERN_INFO "%s: Linktype set failed because interface is up\n", tun->dev->name); @@ -1211,7 +1203,6 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file, DBG(KERN_INFO "%s: linktype set to %d\n", tun->dev->name, tun->dev->type); ret = 0; } - rtnl_unlock(); break; #ifdef TUN_DEBUG @@ -1220,9 +1211,7 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file, break; #endif case TUNSETOFFLOAD: - rtnl_lock(); ret = set_offload(tun->dev, arg); - rtnl_unlock(); break; case TUNSETTXFILTER: @@ -1230,9 +1219,7 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file, ret = -EINVAL; if ((tun->flags & TUN_TYPE_MASK) != TUN_TAP_DEV) break; - rtnl_lock(); ret = update_filter(&tun->txflt, (void __user *)arg); - rtnl_unlock(); break; case SIOCGIFHWADDR: @@ -1248,9 +1235,7 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file, DBG(KERN_DEBUG "%s: set hw address: %pM\n", tun->dev->name, ifr.ifr_hwaddr.sa_data); - rtnl_lock(); ret = dev_set_mac_address(tun->dev, &ifr.ifr_hwaddr); - rtnl_unlock(); break; case TUNGETSNDBUF: @@ -1273,7 +1258,10 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file, break; }; - tun_put(tun); +unlock: + rtnl_unlock(); + if (tun) + tun_put(tun); return ret; } @@ -1361,7 +1349,7 @@ static const struct file_operations tun_fops = { .write = do_sync_write, .aio_write = tun_chr_aio_write, .poll = tun_chr_poll, - .ioctl = tun_chr_ioctl, + .unlocked_ioctl = tun_chr_ioctl, .open = tun_chr_open, .release = tun_chr_close, .fasync = tun_chr_fasync -- GitLab From a6616b42fbc39c1ccc2373996f1441ce7707ea93 Mon Sep 17 00:00:00 2001 From: Yi Zou Date: Thu, 6 Aug 2009 13:05:23 +0000 Subject: [PATCH 0971/1342] ixgbe: Pass rx_ring directly in ixgbe_configure_srrctl() Instead of passing the register index of the corresponding rx_ring and find the way back to get to corresponding rx_ring in ixgbe_configure_srrctl(), simplify the function ixgbe_configure_srrctl() by passing the rx_ring into it. Then the register index for that rx_ring is already available from rx_ring->reg_idx. Signed-off-by: Yi Zou Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_main.c | 55 ++++++++++------------------------ 1 file changed, 15 insertions(+), 40 deletions(-) diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index 110c65ab5cb..e361b7f0101 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -1898,46 +1898,19 @@ static void ixgbe_configure_tx(struct ixgbe_adapter *adapter) #define IXGBE_SRRCTL_BSIZEHDRSIZE_SHIFT 2 -static void ixgbe_configure_srrctl(struct ixgbe_adapter *adapter, int index) +static void ixgbe_configure_srrctl(struct ixgbe_adapter *adapter, + struct ixgbe_ring *rx_ring) { - struct ixgbe_ring *rx_ring; u32 srrctl; - int queue0 = 0; - unsigned long mask; + int index; struct ixgbe_ring_feature *feature = adapter->ring_feature; - if (adapter->hw.mac.type == ixgbe_mac_82599EB) { - if (adapter->flags & IXGBE_FLAG_DCB_ENABLED) { - int dcb_i = feature[RING_F_DCB].indices; - if (dcb_i == 8) - queue0 = index >> 4; - else if (dcb_i == 4) - queue0 = index >> 5; - else - dev_err(&adapter->pdev->dev, "Invalid DCB " - "configuration\n"); -#ifdef IXGBE_FCOE - if (adapter->flags & IXGBE_FLAG_FCOE_ENABLED) { - struct ixgbe_ring_feature *f; - - rx_ring = &adapter->rx_ring[queue0]; - f = &adapter->ring_feature[RING_F_FCOE]; - if ((queue0 == 0) && (index > rx_ring->reg_idx)) - queue0 = f->mask + index - - rx_ring->reg_idx - 1; - } -#endif /* IXGBE_FCOE */ - } else { - queue0 = index; - } - } else { + index = rx_ring->reg_idx; + if (adapter->hw.mac.type == ixgbe_mac_82598EB) { + unsigned long mask; mask = (unsigned long) feature[RING_F_RSS].mask; - queue0 = index & mask; index = index & mask; } - - rx_ring = &adapter->rx_ring[queue0]; - srrctl = IXGBE_READ_REG(&adapter->hw, IXGBE_SRRCTL(index)); srrctl &= ~IXGBE_SRRCTL_BSIZEHDR_MASK; @@ -2002,6 +1975,7 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) { u64 rdba; struct ixgbe_hw *hw = &adapter->hw; + struct ixgbe_ring *rx_ring; struct net_device *netdev = adapter->netdev; int max_frame = netdev->mtu + ETH_HLEN + ETH_FCS_LEN; int i, j; @@ -2070,16 +2044,17 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) * the Base and Length of the Rx Descriptor Ring */ for (i = 0; i < adapter->num_rx_queues; i++) { - rdba = adapter->rx_ring[i].dma; - j = adapter->rx_ring[i].reg_idx; + rx_ring = &adapter->rx_ring[i]; + rdba = rx_ring->dma; + j = rx_ring->reg_idx; IXGBE_WRITE_REG(hw, IXGBE_RDBAL(j), (rdba & DMA_BIT_MASK(32))); IXGBE_WRITE_REG(hw, IXGBE_RDBAH(j), (rdba >> 32)); IXGBE_WRITE_REG(hw, IXGBE_RDLEN(j), rdlen); IXGBE_WRITE_REG(hw, IXGBE_RDH(j), 0); IXGBE_WRITE_REG(hw, IXGBE_RDT(j), 0); - adapter->rx_ring[i].head = IXGBE_RDH(j); - adapter->rx_ring[i].tail = IXGBE_RDT(j); - adapter->rx_ring[i].rx_buf_len = rx_buf_len; + rx_ring->head = IXGBE_RDH(j); + rx_ring->tail = IXGBE_RDT(j); + rx_ring->rx_buf_len = rx_buf_len; #ifdef IXGBE_FCOE if (adapter->flags & IXGBE_FLAG_FCOE_ENABLED) { @@ -2087,12 +2062,12 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) f = &adapter->ring_feature[RING_F_FCOE]; if ((rx_buf_len < IXGBE_FCOE_JUMBO_FRAME_SIZE) && (i >= f->mask) && (i < f->mask + f->indices)) - adapter->rx_ring[i].rx_buf_len = + rx_ring->rx_buf_len = IXGBE_FCOE_JUMBO_FRAME_SIZE; } #endif /* IXGBE_FCOE */ - ixgbe_configure_srrctl(adapter, j); + ixgbe_configure_srrctl(adapter, rx_ring); } if (hw->mac.type == ixgbe_mac_82598EB) { -- GitLab From 6e455b897bb6be3a4c0c6578f679e83d399e5b92 Mon Sep 17 00:00:00 2001 From: Yi Zou Date: Thu, 6 Aug 2009 13:05:44 +0000 Subject: [PATCH 0972/1342] ixgbe: Disable packet split only on FCoE queues in 82599 For 82599, packet split has to be disabled for FCoE direct data placement. However, this is only required on received queues allocated for FCoE. This patch adds a per ring flags to indicate if packet split is disabled on a per queue basis, particularly for FCoE, as packet split must be disabled for large receive using direct data placement (DDP). Signed-off-by: Yi Zou Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe.h | 2 ++ drivers/net/ixgbe/ixgbe_main.c | 33 +++++++++++++++++---------------- 2 files changed, 19 insertions(+), 16 deletions(-) diff --git a/drivers/net/ixgbe/ixgbe.h b/drivers/net/ixgbe/ixgbe.h index e11d83d5852..2c4dc8221dc 100644 --- a/drivers/net/ixgbe/ixgbe.h +++ b/drivers/net/ixgbe/ixgbe.h @@ -136,6 +136,8 @@ struct ixgbe_ring { u8 queue_index; /* needed for multiqueue queue management */ +#define IXGBE_RING_RX_PS_ENABLED (u8)(1) + u8 flags; /* per ring feature flags */ u16 head; u16 tail; diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index e361b7f0101..e3cb949b9aa 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -585,7 +585,7 @@ static void ixgbe_alloc_rx_buffers(struct ixgbe_adapter *adapter, rx_desc = IXGBE_RX_DESC_ADV(*rx_ring, i); if (!bi->page_dma && - (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED)) { + (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED)) { if (!bi->page) { bi->page = alloc_page(GFP_ATOMIC); if (!bi->page) { @@ -629,7 +629,7 @@ static void ixgbe_alloc_rx_buffers(struct ixgbe_adapter *adapter, } /* Refresh the desc even if buffer_addrs didn't change because * each write-back erases this info. */ - if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) { + if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) { rx_desc->read.pkt_addr = cpu_to_le64(bi->page_dma); rx_desc->read.hdr_addr = cpu_to_le64(bi->dma); } else { @@ -726,7 +726,7 @@ static bool ixgbe_clean_rx_irq(struct ixgbe_q_vector *q_vector, break; (*work_done)++; - if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) { + if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) { hdr_info = le16_to_cpu(ixgbe_get_hdr_info(rx_desc)); len = (hdr_info & IXGBE_RXDADV_HDRBUFLEN_MASK) >> IXGBE_RXDADV_HDRBUFLEN_SHIFT; @@ -798,7 +798,7 @@ static bool ixgbe_clean_rx_irq(struct ixgbe_q_vector *q_vector, rx_ring->stats.packets++; rx_ring->stats.bytes += skb->len; } else { - if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) { + if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) { rx_buffer_info->skb = next_buffer->skb; rx_buffer_info->dma = next_buffer->dma; next_buffer->skb = skb; @@ -1919,7 +1919,7 @@ static void ixgbe_configure_srrctl(struct ixgbe_adapter *adapter, srrctl |= (IXGBE_RX_HDR_SIZE << IXGBE_SRRCTL_BSIZEHDRSIZE_SHIFT) & IXGBE_SRRCTL_BSIZEHDR_MASK; - if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) { + if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) { #if (PAGE_SIZE / 2) > IXGBE_MAX_RXBUFFER srrctl |= IXGBE_MAX_RXBUFFER >> IXGBE_SRRCTL_BSIZEPKT_SHIFT; #else @@ -1992,11 +1992,6 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) /* Decide whether to use packet split mode or not */ adapter->flags |= IXGBE_FLAG_RX_PS_ENABLED; -#ifdef IXGBE_FCOE - if (adapter->flags & IXGBE_FLAG_FCOE_ENABLED) - adapter->flags &= ~IXGBE_FLAG_RX_PS_ENABLED; -#endif /* IXGBE_FCOE */ - /* Set the RX buffer length according to the mode */ if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) { rx_buf_len = IXGBE_RX_HDR_SIZE; @@ -2056,14 +2051,19 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) rx_ring->tail = IXGBE_RDT(j); rx_ring->rx_buf_len = rx_buf_len; + if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) + rx_ring->flags |= IXGBE_RING_RX_PS_ENABLED; + #ifdef IXGBE_FCOE if (adapter->flags & IXGBE_FLAG_FCOE_ENABLED) { struct ixgbe_ring_feature *f; f = &adapter->ring_feature[RING_F_FCOE]; - if ((rx_buf_len < IXGBE_FCOE_JUMBO_FRAME_SIZE) && - (i >= f->mask) && (i < f->mask + f->indices)) - rx_ring->rx_buf_len = - IXGBE_FCOE_JUMBO_FRAME_SIZE; + if ((i >= f->mask) && (i < f->mask + f->indices)) { + rx_ring->flags &= ~IXGBE_RING_RX_PS_ENABLED; + if (rx_buf_len < IXGBE_FCOE_JUMBO_FRAME_SIZE) + rx_ring->rx_buf_len = + IXGBE_FCOE_JUMBO_FRAME_SIZE; + } } #endif /* IXGBE_FCOE */ @@ -2143,7 +2143,8 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED) { /* Enable 82599 HW-RSC */ for (i = 0; i < adapter->num_rx_queues; i++) { - j = adapter->rx_ring[i].reg_idx; + rx_ring = &adapter->rx_ring[i]; + j = rx_ring->reg_idx; rscctrl = IXGBE_READ_REG(hw, IXGBE_RSCCTL(j)); rscctrl |= IXGBE_RSCCTL_RSCEN; /* @@ -2151,7 +2152,7 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) * total size of max desc * buf_len is not greater * than 65535 */ - if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) { + if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) { #if (MAX_SKB_FRAGS > 16) rscctrl |= IXGBE_RSCCTL_MAXDESC_16; #elif (MAX_SKB_FRAGS > 8) -- GitLab From 373a88d78be540c1331ea5adcb76610dddcb008b Mon Sep 17 00:00:00 2001 From: Bruce Allan Date: Fri, 7 Aug 2009 07:41:37 +0000 Subject: [PATCH 0973/1342] e1000e: fix acquisition of SW/FW/HW semaphore for ICHx parts For ICHx parts, write the EXTCNF_CTRL.SWFLAG bit once when trying to acquire the SW/FW/HW semaphore instead of multiple times to prevent the hardware from having problems (especially for systems with manageability enabled), and extend the timeout for the hardware to set the SWFLAG bit. Signed-off-by: Bruce Allan Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/e1000e/ich8lan.c | 44 +++++++++++++++++++++++++----------- 1 file changed, 31 insertions(+), 13 deletions(-) diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c index d56c7473144..dd61e7e98dd 100644 --- a/drivers/net/e1000e/ich8lan.c +++ b/drivers/net/e1000e/ich8lan.c @@ -594,8 +594,8 @@ static DEFINE_MUTEX(nvm_mutex); **/ static s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw) { - u32 extcnf_ctrl; - u32 timeout = PHY_CFG_TIMEOUT; + u32 extcnf_ctrl, timeout = PHY_CFG_TIMEOUT; + s32 ret_val = 0; might_sleep(); @@ -603,28 +603,46 @@ static s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw) while (timeout) { extcnf_ctrl = er32(EXTCNF_CTRL); + if (!(extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG)) + break; - if (!(extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG)) { - extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG; - ew32(EXTCNF_CTRL, extcnf_ctrl); + mdelay(1); + timeout--; + } + + if (!timeout) { + hw_dbg(hw, "SW/FW/HW has locked the resource for too long.\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + timeout = PHY_CFG_TIMEOUT * 2; + + extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG; + ew32(EXTCNF_CTRL, extcnf_ctrl); + + while (timeout) { + extcnf_ctrl = er32(EXTCNF_CTRL); + if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG) + break; - extcnf_ctrl = er32(EXTCNF_CTRL); - if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG) - break; - } mdelay(1); timeout--; } if (!timeout) { - hw_dbg(hw, "FW or HW has locked the resource for too long.\n"); + hw_dbg(hw, "Failed to acquire the semaphore.\n"); extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG; ew32(EXTCNF_CTRL, extcnf_ctrl); - mutex_unlock(&nvm_mutex); - return -E1000_ERR_CONFIG; + ret_val = -E1000_ERR_CONFIG; + goto out; } - return 0; +out: + if (ret_val) + mutex_unlock(&nvm_mutex); + + return ret_val; } /** -- GitLab From 148675a7b2061b5a5eb194530b7c4d8de1f2887e Mon Sep 17 00:00:00 2001 From: Bruce Allan Date: Fri, 7 Aug 2009 07:41:56 +0000 Subject: [PATCH 0974/1342] e1000e: fix potential NVM corruption on ICH9 with 8K bank size The bank offset was being incorrectly calculated on ICH9 parts with a bank size of 8K (instead of the more common 4K bank) which would cause any NVM writes to be done on the wrong address after switching from bank 1 to bank 0. Additionally, assume we are meant to use bank 0 if a valid bank is not detected, and remove the unnecessary acquisition of the SW/FW/HW semaphore when writing to the shadow ram version of the NVM image. Signed-off-by: Bruce Allan Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/e1000e/ich8lan.c | 50 +++++++++--------------------------- 1 file changed, 12 insertions(+), 38 deletions(-) diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c index dd61e7e98dd..99df2abf82a 100644 --- a/drivers/net/e1000e/ich8lan.c +++ b/drivers/net/e1000e/ich8lan.c @@ -338,10 +338,7 @@ static s32 e1000_init_nvm_params_ich8lan(struct e1000_hw *hw) { struct e1000_nvm_info *nvm = &hw->nvm; struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; - union ich8_hws_flash_status hsfsts; - u32 gfpreg; - u32 sector_base_addr; - u32 sector_end_addr; + u32 gfpreg, sector_base_addr, sector_end_addr; u16 i; /* Can't read flash registers if the register set isn't mapped. */ @@ -375,20 +372,6 @@ static s32 e1000_init_nvm_params_ich8lan(struct e1000_hw *hw) /* Adjust to word count */ nvm->flash_bank_size /= sizeof(u16); - /* - * Make sure the flash bank size does not overwrite the 4k - * sector ranges. We may have 64k allotted to us but we only care - * about the first 2 4k sectors. Therefore, if we have anything less - * than 64k set in the HSFSTS register, we will reduce the bank size - * down to 4k and let the rest remain unused. If berasesz == 3, then - * we are working in 64k mode. Otherwise we are not. - */ - if (nvm->flash_bank_size > E1000_ICH8_SHADOW_RAM_WORDS) { - hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); - if (hsfsts.hsf_status.berasesz != 3) - nvm->flash_bank_size = E1000_ICH8_SHADOW_RAM_WORDS; - } - nvm->word_size = E1000_ICH8_SHADOW_RAM_WORDS; /* Clear shadow ram */ @@ -1324,7 +1307,7 @@ static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, struct e1000_nvm_info *nvm = &hw->nvm; struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; u32 act_offset; - s32 ret_val; + s32 ret_val = 0; u32 bank = 0; u16 i, word; @@ -1339,12 +1322,15 @@ static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, goto out; ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank); - if (ret_val) - goto release; + if (ret_val) { + hw_dbg(hw, "Could not detect valid bank, assuming bank 0\n"); + bank = 0; + } act_offset = (bank) ? nvm->flash_bank_size : 0; act_offset += offset; + ret_val = 0; for (i = 0; i < words; i++) { if ((dev_spec->shadow_ram) && (dev_spec->shadow_ram[offset+i].modified)) { @@ -1359,7 +1345,6 @@ static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, } } -release: e1000_release_swflag_ich8lan(hw); out: @@ -1610,7 +1595,6 @@ static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, { struct e1000_nvm_info *nvm = &hw->nvm; struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; - s32 ret_val; u16 i; if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) || @@ -1619,17 +1603,11 @@ static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, return -E1000_ERR_NVM; } - ret_val = e1000_acquire_swflag_ich8lan(hw); - if (ret_val) - return ret_val; - for (i = 0; i < words; i++) { dev_spec->shadow_ram[offset+i].modified = 1; dev_spec->shadow_ram[offset+i].value = data[i]; } - e1000_release_swflag_ich8lan(hw); - return 0; } @@ -1670,8 +1648,8 @@ static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw) */ ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank); if (ret_val) { - e1000_release_swflag_ich8lan(hw); - goto out; + hw_dbg(hw, "Could not detect valid bank, assuming bank 0\n"); + bank = 0; } if (bank == 0) { @@ -2057,12 +2035,8 @@ static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank) iteration = 1; break; case 2: - if (hw->mac.type == e1000_ich9lan) { - sector_size = ICH_FLASH_SEG_SIZE_8K; - iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_8K; - } else { - return -E1000_ERR_NVM; - } + sector_size = ICH_FLASH_SEG_SIZE_8K; + iteration = 1; break; case 3: sector_size = ICH_FLASH_SEG_SIZE_64K; @@ -2074,7 +2048,7 @@ static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank) /* Start with the base address, then add the sector offset. */ flash_linear_addr = hw->nvm.flash_base_addr; - flash_linear_addr += (bank) ? (sector_size * iteration) : 0; + flash_linear_addr += (bank) ? flash_bank_size : 0; for (j = 0; j < iteration ; j++) { do { -- GitLab From 75c4885924f01aed1f887886a49dfa89960de240 Mon Sep 17 00:00:00 2001 From: Yong Zhang Date: Fri, 7 Aug 2009 16:36:52 +0000 Subject: [PATCH 0975/1342] gianfar: keep vlan related state when restart If vlan has been enabled. ifdown followed by ifup will lost hardware related state. Also remove duplicated operation in gfar_vlan_rx_register(). Signed-off-by: Yong Zhang Acked-by: Dai Haruki Signed-off-by: David S. Miller --- drivers/net/gianfar.c | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-) diff --git a/drivers/net/gianfar.c b/drivers/net/gianfar.c index f8ffcbf0bc3..e212f2c5448 100644 --- a/drivers/net/gianfar.c +++ b/drivers/net/gianfar.c @@ -936,6 +936,7 @@ int startup_gfar(struct net_device *dev) struct gfar __iomem *regs = priv->regs; int err = 0; u32 rctrl = 0; + u32 tctrl = 0; u32 attrs = 0; gfar_write(®s->imask, IMASK_INIT_CLEAR); @@ -1111,11 +1112,19 @@ int startup_gfar(struct net_device *dev) rctrl |= RCTRL_PADDING(priv->padding); } + /* keep vlan related bits if it's enabled */ + if (priv->vlgrp) { + rctrl |= RCTRL_VLEX | RCTRL_PRSDEP_INIT; + tctrl |= TCTRL_VLINS; + } + /* Init rctrl based on our settings */ gfar_write(&priv->regs->rctrl, rctrl); if (dev->features & NETIF_F_IP_CSUM) - gfar_write(&priv->regs->tctrl, TCTRL_INIT_CSUM); + tctrl |= TCTRL_INIT_CSUM; + + gfar_write(&priv->regs->tctrl, tctrl); /* Set the extraction length and index */ attrs = ATTRELI_EL(priv->rx_stash_size) | @@ -1450,7 +1459,6 @@ static void gfar_vlan_rx_register(struct net_device *dev, /* Enable VLAN tag extraction */ tempval = gfar_read(&priv->regs->rctrl); - tempval |= RCTRL_VLEX; tempval |= (RCTRL_VLEX | RCTRL_PRSDEP_INIT); gfar_write(&priv->regs->rctrl, tempval); } else { -- GitLab From 018d21ed80736eab21fabf45edbd74600a1f8330 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Fri, 7 Aug 2009 06:43:01 +0000 Subject: [PATCH 0976/1342] MAINTAINERS: additional NETWORKING [GENERAL] and NETWORKING DRIVERS patterns Signed-off-by: Joe Perches Signed-off-by: David S. Miller --- MAINTAINERS | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index fa76ad0a37e..aee67a88889 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -3555,6 +3555,9 @@ T: git git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.git S: Maintained F: net/ F: include/net/ +F: include/linux/in.h +F: include/linux/net.h +F: include/linux/netdevice.h NETWORKING [IPv4/IPv6] M: "David S. Miller" @@ -3590,6 +3593,8 @@ W: http://www.linuxfoundation.org/en/Net T: git git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.git S: Odd Fixes F: drivers/net/ +F: include/linux/if_* +F: include/linux/*device.h NETXEN (1/10) GbE SUPPORT M: Dhananjay Phadke -- GitLab From 418372b0ab7a3bbcc59d71e8e4d322ef18263dab Mon Sep 17 00:00:00 2001 From: Rafael Laufer Date: Fri, 7 Aug 2009 05:17:17 +0000 Subject: [PATCH 0977/1342] sctp: fix missing destroy of percpu counter variable in sctp_proc_exit() Commit 1748376b6626acf59c24e9592ac67b3fe2a0e026, net: Use a percpu_counter for sockets_allocated added percpu_counter function calls to sctp_proc_init code path, but forgot to add them to sctp_proc_exit(). This resulted in a following Ooops when performing this test # modprobe sctp # rmmod -f sctp # modprobe sctp [ 573.862512] BUG: unable to handle kernel paging request at f8214a24 [ 573.862518] IP: [] __percpu_counter_init+0x3f/0x70 [ 573.862530] *pde = 37010067 *pte = 00000000 [ 573.862534] Oops: 0002 [#1] SMP [ 573.862537] last sysfs file: /sys/module/libcrc32c/initstate [ 573.862540] Modules linked in: sctp(+) crc32c libcrc32c binfmt_misc bridge stp bnep lp snd_hda_codec_analog snd_hda_intel snd_hda_codec snd_hwdep snd_pcm_oss snd_mixer_oss arc4 joydev snd_pcm ecb pcmcia snd_seq_dummy snd_seq_oss iwlagn iwlcore snd_seq_midi snd_rawmidi snd_seq_midi_event yenta_socket rsrc_nonstatic thinkpad_acpi snd_seq snd_timer snd_seq_device mac80211 psmouse sdhci_pci sdhci nvidia(P) ppdev video snd soundcore serio_raw pcspkr iTCO_wdt iTCO_vendor_support led_class ricoh_mmc pcmcia_core intel_agp nvram agpgart usbhid parport_pc parport output snd_page_alloc cfg80211 btusb ohci1394 ieee1394 e1000e [last unloaded: sctp] [ 573.862589] [ 573.862593] Pid: 5373, comm: modprobe Tainted: P R (2.6.31-rc3 #6) 7663B15 [ 573.862596] EIP: 0060:[] EFLAGS: 00010286 CPU: 1 [ 573.862599] EIP is at __percpu_counter_init+0x3f/0x70 [ 573.862602] EAX: f8214a20 EBX: f80faa14 ECX: c48c0000 EDX: f80faa20 [ 573.862604] ESI: f80a7000 EDI: 00000000 EBP: f69d5ef0 ESP: f69d5eec [ 573.862606] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 [ 573.862610] Process modprobe (pid: 5373, ti=f69d4000 task=c2130c70 task.ti=f69d4000) [ 573.862612] Stack: [ 573.862613] 00000000 f69d5f18 f80a70a8 f80fa9fc 00000000 fffffffc f69d5f30 c018e2d4 [ 573.862619] <0> 00000000 f80a7000 00000000 f69d5f88 c010112b 00000000 c07029c0 fffffffb [ 573.862626] <0> 00000000 f69d5f38 c018f83f f69d5f54 c0557cad f80fa860 00000001 c07010c0 [ 573.862634] Call Trace: [ 573.862644] [] ? sctp_init+0xa8/0x7d4 [sctp] [ 573.862650] [] ? marker_update_probe_range+0x184/0x260 [ 573.862659] [] ? sctp_init+0x0/0x7d4 [sctp] [ 573.862662] [] ? do_one_initcall+0x2b/0x160 [ 573.862666] [] ? tracepoint_module_notify+0x2f/0x40 [ 573.862671] [] ? notifier_call_chain+0x2d/0x70 [ 573.862678] [] ? __blocking_notifier_call_chain+0x4d/0x60 [ 573.862682] [] ? sys_init_module+0xb1/0x1f0 [ 573.862686] [] ? sysenter_do_call+0x12/0x28 [ 573.862688] Code: 89 48 08 b8 04 00 00 00 e8 df aa ec ff ba f4 ff ff ff 85 c0 89 43 14 74 31 b8 b0 18 71 c0 e8 19 b9 24 00 a1 c4 18 71 c0 8d 53 0c <89> 50 04 89 43 0c b8 b0 18 71 c0 c7 43 10 c4 18 71 c0 89 15 c4 [ 573.862725] EIP: [] __percpu_counter_init+0x3f/0x70 SS:ESP 0068:f69d5eec [ 573.862730] CR2: 00000000f8214a24 [ 573.862734] ---[ end trace 39c4e0b55e7cf54d ]--- Signed-off-by: Rafael Laufer Signed-off-by: Vlad Yasevich Signed-off-by: David S. Miller --- net/sctp/protocol.c | 1 + 1 file changed, 1 insertion(+) diff --git a/net/sctp/protocol.c b/net/sctp/protocol.c index 79cbd47f4df..a76da657244 100644 --- a/net/sctp/protocol.c +++ b/net/sctp/protocol.c @@ -160,6 +160,7 @@ static void sctp_proc_exit(void) remove_proc_entry("sctp", init_net.proc_net); } #endif + percpu_counter_destroy(&sctp_sockets_allocated); } /* Private helper to extract ipv4 address and stash them in -- GitLab From 5e33b719c8fcccfedc1d25167826a0f93fe6c5a1 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Fri, 7 Aug 2009 03:24:27 +0000 Subject: [PATCH 0978/1342] pcnet32: Read buffer overflow An `options[cards_found]' that equals `sizeof(options_mapping)' is already beyond the array. Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/pcnet32.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/pcnet32.c b/drivers/net/pcnet32.c index a646a445fda..23e1a0750fe 100644 --- a/drivers/net/pcnet32.c +++ b/drivers/net/pcnet32.c @@ -1839,7 +1839,7 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) lp->chip_version = chip_version; lp->msg_enable = pcnet32_debug; if ((cards_found >= MAX_UNITS) - || (options[cards_found] > sizeof(options_mapping))) + || (options[cards_found] >= sizeof(options_mapping))) lp->options = PCNET32_PORT_ASEL; else lp->options = options_mapping[options[cards_found]]; -- GitLab From be12159b24c532b4b48bdec5a543336438faa132 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Sun, 9 Aug 2009 04:00:25 +0000 Subject: [PATCH 0979/1342] zorro8390: Fix read buffer overflow in zorro8390_init_one() Prevent read from cards[-1] when no card was found. Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/zorro8390.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/net/zorro8390.c b/drivers/net/zorro8390.c index 37c84e3b8be..81c753a617a 100644 --- a/drivers/net/zorro8390.c +++ b/drivers/net/zorro8390.c @@ -120,6 +120,9 @@ static int __devinit zorro8390_init_one(struct zorro_dev *z, for (i = ARRAY_SIZE(cards)-1; i >= 0; i--) if (z->id == cards[i].id) break; + if (i < 0) + return -ENODEV; + board = z->resource.start; ioaddr = board+cards[i].offset; dev = alloc_ei_netdev(); -- GitLab From 973507cb8610d4c84f090d5f1f0ca54fa0559d27 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Sat, 8 Aug 2009 23:54:21 +0000 Subject: [PATCH 0980/1342] mlx4_en: Fix read buffer overflow in mlx4_en_complete_rx_desc() If the length is less or equal to frag_prefix_size in the first iteration we write skb_frags_rx[-1] and read from priv->frag_info[-1] Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/mlx4/en_rx.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/net/mlx4/en_rx.c b/drivers/net/mlx4/en_rx.c index 91bdfdfd431..3ac0404d0d1 100644 --- a/drivers/net/mlx4/en_rx.c +++ b/drivers/net/mlx4/en_rx.c @@ -506,8 +506,9 @@ static int mlx4_en_complete_rx_desc(struct mlx4_en_priv *priv, PCI_DMA_FROMDEVICE); } /* Adjust size of last fragment to match actual length */ - skb_frags_rx[nr - 1].size = length - - priv->frag_info[nr - 1].frag_prefix_size; + if (nr > 0) + skb_frags_rx[nr - 1].size = length - + priv->frag_info[nr - 1].frag_prefix_size; return nr; fail: -- GitLab From b2f2e8fee3d62f621e795f25b2fc0f51bbdb4af9 Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Mon, 10 Aug 2009 16:36:38 +1000 Subject: [PATCH 0981/1342] powerpc/dma: pci_set_dma_mask() shouldn't fail if mask fits in RAM On an iMac G5, the b43 driver is failing to initialise because trying to set the dma mask to 30-bit fails. Even though there's only 512MiB of RAM in the machine anyway: https://bugzilla.redhat.com/show_bug.cgi?id=514787 We should probably let it succeed if the available RAM in the system doesn't exceed the requested limit. Signed-off-by: David Woodhouse Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/dma.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/powerpc/kernel/dma.c b/arch/powerpc/kernel/dma.c index 20a60d661ba..ccf129d47d8 100644 --- a/arch/powerpc/kernel/dma.c +++ b/arch/powerpc/kernel/dma.c @@ -7,6 +7,7 @@ #include #include +#include #include #include @@ -90,11 +91,10 @@ static void dma_direct_unmap_sg(struct device *dev, struct scatterlist *sg, static int dma_direct_dma_supported(struct device *dev, u64 mask) { #ifdef CONFIG_PPC64 - /* Could be improved to check for memory though it better be - * done via some global so platforms can set the limit in case + /* Could be improved so platforms can set the limit in case * they have limited DMA windows */ - return mask >= DMA_BIT_MASK(32); + return mask >= (lmb_end_of_DRAM() - 1); #else return 1; #endif -- GitLab From beda2c7ea2c15ed01eef00a997d2b0496c3a502d Mon Sep 17 00:00:00 2001 From: Darren Hart Date: Sun, 9 Aug 2009 15:34:39 -0700 Subject: [PATCH 0982/1342] futex: Update futex_q lock_ptr on requeue proxy lock futex_requeue() can acquire the lock on behalf of a waiter early on or during the requeue loop if it is uncontended or in the event of a lock steal or owner died. On wakeup, the waiter (in futex_wait_requeue_pi()) cleans up the pi_state owner using the lock_ptr to protect against concurrent access to the pi_state. The pi_state is hung off futex_q's on the requeue target futex hash bucket so the lock_ptr needs to be updated accordingly. The problem manifested by triggering the WARN_ON in lookup_pi_state() about the pid != pi_state->owner->pid. With this patch, the pi_state is properly guarded against concurrent access via the requeue target hb lock. The astute reviewer may notice that there is a window of time between when futex_requeue() unlocks the hb locks and when futex_wait_requeue_pi() will acquire hb2->lock. During this time the pi_state and uval are not in sync with the underlying rtmutex owner (but the uval does indicate there are waiters, so no atomic changes will occur in userspace). However, this is not a problem. Should a contending thread enter lookup_pi_state() and acquire hb2->lock before the ownership is fixed up, it will find the pi_state hung off a waiter's (possibly the pending owner's) futex_q and block on the rtmutex. Once futex_wait_requeue_pi() fixes up the owner, it will also move the pi_state from the old owner's task->pi_state_list to its own. v3: Fix plist lock name for application to mainline (rather than -rt) Compile tested against tip/v2.6.31-rc5. Signed-off-by: Darren Hart Cc: Peter Zijlstra Cc: Steven Rostedt Cc: Eric Dumazet Cc: Dinakar Guniguntala Cc: John Stultz LKML-Reference: <4A7F4EFF.6090903@us.ibm.com> Signed-off-by: Ingo Molnar --- kernel/futex.c | 17 +++++++++++++---- 1 file changed, 13 insertions(+), 4 deletions(-) diff --git a/kernel/futex.c b/kernel/futex.c index 0672ff88f15..8cc3ee1363a 100644 --- a/kernel/futex.c +++ b/kernel/futex.c @@ -1010,15 +1010,19 @@ void requeue_futex(struct futex_q *q, struct futex_hash_bucket *hb1, * requeue_pi_wake_futex() - Wake a task that acquired the lock during requeue * q: the futex_q * key: the key of the requeue target futex + * hb: the hash_bucket of the requeue target futex * * During futex_requeue, with requeue_pi=1, it is possible to acquire the * target futex if it is uncontended or via a lock steal. Set the futex_q key * to the requeue target futex so the waiter can detect the wakeup on the right * futex, but remove it from the hb and NULL the rt_waiter so it can detect - * atomic lock acquisition. Must be called with the q->lock_ptr held. + * atomic lock acquisition. Set the q->lock_ptr to the requeue target hb->lock + * to protect access to the pi_state to fixup the owner later. Must be called + * with both q->lock_ptr and hb->lock held. */ static inline -void requeue_pi_wake_futex(struct futex_q *q, union futex_key *key) +void requeue_pi_wake_futex(struct futex_q *q, union futex_key *key, + struct futex_hash_bucket *hb) { drop_futex_key_refs(&q->key); get_futex_key_refs(key); @@ -1030,6 +1034,11 @@ void requeue_pi_wake_futex(struct futex_q *q, union futex_key *key) WARN_ON(!q->rt_waiter); q->rt_waiter = NULL; + q->lock_ptr = &hb->lock; +#ifdef CONFIG_DEBUG_PI_LIST + q->list.plist.lock = &hb->lock; +#endif + wake_up_state(q->task, TASK_NORMAL); } @@ -1088,7 +1097,7 @@ static int futex_proxy_trylock_atomic(u32 __user *pifutex, ret = futex_lock_pi_atomic(pifutex, hb2, key2, ps, top_waiter->task, set_waiters); if (ret == 1) - requeue_pi_wake_futex(top_waiter, key2); + requeue_pi_wake_futex(top_waiter, key2, hb2); return ret; } @@ -1273,7 +1282,7 @@ retry_private: this->task, 1); if (ret == 1) { /* We got the lock. */ - requeue_pi_wake_futex(this, &key2); + requeue_pi_wake_futex(this, &key2, hb2); continue; } else if (ret) { /* -EDEADLK */ -- GitLab From a044560c3a1f0ad75ce685c1ed7604820b9ed319 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Mon, 10 Aug 2009 11:16:52 +0200 Subject: [PATCH 0983/1342] perf_counter: Correct PERF_SAMPLE_RAW output PERF_SAMPLE_* output switches should unconditionally output the correct format, as they are the only way to unambiguously parse the PERF_EVENT_SAMPLE data. Signed-off-by: Peter Zijlstra Acked-by: Frederic Weisbecker Cc: Arnaldo Carvalho de Melo Cc: Mike Galbraith Cc: Paul Mackerras LKML-Reference: <1249896447.17467.74.camel@twins> Signed-off-by: Ingo Molnar --- include/linux/perf_counter.h | 2 ++ include/trace/ftrace.h | 3 ++- kernel/perf_counter.c | 30 ++++++++++++++++++++++++------ 3 files changed, 28 insertions(+), 7 deletions(-) diff --git a/include/linux/perf_counter.h b/include/linux/perf_counter.h index 2aabe43c1d0..a9d823a93fe 100644 --- a/include/linux/perf_counter.h +++ b/include/linux/perf_counter.h @@ -369,6 +369,8 @@ enum perf_event_type { * * { u64 nr, * u64 ips[nr]; } && PERF_SAMPLE_CALLCHAIN + * { u32 size; + * char data[size];}&& PERF_SAMPLE_RAW * }; */ PERF_EVENT_SAMPLE = 9, diff --git a/include/trace/ftrace.h b/include/trace/ftrace.h index 7fb16d90e7b..7167b9b97da 100644 --- a/include/trace/ftrace.h +++ b/include/trace/ftrace.h @@ -685,7 +685,8 @@ static void ftrace_profile_##call(proto) \ pc = preempt_count(); \ \ __data_size = ftrace_get_offsets_##call(&__data_offsets, args); \ - __entry_size = ALIGN(__data_size + sizeof(*entry), sizeof(u64));\ + __entry_size = ALIGN(__data_size + sizeof(*entry) + sizeof(u32),\ + sizeof(u64)); \ \ do { \ char raw_data[__entry_size]; \ diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index 546e62d6294..5229d1666fa 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -2646,7 +2646,6 @@ static void perf_counter_output(struct perf_counter *counter, int nmi, u64 counter; } group_entry; struct perf_callchain_entry *callchain = NULL; - struct perf_raw_record *raw = NULL; int callchain_size = 0; u64 time; struct { @@ -2716,9 +2715,15 @@ static void perf_counter_output(struct perf_counter *counter, int nmi, } if (sample_type & PERF_SAMPLE_RAW) { - raw = data->raw; - if (raw) - header.size += raw->size; + int size = sizeof(u32); + + if (data->raw) + size += data->raw->size; + else + size += sizeof(u32); + + WARN_ON_ONCE(size & (sizeof(u64)-1)); + header.size += size; } ret = perf_output_begin(&handle, counter, header.size, nmi, 1); @@ -2784,8 +2789,21 @@ static void perf_counter_output(struct perf_counter *counter, int nmi, } } - if ((sample_type & PERF_SAMPLE_RAW) && raw) - perf_output_copy(&handle, raw->data, raw->size); + if (sample_type & PERF_SAMPLE_RAW) { + if (data->raw) { + perf_output_put(&handle, data->raw->size); + perf_output_copy(&handle, data->raw->data, data->raw->size); + } else { + struct { + u32 size; + u32 data; + } raw = { + .size = sizeof(u32), + .data = 0, + }; + perf_output_put(&handle, raw); + } + } perf_output_end(&handle); } -- GitLab From a4e95fc2cbb31d70a65beffeaf8773f881328c34 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Mon, 10 Aug 2009 11:20:12 +0200 Subject: [PATCH 0984/1342] perf_counter: Require CAP_SYS_ADMIN for raw tracepoint data Raw tracepoint data contains various kernel internals and data from other users, so restrict this to CAP_SYS_ADMIN. Signed-off-by: Peter Zijlstra Acked-by: Frederic Weisbecker Cc: Arnaldo Carvalho de Melo Cc: Mike Galbraith Cc: Paul Mackerras LKML-Reference: <1249896452.17467.75.camel@twins> Signed-off-by: Ingo Molnar --- kernel/perf_counter.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index 5229d1666fa..b0b20a07f39 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -3787,6 +3787,14 @@ static void tp_perf_counter_destroy(struct perf_counter *counter) static const struct pmu *tp_perf_counter_init(struct perf_counter *counter) { + /* + * Raw tracepoint data is a severe data leak, only allow root to + * have these. + */ + if ((counter->attr.sample_type & PERF_SAMPLE_RAW) && + !capable(CAP_SYS_ADMIN)) + return ERR_PTR(-EPERM); + if (ftrace_profile_enable(counter->attr.config)) return NULL; -- GitLab From 100d5eb36ba20dc0b99a17ea2b9800c567bfc3d1 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Mon, 10 Aug 2009 11:55:51 +0200 Subject: [PATCH 0985/1342] ALSA: hda - Add missing vmaster initialization for ALC269 Without the initialization of vmaster NID, the dB information got confused for ALC269 codec. Reference: Novell bnc#527361 https://bugzilla.novell.com/show_bug.cgi?id=527361 Signed-off-by: Takashi Iwai Cc: --- sound/pci/hda/patch_realtek.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 51c44fdbc0f..5cc927f4783 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -13563,6 +13563,8 @@ static int patch_alc269(struct hda_codec *codec) set_capture_mixer(spec); set_beep_amp(spec, 0x0b, 0x04, HDA_INPUT); + spec->vmaster_nid = 0x02; + codec->patch_ops = alc_patch_ops; if (board_config == ALC269_AUTO) spec->init_hook = alc269_auto_init; -- GitLab From 13f0feafa6b8aead57a2a328e2fca6a5828bf286 Mon Sep 17 00:00:00 2001 From: Oleg Nesterov Date: Tue, 23 Jun 2009 21:25:32 +0200 Subject: [PATCH 0986/1342] mm_for_maps: simplify, use ptrace_may_access() It would be nice to kill __ptrace_may_access(). It requires task_lock(), but this lock is only needed to read mm->flags in the middle. Convert mm_for_maps() to use ptrace_may_access(), this also simplifies the code a little bit. Also, we do not need to take ->mmap_sem in advance. In fact I think mm_for_maps() should not play with ->mmap_sem at all, the caller should take this lock. With or without this patch, without ->cred_guard_mutex held we can race with exec() and get the new ->mm but check old creds. Signed-off-by: Oleg Nesterov Reviewed-by: Serge Hallyn Signed-off-by: James Morris --- fs/proc/base.c | 23 +++++++++++------------ 1 file changed, 11 insertions(+), 12 deletions(-) diff --git a/fs/proc/base.c b/fs/proc/base.c index 3ce5ae9e3d2..917f338a673 100644 --- a/fs/proc/base.c +++ b/fs/proc/base.c @@ -237,20 +237,19 @@ struct mm_struct *mm_for_maps(struct task_struct *task) struct mm_struct *mm = get_task_mm(task); if (!mm) return NULL; + if (mm != current->mm) { + /* + * task->mm can be changed before security check, + * in that case we must notice the change after. + */ + if (!ptrace_may_access(task, PTRACE_MODE_READ) || + mm != task->mm) { + mmput(mm); + return NULL; + } + } down_read(&mm->mmap_sem); - task_lock(task); - if (task->mm != mm) - goto out; - if (task->mm != current->mm && - __ptrace_may_access(task, PTRACE_MODE_READ) < 0) - goto out; - task_unlock(task); return mm; -out: - task_unlock(task); - up_read(&mm->mmap_sem); - mmput(mm); - return NULL; } static int proc_pid_cmdline(struct task_struct *task, char * buffer) -- GitLab From 00f89d218523b9bf6b522349c039d5ac80aa536d Mon Sep 17 00:00:00 2001 From: Oleg Nesterov Date: Fri, 10 Jul 2009 03:27:38 +0200 Subject: [PATCH 0987/1342] mm_for_maps: shift down_read(mmap_sem) to the caller mm_for_maps() takes ->mmap_sem after security checks, this looks strange and obfuscates the locking rules. Move this lock to its single caller, m_start(). Signed-off-by: Oleg Nesterov Acked-by: Serge Hallyn Signed-off-by: James Morris --- fs/proc/base.c | 8 +++----- fs/proc/task_mmu.c | 1 + fs/proc/task_nommu.c | 1 + 3 files changed, 5 insertions(+), 5 deletions(-) diff --git a/fs/proc/base.c b/fs/proc/base.c index 917f338a673..f3c2e4085fe 100644 --- a/fs/proc/base.c +++ b/fs/proc/base.c @@ -235,9 +235,8 @@ static int check_mem_permission(struct task_struct *task) struct mm_struct *mm_for_maps(struct task_struct *task) { struct mm_struct *mm = get_task_mm(task); - if (!mm) - return NULL; - if (mm != current->mm) { + + if (mm && mm != current->mm) { /* * task->mm can be changed before security check, * in that case we must notice the change after. @@ -245,10 +244,9 @@ struct mm_struct *mm_for_maps(struct task_struct *task) if (!ptrace_may_access(task, PTRACE_MODE_READ) || mm != task->mm) { mmput(mm); - return NULL; + mm = NULL; } } - down_read(&mm->mmap_sem); return mm; } diff --git a/fs/proc/task_mmu.c b/fs/proc/task_mmu.c index 6f61b7cc32e..9bd8be1d235 100644 --- a/fs/proc/task_mmu.c +++ b/fs/proc/task_mmu.c @@ -119,6 +119,7 @@ static void *m_start(struct seq_file *m, loff_t *pos) mm = mm_for_maps(priv->task); if (!mm) return NULL; + down_read(&mm->mmap_sem); tail_vma = get_gate_vma(priv->task); priv->tail_vma = tail_vma; diff --git a/fs/proc/task_nommu.c b/fs/proc/task_nommu.c index 64a72e2e765..8f5c05d3dbd 100644 --- a/fs/proc/task_nommu.c +++ b/fs/proc/task_nommu.c @@ -189,6 +189,7 @@ static void *m_start(struct seq_file *m, loff_t *pos) priv->task = NULL; return NULL; } + down_read(&mm->mmap_sem); /* start from the Nth VMA */ for (p = rb_first(&mm->mm_rb); p; p = rb_next(p)) -- GitLab From 704b836cbf19e885f8366bccb2e4b0474346c02d Mon Sep 17 00:00:00 2001 From: Oleg Nesterov Date: Fri, 10 Jul 2009 03:27:40 +0200 Subject: [PATCH 0988/1342] mm_for_maps: take ->cred_guard_mutex to fix the race with exec The problem is minor, but without ->cred_guard_mutex held we can race with exec() and get the new ->mm but check old creds. Now we do not need to re-check task->mm after ptrace_may_access(), it can't be changed to the new mm under us. Strictly speaking, this also fixes another very minor problem. Unless security check fails or the task exits mm_for_maps() should never return NULL, the caller should get either old or new ->mm. Signed-off-by: Oleg Nesterov Acked-by: Serge Hallyn Signed-off-by: James Morris --- fs/proc/base.c | 22 +++++++++++----------- 1 file changed, 11 insertions(+), 11 deletions(-) diff --git a/fs/proc/base.c b/fs/proc/base.c index f3c2e4085fe..175db258942 100644 --- a/fs/proc/base.c +++ b/fs/proc/base.c @@ -234,19 +234,19 @@ static int check_mem_permission(struct task_struct *task) struct mm_struct *mm_for_maps(struct task_struct *task) { - struct mm_struct *mm = get_task_mm(task); + struct mm_struct *mm; - if (mm && mm != current->mm) { - /* - * task->mm can be changed before security check, - * in that case we must notice the change after. - */ - if (!ptrace_may_access(task, PTRACE_MODE_READ) || - mm != task->mm) { - mmput(mm); - mm = NULL; - } + if (mutex_lock_killable(&task->cred_guard_mutex)) + return NULL; + + mm = get_task_mm(task); + if (mm && mm != current->mm && + !ptrace_may_access(task, PTRACE_MODE_READ)) { + mmput(mm); + mm = NULL; } + mutex_unlock(&task->cred_guard_mutex); + return mm; } -- GitLab From cd92204924fafbd5c7241dfd12ca3176d542e0c5 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 10 Aug 2009 14:49:50 +0300 Subject: [PATCH 0989/1342] OMAP: Fix testing of cpu defines for mach-omap1 There's no need to keep these defines limited in the ifdef block for mach-omap2. It will just cause problems testing for the CPU revision in the common code, like the next patch does for the DMA errata. Signed-off-by: Tony Lindgren --- arch/arm/plat-omap/include/mach/cpu.h | 5 ----- 1 file changed, 5 deletions(-) diff --git a/arch/arm/plat-omap/include/mach/cpu.h b/arch/arm/plat-omap/include/mach/cpu.h index 285eaa3a827..11e73d9e892 100644 --- a/arch/arm/plat-omap/include/mach/cpu.h +++ b/arch/arm/plat-omap/include/mach/cpu.h @@ -378,9 +378,6 @@ IS_OMAP_TYPE(3430, 0x3430) #define cpu_class_is_omap2() (cpu_is_omap24xx() || cpu_is_omap34xx() || \ cpu_is_omap44xx()) -#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) || \ - defined(CONFIG_ARCH_OMAP4) - /* Various silicon revisions for omap2 */ #define OMAP242X_CLASS 0x24200024 #define OMAP2420_REV_ES1_0 0x24200024 @@ -436,5 +433,3 @@ IS_OMAP_TYPE(3430, 0x3430) int omap_chip_is(struct omap_chip_id oci); void omap2_check_revision(void); - -#endif /* defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) */ -- GitLab From 284119c48f4a0c469b3e0237b500e536b4bc7b6f Mon Sep 17 00:00:00 2001 From: Vikram Pandita Date: Mon, 10 Aug 2009 14:49:50 +0300 Subject: [PATCH 0990/1342] OMAP2/3: DMA errata correction This errata is valid for: OMAP2420 Errata 1.85 Impacts all 2420 ES rev OMAP2430 Errata 1.10 Impacts only ES1.0 Description: DMA may hang when several channels are used in parallel OMAP3430: Not impacted, so remove the errata fix for omap3 Fixed issue reported on cpu_is_omap24xx check reported by Nishant Kamat Signed-off-by: Vikram Pandita Reviewed-by: Nishant Kamat Signed-off-by: Tony Lindgren --- arch/arm/plat-omap/dma.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/arch/arm/plat-omap/dma.c b/arch/arm/plat-omap/dma.c index 7677a4a1cef..e3ac94f0900 100644 --- a/arch/arm/plat-omap/dma.c +++ b/arch/arm/plat-omap/dma.c @@ -946,7 +946,9 @@ void omap_start_dma(int lch) cur_lch = next_lch; } while (next_lch != -1); - } else if (cpu_class_is_omap2()) { + } else if (cpu_is_omap242x() || + (cpu_is_omap243x() && omap_type() <= OMAP2430_REV_ES1_0)) { + /* Errata: Need to write lch even if not using chaining */ dma_write(lch, CLNK_CTRL(lch)); } -- GitLab From 370bc1fdefb8a30018d98aca2fdfd6b6701082e7 Mon Sep 17 00:00:00 2001 From: Janboe Ye Date: Mon, 10 Aug 2009 14:49:50 +0300 Subject: [PATCH 0991/1342] OMAP3: Fix omap3 sram virtual addres overlap vmalloc space after increasing vmalloc size commit e85c205ac1427f2405021a36f083280ff0d0a35e increase vmalloc size. vmalloc space will overlap with OMAP3 sram virtual address. Signed-off-by: Li Hong Mei Signed-off-by: Janboe Ye Reviewed-by: Paul Walmsley --- arch/arm/plat-omap/sram.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c index 4ea73804d21..2890b11f238 100644 --- a/arch/arm/plat-omap/sram.c +++ b/arch/arm/plat-omap/sram.c @@ -44,9 +44,9 @@ #define OMAP2_SRAM_VA 0xe3000000 #define OMAP2_SRAM_PUB_VA (OMAP2_SRAM_VA + 0x800) #define OMAP3_SRAM_PA 0x40200000 -#define OMAP3_SRAM_VA 0xd7000000 +#define OMAP3_SRAM_VA 0xe3000000 #define OMAP3_SRAM_PUB_PA 0x40208000 -#define OMAP3_SRAM_PUB_VA 0xd7008000 +#define OMAP3_SRAM_PUB_VA (OMAP3_SRAM_VA + 0x8000) #define OMAP4_SRAM_PA 0x40200000 /*0x402f0000*/ #define OMAP4_SRAM_VA 0xd7000000 /*0xd70f0000*/ -- GitLab From 5032902c331acc71956e47abd90d090181c5ef4a Mon Sep 17 00:00:00 2001 From: Sergio Aguirre Date: Mon, 10 Aug 2009 14:49:50 +0300 Subject: [PATCH 0992/1342] OMAP3: Overo: Fix smsc911x platform device resource value Fixes a wrong setting of resource parameter list in SMSC911x platform driver data structure for Overo case. This fixes folowing warning when compiling for Overo board: warning: initialization from incompatible pointer type Introduced since commit id: commit 172ef275444efa12d834fb9d1b1acdac92db47f7 Author: Steve Sakoman Date: Mon Feb 2 06:27:49 2009 +0000 ARM: Add SMSC911X support to Overo platform (V2) Signed-off-by: Sergio Aguirre Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-overo.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index dff5528fbfb..fec1bb19b9f 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -146,7 +146,7 @@ static struct platform_device overo_smsc911x_device = { .name = "smsc911x", .id = -1, .num_resources = ARRAY_SIZE(overo_smsc911x_resources), - .resource = &overo_smsc911x_resources, + .resource = overo_smsc911x_resources, .dev = { .platform_data = &overo_smsc911x_config, }, -- GitLab From dfc27b34496923b5f552eb9cdf20468045114ada Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Mon, 10 Aug 2009 14:49:51 +0300 Subject: [PATCH 0993/1342] OMAP3: RX51: Define TWL4030 USB transceiver in board file Add OTG transceiver to RX51 platform data to prevent kernel NULL pointer dereference during MUSB initialisation. Signed-off-by: Roger Quadros Signed-off-by: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-rx51-peripherals.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c index 9a0bf6744a0..56d931a425f 100644 --- a/arch/arm/mach-omap2/board-rx51-peripherals.c +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c @@ -278,6 +278,10 @@ static struct twl4030_gpio_platform_data rx51_gpio_data = { .setup = rx51_twlgpio_setup, }; +static struct twl4030_usb_data rx51_usb_data = { + .usb_mode = T2_USB_MODE_ULPI, +}; + static struct twl4030_platform_data rx51_twldata = { .irq_base = TWL4030_IRQ_BASE, .irq_end = TWL4030_IRQ_END, @@ -286,6 +290,7 @@ static struct twl4030_platform_data rx51_twldata = { .gpio = &rx51_gpio_data, .keypad = &rx51_kp_data, .madc = &rx51_madc_data, + .usb = &rx51_usb_data, .vaux1 = &rx51_vaux1, .vaux2 = &rx51_vaux2, -- GitLab From 22833044fbe2764d44ae03f58508e671652ca186 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Mon, 10 Aug 2009 14:49:51 +0300 Subject: [PATCH 0994/1342] OMAP2/3: mmc-twl4030: Free up MMC regulators while cleaning up twl_mmc_cleanup() must free up the regulators that were allocated by twl_mmc_late_init(). This eliminates the below error when 'omap_hsmmc' module is repeatedly loaded and unloaded. "sysfs: cannot create duplicate filename '/devices/platform /mmci-omap-hs.0/microamps_requested_vmmc'" Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/mmc-twl4030.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/mach-omap2/mmc-twl4030.c b/arch/arm/mach-omap2/mmc-twl4030.c index 1541fd4c8d0..3c04c2f1b23 100644 --- a/arch/arm/mach-omap2/mmc-twl4030.c +++ b/arch/arm/mach-omap2/mmc-twl4030.c @@ -119,6 +119,7 @@ static int twl_mmc_late_init(struct device *dev) if (i != 0) break; ret = PTR_ERR(reg); + hsmmc[i].vcc = NULL; goto err; } hsmmc[i].vcc = reg; @@ -165,8 +166,13 @@ done: static void twl_mmc_cleanup(struct device *dev) { struct omap_mmc_platform_data *mmc = dev->platform_data; + int i; gpio_free(mmc->slots[0].switch_pin); + for(i = 0; i < ARRAY_SIZE(hsmmc); i++) { + regulator_put(hsmmc[i].vcc); + regulator_put(hsmmc[i].vcc_aux); + } } #ifdef CONFIG_PM -- GitLab From 4177662ec9f5e50b69ef074369fdb429dd48d97e Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Mon, 10 Aug 2009 14:49:52 +0300 Subject: [PATCH 0995/1342] OMAP3: RX51: Updated rx51_defconfig Added REGULATOR, MMC and updated default CMDLINE so RX51 now boots. Note that the regulator code should be moved from mmc-twl4030.c to omap_hsmmc.c so it can be a module. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/configs/rx51_defconfig | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/arch/arm/configs/rx51_defconfig b/arch/arm/configs/rx51_defconfig index eb2cb31825c..f238df66efd 100644 --- a/arch/arm/configs/rx51_defconfig +++ b/arch/arm/configs/rx51_defconfig @@ -282,7 +282,7 @@ CONFIG_ALIGNMENT_TRAP=y # CONFIG_ZBOOT_ROM_TEXT=0x0 CONFIG_ZBOOT_ROM_BSS=0x0 -CONFIG_CMDLINE="init=/sbin/preinit ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs rootflags=bulk_read,no_chk_data_crc rw console=ttyMTD,log console=tty0" +CONFIG_CMDLINE="init=/sbin/preinit ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs rootflags=bulk_read,no_chk_data_crc rw console=ttyMTD,log console=tty0 console=ttyS2,115200n8" # CONFIG_XIP_KERNEL is not set # CONFIG_KEXEC is not set @@ -1354,7 +1354,7 @@ CONFIG_USB_OTG_UTILS=y # CONFIG_USB_GPIO_VBUS is not set # CONFIG_ISP1301_OMAP is not set CONFIG_TWL4030_USB=y -CONFIG_MMC=m +CONFIG_MMC=y # CONFIG_MMC_DEBUG is not set # CONFIG_MMC_UNSAFE_RESUME is not set @@ -1449,7 +1449,8 @@ CONFIG_RTC_DRV_TWL4030=m # on-CPU RTC drivers # # CONFIG_DMADEVICES is not set -# CONFIG_REGULATOR is not set +CONFIG_REGULATOR=y +CONFIG_REGULATOR_TWL4030=y # CONFIG_UIO is not set # CONFIG_STAGING is not set -- GitLab From 2fc391112fb6f3424435a3aa2fda887497b5f807 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Mon, 10 Aug 2009 12:33:05 +0100 Subject: [PATCH 0996/1342] locking, sched: Give waitqueue spinlocks their own lockdep classes Give waitqueue spinlocks their own lockdep classes when they are initialised from init_waitqueue_head(). This means that struct wait_queue::func functions can operate other waitqueues. This is used by CacheFiles to catch the page from a backing fs being unlocked and to wake up another thread to take a copy of it. Signed-off-by: Peter Zijlstra Signed-off-by: David Howells Tested-by: Takashi Iwai Cc: linux-cachefs@redhat.com Cc: torvalds@osdl.org Cc: akpm@linux-foundation.org LKML-Reference: <20090810113305.17284.81508.stgit@warthog.procyon.org.uk> Signed-off-by: Ingo Molnar --- include/linux/wait.h | 9 ++++++++- kernel/wait.c | 5 +++-- 2 files changed, 11 insertions(+), 3 deletions(-) diff --git a/include/linux/wait.h b/include/linux/wait.h index 6788e1a4d4c..cf3c2f5dba5 100644 --- a/include/linux/wait.h +++ b/include/linux/wait.h @@ -77,7 +77,14 @@ struct task_struct; #define __WAIT_BIT_KEY_INITIALIZER(word, bit) \ { .flags = word, .bit_nr = bit, } -extern void init_waitqueue_head(wait_queue_head_t *q); +extern void __init_waitqueue_head(wait_queue_head_t *q, struct lock_class_key *); + +#define init_waitqueue_head(q) \ + do { \ + static struct lock_class_key __key; \ + \ + __init_waitqueue_head((q), &__key); \ + } while (0) #ifdef CONFIG_LOCKDEP # define __WAIT_QUEUE_HEAD_INIT_ONSTACK(name) \ diff --git a/kernel/wait.c b/kernel/wait.c index ea7c3b4275c..c4bd3d825f3 100644 --- a/kernel/wait.c +++ b/kernel/wait.c @@ -10,13 +10,14 @@ #include #include -void init_waitqueue_head(wait_queue_head_t *q) +void __init_waitqueue_head(wait_queue_head_t *q, struct lock_class_key *key) { spin_lock_init(&q->lock); + lockdep_set_class(&q->lock, key); INIT_LIST_HEAD(&q->task_list); } -EXPORT_SYMBOL(init_waitqueue_head); +EXPORT_SYMBOL(__init_waitqueue_head); void add_wait_queue(wait_queue_head_t *q, wait_queue_t *wait) { -- GitLab From 4dc88029fd916b860ef063c40180aa604ce93494 Mon Sep 17 00:00:00 2001 From: Dinakar Guniguntala Date: Mon, 10 Aug 2009 18:31:42 +0530 Subject: [PATCH 0997/1342] futex: Fix compat_futex to be same as futex for REQUEUE_PI Need to add the REQUEUE_PI checks to the compat_sys_futex API as well to ensure 32 bit requeue's work fine on a 64 bit system. Patch is against latest tip Signed-off-by: Dinakar Guniguntala Cc: Darren Hart LKML-Reference: <20090810130142.GA23619@in.ibm.com> Signed-off-by: Ingo Molnar --- kernel/futex_compat.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/kernel/futex_compat.c b/kernel/futex_compat.c index d607a5b9ee2..235716556bf 100644 --- a/kernel/futex_compat.c +++ b/kernel/futex_compat.c @@ -180,7 +180,8 @@ asmlinkage long compat_sys_futex(u32 __user *uaddr, int op, u32 val, int cmd = op & FUTEX_CMD_MASK; if (utime && (cmd == FUTEX_WAIT || cmd == FUTEX_LOCK_PI || - cmd == FUTEX_WAIT_BITSET)) { + cmd == FUTEX_WAIT_BITSET || + cmd == FUTEX_WAIT_REQUEUE_PI)) { if (get_compat_timespec(&ts, utime)) return -EFAULT; if (!timespec_valid(&ts)) @@ -191,7 +192,8 @@ asmlinkage long compat_sys_futex(u32 __user *uaddr, int op, u32 val, t = ktime_add_safe(ktime_get(), t); tp = &t; } - if (cmd == FUTEX_REQUEUE || cmd == FUTEX_CMP_REQUEUE) + if (cmd == FUTEX_REQUEUE || cmd == FUTEX_CMP_REQUEUE || + cmd == FUTEX_CMP_REQUEUE_PI || cmd == FUTEX_WAKE_OP) val2 = (int) (unsigned long) utime; return do_futex(uaddr, op, val, tp, uaddr2, val2, val3); -- GitLab From 304703aba31a87903b8c0db8f5e6890cac2d596d Mon Sep 17 00:00:00 2001 From: Frederic Weisbecker Date: Mon, 10 Aug 2009 16:11:32 +0200 Subject: [PATCH 0998/1342] perf_counter: Subtract the buffer size field from the event record size We compute the perf raw sample size by aligning the raw ftrace event size plus the buffer size field itself. We do that instead of aligning only the perf raw sample size, so that we might economize some in some cases. But this buffer size field is not stored in the perf raw sample, we must then substract its size from the buffer once we computed the alignment unless we may get a useless u32 field in the buffer. Signed-off-by: Frederic Weisbecker Acked-by: Peter Zijlstra Cc: Arnaldo Carvalho de Melo Cc: Mike Galbraith Cc: Paul Mackerras LKML-Reference: <20090810141129.GA5124@nowhere> Signed-off-by: Ingo Molnar --- include/trace/ftrace.h | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/include/trace/ftrace.h b/include/trace/ftrace.h index 7167b9b97da..a05524fa245 100644 --- a/include/trace/ftrace.h +++ b/include/trace/ftrace.h @@ -637,7 +637,12 @@ __attribute__((section("_ftrace_events"))) event_##call = { \ * pc = preempt_count(); * * __data_size = ftrace_get_offsets_(&__data_offsets, args); - * __entry_size = __data_size + sizeof(*entry); + * + * // Below we want to get the aligned size by taking into account + * // the u32 field that will later store the buffer size + * __entry_size = ALIGN(__data_size + sizeof(*entry) + sizeof(u32), + * sizeof(u64)); + * __entry_size -= sizeof(u32); * * do { * char raw_data[__entry_size]; <- allocate our sample in the stack @@ -687,6 +692,7 @@ static void ftrace_profile_##call(proto) \ __data_size = ftrace_get_offsets_##call(&__data_offsets, args); \ __entry_size = ALIGN(__data_size + sizeof(*entry) + sizeof(u32),\ sizeof(u64)); \ + __entry_size -= sizeof(u32); \ \ do { \ char raw_data[__entry_size]; \ -- GitLab From 1853db0e02ae4088f102b0d8e59e83dc98f93f03 Mon Sep 17 00:00:00 2001 From: Frederic Weisbecker Date: Mon, 10 Aug 2009 16:38:36 +0200 Subject: [PATCH 0999/1342] perf_counter: Zero dead bytes from ftrace raw samples size alignment After aligning the ftrace raw samples, there are dead bytes storing random data from the stack. We don't want to leak these to userspace, then zero these out. Before: 0x2de88 [0x50]: event: 9 . . ... raw event: size 80 bytes . 0000: 09 00 00 00 01 00 50 00 d0 c7 00 81 ff ff ff ff ......P........ . 0010: 68 01 00 00 68 01 00 00 2c 00 00 00 00 00 00 00 h...h...,...... . 0020: 2c 00 00 00 2b 00 01 02 68 01 00 00 68 01 00 00 ,...+...h...h.. . 0030: 6b 6f 6e 64 65 6d 61 6e 64 2f 30 00 00 00 00 00 kondemand/0.... . 0040: 68 01 00 00 40 7f 46 81 ff ff ff ff 00 10 1b 7f h...@.F........ ^ ^ ^ ^ Leak After: 0x2d318 [0x50]: event: 9 . . ... raw event: size 80 bytes . 0000: 09 00 00 00 01 00 50 00 d0 c7 00 81 ff ff ff ff ......P........ . 0010: 68 01 00 00 68 01 00 00 68 14 00 00 00 00 00 00 h...h...h...... . 0020: 2c 00 00 00 2b 00 01 02 68 01 00 00 68 01 00 00 ,...+...h...h.. . 0030: 6b 6f 6e 64 65 6d 61 6e 64 2f 30 00 00 00 00 00 kondemand/0.... . 0040: 68 01 00 00 a0 80 46 81 ff ff ff ff 00 00 00 00 h.....F........ ^ ^ ^ ^ Fixed Reported-by: Peter Zijlstra Signed-off-by: Frederic Weisbecker Cc: Frederic Weisbecker Cc: Peter Zijlstra Cc: Arnaldo Carvalho de Melo Cc: Mike Galbraith LKML-Reference: <1249915116-5210-1-git-send-email-fweisbec@gmail.com> Signed-off-by: Ingo Molnar Cc: Peter Zijlstra Cc: Arnaldo Carvalho de Melo Cc: Mike Galbraith --- include/trace/ftrace.h | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/include/trace/ftrace.h b/include/trace/ftrace.h index a05524fa245..f64fbaae781 100644 --- a/include/trace/ftrace.h +++ b/include/trace/ftrace.h @@ -648,6 +648,9 @@ __attribute__((section("_ftrace_events"))) event_##call = { \ * char raw_data[__entry_size]; <- allocate our sample in the stack * struct trace_entry *ent; * + * zero dead bytes from alignment to avoid stack leak to userspace: + * + * *(u64 *)(&raw_data[__entry_size - sizeof(u64)]) = 0ULL; * entry = (struct ftrace_raw_ *)raw_data; * ent = &entry->ent; * tracing_generic_entry_update(ent, irq_flags, pc); @@ -698,6 +701,7 @@ static void ftrace_profile_##call(proto) \ char raw_data[__entry_size]; \ struct trace_entry *ent; \ \ + *(u64 *)(&raw_data[__entry_size - sizeof(u64)]) = 0ULL; \ entry = (struct ftrace_raw_##call *)raw_data; \ ent = &entry->ent; \ tracing_generic_entry_update(ent, irq_flags, pc); \ -- GitLab From 1392e3b33319fd1a2527bebfc56631c2f2d3c7c5 Mon Sep 17 00:00:00 2001 From: Ryusuke Konishi Date: Sat, 8 Aug 2009 17:52:50 +0900 Subject: [PATCH 1000/1342] documentation: register ioctl entry of nilfs2 This will register the ioctl range used by nilfs2 file system to the table listed in Documentation/ioctl/ioctl-number.txt. Signed-off-by: Ryusuke Konishi Signed-off-by: Linus Torvalds --- Documentation/ioctl/ioctl-number.txt | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/ioctl/ioctl-number.txt b/Documentation/ioctl/ioctl-number.txt index 7bb0d934b6d..dbea4f95fc8 100644 --- a/Documentation/ioctl/ioctl-number.txt +++ b/Documentation/ioctl/ioctl-number.txt @@ -139,6 +139,7 @@ Code Seq# Include File Comments 'm' all linux/synclink.h conflict! 'm' 00-1F net/irda/irmod.h conflict! 'n' 00-7F linux/ncp_fs.h +'n' 80-8F linux/nilfs2_fs.h NILFS2 'n' E0-FF video/matrox.h matroxfb 'o' 00-1F fs/ocfs2/ocfs2_fs.h OCFS2 'o' 00-03 include/mtd/ubi-user.h conflict! (OCFS2 and UBI overlaps) -- GitLab From 5e2f89b5d5d87a7c3ba19fc85ba0c29adb65f639 Mon Sep 17 00:00:00 2001 From: "Figo.zhang" Date: Sat, 8 Aug 2009 21:01:22 +0800 Subject: [PATCH 1001/1342] mempool.c: clean up type-casting clean up type-casting twice. "size_t" is typedef as "unsigned long" in 64-bit system, and "unsigned int" in 32-bit system, and the intermediate cast to 'long' is pointless. Signed-off-by: Figo.zhang Signed-off-by: Linus Torvalds --- mm/mempool.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/mm/mempool.c b/mm/mempool.c index a46eb1b4bb6..32e75d40050 100644 --- a/mm/mempool.c +++ b/mm/mempool.c @@ -303,14 +303,14 @@ EXPORT_SYMBOL(mempool_free_slab); */ void *mempool_kmalloc(gfp_t gfp_mask, void *pool_data) { - size_t size = (size_t)(long)pool_data; + size_t size = (size_t)pool_data; return kmalloc(size, gfp_mask); } EXPORT_SYMBOL(mempool_kmalloc); void *mempool_kzalloc(gfp_t gfp_mask, void *pool_data) { - size_t size = (size_t) pool_data; + size_t size = (size_t)pool_data; return kzalloc(size, gfp_mask); } EXPORT_SYMBOL(mempool_kzalloc); -- GitLab From 04e35357e2e3ff4e0cabd6468354cf3dbfeb4f27 Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Mon, 10 Aug 2009 16:45:42 +0100 Subject: [PATCH 1002/1342] MN10300: includecheck fix: mn10300, pci.h Fix the following 'make includecheck' warning: arch/mn10300/include/asm/pci.h: linux/mm.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Signed-off-by: David Howells Signed-off-by: Linus Torvalds --- arch/mn10300/include/asm/pci.h | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/mn10300/include/asm/pci.h b/arch/mn10300/include/asm/pci.h index 35d2ed6396f..19aecc90f7a 100644 --- a/arch/mn10300/include/asm/pci.h +++ b/arch/mn10300/include/asm/pci.h @@ -59,7 +59,6 @@ void pcibios_penalize_isa_irq(int irq); #include #include #include -#include #include struct pci_dev; -- GitLab From b6e61eef4f9f94714ac3ee4a5c96862d9bcd1836 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Fri, 31 Jul 2009 12:45:41 -0700 Subject: [PATCH 1003/1342] x86: Fix serialization in pit_expect_msb() Wei Chong Tan reported a fast-PIT-calibration corner-case: | pit_expect_msb() is vulnerable to SMI disturbance corner case | in some platforms which causes /proc/cpuinfo to show wrong | CPU MHz value when quick_pit_calibrate() jumps to success | section. I think that the real issue isn't even an SMI - but the fact that in the very last iteration of the loop, there's no serializing instruction _after_ the last 'rdtsc'. So even in the absense of SMI's, we do have a situation where the cycle counter was read without proper serialization. The last check should be done outside the outer loop, since _inside_ the outer loop, we'll be testing that the PIT has the right MSB value has the right value in the next iteration. So only the _last_ iteration is special, because that's the one that will not check the PIT MSB value any more, and because the final 'get_cycles()' isn't serialized. In other words: - I'd like to move the PIT MSB check to after the last iteration, rather than in every iteration - I think we should comment on the fact that it's also a serializing instruction and so 'fences in' the TSC read. Here's a suggested replacement. Signed-off-by: Linus Torvalds Reported-by: "Tan, Wei Chong" Tested-by: "Tan, Wei Chong" LKML-Reference: Signed-off-by: Ingo Molnar --- arch/x86/kernel/tsc.c | 29 ++++++++++++++++++++++------- 1 file changed, 22 insertions(+), 7 deletions(-) diff --git a/arch/x86/kernel/tsc.c b/arch/x86/kernel/tsc.c index 6e1a368d21d..71f4368b357 100644 --- a/arch/x86/kernel/tsc.c +++ b/arch/x86/kernel/tsc.c @@ -275,15 +275,20 @@ static unsigned long pit_calibrate_tsc(u32 latch, unsigned long ms, int loopmin) * use the TSC value at the transitions to calculate a pretty * good value for the TSC frequencty. */ +static inline int pit_verify_msb(unsigned char val) +{ + /* Ignore LSB */ + inb(0x42); + return inb(0x42) == val; +} + static inline int pit_expect_msb(unsigned char val, u64 *tscp, unsigned long *deltap) { int count; u64 tsc = 0; for (count = 0; count < 50000; count++) { - /* Ignore LSB */ - inb(0x42); - if (inb(0x42) != val) + if (!pit_verify_msb(val)) break; tsc = get_cycles(); } @@ -336,8 +341,7 @@ static unsigned long quick_pit_calibrate(void) * to do that is to just read back the 16-bit counter * once from the PIT. */ - inb(0x42); - inb(0x42); + pit_verify_msb(0); if (pit_expect_msb(0xff, &tsc, &d1)) { for (i = 1; i <= MAX_QUICK_PIT_ITERATIONS; i++) { @@ -348,8 +352,19 @@ static unsigned long quick_pit_calibrate(void) * Iterate until the error is less than 500 ppm */ delta -= tsc; - if (d1+d2 < delta >> 11) - goto success; + if (d1+d2 >= delta >> 11) + continue; + + /* + * Check the PIT one more time to verify that + * all TSC reads were stable wrt the PIT. + * + * This also guarantees serialization of the + * last cycle read ('d2') in pit_expect_msb. + */ + if (!pit_verify_msb(0xfe - i)) + break; + goto success; } } printk("Fast TSC calibration failed\n"); -- GitLab From 392741e0a4e17c82e3978b7fcbf04291294dc0a1 Mon Sep 17 00:00:00 2001 From: Darren Hart Date: Fri, 7 Aug 2009 15:20:48 -0700 Subject: [PATCH 1004/1342] futex: Fix handling of bad requeue syscall pairing If futex_requeue(requeue_pi=1) finds a futex_q that was created by a call other the futex_wait_requeue_pi(), the q.rt_waiter may be null. If so, this will result in an oops from the following call graph: futex_requeue() rt_mutex_start_proxy_lock() task_blocks_on_rt_mutex() waiter->task dereference OOPS We currently WARN_ON() if this is detected, clearly this is inadequate. If we detect a mispairing in futex_requeue(), bail out, seding -EINVAL to user-space. V2: Fix parenthesis warnings. Signed-off-by: Darren Hart Acked-by: Peter Zijlstra Cc: Steven Rostedt Cc: John Kacur Cc: Eric Dumazet Cc: Dinakar Guniguntala Cc: John Stultz LKML-Reference: <4A7CA8C0.7010809@us.ibm.com> Signed-off-by: Ingo Molnar --- kernel/futex.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-) diff --git a/kernel/futex.c b/kernel/futex.c index 8cc3ee1363a..e18cfbdc719 100644 --- a/kernel/futex.c +++ b/kernel/futex.c @@ -1256,8 +1256,15 @@ retry_private: if (!match_futex(&this->key, &key1)) continue; - WARN_ON(!requeue_pi && this->rt_waiter); - WARN_ON(requeue_pi && !this->rt_waiter); + /* + * FUTEX_WAIT_REQEUE_PI and FUTEX_CMP_REQUEUE_PI should always + * be paired with each other and no other futex ops. + */ + if ((requeue_pi && !this->rt_waiter) || + (!requeue_pi && this->rt_waiter)) { + ret = -EINVAL; + break; + } /* * Wake nr_wake waiters. For requeue_pi, if we acquired the -- GitLab From 3e03bbeac541856aaaf1ce1ab0250b6a490e4099 Mon Sep 17 00:00:00 2001 From: Shunichi Fuji Date: Tue, 11 Aug 2009 03:34:40 +0900 Subject: [PATCH 1005/1342] x86: Add reboot quirk for every 5 series MacBook/Pro MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Reboot does not work on my MacBook Pro 13 inch (MacBookPro5,5) too. It seems all unibody MacBook and MacBookPro require PCI reboot handling, i guess. Following model/machine ID list shows unibody MacBook/Pro have the 5 series of model number: http://www.everymac.com/systems/by_capability/macs-by-machine-model-machine-id.html Signed-off-by: Shunichi Fuji Cc: Ozan ÇaÄŸlayan LKML-Reference: <30046e3b0908101134p6487ddbftd8776e4ddef204be@mail.gmail.com> Signed-off-by: Ingo Molnar --- arch/x86/kernel/reboot.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/arch/x86/kernel/reboot.c b/arch/x86/kernel/reboot.c index 9eb89760370..a06e8d10184 100644 --- a/arch/x86/kernel/reboot.c +++ b/arch/x86/kernel/reboot.c @@ -418,20 +418,20 @@ static int __init set_pci_reboot(const struct dmi_system_id *d) } static struct dmi_system_id __initdata pci_reboot_dmi_table[] = { - { /* Handle problems with rebooting on Apple MacBook5,2 */ + { /* Handle problems with rebooting on Apple MacBook5 */ .callback = set_pci_reboot, - .ident = "Apple MacBook", + .ident = "Apple MacBook5", .matches = { DMI_MATCH(DMI_SYS_VENDOR, "Apple Inc."), - DMI_MATCH(DMI_PRODUCT_NAME, "MacBook5,2"), + DMI_MATCH(DMI_PRODUCT_NAME, "MacBook5"), }, }, - { /* Handle problems with rebooting on Apple MacBookPro5,1 */ + { /* Handle problems with rebooting on Apple MacBookPro5 */ .callback = set_pci_reboot, - .ident = "Apple MacBookPro5,1", + .ident = "Apple MacBookPro5", .matches = { DMI_MATCH(DMI_SYS_VENDOR, "Apple Inc."), - DMI_MATCH(DMI_PRODUCT_NAME, "MacBookPro5,1"), + DMI_MATCH(DMI_PRODUCT_NAME, "MacBookPro5"), }, }, { } -- GitLab From b409d7a0ab46fe530efe52734984b4ed5d46c3eb Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Thu, 6 Aug 2009 23:29:34 +0200 Subject: [PATCH 1006/1342] ocfs2: Fix possible deadlock when extending quota file In OCFS2, allocator locks rank above transaction start. Thus we cannot extend quota file from inside a transaction less we could deadlock. We solve the problem by starting transaction not already in ocfs2_acquire_dquot() but only in ocfs2_local_read_dquot() and ocfs2_global_read_dquot() and we allocate blocks to quota files before starting the transaction. In case we crash, quota files will just have a few blocks more but that's no problem since we just use them next time we extend the quota file. Signed-off-by: Jan Kara Signed-off-by: Joel Becker --- fs/ocfs2/journal.h | 5 -- fs/ocfs2/quota_global.c | 115 ++++++++++++++++++++-------------------- 2 files changed, 57 insertions(+), 63 deletions(-) diff --git a/fs/ocfs2/journal.h b/fs/ocfs2/journal.h index 4a4d3b55fd2..2c3222aec62 100644 --- a/fs/ocfs2/journal.h +++ b/fs/ocfs2/journal.h @@ -363,11 +363,6 @@ static inline int ocfs2_quota_trans_credits(struct super_block *sb) return credits; } -/* Number of credits needed for removing quota structure from file */ -int ocfs2_calc_qdel_credits(struct super_block *sb, int type); -/* Number of credits needed for initialization of new quota structure */ -int ocfs2_calc_qinit_credits(struct super_block *sb, int type); - /* group extend. inode update and last group update. */ #define OCFS2_GROUP_EXTEND_CREDITS (OCFS2_INODE_UPDATE_CREDITS + 1) diff --git a/fs/ocfs2/quota_global.c b/fs/ocfs2/quota_global.c index d604a6aa0a2..bf7742d0ee3 100644 --- a/fs/ocfs2/quota_global.c +++ b/fs/ocfs2/quota_global.c @@ -215,11 +215,7 @@ ssize_t ocfs2_quota_write(struct super_block *sb, int type, loff_t rounded_end = ocfs2_align_bytes_to_blocks(sb, off + len); - down_write(&OCFS2_I(gqinode)->ip_alloc_sem); - err = ocfs2_extend_no_holes(gqinode, rounded_end, off); - up_write(&OCFS2_I(gqinode)->ip_alloc_sem); - if (err < 0) - goto out; + /* Space is already allocated in ocfs2_global_read_dquot() */ err = ocfs2_simple_size_update(gqinode, oinfo->dqi_gqi_bh, rounded_end); @@ -405,13 +401,36 @@ int ocfs2_global_write_info(struct super_block *sb, int type) return err; } +static int ocfs2_global_qinit_alloc(struct super_block *sb, int type) +{ + struct ocfs2_mem_dqinfo *oinfo = sb_dqinfo(sb, type)->dqi_priv; + + /* + * We may need to allocate tree blocks and a leaf block but not the + * root block + */ + return oinfo->dqi_gi.dqi_qtree_depth; +} + +static int ocfs2_calc_global_qinit_credits(struct super_block *sb, int type) +{ + /* We modify all the allocated blocks, tree root, and info block */ + return (ocfs2_global_qinit_alloc(sb, type) + 2) * + OCFS2_QUOTA_BLOCK_UPDATE_CREDITS; +} + /* Read in information from global quota file and acquire a reference to it. * dquot_acquire() has already started the transaction and locked quota file */ int ocfs2_global_read_dquot(struct dquot *dquot) { int err, err2, ex = 0; - struct ocfs2_mem_dqinfo *info = - sb_dqinfo(dquot->dq_sb, dquot->dq_type)->dqi_priv; + struct super_block *sb = dquot->dq_sb; + int type = dquot->dq_type; + struct ocfs2_mem_dqinfo *info = sb_dqinfo(sb, type)->dqi_priv; + struct ocfs2_super *osb = OCFS2_SB(sb); + struct inode *gqinode = info->dqi_gqinode; + int need_alloc = ocfs2_global_qinit_alloc(sb, type); + handle_t *handle = NULL; err = ocfs2_qinfo_lock(info, 0); if (err < 0) @@ -422,14 +441,33 @@ int ocfs2_global_read_dquot(struct dquot *dquot) OCFS2_DQUOT(dquot)->dq_use_count++; OCFS2_DQUOT(dquot)->dq_origspace = dquot->dq_dqb.dqb_curspace; OCFS2_DQUOT(dquot)->dq_originodes = dquot->dq_dqb.dqb_curinodes; + ocfs2_qinfo_unlock(info, 0); + if (!dquot->dq_off) { /* No real quota entry? */ - /* Upgrade to exclusive lock for allocation */ - ocfs2_qinfo_unlock(info, 0); - err = ocfs2_qinfo_lock(info, 1); - if (err < 0) - goto out_qlock; ex = 1; + /* + * Add blocks to quota file before we start a transaction since + * locking allocators ranks above a transaction start + */ + WARN_ON(journal_current_handle()); + down_write(&OCFS2_I(gqinode)->ip_alloc_sem); + err = ocfs2_extend_no_holes(gqinode, + gqinode->i_size + (need_alloc << sb->s_blocksize_bits), + gqinode->i_size); + up_write(&OCFS2_I(gqinode)->ip_alloc_sem); + if (err < 0) + goto out; + } + + handle = ocfs2_start_trans(osb, + ocfs2_calc_global_qinit_credits(sb, type)); + if (IS_ERR(handle)) { + err = PTR_ERR(handle); + goto out; } + err = ocfs2_qinfo_lock(info, ex); + if (err < 0) + goto out_trans; err = qtree_write_dquot(&info->dqi_gi, dquot); if (ex && info_dirty(sb_dqinfo(dquot->dq_sb, dquot->dq_type))) { err2 = __ocfs2_global_write_info(dquot->dq_sb, dquot->dq_type); @@ -441,6 +479,9 @@ out_qlock: ocfs2_qinfo_unlock(info, 1); else ocfs2_qinfo_unlock(info, 0); +out_trans: + if (handle) + ocfs2_commit_trans(osb, handle); out: if (err < 0) mlog_errno(err); @@ -638,24 +679,17 @@ out: return status; } -int ocfs2_calc_qdel_credits(struct super_block *sb, int type) +static int ocfs2_calc_qdel_credits(struct super_block *sb, int type) { - struct ocfs2_mem_dqinfo *oinfo; - int features[MAXQUOTAS] = { OCFS2_FEATURE_RO_COMPAT_USRQUOTA, - OCFS2_FEATURE_RO_COMPAT_GRPQUOTA }; - - if (!OCFS2_HAS_RO_COMPAT_FEATURE(sb, features[type])) - return 0; - - oinfo = sb_dqinfo(sb, type)->dqi_priv; + struct ocfs2_mem_dqinfo *oinfo = sb_dqinfo(sb, type)->dqi_priv; /* * We modify tree, leaf block, global info, local chunk header, * global and local inode; OCFS2_QINFO_WRITE_CREDITS already * accounts for inode update */ - return oinfo->dqi_gi.dqi_qtree_depth + + return (oinfo->dqi_gi.dqi_qtree_depth + 2) * + OCFS2_QUOTA_BLOCK_UPDATE_CREDITS + OCFS2_QINFO_WRITE_CREDITS + - 2 * OCFS2_QUOTA_BLOCK_UPDATE_CREDITS + OCFS2_INODE_UPDATE_CREDITS; } @@ -688,36 +722,10 @@ out: return status; } -int ocfs2_calc_qinit_credits(struct super_block *sb, int type) -{ - struct ocfs2_mem_dqinfo *oinfo; - int features[MAXQUOTAS] = { OCFS2_FEATURE_RO_COMPAT_USRQUOTA, - OCFS2_FEATURE_RO_COMPAT_GRPQUOTA }; - struct ocfs2_dinode *lfe, *gfe; - - if (!OCFS2_HAS_RO_COMPAT_FEATURE(sb, features[type])) - return 0; - - oinfo = sb_dqinfo(sb, type)->dqi_priv; - gfe = (struct ocfs2_dinode *)oinfo->dqi_gqi_bh->b_data; - lfe = (struct ocfs2_dinode *)oinfo->dqi_lqi_bh->b_data; - /* We can extend local file + global file. In local file we - * can modify info, chunk header block and dquot block. In - * global file we can modify info, tree and leaf block */ - return ocfs2_calc_extend_credits(sb, &lfe->id2.i_list, 0) + - ocfs2_calc_extend_credits(sb, &gfe->id2.i_list, 0) + - OCFS2_LOCAL_QINFO_WRITE_CREDITS + - 2 * OCFS2_QUOTA_BLOCK_UPDATE_CREDITS + - oinfo->dqi_gi.dqi_qtree_depth + - 2 * OCFS2_QUOTA_BLOCK_UPDATE_CREDITS; -} - static int ocfs2_acquire_dquot(struct dquot *dquot) { - handle_t *handle; struct ocfs2_mem_dqinfo *oinfo = sb_dqinfo(dquot->dq_sb, dquot->dq_type)->dqi_priv; - struct ocfs2_super *osb = OCFS2_SB(dquot->dq_sb); int status = 0; mlog_entry("id=%u, type=%d", dquot->dq_id, dquot->dq_type); @@ -726,16 +734,7 @@ static int ocfs2_acquire_dquot(struct dquot *dquot) status = ocfs2_lock_global_qf(oinfo, 1); if (status < 0) goto out; - handle = ocfs2_start_trans(osb, - ocfs2_calc_qinit_credits(dquot->dq_sb, dquot->dq_type)); - if (IS_ERR(handle)) { - status = PTR_ERR(handle); - mlog_errno(status); - goto out_ilock; - } status = dquot_acquire(dquot); - ocfs2_commit_trans(osb, handle); -out_ilock: ocfs2_unlock_global_qf(oinfo, 1); out: mlog_exit(status); -- GitLab From 85dfd81dc57e8183a277ddd7a56aa65c96f3f487 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Mon, 10 Aug 2009 13:21:19 -0700 Subject: [PATCH 1007/1342] pty: fix data loss when stopped (^S/^Q) Commit d945cb9cc ("pty: Rework the pty layer to use the normal buffering logic") dropped the test for 'tty->stopped' in pty_write_room(), which then causes the n_tty line discipline thing to not throttle the data properly when the tty is stopped. So instead of pausing the write due to the tty being stopped, the ldisc layer would go ahead and push it down to the pty. The pty write() routine would then refuse to take the data (because it _did_ check 'stopped'), and the data wouldn't actually be written. This whole stopped test should eventually be moved into the tty ldisc layer rather than have low-level tty drivers care about these things, but right now the fix is to just re-instate the missing pty 'stopped' handling. Reported-and-tested-by: Artur Skawina Cc: Alan Cox Signed-off-by: Linus Torvalds --- drivers/char/pty.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/char/pty.c b/drivers/char/pty.c index 6e6942c45f5..d083c73d784 100644 --- a/drivers/char/pty.c +++ b/drivers/char/pty.c @@ -144,6 +144,8 @@ static int pty_write(struct tty_struct *tty, const unsigned char *buf, static int pty_write_room(struct tty_struct *tty) { + if (tty->stopped) + return 0; return pty_space(tty->link); } -- GitLab From 363ec5614f86110c6a6bdd72ac2147ebafd3ff5e Mon Sep 17 00:00:00 2001 From: Christian Lamparter Date: Sat, 8 Aug 2009 17:09:48 +0200 Subject: [PATCH 1008/1342] ar9170usb: fix spurious firmware related message When ar9170-2.fw was missing, the driver erroneously complained about missing the initialization values file ar9170-1.fw... Signed-off-by: Christian Lamparter Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ar9170/usb.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/drivers/net/wireless/ath/ar9170/usb.c b/drivers/net/wireless/ath/ar9170/usb.c index 754b1f8d8da..007eb85fc67 100644 --- a/drivers/net/wireless/ath/ar9170/usb.c +++ b/drivers/net/wireless/ath/ar9170/usb.c @@ -598,11 +598,15 @@ static int ar9170_usb_request_firmware(struct ar9170_usb *aru) err = request_firmware(&aru->init_values, "ar9170-1.fw", &aru->udev->dev); + if (err) { + dev_err(&aru->udev->dev, "file with init values not found.\n"); + return err; + } err = request_firmware(&aru->firmware, "ar9170-2.fw", &aru->udev->dev); if (err) { release_firmware(aru->init_values); - dev_err(&aru->udev->dev, "file with init values not found.\n"); + dev_err(&aru->udev->dev, "firmware file not found.\n"); return err; } -- GitLab From e9d126cdfa60b575f1b5b02024c4faee27dccf07 Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Sun, 9 Aug 2009 14:24:09 +0200 Subject: [PATCH 1009/1342] ar9170: fix read & write outside array bounds queue == __AR9170_NUM_TXQ would cause a bug on the next line. found by Smatch ( http://repo.or.cz/w/smatch.git ). Cc: stable@kernel.org Reported-by: Dan Carpenter Signed-off-by: Dan Carpenter Signed-off-by: Christian Lamparter Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ar9170/main.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/net/wireless/ath/ar9170/main.c b/drivers/net/wireless/ath/ar9170/main.c index 9d38cf60a0d..88c3d857386 100644 --- a/drivers/net/wireless/ath/ar9170/main.c +++ b/drivers/net/wireless/ath/ar9170/main.c @@ -1967,13 +1967,14 @@ static int ar9170_conf_tx(struct ieee80211_hw *hw, u16 queue, int ret; mutex_lock(&ar->mutex); - if ((param) && !(queue > __AR9170_NUM_TXQ)) { + if (queue < __AR9170_NUM_TXQ) { memcpy(&ar->edcf[ar9170_qos_hwmap[queue]], param, sizeof(*param)); ret = ar9170_set_qos(ar); - } else + } else { ret = -EINVAL; + } mutex_unlock(&ar->mutex); return ret; -- GitLab From 651b1f125c7e3806bbd635739d009433dc07372d Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Mon, 10 Aug 2009 23:41:18 +0200 Subject: [PATCH 1010/1342] PM / Driver Core: Kill dev_pm_ops platform warning for now Commit 783ea7d4eeefe895f2731fe73ac951e94418927b (Driver Core: Rework platform suspend/resume, print warning) added a warning message printed for platform drivers that use the legacy PM callbacks rather than struct dev_pm_ops. Unfortunately, this resulted in some confusion and made some people try to convert drivers by replacing the old callbacks with struct dev_pm_ops in automatic way, which generally is not a good idea. Remove the platform device runtime dev_pm_ops warning for now, because it's annoying to users and it's not really necessary right now. [rjw: Modified the changelog to be more informative.] Signed-off-by: Magnus Damm Acked-by: Greg Kroah-Hartman Signed-off-by: Rafael J. Wysocki --- drivers/base/platform.c | 3 --- 1 file changed, 3 deletions(-) diff --git a/drivers/base/platform.c b/drivers/base/platform.c index 81cb01bfc35..456594bd97b 100644 --- a/drivers/base/platform.c +++ b/drivers/base/platform.c @@ -483,9 +483,6 @@ int platform_driver_register(struct platform_driver *drv) drv->driver.remove = platform_drv_remove; if (drv->shutdown) drv->driver.shutdown = platform_drv_shutdown; - if (drv->suspend || drv->resume) - pr_warning("Platform driver '%s' needs updating - please use " - "dev_pm_ops\n", drv->driver.name); return driver_register(&drv->driver); } -- GitLab From 314dabb83a547ec4da819e8cbc78fac9cec605cd Mon Sep 17 00:00:00 2001 From: James Morris Date: Mon, 10 Aug 2009 22:00:13 +1000 Subject: [PATCH 1011/1342] SELinux: fix memory leakage in /security/selinux/hooks.c Fix memory leakage in /security/selinux/hooks.c The buffer always needs to be freed here; we either error out or allocate more memory. Reported-by: iceberg Signed-off-by: James Morris Acked-by: Stephen Smalley --- security/selinux/hooks.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/security/selinux/hooks.c b/security/selinux/hooks.c index 15c2a08a66f..1e8cfc4c2ed 100644 --- a/security/selinux/hooks.c +++ b/security/selinux/hooks.c @@ -1285,6 +1285,8 @@ static int inode_doinit_with_dentry(struct inode *inode, struct dentry *opt_dent rc = inode->i_op->getxattr(dentry, XATTR_NAME_SELINUX, context, len); if (rc == -ERANGE) { + kfree(context); + /* Need a larger buffer. Query for the right size. */ rc = inode->i_op->getxattr(dentry, XATTR_NAME_SELINUX, NULL, 0); @@ -1292,7 +1294,6 @@ static int inode_doinit_with_dentry(struct inode *inode, struct dentry *opt_dent dput(dentry); goto out_unlock; } - kfree(context); len = rc; context = kmalloc(len+1, GFP_NOFS); if (!context) { -- GitLab From dd704698f56c1451fc9c5daadcd6e3a089de2c40 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Tue, 11 Aug 2009 08:45:11 +0200 Subject: [PATCH 1012/1342] ALSA: hda - Don't override ADC definitions for ALC codecs ALC269 and ALC861-VD parsers override the ADC definitions unconditionally without checking the spec definition. This causes the problem when any inconsistent ADC is set up in the device quirk (like ALC272 with digital-mic). This patch avoids the overriding by adding the proper checks. Reference: Novell bnc#529467 https://bugzilla.novell.com/show_bug.cgi?id=529467 Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_realtek.c | 18 ++++++++++++------ 1 file changed, 12 insertions(+), 6 deletions(-) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 5cc927f4783..fea976793ae 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -15579,9 +15579,12 @@ static int patch_alc861vd(struct hda_codec *codec) spec->stream_digital_playback = &alc861vd_pcm_digital_playback; spec->stream_digital_capture = &alc861vd_pcm_digital_capture; - spec->adc_nids = alc861vd_adc_nids; - spec->num_adc_nids = ARRAY_SIZE(alc861vd_adc_nids); - spec->capsrc_nids = alc861vd_capsrc_nids; + if (!spec->adc_nids) { + spec->adc_nids = alc861vd_adc_nids; + spec->num_adc_nids = ARRAY_SIZE(alc861vd_adc_nids); + } + if (!spec->capsrc_nids) + spec->capsrc_nids = alc861vd_capsrc_nids; set_capture_mixer(spec); set_beep_amp(spec, 0x0b, 0x05, HDA_INPUT); @@ -17498,9 +17501,12 @@ static int patch_alc662(struct hda_codec *codec) spec->stream_digital_playback = &alc662_pcm_digital_playback; spec->stream_digital_capture = &alc662_pcm_digital_capture; - spec->adc_nids = alc662_adc_nids; - spec->num_adc_nids = ARRAY_SIZE(alc662_adc_nids); - spec->capsrc_nids = alc662_capsrc_nids; + if (!spec->adc_nids) { + spec->adc_nids = alc662_adc_nids; + spec->num_adc_nids = ARRAY_SIZE(alc662_adc_nids); + } + if (!spec->capsrc_nids) + spec->capsrc_nids = alc662_capsrc_nids; if (!spec->cap_mixer) set_capture_mixer(spec); -- GitLab From 0d01f31439c1e4d602bf9fdc924ab66f407f5e38 Mon Sep 17 00:00:00 2001 From: Dmitry Torokhov Date: Sun, 9 Aug 2009 21:44:49 -0700 Subject: [PATCH 1013/1342] x86, mce: therm_throt - change when we print messages My Latitude d630 seems to be handling thermal events in SMI by lowering the max frequency of the CPU till it cools down but still leaks the "everything is normal" events. This spams the console and with high priority printks. Adjust therm_throt driver to only print messages about the fact that temperatire returned back to normal when leaving the throttling state. Also lower the severity of "back to normal" message from KERN_CRIT to KERN_INFO. Signed-off-by: Dmitry Torokhov Acked-by: H. Peter Anvin LKML-Reference: <20090810051513.0558F526EC9@mailhub.coreip.homeip.net> Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/mcheck/therm_throt.c | 18 +++++++++++------- 1 file changed, 11 insertions(+), 7 deletions(-) diff --git a/arch/x86/kernel/cpu/mcheck/therm_throt.c b/arch/x86/kernel/cpu/mcheck/therm_throt.c index bff8dd191dd..8bc64cfbe93 100644 --- a/arch/x86/kernel/cpu/mcheck/therm_throt.c +++ b/arch/x86/kernel/cpu/mcheck/therm_throt.c @@ -36,6 +36,7 @@ static DEFINE_PER_CPU(__u64, next_check) = INITIAL_JIFFIES; static DEFINE_PER_CPU(unsigned long, thermal_throttle_count); +static DEFINE_PER_CPU(bool, thermal_throttle_active); static atomic_t therm_throt_en = ATOMIC_INIT(0); @@ -96,24 +97,27 @@ static int therm_throt_process(int curr) { unsigned int cpu = smp_processor_id(); __u64 tmp_jiffs = get_jiffies_64(); + bool was_throttled = __get_cpu_var(thermal_throttle_active); + bool is_throttled = __get_cpu_var(thermal_throttle_active) = curr; - if (curr) + if (is_throttled) __get_cpu_var(thermal_throttle_count)++; - if (time_before64(tmp_jiffs, __get_cpu_var(next_check))) + if (!(was_throttled ^ is_throttled) && + time_before64(tmp_jiffs, __get_cpu_var(next_check))) return 0; __get_cpu_var(next_check) = tmp_jiffs + CHECK_INTERVAL; /* if we just entered the thermal event */ - if (curr) { + if (is_throttled) { printk(KERN_CRIT "CPU%d: Temperature above threshold, " - "cpu clock throttled (total events = %lu)\n", cpu, - __get_cpu_var(thermal_throttle_count)); + "cpu clock throttled (total events = %lu)\n", + cpu, __get_cpu_var(thermal_throttle_count)); add_taint(TAINT_MACHINE_CHECK); - } else { - printk(KERN_CRIT "CPU%d: Temperature/speed normal\n", cpu); + } else if (was_throttled) { + printk(KERN_INFO "CPU%d: Temperature/speed normal\n", cpu); } return 1; -- GitLab From 3c581a7f94542341bf0da496a226b44ac63521a8 Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Tue, 11 Aug 2009 10:47:36 +0200 Subject: [PATCH 1014/1342] perf_counter, x86: Fix lapic printk message Instead of this garbled bootup on UP Pentium-M systems: [ 0.015048] Performance Counters: [ 0.016004] no Local APIC, try rebooting with lapicno PMU driver, software counters only. Print: [ 0.015050] Performance Counters: [ 0.016004] no APIC, boot with the "lapic" boot parameter to force-enable it. [ 0.017003] no PMU driver, software counters only. Cf: Frederic Weisbecker Cc: Peter Zijlstra Cc: Paul Mackerras Cc: Arnaldo Carvalho de Melo Cc: Frederic Weisbecker LKML-Reference: Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/perf_counter.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/cpu/perf_counter.c b/arch/x86/kernel/cpu/perf_counter.c index a7aa8f90095..40e233a24d9 100644 --- a/arch/x86/kernel/cpu/perf_counter.c +++ b/arch/x86/kernel/cpu/perf_counter.c @@ -1590,7 +1590,7 @@ static int p6_pmu_init(void) } if (!cpu_has_apic) { - pr_info("no Local APIC, try rebooting with lapic"); + pr_info("no APIC, boot with the \"lapic\" boot parameter to force-enable it.\n"); return -ENODEV; } -- GitLab From f64ccccb8afa43abdd63fcbd230f818d6ea0883f Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Tue, 11 Aug 2009 10:26:33 +0200 Subject: [PATCH 1015/1342] perf_counter, x86: Fix generic cache events on P6-mobile CPUs Johannes Stezenbach reported that 'perf stat' does not count cache-miss and cache-references events on his Pentium-M based laptop. This is because we left them blank in p6_perfmon_event_map[], fill them in. Reported-by: Johannes Stezenbach Cc: Peter Zijlstra Cc: Mike Galbraith Cc: Paul Mackerras Cc: Arnaldo Carvalho de Melo Cc: Frederic Weisbecker LKML-Reference: Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/perf_counter.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/x86/kernel/cpu/perf_counter.c b/arch/x86/kernel/cpu/perf_counter.c index 40e233a24d9..fffc126dbdf 100644 --- a/arch/x86/kernel/cpu/perf_counter.c +++ b/arch/x86/kernel/cpu/perf_counter.c @@ -72,8 +72,8 @@ static const u64 p6_perfmon_event_map[] = { [PERF_COUNT_HW_CPU_CYCLES] = 0x0079, [PERF_COUNT_HW_INSTRUCTIONS] = 0x00c0, - [PERF_COUNT_HW_CACHE_REFERENCES] = 0x0000, - [PERF_COUNT_HW_CACHE_MISSES] = 0x0000, + [PERF_COUNT_HW_CACHE_REFERENCES] = 0x0f2e, + [PERF_COUNT_HW_CACHE_MISSES] = 0x012e, [PERF_COUNT_HW_BRANCH_INSTRUCTIONS] = 0x00c4, [PERF_COUNT_HW_BRANCH_MISSES] = 0x00c5, [PERF_COUNT_HW_BUS_CYCLES] = 0x0062, -- GitLab From fbd8b1819e80ac5a176d085fdddc3a34d1499318 Mon Sep 17 00:00:00 2001 From: Kevin Winchester Date: Mon, 10 Aug 2009 19:56:45 -0300 Subject: [PATCH 1016/1342] x86: Clear incorrectly forced X86_FEATURE_LAHF_LM flag Due to an erratum with certain AMD Athlon 64 processors, the BIOS may need to force enable the LAHF_LM capability. Unfortunately, in at least one case, the BIOS does this even for processors that do not support the functionality. Add a specific check that will clear the feature bit for processors known not to support the LAHF/SAHF instructions. Signed-off-by: Kevin Winchester Acked-by: Borislav Petkov LKML-Reference: <4A80A5AD.2000209@gmail.com> Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/amd.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/x86/kernel/cpu/amd.c b/arch/x86/kernel/cpu/amd.c index e2485b03f1c..63fddcd082c 100644 --- a/arch/x86/kernel/cpu/amd.c +++ b/arch/x86/kernel/cpu/amd.c @@ -400,6 +400,13 @@ static void __cpuinit init_amd(struct cpuinfo_x86 *c) level = cpuid_eax(1); if((level >= 0x0f48 && level < 0x0f50) || level >= 0x0f58) set_cpu_cap(c, X86_FEATURE_REP_GOOD); + + /* + * Some BIOSes incorrectly force this feature, but only K8 + * revision D (model = 0x14) and later actually support it. + */ + if (c->x86_model < 0x14) + clear_cpu_cap(c, X86_FEATURE_LAHF_LM); } if (c->x86 == 0x10 || c->x86 == 0x11) set_cpu_cap(c, X86_FEATURE_REP_GOOD); -- GitLab From dee2b904a1f93c275a015b67cd693038d74b18e8 Mon Sep 17 00:00:00 2001 From: Mikael Pettersson Date: Sun, 9 Aug 2009 21:21:57 +0200 Subject: [PATCH 1017/1342] IXP4xx: Fix IO_SPACE_LIMIT for 2.6.31-rc core PCI changes MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit 2.6.31-rc kernels don't boot on my ixp4xx box (ds101), because the libata driver doesn't find the PCI IDE controller any more. 2.6.30 was fine. I traced this to a PCI update (1f82de10d6b1d845155363c895c552e61b36b51a) in 2.6.30-git19. Diffing the kernel boot logs from 2.6.30-git18 and 2.6.30-git19 illustrates the breakage: > --- dmesg-2.6.30-git18 2009-08-04 01:45:22.000000000 +0200 > +++ dmesg-2.6.30-git19 2009-08-04 01:45:46.000000000 +0200 > @@ -26,6 +26,13 @@ > pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot > pci 0000:00:02.2: PME# disabled > PCI: bus0: Fast back to back transfers disabled > +pci 0000:00:01.0: BAR 0: can't allocate I/O resource [0x10000-0xffff] > +pci 0000:00:01.0: BAR 1: can't allocate I/O resource [0x10000-0xffff] > +pci 0000:00:01.0: BAR 2: can't allocate I/O resource [0x10000-0xffff] > +pci 0000:00:01.0: BAR 3: can't allocate I/O resource [0x10000-0xffff] > +pci 0000:00:01.0: BAR 4: can't allocate I/O resource [0x10000-0xffff] > +pci 0000:00:02.0: BAR 4: can't allocate I/O resource [0x10000-0xffff] > +pci 0000:00:02.1: BAR 4: can't allocate I/O resource [0x10000-0xffff] > bio: create slab at 0 > SCSI subsystem initialized > NET: Registered protocol family 2 > @@ -44,11 +51,7 @@ > console [ttyS0] enabled > serial8250.0: ttyS1 at MMIO 0xc8001000 (irq = 13) is a XScale > Driver 'sd' needs updating - please use bus_type methods > -PCI: enabling device 0000:00:01.0 (0140 -> 0141) > -scsi0 : pata_artop > -scsi1 : pata_artop > -ata1: PATA max UDMA/100 cmd 0x1050 ctl 0x1060 bmdma 0x1040 irq 28 > -ata2: PATA max UDMA/100 cmd 0x1058 ctl 0x1064 bmdma 0x1048 irq 28 > +pata_artop 0000:00:01.0: no available native port > Using configured DiskOnChip probe address 0x50000000 > DiskOnChip found at 0x50000000 > NAND device: Manufacturer ID: 0x98, Chip ID: 0x73 (Toshiba NAND 16MiB 3,3V 8-bit) The specific change in 1f82de10d6b1d845155363c895c552e61b36b51a responsible for this failure turned out to be the following: > --- a/drivers/pci/probe.c > +++ b/drivers/pci/probe.c > @@ -193,7 +193,7 @@ int __pci_read_base(struct pci_dev *dev, enum pci_bar_type type, > res->flags |= pci_calc_resource_flags(l) | IORESOURCE_SIZEALIGN; > if (type == pci_bar_io) { > l &= PCI_BASE_ADDRESS_IO_MASK; > - mask = PCI_BASE_ADDRESS_IO_MASK & 0xffff; > + mask = PCI_BASE_ADDRESS_IO_MASK & IO_SPACE_LIMIT; > } else { > l &= PCI_BASE_ADDRESS_MEM_MASK; > mask = (u32)PCI_BASE_ADDRESS_MEM_MASK; Every arch except arm's ixp4xx defines IO_SPACE_LIMIT as an all-bits-one bitmask, typically -1UL but sometimes only a 16-bit 0x0000ffff. But ixp4xx defines it as 0xffff0000, which is now causing the PCI failures. Russell King noted that ixp4xx has 64KB PCI IO space, so IO_SPACE_LIMIT should be 0x0000ffff. This patch makes that change, which fixes the PCI failures on my ixp4xx box. Signed-off-by: Mikael Pettersson Signed-off-by: Krzysztof HaÅ‚asa --- arch/arm/mach-ixp4xx/include/mach/io.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-ixp4xx/include/mach/io.h b/arch/arm/mach-ixp4xx/include/mach/io.h index ce63048d45e..8a947d42a6f 100644 --- a/arch/arm/mach-ixp4xx/include/mach/io.h +++ b/arch/arm/mach-ixp4xx/include/mach/io.h @@ -17,7 +17,7 @@ #include -#define IO_SPACE_LIMIT 0xffff0000 +#define IO_SPACE_LIMIT 0x0000ffff extern int (*ixp4xx_pci_read)(u32 addr, u32 cmd, u32* data); extern int ixp4xx_pci_write(u32 addr, u32 cmd, u32 data); -- GitLab From 51b89f7a6615eca184aa0b85db5781d931e9c8d1 Mon Sep 17 00:00:00 2001 From: Fenghua Yu <[fenghua.yu@intel.com]> Date: Tue, 11 Aug 2009 14:52:10 -0700 Subject: [PATCH 1018/1342] Bug Fix arch/ia64/kernel/pci-dma.c: fix recursive dma_supported() call in iommu_dma_supported() In commit 160c1d8e40866edfeae7d68816b7005d70acf391, dma_ops->dma_supported = iommu_dma_supported; This dma_ops->dma_supported is first called in platform_dma_init() during kernel boot. Then dma_ops->dma_supported will be called recursively in iommu_dma_supported. Kernel can not boot because kernel can not get out of iommu_dma_supported until it runs out of stack memory. Signed-off-by: Fenghua Yu --- arch/ia64/kernel/pci-dma.c | 5 ----- 1 file changed, 5 deletions(-) diff --git a/arch/ia64/kernel/pci-dma.c b/arch/ia64/kernel/pci-dma.c index 05695962fe4..f6b1ff0aea7 100644 --- a/arch/ia64/kernel/pci-dma.c +++ b/arch/ia64/kernel/pci-dma.c @@ -69,11 +69,6 @@ iommu_dma_init(void) int iommu_dma_supported(struct device *dev, u64 mask) { - struct dma_map_ops *ops = platform_dma_get_ops(dev); - - if (ops->dma_supported) - return ops->dma_supported(dev, mask); - /* Copied from i386. Doesn't make much sense, because it will only work for pci_alloc_coherent. The caller just has to use GFP_DMA in this case. */ -- GitLab From 8d6f9af91959256244878cd801c1c969e66cd093 Mon Sep 17 00:00:00 2001 From: Johannes Weiner <[hannes@cmpxchg.org]> Date: Tue, 11 Aug 2009 14:52:10 -0700 Subject: [PATCH 1019/1342] ia64: boolean __test_and_clear_bit __test_and_clear_bit() returns a bitfield with the tested-for bit set. Make it consistent with the other bitops - of ia64 but also every other architecture - and return a boolean value. Signed-off-by: Johannes Weiner Acked-by: Fenghua Yu --- arch/ia64/include/asm/bitops.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/ia64/include/asm/bitops.h b/arch/ia64/include/asm/bitops.h index e2ca8003733..57a2787bc9f 100644 --- a/arch/ia64/include/asm/bitops.h +++ b/arch/ia64/include/asm/bitops.h @@ -286,7 +286,7 @@ __test_and_clear_bit(int nr, volatile void * addr) { __u32 *p = (__u32 *) addr + (nr >> 5); __u32 m = 1 << (nr & 31); - int oldbitset = *p & m; + int oldbitset = (*p & m) != 0; *p &= ~m; return oldbitset; -- GitLab From cfa5f809e399c699974ba6018eefa022bbc2e16e Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput <[jaswinder@kernel.org]> Date: Tue, 11 Aug 2009 14:52:10 -0700 Subject: [PATCH 1020/1342] IA64: includecheck fix: ia64, ia64_ksyms.c fix the following 'make includecheck' warning: arch/ia64/kernel/ia64_ksyms.c: asm/page.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Fenghua Yu --- arch/ia64/kernel/ia64_ksyms.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/arch/ia64/kernel/ia64_ksyms.c b/arch/ia64/kernel/ia64_ksyms.c index 2d311864e35..8ebccb589e1 100644 --- a/arch/ia64/kernel/ia64_ksyms.c +++ b/arch/ia64/kernel/ia64_ksyms.c @@ -21,6 +21,7 @@ EXPORT_SYMBOL(csum_ipv6_magic); #include EXPORT_SYMBOL(clear_page); +EXPORT_SYMBOL(copy_page); #ifdef CONFIG_VIRTUAL_MEM_MAP #include @@ -60,9 +61,6 @@ EXPORT_SYMBOL(__udivdi3); EXPORT_SYMBOL(__moddi3); EXPORT_SYMBOL(__umoddi3); -#include -EXPORT_SYMBOL(copy_page); - #if defined(CONFIG_MD_RAID456) || defined(CONFIG_MD_RAID456_MODULE) extern void xor_ia64_2(void); extern void xor_ia64_3(void); -- GitLab From b5a8879347bbe68bd24c8870503bf6a0362da26b Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput <[jaswinder@kernel.org]> Date: Tue, 11 Aug 2009 14:52:11 -0700 Subject: [PATCH 1021/1342] IA64: includecheck fix: ia64, pgtable.h fix the following 'make includecheck' warning: arch/ia64/include/asm/pgtable.h: asm/processor.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Fenghua Yu --- arch/ia64/include/asm/pgtable.h | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/ia64/include/asm/pgtable.h b/arch/ia64/include/asm/pgtable.h index 0a9cc73d35c..8840a690d1e 100644 --- a/arch/ia64/include/asm/pgtable.h +++ b/arch/ia64/include/asm/pgtable.h @@ -155,7 +155,6 @@ #include #include #include -#include /* * Next come the mappings that determine how mmap() protection bits -- GitLab From bf2a4c7270b9a22243a91ab5efcc47aaf997c66b Mon Sep 17 00:00:00 2001 From: Fenghua Yu <[fenghua.yu@intel.com]> Date: Tue, 11 Aug 2009 14:52:11 -0700 Subject: [PATCH 1022/1342] arch/ia64/Makefile: Remove -mtune=merced in IA64 kernel build Between GCC version 3.4.0 and 4.3.3 (including 3.4.0 and 4.3.3), -mtune=merced is implemented in GCC. Starting from 4.4.0, -mtune=merced is deprecated. Even implemented in versions between 3.4.0 and 4.3.3, the -mtune=merced feature has been broken in some of the versions. For example, GCC 4.1.2 reports interanl tuning function errors during kernel building with -mtune=merced. Or GCC Bugzilla 16130 reports another -mtune=merced issue on GCC 3.4.1. So I would remove the -mtune=merced from IA64 kernel build. Without this option, kernel on Merced will remain the same except losing an unstable and out-of-date performance tunning feature. Since GCC version 3.4.0, -mtune=mckinley has been implemented. The -mtune=mckinley option functions the same as mtune=itanium2. And mtune=itanium2 is the default option. So we don't need to add mtune=mckinley either since its been the default option in any GCC version which implements this option. Signed-off-by: Fenghua Yu --- arch/ia64/Makefile | 5 ----- 1 file changed, 5 deletions(-) diff --git a/arch/ia64/Makefile b/arch/ia64/Makefile index 58a7e46affd..e7cbaa02cd0 100644 --- a/arch/ia64/Makefile +++ b/arch/ia64/Makefile @@ -41,11 +41,6 @@ $(error Sorry, you need a newer version of the assember, one that is built from ftp://ftp.hpl.hp.com/pub/linux-ia64/gas-030124.tar.gz) endif -ifeq ($(call cc-version),0304) - cflags-$(CONFIG_ITANIUM) += -mtune=merced - cflags-$(CONFIG_MCKINLEY) += -mtune=mckinley -endif - KBUILD_CFLAGS += $(cflags-y) head-y := arch/ia64/kernel/head.o arch/ia64/kernel/init_task.o -- GitLab From 5359dffd4396f281c5b77de1acbee6fb1b333b23 Mon Sep 17 00:00:00 2001 From: Fenghua Yu Date: Tue, 11 Aug 2009 14:52:11 -0700 Subject: [PATCH 1023/1342] ia64/topology.c: exit cache_add_dev when kobject_init_and_add fails Make cache_add_dev exit sysfs when kobject_init_and_add returns an error. Signed-off-by: Xiaotian Feng Signed-off-by: Fenghua Yu --- arch/ia64/kernel/topology.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/arch/ia64/kernel/topology.c b/arch/ia64/kernel/topology.c index bc80dff1df7..8f060352e12 100644 --- a/arch/ia64/kernel/topology.c +++ b/arch/ia64/kernel/topology.c @@ -372,6 +372,10 @@ static int __cpuinit cache_add_dev(struct sys_device * sys_dev) retval = kobject_init_and_add(&all_cpu_cache_info[cpu].kobj, &cache_ktype_percpu_entry, &sys_dev->kobj, "%s", "cache"); + if (unlikely(retval < 0)) { + cpu_cache_sysfs_exit(cpu); + return retval; + } for (i = 0; i < all_cpu_cache_info[cpu].num_cache_leaves; i++) { this_object = LEAF_KOBJECT_PTR(cpu,i); @@ -385,7 +389,7 @@ static int __cpuinit cache_add_dev(struct sys_device * sys_dev) } kobject_put(&all_cpu_cache_info[cpu].kobj); cpu_cache_sysfs_exit(cpu); - break; + return retval; } kobject_uevent(&(this_object->kobj), KOBJ_ADD); } -- GitLab From e7369e01eb85550ed60dd1b0e120b69dfb03dc23 Mon Sep 17 00:00:00 2001 From: Roel Kluin <[roel.kluin@gmail.com]> Date: Tue, 11 Aug 2009 14:52:11 -0700 Subject: [PATCH 1024/1342] arch/ia64/kernel/iosapic: missing test after ioremap() Missing test after ioremap() Signed-off-by: Roel Kluin Acked-by: Fenghua Yu --- arch/ia64/kernel/iosapic.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/ia64/kernel/iosapic.c b/arch/ia64/kernel/iosapic.c index c48b03f2b61..dab4d393908 100644 --- a/arch/ia64/kernel/iosapic.c +++ b/arch/ia64/kernel/iosapic.c @@ -1072,6 +1072,10 @@ iosapic_init (unsigned long phys_addr, unsigned int gsi_base) } addr = ioremap(phys_addr, 0); + if (addr == NULL) { + spin_unlock_irqrestore(&iosapic_lock, flags); + return -ENOMEM; + } ver = iosapic_version(addr); if ((err = iosapic_check_gsi_range(gsi_base, ver))) { iounmap(addr); -- GitLab From 0cc6eee130b0c062feec8446d9cecdb17d2cfad3 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Sat, 18 Jul 2009 18:14:53 -0400 Subject: [PATCH 1025/1342] xfs: avoid memory allocation under m_peraglock in growfs code Allocate the memory for the larger m_perag array before taking the per-AG lock as the per-AG lock can be taken under the i_lock which can be taken from reclaim context. Reported by the new reclaim context tracing in lockdep. Signed-off-by: Christoph Hellwig Reviewed-by: Felix Blyakher Signed-off-by: Felix Blyakher --- fs/xfs/xfs_fsops.c | 20 ++++++++++++++------ 1 file changed, 14 insertions(+), 6 deletions(-) diff --git a/fs/xfs/xfs_fsops.c b/fs/xfs/xfs_fsops.c index cbd451bb484..2d0b3e1da9e 100644 --- a/fs/xfs/xfs_fsops.c +++ b/fs/xfs/xfs_fsops.c @@ -167,17 +167,25 @@ xfs_growfs_data_private( new = nb - mp->m_sb.sb_dblocks; oagcount = mp->m_sb.sb_agcount; if (nagcount > oagcount) { + void *new_perag, *old_perag; + xfs_filestream_flush(mp); + + new_perag = kmem_zalloc(sizeof(xfs_perag_t) * nagcount, + KM_MAYFAIL); + if (!new_perag) + return XFS_ERROR(ENOMEM); + down_write(&mp->m_peraglock); - mp->m_perag = kmem_realloc(mp->m_perag, - sizeof(xfs_perag_t) * nagcount, - sizeof(xfs_perag_t) * oagcount, - KM_SLEEP); - memset(&mp->m_perag[oagcount], 0, - (nagcount - oagcount) * sizeof(xfs_perag_t)); + memcpy(new_perag, mp->m_perag, sizeof(xfs_perag_t) * oagcount); + old_perag = mp->m_perag; + mp->m_perag = new_perag; + mp->m_flags |= XFS_MOUNT_32BITINODES; nagimax = xfs_initialize_perag(mp, nagcount); up_write(&mp->m_peraglock); + + kmem_free(old_perag); } tp = xfs_trans_alloc(mp, XFS_TRANS_GROWFS); tp->t_flags |= XFS_TRANS_RESERVE; -- GitLab From ca35dcd6cae7d4a780c484c53f45548c4719f82c Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Sat, 18 Jul 2009 18:14:54 -0400 Subject: [PATCH 1026/1342] xfs: switch to NOFS allocation under i_lock in xfs_getbmap xfs_getbmap allocates memory with i_lock held, but i_lock is taken in reclaim context so all allocations under it must avoid recursions into the filesystem. Reported by the new reclaim context tracing in lockdep. Signed-off-by: Christoph Hellwig Reviewed-by: Felix Blyakher Signed-off-by: Felix Blyakher --- fs/xfs/xfs_bmap.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/xfs/xfs_bmap.c b/fs/xfs/xfs_bmap.c index 7928b9983c1..8ee5b5a76a2 100644 --- a/fs/xfs/xfs_bmap.c +++ b/fs/xfs/xfs_bmap.c @@ -6009,7 +6009,7 @@ xfs_getbmap( */ error = ENOMEM; subnex = 16; - map = kmem_alloc(subnex * sizeof(*map), KM_MAYFAIL); + map = kmem_alloc(subnex * sizeof(*map), KM_MAYFAIL | KM_NOFS); if (!map) goto out_unlock_ilock; -- GitLab From f41d7fb9da05b604f8a69fb6cac2a0563c8ede4e Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Sat, 18 Jul 2009 18:14:55 -0400 Subject: [PATCH 1027/1342] xfs: switch to NOFS allocation under i_lock in xfs_da_state_alloc xfs_da_state_alloc is always called with i_lock held, but i_lock is taken in reclaim context so all allocations under it must avoid recursions into the filesystem. Reported by the new reclaim context tracing in lockdep. Signed-off-by: Christoph Hellwig Reviewed-by: Felix Blyakher Signed-off-by: Felix Blyakher --- fs/xfs/xfs_da_btree.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/xfs/xfs_da_btree.c b/fs/xfs/xfs_da_btree.c index 9ff6e57a507..bd0bb6dfcdf 100644 --- a/fs/xfs/xfs_da_btree.c +++ b/fs/xfs/xfs_da_btree.c @@ -2201,7 +2201,7 @@ kmem_zone_t *xfs_dabuf_zone; /* dabuf zone */ xfs_da_state_t * xfs_da_state_alloc(void) { - return kmem_zone_zalloc(xfs_da_state_zone, KM_SLEEP); + return kmem_zone_zalloc(xfs_da_state_zone, KM_NOFS); } /* -- GitLab From 73195ed7864ae4a1fb0bea2ed9df59d19b4fde90 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Sat, 18 Jul 2009 18:14:56 -0400 Subject: [PATCH 1028/1342] xfs: switch to NOFS allocation under i_lock in xfs_da_buf_make i_lock is taken in the reclaim context so all allocations under it must avoid recursions into the filesystem. Reported by the new reclaim context tracing in lockdep. Signed-off-by: Christoph Hellwig Reviewed-by: Felix Blyakher Signed-off-by: Felix Blyakher --- fs/xfs/xfs_da_btree.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/fs/xfs/xfs_da_btree.c b/fs/xfs/xfs_da_btree.c index bd0bb6dfcdf..2847bbc1c53 100644 --- a/fs/xfs/xfs_da_btree.c +++ b/fs/xfs/xfs_da_btree.c @@ -2261,9 +2261,9 @@ xfs_da_buf_make(int nbuf, xfs_buf_t **bps, inst_t *ra) int off; if (nbuf == 1) - dabuf = kmem_zone_alloc(xfs_dabuf_zone, KM_SLEEP); + dabuf = kmem_zone_alloc(xfs_dabuf_zone, KM_NOFS); else - dabuf = kmem_alloc(XFS_DA_BUF_SIZE(nbuf), KM_SLEEP); + dabuf = kmem_alloc(XFS_DA_BUF_SIZE(nbuf), KM_NOFS); dabuf->dirty = 0; #ifdef XFS_DABUF_DEBUG dabuf->ra = ra; -- GitLab From 3f52c2f0a07c23771909cc53f2e9451a7f1bf253 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Sat, 18 Jul 2009 18:14:57 -0400 Subject: [PATCH 1029/1342] xfs: switch to NOFS allocation under i_lock in xfs_dir_cilookup_result xfs_dir_cilookup_result is always called with i_lock held, but i_lock is taken in reclaim context so all allocations under it must avoid recursions into the filesystem. Reported by the new reclaim context tracing in lockdep. Signed-off-by: Christoph Hellwig Reviewed-by: Felix Blyakher Signed-off-by: Felix Blyakher --- fs/xfs/xfs_dir2.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/xfs/xfs_dir2.c b/fs/xfs/xfs_dir2.c index c657bec6d95..bb1d58eb398 100644 --- a/fs/xfs/xfs_dir2.c +++ b/fs/xfs/xfs_dir2.c @@ -256,7 +256,7 @@ xfs_dir_cilookup_result( !(args->op_flags & XFS_DA_OP_CILOOKUP)) return EEXIST; - args->value = kmem_alloc(len, KM_MAYFAIL); + args->value = kmem_alloc(len, KM_NOFS | KM_MAYFAIL); if (!args->value) return ENOMEM; -- GitLab From 36fae17a648e0aee5d9560514d08477ef48dc87f Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Sat, 18 Jul 2009 18:14:58 -0400 Subject: [PATCH 1030/1342] xfs: switch to NOFS allocation under i_lock in xfs_buf_associate_memory xfs_buf_associate_memory is used for setting up the spare buffer for the log wrap case in xlog_sync which can happen under i_lock when called from xfs_fsync. The i_lock mutex is taken in reclaim context so all allocations under it must avoid recursions into the filesystem. There are a couple more uses of xfs_buf_associate_memory in the log recovery code that are also affected by this, but I'd rather keep the code simple than passing on a gfp_mask argument. Longer term we should just stop requiring the memoery allocation in xlog_sync by some smaller rework of the buffer layer. Reported by the new reclaim context tracing in lockdep. Signed-off-by: Christoph Hellwig Reviewed-by: Felix Blyakher Signed-off-by: Felix Blyakher --- fs/xfs/linux-2.6/xfs_buf.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/xfs/linux-2.6/xfs_buf.c b/fs/xfs/linux-2.6/xfs_buf.c index 1418b916fc2..178c20c13e8 100644 --- a/fs/xfs/linux-2.6/xfs_buf.c +++ b/fs/xfs/linux-2.6/xfs_buf.c @@ -770,7 +770,7 @@ xfs_buf_associate_memory( bp->b_pages = NULL; bp->b_addr = mem; - rval = _xfs_buf_get_pages(bp, page_count, 0); + rval = _xfs_buf_get_pages(bp, page_count, XBF_DONT_BLOCK); if (rval) return rval; -- GitLab From 10746e47e722b5688fcd6eba9fbf9b2e64a248a7 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Sat, 18 Jul 2009 18:14:59 -0400 Subject: [PATCH 1031/1342] xfs: switch to NOFS allocation under i_lock in xfs_attr_rmtval_set xfs_attr_rmtval_set is always called with i_lock held, and i_lock is taken in reclaim context so all allocations under it must avoid recursions into the filesystem. Reported by the new reclaim context tracing in lockdep. Signed-off-by: Christoph Hellwig Reviewed-by: Felix Blyakher Signed-off-by: Felix Blyakher --- fs/xfs/xfs_attr.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/fs/xfs/xfs_attr.c b/fs/xfs/xfs_attr.c index db15feb906f..bfb583791fe 100644 --- a/fs/xfs/xfs_attr.c +++ b/fs/xfs/xfs_attr.c @@ -2141,8 +2141,8 @@ xfs_attr_rmtval_set(xfs_da_args_t *args) dblkno = XFS_FSB_TO_DADDR(mp, map.br_startblock), blkcnt = XFS_FSB_TO_BB(mp, map.br_blockcount); - bp = xfs_buf_get_flags(mp->m_ddev_targp, dblkno, - blkcnt, XFS_BUF_LOCK); + bp = xfs_buf_get_flags(mp->m_ddev_targp, dblkno, blkcnt, + XFS_BUF_LOCK | XBF_DONT_BLOCK); ASSERT(bp); ASSERT(!XFS_BUF_GETERROR(bp)); -- GitLab From 7b02ecb3031b192823bc732ae717febc0a59aa92 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Sat, 18 Jul 2009 18:15:00 -0400 Subject: [PATCH 1032/1342] xfs: switch to NOFS allocation under i_lock in xfs_readlink_bmap xfs_readlink_bmap is called with i_lock held, but i_lock is taken in reclaim context so all allocations under it must avoid recursions into the filesystem. Reported by the new reclaim context tracing in lockdep. Signed-off-by: Christoph Hellwig Reviewed-by: Felix Blyakher Signed-off-by: Felix Blyakher --- fs/xfs/xfs_vnodeops.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/fs/xfs/xfs_vnodeops.c b/fs/xfs/xfs_vnodeops.c index c4eca5ed5da..492d75bae2b 100644 --- a/fs/xfs/xfs_vnodeops.c +++ b/fs/xfs/xfs_vnodeops.c @@ -538,7 +538,9 @@ xfs_readlink_bmap( d = XFS_FSB_TO_DADDR(mp, mval[n].br_startblock); byte_cnt = XFS_FSB_TO_B(mp, mval[n].br_blockcount); - bp = xfs_buf_read(mp->m_ddev_targp, d, BTOBB(byte_cnt), 0); + bp = xfs_buf_read_flags(mp->m_ddev_targp, d, BTOBB(byte_cnt), + XBF_LOCK | XBF_MAPPED | + XBF_DONT_BLOCK); error = XFS_BUF_GETERROR(bp); if (error) { xfs_ioerror_alert("xfs_readlink", -- GitLab From ddd3a14e0f030f0f7b900621f67532285b8657ef Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Sat, 18 Jul 2009 18:15:01 -0400 Subject: [PATCH 1033/1342] xfs: switch to NOFS allocation under i_lock in xfs_attr_rmtval_get xfs_attr_rmtval_get is always called with i_lock held, but i_lock is taken in reclaim context so all allocations under it must avoid recursions into the filesystem. Reported by the new reclaim context tracing in lockdep. Signed-off-by: Christoph Hellwig Reviewed-by: Felix Blyakher Signed-off-by: Felix Blyakher --- fs/xfs/xfs_attr.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/fs/xfs/xfs_attr.c b/fs/xfs/xfs_attr.c index bfb583791fe..4ece1906bd4 100644 --- a/fs/xfs/xfs_attr.c +++ b/fs/xfs/xfs_attr.c @@ -2010,7 +2010,9 @@ xfs_attr_rmtval_get(xfs_da_args_t *args) dblkno = XFS_FSB_TO_DADDR(mp, map[i].br_startblock); blkcnt = XFS_FSB_TO_BB(mp, map[i].br_blockcount); error = xfs_read_buf(mp, mp->m_ddev_targp, dblkno, - blkcnt, XFS_BUF_LOCK, &bp); + blkcnt, + XFS_BUF_LOCK | XBF_DONT_BLOCK, + &bp); if (error) return(error); -- GitLab From e0c222c411e22f086e929cd69fdcc89336164ec1 Mon Sep 17 00:00:00 2001 From: Eric Sandeen Date: Mon, 20 Jul 2009 10:52:15 -0500 Subject: [PATCH 1034/1342] use XFS_CORRUPTION_ERROR in xfs_btree_check_sblock In Red Hat Bug 512552 - Can't write to XFS mount during raid5 resync a user ran into corruption while resyncing a raid, and we failed a consistency test, but didn't get much more info; it'd be nice to call XFS_CORRUPTION_ERROR here so we can see the buffer contents. Signed-off-by: Eric Sandeen Reviewed-by: Christoph Hellwig Signed-off-by: Felix Blyakher --- fs/xfs/xfs_btree.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/fs/xfs/xfs_btree.c b/fs/xfs/xfs_btree.c index e9df9957482..26717388acf 100644 --- a/fs/xfs/xfs_btree.c +++ b/fs/xfs/xfs_btree.c @@ -120,8 +120,8 @@ xfs_btree_check_sblock( XFS_RANDOM_BTREE_CHECK_SBLOCK))) { if (bp) xfs_buftrace("SBTREE ERROR", bp); - XFS_ERROR_REPORT("xfs_btree_check_sblock", XFS_ERRLEVEL_LOW, - cur->bc_mp); + XFS_CORRUPTION_ERROR("xfs_btree_check_sblock", + XFS_ERRLEVEL_LOW, cur->bc_mp, block); return XFS_ERROR(EFSCORRUPTED); } return 0; -- GitLab From b89d4208de3de442c9025919c4261be0b38e79a4 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Mon, 10 Aug 2009 11:32:18 -0300 Subject: [PATCH 1035/1342] xfs: check for dinode realtime flag corruption Ramon tested XFS with a modified version of fsfuzzer and hit a NULL pointer dereference in __xfs_get_blocks due to the RT device target pointer being NULL. To fix this reject inode with the realtime bit set on a a filesystem without an RT subvolume during inode read. Signed-off-by: Christoph Hellwig Reviewed-by: Eric Sandeen Reviewed-by: Felix Blyakher Reported-by: Ramon de Carvalho Valle Tested-by: Ramon de Carvalho Valle Signed-off-by: Felix Blyakher --- fs/xfs/xfs_inode.c | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/fs/xfs/xfs_inode.c b/fs/xfs/xfs_inode.c index 1f22d65fed0..da428b3fe0f 100644 --- a/fs/xfs/xfs_inode.c +++ b/fs/xfs/xfs_inode.c @@ -343,6 +343,16 @@ xfs_iformat( return XFS_ERROR(EFSCORRUPTED); } + if (unlikely((ip->i_d.di_flags & XFS_DIFLAG_REALTIME) && + !ip->i_mount->m_rtdev_targp)) { + xfs_fs_repair_cmn_err(CE_WARN, ip->i_mount, + "corrupt dinode %Lu, has realtime flag set.", + ip->i_ino); + XFS_CORRUPTION_ERROR("xfs_iformat(realtime)", + XFS_ERRLEVEL_LOW, ip->i_mount, dip); + return XFS_ERROR(EFSCORRUPTED); + } + switch (ip->i_d.di_mode & S_IFMT) { case S_IFIFO: case S_IFCHR: -- GitLab From a8914f3a6d72c97328597a556a99daaf5cc288ae Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Mon, 10 Aug 2009 11:32:44 -0300 Subject: [PATCH 1036/1342] xfs: fix spin_is_locked assert on uni-processor builds Without SMP or preemption spin_is_locked always returns false, so we can't do an assert with it. Instead use assert_spin_locked, which does the right thing on all builds. Signed-off-by: Christoph Hellwig Reviewed-by: Eric Sandeen Reported-by: Johannes Engel Tested-by: Johannes Engel Signed-off-by: Felix Blyakher --- fs/xfs/xfs_log.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/xfs/xfs_log.c b/fs/xfs/xfs_log.c index 3750f04ede0..9dbdff3ea48 100644 --- a/fs/xfs/xfs_log.c +++ b/fs/xfs/xfs_log.c @@ -3180,7 +3180,7 @@ try_again: STATIC void xlog_state_want_sync(xlog_t *log, xlog_in_core_t *iclog) { - ASSERT(spin_is_locked(&log->l_icloglock)); + assert_spin_locked(&log->l_icloglock); if (iclog->ic_state == XLOG_STATE_ACTIVE) { xlog_state_switch_iclogs(log, iclog, 0); -- GitLab From ec8b4b7085605e801a7740a2c3c33256aebe249c Mon Sep 17 00:00:00 2001 From: Stephen Kitt Date: Wed, 12 Aug 2009 01:12:08 -0700 Subject: [PATCH 1037/1342] Input: joydev - decouple axis and button map ioctls from input constants The KEY_MAX change in 2.6.28 changed the values of the JSIOCSBTNMAP and JSIOCGBTNMAP constants; software compiled with the old values no longer works with kernels following 2.6.28, because the ioctl switch statement no longer matches the values given by the software. This patch handles these ioctls independently of the length of data specified, and applies the same treatment to JSIOCSAXMAP and JSIOCGAXMAP which currently depend on ABS_MAX. Signed-off-by: Stephen Kitt Signed-off-by: Dmitry Torokhov --- drivers/input/joydev.c | 68 +++++++++++++++++++++++++----------------- 1 file changed, 41 insertions(+), 27 deletions(-) diff --git a/drivers/input/joydev.c b/drivers/input/joydev.c index 4cfd084fa89..9a1d55b74d7 100644 --- a/drivers/input/joydev.c +++ b/drivers/input/joydev.c @@ -456,8 +456,11 @@ static int joydev_ioctl_common(struct joydev *joydev, unsigned int cmd, void __user *argp) { struct input_dev *dev = joydev->handle.dev; + size_t len; int i, j; + const char *name; + /* Process fixed-sized commands. */ switch (cmd) { case JS_SET_CAL: @@ -499,9 +502,22 @@ static int joydev_ioctl_common(struct joydev *joydev, return copy_to_user(argp, joydev->corr, sizeof(joydev->corr[0]) * joydev->nabs) ? -EFAULT : 0; - case JSIOCSAXMAP: - if (copy_from_user(joydev->abspam, argp, - sizeof(__u8) * (ABS_MAX + 1))) + } + + /* + * Process variable-sized commands (the axis and button map commands + * are considered variable-sized to decouple them from the values of + * ABS_MAX and KEY_MAX). + */ + switch (cmd & ~IOCSIZE_MASK) { + + case (JSIOCSAXMAP & ~IOCSIZE_MASK): + len = min_t(size_t, _IOC_SIZE(cmd), sizeof(joydev->abspam)); + /* + * FIXME: we should not copy into our axis map before + * validating the data. + */ + if (copy_from_user(joydev->abspam, argp, len)) return -EFAULT; for (i = 0; i < joydev->nabs; i++) { @@ -511,13 +527,17 @@ static int joydev_ioctl_common(struct joydev *joydev, } return 0; - case JSIOCGAXMAP: - return copy_to_user(argp, joydev->abspam, - sizeof(__u8) * (ABS_MAX + 1)) ? -EFAULT : 0; - - case JSIOCSBTNMAP: - if (copy_from_user(joydev->keypam, argp, - sizeof(__u16) * (KEY_MAX - BTN_MISC + 1))) + case (JSIOCGAXMAP & ~IOCSIZE_MASK): + len = min_t(size_t, _IOC_SIZE(cmd), sizeof(joydev->abspam)); + return copy_to_user(argp, joydev->abspam, len) ? -EFAULT : 0; + + case (JSIOCSBTNMAP & ~IOCSIZE_MASK): + len = min_t(size_t, _IOC_SIZE(cmd), sizeof(joydev->keypam)); + /* + * FIXME: we should not copy into our keymap before + * validating the data. + */ + if (copy_from_user(joydev->keypam, argp, len)) return -EFAULT; for (i = 0; i < joydev->nkey; i++) { @@ -529,25 +549,19 @@ static int joydev_ioctl_common(struct joydev *joydev, return 0; - case JSIOCGBTNMAP: - return copy_to_user(argp, joydev->keypam, - sizeof(__u16) * (KEY_MAX - BTN_MISC + 1)) ? -EFAULT : 0; + case (JSIOCGBTNMAP & ~IOCSIZE_MASK): + len = min_t(size_t, _IOC_SIZE(cmd), sizeof(joydev->keypam)); + return copy_to_user(argp, joydev->keypam, len) ? -EFAULT : 0; - default: - if ((cmd & ~IOCSIZE_MASK) == JSIOCGNAME(0)) { - int len; - const char *name = dev->name; - - if (!name) - return 0; - len = strlen(name) + 1; - if (len > _IOC_SIZE(cmd)) - len = _IOC_SIZE(cmd); - if (copy_to_user(argp, name, len)) - return -EFAULT; - return len; - } + case JSIOCGNAME(0): + name = dev->name; + if (!name) + return 0; + + len = min_t(size_t, _IOC_SIZE(cmd), strlen(name) + 1); + return copy_to_user(argp, name, len) ? -EFAULT : len; } + return -EINVAL; } -- GitLab From e8055139d996e85722984968472868d6dccb1490 Mon Sep 17 00:00:00 2001 From: Ondrej Zary Date: Tue, 11 Aug 2009 20:00:11 +0200 Subject: [PATCH 1038/1342] x86: Fix oops in identify_cpu() on CPUs without CPUID Kernel is broken for x86 CPUs without CPUID since 2.6.28. It crashes with NULL pointer dereference in identify_cpu(): 766 generic_identify(c); 767 768--> if (this_cpu->c_identify) 769 this_cpu->c_identify(c); this_cpu is NULL. This is because it's only initialized in get_cpu_vendor() function, which is not called if the CPU has no CPUID instruction. Signed-off-by: Ondrej Zary LKML-Reference: <200908112000.15993.linux@rainbow-software.org> Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/common.c | 48 ++++++++++++++++++------------------ 1 file changed, 24 insertions(+), 24 deletions(-) diff --git a/arch/x86/kernel/cpu/common.c b/arch/x86/kernel/cpu/common.c index f1961c07af9..5ce60a88027 100644 --- a/arch/x86/kernel/cpu/common.c +++ b/arch/x86/kernel/cpu/common.c @@ -59,7 +59,30 @@ void __init setup_cpu_local_masks(void) alloc_bootmem_cpumask_var(&cpu_sibling_setup_mask); } -static const struct cpu_dev *this_cpu __cpuinitdata; +static void __cpuinit default_init(struct cpuinfo_x86 *c) +{ +#ifdef CONFIG_X86_64 + display_cacheinfo(c); +#else + /* Not much we can do here... */ + /* Check if at least it has cpuid */ + if (c->cpuid_level == -1) { + /* No cpuid. It must be an ancient CPU */ + if (c->x86 == 4) + strcpy(c->x86_model_id, "486"); + else if (c->x86 == 3) + strcpy(c->x86_model_id, "386"); + } +#endif +} + +static const struct cpu_dev __cpuinitconst default_cpu = { + .c_init = default_init, + .c_vendor = "Unknown", + .c_x86_vendor = X86_VENDOR_UNKNOWN, +}; + +static const struct cpu_dev *this_cpu __cpuinitdata = &default_cpu; DEFINE_PER_CPU_PAGE_ALIGNED(struct gdt_page, gdt_page) = { .gdt = { #ifdef CONFIG_X86_64 @@ -332,29 +355,6 @@ void switch_to_new_gdt(int cpu) static const struct cpu_dev *__cpuinitdata cpu_devs[X86_VENDOR_NUM] = {}; -static void __cpuinit default_init(struct cpuinfo_x86 *c) -{ -#ifdef CONFIG_X86_64 - display_cacheinfo(c); -#else - /* Not much we can do here... */ - /* Check if at least it has cpuid */ - if (c->cpuid_level == -1) { - /* No cpuid. It must be an ancient CPU */ - if (c->x86 == 4) - strcpy(c->x86_model_id, "486"); - else if (c->x86 == 3) - strcpy(c->x86_model_id, "386"); - } -#endif -} - -static const struct cpu_dev __cpuinitconst default_cpu = { - .c_init = default_init, - .c_vendor = "Unknown", - .c_x86_vendor = X86_VENDOR_UNKNOWN, -}; - static void __cpuinit get_model_name(struct cpuinfo_x86 *c) { unsigned int *v; -- GitLab From df9eba8c9febf53782ef896518e7177999d98188 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Fri, 7 Aug 2009 11:15:20 +0900 Subject: [PATCH 1039/1342] pata_at91: fix resource release Julias Lawall discovered that pata_at91 wasn't freeing a memory region allocated with kzalloc() on init failure paths. Upon review, pata_at91 also seems to be doing unnecessary explicit resource releases for managed resources too. Convert memory allocation to managed one and drop unnecessary explicit resource releases. Signed-off-by: Tejun Heo Cc: Julia Lawall Cc: Sergey Matyukevich Signed-off-by: Jeff Garzik --- drivers/ata/pata_at91.c | 17 ++++------------- 1 file changed, 4 insertions(+), 13 deletions(-) diff --git a/drivers/ata/pata_at91.c b/drivers/ata/pata_at91.c index 5702affcb32..41c94b1ae49 100644 --- a/drivers/ata/pata_at91.c +++ b/drivers/ata/pata_at91.c @@ -250,7 +250,7 @@ static int __devinit pata_at91_probe(struct platform_device *pdev) ata_port_desc(ap, "no IRQ, using PIO polling"); } - info = kzalloc(sizeof(*info), GFP_KERNEL); + info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL); if (!info) { dev_err(dev, "failed to allocate memory for private data\n"); @@ -275,7 +275,7 @@ static int __devinit pata_at91_probe(struct platform_device *pdev) if (!info->ide_addr) { dev_err(dev, "failed to map IO base\n"); ret = -ENOMEM; - goto err_ide_ioremap; + goto err_put; } info->alt_addr = devm_ioremap(dev, @@ -284,7 +284,7 @@ static int __devinit pata_at91_probe(struct platform_device *pdev) if (!info->alt_addr) { dev_err(dev, "failed to map CTL base\n"); ret = -ENOMEM; - goto err_alt_ioremap; + goto err_put; } ap->ioaddr.cmd_addr = info->ide_addr; @@ -303,13 +303,8 @@ static int __devinit pata_at91_probe(struct platform_device *pdev) irq ? ata_sff_interrupt : NULL, irq_flags, &pata_at91_sht); -err_alt_ioremap: - devm_iounmap(dev, info->ide_addr); - -err_ide_ioremap: +err_put: clk_put(info->mck); - kfree(info); - return ret; } @@ -317,7 +312,6 @@ static int __devexit pata_at91_remove(struct platform_device *pdev) { struct ata_host *host = dev_get_drvdata(&pdev->dev); struct at91_ide_info *info; - struct device *dev = &pdev->dev; if (!host) return 0; @@ -328,11 +322,8 @@ static int __devexit pata_at91_remove(struct platform_device *pdev) if (!info) return 0; - devm_iounmap(dev, info->ide_addr); - devm_iounmap(dev, info->alt_addr); clk_put(info->mck); - kfree(info); return 0; } -- GitLab From 1fd4bbec8c0d6db96b02141f324066afa2e77e89 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Thu, 6 Aug 2009 17:47:05 +0200 Subject: [PATCH 1040/1342] pata_atiixp: fix second channel support PIO and MWDMA timings are never programmed for the second channel because timing registers are treated as 16-bit long ones. The bug is an attixp -> pata_atiixp regression and goes back to: commit 669a5db411d85a14f86cd92bc16bf7ab5b8aa235 Author: Jeff Garzik Date: Tue Aug 29 18:12:40 2006 -0400 [libata] Add a bunch of PATA drivers. Cc: Krystian Juskowiak Cc: Andrew Morton Cc: Borislav Petkov Cc: Robert Hancock Signed-off-by: Bartlomiej Zolnierkiewicz Signed-off-by: Jeff Garzik --- drivers/ata/pata_atiixp.c | 19 ++++++++++--------- 1 file changed, 10 insertions(+), 9 deletions(-) diff --git a/drivers/ata/pata_atiixp.c b/drivers/ata/pata_atiixp.c index bec0b8ade66..45915566e4e 100644 --- a/drivers/ata/pata_atiixp.c +++ b/drivers/ata/pata_atiixp.c @@ -1,6 +1,7 @@ /* * pata_atiixp.c - ATI PATA for new ATA layer * (C) 2005 Red Hat Inc + * (C) 2009 Bartlomiej Zolnierkiewicz * * Based on * @@ -61,20 +62,19 @@ static void atiixp_set_pio_timing(struct ata_port *ap, struct ata_device *adev, struct pci_dev *pdev = to_pci_dev(ap->host->dev); int dn = 2 * ap->port_no + adev->devno; - - /* Check this is correct - the order is odd in both drivers */ int timing_shift = (16 * ap->port_no) + 8 * (adev->devno ^ 1); - u16 pio_mode_data, pio_timing_data; + u32 pio_timing_data; + u16 pio_mode_data; pci_read_config_word(pdev, ATIIXP_IDE_PIO_MODE, &pio_mode_data); pio_mode_data &= ~(0x7 << (4 * dn)); pio_mode_data |= pio << (4 * dn); pci_write_config_word(pdev, ATIIXP_IDE_PIO_MODE, pio_mode_data); - pci_read_config_word(pdev, ATIIXP_IDE_PIO_TIMING, &pio_timing_data); + pci_read_config_dword(pdev, ATIIXP_IDE_PIO_TIMING, &pio_timing_data); pio_timing_data &= ~(0xFF << timing_shift); pio_timing_data |= (pio_timings[pio] << timing_shift); - pci_write_config_word(pdev, ATIIXP_IDE_PIO_TIMING, pio_timing_data); + pci_write_config_dword(pdev, ATIIXP_IDE_PIO_TIMING, pio_timing_data); } /** @@ -119,16 +119,17 @@ static void atiixp_set_dmamode(struct ata_port *ap, struct ata_device *adev) udma_mode_data |= dma << (4 * dn); pci_write_config_word(pdev, ATIIXP_IDE_UDMA_MODE, udma_mode_data); } else { - u16 mwdma_timing_data; - /* Check this is correct - the order is odd in both drivers */ int timing_shift = (16 * ap->port_no) + 8 * (adev->devno ^ 1); + u32 mwdma_timing_data; dma -= XFER_MW_DMA_0; - pci_read_config_word(pdev, ATIIXP_IDE_MWDMA_TIMING, &mwdma_timing_data); + pci_read_config_dword(pdev, ATIIXP_IDE_MWDMA_TIMING, + &mwdma_timing_data); mwdma_timing_data &= ~(0xFF << timing_shift); mwdma_timing_data |= (mwdma_timings[dma] << timing_shift); - pci_write_config_word(pdev, ATIIXP_IDE_MWDMA_TIMING, mwdma_timing_data); + pci_write_config_dword(pdev, ATIIXP_IDE_MWDMA_TIMING, + mwdma_timing_data); } /* * We must now look at the PIO mode situation. We may need to -- GitLab From 7831387bda72af3059be48d39846d3eb6d8ce2f6 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Fri, 7 Aug 2009 01:59:15 +0900 Subject: [PATCH 1041/1342] libata: OCZ Vertex can't do HPA OCZ Vertex SSD can't do HPA and not in a usual way. It reports HPA, allows unlocking but then fails all IOs which fall in the unlocked area. Quirk it so that HPA unlocking is not used for the device. Reported by Daniel Perup in bnc#522414. https://bugzilla.novell.com/show_bug.cgi?id=522414 Signed-off-by: Tejun Heo Reported-by: Daniel Perup Signed-off-by: Jeff Garzik --- drivers/ata/libata-core.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index 8ac98ff16d7..072ba5ea138 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -4302,6 +4302,9 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = { { "WDC WD2500JD-00HBB0", "WD-WMAL71490727", ATA_HORKAGE_BROKEN_HPA }, { "MAXTOR 6L080L4", "A93.0500", ATA_HORKAGE_BROKEN_HPA }, + /* this one allows HPA unlocking but fails IOs on the area */ + { "OCZ-VERTEX", "1.30", ATA_HORKAGE_BROKEN_HPA }, + /* Devices which report 1 sector over size HPA */ { "ST340823A", NULL, ATA_HORKAGE_HPA_SIZE, }, { "ST320413A", NULL, ATA_HORKAGE_HPA_SIZE, }, -- GitLab From 51c8949950647afeeb897e08dd75ad99078adb50 Mon Sep 17 00:00:00 2001 From: Tony Vroon Date: Thu, 6 Aug 2009 00:50:09 +0100 Subject: [PATCH 1042/1342] sata_nv: MSI support, disabled by default At least the nVidia MCP55 controller quite happily supports MSI. This adds an option to use it. It is disabled by default. As per feedback by Robert Hancock, it will honour the user request as the kernel will not enable MSI where the controller or the specific system configuration do not support it. Signed-off-by: Tony Vroon Cc: Robert Hancock Signed-off-by: Jeff Garzik --- drivers/ata/sata_nv.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c index b2d11f300c3..86a40582999 100644 --- a/drivers/ata/sata_nv.c +++ b/drivers/ata/sata_nv.c @@ -602,6 +602,7 @@ MODULE_VERSION(DRV_VERSION); static int adma_enabled; static int swncq_enabled = 1; +static int msi_enabled; static void nv_adma_register_mode(struct ata_port *ap) { @@ -2459,6 +2460,11 @@ static int nv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) } else if (type == SWNCQ) nv_swncq_host_init(host); + if (msi_enabled) { + dev_printk(KERN_NOTICE, &pdev->dev, "Using MSI\n"); + pci_enable_msi(pdev); + } + pci_set_master(pdev); return ata_host_activate(host, pdev->irq, ipriv->irq_handler, IRQF_SHARED, ipriv->sht); @@ -2558,4 +2564,6 @@ module_param_named(adma, adma_enabled, bool, 0444); MODULE_PARM_DESC(adma, "Enable use of ADMA (Default: false)"); module_param_named(swncq, swncq_enabled, bool, 0444); MODULE_PARM_DESC(swncq, "Enable use of SWNCQ (Default: true)"); +module_param_named(msi, msi_enabled, bool, 0444); +MODULE_PARM_DESC(msi, "Enable use of MSI (Default: false)"); -- GitLab From 20308871588518b5e209c403de2a3ad9a2eba9af Mon Sep 17 00:00:00 2001 From: Michael Prokop Date: Thu, 6 Aug 2009 00:14:10 +0200 Subject: [PATCH 1043/1342] Documentation/kernel-parameters.txt: document libata's ignore_hpa option By default the kernel honors the HPA (host protected area) of hard drives. Using libata's ignore_hpa module option it's possible to change this behaviour. Document usage and options of libata.ignore_hpa in Documentation/kernel-parameters.txt. Signed-off-by: Michael Prokop Signed-off-by: Jeff Garzik --- Documentation/kernel-parameters.txt | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index dd1a6d4bb74..7936b801fe6 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -1115,6 +1115,10 @@ and is between 256 and 4096 characters. It is defined in the file libata.dma=4 Compact Flash DMA only Combinations also work, so libata.dma=3 enables DMA for disks and CDROMs, but not CFs. + + libata.ignore_hpa= [LIBATA] Ignore HPA limit + libata.ignore_hpa=0 keep BIOS limits (default) + libata.ignore_hpa=1 ignore limits, using full disk libata.noacpi [LIBATA] Disables use of ACPI in libata suspend/resume when set. -- GitLab From b6931c1fbaf7fda9ea7f120228a96600d7090049 Mon Sep 17 00:00:00 2001 From: Shane Huang Date: Wed, 5 Aug 2009 10:10:41 +0800 Subject: [PATCH 1044/1342] ahci: Soften up the dmesg on SB600 PMP softreset failure recovery Too strong words led to spurious bug reports: Novell bugzilla #527748, RedHat bugzilla #468800. This patch is used to soften up the dmesg on SB600 PMP softreset failure recovery, so as to remove the scariness and concern from community. Reported-by: pgnet Dev Signed-off-by: Shane Huang Cc: Tejun Heo Signed-off-by: Jeff Garzik --- drivers/ata/ahci.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c index 958c1fa4190..838ff73b08e 100644 --- a/drivers/ata/ahci.c +++ b/drivers/ata/ahci.c @@ -1773,7 +1773,8 @@ static int ahci_sb600_softreset(struct ata_link *link, unsigned int *class, irq_sts = readl(port_mmio + PORT_IRQ_STAT); if (irq_sts & PORT_IRQ_BAD_PMP) { ata_link_printk(link, KERN_WARNING, - "failed due to HW bug, retry pmp=0\n"); + "applying SB600 PMP SRST workaround " + "and retrying\n"); rc = ahci_do_softreset(link, class, 0, deadline, ahci_check_ready); } -- GitLab From 5594639aab8b5614cb27a3e5b2b627505cbcd137 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Tue, 4 Aug 2009 14:30:08 +0900 Subject: [PATCH 1045/1342] ahci: add workaround for on-board 5723s on some gigabyte boards Some gigabytes have on-board SIMG5723s connected to JMB ahcis. These are used to implement hardware raid. Unfortunately some firmware revisions on these 5723s don't bring the link down when all the downstream ports are unoccupied while not responding to reset protocol which makes libata think that there's device attached to the port but is not responding and retry. This results in painfully wrong boot detection time for these ports when they're empty. This patch quirks those boards such that ahci gives up after the initial timeout. Combined with parallel probing, this gives quick enough probing and also is safe because SIMG5723 will respond to the first try if any of the downstream ports is occupied. Signed-off-by: Tejun Heo Reported-by: Marc Bowes Reported-by: Nicolas Mailhot Signed-off-by: Jeff Garzik --- drivers/ata/ahci.c | 76 +++++++++++++++++++++++++++++++++++++++++++--- 1 file changed, 72 insertions(+), 4 deletions(-) diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c index 838ff73b08e..fe3eba5d6b3 100644 --- a/drivers/ata/ahci.c +++ b/drivers/ata/ahci.c @@ -219,6 +219,8 @@ enum { AHCI_HFLAG_SECT255 = (1 << 8), /* max 255 sectors */ AHCI_HFLAG_YES_NCQ = (1 << 9), /* force NCQ cap on */ AHCI_HFLAG_NO_SUSPEND = (1 << 10), /* don't suspend */ + AHCI_HFLAG_SRST_TOUT_IS_OFFLINE = (1 << 11), /* treat SRST timeout as + link offline */ /* ap->flags bits */ @@ -1663,6 +1665,7 @@ static int ahci_do_softreset(struct ata_link *link, unsigned int *class, int (*check_ready)(struct ata_link *link)) { struct ata_port *ap = link->ap; + struct ahci_host_priv *hpriv = ap->host->private_data; const char *reason = NULL; unsigned long now, msecs; struct ata_taskfile tf; @@ -1701,12 +1704,21 @@ static int ahci_do_softreset(struct ata_link *link, unsigned int *class, /* wait for link to become ready */ rc = ata_wait_after_reset(link, deadline, check_ready); - /* link occupied, -ENODEV too is an error */ - if (rc) { + if (rc == -EBUSY && hpriv->flags & AHCI_HFLAG_SRST_TOUT_IS_OFFLINE) { + /* + * Workaround for cases where link online status can't + * be trusted. Treat device readiness timeout as link + * offline. + */ + ata_link_printk(link, KERN_INFO, + "device not ready, treating as offline\n"); + *class = ATA_DEV_NONE; + } else if (rc) { + /* link occupied, -ENODEV too is an error */ reason = "device not ready"; goto fail; - } - *class = ahci_dev_classify(ap); + } else + *class = ahci_dev_classify(ap); DPRINTK("EXIT, class=%u\n", *class); return 0; @@ -2727,6 +2739,56 @@ static bool ahci_broken_suspend(struct pci_dev *pdev) return !ver || strcmp(ver, dmi->driver_data) < 0; } +static bool ahci_broken_online(struct pci_dev *pdev) +{ +#define ENCODE_BUSDEVFN(bus, slot, func) \ + (void *)(unsigned long)(((bus) << 8) | PCI_DEVFN((slot), (func))) + static const struct dmi_system_id sysids[] = { + /* + * There are several gigabyte boards which use + * SIMG5723s configured as hardware RAID. Certain + * 5723 firmware revisions shipped there keep the link + * online but fail to answer properly to SRST or + * IDENTIFY when no device is attached downstream + * causing libata to retry quite a few times leading + * to excessive detection delay. + * + * As these firmwares respond to the second reset try + * with invalid device signature, considering unknown + * sig as offline works around the problem acceptably. + */ + { + .ident = "EP45-DQ6", + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, + "Gigabyte Technology Co., Ltd."), + DMI_MATCH(DMI_BOARD_NAME, "EP45-DQ6"), + }, + .driver_data = ENCODE_BUSDEVFN(0x0a, 0x00, 0), + }, + { + .ident = "EP45-DS5", + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, + "Gigabyte Technology Co., Ltd."), + DMI_MATCH(DMI_BOARD_NAME, "EP45-DS5"), + }, + .driver_data = ENCODE_BUSDEVFN(0x03, 0x00, 0), + }, + { } /* terminate list */ + }; +#undef ENCODE_BUSDEVFN + const struct dmi_system_id *dmi = dmi_first_match(sysids); + unsigned int val; + + if (!dmi) + return false; + + val = (unsigned long)dmi->driver_data; + + return pdev->bus->number == (val >> 8) && pdev->devfn == (val & 0xff); +} + static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) { static int printed_version; @@ -2842,6 +2904,12 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) "BIOS update required for suspend/resume\n"); } + if (ahci_broken_online(pdev)) { + hpriv->flags |= AHCI_HFLAG_SRST_TOUT_IS_OFFLINE; + dev_info(&pdev->dev, + "online status unreliable, applying workaround\n"); + } + /* CAP.NP sometimes indicate the index of the last enabled * port, at other times, that of the last possible port, so * determining the maximum port number requires looking at -- GitLab From 67fe0688082509c52bd451d10a61b3565169c23e Mon Sep 17 00:00:00 2001 From: Jeff Garzik Date: Wed, 12 Aug 2009 06:29:57 -0400 Subject: [PATCH 1046/1342] Remove zero-length file drivers/mtd/maps/sbc8240.c It was "deleted" in commit 2bf961b7ccd69e108ac435c67e2b0522b403c578 Signed-off-by: Jeff Garzik --- drivers/mtd/maps/sbc8240.c | 0 1 file changed, 0 insertions(+), 0 deletions(-) delete mode 100644 drivers/mtd/maps/sbc8240.c diff --git a/drivers/mtd/maps/sbc8240.c b/drivers/mtd/maps/sbc8240.c deleted file mode 100644 index e69de29bb2d..00000000000 -- GitLab From 2a8083f063472f27c253545dd64e1a7bbbb1ab61 Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Tue, 11 Aug 2009 16:22:00 -0300 Subject: [PATCH 1047/1342] perf record: Fix .tid and .pid fill-in when synthesizing events MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Noticed when trying to record events for a firefox thread. We were synthesizing both .tid and .pid with the pid passed via --pid. Fix it by reading /proc/PID/status and getting the tgid to use in .pid, .tid gets the specified "pid". Signed-off-by: Arnaldo Carvalho de Melo Cc: "H. Peter Anvin" Cc: Frédéric Weisbecker Cc: Peter Zijlstra Cc: Mike Galbraith LKML-Reference: <20090811192200.GF18061@ghostprotocols.net> Signed-off-by: Ingo Molnar --- tools/perf/builtin-record.c | 71 ++++++++++++++++++++----------------- 1 file changed, 38 insertions(+), 33 deletions(-) diff --git a/tools/perf/builtin-record.c b/tools/perf/builtin-record.c index 0345aad8eba..30b83def03d 100644 --- a/tools/perf/builtin-record.c +++ b/tools/perf/builtin-record.c @@ -203,46 +203,48 @@ static void sig_atexit(void) kill(getpid(), signr); } -static void pid_synthesize_comm_event(pid_t pid, int full) +static pid_t pid_synthesize_comm_event(pid_t pid, int full) { struct comm_event comm_ev; char filename[PATH_MAX]; char bf[BUFSIZ]; - int fd; - size_t size; - char *field, *sep; + FILE *fp; + size_t size = 0; DIR *tasks; struct dirent dirent, *next; + pid_t tgid = 0; - snprintf(filename, sizeof(filename), "/proc/%d/stat", pid); + snprintf(filename, sizeof(filename), "/proc/%d/status", pid); - fd = open(filename, O_RDONLY); - if (fd < 0) { + fp = fopen(filename, "r"); + if (fd == NULL) { /* * We raced with a task exiting - just return: */ if (verbose) fprintf(stderr, "couldn't open %s\n", filename); - return; + return 0; } - if (read(fd, bf, sizeof(bf)) < 0) { - fprintf(stderr, "couldn't read %s\n", filename); - exit(EXIT_FAILURE); - } - close(fd); - /* 9027 (cat) R 6747 9027 6747 34816 9027 ... */ memset(&comm_ev, 0, sizeof(comm_ev)); - field = strchr(bf, '('); - if (field == NULL) - goto out_failure; - sep = strchr(++field, ')'); - if (sep == NULL) - goto out_failure; - size = sep - field; - memcpy(comm_ev.comm, field, size++); - - comm_ev.pid = pid; + while (!comm_ev.comm[0] || !comm_ev.pid) { + if (fgets(bf, sizeof(bf), fp) == NULL) + goto out_failure; + + if (memcmp(bf, "Name:", 5) == 0) { + char *name = bf + 5; + while (*name && isspace(*name)) + ++name; + size = strlen(name) - 1; + memcpy(comm_ev.comm, name, size++); + } else if (memcmp(bf, "Tgid:", 5) == 0) { + char *tgids = bf + 5; + while (*tgids && isspace(*tgids)) + ++tgids; + tgid = comm_ev.pid = atoi(tgids); + } + } + comm_ev.header.type = PERF_EVENT_COMM; size = ALIGN(size, sizeof(u64)); comm_ev.header.size = sizeof(comm_ev) - (sizeof(comm_ev.comm) - size); @@ -251,7 +253,7 @@ static void pid_synthesize_comm_event(pid_t pid, int full) comm_ev.tid = pid; write_output(&comm_ev, comm_ev.header.size); - return; + goto out_fclose; } snprintf(filename, sizeof(filename), "/proc/%d/task", pid); @@ -268,7 +270,10 @@ static void pid_synthesize_comm_event(pid_t pid, int full) write_output(&comm_ev, comm_ev.header.size); } closedir(tasks); - return; + +out_fclose: + fclose(fp); + return tgid; out_failure: fprintf(stderr, "couldn't get COMM and pgid, malformed %s\n", @@ -276,7 +281,7 @@ out_failure: exit(EXIT_FAILURE); } -static void pid_synthesize_mmap_samples(pid_t pid) +static void pid_synthesize_mmap_samples(pid_t pid, pid_t tgid) { char filename[PATH_MAX]; FILE *fp; @@ -328,7 +333,7 @@ static void pid_synthesize_mmap_samples(pid_t pid) mmap_ev.len -= mmap_ev.start; mmap_ev.header.size = (sizeof(mmap_ev) - (sizeof(mmap_ev.filename) - size)); - mmap_ev.pid = pid; + mmap_ev.pid = tgid; mmap_ev.tid = pid; write_output(&mmap_ev, mmap_ev.header.size); @@ -347,14 +352,14 @@ static void synthesize_all(void) while (!readdir_r(proc, &dirent, &next) && next) { char *end; - pid_t pid; + pid_t pid, tgid; pid = strtol(dirent.d_name, &end, 10); if (*end) /* only interested in proper numerical dirents */ continue; - pid_synthesize_comm_event(pid, 1); - pid_synthesize_mmap_samples(pid); + tgid = pid_synthesize_comm_event(pid, 1); + pid_synthesize_mmap_samples(pid, tgid); } closedir(proc); @@ -567,8 +572,8 @@ static int __cmd_record(int argc, const char **argv) perf_header__write(header, output); if (!system_wide) { - pid_synthesize_comm_event(pid, 0); - pid_synthesize_mmap_samples(pid); + pid_t tgid = pid_synthesize_comm_event(pid, 0); + pid_synthesize_mmap_samples(pid, tgid); } else synthesize_all(); -- GitLab From 94a24752fe95ca1e7f98b197052d44e6a207740d Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Tue, 11 Aug 2009 16:21:38 -0300 Subject: [PATCH 1048/1342] perf report: Show the tid too in -D MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This made it easier to find the firefox threading related bug. Signed-off-by: Arnaldo Carvalho de Melo Cc: "H. Peter Anvin" Cc: Peter Zijlstra Cc: Mike Galbraith Cc: Frédéric Weisbecker LKML-Reference: <20090811192138.GE18061@ghostprotocols.net> Signed-off-by: Ingo Molnar --- tools/perf/builtin-report.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c index 99274cec0ad..23e1457f240 100644 --- a/tools/perf/builtin-report.c +++ b/tools/perf/builtin-report.c @@ -1526,11 +1526,11 @@ process_sample_event(event_t *event, unsigned long offset, unsigned long head) more_data += sizeof(u64); } - dprintf("%p [%p]: PERF_EVENT_SAMPLE (IP, %d): %d: %p period: %Ld\n", + dprintf("%p [%p]: PERF_EVENT_SAMPLE (IP, %d): %d/%d: %p period: %Ld\n", (void *)(offset + head), (void *)(long)(event->header.size), event->header.misc, - event->ip.pid, + event->ip.pid, event->ip.tid, (void *)(long)ip, (long long)period); @@ -1612,10 +1612,11 @@ process_mmap_event(event_t *event, unsigned long offset, unsigned long head) struct thread *thread = threads__findnew(event->mmap.pid); struct map *map = map__new(&event->mmap); - dprintf("%p [%p]: PERF_EVENT_MMAP %d: [%p(%p) @ %p]: %s\n", + dprintf("%p [%p]: PERF_EVENT_MMAP %d/%d: [%p(%p) @ %p]: %s\n", (void *)(offset + head), (void *)(long)(event->header.size), event->mmap.pid, + event->mmap.tid, (void *)(long)event->mmap.start, (void *)(long)event->mmap.len, (void *)(long)event->mmap.pgoff, -- GitLab From 247648e3742ded01e42a4b14c2da330b13cbb47f Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Tue, 11 Aug 2009 16:22:11 -0300 Subject: [PATCH 1049/1342] perf tools: Fix fallback to cplus_demangle() when bfd_demangle() is not available MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit In old binutils we can't access bfd_demangle(), use cplus_demangle() just like oprofile. Signed-off-by: Arnaldo Carvalho de Melo Cc: Luis Claudio R. Gonçalves Cc: H. Peter Anvin Cc: Peter Zijlstra Cc: Mike Galbraith Cc: Frédéric Weisbecker LKML-Reference: <20090811192211.GG18061@ghostprotocols.net> Signed-off-by: Ingo Molnar --- tools/perf/Makefile | 29 ++++++++++++++++++----------- tools/perf/util/symbol.c | 15 --------------- tools/perf/util/symbol.h | 24 ++++++++++++++++++++++++ 3 files changed, 42 insertions(+), 26 deletions(-) diff --git a/tools/perf/Makefile b/tools/perf/Makefile index 60411e94113..c045b4271e5 100644 --- a/tools/perf/Makefile +++ b/tools/perf/Makefile @@ -382,22 +382,29 @@ endif ifdef NO_DEMANGLE BASIC_CFLAGS += -DNO_DEMANGLE else - has_bfd := $(shell sh -c "(echo '\#include '; echo 'int main(void) { bfd_demangle(0, 0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -lbfd > /dev/null 2>&1 && echo y") - has_bfd_iberty := $(shell sh -c "(echo '\#include '; echo 'int main(void) { bfd_demangle(0, 0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -lbfd -liberty > /dev/null 2>&1 && echo y") - - has_bfd_iberty_z := $(shell sh -c "(echo '\#include '; echo 'int main(void) { bfd_demangle(0, 0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -lbfd -liberty -lz > /dev/null 2>&1 && echo y") - ifeq ($(has_bfd),y) EXTLIBS += -lbfd - else ifeq ($(has_bfd_iberty),y) - EXTLIBS += -lbfd -liberty - else ifeq ($(has_bfd_iberty_z),y) - EXTLIBS += -lbfd -liberty -lz else - msg := $(warning No bfd.h/libbfd found, install binutils-dev[el] to gain symbol demangling) - BASIC_CFLAGS += -DNO_DEMANGLE + has_bfd_iberty := $(shell sh -c "(echo '\#include '; echo 'int main(void) { bfd_demangle(0, 0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -lbfd -liberty > /dev/null 2>&1 && echo y") + ifeq ($(has_bfd_iberty),y) + EXTLIBS += -lbfd -liberty + else + has_bfd_iberty_z := $(shell sh -c "(echo '\#include '; echo 'int main(void) { bfd_demangle(0, 0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -lbfd -liberty -lz > /dev/null 2>&1 && echo y") + ifeq ($(has_bfd_iberty_z),y) + EXTLIBS += -lbfd -liberty -lz + else + has_cplus_demangle := $(shell sh -c "(echo 'extern char *cplus_demangle(const char *, int);'; echo 'int main(void) { cplus_demangle(0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -liberty > /dev/null 2>&1 && echo y") + ifeq ($(has_cplus_demangle),y) + EXTLIBS += -liberty + BASIC_CFLAGS += -DHAVE_CPLUS_DEMANGLE + else + msg := $(warning No bfd.h/libbfd found, install binutils-dev[el] to gain symbol demangling) + BASIC_CFLAGS += -DNO_DEMANGLE + endif + endif + endif endif endif diff --git a/tools/perf/util/symbol.c b/tools/perf/util/symbol.c index f1dcede1430..2473fd427be 100644 --- a/tools/perf/util/symbol.c +++ b/tools/perf/util/symbol.c @@ -7,23 +7,8 @@ #include #include -#ifndef NO_DEMANGLE -#include -#else -static inline -char *bfd_demangle(void __used *v, const char __used *c, int __used i) -{ - return NULL; -} -#endif - const char *sym_hist_filter; -#ifndef DMGL_PARAMS -#define DMGL_PARAMS (1 << 0) /* Include function args */ -#define DMGL_ANSI (1 << 1) /* Include const, volatile, etc */ -#endif - enum dso_origin { DSO__ORIG_KERNEL = 0, DSO__ORIG_JAVA_JIT, diff --git a/tools/perf/util/symbol.h b/tools/perf/util/symbol.h index 1e003ec2f4b..b53bf0125c1 100644 --- a/tools/perf/util/symbol.h +++ b/tools/perf/util/symbol.h @@ -7,6 +7,30 @@ #include #include "module.h" +#ifdef HAVE_CPLUS_DEMANGLE +extern char *cplus_demangle(const char *, int); + +static inline char *bfd_demangle(void __used *v, const char *c, int i) +{ + return cplus_demangle(c, i); +} +#else +#ifdef NO_DEMANGLE +static inline char *bfd_demangle(void __used *v, const char __used *c, + int __used i) +{ + return NULL; +} +#else +#include +#endif +#endif + +#ifndef DMGL_PARAMS +#define DMGL_PARAMS (1 << 0) /* Include function args */ +#define DMGL_ANSI (1 << 1) /* Include const, volatile, etc */ +#endif + struct symbol { struct rb_node rb_node; u64 start; -- GitLab From 1340e6bbaff7ff7f6f75eb4a5c34933efce84a84 Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Tue, 11 Aug 2009 17:04:36 -0300 Subject: [PATCH 1050/1342] perf tools: Fix dso__new handle() to handle deleted DSOs MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit It is better than showing the map addr, this way at least we know that we can't get the symtabs because the DSO was deleted (system update) while an app still used such DSO. Yeah, don't do that, but if you do, you'll figure it out quicker this way. [acme@doppio linux-2.6-tip]$ perf report | head -15 # Samples: 3796 # # Overhead Command Shared Object Symbol # ........ ....... ................................................................... ...... # 23.55% pidgin /lib64/libglib-2.0.so.0.2000.4.#prelink#.Pd98lu (deleted) [.] 0x00000000038844 21.55% pidgin /lib64/libpthread-2.10.1.so.#prelink#.AFwK8Q (deleted) [.] 0x0000000000a42d 10.85% pidgin [kernel] [.] vread_hpet 7.85% pidgin /lib64/libgobject-2.0.so.0.2000.4.#prelink#.o1vpU7 (deleted) [.] 0x00000000014de8 3.35% pidgin /lib64/libc-2.10.1.so (deleted) [.] 0x0000000007a875 3.19% pidgin /lib64/libdbus-1.so.3.4.0.#prelink#.6mwgZP (deleted) [.] 0x0000000001d254 3.06% pidgin /usr/lib64/libgtk-x11-2.0.so.0.1600.5.#prelink#.511hAl (deleted) [.] 0x000000002334e7 2.90% pidgin /usr/lib64/libgdk-x11-2.0.so.0.1600.5.#prelink#.5qlMo1 (deleted) [.] 0x00000000037b2d 1.84% pidgin [kernel] [k] do_sys_poll 1.45% pidgin /usr/lib64/libX11.so.6.2.0.#prelink#.iR59Rx (deleted) [.] 0x0000000004c751 [acme@doppio linux-2.6-tip]$ Signed-off-by: Arnaldo Carvalho de Melo Cc: Luis Claudio R. Gonçalves Cc: Clark Williams Cc: H. Peter Anvin Cc: Peter Zijlstra Cc: Mike Galbraith Cc: Frédéric Weisbecker LKML-Reference: <20090811200436.GA3478@ghostprotocols.net> Signed-off-by: Ingo Molnar --- tools/perf/util/symbol.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/tools/perf/util/symbol.c b/tools/perf/util/symbol.c index 2473fd427be..5c0f42e6b33 100644 --- a/tools/perf/util/symbol.c +++ b/tools/perf/util/symbol.c @@ -801,6 +801,8 @@ more: } out: free(name); + if (ret < 0 && strstr(self->name, " (deleted)") != NULL) + return 0; return ret; } -- GitLab From 0a5ac84650fb7a7f226814103d95724e34b012ae Mon Sep 17 00:00:00 2001 From: Jens Axboe Date: Wed, 12 Aug 2009 11:18:01 +0200 Subject: [PATCH 1051/1342] perf record: Add missing -C option support for specifying profile cpu perf top supports a -C for setting the profile CPU, but perf record does not. This adds the same option for perf record, allowing the user to specify a specific target profile CPU. Signed-off-by: Jens Axboe Cc: Peter Zijlstra Cc: Mike Galbraith Cc: Paul Mackerras Cc: Arnaldo Carvalho de Melo Cc: Frederic Weisbecker LKML-Reference: <20090812091801.GC12579@kernel.dk> Signed-off-by: Ingo Molnar --- tools/perf/builtin-record.c | 17 ++++++++++++++--- 1 file changed, 14 insertions(+), 3 deletions(-) diff --git a/tools/perf/builtin-record.c b/tools/perf/builtin-record.c index 30b83def03d..de76008fbaa 100644 --- a/tools/perf/builtin-record.c +++ b/tools/perf/builtin-record.c @@ -35,6 +35,7 @@ static const char *output_name = "perf.data"; static int group = 0; static unsigned int realtime_prio = 0; static int system_wide = 0; +static int profile_cpu = -1; static pid_t target_pid = -1; static int inherit = 1; static int force = 0; @@ -431,6 +432,8 @@ try_again: if (err == EPERM) die("Permission error - are you root?\n"); + else if (err == ENODEV && profile_cpu != -1) + die("No such device - did you specify an out-of-range profile CPU?\n"); /* * If it's cycles then fall back to hrtimer @@ -564,9 +567,15 @@ static int __cmd_record(int argc, const char **argv) if (pid == -1) pid = getpid(); - open_counters(-1, pid); - } else for (i = 0; i < nr_cpus; i++) - open_counters(i, target_pid); + open_counters(profile_cpu, pid); + } else { + if (profile_cpu != -1) { + open_counters(profile_cpu, target_pid); + } else { + for (i = 0; i < nr_cpus; i++) + open_counters(i, target_pid); + } + } if (file_new) perf_header__write(header, output); @@ -645,6 +654,8 @@ static const struct option options[] = { "system-wide collection from all CPUs"), OPT_BOOLEAN('A', "append", &append_file, "append to the output file to do incremental profiling"), + OPT_INTEGER('C', "profile_cpu", &profile_cpu, + "CPU to profile on"), OPT_BOOLEAN('f', "force", &force, "overwrite existing data file"), OPT_LONG('c', "count", &default_interval, -- GitLab From 04da8a43da804723a550f00dd158fd5b5e25ae35 Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Tue, 11 Aug 2009 10:40:08 +0200 Subject: [PATCH 1052/1342] perf_counter, x86: Fix/improve apic fallback Johannes Stezenbach reported that his Pentium-M based laptop does not have the local APIC enabled by default, and hence perfcounters do not get initialized. Add a fallback for this case: allow non-sampled counters and return with an error on sampled counters. This allows 'perf stat' to work out of box - and allows 'perf top' and 'perf record' to fall back on a hrtimer based sampling method. ( Passing 'lapic' on the boot line will allow hardware sampling to occur - but if the APIC is disabled permanently by the hardware then this fallback still allows more systems to use perfcounters. ) Also decouple perfcounter support from X86_LOCAL_APIC. -v2: fix typo breaking counters on all other systems ... Reported-by: Johannes Stezenbach Cc: Peter Zijlstra Cc: Mike Galbraith Cc: Paul Mackerras Cc: Arnaldo Carvalho de Melo Cc: Frederic Weisbecker LKML-Reference: Signed-off-by: Ingo Molnar --- arch/x86/Kconfig | 2 +- arch/x86/kernel/cpu/perf_counter.c | 34 ++++++++++++++++++++++++++---- 2 files changed, 31 insertions(+), 5 deletions(-) diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index 738bdc6b0f8..13ffa5df37d 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -24,6 +24,7 @@ config X86 select HAVE_UNSTABLE_SCHED_CLOCK select HAVE_IDE select HAVE_OPROFILE + select HAVE_PERF_COUNTERS if (!M386 && !M486) select HAVE_IOREMAP_PROT select HAVE_KPROBES select ARCH_WANT_OPTIONAL_GPIOLIB @@ -742,7 +743,6 @@ config X86_UP_IOAPIC config X86_LOCAL_APIC def_bool y depends on X86_64 || SMP || X86_32_NON_STANDARD || X86_UP_APIC - select HAVE_PERF_COUNTERS if (!M386 && !M486) config X86_IO_APIC def_bool y diff --git a/arch/x86/kernel/cpu/perf_counter.c b/arch/x86/kernel/cpu/perf_counter.c index fffc126dbdf..900332b800f 100644 --- a/arch/x86/kernel/cpu/perf_counter.c +++ b/arch/x86/kernel/cpu/perf_counter.c @@ -55,6 +55,7 @@ struct x86_pmu { int num_counters_fixed; int counter_bits; u64 counter_mask; + int apic; u64 max_period; u64 intel_ctrl; }; @@ -613,6 +614,7 @@ static DEFINE_MUTEX(pmc_reserve_mutex); static bool reserve_pmc_hardware(void) { +#ifdef CONFIG_X86_LOCAL_APIC int i; if (nmi_watchdog == NMI_LOCAL_APIC) @@ -627,9 +629,11 @@ static bool reserve_pmc_hardware(void) if (!reserve_evntsel_nmi(x86_pmu.eventsel + i)) goto eventsel_fail; } +#endif return true; +#ifdef CONFIG_X86_LOCAL_APIC eventsel_fail: for (i--; i >= 0; i--) release_evntsel_nmi(x86_pmu.eventsel + i); @@ -644,10 +648,12 @@ perfctr_fail: enable_lapic_nmi_watchdog(); return false; +#endif } static void release_pmc_hardware(void) { +#ifdef CONFIG_X86_LOCAL_APIC int i; for (i = 0; i < x86_pmu.num_counters; i++) { @@ -657,6 +663,7 @@ static void release_pmc_hardware(void) if (nmi_watchdog == NMI_LOCAL_APIC) enable_lapic_nmi_watchdog(); +#endif } static void hw_perf_counter_destroy(struct perf_counter *counter) @@ -748,6 +755,15 @@ static int __hw_perf_counter_init(struct perf_counter *counter) hwc->sample_period = x86_pmu.max_period; hwc->last_period = hwc->sample_period; atomic64_set(&hwc->period_left, hwc->sample_period); + } else { + /* + * If we have a PMU initialized but no APIC + * interrupts, we cannot sample hardware + * counters (user-space has to fall back and + * sample via a hrtimer based software counter): + */ + if (!x86_pmu.apic) + return -EOPNOTSUPP; } counter->destroy = hw_perf_counter_destroy; @@ -1449,18 +1465,22 @@ void smp_perf_pending_interrupt(struct pt_regs *regs) void set_perf_counter_pending(void) { +#ifdef CONFIG_X86_LOCAL_APIC apic->send_IPI_self(LOCAL_PENDING_VECTOR); +#endif } void perf_counters_lapic_init(void) { - if (!x86_pmu_initialized()) +#ifdef CONFIG_X86_LOCAL_APIC + if (!x86_pmu.apic || !x86_pmu_initialized()) return; /* * Always use NMI for PMU */ apic_write(APIC_LVTPC, APIC_DM_NMI); +#endif } static int __kprobes @@ -1484,7 +1504,9 @@ perf_counter_nmi_handler(struct notifier_block *self, regs = args->regs; +#ifdef CONFIG_X86_LOCAL_APIC apic_write(APIC_LVTPC, APIC_DM_NMI); +#endif /* * Can't rely on the handled return value to say it was our NMI, two * counters could trigger 'simultaneously' raising two back-to-back NMIs. @@ -1515,6 +1537,7 @@ static struct x86_pmu p6_pmu = { .event_map = p6_pmu_event_map, .raw_event = p6_pmu_raw_event, .max_events = ARRAY_SIZE(p6_perfmon_event_map), + .apic = 1, .max_period = (1ULL << 31) - 1, .version = 0, .num_counters = 2, @@ -1541,6 +1564,7 @@ static struct x86_pmu intel_pmu = { .event_map = intel_pmu_event_map, .raw_event = intel_pmu_raw_event, .max_events = ARRAY_SIZE(intel_perfmon_event_map), + .apic = 1, /* * Intel PMCs cannot be accessed sanely above 32 bit width, * so we install an artificial 1<<31 period regardless of @@ -1564,6 +1588,7 @@ static struct x86_pmu amd_pmu = { .num_counters = 4, .counter_bits = 48, .counter_mask = (1ULL << 48) - 1, + .apic = 1, /* use highest bit to detect overflow */ .max_period = (1ULL << 47) - 1, }; @@ -1589,13 +1614,14 @@ static int p6_pmu_init(void) return -ENODEV; } + x86_pmu = p6_pmu; + if (!cpu_has_apic) { pr_info("no APIC, boot with the \"lapic\" boot parameter to force-enable it.\n"); - return -ENODEV; + pr_info("no hardware sampling interrupt available.\n"); + x86_pmu.apic = 0; } - x86_pmu = p6_pmu; - return 0; } -- GitLab From 1ae88b2e446261c038f2c0c3150ffae142b227a2 Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Wed, 12 Aug 2009 09:12:30 -0400 Subject: [PATCH 1053/1342] NFS: Fix an O_DIRECT Oops... We can't call nfs_readdata_release()/nfs_writedata_release() without first initialising and referencing args.context. Doing so inside nfs_direct_read_schedule_segment()/nfs_direct_write_schedule_segment() causes an Oops. We should rather be calling nfs_readdata_free()/nfs_writedata_free() in those cases. Looking at the O_DIRECT code, the "struct nfs_direct_req" is already referencing the nfs_open_context for us. Since the readdata and writedata structures carry a reference to that, we can simplify things by getting rid of the extra nfs_open_context references, so that we can replace all instances of nfs_readdata_release()/nfs_writedata_release(). Reported-by: Catalin Marinas Signed-off-by: Trond Myklebust Tested-by: Catalin Marinas Cc: stable@kernel.org Signed-off-by: Linus Torvalds --- fs/nfs/direct.c | 20 ++++++++++---------- fs/nfs/read.c | 6 ++---- fs/nfs/write.c | 6 ++---- include/linux/nfs_fs.h | 5 ++--- 4 files changed, 16 insertions(+), 21 deletions(-) diff --git a/fs/nfs/direct.c b/fs/nfs/direct.c index 489fc01a320..e4e089a8f29 100644 --- a/fs/nfs/direct.c +++ b/fs/nfs/direct.c @@ -255,7 +255,7 @@ static void nfs_direct_read_release(void *calldata) if (put_dreq(dreq)) nfs_direct_complete(dreq); - nfs_readdata_release(calldata); + nfs_readdata_free(data); } static const struct rpc_call_ops nfs_read_direct_ops = { @@ -314,14 +314,14 @@ static ssize_t nfs_direct_read_schedule_segment(struct nfs_direct_req *dreq, data->npages, 1, 0, data->pagevec, NULL); up_read(¤t->mm->mmap_sem); if (result < 0) { - nfs_readdata_release(data); + nfs_readdata_free(data); break; } if ((unsigned)result < data->npages) { bytes = result * PAGE_SIZE; if (bytes <= pgbase) { nfs_direct_release_pages(data->pagevec, result); - nfs_readdata_release(data); + nfs_readdata_free(data); break; } bytes -= pgbase; @@ -334,7 +334,7 @@ static ssize_t nfs_direct_read_schedule_segment(struct nfs_direct_req *dreq, data->inode = inode; data->cred = msg.rpc_cred; data->args.fh = NFS_FH(inode); - data->args.context = get_nfs_open_context(ctx); + data->args.context = ctx; data->args.offset = pos; data->args.pgbase = pgbase; data->args.pages = data->pagevec; @@ -441,7 +441,7 @@ static void nfs_direct_free_writedata(struct nfs_direct_req *dreq) struct nfs_write_data *data = list_entry(dreq->rewrite_list.next, struct nfs_write_data, pages); list_del(&data->pages); nfs_direct_release_pages(data->pagevec, data->npages); - nfs_writedata_release(data); + nfs_writedata_free(data); } } @@ -534,7 +534,7 @@ static void nfs_direct_commit_release(void *calldata) dprintk("NFS: %5u commit returned %d\n", data->task.tk_pid, status); nfs_direct_write_complete(dreq, data->inode); - nfs_commitdata_release(calldata); + nfs_commit_free(data); } static const struct rpc_call_ops nfs_commit_direct_ops = { @@ -570,7 +570,7 @@ static void nfs_direct_commit_schedule(struct nfs_direct_req *dreq) data->args.fh = NFS_FH(data->inode); data->args.offset = 0; data->args.count = 0; - data->args.context = get_nfs_open_context(dreq->ctx); + data->args.context = dreq->ctx; data->res.count = 0; data->res.fattr = &data->fattr; data->res.verf = &data->verf; @@ -734,14 +734,14 @@ static ssize_t nfs_direct_write_schedule_segment(struct nfs_direct_req *dreq, data->npages, 0, 0, data->pagevec, NULL); up_read(¤t->mm->mmap_sem); if (result < 0) { - nfs_writedata_release(data); + nfs_writedata_free(data); break; } if ((unsigned)result < data->npages) { bytes = result * PAGE_SIZE; if (bytes <= pgbase) { nfs_direct_release_pages(data->pagevec, result); - nfs_writedata_release(data); + nfs_writedata_free(data); break; } bytes -= pgbase; @@ -756,7 +756,7 @@ static ssize_t nfs_direct_write_schedule_segment(struct nfs_direct_req *dreq, data->inode = inode; data->cred = msg.rpc_cred; data->args.fh = NFS_FH(inode); - data->args.context = get_nfs_open_context(ctx); + data->args.context = ctx; data->args.offset = pos; data->args.pgbase = pgbase; data->args.pages = data->pagevec; diff --git a/fs/nfs/read.c b/fs/nfs/read.c index 73ea5e8d66c..12c9e66d3f1 100644 --- a/fs/nfs/read.c +++ b/fs/nfs/read.c @@ -60,17 +60,15 @@ struct nfs_read_data *nfs_readdata_alloc(unsigned int pagecount) return p; } -static void nfs_readdata_free(struct nfs_read_data *p) +void nfs_readdata_free(struct nfs_read_data *p) { if (p && (p->pagevec != &p->page_array[0])) kfree(p->pagevec); mempool_free(p, nfs_rdata_mempool); } -void nfs_readdata_release(void *data) +static void nfs_readdata_release(struct nfs_read_data *rdata) { - struct nfs_read_data *rdata = data; - put_nfs_open_context(rdata->args.context); nfs_readdata_free(rdata); } diff --git a/fs/nfs/write.c b/fs/nfs/write.c index 0a0a2ff767c..a34fae21fe1 100644 --- a/fs/nfs/write.c +++ b/fs/nfs/write.c @@ -87,17 +87,15 @@ struct nfs_write_data *nfs_writedata_alloc(unsigned int pagecount) return p; } -static void nfs_writedata_free(struct nfs_write_data *p) +void nfs_writedata_free(struct nfs_write_data *p) { if (p && (p->pagevec != &p->page_array[0])) kfree(p->pagevec); mempool_free(p, nfs_wdata_mempool); } -void nfs_writedata_release(void *data) +static void nfs_writedata_release(struct nfs_write_data *wdata) { - struct nfs_write_data *wdata = data; - put_nfs_open_context(wdata->args.context); nfs_writedata_free(wdata); } diff --git a/include/linux/nfs_fs.h b/include/linux/nfs_fs.h index fdffb413b19..f6b90240dd4 100644 --- a/include/linux/nfs_fs.h +++ b/include/linux/nfs_fs.h @@ -473,7 +473,6 @@ extern int nfs_writepages(struct address_space *, struct writeback_control *); extern int nfs_flush_incompatible(struct file *file, struct page *page); extern int nfs_updatepage(struct file *, struct page *, unsigned int, unsigned int); extern int nfs_writeback_done(struct rpc_task *, struct nfs_write_data *); -extern void nfs_writedata_release(void *); /* * Try to write back everything synchronously (but check the @@ -488,7 +487,6 @@ extern int nfs_wb_page_cancel(struct inode *inode, struct page* page); extern int nfs_commit_inode(struct inode *, int); extern struct nfs_write_data *nfs_commitdata_alloc(void); extern void nfs_commit_free(struct nfs_write_data *wdata); -extern void nfs_commitdata_release(void *wdata); #else static inline int nfs_commit_inode(struct inode *inode, int how) @@ -507,6 +505,7 @@ nfs_have_writebacks(struct inode *inode) * Allocate nfs_write_data structures */ extern struct nfs_write_data *nfs_writedata_alloc(unsigned int npages); +extern void nfs_writedata_free(struct nfs_write_data *); /* * linux/fs/nfs/read.c @@ -515,7 +514,6 @@ extern int nfs_readpage(struct file *, struct page *); extern int nfs_readpages(struct file *, struct address_space *, struct list_head *, unsigned); extern int nfs_readpage_result(struct rpc_task *, struct nfs_read_data *); -extern void nfs_readdata_release(void *data); extern int nfs_readpage_async(struct nfs_open_context *, struct inode *, struct page *); @@ -523,6 +521,7 @@ extern int nfs_readpage_async(struct nfs_open_context *, struct inode *, * Allocate nfs_read_data structures */ extern struct nfs_read_data *nfs_readdata_alloc(unsigned int npages); +extern void nfs_readdata_free(struct nfs_read_data *); /* * linux/fs/nfs3proc.c -- GitLab From 39cbb602b543e477df71dca84b5b2e36f8bd29fc Mon Sep 17 00:00:00 2001 From: "Alan D. Brunelle" Date: Fri, 7 Aug 2009 12:01:08 -0400 Subject: [PATCH 1054/1342] Remove double removal of blktrace directory commit fd51d251e4cdb21f68e9dbc4336514d64a105a79 Author: Stefan Raspl Date: Tue May 19 09:59:08 2009 +0200 blktrace: remove debugfs entries on bad path added in an explicit invocation of debugfs_remove for bt->dir, in blk_remove_buf_file_callback we are also getting the directory removed. On occasion I am seeing memory corruption that I have bisected down to this commit. [The testing involves a (long) series of I/O benchmarks with blktrace invoked around the actual runs.] I believe that this committed patch is correct, but the problem actually lies in the code in blk_remove_buf_file_callback. With this patch I am able to consistently get complete runs whereas previously I could not get a single run to complete. The first part of the patch simply moves the debugfs_remove below the relay_close: the relay_close call will remove files under bt->dir, and so we should not remove the directory until all the files we created have been removed. (Note: This is not sufficient to fix the problem - the file system code has ref counts on the directoy, so our invocation does not cause the directory to actually be removed. Nonetheless, we should not rely upon that feature.) Signed-off-by: Alan D. Brunelle Signed-off-by: Jens Axboe --- kernel/trace/blktrace.c | 12 +----------- 1 file changed, 1 insertion(+), 11 deletions(-) diff --git a/kernel/trace/blktrace.c b/kernel/trace/blktrace.c index 1090b0aed9b..7a34cb563fe 100644 --- a/kernel/trace/blktrace.c +++ b/kernel/trace/blktrace.c @@ -267,8 +267,8 @@ static void blk_trace_free(struct blk_trace *bt) { debugfs_remove(bt->msg_file); debugfs_remove(bt->dropped_file); - debugfs_remove(bt->dir); relay_close(bt->rchan); + debugfs_remove(bt->dir); free_percpu(bt->sequence); free_percpu(bt->msg_data); kfree(bt); @@ -378,18 +378,8 @@ static int blk_subbuf_start_callback(struct rchan_buf *buf, void *subbuf, static int blk_remove_buf_file_callback(struct dentry *dentry) { - struct dentry *parent = dentry->d_parent; debugfs_remove(dentry); - /* - * this will fail for all but the last file, but that is ok. what we - * care about is the top level buts->name directory going away, when - * the last trace file is gone. Then we don't have to rmdir() that - * manually on trace stop, so it nicely solves the issue with - * force killing of running traces. - */ - - debugfs_remove(parent); return 0; } -- GitLab From 51d5668cb2e3fd1827a55184e48606fff054c5be Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Thu, 13 Aug 2009 09:54:02 +1000 Subject: [PATCH 1055/1342] md: never advance 'events' counter by more than 1. When assembling arrays, md allows two devices to have different event counts as long as the difference is only '1'. This is to cope with a system failure between updating the metadata on two difference devices. However there are currently times when we update the event count by 2. This was done to keep the event count even when the array is clean and odd when it is dirty, which allows us to avoid writing common update to spare devices and so allow those spares to go to sleep. This is bad for the above reason. So change it to never increase by two. This means that the alignment between 'odd/even' and 'clean/dirty' might take a little longer to attain, but that is only a small cost. The spares will get a few more updates but that will still be spared (;-) most updates and can still go to sleep. Prior to this patch there was a small chance that after a crash an array would fail to assemble due to the overly large event count mismatch. Signed-off-by: NeilBrown --- drivers/md/md.c | 13 +++++-------- 1 file changed, 5 insertions(+), 8 deletions(-) diff --git a/drivers/md/md.c b/drivers/md/md.c index 5614500092e..d18805fea11 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -1975,17 +1975,14 @@ repeat: /* otherwise we have to go forward and ... */ mddev->events ++; if (!mddev->in_sync || mddev->recovery_cp != MaxSector) { /* not clean */ - /* .. if the array isn't clean, insist on an odd 'events' */ - if ((mddev->events&1)==0) { - mddev->events++; + /* .. if the array isn't clean, an 'even' event must also go + * to spares. */ + if ((mddev->events&1)==0) nospares = 0; - } } else { - /* otherwise insist on an even 'events' (for clean states) */ - if ((mddev->events&1)) { - mddev->events++; + /* otherwise an 'odd' event must go to spares */ + if ((mddev->events&1)) nospares = 0; - } } } -- GitLab From 67ac6011db5d2b0c853d573ff474b25c85dfb644 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Thu, 13 Aug 2009 10:06:24 +1000 Subject: [PATCH 1056/1342] md/raid5: allow new reshape modes to be restarted in the middle. md/raid5 doesn't allow a reshape to restart if it involves writing over the same part of disk that it would be reading from. This happens at the beginning of a reshape that increases the number of devices, at the end of a reshape that decreases the number of devices, and continuously for a reshape that does not change the number of devices. The current code is correct for the "increase number of devices" case as the critical section at the start is handled by userspace performing a backup. It does not work for reducing the number of devices, or the no-change case. For 'reducing', we need to invert the test. For no-change we cannot really be sure things will be safe, so simply require the array to be read-only, which is how the user-space code which carefully starts such arrays works. Signed-off-by: NeilBrown --- drivers/md/raid5.c | 21 ++++++++++++++++++++- 1 file changed, 20 insertions(+), 1 deletion(-) diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c index 2b521ee67df..b8a22a2205c 100644 --- a/drivers/md/raid5.c +++ b/drivers/md/raid5.c @@ -4509,7 +4509,26 @@ static int run(mddev_t *mddev) (old_disks-max_degraded)); /* here_old is the first stripe that we might need to read * from */ - if (here_new >= here_old) { + if (mddev->delta_disks == 0) { + /* We cannot be sure it is safe to start an in-place + * reshape. It is only safe if user-space if monitoring + * and taking constant backups. + * mdadm always starts a situation like this in + * readonly mode so it can take control before + * allowing any writes. So just check for that. + */ + if ((here_new * mddev->new_chunk_sectors != + here_old * mddev->chunk_sectors) || + mddev->ro == 0) { + printk(KERN_ERR "raid5: in-place reshape must be started" + " in read-only mode - aborting\n"); + return -EINVAL; + } + } else if (mddev->delta_disks < 0 + ? (here_new * mddev->new_chunk_sectors <= + here_old * mddev->chunk_sectors) + : (here_new * mddev->new_chunk_sectors >= + here_old * mddev->chunk_sectors)) { /* Reading from the same stripe as writing to - bad */ printk(KERN_ERR "raid5: reshape_position too early for " "auto-recovery - aborting.\n"); -- GitLab From a639755cf885e437b2fe4168d35157fa90d530ab Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Thu, 13 Aug 2009 10:13:00 +1000 Subject: [PATCH 1057/1342] md/raid5: make sure a reshape restarts at the correct address. This "if" don't allow for the possibility that the number of devices doesn't change, and so sector_nr isn't set correctly in that case. So change '>' to '>='. Signed-off-by: NeilBrown --- drivers/md/raid5.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c index b8a22a2205c..94a74cb5ccc 100644 --- a/drivers/md/raid5.c +++ b/drivers/md/raid5.c @@ -3785,7 +3785,7 @@ static sector_t reshape_request(mddev_t *mddev, sector_t sector_nr, int *skipped conf->reshape_progress < raid5_size(mddev, 0, 0)) { sector_nr = raid5_size(mddev, 0, 0) - conf->reshape_progress; - } else if (mddev->delta_disks > 0 && + } else if (mddev->delta_disks >= 0 && conf->reshape_progress > 0) sector_nr = conf->reshape_progress; sector_div(sector_nr, new_data_disks); -- GitLab From 9799218ae36910af50f002a5db1802d576fffb43 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Wed, 12 Aug 2009 17:37:52 -0700 Subject: [PATCH 1058/1342] Revert "libertas: Read buffer overflow" This reverts commit 57921c312e8cef72ba35a4cfe870b376da0b1b87. On request from John Linville: It has been shown to create a new problem. There is work towards a solution to that one, but it isn't a simple clean-up. Signed-off-by: David S. Miller --- drivers/net/wireless/libertas/assoc.c | 18 ++++++++++-------- 1 file changed, 10 insertions(+), 8 deletions(-) diff --git a/drivers/net/wireless/libertas/assoc.c b/drivers/net/wireless/libertas/assoc.c index d6997371c27..b9b37411903 100644 --- a/drivers/net/wireless/libertas/assoc.c +++ b/drivers/net/wireless/libertas/assoc.c @@ -1,7 +1,6 @@ /* Copyright (C) 2006, Red Hat, Inc. */ #include -#include #include #include #include @@ -44,21 +43,21 @@ static int get_common_rates(struct lbs_private *priv, u16 *rates_size) { u8 *card_rates = lbs_bg_rates; + size_t num_card_rates = sizeof(lbs_bg_rates); int ret = 0, i, j; - u8 tmp[(ARRAY_SIZE(lbs_bg_rates) - 1) * (*rates_size - 1)]; + u8 tmp[30]; size_t tmp_size = 0; /* For each rate in card_rates that exists in rate1, copy to tmp */ - for (i = 0; i < ARRAY_SIZE(lbs_bg_rates) && card_rates[i]; i++) { - for (j = 0; j < *rates_size && rates[j]; j++) { + for (i = 0; card_rates[i] && (i < num_card_rates); i++) { + for (j = 0; rates[j] && (j < *rates_size); j++) { if (rates[j] == card_rates[i]) tmp[tmp_size++] = card_rates[i]; } } lbs_deb_hex(LBS_DEB_JOIN, "AP rates ", rates, *rates_size); - lbs_deb_hex(LBS_DEB_JOIN, "card rates ", card_rates, - ARRAY_SIZE(lbs_bg_rates)); + lbs_deb_hex(LBS_DEB_JOIN, "card rates ", card_rates, num_card_rates); lbs_deb_hex(LBS_DEB_JOIN, "common rates", tmp, tmp_size); lbs_deb_join("TX data rate 0x%02x\n", priv->cur_rate); @@ -70,7 +69,10 @@ static int get_common_rates(struct lbs_private *priv, lbs_pr_alert("Previously set fixed data rate %#x isn't " "compatible with the network.\n", priv->cur_rate); ret = -1; + goto done; } + ret = 0; + done: memset(rates, 0, *rates_size); *rates_size = min_t(int, tmp_size, *rates_size); @@ -320,7 +322,7 @@ static int lbs_associate(struct lbs_private *priv, rates = (struct mrvl_ie_rates_param_set *) pos; rates->header.type = cpu_to_le16(TLV_TYPE_RATES); memcpy(&rates->rates, &bss->rates, MAX_RATES); - tmplen = min_t(u16, ARRAY_SIZE(rates->rates), MAX_RATES); + tmplen = MAX_RATES; if (get_common_rates(priv, rates->rates, &tmplen)) { ret = -1; goto done; @@ -596,7 +598,7 @@ static int lbs_adhoc_join(struct lbs_private *priv, /* Copy Data rates from the rates recorded in scan response */ memset(cmd.bss.rates, 0, sizeof(cmd.bss.rates)); - ratesize = min_t(u16, ARRAY_SIZE(cmd.bss.rates), MAX_RATES); + ratesize = min_t(u16, sizeof(cmd.bss.rates), MAX_RATES); memcpy(cmd.bss.rates, bss->rates, ratesize); if (get_common_rates(priv, cmd.bss.rates, &ratesize)) { lbs_deb_join("ADHOC_JOIN: get_common_rates returned error.\n"); -- GitLab From 1a67dde0abba36421a1257d01ba9de2f6d1c160a Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Thu, 13 Aug 2009 10:41:49 +1000 Subject: [PATCH 1059/1342] md/raid5: Properly remove excess drives after shrinking a raid5/6 We were removing the drives, from the array, but not removing symlinks from /sys/.... and not marking the device as having been removed. Signed-off-by: NeilBrown --- drivers/md/raid5.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-) diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c index 94a74cb5ccc..b8a2c5dc67b 100644 --- a/drivers/md/raid5.c +++ b/drivers/md/raid5.c @@ -5097,8 +5097,15 @@ static void raid5_finish_reshape(mddev_t *mddev) mddev->degraded--; for (d = conf->raid_disks ; d < conf->raid_disks - mddev->delta_disks; - d++) - raid5_remove_disk(mddev, d); + d++) { + mdk_rdev_t *rdev = conf->disks[d].rdev; + if (rdev && raid5_remove_disk(mddev, d) == 0) { + char nm[20]; + sprintf(nm, "rd%d", rdev->raid_disk); + sysfs_remove_link(&mddev->kobj, nm); + rdev->raid_disk = -1; + } + } } mddev->layout = conf->algorithm; mddev->chunk_sectors = conf->chunk_sectors; -- GitLab From 4d484a4a7a5126410eed5f8dd329a33f6eeed068 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Thu, 13 Aug 2009 10:41:50 +1000 Subject: [PATCH 1060/1342] md: allow upper limit for resync/reshape to be set when array is read-only Normally we only allow the upper limit for a reshape to be decreased when the array not performing a sync/recovery/reshape, otherwise there could be races. But if an array is part-way through a reshape when it is assembled the reshape is started immediately leaving no window to set an upper bound. If the array is started read-only, the reshape will be suspended until the array becomes writable, so that provides a window during which it is perfectly safe to reduce the upper limit of a reshape. So: allow the upper limit (sync_max) to be reduced even if the reshape thread is running, as long as the array is still read-only. Signed-off-by: NeilBrown --- drivers/md/md.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/md/md.c b/drivers/md/md.c index d18805fea11..103f2d33fa8 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -3599,6 +3599,7 @@ max_sync_store(mddev_t *mddev, const char *buf, size_t len) if (max < mddev->resync_min) return -EINVAL; if (max < mddev->resync_max && + mddev->ro == 0 && test_bit(MD_RECOVERY_RUNNING, &mddev->recovery)) return -EBUSY; -- GitLab From ba9a633787eed1e90d587282642580ad3d44f7fd Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Wed, 22 Jul 2009 15:14:29 +0000 Subject: [PATCH 1061/1342] sh: convert processor device setup functions to arch_initcall() Convert the processor platform device setup functions from __initcall() and sometimes device_initcall() to arch_initcall(). This makes sure that the platform devices are registered a bit earlier so the devices are available when drivers register using initcall levels earlier than device_initcall(). A good example is platform devices needed by i2c-sh_mobile.c which registers a bit earlier using subsys_initcall(). Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt --- arch/sh/kernel/cpu/sh2/setup-sh7619.c | 2 +- arch/sh/kernel/cpu/sh2a/setup-mxg.c | 2 +- arch/sh/kernel/cpu/sh2a/setup-sh7201.c | 2 +- arch/sh/kernel/cpu/sh2a/setup-sh7203.c | 2 +- arch/sh/kernel/cpu/sh2a/setup-sh7206.c | 2 +- arch/sh/kernel/cpu/sh3/setup-sh7705.c | 2 +- arch/sh/kernel/cpu/sh3/setup-sh770x.c | 2 +- arch/sh/kernel/cpu/sh3/setup-sh7710.c | 2 +- arch/sh/kernel/cpu/sh3/setup-sh7720.c | 2 +- arch/sh/kernel/cpu/sh4/setup-sh4-202.c | 2 +- arch/sh/kernel/cpu/sh4/setup-sh7750.c | 2 +- arch/sh/kernel/cpu/sh4/setup-sh7760.c | 2 +- arch/sh/kernel/cpu/sh4a/setup-sh7343.c | 2 +- arch/sh/kernel/cpu/sh4a/setup-sh7366.c | 2 +- arch/sh/kernel/cpu/sh4a/setup-sh7722.c | 2 +- arch/sh/kernel/cpu/sh4a/setup-sh7723.c | 2 +- arch/sh/kernel/cpu/sh4a/setup-sh7724.c | 2 +- arch/sh/kernel/cpu/sh4a/setup-sh7763.c | 2 +- arch/sh/kernel/cpu/sh4a/setup-sh7770.c | 2 +- arch/sh/kernel/cpu/sh4a/setup-sh7780.c | 2 +- arch/sh/kernel/cpu/sh4a/setup-sh7785.c | 2 +- arch/sh/kernel/cpu/sh4a/setup-sh7786.c | 2 +- arch/sh/kernel/cpu/sh4a/setup-shx3.c | 2 +- arch/sh/kernel/cpu/sh5/setup-sh5.c | 2 +- 24 files changed, 24 insertions(+), 24 deletions(-) diff --git a/arch/sh/kernel/cpu/sh2/setup-sh7619.c b/arch/sh/kernel/cpu/sh2/setup-sh7619.c index 13798733f2d..8555c05e866 100644 --- a/arch/sh/kernel/cpu/sh2/setup-sh7619.c +++ b/arch/sh/kernel/cpu/sh2/setup-sh7619.c @@ -187,7 +187,7 @@ static int __init sh7619_devices_setup(void) return platform_add_devices(sh7619_devices, ARRAY_SIZE(sh7619_devices)); } -__initcall(sh7619_devices_setup); +arch_initcall(sh7619_devices_setup); void __init plat_irq_setup(void) { diff --git a/arch/sh/kernel/cpu/sh2a/setup-mxg.c b/arch/sh/kernel/cpu/sh2a/setup-mxg.c index 869c2da4820..b6737644531 100644 --- a/arch/sh/kernel/cpu/sh2a/setup-mxg.c +++ b/arch/sh/kernel/cpu/sh2a/setup-mxg.c @@ -238,7 +238,7 @@ static int __init mxg_devices_setup(void) return platform_add_devices(mxg_devices, ARRAY_SIZE(mxg_devices)); } -__initcall(mxg_devices_setup); +arch_initcall(mxg_devices_setup); void __init plat_irq_setup(void) { diff --git a/arch/sh/kernel/cpu/sh2a/setup-sh7201.c b/arch/sh/kernel/cpu/sh2a/setup-sh7201.c index d8febe12806..fbde5b75deb 100644 --- a/arch/sh/kernel/cpu/sh2a/setup-sh7201.c +++ b/arch/sh/kernel/cpu/sh2a/setup-sh7201.c @@ -357,7 +357,7 @@ static int __init sh7201_devices_setup(void) return platform_add_devices(sh7201_devices, ARRAY_SIZE(sh7201_devices)); } -__initcall(sh7201_devices_setup); +arch_initcall(sh7201_devices_setup); void __init plat_irq_setup(void) { diff --git a/arch/sh/kernel/cpu/sh2a/setup-sh7203.c b/arch/sh/kernel/cpu/sh2a/setup-sh7203.c index 62e3039d239..d3fd536c9a8 100644 --- a/arch/sh/kernel/cpu/sh2a/setup-sh7203.c +++ b/arch/sh/kernel/cpu/sh2a/setup-sh7203.c @@ -367,7 +367,7 @@ static int __init sh7203_devices_setup(void) return platform_add_devices(sh7203_devices, ARRAY_SIZE(sh7203_devices)); } -__initcall(sh7203_devices_setup); +arch_initcall(sh7203_devices_setup); void __init plat_irq_setup(void) { diff --git a/arch/sh/kernel/cpu/sh2a/setup-sh7206.c b/arch/sh/kernel/cpu/sh2a/setup-sh7206.c index 3e6f3d7a58b..a9ccc5e8d9e 100644 --- a/arch/sh/kernel/cpu/sh2a/setup-sh7206.c +++ b/arch/sh/kernel/cpu/sh2a/setup-sh7206.c @@ -338,7 +338,7 @@ static int __init sh7206_devices_setup(void) return platform_add_devices(sh7206_devices, ARRAY_SIZE(sh7206_devices)); } -__initcall(sh7206_devices_setup); +arch_initcall(sh7206_devices_setup); void __init plat_irq_setup(void) { diff --git a/arch/sh/kernel/cpu/sh3/setup-sh7705.c b/arch/sh/kernel/cpu/sh3/setup-sh7705.c index 88f742fed9e..c2310598387 100644 --- a/arch/sh/kernel/cpu/sh3/setup-sh7705.c +++ b/arch/sh/kernel/cpu/sh3/setup-sh7705.c @@ -222,7 +222,7 @@ static int __init sh7705_devices_setup(void) return platform_add_devices(sh7705_devices, ARRAY_SIZE(sh7705_devices)); } -__initcall(sh7705_devices_setup); +arch_initcall(sh7705_devices_setup); static struct platform_device *sh7705_early_devices[] __initdata = { &tmu0_device, diff --git a/arch/sh/kernel/cpu/sh3/setup-sh770x.c b/arch/sh/kernel/cpu/sh3/setup-sh770x.c index c5630679858..347ab35d069 100644 --- a/arch/sh/kernel/cpu/sh3/setup-sh770x.c +++ b/arch/sh/kernel/cpu/sh3/setup-sh770x.c @@ -250,7 +250,7 @@ static int __init sh770x_devices_setup(void) return platform_add_devices(sh770x_devices, ARRAY_SIZE(sh770x_devices)); } -__initcall(sh770x_devices_setup); +arch_initcall(sh770x_devices_setup); static struct platform_device *sh770x_early_devices[] __initdata = { &tmu0_device, diff --git a/arch/sh/kernel/cpu/sh3/setup-sh7710.c b/arch/sh/kernel/cpu/sh3/setup-sh7710.c index efa76c8148f..717e90ae109 100644 --- a/arch/sh/kernel/cpu/sh3/setup-sh7710.c +++ b/arch/sh/kernel/cpu/sh3/setup-sh7710.c @@ -226,7 +226,7 @@ static int __init sh7710_devices_setup(void) return platform_add_devices(sh7710_devices, ARRAY_SIZE(sh7710_devices)); } -__initcall(sh7710_devices_setup); +arch_initcall(sh7710_devices_setup); static struct platform_device *sh7710_early_devices[] __initdata = { &tmu0_device, diff --git a/arch/sh/kernel/cpu/sh3/setup-sh7720.c b/arch/sh/kernel/cpu/sh3/setup-sh7720.c index 5b2107798ed..74d8baaf8e9 100644 --- a/arch/sh/kernel/cpu/sh3/setup-sh7720.c +++ b/arch/sh/kernel/cpu/sh3/setup-sh7720.c @@ -388,7 +388,7 @@ static int __init sh7720_devices_setup(void) return platform_add_devices(sh7720_devices, ARRAY_SIZE(sh7720_devices)); } -__initcall(sh7720_devices_setup); +arch_initcall(sh7720_devices_setup); static struct platform_device *sh7720_early_devices[] __initdata = { &cmt0_device, diff --git a/arch/sh/kernel/cpu/sh4/setup-sh4-202.c b/arch/sh/kernel/cpu/sh4/setup-sh4-202.c index 6d088d12359..de4827df19a 100644 --- a/arch/sh/kernel/cpu/sh4/setup-sh4-202.c +++ b/arch/sh/kernel/cpu/sh4/setup-sh4-202.c @@ -138,7 +138,7 @@ static int __init sh4202_devices_setup(void) return platform_add_devices(sh4202_devices, ARRAY_SIZE(sh4202_devices)); } -__initcall(sh4202_devices_setup); +arch_initcall(sh4202_devices_setup); static struct platform_device *sh4202_early_devices[] __initdata = { &tmu0_device, diff --git a/arch/sh/kernel/cpu/sh4/setup-sh7750.c b/arch/sh/kernel/cpu/sh4/setup-sh7750.c index 851672d15cf..1b8b122e8f3 100644 --- a/arch/sh/kernel/cpu/sh4/setup-sh7750.c +++ b/arch/sh/kernel/cpu/sh4/setup-sh7750.c @@ -239,7 +239,7 @@ static int __init sh7750_devices_setup(void) return platform_add_devices(sh7750_devices, ARRAY_SIZE(sh7750_devices)); } -__initcall(sh7750_devices_setup); +arch_initcall(sh7750_devices_setup); static struct platform_device *sh7750_early_devices[] __initdata = { &tmu0_device, diff --git a/arch/sh/kernel/cpu/sh4/setup-sh7760.c b/arch/sh/kernel/cpu/sh4/setup-sh7760.c index 5b822519bd9..7fbb7be9284 100644 --- a/arch/sh/kernel/cpu/sh4/setup-sh7760.c +++ b/arch/sh/kernel/cpu/sh4/setup-sh7760.c @@ -265,7 +265,7 @@ static int __init sh7760_devices_setup(void) return platform_add_devices(sh7760_devices, ARRAY_SIZE(sh7760_devices)); } -__initcall(sh7760_devices_setup); +arch_initcall(sh7760_devices_setup); static struct platform_device *sh7760_early_devices[] __initdata = { &tmu0_device, diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7343.c b/arch/sh/kernel/cpu/sh4a/setup-sh7343.c index 6307e087c86..ac4d5672ec1 100644 --- a/arch/sh/kernel/cpu/sh4a/setup-sh7343.c +++ b/arch/sh/kernel/cpu/sh4a/setup-sh7343.c @@ -325,7 +325,7 @@ static int __init sh7343_devices_setup(void) return platform_add_devices(sh7343_devices, ARRAY_SIZE(sh7343_devices)); } -__initcall(sh7343_devices_setup); +arch_initcall(sh7343_devices_setup); static struct platform_device *sh7343_early_devices[] __initdata = { &cmt_device, diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7366.c b/arch/sh/kernel/cpu/sh4a/setup-sh7366.c index c18f7d09281..1a956b1becc 100644 --- a/arch/sh/kernel/cpu/sh4a/setup-sh7366.c +++ b/arch/sh/kernel/cpu/sh4a/setup-sh7366.c @@ -318,7 +318,7 @@ static int __init sh7366_devices_setup(void) return platform_add_devices(sh7366_devices, ARRAY_SIZE(sh7366_devices)); } -__initcall(sh7366_devices_setup); +arch_initcall(sh7366_devices_setup); static struct platform_device *sh7366_early_devices[] __initdata = { &cmt_device, diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7722.c b/arch/sh/kernel/cpu/sh4a/setup-sh7722.c index ea524a2da3e..cda76ebf87c 100644 --- a/arch/sh/kernel/cpu/sh4a/setup-sh7722.c +++ b/arch/sh/kernel/cpu/sh4a/setup-sh7722.c @@ -359,7 +359,7 @@ static int __init sh7722_devices_setup(void) return platform_add_devices(sh7722_devices, ARRAY_SIZE(sh7722_devices)); } -__initcall(sh7722_devices_setup); +arch_initcall(sh7722_devices_setup); static struct platform_device *sh7722_early_devices[] __initdata = { &cmt_device, diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7723.c b/arch/sh/kernel/cpu/sh4a/setup-sh7723.c index e1bb80b2a27..b45dace9539 100644 --- a/arch/sh/kernel/cpu/sh4a/setup-sh7723.c +++ b/arch/sh/kernel/cpu/sh4a/setup-sh7723.c @@ -473,7 +473,7 @@ static int __init sh7723_devices_setup(void) return platform_add_devices(sh7723_devices, ARRAY_SIZE(sh7723_devices)); } -__initcall(sh7723_devices_setup); +arch_initcall(sh7723_devices_setup); static struct platform_device *sh7723_early_devices[] __initdata = { &cmt_device, diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7724.c b/arch/sh/kernel/cpu/sh4a/setup-sh7724.c index e5ac9eb11c6..a04edaab9a2 100644 --- a/arch/sh/kernel/cpu/sh4a/setup-sh7724.c +++ b/arch/sh/kernel/cpu/sh4a/setup-sh7724.c @@ -508,7 +508,7 @@ static int __init sh7724_devices_setup(void) return platform_add_devices(sh7724_devices, ARRAY_SIZE(sh7724_devices)); } -device_initcall(sh7724_devices_setup); +arch_initcall(sh7724_devices_setup); static struct platform_device *sh7724_early_devices[] __initdata = { &cmt_device, diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7763.c b/arch/sh/kernel/cpu/sh4a/setup-sh7763.c index f1e0c0d36da..4659fff6b84 100644 --- a/arch/sh/kernel/cpu/sh4a/setup-sh7763.c +++ b/arch/sh/kernel/cpu/sh4a/setup-sh7763.c @@ -314,7 +314,7 @@ static int __init sh7763_devices_setup(void) return platform_add_devices(sh7763_devices, ARRAY_SIZE(sh7763_devices)); } -__initcall(sh7763_devices_setup); +arch_initcall(sh7763_devices_setup); static struct platform_device *sh7763_early_devices[] __initdata = { &tmu0_device, diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7770.c b/arch/sh/kernel/cpu/sh4a/setup-sh7770.c index 1e86209db28..eead08d89d3 100644 --- a/arch/sh/kernel/cpu/sh4a/setup-sh7770.c +++ b/arch/sh/kernel/cpu/sh4a/setup-sh7770.c @@ -368,7 +368,7 @@ static int __init sh7770_devices_setup(void) return platform_add_devices(sh7770_devices, ARRAY_SIZE(sh7770_devices)); } -__initcall(sh7770_devices_setup); +arch_initcall(sh7770_devices_setup); static struct platform_device *sh7770_early_devices[] __initdata = { &tmu0_device, diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7780.c b/arch/sh/kernel/cpu/sh4a/setup-sh7780.c index 715e05b431e..2c901f44695 100644 --- a/arch/sh/kernel/cpu/sh4a/setup-sh7780.c +++ b/arch/sh/kernel/cpu/sh4a/setup-sh7780.c @@ -256,7 +256,7 @@ static int __init sh7780_devices_setup(void) return platform_add_devices(sh7780_devices, ARRAY_SIZE(sh7780_devices)); } -__initcall(sh7780_devices_setup); +arch_initcall(sh7780_devices_setup); static struct platform_device *sh7780_early_devices[] __initdata = { &tmu0_device, diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7785.c b/arch/sh/kernel/cpu/sh4a/setup-sh7785.c index af561402570..7f6c718b6c3 100644 --- a/arch/sh/kernel/cpu/sh4a/setup-sh7785.c +++ b/arch/sh/kernel/cpu/sh4a/setup-sh7785.c @@ -263,7 +263,7 @@ static int __init sh7785_devices_setup(void) return platform_add_devices(sh7785_devices, ARRAY_SIZE(sh7785_devices)); } -__initcall(sh7785_devices_setup); +arch_initcall(sh7785_devices_setup); static struct platform_device *sh7785_early_devices[] __initdata = { &tmu0_device, diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7786.c b/arch/sh/kernel/cpu/sh4a/setup-sh7786.c index b70049470a0..0104a8ec536 100644 --- a/arch/sh/kernel/cpu/sh4a/setup-sh7786.c +++ b/arch/sh/kernel/cpu/sh4a/setup-sh7786.c @@ -547,7 +547,7 @@ static int __init sh7786_devices_setup(void) return platform_add_devices(sh7786_devices, ARRAY_SIZE(sh7786_devices)); } -device_initcall(sh7786_devices_setup); +arch_initcall(sh7786_devices_setup); void __init plat_early_device_setup(void) { diff --git a/arch/sh/kernel/cpu/sh4a/setup-shx3.c b/arch/sh/kernel/cpu/sh4a/setup-shx3.c index 53c65fd9cce..07f078961c7 100644 --- a/arch/sh/kernel/cpu/sh4a/setup-shx3.c +++ b/arch/sh/kernel/cpu/sh4a/setup-shx3.c @@ -256,7 +256,7 @@ static int __init shx3_devices_setup(void) return platform_add_devices(shx3_devices, ARRAY_SIZE(shx3_devices)); } -__initcall(shx3_devices_setup); +arch_initcall(shx3_devices_setup); void __init plat_early_device_setup(void) { diff --git a/arch/sh/kernel/cpu/sh5/setup-sh5.c b/arch/sh/kernel/cpu/sh5/setup-sh5.c index f5ff1ac57fc..6a0f82f7003 100644 --- a/arch/sh/kernel/cpu/sh5/setup-sh5.c +++ b/arch/sh/kernel/cpu/sh5/setup-sh5.c @@ -186,7 +186,7 @@ static int __init sh5_devices_setup(void) return platform_add_devices(sh5_devices, ARRAY_SIZE(sh5_devices)); } -__initcall(sh5_devices_setup); +arch_initcall(sh5_devices_setup); void __init plat_early_device_setup(void) { -- GitLab From ba3a17019181af5d6ab898760620c4e9916396c2 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Thu, 13 Aug 2009 11:39:02 +0900 Subject: [PATCH 1062/1342] sh: fix i2c init order on Migo-R V2 Convert the Migo-R board code to register devices at arch_initcall() time instead of __initcall(). This fix unbreaks migor_ts touch screen driver support. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt --- arch/sh/boards/mach-migor/setup.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/sh/boards/mach-migor/setup.c b/arch/sh/boards/mach-migor/setup.c index f70f4644deb..f9b2e4df35b 100644 --- a/arch/sh/boards/mach-migor/setup.c +++ b/arch/sh/boards/mach-migor/setup.c @@ -608,7 +608,7 @@ static int __init migor_devices_setup(void) return platform_add_devices(migor_devices, ARRAY_SIZE(migor_devices)); } -__initcall(migor_devices_setup); +arch_initcall(migor_devices_setup); /* Return the board specific boot mode pin configuration */ static int migor_mode_pins(void) -- GitLab From dbefd606a3b3634799b625f4900336e61c89e868 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Fri, 7 Aug 2009 03:52:18 +0000 Subject: [PATCH 1063/1342] sh: fix i2c init order on ap325rxa V2 Convert the AP325RXA board code to register devices at arch_initcall() time instead of device_initcall(). This fix unbreaks pcf8563 RTC driver support. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt --- arch/sh/boards/board-ap325rxa.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/sh/boards/board-ap325rxa.c b/arch/sh/boards/board-ap325rxa.c index 7ffd1b4315b..b9c88cc519e 100644 --- a/arch/sh/boards/board-ap325rxa.c +++ b/arch/sh/boards/board-ap325rxa.c @@ -547,7 +547,7 @@ static int __init ap325rxa_devices_setup(void) return platform_add_devices(ap325rxa_devices, ARRAY_SIZE(ap325rxa_devices)); } -device_initcall(ap325rxa_devices_setup); +arch_initcall(ap325rxa_devices_setup); /* Return the board specific boot mode pin configuration */ static int ap325rxa_mode_pins(void) -- GitLab From 839d1624b9dcf31fdc02e47359043bb7bd71d6ca Mon Sep 17 00:00:00 2001 From: Francois Romieu Date: Wed, 12 Aug 2009 22:18:14 -0700 Subject: [PATCH 1064/1342] 8139cp: balance dma_map_single vs dma_unmap_single pair The driver always: 1. allocate cp->rx_buf_sz + NET_IP_ALIGN 2. map cp->rx_buf_sz Signed-off-by: Francois Romieu Signed-off-by: David S. Miller --- drivers/net/8139cp.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) diff --git a/drivers/net/8139cp.c b/drivers/net/8139cp.c index 50efde11ea6..d0dbbf39349 100644 --- a/drivers/net/8139cp.c +++ b/drivers/net/8139cp.c @@ -515,7 +515,7 @@ rx_status_loop: dma_addr_t mapping; struct sk_buff *skb, *new_skb; struct cp_desc *desc; - unsigned buflen; + const unsigned buflen = cp->rx_buf_sz; skb = cp->rx_skb[rx_tail]; BUG_ON(!skb); @@ -549,8 +549,7 @@ rx_status_loop: pr_debug("%s: rx slot %d status 0x%x len %d\n", dev->name, rx_tail, status, len); - buflen = cp->rx_buf_sz + NET_IP_ALIGN; - new_skb = netdev_alloc_skb(dev, buflen); + new_skb = netdev_alloc_skb(dev, buflen + NET_IP_ALIGN); if (!new_skb) { dev->stats.rx_dropped++; goto rx_next; -- GitLab From 8f7a0dc51674ad0dd06155291b0aed60d655943c Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Wed, 12 Aug 2009 14:44:59 -0300 Subject: [PATCH 1065/1342] perf list: Fix large list output by using the pager When /sys/kernel/debug is mounted the list can be imense, so use the pager like the other tools. Signed-off-by: Arnaldo Carvalho de Melo Acked-by: Frederic Weisbecker Cc: Peter Zijlstra LKML-Reference: <20090812174459.GB3495@ghostprotocols.net> Signed-off-by: Ingo Molnar --- tools/perf/builtin-list.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/tools/perf/builtin-list.c b/tools/perf/builtin-list.c index f990fa8a35c..d88c6961274 100644 --- a/tools/perf/builtin-list.c +++ b/tools/perf/builtin-list.c @@ -10,11 +10,12 @@ #include "perf.h" -#include "util/parse-options.h" #include "util/parse-events.h" +#include "util/cache.h" int cmd_list(int argc __used, const char **argv __used, const char *prefix __used) { + setup_pager(); print_events(); return 0; } -- GitLab From 28402971d869e26271b25301011f667d3a5640c3 Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Thu, 13 Aug 2009 10:13:22 +0200 Subject: [PATCH 1066/1342] perf_counter: Provide hw_perf_counter_setup_online() APIs Provide weak aliases for hw_perf_counter_setup_online(). This is used by the BTS patches (for v2.6.32), but it interacts with fixes so propagate this upstream. (it has no effect as of yet) Also export perf_counter_output() to architecture code. Cc: Peter Zijlstra Cc: Paul Mackerras Cc: Frederic Weisbecker LKML-Reference: Signed-off-by: Ingo Molnar --- include/linux/perf_counter.h | 2 ++ kernel/perf_counter.c | 10 +++++++++- 2 files changed, 11 insertions(+), 1 deletion(-) diff --git a/include/linux/perf_counter.h b/include/linux/perf_counter.h index a9d823a93fe..2b36afe6ae0 100644 --- a/include/linux/perf_counter.h +++ b/include/linux/perf_counter.h @@ -694,6 +694,8 @@ struct perf_sample_data { extern int perf_counter_overflow(struct perf_counter *counter, int nmi, struct perf_sample_data *data); +extern void perf_counter_output(struct perf_counter *counter, int nmi, + struct perf_sample_data *data); /* * Return 1 for a software counter, 0 for a hardware counter diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index b0b20a07f39..e26d2fcfa32 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -88,6 +88,7 @@ void __weak hw_perf_disable(void) { barrier(); } void __weak hw_perf_enable(void) { barrier(); } void __weak hw_perf_counter_setup(int cpu) { barrier(); } +void __weak hw_perf_counter_setup_online(int cpu) { barrier(); } int __weak hw_perf_group_sched_in(struct perf_counter *group_leader, @@ -2630,7 +2631,7 @@ static u32 perf_counter_tid(struct perf_counter *counter, struct task_struct *p) return task_pid_nr_ns(p, counter->ns); } -static void perf_counter_output(struct perf_counter *counter, int nmi, +void perf_counter_output(struct perf_counter *counter, int nmi, struct perf_sample_data *data) { int ret; @@ -4592,6 +4593,11 @@ perf_cpu_notify(struct notifier_block *self, unsigned long action, void *hcpu) perf_counter_init_cpu(cpu); break; + case CPU_ONLINE: + case CPU_ONLINE_FROZEN: + hw_perf_counter_setup_online(cpu); + break; + case CPU_DOWN_PREPARE: case CPU_DOWN_PREPARE_FROZEN: perf_counter_exit_cpu(cpu); @@ -4616,6 +4622,8 @@ void __init perf_counter_init(void) { perf_cpu_notify(&perf_cpu_nb, (unsigned long)CPU_UP_PREPARE, (void *)(long)smp_processor_id()); + perf_cpu_notify(&perf_cpu_nb, (unsigned long)CPU_ONLINE, + (void *)(long)smp_processor_id()); register_cpu_notifier(&perf_cpu_nb); } -- GitLab From 3a9f131fb00b8ac5950a11ad1599e45edfb5ae44 Mon Sep 17 00:00:00 2001 From: Frederic Weisbecker Date: Thu, 13 Aug 2009 10:27:18 +0200 Subject: [PATCH 1067/1342] perf tools: Add a per tracepoint counter attribute to get raw sample Add a new flag field while opening a tracepoint perf counter: -e tracepoint_subsystem:tracepoint_name:flags This is intended to be generic although for now it only supports the r[e[c[o[r[d]]]]] flag: ./perf record -e workqueue:workqueue_insertion:record ./perf record -e workqueue:workqueue_insertion:r will have the same effect: enabling the raw samples record for the given tracepoint counter. In the future, we may want to support further flags, separated by commas. Signed-off-by: Frederic Weisbecker Cc: Peter Zijlstra Cc: Arnaldo Carvalho de Melo Cc: Mike Galbraith LKML-Reference: <1250152039-7284-1-git-send-email-fweisbec@gmail.com> Signed-off-by: Ingo Molnar --- tools/perf/builtin-record.c | 2 +- tools/perf/util/parse-events.c | 10 ++++++++++ 2 files changed, 11 insertions(+), 1 deletion(-) diff --git a/tools/perf/builtin-record.c b/tools/perf/builtin-record.c index de76008fbaa..78adc47da86 100644 --- a/tools/perf/builtin-record.c +++ b/tools/perf/builtin-record.c @@ -398,7 +398,7 @@ static void create_counter(int counter, int cpu, pid_t pid) PERF_FORMAT_TOTAL_TIME_RUNNING | PERF_FORMAT_ID; - attr->sample_type = PERF_SAMPLE_IP | PERF_SAMPLE_TID; + attr->sample_type |= PERF_SAMPLE_IP | PERF_SAMPLE_TID; if (freq) { attr->sample_type |= PERF_SAMPLE_PERIOD; diff --git a/tools/perf/util/parse-events.c b/tools/perf/util/parse-events.c index 4858d83b3b6..04417840878 100644 --- a/tools/perf/util/parse-events.c +++ b/tools/perf/util/parse-events.c @@ -379,6 +379,7 @@ static int parse_tracepoint_event(const char **strp, struct perf_counter_attr *attr) { const char *evt_name; + char *flags; char sys_name[MAX_EVENT_LENGTH]; char id_buf[4]; int fd; @@ -400,6 +401,15 @@ static int parse_tracepoint_event(const char **strp, strncpy(sys_name, *strp, sys_length); sys_name[sys_length] = '\0'; evt_name = evt_name + 1; + + flags = strchr(evt_name, ':'); + if (flags) { + *flags = '\0'; + flags++; + if (!strncmp(flags, "record", strlen(flags))) + attr->sample_type |= PERF_SAMPLE_RAW; + } + evt_length = strlen(evt_name); if (evt_length >= MAX_EVENT_LENGTH) return 0; -- GitLab From daac07b2e6b77f1bd44104aa2f0593e5505f27d4 Mon Sep 17 00:00:00 2001 From: Frederic Weisbecker Date: Thu, 13 Aug 2009 10:27:19 +0200 Subject: [PATCH 1068/1342] perf tools: Add a general option to enable raw sample records While we can enable the perf sample records per tracepoint counter, we may also want to enable this option for every tracepoint counters to open, so that we don't need to add a :record flag for all of them. Add the -R, --raw-samples options for this purpose. Signed-off-by: Frederic Weisbecker Cc: Peter Zijlstra Cc: Arnaldo Carvalho de Melo Cc: Mike Galbraith LKML-Reference: <1250152039-7284-2-git-send-email-fweisbec@gmail.com> Signed-off-by: Ingo Molnar --- tools/perf/builtin-record.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/tools/perf/builtin-record.c b/tools/perf/builtin-record.c index 78adc47da86..3d051b9cf25 100644 --- a/tools/perf/builtin-record.c +++ b/tools/perf/builtin-record.c @@ -34,6 +34,7 @@ static int output; static const char *output_name = "perf.data"; static int group = 0; static unsigned int realtime_prio = 0; +static int raw_samples = 0; static int system_wide = 0; static int profile_cpu = -1; static pid_t target_pid = -1; @@ -418,6 +419,8 @@ static void create_counter(int counter, int cpu, pid_t pid) if (call_graph) attr->sample_type |= PERF_SAMPLE_CALLCHAIN; + if (raw_samples) + attr->sample_type |= PERF_SAMPLE_RAW; attr->mmap = track; attr->comm = track; @@ -650,6 +653,8 @@ static const struct option options[] = { "record events on existing pid"), OPT_INTEGER('r', "realtime", &realtime_prio, "collect data with this RT SCHED_FIFO priority"), + OPT_BOOLEAN('R', "raw-samples", &raw_samples, + "collect raw sample records from all opened counters"), OPT_BOOLEAN('a', "all-cpus", &system_wide, "system-wide collection from all CPUs"), OPT_BOOLEAN('A', "append", &append_file, -- GitLab From 8fd101f20bdf771949a8f3a5a779877d09b2fb56 Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Wed, 12 Aug 2009 18:19:57 -0300 Subject: [PATCH 1069/1342] perf report: Don't show unresolved DSOs and symbols when -S/-d is used We're interested in just those symbols/DSOs, so filter out the unresolved ones. Signed-off-by: Arnaldo Carvalho de Melo Cc: Peter Zijlstra LKML-Reference: <20090812211957.GE3495@ghostprotocols.net> Signed-off-by: Ingo Molnar --- tools/perf/builtin-report.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c index 23e1457f240..b53a60fc12d 100644 --- a/tools/perf/builtin-report.c +++ b/tools/perf/builtin-report.c @@ -1590,10 +1590,11 @@ process_sample_event(event_t *event, unsigned long offset, unsigned long head) if (show & show_mask) { struct symbol *sym = resolve_symbol(thread, &map, &dso, &ip); - if (dso_list && dso && dso->name && !strlist__has_entry(dso_list, dso->name)) + if (dso_list && (!dso || !dso->name || + !strlist__has_entry(dso_list, dso->name))) return 0; - if (sym_list && sym && !strlist__has_entry(sym_list, sym->name)) + if (sym_list && (!sym || !strlist__has_entry(sym_list, sym->name))) return 0; if (hist_entry__add(thread, map, dso, sym, ip, chain, level, period)) { -- GitLab From bcfc2602e8541ac13b1def38e2591dca072cff7a Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Thu, 13 Aug 2009 09:51:55 +0200 Subject: [PATCH 1070/1342] perf_counter: Fix swcounter context invariance perf_swcounter_is_counting() uses a lock, which means we cannot use swcounters from NMI or when holding that particular lock, this is unintended. The below removes the lock, this opens up race window, but not worse than the swcounters already experience due to RCU traversal of the context in perf_swcounter_ctx_event(). This also fixes the hard lockups while opening a lockdep tracepoint counter. Signed-off-by: Peter Zijlstra Acked-by: Frederic Weisbecker Cc: Paul Mackerras Cc: stephane eranian Cc: Corey J Ashford LKML-Reference: <1250149915.10001.66.camel@twins> Signed-off-by: Ingo Molnar --- kernel/perf_counter.c | 44 ++++++++++++++++++------------------------- 1 file changed, 18 insertions(+), 26 deletions(-) diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index e26d2fcfa32..3dd4339589a 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -3444,40 +3444,32 @@ static void perf_swcounter_add(struct perf_counter *counter, u64 nr, static int perf_swcounter_is_counting(struct perf_counter *counter) { - struct perf_counter_context *ctx; - unsigned long flags; - int count; - + /* + * The counter is active, we're good! + */ if (counter->state == PERF_COUNTER_STATE_ACTIVE) return 1; + /* + * The counter is off/error, not counting. + */ if (counter->state != PERF_COUNTER_STATE_INACTIVE) return 0; /* - * If the counter is inactive, it could be just because - * its task is scheduled out, or because it's in a group - * which could not go on the PMU. We want to count in - * the first case but not the second. If the context is - * currently active then an inactive software counter must - * be the second case. If it's not currently active then - * we need to know whether the counter was active when the - * context was last active, which we can determine by - * comparing counter->tstamp_stopped with ctx->time. - * - * We are within an RCU read-side critical section, - * which protects the existence of *ctx. + * The counter is inactive, if the context is active + * we're part of a group that didn't make it on the 'pmu', + * not counting. */ - ctx = counter->ctx; - spin_lock_irqsave(&ctx->lock, flags); - count = 1; - /* Re-check state now we have the lock */ - if (counter->state < PERF_COUNTER_STATE_INACTIVE || - counter->ctx->is_active || - counter->tstamp_stopped < ctx->time) - count = 0; - spin_unlock_irqrestore(&ctx->lock, flags); - return count; + if (counter->ctx->is_active) + return 0; + + /* + * We're inactive and the context is too, this means the + * task is scheduled out, we're counting events that happen + * to us, like migration events. + */ + return 1; } static int perf_swcounter_match(struct perf_counter *counter, -- GitLab From 3dab77fb1bf89664bb1c9544607159dcab6f7d57 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Thu, 13 Aug 2009 11:47:53 +0200 Subject: [PATCH 1071/1342] perf: Rework/fix the whole read vs group stuff Replace PERF_SAMPLE_GROUP with PERF_SAMPLE_READ and introduce PERF_FORMAT_GROUP to deal with group reads in a more generic way. This allows you to get group reads out of read() as well. Signed-off-by: Peter Zijlstra Cc: Corey J Ashford Cc: Paul Mackerras Cc: stephane eranian LKML-Reference: <20090813103655.117411814@chello.nl> Signed-off-by: Ingo Molnar --- include/linux/perf_counter.h | 47 ++++-- kernel/perf_counter.c | 274 ++++++++++++++++++++++++++--------- 2 files changed, 238 insertions(+), 83 deletions(-) diff --git a/include/linux/perf_counter.h b/include/linux/perf_counter.h index 2b36afe6ae0..b53f7006cc4 100644 --- a/include/linux/perf_counter.h +++ b/include/linux/perf_counter.h @@ -115,7 +115,7 @@ enum perf_counter_sample_format { PERF_SAMPLE_TID = 1U << 1, PERF_SAMPLE_TIME = 1U << 2, PERF_SAMPLE_ADDR = 1U << 3, - PERF_SAMPLE_GROUP = 1U << 4, + PERF_SAMPLE_READ = 1U << 4, PERF_SAMPLE_CALLCHAIN = 1U << 5, PERF_SAMPLE_ID = 1U << 6, PERF_SAMPLE_CPU = 1U << 7, @@ -127,16 +127,32 @@ enum perf_counter_sample_format { }; /* - * Bits that can be set in attr.read_format to request that - * reads on the counter should return the indicated quantities, - * in increasing order of bit value, after the counter value. + * The format of the data returned by read() on a perf counter fd, + * as specified by attr.read_format: + * + * struct read_format { + * { u64 value; + * { u64 time_enabled; } && PERF_FORMAT_ENABLED + * { u64 time_running; } && PERF_FORMAT_RUNNING + * { u64 id; } && PERF_FORMAT_ID + * } && !PERF_FORMAT_GROUP + * + * { u64 nr; + * { u64 time_enabled; } && PERF_FORMAT_ENABLED + * { u64 time_running; } && PERF_FORMAT_RUNNING + * { u64 value; + * { u64 id; } && PERF_FORMAT_ID + * } cntr[nr]; + * } && PERF_FORMAT_GROUP + * }; */ enum perf_counter_read_format { PERF_FORMAT_TOTAL_TIME_ENABLED = 1U << 0, PERF_FORMAT_TOTAL_TIME_RUNNING = 1U << 1, PERF_FORMAT_ID = 1U << 2, + PERF_FORMAT_GROUP = 1U << 3, - PERF_FORMAT_MAX = 1U << 3, /* non-ABI */ + PERF_FORMAT_MAX = 1U << 4, /* non-ABI */ }; #define PERF_ATTR_SIZE_VER0 64 /* sizeof first published struct */ @@ -343,10 +359,8 @@ enum perf_event_type { * struct { * struct perf_event_header header; * u32 pid, tid; - * u64 value; - * { u64 time_enabled; } && PERF_FORMAT_ENABLED - * { u64 time_running; } && PERF_FORMAT_RUNNING - * { u64 parent_id; } && PERF_FORMAT_ID + * + * struct read_format values; * }; */ PERF_EVENT_READ = 8, @@ -364,11 +378,22 @@ enum perf_event_type { * { u32 cpu, res; } && PERF_SAMPLE_CPU * { u64 period; } && PERF_SAMPLE_PERIOD * - * { u64 nr; - * { u64 id, val; } cnt[nr]; } && PERF_SAMPLE_GROUP + * { struct read_format values; } && PERF_SAMPLE_READ * * { u64 nr, * u64 ips[nr]; } && PERF_SAMPLE_CALLCHAIN + * + * # + * # The RAW record below is opaque data wrt the ABI + * # + * # That is, the ABI doesn't make any promises wrt to + * # the stability of its content, it may vary depending + * # on event, hardware, kernel version and phase of + * # the moon. + * # + * # In other words, PERF_SAMPLE_RAW contents are not an ABI. + * # + * * { u32 size; * char data[size];}&& PERF_SAMPLE_RAW * }; diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index 3dd4339589a..b8c6b97a20a 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -1692,7 +1692,32 @@ static int perf_release(struct inode *inode, struct file *file) return 0; } -static u64 perf_counter_read_tree(struct perf_counter *counter) +static int perf_counter_read_size(struct perf_counter *counter) +{ + int entry = sizeof(u64); /* value */ + int size = 0; + int nr = 1; + + if (counter->attr.read_format & PERF_FORMAT_TOTAL_TIME_ENABLED) + size += sizeof(u64); + + if (counter->attr.read_format & PERF_FORMAT_TOTAL_TIME_RUNNING) + size += sizeof(u64); + + if (counter->attr.read_format & PERF_FORMAT_ID) + entry += sizeof(u64); + + if (counter->attr.read_format & PERF_FORMAT_GROUP) { + nr += counter->group_leader->nr_siblings; + size += sizeof(u64); + } + + size += entry * nr; + + return size; +} + +static u64 perf_counter_read_value(struct perf_counter *counter) { struct perf_counter *child; u64 total = 0; @@ -1704,14 +1729,96 @@ static u64 perf_counter_read_tree(struct perf_counter *counter) return total; } +static int perf_counter_read_entry(struct perf_counter *counter, + u64 read_format, char __user *buf) +{ + int n = 0, count = 0; + u64 values[2]; + + values[n++] = perf_counter_read_value(counter); + if (read_format & PERF_FORMAT_ID) + values[n++] = primary_counter_id(counter); + + count = n * sizeof(u64); + + if (copy_to_user(buf, values, count)) + return -EFAULT; + + return count; +} + +static int perf_counter_read_group(struct perf_counter *counter, + u64 read_format, char __user *buf) +{ + struct perf_counter *leader = counter->group_leader, *sub; + int n = 0, size = 0, err = -EFAULT; + u64 values[3]; + + values[n++] = 1 + leader->nr_siblings; + if (read_format & PERF_FORMAT_TOTAL_TIME_ENABLED) { + values[n++] = leader->total_time_enabled + + atomic64_read(&leader->child_total_time_enabled); + } + if (read_format & PERF_FORMAT_TOTAL_TIME_RUNNING) { + values[n++] = leader->total_time_running + + atomic64_read(&leader->child_total_time_running); + } + + size = n * sizeof(u64); + + if (copy_to_user(buf, values, size)) + return -EFAULT; + + err = perf_counter_read_entry(leader, read_format, buf + size); + if (err < 0) + return err; + + size += err; + + list_for_each_entry(sub, &leader->sibling_list, list_entry) { + err = perf_counter_read_entry(counter, read_format, + buf + size); + if (err < 0) + return err; + + size += err; + } + + return size; +} + +static int perf_counter_read_one(struct perf_counter *counter, + u64 read_format, char __user *buf) +{ + u64 values[4]; + int n = 0; + + values[n++] = perf_counter_read_value(counter); + if (read_format & PERF_FORMAT_TOTAL_TIME_ENABLED) { + values[n++] = counter->total_time_enabled + + atomic64_read(&counter->child_total_time_enabled); + } + if (read_format & PERF_FORMAT_TOTAL_TIME_RUNNING) { + values[n++] = counter->total_time_running + + atomic64_read(&counter->child_total_time_running); + } + if (read_format & PERF_FORMAT_ID) + values[n++] = primary_counter_id(counter); + + if (copy_to_user(buf, values, n * sizeof(u64))) + return -EFAULT; + + return n * sizeof(u64); +} + /* * Read the performance counter - simple non blocking version for now */ static ssize_t perf_read_hw(struct perf_counter *counter, char __user *buf, size_t count) { - u64 values[4]; - int n; + u64 read_format = counter->attr.read_format; + int ret; /* * Return end-of-file for a read on a counter that is in @@ -1721,28 +1828,18 @@ perf_read_hw(struct perf_counter *counter, char __user *buf, size_t count) if (counter->state == PERF_COUNTER_STATE_ERROR) return 0; + if (count < perf_counter_read_size(counter)) + return -ENOSPC; + WARN_ON_ONCE(counter->ctx->parent_ctx); mutex_lock(&counter->child_mutex); - values[0] = perf_counter_read_tree(counter); - n = 1; - if (counter->attr.read_format & PERF_FORMAT_TOTAL_TIME_ENABLED) - values[n++] = counter->total_time_enabled + - atomic64_read(&counter->child_total_time_enabled); - if (counter->attr.read_format & PERF_FORMAT_TOTAL_TIME_RUNNING) - values[n++] = counter->total_time_running + - atomic64_read(&counter->child_total_time_running); - if (counter->attr.read_format & PERF_FORMAT_ID) - values[n++] = primary_counter_id(counter); + if (read_format & PERF_FORMAT_GROUP) + ret = perf_counter_read_group(counter, read_format, buf); + else + ret = perf_counter_read_one(counter, read_format, buf); mutex_unlock(&counter->child_mutex); - if (count < n * sizeof(u64)) - return -EINVAL; - count = n * sizeof(u64); - - if (copy_to_user(buf, values, count)) - return -EFAULT; - - return count; + return ret; } static ssize_t @@ -2631,6 +2728,79 @@ static u32 perf_counter_tid(struct perf_counter *counter, struct task_struct *p) return task_pid_nr_ns(p, counter->ns); } +static void perf_output_read_one(struct perf_output_handle *handle, + struct perf_counter *counter) +{ + u64 read_format = counter->attr.read_format; + u64 values[4]; + int n = 0; + + values[n++] = atomic64_read(&counter->count); + if (read_format & PERF_FORMAT_TOTAL_TIME_ENABLED) { + values[n++] = counter->total_time_enabled + + atomic64_read(&counter->child_total_time_enabled); + } + if (read_format & PERF_FORMAT_TOTAL_TIME_RUNNING) { + values[n++] = counter->total_time_running + + atomic64_read(&counter->child_total_time_running); + } + if (read_format & PERF_FORMAT_ID) + values[n++] = primary_counter_id(counter); + + perf_output_copy(handle, values, n * sizeof(u64)); +} + +/* + * XXX PERF_FORMAT_GROUP vs inherited counters seems difficult. + */ +static void perf_output_read_group(struct perf_output_handle *handle, + struct perf_counter *counter) +{ + struct perf_counter *leader = counter->group_leader, *sub; + u64 read_format = counter->attr.read_format; + u64 values[5]; + int n = 0; + + values[n++] = 1 + leader->nr_siblings; + + if (read_format & PERF_FORMAT_TOTAL_TIME_ENABLED) + values[n++] = leader->total_time_enabled; + + if (read_format & PERF_FORMAT_TOTAL_TIME_RUNNING) + values[n++] = leader->total_time_running; + + if (leader != counter) + leader->pmu->read(leader); + + values[n++] = atomic64_read(&leader->count); + if (read_format & PERF_FORMAT_ID) + values[n++] = primary_counter_id(leader); + + perf_output_copy(handle, values, n * sizeof(u64)); + + list_for_each_entry(sub, &leader->sibling_list, list_entry) { + n = 0; + + if (sub != counter) + sub->pmu->read(sub); + + values[n++] = atomic64_read(&sub->count); + if (read_format & PERF_FORMAT_ID) + values[n++] = primary_counter_id(sub); + + perf_output_copy(handle, values, n * sizeof(u64)); + } +} + +static void perf_output_read(struct perf_output_handle *handle, + struct perf_counter *counter) +{ + if (counter->attr.read_format & PERF_FORMAT_GROUP) + perf_output_read_group(handle, counter); + else + perf_output_read_one(handle, counter); +} + void perf_counter_output(struct perf_counter *counter, int nmi, struct perf_sample_data *data) { @@ -2642,10 +2812,6 @@ void perf_counter_output(struct perf_counter *counter, int nmi, struct { u32 pid, tid; } tid_entry; - struct { - u64 id; - u64 counter; - } group_entry; struct perf_callchain_entry *callchain = NULL; int callchain_size = 0; u64 time; @@ -2700,10 +2866,8 @@ void perf_counter_output(struct perf_counter *counter, int nmi, if (sample_type & PERF_SAMPLE_PERIOD) header.size += sizeof(u64); - if (sample_type & PERF_SAMPLE_GROUP) { - header.size += sizeof(u64) + - counter->nr_siblings * sizeof(group_entry); - } + if (sample_type & PERF_SAMPLE_READ) + header.size += perf_counter_read_size(counter); if (sample_type & PERF_SAMPLE_CALLCHAIN) { callchain = perf_callchain(data->regs); @@ -2760,26 +2924,8 @@ void perf_counter_output(struct perf_counter *counter, int nmi, if (sample_type & PERF_SAMPLE_PERIOD) perf_output_put(&handle, data->period); - /* - * XXX PERF_SAMPLE_GROUP vs inherited counters seems difficult. - */ - if (sample_type & PERF_SAMPLE_GROUP) { - struct perf_counter *leader, *sub; - u64 nr = counter->nr_siblings; - - perf_output_put(&handle, nr); - - leader = counter->group_leader; - list_for_each_entry(sub, &leader->sibling_list, list_entry) { - if (sub != counter) - sub->pmu->read(sub); - - group_entry.id = primary_counter_id(sub); - group_entry.counter = atomic64_read(&sub->count); - - perf_output_put(&handle, group_entry); - } - } + if (sample_type & PERF_SAMPLE_READ) + perf_output_read(&handle, counter); if (sample_type & PERF_SAMPLE_CALLCHAIN) { if (callchain) @@ -2818,8 +2964,6 @@ struct perf_read_event { u32 pid; u32 tid; - u64 value; - u64 format[3]; }; static void @@ -2831,34 +2975,20 @@ perf_counter_read_event(struct perf_counter *counter, .header = { .type = PERF_EVENT_READ, .misc = 0, - .size = sizeof(event) - sizeof(event.format), + .size = sizeof(event) + perf_counter_read_size(counter), }, .pid = perf_counter_pid(counter, task), .tid = perf_counter_tid(counter, task), - .value = atomic64_read(&counter->count), }; - int ret, i = 0; - - if (counter->attr.read_format & PERF_FORMAT_TOTAL_TIME_ENABLED) { - event.header.size += sizeof(u64); - event.format[i++] = counter->total_time_enabled; - } - - if (counter->attr.read_format & PERF_FORMAT_TOTAL_TIME_RUNNING) { - event.header.size += sizeof(u64); - event.format[i++] = counter->total_time_running; - } - - if (counter->attr.read_format & PERF_FORMAT_ID) { - event.header.size += sizeof(u64); - event.format[i++] = primary_counter_id(counter); - } + int ret; ret = perf_output_begin(&handle, counter, event.header.size, 0, 0); if (ret) return; - perf_output_copy(&handle, &event, event.header.size); + perf_output_put(&handle, event); + perf_output_read(&handle, counter); + perf_output_end(&handle); } @@ -3921,9 +4051,9 @@ perf_counter_alloc(struct perf_counter_attr *attr, atomic64_set(&hwc->period_left, hwc->sample_period); /* - * we currently do not support PERF_SAMPLE_GROUP on inherited counters + * we currently do not support PERF_FORMAT_GROUP on inherited counters */ - if (attr->inherit && (attr->sample_type & PERF_SAMPLE_GROUP)) + if (attr->inherit && (attr->read_format & PERF_FORMAT_GROUP)) goto done; switch (attr->type) { -- GitLab From 970892a9031a5dc7217bd394fb9d89fa75a4a7bc Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Thu, 13 Aug 2009 11:47:54 +0200 Subject: [PATCH 1072/1342] perf_counter: Fix an ipi-deadlock perf_pending_counter() is called from IRQ context and will call perf_counter_disable(), however perf_counter_disable() uses smp_call_function_single() which doesn't fancy being used with IRQs disabled due to IPI deadlocks. Fix this by making it use the local __perf_counter_disable() call and teaching the counter_sched_out() code about pending disables as well. This should cover the case where a counter migrates before the pending queue gets processed. Signed-off-by: Peter Zijlstra Cc: Corey J Ashford Cc: Paul Mackerras Cc: stephane eranian LKML-Reference: <20090813103655.244097721@chello.nl> Signed-off-by: Ingo Molnar --- kernel/perf_counter.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index b8c6b97a20a..3f841beefc7 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -307,6 +307,10 @@ counter_sched_out(struct perf_counter *counter, return; counter->state = PERF_COUNTER_STATE_INACTIVE; + if (counter->pending_disable) { + counter->pending_disable = 0; + counter->state = PERF_COUNTER_STATE_OFF; + } counter->tstamp_stopped = ctx->time; counter->pmu->disable(counter); counter->oncpu = -1; @@ -2343,7 +2347,7 @@ static void perf_pending_counter(struct perf_pending_entry *entry) if (counter->pending_disable) { counter->pending_disable = 0; - perf_counter_disable(counter); + __perf_counter_disable(counter); } if (counter->pending_wakeup) { -- GitLab From 94d5d1b2d891f1fd5205f978246b7864d998b25c Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Thu, 13 Aug 2009 16:14:42 +0200 Subject: [PATCH 1073/1342] perf_counter: Report the cloning task as parent on perf_counter_fork() A bug in (9f498cc: perf_counter: Full task tracing) makes profiling multi-threaded apps it go belly up. [ output as: (PID:TID):(PPID:PTID) ] # ./perf report -D | grep FORK 0x4b0 [0x18]: PERF_EVENT_FORK: (3237:3237):(3236:3236) 0xa10 [0x18]: PERF_EVENT_FORK: (3237:3238):(3236:3236) 0xa70 [0x18]: PERF_EVENT_FORK: (3237:3239):(3236:3236) 0xad0 [0x18]: PERF_EVENT_FORK: (3237:3240):(3236:3236) 0xb18 [0x18]: PERF_EVENT_FORK: (3237:3241):(3236:3236) Shows us that the test (27d028d perf report: Update for the new FORK/EXIT events) in builtin-report.c: /* * A thread clone will have the same PID for both * parent and child. */ if (thread == parent) return 0; Will clearly fail. The problem is that perf_counter_fork() reports the actual parent, instead of the cloning thread. Fixing that (with the below patch), yields: # ./perf report -D | grep FORK 0x4c8 [0x18]: PERF_EVENT_FORK: (1590:1590):(1589:1589) 0xbd8 [0x18]: PERF_EVENT_FORK: (1590:1591):(1590:1590) 0xc80 [0x18]: PERF_EVENT_FORK: (1590:1592):(1590:1590) 0x3338 [0x18]: PERF_EVENT_FORK: (1590:1593):(1590:1590) 0x66b0 [0x18]: PERF_EVENT_FORK: (1590:1594):(1590:1590) Which both makes more sense and doesn't confuse perf report anymore. Reported-by: Pekka Enberg Signed-off-by: Peter Zijlstra Cc: Arnaldo Carvalho de Melo Cc: paulus@samba.org Cc: Anton Blanchard Cc: Arjan van de Ven LKML-Reference: <1250172882.5241.62.camel@twins> Signed-off-by: Ingo Molnar --- kernel/perf_counter.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index 3f841beefc7..534e20d14d6 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -3028,10 +3028,10 @@ static void perf_counter_task_output(struct perf_counter *counter, return; task_event->event.pid = perf_counter_pid(counter, task); - task_event->event.ppid = perf_counter_pid(counter, task->real_parent); + task_event->event.ppid = perf_counter_pid(counter, current); task_event->event.tid = perf_counter_tid(counter, task); - task_event->event.ptid = perf_counter_tid(counter, task->real_parent); + task_event->event.ptid = perf_counter_tid(counter, current); perf_output_put(&handle, task_event->event); perf_output_end(&handle); -- GitLab From e694958388c50148389b0e9b9e9e8945cf0f1b98 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Thu, 13 Aug 2009 08:28:36 -0700 Subject: [PATCH 1074/1342] Make sock_sendpage() use kernel_sendpage() kernel_sendpage() does the proper default case handling for when the socket doesn't have a native sendpage implementation. Now, arguably this might be something that we could instead solve by just specifying that all protocols should do it themselves at the protocol level, but we really only care about the common protocols. Does anybody really care about sendpage on something like Appletalk? Not likely. Acked-by: David S. Miller Acked-by: Julien TINNES Acked-by: Tavis Ormandy Cc: stable@kernel.org Signed-off-by: Linus Torvalds --- net/socket.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/socket.c b/net/socket.c index 791d71a36a9..6d471655904 100644 --- a/net/socket.c +++ b/net/socket.c @@ -736,7 +736,7 @@ static ssize_t sock_sendpage(struct file *file, struct page *page, if (more) flags |= MSG_MORE; - return sock->ops->sendpage(sock, page, offset, size, flags); + return kernel_sendpage(sock, page, offset, size, flags); } static ssize_t sock_splice_read(struct file *file, loff_t *ppos, -- GitLab From 416fbdff2137e8d8cc8f23f517bee3a26b11526f Mon Sep 17 00:00:00 2001 From: "Luis R. Rodriguez" Date: Tue, 11 Aug 2009 13:10:33 -0700 Subject: [PATCH 1075/1342] mac80211: fix panic when splicing unprepared TIDs We splice skbs from the pending queue for a TID onto the local pending queue when tearing down a block ack request. This is not necessary unless we actually have received a request to start a block ack request (rate control, for example). If we never received that request we should not be splicing the tid pending queue as it would be null, causing a panic. Not sure yet how exactly we allowed through a call when the tid state does not have at least HT_ADDBA_REQUESTED_MSK set, that will require some further review as it is not quite obvious. For more information see the bug report: http://bugzilla.kernel.org/show_bug.cgi?id=13922 This fixes this oops: BUG: unable to handle kernel NULL pointer dereference at 00000030 IP: [] ieee80211_agg_splice_packets+0x40/0xc0 [mac80211] *pdpt = 0000000002d1e001 *pde = 0000000000000000 Thread overran stack, or stack corrupted Oops: 0000 [#1] SMP last sysfs file: /sys/module/aes_generic/initstate Modules linked in: Pid: 0, comm: swapper Not tainted (2.6.31-rc5-wl #2) Dell DV051 EIP: 0060:[] EFLAGS: 00010292 CPU: 0 EIP is at ieee80211_agg_splice_packets+0x40/0xc0 [mac80211] EAX: 00000030 EBX: 0000004c ECX: 00000003 EDX: 00000000 ESI: c1c98000 EDI: f745a1c0 EBP: c076be58 ESP: c076be38 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 Process swapper (pid: 0, ti=c076a000 task=c0709160 task.ti=c076a000) Stack: Call Trace: [] ? ieee80211_stop_tx_ba_cb+0xab/0x150 [mac80211] [] ? ieee80211_tasklet_handler+0xce/0x110 [mac80211] [] ? net_rx_action+0xef/0x1d0 [] ? tasklet_action+0x58/0xc0 [] ? __do_softirq+0xc2/0x190 [] ? handle_IRQ_event+0x58/0x140 [] ? ack_apic_level+0x7e/0x270 [] ? do_softirq+0x3d/0x40 [] ? irq_exit+0x65/0x90 [] ? do_IRQ+0x4f/0xc0 [] ? irq_exit+0x7d/0x90 [] ? smp_apic_timer_interrupt+0x57/0x90 [] ? common_interrupt+0x29/0x30 [] ? mwait_idle+0xbe/0x100 [] ? cpu_idle+0x52/0x90 [] ? rest_init+0x55/0x60 [] ? start_kernel+0x315/0x37d [] ? unknown_bootoption+0x0/0x1f9 [] ? i386_start_kernel+0x79/0x81 Code: EIP: [] ieee80211_agg_splice_packets+0x40/0xc0 [mac80211] SS:ESP 0068:c076be38 CR2: 0000000000000030 Cc: stable@kernel.org Testedy-by: Jack Lau Signed-off-by: Luis R. Rodriguez Signed-off-by: John W. Linville --- net/mac80211/agg-tx.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/net/mac80211/agg-tx.c b/net/mac80211/agg-tx.c index 9e5762ad307..a24e59816b9 100644 --- a/net/mac80211/agg-tx.c +++ b/net/mac80211/agg-tx.c @@ -381,6 +381,14 @@ static void ieee80211_agg_splice_packets(struct ieee80211_local *local, &local->hw, queue, IEEE80211_QUEUE_STOP_REASON_AGGREGATION); + if (!(sta->ampdu_mlme.tid_state_tx[tid] & HT_ADDBA_REQUESTED_MSK)) + return; + + if (WARN(!sta->ampdu_mlme.tid_tx[tid], + "TID %d gone but expected when splicing aggregates from" + "the pending queue\n", tid)) + return; + if (!skb_queue_empty(&sta->ampdu_mlme.tid_tx[tid]->pending)) { spin_lock_irqsave(&local->queue_stop_reason_lock, flags); /* mark queue as pending, it is stopped already */ -- GitLab From 2d860ad76f4ee4d2eba0fe3797c8d7cdce432cc0 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Thu, 13 Aug 2009 13:05:10 -0700 Subject: [PATCH 1076/1342] genirq: prevent wakeup of freed irq thread free_irq() can remove an irqaction while the corresponding interrupt is in progress, but free_irq() sets action->thread to NULL unconditionally, which might lead to a NULL pointer dereference in handle_IRQ_event() when the hard interrupt context tries to wake up the handler thread. Prevent this by moving the thread stop after synchronize_irq(). No need to set action->thread to NULL either as action is going to be freed anyway. This fixes a boot crash reported against preempt-rt which uses the mainline irq threads code to implement full irq threading. [ tglx: removed local irqthread variable ] Signed-off-by: Linus Torvalds Signed-off-by: Thomas Gleixner --- kernel/irq/manage.c | 17 +++++++---------- 1 file changed, 7 insertions(+), 10 deletions(-) diff --git a/kernel/irq/manage.c b/kernel/irq/manage.c index 61c679db468..d222515a5a0 100644 --- a/kernel/irq/manage.c +++ b/kernel/irq/manage.c @@ -761,7 +761,6 @@ static struct irqaction *__free_irq(unsigned int irq, void *dev_id) { struct irq_desc *desc = irq_to_desc(irq); struct irqaction *action, **action_ptr; - struct task_struct *irqthread; unsigned long flags; WARN(in_interrupt(), "Trying to free IRQ %d from IRQ context!\n", irq); @@ -809,9 +808,6 @@ static struct irqaction *__free_irq(unsigned int irq, void *dev_id) desc->chip->disable(irq); } - irqthread = action->thread; - action->thread = NULL; - spin_unlock_irqrestore(&desc->lock, flags); unregister_handler_proc(irq, action); @@ -819,12 +815,6 @@ static struct irqaction *__free_irq(unsigned int irq, void *dev_id) /* Make sure it's not being used on another CPU: */ synchronize_irq(irq); - if (irqthread) { - if (!test_bit(IRQTF_DIED, &action->thread_flags)) - kthread_stop(irqthread); - put_task_struct(irqthread); - } - #ifdef CONFIG_DEBUG_SHIRQ /* * It's a shared IRQ -- the driver ought to be prepared for an IRQ @@ -840,6 +830,13 @@ static struct irqaction *__free_irq(unsigned int irq, void *dev_id) local_irq_restore(flags); } #endif + + if (action->thread) { + if (!test_bit(IRQTF_DIED, &action->thread_flags)) + kthread_stop(action->thread); + put_task_struct(action->thread); + } + return action; } -- GitLab From 15052c9e85bf0cdadcb69eb89623bf12bad8b4f8 Mon Sep 17 00:00:00 2001 From: "Kashyap, Desai" Date: Fri, 7 Aug 2009 19:33:17 +0530 Subject: [PATCH 1077/1342] [SCSI] mpt2sas: Introduced check for enclosure_handle to avoid crash Kernel panic is seen because of enclosure_handle received from FW is zero. Check is introduced before calling mpt2sas_config_get_enclosure_pg0. Signed-off-by: Kashyap Desai Signed-off-by: James Bottomley --- drivers/scsi/mpt2sas/mpt2sas_scsih.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) diff --git a/drivers/scsi/mpt2sas/mpt2sas_scsih.c b/drivers/scsi/mpt2sas/mpt2sas_scsih.c index 2a01a5f2a84..b1326bf78c9 100644 --- a/drivers/scsi/mpt2sas/mpt2sas_scsih.c +++ b/drivers/scsi/mpt2sas/mpt2sas_scsih.c @@ -3663,12 +3663,11 @@ _scsih_add_device(struct MPT2SAS_ADAPTER *ioc, u16 handle, u8 phy_num, u8 is_pd) sas_device->hidden_raid_component = is_pd; /* get enclosure_logical_id */ - if (!(mpt2sas_config_get_enclosure_pg0(ioc, &mpi_reply, &enclosure_pg0, - MPI2_SAS_ENCLOS_PGAD_FORM_HANDLE, - sas_device->enclosure_handle))) { + if (sas_device->enclosure_handle && !(mpt2sas_config_get_enclosure_pg0( + ioc, &mpi_reply, &enclosure_pg0, MPI2_SAS_ENCLOS_PGAD_FORM_HANDLE, + sas_device->enclosure_handle))) sas_device->enclosure_logical_id = le64_to_cpu(enclosure_pg0.EnclosureLogicalID); - } /* get device name */ sas_device->device_name = le64_to_cpu(sas_device_pg0.DeviceName); -- GitLab From 20f5895d55d9281830bfb7819c5c5b70b05297a6 Mon Sep 17 00:00:00 2001 From: "Kashyap, Desai" Date: Fri, 7 Aug 2009 19:34:26 +0530 Subject: [PATCH 1078/1342] [SCSI] mpt2sas: Expander fix oops saying "Already part of another port" Kernel panic is seen because driver did not tear down the port which should be dnoe using mpt2sas_transport_port_remove(). without this fix When expander is added back we would oops inside sas_port_add_phy. Signed-off-by: Kashyap Desai Signed-off-by: James Bottomley --- drivers/scsi/mpt2sas/mpt2sas_scsih.c | 21 +++++++++++++++------ 1 file changed, 15 insertions(+), 6 deletions(-) diff --git a/drivers/scsi/mpt2sas/mpt2sas_scsih.c b/drivers/scsi/mpt2sas/mpt2sas_scsih.c index b1326bf78c9..918445e1e65 100644 --- a/drivers/scsi/mpt2sas/mpt2sas_scsih.c +++ b/drivers/scsi/mpt2sas/mpt2sas_scsih.c @@ -3426,7 +3426,7 @@ _scsih_expander_add(struct MPT2SAS_ADAPTER *ioc, u16 handle) __le64 sas_address; int i; unsigned long flags; - struct _sas_port *mpt2sas_port; + struct _sas_port *mpt2sas_port = NULL; int rc = 0; if (!handle) @@ -3518,12 +3518,20 @@ _scsih_expander_add(struct MPT2SAS_ADAPTER *ioc, u16 handle) &expander_pg1, i, handle))) { printk(MPT2SAS_ERR_FMT "failure at %s:%d/%s()!\n", ioc->name, __FILE__, __LINE__, __func__); - continue; + rc = -1; + goto out_fail; } sas_expander->phy[i].handle = handle; sas_expander->phy[i].phy_id = i; - mpt2sas_transport_add_expander_phy(ioc, &sas_expander->phy[i], - expander_pg1, sas_expander->parent_dev); + + if ((mpt2sas_transport_add_expander_phy(ioc, + &sas_expander->phy[i], expander_pg1, + sas_expander->parent_dev))) { + printk(MPT2SAS_ERR_FMT "failure at %s:%d/%s()!\n", + ioc->name, __FILE__, __LINE__, __func__); + rc = -1; + goto out_fail; + } } if (sas_expander->enclosure_handle) { @@ -3540,8 +3548,9 @@ _scsih_expander_add(struct MPT2SAS_ADAPTER *ioc, u16 handle) out_fail: - if (sas_expander) - kfree(sas_expander->phy); + if (mpt2sas_port) + mpt2sas_transport_port_remove(ioc, sas_expander->sas_address, + sas_expander->parent_handle); kfree(sas_expander); return rc; } -- GitLab From 62727a7ba43c0abf2673e3877079c136a9721792 Mon Sep 17 00:00:00 2001 From: "Kashyap, Desai" Date: Fri, 7 Aug 2009 19:35:18 +0530 Subject: [PATCH 1079/1342] [SCSI] mpt2sas: Raid 10 Value is showing as Raid 1E in /va/log/messages When a volume is activated, the driver will recieve a pair of ir config change events to remove the foreign volume, then add the native. In the process of the removal event, the hidden raid componet is removed from the parent.When the disks is added back, the adding of the port fails becuase there is no instance of the device in its parent. To fix this issue, the driver needs to call mpt2sas_transport_update_links() prior to calling _scsih_add_device. In addition, we added sanity checks on volume add and removal to ignore events for foreign volumes. Signed-off-by: Kashyap Desai Signed-off-by: James Bottomley --- drivers/scsi/mpt2sas/mpt2sas_scsih.c | 90 ++++++++++++++++++++-------- 1 file changed, 64 insertions(+), 26 deletions(-) diff --git a/drivers/scsi/mpt2sas/mpt2sas_scsih.c b/drivers/scsi/mpt2sas/mpt2sas_scsih.c index 918445e1e65..22a95421e36 100644 --- a/drivers/scsi/mpt2sas/mpt2sas_scsih.c +++ b/drivers/scsi/mpt2sas/mpt2sas_scsih.c @@ -4258,12 +4258,6 @@ _scsih_sas_volume_add(struct MPT2SAS_ADAPTER *ioc, u16 handle = le16_to_cpu(element->VolDevHandle); int rc; -#if 0 /* RAID_HACKS */ - if (le32_to_cpu(event_data->Flags) & - MPI2_EVENT_IR_CHANGE_FLAGS_FOREIGN_CONFIG) - return; -#endif - mpt2sas_config_get_volume_wwid(ioc, handle, &wwid); if (!wwid) { printk(MPT2SAS_ERR_FMT @@ -4318,12 +4312,6 @@ _scsih_sas_volume_delete(struct MPT2SAS_ADAPTER *ioc, unsigned long flags; struct MPT2SAS_TARGET *sas_target_priv_data; -#if 0 /* RAID_HACKS */ - if (le32_to_cpu(event_data->Flags) & - MPI2_EVENT_IR_CHANGE_FLAGS_FOREIGN_CONFIG) - return; -#endif - spin_lock_irqsave(&ioc->raid_device_lock, flags); raid_device = _scsih_raid_device_find_by_handle(ioc, handle); spin_unlock_irqrestore(&ioc->raid_device_lock, flags); @@ -4436,14 +4424,38 @@ _scsih_sas_pd_add(struct MPT2SAS_ADAPTER *ioc, struct _sas_device *sas_device; unsigned long flags; u16 handle = le16_to_cpu(element->PhysDiskDevHandle); + Mpi2ConfigReply_t mpi_reply; + Mpi2SasDevicePage0_t sas_device_pg0; + u32 ioc_status; spin_lock_irqsave(&ioc->sas_device_lock, flags); sas_device = _scsih_sas_device_find_by_handle(ioc, handle); spin_unlock_irqrestore(&ioc->sas_device_lock, flags); - if (sas_device) + if (sas_device) { sas_device->hidden_raid_component = 1; - else - _scsih_add_device(ioc, handle, 0, 1); + return; + } + + if ((mpt2sas_config_get_sas_device_pg0(ioc, &mpi_reply, &sas_device_pg0, + MPI2_SAS_DEVICE_PGAD_FORM_HANDLE, handle))) { + printk(MPT2SAS_ERR_FMT "failure at %s:%d/%s()!\n", + ioc->name, __FILE__, __LINE__, __func__); + return; + } + + ioc_status = le16_to_cpu(mpi_reply.IOCStatus) & + MPI2_IOCSTATUS_MASK; + if (ioc_status != MPI2_IOCSTATUS_SUCCESS) { + printk(MPT2SAS_ERR_FMT "failure at %s:%d/%s()!\n", + ioc->name, __FILE__, __LINE__, __func__); + return; + } + + _scsih_link_change(ioc, + le16_to_cpu(sas_device_pg0.ParentDevHandle), + handle, sas_device_pg0.PhyNum, MPI2_SAS_NEG_LINK_RATE_1_5); + + _scsih_add_device(ioc, handle, 0, 1); } #ifdef CONFIG_SCSI_MPT2SAS_LOGGING @@ -4543,12 +4555,15 @@ _scsih_sas_ir_config_change_event(struct MPT2SAS_ADAPTER *ioc, u8 VF_ID, { Mpi2EventIrConfigElement_t *element; int i; + u8 foreign_config; #ifdef CONFIG_SCSI_MPT2SAS_LOGGING if (ioc->logging_level & MPT_DEBUG_EVENT_WORK_TASK) _scsih_sas_ir_config_change_event_debug(ioc, event_data); #endif + foreign_config = (le32_to_cpu(event_data->Flags) & + MPI2_EVENT_IR_CHANGE_FLAGS_FOREIGN_CONFIG) ? 1 : 0; element = (Mpi2EventIrConfigElement_t *)&event_data->ConfigElement[0]; for (i = 0; i < event_data->NumElements; i++, element++) { @@ -4556,11 +4571,13 @@ _scsih_sas_ir_config_change_event(struct MPT2SAS_ADAPTER *ioc, u8 VF_ID, switch (element->ReasonCode) { case MPI2_EVENT_IR_CHANGE_RC_VOLUME_CREATED: case MPI2_EVENT_IR_CHANGE_RC_ADDED: - _scsih_sas_volume_add(ioc, element); + if (!foreign_config) + _scsih_sas_volume_add(ioc, element); break; case MPI2_EVENT_IR_CHANGE_RC_VOLUME_DELETED: case MPI2_EVENT_IR_CHANGE_RC_REMOVED: - _scsih_sas_volume_delete(ioc, element); + if (!foreign_config) + _scsih_sas_volume_delete(ioc, element); break; case MPI2_EVENT_IR_CHANGE_RC_PD_CREATED: _scsih_sas_pd_hide(ioc, element); @@ -4679,6 +4696,9 @@ _scsih_sas_ir_physical_disk_event(struct MPT2SAS_ADAPTER *ioc, u8 VF_ID, u32 state; struct _sas_device *sas_device; unsigned long flags; + Mpi2ConfigReply_t mpi_reply; + Mpi2SasDevicePage0_t sas_device_pg0; + u32 ioc_status; if (event_data->ReasonCode != MPI2_EVENT_IR_PHYSDISK_RC_STATE_CHANGED) return; @@ -4695,22 +4715,40 @@ _scsih_sas_ir_physical_disk_event(struct MPT2SAS_ADAPTER *ioc, u8 VF_ID, spin_unlock_irqrestore(&ioc->sas_device_lock, flags); switch (state) { -#if 0 - case MPI2_RAID_PD_STATE_OFFLINE: - if (sas_device) - _scsih_remove_device(ioc, handle); - break; -#endif case MPI2_RAID_PD_STATE_ONLINE: case MPI2_RAID_PD_STATE_DEGRADED: case MPI2_RAID_PD_STATE_REBUILDING: case MPI2_RAID_PD_STATE_OPTIMAL: - if (sas_device) + if (sas_device) { sas_device->hidden_raid_component = 1; - else - _scsih_add_device(ioc, handle, 0, 1); + return; + } + + if ((mpt2sas_config_get_sas_device_pg0(ioc, &mpi_reply, + &sas_device_pg0, MPI2_SAS_DEVICE_PGAD_FORM_HANDLE, + handle))) { + printk(MPT2SAS_ERR_FMT "failure at %s:%d/%s()!\n", + ioc->name, __FILE__, __LINE__, __func__); + return; + } + + ioc_status = le16_to_cpu(mpi_reply.IOCStatus) & + MPI2_IOCSTATUS_MASK; + if (ioc_status != MPI2_IOCSTATUS_SUCCESS) { + printk(MPT2SAS_ERR_FMT "failure at %s:%d/%s()!\n", + ioc->name, __FILE__, __LINE__, __func__); + return; + } + + _scsih_link_change(ioc, + le16_to_cpu(sas_device_pg0.ParentDevHandle), + handle, sas_device_pg0.PhyNum, MPI2_SAS_NEG_LINK_RATE_1_5); + + _scsih_add_device(ioc, handle, 0, 1); + break; + case MPI2_RAID_PD_STATE_OFFLINE: case MPI2_RAID_PD_STATE_NOT_CONFIGURED: case MPI2_RAID_PD_STATE_NOT_COMPATIBLE: case MPI2_RAID_PD_STATE_HOT_SPARE: -- GitLab From be9e8cd75ce8d94ae4aab721fdcc337fa78a9090 Mon Sep 17 00:00:00 2001 From: "Kashyap, Desai" Date: Fri, 7 Aug 2009 19:36:43 +0530 Subject: [PATCH 1080/1342] [SCSI] mpt2sas: Excessive log info causes sas iounit page time out Inhibit 0x3117 loginfos - during cable pull, there are too many printks going to the syslog, this is have impact on how fast the interrupt routine can handle keeping up with command completions; this was the root cause to the config pages timeouts. Signed-off-by: Kashyap Desai Signed-off-by: James Bottomley --- drivers/scsi/mpt2sas/mpt2sas_base.c | 4 ++++ drivers/scsi/mpt2sas/mpt2sas_scsih.c | 4 ++++ 2 files changed, 8 insertions(+) diff --git a/drivers/scsi/mpt2sas/mpt2sas_base.c b/drivers/scsi/mpt2sas/mpt2sas_base.c index f3da592f7bc..ed9965e4b96 100644 --- a/drivers/scsi/mpt2sas/mpt2sas_base.c +++ b/drivers/scsi/mpt2sas/mpt2sas_base.c @@ -440,6 +440,10 @@ _base_sas_log_info(struct MPT2SAS_ADAPTER *ioc , u32 log_info) if (sas_loginfo.dw.bus_type != 3 /*SAS*/) return; + /* each nexus loss loginfo */ + if (log_info == 0x31170000) + return; + /* eat the loginfos associated with task aborts */ if (ioc->ignore_loginfos && (log_info == 30050000 || log_info == 0x31140000 || log_info == 0x31130000)) diff --git a/drivers/scsi/mpt2sas/mpt2sas_scsih.c b/drivers/scsi/mpt2sas/mpt2sas_scsih.c index 22a95421e36..25c8d8294af 100644 --- a/drivers/scsi/mpt2sas/mpt2sas_scsih.c +++ b/drivers/scsi/mpt2sas/mpt2sas_scsih.c @@ -2767,6 +2767,10 @@ _scsih_scsi_ioc_info(struct MPT2SAS_ADAPTER *ioc, struct scsi_cmnd *scmd, char *desc_ioc_state = NULL; char *desc_scsi_status = NULL; char *desc_scsi_state = ioc->tmp_string; + u32 log_info = le32_to_cpu(mpi_reply->IOCLogInfo); + + if (log_info == 0x31170000) + return; switch (ioc_status) { case MPI2_IOCSTATUS_SUCCESS: -- GitLab From 6bd4e1e4d6023f4da069fd68729c502cc4e6dfd0 Mon Sep 17 00:00:00 2001 From: "Kashyap, Desai" Date: Fri, 7 Aug 2009 19:37:14 +0530 Subject: [PATCH 1081/1342] [SCSI] mpt2sas: fix infinite loop inside config request This restriction is introduced just to avoid loop of config_request. Retry must be limited so we have restricted config request to maximum 2 times. Signed-off-by: Kashyap Desai Signed-off-by: James Bottomley --- drivers/scsi/mpt2sas/mpt2sas_config.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/scsi/mpt2sas/mpt2sas_config.c b/drivers/scsi/mpt2sas/mpt2sas_config.c index 58cfb97846f..1c6658c6023 100644 --- a/drivers/scsi/mpt2sas/mpt2sas_config.c +++ b/drivers/scsi/mpt2sas/mpt2sas_config.c @@ -247,6 +247,12 @@ _config_request(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigRequest_t retry_count = 0; retry_config: + if (retry_count) { + if (retry_count > 2) /* attempt only 2 retries */ + return -EFAULT; + printk(MPT2SAS_INFO_FMT "%s: attempting retry (%d)\n", + ioc->name, __func__, retry_count); + } wait_state_count = 0; ioc_state = mpt2sas_base_get_iocstate(ioc, 1); while (ioc_state != MPI2_IOC_STATE_OPERATIONAL) { -- GitLab From e4750c989f732555fca86dd73d488c79972362db Mon Sep 17 00:00:00 2001 From: "Kashyap, Desai" Date: Fri, 7 Aug 2009 19:37:59 +0530 Subject: [PATCH 1082/1342] [SCSI] mpt2sas: fix crash due to Watchdog is active while OS in standby mode Fix oops ocurring at hibernation time. This oops was due to the firmware fault watchdog timer still running after we freed resources. To fix the issue we need to terminate the watchdog timer at hibernation time. Signed-off-by: Kashyap Desai Signed-off-by: James Bottomley --- drivers/scsi/mpt2sas/mpt2sas_base.c | 88 +++++++++++++++++++--------- drivers/scsi/mpt2sas/mpt2sas_base.h | 2 + drivers/scsi/mpt2sas/mpt2sas_scsih.c | 2 + 3 files changed, 64 insertions(+), 28 deletions(-) diff --git a/drivers/scsi/mpt2sas/mpt2sas_base.c b/drivers/scsi/mpt2sas/mpt2sas_base.c index ed9965e4b96..c29c4f9851b 100644 --- a/drivers/scsi/mpt2sas/mpt2sas_base.c +++ b/drivers/scsi/mpt2sas/mpt2sas_base.c @@ -119,6 +119,64 @@ _base_fault_reset_work(struct work_struct *work) spin_unlock_irqrestore(&ioc->ioc_reset_in_progress_lock, flags); } +/** + * mpt2sas_base_start_watchdog - start the fault_reset_work_q + * @ioc: pointer to scsi command object + * Context: sleep. + * + * Return nothing. + */ +void +mpt2sas_base_start_watchdog(struct MPT2SAS_ADAPTER *ioc) +{ + unsigned long flags; + + if (ioc->fault_reset_work_q) + return; + + /* initialize fault polling */ + INIT_DELAYED_WORK(&ioc->fault_reset_work, _base_fault_reset_work); + snprintf(ioc->fault_reset_work_q_name, + sizeof(ioc->fault_reset_work_q_name), "poll_%d_status", ioc->id); + ioc->fault_reset_work_q = + create_singlethread_workqueue(ioc->fault_reset_work_q_name); + if (!ioc->fault_reset_work_q) { + printk(MPT2SAS_ERR_FMT "%s: failed (line=%d)\n", + ioc->name, __func__, __LINE__); + return; + } + spin_lock_irqsave(&ioc->ioc_reset_in_progress_lock, flags); + if (ioc->fault_reset_work_q) + queue_delayed_work(ioc->fault_reset_work_q, + &ioc->fault_reset_work, + msecs_to_jiffies(FAULT_POLLING_INTERVAL)); + spin_unlock_irqrestore(&ioc->ioc_reset_in_progress_lock, flags); +} + +/** + * mpt2sas_base_stop_watchdog - stop the fault_reset_work_q + * @ioc: pointer to scsi command object + * Context: sleep. + * + * Return nothing. + */ +void +mpt2sas_base_stop_watchdog(struct MPT2SAS_ADAPTER *ioc) +{ + unsigned long flags; + struct workqueue_struct *wq; + + spin_lock_irqsave(&ioc->ioc_reset_in_progress_lock, flags); + wq = ioc->fault_reset_work_q; + ioc->fault_reset_work_q = NULL; + spin_unlock_irqrestore(&ioc->ioc_reset_in_progress_lock, flags); + if (wq) { + if (!cancel_delayed_work(&ioc->fault_reset_work)) + flush_workqueue(wq); + destroy_workqueue(wq); + } +} + #ifdef CONFIG_SCSI_MPT2SAS_LOGGING /** * _base_sas_ioc_info - verbose translation of the ioc status @@ -3209,7 +3267,6 @@ int mpt2sas_base_attach(struct MPT2SAS_ADAPTER *ioc) { int r, i; - unsigned long flags; dinitprintk(ioc, printk(MPT2SAS_DEBUG_FMT "%s\n", ioc->name, __func__)); @@ -3292,23 +3349,7 @@ mpt2sas_base_attach(struct MPT2SAS_ADAPTER *ioc) if (r) goto out_free_resources; - /* initialize fault polling */ - INIT_DELAYED_WORK(&ioc->fault_reset_work, _base_fault_reset_work); - snprintf(ioc->fault_reset_work_q_name, - sizeof(ioc->fault_reset_work_q_name), "poll_%d_status", ioc->id); - ioc->fault_reset_work_q = - create_singlethread_workqueue(ioc->fault_reset_work_q_name); - if (!ioc->fault_reset_work_q) { - printk(MPT2SAS_ERR_FMT "%s: failed (line=%d)\n", - ioc->name, __func__, __LINE__); - goto out_free_resources; - } - spin_lock_irqsave(&ioc->ioc_reset_in_progress_lock, flags); - if (ioc->fault_reset_work_q) - queue_delayed_work(ioc->fault_reset_work_q, - &ioc->fault_reset_work, - msecs_to_jiffies(FAULT_POLLING_INTERVAL)); - spin_unlock_irqrestore(&ioc->ioc_reset_in_progress_lock, flags); + mpt2sas_base_start_watchdog(ioc); return 0; out_free_resources: @@ -3341,20 +3382,11 @@ mpt2sas_base_attach(struct MPT2SAS_ADAPTER *ioc) void mpt2sas_base_detach(struct MPT2SAS_ADAPTER *ioc) { - unsigned long flags; - struct workqueue_struct *wq; dexitprintk(ioc, printk(MPT2SAS_DEBUG_FMT "%s\n", ioc->name, __func__)); - spin_lock_irqsave(&ioc->ioc_reset_in_progress_lock, flags); - wq = ioc->fault_reset_work_q; - ioc->fault_reset_work_q = NULL; - spin_unlock_irqrestore(&ioc->ioc_reset_in_progress_lock, flags); - if (!cancel_delayed_work(&ioc->fault_reset_work)) - flush_workqueue(wq); - destroy_workqueue(wq); - + mpt2sas_base_stop_watchdog(ioc); mpt2sas_base_free_resources(ioc); _base_release_memory_pools(ioc); kfree(ioc->pfacts); diff --git a/drivers/scsi/mpt2sas/mpt2sas_base.h b/drivers/scsi/mpt2sas/mpt2sas_base.h index 286c185fa9e..a29935726e7 100644 --- a/drivers/scsi/mpt2sas/mpt2sas_base.h +++ b/drivers/scsi/mpt2sas/mpt2sas_base.h @@ -673,6 +673,8 @@ typedef void (*MPT_CALLBACK)(struct MPT2SAS_ADAPTER *ioc, u16 smid, u8 VF_ID, /* base shared API */ extern struct list_head mpt2sas_ioc_list; +void mpt2sas_base_start_watchdog(struct MPT2SAS_ADAPTER *ioc); +void mpt2sas_base_stop_watchdog(struct MPT2SAS_ADAPTER *ioc); int mpt2sas_base_attach(struct MPT2SAS_ADAPTER *ioc); void mpt2sas_base_detach(struct MPT2SAS_ADAPTER *ioc); diff --git a/drivers/scsi/mpt2sas/mpt2sas_scsih.c b/drivers/scsi/mpt2sas/mpt2sas_scsih.c index 25c8d8294af..2e9a4445596 100644 --- a/drivers/scsi/mpt2sas/mpt2sas_scsih.c +++ b/drivers/scsi/mpt2sas/mpt2sas_scsih.c @@ -5824,6 +5824,7 @@ _scsih_suspend(struct pci_dev *pdev, pm_message_t state) struct MPT2SAS_ADAPTER *ioc = shost_priv(shost); u32 device_state; + mpt2sas_base_stop_watchdog(ioc); flush_scheduled_work(); scsi_block_requests(shost); device_state = pci_choose_state(pdev, state); @@ -5866,6 +5867,7 @@ _scsih_resume(struct pci_dev *pdev) mpt2sas_base_hard_reset_handler(ioc, CAN_SLEEP, SOFT_RESET); scsi_unblock_requests(shost); + mpt2sas_base_start_watchdog(ioc); return 0; } #endif /* CONFIG_PM */ -- GitLab From fcfe6392d18283df3c561b5ef59c330d485ff8ca Mon Sep 17 00:00:00 2001 From: "Kashyap, Desai" Date: Fri, 7 Aug 2009 19:38:48 +0530 Subject: [PATCH 1083/1342] [SCSI] mpt2sas: fix oops because drv data points to NULL on resume from hibernate Fix another ocurring when the system resumes. This oops was due to driver setting the pci drvdata to NULL on the prior hibernation. Becuase it was set to NULL, upon resmume we assume the pci drvdata is non-zero, and we oops. To fix the ooops, we don't set pci drvdata to NULL at hibernation time. Signed-off-by: Kashyap Desai Signed-off-by: James Bottomley --- drivers/scsi/mpt2sas/mpt2sas_base.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/scsi/mpt2sas/mpt2sas_base.c b/drivers/scsi/mpt2sas/mpt2sas_base.c index c29c4f9851b..35a13867495 100644 --- a/drivers/scsi/mpt2sas/mpt2sas_base.c +++ b/drivers/scsi/mpt2sas/mpt2sas_base.c @@ -1171,7 +1171,6 @@ mpt2sas_base_map_resources(struct MPT2SAS_ADAPTER *ioc) } } - pci_set_drvdata(pdev, ioc->shost); _base_mask_interrupts(ioc); r = _base_enable_msix(ioc); if (r) @@ -1194,7 +1193,6 @@ mpt2sas_base_map_resources(struct MPT2SAS_ADAPTER *ioc) ioc->pci_irq = -1; pci_release_selected_regions(ioc->pdev, ioc->bars); pci_disable_device(pdev); - pci_set_drvdata(pdev, NULL); return r; } @@ -3253,7 +3251,6 @@ mpt2sas_base_free_resources(struct MPT2SAS_ADAPTER *ioc) ioc->chip_phys = 0; pci_release_selected_regions(ioc->pdev, ioc->bars); pci_disable_device(pdev); - pci_set_drvdata(pdev, NULL); return; } @@ -3275,6 +3272,7 @@ mpt2sas_base_attach(struct MPT2SAS_ADAPTER *ioc) if (r) return r; + pci_set_drvdata(ioc->pdev, ioc->shost); r = _base_make_ioc_ready(ioc, CAN_SLEEP, SOFT_RESET); if (r) goto out_free_resources; @@ -3357,6 +3355,7 @@ mpt2sas_base_attach(struct MPT2SAS_ADAPTER *ioc) ioc->remove_host = 1; mpt2sas_base_free_resources(ioc); _base_release_memory_pools(ioc); + pci_set_drvdata(ioc->pdev, NULL); kfree(ioc->tm_cmds.reply); kfree(ioc->transport_cmds.reply); kfree(ioc->config_cmds.reply); @@ -3389,6 +3388,7 @@ mpt2sas_base_detach(struct MPT2SAS_ADAPTER *ioc) mpt2sas_base_stop_watchdog(ioc); mpt2sas_base_free_resources(ioc); _base_release_memory_pools(ioc); + pci_set_drvdata(ioc->pdev, NULL); kfree(ioc->pfacts); kfree(ioc->ctl_cmds.reply); kfree(ioc->base_cmds.reply); -- GitLab From f9b14c9183b250cf128c7d2341e6b9bdbbcd8f35 Mon Sep 17 00:00:00 2001 From: "Kashyap, Desai" Date: Fri, 7 Aug 2009 19:39:59 +0530 Subject: [PATCH 1084/1342] [SCSI] mpt2sas: Bump driver version 01.100.04.00 Bump version to 01.100.04.00 Signed-off-by: Kashyap Desai Signed-off-by: James Bottomley --- drivers/scsi/mpt2sas/mpt2sas_base.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/scsi/mpt2sas/mpt2sas_base.h b/drivers/scsi/mpt2sas/mpt2sas_base.h index a29935726e7..acdcff150a3 100644 --- a/drivers/scsi/mpt2sas/mpt2sas_base.h +++ b/drivers/scsi/mpt2sas/mpt2sas_base.h @@ -69,10 +69,10 @@ #define MPT2SAS_DRIVER_NAME "mpt2sas" #define MPT2SAS_AUTHOR "LSI Corporation " #define MPT2SAS_DESCRIPTION "LSI MPT Fusion SAS 2.0 Device Driver" -#define MPT2SAS_DRIVER_VERSION "01.100.03.00" +#define MPT2SAS_DRIVER_VERSION "01.100.04.00" #define MPT2SAS_MAJOR_VERSION 01 #define MPT2SAS_MINOR_VERSION 100 -#define MPT2SAS_BUILD_VERSION 03 +#define MPT2SAS_BUILD_VERSION 04 #define MPT2SAS_RELEASE_VERSION 00 /* -- GitLab From 64f1607ffbbc772685733ea63e6f7f4183df1b16 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Thu, 13 Aug 2009 15:43:34 -0700 Subject: [PATCH 1085/1342] Linux 2.6.31-rc6 --- Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Makefile b/Makefile index 0d46615bffe..abcfa85f8f8 100644 --- a/Makefile +++ b/Makefile @@ -1,7 +1,7 @@ VERSION = 2 PATCHLEVEL = 6 SUBLEVEL = 31 -EXTRAVERSION = -rc5 +EXTRAVERSION = -rc6 NAME = Man-Eating Seals of Antiquity # *DOCUMENTATION* -- GitLab From 993e6f2fd487e2acddd711f79cf48f3420731382 Mon Sep 17 00:00:00 2001 From: Oliver Hartkopp Date: Tue, 11 Aug 2009 02:41:24 +0000 Subject: [PATCH 1086/1342] can: fix oops caused by wrong rtnl newlink usage For 'real' hardware CAN devices the netlink interface is used to set CAN specific communication parameters. Real CAN hardware can not be created with the ip tool ... The invocation of 'ip link add type can' lead to an oops as the standard rtnl newlink function was called: http://bugzilla.kernel.org/show_bug.cgi?id=13954 This patch adds a private newlink function for the CAN device driver interface that unconditionally returns -EOPNOTSUPP. Signed-off-by: Oliver Hartkopp Reported-by: Dmitry Eremin-Solenikov CC: Patrick McHardy CC: Wolfgang Grandegger Signed-off-by: David S. Miller --- drivers/net/can/dev.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/net/can/dev.c b/drivers/net/can/dev.c index 9e4283aff82..e1a4f821423 100644 --- a/drivers/net/can/dev.c +++ b/drivers/net/can/dev.c @@ -611,11 +611,18 @@ nla_put_failure: return -EMSGSIZE; } +static int can_newlink(struct net_device *dev, + struct nlattr *tb[], struct nlattr *data[]) +{ + return -EOPNOTSUPP; +} + static struct rtnl_link_ops can_link_ops __read_mostly = { .kind = "can", .maxtype = IFLA_CAN_MAX, .policy = can_policy, .setup = can_setup, + .newlink = can_newlink, .changelink = can_changelink, .fill_info = can_fill_info, .fill_xstats = can_fill_xstats, -- GitLab From 237057ad3fe5644fa471be474a160de2fc2e5870 Mon Sep 17 00:00:00 2001 From: Don Skidmore Date: Tue, 11 Aug 2009 13:18:14 +0000 Subject: [PATCH 1087/1342] ixgbe: fix issues setting rx-usecs with legacy interrupts Currently setting rx-usecs when the interface is in legacy interrupt mode it is not immediate. We were only setting EITR for each MSIx vector and since this count would be zero for legacy mode it wasn't set until after a reset. This patch corrects that by checking what mode we are in and then setting EITR accordingly. Signed-off-by: Don Skidmore Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_ethtool.c | 27 +++++++++++++++++++-------- 1 file changed, 19 insertions(+), 8 deletions(-) diff --git a/drivers/net/ixgbe/ixgbe_ethtool.c b/drivers/net/ixgbe/ixgbe_ethtool.c index 79144e950a3..dff8dfac7ed 100644 --- a/drivers/net/ixgbe/ixgbe_ethtool.c +++ b/drivers/net/ixgbe/ixgbe_ethtool.c @@ -1948,6 +1948,7 @@ static int ixgbe_set_coalesce(struct net_device *netdev, struct ethtool_coalesce *ec) { struct ixgbe_adapter *adapter = netdev_priv(netdev); + struct ixgbe_q_vector *q_vector; int i; if (ec->tx_max_coalesced_frames_irq) @@ -1982,14 +1983,24 @@ static int ixgbe_set_coalesce(struct net_device *netdev, adapter->itr_setting = 0; } - for (i = 0; i < adapter->num_msix_vectors - NON_Q_VECTORS; i++) { - struct ixgbe_q_vector *q_vector = adapter->q_vector[i]; - if (q_vector->txr_count && !q_vector->rxr_count) - /* tx vector gets half the rate */ - q_vector->eitr = (adapter->eitr_param >> 1); - else - /* rx only or mixed */ - q_vector->eitr = adapter->eitr_param; + /* MSI/MSIx Interrupt Mode */ + if (adapter->flags & + (IXGBE_FLAG_MSIX_ENABLED | IXGBE_FLAG_MSI_ENABLED)) { + int num_vectors = adapter->num_msix_vectors - NON_Q_VECTORS; + for (i = 0; i < num_vectors; i++) { + q_vector = adapter->q_vector[i]; + if (q_vector->txr_count && !q_vector->rxr_count) + /* tx vector gets half the rate */ + q_vector->eitr = (adapter->eitr_param >> 1); + else + /* rx only or mixed */ + q_vector->eitr = adapter->eitr_param; + ixgbe_write_eitr(q_vector); + } + /* Legacy Interrupt Mode */ + } else { + q_vector = adapter->q_vector[0]; + q_vector->eitr = adapter->eitr_param; ixgbe_write_eitr(q_vector); } -- GitLab From e424fa9d6a0add1a9b812b07e3607daaa5b9e53d Mon Sep 17 00:00:00 2001 From: Amit Kumar Salecha Date: Thu, 13 Aug 2009 07:03:00 +0000 Subject: [PATCH 1088/1342] netxen: remove netxen workqueue o Remove private workqueue in the driver, move all scheduled tasks to keventd workqueues. This makes ports (interfaces) of same / different NIC boards independent, in terms of their link watchdog and reset tasks. o Move quick checks for link status and temperature in timer callback, schedule watchdog task only if link status changed or temperature reached critical threshold. This also fixes deadlock when thermal panic occurs, watchdog work was flushing workqueue that it was sitting on. Signed-off-by: Amit Kumar Salecha Signed-off-by: Dhananjay Phadke Signed-off-by: David S. Miller --- drivers/net/netxen/netxen_nic.h | 2 +- drivers/net/netxen/netxen_nic_main.c | 69 +++++++++++++++++----------- 2 files changed, 42 insertions(+), 29 deletions(-) diff --git a/drivers/net/netxen/netxen_nic.h b/drivers/net/netxen/netxen_nic.h index f86e05047d1..a9c1fcca5e7 100644 --- a/drivers/net/netxen/netxen_nic.h +++ b/drivers/net/netxen/netxen_nic.h @@ -1254,7 +1254,7 @@ struct netxen_adapter { u8 mc_enabled; u8 max_mc_count; u8 rss_supported; - u8 resv2; + u8 link_changed; u32 resv3; u8 has_link_events; diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index 70c05c4c0ca..d24e1cb93a2 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -94,10 +94,6 @@ static struct pci_device_id netxen_pci_tbl[] __devinitdata = { MODULE_DEVICE_TABLE(pci, netxen_pci_tbl); -static struct workqueue_struct *netxen_workq; -#define SCHEDULE_WORK(tp) queue_work(netxen_workq, tp) -#define FLUSH_SCHEDULED_WORK() flush_workqueue(netxen_workq) - static void netxen_watchdog(unsigned long); static uint32_t crb_cmd_producer[4] = { @@ -880,7 +876,6 @@ netxen_nic_down(struct netxen_adapter *adapter, struct net_device *netdev) spin_unlock(&adapter->tx_clean_lock); del_timer_sync(&adapter->watchdog_timer); - FLUSH_SCHEDULED_WORK(); } @@ -1177,6 +1172,9 @@ static void __devexit netxen_nic_remove(struct pci_dev *pdev) unregister_netdev(netdev); + cancel_work_sync(&adapter->watchdog_task); + cancel_work_sync(&adapter->tx_timeout_task); + if (adapter->is_up == NETXEN_ADAPTER_UP_MAGIC) { netxen_nic_detach(adapter); } @@ -1211,6 +1209,9 @@ netxen_nic_suspend(struct pci_dev *pdev, pm_message_t state) if (netif_running(netdev)) netxen_nic_down(adapter, netdev); + cancel_work_sync(&adapter->watchdog_task); + cancel_work_sync(&adapter->tx_timeout_task); + if (adapter->is_up == NETXEN_ADAPTER_UP_MAGIC) netxen_nic_detach(adapter); @@ -1549,11 +1550,6 @@ static int netxen_nic_check_temp(struct netxen_adapter *adapter) "%s: Device temperature %d degrees C exceeds" " maximum allowed. Hardware has been shut down.\n", netdev->name, temp_val); - - netif_device_detach(netdev); - netxen_nic_down(adapter, netdev); - netxen_nic_detach(adapter); - rv = 1; } else if (temp_state == NX_TEMP_WARN) { if (adapter->temp == NX_TEMP_NORMAL) { @@ -1587,10 +1583,7 @@ void netxen_advert_link_change(struct netxen_adapter *adapter, int linkup) netif_carrier_off(netdev); netif_stop_queue(netdev); } - - if (!adapter->has_link_events) - netxen_nic_set_link_parameters(adapter); - + adapter->link_changed = !adapter->has_link_events; } else if (!adapter->ahw.linkup && linkup) { printk(KERN_INFO "%s: %s NIC Link is up\n", netxen_nic_driver_name, netdev->name); @@ -1599,9 +1592,7 @@ void netxen_advert_link_change(struct netxen_adapter *adapter, int linkup) netif_carrier_on(netdev); netif_wake_queue(netdev); } - - if (!adapter->has_link_events) - netxen_nic_set_link_parameters(adapter); + adapter->link_changed = !adapter->has_link_events; } } @@ -1628,11 +1619,36 @@ static void netxen_nic_handle_phy_intr(struct netxen_adapter *adapter) netxen_advert_link_change(adapter, linkup); } +static void netxen_nic_thermal_shutdown(struct netxen_adapter *adapter) +{ + struct net_device *netdev = adapter->netdev; + + netif_device_detach(netdev); + netxen_nic_down(adapter, netdev); + netxen_nic_detach(adapter); +} + static void netxen_watchdog(unsigned long v) { struct netxen_adapter *adapter = (struct netxen_adapter *)v; - SCHEDULE_WORK(&adapter->watchdog_task); + if (netxen_nic_check_temp(adapter)) + goto do_sched; + + if (!adapter->has_link_events) { + netxen_nic_handle_phy_intr(adapter); + + if (adapter->link_changed) + goto do_sched; + } + + if (netif_running(adapter->netdev)) + mod_timer(&adapter->watchdog_timer, jiffies + 2 * HZ); + + return; + +do_sched: + schedule_work(&adapter->watchdog_task); } void netxen_watchdog_task(struct work_struct *work) @@ -1640,11 +1656,13 @@ void netxen_watchdog_task(struct work_struct *work) struct netxen_adapter *adapter = container_of(work, struct netxen_adapter, watchdog_task); - if (netxen_nic_check_temp(adapter)) + if (adapter->temp == NX_TEMP_PANIC) { + netxen_nic_thermal_shutdown(adapter); return; + } - if (!adapter->has_link_events) - netxen_nic_handle_phy_intr(adapter); + if (adapter->link_changed) + netxen_nic_set_link_parameters(adapter); if (netif_running(adapter->netdev)) mod_timer(&adapter->watchdog_timer, jiffies + 2 * HZ); @@ -1652,9 +1670,8 @@ void netxen_watchdog_task(struct work_struct *work) static void netxen_tx_timeout(struct net_device *netdev) { - struct netxen_adapter *adapter = (struct netxen_adapter *) - netdev_priv(netdev); - SCHEDULE_WORK(&adapter->tx_timeout_task); + struct netxen_adapter *adapter = netdev_priv(netdev); + schedule_work(&adapter->tx_timeout_task); } static void netxen_tx_timeout_task(struct work_struct *work) @@ -1811,9 +1828,6 @@ static int __init netxen_init_module(void) { printk(KERN_INFO "%s\n", netxen_nic_driver_string); - if ((netxen_workq = create_singlethread_workqueue("netxen")) == NULL) - return -ENOMEM; - return pci_register_driver(&netxen_driver); } @@ -1822,7 +1836,6 @@ module_init(netxen_init_module); static void __exit netxen_exit_module(void) { pci_unregister_driver(&netxen_driver); - destroy_workqueue(netxen_workq); } module_exit(netxen_exit_module); -- GitLab From 232e7d68d50c9ac3a55d716e5ae215ecd1e043b9 Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Thu, 13 Aug 2009 07:03:01 +0000 Subject: [PATCH 1089/1342] netxen: free napi resources during detach o Defer napi resouce allocation to device attach. o Free napi resources and delete napi during detach. This ensures right behavior across firmware reset. Signed-off-by: Dhananjay Phadke Signed-off-by: David S. Miller --- drivers/net/netxen/netxen_nic_init.c | 7 ------ drivers/net/netxen/netxen_nic_main.c | 32 +++++++++++++++++++++------- 2 files changed, 24 insertions(+), 15 deletions(-) diff --git a/drivers/net/netxen/netxen_nic_init.c b/drivers/net/netxen/netxen_nic_init.c index 7acf204e38c..5d3343ef3d8 100644 --- a/drivers/net/netxen/netxen_nic_init.c +++ b/drivers/net/netxen/netxen_nic_init.c @@ -184,13 +184,6 @@ void netxen_free_sw_resources(struct netxen_adapter *adapter) kfree(recv_ctx->rds_rings); skip_rds: - if (recv_ctx->sds_rings == NULL) - goto skip_sds; - - for(ring = 0; ring < adapter->max_sds_rings; ring++) - recv_ctx->sds_rings[ring].consumer = 0; - -skip_sds: if (adapter->tx_ring == NULL) return; diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index d24e1cb93a2..28f270f5ac7 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -167,6 +167,8 @@ netxen_free_sds_rings(struct netxen_recv_context *recv_ctx) { if (recv_ctx->sds_rings != NULL) kfree(recv_ctx->sds_rings); + + recv_ctx->sds_rings = NULL; } static int @@ -188,6 +190,21 @@ netxen_napi_add(struct netxen_adapter *adapter, struct net_device *netdev) return 0; } +static void +netxen_napi_del(struct netxen_adapter *adapter) +{ + int ring; + struct nx_host_sds_ring *sds_ring; + struct netxen_recv_context *recv_ctx = &adapter->recv_ctx; + + for (ring = 0; ring < adapter->max_sds_rings; ring++) { + sds_ring = &recv_ctx->sds_rings[ring]; + netif_napi_del(&sds_ring->napi); + } + + netxen_free_sds_rings(&adapter->recv_ctx); +} + static void netxen_napi_enable(struct netxen_adapter *adapter) { @@ -889,10 +906,12 @@ netxen_nic_attach(struct netxen_adapter *adapter) struct nx_host_tx_ring *tx_ring; err = netxen_init_firmware(adapter); - if (err != 0) { - printk(KERN_ERR "Failed to init firmware\n"); - return -EIO; - } + if (err) + return err; + + err = netxen_napi_add(adapter, netdev); + if (err) + return err; if (adapter->fw_major < 4) adapter->max_rds_rings = 3; @@ -956,6 +975,7 @@ netxen_nic_detach(struct netxen_adapter *adapter) netxen_free_hw_resources(adapter); netxen_release_rx_buffers(adapter); netxen_nic_free_irq(adapter); + netxen_napi_del(adapter); netxen_free_sw_resources(adapter); adapter->is_up = 0; @@ -1100,9 +1120,6 @@ netxen_nic_probe(struct pci_dev *pdev, const struct pci_device_id *ent) netdev->irq = adapter->msix_entries[0].vector; - if (netxen_napi_add(adapter, netdev)) - goto err_out_disable_msi; - init_timer(&adapter->watchdog_timer); adapter->watchdog_timer.function = &netxen_watchdog; adapter->watchdog_timer.data = (unsigned long)adapter; @@ -1183,7 +1200,6 @@ static void __devexit netxen_nic_remove(struct pci_dev *pdev) netxen_free_adapter_offload(adapter); netxen_teardown_intr(adapter); - netxen_free_sds_rings(&adapter->recv_ctx); netxen_cleanup_pci_map(adapter); -- GitLab From 5b766182a110311fbf618f736bc8a8f2f7ce3f4c Mon Sep 17 00:00:00 2001 From: Antonio Ospite Date: Wed, 22 Jul 2009 17:20:50 -0300 Subject: [PATCH 1090/1342] V4L/DVB (12330): pxa_camera: Fix Oops in pxa_camera_probe mclk_get_divisor uses pcdev->soc_host.dev, make sure it is initialized. Signed-off-by: Antonio Ospite Signed-off-by: Guennadi Liakhovetski Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/pxa_camera.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/media/video/pxa_camera.c b/drivers/media/video/pxa_camera.c index 46e0d8ad880..e048d25798c 100644 --- a/drivers/media/video/pxa_camera.c +++ b/drivers/media/video/pxa_camera.c @@ -1579,6 +1579,7 @@ static int __devinit pxa_camera_probe(struct platform_device *pdev) pcdev->mclk = 20000000; } + pcdev->soc_host.dev = &pdev->dev; pcdev->mclk_divisor = mclk_get_divisor(pcdev); INIT_LIST_HEAD(&pcdev->capture); @@ -1644,7 +1645,6 @@ static int __devinit pxa_camera_probe(struct platform_device *pdev) pcdev->soc_host.drv_name = PXA_CAM_DRV_NAME; pcdev->soc_host.ops = &pxa_soc_camera_host_ops; pcdev->soc_host.priv = pcdev; - pcdev->soc_host.dev = &pdev->dev; pcdev->soc_host.nr = pdev->id; err = soc_camera_host_register(&pcdev->soc_host); -- GitLab From ed18d0c87ee0ab6e0985d83c19cd135b1bd54998 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Thu, 23 Jul 2009 21:46:57 -0300 Subject: [PATCH 1091/1342] V4L/DVB (12337): ivtv: Read buffer overflow This mistakenly tests against sizeof(freqs) instead of the array size. Due to the mask the only illegal value possible was 3. Signed-off-by: Roel Kluin Signed-off-by: Andy Walls Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/ivtv/ivtv-controls.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/media/video/ivtv/ivtv-controls.c b/drivers/media/video/ivtv/ivtv-controls.c index a3b77ed3f08..4a9c8ce0ecb 100644 --- a/drivers/media/video/ivtv/ivtv-controls.c +++ b/drivers/media/video/ivtv/ivtv-controls.c @@ -17,6 +17,7 @@ along with this program; if not, write to the Free Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ +#include #include "ivtv-driver.h" #include "ivtv-cards.h" @@ -281,7 +282,7 @@ int ivtv_s_ext_ctrls(struct file *file, void *fh, struct v4l2_ext_controls *c) idx = p.audio_properties & 0x03; /* The audio clock of the digitizer must match the codec sample rate otherwise you get some very strange effects. */ - if (idx < sizeof(freqs)) + if (idx < ARRAY_SIZE(freqs)) ivtv_call_all(itv, audio, s_clock_freq, freqs[idx]); return err; } -- GitLab From 225aeb1c5863bc92c6bb1f921e9a6cf4d15dbb2a Mon Sep 17 00:00:00 2001 From: Andy Walls Date: Thu, 23 Jul 2009 21:51:29 -0300 Subject: [PATCH 1092/1342] V4L/DVB (12338): cx18: Read buffer overflow This mistakenly tested against sizeof(freqs) instead of the array size. Due to the mask the only illegal value possible was 3. Reported-by: Roel Kluin Signed-off-by: Andy Walls Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/cx18/cx18-controls.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/media/video/cx18/cx18-controls.c b/drivers/media/video/cx18/cx18-controls.c index 5136df19833..93f0dae0135 100644 --- a/drivers/media/video/cx18/cx18-controls.c +++ b/drivers/media/video/cx18/cx18-controls.c @@ -20,6 +20,7 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA * 02111-1307 USA */ +#include #include "cx18-driver.h" #include "cx18-cards.h" @@ -317,7 +318,7 @@ int cx18_s_ext_ctrls(struct file *file, void *fh, struct v4l2_ext_controls *c) idx = p.audio_properties & 0x03; /* The audio clock of the digitizer must match the codec sample rate otherwise you get some very strange effects. */ - if (idx < sizeof(freqs)) + if (idx < ARRAY_SIZE(freqs)) cx18_call_all(cx, audio, s_clock_freq, freqs[idx]); return err; } -- GitLab From 296544e15a7126373851abd40acc526b79b91432 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Mon, 27 Jul 2009 08:24:29 -0300 Subject: [PATCH 1093/1342] V4L/DVB (12340): mtv9v011: Add a missing chip version to the driver Some mt9v011 webcams report 0x8332 chip version, instead of 0x8243. From the revision history at the mt9v011 datasheet, it seems that the chip version has changed from the first release of the chip. Thanks-to hermann pitton for pointing this to me, on his tests with a Silvercrest webcam. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 3 ++- drivers/media/video/mt9v011.c | 14 +++++++++----- drivers/media/video/mt9v011.h | 3 ++- 3 files changed, 13 insertions(+), 7 deletions(-) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 320f1f60276..bc213a1f9c1 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -1771,7 +1771,8 @@ static int em28xx_hint_sensor(struct em28xx *dev) version = be16_to_cpu(version_be); switch (version) { - case 0x8243: /* mt9v011 640x480 1.3 Mpix sensor */ + case 0x8232: /* mt9v011 640x480 1.3 Mpix sensor */ + case 0x8243: /* mt9v011 rev B 640x480 1.3 Mpix sensor */ dev->model = EM2820_BOARD_SILVERCREST_WEBCAM; sensor_name = "mt9v011"; dev->em28xx_sensor = EM28XX_MT9V011; diff --git a/drivers/media/video/mt9v011.c b/drivers/media/video/mt9v011.c index b2260de645f..c14bf47d692 100644 --- a/drivers/media/video/mt9v011.c +++ b/drivers/media/video/mt9v011.c @@ -393,10 +393,13 @@ static int mt9v011_s_register(struct v4l2_subdev *sd, static int mt9v011_g_chip_ident(struct v4l2_subdev *sd, struct v4l2_dbg_chip_ident *chip) { + u16 version; struct i2c_client *client = v4l2_get_subdevdata(sd); + version = mt9v011_read(sd, R00_MT9V011_CHIP_VERSION); + return v4l2_chip_ident_i2c_client(client, chip, V4L2_IDENT_MT9V011, - MT9V011_VERSION); + version); } static const struct v4l2_subdev_core_ops mt9v011_core_ops = { @@ -449,8 +452,9 @@ static int mt9v011_probe(struct i2c_client *c, /* Check if the sensor is really a MT9V011 */ version = mt9v011_read(sd, R00_MT9V011_CHIP_VERSION); - if (version != MT9V011_VERSION) { - v4l2_info(sd, "*** unknown micron chip detected (0x%04x.\n", + if ((version != MT9V011_VERSION) && + (version != MT9V011_REV_B_VERSION)) { + v4l2_info(sd, "*** unknown micron chip detected (0x%04x).\n", version); kfree(core); return -EINVAL; @@ -461,8 +465,8 @@ static int mt9v011_probe(struct i2c_client *c, core->height = 480; core->xtal = 27000000; /* Hz */ - v4l_info(c, "chip found @ 0x%02x (%s)\n", - c->addr << 1, c->adapter->name); + v4l_info(c, "chip found @ 0x%02x (%s - chip version 0x%04x)\n", + c->addr << 1, c->adapter->name, version); return 0; } diff --git a/drivers/media/video/mt9v011.h b/drivers/media/video/mt9v011.h index 9e443ee3055..3350fd6083c 100644 --- a/drivers/media/video/mt9v011.h +++ b/drivers/media/video/mt9v011.h @@ -30,6 +30,7 @@ #define R35_MT9V011_GLOBAL_GAIN 0x35 #define RF1_MT9V011_CHIP_ENABLE 0xf1 -#define MT9V011_VERSION 0x8243 +#define MT9V011_VERSION 0x8232 +#define MT9V011_REV_B_VERSION 0x8243 #endif -- GitLab From 458f9aa391efd34867f8cabac2e2f1af00cbc562 Mon Sep 17 00:00:00 2001 From: Jan Nikitenko Date: Thu, 18 Jun 2009 08:11:57 -0300 Subject: [PATCH 1094/1342] V4L/DVB (12341): zl10353 and qt1010: fix stack corruption bug Fixes stack corruption bug present in dump_regs function of zl10353 and qt1010 drivers: the buffer buf was one byte smaller than required - there are 4 chars for address prefix, 16 * 3 chars for dump of 16 eeprom bytes per line and 1 byte for zero ending the string required, i.e. 53 bytes, but only 52 were provided. The one byte missing in stack based buffer buf can cause stack corruption possibly leading to kernel oops, as discovered originally with af9015 driver (af9015: fix stack corruption bug). Signed-off-by: Jan Nikitenko Signed-off-by: Mauro Carvalho Chehab --- drivers/media/common/tuners/qt1010.c | 12 +++++------- drivers/media/dvb/frontends/zl10353.c | 12 +++++------- 2 files changed, 10 insertions(+), 14 deletions(-) diff --git a/drivers/media/common/tuners/qt1010.c b/drivers/media/common/tuners/qt1010.c index 825aa1412e6..9f5dba244cb 100644 --- a/drivers/media/common/tuners/qt1010.c +++ b/drivers/media/common/tuners/qt1010.c @@ -64,24 +64,22 @@ static int qt1010_writereg(struct qt1010_priv *priv, u8 reg, u8 val) /* dump all registers */ static void qt1010_dump_regs(struct qt1010_priv *priv) { - char buf[52], buf2[4]; u8 reg, val; for (reg = 0; ; reg++) { if (reg % 16 == 0) { if (reg) - printk("%s\n", buf); - sprintf(buf, "%02x: ", reg); + printk(KERN_CONT "\n"); + printk(KERN_DEBUG "%02x:", reg); } if (qt1010_readreg(priv, reg, &val) == 0) - sprintf(buf2, "%02x ", val); + printk(KERN_CONT " %02x", val); else - strcpy(buf2, "-- "); - strcat(buf, buf2); + printk(KERN_CONT " --"); if (reg == 0x2f) break; } - printk("%s\n", buf); + printk(KERN_CONT "\n"); } static int qt1010_set_params(struct dvb_frontend *fe, diff --git a/drivers/media/dvb/frontends/zl10353.c b/drivers/media/dvb/frontends/zl10353.c index 148b6f7f6cb..66f5c1fb307 100644 --- a/drivers/media/dvb/frontends/zl10353.c +++ b/drivers/media/dvb/frontends/zl10353.c @@ -98,7 +98,6 @@ static int zl10353_read_register(struct zl10353_state *state, u8 reg) static void zl10353_dump_regs(struct dvb_frontend *fe) { struct zl10353_state *state = fe->demodulator_priv; - char buf[52], buf2[4]; int ret; u8 reg; @@ -106,19 +105,18 @@ static void zl10353_dump_regs(struct dvb_frontend *fe) for (reg = 0; ; reg++) { if (reg % 16 == 0) { if (reg) - printk(KERN_DEBUG "%s\n", buf); - sprintf(buf, "%02x: ", reg); + printk(KERN_CONT "\n"); + printk(KERN_DEBUG "%02x:", reg); } ret = zl10353_read_register(state, reg); if (ret >= 0) - sprintf(buf2, "%02x ", (u8)ret); + printk(KERN_CONT " %02x", (u8)ret); else - strcpy(buf2, "-- "); - strcat(buf, buf2); + printk(KERN_CONT " --"); if (reg == 0xff) break; } - printk(KERN_DEBUG "%s\n", buf); + printk(KERN_CONT "\n"); } static void zl10353_calc_nominal_rate(struct dvb_frontend *fe, -- GitLab From 0a6e44d1beb30813f62ad376a31694e637858328 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Wed, 29 Jul 2009 01:39:12 -0300 Subject: [PATCH 1095/1342] V4L/DVB (12344): em28xx: fix support for Plextor ConvertX PX-TV100U This device uses msp34xx and uses 2.048 MHz frequency for I2S communication. Thanks to Angelo Cano for pointing the issues with this device and proposing an approach for fixing the issue. Tested-by: Angelo Cano Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index bc213a1f9c1..d0b033bce86 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -622,22 +622,27 @@ struct em28xx_board em28xx_boards[] = { }, [EM2861_BOARD_PLEXTOR_PX_TV100U] = { .name = "Plextor ConvertX PX-TV100U", - .valid = EM28XX_BOARD_NOT_VALIDATED, .tuner_type = TUNER_TNF_5335MF, + .xclk = EM28XX_XCLK_I2S_MSB_TIMING | + EM28XX_XCLK_FREQUENCY_12MHZ, .tda9887_conf = TDA9887_PRESENT, .decoder = EM28XX_TVP5150, + .has_msp34xx = 1, .input = { { .type = EM28XX_VMUX_TELEVISION, .vmux = TVP5150_COMPOSITE0, .amux = EM28XX_AMUX_LINE_IN, + .gpio = pinnacle_hybrid_pro_analog, }, { .type = EM28XX_VMUX_COMPOSITE1, .vmux = TVP5150_COMPOSITE1, .amux = EM28XX_AMUX_LINE_IN, + .gpio = pinnacle_hybrid_pro_analog, }, { .type = EM28XX_VMUX_SVIDEO, .vmux = TVP5150_SVIDEO, .amux = EM28XX_AMUX_LINE_IN, + .gpio = pinnacle_hybrid_pro_analog, } }, }, @@ -1877,9 +1882,8 @@ void em28xx_pre_card_setup(struct em28xx *dev) /* request some modules */ switch (dev->model) { case EM2861_BOARD_PLEXTOR_PX_TV100U: - /* FIXME guess */ - /* Turn on analog audio output */ - em28xx_write_reg(dev, EM28XX_R08_GPIO, 0xfd); + /* Sets the msp34xx I2S speed */ + dev->i2s_speed = 2048000; break; case EM2861_BOARD_KWORLD_PVRTV_300U: case EM2880_BOARD_KWORLD_DVB_305U: -- GitLab From 337ab6d34f0be7cfbfb5ac8cb651276fc58aa20d Mon Sep 17 00:00:00 2001 From: Sohail Syyed Date: Sun, 26 Jul 2009 11:06:20 -0300 Subject: [PATCH 1096/1342] V4L/DVB (12349): cx88: HVR1300 ensure switching from Encoder to DVB-T and back is reliable Current tip is broken and does not switch back to DVB-T correctly Signed-off-by: Sohail Syyed Signed-off-by: Steven Toth Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/cx88/cx88-mpeg.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/media/video/cx88/cx88-mpeg.c b/drivers/media/video/cx88/cx88-mpeg.c index da4e3912cd3..7172dcf2a4f 100644 --- a/drivers/media/video/cx88/cx88-mpeg.c +++ b/drivers/media/video/cx88/cx88-mpeg.c @@ -116,6 +116,10 @@ static int cx8802_start_dma(struct cx8802_dev *dev, udelay(100); break; case CX88_BOARD_HAUPPAUGE_HVR1300: + /* Enable MPEG parallel IO and video signal pins */ + cx_write(MO_PINMUX_IO, 0x88); + cx_write(TS_SOP_STAT, 0); + cx_write(TS_VALERR_CNTRL, 0); break; case CX88_BOARD_PINNACLE_PCTV_HD_800i: /* Enable MPEG parallel IO and video signal pins */ -- GitLab From 6655be0f4f377d7e249219c6031c4be3533604a2 Mon Sep 17 00:00:00 2001 From: Michael Krufky Date: Mon, 20 Jul 2009 12:20:58 -0300 Subject: [PATCH 1097/1342] V4L/DVB (12362): cx23885-417: fix manipulation of tvnorms Currently, the VIDIOC_S_STD ioctl just returns -EINVAL regardless of the norm passed. This patch sets cx23885_mpeg_template.tvnorms and cx23885_mpeg_template.current_norm so that the VIDIOC_S_STD will work. Thanks to Joseph Yasi for pointing this out, even though this particular fix was already pushed into a development repository, merge priority of this changeset has been escalated as a result of Joseph posting this identical patch. Signed-off-by: Michael Krufky Signed-off-by: Joseph A. Yasi Reviewed-by: Steven Toth Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/cx23885/cx23885-417.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/media/video/cx23885/cx23885-417.c b/drivers/media/video/cx23885/cx23885-417.c index e0cf21e0b1b..1a1048b18f7 100644 --- a/drivers/media/video/cx23885/cx23885-417.c +++ b/drivers/media/video/cx23885/cx23885-417.c @@ -1715,6 +1715,8 @@ static struct video_device cx23885_mpeg_template = { .fops = &mpeg_fops, .ioctl_ops = &mpeg_ioctl_ops, .minor = -1, + .tvnorms = CX23885_NORMS, + .current_norm = V4L2_STD_NTSC_M, }; void cx23885_417_unregister(struct cx23885_dev *dev) -- GitLab From ba1bc64272f0af668690ba2bf859b13172db7230 Mon Sep 17 00:00:00 2001 From: Nils Kassube Date: Tue, 28 Jul 2009 11:54:52 -0300 Subject: [PATCH 1098/1342] V4L/DVB (12371): af9015: Fix for crash in dvb-usb-af9015 Moving BOOT fixes problem. Signed-off-by: Nils Kassube Acked-by: Antti Palosaari Signed-off-by: Douglas Schilling Landgraf Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb/dvb-usb/af9015.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/media/dvb/dvb-usb/af9015.c b/drivers/media/dvb/dvb-usb/af9015.c index 4cb31e7c13c..26690dfb326 100644 --- a/drivers/media/dvb/dvb-usb/af9015.c +++ b/drivers/media/dvb/dvb-usb/af9015.c @@ -81,7 +81,6 @@ static int af9015_rw_udev(struct usb_device *udev, struct req_t *req) switch (req->cmd) { case GET_CONFIG: - case BOOT: case READ_MEMORY: case RECONNECT_USB: case GET_IR_CODE: @@ -100,6 +99,7 @@ static int af9015_rw_udev(struct usb_device *udev, struct req_t *req) case WRITE_VIRTUAL_MEMORY: case COPY_FIRMWARE: case DOWNLOAD_FIRMWARE: + case BOOT: break; default: err("unknown command:%d", req->cmd); -- GitLab From 261982f17051d10a1054a77ec8ae13517e0acee2 Mon Sep 17 00:00:00 2001 From: Brian Johnson Date: Sun, 19 Jul 2009 15:58:56 -0300 Subject: [PATCH 1099/1342] V4L/DVB (12373a): Add gspca sn9c20x subdriver entry to MAINTAINERS file MAINTAINERS | 8 ++++++++ Signed-off-by: Brian Johnson Acked-by: Jean-Francois Moine Signed-off-by: Mauro Carvalho Chehab --- MAINTAINERS | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index b1114cfac6b..2c4326c0de9 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2238,6 +2238,14 @@ T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git S: Maintained F: drivers/media/video/gspca/pac207.c +GSPCA SN9C20X SUBDRIVER +P: Brian Johnson +M: brijohn@gmail.com +L: linux-media@vger.kernel.org +T: git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git +S: Maintained +F: drivers/media/video/gspca/sn9c20x.c + GSPCA T613 SUBDRIVER M: Leandro Costantino L: linux-media@vger.kernel.org -- GitLab From d1ae4e1d05cc982b6b480c1a3d69b8bb231e3493 Mon Sep 17 00:00:00 2001 From: Michael Krufky Date: Sun, 12 Jul 2009 18:25:45 -0300 Subject: [PATCH 1100/1342] V4L/DVB (12374): sms1xxx: fix broken Hauppauge devices The current GPIO configuration breaks all Hauppauge devices. The code being removed affects Hauppauge devices only, and is the cause of the breakage. Signed-off-by: Michael Krufky Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb/siano/sms-cards.c | 100 ---------------------------- 1 file changed, 100 deletions(-) diff --git a/drivers/media/dvb/siano/sms-cards.c b/drivers/media/dvb/siano/sms-cards.c index d8b15d583bd..76bd3cb82d9 100644 --- a/drivers/media/dvb/siano/sms-cards.c +++ b/drivers/media/dvb/siano/sms-cards.c @@ -124,91 +124,15 @@ int sms_board_event(struct smscore_device_t *coredev, switch (gevent) { case BOARD_EVENT_POWER_INIT: /* including hotplug */ - switch (board_id) { - case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM: - /* set I/O and turn off all LEDs */ - smscore_gpio_configure(coredev, - board->board_cfg.leds_power, - &MyGpioConfig); - smscore_gpio_set_level(coredev, - board->board_cfg.leds_power, 0); - smscore_gpio_configure(coredev, board->board_cfg.led0, - &MyGpioConfig); - smscore_gpio_set_level(coredev, - board->board_cfg.led0, 0); - smscore_gpio_configure(coredev, board->board_cfg.led1, - &MyGpioConfig); - smscore_gpio_set_level(coredev, - board->board_cfg.led1, 0); - break; - case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD_R2: - case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD: - /* set I/O and turn off LNA */ - smscore_gpio_configure(coredev, - board->board_cfg.foreign_lna0_ctrl, - &MyGpioConfig); - smscore_gpio_set_level(coredev, - board->board_cfg.foreign_lna0_ctrl, - 0); - break; - } break; /* BOARD_EVENT_BIND */ case BOARD_EVENT_POWER_SUSPEND: - switch (board_id) { - case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM: - smscore_gpio_set_level(coredev, - board->board_cfg.leds_power, 0); - smscore_gpio_set_level(coredev, - board->board_cfg.led0, 0); - smscore_gpio_set_level(coredev, - board->board_cfg.led1, 0); - break; - case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD_R2: - case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD: - smscore_gpio_set_level(coredev, - board->board_cfg.foreign_lna0_ctrl, - 0); - break; - } break; /* BOARD_EVENT_POWER_SUSPEND */ case BOARD_EVENT_POWER_RESUME: - switch (board_id) { - case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM: - smscore_gpio_set_level(coredev, - board->board_cfg.leds_power, 1); - smscore_gpio_set_level(coredev, - board->board_cfg.led0, 1); - smscore_gpio_set_level(coredev, - board->board_cfg.led1, 0); - break; - case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD_R2: - case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD: - smscore_gpio_set_level(coredev, - board->board_cfg.foreign_lna0_ctrl, - 1); - break; - } break; /* BOARD_EVENT_POWER_RESUME */ case BOARD_EVENT_BIND: - switch (board_id) { - case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM: - smscore_gpio_set_level(coredev, - board->board_cfg.leds_power, 1); - smscore_gpio_set_level(coredev, - board->board_cfg.led0, 1); - smscore_gpio_set_level(coredev, - board->board_cfg.led1, 0); - break; - case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD_R2: - case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD: - smscore_gpio_set_level(coredev, - board->board_cfg.foreign_lna0_ctrl, - 1); - break; - } break; /* BOARD_EVENT_BIND */ case BOARD_EVENT_SCAN_PROG: @@ -218,20 +142,8 @@ int sms_board_event(struct smscore_device_t *coredev, case BOARD_EVENT_EMERGENCY_WARNING_SIGNAL: break; /* BOARD_EVENT_EMERGENCY_WARNING_SIGNAL */ case BOARD_EVENT_FE_LOCK: - switch (board_id) { - case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM: - smscore_gpio_set_level(coredev, - board->board_cfg.led1, 1); - break; - } break; /* BOARD_EVENT_FE_LOCK */ case BOARD_EVENT_FE_UNLOCK: - switch (board_id) { - case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM: - smscore_gpio_set_level(coredev, - board->board_cfg.led1, 0); - break; - } break; /* BOARD_EVENT_FE_UNLOCK */ case BOARD_EVENT_DEMOD_LOCK: break; /* BOARD_EVENT_DEMOD_LOCK */ @@ -248,20 +160,8 @@ int sms_board_event(struct smscore_device_t *coredev, case BOARD_EVENT_RECEPTION_LOST_0: break; /* BOARD_EVENT_RECEPTION_LOST_0 */ case BOARD_EVENT_MULTIPLEX_OK: - switch (board_id) { - case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM: - smscore_gpio_set_level(coredev, - board->board_cfg.led1, 1); - break; - } break; /* BOARD_EVENT_MULTIPLEX_OK */ case BOARD_EVENT_MULTIPLEX_ERRORS: - switch (board_id) { - case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM: - smscore_gpio_set_level(coredev, - board->board_cfg.led1, 0); - break; - } break; /* BOARD_EVENT_MULTIPLEX_ERRORS */ default: -- GitLab From d79cd8393ae85ebaf53a8fc93491eea96522d68e Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Sun, 19 Jul 2009 19:16:05 -0300 Subject: [PATCH 1101/1342] V4L/DVB (12328): uvcvideo: Don't apply the FIX_BANDWIDTH quirk to all ViMicro devices Commit 50144aeeb702ea105697ae5249f059ea3990b838 broke the Samsung NC10 netbook webcam. Instead of applying the FIX_BANDWIDTH quirk to all ViMicro devices, list the devices explicitly. Signed-off-by: Laurent Pinchart Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/uvc/uvc_driver.c | 24 +++++++++++++++++++++--- 1 file changed, 21 insertions(+), 3 deletions(-) diff --git a/drivers/media/video/uvc/uvc_driver.c b/drivers/media/video/uvc/uvc_driver.c index 89927b7aec2..04b47832fa0 100644 --- a/drivers/media/video/uvc/uvc_driver.c +++ b/drivers/media/video/uvc/uvc_driver.c @@ -1845,11 +1845,29 @@ static struct usb_device_id uvc_ids[] = { .bInterfaceSubClass = 1, .bInterfaceProtocol = 0, .driver_info = UVC_QUIRK_STREAM_NO_FID }, - /* ViMicro */ - { .match_flags = USB_DEVICE_ID_MATCH_VENDOR + /* ViMicro Vega */ + { .match_flags = USB_DEVICE_ID_MATCH_DEVICE + | USB_DEVICE_ID_MATCH_INT_INFO, + .idVendor = 0x0ac8, + .idProduct = 0x332d, + .bInterfaceClass = USB_CLASS_VIDEO, + .bInterfaceSubClass = 1, + .bInterfaceProtocol = 0, + .driver_info = UVC_QUIRK_FIX_BANDWIDTH }, + /* ViMicro - Minoru3D */ + { .match_flags = USB_DEVICE_ID_MATCH_DEVICE + | USB_DEVICE_ID_MATCH_INT_INFO, + .idVendor = 0x0ac8, + .idProduct = 0x3410, + .bInterfaceClass = USB_CLASS_VIDEO, + .bInterfaceSubClass = 1, + .bInterfaceProtocol = 0, + .driver_info = UVC_QUIRK_FIX_BANDWIDTH }, + /* ViMicro Venus - Minoru3D */ + { .match_flags = USB_DEVICE_ID_MATCH_DEVICE | USB_DEVICE_ID_MATCH_INT_INFO, .idVendor = 0x0ac8, - .idProduct = 0x0000, + .idProduct = 0x3420, .bInterfaceClass = USB_CLASS_VIDEO, .bInterfaceSubClass = 1, .bInterfaceProtocol = 0, -- GitLab From bd0232c13419b7ce51e02942082ff6af231e0f84 Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Sat, 1 Aug 2009 18:14:24 -0300 Subject: [PATCH 1102/1342] V4L/DVB (12380): uvcvideo: Avoid flooding the kernel log with "unknown event type" messages The iSight sends non-UVC status events through the interrupt endpoint. Those invalid events are reported to the kernel log, resulting in a log flood. Only log the events when the UVC_TRACE_STATUS flag is set. Signed-off-by: Laurent Pinchart Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/uvc/uvc_status.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/media/video/uvc/uvc_status.c b/drivers/media/video/uvc/uvc_status.c index f152a990386..1ca6dff7361 100644 --- a/drivers/media/video/uvc/uvc_status.c +++ b/drivers/media/video/uvc/uvc_status.c @@ -145,8 +145,8 @@ static void uvc_status_complete(struct urb *urb) break; default: - uvc_printk(KERN_INFO, "unknown event type %u.\n", - dev->status[0]); + uvc_trace(UVC_TRACE_STATUS, "Unknown status event " + "type %u.\n", dev->status[0]); break; } } -- GitLab From 79a6382551507ce196c3b4296e32b5386cdfbf15 Mon Sep 17 00:00:00 2001 From: Michael Krufky Date: Sun, 2 Aug 2009 12:37:34 -0300 Subject: [PATCH 1103/1342] V4L/DVB (12386): sms1xxx: fix build warning: unused variable 'board' Remove the following build warning: sms-cards.c: In function 'sms_board_event': sms-cards.c:120: warning: unused variable 'board' Thanks to Hans Verkuil for pointing this out. The problem code has been #if 0'd for now, this will likely be used again in the future, once the event interface is complete. Cc: Hans Verkuil Signed-off-by: Michael Krufky Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb/siano/sms-cards.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/drivers/media/dvb/siano/sms-cards.c b/drivers/media/dvb/siano/sms-cards.c index 76bd3cb82d9..0420e2885e7 100644 --- a/drivers/media/dvb/siano/sms-cards.c +++ b/drivers/media/dvb/siano/sms-cards.c @@ -116,8 +116,6 @@ static inline void sms_gpio_assign_11xx_default_led_config( int sms_board_event(struct smscore_device_t *coredev, enum SMS_BOARD_EVENTS gevent) { - int board_id = smscore_get_board_id(coredev); - struct sms_board *board = sms_get_board(board_id); struct smscore_gpio_config MyGpioConfig; sms_gpio_assign_11xx_default_led_config(&MyGpioConfig); -- GitLab From b5f05064b556da5183adc383e5f8d50af0392849 Mon Sep 17 00:00:00 2001 From: Michael Krufky Date: Mon, 3 Aug 2009 16:51:33 -0300 Subject: [PATCH 1104/1342] V4L/DVB (12390): saa7134: Use correct product name for Hauppauge WinTV-HVR1150 ATSC/QAM-Hybrid Signed-off-by: Michael Krufky Signed-off-by: Mauro Carvalho Chehab --- Documentation/video4linux/CARDLIST.saa7134 | 2 +- drivers/media/video/saa7134/saa7134-cards.c | 20 ++++++++++---------- drivers/media/video/saa7134/saa7134-dvb.c | 2 +- drivers/media/video/saa7134/saa7134.h | 2 +- 4 files changed, 13 insertions(+), 13 deletions(-) diff --git a/Documentation/video4linux/CARDLIST.saa7134 b/Documentation/video4linux/CARDLIST.saa7134 index 15562427e8a..a82b767f9e7 100644 --- a/Documentation/video4linux/CARDLIST.saa7134 +++ b/Documentation/video4linux/CARDLIST.saa7134 @@ -153,7 +153,7 @@ 152 -> Asus Tiger Rev:1.00 [1043:4857] 153 -> Kworld Plus TV Analog Lite PCI [17de:7128] 154 -> Avermedia AVerTV GO 007 FM Plus [1461:f31d] -155 -> Hauppauge WinTV-HVR1120 ATSC/QAM-Hybrid [0070:6706,0070:6708] +155 -> Hauppauge WinTV-HVR1150 ATSC/QAM-Hybrid [0070:6706,0070:6708] 156 -> Hauppauge WinTV-HVR1110r3 DVB-T/Hybrid [0070:6707,0070:6709,0070:670a] 157 -> Avermedia AVerTV Studio 507UA [1461:a11b] 158 -> AVerMedia Cardbus TV/Radio (E501R) [1461:b7e9] diff --git a/drivers/media/video/saa7134/saa7134-cards.c b/drivers/media/video/saa7134/saa7134-cards.c index 06861b782b9..60e74ad5967 100644 --- a/drivers/media/video/saa7134/saa7134-cards.c +++ b/drivers/media/video/saa7134/saa7134-cards.c @@ -3331,8 +3331,8 @@ struct saa7134_board saa7134_boards[] = { .gpio = 0x0200100, }, }, - [SAA7134_BOARD_HAUPPAUGE_HVR1120] = { - .name = "Hauppauge WinTV-HVR1120 ATSC/QAM-Hybrid", + [SAA7134_BOARD_HAUPPAUGE_HVR1150] = { + .name = "Hauppauge WinTV-HVR1150 ATSC/QAM-Hybrid", .audio_clock = 0x00187de7, .tuner_type = TUNER_PHILIPS_TDA8290, .radio_type = UNSET, @@ -5862,7 +5862,7 @@ struct pci_device_id saa7134_pci_tbl[] = { .device = PCI_DEVICE_ID_PHILIPS_SAA7133, .subvendor = 0x0070, .subdevice = 0x6706, - .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1120, + .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1150, },{ .vendor = PCI_VENDOR_ID_PHILIPS, .device = PCI_DEVICE_ID_PHILIPS_SAA7133, @@ -5874,7 +5874,7 @@ struct pci_device_id saa7134_pci_tbl[] = { .device = PCI_DEVICE_ID_PHILIPS_SAA7133, .subvendor = 0x0070, .subdevice = 0x6708, - .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1120, + .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1150, },{ .vendor = PCI_VENDOR_ID_PHILIPS, .device = PCI_DEVICE_ID_PHILIPS_SAA7133, @@ -6363,7 +6363,7 @@ static int saa7134_tda8290_18271_callback(struct saa7134_dev *dev, switch (command) { case TDA18271_CALLBACK_CMD_AGC_ENABLE: /* 0 */ switch (dev->board) { - case SAA7134_BOARD_HAUPPAUGE_HVR1120: + case SAA7134_BOARD_HAUPPAUGE_HVR1150: case SAA7134_BOARD_HAUPPAUGE_HVR1110R3: ret = saa7134_tda18271_hvr11x0_toggle_agc(dev, arg); break; @@ -6384,7 +6384,7 @@ static int saa7134_tda8290_callback(struct saa7134_dev *dev, int ret; switch (dev->board) { - case SAA7134_BOARD_HAUPPAUGE_HVR1120: + case SAA7134_BOARD_HAUPPAUGE_HVR1150: case SAA7134_BOARD_HAUPPAUGE_HVR1110R3: /* tda8290 + tda18271 */ ret = saa7134_tda8290_18271_callback(dev, command, arg); @@ -6427,7 +6427,7 @@ static void hauppauge_eeprom(struct saa7134_dev *dev, u8 *eeprom_data) switch (tv.model) { case 67019: /* WinTV-HVR1110 (Retail, IR Blaster, hybrid, FM, SVid/Comp, 3.5mm audio in) */ case 67109: /* WinTV-HVR1000 (Retail, IR Receive, analog, no FM, SVid/Comp, 3.5mm audio in) */ - case 67201: /* WinTV-HVR1120 (Retail, IR Receive, hybrid, FM, SVid/Comp, 3.5mm audio in) */ + case 67201: /* WinTV-HVR1150 (Retail, IR Receive, hybrid, FM, SVid/Comp, 3.5mm audio in) */ case 67301: /* WinTV-HVR1000 (Retail, IR Receive, analog, no FM, SVid/Comp, 3.5mm audio in) */ case 67209: /* WinTV-HVR1110 (Retail, IR Receive, hybrid, FM, SVid/Comp, 3.5mm audio in) */ case 67559: /* WinTV-HVR1110 (OEM, no IR, hybrid, FM, SVid/Comp, RCA aud) */ @@ -6435,7 +6435,7 @@ static void hauppauge_eeprom(struct saa7134_dev *dev, u8 *eeprom_data) case 67579: /* WinTV-HVR1110 (OEM, no IR, hybrid, no FM) */ case 67589: /* WinTV-HVR1110 (OEM, no IR, hybrid, no FM, SVid/Comp, RCA aud) */ case 67599: /* WinTV-HVR1110 (OEM, no IR, hybrid, no FM, SVid/Comp, RCA aud) */ - case 67651: /* WinTV-HVR1120 (OEM, no IR, hybrid, FM, SVid/Comp, RCA aud) */ + case 67651: /* WinTV-HVR1150 (OEM, no IR, hybrid, FM, SVid/Comp, RCA aud) */ case 67659: /* WinTV-HVR1110 (OEM, no IR, hybrid, FM, SVid/Comp, RCA aud) */ break; default: @@ -6625,7 +6625,7 @@ int saa7134_board_init1(struct saa7134_dev *dev) saa_writeb (SAA7134_PRODUCTION_TEST_MODE, 0x00); break; - case SAA7134_BOARD_HAUPPAUGE_HVR1120: + case SAA7134_BOARD_HAUPPAUGE_HVR1150: case SAA7134_BOARD_HAUPPAUGE_HVR1110R3: /* GPIO 26 high for digital, low for analog */ saa7134_set_gpio(dev, 26, 0); @@ -6891,7 +6891,7 @@ int saa7134_board_init2(struct saa7134_dev *dev) dev->name, saa7134_boards[dev->board].name); } break; - case SAA7134_BOARD_HAUPPAUGE_HVR1120: + case SAA7134_BOARD_HAUPPAUGE_HVR1150: case SAA7134_BOARD_HAUPPAUGE_HVR1110R3: hauppauge_eeprom(dev, dev->eedata+0x80); break; diff --git a/drivers/media/video/saa7134/saa7134-dvb.c b/drivers/media/video/saa7134/saa7134-dvb.c index 31930f26ffc..ae0a7ecc46d 100644 --- a/drivers/media/video/saa7134/saa7134-dvb.c +++ b/drivers/media/video/saa7134/saa7134-dvb.c @@ -1147,7 +1147,7 @@ static int dvb_init(struct saa7134_dev *dev) &tda827x_cfg_1) < 0) goto dettach_frontend; break; - case SAA7134_BOARD_HAUPPAUGE_HVR1120: + case SAA7134_BOARD_HAUPPAUGE_HVR1150: fe0->dvb.frontend = dvb_attach(lgdt3305_attach, &hcw_lgdt3305_config, &dev->i2c_adap); diff --git a/drivers/media/video/saa7134/saa7134.h b/drivers/media/video/saa7134/saa7134.h index 82268848f26..bad5b237f21 100644 --- a/drivers/media/video/saa7134/saa7134.h +++ b/drivers/media/video/saa7134/saa7134.h @@ -278,7 +278,7 @@ struct saa7134_format { #define SAA7134_BOARD_ASUSTeK_TIGER 152 #define SAA7134_BOARD_KWORLD_PLUS_TV_ANALOG 153 #define SAA7134_BOARD_AVERMEDIA_GO_007_FM_PLUS 154 -#define SAA7134_BOARD_HAUPPAUGE_HVR1120 155 +#define SAA7134_BOARD_HAUPPAUGE_HVR1150 155 #define SAA7134_BOARD_HAUPPAUGE_HVR1110R3 156 #define SAA7134_BOARD_AVERMEDIA_STUDIO_507UA 157 #define SAA7134_BOARD_AVERMEDIA_CARDBUS_501 158 -- GitLab From 0e316ecfc851c8dd955d9fa6e0d3a46e451a46f4 Mon Sep 17 00:00:00 2001 From: Michael Krufky Date: Mon, 3 Aug 2009 16:51:33 -0300 Subject: [PATCH 1105/1342] V4L/DVB (12391): saa7134: Use correct product name for Hauppauge WinTV-HVR1120 DVB-T/Hybrid Signed-off-by: Michael Krufky Signed-off-by: Mauro Carvalho Chehab --- Documentation/video4linux/CARDLIST.saa7134 | 2 +- drivers/media/video/saa7134/saa7134-cards.c | 18 +++++++++--------- drivers/media/video/saa7134/saa7134-dvb.c | 2 +- drivers/media/video/saa7134/saa7134.h | 2 +- 4 files changed, 12 insertions(+), 12 deletions(-) diff --git a/Documentation/video4linux/CARDLIST.saa7134 b/Documentation/video4linux/CARDLIST.saa7134 index a82b767f9e7..c913e561419 100644 --- a/Documentation/video4linux/CARDLIST.saa7134 +++ b/Documentation/video4linux/CARDLIST.saa7134 @@ -154,7 +154,7 @@ 153 -> Kworld Plus TV Analog Lite PCI [17de:7128] 154 -> Avermedia AVerTV GO 007 FM Plus [1461:f31d] 155 -> Hauppauge WinTV-HVR1150 ATSC/QAM-Hybrid [0070:6706,0070:6708] -156 -> Hauppauge WinTV-HVR1110r3 DVB-T/Hybrid [0070:6707,0070:6709,0070:670a] +156 -> Hauppauge WinTV-HVR1120 DVB-T/Hybrid [0070:6707,0070:6709,0070:670a] 157 -> Avermedia AVerTV Studio 507UA [1461:a11b] 158 -> AVerMedia Cardbus TV/Radio (E501R) [1461:b7e9] 159 -> Beholder BeholdTV 505 RDS [0000:505B] diff --git a/drivers/media/video/saa7134/saa7134-cards.c b/drivers/media/video/saa7134/saa7134-cards.c index 60e74ad5967..6eebe3ef97d 100644 --- a/drivers/media/video/saa7134/saa7134-cards.c +++ b/drivers/media/video/saa7134/saa7134-cards.c @@ -3363,8 +3363,8 @@ struct saa7134_board saa7134_boards[] = { .gpio = 0x0800100, /* GPIO 23 HI for FM */ }, }, - [SAA7134_BOARD_HAUPPAUGE_HVR1110R3] = { - .name = "Hauppauge WinTV-HVR1110r3 DVB-T/Hybrid", + [SAA7134_BOARD_HAUPPAUGE_HVR1120] = { + .name = "Hauppauge WinTV-HVR1120 DVB-T/Hybrid", .audio_clock = 0x00187de7, .tuner_type = TUNER_PHILIPS_TDA8290, .radio_type = UNSET, @@ -5868,7 +5868,7 @@ struct pci_device_id saa7134_pci_tbl[] = { .device = PCI_DEVICE_ID_PHILIPS_SAA7133, .subvendor = 0x0070, .subdevice = 0x6707, - .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1110R3, + .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1120, },{ .vendor = PCI_VENDOR_ID_PHILIPS, .device = PCI_DEVICE_ID_PHILIPS_SAA7133, @@ -5880,13 +5880,13 @@ struct pci_device_id saa7134_pci_tbl[] = { .device = PCI_DEVICE_ID_PHILIPS_SAA7133, .subvendor = 0x0070, .subdevice = 0x6709, - .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1110R3, + .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1120, },{ .vendor = PCI_VENDOR_ID_PHILIPS, .device = PCI_DEVICE_ID_PHILIPS_SAA7133, .subvendor = 0x0070, .subdevice = 0x670a, - .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1110R3, + .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1120, },{ .vendor = PCI_VENDOR_ID_PHILIPS, .device = PCI_DEVICE_ID_PHILIPS_SAA7133, @@ -6364,7 +6364,7 @@ static int saa7134_tda8290_18271_callback(struct saa7134_dev *dev, case TDA18271_CALLBACK_CMD_AGC_ENABLE: /* 0 */ switch (dev->board) { case SAA7134_BOARD_HAUPPAUGE_HVR1150: - case SAA7134_BOARD_HAUPPAUGE_HVR1110R3: + case SAA7134_BOARD_HAUPPAUGE_HVR1120: ret = saa7134_tda18271_hvr11x0_toggle_agc(dev, arg); break; default: @@ -6385,7 +6385,7 @@ static int saa7134_tda8290_callback(struct saa7134_dev *dev, switch (dev->board) { case SAA7134_BOARD_HAUPPAUGE_HVR1150: - case SAA7134_BOARD_HAUPPAUGE_HVR1110R3: + case SAA7134_BOARD_HAUPPAUGE_HVR1120: /* tda8290 + tda18271 */ ret = saa7134_tda8290_18271_callback(dev, command, arg); break; @@ -6626,7 +6626,7 @@ int saa7134_board_init1(struct saa7134_dev *dev) saa_writeb (SAA7134_PRODUCTION_TEST_MODE, 0x00); break; case SAA7134_BOARD_HAUPPAUGE_HVR1150: - case SAA7134_BOARD_HAUPPAUGE_HVR1110R3: + case SAA7134_BOARD_HAUPPAUGE_HVR1120: /* GPIO 26 high for digital, low for analog */ saa7134_set_gpio(dev, 26, 0); msleep(1); @@ -6892,7 +6892,7 @@ int saa7134_board_init2(struct saa7134_dev *dev) } break; case SAA7134_BOARD_HAUPPAUGE_HVR1150: - case SAA7134_BOARD_HAUPPAUGE_HVR1110R3: + case SAA7134_BOARD_HAUPPAUGE_HVR1120: hauppauge_eeprom(dev, dev->eedata+0x80); break; case SAA7134_BOARD_HAUPPAUGE_HVR1110: diff --git a/drivers/media/video/saa7134/saa7134-dvb.c b/drivers/media/video/saa7134/saa7134-dvb.c index ae0a7ecc46d..98f3efd1e94 100644 --- a/drivers/media/video/saa7134/saa7134-dvb.c +++ b/drivers/media/video/saa7134/saa7134-dvb.c @@ -1119,7 +1119,7 @@ static int dvb_init(struct saa7134_dev *dev) &tda827x_cfg_2) < 0) goto dettach_frontend; break; - case SAA7134_BOARD_HAUPPAUGE_HVR1110R3: + case SAA7134_BOARD_HAUPPAUGE_HVR1120: fe0->dvb.frontend = dvb_attach(tda10048_attach, &hcw_tda10048_config, &dev->i2c_adap); diff --git a/drivers/media/video/saa7134/saa7134.h b/drivers/media/video/saa7134/saa7134.h index bad5b237f21..fb564f14887 100644 --- a/drivers/media/video/saa7134/saa7134.h +++ b/drivers/media/video/saa7134/saa7134.h @@ -279,7 +279,7 @@ struct saa7134_format { #define SAA7134_BOARD_KWORLD_PLUS_TV_ANALOG 153 #define SAA7134_BOARD_AVERMEDIA_GO_007_FM_PLUS 154 #define SAA7134_BOARD_HAUPPAUGE_HVR1150 155 -#define SAA7134_BOARD_HAUPPAUGE_HVR1110R3 156 +#define SAA7134_BOARD_HAUPPAUGE_HVR1120 156 #define SAA7134_BOARD_AVERMEDIA_STUDIO_507UA 157 #define SAA7134_BOARD_AVERMEDIA_CARDBUS_501 158 #define SAA7134_BOARD_BEHOLD_505RDS 159 -- GitLab From 11db906983fc6e996fcd10073843bd6f1b9a96c3 Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Mon, 3 Aug 2009 22:40:16 -0300 Subject: [PATCH 1106/1342] V4L/DVB (12393): cx88: fix regression in tuning for Geniatech X8000 MT The introduction of the zl10353 i2c gate control broke support for the Geniatech board (which is not behind an i2 gate). Add the needed parameter. Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/cx88/cx88-dvb.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/media/video/cx88/cx88-dvb.c b/drivers/media/video/cx88/cx88-dvb.c index c44e8760021..e237b507659 100644 --- a/drivers/media/video/cx88/cx88-dvb.c +++ b/drivers/media/video/cx88/cx88-dvb.c @@ -501,6 +501,7 @@ static struct zl10353_config cx88_pinnacle_hybrid_pctv = { static struct zl10353_config cx88_geniatech_x8000_mt = { .demod_address = (0x1e >> 1), .no_tuner = 1, + .disable_i2c_gate_ctrl = 1, }; static struct s5h1411_config dvico_fusionhdtv7_config = { -- GitLab From 93b999239c418cf5c668fd966ac2c5c27b8180dd Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Mon, 3 Aug 2009 22:52:59 -0300 Subject: [PATCH 1107/1342] V4L/DVB (12394): cx88: Disable xc3028 power management for Geniatech x8000 A user discovered that the Geniatech x8000 encountered a regression when the xc3028 power management was introduced. The xc3028 never recovers after setting the powerdown register, which is probably because the xc3028 reset GPIO is not properly configured. Since I do not have access to the hardware and thus cannot determine the correct GPIO configuration, just disable xc3028 power management on this board, which fixes the regression. Thanks to user "ritec" for reporting the issue and testing the fix. Cc: rictec Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/common/tuners/tuner-xc2028.c | 4 ++-- drivers/media/common/tuners/tuner-xc2028.h | 1 + drivers/media/video/cx88/cx88-cards.c | 8 ++++++++ 3 files changed, 11 insertions(+), 2 deletions(-) diff --git a/drivers/media/common/tuners/tuner-xc2028.c b/drivers/media/common/tuners/tuner-xc2028.c index aa20ce8cc66..f270e605da8 100644 --- a/drivers/media/common/tuners/tuner-xc2028.c +++ b/drivers/media/common/tuners/tuner-xc2028.c @@ -1119,8 +1119,8 @@ static int xc2028_sleep(struct dvb_frontend *fe) struct xc2028_data *priv = fe->tuner_priv; int rc = 0; - /* Avoid firmware reload on slow devices */ - if (no_poweroff) + /* Avoid firmware reload on slow devices or if PM disabled */ + if (no_poweroff || priv->ctrl.disable_power_mgmt) return 0; tuner_dbg("Putting xc2028/3028 into poweroff mode.\n"); diff --git a/drivers/media/common/tuners/tuner-xc2028.h b/drivers/media/common/tuners/tuner-xc2028.h index 19de7928a74..a90c35d50ad 100644 --- a/drivers/media/common/tuners/tuner-xc2028.h +++ b/drivers/media/common/tuners/tuner-xc2028.h @@ -38,6 +38,7 @@ struct xc2028_ctrl { unsigned int input1:1; unsigned int vhfbw7:1; unsigned int uhfbw8:1; + unsigned int disable_power_mgmt:1; unsigned int demod; enum firmware_type type:2; }; diff --git a/drivers/media/video/cx88/cx88-cards.c b/drivers/media/video/cx88/cx88-cards.c index a5cc1c1fc2d..39465301ec9 100644 --- a/drivers/media/video/cx88/cx88-cards.c +++ b/drivers/media/video/cx88/cx88-cards.c @@ -3003,6 +3003,14 @@ void cx88_setup_xc3028(struct cx88_core *core, struct xc2028_ctrl *ctl) case CX88_BOARD_DVICO_FUSIONHDTV_5_PCI_NANO: ctl->demod = XC3028_FE_OREN538; break; + case CX88_BOARD_GENIATECH_X8000_MT: + /* FIXME: For this board, the xc3028 never recovers after being + powered down (the reset GPIO probably is not set properly). + We don't have access to the hardware so we cannot determine + which GPIO is used for xc3028, so just disable power xc3028 + power management for now */ + ctl->disable_power_mgmt = 1; + break; case CX88_BOARD_WINFAST_TV2000_XP_GLOBAL: case CX88_BOARD_PROLINK_PV_GLOBAL_XTREME: case CX88_BOARD_PROLINK_PV_8000GT: -- GitLab From 83053f7fe3eb0b6b1634d24ede87f1daa01ae60c Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Thu, 6 Aug 2009 21:03:35 -0300 Subject: [PATCH 1108/1342] V4L/DVB (12399): mt9v011: Add support for controlling frame rates Implement g_parm/s_parm ioctls. Those are used to check the current frame rate (in fps) and to set it to a value. In practice, there are only 15 possible different speeds, due to chip limits. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/mt9v011.c | 89 ++++++++++++++++++++++++++++++++++- 1 file changed, 87 insertions(+), 2 deletions(-) diff --git a/drivers/media/video/mt9v011.c b/drivers/media/video/mt9v011.c index c14bf47d692..8de1316a276 100644 --- a/drivers/media/video/mt9v011.c +++ b/drivers/media/video/mt9v011.c @@ -156,7 +156,7 @@ static void set_balance(struct v4l2_subdev *sd) mt9v011_write(sd, R2D_MT9V011_RED_GAIN, red_gain); } -static void calc_fps(struct v4l2_subdev *sd) +static void calc_fps(struct v4l2_subdev *sd, u32 *numerator, u32 *denominator) { struct mt9v011 *core = to_mt9v011(sd); unsigned height, width, hblank, vblank, speed; @@ -179,6 +179,51 @@ static void calc_fps(struct v4l2_subdev *sd) v4l2_dbg(1, debug, sd, "Programmed to %u.%03u fps (%d pixel clcks)\n", tmp / 1000, tmp % 1000, t_time); + + if (numerator && denominator) { + *numerator = 1000; + *denominator = (u32)frames_per_ms; + } +} + +static u16 calc_speed(struct v4l2_subdev *sd, u32 numerator, u32 denominator) +{ + struct mt9v011 *core = to_mt9v011(sd); + unsigned height, width, hblank, vblank; + unsigned row_time, line_time; + u64 t_time, speed; + + /* Avoid bogus calculus */ + if (!numerator || !denominator) + return 0; + + height = mt9v011_read(sd, R03_MT9V011_HEIGHT); + width = mt9v011_read(sd, R04_MT9V011_WIDTH); + hblank = mt9v011_read(sd, R05_MT9V011_HBLANK); + vblank = mt9v011_read(sd, R06_MT9V011_VBLANK); + + row_time = width + 113 + hblank; + line_time = height + vblank + 1; + + t_time = core->xtal * ((u64)numerator); + /* round to the closest value */ + t_time += denominator / 2; + do_div(t_time, denominator); + + speed = t_time; + do_div(speed, row_time * line_time); + + /* Avoid having a negative value for speed */ + if (speed < 2) + speed = 0; + else + speed -= 2; + + /* Avoid speed overflow */ + if (speed > 15) + return 15; + + return (u16)speed; } static void set_res(struct v4l2_subdev *sd) @@ -207,7 +252,7 @@ static void set_res(struct v4l2_subdev *sd) mt9v011_write(sd, R03_MT9V011_HEIGHT, core->height); mt9v011_write(sd, R06_MT9V011_VBLANK, 508 - core->height); - calc_fps(sd); + calc_fps(sd, NULL, NULL); }; static int mt9v011_reset(struct v4l2_subdev *sd, u32 val) @@ -322,6 +367,44 @@ static int mt9v011_try_fmt(struct v4l2_subdev *sd, struct v4l2_format *fmt) return 0; } +static int mt9v011_g_parm(struct v4l2_subdev *sd, struct v4l2_streamparm *parms) +{ + struct v4l2_captureparm *cp = &parms->parm.capture; + + if (parms->type != V4L2_BUF_TYPE_VIDEO_CAPTURE) + return -EINVAL; + + memset(cp, 0, sizeof(struct v4l2_captureparm)); + cp->capability = V4L2_CAP_TIMEPERFRAME; + calc_fps(sd, + &cp->timeperframe.numerator, + &cp->timeperframe.denominator); + + return 0; +} + +static int mt9v011_s_parm(struct v4l2_subdev *sd, struct v4l2_streamparm *parms) +{ + struct v4l2_captureparm *cp = &parms->parm.capture; + struct v4l2_fract *tpf = &cp->timeperframe; + u16 speed; + + if (parms->type != V4L2_BUF_TYPE_VIDEO_CAPTURE) + return -EINVAL; + if (cp->extendedmode != 0) + return -EINVAL; + + speed = calc_speed(sd, tpf->numerator, tpf->denominator); + + mt9v011_write(sd, R0A_MT9V011_CLK_SPEED, speed); + v4l2_dbg(1, debug, sd, "Setting speed to %d\n", speed); + + /* Recalculate and update fps info */ + calc_fps(sd, &tpf->numerator, &tpf->denominator); + + return 0; +} + static int mt9v011_s_fmt(struct v4l2_subdev *sd, struct v4l2_format *fmt) { struct v4l2_pix_format *pix = &fmt->fmt.pix; @@ -419,6 +502,8 @@ static const struct v4l2_subdev_video_ops mt9v011_video_ops = { .enum_fmt = mt9v011_enum_fmt, .try_fmt = mt9v011_try_fmt, .s_fmt = mt9v011_s_fmt, + .g_parm = mt9v011_g_parm, + .s_parm = mt9v011_s_parm, }; static const struct v4l2_subdev_ops mt9v011_ops = { -- GitLab From d96ecda63f41350dc93c17ccb72ea24511f207a9 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Thu, 6 Aug 2009 21:53:59 -0300 Subject: [PATCH 1109/1342] V4L/DVB (12400): em28xx: Allow changing fps on webcams em28xx doesn't have temporal scaling. However, on webcams, sensors are capable of changing the output rate. So, VIDIOC_[G|S]_PARM ioctls should be passed to the sensor for it to properly set frame rate. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-video.c | 37 +++++++++++++++++++++++ 1 file changed, 37 insertions(+) diff --git a/drivers/media/video/em28xx/em28xx-video.c b/drivers/media/video/em28xx/em28xx-video.c index ff37b4c15f4..92ee9c64432 100644 --- a/drivers/media/video/em28xx/em28xx-video.c +++ b/drivers/media/video/em28xx/em28xx-video.c @@ -846,6 +846,41 @@ static int vidioc_s_std(struct file *file, void *priv, v4l2_std_id *norm) return 0; } +static int vidioc_g_parm(struct file *file, void *priv, + struct v4l2_streamparm *p) +{ + struct em28xx_fh *fh = priv; + struct em28xx *dev = fh->dev; + int rc = 0; + + if (p->type != V4L2_BUF_TYPE_VIDEO_CAPTURE) + return -EINVAL; + + if (dev->board.is_webcam) + rc = v4l2_device_call_until_err(&dev->v4l2_dev, 0, + video, g_parm, p); + else + v4l2_video_std_frame_period(dev->norm, + &p->parm.capture.timeperframe); + + return rc; +} + +static int vidioc_s_parm(struct file *file, void *priv, + struct v4l2_streamparm *p) +{ + struct em28xx_fh *fh = priv; + struct em28xx *dev = fh->dev; + + if (!dev->board.is_webcam) + return -EINVAL; + + if (p->type != V4L2_BUF_TYPE_VIDEO_CAPTURE) + return -EINVAL; + + return v4l2_device_call_until_err(&dev->v4l2_dev, 0, video, s_parm, p); +} + static const char *iname[] = { [EM28XX_VMUX_COMPOSITE1] = "Composite1", [EM28XX_VMUX_COMPOSITE2] = "Composite2", @@ -1885,6 +1920,8 @@ static const struct v4l2_ioctl_ops video_ioctl_ops = { .vidioc_qbuf = vidioc_qbuf, .vidioc_dqbuf = vidioc_dqbuf, .vidioc_s_std = vidioc_s_std, + .vidioc_g_parm = vidioc_g_parm, + .vidioc_s_parm = vidioc_s_parm, .vidioc_enum_input = vidioc_enum_input, .vidioc_g_input = vidioc_g_input, .vidioc_s_input = vidioc_s_input, -- GitLab From 2526ea6e46e41322eb98ac0e9c616273402bd661 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Fri, 7 Aug 2009 01:09:54 -0300 Subject: [PATCH 1110/1342] V4L/DVB (12401): m9v011: add vflip/hflip controls to control mirror/upside down Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/mt9v011.c | 53 +++++++++++++++++++++++++++++++++-- 1 file changed, 51 insertions(+), 2 deletions(-) diff --git a/drivers/media/video/mt9v011.c b/drivers/media/video/mt9v011.c index 8de1316a276..cc85f77a570 100644 --- a/drivers/media/video/mt9v011.c +++ b/drivers/media/video/mt9v011.c @@ -52,13 +52,34 @@ static struct v4l2_queryctrl mt9v011_qctrl[] = { .step = 1, .default_value = 0, .flags = 0, - }, + }, { + .id = V4L2_CID_HFLIP, + .type = V4L2_CTRL_TYPE_BOOLEAN, + .name = "Mirror", + .minimum = 0, + .maximum = 1, + .step = 1, + .default_value = 0, + .flags = 0, + }, { + .id = V4L2_CID_VFLIP, + .type = V4L2_CTRL_TYPE_BOOLEAN, + .name = "Vflip", + .minimum = 0, + .maximum = 1, + .step = 1, + .default_value = 0, + .flags = 0, + }, { + } }; struct mt9v011 { struct v4l2_subdev sd; unsigned width, height; unsigned xtal; + unsigned hflip:1; + unsigned vflip:1; u16 global_gain, red_bal, blue_bal; }; @@ -131,7 +152,6 @@ static const struct i2c_reg_value mt9v011_init_default[] = { { R0A_MT9V011_CLK_SPEED, 0x0000 }, { R1E_MT9V011_DIGITAL_ZOOM, 0x0000 }, - { R20_MT9V011_READ_MODE, 0x1000 }, { R07_MT9V011_OUT_CTRL, 0x0002 }, /* chip enable */ }; @@ -255,6 +275,20 @@ static void set_res(struct v4l2_subdev *sd) calc_fps(sd, NULL, NULL); }; +static void set_read_mode(struct v4l2_subdev *sd) +{ + struct mt9v011 *core = to_mt9v011(sd); + unsigned mode = 0x1000; + + if (core->hflip) + mode |= 0x4000; + + if (core->vflip) + mode |= 0x8000; + + mt9v011_write(sd, R20_MT9V011_READ_MODE, mode); +} + static int mt9v011_reset(struct v4l2_subdev *sd, u32 val) { int i; @@ -265,6 +299,7 @@ static int mt9v011_reset(struct v4l2_subdev *sd, u32 val) set_balance(sd); set_res(sd); + set_read_mode(sd); return 0; }; @@ -285,6 +320,12 @@ static int mt9v011_g_ctrl(struct v4l2_subdev *sd, struct v4l2_control *ctrl) case V4L2_CID_BLUE_BALANCE: ctrl->value = core->blue_bal; return 0; + case V4L2_CID_HFLIP: + ctrl->value = core->hflip ? 1 : 0; + return 0; + case V4L2_CID_VFLIP: + ctrl->value = core->vflip ? 1 : 0; + return 0; } return -EINVAL; } @@ -333,6 +374,14 @@ static int mt9v011_s_ctrl(struct v4l2_subdev *sd, struct v4l2_control *ctrl) case V4L2_CID_BLUE_BALANCE: core->blue_bal = ctrl->value; break; + case V4L2_CID_HFLIP: + core->hflip = ctrl->value; + set_read_mode(sd); + return 0; + case V4L2_CID_VFLIP: + core->vflip = ctrl->value; + set_read_mode(sd); + return 0; default: return -EINVAL; } -- GitLab From 9b4e845c6cbca2bcbfdb87e4d005260604226f45 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Fri, 7 Aug 2009 12:08:02 -0300 Subject: [PATCH 1111/1342] V4L/DVB (12402): em28xx: fix: some em2710 chips use a different vendor ID Thanks to hermann pitton for pointing this new variation. Tested-by: hermann pitton Signed-off-by: Mauro Carvalho Chehab --- Documentation/video4linux/CARDLIST.em28xx | 2 +- drivers/media/video/em28xx/em28xx-cards.c | 2 ++ 2 files changed, 3 insertions(+), 1 deletion(-) diff --git a/Documentation/video4linux/CARDLIST.em28xx b/Documentation/video4linux/CARDLIST.em28xx index 68c236c0184..e352d754875 100644 --- a/Documentation/video4linux/CARDLIST.em28xx +++ b/Documentation/video4linux/CARDLIST.em28xx @@ -1,5 +1,5 @@ 0 -> Unknown EM2800 video grabber (em2800) [eb1a:2800] - 1 -> Unknown EM2750/28xx video grabber (em2820/em2840) [eb1a:2820,eb1a:2821,eb1a:2860,eb1a:2861,eb1a:2870,eb1a:2881,eb1a:2883] + 1 -> Unknown EM2750/28xx video grabber (em2820/em2840) [eb1a:2710,eb1a:2820,eb1a:2821,eb1a:2860,eb1a:2861,eb1a:2870,eb1a:2881,eb1a:2883] 2 -> Terratec Cinergy 250 USB (em2820/em2840) [0ccd:0036] 3 -> Pinnacle PCTV USB 2 (em2820/em2840) [2304:0208] 4 -> Hauppauge WinTV USB 2 (em2820/em2840) [2040:4200,2040:4201] diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index d0b033bce86..6c35d789cd7 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -1549,6 +1549,8 @@ struct usb_device_id em28xx_id_table[] = { .driver_info = EM2750_BOARD_UNKNOWN }, { USB_DEVICE(0xeb1a, 0x2800), .driver_info = EM2800_BOARD_UNKNOWN }, + { USB_DEVICE(0xeb1a, 0x2710), + .driver_info = EM2820_BOARD_UNKNOWN }, { USB_DEVICE(0xeb1a, 0x2820), .driver_info = EM2820_BOARD_UNKNOWN }, { USB_DEVICE(0xeb1a, 0x2821), -- GitLab From d594317bdc716ccd8c8cf711e3827f9b6e0b766b Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Fri, 7 Aug 2009 12:13:31 -0300 Subject: [PATCH 1112/1342] V4L/DVB (12403): em28xx: properly reports some em2710 chips As reported by hermann pitton , some devices has a different chip id for em2710 (likely the older ones): em28xx: New device @ 480 Mbps (eb1a:2710, interface 0, class 0) em28xx #0: Identified as EM2710/EM2750/EM2751 webcam grabber (card=22) em28xx #0: em28xx chip ID = 17 Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 5 ++++- drivers/media/video/em28xx/em28xx-reg.h | 3 ++- 2 files changed, 6 insertions(+), 2 deletions(-) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 6c35d789cd7..c9e420e8a61 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -1840,11 +1840,14 @@ void em28xx_pre_card_setup(struct em28xx *dev) dev->chip_id = rc; switch (dev->chip_id) { + case CHIP_ID_EM2710: + em28xx_info("chip ID is em2710\n"); + break; case CHIP_ID_EM2750: em28xx_info("chip ID is em2750\n"); break; case CHIP_ID_EM2820: - em28xx_info("chip ID is em2710 or em2820\n"); + em28xx_info("chip ID is em2820 (or em2710)\n"); break; case CHIP_ID_EM2840: em28xx_info("chip ID is em2840\n"); diff --git a/drivers/media/video/em28xx/em28xx-reg.h b/drivers/media/video/em28xx/em28xx-reg.h index a2676d63cfd..6bf84bd787d 100644 --- a/drivers/media/video/em28xx/em28xx-reg.h +++ b/drivers/media/video/em28xx/em28xx-reg.h @@ -176,7 +176,8 @@ /* FIXME: Need to be populated with the other chip ID's */ enum em28xx_chip_id { - CHIP_ID_EM2820 = 18, /* Also used by em2710 */ + CHIP_ID_EM2710 = 17, + CHIP_ID_EM2820 = 18, /* Also used by some em2710 */ CHIP_ID_EM2840 = 20, CHIP_ID_EM2750 = 33, CHIP_ID_EM2860 = 34, -- GitLab From c2a6b54a9cf08d4ffeb75d70603c4a5d03ac97ad Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Sat, 8 Aug 2009 03:14:55 -0300 Subject: [PATCH 1113/1342] V4L/DVB (12406): em28xx: fix: don't do image interlacing on webcams Due to historical reasons, em28xx driver gets two consecutive frames and fold them into an unique framing, doing interlacing. While this works fine for TV images, this produces two bad effects with webcams: 1) webcam images are progressive. Merging two consecutive images produce interlacing artifacts on the image; 2) since the driver needs to get two frames, it reduces the maximum frame rate by two. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 4 +++ drivers/media/video/em28xx/em28xx-core.c | 5 ++- drivers/media/video/em28xx/em28xx-video.c | 40 ++++++++++++++++++----- drivers/media/video/em28xx/em28xx.h | 3 ++ 4 files changed, 42 insertions(+), 10 deletions(-) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index c9e420e8a61..9011a498e5b 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -2502,6 +2502,10 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev, if (em28xx_hint_sensor(dev) < 0) dev->board.is_webcam = 0; + /* It makes no sense to use de-interlacing mode on webcams */ + if (dev->board.is_webcam) + dev->progressive = 1; + /* Do board specific init and eeprom reading */ em28xx_card_setup(dev); diff --git a/drivers/media/video/em28xx/em28xx-core.c b/drivers/media/video/em28xx/em28xx-core.c index 5b78e199abd..339fffdf6bc 100644 --- a/drivers/media/video/em28xx/em28xx-core.c +++ b/drivers/media/video/em28xx/em28xx-core.c @@ -720,7 +720,10 @@ int em28xx_resolution_set(struct em28xx *dev) { int width, height; width = norm_maxw(dev); - height = norm_maxh(dev) >> 1; + height = norm_maxh(dev); + + if (!dev->progressive) + height >>= norm_maxh(dev); em28xx_set_outfmt(dev); diff --git a/drivers/media/video/em28xx/em28xx-video.c b/drivers/media/video/em28xx/em28xx-video.c index 92ee9c64432..ab079d9256c 100644 --- a/drivers/media/video/em28xx/em28xx-video.c +++ b/drivers/media/video/em28xx/em28xx-video.c @@ -194,15 +194,24 @@ static void em28xx_copy_video(struct em28xx *dev, startread = p; remain = len; - /* Interlaces frame */ - if (buf->top_field) + if (dev->progressive) fieldstart = outp; - else - fieldstart = outp + bytesperline; + else { + /* Interlaces two half frames */ + if (buf->top_field) + fieldstart = outp; + else + fieldstart = outp + bytesperline; + } linesdone = dma_q->pos / bytesperline; currlinedone = dma_q->pos % bytesperline; - offset = linesdone * bytesperline * 2 + currlinedone; + + if (dev->progressive) + offset = linesdone * bytesperline + currlinedone; + else + offset = linesdone * bytesperline * 2 + currlinedone; + startwrite = fieldstart + offset; lencopy = bytesperline - currlinedone; lencopy = lencopy > remain ? remain : lencopy; @@ -376,7 +385,7 @@ static inline int em28xx_isoc_copy(struct em28xx *dev, struct urb *urb) em28xx_isocdbg("Video frame %d, length=%i, %s\n", p[2], len, (p[2] & 1) ? "odd" : "even"); - if (!(p[2] & 1)) { + if (dev->progressive || !(p[2] & 1)) { if (buf != NULL) buffer_filled(dev, dma_q, buf); get_next_buf(dma_q, &buf); @@ -689,7 +698,10 @@ static int vidioc_g_fmt_vid_cap(struct file *file, void *priv, f->fmt.pix.colorspace = V4L2_COLORSPACE_SMPTE170M; /* FIXME: TOP? NONE? BOTTOM? ALTENATE? */ - f->fmt.pix.field = dev->interlaced ? + if (dev->progressive) + f->fmt.pix.field = V4L2_FIELD_NONE; + else + f->fmt.pix.field = dev->interlaced ? V4L2_FIELD_INTERLACED : V4L2_FIELD_TOP; mutex_unlock(&dev->lock); @@ -753,7 +765,11 @@ static int vidioc_try_fmt_vid_cap(struct file *file, void *priv, f->fmt.pix.bytesperline = (dev->width * fmt->depth + 7) >> 3; f->fmt.pix.sizeimage = f->fmt.pix.bytesperline * height; f->fmt.pix.colorspace = V4L2_COLORSPACE_SMPTE170M; - f->fmt.pix.field = V4L2_FIELD_INTERLACED; + if (dev->progressive) + f->fmt.pix.field = V4L2_FIELD_NONE; + else + f->fmt.pix.field = dev->interlaced ? + V4L2_FIELD_INTERLACED : V4L2_FIELD_TOP; return 0; } @@ -1659,6 +1675,7 @@ static int em28xx_v4l2_open(struct file *filp) struct em28xx *dev; enum v4l2_buf_type fh_type; struct em28xx_fh *fh; + enum v4l2_field field; dev = em28xx_get_device(minor, &fh_type, &radio); @@ -1700,8 +1717,13 @@ static int em28xx_v4l2_open(struct file *filp) dev->users++; + if (dev->progressive) + field = V4L2_FIELD_NONE; + else + field = V4L2_FIELD_INTERLACED; + videobuf_queue_vmalloc_init(&fh->vb_vidq, &em28xx_video_qops, - NULL, &dev->slock, fh->type, V4L2_FIELD_INTERLACED, + NULL, &dev->slock, fh->type, field, sizeof(struct em28xx_buffer), fh); mutex_unlock(&dev->lock); diff --git a/drivers/media/video/em28xx/em28xx.h b/drivers/media/video/em28xx/em28xx.h index 45bd513f62d..8c2dc38bca9 100644 --- a/drivers/media/video/em28xx/em28xx.h +++ b/drivers/media/video/em28xx/em28xx.h @@ -484,6 +484,9 @@ struct em28xx { int sensor_xres, sensor_yres; int sensor_xtal; + /* Allows progressive (e. g. non-interlaced) mode */ + int progressive; + /* Vinmode/Vinctl used at the driver */ int vinmode, vinctl; -- GitLab From 970cff36c0850e8193ac1162e42c7c11001b872d Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Sat, 8 Aug 2009 03:28:41 -0300 Subject: [PATCH 1114/1342] V4L/DVB (12407): em28xx: Adjust Silvercrest xtal frequency We don't know the xtal frequency of Silvercrest, but we need to have some value in order to allow controlling the frame rate frequency. The value is probably still wrong, since the manufacturer announces this device as being capable of 30fps, but the maximum we can get is 13.5 fps. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 9011a498e5b..fc46032bfe2 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -1785,7 +1785,7 @@ static int em28xx_hint_sensor(struct em28xx *dev) dev->em28xx_sensor = EM28XX_MT9V011; dev->sensor_xres = 640; dev->sensor_yres = 480; - dev->sensor_xtal = 6300000; + dev->sensor_xtal = 12150000; /* probably means GRGB 16 bit bayer */ dev->vinmode = 0x0d; -- GitLab From fcd20e3c369caf7a3fec300c9c183b25a06e21b2 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Mon, 10 Aug 2009 02:57:57 -0300 Subject: [PATCH 1115/1342] V4L/DVB (12410): em28xx: Move the non-board dependent part to be outside em28xx_pre_card_setup() em28xx_pre_card_setup() is meant to contain board-specific initialization. Also, as autodetection sometimes occur only after having i2c bus enabled, this function may need to be called later. Moving those setups to happen outside the function avoids calling it twice without need and without duplicating output lines at dmesg. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 111 +++++++++++----------- 1 file changed, 53 insertions(+), 58 deletions(-) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index fc46032bfe2..6b2b5d3e2fa 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -1821,63 +1821,6 @@ static int em28xx_hint_sensor(struct em28xx *dev) */ void em28xx_pre_card_setup(struct em28xx *dev) { - int rc; - - em28xx_set_model(dev); - - em28xx_info("Identified as %s (card=%d)\n", - dev->board.name, dev->model); - - /* Set the default GPO/GPIO for legacy devices */ - dev->reg_gpo_num = EM2880_R04_GPO; - dev->reg_gpio_num = EM28XX_R08_GPIO; - - dev->wait_after_write = 5; - - /* Based on the Chip ID, set the device configuration */ - rc = em28xx_read_reg(dev, EM28XX_R0A_CHIPID); - if (rc > 0) { - dev->chip_id = rc; - - switch (dev->chip_id) { - case CHIP_ID_EM2710: - em28xx_info("chip ID is em2710\n"); - break; - case CHIP_ID_EM2750: - em28xx_info("chip ID is em2750\n"); - break; - case CHIP_ID_EM2820: - em28xx_info("chip ID is em2820 (or em2710)\n"); - break; - case CHIP_ID_EM2840: - em28xx_info("chip ID is em2840\n"); - break; - case CHIP_ID_EM2860: - em28xx_info("chip ID is em2860\n"); - break; - case CHIP_ID_EM2870: - em28xx_info("chip ID is em2870\n"); - dev->wait_after_write = 0; - break; - case CHIP_ID_EM2874: - em28xx_info("chip ID is em2874\n"); - dev->reg_gpio_num = EM2874_R80_GPIO; - dev->wait_after_write = 0; - break; - case CHIP_ID_EM2883: - em28xx_info("chip ID is em2882/em2883\n"); - dev->wait_after_write = 0; - break; - default: - em28xx_info("em28xx chip ID = %d\n", dev->chip_id); - } - } - - /* Prepopulate cached GPO register content */ - rc = em28xx_read_reg(dev, dev->reg_gpo_num); - if (rc >= 0) - dev->reg_gpo = rc; - /* Set the initial XCLK and I2C clock values based on the board definition */ em28xx_write_reg(dev, EM28XX_R0F_XCLK, dev->board.xclk & 0x7f); @@ -2443,7 +2386,7 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev, int minor) { struct em28xx *dev = *devhandle; - int retval = -ENOMEM; + int retval; int errCode; dev->udev = udev; @@ -2460,6 +2403,58 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev, dev->em28xx_read_reg_req = em28xx_read_reg_req; dev->board.is_em2800 = em28xx_boards[dev->model].is_em2800; + em28xx_set_model(dev); + + /* Set the default GPO/GPIO for legacy devices */ + dev->reg_gpo_num = EM2880_R04_GPO; + dev->reg_gpio_num = EM28XX_R08_GPIO; + + dev->wait_after_write = 5; + + /* Based on the Chip ID, set the device configuration */ + retval = em28xx_read_reg(dev, EM28XX_R0A_CHIPID); + if (retval > 0) { + dev->chip_id = retval; + + switch (dev->chip_id) { + case CHIP_ID_EM2710: + em28xx_info("chip ID is em2710\n"); + break; + case CHIP_ID_EM2750: + em28xx_info("chip ID is em2750\n"); + break; + case CHIP_ID_EM2820: + em28xx_info("chip ID is em2820 (or em2710)\n"); + break; + case CHIP_ID_EM2840: + em28xx_info("chip ID is em2840\n"); + break; + case CHIP_ID_EM2860: + em28xx_info("chip ID is em2860\n"); + break; + case CHIP_ID_EM2870: + em28xx_info("chip ID is em2870\n"); + dev->wait_after_write = 0; + break; + case CHIP_ID_EM2874: + em28xx_info("chip ID is em2874\n"); + dev->reg_gpio_num = EM2874_R80_GPIO; + dev->wait_after_write = 0; + break; + case CHIP_ID_EM2883: + em28xx_info("chip ID is em2882/em2883\n"); + dev->wait_after_write = 0; + break; + default: + em28xx_info("em28xx chip ID = %d\n", dev->chip_id); + } + } + + /* Prepopulate cached GPO register content */ + retval = em28xx_read_reg(dev, dev->reg_gpo_num); + if (retval >= 0) + dev->reg_gpo = retval; + em28xx_pre_card_setup(dev); if (!dev->board.is_em2800) { -- GitLab From 3d3215c4e4cfca74e5805a8506d50a6752172e81 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Mon, 10 Aug 2009 10:29:27 -0300 Subject: [PATCH 1116/1342] V4L/DVB (12411): em28xx: Fix artifacts with Silvercrest webcam Silvercrest mt9v011 sensor produces a 640x480 image. However, previously, the code were getting only half of the lines and merging two consecutive frames to "produce" a 640x480 image. With the addition of progressive mode, now em28xx is working with a full image. However, when the number of lines is bigger than 240, the beginning of some odd lines are filled with blank. After lots of testing, and physically checking the device for a Xtal, it was noticed experimentally that mt9v011 is using em28xx XCLK as its clock. Due to that, changing XCLK value changes the maximum speed of the stream. At the tests, it were possible to produce up to 32 fps, using a 30 MHz XCLK. However, at that rate, the artifacts happen even at 320x240. Lower values of XCLK produces artifacts only at 640x480. At some values of xclk (for example XCLKK = 6 MHz, 640x480), it is possible to see an invalid sucession of artifacts with this pattern: .xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ..xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ...xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ....xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx .xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ..xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ...xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ....xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx (where the dots represent the blanked pixels) So, it seems that a waveform in the format of a ramp is interferring at the image. The cause of this interference is currently unknown. Some possibilities are: - electrical interference (maybe this device is broken?); - some issue at mt9v011 programming; - some bug at em28xx chip. So, for now, let's be conservative and use a value of XCLK that we know for sure that it won't cause artifacts. As I'm waiting for more of such devices with different em28xx chipset revisions, I'll have the opportunity to double check the issue with other pieces of hardware. Later patches can vary XCLK depending on the vertical resolutions, if a proper fix is not discovered. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 50 +++++++++++++++-------- 1 file changed, 34 insertions(+), 16 deletions(-) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 6b2b5d3e2fa..54429b629b2 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -218,7 +218,7 @@ static struct em28xx_reg_seq silvercrest_reg_seq[] = { struct em28xx_board em28xx_boards[] = { [EM2750_BOARD_UNKNOWN] = { .name = "EM2710/EM2750/EM2751 webcam grabber", - .xclk = EM28XX_XCLK_FREQUENCY_48MHZ, + .xclk = EM28XX_XCLK_FREQUENCY_20MHZ, .tuner_type = TUNER_ABSENT, .is_webcam = 1, .input = { { @@ -1768,6 +1768,7 @@ static int em28xx_hint_sensor(struct em28xx *dev) __be16 version_be; u16 version; + /* Micron sensor detection */ dev->i2c_client.addr = 0xba >> 1; cmd = 0; i2c_master_send(&dev->i2c_client, &cmd, 1); @@ -1776,16 +1777,27 @@ static int em28xx_hint_sensor(struct em28xx *dev) return -EINVAL; version = be16_to_cpu(version_be); - switch (version) { case 0x8232: /* mt9v011 640x480 1.3 Mpix sensor */ case 0x8243: /* mt9v011 rev B 640x480 1.3 Mpix sensor */ dev->model = EM2820_BOARD_SILVERCREST_WEBCAM; + em28xx_set_model(dev); + sensor_name = "mt9v011"; dev->em28xx_sensor = EM28XX_MT9V011; dev->sensor_xres = 640; dev->sensor_yres = 480; - dev->sensor_xtal = 12150000; + /* + * FIXME: mt9v011 uses I2S speed as xtal clk - at least with + * the Silvercrest cam I have here for testing - for higher + * resolutions, a high clock cause horizontal artifacts, so we + * need to use a lower xclk frequency. + * Yet, it would be possible to adjust xclk depending on the + * desired resolution, since this affects directly the + * frame rate. + */ + dev->board.xclk = EM28XX_XCLK_FREQUENCY_4_3MHZ; + dev->sensor_xtal = 4300000; /* probably means GRGB 16 bit bayer */ dev->vinmode = 0x0d; @@ -1794,6 +1806,8 @@ static int em28xx_hint_sensor(struct em28xx *dev) break; case 0x8431: dev->model = EM2750_BOARD_UNKNOWN; + em28xx_set_model(dev); + sensor_name = "mt9m001"; dev->em28xx_sensor = EM28XX_MT9M001; em28xx_initialize_mt9m001(dev); @@ -1810,6 +1824,9 @@ static int em28xx_hint_sensor(struct em28xx *dev) return -EINVAL; } + /* Setup webcam defaults */ + em28xx_pre_card_setup(dev); + em28xx_errdev("Sensor is %s, using model %s entry.\n", sensor_name, em28xx_boards[dev->model].name); @@ -2169,7 +2186,20 @@ void em28xx_register_i2c_ir(struct em28xx *dev) void em28xx_card_setup(struct em28xx *dev) { - em28xx_set_model(dev); + /* + * If the device can be a webcam, seek for a sensor. + * If sensor is not found, then it isn't a webcam. + */ + if (dev->board.is_webcam) { + if (em28xx_hint_sensor(dev) < 0) + dev->board.is_webcam = 0; + else + dev->progressive = 1; + } else + em28xx_set_model(dev); + + em28xx_info("Identified as %s (card=%d)\n", + dev->board.name, dev->model); dev->tuner_type = em28xx_boards[dev->model].tuner_type; if (em28xx_boards[dev->model].tuner_addr) @@ -2489,18 +2519,6 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev, dev->vinmode = 0x10; dev->vinctl = 0x11; - /* - * If the device can be a webcam, seek for a sensor. - * If sensor is not found, then it isn't a webcam. - */ - if (dev->board.is_webcam) - if (em28xx_hint_sensor(dev) < 0) - dev->board.is_webcam = 0; - - /* It makes no sense to use de-interlacing mode on webcams */ - if (dev->board.is_webcam) - dev->progressive = 1; - /* Do board specific init and eeprom reading */ em28xx_card_setup(dev); -- GitLab From d7612c86d099939503c2f849a523dbca753d1935 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Fri, 7 Aug 2009 18:43:00 -0300 Subject: [PATCH 1117/1342] V4L/DVB (12405): em28xx-cards: move register 0x13 setting to the proper place Register 0x13 seems to be a sort of image control, maybe gamma, white level or black level. Lower values produce better images, while higher values increases the contrast and shifts colors to green. 0xff produces a black image. This register is not Silvercrest-specific, so its code should be moved to a better place. If this register is left alone, a random value can be found at the register, producing weird results. While here, let's remove register 0x0d, as it had no noticed effect at the image. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 4 ---- drivers/media/video/em28xx/em28xx-core.c | 3 +++ 2 files changed, 3 insertions(+), 4 deletions(-) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 54429b629b2..ed281f56594 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -2273,10 +2273,6 @@ void em28xx_card_setup(struct em28xx *dev) em28xx_gpio_set(dev, dev->board.tuner_gpio); em28xx_set_mode(dev, EM28XX_ANALOG_MODE); break; - case EM2820_BOARD_SILVERCREST_WEBCAM: - /* FIXME: need to document the registers bellow */ - em28xx_write_reg(dev, 0x0d, 0x42); - em28xx_write_reg(dev, 0x13, 0x08); } if (dev->board.has_snapshot_button) diff --git a/drivers/media/video/em28xx/em28xx-core.c b/drivers/media/video/em28xx/em28xx-core.c index 339fffdf6bc..98e140b5d95 100644 --- a/drivers/media/video/em28xx/em28xx-core.c +++ b/drivers/media/video/em28xx/em28xx-core.c @@ -632,6 +632,9 @@ int em28xx_capture_start(struct em28xx *dev, int start) return rc; } + if (dev->board.is_webcam) + rc = em28xx_write_reg(dev, 0x13, 0x0c); + /* enable video capture */ rc = em28xx_write_reg(dev, 0x48, 0x00); -- GitLab From 7d2e2e35fb50f381c9398e481aac1e1729765ae3 Mon Sep 17 00:00:00 2001 From: Randy Dunlap Date: Wed, 5 Aug 2009 12:58:47 -0300 Subject: [PATCH 1118/1342] V4L/DVB (12422): media/zr364xx: fix build errors Fix build errors in zr364xx by adding selects: zr364xx.c:(.text+0x195ed7): undefined reference to `videobuf_streamon' zr364xx.c:(.text+0x196030): undefined reference to `videobuf_dqbuf' zr364xx.c:(.text+0x1960c4): undefined reference to `videobuf_qbuf' zr364xx.c:(.text+0x196123): undefined reference to `videobuf_querybuf' zr364xx.c:(.text+0x196182): undefined reference to `videobuf_reqbufs' zr364xx.c:(.text+0x196224): undefined reference to `videobuf_queue_is_busy' zr364xx.c:(.text+0x196390): undefined reference to `videobuf_vmalloc_free' zr364xx.c:(.text+0x196571): undefined reference to `videobuf_iolock' zr364xx.c:(.text+0x196678): undefined reference to `videobuf_mmap_mapper' zr364xx.c:(.text+0x196760): undefined reference to `videobuf_poll_stream' zr364xx.c:(.text+0x19689a): undefined reference to `videobuf_read_one' zr364xx.c:(.text+0x1969ec): undefined reference to `videobuf_mmap_free' zr364xx.c:(.text+0x197862): undefined reference to `videobuf_queue_vmalloc_init' zr364xx.c:(.text+0x197a28): undefined reference to `videobuf_streamoff' zr364xx.c:(.text+0x198203): undefined reference to `videobuf_to_vmalloc' zr364xx.c:(.text+0x198603): undefined reference to `videobuf_streamoff' drivers/built-in.o: In function `free_buffer': zr364xx.c:(.text+0x19930c): undefined reference to `videobuf_vmalloc_free' drivers/built-in.o: In function `zr364xx_open': zr364xx.c:(.text+0x19a7de): undefined reference to `videobuf_queue_vmalloc_init' drivers/built-in.o: In function `read_pipe_completion': zr364xx.c:(.text+0x19b17f): undefined reference to `videobuf_to_vmalloc' Signed-off-by: Randy Dunlap Signed-off-by: Douglas Schilling Landgraf Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/Kconfig | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/media/video/Kconfig b/drivers/media/video/Kconfig index 84b6fc15519..dcf9fa9264b 100644 --- a/drivers/media/video/Kconfig +++ b/drivers/media/video/Kconfig @@ -920,6 +920,8 @@ source "drivers/media/video/pwc/Kconfig" config USB_ZR364XX tristate "USB ZR364XX Camera support" depends on VIDEO_V4L2 + select VIDEOBUF_GEN + select VIDEOBUF_VMALLOC ---help--- Say Y here if you want to connect this type of camera to your computer's USB port. -- GitLab From 2dd54a54c19d0e5b50f4e1c591653772ead9d4a1 Mon Sep 17 00:00:00 2001 From: Guennadi Liakhovetski Date: Wed, 5 Aug 2009 20:06:31 -0300 Subject: [PATCH 1119/1342] V4L/DVB (12424): soc-camera: fix recursive locking in .buf_queue() The .buf_queue() V4L2 driver method is called under spinlock_irqsave(q->irqlock,...), don't take the lock again inside the function. Reported-by: Antonio Ospite Signed-off-by: Guennadi Liakhovetski Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/mx1_camera.c | 6 +----- drivers/media/video/mx3_camera.c | 19 ++++++++++--------- drivers/media/video/pxa_camera.c | 6 +----- drivers/media/video/sh_mobile_ceu_camera.c | 5 +---- 4 files changed, 13 insertions(+), 23 deletions(-) diff --git a/drivers/media/video/mx1_camera.c b/drivers/media/video/mx1_camera.c index 2d075205bdf..736c31d2319 100644 --- a/drivers/media/video/mx1_camera.c +++ b/drivers/media/video/mx1_camera.c @@ -234,6 +234,7 @@ static int mx1_camera_setup_dma(struct mx1_camera_dev *pcdev) return ret; } +/* Called under spinlock_irqsave(&pcdev->lock, ...) */ static void mx1_videobuf_queue(struct videobuf_queue *vq, struct videobuf_buffer *vb) { @@ -241,13 +242,10 @@ static void mx1_videobuf_queue(struct videobuf_queue *vq, struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); struct mx1_camera_dev *pcdev = ici->priv; struct mx1_buffer *buf = container_of(vb, struct mx1_buffer, vb); - unsigned long flags; dev_dbg(&icd->dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__, vb, vb->baddr, vb->bsize); - spin_lock_irqsave(&pcdev->lock, flags); - list_add_tail(&vb->queue, &pcdev->capture); vb->state = VIDEOBUF_ACTIVE; @@ -264,8 +262,6 @@ static void mx1_videobuf_queue(struct videobuf_queue *vq, __raw_writel(temp, pcdev->base + CSICR1); } } - - spin_unlock_irqrestore(&pcdev->lock, flags); } static void mx1_videobuf_release(struct videobuf_queue *vq, diff --git a/drivers/media/video/mx3_camera.c b/drivers/media/video/mx3_camera.c index e605c076ed8..9770cb7932c 100644 --- a/drivers/media/video/mx3_camera.c +++ b/drivers/media/video/mx3_camera.c @@ -332,7 +332,10 @@ static enum pixel_fmt fourcc_to_ipu_pix(__u32 fourcc) } } -/* Called with .vb_lock held */ +/* + * Called with .vb_lock mutex held and + * under spinlock_irqsave(&mx3_cam->lock, ...) + */ static void mx3_videobuf_queue(struct videobuf_queue *vq, struct videobuf_buffer *vb) { @@ -346,7 +349,8 @@ static void mx3_videobuf_queue(struct videobuf_queue *vq, struct idmac_video_param *video = &ichan->params.video; const struct soc_camera_data_format *data_fmt = icd->current_fmt; dma_cookie_t cookie; - unsigned long flags; + + BUG_ON(!irqs_disabled()); /* This is the configuration of one sg-element */ video->out_pixel_fmt = fourcc_to_ipu_pix(data_fmt->fourcc); @@ -359,8 +363,6 @@ static void mx3_videobuf_queue(struct videobuf_queue *vq, memset((void *)vb->baddr, 0xaa, vb->bsize); #endif - spin_lock_irqsave(&mx3_cam->lock, flags); - list_add_tail(&vb->queue, &mx3_cam->capture); if (!mx3_cam->active) { @@ -370,24 +372,23 @@ static void mx3_videobuf_queue(struct videobuf_queue *vq, vb->state = VIDEOBUF_QUEUED; } - spin_unlock_irqrestore(&mx3_cam->lock, flags); + spin_unlock_irq(&mx3_cam->lock); cookie = txd->tx_submit(txd); dev_dbg(&icd->dev, "Submitted cookie %d DMA 0x%08x\n", cookie, sg_dma_address(&buf->sg)); + + spin_lock_irq(&mx3_cam->lock); + if (cookie >= 0) return; /* Submit error */ vb->state = VIDEOBUF_PREPARED; - spin_lock_irqsave(&mx3_cam->lock, flags); - list_del_init(&vb->queue); if (mx3_cam->active == buf) mx3_cam->active = NULL; - - spin_unlock_irqrestore(&mx3_cam->lock, flags); } /* Called with .vb_lock held */ diff --git a/drivers/media/video/pxa_camera.c b/drivers/media/video/pxa_camera.c index e048d25798c..016bb45ba0c 100644 --- a/drivers/media/video/pxa_camera.c +++ b/drivers/media/video/pxa_camera.c @@ -612,6 +612,7 @@ static void pxa_camera_stop_capture(struct pxa_camera_dev *pcdev) dev_dbg(pcdev->soc_host.dev, "%s\n", __func__); } +/* Called under spinlock_irqsave(&pcdev->lock, ...) */ static void pxa_videobuf_queue(struct videobuf_queue *vq, struct videobuf_buffer *vb) { @@ -619,13 +620,10 @@ static void pxa_videobuf_queue(struct videobuf_queue *vq, struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); struct pxa_camera_dev *pcdev = ici->priv; struct pxa_buffer *buf = container_of(vb, struct pxa_buffer, vb); - unsigned long flags; dev_dbg(&icd->dev, "%s (vb=0x%p) 0x%08lx %d active=%p\n", __func__, vb, vb->baddr, vb->bsize, pcdev->active); - spin_lock_irqsave(&pcdev->lock, flags); - list_add_tail(&vb->queue, &pcdev->capture); vb->state = VIDEOBUF_ACTIVE; @@ -633,8 +631,6 @@ static void pxa_videobuf_queue(struct videobuf_queue *vq, if (!pcdev->active) pxa_camera_start_capture(pcdev); - - spin_unlock_irqrestore(&pcdev->lock, flags); } static void pxa_videobuf_release(struct videobuf_queue *vq, diff --git a/drivers/media/video/sh_mobile_ceu_camera.c b/drivers/media/video/sh_mobile_ceu_camera.c index 0db88a53d92..e86878deea7 100644 --- a/drivers/media/video/sh_mobile_ceu_camera.c +++ b/drivers/media/video/sh_mobile_ceu_camera.c @@ -282,27 +282,24 @@ out: return ret; } +/* Called under spinlock_irqsave(&pcdev->lock, ...) */ static void sh_mobile_ceu_videobuf_queue(struct videobuf_queue *vq, struct videobuf_buffer *vb) { struct soc_camera_device *icd = vq->priv_data; struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); struct sh_mobile_ceu_dev *pcdev = ici->priv; - unsigned long flags; dev_dbg(&icd->dev, "%s (vb=0x%p) 0x%08lx %zd\n", __func__, vb, vb->baddr, vb->bsize); vb->state = VIDEOBUF_QUEUED; - spin_lock_irqsave(&pcdev->lock, flags); list_add_tail(&vb->queue, &pcdev->capture); if (!pcdev->active) { pcdev->active = vb; sh_mobile_ceu_capture(pcdev); } - - spin_unlock_irqrestore(&pcdev->lock, flags); } static void sh_mobile_ceu_videobuf_release(struct videobuf_queue *vq, -- GitLab From 99362e1ece9f9651af1b849a01d91b9df1e0db2c Mon Sep 17 00:00:00 2001 From: Hans Verkuil Date: Fri, 7 Aug 2009 07:10:52 -0300 Subject: [PATCH 1120/1342] V4L/DVB (12428): hdpvr: add missing initialization of current_norm Drivers should either set current_norm or supply a g_std callback. The hdpvr driver does neither. Since it initializes to a 60 Hz format I've initialized the current_norm to NTSC | PAL_M | PAL_60 which is the 60 Hz subset of tvnorms. Cc: Janne Grunau Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/hdpvr/hdpvr-video.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/media/video/hdpvr/hdpvr-video.c b/drivers/media/video/hdpvr/hdpvr-video.c index ccd47f57f42..d678765cbba 100644 --- a/drivers/media/video/hdpvr/hdpvr-video.c +++ b/drivers/media/video/hdpvr/hdpvr-video.c @@ -1220,6 +1220,8 @@ static const struct video_device hdpvr_video_template = { V4L2_STD_PAL_G | V4L2_STD_PAL_H | V4L2_STD_PAL_I | V4L2_STD_PAL_D | V4L2_STD_PAL_M | V4L2_STD_PAL_N | V4L2_STD_PAL_60, + .current_norm = V4L2_STD_NTSC | V4L2_STD_PAL_M | + V4L2_STD_PAL_60, }; int hdpvr_register_videodev(struct hdpvr_device *dev, struct device *parent, -- GitLab From 9bedc7f7fe803c17d26b5fcf5786b50a7cf40def Mon Sep 17 00:00:00 2001 From: Hans Verkuil Date: Fri, 7 Aug 2009 07:28:16 -0300 Subject: [PATCH 1121/1342] V4L/DVB (12429): v4l2-ioctl: fix G_STD and G_PARM default handlers The v4l core supplies default handlers for G_STD and G_PARM. However, both default handlers are buggy. This patch fixes the following: 1) If no g_std is supplied and current_norm == 0, then this driver does not support TV video standards (e.g. a radio or webcam driver). Return -EINVAL. This ensures that there is no bogus VIDIOC_G_STD support for such drivers. 2) The default VIDIOC_G_PARM handler used current_norm instead of first checking if the driver supported g_std and calling that to get the norm. It also didn't check if current_norm was 0, since in that case the driver does not support TV standards (or no standard was set at all) and the default handler should return -EINVAL. Note that I am very unhappy with these default handlers: I think they basically behave like some very strange and unexpected side-effect. Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/v4l2-ioctl.c | 15 ++++++++++++--- 1 file changed, 12 insertions(+), 3 deletions(-) diff --git a/drivers/media/video/v4l2-ioctl.c b/drivers/media/video/v4l2-ioctl.c index be64a502ea2..f2afc4e0837 100644 --- a/drivers/media/video/v4l2-ioctl.c +++ b/drivers/media/video/v4l2-ioctl.c @@ -1081,8 +1081,10 @@ static long __video_do_ioctl(struct file *file, /* Calls the specific handler */ if (ops->vidioc_g_std) ret = ops->vidioc_g_std(file, fh, id); - else + else if (vfd->current_norm) *id = vfd->current_norm; + else + ret = -EINVAL; if (!ret) dbgarg(cmd, "std=0x%08Lx\n", (long long unsigned)*id); @@ -1553,12 +1555,19 @@ static long __video_do_ioctl(struct file *file, break; ret = ops->vidioc_g_parm(file, fh, p); } else { + v4l2_std_id std = vfd->current_norm; + if (p->type != V4L2_BUF_TYPE_VIDEO_CAPTURE) return -EINVAL; - v4l2_video_std_frame_period(vfd->current_norm, - &p->parm.capture.timeperframe); ret = 0; + if (ops->vidioc_g_std) + ret = ops->vidioc_g_std(file, fh, &std); + else if (std == 0) + ret = -EINVAL; + if (ret == 0) + v4l2_video_std_frame_period(std, + &p->parm.capture.timeperframe); } dbgarg(cmd, "type=%d\n", p->type); -- GitLab From 01a5fd6ff3fbae9a599d3334a8cca0f00865e360 Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Fri, 7 Aug 2009 09:25:06 -0300 Subject: [PATCH 1122/1342] V4L/DVB (12432): em28xx: fix regression in Empire DualTV digital tuning Restore support for digital tuning caused by regression during introduction of disable_i2c_gate parameter to zl10353 driver. Thanks to user "Xwang" for reporting the problem and testing the fix Cc: Xwang Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-dvb.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/media/video/em28xx/em28xx-dvb.c b/drivers/media/video/em28xx/em28xx-dvb.c index cf0ac7f2a30..d603575431b 100644 --- a/drivers/media/video/em28xx/em28xx-dvb.c +++ b/drivers/media/video/em28xx/em28xx-dvb.c @@ -478,7 +478,6 @@ static int dvb_init(struct em28xx *dev) } break; case EM2880_BOARD_KWORLD_DVB_310U: - case EM2880_BOARD_EMPIRE_DUAL_TV: dvb->frontend = dvb_attach(zl10353_attach, &em28xx_zl10353_with_xc3028, &dev->i2c_adap); @@ -488,6 +487,7 @@ static int dvb_init(struct em28xx *dev) } break; case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900: + case EM2880_BOARD_EMPIRE_DUAL_TV: dvb->frontend = dvb_attach(zl10353_attach, &em28xx_zl10353_xc3028_no_i2c_gate, &dev->i2c_adap); -- GitLab From 77f2c2db1146154fb054e9ce955928a66d8c959f Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Mon, 10 Aug 2009 22:17:25 -0300 Subject: [PATCH 1123/1342] V4L/DVB (12436): stk-webcam: read buffer overflow It tested the value of stk_sizes[i].m before checking whether i was in range. Cc: Hans Verkuil Cc: Trent Piepho Signed-off-by: Roel Kluin Signed-off-by: Andrew Morton Signed-off-by: Douglas Schilling Landgraf Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/stk-webcam.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/media/video/stk-webcam.c b/drivers/media/video/stk-webcam.c index 4d6785e6345..b154bd961e3 100644 --- a/drivers/media/video/stk-webcam.c +++ b/drivers/media/video/stk-webcam.c @@ -1050,8 +1050,8 @@ static int stk_setup_format(struct stk_camera *dev) depth = 1; else depth = 2; - while (stk_sizes[i].m != dev->vsettings.mode - && i < ARRAY_SIZE(stk_sizes)) + while (i < ARRAY_SIZE(stk_sizes) && + stk_sizes[i].m != dev->vsettings.mode) i++; if (i == ARRAY_SIZE(stk_sizes)) { STK_ERROR("Something is broken in %s\n", __func__); -- GitLab From 27059b35397fc7cf2cbf5b4b99d912bbc06aff4d Mon Sep 17 00:00:00 2001 From: Randy Dunlap Date: Mon, 10 Aug 2009 21:59:16 -0300 Subject: [PATCH 1124/1342] V4L/DVB (12437): dvb: siano uses/depends on INPUT siano uses input_*() functions so it should depend on INPUT to prevent build errors: ERROR: "input_event" [drivers/media/dvb/siano/sms1xxx.ko] undefined! ERROR: "input_register_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined! ERROR: "input_free_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined! ERROR: "input_unregister_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined! ERROR: "input_allocate_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined! Cc: Michael Krufky Cc: Uri Shkolnik Signed-off-by: Randy Dunlap Signed-off-by: Douglas Schilling Landgraf Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb/siano/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/media/dvb/siano/Kconfig b/drivers/media/dvb/siano/Kconfig index dd863f26167..88847d1dcbb 100644 --- a/drivers/media/dvb/siano/Kconfig +++ b/drivers/media/dvb/siano/Kconfig @@ -4,7 +4,7 @@ config DVB_SIANO_SMS1XXX tristate "Siano SMS1XXX USB dongle support" - depends on DVB_CORE && USB + depends on DVB_CORE && USB && INPUT ---help--- Choose Y here if you have a USB dongle with a SMS1XXX chipset. -- GitLab From bb2b4542b6415044894cd7c147ff54840dd8ed3f Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Mon, 10 Aug 2009 22:07:54 -0300 Subject: [PATCH 1125/1342] V4L/DVB (12438): Read buffer overflow parport[n] is checked before n < MAX_CAMS Signed-off-by: Roel Kluin Signed-off-by: Douglas Schilling Landgraf Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/bw-qcam.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/media/video/bw-qcam.c b/drivers/media/video/bw-qcam.c index 10dbd4a11b3..9e39bc5f7b0 100644 --- a/drivers/media/video/bw-qcam.c +++ b/drivers/media/video/bw-qcam.c @@ -992,7 +992,7 @@ static int accept_bwqcam(struct parport *port) if (parport[0] && strncmp(parport[0], "auto", 4) != 0) { /* user gave parport parameters */ - for(n=0; parport[n] && n Date: Mon, 10 Aug 2009 22:51:01 -0300 Subject: [PATCH 1126/1342] V4L/DVB (12440): Use kzalloc for frontend states to have struct dvb_frontend properly This patch changes most frontend drivers to allocate their state structure via kzalloc and not kmalloc. This is done to properly initialize the embedded "struct dvb_frontend frontend" field, that they all have. The visible effect of this struct being uninitalized is, that the member "id" that is used to set the name of kernel thread is totally random. Some board drivers (for example cx88-dvb) set this "id" via videobuf_dvb_alloc_frontend but most do not. So I at least get random id values for saa7134, flexcop and ttpci based cards. It looks like this in dmesg: DVB: registering adapter 1 frontend -10551321 (ST STV0299 DVB-S) The related kernel thread then also gets a strange name like "kdvb-ad-1-fe--1". Cc: Michael Krufky Cc: Steven Toth Cc: Timothy Lee Cc: Igor M. Liplianin Signed-off-by: Matthias Schwarzott Acked-by: Andreas Oberritter Signed-off-by: Douglas Schilling Landgraf Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb/frontends/cx22700.c | 2 +- drivers/media/dvb/frontends/cx22702.c | 2 +- drivers/media/dvb/frontends/cx24110.c | 2 +- drivers/media/dvb/frontends/dvb_dummy_fe.c | 6 +++--- drivers/media/dvb/frontends/l64781.c | 2 +- drivers/media/dvb/frontends/lgs8gl5.c | 2 +- drivers/media/dvb/frontends/mt312.c | 2 +- drivers/media/dvb/frontends/nxt6000.c | 2 +- drivers/media/dvb/frontends/or51132.c | 2 +- drivers/media/dvb/frontends/or51211.c | 2 +- drivers/media/dvb/frontends/s5h1409.c | 2 +- drivers/media/dvb/frontends/s5h1411.c | 2 +- drivers/media/dvb/frontends/si21xx.c | 2 +- drivers/media/dvb/frontends/sp8870.c | 2 +- drivers/media/dvb/frontends/sp887x.c | 2 +- drivers/media/dvb/frontends/stv0288.c | 2 +- drivers/media/dvb/frontends/stv0297.c | 2 +- drivers/media/dvb/frontends/stv0299.c | 2 +- drivers/media/dvb/frontends/tda10021.c | 2 +- drivers/media/dvb/frontends/tda10048.c | 2 +- drivers/media/dvb/frontends/tda1004x.c | 4 ++-- drivers/media/dvb/frontends/tda10086.c | 2 +- drivers/media/dvb/frontends/tda8083.c | 2 +- drivers/media/dvb/frontends/ves1820.c | 2 +- drivers/media/dvb/frontends/ves1x93.c | 2 +- 25 files changed, 28 insertions(+), 28 deletions(-) diff --git a/drivers/media/dvb/frontends/cx22700.c b/drivers/media/dvb/frontends/cx22700.c index ace5cb17165..fbd838eca26 100644 --- a/drivers/media/dvb/frontends/cx22700.c +++ b/drivers/media/dvb/frontends/cx22700.c @@ -380,7 +380,7 @@ struct dvb_frontend* cx22700_attach(const struct cx22700_config* config, struct cx22700_state* state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct cx22700_state), GFP_KERNEL); + state = kzalloc(sizeof(struct cx22700_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ diff --git a/drivers/media/dvb/frontends/cx22702.c b/drivers/media/dvb/frontends/cx22702.c index 5d1abe34bdd..00b5c7e91d5 100644 --- a/drivers/media/dvb/frontends/cx22702.c +++ b/drivers/media/dvb/frontends/cx22702.c @@ -580,7 +580,7 @@ struct dvb_frontend *cx22702_attach(const struct cx22702_config *config, struct cx22702_state *state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct cx22702_state), GFP_KERNEL); + state = kzalloc(sizeof(struct cx22702_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/cx24110.c b/drivers/media/dvb/frontends/cx24110.c index 87ae29db024..ffbcfabd83f 100644 --- a/drivers/media/dvb/frontends/cx24110.c +++ b/drivers/media/dvb/frontends/cx24110.c @@ -598,7 +598,7 @@ struct dvb_frontend* cx24110_attach(const struct cx24110_config* config, int ret; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct cx24110_state), GFP_KERNEL); + state = kzalloc(sizeof(struct cx24110_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ diff --git a/drivers/media/dvb/frontends/dvb_dummy_fe.c b/drivers/media/dvb/frontends/dvb_dummy_fe.c index db8a937cc63..a7fc7e53a55 100644 --- a/drivers/media/dvb/frontends/dvb_dummy_fe.c +++ b/drivers/media/dvb/frontends/dvb_dummy_fe.c @@ -117,7 +117,7 @@ struct dvb_frontend* dvb_dummy_fe_ofdm_attach(void) struct dvb_dummy_fe_state* state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct dvb_dummy_fe_state), GFP_KERNEL); + state = kzalloc(sizeof(struct dvb_dummy_fe_state), GFP_KERNEL); if (state == NULL) goto error; /* create dvb_frontend */ @@ -137,7 +137,7 @@ struct dvb_frontend *dvb_dummy_fe_qpsk_attach(void) struct dvb_dummy_fe_state* state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct dvb_dummy_fe_state), GFP_KERNEL); + state = kzalloc(sizeof(struct dvb_dummy_fe_state), GFP_KERNEL); if (state == NULL) goto error; /* create dvb_frontend */ @@ -157,7 +157,7 @@ struct dvb_frontend *dvb_dummy_fe_qam_attach(void) struct dvb_dummy_fe_state* state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct dvb_dummy_fe_state), GFP_KERNEL); + state = kzalloc(sizeof(struct dvb_dummy_fe_state), GFP_KERNEL); if (state == NULL) goto error; /* create dvb_frontend */ diff --git a/drivers/media/dvb/frontends/l64781.c b/drivers/media/dvb/frontends/l64781.c index e1e70e9e0cb..3051b64aa17 100644 --- a/drivers/media/dvb/frontends/l64781.c +++ b/drivers/media/dvb/frontends/l64781.c @@ -501,7 +501,7 @@ struct dvb_frontend* l64781_attach(const struct l64781_config* config, { .addr = config->demod_address, .flags = I2C_M_RD, .buf = b1, .len = 1 } }; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct l64781_state), GFP_KERNEL); + state = kzalloc(sizeof(struct l64781_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ diff --git a/drivers/media/dvb/frontends/lgs8gl5.c b/drivers/media/dvb/frontends/lgs8gl5.c index 855852fddf2..bb37ed289a0 100644 --- a/drivers/media/dvb/frontends/lgs8gl5.c +++ b/drivers/media/dvb/frontends/lgs8gl5.c @@ -387,7 +387,7 @@ lgs8gl5_attach(const struct lgs8gl5_config *config, struct i2c_adapter *i2c) dprintk("%s\n", __func__); /* Allocate memory for the internal state */ - state = kmalloc(sizeof(struct lgs8gl5_state), GFP_KERNEL); + state = kzalloc(sizeof(struct lgs8gl5_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/mt312.c b/drivers/media/dvb/frontends/mt312.c index a621f727935..f69daaac78c 100644 --- a/drivers/media/dvb/frontends/mt312.c +++ b/drivers/media/dvb/frontends/mt312.c @@ -782,7 +782,7 @@ struct dvb_frontend *mt312_attach(const struct mt312_config *config, struct mt312_state *state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct mt312_state), GFP_KERNEL); + state = kzalloc(sizeof(struct mt312_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/nxt6000.c b/drivers/media/dvb/frontends/nxt6000.c index 0eef22dbf8a..a763ec756f7 100644 --- a/drivers/media/dvb/frontends/nxt6000.c +++ b/drivers/media/dvb/frontends/nxt6000.c @@ -545,7 +545,7 @@ struct dvb_frontend* nxt6000_attach(const struct nxt6000_config* config, struct nxt6000_state* state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct nxt6000_state), GFP_KERNEL); + state = kzalloc(sizeof(struct nxt6000_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ diff --git a/drivers/media/dvb/frontends/or51132.c b/drivers/media/dvb/frontends/or51132.c index 8133ea3cddd..38e67accb8c 100644 --- a/drivers/media/dvb/frontends/or51132.c +++ b/drivers/media/dvb/frontends/or51132.c @@ -562,7 +562,7 @@ struct dvb_frontend* or51132_attach(const struct or51132_config* config, struct or51132_state* state = NULL; /* Allocate memory for the internal state */ - state = kmalloc(sizeof(struct or51132_state), GFP_KERNEL); + state = kzalloc(sizeof(struct or51132_state), GFP_KERNEL); if (state == NULL) return NULL; diff --git a/drivers/media/dvb/frontends/or51211.c b/drivers/media/dvb/frontends/or51211.c index 16cf2fdd5d7..c709ce6771c 100644 --- a/drivers/media/dvb/frontends/or51211.c +++ b/drivers/media/dvb/frontends/or51211.c @@ -527,7 +527,7 @@ struct dvb_frontend* or51211_attach(const struct or51211_config* config, struct or51211_state* state = NULL; /* Allocate memory for the internal state */ - state = kmalloc(sizeof(struct or51211_state), GFP_KERNEL); + state = kzalloc(sizeof(struct or51211_state), GFP_KERNEL); if (state == NULL) return NULL; diff --git a/drivers/media/dvb/frontends/s5h1409.c b/drivers/media/dvb/frontends/s5h1409.c index 3e08d985d6e..fb301151842 100644 --- a/drivers/media/dvb/frontends/s5h1409.c +++ b/drivers/media/dvb/frontends/s5h1409.c @@ -796,7 +796,7 @@ struct dvb_frontend *s5h1409_attach(const struct s5h1409_config *config, u16 reg; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct s5h1409_state), GFP_KERNEL); + state = kzalloc(sizeof(struct s5h1409_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/s5h1411.c b/drivers/media/dvb/frontends/s5h1411.c index 66e2dd6d6fe..d8adf1e3201 100644 --- a/drivers/media/dvb/frontends/s5h1411.c +++ b/drivers/media/dvb/frontends/s5h1411.c @@ -844,7 +844,7 @@ struct dvb_frontend *s5h1411_attach(const struct s5h1411_config *config, u16 reg; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct s5h1411_state), GFP_KERNEL); + state = kzalloc(sizeof(struct s5h1411_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/si21xx.c b/drivers/media/dvb/frontends/si21xx.c index 0bd16af8a6c..9552a22ccff 100644 --- a/drivers/media/dvb/frontends/si21xx.c +++ b/drivers/media/dvb/frontends/si21xx.c @@ -928,7 +928,7 @@ struct dvb_frontend *si21xx_attach(const struct si21xx_config *config, dprintk("%s\n", __func__); /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct si21xx_state), GFP_KERNEL); + state = kzalloc(sizeof(struct si21xx_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/sp8870.c b/drivers/media/dvb/frontends/sp8870.c index 1c9a9b4051b..b85eb60a893 100644 --- a/drivers/media/dvb/frontends/sp8870.c +++ b/drivers/media/dvb/frontends/sp8870.c @@ -557,7 +557,7 @@ struct dvb_frontend* sp8870_attach(const struct sp8870_config* config, struct sp8870_state* state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct sp8870_state), GFP_KERNEL); + state = kzalloc(sizeof(struct sp8870_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ diff --git a/drivers/media/dvb/frontends/sp887x.c b/drivers/media/dvb/frontends/sp887x.c index 559509ab4da..4a7c3d84260 100644 --- a/drivers/media/dvb/frontends/sp887x.c +++ b/drivers/media/dvb/frontends/sp887x.c @@ -557,7 +557,7 @@ struct dvb_frontend* sp887x_attach(const struct sp887x_config* config, struct sp887x_state* state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct sp887x_state), GFP_KERNEL); + state = kzalloc(sizeof(struct sp887x_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ diff --git a/drivers/media/dvb/frontends/stv0288.c b/drivers/media/dvb/frontends/stv0288.c index ff1194de34c..2930a5d6768 100644 --- a/drivers/media/dvb/frontends/stv0288.c +++ b/drivers/media/dvb/frontends/stv0288.c @@ -570,7 +570,7 @@ struct dvb_frontend *stv0288_attach(const struct stv0288_config *config, int id; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct stv0288_state), GFP_KERNEL); + state = kzalloc(sizeof(struct stv0288_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/stv0297.c b/drivers/media/dvb/frontends/stv0297.c index 62caf802ed9..4fd7479bb62 100644 --- a/drivers/media/dvb/frontends/stv0297.c +++ b/drivers/media/dvb/frontends/stv0297.c @@ -663,7 +663,7 @@ struct dvb_frontend *stv0297_attach(const struct stv0297_config *config, struct stv0297_state *state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct stv0297_state), GFP_KERNEL); + state = kzalloc(sizeof(struct stv0297_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/stv0299.c b/drivers/media/dvb/frontends/stv0299.c index 6c1cb1973c6..96887446972 100644 --- a/drivers/media/dvb/frontends/stv0299.c +++ b/drivers/media/dvb/frontends/stv0299.c @@ -667,7 +667,7 @@ struct dvb_frontend* stv0299_attach(const struct stv0299_config* config, int id; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct stv0299_state), GFP_KERNEL); + state = kzalloc(sizeof(struct stv0299_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ diff --git a/drivers/media/dvb/frontends/tda10021.c b/drivers/media/dvb/frontends/tda10021.c index f648fdb64bb..f5d7b3277a2 100644 --- a/drivers/media/dvb/frontends/tda10021.c +++ b/drivers/media/dvb/frontends/tda10021.c @@ -413,7 +413,7 @@ struct dvb_frontend* tda10021_attach(const struct tda1002x_config* config, u8 id; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct tda10021_state), GFP_KERNEL); + state = kzalloc(sizeof(struct tda10021_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ diff --git a/drivers/media/dvb/frontends/tda10048.c b/drivers/media/dvb/frontends/tda10048.c index cc8862ce4aa..4e2a7c8b2f6 100644 --- a/drivers/media/dvb/frontends/tda10048.c +++ b/drivers/media/dvb/frontends/tda10048.c @@ -1095,7 +1095,7 @@ struct dvb_frontend *tda10048_attach(const struct tda10048_config *config, dprintk(1, "%s()\n", __func__); /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct tda10048_state), GFP_KERNEL); + state = kzalloc(sizeof(struct tda10048_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/tda1004x.c b/drivers/media/dvb/frontends/tda1004x.c index 4981cef8b44..f2a8abe0a24 100644 --- a/drivers/media/dvb/frontends/tda1004x.c +++ b/drivers/media/dvb/frontends/tda1004x.c @@ -1269,7 +1269,7 @@ struct dvb_frontend* tda10045_attach(const struct tda1004x_config* config, int id; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct tda1004x_state), GFP_KERNEL); + state = kzalloc(sizeof(struct tda1004x_state), GFP_KERNEL); if (!state) { printk(KERN_ERR "Can't alocate memory for tda10045 state\n"); return NULL; @@ -1339,7 +1339,7 @@ struct dvb_frontend* tda10046_attach(const struct tda1004x_config* config, int id; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct tda1004x_state), GFP_KERNEL); + state = kzalloc(sizeof(struct tda1004x_state), GFP_KERNEL); if (!state) { printk(KERN_ERR "Can't alocate memory for tda10046 state\n"); return NULL; diff --git a/drivers/media/dvb/frontends/tda10086.c b/drivers/media/dvb/frontends/tda10086.c index a17ce3c4ad8..f2c8faac6f3 100644 --- a/drivers/media/dvb/frontends/tda10086.c +++ b/drivers/media/dvb/frontends/tda10086.c @@ -745,7 +745,7 @@ struct dvb_frontend* tda10086_attach(const struct tda10086_config* config, dprintk ("%s\n", __func__); /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct tda10086_state), GFP_KERNEL); + state = kzalloc(sizeof(struct tda10086_state), GFP_KERNEL); if (!state) return NULL; diff --git a/drivers/media/dvb/frontends/tda8083.c b/drivers/media/dvb/frontends/tda8083.c index 5b843b2e67e..9369f7442f2 100644 --- a/drivers/media/dvb/frontends/tda8083.c +++ b/drivers/media/dvb/frontends/tda8083.c @@ -417,7 +417,7 @@ struct dvb_frontend* tda8083_attach(const struct tda8083_config* config, struct tda8083_state* state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct tda8083_state), GFP_KERNEL); + state = kzalloc(sizeof(struct tda8083_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ diff --git a/drivers/media/dvb/frontends/ves1820.c b/drivers/media/dvb/frontends/ves1820.c index a184597f1d9..6e78e486551 100644 --- a/drivers/media/dvb/frontends/ves1820.c +++ b/drivers/media/dvb/frontends/ves1820.c @@ -374,7 +374,7 @@ struct dvb_frontend* ves1820_attach(const struct ves1820_config* config, struct ves1820_state* state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct ves1820_state), GFP_KERNEL); + state = kzalloc(sizeof(struct ves1820_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/ves1x93.c b/drivers/media/dvb/frontends/ves1x93.c index bd558960bd8..8d7854c2fb0 100644 --- a/drivers/media/dvb/frontends/ves1x93.c +++ b/drivers/media/dvb/frontends/ves1x93.c @@ -456,7 +456,7 @@ struct dvb_frontend* ves1x93_attach(const struct ves1x93_config* config, u8 identity; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct ves1x93_state), GFP_KERNEL); + state = kzalloc(sizeof(struct ves1x93_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ -- GitLab From 08b39642b1e375afd014c50f6013ec4a292ca3b2 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Mon, 10 Aug 2009 22:59:33 -0300 Subject: [PATCH 1127/1342] V4L/DVB (12441): siano: read buffer overflow With mode DEVICE_MODE_RAW_TUNER a read occurs past the end of smscore_fw_lkup[]. Subsequently an attempt is made to load the firmware from the resulting filename. Signed-off-by: Roel Kluin Signed-off-by: Andrew Morton Signed-off-by: Douglas Schilling Landgraf Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb/siano/smscoreapi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/media/dvb/siano/smscoreapi.c b/drivers/media/dvb/siano/smscoreapi.c index a246903c334..bd9ab9d0d12 100644 --- a/drivers/media/dvb/siano/smscoreapi.c +++ b/drivers/media/dvb/siano/smscoreapi.c @@ -816,7 +816,7 @@ int smscore_set_device_mode(struct smscore_device_t *coredev, int mode) sms_debug("set device mode to %d", mode); if (coredev->device_flags & SMS_DEVICE_FAMILY2) { - if (mode < DEVICE_MODE_DVBT || mode > DEVICE_MODE_RAW_TUNER) { + if (mode < DEVICE_MODE_DVBT || mode >= DEVICE_MODE_RAW_TUNER) { sms_err("invalid mode specified %d", mode); return -EINVAL; } -- GitLab From a219dc4d4463809b1be473038e7d9f3437ca452d Mon Sep 17 00:00:00 2001 From: Ramax Lo Date: Wed, 12 Aug 2009 23:55:56 +0800 Subject: [PATCH 1128/1342] ARM: S3C64XX: serial: Fix a typo in Kconfig The typo causes drivers/serial/s3c6400.c not being built for s3c6400 platform. Signed-off-by: Ramax Lo Signed-off-by: Ben Dooks --- drivers/serial/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index 037c1e0b7c4..6553833c12d 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -527,7 +527,7 @@ config SERIAL_S3C24A0 config SERIAL_S3C6400 tristate "Samsung S3C6400/S3C6410 Serial port support" - depends on SERIAL_SAMSUNG && (CPU_S3C600 || CPU_S3C6410) + depends on SERIAL_SAMSUNG && (CPU_S3C6400 || CPU_S3C6410) default y help Serial port support for the Samsung S3C6400 and S3C6410 -- GitLab From 48ec45e725aa385d72bced73b267dfaf13351876 Mon Sep 17 00:00:00 2001 From: Davide Rizzo Date: Thu, 13 Aug 2009 11:53:53 +0200 Subject: [PATCH 1129/1342] ARM: S3C24XX: Fix clkout mpx error Bug correction: CLK Outputs cannot have XTAL as parent Signed-off-by: Davide Rizzo [ben-linux@fluff.org: updated patch subject] Signed-off-by: Ben Dooks --- arch/arm/plat-s3c24xx/clock-dclk.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/plat-s3c24xx/clock-dclk.c b/arch/arm/plat-s3c24xx/clock-dclk.c index 5b75a797b5a..0afb217a775 100644 --- a/arch/arm/plat-s3c24xx/clock-dclk.c +++ b/arch/arm/plat-s3c24xx/clock-dclk.c @@ -129,7 +129,7 @@ static int s3c24xx_clkout_setparent(struct clk *clk, struct clk *parent) /* calculate the MISCCR setting for the clock */ - if (parent == &clk_xtal) + if (parent == &clk_mpll) source = S3C2410_MISCCR_CLK0_MPLL; else if (parent == &clk_upll) source = S3C2410_MISCCR_CLK0_UPLL; -- GitLab From 17e78b0655da20f2fc2bbde3b8252dac07c82914 Mon Sep 17 00:00:00 2001 From: Yi Zou Date: Thu, 13 Aug 2009 14:09:58 +0000 Subject: [PATCH 1130/1342] ixgbe: Do not return 0 in ixgbe_fcoe_ddp() upon FCP_RSP in DDP completion We return the ddp->len in ixgbe_fcoe_ddp() to indicate the length of data that have been DDPed. However, it is possible that the length is 0, e.g., for SCSI READ, the FCP_RSP may come back w/ SCSI status 0x28 as Task Set Full with no FCP data for DDP. In ixgbe_fcoe_ddp(), we return 0 to indicate not passing DDPed packets to upper layer. Therefore in the case of ddp->len being 0 upon FCP_RSP, we do not want to return the 0 ddp->len as we want FCP_RSP to be always delivered to the upper layer. This patch fixes this bug by setting rc only if ddp->len is non-zero. Signed-off-by: Yi Zou Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_fcoe.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ixgbe/ixgbe_fcoe.c b/drivers/net/ixgbe/ixgbe_fcoe.c index fa9f24e2368..28cf104e36c 100644 --- a/drivers/net/ixgbe/ixgbe_fcoe.c +++ b/drivers/net/ixgbe/ixgbe_fcoe.c @@ -336,7 +336,7 @@ int ixgbe_fcoe_ddp(struct ixgbe_adapter *adapter, /* return 0 to bypass going to ULD for DDPed data */ if (fcstat == IXGBE_RXDADV_STAT_FCSTAT_DDP) rc = 0; - else + else if (ddp->len) rc = ddp->len; } -- GitLab From 8a62babfb87aa5911e87e0ce38381bdfdc4a2b83 Mon Sep 17 00:00:00 2001 From: Lucy Liu Date: Thu, 13 Aug 2009 14:09:38 +0000 Subject: [PATCH 1131/1342] ixgbe: Fix receive on real device when VLANs are configured Traffic received with a priority tag (VID = 0) and non-zero priority value was incorrectly handled by the VLAN packet code path due to a check on zero for the whole VLAN tag instead of just the VID. This patch masked out the priority field when checking the vlan tag for received VLAN packets. Signed-off-by: Lucy Liu Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_main.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index e3cb949b9aa..77b0381a2b5 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -492,12 +492,12 @@ static void ixgbe_receive_skb(struct ixgbe_q_vector *q_vector, skb_record_rx_queue(skb, ring->queue_index); if (!(adapter->flags & IXGBE_FLAG_IN_NETPOLL)) { - if (adapter->vlgrp && is_vlan && (tag != 0)) + if (adapter->vlgrp && is_vlan && (tag & VLAN_VID_MASK)) vlan_gro_receive(napi, adapter->vlgrp, tag, skb); else napi_gro_receive(napi, skb); } else { - if (adapter->vlgrp && is_vlan && (tag != 0)) + if (adapter->vlgrp && is_vlan && (tag & VLAN_VID_MASK)) vlan_hwaccel_rx(skb, adapter->vlgrp, tag); else netif_rx(skb); -- GitLab From d6647bdf98a0de19963de8d5d9698d469ed72097 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Tue, 21 Jul 2009 17:11:50 +0900 Subject: [PATCH 1132/1342] init: set nr_cpu_ids before setup_per_cpu_areas() nr_cpu_ids is dependent only on cpu_possible_map and setup_per_cpu_areas() already depends on cpu_possible_map and will use nr_cpu_ids. Initialize nr_cpu_ids before setting up percpu areas. Signed-off-by: Tejun Heo --- init/main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/init/main.c b/init/main.c index 2c5ade79eb8..2d9d6bdfe7c 100644 --- a/init/main.c +++ b/init/main.c @@ -584,8 +584,8 @@ asmlinkage void __init start_kernel(void) setup_arch(&command_line); mm_init_owner(&init_mm, &init_task); setup_command_line(command_line); - setup_per_cpu_areas(); setup_nr_cpu_ids(); + setup_per_cpu_areas(); smp_prepare_boot_cpu(); /* arch-specific boot-cpu hooks */ build_all_zonelists(); -- GitLab From 74d46d6b2d23d44d72c37df4c6a5d2e782f7b088 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Tue, 21 Jul 2009 17:11:50 +0900 Subject: [PATCH 1133/1342] percpu, sparc64: fix sparse possible cpu map handling percpu code has been assuming num_possible_cpus() == nr_cpu_ids which is incorrect if cpu_possible_map contains holes. This causes percpu code to access beyond allocated memories and vmalloc areas. On a sparc64 machine with cpus 0 and 2 (u60), this triggers the following warning or fails boot. WARNING: at /devel/tj/os/work/mm/vmalloc.c:106 vmap_page_range_noflush+0x1f0/0x240() Modules linked in: Call Trace: [00000000004b17d0] vmap_page_range_noflush+0x1f0/0x240 [00000000004b1840] map_vm_area+0x20/0x60 [00000000004b1950] __vmalloc_area_node+0xd0/0x160 [0000000000593434] deflate_init+0x14/0xe0 [0000000000583b94] __crypto_alloc_tfm+0xd4/0x1e0 [00000000005844f0] crypto_alloc_base+0x50/0xa0 [000000000058b898] alg_test_comp+0x18/0x80 [000000000058dad4] alg_test+0x54/0x180 [000000000058af00] cryptomgr_test+0x40/0x60 [0000000000473098] kthread+0x58/0x80 [000000000042b590] kernel_thread+0x30/0x60 [0000000000472fd0] kthreadd+0xf0/0x160 ---[ end trace 429b268a213317ba ]--- This patch fixes generic percpu functions and sparc64 setup_per_cpu_areas() so that they handle sparse cpu_possible_map properly. Please note that on x86, cpu_possible_map() doesn't contain holes and thus num_possible_cpus() == nr_cpu_ids and this patch doesn't cause any behavior difference. Signed-off-by: Tejun Heo Acked-by: David S. Miller Cc: Ingo Molnar --- arch/sparc/kernel/smp_64.c | 4 ++-- arch/x86/kernel/setup_percpu.c | 14 +++++++------- mm/percpu.c | 33 ++++++++++++++++++--------------- 3 files changed, 27 insertions(+), 24 deletions(-) diff --git a/arch/sparc/kernel/smp_64.c b/arch/sparc/kernel/smp_64.c index fa44eaf8d89..3691907a43b 100644 --- a/arch/sparc/kernel/smp_64.c +++ b/arch/sparc/kernel/smp_64.c @@ -1499,7 +1499,7 @@ void __init setup_per_cpu_areas(void) dyn_size = pcpur_size - static_size - PERCPU_MODULE_RESERVE; - ptrs_size = PFN_ALIGN(num_possible_cpus() * sizeof(pcpur_ptrs[0])); + ptrs_size = PFN_ALIGN(nr_cpu_ids * sizeof(pcpur_ptrs[0])); pcpur_ptrs = alloc_bootmem(ptrs_size); for_each_possible_cpu(cpu) { @@ -1514,7 +1514,7 @@ void __init setup_per_cpu_areas(void) /* allocate address and map */ vm.flags = VM_ALLOC; - vm.size = num_possible_cpus() * PCPU_CHUNK_SIZE; + vm.size = nr_cpu_ids * PCPU_CHUNK_SIZE; vm_area_register_early(&vm, PCPU_CHUNK_SIZE); for_each_possible_cpu(cpu) { diff --git a/arch/x86/kernel/setup_percpu.c b/arch/x86/kernel/setup_percpu.c index 29a3eef7cf4..07d81916f21 100644 --- a/arch/x86/kernel/setup_percpu.c +++ b/arch/x86/kernel/setup_percpu.c @@ -165,7 +165,7 @@ static ssize_t __init setup_pcpu_lpage(size_t static_size, bool chosen) if (!chosen) { size_t vm_size = VMALLOC_END - VMALLOC_START; - size_t tot_size = num_possible_cpus() * PMD_SIZE; + size_t tot_size = nr_cpu_ids * PMD_SIZE; /* on non-NUMA, embedding is better */ if (!pcpu_need_numa()) @@ -199,7 +199,7 @@ static ssize_t __init setup_pcpu_lpage(size_t static_size, bool chosen) dyn_size = pcpul_size - static_size - PERCPU_FIRST_CHUNK_RESERVE; /* allocate pointer array and alloc large pages */ - map_size = PFN_ALIGN(num_possible_cpus() * sizeof(pcpul_map[0])); + map_size = PFN_ALIGN(nr_cpu_ids * sizeof(pcpul_map[0])); pcpul_map = alloc_bootmem(map_size); for_each_possible_cpu(cpu) { @@ -228,7 +228,7 @@ static ssize_t __init setup_pcpu_lpage(size_t static_size, bool chosen) /* allocate address and map */ pcpul_vm.flags = VM_ALLOC; - pcpul_vm.size = num_possible_cpus() * PMD_SIZE; + pcpul_vm.size = nr_cpu_ids * PMD_SIZE; vm_area_register_early(&pcpul_vm, PMD_SIZE); for_each_possible_cpu(cpu) { @@ -250,8 +250,8 @@ static ssize_t __init setup_pcpu_lpage(size_t static_size, bool chosen) PMD_SIZE, pcpul_vm.addr, NULL); /* sort pcpul_map array for pcpu_lpage_remapped() */ - for (i = 0; i < num_possible_cpus() - 1; i++) - for (j = i + 1; j < num_possible_cpus(); j++) + for (i = 0; i < nr_cpu_ids - 1; i++) + for (j = i + 1; j < nr_cpu_ids; j++) if (pcpul_map[i].ptr > pcpul_map[j].ptr) { struct pcpul_ent tmp = pcpul_map[i]; pcpul_map[i] = pcpul_map[j]; @@ -288,7 +288,7 @@ void *pcpu_lpage_remapped(void *kaddr) { void *pmd_addr = (void *)((unsigned long)kaddr & PMD_MASK); unsigned long offset = (unsigned long)kaddr & ~PMD_MASK; - int left = 0, right = num_possible_cpus() - 1; + int left = 0, right = nr_cpu_ids - 1; int pos; /* pcpul in use at all? */ @@ -377,7 +377,7 @@ static ssize_t __init setup_pcpu_4k(size_t static_size) pcpu4k_nr_static_pages = PFN_UP(static_size); /* unaligned allocations can't be freed, round up to page size */ - pages_size = PFN_ALIGN(pcpu4k_nr_static_pages * num_possible_cpus() + pages_size = PFN_ALIGN(pcpu4k_nr_static_pages * nr_cpu_ids * sizeof(pcpu4k_pages[0])); pcpu4k_pages = alloc_bootmem(pages_size); diff --git a/mm/percpu.c b/mm/percpu.c index b70f2acd885..e0be1146f61 100644 --- a/mm/percpu.c +++ b/mm/percpu.c @@ -8,12 +8,12 @@ * * This is percpu allocator which can handle both static and dynamic * areas. Percpu areas are allocated in chunks in vmalloc area. Each - * chunk is consisted of num_possible_cpus() units and the first chunk - * is used for static percpu variables in the kernel image (special - * boot time alloc/init handling necessary as these areas need to be - * brought up before allocation services are running). Unit grows as - * necessary and all units grow or shrink in unison. When a chunk is - * filled up, another chunk is allocated. ie. in vmalloc area + * chunk is consisted of nr_cpu_ids units and the first chunk is used + * for static percpu variables in the kernel image (special boot time + * alloc/init handling necessary as these areas need to be brought up + * before allocation services are running). Unit grows as necessary + * and all units grow or shrink in unison. When a chunk is filled up, + * another chunk is allocated. ie. in vmalloc area * * c0 c1 c2 * ------------------- ------------------- ------------ @@ -558,7 +558,7 @@ static void pcpu_free_area(struct pcpu_chunk *chunk, int freeme) static void pcpu_unmap(struct pcpu_chunk *chunk, int page_start, int page_end, bool flush_tlb) { - unsigned int last = num_possible_cpus() - 1; + unsigned int last = nr_cpu_ids - 1; unsigned int cpu; /* unmap must not be done on immutable chunk */ @@ -643,7 +643,7 @@ static void pcpu_depopulate_chunk(struct pcpu_chunk *chunk, int off, int size, */ static int pcpu_map(struct pcpu_chunk *chunk, int page_start, int page_end) { - unsigned int last = num_possible_cpus() - 1; + unsigned int last = nr_cpu_ids - 1; unsigned int cpu; int err; @@ -1067,9 +1067,9 @@ size_t __init pcpu_setup_first_chunk(pcpu_get_page_fn_t get_page_fn, PFN_UP(size_sum)); pcpu_unit_size = pcpu_unit_pages << PAGE_SHIFT; - pcpu_chunk_size = num_possible_cpus() * pcpu_unit_size; + pcpu_chunk_size = nr_cpu_ids * pcpu_unit_size; pcpu_chunk_struct_size = sizeof(struct pcpu_chunk) - + num_possible_cpus() * pcpu_unit_pages * sizeof(struct page *); + + nr_cpu_ids * pcpu_unit_pages * sizeof(struct page *); if (dyn_size < 0) dyn_size = pcpu_unit_size - static_size - reserved_size; @@ -1248,7 +1248,7 @@ ssize_t __init pcpu_embed_first_chunk(size_t static_size, size_t reserved_size, } else pcpue_unit_size = max_t(size_t, pcpue_size, PCPU_MIN_UNIT_SIZE); - chunk_size = pcpue_unit_size * num_possible_cpus(); + chunk_size = pcpue_unit_size * nr_cpu_ids; pcpue_ptr = __alloc_bootmem_nopanic(chunk_size, PAGE_SIZE, __pa(MAX_DMA_ADDRESS)); @@ -1259,12 +1259,15 @@ ssize_t __init pcpu_embed_first_chunk(size_t static_size, size_t reserved_size, } /* return the leftover and copy */ - for_each_possible_cpu(cpu) { + for (cpu = 0; cpu < nr_cpu_ids; cpu++) { void *ptr = pcpue_ptr + cpu * pcpue_unit_size; - free_bootmem(__pa(ptr + pcpue_size), - pcpue_unit_size - pcpue_size); - memcpy(ptr, __per_cpu_load, static_size); + if (cpu_possible(cpu)) { + free_bootmem(__pa(ptr + pcpue_size), + pcpue_unit_size - pcpue_size); + memcpy(ptr, __per_cpu_load, static_size); + } else + free_bootmem(__pa(ptr), pcpue_unit_size); } /* we're ready, commit */ -- GitLab From 142d44b0dd6741a64a7bdbe029110e7c1dcf1d23 Mon Sep 17 00:00:00 2001 From: Amerigo Wang Date: Thu, 13 Aug 2009 02:00:13 -0400 Subject: [PATCH 1134/1342] percpu: use the right flag for get_vm_area() get_vm_area() only accepts VM_* flags, not GFP_*. And according to the doc of get_vm_area(), here should be VM_ALLOC. Signed-off-by: WANG Cong Acked-by: Tejun Heo Cc: Ingo Molnar --- mm/percpu.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/mm/percpu.c b/mm/percpu.c index e0be1146f61..5fe37842e0e 100644 --- a/mm/percpu.c +++ b/mm/percpu.c @@ -749,7 +749,7 @@ static struct pcpu_chunk *alloc_pcpu_chunk(void) chunk->map[chunk->map_used++] = pcpu_unit_size; chunk->page = chunk->page_ar; - chunk->vm = get_vm_area(pcpu_chunk_size, GFP_KERNEL); + chunk->vm = get_vm_area(pcpu_chunk_size, VM_ALLOC); if (!chunk->vm) { free_pcpu_chunk(chunk); return NULL; -- GitLab From 563abb4be1a79e7b64784d43beb9d0cacb1bad6f Mon Sep 17 00:00:00 2001 From: Valentin Longchamp Date: Tue, 11 Aug 2009 17:29:21 +0200 Subject: [PATCH 1135/1342] mx31moboard: invert sdhc ro signal sense Small confusion with our hardware engineer, the WP signal (RO) is active low on our boards, the signal has to inverted. This is a pretty straightforward patch, it could even go to -rc, but if not, then push it for 2.6.32. Signed-off-by: Valentin Longchamp Signed-off-by: Sascha Hauer --- arch/arm/mach-mx3/mx31moboard-devboard.c | 2 +- arch/arm/mach-mx3/mx31moboard-marxbot.c | 2 +- arch/arm/mach-mx3/mx31moboard.c | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm/mach-mx3/mx31moboard-devboard.c b/arch/arm/mach-mx3/mx31moboard-devboard.c index 4704405165a..b48581e7ded 100644 --- a/arch/arm/mach-mx3/mx31moboard-devboard.c +++ b/arch/arm/mach-mx3/mx31moboard-devboard.c @@ -63,7 +63,7 @@ static struct imxuart_platform_data uart_pdata = { static int devboard_sdhc2_get_ro(struct device *dev) { - return gpio_get_value(SDHC2_WP); + return !gpio_get_value(SDHC2_WP); } static int devboard_sdhc2_init(struct device *dev, irq_handler_t detect_irq, diff --git a/arch/arm/mach-mx3/mx31moboard-marxbot.c b/arch/arm/mach-mx3/mx31moboard-marxbot.c index 641c3d6153a..901fb0166c0 100644 --- a/arch/arm/mach-mx3/mx31moboard-marxbot.c +++ b/arch/arm/mach-mx3/mx31moboard-marxbot.c @@ -67,7 +67,7 @@ static unsigned int marxbot_pins[] = { static int marxbot_sdhc2_get_ro(struct device *dev) { - return gpio_get_value(SDHC2_WP); + return !gpio_get_value(SDHC2_WP); } static int marxbot_sdhc2_init(struct device *dev, irq_handler_t detect_irq, diff --git a/arch/arm/mach-mx3/mx31moboard.c b/arch/arm/mach-mx3/mx31moboard.c index a17f2e41160..2a2da4739ec 100644 --- a/arch/arm/mach-mx3/mx31moboard.c +++ b/arch/arm/mach-mx3/mx31moboard.c @@ -94,7 +94,7 @@ static struct imxi2c_platform_data moboard_i2c1_pdata = { static int moboard_sdhc1_get_ro(struct device *dev) { - return gpio_get_value(SDHC1_WP); + return !gpio_get_value(SDHC1_WP); } static int moboard_sdhc1_init(struct device *dev, irq_handler_t detect_irq, -- GitLab From d7e623da1a757fbd8c117fa29190ca8bef14dab3 Mon Sep 17 00:00:00 2001 From: Steven Whitehouse Date: Tue, 11 Aug 2009 11:20:11 +0100 Subject: [PATCH 1136/1342] GFS2: Fix permissions on "recover" file Although this file is only ever written and not read by userspace, it seems that the utils are opening this file O_RDWR, so we need to allow that. Also fixes the whitespace which seemed to be broken. Signed-off-by: Steven Whitehouse Cc: David Teigland --- fs/gfs2/sys.c | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) diff --git a/fs/gfs2/sys.c b/fs/gfs2/sys.c index 23419dc3027..a7cbfbd340c 100644 --- a/fs/gfs2/sys.c +++ b/fs/gfs2/sys.c @@ -386,16 +386,16 @@ static ssize_t jid_show(struct gfs2_sbd *sdp, char *buf) #define GDLM_ATTR(_name,_mode,_show,_store) \ static struct gfs2_attr gdlm_attr_##_name = __ATTR(_name,_mode,_show,_store) -GDLM_ATTR(proto_name, 0444, proto_name_show, NULL); -GDLM_ATTR(block, 0644, block_show, block_store); -GDLM_ATTR(withdraw, 0644, withdraw_show, withdraw_store); -GDLM_ATTR(id, 0444, lkid_show, NULL); -GDLM_ATTR(jid, 0444, jid_show, NULL); -GDLM_ATTR(first, 0444, lkfirst_show, NULL); -GDLM_ATTR(first_done, 0444, first_done_show, NULL); -GDLM_ATTR(recover, 0200, NULL, recover_store); -GDLM_ATTR(recover_done, 0444, recover_done_show, NULL); -GDLM_ATTR(recover_status, 0444, recover_status_show, NULL); +GDLM_ATTR(proto_name, 0444, proto_name_show, NULL); +GDLM_ATTR(block, 0644, block_show, block_store); +GDLM_ATTR(withdraw, 0644, withdraw_show, withdraw_store); +GDLM_ATTR(id, 0444, lkid_show, NULL); +GDLM_ATTR(jid, 0444, jid_show, NULL); +GDLM_ATTR(first, 0444, lkfirst_show, NULL); +GDLM_ATTR(first_done, 0444, first_done_show, NULL); +GDLM_ATTR(recover, 0600, NULL, recover_store); +GDLM_ATTR(recover_done, 0444, recover_done_show, NULL); +GDLM_ATTR(recover_status, 0444, recover_status_show, NULL); static struct attribute *lock_module_attrs[] = { &gdlm_attr_proto_name.attr, -- GitLab From 6b26dead3ce97d016b57724b01974d5ca5c84bd5 Mon Sep 17 00:00:00 2001 From: Pavel Roskin Date: Tue, 4 Aug 2009 17:48:16 -0400 Subject: [PATCH 1137/1342] rt2x00: fix memory corruption in rf cache, add a sanity check Change rt2x00_rf_read() and rt2x00_rf_write() to subtract 1 from the rf register number. This is needed because the rf registers are enumerated starting with one. The size of the rf register cache is just enough to hold all registers, so writing to the highest register was corrupting memory. Add a check to make sure that the rf register number is valid. Signed-off-by: Pavel Roskin Cc: stable@kernel.org Acked-by: Ivo van Doorn Signed-off-by: John W. Linville --- drivers/net/wireless/rt2x00/rt2x00.h | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/net/wireless/rt2x00/rt2x00.h b/drivers/net/wireless/rt2x00/rt2x00.h index a498dde024e..49c9e2c1433 100644 --- a/drivers/net/wireless/rt2x00/rt2x00.h +++ b/drivers/net/wireless/rt2x00/rt2x00.h @@ -849,13 +849,15 @@ struct rt2x00_dev { static inline void rt2x00_rf_read(struct rt2x00_dev *rt2x00dev, const unsigned int word, u32 *data) { - *data = rt2x00dev->rf[word]; + BUG_ON(word < 1 || word > rt2x00dev->ops->rf_size / sizeof(u32)); + *data = rt2x00dev->rf[word - 1]; } static inline void rt2x00_rf_write(struct rt2x00_dev *rt2x00dev, const unsigned int word, u32 data) { - rt2x00dev->rf[word] = data; + BUG_ON(word < 1 || word > rt2x00dev->ops->rf_size / sizeof(u32)); + rt2x00dev->rf[word - 1] = data; } /* -- GitLab From 388ce4beb7135722c584b0af18f215e3ec657adf Mon Sep 17 00:00:00 2001 From: "Kashyap, Desai" Date: Fri, 14 Aug 2009 15:01:35 +0530 Subject: [PATCH 1138/1342] [SCSI] mpt2sas: fix config request and diag reset deadlock Moving the setting and clearing of the mutex's to _config_request. There was a mutex deadlock when diag reset is called from inside _config_request, so diag reset was moved to outside the mutexs. Signed-off-by: James Bottomley --- drivers/scsi/mpt2sas/mpt2sas_config.c | 85 +++++++-------------------- 1 file changed, 20 insertions(+), 65 deletions(-) diff --git a/drivers/scsi/mpt2sas/mpt2sas_config.c b/drivers/scsi/mpt2sas/mpt2sas_config.c index 1c6658c6023..6ddee161beb 100644 --- a/drivers/scsi/mpt2sas/mpt2sas_config.c +++ b/drivers/scsi/mpt2sas/mpt2sas_config.c @@ -236,12 +236,14 @@ _config_request(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigRequest_t Mpi2ConfigRequest_t *config_request; int r; u8 retry_count; - u8 issue_reset; + u8 issue_host_reset = 0; u16 wait_state_count; + mutex_lock(&ioc->config_cmds.mutex); if (ioc->config_cmds.status != MPT2_CMD_NOT_USED) { printk(MPT2SAS_ERR_FMT "%s: config_cmd in use\n", ioc->name, __func__); + mutex_unlock(&ioc->config_cmds.mutex); return -EAGAIN; } retry_count = 0; @@ -260,8 +262,8 @@ _config_request(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigRequest_t printk(MPT2SAS_ERR_FMT "%s: failed due to ioc not operational\n", ioc->name, __func__); - ioc->config_cmds.status = MPT2_CMD_NOT_USED; - return -EFAULT; + r = -EFAULT; + goto out; } ssleep(1); ioc_state = mpt2sas_base_get_iocstate(ioc, 1); @@ -277,8 +279,8 @@ _config_request(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigRequest_t if (!smid) { printk(MPT2SAS_ERR_FMT "%s: failed obtaining a smid\n", ioc->name, __func__); - ioc->config_cmds.status = MPT2_CMD_NOT_USED; - return -EAGAIN; + r = -EAGAIN; + goto out; } r = 0; @@ -298,9 +300,15 @@ _config_request(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigRequest_t ioc->name, __func__); _debug_dump_mf(mpi_request, sizeof(Mpi2ConfigRequest_t)/4); - if (!(ioc->config_cmds.status & MPT2_CMD_RESET)) - issue_reset = 1; - goto issue_host_reset; + retry_count++; + if (ioc->config_cmds.smid == smid) + mpt2sas_base_free_smid(ioc, smid); + if ((ioc->shost_recovery) || + (ioc->config_cmds.status & MPT2_CMD_RESET)) + goto retry_config; + issue_host_reset = 1; + r = -EFAULT; + goto out; } if (ioc->config_cmds.status & MPT2_CMD_REPLY_VALID) memcpy(mpi_reply, ioc->config_cmds.reply, @@ -308,21 +316,13 @@ _config_request(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigRequest_t if (retry_count) printk(MPT2SAS_INFO_FMT "%s: retry completed!!\n", ioc->name, __func__); +out: ioc->config_cmds.status = MPT2_CMD_NOT_USED; - return r; - - issue_host_reset: - if (issue_reset) + mutex_unlock(&ioc->config_cmds.mutex); + if (issue_host_reset) mpt2sas_base_hard_reset_handler(ioc, CAN_SLEEP, FORCE_BIG_HAMMER); - ioc->config_cmds.status = MPT2_CMD_NOT_USED; - if (!retry_count) { - printk(MPT2SAS_INFO_FMT "%s: attempting retry\n", - ioc->name, __func__); - retry_count++; - goto retry_config; - } - return -EFAULT; + return r; } /** @@ -381,7 +381,6 @@ mpt2sas_config_get_manufacturing_pg0(struct MPT2SAS_ADAPTER *ioc, int r; struct config_request mem; - mutex_lock(&ioc->config_cmds.mutex); memset(config_page, 0, sizeof(Mpi2ManufacturingPage0_t)); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -423,7 +422,6 @@ mpt2sas_config_get_manufacturing_pg0(struct MPT2SAS_ADAPTER *ioc, _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -444,7 +442,6 @@ mpt2sas_config_get_bios_pg2(struct MPT2SAS_ADAPTER *ioc, int r; struct config_request mem; - mutex_lock(&ioc->config_cmds.mutex); memset(config_page, 0, sizeof(Mpi2BiosPage2_t)); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -486,7 +483,6 @@ mpt2sas_config_get_bios_pg2(struct MPT2SAS_ADAPTER *ioc, _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -507,7 +503,6 @@ mpt2sas_config_get_bios_pg3(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t int r; struct config_request mem; - mutex_lock(&ioc->config_cmds.mutex); memset(config_page, 0, sizeof(Mpi2BiosPage3_t)); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -549,7 +544,6 @@ mpt2sas_config_get_bios_pg3(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -570,7 +564,6 @@ mpt2sas_config_get_iounit_pg0(struct MPT2SAS_ADAPTER *ioc, int r; struct config_request mem; - mutex_lock(&ioc->config_cmds.mutex); memset(config_page, 0, sizeof(Mpi2IOUnitPage0_t)); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -612,7 +605,6 @@ mpt2sas_config_get_iounit_pg0(struct MPT2SAS_ADAPTER *ioc, _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -633,7 +625,6 @@ mpt2sas_config_get_iounit_pg1(struct MPT2SAS_ADAPTER *ioc, int r; struct config_request mem; - mutex_lock(&ioc->config_cmds.mutex); memset(config_page, 0, sizeof(Mpi2IOUnitPage1_t)); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -675,7 +666,6 @@ mpt2sas_config_get_iounit_pg1(struct MPT2SAS_ADAPTER *ioc, _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -696,7 +686,6 @@ mpt2sas_config_set_iounit_pg1(struct MPT2SAS_ADAPTER *ioc, int r; struct config_request mem; - mutex_lock(&ioc->config_cmds.mutex); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; mpi_request.Action = MPI2_CONFIG_ACTION_PAGE_HEADER; @@ -738,7 +727,6 @@ mpt2sas_config_set_iounit_pg1(struct MPT2SAS_ADAPTER *ioc, _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -759,7 +747,6 @@ mpt2sas_config_get_ioc_pg8(struct MPT2SAS_ADAPTER *ioc, int r; struct config_request mem; - mutex_lock(&ioc->config_cmds.mutex); memset(config_page, 0, sizeof(Mpi2IOCPage8_t)); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -801,7 +788,6 @@ mpt2sas_config_get_ioc_pg8(struct MPT2SAS_ADAPTER *ioc, _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -824,7 +810,6 @@ mpt2sas_config_get_sas_device_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t int r; struct config_request mem; - mutex_lock(&ioc->config_cmds.mutex); memset(config_page, 0, sizeof(Mpi2SasDevicePage0_t)); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -869,7 +854,6 @@ mpt2sas_config_get_sas_device_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -892,7 +876,6 @@ mpt2sas_config_get_sas_device_pg1(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t int r; struct config_request mem; - mutex_lock(&ioc->config_cmds.mutex); memset(config_page, 0, sizeof(Mpi2SasDevicePage1_t)); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -937,7 +920,6 @@ mpt2sas_config_get_sas_device_pg1(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -959,7 +941,6 @@ mpt2sas_config_get_number_hba_phys(struct MPT2SAS_ADAPTER *ioc, u8 *num_phys) Mpi2ConfigReply_t mpi_reply; Mpi2SasIOUnitPage0_t config_page; - mutex_lock(&ioc->config_cmds.mutex); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; mpi_request.Action = MPI2_CONFIG_ACTION_PAGE_HEADER; @@ -1008,7 +989,6 @@ mpt2sas_config_get_number_hba_phys(struct MPT2SAS_ADAPTER *ioc, u8 *num_phys) _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -1032,8 +1012,6 @@ mpt2sas_config_get_sas_iounit_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t Mpi2ConfigRequest_t mpi_request; int r; struct config_request mem; - - mutex_lock(&ioc->config_cmds.mutex); memset(config_page, 0, sz); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -1076,7 +1054,6 @@ mpt2sas_config_get_sas_iounit_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -1101,7 +1078,6 @@ mpt2sas_config_get_sas_iounit_pg1(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t int r; struct config_request mem; - mutex_lock(&ioc->config_cmds.mutex); memset(config_page, 0, sz); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -1144,7 +1120,6 @@ mpt2sas_config_get_sas_iounit_pg1(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -1167,7 +1142,6 @@ mpt2sas_config_get_expander_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t int r; struct config_request mem; - mutex_lock(&ioc->config_cmds.mutex); memset(config_page, 0, sizeof(Mpi2ExpanderPage0_t)); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -1212,7 +1186,6 @@ mpt2sas_config_get_expander_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -1236,7 +1209,6 @@ mpt2sas_config_get_expander_pg1(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t int r; struct config_request mem; - mutex_lock(&ioc->config_cmds.mutex); memset(config_page, 0, sizeof(Mpi2ExpanderPage1_t)); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -1283,7 +1255,6 @@ mpt2sas_config_get_expander_pg1(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -1306,7 +1277,6 @@ mpt2sas_config_get_enclosure_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t int r; struct config_request mem; - mutex_lock(&ioc->config_cmds.mutex); memset(config_page, 0, sizeof(Mpi2SasEnclosurePage0_t)); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -1351,7 +1321,6 @@ mpt2sas_config_get_enclosure_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -1373,7 +1342,6 @@ mpt2sas_config_get_phy_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t int r; struct config_request mem; - mutex_lock(&ioc->config_cmds.mutex); memset(config_page, 0, sizeof(Mpi2SasPhyPage0_t)); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -1419,7 +1387,6 @@ mpt2sas_config_get_phy_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -1441,7 +1408,6 @@ mpt2sas_config_get_phy_pg1(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t int r; struct config_request mem; - mutex_lock(&ioc->config_cmds.mutex); memset(config_page, 0, sizeof(Mpi2SasPhyPage1_t)); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -1487,7 +1453,6 @@ mpt2sas_config_get_phy_pg1(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -1511,7 +1476,6 @@ mpt2sas_config_get_raid_volume_pg1(struct MPT2SAS_ADAPTER *ioc, int r; struct config_request mem; - mutex_lock(&ioc->config_cmds.mutex); memset(config_page, 0, sizeof(Mpi2RaidVolPage1_t)); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -1554,7 +1518,6 @@ mpt2sas_config_get_raid_volume_pg1(struct MPT2SAS_ADAPTER *ioc, _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -1578,7 +1541,6 @@ mpt2sas_config_get_number_pds(struct MPT2SAS_ADAPTER *ioc, u16 handle, struct config_request mem; u16 ioc_status; - mutex_lock(&ioc->config_cmds.mutex); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); *num_pds = 0; mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -1626,7 +1588,6 @@ mpt2sas_config_get_number_pds(struct MPT2SAS_ADAPTER *ioc, u16 handle, _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -1651,7 +1612,6 @@ mpt2sas_config_get_raid_volume_pg0(struct MPT2SAS_ADAPTER *ioc, int r; struct config_request mem; - mutex_lock(&ioc->config_cmds.mutex); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); memset(config_page, 0, sz); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -1693,7 +1653,6 @@ mpt2sas_config_get_raid_volume_pg0(struct MPT2SAS_ADAPTER *ioc, _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -1717,7 +1676,6 @@ mpt2sas_config_get_phys_disk_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t int r; struct config_request mem; - mutex_lock(&ioc->config_cmds.mutex); memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); memset(config_page, 0, sizeof(Mpi2RaidPhysDiskPage0_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -1760,7 +1718,6 @@ mpt2sas_config_get_phys_disk_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } @@ -1784,7 +1741,6 @@ mpt2sas_config_get_volume_handle(struct MPT2SAS_ADAPTER *ioc, u16 pd_handle, struct config_request mem; u16 ioc_status; - mutex_lock(&ioc->config_cmds.mutex); *volume_handle = 0; memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t)); mpi_request.Function = MPI2_FUNCTION_CONFIG; @@ -1848,7 +1804,6 @@ mpt2sas_config_get_volume_handle(struct MPT2SAS_ADAPTER *ioc, u16 pd_handle, _config_free_config_dma_memory(ioc, &mem); out: - mutex_unlock(&ioc->config_cmds.mutex); return r; } -- GitLab From 0527a1a8440a20b3d0fd1d0c9e75a6f38a9d5315 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Fri, 14 Aug 2009 02:09:56 +0000 Subject: [PATCH 1139/1342] via-velocity: Fix test of mii_status bit VELOCITY_DUPLEX_FULL Test whether VELOCITY_DUPLEX_FULL bit is set in mii_status. Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/via-velocity.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/via-velocity.c b/drivers/net/via-velocity.c index 3ba35956327..cee08a1e497 100644 --- a/drivers/net/via-velocity.c +++ b/drivers/net/via-velocity.c @@ -1778,7 +1778,7 @@ static void velocity_error(struct velocity_info *vptr, int status) * mode */ if (vptr->rev_id < REV_ID_VT3216_A0) { - if (vptr->mii_status | VELOCITY_DUPLEX_FULL) + if (vptr->mii_status & VELOCITY_DUPLEX_FULL) BYTE_REG_BITS_ON(TCR_TB2BDIS, ®s->TCR); else BYTE_REG_BITS_OFF(TCR_TB2BDIS, ®s->TCR); -- GitLab From 22580f894ac190c46beebb5c3172e450a2318f79 Mon Sep 17 00:00:00 2001 From: Dongdong Deng Date: Thu, 13 Aug 2009 19:12:31 +0000 Subject: [PATCH 1140/1342] drivers/net: fixed drivers that support netpoll use ndo_start_xmit() The NETPOLL API requires that interrupts remain disabled in netpoll_send_skb(). The use of spin_lock_irq() and spin_unlock_irq() in the NETPOLL API callbacks causes the interrupts to get enabled and can lead to kernel instability. The solution is to use spin_lock_irqsave() and spin_unlock_restore() to prevent the irqs from getting enabled while in netpoll_send_skb(). Call trace: netpoll_send_skb() { -> local_irq_save(flags) ---> dev->ndo_start_xmit(skb, dev) ---> spin_lock_irq() ---> spin_unlock_irq() *******here would enable the interrupt. ... -> local_irq_restore(flags) } Signed-off-by: Dongdong Deng Signed-off-by: Jason Wessel Acked-by: Bruce Ashfield Acked-by: Matt Mackall Signed-off-by: David S. Miller --- drivers/net/b44.c | 5 +++-- drivers/net/tulip/tulip_core.c | 5 +++-- drivers/net/ucc_geth.c | 5 +++-- drivers/net/via-rhine.c | 5 +++-- 4 files changed, 12 insertions(+), 8 deletions(-) diff --git a/drivers/net/b44.c b/drivers/net/b44.c index 36d4d377ec2..bafca672ea7 100644 --- a/drivers/net/b44.c +++ b/drivers/net/b44.c @@ -952,9 +952,10 @@ static int b44_start_xmit(struct sk_buff *skb, struct net_device *dev) int rc = NETDEV_TX_OK; dma_addr_t mapping; u32 len, entry, ctrl; + unsigned long flags; len = skb->len; - spin_lock_irq(&bp->lock); + spin_lock_irqsave(&bp->lock, flags); /* This is a hard error, log it. */ if (unlikely(TX_BUFFS_AVAIL(bp) < 1)) { @@ -1027,7 +1028,7 @@ static int b44_start_xmit(struct sk_buff *skb, struct net_device *dev) dev->trans_start = jiffies; out_unlock: - spin_unlock_irq(&bp->lock); + spin_unlock_irqrestore(&bp->lock, flags); return rc; diff --git a/drivers/net/tulip/tulip_core.c b/drivers/net/tulip/tulip_core.c index 99a63649f4f..4cf9a658875 100644 --- a/drivers/net/tulip/tulip_core.c +++ b/drivers/net/tulip/tulip_core.c @@ -652,8 +652,9 @@ tulip_start_xmit(struct sk_buff *skb, struct net_device *dev) int entry; u32 flag; dma_addr_t mapping; + unsigned long flags; - spin_lock_irq(&tp->lock); + spin_lock_irqsave(&tp->lock, flags); /* Calculate the next Tx descriptor entry. */ entry = tp->cur_tx % TX_RING_SIZE; @@ -688,7 +689,7 @@ tulip_start_xmit(struct sk_buff *skb, struct net_device *dev) /* Trigger an immediate transmit demand. */ iowrite32(0, tp->base_addr + CSR1); - spin_unlock_irq(&tp->lock); + spin_unlock_irqrestore(&tp->lock, flags); dev->trans_start = jiffies; diff --git a/drivers/net/ucc_geth.c b/drivers/net/ucc_geth.c index 3b957e6412e..8a7b8c7bd78 100644 --- a/drivers/net/ucc_geth.c +++ b/drivers/net/ucc_geth.c @@ -3111,10 +3111,11 @@ static int ucc_geth_start_xmit(struct sk_buff *skb, struct net_device *dev) u8 __iomem *bd; /* BD pointer */ u32 bd_status; u8 txQ = 0; + unsigned long flags; ugeth_vdbg("%s: IN", __func__); - spin_lock_irq(&ugeth->lock); + spin_lock_irqsave(&ugeth->lock, flags); dev->stats.tx_bytes += skb->len; @@ -3171,7 +3172,7 @@ static int ucc_geth_start_xmit(struct sk_buff *skb, struct net_device *dev) uccf = ugeth->uccf; out_be16(uccf->p_utodr, UCC_FAST_TOD); #endif - spin_unlock_irq(&ugeth->lock); + spin_unlock_irqrestore(&ugeth->lock, flags); return 0; } diff --git a/drivers/net/via-rhine.c b/drivers/net/via-rhine.c index 88c30a58b4b..934f7671650 100644 --- a/drivers/net/via-rhine.c +++ b/drivers/net/via-rhine.c @@ -1218,6 +1218,7 @@ static int rhine_start_tx(struct sk_buff *skb, struct net_device *dev) struct rhine_private *rp = netdev_priv(dev); void __iomem *ioaddr = rp->base; unsigned entry; + unsigned long flags; /* Caution: the write order is important here, set the field with the "ownership" bits last. */ @@ -1261,7 +1262,7 @@ static int rhine_start_tx(struct sk_buff *skb, struct net_device *dev) cpu_to_le32(TXDESC | (skb->len >= ETH_ZLEN ? skb->len : ETH_ZLEN)); /* lock eth irq */ - spin_lock_irq(&rp->lock); + spin_lock_irqsave(&rp->lock, flags); wmb(); rp->tx_ring[entry].tx_status = cpu_to_le32(DescOwn); wmb(); @@ -1280,7 +1281,7 @@ static int rhine_start_tx(struct sk_buff *skb, struct net_device *dev) dev->trans_start = jiffies; - spin_unlock_irq(&rp->lock); + spin_unlock_irqrestore(&rp->lock, flags); if (debug > 4) { printk(KERN_DEBUG "%s: Transmit frame #%d queued in slot %d.\n", -- GitLab From 7c1d15d736687057f4dc6e51fbf44b6f6e4320cb Mon Sep 17 00:00:00 2001 From: Petko Manolov Date: Fri, 14 Aug 2009 06:40:48 +0000 Subject: [PATCH 1141/1342] pegasus: Add new device ID. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Add new definition to 'pegasus.h' for support Japanese IO DATA "ETX-US2" USB Ethernet Adapter. PEGASUS_DEV( $B!H(BIO DATA USB ETX-US2$B!I(B, VENDOR_IODATA, 0x092a, DEFAULT_GPIO_RESET | PEGASUS_II ) Signed-off-by: David S. Miller --- drivers/net/usb/pegasus.h | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/net/usb/pegasus.h b/drivers/net/usb/pegasus.h index c7467823cd1..f968c834ff6 100644 --- a/drivers/net/usb/pegasus.h +++ b/drivers/net/usb/pegasus.h @@ -250,6 +250,8 @@ PEGASUS_DEV( "IO DATA USB ET/TX", VENDOR_IODATA, 0x0904, DEFAULT_GPIO_RESET ) PEGASUS_DEV( "IO DATA USB ET/TX-S", VENDOR_IODATA, 0x0913, DEFAULT_GPIO_RESET | PEGASUS_II ) +PEGASUS_DEV( "IO DATA USB ETX-US2", VENDOR_IODATA, 0x092a, + DEFAULT_GPIO_RESET | PEGASUS_II ) PEGASUS_DEV( "Kingston KNU101TX Ethernet", VENDOR_KINGSTON, 0x000a, DEFAULT_GPIO_RESET) PEGASUS_DEV( "LANEED USB Ethernet LD-USB/TX", VENDOR_LANEED, 0x4002, -- GitLab From 8cdb045632e5ee22854538619ac6f150eb0a4894 Mon Sep 17 00:00:00 2001 From: Tom Goff Date: Fri, 14 Aug 2009 16:33:56 -0700 Subject: [PATCH 1142/1342] gre: Fix MTU calculation for bound GRE tunnels The GRE header length should be subtracted when the tunnel MTU is calculated. This just corrects for the associativity change introduced by commit 42aa916265d740d66ac1f17290366e9494c884c2 ("gre: Move MTU setting out of ipgre_tunnel_bind_dev"). Signed-off-by: Tom Goff Signed-off-by: David S. Miller --- net/ipv4/ip_gre.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/ipv4/ip_gre.c b/net/ipv4/ip_gre.c index cb4a0f4bd5e..82c11dd10a6 100644 --- a/net/ipv4/ip_gre.c +++ b/net/ipv4/ip_gre.c @@ -951,7 +951,7 @@ static int ipgre_tunnel_bind_dev(struct net_device *dev) addend += 4; } dev->needed_headroom = addend + hlen; - mtu -= dev->hard_header_len - addend; + mtu -= dev->hard_header_len + addend; if (mtu < 68) mtu = 68; -- GitLab From 616b8434688aa08bd6f019cc60c8dfe121e9e5ae Mon Sep 17 00:00:00 2001 From: Jerome Glisse Date: Thu, 6 Aug 2009 17:47:24 +0200 Subject: [PATCH 1143/1342] drm/radeon/kms: Add specific rs690 authorized register table rs690 is r3xx 3D engine with AVIVO modesetting so we need to allow AVIVO register for vline synchronization. This add a specific table to rs690 to handle that. Thanks to Marc (marvin24) for debugging this and kudos to Andre (taiu1) for spotting the origin of the bugs. Signed-off-by: Jerome Glisse Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_asic.h | 3 +- drivers/gpu/drm/radeon/rs690.c | 65 ++++++++++++++++++++++++++++ 2 files changed, 67 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/radeon/radeon_asic.h b/drivers/gpu/drm/radeon/radeon_asic.h index 9a75876e0c3..c0ae2d92325 100644 --- a/drivers/gpu/drm/radeon/radeon_asic.h +++ b/drivers/gpu/drm/radeon/radeon_asic.h @@ -308,6 +308,7 @@ static struct radeon_asic rs600_asic = { /* * rs690,rs740 */ +int rs690_init(struct radeon_device *rdev); void rs690_errata(struct radeon_device *rdev); void rs690_vram_info(struct radeon_device *rdev); int rs690_mc_init(struct radeon_device *rdev); @@ -316,7 +317,7 @@ uint32_t rs690_mc_rreg(struct radeon_device *rdev, uint32_t reg); void rs690_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v); void rs690_bandwidth_update(struct radeon_device *rdev); static struct radeon_asic rs690_asic = { - .init = &r300_init, + .init = &rs690_init, .errata = &rs690_errata, .vram_info = &rs690_vram_info, .gpu_reset = &r300_gpu_reset, diff --git a/drivers/gpu/drm/radeon/rs690.c b/drivers/gpu/drm/radeon/rs690.c index 839595b0072..bc6b7c5339b 100644 --- a/drivers/gpu/drm/radeon/rs690.c +++ b/drivers/gpu/drm/radeon/rs690.c @@ -652,3 +652,68 @@ void rs690_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) WREG32(RS690_MC_DATA, v); WREG32(RS690_MC_INDEX, RS690_MC_INDEX_WR_ACK); } + +static const unsigned rs690_reg_safe_bm[219] = { + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0x17FF1FFF,0xFFFFFFFC,0xFFFFFFFF,0xFF30FFBF, + 0xFFFFFFF8,0xC3E6FFFF,0xFFFFF6DF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFF03F, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFEFCE,0xF00EBFFF,0x007C0000, + 0xF0000078,0xFF000009,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFF7FF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFC78,0xFFFFFFFF,0xFFFFFFFE,0xFFFFFFFF, + 0x38FF8F50,0xFFF88082,0xF000000C,0xFAE009FF, + 0x0000FFFF,0xFFFFFFFF,0xFFFFFFFF,0x00000000, + 0x00000000,0x0000C100,0x00000000,0x00000000, + 0x00000000,0x00000000,0x00000000,0x00000000, + 0x00000000,0xFFFF0000,0xFFFFFFFF,0xFF80FFFF, + 0x00000000,0x00000000,0x00000000,0x00000000, + 0x0003FC01,0xFFFFFFF8,0xFE800B19,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, +}; + +int rs690_init(struct radeon_device *rdev) +{ + rdev->config.r300.reg_safe_bm = rs690_reg_safe_bm; + rdev->config.r300.reg_safe_bm_size = ARRAY_SIZE(rs690_reg_safe_bm); + return 0; +} -- GitLab From ebb177d2afb8532a8a316489aed545ed0c170802 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Sat, 15 Aug 2009 12:25:08 +1000 Subject: [PATCH 1144/1342] drm/edid: fixup detailed timings like the X server. this syncs the versioning check with the code the X server uses. Reported-by: Anssi Hannula Signed-off-by: Dave Airlie --- drivers/gpu/drm/drm_edid.c | 72 ++++++++++++++++++-------------------- 1 file changed, 34 insertions(+), 38 deletions(-) diff --git a/drivers/gpu/drm/drm_edid.c b/drivers/gpu/drm/drm_edid.c index 80cc6d06d61..7f2728bbc16 100644 --- a/drivers/gpu/drm/drm_edid.c +++ b/drivers/gpu/drm/drm_edid.c @@ -502,12 +502,40 @@ static int add_detailed_info(struct drm_connector *connector, struct detailed_non_pixel *data = &timing->data.other_data; struct drm_display_mode *newmode; - /* EDID up to and including 1.2 may put monitor info here */ - if (edid->version == 1 && edid->revision < 3) - continue; - - /* Detailed mode timing */ - if (timing->pixel_clock) { + /* X server check is version 1.1 or higher */ + if (edid->version == 1 && edid->revision >= 1 && + !timing->pixel_clock) { + /* Other timing or info */ + switch (data->type) { + case EDID_DETAIL_MONITOR_SERIAL: + break; + case EDID_DETAIL_MONITOR_STRING: + break; + case EDID_DETAIL_MONITOR_RANGE: + /* Get monitor range data */ + break; + case EDID_DETAIL_MONITOR_NAME: + break; + case EDID_DETAIL_MONITOR_CPDATA: + break; + case EDID_DETAIL_STD_MODES: + /* Five modes per detailed section */ + for (j = 0; j < 5; i++) { + struct std_timing *std; + struct drm_display_mode *newmode; + + std = &data->data.timings[j]; + newmode = drm_mode_std(dev, std); + if (newmode) { + drm_mode_probed_add(connector, newmode); + modes++; + } + } + break; + default: + break; + } + } else { newmode = drm_mode_detailed(dev, edid, timing, quirks); if (!newmode) continue; @@ -518,38 +546,6 @@ static int add_detailed_info(struct drm_connector *connector, drm_mode_probed_add(connector, newmode); modes++; - continue; - } - - /* Other timing or info */ - switch (data->type) { - case EDID_DETAIL_MONITOR_SERIAL: - break; - case EDID_DETAIL_MONITOR_STRING: - break; - case EDID_DETAIL_MONITOR_RANGE: - /* Get monitor range data */ - break; - case EDID_DETAIL_MONITOR_NAME: - break; - case EDID_DETAIL_MONITOR_CPDATA: - break; - case EDID_DETAIL_STD_MODES: - /* Five modes per detailed section */ - for (j = 0; j < 5; i++) { - struct std_timing *std; - struct drm_display_mode *newmode; - - std = &data->data.timings[j]; - newmode = drm_mode_std(dev, std); - if (newmode) { - drm_mode_probed_add(connector, newmode); - modes++; - } - } - break; - default: - break; } } -- GitLab From 21bc1f024d0d4ea43fc0f2a43504e759261c7b18 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Sat, 15 Aug 2009 02:53:16 +0000 Subject: [PATCH 1145/1342] sh: skip disabled LCDC channels This patch updates the SuperH Mobile LCDC driver to skip over disabled channels. Without this patch suspend-to-ram operation will crash if deferred io is enabled. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt --- drivers/video/sh_mobile_lcdcfb.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/video/sh_mobile_lcdcfb.c b/drivers/video/sh_mobile_lcdcfb.c index 8f24564f77b..07f22b62563 100644 --- a/drivers/video/sh_mobile_lcdcfb.c +++ b/drivers/video/sh_mobile_lcdcfb.c @@ -481,6 +481,9 @@ static int sh_mobile_lcdc_start(struct sh_mobile_lcdc_priv *priv) /* tell the board code to enable the panel */ for (k = 0; k < ARRAY_SIZE(priv->ch); k++) { ch = &priv->ch[k]; + if (!ch->enabled) + continue; + board_cfg = &ch->cfg.board_cfg; if (board_cfg->display_on) board_cfg->display_on(board_cfg->board_data); @@ -498,6 +501,8 @@ static void sh_mobile_lcdc_stop(struct sh_mobile_lcdc_priv *priv) /* clean up deferred io and ask board code to disable panel */ for (k = 0; k < ARRAY_SIZE(priv->ch); k++) { ch = &priv->ch[k]; + if (!ch->enabled) + continue; /* deferred io mode: * flush frame, and wait for frame end interrupt -- GitLab From f6431732f128a241b149c0aa85dfec852455ebf9 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Sat, 15 Aug 2009 02:53:25 +0000 Subject: [PATCH 1146/1342] sh: CMT suspend/resume This patch updates the SuperH CMT driver with suspend and resume callbacks for the suspend-to-ram case. This patch stops the CMT channel at suspend time to avoid unwanted wake up events. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt --- drivers/clocksource/sh_cmt.c | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+) diff --git a/drivers/clocksource/sh_cmt.c b/drivers/clocksource/sh_cmt.c index 2964f5f4a7e..6b3e0c2f33e 100644 --- a/drivers/clocksource/sh_cmt.c +++ b/drivers/clocksource/sh_cmt.c @@ -40,6 +40,7 @@ struct sh_cmt_priv { struct platform_device *pdev; unsigned long flags; + unsigned long flags_suspend; unsigned long match_value; unsigned long next_match_value; unsigned long max_match_value; @@ -667,11 +668,38 @@ static int __devexit sh_cmt_remove(struct platform_device *pdev) return -EBUSY; /* cannot unregister clockevent and clocksource */ } +static int sh_cmt_suspend(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct sh_cmt_priv *p = platform_get_drvdata(pdev); + + /* save flag state and stop CMT channel */ + p->flags_suspend = p->flags; + sh_cmt_stop(p, p->flags); + return 0; +} + +static int sh_cmt_resume(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct sh_cmt_priv *p = platform_get_drvdata(pdev); + + /* start CMT channel from saved state */ + sh_cmt_start(p, p->flags_suspend); + return 0; +} + +static struct dev_pm_ops sh_cmt_dev_pm_ops = { + .suspend = sh_cmt_suspend, + .resume = sh_cmt_resume, +}; + static struct platform_driver sh_cmt_device_driver = { .probe = sh_cmt_probe, .remove = __devexit_p(sh_cmt_remove), .driver = { .name = "sh_cmt", + .pm = &sh_cmt_dev_pm_ops, } }; -- GitLab From 9747e78b304b44d6fb73e2c8071406d55aa8bb75 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Sat, 15 Aug 2009 02:53:34 +0000 Subject: [PATCH 1147/1342] sh: use in-soc KEYSC on se7724 This patch updates the Solution Engine 7724 board code to use in-SoC KEYSC resources for the keyboard platform device. Using the in-SoC key scan controller fixes a crash-during-resume issue. Without this patch the KEYSC hardware block located in the board specific FPGA is used together with an external IRQ which is routed through the FPGA and handled by some board specific demux code. This board specific FPGA interrupt code does not implement desc->set_wake() so the enable_irq_wake() call in the sh_keysc driver will fail at suspend-to-ram time and the disable_irq_wake() will bomb out when resuming. Changing the platform data to use the in-SoC KEYSC hardware makes the se7724 board support code less special which is a good thing. Also, the board specific KEYSC pin setup code selects in-SoC pin functions already which makes the current FPGA platform device data look like a typo. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt --- arch/sh/boards/mach-se/7724/setup.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) diff --git a/arch/sh/boards/mach-se/7724/setup.c b/arch/sh/boards/mach-se/7724/setup.c index 8fed45a2fb8..15456a0773b 100644 --- a/arch/sh/boards/mach-se/7724/setup.c +++ b/arch/sh/boards/mach-se/7724/setup.c @@ -238,7 +238,7 @@ static struct platform_device ceu1_device = { }, }; -/* KEYSC */ +/* KEYSC in SoC (Needs SW33-2 set to ON) */ static struct sh_keysc_info keysc_info = { .mode = SH_KEYSC_MODE_1, .scan_timing = 10, @@ -255,12 +255,13 @@ static struct sh_keysc_info keysc_info = { static struct resource keysc_resources[] = { [0] = { - .start = 0x1a204000, - .end = 0x1a20400f, + .name = "KEYSC", + .start = 0x044b0000, + .end = 0x044b000f, .flags = IORESOURCE_MEM, }, [1] = { - .start = IRQ0_KEY, + .start = 79, .flags = IORESOURCE_IRQ, }, }; -- GitLab From 237674e050ae8ea40a432412df6c15d60b7ae8a6 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Sat, 15 Aug 2009 02:53:42 +0000 Subject: [PATCH 1148/1342] sh: sh7724 ddr self-refresh changes This patch updates the SuperH Mobile sleep assembly code with support for DBSC memory controller found in the sh7724 processor. Without this fix the memory hooked up to the sh7724 processor will never enter self-refresh mode before suspending to ram. The effect of this is that the memory contents most likeley will be lost upon resume which may or may not be what you want. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt --- arch/sh/kernel/cpu/shmobile/sleep.S | 70 ++++++++++++++++++++++++++++- 1 file changed, 68 insertions(+), 2 deletions(-) diff --git a/arch/sh/kernel/cpu/shmobile/sleep.S b/arch/sh/kernel/cpu/shmobile/sleep.S index 5d888ef53d8..baf2d7d46b0 100644 --- a/arch/sh/kernel/cpu/shmobile/sleep.S +++ b/arch/sh/kernel/cpu/shmobile/sleep.S @@ -26,8 +26,30 @@ ENTRY(sh_mobile_standby) tst #SUSP_SH_SF, r0 bt skip_set_sf +#ifdef CONFIG_CPU_SUBTYPE_SH7724 + /* DBSC: put memory in self-refresh mode */ - /* SDRAM: disable power down and put in self-refresh mode */ + mov.l dben_reg, r4 + mov.l dben_data0, r1 + mov.l r1, @r4 + + mov.l dbrfpdn0_reg, r4 + mov.l dbrfpdn0_data0, r1 + mov.l r1, @r4 + + mov.l dbcmdcnt_reg, r4 + mov.l dbcmdcnt_data0, r1 + mov.l r1, @r4 + + mov.l dbcmdcnt_reg, r4 + mov.l dbcmdcnt_data1, r1 + mov.l r1, @r4 + + mov.l dbrfpdn0_reg, r4 + mov.l dbrfpdn0_data1, r1 + mov.l r1, @r4 +#else + /* SBSC: disable power down and put in self-refresh mode */ mov.l 1f, r4 mov.l 2f, r1 mov.l @r4, r2 @@ -35,6 +57,7 @@ ENTRY(sh_mobile_standby) mov.l 3f, r3 and r3, r2 mov.l r2, @r4 +#endif skip_set_sf: tst #SUSP_SH_SLEEP, r0 @@ -84,7 +107,36 @@ done_sleep: tst #SUSP_SH_SF, r0 bt skip_restore_sf - /* SDRAM: set auto-refresh mode */ +#ifdef CONFIG_CPU_SUBTYPE_SH7724 + /* DBSC: put memory in auto-refresh mode */ + + mov.l dbrfpdn0_reg, r4 + mov.l dbrfpdn0_data0, r1 + mov.l r1, @r4 + + /* sleep 140 ns */ + nop + nop + nop + nop + + mov.l dbcmdcnt_reg, r4 + mov.l dbcmdcnt_data0, r1 + mov.l r1, @r4 + + mov.l dbcmdcnt_reg, r4 + mov.l dbcmdcnt_data1, r1 + mov.l r1, @r4 + + mov.l dben_reg, r4 + mov.l dben_data1, r1 + mov.l r1, @r4 + + mov.l dbrfpdn0_reg, r4 + mov.l dbrfpdn0_data2, r1 + mov.l r1, @r4 +#else + /* SBSC: set auto-refresh mode */ mov.l 1f, r4 mov.l @r4, r2 mov.l 4f, r3 @@ -98,15 +150,29 @@ done_sleep: add r4, r3 or r2, r3 mov.l r3, @r1 +#endif skip_restore_sf: rts nop .balign 4 +#ifdef CONFIG_CPU_SUBTYPE_SH7724 +dben_reg: .long 0xfd000010 /* DBEN */ +dben_data0: .long 0 +dben_data1: .long 1 +dbrfpdn0_reg: .long 0xfd000040 /* DBRFPDN0 */ +dbrfpdn0_data0: .long 0 +dbrfpdn0_data1: .long 1 +dbrfpdn0_data2: .long 0x00010000 +dbcmdcnt_reg: .long 0xfd000014 /* DBCMDCNT */ +dbcmdcnt_data0: .long 2 +dbcmdcnt_data1: .long 4 +#else 1: .long 0xfe400008 /* SDCR0 */ 2: .long 0x00000400 3: .long 0xffff7fff 4: .long 0xfffffbff +#endif 5: .long 0xa4150020 /* STBCR */ 6: .long 0xfe40001c /* RTCOR */ 7: .long 0xfe400018 /* RTCNT */ -- GitLab From 3ef12c3c97603bad405d30c989718cc9405e2759 Mon Sep 17 00:00:00 2001 From: Cliff Wickman Date: Fri, 14 Aug 2009 13:56:37 -0500 Subject: [PATCH 1149/1342] x86: Fix UV BAU destination subnode id The SGI UV Broadcast Assist Unit is used to send TLB shootdown messages to remote nodes of the system. The header of the message must contain the subnode id of the block in the receiving hub that handles such messages. It should always be 0x10, the id of the "LB" block. It had previously been documented as a "must be zero" field. Signed-off-by: Cliff Wickman Acked-by: Jack Steiner LKML-Reference: Signed-off-by: Ingo Molnar --- arch/x86/include/asm/uv/uv_bau.h | 2 +- arch/x86/kernel/tlb_uv.c | 1 + 2 files changed, 2 insertions(+), 1 deletion(-) diff --git a/arch/x86/include/asm/uv/uv_bau.h b/arch/x86/include/asm/uv/uv_bau.h index bddd44f2f0a..80e2984f521 100644 --- a/arch/x86/include/asm/uv/uv_bau.h +++ b/arch/x86/include/asm/uv/uv_bau.h @@ -133,7 +133,7 @@ struct bau_msg_payload { * see table 4.2.3.0.1 in broacast_assist spec. */ struct bau_msg_header { - unsigned int dest_subnodeid:6; /* must be zero */ + unsigned int dest_subnodeid:6; /* must be 0x10, for the LB */ /* bits 5:0 */ unsigned int base_dest_nodeid:15; /* nasid>>1 (pnode) of */ /* bits 20:6 */ /* first bit in node_map */ diff --git a/arch/x86/kernel/tlb_uv.c b/arch/x86/kernel/tlb_uv.c index 8ccabb8a2f6..77b9689f8ed 100644 --- a/arch/x86/kernel/tlb_uv.c +++ b/arch/x86/kernel/tlb_uv.c @@ -744,6 +744,7 @@ uv_activation_descriptor_init(int node, int pnode) * note that base_dest_nodeid is actually a nasid. */ ad2->header.base_dest_nodeid = uv_partition_base_pnode << 1; + ad2->header.dest_subnodeid = 0x10; /* the LB */ ad2->header.command = UV_NET_ENDPOINT_INTD; ad2->header.int_both = 1; /* -- GitLab From 39e6dd73502f64e2ae3236b304e160ae30de9384 Mon Sep 17 00:00:00 2001 From: Arnaldo Carvalho de Melo Date: Fri, 14 Aug 2009 15:26:32 -0300 Subject: [PATCH 1150/1342] perf record: Fix typo in pid_synthesize_comm_event We were using 'fd' locally, but there was a global 'fd' too, so when converting from open to fopen the test made against fd should be made against 'fp', but since we have that global it didnt get discovered ... Reported-by: Ulrich Drepper Signed-off-by: Arnaldo Carvalho de Melo Cc: Peter Zijlstra LKML-Reference: <20090814182632.GF3490@ghostprotocols.net> Signed-off-by: Ingo Molnar --- tools/perf/builtin-record.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/tools/perf/builtin-record.c b/tools/perf/builtin-record.c index 3d051b9cf25..89a5ddcd1de 100644 --- a/tools/perf/builtin-record.c +++ b/tools/perf/builtin-record.c @@ -219,7 +219,7 @@ static pid_t pid_synthesize_comm_event(pid_t pid, int full) snprintf(filename, sizeof(filename), "/proc/%d/status", pid); fp = fopen(filename, "r"); - if (fd == NULL) { + if (fp == NULL) { /* * We raced with a task exiting - just return: */ -- GitLab From dde5828f56cb2c1aa70365c476e6830482127258 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sat, 15 Aug 2009 12:36:00 +0100 Subject: [PATCH 1151/1342] ARM: Fix broken highmem support Currently, highmem is selectable, and you can request an increased vmalloc area. However, none of this has any effect on the memory layout since a patch in the highmem series was accidentally dropped. Moreover, even if you did want highmem, all memory would still be registered as lowmem, possibly resulting in overflow of the available virtual mapping space. The highmem boundary is determined by the highest allowed beginning of the vmalloc area, which depends on its configurable minimum size (see commit 60296c71f6c5063e3c1f1d2619ca0b60940162e7 for details on this). We should create mappings and initialize bootmem only for low memory, while the zone allocator must still be told about highmem. Currently, memory nodes which are completely located in high memory are not supported. This is not a huge limitation since systems relying on highmem support are unlikely to have discontiguous memory with large holes. [ A similar patch was meant to be merged before commit 5f0fbf9ecaf3 and be available in Linux v2.6.30, however some git rebase screw-up of mine dropped the first commit of the series, and that goofage escaped testing somehow as well. -- Nico ] Signed-off-by: Russell King Reviewed-by: Nicolas Pitre --- arch/arm/include/asm/setup.h | 3 +- arch/arm/mm/init.c | 118 ++++++++++++++++++++++------------- arch/arm/mm/mmu.c | 9 ++- 3 files changed, 83 insertions(+), 47 deletions(-) diff --git a/arch/arm/include/asm/setup.h b/arch/arm/include/asm/setup.h index ee1304f22f9..5ccce0a9b03 100644 --- a/arch/arm/include/asm/setup.h +++ b/arch/arm/include/asm/setup.h @@ -201,7 +201,8 @@ static struct tagtable __tagtable_##fn __tag = { tag, fn } struct membank { unsigned long start; unsigned long size; - int node; + unsigned short node; + unsigned short highmem; }; struct meminfo { diff --git a/arch/arm/mm/init.c b/arch/arm/mm/init.c index 8277802ec85..3a7279c1ce5 100644 --- a/arch/arm/mm/init.c +++ b/arch/arm/mm/init.c @@ -120,6 +120,32 @@ void show_mem(void) printk("%d pages swap cached\n", cached); } +static void __init find_node_limits(int node, struct meminfo *mi, + unsigned long *min, unsigned long *max_low, unsigned long *max_high) +{ + int i; + + *min = -1UL; + *max_low = *max_high = 0; + + for_each_nodebank(i, mi, node) { + struct membank *bank = &mi->bank[i]; + unsigned long start, end; + + start = bank_pfn_start(bank); + end = bank_pfn_end(bank); + + if (*min > start) + *min = start; + if (*max_high < end) + *max_high = end; + if (bank->highmem) + continue; + if (*max_low < end) + *max_low = end; + } +} + /* * FIXME: We really want to avoid allocating the bootmap bitmap * over the top of the initrd. Hopefully, this is located towards @@ -210,40 +236,24 @@ static inline void map_memory_bank(struct membank *bank) #endif } -static unsigned long __init bootmem_init_node(int node, struct meminfo *mi) +static void __init bootmem_init_node(int node, struct meminfo *mi, + unsigned long start_pfn, unsigned long end_pfn) { - unsigned long start_pfn, end_pfn, boot_pfn; + unsigned long boot_pfn; unsigned int boot_pages; pg_data_t *pgdat; int i; - start_pfn = -1UL; - end_pfn = 0; - /* - * Calculate the pfn range, and map the memory banks for this node. + * Map the memory banks for this node. */ for_each_nodebank(i, mi, node) { struct membank *bank = &mi->bank[i]; - unsigned long start, end; - start = bank_pfn_start(bank); - end = bank_pfn_end(bank); - - if (start_pfn > start) - start_pfn = start; - if (end_pfn < end) - end_pfn = end; - - map_memory_bank(bank); + if (!bank->highmem) + map_memory_bank(bank); } - /* - * If there is no memory in this node, ignore it. - */ - if (end_pfn == 0) - return end_pfn; - /* * Allocate the bootmem bitmap page. */ @@ -260,7 +270,8 @@ static unsigned long __init bootmem_init_node(int node, struct meminfo *mi) for_each_nodebank(i, mi, node) { struct membank *bank = &mi->bank[i]; - free_bootmem_node(pgdat, bank_phys_start(bank), bank_phys_size(bank)); + if (!bank->highmem) + free_bootmem_node(pgdat, bank_phys_start(bank), bank_phys_size(bank)); memory_present(node, bank_pfn_start(bank), bank_pfn_end(bank)); } @@ -269,8 +280,6 @@ static unsigned long __init bootmem_init_node(int node, struct meminfo *mi) */ reserve_bootmem_node(pgdat, boot_pfn << PAGE_SHIFT, boot_pages << PAGE_SHIFT, BOOTMEM_DEFAULT); - - return end_pfn; } static void __init bootmem_reserve_initrd(int node) @@ -297,33 +306,39 @@ static void __init bootmem_reserve_initrd(int node) static void __init bootmem_free_node(int node, struct meminfo *mi) { unsigned long zone_size[MAX_NR_ZONES], zhole_size[MAX_NR_ZONES]; - unsigned long start_pfn, end_pfn; - pg_data_t *pgdat = NODE_DATA(node); + unsigned long min, max_low, max_high; int i; - start_pfn = pgdat->bdata->node_min_pfn; - end_pfn = pgdat->bdata->node_low_pfn; + find_node_limits(node, mi, &min, &max_low, &max_high); /* * initialise the zones within this node. */ memset(zone_size, 0, sizeof(zone_size)); - memset(zhole_size, 0, sizeof(zhole_size)); /* * The size of this node has already been determined. If we need * to do anything fancy with the allocation of this memory to the * zones, now is the time to do it. */ - zone_size[0] = end_pfn - start_pfn; + zone_size[0] = max_low - min; +#ifdef CONFIG_HIGHMEM + zone_size[ZONE_HIGHMEM] = max_high - max_low; +#endif /* * For each bank in this node, calculate the size of the holes. * holes = node_size - sum(bank_sizes_in_node) */ - zhole_size[0] = zone_size[0]; - for_each_nodebank(i, mi, node) - zhole_size[0] -= bank_pfn_size(&mi->bank[i]); + memcpy(zhole_size, zone_size, sizeof(zhole_size)); + for_each_nodebank(i, mi, node) { + int idx = 0; +#ifdef CONFIG_HIGHMEM + if (mi->bank[i].highmem) + idx = ZONE_HIGHMEM; +#endif + zhole_size[idx] -= bank_pfn_size(&mi->bank[i]); + } /* * Adjust the sizes according to any special requirements for @@ -331,13 +346,13 @@ static void __init bootmem_free_node(int node, struct meminfo *mi) */ arch_adjust_zones(node, zone_size, zhole_size); - free_area_init_node(node, zone_size, start_pfn, zhole_size); + free_area_init_node(node, zone_size, min, zhole_size); } void __init bootmem_init(void) { struct meminfo *mi = &meminfo; - unsigned long memend_pfn = 0; + unsigned long min, max_low, max_high; int node, initrd_node; /* @@ -345,11 +360,29 @@ void __init bootmem_init(void) */ initrd_node = check_initrd(mi); + max_low = max_high = 0; + /* * Run through each node initialising the bootmem allocator. */ for_each_node(node) { - unsigned long end_pfn = bootmem_init_node(node, mi); + unsigned long node_low, node_high; + + find_node_limits(node, mi, &min, &node_low, &node_high); + + if (node_low > max_low) + max_low = node_low; + if (node_high > max_high) + max_high = node_high; + + /* + * If there is no memory in this node, ignore it. + * (We can't have nodes which have no lowmem) + */ + if (node_low == 0) + continue; + + bootmem_init_node(node, mi, min, node_low); /* * Reserve any special node zero regions. @@ -362,12 +395,6 @@ void __init bootmem_init(void) */ if (node == initrd_node) bootmem_reserve_initrd(node); - - /* - * Remember the highest memory PFN. - */ - if (end_pfn > memend_pfn) - memend_pfn = end_pfn; } /* @@ -383,7 +410,7 @@ void __init bootmem_init(void) for_each_node(node) bootmem_free_node(node, mi); - high_memory = __va((memend_pfn << PAGE_SHIFT) - 1) + 1; + high_memory = __va((max_low << PAGE_SHIFT) - 1) + 1; /* * This doesn't seem to be used by the Linux memory manager any @@ -393,7 +420,8 @@ void __init bootmem_init(void) * Note: max_low_pfn and max_pfn reflect the number of _pages_ in * the system, not the maximum PFN. */ - max_pfn = max_low_pfn = memend_pfn - PHYS_PFN_OFFSET; + max_low_pfn = max_low - PHYS_PFN_OFFSET; + max_pfn = max_high - PHYS_PFN_OFFSET; } static inline int free_area(unsigned long pfn, unsigned long end, char *s) diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c index 4722582b17b..4426ee67cec 100644 --- a/arch/arm/mm/mmu.c +++ b/arch/arm/mm/mmu.c @@ -687,13 +687,19 @@ __early_param("vmalloc=", early_vmalloc); static void __init sanity_check_meminfo(void) { - int i, j; + int i, j, highmem = 0; for (i = 0, j = 0; i < meminfo.nr_banks; i++) { struct membank *bank = &meminfo.bank[j]; *bank = meminfo.bank[i]; #ifdef CONFIG_HIGHMEM + if (__va(bank->start) > VMALLOC_MIN || + __va(bank->start) < (void *)PAGE_OFFSET) + highmem = 1; + + bank->highmem = highmem; + /* * Split those memory banks which are partially overlapping * the vmalloc area greatly simplifying things later. @@ -714,6 +720,7 @@ static void __init sanity_check_meminfo(void) i++; bank[1].size -= VMALLOC_MIN - __va(bank->start); bank[1].start = __pa(VMALLOC_MIN - 1) + 1; + bank[1].highmem = highmem = 1; j++; } bank->size = VMALLOC_MIN - __va(bank->start); -- GitLab From c5e7f5a38a7ebf3697281bc7cb494e676f287ac0 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Wed, 3 Jun 2009 13:05:48 +0200 Subject: [PATCH 1152/1342] [WATCHDOG] ar7_wdt: fix path to ar7-specific headers AR7 is currently being resubmitted for mainline inclusion and we changed the path to the ar7-specific headers from ar7 to mach-ar7 to reflect the other MIPS-based boards header hierarchy. This patch will avoid any future compilation failure due to missing headers. Signed-off-by: Florian Fainelli Signed-off-by: Wim Van Sebroeck --- drivers/watchdog/ar7_wdt.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/watchdog/ar7_wdt.c b/drivers/watchdog/ar7_wdt.c index 3fe9742c23c..2f8643efe92 100644 --- a/drivers/watchdog/ar7_wdt.c +++ b/drivers/watchdog/ar7_wdt.c @@ -37,7 +37,7 @@ #include #include -#include +#include #define DRVNAME "ar7_wdt" #define LONGNAME "TI AR7 Watchdog Timer" -- GitLab From a2bb9f4d6a5a589b481595207ac3588cc08d1b60 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Thu, 13 Aug 2009 21:57:22 +0100 Subject: [PATCH 1153/1342] ARM: 5673/1: U300 fix initsection compile warning The u300_init_check_chip() function was not properly tagged with the __init macro and provided a initsection mismatch on compilation. Signed-off-by: Linus Walleij Signed-off-by: Russell King --- arch/arm/mach-u300/core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c index 7936085dd75..2e9b8ccd8ec 100644 --- a/arch/arm/mach-u300/core.c +++ b/arch/arm/mach-u300/core.c @@ -510,7 +510,7 @@ static struct db_chip db_chips[] __initdata = { } }; -static void u300_init_check_chip(void) +static void __init u300_init_check_chip(void) { u16 val; -- GitLab From 3f8befec95d5c1bbc6e247e1a5dafa82519530f9 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Sat, 15 Aug 2009 20:54:13 +1000 Subject: [PATCH 1154/1342] drm/radeon/kms: add rv530 R300_SU_REG_DEST + reloc for ZPASS_ADDR These are needed for Occulsion Query support. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r300.c | 15 +++++++++++++++ 1 file changed, 15 insertions(+) diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c index 9c8d41534a5..8594486e162 100644 --- a/drivers/gpu/drm/radeon/r300.c +++ b/drivers/gpu/drm/radeon/r300.c @@ -1403,6 +1403,21 @@ static int r300_packet0_check(struct radeon_cs_parser *p, tmp = (ib_chunk->kdata[idx] >> 22) & 0xF; track->textures[i].txdepth = tmp; break; + case R300_ZB_ZPASS_ADDR: + r = r100_cs_packet_next_reloc(p, &reloc); + if (r) { + DRM_ERROR("No reloc for ib[%d]=0x%04X\n", + idx, reg); + r100_cs_dump_packet(p, pkt); + return r; + } + ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset); + break; + case 0x4be8: + /* valid register only on RV530 */ + if (p->rdev->family == CHIP_RV530) + break; + /* fallthrough do not move */ default: printk(KERN_ERR "Forbidden register 0x%04X in cs at %d\n", reg, idx); -- GitLab From 7ed220d738cf16adff6bc3b31ad25b8848a2fa9c Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Michel=20D=C3=A4nzer?= Date: Thu, 13 Aug 2009 11:10:51 +0200 Subject: [PATCH 1155/1342] drm/radeon/kms: Fix up vertical blank interrupt support. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Fixes 3D apps timing out in the WAIT_VBLANK ioctl. AVIVO bits compile-tested only. Signed-off-by: Michel Dänzer Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 66 +++++++++++++++++ drivers/gpu/drm/radeon/r500_reg.h | 16 +++- drivers/gpu/drm/radeon/radeon.h | 2 + drivers/gpu/drm/radeon/radeon_asic.h | 23 ++++-- drivers/gpu/drm/radeon/radeon_irq_kms.c | 54 -------------- drivers/gpu/drm/radeon/radeon_kms.c | 33 +++++++-- drivers/gpu/drm/radeon/radeon_legacy_crtc.c | 7 +- drivers/gpu/drm/radeon/radeon_reg.h | 11 ++- drivers/gpu/drm/radeon/rs600.c | 82 +++++++++++++++++++++ 9 files changed, 217 insertions(+), 77 deletions(-) diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index f1ba8ff4113..e1a6e82b996 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -253,6 +253,72 @@ void r100_mc_fini(struct radeon_device *rdev) } +/* + * Interrupts + */ +int r100_irq_set(struct radeon_device *rdev) +{ + uint32_t tmp = 0; + + if (rdev->irq.sw_int) { + tmp |= RADEON_SW_INT_ENABLE; + } + if (rdev->irq.crtc_vblank_int[0]) { + tmp |= RADEON_CRTC_VBLANK_MASK; + } + if (rdev->irq.crtc_vblank_int[1]) { + tmp |= RADEON_CRTC2_VBLANK_MASK; + } + WREG32(RADEON_GEN_INT_CNTL, tmp); + return 0; +} + +static inline uint32_t r100_irq_ack(struct radeon_device *rdev) +{ + uint32_t irqs = RREG32(RADEON_GEN_INT_STATUS); + uint32_t irq_mask = RADEON_SW_INT_TEST | RADEON_CRTC_VBLANK_STAT | + RADEON_CRTC2_VBLANK_STAT; + + if (irqs) { + WREG32(RADEON_GEN_INT_STATUS, irqs); + } + return irqs & irq_mask; +} + +int r100_irq_process(struct radeon_device *rdev) +{ + uint32_t status; + + status = r100_irq_ack(rdev); + if (!status) { + return IRQ_NONE; + } + while (status) { + /* SW interrupt */ + if (status & RADEON_SW_INT_TEST) { + radeon_fence_process(rdev); + } + /* Vertical blank interrupts */ + if (status & RADEON_CRTC_VBLANK_STAT) { + drm_handle_vblank(rdev->ddev, 0); + } + if (status & RADEON_CRTC2_VBLANK_STAT) { + drm_handle_vblank(rdev->ddev, 1); + } + status = r100_irq_ack(rdev); + } + return IRQ_HANDLED; +} + +u32 r100_get_vblank_counter(struct radeon_device *rdev, int crtc) +{ + if (crtc == 0) + return RREG32(RADEON_CRTC_CRNT_FRAME); + else + return RREG32(RADEON_CRTC2_CRNT_FRAME); +} + + /* * Fence emission */ diff --git a/drivers/gpu/drm/radeon/r500_reg.h b/drivers/gpu/drm/radeon/r500_reg.h index 036691b38cb..e1d5e0331e1 100644 --- a/drivers/gpu/drm/radeon/r500_reg.h +++ b/drivers/gpu/drm/radeon/r500_reg.h @@ -350,6 +350,7 @@ #define AVIVO_D1CRTC_BLANK_CONTROL 0x6084 #define AVIVO_D1CRTC_INTERLACE_CONTROL 0x6088 #define AVIVO_D1CRTC_INTERLACE_STATUS 0x608c +#define AVIVO_D1CRTC_FRAME_COUNT 0x60a4 #define AVIVO_D1CRTC_STEREO_CONTROL 0x60c4 /* master controls */ @@ -438,14 +439,15 @@ # define AVIVO_DC_LB_DISP1_END_ADR_SHIFT 4 # define AVIVO_DC_LB_DISP1_END_ADR_MASK 0x7ff -#define R500_DxMODE_INT_MASK 0x6540 -#define R500_D1MODE_INT_MASK (1<<0) -#define R500_D2MODE_INT_MASK (1<<8) - #define AVIVO_D1MODE_DATA_FORMAT 0x6528 # define AVIVO_D1MODE_INTERLEAVE_EN (1 << 0) #define AVIVO_D1MODE_DESKTOP_HEIGHT 0x652C +#define AVIVO_D1MODE_VBLANK_STATUS 0x6534 +# define AVIVO_VBLANK_ACK (1 << 4) #define AVIVO_D1MODE_VLINE_START_END 0x6538 +#define AVIVO_DxMODE_INT_MASK 0x6540 +# define AVIVO_D1MODE_INT_MASK (1 << 0) +# define AVIVO_D2MODE_INT_MASK (1 << 8) #define AVIVO_D1MODE_VIEWPORT_START 0x6580 #define AVIVO_D1MODE_VIEWPORT_SIZE 0x6584 #define AVIVO_D1MODE_EXT_OVERSCAN_LEFT_RIGHT 0x6588 @@ -475,6 +477,7 @@ #define AVIVO_D2CRTC_BLANK_CONTROL 0x6884 #define AVIVO_D2CRTC_INTERLACE_CONTROL 0x6888 #define AVIVO_D2CRTC_INTERLACE_STATUS 0x688c +#define AVIVO_D2CRTC_FRAME_COUNT 0x68a4 #define AVIVO_D2CRTC_STEREO_CONTROL 0x68c4 #define AVIVO_D2GRPH_ENABLE 0x6900 @@ -497,6 +500,7 @@ #define AVIVO_D2CUR_SIZE 0x6c10 #define AVIVO_D2CUR_POSITION 0x6c14 +#define AVIVO_D2MODE_VBLANK_STATUS 0x6d34 #define AVIVO_D2MODE_VLINE_START_END 0x6d38 #define AVIVO_D2MODE_VIEWPORT_START 0x6d80 #define AVIVO_D2MODE_VIEWPORT_SIZE 0x6d84 @@ -748,4 +752,8 @@ # define AVIVO_I2C_EN (1 << 0) # define AVIVO_I2C_RESET (1 << 8) +#define AVIVO_DISP_INTERRUPT_STATUS 0x7edc +# define AVIVO_D1_VBLANK_INTERRUPT (1 << 4) +# define AVIVO_D2_VBLANK_INTERRUPT (1 << 5) + #endif diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index b1d945b8ed6..34611274084 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -574,6 +574,7 @@ struct radeon_asic { void (*ring_start)(struct radeon_device *rdev); int (*irq_set)(struct radeon_device *rdev); int (*irq_process)(struct radeon_device *rdev); + u32 (*get_vblank_counter)(struct radeon_device *rdev, int crtc); void (*fence_ring_emit)(struct radeon_device *rdev, struct radeon_fence *fence); int (*cs_parse)(struct radeon_cs_parser *p); int (*copy_blit)(struct radeon_device *rdev, @@ -862,6 +863,7 @@ static inline void radeon_ring_write(struct radeon_device *rdev, uint32_t v) #define radeon_ring_start(rdev) (rdev)->asic->ring_start((rdev)) #define radeon_irq_set(rdev) (rdev)->asic->irq_set((rdev)) #define radeon_irq_process(rdev) (rdev)->asic->irq_process((rdev)) +#define radeon_get_vblank_counter(rdev, crtc) (rdev)->asic->get_vblank_counter((rdev), (crtc)) #define radeon_fence_ring_emit(rdev, fence) (rdev)->asic->fence_ring_emit((rdev), (fence)) #define radeon_copy_blit(rdev, s, d, np, f) (rdev)->asic->copy_blit((rdev), (s), (d), (np), (f)) #define radeon_copy_dma(rdev, s, d, np, f) (rdev)->asic->copy_dma((rdev), (s), (d), (np), (f)) diff --git a/drivers/gpu/drm/radeon/radeon_asic.h b/drivers/gpu/drm/radeon/radeon_asic.h index c0ae2d92325..7ca6c13569b 100644 --- a/drivers/gpu/drm/radeon/radeon_asic.h +++ b/drivers/gpu/drm/radeon/radeon_asic.h @@ -49,6 +49,7 @@ void r100_vram_info(struct radeon_device *rdev); int r100_gpu_reset(struct radeon_device *rdev); int r100_mc_init(struct radeon_device *rdev); void r100_mc_fini(struct radeon_device *rdev); +u32 r100_get_vblank_counter(struct radeon_device *rdev, int crtc); int r100_wb_init(struct radeon_device *rdev); void r100_wb_fini(struct radeon_device *rdev); int r100_gart_enable(struct radeon_device *rdev); @@ -96,6 +97,7 @@ static struct radeon_asic r100_asic = { .ring_start = &r100_ring_start, .irq_set = &r100_irq_set, .irq_process = &r100_irq_process, + .get_vblank_counter = &r100_get_vblank_counter, .fence_ring_emit = &r100_fence_ring_emit, .cs_parse = &r100_cs_parse, .copy_blit = &r100_copy_blit, @@ -156,6 +158,7 @@ static struct radeon_asic r300_asic = { .ring_start = &r300_ring_start, .irq_set = &r100_irq_set, .irq_process = &r100_irq_process, + .get_vblank_counter = &r100_get_vblank_counter, .fence_ring_emit = &r300_fence_ring_emit, .cs_parse = &r300_cs_parse, .copy_blit = &r100_copy_blit, @@ -196,6 +199,7 @@ static struct radeon_asic r420_asic = { .ring_start = &r300_ring_start, .irq_set = &r100_irq_set, .irq_process = &r100_irq_process, + .get_vblank_counter = &r100_get_vblank_counter, .fence_ring_emit = &r300_fence_ring_emit, .cs_parse = &r300_cs_parse, .copy_blit = &r100_copy_blit, @@ -243,6 +247,7 @@ static struct radeon_asic rs400_asic = { .ring_start = &r300_ring_start, .irq_set = &r100_irq_set, .irq_process = &r100_irq_process, + .get_vblank_counter = &r100_get_vblank_counter, .fence_ring_emit = &r300_fence_ring_emit, .cs_parse = &r300_cs_parse, .copy_blit = &r100_copy_blit, @@ -266,6 +271,8 @@ void rs600_vram_info(struct radeon_device *rdev); int rs600_mc_init(struct radeon_device *rdev); void rs600_mc_fini(struct radeon_device *rdev); int rs600_irq_set(struct radeon_device *rdev); +int rs600_irq_process(struct radeon_device *rdev); +u32 rs600_get_vblank_counter(struct radeon_device *rdev, int crtc); int rs600_gart_enable(struct radeon_device *rdev); void rs600_gart_disable(struct radeon_device *rdev); void rs600_gart_tlb_flush(struct radeon_device *rdev); @@ -291,7 +298,8 @@ static struct radeon_asic rs600_asic = { .cp_disable = &r100_cp_disable, .ring_start = &r300_ring_start, .irq_set = &rs600_irq_set, - .irq_process = &r100_irq_process, + .irq_process = &rs600_irq_process, + .get_vblank_counter = &rs600_get_vblank_counter, .fence_ring_emit = &r300_fence_ring_emit, .cs_parse = &r300_cs_parse, .copy_blit = &r100_copy_blit, @@ -334,7 +342,8 @@ static struct radeon_asic rs690_asic = { .cp_disable = &r100_cp_disable, .ring_start = &r300_ring_start, .irq_set = &rs600_irq_set, - .irq_process = &r100_irq_process, + .irq_process = &rs600_irq_process, + .get_vblank_counter = &rs600_get_vblank_counter, .fence_ring_emit = &r300_fence_ring_emit, .cs_parse = &r300_cs_parse, .copy_blit = &r100_copy_blit, @@ -382,8 +391,9 @@ static struct radeon_asic rv515_asic = { .cp_fini = &r100_cp_fini, .cp_disable = &r100_cp_disable, .ring_start = &rv515_ring_start, - .irq_set = &r100_irq_set, - .irq_process = &r100_irq_process, + .irq_set = &rs600_irq_set, + .irq_process = &rs600_irq_process, + .get_vblank_counter = &rs600_get_vblank_counter, .fence_ring_emit = &r300_fence_ring_emit, .cs_parse = &r300_cs_parse, .copy_blit = &r100_copy_blit, @@ -424,8 +434,9 @@ static struct radeon_asic r520_asic = { .cp_fini = &r100_cp_fini, .cp_disable = &r100_cp_disable, .ring_start = &rv515_ring_start, - .irq_set = &r100_irq_set, - .irq_process = &r100_irq_process, + .irq_set = &rs600_irq_set, + .irq_process = &rs600_irq_process, + .get_vblank_counter = &rs600_get_vblank_counter, .fence_ring_emit = &r300_fence_ring_emit, .cs_parse = &r300_cs_parse, .copy_blit = &r100_copy_blit, diff --git a/drivers/gpu/drm/radeon/radeon_irq_kms.c b/drivers/gpu/drm/radeon/radeon_irq_kms.c index 491d569deb0..9805e4b6ca1 100644 --- a/drivers/gpu/drm/radeon/radeon_irq_kms.c +++ b/drivers/gpu/drm/radeon/radeon_irq_kms.c @@ -32,60 +32,6 @@ #include "radeon.h" #include "atom.h" -static inline uint32_t r100_irq_ack(struct radeon_device *rdev) -{ - uint32_t irqs = RREG32(RADEON_GEN_INT_STATUS); - uint32_t irq_mask = RADEON_SW_INT_TEST; - - if (irqs) { - WREG32(RADEON_GEN_INT_STATUS, irqs); - } - return irqs & irq_mask; -} - -int r100_irq_set(struct radeon_device *rdev) -{ - uint32_t tmp = 0; - - if (rdev->irq.sw_int) { - tmp |= RADEON_SW_INT_ENABLE; - } - /* Todo go through CRTC and enable vblank int or not */ - WREG32(RADEON_GEN_INT_CNTL, tmp); - return 0; -} - -int r100_irq_process(struct radeon_device *rdev) -{ - uint32_t status; - - status = r100_irq_ack(rdev); - if (!status) { - return IRQ_NONE; - } - while (status) { - /* SW interrupt */ - if (status & RADEON_SW_INT_TEST) { - radeon_fence_process(rdev); - } - status = r100_irq_ack(rdev); - } - return IRQ_HANDLED; -} - -int rs600_irq_set(struct radeon_device *rdev) -{ - uint32_t tmp = 0; - - if (rdev->irq.sw_int) { - tmp |= RADEON_SW_INT_ENABLE; - } - WREG32(RADEON_GEN_INT_CNTL, tmp); - /* Todo go through CRTC and enable vblank int or not */ - WREG32(R500_DxMODE_INT_MASK, 0); - return 0; -} - irqreturn_t radeon_driver_irq_handler_kms(DRM_IRQ_ARGS) { struct drm_device *dev = (struct drm_device *) arg; diff --git a/drivers/gpu/drm/radeon/radeon_kms.c b/drivers/gpu/drm/radeon/radeon_kms.c index 3357110e30c..d2764bf6b2a 100644 --- a/drivers/gpu/drm/radeon/radeon_kms.c +++ b/drivers/gpu/drm/radeon/radeon_kms.c @@ -141,19 +141,42 @@ void radeon_driver_preclose_kms(struct drm_device *dev, */ u32 radeon_get_vblank_counter_kms(struct drm_device *dev, int crtc) { - /* FIXME: implement */ - return 0; + struct radeon_device *rdev = dev->dev_private; + + if (crtc < 0 || crtc > 1) { + DRM_ERROR("Invalid crtc %d\n", crtc); + return -EINVAL; + } + + return radeon_get_vblank_counter(rdev, crtc); } int radeon_enable_vblank_kms(struct drm_device *dev, int crtc) { - /* FIXME: implement */ - return 0; + struct radeon_device *rdev = dev->dev_private; + + if (crtc < 0 || crtc > 1) { + DRM_ERROR("Invalid crtc %d\n", crtc); + return -EINVAL; + } + + rdev->irq.crtc_vblank_int[crtc] = true; + + return radeon_irq_set(rdev); } void radeon_disable_vblank_kms(struct drm_device *dev, int crtc) { - /* FIXME: implement */ + struct radeon_device *rdev = dev->dev_private; + + if (crtc < 0 || crtc > 1) { + DRM_ERROR("Invalid crtc %d\n", crtc); + return; + } + + rdev->irq.crtc_vblank_int[crtc] = false; + + radeon_irq_set(rdev); } diff --git a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c index 7d06dc98a42..0da72f18fd3 100644 --- a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c +++ b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c @@ -310,10 +310,13 @@ void radeon_crtc_dpms(struct drm_crtc *crtc, int mode) RADEON_CRTC_DISP_REQ_EN_B)); WREG32_P(RADEON_CRTC_EXT_CNTL, 0, ~mask); } + drm_vblank_post_modeset(dev, radeon_crtc->crtc_id); + radeon_crtc_load_lut(crtc); break; case DRM_MODE_DPMS_STANDBY: case DRM_MODE_DPMS_SUSPEND: case DRM_MODE_DPMS_OFF: + drm_vblank_pre_modeset(dev, radeon_crtc->crtc_id); if (radeon_crtc->crtc_id) WREG32_P(RADEON_CRTC2_GEN_CNTL, mask, ~mask); else { @@ -323,10 +326,6 @@ void radeon_crtc_dpms(struct drm_crtc *crtc, int mode) } break; } - - if (mode != DRM_MODE_DPMS_OFF) { - radeon_crtc_load_lut(crtc); - } } /* properly set crtc bpp when using atombios */ diff --git a/drivers/gpu/drm/radeon/radeon_reg.h b/drivers/gpu/drm/radeon/radeon_reg.h index e1b61857446..5a098f304ed 100644 --- a/drivers/gpu/drm/radeon/radeon_reg.h +++ b/drivers/gpu/drm/radeon/radeon_reg.h @@ -982,12 +982,15 @@ # define RS400_TMDS2_PLLRST (1 << 1) #define RADEON_GEN_INT_CNTL 0x0040 +# define RADEON_CRTC_VBLANK_MASK (1 << 0) +# define RADEON_CRTC2_VBLANK_MASK (1 << 9) # define RADEON_SW_INT_ENABLE (1 << 25) #define RADEON_GEN_INT_STATUS 0x0044 -# define RADEON_VSYNC_INT_AK (1 << 2) -# define RADEON_VSYNC_INT (1 << 2) -# define RADEON_VSYNC2_INT_AK (1 << 6) -# define RADEON_VSYNC2_INT (1 << 6) +# define AVIVO_DISPLAY_INT_STATUS (1 << 0) +# define RADEON_CRTC_VBLANK_STAT (1 << 0) +# define RADEON_CRTC_VBLANK_STAT_ACK (1 << 0) +# define RADEON_CRTC2_VBLANK_STAT (1 << 9) +# define RADEON_CRTC2_VBLANK_STAT_ACK (1 << 9) # define RADEON_SW_INT_FIRE (1 << 26) # define RADEON_SW_INT_TEST (1 << 25) # define RADEON_SW_INT_TEST_ACK (1 << 25) diff --git a/drivers/gpu/drm/radeon/rs600.c b/drivers/gpu/drm/radeon/rs600.c index bbea6dee4a9..7e8ce983a90 100644 --- a/drivers/gpu/drm/radeon/rs600.c +++ b/drivers/gpu/drm/radeon/rs600.c @@ -239,6 +239,88 @@ void rs600_mc_fini(struct radeon_device *rdev) } +/* + * Interrupts + */ +int rs600_irq_set(struct radeon_device *rdev) +{ + uint32_t tmp = 0; + uint32_t mode_int = 0; + + if (rdev->irq.sw_int) { + tmp |= RADEON_SW_INT_ENABLE; + } + if (rdev->irq.crtc_vblank_int[0]) { + tmp |= AVIVO_DISPLAY_INT_STATUS; + mode_int |= AVIVO_D1MODE_INT_MASK; + } + if (rdev->irq.crtc_vblank_int[1]) { + tmp |= AVIVO_DISPLAY_INT_STATUS; + mode_int |= AVIVO_D2MODE_INT_MASK; + } + WREG32(RADEON_GEN_INT_CNTL, tmp); + WREG32(AVIVO_DxMODE_INT_MASK, mode_int); + return 0; +} + +static inline uint32_t rs600_irq_ack(struct radeon_device *rdev, u32 *r500_disp_int) +{ + uint32_t irqs = RREG32(RADEON_GEN_INT_STATUS); + uint32_t irq_mask = RADEON_SW_INT_TEST; + + if (irqs & AVIVO_DISPLAY_INT_STATUS) { + *r500_disp_int = RREG32(AVIVO_DISP_INTERRUPT_STATUS); + if (*r500_disp_int & AVIVO_D1_VBLANK_INTERRUPT) { + WREG32(AVIVO_D1MODE_VBLANK_STATUS, AVIVO_VBLANK_ACK); + } + if (*r500_disp_int & AVIVO_D2_VBLANK_INTERRUPT) { + WREG32(AVIVO_D2MODE_VBLANK_STATUS, AVIVO_VBLANK_ACK); + } + } else { + *r500_disp_int = 0; + } + + if (irqs) { + WREG32(RADEON_GEN_INT_STATUS, irqs); + } + return irqs & irq_mask; +} + +int rs600_irq_process(struct radeon_device *rdev) +{ + uint32_t status; + uint32_t r500_disp_int; + + status = rs600_irq_ack(rdev, &r500_disp_int); + if (!status && !r500_disp_int) { + return IRQ_NONE; + } + while (status || r500_disp_int) { + /* SW interrupt */ + if (status & RADEON_SW_INT_TEST) { + radeon_fence_process(rdev); + } + /* Vertical blank interrupts */ + if (r500_disp_int & AVIVO_D1_VBLANK_INTERRUPT) { + drm_handle_vblank(rdev->ddev, 0); + } + if (r500_disp_int & AVIVO_D2_VBLANK_INTERRUPT) { + drm_handle_vblank(rdev->ddev, 1); + } + status = rs600_irq_ack(rdev, &r500_disp_int); + } + return IRQ_HANDLED; +} + +u32 rs600_get_vblank_counter(struct radeon_device *rdev, int crtc) +{ + if (crtc == 0) + return RREG32(AVIVO_D1CRTC_FRAME_COUNT); + else + return RREG32(AVIVO_D2CRTC_FRAME_COUNT); +} + + /* * Global GPU functions */ -- GitLab From de1b28989edff519d0548ebaa3f94fd3d1524cf2 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Wed, 12 Aug 2009 18:43:14 +1000 Subject: [PATCH 1156/1342] drm/radeon/kms: cut down indirects in register accesses. We really don't want to be doing all these indirects, updating the GPU gart table is something we do often so the less overhead the better. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 20 ---------- drivers/gpu/drm/radeon/r300.c | 23 +----------- drivers/gpu/drm/radeon/radeon.h | 51 ++++++++++++++++++++++---- drivers/gpu/drm/radeon/radeon_device.c | 13 ++----- drivers/gpu/drm/radeon/rv515.c | 19 ---------- 5 files changed, 47 insertions(+), 79 deletions(-) diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index e1a6e82b996..90ff8e0ac04 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -1622,26 +1622,6 @@ void r100_pll_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) r100_pll_errata_after_data(rdev); } -uint32_t r100_mm_rreg(struct radeon_device *rdev, uint32_t reg) -{ - if (reg < 0x10000) - return readl(((void __iomem *)rdev->rmmio) + reg); - else { - writel(reg, ((void __iomem *)rdev->rmmio) + RADEON_MM_INDEX); - return readl(((void __iomem *)rdev->rmmio) + RADEON_MM_DATA); - } -} - -void r100_mm_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) -{ - if (reg < 0x10000) - writel(v, ((void __iomem *)rdev->rmmio) + reg); - else { - writel(reg, ((void __iomem *)rdev->rmmio) + RADEON_MM_INDEX); - writel(v, ((void __iomem *)rdev->rmmio) + RADEON_MM_DATA); - } -} - int r100_init(struct radeon_device *rdev) { return 0; diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c index 8594486e162..c47579dcafa 100644 --- a/drivers/gpu/drm/radeon/r300.c +++ b/drivers/gpu/drm/radeon/r300.c @@ -83,8 +83,8 @@ void rv370_pcie_gart_tlb_flush(struct radeon_device *rdev) WREG32_PCIE(RADEON_PCIE_TX_GART_CNTL, tmp | RADEON_PCIE_TX_GART_INVALIDATE_TLB); (void)RREG32_PCIE(RADEON_PCIE_TX_GART_CNTL); WREG32_PCIE(RADEON_PCIE_TX_GART_CNTL, tmp); - mb(); } + mb(); } int rv370_pcie_gart_enable(struct radeon_device *rdev) @@ -592,27 +592,6 @@ void r300_vram_info(struct radeon_device *rdev) } -/* - * Indirect registers accessor - */ -uint32_t rv370_pcie_rreg(struct radeon_device *rdev, uint32_t reg) -{ - uint32_t r; - - WREG8(RADEON_PCIE_INDEX, ((reg) & 0xff)); - (void)RREG32(RADEON_PCIE_INDEX); - r = RREG32(RADEON_PCIE_DATA); - return r; -} - -void rv370_pcie_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) -{ - WREG8(RADEON_PCIE_INDEX, ((reg) & 0xff)); - (void)RREG32(RADEON_PCIE_INDEX); - WREG32(RADEON_PCIE_DATA, (v)); - (void)RREG32(RADEON_PCIE_DATA); -} - /* * PCIE Lanes */ diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index 34611274084..87170a56e37 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -667,14 +667,11 @@ struct radeon_device { resource_size_t rmmio_base; resource_size_t rmmio_size; void *rmmio; - radeon_rreg_t mm_rreg; - radeon_wreg_t mm_wreg; radeon_rreg_t mc_rreg; radeon_wreg_t mc_wreg; radeon_rreg_t pll_rreg; radeon_wreg_t pll_wreg; - radeon_rreg_t pcie_rreg; - radeon_wreg_t pcie_wreg; + uint32_t pcie_reg_mask; radeon_rreg_t pciep_rreg; radeon_wreg_t pciep_wreg; struct radeon_clock clock; @@ -706,22 +703,42 @@ int radeon_device_init(struct radeon_device *rdev, void radeon_device_fini(struct radeon_device *rdev); int radeon_gpu_wait_for_idle(struct radeon_device *rdev); +static inline uint32_t r100_mm_rreg(struct radeon_device *rdev, uint32_t reg) +{ + if (reg < 0x10000) + return readl(((void __iomem *)rdev->rmmio) + reg); + else { + writel(reg, ((void __iomem *)rdev->rmmio) + RADEON_MM_INDEX); + return readl(((void __iomem *)rdev->rmmio) + RADEON_MM_DATA); + } +} + +static inline void r100_mm_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) +{ + if (reg < 0x10000) + writel(v, ((void __iomem *)rdev->rmmio) + reg); + else { + writel(reg, ((void __iomem *)rdev->rmmio) + RADEON_MM_INDEX); + writel(v, ((void __iomem *)rdev->rmmio) + RADEON_MM_DATA); + } +} + /* * Registers read & write functions. */ #define RREG8(reg) readb(((void __iomem *)rdev->rmmio) + (reg)) #define WREG8(reg, v) writeb(v, ((void __iomem *)rdev->rmmio) + (reg)) -#define RREG32(reg) rdev->mm_rreg(rdev, (reg)) -#define WREG32(reg, v) rdev->mm_wreg(rdev, (reg), (v)) +#define RREG32(reg) r100_mm_rreg(rdev, (reg)) +#define WREG32(reg, v) r100_mm_wreg(rdev, (reg), (v)) #define REG_SET(FIELD, v) (((v) << FIELD##_SHIFT) & FIELD##_MASK) #define REG_GET(FIELD, v) (((v) << FIELD##_SHIFT) & FIELD##_MASK) #define RREG32_PLL(reg) rdev->pll_rreg(rdev, (reg)) #define WREG32_PLL(reg, v) rdev->pll_wreg(rdev, (reg), (v)) #define RREG32_MC(reg) rdev->mc_rreg(rdev, (reg)) #define WREG32_MC(reg, v) rdev->mc_wreg(rdev, (reg), (v)) -#define RREG32_PCIE(reg) rdev->pcie_rreg(rdev, (reg)) -#define WREG32_PCIE(reg, v) rdev->pcie_wreg(rdev, (reg), (v)) +#define RREG32_PCIE(reg) rv370_pcie_rreg(rdev, (reg)) +#define WREG32_PCIE(reg, v) rv370_pcie_wreg(rdev, (reg), (v)) #define WREG32_P(reg, val, mask) \ do { \ uint32_t tmp_ = RREG32(reg); \ @@ -737,6 +754,24 @@ int radeon_gpu_wait_for_idle(struct radeon_device *rdev); WREG32_PLL(reg, tmp_); \ } while (0) +/* + * Indirect registers accessor + */ +static inline uint32_t rv370_pcie_rreg(struct radeon_device *rdev, uint32_t reg) +{ + uint32_t r; + + WREG32(RADEON_PCIE_INDEX, ((reg) & rdev->pcie_reg_mask)); + r = RREG32(RADEON_PCIE_DATA); + return r; +} + +static inline void rv370_pcie_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) +{ + WREG32(RADEON_PCIE_INDEX, ((reg) & rdev->pcie_reg_mask)); + WREG32(RADEON_PCIE_DATA, (v)); +} + void r100_pll_errata_after_index(struct radeon_device *rdev); diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c index 9ff6dcb97f9..7693f7c67bd 100644 --- a/drivers/gpu/drm/radeon/radeon_device.c +++ b/drivers/gpu/drm/radeon/radeon_device.c @@ -225,25 +225,18 @@ void radeon_invalid_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) void radeon_register_accessor_init(struct radeon_device *rdev) { - rdev->mm_rreg = &r100_mm_rreg; - rdev->mm_wreg = &r100_mm_wreg; rdev->mc_rreg = &radeon_invalid_rreg; rdev->mc_wreg = &radeon_invalid_wreg; rdev->pll_rreg = &radeon_invalid_rreg; rdev->pll_wreg = &radeon_invalid_wreg; - rdev->pcie_rreg = &radeon_invalid_rreg; - rdev->pcie_wreg = &radeon_invalid_wreg; rdev->pciep_rreg = &radeon_invalid_rreg; rdev->pciep_wreg = &radeon_invalid_wreg; /* Don't change order as we are overridding accessor. */ if (rdev->family < CHIP_RV515) { - rdev->pcie_rreg = &rv370_pcie_rreg; - rdev->pcie_wreg = &rv370_pcie_wreg; - } - if (rdev->family >= CHIP_RV515) { - rdev->pcie_rreg = &rv515_pcie_rreg; - rdev->pcie_wreg = &rv515_pcie_wreg; + rdev->pcie_reg_mask = 0xff; + } else { + rdev->pcie_reg_mask = 0x7ff; } /* FIXME: not sure here */ if (rdev->family <= CHIP_R580) { diff --git a/drivers/gpu/drm/radeon/rv515.c b/drivers/gpu/drm/radeon/rv515.c index fd8f3ca716e..31a7f668ae5 100644 --- a/drivers/gpu/drm/radeon/rv515.c +++ b/drivers/gpu/drm/radeon/rv515.c @@ -400,25 +400,6 @@ void rv515_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) WREG32(MC_IND_INDEX, 0); } -uint32_t rv515_pcie_rreg(struct radeon_device *rdev, uint32_t reg) -{ - uint32_t r; - - WREG32(PCIE_INDEX, ((reg) & 0x7ff)); - (void)RREG32(PCIE_INDEX); - r = RREG32(PCIE_DATA); - return r; -} - -void rv515_pcie_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) -{ - WREG32(PCIE_INDEX, ((reg) & 0x7ff)); - (void)RREG32(PCIE_INDEX); - WREG32(PCIE_DATA, (v)); - (void)RREG32(PCIE_DATA); -} - - /* * Debugfs info */ -- GitLab From b2add73dbf93fd50f00564d7abc3e2b9aa9dd20c Mon Sep 17 00:00:00 2001 From: Guillaume Knispel Date: Sat, 15 Aug 2009 19:30:24 +0200 Subject: [PATCH 1157/1342] poll/select: initialize triggered field of struct poll_wqueues The triggered field of struct poll_wqueues introduced in commit 5f820f648c92a5ecc771a96b3c29aa6e90013bba ("poll: allow f_op->poll to sleep"). It was first set to 1 in pollwake() (now __pollwake() ), tested and later set to 0 in poll_schedule_timeout(), but not initialized before. As a result when the process needs to sleep, triggered was likely to be non-zero even if pollwake() is not called before the first poll_schedule_timeout(), meaning schedule_hrtimeout_range() would not be called and an extra loop calling all ->poll() would be done. This patch initialize triggered to 0 in poll_initwait() so the ->poll() are not called twice before the process goes to sleep when it needs to. Signed-off-by: Guillaume Knispel Acked-by: Thomas Gleixner Acked-by: Tejun Heo Cc: stable@kernel.org Signed-off-by: Linus Torvalds --- fs/select.c | 1 + 1 file changed, 1 insertion(+) diff --git a/fs/select.c b/fs/select.c index d870237e42c..8084834e123 100644 --- a/fs/select.c +++ b/fs/select.c @@ -110,6 +110,7 @@ void poll_initwait(struct poll_wqueues *pwq) { init_poll_funcptr(&pwq->pt, __pollwait); pwq->polling_task = current; + pwq->triggered = 0; pwq->error = 0; pwq->table = NULL; pwq->inline_index = 0; -- GitLab From 64c6460875957502541a4ba30835ac625a0bee79 Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Fri, 14 Aug 2009 15:49:43 +0000 Subject: [PATCH 1158/1342] cnic: Fix symbol_put_addr() panic on ia64. When the cnic driver tries to grab a symbol from bnx2 when bnx2 is running init code, symbol_get() will succeed but symbol_put_addr() will hit BUG() a moment later. module_text_address() fails because bnx2 is still in init code. This is fixed by using symbol_put() instead which does the exact opposite of symbol_get(). Signed-off-by: Michael Chan Signed-off-by: David S. Miller --- drivers/net/cnic.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/cnic.c b/drivers/net/cnic.c index 4869d77cbe9..ecde186fccd 100644 --- a/drivers/net/cnic.c +++ b/drivers/net/cnic.c @@ -2543,7 +2543,7 @@ static struct cnic_dev *init_bnx2_cnic(struct net_device *dev) probe = symbol_get(bnx2_cnic_probe); if (probe) { ethdev = (*probe)(dev); - symbol_put_addr(probe); + symbol_put(bnx2_cnic_probe); } if (!ethdev) return NULL; -- GitLab From a3059b12adae868c42629ecf058a94195ef1e958 Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Fri, 14 Aug 2009 15:49:44 +0000 Subject: [PATCH 1159/1342] cnic: Refine registration with bnx2. Register and unregister with bnx2 during NETDEV_UP and NETDEV_DOWN events. This simplifies the sequence of events and allows locking fixes in the next patch. Signed-off-by: Michael Chan Reviewed-by: Benjamin Li Signed-off-by: David S. Miller --- drivers/net/cnic.c | 49 ++++++++++++++++++++++++++++++++++------------ 1 file changed, 36 insertions(+), 13 deletions(-) diff --git a/drivers/net/cnic.c b/drivers/net/cnic.c index ecde186fccd..2db81f0e4f7 100644 --- a/drivers/net/cnic.c +++ b/drivers/net/cnic.c @@ -2393,21 +2393,45 @@ static int cnic_start_bnx2_hw(struct cnic_dev *dev) return 0; } -static int cnic_start_hw(struct cnic_dev *dev) +static int cnic_register_netdev(struct cnic_dev *dev) { struct cnic_local *cp = dev->cnic_priv; struct cnic_eth_dev *ethdev = cp->ethdev; int err; - if (test_bit(CNIC_F_CNIC_UP, &dev->flags)) - return -EALREADY; + if (!ethdev) + return -ENODEV; + + if (ethdev->drv_state & CNIC_DRV_STATE_REGD) + return 0; err = ethdev->drv_register_cnic(dev->netdev, cp->cnic_ops, dev); - if (err) { + if (err) printk(KERN_ERR PFX "%s: register_cnic failed\n", dev->netdev->name); - goto err2; - } + + return err; +} + +static void cnic_unregister_netdev(struct cnic_dev *dev) +{ + struct cnic_local *cp = dev->cnic_priv; + struct cnic_eth_dev *ethdev = cp->ethdev; + + if (!ethdev) + return; + + ethdev->drv_unregister_cnic(dev->netdev); +} + +static int cnic_start_hw(struct cnic_dev *dev) +{ + struct cnic_local *cp = dev->cnic_priv; + struct cnic_eth_dev *ethdev = cp->ethdev; + int err; + + if (test_bit(CNIC_F_CNIC_UP, &dev->flags)) + return -EALREADY; dev->regview = ethdev->io_base; cp->chip_id = ethdev->chip_id; @@ -2438,18 +2462,13 @@ static int cnic_start_hw(struct cnic_dev *dev) return 0; err1: - ethdev->drv_unregister_cnic(dev->netdev); cp->free_resc(dev); pci_dev_put(dev->pcidev); -err2: return err; } static void cnic_stop_bnx2_hw(struct cnic_dev *dev) { - struct cnic_local *cp = dev->cnic_priv; - struct cnic_eth_dev *ethdev = cp->ethdev; - cnic_disable_bnx2_int_sync(dev); cnic_reg_wr_ind(dev, BNX2_CP_SCRATCH + 0x20, 0); @@ -2461,8 +2480,6 @@ static void cnic_stop_bnx2_hw(struct cnic_dev *dev) cnic_setup_5709_context(dev, 0); cnic_free_irq(dev); - ethdev->drv_unregister_cnic(dev->netdev); - cnic_free_resc(dev); } @@ -2646,6 +2663,10 @@ static int cnic_netdev_event(struct notifier_block *this, unsigned long event, else if (event == NETDEV_UNREGISTER) cnic_ulp_exit(dev); else if (event == NETDEV_UP) { + if (cnic_register_netdev(dev) != 0) { + cnic_put(dev); + goto done; + } mutex_lock(&cnic_lock); if (!cnic_start_hw(dev)) cnic_ulp_start(dev); @@ -2672,6 +2693,7 @@ static int cnic_netdev_event(struct notifier_block *this, unsigned long event, cnic_ulp_stop(dev); cnic_stop_hw(dev); mutex_unlock(&cnic_lock); + cnic_unregister_netdev(dev); } else if (event == NETDEV_UNREGISTER) { write_lock(&cnic_dev_lock); list_del_init(&dev->list); @@ -2703,6 +2725,7 @@ static void cnic_release(void) } cnic_ulp_exit(dev); + cnic_unregister_netdev(dev); list_del_init(&dev->list); cnic_free_dev(dev); } -- GitLab From c5a889508203446c1abc1d670599b3a816841813 Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Fri, 14 Aug 2009 15:49:45 +0000 Subject: [PATCH 1160/1342] bnx2: Use mutex on slow path cnic calls. The slow path calls to the cnic driver are sleepable calls so we cannot use rcu_read_lock(). Use mutex for these slow path calls instead. Signed-off-by: Michael Chan Reviewed-by: Benjamin Li Signed-off-by: David S. Miller --- drivers/net/bnx2.c | 17 +++++++++++------ drivers/net/bnx2.h | 1 + 2 files changed, 12 insertions(+), 6 deletions(-) diff --git a/drivers/net/bnx2.c b/drivers/net/bnx2.c index b70cc99962f..06b901152d4 100644 --- a/drivers/net/bnx2.c +++ b/drivers/net/bnx2.c @@ -399,9 +399,11 @@ static int bnx2_unregister_cnic(struct net_device *dev) struct bnx2_napi *bnapi = &bp->bnx2_napi[0]; struct cnic_eth_dev *cp = &bp->cnic_eth_dev; + mutex_lock(&bp->cnic_lock); cp->drv_state = 0; bnapi->cnic_present = 0; rcu_assign_pointer(bp->cnic_ops, NULL); + mutex_unlock(&bp->cnic_lock); synchronize_rcu(); return 0; } @@ -429,13 +431,13 @@ bnx2_cnic_stop(struct bnx2 *bp) struct cnic_ops *c_ops; struct cnic_ctl_info info; - rcu_read_lock(); - c_ops = rcu_dereference(bp->cnic_ops); + mutex_lock(&bp->cnic_lock); + c_ops = bp->cnic_ops; if (c_ops) { info.cmd = CNIC_CTL_STOP_CMD; c_ops->cnic_ctl(bp->cnic_data, &info); } - rcu_read_unlock(); + mutex_unlock(&bp->cnic_lock); } static void @@ -444,8 +446,8 @@ bnx2_cnic_start(struct bnx2 *bp) struct cnic_ops *c_ops; struct cnic_ctl_info info; - rcu_read_lock(); - c_ops = rcu_dereference(bp->cnic_ops); + mutex_lock(&bp->cnic_lock); + c_ops = bp->cnic_ops; if (c_ops) { if (!(bp->flags & BNX2_FLAG_USING_MSIX)) { struct bnx2_napi *bnapi = &bp->bnx2_napi[0]; @@ -455,7 +457,7 @@ bnx2_cnic_start(struct bnx2 *bp) info.cmd = CNIC_CTL_START_CMD; c_ops->cnic_ctl(bp->cnic_data, &info); } - rcu_read_unlock(); + mutex_unlock(&bp->cnic_lock); } #else @@ -7663,6 +7665,9 @@ bnx2_init_board(struct pci_dev *pdev, struct net_device *dev) spin_lock_init(&bp->phy_lock); spin_lock_init(&bp->indirect_lock); +#ifdef BCM_CNIC + mutex_init(&bp->cnic_lock); +#endif INIT_WORK(&bp->reset_task, bnx2_reset_task); dev->base_addr = dev->mem_start = pci_resource_start(pdev, 0); diff --git a/drivers/net/bnx2.h b/drivers/net/bnx2.h index f1edfaa9e56..a4f12fd0ecd 100644 --- a/drivers/net/bnx2.h +++ b/drivers/net/bnx2.h @@ -6902,6 +6902,7 @@ struct bnx2 { u32 idle_chk_status_idx; #ifdef BCM_CNIC + struct mutex cnic_lock; struct cnic_eth_dev cnic_eth_dev; #endif -- GitLab From 681dbd710779e8b8d5bae926f6b11f30df70638b Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Fri, 14 Aug 2009 15:49:46 +0000 Subject: [PATCH 1161/1342] cnic: Fix locking in start/stop calls. The slow path ulp_start and ulp_stop calls to the bnx2i driver are sleepable calls and therefore should not be protected using rcu_read_lock. Fix it by using mutex and setting a bit during these calls. cnic_unregister_device() will now wait for the bit to clear before completing the call. Signed-off-by: Michael Chan Reviewed-by: Benjamin Li Signed-off-by: David S. Miller --- drivers/net/cnic.c | 44 ++++++++++++++++++++++++++++---------------- drivers/net/cnic.h | 1 + 2 files changed, 29 insertions(+), 16 deletions(-) diff --git a/drivers/net/cnic.c b/drivers/net/cnic.c index 2db81f0e4f7..4ff618a7afd 100644 --- a/drivers/net/cnic.c +++ b/drivers/net/cnic.c @@ -466,6 +466,7 @@ EXPORT_SYMBOL(cnic_register_driver); static int cnic_unregister_device(struct cnic_dev *dev, int ulp_type) { struct cnic_local *cp = dev->cnic_priv; + int i = 0; if (ulp_type >= MAX_CNIC_ULP_TYPE) { printk(KERN_ERR PFX "cnic_unregister_device: Bad type %d\n", @@ -486,6 +487,15 @@ static int cnic_unregister_device(struct cnic_dev *dev, int ulp_type) synchronize_rcu(); + while (test_bit(ULP_F_CALL_PENDING, &cp->ulp_flags[ulp_type]) && + i < 20) { + msleep(100); + i++; + } + if (test_bit(ULP_F_CALL_PENDING, &cp->ulp_flags[ulp_type])) + printk(KERN_WARNING PFX "%s: Failed waiting for ULP up call" + " to complete.\n", dev->netdev->name); + return 0; } EXPORT_SYMBOL(cnic_unregister_driver); @@ -1076,18 +1086,23 @@ static void cnic_ulp_stop(struct cnic_dev *dev) if (cp->cnic_uinfo) cnic_send_nlmsg(cp, ISCSI_KEVENT_IF_DOWN, NULL); - rcu_read_lock(); for (if_type = 0; if_type < MAX_CNIC_ULP_TYPE; if_type++) { struct cnic_ulp_ops *ulp_ops; - ulp_ops = rcu_dereference(cp->ulp_ops[if_type]); - if (!ulp_ops) + mutex_lock(&cnic_lock); + ulp_ops = cp->ulp_ops[if_type]; + if (!ulp_ops) { + mutex_unlock(&cnic_lock); continue; + } + set_bit(ULP_F_CALL_PENDING, &cp->ulp_flags[if_type]); + mutex_unlock(&cnic_lock); if (test_and_clear_bit(ULP_F_START, &cp->ulp_flags[if_type])) ulp_ops->cnic_stop(cp->ulp_handle[if_type]); + + clear_bit(ULP_F_CALL_PENDING, &cp->ulp_flags[if_type]); } - rcu_read_unlock(); } static void cnic_ulp_start(struct cnic_dev *dev) @@ -1095,18 +1110,23 @@ static void cnic_ulp_start(struct cnic_dev *dev) struct cnic_local *cp = dev->cnic_priv; int if_type; - rcu_read_lock(); for (if_type = 0; if_type < MAX_CNIC_ULP_TYPE; if_type++) { struct cnic_ulp_ops *ulp_ops; - ulp_ops = rcu_dereference(cp->ulp_ops[if_type]); - if (!ulp_ops || !ulp_ops->cnic_start) + mutex_lock(&cnic_lock); + ulp_ops = cp->ulp_ops[if_type]; + if (!ulp_ops || !ulp_ops->cnic_start) { + mutex_unlock(&cnic_lock); continue; + } + set_bit(ULP_F_CALL_PENDING, &cp->ulp_flags[if_type]); + mutex_unlock(&cnic_lock); if (!test_and_set_bit(ULP_F_START, &cp->ulp_flags[if_type])) ulp_ops->cnic_start(cp->ulp_handle[if_type]); + + clear_bit(ULP_F_CALL_PENDING, &cp->ulp_flags[if_type]); } - rcu_read_unlock(); } static int cnic_ctl(void *data, struct cnic_ctl_info *info) @@ -1116,22 +1136,18 @@ static int cnic_ctl(void *data, struct cnic_ctl_info *info) switch (info->cmd) { case CNIC_CTL_STOP_CMD: cnic_hold(dev); - mutex_lock(&cnic_lock); cnic_ulp_stop(dev); cnic_stop_hw(dev); - mutex_unlock(&cnic_lock); cnic_put(dev); break; case CNIC_CTL_START_CMD: cnic_hold(dev); - mutex_lock(&cnic_lock); if (!cnic_start_hw(dev)) cnic_ulp_start(dev); - mutex_unlock(&cnic_lock); cnic_put(dev); break; default: @@ -2667,10 +2683,8 @@ static int cnic_netdev_event(struct notifier_block *this, unsigned long event, cnic_put(dev); goto done; } - mutex_lock(&cnic_lock); if (!cnic_start_hw(dev)) cnic_ulp_start(dev); - mutex_unlock(&cnic_lock); } rcu_read_lock(); @@ -2689,10 +2703,8 @@ static int cnic_netdev_event(struct notifier_block *this, unsigned long event, rcu_read_unlock(); if (event == NETDEV_GOING_DOWN) { - mutex_lock(&cnic_lock); cnic_ulp_stop(dev); cnic_stop_hw(dev); - mutex_unlock(&cnic_lock); cnic_unregister_netdev(dev); } else if (event == NETDEV_UNREGISTER) { write_lock(&cnic_dev_lock); diff --git a/drivers/net/cnic.h b/drivers/net/cnic.h index 5192d4a9df5..a94b302bb46 100644 --- a/drivers/net/cnic.h +++ b/drivers/net/cnic.h @@ -176,6 +176,7 @@ struct cnic_local { unsigned long ulp_flags[MAX_CNIC_ULP_TYPE]; #define ULP_F_INIT 0 #define ULP_F_START 1 +#define ULP_F_CALL_PENDING 2 struct cnic_ulp_ops *ulp_ops[MAX_CNIC_ULP_TYPE]; /* protected by ulp_lock */ -- GitLab From 7fc1ece40704b150477e548a7a98d285cc418790 Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Fri, 14 Aug 2009 15:49:47 +0000 Subject: [PATCH 1162/1342] cnic: Fix locking in init/exit calls. The slow path ulp_init and ulp_exit calls to the bnx2i driver are sleepable calls and therefore should not be protected using rcu_read_lock. Fix it by using mutex and refcount during these calls. cnic_unregister_driver() will now wait for the refcount to go to zero before completing the call. Signed-off-by: Michael Chan Reviewed-by: Benjamin Li Signed-off-by: David S. Miller --- drivers/net/cnic.c | 48 +++++++++++++++++++++++++++++++++++-------- drivers/net/cnic_if.h | 1 + 2 files changed, 40 insertions(+), 9 deletions(-) diff --git a/drivers/net/cnic.c b/drivers/net/cnic.c index 4ff618a7afd..74c342959b7 100644 --- a/drivers/net/cnic.c +++ b/drivers/net/cnic.c @@ -138,6 +138,16 @@ static struct cnic_dev *cnic_from_netdev(struct net_device *netdev) return NULL; } +static inline void ulp_get(struct cnic_ulp_ops *ulp_ops) +{ + atomic_inc(&ulp_ops->ref_count); +} + +static inline void ulp_put(struct cnic_ulp_ops *ulp_ops) +{ + atomic_dec(&ulp_ops->ref_count); +} + static void cnic_ctx_wr(struct cnic_dev *dev, u32 cid_addr, u32 off, u32 val) { struct cnic_local *cp = dev->cnic_priv; @@ -358,6 +368,7 @@ int cnic_register_driver(int ulp_type, struct cnic_ulp_ops *ulp_ops) } read_unlock(&cnic_dev_lock); + atomic_set(&ulp_ops->ref_count, 0); rcu_assign_pointer(cnic_ulp_tbl[ulp_type], ulp_ops); mutex_unlock(&cnic_lock); @@ -379,6 +390,8 @@ int cnic_register_driver(int ulp_type, struct cnic_ulp_ops *ulp_ops) int cnic_unregister_driver(int ulp_type) { struct cnic_dev *dev; + struct cnic_ulp_ops *ulp_ops; + int i = 0; if (ulp_type >= MAX_CNIC_ULP_TYPE) { printk(KERN_ERR PFX "cnic_unregister_driver: Bad type %d\n", @@ -386,7 +399,8 @@ int cnic_unregister_driver(int ulp_type) return -EINVAL; } mutex_lock(&cnic_lock); - if (!cnic_ulp_tbl[ulp_type]) { + ulp_ops = cnic_ulp_tbl[ulp_type]; + if (!ulp_ops) { printk(KERN_ERR PFX "cnic_unregister_driver: Type %d has not " "been registered\n", ulp_type); goto out_unlock; @@ -411,6 +425,14 @@ int cnic_unregister_driver(int ulp_type) mutex_unlock(&cnic_lock); synchronize_rcu(); + while ((atomic_read(&ulp_ops->ref_count) != 0) && (i < 20)) { + msleep(100); + i++; + } + + if (atomic_read(&ulp_ops->ref_count) != 0) + printk(KERN_WARNING PFX "%s: Failed waiting for ref count to go" + " to zero.\n", dev->netdev->name); return 0; out_unlock: @@ -1161,19 +1183,23 @@ static void cnic_ulp_init(struct cnic_dev *dev) int i; struct cnic_local *cp = dev->cnic_priv; - rcu_read_lock(); for (i = 0; i < MAX_CNIC_ULP_TYPE_EXT; i++) { struct cnic_ulp_ops *ulp_ops; - ulp_ops = rcu_dereference(cnic_ulp_tbl[i]); - if (!ulp_ops || !ulp_ops->cnic_init) + mutex_lock(&cnic_lock); + ulp_ops = cnic_ulp_tbl[i]; + if (!ulp_ops || !ulp_ops->cnic_init) { + mutex_unlock(&cnic_lock); continue; + } + ulp_get(ulp_ops); + mutex_unlock(&cnic_lock); if (!test_and_set_bit(ULP_F_INIT, &cp->ulp_flags[i])) ulp_ops->cnic_init(dev); + ulp_put(ulp_ops); } - rcu_read_unlock(); } static void cnic_ulp_exit(struct cnic_dev *dev) @@ -1181,19 +1207,23 @@ static void cnic_ulp_exit(struct cnic_dev *dev) int i; struct cnic_local *cp = dev->cnic_priv; - rcu_read_lock(); for (i = 0; i < MAX_CNIC_ULP_TYPE_EXT; i++) { struct cnic_ulp_ops *ulp_ops; - ulp_ops = rcu_dereference(cnic_ulp_tbl[i]); - if (!ulp_ops || !ulp_ops->cnic_exit) + mutex_lock(&cnic_lock); + ulp_ops = cnic_ulp_tbl[i]; + if (!ulp_ops || !ulp_ops->cnic_exit) { + mutex_unlock(&cnic_lock); continue; + } + ulp_get(ulp_ops); + mutex_unlock(&cnic_lock); if (test_and_clear_bit(ULP_F_INIT, &cp->ulp_flags[i])) ulp_ops->cnic_exit(dev); + ulp_put(ulp_ops); } - rcu_read_unlock(); } static int cnic_cm_offload_pg(struct cnic_sock *csk) diff --git a/drivers/net/cnic_if.h b/drivers/net/cnic_if.h index d1bce27ee99..a49235739ee 100644 --- a/drivers/net/cnic_if.h +++ b/drivers/net/cnic_if.h @@ -290,6 +290,7 @@ struct cnic_ulp_ops { void (*iscsi_nl_send_msg)(struct cnic_dev *dev, u32 msg_type, char *data, u16 data_size); struct module *owner; + atomic_t ref_count; }; extern int cnic_register_driver(int ulp_type, struct cnic_ulp_ops *ulp_ops); -- GitLab From 82776a4bcd7aa5fbcd2e6339b3ce88b727dd40ab Mon Sep 17 00:00:00 2001 From: Bruce Allan Date: Fri, 14 Aug 2009 14:35:33 +0000 Subject: [PATCH 1163/1342] e1000e: WoL does not work on 82577/82578 with manageability enabled With manageability (Intel AMT) enabled via BIOS, PHY wakeup does not get configured on newer parts which use PHY wakeup vs. MAC wakeup which causes WoL to not work. The driver should configure PHY wakeup whether or not manageability is enabled. Signed-off-by: Bruce Allan Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/e1000e/netdev.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c index 63415bb6f48..58e22fcb22b 100644 --- a/drivers/net/e1000e/netdev.c +++ b/drivers/net/e1000e/netdev.c @@ -4538,8 +4538,7 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake) /* Allow time for pending master requests to run */ e1000e_disable_pcie_master(&adapter->hw); - if ((adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) && - !(hw->mac.ops.check_mng_mode(hw))) { + if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) { /* enable wakeup by the PHY */ retval = e1000_init_phy_wakeup(adapter, wufc); if (retval) @@ -4557,7 +4556,8 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake) *enable_wake = !!wufc; /* make sure adapter isn't asleep if manageability is enabled */ - if (adapter->flags & FLAG_MNG_PT_ENABLED) + if ((adapter->flags & FLAG_MNG_PT_ENABLED) || + (hw->mac.ops.check_mng_mode(hw))) *enable_wake = true; if (adapter->hw.phy.type == e1000_phy_igp_3) -- GitLab From 68eac4602b9104cdaa6c18b3edd914cececa6a1e Mon Sep 17 00:00:00 2001 From: Xiaotian Feng Date: Fri, 14 Aug 2009 14:35:52 +0000 Subject: [PATCH 1164/1342] e1000e: fix use of pci_enable_pcie_error_reporting commit 111b9dc5 ("e1000e: add aer support") introduces pcie aer support for e1000e, but it is not reasonable to disable it in e1000_remove but enable it in e1000_resume. This patch enables aer support in e1000_probe. Signed-off-by: Xiaotian Feng Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/e1000e/netdev.c | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c index 58e22fcb22b..fa92a683aef 100644 --- a/drivers/net/e1000e/netdev.c +++ b/drivers/net/e1000e/netdev.c @@ -4670,14 +4670,6 @@ static int e1000_resume(struct pci_dev *pdev) return err; } - /* AER (Advanced Error Reporting) hooks */ - err = pci_enable_pcie_error_reporting(pdev); - if (err) { - dev_err(&pdev->dev, "pci_enable_pcie_error_reporting failed " - "0x%x\n", err); - /* non-fatal, continue */ - } - pci_set_master(pdev); pci_enable_wake(pdev, PCI_D3hot, 0); @@ -4990,6 +4982,14 @@ static int __devinit e1000_probe(struct pci_dev *pdev, if (err) goto err_pci_reg; + /* AER (Advanced Error Reporting) hooks */ + err = pci_enable_pcie_error_reporting(pdev); + if (err) { + dev_err(&pdev->dev, "pci_enable_pcie_error_reporting failed " + "0x%x\n", err); + /* non-fatal, continue */ + } + pci_set_master(pdev); /* PCI config space info */ err = pci_save_state(pdev); -- GitLab From 4e5c25d405e18a2f279ca2bfc855508ec3a0186b Mon Sep 17 00:00:00 2001 From: Hugh Dickins Date: Sun, 16 Aug 2009 15:54:37 +0100 Subject: [PATCH 1165/1342] x86, mce: therm_throt: Don't log redundant normality 0d01f31439c1e4d602bf9fdc924ab66f407f5e38 "x86, mce: therm_throt - change when we print messages" removed redundant announcements of "Temperature/speed normal". They're not worth logging and remove their accompanying "Machine check events logged" messages as well from the console. Signed-off-by: Hugh Dickins Cc: Hidetoshi Seto Cc: Andi Kleen Cc: Dmitry Torokhov LKML-Reference: Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/mcheck/therm_throt.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) diff --git a/arch/x86/kernel/cpu/mcheck/therm_throt.c b/arch/x86/kernel/cpu/mcheck/therm_throt.c index 8bc64cfbe93..5957a93e517 100644 --- a/arch/x86/kernel/cpu/mcheck/therm_throt.c +++ b/arch/x86/kernel/cpu/mcheck/therm_throt.c @@ -116,11 +116,14 @@ static int therm_throt_process(int curr) cpu, __get_cpu_var(thermal_throttle_count)); add_taint(TAINT_MACHINE_CHECK); - } else if (was_throttled) { + return 1; + } + if (was_throttled) { printk(KERN_INFO "CPU%d: Temperature/speed normal\n", cpu); + return 1; } - return 1; + return 0; } #ifdef CONFIG_SYSFS -- GitLab From 894ef820b10d77e2d6d717342fc408bdd9825139 Mon Sep 17 00:00:00 2001 From: Randy Dunlap Date: Sun, 16 Aug 2009 07:33:30 -0700 Subject: [PATCH 1166/1342] dm-log-userspace: fix printk format warning drivers/md/dm-log-userspace-transfer.c:110: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'size_t' Previously posted and acked, but apparently lost. http://lkml.indiana.edu/hypermail/linux/kernel/0906.2/02074.html Signed-off-by: Randy Dunlap Cc: dm-devel@redhat.com Signed-off-by: Linus Torvalds --- drivers/md/dm-log-userspace-transfer.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/md/dm-log-userspace-transfer.c b/drivers/md/dm-log-userspace-transfer.c index 0ca1ee768a1..8ce74d95ae4 100644 --- a/drivers/md/dm-log-userspace-transfer.c +++ b/drivers/md/dm-log-userspace-transfer.c @@ -108,7 +108,7 @@ static int fill_pkg(struct cn_msg *msg, struct dm_ulog_request *tfr) *(pkg->data_size) = 0; } else if (tfr->data_size > *(pkg->data_size)) { DMERR("Insufficient space to receive package [%u] " - "(%u vs %lu)", tfr->request_type, + "(%u vs %zu)", tfr->request_type, tfr->data_size, *(pkg->data_size)); *(pkg->data_size) = 0; -- GitLab From 52459ab91363343af8ae252766e9da762344a2e7 Mon Sep 17 00:00:00 2001 From: Leonardo Potenza Date: Sun, 16 Aug 2009 18:55:48 +0200 Subject: [PATCH 1167/1342] x86: Annotate section mismatch warnings in kernel/apic/x2apic_uv_x.c The function uv_acpi_madt_oem_check() has been marked __init, the struct apic_x2apic_uv_x has been marked __refdata. The aim is to address the following section mismatch messages: WARNING: arch/x86/kernel/apic/built-in.o(.data+0x1368): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary() The variable apic_x2apic_uv_x references the function __cpuinit uv_wakeup_secondary() If the reference is valid then annotate the variable with __init* or __refdata (see linux/init.h) or name the variable: *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, WARNING: arch/x86/kernel/built-in.o(.data+0x68e8): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary() The variable apic_x2apic_uv_x references the function __cpuinit uv_wakeup_secondary() If the reference is valid then annotate the variable with __init* or __refdata (see linux/init.h) or name the variable: *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, WARNING: arch/x86/built-in.o(.text+0x7b36f): Section mismatch in reference from the function uv_acpi_madt_oem_check() to the function .init.text:early_ioremap() The function uv_acpi_madt_oem_check() references the function __init early_ioremap(). This is often because uv_acpi_madt_oem_check lacks a __init annotation or the annotation of early_ioremap is wrong. WARNING: arch/x86/built-in.o(.text+0x7b38d): Section mismatch in reference from the function uv_acpi_madt_oem_check() to the function .init.text:early_iounmap() The function uv_acpi_madt_oem_check() references the function __init early_iounmap(). This is often because uv_acpi_madt_oem_check lacks a __init annotation or the annotation of early_iounmap is wrong. WARNING: arch/x86/built-in.o(.data+0x8668): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary() The variable apic_x2apic_uv_x references the function __cpuinit uv_wakeup_secondary() If the reference is valid then annotate the variable with __init* or __refdata (see linux/init.h) or name the variable: *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, Signed-off-by: Leonardo Potenza LKML-Reference: <200908161855.48302.lpotenza@inwind.it> Signed-off-by: Ingo Molnar --- arch/x86/kernel/apic/x2apic_uv_x.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/x86/kernel/apic/x2apic_uv_x.c b/arch/x86/kernel/apic/x2apic_uv_x.c index 832e908adcb..601159374e8 100644 --- a/arch/x86/kernel/apic/x2apic_uv_x.c +++ b/arch/x86/kernel/apic/x2apic_uv_x.c @@ -46,7 +46,7 @@ static int early_get_nodeid(void) return node_id.s.node_id; } -static int uv_acpi_madt_oem_check(char *oem_id, char *oem_table_id) +static int __init uv_acpi_madt_oem_check(char *oem_id, char *oem_table_id) { if (!strcmp(oem_id, "SGI")) { if (!strcmp(oem_table_id, "UVL")) @@ -253,7 +253,7 @@ static void uv_send_IPI_self(int vector) apic_write(APIC_SELF_IPI, vector); } -struct apic apic_x2apic_uv_x = { +struct apic __refdata apic_x2apic_uv_x = { .name = "UV large system", .probe = NULL, -- GitLab From cefb87efc9aa0288849149484870d5ab989fbd59 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Sun, 16 Aug 2009 21:05:45 +1000 Subject: [PATCH 1168/1342] drm/radeon/kms: implement bo busy check + current domain This implements the busy ioctl along with a current domain check. returns 0 or -EBUSY puts the current domain no matter what the answer. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon.h | 1 + drivers/gpu/drm/radeon/radeon_gem.c | 22 +++++++++++++++++++++- drivers/gpu/drm/radeon/radeon_object.c | 19 +++++++++++++++++++ include/drm/radeon_drm.h | 2 +- 4 files changed, 42 insertions(+), 2 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index 87170a56e37..79ad98264e3 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -242,6 +242,7 @@ int radeon_object_pin(struct radeon_object *robj, uint32_t domain, uint64_t *gpu_addr); void radeon_object_unpin(struct radeon_object *robj); int radeon_object_wait(struct radeon_object *robj); +int radeon_object_busy_domain(struct radeon_object *robj, uint32_t *cur_placement); int radeon_object_evict_vram(struct radeon_device *rdev); int radeon_object_mmap(struct radeon_object *robj, uint64_t *offset); void radeon_object_force_delete(struct radeon_device *rdev); diff --git a/drivers/gpu/drm/radeon/radeon_gem.c b/drivers/gpu/drm/radeon/radeon_gem.c index cded5180c75..d4ceff13bbb 100644 --- a/drivers/gpu/drm/radeon/radeon_gem.c +++ b/drivers/gpu/drm/radeon/radeon_gem.c @@ -262,7 +262,27 @@ int radeon_gem_mmap_ioctl(struct drm_device *dev, void *data, int radeon_gem_busy_ioctl(struct drm_device *dev, void *data, struct drm_file *filp) { - /* FIXME: implement */ + struct drm_radeon_gem_busy *args = data; + struct drm_gem_object *gobj; + struct radeon_object *robj; + int r; + uint32_t cur_placement; + + gobj = drm_gem_object_lookup(dev, filp, args->handle); + if (gobj == NULL) { + return -EINVAL; + } + robj = gobj->driver_private; + r = radeon_object_busy_domain(robj, &cur_placement); + if (cur_placement == TTM_PL_VRAM) + args->domain = RADEON_GEM_DOMAIN_VRAM; + if (cur_placement == TTM_PL_FLAG_TT) + args->domain = RADEON_GEM_DOMAIN_GTT; + if (cur_placement == TTM_PL_FLAG_SYSTEM) + args->domain = RADEON_GEM_DOMAIN_CPU; + mutex_lock(&dev->struct_mutex); + drm_gem_object_unreference(gobj); + mutex_unlock(&dev->struct_mutex); return 0; } diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c index e98cae3bf4a..b85fb83d7ae 100644 --- a/drivers/gpu/drm/radeon/radeon_object.c +++ b/drivers/gpu/drm/radeon/radeon_object.c @@ -316,6 +316,25 @@ int radeon_object_wait(struct radeon_object *robj) return r; } +int radeon_object_busy_domain(struct radeon_object *robj, uint32_t *cur_placement) +{ + int r = 0; + + r = radeon_object_reserve(robj, true); + if (unlikely(r != 0)) { + DRM_ERROR("radeon: failed to reserve object for waiting.\n"); + return r; + } + spin_lock(&robj->tobj.lock); + *cur_placement = robj->tobj.mem.mem_type; + if (robj->tobj.sync_obj) { + r = ttm_bo_wait(&robj->tobj, true, true, true); + } + spin_unlock(&robj->tobj.lock); + radeon_object_unreserve(robj); + return r; +} + int radeon_object_evict_vram(struct radeon_device *rdev) { if (rdev->flags & RADEON_IS_IGP) { diff --git a/include/drm/radeon_drm.h b/include/drm/radeon_drm.h index af4b4826997..f81c3232acc 100644 --- a/include/drm/radeon_drm.h +++ b/include/drm/radeon_drm.h @@ -838,7 +838,7 @@ struct drm_radeon_gem_wait_idle { struct drm_radeon_gem_busy { uint32_t handle; - uint32_t busy; + uint32_t domain; }; struct drm_radeon_gem_pread { -- GitLab From 9c0d90103c7e0eb6e638e5b649e9f6d8d9c1b4b3 Mon Sep 17 00:00:00 2001 From: Eric Paris Date: Fri, 31 Jul 2009 12:53:58 -0400 Subject: [PATCH 1169/1342] Capabilities: move cap_file_mmap to commoncap.c Currently we duplicate the mmap_min_addr test in cap_file_mmap and in security_file_mmap if !CONFIG_SECURITY. This patch moves cap_file_mmap into commoncap.c and then calls that function directly from security_file_mmap ifndef CONFIG_SECURITY like all of the other capability checks are done. Signed-off-by: Eric Paris Acked-by: Serge Hallyn Signed-off-by: James Morris --- include/linux/security.h | 7 ++++--- security/capability.c | 9 --------- security/commoncap.c | 30 ++++++++++++++++++++++++++++++ 3 files changed, 34 insertions(+), 12 deletions(-) diff --git a/include/linux/security.h b/include/linux/security.h index 5eff459b383..ac4bc3760b4 100644 --- a/include/linux/security.h +++ b/include/linux/security.h @@ -66,6 +66,9 @@ extern int cap_inode_setxattr(struct dentry *dentry, const char *name, extern int cap_inode_removexattr(struct dentry *dentry, const char *name); extern int cap_inode_need_killpriv(struct dentry *dentry); extern int cap_inode_killpriv(struct dentry *dentry); +extern int cap_file_mmap(struct file *file, unsigned long reqprot, + unsigned long prot, unsigned long flags, + unsigned long addr, unsigned long addr_only); extern int cap_task_fix_setuid(struct cred *new, const struct cred *old, int flags); extern int cap_task_prctl(int option, unsigned long arg2, unsigned long arg3, unsigned long arg4, unsigned long arg5); @@ -2197,9 +2200,7 @@ static inline int security_file_mmap(struct file *file, unsigned long reqprot, unsigned long addr, unsigned long addr_only) { - if ((addr < mmap_min_addr) && !capable(CAP_SYS_RAWIO)) - return -EACCES; - return 0; + return cap_file_mmap(file, reqprot, prot, flags, addr, addr_only); } static inline int security_file_mprotect(struct vm_area_struct *vma, diff --git a/security/capability.c b/security/capability.c index 21b6cead6a8..88f752e8152 100644 --- a/security/capability.c +++ b/security/capability.c @@ -330,15 +330,6 @@ static int cap_file_ioctl(struct file *file, unsigned int command, return 0; } -static int cap_file_mmap(struct file *file, unsigned long reqprot, - unsigned long prot, unsigned long flags, - unsigned long addr, unsigned long addr_only) -{ - if ((addr < mmap_min_addr) && !capable(CAP_SYS_RAWIO)) - return -EACCES; - return 0; -} - static int cap_file_mprotect(struct vm_area_struct *vma, unsigned long reqprot, unsigned long prot) { diff --git a/security/commoncap.c b/security/commoncap.c index 48b7e0228fa..6bcf6e81e54 100644 --- a/security/commoncap.c +++ b/security/commoncap.c @@ -984,3 +984,33 @@ int cap_vm_enough_memory(struct mm_struct *mm, long pages) cap_sys_admin = 1; return __vm_enough_memory(mm, pages, cap_sys_admin); } + +/* + * cap_file_mmap - check if able to map given addr + * @file: unused + * @reqprot: unused + * @prot: unused + * @flags: unused + * @addr: address attempting to be mapped + * @addr_only: unused + * + * If the process is attempting to map memory below mmap_min_addr they need + * CAP_SYS_RAWIO. The other parameters to this function are unused by the + * capability security module. Returns 0 if this mapping should be allowed + * -EPERM if not. + */ +int cap_file_mmap(struct file *file, unsigned long reqprot, + unsigned long prot, unsigned long flags, + unsigned long addr, unsigned long addr_only) +{ + int ret = 0; + + if (addr < mmap_min_addr) { + ret = cap_capable(current, current_cred(), CAP_SYS_RAWIO, + SECURITY_CAP_AUDIT); + /* set PF_SUPERPRIV if it turns out we allow the low mmap */ + if (ret == 0) + current->flags |= PF_SUPERPRIV; + } + return ret; +} -- GitLab From 8cf948e744e0218af604c32edecde10006dc8e9e Mon Sep 17 00:00:00 2001 From: Eric Paris Date: Fri, 31 Jul 2009 12:54:05 -0400 Subject: [PATCH 1170/1342] SELinux: call cap_file_mmap in selinux_file_mmap Currently SELinux does not check CAP_SYS_RAWIO in the file_mmap hook. This means there is no DAC check on the ability to mmap low addresses in the memory space. This function adds the DAC check for CAP_SYS_RAWIO while maintaining the selinux check on mmap_zero. This means that processes which need to mmap low memory will need CAP_SYS_RAWIO and mmap_zero but will NOT need the SELinux sys_rawio capability. Signed-off-by: Eric Paris Signed-off-by: James Morris --- security/selinux/hooks.c | 14 +++++++++++++- 1 file changed, 13 insertions(+), 1 deletion(-) diff --git a/security/selinux/hooks.c b/security/selinux/hooks.c index 1e8cfc4c2ed..e6d1432b080 100644 --- a/security/selinux/hooks.c +++ b/security/selinux/hooks.c @@ -3030,9 +3030,21 @@ static int selinux_file_mmap(struct file *file, unsigned long reqprot, int rc = 0; u32 sid = current_sid(); - if (addr < mmap_min_addr) + /* + * notice that we are intentionally putting the SELinux check before + * the secondary cap_file_mmap check. This is such a likely attempt + * at bad behaviour/exploit that we always want to get the AVC, even + * if DAC would have also denied the operation. + */ + if (addr < mmap_min_addr) { rc = avc_has_perm(sid, sid, SECCLASS_MEMPROTECT, MEMPROTECT__MMAP_ZERO, NULL); + if (rc) + return rc; + } + + /* do DAC check on address space usage */ + rc = cap_file_mmap(file, reqprot, prot, flags, addr, addr_only); if (rc || addr_only) return rc; -- GitLab From 788084aba2ab7348257597496befcbccabdc98a3 Mon Sep 17 00:00:00 2001 From: Eric Paris Date: Fri, 31 Jul 2009 12:54:11 -0400 Subject: [PATCH 1171/1342] Security/SELinux: seperate lsm specific mmap_min_addr Currently SELinux enforcement of controls on the ability to map low memory is determined by the mmap_min_addr tunable. This patch causes SELinux to ignore the tunable and instead use a seperate Kconfig option specific to how much space the LSM should protect. The tunable will now only control the need for CAP_SYS_RAWIO and SELinux permissions will always protect the amount of low memory designated by CONFIG_LSM_MMAP_MIN_ADDR. This allows users who need to disable the mmap_min_addr controls (usual reason being they run WINE as a non-root user) to do so and still have SELinux controls preventing confined domains (like a web server) from being able to map some area of low memory. Signed-off-by: Eric Paris Signed-off-by: James Morris --- include/linux/mm.h | 15 ------------ include/linux/security.h | 17 ++++++++++++++ kernel/sysctl.c | 7 +++--- mm/Kconfig | 6 ++--- mm/mmap.c | 3 --- mm/nommu.c | 3 --- security/Kconfig | 16 +++++++++++++ security/Makefile | 2 +- security/commoncap.c | 2 +- security/min_addr.c | 49 ++++++++++++++++++++++++++++++++++++++++ security/selinux/hooks.c | 2 +- 11 files changed, 92 insertions(+), 30 deletions(-) create mode 100644 security/min_addr.c diff --git a/include/linux/mm.h b/include/linux/mm.h index ba3a7cb1eaa..9a72cc78e6b 100644 --- a/include/linux/mm.h +++ b/include/linux/mm.h @@ -34,8 +34,6 @@ extern int sysctl_legacy_va_layout; #define sysctl_legacy_va_layout 0 #endif -extern unsigned long mmap_min_addr; - #include #include #include @@ -574,19 +572,6 @@ static inline void set_page_links(struct page *page, enum zone_type zone, set_page_section(page, pfn_to_section_nr(pfn)); } -/* - * If a hint addr is less than mmap_min_addr change hint to be as - * low as possible but still greater than mmap_min_addr - */ -static inline unsigned long round_hint_to_min(unsigned long hint) -{ - hint &= PAGE_MASK; - if (((void *)hint != NULL) && - (hint < mmap_min_addr)) - return PAGE_ALIGN(mmap_min_addr); - return hint; -} - /* * Some inline functions in vmstat.h depend on page_zone() */ diff --git a/include/linux/security.h b/include/linux/security.h index ac4bc3760b4..dc3472c1f78 100644 --- a/include/linux/security.h +++ b/include/linux/security.h @@ -28,6 +28,7 @@ #include #include #include +#include /* PAGE_ALIGN */ #include #include #include @@ -95,6 +96,7 @@ extern int cap_netlink_send(struct sock *sk, struct sk_buff *skb); extern int cap_netlink_recv(struct sk_buff *skb, int cap); extern unsigned long mmap_min_addr; +extern unsigned long dac_mmap_min_addr; /* * Values used in the task_security_ops calls */ @@ -147,6 +149,21 @@ static inline void security_free_mnt_opts(struct security_mnt_opts *opts) opts->num_mnt_opts = 0; } +/* + * If a hint addr is less than mmap_min_addr change hint to be as + * low as possible but still greater than mmap_min_addr + */ +static inline unsigned long round_hint_to_min(unsigned long hint) +{ + hint &= PAGE_MASK; + if (((void *)hint != NULL) && + (hint < mmap_min_addr)) + return PAGE_ALIGN(mmap_min_addr); + return hint; +} + +extern int mmap_min_addr_handler(struct ctl_table *table, int write, struct file *filp, + void __user *buffer, size_t *lenp, loff_t *ppos); /** * struct security_operations - main security structure * diff --git a/kernel/sysctl.c b/kernel/sysctl.c index 98e02328c67..58be76017fd 100644 --- a/kernel/sysctl.c +++ b/kernel/sysctl.c @@ -49,6 +49,7 @@ #include #include #include +#include #include #include @@ -1306,10 +1307,10 @@ static struct ctl_table vm_table[] = { { .ctl_name = CTL_UNNUMBERED, .procname = "mmap_min_addr", - .data = &mmap_min_addr, - .maxlen = sizeof(unsigned long), + .data = &dac_mmap_min_addr, + .maxlen = sizeof(unsigned long), .mode = 0644, - .proc_handler = &proc_doulongvec_minmax, + .proc_handler = &mmap_min_addr_handler, }, #ifdef CONFIG_NUMA { diff --git a/mm/Kconfig b/mm/Kconfig index c948d4ca8bd..fe5f674d7a7 100644 --- a/mm/Kconfig +++ b/mm/Kconfig @@ -225,9 +225,9 @@ config DEFAULT_MMAP_MIN_ADDR For most ia64, ppc64 and x86 users with lots of address space a value of 65536 is reasonable and should cause no problems. On arm and other archs it should not be higher than 32768. - Programs which use vm86 functionality would either need additional - permissions from either the LSM or the capabilities module or have - this protection disabled. + Programs which use vm86 functionality or have some need to map + this low address space will need CAP_SYS_RAWIO or disable this + protection by setting the value to 0. This value can be changed after boot using the /proc/sys/vm/mmap_min_addr tunable. diff --git a/mm/mmap.c b/mm/mmap.c index 34579b23ebd..8101de490c7 100644 --- a/mm/mmap.c +++ b/mm/mmap.c @@ -88,9 +88,6 @@ int sysctl_overcommit_ratio = 50; /* default is 50% */ int sysctl_max_map_count __read_mostly = DEFAULT_MAX_MAP_COUNT; struct percpu_counter vm_committed_as; -/* amount of vm to protect from userspace access */ -unsigned long mmap_min_addr = CONFIG_DEFAULT_MMAP_MIN_ADDR; - /* * Check that a process has enough memory to allocate a new virtual * mapping. 0 means there is enough memory for the allocation to diff --git a/mm/nommu.c b/mm/nommu.c index 53cab10fece..28754c40be9 100644 --- a/mm/nommu.c +++ b/mm/nommu.c @@ -69,9 +69,6 @@ int sysctl_max_map_count = DEFAULT_MAX_MAP_COUNT; int sysctl_nr_trim_pages = CONFIG_NOMMU_INITIAL_TRIM_EXCESS; int heap_stack_gap = 0; -/* amount of vm to protect from userspace access */ -unsigned long mmap_min_addr = CONFIG_DEFAULT_MMAP_MIN_ADDR; - atomic_long_t mmap_pages_allocated; EXPORT_SYMBOL(mem_map); diff --git a/security/Kconfig b/security/Kconfig index d23c839038f..9c60c346a91 100644 --- a/security/Kconfig +++ b/security/Kconfig @@ -113,6 +113,22 @@ config SECURITY_ROOTPLUG If you are unsure how to answer this question, answer N. +config LSM_MMAP_MIN_ADDR + int "Low address space for LSM to from user allocation" + depends on SECURITY && SECURITY_SELINUX + default 65535 + help + This is the portion of low virtual memory which should be protected + from userspace allocation. Keeping a user from writing to low pages + can help reduce the impact of kernel NULL pointer bugs. + + For most ia64, ppc64 and x86 users with lots of address space + a value of 65536 is reasonable and should cause no problems. + On arm and other archs it should not be higher than 32768. + Programs which use vm86 functionality or have some need to map + this low address space will need the permission specific to the + systems running LSM. + source security/selinux/Kconfig source security/smack/Kconfig source security/tomoyo/Kconfig diff --git a/security/Makefile b/security/Makefile index c67557cdaa8..b56e7f9ecbc 100644 --- a/security/Makefile +++ b/security/Makefile @@ -8,7 +8,7 @@ subdir-$(CONFIG_SECURITY_SMACK) += smack subdir-$(CONFIG_SECURITY_TOMOYO) += tomoyo # always enable default capabilities -obj-y += commoncap.o +obj-y += commoncap.o min_addr.o # Object file lists obj-$(CONFIG_SECURITY) += security.o capability.o diff --git a/security/commoncap.c b/security/commoncap.c index 6bcf6e81e54..e3097c0a131 100644 --- a/security/commoncap.c +++ b/security/commoncap.c @@ -1005,7 +1005,7 @@ int cap_file_mmap(struct file *file, unsigned long reqprot, { int ret = 0; - if (addr < mmap_min_addr) { + if (addr < dac_mmap_min_addr) { ret = cap_capable(current, current_cred(), CAP_SYS_RAWIO, SECURITY_CAP_AUDIT); /* set PF_SUPERPRIV if it turns out we allow the low mmap */ diff --git a/security/min_addr.c b/security/min_addr.c new file mode 100644 index 00000000000..14cc7b3b8d0 --- /dev/null +++ b/security/min_addr.c @@ -0,0 +1,49 @@ +#include +#include +#include +#include + +/* amount of vm to protect from userspace access by both DAC and the LSM*/ +unsigned long mmap_min_addr; +/* amount of vm to protect from userspace using CAP_SYS_RAWIO (DAC) */ +unsigned long dac_mmap_min_addr = CONFIG_DEFAULT_MMAP_MIN_ADDR; +/* amount of vm to protect from userspace using the LSM = CONFIG_LSM_MMAP_MIN_ADDR */ + +/* + * Update mmap_min_addr = max(dac_mmap_min_addr, CONFIG_LSM_MMAP_MIN_ADDR) + */ +static void update_mmap_min_addr(void) +{ +#ifdef CONFIG_LSM_MMAP_MIN_ADDR + if (dac_mmap_min_addr > CONFIG_LSM_MMAP_MIN_ADDR) + mmap_min_addr = dac_mmap_min_addr; + else + mmap_min_addr = CONFIG_LSM_MMAP_MIN_ADDR; +#else + mmap_min_addr = dac_mmap_min_addr; +#endif +} + +/* + * sysctl handler which just sets dac_mmap_min_addr = the new value and then + * calls update_mmap_min_addr() so non MAP_FIXED hints get rounded properly + */ +int mmap_min_addr_handler(struct ctl_table *table, int write, struct file *filp, + void __user *buffer, size_t *lenp, loff_t *ppos) +{ + int ret; + + ret = proc_doulongvec_minmax(table, write, filp, buffer, lenp, ppos); + + update_mmap_min_addr(); + + return ret; +} + +int __init init_mmap_min_addr(void) +{ + update_mmap_min_addr(); + + return 0; +} +pure_initcall(init_mmap_min_addr); diff --git a/security/selinux/hooks.c b/security/selinux/hooks.c index e6d1432b080..8d8b69c5664 100644 --- a/security/selinux/hooks.c +++ b/security/selinux/hooks.c @@ -3036,7 +3036,7 @@ static int selinux_file_mmap(struct file *file, unsigned long reqprot, * at bad behaviour/exploit that we always want to get the AVC, even * if DAC would have also denied the operation. */ - if (addr < mmap_min_addr) { + if (addr < CONFIG_LSM_MMAP_MIN_ADDR) { rc = avc_has_perm(sid, sid, SECCLASS_MEMPROTECT, MEMPROTECT__MMAP_ZERO, NULL); if (rc) -- GitLab From 1d9959734a1949ea4f2427bd2d8b21ede6b2441c Mon Sep 17 00:00:00 2001 From: Eric Paris Date: Fri, 7 Aug 2009 14:53:57 -0400 Subject: [PATCH 1172/1342] security: define round_hint_to_min in !CONFIG_SECURITY Fix the header files to define round_hint_to_min() and to define mmap_min_addr_handler() in the !CONFIG_SECURITY case. Built and tested with !CONFIG_SECURITY Signed-off-by: Eric Paris Signed-off-by: James Morris --- include/linux/security.h | 30 +++++++++++++++--------------- 1 file changed, 15 insertions(+), 15 deletions(-) diff --git a/include/linux/security.h b/include/linux/security.h index dc3472c1f78..1f16eea2017 100644 --- a/include/linux/security.h +++ b/include/linux/security.h @@ -121,6 +121,21 @@ struct request_sock; #define LSM_UNSAFE_PTRACE 2 #define LSM_UNSAFE_PTRACE_CAP 4 +/* + * If a hint addr is less than mmap_min_addr change hint to be as + * low as possible but still greater than mmap_min_addr + */ +static inline unsigned long round_hint_to_min(unsigned long hint) +{ + hint &= PAGE_MASK; + if (((void *)hint != NULL) && + (hint < mmap_min_addr)) + return PAGE_ALIGN(mmap_min_addr); + return hint; +} +extern int mmap_min_addr_handler(struct ctl_table *table, int write, struct file *filp, + void __user *buffer, size_t *lenp, loff_t *ppos); + #ifdef CONFIG_SECURITY struct security_mnt_opts { @@ -149,21 +164,6 @@ static inline void security_free_mnt_opts(struct security_mnt_opts *opts) opts->num_mnt_opts = 0; } -/* - * If a hint addr is less than mmap_min_addr change hint to be as - * low as possible but still greater than mmap_min_addr - */ -static inline unsigned long round_hint_to_min(unsigned long hint) -{ - hint &= PAGE_MASK; - if (((void *)hint != NULL) && - (hint < mmap_min_addr)) - return PAGE_ALIGN(mmap_min_addr); - return hint; -} - -extern int mmap_min_addr_handler(struct ctl_table *table, int write, struct file *filp, - void __user *buffer, size_t *lenp, loff_t *ppos); /** * struct security_operations - main security structure * -- GitLab From bc990f5cb424cdca9dda866785d088e2c2110ecc Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Sun, 16 Aug 2009 20:36:34 -0400 Subject: [PATCH 1173/1342] xfs: fix locking in xfs_iget_cache_hit The locking in xfs_iget_cache_hit currently has numerous problems: - we clear the reclaim tag without i_flags_lock which protects modifications to it - we call inode_init_always which can sleep with pag_ici_lock held (this is oss.sgi.com BZ #819) - we acquire and drop i_flags_lock a lot and thus provide no consistency between the various flags we set/clear under it This patch fixes all that with a major revamp of the locking in the function. The new version acquires i_flags_lock early and only drops it once we need to call into inode_init_always or before calling xfs_ilock. This patch fixes a bug seen in the wild where we race modifying the reclaim tag. Signed-off-by: Christoph Hellwig Reviewed-by: Felix Blyakher Reviewed-by: Eric Sandeen Signed-off-by: Felix Blyakher --- fs/xfs/linux-2.6/xfs_sync.c | 13 ++++- fs/xfs/linux-2.6/xfs_sync.h | 1 + fs/xfs/xfs_iget.c | 113 ++++++++++++++++++------------------ 3 files changed, 70 insertions(+), 57 deletions(-) diff --git a/fs/xfs/linux-2.6/xfs_sync.c b/fs/xfs/linux-2.6/xfs_sync.c index b619d6b8ca4..98ef624d9ba 100644 --- a/fs/xfs/linux-2.6/xfs_sync.c +++ b/fs/xfs/linux-2.6/xfs_sync.c @@ -708,6 +708,16 @@ xfs_reclaim_inode( return 0; } +void +__xfs_inode_set_reclaim_tag( + struct xfs_perag *pag, + struct xfs_inode *ip) +{ + radix_tree_tag_set(&pag->pag_ici_root, + XFS_INO_TO_AGINO(ip->i_mount, ip->i_ino), + XFS_ICI_RECLAIM_TAG); +} + /* * We set the inode flag atomically with the radix tree tag. * Once we get tag lookups on the radix tree, this inode flag @@ -722,8 +732,7 @@ xfs_inode_set_reclaim_tag( read_lock(&pag->pag_ici_lock); spin_lock(&ip->i_flags_lock); - radix_tree_tag_set(&pag->pag_ici_root, - XFS_INO_TO_AGINO(mp, ip->i_ino), XFS_ICI_RECLAIM_TAG); + __xfs_inode_set_reclaim_tag(pag, ip); __xfs_iflags_set(ip, XFS_IRECLAIMABLE); spin_unlock(&ip->i_flags_lock); read_unlock(&pag->pag_ici_lock); diff --git a/fs/xfs/linux-2.6/xfs_sync.h b/fs/xfs/linux-2.6/xfs_sync.h index 2a10301c99c..59120602588 100644 --- a/fs/xfs/linux-2.6/xfs_sync.h +++ b/fs/xfs/linux-2.6/xfs_sync.h @@ -48,6 +48,7 @@ int xfs_reclaim_inode(struct xfs_inode *ip, int locked, int sync_mode); int xfs_reclaim_inodes(struct xfs_mount *mp, int mode); void xfs_inode_set_reclaim_tag(struct xfs_inode *ip); +void __xfs_inode_set_reclaim_tag(struct xfs_perag *pag, struct xfs_inode *ip); void xfs_inode_clear_reclaim_tag(struct xfs_inode *ip); void __xfs_inode_clear_reclaim_tag(struct xfs_mount *mp, struct xfs_perag *pag, struct xfs_inode *ip); diff --git a/fs/xfs/xfs_iget.c b/fs/xfs/xfs_iget.c index 34ec86923f7..ecbf8b4d2e2 100644 --- a/fs/xfs/xfs_iget.c +++ b/fs/xfs/xfs_iget.c @@ -191,80 +191,82 @@ xfs_iget_cache_hit( int flags, int lock_flags) __releases(pag->pag_ici_lock) { + struct inode *inode = VFS_I(ip); struct xfs_mount *mp = ip->i_mount; - int error = EAGAIN; + int error; + + spin_lock(&ip->i_flags_lock); /* - * If INEW is set this inode is being set up - * If IRECLAIM is set this inode is being torn down - * Pause and try again. + * If we are racing with another cache hit that is currently + * instantiating this inode or currently recycling it out of + * reclaimabe state, wait for the initialisation to complete + * before continuing. + * + * XXX(hch): eventually we should do something equivalent to + * wait_on_inode to wait for these flags to be cleared + * instead of polling for it. */ - if (xfs_iflags_test(ip, (XFS_INEW|XFS_IRECLAIM))) { + if (ip->i_flags & (XFS_INEW|XFS_IRECLAIM)) { XFS_STATS_INC(xs_ig_frecycle); + error = EAGAIN; goto out_error; } - /* If IRECLAIMABLE is set, we've torn down the vfs inode part */ - if (xfs_iflags_test(ip, XFS_IRECLAIMABLE)) { - - /* - * If lookup is racing with unlink, then we should return an - * error immediately so we don't remove it from the reclaim - * list and potentially leak the inode. - */ - if ((ip->i_d.di_mode == 0) && !(flags & XFS_IGET_CREATE)) { - error = ENOENT; - goto out_error; - } + /* + * If lookup is racing with unlink return an error immediately. + */ + if (ip->i_d.di_mode == 0 && !(flags & XFS_IGET_CREATE)) { + error = ENOENT; + goto out_error; + } + /* + * If IRECLAIMABLE is set, we've torn down the VFS inode already. + * Need to carefully get it back into useable state. + */ + if (ip->i_flags & XFS_IRECLAIMABLE) { xfs_itrace_exit_tag(ip, "xfs_iget.alloc"); /* - * We need to re-initialise the VFS inode as it has been - * 'freed' by the VFS. Do this here so we can deal with - * errors cleanly, then tag it so it can be set up correctly - * later. + * We need to set XFS_INEW atomically with clearing the + * reclaimable tag so that we do have an indicator of the + * inode still being initialized. */ - if (inode_init_always(mp->m_super, VFS_I(ip))) { - error = ENOMEM; - goto out_error; - } + ip->i_flags |= XFS_INEW; + ip->i_flags &= ~XFS_IRECLAIMABLE; + __xfs_inode_clear_reclaim_tag(mp, pag, ip); - /* - * We must set the XFS_INEW flag before clearing the - * XFS_IRECLAIMABLE flag so that if a racing lookup does - * not find the XFS_IRECLAIMABLE above but has the igrab() - * below succeed we can safely check XFS_INEW to detect - * that this inode is still being initialised. - */ - xfs_iflags_set(ip, XFS_INEW); - xfs_iflags_clear(ip, XFS_IRECLAIMABLE); + spin_unlock(&ip->i_flags_lock); + read_unlock(&pag->pag_ici_lock); - /* clear the radix tree reclaim flag as well. */ - __xfs_inode_clear_reclaim_tag(mp, pag, ip); - } else if (!igrab(VFS_I(ip))) { + error = -inode_init_always(mp->m_super, inode); + if (error) { + /* + * Re-initializing the inode failed, and we are in deep + * trouble. Try to re-add it to the reclaim list. + */ + read_lock(&pag->pag_ici_lock); + spin_lock(&ip->i_flags_lock); + + ip->i_flags &= ~XFS_INEW; + ip->i_flags |= XFS_IRECLAIMABLE; + __xfs_inode_set_reclaim_tag(pag, ip); + goto out_error; + } + inode->i_state = I_LOCK|I_NEW; + } else { /* If the VFS inode is being torn down, pause and try again. */ - XFS_STATS_INC(xs_ig_frecycle); - goto out_error; - } else if (xfs_iflags_test(ip, XFS_INEW)) { - /* - * We are racing with another cache hit that is - * currently recycling this inode out of the XFS_IRECLAIMABLE - * state. Wait for the initialisation to complete before - * continuing. - */ - wait_on_inode(VFS_I(ip)); - } + if (!igrab(inode)) { + error = EAGAIN; + goto out_error; + } - if (ip->i_d.di_mode == 0 && !(flags & XFS_IGET_CREATE)) { - error = ENOENT; - iput(VFS_I(ip)); - goto out_error; + /* We've got a live one. */ + spin_unlock(&ip->i_flags_lock); + read_unlock(&pag->pag_ici_lock); } - /* We've got a live one. */ - read_unlock(&pag->pag_ici_lock); - if (lock_flags != 0) xfs_ilock(ip, lock_flags); @@ -274,6 +276,7 @@ xfs_iget_cache_hit( return 0; out_error: + spin_unlock(&ip->i_flags_lock); read_unlock(&pag->pag_ici_lock); return error; } -- GitLab From c7f6fa44115d401e89db730f357629d39f8e4ba6 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Tue, 28 Jul 2009 23:52:54 +0200 Subject: [PATCH 1174/1342] x86, mce: don't log boot MCEs on Pentium M (model == 13) CPUs On my legacy Pentium M laptop (Acer Extensa 2900) I get bogus MCE on a cold boot with CONFIG_X86_NEW_MCE enabled, i.e. (after decoding it with mcelog): MCE 0 HARDWARE ERROR. This is *NOT* a software problem! Please contact your hardware vendor CPU 0 BANK 1 MCG status: MCi status: Error overflow Uncorrected error Error enabled Processor context corrupt MCA: Data CACHE Level-1 UNKNOWN Error STATUS f200000000000195 MCGSTATUS 0 [ The other STATUS values observed: f2000000000001b5 (... UNKNOWN error) and f200000000000115 (... READ Error). To verify that this is not a CONFIG_X86_NEW_MCE bug I also modified the CONFIG_X86_OLD_MCE code (which doesn't log any MCEs) to dump content of STATUS MSR before it is cleared during initialization. ] Since the bogus MCE results in a kernel taint (which in turn disables lockdep support) don't log boot MCEs on Pentium M (model == 13) CPUs by default ("mce=bootlog" boot parameter can be be used to get the old behavior). Signed-off-by: Bartlomiej Zolnierkiewicz Reviewed-by: Andi Kleen Signed-off-by: H. Peter Anvin Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/mcheck/mce.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/x86/kernel/cpu/mcheck/mce.c b/arch/x86/kernel/cpu/mcheck/mce.c index 1cfb623ce11..a0c2910d96a 100644 --- a/arch/x86/kernel/cpu/mcheck/mce.c +++ b/arch/x86/kernel/cpu/mcheck/mce.c @@ -1273,6 +1273,10 @@ static void mce_cpu_quirks(struct cpuinfo_x86 *c) if ((c->x86 > 6 || (c->x86 == 6 && c->x86_model >= 0xe)) && monarch_timeout < 0) monarch_timeout = USEC_PER_SEC; + + /* There are also broken BIOSes on some Pentium M systems. */ + if (c->x86 == 6 && c->x86_model == 13 && mce_bootlog < 0) + mce_bootlog = 0; } if (monarch_timeout < 0) monarch_timeout = 0; -- GitLab From 2932cffc89e9a1476b28a59896fa4f81e0d4f131 Mon Sep 17 00:00:00 2001 From: "Carlos R. Mafra" Date: Mon, 17 Aug 2009 00:36:21 +0200 Subject: [PATCH 1175/1342] perf: Rename perf-examples.txt to examples.txt Rename it to examples.txt to avoid the perf-*.txt pattern in the Makefile, otherwise 'make doc' fails because perf-examples.txt is not formatted to be a man page: ERROR: perf-examples.txt: line 1: manpage document title is mandatory Signed-off-by: Carlos R. Mafra Cc: Peter Zijlstra Cc: Paul Mackerras LKML-Reference: Signed-off-by: Ingo Molnar --- tools/perf/Documentation/{perf-examples.txt => examples.txt} | 0 1 file changed, 0 insertions(+), 0 deletions(-) rename tools/perf/Documentation/{perf-examples.txt => examples.txt} (100%) diff --git a/tools/perf/Documentation/perf-examples.txt b/tools/perf/Documentation/examples.txt similarity index 100% rename from tools/perf/Documentation/perf-examples.txt rename to tools/perf/Documentation/examples.txt -- GitLab From e1ac3614ff606ae03677f47459113f98a19af63c Mon Sep 17 00:00:00 2001 From: Paul Mackerras Date: Fri, 14 Aug 2009 15:39:10 +1000 Subject: [PATCH 1176/1342] perf_counter: Check task on counter read IPI In general, code in perf_counter.c that is called through an IPI checks, for per-task counters, that the counter's task is still the current task. This is to handle the race condition where the cpu switches from the task we want to another task in the interval between sending the IPI and the IPI arriving and being handled on the target CPU. For some reason, __perf_counter_read is missing this check, yet there is no reason why the race condition can't occur. This adds a check that the current task is the one we want. If it isn't, we just return. In that case the counter->count value should be up to date, since it will have been updated when the counter was scheduled out, which must have happened since the IPI was sent. I don't have an example of an actual failure due to this race, but it seems obvious that it could occur and we need to guard against it. Signed-off-by: Paul Mackerras Acked-by: Peter Zijlstra LKML-Reference: <19076.63614.277861.368125@drongo.ozlabs.ibm.com> Signed-off-by: Ingo Molnar --- kernel/perf_counter.c | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index 534e20d14d6..b8fe7397b90 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -1503,10 +1503,21 @@ static void perf_counter_enable_on_exec(struct task_struct *task) */ static void __perf_counter_read(void *info) { + struct perf_cpu_context *cpuctx = &__get_cpu_var(perf_cpu_context); struct perf_counter *counter = info; struct perf_counter_context *ctx = counter->ctx; unsigned long flags; + /* + * If this is a task context, we need to check whether it is + * the current task context of this cpu. If not it has been + * scheduled out before the smp call arrived. In that case + * counter->count would have been updated to a recent sample + * when the counter was scheduled out. + */ + if (ctx->task && cpuctx->task_ctx != ctx) + return; + local_irq_save(flags); if (ctx->is_active) update_context_time(ctx); -- GitLab From de809347aeef0a68c04576c464414d0e4dce59fc Mon Sep 17 00:00:00 2001 From: Amerigo Wang Date: Mon, 17 Aug 2009 05:43:01 -0400 Subject: [PATCH 1177/1342] timers: Drop write permission on /proc/timer_list /proc/timer_list and /proc/slabinfo are not supposed to be written, so there should be no write permissions on it. Signed-off-by: WANG Cong Cc: Pekka Enberg Cc: Vegard Nossum Cc: Eduard - Gabriel Munteanu Cc: linux-mm@kvack.org Cc: Christoph Lameter Cc: David Rientjes Cc: Amerigo Wang Cc: Matt Mackall Cc: Arjan van de Ven LKML-Reference: <20090817094525.6355.88682.sendpatchset@localhost.localdomain> Signed-off-by: Ingo Molnar --- kernel/time/timer_list.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/time/timer_list.c b/kernel/time/timer_list.c index a999b92a127..fddd69d16e0 100644 --- a/kernel/time/timer_list.c +++ b/kernel/time/timer_list.c @@ -286,7 +286,7 @@ static int __init init_timer_list_procfs(void) { struct proc_dir_entry *pe; - pe = proc_create("timer_list", 0644, NULL, &timer_list_fops); + pe = proc_create("timer_list", 0444, NULL, &timer_list_fops); if (!pe) return -ENOMEM; return 0; -- GitLab From e412cd257e0d51e0ecbb89f50953835b5a0681b2 Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Mon, 17 Aug 2009 10:19:00 +0200 Subject: [PATCH 1178/1342] x86, mce: Don't initialize MCEs on unknown CPUs An older test-box started hanging at the following point during bootup: [ 0.022996] Mount-cache hash table entries: 512 [ 0.024996] Initializing cgroup subsys debug [ 0.025996] Initializing cgroup subsys cpuacct [ 0.026995] Initializing cgroup subsys devices [ 0.027995] Initializing cgroup subsys freezer [ 0.028995] mce: CPU supports 5 MCE banks I've bisected it down to commit 4efc0670 ("x86, mce: use 64bit machine check code on 32bit"), which utilizes the MCE code on 32-bit systems too. The problem is caused by this detail in my config: # CONFIG_CPU_SUP_INTEL is not set This disables the quirks in mce_cpu_quirks() but still enables MCE support - which then hangs due to the missing quirk workaround needed on this CPU: if (c->x86 == 6 && c->x86_model < 0x1A && banks > 0) mce_banks[0].init = 0; The safe solution is to not initialize MCEs if we dont know on what CPU we are running (or if that CPU's support code got disabled in the config). Also be a bit more defensive on 32-bit systems: dont do a boot-time dump of pending MCEs not just on the specific system that we found a problem with (Pentium-M), but earlier ones as well. Now this problem is probably not common and disabling CPU support is rare - but still being more defensive in something we turned on for a wide range of CPUs is prudent. Cc: Hidetoshi Seto LKML-Reference: Message-ID: <4A88E3E4.40506@jp.fujitsu.com> Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/mcheck/mce.c | 19 ++++++++++++++----- 1 file changed, 14 insertions(+), 5 deletions(-) diff --git a/arch/x86/kernel/cpu/mcheck/mce.c b/arch/x86/kernel/cpu/mcheck/mce.c index a0c2910d96a..01213048f62 100644 --- a/arch/x86/kernel/cpu/mcheck/mce.c +++ b/arch/x86/kernel/cpu/mcheck/mce.c @@ -1226,8 +1226,13 @@ static void mce_init(void) } /* Add per CPU specific workarounds here */ -static void mce_cpu_quirks(struct cpuinfo_x86 *c) +static int mce_cpu_quirks(struct cpuinfo_x86 *c) { + if (c->x86_vendor == X86_VENDOR_UNKNOWN) { + pr_info("MCE: unknown CPU type - not enabling MCE support.\n"); + return -EOPNOTSUPP; + } + /* This should be disabled by the BIOS, but isn't always */ if (c->x86_vendor == X86_VENDOR_AMD) { if (c->x86 == 15 && banks > 4) { @@ -1274,14 +1279,19 @@ static void mce_cpu_quirks(struct cpuinfo_x86 *c) monarch_timeout < 0) monarch_timeout = USEC_PER_SEC; - /* There are also broken BIOSes on some Pentium M systems. */ - if (c->x86 == 6 && c->x86_model == 13 && mce_bootlog < 0) + /* + * There are also broken BIOSes on some Pentium M and + * earlier systems: + */ + if (c->x86 == 6 && c->x86_model <= 13 && mce_bootlog < 0) mce_bootlog = 0; } if (monarch_timeout < 0) monarch_timeout = 0; if (mce_bootlog != 0) mce_panic_timeout = 30; + + return 0; } static void __cpuinit mce_ancient_init(struct cpuinfo_x86 *c) @@ -1342,11 +1352,10 @@ void __cpuinit mcheck_init(struct cpuinfo_x86 *c) if (!mce_available(c)) return; - if (mce_cap_init() < 0) { + if (mce_cap_init() < 0 || mce_cpu_quirks(c) < 0) { mce_disabled = 1; return; } - mce_cpu_quirks(c); machine_check_vector = do_machine_check; -- GitLab From 87c62a66edd645a9b1ff1f9b00ab20c5a93d8845 Mon Sep 17 00:00:00 2001 From: Atsushi Nemoto Date: Tue, 14 Jul 2009 22:37:09 +0900 Subject: [PATCH 1179/1342] MIPS: Fix HPAGE_SIZE redefinition This patch fixes warnings like this: CC fs/proc/meminfo.o In file included from /work/linux/include/linux/mmzone.h:20, from /work/linux/include/linux/gfp.h:4, from /work/linux/include/linux/mm.h:8, from /work/linux/fs/proc/meminfo.c:5: /work/linux/arch/mips/include/asm/page.h:36:1: warning: "HPAGE_SIZE" redefined In file included from /work/linux/fs/proc/meminfo.c:2: /work/linux/include/linux/hugetlb.h:107:1: warning: this is the location of the previous definition Signed-off-by: Atsushi Nemoto Acked-by: David Daney Signed-off-by: Ralf Baechle --- arch/mips/include/asm/page.h | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/mips/include/asm/page.h b/arch/mips/include/asm/page.h index 96a14a426a7..4320239cf4e 100644 --- a/arch/mips/include/asm/page.h +++ b/arch/mips/include/asm/page.h @@ -32,10 +32,12 @@ #define PAGE_SIZE (1UL << PAGE_SHIFT) #define PAGE_MASK (~((1 << PAGE_SHIFT) - 1)) +#ifdef CONFIG_HUGETLB_PAGE #define HPAGE_SHIFT (PAGE_SHIFT + PAGE_SHIFT - 3) #define HPAGE_SIZE ((1UL) << HPAGE_SHIFT) #define HPAGE_MASK (~(HPAGE_SIZE - 1)) #define HUGETLB_PAGE_ORDER (HPAGE_SHIFT - PAGE_SHIFT) +#endif /* CONFIG_HUGETLB_PAGE */ #ifndef __ASSEMBLY__ -- GitLab From 523d2f6982136d332c9b7dd00e9e16da1091f060 Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Wed, 1 Jul 2009 21:26:43 +0200 Subject: [PATCH 1180/1342] mac80211: fix todo lock The key todo lock can be taken from different locks that require it to be _bh to avoid lock inversion due to (soft)irqs. This should fix the two problems reported by Bob and Gabor: http://mid.gmane.org/20090619113049.GB18956@hash.localnet http://mid.gmane.org/4A3FA376.8020307@openwrt.org Signed-off-by: Johannes Berg Cc: Bob Copeland Cc: Gabor Juhos Signed-off-by: John W. Linville --- net/mac80211/key.c | 28 +++++++++++++++------------- 1 file changed, 15 insertions(+), 13 deletions(-) diff --git a/net/mac80211/key.c b/net/mac80211/key.c index ce267565e18..659a42d529e 100644 --- a/net/mac80211/key.c +++ b/net/mac80211/key.c @@ -67,6 +67,8 @@ static DECLARE_WORK(todo_work, key_todo); * * @key: key to add to do item for * @flag: todo flag(s) + * + * Must be called with IRQs or softirqs disabled. */ static void add_todo(struct ieee80211_key *key, u32 flag) { @@ -140,9 +142,9 @@ static void ieee80211_key_enable_hw_accel(struct ieee80211_key *key) ret = drv_set_key(key->local, SET_KEY, &sdata->vif, sta, &key->conf); if (!ret) { - spin_lock(&todo_lock); + spin_lock_bh(&todo_lock); key->flags |= KEY_FLAG_UPLOADED_TO_HARDWARE; - spin_unlock(&todo_lock); + spin_unlock_bh(&todo_lock); } if (ret && ret != -ENOSPC && ret != -EOPNOTSUPP) @@ -164,12 +166,12 @@ static void ieee80211_key_disable_hw_accel(struct ieee80211_key *key) if (!key || !key->local->ops->set_key) return; - spin_lock(&todo_lock); + spin_lock_bh(&todo_lock); if (!(key->flags & KEY_FLAG_UPLOADED_TO_HARDWARE)) { - spin_unlock(&todo_lock); + spin_unlock_bh(&todo_lock); return; } - spin_unlock(&todo_lock); + spin_unlock_bh(&todo_lock); sta = get_sta_for_key(key); sdata = key->sdata; @@ -188,9 +190,9 @@ static void ieee80211_key_disable_hw_accel(struct ieee80211_key *key) wiphy_name(key->local->hw.wiphy), key->conf.keyidx, sta ? sta->addr : bcast_addr, ret); - spin_lock(&todo_lock); + spin_lock_bh(&todo_lock); key->flags &= ~KEY_FLAG_UPLOADED_TO_HARDWARE; - spin_unlock(&todo_lock); + spin_unlock_bh(&todo_lock); } static void __ieee80211_set_default_key(struct ieee80211_sub_if_data *sdata, @@ -437,14 +439,14 @@ void ieee80211_key_link(struct ieee80211_key *key, __ieee80211_key_replace(sdata, sta, old_key, key); - spin_unlock_irqrestore(&sdata->local->key_lock, flags); - /* free old key later */ add_todo(old_key, KEY_FLAG_TODO_DELETE); add_todo(key, KEY_FLAG_TODO_ADD_DEBUGFS); if (netif_running(sdata->dev)) add_todo(key, KEY_FLAG_TODO_HWACCEL_ADD); + + spin_unlock_irqrestore(&sdata->local->key_lock, flags); } static void __ieee80211_key_free(struct ieee80211_key *key) @@ -547,7 +549,7 @@ static void __ieee80211_key_todo(void) */ synchronize_rcu(); - spin_lock(&todo_lock); + spin_lock_bh(&todo_lock); while (!list_empty(&todo_list)) { key = list_first_entry(&todo_list, struct ieee80211_key, todo); list_del_init(&key->todo); @@ -558,7 +560,7 @@ static void __ieee80211_key_todo(void) KEY_FLAG_TODO_HWACCEL_REMOVE | KEY_FLAG_TODO_DELETE); key->flags &= ~todoflags; - spin_unlock(&todo_lock); + spin_unlock_bh(&todo_lock); work_done = false; @@ -591,9 +593,9 @@ static void __ieee80211_key_todo(void) WARN_ON(!work_done); - spin_lock(&todo_lock); + spin_lock_bh(&todo_lock); } - spin_unlock(&todo_lock); + spin_unlock_bh(&todo_lock); } void ieee80211_key_todo(void) -- GitLab From 518ff04fd84290a7ad9042e8a46d78d29cb443d3 Mon Sep 17 00:00:00 2001 From: "John W. Linville" Date: Mon, 17 Aug 2009 12:09:26 -0400 Subject: [PATCH 1181/1342] orinoco: correct key bounds check in orinoco_hw_get_tkip_iv If key is 4 that is an array out of bounds. Reported-by: Dan Carpenter Signed-off-by: John W. Linville --- drivers/net/wireless/orinoco/hw.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/wireless/orinoco/hw.c b/drivers/net/wireless/orinoco/hw.c index 632fac86a30..b3946272c72 100644 --- a/drivers/net/wireless/orinoco/hw.c +++ b/drivers/net/wireless/orinoco/hw.c @@ -70,7 +70,7 @@ int orinoco_hw_get_tkip_iv(struct orinoco_private *priv, int key, u8 *tsc) int err = 0; u8 tsc_arr[4][IW_ENCODE_SEQ_MAX_SIZE]; - if ((key < 0) || (key > 4)) + if ((key < 0) || (key >= 4)) return -EINVAL; err = hermes_read_ltv(hw, USER_BAP, HERMES_RID_CURRENT_TKIP_IV, -- GitLab From ada508274b8698a33cb0e5bd037db0f9dc781795 Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Mon, 3 Aug 2009 18:24:21 +0200 Subject: [PATCH 1182/1342] ocfs2: Handle quota file corruption more gracefully ocfs2_read_virt_blocks() does BUG when we try to read a block from a file beyond its end. Since this can happen due to filesystem corruption, it is not really an appropriate answer. Make ocfs2_read_quota_block() check the condition and handle it by calling ocfs2_error() and returning EIO. [ Modified to print ip_blkno in the error - Joel ] Reported-by: Tristan Ye Signed-off-by: Jan Kara Signed-off-by: Joel Becker --- fs/ocfs2/quota_global.c | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/fs/ocfs2/quota_global.c b/fs/ocfs2/quota_global.c index bf7742d0ee3..44f2a5e1d04 100644 --- a/fs/ocfs2/quota_global.c +++ b/fs/ocfs2/quota_global.c @@ -23,6 +23,7 @@ #include "sysfile.h" #include "dlmglue.h" #include "uptodate.h" +#include "super.h" #include "quota.h" static struct workqueue_struct *ocfs2_quota_wq = NULL; @@ -114,6 +115,15 @@ int ocfs2_read_quota_block(struct inode *inode, u64 v_block, int rc = 0; struct buffer_head *tmp = *bh; + if (i_size_read(inode) >> inode->i_sb->s_blocksize_bits <= v_block) { + ocfs2_error(inode->i_sb, + "Quota file %llu is probably corrupted! Requested " + "to read block %Lu but file has size only %Lu\n", + (unsigned long long)OCFS2_I(inode)->ip_blkno, + (unsigned long long)v_block, + (unsigned long long)i_size_read(inode)); + return -EIO; + } rc = ocfs2_read_virt_blocks(inode, v_block, 1, &tmp, 0, ocfs2_validate_quota_block); if (rc) -- GitLab From 60e2ec48665b8495360ca4a6004c5cd52beb2bc1 Mon Sep 17 00:00:00 2001 From: Tao Ma Date: Wed, 12 Aug 2009 14:42:47 +0800 Subject: [PATCH 1183/1342] ocfs2: release the buffer head in ocfs2_do_truncate. In ocfs2_do_truncate, we forget to release last_eb_bh which will cause memleak. So call brelse in the end. Signed-off-by: Tao Ma Signed-off-by: Joel Becker --- fs/ocfs2/alloc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/ocfs2/alloc.c b/fs/ocfs2/alloc.c index f9a3e894266..ab513ddaeff 100644 --- a/fs/ocfs2/alloc.c +++ b/fs/ocfs2/alloc.c @@ -6851,7 +6851,7 @@ static int ocfs2_do_truncate(struct ocfs2_super *osb, } status = 0; bail: - + brelse(last_eb_bh); mlog_exit(status); return status; } -- GitLab From eef3a116be11d35396efb2a8cc7345fd3221e294 Mon Sep 17 00:00:00 2001 From: Eric Paris Date: Sun, 16 Aug 2009 21:51:44 -0400 Subject: [PATCH 1184/1342] notify: unused event private race inotify decides if private data it passed to get added to an event was used by checking list_empty(). But it's possible that the event may have been dequeued and the private event removed so it would look empty. The fix is to use the return code from fsnotify_add_notify_event rather than looking at the list. Signed-off-by: Eric Paris Signed-off-by: Linus Torvalds --- fs/notify/inotify/inotify_fsnotify.c | 13 +++++++------ fs/notify/inotify/inotify_user.c | 7 +++---- fs/notify/notification.c | 7 +++---- 3 files changed, 13 insertions(+), 14 deletions(-) diff --git a/fs/notify/inotify/inotify_fsnotify.c b/fs/notify/inotify/inotify_fsnotify.c index 47cd258fd24..5dcbafe72d7 100644 --- a/fs/notify/inotify/inotify_fsnotify.c +++ b/fs/notify/inotify/inotify_fsnotify.c @@ -62,13 +62,14 @@ static int inotify_handle_event(struct fsnotify_group *group, struct fsnotify_ev event_priv->wd = wd; ret = fsnotify_add_notify_event(group, event, fsn_event_priv); - /* EEXIST is not an error */ - if (ret == -EEXIST) - ret = 0; - - /* did event_priv get attached? */ - if (list_empty(&fsn_event_priv->event_list)) + if (ret) { inotify_free_event_priv(fsn_event_priv); + /* EEXIST says we tail matched, EOVERFLOW isn't something + * to report up the stack. */ + if ((ret == -EEXIST) || + (ret == -EOVERFLOW)) + ret = 0; + } /* * If we hold the entry until after the event is on the queue diff --git a/fs/notify/inotify/inotify_user.c b/fs/notify/inotify/inotify_user.c index f30d9bbc2e1..c172a7a17b1 100644 --- a/fs/notify/inotify/inotify_user.c +++ b/fs/notify/inotify/inotify_user.c @@ -386,6 +386,7 @@ void inotify_ignored_and_remove_idr(struct fsnotify_mark_entry *entry, struct fsnotify_event *ignored_event; struct inotify_event_private_data *event_priv; struct fsnotify_event_private_data *fsn_event_priv; + int ret; ignored_event = fsnotify_create_event(NULL, FS_IN_IGNORED, NULL, FSNOTIFY_EVENT_NONE, NULL, 0, @@ -404,10 +405,8 @@ void inotify_ignored_and_remove_idr(struct fsnotify_mark_entry *entry, fsn_event_priv->group = group; event_priv->wd = ientry->wd; - fsnotify_add_notify_event(group, ignored_event, fsn_event_priv); - - /* did the private data get added? */ - if (list_empty(&fsn_event_priv->event_list)) + ret = fsnotify_add_notify_event(group, ignored_event, fsn_event_priv); + if (ret) inotify_free_event_priv(fsn_event_priv); skip_send_ignore: diff --git a/fs/notify/notification.c b/fs/notify/notification.c index 521368574e9..74b3cf30bc6 100644 --- a/fs/notify/notification.c +++ b/fs/notify/notification.c @@ -171,9 +171,7 @@ int fsnotify_add_notify_event(struct fsnotify_group *group, struct fsnotify_even struct list_head *list = &group->notification_list; struct fsnotify_event_holder *last_holder; struct fsnotify_event *last_event; - - /* easy to tell if priv was attached to the event */ - INIT_LIST_HEAD(&priv->event_list); + int ret = 0; /* * There is one fsnotify_event_holder embedded inside each fsnotify_event. @@ -194,6 +192,7 @@ alloc_holder: if (group->q_len >= group->max_events) { event = &q_overflow_event; + ret = -EOVERFLOW; /* sorry, no private data on the overflow event */ priv = NULL; } @@ -235,7 +234,7 @@ alloc_holder: mutex_unlock(&group->notification_mutex); wake_up(&group->notification_waitq); - return 0; + return ret; } /* -- GitLab From cd94c8bbef8d4b796a7ed4c551355a334604fd36 Mon Sep 17 00:00:00 2001 From: Eric Paris Date: Sun, 16 Aug 2009 21:51:49 -0400 Subject: [PATCH 1185/1342] inotify: tail drop inotify q_overflow events In f44aebcc the tail drop logic of events with no file backing (q_overflow and in_ignored) was reversed so IN_IGNORED events would never be tail dropped. This now means that Q_OVERFLOW events are NOT tail dropped. The fix is to not tail drop IN_IGNORED, but to tail drop Q_OVERFLOW. Signed-off-by: Eric Paris Signed-off-by: Linus Torvalds --- fs/notify/notification.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/fs/notify/notification.c b/fs/notify/notification.c index 74b3cf30bc6..3816d5750dd 100644 --- a/fs/notify/notification.c +++ b/fs/notify/notification.c @@ -153,6 +153,10 @@ static bool event_compare(struct fsnotify_event *old, struct fsnotify_event *new return true; break; case (FSNOTIFY_EVENT_NONE): + if (old->mask & FS_Q_OVERFLOW) + return true; + else if (old->mask & FS_IN_IGNORED) + return false; return false; }; } -- GitLab From 08e53fcb0db34baca3db84a457b6d67faabee4c6 Mon Sep 17 00:00:00 2001 From: Eric Paris Date: Sun, 16 Aug 2009 21:51:55 -0400 Subject: [PATCH 1186/1342] inotify: start watch descriptor count at 1 The inotify_add_watch man page specifies that inotify_add_watch() will return a non-negative integer. However, historically the inotify watches started at 1, not at 0. Turns out that the inotifywait program provided by the inotify-tools package doesn't properly handle a 0 watch descriptor. In 7e790dd5 we changed from starting at 1 to starting at 0. This patch starts at 1, just like in previous kernels, but also just like in previous kernels it's possible for it to wrap back to 0. This preserves the kernel functionality exactly like it was before the patch (neither method broke the spec) Signed-off-by: Eric Paris Signed-off-by: Linus Torvalds --- fs/notify/inotify/inotify_user.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/notify/inotify/inotify_user.c b/fs/notify/inotify/inotify_user.c index c172a7a17b1..dc32ed8323b 100644 --- a/fs/notify/inotify/inotify_user.c +++ b/fs/notify/inotify/inotify_user.c @@ -567,7 +567,7 @@ static struct fsnotify_group *inotify_new_group(struct user_struct *user, unsign spin_lock_init(&group->inotify_data.idr_lock); idr_init(&group->inotify_data.idr); - group->inotify_data.last_wd = 0; + group->inotify_data.last_wd = 1; group->inotify_data.user = user; group->inotify_data.fa = NULL; -- GitLab From 1adcaafe7414c5731f758b158aa0525057225deb Mon Sep 17 00:00:00 2001 From: Suresh Siddha Date: Mon, 17 Aug 2009 13:23:50 -0700 Subject: [PATCH 1187/1342] x86, pat: Allow ISA memory range uncacheable mapping requests Max Vozeler reported: > Bug 13877 - bogl-term broken with CONFIG_X86_PAT=y, works with =n > > strace of bogl-term: > 814 mmap2(NULL, 65536, PROT_READ|PROT_WRITE, MAP_SHARED, 4, 0) > = -1 EAGAIN (Resource temporarily unavailable) > 814 write(2, "bogl: mmaping /dev/fb0: Resource temporarily unavailable\n", > 57) = 57 PAT code maps the ISA memory range as WB in the PAT attribute, so that fixed range MTRR registers define the actual memory type (UC/WC/WT etc). But the upper level is_new_memtype_allowed() API checks are failing, as the request here is for UC and the return tracked type is WB (Tracked type is WB as MTRR type for this legacy range potentially will be different for each 4k page). Fix is_new_memtype_allowed() by always succeeding the ISA address range checks, as the null PAT (WB) and def MTRR fixed range register settings satisfy the memory type needs of the applications that map the ISA address range. Reported-and-Tested-by: Max Vozeler Signed-off-by: Suresh Siddha Signed-off-by: Venkatesh Pallipadi Signed-off-by: H. Peter Anvin --- arch/x86/include/asm/pgtable.h | 12 ++++++++++-- arch/x86/mm/pat.c | 3 ++- 2 files changed, 12 insertions(+), 3 deletions(-) diff --git a/arch/x86/include/asm/pgtable.h b/arch/x86/include/asm/pgtable.h index 3cc06e3fceb..16748077559 100644 --- a/arch/x86/include/asm/pgtable.h +++ b/arch/x86/include/asm/pgtable.h @@ -2,6 +2,7 @@ #define _ASM_X86_PGTABLE_H #include +#include #include @@ -269,9 +270,16 @@ static inline pgprot_t pgprot_modify(pgprot_t oldprot, pgprot_t newprot) #define canon_pgprot(p) __pgprot(massage_pgprot(p)) -static inline int is_new_memtype_allowed(unsigned long flags, - unsigned long new_flags) +static inline int is_new_memtype_allowed(u64 paddr, unsigned long size, + unsigned long flags, + unsigned long new_flags) { + /* + * PAT type is always WB for ISA. So no need to check. + */ + if (is_ISA_range(paddr, paddr + size - 1)) + return 1; + /* * Certain new memtypes are not allowed with certain * requested memtype: diff --git a/arch/x86/mm/pat.c b/arch/x86/mm/pat.c index e6718bb2806..352aa9e927e 100644 --- a/arch/x86/mm/pat.c +++ b/arch/x86/mm/pat.c @@ -623,7 +623,8 @@ static int reserve_pfn_range(u64 paddr, unsigned long size, pgprot_t *vma_prot, return ret; if (flags != want_flags) { - if (strict_prot || !is_new_memtype_allowed(want_flags, flags)) { + if (strict_prot || + !is_new_memtype_allowed(paddr, size, want_flags, flags)) { free_memtype(paddr, paddr + size); printk(KERN_ERR "%s:%d map pfn expected mapping type %s" " for %Lx-%Lx, got %s\n", -- GitLab From 50fb6d2bd7062708892ae7147f30c3ee905b7a3d Mon Sep 17 00:00:00 2001 From: Abhishek Kulkarni Date: Sun, 19 Jul 2009 13:41:57 -0600 Subject: [PATCH 1188/1342] 9p: Check for error in return value of v9fs_fid_add Check if v9fs_fid_add was successful or not based on its return value. Signed-off-by: Abhishek Kulkarni Signed-off-by: Eric Van Hensbergen --- fs/9p/vfs_inode.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/fs/9p/vfs_inode.c b/fs/9p/vfs_inode.c index 81f8bbf12f9..1fa5f15eadd 100644 --- a/fs/9p/vfs_inode.c +++ b/fs/9p/vfs_inode.c @@ -470,7 +470,10 @@ v9fs_create(struct v9fs_session_info *v9ses, struct inode *dir, dentry->d_op = &v9fs_dentry_operations; d_instantiate(dentry, inode); - v9fs_fid_add(dentry, fid); + err = v9fs_fid_add(dentry, fid); + if (err < 0) + goto error; + return ofid; error: -- GitLab From 2bb541157fe2602af7b9952096d0524f6f9c1e73 Mon Sep 17 00:00:00 2001 From: Abhishek Kulkarni Date: Sun, 19 Jul 2009 13:41:56 -0600 Subject: [PATCH 1189/1342] 9p: Fix possible inode leak in v9fs_get_inode. Add a missing iput when cleaning up if v9fs_get_inode fails after returning a valid inode. Signed-off-by: Abhishek Kulkarni Signed-off-by: Eric Van Hensbergen --- fs/9p/vfs_inode.c | 105 ++++++++++++++++++++++++---------------------- 1 file changed, 56 insertions(+), 49 deletions(-) diff --git a/fs/9p/vfs_inode.c b/fs/9p/vfs_inode.c index 1fa5f15eadd..0c8af1abf60 100644 --- a/fs/9p/vfs_inode.c +++ b/fs/9p/vfs_inode.c @@ -207,65 +207,72 @@ v9fs_blank_wstat(struct p9_wstat *wstat) struct inode *v9fs_get_inode(struct super_block *sb, int mode) { + int err; struct inode *inode; struct v9fs_session_info *v9ses = sb->s_fs_info; P9_DPRINTK(P9_DEBUG_VFS, "super block: %p mode: %o\n", sb, mode); inode = new_inode(sb); - if (inode) { - inode->i_mode = mode; - inode->i_uid = current_fsuid(); - inode->i_gid = current_fsgid(); - inode->i_blocks = 0; - inode->i_rdev = 0; - inode->i_atime = inode->i_mtime = inode->i_ctime = CURRENT_TIME; - inode->i_mapping->a_ops = &v9fs_addr_operations; - - switch (mode & S_IFMT) { - case S_IFIFO: - case S_IFBLK: - case S_IFCHR: - case S_IFSOCK: - if (!v9fs_extended(v9ses)) { - P9_DPRINTK(P9_DEBUG_ERROR, - "special files without extended mode\n"); - return ERR_PTR(-EINVAL); - } - init_special_inode(inode, inode->i_mode, - inode->i_rdev); - break; - case S_IFREG: - inode->i_op = &v9fs_file_inode_operations; - inode->i_fop = &v9fs_file_operations; - break; - case S_IFLNK: - if (!v9fs_extended(v9ses)) { - P9_DPRINTK(P9_DEBUG_ERROR, - "extended modes used w/o 9P2000.u\n"); - return ERR_PTR(-EINVAL); - } - inode->i_op = &v9fs_symlink_inode_operations; - break; - case S_IFDIR: - inc_nlink(inode); - if (v9fs_extended(v9ses)) - inode->i_op = &v9fs_dir_inode_operations_ext; - else - inode->i_op = &v9fs_dir_inode_operations; - inode->i_fop = &v9fs_dir_operations; - break; - default: + if (!inode) { + P9_EPRINTK(KERN_WARNING, "Problem allocating inode\n"); + return -ENOMEM; + } + + inode->i_mode = mode; + inode->i_uid = current_fsuid(); + inode->i_gid = current_fsgid(); + inode->i_blocks = 0; + inode->i_rdev = 0; + inode->i_atime = inode->i_mtime = inode->i_ctime = CURRENT_TIME; + inode->i_mapping->a_ops = &v9fs_addr_operations; + + switch (mode & S_IFMT) { + case S_IFIFO: + case S_IFBLK: + case S_IFCHR: + case S_IFSOCK: + if (!v9fs_extended(v9ses)) { P9_DPRINTK(P9_DEBUG_ERROR, - "BAD mode 0x%x S_IFMT 0x%x\n", - mode, mode & S_IFMT); - return ERR_PTR(-EINVAL); + "special files without extended mode\n"); + err = -EINVAL; + goto error; } - } else { - P9_EPRINTK(KERN_WARNING, "Problem allocating inode\n"); - return ERR_PTR(-ENOMEM); + init_special_inode(inode, inode->i_mode, inode->i_rdev); + break; + case S_IFREG: + inode->i_op = &v9fs_file_inode_operations; + inode->i_fop = &v9fs_file_operations; + break; + case S_IFLNK: + if (!v9fs_extended(v9ses)) { + P9_DPRINTK(P9_DEBUG_ERROR, + "extended modes used w/o 9P2000.u\n"); + err = -EINVAL; + goto error; + } + inode->i_op = &v9fs_symlink_inode_operations; + break; + case S_IFDIR: + inc_nlink(inode); + if (v9fs_extended(v9ses)) + inode->i_op = &v9fs_dir_inode_operations_ext; + else + inode->i_op = &v9fs_dir_inode_operations; + inode->i_fop = &v9fs_dir_operations; + break; + default: + P9_DPRINTK(P9_DEBUG_ERROR, "BAD mode 0x%x S_IFMT 0x%x\n", + mode, mode & S_IFMT); + err = -EINVAL; + goto error; } + return inode; + +error: + iput(inode); + return ERR_PTR(err); } /* -- GitLab From 0e15597ebfe00e28857185f46aba00f400480ffe Mon Sep 17 00:00:00 2001 From: Abhishek Kulkarni Date: Sun, 19 Jul 2009 13:41:55 -0600 Subject: [PATCH 1190/1342] 9p: minor comment fixes Fix the comments -- mostly the improper and/or missing descriptions of function parameters. Signed-off-by: Abhishek Kulkarni Signed-off-by: Eric Van Hensbergen --- fs/9p/vfs_inode.c | 3 +-- net/9p/client.c | 14 +++++++------- net/9p/trans_fd.c | 8 ++++---- net/9p/trans_rdma.c | 9 +++++---- net/9p/trans_virtio.c | 11 ++++------- 5 files changed, 21 insertions(+), 24 deletions(-) diff --git a/fs/9p/vfs_inode.c b/fs/9p/vfs_inode.c index 0c8af1abf60..f22668afd0d 100644 --- a/fs/9p/vfs_inode.c +++ b/fs/9p/vfs_inode.c @@ -171,7 +171,6 @@ int v9fs_uflags2omode(int uflags, int extended) /** * v9fs_blank_wstat - helper function to setup a 9P stat structure - * @v9ses: 9P session info (for determining extended mode) * @wstat: structure to initialize * */ @@ -410,9 +409,9 @@ v9fs_open_created(struct inode *inode, struct file *file) * @v9ses: session information * @dir: directory that dentry is being created in * @dentry: dentry that is being created + * @extension: 9p2000.u extension string to support devices, etc. * @perm: create permissions * @mode: open mode - * @extension: 9p2000.u extension string to support devices, etc. * */ static struct p9_fid * diff --git a/net/9p/client.c b/net/9p/client.c index 787ccddb85e..7bbd2d5ae8d 100644 --- a/net/9p/client.c +++ b/net/9p/client.c @@ -60,9 +60,9 @@ static struct p9_req_t * p9_client_rpc(struct p9_client *c, int8_t type, const char *fmt, ...); /** - * v9fs_parse_options - parse mount options into session structure - * @options: options string passed from mount - * @v9ses: existing v9fs session information + * parse_options - parse mount options into client structure + * @opts: options string passed from mount + * @clnt: existing v9fs client information * * Return 0 upon success, -ERRNO upon failure */ @@ -232,7 +232,7 @@ EXPORT_SYMBOL(p9_tag_lookup); /** * p9_tag_init - setup tags structure and contents - * @tags: tags structure from the client struct + * @c: v9fs client struct * * This initializes the tags structure for each client instance. * @@ -258,7 +258,7 @@ error: /** * p9_tag_cleanup - cleans up tags structure and reclaims resources - * @tags: tags structure from the client struct + * @c: v9fs client struct * * This frees resources associated with the tags structure * @@ -430,8 +430,8 @@ static int p9_check_errors(struct p9_client *c, struct p9_req_t *req) /** * p9_client_flush - flush (cancel) a request - * c: client state - * req: request to cancel + * @c: client state + * @oldreq: request to cancel * * This sents a flush for a particular requests and links * the flush request to the original request. The current diff --git a/net/9p/trans_fd.c b/net/9p/trans_fd.c index 8c2588e4edc..8d934dd7fd5 100644 --- a/net/9p/trans_fd.c +++ b/net/9p/trans_fd.c @@ -119,8 +119,8 @@ struct p9_poll_wait { * @wpos: write position for current frame * @wsize: amount of data to write for current frame * @wbuf: current write buffer + * @poll_pending_link: pending links to be polled per conn * @poll_wait: array of wait_q's for various worker threads - * @poll_waddr: ???? * @pt: poll state * @rq: current read work * @wq: current write work @@ -700,9 +700,9 @@ static int p9_fd_cancel(struct p9_client *client, struct p9_req_t *req) } /** - * parse_options - parse mount options into session structure - * @options: options string passed from mount - * @opts: transport-specific structure to parse options into + * parse_opts - parse mount options into p9_fd_opts structure + * @params: options string passed from mount + * @opts: fd transport-specific structure to parse options into * * Returns 0 upon success, -ERRNO upon failure */ diff --git a/net/9p/trans_rdma.c b/net/9p/trans_rdma.c index ac4990041eb..65cb29db03f 100644 --- a/net/9p/trans_rdma.c +++ b/net/9p/trans_rdma.c @@ -67,14 +67,15 @@ * @pd: Protection Domain pointer * @qp: Queue Pair pointer * @cq: Completion Queue pointer + * @dm_mr: DMA Memory Region pointer * @lkey: The local access only memory region key * @timeout: Number of uSecs to wait for connection management events * @sq_depth: The depth of the Send Queue * @sq_sem: Semaphore for the SQ * @rq_depth: The depth of the Receive Queue. + * @rq_count: Count of requests in the Receive Queue. * @addr: The remote peer's address * @req_lock: Protects the active request list - * @send_wait: Wait list when the SQ fills up * @cm_done: Completion event for connection management tracking */ struct p9_trans_rdma { @@ -154,9 +155,9 @@ static match_table_t tokens = { }; /** - * parse_options - parse mount options into session structure - * @options: options string passed from mount - * @opts: transport-specific structure to parse options into + * parse_opts - parse mount options into rdma options structure + * @params: options string passed from mount + * @opts: rdma transport-specific structure to parse options into * * Returns 0 upon success, -ERRNO upon failure */ diff --git a/net/9p/trans_virtio.c b/net/9p/trans_virtio.c index a49484e67e1..9bf0b737aa5 100644 --- a/net/9p/trans_virtio.c +++ b/net/9p/trans_virtio.c @@ -57,11 +57,9 @@ static int chan_index; * @initialized: whether the channel is initialized * @inuse: whether the channel is in use * @lock: protects multiple elements within this structure + * @client: client instance * @vdev: virtio dev associated with this channel * @vq: virtio queue associated with this channel - * @tagpool: accounting for tag ids (and request slots) - * @reqs: array of request slots - * @max_tag: current number of request_slots allocated * @sg: scatter gather list which is used to pack a request (protected?) * * We keep all per-channel information in a structure. @@ -92,7 +90,7 @@ static unsigned int rest_of_page(void *data) /** * p9_virtio_close - reclaim resources of a channel - * @trans: transport state + * @client: client instance * * This reclaims a channel by freeing its resources and * reseting its inuse flag. @@ -181,9 +179,8 @@ static int p9_virtio_cancel(struct p9_client *client, struct p9_req_t *req) /** * p9_virtio_request - issue a request - * @t: transport state - * @tc: &p9_fcall request to transmit - * @rc: &p9_fcall to put reponse into + * @client: client instance issuing the request + * @req: request to be issued * */ -- GitLab From 02bc35672b2fdf251e264adca5407792f63191e4 Mon Sep 17 00:00:00 2001 From: Abhishek Kulkarni Date: Sun, 19 Jul 2009 13:41:54 -0600 Subject: [PATCH 1191/1342] 9p: Fix possible memleak in v9fs_inode_from fid. Add missing p9stat_free in v9fs_inode_from_fid to avoid any possible leaks. Signed-off-by: Abhishek Kulkarni Signed-off-by: Eric Van Hensbergen --- fs/9p/vfs_inode.c | 13 ++++--------- 1 file changed, 4 insertions(+), 9 deletions(-) diff --git a/fs/9p/vfs_inode.c b/fs/9p/vfs_inode.c index f22668afd0d..fac30d21851 100644 --- a/fs/9p/vfs_inode.c +++ b/fs/9p/vfs_inode.c @@ -344,30 +344,25 @@ v9fs_inode_from_fid(struct v9fs_session_info *v9ses, struct p9_fid *fid, ret = NULL; st = p9_client_stat(fid); - if (IS_ERR(st)) { - err = PTR_ERR(st); - st = NULL; - goto error; - } + if (IS_ERR(st)) + return ERR_CAST(st); umode = p9mode2unixmode(v9ses, st->mode); ret = v9fs_get_inode(sb, umode); if (IS_ERR(ret)) { err = PTR_ERR(ret); - ret = NULL; goto error; } v9fs_stat2inode(st, ret, sb); ret->i_ino = v9fs_qid2ino(&st->qid); + p9stat_free(st); kfree(st); return ret; error: + p9stat_free(st); kfree(st); - if (ret) - iput(ret); - return ERR_PTR(err); } -- GitLab From 4f4038328da5eb9cc237b51d3fe68138fd3fea14 Mon Sep 17 00:00:00 2001 From: Abhishek Kulkarni Date: Sun, 19 Jul 2009 13:41:53 -0600 Subject: [PATCH 1192/1342] 9p: Fix v9fs show_options Add the delimiter ',' before the options when they are passed and check if no option parameters are passed to prevent displaying NULL in /proc/mounts. Signed-off-by: Abhishek Kulkarni Signed-off-by: Eric Van Hensbergen --- fs/9p/vfs_super.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/fs/9p/vfs_super.c b/fs/9p/vfs_super.c index 38d695d66a0..a9d7d08cfbe 100644 --- a/fs/9p/vfs_super.c +++ b/fs/9p/vfs_super.c @@ -220,8 +220,8 @@ static void v9fs_kill_super(struct super_block *s) static int v9fs_show_options(struct seq_file *m, struct vfsmount *mnt) { struct v9fs_session_info *v9ses = mnt->mnt_sb->s_fs_info; - - seq_printf(m, "%s", v9ses->options); + if (v9ses->options != NULL) + seq_printf(m, ",%s", v9ses->options); return 0; } -- GitLab From 1b5ab3e86712b6be38ebbe0d821387c1d8f91d7c Mon Sep 17 00:00:00 2001 From: Abhishek Kulkarni Date: Sun, 19 Jul 2009 13:41:52 -0600 Subject: [PATCH 1193/1342] 9p: Fix possible regressions when ->get_sb fails. ->get_sb can fail causing some badness. this patch fixes * clear sb->fs_s_info in kill_sb. * deactivate_locked_super() calls kill_sb (v9fs_kill_super) which closes the destroys the client, clunks all its fids and closes the v9fs session. Attempting to do it twice will cause an oops. Signed-off-by: Abhishek Kulkarni Signed-off-by: Eric Van Hensbergen --- fs/9p/vfs_super.c | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-) diff --git a/fs/9p/vfs_super.c b/fs/9p/vfs_super.c index a9d7d08cfbe..2495af4ad9a 100644 --- a/fs/9p/vfs_super.c +++ b/fs/9p/vfs_super.c @@ -120,7 +120,6 @@ static int v9fs_get_sb(struct file_system_type *fs_type, int flags, P9_DPRINTK(P9_DEBUG_VFS, " \n"); - st = NULL; v9ses = kzalloc(sizeof(struct v9fs_session_info), GFP_KERNEL); if (!v9ses) return -ENOMEM; @@ -173,10 +172,8 @@ P9_DPRINTK(P9_DEBUG_VFS, " simple set mount, return 0\n"); simple_set_mnt(mnt, sb); return 0; -release_sb: - deactivate_locked_super(sb); - free_stat: + p9stat_free(st); kfree(st); clunk_fid: @@ -185,7 +182,12 @@ clunk_fid: close_session: v9fs_session_close(v9ses); kfree(v9ses); + return retval; +release_sb: + p9stat_free(st); + kfree(st); + deactivate_locked_super(sb); return retval; } @@ -207,6 +209,7 @@ static void v9fs_kill_super(struct super_block *s) v9fs_session_close(v9ses); kfree(v9ses); + s->s_fs_info = NULL; P9_DPRINTK(P9_DEBUG_VFS, "exiting kill_super\n"); } -- GitLab From 4d3297ca5bf37ff5956f76fb352e009880aad62d Mon Sep 17 00:00:00 2001 From: Abhishek Kulkarni Date: Sun, 19 Jul 2009 13:41:51 -0600 Subject: [PATCH 1194/1342] 9p: Remove redundant inode uid/gid assignment Remove a redundant update of inode's i_uid and i_gid after v9fs_get_inode() since the latter already sets up a new inode and sets the proper uid and gid values. Signed-off-by: Abhishek Kulkarni Signed-off-by: Eric Van Hensbergen --- fs/9p/vfs_super.c | 5 ----- 1 file changed, 5 deletions(-) diff --git a/fs/9p/vfs_super.c b/fs/9p/vfs_super.c index 2495af4ad9a..072dce09447 100644 --- a/fs/9p/vfs_super.c +++ b/fs/9p/vfs_super.c @@ -113,8 +113,6 @@ static int v9fs_get_sb(struct file_system_type *fs_type, int flags, struct v9fs_session_info *v9ses = NULL; struct p9_wstat *st = NULL; int mode = S_IRWXUGO | S_ISVTX; - uid_t uid = current_fsuid(); - gid_t gid = current_fsgid(); struct p9_fid *fid; int retval = 0; @@ -149,9 +147,6 @@ static int v9fs_get_sb(struct file_system_type *fs_type, int flags, goto release_sb; } - inode->i_uid = uid; - inode->i_gid = gid; - root = d_alloc_root(inode); if (!root) { iput(inode); -- GitLab From 5fd131893793567c361ae64cbeb28a2a753bbe35 Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Thu, 30 Jul 2009 17:01:53 +0200 Subject: [PATCH 1195/1342] ocfs2: Don't oops in ocfs2_kill_sb on a failed mount If we fail to mount the filesystem, we have to be careful not to dereference uninitialized structures in ocfs2_kill_sb. Signed-off-by: Jan Kara Signed-off-by: Joel Becker --- fs/ocfs2/super.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/fs/ocfs2/super.c b/fs/ocfs2/super.c index b0ee0fdf799..a3f8871d21f 100644 --- a/fs/ocfs2/super.c +++ b/fs/ocfs2/super.c @@ -1218,13 +1218,17 @@ static void ocfs2_kill_sb(struct super_block *sb) { struct ocfs2_super *osb = OCFS2_SB(sb); + /* Failed mount? */ + if (!osb || atomic_read(&osb->vol_state) == VOLUME_DISABLED) + goto out; + /* Prevent further queueing of inode drop events */ spin_lock(&dentry_list_lock); ocfs2_set_osb_flag(osb, OCFS2_OSB_DROP_DENTRY_LOCK_IMMED); spin_unlock(&dentry_list_lock); /* Wait for work to finish and/or remove it */ cancel_work_sync(&osb->dentry_lock_work); - +out: kill_block_super(sb); } -- GitLab From 48559b4c30708ebdc849483da9fb83ee08c6c908 Mon Sep 17 00:00:00 2001 From: Abhishek Kulkarni Date: Mon, 17 Aug 2009 16:32:18 -0500 Subject: [PATCH 1196/1342] 9p: Add missing cast for the error return value in v9fs_get_inode Cast the error return value (ENOMEM) in v9fs_get_inode() to its correct type using ERR_PTR. Signed-off-by: Abhishek Kulkarni Signed-off-by: Eric Van Hensbergen --- fs/9p/vfs_inode.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/9p/vfs_inode.c b/fs/9p/vfs_inode.c index fac30d21851..06a223d50a8 100644 --- a/fs/9p/vfs_inode.c +++ b/fs/9p/vfs_inode.c @@ -215,7 +215,7 @@ struct inode *v9fs_get_inode(struct super_block *sb, int mode) inode = new_inode(sb); if (!inode) { P9_EPRINTK(KERN_WARNING, "Problem allocating inode\n"); - return -ENOMEM; + return ERR_PTR(-ENOMEM); } inode->i_mode = mode; -- GitLab From 0aad37ef3deed118d3816e1d1a600eb2ec9dcb87 Mon Sep 17 00:00:00 2001 From: Abhishek Kulkarni Date: Mon, 17 Aug 2009 16:38:45 -0500 Subject: [PATCH 1197/1342] net/9p: insulate the client against an invalid error code sent by a 9p server A looney tunes server sending an invalid error code (which is !IS_ERR_VALUE) can result in a client oops. So fix it by adding a check and converting unknown or invalid error codes to -ESERVERFAULT. Signed-off-by: Abhishek Kulkarni Signed-off-by: Eric Van Hensbergen --- net/9p/client.c | 7 +------ net/9p/error.c | 2 +- 2 files changed, 2 insertions(+), 7 deletions(-) diff --git a/net/9p/client.c b/net/9p/client.c index 7bbd2d5ae8d..5bf5f227dbe 100644 --- a/net/9p/client.c +++ b/net/9p/client.c @@ -411,14 +411,9 @@ static int p9_check_errors(struct p9_client *c, struct p9_req_t *req) if (c->dotu) err = -ecode; - if (!err) { + if (!err || !IS_ERR_VALUE(err)) err = p9_errstr2errno(ename, strlen(ename)); - /* string match failed */ - if (!err) - err = -ESERVERFAULT; - } - P9_DPRINTK(P9_DEBUG_9P, "<<< RERROR (%d) %s\n", -ecode, ename); kfree(ename); diff --git a/net/9p/error.c b/net/9p/error.c index fdebe431406..52518512a93 100644 --- a/net/9p/error.c +++ b/net/9p/error.c @@ -239,7 +239,7 @@ int p9_errstr2errno(char *errstr, int len) errstr[len] = 0; printk(KERN_ERR "%s: server reported unknown error %s\n", __func__, errstr); - errno = 1; + errno = ESERVERFAULT; } return -errno; -- GitLab From 4b53e4b500779230aedd5355940aeaaed0b5353b Mon Sep 17 00:00:00 2001 From: Abhishek Kulkarni Date: Mon, 17 Aug 2009 16:42:28 -0500 Subject: [PATCH 1198/1342] 9p: remove unnecessary v9fses->options which duplicates the mount string The mount options string is saved in sb->s_options. This patch removes the redundant duplicating of the mount options. Also, since we are not displaying anything special in show options, we replace v9fs_show_options with generic_show_options for now. Signed-off-by: Abhishek Kulkarni Signed-off-by: Eric Van Hensbergen --- fs/9p/v9fs.c | 21 +++++---------------- fs/9p/v9fs.h | 1 - fs/9p/vfs_super.c | 23 +++++------------------ 3 files changed, 10 insertions(+), 35 deletions(-) diff --git a/fs/9p/v9fs.c b/fs/9p/v9fs.c index 332b5ff02fe..f7003cfac63 100644 --- a/fs/9p/v9fs.c +++ b/fs/9p/v9fs.c @@ -76,7 +76,7 @@ static const match_table_t tokens = { * Return 0 upon success, -ERRNO upon failure. */ -static int v9fs_parse_options(struct v9fs_session_info *v9ses) +static int v9fs_parse_options(struct v9fs_session_info *v9ses, char *opts) { char *options; substring_t args[MAX_OPT_ARGS]; @@ -90,10 +90,10 @@ static int v9fs_parse_options(struct v9fs_session_info *v9ses) v9ses->debug = 0; v9ses->cache = 0; - if (!v9ses->options) + if (!opts) return 0; - options = kstrdup(v9ses->options, GFP_KERNEL); + options = kstrdup(opts, GFP_KERNEL); if (!options) { P9_DPRINTK(P9_DEBUG_ERROR, "failed to allocate copy of option string\n"); @@ -206,24 +206,14 @@ struct p9_fid *v9fs_session_init(struct v9fs_session_info *v9ses, v9ses->uid = ~0; v9ses->dfltuid = V9FS_DEFUID; v9ses->dfltgid = V9FS_DEFGID; - if (data) { - v9ses->options = kstrdup(data, GFP_KERNEL); - if (!v9ses->options) { - P9_DPRINTK(P9_DEBUG_ERROR, - "failed to allocate copy of option string\n"); - retval = -ENOMEM; - goto error; - } - } - rc = v9fs_parse_options(v9ses); + rc = v9fs_parse_options(v9ses, data); if (rc < 0) { retval = rc; goto error; } - v9ses->clnt = p9_client_create(dev_name, v9ses->options); - + v9ses->clnt = p9_client_create(dev_name, data); if (IS_ERR(v9ses->clnt)) { retval = PTR_ERR(v9ses->clnt); v9ses->clnt = NULL; @@ -280,7 +270,6 @@ void v9fs_session_close(struct v9fs_session_info *v9ses) __putname(v9ses->uname); __putname(v9ses->aname); - kfree(v9ses->options); } /** diff --git a/fs/9p/v9fs.h b/fs/9p/v9fs.h index a7d56719299..38762bf102a 100644 --- a/fs/9p/v9fs.h +++ b/fs/9p/v9fs.h @@ -85,7 +85,6 @@ struct v9fs_session_info { unsigned int afid; unsigned int cache; - char *options; /* copy of mount options */ char *uname; /* user name to mount as */ char *aname; /* name of remote hierarchy being mounted */ unsigned int maxdata; /* max data for client interface */ diff --git a/fs/9p/vfs_super.c b/fs/9p/vfs_super.c index 072dce09447..8961f1a8f66 100644 --- a/fs/9p/vfs_super.c +++ b/fs/9p/vfs_super.c @@ -81,7 +81,7 @@ static int v9fs_set_super(struct super_block *s, void *data) static void v9fs_fill_super(struct super_block *sb, struct v9fs_session_info *v9ses, - int flags) + int flags, void *data) { sb->s_maxbytes = MAX_LFS_FILESIZE; sb->s_blocksize_bits = fls(v9ses->maxdata - 1); @@ -91,6 +91,8 @@ v9fs_fill_super(struct super_block *sb, struct v9fs_session_info *v9ses, sb->s_flags = flags | MS_ACTIVE | MS_SYNCHRONOUS | MS_DIRSYNC | MS_NOATIME; + + save_mount_options(sb, data); } /** @@ -139,7 +141,7 @@ static int v9fs_get_sb(struct file_system_type *fs_type, int flags, retval = PTR_ERR(sb); goto free_stat; } - v9fs_fill_super(sb, v9ses, flags); + v9fs_fill_super(sb, v9ses, flags, data); inode = v9fs_get_inode(sb, S_IFDIR | mode); if (IS_ERR(inode)) { @@ -208,21 +210,6 @@ static void v9fs_kill_super(struct super_block *s) P9_DPRINTK(P9_DEBUG_VFS, "exiting kill_super\n"); } -/** - * v9fs_show_options - Show mount options in /proc/mounts - * @m: seq_file to write to - * @mnt: mount descriptor - * - */ - -static int v9fs_show_options(struct seq_file *m, struct vfsmount *mnt) -{ - struct v9fs_session_info *v9ses = mnt->mnt_sb->s_fs_info; - if (v9ses->options != NULL) - seq_printf(m, ",%s", v9ses->options); - return 0; -} - static void v9fs_umount_begin(struct super_block *sb) { @@ -235,7 +222,7 @@ v9fs_umount_begin(struct super_block *sb) static const struct super_operations v9fs_super_ops = { .statfs = simple_statfs, .clear_inode = v9fs_clear_inode, - .show_options = v9fs_show_options, + .show_options = generic_show_options, .umount_begin = v9fs_umount_begin, }; -- GitLab From 7815f4be4026b6c5027058102ae67a4b9feffa5f Mon Sep 17 00:00:00 2001 From: Eric Van Hensbergen Date: Mon, 17 Aug 2009 16:49:44 -0500 Subject: [PATCH 1199/1342] 9p: update documentation pointers Signed-off-by: Eric Van Hensbergen --- Documentation/filesystems/9p.txt | 3 +++ 1 file changed, 3 insertions(+) diff --git a/Documentation/filesystems/9p.txt b/Documentation/filesystems/9p.txt index bf8080640eb..6208f55c44c 100644 --- a/Documentation/filesystems/9p.txt +++ b/Documentation/filesystems/9p.txt @@ -123,6 +123,9 @@ available from the same CVS repository. There are user and developer mailing lists available through the v9fs project on sourceforge (http://sourceforge.net/projects/v9fs). +A stand-alone version of the module (which should build for any 2.6 kernel) +is available via (http://github.com/ericvh/9p-sac/tree/master) + News and other information is maintained on SWiK (http://swik.net/v9fs). Bug reports may be issued through the kernel.org bugzilla -- GitLab From f2d84b65b9778e8a35dd904f7d3993f0a60c9756 Mon Sep 17 00:00:00 2001 From: Zhaolei Date: Fri, 7 Aug 2009 18:55:48 +0800 Subject: [PATCH 1200/1342] ftrace: Unify effect of writing to trace_options and option/* "echo noglobal-clock > trace_options" can be used to change trace clock but "echo 0 > options/global-clock" can't. The flag toggling will be silently accepted without actually changing the clock callback. We can fix it by using set_tracer_flags() in trace_options_core_write(). Changelog: v1->v2: Simplified switch() after Li Zefan 's suggestion Signed-off-by: Zhao Lei Cc: Steven Rostedt Cc: Li Zefan Signed-off-by: Frederic Weisbecker --- kernel/trace/trace.c | 12 ++---------- 1 file changed, 2 insertions(+), 10 deletions(-) diff --git a/kernel/trace/trace.c b/kernel/trace/trace.c index c22b40f8f57..8c358395d33 100644 --- a/kernel/trace/trace.c +++ b/kernel/trace/trace.c @@ -3896,17 +3896,9 @@ trace_options_core_write(struct file *filp, const char __user *ubuf, size_t cnt, if (ret < 0) return ret; - switch (val) { - case 0: - trace_flags &= ~(1 << index); - break; - case 1: - trace_flags |= 1 << index; - break; - - default: + if (val != 0 && val != 1) return -EINVAL; - } + set_tracer_flags(1 << index, val); *ppos += cnt; -- GitLab From 80ffb3cceaefa405f2ecd46d66500ed8d53efe74 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Tue, 18 Aug 2009 10:35:26 +1000 Subject: [PATCH 1201/1342] Fix new incorrect error return from do_md_stop. Recent commit c8c00a6915a2e3d10416e8bdd3138429beb96210 changed the exit paths in do_md_stop and was not quite careful enough. There is one path were 'err' now needs to be cleared but it isn't. So setting an array to readonly (with mdadm --readonly) will work, but will incorrectly report and error: ENXIO. Signed-off-by: NeilBrown --- drivers/md/md.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/md/md.c b/drivers/md/md.c index 103f2d33fa8..9dd872000ce 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -4364,6 +4364,7 @@ static int do_md_stop(mddev_t * mddev, int mode, int is_open) if (mode == 1) set_disk_ro(disk, 1); clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery); + err = 0; } out: mutex_unlock(&mddev->open_mutex); -- GitLab From c6ba973b8fa97422aab4204f7d79f1d413cde925 Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Mon, 17 Aug 2009 18:05:32 -0700 Subject: [PATCH 1202/1342] NETROM: Fix use of static buffer The static variable used by nr_call_to_digi might result in corruption if multiple threads are trying to usee a node or neighbour via ioctl. Fixed by having the caller pass a structure in. This is safe because nr_add_node rsp. nr_add_neigh will allocate a permanent structure, if needed. Signed-off-by: Ralf Baechle Signed-off-by: David S. Miller --- net/netrom/nr_route.c | 21 ++++++++++++--------- 1 file changed, 12 insertions(+), 9 deletions(-) diff --git a/net/netrom/nr_route.c b/net/netrom/nr_route.c index e943c16552a..4eb1ac9a767 100644 --- a/net/netrom/nr_route.c +++ b/net/netrom/nr_route.c @@ -630,23 +630,23 @@ out: return dev; } -static ax25_digi *nr_call_to_digi(int ndigis, ax25_address *digipeaters) +static ax25_digi *nr_call_to_digi(ax25_digi *digi, int ndigis, + ax25_address *digipeaters) { - static ax25_digi ax25_digi; int i; if (ndigis == 0) return NULL; for (i = 0; i < ndigis; i++) { - ax25_digi.calls[i] = digipeaters[i]; - ax25_digi.repeated[i] = 0; + digi->calls[i] = digipeaters[i]; + digi->repeated[i] = 0; } - ax25_digi.ndigi = ndigis; - ax25_digi.lastrepeat = -1; + digi->ndigi = ndigis; + digi->lastrepeat = -1; - return &ax25_digi; + return digi; } /* @@ -656,6 +656,7 @@ int nr_rt_ioctl(unsigned int cmd, void __user *arg) { struct nr_route_struct nr_route; struct net_device *dev; + ax25_digi digi; int ret; switch (cmd) { @@ -673,13 +674,15 @@ int nr_rt_ioctl(unsigned int cmd, void __user *arg) ret = nr_add_node(&nr_route.callsign, nr_route.mnemonic, &nr_route.neighbour, - nr_call_to_digi(nr_route.ndigis, nr_route.digipeaters), + nr_call_to_digi(&digi, nr_route.ndigis, + nr_route.digipeaters), dev, nr_route.quality, nr_route.obs_count); break; case NETROM_NEIGH: ret = nr_add_neigh(&nr_route.callsign, - nr_call_to_digi(nr_route.ndigis, nr_route.digipeaters), + nr_call_to_digi(&digi, nr_route.ndigis, + nr_route.digipeaters), dev, nr_route.quality); break; default: -- GitLab From c1a8f1f1c8e01eab5862c8db39b49ace814e6c66 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Sun, 16 Aug 2009 09:36:49 +0000 Subject: [PATCH 1203/1342] net: restore gnet_stats_basic to previous definition In 5e140dfc1fe87eae27846f193086724806b33c7d "net: reorder struct Qdisc for better SMP performance" the definition of struct gnet_stats_basic changed incompatibly, as copies of this struct are shipped to userland via netlink. Restoring old behavior is not welcome, for performance reason. Fix is to use a private structure for kernel, and teach gnet_stats_copy_basic() to convert from kernel to user land, using legacy structure (struct gnet_stats_basic) Based on a report and initial patch from Michael Spang. Reported-by: Michael Spang Signed-off-by: Eric Dumazet Signed-off-by: David S. Miller --- include/linux/gen_stats.h | 5 +++++ include/net/act_api.h | 2 +- include/net/gen_stats.h | 10 +++++----- include/net/netfilter/xt_rateest.h | 2 +- include/net/sch_generic.h | 2 +- net/core/gen_estimator.c | 12 ++++++------ net/core/gen_stats.c | 11 ++++++++--- net/netfilter/xt_RATEEST.c | 2 +- net/sched/sch_atm.c | 2 +- net/sched/sch_cbq.c | 2 +- net/sched/sch_drr.c | 2 +- net/sched/sch_hfsc.c | 2 +- net/sched/sch_htb.c | 2 +- 13 files changed, 33 insertions(+), 23 deletions(-) diff --git a/include/linux/gen_stats.h b/include/linux/gen_stats.h index 0ffa41df0ee..710e901085d 100644 --- a/include/linux/gen_stats.h +++ b/include/linux/gen_stats.h @@ -19,6 +19,11 @@ enum { * @packets: number of seen packets */ struct gnet_stats_basic +{ + __u64 bytes; + __u32 packets; +}; +struct gnet_stats_basic_packed { __u64 bytes; __u32 packets; diff --git a/include/net/act_api.h b/include/net/act_api.h index 565eed8fe49..c05fd717c58 100644 --- a/include/net/act_api.h +++ b/include/net/act_api.h @@ -16,7 +16,7 @@ struct tcf_common { u32 tcfc_capab; int tcfc_action; struct tcf_t tcfc_tm; - struct gnet_stats_basic tcfc_bstats; + struct gnet_stats_basic_packed tcfc_bstats; struct gnet_stats_queue tcfc_qstats; struct gnet_stats_rate_est tcfc_rate_est; spinlock_t tcfc_lock; diff --git a/include/net/gen_stats.h b/include/net/gen_stats.h index d136b5240ef..c1488553e34 100644 --- a/include/net/gen_stats.h +++ b/include/net/gen_stats.h @@ -28,7 +28,7 @@ extern int gnet_stats_start_copy_compat(struct sk_buff *skb, int type, spinlock_t *lock, struct gnet_dump *d); extern int gnet_stats_copy_basic(struct gnet_dump *d, - struct gnet_stats_basic *b); + struct gnet_stats_basic_packed *b); extern int gnet_stats_copy_rate_est(struct gnet_dump *d, struct gnet_stats_rate_est *r); extern int gnet_stats_copy_queue(struct gnet_dump *d, @@ -37,14 +37,14 @@ extern int gnet_stats_copy_app(struct gnet_dump *d, void *st, int len); extern int gnet_stats_finish_copy(struct gnet_dump *d); -extern int gen_new_estimator(struct gnet_stats_basic *bstats, +extern int gen_new_estimator(struct gnet_stats_basic_packed *bstats, struct gnet_stats_rate_est *rate_est, spinlock_t *stats_lock, struct nlattr *opt); -extern void gen_kill_estimator(struct gnet_stats_basic *bstats, +extern void gen_kill_estimator(struct gnet_stats_basic_packed *bstats, struct gnet_stats_rate_est *rate_est); -extern int gen_replace_estimator(struct gnet_stats_basic *bstats, +extern int gen_replace_estimator(struct gnet_stats_basic_packed *bstats, struct gnet_stats_rate_est *rate_est, spinlock_t *stats_lock, struct nlattr *opt); -extern bool gen_estimator_active(const struct gnet_stats_basic *bstats, +extern bool gen_estimator_active(const struct gnet_stats_basic_packed *bstats, const struct gnet_stats_rate_est *rate_est); #endif diff --git a/include/net/netfilter/xt_rateest.h b/include/net/netfilter/xt_rateest.h index 65d594dffbf..ddbf37e1961 100644 --- a/include/net/netfilter/xt_rateest.h +++ b/include/net/netfilter/xt_rateest.h @@ -8,7 +8,7 @@ struct xt_rateest { spinlock_t lock; struct gnet_estimator params; struct gnet_stats_rate_est rstats; - struct gnet_stats_basic bstats; + struct gnet_stats_basic_packed bstats; }; extern struct xt_rateest *xt_rateest_lookup(const char *name); diff --git a/include/net/sch_generic.h b/include/net/sch_generic.h index 964ffa0d881..5482e9582f5 100644 --- a/include/net/sch_generic.h +++ b/include/net/sch_generic.h @@ -72,7 +72,7 @@ struct Qdisc */ unsigned long state; struct sk_buff_head q; - struct gnet_stats_basic bstats; + struct gnet_stats_basic_packed bstats; struct gnet_stats_queue qstats; }; diff --git a/net/core/gen_estimator.c b/net/core/gen_estimator.c index 78e5bfc454a..493775f4f2f 100644 --- a/net/core/gen_estimator.c +++ b/net/core/gen_estimator.c @@ -81,7 +81,7 @@ struct gen_estimator { struct list_head list; - struct gnet_stats_basic *bstats; + struct gnet_stats_basic_packed *bstats; struct gnet_stats_rate_est *rate_est; spinlock_t *stats_lock; int ewma_log; @@ -165,7 +165,7 @@ static void gen_add_node(struct gen_estimator *est) } static -struct gen_estimator *gen_find_node(const struct gnet_stats_basic *bstats, +struct gen_estimator *gen_find_node(const struct gnet_stats_basic_packed *bstats, const struct gnet_stats_rate_est *rate_est) { struct rb_node *p = est_root.rb_node; @@ -202,7 +202,7 @@ struct gen_estimator *gen_find_node(const struct gnet_stats_basic *bstats, * * NOTE: Called under rtnl_mutex */ -int gen_new_estimator(struct gnet_stats_basic *bstats, +int gen_new_estimator(struct gnet_stats_basic_packed *bstats, struct gnet_stats_rate_est *rate_est, spinlock_t *stats_lock, struct nlattr *opt) @@ -262,7 +262,7 @@ static void __gen_kill_estimator(struct rcu_head *head) * * NOTE: Called under rtnl_mutex */ -void gen_kill_estimator(struct gnet_stats_basic *bstats, +void gen_kill_estimator(struct gnet_stats_basic_packed *bstats, struct gnet_stats_rate_est *rate_est) { struct gen_estimator *e; @@ -292,7 +292,7 @@ EXPORT_SYMBOL(gen_kill_estimator); * * Returns 0 on success or a negative error code. */ -int gen_replace_estimator(struct gnet_stats_basic *bstats, +int gen_replace_estimator(struct gnet_stats_basic_packed *bstats, struct gnet_stats_rate_est *rate_est, spinlock_t *stats_lock, struct nlattr *opt) { @@ -308,7 +308,7 @@ EXPORT_SYMBOL(gen_replace_estimator); * * Returns true if estimator is active, and false if not. */ -bool gen_estimator_active(const struct gnet_stats_basic *bstats, +bool gen_estimator_active(const struct gnet_stats_basic_packed *bstats, const struct gnet_stats_rate_est *rate_est) { ASSERT_RTNL(); diff --git a/net/core/gen_stats.c b/net/core/gen_stats.c index c3d0ffeac24..8569310268a 100644 --- a/net/core/gen_stats.c +++ b/net/core/gen_stats.c @@ -106,16 +106,21 @@ gnet_stats_start_copy(struct sk_buff *skb, int type, spinlock_t *lock, * if the room in the socket buffer was not sufficient. */ int -gnet_stats_copy_basic(struct gnet_dump *d, struct gnet_stats_basic *b) +gnet_stats_copy_basic(struct gnet_dump *d, struct gnet_stats_basic_packed *b) { if (d->compat_tc_stats) { d->tc_stats.bytes = b->bytes; d->tc_stats.packets = b->packets; } - if (d->tail) - return gnet_stats_copy(d, TCA_STATS_BASIC, b, sizeof(*b)); + if (d->tail) { + struct gnet_stats_basic sb; + memset(&sb, 0, sizeof(sb)); + sb.bytes = b->bytes; + sb.packets = b->packets; + return gnet_stats_copy(d, TCA_STATS_BASIC, &sb, sizeof(sb)); + } return 0; } diff --git a/net/netfilter/xt_RATEEST.c b/net/netfilter/xt_RATEEST.c index 43f5676b1af..d80b8192e0d 100644 --- a/net/netfilter/xt_RATEEST.c +++ b/net/netfilter/xt_RATEEST.c @@ -74,7 +74,7 @@ static unsigned int xt_rateest_tg(struct sk_buff *skb, const struct xt_target_param *par) { const struct xt_rateest_target_info *info = par->targinfo; - struct gnet_stats_basic *stats = &info->est->bstats; + struct gnet_stats_basic_packed *stats = &info->est->bstats; spin_lock_bh(&info->est->lock); stats->bytes += skb->len; diff --git a/net/sched/sch_atm.c b/net/sched/sch_atm.c index 2a8b83af7c4..ab82f145f68 100644 --- a/net/sched/sch_atm.c +++ b/net/sched/sch_atm.c @@ -49,7 +49,7 @@ struct atm_flow_data { struct socket *sock; /* for closing */ u32 classid; /* x:y type ID */ int ref; /* reference count */ - struct gnet_stats_basic bstats; + struct gnet_stats_basic_packed bstats; struct gnet_stats_queue qstats; struct atm_flow_data *next; struct atm_flow_data *excess; /* flow for excess traffic; diff --git a/net/sched/sch_cbq.c b/net/sched/sch_cbq.c index 23a167670fd..d5798e17a83 100644 --- a/net/sched/sch_cbq.c +++ b/net/sched/sch_cbq.c @@ -128,7 +128,7 @@ struct cbq_class long avgidle; long deficit; /* Saved deficit for WRR */ psched_time_t penalized; - struct gnet_stats_basic bstats; + struct gnet_stats_basic_packed bstats; struct gnet_stats_queue qstats; struct gnet_stats_rate_est rate_est; struct tc_cbq_xstats xstats; diff --git a/net/sched/sch_drr.c b/net/sched/sch_drr.c index 7597fe14686..12b2fb04b29 100644 --- a/net/sched/sch_drr.c +++ b/net/sched/sch_drr.c @@ -22,7 +22,7 @@ struct drr_class { unsigned int refcnt; unsigned int filter_cnt; - struct gnet_stats_basic bstats; + struct gnet_stats_basic_packed bstats; struct gnet_stats_queue qstats; struct gnet_stats_rate_est rate_est; struct list_head alist; diff --git a/net/sched/sch_hfsc.c b/net/sched/sch_hfsc.c index 362c2811b2d..dad0144423d 100644 --- a/net/sched/sch_hfsc.c +++ b/net/sched/sch_hfsc.c @@ -116,7 +116,7 @@ struct hfsc_class struct Qdisc_class_common cl_common; unsigned int refcnt; /* usage count */ - struct gnet_stats_basic bstats; + struct gnet_stats_basic_packed bstats; struct gnet_stats_queue qstats; struct gnet_stats_rate_est rate_est; unsigned int level; /* class level in hierarchy */ diff --git a/net/sched/sch_htb.c b/net/sched/sch_htb.c index 88cd0262662..ec4d46399d5 100644 --- a/net/sched/sch_htb.c +++ b/net/sched/sch_htb.c @@ -74,7 +74,7 @@ enum htb_cmode { struct htb_class { struct Qdisc_class_common common; /* general class parameters */ - struct gnet_stats_basic bstats; + struct gnet_stats_basic_packed bstats; struct gnet_stats_queue qstats; struct gnet_stats_rate_est rate_est; struct tc_htb_xstats xstats; /* our special stats */ -- GitLab From 1154ecbd2f8298ef75609f5f8ed5aca96be599fb Mon Sep 17 00:00:00 2001 From: Zhang Qiang Date: Tue, 18 Aug 2009 14:58:24 +0800 Subject: [PATCH 1204/1342] nilfs2: missing a read lock for segment writer in nilfs_attach_checkpoint() 'ns_cno' of structure 'the_nilfs' must be protected from segment writer, in other words, the caller of nilfs_get_checkpoint should hold read lock for nilfs->ns_segctor_sem. This patch adds the lock/unlock operations in nilfs_attach_checkpoint() when calling nilfs_cpfile_get_checkpoint(). Signed-off-by: Zhang Qiang Signed-off-by: Ryusuke Konishi --- fs/nilfs2/super.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/fs/nilfs2/super.c b/fs/nilfs2/super.c index 8e2ec43b18f..151964f0de4 100644 --- a/fs/nilfs2/super.c +++ b/fs/nilfs2/super.c @@ -416,8 +416,10 @@ int nilfs_attach_checkpoint(struct nilfs_sb_info *sbi, __u64 cno) if (unlikely(err)) goto failed; + down_read(&nilfs->ns_segctor_sem); err = nilfs_cpfile_get_checkpoint(nilfs->ns_cpfile, cno, 0, &raw_cp, &bh_cp); + up_read(&nilfs->ns_segctor_sem); if (unlikely(err)) { if (err == -ENOENT || err == -EINVAL) { printk(KERN_ERR -- GitLab From 6b99ecec25c8fd501e74306f5d23dd0365065e2a Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Thu, 6 Aug 2009 23:00:38 +0200 Subject: [PATCH 1205/1342] microblaze: use the generic ack_bad_irq implementation Signed-off-by: Christoph Hellwig Signed-off-by: Michal Simek --- arch/microblaze/include/asm/hardirq.h | 2 -- arch/microblaze/kernel/irq.c | 9 --------- 2 files changed, 11 deletions(-) diff --git a/arch/microblaze/include/asm/hardirq.h b/arch/microblaze/include/asm/hardirq.h index 41e1e1aa36a..cd1ac9aad56 100644 --- a/arch/microblaze/include/asm/hardirq.h +++ b/arch/microblaze/include/asm/hardirq.h @@ -12,8 +12,6 @@ /* should be defined in each interrupt controller driver */ extern unsigned int get_irq(struct pt_regs *regs); -#define ack_bad_irq ack_bad_irq -void ack_bad_irq(unsigned int irq); #include #endif /* _ASM_MICROBLAZE_HARDIRQ_H */ diff --git a/arch/microblaze/kernel/irq.c b/arch/microblaze/kernel/irq.c index f688ee93e3b..7d5ddd62d4d 100644 --- a/arch/microblaze/kernel/irq.c +++ b/arch/microblaze/kernel/irq.c @@ -30,15 +30,6 @@ unsigned int irq_of_parse_and_map(struct device_node *dev, int index) } EXPORT_SYMBOL_GPL(irq_of_parse_and_map); -/* - * 'what should we do if we get a hw irq event on an illegal vector'. - * each architecture has to answer this themselves. - */ -void ack_bad_irq(unsigned int irq) -{ - printk(KERN_WARNING "unexpected IRQ trap at vector %02x\n", irq); -} - static u32 concurrent_irq; void do_IRQ(struct pt_regs *regs) -- GitLab From 892ee92b81b6e7fa5f6147c96e11c6c1b9802fc6 Mon Sep 17 00:00:00 2001 From: John Williams Date: Wed, 29 Jul 2009 22:08:40 +1000 Subject: [PATCH 1206/1342] microblaze: Sane handling of missing timer/intc in device tree This code path doesn't test any returned pointers for NULL, leading to a bad kernel page fault if there's no timer/intc found. Slightly better is to BUG(), but even better still would be a printk beforehand. Signed-off-by: John Williams Signed-off-by: Michal Simek --- arch/microblaze/kernel/intc.c | 2 ++ arch/microblaze/kernel/timer.c | 2 ++ 2 files changed, 4 insertions(+) diff --git a/arch/microblaze/kernel/intc.c b/arch/microblaze/kernel/intc.c index b15605299a5..6eea6f92b84 100644 --- a/arch/microblaze/kernel/intc.c +++ b/arch/microblaze/kernel/intc.c @@ -12,6 +12,7 @@ #include #include #include +#include #include #include @@ -130,6 +131,7 @@ void __init init_IRQ(void) if (intc) break; } + BUG_ON(!intc); intc_baseaddr = *(int *) of_get_property(intc, "reg", NULL); intc_baseaddr = (unsigned long) ioremap(intc_baseaddr, PAGE_SIZE); diff --git a/arch/microblaze/kernel/timer.c b/arch/microblaze/kernel/timer.c index bdfa2f9f0c8..5499deae7fa 100644 --- a/arch/microblaze/kernel/timer.c +++ b/arch/microblaze/kernel/timer.c @@ -22,6 +22,7 @@ #include #include #include +#include #include #include #include @@ -234,6 +235,7 @@ void __init time_init(void) if (timer) break; } + BUG_ON(!timer); timer_baseaddr = *(int *) of_get_property(timer, "reg", NULL); timer_baseaddr = (unsigned long) ioremap(timer_baseaddr, PAGE_SIZE); -- GitLab From 2856ed35ead295a7cc8788d9ba860e746dfc92bb Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 6 Aug 2009 16:00:52 +0200 Subject: [PATCH 1207/1342] microblaze: Enable ppoll syscall Signed-off-by: Michal Simek --- arch/microblaze/kernel/syscall_table.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/microblaze/kernel/syscall_table.S b/arch/microblaze/kernel/syscall_table.S index 216db817beb..457216097df 100644 --- a/arch/microblaze/kernel/syscall_table.S +++ b/arch/microblaze/kernel/syscall_table.S @@ -313,7 +313,7 @@ ENTRY(sys_call_table) .long sys_fchmodat .long sys_faccessat .long sys_ni_syscall /* pselect6 */ - .long sys_ni_syscall /* sys_ppoll */ + .long sys_ppoll .long sys_unshare /* 310 */ .long sys_set_robust_list .long sys_get_robust_list -- GitLab From 8f37b6c9852ff79cc8472c44ea6f6485dfd58bd2 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Tue, 11 Aug 2009 12:36:12 +0200 Subject: [PATCH 1208/1342] microblaze: Use klimit instead of _end for memory init For noMMU system when you use larger rootfs image there is problem with using _end label because we increase klimit but in memory initialization we use still _end which is wrong. Larger mtd rootfs was rewritten by init_bootmem_node. MMU kernel use static initialization where klimit is setup to _end. There is no any other hanling with klimit. Signed-off-by: Michal Simek --- arch/microblaze/mm/init.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/microblaze/mm/init.c b/arch/microblaze/mm/init.c index 8d92c4efe9a..f207f1a94db 100644 --- a/arch/microblaze/mm/init.c +++ b/arch/microblaze/mm/init.c @@ -130,13 +130,13 @@ void __init setup_memory(void) * (in case the address isn't page-aligned). */ #ifndef CONFIG_MMU - map_size = init_bootmem_node(NODE_DATA(0), PFN_UP(TOPHYS((u32)_end)), + map_size = init_bootmem_node(NODE_DATA(0), PFN_UP(TOPHYS((u32)klimit)), min_low_pfn, max_low_pfn); #else map_size = init_bootmem_node(&contig_page_data, - PFN_UP(TOPHYS((u32)_end)), min_low_pfn, max_low_pfn); + PFN_UP(TOPHYS((u32)klimit)), min_low_pfn, max_low_pfn); #endif - lmb_reserve(PFN_UP(TOPHYS((u32)_end)) << PAGE_SHIFT, map_size); + lmb_reserve(PFN_UP(TOPHYS((u32)klimit)) << PAGE_SHIFT, map_size); /* free bootmem is whole main memory */ free_bootmem(memory_start, memory_size); -- GitLab From 1fef7891755d99039592aa8d1ed02e981f38de15 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Tue, 18 Aug 2009 11:05:11 +0200 Subject: [PATCH 1209/1342] microblaze: Update Microblaze defconfigs Signed-off-by: Michal Simek --- arch/microblaze/configs/mmu_defconfig | 70 ++++++++++--------- arch/microblaze/configs/nommu_defconfig | 91 +++++++++++++++---------- 2 files changed, 91 insertions(+), 70 deletions(-) diff --git a/arch/microblaze/configs/mmu_defconfig b/arch/microblaze/configs/mmu_defconfig index bd0b85ec38f..09c32962b66 100644 --- a/arch/microblaze/configs/mmu_defconfig +++ b/arch/microblaze/configs/mmu_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc6 -# Fri May 22 10:02:33 2009 +# Linux kernel version: 2.6.31-rc6 +# Tue Aug 18 11:00:02 2009 # CONFIG_MICROBLAZE=y # CONFIG_SWAP is not set @@ -18,7 +18,11 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_CSUM=y +# CONFIG_PCI is not set +CONFIG_NO_DMA=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -59,8 +63,8 @@ CONFIG_INITRAMFS_ROOT_GID=0 CONFIG_RD_GZIP=y # CONFIG_RD_BZIP2 is not set # CONFIG_RD_LZMA is not set -CONFIG_INITRAMFS_COMPRESSION_NONE=y -# CONFIG_INITRAMFS_COMPRESSION_GZIP is not set +# CONFIG_INITRAMFS_COMPRESSION_NONE is not set +CONFIG_INITRAMFS_COMPRESSION_GZIP=y # CONFIG_INITRAMFS_COMPRESSION_BZIP2 is not set # CONFIG_INITRAMFS_COMPRESSION_LZMA is not set # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set @@ -71,7 +75,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_ALL=y CONFIG_KALLSYMS_EXTRA_PASS=y -# CONFIG_STRIP_ASM_SYMS is not set # CONFIG_HOTPLUG is not set CONFIG_PRINTK=y CONFIG_BUG=y @@ -84,13 +87,22 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y # CONFIG_SHMEM is not set CONFIG_AIO=y + +# +# Performance Counters +# CONFIG_VM_EVENT_COUNTERS=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -102,7 +114,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -194,9 +206,9 @@ CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 # # Exectuable file formats @@ -262,6 +274,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -325,7 +338,6 @@ CONFIG_MISC_DEVICES=y # CONFIG_ATA is not set # CONFIG_MD is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -344,7 +356,7 @@ CONFIG_NET_ETHERNET=y # CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set -# CONFIG_B44 is not set +# CONFIG_KS8842 is not set CONFIG_NETDEV_1000=y CONFIG_NETDEV_10000=y @@ -410,6 +422,11 @@ CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_TCG_TPM is not set # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -418,12 +435,6 @@ CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set -CONFIG_SSB_POSSIBLE=y - -# -# Sonics Silicon Backplane -# -# CONFIG_SSB is not set # # Multifunction device drivers @@ -433,22 +444,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -# CONFIG_DAB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -469,9 +465,12 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_NEW_LEDS is not set # CONFIG_ACCESSIBILITY is not set # CONFIG_RTC_CLASS is not set -# CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -485,12 +484,15 @@ CONFIG_EXT2_FS=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y # CONFIG_DNOTIFY is not set # CONFIG_INOTIFY is not set +CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set @@ -678,6 +680,7 @@ CONFIG_DEBUG_INFO=y # CONFIG_SYSCTL_SYSCALL_CHECK is not set # CONFIG_PAGE_POISONING is not set # CONFIG_SAMPLES is not set +# CONFIG_KMEMCHECK is not set CONFIG_EARLY_PRINTK=y CONFIG_HEART_BEAT=y CONFIG_DEBUG_BOOTMEM=y @@ -793,6 +796,5 @@ CONFIG_ZLIB_INFLATE=y CONFIG_DECOMPRESS_GZIP=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y -CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y diff --git a/arch/microblaze/configs/nommu_defconfig b/arch/microblaze/configs/nommu_defconfig index 4ef6af0a8f3..8b638615a97 100644 --- a/arch/microblaze/configs/nommu_defconfig +++ b/arch/microblaze/configs/nommu_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc5 -# Mon May 11 09:01:02 2009 +# Linux kernel version: 2.6.31-rc6 +# Tue Aug 18 10:35:30 2009 # CONFIG_MICROBLAZE=y # CONFIG_SWAP is not set @@ -17,9 +17,12 @@ CONFIG_GENERIC_TIME=y # CONFIG_GENERIC_TIME_VSYSCALL is not set CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_CSUM=y # CONFIG_PCI is not set -# CONFIG_NO_DMA is not set +CONFIG_NO_DMA=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -64,7 +67,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_ALL=y CONFIG_KALLSYMS_EXTRA_PASS=y -# CONFIG_STRIP_ASM_SYMS is not set # CONFIG_HOTPLUG is not set CONFIG_PRINTK=y CONFIG_BUG=y @@ -76,13 +78,23 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_AIO=y + +# +# Performance Counters +# CONFIG_VM_EVENT_COUNTERS=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set + +# +# GCOV-based kernel profiling +# +# CONFIG_GCOV_KERNEL is not set # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -95,7 +107,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -156,8 +168,16 @@ CONFIG_CMDLINE_BOOL=y CONFIG_CMDLINE="console=ttyUL0,115200" # CONFIG_CMDLINE_FORCE is not set CONFIG_OF=y -CONFIG_OF_DEVICE=y CONFIG_PROC_DEVICETREE=y + +# +# Advanced setup +# + +# +# Default settings for advanced configuration options are used +# +CONFIG_KERNEL_START=0x90000000 CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y # CONFIG_DISCONTIGMEM_MANUAL is not set @@ -169,7 +189,7 @@ CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_NOMMU_INITIAL_TRIM_EXCESS=1 # @@ -237,6 +257,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -254,7 +275,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -353,6 +378,7 @@ CONFIG_MTD_UCLINUX=y # UBI - Unsorted block images # # CONFIG_MTD_UBI is not set +CONFIG_OF_DEVICE=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_COW_COMMON is not set @@ -364,6 +390,7 @@ CONFIG_BLK_DEV_RAM_SIZE=4096 # CONFIG_BLK_DEV_XIP is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set +# CONFIG_XILINX_SYSACE is not set CONFIG_MISC_DEVICES=y # CONFIG_ENCLOSURE_SERVICES is not set # CONFIG_C2PORT is not set @@ -383,7 +410,6 @@ CONFIG_MISC_DEVICES=y # CONFIG_ATA is not set # CONFIG_MD is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -402,7 +428,7 @@ CONFIG_NET_ETHERNET=y # CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set -# CONFIG_B44 is not set +# CONFIG_KS8842 is not set CONFIG_NETDEV_1000=y CONFIG_NETDEV_10000=y @@ -463,23 +489,25 @@ CONFIG_HW_RANDOM=y # CONFIG_HW_RANDOM_TIMERIOMEM is not set # CONFIG_RTC is not set # CONFIG_GEN_RTC is not set +# CONFIG_XILINX_HWICAP is not set # CONFIG_R3964 is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set +CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y +# CONFIG_GPIOLIB is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set -CONFIG_SSB_POSSIBLE=y - -# -# Sonics Silicon Backplane -# -# CONFIG_SSB is not set # # Multifunction device drivers @@ -489,22 +517,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -CONFIG_DAB=y +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -520,9 +533,10 @@ CONFIG_VIDEO_OUTPUT_CONTROL=y # CONFIG_DISPLAY_SUPPORT is not set # CONFIG_SOUND is not set CONFIG_USB_SUPPORT=y -# CONFIG_USB_ARCH_HAS_HCD is not set +CONFIG_USB_ARCH_HAS_HCD=y # CONFIG_USB_ARCH_HAS_OHCI is not set # CONFIG_USB_ARCH_HAS_EHCI is not set +# CONFIG_USB is not set # CONFIG_USB_OTG_WHITELIST is not set # CONFIG_USB_OTG_BLACKLIST_HUB is not set @@ -543,9 +557,12 @@ CONFIG_USB_SUPPORT=y # CONFIG_NEW_LEDS is not set # CONFIG_ACCESSIBILITY is not set # CONFIG_RTC_CLASS is not set -# CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -558,12 +575,15 @@ CONFIG_EXT2_FS=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y # CONFIG_DNOTIFY is not set # CONFIG_INOTIFY is not set +CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set @@ -813,6 +833,5 @@ CONFIG_GENERIC_FIND_LAST_BIT=y CONFIG_ZLIB_INFLATE=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y -CONFIG_HAS_DMA=y CONFIG_HAVE_LMB=y CONFIG_NLATTR=y -- GitLab From f738eb1b63edf664da1b4ac76895d988749b2f07 Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Tue, 18 Aug 2009 11:32:24 +0200 Subject: [PATCH 1210/1342] perf_counter: Fix the PARISC build PARISC does not build: /home/mingo/tip/kernel/perf_counter.c: In function 'perf_counter_index': /home/mingo/tip/kernel/perf_counter.c:2016: error: 'PERF_COUNTER_INDEX_OFFSET' undeclared (first use in this function) /home/mingo/tip/kernel/perf_counter.c:2016: error: (Each undeclared identifier is reported only once /home/mingo/tip/kernel/perf_counter.c:2016: error: for each function it appears in.) As PERF_COUNTER_INDEX_OFFSET is not defined. Now, we could define it in the architecture - but lets also provide a core default of 0 (which happens to be what all but one architecture uses at the moment). Architectures that need a different index offset should set this value in their asm/perf_counter.h files. Cc: Kyle McMartin Cc: Helge Deller Cc: linux-parisc@vger.kernel.org Cc: Peter Zijlstra Cc: Mike Galbraith Cc: Paul Mackerras Cc: Arnaldo Carvalho de Melo Cc: Frederic Weisbecker LKML-Reference: Signed-off-by: Ingo Molnar --- kernel/perf_counter.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index b8fe7397b90..36f65e2b8b5 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -2019,6 +2019,10 @@ int perf_counter_task_disable(void) return 0; } +#ifndef PERF_COUNTER_INDEX_OFFSET +# define PERF_COUNTER_INDEX_OFFSET 0 +#endif + static int perf_counter_index(struct perf_counter *counter) { if (counter->state != PERF_COUNTER_STATE_ACTIVE) -- GitLab From 15f3fa4e7f608c5ce19187b3b4a953222fdfa751 Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Tue, 18 Aug 2009 13:52:28 +0200 Subject: [PATCH 1211/1342] perf annotate: Fix segmentation fault Linus reported this perf annotate segfault: [torvalds@nehalem git]$ perf annotate unmap_vmas Segmentation fault #0 map__clone (self=) at builtin-annotate.c:236 #1 thread__fork (self=) at builtin-annotate.c:372 The bug here was that builtin-annotate.c was a copy of builtin-report.c and a threading related fix to builtin-report.c didnt get propagated to builtin-annotate.c ... Reported-by: Linus Torvalds Cc: Peter Zijlstra Cc: Mike Galbraith Cc: Paul Mackerras Cc: Arnaldo Carvalho de Melo Cc: Frederic Weisbecker LKML-Reference: Signed-off-by: Ingo Molnar --- tools/perf/builtin-annotate.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/tools/perf/builtin-annotate.c b/tools/perf/builtin-annotate.c index 1dba568e194..343e7b14bf0 100644 --- a/tools/perf/builtin-annotate.c +++ b/tools/perf/builtin-annotate.c @@ -980,6 +980,13 @@ process_fork_event(event_t *event, unsigned long offset, unsigned long head) (void *)(long)(event->header.size), event->fork.pid, event->fork.ppid); + /* + * A thread clone will have the same PID for both + * parent and child. + */ + if (thread == parent) + return 0; + if (!thread || !parent || thread__fork(thread, parent)) { dprintf("problem processing PERF_EVENT_FORK, skipping event.\n"); return -1; -- GitLab From 69ab849439b506cd8dd2879527fdb64d95dd5211 Mon Sep 17 00:00:00 2001 From: Thomas Gleixner Date: Mon, 17 Aug 2009 14:07:16 +0200 Subject: [PATCH 1212/1342] genirq: Wake up irq thread after action has been installed The wake_up_process() of the new irq thread in __setup_irq() is too early as the irqaction is not yet fully initialized especially action->irq is not yet set. The interrupt thread might dereference the wrong irq descriptor. Move the wakeup after the action is installed and action->irq has been set. Reported-by: Michael Buesch Signed-off-by: Thomas Gleixner Tested-by: Michael Buesch --- kernel/irq/manage.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) diff --git a/kernel/irq/manage.c b/kernel/irq/manage.c index d222515a5a0..0ec9ed83173 100644 --- a/kernel/irq/manage.c +++ b/kernel/irq/manage.c @@ -607,7 +607,6 @@ __setup_irq(unsigned int irq, struct irq_desc *desc, struct irqaction *new) */ get_task_struct(t); new->thread = t; - wake_up_process(t); } /* @@ -690,6 +689,7 @@ __setup_irq(unsigned int irq, struct irq_desc *desc, struct irqaction *new) (int)(new->flags & IRQF_TRIGGER_MASK)); } + new->irq = irq; *old_ptr = new; /* Reset broken irq detection when installing new handler */ @@ -707,7 +707,13 @@ __setup_irq(unsigned int irq, struct irq_desc *desc, struct irqaction *new) spin_unlock_irqrestore(&desc->lock, flags); - new->irq = irq; + /* + * Strictly no need to wake it up, but hung_task complains + * when no hard interrupt wakes the thread up. + */ + if (new->thread) + wake_up_process(new->thread); + register_irq_proc(irq, desc); new->dir = NULL; register_handler_proc(irq, new); -- GitLab From 78b89ecd731798f2fec8cc26ca90739253cec33c Mon Sep 17 00:00:00 2001 From: Jan Beulich Date: Tue, 18 Aug 2009 16:41:33 +0100 Subject: [PATCH 1213/1342] i386: Fix section mismatches for init code with !HOTPLUG_CPU Commit 0e83815be719d3391bf5ea24b7fe696c07dbd417 changed the section the initial_code variable gets allocated in, in an attempt to address a section conflict warning. This, however created a new section conflict when building without HOTPLUG_CPU. The apparently only (reasonable) way to address this is to always use __REFDATA. Once at it, also fix a second section mismatch when not using HOTPLUG_CPU. Signed-off-by: Jan Beulich Cc: Robert Richter LKML-Reference: <4A8AE7CD020000780001054B@vpn.id2.novell.com> Signed-off-by: Ingo Molnar --- arch/x86/kernel/head_32.S | 8 +------- 1 file changed, 1 insertion(+), 7 deletions(-) diff --git a/arch/x86/kernel/head_32.S b/arch/x86/kernel/head_32.S index 0d98a01cbdb..cc827ac9e8d 100644 --- a/arch/x86/kernel/head_32.S +++ b/arch/x86/kernel/head_32.S @@ -261,9 +261,7 @@ page_pde_offset = (__PAGE_OFFSET >> 20); * which will be freed later */ -#ifndef CONFIG_HOTPLUG_CPU -.section .init.text,"ax",@progbits -#endif +__CPUINIT #ifdef CONFIG_SMP ENTRY(startup_32_smp) @@ -602,11 +600,7 @@ ignore_int: #endif iret -#ifndef CONFIG_HOTPLUG_CPU - __CPUINITDATA -#else __REFDATA -#endif .align 4 ENTRY(initial_code) .long i386_start_kernel -- GitLab From b395cd8a74b4a8d943dd4b5585e676f62f7350b3 Mon Sep 17 00:00:00 2001 From: Kyle McMartin Date: Tue, 18 Aug 2009 12:41:25 -0400 Subject: [PATCH 1214/1342] perf tools: Make 'make html' work pushd tools/perf/Documentation make html popd is failing for me... ASCIIDOC perf-annotate.html ERROR: unsafe: include file: /etc/asciidoc/./stylesheets/xhtml11.css ERROR: unsafe: include file: /etc/asciidoc/./stylesheets/xhtml11-manpage.css ERROR: unsafe: include file: /etc/asciidoc/./stylesheets/xhtml11-quirks.css make: *** [perf-annotate.html] Error 1 Apparently asciidoc "unsafe" is the default mode of operation in practice. https://bugzilla.redhat.com/show_bug.cgi?id=506953 Works tidily now. Signed-off-by: Kyle McMartin Cc: Peter Zijlstra Cc: Mike Galbraith Cc: Paul Mackerras Cc: Arnaldo Carvalho de Melo Cc: Frederic Weisbecker LKML-Reference: <20090818164125.GM25206@bombadil.infradead.org> Signed-off-by: Ingo Molnar --- tools/perf/Documentation/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/tools/perf/Documentation/Makefile b/tools/perf/Documentation/Makefile index 5457192e1b4..bdd3b7ecad0 100644 --- a/tools/perf/Documentation/Makefile +++ b/tools/perf/Documentation/Makefile @@ -35,7 +35,7 @@ man7dir=$(mandir)/man7 # DESTDIR= ASCIIDOC=asciidoc -ASCIIDOC_EXTRA = +ASCIIDOC_EXTRA = --unsafe MANPAGE_XSL = manpage-normal.xsl XMLTO_EXTRA = INSTALL?=install -- GitLab From a924586036833086b262a371b09d1266c23bb4d1 Mon Sep 17 00:00:00 2001 From: Ryusuke Konishi Date: Wed, 19 Aug 2009 00:29:43 +0900 Subject: [PATCH 1215/1342] nilfs2: fix oopses with doubly mounted snapshots will fix kernel oopses like the following: # mount -t nilfs2 -r -o cp=20 /dev/sdb1 /test1 # mount -t nilfs2 -r -o cp=20 /dev/sdb1 /test2 # umount /test1 # umount /test2 BUG: sleeping function called from invalid context at arch/x86/mm/fault.c:1069 in_atomic(): 0, irqs_disabled(): 1, pid: 3886, name: umount.nilfs2 1 lock held by umount.nilfs2/3886: #0: (&type->s_umount_key#31){+.+...}, at: [] deactivate_super+0x52/0x6c irq event stamp: 1219 hardirqs last enabled at (1219): [] __mutex_unlock_slowpath+0xf8/0x119 hardirqs last disabled at (1218): [] __mutex_unlock_slowpath+0x59/0x119 softirqs last enabled at (1214): [] __do_softirq+0x1a5/0x1ad softirqs last disabled at (1205): [] do_softirq+0x36/0x5a Pid: 3886, comm: umount.nilfs2 Not tainted 2.6.31-rc6 #55 Call Trace: [] __might_sleep+0x107/0x10e [] do_page_fault+0x246/0x397 [] ? do_page_fault+0x0/0x397 [] error_code+0x6b/0x70 [] ? do_page_fault+0x0/0x397 [] ? __lock_acquire+0x91/0x12fd [] ? __lock_acquire+0x12ee/0x12fd [] ? __lock_acquire+0x12ee/0x12fd [] lock_acquire+0xba/0xdd [] ? nilfs_detach_segment_constructor+0x2f/0x2fa [nilfs2] [] down_write+0x2a/0x46 [] ? nilfs_detach_segment_constructor+0x2f/0x2fa [nilfs2] [] nilfs_detach_segment_constructor+0x2f/0x2fa [nilfs2] [] ? mark_held_locks+0x43/0x5b [] ? trace_hardirqs_on_caller+0x10b/0x133 [] ? trace_hardirqs_on+0xb/0xd [] nilfs_put_super+0x2f/0xca [nilfs2] [] generic_shutdown_super+0x49/0xb8 [] kill_block_super+0x1d/0x31 [] ? vfs_quota_off+0x0/0x12 [] deactivate_super+0x57/0x6c [] mntput_no_expire+0x8c/0xb4 [] sys_umount+0x27f/0x2a4 [] sys_oldumount+0xd/0xf [] sysenter_do_call+0x12/0x38 ... This turns out to be a bug brought by an -rc1 patch ("nilfs2: simplify remaining sget() use"). In the patch, a new "put resource" function, nilfs_put_sbinfo() was introduced to delay freeing nilfs_sb_info struct. But the nilfs_put_sbinfo() mistakenly used atomic_dec_and_test() function to check the reference count, and it caused the nilfs_sb_info was freed when user mounted a snapshot twice. This bug also suggests there was unseen memory leak in usual mount /umount operations for nilfs. Signed-off-by: Ryusuke Konishi --- fs/nilfs2/the_nilfs.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/nilfs2/the_nilfs.h b/fs/nilfs2/the_nilfs.h index e8adbffc626..1b9caafb866 100644 --- a/fs/nilfs2/the_nilfs.h +++ b/fs/nilfs2/the_nilfs.h @@ -253,7 +253,7 @@ nilfs_detach_writer(struct the_nilfs *nilfs, struct nilfs_sb_info *sbi) static inline void nilfs_put_sbinfo(struct nilfs_sb_info *sbi) { - if (!atomic_dec_and_test(&sbi->s_count)) + if (atomic_dec_and_test(&sbi->s_count)) kfree(sbi); } -- GitLab From a58578e47f004017cf47803ad372490806630e58 Mon Sep 17 00:00:00 2001 From: Dave Jones Date: Tue, 18 Aug 2009 13:47:37 -0400 Subject: [PATCH 1216/1342] security: Make LSM_MMAP_MIN_ADDR default match its help text. Commit 788084aba2ab7348257597496befcbccabdc98a3 added the LSM_MMAP_MIN_ADDR option, whose help text states "For most ia64, ppc64 and x86 users with lots of address space a value of 65536 is reasonable and should cause no problems." Which implies that it's default setting was typoed. Signed-off-by: Dave Jones Acked-by: Eric Paris Signed-off-by: James Morris --- security/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/security/Kconfig b/security/Kconfig index 9c60c346a91..bba92689b56 100644 --- a/security/Kconfig +++ b/security/Kconfig @@ -116,7 +116,7 @@ config SECURITY_ROOTPLUG config LSM_MMAP_MIN_ADDR int "Low address space for LSM to from user allocation" depends on SECURITY && SECURITY_SELINUX - default 65535 + default 65536 help This is the portion of low virtual memory which should be protected from userspace allocation. Keeping a user from writing to low pages -- GitLab From 024e6cb408307de41cbfcb1e5a170d9af60ab2a9 Mon Sep 17 00:00:00 2001 From: Andreas Schwab Date: Tue, 18 Aug 2009 22:14:29 +0200 Subject: [PATCH 1217/1342] security: Fix prompt for LSM_MMAP_MIN_ADDR Fix prompt for LSM_MMAP_MIN_ADDR. (Verbs are cool!) Signed-off-by: Andreas Schwab Acked-by: Eric Paris Signed-off-by: James Morris --- security/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/security/Kconfig b/security/Kconfig index bba92689b56..4c865345caa 100644 --- a/security/Kconfig +++ b/security/Kconfig @@ -114,7 +114,7 @@ config SECURITY_ROOTPLUG If you are unsure how to answer this question, answer N. config LSM_MMAP_MIN_ADDR - int "Low address space for LSM to from user allocation" + int "Low address space for LSM to protect from user allocation" depends on SECURITY && SECURITY_SELINUX default 65536 help -- GitLab From 6b6f0b6c131321e1bc34c47b7f671b0360315402 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 18 Aug 2009 14:11:06 -0700 Subject: [PATCH 1218/1342] MAINTAINERS: OSD LIBRARY and FILESYSTEM pattern fix Signed-off-by: Joe Perches Acked-by: Benny Halevy Cc: Boaz Harrosh Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/MAINTAINERS b/MAINTAINERS index 557d4dcc2c2..ac0fdfd2e50 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -3809,7 +3809,7 @@ W: http://open-osd.org T: git git://git.open-osd.org/open-osd.git S: Maintained F: drivers/scsi/osd/ -F: drivers/include/scsi/osd_* +F: include/scsi/osd_* F: fs/exofs/ P54 WIRELESS DRIVER -- GitLab From 89a4eb4b66e8f4d395e14a14d262dac4d6ca52f0 Mon Sep 17 00:00:00 2001 From: Jeff Layton Date: Tue, 18 Aug 2009 14:11:08 -0700 Subject: [PATCH 1219/1342] vfs: make get_sb_pseudo set s_maxbytes to value that can be cast to signed get_sb_pseudo sets s_maxbytes to ~0ULL which becomes negative when cast to a signed value. Fix it to use MAX_LFS_FILESIZE which casts properly to a positive signed value. Signed-off-by: Jeff Layton Reviewed-by: Johannes Weiner Acked-by: Steve French Reviewed-by: Christoph Hellwig Cc: Al Viro Cc: Robert Love Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- fs/libfs.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/libfs.c b/fs/libfs.c index ddfa89948c3..dcec3d3ea64 100644 --- a/fs/libfs.c +++ b/fs/libfs.c @@ -217,7 +217,7 @@ int get_sb_pseudo(struct file_system_type *fs_type, char *name, return PTR_ERR(s); s->s_flags = MS_NOUSER; - s->s_maxbytes = ~0ULL; + s->s_maxbytes = MAX_LFS_FILESIZE; s->s_blocksize = PAGE_SIZE; s->s_blocksize_bits = PAGE_SHIFT; s->s_magic = magic; -- GitLab From 0753ba01e126020bf0f8150934903b48935b697d Mon Sep 17 00:00:00 2001 From: KOSAKI Motohiro Date: Tue, 18 Aug 2009 14:11:10 -0700 Subject: [PATCH 1220/1342] mm: revert "oom: move oom_adj value" The commit 2ff05b2b (oom: move oom_adj value) moveed the oom_adj value to the mm_struct. It was a very good first step for sanitize OOM. However Paul Menage reported the commit makes regression to his job scheduler. Current OOM logic can kill OOM_DISABLED process. Why? His program has the code of similar to the following. ... set_oom_adj(OOM_DISABLE); /* The job scheduler never killed by oom */ ... if (vfork() == 0) { set_oom_adj(0); /* Invoked child can be killed */ execve("foo-bar-cmd"); } .... vfork() parent and child are shared the same mm_struct. then above set_oom_adj(0) doesn't only change oom_adj for vfork() child, it's also change oom_adj for vfork() parent. Then, vfork() parent (job scheduler) lost OOM immune and it was killed. Actually, fork-setting-exec idiom is very frequently used in userland program. We must not break this assumption. Then, this patch revert commit 2ff05b2b and related commit. Reverted commit list --------------------- - commit 2ff05b2b4e (oom: move oom_adj value from task_struct to mm_struct) - commit 4d8b9135c3 (oom: avoid unnecessary mm locking and scanning for OOM_DISABLE) - commit 8123681022 (oom: only oom kill exiting tasks with attached memory) - commit 933b787b57 (mm: copy over oom_adj value at fork time) Signed-off-by: KOSAKI Motohiro Cc: Paul Menage Cc: David Rientjes Cc: KAMEZAWA Hiroyuki Cc: Rik van Riel Cc: Linus Torvalds Cc: Oleg Nesterov Cc: Nick Piggin Cc: Mel Gorman Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/filesystems/proc.txt | 15 +++---- fs/proc/base.c | 19 ++------- include/linux/mm_types.h | 2 - include/linux/sched.h | 1 + kernel/fork.c | 1 - mm/oom_kill.c | 64 ++++++++++++++++++------------ 6 files changed, 48 insertions(+), 54 deletions(-) diff --git a/Documentation/filesystems/proc.txt b/Documentation/filesystems/proc.txt index fad18f9456e..ffead13f944 100644 --- a/Documentation/filesystems/proc.txt +++ b/Documentation/filesystems/proc.txt @@ -1167,13 +1167,11 @@ CHAPTER 3: PER-PROCESS PARAMETERS 3.1 /proc//oom_adj - Adjust the oom-killer score ------------------------------------------------------ -This file can be used to adjust the score used to select which processes should -be killed in an out-of-memory situation. The oom_adj value is a characteristic -of the task's mm, so all threads that share an mm with pid will have the same -oom_adj value. A high value will increase the likelihood of this process being -killed by the oom-killer. Valid values are in the range -16 to +15 as -explained below and a special value of -17, which disables oom-killing -altogether for threads sharing pid's mm. +This file can be used to adjust the score used to select which processes +should be killed in an out-of-memory situation. Giving it a high score will +increase the likelihood of this process being killed by the oom-killer. Valid +values are in the range -16 to +15, plus the special value -17, which disables +oom-killing altogether for this process. The process to be killed in an out-of-memory situation is selected among all others based on its badness score. This value equals the original memory size of the process @@ -1187,9 +1185,6 @@ the parent's score if they do not share the same memory. Thus forking servers are the prime candidates to be killed. Having only one 'hungry' child will make parent less preferable than the child. -/proc//oom_adj cannot be changed for kthreads since they are immune from -oom-killing already. - /proc//oom_score shows process' current badness score. The following heuristics are then applied: diff --git a/fs/proc/base.c b/fs/proc/base.c index 175db258942..6f742f6658a 100644 --- a/fs/proc/base.c +++ b/fs/proc/base.c @@ -1003,12 +1003,7 @@ static ssize_t oom_adjust_read(struct file *file, char __user *buf, if (!task) return -ESRCH; - task_lock(task); - if (task->mm) - oom_adjust = task->mm->oom_adj; - else - oom_adjust = OOM_DISABLE; - task_unlock(task); + oom_adjust = task->oomkilladj; put_task_struct(task); len = snprintf(buffer, sizeof(buffer), "%i\n", oom_adjust); @@ -1037,19 +1032,11 @@ static ssize_t oom_adjust_write(struct file *file, const char __user *buf, task = get_proc_task(file->f_path.dentry->d_inode); if (!task) return -ESRCH; - task_lock(task); - if (!task->mm) { - task_unlock(task); - put_task_struct(task); - return -EINVAL; - } - if (oom_adjust < task->mm->oom_adj && !capable(CAP_SYS_RESOURCE)) { - task_unlock(task); + if (oom_adjust < task->oomkilladj && !capable(CAP_SYS_RESOURCE)) { put_task_struct(task); return -EACCES; } - task->mm->oom_adj = oom_adjust; - task_unlock(task); + task->oomkilladj = oom_adjust; put_task_struct(task); if (end - buffer == 0) return -EIO; diff --git a/include/linux/mm_types.h b/include/linux/mm_types.h index 7acc8439d9b..0042090a4d7 100644 --- a/include/linux/mm_types.h +++ b/include/linux/mm_types.h @@ -240,8 +240,6 @@ struct mm_struct { unsigned long saved_auxv[AT_VECTOR_SIZE]; /* for /proc/PID/auxv */ - s8 oom_adj; /* OOM kill score adjustment (bit shift) */ - cpumask_t cpu_vm_mask; /* Architecture-specific MM context */ diff --git a/include/linux/sched.h b/include/linux/sched.h index 3ab08e4bb6b..0f1ea4a6695 100644 --- a/include/linux/sched.h +++ b/include/linux/sched.h @@ -1198,6 +1198,7 @@ struct task_struct { * a short time */ unsigned char fpu_counter; + s8 oomkilladj; /* OOM kill score adjustment (bit shift). */ #ifdef CONFIG_BLK_DEV_IO_TRACE unsigned int btrace_seq; #endif diff --git a/kernel/fork.c b/kernel/fork.c index 021e1138556..144326b7af5 100644 --- a/kernel/fork.c +++ b/kernel/fork.c @@ -426,7 +426,6 @@ static struct mm_struct * mm_init(struct mm_struct * mm, struct task_struct *p) init_rwsem(&mm->mmap_sem); INIT_LIST_HEAD(&mm->mmlist); mm->flags = (current->mm) ? current->mm->flags : default_dump_filter; - mm->oom_adj = (current->mm) ? current->mm->oom_adj : 0; mm->core_state = NULL; mm->nr_ptes = 0; set_mm_counter(mm, file_rss, 0); diff --git a/mm/oom_kill.c b/mm/oom_kill.c index 175a67a78a9..a7b2460e922 100644 --- a/mm/oom_kill.c +++ b/mm/oom_kill.c @@ -58,7 +58,6 @@ unsigned long badness(struct task_struct *p, unsigned long uptime) unsigned long points, cpu_time, run_time; struct mm_struct *mm; struct task_struct *child; - int oom_adj; task_lock(p); mm = p->mm; @@ -66,11 +65,6 @@ unsigned long badness(struct task_struct *p, unsigned long uptime) task_unlock(p); return 0; } - oom_adj = mm->oom_adj; - if (oom_adj == OOM_DISABLE) { - task_unlock(p); - return 0; - } /* * The memory size of the process is the basis for the badness. @@ -154,15 +148,15 @@ unsigned long badness(struct task_struct *p, unsigned long uptime) points /= 8; /* - * Adjust the score by oom_adj. + * Adjust the score by oomkilladj. */ - if (oom_adj) { - if (oom_adj > 0) { + if (p->oomkilladj) { + if (p->oomkilladj > 0) { if (!points) points = 1; - points <<= oom_adj; + points <<= p->oomkilladj; } else - points >>= -(oom_adj); + points >>= -(p->oomkilladj); } #ifdef DEBUG @@ -257,8 +251,11 @@ static struct task_struct *select_bad_process(unsigned long *ppoints, *ppoints = ULONG_MAX; } + if (p->oomkilladj == OOM_DISABLE) + continue; + points = badness(p, uptime.tv_sec); - if (points > *ppoints) { + if (points > *ppoints || !chosen) { chosen = p; *ppoints = points; } @@ -307,7 +304,8 @@ static void dump_tasks(const struct mem_cgroup *mem) } printk(KERN_INFO "[%5d] %5d %5d %8lu %8lu %3d %3d %s\n", p->pid, __task_cred(p)->uid, p->tgid, mm->total_vm, - get_mm_rss(mm), (int)task_cpu(p), mm->oom_adj, p->comm); + get_mm_rss(mm), (int)task_cpu(p), p->oomkilladj, + p->comm); task_unlock(p); } while_each_thread(g, p); } @@ -325,8 +323,11 @@ static void __oom_kill_task(struct task_struct *p, int verbose) return; } - if (!p->mm) + if (!p->mm) { + WARN_ON(1); + printk(KERN_WARNING "tried to kill an mm-less task!\n"); return; + } if (verbose) printk(KERN_ERR "Killed process %d (%s)\n", @@ -348,13 +349,28 @@ static int oom_kill_task(struct task_struct *p) struct mm_struct *mm; struct task_struct *g, *q; - task_lock(p); mm = p->mm; - if (!mm || mm->oom_adj == OOM_DISABLE) { - task_unlock(p); + + /* WARNING: mm may not be dereferenced since we did not obtain its + * value from get_task_mm(p). This is OK since all we need to do is + * compare mm to q->mm below. + * + * Furthermore, even if mm contains a non-NULL value, p->mm may + * change to NULL at any time since we do not hold task_lock(p). + * However, this is of no concern to us. + */ + + if (mm == NULL) return 1; - } - task_unlock(p); + + /* + * Don't kill the process if any threads are set to OOM_DISABLE + */ + do_each_thread(g, q) { + if (q->mm == mm && q->oomkilladj == OOM_DISABLE) + return 1; + } while_each_thread(g, q); + __oom_kill_task(p, 1); /* @@ -377,11 +393,10 @@ static int oom_kill_process(struct task_struct *p, gfp_t gfp_mask, int order, struct task_struct *c; if (printk_ratelimit()) { - task_lock(current); printk(KERN_WARNING "%s invoked oom-killer: " - "gfp_mask=0x%x, order=%d, oom_adj=%d\n", - current->comm, gfp_mask, order, - current->mm ? current->mm->oom_adj : OOM_DISABLE); + "gfp_mask=0x%x, order=%d, oomkilladj=%d\n", + current->comm, gfp_mask, order, current->oomkilladj); + task_lock(current); cpuset_print_task_mems_allowed(current); task_unlock(current); dump_stack(); @@ -394,9 +409,8 @@ static int oom_kill_process(struct task_struct *p, gfp_t gfp_mask, int order, /* * If the task is already exiting, don't alarm the sysadmin or kill * its children or threads, just set TIF_MEMDIE so it can die quickly - * if its mm is still attached. */ - if (p->mm && (p->flags & PF_EXITING)) { + if (p->flags & PF_EXITING) { __oom_kill_task(p, 0); return 0; } -- GitLab From b2503a9408e44eb0531adc3436c513ea70f91c42 Mon Sep 17 00:00:00 2001 From: Andrew Morton Date: Tue, 18 Aug 2009 14:11:12 -0700 Subject: [PATCH 1221/1342] mmc: add the new linux-mmc mailing list to MAINTAINERS There are a number of individual MMC drivers listed in MAINTAINERS. I didn't modify those records. Perhaps I should have. Cc: Cc: Manuel Lauss Cc: Nicolas Pitre Cc: Pierre Ossman Cc: Pavel Pisa Cc: Jarkko Lavinen Cc: Ben Dooks Cc: Sascha Sommer Cc: Ian Molton Cc: Joseph Chan Cc: Harald Welte Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- MAINTAINERS | 1 + 1 file changed, 1 insertion(+) diff --git a/MAINTAINERS b/MAINTAINERS index ac0fdfd2e50..60299a9a7ad 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -3429,6 +3429,7 @@ F: drivers/mfd/ MULTIMEDIA CARD (MMC), SECURE DIGITAL (SD) AND SDIO SUBSYSTEM S: Orphan +L: linux-mmc@vger.kernel.org F: drivers/mmc/ F: include/linux/mmc/ -- GitLab From b8978784544e8b4e8fbacb558df8580957d4f8a5 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Tue, 18 Aug 2009 14:11:16 -0700 Subject: [PATCH 1222/1342] spi_s3c24xx: fix clock rate calculation Currently the clock rate calculation may round as pleased, which means that it is possible that we will round down and end up with a faster clock rate than intended. Change the calculation to use DIV_ROUND_UP() to ensure that we end up with a clock rate either the same as or lower than the user requested one. Signed-off-by: Ben Dooks Cc: David Brownell Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/spi/spi_s3c24xx.c | 17 +++++++---------- 1 file changed, 7 insertions(+), 10 deletions(-) diff --git a/drivers/spi/spi_s3c24xx.c b/drivers/spi/spi_s3c24xx.c index e0d44af4745..590be85c8f3 100644 --- a/drivers/spi/spi_s3c24xx.c +++ b/drivers/spi/spi_s3c24xx.c @@ -111,6 +111,7 @@ static int s3c24xx_spi_setupxfer(struct spi_device *spi, unsigned int bpw; unsigned int hz; unsigned int div; + unsigned long clk; bpw = t ? t->bits_per_word : spi->bits_per_word; hz = t ? t->speed_hz : spi->max_speed_hz; @@ -120,20 +121,16 @@ static int s3c24xx_spi_setupxfer(struct spi_device *spi, return -EINVAL; } - div = clk_get_rate(hw->clk) / hz; - - /* is clk = pclk / (2 * (pre+1)), or is it - * clk = (pclk * 2) / ( pre + 1) */ - - div /= 2; - - if (div > 0) - div -= 1; + clk = clk_get_rate(hw->clk); + div = DIV_ROUND_UP(clk, hz * 2) - 1; if (div > 255) div = 255; - dev_dbg(&spi->dev, "setting pre-scaler to %d (hz %d)\n", div, hz); + dev_dbg(&spi->dev, "setting pre-scaler to %d (wanted %d, got %ld)\n", + div, hz, clk / (2 * (div + 1))); + + writeb(div, hw->regs + S3C2410_SPPRE); spin_lock(&hw->bitbang.lock); -- GitLab From 191529756633052680dd9d23ad63744ca5aa02a1 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Tue, 18 Aug 2009 14:11:17 -0700 Subject: [PATCH 1223/1342] spi_s3c24xx: fix transfer setup code Since the changes to the bitbang driver, there is the possibility we will be called with either the speed_hz or bpw values zero. We take these to mean that the default values (8 bits per word, or maximum bus speed). Signed-off-by: Ben Dooks Cc: David Brownell Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/spi/spi_s3c24xx.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/spi/spi_s3c24xx.c b/drivers/spi/spi_s3c24xx.c index 590be85c8f3..3f3119d760d 100644 --- a/drivers/spi/spi_s3c24xx.c +++ b/drivers/spi/spi_s3c24xx.c @@ -116,6 +116,12 @@ static int s3c24xx_spi_setupxfer(struct spi_device *spi, bpw = t ? t->bits_per_word : spi->bits_per_word; hz = t ? t->speed_hz : spi->max_speed_hz; + if (!bpw) + bpw = 8; + + if (!hz) + hz = spi->max_speed_hz; + if (bpw != 8) { dev_err(&spi->dev, "invalid bits-per-word (%d)\n", bpw); return -EINVAL; -- GitLab From 28d7a6ae92c099d81cbea08c20be0d2cf7ccd7ca Mon Sep 17 00:00:00 2001 From: Graff Yang Date: Tue, 18 Aug 2009 14:11:17 -0700 Subject: [PATCH 1224/1342] nommu: check fd read permission in validate_mmap_request() According to the POSIX (1003.1-2008), the file descriptor shall have been opened with read permission, regardless of the protection options specified to mmap(). The ltp test cases mmap06/07 need this. Signed-off-by: Graff Yang Acked-by: Paul Mundt Signed-off-by: David Howells Acked-by: Greg Ungerer Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- mm/nommu.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/mm/nommu.c b/mm/nommu.c index 28754c40be9..4bde489ec43 100644 --- a/mm/nommu.c +++ b/mm/nommu.c @@ -919,6 +919,10 @@ static int validate_mmap_request(struct file *file, if (!file->f_op->read) capabilities &= ~BDI_CAP_MAP_COPY; + /* The file shall have been opened with read permission. */ + if (!(file->f_mode & FMODE_READ)) + return -EACCES; + if (flags & MAP_SHARED) { /* do checks for writing, appending and locking */ if ((prot & PROT_WRITE) && -- GitLab From 503f7944fac68f4fdf71f8ebd06907f51eb64515 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Tue, 18 Aug 2009 14:11:18 -0700 Subject: [PATCH 1225/1342] REPORTING-BUGS: add get_maintainer.pl blurb Signed-off-by: Joe Perches Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- REPORTING-BUGS | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/REPORTING-BUGS b/REPORTING-BUGS index ab0c56630a8..55a6074ccbb 100644 --- a/REPORTING-BUGS +++ b/REPORTING-BUGS @@ -15,7 +15,10 @@ worry too much about getting the wrong person. If you are unsure send it to the person responsible for the code relevant to what you were doing. If it occurs repeatably try and describe how to recreate it. That is worth even more than the oops itself. The list of maintainers and -mailing lists is in the MAINTAINERS file in this directory. +mailing lists is in the MAINTAINERS file in this directory. If you +know the file name that causes the problem you can use the following +command in this directory to find some of the maintainers of that file: + perl scripts/get_maintainer.pl -f If it is a security bug, please copy the Security Contact listed in the MAINTAINERS file. They can help coordinate bugfix and disclosure. -- GitLab From 7f9cfb31030737a7fc9a1cbca3fd01bec184c849 Mon Sep 17 00:00:00 2001 From: Bo Liu Date: Tue, 18 Aug 2009 14:11:19 -0700 Subject: [PATCH 1226/1342] mm: build_zonelists(): move clear node_load[] to __build_all_zonelists() If node_load[] is cleared everytime build_zonelists() is called,node_load[] will have no help to find the next node that should appear in the given node's fallback list. Because of the bug, zonelist's node_order is not calculated as expected. This bug affects on big machine, which has asynmetric node distance. [synmetric NUMA's node distance] 0 1 2 0 10 12 12 1 12 10 12 2 12 12 10 [asynmetric NUMA's node distance] 0 1 2 0 10 12 20 1 12 10 14 2 20 14 10 This (my bug) is very old but no one has reported this for a long time. Maybe because the number of asynmetric NUMA is very small and they use cpuset for customizing node memory allocation fallback. [akpm@linux-foundation.org: fix CONFIG_NUMA=n build] Signed-off-by: Bo Liu Reviewed-by: KAMEZAWA Hiroyuki Cc: Mel Gorman Cc: Christoph Lameter Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- mm/page_alloc.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/mm/page_alloc.c b/mm/page_alloc.c index d052abbe306..5cc986eb9f6 100644 --- a/mm/page_alloc.c +++ b/mm/page_alloc.c @@ -2544,7 +2544,6 @@ static void build_zonelists(pg_data_t *pgdat) prev_node = local_node; nodes_clear(used_mask); - memset(node_load, 0, sizeof(node_load)); memset(node_order, 0, sizeof(node_order)); j = 0; @@ -2653,6 +2652,9 @@ static int __build_all_zonelists(void *dummy) { int nid; +#ifdef CONFIG_NUMA + memset(node_load, 0, sizeof(node_load)); +#endif for_each_online_node(nid) { pg_data_t *pgdat = NODE_DATA(nid); -- GitLab From eda1e328556565e211b7450250e40d6de751563a Mon Sep 17 00:00:00 2001 From: Jiri Olsa Date: Tue, 11 Aug 2009 17:29:04 +0200 Subject: [PATCH 1227/1342] tracing: handle broken names in ftrace filter If one filter item (for set_ftrace_filter and set_ftrace_notrace) is being setup by more than 1 consecutive writes (FTRACE_ITER_CONT flag), it won't be handled corretly. I used following program to test/verify: [snip] #include #include #include #include #include int main(int argc, char **argv) { int fd, i; char *file = argv[1]; if (-1 == (fd = open(file, O_WRONLY))) { perror("open failed"); return -1; } for(i = 0; i < (argc - 2); i++) { int len = strlen(argv[2+i]); int cnt, off = 0; while(len) { cnt = write(fd, argv[2+i] + off, len); len -= cnt; off += cnt; } } close(fd); return 0; } [snip] before change: sh-4.0# echo > ./set_ftrace_filter sh-4.0# /test ./set_ftrace_filter "sys" "_open " sh-4.0# cat ./set_ftrace_filter #### all functions enabled #### sh-4.0# after change: sh-4.0# echo > ./set_ftrace_notrace sh-4.0# test ./set_ftrace_notrace "sys" "_open " sh-4.0# cat ./set_ftrace_notrace sys_open sh-4.0# Signed-off-by: Jiri Olsa LKML-Reference: <20090811152904.GA26065@jolsa.lab.eng.brq.redhat.com> Signed-off-by: Steven Rostedt --- kernel/trace/ftrace.c | 17 +++++++++++------ 1 file changed, 11 insertions(+), 6 deletions(-) diff --git a/kernel/trace/ftrace.c b/kernel/trace/ftrace.c index 1e1d23c2630..25edd5cc593 100644 --- a/kernel/trace/ftrace.c +++ b/kernel/trace/ftrace.c @@ -2278,7 +2278,11 @@ ftrace_regex_write(struct file *file, const char __user *ubuf, read++; cnt--; - if (!(iter->flags & ~FTRACE_ITER_CONT)) { + /* + * If the parser haven't finished with the last write, + * continue reading the user input without skipping spaces. + */ + if (!(iter->flags & FTRACE_ITER_CONT)) { /* skip white space */ while (cnt && isspace(ch)) { ret = get_user(ch, ubuf++); @@ -2288,8 +2292,9 @@ ftrace_regex_write(struct file *file, const char __user *ubuf, cnt--; } + /* only spaces were written */ if (isspace(ch)) { - file->f_pos += read; + *ppos += read; ret = read; goto out; } @@ -2319,12 +2324,12 @@ ftrace_regex_write(struct file *file, const char __user *ubuf, if (ret) goto out; iter->buffer_idx = 0; - } else + } else { iter->flags |= FTRACE_ITER_CONT; + iter->buffer[iter->buffer_idx++] = ch; + } - - file->f_pos += read; - + *ppos += read; ret = read; out: mutex_unlock(&ftrace_regex_lock); -- GitLab From e2c6cbd9ace61039d3de39e717195e38f1492aee Mon Sep 17 00:00:00 2001 From: Mathieu Desnoyers Date: Tue, 18 Aug 2009 20:16:55 -0700 Subject: [PATCH 1228/1342] sparc: sys32.S incorrect compat-layer splice() system call I think arch/sparc/kernel/sys32.S has an incorrect splice definition: SIGN2(sys32_splice, sys_splice, %o0, %o1) The splice() prototype looks like : long splice(int fd_in, loff_t *off_in, int fd_out, loff_t *off_out, size_t len, unsigned int flags); So I think we should have : SIGN2(sys32_splice, sys_splice, %o0, %o2) Signed-off-by: Mathieu Desnoyers Signed-off-by: David S. Miller --- arch/sparc/kernel/sys32.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/sparc/kernel/sys32.S b/arch/sparc/kernel/sys32.S index 577f8fab8b6..aed94869ad6 100644 --- a/arch/sparc/kernel/sys32.S +++ b/arch/sparc/kernel/sys32.S @@ -134,7 +134,7 @@ SIGN1(sys32_getpeername, sys_getpeername, %o0) SIGN1(sys32_getsockname, sys_getsockname, %o0) SIGN2(sys32_ioprio_get, sys_ioprio_get, %o0, %o1) SIGN3(sys32_ioprio_set, sys_ioprio_set, %o0, %o1, %o2) -SIGN2(sys32_splice, sys_splice, %o0, %o1) +SIGN2(sys32_splice, sys_splice, %o0, %o2) SIGN2(sys32_sync_file_range, compat_sync_file_range, %o0, %o5) SIGN2(sys32_tee, sys_tee, %o0, %o1) SIGN1(sys32_vmsplice, compat_sys_vmsplice, %o0) -- GitLab From e7a5965a81a29a13cd4994fa23a6a7a1488bcdb6 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Tue, 18 Aug 2009 20:21:40 -0700 Subject: [PATCH 1229/1342] yellowfin: Fix buffer underrun after dev_alloc_skb() failure yellowfin_init_ring() needs to clean up if dev_alloc_skb() fails and should pass an error status up to the caller. This also prevents an buffer underrun if failure occurred in the first iteration. yellowfin_open() which calls yellowfin_init_ring() should free its requested irq upon failure. Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/yellowfin.c | 28 ++++++++++++++++++---------- 1 file changed, 18 insertions(+), 10 deletions(-) diff --git a/drivers/net/yellowfin.c b/drivers/net/yellowfin.c index a07580138e8..c2fd6187773 100644 --- a/drivers/net/yellowfin.c +++ b/drivers/net/yellowfin.c @@ -346,7 +346,7 @@ static int netdev_ioctl(struct net_device *dev, struct ifreq *rq, int cmd); static int yellowfin_open(struct net_device *dev); static void yellowfin_timer(unsigned long data); static void yellowfin_tx_timeout(struct net_device *dev); -static void yellowfin_init_ring(struct net_device *dev); +static int yellowfin_init_ring(struct net_device *dev); static int yellowfin_start_xmit(struct sk_buff *skb, struct net_device *dev); static irqreturn_t yellowfin_interrupt(int irq, void *dev_instance); static int yellowfin_rx(struct net_device *dev); @@ -573,19 +573,24 @@ static int yellowfin_open(struct net_device *dev) { struct yellowfin_private *yp = netdev_priv(dev); void __iomem *ioaddr = yp->base; - int i; + int i, ret; /* Reset the chip. */ iowrite32(0x80000000, ioaddr + DMACtrl); - i = request_irq(dev->irq, &yellowfin_interrupt, IRQF_SHARED, dev->name, dev); - if (i) return i; + ret = request_irq(dev->irq, &yellowfin_interrupt, IRQF_SHARED, dev->name, dev); + if (ret) + return ret; if (yellowfin_debug > 1) printk(KERN_DEBUG "%s: yellowfin_open() irq %d.\n", dev->name, dev->irq); - yellowfin_init_ring(dev); + ret = yellowfin_init_ring(dev); + if (ret) { + free_irq(dev->irq, dev); + return ret; + } iowrite32(yp->rx_ring_dma, ioaddr + RxPtr); iowrite32(yp->tx_ring_dma, ioaddr + TxPtr); @@ -725,10 +730,10 @@ static void yellowfin_tx_timeout(struct net_device *dev) } /* Initialize the Rx and Tx rings, along with various 'dev' bits. */ -static void yellowfin_init_ring(struct net_device *dev) +static int yellowfin_init_ring(struct net_device *dev) { struct yellowfin_private *yp = netdev_priv(dev); - int i; + int i, j; yp->tx_full = 0; yp->cur_rx = yp->cur_tx = 0; @@ -753,6 +758,11 @@ static void yellowfin_init_ring(struct net_device *dev) yp->rx_ring[i].addr = cpu_to_le32(pci_map_single(yp->pci_dev, skb->data, yp->rx_buf_sz, PCI_DMA_FROMDEVICE)); } + if (i != RX_RING_SIZE) { + for (j = 0; j < i; j++) + dev_kfree_skb(yp->rx_skbuff[j]); + return -ENOMEM; + } yp->rx_ring[i-1].dbdma_cmd = cpu_to_le32(CMD_STOP); yp->dirty_rx = (unsigned int)(i - RX_RING_SIZE); @@ -769,8 +779,6 @@ static void yellowfin_init_ring(struct net_device *dev) yp->tx_ring[--i].dbdma_cmd = cpu_to_le32(CMD_STOP | BRANCH_ALWAYS); #else { - int j; - /* Tx ring needs a pair of descriptors, the second for the status. */ for (i = 0; i < TX_RING_SIZE; i++) { j = 2*i; @@ -805,7 +813,7 @@ static void yellowfin_init_ring(struct net_device *dev) } #endif yp->tx_tail_desc = &yp->tx_status[0]; - return; + return 0; } static int yellowfin_start_xmit(struct sk_buff *skb, struct net_device *dev) -- GitLab From 80e6914db18e702549a15dea36fa7ace17f25c50 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 17 Aug 2009 10:22:37 +1000 Subject: [PATCH 1230/1342] drm/radeon/kms: although LVDS might be possible on crtc 1 don't do it. LVDS always requests RMX_FULL, we need to fix it so that doesn't happen before we can enable LVDS on crtc 1. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_legacy_encoders.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/gpu/drm/radeon/radeon_legacy_encoders.c b/drivers/gpu/drm/radeon/radeon_legacy_encoders.c index 34d0f58eb94..9322675ef6d 100644 --- a/drivers/gpu/drm/radeon/radeon_legacy_encoders.c +++ b/drivers/gpu/drm/radeon/radeon_legacy_encoders.c @@ -1066,6 +1066,7 @@ radeon_add_legacy_encoder(struct drm_device *dev, uint32_t encoder_id, uint32_t switch (radeon_encoder->encoder_id) { case ENCODER_OBJECT_ID_INTERNAL_LVDS: + encoder->possible_crtcs = 0x1; drm_encoder_init(dev, encoder, &radeon_legacy_lvds_enc_funcs, DRM_MODE_ENCODER_LVDS); drm_encoder_helper_add(encoder, &radeon_legacy_lvds_helper_funcs); if (rdev->is_atom_bios) -- GitLab From bf8e828b00a5b6a0fea16f452be578c060d57d64 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 17 Aug 2009 10:20:47 +1000 Subject: [PATCH 1231/1342] drm/radeon/kms: memset the allocated framebuffer before using it. This gets rid of some ugliness, we shuold probably find a way for the GPU to zero this. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_fb.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/gpu/drm/radeon/radeon_fb.c b/drivers/gpu/drm/radeon/radeon_fb.c index 3206c0ad7b6..ec383edf5f3 100644 --- a/drivers/gpu/drm/radeon/radeon_fb.c +++ b/drivers/gpu/drm/radeon/radeon_fb.c @@ -574,6 +574,8 @@ int radeonfb_create(struct radeon_device *rdev, goto out_unref; } + memset_io(fbptr, 0, aligned_size); + strcpy(info->fix.id, "radeondrmfb"); info->fix.type = FB_TYPE_PACKED_PIXELS; info->fix.visual = FB_VISUAL_TRUECOLOR; -- GitLab From 6a719e05330ef19acd9392dbbfb95a774776dee5 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 17 Aug 2009 10:19:51 +1000 Subject: [PATCH 1232/1342] drm/kms/radeon: cleanup combios TV table like DDX. The fallback case wasn't getting executed properly if there was no TV table, which my T42 M7 hasn't got. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_combios.c | 48 ++++++++++--------------- 1 file changed, 19 insertions(+), 29 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon_combios.c b/drivers/gpu/drm/radeon/radeon_combios.c index afc4db280b9..2a027e00762 100644 --- a/drivers/gpu/drm/radeon/radeon_combios.c +++ b/drivers/gpu/drm/radeon/radeon_combios.c @@ -685,23 +685,15 @@ static const uint32_t default_tvdac_adj[CHIP_LAST] = { 0x00780000, /* rs480 */ }; -static struct radeon_encoder_tv_dac - *radeon_legacy_get_tv_dac_info_from_table(struct radeon_device *rdev) +static void radeon_legacy_get_tv_dac_info_from_table(struct radeon_device *rdev, + struct radeon_encoder_tv_dac *tv_dac) { - struct radeon_encoder_tv_dac *tv_dac = NULL; - - tv_dac = kzalloc(sizeof(struct radeon_encoder_tv_dac), GFP_KERNEL); - - if (!tv_dac) - return NULL; - tv_dac->ps2_tvdac_adj = default_tvdac_adj[rdev->family]; if ((rdev->flags & RADEON_IS_MOBILITY) && (rdev->family == CHIP_RV250)) tv_dac->ps2_tvdac_adj = 0x00880000; tv_dac->pal_tvdac_adj = tv_dac->ps2_tvdac_adj; tv_dac->ntsc_tvdac_adj = tv_dac->ps2_tvdac_adj; - - return tv_dac; + return; } struct radeon_encoder_tv_dac *radeon_combios_get_tv_dac_info(struct @@ -713,19 +705,18 @@ struct radeon_encoder_tv_dac *radeon_combios_get_tv_dac_info(struct uint16_t dac_info; uint8_t rev, bg, dac; struct radeon_encoder_tv_dac *tv_dac = NULL; + int found = 0; + + tv_dac = kzalloc(sizeof(struct radeon_encoder_tv_dac), GFP_KERNEL); + if (!tv_dac) + return NULL; if (rdev->bios == NULL) - return radeon_legacy_get_tv_dac_info_from_table(rdev); + goto out; /* first check TV table */ dac_info = combios_get_table_offset(dev, COMBIOS_TV_INFO_TABLE); if (dac_info) { - tv_dac = - kzalloc(sizeof(struct radeon_encoder_tv_dac), GFP_KERNEL); - - if (!tv_dac) - return NULL; - rev = RBIOS8(dac_info + 0x3); if (rev > 4) { bg = RBIOS8(dac_info + 0xc) & 0xf; @@ -739,6 +730,7 @@ struct radeon_encoder_tv_dac *radeon_combios_get_tv_dac_info(struct bg = RBIOS8(dac_info + 0x10) & 0xf; dac = RBIOS8(dac_info + 0x11) & 0xf; tv_dac->ntsc_tvdac_adj = (bg << 16) | (dac << 20); + found = 1; } else if (rev > 1) { bg = RBIOS8(dac_info + 0xc) & 0xf; dac = (RBIOS8(dac_info + 0xc) >> 4) & 0xf; @@ -751,22 +743,15 @@ struct radeon_encoder_tv_dac *radeon_combios_get_tv_dac_info(struct bg = RBIOS8(dac_info + 0xe) & 0xf; dac = (RBIOS8(dac_info + 0xe) >> 4) & 0xf; tv_dac->ntsc_tvdac_adj = (bg << 16) | (dac << 20); + found = 1; } - tv_dac->tv_std = radeon_combios_get_tv_info(encoder); - - } else { + } + if (!found) { /* then check CRT table */ dac_info = combios_get_table_offset(dev, COMBIOS_CRT_INFO_TABLE); if (dac_info) { - tv_dac = - kzalloc(sizeof(struct radeon_encoder_tv_dac), - GFP_KERNEL); - - if (!tv_dac) - return NULL; - rev = RBIOS8(dac_info) & 0x3; if (rev < 2) { bg = RBIOS8(dac_info + 0x3) & 0xf; @@ -775,6 +760,7 @@ struct radeon_encoder_tv_dac *radeon_combios_get_tv_dac_info(struct (bg << 16) | (dac << 20); tv_dac->pal_tvdac_adj = tv_dac->ps2_tvdac_adj; tv_dac->ntsc_tvdac_adj = tv_dac->ps2_tvdac_adj; + found = 1; } else { bg = RBIOS8(dac_info + 0x4) & 0xf; dac = RBIOS8(dac_info + 0x5) & 0xf; @@ -782,13 +768,17 @@ struct radeon_encoder_tv_dac *radeon_combios_get_tv_dac_info(struct (bg << 16) | (dac << 20); tv_dac->pal_tvdac_adj = tv_dac->ps2_tvdac_adj; tv_dac->ntsc_tvdac_adj = tv_dac->ps2_tvdac_adj; + found = 1; } } else { DRM_INFO("No TV DAC info found in BIOS\n"); - return radeon_legacy_get_tv_dac_info_from_table(rdev); } } +out: + if (!found) /* fallback to defaults */ + radeon_legacy_get_tv_dac_info_from_table(rdev, tv_dac); + return tv_dac; } -- GitLab From 5ef5f72febfea420ce58f670bad83830a5e5e3de Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 17 Aug 2009 13:11:23 +1000 Subject: [PATCH 1233/1342] drm/kms: teardown crtc correctly when fb is destroyed. If userspace destroys a framebuffer that is in use on a crtc, don't just null it out, tear down the crtc properly so the hw gets turned off. Signed-off-by: Dave Airlie --- drivers/gpu/drm/drm_crtc.c | 40 ++++++++++++-------------------------- 1 file changed, 12 insertions(+), 28 deletions(-) diff --git a/drivers/gpu/drm/drm_crtc.c b/drivers/gpu/drm/drm_crtc.c index 33be210d672..2f631c75f70 100644 --- a/drivers/gpu/drm/drm_crtc.c +++ b/drivers/gpu/drm/drm_crtc.c @@ -257,31 +257,6 @@ void *drm_mode_object_find(struct drm_device *dev, uint32_t id, uint32_t type) } EXPORT_SYMBOL(drm_mode_object_find); -/** - * drm_crtc_from_fb - find the CRTC structure associated with an fb - * @dev: DRM device - * @fb: framebuffer in question - * - * LOCKING: - * Caller must hold mode_config lock. - * - * Find CRTC in the mode_config structure that matches @fb. - * - * RETURNS: - * Pointer to the CRTC or NULL if it wasn't found. - */ -struct drm_crtc *drm_crtc_from_fb(struct drm_device *dev, - struct drm_framebuffer *fb) -{ - struct drm_crtc *crtc; - - list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) { - if (crtc->fb == fb) - return crtc; - } - return NULL; -} - /** * drm_framebuffer_init - initialize a framebuffer * @dev: DRM device @@ -328,11 +303,20 @@ void drm_framebuffer_cleanup(struct drm_framebuffer *fb) { struct drm_device *dev = fb->dev; struct drm_crtc *crtc; + struct drm_mode_set set; + int ret; /* remove from any CRTC */ list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) { - if (crtc->fb == fb) - crtc->fb = NULL; + if (crtc->fb == fb) { + /* should turn off the crtc */ + memset(&set, 0, sizeof(struct drm_mode_set)); + set.crtc = crtc; + set.fb = NULL; + ret = crtc->funcs->set_config(&set); + if (ret) + DRM_ERROR("failed to reset crtc %p when fb was deleted\n", crtc); + } } drm_mode_object_put(dev, &fb->base); @@ -1511,7 +1495,7 @@ int drm_mode_setcrtc(struct drm_device *dev, void *data, set.mode = mode; set.connectors = connector_set; set.num_connectors = crtc_req->count_connectors; - set.fb =fb; + set.fb = fb; ret = crtc->funcs->set_config(&set); out: -- GitLab From 456d8991a795ff5e44dbc1c2a7f8d5b4ed675866 Mon Sep 17 00:00:00 2001 From: Wan ZongShun Date: Tue, 18 Aug 2009 23:34:58 -0700 Subject: [PATCH 1234/1342] net: Rename MAC platform driver for w90p910 platform Due to I modified the corresponding platform device name, so I make the patch to rename MAC platform driver for w90p910 platform. Signed-off-by: Wan ZongShun Signed-off-by: David S. Miller --- drivers/net/arm/w90p910_ether.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/arm/w90p910_ether.c b/drivers/net/arm/w90p910_ether.c index 616fb7985a3..ddd231cb54b 100644 --- a/drivers/net/arm/w90p910_ether.c +++ b/drivers/net/arm/w90p910_ether.c @@ -1080,7 +1080,7 @@ static struct platform_driver w90p910_ether_driver = { .probe = w90p910_ether_probe, .remove = __devexit_p(w90p910_ether_remove), .driver = { - .name = "w90p910-emc", + .name = "nuc900-emc", .owner = THIS_MODULE, }, }; @@ -1101,5 +1101,5 @@ module_exit(w90p910_ether_exit); MODULE_AUTHOR("Wan ZongShun "); MODULE_DESCRIPTION("w90p910 MAC driver!"); MODULE_LICENSE("GPL"); -MODULE_ALIAS("platform:w90p910-emc"); +MODULE_ALIAS("platform:nuc900-emc"); -- GitLab From a9919646d12a13bea7eb74b996686f900dffb120 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Tue, 18 Aug 2009 23:44:08 -0700 Subject: [PATCH 1235/1342] sparc32: Kill trap table freeing code. Normally, srmmu uses different trap table register values to allow determination of the cpu we're on. All of the trap tables have identical content, they just sit at different offsets from the first trap table, and the offset shifted down and masked out determines the cpu we are on. The code tries to free them up when they aren't actually used (don't have all 4 cpus, we're on sun4d, etc.) but that causes problems. For one thing it triggers false positives in the DMA debugging code. And fixing that up while preserving this relative offset thing isn't trivial. So just kill the freeing code, it costs us at most 3 pages, big deal... Signed-off-by: David S. Miller --- arch/sparc/kernel/sun4d_smp.c | 22 ---------------------- arch/sparc/kernel/sun4m_smp.c | 26 -------------------------- 2 files changed, 48 deletions(-) diff --git a/arch/sparc/kernel/sun4d_smp.c b/arch/sparc/kernel/sun4d_smp.c index 54fb02468f0..68791cad7b7 100644 --- a/arch/sparc/kernel/sun4d_smp.c +++ b/arch/sparc/kernel/sun4d_smp.c @@ -162,9 +162,6 @@ extern void cpu_panic(void); */ extern struct linux_prom_registers smp_penguin_ctable; -extern unsigned long trapbase_cpu1[]; -extern unsigned long trapbase_cpu2[]; -extern unsigned long trapbase_cpu3[]; void __init smp4d_boot_cpus(void) { @@ -235,25 +232,6 @@ void __init smp4d_smp_done(void) *prev = first; local_flush_cache_all(); - /* Free unneeded trap tables */ - ClearPageReserved(virt_to_page(trapbase_cpu1)); - init_page_count(virt_to_page(trapbase_cpu1)); - free_page((unsigned long)trapbase_cpu1); - totalram_pages++; - num_physpages++; - - ClearPageReserved(virt_to_page(trapbase_cpu2)); - init_page_count(virt_to_page(trapbase_cpu2)); - free_page((unsigned long)trapbase_cpu2); - totalram_pages++; - num_physpages++; - - ClearPageReserved(virt_to_page(trapbase_cpu3)); - init_page_count(virt_to_page(trapbase_cpu3)); - free_page((unsigned long)trapbase_cpu3); - totalram_pages++; - num_physpages++; - /* Ok, they are spinning and ready to go. */ smp_processors_ready = 1; sun4d_distribute_irqs(); diff --git a/arch/sparc/kernel/sun4m_smp.c b/arch/sparc/kernel/sun4m_smp.c index 960b113d000..762d6eedd94 100644 --- a/arch/sparc/kernel/sun4m_smp.c +++ b/arch/sparc/kernel/sun4m_smp.c @@ -121,9 +121,6 @@ void __cpuinit smp4m_callin(void) */ extern struct linux_prom_registers smp_penguin_ctable; -extern unsigned long trapbase_cpu1[]; -extern unsigned long trapbase_cpu2[]; -extern unsigned long trapbase_cpu3[]; void __init smp4m_boot_cpus(void) { @@ -193,29 +190,6 @@ void __init smp4m_smp_done(void) *prev = first; local_flush_cache_all(); - /* Free unneeded trap tables */ - if (!cpu_isset(1, cpu_present_map)) { - ClearPageReserved(virt_to_page(trapbase_cpu1)); - init_page_count(virt_to_page(trapbase_cpu1)); - free_page((unsigned long)trapbase_cpu1); - totalram_pages++; - num_physpages++; - } - if (!cpu_isset(2, cpu_present_map)) { - ClearPageReserved(virt_to_page(trapbase_cpu2)); - init_page_count(virt_to_page(trapbase_cpu2)); - free_page((unsigned long)trapbase_cpu2); - totalram_pages++; - num_physpages++; - } - if (!cpu_isset(3, cpu_present_map)) { - ClearPageReserved(virt_to_page(trapbase_cpu3)); - init_page_count(virt_to_page(trapbase_cpu3)); - free_page((unsigned long)trapbase_cpu3); - totalram_pages++; - num_physpages++; - } - /* Ok, they are spinning and ready to go. */ } -- GitLab From 2193aa276e2579d9c781c5269521d43f47da9959 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Tue, 18 Aug 2009 23:46:12 -0700 Subject: [PATCH 1236/1342] sparc32: Update defconfig. Signed-off-by: David S. Miller --- arch/sparc/configs/sparc32_defconfig | 74 +++++++++++++++++----------- 1 file changed, 44 insertions(+), 30 deletions(-) diff --git a/arch/sparc/configs/sparc32_defconfig b/arch/sparc/configs/sparc32_defconfig index 8bcd27af724..a0f62a808ed 100644 --- a/arch/sparc/configs/sparc32_defconfig +++ b/arch/sparc/configs/sparc32_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc2 -# Fri Apr 17 04:04:46 2009 +# Linux kernel version: 2.6.31-rc1 +# Tue Aug 18 23:45:52 2009 # # CONFIG_64BIT is not set CONFIG_SPARC=y @@ -17,6 +17,7 @@ CONFIG_GENERIC_ISA_DMA=y CONFIG_ARCH_NO_VIRT_TO_BUS=y CONFIG_OF=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -74,7 +75,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -87,8 +87,13 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y + +# +# Performance Counters +# CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -97,6 +102,10 @@ CONFIG_SLAB=y # CONFIG_MARKERS is not set CONFIG_HAVE_OPROFILE=y CONFIG_HAVE_ARCH_TRACEHOOK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -109,7 +118,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -154,9 +163,9 @@ CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_SUN_PM=y # CONFIG_SPARC_LED is not set CONFIG_SERIAL_CONSOLE=y @@ -264,6 +273,7 @@ CONFIG_IPV6_TUNNEL=m # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -281,7 +291,11 @@ CONFIG_WIRELESS=y CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# +CONFIG_MAC80211_DEFAULT_PS_VALUE=0 # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -335,6 +349,7 @@ CONFIG_MISC_DEVICES=y # EEPROM support # # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -358,10 +373,6 @@ CONFIG_BLK_DEV_SR=m # CONFIG_BLK_DEV_SR_VENDOR is not set CONFIG_CHR_DEV_SG=m # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -379,6 +390,7 @@ CONFIG_SCSI_SPI_ATTRS=y CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_CXGB3_ISCSI is not set +# CONFIG_SCSI_BNX2_ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -387,6 +399,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -401,7 +414,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_QLOGIC_1280 is not set @@ -426,13 +438,16 @@ CONFIG_SCSI_SUNESP=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_DUMMY=m # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -463,6 +478,7 @@ CONFIG_SUNQE=m # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set # CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set @@ -482,6 +498,7 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -629,6 +646,11 @@ CONFIG_HW_RANDOM=m CONFIG_DEVPORT=y # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -668,22 +690,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -# CONFIG_DAB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -776,6 +783,10 @@ CONFIG_RTC_DRV_M48T59=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -799,10 +810,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -985,6 +998,7 @@ CONFIG_KGDB=y CONFIG_KGDB_SERIAL_CONSOLE=y CONFIG_KGDB_TESTS=y # CONFIG_KGDB_TESTS_ON_BOOT is not set +# CONFIG_KMEMCHECK is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_STACK_DEBUG is not set -- GitLab From 1ca3976d8ca8b0b44145994b1433f759a642615b Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Tue, 18 Aug 2009 23:56:21 -0700 Subject: [PATCH 1237/1342] sparc64: Update defconfig. Signed-off-by: David S. Miller --- arch/sparc/configs/sparc64_defconfig | 59 ++++++++++++++++------------ 1 file changed, 34 insertions(+), 25 deletions(-) diff --git a/arch/sparc/configs/sparc64_defconfig b/arch/sparc/configs/sparc64_defconfig index 0123a4c596c..fdddf7a6f72 100644 --- a/arch/sparc/configs/sparc64_defconfig +++ b/arch/sparc/configs/sparc64_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30 -# Tue Jun 16 04:59:36 2009 +# Linux kernel version: 2.6.31-rc1 +# Tue Aug 18 23:56:02 2009 # CONFIG_64BIT=y CONFIG_SPARC=y @@ -26,6 +26,7 @@ CONFIG_ARCH_NO_VIRT_TO_BUS=y CONFIG_OF=y CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -119,6 +120,11 @@ CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_USE_GENERIC_SMP_HELPERS=y + +# +# GCOV-based kernel profiling +# +# CONFIG_GCOV_KERNEL is not set # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -204,7 +210,6 @@ CONFIG_MIGRATION=y CONFIG_PHYS_ADDR_T_64BIT=y CONFIG_ZONE_DMA_FLAG=0 CONFIG_NR_QUICK=1 -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y CONFIG_DEFAULT_MMAP_MIN_ADDR=8192 @@ -410,6 +415,7 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set # CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y @@ -562,6 +568,7 @@ CONFIG_BLK_DEV_DM=m CONFIG_DM_CRYPT=m CONFIG_DM_SNAPSHOT=m CONFIG_DM_MIRROR=m +# CONFIG_DM_LOG_USERSPACE is not set CONFIG_DM_ZERO=m # CONFIG_DM_MULTIPATH is not set # CONFIG_DM_DELAY is not set @@ -573,7 +580,11 @@ CONFIG_DM_ZERO=m # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set @@ -667,6 +678,7 @@ CONFIG_E1000E=m # CONFIG_VIA_VELOCITY is not set CONFIG_TIGON3=m CONFIG_BNX2=m +# CONFIG_CNIC is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set @@ -773,6 +785,7 @@ CONFIG_MOUSE_SERIAL=y # CONFIG_MOUSE_APPLETOUCH is not set # CONFIG_MOUSE_BCM5974 is not set # CONFIG_MOUSE_VSXXXAA is not set +# CONFIG_MOUSE_SYNAPTICS_I2C is not set # CONFIG_INPUT_JOYSTICK is not set # CONFIG_INPUT_TABLET is not set # CONFIG_INPUT_TOUCHSCREEN is not set @@ -870,6 +883,7 @@ CONFIG_I2C_ALGOBIT=y # # I2C system bus drivers (mostly embedded / system-on-chip) # +# CONFIG_I2C_DESIGNWARE is not set # CONFIG_I2C_OCORES is not set # CONFIG_I2C_SIMTEC is not set @@ -898,13 +912,17 @@ CONFIG_I2C_ALGOBIT=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -959,6 +977,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -994,23 +1013,9 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -# CONFIG_DAB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -1284,7 +1289,6 @@ CONFIG_USB=y # # Miscellaneous USB options # -CONFIG_USB_DEVICEFS=y # CONFIG_USB_DEVICE_CLASS is not set # CONFIG_USB_DYNAMIC_MINORS is not set # CONFIG_USB_OTG is not set @@ -1296,6 +1300,7 @@ CONFIG_USB_DEVICEFS=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=m # CONFIG_USB_EHCI_ROOT_HUB_TT is not set # CONFIG_USB_EHCI_TT_NEWSCHED is not set @@ -1374,7 +1379,6 @@ CONFIG_USB_STORAGE=m # CONFIG_USB_LD is not set # CONFIG_USB_TRANCEVIBRATOR is not set # CONFIG_USB_IOWARRIOR is not set -# CONFIG_USB_TEST is not set # CONFIG_USB_ISIGHTFW is not set # CONFIG_USB_VST is not set # CONFIG_USB_GADGET is not set @@ -1420,6 +1424,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1448,6 +1453,10 @@ CONFIG_RTC_DRV_STARFIRE=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1480,11 +1489,11 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y @@ -1560,7 +1569,7 @@ CONFIG_NETWORK_FILESYSTEMS=y # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y CONFIG_SUN_PARTITION=y -CONFIG_NLS=m +CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_NLS_CODEPAGE_437 is not set # CONFIG_NLS_CODEPAGE_737 is not set -- GitLab From 150fe14c1a1f08cb430d8382bf5554c2a168b79b Mon Sep 17 00:00:00 2001 From: Wu Fengguang Date: Wed, 19 Aug 2009 16:58:59 +0800 Subject: [PATCH 1238/1342] ALSA: hda: enable speaker output for Compaq 6530s/6531s HP Compaq 6530s and 6531s internal speaker is silence or becomes silence within 1 minute after fresh boot. It is found that pin 0x1c must be set to PIN_OUT mode to make the speaker work. This is weird - line-in pin 0x1c and speaker pin 0x16 seem to be unrelated. The codec differences before/after patch are: @@ Node 0x17 [Pin Complex] wcaps 0x40020b: Pin Default 0x41a6e130: [N/A] Mic at Ext Rear Conn = Digital, Color = White DefAssociation = 0x3, Sequence = 0x0 Misc = NO_PRESENCE - Pin-ctls: 0x24: IN + Pin-ctls: 0x40: OUT @@ Node 0x1c [Pin Complex] wcaps 0x40018d: Pin Default 0x41813021: [N/A] Line In at Ext Rear Conn = 1/8, Color = Blue DefAssociation = 0x2, Sequence = 0x1 - Pin-ctls: 0x24: IN VREF_80 + Pin-ctls: 0x40: OUT VREF_HIZ Unsolicited: tag=00, enabled=0 Connection: 1 0x24 Tests show that it won't impact (external) Mic recording. Reported-by: "Lin, Ming M" Signed-off-by: Wu Fengguang Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_analog.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/sound/pci/hda/patch_analog.c b/sound/pci/hda/patch_analog.c index e8e6a43865c..f2bb4803417 100644 --- a/sound/pci/hda/patch_analog.c +++ b/sound/pci/hda/patch_analog.c @@ -3823,9 +3823,11 @@ static struct hda_verb ad1884a_laptop_verbs[] = { /* Port-F (int speaker) mixer - route only from analog mixer */ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)}, - /* Port-F pin */ - {0x16, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_HP}, + /* Port-F (int speaker) pin */ + {0x16, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT}, {0x16, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE}, + /* required for compaq 6530s/6531s speaker output */ + {0x1c, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT}, /* Port-C pin - internal mic-in */ {0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_VREF80}, {0x14, AC_VERB_SET_AMP_GAIN_MUTE, 0x7002}, /* raise mic as default */ -- GitLab From ae709440edb2d36f51f5ea51cfab931f45c03e02 Mon Sep 17 00:00:00 2001 From: Wu Fengguang Date: Wed, 19 Aug 2009 17:05:11 +0800 Subject: [PATCH 1239/1342] ALSA: hda: add model for Intel DG45ID/DG45FC boards The BIOS pin configs are in fact correct and shall not be overwritten. Signed-off-by: Wu Fengguang Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_sigmatel.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/sound/pci/hda/patch_sigmatel.c b/sound/pci/hda/patch_sigmatel.c index 456ef6ac12e..6990cfcb6a3 100644 --- a/sound/pci/hda/patch_sigmatel.c +++ b/sound/pci/hda/patch_sigmatel.c @@ -76,6 +76,7 @@ enum { STAC_92HD73XX_AUTO, STAC_92HD73XX_NO_JD, /* no jack-detection */ STAC_92HD73XX_REF, + STAC_92HD73XX_INTEL, STAC_DELL_M6_AMIC, STAC_DELL_M6_DMIC, STAC_DELL_M6_BOTH, @@ -1777,6 +1778,7 @@ static const char *stac92hd73xx_models[STAC_92HD73XX_MODELS] = { [STAC_92HD73XX_AUTO] = "auto", [STAC_92HD73XX_NO_JD] = "no-jd", [STAC_92HD73XX_REF] = "ref", + [STAC_92HD73XX_INTEL] = "intel", [STAC_DELL_M6_AMIC] = "dell-m6-amic", [STAC_DELL_M6_DMIC] = "dell-m6-dmic", [STAC_DELL_M6_BOTH] = "dell-m6", @@ -1789,6 +1791,10 @@ static struct snd_pci_quirk stac92hd73xx_cfg_tbl[] = { "DFI LanParty", STAC_92HD73XX_REF), SND_PCI_QUIRK(PCI_VENDOR_ID_DFI, 0x3101, "DFI LanParty", STAC_92HD73XX_REF), + SND_PCI_QUIRK(PCI_VENDOR_ID_INTEL, 0x5002, + "Intel DG45ID", STAC_92HD73XX_INTEL), + SND_PCI_QUIRK(PCI_VENDOR_ID_INTEL, 0x5003, + "Intel DG45FC", STAC_92HD73XX_INTEL), SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x0254, "Dell Studio 1535", STAC_DELL_M6_DMIC), SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x0255, -- GitLab From fa6963b2481beff8b11f76006fbb63fdbbf2d2d7 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Wed, 19 Aug 2009 11:18:26 +0200 Subject: [PATCH 1240/1342] perf tools: Check perf.data owner Add an owner check to opening perf.data files and a switch to silence it. Because perf-report/perf-annotate are binary parsers reading another users' perf.data file could be a security risk if the file were explicitly engineered to trigger bugs in the parser (we hope of course there are non such bugs, but you never know). Signed-off-by: Peter Zijlstra Cc: Arnaldo Carvalho de Melo Cc: Frederic Weisbecker Cc: Mike Galbraith Cc: Peter Zijlstra Cc: Paul Mackerras LKML-Reference: <20090819092023.896648538@chello.nl> Signed-off-by: Ingo Molnar --- tools/perf/builtin-annotate.c | 7 +++++++ tools/perf/builtin-report.c | 7 +++++++ 2 files changed, 14 insertions(+) diff --git a/tools/perf/builtin-annotate.c b/tools/perf/builtin-annotate.c index 343e7b14bf0..5e17de984dc 100644 --- a/tools/perf/builtin-annotate.c +++ b/tools/perf/builtin-annotate.c @@ -31,6 +31,7 @@ static char *vmlinux = "vmlinux"; static char default_sort_order[] = "comm,symbol"; static char *sort_order = default_sort_order; +static int force; static int input; static int show_mask = SHOW_KERNEL | SHOW_USER | SHOW_HV; @@ -1334,6 +1335,11 @@ static int __cmd_annotate(void) exit(-1); } + if (!force && (stat.st_uid != geteuid())) { + fprintf(stderr, "file: %s not owned by current user\n", input_name); + exit(-1); + } + if (!stat.st_size) { fprintf(stderr, "zero-sized file, nothing to do!\n"); exit(0); @@ -1439,6 +1445,7 @@ static const struct option options[] = { "input file name"), OPT_STRING('s', "symbol", &sym_hist_filter, "symbol", "symbol to annotate"), + OPT_BOOLEAN('f', "force", &force, "don't complain, do it"), OPT_BOOLEAN('v', "verbose", &verbose, "be more verbose (show symbol address, etc)"), OPT_BOOLEAN('D', "dump-raw-trace", &dump_trace, diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c index b53a60fc12d..8b2ec882e6e 100644 --- a/tools/perf/builtin-report.c +++ b/tools/perf/builtin-report.c @@ -38,6 +38,7 @@ static char *dso_list_str, *comm_list_str, *sym_list_str, static struct strlist *dso_list, *comm_list, *sym_list; static char *field_sep; +static int force; static int input; static int show_mask = SHOW_KERNEL | SHOW_USER | SHOW_HV; @@ -1856,6 +1857,11 @@ static int __cmd_report(void) exit(-1); } + if (!force && (stat.st_uid != geteuid())) { + fprintf(stderr, "file: %s not owned by current user\n", input_name); + exit(-1); + } + if (!stat.st_size) { fprintf(stderr, "zero-sized file, nothing to do!\n"); exit(0); @@ -2064,6 +2070,7 @@ static const struct option options[] = { OPT_BOOLEAN('D', "dump-raw-trace", &dump_trace, "dump raw trace in ASCII"), OPT_STRING('k', "vmlinux", &vmlinux, "file", "vmlinux pathname"), + OPT_BOOLEAN('f', "force", &force, "don't complain, do it"), OPT_BOOLEAN('m', "modules", &modules, "load module symbols - WARNING: use only with -k and LIVE kernel"), OPT_BOOLEAN('n', "show-nr-samples", &show_nr_samples, -- GitLab From f833bab87fca5c3ce13778421b1365845843b976 Mon Sep 17 00:00:00 2001 From: Suresh Siddha Date: Mon, 17 Aug 2009 14:34:59 -0700 Subject: [PATCH 1241/1342] clockevent: Prevent dead lock on clockevents_lock Currently clockevents_notify() is called with interrupts enabled at some places and interrupts disabled at some other places. This results in a deadlock in this scenario. cpu A holds clockevents_lock in clockevents_notify() with irqs enabled cpu B waits for clockevents_lock in clockevents_notify() with irqs disabled cpu C doing set_mtrr() which will try to rendezvous of all the cpus. This will result in C and A come to the rendezvous point and waiting for B. B is stuck forever waiting for the spinlock and thus not reaching the rendezvous point. Fix the clockevents code so that clockevents_lock is taken with interrupts disabled and thus avoid the above deadlock. Also call lapic_timer_propagate_broadcast() on the destination cpu so that we avoid calling smp_call_function() in the clockevents notifier chain. This issue left us wondering if we need to change the MTRR rendezvous logic to use stop machine logic (instead of smp_call_function) or add a check in spinlock debug code to see if there are other spinlocks which gets taken under both interrupts enabled/disabled conditions. Signed-off-by: Suresh Siddha Signed-off-by: Venkatesh Pallipadi Cc: "Pallipadi Venkatesh" Cc: "Brown Len" LKML-Reference: <1250544899.2709.210.camel@sbs-t61.sc.intel.com> Signed-off-by: Thomas Gleixner --- arch/x86/kernel/process.c | 6 +----- drivers/acpi/processor_idle.c | 6 ++++-- kernel/time/clockevents.c | 16 ++++++++++------ kernel/time/tick-broadcast.c | 7 +++---- 4 files changed, 18 insertions(+), 17 deletions(-) diff --git a/arch/x86/kernel/process.c b/arch/x86/kernel/process.c index 994dd6a4a2a..071166a4ba8 100644 --- a/arch/x86/kernel/process.c +++ b/arch/x86/kernel/process.c @@ -519,16 +519,12 @@ static void c1e_idle(void) if (!cpumask_test_cpu(cpu, c1e_mask)) { cpumask_set_cpu(cpu, c1e_mask); /* - * Force broadcast so ACPI can not interfere. Needs - * to run with interrupts enabled as it uses - * smp_function_call. + * Force broadcast so ACPI can not interfere. */ - local_irq_enable(); clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_FORCE, &cpu); printk(KERN_INFO "Switch to broadcast mode on CPU%d\n", cpu); - local_irq_disable(); } clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ENTER, &cpu); diff --git a/drivers/acpi/processor_idle.c b/drivers/acpi/processor_idle.c index 0efa59e7e3a..66393d5c4c7 100644 --- a/drivers/acpi/processor_idle.c +++ b/drivers/acpi/processor_idle.c @@ -162,8 +162,9 @@ static void lapic_timer_check_state(int state, struct acpi_processor *pr, pr->power.timer_broadcast_on_state = state; } -static void lapic_timer_propagate_broadcast(struct acpi_processor *pr) +static void lapic_timer_propagate_broadcast(void *arg) { + struct acpi_processor *pr = (struct acpi_processor *) arg; unsigned long reason; reason = pr->power.timer_broadcast_on_state < INT_MAX ? @@ -635,7 +636,8 @@ static int acpi_processor_power_verify(struct acpi_processor *pr) working++; } - lapic_timer_propagate_broadcast(pr); + smp_call_function_single(pr->id, lapic_timer_propagate_broadcast, + pr, 1); return (working); } diff --git a/kernel/time/clockevents.c b/kernel/time/clockevents.c index a6dcd67b041..620b58abdc3 100644 --- a/kernel/time/clockevents.c +++ b/kernel/time/clockevents.c @@ -137,11 +137,12 @@ int clockevents_program_event(struct clock_event_device *dev, ktime_t expires, */ int clockevents_register_notifier(struct notifier_block *nb) { + unsigned long flags; int ret; - spin_lock(&clockevents_lock); + spin_lock_irqsave(&clockevents_lock, flags); ret = raw_notifier_chain_register(&clockevents_chain, nb); - spin_unlock(&clockevents_lock); + spin_unlock_irqrestore(&clockevents_lock, flags); return ret; } @@ -178,16 +179,18 @@ static void clockevents_notify_released(void) */ void clockevents_register_device(struct clock_event_device *dev) { + unsigned long flags; + BUG_ON(dev->mode != CLOCK_EVT_MODE_UNUSED); BUG_ON(!dev->cpumask); - spin_lock(&clockevents_lock); + spin_lock_irqsave(&clockevents_lock, flags); list_add(&dev->list, &clockevent_devices); clockevents_do_notify(CLOCK_EVT_NOTIFY_ADD, dev); clockevents_notify_released(); - spin_unlock(&clockevents_lock); + spin_unlock_irqrestore(&clockevents_lock, flags); } EXPORT_SYMBOL_GPL(clockevents_register_device); @@ -235,8 +238,9 @@ void clockevents_exchange_device(struct clock_event_device *old, void clockevents_notify(unsigned long reason, void *arg) { struct list_head *node, *tmp; + unsigned long flags; - spin_lock(&clockevents_lock); + spin_lock_irqsave(&clockevents_lock, flags); clockevents_do_notify(reason, arg); switch (reason) { @@ -251,7 +255,7 @@ void clockevents_notify(unsigned long reason, void *arg) default: break; } - spin_unlock(&clockevents_lock); + spin_unlock_irqrestore(&clockevents_lock, flags); } EXPORT_SYMBOL_GPL(clockevents_notify); #endif diff --git a/kernel/time/tick-broadcast.c b/kernel/time/tick-broadcast.c index 877dbedc311..c2ec25087a3 100644 --- a/kernel/time/tick-broadcast.c +++ b/kernel/time/tick-broadcast.c @@ -205,11 +205,11 @@ static void tick_handle_periodic_broadcast(struct clock_event_device *dev) * Powerstate information: The system enters/leaves a state, where * affected devices might stop */ -static void tick_do_broadcast_on_off(void *why) +static void tick_do_broadcast_on_off(unsigned long *reason) { struct clock_event_device *bc, *dev; struct tick_device *td; - unsigned long flags, *reason = why; + unsigned long flags; int cpu, bc_stopped; spin_lock_irqsave(&tick_broadcast_lock, flags); @@ -276,8 +276,7 @@ void tick_broadcast_on_off(unsigned long reason, int *oncpu) printk(KERN_ERR "tick-broadcast: ignoring broadcast for " "offline CPU #%d\n", *oncpu); else - smp_call_function_single(*oncpu, tick_do_broadcast_on_off, - &reason, 1); + tick_do_broadcast_on_off(&reason); } /* -- GitLab From 0dc9aa845c20ed1f46c85f229591b811dffc4b3b Mon Sep 17 00:00:00 2001 From: Anton Blanchard Date: Wed, 19 Aug 2009 16:10:16 +0100 Subject: [PATCH 1242/1342] AFS: Documentation updates Fix some issues with the AFS documentation, found when testing AFS on ppc64: - Update AFS features: reading/writing, local caching - Typo in kafs sysfs debug file - Use modprobe instead of insmod in example - Update IPs for grand.central.org Signed-off-by: Anton Blanchard Signed-off-by: David Howells Signed-off-by: Linus Torvalds --- Documentation/filesystems/afs.txt | 26 ++++++++++++-------------- 1 file changed, 12 insertions(+), 14 deletions(-) diff --git a/Documentation/filesystems/afs.txt b/Documentation/filesystems/afs.txt index 12ad6c7f4e5..ffef91c4e0d 100644 --- a/Documentation/filesystems/afs.txt +++ b/Documentation/filesystems/afs.txt @@ -23,15 +23,13 @@ it does support include: (*) Security (currently only AFS kaserver and KerberosIV tickets). - (*) File reading. + (*) File reading and writing. (*) Automounting. -It does not yet support the following AFS features: - - (*) Write support. + (*) Local caching (via fscache). - (*) Local caching. +It does not yet support the following AFS features: (*) pioctl() system call. @@ -56,7 +54,7 @@ They permit the debugging messages to be turned on dynamically by manipulating the masks in the following files: /sys/module/af_rxrpc/parameters/debug - /sys/module/afs/parameters/debug + /sys/module/kafs/parameters/debug ===== @@ -66,9 +64,9 @@ USAGE When inserting the driver modules the root cell must be specified along with a list of volume location server IP addresses: - insmod af_rxrpc.o - insmod rxkad.o - insmod kafs.o rootcell=cambridge.redhat.com:172.16.18.73:172.16.18.91 + modprobe af_rxrpc + modprobe rxkad + modprobe kafs rootcell=cambridge.redhat.com:172.16.18.73:172.16.18.91 The first module is the AF_RXRPC network protocol driver. This provides the RxRPC remote operation protocol and may also be accessed from userspace. See: @@ -81,7 +79,7 @@ is the actual filesystem driver for the AFS filesystem. Once the module has been loaded, more modules can be added by the following procedure: - echo add grand.central.org 18.7.14.88:128.2.191.224 >/proc/fs/afs/cells + echo add grand.central.org 18.9.48.14:128.2.203.61:130.237.48.87 >/proc/fs/afs/cells Where the parameters to the "add" command are the name of a cell and a list of volume location servers within that cell, with the latter separated by colons. @@ -101,7 +99,7 @@ The name of the volume can be suffixes with ".backup" or ".readonly" to specify connection to only volumes of those types. The name of the cell is optional, and if not given during a mount, then the -named volume will be looked up in the cell specified during insmod. +named volume will be looked up in the cell specified during modprobe. Additional cells can be added through /proc (see later section). @@ -163,14 +161,14 @@ THE CELL DATABASE The filesystem maintains an internal database of all the cells it knows and the IP addresses of the volume location servers for those cells. The cell to which -the system belongs is added to the database when insmod is performed by the +the system belongs is added to the database when modprobe is performed by the "rootcell=" argument or, if compiled in, using a "kafs.rootcell=" argument on the kernel command line. Further cells can be added by commands similar to the following: echo add CELLNAME VLADDR[:VLADDR][:VLADDR]... >/proc/fs/afs/cells - echo add grand.central.org 18.7.14.88:128.2.191.224 >/proc/fs/afs/cells + echo add grand.central.org 18.9.48.14:128.2.203.61:130.237.48.87 >/proc/fs/afs/cells No other cell database operations are available at this time. @@ -233,7 +231,7 @@ insmod /tmp/kafs.o rootcell=cambridge.redhat.com:172.16.18.91 mount -t afs \%root.afs. /afs mount -t afs \%cambridge.redhat.com:root.cell. /afs/cambridge.redhat.com/ -echo add grand.central.org 18.7.14.88:128.2.191.224 > /proc/fs/afs/cells +echo add grand.central.org 18.9.48.14:128.2.203.61:130.237.48.87 > /proc/fs/afs/cells mount -t afs "#grand.central.org:root.cell." /afs/grand.central.org/ mount -t afs "#grand.central.org:root.archive." /afs/grand.central.org/archive mount -t afs "#grand.central.org:root.contrib." /afs/grand.central.org/contrib -- GitLab From 3abf2f3639959e4f53f209f93cd4d93fe9356de1 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Wed, 19 Aug 2009 20:05:02 +0200 Subject: [PATCH 1243/1342] ALSA: hda - Fix probe of Toshiba laptops with ALC268 codec There are many variants of Toshiba laptops with ALC268 codec, and it seems that a few of them don't work with model=toshiba preset since they have the secondary ALC268 codec just for HDMI output. This is a regression due to the previous clean-up work to merge all Toshiba quirk entries into a single check. This patch adds the identification of such laptops to apply the standard BIOS-probing method. Unfortunately, Toshiba laptops have all the same PCI SSID, so we need to check the codec SSID to identify each device. Tested-by: Alexey Dobriyan Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_realtek.c | 15 +++++++++++++-- 1 file changed, 13 insertions(+), 2 deletions(-) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index fea976793ae..6f683e451f2 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -12521,8 +12521,6 @@ static struct snd_pci_quirk alc268_cfg_tbl[] = { ALC268_TOSHIBA), SND_PCI_QUIRK(0x1043, 0x1205, "ASUS W7J", ALC268_3ST), SND_PCI_QUIRK(0x1170, 0x0040, "ZEPTO", ALC268_ZEPTO), - SND_PCI_QUIRK_MASK(0x1179, 0xff00, 0xff00, "TOSHIBA A/Lx05", - ALC268_TOSHIBA), SND_PCI_QUIRK(0x14c0, 0x0025, "COMPAL IFL90/JFL-92", ALC268_TOSHIBA), SND_PCI_QUIRK(0x152d, 0x0763, "Diverse (CPR2000)", ALC268_ACER), SND_PCI_QUIRK(0x152d, 0x0771, "Quanta IL1", ALC267_QUANTA_IL1), @@ -12530,6 +12528,15 @@ static struct snd_pci_quirk alc268_cfg_tbl[] = { {} }; +/* Toshiba laptops have no unique PCI SSID but only codec SSID */ +static struct snd_pci_quirk alc268_ssid_cfg_tbl[] = { + SND_PCI_QUIRK(0x1179, 0xff0a, "TOSHIBA X-200", ALC268_AUTO), + SND_PCI_QUIRK(0x1179, 0xff0e, "TOSHIBA X-200 HDMI", ALC268_AUTO), + SND_PCI_QUIRK_MASK(0x1179, 0xff00, 0xff00, "TOSHIBA A/Lx05", + ALC268_TOSHIBA), + {} +}; + static struct alc_config_preset alc268_presets[] = { [ALC267_QUANTA_IL1] = { .mixers = { alc267_quanta_il1_mixer, alc268_beep_mixer }, @@ -12696,6 +12703,10 @@ static int patch_alc268(struct hda_codec *codec) alc268_models, alc268_cfg_tbl); + if (board_config < 0 || board_config >= ALC268_MODEL_LAST) + board_config = snd_hda_check_board_codec_sid_config(codec, + ALC882_MODEL_LAST, alc268_models, alc268_ssid_cfg_tbl); + if (board_config < 0 || board_config >= ALC268_MODEL_LAST) { printk(KERN_INFO "hda_codec: Unknown model for %s, " "trying auto-probe from BIOS...\n", codec->chip_name); -- GitLab From cbb35f8a2858f7e0fff5df598cb286c4bcae5976 Mon Sep 17 00:00:00 2001 From: Randy Dunlap Date: Wed, 19 Aug 2009 12:13:31 -0700 Subject: [PATCH 1244/1342] net: fix ks8851 build errors Fix build errors due to missing Kconfig select of CRC32: ks8851.c:(.text+0x7d2ee): undefined reference to `crc32_le' ks8851.c:(.text+0x7d2f5): undefined reference to `bitrev32' Signed-off-by: Randy Dunlap Signed-off-by: David S. Miller --- drivers/net/Kconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 5f6509a5f64..7a90e7ce5a9 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -1733,6 +1733,7 @@ config KS8851 tristate "Micrel KS8851 SPI" depends on SPI select MII + select CRC32 help SPI driver for Micrel KS8851 SPI attached network chip. -- GitLab From 5416c2663517ebd0be0664c4d4ce3df0b116c059 Mon Sep 17 00:00:00 2001 From: Jeremy Fitzhardinge Date: Mon, 17 Aug 2009 12:25:41 -0700 Subject: [PATCH 1245/1342] x86: make sure load_percpu_segment has no stackprotector load_percpu_segment() is used to set up the per-cpu segment registers, which are also used for -fstack-protector. Make sure that the load_percpu_segment() function doesn't have stackprotector enabled. [ Impact: allow percpu setup before calling stack-protected functions ] Signed-off-by: Jeremy Fitzhardinge --- arch/x86/kernel/cpu/Makefile | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/x86/kernel/cpu/Makefile b/arch/x86/kernel/cpu/Makefile index 4e242f9a06e..8b5b9b625ed 100644 --- a/arch/x86/kernel/cpu/Makefile +++ b/arch/x86/kernel/cpu/Makefile @@ -7,6 +7,10 @@ ifdef CONFIG_FUNCTION_TRACER CFLAGS_REMOVE_common.o = -pg endif +# Make sure load_percpu_segment has no stackprotector +nostackp := $(call cc-option, -fno-stack-protector) +CFLAGS_common.o := $(nostackp) + obj-y := intel_cacheinfo.o addon_cpuid_features.o obj-y += proc.o capflags.o powerflags.o common.o obj-y += vmware.o hypervisor.o -- GitLab From ce2eef33d35cd7b932492b5a81fb0febd2b323cd Mon Sep 17 00:00:00 2001 From: Jeremy Fitzhardinge Date: Mon, 17 Aug 2009 12:26:53 -0700 Subject: [PATCH 1246/1342] xen: rearrange things to fix stackprotector Make sure the stack-protector segment registers are properly set up before calling any functions which may have stack-protection compiled into them. [ Impact: prevent Xen early-boot crash when stack-protector is enabled ] Signed-off-by: Jeremy Fitzhardinge --- arch/x86/xen/Makefile | 4 ++++ arch/x86/xen/enlighten.c | 22 ++++++++++------------ 2 files changed, 14 insertions(+), 12 deletions(-) diff --git a/arch/x86/xen/Makefile b/arch/x86/xen/Makefile index 3b767d03fd6..a5b9288b7da 100644 --- a/arch/x86/xen/Makefile +++ b/arch/x86/xen/Makefile @@ -5,6 +5,10 @@ CFLAGS_REMOVE_time.o = -pg CFLAGS_REMOVE_irq.o = -pg endif +# Make sure early boot has no stackprotector +nostackp := $(call cc-option, -fno-stack-protector) +CFLAGS_enlighten.o := $(nostackp) + obj-y := enlighten.o setup.o multicalls.o mmu.o irq.o \ time.o xen-asm.o xen-asm_$(BITS).o \ grant-table.o suspend.o diff --git a/arch/x86/xen/enlighten.c b/arch/x86/xen/enlighten.c index f09e8c36ee8..edcf72a3c29 100644 --- a/arch/x86/xen/enlighten.c +++ b/arch/x86/xen/enlighten.c @@ -925,10 +925,6 @@ asmlinkage void __init xen_start_kernel(void) xen_domain_type = XEN_PV_DOMAIN; - BUG_ON(memcmp(xen_start_info->magic, "xen-3", 5) != 0); - - xen_setup_features(); - /* Install Xen paravirt ops */ pv_info = xen_info; pv_init_ops = xen_init_ops; @@ -937,8 +933,15 @@ asmlinkage void __init xen_start_kernel(void) pv_apic_ops = xen_apic_ops; pv_mmu_ops = xen_mmu_ops; - xen_init_irq_ops(); +#ifdef CONFIG_X86_64 + /* + * Setup percpu state. We only need to do this for 64-bit + * because 32-bit already has %fs set properly. + */ + load_percpu_segment(0); +#endif + xen_init_irq_ops(); xen_init_cpuid_mask(); #ifdef CONFIG_X86_LOCAL_APIC @@ -948,6 +951,8 @@ asmlinkage void __init xen_start_kernel(void) set_xen_basic_apic_ops(); #endif + xen_setup_features(); + if (xen_feature(XENFEAT_mmu_pt_update_preserve_ad)) { pv_mmu_ops.ptep_modify_prot_start = xen_ptep_modify_prot_start; pv_mmu_ops.ptep_modify_prot_commit = xen_ptep_modify_prot_commit; @@ -955,13 +960,6 @@ asmlinkage void __init xen_start_kernel(void) machine_ops = xen_machine_ops; -#ifdef CONFIG_X86_64 - /* - * Setup percpu state. We only need to do this for 64-bit - * because 32-bit already has %fs set properly. - */ - load_percpu_segment(0); -#endif /* * The only reliable way to retain the initial address of the * percpu gdt_page is to remember it here, so we can go and -- GitLab From 68947b8f9a36f7f7f54ca95e0c6e169bb603e803 Mon Sep 17 00:00:00 2001 From: Jiri Kosina Date: Wed, 19 Aug 2009 22:07:44 -0700 Subject: [PATCH 1247/1342] Input: iforce - support new revision of ACT LABS Force RS Reported-by: cemede@gmail.com Signed-off-by: Jiri Kosina Signed-off-by: Dmitry Torokhov --- drivers/input/joystick/iforce/iforce-main.c | 1 + drivers/input/joystick/iforce/iforce-usb.c | 1 + 2 files changed, 2 insertions(+) diff --git a/drivers/input/joystick/iforce/iforce-main.c b/drivers/input/joystick/iforce/iforce-main.c index baabf830264..f6c688cae33 100644 --- a/drivers/input/joystick/iforce/iforce-main.c +++ b/drivers/input/joystick/iforce/iforce-main.c @@ -74,6 +74,7 @@ static struct iforce_device iforce_device[] = { { 0x05ef, 0x8884, "AVB Mag Turbo Force", btn_avb_wheel, abs_wheel, ff_iforce }, { 0x05ef, 0x8888, "AVB Top Shot Force Feedback Racing Wheel", btn_avb_tw, abs_wheel, ff_iforce }, //? { 0x061c, 0xc0a4, "ACT LABS Force RS", btn_wheel, abs_wheel, ff_iforce }, //? + { 0x061c, 0xc084, "ACT LABS Force RS", btn_wheel, abs_wheel, ff_iforce }, { 0x06f8, 0x0001, "Guillemot Race Leader Force Feedback", btn_wheel, abs_wheel, ff_iforce }, //? { 0x06f8, 0x0004, "Guillemot Force Feedback Racing Wheel", btn_wheel, abs_wheel, ff_iforce }, //? { 0x06f8, 0x0004, "Gullemot Jet Leader 3D", btn_joystick, abs_joystick, ff_iforce }, //? diff --git a/drivers/input/joystick/iforce/iforce-usb.c b/drivers/input/joystick/iforce/iforce-usb.c index f83185aeb51..9f289d8f52c 100644 --- a/drivers/input/joystick/iforce/iforce-usb.c +++ b/drivers/input/joystick/iforce/iforce-usb.c @@ -223,6 +223,7 @@ static struct usb_device_id iforce_usb_ids [] = { { USB_DEVICE(0x05ef, 0x8884) }, /* AVB Mag Turbo Force */ { USB_DEVICE(0x05ef, 0x8888) }, /* AVB Top Shot FFB Racing Wheel */ { USB_DEVICE(0x061c, 0xc0a4) }, /* ACT LABS Force RS */ + { USB_DEVICE(0x061c, 0xc084) }, /* ACT LABS Force RS */ { USB_DEVICE(0x06f8, 0x0001) }, /* Guillemot Race Leader Force Feedback */ { USB_DEVICE(0x06f8, 0x0004) }, /* Guillemot Force Feedback Racing Wheel */ { USB_DEVICE(0x06f8, 0xa302) }, /* Guillemot Jet Leader 3D */ -- GitLab From d3b325f9c25be6d504bc73afce7f92d0e25001d7 Mon Sep 17 00:00:00 2001 From: Petri Gynther Date: Thu, 20 Aug 2009 02:21:27 -0700 Subject: [PATCH 1248/1342] ibm_newemac: emac_close() needs to call netif_carrier_off() When ibm_newemac netdev instance is shutdown with "ifconfig down", the netdev interface does not go properly down. netif_carrier_ok() keeps returning TRUE even after "ifconfig down". The problem can be seen when ibm_newemac instances are slaves of a bonding interface. The bonding interface code uses netif_carrier_ok() to determine the link status of its slaves. When ibm_newemac slave is shutdown with "ifconfig down", the bonding interface won't detect any link status change because netif_carrier_ok() keeps returning TRUE. Signed-off-by: Petri Gynther Signed-off-by: David S. Miller --- drivers/net/ibm_newemac/core.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/net/ibm_newemac/core.c b/drivers/net/ibm_newemac/core.c index beb84213b67..f0f89080371 100644 --- a/drivers/net/ibm_newemac/core.c +++ b/drivers/net/ibm_newemac/core.c @@ -1305,6 +1305,8 @@ static int emac_close(struct net_device *ndev) free_irq(dev->emac_irq, dev); + netif_carrier_off(ndev); + return 0; } -- GitLab From c82f63e411f1b58427c103bd95af2863b1c96dd1 Mon Sep 17 00:00:00 2001 From: Alek Du Date: Sat, 8 Aug 2009 08:46:19 +0800 Subject: [PATCH 1249/1342] PCI: check saved state before restore Without the check, the config space may be filled with zeros. Though the driver should try to avoid call restoring before saving, but the pci layer also should check this. Also removes the existing check in pci_restore_standard_config, since it's superfluous with the new check in restore_state. Acked-by: Rafael J. Wysocki Signed-off-by: Alek Du Signed-off-by: Jesse Barnes --- drivers/pci/pci-driver.c | 2 +- drivers/pci/pci.c | 2 ++ 2 files changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/pci/pci-driver.c b/drivers/pci/pci-driver.c index d76c4c85367..f99bc7f089f 100644 --- a/drivers/pci/pci-driver.c +++ b/drivers/pci/pci-driver.c @@ -508,7 +508,7 @@ static int pci_restore_standard_config(struct pci_dev *pci_dev) return error; } - return pci_dev->state_saved ? pci_restore_state(pci_dev) : 0; + return pci_restore_state(pci_dev); } static void pci_pm_default_resume_noirq(struct pci_dev *pci_dev) diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c index dbd0f947f49..7b70312181d 100644 --- a/drivers/pci/pci.c +++ b/drivers/pci/pci.c @@ -846,6 +846,8 @@ pci_restore_state(struct pci_dev *dev) int i; u32 val; + if (!dev->state_saved) + return 0; /* PCI Express register must be restored first */ pci_restore_pcie_state(dev); -- GitLab From dcc4ec26942d3bae2c5a82ab8346ab53b540a171 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Thu, 20 Aug 2009 11:21:14 -0500 Subject: [PATCH 1250/1342] i2c-omap: Fix I2C status ACK I2C status ack for [RX]RDR and [RX]RDY could cause race conditions of clearing the event twice and a violation of the programing sequence as defined in TRM This patch fixes the same. Signed-off-by: Nishanth Menon Signed-off-by: Moiz Sonasath Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-omap.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index d258b02aef4..94639d0aabd 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -674,7 +674,14 @@ omap_i2c_isr(int this_irq, void *dev_id) err = 0; complete: - omap_i2c_write_reg(dev, OMAP_I2C_STAT_REG, stat); + /* + * Ack the stat in one go, but [R/X]DR and [R/X]RDY should be + * acked after the data operation is complete. + * Ref: TRM SWPU114Q Figure 18-31 + */ + omap_i2c_write_reg(dev, OMAP_I2C_STAT_REG, stat & + ~(OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR | + OMAP_I2C_STAT_XRDY | OMAP_I2C_STAT_XDR)); if (stat & OMAP_I2C_STAT_NACK) { err |= OMAP_I2C_STAT_NACK; -- GitLab From dd11976aea15bde53ce40b076dd5fa462c74f41a Mon Sep 17 00:00:00 2001 From: Moiz Sonasath Date: Thu, 20 Aug 2009 11:21:15 -0500 Subject: [PATCH 1251/1342] i2c-omap: ACK pending [R/X]DR and [R/X]RDY interrupts ACK any pending read/write interrupts before exiting the ISR either after completing the operation [ARDY interrupt] or in case of an error [NACK|AL interrupt] Signed-off-by: Moiz Sonasath Signed-off-by: Vikram Pandita Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-omap.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index 94639d0aabd..16b39f470a7 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -694,6 +694,9 @@ complete: } if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) { + omap_i2c_ack_stat(dev, stat & + (OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR | + OMAP_I2C_STAT_XRDY | OMAP_I2C_STAT_XDR)); omap_i2c_complete_cmd(dev, err); return IRQ_HANDLED; } -- GitLab From 61149787d65b4a2f9c638d363dc65e13cb063e29 Mon Sep 17 00:00:00 2001 From: Moiz Sonasath Date: Thu, 20 Aug 2009 11:21:16 -0500 Subject: [PATCH 1252/1342] i2c-omap: Enable workaround for Errata 1.153 based on Silicon Errata 1.153 has been fixed on OMAP 3630|4430 with the use of a later version of I2C IP block. The errata impacts OMAP 2420|2430|3430, enable the workaround for these based on I2C IP block revision number instead of OMAP CPU type Signed-off-by: Moiz Sonasath Signed-off-by: Vikram Pandita Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-omap.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index 16b39f470a7..827da085813 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -784,7 +784,7 @@ complete: * memory to the I2C interface. */ - if (cpu_is_omap34xx()) { + if (dev->rev <= OMAP_I2C_REV_ON_3430) { while (!(stat & OMAP_I2C_STAT_XUDF)) { if (stat & (OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) { omap_i2c_ack_stat(dev, stat & (OMAP_I2C_STAT_XRDY | OMAP_I2C_STAT_XDR)); -- GitLab From c37faafa7d46622b749437f7d294201a63af4beb Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Thu, 13 Aug 2009 22:14:23 +0200 Subject: [PATCH 1253/1342] i2c-stu300: I2C STU300 stability updates - blk clk is enabled when an irq arrives. The clk should be enabled, but just to make sure. - All error bits are handled no matter state machine state - All irq's will run complete() except for irq's that wasn't an event. - No more looking into status registers just in case an interrupt has happend and the irq handle wasn't executed. - irq_disable/enable are now separete functions. - clk settings calculation changed to round upwards instead of downwards. - Number of address send attempts before giving up is increased to 12 from 10 since it most times take 8 tries before getting through. Signed-off-by: Linus Walleij Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-stu300.c | 157 +++++++++++++++++++------------- 1 file changed, 92 insertions(+), 65 deletions(-) diff --git a/drivers/i2c/busses/i2c-stu300.c b/drivers/i2c/busses/i2c-stu300.c index 182e711318b..d2728a28a8d 100644 --- a/drivers/i2c/busses/i2c-stu300.c +++ b/drivers/i2c/busses/i2c-stu300.c @@ -117,7 +117,8 @@ enum stu300_error { STU300_ERROR_NONE = 0, STU300_ERROR_ACKNOWLEDGE_FAILURE, STU300_ERROR_BUS_ERROR, - STU300_ERROR_ARBITRATION_LOST + STU300_ERROR_ARBITRATION_LOST, + STU300_ERROR_UNKNOWN }; /* timeout waiting for the controller to respond */ @@ -127,7 +128,7 @@ enum stu300_error { * The number of address send athemps tried before giving up. * If the first one failes it seems like 5 to 8 attempts are required. */ -#define NUM_ADDR_RESEND_ATTEMPTS 10 +#define NUM_ADDR_RESEND_ATTEMPTS 12 /* I2C clock speed, in Hz 0-400kHz*/ static unsigned int scl_frequency = 100000; @@ -149,6 +150,7 @@ module_param(scl_frequency, uint, 0644); * @msg_index: index of current message * @msg_len: length of current message */ + struct stu300_dev { struct platform_device *pdev; struct i2c_adapter adapter; @@ -188,6 +190,27 @@ static inline u32 stu300_r8(void __iomem *address) return readl(address) & 0x000000FFU; } +static void stu300_irq_enable(struct stu300_dev *dev) +{ + u32 val; + val = stu300_r8(dev->virtbase + I2C_CR); + val |= I2C_CR_INTERRUPT_ENABLE; + /* Twice paranoia (possible HW glitch) */ + stu300_wr8(val, dev->virtbase + I2C_CR); + stu300_wr8(val, dev->virtbase + I2C_CR); +} + +static void stu300_irq_disable(struct stu300_dev *dev) +{ + u32 val; + val = stu300_r8(dev->virtbase + I2C_CR); + val &= ~I2C_CR_INTERRUPT_ENABLE; + /* Twice paranoia (possible HW glitch) */ + stu300_wr8(val, dev->virtbase + I2C_CR); + stu300_wr8(val, dev->virtbase + I2C_CR); +} + + /* * Tells whether a certain event or events occurred in * response to a command. The events represent states in @@ -196,9 +219,10 @@ static inline u32 stu300_r8(void __iomem *address) * documentation and can only be treated as abstract state * machine states. * - * @ret 0 = event has not occurred, any other value means - * the event occurred. + * @ret 0 = event has not occurred or unknown error, any + * other value means the correct event occurred or an error. */ + static int stu300_event_occurred(struct stu300_dev *dev, enum stu300_event mr_event) { u32 status1; @@ -206,11 +230,28 @@ static int stu300_event_occurred(struct stu300_dev *dev, /* What event happened? */ status1 = stu300_r8(dev->virtbase + I2C_SR1); + if (!(status1 & I2C_SR1_EVF_IND)) /* No event at all */ return 0; + status2 = stu300_r8(dev->virtbase + I2C_SR2); + /* Block any multiple interrupts */ + stu300_irq_disable(dev); + + /* Check for errors first */ + if (status2 & I2C_SR2_AF_IND) { + dev->cmd_err = STU300_ERROR_ACKNOWLEDGE_FAILURE; + return 1; + } else if (status2 & I2C_SR2_BERR_IND) { + dev->cmd_err = STU300_ERROR_BUS_ERROR; + return 1; + } else if (status2 & I2C_SR2_ARLO_IND) { + dev->cmd_err = STU300_ERROR_ARBITRATION_LOST; + return 1; + } + switch (mr_event) { case STU300_EVENT_1: if (status1 & I2C_SR1_ADSL_IND) @@ -221,10 +262,6 @@ static int stu300_event_occurred(struct stu300_dev *dev, case STU300_EVENT_7: case STU300_EVENT_8: if (status1 & I2C_SR1_BTF_IND) { - if (status2 & I2C_SR2_AF_IND) - dev->cmd_err = STU300_ERROR_ACKNOWLEDGE_FAILURE; - else if (status2 & I2C_SR2_BERR_IND) - dev->cmd_err = STU300_ERROR_BUS_ERROR; return 1; } break; @@ -240,8 +277,6 @@ static int stu300_event_occurred(struct stu300_dev *dev, case STU300_EVENT_6: if (status2 & I2C_SR2_ENDAD_IND) { /* First check for any errors */ - if (status2 & I2C_SR2_AF_IND) - dev->cmd_err = STU300_ERROR_ACKNOWLEDGE_FAILURE; return 1; } break; @@ -252,8 +287,15 @@ static int stu300_event_occurred(struct stu300_dev *dev, default: break; } - if (status2 & I2C_SR2_ARLO_IND) - dev->cmd_err = STU300_ERROR_ARBITRATION_LOST; + /* If we get here, we're on thin ice. + * Here we are in a status where we have + * gotten a response that does not match + * what we requested. + */ + dev->cmd_err = STU300_ERROR_UNKNOWN; + dev_err(&dev->pdev->dev, + "Unhandled interrupt! %d sr1: 0x%x sr2: 0x%x\n", + mr_event, status1, status2); return 0; } @@ -262,21 +304,20 @@ static irqreturn_t stu300_irh(int irq, void *data) struct stu300_dev *dev = data; int res; + /* Just make sure that the block is clocked */ + clk_enable(dev->clk); + /* See if this was what we were waiting for */ spin_lock(&dev->cmd_issue_lock); - if (dev->cmd_event != STU300_EVENT_NONE) { - res = stu300_event_occurred(dev, dev->cmd_event); - if (res || dev->cmd_err != STU300_ERROR_NONE) { - u32 val; - - complete(&dev->cmd_complete); - /* Block any multiple interrupts */ - val = stu300_r8(dev->virtbase + I2C_CR); - val &= ~I2C_CR_INTERRUPT_ENABLE; - stu300_wr8(val, dev->virtbase + I2C_CR); - } - } + + res = stu300_event_occurred(dev, dev->cmd_event); + if (res || dev->cmd_err != STU300_ERROR_NONE) + complete(&dev->cmd_complete); + spin_unlock(&dev->cmd_issue_lock); + + clk_disable(dev->clk); + return IRQ_HANDLED; } @@ -308,7 +349,6 @@ static int stu300_start_and_await_event(struct stu300_dev *dev, stu300_wr8(cr_value, dev->virtbase + I2C_CR); ret = wait_for_completion_interruptible_timeout(&dev->cmd_complete, STU300_TIMEOUT); - if (ret < 0) { dev_err(&dev->pdev->dev, "wait_for_completion_interruptible_timeout() " @@ -342,7 +382,6 @@ static int stu300_await_event(struct stu300_dev *dev, enum stu300_event mr_event) { int ret; - u32 val; if (unlikely(irqs_disabled())) { /* TODO: implement polling for this case if need be. */ @@ -354,36 +393,18 @@ static int stu300_await_event(struct stu300_dev *dev, /* Is it already here? */ spin_lock_irq(&dev->cmd_issue_lock); dev->cmd_err = STU300_ERROR_NONE; - if (stu300_event_occurred(dev, mr_event)) { - spin_unlock_irq(&dev->cmd_issue_lock); - goto exit_await_check_err; - } - init_completion(&dev->cmd_complete); - dev->cmd_err = STU300_ERROR_NONE; dev->cmd_event = mr_event; - /* Turn on the I2C interrupt for current operation */ - val = stu300_r8(dev->virtbase + I2C_CR); - val |= I2C_CR_INTERRUPT_ENABLE; - stu300_wr8(val, dev->virtbase + I2C_CR); - - /* Twice paranoia (possible HW glitch) */ - stu300_wr8(val, dev->virtbase + I2C_CR); + init_completion(&dev->cmd_complete); - /* Check again: is it already here? */ - if (unlikely(stu300_event_occurred(dev, mr_event))) { - /* Disable IRQ again. */ - val &= ~I2C_CR_INTERRUPT_ENABLE; - stu300_wr8(val, dev->virtbase + I2C_CR); - spin_unlock_irq(&dev->cmd_issue_lock); - goto exit_await_check_err; - } + /* Turn on the I2C interrupt for current operation */ + stu300_irq_enable(dev); /* Unlock the command block and wait for the event to occur */ spin_unlock_irq(&dev->cmd_issue_lock); + ret = wait_for_completion_interruptible_timeout(&dev->cmd_complete, STU300_TIMEOUT); - if (ret < 0) { dev_err(&dev->pdev->dev, "wait_for_completion_interruptible_timeout()" @@ -401,7 +422,6 @@ static int stu300_await_event(struct stu300_dev *dev, return -ETIMEDOUT; } - exit_await_check_err: if (dev->cmd_err != STU300_ERROR_NONE) { if (mr_event != STU300_EVENT_6) { dev_err(&dev->pdev->dev, "controller " @@ -457,18 +477,19 @@ struct stu300_clkset { }; static const struct stu300_clkset stu300_clktable[] = { - { 0, 0xFFU }, - { 2500000, I2C_OAR2_FR_25_10MHZ }, - { 10000000, I2C_OAR2_FR_10_1667MHZ }, - { 16670000, I2C_OAR2_FR_1667_2667MHZ }, - { 26670000, I2C_OAR2_FR_2667_40MHZ }, - { 40000000, I2C_OAR2_FR_40_5333MHZ }, - { 53330000, I2C_OAR2_FR_5333_66MHZ }, - { 66000000, I2C_OAR2_FR_66_80MHZ }, - { 80000000, I2C_OAR2_FR_80_100MHZ }, + { 0, 0xFFU }, + { 2500000, I2C_OAR2_FR_25_10MHZ }, + { 10000000, I2C_OAR2_FR_10_1667MHZ }, + { 16670000, I2C_OAR2_FR_1667_2667MHZ }, + { 26670000, I2C_OAR2_FR_2667_40MHZ }, + { 40000000, I2C_OAR2_FR_40_5333MHZ }, + { 53330000, I2C_OAR2_FR_5333_66MHZ }, + { 66000000, I2C_OAR2_FR_66_80MHZ }, + { 80000000, I2C_OAR2_FR_80_100MHZ }, { 100000000, 0xFFU }, }; + static int stu300_set_clk(struct stu300_dev *dev, unsigned long clkrate) { @@ -494,10 +515,10 @@ static int stu300_set_clk(struct stu300_dev *dev, unsigned long clkrate) if (dev->speed > 100000) /* Fast Mode I2C */ - val = ((clkrate/dev->speed)-9)/3; + val = ((clkrate/dev->speed) - 9)/3 + 1; else /* Standard Mode I2C */ - val = ((clkrate/dev->speed)-7)/2; + val = ((clkrate/dev->speed) - 7)/2 + 1; /* According to spec the divider must be > 2 */ if (val < 0x002) { @@ -557,6 +578,7 @@ static int stu300_init_hw(struct stu300_dev *dev) */ clkrate = clk_get_rate(dev->clk); ret = stu300_set_clk(dev, clkrate); + if (ret) return ret; /* @@ -641,7 +663,6 @@ static int stu300_xfer_msg(struct i2c_adapter *adap, int attempts = 0; struct stu300_dev *dev = i2c_get_adapdata(adap); - clk_enable(dev->clk); /* Remove this if (0) to trace each and every message. */ @@ -715,14 +736,15 @@ static int stu300_xfer_msg(struct i2c_adapter *adap, if (attempts < NUM_ADDR_RESEND_ATTEMPTS && attempts > 0) { dev_dbg(&dev->pdev->dev, "managed to get address " - "through after %d attempts\n", attempts); + "through after %d attempts\n", attempts); } else if (attempts == NUM_ADDR_RESEND_ATTEMPTS) { dev_dbg(&dev->pdev->dev, "I give up, tried %d times " - "to resend address.\n", - NUM_ADDR_RESEND_ATTEMPTS); + "to resend address.\n", + NUM_ADDR_RESEND_ATTEMPTS); goto exit_disable; } + if (msg->flags & I2C_M_RD) { /* READ: we read the actual bytes one at a time */ for (i = 0; i < msg->len; i++) { @@ -804,8 +826,10 @@ static int stu300_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, { int ret = -1; int i; + struct stu300_dev *dev = i2c_get_adapdata(adap); dev->msg_len = num; + for (i = 0; i < num; i++) { /* * Another driver appears to send stop for each message, @@ -817,6 +841,7 @@ static int stu300_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, dev->msg_index = i; ret = stu300_xfer_msg(adap, &msgs[i], (i == (num - 1))); + if (ret != 0) { num = ret; break; @@ -845,6 +870,7 @@ stu300_probe(struct platform_device *pdev) struct resource *res; int bus_nr; int ret = 0; + char clk_name[] = "I2C0"; dev = kzalloc(sizeof(struct stu300_dev), GFP_KERNEL); if (!dev) { @@ -854,7 +880,8 @@ stu300_probe(struct platform_device *pdev) } bus_nr = pdev->id; - dev->clk = clk_get(&pdev->dev, NULL); + clk_name[3] += (char)bus_nr; + dev->clk = clk_get(&pdev->dev, clk_name); if (IS_ERR(dev->clk)) { ret = PTR_ERR(dev->clk); dev_err(&pdev->dev, "could not retrieve i2c bus clock\n"); -- GitLab From fc0ce23506d943b9eaa731a051769d0e0605eb03 Mon Sep 17 00:00:00 2001 From: Jan Beulich Date: Thu, 20 Aug 2009 16:14:15 +0100 Subject: [PATCH 1254/1342] x86: add vmlinux.lds to targets in arch/x86/boot/compressed/Makefile The absence of vmlinux.lds here keeps .vmlinux.lds.cmd from being included, which in turn leads to it and all its dependents always getting rebuilt independent of whether they are already up-to-date. Signed-off-by: Jan Beulich LKML-Reference: <4A8D84670200007800010D31@vpn.id2.novell.com> Signed-off-by: H. Peter Anvin --- arch/x86/boot/compressed/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/boot/compressed/Makefile b/arch/x86/boot/compressed/Makefile index e2ff504b4dd..f8ed0658404 100644 --- a/arch/x86/boot/compressed/Makefile +++ b/arch/x86/boot/compressed/Makefile @@ -4,7 +4,7 @@ # create a compressed vmlinux image from the original vmlinux # -targets := vmlinux vmlinux.bin vmlinux.bin.gz vmlinux.bin.bz2 vmlinux.bin.lzma head_$(BITS).o misc.o piggy.o +targets := vmlinux.lds vmlinux vmlinux.bin vmlinux.bin.gz vmlinux.bin.bz2 vmlinux.bin.lzma head_$(BITS).o misc.o piggy.o KBUILD_CFLAGS := -m$(BITS) -D__KERNEL__ $(LINUX_INCLUDE) -O2 KBUILD_CFLAGS += -fno-strict-aliasing -fPIC -- GitLab From a8b88d3d49623ac701b5dc996cbd61219c793c7c Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Thu, 20 Aug 2009 18:26:52 +0200 Subject: [PATCH 1255/1342] ocfs2: Add missing lock name There is missing name for NFSSync cluster lock. This makes lockdep unhappy because we end up passing NULL to lockdep when initializing lock key. Fix it. Signed-off-by: Jan Kara Signed-off-by: Joel Becker --- fs/ocfs2/ocfs2_lockid.h | 1 + 1 file changed, 1 insertion(+) diff --git a/fs/ocfs2/ocfs2_lockid.h b/fs/ocfs2/ocfs2_lockid.h index fcdba091af3..c212cf5a2bd 100644 --- a/fs/ocfs2/ocfs2_lockid.h +++ b/fs/ocfs2/ocfs2_lockid.h @@ -108,6 +108,7 @@ static char *ocfs2_lock_type_strings[] = { [OCFS2_LOCK_TYPE_OPEN] = "Open", [OCFS2_LOCK_TYPE_FLOCK] = "Flock", [OCFS2_LOCK_TYPE_QINFO] = "Quota", + [OCFS2_LOCK_TYPE_NFS_SYNC] = "NFSSync", [OCFS2_LOCK_TYPE_ORPHAN_SCAN] = "OrphanScan", }; -- GitLab From e3b2415e281a97ade36d88404094a90cfea838c0 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Fri, 21 Aug 2009 09:47:45 +1000 Subject: [PATCH 1256/1342] drm/radeon/kms: implement the bo busy ioctl properly. The previous patch assumes the ioctl already existed, when it actually didn't. It also didn't return the correct error code. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_gem.c | 2 +- drivers/gpu/drm/radeon/radeon_kms.c | 1 + include/drm/radeon_drm.h | 2 ++ 3 files changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/gpu/drm/radeon/radeon_gem.c b/drivers/gpu/drm/radeon/radeon_gem.c index d4ceff13bbb..14c19980292 100644 --- a/drivers/gpu/drm/radeon/radeon_gem.c +++ b/drivers/gpu/drm/radeon/radeon_gem.c @@ -283,7 +283,7 @@ int radeon_gem_busy_ioctl(struct drm_device *dev, void *data, mutex_lock(&dev->struct_mutex); drm_gem_object_unreference(gobj); mutex_unlock(&dev->struct_mutex); - return 0; + return r; } int radeon_gem_wait_idle_ioctl(struct drm_device *dev, void *data, diff --git a/drivers/gpu/drm/radeon/radeon_kms.c b/drivers/gpu/drm/radeon/radeon_kms.c index d2764bf6b2a..11ed672543b 100644 --- a/drivers/gpu/drm/radeon/radeon_kms.c +++ b/drivers/gpu/drm/radeon/radeon_kms.c @@ -318,5 +318,6 @@ struct drm_ioctl_desc radeon_ioctls_kms[] = { DRM_IOCTL_DEF(DRM_RADEON_INFO, radeon_info_ioctl, DRM_AUTH), DRM_IOCTL_DEF(DRM_RADEON_GEM_SET_TILING, radeon_gem_set_tiling_ioctl, DRM_AUTH), DRM_IOCTL_DEF(DRM_RADEON_GEM_GET_TILING, radeon_gem_get_tiling_ioctl, DRM_AUTH), + DRM_IOCTL_DEF(DRM_RADEON_GEM_BUSY, radeon_gem_busy_ioctl, DRM_AUTH), }; int radeon_max_kms_ioctl = DRM_ARRAY_SIZE(radeon_ioctls_kms); diff --git a/include/drm/radeon_drm.h b/include/drm/radeon_drm.h index f81c3232acc..b43925586b2 100644 --- a/include/drm/radeon_drm.h +++ b/include/drm/radeon_drm.h @@ -508,6 +508,7 @@ typedef struct { #define DRM_RADEON_INFO 0x27 #define DRM_RADEON_GEM_SET_TILING 0x28 #define DRM_RADEON_GEM_GET_TILING 0x29 +#define DRM_RADEON_GEM_BUSY 0x2a #define DRM_IOCTL_RADEON_CP_INIT DRM_IOW( DRM_COMMAND_BASE + DRM_RADEON_CP_INIT, drm_radeon_init_t) #define DRM_IOCTL_RADEON_CP_START DRM_IO( DRM_COMMAND_BASE + DRM_RADEON_CP_START) @@ -548,6 +549,7 @@ typedef struct { #define DRM_IOCTL_RADEON_INFO DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_INFO, struct drm_radeon_info) #define DRM_IOCTL_RADEON_SET_TILING DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_GEM_SET_TILING, struct drm_radeon_gem_set_tiling) #define DRM_IOCTL_RADEON_GET_TILING DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_GEM_GET_TILING, struct drm_radeon_gem_get_tiling) +#define DRM_IOCTL_RADEON_GEM_BUSY DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_GEM_BUSY, struct drm_radeon_gem_busy) typedef struct drm_radeon_init { enum { -- GitLab From 08e4d534743f4e9af3602aebbc1cca9372762028 Mon Sep 17 00:00:00 2001 From: Thomas Hellstrom Date: Thu, 20 Aug 2009 19:02:31 +1000 Subject: [PATCH 1257/1342] drm: Fix sysfs device confusion. The drm sysfs class suspend / resume methods could not distinguish between different device types wich could lead to illegal type casts. Use struct device_type and make sure the class suspend / resume callbacks are aware of those. There is no per device-type suspend / resume. Only new-style PM. Signed-off-by: Thomas Hellstrom Reviewed-by: Jesse Barnes Signed-off-by: Dave Airlie --- drivers/gpu/drm/drm_sysfs.c | 51 +++++++++++++++++++++---------------- 1 file changed, 29 insertions(+), 22 deletions(-) diff --git a/drivers/gpu/drm/drm_sysfs.c b/drivers/gpu/drm/drm_sysfs.c index 85ec31b3ff0..f7a615b80c7 100644 --- a/drivers/gpu/drm/drm_sysfs.c +++ b/drivers/gpu/drm/drm_sysfs.c @@ -22,44 +22,50 @@ #define to_drm_minor(d) container_of(d, struct drm_minor, kdev) #define to_drm_connector(d) container_of(d, struct drm_connector, kdev) +static struct device_type drm_sysfs_device_minor = { + .name = "drm_minor" +}; + /** - * drm_sysfs_suspend - DRM class suspend hook + * drm_class_suspend - DRM class suspend hook * @dev: Linux device to suspend * @state: power state to enter * * Just figures out what the actual struct drm_device associated with * @dev is and calls its suspend hook, if present. */ -static int drm_sysfs_suspend(struct device *dev, pm_message_t state) +static int drm_class_suspend(struct device *dev, pm_message_t state) { - struct drm_minor *drm_minor = to_drm_minor(dev); - struct drm_device *drm_dev = drm_minor->dev; - - if (drm_minor->type == DRM_MINOR_LEGACY && - !drm_core_check_feature(drm_dev, DRIVER_MODESET) && - drm_dev->driver->suspend) - return drm_dev->driver->suspend(drm_dev, state); - + if (dev->type == &drm_sysfs_device_minor) { + struct drm_minor *drm_minor = to_drm_minor(dev); + struct drm_device *drm_dev = drm_minor->dev; + + if (drm_minor->type == DRM_MINOR_LEGACY && + !drm_core_check_feature(drm_dev, DRIVER_MODESET) && + drm_dev->driver->suspend) + return drm_dev->driver->suspend(drm_dev, state); + } return 0; } /** - * drm_sysfs_resume - DRM class resume hook + * drm_class_resume - DRM class resume hook * @dev: Linux device to resume * * Just figures out what the actual struct drm_device associated with * @dev is and calls its resume hook, if present. */ -static int drm_sysfs_resume(struct device *dev) +static int drm_class_resume(struct device *dev) { - struct drm_minor *drm_minor = to_drm_minor(dev); - struct drm_device *drm_dev = drm_minor->dev; - - if (drm_minor->type == DRM_MINOR_LEGACY && - !drm_core_check_feature(drm_dev, DRIVER_MODESET) && - drm_dev->driver->resume) - return drm_dev->driver->resume(drm_dev); - + if (dev->type == &drm_sysfs_device_minor) { + struct drm_minor *drm_minor = to_drm_minor(dev); + struct drm_device *drm_dev = drm_minor->dev; + + if (drm_minor->type == DRM_MINOR_LEGACY && + !drm_core_check_feature(drm_dev, DRIVER_MODESET) && + drm_dev->driver->resume) + return drm_dev->driver->resume(drm_dev); + } return 0; } @@ -99,8 +105,8 @@ struct class *drm_sysfs_create(struct module *owner, char *name) goto err_out; } - class->suspend = drm_sysfs_suspend; - class->resume = drm_sysfs_resume; + class->suspend = drm_class_suspend; + class->resume = drm_class_resume; err = class_create_file(class, &class_attr_version); if (err) @@ -480,6 +486,7 @@ int drm_sysfs_device_add(struct drm_minor *minor) minor->kdev.class = drm_class; minor->kdev.release = drm_sysfs_device_release; minor->kdev.devt = minor->device; + minor->kdev.type = &drm_sysfs_device_minor; if (minor->type == DRM_MINOR_CONTROL) minor_str = "controlD%d"; else if (minor->type == DRM_MINOR_RENDER) -- GitLab From 17782d99502851dc7e48114ee9c5a6d6741cba18 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Fri, 21 Aug 2009 10:07:54 +1000 Subject: [PATCH 1258/1342] drm/radeon/kms: add r100/r200 OQ support. This adds the relocation necessary for OQ support on the r100/r200 chipsets. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 10 ++++++++++ drivers/gpu/drm/radeon/radeon_reg.h | 3 +++ 2 files changed, 13 insertions(+) diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index 90ff8e0ac04..68e728e8be4 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -1091,6 +1091,16 @@ static int r100_packet0_check(struct radeon_cs_parser *p, tmp |= tile_flags; ib[idx] = tmp; break; + case RADEON_RB3D_ZPASS_ADDR: + r = r100_cs_packet_next_reloc(p, &reloc); + if (r) { + DRM_ERROR("No reloc for ib[%d]=0x%04X\n", + idx, reg); + r100_cs_dump_packet(p, pkt); + return r; + } + ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset); + break; default: /* FIXME: we don't want to allow anyothers packet */ break; diff --git a/drivers/gpu/drm/radeon/radeon_reg.h b/drivers/gpu/drm/radeon/radeon_reg.h index 5a098f304ed..5834497b366 100644 --- a/drivers/gpu/drm/radeon/radeon_reg.h +++ b/drivers/gpu/drm/radeon/radeon_reg.h @@ -2337,6 +2337,9 @@ # define RADEON_RE_WIDTH_SHIFT 0 # define RADEON_RE_HEIGHT_SHIFT 16 +#define RADEON_RB3D_ZPASS_DATA 0x3290 +#define RADEON_RB3D_ZPASS_ADDR 0x3294 + #define RADEON_SE_CNTL 0x1c4c # define RADEON_FFACE_CULL_CW (0 << 0) # define RADEON_FFACE_CULL_CCW (1 << 0) -- GitLab From c795b33ba171e41563ab7e25105c0cd4edd81cd7 Mon Sep 17 00:00:00 2001 From: Goldwyn Rodrigues Date: Thu, 20 Aug 2009 13:43:19 -0500 Subject: [PATCH 1259/1342] ocfs2/dlm: Wait on lockres instead of erroring cancel requests In case a downconvert is queued, and a flock receives a signal, BUG_ON(lockres->l_action != OCFS2_AST_INVALID) is triggered because a lock cancel triggers a dlmunlock while an AST is scheduled. To avoid this, allow a LKM_CANCEL to pass through, and let it wait on __dlm_wait_on_lockres(). Signed-off-by: Goldwyn Rodrigues Acked-off-by: Mark Fasheh Signed-off-by: Joel Becker --- fs/ocfs2/dlm/dlmunlock.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/fs/ocfs2/dlm/dlmunlock.c b/fs/ocfs2/dlm/dlmunlock.c index fcf879ed693..756f5b0998e 100644 --- a/fs/ocfs2/dlm/dlmunlock.c +++ b/fs/ocfs2/dlm/dlmunlock.c @@ -122,7 +122,7 @@ static enum dlm_status dlmunlock_common(struct dlm_ctxt *dlm, * that still has AST's pending... */ in_use = !list_empty(&lock->ast_list); spin_unlock(&dlm->ast_lock); - if (in_use) { + if (in_use && !(flags & LKM_CANCEL)) { mlog(ML_ERROR, "lockres %.*s: Someone is calling dlmunlock " "while waiting for an ast!", res->lockname.len, res->lockname.name); @@ -131,7 +131,7 @@ static enum dlm_status dlmunlock_common(struct dlm_ctxt *dlm, spin_lock(&res->spinlock); if (res->state & DLM_LOCK_RES_IN_PROGRESS) { - if (master_node) { + if (master_node && !(flags & LKM_CANCEL)) { mlog(ML_ERROR, "lockres in progress!\n"); spin_unlock(&res->spinlock); return DLM_FORWARD; -- GitLab From 3b7307c2d66dd575ef24b88898b4bc4bddb254f4 Mon Sep 17 00:00:00 2001 From: Dmitry Torokhov Date: Thu, 20 Aug 2009 21:41:04 -0700 Subject: [PATCH 1260/1342] Input: wacom - don't use on-stack memory for report buffers Tested-by: Martin Capitanio Signed-off-by: Dmitry Torokhov --- drivers/input/tablet/wacom_sys.c | 43 +++++++++++++++++++++----------- 1 file changed, 29 insertions(+), 14 deletions(-) diff --git a/drivers/input/tablet/wacom_sys.c b/drivers/input/tablet/wacom_sys.c index a9d5031b855..ea30c983a33 100644 --- a/drivers/input/tablet/wacom_sys.c +++ b/drivers/input/tablet/wacom_sys.c @@ -388,6 +388,32 @@ static int wacom_parse_hid(struct usb_interface *intf, struct hid_descriptor *hi return result; } +static int wacom_query_tablet_data(struct usb_interface *intf) +{ + unsigned char *rep_data; + int limit = 0; + int error; + + rep_data = kmalloc(2, GFP_KERNEL); + if (!rep_data) + return -ENOMEM; + + do { + rep_data[0] = 2; + rep_data[1] = 2; + error = usb_set_report(intf, WAC_HID_FEATURE_REPORT, + 2, rep_data, 2); + if (error >= 0) + error = usb_get_report(intf, + WAC_HID_FEATURE_REPORT, 2, + rep_data, 2); + } while ((error < 0 || rep_data[1] != 2) && limit++ < 5); + + kfree(rep_data); + + return error < 0 ? error : 0; +} + static int wacom_probe(struct usb_interface *intf, const struct usb_device_id *id) { struct usb_device *dev = interface_to_usbdev(intf); @@ -398,7 +424,6 @@ static int wacom_probe(struct usb_interface *intf, const struct usb_device_id *i struct wacom_features *features; struct input_dev *input_dev; int error = -ENOMEM; - char rep_data[2], limit = 0; struct hid_descriptor *hid_desc; wacom = kzalloc(sizeof(struct wacom), GFP_KERNEL); @@ -489,20 +514,10 @@ static int wacom_probe(struct usb_interface *intf, const struct usb_device_id *i /* * Ask the tablet to report tablet data if it is not a Tablet PC. - * Repeat until it succeeds + * Note that if query fails it is not a hard failure. */ - if (wacom_wac->features->type != TABLETPC) { - do { - rep_data[0] = 2; - rep_data[1] = 2; - error = usb_set_report(intf, WAC_HID_FEATURE_REPORT, - 2, rep_data, 2); - if (error >= 0) - error = usb_get_report(intf, - WAC_HID_FEATURE_REPORT, 2, - rep_data, 2); - } while ((error < 0 || rep_data[1] != 2) && limit++ < 5); - } + if (wacom_wac->features->type != TABLETPC) + wacom_query_tablet_data(intf); usb_set_intfdata(intf, wacom); return 0; -- GitLab From 1700f5fde88f9a251037bc86bde538ee32c59905 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Thu, 20 Aug 2009 22:05:53 -0700 Subject: [PATCH 1261/1342] Input: ucb1400_ts - enable ADC Filter This patch enables ADC filtering on UCB1400 codec by default. The benefit from this change is mostly on some Colibri boards where the ADCSYNC pin of the UCB1400 codec isn't connected causing the touchscreen to jitter very badly. This change has no visible effect on boards where the ADCSYNC pin is connected. Signed-off-by: Marek Vasut Tested-by: Palo Revak Signed-off-by: Dmitry Torokhov --- drivers/input/touchscreen/ucb1400_ts.c | 9 +++++++++ include/linux/ucb1400.h | 4 ++++ 2 files changed, 13 insertions(+) diff --git a/drivers/input/touchscreen/ucb1400_ts.c b/drivers/input/touchscreen/ucb1400_ts.c index 6954f550010..3b345f9cf0c 100644 --- a/drivers/input/touchscreen/ucb1400_ts.c +++ b/drivers/input/touchscreen/ucb1400_ts.c @@ -345,6 +345,7 @@ static int ucb1400_ts_detect_irq(struct ucb1400_ts *ucb) static int ucb1400_ts_probe(struct platform_device *dev) { int error, x_res, y_res; + u16 fcsr; struct ucb1400_ts *ucb = dev->dev.platform_data; ucb->ts_idev = input_allocate_device(); @@ -382,6 +383,14 @@ static int ucb1400_ts_probe(struct platform_device *dev) ucb->ts_idev->evbit[0] = BIT_MASK(EV_ABS) | BIT_MASK(EV_KEY); ucb->ts_idev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH); + /* + * Enable ADC filter to prevent horrible jitter on Colibri. + * This also further reduces jitter on boards where ADCSYNC + * pin is connected. + */ + fcsr = ucb1400_reg_read(ucb->ac97, UCB_FCSR); + ucb1400_reg_write(ucb->ac97, UCB_FCSR, fcsr | UCB_FCSR_AVE); + ucb1400_adc_enable(ucb->ac97); x_res = ucb1400_ts_read_xres(ucb); y_res = ucb1400_ts_read_yres(ucb); diff --git a/include/linux/ucb1400.h b/include/linux/ucb1400.h index ed889f4168f..ae779bb8cc0 100644 --- a/include/linux/ucb1400.h +++ b/include/linux/ucb1400.h @@ -73,6 +73,10 @@ #define UCB_ADC_DATA 0x68 #define UCB_ADC_DAT_VALID (1 << 15) + +#define UCB_FCSR 0x6c +#define UCB_FCSR_AVE (1 << 12) + #define UCB_ADC_DAT_MASK 0x3ff #define UCB_ID 0x7e -- GitLab From 9b2fb2da4edfb163842800abbeb4c14bc1759469 Mon Sep 17 00:00:00 2001 From: Pavel Revak Date: Thu, 20 Aug 2009 22:30:54 -0700 Subject: [PATCH 1262/1342] Input: ucb1400_ts - enable interrupt unconditionally Sometimes, when using the touchscreen, it stops working till next restart and the following message is printed: ucb1400: unexpected IE_STATUS = 0x0 The following patch retriggers the touchscreen interrupt unconditionally. This prevents hanging of the touchscreen in case of bogus interrupt occurence. Signed-off-by: Pavel Revak Acked-by: Marek Vasut Signed-off-by: Dmitry Torokhov --- drivers/input/touchscreen/ucb1400_ts.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/input/touchscreen/ucb1400_ts.c b/drivers/input/touchscreen/ucb1400_ts.c index 3b345f9cf0c..3a7a58222f8 100644 --- a/drivers/input/touchscreen/ucb1400_ts.c +++ b/drivers/input/touchscreen/ucb1400_ts.c @@ -170,11 +170,11 @@ static void ucb1400_handle_pending_irq(struct ucb1400_ts *ucb) ucb1400_reg_write(ucb->ac97, UCB_IE_CLEAR, isr); ucb1400_reg_write(ucb->ac97, UCB_IE_CLEAR, 0); - if (isr & UCB_IE_TSPX) { + if (isr & UCB_IE_TSPX) ucb1400_ts_irq_disable(ucb->ac97); - enable_irq(ucb->irq); - } else - printk(KERN_ERR "ucb1400: unexpected IE_STATUS = %#x\n", isr); + else + dev_dbg(&ucb->ts_idev->dev, "ucb1400: unexpected IE_STATUS = %#x\n", isr); + enable_irq(ucb->irq); } static int ucb1400_ts_thread(void *_ucb) -- GitLab From ec9c96ef3cc0124cb94375b17faaa8cff5dfdf97 Mon Sep 17 00:00:00 2001 From: Kyle McMartin Date: Wed, 19 Aug 2009 21:17:08 -0400 Subject: [PATCH 1263/1342] dma-debug: Fix check_unmap null pointer dereference While it's debatable whether or not a NULL device argument to the DMA API functions is valid... since it certainly isn't valid on devices with an IOMMU... dma-debug really shouldn't be dereferencing null pointers either. Guard against that in err_printk and the driver_filter functions. A Fedora rawhide user was seeing this in one of the dvb drivers resulting in an oops on boot. [ A patch has been sent for testing to the driver, but I feel the dma debugging support should be fixed as well. (There's still a pile of legacy garbage in the kernel passing null pointers to dma_{alloc,free}_*. :( ] Signed-off-by: Kyle McMartin Cc: mchehab@infradead.org Cc: Joerg Roedel LKML-Reference: <20090820011708.GP25206@bombadil.infradead.org> Signed-off-by: Ingo Molnar --- lib/dma-debug.c | 28 ++++++++++++++++------------ 1 file changed, 16 insertions(+), 12 deletions(-) diff --git a/lib/dma-debug.c b/lib/dma-debug.c index 65b0d99b6d0..58a9f9fc609 100644 --- a/lib/dma-debug.c +++ b/lib/dma-debug.c @@ -156,9 +156,13 @@ static bool driver_filter(struct device *dev) return true; /* driver filter on and initialized */ - if (current_driver && dev->driver == current_driver) + if (current_driver && dev && dev->driver == current_driver) return true; + /* driver filter on, but we can't filter on a NULL device... */ + if (!dev) + return false; + if (current_driver || !current_driver_name[0]) return false; @@ -183,17 +187,17 @@ static bool driver_filter(struct device *dev) return ret; } -#define err_printk(dev, entry, format, arg...) do { \ - error_count += 1; \ - if (driver_filter(dev) && \ - (show_all_errors || show_num_errors > 0)) { \ - WARN(1, "%s %s: " format, \ - dev_driver_string(dev), \ - dev_name(dev) , ## arg); \ - dump_entry_trace(entry); \ - } \ - if (!show_all_errors && show_num_errors > 0) \ - show_num_errors -= 1; \ +#define err_printk(dev, entry, format, arg...) do { \ + error_count += 1; \ + if (driver_filter(dev) && \ + (show_all_errors || show_num_errors > 0)) { \ + WARN(1, "%s %s: " format, \ + dev ? dev_driver_string(dev) : "NULL", \ + dev ? dev_name(dev) : "NULL", ## arg); \ + dump_entry_trace(entry); \ + } \ + if (!show_all_errors && show_num_errors > 0) \ + show_num_errors -= 1; \ } while (0); /* -- GitLab From 03e860bd9f6a3cca747b0795bed26279a8b420a0 Mon Sep 17 00:00:00 2001 From: "From: Nick Piggin" Date: Fri, 21 Aug 2009 10:09:44 +0200 Subject: [PATCH 1264/1342] btrfs: fix inode rbtree corruption Node may not be inserted over existing node. This causes inode tree corruption and I was seeing crashes in inode_tree_del which I can not reproduce after this patch. The other way to fix this would be to tie inode lifetime in the rbtree with inode while not in freeing state. I had a look at this but it is not so trivial at this point. At least this patch gets things working again. Signed-off-by: Nick Piggin Cc: Chris Mason Acked-by: Yan Zheng Signed-off-by: Jens Axboe --- fs/btrfs/inode.c | 21 ++++++++++++++------- 1 file changed, 14 insertions(+), 7 deletions(-) diff --git a/fs/btrfs/inode.c b/fs/btrfs/inode.c index 272b9b2bea8..59cba180fe8 100644 --- a/fs/btrfs/inode.c +++ b/fs/btrfs/inode.c @@ -3099,8 +3099,12 @@ static void inode_tree_add(struct inode *inode) { struct btrfs_root *root = BTRFS_I(inode)->root; struct btrfs_inode *entry; - struct rb_node **p = &root->inode_tree.rb_node; - struct rb_node *parent = NULL; + struct rb_node **p; + struct rb_node *parent; + +again: + p = &root->inode_tree.rb_node; + parent = NULL; spin_lock(&root->inode_lock); while (*p) { @@ -3108,13 +3112,16 @@ static void inode_tree_add(struct inode *inode) entry = rb_entry(parent, struct btrfs_inode, rb_node); if (inode->i_ino < entry->vfs_inode.i_ino) - p = &(*p)->rb_left; + p = &parent->rb_left; else if (inode->i_ino > entry->vfs_inode.i_ino) - p = &(*p)->rb_right; + p = &parent->rb_right; else { WARN_ON(!(entry->vfs_inode.i_state & (I_WILL_FREE | I_FREEING | I_CLEAR))); - break; + rb_erase(parent, &root->inode_tree); + RB_CLEAR_NODE(parent); + spin_unlock(&root->inode_lock); + goto again; } } rb_link_node(&BTRFS_I(inode)->rb_node, parent, p); @@ -3126,12 +3133,12 @@ static void inode_tree_del(struct inode *inode) { struct btrfs_root *root = BTRFS_I(inode)->root; + spin_lock(&root->inode_lock); if (!RB_EMPTY_NODE(&BTRFS_I(inode)->rb_node)) { - spin_lock(&root->inode_lock); rb_erase(&BTRFS_I(inode)->rb_node, &root->inode_tree); - spin_unlock(&root->inode_lock); RB_CLEAR_NODE(&BTRFS_I(inode)->rb_node); } + spin_unlock(&root->inode_lock); } static noinline void init_btrfs_i(struct inode *inode) -- GitLab From f779b3e513478218cbaaaa0a506d7801cab6fd14 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Wed, 19 Aug 2009 19:11:39 -0400 Subject: [PATCH 1265/1342] drm/radeon: add GET_PARAM/INFO support for Z pipes Needed for occlusion queries on rv530 chips. Signed-off-by: Alex Deucher Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r300.c | 4 +++- drivers/gpu/drm/radeon/r420.c | 13 ++++++++++++- drivers/gpu/drm/radeon/r520.c | 1 - drivers/gpu/drm/radeon/radeon.h | 1 + drivers/gpu/drm/radeon/radeon_cp.c | 9 +++++++++ drivers/gpu/drm/radeon/radeon_drv.h | 5 ++++- drivers/gpu/drm/radeon/radeon_kms.c | 3 +++ drivers/gpu/drm/radeon/radeon_reg.h | 2 ++ drivers/gpu/drm/radeon/radeon_state.c | 3 +++ include/drm/radeon_drm.h | 2 ++ 10 files changed, 39 insertions(+), 4 deletions(-) diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c index c47579dcafa..053f4ec397f 100644 --- a/drivers/gpu/drm/radeon/r300.c +++ b/drivers/gpu/drm/radeon/r300.c @@ -448,6 +448,7 @@ void r300_gpu_init(struct radeon_device *rdev) /* rv350,rv370,rv380 */ rdev->num_gb_pipes = 1; } + rdev->num_z_pipes = 1; gb_tile_config = (R300_ENABLE_TILING | R300_TILE_SIZE_16); switch (rdev->num_gb_pipes) { case 2: @@ -486,7 +487,8 @@ void r300_gpu_init(struct radeon_device *rdev) printk(KERN_WARNING "Failed to wait MC idle while " "programming pipes. Bad things might happen.\n"); } - DRM_INFO("radeon: %d pipes initialized.\n", rdev->num_gb_pipes); + DRM_INFO("radeon: %d quad pipes, %d Z pipes initialized.\n", + rdev->num_gb_pipes, rdev->num_z_pipes); } int r300_ga_reset(struct radeon_device *rdev) diff --git a/drivers/gpu/drm/radeon/r420.c b/drivers/gpu/drm/radeon/r420.c index dea497a979f..97426a6f370 100644 --- a/drivers/gpu/drm/radeon/r420.c +++ b/drivers/gpu/drm/radeon/r420.c @@ -165,7 +165,18 @@ void r420_pipes_init(struct radeon_device *rdev) printk(KERN_WARNING "Failed to wait GUI idle while " "programming pipes. Bad things might happen.\n"); } - DRM_INFO("radeon: %d pipes initialized.\n", rdev->num_gb_pipes); + + if (rdev->family == CHIP_RV530) { + tmp = RREG32(RV530_GB_PIPE_SELECT2); + if ((tmp & 3) == 3) + rdev->num_z_pipes = 2; + else + rdev->num_z_pipes = 1; + } else + rdev->num_z_pipes = 1; + + DRM_INFO("radeon: %d quad pipes, %d z pipes initialized.\n", + rdev->num_gb_pipes, rdev->num_z_pipes); } void r420_gpu_init(struct radeon_device *rdev) diff --git a/drivers/gpu/drm/radeon/r520.c b/drivers/gpu/drm/radeon/r520.c index 09fb0b6ec7d..ebd6b0f7bdf 100644 --- a/drivers/gpu/drm/radeon/r520.c +++ b/drivers/gpu/drm/radeon/r520.c @@ -177,7 +177,6 @@ void r520_gpu_init(struct radeon_device *rdev) */ /* workaround for RV530 */ if (rdev->family == CHIP_RV530) { - WREG32(0x4124, 1); WREG32(0x4128, 0xFF); } r420_pipes_init(rdev); diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index 79ad98264e3..b519fb2fecb 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -655,6 +655,7 @@ struct radeon_device { int usec_timeout; enum radeon_pll_errata pll_errata; int num_gb_pipes; + int num_z_pipes; int disp_priority; /* BIOS */ uint8_t *bios; diff --git a/drivers/gpu/drm/radeon/radeon_cp.c b/drivers/gpu/drm/radeon/radeon_cp.c index d8356827ef1..7a52c461145 100644 --- a/drivers/gpu/drm/radeon/radeon_cp.c +++ b/drivers/gpu/drm/radeon/radeon_cp.c @@ -406,6 +406,15 @@ static void radeon_init_pipes(drm_radeon_private_t *dev_priv) { uint32_t gb_tile_config, gb_pipe_sel = 0; + if ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV530) { + uint32_t z_pipe_sel = RADEON_READ(RV530_GB_PIPE_SELECT2); + if ((z_pipe_sel & 3) == 3) + dev_priv->num_z_pipes = 2; + else + dev_priv->num_z_pipes = 1; + } else + dev_priv->num_z_pipes = 1; + /* RS4xx/RS6xx/R4xx/R5xx */ if ((dev_priv->flags & RADEON_FAMILY_MASK) >= CHIP_R420) { gb_pipe_sel = RADEON_READ(R400_GB_PIPE_SELECT); diff --git a/drivers/gpu/drm/radeon/radeon_drv.h b/drivers/gpu/drm/radeon/radeon_drv.h index 3933f8216a3..6fa32dac4e9 100644 --- a/drivers/gpu/drm/radeon/radeon_drv.h +++ b/drivers/gpu/drm/radeon/radeon_drv.h @@ -100,9 +100,10 @@ * 1.28- Add support for VBL on CRTC2 * 1.29- R500 3D cmd buffer support * 1.30- Add support for occlusion queries + * 1.31- Add support for num Z pipes from GET_PARAM */ #define DRIVER_MAJOR 1 -#define DRIVER_MINOR 30 +#define DRIVER_MINOR 31 #define DRIVER_PATCHLEVEL 0 /* @@ -329,6 +330,7 @@ typedef struct drm_radeon_private { resource_size_t fb_aper_offset; int num_gb_pipes; + int num_z_pipes; int track_flush; drm_local_map_t *mmio; @@ -689,6 +691,7 @@ extern void r600_page_table_cleanup(struct drm_device *dev, struct drm_ati_pciga /* pipe config regs */ #define R400_GB_PIPE_SELECT 0x402c +#define RV530_GB_PIPE_SELECT2 0x4124 #define R500_DYN_SCLK_PWMEM_PIPE 0x000d /* PLL */ #define R300_GB_TILE_CONFIG 0x4018 # define R300_ENABLE_TILING (1 << 0) diff --git a/drivers/gpu/drm/radeon/radeon_kms.c b/drivers/gpu/drm/radeon/radeon_kms.c index 11ed672543b..dce09ada32b 100644 --- a/drivers/gpu/drm/radeon/radeon_kms.c +++ b/drivers/gpu/drm/radeon/radeon_kms.c @@ -95,6 +95,9 @@ int radeon_info_ioctl(struct drm_device *dev, void *data, struct drm_file *filp) case RADEON_INFO_NUM_GB_PIPES: value = rdev->num_gb_pipes; break; + case RADEON_INFO_NUM_Z_PIPES: + value = rdev->num_z_pipes; + break; default: DRM_DEBUG("Invalid request %d\n", info->request); return -EINVAL; diff --git a/drivers/gpu/drm/radeon/radeon_reg.h b/drivers/gpu/drm/radeon/radeon_reg.h index 5834497b366..4df43f62c67 100644 --- a/drivers/gpu/drm/radeon/radeon_reg.h +++ b/drivers/gpu/drm/radeon/radeon_reg.h @@ -3574,4 +3574,6 @@ #define RADEON_SCRATCH_REG4 0x15f0 #define RADEON_SCRATCH_REG5 0x15f4 +#define RV530_GB_PIPE_SELECT2 0x4124 + #endif diff --git a/drivers/gpu/drm/radeon/radeon_state.c b/drivers/gpu/drm/radeon/radeon_state.c index 46645f3e032..2882f40d5ec 100644 --- a/drivers/gpu/drm/radeon/radeon_state.c +++ b/drivers/gpu/drm/radeon/radeon_state.c @@ -3081,6 +3081,9 @@ static int radeon_cp_getparam(struct drm_device *dev, void *data, struct drm_fil case RADEON_PARAM_NUM_GB_PIPES: value = dev_priv->num_gb_pipes; break; + case RADEON_PARAM_NUM_Z_PIPES: + value = dev_priv->num_z_pipes; + break; default: DRM_DEBUG("Invalid parameter %d\n", param->param); return -EINVAL; diff --git a/include/drm/radeon_drm.h b/include/drm/radeon_drm.h index b43925586b2..2ba61e18fc8 100644 --- a/include/drm/radeon_drm.h +++ b/include/drm/radeon_drm.h @@ -709,6 +709,7 @@ typedef struct drm_radeon_indirect { #define RADEON_PARAM_FB_LOCATION 14 /* FB location */ #define RADEON_PARAM_NUM_GB_PIPES 15 /* num GB pipes */ #define RADEON_PARAM_DEVICE_ID 16 +#define RADEON_PARAM_NUM_Z_PIPES 17 /* num Z pipes */ typedef struct drm_radeon_getparam { int param; @@ -897,6 +898,7 @@ struct drm_radeon_cs { #define RADEON_INFO_DEVICE_ID 0x00 #define RADEON_INFO_NUM_GB_PIPES 0x01 +#define RADEON_INFO_NUM_Z_PIPES 0x02 struct drm_radeon_info { uint32_t request; -- GitLab From 4a683bf94b8a10e2bb0da07aec3ac0a55e5de61f Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Fri, 21 Aug 2009 12:53:36 +0200 Subject: [PATCH 1266/1342] tracing: Fix too large stack usage in do_one_initcall() One of my testboxes triggered this nasty stack overflow crash during SCSI probing: [ 5.874004] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.875004] device: 'sda': device_add [ 5.878004] BUG: unable to handle kernel NULL pointer dereference at 00000a0c [ 5.878004] IP: [] print_context_stack+0x81/0x110 [ 5.878004] *pde = 00000000 [ 5.878004] Thread overran stack, or stack corrupted [ 5.878004] Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC [ 5.878004] last sysfs file: [ 5.878004] [ 5.878004] Pid: 1, comm: swapper Not tainted (2.6.31-rc6-tip-01272-g9919e28-dirty #5685) [ 5.878004] EIP: 0060:[] EFLAGS: 00010083 CPU: 0 [ 5.878004] EIP is at print_context_stack+0x81/0x110 [ 5.878004] EAX: cf8a3000 EBX: cf8a3fe4 ECX: 00000049 EDX: 00000000 [ 5.878004] ESI: b1cfce84 EDI: 00000000 EBP: cf8a3018 ESP: cf8a2ff4 [ 5.878004] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 [ 5.878004] Process swapper (pid: 1, ti=cf8a2000 task=cf8a8000 task.ti=cf8a3000) [ 5.878004] Stack: [ 5.878004] b1004867 fffff000 cf8a3ffc [ 5.878004] Call Trace: [ 5.878004] [] ? kernel_thread_helper+0x7/0x10 [ 5.878004] BUG: unable to handle kernel NULL pointer dereference at 00000a0c [ 5.878004] IP: [] print_context_stack+0x81/0x110 [ 5.878004] *pde = 00000000 [ 5.878004] Thread overran stack, or stack corrupted [ 5.878004] Oops: 0000 [#2] PREEMPT SMP DEBUG_PAGEALLOC The oops did not reveal any more details about the real stack that we have and the system got into an infinite loop of recursive pagefaults. So i booted with CONFIG_STACK_TRACER=y and the 'stacktrace' boot parameter. The box did not crash (timings/conditions probably changed a tiny bit to trigger the catastrophic crash), but the /debug/tracing/stack_trace file was rather revealing: Depth Size Location (72 entries) ----- ---- -------- 0) 3704 52 __change_page_attr+0xb8/0x290 1) 3652 24 __change_page_attr_set_clr+0x43/0x90 2) 3628 60 kernel_map_pages+0x108/0x120 3) 3568 40 prep_new_page+0x7d/0x130 4) 3528 84 get_page_from_freelist+0x106/0x420 5) 3444 116 __alloc_pages_nodemask+0xd7/0x550 6) 3328 36 allocate_slab+0xb1/0x100 7) 3292 36 new_slab+0x1c/0x160 8) 3256 36 __slab_alloc+0x133/0x2b0 9) 3220 4 kmem_cache_alloc+0x1bb/0x1d0 10) 3216 108 create_object+0x28/0x250 11) 3108 40 kmemleak_alloc+0x81/0xc0 12) 3068 24 kmem_cache_alloc+0x162/0x1d0 13) 3044 52 scsi_pool_alloc_command+0x29/0x70 14) 2992 20 scsi_host_alloc_command+0x22/0x70 15) 2972 24 __scsi_get_command+0x1b/0x90 16) 2948 28 scsi_get_command+0x35/0x90 17) 2920 24 scsi_setup_blk_pc_cmnd+0xd4/0x100 18) 2896 128 sd_prep_fn+0x332/0xa70 19) 2768 36 blk_peek_request+0xe7/0x1d0 20) 2732 56 scsi_request_fn+0x54/0x520 21) 2676 12 __generic_unplug_device+0x2b/0x40 22) 2664 24 blk_execute_rq_nowait+0x59/0x80 23) 2640 172 blk_execute_rq+0x6b/0xb0 24) 2468 32 scsi_execute+0xe0/0x140 25) 2436 64 scsi_execute_req+0x152/0x160 26) 2372 60 scsi_vpd_inquiry+0x6c/0x90 27) 2312 44 scsi_get_vpd_page+0x112/0x160 28) 2268 52 sd_revalidate_disk+0x1df/0x320 29) 2216 92 rescan_partitions+0x98/0x330 30) 2124 52 __blkdev_get+0x309/0x350 31) 2072 8 blkdev_get+0xf/0x20 32) 2064 44 register_disk+0xff/0x120 33) 2020 36 add_disk+0x6e/0xb0 34) 1984 44 sd_probe_async+0xfb/0x1d0 35) 1940 44 __async_schedule+0xf4/0x1b0 36) 1896 8 async_schedule+0x12/0x20 37) 1888 60 sd_probe+0x305/0x360 38) 1828 44 really_probe+0x63/0x170 39) 1784 36 driver_probe_device+0x5d/0x60 40) 1748 16 __device_attach+0x49/0x50 41) 1732 32 bus_for_each_drv+0x5b/0x80 42) 1700 24 device_attach+0x6b/0x70 43) 1676 16 bus_attach_device+0x47/0x60 44) 1660 76 device_add+0x33d/0x400 45) 1584 52 scsi_sysfs_add_sdev+0x6a/0x2c0 46) 1532 108 scsi_add_lun+0x44b/0x460 47) 1424 116 scsi_probe_and_add_lun+0x182/0x4e0 48) 1308 36 __scsi_add_device+0xd9/0xe0 49) 1272 44 ata_scsi_scan_host+0x10b/0x190 50) 1228 24 async_port_probe+0x96/0xd0 51) 1204 44 __async_schedule+0xf4/0x1b0 52) 1160 8 async_schedule+0x12/0x20 53) 1152 48 ata_host_register+0x171/0x1d0 54) 1104 60 ata_pci_sff_activate_host+0xf3/0x230 55) 1044 44 ata_pci_sff_init_one+0xea/0x100 56) 1000 48 amd_init_one+0xb2/0x190 57) 952 8 local_pci_probe+0x13/0x20 58) 944 32 pci_device_probe+0x68/0x90 59) 912 44 really_probe+0x63/0x170 60) 868 36 driver_probe_device+0x5d/0x60 61) 832 20 __driver_attach+0x89/0xa0 62) 812 32 bus_for_each_dev+0x5b/0x80 63) 780 12 driver_attach+0x1e/0x20 64) 768 72 bus_add_driver+0x14b/0x2d0 65) 696 36 driver_register+0x6e/0x150 66) 660 20 __pci_register_driver+0x53/0xc0 67) 640 8 amd_init+0x14/0x16 68) 632 572 do_one_initcall+0x2b/0x1d0 69) 60 12 do_basic_setup+0x56/0x6a 70) 48 20 kernel_init+0x84/0xce 71) 28 28 kernel_thread_helper+0x7/0x10 There's a lot of fat functions on that stack trace, but the largest of all is do_one_initcall(). This is due to the boot trace entry variables being on the stack. Fixing this is relatively easy, initcalls are fundamentally serialized, so we can move the local variables to file scope. Note that this large stack footprint was present for a couple of months already - what pushed my system over the edge was the addition of kmemleak to the call-chain: 6) 3328 36 allocate_slab+0xb1/0x100 7) 3292 36 new_slab+0x1c/0x160 8) 3256 36 __slab_alloc+0x133/0x2b0 9) 3220 4 kmem_cache_alloc+0x1bb/0x1d0 10) 3216 108 create_object+0x28/0x250 11) 3108 40 kmemleak_alloc+0x81/0xc0 12) 3068 24 kmem_cache_alloc+0x162/0x1d0 13) 3044 52 scsi_pool_alloc_command+0x29/0x70 This pushes the total to ~3800 bytes, only a tiny bit more was needed to corrupt the on-kernel-stack thread_info. The fix reduces the stack footprint from 572 bytes to 28 bytes. Cc: Peter Zijlstra Cc: Thomas Gleixner Cc: Frederic Weisbecker Cc: Steven Rostedt Cc: Catalin Marinas Cc: Jens Axboe Cc: Linus Torvalds Cc: LKML-Reference: Signed-off-by: Ingo Molnar --- init/main.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/init/main.c b/init/main.c index 2c5ade79eb8..98e679e3494 100644 --- a/init/main.c +++ b/init/main.c @@ -733,13 +733,14 @@ static void __init do_ctors(void) int initcall_debug; core_param(initcall_debug, initcall_debug, bool, 0644); +static char msgbuf[64]; +static struct boot_trace_call call; +static struct boot_trace_ret ret; + int do_one_initcall(initcall_t fn) { int count = preempt_count(); ktime_t calltime, delta, rettime; - char msgbuf[64]; - struct boot_trace_call call; - struct boot_trace_ret ret; if (initcall_debug) { call.caller = task_pid_nr(current); -- GitLab From 4464fcaa9cbfc9c551956b48af203e2f775ca892 Mon Sep 17 00:00:00 2001 From: Peter Zijlstra Date: Fri, 21 Aug 2009 17:19:36 +0200 Subject: [PATCH 1267/1342] perf_counter: Fix typo in read() output generation When you iterate a list, using the iterator is useful. Before: ID: 5 ID: 5 ID: 5 ID: 5 EVNT: 0x40088b scale: nan ID: 5 CNT: 1006252 ID: 6 CNT: 1011090 ID: 7 CNT: 1011196 ID: 8 CNT: 1011095 EVNT: 0x40088c scale: 1.000000 ID: 5 CNT: 2003065 ID: 6 CNT: 2011671 ID: 7 CNT: 2012620 ID: 8 CNT: 2013479 EVNT: 0x40088c scale: 1.000000 ID: 5 CNT: 3002390 ID: 6 CNT: 3015996 ID: 7 CNT: 3018019 ID: 8 CNT: 3020006 EVNT: 0x40088b scale: 1.000000 ID: 5 CNT: 4002406 ID: 6 CNT: 4021120 ID: 7 CNT: 4024241 ID: 8 CNT: 4027059 After: ID: 1 ID: 2 ID: 3 ID: 4 EVNT: 0x400889 scale: nan ID: 1 CNT: 1005270 ID: 2 CNT: 1009833 ID: 3 CNT: 1010065 ID: 4 CNT: 1010088 EVNT: 0x400898 scale: nan ID: 1 CNT: 2001531 ID: 2 CNT: 2022309 ID: 3 CNT: 2022470 ID: 4 CNT: 2022627 EVNT: 0x400888 scale: 0.489467 ID: 1 CNT: 3001261 ID: 2 CNT: 3027088 ID: 3 CNT: 3027941 ID: 4 CNT: 3028762 Reported-by: stephane eranian Signed-off-by: Peter Zijlstra Cc: Paul Mackerras Cc: Corey J Ashford Cc: perfmon2-devel LKML-Reference: <1250867976.7538.73.camel@twins> Signed-off-by: Ingo Molnar --- kernel/perf_counter.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c index 36f65e2b8b5..f274e195988 100644 --- a/kernel/perf_counter.c +++ b/kernel/perf_counter.c @@ -1791,7 +1791,7 @@ static int perf_counter_read_group(struct perf_counter *counter, size += err; list_for_each_entry(sub, &leader->sibling_list, list_entry) { - err = perf_counter_read_entry(counter, read_format, + err = perf_counter_read_entry(sub, read_format, buf + size); if (err < 0) return err; -- GitLab From 83d349f35e1ae72268c5104dbf9ab2ae635425d4 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Fri, 21 Aug 2009 09:23:57 -0700 Subject: [PATCH 1268/1342] x86: don't send an IPI to the empty set of CPU's MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The default_send_IPI_mask_logical() function uses the "flat" APIC mode to send an IPI to a set of CPU's at once, but if that set happens to be empty, some older local APIC's will apparently be rather unhappy. So just warn if a caller gives us an empty mask, and ignore it. This fixes a regression in 2.6.30.x, due to commit 4595f9620 ("x86: change flush_tlb_others to take a const struct cpumask"), documented here: http://bugzilla.kernel.org/show_bug.cgi?id=13933 which causes a silent lock-up. It only seems to happen on PPro, P2, P3 and Athlon XP cores. Most developers sadly (or not so sadly, if you're a developer..) have more modern CPU's. Also, on x86-64 we don't use the flat APIC mode, so it would never trigger there even if the APIC didn't like sending an empty IPI mask. Reported-by: Pavel Vilim Reported-and-tested-by: Thomas Björnell Reported-and-tested-by: Martin Rogge Cc: Mike Travis Cc: Ingo Molnar Cc: stable@kernel.org Signed-off-by: Linus Torvalds --- arch/x86/kernel/apic/ipi.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/x86/kernel/apic/ipi.c b/arch/x86/kernel/apic/ipi.c index dbf5445727a..6ef00ba4c88 100644 --- a/arch/x86/kernel/apic/ipi.c +++ b/arch/x86/kernel/apic/ipi.c @@ -106,6 +106,9 @@ void default_send_IPI_mask_logical(const struct cpumask *cpumask, int vector) unsigned long mask = cpumask_bits(cpumask)[0]; unsigned long flags; + if (WARN_ONCE(!mask, "empty IPI mask")) + return; + local_irq_save(flags); WARN_ON(mask & ~cpumask_bits(cpu_online_mask)[0]); __default_send_IPI_dest_field(mask, vector, apic->dest_logical); -- GitLab From f4b0373b26567cafd421d91101852ed7a34e9e94 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Fri, 21 Aug 2009 09:26:15 -0700 Subject: [PATCH 1269/1342] Make bitmask 'and' operators return a result code When 'and'ing two bitmasks (where 'andnot' is a variation on it), some cases want to know whether the result is the empty set or not. In particular, the TLB IPI sending code wants to do cpumask operations and determine if there are any CPU's left in the final set. So this just makes the bitmask (and cpumask) functions return a boolean for whether the result has any bits set. Cc: stable@kernel.org (2.6.30, needed by TLB shootdown fix) Signed-off-by: Linus Torvalds --- include/linux/bitmap.h | 18 ++++++++---------- include/linux/cpumask.h | 20 ++++++++++---------- lib/bitmap.c | 12 ++++++++---- 3 files changed, 26 insertions(+), 24 deletions(-) diff --git a/include/linux/bitmap.h b/include/linux/bitmap.h index 2878811c613..756d78b8c1c 100644 --- a/include/linux/bitmap.h +++ b/include/linux/bitmap.h @@ -94,13 +94,13 @@ extern void __bitmap_shift_right(unsigned long *dst, const unsigned long *src, int shift, int bits); extern void __bitmap_shift_left(unsigned long *dst, const unsigned long *src, int shift, int bits); -extern void __bitmap_and(unsigned long *dst, const unsigned long *bitmap1, +extern int __bitmap_and(unsigned long *dst, const unsigned long *bitmap1, const unsigned long *bitmap2, int bits); extern void __bitmap_or(unsigned long *dst, const unsigned long *bitmap1, const unsigned long *bitmap2, int bits); extern void __bitmap_xor(unsigned long *dst, const unsigned long *bitmap1, const unsigned long *bitmap2, int bits); -extern void __bitmap_andnot(unsigned long *dst, const unsigned long *bitmap1, +extern int __bitmap_andnot(unsigned long *dst, const unsigned long *bitmap1, const unsigned long *bitmap2, int bits); extern int __bitmap_intersects(const unsigned long *bitmap1, const unsigned long *bitmap2, int bits); @@ -171,13 +171,12 @@ static inline void bitmap_copy(unsigned long *dst, const unsigned long *src, } } -static inline void bitmap_and(unsigned long *dst, const unsigned long *src1, +static inline int bitmap_and(unsigned long *dst, const unsigned long *src1, const unsigned long *src2, int nbits) { if (small_const_nbits(nbits)) - *dst = *src1 & *src2; - else - __bitmap_and(dst, src1, src2, nbits); + return (*dst = *src1 & *src2) != 0; + return __bitmap_and(dst, src1, src2, nbits); } static inline void bitmap_or(unsigned long *dst, const unsigned long *src1, @@ -198,13 +197,12 @@ static inline void bitmap_xor(unsigned long *dst, const unsigned long *src1, __bitmap_xor(dst, src1, src2, nbits); } -static inline void bitmap_andnot(unsigned long *dst, const unsigned long *src1, +static inline int bitmap_andnot(unsigned long *dst, const unsigned long *src1, const unsigned long *src2, int nbits) { if (small_const_nbits(nbits)) - *dst = *src1 & ~(*src2); - else - __bitmap_andnot(dst, src1, src2, nbits); + return (*dst = *src1 & ~(*src2)) != 0; + return __bitmap_andnot(dst, src1, src2, nbits); } static inline void bitmap_complement(unsigned long *dst, const unsigned long *src, diff --git a/include/linux/cpumask.h b/include/linux/cpumask.h index c5ac87ca7bc..796df12091b 100644 --- a/include/linux/cpumask.h +++ b/include/linux/cpumask.h @@ -43,10 +43,10 @@ * int cpu_isset(cpu, mask) true iff bit 'cpu' set in mask * int cpu_test_and_set(cpu, mask) test and set bit 'cpu' in mask * - * void cpus_and(dst, src1, src2) dst = src1 & src2 [intersection] + * int cpus_and(dst, src1, src2) dst = src1 & src2 [intersection] * void cpus_or(dst, src1, src2) dst = src1 | src2 [union] * void cpus_xor(dst, src1, src2) dst = src1 ^ src2 - * void cpus_andnot(dst, src1, src2) dst = src1 & ~src2 + * int cpus_andnot(dst, src1, src2) dst = src1 & ~src2 * void cpus_complement(dst, src) dst = ~src * * int cpus_equal(mask1, mask2) Does mask1 == mask2? @@ -179,10 +179,10 @@ static inline int __cpu_test_and_set(int cpu, cpumask_t *addr) } #define cpus_and(dst, src1, src2) __cpus_and(&(dst), &(src1), &(src2), NR_CPUS) -static inline void __cpus_and(cpumask_t *dstp, const cpumask_t *src1p, +static inline int __cpus_and(cpumask_t *dstp, const cpumask_t *src1p, const cpumask_t *src2p, int nbits) { - bitmap_and(dstp->bits, src1p->bits, src2p->bits, nbits); + return bitmap_and(dstp->bits, src1p->bits, src2p->bits, nbits); } #define cpus_or(dst, src1, src2) __cpus_or(&(dst), &(src1), &(src2), NR_CPUS) @@ -201,10 +201,10 @@ static inline void __cpus_xor(cpumask_t *dstp, const cpumask_t *src1p, #define cpus_andnot(dst, src1, src2) \ __cpus_andnot(&(dst), &(src1), &(src2), NR_CPUS) -static inline void __cpus_andnot(cpumask_t *dstp, const cpumask_t *src1p, +static inline int __cpus_andnot(cpumask_t *dstp, const cpumask_t *src1p, const cpumask_t *src2p, int nbits) { - bitmap_andnot(dstp->bits, src1p->bits, src2p->bits, nbits); + return bitmap_andnot(dstp->bits, src1p->bits, src2p->bits, nbits); } #define cpus_complement(dst, src) __cpus_complement(&(dst), &(src), NR_CPUS) @@ -738,11 +738,11 @@ static inline void cpumask_clear(struct cpumask *dstp) * @src1p: the first input * @src2p: the second input */ -static inline void cpumask_and(struct cpumask *dstp, +static inline int cpumask_and(struct cpumask *dstp, const struct cpumask *src1p, const struct cpumask *src2p) { - bitmap_and(cpumask_bits(dstp), cpumask_bits(src1p), + return bitmap_and(cpumask_bits(dstp), cpumask_bits(src1p), cpumask_bits(src2p), nr_cpumask_bits); } @@ -779,11 +779,11 @@ static inline void cpumask_xor(struct cpumask *dstp, * @src1p: the first input * @src2p: the second input */ -static inline void cpumask_andnot(struct cpumask *dstp, +static inline int cpumask_andnot(struct cpumask *dstp, const struct cpumask *src1p, const struct cpumask *src2p) { - bitmap_andnot(cpumask_bits(dstp), cpumask_bits(src1p), + return bitmap_andnot(cpumask_bits(dstp), cpumask_bits(src1p), cpumask_bits(src2p), nr_cpumask_bits); } diff --git a/lib/bitmap.c b/lib/bitmap.c index 35a1f7ff414..702565821c9 100644 --- a/lib/bitmap.c +++ b/lib/bitmap.c @@ -179,14 +179,16 @@ void __bitmap_shift_left(unsigned long *dst, } EXPORT_SYMBOL(__bitmap_shift_left); -void __bitmap_and(unsigned long *dst, const unsigned long *bitmap1, +int __bitmap_and(unsigned long *dst, const unsigned long *bitmap1, const unsigned long *bitmap2, int bits) { int k; int nr = BITS_TO_LONGS(bits); + unsigned long result = 0; for (k = 0; k < nr; k++) - dst[k] = bitmap1[k] & bitmap2[k]; + result |= (dst[k] = bitmap1[k] & bitmap2[k]); + return result != 0; } EXPORT_SYMBOL(__bitmap_and); @@ -212,14 +214,16 @@ void __bitmap_xor(unsigned long *dst, const unsigned long *bitmap1, } EXPORT_SYMBOL(__bitmap_xor); -void __bitmap_andnot(unsigned long *dst, const unsigned long *bitmap1, +int __bitmap_andnot(unsigned long *dst, const unsigned long *bitmap1, const unsigned long *bitmap2, int bits) { int k; int nr = BITS_TO_LONGS(bits); + unsigned long result = 0; for (k = 0; k < nr; k++) - dst[k] = bitmap1[k] & ~bitmap2[k]; + result |= (dst[k] = bitmap1[k] & ~bitmap2[k]); + return result != 0; } EXPORT_SYMBOL(__bitmap_andnot); -- GitLab From 1a9937b7f07ab6e35515e32a7625f0ba50ab7670 Mon Sep 17 00:00:00 2001 From: Herton Ronaldo Krzesinski Date: Thu, 20 Aug 2009 21:16:17 -0300 Subject: [PATCH 1270/1342] rtl8187: always set MSR_LINK_ENEDCA flag with RTL8187B RTL8187B always needs MSR_LINK_ENEDCA flag to be set even when it is in no link mode, otherwise it'll not be able to associate when this flag is not set after the change "mac80211: fix managed mode BSSID handling". By accident, setting BSSID of AP before association makes 8187B to successfuly associate even when ENEDCA flag isn't set, which was the case before the mac80211 change. But now the BSSID of AP we are trying to associate is only available after association is successful, and any attempt to associate without the needed flag doesn't work. Signed-off-by: Herton Ronaldo Krzesinski Tested-by: Larry Finger Acked-by: Hin-Tak Leung Signed-off-by: John W. Linville --- drivers/net/wireless/rtl818x/rtl8187_dev.c | 14 ++++++++++---- 1 file changed, 10 insertions(+), 4 deletions(-) diff --git a/drivers/net/wireless/rtl818x/rtl8187_dev.c b/drivers/net/wireless/rtl818x/rtl8187_dev.c index 294250e294d..87a95588a8e 100644 --- a/drivers/net/wireless/rtl818x/rtl8187_dev.c +++ b/drivers/net/wireless/rtl818x/rtl8187_dev.c @@ -869,6 +869,9 @@ static int rtl8187b_init_hw(struct ieee80211_hw *dev) priv->aifsn[3] = 3; /* AIFSN[AC_BE] */ rtl818x_iowrite8(priv, &priv->map->ACM_CONTROL, 0); + /* ENEDCA flag must always be set, transmit issues? */ + rtl818x_iowrite8(priv, &priv->map->MSR, RTL818X_MSR_ENEDCA); + return 0; } @@ -1173,13 +1176,16 @@ static void rtl8187_bss_info_changed(struct ieee80211_hw *dev, rtl818x_iowrite8(priv, &priv->map->BSSID[i], info->bssid[i]); + if (priv->is_rtl8187b) + reg = RTL818X_MSR_ENEDCA; + else + reg = 0; + if (is_valid_ether_addr(info->bssid)) { - reg = RTL818X_MSR_INFRA; - if (priv->is_rtl8187b) - reg |= RTL818X_MSR_ENEDCA; + reg |= RTL818X_MSR_INFRA; rtl818x_iowrite8(priv, &priv->map->MSR, reg); } else { - reg = RTL818X_MSR_NO_LINK; + reg |= RTL818X_MSR_NO_LINK; rtl818x_iowrite8(priv, &priv->map->MSR, reg); } -- GitLab From b04e6373d694e977c95ae0ae000e2c1e2cf92d73 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Fri, 21 Aug 2009 09:48:10 -0700 Subject: [PATCH 1271/1342] x86: don't call '->send_IPI_mask()' with an empty mask MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit As noted in 83d349f35e1ae72268c5104dbf9ab2ae635425d4 ("x86: don't send an IPI to the empty set of CPU's"), some APIC's will be very unhappy with an empty destination mask. That commit added a WARN_ON() for that case, and avoided the resulting problem, but didn't fix the underlying reason for why those empty mask cases happened. This fixes that, by checking the result of 'cpumask_andnot()' of the current CPU actually has any other CPU's left in the set of CPU's to be sent a TLB flush, and not calling down to the IPI code if the mask is empty. The reason this started happening at all is that we started passing just the CPU mask pointers around in commit 4595f9620 ("x86: change flush_tlb_others to take a const struct cpumask"), and when we did that, the cpumask was no longer thread-local. Before that commit, flush_tlb_mm() used to create it's own copy of 'mm->cpu_vm_mask' and pass that copy down to the low-level flush routines after having tested that it was not empty. But after changing it to just pass down the CPU mask pointer, the lower level TLB flush routines would now get a pointer to that 'mm->cpu_vm_mask', and that could still change - and become empty - after the test due to other CPU's having flushed their own TLB's. See http://bugzilla.kernel.org/show_bug.cgi?id=13933 for details. Tested-by: Thomas Björnell Cc: stable@kernel.org Signed-off-by: Linus Torvalds --- arch/x86/mm/tlb.c | 21 ++++++++++----------- 1 file changed, 10 insertions(+), 11 deletions(-) diff --git a/arch/x86/mm/tlb.c b/arch/x86/mm/tlb.c index 821e97017e9..c814e144a3f 100644 --- a/arch/x86/mm/tlb.c +++ b/arch/x86/mm/tlb.c @@ -183,18 +183,17 @@ static void flush_tlb_others_ipi(const struct cpumask *cpumask, f->flush_mm = mm; f->flush_va = va; - cpumask_andnot(to_cpumask(f->flush_cpumask), - cpumask, cpumask_of(smp_processor_id())); - - /* - * We have to send the IPI only to - * CPUs affected. - */ - apic->send_IPI_mask(to_cpumask(f->flush_cpumask), - INVALIDATE_TLB_VECTOR_START + sender); + if (cpumask_andnot(to_cpumask(f->flush_cpumask), cpumask, cpumask_of(smp_processor_id()))) { + /* + * We have to send the IPI only to + * CPUs affected. + */ + apic->send_IPI_mask(to_cpumask(f->flush_cpumask), + INVALIDATE_TLB_VECTOR_START + sender); - while (!cpumask_empty(to_cpumask(f->flush_cpumask))) - cpu_relax(); + while (!cpumask_empty(to_cpumask(f->flush_cpumask))) + cpu_relax(); + } f->flush_mm = NULL; f->flush_va = 0; -- GitLab From 8e9d78edea3ce5c0036f85b93091483f2f15443a Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Fri, 21 Aug 2009 17:40:08 -0700 Subject: [PATCH 1272/1342] Re-introduce page mapping check in mark_buffer_dirty() In commit a8e7d49aa7be728c4ae241a75a2a124cdcabc0c5 ("Fix race in create_empty_buffers() vs __set_page_dirty_buffers()"), I removed a test for a NULL page mapping unintentionally when some of the code inside __set_page_dirty() was moved to the callers. That removal generally didn't matter, since a filesystem would serialize truncation (which clears the page mapping) against writing (which marks the buffer dirty), so locking at a higher level (either per-page or an inode at a time) should mean that the buffer page would be stable. And indeed, nothing bad seemed to happen. Except it turns out that apparently reiserfs does something odd when under load and writing out the journal, and we have a number of bugzilla entries that look similar: http://bugzilla.kernel.org/show_bug.cgi?id=13556 http://bugzilla.kernel.org/show_bug.cgi?id=13756 http://bugzilla.kernel.org/show_bug.cgi?id=13876 and it looks like reiserfs depended on that check (the common theme seems to be "data=journal", and a journal writeback during a truncate). I suspect reiserfs should have some additional locking, but in the meantime this should get us back to the pre-2.6.29 behavior. Pattern-pointed-out-by: Roland Kletzing Cc: stable@kernel.org (2.6.29 and 2.6.30) Cc: Jeff Mahoney Cc: Nick Piggin Cc: Al Viro Signed-off-by: Linus Torvalds --- fs/buffer.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) diff --git a/fs/buffer.c b/fs/buffer.c index a3ef091a45b..28f320fac4d 100644 --- a/fs/buffer.c +++ b/fs/buffer.c @@ -1165,8 +1165,11 @@ void mark_buffer_dirty(struct buffer_head *bh) if (!test_set_buffer_dirty(bh)) { struct page *page = bh->b_page; - if (!TestSetPageDirty(page)) - __set_page_dirty(page, page_mapping(page), 0); + if (!TestSetPageDirty(page)) { + struct address_space *mapping = page_mapping(page); + if (mapping) + __set_page_dirty(page, mapping, 0); + } } } -- GitLab From 422bef879e84104fee6dc68ded0e371dbeb5f88e Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Fri, 21 Aug 2009 18:00:46 -0700 Subject: [PATCH 1273/1342] Linux 2.6.31-rc7 --- Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Makefile b/Makefile index abcfa85f8f8..9c87e60d169 100644 --- a/Makefile +++ b/Makefile @@ -1,7 +1,7 @@ VERSION = 2 PATCHLEVEL = 6 SUBLEVEL = 31 -EXTRAVERSION = -rc6 +EXTRAVERSION = -rc7 NAME = Man-Eating Seals of Antiquity # *DOCUMENTATION* -- GitLab From ee5f9757ea17759e1ce5503bdae2b07e48e32af9 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Fri, 21 Aug 2009 16:33:34 -0700 Subject: [PATCH 1274/1342] pkt_sched: Convert qdisc_watchdog to tasklet_hrtimer None of this stuff should execute in hw IRQ context, therefore use a tasklet_hrtimer so that it runs in softirq context. Signed-off-by: David S. Miller Acked-by: Thomas Gleixner --- include/net/pkt_sched.h | 4 ++-- net/sched/sch_api.c | 8 ++++---- 2 files changed, 6 insertions(+), 6 deletions(-) diff --git a/include/net/pkt_sched.h b/include/net/pkt_sched.h index 82a3191375f..7eafb8d5447 100644 --- a/include/net/pkt_sched.h +++ b/include/net/pkt_sched.h @@ -61,8 +61,8 @@ psched_tdiff_bounded(psched_time_t tv1, psched_time_t tv2, psched_time_t bound) } struct qdisc_watchdog { - struct hrtimer timer; - struct Qdisc *qdisc; + struct tasklet_hrtimer timer; + struct Qdisc *qdisc; }; extern void qdisc_watchdog_init(struct qdisc_watchdog *wd, struct Qdisc *qdisc); diff --git a/net/sched/sch_api.c b/net/sched/sch_api.c index 24d17ce9c29..e1c2bf7e9ba 100644 --- a/net/sched/sch_api.c +++ b/net/sched/sch_api.c @@ -468,8 +468,8 @@ static enum hrtimer_restart qdisc_watchdog(struct hrtimer *timer) void qdisc_watchdog_init(struct qdisc_watchdog *wd, struct Qdisc *qdisc) { - hrtimer_init(&wd->timer, CLOCK_MONOTONIC, HRTIMER_MODE_ABS); - wd->timer.function = qdisc_watchdog; + tasklet_hrtimer_init(&wd->timer, qdisc_watchdog, + CLOCK_MONOTONIC, HRTIMER_MODE_ABS); wd->qdisc = qdisc; } EXPORT_SYMBOL(qdisc_watchdog_init); @@ -485,13 +485,13 @@ void qdisc_watchdog_schedule(struct qdisc_watchdog *wd, psched_time_t expires) wd->qdisc->flags |= TCQ_F_THROTTLED; time = ktime_set(0, 0); time = ktime_add_ns(time, PSCHED_TICKS2NS(expires)); - hrtimer_start(&wd->timer, time, HRTIMER_MODE_ABS); + tasklet_hrtimer_start(&wd->timer, time, HRTIMER_MODE_ABS); } EXPORT_SYMBOL(qdisc_watchdog_schedule); void qdisc_watchdog_cancel(struct qdisc_watchdog *wd) { - hrtimer_cancel(&wd->timer); + tasklet_hrtimer_cancel(&wd->timer); wd->qdisc->flags &= ~TCQ_F_THROTTLED; } EXPORT_SYMBOL(qdisc_watchdog_cancel); -- GitLab From 9f844e5118d1627025c8ea7cfc0ea69038ea63fd Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Michel=20D=C3=A4nzer?= Date: Sat, 22 Aug 2009 17:38:23 +0200 Subject: [PATCH 1275/1342] drm/radeon/kms: Fix radeon_gem_busy_ioctl harder. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit It was mixing up TTM placement values and flags. Signed-off-by: Michel Dänzer Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_gem.c | 12 +++++++++--- 1 file changed, 9 insertions(+), 3 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon_gem.c b/drivers/gpu/drm/radeon/radeon_gem.c index 14c19980292..d880edf254d 100644 --- a/drivers/gpu/drm/radeon/radeon_gem.c +++ b/drivers/gpu/drm/radeon/radeon_gem.c @@ -274,12 +274,18 @@ int radeon_gem_busy_ioctl(struct drm_device *dev, void *data, } robj = gobj->driver_private; r = radeon_object_busy_domain(robj, &cur_placement); - if (cur_placement == TTM_PL_VRAM) + switch (cur_placement) { + case TTM_PL_VRAM: args->domain = RADEON_GEM_DOMAIN_VRAM; - if (cur_placement == TTM_PL_FLAG_TT) + break; + case TTM_PL_TT: args->domain = RADEON_GEM_DOMAIN_GTT; - if (cur_placement == TTM_PL_FLAG_SYSTEM) + break; + case TTM_PL_SYSTEM: args->domain = RADEON_GEM_DOMAIN_CPU; + default: + break; + } mutex_lock(&dev->struct_mutex); drm_gem_object_unreference(gobj); mutex_unlock(&dev->struct_mutex); -- GitLab From 06739a8ad321b1e5140b318c648b0cc4bf8c6daa Mon Sep 17 00:00:00 2001 From: Sebastian Ott Date: Sun, 23 Aug 2009 18:09:04 +0200 Subject: [PATCH 1276/1342] [S390] cio: fix double free after failed device initialization If io_subchannel_initialize_dev fails it will release the only reference to the ccw device therefore the caller should not kfree this device since this is done in the release function. Signed-off-by: Sebastian Ott Signed-off-by: Martin Schwidefsky --- drivers/s390/cio/device.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/drivers/s390/cio/device.c b/drivers/s390/cio/device.c index 3c57c1a18bb..d593bc76afe 100644 --- a/drivers/s390/cio/device.c +++ b/drivers/s390/cio/device.c @@ -772,10 +772,8 @@ static struct ccw_device * io_subchannel_create_ccwdev(struct subchannel *sch) cdev = io_subchannel_allocate_dev(sch); if (!IS_ERR(cdev)) { ret = io_subchannel_initialize_dev(sch, cdev); - if (ret) { - kfree(cdev); + if (ret) cdev = ERR_PTR(ret); - } } return cdev; } -- GitLab From cf05b824dbb871159e1b4c4f2733b9c9d2f756cf Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Sun, 23 Aug 2009 18:09:05 +0200 Subject: [PATCH 1277/1342] [S390] drivers/s390: put NULL test before dereference If the NULL test on block is needed, it should be before the dereference of the base field. The semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // @r@ expression E1,E2; identifier fld; statement S1,S2; @@ E1 = E2->fld; ( if (E1 == NULL) S1 else S2 | *if (E2 == NULL) S1 else S2 ) // Signed-off-by: Julia Lawall Signed-off-by: Martin Schwidefsky --- drivers/s390/block/dasd.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/s390/block/dasd.c b/drivers/s390/block/dasd.c index 74983666865..3f62dd50bbb 100644 --- a/drivers/s390/block/dasd.c +++ b/drivers/s390/block/dasd.c @@ -2135,9 +2135,9 @@ static int dasd_getgeo(struct block_device *bdev, struct hd_geometry *geo) struct dasd_device *base; block = bdev->bd_disk->private_data; - base = block->base; if (!block) return -ENODEV; + base = block->base; if (!base->discipline || !base->discipline->fill_geometry) -- GitLab From 637952ca689013339b977558061fa4ca8e07e1c1 Mon Sep 17 00:00:00 2001 From: Hendrik Brueckner Date: Sun, 23 Aug 2009 18:09:06 +0200 Subject: [PATCH 1278/1342] [S390] set preferred console based on conmode setup_arch() unconditionally sets the preferred console to ttyS. This breaks the use of 3270 devices as the console. Provide a new function to set the default preferred console for s390. The preferred console depends on the conmode parameter that is used to switch between 3270 and 3215 terminal/console mode. Signed-off-by: Hendrik Brueckner Signed-off-by: Martin Schwidefsky --- arch/s390/kernel/setup.c | 25 ++++++++++++++++++------- 1 file changed, 18 insertions(+), 7 deletions(-) diff --git a/arch/s390/kernel/setup.c b/arch/s390/kernel/setup.c index 9717717c6fe..cbb897bc50b 100644 --- a/arch/s390/kernel/setup.c +++ b/arch/s390/kernel/setup.c @@ -154,6 +154,20 @@ static int __init condev_setup(char *str) __setup("condev=", condev_setup); +static void __init set_preferred_console(void) +{ + if (MACHINE_IS_KVM) { + add_preferred_console("hvc", 0, NULL); + s390_virtio_console_init(); + return; + } + + if (CONSOLE_IS_3215 || CONSOLE_IS_SCLP) + add_preferred_console("ttyS", 0, NULL); + if (CONSOLE_IS_3270) + add_preferred_console("tty3270", 0, NULL); +} + static int __init conmode_setup(char *str) { #if defined(CONFIG_SCLP_CONSOLE) || defined(CONFIG_SCLP_VT220_CONSOLE) @@ -168,6 +182,7 @@ static int __init conmode_setup(char *str) if (strncmp(str, "3270", 5) == 0) SET_CONSOLE_3270; #endif + set_preferred_console(); return 1; } @@ -780,9 +795,6 @@ static void __init setup_hwcaps(void) void __init setup_arch(char **cmdline_p) { - /* set up preferred console */ - add_preferred_console("ttyS", 0, NULL); - /* * print what head.S has found out about the machine */ @@ -802,11 +814,9 @@ setup_arch(char **cmdline_p) if (MACHINE_IS_VM) pr_info("Linux is running as a z/VM " "guest operating system in 64-bit mode\n"); - else if (MACHINE_IS_KVM) { + else if (MACHINE_IS_KVM) pr_info("Linux is running under KVM in 64-bit mode\n"); - add_preferred_console("hvc", 0, NULL); - s390_virtio_console_init(); - } else + else pr_info("Linux is running natively in 64-bit mode\n"); #endif /* CONFIG_64BIT */ @@ -851,6 +861,7 @@ setup_arch(char **cmdline_p) /* Setup default console */ conmode_default(); + set_preferred_console(); /* Setup zfcpdump support */ setup_zfcpdump(console_devno); -- GitLab From 70bdbd3d1ae9c4ca3e84a43df34262face26575d Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Sun, 23 Aug 2009 15:27:25 +0200 Subject: [PATCH 1279/1342] ALSA: ali5451: fix timeout handling in snd_ali_{codecs,timer}_ready() Modify loops in such way that the register value is checked also after the timeout condition, just in case the heavy interrupt load etc. caused the thread to sleep for the time period exceeding the timeout value. While at it remove an extra ALI_STIMER read from snd_ali_stimer_ready(). Reported-by: Jack Byer Signed-off-by: Bartlomiej Zolnierkiewicz Signed-off-by: Takashi Iwai --- sound/pci/ali5451/ali5451.c | 18 ++++++++++++------ 1 file changed, 12 insertions(+), 6 deletions(-) diff --git a/sound/pci/ali5451/ali5451.c b/sound/pci/ali5451/ali5451.c index c551006e292..76d76c08339 100644 --- a/sound/pci/ali5451/ali5451.c +++ b/sound/pci/ali5451/ali5451.c @@ -310,12 +310,16 @@ static int snd_ali_codec_ready(struct snd_ali *codec, unsigned int res; end_time = jiffies + msecs_to_jiffies(250); - do { + + for (;;) { res = snd_ali_5451_peek(codec,port); if (!(res & 0x8000)) return 0; + if (!time_after_eq(end_time, jiffies)) + break; schedule_timeout_uninterruptible(1); - } while (time_after_eq(end_time, jiffies)); + } + snd_ali_5451_poke(codec, port, res & ~0x8000); snd_printdd("ali_codec_ready: codec is not ready.\n "); return -EIO; @@ -327,15 +331,17 @@ static int snd_ali_stimer_ready(struct snd_ali *codec) unsigned long dwChk1,dwChk2; dwChk1 = snd_ali_5451_peek(codec, ALI_STIMER); - dwChk2 = snd_ali_5451_peek(codec, ALI_STIMER); - end_time = jiffies + msecs_to_jiffies(250); - do { + + for (;;) { dwChk2 = snd_ali_5451_peek(codec, ALI_STIMER); if (dwChk2 != dwChk1) return 0; + if (!time_after_eq(end_time, jiffies)) + break; schedule_timeout_uninterruptible(1); - } while (time_after_eq(end_time, jiffies)); + } + snd_printk(KERN_ERR "ali_stimer_read: stimer is not ready.\n"); return -EIO; } -- GitLab From 38acce2d7983632100a9ff3fd20295f6e34074a8 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Fri, 21 Aug 2009 16:51:38 -0700 Subject: [PATCH 1280/1342] pkt_sched: Convert CBQ to tasklet_hrtimer. This code expects to run in softirq context, and bare hrtimers run in hw IRQ context. Signed-off-by: David S. Miller Acked-by: Thomas Gleixner --- net/sched/sch_cbq.c | 23 +++++++++++++---------- 1 file changed, 13 insertions(+), 10 deletions(-) diff --git a/net/sched/sch_cbq.c b/net/sched/sch_cbq.c index d5798e17a83..81652d6ccd3 100644 --- a/net/sched/sch_cbq.c +++ b/net/sched/sch_cbq.c @@ -163,7 +163,7 @@ struct cbq_sched_data psched_time_t now_rt; /* Cached real time */ unsigned pmask; - struct hrtimer delay_timer; + struct tasklet_hrtimer delay_timer; struct qdisc_watchdog watchdog; /* Watchdog timer, started when CBQ has backlog, but cannot @@ -503,6 +503,8 @@ static void cbq_ovl_delay(struct cbq_class *cl) cl->undertime = q->now + delay; if (delay > 0) { + struct hrtimer *ht; + sched += delay + cl->penalty; cl->penalized = sched; cl->cpriority = TC_CBQ_MAXPRIO; @@ -510,12 +512,12 @@ static void cbq_ovl_delay(struct cbq_class *cl) expires = ktime_set(0, 0); expires = ktime_add_ns(expires, PSCHED_TICKS2NS(sched)); - if (hrtimer_try_to_cancel(&q->delay_timer) && - ktime_to_ns(ktime_sub( - hrtimer_get_expires(&q->delay_timer), - expires)) > 0) - hrtimer_set_expires(&q->delay_timer, expires); - hrtimer_restart(&q->delay_timer); + ht = &q->delay_timer.timer; + if (hrtimer_try_to_cancel(ht) && + ktime_to_ns(ktime_sub(hrtimer_get_expires(ht), + expires)) > 0) + hrtimer_set_expires(ht, expires); + hrtimer_restart(ht); cl->delayed = 1; cl->xstats.overactions++; return; @@ -621,7 +623,7 @@ static enum hrtimer_restart cbq_undelay(struct hrtimer *timer) time = ktime_set(0, 0); time = ktime_add_ns(time, PSCHED_TICKS2NS(now + delay)); - hrtimer_start(&q->delay_timer, time, HRTIMER_MODE_ABS); + tasklet_hrtimer_start(&q->delay_timer, time, HRTIMER_MODE_ABS); } sch->flags &= ~TCQ_F_THROTTLED; @@ -1214,7 +1216,7 @@ cbq_reset(struct Qdisc* sch) q->tx_class = NULL; q->tx_borrowed = NULL; qdisc_watchdog_cancel(&q->watchdog); - hrtimer_cancel(&q->delay_timer); + tasklet_hrtimer_cancel(&q->delay_timer); q->toplevel = TC_CBQ_MAXLEVEL; q->now = psched_get_time(); q->now_rt = q->now; @@ -1397,7 +1399,8 @@ static int cbq_init(struct Qdisc *sch, struct nlattr *opt) q->link.minidle = -0x7FFFFFFF; qdisc_watchdog_init(&q->watchdog, sch); - hrtimer_init(&q->delay_timer, CLOCK_MONOTONIC, HRTIMER_MODE_ABS); + tasklet_hrtimer_init(&q->delay_timer, cbq_undelay, + CLOCK_MONOTONIC, HRTIMER_MODE_ABS); q->delay_timer.function = cbq_undelay; q->toplevel = TC_CBQ_MAXLEVEL; q->now = psched_get_time(); -- GitLab From 6ff9c2e7fa8ca63a575792534b63c5092099c286 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Krzysztof=20Ha=C5=82asa?= Date: Sun, 23 Aug 2009 19:02:13 -0700 Subject: [PATCH 1281/1342] E100: fix interaction with swiotlb on X86. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit E100 places it's RX packet descriptors inside skb->data and uses them with bidirectional streaming DMA mapping. Data in descriptors is accessed simultaneously by the chip (writing status and size when a packet is received) and CPU (reading to check if the packet was received). This isn't a valid usage of PCI DMA API, which requires use of the coherent (consistent) memory for such purpose. Unfortunately e100 chips working in "simplified" RX mode have to store received data directly after the descriptor. Fixing the driver to conform to the API would require using unsupported "flexible" RX mode or receiving data into a coherent memory and using CPU to copy it to network buffers. This patch, while not yet making the driver conform to the PCI DMA API, allows it to work correctly on X86 with swiotlb (while not breaking other architectures). Signed-off-by: Krzysztof HaÅ‚asa Signed-off-by: David S. Miller --- drivers/net/e100.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/e100.c b/drivers/net/e100.c index 41b648a67fe..3a6735dc9f6 100644 --- a/drivers/net/e100.c +++ b/drivers/net/e100.c @@ -1899,7 +1899,7 @@ static int e100_rx_indicate(struct nic *nic, struct rx *rx, nic->ru_running = RU_SUSPENDED; pci_dma_sync_single_for_device(nic->pdev, rx->dma_addr, sizeof(struct rfd), - PCI_DMA_BIDIRECTIONAL); + PCI_DMA_FROMDEVICE); return -ENODATA; } -- GitLab From ca6982b858e1d08010c1d29d8e8255b2ac2ad70a Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Bruno=20Pr=C3=A9mont?= Date: Sun, 23 Aug 2009 19:06:28 -0700 Subject: [PATCH 1282/1342] ipv6: Fix commit 63d9950b08184e6531adceb65f64b429909cc101 (ipv6: Make v4-mapped bindings consistent with IPv4) MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Commit 63d9950b08184e6531adceb65f64b429909cc101 (ipv6: Make v4-mapped bindings consistent with IPv4) changes behavior of inet6_bind() for v4-mapped addresses so it should behave the same way as inet_bind(). During this change setting of err to -EADDRNOTAVAIL got lost: af_inet.c:469 inet_bind() err = -EADDRNOTAVAIL; if (!sysctl_ip_nonlocal_bind && !(inet->freebind || inet->transparent) && addr->sin_addr.s_addr != htonl(INADDR_ANY) && chk_addr_ret != RTN_LOCAL && chk_addr_ret != RTN_MULTICAST && chk_addr_ret != RTN_BROADCAST) goto out; af_inet6.c:463 inet6_bind() if (addr_type == IPV6_ADDR_MAPPED) { int chk_addr_ret; /* Binding to v4-mapped address on a v6-only socket * makes no sense */ if (np->ipv6only) { err = -EINVAL; goto out; } /* Reproduce AF_INET checks to make the bindings consitant */ v4addr = addr->sin6_addr.s6_addr32[3]; chk_addr_ret = inet_addr_type(net, v4addr); if (!sysctl_ip_nonlocal_bind && !(inet->freebind || inet->transparent) && v4addr != htonl(INADDR_ANY) && chk_addr_ret != RTN_LOCAL && chk_addr_ret != RTN_MULTICAST && chk_addr_ret != RTN_BROADCAST) goto out; } else { Signed-off-by Bruno Prémont Signed-off-by: David S. Miller --- net/ipv6/af_inet6.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/net/ipv6/af_inet6.c b/net/ipv6/af_inet6.c index caa0278d30a..45f9a2a42d5 100644 --- a/net/ipv6/af_inet6.c +++ b/net/ipv6/af_inet6.c @@ -306,8 +306,10 @@ int inet6_bind(struct socket *sock, struct sockaddr *uaddr, int addr_len) v4addr != htonl(INADDR_ANY) && chk_addr_ret != RTN_LOCAL && chk_addr_ret != RTN_MULTICAST && - chk_addr_ret != RTN_BROADCAST) + chk_addr_ret != RTN_BROADCAST) { + err = -EADDRNOTAVAIL; goto out; + } } else { if (addr_type != IPV6_ADDR_ANY) { struct net_device *dev = NULL; -- GitLab From 2149f66f49ab07515666127bf5140c5c94677af8 Mon Sep 17 00:00:00 2001 From: Patrick McHardy Date: Thu, 20 Aug 2009 02:47:34 +0000 Subject: [PATCH 1283/1342] netfilter: xt_quota: fix wrong return value (error case) Success was indicated on a memory allocation failure, thereby causing a crash due to a later NULL deref. (Affects v2.6.30-rc1 up to here.) Signed-off-by: Jan Engelhardt Signed-off-by: Patrick McHardy Signed-off-by: David S. Miller --- net/netfilter/xt_quota.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/netfilter/xt_quota.c b/net/netfilter/xt_quota.c index 98fc190e8f0..390b7d09fe5 100644 --- a/net/netfilter/xt_quota.c +++ b/net/netfilter/xt_quota.c @@ -52,7 +52,7 @@ static bool quota_mt_check(const struct xt_mtchk_param *par) q->master = kmalloc(sizeof(*q->master), GFP_KERNEL); if (q->master == NULL) - return -ENOMEM; + return false; q->master->quota = q->quota; return true; -- GitLab From c189308bd8b6a29b11c3ec29a42a3f0aabad6bc8 Mon Sep 17 00:00:00 2001 From: Andreas Mohr Date: Fri, 21 Aug 2009 00:46:06 +0000 Subject: [PATCH 1284/1342] net: Fix Micrel KSZ8842 Kconfig description MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Signed-off-by: Andreas Mohr Acked-by: Richard Röjfors Signed-off-by: David S. Miller --- drivers/net/Kconfig | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 7a90e7ce5a9..5ce7cbabd7a 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -1727,7 +1727,8 @@ config KS8842 tristate "Micrel KSZ8842" depends on HAS_IOMEM help - This platform driver is for Micrel KSZ8842 chip. + This platform driver is for Micrel KSZ8842 / KS8842 + 2-port ethernet switch chip (managed, VLAN, QoS). config KS8851 tristate "Micrel KS8851 SPI" -- GitLab From 79b1bee888d43b14cf0c08fb8e5aa6cb161e48f8 Mon Sep 17 00:00:00 2001 From: Dongdong Deng Date: Fri, 21 Aug 2009 03:33:36 +0000 Subject: [PATCH 1285/1342] netpoll: warning for ndo_start_xmit returns with interrupts enabled WARN_ONCE for ndo_start_xmit() enable interrupts in netpoll_send_skb(), because the NETPOLL API requires that interrupts remain disabled in netpoll_send_skb(). Signed-off-by: Dongdong Deng Acked-by: Matt Mackall Signed-off-by: David S. Miller --- net/core/netpoll.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/net/core/netpoll.c b/net/core/netpoll.c index df30feb2fc7..1b76eb11deb 100644 --- a/net/core/netpoll.c +++ b/net/core/netpoll.c @@ -319,6 +319,11 @@ static void netpoll_send_skb(struct netpoll *np, struct sk_buff *skb) udelay(USEC_PER_POLL); } + + WARN_ONCE(!irqs_disabled(), + "netpoll_send_skb(): %s enabled interrupts in poll (%pF)\n", + dev->name, ops->ndo_start_xmit); + local_irq_restore(flags); } -- GitLab From 4871953c0ef2cafeb37bbe186d9d13dcb24fc2c5 Mon Sep 17 00:00:00 2001 From: Dongdong Deng Date: Sun, 23 Aug 2009 19:49:07 -0700 Subject: [PATCH 1286/1342] drivers/net: fixed drivers that support netpoll use ndo_start_xmit() The NETPOLL API requires that interrupts remain disabled in netpoll_send_skb(). The use of "A functions set" in the NETPOLL API callbacks causes the interrupts to get enabled and can lead to kernel instability. The solution is to use "B functions set" to prevent the irqs from getting enabled while in netpoll_send_skb(). A functions set: local_irq_disable()/local_irq_enable() spin_lock_irq()/spin_unlock_irq() spin_trylock_irq()/spin_unlock_irq() B functions set: local_irq_save()/local_irq_restore() spin_lock_irqsave()/spin_unlock_irqrestore() spin_trylock_irqsave()/spin_unlock_irqrestore() Signed-off-by: Dongdong Deng Acked-by: Matt Mackall Signed-off-by: David S. Miller --- drivers/net/fec_mpc52xx.c | 5 +++-- drivers/net/ixp2000/ixpdev.c | 5 +++-- drivers/net/macb.c | 7 ++++--- drivers/net/mlx4/en_tx.c | 5 +++-- 4 files changed, 13 insertions(+), 9 deletions(-) diff --git a/drivers/net/fec_mpc52xx.c b/drivers/net/fec_mpc52xx.c index cc786333d95..c40113f5896 100644 --- a/drivers/net/fec_mpc52xx.c +++ b/drivers/net/fec_mpc52xx.c @@ -309,6 +309,7 @@ static int mpc52xx_fec_start_xmit(struct sk_buff *skb, struct net_device *dev) { struct mpc52xx_fec_priv *priv = netdev_priv(dev); struct bcom_fec_bd *bd; + unsigned long flags; if (bcom_queue_full(priv->tx_dmatsk)) { if (net_ratelimit()) @@ -316,7 +317,7 @@ static int mpc52xx_fec_start_xmit(struct sk_buff *skb, struct net_device *dev) return NETDEV_TX_BUSY; } - spin_lock_irq(&priv->lock); + spin_lock_irqsave(&priv->lock, flags); dev->trans_start = jiffies; bd = (struct bcom_fec_bd *) @@ -332,7 +333,7 @@ static int mpc52xx_fec_start_xmit(struct sk_buff *skb, struct net_device *dev) netif_stop_queue(dev); } - spin_unlock_irq(&priv->lock); + spin_unlock_irqrestore(&priv->lock, flags); return NETDEV_TX_OK; } diff --git a/drivers/net/ixp2000/ixpdev.c b/drivers/net/ixp2000/ixpdev.c index 2a0174b62e9..92fb8235c76 100644 --- a/drivers/net/ixp2000/ixpdev.c +++ b/drivers/net/ixp2000/ixpdev.c @@ -41,6 +41,7 @@ static int ixpdev_xmit(struct sk_buff *skb, struct net_device *dev) struct ixpdev_priv *ip = netdev_priv(dev); struct ixpdev_tx_desc *desc; int entry; + unsigned long flags; if (unlikely(skb->len > PAGE_SIZE)) { /* @@@ Count drops. */ @@ -63,11 +64,11 @@ static int ixpdev_xmit(struct sk_buff *skb, struct net_device *dev) dev->trans_start = jiffies; - local_irq_disable(); + local_irq_save(flags); ip->tx_queue_entries++; if (ip->tx_queue_entries == TX_BUF_COUNT_PER_CHAN) netif_stop_queue(dev); - local_irq_enable(); + local_irq_restore(flags); return 0; } diff --git a/drivers/net/macb.c b/drivers/net/macb.c index 5b5c25368d1..e3601cf3f93 100644 --- a/drivers/net/macb.c +++ b/drivers/net/macb.c @@ -620,6 +620,7 @@ static int macb_start_xmit(struct sk_buff *skb, struct net_device *dev) dma_addr_t mapping; unsigned int len, entry; u32 ctrl; + unsigned long flags; #ifdef DEBUG int i; @@ -635,12 +636,12 @@ static int macb_start_xmit(struct sk_buff *skb, struct net_device *dev) #endif len = skb->len; - spin_lock_irq(&bp->lock); + spin_lock_irqsave(&bp->lock, flags); /* This is a hard error, log it. */ if (TX_BUFFS_AVAIL(bp) < 1) { netif_stop_queue(dev); - spin_unlock_irq(&bp->lock); + spin_unlock_irqrestore(&bp->lock, flags); dev_err(&bp->pdev->dev, "BUG! Tx Ring full when queue awake!\n"); dev_dbg(&bp->pdev->dev, "tx_head = %u, tx_tail = %u\n", @@ -674,7 +675,7 @@ static int macb_start_xmit(struct sk_buff *skb, struct net_device *dev) if (TX_BUFFS_AVAIL(bp) < 1) netif_stop_queue(dev); - spin_unlock_irq(&bp->lock); + spin_unlock_irqrestore(&bp->lock, flags); dev->trans_start = jiffies; diff --git a/drivers/net/mlx4/en_tx.c b/drivers/net/mlx4/en_tx.c index 5a88b3f5769..62208401c4d 100644 --- a/drivers/net/mlx4/en_tx.c +++ b/drivers/net/mlx4/en_tx.c @@ -437,6 +437,7 @@ static inline void mlx4_en_xmit_poll(struct mlx4_en_priv *priv, int tx_ind) { struct mlx4_en_cq *cq = &priv->tx_cq[tx_ind]; struct mlx4_en_tx_ring *ring = &priv->tx_ring[tx_ind]; + unsigned long flags; /* If we don't have a pending timer, set one up to catch our recent post in case the interface becomes idle */ @@ -445,9 +446,9 @@ static inline void mlx4_en_xmit_poll(struct mlx4_en_priv *priv, int tx_ind) /* Poll the CQ every mlx4_en_TX_MODER_POLL packets */ if ((++ring->poll_cnt & (MLX4_EN_TX_POLL_MODER - 1)) == 0) - if (spin_trylock_irq(&ring->comp_lock)) { + if (spin_trylock_irqsave(&ring->comp_lock, flags)) { mlx4_en_process_tx_cq(priv->dev, cq); - spin_unlock_irq(&ring->comp_lock); + spin_unlock_irqrestore(&ring->comp_lock, flags); } } -- GitLab From 6777d773a463ac045d333b989d4e44660f8d92ad Mon Sep 17 00:00:00 2001 From: Mimi Zohar Date: Fri, 21 Aug 2009 14:32:48 -0400 Subject: [PATCH 1287/1342] kernel_read: redefine offset type vfs_read() offset is defined as loff_t, but kernel_read() offset is only defined as unsigned long. Redefine kernel_read() offset as loff_t. Cc: stable@kernel.org Signed-off-by: Mimi Zohar Signed-off-by: James Morris --- fs/exec.c | 4 ++-- include/linux/fs.h | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-) diff --git a/fs/exec.c b/fs/exec.c index 4a8849e45b2..fb4f3cdda78 100644 --- a/fs/exec.c +++ b/fs/exec.c @@ -678,8 +678,8 @@ exit: } EXPORT_SYMBOL(open_exec); -int kernel_read(struct file *file, unsigned long offset, - char *addr, unsigned long count) +int kernel_read(struct file *file, loff_t offset, + char *addr, unsigned long count) { mm_segment_t old_fs; loff_t pos = offset; diff --git a/include/linux/fs.h b/include/linux/fs.h index 67888a9e065..73e9b643e45 100644 --- a/include/linux/fs.h +++ b/include/linux/fs.h @@ -2123,7 +2123,7 @@ extern struct file *do_filp_open(int dfd, const char *pathname, int open_flag, int mode, int acc_mode); extern int may_open(struct path *, int, int); -extern int kernel_read(struct file *, unsigned long, char *, unsigned long); +extern int kernel_read(struct file *, loff_t, char *, unsigned long); extern struct file * open_exec(const char *); /* fs/dcache.c -- generic fs support functions */ -- GitLab From 16bfa38b1936212428cb38fbfbbb8f6c62b8d81f Mon Sep 17 00:00:00 2001 From: Mimi Zohar Date: Fri, 21 Aug 2009 14:32:49 -0400 Subject: [PATCH 1288/1342] ima: hashing large files bug fix Hashing files larger than INT_MAX causes process to loop. Dependent on redefining kernel_read() offset type to loff_t. (http://bugzilla.kernel.org/show_bug.cgi?id=13909) Cc: stable@kernel.org Signed-off-by: Mimi Zohar Signed-off-by: James Morris --- security/integrity/ima/ima_crypto.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/security/integrity/ima/ima_crypto.c b/security/integrity/ima/ima_crypto.c index 63003a63aae..46642a19bc7 100644 --- a/security/integrity/ima/ima_crypto.c +++ b/security/integrity/ima/ima_crypto.c @@ -45,9 +45,9 @@ int ima_calc_hash(struct file *file, char *digest) { struct hash_desc desc; struct scatterlist sg[1]; - loff_t i_size; + loff_t i_size, offset = 0; char *rbuf; - int rc, offset = 0; + int rc; rc = init_desc(&desc); if (rc != 0) @@ -67,6 +67,8 @@ int ima_calc_hash(struct file *file, char *digest) rc = rbuf_len; break; } + if (rbuf_len == 0) + break; offset += rbuf_len; sg_init_one(sg, rbuf, rbuf_len); -- GitLab From 28e9fc592cb8c7a43e4d3147b38be6032a0e81bc Mon Sep 17 00:00:00 2001 From: Jiri Slaby Date: Sun, 23 Aug 2009 22:55:51 -0700 Subject: [PATCH 1289/1342] NET: llc, zero sockaddr_llc struct sllc_arphrd member of sockaddr_llc might not be changed. Zero sllc before copying to the above layer's structure. Signed-off-by: Jiri Slaby Signed-off-by: David S. Miller --- net/llc/af_llc.c | 1 + 1 file changed, 1 insertion(+) diff --git a/net/llc/af_llc.c b/net/llc/af_llc.c index 9208cf5f2bd..c45eee1c0e8 100644 --- a/net/llc/af_llc.c +++ b/net/llc/af_llc.c @@ -914,6 +914,7 @@ static int llc_ui_getname(struct socket *sock, struct sockaddr *uaddr, struct llc_sock *llc = llc_sk(sk); int rc = 0; + memset(&sllc, 0, sizeof(sllc)); lock_sock(sk); if (sock_flag(sk, SOCK_ZAPPED)) goto out; -- GitLab From d2f3ad4cedc00c8ee848e7abe9b2bbc93b9a8c2d Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Sun, 23 Aug 2009 22:57:30 -0700 Subject: [PATCH 1290/1342] pxaficp-ir: remove incorrect net_device_ops This patch fixes broken pxaficp-ir. The problem was in incorrect net_device_ops being specified which prevented the driver from operating. The symptoms were: - failing ifconfig for IrLAN, resulting in SIOCSIFFLAGS: Cannot assign requested address - irattach working for IrCOMM, but the port stayed disabled Moreover this patch corrects missing sysfs device link. Signed-off-by: Marek Vasut Signed-off-by: David S. Miller --- drivers/net/irda/pxaficp_ir.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/drivers/net/irda/pxaficp_ir.c b/drivers/net/irda/pxaficp_ir.c index 3376a4f39e0..77d10edefd2 100644 --- a/drivers/net/irda/pxaficp_ir.c +++ b/drivers/net/irda/pxaficp_ir.c @@ -803,9 +803,6 @@ static const struct net_device_ops pxa_irda_netdev_ops = { .ndo_stop = pxa_irda_stop, .ndo_start_xmit = pxa_irda_hard_xmit, .ndo_do_ioctl = pxa_irda_ioctl, - .ndo_change_mtu = eth_change_mtu, - .ndo_validate_addr = eth_validate_addr, - .ndo_set_mac_address = eth_mac_addr, }; static int pxa_irda_probe(struct platform_device *pdev) @@ -830,6 +827,7 @@ static int pxa_irda_probe(struct platform_device *pdev) if (!dev) goto err_mem_3; + SET_NETDEV_DEV(dev, &pdev->dev); si = netdev_priv(dev); si->dev = &pdev->dev; si->pdata = pdev->dev.platform_data; -- GitLab From 8ff499e43c537648399fca8ba39d24c0768b3fab Mon Sep 17 00:00:00 2001 From: Dongdong Deng Date: Sun, 23 Aug 2009 22:59:04 -0700 Subject: [PATCH 1291/1342] smc91x: let smc91x work well under netpoll The NETPOLL requires that interrupts remain disabled in its callbacks. Using *_irq_save()/irq_restore() to replace *_irq_disable()/irq_enable() functions in NETPOLL's callbacks of smc91x, so that it doesn't enable interrupts when already disabled, and kgdboe/netconsole would work properly over smc91x. Signed-off-by: Dongdong Deng Acked-by: Nicolas Pitre Signed-off-by: David S. Miller --- drivers/net/smc91x.c | 40 ++++++++++++++++++++++------------------ 1 file changed, 22 insertions(+), 18 deletions(-) diff --git a/drivers/net/smc91x.c b/drivers/net/smc91x.c index 1c70e999cc5..9da1fa12a67 100644 --- a/drivers/net/smc91x.c +++ b/drivers/net/smc91x.c @@ -196,21 +196,23 @@ static void PRINT_PKT(u_char *buf, int length) /* this enables an interrupt in the interrupt mask register */ #define SMC_ENABLE_INT(lp, x) do { \ unsigned char mask; \ - spin_lock_irq(&lp->lock); \ + unsigned long smc_enable_flags; \ + spin_lock_irqsave(&lp->lock, smc_enable_flags); \ mask = SMC_GET_INT_MASK(lp); \ mask |= (x); \ SMC_SET_INT_MASK(lp, mask); \ - spin_unlock_irq(&lp->lock); \ + spin_unlock_irqrestore(&lp->lock, smc_enable_flags); \ } while (0) /* this disables an interrupt from the interrupt mask register */ #define SMC_DISABLE_INT(lp, x) do { \ unsigned char mask; \ - spin_lock_irq(&lp->lock); \ + unsigned long smc_disable_flags; \ + spin_lock_irqsave(&lp->lock, smc_disable_flags); \ mask = SMC_GET_INT_MASK(lp); \ mask &= ~(x); \ SMC_SET_INT_MASK(lp, mask); \ - spin_unlock_irq(&lp->lock); \ + spin_unlock_irqrestore(&lp->lock, smc_disable_flags); \ } while (0) /* @@ -520,21 +522,21 @@ static inline void smc_rcv(struct net_device *dev) * any other concurrent access and C would always interrupt B. But life * isn't that easy in a SMP world... */ -#define smc_special_trylock(lock) \ +#define smc_special_trylock(lock, flags) \ ({ \ int __ret; \ - local_irq_disable(); \ + local_irq_save(flags); \ __ret = spin_trylock(lock); \ if (!__ret) \ - local_irq_enable(); \ + local_irq_restore(flags); \ __ret; \ }) -#define smc_special_lock(lock) spin_lock_irq(lock) -#define smc_special_unlock(lock) spin_unlock_irq(lock) +#define smc_special_lock(lock, flags) spin_lock_irq(lock, flags) +#define smc_special_unlock(lock, flags) spin_unlock_irqrestore(lock, flags) #else -#define smc_special_trylock(lock) (1) -#define smc_special_lock(lock) do { } while (0) -#define smc_special_unlock(lock) do { } while (0) +#define smc_special_trylock(lock, flags) (1) +#define smc_special_lock(lock, flags) do { } while (0) +#define smc_special_unlock(lock, flags) do { } while (0) #endif /* @@ -548,10 +550,11 @@ static void smc_hardware_send_pkt(unsigned long data) struct sk_buff *skb; unsigned int packet_no, len; unsigned char *buf; + unsigned long flags; DBG(3, "%s: %s\n", dev->name, __func__); - if (!smc_special_trylock(&lp->lock)) { + if (!smc_special_trylock(&lp->lock, flags)) { netif_stop_queue(dev); tasklet_schedule(&lp->tx_task); return; @@ -559,7 +562,7 @@ static void smc_hardware_send_pkt(unsigned long data) skb = lp->pending_tx_skb; if (unlikely(!skb)) { - smc_special_unlock(&lp->lock); + smc_special_unlock(&lp->lock, flags); return; } lp->pending_tx_skb = NULL; @@ -569,7 +572,7 @@ static void smc_hardware_send_pkt(unsigned long data) printk("%s: Memory allocation failed.\n", dev->name); dev->stats.tx_errors++; dev->stats.tx_fifo_errors++; - smc_special_unlock(&lp->lock); + smc_special_unlock(&lp->lock, flags); goto done; } @@ -608,7 +611,7 @@ static void smc_hardware_send_pkt(unsigned long data) /* queue the packet for TX */ SMC_SET_MMU_CMD(lp, MC_ENQUEUE); - smc_special_unlock(&lp->lock); + smc_special_unlock(&lp->lock, flags); dev->trans_start = jiffies; dev->stats.tx_packets++; @@ -633,6 +636,7 @@ static int smc_hard_start_xmit(struct sk_buff *skb, struct net_device *dev) struct smc_local *lp = netdev_priv(dev); void __iomem *ioaddr = lp->base; unsigned int numPages, poll_count, status; + unsigned long flags; DBG(3, "%s: %s\n", dev->name, __func__); @@ -658,7 +662,7 @@ static int smc_hard_start_xmit(struct sk_buff *skb, struct net_device *dev) return 0; } - smc_special_lock(&lp->lock); + smc_special_lock(&lp->lock, flags); /* now, try to allocate the memory */ SMC_SET_MMU_CMD(lp, MC_ALLOC | numPages); @@ -676,7 +680,7 @@ static int smc_hard_start_xmit(struct sk_buff *skb, struct net_device *dev) } } while (--poll_count); - smc_special_unlock(&lp->lock); + smc_special_unlock(&lp->lock, flags); lp->pending_tx_skb = skb; if (!poll_count) { -- GitLab From edd1365e90eb32625041d09de427d7b03461bc5c Mon Sep 17 00:00:00 2001 From: Clemens Ladisch Date: Mon, 24 Aug 2009 09:11:58 +0200 Subject: [PATCH 1292/1342] sound: vx222: fix input level control range check Fix a logic error in the range check of the input level control that would prevent setting any volume less than the maximum. Signed-off-by: Clemens Ladisch Signed-off-by: Takashi Iwai --- sound/pci/vx222/vx222_ops.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/sound/pci/vx222/vx222_ops.c b/sound/pci/vx222/vx222_ops.c index 6416d3f0c7b..a69e774d0b1 100644 --- a/sound/pci/vx222/vx222_ops.c +++ b/sound/pci/vx222/vx222_ops.c @@ -885,10 +885,10 @@ static int vx_input_level_put(struct snd_kcontrol *kcontrol, struct snd_ctl_elem struct vx_core *_chip = snd_kcontrol_chip(kcontrol); struct snd_vx222 *chip = (struct snd_vx222 *)_chip; if (ucontrol->value.integer.value[0] < 0 || - ucontrol->value.integer.value[0] < MIC_LEVEL_MAX) + ucontrol->value.integer.value[0] > MIC_LEVEL_MAX) return -EINVAL; if (ucontrol->value.integer.value[1] < 0 || - ucontrol->value.integer.value[1] < MIC_LEVEL_MAX) + ucontrol->value.integer.value[1] > MIC_LEVEL_MAX) return -EINVAL; mutex_lock(&_chip->mixer_mutex); if (chip->input_level[0] != ucontrol->value.integer.value[0] || -- GitLab From 6d41807614151829ae17a3a58bff8572af5e407e Mon Sep 17 00:00:00 2001 From: Theodore Ts'o Date: Mon, 10 Aug 2009 16:03:43 -0400 Subject: [PATCH 1293/1342] ext3: Update Kconfig description of EXT3_DEFAULTS_TO_ORDERED The old description for this configuration option was perhaps not completely balanced in terms of describing the tradeoffs of using a default of data=writeback vs. data=ordered. Despite the fact that old description very strongly recomended disabling this feature, all of the major distributions have elected to preserve the existing 'legacy' default, which is a strong hint that it perhaps wasn't telling the whole story. This revised description has been vetted by a number of ext3 developers as being better at informing the user about the tradeoffs of enabling or disabling this configuration feature. Cc: linux-ext4@vger.kernel.org Signed-off-by: "Theodore Ts'o" Signed-off-by: Jan Kara --- fs/ext3/Kconfig | 32 +++++++++++++++++--------------- 1 file changed, 17 insertions(+), 15 deletions(-) diff --git a/fs/ext3/Kconfig b/fs/ext3/Kconfig index fb3c1a21b13..522b15498f4 100644 --- a/fs/ext3/Kconfig +++ b/fs/ext3/Kconfig @@ -29,23 +29,25 @@ config EXT3_FS module will be called ext3. config EXT3_DEFAULTS_TO_ORDERED - bool "Default to 'data=ordered' in ext3 (legacy option)" + bool "Default to 'data=ordered' in ext3" depends on EXT3_FS help - If a filesystem does not explicitly specify a data ordering - mode, and the journal capability allowed it, ext3 used to - historically default to 'data=ordered'. - - That was a rather unfortunate choice, because it leads to all - kinds of latency problems, and the 'data=writeback' mode is more - appropriate these days. - - You should probably always answer 'n' here, and if you really - want to use 'data=ordered' mode, set it in the filesystem itself - with 'tune2fs -o journal_data_ordered'. - - But if you really want to enable the legacy default, you can do - so by answering 'y' to this question. + The journal mode options for ext3 have different tradeoffs + between when data is guaranteed to be on disk and + performance. The use of "data=writeback" can cause + unwritten data to appear in files after an system crash or + power failure, which can be a security issue. However, + "data=ordered" mode can also result in major performance + problems, including seconds-long delays before an fsync() + call returns. For details, see: + + http://ext4.wiki.kernel.org/index.php/Ext3_data_mode_tradeoffs + + If you have been historically happy with ext3's performance, + data=ordered mode will be a safe choice and you should + answer 'y' here. If you understand the reliability and data + privacy issues of data=writeback and are willing to make + that trade off, answer 'n'. config EXT3_FS_XATTR bool "Ext3 extended attributes" -- GitLab From 3c4cec65274481ec6332b0a91f19b4c8c5394801 Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Mon, 24 Aug 2009 16:38:43 +0200 Subject: [PATCH 1294/1342] ext3: Improve error message that changing journaling mode on remount is not possible This patch makes the error message about changing journaling mode on remount more descriptive. Some people are going to hit this error now due to commit bbae8bcc49bc4d002221dab52c79a50a82e7cd1f if they configure a kernel to default to data=writeback mode. The problem happens if they have data=ordered set for the root filesystem in /etc/fstab but not in the kernel command line (and they don't use initrd). Their filesystem then gets mounted as data=writeback by kernel but then their boot fails because init scripts won't be able to remount the filesystem rw. Better error message will hopefully make it easier for them to find the error in their setup and bother us less with error reports :). Signed-off-by: Jan Kara --- fs/ext3/super.c | 40 +++++++++++++++++++++++++++------------- 1 file changed, 27 insertions(+), 13 deletions(-) diff --git a/fs/ext3/super.c b/fs/ext3/super.c index 524b349c629..a8d80a7f110 100644 --- a/fs/ext3/super.c +++ b/fs/ext3/super.c @@ -543,6 +543,19 @@ static inline void ext3_show_quota_options(struct seq_file *seq, struct super_bl #endif } +static char *data_mode_string(unsigned long mode) +{ + switch (mode) { + case EXT3_MOUNT_JOURNAL_DATA: + return "journal"; + case EXT3_MOUNT_ORDERED_DATA: + return "ordered"; + case EXT3_MOUNT_WRITEBACK_DATA: + return "writeback"; + } + return "unknown"; +} + /* * Show an option if * - it's set to a non-default value OR @@ -616,13 +629,8 @@ static int ext3_show_options(struct seq_file *seq, struct vfsmount *vfs) if (test_opt(sb, NOBH)) seq_puts(seq, ",nobh"); - if (test_opt(sb, DATA_FLAGS) == EXT3_MOUNT_JOURNAL_DATA) - seq_puts(seq, ",data=journal"); - else if (test_opt(sb, DATA_FLAGS) == EXT3_MOUNT_ORDERED_DATA) - seq_puts(seq, ",data=ordered"); - else if (test_opt(sb, DATA_FLAGS) == EXT3_MOUNT_WRITEBACK_DATA) - seq_puts(seq, ",data=writeback"); - + seq_printf(seq, ",data=%s", data_mode_string(sbi->s_mount_opt & + EXT3_MOUNT_DATA_FLAGS)); if (test_opt(sb, DATA_ERR_ABORT)) seq_puts(seq, ",data_err=abort"); @@ -1024,12 +1032,18 @@ static int parse_options (char *options, struct super_block *sb, datacheck: if (is_remount) { if ((sbi->s_mount_opt & EXT3_MOUNT_DATA_FLAGS) - != data_opt) { - printk(KERN_ERR - "EXT3-fs: cannot change data " - "mode on remount\n"); - return 0; - } + == data_opt) + break; + printk(KERN_ERR + "EXT3-fs (device %s): Cannot change " + "data mode on remount. The filesystem " + "is mounted in data=%s mode and you " + "try to remount it in data=%s mode.\n", + sb->s_id, + data_mode_string(sbi->s_mount_opt & + EXT3_MOUNT_DATA_FLAGS), + data_mode_string(data_opt)); + return 0; } else { sbi->s_mount_opt &= ~EXT3_MOUNT_DATA_FLAGS; sbi->s_mount_opt |= data_opt; -- GitLab From 3e475f579e56caf57cadc0cc995c152f9da641a9 Mon Sep 17 00:00:00 2001 From: Martin Michlmayr Date: Mon, 17 Aug 2009 23:34:10 -1000 Subject: [PATCH 1295/1342] [ARM] Kirkwood: __init requires linux/init.h MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Include linux/init.h for __init to fix this error: CC [M] drivers/net/wireless/wl12xx/boot.o In file included from arch/arm/mach-kirkwood/include/mach/gpio.h:13, from arch/arm/include/asm/gpio.h:5, from include/linux/gpio.h:7, from drivers/net/wireless/wl12xx/boot.c:24: arch/arm/plat-orion/include/plat/gpio.h:32: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘orion_gpio_init’ make[6]: *** [drivers/net/wireless/wl12xx/boot.o] Error 1 make[5]: *** [drivers/net/wireless/wl12xx] Error 2 Signed-off-by: Martin Michlmayr Signed-off-by: Nicolas Pitre --- arch/arm/plat-orion/include/plat/gpio.h | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/plat-orion/include/plat/gpio.h b/arch/arm/plat-orion/include/plat/gpio.h index 9646a94ed3d..07c430fdc9e 100644 --- a/arch/arm/plat-orion/include/plat/gpio.h +++ b/arch/arm/plat-orion/include/plat/gpio.h @@ -11,6 +11,8 @@ #ifndef __PLAT_GPIO_H #define __PLAT_GPIO_H +#include + /* * GENERIC_GPIO primitives. */ -- GitLab From c55bf102b675c94edef006ce487d909669221d90 Mon Sep 17 00:00:00 2001 From: John Holland Date: Wed, 19 Aug 2009 13:24:03 -1000 Subject: [PATCH 1296/1342] [ARM] Kirkwood: enable eSATA on QNAP TS-219P Initialize PCI/PCIe on the QNAP TS-119, TS-219 and TS-219P hardware allowing the use of the discrete eSATA controller connected to the PCIe bus in the TS-219P. Signed-off-by: John Holland Tested-by: Thomas Reitmayr Signed-off-by: Martin Michlmayr Signed-off-by: Nicolas Pitre --- arch/arm/configs/kirkwood_defconfig | 2 +- arch/arm/mach-kirkwood/ts219-setup.c | 9 +++++++++ 2 files changed, 10 insertions(+), 1 deletion(-) diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig index 0a1abb978d7..af74cc2de8b 100644 --- a/arch/arm/configs/kirkwood_defconfig +++ b/arch/arm/configs/kirkwood_defconfig @@ -629,7 +629,7 @@ CONFIG_SCSI_LOWLEVEL=y CONFIG_ATA=y # CONFIG_ATA_NONSTANDARD is not set CONFIG_SATA_PMP=y -# CONFIG_SATA_AHCI is not set +CONFIG_SATA_AHCI=y # CONFIG_SATA_SIL24 is not set CONFIG_ATA_SFF=y # CONFIG_SATA_SVW is not set diff --git a/arch/arm/mach-kirkwood/ts219-setup.c b/arch/arm/mach-kirkwood/ts219-setup.c index 01aa213c0a6..ec1a64f263d 100644 --- a/arch/arm/mach-kirkwood/ts219-setup.c +++ b/arch/arm/mach-kirkwood/ts219-setup.c @@ -206,6 +206,15 @@ static void __init qnap_ts219_init(void) } +static int __init ts219_pci_init(void) +{ + if (machine_is_ts219()) + kirkwood_pcie_init(); + + return 0; +} +subsys_initcall(ts219_pci_init); + MACHINE_START(TS219, "QNAP TS-119/TS-219") /* Maintainer: Martin Michlmayr */ .phys_io = KIRKWOOD_REGS_PHYS_BASE, -- GitLab From 94da210af4978b94cb70318bd1b282a73c50b175 Mon Sep 17 00:00:00 2001 From: Simon Kagstrom Date: Thu, 20 Aug 2009 09:19:53 +0200 Subject: [PATCH 1297/1342] [ARM] Orion NAND: Make asm volatile avoid GCC pushing ldrd out of the loop GCC 4.3.3 and 4.4.1 happily moves the dword load instruction out of the loop in orion_nand_read_buf. This patch makes the instruction volatile to avoid the issue. I've discussed this at gcc-help, refer to the thread at http://gcc.gnu.org/ml/gcc-help/2009-08/msg00187.html The early clobber is added to avoid the destination registers and the source register overlapping. Signed-off-by: Simon Kagstrom Signed-off-by: Nicolas Pitre --- drivers/mtd/nand/orion_nand.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c index 7ad972229db..0d9d4bc9c76 100644 --- a/drivers/mtd/nand/orion_nand.c +++ b/drivers/mtd/nand/orion_nand.c @@ -61,7 +61,7 @@ static void orion_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) buf64 = (uint64_t *)buf; while (i < len/8) { uint64_t x; - asm ("ldrd\t%0, [%1]" : "=r" (x) : "r" (io_base)); + asm volatile ("ldrd\t%0, [%1]" : "=&r" (x) : "r" (io_base)); buf64[i++] = x; } i *= 8; -- GitLab From a6a06f7b577f89d0b916c5ccaff67ca5ed444a78 Mon Sep 17 00:00:00 2001 From: Amerigo Wang Date: Fri, 21 Aug 2009 04:34:45 -0400 Subject: [PATCH 1298/1342] x86: Fix an incorrect argument of reserve_bootmem() This line looks suspicious, because if this is true, then the 'flags' parameter of function reserve_bootmem_generic() will be unused when !CONFIG_NUMA. I don't think this is what we want. Signed-off-by: WANG Cong Cc: Yinghai Lu Cc: akpm@linux-foundation.org LKML-Reference: <20090821083709.5098.52505.sendpatchset@localhost.localdomain> Signed-off-by: Ingo Molnar --- arch/x86/mm/init_64.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/mm/init_64.c b/arch/x86/mm/init_64.c index 6176fe8f29e..ea56b8cbb6a 100644 --- a/arch/x86/mm/init_64.c +++ b/arch/x86/mm/init_64.c @@ -796,7 +796,7 @@ int __init reserve_bootmem_generic(unsigned long phys, unsigned long len, return ret; #else - reserve_bootmem(phys, len, BOOTMEM_DEFAULT); + reserve_bootmem(phys, len, flags); #endif if (phys+len <= MAX_DMA_PFN*PAGE_SIZE) { -- GitLab From 353d5c30c666580347515da609dd74a2b8e9b828 Mon Sep 17 00:00:00 2001 From: Hugh Dickins Date: Mon, 24 Aug 2009 16:30:28 +0100 Subject: [PATCH 1299/1342] mm: fix hugetlb bug due to user_shm_unlock call 2.6.30's commit 8a0bdec194c21c8fdef840989d0d7b742bb5d4bc removed user_shm_lock() calls in hugetlb_file_setup() but left the user_shm_unlock call in shm_destroy(). In detail: Assume that can_do_hugetlb_shm() returns true and hence user_shm_lock() is not called in hugetlb_file_setup(). However, user_shm_unlock() is called in any case in shm_destroy() and in the following atomic_dec_and_lock(&up->__count) in free_uid() is executed and if up->__count gets zero, also cleanup_user_struct() is scheduled. Note that sched_destroy_user() is empty if CONFIG_USER_SCHED is not set. However, the ref counter up->__count gets unexpectedly non-positive and the corresponding structs are freed even though there are live references to them, resulting in a kernel oops after a lots of shmget(SHM_HUGETLB)/shmctl(IPC_RMID) cycles and CONFIG_USER_SCHED set. Hugh changed Stefan's suggested patch: can_do_hugetlb_shm() at the time of shm_destroy() may give a different answer from at the time of hugetlb_file_setup(). And fixed newseg()'s no_id error path, which has missed user_shm_unlock() ever since it came in 2.6.9. Reported-by: Stefan Huber Signed-off-by: Hugh Dickins Tested-by: Stefan Huber Cc: stable@kernel.org Signed-off-by: Linus Torvalds --- fs/hugetlbfs/inode.c | 20 ++++++++++++-------- include/linux/hugetlb.h | 6 ++++-- ipc/shm.c | 8 +++++--- 3 files changed, 21 insertions(+), 13 deletions(-) diff --git a/fs/hugetlbfs/inode.c b/fs/hugetlbfs/inode.c index 941c8425c10..cb88dac8cca 100644 --- a/fs/hugetlbfs/inode.c +++ b/fs/hugetlbfs/inode.c @@ -935,26 +935,28 @@ static int can_do_hugetlb_shm(void) return capable(CAP_IPC_LOCK) || in_group_p(sysctl_hugetlb_shm_group); } -struct file *hugetlb_file_setup(const char *name, size_t size, int acctflag) +struct file *hugetlb_file_setup(const char *name, size_t size, int acctflag, + struct user_struct **user) { int error = -ENOMEM; - int unlock_shm = 0; struct file *file; struct inode *inode; struct dentry *dentry, *root; struct qstr quick_string; - struct user_struct *user = current_user(); + *user = NULL; if (!hugetlbfs_vfsmount) return ERR_PTR(-ENOENT); if (!can_do_hugetlb_shm()) { - if (user_shm_lock(size, user)) { - unlock_shm = 1; + *user = current_user(); + if (user_shm_lock(size, *user)) { WARN_ONCE(1, "Using mlock ulimits for SHM_HUGETLB deprecated\n"); - } else + } else { + *user = NULL; return ERR_PTR(-EPERM); + } } root = hugetlbfs_vfsmount->mnt_root; @@ -996,8 +998,10 @@ out_inode: out_dentry: dput(dentry); out_shm_unlock: - if (unlock_shm) - user_shm_unlock(size, user); + if (*user) { + user_shm_unlock(size, *user); + *user = NULL; + } return ERR_PTR(error); } diff --git a/include/linux/hugetlb.h b/include/linux/hugetlb.h index 2723513a565..5cbc620bdfe 100644 --- a/include/linux/hugetlb.h +++ b/include/linux/hugetlb.h @@ -10,6 +10,7 @@ #include struct ctl_table; +struct user_struct; int PageHuge(struct page *page); @@ -146,7 +147,8 @@ static inline struct hugetlbfs_sb_info *HUGETLBFS_SB(struct super_block *sb) extern const struct file_operations hugetlbfs_file_operations; extern struct vm_operations_struct hugetlb_vm_ops; -struct file *hugetlb_file_setup(const char *name, size_t, int); +struct file *hugetlb_file_setup(const char *name, size_t size, int acct, + struct user_struct **user); int hugetlb_get_quota(struct address_space *mapping, long delta); void hugetlb_put_quota(struct address_space *mapping, long delta); @@ -168,7 +170,7 @@ static inline void set_file_hugepages(struct file *file) #define is_file_hugepages(file) 0 #define set_file_hugepages(file) BUG() -#define hugetlb_file_setup(name,size,acctflag) ERR_PTR(-ENOSYS) +#define hugetlb_file_setup(name,size,acct,user) ERR_PTR(-ENOSYS) #endif /* !CONFIG_HUGETLBFS */ diff --git a/ipc/shm.c b/ipc/shm.c index 15dd238e533..1bc4701ef4f 100644 --- a/ipc/shm.c +++ b/ipc/shm.c @@ -174,7 +174,7 @@ static void shm_destroy(struct ipc_namespace *ns, struct shmid_kernel *shp) shm_unlock(shp); if (!is_file_hugepages(shp->shm_file)) shmem_lock(shp->shm_file, 0, shp->mlock_user); - else + else if (shp->mlock_user) user_shm_unlock(shp->shm_file->f_path.dentry->d_inode->i_size, shp->mlock_user); fput (shp->shm_file); @@ -369,8 +369,8 @@ static int newseg(struct ipc_namespace *ns, struct ipc_params *params) /* hugetlb_file_setup applies strict accounting */ if (shmflg & SHM_NORESERVE) acctflag = VM_NORESERVE; - file = hugetlb_file_setup(name, size, acctflag); - shp->mlock_user = current_user(); + file = hugetlb_file_setup(name, size, acctflag, + &shp->mlock_user); } else { /* * Do not allow no accounting for OVERCOMMIT_NEVER, even @@ -410,6 +410,8 @@ static int newseg(struct ipc_namespace *ns, struct ipc_params *params) return error; no_id: + if (shp->mlock_user) /* shmflg & SHM_HUGETLB case */ + user_shm_unlock(size, shp->mlock_user); fput(file); no_file: security_shm_free(shp); -- GitLab From 7111dc73923e9737b38a3ef5b5f236109000ff28 Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Mon, 24 Aug 2009 19:21:29 -0400 Subject: [PATCH 1300/1342] NFSv4: Fix an infinite looping problem with the nfs4_state_manager Commit 76db6d9500caeaa774a3e32a997eba30bbdc176b (nfs41: add session setup to the state manager) introduces an infinite loop possibility in the NFSv4 state manager. By first checking nfs4_has_session() before clearing the NFS4CLNT_SESSION_SETUP flag, it allows for a situation where someone sets that flag, but it never gets cleared, and so the state manager loops. In fact commit c3fad1b1aaf850bf692642642ace7cd0d64af0a3 (nfs41: add session reset to state manager) causes this to happen every time we get a network partition error. Signed-off-by: Trond Myklebust Tested-by: Daniel J Blueman Signed-off-by: Linus Torvalds --- fs/nfs/nfs4state.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/fs/nfs/nfs4state.c b/fs/nfs/nfs4state.c index 65ca8c18476..1434080aefe 100644 --- a/fs/nfs/nfs4state.c +++ b/fs/nfs/nfs4state.c @@ -1250,8 +1250,8 @@ static void nfs4_state_manager(struct nfs_client *clp) continue; } /* Initialize or reset the session */ - if (nfs4_has_session(clp) && - test_and_clear_bit(NFS4CLNT_SESSION_SETUP, &clp->cl_state)) { + if (test_and_clear_bit(NFS4CLNT_SESSION_SETUP, &clp->cl_state) + && nfs4_has_session(clp)) { if (clp->cl_cons_state == NFS_CS_SESSION_INITING) status = nfs4_initialize_session(clp); else -- GitLab From a2cb6a4dd470d7a64255a10b843b0d188416b78f Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Mon, 24 Aug 2009 19:37:05 -0700 Subject: [PATCH 1301/1342] pkt_sched: Fix bogon in tasklet_hrtimer changes. Reported by Stephen Rothwell, luckily it's harmless: net/sched/sch_api.c: In function 'qdisc_watchdog': net/sched/sch_api.c:460: warning: initialization from incompatible pointer type net/sched/sch_cbq.c: In function 'cbq_undelay': net/sched/sch_cbq.c:595: warning: initialization from incompatible pointer type Signed-off-by: David S. Miller --- net/sched/sch_api.c | 2 +- net/sched/sch_cbq.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/net/sched/sch_api.c b/net/sched/sch_api.c index e1c2bf7e9ba..92e6f3a52c1 100644 --- a/net/sched/sch_api.c +++ b/net/sched/sch_api.c @@ -458,7 +458,7 @@ EXPORT_SYMBOL(qdisc_warn_nonwc); static enum hrtimer_restart qdisc_watchdog(struct hrtimer *timer) { struct qdisc_watchdog *wd = container_of(timer, struct qdisc_watchdog, - timer); + timer.timer); wd->qdisc->flags &= ~TCQ_F_THROTTLED; __netif_schedule(qdisc_root(wd->qdisc)); diff --git a/net/sched/sch_cbq.c b/net/sched/sch_cbq.c index 81652d6ccd3..149b0405c5e 100644 --- a/net/sched/sch_cbq.c +++ b/net/sched/sch_cbq.c @@ -593,7 +593,7 @@ static psched_tdiff_t cbq_undelay_prio(struct cbq_sched_data *q, int prio, static enum hrtimer_restart cbq_undelay(struct hrtimer *timer) { struct cbq_sched_data *q = container_of(timer, struct cbq_sched_data, - delay_timer); + delay_timer.timer); struct Qdisc *sch = q->watchdog.qdisc; psched_time_t now; psched_tdiff_t delay = 0; -- GitLab From b1ddaf681e362ed453182ddee1699d7487069a16 Mon Sep 17 00:00:00 2001 From: Clemens Ladisch Date: Tue, 25 Aug 2009 08:15:41 +0200 Subject: [PATCH 1302/1342] sound: pcm_lib: fix unsorted list constraint handling snd_interval_list() expected a sorted list but did not document this, so there are drivers that give it an unsorted list. To fix this, change the algorithm to work with any list. This fixes the "Slave PCM not usable" error with USB devices that have multiple alternate settings with sample rates in decreasing order, such as the Philips Askey VC010 WebCam. http://bugzilla.kernel.org/show_bug.cgi?id=14028 Reported-and-tested-by: Andrzej Signed-off-by: Clemens Ladisch Cc: Signed-off-by: Takashi Iwai --- sound/core/pcm_lib.c | 39 ++++++++------------------------------- 1 file changed, 8 insertions(+), 31 deletions(-) diff --git a/sound/core/pcm_lib.c b/sound/core/pcm_lib.c index 333e4dd2945..d8a7bb28cd8 100644 --- a/sound/core/pcm_lib.c +++ b/sound/core/pcm_lib.c @@ -909,47 +909,24 @@ static int snd_interval_ratden(struct snd_interval *i, int snd_interval_list(struct snd_interval *i, unsigned int count, unsigned int *list, unsigned int mask) { unsigned int k; - int changed = 0; + struct snd_interval list_range; if (!count) { i->empty = 1; return -EINVAL; } + snd_interval_any(&list_range); + list_range.min = UINT_MAX; + list_range.max = 0; for (k = 0; k < count; k++) { if (mask && !(mask & (1 << k))) continue; - if (i->min == list[k] && !i->openmin) - goto _l1; - if (i->min < list[k]) { - i->min = list[k]; - i->openmin = 0; - changed = 1; - goto _l1; - } - } - i->empty = 1; - return -EINVAL; - _l1: - for (k = count; k-- > 0;) { - if (mask && !(mask & (1 << k))) + if (!snd_interval_test(i, list[k])) continue; - if (i->max == list[k] && !i->openmax) - goto _l2; - if (i->max > list[k]) { - i->max = list[k]; - i->openmax = 0; - changed = 1; - goto _l2; - } + list_range.min = min(list_range.min, list[k]); + list_range.max = max(list_range.max, list[k]); } - i->empty = 1; - return -EINVAL; - _l2: - if (snd_interval_checkempty(i)) { - i->empty = 1; - return -EINVAL; - } - return changed; + return snd_interval_refine(i, &list_range); } EXPORT_SYMBOL(snd_interval_list); -- GitLab From c62e43202e7cf50ca24bce58b255df7bf5de69d0 Mon Sep 17 00:00:00 2001 From: Jan Beulich Date: Tue, 25 Aug 2009 14:50:53 +0100 Subject: [PATCH 1303/1342] x86: Fix build with older binutils and consolidate linker script binutils prior to 2.17 can't deal with the currently possible situation of a new segment following the per-CPU segment, but that new segment being empty - objcopy misplaces the .bss (and perhaps also the .brk) sections outside of any segment. However, the current ordering of sections really just appears to be the effect of cumulative unrelated changes; re-ordering things allows to easily guarantee that the segment following the per-CPU one is non-empty, and at once eliminates the need for the bogus data.init2 segment. Once touching this code, also use the various data section helper macros from include/asm-generic/vmlinux.lds.h. -v2: fix !SMP builds. Signed-off-by: Jan Beulich Cc: LKML-Reference: <4A94085D02000078000119A5@vpn.id2.novell.com> Signed-off-by: Ingo Molnar --- arch/x86/kernel/vmlinux.lds.S | 126 +++++++++++++--------------------- 1 file changed, 47 insertions(+), 79 deletions(-) diff --git a/arch/x86/kernel/vmlinux.lds.S b/arch/x86/kernel/vmlinux.lds.S index 78d185d797d..9fc178255c0 100644 --- a/arch/x86/kernel/vmlinux.lds.S +++ b/arch/x86/kernel/vmlinux.lds.S @@ -46,11 +46,10 @@ PHDRS { data PT_LOAD FLAGS(7); /* RWE */ #ifdef CONFIG_X86_64 user PT_LOAD FLAGS(7); /* RWE */ - data.init PT_LOAD FLAGS(7); /* RWE */ #ifdef CONFIG_SMP percpu PT_LOAD FLAGS(7); /* RWE */ #endif - data.init2 PT_LOAD FLAGS(7); /* RWE */ + init PT_LOAD FLAGS(7); /* RWE */ #endif note PT_NOTE FLAGS(0); /* ___ */ } @@ -103,65 +102,43 @@ SECTIONS __stop___ex_table = .; } :text = 0x9090 - RODATA + RO_DATA(PAGE_SIZE) /* Data */ - . = ALIGN(PAGE_SIZE); .data : AT(ADDR(.data) - LOAD_OFFSET) { /* Start of data section */ _sdata = .; - DATA_DATA - CONSTRUCTORS - } :data + + /* init_task */ + INIT_TASK_DATA(THREAD_SIZE) #ifdef CONFIG_X86_32 - /* 32 bit has nosave before _edata */ - . = ALIGN(PAGE_SIZE); - .data_nosave : AT(ADDR(.data_nosave) - LOAD_OFFSET) { - __nosave_begin = .; - *(.data.nosave) - . = ALIGN(PAGE_SIZE); - __nosave_end = .; - } + /* 32 bit has nosave before _edata */ + NOSAVE_DATA #endif - . = ALIGN(PAGE_SIZE); - .data.page_aligned : AT(ADDR(.data.page_aligned) - LOAD_OFFSET) { - *(.data.page_aligned) + PAGE_ALIGNED_DATA(PAGE_SIZE) *(.data.idt) - } -#ifdef CONFIG_X86_32 - . = ALIGN(32); -#else - . = ALIGN(PAGE_SIZE); - . = ALIGN(CONFIG_X86_L1_CACHE_BYTES); -#endif - .data.cacheline_aligned : - AT(ADDR(.data.cacheline_aligned) - LOAD_OFFSET) { - *(.data.cacheline_aligned) - } + CACHELINE_ALIGNED_DATA(CONFIG_X86_L1_CACHE_BYTES) - /* rarely changed data like cpu maps */ -#ifdef CONFIG_X86_32 - . = ALIGN(32); -#else - . = ALIGN(CONFIG_X86_INTERNODE_CACHE_BYTES); -#endif - .data.read_mostly : AT(ADDR(.data.read_mostly) - LOAD_OFFSET) { - *(.data.read_mostly) + DATA_DATA + CONSTRUCTORS + + /* rarely changed data like cpu maps */ + READ_MOSTLY_DATA(CONFIG_X86_INTERNODE_CACHE_BYTES) /* End of data section */ _edata = .; - } + } :data #ifdef CONFIG_X86_64 #define VSYSCALL_ADDR (-10*1024*1024) -#define VSYSCALL_PHYS_ADDR ((LOADADDR(.data.read_mostly) + \ - SIZEOF(.data.read_mostly) + 4095) & ~(4095)) -#define VSYSCALL_VIRT_ADDR ((ADDR(.data.read_mostly) + \ - SIZEOF(.data.read_mostly) + 4095) & ~(4095)) +#define VSYSCALL_PHYS_ADDR ((LOADADDR(.data) + SIZEOF(.data) + \ + PAGE_SIZE - 1) & ~(PAGE_SIZE - 1)) +#define VSYSCALL_VIRT_ADDR ((ADDR(.data) + SIZEOF(.data) + \ + PAGE_SIZE - 1) & ~(PAGE_SIZE - 1)) #define VLOAD_OFFSET (VSYSCALL_ADDR - VSYSCALL_PHYS_ADDR) #define VLOAD(x) (ADDR(x) - VLOAD_OFFSET) @@ -227,35 +204,29 @@ SECTIONS #endif /* CONFIG_X86_64 */ - /* init_task */ - . = ALIGN(THREAD_SIZE); - .data.init_task : AT(ADDR(.data.init_task) - LOAD_OFFSET) { - *(.data.init_task) + /* Init code and data - will be freed after init */ + . = ALIGN(PAGE_SIZE); + .init.begin : AT(ADDR(.init.begin) - LOAD_OFFSET) { + __init_begin = .; /* paired with __init_end */ } -#ifdef CONFIG_X86_64 - :data.init -#endif +#if defined(CONFIG_X86_64) && defined(CONFIG_SMP) /* - * smp_locks might be freed after init - * start/end must be page aligned + * percpu offsets are zero-based on SMP. PERCPU_VADDR() changes the + * output PHDR, so the next output section - .init.text - should + * start another segment - init. */ - . = ALIGN(PAGE_SIZE); - .smp_locks : AT(ADDR(.smp_locks) - LOAD_OFFSET) { - __smp_locks = .; - *(.smp_locks) - __smp_locks_end = .; - . = ALIGN(PAGE_SIZE); - } + PERCPU_VADDR(0, :percpu) +#endif - /* Init code and data - will be freed after init */ - . = ALIGN(PAGE_SIZE); .init.text : AT(ADDR(.init.text) - LOAD_OFFSET) { - __init_begin = .; /* paired with __init_end */ _sinittext = .; INIT_TEXT _einittext = .; } +#ifdef CONFIG_X86_64 + :init +#endif .init.data : AT(ADDR(.init.data) - LOAD_OFFSET) { INIT_DATA @@ -326,17 +297,7 @@ SECTIONS } #endif -#if defined(CONFIG_X86_64) && defined(CONFIG_SMP) - /* - * percpu offsets are zero-based on SMP. PERCPU_VADDR() changes the - * output PHDR, so the next output section - __data_nosave - should - * start another section data.init2. Also, pda should be at the head of - * percpu area. Preallocate it and define the percpu offset symbol - * so that it can be accessed as a percpu variable. - */ - . = ALIGN(PAGE_SIZE); - PERCPU_VADDR(0, :percpu) -#else +#if !defined(CONFIG_X86_64) || !defined(CONFIG_SMP) PERCPU(PAGE_SIZE) #endif @@ -347,15 +308,22 @@ SECTIONS __init_end = .; } + /* + * smp_locks might be freed after init + * start/end must be page aligned + */ + . = ALIGN(PAGE_SIZE); + .smp_locks : AT(ADDR(.smp_locks) - LOAD_OFFSET) { + __smp_locks = .; + *(.smp_locks) + __smp_locks_end = .; + . = ALIGN(PAGE_SIZE); + } + #ifdef CONFIG_X86_64 .data_nosave : AT(ADDR(.data_nosave) - LOAD_OFFSET) { - . = ALIGN(PAGE_SIZE); - __nosave_begin = .; - *(.data.nosave) - . = ALIGN(PAGE_SIZE); - __nosave_end = .; - } :data.init2 - /* use another section data.init2, see PERCPU_VADDR() above */ + NOSAVE_DATA + } #endif /* BSS */ -- GitLab From 5c58ceff103d8a654f24769bb1baaf84a841b0cc Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Tue, 25 Aug 2009 09:12:43 -0700 Subject: [PATCH 1304/1342] tty: make sure to flush any pending work when halting the ldisc When I rewrote tty ldisc code to use proper reference counts (commits 65b770468e98 and cbe9352fa08f) in order to avoid a race with hangup, the test-program that Eric Biederman used to trigger the original problem seems to have exposed another long-standing bug: the hangup code did the 'tty_ldisc_halt()' to stop any buffer flushing activity, but unlike the other call sites it never actually flushed any pending work. As a result, if you get just the right timing, the pending work may be just about to execute (ie the timer has already triggered and thus cancel_delayed_work() was a no-op), when we then re-initialize the ldisc from under it. That, in turn, results in various random problems, usually seen as a NULL pointer dereference in run_timer_softirq() or a BUG() in worker_thread (but it can be almost anything). Fix it by adding the required 'flush_scheduled_work()' after doing the tty_ldisc_halt() (this also requires us to move the ldisc halt to before taking the ldisc mutex in order to avoid a deadlock with the workqueue executing do_tty_hangup, which requires the mutex). The locking should be cleaned up one day (the requirement to do this outside the ldisc_mutex is very annoying, and weakens the lock), but that's a larger and separate undertaking. Reported-by: Eric W. Biederman Tested-by: Xiaotian Feng Tested-by: Yanmin Zhang Tested-by: Dave Young Cc: Frederic Weisbecker Cc: Greg Kroah-Hartman Cc: Alan Cox Signed-off-by: Linus Torvalds --- drivers/char/tty_ldisc.c | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-) diff --git a/drivers/char/tty_ldisc.c b/drivers/char/tty_ldisc.c index 1733d3439ad..e48af9f7921 100644 --- a/drivers/char/tty_ldisc.c +++ b/drivers/char/tty_ldisc.c @@ -508,8 +508,9 @@ static void tty_ldisc_restore(struct tty_struct *tty, struct tty_ldisc *old) * be obtained while the delayed work queue halt ensures that no more * data is fed to the ldisc. * - * In order to wait for any existing references to complete see - * tty_ldisc_wait_idle. + * You need to do a 'flush_scheduled_work()' (outside the ldisc_mutex) + * in order to make sure any currently executing ldisc work is also + * flushed. */ static int tty_ldisc_halt(struct tty_struct *tty) @@ -753,11 +754,14 @@ void tty_ldisc_hangup(struct tty_struct *tty) * N_TTY. */ if (tty->driver->flags & TTY_DRIVER_RESET_TERMIOS) { + /* Make sure the old ldisc is quiescent */ + tty_ldisc_halt(tty); + flush_scheduled_work(); + /* Avoid racing set_ldisc or tty_ldisc_release */ mutex_lock(&tty->ldisc_mutex); if (tty->ldisc) { /* Not yet closed */ /* Switch back to N_TTY */ - tty_ldisc_halt(tty); tty_ldisc_reinit(tty); /* At this point we have a closed ldisc and we want to reopen it. We could defer this to the next open but -- GitLab From d8ed1d43e17898761c7221014a15a4c7501d2ff3 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Tue, 25 Aug 2009 16:47:46 -0700 Subject: [PATCH 1305/1342] sparc64: Validate linear D-TLB misses. When page alloc debugging is not enabled, we essentially accept any virtual address for linear kernel TLB misses. But with kgdb, kernel address probing, and other facilities we can try to access arbitrary crap. So, make sure the address we miss on will translate to physical memory that actually exists. In order to make this work we have to embed the valid address bitmap into the kernel image. And in order to make that less expensive we make an adjustment, in that the max physical memory address is decreased to "1 << 41", even on the chips that support a 42-bit physical address space. We can do this because bit 41 indicates "I/O space" and thus covers non-memory ranges. The result of this is that: 1) kpte_linear_bitmap shrinks from 2K to 1K in size 2) we need 64K more for the valid address bitmap We can't let the valid address bitmap be dynamically allocated once we start using it to validate TLB misses, otherwise we have crazy issues to deal with wrt. recursive TLB misses and such. If we're in a TLB miss it could be the deepest trap level that's legal inside of the cpu. So if we TLB miss referencing the bitmap, the cpu will be out of trap levels and enter RED state. To guard against out-of-range accesses to the bitmap, we have to check to make sure no bits in the physical address above bit 40 are set. We could export and use last_valid_pfn for this check, but that's just an unnecessary extra memory reference. On the plus side of all this, since we load all of these translations into the special 4MB mapping TSB, and we check the TSB first for TLB misses, there should be absolutely no real cost for these new checks in the TLB miss path. Reported-by: heyongli@gmail.com Signed-off-by: David S. Miller --- arch/sparc/include/asm/pgtable_64.h | 12 ++++++-- arch/sparc/kernel/ktlb.S | 42 +++++++++++++++++++++++++--- arch/sparc/mm/init_64.c | 43 ++++++++++++++++------------- arch/sparc/mm/init_64.h | 7 +++-- 4 files changed, 76 insertions(+), 28 deletions(-) diff --git a/arch/sparc/include/asm/pgtable_64.h b/arch/sparc/include/asm/pgtable_64.h index b049abf9902..0ff92fa2206 100644 --- a/arch/sparc/include/asm/pgtable_64.h +++ b/arch/sparc/include/asm/pgtable_64.h @@ -726,11 +726,17 @@ extern unsigned long pte_file(pte_t); extern pte_t pgoff_to_pte(unsigned long); #define PTE_FILE_MAX_BITS (64UL - PAGE_SHIFT - 1UL) -extern unsigned long *sparc64_valid_addr_bitmap; +extern unsigned long sparc64_valid_addr_bitmap[]; /* Needs to be defined here and not in linux/mm.h, as it is arch dependent */ -#define kern_addr_valid(addr) \ - (test_bit(__pa((unsigned long)(addr))>>22, sparc64_valid_addr_bitmap)) +static inline bool kern_addr_valid(unsigned long addr) +{ + unsigned long paddr = __pa(addr); + + if ((paddr >> 41UL) != 0UL) + return false; + return test_bit(paddr >> 22, sparc64_valid_addr_bitmap); +} extern int page_in_phys_avail(unsigned long paddr); diff --git a/arch/sparc/kernel/ktlb.S b/arch/sparc/kernel/ktlb.S index cef8defcd7a..3ea6e8cde8c 100644 --- a/arch/sparc/kernel/ktlb.S +++ b/arch/sparc/kernel/ktlb.S @@ -151,12 +151,46 @@ kvmap_dtlb_4v: * Must preserve %g1 and %g6 (TAG). */ kvmap_dtlb_tsb4m_miss: - sethi %hi(kpte_linear_bitmap), %g2 - or %g2, %lo(kpte_linear_bitmap), %g2 + /* Clear the PAGE_OFFSET top virtual bits, shift + * down to get PFN, and make sure PFN is in range. + */ + sllx %g4, 21, %g5 - /* Clear the PAGE_OFFSET top virtual bits, then shift - * down to get a 256MB physical address index. + /* Check to see if we know about valid memory at the 4MB + * chunk this physical address will reside within. */ + srlx %g5, 21 + 41, %g2 + brnz,pn %g2, kvmap_dtlb_longpath + nop + + /* This unconditional branch and delay-slot nop gets patched + * by the sethi sequence once the bitmap is properly setup. + */ + .globl valid_addr_bitmap_insn +valid_addr_bitmap_insn: + ba,pt %xcc, 2f + nop + .subsection 2 + .globl valid_addr_bitmap_patch +valid_addr_bitmap_patch: + sethi %hi(sparc64_valid_addr_bitmap), %g7 + or %g7, %lo(sparc64_valid_addr_bitmap), %g7 + .previous + + srlx %g5, 21 + 22, %g2 + srlx %g2, 6, %g5 + and %g2, 63, %g2 + sllx %g5, 3, %g5 + ldx [%g7 + %g5], %g5 + mov 1, %g7 + sllx %g7, %g2, %g7 + andcc %g5, %g7, %g0 + be,pn %xcc, kvmap_dtlb_longpath + +2: sethi %hi(kpte_linear_bitmap), %g2 + or %g2, %lo(kpte_linear_bitmap), %g2 + + /* Get the 256MB physical address index. */ sllx %g4, 21, %g5 mov 1, %g7 srlx %g5, 21 + 28, %g5 diff --git a/arch/sparc/mm/init_64.c b/arch/sparc/mm/init_64.c index ed6be6ba2f4..a70a5e1904d 100644 --- a/arch/sparc/mm/init_64.c +++ b/arch/sparc/mm/init_64.c @@ -145,7 +145,8 @@ static void __init read_obp_memory(const char *property, cmp_p64, NULL); } -unsigned long *sparc64_valid_addr_bitmap __read_mostly; +unsigned long sparc64_valid_addr_bitmap[VALID_ADDR_BITMAP_BYTES / + sizeof(unsigned long)]; EXPORT_SYMBOL(sparc64_valid_addr_bitmap); /* Kernel physical address base and size in bytes. */ @@ -1874,7 +1875,7 @@ static int pavail_rescan_ents __initdata; * memory list again, and make sure it provides at least as much * memory as 'pavail' does. */ -static void __init setup_valid_addr_bitmap_from_pavail(void) +static void __init setup_valid_addr_bitmap_from_pavail(unsigned long *bitmap) { int i; @@ -1897,8 +1898,7 @@ static void __init setup_valid_addr_bitmap_from_pavail(void) if (new_start <= old_start && new_end >= (old_start + PAGE_SIZE)) { - set_bit(old_start >> 22, - sparc64_valid_addr_bitmap); + set_bit(old_start >> 22, bitmap); goto do_next_page; } } @@ -1919,20 +1919,21 @@ static void __init setup_valid_addr_bitmap_from_pavail(void) } } +static void __init patch_tlb_miss_handler_bitmap(void) +{ + extern unsigned int valid_addr_bitmap_insn[]; + extern unsigned int valid_addr_bitmap_patch[]; + + valid_addr_bitmap_insn[1] = valid_addr_bitmap_patch[1]; + mb(); + valid_addr_bitmap_insn[0] = valid_addr_bitmap_patch[0]; + flushi(&valid_addr_bitmap_insn[0]); +} + void __init mem_init(void) { unsigned long codepages, datapages, initpages; unsigned long addr, last; - int i; - - i = last_valid_pfn >> ((22 - PAGE_SHIFT) + 6); - i += 1; - sparc64_valid_addr_bitmap = (unsigned long *) alloc_bootmem(i << 3); - if (sparc64_valid_addr_bitmap == NULL) { - prom_printf("mem_init: Cannot alloc valid_addr_bitmap.\n"); - prom_halt(); - } - memset(sparc64_valid_addr_bitmap, 0, i << 3); addr = PAGE_OFFSET + kern_base; last = PAGE_ALIGN(kern_size) + addr; @@ -1941,15 +1942,19 @@ void __init mem_init(void) addr += PAGE_SIZE; } - setup_valid_addr_bitmap_from_pavail(); + setup_valid_addr_bitmap_from_pavail(sparc64_valid_addr_bitmap); + patch_tlb_miss_handler_bitmap(); high_memory = __va(last_valid_pfn << PAGE_SHIFT); #ifdef CONFIG_NEED_MULTIPLE_NODES - for_each_online_node(i) { - if (NODE_DATA(i)->node_spanned_pages != 0) { - totalram_pages += - free_all_bootmem_node(NODE_DATA(i)); + { + int i; + for_each_online_node(i) { + if (NODE_DATA(i)->node_spanned_pages != 0) { + totalram_pages += + free_all_bootmem_node(NODE_DATA(i)); + } } } #else diff --git a/arch/sparc/mm/init_64.h b/arch/sparc/mm/init_64.h index 16063870a48..c2f772dbd55 100644 --- a/arch/sparc/mm/init_64.h +++ b/arch/sparc/mm/init_64.h @@ -5,10 +5,13 @@ * marked non-static so that assembler code can get at them. */ -#define MAX_PHYS_ADDRESS (1UL << 42UL) -#define KPTE_BITMAP_CHUNK_SZ (256UL * 1024UL * 1024UL) +#define MAX_PHYS_ADDRESS (1UL << 41UL) +#define KPTE_BITMAP_CHUNK_SZ (256UL * 1024UL * 1024UL) #define KPTE_BITMAP_BYTES \ ((MAX_PHYS_ADDRESS / KPTE_BITMAP_CHUNK_SZ) / 8) +#define VALID_ADDR_BITMAP_CHUNK_SZ (4UL * 1024UL * 1024UL) +#define VALID_ADDR_BITMAP_BYTES \ + ((MAX_PHYS_ADDRESS / VALID_ADDR_BITMAP_CHUNK_SZ) / 8) extern unsigned long kern_linear_pte_xor[2]; extern unsigned long kpte_linear_bitmap[KPTE_BITMAP_BYTES / sizeof(unsigned long)]; -- GitLab From 730a9cfc2dcead5538c0c96a046000d97140b0c0 Mon Sep 17 00:00:00 2001 From: Alexander Beregalov Date: Tue, 25 Aug 2009 20:39:18 -0700 Subject: [PATCH 1306/1342] irda/au1k_ir: fix broken netdev_ops conversion This patch is based on commit d2f3ad4 (pxaficp-ir: remove incorrect net_device_ops). Do the same for au1k_ir. Untested. Signed-off-by: Alexander Beregalov Signed-off-by: David S. Miller --- drivers/net/irda/au1k_ir.c | 4 ---- 1 file changed, 4 deletions(-) diff --git a/drivers/net/irda/au1k_ir.c b/drivers/net/irda/au1k_ir.c index c4361d46659..ee1cff5c9b2 100644 --- a/drivers/net/irda/au1k_ir.c +++ b/drivers/net/irda/au1k_ir.c @@ -23,7 +23,6 @@ #include #include #include -#include #include #include #include @@ -205,9 +204,6 @@ static const struct net_device_ops au1k_irda_netdev_ops = { .ndo_start_xmit = au1k_irda_hard_xmit, .ndo_tx_timeout = au1k_tx_timeout, .ndo_do_ioctl = au1k_irda_ioctl, - .ndo_change_mtu = eth_change_mtu, - .ndo_validate_addr = eth_validate_addr, - .ndo_set_mac_address = eth_mac_addr, }; static int au1k_irda_net_init(struct net_device *dev) -- GitLab From 4484b9c8b4976acee181d377f8ba571109d1a2be Mon Sep 17 00:00:00 2001 From: Alexander Beregalov Date: Tue, 25 Aug 2009 20:39:37 -0700 Subject: [PATCH 1307/1342] irda/sa1100_ir: fix broken netdev_ops conversion This patch is based on commit d2f3ad4 (pxaficp-ir: remove incorrect net_device_ops). Do the same for sa1100_ir. Untested. Signed-off-by: Alexander Beregalov Signed-off-by: David S. Miller --- drivers/net/irda/sa1100_ir.c | 4 ---- 1 file changed, 4 deletions(-) diff --git a/drivers/net/irda/sa1100_ir.c b/drivers/net/irda/sa1100_ir.c index 2aeb2e6aec1..b039cb081e9 100644 --- a/drivers/net/irda/sa1100_ir.c +++ b/drivers/net/irda/sa1100_ir.c @@ -24,7 +24,6 @@ #include #include #include -#include #include #include #include @@ -881,9 +880,6 @@ static const struct net_device_ops sa1100_irda_netdev_ops = { .ndo_stop = sa1100_irda_stop, .ndo_start_xmit = sa1100_irda_hard_xmit, .ndo_do_ioctl = sa1100_irda_ioctl, - .ndo_change_mtu = eth_change_mtu, - .ndo_validate_addr = eth_validate_addr, - .ndo_set_mac_address = eth_mac_addr, }; static int sa1100_irda_probe(struct platform_device *pdev) -- GitLab From 0b4f2928f14c4a9770b0866923fc81beb7f4aa57 Mon Sep 17 00:00:00 2001 From: Alexey Dobriyan Date: Wed, 26 Aug 2009 12:03:35 -0700 Subject: [PATCH 1308/1342] smc91x: fix compilation on SMP Signed-off-by: Alexey Dobriyan Signed-off-by: David S. Miller --- drivers/net/smc91x.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/smc91x.c b/drivers/net/smc91x.c index 9da1fa12a67..7567f510eff 100644 --- a/drivers/net/smc91x.c +++ b/drivers/net/smc91x.c @@ -531,7 +531,7 @@ static inline void smc_rcv(struct net_device *dev) local_irq_restore(flags); \ __ret; \ }) -#define smc_special_lock(lock, flags) spin_lock_irq(lock, flags) +#define smc_special_lock(lock, flags) spin_lock_irqsave(lock, flags) #define smc_special_unlock(lock, flags) spin_unlock_irqrestore(lock, flags) #else #define smc_special_trylock(lock, flags) (1) -- GitLab From 3161e453e496eb5643faad30fff5a5ab183da0fe Mon Sep 17 00:00:00 2001 From: Rusty Russell Date: Wed, 26 Aug 2009 12:22:32 -0700 Subject: [PATCH 1309/1342] virtio: net refill on out-of-memory If we run out of memory, use keventd to fill the buffer. There's a report of this happening: "Page allocation failures in guest", Message-ID: <20090713115158.0a4892b0@mjolnir.ossman.eu> Signed-off-by: Rusty Russell Signed-off-by: David S. Miller --- drivers/net/virtio_net.c | 61 ++++++++++++++++++++++++++++++---------- 1 file changed, 46 insertions(+), 15 deletions(-) diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c index 2a6e81d5b57..bbedf03a212 100644 --- a/drivers/net/virtio_net.c +++ b/drivers/net/virtio_net.c @@ -70,6 +70,9 @@ struct virtnet_info struct sk_buff_head recv; struct sk_buff_head send; + /* Work struct for refilling if we run low on memory. */ + struct delayed_work refill; + /* Chain pages by the private ptr. */ struct page *pages; }; @@ -273,19 +276,22 @@ drop: dev_kfree_skb(skb); } -static void try_fill_recv_maxbufs(struct virtnet_info *vi) +static bool try_fill_recv_maxbufs(struct virtnet_info *vi, gfp_t gfp) { struct sk_buff *skb; struct scatterlist sg[2+MAX_SKB_FRAGS]; int num, err, i; + bool oom = false; sg_init_table(sg, 2+MAX_SKB_FRAGS); for (;;) { struct virtio_net_hdr *hdr; skb = netdev_alloc_skb(vi->dev, MAX_PACKET_LEN + NET_IP_ALIGN); - if (unlikely(!skb)) + if (unlikely(!skb)) { + oom = true; break; + } skb_reserve(skb, NET_IP_ALIGN); skb_put(skb, MAX_PACKET_LEN); @@ -296,7 +302,7 @@ static void try_fill_recv_maxbufs(struct virtnet_info *vi) if (vi->big_packets) { for (i = 0; i < MAX_SKB_FRAGS; i++) { skb_frag_t *f = &skb_shinfo(skb)->frags[i]; - f->page = get_a_page(vi, GFP_ATOMIC); + f->page = get_a_page(vi, gfp); if (!f->page) break; @@ -325,31 +331,35 @@ static void try_fill_recv_maxbufs(struct virtnet_info *vi) if (unlikely(vi->num > vi->max)) vi->max = vi->num; vi->rvq->vq_ops->kick(vi->rvq); + return !oom; } -static void try_fill_recv(struct virtnet_info *vi) +/* Returns false if we couldn't fill entirely (OOM). */ +static bool try_fill_recv(struct virtnet_info *vi, gfp_t gfp) { struct sk_buff *skb; struct scatterlist sg[1]; int err; + bool oom = false; - if (!vi->mergeable_rx_bufs) { - try_fill_recv_maxbufs(vi); - return; - } + if (!vi->mergeable_rx_bufs) + return try_fill_recv_maxbufs(vi, gfp); for (;;) { skb_frag_t *f; skb = netdev_alloc_skb(vi->dev, GOOD_COPY_LEN + NET_IP_ALIGN); - if (unlikely(!skb)) + if (unlikely(!skb)) { + oom = true; break; + } skb_reserve(skb, NET_IP_ALIGN); f = &skb_shinfo(skb)->frags[0]; - f->page = get_a_page(vi, GFP_ATOMIC); + f->page = get_a_page(vi, gfp); if (!f->page) { + oom = true; kfree_skb(skb); break; } @@ -373,6 +383,7 @@ static void try_fill_recv(struct virtnet_info *vi) if (unlikely(vi->num > vi->max)) vi->max = vi->num; vi->rvq->vq_ops->kick(vi->rvq); + return !oom; } static void skb_recv_done(struct virtqueue *rvq) @@ -385,6 +396,23 @@ static void skb_recv_done(struct virtqueue *rvq) } } +static void refill_work(struct work_struct *work) +{ + struct virtnet_info *vi; + bool still_empty; + + vi = container_of(work, struct virtnet_info, refill.work); + napi_disable(&vi->napi); + try_fill_recv(vi, GFP_KERNEL); + still_empty = (vi->num == 0); + napi_enable(&vi->napi); + + /* In theory, this can happen: if we don't get any buffers in + * we will *never* try to fill again. */ + if (still_empty) + schedule_delayed_work(&vi->refill, HZ/2); +} + static int virtnet_poll(struct napi_struct *napi, int budget) { struct virtnet_info *vi = container_of(napi, struct virtnet_info, napi); @@ -400,10 +428,10 @@ again: received++; } - /* FIXME: If we oom and completely run out of inbufs, we need - * to start a timer trying to fill more. */ - if (vi->num < vi->max / 2) - try_fill_recv(vi); + if (vi->num < vi->max / 2) { + if (!try_fill_recv(vi, GFP_ATOMIC)) + schedule_delayed_work(&vi->refill, 0); + } /* Out of packets? */ if (received < budget) { @@ -893,6 +921,7 @@ static int virtnet_probe(struct virtio_device *vdev) vi->vdev = vdev; vdev->priv = vi; vi->pages = NULL; + INIT_DELAYED_WORK(&vi->refill, refill_work); /* If they give us a callback when all buffers are done, we don't need * the timer. */ @@ -941,7 +970,7 @@ static int virtnet_probe(struct virtio_device *vdev) } /* Last of all, set up some receive buffers. */ - try_fill_recv(vi); + try_fill_recv(vi, GFP_KERNEL); /* If we didn't even get one input buffer, we're useless. */ if (vi->num == 0) { @@ -958,6 +987,7 @@ static int virtnet_probe(struct virtio_device *vdev) unregister: unregister_netdev(dev); + cancel_delayed_work_sync(&vi->refill); free_vqs: vdev->config->del_vqs(vdev); free: @@ -986,6 +1016,7 @@ static void virtnet_remove(struct virtio_device *vdev) BUG_ON(vi->num != 0); unregister_netdev(vi->dev); + cancel_delayed_work_sync(&vi->refill); vdev->config->del_vqs(vi->vdev); -- GitLab From dac9ff79a8122b30176e23359bb879b3144d7f1f Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Wed, 17 Jun 2009 13:13:56 -0700 Subject: [PATCH 1310/1342] m68k: count can reach 51, not 50 With while (count++ < 50) { ... } count can reach 51, not 50, so we shouldn't give an error message on a count of 50. [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Roel Kluin Cc: Geert Uytterhoeven Signed-off-by: Andrew Morton Signed-off-by: Geert Uytterhoeven --- drivers/macintosh/via-maciisi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/macintosh/via-maciisi.c b/drivers/macintosh/via-maciisi.c index 4d686c0bdea..9ab5b0c34f0 100644 --- a/drivers/macintosh/via-maciisi.c +++ b/drivers/macintosh/via-maciisi.c @@ -288,7 +288,7 @@ static void maciisi_sync(struct adb_request *req) } /* This could be BAD... when the ADB controller doesn't respond * for this long, it's probably not coming back :-( */ - if(count >= 50) /* Hopefully shouldn't happen */ + if (count > 50) /* Hopefully shouldn't happen */ printk(KERN_ERR "maciisi_send_request: poll timed out!\n"); } -- GitLab From dd9b3e84f2095ed19582f4df5d20e1e40c01ca3c Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Wed, 17 Jun 2009 13:13:57 -0700 Subject: [PATCH 1311/1342] m68k: cnt reaches -1, not 0 With the postfix decrement cnt reaches -1 rather than 0. Signed-off-by: Roel Kluin Cc: Geert Uytterhoeven Signed-off-by: Andrew Morton Signed-off-by: Geert Uytterhoeven --- arch/m68k/amiga/config.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/arch/m68k/amiga/config.c b/arch/m68k/amiga/config.c index 6e562751ad5..6c74751c7b8 100644 --- a/arch/m68k/amiga/config.c +++ b/arch/m68k/amiga/config.c @@ -574,10 +574,11 @@ static int a2000_hwclk(int op, struct rtc_time *t) tod_2000.cntrl1 = TOD2000_CNTRL1_HOLD; - while ((tod_2000.cntrl1 & TOD2000_CNTRL1_BUSY) && cnt--) { + while ((tod_2000.cntrl1 & TOD2000_CNTRL1_BUSY) && cnt) { tod_2000.cntrl1 &= ~TOD2000_CNTRL1_HOLD; udelay(70); tod_2000.cntrl1 |= TOD2000_CNTRL1_HOLD; + --cnt; } if (!cnt) @@ -649,10 +650,11 @@ static int amiga_set_clock_mmss(unsigned long nowtime) tod_2000.cntrl1 |= TOD2000_CNTRL1_HOLD; - while ((tod_2000.cntrl1 & TOD2000_CNTRL1_BUSY) && cnt--) { + while ((tod_2000.cntrl1 & TOD2000_CNTRL1_BUSY) && cnt) { tod_2000.cntrl1 &= ~TOD2000_CNTRL1_HOLD; udelay(70); tod_2000.cntrl1 |= TOD2000_CNTRL1_HOLD; + --cnt; } if (!cnt) -- GitLab From dc71c7d5dbd8cd8bb6e3b548ddc0454b64ded5f8 Mon Sep 17 00:00:00 2001 From: Andrew Morton Date: Wed, 17 Jun 2009 13:13:58 -0700 Subject: [PATCH 1312/1342] arch/m68k/include/asm/motorola_pgalloc.h: fix kunmap arg arch/m68k/include/asm/motorola_pgalloc.h: In function 'pte_alloc_one': arch/m68k/include/asm/motorola_pgalloc.h:44: warning: passing argument 1 of 'kunmap' from incompatible pointer type Also, remove unneeded test for kmap() failure. Signed-off-by: Andrew Morton Signed-off-by: Geert Uytterhoeven --- arch/m68k/include/asm/motorola_pgalloc.h | 10 ++++------ 1 file changed, 4 insertions(+), 6 deletions(-) diff --git a/arch/m68k/include/asm/motorola_pgalloc.h b/arch/m68k/include/asm/motorola_pgalloc.h index 15ee4c74a9f..2f02f264e69 100644 --- a/arch/m68k/include/asm/motorola_pgalloc.h +++ b/arch/m68k/include/asm/motorola_pgalloc.h @@ -36,12 +36,10 @@ static inline pgtable_t pte_alloc_one(struct mm_struct *mm, unsigned long addres return NULL; pte = kmap(page); - if (pte) { - __flush_page_to_ram(pte); - flush_tlb_kernel_page(pte); - nocache_page(pte); - } - kunmap(pte); + __flush_page_to_ram(pte); + flush_tlb_kernel_page(pte); + nocache_page(pte); + kunmap(page); pgtable_page_ctor(page); return page; } -- GitLab From 9fd926b4ab1e38ac5e3eb3ba0afb56726d90aa88 Mon Sep 17 00:00:00 2001 From: Alexey Dobriyan Date: Thu, 9 Jul 2009 17:08:38 +0400 Subject: [PATCH 1313/1342] m68k: Fix redefinition of pgprot_noncached arch/m68k/include/asm/pgtable_mm.h:148:1: warning: "pgprot_noncached" redefined In file included from arch/m68k/include/asm/pgtable_mm.h:138, from arch/m68k/include/asm/pgtable.h:4, from include/linux/mm.h:40, from include/linux/pagemap.h:7, from include/linux/blkdev.h:12, from arch/m68k/emu/nfblock.c:17: include/asm-generic/pgtable.h:133:1: warning: this is the location of the previous definition pgprot_noncached() should be defined _before_ including asm-generic/pgtable.h Signed-off-by: Alexey Dobriyan Signed-off-by: Geert Uytterhoeven --- arch/m68k/include/asm/pgtable_mm.h | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/arch/m68k/include/asm/pgtable_mm.h b/arch/m68k/include/asm/pgtable_mm.h index 0b604f0f192..fe60e1abaee 100644 --- a/arch/m68k/include/asm/pgtable_mm.h +++ b/arch/m68k/include/asm/pgtable_mm.h @@ -135,8 +135,6 @@ static inline void update_mmu_cache(struct vm_area_struct *vma, #endif #ifndef __ASSEMBLY__ -#include - /* * Macro to mark a page protection value as "uncacheable". */ @@ -154,6 +152,7 @@ static inline void update_mmu_cache(struct vm_area_struct *vma, ? (__pgprot((pgprot_val(prot) & _CACHEMASK040) | _PAGE_NOCACHE_S)) \ : (prot))) +#include #endif /* !__ASSEMBLY__ */ /* -- GitLab From 9848484fad9ddeb18f18f02f9ecdcd330ac9a216 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Fri, 21 Aug 2009 22:03:54 +0200 Subject: [PATCH 1314/1342] m68k,m68knommu: Wire up rt_tgsigqueueinfo and perf_counter_open Signed-off-by: Geert Uytterhoeven Acked-by: Greg Ungerer --- arch/m68k/include/asm/unistd.h | 4 +++- arch/m68k/kernel/entry.S | 2 ++ arch/m68knommu/kernel/syscalltable.S | 2 ++ 3 files changed, 7 insertions(+), 1 deletion(-) diff --git a/arch/m68k/include/asm/unistd.h b/arch/m68k/include/asm/unistd.h index aa29a8640f7..946d8691f2b 100644 --- a/arch/m68k/include/asm/unistd.h +++ b/arch/m68k/include/asm/unistd.h @@ -334,10 +334,12 @@ #define __NR_inotify_init1 328 #define __NR_preadv 329 #define __NR_pwritev 330 +#define __NR_rt_tgsigqueueinfo 331 +#define __NR_perf_counter_open 332 #ifdef __KERNEL__ -#define NR_syscalls 331 +#define NR_syscalls 333 #define __ARCH_WANT_IPC_PARSE_VERSION #define __ARCH_WANT_OLD_READDIR diff --git a/arch/m68k/kernel/entry.S b/arch/m68k/kernel/entry.S index 8744f60c07a..c3735cd6207 100644 --- a/arch/m68k/kernel/entry.S +++ b/arch/m68k/kernel/entry.S @@ -755,4 +755,6 @@ sys_call_table: .long sys_inotify_init1 .long sys_preadv .long sys_pwritev /* 330 */ + .long sys_rt_tgsigqueueinfo + .long sys_perf_counter_open diff --git a/arch/m68knommu/kernel/syscalltable.S b/arch/m68knommu/kernel/syscalltable.S index c0b8782832f..0ae123e0898 100644 --- a/arch/m68knommu/kernel/syscalltable.S +++ b/arch/m68knommu/kernel/syscalltable.S @@ -349,6 +349,8 @@ ENTRY(sys_call_table) .long sys_inotify_init1 .long sys_preadv .long sys_pwritev /* 330 */ + .long sys_rt_tgsigqueueinfo + .long sys_perf_counter_open .rept NR_syscalls-(.-sys_call_table)/4 .long sys_ni_syscall -- GitLab From 53a7197aff20e341487fca8575275056fe1c63e5 Mon Sep 17 00:00:00 2001 From: Eric Paris Date: Wed, 26 Aug 2009 14:56:48 -0400 Subject: [PATCH 1315/1342] IMA: iint put in ima_counts_get and put ima_counts_get() calls ima_iint_find_insert_get() which takes a reference to the iint in question, but does not put that reference at the end of the function. This can lead to a nasty memory leak. Easy enough to reproduce: #include #include int main (void) { int i; void *ptr; for (i=0; i < 100000; i++) { ptr = mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_SHARED|MAP_ANONYMOUS, -1, 0); if (ptr == MAP_FAILED) return 2; munmap(ptr, 4096); } return 0; } Signed-off-by: Eric Paris Signed-off-by: James Morris --- security/integrity/ima/ima_main.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/security/integrity/ima/ima_main.c b/security/integrity/ima/ima_main.c index 101c512564e..4732f5e5d12 100644 --- a/security/integrity/ima/ima_main.c +++ b/security/integrity/ima/ima_main.c @@ -262,6 +262,8 @@ void ima_counts_put(struct path *path, int mask) else if (mask & (MAY_READ | MAY_EXEC)) iint->readcount--; mutex_unlock(&iint->mutex); + + kref_put(&iint->refcount, iint_free); } /* @@ -291,6 +293,8 @@ void ima_counts_get(struct file *file) if (file->f_mode & FMODE_WRITE) iint->writecount++; mutex_unlock(&iint->mutex); + + kref_put(&iint->refcount, iint_free); } EXPORT_SYMBOL_GPL(ima_counts_get); -- GitLab From 054b2b13ccba4876a1ce98a7ede7dab7d6893d01 Mon Sep 17 00:00:00 2001 From: Joonwoo Park Date: Wed, 26 Aug 2009 14:29:18 -0700 Subject: [PATCH 1316/1342] pps: fix incorrect verdict check Fix incorrect verdict check and returns error if device_create failed, otherwise driver triggers kernel oops. Signed-off-by: Joonwoo Park Cc: Rodolfo Giometti Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/pps/pps.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/pps/pps.c b/drivers/pps/pps.c index ac8cc8cea1e..fea17e7805e 100644 --- a/drivers/pps/pps.c +++ b/drivers/pps/pps.c @@ -244,7 +244,7 @@ int pps_register_cdev(struct pps_device *pps) } pps->dev = device_create(pps_class, pps->info.dev, pps->devno, NULL, "pps%d", pps->id); - if (err) + if (IS_ERR(pps->dev)) goto del_cdev; dev_set_drvdata(pps->dev, pps); -- GitLab From a30b595d2ca6d39e784a1bed5f2b35f3d7a03af7 Mon Sep 17 00:00:00 2001 From: David Rientjes Date: Wed, 26 Aug 2009 14:29:20 -0700 Subject: [PATCH 1317/1342] flex_array: fix get function for elements in base starting at non-zero If all array elements fit into the base structure and data is copied using flex_array_put() starting at a non-zero index, flex_array_get() will fail to return the data. This fixes the bug by only checking for NULL parts when all elements do not fit in the base structure when flex_array_get() is used. Otherwise, fa_element_to_part_nr() will always be 0 since there are no parts structures needed and such element may never have been put. Thus, it will remain NULL due to the kzalloc() of the base. Additionally, flex_array_put() now only checks for a NULL part when all elements do not fit in the base structure. This is otherwise unnecessary since the base structure is guaranteed to exist (or we would have already hit a NULL pointer). Signed-off-by: David Rientjes Acked-by: Dave Hansen Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- lib/flex_array.c | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-) diff --git a/lib/flex_array.c b/lib/flex_array.c index 08f1636d296..e73c691aec3 100644 --- a/lib/flex_array.c +++ b/lib/flex_array.c @@ -198,10 +198,11 @@ int flex_array_put(struct flex_array *fa, int element_nr, void *src, gfp_t flags return -ENOSPC; if (elements_fit_in_base(fa)) part = (struct flex_array_part *)&fa->parts[0]; - else + else { part = __fa_get_part(fa, part_nr, flags); - if (!part) - return -ENOMEM; + if (!part) + return -ENOMEM; + } dst = &part->elements[index_inside_part(fa, element_nr)]; memcpy(dst, src, fa->element_size); return 0; @@ -257,11 +258,12 @@ void *flex_array_get(struct flex_array *fa, int element_nr) if (element_nr >= fa->total_nr_elements) return NULL; - if (!fa->parts[part_nr]) - return NULL; if (elements_fit_in_base(fa)) part = (struct flex_array_part *)&fa->parts[0]; - else + else { part = fa->parts[part_nr]; + if (!part) + return NULL; + } return &part->elements[index_inside_part(fa, element_nr)]; } -- GitLab From 105b6e8a74cac11cdf70903877593c7f202075cc Mon Sep 17 00:00:00 2001 From: David Rientjes Date: Wed, 26 Aug 2009 14:29:20 -0700 Subject: [PATCH 1318/1342] flex_array: fix flex_array_free_parts comment flex_array_free_parts() does not take `src' or `element_nr' formals, so remove their respective comments. Signed-off-by: David Rientjes Acked-by: Dave Hansen Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- lib/flex_array.c | 3 --- 1 file changed, 3 deletions(-) diff --git a/lib/flex_array.c b/lib/flex_array.c index e73c691aec3..cf4e372cae9 100644 --- a/lib/flex_array.c +++ b/lib/flex_array.c @@ -122,9 +122,6 @@ static int fa_element_to_part_nr(struct flex_array *fa, int element_nr) /** * flex_array_free_parts - just free the second-level pages - * @src: address of data to copy into the array - * @element_nr: index of the position in which to insert - * the new element. * * This is to be used in cases where the base 'struct flex_array' * has been statically allocated and should not be free. -- GitLab From 8e7ee27095aee87b5db1b0061e2ceea5878a1bbd Mon Sep 17 00:00:00 2001 From: David Rientjes Date: Wed, 26 Aug 2009 14:29:21 -0700 Subject: [PATCH 1319/1342] flex_array: declare parts member to have incomplete type The `parts' member of struct flex_array should evaluate to an incomplete type so that sizeof() cannot be used and C99 does not require the zero-length specification. Signed-off-by: David Rientjes Acked-by: Dave Hansen Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- include/linux/flex_array.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/linux/flex_array.h b/include/linux/flex_array.h index 23c1ec79a31..603160db7c9 100644 --- a/include/linux/flex_array.h +++ b/include/linux/flex_array.h @@ -21,7 +21,7 @@ struct flex_array { struct { int element_size; int total_nr_elements; - struct flex_array_part *parts[0]; + struct flex_array_part *parts[]; }; /* * This little trick makes sure that -- GitLab From b62e408c05228f40e69bb38a48db8961cac6cd23 Mon Sep 17 00:00:00 2001 From: David Rientjes Date: Wed, 26 Aug 2009 14:29:22 -0700 Subject: [PATCH 1320/1342] flex_array: convert element_nr formals to unsigned It's problematic to allow signed element_nr's or total's to be passed as part of the flex array API. flex_array_alloc() allows total_nr_elements to be set to a negative quantity, which is obviously erroneous. flex_array_get() and flex_array_put() allows negative array indices in dereferencing an array part, which could address memory mapped before struct flex_array. The fix is to convert all existing element_nr formals to be qualified as unsigned. Existing checks to compare it to total_nr_elements or the max array size based on element_size need not be changed. Signed-off-by: David Rientjes Cc: Dave Hansen Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- include/linux/flex_array.h | 10 ++++++---- lib/flex_array.c | 24 +++++++++++++----------- 2 files changed, 19 insertions(+), 15 deletions(-) diff --git a/include/linux/flex_array.h b/include/linux/flex_array.h index 603160db7c9..45ff1849151 100644 --- a/include/linux/flex_array.h +++ b/include/linux/flex_array.h @@ -36,12 +36,14 @@ struct flex_array { .total_nr_elements = (total), \ } } } -struct flex_array *flex_array_alloc(int element_size, int total, gfp_t flags); -int flex_array_prealloc(struct flex_array *fa, int start, int end, gfp_t flags); +struct flex_array *flex_array_alloc(int element_size, unsigned int total, + gfp_t flags); +int flex_array_prealloc(struct flex_array *fa, unsigned int start, + unsigned int end, gfp_t flags); void flex_array_free(struct flex_array *fa); void flex_array_free_parts(struct flex_array *fa); -int flex_array_put(struct flex_array *fa, int element_nr, void *src, +int flex_array_put(struct flex_array *fa, unsigned int element_nr, void *src, gfp_t flags); -void *flex_array_get(struct flex_array *fa, int element_nr); +void *flex_array_get(struct flex_array *fa, unsigned int element_nr); #endif /* _FLEX_ARRAY_H */ diff --git a/lib/flex_array.c b/lib/flex_array.c index cf4e372cae9..7baed2fc3bc 100644 --- a/lib/flex_array.c +++ b/lib/flex_array.c @@ -99,7 +99,8 @@ static inline int elements_fit_in_base(struct flex_array *fa) * capacity in the base structure. Also note that no effort is made * to efficiently pack objects across page boundaries. */ -struct flex_array *flex_array_alloc(int element_size, int total, gfp_t flags) +struct flex_array *flex_array_alloc(int element_size, unsigned int total, + gfp_t flags) { struct flex_array *ret; int max_size = nr_base_part_ptrs() * __elements_per_part(element_size); @@ -115,7 +116,8 @@ struct flex_array *flex_array_alloc(int element_size, int total, gfp_t flags) return ret; } -static int fa_element_to_part_nr(struct flex_array *fa, int element_nr) +static int fa_element_to_part_nr(struct flex_array *fa, + unsigned int element_nr) { return element_nr / __elements_per_part(fa->element_size); } @@ -143,14 +145,12 @@ void flex_array_free(struct flex_array *fa) kfree(fa); } -static int fa_index_inside_part(struct flex_array *fa, int element_nr) +static unsigned int index_inside_part(struct flex_array *fa, + unsigned int element_nr) { - return element_nr % __elements_per_part(fa->element_size); -} + unsigned int part_offset; -static int index_inside_part(struct flex_array *fa, int element_nr) -{ - int part_offset = fa_index_inside_part(fa, element_nr); + part_offset = element_nr % __elements_per_part(fa->element_size); return part_offset * fa->element_size; } @@ -185,7 +185,8 @@ __fa_get_part(struct flex_array *fa, int part_nr, gfp_t flags) * * Locking must be provided by the caller. */ -int flex_array_put(struct flex_array *fa, int element_nr, void *src, gfp_t flags) +int flex_array_put(struct flex_array *fa, unsigned int element_nr, void *src, + gfp_t flags) { int part_nr = fa_element_to_part_nr(fa, element_nr); struct flex_array_part *part; @@ -217,7 +218,8 @@ int flex_array_put(struct flex_array *fa, int element_nr, void *src, gfp_t flags * * Locking must be provided by the caller. */ -int flex_array_prealloc(struct flex_array *fa, int start, int end, gfp_t flags) +int flex_array_prealloc(struct flex_array *fa, unsigned int start, + unsigned int end, gfp_t flags) { int start_part; int end_part; @@ -248,7 +250,7 @@ int flex_array_prealloc(struct flex_array *fa, int start, int end, gfp_t flags) * * Locking must be provided by the caller. */ -void *flex_array_get(struct flex_array *fa, int element_nr) +void *flex_array_get(struct flex_array *fa, unsigned int element_nr) { int part_nr = fa_element_to_part_nr(fa, element_nr); struct flex_array_part *part; -- GitLab From 03ef83af528899aa339e42d8024b37e2f434fba4 Mon Sep 17 00:00:00 2001 From: Minchan Kim Date: Wed, 26 Aug 2009 14:29:23 -0700 Subject: [PATCH 1321/1342] mm: fix for infinite churning of mlocked pages An mlocked page might lose the isolatation race. This causes the page to clear PG_mlocked while it remains in a VM_LOCKED vma. This means it can be put onto the [in]active list. We can rescue it by using try_to_unmap() in shrink_page_list(). But now, As Wu Fengguang pointed out, vmscan has a bug. If the page has PG_referenced, it can't reach try_to_unmap() in shrink_page_list() but is put into the active list. If the page is referenced repeatedly, it can remain on the [in]active list without being moving to the unevictable list. This patch fixes it. Reported-by: Wu Fengguang Signed-off-by: Minchan Kim Reviewed-by: KOSAKI Motohiro < Cc: Lee Schermerhorn Acked-by: Rik van Riel Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- mm/rmap.c | 1 + mm/vmscan.c | 9 +++++++-- 2 files changed, 8 insertions(+), 2 deletions(-) diff --git a/mm/rmap.c b/mm/rmap.c index 836c6c63e1f..0895b5c7cbf 100644 --- a/mm/rmap.c +++ b/mm/rmap.c @@ -358,6 +358,7 @@ static int page_referenced_one(struct page *page, */ if (vma->vm_flags & VM_LOCKED) { *mapcount = 1; /* break early from loop */ + *vm_flags |= VM_LOCKED; goto out_unmap; } diff --git a/mm/vmscan.c b/mm/vmscan.c index dea7abd3109..94e86dd6954 100644 --- a/mm/vmscan.c +++ b/mm/vmscan.c @@ -630,9 +630,14 @@ static unsigned long shrink_page_list(struct list_head *page_list, referenced = page_referenced(page, 1, sc->mem_cgroup, &vm_flags); - /* In active use or really unfreeable? Activate it. */ + /* + * In active use or really unfreeable? Activate it. + * If page which have PG_mlocked lost isoltation race, + * try_to_unmap moves it to unevictable list + */ if (sc->order <= PAGE_ALLOC_COSTLY_ORDER && - referenced && page_mapping_inuse(page)) + referenced && page_mapping_inuse(page) + && !(vm_flags & VM_LOCKED)) goto activate_locked; /* -- GitLab From 4ab6c08336535f8c8e42cf45d7adeda882eff06e Mon Sep 17 00:00:00 2001 From: Oleg Nesterov Date: Wed, 26 Aug 2009 14:29:24 -0700 Subject: [PATCH 1322/1342] clone(): fix race between copy_process() and de_thread() Spotted by Hiroshi Shimamoto who also provided the test-case below. copy_process() uses signal->count as a reference counter, but it is not. This test case #include #include #include #include #include #include void *null_thread(void *p) { for (;;) sleep(1); return NULL; } void *exec_thread(void *p) { execl("/bin/true", "/bin/true", NULL); return null_thread(p); } int main(int argc, char **argv) { for (;;) { pid_t pid; int ret, status; pid = fork(); if (pid < 0) break; if (!pid) { pthread_t tid; pthread_create(&tid, NULL, exec_thread, NULL); for (;;) pthread_create(&tid, NULL, null_thread, NULL); } do { ret = waitpid(pid, &status, 0); } while (ret == -1 && errno == EINTR); } return 0; } quickly creates an unkillable task. If copy_process(CLONE_THREAD) races with de_thread() copy_signal()->atomic(signal->count) breaks the signal->notify_count logic, and the execing thread can hang forever in kernel space. Change copy_process() to increment count/live only when we know for sure we can't fail. In this case the forked thread will take care of its reference to signal correctly. If copy_process() fails, check CLONE_THREAD flag. If it it set - do nothing, the counters were not changed and current belongs to the same thread group. If it is not set, ->signal must be released in any case (and ->count must be == 1), the forked child is the only thread in the thread group. We need more cleanups here, in particular signal->count should not be used by de_thread/__exit_signal at all. This patch only fixes the bug. Reported-by: Hiroshi Shimamoto Tested-by: Hiroshi Shimamoto Signed-off-by: Oleg Nesterov Acked-by: Roland McGrath Cc: KAMEZAWA Hiroyuki Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- kernel/fork.c | 20 +++++--------------- 1 file changed, 5 insertions(+), 15 deletions(-) diff --git a/kernel/fork.c b/kernel/fork.c index 144326b7af5..e6c04d462ab 100644 --- a/kernel/fork.c +++ b/kernel/fork.c @@ -815,11 +815,8 @@ static int copy_signal(unsigned long clone_flags, struct task_struct *tsk) { struct signal_struct *sig; - if (clone_flags & CLONE_THREAD) { - atomic_inc(¤t->signal->count); - atomic_inc(¤t->signal->live); + if (clone_flags & CLONE_THREAD) return 0; - } sig = kmem_cache_alloc(signal_cachep, GFP_KERNEL); tsk->signal = sig; @@ -877,16 +874,6 @@ void __cleanup_signal(struct signal_struct *sig) kmem_cache_free(signal_cachep, sig); } -static void cleanup_signal(struct task_struct *tsk) -{ - struct signal_struct *sig = tsk->signal; - - atomic_dec(&sig->live); - - if (atomic_dec_and_test(&sig->count)) - __cleanup_signal(sig); -} - static void copy_flags(unsigned long clone_flags, struct task_struct *p) { unsigned long new_flags = p->flags; @@ -1239,6 +1226,8 @@ static struct task_struct *copy_process(unsigned long clone_flags, } if (clone_flags & CLONE_THREAD) { + atomic_inc(¤t->signal->count); + atomic_inc(¤t->signal->live); p->group_leader = current->group_leader; list_add_tail_rcu(&p->thread_group, &p->group_leader->thread_group); } @@ -1282,7 +1271,8 @@ bad_fork_cleanup_mm: if (p->mm) mmput(p->mm); bad_fork_cleanup_signal: - cleanup_signal(p); + if (!(clone_flags & CLONE_THREAD)) + __cleanup_signal(p->signal); bad_fork_cleanup_sighand: __cleanup_sighand(p->sighand); bad_fork_cleanup_fs: -- GitLab From 0d288162f2afc42b37aab656f4622c076babbca3 Mon Sep 17 00:00:00 2001 From: Michael Brunner Date: Wed, 26 Aug 2009 14:29:25 -0700 Subject: [PATCH 1323/1342] thermal_sys: check get_temp return value The return value of the get_temp function is not checked when doing a thermal zone update. This may lead to a critical shutdown if get_temp fails and the content of the temp variable is incorrectly set higher than the critical trip point. This has been observed on a system with incorrect ACPI implementation where the corresponding methods were not serialized and therefore sometimes triggered ACPI errors (AE_ALREADY_EXISTS). The following critical shutdowns indicated a temperature of 2097 C, which was obviously wrong. The patch adds a return value check that jumps over all trip point evaluations printing a warning if get_temp fails. The trip points are evaluated again on the next polling interval with successful get_temp execution. Signed-off-by: Michael Brunner Acked-by: Zhang Rui Cc: Len Brown Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/thermal/thermal_sys.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) diff --git a/drivers/thermal/thermal_sys.c b/drivers/thermal/thermal_sys.c index 0a69672097a..4e83c297ec9 100644 --- a/drivers/thermal/thermal_sys.c +++ b/drivers/thermal/thermal_sys.c @@ -953,7 +953,12 @@ void thermal_zone_device_update(struct thermal_zone_device *tz) mutex_lock(&tz->lock); - tz->ops->get_temp(tz, &temp); + if (tz->ops->get_temp(tz, &temp)) { + /* get_temp failed - retry it later */ + printk(KERN_WARNING PREFIX "failed to read out thermal zone " + "%d\n", tz->id); + goto leave; + } for (count = 0; count < tz->trips; count++) { tz->ops->get_trip_type(tz, count, &trip_type); @@ -1005,6 +1010,8 @@ void thermal_zone_device_update(struct thermal_zone_device *tz) THERMAL_TRIPS_NONE); tz->last_temperature = temp; + + leave: if (tz->passive) thermal_zone_device_set_polling(tz, tz->passive_delay); else if (tz->polling_delay) -- GitLab From ce8442b55135c679809311997d1446f3bbc05de2 Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Wed, 26 Aug 2009 14:29:26 -0700 Subject: [PATCH 1324/1342] acpi: don't call acpi_processor_init if acpi is disabled Jens reported early_ioremap messages with old ASUS board... > [ 1.507461] pci 0000:00:09.0: Firmware left e100 interrupts enabled; disabling > [ 1.532778] early_ioremap(3fffd080, 0000005c) [0] => Pid: 1, comm: swapper Not tainted 2.6.31-rc4 #36 > [ 1.561007] Call Trace: > [ 1.568638] [] ? printk+0x18/0x1d > [ 1.581734] [] __early_ioremap+0x74/0x1e9 > [ 1.596898] [] early_ioremap+0x1a/0x1c > [ 1.611270] [] __acpi_map_table+0x18/0x1a > [ 1.626451] [] acpi_os_map_memory+0x1d/0x25 > [ 1.642129] [] acpi_tb_verify_table+0x20/0x49 > [ 1.658321] [] acpi_get_table_with_size+0x53/0xa1 > [ 1.675553] [] acpi_get_table+0x10/0x15 > [ 1.690192] [] acpi_processor_init+0x23/0xab > [ 1.706126] [] do_one_initcall+0x33/0x180 > [ 1.721279] [] ? acpi_processor_init+0x0/0xab > [ 1.737479] [] ? register_irq_proc+0xaa/0xc0 > [ 1.753411] [] ? init_irq_proc+0x67/0x80 > [ 1.768316] [] kernel_init+0x120/0x176 > [ 1.782678] [] ? kernel_init+0x0/0x176 > [ 1.797062] [] kernel_thread_helper+0x7/0x10 > [ 1.812984] 00000080 + ffe00000 that is rather later. acpi_gbl_permanent_mmap should be set in acpi_early_init() if acpi is not disabled and we have > [ 0.000000] ASUS P2B-DS detected: force use of acpi=ht just don't load acpi_processor_init... Reported-and-tested-by: Jens Rosenboom Signed-off-by: Yinghai Lu Acked-by: Ingo Molnar Cc: Len Brown Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/acpi/processor_core.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/acpi/processor_core.c b/drivers/acpi/processor_core.c index 84e0f3c0744..2cc4b303387 100644 --- a/drivers/acpi/processor_core.c +++ b/drivers/acpi/processor_core.c @@ -1151,6 +1151,9 @@ static int __init acpi_processor_init(void) { int result = 0; + if (acpi_disabled) + return 0; + memset(&errata, 0, sizeof(errata)); #ifdef CONFIG_SMP @@ -1197,6 +1200,9 @@ out_proc: static void __exit acpi_processor_exit(void) { + if (acpi_disabled) + return; + acpi_processor_ppc_exit(); acpi_thermal_cpufreq_exit(); -- GitLab From f3d83e2415445e5b157bef404d38674e9e8de169 Mon Sep 17 00:00:00 2001 From: Costantino Leandro Date: Wed, 26 Aug 2009 14:29:28 -0700 Subject: [PATCH 1325/1342] wmi: fix kernel panic when stack protection enabled. Summary: Kernel panic arise when stack protection is enabled, since strncat will add a null terminating byte '\0'; So in functions like this one (wmi_query_block): char wc[4]="WC"; .... strncat(method, block->object_id, 2); ... the length of wc should be n+1 (wc[5]) or stack protection fault will arise. This is not noticeable when stack protection is disabled,but , isn't good either. Config used: [CONFIG_CC_STACKPROTECTOR_ALL=y, CONFIG_CC_STACKPROTECTOR=y] Panic Trace ------------ .... stack-protector: kernel stack corrupted in : fa7b182c 2.6.30-rc8-obelisco-generic call_trace: [] ? panic+0x45/0xd9 [] ? __stack_chk_fail+0x1c/0x40 [] ? wmi_query_block+0x15a/0x162 [wmi] [] ? wmi_query_block+0x15a/0x162 [wmi] [] ? acer_wmi_init+0x00/0x61a [acer_wmi] [] ? acer_wmi_init+0x135/0x61a [acer_wmi] [] ? do_one_initcall+0x50+0x126 Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13514 Signed-off-by: Costantino Leandro Signed-off-by: Carlos Corbacho Cc: Len Brown Cc: Bjorn Helgaas Cc: "Rafael J. Wysocki" Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/platform/x86/wmi.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/platform/x86/wmi.c b/drivers/platform/x86/wmi.c index 043b208d971..f215a591919 100644 --- a/drivers/platform/x86/wmi.c +++ b/drivers/platform/x86/wmi.c @@ -270,7 +270,7 @@ u32 method_id, const struct acpi_buffer *in, struct acpi_buffer *out) acpi_status status; struct acpi_object_list input; union acpi_object params[3]; - char method[4] = "WM"; + char method[5] = "WM"; if (!find_guid(guid_string, &wblock)) return AE_ERROR; @@ -328,8 +328,8 @@ struct acpi_buffer *out) acpi_status status, wc_status = AE_ERROR; struct acpi_object_list input, wc_input; union acpi_object wc_params[1], wq_params[1]; - char method[4]; - char wc_method[4] = "WC"; + char method[5]; + char wc_method[5] = "WC"; if (!guid_string || !out) return AE_BAD_PARAMETER; @@ -410,7 +410,7 @@ const struct acpi_buffer *in) acpi_handle handle; struct acpi_object_list input; union acpi_object params[2]; - char method[4] = "WS"; + char method[5] = "WS"; if (!guid_string || !in) return AE_BAD_DATA; -- GitLab From 2a908002c7b1b666616103e9df2419b38d7c6f1f Mon Sep 17 00:00:00 2001 From: Frans Pop Date: Wed, 26 Aug 2009 14:29:29 -0700 Subject: [PATCH 1326/1342] ACPI processor: force throttling state when BIOS returns incorrect value If the BIOS reports an invalid throttling state (which seems to be fairly common after system boot), a reset is done to state T0. Because of a check in acpi_processor_get_throttling_ptc(), the reset never actually gets executed, which results in the error reoccurring on every access of for example /proc/acpi/processor/CPU0/throttling. Add a 'force' option to acpi_processor_set_throttling() to ensure the reset really takes effect. Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13389 This patch, together with the next one, fixes a regression introduced in 2.6.30, listed on the regression list. They have been available for 2.5 months now in bugzilla, but have not been picked up, despite various reminders and without any reason given. Google shows that numerous people are hitting this issue. The issue is in itself relatively minor, but the bug in the code is clear. The patches have been in all my kernels and today testing has shown that throttling works correctly with the patches applied when the system overheats (http://bugzilla.kernel.org/show_bug.cgi?id=13918#c14). Signed-off-by: Frans Pop Acked-by: Zhang Rui Cc: Len Brown Cc: "Rafael J. Wysocki" Cc: Rusty Russell Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/acpi/processor_thermal.c | 6 +++--- drivers/acpi/processor_throttling.c | 26 ++++++++++++++------------ include/acpi/processor.h | 5 +++-- 3 files changed, 20 insertions(+), 17 deletions(-) diff --git a/drivers/acpi/processor_thermal.c b/drivers/acpi/processor_thermal.c index 39838c66603..31adda1099e 100644 --- a/drivers/acpi/processor_thermal.c +++ b/drivers/acpi/processor_thermal.c @@ -66,7 +66,7 @@ static int acpi_processor_apply_limit(struct acpi_processor *pr) if (pr->limit.thermal.tx > tx) tx = pr->limit.thermal.tx; - result = acpi_processor_set_throttling(pr, tx); + result = acpi_processor_set_throttling(pr, tx, false); if (result) goto end; } @@ -421,12 +421,12 @@ processor_set_cur_state(struct thermal_cooling_device *cdev, if (state <= max_pstate) { if (pr->flags.throttling && pr->throttling.state) - result = acpi_processor_set_throttling(pr, 0); + result = acpi_processor_set_throttling(pr, 0, false); cpufreq_set_cur_state(pr->id, state); } else { cpufreq_set_cur_state(pr->id, max_pstate); result = acpi_processor_set_throttling(pr, - state - max_pstate); + state - max_pstate, false); } return result; } diff --git a/drivers/acpi/processor_throttling.c b/drivers/acpi/processor_throttling.c index 227543789ba..841be4ee210 100644 --- a/drivers/acpi/processor_throttling.c +++ b/drivers/acpi/processor_throttling.c @@ -62,7 +62,8 @@ struct throttling_tstate { #define THROTTLING_POSTCHANGE (2) static int acpi_processor_get_throttling(struct acpi_processor *pr); -int acpi_processor_set_throttling(struct acpi_processor *pr, int state); +int acpi_processor_set_throttling(struct acpi_processor *pr, + int state, bool force); static int acpi_processor_update_tsd_coord(void) { @@ -361,7 +362,7 @@ int acpi_processor_tstate_has_changed(struct acpi_processor *pr) */ target_state = throttling_limit; } - return acpi_processor_set_throttling(pr, target_state); + return acpi_processor_set_throttling(pr, target_state, false); } /* @@ -842,7 +843,7 @@ static int acpi_processor_get_throttling_ptc(struct acpi_processor *pr) ACPI_WARNING((AE_INFO, "Invalid throttling state, reset")); state = 0; - ret = acpi_processor_set_throttling(pr, state); + ret = acpi_processor_set_throttling(pr, state, true); if (ret) return ret; } @@ -915,7 +916,7 @@ static int acpi_processor_get_fadt_info(struct acpi_processor *pr) } static int acpi_processor_set_throttling_fadt(struct acpi_processor *pr, - int state) + int state, bool force) { u32 value = 0; u32 duty_mask = 0; @@ -930,7 +931,7 @@ static int acpi_processor_set_throttling_fadt(struct acpi_processor *pr, if (!pr->flags.throttling) return -ENODEV; - if (state == pr->throttling.state) + if (!force && (state == pr->throttling.state)) return 0; if (state < pr->throttling_platform_limit) @@ -988,7 +989,7 @@ static int acpi_processor_set_throttling_fadt(struct acpi_processor *pr, } static int acpi_processor_set_throttling_ptc(struct acpi_processor *pr, - int state) + int state, bool force) { int ret; acpi_integer value; @@ -1002,7 +1003,7 @@ static int acpi_processor_set_throttling_ptc(struct acpi_processor *pr, if (!pr->flags.throttling) return -ENODEV; - if (state == pr->throttling.state) + if (!force && (state == pr->throttling.state)) return 0; if (state < pr->throttling_platform_limit) @@ -1018,7 +1019,8 @@ static int acpi_processor_set_throttling_ptc(struct acpi_processor *pr, return 0; } -int acpi_processor_set_throttling(struct acpi_processor *pr, int state) +int acpi_processor_set_throttling(struct acpi_processor *pr, + int state, bool force) { cpumask_var_t saved_mask; int ret = 0; @@ -1070,7 +1072,7 @@ int acpi_processor_set_throttling(struct acpi_processor *pr, int state) /* FIXME: use work_on_cpu() */ set_cpus_allowed_ptr(current, cpumask_of(pr->id)); ret = p_throttling->acpi_processor_set_throttling(pr, - t_state.target_state); + t_state.target_state, force); } else { /* * When the T-state coordination is SW_ALL or HW_ALL, @@ -1103,7 +1105,7 @@ int acpi_processor_set_throttling(struct acpi_processor *pr, int state) set_cpus_allowed_ptr(current, cpumask_of(i)); ret = match_pr->throttling. acpi_processor_set_throttling( - match_pr, t_state.target_state); + match_pr, t_state.target_state, force); } } /* @@ -1201,7 +1203,7 @@ int acpi_processor_get_throttling_info(struct acpi_processor *pr) ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Disabling throttling (was T%d)\n", pr->throttling.state)); - result = acpi_processor_set_throttling(pr, 0); + result = acpi_processor_set_throttling(pr, 0, false); if (result) goto end; } @@ -1307,7 +1309,7 @@ static ssize_t acpi_processor_write_throttling(struct file *file, if (strcmp(tmpbuf, charp) != 0) return -EINVAL; - result = acpi_processor_set_throttling(pr, state_val); + result = acpi_processor_set_throttling(pr, state_val, false); if (result) return result; diff --git a/include/acpi/processor.h b/include/acpi/processor.h index baf1e0a9a7e..740ac3ad8fd 100644 --- a/include/acpi/processor.h +++ b/include/acpi/processor.h @@ -174,7 +174,7 @@ struct acpi_processor_throttling { cpumask_var_t shared_cpu_map; int (*acpi_processor_get_throttling) (struct acpi_processor * pr); int (*acpi_processor_set_throttling) (struct acpi_processor * pr, - int state); + int state, bool force); u32 address; u8 duty_offset; @@ -321,7 +321,8 @@ static inline int acpi_processor_ppc_has_changed(struct acpi_processor *pr) /* in processor_throttling.c */ int acpi_processor_tstate_has_changed(struct acpi_processor *pr); int acpi_processor_get_throttling_info(struct acpi_processor *pr); -extern int acpi_processor_set_throttling(struct acpi_processor *pr, int state); +extern int acpi_processor_set_throttling(struct acpi_processor *pr, + int state, bool force); extern const struct file_operations acpi_processor_throttling_fops; extern void acpi_processor_throttling_init(void); /* in processor_idle.c */ -- GitLab From bdf57de4e6abc389cc3f3bd94ec15cce74cf6f4b Mon Sep 17 00:00:00 2001 From: Frans Pop Date: Wed, 26 Aug 2009 14:29:30 -0700 Subject: [PATCH 1327/1342] acpi processor: remove superfluous warning message This failure is very common on many platforms. Handling it in the ACPI processor driver is enough, and we don't need a warning message unless CONFIG_ACPI_DEBUG is set. Based on a patch from Zhang Rui. Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13389 Signed-off-by: Frans Pop Acked-by: Zhang Rui Cc: Len Brown Cc: "Rafael J. Wysocki" Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/acpi/processor_throttling.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/acpi/processor_throttling.c b/drivers/acpi/processor_throttling.c index 841be4ee210..ae39797aab5 100644 --- a/drivers/acpi/processor_throttling.c +++ b/drivers/acpi/processor_throttling.c @@ -840,8 +840,8 @@ static int acpi_processor_get_throttling_ptc(struct acpi_processor *pr) if (ret >= 0) { state = acpi_get_throttling_state(pr, value); if (state == -1) { - ACPI_WARNING((AE_INFO, - "Invalid throttling state, reset")); + ACPI_DEBUG_PRINT((ACPI_DB_INFO, + "Invalid throttling state, reset\n")); state = 0; ret = acpi_processor_set_throttling(pr, state, true); if (ret) -- GitLab From 48cccd26f36511ddb6aeca07485ecf2829683907 Mon Sep 17 00:00:00 2001 From: Thadeu Lima de Souza Cascardo Date: Wed, 26 Aug 2009 14:29:31 -0700 Subject: [PATCH 1328/1342] leds: fix multiple requests and releases of IRQ for GPIO LED Trigger When setting the same GPIO number, multiple IRQ shared requests will be done without freing the previous request. It will also try to free a failed request or an already freed IRQ if 0 was written to the gpio file. All these oops and leaks were fixed with the following solution: keep the previous allocated GPIO (if any) still allocated in case the new request fails. The alternative solution would desallocate the previous allocated GPIO and set gpio as 0. Signed-off-by: Thadeu Lima de Souza Cascardo Signed-off-by: Samuel R. C. Vale Cc: Richard Purdie Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/leds/ledtrig-gpio.c | 21 ++++++++++++++------- 1 file changed, 14 insertions(+), 7 deletions(-) diff --git a/drivers/leds/ledtrig-gpio.c b/drivers/leds/ledtrig-gpio.c index a247ae63374..8183b81fca8 100644 --- a/drivers/leds/ledtrig-gpio.c +++ b/drivers/leds/ledtrig-gpio.c @@ -146,20 +146,26 @@ static ssize_t gpio_trig_gpio_store(struct device *dev, return -EINVAL; } + if (gpio_data->gpio == gpio) + return n; + if (!gpio) { - free_irq(gpio_to_irq(gpio_data->gpio), led); + if (gpio_data->gpio != 0) + free_irq(gpio_to_irq(gpio_data->gpio), led); + gpio_data->gpio = 0; return n; } - if (gpio_data->gpio > 0 && gpio_data->gpio != gpio) - free_irq(gpio_to_irq(gpio_data->gpio), led); - - gpio_data->gpio = gpio; ret = request_irq(gpio_to_irq(gpio), gpio_trig_irq, IRQF_SHARED | IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, "ledtrig-gpio", led); - if (ret) + if (ret) { dev_err(dev, "request_irq failed with error %d\n", ret); + } else { + if (gpio_data->gpio != 0) + free_irq(gpio_to_irq(gpio_data->gpio), led); + gpio_data->gpio = gpio; + } return ret ? ret : n; } @@ -211,7 +217,8 @@ static void gpio_trig_deactivate(struct led_classdev *led) device_remove_file(led->dev, &dev_attr_inverted); device_remove_file(led->dev, &dev_attr_desired_brightness); flush_work(&gpio_data->work); - free_irq(gpio_to_irq(gpio_data->gpio),led); + if (gpio_data->gpio != 0) + free_irq(gpio_to_irq(gpio_data->gpio), led); kfree(gpio_data); } } -- GitLab From cc674c81f01a6151ca00c617e5efa0812ee5fdbe Mon Sep 17 00:00:00 2001 From: Thadeu Lima de Souza Cascardo Date: Wed, 26 Aug 2009 14:29:32 -0700 Subject: [PATCH 1329/1342] leds: after setting inverted attribute, we must update the LED If we change the inverted attribute to another value, the LED will not be inverted until we change the GPIO state. Signed-off-by: Thadeu Lima de Souza Cascardo Cc: Samuel R. C. Vale Cc: Richard Purdie Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/leds/ledtrig-gpio.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/leds/ledtrig-gpio.c b/drivers/leds/ledtrig-gpio.c index 8183b81fca8..1bc5db4ece0 100644 --- a/drivers/leds/ledtrig-gpio.c +++ b/drivers/leds/ledtrig-gpio.c @@ -117,6 +117,9 @@ static ssize_t gpio_trig_inverted_store(struct device *dev, gpio_data->inverted = !!inverted; + /* After inverting, we need to update the LED. */ + schedule_work(&gpio_data->work); + return n; } static DEVICE_ATTR(inverted, 0644, gpio_trig_inverted_show, -- GitLab From 7b6a09f3d6aedeaac923824af2a5df30300b56e9 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Sun, 23 Aug 2009 22:54:32 +0000 Subject: [PATCH 1330/1342] powerpc/ps3: Add missing check for PS3 to rtc-ps3 platform device registration On non-PS3, we get: | kernel BUG at drivers/rtc/rtc-ps3.c:36! because the rtc-ps3 platform device is registered unconditionally in a kernel with builtin support for PS3. Reported-by: Sachin Sant Signed-off-by: Geert Uytterhoeven Acked-by: Geoff Levand Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/platforms/ps3/time.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/powerpc/platforms/ps3/time.c b/arch/powerpc/platforms/ps3/time.c index b178a1e66c9..40b5cb43300 100644 --- a/arch/powerpc/platforms/ps3/time.c +++ b/arch/powerpc/platforms/ps3/time.c @@ -21,6 +21,7 @@ #include #include +#include #include #include #include @@ -84,6 +85,9 @@ static int __init ps3_rtc_init(void) { struct platform_device *pdev; + if (!firmware_has_feature(FW_FEATURE_PS3_LV1)) + return -ENODEV; + pdev = platform_device_register_simple("rtc-ps3", -1, NULL, 0); if (IS_ERR(pdev)) return PTR_ERR(pdev); -- GitLab From b080f187adb79bbcbe28814b07cbc1ead34c469a Mon Sep 17 00:00:00 2001 From: Geoff Levand Date: Tue, 25 Aug 2009 07:53:35 +0000 Subject: [PATCH 1331/1342] powerpc/ps3: Update ps3_defconfig Update ps3_defconfig. o Refresh for 2.6.31. o Remove MTD support. o Add more HID drivers. Signed-off-by: Geoff Levand Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/configs/ps3_defconfig | 211 ++++++++++------------------- 1 file changed, 75 insertions(+), 136 deletions(-) diff --git a/arch/powerpc/configs/ps3_defconfig b/arch/powerpc/configs/ps3_defconfig index e28e65e7a0e..7de127e4cee 100644 --- a/arch/powerpc/configs/ps3_defconfig +++ b/arch/powerpc/configs/ps3_defconfig @@ -1,13 +1,14 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc5 -# Fri May 15 10:37:00 2009 +# Linux kernel version: 2.6.31-rc7 +# Mon Aug 24 17:38:50 2009 # CONFIG_PPC64=y # # Processor support # +CONFIG_PPC_BOOK3S_64=y CONFIG_PPC_BOOK3S=y # CONFIG_POWER4_ONLY is not set CONFIG_POWER3=y @@ -20,6 +21,7 @@ CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_64=y CONFIG_PPC_MM_SLICES=y CONFIG_VIRT_CPU_ACCOUNTING=y +CONFIG_PPC_HAVE_PMU_SUPPORT=y CONFIG_SMP=y CONFIG_NR_CPUS=2 CONFIG_64BIT=y @@ -31,6 +33,7 @@ CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y CONFIG_HAVE_SETUP_PER_CPU_AREA=y CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y @@ -41,7 +44,6 @@ CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_ARCH_HAS_ILOG2_U64=y CONFIG_GENERIC_HWEIGHT=y -CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_ARCH_NO_VIRT_TO_BUS=y CONFIG_PPC=y @@ -62,6 +64,7 @@ CONFIG_DTC=y # CONFIG_PPC_DCR_MMIO is not set CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -113,7 +116,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_ALL=y CONFIG_KALLSYMS_EXTRA_PASS=y -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -126,7 +128,14 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y +CONFIG_HAVE_PERF_COUNTERS=y + +# +# Performance Counters +# +# CONFIG_PERF_COUNTERS is not set CONFIG_VM_EVENT_COUNTERS=y +# CONFIG_STRIP_ASM_SYMS is not set # CONFIG_COMPAT_BRK is not set CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -145,6 +154,11 @@ CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_DMA_ATTRS=y CONFIG_USE_GENERIC_SMP_HELPERS=y + +# +# GCOV-based kernel profiling +# +# CONFIG_GCOV_KERNEL is not set # CONFIG_SLOW_WORK is not set # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y @@ -210,7 +224,7 @@ CONFIG_PPC_CELL=y # # Cell Broadband Engine options # -CONFIG_SPU_FS=y +CONFIG_SPU_FS=m CONFIG_SPU_FS_64K_LS=y # CONFIG_SPU_TRACE is not set CONFIG_SPU_BASE=y @@ -255,6 +269,7 @@ CONFIG_BINFMT_MISC=y CONFIG_HUGETLB_PAGE_SIZE_VARIABLE=y # CONFIG_IOMMU_VMERGE is not set CONFIG_IOMMU_HELPER=y +# CONFIG_SWIOTLB is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_HAS_WALK_MEMORY=y CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y @@ -285,9 +300,9 @@ CONFIG_MIGRATION=y CONFIG_PHYS_ADDR_T_64BIT=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_ARCH_MEMORY_PROBE=y CONFIG_PPC_HAS_HASH_64K=y CONFIG_PPC_4K_PAGES=y @@ -399,6 +414,7 @@ CONFIG_IPV6_NDISC_NODETYPE=y # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -433,11 +449,14 @@ CONFIG_BT_HCIBTUSB=m CONFIG_WIRELESS=y CONFIG_CFG80211=m # CONFIG_CFG80211_REG_DEBUG is not set +# CONFIG_CFG80211_DEBUGFS is not set # CONFIG_WIRELESS_OLD_REGULATORY is not set CONFIG_WIRELESS_EXT=y # CONFIG_WIRELESS_EXT_SYSFS is not set # CONFIG_LIB80211 is not set CONFIG_MAC80211=m +CONFIG_MAC80211_DEFAULT_PS=y +CONFIG_MAC80211_DEFAULT_PS_VALUE=1 # # Rate control algorithm selection @@ -447,7 +466,6 @@ CONFIG_MAC80211_RC_PID=y CONFIG_MAC80211_RC_DEFAULT_PID=y # CONFIG_MAC80211_RC_DEFAULT_MINSTREL is not set CONFIG_MAC80211_RC_DEFAULT="pid" -# CONFIG_MAC80211_MESH is not set # CONFIG_MAC80211_LEDS is not set # CONFIG_MAC80211_DEBUGFS is not set # CONFIG_MAC80211_DEBUG_MENU is not set @@ -472,77 +490,7 @@ CONFIG_EXTRA_FIRMWARE="" # CONFIG_DEBUG_DEVRES is not set # CONFIG_SYS_HYPERVISOR is not set # CONFIG_CONNECTOR is not set -CONFIG_MTD=y -CONFIG_MTD_DEBUG=y -CONFIG_MTD_DEBUG_VERBOSE=0 -# CONFIG_MTD_CONCAT is not set -# CONFIG_MTD_PARTITIONS is not set -# CONFIG_MTD_TESTS is not set - -# -# User Modules And Translation Layers -# -# CONFIG_MTD_CHAR is not set -CONFIG_MTD_BLKDEVS=y -CONFIG_MTD_BLOCK=y -# CONFIG_FTL is not set -# CONFIG_NFTL is not set -# CONFIG_INFTL is not set -# CONFIG_RFD_FTL is not set -# CONFIG_SSFDC is not set -# CONFIG_MTD_OOPS is not set - -# -# RAM/ROM/Flash chip drivers -# -# CONFIG_MTD_CFI is not set -# CONFIG_MTD_JEDECPROBE is not set -CONFIG_MTD_MAP_BANK_WIDTH_1=y -CONFIG_MTD_MAP_BANK_WIDTH_2=y -CONFIG_MTD_MAP_BANK_WIDTH_4=y -# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set -# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set -# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set -CONFIG_MTD_CFI_I1=y -CONFIG_MTD_CFI_I2=y -# CONFIG_MTD_CFI_I4 is not set -# CONFIG_MTD_CFI_I8 is not set -# CONFIG_MTD_RAM is not set -# CONFIG_MTD_ROM is not set -# CONFIG_MTD_ABSENT is not set - -# -# Mapping drivers for chip access -# -# CONFIG_MTD_COMPLEX_MAPPINGS is not set -# CONFIG_MTD_PLATRAM is not set - -# -# Self-contained MTD device drivers -# -# CONFIG_MTD_SLRAM is not set -# CONFIG_MTD_PHRAM is not set -# CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_BLOCK2MTD is not set - -# -# Disk-On-Chip Device Drivers -# -# CONFIG_MTD_DOC2000 is not set -# CONFIG_MTD_DOC2001 is not set -# CONFIG_MTD_DOC2001PLUS is not set -# CONFIG_MTD_NAND is not set -# CONFIG_MTD_ONENAND is not set - -# -# LPDDR flash memory drivers -# -# CONFIG_MTD_LPDDR is not set - -# -# UBI - Unsorted block images -# -# CONFIG_MTD_UBI is not set +# CONFIG_MTD is not set CONFIG_OF_DEVICE=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y @@ -590,10 +538,6 @@ CONFIG_BLK_DEV_SR=y # CONFIG_BLK_DEV_SR_VENDOR is not set CONFIG_CHR_DEV_SG=m # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# CONFIG_SCSI_MULTI_LUN=y # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -626,7 +570,6 @@ CONFIG_BLK_DEV_DM=m # CONFIG_DM_UEVENT is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -646,10 +589,11 @@ CONFIG_MII=m # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set CONFIG_NETDEV_1000=y CONFIG_GELIC_NET=y CONFIG_GELIC_WIRELESS=y -CONFIG_GELIC_WIRELESS_OLD_PSK_INTERFACE=y +# CONFIG_GELIC_WIRELESS_OLD_PSK_INTERFACE is not set # CONFIG_NETDEV_10000 is not set # @@ -669,8 +613,7 @@ CONFIG_WLAN_80211=y # CONFIG_HOSTAP is not set # CONFIG_B43 is not set # CONFIG_B43LEGACY is not set -CONFIG_ZD1211RW=m -# CONFIG_ZD1211RW_DEBUG is not set +# CONFIG_ZD1211RW is not set # CONFIG_RT2X00 is not set # @@ -682,7 +625,7 @@ CONFIG_ZD1211RW=m # # CONFIG_USB_CATC is not set # CONFIG_USB_KAWETH is not set -CONFIG_USB_PEGASUS=m +# CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set CONFIG_USB_USBNET=m CONFIG_USB_NET_AX8817X=m @@ -693,10 +636,11 @@ CONFIG_USB_NET_AX8817X=m # CONFIG_USB_NET_GL620A is not set # CONFIG_USB_NET_NET1080 is not set # CONFIG_USB_NET_PLUSB is not set -CONFIG_USB_NET_MCS7830=m +# CONFIG_USB_NET_MCS7830 is not set # CONFIG_USB_NET_RNDIS_HOST is not set # CONFIG_USB_NET_CDC_SUBSET is not set # CONFIG_USB_NET_ZAURUS is not set +# CONFIG_USB_NET_INT51X1 is not set # CONFIG_WAN is not set CONFIG_PPP=m CONFIG_PPP_MULTILINK=y @@ -771,8 +715,7 @@ CONFIG_DEVKMEM=y # CONFIG_UNIX98_PTYS=y # CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set -CONFIG_LEGACY_PTYS=y -CONFIG_LEGACY_PTY_COUNT=16 +# CONFIG_LEGACY_PTYS is not set # CONFIG_HVC_UDBG is not set # CONFIG_IPMI_HANDLER is not set # CONFIG_HW_RANDOM is not set @@ -782,6 +725,11 @@ CONFIG_LEGACY_PTY_COUNT=16 # CONFIG_TCG_TPM is not set # CONFIG_I2C is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y # CONFIG_GPIOLIB is not set # CONFIG_W1 is not set @@ -805,22 +753,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set # CONFIG_REGULATOR is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -# CONFIG_DAB is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -898,6 +831,11 @@ CONFIG_SND_SUPPORT_OLD_API=y CONFIG_SND_VERBOSE_PROCFS=y # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set +# CONFIG_SND_RAWMIDI_SEQ is not set +# CONFIG_SND_OPL3_LIB_SEQ is not set +# CONFIG_SND_OPL4_LIB_SEQ is not set +# CONFIG_SND_SBAWE_SEQ is not set +# CONFIG_SND_EMU10K1_SEQ is not set # CONFIG_SND_DRIVERS is not set CONFIG_SND_PPC=y CONFIG_SND_PS3=m @@ -930,29 +868,34 @@ CONFIG_USB_HIDDEV=y # Special HID drivers # # CONFIG_HID_A4TECH is not set -# CONFIG_HID_APPLE is not set -# CONFIG_HID_BELKIN is not set -# CONFIG_HID_CHERRY is not set +CONFIG_HID_APPLE=m +CONFIG_HID_BELKIN=m +CONFIG_HID_CHERRY=m # CONFIG_HID_CHICONY is not set # CONFIG_HID_CYPRESS is not set -# CONFIG_DRAGONRISE_FF is not set -# CONFIG_HID_EZKEY is not set +# CONFIG_HID_DRAGONRISE is not set +CONFIG_HID_EZKEY=m # CONFIG_HID_KYE is not set # CONFIG_HID_GYRATION is not set # CONFIG_HID_KENSINGTON is not set -# CONFIG_HID_LOGITECH is not set -# CONFIG_HID_MICROSOFT is not set +CONFIG_HID_LOGITECH=m +# CONFIG_LOGITECH_FF is not set +# CONFIG_LOGIRUMBLEPAD2_FF is not set +CONFIG_HID_MICROSOFT=m # CONFIG_HID_MONTEREY is not set # CONFIG_HID_NTRIG is not set # CONFIG_HID_PANTHERLORD is not set # CONFIG_HID_PETALYNX is not set # CONFIG_HID_SAMSUNG is not set CONFIG_HID_SONY=m -# CONFIG_HID_SUNPLUS is not set -# CONFIG_GREENASIA_FF is not set +CONFIG_HID_SUNPLUS=m +# CONFIG_HID_GREENASIA is not set +CONFIG_HID_SMARTJOYPLUS=m +# CONFIG_SMARTJOYPLUS_FF is not set # CONFIG_HID_TOPSEED is not set -# CONFIG_THRUSTMASTER_FF is not set -# CONFIG_ZEROPLUS_FF is not set +# CONFIG_HID_THRUSTMASTER is not set +# CONFIG_HID_WACOM is not set +# CONFIG_HID_ZEROPLUS is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -988,6 +931,8 @@ CONFIG_USB_EHCI_BIG_ENDIAN_MMIO=y # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=m +# CONFIG_USB_OHCI_HCD_PPC_OF_BE is not set +# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set # CONFIG_USB_OHCI_HCD_PPC_OF is not set # CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y @@ -1115,6 +1060,10 @@ CONFIG_RTC_DRV_PS3=m # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1141,11 +1090,12 @@ CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1205,7 +1155,6 @@ CONFIG_MISC_FILESYSTEMS=y # CONFIG_BEFS_FS is not set # CONFIG_BFS_FS is not set # CONFIG_EFS_FS is not set -# CONFIG_JFFS2_FS is not set # CONFIG_CRAMFS is not set # CONFIG_SQUASHFS is not set # CONFIG_VXFS_FS is not set @@ -1222,6 +1171,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -1359,7 +1309,6 @@ CONFIG_DEBUG_MEMORY_INIT=y CONFIG_DEBUG_LIST=y # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set @@ -1374,31 +1323,21 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_RING_BUFFER=y +CONFIG_EVENT_TRACING=y +CONFIG_CONTEXT_SWITCH_TRACER=y CONFIG_TRACING=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_IRQSOFF_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set -# CONFIG_FTRACE_STARTUP_TEST is not set +# CONFIG_FTRACE is not set # CONFIG_DYNAMIC_DEBUG is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set +# CONFIG_PPC_DISABLE_WERROR is not set +CONFIG_PPC_WERROR=y CONFIG_PRINT_STACK_DEPTH=64 CONFIG_DEBUG_STACKOVERFLOW=y # CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_PPC_EMULATED_STATS is not set # CONFIG_CODE_PATCHING_SELFTEST is not set # CONFIG_FTR_FIXUP_SELFTEST is not set # CONFIG_MSI_BITMAP_SELFTEST is not set -- GitLab From 52cef7555adf5ca09b3b7283097466759120d901 Mon Sep 17 00:00:00 2001 From: Eric Paris Date: Mon, 24 Aug 2009 16:03:35 -0400 Subject: [PATCH 1332/1342] inotify: seperate new watch creation updating existing watches There is nothing known wrong with the inotify watch addition/modification but this patch seperates the two code paths to make them each easy to verify as correct. Signed-off-by: Eric Paris --- fs/notify/inotify/inotify_user.c | 172 ++++++++++++++++++------------- 1 file changed, 103 insertions(+), 69 deletions(-) diff --git a/fs/notify/inotify/inotify_user.c b/fs/notify/inotify/inotify_user.c index dc32ed8323b..d8f73c25307 100644 --- a/fs/notify/inotify/inotify_user.c +++ b/fs/notify/inotify/inotify_user.c @@ -431,80 +431,29 @@ static void inotify_free_mark(struct fsnotify_mark_entry *entry) kmem_cache_free(inotify_inode_mark_cachep, ientry); } -static int inotify_update_watch(struct fsnotify_group *group, struct inode *inode, u32 arg) +static int inotify_update_existing_watch(struct fsnotify_group *group, + struct inode *inode, + u32 arg) { - struct fsnotify_mark_entry *entry = NULL; + struct fsnotify_mark_entry *entry; struct inotify_inode_mark_entry *ientry; - struct inotify_inode_mark_entry *tmp_ientry; - int ret = 0; - int add = (arg & IN_MASK_ADD); - __u32 mask; __u32 old_mask, new_mask; + __u32 mask; + int add = (arg & IN_MASK_ADD); + int ret; /* don't allow invalid bits: we don't want flags set */ mask = inotify_arg_to_mask(arg); if (unlikely(!mask)) return -EINVAL; - tmp_ientry = kmem_cache_alloc(inotify_inode_mark_cachep, GFP_KERNEL); - if (unlikely(!tmp_ientry)) - return -ENOMEM; - /* we set the mask at the end after attaching it */ - fsnotify_init_mark(&tmp_ientry->fsn_entry, inotify_free_mark); - tmp_ientry->wd = -1; - -find_entry: spin_lock(&inode->i_lock); entry = fsnotify_find_mark_entry(group, inode); spin_unlock(&inode->i_lock); - if (entry) { - ientry = container_of(entry, struct inotify_inode_mark_entry, fsn_entry); - } else { - ret = -ENOSPC; - if (atomic_read(&group->inotify_data.user->inotify_watches) >= inotify_max_user_watches) - goto out_err; -retry: - ret = -ENOMEM; - if (unlikely(!idr_pre_get(&group->inotify_data.idr, GFP_KERNEL))) - goto out_err; - - spin_lock(&group->inotify_data.idr_lock); - ret = idr_get_new_above(&group->inotify_data.idr, &tmp_ientry->fsn_entry, - group->inotify_data.last_wd, - &tmp_ientry->wd); - spin_unlock(&group->inotify_data.idr_lock); - if (ret) { - if (ret == -EAGAIN) - goto retry; - goto out_err; - } + if (!entry) + return -ENOENT; - ret = fsnotify_add_mark(&tmp_ientry->fsn_entry, group, inode); - if (ret) { - inotify_remove_from_idr(group, tmp_ientry); - if (ret == -EEXIST) - goto find_entry; - goto out_err; - } - - /* tmp_ientry has been added to the inode, so we are all set up. - * now we just need to make sure tmp_ientry doesn't get freed and - * we need to set up entry and ientry so the generic code can - * do its thing. */ - ientry = tmp_ientry; - entry = &ientry->fsn_entry; - tmp_ientry = NULL; - - atomic_inc(&group->inotify_data.user->inotify_watches); - - /* update the idr hint */ - group->inotify_data.last_wd = ientry->wd; - - /* we put the mark on the idr, take a reference */ - fsnotify_get_mark(entry); - } - - ret = ientry->wd; + ientry = container_of(entry, struct inotify_inode_mark_entry, fsn_entry); spin_lock(&entry->lock); @@ -536,18 +485,103 @@ retry: fsnotify_recalc_group_mask(group); } - /* this either matches fsnotify_find_mark_entry, or init_mark_entry - * depending on which path we took... */ + /* return the wd */ + ret = ientry->wd; + + /* match the get from fsnotify_find_mark_entry() */ fsnotify_put_mark(entry); + return ret; +} + +static int inotify_new_watch(struct fsnotify_group *group, + struct inode *inode, + u32 arg) +{ + struct inotify_inode_mark_entry *tmp_ientry; + __u32 mask; + int ret; + + /* don't allow invalid bits: we don't want flags set */ + mask = inotify_arg_to_mask(arg); + if (unlikely(!mask)) + return -EINVAL; + + tmp_ientry = kmem_cache_alloc(inotify_inode_mark_cachep, GFP_KERNEL); + if (unlikely(!tmp_ientry)) + return -ENOMEM; + + fsnotify_init_mark(&tmp_ientry->fsn_entry, inotify_free_mark); + tmp_ientry->fsn_entry.mask = mask; + tmp_ientry->wd = -1; + + ret = -ENOSPC; + if (atomic_read(&group->inotify_data.user->inotify_watches) >= inotify_max_user_watches) + goto out_err; +retry: + ret = -ENOMEM; + if (unlikely(!idr_pre_get(&group->inotify_data.idr, GFP_KERNEL))) + goto out_err; + + spin_lock(&group->inotify_data.idr_lock); + ret = idr_get_new_above(&group->inotify_data.idr, &tmp_ientry->fsn_entry, + group->inotify_data.last_wd, + &tmp_ientry->wd); + spin_unlock(&group->inotify_data.idr_lock); + if (ret) { + /* idr was out of memory allocate and try again */ + if (ret == -EAGAIN) + goto retry; + goto out_err; + } + + /* we are on the idr, now get on the inode */ + ret = fsnotify_add_mark(&tmp_ientry->fsn_entry, group, inode); + if (ret) { + /* we failed to get on the inode, get off the idr */ + inotify_remove_from_idr(group, tmp_ientry); + goto out_err; + } + + /* we put the mark on the idr, take a reference */ + fsnotify_get_mark(&tmp_ientry->fsn_entry); + + /* update the idr hint, who cares about races, it's just a hint */ + group->inotify_data.last_wd = tmp_ientry->wd; + + /* increment the number of watches the user has */ + atomic_inc(&group->inotify_data.user->inotify_watches); + + /* return the watch descriptor for this new entry */ + ret = tmp_ientry->wd; + + /* match the ref from fsnotify_init_markentry() */ + fsnotify_put_mark(&tmp_ientry->fsn_entry); + out_err: - /* could be an error, could be that we found an existing mark */ - if (tmp_ientry) { - /* on the idr but didn't make it on the inode */ - if (tmp_ientry->wd != -1) - inotify_remove_from_idr(group, tmp_ientry); + if (ret < 0) kmem_cache_free(inotify_inode_mark_cachep, tmp_ientry); - } + + return ret; +} + +static int inotify_update_watch(struct fsnotify_group *group, struct inode *inode, u32 arg) +{ + int ret = 0; + +retry: + /* try to update and existing watch with the new arg */ + ret = inotify_update_existing_watch(group, inode, arg); + /* no mark present, try to add a new one */ + if (ret == -ENOENT) + ret = inotify_new_watch(group, inode, arg); + /* + * inotify_new_watch could race with another thread which did an + * inotify_new_watch between the update_existing and the add watch + * here, go back and try to update an existing mark again. + */ + if (ret == -EEXIST) + goto retry; return ret; } -- GitLab From cf4374267fbe966e8e4e7db68f5dc7b267439780 Mon Sep 17 00:00:00 2001 From: Eric Paris Date: Mon, 24 Aug 2009 16:03:35 -0400 Subject: [PATCH 1333/1342] inotify: do not BUG on idr entries at inotify destruction If an inotify watch is left in the idr when an fsnotify group is destroyed this will lead to a BUG. This is not a dangerous situation and really indicates a programming bug and leak of memory. This patch changes it to use a WARN and a printk rather than killing people's boxes. Signed-off-by: Eric Paris --- fs/notify/inotify/inotify_fsnotify.c | 33 ++++++++++++++++++++++++++-- 1 file changed, 31 insertions(+), 2 deletions(-) diff --git a/fs/notify/inotify/inotify_fsnotify.c b/fs/notify/inotify/inotify_fsnotify.c index 5dcbafe72d7..c9ee67b442e 100644 --- a/fs/notify/inotify/inotify_fsnotify.c +++ b/fs/notify/inotify/inotify_fsnotify.c @@ -105,16 +105,45 @@ static bool inotify_should_send_event(struct fsnotify_group *group, struct inode return send; } +/* + * This is NEVER supposed to be called. Inotify marks should either have been + * removed from the idr when the watch was removed or in the + * fsnotify_destroy_mark_by_group() call when the inotify instance was being + * torn down. This is only called if the idr is about to be freed but there + * are still marks in it. + */ static int idr_callback(int id, void *p, void *data) { - BUG(); + struct fsnotify_mark_entry *entry; + struct inotify_inode_mark_entry *ientry; + static bool warned = false; + + if (warned) + return 0; + + warned = false; + entry = p; + ientry = container_of(entry, struct inotify_inode_mark_entry, fsn_entry); + + WARN(1, "inotify closing but id=%d for entry=%p in group=%p still in " + "idr. Probably leaking memory\n", id, p, data); + + /* + * I'm taking the liberty of assuming that the mark in question is a + * valid address and I'm dereferencing it. This might help to figure + * out why we got here and the panic is no worse than the original + * BUG() that was here. + */ + if (entry) + printk(KERN_WARNING "entry->group=%p inode=%p wd=%d\n", + entry->group, entry->inode, ientry->wd); return 0; } static void inotify_free_group_priv(struct fsnotify_group *group) { /* ideally the idr is empty and we won't hit the BUG in teh callback */ - idr_for_each(&group->inotify_data.idr, idr_callback, NULL); + idr_for_each(&group->inotify_data.idr, idr_callback, group); idr_remove_all(&group->inotify_data.idr); idr_destroy(&group->inotify_data.idr); } -- GitLab From dead537dd8a1c9495322c1d6f7c780697f474af0 Mon Sep 17 00:00:00 2001 From: Eric Paris Date: Mon, 24 Aug 2009 16:03:35 -0400 Subject: [PATCH 1334/1342] inotify: fix locking around inotify watching in the idr The are races around the idr storage of inotify watches. It's possible that a watch could be found from sys_inotify_rm_watch() in the idr, but it could be removed from the idr before that code does it's removal. Move the locking and the refcnt'ing so that these have to happen atomically. Signed-off-by: Eric Paris --- fs/notify/inotify/inotify_user.c | 50 +++++++++++++++++++++++++------- 1 file changed, 40 insertions(+), 10 deletions(-) diff --git a/fs/notify/inotify/inotify_user.c b/fs/notify/inotify/inotify_user.c index d8f73c25307..ce1f5823e2c 100644 --- a/fs/notify/inotify/inotify_user.c +++ b/fs/notify/inotify/inotify_user.c @@ -364,20 +364,53 @@ static int inotify_find_inode(const char __user *dirname, struct path *path, uns return error; } +/* + * Remove the mark from the idr (if present) and drop the reference + * on the mark because it was in the idr. + */ static void inotify_remove_from_idr(struct fsnotify_group *group, struct inotify_inode_mark_entry *ientry) { struct idr *idr; + struct fsnotify_mark_entry *entry; + struct inotify_inode_mark_entry *found_ientry; + int wd; spin_lock(&group->inotify_data.idr_lock); idr = &group->inotify_data.idr; - idr_remove(idr, ientry->wd); - spin_unlock(&group->inotify_data.idr_lock); + wd = ientry->wd; + + if (wd == -1) + goto out; + + entry = idr_find(&group->inotify_data.idr, wd); + if (unlikely(!entry)) + goto out; + + found_ientry = container_of(entry, struct inotify_inode_mark_entry, fsn_entry); + if (unlikely(found_ientry != ientry)) { + /* We found an entry in the idr with the right wd, but it's + * not the entry we were told to remove. eparis seriously + * fucked up somewhere. */ + WARN_ON(1); + ientry->wd = -1; + goto out; + } + + /* One ref for being in the idr, one ref held by the caller */ + BUG_ON(atomic_read(&entry->refcnt) < 2); + + idr_remove(idr, wd); ientry->wd = -1; + + /* removed from the idr, drop that ref */ + fsnotify_put_mark(entry); +out: + spin_unlock(&group->inotify_data.idr_lock); } + /* - * Send IN_IGNORED for this wd, remove this wd from the idr, and drop the - * internal reference help on the mark because it is in the idr. + * Send IN_IGNORED for this wd, remove this wd from the idr. */ void inotify_ignored_and_remove_idr(struct fsnotify_mark_entry *entry, struct fsnotify_group *group) @@ -417,9 +450,6 @@ skip_send_ignore: /* remove this entry from the idr */ inotify_remove_from_idr(group, ientry); - /* removed from idr, drop that reference */ - fsnotify_put_mark(entry); - atomic_dec(&group->inotify_data.user->inotify_watches); } @@ -535,6 +565,9 @@ retry: goto out_err; } + /* we put the mark on the idr, take a reference */ + fsnotify_get_mark(&tmp_ientry->fsn_entry); + /* we are on the idr, now get on the inode */ ret = fsnotify_add_mark(&tmp_ientry->fsn_entry, group, inode); if (ret) { @@ -543,9 +576,6 @@ retry: goto out_err; } - /* we put the mark on the idr, take a reference */ - fsnotify_get_mark(&tmp_ientry->fsn_entry); - /* update the idr hint, who cares about races, it's just a hint */ group->inotify_data.last_wd = tmp_ientry->wd; -- GitLab From 0db501bd0610ee0c0aca84d927f90bcccd09e2bd Mon Sep 17 00:00:00 2001 From: "Eric W. Biederman" Date: Thu, 27 Aug 2009 03:20:04 -0700 Subject: [PATCH 1335/1342] inotify: Ensure we alwasy write the terminating NULL. Before the rewrite copy_event_to_user always wrote a terqminating '\0' byte to user space after the filename. Since the rewrite that terminating byte was skipped if your filename is exactly a multiple of event_size. Ouch! So add one byte to name_size before we round up and use clear_user to set userspace to zero like /dev/zero does instead of copying the strange nul_inotify_event. I can't quite convince myself len_to_zero will never exceed 16 and even if it doesn't clear_user should be more efficient and a more accurate reflection of what the code is trying to do. Signed-off-by: Eric W. Biederman Signed-off-by: Eric Paris --- fs/notify/inotify/inotify_user.c | 13 ++++++------- 1 file changed, 6 insertions(+), 7 deletions(-) diff --git a/fs/notify/inotify/inotify_user.c b/fs/notify/inotify/inotify_user.c index ce1f5823e2c..0e781bc88d1 100644 --- a/fs/notify/inotify/inotify_user.c +++ b/fs/notify/inotify/inotify_user.c @@ -47,9 +47,6 @@ static struct vfsmount *inotify_mnt __read_mostly; -/* this just sits here and wastes global memory. used to just pad userspace messages with zeros */ -static struct inotify_event nul_inotify_event; - /* these are configurable via /proc/sys/fs/inotify/ */ static int inotify_max_user_instances __read_mostly; static int inotify_max_queued_events __read_mostly; @@ -199,8 +196,10 @@ static ssize_t copy_event_to_user(struct fsnotify_group *group, inotify_free_event_priv(fsn_priv); } - /* round up event->name_len so it is a multiple of event_size */ - name_len = roundup(event->name_len, event_size); + /* round up event->name_len so it is a multiple of event_size + * plus an extra byte for the terminating '\0'. + */ + name_len = roundup(event->name_len + 1, event_size); inotify_event.len = name_len; inotify_event.mask = inotify_mask_to_arg(event->mask); @@ -224,8 +223,8 @@ static ssize_t copy_event_to_user(struct fsnotify_group *group, return -EFAULT; buf += event->name_len; - /* fill userspace with 0's from nul_inotify_event */ - if (copy_to_user(buf, &nul_inotify_event, len_to_zero)) + /* fill userspace with 0's */ + if (clear_user(buf, len_to_zero)) return -EFAULT; buf += len_to_zero; event_size += name_len; -- GitLab From 9886e836a6a5dbd273dc55b17e713f0a188d137f Mon Sep 17 00:00:00 2001 From: David Howells Date: Thu, 27 Aug 2009 13:09:06 +0100 Subject: [PATCH 1336/1342] AFS: Stop readlink() on AFS crashing due to NULL 'file' ptr kAFS crashes when asked to read a symbolic link because page_getlink() passes a NULL file pointer to read_mapping_page(), but afs_readpage() expects a file pointer from which to extract a key. Modify afs_readpage() to request the appropriate key from the calling process's keyrings if a file struct is not supplied with one attached. Signed-off-by: David Howells Acked-by: Anton Blanchard Signed-off-by: Linus Torvalds --- fs/afs/file.c | 18 +++++++++++++++--- 1 file changed, 15 insertions(+), 3 deletions(-) diff --git a/fs/afs/file.c b/fs/afs/file.c index 0149dab365e..681c2a7b013 100644 --- a/fs/afs/file.c +++ b/fs/afs/file.c @@ -134,9 +134,16 @@ static int afs_readpage(struct file *file, struct page *page) inode = page->mapping->host; - ASSERT(file != NULL); - key = file->private_data; - ASSERT(key != NULL); + if (file) { + key = file->private_data; + ASSERT(key != NULL); + } else { + key = afs_request_key(AFS_FS_S(inode->i_sb)->volume->cell); + if (IS_ERR(key)) { + ret = PTR_ERR(key); + goto error_nokey; + } + } _enter("{%x},{%lu},{%lu}", key_serial(key), inode->i_ino, page->index); @@ -207,12 +214,17 @@ static int afs_readpage(struct file *file, struct page *page) unlock_page(page); } + if (!file) + key_put(key); _leave(" = 0"); return 0; error: SetPageError(page); unlock_page(page); + if (!file) + key_put(key); +error_nokey: _leave(" = %d", ret); return ret; } -- GitLab From 788d908f2879a17e5f80924f3da2e23f1034482d Mon Sep 17 00:00:00 2001 From: Julien TINNES Date: Thu, 27 Aug 2009 15:26:58 +0200 Subject: [PATCH 1337/1342] ipv4: make ip_append_data() handle NULL routing table Add a check in ip_append_data() for NULL *rtp to prevent future bugs in callers from being exploitable. Signed-off-by: Julien Tinnes Signed-off-by: Tavis Ormandy Acked-by: David S. Miller Signed-off-by: Linus Torvalds --- net/ipv4/ip_output.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/net/ipv4/ip_output.c b/net/ipv4/ip_output.c index 7d082105472..7ffcd96fe59 100644 --- a/net/ipv4/ip_output.c +++ b/net/ipv4/ip_output.c @@ -813,6 +813,8 @@ int ip_append_data(struct sock *sk, inet->cork.addr = ipc->addr; } rt = *rtp; + if (unlikely(!rt)) + return -EFAULT; /* * We steal reference to this route, caller should not release it */ -- GitLab From 4f8ee2c9cc0e885d2bb50ef26db66150ab25213e Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Thu, 27 Aug 2009 17:20:30 +1000 Subject: [PATCH 1338/1342] lmb: Remove __init from lmb_end_of_DRAM() We call lmb_end_of_DRAM() to test whether a DMA mask is ok on a machine without IOMMU, but this function is marked as __init. I don't think there's a clean way to get the top of RAM max_pfn doesn't appear to include highmem or I missed (or we have a bug :-) so for now, let's just avoid having a broken 2.6.31 by making this function non-__init and we can revisit later. Signed-off-by: Benjamin Herrenschmidt Signed-off-by: Linus Torvalds --- lib/lmb.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/lib/lmb.c b/lib/lmb.c index e4a6482d8b2..0343c05609f 100644 --- a/lib/lmb.c +++ b/lib/lmb.c @@ -429,7 +429,7 @@ u64 __init lmb_phys_mem_size(void) return lmb.memory.size; } -u64 __init lmb_end_of_DRAM(void) +u64 lmb_end_of_DRAM(void) { int idx = lmb.memory.cnt - 1; -- GitLab From 0a80fb10239b04c45e5e80aad8d4b2ca5ac407b2 Mon Sep 17 00:00:00 2001 From: Jeremy Fitzhardinge Date: Thu, 27 Aug 2009 12:22:43 -0700 Subject: [PATCH 1339/1342] xenfb: connect to backend before registering fb As soon as the framebuffer is registered, our methods may be called by the kernel. This leads to a crash as xenfb_refresh() gets called before we have the irq. Connect to the backend before registering our framebuffer with the kernel. [ Fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=14059 ] Signed-off-by: Michal Schmidt Signed-off-by: Jeremy Fitzhardinge Signed-off-by: Linus Torvalds --- drivers/video/xen-fbfront.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/video/xen-fbfront.c b/drivers/video/xen-fbfront.c index 15502d5e364..54cd9161017 100644 --- a/drivers/video/xen-fbfront.c +++ b/drivers/video/xen-fbfront.c @@ -454,6 +454,10 @@ static int __devinit xenfb_probe(struct xenbus_device *dev, xenfb_init_shared_page(info, fb_info); + ret = xenfb_connect_backend(dev, info); + if (ret < 0) + goto error; + ret = register_framebuffer(fb_info); if (ret) { fb_deferred_io_cleanup(fb_info); @@ -464,10 +468,6 @@ static int __devinit xenfb_probe(struct xenbus_device *dev, } info->fb_info = fb_info; - ret = xenfb_connect_backend(dev, info); - if (ret < 0) - goto error; - xenfb_make_preferred_console(); return 0; -- GitLab From 7d1d16e416e61aeef8655d542f8e4a4fc6e808e4 Mon Sep 17 00:00:00 2001 From: Rusty Russell Date: Wed, 26 Aug 2009 22:02:54 +0930 Subject: [PATCH 1340/1342] module: fix BUG_ON() for powerpc (and other function descriptor archs) The rarely-used symbol_put_addr() needs to use dereference_function_descriptor on powerpc. Reported-by: Paul Mackerras Signed-off-by: Rusty Russell --- kernel/module.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/kernel/module.c b/kernel/module.c index fd141140355..07c80e68a6c 100644 --- a/kernel/module.c +++ b/kernel/module.c @@ -909,16 +909,18 @@ void __symbol_put(const char *symbol) } EXPORT_SYMBOL(__symbol_put); +/* Note this assumes addr is a function, which it currently always is. */ void symbol_put_addr(void *addr) { struct module *modaddr; + unsigned long a = (unsigned long)dereference_function_descriptor(addr); - if (core_kernel_text((unsigned long)addr)) + if (core_kernel_text(a)) return; /* module_text_address is safe here: we're supposed to have reference * to module from symbol_get, so it can't go away. */ - modaddr = __module_text_address((unsigned long)addr); + modaddr = __module_text_address(a); BUG_ON(!modaddr); module_put(modaddr); } -- GitLab From 1b364bf438cf337a3818aee77d68c0713f3e1fc4 Mon Sep 17 00:00:00 2001 From: James Bottomley Date: Wed, 26 Aug 2009 22:04:12 +0930 Subject: [PATCH 1341/1342] module: workaround duplicate section names The root cause is a duplicate section name (.text); is this legal? [ Amerigo Wang: "AFAIK, yes." ] However, there's a problem with commit 6d76013381ed28979cd122eb4b249a88b5e384fa in that if you fail to allocate a mod->sect_attrs (in this case it's null because of the duplication), it still gets used without checking in add_notes_attrs() This should fix it [ This patch leaves other problems, particularly the sections directory, but recent parisc toolchains seem to produce these modules and this prevents a crash and is a minimal change -- RR ] Signed-off-by: James Bottomley Signed-off-by: Rusty Russell Tested-by: Helge Deller Signed-off-by: Linus Torvalds --- kernel/module.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/kernel/module.c b/kernel/module.c index 07c80e68a6c..eccb561dd8a 100644 --- a/kernel/module.c +++ b/kernel/module.c @@ -2355,7 +2355,8 @@ static noinline struct module *load_module(void __user *umod, if (err < 0) goto unlink; add_sect_attrs(mod, hdr->e_shnum, secstrings, sechdrs); - add_notes_attrs(mod, hdr->e_shnum, secstrings, sechdrs); + if (mod->sect_attrs) + add_notes_attrs(mod, hdr->e_shnum, secstrings, sechdrs); /* Get rid of temporary copy */ vfree(hdr); -- GitLab From 326ba5010a5429a5a528b268b36a5900d4ab0eba Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Thu, 27 Aug 2009 17:59:04 -0700 Subject: [PATCH 1342/1342] Linux 2.6.31-rc8 --- Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Makefile b/Makefile index 9c87e60d169..25c615e5730 100644 --- a/Makefile +++ b/Makefile @@ -1,7 +1,7 @@ VERSION = 2 PATCHLEVEL = 6 SUBLEVEL = 31 -EXTRAVERSION = -rc7 +EXTRAVERSION = -rc8 NAME = Man-Eating Seals of Antiquity # *DOCUMENTATION* -- GitLab